Monitoring severe accidents using AI techniques

Energy Technology Data Exchange (ETDEWEB)

No, Young Gyu; Ahn, Kwang Il [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kim, Ju Hyun; Na, Man Gyun [Dept. of Nuclear Engineering, Chosun University, Gwangju (Korea, Republic of); Lim, Dong Hyuk [Korea Institute of Nuclear Nonproliferation and Control, Daejon (Korea, Republic of)

2012-05-15

After the Fukushima nuclear accident in 2011, there has been increasing concern regarding severe accidents in nuclear facilities. Severe accident scenarios are difficult for operators to monitor and identify. Therefore, accurate prediction of a severe accident is important in order to manage it appropriately in the unfavorable conditions. In this study, artificial intelligence (AI) techniques, such as support vector classification (SVC), probabilistic neural network (PNN), group method of data handling (GMDH), and fuzzy neural network (FNN), were used to monitor the major transient scenarios of a severe accident caused by three different initiating events, the hot-leg loss of coolant accident (LOCA), the cold-leg LOCA, and the steam generator tube rupture in pressurized water reactors (PWRs). The SVC and PNN models were used for the event classification. The GMDH and FNN models were employed to accurately predict the important timing representing severe accident scenarios. In addition, in order to verify the proposed algorithm, data from a number of numerical simulations were required in order to train the AI techniques due to the shortage of real LOCA data. The data was acquired by performing simulations using the MAAP4 code. The prediction accuracy of the three types of initiating events was sufficiently high to predict severe accident scenarios. Therefore, the AI techniques can be applied successfully in the identification and monitoring of severe accident scenarios in real PWRs.

Monitoring severe accidents using AI techniques

International Nuclear Information System (INIS)

No, Young Gyu; Ahn, Kwang Il; Kim, Ju Hyun; Na, Man Gyun; Lim, Dong Hyuk

2012-01-01

After the Fukushima nuclear accident in 2011, there has been increasing concern regarding severe accidents in nuclear facilities. Severe accident scenarios are difficult for operators to monitor and identify. Therefore, accurate prediction of a severe accident is important in order to manage it appropriately in the unfavorable conditions. In this study, artificial intelligence (AI) techniques, such as support vector classification (SVC), probabilistic neural network (PNN), group method of data handling (GMDH), and fuzzy neural network (FNN), were used to monitor the major transient scenarios of a severe accident caused by three different initiating events, the hot-leg loss of coolant accident (LOCA), the cold-leg LOCA, and the steam generator tube rupture in pressurized water reactors (PWRs). The SVC and PNN models were used for the event classification. The GMDH and FNN models were employed to accurately predict the important timing representing severe accident scenarios. In addition, in order to verify the proposed algorithm, data from a number of numerical simulations were required in order to train the AI techniques due to the shortage of real LOCA data. The data was acquired by performing simulations using the MAAP4 code. The prediction accuracy of the three types of initiating events was sufficiently high to predict severe accident scenarios. Therefore, the AI techniques can be applied successfully in the identification and monitoring of severe accident scenarios in real PWRs.

SEVERE ACCIDENT MANAGEMENT STATUS AT Loviisa

International Nuclear Information System (INIS)

Kymalainen, O.; Tuomisto, H.

1997-01-01

Some of the specific design features of IVO's Loviisa Plant, most notably the ice-condenser containment, strongly affect the plant response in a hypothetical core melt accident. They have together with the relatively stringent Finnish regulatory requirements forced IVO to develop a tailor made severe accident management strategy for Loviisa. The low design pressure of the ice-condenser containment complicates the design of the hydrogen management system. On the other hand, the ice-condensers and the water available from them are facilitating factors regarding in-vessel retention of corium by external cooling of reactor pressure vessel. This paper summarizes the Finnish severe accident requirements, IVO's approach to severe accidents, and its application to the Loviisa Plant

Design and Development of a Severe Accident Training System

International Nuclear Information System (INIS)

Kim, Ko Ryu; Park, Sun Hee; Kim, Dong Ha

2005-01-01

The nuclear plants' severe accidents have two big characteristics. One is that they are very rare accidents, and the other is that they bring extreme conditions such as the high pressure and temperature in their process. It is, therefore, very hard to get the severe accident data, without inquiring that the data should be real or experimental. In fact, most of severe accident analyses rely on the simulation codes where almost all severe accident knowledge is contained. These codes are, however, programmed by the Fortran language, so that their output are typical text files which are very complicated. To avoid this kind of difficulty in understanding the code output data, several kinds of graphic user interface (GUI) programs could be developed. In this paper, we will introduce a GUI system for severe accident management and training, partly developed and partly in design stage

Highly Reliable Power and Communication System for Essential Instruments under a Severe Accident of NPPs

Energy Technology Data Exchange (ETDEWEB)

Yoo, S. J.; Choi, B. H.; Jung, S. Y.; Rim, Chun T. [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

2013-10-15

In this paper, three survivable strategies to overcome the problems listed above are proposed for the essential instruments under the severe accident of NPPs. First, wire/wireless multi power systems are adopted to the essential instruments for continuous power supply. Second, wire/wireless communication systems are proposed for reliable transmission of measuring information among instruments and operators. Third, a physical protection system such as a harness and a heat isolation box is introduced to ensure operable conditions for the proposed systems. In this paper, a highly reliable strategy, which consists of wire/wireless multi power and communication systems and physical protection system is proposed to ensure the survival of the essential instruments under harsh external conditions. The wire/wireless multi power and communication systems are designed to transfer power and data in spite of the failure of conventional wired systems. The physical protection system provides operable environments to the instruments. Therefore, the proposed system can be considered as a candidate of practical and urgent remedy for NPPs under the severe accident. After the Fukushima nuclear accident, survivability of essential instruments has been emphasized for immediate and accurate response. The essential instruments can measure environment conditions such as temperature, pressure, radioactivity and corium behavior inside nuclear power plants (NPPs) under a severe accident. Access to the inside of NPPs is restricted to human beings because of hazardous environment such as high radioactivity, high temperature and high pressure. Thus, monitoring the inside of NPPs is necessary for avoiding damage from the severe accident. Even though there were a number of instruments in Fukushima Daiichi NPP, they failed to obtain exact monitoring information. According to the details of the Fukushima nuclear accident, following problems can be counted as strong candidates of this instruments

Highly Reliable Power and Communication System for Essential Instruments under a Severe Accident of NPPs

International Nuclear Information System (INIS)

Yoo, S. J.; Choi, B. H.; Jung, S. Y.; Rim, Chun T.

2013-01-01

In this paper, three survivable strategies to overcome the problems listed above are proposed for the essential instruments under the severe accident of NPPs. First, wire/wireless multi power systems are adopted to the essential instruments for continuous power supply. Second, wire/wireless communication systems are proposed for reliable transmission of measuring information among instruments and operators. Third, a physical protection system such as a harness and a heat isolation box is introduced to ensure operable conditions for the proposed systems. In this paper, a highly reliable strategy, which consists of wire/wireless multi power and communication systems and physical protection system is proposed to ensure the survival of the essential instruments under harsh external conditions. The wire/wireless multi power and communication systems are designed to transfer power and data in spite of the failure of conventional wired systems. The physical protection system provides operable environments to the instruments. Therefore, the proposed system can be considered as a candidate of practical and urgent remedy for NPPs under the severe accident. After the Fukushima nuclear accident, survivability of essential instruments has been emphasized for immediate and accurate response. The essential instruments can measure environment conditions such as temperature, pressure, radioactivity and corium behavior inside nuclear power plants (NPPs) under a severe accident. Access to the inside of NPPs is restricted to human beings because of hazardous environment such as high radioactivity, high temperature and high pressure. Thus, monitoring the inside of NPPs is necessary for avoiding damage from the severe accident. Even though there were a number of instruments in Fukushima Daiichi NPP, they failed to obtain exact monitoring information. According to the details of the Fukushima nuclear accident, following problems can be counted as strong candidates of this instruments

Severe Accidents: French Regulatory Practice for Nuclear Power Plants

International Nuclear Information System (INIS)

Colin, M.

1997-01-01

In the framework of a continuous and iterative process, the French Safety Authority asks the utility EDF to implement equipment and procedure modifications on the operating reactors, in order to cope with the most likely Severe Accident sequences. As a result of Probabilistic Safety Assessments published in 1990, important equipment and procedure modifications are being implemented on the French PWRs to improve the safety in shutdown states. The implementation of another set of modifications against some reactivity accident sequences is also in progress. More recently, the Safety Authority expressed specific Severe Accident requirements in terms of instrumentation, equipment qualification, high pressure core melt accidents and hydrogen risk prevention. In that respect, EDF was asked to implement hydrogen recombiners on its reactors. On the other hand, the French Safety authority is involved with its German counterpart in the assessment process of the European Pressurized Water Reactor Project. In consistency with the common recommendations of the Safety Authorities involved, Severe Accident provisions for this reactor are being taken into account at the design stage

The management of severe accidents in modern pressure tube reactors

International Nuclear Information System (INIS)

Popov, N.K.; Santamaura, P.; Blahnik, C.; Snell, V.G.; Duffey, R.B.

2007-01-01

Advanced new reactor designs resist severe accidents through a balance between prevention and mitigation. This balance is achieved by designing to ensure that such accidents are very rare; and by limiting core damage progression and releases from the plant in the event of such rare accidents. These design objectives are supported by a suitable combination of probabilistic safety analysis, engineering judgment and experimental and analytical study. This paper describes the approach used for the Advanced CANDU Reactor TM -1000 (ACR-1000) design, which includes provisions to both prevent and mitigate severe accidents. The paper describes the use of PSA as a 'design assist' tool; the analysis of core damage progression pathways; the definition of the core damage states; the capability of the mitigating systems to stop and control severe accident events; and the severe accident management opportunities for consequence reduction. (author)

Instrumentation for the follow-up of severe accidents

International Nuclear Information System (INIS)

Munoz Sanchez, A.; Nino Perote, R.

2000-01-01

During severe accidents, it is foreseeable that the instrumentation installed in a plant is subjected to conditions which are more hostile than those for which the instrumentation was designed and qualified. Moreover, new, specific instrumentation is required to monitor variables which have not been considered until now, and to control systems which lessen the consequences of severe accidents. Both existing instrumentation used to monitor critical functions in design basis accident conditions and additional instrumentation which provides the information necessary to control and mitigate the consequences of severe accidents, have to be designed to withstand such conditions, especially in terms of measurements range, functional characteristics and qualification to withstand pressure and temperature loads resulting from steam explosion, hydrogen combustion/explosion and high levels of radiation over long periods of time. (Author)

Development of Highly Survivable Power and Communication System for NPP Instruments under Severe Accident

Energy Technology Data Exchange (ETDEWEB)

Yoo, Seung J.; Gu, Beom W.; Nguyen, Duy T.; Choi, Bo H.; Rim, Chun T. [KAIST, Daejeon (Korea, Republic of); Lee, So I. [KHNP CRI, Daejeon (Korea, Republic of)

2014-10-15

According to the detail report from the Fukushima nuclear accident, the failure of conventional instruments is mainly due to the following reasons. 1) Insufficient backup battery capacity after the station black out (SBO) 2) The malfunction or damage of instruments due to the extremely harsh ambient condition after the severe accident 3) The cut-off of power and communication cable due to the physical shocks of hydrogen explosion after the severe accident Since the current equipment qualification (EQ) for the NPP instruments is based on the design basis accident such as loss of coolant accident (LOCA), conventional instruments, which are examined under EQ condition, cannot guarantee their normal operation during the severe accident. A 7m-long-distance wireless power transfer and a radio frequency (RF) communication were introduced with conventional wired system to increase a redundancy. A heat isolation box and a harness are adopted to provide a protection from the expected physical shocks such as missiles and drastic increase of ambient temperature and pressure. A detail design principle of the highly survivable power and communication system, which has 4 sub-systems of a DCRS wireless power transfer, a Zigbee wireless communication, a GFRP harness, and a passive type router with a fly back regulator, has been presented in this paper. Each sub-system has been designed to have a robust operation characteristic regardless of the estimated physical shocks after the severe accident.

Development of Highly Survivable Power and Communication System for NPP Instruments under Severe Accident

International Nuclear Information System (INIS)

Yoo, Seung J.; Gu, Beom W.; Nguyen, Duy T.; Choi, Bo H.; Rim, Chun T.; Lee, So I.

2014-01-01

According to the detail report from the Fukushima nuclear accident, the failure of conventional instruments is mainly due to the following reasons. 1) Insufficient backup battery capacity after the station black out (SBO) 2) The malfunction or damage of instruments due to the extremely harsh ambient condition after the severe accident 3) The cut-off of power and communication cable due to the physical shocks of hydrogen explosion after the severe accident Since the current equipment qualification (EQ) for the NPP instruments is based on the design basis accident such as loss of coolant accident (LOCA), conventional instruments, which are examined under EQ condition, cannot guarantee their normal operation during the severe accident. A 7m-long-distance wireless power transfer and a radio frequency (RF) communication were introduced with conventional wired system to increase a redundancy. A heat isolation box and a harness are adopted to provide a protection from the expected physical shocks such as missiles and drastic increase of ambient temperature and pressure. A detail design principle of the highly survivable power and communication system, which has 4 sub-systems of a DCRS wireless power transfer, a Zigbee wireless communication, a GFRP harness, and a passive type router with a fly back regulator, has been presented in this paper. Each sub-system has been designed to have a robust operation characteristic regardless of the estimated physical shocks after the severe accident

Integrity of PWR pressure vessels during overcooling accidents

International Nuclear Information System (INIS)

Cheverton, R.D.; Iskander, S.K.; Whitman, G.D.

1982-01-01

The reactor pressure vessel in a pressurized water reactor is normally subjected to temperatures and pressures that preclude propagation of sharp, crack-like defects that might exist in the wall of the vessel. However, there is a class of postulated accidents, referred to as overcooling accidents, that can subject the pressure vessel to severe thermal shock while the pressure is substantial. As a result of such accidents vessels containing high concentrations of copper and nickel, which enhance radiation embrittlement, may possess a potential for extensive propagation of preexistent inner surface flaws prior to the vessel's normal end of life. For the purpose of evaluating this problem a state-of-the-art fracture mechanics model was developed and has been used for conducting parametric analyses and for calculating several recorded PWR transients. Results of the latter analysis indicate that there may be some vessels that have a potential for failure today if subjected to a Rancho Seco (1978) or TMI-2 (1979) type transient. However, the calculational model may be excessively conservative, and this possibility is under investigation

Integrity of PWR pressure vessels during overcooling accidents

International Nuclear Information System (INIS)

Cheverton, R.D.; Iskander, S.K.; Whitman, G.D.

1982-01-01

The reactor pressure vessel in a pressurized water reactor is normally subjected to temperatures and pressures that preclude propagation of sharp, crack-like defects that might exist in the wall of the vessel. However, there is a class of postulated accidents, referred to as overcooling accidents, that can subject the pressure vessel to severe thermal shock while the pressure is substantial. As a result of such accidents, vessels containing high concentrations of copper and nickel, which enhance radiation embrittlement, may possess a potential for extensive propagation of preexistent inner surface flaws prior to the vessel's normal end of life. A state-of-the-art fracture-mechanics model was developed and has been used for conducting parametric analyses and for calculating several recorded PWR transients. Results of the latter analysis indicate that there may be some vessels that have a potential for failure in a few years if subjected to a Rancho Seco-type transient. However, the calculational model may be excessively conservative, and this possibility is under investigation

A Novel Thermal-Mechanical Detection System for Reactor Pressure Vessel Bottom Failure Monitoring in Severe Accidents

International Nuclear Information System (INIS)

Bi, Daowei; Bu, Jiangtao; Xu, Dongling

2013-06-01

Following the Fukushima Daiichi nuclear accident in Japan, there is an increased need of enhanced capabilities for severe accident management (SAM) program. Among others, a reliable method for detecting reactor pressure vessel (RPV) bottom failure has been evaluated as imperative by many utility owners. Though radiation and/or temperature measurement are potential solutions by tradition, there are some limitations for them to function desirably in such severe accident as that in Japan. To provide reliable information for assessment of accident progress in SAM program, in this paper we propose a novel thermal-mechanical detection system (TMDS) for RPV bottom failure monitoring in severe accidents. The main components of TMDS include thermally sensitive element, metallic cables, tension controlled switch and main control room annunciation device. With TMDS installed, there shall be a reliable means of keeping SAM decision-makers informed whether the RPV bottom has indeed failed. Such assurance definitely guarantees enhancement of severe accident management performance and significantly improve nuclear safety and thus protect the society and people. (authors)

Numerical Study of Severe Accidents on Containment Venting Conditions

Energy Technology Data Exchange (ETDEWEB)

Lee, Na Rae; Bang, Young Suk; Park, Tong Kyu; Lee, Doo Yong [FNC Technology Co., Yongin (Korea, Republic of); Choi, Yu Jung; Lee, Sang Won; Kim, Hyeong Taek [KHNP-CRI, Daejeon (Korea, Republic of)

2014-10-15

flow would contain the significant amount of radioactive materials, which have harmful effects on the public and the environment. In this study, the effects of venting during the severe accident with containment pressurization and the vent flow characteristics are examined by using MAAP5 simulations with accident scenarios carefully selected to cover the major containment pressurization phenomena. Based on the calculation results, the followings can be concluded: - The vent initiation pressure should be sufficiently high to delay the vent. The suspended particles (i.e. aerosols) in containment would be settled and deposited; thus, the less amount of aerosol would be vented as the time elapsed. - At the same time, the vent initiation pressure should not be too high. There could be leakages of radionuclide through airlocks and doors. Also, venting at high pressure would induce the flashing the water in the cavity, which worsen the containment pressure control and the cooling recovery.

Numerical Study of Severe Accidents on Containment Venting Conditions

International Nuclear Information System (INIS)

Lee, Na Rae; Bang, Young Suk; Park, Tong Kyu; Lee, Doo Yong; Choi, Yu Jung; Lee, Sang Won; Kim, Hyeong Taek

2014-01-01

flow would contain the significant amount of radioactive materials, which have harmful effects on the public and the environment. In this study, the effects of venting during the severe accident with containment pressurization and the vent flow characteristics are examined by using MAAP5 simulations with accident scenarios carefully selected to cover the major containment pressurization phenomena. Based on the calculation results, the followings can be concluded: - The vent initiation pressure should be sufficiently high to delay the vent. The suspended particles (i.e. aerosols) in containment would be settled and deposited; thus, the less amount of aerosol would be vented as the time elapsed. - At the same time, the vent initiation pressure should not be too high. There could be leakages of radionuclide through airlocks and doors. Also, venting at high pressure would induce the flashing the water in the cavity, which worsen the containment pressure control and the cooling recovery

Water level measurement system in reactor pressure vessel of BWR and hydrogen concentration monitoring system for severe accident

International Nuclear Information System (INIS)

Kuroda, Hidehiko; Okazaki, Koki; Shiraishi, Fujio; Kenjyo, Hiroaki; Isoda, Koichiro

2013-01-01

TEPCO's Fukushima Daiichi Nuclear Power Station Accident caused severe accident to lose functions of many instrumentation systems. As a result, many important plant parameters couldn't be monitored. In order to monitor plant parameters in the case of severe accident, new instrumentation systems available in the severe conditions are being developed. Water level in reactor pressure vessel and hydrogen concentration in primary containment vessel are one of the most important parameters. Performance test results about water level measurement sensor and hydrogen sensor in severe environmental conditions are described. (author)

High-speed radiation dose calculations for severe accidents using INDOS

International Nuclear Information System (INIS)

Davidson, G.R.; Godin-Jacqmin, L.J.; Raines, J.C.

1992-01-01

The computer code INDOS (in-plant dose) has been developed for the high-speed calculation of in-plant radiation dose rates and doses during and/or due to a severe accident at a nuclear power plant. This paper describes the current capabilities of the code and presents the results of calculations for several severe-accident scenarios. The INDOS code can be run either as a module of MAAP, a code widely used in the nuclear industry for simulating the response of a light water reactor system during severe accidents, or as a stand-alone code using output from an alternative companion code. INDOS calculates gamma dose rates and doses in major plant compartments caused by airborne and deposited fission products released during an accident. The fission product concentrations are determined by the companion code

A CANDU Severe Accident Analysis

International Nuclear Information System (INIS)

Negut, Gheorghe; Catana, Alexandru; Prisecaru, Ilie

2006-01-01

As interest in severe accident studies has increased in the last years, we have developed a set of simple models to analyze severe accidents for CANDU reactors that should be integrated in the EU codes. The CANDU600 reactor uses natural uranium fuel and heavy water (D2O) as both moderator and coolant, with the moderator and coolant in separate systems. We chose to analyze accident development for a LOCA with simultaneous loss of moderator cooling and the loss of emergency core cooling system (ECCS). This type of accident is likely to modify the reactor geometry and will lead to a severe accident development. When the coolant temperatures inside a pressure tube reaches 10000 deg C, a contact between pressure tube and calandria tube occurs and the residual heat is transferred to the moderator. Due to the lack of cooling, the moderator eventually begins to boil and is expelled, through the calandria vessel relief ducts, into the containment. Therefore the calandria tubes (fuel channels) will be uncovered, then will disintegrate and fall down to the calandria vessel bottom. After all the quantity of moderator is vaporized and expelled, the debris will heat up and eventually boil. The heat accumulated in the molten debris will be transferred through the calandria vessel wall to the shield tank water, which normally surrounds the calandria vessel. The phenomena described above are modelled, analyzed and compared with the existing data. The results are encouraging. (authors)

A severe accident analysis for the system-integrated modular advanced reactor

International Nuclear Information System (INIS)

Jung, Gunhyo; Jae, Moosung

2015-01-01

The System-Integrated Modular Advanced Reactor (SMART) that has been recently designed in KOREA and has acquired standard design certification from the nuclear power regulatory body (NSSC) is an integral type reactor with 330MW thermal power. It is a small sized reactor in which the core, steam generator, pressurizer, and reactor coolant pump that are in existing pressurized light water reactors are designed to be within a pressure vessel without any separate pipe connection. In addition, this reactor has much different design characteristics from existing pressurized light water reactors such as the adoption of a passive residual heat removal system and a cavity flooding system. Therefore, the safety of the SMART against severe accidents should be checked through severe accident analysis reflecting the design characteristics of the SMART. For severe accident analysis, an analysis model has been developed reflecting the design information presented in the standard design safety analysis report. The severe accident analysis model has been developed using the MELCOR code that is widely used to evaluate pressurized LWR severe accidents. The steady state accident analysis model for the SMART has been simulated. According to the analysis results, the developed model reflecting the design of the SMART is found to be appropriate. Severe accident analysis has been performed for the representative accident scenarios that lead to core damage to check the appropriateness of the severe accident management plan for the SMART. The SMART has been shown to be safe enough to prevent severe accidents by utilizing severe accident management systems such as a containment spray system, a passive hydrogen recombiner, and a cavity flooding system. In addition, the SMART is judged to have been technically improved remarkably compared to existing PWRs. The SMART has been designed to have a larger reactor coolant inventory compared to its core's thermal power, a large surface area in

Overview of severe accident research at JAERI

International Nuclear Information System (INIS)

Sugimoto, Jun

1999-01-01

Severe accident research at JAERI aims at the confirmation of the safety margin, the quantification of the associated risk, and the evaluation of the effectiveness of the accident management measures of the nuclear power reactors, in accordance with the government five-year nuclear safety research program. JAERI has been conducting a wide range of severe accident research activities both in experiment and analysis, such as melt coolant interactions, fission product behaviors in coolant system, containment integrity and assessment of accident management measures. Molten core/coolant interaction and in-vessel molten coolability have been investigated in ALPHA Program. MUSE experiments in ALPHA Program has been conducted for the precise energy measurement due to steam explosion in melt jet and stratified geometries. In VEGA Program, which aims at FP release from irradiated fuels at high temperature and high pressure under various atmospheric conditions, the facility construction is almost completed. In WIND Program the revaporization of aerosols due to decay heating and also the integrity of the piping from this heat source are being investigated. Code development activities are in progress for an integrated source term analysis with THALES, fission product behaviors with ART, steam explosion with JASMINE, and in-vessel debris behaviors with CAMP. The experimental analyses and reactor application have made progress by participating international standard problem and code comparison exercises, along with the use of introduced codes, such as SCDAP/RELAP5 and MELCOR. The outcome of the severe accident research will be utilized for the evaluation of more reliable severe accident scenarios, detailed implementation of the accident management measures, and also for the future reactor development, basically through the sophisticated use of verified analytical tools. (author)

Predictions of structural integrity of steam generator tubes under normal operating, accident, and severe accident conditions

International Nuclear Information System (INIS)

Majumdar, S.

1996-09-01

Available models for predicting failure of flawed and unflawed steam generator tubes under normal operating, accident, and severe accident conditions are reviewed. Tests conducted in the past, though limited, tended to show that the earlier flow-stress model for part-through-wall axial cracks overestimated the damaging influence of deep cracks. This observation is confirmed by further tests at high temperatures as well as by finite element analysis. A modified correlation for deep cracks can correct this shortcoming of the model. Recent tests have shown that lateral restraint can significantly increase the failure pressure of tubes with unsymmetrical circumferential cracks. This observation is confirmed by finite element analysis. The rate-independent flow stress models that are successful at low temperatures cannot predict the rate sensitive failure behavior of steam generator tubes at high temperatures. Therefore, a creep rupture model for predicting failure is developed and validated by tests under varying temperature and pressure loading expected during severe accidents

Hydrogen behavior in a large-dry pressurized water reactor containment building during a severe accident

International Nuclear Information System (INIS)

Hsu Wensheng; Chen Hungpei; Hung Zhenyu; Lin Huichen

2014-01-01

Following severe accidents in nuclear power plants, large quantities of hydrogen may be generated after core degradation. If the hydrogen is transported from the reactor vessel into the containment building, an explosion might occur, which might threaten the integrity of the building; this can ultimately cause the release of radioactive materials. During the Fukushima Daiichi nuclear accident in 2011, the primary containment structures remained intact but contaminated fragments broke off the secondary containment structures, which disrupted mitigation activities and triggered subsequent explosions. Therefore, the ability to predict the behavior of hydrogen after severe accidents may facilitate the development of effective nuclear reactor accident management procedures. The present study investigated the behavior of hydrogen in a large-dry pressurized water reactor (PWR). The amount of hydrogen produced was calculated using the Modular Accident Analysis Program. The hydrogen transport behavior and the effect of the explosion on the PWR containment building were simulated using the Flame Acceleration Simulator. The simulation results showed that the average hydrogen volume fraction is approximately 7% in the containment building and that the average temperature is 330 K. The maximum predicted pressure load after ignition is 2.55 bar, which does not endanger the structural integrity of the containment building. The results of this investigation indicate that the hydrogen mitigation system should be arranged on both the upper and lower parts of the containment building to reduce the impact of an explosion. (author)

Development of Severe Accident Containment Analysis Package

Energy Technology Data Exchange (ETDEWEB)

Park, Chang-Hwan; Kim, Dong-Min; Seo, Jea-Uk; Lee, Dea-Young; Park, Soon-Ho; Lee, Jae-Gwon; Lee, Jin-Yong; Lee, Byung-Chul [FNC Technology Co., Yongin (Korea, Republic of)

2016-10-15

In safety viewpoint, the pressure and temperature of the containment is the important parameters, of course, the local hydrogen concentration is also the parameter of the major concern because of its flammability and the risk of the detonation. In addition, there are possibilities of occurrence of other relevant phenomena following the reactor core melting such as DCH(direct containment heating) due to HPME(high pressure melt ejection), steam explosion due to fuel-coolant interaction in the reactor cavity and molten core concrete interaction at the late stage. It is important to predict the containment responses during a severe accident by a reasonable accuracy for establishing of effective mitigation strategies and preparation of the safety features required. In this paper, the overview of the SACAP development status is presented. SACAP is developed so as to be able to analyze, so called, Ex-Vessel severe accident phenomena including thermal-hydraulics, combustible gas burn, direct containment heating, steam explosion and molten core-concrete interaction. At the parallel time, SACAP and In-Vessel analysis module named CSPACE are processed for integration through MPI communication coupling. Development of the integrated severe accident analysis code system will be completed in following one year to make the code revision zero to be released.

Severe accident testing of electrical penetration assemblies

International Nuclear Information System (INIS)

Clauss, D.B.

1989-11-01

This report describes the results of tests conducted on three different designs of full-size electrical penetration assemblies (EPAs) that are used in the containment buildings of nuclear power plants. The objective of the tests was to evaluate the behavior of the EPAs under simulated severe accident conditions using steam at elevated temperature and pressure. Leakage, temperature, and cable insulation resistance were monitored throughout the tests. Nuclear-qualified EPAs were produced from D. G. O'Brien, Westinghouse, and Conax. Severe-accident-sequence analysis was used to generate the severe accident conditions (SAC) for a large dry pressurized-water reactor (PWR), a boiling-water reactor (BWR) Mark I drywell, and a BWR Mark III wetwell. Based on a survey conducted by Sandia, each EPA was matched with the severe accident conditions for a specific reactor type. This included the type of containment that a particular EPA design was used in most frequently. Thus, the D. G. O'Brien EPA was chosen for the PWR SAC test, the Westinghouse was chosen for the Mark III test, and the Conax was chosen for the Mark I test. The EPAs were radiation and thermal aged to simulate the effects of a 40-year service life and loss-of-coolant accident (LOCA) before the SAC tests were conducted. The design, test preparations, conduct of the severe accident test, experimental results, posttest observations, and conclusions about the integrity and electrical performance of each EPA tested in this program are described in this report. In general, the leak integrity of the EPAs tested in this program was not compromised by severe accident loads. However, there was significant degradation in the insulation resistance of the cables, which could affect the electrical performance of equipment and devices inside containment at some point during the progression of a severe accident. 10 refs., 165 figs., 16 tabs

MELCOR assessment of sequential severe accident mitigation actions under SGTR accident

International Nuclear Information System (INIS)

Choi, Wonjun; Jeon, Joongoo; Kim, Nam Kyung; Kim, Sung Joong

2017-01-01

The representative example of the severe accident studies using the severe accident code is investigation of effectiveness of developed severe accident management (SAM) strategy considering the positive and adverse effects. In Korea, some numerical studies were performed to investigate the SAM strategy using various severe accident codes. Seo et.al performed validation of RCS depressurization strategy and investigated the effect of severe accident management guidance (SAMG) entry condition under small break loss of coolant accident (SBLOCA) without safety injection (SI), station blackout (SBO), and total loss of feed water (TLOFW) scenarios. The SGTR accident with the sequential mitigation actions according to the flow chart of SAMG was simulated by the MELCOR 1.8.6 code. Three scenariospreventing the RPV failure were investigated in terms of fission product release, hydrogen risk, and the containment pressure. Major conclusions can be summarized as follows: (1) According to the flow chart of SAMG, RPV failure can be prevented depending on the method of RCS depressurization. (2) To reduce the release of fission product during the injecting into SGs, a temporary opening of SDS before the injecting into SGs was suggested. These modified sequences of mitigation actions can reduce the release of fission product and the adverse effect of SDS.

Development of highly reliable power and communication system for essential instruments under severe accidents in NPP

Energy Technology Data Exchange (ETDEWEB)

Choi, Bo Hwan; Jang, Gi Chan; Shin, Sung Min; Kang, Hyun Gook; Rim, Chun Taek [Dept. of Nuclear and Quantum Engineering, Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of); Lee, Soo Ill [I and C Group, Korea Hydro and Nuclear Power Co., Ltd, Central Research Institute, Daejeon (Korea, Republic of)

2016-10-15

This article proposes a highly reliable power and communication system that guarantees the protection of essential instruments in a nuclear power plant under a severe accident. Both power and communication lines are established with not only conventional wired channels, but also the proposed wireless channels for emergency reserve. An inductive power transfer system is selected due to its robust power transfer characteristics under high temperature, high pressure, and highly humid environments with a large amount of scattered debris after a severe accident. A thermal insulation box and a glass-fiber reinforced plastic box are proposed to protect the essential instruments, including vulnerable electronic circuits, from extremely high temperatures of up to 627 .deg. C and pressure of up to 5 bar. The proposed wireless power and communication system is experimentally verified by an inductive power transfer system prototype having a dipole coil structure and prototype Zigbee modules over a 7-m distance, where both the thermal insulation box and the glass-fiber reinforced plastic box are fabricated and tested using a high-temperature chamber. Moreover, an experiment on the effects of a high radiation environment on various electronic devices is conducted based on the radiation test having a maximum accumulated dose of 27 Mrad.

Development of Highly Reliable Power and Communication System for Essential Instruments Under Severe Accidents in NPP

Directory of Open Access Journals (Sweden)

Bo Hwan Choi

2016-10-01

Full Text Available This article proposes a highly reliable power and communication system that guarantees the protection of essential instruments in a nuclear power plant under a severe accident. Both power and communication lines are established with not only conventional wired channels, but also the proposed wireless channels for emergency reserve. An inductive power transfer system is selected due to its robust power transfer characteristics under high temperature, high pressure, and highly humid environments with a large amount of scattered debris after a severe accident. A thermal insulation box and a glass-fiber reinforced plastic box are proposed to protect the essential instruments, including vulnerable electronic circuits, from extremely high temperatures of up to 627°C and pressure of up to 5 bar. The proposed wireless power and communication system is experimentally verified by an inductive power transfer system prototype having a dipole coil structure and prototype Zigbee modules over a 7-m distance, where both the thermal insulation box and the glass-fiber reinforced plastic box are fabricated and tested using a high-temperature chamber. Moreover, an experiment on the effects of a high radiation environment on various electronic devices is conducted based on the radiation test having a maximum accumulated dose of 27 Mrad.

Development of highly reliable power and communication system for essential instruments under severe accidents in NPP

International Nuclear Information System (INIS)

Choi, Bo Hwan; Jang, Gi Chan; Shin, Sung Min; Kang, Hyun Gook; Rim, Chun Taek; Lee, Soo Ill

2016-01-01

This article proposes a highly reliable power and communication system that guarantees the protection of essential instruments in a nuclear power plant under a severe accident. Both power and communication lines are established with not only conventional wired channels, but also the proposed wireless channels for emergency reserve. An inductive power transfer system is selected due to its robust power transfer characteristics under high temperature, high pressure, and highly humid environments with a large amount of scattered debris after a severe accident. A thermal insulation box and a glass-fiber reinforced plastic box are proposed to protect the essential instruments, including vulnerable electronic circuits, from extremely high temperatures of up to 627 .deg. C and pressure of up to 5 bar. The proposed wireless power and communication system is experimentally verified by an inductive power transfer system prototype having a dipole coil structure and prototype Zigbee modules over a 7-m distance, where both the thermal insulation box and the glass-fiber reinforced plastic box are fabricated and tested using a high-temperature chamber. Moreover, an experiment on the effects of a high radiation environment on various electronic devices is conducted based on the radiation test having a maximum accumulated dose of 27 Mrad

Accident management for severe accidents

International Nuclear Information System (INIS)

Bari, R.A.; Pratt, W.T.; Lehner, J.; Leonard, M.; Disalvo, R.; Sheron, B.

1988-01-01

The management of severe accidents in light water reactors is receiving much attention in several countries. The reduction of risk by measures and/or actions that would affect the behavior of a severe accident is discussed. The research program that is being conducted by the US Nuclear Regulatory Commission focuses on both in-vessel accident management and containment and release accident management. The key issues and approaches taken in this program are summarized. 6 refs

Insights from Severe Accident Analyses for Verification of VVER SAMG

Energy Technology Data Exchange (ETDEWEB)

Gaikwad, A. J.; Rao, R. S.; Gupta, A.; Obaidurrahaman, K., E-mail: avinashg@aerb.gov.in [Nuclear Safety Analysis Division, Atomic Energy Regulatory Board, Mumbai (India)

2014-10-15

The severe accident analyses of simultaneous rupture of all four steam lines (case-a), simultaneous occurrence of LOCA with SBO (case-b) and Station blackout (case-c) were performed with the computer code ASTEC V2r2 for a typical VVER-1000. The results obtained will be used for verification of sever accident provisions and Severe Accident Management Guidelines (SAMG). Auxiliary feed water and emergency core cooling systems are modelled as boundary conditions. The ICARE module is used to simulate the reactor core, which is divided into five radial regions by grouping similarly powered fuel assemblies together. Initially, CESAR module computes thermal hydraulics in primary and secondary circuits. As soon as core uncovery begins, the ICARE module is actuated based on certain parameters, and after this, ICARE module computes the thermal hydraulics in the core, bypass, downcomer and the lower plenum. CESAR handles the remaining components in the primary and secondary loops. CPA module is used to simulate the containment and to predict the thermal-hydraulic and hydrogen behaviour in the containment. The accident sequences were selected in such a way that they cover low/high pressure and slow/fast core damage progression events. Events simulated included slow progression events with high pressure and fast accident progression with low primary pressure. Analysis was also carried out for the case of SBO with the opening of the PORVs when core exit temperature exceeds certain value as part of SAMG. Time step sensitivity study was carried out for LOCA with SBO. In general the trends and magnitude of the parameters are as expected. The key results of the above analyses are presented in this paper. (author)

Vaporization of structural materials in severe accidents

International Nuclear Information System (INIS)

Lorenz, R.A.

1982-01-01

Vaporized structural materials form the bulk of aerosol particles that can transport fission products in severe LWR accidents. As part of the Severe Accident Sequence Analysis (SASA) program at Oak Ridge National Laboratory, a model has been developed based on a mass transport coefficient to describe the transport of materials from the surface of a molten pool. In many accident scenarios, the coefficient can be calculated from existing correlations for mass transfer by natural convection. Data from SASCHA fuel melting tests (Karlsruhe, Germany) show that the partial pressures of many of the melt components (Fe, Cr, Co, Mn, Sn) required for the model can be calculated from the vapor pressures of the pure species and Raoult's law. These calculations indicate much lower aerosol concentrations than reported in previous studies

Fuel behaviour in the case of severe accidents and potential ATF designs. Fuel Behavior in Severe Accidents and Potential Accident Tolerance Fuel Designs

International Nuclear Information System (INIS)

Cheng, Bo

2013-01-01

This presentation reviews the conditions of fuel rods under severe loss of coolant conditions, approaches that may increase coping time for plant operators to recover, requirements of advanced fuel cladding to increase tolerance in accident conditions, potential candidate alloys for accident-tolerant fuel cladding and a novel design of molybdenum (Mo) -based fuel cladding. The current Zr-alloy fuel cladding will lose all its mechanical strength at 750-800 deg. C, and will react rapidly with high-pressure steam, producing significant hydrogen and exothermic heat at 700-1000 deg. C. The metallurgical properties of Zr make it unlikely that modifications of the Zr-alloy will improve the behaviour of Zr-alloys at temperatures relevant to severe accidents. The Mo-based fuel cladding is designed to (1) maintain fuel rod integrity, and reduce the release rate of hydrogen and exothermic heat in accident conditions at 1200-1500 deg. C. The EPRI research has thus far completed the design concepts, demonstration of feasibility of producing very thin wall (0.2 mm) Mo tubes. The feasibility of depositing a protective coating using various techniques has also been demonstrated. Demonstration of forming composite Mo-based cladding via mechanical reduction has been planned

A study on the development of framework and supporting tools for severe accident management

International Nuclear Information System (INIS)

Chang, Hyun Sop

1996-02-01

Through the extensive research on severe accidents, knowledge on severe accident phenomenology has constantly increased. Based upon such advance, probabilistic risk studies have been performed for some domestic plants to identify plant-specific vulnerabilities to severe accidents. Severe accident management is a program devised to cover such vulnerabilities, and leads to possible resolution of severe accident issues. This study aims at establishing severe accident management framework for domestic nuclear power plants where severe accident management program is not yet established. Emphasis is given to in-vessel and ex-vessel accident management strategies and instrumentation availability for severe accident management. Among the various strategies investigated, primary system depressurization is found to be the most effective means to prevent high pressure core melt scenarios. During low pressure core melt sequences, cooling of in-vessel molten corium through reactor cavity flooding is found to be effective. To prevent containment failure, containment filtered venting is found to be an effective measure to cope with long-term and gradual overpressurization, together with appropriate hydrogen control measure. Investigation of the availability of Yonggwang 3 and 4 instruments shows that most of instruments essential to severe accident management lose their desired functions during the early phase of severe accident progression, primarily due to the environmental condition exceeded ranges of instruments. To prevent instrument failure, a wider range of instruments are recommended to be used for some severe accident management strategies such as reactor cavity flooding. Severe accidents are generally known to accompany a number of complex phenomena and, therefore, it is very beneficial when severe accident management personnel is aided by appropriately designed supporting systems. In this study, a support system for severe accident management personnel is developed

Thermal Load Analysis of Multilayered Corium in the Lower Head of Reactor Pressure Vessel during Severe Accident

Energy Technology Data Exchange (ETDEWEB)

Whang, Seok Won; Park, Hyun Sun [POSTECH, Pohang (Korea, Republic of); Hwang, Tae Suk [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

2014-05-15

In-Vessel Retention (IVR) is one of the severe accident management strategies to terminate or mitigate the severe accident which is also called 'core-melt accident'. The reactor vessel would be cooled by flooding the cavity with water. The molten core mixture is divided into two or three layers due to the density difference. Light metal layer which contains Fe and Zr is on the oxide layer which is consist of UO{sub 2} and ZrO{sub 2}. Heavy metal layer which contains U, Fe and Zr is located under the oxide layer. In oxide layer, the crust which is solidified material is formed along the boundary. The assessment of IVR for nuclear power plant has been conducted with lumped parameter method by Theofanous, Rempe and Esmaili. In this paper, the numerical analysis was performed and verified with the Esmaili's work to analyze thermal load of multilayered corium in pressurized reactor vessel and also to examine the condition of in-vessel corium characteristic before the vessel failure that lead to ex-vessel severe accident progression for example, ex-vessel debris bed cooling. The in-vessel coolability analysis for several scenarios is conducted for the plant which has higher power than AP1000. Two sensitivity analyses are conducted, the first is emissivity of light metal layer and the second is the heat transfer coefficient correlations of oxide layer. The effect of three layered system also investigated. In this paper, the numerical analysis was performed and verified with Esmaili's model to analyze thermal load of multilayered corium in pressurized reactor vessel. For two layered system, thermal load was analyzed according to the severe accident scenarios, emissivity of the light metal layer and heat transfer correlations of the.

Effect of Spray System on Fission Product Distribution in Containment During a Severe Accident in a Two-Loop Pressurized Water Reactor

Directory of Open Access Journals (Sweden)

Mehdi Dehjourian

2016-08-01

Full Text Available The containment response during the first 24 hours of a low-pressure severe accident scenario in a nuclear power plant with a two-loop Westinghouse-type pressurized water reactor was simulated with the CONTAIN 2.0 computer code. The accident considered in this study is a large-break loss-of-coolant accident, which is not successfully mitigated by the action of safety systems. The analysis includes pressure and temperature responses, as well as investigation into the influence of spray on the retention of fission products and the prevention of hydrogen combustion in the containment.

Severe accident sequences simulated at the Grand Gulf Nuclear Station

International Nuclear Information System (INIS)

Carbajo, J.J.

1999-01-01

Different severe accident sequences employing the MELCOR code, version 1.8.4 QK, have been simulated at the Grand Gulf Nuclear Station (Grand Gulf). The postulated severe accidents simulated are two low-pressure, short-term, station blackouts; two unmitigated small-break (SB) loss-of-coolant accidents (LOCAs) (SBLOCAs); and one unmitigated large LOCA (LLOCA). The purpose of this study was to calculate best-estimate timings of events and source terms for a wide range of severe accidents and to compare the plant response to these accidents

Application of the accident management information needs methodology to a severe accident sequence

International Nuclear Information System (INIS)

Ward, L.W.; Hanson, D.J.; Nelson, W.R.; Solberg, D.E.

1989-01-01

The U.S. Nuclear Regulatory Commission (NRC) is conducting an Accident Management Research Program that emphasizes the application of severe accident research results to enhance the capability of plant operating personnel to effectively manage severe accidents. A methodology to identify and assess the information needs of the operating staff of a nuclear power plant during a severe accident has been developed as part of the research program designed to resolve this issue. The methodology identifies the information needs of the plant personnel during a wide range of accident conditions, the existing plant measurements capable of supplying these information needs and what, if any minor additions to instrument and display systems would enhance the capability to manage accidents, known limitations on the capability of these measurements to function properly under the conditions that will be present during a wide range of severe accidents, and areas in which the information systems could mislead plant personnel. This paper presents an application of this methodology to a severe accident sequence to demonstrate its use in identifying the information which is available for management of the event. The methodology has been applied to a severe accident sequence in a Pressurized Water Reactor with a large dry containment. An examination of the capability of the existing measurements was then performed to determine whether the information needs can be supplied

Severe accident phenomena

International Nuclear Information System (INIS)

Jokiniemi, J.; Kilpi, K.; Lindholm, I.; Maekynen, J.; Pekkarinen, E.; Sairanen, R.; Silde, A.

1995-02-01

Severe accidents are nuclear reactor accidents in which the reactor core is substantially damaged. The report describes severe reactor accident phenomena and their significance for the safety of nuclear power plants. A comprehensive set of phenomena ranging from accident initiation to containment behaviour and containment integrity questions are covered. The report is based on expertise gained in the severe accident assessment projects conducted at the Technical Research Centre of Finland (VTT). (49 refs., 32 figs., 12 tabs.)

Validation of severe accident management guidance for the wolsong plants

International Nuclear Information System (INIS)

Park, S. Y.; Jin, Y. H.; Kim, S. D.; Song, Y. M.

2006-01-01

Full text: Full text: The severe accident management(SAM) guidance has been developed for the Wolsong nuclear power plants in Korea. The Wolsong plants are 700MWe CANDU-type reactors with heavy water as the primary coolant, natural uranium-fueled pressurized, horizontal tubes, surrounded by heavy water moderator inside a horizontal calandria vessel. The guidance includes six individual accident management strategies: (1) injection into primary heat transport system (2) injection into calandria vessel (3) injection into calandria vault (4) reduction of fission product release (5) control of reactor building condition (6) reduction of reactor building hydrogen. The paper provides the approaches to validate the SAM guidance. The validation includes the evaluation of:(l) effectiveness of accident management strategies, (2) performance of mitigation systems or components, (3) calculation aids, (4) strategy control diagram, and (5) interface with emergency operation procedure and with radiation emergency plan. Several severe accident sequences with high probability is selected from the plant specific level 2 probabilistic safety analysis results for the validation of SAM guidance. Afterward, thermal hydraulic and severe accident phenomenological analyses is performed using ISAAC(Integrated Severe Accident Analysis Code for CANDU Plant) computer program. Furthermore, the experiences obtained from a table-top-drill is also discussed

Severe accident source term reassessment

International Nuclear Information System (INIS)

Hazzan, M.J.; Gardner, R.; Warman, E.A.; Jacobs, S.B.

1987-01-01

This paper summarizes the status of the reassessment of severe reactor accident source terms, which are defined as the quantity, type, and timing of fission product releases from such accidents. Concentration is on the major results and conclusions of analyses with modern methods for both pressurized water reactors (PWRs) and boiling water reactors (BWRs), and the special case of containment bypass. Some distinctions are drawn between analyses for PWRs and BWRs. In general, the more the matter is examined, the consequences, or probability of serious consequences, seem to be less. (author)

Design features of ACR in severe accident mitigation

International Nuclear Information System (INIS)

Shapiro, H.; Krishnan, V.S.; Santamaura, P.; Lekakh, B.; Blahnik, C.

2007-01-01

New reactor designs require the evaluation of design alternatives to reduce the radiological risk by preventing severe accidents or by limiting releases from the plant in the event of such accidents. The Advanced CANDU Reactor TM (ACR TM ) design has provisions to prevent and mitigate severe accidents. This paper describes key ACR design features for severe accident mitigation. It provides a high-level overview of the findings to date. Several design provisions have not yet been finalized or decided, but the designers are keenly aware of the SAM concepts and their requirements. The active heat sinks for 'vessels' (i.e., the fuel channels, the calandria vessel, the calandria end-shields and the calandria vault) are all amply capable of dissipating the severe accident heat loads. These heat sinks are designed to be operable under severe accident environmental conditions; however, their operability is yet to be confirmed by assessments. The active heat sinks for the various process vessels are 'backed up' by passive heat sinks (i.e., steaming plus water make-up from the RWS). The supply side of passive heat sinks is simple, rugged, and not vulnerable to failures of plant systems. The importance of the steam relief side is recognized, and the adequate relief capacity will be provided. The passive heat sinks will give the SAM more than 1 day (likely several days) to diagnose the accident and to establish the ultimate heat sinks. The spray system for containment pressure suppression is designed for high reliability and has ample capacity to ensure low containment leakage without external intervention, after which time alternative supply to the sprays can be brought on line manually. The sprays are backed up by the LACs which are assessed for operability following a severe accident. The strong ACR containment will provide a long time of completely passive protection for any severe accident at decay power. Its characteristics are not prone to catastrophic failures. The

Modelling and analysis of severe accidents for VVER-1000 reactors

International Nuclear Information System (INIS)

Tusheva, Polina

2012-01-01

Accident conditions involving significant core degradation are termed severe accidents /IAEA: NS-G-2.15/. Despite the low probability of occurrence of such events, the investigation of severe accident scenarios is an important part of the nuclear safety research. Considering a hypothetical core melt down scenario in a VVER-1000 light water reactor, the early in-vessel phase focusing on the thermal-hydraulic phenomena, and the late in-vessel phase focusing on the melt relocation into the reactor pressure vessel (RPV) lower head, are investigated. The objective of this work is the assessment of severe accident management procedures for VVER-1000 reactors, i.e. the estimation of the maximum period of time available for taking appropriate measures and particular decisions by the plant personnel. During high pressure severe accident sequences it is of prime importance to depressurize the primary circuit in order to allow for effective injection from the emergency core cooling systems and to avoid reactor pressure vessel failure at high pressure that could cause direct containment heating and subsequent challenge to the containment structure. Therefore different accident management measures were investigated for the in-vessel phase of a hypothetical station blackout accident using the severe accident code ASTEC, the mechanistic code ATHLET and the multi-purpose code system ANSYS. The analyses performed on the PHEBUS ISP-46 experiment, as well as simulations of small break loss of coolant accident and station blackout scenarios were used to contribute to the validation and improvement of the integral severe accident code ASTEC. Investigations on the applicability and the effectiveness of accident management procedures in the preventive domain, as well as detailed analyses on the thermal-hydraulic phenomena during the early in-vessel phase of a station blackout accident have been performed with the mechanistic code ATHLET. The results of the simulations show, that the

Severe accident management: a summary of the VAHTI and ROIMA projects

International Nuclear Information System (INIS)

Sairanen, R.

1998-01-01

Two severe accident research projects: 'Severe Accident Management' (VAHTI), 1994-96 and 'Reactor Accidents' Phenomena and Simulation (ROIMA) 1997-98. have been conducted at VTT Energy within the RETU research programme. The main objective was to assist the severe accident management programmes of the Finnish nuclear power plants. The projects had several subtopics. These included thermal hydraulic validation of the APROS code, studies of failure mode of the BWR pressure vessel, investigation of core melt progression within a BWR pressure vessel, containment phenomena, development of a computerised severe accident training tool, and aerosol behaviour experiments. The last topic is summarised by another paper in the seminar. The projects have met the objectives set at the project commencement. Calculation tools have been developed and validated suitable for analyses of questions specific for the Finnish plants. Experimental fission product data have been produced that can be used to validate containment aerosol codes. The tools and results have been utilised in plant assessments. One of the main achievements has been the computer code PASULA for analysis of interactions between core melt and pressure vessel. The code has been applied to pressure vessel penetration analysis. The results have shown the importance of the nozzle construction. Modelling possibilities have recently improved by addition of a creep and porous debris models. Cooling of a degraded BWR core has been systematically studied as joint Nordic projects with a set of severe accident codes. Estimates for coolable conditions have been provided. Recriticality due to reflooding of a damaged core has been evaluated. (orig.)

Factors affecting the integrity of PWR pressure vessels during overcooling accidents

International Nuclear Information System (INIS)

Cheverton, R.D.

1983-01-01

The reactor pressure vessel in a pressurized water reactor is normally subjected to temperatures and pressures that preclude propagation of sharp, crack-like defects that might exist in the wall of the vessel. However, if certain postulated accidents, referred to as overcooling accidents, were to occur, the pressure vessel could be subjected to severe thermal shock while the pressure is substantial. As a result, vessels containing high concentrations of copper and nickel, which enhance radiation embrittlement, may possess a potential for extensive propagation of preexistent inner-surface flaws prior to the vessel's normal end of life. A fracture-mechanics analysis for a typical postulated accident and also related thermal-shock experiments indicate that very shallow surface flaws that extend through the cladding into the base material could propagate. This is of particular concern because shallow flaws appear to be the most probable and presumably are the most difficult to detect

Thermal hydraulics of CANDU severe accident analysis

International Nuclear Information System (INIS)

Negut, Gheorghe; Catana, Alexandru; Prisecaru, Ilie; Dupleac, Daniel

2007-01-01

As interest in severe accident studies has increased in the last years, we have developed a set of simple models to analyze severe accidents in CANDU reactors that should be integrated in the EU codes. The CANDU600 reactor uses natural uranium fuel and heavy water (D 2 O) as both moderator and coolant, with the moderator and coolant in separate systems. We chose to analyze accident development for a LOCA with simultaneous loss of moderator cooling and the loss of emergency core cooling system (ECCS). This type of accident is likely to modify the reactor geometry and will lead to a severe accident development. When the coolant temperatures inside a pressure tube reaches 1000 deg. C, a contact between pressure tube and calandria tube occurs and the residual heat is transferred to the moderator. Due to the lack of cooling, the moderator eventually begins to boil and is expelled, through the calandria vessel relief ducts, into the containment. Therefore the calandria tubes (fuel channels) will be uncovered, then will disintegrate and fall down to the calandria vessel bottom. After all the quantity of moderator is vaporized and expelled, the debris will heat up and eventually boil. The heat accumulated in the molten debris will be transferred through the calandria vessel wall to the shield tank water, which normally surrounds the calandria vessel. The phenomena described above are modelled, analyzed and compared with the available data. The results are encouraging. (authors)

Severe accident assessment. Results of the reactor safety research project VAHTI

International Nuclear Information System (INIS)

Sairanen, R.

1997-10-01

The report provides a summary of the publicly funded nuclear reactor safety research project Severe Accident Management (VAHTI). The project has been conducted at the Technical Research Centre of Finland (VTT) during the years 1994-96. The main objective was to assist the severe accident management programmes of the Finnish nuclear power plants. The project was divided into five work packages: (1) thermal hydraulic validation of the APROS code, (2) core melt progression within a BWR pressure vessel, (3) failure mode of the BWR pressure vessel, (4) Aerosol behaviour experiments, and (5) development of a computerized severe accident training tool

Regulation Plans on Severe Accidents developed by KINS Severe Accident Regulation Preparation TFT

International Nuclear Information System (INIS)

Kim, Kyun Tae; Chung, Ku Young; Na, Han Bee

2016-01-01

Some nuclear power plants in Fukushima Daiichi site had lost their emergency reactor cooling function for long-time so the fuels inside the reactors were molten, and the integrity of containment was damaged. Therefore, large amount of radioactive material was released to environment. Because the social and economic effects of severe accidents are enormous, Korean Government already issued 'Severe Accident Policy' in 2001 which requires nuclear power plant operators to set up 'Quantitative Safety Goal', to do 'Probabilistic Safety Analysis', to install 'Severe Accident Countermeasures' and to make 'Severe Accident Management Plan'. After the Fukushima disaster, a Special Safety Inspection was performed for all operating nuclear power plants of Korea. The inspection team from industry, academia, and research institutes assessed Korean NPPs capabilities to cope with or respond to severe accidents and emergency situation caused by natural disasters such as a large earthquake or tsunami. As a result of the special inspection, about 50 action items were identified to increase the capability to cope with natural disaster and severe accidents. Nuclear Safety Act has been amended to require NPP operators to submit Accident Management Plant as part of operating license application. The KINS Severe Accident Regulation Preparation TFT had first investigated oversea severe accident regulation trend before and after the Fukushima accident. Then, the TFT has developed regulation draft for severe accidents such as Severe accident Management Plans, the required design features for new NPPs to prevent severe accident against multiple failures and beyond-design external events, countermeasures to mitigate severe accident and to keep the integrity of containment, and assessment methodology on safety assessment plan and probabilistic safety assessment

OSSA. A second generation of severe accident management

International Nuclear Information System (INIS)

Sauvage, E.C.; Musoyan, G.; Ducros, V.D.

2009-01-01

Nowadays the severe accident and their management are an integrated part of the new generation of power plants. The EPR, as the third generation of nuclear plants, includes both systems and instrumentation to mitigate a severe accident, but also a new generation of severe accident management guidelines: the OSSA. Severe accident management guidelines are highly dependent on human means available: emergency organization actors, training and knowledge shall be taken in consideration in an innovative way. Their impacts on ergonomy and content of the document lead to a new generation of guidelines with several innovative features. This second generation of severe accident management guidelines was developed in parallel with the PSA level 2, the human reliability analyses, the validation and verification process, the severe accident simulator progresses. By taking in consideration this variety of input the OSSA were developed in a user aspect orientation. For example in the OSSA a larger responsibility is given to the operational crew to better support the technical support group evaluation. Their existing knowledge of the plant and of the systems and instrumentation is used. This collaboration work implies a strong communication tool that has been developed to enhance the permanent communication within the emergency organization, but although to ensure the main up-to-date information for evaluation will be available where required. The entry condition is based on a strong and stand alone diagnostic for all plant states, that uses in particular a curve of core exit temperature as a function of primary pressure for a fixed core cladding temperature, or its equivalent in term of containment conditions. It ensures relatively consistent core conditions on entry. A first criterion for ultimate final primary depressurization is provided, ensuring all attempts to reflood the core with the available means have been ensured before the OSSA entry condition is reached. This

Control room habitability during severe accidents

International Nuclear Information System (INIS)

Siu, R.P.

1989-01-01

The requirements for protection of control room personnel against radiation hazards are specified in 10CFR50, Appendix A, GDC 19. The conventional approach involves a mechanistic evaluation of the radiation doses to control room personnel during design-basis accidents. In this study, an assessment of control room habitability during severe accidents is conducted. The potential levels of radiation hazards to control room personnel are evaluated in terms of both magnitude and probability of occurrence. The expected values for the probabilities of exceeding GDC-19 limits and the cumulative probability distributions of control room doses are determined. In this study, a pressurized water reactor with a large dry containment has been selected for analysis. The types of control rooms evaluated in this study include designs with: (a) filtered local intakes only, (b) filtered recirculation only, (c) filtered local intakes and recirculation, and (d) filtered dual remote intakes and recirculation. From the observations, it is concluded that, except for control room D, all other control room designs may require improvements in order to provide adequate radiation protection during severe accidents, particularly in terms of reducing whole-body gamma doses and skin doses. Potential design improvements include reduction of intake flows for concepts relying on pressurization, reduction in overall leakages, and control room pressurization through the use of bottled air supply

CANDU severe accident analysis

International Nuclear Information System (INIS)

Negut, Gheorghe; Catana, Alexandru; Prisecaru, Ilie; Dupleac, Daniel

2007-01-01

Romania is a EU member since January first 2007. This country faces now new challenges which imply also the nuclear power reactors now in operation. Romania operates since 1996 a CANDU nuclear power reactor and soon will start up a second unit. In EU PWR reactors are mostly operated, so that the Romania's reactors have to meet EU standards. Safety analysis guidelines require to model severe accidents for reactors of this type. Starting from previous studies a thermal-hydraulic model for a degraded CANDU core was developed. The initiating event is assumed to be a LOCA with simultaneous loss of moderator and coolant and the failure of emergency core cooling system (ECCS). This type of accident is likely to modify the reactor geometry and will lead to a severe accident development. When the coolant temperatures inside a pressure tube reaches 1000 deg. C, a contact between pressure tube and calandria tube occurs and the decay heat is transferred to the moderator. Due to the lack of cooling, the moderator eventually begins to boil and is expelled, through the calandria vessel relief ducts, into the containment. Therefore the calandria tubes (fuel channels) uncover, then disintegrate and fall down to the calandria vessel bottom. All the quantity of calandria moderator is vaporized and expelled, the debris will heat up and eventually boil. The heat accumulated in the molten debris will be transferred through the calandria vessel wall to the shield water tank surrounding the calandria vessel. The thermal hydraulics phenomena described above are modeled, analyzed and compared with the existing data. (authors)

Regulation Plans on Severe Accidents developed by KINS Severe Accident Regulation Preparation TFT

Energy Technology Data Exchange (ETDEWEB)

Kim, Kyun Tae; Chung, Ku Young; Na, Han Bee [KINS, Daejeon (Korea, Republic of)

2016-05-15

Some nuclear power plants in Fukushima Daiichi site had lost their emergency reactor cooling function for long-time so the fuels inside the reactors were molten, and the integrity of containment was damaged. Therefore, large amount of radioactive material was released to environment. Because the social and economic effects of severe accidents are enormous, Korean Government already issued 'Severe Accident Policy' in 2001 which requires nuclear power plant operators to set up 'Quantitative Safety Goal', to do 'Probabilistic Safety Analysis', to install 'Severe Accident Countermeasures' and to make 'Severe Accident Management Plan'. After the Fukushima disaster, a Special Safety Inspection was performed for all operating nuclear power plants of Korea. The inspection team from industry, academia, and research institutes assessed Korean NPPs capabilities to cope with or respond to severe accidents and emergency situation caused by natural disasters such as a large earthquake or tsunami. As a result of the special inspection, about 50 action items were identified to increase the capability to cope with natural disaster and severe accidents. Nuclear Safety Act has been amended to require NPP operators to submit Accident Management Plant as part of operating license application. The KINS Severe Accident Regulation Preparation TFT had first investigated oversea severe accident regulation trend before and after the Fukushima accident. Then, the TFT has developed regulation draft for severe accidents such as Severe accident Management Plans, the required design features for new NPPs to prevent severe accident against multiple failures and beyond-design external events, countermeasures to mitigate severe accident and to keep the integrity of containment, and assessment methodology on safety assessment plan and probabilistic safety assessment.

Considerations of severe accidents in the design of Korean Next Generation Reactor

International Nuclear Information System (INIS)

Dong Wook Jerng; Choong Sup Byun

1998-01-01

The severe accident is one of the key issues in the design of Korean Next Generation Reactor (KNGR) which is an evolutionary type of pressurized water reactor. As IAEA recommends in TECDOC-801, the design objective of KNGR with regard to safety is provide a sound technical basis by which an imminent off-site emergency response to any circumstance could be practically unnecessary. To implement this design objective, probabilistic safety goals were established and design requirements were developed for systems to mitigate severe accidents. The basic approach of KNGR to address severe accidents is firstly prevent severe accidents by reinforcing its capability to cope with the design basis accidents (DBA) and further with some accidents beyond DBAs caused by multiple failures, and secondly mitigate severe accidents to ensure the retention of radioactive materials in the containment by providing mean to maintain the containment integrity. For severe accident mitigation, KNGR principally takes the concept of ex-vessel corium cooling. To implement this concept, KNGR is equipped with a large cavity and cavity flooding system connected to the in-containment refueling water storage tank. Other major systems incorporated in KNGR are hydrogen igniters and safety depressurization systems. In addition, the KNGR containment is designed to withstand the pressure and temperature conditions expected during the course of severe accidents. In this paper, the design features and status of system designs related with severe accidents will be presented. Also, R and D activities related to severe accident mitigation system design will be briefly described

Leakage potential through mechanical penetrations in a severe accident environment

International Nuclear Information System (INIS)

Koenig, L.N.

1986-01-01

This paper reviews the findings of an ongoing program, Integrity of Containment Penetrations Under Severe Accident Loads. The program is concerned with the leakage modes as well as the magnitude of leakage through mechanical penetrations in a containment building subject to a severe accident. Seal and gasket tests are used to evaluate the effect of radiation aging, thermal aging, seal geometry, and seal squeeze on seals and gaskets subjected to a hypothesized severe accident. The effects on leakage of the structural response of equipment hatches, personnel airlocks, and drywell heads subjected to severe accident pressures are studied by experiments and analyses. The data gathered during this program will be used to develop methodologies for predicting leakage

Severe accident simulation at Olkiuoto

Energy Technology Data Exchange (ETDEWEB)

Tirkkonen, H.; Saarenpaeae, T. [Teollisuuden Voima Oy (TVO), Olkiluoto (Finland); Cliff Po, L.C. [Micro-Simulation Technology, Montville, NJ (United States)

1995-09-01

A personal computer-based simulator was developed for the Olkiluoto nuclear plant in Finland for training in severe accident management. The generic software PCTRAN was expanded to model the plant-specific features of the ABB Atom designed BWR including its containment over-pressure protection and filtered vent systems. Scenarios including core heat-up, hydrogen generation, core melt and vessel penetration were developed in this work. Radiation leakage paths and dose rate distribution are presented graphically for operator use in diagnosis and mitigation of accidents. Operating on an graphically for operator use in diagnosis and mitigation of accidents. Operating on an 486 DX2-66, PCTRAN-TVO achieves a speed about 15 times faster than real-time. A convenient and user-friendly graphic interface allows full interactive control. In this paper a review of the component models and verification runs are presented.

Computerized accident management support system: development for severe accident management

International Nuclear Information System (INIS)

Garcia, V.; Saiz, J.; Gomez, C.

1998-01-01

The activities involved in the international Halden Reactor Project (HRP), sponsored by the OECD, include the development of a Computerized Accident Management Support System (CAMS). The system was initially designed for its operation under normal conditions, operational transients and non severe accidents. Its purpose is to detect the plant status, analyzing the future evolution of the sequence (initially using the APROS simulation code) and the possible recovery and mitigation actions in case of an accident occurs. In order to widen the scope of CAMS to severe accident management issues, the integration of the MAAP code in the system has been proposed, as the contribution of the Spanish Electrical Sector to the project (with the coordination of DTN). To include this new capacity in CAMS is necessary to modify the system structure, including two new modules (Diagnosis and Adjustment). These modules are being developed currently for Pressurized Water Reactors and Boiling Water REactors, by the engineering of UNION FENOSA and IBERDROLA companies (respectively). This motion presents the characteristics of the new structure of the CAMS, as well as the general characteristics of the modules, developed by these companies in the framework of the Halden Reactor Project. (Author)

High temperature measurements in severe accident experiments on the PLINIUS Platform

International Nuclear Information System (INIS)

Bouyer, V.; Cassiaut-Louis, N.; Fouquart, P.; Journeau, C.; Piluso, P.; Parga, C.

2013-06-01

Severe accident experiments are conducted on the PLINIUS platform in Cadarache, using prototypic corium. During these experiments, it is essential to measure the temperature to know the thermo-physical state of the corium in static and dynamic conditions or to monitor the concrete ablation phenomenology. Temperature in the corium can reach about 2000 to 3000 K. Such aggressive conditions restrict the type of diagnostics that can be employed to do high temperature measurements during the experiments. We employ both non-intrusive (pyrometers) and intrusive (K-type and C-type thermocouples) diagnostics. In this paper, we present the different high temperature measurements techniques and the results that can be obtained in severe accident experiments as corium heating tests and molten core concrete interaction experiments. (authors)

Cost per severe accident as an index for severe accident consequence assessment and its applications

International Nuclear Information System (INIS)

Silva, Kampanart; Ishiwatari, Yuki; Takahara, Shogo

2014-01-01

The Fukushima Accident emphasizes the need to integrate the assessments of health effects, economic impacts, social impacts and environmental impacts, in order to perform a comprehensive consequence assessment of severe accidents in nuclear power plants. “Cost per severe accident” is introduced as an index for that purpose. The calculation methodology, including the consequence analysis using level 3 probabilistic risk assessment code OSCAAR and the calculation method of the cost per severe accident, is proposed. This methodology was applied to a virtual 1,100 MWe boiling water reactor. The breakdown of the cost per severe accident was provided. The radiation effect cost, the relocation cost and the decontamination cost were the three largest components. Sensitivity analyses were carried out, and parameters sensitive to cost per severe accident were specified. The cost per severe accident was compared with the amount of source terms, to demonstrate the performance of the cost per severe accident as an index to evaluate severe accident consequences. The ways to use the cost per severe accident for optimization of radiation protection countermeasures and for estimation of the effects of accident management strategies are discussed as its applications. - Highlights: • Cost per severe accident is used for severe accident consequence assessment. • Assessments of health, economic, social and environmental impacts are included. • Radiation effect, relocation and decontamination costs are important cost components. • Cost per severe accident can be used to optimize radiation protection measures. • Effects of accident management can be estimated using the cost per severe accident

Managing severe reactor accidents. A review and evaluation of our knowledge on reactor accidents and accident management

International Nuclear Information System (INIS)

Gustavsson, Veine

2002-11-01

The report gives a review of the results from the last years research on severe reactor accidents, and an opinion on the possibilities to refine the present strategies for accident management in Swedish and Finnish BWRs. The following aspect of reactor accidents are the major themes of the study: 1. Early pressure relief from hydrogen production; 2. Recriticality in re-flooded, degraded core; 3. Melt-through; 4. Steam explosion after melt-through; 5. Coolability of the melt after after melt-through; 6. Hydrogen fire in the reactor containment; 7. Leaking containment; 8. Hydrogen fire in the reactor building; 9. Long-time developments after a severe accident; 10. Accidents during shutdown for overhaul; 11. Information need for remedial actions. Possibilities for improving the strategies in each of these areas are discussed. The review shows that our knowledge is sufficient in the areas 1, 2, 4, 6, 8. For the other areas, more research is needed

Severe accident testing of a personnel airlock

International Nuclear Information System (INIS)

Clauss, D.B.; Parks, M.B.; Julien, J.T.; Peters, S.W.

1988-01-01

Sandia National Laboratories (Sandia) is investigating the leakage potential of mechanical penetrations as part of a research program on containment integrity under severe accident loads for the U.S. Nuclear Regulatory Commission (NRC). Barnes et al. (1984) and Shackelford et al. (1985) identified leakage from personnel airlocks as an important failure mode of containments subject to severe accident loads. However, these studies were based on relatively simple analysis methods. The complex structural interaction between the door, gasket, and bulkhead in personnel airlocks makes analytical evaluation of leakage difficult. In order to provide data to validate methods for evaluating the leakage potential, a full-size personnel airlock was subject to simulated severe accident loads consisting of pressure and temperature up to 300 psig and 800 degrees F. The test was conducted at Chicago Bridge and Iron under contract to Sandia. The authors provide a detailed report on the test program

Study on structural failure of RPV with geometric discontinuity under severe accident

Energy Technology Data Exchange (ETDEWEB)

Mao, J.F., E-mail: jianfeng-mao@163.com [Institute of Process Equipment and Control Engineering, Zhejiang University of Technology, Hangzhou, Zhejiang 310032 (China); Engineering Research Center of Process Equipment and Re-manufacturing, Ministry of Education (China); Zhu, J.W. [Institute of Process Equipment and Control Engineering, Zhejiang University of Technology, Hangzhou, Zhejiang 310032 (China); Department of Mechanical and Electrical engineering, Huzhou Vocational & Technical College Huzhou, Zhejiang 313000 (China); Bao, S.Y., E-mail: bsy@zjut.edu.cn [Institute of Process Equipment and Control Engineering, Zhejiang University of Technology, Hangzhou, Zhejiang 310032 (China); Engineering Research Center of Process Equipment and Re-manufacturing, Ministry of Education (China); Luo, L.J. [Institute of Process Equipment and Control Engineering, Zhejiang University of Technology, Hangzhou, Zhejiang 310032 (China); Gao, Z.L. [Institute of Process Equipment and Control Engineering, Zhejiang University of Technology, Hangzhou, Zhejiang 310032 (China); Engineering Research Center of Process Equipment and Re-manufacturing, Ministry of Education (China)

2016-10-15

Highlights: • The RPV failure is investigated in depth under severe accident. • The creep and plastic damage are the major contributor to RPV failure. • A elastic core is found at the midpoint of the highly-eroded region. • Weakest location has some ‘accommodating’ quality to prevent ductile tearing. • The internal pressure is critical for the determination of structural failure. - Abstract: A severe accident management strategy known as ‘in-vessel retention (IVR)’ is widely adopted in most of advanced nuclear power plants. The IVR mitigation is assumed to be able to arrest the degraded melting core and maintain the structural integrity of reactor pressure vessel (RPV) within a prescribed period of time. This traditional concept of IVR without consideration of internal pressure effect wasn’t challenged until the occurrence of Fukushima accident on 2011, which showed that the structural behavior had not been appropriately assessed, and a certain pressure (up to 8.0 MPa) still existed inside the RPV. Accordingly, the paper tries to address the related issue on whether lower head (LH) integrity can be maintained, when the LH is subjected to the thermal-mechanical loads created during such a severe accident. Because of the presence of the high temperature melt (∼1300 °C) on the inside of RPV, some local material is melted down to create a unique RPV with geometric discontinuity, while the outside of RPV submerged in cavity water will remain in nucleate boiling (at ∼150 °C). Therefore, the failure mechanisms of RPV can span a wide range of structural behaviors, such as melt-through, creep damage, plastic yielding as well as thermal expansion. Through meticulous investigation, it is found that the RPV failure is mainly caused by creep and plasticity, especially for the inside of highly-eroded region. The elastic core (or layer) is found to exist in the proximity of mid-section of the highly-eroded wall. However, the elastic core is squeezed into

Analysis of hot leg natural circulation under station blackout severe accident

International Nuclear Information System (INIS)

Deng Jian; Cao Xuewu

2007-01-01

Under severe accidents, natural circulation flows are important to influence the accident progression and result in a pressurized water reactor (PWR). In a station blackout accident with no recovery of steam generator (SG) auxiliary feedwater (TMLB' severe accident scenario), the hot leg countercurrent natural circulation flow is analyzed by using a severe-accident code, to better understand its potential impacts on the creep-rupture timing among the surge line, the hot leg; and SG tubes. The results show that the natural circulation may delay the failure time of the hot leg. The recirculation ratio and the hot mixing factor are also calculated and discussed. (authors)

Development of high-performance monitoring system under severe accident condition

International Nuclear Information System (INIS)

Takeuchi, Tomoaki; Tsuchiya, Kunihiro; Ishihara, Masahiro; Komanome, H.; Miura, K.

2017-01-01

A research and development of a monitoring system for NPPs situations even during severe accidents have been performed. The R and D consists of the three objectives. The major findings are briefly summarized in the followings: 1) Radiation-resistant monitoring camera. The image sensor with the photogate and three transistors was found to be advantageous in terms of dark current and sensitivity. In addition, radiation-resistant optical parts and signal circuits were successfully fabricated. The results suggested that the monitoring camera system with 10 6 Gy in radiation resistance was possible. 2) Radiation-resistant in-water wireless transmission system. A two-dimensional LED matrix with 10 6 Gy in radiation resistance and a camera were used as the transmission devices. The results of the in-water transmission tests suggested that stable wireless transmission between 5 m distance was possible even with bubble, turbidity, or obstacles. 3) Heat-resistant signal cable. In order to develop a cable that can transmit the data inside reactor pressure vessels, heat-proof tests were performed for candidate metallic sheath materials of mineral insulation (MI) cables. The results indicated MI cables which can be used at 1000degC in air were possible. These results indicate the feasibility of the monitoring system even during severe accidents. (author)

Options for management of containment integrity during severe accident in Indian PHWR

International Nuclear Information System (INIS)

Sharma, Sanjeev Kr.; Bhartia, D.K.; Mohan, N.; Nair, Suma R.

2015-01-01

Severe accident progressions have the potential to raise the containment pressure beyond the design pressure of the structure. Although the load withstanding capability of the containment structure has been assessed to be substantially higher than the design pressure of the structure (typically 2 times of design pressure), it is possible that a few components of Containment System may degrade leading to excessive release of radioactive fission gases at ground level. Additionally, possible cracks in the concrete of the containment at high pressure may aggravate the release at ground level. Over and above, maintaining high containment pressure high for a longer period increases the ground level release due to leakage from the containment, which effect on dose might be high. For maintaining the Integrity of the Containment, containment pressure can be reduced by either energy management system such as removing the heat from the calandria vault (CVWC) water by using CV water heat exchanger intermittently or reliving the containment atmosphere either through Primary Containment Controlled Discharge (PCCD) or Containment Filtered Venting System (CFVS). Further, it is necessary that these provisions must be initiated below design pressure. This paper presents the analysis for the containment depressurization by using CVWC system restored, manual opening of (PCCD) line and operation of CFVS during the progressions of the accident

Joint research project WASA-BOSS: Further development and application of severe accident codes. Assessment and optimization of accident management measures. Project B: Accident analyses for pressurized water reactors with the application of the ATHLET-CD code; Verbundprojekt WASA-BOSS: Weiterentwicklung und Anwendung von Severe Accident Codes. Bewertung und Optimierung von Stoerfallmassnahmen. Teilprojekt B: Druckwasserreaktor-Stoerfallanalysen unter Verwendung des Severe-Accident-Codes ATHLET-CD

Energy Technology Data Exchange (ETDEWEB)

Jobst, Matthias; Kliem, Soeren; Kozmenkov, Yaroslav; Wilhelm, Polina

2017-02-15

Within the framework of the project an ATHLET-CD input deck for a generic German PWR of type KONVOI has been created. This input deck was applied to the simulation of severe accidents from the accident categories station blackout (SBO) and small-break loss-of-coolant accidents (SBLOCA). The complete accident transient from initial event at full power until the damage of reactor pressure vessel (RPV) is covered and all relevant severe accident phenomena are modelled: start of core heat up, fission product release, melting of fuel and absorber material, oxidation and release of hydrogen, relocation of molten material inside the core, relocation to the lower plenum, damage and failure of the RPV. The model has been applied to the analysis of preventive and mitigative accident management measures for SBO and SBLOCA transients. Therefore, the measures primary side depressurization (PSD), injection to the primary circuit by mobile pumps and for SBLOCA the delayed injection by the cold leg hydro-accumulators have been investigated and the assumptions and start criteria of these measures have been varied. The time evolutions of the transients and time margins for the initiation of additional measures have been assessed. An uncertainty and sensitivity study has been performed for the early phase of one SBO scenario with PSD (until the start of core melt). In addition to that, a code -to-code comparison between ATHLET-CD and the severe accident code MELCOR has been carried out.

Design study on dose evaluation method for employees at severe accident

International Nuclear Information System (INIS)

Yoshida, Yoshitaka; Irie, Takashi; Kohriyama, Tamio; Kudo, Seiichi; Nishimura, Kazuya

2002-01-01

If a severe accident occurs in a pressurized water reactor plant, it is required to estimate dose values of operators engaged in emergency such as accident management, repair of failed parts. However, it might be difficult to measure radiation dose rate during the progress of an accident, because radiation monitors are not always installed in areas where the emergency activities are required. In this study, we analyzed the transport of radioactive materials in case of a severe accident, investigated a method to obtain radiation dose rate in the plant from estimated radioactive sources, made up a prototype analyzing system from this design study, and then evaluated its availability. As a result, we obtained the following: (1) A new dose evaluation method was established to predict the radiation dose rate at any point in the plant during a severe accident scenario. (2) This evaluation of total dose including access route and time for emergency activities is useful for estimating radiation dose limit for these employee actions. (3) The radiation dose rate map is effective for identifying high radiation areas and for choosing a route with lower radiation dose rate. (author)

Severe Accident Analysis for Combustible Gas Risk Evaluation inside CFVS

International Nuclear Information System (INIS)

Lee, NaRae; Lee, JinYong; Bang, YoungSuk; Lee, DooYong; Kim, HyeongTaek

2015-01-01

The purpose of this study is to identify the composition of gases discharged into the containment filtered venting system by analyzing severe accidents. The accident scenarios which could be significant with respect to containment pressurization and hydrogen generation are derived and composition of containment atmosphere and possible discharged gas mixtures are estimated. In order to ensure the safety of the public and environment, the ventilation system should be designed properly by considering discharged gas flow rate, aerosol loads, radiation level, etc. One of considerations to be resolved is the risk due to combustible gas, especially hydrogen. Hydrogen can be generated largely by oxidation of cladding and decomposition of concrete. If the hydrogen concentration is high enough and other conditions like oxygen and steam concentration is met, the hydrogen can burn, deflagrate or detonate, which result in the damage the structural components. In particularly, after Fukushima accident, the hydrogen risk has been emphasized as an important contributor threatening the integrity of nuclear power plant during the severe accident. These results will be used to analyze the risk of hydrogen combustion inside the CFVS as boundary conditions. Severe accident simulation results are presented and discussed qualitatively with respect to hydrogen combustion. The hydrogen combustion risk inside of the CFVS has been examined qualitatively by investigating the discharge flow characteristics. Because the composition of the discharge flow to CFVS would be determined by the containment atmosphere, the severe accident progression and containment atmosphere composition have been investigated. Due to PAR operation, the hydrogen concentration in the containment would be decreased until the oxygen is depleted. After the oxygen is depleted, the hydrogen concentration would be increased. As a result, depending on the vent initiation timing (i.e. vent initiation pressure), the important

Severe Accident Analysis for Combustible Gas Risk Evaluation inside CFVS

Energy Technology Data Exchange (ETDEWEB)

Lee, NaRae; Lee, JinYong; Bang, YoungSuk; Lee, DooYong [FNC Technology Co. Ltd., Yongin (Korea, Republic of); Kim, HyeongTaek [KHNP-Central Research Institute, Daejeon (Korea, Republic of)

2015-10-15

The purpose of this study is to identify the composition of gases discharged into the containment filtered venting system by analyzing severe accidents. The accident scenarios which could be significant with respect to containment pressurization and hydrogen generation are derived and composition of containment atmosphere and possible discharged gas mixtures are estimated. In order to ensure the safety of the public and environment, the ventilation system should be designed properly by considering discharged gas flow rate, aerosol loads, radiation level, etc. One of considerations to be resolved is the risk due to combustible gas, especially hydrogen. Hydrogen can be generated largely by oxidation of cladding and decomposition of concrete. If the hydrogen concentration is high enough and other conditions like oxygen and steam concentration is met, the hydrogen can burn, deflagrate or detonate, which result in the damage the structural components. In particularly, after Fukushima accident, the hydrogen risk has been emphasized as an important contributor threatening the integrity of nuclear power plant during the severe accident. These results will be used to analyze the risk of hydrogen combustion inside the CFVS as boundary conditions. Severe accident simulation results are presented and discussed qualitatively with respect to hydrogen combustion. The hydrogen combustion risk inside of the CFVS has been examined qualitatively by investigating the discharge flow characteristics. Because the composition of the discharge flow to CFVS would be determined by the containment atmosphere, the severe accident progression and containment atmosphere composition have been investigated. Due to PAR operation, the hydrogen concentration in the containment would be decreased until the oxygen is depleted. After the oxygen is depleted, the hydrogen concentration would be increased. As a result, depending on the vent initiation timing (i.e. vent initiation pressure), the important

Design study on dose evaluation method for employees at severe accident

Energy Technology Data Exchange (ETDEWEB)

Yoshida, Yoshitaka; Irie, Takashi; Kohriyama, Tamio [Institute of Nuclear Safety Systems Inc., Mihama, Fukui (Japan); Kudo, Seiichi [Mitsubishi Heavy Industries Ltd., Tokyo (Japan); Nishimura, Kazuya [Computer Software Development Co., Ltd., Tokyo (Japan)

2001-09-01

When we assume a severe accident in a nuclear power plant, it is required for rescue activity in the plant, accident management, repair work of failed parts and evaluation of employees to obtain radiation dose rate distribution or map in the plant and estimated dose value for the above works. However it might be difficult to obtain them accurately along the progress of the accident, because radiation monitors are not always installed in the areas where the accident management is planned or the repair work is thought for safety-related equipments. In this work, we analyzed diffusion of radioactive materials in case of a severe accident in a pressurized water reactor plant, investigated a method to obtain radiation dose rate in the plant from estimated radioactive sources, made up a prototype analyzing system by modeling a specific part of components and buildings in the plant from this design study on dose evaluation method for employees at severe accident, and then evaluated its availability. As a result, we obtained the followings: (1) A new dose evaluation method was established to predict the radiation dose rate in any point in the plant during a severe accident scenario. (2) This evaluation of total dose including moving route and time for the accident management and the repair work is useful for estimating radiation dose limit for these actions of the employees. (3) The radiation dose rate map is effective for identifying high radiation areas and for choosing a route with lower radiation dose rate. (author)

Design study on dose evaluation method for employees at severe accident

International Nuclear Information System (INIS)

Yoshida, Yoshitaka; Irie, Takashi; Kohriyama, Tamio; Kudo, Seiichi; Nishimura, Kazuya

2001-01-01

When we assume a severe accident in a nuclear power plant, it is required for rescue activity in the plant, accident management, repair work of failed parts and evaluation of employees to obtain radiation dose rate distribution or map in the plant and estimated dose value for the above works. However it might be difficult to obtain them accurately along the progress of the accident, because radiation monitors are not always installed in the areas where the accident management is planned or the repair work is thought for safety-related equipments. In this work, we analyzed diffusion of radioactive materials in case of a severe accident in a pressurized water reactor plant, investigated a method to obtain radiation dose rate in the plant from estimated radioactive sources, made up a prototype analyzing system by modeling a specific part of components and buildings in the plant from this design study on dose evaluation method for employees at severe accident, and then evaluated its availability. As a result, we obtained the followings: (1) A new dose evaluation method was established to predict the radiation dose rate in any point in the plant during a severe accident scenario. (2) This evaluation of total dose including moving route and time for the accident management and the repair work is useful for estimating radiation dose limit for these actions of the employees. (3) The radiation dose rate map is effective for identifying high radiation areas and for choosing a route with lower radiation dose rate. (author)

CANDU safety under severe accidents

International Nuclear Information System (INIS)

Snell, V.G.; Howieson, J.Q.; Alikhan, S.; Frescura, G.M.; King, F.; Rogers, J.T.; Tamm, H.

1996-01-01

The characteristics of the CANDU reactor relevant to severe accidents are set first by the inherent properties of the design, and second by the Canadian safety/licensing approach. The pressure-tube concept allows the separate, low-pressure, heavy-water moderator to act as a backup heat sink even if there is no water in the fuel channels. Should this also fail, the calandria shell itself can contain the debris, with heat being transferred to the water-filled shield tank around the core. Should the severe core damage sequence progress further, the shield tank and the concrete reactor vault significantly delay the challenge to containment. Furthermore, should core melt lead to containment overpressure, the containment behaviour is such that leaks through the concrete containment wall reduce the possibility of catastrophic structural failure. The Canadian licensing philosophy requires that each accident, together with failure of each safety system in turn, be assessed (and specified dose limits met) as part of the design and licensing basis. In response, designers have provided CANDUs with two independent dedicated shutdown systems, and the likelihood of Anticipated Transients Without Scram is negligible. Probabilistic safety assessment studies have been performed on operating CANDU plants, and on the 4 x 880 MW(e) Darlington station now under construction; furthermore a scoping risk assessment has been done for a CANDU 600 plant. They indicate that the summed severe core damage frequency is of the order of 5 x 10 -6 /year. 95 refs, 3 tabs

CANDU safety under severe accidents

Energy Technology Data Exchange (ETDEWEB)

Snell, V G; Howieson, J Q [Atomic Energy of Canada Ltd. (Canada); Alikhan, S [New Brunswick Electric Power Commission (Canada); Frescura, G M; King, F [Ontario Hydro (Canada); Rogers, J T [Carleton Univ., Ottawa, ON (Canada); Tamm, H [Atomic Energy of Canada Ltd. (Canada). Whiteshell Research Lab.

1996-12-01

The characteristics of the CANDU reactor relevant to severe accidents are set first by the inherent properties of the design, and second by the Canadian safety/licensing approach. The pressure-tube concept allows the separate, low-pressure, heavy-water moderator to act as a backup heat sink even if there is no water in the fuel channels. Should this also fail, the calandria shell itself can contain the debris, with heat being transferred to the water-filled shield tank around the core. Should the severe core damage sequence progress further, the shield tank and the concrete reactor vault significantly delay the challenge to containment. Furthermore, should core melt lead to containment overpressure, the containment behaviour is such that leaks through the concrete containment wall reduce the possibility of catastrophic structural failure. The Canadian licensing philosophy requires that each accident, together with failure of each safety system in turn, be assessed (and specified dose limits met) as part of the design and licensing basis. In response, designers have provided CANDUs with two independent dedicated shutdown systems, and the likelihood of Anticipated Transients Without Scram is negligible. Probabilistic safety assessment studies have been performed on operating CANDU plants, and on the 4 x 880 MW(e) Darlington station now under construction; furthermore a scoping risk assessment has been done for a CANDU 600 plant. They indicate that the summed severe core damage frequency is of the order of 5 x 10{sup -6}/year. 95 refs, 3 tabs.

Desktop Severe Accident Graphic Simulator Module for CANDU6 : PSAIS

International Nuclear Information System (INIS)

Park, S. Y.; Song, Y. M.

2015-01-01

The ISAAC ((Integrated Severe Accident Analysis Code for CANDU Plant) code is a system level computer code capable of performing integral analyses of potential severe accident progressions in nuclear power plants, whose main purpose is to support a Level 2 probabilistic safety assessment or severe accident management strategy developments. The code has the capability to predict a severe accident progression by modeling the CANDU6- specific systems and the expected physical phenomena based on the current understanding of the unique accident progressions. The code models the sequence of accident progressions from a core heatup, pressure tube/calandria tube rupture after an uncovery from inside and outside, a relocation of the damaged fuel to the bottom of the calandria, debris behavior in the calandria, corium quenching after a debris relocation from the calandria to the calandria vault and an erosion of the calandria vault concrete floor, a hydrogen burn, and a reactor building failure. Along with the thermal hydraulics, the fission product behavior is also considered in the primary system as well as in the reactor building

Occupational Radiation Protection in Severe Accident Management

International Nuclear Information System (INIS)

2015-01-01

As an early response to the Fukushima Daiichi NPP accident, the Information System on Occupational Exposure (ISOE) Bureau decided to focus on the following issues as an initial response of the joint program after having direct communications with the Japanese official participants in April 2011: - Management of high radiation area worker doses: It has been decided to make available the experience and information from the Chernobyl accident in terms of how emergency worker / responder doses were legally and practically managed, - Personal protective equipment for highly-contaminated areas: It was agreed to collect information about the types of personnel protective equipment and other equipment (e.g. air bottles, respirators, air-hoods or plastic suits, etc.), as well as high-radiation area worker dosimetry use (e.g. type, number and placement of dosimetry) for different types of emergency and high-radiation work situations. Detailed information was collected on dose criteria which are used for emergency workers /responders and their basis, dose management criteria for high dose/dose rate areas, protective equipment which is recommended for emergency workers / responders, recommended individual monitoring procedures, and any special requirement for assessment from the ISOE participating nuclear utilities and regulatory authorities and made available for Japanese utilities. With this positive response of the ISOE official participants and interest in the situation in Fukushima, the Expert Group on Occupational Radiation Protection in Severe Accident Management (EG-SAM) was established by the ISOE Management Board in May 2011. The overall objective of the EG-SAM is to contribute to occupational exposure management (providing a view on management of high radiation area worker doses) within the Fukushima plant boundary with the ISOE participants and to develop a state-of-the-art ISOE report on best radiation protection management practices for proper radiation

Analysis of Hydrogen Control Strategy Using Igniter during Severe Accident

International Nuclear Information System (INIS)

Lee, Sung Bok; Kim, Hyeong Taek; Lee, Keo Hyoung

2008-01-01

The Severe Accident Management Guidelines (SAMGs) for the operating pressurized water reactor (PWR) have been completed within 2006. Among the SAMG strategies, mitigation-07 is the most important strategy for managing a severe accident of a PWR in order to reduce containment hydrogen. The fastest way to reduce the containment hydrogen concentration is to intentionally ignite the hydrogen. For this strategy, igniters exist in Optimized Power Reactor 1000 (OPR 1000) to burn hydrogen for a severe accident. For using the igniters during a severe accident, the adverse effects such as the explosion of the hydrogen mixture should be considered for containment integrity. However, an applicable discrimination method to activate the igniters does not exist, so that the hydrogen control strategy using the igniters cannot be chosen during a severe accident. Thus, this study focused on suggesting an applicable discrimination method to carry out the strategy of using the igniters. In this study, the specific plant used for this analysis is Ulchin Unit 5 and 6, OPR 1000 plant, in Korea

Safety against releases in severe accidents. Final report

International Nuclear Information System (INIS)

Lindholm, I.; Berg, Oe.; Nonboel, E.

1997-12-01

The work scope of the RAK-2 project has involved research on quantification of the effects of selected severe accident phenomena for Nordic nuclear power plants, development and testing of a computerised accident management support system and data collection and description of various mobile reactors and of different reactor types existing in the UK. The investigations of severe accident phenomena focused mainly on in-vessel melt progression, covering a numerical assessment of coolability of a degraded BWR core, the possibility and consequences of a BWR reactor to become critical during reflooding and the core melt behavior in the reactor vessel lower plenum. Simulant experiments were carried out to investigate lower head hole ablation induced by debris discharge. In addition to the in-vessel phenomena, a limited study on containment response to high pressure melt ejection in a BWR and a comparative study on fission product source term behaviour in a Swedish PWR were performed. An existing computerised accident management support system (CAMS) was further developed in the area of tracking and predictive simulation, signal validation, state identification and user interface. The first version of a probabilistic safety analysis module was developed and implemented in the system. CAMS was tested in practice with Barsebaeck data in a safety exercise with the Swedish nuclear authority. The descriptions of the key features of British reactor types, AGR, Magnox, FBR and PWR were published as data reports. Separate reports were issued also on accidents in nuclear ships and on description of key features of satellite reactors. The collected data were implemented in a common Nordic database. (au)

SEVERE ACCIDENT ISSUES RAISED BY THE FUKUSHIMA ACCIDENT AND IMPROVEMENTS SUGGESTED

OpenAIRE

SONG, JIN HO; KIM, TAE WOON

2014-01-01

This paper revisits the Fukushima accident to draw lessons in the aspect of nuclear safety considering the fact that the Fukushima accident resulted in core damage for three nuclear power plants simultaneously and that there is a high possibility of a failure of the integrity of reactor vessel and primary containment vessel. A brief review on the accident progression at Fukushima nuclear power plants is discussed to highlight the nature and characteristic of the event. As the severe accide...

Integral thermal model of severe accident dynamics of NPP with containment

International Nuclear Information System (INIS)

Arutyunyan, R.V.; Bol'shov, L.A.; Vasil'ev, A.D.; Kamennov, G.P.

1991-01-01

An analytical model of the interaction of reactor core remains with concrete during severe accidents at nuclear power plants is considered. Time dependences of side and radial concrete melting are plotted. Time dependences of containment atmosphere temperature and pressure during a severe accident at nuclear power plants are investigated analytically and numerically. The sensitivity of the results to the coefficient values in the problem is studied within the range of their concertainty. The Kaverna-1 is described. The results of modelling a severe NPP accident which have been obtained using the Kaverna-1 package are presented

Experiments on natural circulation during PWR severe accidents and their analysis

International Nuclear Information System (INIS)

Sehgal, B.R.; Stewart, W.A.; Sha, W.T.

1988-01-01

Buoyancy-induced natural circulation flows will occur during the early-part of PWR high pressure accident scenarios. These flows affect several key parameters; in particular, the course of such accidents will most probably change due to local failures occurring in the primary coolant system (CS) before substantial core degradation. Natural circulation flow patterns were measured in a one-seventh scale PWR PCS facility at Westinghouse RandD laboratories. The measured flow and temperature distributions are report in this paper. The experiments were analyzed with the COMMIX code and good agreement was obtained between data and calculations. 10 refs., 8 figs., 2 tabs

Severe accident behavior

International Nuclear Information System (INIS)

Denning, R.S.

1986-01-01

The purpose of this paper is to provide an overview of severe accident behavior. The term source term is defined and a brief history of the regulatory use of source term is presented. The processes in severe accidents in light water reactors are described with particular emphasis on the relationships between accident thermal-hydraulics and chemistry. Those factors which have the greatest impact on predicted source terms are identified. Design differences between plants that affect source term estimation are also described. The principal unresolved issues are identified that are the focus of ongoing research and debate in the technical community

Strategies for the prevention and mitigation of severe accidents

International Nuclear Information System (INIS)

Ader, C.; Heusener, G.; Snell, V.G.

1999-01-01

The currently operating nuclear power plants have, in general, achieved a high level of safety, as a result of design philosophies that have emphasized concepts such as defense-in-depth. This type of an approach has resulted in plants that have robust designs and strong containments. These designs were later found to have capabilities to protect the public from severe accidents (accidents more severe than traditional design basis in which substantial damage is done to the reactor core). In spite of this high level of safety, it has also been recognized that future plants need to be designed to achieve an enhanced level of safety, in particular with respect to severe accidents. This has led both regulatory authorities and utilities to develop guidance and/or requirements to guide plant designers in achieving improved severe accident performance through prevention and mitigation. The considerable research programs initiated after the TMI-2 accident have provided a large body of technical data, analytical methods, and the expertise necessary to provide for an understanding of a range of severe accident phenomena. This understanding of the ways severe accidents can progress and challenge containments, combined with the wide use of probabilistic safety assessments, have provided designers of evolutionary water cooled reactors opportunities to develop designs that minimize the challenges to the plant and to the public from severe accidents, including the development of accident management strategies intended to further reduce the risk of severe accidents. This paper describes some of the recent progress made in the understanding of severe accidents and related safety assessment methodology and how this knowledge has supported the incorporation of features into representative evolutionary designs that will prevent or mitigate many of the severe accident challenges present in current plants. (author)

Thermal Hydraulic design parameters study for severe accidents using neural networks

Energy Technology Data Exchange (ETDEWEB)

Roh, Chang Hyun; Chang, Soon Heung [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of); Chang, Keun Sun [Sunmoon University, Asan (Korea, Republic of)

1998-12-31

To provide the information on severe accident progression is very important for advanced or new type of nuclear power plant (NPP) design. A parametric study, therefore, was performed to investigate the effect of thermal hydraulic design parameters on severe accident progression of pressurized water reactors (PWRs). Nine parameters, which are considered important in NPP design or severe accident progression, were selected among the various thermal hydraulic design parameters. The backpropagation neural network (BPN) was used to determine parameters, which might more strongly affect the severe accident progression, among nine parameters. For training, different input patterns were generated by the latin hypercube sampling (LHS) technique and then different target patterns that contain core uncovery time and vessel failure time were obtained for Young Gwang Nuclear (YGN) Units 3 and 4 using modular accident analysis program (MAAP) 3.0B code. Three different severe accident scenarios, such as two loss of coolant accidents (LOCAs) and station blackout (SBO), were considered in this analysis. Results indicated that design parameters related to refueling water storage tank (RWST), accumulator and steam generator (S/G) have more dominant effects on the progression of severe accidents investigated, compared to the other six parameters. 9 refs., 5 tabs. (Author)

Thermal Hydraulic design parameters study for severe accidents using neural networks

Energy Technology Data Exchange (ETDEWEB)

Roh, Chang Hyun; Chang, Soon Heung [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of); Chang, Keun Sun [Sunmoon University, Asan (Korea, Republic of)

1997-12-31

To provide the information on severe accident progression is very important for advanced or new type of nuclear power plant (NPP) design. A parametric study, therefore, was performed to investigate the effect of thermal hydraulic design parameters on severe accident progression of pressurized water reactors (PWRs). Nine parameters, which are considered important in NPP design or severe accident progression, were selected among the various thermal hydraulic design parameters. The backpropagation neural network (BPN) was used to determine parameters, which might more strongly affect the severe accident progression, among nine parameters. For training, different input patterns were generated by the latin hypercube sampling (LHS) technique and then different target patterns that contain core uncovery time and vessel failure time were obtained for Young Gwang Nuclear (YGN) Units 3 and 4 using modular accident analysis program (MAAP) 3.0B code. Three different severe accident scenarios, such as two loss of coolant accidents (LOCAs) and station blackout (SBO), were considered in this analysis. Results indicated that design parameters related to refueling water storage tank (RWST), accumulator and steam generator (S/G) have more dominant effects on the progression of severe accidents investigated, compared to the other six parameters. 9 refs., 5 tabs. (Author)

Overview of severe accident research at the USNRC

International Nuclear Information System (INIS)

Basu, S.; Ader, C.E.

1999-01-01

This paper summarizes the U.S. Nuclear Regulatory Commission's (USNRC) severe accident research activities, in particular, progress made in the past year toward the resolution and/or improved understanding of a number of severe accident issues. The direct containment heating (DCH) is nearing resolution for Combustion Engineering and Babcock and Wilcox type pressurized water reactors (PWRs) are well as for ice condensers. Additionally, two lower pressure DCH tests were conducted recently at the Sandia National Laboratories (SNL) under the NRC/IPSN/FzK sponsorship to provide data regarding intentional depressurization as an accident management strategy to mitigate DCH loads. In the area of lower head integrity, the experimental program to investigate boiling heat transfer on downward facing curved surfaces with insulation was completed. Finally, the SNL program investigating the creep rupture behavior of the lower head under the combined thermo-mechanical loading was completed recently. Additional lower head experiments at SNL are being planned as an OECD project. During the past year, the USNRC participated in two programs aimed at extending the data base on hydrogen combustion into more prototypic situations. Testing was performed at the Brookhaven National Laboratory (BNL) to investigate detonation transmission at elevated temperatures. In a cooperative program under the sponsorship of NRC/IPSN/FzK, Russian Research Center (RRC) investigated hydrogen combustion issues at large scale at the RUT facility. The experimental program at the SNL to examine the performance of Passive Autocatalytic Recombiners (PARs) was completed also this year. In the fuel-coolant interaction (FCI) area, the experimental work at the Argonne National Laboratory (ANL) to investigate chemical augmentation of FCI energetics was completed as was the experimental work at the University of Wisconsin (UW) involving one-dimensional propagation experiments (similar to KROTOS). The USNRC is

Study on severe accidents and countermeasures for WWER-1000 reactors using the integral code ASTEC

International Nuclear Information System (INIS)

Tusheva, P.; Schaefer, F.; Altstadt, E.; Kliem, S.; Reinke, N.

2011-01-01

The research field focussing on the investigations and the analyses of severe accidents is an important part of the nuclear safety. To maintain the safety barriers as long as possible and to retain the radioactivity within the airtight premises or the containment, to avoid or mitigate the consequences of such events and to assess the risk, thorough studies are needed. On the one side, it is the aim of the severe accident research to understand the complex phenomena during the in- and ex-vessel phase, involving reactor-physics, thermal-hydraulics, physicochemical and mechanical processes. On the other side the investigations strive for effective severe accident management measures. This paper is focused on the possibilities for accident management measures in case of severe accidents. The reactor pressure vessel is the last barrier to keep the molten materials inside the reactor, and thus to prevent higher loads to the containment. To assess the behaviour of a nuclear power plant during transient or accident conditions, computer codes are widely used, which have to be validated against experiments or benchmarked against other codes. The analyses performed with the integral code ASTEC cover two accident sequences which could lead to a severe accident: a small break loss of coolant accident and a station blackout. The results have shown that in case of unavailability of major active safety systems the reactor pressure vessel would ultimately fail. The discussed issues concern the main phenomena during the early and late in-vessel phase of the accident, the time to core heat-up, the hydrogen production, the mass of corium in the reactor pressure vessel lower plenum and the failure of the reactor pressure vessel. Additionally, possible operator's actions and countermeasures in the preventive or mitigative domain are addressed. The presented investigations contribute to the validation of the European integral severe accidents code ASTEC for WWER-1000 type of reactors

Severe Accident Test Station Activity Report

Energy Technology Data Exchange (ETDEWEB)

Pint, Bruce A [ORNL; Terrani, Kurt A [ORNL

2015-06-01

Enhancing safety margins in light water reactor (LWR) severe accidents is currently the focus of a number of international R&D programs. The current UO2/Zr-based alloy fuel system is particularly susceptible since the Zr-based cladding experiences rapid oxidation kinetics in steam at elevated temperatures. Therefore, alternative cladding materials that offer slower oxidation kinetics and a smaller enthalpy of oxidation can significantly reduce the rate of heat and hydrogen generation in the core during a coolant-limited severe accident. In the U.S. program, the high temperature steam oxidation performance of accident tolerant fuel (ATF) cladding solutions has been evaluated in the Severe Accident Test Station (SATS) at Oak Ridge National Laboratory (ORNL) since 2012. This report summarizes the capabilities of the SATS and provides an overview of the oxidation kinetics of several candidate cladding materials. A suggested baseline for evaluating ATF candidates is a two order of magnitude reduction in the steam oxidation resistance above 1000ºC compared to Zr-based alloys. The ATF candidates are categorized based on the protective external oxide or scale that forms during exposure to steam at high temperature: chromia, alumina, and silica. Comparisons are made to literature and SATS data for Zr-based alloys and other less-protective materials.

Management of severe accidents

International Nuclear Information System (INIS)

Jankowski, M.W.

1987-01-01

The definition and the multidimensionality aspects of accident management have been reviewed. The suggested elements in the development of a programme for severe accident management have been identified and discussed. The strategies concentrate on the two tiered approaches. Operative management utilizes the plant's equipment and operators capabilities. The recovery managment concevtrates on preserving the containment, or delaying its failure, inhibiting the release, and on strategies once there has been a release. The inspiration for this paper was an excellent overview report on perspectives on managing severe accidents in commercial nuclear power plants and extending plant operating procedures into the severe accident regime; and by the most recent publication of the International Nuclear Safety Advisory Group (INSAG) considering the question of risk reduction and source term reduction through accident prevention, management and mitigation. The latter document concludes that 'active development of accident management measures by plant personnel can lead to very large reductions in source terms and risk', and goes further in considering and formulating the key issue: 'The most fruitful path to follow in reducing risk even further is through the planning of accident management.' (author)

Management of severe accidents

International Nuclear Information System (INIS)

Jankowski, M.W.

1988-01-01

The definition and the multidimensionality aspects of accident management have been reviewed. The suggested elements in the development of a programme for severe accident management have been identified and discussed. The strategies concentrate on the two tiered approaches. Operative management utilizes the plant's equipment and operators capabilities. The recovery management concentrates on preserving the containment, or delaying its failure, inhibiting the release, and on strategies once there has been a release. The inspiration for this paper was an excellent overview report on perspectives on managing severe accidents in commercial nuclear power plants and extending plant operating procedures into the severe accident regime; and by the most recent publication of the International Nuclear Safety Advisory Group (INSAG) considering the question of risk reduction and source term reduction through accident prevention, management and mitigation. The latter document concludes that active development of accident management measures by plant personnel can lead to very large reductions in source terms and risk, and goes further in considering and formulating the key issue: The most fruitful path to follow in reducing risk even further is through the planning of accident management

Water hammer due to rapid bubble growth at a severe accident

International Nuclear Information System (INIS)

Aya, Izuo; Adachi, Masaki; Shiozaki, Koki; Inasaka, Fujio

2000-01-01

On a severe accident of the light water reactor (LWR), by steam explosion and so forth due to hydrogen formation by water-metal reaction and direct contact of molted core with water, it is presumed that a lot of vapor forms for a short time in water at reactor vessel and under part of containment vessel. This study aims at and carries out, under reference of the conventional study results, experimental elucidation on coherence of water block motion due to rapid bubble growth, proposal on reduction method of water hammering, development of water hammer estimating method in an actual reactor, and proposal for upgrading of reliability on severe accident evaluation. In 1998 fiscal year, an 'Experimental apparatus on water hammering elements on sever accident' simulated rapid bubble growth due to steam explosion by injecting high pressure air into water was produced to carry out its function test. As a result of the carried out function tests, extreme water hammering phenomena were observed, by which validity of establishment on the study objects could be confirmed. (G.K.)

Preliminary safety analysis of the PWR with accident-tolerant fuels during severe accident conditions

International Nuclear Information System (INIS)

Wu, Xiaoli; Li, Wei; Wang, Yang; Zhang, Yapei; Tian, Wenxi; Su, Guanghui; Qiu, Suizheng; Liu, Tong; Deng, Yongjun; Huang, Heng

2015-01-01

Highlights: • Analysis of severe accident scenarios for a PWR fueled with ATF system is performed. • A large-break LOCA without ECCS is analyzed for the PWR fueled with ATF system. • Extended SBO cases are discussed for the PWR fueled with ATF system. • The accident-tolerance of ATF system for application in PWR is illustrated. - Abstract: Experience gained in decades of nuclear safety research and previous nuclear accidents direct to the investigation of passive safety system design and accident-tolerant fuel (ATF) system which is now becoming a hot research point in the nuclear energy field. The ATF system is aimed at upgrading safety characteristics of the nuclear fuel and cladding in a reactor core where active cooling has been lost, and is preferable or comparable to the current UO 2 –Zr system when the reactor is in normal operation. By virtue of advanced materials with improved properties, the ATF system will obviously slow down the progression of accidents, allowing wider margin of time for the mitigation measures to work. Specifically, the simulation and analysis of a large break loss of coolant accident (LBLOCA) without ECCS and extended station blackout (SBO) severe accident are performed for a pressurized water reactor (PWR) loaded with ATF candidates, to reflect the accident-tolerance of ATF

Conclusions on severe accident research priorities

International Nuclear Information System (INIS)

Klein-Heßling, W.; Sonnenkalb, M.; Jacquemain, D.; Clément, B.; Raimond, E.; Dimmelmeier, H.; Azarian, G.; Ducros, G.; Journeau, C.; Herranz Puebla, L.E.; Schumm, A.; Miassoedov, A.; Kljenak, I.; Pascal, G.; Bechta, S.; Güntay, S.; Koch, M.K.; Ivanov, I.; Auvinen, A.; Lindholm, I.

2014-01-01

Highlights: • Estimation of research priorities related to severe accident phenomena. • Consideration of new topics, partly linked to the severe accidents at Fukushima. • Consideration of results of recent projects, e.g. SARNET, ASAMPSA2, OECD projects. - Abstract: The objectives of the SARNET network of excellence are to define and work on common research programs in the field of severe accidents in Gen. II–III nuclear power plants and to further develop common tools and methodologies for safety assessment in this area. In order to ensure that the research conducted on severe accidents is efficient and well-focused, it is necessary to periodically evaluate and rank the priorities of research. This was done at the end of 2008 by the Severe Accident Research Priority (SARP) group at the end of the SARNET project of the 6th Framework Programme of European Commission (FP6). This group has updated this work in the FP7 SARNET2 project by accounting for the recent experimental results, the remaining safety issues as e.g. highlighted by Level 2 PSA national studies and the results of the recent ASAMPSA2 FP7 project. These evaluation activities were conducted in close relation with the work performed under the auspices of international organizations like OECD or IAEA. The Fukushima-Daiichi severe accidents, which occurred while SARNET2 was running, had some effects on the prioritization and definition of new research topics. Although significant progress has been gained and simulation models (e.g. the ASTEC integral code, jointly developed by IRSN and GRS) were improved, leading to an increased confidence in the predictive capabilities for assessing the success potential of countermeasures and/or mitigation measures, most of the selected research topics in 2008 are still of high priority. But the Fukushima-Daiichi accidents underlined that research efforts had to focus still more to improve severe accident management efficiency

Centrifugal Filtration System for Severe Accident Source Term Treatment

Energy Technology Data Exchange (ETDEWEB)

Liu, Shu Chang; Yim, Man Sung [KAIST, Daejeon (Korea, Republic of)

2016-05-15

The objective of this paper is to present the conceptual design of a filtration system that can be used to process airborne severe accident source term. Reactor containment may lose its structural integrity due to over-pressurization during a severe accident. This can lead to uncontrolled radioactive releases to the environment. For preventing the dispersion of these uncontrolled radioactive releases to the environment, several ways to capture or mitigate these radioactive source term releases are under investigation at KAIST. Such technologies are based on concepts like a vortex-like air curtain, a chemical spray, and a suction arm. Treatment of the radioactive material captured by these systems would be required, before releasing to environment. For current filtration systems in the nuclear industry, IAEA lists sand, multi-venturi scrubber, high efficiency particulate arresting (HEPA), charcoal and combinations of the above in NS-G-1-10, 4.143. Most if not all of the requirements of the scenario for applying this technology near the containment of an NPP site and the environmental constraints were analyzed for use in the design of the centrifuge filtration system.

Safety against releases in severe accidents. Final report

Energy Technology Data Exchange (ETDEWEB)

Lindholm, I.; Berg, Oe.; Nonboel, E. [eds.

1997-12-01

The work scope of the RAK-2 project has involved research on quantification of the effects of selected severe accident phenomena for Nordic nuclear power plants, development and testing of a computerised accident management support system and data collection and description of various mobile reactors and of different reactor types existing in the UK. The investigations of severe accident phenomena focused mainly on in-vessel melt progression, covering a numerical assessment of coolability of a degraded BWR core, the possibility and consequences of a BWR reactor to become critical during reflooding and the core melt behavior in the reactor vessel lower plenum. Simulant experiments were carried out to investigate lower head hole ablation induced by debris discharge. In addition to the in-vessel phenomena, a limited study on containment response to high pressure melt ejection in a BWR and a comparative study on fission product source term behaviour in a Swedish PWR were performed. An existing computerised accident management support system (CAMS) was further developed in the area of tracking and predictive simulation, signal validation, state identification and user interface. The first version of a probabilistic safety analysis module was developed and implemented in the system. CAMS was tested in practice with Barsebaeck data in a safety exercise with the Swedish nuclear authority. The descriptions of the key features of British reactor types, AGR, Magnox, FBR and PWR were published as data reports. Separate reports were issued also on accidents in nuclear ships and on description of key features of satellite reactors. The collected data were implemented in a common Nordic database. (au) 39 refs.

Pilot program: NRC severe reactor accident incident response training manual: Severe reactor accident overview

International Nuclear Information System (INIS)

McKenna, T.J.; Martin, J.A.; Miller, C.W.; Hively, L.M.; Sharpe, R.W.; Giitter, J.G.; Watkins, R.M.

1987-02-01

This pilot training manual has been written to fill the need for a general text on NRC response to reactor accidents. The manual is intended to be the foundation for a course for all NRC response personnel. Severe Reactor Accident Overview is the second in a series of volumes that collectively summarize the US Nuclear Regulatory Commission (NRC) emergency response during severe power reactor accidents and provide necessary background information. This volume describes elementary perspectives on severe accidents and accident assesment. Each volume serves, respectively, as the text for a course of instruction in a series of courses. Each volume is accompanied by an appendix of slides that can be used to present this material. The slides are called out in the text

Severe Accident Research Program plan update

International Nuclear Information System (INIS)

1992-12-01

In August 1989, the staff published NUREG-1365, ''Revised Severe Accident Research Program Plan.'' Since 1989, significant progress has been made in severe accident research to warrant an update to NUREG-1365. The staff has prepared this SARP Plan Update to: (1) Identify those issues that have been closed or are near completion, (2) Describe the progress in our understanding of important severe accident phenomena, (3) Define the long-term research that is directed at improving our understanding of severe accident phenomena and developing improved methods for assessing core melt progression, direct containment heating, and fuel-coolant interactions, and (4) Reflect the growing emphasis in two additional areas--advanced light water reactors, and support for the assessment of criteria for containment performance during severe accidents. The report describes recent major accomplishments in understanding the underlying phenomena that can occur during a severe accident. These include Mark I liner failure, severe accident scaling methodology, source term issues, core-concrete interactions, hydrogen transport and combustion, TMI-2 Vessel Investigation Project, and direct containment heating. The report also describes the major planned activities under the SARP over the next several years. These activities will focus on two phenomenological issues (core melt progression, and fuel-coolant interactions and debris coolability) that have significant uncertainties that impact our understanding and ability to predict severe accident phenomena and their effect on containment performance SARP will also focus on severe accident code development, assessment and validation. As the staff completes the research on severe accident issues that relate to current generation reactors, continued research will focus on efforts to independently evaluate the capability of new advanced light water reactor designs to withstand severe accidents

Severe accident analysis methodology in support of accident management

International Nuclear Information System (INIS)

Boesmans, B.; Auglaire, M.; Snoeck, J.

1997-01-01

The author addresses the implementation at BELGATOM of a generic severe accident analysis methodology, which is intended to support strategic decisions and to provide quantitative information in support of severe accident management. The analysis methodology is based on a combination of severe accident code calculations, generic phenomenological information (experimental evidence from various test facilities regarding issues beyond present code capabilities) and detailed plant-specific technical information

Insights into the behavior of LWR steel containment buildings during severe accidents

International Nuclear Information System (INIS)

Clauss, D.B.; Horschel, D.S.; Blejwas, T.E.

1987-01-01

Investigations into the performance of steel containment subject to pressure and temperature greater than their design basis loads are discussed. The timing, mechanism, and location of a containment failure, i.e., release of radioactive materials, have an important impact on the consequences of a severe accident. We review the results of experiments on steel containment models pressurized to failure, on aged and unaged seals subjected to elevated temperature and pressure, and on electrical penetration assemblies tested for leakage. Based on the results, the important features and details of analytical methods that can be used to predict containment performance are identified. Finally, we speculate on the performance of steel containments in severe accident conditions. (orig.)

Evaluation of high-pressure containment buildings for LMFBR's

International Nuclear Information System (INIS)

Armstrong, G.R.

1981-01-01

A study was conducted on the use of High Pressure LMFBR Containment Buildings for 1000 MW(e) LMFBRs. Two principal aspects were investigated: accident consequence mitigation and cost. Two types of hypothetical accidents were analyzed to establish consequence mitigation: melt-through and energetic expulsion. Three Containment Building (CB) design pressures were investigated: 69 kPa (10 psig), 207 kPa (30 psig), and 414 kPa (60 psig). Four types of design structures were analyzed to establish cost: steel, steel with confinement building, reinforced concrete, and prestressed/post-tensioned concrete. Results show that: it is within reason that a high pressure containment for a 1000 MW(e) reactor can be fabricated that will retain its integrity during postulated severe hypothetical accidents, if available measures are taken to reduce or prevent hydrogen production and the cost differential between basic high (414 kPa) and low (69 kPa) pressure containments is $10 x 10 6 or less

Cernavoda CANDU severe accident evaluation

International Nuclear Information System (INIS)

Negut, G.; Marin, A.

1997-01-01

The papers present the activities dedicated to Romania Cernavoda Nuclear Power Plant first CANDU Unit severe accident evaluation. This activity is part of more general PSA assessment activities. CANDU specific safety features are calandria moderator and calandria vault water capabilities to remove the residual heat in the case of severe accidents, when the conventional heat sinks are no more available. Severe accidents evaluation, that is a deterministic thermal hydraulic analysis, assesses the accidents progression and gives the milestones when important events take place. This kind of assessment is important to evaluate to recovery time for the reactor operators that can lead to the accident mitigation. The Cernavoda CANDU unit is modeled for the of all heat sinks accident and results compared with the AECL CANDU 600 assessment. (orig.)

Essential severe accident mitigation measures for operating and future PWR's

Energy Technology Data Exchange (ETDEWEB)

Bittermann, Dietmar; Eckardt, Bernd A.; Lechleuthner, Michael [Framatome ANP GmbH, Erlangen (Germany)

2003-04-01

obtaining realistic information on airborne material in the containment atmosphere, on the conditions of the core and for effective accident management decisions. These new in-situ sampling technology was developed and implemented to avoid the strong deposition errors of iodine and aerosols in conventional pipe extraction systems. The venting system is introduced for operating plants and can also be used for future plants although it is not required for the EPR. The Sliding Pressure Venting System consists mainly of a venturi scrubber unit with integrated high efficient metal fiber filter followed by means for super sonic throttling and operation under the sliding containment pressure conditions. Due to this special design and operation the system dimensions could be kept small in spite of obtaining high retention rates for aerosols of >99.99% and that for molecular iodide is >99.5%. For the EPR additional measures for maintaining the containment integrity are foreseen: {center_dot} use of highly reliable dedicated valves for depressurization which supplement normal bleed valves to eliminate high pressure RPV failure {center_dot} use of a core melt retention device for melt stabilization by means of spreading of the melt within a large compartment adjacent to the reactor pit, followed by flooding, quenching and cooling of the melt from the top and via a bottom cooling structure; {center_dot} use of a dedicated active two-train containment heat removal system which needs to operate not earlier than 12h after start of the accident.

A framework for the assessment of severe accident management strategies

International Nuclear Information System (INIS)

Kastenberg, W.E.; Apostolakis, G.; Dhir, V.K.; Okrent, D.; Jae, M.; Lim, H.; Milici, T.; Park, H.; Swider, J.; Xing, L.; Yu, D.

1992-01-01

Accident management can be defined as the innovative use of existing and or alternative resources, systems and actions to prevent or mitigate a severe accident. Together with risk management (changes in plant operation and/or addition of equipment) and emergency planning (off-site actions), accident management provides an extension of the defense-in-depth safety philosophy for severe accidents. A significant number of probabilistic safety assessments (PSA) have been completed which yield the principal plant vulnerabilities. For each sequence/threat and each combination of strategy there may be several options available to the operator. Each strategy/option involves phenomenological and operational considerations regarding uncertainty. These considerations include uncertainty in key phenomena, uncertainty in operator behavior, uncertainty in system availability and behavior, and uncertainty in available information (i.e., instrumentation). The objective of this project is to develop a methodology for assessing severe accident management strategies given the key uncertainties mentioned above. Based on decision trees and influence diagrams, the methodology is currently being applied to two case studies: cavity flooding in a pressurized water reactor to prevent vessel penetration or failure, and drywell flooding in a boiling water reactor to prevent containment failure

Joint research project WASA-BOSS: Further development and application of severe accident codes. Assessment and optimization of accident management measures. Project B: Accident analyses for pressurized water reactors with the application of the ATHLET-CD code

International Nuclear Information System (INIS)

Jobst, Matthias; Kliem, Soeren; Kozmenkov, Yaroslav; Wilhelm, Polina

2017-02-01

Within the framework of the project an ATHLET-CD input deck for a generic German PWR of type KONVOI has been created. This input deck was applied to the simulation of severe accidents from the accident categories station blackout (SBO) and small-break loss-of-coolant accidents (SBLOCA). The complete accident transient from initial event at full power until the damage of reactor pressure vessel (RPV) is covered and all relevant severe accident phenomena are modelled: start of core heat up, fission product release, melting of fuel and absorber material, oxidation and release of hydrogen, relocation of molten material inside the core, relocation to the lower plenum, damage and failure of the RPV. The model has been applied to the analysis of preventive and mitigative accident management measures for SBO and SBLOCA transients. Therefore, the measures primary side depressurization (PSD), injection to the primary circuit by mobile pumps and for SBLOCA the delayed injection by the cold leg hydro-accumulators have been investigated and the assumptions and start criteria of these measures have been varied. The time evolutions of the transients and time margins for the initiation of additional measures have been assessed. An uncertainty and sensitivity study has been performed for the early phase of one SBO scenario with PSD (until the start of core melt). In addition to that, a code -to-code comparison between ATHLET-CD and the severe accident code MELCOR has been carried out.

Severe accident progression perspectives for Mark I containments based on the IPE results

International Nuclear Information System (INIS)

Lin, C.C.; Lehner, J.R.; Pratt, W.T.; Drouin, M.

1995-01-01

Based on level 2 analyses in IPE (Individual Plant Examination) submittals accident progression, perspectives were obtained for all containment types. These perspectives consisted of insights on containment failure modes, releases therein, and factors responsible for the results. To illustrate the types of perspectives acquired on severe accident progresssion, insights obtained for (BWR) Mark I containments are discussed here. Mark I containments have high strength but small volumes and rely on pressure suppression pools to condense steam released from the reactor coolant system during an accident. Accidents causing structural failure of the drywell shortly after the core debris melts through the reactor vessel were found to be dominant contributors to risk. Importance of individual containment failure mechanisms depends on plant features and in some cases on modeling assumptions; however the following mechanisms were found important: drywell shell melt-through caused by direct contact with core debris and drywell failure caused by rapid pressure/temperature pulses at time of vessel melt-through. Drywell failure caused by gradual pressure/temperature buildup due to gases and steam released during core/concrete interactions is important in some IPEs. In other IPEs vent was an important contributor. However, accidents that bypass containment (eg interfacing systems LOCA)or involve containment isolation failure were not important contributors to the CDF in any of the IPEs for Mark I plants. These accidents are also not important to risk (even though they can involve large fission product release) because their frequencies of occurrence are so much lower than frequencies of early structural failure caused by other accidents that dominate the CDF

Phenomenological uncertainty analysis of early containment failure at severe accident of nuclear power plant

Energy Technology Data Exchange (ETDEWEB)

Lee, Su Won

2011-02-15

The severe accident has inherently significant uncertainty due to wide range of conditions and performing experiments, validation and practical application are extremely difficult because of its high temperature and pressure. Although internal and external researches were put into practice, the reference used in Korean nuclear plants were foreign data of 1980s and safety analysis as the probabilistic safety assessment has not applied the newest methodology. Also, it is applied to containment pressure formed into point value as results of thermal hydraulic analysis to identify the probability of containment failure in level 2 PSA. In this paper, the uncertainty analysis methods for phenomena of severe accident influencing early containment failure were developed, the uncertainty analysis that apply Korean nuclear plants using the MELCOR code was performed and it is a point of view to present the distribution of containment pressure as a result of uncertainty analysis. Because early containment failure is important factor of Large Early Release Frequency(LERF) that is used as representative criteria of decision-making in nuclear power plants, it was selected in this paper among various modes of containment failure. Important phenomena of early containment failure at severe accident based on previous researches were comprehended and methodology of 7th steps to evaluate uncertainty was developed. The MELCOR input for analysis of the severe accident reflected natural circulation flow was developed and the accident scenario for station black out that was representative initial event of early containment failure was determined. By reviewing the internal model and correlation for MELCOR model relevant important phenomena of early containment failure, the uncertainty factors which could affect on the uncertainty were founded and the major factors were finally identified through the sensitivity analysis. In order to determine total number of MELCOR calculations which can

Severe accidents in nuclear reactors

International Nuclear Information System (INIS)

Ohai, Dumitru; Dumitrescu, Iulia; Tunaru, Mariana

2004-01-01

The likelihood of accidents leading to core meltdown in nuclear reactors is low. The consequences of such an event are but so severe that developing and implementing of adequate measures for preventing or diminishing the consequences of such events are of paramount importance. The analysis of major accidents requires sophisticated computation codes but necessary are also relevant experiments for checking the accuracy of the predictions and capability of these codes. In this paper an overview of the severe accidents worldwide with definitions, computation codes and relating experiments is presented. The experimental research activity of severe accidents was conducted in INR Pitesti since 2003, when the Institute jointed the SARNET Excellence Network. The INR activity within SARNET consists in studying scenarios of severe accidents by means of ASTEC and RELAP/SCDAP codes and conducting bench-scale experiments

Severe accident training simulator APROS SA

International Nuclear Information System (INIS)

Raiko, Eerikki; Salminen, Kai; Lundstroem, Petra; Harti, Mika; Routamo, Tomi

2003-01-01

APROS SA is a severe accident training simulator based on the APROS simulation environment. APROS SA has been developed in Fortum Nuclear Services Ltd to serve as a training tool for the personnel of the Loviisa NPP. Training with APROS SA gives the personnel a deeper understanding of the severe accident phenomena and thus it is an important part of the implementation of the severe accident management strategy. APROS SA consists of two parts, a comprehensive Loviisa plant model and an external severe accident model. The external model is an extension to the Loviisa plant model, which allows the simulation to proceed into the severe accident phase. The severe accident model has three submodels: the core melting and relocation model, corium pool model and fission product model. In addition to these, a new thermal-hydraulic solver is introduced to the core region of the Loviisa plant model to replace the more limited APROS thermal-hydraulic solver. The full APROS SA training simulator has a graphical user interface with visualizations of both severe accident management panels at the operator room and the important physical phenomena during the accident. This paper describes the background of the APROS SA training simulator, the severe accident submodels and the graphical user interface. A short description how APROS SA will be used as a training tool at the Loviisa NPP is also given

Use of decision trees for evaluating severe accident management strategies in nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Jae, Moosung [Hanyang Univ., Seoul (Korea, Republic of). Dept. of Nuclerar Engineering; Lee, Yongjin; Jerng, Dong Wook [Chung-Ang Univ., Seoul (Korea, Republic of). School of Energy Systems Engineering

2016-07-15

Accident management strategies are defined to innovative actions taken by plant operators to prevent core damage or to maintain the sound containment integrity. Such actions minimize the chance of offsite radioactive substance leaks that lead to and intensify core damage under power plant accident conditions. Accident management extends the concept of Defense in Depth against core meltdown accidents. In pressurized water reactors, emergency operating procedures are performed to extend the core cooling time. The effectiveness of Severe Accident Management Guidance (SAMG) became an important issue. Severe accident management strategies are evaluated with a methodology utilizing the decision tree technique.

Failure Mode Estimation of Wolsong Unit 1 Containment Building with respect to Severe Accident Condition

International Nuclear Information System (INIS)

Hahm, Dae Gi; Choi, In Kil

2009-01-01

The containment buildings in a nuclear power plant (NPP) are final barriers against the exposure of harmful radiation materials at severe accident condition. Since the accident at Three Mile Island nuclear plant in 1979, it has become necessary to evaluate the internal pressure capacity of the containment buildings for the assessment of the safety of nuclear power plants. According to this necessity, many researchers including Yonezawa et al. and Hu and Lin analyzed the ultimate capacity of prestressed concrete containments subjected to internal pressure which can be occurred at sever accident condition. Especially in Wolsong nuclear power plant, the Unit 1 containment structures were constructed in the late 1970 to early 1980, so that the end of its service life will be reached in near future. Since that the complete decommission and reconstruction of the NPP may cause a huge expenses, an extension of the service time can be a cost-effective alternative. To extend the service time of NPP, an overall safety evaluation of the containment building under severe accident condition should be performed. In this study, we assessed the pressure capacity of Wolsong Unit 1 containment building under severe accident, and estimated the responses at all of the probable critical areas. Based on those results, we found the significant failure modes of Wolsong Unit 1 containment building with respect to the severe accident condition. On the other hand, for the aged NPP, the degradation of their structural performance must also be explained in the procedure of the internal pressure capacity evaluation. Therefore, in this study, we performed a parametric study on the degradation effects and evaluated the internal pressure capacity of Wolsong Unit 1 containment building with considering aging and degradation effects

MELCOR Severe Accident Analysis on the SMART Reactor

International Nuclear Information System (INIS)

Kim, Tae Woon; Jin, Young Ho; Kim, Young In; Kim, Keung Koo; Wang, Ziao; Revankar, Shripad

2014-01-01

A severe accident is analyzed for Korea SMR reactor, SMART. Core melt down sequences are analyzed for SMART reactor core using MELCOR version 1.8.5. MELCOR is developed by Sandia National Laboratory for US NRC for the simulation of severe accidents in nuclear power plants. Two cases are simulated here and compared between them; one is the case for core having 3 concentric rings and the other is the case for core having 5 concentric rings. One inch break LOCA scenario is simulated and compared between these two core models. Time sequences for the thermal hydraulic behaviors of RPV and thermal heatup behaviors of reactor core are explained in graphically. Thermal hydraulic behavior such as the change of pressure, level, mass, and temperature of RPV is explained. Thermal heatup behavior of reactor core such as oxidation of cladding, hydrogen generation, core slumping down to lower plenum, and finally creep rupture of PRV lower head is explained. Engineered safety features such as safety injection systems (SIS), and Passive residual heat removal systems (PHRS), etc. are assumed to be not working. One inch break of severe accident is simulated on Korean SMR (SMART) Integral PWR with MELCOR code version 1.8.5. Core melt progression and lower head failure time is very slow compared to other commercial reactors. Simulation on 3 and 5 radial rings core models gives very similar pattern in core cell failure timings. Other various accident scenarios (for example, SBO in Fukushima) will be tried further. Containment behaviors and source term behaviors in severe accident conditions will be analyzed in future

Method of assessing severe accident management strategies

International Nuclear Information System (INIS)

Kastenberg, W.E.; Apostolakis, G.; Dhir, V.K.; Okrent, D.; Jae, M.; Lim, H.; Milici, T.; Park, H.; Swider, J.; Xing, L.; Yu, D.

1991-01-01

Accident management can be defined as the innovative use of existing and or alternative resources, systems, and actions to prevent or mitigate a severe accident. A significant number of probabilistic safety assessments (PSAs) have been completed that yield the principal plant vulnerabilities. These vulnerabilities can be categorized as (1) dominant sequences with respect to core-melt frequency. (2) dominant sequences with respect to various risk measures. (3) dominant threats that challenge safety functions. (4) dominant threats with respect to failure of safety systems. For each sequence/threat and each combination of strategy, there may be several options available to the operator. Each strategy/option involves phenomenological and operational considerations regarding uncertainty. These considerations include uncertainties in key phenomena, operator behavior, system availability and behavior, and available information. This paper presents a methodology for assessing severe accident management strategies given the key uncertainties delineated at two workshops held at the University of California, Los Angeles. Based on decision trees and influence diagrams, the methodology is currently being applied to two case studies: cavity flooding in a pressurized water reactor (PWR) to prevent vessel penetration or failure, and drywell flooding in a boiling water reactor to prevent vessel and/or containment failure

Severe accident consequence mitigation by filtered containment venting at Canadian nuclear power plants

International Nuclear Information System (INIS)

Lebel, Luke S.; Morreale, Andrew C.; Korolevych, Volodymyr; Brown, Morgan J.; Gyepi-Garbrah, Sam

2017-01-01

Highlights: • Use of filtered containment venting during a severe accident assessed. • Severe accident simulations performed using MAAP-CANDU and ADDAM. • Flow capacity, initiation protocols, efficiency, mass and thermal loading evaluated. • Efficient, robust system drastically reduces accident consequences. - Abstract: Having the capability to use filtered containment venting during a severe nuclear accident can significantly reduce its overall consequences. This study employs the MAAP-CANDU severe accident analysis code and the ADDAM atmospheric dispersion code to study the progression of: an unmitigated station blackout accident at a generic pressurized heavy water reactor, the release of radioactive material into the environment, the subsequent dispersion of the fission products through the atmosphere and the subsequent consequences (evacuation radius). The goal is to evaluate the application of filtered venting as an accident mitigation technology. Several aspects of filtered containment venting system design, like flow capacity, initiation protocols, filter efficiency, mass loading, and thermal loading are considered. An efficient and robust filtered containment venting system can reduce the amount of radiological materials emitted during an accident by 25 times or more, and as a result considerably reduce the off-site consequences of an accident.

An assessment the severe accident equipment survivability for the Korean Next Generation Reactor

International Nuclear Information System (INIS)

Lee, B. C.; Moon, Y. T.; Park, J. W.; Kho, H. J.; Lee, S. W.

1999-01-01

One of the prominent design approaches to cope with the severe accident challenges in the Korean Next Generation Reactor is an assessment of equipment survivability in the severe accident environment at early design stage. In compliance with 10CFR50.34(f) and SECY-93-087, this work addresses that a reasonable level of assurance be provided to demonstrate that sufficient instrumentation and equipment will survive the consequences of a severe accident and will be available so that the operator may recover from and trend severe core damage sequences, including those scenarios which result in 100 percent oxidation of the active fuel cladding. An analytical and systematic approach was used to identify the equipment and instrumentation of safety-function and define severe accident environments including temperature, pressure, humidity, and radiation before and after the reactor vessel breach. As a result, it was concluded that with minor exceptions, existing design basis equipment qualification methods are sufficient to provide a reasonable level of assurance that this equipment will function during a severe accident. Furthermore, supplemental severe accident equipment and instrument procurement requirements were identified. (author)

Severe accidents at nuclear power plants. Their risk assessment and accident management

International Nuclear Information System (INIS)

Abe, Kiyoharu.

1995-05-01

This document is to explain the severe accident issues. Severe Accidents are defined as accidents which are far beyond the design basis and result in severe damage of the core. Accidents at Three Mild Island in USA and at Chernobyl in former Soviet Union are examples of severe accidents. The causes and progressions of the accidents as well as the actions taken are described. Probabilistic Safety Assessment (PSA) is a method to estimate the risk of severe accidents at nuclear reactors. The methodology for PSA is briefly described and current status on its application to safety related issues is introduced. The acceptability of the risks which inherently accompany every technology is then discussed. Finally, provision of accident management in Japan is introduced, including the description of accident management measures proposed for BWRs and PWRs. (author)

Impact of severe accidents on the European pressurized water reactor (ERP) design and layout

International Nuclear Information System (INIS)

Yvon, M.; Lohnert, G.; Lauret, P.; Bittermann, D.

1998-01-01

The purpose of this presentation is to describe the impact of severe accidents on the EPR design and layout. After a summary of the safety requirements specified in accordance with the recommendations expressed by the French and German safety authorities, the main EPR features corresponding to the prevention and the mitigation of severe accidents will be described. Considerations with regard to R and D and cost impacts are also provided

Uncertainties and severe-accident management

International Nuclear Information System (INIS)

Kastenberg, W.E.

1991-01-01

Severe-accident management can be defined as the use of existing and or alternative resources, systems, and actions to prevent or mitigate a core-melt accident. Together with risk management (e.g., changes in plant operation and/or addition of equipment) and emergency planning (off-site actions), accident management provides an extension of the defense-indepth safety philosophy for severe accidents. A significant number of probabilistic safety assessments have been completed, which yield the principal plant vulnerabilities, and can be categorized as (a) dominant sequences with respect to core-melt frequency, (b) dominant sequences with respect to various risk measures, (c) dominant threats that challenge safety functions, and (d) dominant threats with respect to failure of safety systems. Severe-accident management strategies can be generically classified as (a) use of alternative resources, (b) use of alternative equipment, and (c) use of alternative actions. For each sequence/threat and each combination of strategy, there may be several options available to the operator. Each strategy/option involves phenomenological and operational considerations regarding uncertainty. These include (a) uncertainty in key phenomena, (b) uncertainty in operator behavior, (c) uncertainty in system availability and behavior, and (d) uncertainty in information availability (i.e., instrumentation). This paper focuses on phenomenological uncertainties associated with severe-accident management strategies

Severe accidents: in nuclear power plants

International Nuclear Information System (INIS)

1986-01-01

A ''severe'' nuclear accident refers to a reactor accident that could exceed reactor design specifications to such a degree as to prevent cooling of the reactor's core by normal means. This report summarizes the work of a NEA Senior Group of Experts who have studied the potential response of existing light-water reactors to severe accidents and have found that current designs of reactors are far more capable of coping with severe accidents than design specifications would suggest. The report emphasises the specific knowledge and means that can be used for diagnosing a severe accident and for managing its progression in order to prevent or mitigate its consequences

Geographic analysis of road accident severity index in Nigeria.

Science.gov (United States)

Iyanda, Ayodeji E

2018-05-28

Before 2030, deaths from road traffic accidents (RTAs) will surpass cerebrovascular disease, tuberculosis, and HIV/AIDS. Yet, there is little knowledge on the geographic distribution of RTA severity in Nigeria. Accident Severity Index is the proportion of deaths that result from a road accident. This study analysed the geographic pattern of RTA severity based on the data retrieved from Federal Road Safety Corps (FRSC). The study predicted a two-year data from a historic road accident data using exponential smoothing technique. To determine spatial autocorrelation, global and local indicators of spatial association were implemented in a geographic information system. Results show significant clusters of high RTA severity among states in the northeast and the northwest of Nigeria. Hence, the findings are discussed from two perspectives: Road traffic law compliance and poor emergency response. Conclusion, the severity of RTA is high in the northern states of Nigeria, hence, RTA remains a public health concern.

Role of BWR secondary containments in severe accident mitigation: issues and insights from recent analyses

International Nuclear Information System (INIS)

Greene, S.R.

1988-01-01

All commercial boiling water reactor (BWR) plants in the US employ primary containments of the pressure suppression design. These primary containments are surrounded and enclosed by a secondary containment consisting of a reactor building and refueling bay (MK I and MK II designs), a shield building, auxiliary building and fuel building (MK III), or an auxiliary building and enclosure building (Grand Gulf style MK III). Although secondary containment designs are highly plant specific, their purpose is to minimize the ground level release of radioactive material for a spectrum of traditional design basis accidents. While not designed for severe accident mitigation, these secondary containments might also reduce the radiological consequences of severe accidents. This issue is receiving increasing attention due to concerns that BWR MK I primary containment integrity would be lost should a significant mass of molten debris escape the reactor vessel during a severe accident. This paper presents a brief overview of domestic BWR secondary containment designs and highlights plant-specific features that could influence secondary containment severe accident survivability and accident mitigation effectiveness. Current issues surrounding secondary containment performance are discussed, and insights gained from recent ORNL secondary containment studies of Browns Ferry, Peach Bottom, and Shoreham are presented. Areas of significant uncertainty are identified and recommendations for future research are presented

Proceedings of the workshop on operator training for severe accident management and instrumentation capabilities during severe accidents

International Nuclear Information System (INIS)

2001-01-01

to. Though uncertainties still remain in the understanding of some severe accident phenomena, this should not be considered as a de-facto impediment against using simplified models both as operator aids in the course of an accident and as an option of a simulator severe accident mathematical model. These tools, however, should be based on state-of-the-art physics and calibrated using more sophisticated codes. Having the capability for periodic assessment of trends and predictions against real plant parameter evolution, and subsequent correction is also advised for such tools. Being prepared for the unexpected is the major objective pursued in training, especially when capabilities extend into severe accident situations. When training for severe accidents is contemplated, skill-oriented sessions should be emphasized as they allow evaluating operator reactions in highly perturbed situations. However, it is also advised to increase operator awareness in case of severe accident situations through tailored sessions stressing knowledge of basic phenomena involved in degraded situations. Though computer-based training could well prevail in the long run, table-top exercises as currently implemented by many utilities also bring extremely valuable results

Application of high-order uncertainty for severe accident management

International Nuclear Information System (INIS)

Yu, Donghan; Ha, Jaejoo

1998-01-01

The use of probability distribution to represent uncertainty about point-valued probabilities has been a controversial subject. Probability theorists have argued that it is inherently meaningless to be uncertain about a probability since this appears to violate the subjectivists' assumption that individual can develop unique and precise probability judgments. However, many others have found the concept of uncertainty about the probability to be both intuitively appealing and potentially useful. Especially, high-order uncertainty, i.e., the uncertainty about the probability, can be potentially relevant to decision-making when expert's judgment is needed under very uncertain data and imprecise knowledge and where the phenomena and events are frequently complicated and ill-defined. This paper presents two approaches for evaluating the uncertainties inherent in accident management strategies: 'a fuzzy probability' and 'an interval-valued subjective probability'. At first, this analysis considers accident management as a decision problem (i.e., 'applying a strategy' vs. 'do nothing') and uses an influence diagram. Then, the analysis applies two approaches above to evaluate imprecise node probabilities in the influence diagram. For the propagation of subjective probabilities, the analysis uses the Monte-Carlo simulation. In case of fuzzy probabilities, the fuzzy logic is applied to propagate them. We believe that these approaches can allow us to understand uncertainties associated with severe accident management strategy since they offer not only information similar to the classical approach using point-estimate values but also additional information regarding the impact from imprecise input data

Brief account of the effect of overcooling accidents on the integrity of PWR pressure vessels

International Nuclear Information System (INIS)

Cheverton, R.D.

1982-01-01

The occurrence in recent years of several (PWR) accident initiating events that could lead to severe thermal shock to the reactor pressure vessel, and the growing awareness that copper and nickel in the vessel material significantly enhance radiation damage in the vessel, have resulted in a reevaluation of pressure-vessel integrity during postulated overcooling accidents. Analyses indicate that the accidents of concern are those involving both thermal shock and pressure loadings, and that an accident similar to that at Rancho Seco in 1978 could, under some circumstances and at a time late in the normal life of the vessel, result in propagation of preexistent flaws in the vessel wall to the extent that they might completely penetrate the wall. More severe accidents have been postulated that would result in even shorter permissible lifetimes. However, the state-of-the-art fracture-mechanics analysis may contain excessive conservatism, and this possibility is being investigated. Furthermore, there are several remedial measures, such as fuel shuffling, to reduce the damage rate, and vessel annealing, to restore favorable material properties, that may be practical and used if necessary. 5 figures

SAMEX: A severe accident management support expert

International Nuclear Information System (INIS)

Park, Soo-Yong; Ahn, Kwang-Il

2010-01-01

A decision support system for use in a severe accident management following an incident at a nuclear power plant is being developed which is aided by a severe accident risk database module and a severe accident management simulation module. The severe accident management support expert (SAMEX) system can provide the various types of diagnostic and predictive assistance based on the real-time plant specific safety parameters. It consists of four major modules as sub-systems: (a) severe accident risk data base module (SARDB), (b) risk-informed severe accident risk data base management module (RI-SARD), (c) severe accident management simulation module (SAMS), and (d) on-line severe accident management guidance module (on-line SAMG). The modules are integrated into a code package that executes within a WINDOWS XP operating environment, using extensive user friendly graphics control. In Korea, the integrated approach of the decision support system is being carried out under the nuclear R and D program planned by the Korean Ministry of Education, Science and Technology (MEST). An objective of the project is to develop the support system which can show a theoretical possibility. If the system is feasible, the project team will recommend the radiation protection technical support center of a national regulatory body to implement a plant specific system, which is applicable to a real accident, for the purpose of immediate and various diagnosis based on the given plant status information and of prediction of an expected accident progression under a severe accident situation.

A comparison of in-vessel behaviors between SFR and PWR under severe accident

Energy Technology Data Exchange (ETDEWEB)

Park, Sanggil; Cho, Cheon Hwey [ACT Co., Daejeon (Korea, Republic of); Kim, Sang Ji [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

This paper aims to provide an easy guide for experts who know well the severe accident phenomenology of Pressurized Water Reactor (PWR) by comparing both reactor design concepts and in vessel behaviors under a postulated severe accident condition. This study only provides a preliminary qualitative comparison based on available literature. The PWR and SFR in-vessel design concepts and their effects under a postulate severe accident are investigated in this paper. Although this work is a preliminary study to compare the in-vessel behaviors for both PWR and SFR, it seems that there is no possibility to lead a significant core damage in the metal fuel SFR concept. In the oxide fuel SFR, there might be a chance to progress to the severe accident initiators such as the energetic reaction, flow blockage and so on.

Study on confinement function of reactor containment during late phase severe accident

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-08-15

During a severe accident reactor containment integrity is maintained by accident management. However, gas leakage from containment is inevitable after the severe accident. A large amount of hydrogen and rare gases are produced due to core damage or melting. These non-condensable gases cause the containment pressure much higher than atmospheric pressure even after residual heat removal system recovery especially for BWR with smaller containment volume. Besides, iodine confined in water pool is re-evaporated under radiation field. The present study consists of realistic evaluation of fission products source term inside containment, quantitative evaluation of iodine re-evaporation effect and the experimental study of hydrogen treatment in BWR using ammonia production method by catalyst. Activities in fiscal year 2012 are that modification of MELCOR fission product chemical model was done and verified by experimental data, and that effects of CsI on ammonia production rate for Ru catalyst were conducted. (author)

Method for consequence calculations for severe accidents

International Nuclear Information System (INIS)

Nielsen, F.; Thykier-Nielsen, S.; Walmod-Larsen, O.

1986-08-01

This report was commissioned by the Swedish State Power Board, who wanted a method for calculation of radiation doses in the surroundings of nuclear power plants caused by severe accidents. The PLUCON4 code were used for the calculations. A TC-SV-accident at Ringhals 1 wer chosen as example. A transient without shutdown leads to core meltdown through the reactor vessel. The pressure peak at the moment of vessel failure opens a safety valve in the dry well. Meteorolgical data for two years from the Ringhals meteorological tower were analysed to find representative weather situations. As typical weather were chosen Pasquill D with wind speed 8 m/s, and as extreme weather were chosen Pasquill F with wind speed 4.8 m/s. (author)

Severe accident simulation and analysis for a CAREM-like integral nuclear reactor: ex-vessel phase

International Nuclear Information System (INIS)

Caputo, M.; García, J.M.; Giménez, M.; Sánchez, S.

2013-01-01

The main phenomena and processes involved in the progression of a hypothetical nuclear severe accident in an integral type reactor like CAREM are studied, quantifying the most relevant parameters, in order to contribute to the plant design and the development of an appropriate severe accident management program. A computational plant model was developed using Melcor code, including the reactor pressure vessel and the containment. A loss of coolant accident caused by a double guillotine pipe break in the steam dome zone of the pressure vessel (1.5 inches diameter) was simulated. Along this work the analysis were focused in the containment dynamics. As a consequence of the postulated loss of coolant accident the water inventory boils off leading to the core uncovery and fuel heat-up. At high temperatures the zircaloy steam oxidation becomes relevant, with hydrogen generation as one of the reaction products. The hydrogen produced is release into the containment and the possibility of hydrogen combustion in presence of enough oxygen makes relevant the analysis of containment hydrogen distribution. It is assumed that there is not any hydrogen control system. Due to the postulated loss of coolant a big amount of steam and energy is released into the containment, with a consequent fast pressurization of the dry well which makes possible air and steam discharging into the wet well (suppression pool). At the beginning the flow discharged into the pool is mainly composed of air, a non-condensable gas that pressurizes the wet well. After most of the containment air is pushed into the atmosphere wet well the pressurization rate decreases because the flow discharge is mainly composed by steam, which condensates in the pool. Also some other containment pressure peaks were observed as a consequence of hydrogen deflagrations. (author)

Reactor Core Coolability Analysis during Hypothesized Severe Accidents of OPR1000

International Nuclear Information System (INIS)

Lee, Yongjae; Seo, Seungwon; Kim, Sung Joong; Ha, Kwang Soon; Kim, Hwan-Yeol

2014-01-01

Assessment of the safety features over the hypothesized severe accidents may be performed experimentally or numerically. Due to the considerable time and expenditures, experimental assessment is implemented only to the limited cases. Therefore numerical assessment has played a major role in revisiting severe accident analysis of the existing or newly designed power plants. Computer codes for the numerical analysis of severe accidents are categorized as the fast running integral code and detailed code. Fast running integral codes are characterized by a well-balanced combination of detailed and simplified models for the simulation of the relevant phenomena within an NPP in the case of a severe accident. MAAP, MELCOR and ASTEC belong to the examples of fast running integral codes. Detailed code is to model as far as possible all relevant phenomena in detail by mechanistic models. The examples of detailed code is SCDAP/RELAP5. Using the MELCOR, Carbajo. investigated sensitivity studies of Station Black Out (SBO) using the MELCOR for Peach Bottom BWR. Park et al. conduct regulatory research of the PWR severe accident. Ahn et al. research sensitivity analysis of the severe accident for APR1400 with MELCOR 1.8.4. Lee et al. investigated RCS depressurization strategy and developed a core coolability map for independent scenarios of Small Break Loss-of-Coolant Accident (SBLOCA), SBO, and Total Loss of Feed Water (TLOFW). In this study, three initiating cases were selected, which are SBLOCA without SI, SBO, and TLOFW. The initiating cases exhibit the highest probability of transitioning into core damage according to PSA 1 of OPR 1000. The objective of this study is to investigate the reactor core coolability during hypothesized severe accidents of OPR1000. As a representative indicator, we have employed Jakob number and developed JaCET and JaMCT using the MELCOR simulation. Although the RCS pressures for the respective accident scenarios were different, the JaMCT and Ja

NPP Krsko Severe Accident Management Guidelines Implementation

International Nuclear Information System (INIS)

Basic, I.; Krajnc, B.; Bilic-Zabric, T.; Spiler, J.

2002-01-01

Severe Accident Management is a framework to identify and implement the Emergency Response Capabilities that can be used to prevent or mitigate severe accidents and their consequences. The USA NRC has indicated that the development of a licensee plant specific accident management program will be required in order to close out the severe accident regulatory issue (Ref. SECY-88-147). Generic Letter 88-20 ties the Accident management Program to IPE for each plant. The SECY-89-012 defines those actions taken during the course of an accident by the plant operating and technical staff to: 1) prevent core damage, 2) terminate the progress of core damage if it begins and retain the core within the reactor vessel, 3) maintain containment integrity as long as possible, and 4) minimize offsite releases. The subject of this paper is to document the severe accident management activities, which resulted in a plant specific Severe Accident Management Guidelines implementation. They have been developed based on the Krsko IPE (Individual Plant Examination) insights, Generic WOG SAMGs (Westinghouse Owners Group Severe Accident Management Guidances) and plant specific documents developed within this effort. Among the required plant specific actions the following are the most important ones: Identification and documentation of those Krsko plant specific severe accident management features (which also resulted from the IPE investigations). The development of the Krsko plant specific background documents (Severe Accident Plant Specific Strategies and SAMG Setpoint Calculation). Also, paper discusses effort done in the areas of NPP Krsko SAMG review (internal and external ), validation on Krsko Full Scope Simulator (Severe Accident sequences are simulated by MAAP4 in real time) and world 1st IAEA Review of Accident Management Programmes (RAMP). (author)

Monitoring Severe Accidents Using AI Techniques

International Nuclear Information System (INIS)

No, Young Gyu; Kim, Ju Hyun; Na, Man Gyun; Ahn, Kwang Il

2011-01-01

It is very difficult for nuclear power plant operators to monitor and identify the major severe accident scenarios following an initiating event by staring at temporal trends of important parameters. The objective of this study is to develop and verify the monitoring for severe accidents using artificial intelligence (AI) techniques such as support vector classification (SVC), probabilistic neural network (PNN), group method of data handling (GMDH) and fuzzy neural network (FNN). The SVC and PNN are used for event classification among the severe accidents. Also, GMDH and FNN are used to monitor for severe accidents. The inputs to AI techniques are initial time-integrated values obtained by integrating measurement signals during a short time interval after reactor scram. In this study, 3 types of initiating events such as the hot-leg LOCA, the cold-leg LOCA and SGTR are considered and it is verified how well the proposed scenario identification algorithm using the GMDH and FNN models identifies the timings when the reactor core will be uncovered, when CET will exceed 1200 .deg. F and when the reactor vessel will fail. In cases that an initiating event develops into a severe accident, the proposed algorithm showed accurate classification of initiating events. Also, it well predicted timings for important occurrences during severe accident progression scenarios, which is very helpful for operators to perform severe accident management

Severe accident development modeling and evaluation for CANDU

Energy Technology Data Exchange (ETDEWEB)

Negut, Gheorghe [National Agency for Radioactive Waste, 1, Campului Str., 115400 Mioveni (Romania)], E-mail: gheorghe.negut@andrad.ro; Catana, Alexandru [Institute for Nuclear Research Pitesti, 1, Campului Str., Mioveni P.O. Box 78, 0300 Pitesti (Romania); Prisecaru, Ilie; Dupleac, Daniel [Politehnica University Bucharest, 313, Splaiul Independentei, Sect. 6, 060042 Bucharest (Romania)

2009-09-15

Romania as UE member got new challenges for its nuclear industry. Romania operates since 1996 a CANDU nuclear power reactor and since 2007 the second CANDU unit. In EU are operated mainly PWR reactors, so, ours have to meet UE standards. Safety analysis guidelines require to model nuclear reactors severe accidents. Starting from previous studies, a CANDU degraded core thermal hydraulic model was developed. The initiating event is a LOCA, with simultaneous loss of moderator cooling and the loss of emergency core cooling system (ECCS). This type of accident is likely to modify the reactor geometry and will lead to a severe accident development. When the coolant temperature inside a pressure tube reaches 1000 deg. C, a contact between pressure tube and calandria tube occurs and the decay heat is transferred to the moderator. Due to the lack of cooling, the moderator, eventually, begins to boil and is expelled, through the calandria vessel relief ducts, into the containment. Therefore the calandria tubes (fuel channels) uncover, then disintegrate and fall down to the calandria vessel bottom. All the quantity of calandria moderator is vaporized and expelled, the debris will heat up and eventually boil. The heat accumulated in the molten debris will be transferred through the calandria vessel wall to the shield tank water, which surrounds the calandria vessel. The thermal hydraulics phenomena described above are modeled, analyzed and compared with the existing data.

Severe accident development modeling and evaluation for CANDU

International Nuclear Information System (INIS)

Negut, Gheorghe; Catana, Alexandru; Prisecaru, Ilie; Dupleac, Daniel

2009-01-01

Romania as UE member got new challenges for its nuclear industry. Romania operates since 1996 a CANDU nuclear power reactor and since 2007 the second CANDU unit. In EU are operated mainly PWR reactors, so, ours have to meet UE standards. Safety analysis guidelines require to model nuclear reactors severe accidents. Starting from previous studies, a CANDU degraded core thermal hydraulic model was developed. The initiating event is a LOCA, with simultaneous loss of moderator cooling and the loss of emergency core cooling system (ECCS). This type of accident is likely to modify the reactor geometry and will lead to a severe accident development. When the coolant temperature inside a pressure tube reaches 1000 deg. C, a contact between pressure tube and calandria tube occurs and the decay heat is transferred to the moderator. Due to the lack of cooling, the moderator, eventually, begins to boil and is expelled, through the calandria vessel relief ducts, into the containment. Therefore the calandria tubes (fuel channels) uncover, then disintegrate and fall down to the calandria vessel bottom. All the quantity of calandria moderator is vaporized and expelled, the debris will heat up and eventually boil. The heat accumulated in the molten debris will be transferred through the calandria vessel wall to the shield tank water, which surrounds the calandria vessel. The thermal hydraulics phenomena described above are modeled, analyzed and compared with the existing data.

Full-length fuel rod behavior under severe accident conditions

International Nuclear Information System (INIS)

Lombardo, N.J.; Lanning, D.D.; Panisko, F.E.

1992-12-01

This document presents an assessment of the severe accident phenomena observed from four Full-Length High-Temperature (FLHT) tests that were performed by the Pacific Northwest Laboratory (PNL) in the National Research Universal (NRU) reactor at Chalk River, Ontario, Canada. These tests were conducted for the US Nuclear Regulatory Commission (NRC) as part of the Severe Accident Research Program. The objectives of the test were to simulate conditions and provide information on the behavior of full-length fuel rods during hypothetical, small-break, loss-of-coolant severe accidents, in commercial light water reactors

Severe accidents in Nuclear Power Plants

International Nuclear Information System (INIS)

Valle Cepero, R.; Castillo Alvarez, J.; Ramon Fuente, J.

1996-01-01

For the assessment of the safety of nuclear power plants it is of great importance the analyses of severe accidents since they allow to estimate the possible failure models of the containment, and also permit knowing the magnitude and composition of the radioactive material that would be released to the environment in case of an accident upon population and the environment. This paper presents in general terms the basic principles for conducting the analysis of severe accidents, the fundamental sources in the generation of radionuclides and aerosols, the transportation and deposition processes, and also makes reference to de main codes used in the modulation of severe accidents. The final part of the paper contents information on how severe accidents are dialed with the regulatory point view in different countries

Bus accident severity and passenger injury: evidence from Denmark

DEFF Research Database (Denmark)

Prato, Carlo Giacomo; Kaplan, Sigal

2014-01-01

Purpose Bus safety is a concern not only in developing countries, but also in the U.S. and Europe. In Denmark, disentangling risk factors that are positively or negatively related to bus accident severity and injury occurrence to bus passengers can contribute to promote safety as an essential...... principle of sustainable transit and advance the vision “every accident is one too many”. Methods Bus accident data were retrieved from the national accident database for the period 2002–2011. A generalized ordered logit model allows analyzing bus accident severity and a logistic regression enables...... examining occurrence of injury to bus passengers. Results Bus accident severity is positively related to (i) the involvement of vulnerable road users, (ii) high speed limits, (iii) night hours, (iv) elderly drivers of the third party involved, and (v) bus drivers and other drivers crossing in yellow or red...

MCCI study for Pressurized Heavy Water Reactor under hypothetical accident condition

International Nuclear Information System (INIS)

Verma, Vishnu; Mukhopadhyay, Deb; Chatterjee, B.; Singh, R.K.; Vaze, K.K.

2011-01-01

In case of severe core damage accident in Pressurized Heavy Water Reactor (PHWR), large amount of molten corium is expected to come out into the calandria vault due to failure of calandria vessel. Molten corium at high temperature is sufficient to decompose and ablate concrete. Such attack could fail CV by basement penetration. Since containment is ultimate barrier for activity release. The Molten Core Concrete Interaction (MCCI) of the resulting pool of debris with the concrete has been identified as an important part of the accident sequence. MCCI Analysis has been carried out for PHWR for a hypothetical accident condition where total core material is considered to be relocated in calandria vault. Concrete ablation rate in vertical and radial direction is evaluated for rectangular geometry using MEDICIS module of ASTEC Code. Amount of gases released during MCCI is also evaluated. (author)

Assessment of uncertainties in severe accident management strategies

International Nuclear Information System (INIS)

Kastenberg, W.E.; Apostolakis, G.; Catton, I.; Dhir, V.K.; Okrent, D.

1990-01-01

Recent progress on the development of Probabilistic Risk Assessment (PRA) as a tool for qualifying nuclear reactor safety and on research devoted to severe accident phenomena has made severe accident management an achievable goal. Severe accident management strategies may involve operational changes, modification and/or addition of hardware, and institutional changes. In order to achieve the goal of managing severe accidents, a method for assessment of strategies must be developed which integrates PRA methodology and our current knowledge concerning severe accident phenomena, including uncertainty. The research project presented in this paper is aimed at delineating uncertainties in severe accident progression and their impact on severe accident management strategies

Pending issues for severe accident management in Wolsong plants

International Nuclear Information System (INIS)

Song, Y.M.; Kim, D.H.; Park, S.Y.

2015-01-01

While the fraction of electric power supplied from a PHWR is more than 10% in Korea, the establishment of PHWR safety enhancement based on the SAM (Severe Accident Management) technology is still weak. The final approval on the extended operation and a stress test of Wolsong-1 were made under the condition that SAM is to be enhanced. Under this situation, the current research at KAERI of Korea has a vision to strengthen the unique value of a PHWR by resolving the pending SAM issues devaluating the PHWRs’ original value. Research activities in this area will be presented. This presentation will include: The operating strategy of CFVS (Containment Filtered Vent System) for Wolsong in which vent size and closure pressure are treated because some peak spikes (at failure times of calandria and calandria vault) are difficult to be controlled; Reactor Building failure pressure at which failure probability is treated for different modes such as global and leak failures; the adequacy of DCRV (Degasser Condenser tank Relief Valve) steam relief capacity with severe SGTR source term, and Hydrogen generation and control issue which is specific to CANDU. Furthermore, current SAM guidance has a lack of information on accident diagnostic and prognostic analyses, which is difficult for the TSC (Technical Service Center) emergency staff members to deal with under real accident conditions. Thus, prototypic technologies (such as an accident inferring engine and simulator) together with SAM updates are being developed as key elements to SAM supporting tools called SAMEX-CANDU

A study on hydrogen deflagration for selected severe accident sequences in Ringhals 3

Energy Technology Data Exchange (ETDEWEB)

Gustavsson, V.; Moeller, E. [SwedPower AB (Sweden)

2002-01-01

In this report, we have investigated the most important severe accident sequences in Ringhals 3, a Westinghouse 3-loop PWR, concerning hydrogen generation and containment pressure at hydrogen deflagration. In order to analyze the accident sequences and to calculate the hydrogen production, the computer code MAAP (Modular Accident Analysis Program) was used. Six accident sequences were studied, where four were LOCA cases and two transients. MAAP gives the evolution of the accident and particularly the pressure in the containment and the production of hydrogen as a function of time. The pressure peaks at deflagration were calculated by the method AICC-Adiabatic Isochoric Complete Combustion. The results from these calculations are conservative for two reasons. Adiabatic combustion means that the heat losses to structures in the containment are neglected. The combustion is also assumed to occur once and all available hydrogen is burned. The maximum pressure in five analysed cases was compared with the failure pressure of the containment. In the LOCA case, 373 kg hydrogen was burned and the resulting peak pressure in the containment was 0,53 MPa. In the transient, where 720 kg hydrogen was burned, the peak pressure was 0,69 MPa. This is the same as the failure pressure of the containment. Finally, in the conservative case, 980 kg hydrogen was burned and the resulting peak pressure 0,96 MPa. However, it should be noted that these conclusions are conservative from two points of view. Firstly a more realistic (than AICC) calculation of the peak pressure would give a lower value than 0,69 MPa. Secondly, there is conservatism in the evaluation of the failure pressure. (au)

PWR pressure vessel integrity during overcooling accidents

International Nuclear Information System (INIS)

Cheverton, R.D.

1981-01-01

Pressurized water reactors are susceptible to certain types of hypothetical accidents that under some circumstances, including operation of the reactor beyond a critical time in its life, could result in failure of the pressure vessel as a result of propagation of crack-like defects in the vessel wall. The accidents of concern are those that result in thermal shock to the vessel while the vessel is subjected to internal pressure. Such accidents, referred to as pressurized thermal shock or overcooling accidents (OCA), include a steamline break, small-break LOCA, turbine trip followed by stuck-open bypass valves, the 1978 Rancho Seco and the TMI accidents and many other postulated and actual accidents. The source of cold water for the thermal shock is either emergency core coolant or the normal primary-system coolant. ORNL performed fracture-mechanics calculations for a steamline break in 1978 and for a turbine-trip case in 1980 and concluded on the basis of the results that many more such calculations would be required. To meet the expected demand in a realistic way a computer code, OCA-I, was developed that accepts primary-system temperature and pressure transients as input and then performs one-dimensional thermal and stress analyses for the wall and a corresponding fracture-mechanics analysis for a long axial flaw. The code is briefly described, and its use in both generic and specific plant analyses is discussed

Chemical phenomena under severe accident conditions

International Nuclear Information System (INIS)

Powers, D.A.

1988-01-01

A severe nuclear reactor accident is expected to involve a vast number of chemical processes. The chemical processes of major safety significance begin with the production of hydrogen during steam oxidation of fuel cladding. Physico-chemical changes in the fuel and the vaporization of radionuclides during reactor accidents have captured much of the attention of the safety community in recent years. Protracted chemical interactions of core debris with structural concrete mark the conclusion of dynamic events in a severe accident. An overview of the current understanding of chemical processes in severe reactor accident is provided in this paper. It is shown that most of this understanding has come from application of findings from other fields though a few areas have in the past been subject to in-depth study of a fundamental nature. Challenges in the study of severe accident chemistry are delineated

Severe accident approach - final report. Evaluation of design measures for severe accident prevention and consequence mitigation

International Nuclear Information System (INIS)

Tentner, A.M.; Parma, E.; Wei, T.; Wigeland, R.

2010-01-01

An important goal of the US DOE reactor development program is to conceptualize advanced safety design features for a demonstration Sodium Fast Reactor (SFR). The treatment of severe accidents is one of the key safety issues in the design approach for advanced SFR systems. It is necessary to develop an in-depth understanding of the risk of severe accidents for the SFR so that appropriate risk management measures can be implemented early in the design process. This report presents the results of a review of the SFR features and phenomena that directly influence the sequence of events during a postulated severe accident. The report identifies the safety features used or proposed for various SFR designs in the US and worldwide for the prevention and/or mitigation of Core Disruptive Accidents (CDA). The report provides an overview of the current SFR safety approaches and the role of severe accidents. Mutual understanding of these design features and safety approaches is necessary for future collaborations between the US and its international partners as part of the GEN IV program. The report also reviews the basis for an integrated safety approach to severe accidents for the SFR that reflects the safety design knowledge gained in the US during the Advanced Liquid Metal Reactor (ALMR) and Integral Fast Reactor (IFR) programs. This approach relies on inherent reactor and plant safety performance characteristics to provide additional safety margins. The goal of this approach is to prevent development of severe accident conditions, even in the event of initiators with safety system failures previously recognized to lead directly to reactor damage.

Severe accident approach - final report. Evaluation of design measures for severe accident prevention and consequence mitigation.

Energy Technology Data Exchange (ETDEWEB)

Tentner, A. M.; Parma, E.; Wei, T.; Wigeland, R.; Nuclear Engineering Division; SNL; INL

2010-03-01

An important goal of the US DOE reactor development program is to conceptualize advanced safety design features for a demonstration Sodium Fast Reactor (SFR). The treatment of severe accidents is one of the key safety issues in the design approach for advanced SFR systems. It is necessary to develop an in-depth understanding of the risk of severe accidents for the SFR so that appropriate risk management measures can be implemented early in the design process. This report presents the results of a review of the SFR features and phenomena that directly influence the sequence of events during a postulated severe accident. The report identifies the safety features used or proposed for various SFR designs in the US and worldwide for the prevention and/or mitigation of Core Disruptive Accidents (CDA). The report provides an overview of the current SFR safety approaches and the role of severe accidents. Mutual understanding of these design features and safety approaches is necessary for future collaborations between the US and its international partners as part of the GEN IV program. The report also reviews the basis for an integrated safety approach to severe accidents for the SFR that reflects the safety design knowledge gained in the US during the Advanced Liquid Metal Reactor (ALMR) and Integral Fast Reactor (IFR) programs. This approach relies on inherent reactor and plant safety performance characteristics to provide additional safety margins. The goal of this approach is to prevent development of severe accident conditions, even in the event of initiators with safety system failures previously recognized to lead directly to reactor damage.

Deterministic analyses of severe accident issues

International Nuclear Information System (INIS)

Dua, S.S.; Moody, F.J.; Muralidharan, R.; Claassen, L.B.

2004-01-01

Severe accidents in light water reactors involve complex physical phenomena. In the past there has been a heavy reliance on simple assumptions regarding physical phenomena alongside of probability methods to evaluate risks associated with severe accidents. Recently GE has developed realistic methodologies that permit deterministic evaluations of severe accident progression and of some of the associated phenomena in the case of Boiling Water Reactors (BWRs). These deterministic analyses indicate that with appropriate system modifications, and operator actions, core damage can be prevented in most cases. Furthermore, in cases where core-melt is postulated, containment failure can either be prevented or significantly delayed to allow sufficient time for recovery actions to mitigate severe accidents

Applicability of simplified human reliability analysis methods for severe accidents

Energy Technology Data Exchange (ETDEWEB)

Boring, R.; St Germain, S. [Idaho National Lab., Idaho Falls, Idaho (United States); Banaseanu, G.; Chatri, H.; Akl, Y. [Canadian Nuclear Safety Commission, Ottawa, Ontario (Canada)

2016-03-15

Most contemporary human reliability analysis (HRA) methods were created to analyse design-basis accidents at nuclear power plants. As part of a comprehensive expansion of risk assessments at many plants internationally, HRAs will begin considering severe accident scenarios. Severe accidents, while extremely rare, constitute high consequence events that significantly challenge successful operations and recovery. Challenges during severe accidents include degraded and hazardous operating conditions at the plant, the shift in control from the main control room to the technical support center, the unavailability of plant instrumentation, and the need to use different types of operating procedures. Such shifts in operations may also test key assumptions in existing HRA methods. This paper discusses key differences between design basis and severe accidents, reviews efforts to date to create customized HRA methods suitable for severe accidents, and recommends practices for adapting existing HRA methods that are already being used for HRAs at the plants. (author)

Development of Krsko Severe Accident Management Database (SAMD)

International Nuclear Information System (INIS)

Basic, I.; Kocnar, R.

1996-01-01

Severe Accident Management is a framework to identify and implement the Emergency Response Capabilities that can be used to prevent or mitigate severe accidents and their consequences. Krsko Severe Accident Management Database documents the severe accident management activities which are developed in the NPP Krsko, based on the Krsko IPE (Individual Plant Examination) insights and Generic WOG SAMGs (Westinghouse Owners Group Severe Accident Management Guidance). (author)

United States position on severe accidents

International Nuclear Information System (INIS)

Ross, D.F.

1988-01-01

The United States policy on severe accidents was published in 1985 for both new plant applications and for existing plants. Implementation of this policy is in progress. This policy, aided by a related safety goal policy and by analysis capabilities emerging from improved understanding of accident phenomenology, is viewed as a logical development from the pioneering work in the WASH-1400 Reactor Safety Study published by the United States Nuclear Regulatory Commission (NRC) in 1975. This work provided an estimate of the probability and consequences of severe accidents which, prior to that time, had been mostly evaluated by somewhat arbitrary assumptions dating back 30 years. The early history of severe accident evaluation is briefly summarized for the period 1957-1979. Then, the galvanizing action of Three Mile Island Unit 2 (TMI-2) on severe accident analysis, experimentation and regulation is reviewed. Expressions of US policy in the form of rulemaking, severe accident policy, safety research, safety goal policy and court decisions (on adequacy of safety) are discussed. Finally, the NRC policy as of March 1988 is stated, along with a prospective look at the next few years. (author). 19 refs

National practices in relation to severe accidents

International Nuclear Information System (INIS)

Soda, Kunihisa

1989-01-01

After the accidents at Three Mile Island and Chernobyl, many studies have been carried out on severe accidents by various organizations including IAEA and OECD/CSNI. In the present article, measures taken in different countries against severe accidents are outlined based on the results of these studies. In Sweden, policies for the management of a severe accident and reduction in the release of radioactive materials were established based on reports issued by the Atomic Energy Committee, which was set up after the Three Mile Island accident. The current policies require that filter vents be provided where necessary. France, following Sweden, adopted the use of filter vents. Operation procedures to be followed in the event of a severe accident have been established in the nation. The measures against severe accidents adopted in West Germany mainly focus on the weakening of the effects of accidents, and are not covered by the design standards. The use of filter vents are also required in Finland and Switzerland. In the U.S., a program for individual plant examination will be implemented over the three-year period beginning in 1989. Studies on measures against severe accidents seem to be performed also in the Soviet Union. (N.K.)

Severe Accident Test Station Design Document

Energy Technology Data Exchange (ETDEWEB)

Snead, Mary A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Yan, Yong [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Howell, Michael [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Keiser, James R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Terrani, Kurt A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-09-01

The purpose of the ORNL severe accident test station (SATS) is to provide a platform for evaluation of advanced fuels under projected beyond design basis accident (BDBA) conditions. The SATS delivers the capability to map the behavior of advanced fuels concepts under accident scenarios across various temperature and pressure profiles, steam and steam-hydrogen gas mixtures, and thermal shock. The overall facility will include parallel capabilities for examination of fuels and irradiated materials (in-cell) and non-irradiated materials (out-of-cell) at BDBA conditions as well as design basis accident (DBA) or loss of coolant accident (LOCA) conditions. Also, a supporting analytical infrastructure to provide the data-needs for the fuel-modeling components of the Fuel Cycle Research and Development (FCRD) program will be put in place in a parallel manner. This design report contains the information for the first, second and third phases of design and construction of the SATS. The first phase consisted of the design and construction of an out-of-cell BDBA module intended for examination of non-irradiated materials. The second phase of this work was to construct the BDBA in-cell module to test irradiated fuels and materials as well as the module for DBA (i.e. LOCA) testing out-of-cell, The third phase was to build the in-cell DBA module. The details of the design constraints and requirements for the in-cell facility have been closely captured during the deployment of the out-of-cell SATS modules to ensure effective future implementation of the in-cell modules.

Severe Accident Test Station Design Document

International Nuclear Information System (INIS)

Snead, Mary A.; Yan, Yong; Howell, Michael; Keiser, James R.; Terrani, Kurt A.

2015-01-01

The purpose of the ORNL severe accident test station (SATS) is to provide a platform for evaluation of advanced fuels under projected beyond design basis accident (BDBA) conditions. The SATS delivers the capability to map the behavior of advanced fuels concepts under accident scenarios across various temperature and pressure profiles, steam and steam-hydrogen gas mixtures, and thermal shock. The overall facility will include parallel capabilities for examination of fuels and irradiated materials (in-cell) and non-irradiated materials (out-of-cell) at BDBA conditions as well as design basis accident (DBA) or loss of coolant accident (LOCA) conditions. Also, a supporting analytical infrastructure to provide the data-needs for the fuel-modeling components of the Fuel Cycle Research and Development (FCRD) program will be put in place in a parallel manner. This design report contains the information for the first, second and third phases of design and construction of the SATS. The first phase consisted of the design and construction of an out-of-cell BDBA module intended for examination of non-irradiated materials. The second phase of this work was to construct the BDBA in-cell module to test irradiated fuels and materials as well as the module for DBA (i.e. LOCA) testing out-of-cell, The third phase was to build the in-cell DBA module. The details of the design constraints and requirements for the in-cell facility have been closely captured during the deployment of the out-of-cell SATS modules to ensure effective future implementation of the in-cell modules.

Structural evaluation of electrosleeved tubes under severe accident transients

International Nuclear Information System (INIS)

Majumdar, S.

1999-01-01

A flow stress model was developed for predicting failure of Electrosleeved PWR steam generator tubing under severe accident transients. The Electrosleeve, which is nanocrystalline pure nickel, loses its strength at temperatures greater than 400 C during severe accidents because of grain growth. A grain growth model and the Hall-Petch relationship were used to calculate the loss of flow stress as a function of time and temperature during the accident. Available tensile test data as well as high temperature failure tests on notched Electrosleeved tube specimens were used to derive the basic parameters of the failure model. The model was used to predict the failure temperatures of Electrosleeved tubes with axial cracks in the parent tube during postulated severe accident transients

Recent Perspective on the Severe Accident Management Programme for Nuclear Power Plant

International Nuclear Information System (INIS)

Kim, Manwoong; Lee, Sukho; Lee, Jungjae; Chung, Kuyoung

2017-01-01

Severe Accident Management Guidelines (SAMGs), has been developed to help operators to prevent or mitigate the impacts of accidents at nuclear power plants. Severe accident management was first introduced in the 1990s with the creation of SAMGs following recognition that post-Three Mile Island Emergency Operating Procedures (EOPs) did not adequately address severe core damage conditions. Establishing and maintaining multiple layers of defence against any internal/external hazards is an important measure to reduce radiological risks to the public and environment. This study is intended to suggest future regulatory perspectives to strengthen the prevention and mitigation strategies for severe accidents by review of the current status of revision of IAEA Safety Standard on Severe Accident Management Programmes for Nuclear Power Plants and the combined PWR SAMG. This new IAEA Safety Guide will address guidelines for preparation, development, implementation and review of severe accident management programs during all operating conditions for both reactor and spent fuel pool. This Guide is used by operating organizations of nuclear power plants and their support organizations. It may also be used by national regulatory bodies and technical support organizations as a reference for developing their relevant safety requirements and for conducting reviews and safety assessments for SAMP including SAMG. The Pressurized Water Reactor Owner’s Group (PWROG) is upgrading the original generic Severe Accident Management Guidelines (SAMGs) into single Severe Accident Guidelines (SAGs) for the PWR SAMG aims to consolidate the advantages of each of the separate vendor severe accident (SA) mitigation methods. This new PWROG SAGs changes the SAMG process to be made that can improve SA response. Changes have been made that guidance is available for control room operators when the TSC is not activated thus allowing for timely accident response. Other changes were made to the guidance

Experiments to evaluate behavior of containment piping bellows under severe accident conditions

International Nuclear Information System (INIS)

Lambert, L.D.; Parks, M.B.

1993-01-01

Bellows are an integral part of the containment pressure boundary in nuclear power plants. They are used at piping penetrations to allow relative movement between piping and the containment wall. In a severe accident they may be subjected to high pressure and temperature, and a combination of axial and lateral deflections. A test program to determine the leak-tight capacity of containment penetration bellows is being conducted at Sandia National Laboratories, Albuquerque, New Mexico. Several different bellows geometries, representative of actual containment bellows, are being subjected to extreme deflections along with pressure and temperature loads. The bellows geometries and loading conditions are described along with the testing apparatus and procedures. A total of thirteen tests have been conducted. The tests showed that withstanding relatively large bellows are capable of deformations, up to, or near, the point of full compression before developing leakage. The test data is presented and discussed

Radionuclide release calculations for selected severe accident scenarios

International Nuclear Information System (INIS)

Denning, R.S.; Leonard, M.T.; Cybulskis, P.; Lee, K.W.; Kelly, R.F.; Jordan, H.; Schumacher, P.M.; Curtis, L.A.

1990-08-01

This report provides the results of source term calculations that were performed in support of the NUREG-1150 study. ''Severe Accident Risks: An Assessment for Five US Nuclear Power Plants.'' This is the sixth volume of a series of reports. It supplements results presented in the earlier volumes. Analyses were performed for three of the NUREG-1150 plants: Peach Bottom, a Mark I, boiling water reactor; Surry, a subatmospheric containment, pressurized water reactor; and Sequoyah, an ice condenser containment, pressurized water reactor. Complete source term results are presented for the following sequences: short term station blackout with failure of the ADS system in the Peach Bottom plant; station blackout with a pump seal LOCA for the Surry plant; station blackout with a pump seal LOCA in the Sequoyah plant; and a very small break with loss of ECC and spray recirculation in the Sequoyah plant. In addition, some partial analyses were performed which did not require running all of the modules of the Source Term Code Package. A series of MARCH3 analyses were performed for the Surry and Sequoyah plants to evaluate the effects of alternative emergency operating procedures involving primary and secondary depressurization on the progress of the accident. Only thermal-hydraulic results are provided for these analyses. In addition, three accident sequences were analyzed for the Surry plant for accident-induced failure of steam generator tubes. In these analyses, only the transport of radionuclides within the primary system and failed steam generator were examined. The release of radionuclides to the environment is presented for the phase of the accident preceding vessel meltthrough. 17 refs., 176 figs., 113 tabs

Core loss during a severe accident (COLOSS)

International Nuclear Information System (INIS)

Adroguer, B.; Bertrand, F.; Chatelard, P.; Cocuaud, N.; Van Dorsselaere, J.P.; Bellenfant, L.; Knocke, D.; Bottomley, D.; Vrtilkova, V.; Belovsky, L.; Mueller, K.; Hering, W.; Homann, C.; Krauss, W.; Miassoedov, A.; Schanz, G.; Steinbrueck, M.; Stuckert, J.; Hozer, Z.; Bandini, G.; Birchley, J.; Berlepsch, T. von; Kleinhietpass, I.; Buck, M.; Benitez, J.A.F.; Virtanen, E.; Marguet, S.; Azarian, G.; Caillaux, A.; Plank, H.; Boldyrev, A.; Veshchunov, M.; Kobzar, V.; Zvonarev, Y.; Goryachev, A.

2005-01-01

The COLOSS project was a 3-year shared-cost action, which started in February 2000. The work-programme performed by 19 partners was shaped around complementary activities aimed at improving severe accident codes. Unresolved risk-relevant issues regarding H 2 production, melt generation and the source term were studied through a large number of experiments such as (a) dissolution of fresh and high burn-up UO 2 and MOX by molten Zircaloy (b) simultaneous dissolution of UO 2 and ZrO 2 (c) oxidation of U-O-Zr mixtures (d) degradation-oxidation of B 4 C control rods. Corresponding models were developed and implemented in severe accident computer codes. Upgraded codes were then used to apply results in plant calculations and evaluate their consequences on key severe accident sequences in different plants involving B 4 C control rods and in the TMI-2 accident. Significant results have been produced from separate-effects, semi-global and large-scale tests on COLOSS topics enabling the development and validation of models and the improvement of some severe accident codes. Breakthroughs were achieved on some issues for which more data are needed for consolidation of the modelling in particular on burn-up effects on UO 2 and MOX dissolution and oxidation of U-O-Zr and B 4 C-metal mixtures. There was experimental evidence that the oxidation of these mixtures can contribute significantly to the large H 2 production observed during the reflooding of degraded cores under severe accident conditions. The plant calculation activity enabled (a) the assessment of codes to calculate core degradation with the identification of main uncertainties and needs for short-term developments and (b) the identification of safety implications of new results. Main results and recommendations for future R and D activities are summarized in this paper

A Bayesian ensemble of sensitivity measures for severe accident modeling

Energy Technology Data Exchange (ETDEWEB)

Hoseyni, Seyed Mohsen [Department of Basic Sciences, East Tehran Branch, Islamic Azad University, Tehran (Iran, Islamic Republic of); Di Maio, Francesco, E-mail: francesco.dimaio@polimi.it [Energy Department, Politecnico di Milano, Via La Masa 34, 20156 Milano (Italy); Vagnoli, Matteo [Energy Department, Politecnico di Milano, Via La Masa 34, 20156 Milano (Italy); Zio, Enrico [Energy Department, Politecnico di Milano, Via La Masa 34, 20156 Milano (Italy); Chair on System Science and Energetic Challenge, Fondation EDF – Electricite de France Ecole Centrale, Paris, and Supelec, Paris (France); Pourgol-Mohammad, Mohammad [Department of Mechanical Engineering, Sahand University of Technology, Tabriz (Iran, Islamic Republic of)

2015-12-15

Highlights: • We propose a sensitivity analysis (SA) method based on a Bayesian updating scheme. • The Bayesian updating schemes adjourns an ensemble of sensitivity measures. • Bootstrap replicates of a severe accident code output are fed to the Bayesian scheme. • The MELCOR code simulates the fission products release of LOFT LP-FP-2 experiment. • Results are compared with those of traditional SA methods. - Abstract: In this work, a sensitivity analysis framework is presented to identify the relevant input variables of a severe accident code, based on an incremental Bayesian ensemble updating method. The proposed methodology entails: (i) the propagation of the uncertainty in the input variables through the severe accident code; (ii) the collection of bootstrap replicates of the input and output of limited number of simulations for building a set of finite mixture models (FMMs) for approximating the probability density function (pdf) of the severe accident code output of the replicates; (iii) for each FMM, the calculation of an ensemble of sensitivity measures (i.e., input saliency, Hellinger distance and Kullback–Leibler divergence) and the updating when a new piece of evidence arrives, by a Bayesian scheme, based on the Bradley–Terry model for ranking the most relevant input model variables. An application is given with respect to a limited number of simulations of a MELCOR severe accident model describing the fission products release in the LP-FP-2 experiment of the loss of fluid test (LOFT) facility, which is a scaled-down facility of a pressurized water reactor (PWR).

Perspectives on phenomenology and simulation of severe accident in light water reactors

International Nuclear Information System (INIS)

Sugimoto, Jun

2014-01-01

Severe accident phenomena in light water reactors (LWRs) are generally characterized by their physically and chemically complex processes involved with high temperature core melt, multi-component and multi-phase flows, transport of radioactive materials and sometimes highly non-equilibrium state. Severe accident phenomenology is usually categorized into four phases; (1) fuel degradation, (2) in-vessel phenomena, (3) ex-vessel phenomena and (4) fission product release and transport. Among these, ex-vessel phenomena consist of five subcategories; 1) direct containment heating, 2) fuel coolant interaction (steam explosion), 3) molten core concrete interaction, 4) hydrogen behaviour and control and 5) containment failure/leakage. In the field of simulation of severe accident, severe accident analytical codes have been developed in the United States, EU and Japan, such as MAAP, MELCOR, ASTEC, THALES and SAMPSON. Many different kinds of analytical codes for the specific severe accident phenomena have also been developed worldwide. After the accident at Fukushima Daiichi Nuclear Power Station, review of severe accident research issues has been conducted and several issues are reconsidered, such as effects of BWR core degradation behaviors, sea water injection, pool scrubbing under rapid depressurization, containment failure/leakage and re-criticality. Some new experimental and analytical efforts have been started after the Fukushima accident. The present paper describes the perspectives on phenomenology and simulation of severe accident in LWRs, with the emphasis of insights obtained in the review of Fukushima accident. (author)

Use of PSA and severe accident assessment results for the accident management

International Nuclear Information System (INIS)

Jang, S. H.; Kim, H. G.; Jang, H. S.; Moon, S. K.; Park, J. U.

1993-12-01

The objectives for this study are to investigate the basic principle or methodology which is applicable to accident management, by using the results of PSA and severe accident research, and also facilitate the preparation of accidents management program in the future. This study was performed as follows: derivation of measures for core damage prevention, derivation of measures for accident mitigation, application of computerized tool to assess severe accident management

Use of PSA and severe accident assessment results for the accident management

Energy Technology Data Exchange (ETDEWEB)

Jang, S H; Kim, H G; Jang, H S; Moon, S K; Park, J U [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

1993-12-15

The objectives for this study are to investigate the basic principle or methodology which is applicable to accident management, by using the results of PSA and severe accident research, and also facilitate the preparation of accidents management program in the future. This study was performed as follows: derivation of measures for core damage prevention, derivation of measures for accident mitigation, application of computerized tool to assess severe accident management.

Development of Severe Accident Management Strategies for Shin-Kori 3 and 4

International Nuclear Information System (INIS)

Lee, Youngseung; Kim, Hyeongtaek; Shin, Jungmin

2013-01-01

Shin-Kori units 3 and 4 are new reactors under construction as an APR 1400 type reactor. The plants which considered coping with severe accident from design phase are different from other operating plants in view of severe accident management strategies. The purpose of this paper is to establish optimal strategies for Shin-Kori 3 and 4. A scheme for optimized severe accident management was drawn up with the object of achieving core cooling, containment integrity, and decreased release of fission product. Shin-Kori units 3 and 4 are a new reactor and designed to add mitigating systems for coping with severe accident such as ECSBS, PAR, and CFS. Also the plants are reflected as a part of Fukushima followup measures The strategies of SAMG for Shin-Kori 3 and 4 were developed. The strategic approach was based on the concept of defense in depth. Firstly, strategies for core cooling were chosen such as RCS depressurization, injection to SG, injection to RCS, and injection to reactor cavity. Secondly, the plans for containment integrity were developed for controlling pressure and hydrogen in containment. Lastly, reduced release of fission product was considered for protection of the public after containment failure. The achieved strategies meet the needs of effective methods for severe accident management and enhancement of safety

Radionuclide release calculations for selected severe accident scenarios. PWR, ice condenser design

Energy Technology Data Exchange (ETDEWEB)

Denning, R S; Gieseke, J A; Cybulskis, P; Lee, K W; Jordan, H; Curtis, L A; Kelly, R F; Kogan, V; Schumacher, P M

1986-07-01

This report presents results of analyses of the environmental releases of fission products (source terms) for severe accident scenarios in a pressurized water reactor with an ice-condenser containment. The analyses were performed to support the Severe Accident Risk Reduction/Risk Rebaselining Program (SARRP) which is being undertaken for the U.S. Nuclear Regulatory Commission by Sandia National Laboratories. In the SARRP program, risk estimates are being generated for a number of reference plant designs. The Sequoyah Plant has been used in this study as an example of a PWR ice-condenser plant. (author)

Mitigation of severe accidents in AREVA's Gen 3+ nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Fischer, M., E-mail: manfred.fischer@areva.com; Henning, A.; Surmann, R.

2014-04-01

The current AREVA Gen 3+ PWR designs (EPR™ and ATMEA1) are based on the proven defense-in-depth safety concepts inherited from their predecessors, the French “N4” and the German “Konvoi” reactors. Complemented by specific enhancements, including higher redundancy and diversity as well as the use of passive systems, this leads to very low values of the core damage frequency (CDF). Notwithstanding this very low probability, dedicated design measures have been implemented to improve the response of the plant in case of a postulated severe accident (SA) with core melting. This way not only the frequency of large-early-releases (LERF) but also the related radiological consequences are drastically reduced. Situations that potentially lead to high loads that can challenge the short-term integrity of the containment, like RPV melt-through under high pressure, energetic hydrogen/steam explosions, as well as long-term containment failure caused by internal over-pressure are avoided by a combination of preventive measures and dedicated systems. At the example of the EPR{sup TM}, the paper gives an overview of the severe accident mitigation strategy and the related measures and systems of AREVAs current Gen 3+ reactors, with special focus on the function of the core melt stabilization system.

Improvement of severe accident analysis method for KSNP

Energy Technology Data Exchange (ETDEWEB)

Park, Jae Hong [Korea Institute of Nuclear Safety, Taejon (Korea, Republic of); Cho, Song Won; Cho, Youn Soo [Korea Radiation Technology Institute Co., Taejon (Korea, Republic of)

2002-03-15

The objective of this study is preparation of MELCOR 1.8.5 input deck for KSNP and simulation of some major severe accidents. The contents of this project are preparation of MELCOR 1.8.5 base input deck for KSNP to understand severe accident phenomena and to assess severe accident strategy, preparation of 20 cell containment input deck to simulate the distribution of hydrogen and fission products in containment, simulation of some major severe accident scenarios such as TLOFW, SBO, SBLOCA, MBLOCA, and LBLOCA. The method for MELCOR 1.8.5 input deck preparation can be used to prepare the input deck for domestic PWRs and to simulate severe accident experiments such as ISP-46. Information gained from analyses of severe accidents may be helpful to set up the severe accident management strategy and to develop regulatory guidance.

Thermalydraulic processes in the reactor coolant system of a BWR under severe accident conditions

International Nuclear Information System (INIS)

Hodge, S.A.

1990-01-01

Boiling water reactors (BWRs) incorporate many unique structural features that make their expected response under severe accident conditions very different from that predicted in the case of pressurized water reactor accident sequences. Automatic main steam isolation valve (MIV) closure as the vessel water level approaches the top of the core would cause reactor vessel isolation while automatic recirculation pump trip would limit the in-vessel flows to those characteristic of natural circulation (as disturbed by vessel relief valve actuation). This paper provides a discussion of the BWR control blade, channel box, core plate, control rod guide tube, and reactor vessel safety relief valve (SRV) configuration and the effects of these structural components upon thermal hydraulic processes within the reactor vessel under severe accident conditions. The dominant BWR severe accident sequences as determined by probabilistic risk assessment are described and the expected timing of events for the unmitigated short-term station blackout severe accident sequence at the Peach Bottom atomic power station is presented

A generic approach for containment success criteria under severe accident loads

International Nuclear Information System (INIS)

Sammataro, R.F.; Solonick, W.R.; Edwards, N.W.

1992-01-01

The U.S. Department of Energy (DOE), Office of New Production Reactors (NP), has identified safety as the foremost design criterion for the Heavy Water New Production Reactor (NPR-HWR). The DOE-NP has issued the Deterministic Severe Accident Criteria (DSACs) to guide the design of the NPR-HWR containment for resistance to severe accidents. The DSAC concept provides for a generic approach for success criteria to predict the threshold of containment failure under severe accident loads. This concept consists of two parts: (1) Problem Statements that are qualitative and quantitative bases for calculating associated loadings and containment response to those loadings, and (2) Success Criteria that specify acceptable containment response measures and limits for each problem statement. This paper is limited to a discussion of a generic approach for containment success criteria. The main elements of these success criteria are expressed in terms of elastic stresses and inelastic strains. Containment performance is based on the best estimate of failure as predicted by either stress or strain, buckling, displacements, or ability to withstand missile perforation. Since these limits are best estimates of failure, no conservatism exists in these success criteria. Rather, conservatism is to be provided in the problem statements, i.e., the quantified severe accident loads. These success criteria are presented on a multi-tiered basis for static pressure and temperature loadings, dynamic loadings, and missiles. Within the static pressure and temperature loadings and the dynamic loadings, the criteria are separated into elastic analysis success criteria and inelastic analysis success criteria. Each of these areas, in turn, defines limits on either the stress or strain measures as well as on measures for buckling and displacements

Extreme accident mitigation - analysis of a low pressure secondary containment building

International Nuclear Information System (INIS)

Vaughan, G.J.; Dunbar, I.H.

1987-01-01

Although whole core accidents are sufficiently unlikely as to be beyond the design basis, the Secondary Containment Building [SCB] is expected to have some effect in mitigating the consequences of such accidents. From a design point of view there are many advantages in having a low pressure SCB fitted with a filtered vent, so studies have been undertaken of the response of such a building to the large sodium fires that might follow a severe accident. The behaviour of the sodium oxide aerosols has been studied using the code AEROSIM. The efficiency of an aerosol scrubber has been investigated experimentally. A simple code, SECCONTAIN, has been developed to model the effects of sodium fires in buildings, and has been applied to a specific design of a low pressure SCB. (author)

The External Cost Evaluation of the Nuclear Severe Accident Using CVM

International Nuclear Information System (INIS)

Lee, Yong Suk; Lee, Byung Chul

2006-01-01

The external cost of energy can be defined as 'the cost not included in the energy market price', such as air pollution, noise, etc. Within the evaluation of the external cost of nuclear energy, the estimation of the external cost of severe accident is one of the major topics to be addressed. For the evaluation of the external cost of severe accident, the effect of risk aversion of the public against the severe accident must be addressed, because people are more concerned about low probability - high consequence events than about high probability - low consequence events having the same mean damage. It is generally recognized that there is a discrepancy between the social acceptability of the risk and the average monetary value which corresponds in principle to the compensation of the consequences for each individual of the population affected by the accident. In this paper, the CVM (Contingent Valuation Method) is used to integrate the risk aversion in the external costs of nuclear severe accidents in Korea

Studies of severe accidents in light-water reactors

International Nuclear Information System (INIS)

1987-01-01

From 10 to 12 November 1986 some 80 delegates met under the auspices of the CEC working group on the safety of light-water reactors. The participants from EC Member States were joined by colleagues from Sweden, Finland and the USA and met to discuss the subject of severe accidents in LWRs. Although this seminar had been planned well before Chernobyl, the ''severe-accident-that-really-happened'' made its mark on the seminar. The four main seminar topics were: (i) high source-term accident sequences identified in PSAs, (ii) containment performance, (iii) mitigation of core melt consequences, (iv) severe accident management in LWRs. In addition to the final panel discussion there was also a separate panel discussion on lessons learned from the Chernobyl accident. These proceedings include the papers presented during the seminar and they are arranged following the seminar programme outline. The presentations and discussions of the two panels are not included in the proceedings. The general conclusions and directions following from these two panels were, however, considered in a seminar review paper which was published in the March 1987 issue of Nuclear Engineering International

Jose Cabrera NPP severe accident management activities

International Nuclear Information System (INIS)

Blanco, J.; Almeida, P.; Saiz, J.; Sastre, J.L.; Delgado, R.

1998-01-01

To prepare a common acting plan with respect to Severe Accident Management, in 1994 was founded the severe accident management ''ad-hoc'' working group from the Spanish Westinghouse PWR Nuclear Power Plant Owners Group. In this group actively collaborated the Jose Cabrera NPP Training Centre and the Department of Nuclear Engineering of UNION FENOSA. From this moment, Jose Cabrera NPP began the planning of its specific Severe Accident Management Program, which main point are Severe Accident Management Guidelines (SAMG). To elaborate this guidelines, the Spanish translation of Westinghouse Owners Group (WOG) Severe Accident Management Guidelines were considered the reference documents. The implementation of this Guidelines to Jose Cabrera NPP started on January 1997. Once the specific guidelines have been implemented to the plant, training activities for the personnel involved in severe accident issues will be developed. To prepare the training exercises MAAP4 code will be used, and with this intention, a specific Jose Cabrera NPP MAAP-GRAAPH screen has been developed. Furthermore, a wide selection of MAAP input files for the simulation of different scenarios and accidental events is available. (Author)

Severe accident management guidelines tool

International Nuclear Information System (INIS)

Gutierrez Varela, Javier; Tanarro Onrubia, Augustin; Martinez Fanegas, Rafael

2014-01-01

Severe Accident is addressed by means of a great number of documents such as guidelines, calculation aids and diagnostic trees. The response methodology often requires the use of several documents at the same time while Technical Support Centre members need to assess the appropriate set of equipment within the adequate mitigation strategies. In order to facilitate the response, TECNATOM has developed SAMG TOOL, initially named GGAS TOOL, which is an easy to use computer program that clearly improves and accelerates the severe accident management. The software is designed with powerful features that allow the users to focus on the decision-making process. Consequently, SAMG TOOL significantly improves the severe accident training, ensuring a better response under a real situation. The software is already installed in several Spanish Nuclear Power Plants and trainees claim that the methodology can be followed easier with it, especially because guidelines, calculation aids, equipment information and strategies availability can be accessed immediately (authors)

Study on entry criteria for severe accident management during hot leg LBLOCAs in a PWR

International Nuclear Information System (INIS)

Zhang, Longfei; Zhang, Dafa; Wang, Shaoming

2007-01-01

The risk of Large Break Loss of Coolant Accidents (LBLOCA) has been considered an important safety issue since the beginning of the nuclear power industry. The rapid depressurization occurs in the primary coolant circuit when a large break appears in a Pressurized Water Reactors (PWR).Then the coolant temperature reaches saturation at a very low pressure. The core outlet fluid temperatures maybe not reliable indicators of the core damage states at a such lower pressure. The problem is how to decide the time for water injection in the SAM (Severe Accident Management). An alternative entry criterion is the fluid temperature just above the hot channel in which the fluid temperature showed maximum among all the channels. For that reason, a systematic study of entry criterion of SAM for different hot leg break sizes in a 3-loop PWR has been started using the detailed system thermal hydraulic and severe accident analysis code package, RELAP/SCDAPSIM. Best estimate calculations of the large break LOCA of 15 cm, 20 cm and 25 cm without accident managements and in the case of high-pressure safety injection as the accident management were performed in this paper. The analysis results showed that the core exit temperatures are not reliable indicators of the peak core temperatures and core damage states once peak core temperatures reach 1500 K, and the proposed entry criteria for SAM at the time when the core outlet temperature reaches 900 K is not effective to prevent core melt. Then other analyses were performed with a parameter of fluid temperature just above the hot channel. The latter analysis showed that earlier water injection when the fluid temperature just above the hot channel reaches 900 K is effective to prevent further core melt. Since fuel surface and hot channel have spatial distribution and depend on a period of cycle operation, a series of thermocouples are required to install just above the fuel assembly. The maximum exit temperature of 900 K that captured by

Pressure drop-flow rate curves for single-phase steam in Combustion Engineering type steam generator U-tubes during severe accidents

Energy Technology Data Exchange (ETDEWEB)

Fynan, Douglas A.; Ahn, Kwang-Il, E-mail: kiahn@kaeri.re.kr

2016-12-15

Highlights: • Pressure drop-flow rate curves for superheated steam in U-tubes were generated. • Forward flow of hot steam is favored in the longer and taller U-tubes. • Reverse flow of cold steam is favored in short U-tubes. • Steam generator U-tube bundle geometry and tube diameter are important. • Need for correlation development for natural convention heat transfer coefficient. - Abstract: Characteristic pressure drop-flow rate curves are generated for all row numbers of the OPR1000 steam generators (SGs), representative of Combustion Engineering (CE) type SGs featuring square bend U-tubes. The pressure drop-flow rate curves are applicable to severe accident natural circulations of single-phase superheated steam during high pressure station blackout sequences with failed auxiliary feedwater and dry secondary side which are closely related to the thermally induced steam generator tube rupture event. The pressure drop-flow rate curves which determine the recirculation rate through the SG tubes are dependent on the tube bundle geometry and hydraulic diameter of the tubes. The larger CE type SGs have greater variation of tube length and height as a function of row number with forward flow of steam favored in the longer and taller high row number tubes and reverse flow favored in the short low row number tubes. Friction loss, natural convection heat transfer coefficients, and temperature differentials from the primary to secondary side are dominant parameters affecting the recirculation rate. The need for correlation development for natural convection heat transfer coefficients for external flow over tube bundles currently not modeled in system codes is discussed.

Research on sever accident emergency simulation system for CPR1000

International Nuclear Information System (INIS)

Yang Zhifei; Liao Yehong; Liang Manchun; Li Ke; Yang Jie; Chen Yali

2015-01-01

The enhanced capability to nuclear power plant (NPP) severe accident management and emergency response depends heavily on exercises. Since the exercise scene is usually monotonous and not realistic, and conduct of exercise has a high cost, the effect of enhancing the capability is limited. Thus, the development of a Sever Accident Emergency Simulation System (SAESS) is necessary. SAESS is able to connect NPP simulator, and simulates the process of severe accident management, personnel evacuation, the dispersion of radioactive plume, and emergency response of emergency organizations. The system helps to design several of exercise scenes and optimize the disposal strategy in different severe accidents. In addition, the system reduces the cost of emergency exercise by computer simulation, benefits the research of exercise, increases the efficiency of exercise and enhances the emergency decision-making capability. This paper introduces the design and application of SAESS. (author)

Severe accident management. Prevention and Mitigation

International Nuclear Information System (INIS)

1992-01-01

Effective planning for the management of severe accidents at nuclear power plants can produce both a reduction in the frequency of such accidents as well as the ability to mitigate their consequences if and when they should occur. This report provides an overview of accident management activities in OECD countries. It also presents the conclusions of a group of international experts regarding the development of accident management methods, the integration of accident management planning into reactor operations, and the benefits of accident management

The development of severe accident analysis technology

Energy Technology Data Exchange (ETDEWEB)

Kim, Heuy Dong; Cho, Sung Won; Kim, Sang Baek; Park, Jong Hwa; Lee, Kyu Jung; Park, Lae Joon; Hu, Hoh; Hong, Sung Wan [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1993-07-01

The objective of the development of severe accident analysis technology is to understand the severe accident phenomena such as core melt progression and to provide a reliable analytical tool to assess severe accidents in a nuclear power plant. Furthermore, establishment of the accident management strategies for the prevention/mitigation of severe accidents is also the purpose of this research. The study may be categorized into three areas. For the first area, two specific issues were reviewed to identify the further research direction, that is the natural circulation in the reactor coolant system and the fuel-coolant interaction as an in-vessel and an ex-vessel phenomenological study. For the second area, the MELCOR and the CONTAIN codes have been upgraded, and a validation calculation of the MELCOR has been performed for the PHEBUS-B9+ experiment. Finally, the experimental program has been established for the in-vessel and the ex-vessel severe accident phenomena with the in-pile test loop in KMRR and the integral containment test facilities, respectively. (Author).

Thermal-hydraulic uncertainties affecting severe accident progression

International Nuclear Information System (INIS)

Haskin, F.E.; Behr, V.L.

1984-01-01

To provide the proper technical bases for decisions regarding severe accidents, the US Nuclear Regulatory Commission (NRC) is sponsoring the following activities: (a) a variety of severe accident research programs, combined under the Severe Accident Research Plan; (b) nationwide task forces on containment loading, containment response, and fission product source terms; (c) a review by the American Physical Society of state-of-the-art methods for calculating radiological source terms; and (d) technical exchange meetings with the Industry Degraded Core (IDCOR) program. One of the means for integrating this developing array of technical information is the Severe Accident Risk Reduction Program (SARRP). One of the current SARRP objectives is to utilize insights gained from the activities listed above to characterize the relative likelihoods of competing containment failure modes for core-melt accidents

Preliminary Analysis of Severe Accident Progression Initiated from Small Break LOCA of a SMART Reactor

International Nuclear Information System (INIS)

Jin, Young Ho; Park, Jong Hwa; Kim, Dong Ha; Cho, Seong Won

2010-01-01

SMART (System integrated Modular Advanced ReacTor), is under the development at Korea Atomic Energy Research Institute (KAERI). SMART is an integral type pressurized water reactor which contains a pressurizer, 4 reactor coolant pumps (RCPs), and 8 steam generator cassettes(S/Gs) in a single reactor vessel. This reactor has substantially enhanced its safety with an integral layout of its major components, 4 trains of safety injection systems (SISs), and an adoption of 4 trains of passive residual heat removal systems (PRHRS) instead of an active auxiliary feedwater system . The thermal power is 330 MWth. During the conceptual design stage, a preliminary PSA was performed. PSA results identified that a small break loss of coolant accident (SLOCA) with all safety injections unavailable is one of important severe core damage sequences. Clear understanding of this sequence helps in the developing accident mitigation strategies. MIDAS/SMR computer code is used to simulate the severe accident progression initiated from a small break LOCA in SMART reactor. This code has capability to model a helical steam generator which is adopted in SMART reactor. The important accident progression results for SMART reactor are then compared with the typical pressurized water reactor (PWR) result

EPR design features to mitigate severe accident challenges

International Nuclear Information System (INIS)

Mazurkiewicz, S.M.; Fischer, M.; Bittermann, D.

2005-01-01

The EPR, an evolutionary pressurized water reactor (PWR), is a 4300-4500 MWth that incorporates proven technology within an optimized configuration to enhance safety. EPR was originally developed through a joint effort between Framatome ANP and Siemens by incorporating the best technological features from the French and German nuclear reactor fleets into a cost-competitive product. Commercial EPR units are currently being built in Finland at the Olkiluoto site, and planned for France at the Flamanville site. In recent months, Framatome ANP announced their intention to market the EPR units to China in response to a request for vendor bids as well as their intent to pursue design certification in the United States under 10CFR52. The EPR safety philosophy is based on a deterministic consideration of defense-in-depth complemented by probabilistic analyses. Not only is the EPR designed to prevent and mitigate design basis accidents (DBAs), it employs an extra level of safety associated with severe accident response. Therefore, as a design objective, features are included to ensure that radiological consequences are limited such that the need for stringent counter measures, such as evacuation and relocation of the nearby population, can be reasonably excluded. This paper discusses some of the innovative features of the EPR to address severe accident challenges. (author)

Analyses of severe accident scenarios in RBMK-1500

International Nuclear Information System (INIS)

Kaliatka, A.; Rimkevicius, S.; Uspuras, E.; Urbonavicius, E.

2006-01-01

Even though research of severe accidents in light water reactors is performed around the world for several decades many questions remain. Research is mostly performed for vessel-type reactors. RBMK is a channel type light water reactor, which differs from the vessel-type reactors in several aspects. These differences impose some specifics in the accident phenomena and processes that occur during severe accidents. Severe accident research for RBMK reactors is taking first steps and very little information is available in the open literature. The existing severe accident analysis codes are developed for vessel-type reactors and their application to the analysis of accidents in RBMK is not straightforward. This paper presents the results of an analysis of large loss-of-coolant accident scenarios with loss of coolant injection to the core of RBMK-1500. The analysis performed considers processes in the reactor core, in the reactor cooling system and in the confinement until the fuel melting started. This paper does not aim to answer all the questions regarding severe accidents in RBMK but rather to start a discussion, identify the expected timing of the key phenomena. (orig.)

Containment response to a severe accident (TMLB sequence) with and without mitigation strategies

International Nuclear Information System (INIS)

Passalacqua, R.

2004-01-01

A loss of SG feed-water (TMLB sequence) for a prototypic PWR 900 MWe with a multi-compartment configuration (with 11 and 16 cells nodalization) has been calculated by the author using the ASTEC code in the frame of the EVITA project (5th Framework Programme, FWP). A variety of hypothesis (e.g. activation of sprays and hydrogen recombiners) and possible consequences of these assumptions (cavity flooding, hydrogen combustion, etc.) have been made in order to evaluate the global reactor containment building response (pressure, aerosol/FP concentration, etc.). The need to dispose of severe accident management guidelines (SAMGs) is increasing. These guidelines are meant for nuclear plants' operators in order to allow them to apply mitigation strategies all along a severe accident, which, only in its initial phase, may last several days. The purpose of this paper is to outline the influence on the containment load of most common accident occurrences and operators actions, which is essential in establishing SAMGs. ASTEC (Accident Source Term Evaluation Code) is a computer code for the evaluation of the consequences of a postulated nuclear plant severe accident sequence. ASTEC is a computer tool currently under joint development by the Institut de Radioprotection et de Surete Nucleaire (IRSN), France, and Gesellschaft fuer Anlagen-und Reaktorsicherheit (GRS), Germany. The aim of the development is to create a fast running integral code package, reliable in all simulations of a severe accident, to be used for level-2 PSA analysis. It must be said that several recent developments have significantly improved the best-estimate models of ASTEC and a new version (ASTEC V1.0) has been released mid-2002. Nevertheless, the somehow obsolete ASTECv0.3 version here used, has given results very useful for the estimation of the global risk of a nuclear plant. Moreover, under the current 6th FWP (Sustainable Integration of EU Research on Severe Accident Phenomenology and Management), the

Application of the accident management information needs methodology to a severe accident sequence

International Nuclear Information System (INIS)

Ward, L.W.; Hanson, D.J.; Nelson, W.R.; Solberg, D.E.

1989-01-01

The U.S. Nuclear Regulatory Commission is conducting an accident management research program that emphasizes the use of severe accident research to enhance the ability of plant operating personnel to effectively manage severe accidents. Hence, it is necessary to ensure that the plant instrumentation and information systems adequately provide this information to the operating staff during accident conditions. A methodology to identify and assess the information needs of the operating staff of a nuclear power plant during a severe accident has been developed. The methodology identifies (a) the information needs of the plant personnel during a wide range of accident conditions, (b) the existing plant measurements capable of supplying these information needs and minor additions to instrument and display systems that would enhance management capabilities, (c) measurement capabilities and limitations during severe accident conditions, and (d) areas in which the information systems could mislead plant personnel

Application of the accident management information needs methodology to a severe accident sequence

Energy Technology Data Exchange (ETDEWEB)

Ward, L.W.; Hanson, D.J.; Nelson, W.R. (Idaho National Engineering Laboratory, Idaho Falls (USA)); Solberg, D.E. (Nuclear Regulatory Commission, Washington, DC (USA))

1989-11-01

The U.S. Nuclear Regulatory Commission is conducting an accident management research program that emphasizes the use of severe accident research to enhance the ability of plant operating personnel to effectively manage severe accidents. Hence, it is necessary to ensure that the plant instrumentation and information systems adequately provide this information to the operating staff during accident conditions. A methodology to identify and assess the information needs of the operating staff of a nuclear power plant during a severe accident has been developed. The methodology identifies (a) the information needs of the plant personnel during a wide range of accident conditions, (b) the existing plant measurements capable of supplying these information needs and minor additions to instrument and display systems that would enhance management capabilities, (c) measurement capabilities and limitations during severe accident conditions, and (d) areas in which the information systems could mislead plant personnel.

Severe accident mitigation through containment design

International Nuclear Information System (INIS)

Bergeron, K.D.

1990-01-01

Recent U.S. Department of Energy plans to construct a Heavy Water Reactor for the production of defense nuclear materials have created a unique opportunity to explore ways to mitigate severe accident concerns in the design stage. Drawing on an extensive background in US-NRC-sponsored severe accident work, Sandia National Laboratories has been exploring a number of Heavy Water New Production Reactor (HW-NPR) containment design strategies that might mitigate the consequences of a core-melt accident without greatly impacting construction cost or reactor operations. Severe accident specialists have undertaken these assessments with the intent of providing the plant designers with some of the phenomenological advantages and disadvantages of various mitigation strategies. This paper will highlight some of the more interesting concepts and summarize the results obtained. (author). 9 refs., 2 tabs

Severe accident mitigation through containment design

International Nuclear Information System (INIS)

Bergeron, K.D.

1990-01-01

Recent US Department of Energy plans to construct a Heavy Water Reactor for the production of defense nuclear materials have created a unique opportunity to explore ways to mitigate severe accident concerns in the design stage. Drawing on an extensive background in USNRC-sponsored severe accident work, Sandia National Laboratories has been exploring a number of Heavy Water New Production Reactor (HW-NPR) containment design strategies that might mitigate the consequences of a core-melt accident without greatly impacting construction cost or reactor operations. Severe accident specialists have undertaken these assessments with the intent of providing the plant designers with some of the phenomenological advantages and disadvantages of various mitigation strategies. This paper will highlight some of the more interesting concepts and summarize the results obtained. 9 refs., 2 tabs

Phenomena occurring in the reactor coolant system during severe core damage accidents

International Nuclear Information System (INIS)

Malinauskas, A.P.

1989-01-01

The reactor coolant system (RCS) of a nuclear power plant consists of the reactor pressure vessel and the piping and associated components that are required for the continuous circulation of the coolant which is used to maintain thermal equilibrium throughout the system. In the event of an accident, the RCS also serves as one of several barriers to the escape of radiotoxic material into the biosphere. In contrast to normal operating conditions, severe core damage accidents are characterized by significant temporal and spatial variations in heat and mass fluxes, and by eventual geometrical changes within the RCS. Furthermore, the difficulties in describing the system in the severe accident mode are compounded by the occurrence of chemical reactions. These reactions can influence both the thermal and the mass transport behavior of the system. In addition, behavior of the reactor vessel internals and of materials released from the core region (especially the radioactive fission products) in the course of the accident likewise become of concern to the analyst. This report addresses these concerns. 9 refs., 1 tab

Quantification of severe accident source terms of a Westinghouse 3-loop plant

International Nuclear Information System (INIS)

Lee Min; Ko, Y.-C.

2008-01-01

Integrated severe accident analysis codes are used to quantify the source terms of the representative sequences identified in PSA study. The characteristics of these source terms depend on the detail design of the plant and the accident scenario. A historical perspective of radioactive source term is provided. The grouping of radionuclides in different source terms or source term quantification tools based on TID-14844, NUREG-1465, and WASH-1400 is compared. The radionuclides release phenomena and models adopted in the integrated severe accident analysis codes of STCP and MAAP4 are described. In the present study, the severe accident source terms for risk quantification of Maanshan Nuclear Power Plant of Taiwan Power Company are quantified using MAAP 4.0.4 code. A methodology is developed to quantify the source terms of each source term category (STC) identified in the Level II PSA analysis of the plant. The characteristics of source terms obtained are compared with other source terms. The plant analyzed employs a Westinghouse designed 3-loop pressurized water reactor (PWR) with large dry containment

Introduction to Large-sized Test Facility for validating Containment Integrity under Severe Accidents

International Nuclear Information System (INIS)

Na, Young Su; Hong, Seongwan; Hong, Seongho; Min, Beongtae

2014-01-01

An overall assessment of containment integrity can be conducted properly by examining the hydrogen behavior in the containment building. Under severe accidents, an amount of hydrogen gases can be generated by metal oxidation and corium-concrete interaction. Hydrogen behavior in the containment building strongly depends on complicated thermal hydraulic conditions with mixed gases and steam. The performance of a PAR can be directly affected by the thermal hydraulic conditions, steam contents, gas mixture behavior and aerosol characteristics, as well as the operation of other engineering safety systems such as a spray. The models in computer codes for a severe accident assessment can be validated based on the experiment results in a large-sized test facility. The Korea Atomic Energy Research Institute (KAERI) is now preparing a large-sized test facility to examine in detail the safety issues related with hydrogen including the performance of safety devices such as a PAR in various severe accident situations. This paper introduces the KAERI test facility for validating the containment integrity under severe accidents. To validate the containment integrity, a large-sized test facility is necessary for simulating complicated phenomena induced by an amount of steam and gases, especially hydrogen released into the containment building under severe accidents. A pressure vessel 9.5 m in height and 3.4 m in diameter was designed at the KAERI test facility for the validating containment integrity, which was based on the THAI test facility with the experimental safety and the reliable measurement systems certified for a long time. This large-sized pressure vessel operated in steam and iodine as a corrosive agent was made by stainless steel 316L because of corrosion resistance for a long operating time, and a vessel was installed in at KAERI in March 2014. In the future, the control systems for temperature and pressure in a vessel will be constructed, and the measurement system

The European PASSAM project. R and D outcomes towards enhanced severe accident source term mitigation

International Nuclear Information System (INIS)

Albiol, T.; Herranz, L.; Riera, E.; Dalibart, C.; Lind, T.; Corno, A. Del; Kärkelä, T.; Losch, N.; Azambre, B.

2017-01-01

The European PASSAM project (Passive and Active Systems on Severe Accident source term Mitigation) involved nine partners from six countries during four year (2013 - 2016): IRSN (project coordinator), EDF and University of Lorraine (France); CIEMAT and CSIC (Spain); PSI (Switzerland); RSE (Italy); VTT (Finland) and AREVA GmbH (Germany). It was mainly of an R and D experimental nature and aimed at investigating phenomena that might enhance source term mitigation in case of a severe accident in a LWR. Both already existing systems and innovative ones were experimentally studied. This paper presents the main outcomes of this project, including experimental results, understanding of phenomena and corresponding models and correlations with some preliminary analyses for potential use in severe accident management strategies, taking into account the passive or non-passive nature of the systems studied. Pool scrubbing represented the most studied domain of the PASSAM project. As an example of results, it was shown that gas hydrodynamics, at least in some relevant scenarios, is significantly different from what is nowadays encapsulated in severe accident analysis codes, particularly at high velocities and, that in the long run, maintaining an alkaline pH in the scrubber solution is absolutely necessary for preventing a delayed iodine release. Regarding sand bed filters plus metallic pre-filters, implemented on all French nuclear power plants, filtration efficiency for gaseous molecular and organic iodine was checked. Other experiments showed that under severe accident conditions, cesium iodide aerosols trapped in the sand filter are unstable and may constitute a delayed source term, which is not the case for CsI particles trapped on the metallic pre-filter. As innovative processes, both acoustic agglomeration and high pressure spray systems were studied mainly in the aim of leading to bigger particles upstream of filtered containment venting systems (FCVS), and so enhancing

Reactor Safety Gap Evaluation of Accident Tolerant Components and Severe Accident Analysis

International Nuclear Information System (INIS)

Farmer, Mitchell T.; Bunt, R.; Corradini, M.; Ellison, Paul B.; Francis, M.; Gabor, John D.; Gauntt, R.; Henry, C.; Linthicum, R.; Luangdilok, W.; Lutz, R.; Paik, C.; Plys, M.; Rabiti, Cristian; Rempe, J.; Robb, K.; Wachowiak, R.

2015-01-01

The overall objective of this study was to conduct a technology gap evaluation on accident tolerant components and severe accident analysis methodologies with the goal of identifying any data and/or knowledge gaps that may exist, given the current state of light water reactor (LWR) severe accident research, and additionally augmented by insights obtained from the Fukushima accident. The ultimate benefit of this activity is that the results can be used to refine the Department of Energy's (DOE) Reactor Safety Technology (RST) research and development (R&D) program plan to address key knowledge gaps in severe accident phenomena and analyses that affect reactor safety and that are not currently being addressed by the industry or the Nuclear Regulatory Commission (NRC).

Reactor Safety Gap Evaluation of Accident Tolerant Components and Severe Accident Analysis

Energy Technology Data Exchange (ETDEWEB)

Farmer, Mitchell T. [Argonne National Lab. (ANL), Argonne, IL (United States); Bunt, R. [Southern Nuclear, Atlanta, GA (United States); Corradini, M. [Univ. of Wisconsin, Madison, WI (United States); Ellison, Paul B. [GE Power and Water, Duluth, GA (United States); Francis, M. [Argonne National Lab. (ANL), Argonne, IL (United States); Gabor, John D. [Erin Engineering, Walnut Creek, CA (United States); Gauntt, R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Henry, C. [Fauske and Associates, Burr Ridge, IL (United States); Linthicum, R. [Exelon Corp., Chicago, IL (United States); Luangdilok, W. [Fauske and Associates, Burr Ridge, IL (United States); Lutz, R. [PWR Owners Group (PWROG); Paik, C. [Fauske and Associates, Burr Ridge, IL (United States); Plys, M. [Fauske and Associates, Burr Ridge, IL (United States); Rabiti, Cristian [Idaho National Lab. (INL), Idaho Falls, ID (United States); Rempe, J. [Rempe and Associates LLC, Idaho Falls, ID (United States); Robb, K. [Argonne National Lab. (ANL), Argonne, IL (United States); Wachowiak, R. [Electric Power Research Inst. (EPRI), Knovville, TN (United States)

2015-01-31

The overall objective of this study was to conduct a technology gap evaluation on accident tolerant components and severe accident analysis methodologies with the goal of identifying any data and/or knowledge gaps that may exist, given the current state of light water reactor (LWR) severe accident research, and additionally augmented by insights obtained from the Fukushima accident. The ultimate benefit of this activity is that the results can be used to refine the Department of Energy’s (DOE) Reactor Safety Technology (RST) research and development (R&D) program plan to address key knowledge gaps in severe accident phenomena and analyses that affect reactor safety and that are not currently being addressed by the industry or the Nuclear Regulatory Commission (NRC).

Multi-phase model development to assess RCIC system capabilities under severe accident conditions

Energy Technology Data Exchange (ETDEWEB)

Kirkland, Karen Vierow [Texas A & M Univ., College Station, TX (United States); Ross, Kyle [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Beeny, Bradley [Texas A & M Univ., College Station, TX (United States); Luthman, Nicholas [Texas A& M Engineering Experiment Station, College Station, TX (United States); Strater, Zachary [Texas A & M Univ., College Station, TX (United States)

2017-12-23

The Reactor Core Isolation Cooling (RCIC) System is a safety-related system that provides makeup water for core cooling of some Boiling Water Reactors (BWRs) with a Mark I containment. The RCIC System consists of a steam-driven Terry turbine that powers a centrifugal, multi-stage pump for providing water to the reactor pressure vessel. The Fukushima Dai-ichi accidents demonstrated that the RCIC System can play an important role under accident conditions in removing core decay heat. The unexpectedly sustained, good performance of the RCIC System in the Fukushima reactor demonstrates, firstly, that its capabilities are not well understood, and secondly, that the system has high potential for extended core cooling in accident scenarios. Better understanding and analysis tools would allow for more options to cope with a severe accident situation and to reduce the consequences. The objectives of this project were to develop physics-based models of the RCIC System, incorporate them into a multi-phase code and validate the models. This Final Technical Report details the progress throughout the project duration and the accomplishments.

Severe obesity and high blood pressure among children, Philadelphia health centers, 2010.

Science.gov (United States)

Nguyen, John V; Robbins, Jessica M; Houck, Kevin L; Nobis, Elizabeth A; Inman, Katelyn A; Khan, Khudsiya S; Robbins, Susan W

2014-04-01

Child obesity is a major health problem particularly affecting disadvantaged population groups. Severe obesity carries additional health risks for children. In the context of the childhood obesity epidemic, high blood pressure among children is of increasing concern. Chart reviews were carried out to examine the prevalence of severe obesity and its association with high blood pressure measurements among randomly selected patients aged 3 to 17 years who had well-child care visits at 8 public community health centers during 2010. A majority of the 691 patients reviewed were African American (58%); an additional 16% were Hispanic. The prevalence of severe obesity was 7.7% (95% confidence interval = 5.8% to 9.9%) and the prevalence of high blood pressure measurements was 17.5% (95% confidence interval = 14.8% to 20.6%). Patients who were severely obese were more than twice as likely as other children to have high blood pressure values. Severe obesity is associated with substantially increased frequency of high blood pressure measurements in children, and should be investigated further as a potential marker for hypertension in children. Primary care providers should be prepared to diagnose and treat hypertension in severely obese children.

The COLIMA experiment on aerosol retention in containment leak paths under severe nuclear accidents

Energy Technology Data Exchange (ETDEWEB)

Parozzi, Flavio, E-mail: flavio.parozzi@rse-web.it [RSE, Power Generation Department, via Rubattino 54, I-20134 Milano (Italy); Caracciolo, Eduardo D.J., E-mail: eduardo.caracciolo@rse-web.it [RSE, Power Generation Department, via Rubattino 54, I-20134 Milano (Italy); Journeau, Christophe, E-mail: christophe.journeau@cea.fr [CEA Cadarache (France); Piluso, Pascal, E-mail: pascal.piluso@cea.fr [CEA Cadarache (France)

2013-08-15

Highlights: ► Experiment investigating aerosol retention within concrete containment cracks under nuclear severe accident conditions. ► Provided representative conditions of the aerosols suspended inside the containment of PWRs under a severe accident. ► Prototypical aerosol particles generated with a thermite reaction and transported through the crack sample reproducing surface characteristics, temperature, pressure drop and gas leakage. ► The results indicate the significant retention due to zig-zag path. -- Abstract: CEA and RSE managed an experimental research concerning the investigation of aerosol retention within concrete containment cracks under severe accident conditions. The main experiment was carried out in November 2008 with aerosol generated from the COLIMA facility and a sample of cracked concrete with defined geometric characteristics manufactured by RSE. The facility provided representative conditions of the aerosols suspended inside the containment of PWRs under a severe accident. Prototypical aerosol particles were generated with a thermite reaction and transported through the crack sample, where surface characteristics, temperature, pressure drop and gas leakage were properly reproduced. The paper describes the approach adopted for the preparation of the cracked concrete sample and the dimensioning of the experimental apparatus, the test procedure and the measured parameters. The preliminary results, obtained from this single test, are also discussed in the light of the present knowledge about aerosol phenomena and the theoretical analyses of particle behaviour with the crack path.

[Severe parachuting accident. Analysis of 122 cases].

Science.gov (United States)

Krauss, U; Mischkowsky, T

1993-06-01

Based on a population of 122 severely injured patients the causes of paragliding accidents and the patterns of injury are analyzed. A questionnaire is used to establish a sport-specific profile for the paragliding pilot. The lower limbs (55.7%) and the lower parts of the spine (45.9%) are the most frequently injured parts of the body. There is a high risk of multiple injuries after a single accident because of the tremendous axial power. The standard of equipment is good in over 90% of the cases. Insufficient training and failure to take account of geographical and meteorological conditions are the main determinants of accidents sustained by paragliders, most of whom are young. Nevertheless, 80% of our patients want to continue paragliding. Finally some advice is given on how to prevent paragliding accidents and injuries.

Development of a totally integrated severe accident training system

International Nuclear Information System (INIS)

Kim, Ko Ryu; Park, Sun Hee; Choi, Young; Kim, Dong Ha

2006-01-01

Recently KAERI has developed the severe accident management guidance to establish the Korea standard severe accident management system. On the other hand the PC-based severe accident training simulator SATS has been developed, which uses the MELCOR code as the simulation engine. The simulator SATS graphically displays and simulates the severe accidents with interactive user commands. Especially the control capability of SATS could make a severe accident training course more interesting and effective. In this paper we will describe the development and functions of the electrical guidance module, HyperKAMG, and the SATS-HyperKAMG linkage system designed for a totally integrated and automated severe accident training. (author)

Sarnet lecture notes on nuclear reactor severe accident phenomenology

International Nuclear Information System (INIS)

Trambauer, K.; Adroguer, B.; Fichot, F.; Muller, C.; Meyer, L.; Breitung, W.; Magallon, D.; Journeau, C.; Alsmeyer, H.; Housiadas, C.; Clement, B.; Ang, M.L.; Chaumont, B.; Ivanov, I.; Marguet, S.; Van Dorsselaere, J.P.; Fleurot, J.; Giordano, P.; Cranga, M.

2008-01-01

The 'Severe Accident Phenomenology Short Course' is part of the Excellence Spreading activities of the European Severe Accident Research NETwork of Excellence SARNET (project of the EURATOM 6. Framework programme). It was held at Cadarache, 9-13 January 2006. The course was divided in 14 lectures covering all aspects of severe accident phenomena that occur during a scenario. It also included lectures on PSA-2, Safety Assessment and design measures in new LWR plants for severe accident mitigation (SAM). This book presents the lecture notes of the Severe Accident Phenomenology Short Course and condenses the essential knowledge on severe accident phenomenology in 2008. (authors)

Analysis of containment pressure and temperature changes following loss of coolant accident (LOCA)

International Nuclear Information System (INIS)

Nguyen Van Thai; Kieu Ngoc Dung

2015-01-01

This paper present a preliminary thermal-hydraulics analysis of AP1000 containment following loss of coolant accident events such as double-end cold line break (DECLB) or main steam line break (MSLB) using MELCOR code. A break of this type will produce a rapid depressurization of the reactor pressure vessel (primary system) and release initially high pressure water into the containment followed by a much smaller release of highly superheated steam. The high pressure liquid water will flash and rapidly pressurize the containment building. The performance of passive containment cooling system for steam removal by condensation on large steel containment structure is a major contributing process, controlling the pressure and temperature maximum reached during the accident event. The results are analyzed, discussed and compared with the similar work done by Sandia National Laboratories. (author)

Severe accident tests and development of domestic severe accident system codes

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-08-15

According to lessons learned from Fukushima-Daiichi NPS accidents, the safety evaluation will be started based on the NRA's New Safety Standards. In parallel with this movement, reinforcement of Severe Accident (SA) Measures and Accident Managements (AMs) has been undertaken and establishments of relevant regulations and standards are recognized as urgent subjects. Strengthening responses against nuclear plant hazards, as well as realistic protection measures and their standardization is also recognized as urgent subjects. Furthermore, decommissioning of Fukushima-Daiichi Unit1 through Unit4 is promoted diligently. Taking into account JNES's mission with regard to these SA Measures, AMs and decommissioning, movement of improving SA evaluation methodologies inside and outside Japan, and prioritization of subjects based on analyses of sequences of Fukushima-Daiichi NPS accidents, three viewpoints was extracted. These viewpoints were substantiated as the following three groups of R and D subjects: (1) Obtaining near term experimental subjects: Containment venting, Seawater injection, Iodine behaviors. (2) Obtaining mid and long experimental subjects: Fuel damage behavior at early phase of core degradation, Core melting and debris formation. (3) Development of a macroscopic level SA code for plant system behaviors and a mechanistic level code for core melting and debris formation. (author)

Severe accident tests and development of domestic severe accident system codes

International Nuclear Information System (INIS)

2013-01-01

According to lessons learned from Fukushima-Daiichi NPS accidents, the safety evaluation will be started based on the NRA's New Safety Standards. In parallel with this movement, reinforcement of Severe Accident (SA) Measures and Accident Managements (AMs) has been undertaken and establishments of relevant regulations and standards are recognized as urgent subjects. Strengthening responses against nuclear plant hazards, as well as realistic protection measures and their standardization is also recognized as urgent subjects. Furthermore, decommissioning of Fukushima-Daiichi Unit1 through Unit4 is promoted diligently. Taking into account JNES's mission with regard to these SA Measures, AMs and decommissioning, movement of improving SA evaluation methodologies inside and outside Japan, and prioritization of subjects based on analyses of sequences of Fukushima-Daiichi NPS accidents, three viewpoints was extracted. These viewpoints were substantiated as the following three groups of R and D subjects: (1) Obtaining near term experimental subjects: Containment venting, Seawater injection, Iodine behaviors. (2) Obtaining mid and long experimental subjects: Fuel damage behavior at early phase of core degradation, Core melting and debris formation. (3) Development of a macroscopic level SA code for plant system behaviors and a mechanistic level code for core melting and debris formation. (author)

Addressing severe accidents in the CANDU 9 design

International Nuclear Information System (INIS)

Nijhawan, S.M.; Wight, A.L.; Snell, V.G.

1998-01-01

CANDU 9 is a single-unit evolutionary heavy-water reactor based on the Bruce/Darlington plants. Severe accident issues are being systematically addressed in CANDU 9, which includes a number of unique features for prevention and mitigation of severe accidents. A comprehensive severe accident program has been formulated with feedback from potential clients and the Canadian regulatory agency. Preliminary Probabilistic Safety Analyses have identified the sequences and frequency of system and human failures that may potentially lead to initial conditions indicating onset of severe core damage. Severe accident consequence analyses have used these sequences as a guide to assess passive heat sinks for the core, and containment performance. Estimates of the containment response to mass and energy injections typical of postulated severe accidents have been made and the results are presented. We find that inherent CANDU severe accident mitigation features, such as the presence of large water volumes near the fuel (moderator and shield tank), permit a relatively slow severe accident progression under most plant damage states, facilitate debris coolability and allow ample time for the operator to arrest the progression within, progressively, the fuel channels, calandria vessel or shield tank. The large-volume CANDU 9 containment design complements these features because of the long times to reach failure

Development of severe accident management advisory and training simulator (SAMAT)

International Nuclear Information System (INIS)

Jeong, K.-S.; Kim, K.-R.; Jung, W.-D.; Ha, J.-J.

2002-01-01

The most operator support systems including the training simulator have been developed to assist the operator and they cover from normal operation to emergency operation. For the severe accident, the overall architecture for severe accident management is being developed in some developed countries according to the development of severe accident management guidelines which are the skeleton of severe accident management architecture. In Korea, the severe accident management guideline for KSNP was recently developed and it is expected to be a central axis of logical flow for severe accident management. There are a lot of uncertainties in the severe accident phenomena and scenarios and one of the major issues for developing a operator support system for a severe accident is the reduction of these uncertainties. In this paper, the severe accident management advisory system with training simulator, SAMAT, is developed as all available information for a severe accident are re-organized and provided to the management staff in order to reduce the uncertainties. The developed system includes the graphical display for plant and equipment status, the previous research results by knowledge-base technique, and the expected plant behavior using the severe accident training simulator. The plant model used in this paper is oriented to severe accident phenomena and thus can simulate the plant behavior for a severe accident. Therefore, the developed system may make a central role of the information source for decision-making for a severe accident management, and will be used as the training simulator for severe accident management

Portable Filtered Air Suction System for Released Radioactive Gases Prevention under a Severe Accident of NPPs

International Nuclear Information System (INIS)

Gu, Beom W.; Choi, Su Y.; Rim, Chun T.

2013-01-01

In this paper, the portable filtered air suction system (PoFASS) for released radioactive gases prevention under a severe accident of NPP is proposed. This technology can prevent the release of the radioactive gases to the atmosphere and it can be more economical than FVCS because PoFASS can cover many NPPs with its high mobility. The conceptual design of PoFASS, which has the highest cost effectiveness and robustness to the environment condition such as wind velocity and precipitation, is suggested and the related previous research is introduced in this paper. The portable filtered air suction system (PoFASS) for released radioactive gases prevention can play a key role to mitigate the severe accident of NPP with its high cost effectiveness and robustness to the environment conditions. As further works, the detail design of PoFASS to fabricate a prototype for a demonstration will be proceeded. When released radioactive gases from the broken containment building in the severe accident of nuclear power plants (NPPs) such as the Chernobyl and Fukushima accidents occur, there are no ways to prevent the released radioactive gases spreading in the air. In order to solve this problem, several European NPPs have adopted the filtered vented containment system (FVCS), which can avoid the containment failure through a pressure relief capability to protect the containment building against overpressure. However, the installation cost of FVCS for a NPP is more than $10 million and this system has not been widely welcomed by NPP operating companies due to its high cost

Preliminary thermal design of a pressurized water reactor containment for handling severe accident consequences

International Nuclear Information System (INIS)

Abdullah, A.M.; Karameldin, A.

1998-01-01

A one-dimensional mathematical model has been developed for a 4250 MW(th) Advanced Pressurized Water Reactor containment analysis following a severe accident. The cooling process of the composite containment-steel shell and concrete shield- is achievable by natural circulation of atmospheric air. However, for purpose of gettering higher degrees of safety margin, the present study undertakes two objectives: (1) Installment of a diesel engine-driven air blower to force air through the annular space between the steel shell and concrete shield. The engine can be remotely operated to be effective in case of station blackout. (ii) Fixing longitudinally plate fins on the circumference of the inside and outside containment steel shell. These fins increase the heat transfer areas and hence the rate of heat removal from the containment atmosphere. In view of its importance - from the safety viewpoint - the long term behaviour of the containment which is a quasi-steady state problem, is formulated through a system of coupled nonlinear algebraic equations which describe the thermal-hydraulic and thermodynamic behaviour of the double shell containment. The calculated results revealed the following: (i) the passively air cooled containment can remove maximum heat load of 11.5 MW without failure, (ii) the effect of finned surface in the air passage tends to decrease the containment pressure by 20 to 30%, depending on the heat load, (iii) the effect of condensing fins is negligible for the proposed fin dimensions and material. However, by reducing the fin width, increasing their thickness, doubling their number, and using a higher conductive metal than the steel, it is expected that the containment pressure can be further reduced by 10% or more, (iv) the fins' dimensions and their number must be optimized via maximizing the difference or the ratio between the heat removed and pressure drop to get maximum heat flow rate

Swedish approach to information needs in severe accident situations

Energy Technology Data Exchange (ETDEWEB)

Soederman, E. (ES-Konsult AB, Stockholm (Sweden)); Karnik, P. (ES-Konsult AB, Stockholm (Sweden))

1992-07-01

In Sweden, systems for mitigating severe accidents have been installed at all plants and procedures have been implemented for accident management. This work has included the assessment of needs of information and the survivability of existing instrumentation during the various phases of an accident scenario. The approach has been pragmatic and based on existing knowledge of accident phenomenology and MAAP code calculations together with plant staff experience of detailed plant design and installation. During the early phases of accidents, which is defined to remain up to maximum fuel temperatures in the order of 800 C, the ordinary instrumentation is to a great extent useful. The reactor vessel level measurement is however identified to be weak in BWRs as soon as the core is partly uncovered. This has lead to the development of a Core Cooling Monitor. In later phases of accident scenarios, the general basis has been that no intrumentation inside the containment can survive. It has been analysed what information is strictly needed. It has been found that detailed information of the status inside the pressure vessel is of little importance after vessel penetration. Certain important information needs have been identified, that was not safely accessible from existing instrumentation. This had lead to complementary installations, using instruments inserted into the containment through protected guide tubes. Also for sampling of gas and water complementary installations have been made. (orig.)

Swedish approach to information needs in severe accident situations

International Nuclear Information System (INIS)

Soederman, E.; Karnik, P.

1992-01-01

In Sweden, systems for mitigating severe accidents have been installed at all plants and procedures have been implemented for accident management. This work has included the assessment of needs of information and the survivability of existing instrumentation during the various phases of an accident scenario. The approach has been pragmatic and based on existing knowledge of accident phenomenology and MAAP code calculations together with plant staff experience of detailed plant design and installation. During the early phases of accidents, which is defined to remain up to maximum fuel temperatures in the order of 800 C, the ordinary instrumentation is to a great extent useful. The reactor vessel level measurement is however identified to be weak in BWRs as soon as the core is partly uncovered. This has lead to the development of a Core Cooling Monitor. In later phases of accident scenarios, the general basis has been that no intrumentation inside the containment can survive. It has been analysed what information is strictly needed. It has been found that detailed information of the status inside the pressure vessel is of little importance after vessel penetration. Certain important information needs have been identified, that was not safely accessible from existing instrumentation. This had lead to complementary installations, using instruments inserted into the containment through protected guide tubes. Also for sampling of gas and water complementary installations have been made. (orig.)

CANDU severe accident management guidance update

International Nuclear Information System (INIS)

Jones, L.; Popov, N.; Gilbert, L.; Weed, J.

2014-01-01

The CANDU Owners Group (COG) developed a set of generic and initial station-specific Severe Accident Management Guidance (SAMG) documents to mitigate the consequences to the public in the event of a severe accident. The generic portion of the COG SAMG was completed in 2006; the overall project including the station-specific phase was completed in April 2007. Over the years, the CANDU industry and utilities have continuously increased the knowledge base for SAMG and have incorporated various engineered features based on the knowledge obtained. As a result of the event that occurred at the Fukushima Daiiachi nuclear power plant (NPP) in Japan, the Canadian Nuclear Safety Commission (CNSC) established the CNSC Fukushima Task Force. The results of the task force were documented in INFO-0828, CNSC Staff Action Plan on the CNSC Fukushima Task Force Recommendations. Among the recommendation documented in INFO-828 were Fukushima Action Items (FAIs) directed towards the CANDU utilities in Canada; a portion of which are related to SAMG documentation updates and directed at enhancing SAM response. A COG joint project was established to support the closure of the CNSC FAIs and to revise the current CANDU documentation accordingly. This paper provides a high level summary of the COG project scope and results. It also demonstrates that the CANDU SAMG programs in Canada provide robust protection and mitigation of severe accidents. (author)

CANDU severe accident management guidance update

Energy Technology Data Exchange (ETDEWEB)

Jones, L., E-mail: lisa.m.jones@opg.com [Ontario Power Generation, Pickering, ON (Canada); Popov, N., E-mail: nik.popov@rogers.com [Candu Owners Group, Toronto, ON (Canada); Gilbert, L., E-mail: lovell.gilbert@brucepower.com [Bruce Power, Tiverton, ON (Canada); Weed, J., E-mail: jeff.weed@candu.gov [Candu Owners Group, Toronto, ON (Canada)

2014-07-01

The CANDU Owners Group (COG) developed a set of generic and initial station-specific Severe Accident Management Guidance (SAMG) documents to mitigate the consequences to the public in the event of a severe accident. The generic portion of the COG SAMG was completed in 2006; the overall project including the station-specific phase was completed in April 2007. Over the years, the CANDU industry and utilities have continuously increased the knowledge base for SAMG and have incorporated various engineered features based on the knowledge obtained. As a result of the event that occurred at the Fukushima Daiiachi nuclear power plant (NPP) in Japan, the Canadian Nuclear Safety Commission (CNSC) established the CNSC Fukushima Task Force. The results of the task force were documented in INFO-0828, CNSC Staff Action Plan on the CNSC Fukushima Task Force Recommendations. Among the recommendation documented in INFO-828 were Fukushima Action Items (FAIs) directed towards the CANDU utilities in Canada; a portion of which are related to SAMG documentation updates and directed at enhancing SAM response. A COG joint project was established to support the closure of the CNSC FAIs and to revise the current CANDU documentation accordingly. This paper provides a high level summary of the COG project scope and results. It also demonstrates that the CANDU SAMG programs in Canada provide robust protection and mitigation of severe accidents. (author)

Steam Oxidation Testing in the Severe Accident Test Station

Energy Technology Data Exchange (ETDEWEB)

Pint, Bruce A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-08-01

After the March 2011 accident at Fukushima Daiichi, Oak Ridge National Laboratory (ORNL) began conducting high temperature steam oxidation testing of candidate materials for accident tolerant fuel (ATF) cladding in August 2011 [1-11]. The ATF concept is to enhance safety margins in light water reactors (LWR) during severe accident scenarios by identifying materials with 100× slower steam oxidation rates compared to current Zr-based alloys. In 2012, the ORNL laboratory equipment was expanded and made available to the entire ATF community as the Severe Accident Test Station (SATS) [4,12]. Compared to the current UO2/Zr-based alloy fuel system, an ATF alternative would significantly reduce the rate of heat and hydrogen generation in the core during a coolant-limited severe accident [13-14]. The steam oxidation behavior of candidate materials is a key metric in the evaluation of ATF concepts and also an important input into models [15-17]. However, initial modeling work of FeCrAl cladding has used incomplete information on the physical properties of FeCrAl. Also, the steam oxidation data being collected at 1200°-1700°C is unique as no prior work has considered steam oxidation of alloys at such high temperatures. Also, because many accident scenarios include steadily increasing temperatures, the required data are not traditional isothermal exposures but exposures with varying “ramp” rates. In some cases, the steam oxidation behavior has been surprising and difficult to interpret. Thus, more fundamental information continues to be collected. In addition, more work continues to focus on commercially-manufactured tube material. This report summarizes recent work to characterize the behavior of candidate alloys exposed to high temperature steam, evaluate steam oxidation behavior in various ramp scenarios and continue to collect integral data on FeCrAl compared to conventional Zr-based cladding.

Light water reactor severe accident seminar. Seminar presentation manual

International Nuclear Information System (INIS)

2004-01-01

The topics covered in this manual on LWR severe accidents were: Evolution of Source Term Definition and Analysis, Current Position on Severe Accident Phenomena, Current Position on Fission Product Behavior, Overview of Software Models Used in Severe Accident Analysis, Overview of Plant Specific Source Terms and Their Impact on Risk, Current Applications of Severe Accident Analysis, and Future plans

Light water reactor severe accident seminar. Seminar presentation manual

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

The topics covered in this manual on LWR severe accidents were: Evolution of Source Term Definition and Analysis, Current Position on Severe Accident Phenomena, Current Position on Fission Product Behavior, Overview of Software Models Used in Severe Accident Analysis, Overview of Plant Specific Source Terms and Their Impact on Risk, Current Applications of Severe Accident Analysis, and Future plans.

Use of simulators in severe accident management

International Nuclear Information System (INIS)

Evans, R.C.

1994-01-01

The U.S. nuclear utility industry is moving in a deliberate fashion through a coordinated industry severe accident working group to study and augment, where appropriate, the existing utility organizational and emergency planning structure to address accident and severe accident management. Full-scope simulators are used extensively to train licensed operators for their initial license examinations and continually thereafter in licensed operator requalification training and yearly examinations. The goal of the training (both initial and requalification) is to ensure that operators possess adequate knowledge, skills and abilities to prevent an event from progressing to core damage. The use of full-scope simulators in severe accident management training is in large part viewed by the industry as being premature. The working group study has not progressed to the point where the decision to employ full-scope simulators can be logically considered. It is not however premature to consider part-task or work station simulators as invaluable research tools to support the industry's study. These simulators could be employed, subject to limitations in the current state of knowledge regarding severe accident progression and phenomenological responses, in the validation and verification (V and V) of severe accident models or codes as they are developed. The U.S. nuclear utility industry has made substantial strides in the past 12 years in the accident prevention, mitigation and management arena. These strides are a product of the industry's preference for a logical and systematic approach to change. (orig.)

A study on the hydrogen behavior and its mitigation in the APR1400 containment during a severe accident

International Nuclear Information System (INIS)

Kim, Jong Tae; Hong, Seong Wan; Park, Rae Joon; Kim, Sang Baik

2005-02-01

During a hypothetical severe accident in a nuclear power plant (NPP), hydrogen is generated by the active reaction of fuel-cladding and steam in the reactor pressure vessel and released with steam into the containment. In this study, the analysis of the hydrogen and steam behavior during selected severe accidents in the APR1400 containment has been conducted by using the GASFLOW code. For the SBLOCA, hydrogen was accumulated in the containment dome region quickly when only PARSs were used. When the igniters were turned on, a standing flame was formed around a coolant pump and burnt most of the hydrogen blown-out. For the TLOFW accident, the flap-type pressure damper installed at the IRWST vents strongly affected the flow structure of the hydrogen. And by the steam-rich and oxygen starvation conditions in the IRWST, DDT is not likely to occur. For the SBO accident, dry hydrogen was release in the IRWST by the assumption of full condensation of the released steam in the IRWST water. In this case, the possibility of flame acceleration is high in the IRWST and annular compartment. In this study two design modifications were proposed in view of the hydrogen mitigation strategy and their effectiveness was evaluated by the GASFLOW analysis

A review of severe accident assessment

International Nuclear Information System (INIS)

Kawashima, Kei

2000-01-01

One of the most difficult problems on evaluation of external costs on nuclear power generation is value on a severe accident risk. Once forming a severe accident, its effect is very important and extends to a wide range, to give a lot of damages. It is a main area of study on externality of energy to compare various risks by means of price conversion at unit kWh. Here was outlined on research examples on main severe accident risks before then. A common fact on estimation cost such research examples is to limit it to direct cost (mainly to health damage) at accident phenomenon. As an actual problem, it is very difficult to substantially quantify such parameters because of basically belonging to social psychology. It is due to no finding out decisive evaluation method on this problem to be adopted conventional EED (Expert Expected Damages) approach in the ExternE Phase III, either. (G.K.)

Study Of Severe Accident Phenomena In Nuclear Power Plant

International Nuclear Information System (INIS)

Sugiyanto; Antariksawan; Anhar, R.; Arifal

2001-01-01

Several phenomena that occurred in the light water reactor type of nuclear power plant during severe accident were studied. The study was carried out based on the results of severe accident researches in various countries. In general, severe accident phenomena can be classified into in-vessel phenomena, retention in the reactor coolant system, and ex-vessel phenomena. In-vessel retention has been recommended as a severe accident management strategy

Severe accident sequence assessment for boiling water reactors: program overview

International Nuclear Information System (INIS)

Fontana, M.H.

1980-10-01

The Severe Accident Sequence Assessment (SASA) Program was started at the Oak Ridge National Laboratory (ORNL) in June 1980. This report documents the initial planning, specification of objectives, potential uses of the results, plan of attack, and preliminary results. ORNL was assigned the Brown's Ferry Unit 1 Plant with the station blackout being the initial sequence set to be addressed. This set includes: (1) loss of offsite and onsite ac power with no coolant injection; and (2) loss of offsite and onsite ac power with high pressure coolant injection (HPCI) and reactor core isolation cooling (RCIC) as long as dc power supply lasts. This report includes representative preliminary results for the former case

Application of FFTBM to severe accidents

International Nuclear Information System (INIS)

Prosek, A.; Leskovar, M.

2005-01-01

In Europe an initiative for the reduction of uncertainties in severe accident safety issues was initiated. Generally, the error made in predicting plant behaviour is called uncertainty, while the discrepancies between measured and calculated trends related to experimental facilities are called the accuracy of the prediction. The purpose of the work is to assess the accuracy of the calculations of the severe accident International Standard Problem ISP-46 (Phebus FPT1), performed with two versions of MELCOR 1.8.5 for validation purposes. For the quantitative assessment of calculations the improved fast Fourier transform based method (FFTBM) was used with the capability to calculate time dependent code accuracy. In addition, a new measure for the indication of the time shift between the experimental and the calculated signal was proposed. The quantitative results obtained with FFTBM confirm the qualitative conclusions made during the Jozef Stefan Institute participation in ISP-46. In general good agreement of thermal-hydraulic variables and satisfactory agreement of total releases for most radionuclide classes was obtained. The quantitative FFTBM results showed that for the Phebus FPT1 severe accident experiment the accuracy of thermal-hydraulic variables calculated with the MELCOR severe accident code is close to the accuracy of thermal-hydraulic variables for design basis accident experiments calculated with best-estimate system codes. (author)

Implementation of hydrogen mitigation techniques during severe accidents in nuclear power plants

International Nuclear Information System (INIS)

1996-01-01

Severe accidents in water-cooled reactors are low-probability events as the Emergency Core Cooling System (ECCS) has been designed and specific accident management measures have been implemented to prevent severe accidents from occurring. Should it not be possible to prevent a severe accident in a water-cooled reactor, a large amount of hydrogen could be generated, notably from the reaction between steam and zirconium at high fuel clad temperatures, but also from reactions of molten core debris with concrete, water radiolysis, and reactions of structural materials with steam. The rates and quantities of hydrogen produced depend on the particular severe accident scenario and also on the reactor type (e.g. mass of zirconium in the reactor core). Depending on assumptions made, and taking account of various uncertainties, release rates of hydrogen up to several kg/s have been calculated with total hydrogen mass releases ranging from 100 kg to more than 1,000 kg for large reactors. Hydrogen produced during a severe accident could burn close to the hydrogen source or would mix with the containment atmosphere and burn if flammable concentrations are attained and ignition sources are available (e.g., igniters, accidental sparks from electric equipment). If oxygen and ignition sources are present in the vicinity of the release, the hydrogen will ignite and it could burn as a standing flame at the release location, which is possible over a large range of jet exit diameters, jet velocities and environmental conditions. The hydrogen that will not burn close to the source will mix with steam and air and will transport in the containment building to increase global or local concentrations and to create possibly flammable conditions. If ignited at high enough hydrogen concentration, the mixture could burn as a deflagration, creating a transient pressure and temperature that could possibly challenge the containment integrity and equipment. In regions of higher hydrogen

Development of a severe accident training simulator using a MELCOR code

International Nuclear Information System (INIS)

Kim, Ko Ryu; Jeong, Kwang Sub; Ha, Jae Joo; Jung, Won Dae

2002-03-01

Nuclear power plants' severe accidents are, despite of their rareness, very important in safety aspects, because of their huge damages when occurred. For the appropriate execution of severe accident strategy, more information for decision-making are required because of the uncertainties included in severe accidents. Earlier NRC raised concerns over severe accident training in the report NUREC/CR-477, and accordingly, developing effective training tools for severe accident were emphasized. In fact the training tools were requested from industrial area, nevertheless, few training tools were developed due to the uncertainties in severe accidents, lacks of analysis computer codes and technical limitations. SATS, the severe accident training simulator, is developed as a multi-purpose tools for severe accident training. SATS uses the calculation results of MELCOR, an integral severe accident analysis code, and with the help of SL-GMS graphic tools, provides dynamic displays of severe accident phenomena on the terminal of IBM PC. It aimed to have two main features: one is to provide graphic displays to represent severe accident phenomena and the other is to process and simulate severe accident strategy given by plant operators and TSC staffs. Severe accident strategies are basically composed of series of operations of available pumps, valves and other equipments. Whenever executing strategies with SATS, the trainee should follow the HyperKAMG, the on line version of the recently developed severe accident guidance (KAMG). Severe accident strategies are closely related to accidents scenarios. TLOFW and LOCA , two representative severe accident scenarios of Uljin 3,4, are developed as a built-in scenarios of SATS. Although SATS has some minor problems at this time, we expect SATS will be a good severe accident training tool after the appropriate addition of accident scenarios. Moreover, we also expect SATS will be a good advisory tool for the severe accident research

Establishment of Technical Collaboration basis between Korea and France for the development of severe accident assessment computer code under high burnup condition

International Nuclear Information System (INIS)

Kim, H. D.; Kim, D. H.; Park, S. Y.; Park, J. H.

2005-10-01

This project was performed by KAERI in the frame of construction of the international cooperative basis on the nuclear energy. This was supported from MOST under the title of 'Establishment of Technical Collaboration basis between Korea and France for the development of severe accident assessment computer code under high burn up condition'. The current operating NPP are converting the burned fuel to the wasted fuel after burn up of 40 GWD/MTU. But in Korea, burn up of more than 60 GWD/MTU will be expected because of the high fuel efficiency but also cost saving for storing the wasted fuel safely. The domestic research for the purpose of developing the fuel and the cladding that can be used under the high burn up condition up to 100 GWD/MTU is in progress now. But the current computer code adopts the model and the data that are valid only up to the 40 GWD/MTU at most. Therefore the current model could not take into account the phenomena that may cause differences in the fission product release behavior or in the core damage process due to the high burn up operation (more than 40 GWD/MTU). To evaluate the safety of the NPP with the high burn up fuel, the improvement of current severe accident code against the high burn up condition is an important research item. Also it should start without any delay. Therefore, in this study, an expert group was constructed to establish the research basis for the severe accident under high burn up conditions. From this expert group, the research items regarding the high burn up condition were selected and identified through discussion and technical seminars. Based on these selected items, the meeting between IRSN and KAERI to find out the cooperative research items on the severe accident under the high burn up condition was held in the IRSN headquater in Paris. After the meeting, KAERI and IRSN agreed to cooperate with each other on the selected items, and to co-host the international seminar, and to develop the model and to

Evaluation of the leakage behavior of inflatable seals subject to severe accident conditions

International Nuclear Information System (INIS)

Parks, M.B.

1989-11-01

Sandia National Laboratories, under the sponsorship of the United States Nuclear Regulatory Commission, is currently developing test validated methods to predict the pressure capacity of light water reactor containment buildings when subjected to postulated severe accident conditions. These conditions are well beyond the design basis. Scale model tests of steel and reinforced concrete containments have been conducted as well as tests of typical containment penetrations. As a part of this effort, a series of tests was recently conducted to determine the leakage behavior of inflatable seals. These seals are used to prevent leakage around personnel and escape lock doors of some containments. The results of the inflatable seals tests are the subject of this report. Inflatable seals were tested at both room temperature and at elevated temperatures representative of postulated severe accident conditions. Both aged (radiation and thermal) and unaged seals were included in the test program. The internal seal pressure at the beginning of each test was varied to cover the range of seal pressures actually used in containments. For each seal pressure level, the external (containment) pressure was increased until significant leakage past the seals was observed. Parameters that were monitored and recorded during the tests were the internal seal pressure, chamber pressure, leakage past the seals, and temperature of the test chamber and fixture to which the seals were attached. 8 refs., 34 figs., 7 tabs

Plant accident dynamics of high-temperature reactors with direct gas turbine cycle

International Nuclear Information System (INIS)

Waloch, M.L.

1977-01-01

In the paper submitted, a one-dimensional accident simulation model for high-temperature reactors with direct-cycle gas turbine (single-cycle facilities) is described. The paper assesses the sudden failure of a gas duct caused by the double-ended break of one out of several parallel pipes before and behind the reactor for a non-integrated plant, leading to major loads in the reactor region, as well as the complete loss of vanes of the compressor for an integrated plant. The results of the calculations show especially high loads for the break of a hot-gas pipe immediately behind the flow restrictors of the reactor outlet, because of prolonged effects of pressure gradients in the reactor region and the maximum core differential pressure. A plant accident dynamics calculation therefore allows to find a compromise between the requirements of stable compressor operation, on the one hand, and small loads in the reactor in the course of an accident, on the other, by establishing in a co-ordinated manner the narrowing ratio of the flow restrictors. (GL) [de

Radionuclide release calculations for selected severe accident scenarios. Volume 3. PWR, subatmospheric containment design

International Nuclear Information System (INIS)

Denning, R.S.; Gieseke, J.A.; Cybulskis, P.; Lee, K.W.; Jordan, H.; Curtis, L.A.; Kelly, R.F.; Kogan, V.; Schumacher, P.M.

1986-07-01

This report presents results of analyses of the enviromental releases of fission products (source terms) for severe accident scenarios in a pressurized water reactor with a subatmospheric containment design. The analyses were performed to support the Severe Accident Risk Reduction/Risk Rebaselining Program (SARRP) which is being undertaken for the US Nuclear Regulatory Commission by Sandia National Laboratories. In the SARRP program, risk estimates are being generated for a number of reference plant designs. the Surry plant has been used in this study as the reference plant for a subatmospheric design

Severe accident management program at Cofrentes Nuclear Power Plant

International Nuclear Information System (INIS)

Borondo, L.; Serrano, C.; Fiol, M.J.; Sanchez, A.

2000-01-01

Cofrentes Nuclear Power Plant (GE BWR/6) has implemented its specific Severe Accident Management Program within this year 2000. New organization and guides have been developed to successfully undertake the management of a severe accident. In particular, the Technical Support Center will count on a new ''Severe Accident Management Team'' (SAMT) which will be in charge of the Severe Accident Guides (SAG) when Control Room Crew reaches the Emergency Operation Procedures (EOP) step that requires containment flooding. Specific tools and training have also been developed to help the SAMT to mitigate the accident. (author)

NPP Krsko Severe Accident Management Guidelines Upgrade

International Nuclear Information System (INIS)

Mihalina, Mario; Spalj, Srdjan; Glaser, Bruno; Jalovec, Robi; Jankovic, Gordan

2014-01-01

Nuclear Power Plant Krsko (NEK) has decided to take steps for upgrade of safety measures to prevent severe accidents, and to improve the means to successfully mitigate their consequences. The content of the program for the NEK Safety Upgrade is consistent with the nuclear industry response to Fukushima accident, which revealed many new insights into severe accidents. Therefore, new strategies and usage of new systems and components should be integrated into current NEK Severe Accident Management Guidelines (SAMG's). SAMG's are developed to arrest the progression of a core damage accident and to limit the extent of resulting releases of fission products. NEK new SAMG's revision major changes are made due to: replacement of Electrical Recombiners by Passive Autocatalytic Recombiners (PARs) and the installation of Passive Containment Filtered Vent System (PCFV); to handle a fuel damage situation in Spent Fuel Pool (SFP) and to assess risk of core damage situation during shutdown operation. (authors)

Analysis and research status of severe core damage accidents

International Nuclear Information System (INIS)

1984-03-01

The Severe Core Damage Research and Analysis Task Force was established in Nuclear Safety Research Center, Tokai Research Establishment, JAERI, in May, 1982 to make a quantitative analysis on the issues related with the severe core damage accident and also to survey the present status of the research and provide the required research subjects on the severe core damage accident. This report summarizes the results of the works performed by the Task Force during last one and half years. The main subjects investigated are as follows; (1) Discussion on the purposes and necessities of severe core damage accident research, (2) proposal of phenomenological research subjects required in Japan, (3) analysis of severe core damage accidents and identification of risk dominant accident sequences, (4) investigation of significant physical phenomena in severe core damage accidents, and (5) survey of the research status. (author)

Severe accident analysis in a two-loop PWR nuclear power plant with the ASTEC code

International Nuclear Information System (INIS)

Sadek, Sinisa; Amizic, Milan; Grgic, Davor

2013-01-01

The ASTEC/V2.0 computer code was used to simulate a hypothetical severe accident sequence in the nuclear power plant Krsko, a 2-loop pressurized water reactor (PWR) plant. ASTEC is an integral code jointly developed by Institut de Radioprotection et de Surete Nucleaire (IRSN, France) and Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS, Germany) to assess nuclear power plant behaviour during a severe accident. The analysis was conducted in 2 steps. First, the steady state calculation was performed in order to confirm the applicability of the plant model and to obtain correct initial conditions for the accident analysis. The second step was the calculation of the station blackout accident with a leakage of the primary coolant through degraded reactor coolant pump seals, which was a small LOCA without makeup capability. Two scenarios were analyzed: one with and one without the auxiliary feedwater (AFW). The latter scenario, without the AFW, resulted in earlier core damage. In both cases, the accident ended with a core melt and a reactor pressure vessel failure with significant release of hydrogen. In addition, results of the ASTEC calculation were compared with results of the RELAP5/SCDAPSIM calculation for the same transient scenario. The results comparison showed a good agreement between predictions of those 2 codes. (orig.)

Airborne concentrations of radioactive materials in severe accidents

International Nuclear Information System (INIS)

Ross, D.F. Jr.; Denning, R.S.

1989-01-01

Radioactive materials would be released to the containment building of a commercial nuclear reactor during each of the stages of a severe accident. Results of analyses of two accident sequences are used to illustrate the magnitudes of these sources of radioactive materials, the resulting airborne mass concentrations, the characteristics of the airborne aerosols, the potential for vapor forms of radioactive materials, the effectiveness of engineered safety features in reducing airborne concentrations, and the release of radioactive materials to the environment. Ability to predict transport and deposition of radioactive materials is important to assessing the performance of containment safety features in severe accidents and in the development of accident management procedures to reduce the consequences of severe accidents

Factors associated with the severity of construction accidents: The case of South Australia

Directory of Open Access Journals (Sweden)

Jantanee Dumrak

2013-12-01

Full Text Available While the causes of accidents in the construction industry have been extensively studied, severity remains an understudied area. In order to provide more evidence for the currently limited number of empirical investigations on severity, this study analysed 24,764 construction accidents reported during 2002-11 in South Australia. A conceptual model developed through literature uses personal characteristics such as age, experience, gender and language. It also employs work-related factors such as size of organization, project size and location, mechanism of accident and body location of the injury. These were shown to discriminate why some accidents result in only a minor severity while others are fatal. Factors such as time of accident, day of the week and season were not strongly associated with accident severity. When the factors affecting severity of an accident are well understood, preventive measures could be developed specifically to those factors that are at high risk.

A computer code for analysis of severe accidents in LWRs

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

The ICARE2 computer code, developed and validated since 1988 at IPSN (nuclear safety and protection institute), calculates in a mechanistic way the physical and chemical phenomena involved in the core degradation process during possible severe accidents in LWR's. The coupling between ICARE2 and the best-estimate thermal-hydraulics code CATHARE2 was completed at IPSN and led to the release of a first ICARE/CATHARE V1 version in 1999, followed by 2 successive revisions in 2000 and 2001. This documents gathers all the contributions presented at the first international ICARE/CATHARE users'club seminar that took place in November 2001. This seminar was characterized by a high quality and variety of the presentations, showing an increase of reactor applications and user needs in this area (2D/3D aspects, reflooding, corium slumping into the lower head,...). 2 sessions were organized. The first one was dedicated to the applications of ICARE2 V3mod1 against small-scale experiments such as PHEBUS FPT2 and FPT3 tests, PHEBUS AIC, QUENCH experiments, NRU-FLHT-5 test, ACRR-MP1 and DC1 experiments, CORA-PWR tests, and PBF-SFD1.4 test. The second session involved ICARE/CATHARE V1mod1 reactor applications and users'guidelines. Among reactor applications we found: code applicability to high burn-up fuel rods, simulation of the TMI-2 transient, simulation of a PWR-900 high pressure severe accident sequence, and the simulation of a VVER-1000 large break LOCA scenario. (A.C.)

A computer code for analysis of severe accidents in LWRs

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

The ICARE2 computer code, developed and validated since 1988 at IPSN (nuclear safety and protection institute), calculates in a mechanistic way the physical and chemical phenomena involved in the core degradation process during possible severe accidents in LWR's. The coupling between ICARE2 and the best-estimate thermal-hydraulics code CATHARE2 was completed at IPSN and led to the release of a first ICARE/CATHARE V1 version in 1999, followed by 2 successive revisions in 2000 and 2001. This documents gathers all the contributions presented at the first international ICARE/CATHARE users'club seminar that took place in November 2001. This seminar was characterized by a high quality and variety of the presentations, showing an increase of reactor applications and user needs in this area (2D/3D aspects, reflooding, corium slumping into the lower head,...). 2 sessions were organized. The first one was dedicated to the applications of ICARE2 V3mod1 against small-scale experiments such as PHEBUS FPT2 and FPT3 tests, PHEBUS AIC, QUENCH experiments, NRU-FLHT-5 test, ACRR-MP1 and DC1 experiments, CORA-PWR tests, and PBF-SFD1.4 test. The second session involved ICARE/CATHARE V1mod1 reactor applications and users'guidelines. Among reactor applications we found: code applicability to high burn-up fuel rods, simulation of the TMI-2 transient, simulation of a PWR-900 high pressure severe accident sequence, and the simulation of a VVER-1000 large break LOCA scenario. (A.C.)

A computer code for analysis of severe accidents in LWRs

International Nuclear Information System (INIS)

2001-01-01

The ICARE2 computer code, developed and validated since 1988 at IPSN (nuclear safety and protection institute), calculates in a mechanistic way the physical and chemical phenomena involved in the core degradation process during possible severe accidents in LWR's. The coupling between ICARE2 and the best-estimate thermal-hydraulics code CATHARE2 was completed at IPSN and led to the release of a first ICARE/CATHARE V1 version in 1999, followed by 2 successive revisions in 2000 and 2001. This documents gathers all the contributions presented at the first international ICARE/CATHARE users'club seminar that took place in November 2001. This seminar was characterized by a high quality and variety of the presentations, showing an increase of reactor applications and user needs in this area (2D/3D aspects, reflooding, corium slumping into the lower head,...). 2 sessions were organized. The first one was dedicated to the applications of ICARE2 V3mod1 against small-scale experiments such as PHEBUS FPT2 and FPT3 tests, PHEBUS AIC, QUENCH experiments, NRU-FLHT-5 test, ACRR-MP1 and DC1 experiments, CORA-PWR tests, and PBF-SFD1.4 test. The second session involved ICARE/CATHARE V1mod1 reactor applications and users'guidelines. Among reactor applications we found: code applicability to high burn-up fuel rods, simulation of the TMI-2 transient, simulation of a PWR-900 high pressure severe accident sequence, and the simulation of a VVER-1000 large break LOCA scenario. (A.C.)

Recommended HPI [High Pressure Injection] rates for the TMI-2 analysis exercise (0 to 300 minutes)

International Nuclear Information System (INIS)

Anderson, J.L.

1987-09-01

An international analysis exercise has been organized to evaluate the ability of nuclear reactor severe accident computer codes to predict the TMI-2 accident sequence and core damage progression during the first 300 minutes of the accident. A required boundary condition for the analysis exercise is the High Pressure Injection or make-up rates into the primary system during the accident. Recommended injection rates for the first 300 minutes of the accident are presented. Recommendations for several sensitivity studies are also presented. 6 refs., 5 figs., 1 tab

Development of severe accident guidance module for the SATS simulator

International Nuclear Information System (INIS)

Kim, K.R.; Park, S.H.; Kim, D.H.; Song, Y.M.

2004-01-01

Recently KAERI has developed the severe accident management guidance to establish Korea standard severe accident management system. On the other hand the PC-based severe accident training simulator SATS has been developed, which uses MELCOR code as the simulation engine. SATS graphically displays and simulates the severe accidents with interactive user commands. The control capability of SATS could make severe accident training course more interesting and effective. In this paper we will describe the development and functions of the electrical hypertext guidance module HyperKAMG and the SATS-HyperKAMG linkage system for the severe accident management. (author)

Occupational Radiation Protection in Severe Accident Management. EG-SAM Interim Report

International Nuclear Information System (INIS)

2014-01-01

As an early response to the Fukushima NPP accident, the ISOE Bureau decided to focus on the following issues as an initial response of the joint program after having direct communications with the Japanese official participants in April 2011; - Management of high radiation area worker doses: It has been decided to make available the experience and information from the Chernobyl accident in terms of how emergency worker / responder doses were legally and practically managed, - Personal protective equipment for highly-contaminated areas: It was agreed to collect information about the types of personnel protective equipment and other equipment (e.g. air bottles, respirators, air-hoods or plastic suits, etc.), as well as high-radiation area worker dosimetry use (e.g. type, number and placement of dosimetry) for different types of emergency and high-radiation work situations. Detailed information was collected on dose criteria which are used for emergency workers/responders and their basis, dose management criteria for high dose/dose rate areas, protective equipment which is recommended for emergency workers / responders, recommended individual monitoring procedures, and any special requirement for assessment from the ISOE participating nuclear utilities and regulatory authorities and made available for Japanese utilities. With this positive response of the ISOE actors and interest in the situation in Fukushima, the Expert Group on Occupational Radiation Protection in Severe Accident Management (EG-SAM) was established by the ISOE Management Board in May 2011. The overall objective of the EG-SAM is to contribute to occupational exposure management (providing a view on management of high radiation area worker doses) within the Fukushima plant boundary with the ISOE participants and to develop a state-of-the- art ISOE report on best radiation protection management practices for proper radiation protection job coverage during severe accident initial response and recovery

Severe accident issue resolution -- definition and perspective

International Nuclear Information System (INIS)

Harper, F.T.

1995-01-01

The purpose of this discussion is to introduce the session on the Progress on the Resolution of Severe Accident Issues. There has been much work in the area of resolution of severe accident issues over the past few years. This work has been focused on those issues most important to risk as assessed by comprehensive studies such as NUREG-1150. In particular, issues associated with early containment failure have been analyzed. These efforts to resolve issues have been hampered by the fact that open-quotes issue resolutionclose quotes has not always been well defined. The term open-quotes issue resolutionclose quotes conjures tip different images for the regulator, the accident analyst, the physicist, and the probabalist. In fact it is common to have as many different images of issue resolution as there are people in the room. This issue is complicated by the fact that the uncertainty in severe accident issues is enormous. (When convolved, the quantitative uncertainty in an integrated analysis due to severe accident issues can span several orders of magnitude.) In this summary, hierarchy is presented in an attempt to add some perspective to the resolution of issues in the face of large uncertainties. Recommendations are also made for analysts communicating in the area of issue resolution

Development of ultrasonic high temperature system for severe accidents research

International Nuclear Information System (INIS)

Koo, Kil Mo; Kang, Kyung Ho; Kim, Young Ro and others

2000-07-01

The aims of this study are to find a gap formation between corium melt and the reactor lower head vessel, to verify the principle of the gap formation and to analyze the effect of the gap formation on the thermal behavior of corium melt and the lower plenum. This report aims at suggesting development of a new high temperature measuring system using an ultrasonic method which overcomes the limitations of the present thermocouple method used for severe accident experiments. Also, this report describes the design and manufacturing method of the ultrasonic system. At that time, the sensor element is fabricated to a reflective element using 1mm diameter and 50 mm and 80 mm long tungsten alloy wires. This temperature measuring system is intended to measure up to 2800 deg C

Outline of the Desktop Severe Accident Graphic Simulator Module for OPR-1000

International Nuclear Information System (INIS)

Park, S. Y.; Ahn, K. I.

2015-01-01

This paper introduce the desktop severe accident graphic simulator module (VMAAP) which is a window-based severe accident simulator using MAAP as its engine. The VMAAP is one of the submodules in SAMEX system (Severe Accident Management Support Expert System) which is a decision support system for use in a severe accident management following an incident at a nuclear power plant. The SAMEX system consists of four major modules as sub-systems: (a) Severe accident risk data base module (SARDB): stores the data of integrated severe accident analysis code results like MAAP and MELCOR for hundreds of high frequency scenarios for the reference plant; (b) Risk-informed severe accident risk data base management module (RI-SARD): provides a platform to identify the initiating event, determine plant status and equipment availability, diagnoses the status of the reactor core, reactor vessel and containment building, and predicts the plant behaviors; (c) Severe accident management simulator module (VMAAP): runs the MAAP4 code with user friendly graphic interface for input deck and output display; (d) On-line severe accident management guidance module (On-line SAMG); provides available accident management strategies with an electronic format. The role of VMAAP in SAMEX can be described as followings. SARDB contains the most of high frequency scenarios based on a level 2 probabilistic safety analysis. Therefore, there is good chance that a real accident sequence is similar to one of the data base cases. In such a case, RI-SARD can predict an accident progression by a scenario-base or symptom-base search depends on the available plant parameter information. Nevertheless, there still may be deviations or variations between the actual scenario and the data base scenario. The deviations can be decreased by using a real-time graphic accident simulator, VMAAP.. VMAAP is a MAAP4-based severe accident simulation model for OPR-1000 plant. It can simulate spectrum of physical processes

Outline of the Desktop Severe Accident Graphic Simulator Module for OPR-1000

Energy Technology Data Exchange (ETDEWEB)

Park, S. Y.; Ahn, K. I. [KAERI, Daejeon (Korea, Republic of)

2015-05-15

This paper introduce the desktop severe accident graphic simulator module (VMAAP) which is a window-based severe accident simulator using MAAP as its engine. The VMAAP is one of the submodules in SAMEX system (Severe Accident Management Support Expert System) which is a decision support system for use in a severe accident management following an incident at a nuclear power plant. The SAMEX system consists of four major modules as sub-systems: (a) Severe accident risk data base module (SARDB): stores the data of integrated severe accident analysis code results like MAAP and MELCOR for hundreds of high frequency scenarios for the reference plant; (b) Risk-informed severe accident risk data base management module (RI-SARD): provides a platform to identify the initiating event, determine plant status and equipment availability, diagnoses the status of the reactor core, reactor vessel and containment building, and predicts the plant behaviors; (c) Severe accident management simulator module (VMAAP): runs the MAAP4 code with user friendly graphic interface for input deck and output display; (d) On-line severe accident management guidance module (On-line SAMG); provides available accident management strategies with an electronic format. The role of VMAAP in SAMEX can be described as followings. SARDB contains the most of high frequency scenarios based on a level 2 probabilistic safety analysis. Therefore, there is good chance that a real accident sequence is similar to one of the data base cases. In such a case, RI-SARD can predict an accident progression by a scenario-base or symptom-base search depends on the available plant parameter information. Nevertheless, there still may be deviations or variations between the actual scenario and the data base scenario. The deviations can be decreased by using a real-time graphic accident simulator, VMAAP.. VMAAP is a MAAP4-based severe accident simulation model for OPR-1000 plant. It can simulate spectrum of physical processes

Interaction of radionuclides in severe accident conditions

International Nuclear Information System (INIS)

Nagrale, Dhanesh B.; Bera, Subrata; Deo, Anuj Kumar; Paul, U.K.; Prasad, M.; Gaikwad, A.J.

2015-01-01

Nuclear power plants are designed with inherent engineering safety systems and associated operational procedures that provide an in-depth defence against accidents. Radionuclides such as Iodine, Cesium, Tellurium, Barium, Strontium, Rubidium, Molybdenum and many others may get released during a severe accident. Among these, Iodine, one of the fission products, behaviour is significant for the analysis of severe accident consequences because iodine is a chemically more active to the potential components released to the environment. During severe accident, Iodine is released and transported in aqueous, organic and inorganic forms. Iodine release from fuel, iodine transport in primary coolant system, containment, and reaction with control rods are some of the important phases in a severe accident scenario. The behaviour of iodine is governed by aerosol physics, depletion mechanisms gravitational settling, diffusiophoresis and thermophoresis. The presence of gaseous organic compounds and oxidizing compounds on iodine, reactions of aerosol iodine with boron and formation of cesium iodide which results in more volatile iodine release in containment play significant roles. Water radiolysis products due to presence of dissolved impurities, chloride ions, organic impurities should be considered while calculating iodine release. Containment filtered venting system (CFVS) consists of venturi scrubber and a scrubber tank which is dosed with NaOH and NaS_2O_3 in water where iodine will react with the chemicals and convert into NaI and Na_2SO_4. This paper elaborates the issues with respect to interaction of radionuclides and its consideration in modeling of severe accident. (author)

Calculation of spent fuel pool severe accident with MELCOR

International Nuclear Information System (INIS)

Deng Jian; Xiang Qing'an; Zhou Kefeng

2014-01-01

A calculation model was established for spent fuel pool (SFP) using MELCOR code to study the severe accident phenomena caused by the long term station black-out (SBO), including spent fuel heatup, zirconium cladding oxidation, and the injection into SFP to mitigate the severe accident. The results show that the severe accident progression is slow and relates directly with the initial water level in SFP. It is illustrated that the injection into SFP is one of the best mitigated measures for the SFP severe accident. (authors)

Early results from an experimental program to determine the behavior of containment piping penetration bellows subjected to severe accident conditions

International Nuclear Information System (INIS)

Lambert, L.D.; Parks, M.B.

1994-01-01

Containment piping penetration bellows are an integral part of the pressure boundary in steel containments in the United States (US). Their purpose is to minimize loading on the containment shell caused by differential movement between the piping and the containment. This differential movement is typically caused by thermal gradients generated during startup and shutdown of the reactor, but can be caused by earthquake, a loss-of-coolant accident (LOCA), or ''severe'' accidents. In the event of a severe accident, the bellows would be subjected to pressure, temperature, and deflection well beyond the design basis. Most bellows are installed such that they would be subjected to elevated internal pressure, elevated temperature, axial compression, and lateral deflection during a severe accident. A few bellows would be subjected to external pressure and axial elongation, as well as elevated temperature and lateral deflection. The purpose of this experimental program is to examine the potential for leakage of containment bellows during a severe accident. The test series subjects bellows to various levels and combinations of internal pressure, elevated temperature, axial compression or elongation, and lateral deformation. The experiments are being conducted in two parts. For Part 1, all bellows specimens are tested in ''like-new'' condition, without regard for the possible degrading effect of corrosion that has been observed in some containment piping bellows in the US Part I testing, which included 13 bellows tests, has been completed. The second part of the experimental program, in which bellows are subjected to simulated corrosive environments prior to testing, has just just begun. The Part I experiments have shown that bellows in ''like-new'' condition can withstand elevated temperatures and pressures along with large deformations before leaking. In most cases, the like-new bellows were fully compressed without developing any leakage

Strategy-oriented display concept to assist severe accident management

International Nuclear Information System (INIS)

Jeong, Kwangsub; Ha, Jaejoo

2000-01-01

The Critical Function Monitoring System (CFMS) is a typical Safety Parameter Display System (SPDS) to assist the operation of Korean Standard Nuclear Power Plants during normal and emergency operation, and SPDS for severe accident is being developed in Korea. When the existing CFMS is used under a severe accident situation, some problems are expected from: (1) different design basis, i.e. prevention of core melt vs. protection of radiation release to environment, (2) different parameters for decision-making, and (3) different domain and depth of information to restore the plant. To resolve the above problems, a concept, 'Strategy-Oriented Information Display' concept, for displaying information for severe accident management is developed in this paper. Whereas the existing SPDS structure is based on the critical safety function, the developed concept is based on the severe accident management strategy. The display for each strategy includes the plant parameters to check the status of plant and component with the logical or graphical views necessary for executing the strategy. As the application of the proposed concept, KAERI is developing a display system, the prototype severe accident SPDS, Severe Accident Management Display System (SAMDIS), to assist plant personnel for executing Korean Severe Accident Management Guidelines. CFMS is developed for a general display suitable to all situations with various displays. On the contrary, SAMDIS provides all the relevant information on one screen based on the proposed concept. The SAMDIS screen shows more extensive area than CFMS and thus plant personnel can recognize the overall plant status at a glance. This concept is quite effective when used with severe accident management guidelines because of the relatively macroscopic characteristics of a severe accident management strategy. (author)

ADAM: An Accident Diagnostic,Analysis and Management System - Applications to Severe Accident Simulation and Management

International Nuclear Information System (INIS)

Zavisca, M.J.; Khatib-Rahbar, M.; Esmaili, H.; Schulz, R.

2002-01-01

The Accident Diagnostic, Analysis and Management (ADAM) computer code has been developed as a tool for on-line applications to accident diagnostics, simulation, management and training. ADAM's severe accident simulation capabilities incorporate a balance of mechanistic, phenomenologically based models with simple parametric approaches for elements including (but not limited to) thermal hydraulics; heat transfer; fuel heatup, meltdown, and relocation; fission product release and transport; combustible gas generation and combustion; and core-concrete interaction. The overall model is defined by a relatively coarse spatial nodalization of the reactor coolant and containment systems and is advanced explicitly in time. The result is to enable much faster than real time (i.e., 100 to 1000 times faster than real time on a personal computer) applications to on-line investigations and/or accident management training. Other features of the simulation module include provision for activation of water injection, including the Engineered Safety Features, as well as other mechanisms for the assessment of accident management and recovery strategies and the evaluation of PSA success criteria. The accident diagnostics module of ADAM uses on-line access to selected plant parameters (as measured by plant sensors) to compute the thermodynamic state of the plant, and to predict various margins to safety (e.g., times to pressure vessel saturation and steam generator dryout). Rule-based logic is employed to classify the measured data as belonging to one of a number of likely scenarios based on symptoms, and a number of 'alarms' are generated to signal the state of the reactor and containment. This paper will address the features and limitations of ADAM with particular focus on accident simulation and management. (authors)

TMI-2 - A Case Study for PWR Instrumentation Performance during a Severe Accident

Energy Technology Data Exchange (ETDEWEB)

Joy L. Rempe; Darrell L. Knudson

2014-05-01

The accident at the Three Mile Island Unit 2 (TMI-2) reactor provided a unique opportunity to evaluate sensors exposed to severe accident conditions. Conditions associated with the release of coolant and the hydrogen burn that occurred during this accident exposed instrumentation to harsh conditions, including direct radiation, radioactive contamination, and high humidity with elevated temperatures and pressures. As part of a program initiated in 2012 by the Department of Energy Office of Nuclear Energy (DOE-NE), a review was completed to gain insights from prior TMI-2 sensor survivability and data qualification efforts. This new effort focussed upon a set of sensors that provided critical data to TMI-2 operators for assessing the condition of the plant and the effects of mitigating actions taken by these operators. In addition, the effort considered sensors providing data required for subsequent accident simulations. Over 100 references related to instrumentation performance and post-accident evaluations of TMI-2 sensors and measurements were reviewed. Insights gained from this review are summarized within this report. For each sensor, a description is provided with the measured data and conclusions related to the sensor’s survivability, and the basis for conclusions about its survivability. As noted within this document, several techniques were invoked in the TMI-2 post-accident evaluation program to assess sensor status, including comparisons with data from other sensors, analytical calculations, laboratory testing, and comparisons with sensors subjected to similar conditions in large-scale integral tests and with sensors that were similar in design but more easily removed from the TMI-2 plant for evaluations. Conclusions from this review provide important insights related to sensor survivability and enhancement options for improving sensor performance. In addition, this document provides recommendations related to the sensor survivability and data evaluation

TMI-2 - A Case Study for PWR Instrumentation Performance during a Severe Accident

Energy Technology Data Exchange (ETDEWEB)

Joy L. Rempe; Darrell L. Knudson

2013-03-01

The accident at the Three Mile Island Unit 2 (TMI-2) reactor provided a unique opportunity to evaluate sensors exposed to severe accident conditions. Conditions associated with the release of coolant and the hydrogen burn that occurred during this accident exposed instrumentation to harsh conditions, including direct radiation, radioactive contamination, and high humidity with elevated temperatures and pressures. As part of a program initiated in 2012 by the Department of Energy Office of Nuclear Energy (DOE-NE), a review was completed to gain insights from prior TMI-2 sensor survivability and data qualification efforts. This new effort focussed upon a set of sensors that provided critical data to TMI-2 operators for assessing the condition of the plant and the effects of mitigating actions taken by these operators. In addition, the effort considered sensors providing data required for subsequent accident simulations. Over 100 references related to instrumentation performance and post-accident evaluations of TMI-2 sensors and measurements were reviewed. Insights gained from this review are summarized within this report. For each sensor, a description is provided with the measured data and conclusions related to the sensor’s survivability, and the basis for conclusions about its survivability. As noted within this document, several techniques were invoked in the TMI-2 post-accident evaluation program to assess sensor status, including comparisons with data from other sensors, analytical calculations, laboratory testing, and comparisons with sensors subjected to similar conditions in large-scale integral tests and with sensors that were similar in design but more easily removed from the TMI-2 plant for evaluations. Conclusions from this review provide important insights related to sensor survivability and enhancement options for improving sensor performance. In addition, this document provides recommendations related to the sensor survivability and data evaluation

Simulation and Damage Analysis of an Accidental Jet Fire in a High-Pressure Compressed Pump Shelter

OpenAIRE

Jang, Chang Bong; Choi, Sang-Won

2016-01-01

Background: As one of the most frequently occurring accidents in a chemical plant, a fire accident may occur at any place where transfer or handling of combustible materials is routinely performed. Methods: In particular, a jet fire incident in a chemical plant operated under high pressure may bring severe damage. To review this event numerically, Computational Fluid Dynamics methodology was used to simulate a jet fire at a pipe of a compressor under high pressure. Results: For jet fire...

ACR-1000 design provisions for severe accidents

International Nuclear Information System (INIS)

Popov, N.K.; Santamaura, P.; Shapiro, H.; Snell, V.G.

2006-01-01

Atomic Energy of Canada Limited (AECL) developed the Advanced CANDU Reactor-700 (ACR-700) as an evolutionary advancement of the current CANDU 6 reactor. As a further advancement of the ACR design, AECL is currently developing the ACR-1000 for the Canadian and international market. The ACR-1000 is aimed at producing electrical power for a capital cost and a unit-energy cost significantly less than that of the current generation of operating nuclear plants, while achieving enhanced safety features, shorter construction schedule, high plant capacity factor, improved operations and maintenance, and increased operating life. The reference ACR-1000 plant design is based on an integrated two-unit plant, using enriched fuel and light-water coolant, with each unit having a nominal gross output of about 1200 MWe. The ACR-1000 design meets Canadian regulatory requirements and follows established international practice with respect to severe accident prevention and mitigation. This paper presents the ACR-1000 features that are designed to mitigate limited core damage and severe core damage states, including core retention within vessel, core damage termination, and containment integrity maintenance. While maintaining existing structures of CANDU reactors that provide inherent prevention and retention of core debris, the ACR-1000 design includes additional features for prevention and mitigation of severe accidents. Core retention within vessel in CANDU-type reactors includes both retention within fuel channels, and retention within the calandria vessel. The ACR-1000 calandria vessel design permits for passive rejection of decay heat from the moderator to the shield water. Also, the calandria vessel is designed for debris retention by minimizing penetrations at the bottom periphery and by accommodating thermal and weight loads of the core debris. The ACR-1000 containment is required to withstand external events such as earthquakes, tornados, floods and aircraft crashes

Consideration of severe accidents in design of advanced WWER reactors

International Nuclear Information System (INIS)

Fedorov, V.G.; Rogov, M.F.; Podshibyakin, A.K.; Fil, N.S.; Volkov, B.E.; Semishkin, V.P.

1998-01-01

Severe accident related requirements formulated in General Regulations for Nuclear Power Plant Safety (OPB-88), in Nuclear Safety Regulations for Nuclear Power Stations' Reactor Plants (PBYa RU AS-89) and in other NPP nuclear and radiation guides of the Russian Gosatomnadzor are analyzed. In accordance with these guides analyses of beyond design basis accidents should be performed in the reactor plant design. Categorization of beyond design basis accidents leading to severe accidents should be made on occurrence probability and severity of consequences. Engineered features and measures intended for severe accident management should be provided in reactor plant design. Requirements for severe accident analyses and for development of measures for severe accident management are determined. Design philosophy and proposed engineered measures for mitigation of severe accidents and decrease of radiation releases are demonstrated using examples of large, WWER-1000 (V-392), and medium size WWER-640 (V-407) reactor plant designs. Mitigation of severe accidents and decrease of radiation releases are supposed to be conducted on basis of consistent realization of the defense in depth concept relating to application of a system of barriers on the path of spreading of ionizing radiation and radioactive materials to the environment and a set of engineered measures protecting these barriers and retaining their effectiveness. Status of fulfilled by OKB Gidropress and other Russian organizations experimental and analytical investigations of severe accident phenomena supporting design decisions and severe accident management procedures is described. Status of the works on retention of core melt inside the WWER-640 reactor vessel is also characterized

Response Analysis on Electrical Pulses under Severe Nuclear Accident Temperature Conditions Using an Abnormal Signal Simulation Analysis Module

Directory of Open Access Journals (Sweden)

Kil-Mo Koo

2012-01-01

Full Text Available Unlike design basis accidents, some inherent uncertainties of the reliability of instrumentations are expected while subjected to harsh environments (e.g., high temperature and pressure, high humidity, and high radioactivity occurring in severe nuclear accident conditions. Even under such conditions, an electrical signal should be within its expected range so that some mitigating actions can be taken based on the signal in the control room. For example, an industrial process control standard requires that the normal signal level for pressure, flow, and resistance temperature detector sensors be in the range of 4~20 mA for most instruments. Whereas, in the case that an abnormal signal is expected from an instrument, such a signal should be refined through a signal validation process so that the refined signal could be available in the control room. For some abnormal signals expected under severe accident conditions, to date, diagnostics and response analysis have been evaluated with an equivalent circuit model of real instruments, which is regarded as the best method. The main objective of this paper is to introduce a program designed to implement a diagnostic and response analysis for equivalent circuit modeling. The program links signal analysis tool code to abnormal signal simulation engine code not only as a one body order system, but also as a part of functions of a PC-based ASSA (abnormal signal simulation analysis module developed to obtain a varying range of the R-C circuit elements in high temperature conditions. As a result, a special function for abnormal pulse signal patterns can be obtained through the program, which in turn makes it possible to analyze the abnormal output pulse signals through a response characteristic of a 4~20 mA circuit model and a range of the elements changing with temperature under an accident condition.

New Solutions For Increasing Environmental Protection During Severe Accidents At Nuclear Power Plants

International Nuclear Information System (INIS)

Kulyukhin, Sergei A.; Mikheev, Nikolai B.; Falkovskii, Leo N.; Reshetov, Leo A.; Zvetkova, Marianna Ya.; Yagodkin, Ivan V.; Osipov, Viktor P.; Skvortsov, Sergei S.; Berkovich, Viktor M.; Taranov, Gennadii S.; Grigor'ev, Mikhail M.; Meshkov, Vladimir M.; Noskov, Andrei A.; Mitrofanov, Mikhail I.

2008-01-01

This paper reports new solutions for increasing environmental protection during severe accidents at NPPs. For NPPs with two protective shells and pressure release system such as WWER-1000 we suggest a new comprehensive, passive-mode environmental protection system of decontamination of the radioactive air-steam mixture from the containment and the inter-containment area, which includes the 'wet' stage (scrubbers, etc.), the 'dry' stage (sorption module), and also an ejector, which in a passive mode is capable of solving the multi-purpose task of decontamination of the air-steam mixture. For Russian WWER-440/230 NPPs we suggest three protection levels: 1) a jet-vortex condenser; 2) the spray system; 3) a sorption module. For modern designs of new generation NPPs, which do not provide for pressure release systems, we proposed a new passive filtering system together with the passive heat-removal system, which can be used during severe accidents in case all power supply units become unavailable. (authors)

New Solutions For Increasing Environmental Protection During Severe Accidents At Nuclear Power Plants

Energy Technology Data Exchange (ETDEWEB)

Kulyukhin, Sergei A.; Mikheev, Nikolai B. [Institute of Physical Chemistry and Electrochemistry, Russian Academy of Sciences, Moscow (Russian Federation); Falkovskii, Leo N.; Reshetov, Leo A.; Zvetkova, Marianna Ya. [All-Russian Research Institute of Atomic Machine-Building, Moscow, Russia (Russian Federation); Yagodkin, Ivan V.; Osipov, Viktor P.; Skvortsov, Sergei S. [Institute of Physics and Power Engineering, Obninsk (Russian Federation); Berkovich, Viktor M.; Taranov, Gennadii S.; Grigor' ev, Mikhail M. [Institute ' Atomenergoproekt' , Moscow (Russian Federation); Meshkov, Vladimir M.; Noskov, Andrei A.; Mitrofanov, Mikhail I. [ROSENERGOATOM Concern, Moscow (Russian Federation)

2008-07-01

This paper reports new solutions for increasing environmental protection during severe accidents at NPPs. For NPPs with two protective shells and pressure release system such as WWER-1000 we suggest a new comprehensive, passive-mode environmental protection system of decontamination of the radioactive air-steam mixture from the containment and the inter-containment area, which includes the 'wet' stage (scrubbers, etc.), the 'dry' stage (sorption module), and also an ejector, which in a passive mode is capable of solving the multi-purpose task of decontamination of the air-steam mixture. For Russian WWER-440/230 NPPs we suggest three protection levels: 1) a jet-vortex condenser; 2) the spray system; 3) a sorption module. For modern designs of new generation NPPs, which do not provide for pressure release systems, we proposed a new passive filtering system together with the passive heat-removal system, which can be used during severe accidents in case all power supply units become unavailable. (authors)

Root causes and impacts of severe accidents at large nuclear power plants.

Science.gov (United States)

Högberg, Lars

2013-04-01

The root causes and impacts of three severe accidents at large civilian nuclear power plants are reviewed: the Three Mile Island accident in 1979, the Chernobyl accident in 1986, and the Fukushima Daiichi accident in 2011. Impacts include health effects, evacuation of contaminated areas as well as cost estimates and impacts on energy policies and nuclear safety work in various countries. It is concluded that essential objectives for reactor safety work must be: (1) to prevent accidents from developing into severe core damage, even if they are initiated by very unlikely natural or man-made events, and, recognizing that accidents with severe core damage may nevertheless occur; (2) to prevent large-scale and long-lived ground contamination by limiting releases of radioactive nuclides such as cesium to less than about 100 TBq. To achieve these objectives the importance of maintaining high global standards of safety management and safety culture cannot be emphasized enough. All three severe accidents discussed in this paper had their root causes in system deficiencies indicative of poor safety management and poor safety culture in both the nuclear industry and government authorities.

Root Causes and Impacts of Severe Accidents at Large Nuclear Power Plants

International Nuclear Information System (INIS)

Hoegberg, Lars

2013-01-01

The root causes and impacts of three severe accidents at large civilian nuclear power plants are reviewed: the Three Mile Island accident in 1979, the Chernobyl accident in 1986, and the Fukushima Daiichi accident in 2011. Impacts include health effects, evacuation of contaminated areas as well as cost estimates and impacts on energy policies and nuclear safety work in various countries. It is concluded that essential objectives for reactor safety work must be: (1) to prevent accidents from developing into severe core damage, even if they are initiated by very unlikely natural or man-made events, and, recognizing that accidents with severe core damage may nevertheless occur; (2) to prevent large-scale and long lived ground contamination by limiting releases of radioactive nuclides such as cesium to less than about 100 TBq. To achieve these objectives the importance of maintaining high global standards of safety management and safety culture cannot be emphasized enough. All three severe accidents discussed in this paper had their root causes in system deficiencies indicative of poor safety management and poor safety culture in both the nuclear industry and government authorities

Root Causes and Impacts of Severe Accidents at Large Nuclear Power Plants

Energy Technology Data Exchange (ETDEWEB)

Hoegberg, Lars

2013-04-15

The root causes and impacts of three severe accidents at large civilian nuclear power plants are reviewed: the Three Mile Island accident in 1979, the Chernobyl accident in 1986, and the Fukushima Daiichi accident in 2011. Impacts include health effects, evacuation of contaminated areas as well as cost estimates and impacts on energy policies and nuclear safety work in various countries. It is concluded that essential objectives for reactor safety work must be: (1) to prevent accidents from developing into severe core damage, even if they are initiated by very unlikely natural or man-made events, and, recognizing that accidents with severe core damage may nevertheless occur; (2) to prevent large-scale and long lived ground contamination by limiting releases of radioactive nuclides such as cesium to less than about 100 TBq. To achieve these objectives the importance of maintaining high global standards of safety management and safety culture cannot be emphasized enough. All three severe accidents discussed in this paper had their root causes in system deficiencies indicative of poor safety management and poor safety culture in both the nuclear industry and government authorities.

Helicopter type and accident severity in Helicopter Emergency Medical Services missions.

Science.gov (United States)

Hinkelbein, Jochen; Schwalbe, Mandy; Wetsch, Wolfgang A; Spelten, Oliver; Neuhaus, Christopher

2011-12-01

Whereas accident rates and fatal accident rates for Helicopter Emergency Medical Services (HEMS) were investigated sufficiently, resulting consequences for the occupants remain largely unknown. The present study aimed to classify HEMS accidents in Germany to prognosticate accident severity with regard to the helicopter model used. German HEMS accidents (1 Sept. 1970-31 Dec. 2009) were gathered as previously reported. Accidents were categorized in relation to the most severe injury, i.e., (1) no; (2) slight; (3) severe; and (4) fatal injuries. Only helicopter models with at least five accidents were analyzed to retrieve representative data. Prognostication was estimated by the relative percentage of each injury type compared to the total number of accidents. The model BO105 was most often involved in accidents (38 of 99), followed by BK117 and UH-1D. OfN = 99 accidents analyzed, N = 63 were without any injuries (63.6%), N = 8 resulted in minor injuries of the occupants (8.1%), and N = 9 in major injuries (9.1%). Additionally, N = 19 fatal accidents (19.2%) were registered. EC135 and BK1 17 had the highest incidence of uninjured occupants (100% vs. 88.2%) and the lowest percentage of fatal injuries (0% vs. 5.9%; all P > 0.05). Most fatal accidents occurred with the models UH-1D, Bell 212, and Bell 412. Use of the helicopter models EC135 and BK117 resulted in a high percentage of uninjured occupants. In contrast, the fatality rate was highest for the models Bell UH-I D, Bell 222, and Bell 412. Data from the present study allow for estimating accident risk in HEMS missions and prognosticating resulting fatalities, respectively.

Statistical modelling of the frequency and severity of road accidents

DEFF Research Database (Denmark)

Janstrup, Kira Hyldekær

-reporting. The problem of under-reporting is not unique for traffic accidents as severe under-reporting is a challenge in many other fields of incident reporting. In other incidents fields with intended or unintended harm, research has investigated the behavioural reasons for why people choose to report an incident......Under-reporting of traffic accidents is a well-discussed subject in traffic safety and it is well-known that the degree of under-reporting of traffic accidents is quite high in many countries. Nevertheless, very little literature has been made to investigate what causes the high degree of under...... on the service quality within the police none have looked at the service quality specific for the handling of traffic accidents.The objective of this Ph.D. thesis is to investigate the extent of under-reporting of traffic accidents in Denmark and trace the under-reporting systematically. As something new...

Estimation of cost per severe accident for improvement of accident protection and consequence mitigation strategies

International Nuclear Information System (INIS)

Silva, Kampanart; Ishiwatari, Yuki; Takahara, Shogo

2013-01-01

To assess the complex situations regarding the severe accidents such as what observed in Fukushima Accident, not only radiation protection aspects but also relevant aspects: health, environmental, economic and societal aspects; must be all included into the consequence assessment. In this study, the authors introduce the “cost per severe accident” as an index to analyze the consequences of severe accidents comprehensively. The cost per severe accident consists of various costs and consequences converted into monetary values. For the purpose of improvement of the accident protection and consequence mitigation strategies, the costs needed to introduce the protective actions, and health and psychological consequences are included in the present study. The evaluations of these costs and consequences were made based on the systematic consequence analysis using level 2 and 3 probabilistic safety assessment (PSA) codes. The accident sequences used in this analysis were taken from the results of level 2 seismic PSA of a virtual 1,100 MWe BWR-5. The doses to the public and the number of people affected were calculated using the level 3 PSA code OSCAAR of Japan Atomic Energy Agency (JAEA). The calculations have been made for 248 meteorological sequences, and the outputs are given as expectation values for various meteorological conditions. Using these outputs, the cost per severe accident is calculated based on the open documents on the Fukushima Accident regarding the cost of protective actions and compensations for psychological harms. Finally, optimized accident protection and consequence mitigation strategies are recommended taking into account the various aspects comprehensively using the cost per severe accident. The authors must emphasize that the aim is not to estimate the accident cost itself but to extend the scope of “risk-informed decision making” for continuous safety improvements of nuclear energy. (author)

New system technologies implemented at Kozloduy 3 and 4 (WWER 440-230) for containment leakage and H2 control in severe accident situations - Design, qualification, installation, commissioning

International Nuclear Information System (INIS)

Feuerbach, R.; Eckardt, B.; Kastner, B.

2005-01-01

In order to reduce the residual risk associated with hypothetical severe nuclear accidents, systems and components for filtered containment venting and H 2 reduction were developed. During severe accident scenarios large quantities of hydrogen and radioactive material may be released into the containment atmosphere within a short period of time. In the event of internal over pressurization due to hypothetical severe accident sequences a pressure barrier system has to be created to confine the activity in the containment. Unavoidable releases of activity to the environment have to be minimized to a great extent as possible. Research into the hypothetical event of core melt accidents has continued and new accident mitigation technologies have been developed. Decisions have been taken to implement these new mitigation measures in operating nuclear power plants to mitigate severe accidents consequences. In order to prevent loss of containment integrity as a result of over pressurization, nuclear power plants in the Federal Republic of Germany as well as in most other European countries have been or will be back-fitted with systems for filtered venting of the containment atmosphere and systems for H 2 -control. Similar technologies for containment venting system and H 2 control have been now implemented in the first WWER 440-230 units of Kozloduy 3 and 4. Following OECD recommendations sever accident situations were analyzed and a design of countermeasures have been performed. Main goal of the developed countermeasures was to overcome the WWER 440-230 containment design specifics like, leakage rate behavior, limited available containment volume combined with the feature of high availability of electrical supply at multiple plant sites. Further more the design of counter measures considers the common use for Kozloduy unit 3 and 4. The analysis of postulated severs accident situation - without countermeasures - showed significant increase of H 2 /O 2 concentration in the

Parametric study of recriticality in a boiling water reactor severe accident

International Nuclear Information System (INIS)

Shamoun, B.I.; Witt, R.J.

1994-01-01

Recriticality is possible in a severe accident if unborated or low boron concentration water is added to a damaged core after control rod melting but before fuel melting. Recriticality in a severe accident in a boiling water reactor was parametrically investigated using the TWODANT code. Eigenvalue calculations for a unit central fuel cell with reflective boundary conditions were performed by solving the two-dimensional multigroup steady-state Boltzman transport equation using TWODANT. Two sets of calculations were performed in this work. The first set of calculations was carried out under three types of normal operating conditions to provide reference values for the accident calculations: (a) cold rodded condition, (b) cold unrodded condition, and (c) hot full-power condition. The eigenvalues at these conditions were found to be 1.055, 1.208, and 1.098, respectively. The second set of calculations was carried out after the melting of the control element and during the reflood phase, under the following reflood conditions: (a) reflood with unborated water and (b) reflood with borated water. For the reflood case with unborated water, five values of void fractions were considered (100, 60, 40, 20, and 0%). Decreasing void fractions represent greater refill levels during the reflood process. The system pressure was taken to be 7 MPa, while the moderator temperature was set to 560 K. Plotting the eigenvalue compared with the fraction of control materials lost indicates recriticality is only possible if nearly 100% of the control material is lost from the core. Eigenvalue calculations were repeated for short- and long-term recovery conditions of the reflood phase corresponding to maximum moderator density at 4 MPa pressure and 525 K moderator temperature and for 1 MPa pressure and 325 K moderator temperature, respectively. Recriticality was again observed to be a concern only after losing 95% ore more of control materials from the unit cell

Assessment of PASS Effectiveness under Severe Accidents in Nuclear Power Plants

International Nuclear Information System (INIS)

Choi, Yu Jung; Lee, Sung Bok; Kim, Hyeong Taek; Lee, Jin Yong

2008-01-01

Following the accident at Three Mile Island Unit 2 (TMI-2) on March 28, 1979, the USNRC formed a lessons-learned Task Force to identify and evaluate safety concerns originating with the TMI-2 accident. NUREG-0578 documented the results of the task force effort. One of the recommendations of the task force was for licensees to upgrade the capability to obtain samples from the reactor coolant system and containment atmosphere under high radioactivity conditions and to provide the capability for chemical and spectral analyses of high-level samples on site. NUREG-0737 contained the details of the TMI recommendations that were to be implemented by the licensees. Additional criteria for post accident sampling system(PASS) were issued by Regulatory Guide 1.97. As the results, PASS has been installed on nuclear power plants(NPPs) in Korea as well as United States. However, significant improvements have been achieved since the TMI-2 accident in the areas of understanding risks associated with nuclear plant operations and developing better strategies for managing the response to potential severe accidents at NPPs. Thus, the requirements for PASS have been re-evaluated in some reports. According to the reports, the samples and measurements from PASS do not contribute significantly to emergency management response to severe accidents due to the long analyzing time, 3 hours. Hence, this paper focused on the development of the quantitative analysis methodology to analyze the sequence of the severe accident in Yonggwang nuclear power plants (YGN) and presented the results of the analysis according to the developed methodology

The technical requirements concerning severe accident management in nuclear power plants

International Nuclear Information System (INIS)

Okamoto, Koji; Sugiyama, Tomoyuki; Kamata, Shinya

2014-01-01

The Great East Japan Earthquake with a magnitude of 9.0 (The 2011 off the Pacific coast of Tohoku Earthquake) occurred on March 11, 2011, and the beyond design-basis tsunami descended on the Fukushima Daiichi Nuclear Power Plant by the earthquake. Eventually, the core cooling systems of the units 1, 2 and 3 could not operate stably, they all suffered severe accident, and hydrogen explosions were triggered in the reactor buildings of units 1, 3 and 4. In the light of these circumstances, Atomic Energy Society of Japan (AESJ) decided to establish a standard that consolidates the concept of maintaining and improving severe accident management. In the SAM standard, the combination of hardware and software measures based on the risk assessment enables a scientific and rational approach to apply to scenarios of various severe accidents including low-frequency, high-impact events, and assures safety with functionality and flexibility. The SAM standard is already established in March, 2014. After publication of the SAM standard, with regard to effectiveness assessment for accident management and treatment of the uncertainty of severe accident analysis code, for example, the detailed guideline will be prepared as appendices of the standard. (author)

Dose calculations for severe LWR accident scenarios

International Nuclear Information System (INIS)

Margulies, T.S.; Martin, J.A. Jr.

1984-05-01

This report presents a set of precalculated doses based on a set of postulated accident releases and intended for use in emergency planning and emergency response. Doses were calculated for the PWR (Pressurized Water Reactor) accident categories of the Reactor Safety Study (WASH-1400) using the CRAC (Calculations of Reactor Accident Consequences) code. Whole body and thyroid doses are presented for a selected set of weather cases. For each weather case these calculations were performed for various times and distances including three different dose pathways - cloud (plume) shine, ground shine and inhalation. During an emergency this information can be useful since it is immediately available for projecting offsite radiological doses based on reactor accident sequence information in the absence of plant measurements of emission rates (source terms). It can be used for emergency drill scenario development as well

Severe accident recriticality analyses (SARA)

DEFF Research Database (Denmark)

Frid, W.; Højerup, C.F.; Lindholm, I.

2001-01-01

with all three codes. The core initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality-both super-prompt power bursts and quasi steady-state power......Recriticality in a BWR during reflooding of an overheated partly degraded core, i.e. with relocated control rods, has been studied for a total loss of electric power accident scenario. In order to assess the impact of recriticality on reactor safety, including accident management strategies......, which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal g(-1), was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding rate of 2000 kg s(-1). In most cases, however, the predicted energy deposition was smaller, below...

Molecular structures and thermodynamic properties of monohydrated gaseous iodine compounds: Modelling for severe accident simulation

Science.gov (United States)

Sudolská, Mária; Cantrel, Laurent; Budzák, Šimon; Černušák, Ivan

2014-03-01

Monohydrated complexes of iodine species (I, I2, HI, and HOI) have been studied by correlated ab initio calculations. The standard enthalpies of formation, Gibbs free energy and the temperature dependence of the heat capacities at constant pressure were calculated. The values obtained have been implemented in ASTEC nuclear accident simulation software to check the thermodynamic stability of hydrated iodine compounds in the reactor coolant system and in the nuclear containment building of a pressurised water reactor during a severe accident. It can be concluded that iodine complexes are thermodynamically unstable by means of positive Gibbs free energies and would be represented by trace level concentrations in severe accident conditions; thus it is well justified to only consider pure iodine species and not hydrated forms.

Prevention of heavy missiles during severe PWR accidents

International Nuclear Information System (INIS)

Krieg, R.

1994-01-01

For future pressurized water reactors, which should be designed against core melt down accidents, missiles generated inside the containment present a severe problem for its integrity. The masses and geometries of the missiles as well as their velocities may vary to a great extend. Therefore, a reliable proof of the containment integrity is very difficult. To overcome this problem the potential sources of missiles are discussed. In section 5 it is concluded that the generation of heavy missiles must be prevented. Steam explosions must not damage the reactor vessel head. Thus fragments of the head cannot become missiles endangering the containment shell. Furthermore, during a melt-through failure of the reactor vessel under high pressure the resulting forces must not catapult the whole vessel against the containment shell. Only missiles caused by hydrogen explosions might be tolerable, but shielding structures which protect the containment shell might be required. Here further investigations are necessary. Finally, measures are described showing that the generation of heavy missiles can indeed be prevented. In section 6 investigations are explained which will confirm the strength of the reactor vessel head. In section 7 a device is discussed keeping the fragments of a failing reactor vessel at its place. (author). 12 refs., 8 figs

Development of a prototype graphic simulation program for severe accident training

International Nuclear Information System (INIS)

Kim, Ko Ryu; Jeong, Kwang Sub; Ha, Jae Joo

2000-05-01

This is a report of the development process and related technologies of severe accident graphic simulators, required in industrial severe accident management and training. Here, we say 'a severe accident graphic simulator' as a graphics add-in system to existing calculation codes, which can show the severe accident phenomena dynamically on computer screens and therefore which can supplement one of main defects of existing calculation codes. With graphic simulators it is fairly easy to see the total behavior of nuclear power plants, where it was very difficult to see only from partial variable numerical information. Moreover, the fast processing and control feature of a graphic simulator can give some opportunities of predicting the severe accident advancement among several possibilities, to one who is not an expert. Utilizing graphic simulators' we expect operators' and TSC members' physical phenomena understanding enhancement from the realistic dynamic behavior of plants. We also expect that severe accident training course can gain better training effects using graphic simulator's control functions and predicting capabilities, and therefore we expect that graphic simulators will be effective decision-aids tools both in sever accident training course and in real severe accident situations. With these in mind, we have developed a prototype graphic simulator having surveyed related technologies, and from this development experiences we have inspected the possibility to build a severe accident graphic simulator. The prototype graphic simulator is developed under IBM PC WinNT environments and is suited to Uljin 3and4 nuclear power plant. When supplied with adequate severe accident scenario as an input, the prototype can provide graphical simulations of plant safety systems' dynamic behaviors. The prototype is composed of several different modules, which are phenomena display module, MELCOR data interface module and graphic database interface module. Main functions of

Development of the severe accident risk information database management system SARD

International Nuclear Information System (INIS)

Ahn, Kwang Il; Kim, Dong Ha

2003-01-01

The main purpose of this report is to introduce essential features and functions of a severe accident risk information management system, SARD (Severe Accident Risk Database Management System) version 1.0, which has been developed in Korea Atomic Energy Research Institute, and database management and data retrieval procedures through the system. The present database management system has powerful capabilities that can store automatically and manage systematically the plant-specific severe accident analysis results for core damage sequences leading to severe accidents, and search intelligently the related severe accident risk information. For that purpose, the present database system mainly takes into account the plant-specific severe accident sequences obtained from the Level 2 Probabilistic Safety Assessments (PSAs), base case analysis results for various severe accident sequences (such as code responses and summary for key-event timings), and related sensitivity analysis results for key input parameters/models employed in the severe accident codes. Accordingly, the present database system can be effectively applied in supporting the Level 2 PSA of similar plants, for fast prediction and intelligent retrieval of the required severe accident risk information for the specific plant whose information was previously stored in the database system, and development of plant-specific severe accident management strategies

Development of the severe accident risk information database management system SARD

Energy Technology Data Exchange (ETDEWEB)

Ahn, Kwang Il; Kim, Dong Ha

2003-01-01

The main purpose of this report is to introduce essential features and functions of a severe accident risk information management system, SARD (Severe Accident Risk Database Management System) version 1.0, which has been developed in Korea Atomic Energy Research Institute, and database management and data retrieval procedures through the system. The present database management system has powerful capabilities that can store automatically and manage systematically the plant-specific severe accident analysis results for core damage sequences leading to severe accidents, and search intelligently the related severe accident risk information. For that purpose, the present database system mainly takes into account the plant-specific severe accident sequences obtained from the Level 2 Probabilistic Safety Assessments (PSAs), base case analysis results for various severe accident sequences (such as code responses and summary for key-event timings), and related sensitivity analysis results for key input parameters/models employed in the severe accident codes. Accordingly, the present database system can be effectively applied in supporting the Level 2 PSA of similar plants, for fast prediction and intelligent retrieval of the required severe accident risk information for the specific plant whose information was previously stored in the database system, and development of plant-specific severe accident management strategies.

A framework for the assessment of severe accident management strategies

International Nuclear Information System (INIS)

Kastenberg, W.E.; Apostolakis, G.; Dhir, V.K.

1993-09-01

Severe accident management can be defined as the use of existing and/or altemative resources, systems and actors to prevent or mitigate a core-melt accident. For each accident sequence and each combination of severe accident management strategies, there may be several options available to the operator, and each involves phenomenological and operational considerations regarding uncertainty. Operational uncertainties include operator, system and instrumentation behavior during an accident. A framework based on decision trees and influence diagrams has been developed which incorporates such criteria as feasibility, effectiveness, and adverse effects, for evaluating potential severe accident management strategies. The framework is also capable of propagating both data and model uncertainty. It is applied to several potential strategies including PWR cavity flooding, BWR drywell flooding, PWR depressurization and PWR feed and bleed

A framework for the assessment of severe accident management strategies

Energy Technology Data Exchange (ETDEWEB)

Kastenberg, W.E. [ed.; Apostolakis, G.; Dhir, V.K. [California Univ., Los Angeles, CA (United States). Dept. of Mechanical, Aerospace and Nuclear Engineering] [and others

1993-09-01

Severe accident management can be defined as the use of existing and/or altemative resources, systems and actors to prevent or mitigate a core-melt accident. For each accident sequence and each combination of severe accident management strategies, there may be several options available to the operator, and each involves phenomenological and operational considerations regarding uncertainty. Operational uncertainties include operator, system and instrumentation behavior during an accident. A framework based on decision trees and influence diagrams has been developed which incorporates such criteria as feasibility, effectiveness, and adverse effects, for evaluating potential severe accident management strategies. The framework is also capable of propagating both data and model uncertainty. It is applied to several potential strategies including PWR cavity flooding, BWR drywell flooding, PWR depressurization and PWR feed and bleed.

Predicted occurrence rate of severe transportation accidents involving large casks

International Nuclear Information System (INIS)

Dennis, A.W.

1978-01-01

A summary of the results of an investigation of the severities of highway and railroad accidents as they relate to the shipment of large radioactive materials casks is discussed. The accident environments considered are fire, impact, crash, immersion, and puncture. For each of these environments, the accident severities and their predicted frequencies of occurrence are presented. These accident environments are presented in tabular and graphic form to allow the reader to evaluate the probabilities of occurrence of the accident parameter severities he selects

Development of Information Display System for Operator Support in Severe Accident

International Nuclear Information System (INIS)

Jeong, Kwang Il; Lee, Joon Ku

2016-01-01

When the severe accident occurs, the technical support center (TSC) performs the mitigation strategy with severe accident management guidelines (SAMG) and communicates with main control room (MCR) operators to obtain information of plant's status. In such circumstances, the importance of an information display for severe accident is increased. Therefore an information display system dedicated to severe accident conditions is required to secure the plant information, to provide the necessary information to MCR operators and TSC operators, and to support the decision using these information. We setup the design concept of severe accident information display system (SIDS) in the previous study and defined its requirements of function and performance. This paper describes the process, results of the identification of the severe accident information for MCR operator and the implementation of SIDS. Further implementation on post-accident monitoring function and data validation function for severe accidents will be accomplished in the future

The Effect of External Vessel Cooling for a 2 inch LOCA Severe Accident Scenario at SMART with MIDAS/SMR

International Nuclear Information System (INIS)

Park, Jong Hwa; Kim, Dong Ha; Chung, Young Jong; Park, Sun Hee; Cho, Seong Won

2010-01-01

KAERI is developing a new concept of reactor that all the main components such as the steam generator, the coolant pumps and the pressurizer are located inside the reactor vessel. This feature may prevent the large size of LOCA. However it is necessary to estimate the hypothetical severe accidents progression for improving the degree of safety and identifying the unknown weakness of the system against an accident. To simulate a hypothetical severe accident for the SMART, we adopt the MIDAS/SMR code which was developed by KAERI

Characteristics of the aerosols released to the environment after a severe PWR accident

International Nuclear Information System (INIS)

Lhiaubet, G.; Manesse, D.

1988-05-01

In the event of a postulated severe accident on a pressurized water reactor (PWR) involving fuel degradation, gases and aerosols containing radioactive products could be released, with short, medium and long term consequences for the population and the environment. Under such accident conditions, the ESCADRE code system, developed at IPSN (Institute for Nuclear Safety and Protection) can be used to calculate the properties of the substances released and, especially with the AEROSOLS/B2 code, the main characteristics of the aerosols (concentration, size distribution, composition). For conditions representative of severe PWR accidents, by varying different main parameters (structural material aerosols, steam condensation in the containment, etc...), indications are given on the range of characteristics of the aerosols (containing notably Cs, Te, Sr, Ru, etc...) released to the atmosphere. Information is also given on how more accurate data (especially on the chemical forms) will be obtainable in the framework of current or planned experimental programs (HEVA, PITEAS, PHEBUS PF, etc...) [fr

Experimental study of in-and-ex-vessel melt cooling during a severe accident

Energy Technology Data Exchange (ETDEWEB)

Kim, Sang Baik; Yoo, K J; Park, C K; Seok, S D; Park, R J; Yi, S J; Kang, K H; Ham, Y S; Cho, Y R; Kim, J H; Jeong, J H; Shin, K Y; Cho, J S; Kim, D H

1997-07-01

After code damage during a severe accident in a nuclear reactor, the degraded core has to be cooled down and the decay heat should be removed in order to cease the accident progression and maintain a stable state. The cooling of core melt is divided into in-vessel and ex-vessel cooling depending on the location of molten core which is dependent on the timing of vessel failure. Since the cooling mechanism varies with the conditions of molten core and surroundings and related phenomena, it contains many phenomenological uncertainties so far. In this study, an experimental study for verification of in-vessel corium cooling and several separate effect experiments for ex-vessel cooling are carried out to verify in- and ex-vessel cooling phenomena and finally to develop the accident management strategy and improve engineered reactor design for the severe accidents. SONATA-IV (Simulation of Naturally Arrested Thermal Attack in Vessel) program is set up for in-vessel cooling and a progression of the verification experiment has been done, and an integral verification experiment of the containment integrity for ex-vessel cooling is planned to be carried out based on the separate effect experiments performed in the first phase. First phase study of SONATA-IV is proof of principle experiment and it is composed of LALA (Lower-plenum Arrested Vessel Attack) experiment to find the gap between melt and the lower plenum during melt relocation and to certify melt quenching and CHFG (Critical Heat Flux in Gap) experiment to certify heat transfer mechanism in an artificial gap. As separate effect experiments for ex-vessel cooling, high pressure melt ejection experiment related to the initial condition for debris layer formation in the reactor cavity, crust formation and heat transfer experiment in the molten pool and molten core concrete interaction experiment are performed. (author). 150 refs., 24 tabs., 127 figs.

Swedish REGULATORY APPROACH TO SAFETY Assessment AND SEVERE ACCIDENT MANAGEMENT

International Nuclear Information System (INIS)

Frid, W.; Sandervaag, O.

1997-01-01

The Swedish regulatory approach to safety assessment and severe accident management is briefly described. The safety assessment program, which focuses on prevention of incidents and accidents, has three main components: periodic safety reviews, probabilistic safety analysis, and analysis of postulated disturbances and accident progression sequences. Management and man-technology-organisation issues, as well as inspections, play a key role in safety assessment. Basis for severe accident management were established by the Government decisions in 1981 and 1986. By the end of 1988, the severe accident mitigation systems and emergency operating procedures were implemented at all Swedish reactors. The severe accident research has continued after 1988 for further verification of the protection provided by the systems and reduction of remaining uncertainties in risk dominant phenomena

Simplified methods to the complete thermal and mechanical behavior of a pressure vessel during a severe accident

International Nuclear Information System (INIS)

Dupas, P.; Schneiter, J.R.

1996-01-01

EDF has developed a software package of simplified methods (proprietary ones or from literature) in order to study the thermal and mechanical behavior of a PWR pressure vessel during a severe accident involving a corium localization in the vessel lower head. Using a part of this package, the authors can evaluate for instance successively: the heat flux at the inner surface of the vessel (conductive or convective pool of corium); the thermal exchange coefficient between the vessel and the outside (dry pit or flooded pit, watertight thermal insulation or not); the complete thermal evolution of the vessel (temperature profile, melting); the possible global plastic failure of the vessel; the creep behavior in the thickness of the vessel. These simplified methods are a cost effective alternative to finite element calculations which are yet used to validate the previous methods, waiting for experimental results to come

Development of Information Display System for Operator Support in Severe Accident

Energy Technology Data Exchange (ETDEWEB)

Jeong, Kwang Il; Lee, Joon Ku [KAERI, Daejeon (Korea, Republic of)

2016-05-15

When the severe accident occurs, the technical support center (TSC) performs the mitigation strategy with severe accident management guidelines (SAMG) and communicates with main control room (MCR) operators to obtain information of plant's status. In such circumstances, the importance of an information display for severe accident is increased. Therefore an information display system dedicated to severe accident conditions is required to secure the plant information, to provide the necessary information to MCR operators and TSC operators, and to support the decision using these information. We setup the design concept of severe accident information display system (SIDS) in the previous study and defined its requirements of function and performance. This paper describes the process, results of the identification of the severe accident information for MCR operator and the implementation of SIDS. Further implementation on post-accident monitoring function and data validation function for severe accidents will be accomplished in the future.

Development of a prototype graphic simulation program for severe accident training

Energy Technology Data Exchange (ETDEWEB)

Kim, Ko Ryu; Jeong, Kwang Sub; Ha, Jae Joo

2000-05-01

This is a report of the development process and related technologies of severe accident graphic simulators, required in industrial severe accident management and training. Here, we say 'a severe accident graphic simulator' as a graphics add-in system to existing calculation codes, which can show the severe accident phenomena dynamically on computer screens and therefore which can supplement one of main defects of existing calculation codes. With graphic simulators it is fairly easy to see the total behavior of nuclear power plants, where it was very difficult to see only from partial variable numerical information. Moreover, the fast processing and control feature of a graphic simulator can give some opportunities of predicting the severe accident advancement among several possibilities, to one who is not an expert. Utilizing graphic simulators' we expect operators' and TSC members' physical phenomena understanding enhancement from the realistic dynamic behavior of plants. We also expect that severe accident training course can gain better training effects using graphic simulator's control functions and predicting capabilities, and therefore we expect that graphic simulators will be effective decision-aids tools both in sever accident training course and in real severe accident situations. With these in mind, we have developed a prototype graphic simulator having surveyed related technologies, and from this development experiences we have inspected the possibility to build a severe accident graphic simulator. The prototype graphic simulator is developed under IBM PC WinNT environments and is suited to Uljin 3and4 nuclear power plant. When supplied with adequate severe accident scenario as an input, the prototype can provide graphical simulations of plant safety systems' dynamic behaviors. The prototype is composed of several different modules, which are phenomena display module, MELCOR data interface module and graphic database

Analyzing the severity of accidents on the German Autobahn.

Science.gov (United States)

Manner, Hans; Wünsch-Ziegler, Laura

2013-08-01

We study the severity of accidents on the German Autobahn in the state of North Rhine-Westphalia using data for the years 2009 until 2011. We use a multinomial logit model to identify statistically relevant factors explaining the severity of the most severe injury, which is classified into the four classes fatal, severe injury, light injury and property damage. Furthermore, to account for unobserved heterogeneity we use a random parameter model. We study the effect of a number of factors including traffic information, road conditions, type of accidents, speed limits, presence of intelligent traffic control systems, age and gender of the driver and location of the accident. Our findings are in line with studies in different settings and indicate that accidents during daylight and at interchanges or construction sites are less severe in general. Accidents caused by the collision with roadside objects, involving pedestrians and motorcycles, or caused by bad sight conditions tend to be more severe. We discuss the measures of the 2011 German traffic safety programm in the light of our results. Copyright © 2013 Elsevier Ltd. All rights reserved.

Revised Severe Accident Research Program plan, FY 1990--1992

International Nuclear Information System (INIS)

1989-08-01

For the past 10 years, since the Three Mile Island accident, the NRC has sponsored an active research program on light-water-reactor severe accidents as part of a multi-faceted approach to reactor safety. This report describes the revised Severe Accident Research Program (SARP) and how the revisions are designed to provide confirmatory information and technical support to the NRC staff in implementing the staff's Integration Plan for Closure of Severe Accident Issues as described in SECY-88-147. The revised SARP addresses both the near-term research directed at providing a technical basis upon which decisions on important containment performance issues can be made and the long-term research needed to confirm and refine our understanding of severe accidents. In developing this plan, the staff recognized that the overall goal is to reduce the uncertainties in the source term sufficiently to enable the staff to make regulatory decisions on severe accident issues. However, the staff also recognized that for some issues it may not be practical to attempt to further reduce uncertainties, and some regulatory decisions or conclusions will have to be made with full awareness of existing uncertainties. 2 figs., 1 tab

A multivariate tobit analysis of highway accident-injury-severity rates.

Science.gov (United States)

Anastasopoulos, Panagiotis Ch; Shankar, Venky N; Haddock, John E; Mannering, Fred L

2012-03-01

Relatively recent research has illustrated the potential that tobit regression has in studying factors that affect vehicle accident rates (accidents per distance traveled) on specific roadway segments. Tobit regression has been used because accident rates on specific roadway segments are continuous data that are left-censored at zero (they are censored because accidents may not be observed on all roadway segments during the period over which data are collected). This censoring may arise from a number of sources, one of which being the possibility that less severe crashes may be under-reported and thus may be less likely to appear in crash databases. Traditional tobit-regression analyses have dealt with the overall accident rate (all crashes regardless of injury severity), so the issue of censoring by the severity of crashes has not been addressed. However, a tobit-regression approach that considers accident rates by injury-severity level, such as the rate of no-injury, possible injury and injury accidents per distance traveled (as opposed to all accidents regardless of injury-severity), can potentially provide new insights, and address the possibility that censoring may vary by crash-injury severity. Using five-year data from highways in Washington State, this paper estimates a multivariate tobit model of accident-injury-severity rates that addresses the possibility of differential censoring across injury-severity levels, while also accounting for the possible contemporaneous error correlation resulting from commonly shared unobserved characteristics across roadway segments. The empirical results show that the multivariate tobit model outperforms its univariate counterpart, is practically equivalent to the multivariate negative binomial model, and has the potential to provide a fuller understanding of the factors determining accident-injury-severity rates on specific roadway segments. Published by Elsevier Ltd.

A framework for assessing severe accident management strategies

International Nuclear Information System (INIS)

Kastenberg, W.E.; Apostolakis, G.; Dhir, V.K.; Okrent, D.; Jae, M.; Lim, H.; Milici, T.; Park, H.; Swider, J.; Xing, L.; Yu, D.

1991-01-01

Accident management can be defined as the innovative use of existing and or alternative resources, systems and actions to prevent or mitigate a severe accident. Together with risk management (changes in plant operation and/or addition of equipment) and emergency planning (off-site actions), accident management provides an extension of the defense-in-depth safety philosophy for severe accidents. A significant number of probabilistic safety assessments (PSA) have been completed which yield the principal plant vulnerabilities. For each sequence/threat and each combination of strategy there may be several options available to the operator. Each strategy/option involves phenomenological and operational considerations regarding uncertainty. These considerations include uncertainty in key phenomena, uncertainty in operator behavior, uncertainty in system availability and behavior, and uncertainty in available information (i.e., instrumentation). The objective of this project is to develop a methodology for assessing severe accident management strategies given the key uncertainties mentioned above. Based on Decision Trees and Influence Diagrams, the methodology is currently being applied to two case studies: cavity flooding in a PWR to prevent vessel penetration or failure, and drywell flooding in a BWR to prevent containment failure

Numerical Analysis of Molten Corium Dispersion during Hypothetical High-Pressure Accidents in APR1400 Nuclear Power Plant

International Nuclear Information System (INIS)

Kim, Jong Tae; Ha, Kwang Soon; Kim, Sang Baik; Kim, Hee Dong; Jeong, Jae Sik

2010-01-01

During a hypothetical high-pressure accident in a nuclear power plant (NPP), molten corium can be ejected through a breach of a reactor pressure vessel (RPV) and dispersed by the following jet of a high pressure steam in the RPV. The dispersed corium is fragmented into smaller droplets in a reactor cavity of the NPP by the steam jet with very high velocity and is released into the upper compartment of the NPP by an overpressure in the cavity. The heat-carrying fragments of the corium transfer the thermal energy to the ambient air in the containment and react chemically with steam and generate hydrogen which may be burnt in the containment. The thermal loads from the ejected molten corium on the containment which is called direct containment heating (DCH) can threaten the integrity of the containment. New generation NPPs such as APR1400 and EPR have been designed in consideration of reducing the possibility of the containment failure from the DCH. In order for that, APR1400 has a convolute-type corium chamber connected to the reactor cavity. In the case of EPR, severe-accident dedicated depressurization valves are installed to preclude a high pressure melt ejection (HPME). DCH in a NPP containment is related to many physical phenomena such as multi-phase hydrodynamics, thermodynamics and chemical reaction. In the evaluation of the DCH load, the melt dispersion rates depending on the RPV pressure are the most important parameter. Mostly, DCH was evaluated by using lumped-analysis codes with some correlations obtained from experiments for the dispersion rates. The corium dispersion rates for many types of the NPP containments had been obtained by experiments in 90s. And some correlations from the experimental data were developed. As mentioned above, APR1400 has a corium chamber to reduce the corium dispersion rate. But there is no experimental data for the dispersion rate specific to the APR1400 cavity geometry. So its performance for capturing of the dispersed corium

CANDU safety under severe accidents

International Nuclear Information System (INIS)

Snell, V.G.; Howieson, J.Q.; Frescura, G.M.; King, F.; Rogers, J.T.; Tamm, H.

1988-01-01

The characteristics of the CANDU reactor relevant to severe accidents are set first by the inherent properties of the design, and second by the Canadian safety/licensing approach. Probabilistic safety assessment studies have been performed on operating CANDU plants, and on the 4 x 880 MW(e) Darlington station now under construction; furthermore a scoping risk assessment has been done for a CANDU 600 plant. They indicate that the summed severe core damage frequency is of the order of 5 x 10 -6 /year. CANDU nuclear plant designers and owner/operators share information and operational experience nationally and internationally through the CANDU Owners' Group (COG). The research program generally emphasizes the unique aspects of the CANDU concept, such as heat removal through the moderator, but it has also contributed significantly to areas generic to most power reactors such as hydrogen combustion, containment failure modes, fission product chemistry, and high temperature fuel behaviour. Abnormal plant operating procedures are aimed at first using event-specific emergency operating procedures, in cases where the event can be diagnosed. If this is not possible, generic procedures are followed to control Critical Safety Parameters and manage the accident. Similarly, the on-site contingency plans include a generic plan covering overall plant response strategy, and a specific plan covering each category of contingency

Benchmarking Severe Accident Computer Codes for Heavy Water Reactor Applications

International Nuclear Information System (INIS)

2013-12-01

Requests for severe accident investigations and assurance of mitigation measures have increased for operating nuclear power plants and the design of advanced nuclear power plants. Severe accident analysis investigations necessitate the analysis of the very complex physical phenomena that occur sequentially during various stages of accident progression. Computer codes are essential tools for understanding how the reactor and its containment might respond under severe accident conditions. The IAEA organizes coordinated research projects (CRPs) to facilitate technology development through international collaboration among Member States. The CRP on Benchmarking Severe Accident Computer Codes for HWR Applications was planned on the advice and with the support of the IAEA Nuclear Energy Department's Technical Working Group on Advanced Technologies for HWRs (the TWG-HWR). This publication summarizes the results from the CRP participants. The CRP promoted international collaboration among Member States to improve the phenomenological understanding of severe core damage accidents and the capability to analyse them. The CRP scope included the identification and selection of a severe accident sequence, selection of appropriate geometrical and boundary conditions, conduct of benchmark analyses, comparison of the results of all code outputs, evaluation of the capabilities of computer codes to predict important severe accident phenomena, and the proposal of necessary code improvements and/or new experiments to reduce uncertainties. Seven institutes from five countries with HWRs participated in this CRP

Phenomenology of severe accidents in BWR type reactors. First part

International Nuclear Information System (INIS)

Sandoval V, S.

2003-01-01

A Severe Accident in a nuclear power plant is a deviation from its normal operating conditions, resulting in substantial damage to the core and, potentially, the release of fission products. Although the occurrence of a Severe Accident on a nuclear power plant is a low probability event, due to the multiple safety systems and strict safety regulations applied since plant design and during operation, Severe Accident Analysis is performed as a safety proactive activity. Nuclear Power Plant Severe Accident Analysis is of great benefit for safety studies, training and accident management, among other applications. This work describes and summarizes some of the most important phenomena in Severe Accident field and briefly illustrates its potential use based on the results of two generic simulations. Equally important and abundant as those here presented, fission product transport and retention phenomena are deferred to a complementary work. (Author)

Developing a knowledge base for the management of severe accidents

International Nuclear Information System (INIS)

Nelson, W.R.; Jenkins, J.P.

1986-01-01

Prior to the accident at Three Mile Island, little attention was given to the development of procedures for the management of severe accidents, that is, accidents in which the reactor core is damaged. Since TMI, however, significant effort has been devoted to developing strategies for severe accident management. At the same time, the potential application of artificial intelligence techniques, particularly expert systems, to complex decision-making tasks such as accident diagnosis and response has received considerable attention. The need to develop strategies for accident management suggests that a computerized knowledge base such as used by an expert system could be developed to collect and organize knowledge for severe accident management. This paper suggests a general method which could be used to develop such a knowledge base, and how it could be used to enhance accident management capabilities

Iodine chemistry effect on source term assessments. A MELCOR 186 YT study of a PWR severe accident sequence

International Nuclear Information System (INIS)

Herranz, Luis E.; Garcia, Monica; Otero, Bernadette

2009-01-01

Level-2 Probabilistic Safety Analysis has demonstrated to be a powerful tool to give insights into multiple aspects concerning severe accidents: phenomena with the greatest potential to lead to containment failure, safety systems performance and, even, to identify any additional accident management that could mitigate the consequences of such an even, etc. A major result of level-2 PSA is iodine content in Source Term since it is the main responsible for the radiological impact during the first few days after a hypothetical severe accident. Iodine chemistry is known to considerably affect iodine behavior and although understanding has improved substantially since the early 90's, a thorough understanding is still missing and most PSA studies do not address it when assessing severe accident scenarios. This paper emphasizes the quantitative and qualitative significance of considering iodine chemistry in level-2 PSA estimates. To do so a cold leg break, low pressure severe accident sequence of an actual pressurized water reactor has been analyzed with the MELCOR 1.8.6 YT code. Two sets of calculations, with and without chemistry, have been carried out and compared. The study shows that iodine chemistry could result in an iodine release to environment about twice higher, most of which would consist of around 60% of iodine in gaseous form. From these results it is concluded that exploratory studies on the potential effect of iodine chemistry on source term estimates should be carried out. (author)

A direct comparison of MELCOR 1.8.3 and MAAP4 results for several PWR ampersand BWR accident sequences

International Nuclear Information System (INIS)

Leonard, M.T.; Ashbaugh, S.G.; Cole, R.K.; Bergeron, K.D.; Nagashima, K.

1996-01-01

This paper presents a comparison of calculations of severe accident progression for several postulated accident sequences for representative Pressurized Water Reactors (PWR) and Boiling Water Reactors (BWR) nuclear power plants performed with the MELCOR 1.8.3 and the MAAP4 computer codes. The PWR system examined in this study is a 1100 MWe system similar in design to a Westinghouse 3-loop plant with a large dry containment; the BWR is a 1100 MWe system similar in design to General Electric BWR/4 with a Mark I containment. A total of nine accident sequences were studied with both codes. Results of these calculations are compared to identify major differences in the timing of key events in the calculated accident progression or other important aspects of severe accident behavior, and to identify specific sources of the observed differences

A PC Mathcad-based computational aid for severe accident analysis and its application to a BWR small LOCA sequence

International Nuclear Information System (INIS)

Wu, Laung-Kuang T.; Lee, S.J.

2004-01-01

A PC-based Mathcad program is used to develop a computational aid for analyzing severe accident phenomena. This computational aid uses simple engineering expressions and empirical correlations to estimate key quantities and timings at various stages of accident progressions. In this paper, the computational aid is applied to analyze an early phase of a BWR small LOCA sequence. The accident phenomena analyzed include: break flow rates, boiled-up water level in the core, core uncovery time, depressurization of the reactor pressure vessel, core heat-up, onset of clad oxidation, hydrogen generation, and onset of fuel relocation. The results are compared with those obtained running the MAAP 3.0B code. This PC-based computational aid can be used to train plant personnel in understanding severe accident phenomena and to assist them in managing severe accidents. (author)

[Characterization of severe acute occupational poisoning accidents in China between 1989 and 2003].

Science.gov (United States)

Zhang, Min; Li, Tao; Wang, Huan-Qiang; Wang, Hong-Fei; Chen, Shu-Yang; Du, Xie-Yi; Zhang, Shuang; Qin, Jian

2006-12-01

To analyze severe acute occupational poisoning accidents reported in China between 1989 and 2003, and to study the characteristics of severe acute occupational poisoning accidents and provide scientific evidences for prevention and control strategies. The data from the national occupational poisoning case reporting system were analyzed with descriptive methods. (1) There were 506 acute severe occupational poisoning accidents for 15 years with 4 657 workers poisoned. The total poisoning rate was 54.8%, and the total mortality was 16.5%. The average poisoning age was (31.9 +/- 9.8) years old and the average death age was (33.7 +/- 10.3) years old. The poisoning accidents occurred more in men than in women. (2) There were more than 112 chemicals which caused these poisoning accidents. Most of the accidents caused by hydrogen sulfide, carbon monoxide, benzene and homologs, metal and metalloid and carbon dioxide, and the types of chemicals varied in different types of industries. (3) The accidents mainly occurred in chemical industry, manufacture, water disposal industry, mining and construction industry, and the risk was higher in some jobs than others, such as cleanout, machine maintenance and repair, production, mine and digging. The accidents occurred more frequently from April to August each year. (1) The control over the severe acute occupational poisoning is urgent. (2) The trend of the characteristics of severe acute occupational poisoning accidents is centralized in the high risk industries, poisons and jobs. (3) The characteristics of the accidents varied in different types of industries. (4) It is the key point to strengthen the supervision on poisoning.

The management of severe accidents

International Nuclear Information System (INIS)

Pelce, J.; Brignon, P.

1987-01-01

In considering severe accidents in water power reactors, a major problem that arises is how to manage them in such a way that the situation can be controlled as well as possible, from the aspects both of preventing serious damage to the core of limiting the discharge of radioactivity. A number of countries have announced provisions in the field of accident management, some already set up, others planned, but these mainly apply to preventing damage to the core. Part of this report deals with this aspect, to show that there is a fairly wide consensus on how problems should be approached. Attitudes vary, on the other hand, in the approach to mitigate radioactive release. In fact, few countries have proposed concrete steps to manage severe accidents in the final stages when the core is seriously damaged. Since it is difficult to compare different approaches, only the French approach is described. This description is however very brief, because in the five or six years since it was defined, the approach has been presented many times. The stress is placed more on the comments which this type of approach suggests, to make the subsequent general discussion easier

Containment severe accident management - selected strategies

International Nuclear Information System (INIS)

Duco, J.; Royen, J.; Rohde, J.; Frid, W.; De Boeck, B.

1994-01-01

The OECD Nuclear Energy Agency (NEA) organized in June 1994, in collaboration with the Swedish Nuclear Power Inspectorate (SKI), a Specialist Meeting on Selected Containment Severe Accident Management Strategies, to discuss their feasibility, effectiveness, benefits and drawbacks, and long-term impact. The meeting focused on water reactors, mainly on existing systems. The technical content covered topics such as general aspects of accident management strategies in OECD Member countries, hydrogen management techniques and other containment accident management strategies, surveillance and protection of the containment function. The main conclusions of the meeting are summarized in the paper. (author)

Study on mitigation of in-vessel release of fission products in severe accidents of PWR

International Nuclear Information System (INIS)

Huang, G.F.; Tong, L.L.; Li, J.X.; Cao, X.W.

2010-01-01

Research highlights: → In-vessel release of fission products in severe accidents for 600 MW PWR is analyzed. → Mitigation effect of primary feed-and-bleed on in-vessel release is investigated. → Mitigation effect of secondary feed-and-bleed on in-vessel release is studied. → Mitigation effect of ex-vessel cooling on in-vessel release is evaluated. - Abstract: During the severe accidents in a nuclear power plant, large amounts of fission products release with accident progression, including in-vessel and ex-vessel release. Mitigation of fission products release is demanded for alleviating radiological consequence in severe accidents. Mitigation countermeasures to in-vessel release are studied for Chinese 600 MW pressurized water reactor (PWR), including feed-and-bleed in primary circuit, feed-and-bleed in secondary circuit and ex-vessel cooling. SBO, LOFW, SBLOCA and LBLOCA are selected as typical severe accident sequences. Based on the evaluation of in-vessel release with different startup time of countermeasure, and the coupling relationship between thermohydraulics and in-vessel release of fission products, some results are achieved. Feed-and-bleed in primary circuit is an effective countermeasure to mitigate in-vessel release of fission products, and earlier startup time of countermeasure is more feasible. Feed-and-bleed in secondary circuit is also an effective countermeasure to mitigate in-vessel release for most severe accident sequences that can cease core melt progression, e.g. SBO, LOFW and SBLOCA. Ex-vessel cooling has no mitigation effect on in-vessel release owing to inevitable core melt and relocation.

Review of severe accidents and the results of accident consequence assessment in different energy systems (Contract research)

International Nuclear Information System (INIS)

Matsuki, Yoshio; Muramatsu, Ken

2008-05-01

The cases of severe accidents and the consequence assessments in different energy systems, Coal, Oil, Gas, Hydro and Nuclear, were collected, and then they were further analyzed. In this report, the information on the accidents in various energy systems were collected from the sources of the Paul Scherrer Institute (hereinafter, 'PSI') and the International Atomic Energy Agency (hereinafter, 'IAEA'). The information on the severe accidents of nuclear power plants were collected from the report of the US Presidential Commission on Catastrophic Nuclear Accidents and several relevant reports issued in the countries of the European Union, together with the reports of the PSI and the IAEA. To analyze the collected information, several parameters, which are numbers of fatalities, injuries, evacuees and the costs of the damages, were chosen to characterize those accidents in different energy systems. And then, upon the comparison of these characteristics of different accidents, the impacts of the accidents in nuclear and other energy systems were compared. Upon the results of the analysis, it is pointed out that the cost caused by the Chernobyl Accident, the severe accident in nuclear energy, tends to be higher than in the other energy systems. On the other hand, from the aspects of fatalities and injuries, it is not confirmed that the damages of the Chernobyl Accident are larger than in the other energy systems. However, it is also recognized, as the specific characteristics of the severe nuclear accident, that the impacts of the accident spread in a wider area, and stay for a longer period, in comparison with the ones in the other energy systems. (author)

Factors associated with urban non-fatal road-accident severity.

Science.gov (United States)

Potoglou, Dimitris; Carlucci, Fabio; Cirà, Andrea; Restaino, Marialuisa

2018-02-05

This paper reports on the factors associated with non-fatal urban-road accident severity. Data on accidents were gathered from the local traffic police in the City of Palermo, one of the six most populated cities in Italy. Findings from a mixed-effects logistic-regression model suggest that accident severity increases when two young drivers are involved, road traffic conditions are light/normal and when vehicles crash on a two-way road or carriageway. Speeding is more likely to cause slight or serious injury even when compared to a vehicle moving towards the opposite direction of traffic. An accident during the summer is more likely to result in a slight or serious injury than an accident during the winter, which is in line with evidence from Southern Europe and the Middle East. Finally, the severity of non-fatal accident injuries in an urban area of Southern Europe was significantly associated with speeding, the age of the driver and seasonality.

Severe accident management guidelines

International Nuclear Information System (INIS)

Uhle, Jennifer

2014-01-01

The events at Fukushima Daiichi have highlighted the importance of Severe Accident Management Guidelines (SAMGs). As the world has learned from the catastrophe and countries are considering changes to their nuclear regulatory programs, the content of SAMGs and their regulatory control are being evaluated. This presentation highlights several factors that are being addressed in the United States as rulemaking is underway pertaining to SAMGs. The question of how to be prepared for the unexpected is discussed with specific insights gleaned from Fukushima. (author)

Simplified methods applied to the complete thermal and mechanical behaviour of a pressure vessel during a severe accident

International Nuclear Information System (INIS)

Dupas, P.

1996-01-01

EDF has developed a software package of simplified methods (proprietary ones from literature) in order to study the thermal and mechanical behaviour of a PWR pressure vessel during a severe accident involving a corium localization in the vessel lower head. Using a part of this package, we can evaluate for instance successively: the heat flux at the inner surface of the vessel (conductive or convective pool of corium); the thermal exchange coefficient between the vessel and the outside (dry pit or flooded pit, watertight thermal insulation or not); the complete thermal evolution of the vessel (temperature profile, melting); the possible global plastic failure of the vessel; the creep behaviour in the vessel. These simplified methods are low cost alternative to finite element calculations which are yet used to validate the previous methods, waiting for experimental results to come. (authors)

ACR-1000: Enhanced response to severe accidents

International Nuclear Information System (INIS)

Popov, N.K.; Santamaura, P.; Shapiro, H.; Snell, V.G.

2006-01-01

Full text: Atomic Energy of Canada Limited (AECL) developed the Advanced CANDU Reactor-TM700 (ACR-700TM) as an evolutionary advancement of the current CANDU 6R reactor. As further advancement of the ACR design, AECL is currently developing the ACR-1000TM for the Canadian and international market. The ACR-1000 is aimed at producing electrical power for a capital cost and a unit-energy cost significantly less than that of the current generation of operating nuclear plants, while achieving shorter construction schedule, high plant capacity factor, improved operations and maintenance, increased operating life. and enhanced safety features. The reference ACR-1000 plant design is based on an integrated two-unit plant, using enriched fuel and light-water coolant, with each unit having a nominal gross output of about 1200 MWe. This paper presents the ACR-1000 features that are designed to mitigate limited core damage and severe core damage states, including core retention within vessel, core damage termination, and containment integrity maintenance. Core retention within vessel in CANDU-type reactors includes both retention within fuel channels, and retention within the calandria vessel. The moderator heavy water in the ACR-1000 calandria vessel, as in any other CANDU-type reactor, provides ample heat removal capacity in severe accidents. The ACR-1000 calandria vessel design permits for passive rejection of decay heat from the moderator to the shield water. Also, the calandria vessel will be designed for debris retention. Core damage termination is achieved by flooding of the core components with water and keeping them flooded thereafter. Successful termination can be achieved in the fuel channels, calandria vessel or calandria vault by water supply by the Long Term Cooling (LTC) pumps and by gravity feed from the Reserve Water System. The ACR-1000 containment is required to withstand external events such as earthquakes, tornados, floods and aircraft crashes. Containment

Development of severe accident management guidance for Younggwang units 5 and 6

International Nuclear Information System (INIS)

Lee, K. W.; Beon, C. S.; Kim, M. K.; Hong, S. Y.; Park, K. S.

2001-01-01

Severe Accident Management Guidance (SAMG) has been developed for Younggwang Units 5 and 6. It is consisted of Severe Accident Control Room Guideline, Diagnostic Flow Chart, Severe Accident Guideline, Severe Challenge Guideline, TSC Long Term Monitoring, SAMG Termination. Severe Accident Control Room Guideline, which deals with severe accident after finishing Emergency Operation Procedure, consists of acitions before and after TSC actuation. Seven servere accident management strategies are developed. Diagnostic Flow Chart, Severe Accident Guideline, and Severe Challenge Guideline are developed for each strategy, which enables the users to the implementation of strategy easily and systematically. TSC Long Term Monitoring is also developed to monitor long term activities after a particular strategy. Total of 45 set points are developed for decision making during the implementation of the SAMG

Accomplishments and challenges of the severe accident research

International Nuclear Information System (INIS)

Sehgal, B.R.

2001-01-01

This paper briefly describes the progress of the severe accident research since 1980, in terms of the accomplishments made so far and the challenges that remain. Much has been accomplished: many important safety issues have been resolved and consensus is near on some others. However, some of the previously identified safety issues remain as challenges, while some new ones have arisen due to the shift in focus from containment to vessel integrity. New reactor designs have also created some new challenges. In general, the regulatory demands for new reactor designs are stricter, thereby requiring much greater attention to the safety issues concerned with the containment design of the new large reactors, and to the accident management procedures for mitigating the consequences of a severe accident. We apologize for not providing references to many fine investigations that contributed to the great progress made so far in the severe accident research

Prediction of hydrogen concentration in nuclear power plant containment under severe accidents using cascaded fuzzy neural networks

Energy Technology Data Exchange (ETDEWEB)

Choi, Geon Pil; Kim, Dong Yeong; Yoo, Kwae Hwan; Na, Man Gyun, E-mail: magyna@chosun.ac.kr

2016-04-15

Highlights: • We present a hydrogen-concentration prediction method in an NPP containment. • The cascaded fuzzy neural network (CFNN) is used in this prediction model. • The CFNN model is much better than the existing FNN model. • This prediction can help prevent severe accidents in NPP due to hydrogen explosion. - Abstract: Recently, severe accidents in nuclear power plants (NPPs) have attracted worldwide interest since the Fukushima accident. If the hydrogen concentration in an NPP containment is increased above 4% in atmospheric pressure, hydrogen combustion will likely occur. Therefore, the hydrogen concentration must be kept below 4%. This study presents the prediction of hydrogen concentration using cascaded fuzzy neural network (CFNN). The CFNN model repeatedly applies FNN modules that are serially connected. The CFNN model was developed using data on severe accidents in NPPs. The data were obtained by numerically simulating the accident scenarios using the MAAP4 code for optimized power reactor 1000 (OPR1000) because real severe accident data cannot be obtained from actual NPP accidents. The root-mean-square error level predicted by the CFNN model is below approximately 5%. It was confirmed that the CFNN model could accurately predict the hydrogen concentration in the containment. If NPP operators can predict the hydrogen concentration in the containment using the CFNN model, this prediction can assist them in preventing a hydrogen explosion.

Filtra-MVSS mitigates the consequences of a severe reactor accident

International Nuclear Information System (INIS)

Lindau, L.; Gustavsson, L.; Elisson, K.

1989-01-01

The purpose of the filter system, known as Filtra-MVSS (for Multi-Venturi Scrubber System) is to provide pressure relief for the reactor containment and to limit radioactive releases in the event of a reactor accident, thereby largely preventing local radioactive fall-out. To this end the pressure is reduced in a controlled manner and the discharged steam and gases are washed in a multi-venturi scrubber before release. The system is flexible and can cope with a number of hypothetical accident scenarios

Knowledge data base for severe accident management of nuclear power plants

International Nuclear Information System (INIS)

Ogino, Masao; Kawabe, Ryuhei; Nagasaka, Hideo; Sumida, Susumu; Fukasawa, Masanori; Muta, Hitoshi

2011-01-01

For the reinforcement of the safety of NPPs, the continuous efforts are very important to take in the up-to-date scientific and technical knowledge positively and to reflect them into the safety regulation. The purpose of this present study is to gather effectively the scientific and technical knowledge about the severe accident (SA) phenomena and the accident management (AM) for prevention and mitigation of severe accident, and to take in the experimental data by participating in the international cooperative experiments regarding the important SA phenomena and the effectiveness of accident management. Based on those data and knowledge, JNES is developing and improving severe accident analysis models to maintain the severe accident analysis codes and the accident management knowledge base for assessment of the NPPs in Japan. The activities in fiscal year 2010 are as follows; Experimental study on OECD/NEA projects such as MCCI, SERENA, SFP and international cooperative PSI-ARTIST project, and analytical study on accident management review of new plant and making regulation for severe accident. (author)

Accident source terms for pressurized water reactors with high-burnup cores calculated using MELCOR 1.8.5.

Energy Technology Data Exchange (ETDEWEB)

Gauntt, Randall O.; Powers, Dana Auburn; Ashbaugh, Scott G.; Leonard, Mark Thomas; Longmire, Pamela

2010-04-01

In this study, risk-significant pressurized-water reactor severe accident sequences are examined using MELCOR 1.8.5 to explore the range of fission product releases to the reactor containment building. Advances in the understanding of fission product release and transport behavior and severe accident progression are used to render best estimate analyses of selected accident sequences. Particular emphasis is placed on estimating the effects of high fuel burnup in contrast with low burnup on fission product releases to the containment. Supporting this emphasis, recent data available on fission product release from high-burnup (HBU) fuel from the French VERCOR project are used in this study. The results of these analyses are treated as samples from a population of accident sequences in order to employ approximate order statistics characterization of the results. These trends and tendencies are then compared to the NUREG-1465 alternative source term prescription used today for regulatory applications. In general, greater differences are observed between the state-of-the-art calculations for either HBU or low-burnup (LBU) fuel and the NUREG-1465 containment release fractions than exist between HBU and LBU release fractions. Current analyses suggest that retention of fission products within the vessel and the reactor coolant system (RCS) are greater than contemplated in the NUREG-1465 prescription, and that, overall, release fractions to the containment are therefore lower across the board in the present analyses than suggested in NUREG-1465. The decreased volatility of Cs2MoO4 compared to CsI or CsOH increases the predicted RCS retention of cesium, and as a result, cesium and iodine do not follow identical behaviors with respect to distribution among vessel, RCS, and containment. With respect to the regulatory alternative source term, greater differences are observed between the NUREG-1465 prescription and both HBU and LBU predictions than exist between HBU and LBU

Experiments on aerosol removal by high-pressure water spray

Energy Technology Data Exchange (ETDEWEB)

Corno, Ada del, E-mail: delcorno@rse-web.it [RSE, Power Generation Technologies and Materials Dept, via Rubattino 54, I-20134 Milano (Italy); Morandi, Sonia, E-mail: morandi@rse-web.it [RSE, Power Generation Technologies and Materials Dept, via Rubattino 54, I-20134 Milano (Italy); Parozzi, Flavio, E-mail: parozzi@rse-web.it [RSE, Power Generation Technologies and Materials Dept, via Rubattino 54, I-20134 Milano (Italy); Araneo, Lucio, E-mail: lucio.araneo@polimi.it [Politecnico di Milano, Department of Energy, via Lambruschini 4A, I-20156 Milano (Italy); CNR-IENI, via Cozzi 53, I-20125 Milano (Italy); Casella, Francesco, E-mail: francesco2.casella@mail.polimi.it [Politecnico di Milano, Department of Energy, via Lambruschini 4A, I-20156 Milano (Italy)

2017-01-15

Highlights: • Experimental research to measure the efficiency of high-pressure sprays in capturing aerosols if applied to a filtered containment venting system in case of severe accident. • Cloud of monodispersed SiO{sub 2} particles with sizes 0.5 or 1.0 μm and initial concentration in the range 2–90 mg/m{sup 3}. • Carried out in a chamber 0.5 × 1.0 m and 1.5 m high, with transparent walls equipped with a high pressure water spray with single nozzle. • Respect to low-pressure sprays, removal efficiency turned out significant: the half-life for 1 μm particles with a removal high-pressure spray system is orders of magnitude shorter than that with a low-pressure sprays system. - Abstract: An experimental research was managed in the framework of the PASSAM European Project to measure the efficiency of high-pressure sprays in capturing aerosols when applied to a filtered containment venting system in case of severe accident. The campaign was carried out in a purposely built facility composed by a scrubbing chamber 0.5 × 1.0 m and 1.5 m high, with transparent walls to permit the complete view of the aerosol removal process, where the aerosol was injected to form a cloud of specific particle concentration. The chamber was equipped with a high pressure water spray system with a single nozzle placed on its top. The test matrix consisted in the combination of water pressure injections, in the range 50–130 bar, on a cloud of monodispersed SiO{sub 2} particles with sizes 0.5 or 1.0 μm and initial concentration ranging between 2 and 99 mg/m{sup 3}. The spray was kept running for 2 min and the efficiency of the removal was evaluated, along the test time, using an optical particle sizer. With respect to low-pressure sprays, the removal efficiency turned out much more significant: the half-life for 1 μm particles with a removal high-pressure spray system is orders of magnitude shorter than that with a low-pressure spray system. The highest removal rate was

Experiments on aerosol removal by high-pressure water spray

International Nuclear Information System (INIS)

Corno, Ada del; Morandi, Sonia; Parozzi, Flavio; Araneo, Lucio; Casella, Francesco