High-power liquid-lithium jet target for neutron production

Science.gov (United States)

Halfon, S.; Arenshtam, A.; Kijel, D.; Paul, M.; Berkovits, D.; Eliyahu, I.; Feinberg, G.; Friedman, M.; Hazenshprung, N.; Mardor, I.; Nagler, A.; Shimel, G.; Tessler, M.; Silverman, I.

2013-12-01

A compact liquid-lithium target (LiLiT) was built and tested with a high-power electron gun at the Soreq Nuclear Research Center. The lithium target, to be bombarded by the high-intensity proton beam of the Soreq Applied Research Accelerator Facility (SARAF), will constitute an intense source of neutrons produced by the 7Li(p,n)7Be reaction for nuclear astrophysics research and as a pilot setup for accelerator-based Boron Neutron Capture Therapy. The liquid-lithium jet target acts both as neutron-producing target and beam dump by removing the beam thermal power (>5 kW, >1 MW/cm3) with fast transport. The target was designed based on a thermal model, accompanied by a detailed calculation of the 7Li(p,n) neutron yield, energy distribution, and angular distribution. Liquid lithium is circulated through the target loop at ˜200 °C and generates a stable 1.5 mm-thick film flowing at a velocity up to 7 m/s onto a concave supporting wall. Electron beam irradiation demonstrated that the liquid-lithium target can dissipate electron power areal densities of >4 kW/cm2 and volume power density of ˜2 MW/cm3 at a lithium flow of ˜4 m/s while maintaining stable temperature and vacuum conditions. The LiLiT setup is presently in online commissioning stage for high-intensity proton beam irradiation (1.91-2.5 MeV, 1-2 mA) at SARAF.

Target experiments with high-power proton beams

Energy Technology Data Exchange (ETDEWEB)

Baumung, K; Bluhm, H; Hoppe, P; Rusch, D; Singer, J; Stoltz, O [Forschungszentrum Karlsruhe (Germany); Kanel, G I; Razorenov, S V; Utkin, A V [Russian Academy of Sciences, Chernogolovka (Russian Federation). Inst. of Chemical Physics

1997-12-31

At the Karlsruhe Light Ion Facility KALE a pulsed high-power proton beam (50 ns, 0.15 TW/cm{sup 2}, 8 mm fwhm focus diameter, 1.7 MeV peak proton energy) is used to generate short, intense pressure pulses or to ablatively accelerate targets 10-100 {mu}m thick to velocities > 10 km/s. The velocity history of the rear target surface is recorded by line-imaging laser Doppler velocimetry with high spatial ({>=} 10 {mu}m) and temporal ({>=} 200 ps) resolution, and provides information on proton beam parameters, and on the state of the matter at high energy densities and intense loading. Utilizing the bell-shaped power density profile the authors demonstrated a new straightforward method for measuring the shock pressure that leads to material melting in the rarefaction wave. For the first time, the dynamic tensile strength was measured across a crystal grain boundary, and using targets with a 1D periodic structure, the growth rate of a Rayleigh Taylor instability could be measured for the first time in direct drive experiments with an ion beam. (author). 8 figs., 15 refs.

The 13th International Workshop on Targetry and Target Chemistry Proceedings

DEFF Research Database (Denmark)

Haroun, Samar; Givskov, Alex David; Jensen, Mikael

in situ target chemistry and the engineering required to optimize production yields. In the workshop, experience, ideas and information are freely and openly shared; learning and collaborations are fostered, with active participation by all attendees. This participation includes both formal and informal......This report contains the complete proceedings of the 13th International Workshop on Targetry and Target Chemistry. The Workshop was held at Risø National Laboratory for Sustainable Energy on July 26-28 2010. The workshop deals with the development of methods and systems for efficient production...... of the WTTC is to advance the science associated with radioisotope production targetry. The Workshops are designed to bring experienced targetry scientists together with newcomers to the field, both from industry and academia, to discuss issues of targetry and target chemistry and approaches to exploring...

Generic study on the design and operation of high power targets

Directory of Open Access Journals (Sweden)

A. Ahmad

2014-02-01

Full Text Available With the move towards beam power in the range of 1–10 MW, a thorough understanding of the response of target materials and auxiliary systems to high power densities and intense radiation fields is required. This paper provides insight into three major aspects related to the design and operation of high power solid targets: thermal stresses, coolant performance, and radiation damage. Where appropriate, a figure-of-merit approach is followed to facilitate the comparison between different target or coolant candidates. The section on radiation damage reports total and spatial variations of displacement-per-atom and helium production levels in different target materials.

16th International Workshop on Polarized Sources, Targets, and Polarimetry (PSTP 2015)

CERN Document Server

2015-01-01

The Workshop on Polarized Sources, Targets and Polarimetry has been a tradition for more than 20 years, moving between Europe, USA and Japan. The XVIth International Workshop on Polarized Sources, Targets and Polarimetry (PSTP 2015) will take place at the Ruhr-University of Bochum, Germany. The workshop addresses the physics and technological challenges related to polarized gas/solid targets, polarized electron/positron/ion/neutron sources, polarimetry and their applications. will be published in Proceedings of Science

The 13th international workshop on targetry and target chemistry proceedings

Energy Technology Data Exchange (ETDEWEB)

Haroun, S. (SFU, TRIUMF (Canada)); Givskov, A.; Jensen, Mikael (Technical Univ. of Denmark. Risoe National Laboratory for Sustainable Energy, Radiation Research Division, Roskilde (Denmark))

2011-06-15

This report contains the complete proceedings of the 13th International Workshop on Targetry and Target Chemistry. The Workshop was held at Risoe National Laboratory for Sustainable Energy on July 26-28 2010. The workshop deals with the development of methods and systems for efficient production of radioactive isotopes with accelerators. The WTTC series of workshops was initiated for the purpose of exchanging information about the problems and solutions associated with the production of radioisotopes for biomedical research and their applications to the diagnosis and treatment of disease. The goal of the WTTC is to advance the science associated with radioisotope production targetry. The Workshops are designed to bring experienced targetry scientists together with newcomers to the field, both from industry and academia, to discuss issues of targetry and target chemistry and approaches to exploring in situ target chemistry and the engineering required to optimize production yields. In the workshop, experience, ideas and information are freely and openly shared; learning and collaborations are fostered, with active participation by all attendees. This participation includes both formal and informal sessions. The present proceedings captures both submitted abstracts and the actual presentations showed during the very successful workshop meeting number 13 in the row, the WTTC13. (Author)

The 13th international workshop on targetry and target chemistry proceedings

International Nuclear Information System (INIS)

Haroun, S.; Givskov, A.; Jensen, Mikael

2011-06-01

This report contains the complete proceedings of the 13th International Workshop on Targetry and Target Chemistry. The Workshop was held at Risoe National Laboratory for Sustainable Energy on July 26-28 2010. The workshop deals with the development of methods and systems for efficient production of radioactive isotopes with accelerators. The WTTC series of workshops was initiated for the purpose of exchanging information about the problems and solutions associated with the production of radioisotopes for biomedical research and their applications to the diagnosis and treatment of disease. The goal of the WTTC is to advance the science associated with radioisotope production targetry. The Workshops are designed to bring experienced targetry scientists together with newcomers to the field, both from industry and academia, to discuss issues of targetry and target chemistry and approaches to exploring in situ target chemistry and the engineering required to optimize production yields. In the workshop, experience, ideas and information are freely and openly shared; learning and collaborations are fostered, with active participation by all attendees. This participation includes both formal and informal sessions. The present proceedings captures both submitted abstracts and the actual presentations showed during the very successful workshop meeting number 13 in the row, the WTTC13. (Author)

High-power liquid-lithium jet target for neutron production

OpenAIRE

Halfon, S.; Arenshtam, A.; Kijel, D.; Paul, M.; Berkovits, D.; Eliyahu, I.; Feinberg, G.; Friedman, M.; Hazenshprung, N.; Mardor, I.; Nagler, A.; Shimel, G.; Tessler, M.; Silverman, I.

2013-01-01

A compact Liquid-Lithium Target (LiLiT) was built and tested with a high-power electron gun at Soreq Nuclear Research Center. The lithium target, to be bombarded by the high-intensity proton beam of the Soreq Applied Research Accelerator Facility (SARAF), will constitute an intense source of neutrons produced by the 7Li(p,n)7Be reaction for nuclear astrophysics research and as a pilot setup for accelerator-based Boron Neutron Capture Therapy (BNCT). The liquid-lithium jet target acts both as ...

Development and delivery of a workshop methodology: planning for biomass power plant projects

Energy Technology Data Exchange (ETDEWEB)

Gray, A.J.; Delbridge, P.; Trevorrow, E.; Pile, C.

2001-07-01

This report gives details of the approach used to develop a workshop methodology to help planners and stakeholders address key issues that may arise when submitting a planning application for a biomass power plant in the light of the UK government's energy and climate change targets. The results of interviews with stakeholders (central government, regulatory authorities, developers, planners, non-governmental organisations, local community, resident groups) are summarised, and the NIMBY (not in my back yard) syndrome, the lack of trust in the developer, and lack of awareness of the use of biomass are discussed. Details are given of the design and testing of the workshop methodology and the resulting workshop methodology and workbook guide aimed at understanding the stakeholder issues and concerns through stakeholder discussions.

Test of a High Power Target Design

CERN Multimedia

2002-01-01

%IS343 :\\\\ \\\\ A high power tantalum disc-foil target (RIST) has been developed for the proposed radioactive beam facility, SIRIUS, at the Rutherford Appleton Laboratory. The yield and release characteristics of the RIST target design have been measured at ISOLDE. The results indicate that the yields are at least as good as the best ISOLDE roll-foil targets and that the release curves are significantly faster in most cases. Both targets use 20 -25 $\\mu$m thick foils, but in a different internal geometry.\\\\ \\\\Investigations have continued at ISOLDE with targets having different foil thickness and internal geometries in an attempt to understand the release mechanisms and in particular to maximise the yield of short lived isotopes. A theoretical model has been developed which fits the release curves and gives physical values of the diffusion constants.\\\\ \\\\The latest target is constructed from 2 $\\mu$m thick tantalum foils (mass only 10 mg) and shows very short release times. The yield of $^{11}$Li (half-life of ...

The SPES High Power ISOL production target

Science.gov (United States)

Andrighetto, A.; Corradetti, S.; Ballan, M.; Borgna, F.; Manzolaro, M.; Scarpa, D.; Monetti, A.; Rossignoli, M.; Silingardi, R.; Mozzi, A.; Vivian, G.; Boratto, E.; De Ruvo, L.; Sattin, N.; Meneghetti, G.; Oboe, R.; Guerzoni, M.; Margotti, A.; Ferrari, M.; Zenoni, A.; Prete, G.

2016-11-01

SPES (Selective Production of Exotic Species) is a facility under construction at INFN-LNL (Istituto Nazionale di Fisica Nucleare - Laboratori Nazionali di Legnaro), aimed to produce intense neutron-rich radioactive ion beams (RIBs). These will be obtained using the ISOL (Isotope Separation On-Line) method, bombarding a uranium carbide target with a proton beam of 40MeV energy and currents up to 200μA. The target configuration was designed to obtain a high number of fissions, up to 1013 per second, low power deposition and fast release of the produced isotopes. The exotic isotopes generated in the target are ionized, mass separated and re-accelerated by the ALPI superconducting LINAC at energies of 10AMeV and higher, for masses in the region of A = 130 amu , with an expected rate on the secondary target up to 109 particles per second. In this work, recent results on the R&D activities regarding the SPES RIB production target-ion source system are reported.

A 20 kw beam-on-target test of a high-power liquid lithium target for RIA

International Nuclear Information System (INIS)

Reed, Claude B.; Nolen, Jerry A.; Specht, James R.; Novick, Vincent J.; Plotkin, Perry

2004-01-01

The high-power heavy-ion beams produced by the Rare Isotope Accelerator (RIA) driver linac have large energy deposition density in solids and in many cases no solid materials would survive the full beam power. Liquid lithium technology has been proposed to solve this problem in RIA. Specifically, a windowless target for the production of radioactive ions via fragmentation, consisting of a jet of about 3 cm thickness of flowing liquid lithium, exposed to the beamline vacuum [1,2] is being developed. To demonstrate that power densities equivalent to a 200-kW RIA uranium beam, deposited in the first 4 mm of a flowing lithium jet, can be handled by the windowless target design, a high power 1 MeV Dynamitron was leased and a test stand prepared to demonstrate the target's capability of absorbing and carrying away a 20kW heat load without disrupting either the 5 mm x 10 mm flowing lithium jet target or the beam line vacuum

Workshop on power plant cable condition monitoring: Proceedings

International Nuclear Information System (INIS)

Del Valle, L.

1988-07-01

A three-day workshop on cable condition monitoring was held in San Francisco on Fegruary 16--18, 1988. The workshop was cosponsored by the Nuclear Power, Electrical Systems, and Coal Combustion Systems Divisions of the Electric Power Research Institute. The primary objective of the workshop was to identify the state-of-the-art for cable condition monitoring. Twenty-five technical papers as well as EPRI research programs were presented at the technical sessions. Four working group sessions and one general session were held on each of two days. Each group session provided a forum for participants to exchange ideas and to discuss in more depth research for cable condition monitoring, existing and innovative testing technology, and utility and NRC needs for testing. Recommendations from the working groups were summarized and presented at the end of the workshop

Proceedings: Power Plant Electric Auxiliary Systems Workshop

International Nuclear Information System (INIS)

1992-06-01

The EPRI Power Plant Electric Auxiliary Systems Workshop, held April 24--25, 1991, in Princeton, New Jersey, brought together utilities, architect/engineers, and equipment suppliers to discuss common problems with power plant auxiliary systems. Workshop participants presented papers on monitoring, identifying, and solving problems with auxiliary systems. Panel discussions focused on improving systems and existing and future plants. The solutions presented to common auxiliary system problems focused on practical ideas that can enhance plant availability, reduce maintenance costs, and simplify the engineering process. The 13 papers in these proceedings include: Tutorials on auxiliary electrical systems and motors; descriptions of evaluations, software development, and new technologies used recently by electric utilities; an analysis of historical performance losses caused by power plant auxiliary systems; innovative design concepts for improving auxiliary system performance in future power plants

Shielding Aspects of Accelerators, Targets and Irradiation Facilities - SATIF-11 Workshop Proceedings Report

International Nuclear Information System (INIS)

2013-01-01

Particle accelerators have evolved over the last decades from simple devices to powerful machines. In recent years, new technological and research applications have helped to define requirements while the number of accelerator facilities in operation, being commissioned, designed or planned has grown significantly. Their parameters, which include the beam energy, currents and intensities, and target composition, can vary widely, giving rise to new radiation shielding issues and challenges. Particle accelerators must be operated in safe ways to protect operators, the public and the environment. As the design and use of these facilities evolve, so must the analytical methods used in the safety analyses. These workshop proceedings review the state of the art in radiation shielding of accelerator facilities and irradiation targets. They also evaluate progress in the development of modelling methods used to assess the effectiveness of such shielding as part of safety analyses. The transport of radiation through shielding materials is a major consideration in the safety design studies of nuclear power plants, and the modelling techniques used may be applied to many other types of scientific and technological facilities. Accelerator and irradiation facilities represent a key capability in R and D, medical and industrial infrastructures, and they can be used in a wide range of scientific, medical and industrial applications. High-energy ion accelerators, for example, are now used not only in fundamental research, such as the search for new super-heavy nuclei, but also for therapy as part of cancer treatment. While the energy of the incident particles on the shielding of these facilities may be much higher than those found in nuclear power plants, much of the physics associated with the behaviour of the secondary particles produced is similar, as are the computer modelling techniques used to quantify key safety design parameters, such as radiation dose and activation levels

Proceedings of the second workshop on polarised target materials

International Nuclear Information System (INIS)

Court, G.R.; Niinikoski, T.O.; Cox, S.F.J.; Cragg, D.A.

1980-10-01

The proceedings are reported of a second international workshop which was convened to consider the use of polarised targets in nuclear research and in particular the experimental difficulties imposed by the limitations of target materials with respect to their relatively low hydrogen content and susceptibility to radiation damage. Papers presented were entitled: (1) Introduction and general review. (2) Theory of dynamic nuclear polarisation. (3) Radiation induced paramagnetic centres in organic and inorganic materials. (4) Dynamic nuclear polarisation with radiation induced free radicals. (5) Radiation damage of chemically doped materials. (6) Chemical doping. (7) Techniques and instrumentation. (8) The use of polarised nuclei in physics with neutrons. (9) The use of polarised targets in high energy physics. (U.K.)

EDITORIAL: The Fourth International Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2004)

Science.gov (United States)

Tanaka, Shuji; Toriyama, Toshiyuki

2005-09-01

This special issue of the Journal of Micromechanics and Microengineering features papers selected from the Fourth International Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2004). The workshop was held in Kyoto, Japan, on 28-30 November 2004, by The Ritsumeikan Research Institute of Micro System Technology in cooperation with The Global Emerging Technology Institute, The Institute of Electrical Engineers of Japan, The Sensors and Micromachines Society, The Micromachine Center and The Kyoto Nanotech Cluster. Power MEMS is one of the newest categories of MEMS, which encompasses microdevices and microsystems for power generation, energy conversion and propulsion. The first concept of power MEMS was proposed in the late 1990s by Epstein's group at the Massachusetts Institute of Technology, where they continue to study MEMS-based gas turbine generators. Since then, the research and development of power MEMS have been promoted by the need for compact power sources with high energy and power density. Since its inception, power MEMS has expanded to include not only various MEMS-based power generators but also small energy machines and microdevices for macro power generators. At the last workshop, various devices and systems, such as portable fuel cells and their peripherals, micro and small turbo machinery, energy harvesting microdevices, and microthrusters, were presented. Their power levels vary from ten nanowatts to hundreds of watts, spanning ten orders of magnitude. The first PowerMEMS workshop was held in 2000 in Sendai, Japan, and consisted of only seven invited presentations. The workshop has grown since then, and in 2004 there were 5 invited, 20 oral and 29 poster presentations. From the 54 papers in the proceedings, 12 papers have been selected for this special issue. I would like to express my appreciation to the members of the Organizing Committee and Technical Program Committee. This special issue was

Liquid metal targets for high-power applications : pulsed heating and shock hydrodynamics

International Nuclear Information System (INIS)

Hassanein, A.

2000-01-01

Significant interest has recently focused on the use of liquid-metal targets flowing with high velocities for various high-power nuclear and high-energy physics applications such as fusion reactor first-walls, the Spallation Neutron Source, Isotope Separation On Line, and Muon Collider projects. This is because the heat generated in solid targets due to beam or plasma bombardment cannot be removed easily and the resulting thermal shock damage could be a serious lifetime problem for long-term operation. More recently, the use of free or open flying-liquid jets has been proposed for higher-power-density applications. The behavior of a free-moving liquid mercury or gallium jet subjected to proton beam deposition in a strong magnetic field has been modeled and analyzed for the Muon Collider project. Free-liquid-metal jets can offer significant advantages over conventional solid targets, particularly for the more demanding and challenging high-power applications. However, the use of free-moving liquid-metal targets raises a number of new and challenging problems such as instabilities of the jet in a strong magnetic field, induced eddy-current effects on jet shape, thermal-shock formation, and possible jet fragmentation. Problems associated with shock heating of liquid jets in a strong magnetic field are analyzed in this study

PST 2009: XIII International Workshop on Polarized Sources Targets and Polarimetry

Science.gov (United States)

Lenisa, Paolo

2011-05-01

The workshops on polarized sources, targets, and polarimetry are held every two years. In 2009 the meeting took place in Ferrara, Italy, and was organized by the University of Ferrara and INFN. Sessions on Polarized Proton and Deuterium Sources, Polarized Electron Sources, Polarimetry, Polarized Solid Targets, and Polarized Internal Targets, highlighted topics, recent developments, and progress in the field. A session dedicated to Future Facilities provided an overview of a number of new activities in the spin-physics sector at facilities that are currently in the planning stage. Besides presenting a broad overview of polarized ion sources, electron sources, solid and gaseous targets, and their neighbouring fields, the workshop also addressed the application of polarized atoms in applied sciences and medicine that is becoming increasingly important.

Predicting the Noise of High Power Fluid Targets Using Computational Fluid Dynamics

Science.gov (United States)

Moore, Michael; Covrig Dusa, Silviu

The 2.5 kW liquid hydrogen (LH2) target used in the Qweak parity violation experiment is the highest power LH2 target in the world and the first to be designed with Computational Fluid Dynamics (CFD) at Jefferson Lab. The Qweak experiment determined the weak charge of the proton by measuring the parity-violating elastic scattering asymmetry of longitudinally polarized electrons from unpolarized liquid hydrogen at small momentum transfer (Q2 = 0 . 025 GeV2). This target satisfied the design goals of bench-marked with the Qweak target data. This work is an essential component in future designs of very high power low noise targets like MOLLER (5 kW, target noise asymmetry contribution < 25 ppm) and MESA (4.5 kW).

HG2006 Workshop on High-Gradient Radio Frequency

CERN Multimedia

2006-01-01

Meeting to be held at CERN on 25-27 September 2006 in Room 40/S2-B01 (Building 40). The objective of the workshop is to bring the high-gradient RF community together to present and discuss recent theoretical and experimental developments. Significant progress has recently been made in understanding the basic physics of rf breakdown and developing techniques for achieving higher gradients. This workshop should contribute to maintaining these efforts and to promoting contacts and collaboration. The scientific programme will be organized in half day sessions dedicated to: High-gradient rf experimental results Theory and computation High-gradient technology, materials and processing Specialized experiments on related high-gradient or high-power phenomenon like dc discharge and pulsed surface heating Reports from collaborations and projects. Each session will consist of selected presentations followed by a dedicated discussion. Information about the meeting and participant registration is available at http...

Evaluation of the Geothermal Public Power Utility Workshops in California

Energy Technology Data Exchange (ETDEWEB)

Farhar, B. C.

2004-10-01

The federal government devotes significant resources to educating consumers and businesses about geothermal energy. Yet little evidence exists for defining the kinds of information needed by the various audiences with specialized needs. This paper presents the results of an evaluation of the Geothermal Municipal Utility Workshops that presented information on geothermal energy to utility resource planners at customer-owned utilities in California. The workshops were sponsored by the Western Area Power Administration and the U.S. Department of Energy's GeoPowering the West Program and were intended to qualitatively assess the information needs of municipal utilities relative to geothermal energy and get feedback for future workshops. The utility workshop participants found the geothermal workshops to be useful and effective for their purposes. An important insight from the workshops is that utilities need considerable lead-time to plan a geothermal project. They need to know whether it is better to own a project or to purchase geothermal electricity from another nonutility owner. California customer-owned utilities say they do not need to generate more electricity to meet demand, but they do need to provide more electricity from renewable resources to meet the requirements of the state's Renewable Portfolio Standard.

Proceedings of the Fifth International Workshop on Targetry and Target Chemistry

International Nuclear Information System (INIS)

Dahl, J.R.; Ferrieri, R.; Finn, R.; Schlyer, D.J.

1994-01-01

The goal of the International Workshop on Targetry and Target Chemistry series has always been to provide an open forum for discussion of medical radionuclide production, primarily with particle accelerators. The format is intended to encourage the participants to set the direction of the ensuing discussion, allowing the participants to focus on areas of greatest immediate interest. The preceding workshops have set this tone and this workshop was designed to continue in this spirit. The topics of each session were selected by the local organizing committee after discussion with many of the attendees of the previous workshops. The formality of the workshops has gradually increased from the first rather small, very informal gathering in Heidelburg to the larger contingent present in Villigen, but the open discussion of topics of preoccupation has been maintained. Each Workshop has had areas of particular fascination. In the Fifth workshop the major focus was on the development of new accelerators and on the production of ammonia. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database

Proceedings of the Fifth International Workshop on Targetry and Target Chemistry

Energy Technology Data Exchange (ETDEWEB)

Dahl, J.R.; Ferrieri, R.; Finn, R.; Schlyer, D.J. [eds.

1994-12-31

The goal of the International Workshop on Targetry and Target Chemistry series has always been to provide an open forum for discussion of medical radionuclide production, primarily with particle accelerators. The format is intended to encourage the participants to set the direction of the ensuing discussion, allowing the participants to focus on areas of greatest immediate interest. The preceding workshops have set this tone and this workshop was designed to continue in this spirit. The topics of each session were selected by the local organizing committee after discussion with many of the attendees of the previous workshops. The formality of the workshops has gradually increased from the first rather small, very informal gathering in Heidelburg to the larger contingent present in Villigen, but the open discussion of topics of preoccupation has been maintained. Each Workshop has had areas of particular fascination. In the Fifth workshop the major focus was on the development of new accelerators and on the production of ammonia. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

Summary of the XIII International Workshop on Polarized Sources, Targets and Polarimetry

Science.gov (United States)

Rathmann, F.

2011-01-01

The workshops on polarized sources, targets, and polarimetry are held every two years. The present meeting took place in Ferrara, Italy, and was organized by the University of Ferrara. Sessions on Polarized Proton and Deuterium Sources, Polarized Electron Sources, Polarimetry, Polarized Solid Targets, and Polarized Internal Targets, highlighted topics, recent developments, and progress in the field. A session decicated to Future Facilities provided an overview of a number of new activities in the spin-physics sector at facilities that are currently in the planning stage. Besides presenting a broad overview of polarized ion sources, electron sources, solid and gaseous targets, and their neighboring fields, the workshop also addressed the application of polarized atoms in applied sciences and medicine that is becoming increasingly important.

A high-power target experiment

CERN Document Server

Kirk, H G; Ludewig, H; Palmer, Robert; Samulyak, V; Simos, N; Tsang, Thomas; Bradshaw, T W; Drumm, Paul V; Edgecock, T R; Ivanyushenkov, Yury; Bennett, Roger; Efthymiopoulos, Ilias; Fabich, Adrian; Haseroth, H; Haug, F; Lettry, Jacques; Hayato, Y; Yoshimura, Koji; Gabriel, Tony A; Graves, Van; Spampinato, P; Haines, John; McDonald, Kirk T

2005-01-01

We describe an experiment designed as a proof-of-principle test for a target system capable of converting a 4 MW proton beam into a high-intensity muon beam suitable for incorporation into either a neutrino factory complex or a muon collider. The target system is based on exposing a free mercury jet to an intense proton beam in the presence of a high strength solenoidal field.

Workshop: Research and development plans for high power spallation neutron testing at BNL

International Nuclear Information System (INIS)

1996-01-01

This report consists of vugraphs from presentations at the meeting. The papers covered the following topics: (1) APS as a proton source; (2) target status for NSNS (National Spallation Neutron Source); (3) spallation neutron source in Japan; (4) liquid LiBi flow loop; and (5) research and development plans for high power tests at the AGS

Second ANS workshop on the safety of Soviet-designed nuclear power plants. Summary report

International Nuclear Information System (INIS)

Bari, R.A.

1995-03-01

The Second American Nuclear Society Workshop on the Safety of Soviet-Designed Nuclear Power Plants was held in Washington, DC, in November, 1994. The Workshop consisted of both plenary sessions and working sessions with three hundred participants overall. All countries with operating Soviet-Designed nuclear power plants were represented and representatives from several other countries also participated. In addition to the status and plans related to technical issues, the Workshop also included discussions of economic, political, legal, and social issues as they relate to the safety of these nuclear power plants

Proceedings of the international workshop on the technology and thermal hydraulics of heavy liquid metals (Hg, Pb, Bi, and their eutectics)

International Nuclear Information System (INIS)

Appleton, B.R.; Bauer, G.S.

1996-06-01

The International Workshop on the Technology and Thermal Hydraulics of Heavy Liquid Metals (Schruns Workshop) was organized to assess the R ampersand D and technology problems associated with designing and building a heavy liquid metal target for a spallation neutron source. The European scientific community is completing a feasibility study for a future, accelerator-based, pulsed spallation neutron source that would deliver a beam power of 5 megawatts (MW) to a target. They have concluded that a liquid metal target is preferable to conventional solid targets for handling the extreme radiation environments, high heat loads, and pulsed power. Similarly, the ORNL has been funded by the DOE to design a high-power, pulsed spallation neutron source that would begin operation at about 1 MW but that could be upgraded to significantly higher powers in the future. Again, the most feasible target design appears to be a liquid metal target. Since the expertise needed to consider these problems resides in a number of disparate disciplines not normally covered by existing conferences, this workshop was organized to bring a small number of scientists and engineers together to assess the opportunities for building such a target. The objectives and goals of the Schruns Workshop were to: review and share existing information on the science and technology of heavy liquid metal systems. Evaluate the opportunities and limitations of materials compatibility, thermal hydraulics and heat transfer, chemical reactions, corrosion, radiation effects, liquid-gas mixtures, systems designs, and circuit components for a heavy liquid metal target. Establish the critical R ampersand D and technology that is necessary to construct a liquid metal target. Explore opportunities for cooperative R ampersand D among members of the international community that could expedite results, and share expertise and resources. Selected papers are indexed separately for inclusion in the Energy Science and

Proceedings of the international workshop on the technology and thermal hydraulics of heavy liquid metals (Hg, Pb, Bi, and their eutectics)

Energy Technology Data Exchange (ETDEWEB)

Appleton, B.R.; Bauer, G.S. [comp.

1996-06-01

The International Workshop on the Technology and Thermal Hydraulics of Heavy Liquid Metals (Schruns Workshop) was organized to assess the R&D and technology problems associated with designing and building a heavy liquid metal target for a spallation neutron source. The European scientific community is completing a feasibility study for a future, accelerator-based, pulsed spallation neutron source that would deliver a beam power of 5 megawatts (MW) to a target. They have concluded that a liquid metal target is preferable to conventional solid targets for handling the extreme radiation environments, high heat loads, and pulsed power. Similarly, the ORNL has been funded by the DOE to design a high-power, pulsed spallation neutron source that would begin operation at about 1 MW but that could be upgraded to significantly higher powers in the future. Again, the most feasible target design appears to be a liquid metal target. Since the expertise needed to consider these problems resides in a number of disparate disciplines not normally covered by existing conferences, this workshop was organized to bring a small number of scientists and engineers together to assess the opportunities for building such a target. The objectives and goals of the Schruns Workshop were to: review and share existing information on the science and technology of heavy liquid metal systems. Evaluate the opportunities and limitations of materials compatibility, thermal hydraulics and heat transfer, chemical reactions, corrosion, radiation effects, liquid-gas mixtures, systems designs, and circuit components for a heavy liquid metal target. Establish the critical R & D and technology that is necessary to construct a liquid metal target. Explore opportunities for cooperative R & D among members of the international community that could expedite results, and share expertise and resources. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

Uniform irradiation of adjustable target spots in high-power laser driver

International Nuclear Information System (INIS)

Jiang Xiujuan; Li Jinghui; Li Huagang; Li Yang; Lin Zunqi

2011-01-01

For smoothing and shaping the on-target laser patterns flexibly in high-power laser drivers, a scheme has been developed that includes a zoom lens array and two-dimensional smoothing by spectral dispersion (SSD). The size of the target pattern can be controlled handily by adjusting the focal length of the zoom lens array, while the profile of the pattern can be shaped by fine tuning the distance between the target and the focal plane of the principal focusing lens. High-frequency stripes inside the pattern caused by beamlet interference are wiped off by spectral dispersion. Detailed simulations indicate that SSD works somewhat differently for spots of different sizes. For small spots, SSD mainly smooths the intensity modulation of low-to-middle spatial frequency, while for large spots, SSD sweeps the fine speckle structure to reduce nonuniformity of middle-to-high frequency. Spatial spectra of the target patterns are given and their uniformity is evaluated.

EDITORIAL: Selected papers from the 11th International Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2011) Selected papers from the 11th International Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2011)

Science.gov (United States)

Cho, Young-Ho

2012-09-01

This special section of Journal of Micromechanics and Microengineering features papers selected from the 11th International Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2011), held at Sejong Hotel in Seoul, Korea during 15-18 November 2011. Since the first PowerMEMS workshop held in Sendai, Japan in 2000, the workshop has developed as the premier forum for reporting research results in micro and nanotechnology for power generation, energy conversion, harvesting and processing applications, including in-depth technical issues on nanostructures and materials for small-scale high-density energy and thermal management. Potential PowerMEMS applications cover not only portable power devices for consumer electronics and remote sensors, but also micro engines, impulsive thrusters and fuel cells for systems ranging from the nanometer to the millimeter scale. The 2011 technical program consists of 1 plenary talk, 4 invited talks and 118 contributed presentations. The 48 oral and 70 poster presentations, selected by 27 Technical Program Committee Members from 131 submitted abstracts, have stimulated lively discussion maximizing the interaction between participants. Among them, this special section includes 9 papers covering micro-scale power generators, energy converters, harvesters, thrusters and thermal coolers. Finally, we are grateful to the members of the International Steering Committee, the Technical Program Committee, and the Local Organizing Committee for their efforts and contributions to PowerMEMS 2011. We also thank the two companies Samsung Electro-Mechanics and LG Elite for technical tour arrangements. Special thanks go to Dr Ian Forbes, the editorial staff of the Journal of Micromechanics and Microengineering, as well as to the staff of IOP Publishing for making this special section possible.

MO-AB-210-03: Workshop [Advancements in high intensity focused ultrasound

Energy Technology Data Exchange (ETDEWEB)

Lu, Z. [University of Chicago (United States)

2015-06-15

The goal of this ultrasound hands-on workshop is to demonstrate advancements in high intensity focused ultrasound (HIFU) and to demonstrate quality control (QC) testing in diagnostic ultrasound. HIFU is a therapeutic modality that uses ultrasound waves as carriers of energy. HIFU is used to focus a beam of ultrasound energy into a small volume at specific target locations within the body. The focused beam causes localized high temperatures and produces a well-defined regions of necrosis. This completely non-invasive technology has great potential for tumor ablation and targeted drug delivery. At the workshop, attendees will see configurations, applications, and hands-on demonstrations with on-site instructors at separate stations. The involvement of medical physicists in diagnostic ultrasound imaging service is increasing due to QC and accreditation requirements. At the workshop, an array of ultrasound testing phantoms and ultrasound scanners will be provided for attendees to learn diagnostic ultrasound QC in a hands-on environment with live demonstrations of the techniques. Target audience: Medical physicists and other medical professionals in diagnostic imaging and radiation oncology with interest in high-intensity focused ultrasound and in diagnostic ultrasound QC. Learning Objectives: Learn ultrasound physics and safety for HIFU applications through live demonstrations Get an overview of the state-of-the art in HIFU technologies and equipment Gain familiarity with common elements of a quality control program for diagnostic ultrasound imaging Identify QC tools available for testing diagnostic ultrasound systems and learn how to use these tools List of supporting vendors for HIFU and diagnostic ultrasound QC hands-on workshop: Philips Healthcare Alpinion Medical Systems Verasonics, Inc Zonare Medical Systems, Inc Computerized Imaging Reference Systems (CIRS), Inc. GAMMEX, Inc., Cablon Medical BV Steffen Sammet: NIH/NCI grant 5R25CA132822, NIH/NINDS grant 5R25NS

EDITORIAL: The 7th International Workshop on Micro and Nanotechnologies for Power Generation and Energy Conversion Applications (PowerMEMS 2007)

Science.gov (United States)

Hebling, C.; Woias, P.

2008-10-01

field trying to commercialize micro energy harvesting devices, micro thermo-photovoltaics or micro fuel cells in order to make an impact on our daily life. It is interesting to see the remarkable scientific dynamics and innovations in micro energy technology that have been mirrored in the scope of consecutive PowerMEMS workshops. Micro fuel cells, micro combustion systems and heat engines have been on-going topics from the beginning due to their promising power densities and high power levels up to hundreds of watts. At the other end of the power scale micro energy harvesting has entered the stage, with a remarkable growth rate of presentations during the last three workshops, towering over all other topics with 33 presentations at PowerMEMS 2007. Another significant trend is the slow but steady emergence of electronic energy management as a future key technology. As Guest Editors of this special issue we would like to express our appreciation to the members of the Organizing Committee and the Technical Program Committee of PowerMEMS for their on-going efforts. By selecting the research fields mentioned above they formed the PowerMEMS 2007 program as a comprehensive digest of today's micro energy technology that is reflected, along with selected high quality publications, in this special issue of JMM. We hope that this work will stimulate further innovative research in micro energy technology and will help to mark the trail for further progress in this exciting field of MEMS science and technology.

What future for nuclear power? Workshop report

International Nuclear Information System (INIS)

1998-01-01

A Workshop on this highly controversial subject, organized by the Energy and Environment Programme of the RIIA, was held on 10th November 1997 at Green College, Oxford. The meeting was attended by some forty people from eight countries, coming from the nuclear and electricity generating industry, governments, research organizations, academic institutions, environmental pressure groups and inter-governmental organizations. In addition, subsequent to this Workshop, there have been a number of smaller, more informal discussions on various aspects of the subject. This paper summarizes the main conclusions arising from the Workshop and from these later discussions

Advanced Power Electronics Interfaces for Distributed Energy Workshop Summary: August 24, 2006, Sacramento, California

Energy Technology Data Exchange (ETDEWEB)

Treanton, B.; Palomo, J.; Kroposki, B.; Thomas, H.

2006-10-01

The Advanced Power Electronics Interfaces for Distributed Energy Workshop, sponsored by the California Energy Commission Public Interest Energy Research program and organized by the National Renewable Energy Laboratory, was held Aug. 24, 2006, in Sacramento, Calif. The workshop provided a forum for industry stakeholders to share their knowledge and experience about technologies, manufacturing approaches, markets, and issues in power electronics for a range of distributed energy resources. It focused on the development of advanced power electronic interfaces for distributed energy applications and included discussions of modular power electronics, component manufacturing, and power electronic applications.

Summary of workshop on materials issues in low emission boilers and high efficiency coal-fired cycles

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

The purpose of the workshop was to review with experts in the field the materials issues associated with two of the primary coal power systems being developed by the DOE Office of Fossil Energy. The DOE-FE Advanced Power Systems Program includes natural gas-based and coal-based power systems. Major activities in the natural gas-based power systems area include the Advanced Turbine Systems (ATS) Program, the Fuel Cells Program, and Hybrid Cycles. The coal-based power systems projects include the Low Emissions Boiler Systems (LEBS) Program, the High-Performance Power Systems Program (HIPPS), the Integrated (Coal) Gasification Combined-Cycle Program, and the Fluidized-Bed Combustion Program. This workshop focused on the materials issues associated with the LEBS and HIPPS technologies.

High Power Proton Beam Shocks and Magnetohydrodynamics in a Mercury Jet Target for a Neutrino Factory

CERN Document Server

Fabich, A; Fabjan, Christian

2002-01-01

The feasibility of liquid metal jet targets for secondary particle production with high power proton beams has been studied. The main aspects of the thesis were benchmark experiments covering the behaviour of liquid targets under thermal shock waves induced by high power proton beams, and also magnetohydrodynamic effects. Severe challenges were imposed by safety issues and the restricted beam time to the tests in ISOLDE at CERN and at the High Magnetic Field Laboratory at Grenoble. Restricted access times in high radiation level areas were of the order of minutes and in this short time span, the complete experimental setup had to be performed and verified. The involvement of mercury as liquid target material and its activation during beam tests demanded special confinement precautions. The setup for both experiments was based on the use of a high speed camera system for observation of the mercury target. The presence of high radiation or high magnetic field required the installation of the sensitive camera sy...

Proceedings of Wireless Technology in the Electric Power Industry Workshop

International Nuclear Information System (INIS)

2001-01-01

A one-day workshop was conducted at EPRI Charlotte to identify technology issues related to wireless technology in nuclear power plants. The meeting concluded with a roundtable discussion to determine what projects could be conducted to address opportunities and gaps in this technology; the three projects recommended for further investigation were a risk analysis, development of a technology strategy, and development of guidelines for reliable implementation of wireless technologies. The Proceedings CD includes workshop presentations in PowerPoint format. The presentations cover the following topics: (1) Wireless Project at TXU: Integration of Voice, Data, and Video; (2) Radio Upgrade Project at Public Service Electric and Gas Company (PSE and G) of New Jersey; and (3) Operational Experience with Wireless Communication at Nuclear Plants

Explosive vaporization induced by high-power CO2-laser target interactions

International Nuclear Information System (INIS)

Hugenschmidt, M.; Vollrath, K.

1976-01-01

The interactions of high-power laser pulses with targets such as metals or dielectric materials causes a series of optical, thermal, and mechanical processes. Thereby, heating, melting, and vaporization can take place in a short time. At power densities of about 10 7 to several 10 8 W/cm 2 this can even be produced explosively. As compared to continuous ablation, this type of interaction can remove greater masses from the bulk of material. The investigations are performed by using an electron-beam preionized CO 2 -laser acting on different target materials. The energy of the laser pulses is about 30 J, the pulse-half-widths of the long-tail pulses 4 to 6 μs. Optical measurements yield some information on threshold values for these processes, for the formation and expansion of plasmas, and for the ejection of material in form of greater particles. High speed photographic techniques include a rotating mirror- and an image converter camera. Starting from shock-wave theory, gas dynamic equations (in unidimensional approximation) allow for a quantitative determination of the specific internal energies and pressures in the case of optical detonation. (orig.) [de

3D numerical thermal stress analysis of the high power target for the SLC Positron Source

International Nuclear Information System (INIS)

Reuter, E.M.; Hodgson, J.A.

1991-05-01

The volumetrically nonuniform power deposition of the incident 33 GeV electron beam in the SLC Positron Source Target is hypothesized to be the most likely cause target failure. The resultant pulsed temperature distributions are known to generate complicated stress fields with no known closed-form analytical solution. 3D finite element analyses of these temperature distributions and associated thermal stress fields in the new High Power Target are described here. Operational guidelines based on the results of these analyses combined with assumptions made about the fatigue characteristics of the exotic target material are proposed. 6 refs., 4 figs

Reclaiming Power in the Writers' Workshop: Defending Curricula, Countering Narratives, and Changing Identities in Prekindergarten Classrooms

Science.gov (United States)

Kissel, Brian T.; Miller, Erin T.

2015-01-01

In this article, we examine how young writers and their teachers transformed the language arts curriculum by asserting their power within a familiar framework--the writer's workshop. We present three narratives in which multiple pre-kindergarten agents (students, teachers, and administrators) used their power within the Writer's Workshop to a)…

Photovoltaic rural electrification and the electric power utility. Workshop. [Selected Papers

Energy Technology Data Exchange (ETDEWEB)

Huacuz, J. M.; Villasenor, F.; Urrutia, M. [eds.] [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1995-12-31

This document contains the national and international programs about photovoltaic systems for rural electrification and the electric power utility experiences about PV programs. The IERE Workshop was hold from May 8 to 12, 1995 in Cocoyoc, Mexico. It was organized by the Electrical Research Institute of Mexico (Instituto de Investigaciones Electricas (IIE)) and the U.S. Electric Power Research Institute (EPRI). The Workshop was attended by 38 delegates from 13 countries [Espanol] Este documento contiene los programas nacionales e internacionales sobre electrificacion fotovoltaica rural y las experiencias en programas fotovoltaicos de empresas electricas. El taller de trabajo IERE fue realizado los dias del 8 al 12 de mayo de 1995 en Cocoyoc, Mexico. Fue organizado por el Instituto de Investigaciones Electricas (IIE) y el U.S. Electric Power Research Institute (EPRI) (Instituto de Investigaciones de Energia Electrica de Estados Unidos). A este taller de trabajo asistieron 38 delegados de 13 paises

Photovoltaic rural electrification and the electric power utility. Workshop. [Selected Papers

Energy Technology Data Exchange (ETDEWEB)

Huacuz, J M; Villasenor, F; Urrutia, M [eds.; Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1996-12-31

This document contains the national and international programs about photovoltaic systems for rural electrification and the electric power utility experiences about PV programs. The IERE Workshop was hold from May 8 to 12, 1995 in Cocoyoc, Mexico. It was organized by the Electrical Research Institute of Mexico (Instituto de Investigaciones Electricas (IIE)) and the U.S. Electric Power Research Institute (EPRI). The Workshop was attended by 38 delegates from 13 countries [Espanol] Este documento contiene los programas nacionales e internacionales sobre electrificacion fotovoltaica rural y las experiencias en programas fotovoltaicos de empresas electricas. El taller de trabajo IERE fue realizado los dias del 8 al 12 de mayo de 1995 en Cocoyoc, Mexico. Fue organizado por el Instituto de Investigaciones Electricas (IIE) y el U.S. Electric Power Research Institute (EPRI) (Instituto de Investigaciones de Energia Electrica de Estados Unidos). A este taller de trabajo asistieron 38 delegados de 13 paises

Time Structure of Particle Production in the Merit High-Power Target Experiment

CERN Document Server

Efthymiopoulos, I; Palm, M; Lettry, J; Haug, F; Pereira, H; Pernegger, H; Steerenberg, R; Grudiev, A; Kirk, H G; Park, H; Tsang, T; Mokhov, N; Striganov, S; Carroll, A J; Graves, V B; Spampinato, P T; McDonald, K T; Bennett, J R J; Caretta, O; Loveridge, P

2010-01-01

The MERIT experiment is a proof-of-principle test of a target system for high power proton beam to be used as front-end for a neutrino factory complex or amuon collider. The experiment took data in autumn 2007 with the fast extracted beam from the CERN Proton Synchrotron (PS) to a maximum intensity of about 30 × 1012 protons per pulse. We report results from the portion of the MERIT experiment in which separated beam pulses were delivered to a free mercury jet target with time intervals between pulses varying from 2 to 700 μs. The analysis is based on the responses of particle detectors placed along side and downstream of the target.

High heat flux cooling for accelerator targets

International Nuclear Information System (INIS)

Silverman, I.; Nagler, A.

2002-01-01

Accelerator targets, both for radioisotope production and for high neutron flux sources generate very high thermal power in the target material which absorbs the particles beam. Generally, the geometric size of the targets is very small and the power density is high. The design of these targets requires dealing with very high heat fluxes and very efficient heat removal techniques in order to preserve the integrity of the target. Normal heat fluxes from these targets are in the order of 1 kw/cm 2 and may reach levels of an order of magnitude higher

Target development for the SINQ high-power neutron spallation source

International Nuclear Information System (INIS)

Wagner, Werner

2002-01-01

SINQ is a 1 MW class research spallation neutron source, driven by the PSI proton accelerator system. In terms of beam power, it is, by a large margin, the most powerful spallation neutron source currently in operation worldwide. As a consequence, target load levels prevail in SINQ which are beyond the realm of existing experience. Therefore, an extensive materials irradiation program (STIP) is currently underway which will help to select the proper structural material and make dependable life time estimates accounting for the real operating conditions that prevail in the facility. In parallel, both theoretical and experimental work is going on within the MEGAPIE (MEGAwatt Pilot Experiment) project, to develop a liquid lead-bismuth spallation target for a beam power level of 1MW

High Field Workshop

Energy Technology Data Exchange (ETDEWEB)

Anon.

1984-12-15

A Workshop was held in Frascati at the end of September under the title 'Generation of High Fields for Particle Acceleration to Very High Energies'. It was organized by the CERN Accelerator School, the European Committee for Future Accelerators (ECFA) and the Italian INFN and was a further stage in the exploratory moves towards new techniques of acceleration. Such techniques might become necessary to respond to the needs of high energy physics some decades from now when the application of conventional techniques will probably have reached their limits.

Advanced targeted monitoring of high temperature components in power plants

Energy Technology Data Exchange (ETDEWEB)

Roos, E; Maile, K; Jovanovic, A [MPA Stuttgart (Germany)

1999-12-31

The article presents the idea of targeted monitoring of high-temperature pressurized components in fossil-fueled power plants, implemented within a modular software system and using, in addition to pressure and temperature data, also displacement and strain measurement data. The concept has been implemented as a part of a more complex company-oriented Internet/Intranet system of MPA Stuttgart (ALIAS). ALIAS enables to combine smoothly the monitoring results with those of the off-line analysis, e. g. sensitivity analyses, comparison with preceding experience (case studies), literature search, search in material databases -(experimental and standard data), nonlinear FE-analysis, etc. The concept and the system have been implemented in real plant conditions several power plants in Germany and Europe: one of these applications and its results are described more in detail in the presentation. (orig.) 9 refs.

Advanced targeted monitoring of high temperature components in power plants

Energy Technology Data Exchange (ETDEWEB)

Roos, E.; Maile, K.; Jovanovic, A. [MPA Stuttgart (Germany)

1998-12-31

The article presents the idea of targeted monitoring of high-temperature pressurized components in fossil-fueled power plants, implemented within a modular software system and using, in addition to pressure and temperature data, also displacement and strain measurement data. The concept has been implemented as a part of a more complex company-oriented Internet/Intranet system of MPA Stuttgart (ALIAS). ALIAS enables to combine smoothly the monitoring results with those of the off-line analysis, e. g. sensitivity analyses, comparison with preceding experience (case studies), literature search, search in material databases -(experimental and standard data), nonlinear FE-analysis, etc. The concept and the system have been implemented in real plant conditions several power plants in Germany and Europe: one of these applications and its results are described more in detail in the presentation. (orig.) 9 refs.

Environmental aspects of PV power systems. Report on the IEA PVPS Task 1 Workshop

International Nuclear Information System (INIS)

Nieuwlaar, E.; Alsema, E.

1997-12-01

During normal operation, photovoltaic (PV) power systems do not emit substances that may threaten human health or the environment. In fact, through the savings in conventional electricity production they can lead to significant emission reductions. There are, however, several indirect environmental impacts related to PV power systems that require further consideration. The production of present generation PV power systems is relatively energy intensive, involves the use of large quantities of bulk materials and (smaller) quantities of substances that are scarce and/or toxic. During operation, damaged modules or a fire may lead to the release of hazardous substances. Finally, at the end of their useful life time PV power systems have to be decommissioned, and resulting waste flows have to be managed. An expert workshop was held as part of the International Energy Agency Photovoltaic Power Systems Implementing Agreement Programme, to address these environmental aspects of PV power systems. The objectives of the workshop were: (a) review/overview of issues and approaches regarding environmental aspects of PV power systems; (b) enhanced clarity and consensus regarding e.g. Energy Pay-Back Time; (c) identification of issues of environmental importance regarding PV power systems ('hot spots'); (d) identification of issues requiring further attention ('white spots'); and (e) establish a network of researchers working on PV environmental issues. 25 participants from Europe, the United States, Japan, and Australia attended the workshop, representing the researchers in the field of environmental aspects of PV systems, R ampersand D managers, industry and utilities. The environmental issues that are considered most relevant for PV power systems were identified in the workshop as well as the approaches that may be used to investigate them. The main environmental issues discussed at the workshop were: energy use; resource depletion (e.g. the resource availability for indium

Target isolation system, high power laser and laser peening method and system using same

Science.gov (United States)

Dane, C. Brent; Hackel, Lloyd A.; Harris, Fritz

2007-11-06

A system for applying a laser beam to work pieces, includes a laser system producing a high power output beam. Target delivery optics are arranged to deliver the output beam to a target work piece. A relay telescope having a telescope focal point is placed in the beam path between the laser system and the target delivery optics. The relay telescope relays an image between an image location near the output of the laser system and an image location near the target delivery optics. A baffle is placed at the telescope focal point between the target delivery optics and the laser system to block reflections from the target in the target delivery optics from returning to the laser system and causing damage.

Workshop on Fundamental Science using Pulsed Power

Energy Technology Data Exchange (ETDEWEB)

Wootton, Alan [Univ. of Texas, Austin, TX (United States)

2016-02-20

The project objective was to fund travel to a workshop organized by the Institute for High Energy Density Science (IHEDS) at the University of Texas at Austin. In so doing the intent was to a) Grow the national academic High Energy Density Science (HEDS) community, b) Expand high impact, discovery driven fundamental HEDS, and c) Facilitate user-oriented research

Conductive cooling of high-power RIB targets

International Nuclear Information System (INIS)

Talbert, W.L.; Drake, D.M.; Wilson, M.T.; Lenz, J.W.; Hsu, H.-H.

2002-01-01

A short review is presented of target cooling approaches suggested for targets irradiated by intense high-energy proton beams to produce radioactive species for use in a broad range of physics studies. This work reports on conductive cooling approaches for operation at temperatures lower than effective for radiative cooling. The possibilities for conductive cooling are discussed, and a prototype test target is described. This target was constructed for an experiment, designed to validate the numerical analysis approaches, at the TRIUMF/ISAC facility. Fabrication issues and the results of the experiment are presented, followed by a discussion of the implications of the experiment outcome for future development of targets to produce intense beams of radioactive ions

SUPPORT FOR HU CFRT SUMMER HIGH SCHOOL FUSION WORKSHOP

International Nuclear Information System (INIS)

Punjabi, Alkesh

2010-01-01

Nine summer fusion science research workshops for minority and female high school students were conducted at the Hampton University Center for Fusion Research and Training from 1996 to 2005. Each workshop was of the duration of eight weeks. In all 35 high school students were mentored. The students presented 28 contributed papers at the annual meetings of the American Physical Society Division of Plasma Physics. These contributed papers were very well received by the plasma physics and fusion science research community. The students won a number of prestigious local, state, and national honors, awards, prizes, and scholarships. The notable among these are the two regional finalist positions in the 1999 Siemens-Westinghouse Science and Technology Competitions; 1st Place U.S. Army Award, 2006; 1st Place U.S. Naval Science Award, 2006; Yale Science and Engineering Association Best 11th Grade Project, 2006; Society of Physics Students Book Award, 2006; APS Corporate Minority Scholarship and others. This workshop program conducted by the HU CFRT has been an exemplary success, and served the minority and female students exceptionally fruitfully. The Summer High School Fusion Science Workshop is an immensely successful outreach activity conducted by the HU CFRT. In this workshop, we train, motivate, and provide high quality research experiences to young and talented high school scholars with emphasis on under-represented minorities and female students in fusion science and related areas. The purpose of this workshop is to expose minority and female students to the excitement of research in science at an early stage in their academic lives. It is our hope that this may lead the high school students to pursue higher education and careers in physical sciences, mathematics, and perhaps in fusion science. To our knowledge, this workshop is the first and only one to date, of fusion science for under-represented minorities and female high school students at an HBCU. The faculty

Comparisons of Reflectance Targets at the Above Water Radiometry Workshop on Long Island Sound, August 4 - 6, 2010

Science.gov (United States)

Johnson, B.; Fargion, G. S.; Saunders, R. D.; Ondrusek, M. E.

2012-12-01

On August 4-5, 2010, members from the satellite remote sensing community participated in a workshop off the coast of Long Island, New York. The participant's objective was to interpret and implement recently published protocols for measuring normalized, water-leaving spectral radiances by above-water in situ radiometry and compare the results. Each research team applied the protocols to the measurement of the water's surface and three reflectance standard targets supplied by NIST - a white and a gray diffuse reflectance target and a blue ground-glass target. The reflectance values of the water's surface and the test targets were derived and analyzed by each team. We report on the workshop detailing the methods for comparison of the participant's results of the test targets. The workshop served as a preparation for the vigorous validation activities that occurred following the launch of the Visible Infrared Imager Radiometer Suite (VIIRS). Above water, in situ, radiometric measurements using uncalibrated radiometers and standard diffuse reflectance targets are one method used by researchers to validate the VIIRS data products. The Joint Polar Satellite System (JPSS) office provided support to NIST for this work (NA12AANEG0230).

Third EC/ISOE workshop on occupational exposure management at nuclear power plants

International Nuclear Information System (INIS)

Bone, Mike; Morris, Simon

2002-01-01

The third workshop was jointly sponsored by the IAEA and OECD Nuclear Energy Agency. It was organised by the European Commission Directorate-General for the Environment, Nuclear Safety and Civil Protection and the ISOE European Regional Technical Centre. The workshop provided a forum for Health Physics practitioners and operators to exchange information and experience on occupational exposure issues at Nuclear Power Plants (NPPs). There were approximately 130 participants of whom 63% were from utilities, 11% from contractors and 26% from regulatory bodies

ISC High Performance 2017 International Workshops, DRBSD, ExaComm, HCPM, HPC-IODC, IWOPH, IXPUG, P^3MA, VHPC, Visualization at Scale, WOPSSS

CERN Document Server

Yokota, Rio; Taufer, Michela; Shalf, John

2017-01-01

This book constitutes revised selected papers from 10 workshops that were held as the ISC High Performance 2017 conference in Frankfurt, Germany, in June 2017. The 59 papers presented in this volume were carefully reviewed and selected for inclusion in this book. They stem from the following workshops: Workshop on Virtualization in High-Performance Cloud Computing (VHPC) Visualization at Scale: Deployment Case Studies and Experience Reports International Workshop on Performance Portable Programming Models for Accelerators (P^3MA) OpenPOWER for HPC (IWOPH) International Workshop on Data Reduction for Big Scientific Data (DRBSD) International Workshop on Communication Architectures for HPC, Big Data, Deep Learning and Clouds at Extreme Scale Workshop on HPC Computing in a Post Moore's Law World (HCPM) HPC I/O in the Data Center ( HPC-IODC) Workshop on Performance and Scalability of Storage Systems (WOPSSS) IXPUG: Experiences on Intel Knights Landing at the One Year Mark International Workshop on Communicati...

A free-jet Hg target operating in a high magnetic field intersecting a high-power proton beam

Science.gov (United States)

Van Graves; Spampinato, Philip; Gabriel, Tony; Kirk, Harold; Simos, Nicholas; Tsang, Thomas; McDonald, Kirk; Peter Titus; Fabich, Adrian; Haseroth, Helmut; Lettry, Jacques

2006-06-01

A proof-of-principal experiment to investigate the interaction of a proton beam, high magnetic field, and high- Z target is planned to take place at CERN in early 2007. This experiment is part of the Muon Collider Collaboration, with participants from Brookhaven National Laboratory, Princeton University, Massachusetts Institute Of Technology, European Organization for Nuclear Research-CERN, Rutherford Appleton Laboratory, and Oak Ridge National Laboratory. An unconstrained mercury jet target system that interacts with a high power (1 MW) proton beam in a high magnetic field (15 T) is being designed. The Hg jet diameter is 1-cm with a velocity up to 20 m/s. A laser optical diagnostic system will be incorporated into the target design to permit observation of the dispersal of the jet resulting from interaction with a 24 GeV proton beam with up to 20×10 12 ppp. The target system includes instruments for sensing mercury vapor, temperature, flow rate, and sump tank level, and the means to position the jet relative to the magnetic axis of a solenoid and the proton beam. The design considerations for the system include all issues dealing with safely handling approximately 23 l of Hg, transporting the target system and the mercury to CERN, decommissioning the experiment, and returning the mildly activated equipment and Hg to the US.

Workshop on Hydrogen Storage and Generation for Medium-Power and -Energy Applications

National Research Council Canada - National Science Library

Matthews, Michael

1998-01-01

This report summarizes the Workshop on Hydrogen Storage and Generation Technologies for Medium-Power and -Energy Applications which was held on April 8-10, 1997 at the Radisson Hotel Orlando Airport in Orlando, Florida...

High-power liquid-lithium target prototype for accelerator-based boron neutron capture therapy.

Science.gov (United States)

Halfon, S; Paul, M; Arenshtam, A; Berkovits, D; Bisyakoev, M; Eliyahu, I; Feinberg, G; Hazenshprung, N; Kijel, D; Nagler, A; Silverman, I

2011-12-01

A prototype of a compact Liquid-Lithium Target (LiLiT), which will possibly constitute an accelerator-based intense neutron source for Boron Neutron Capture Therapy (BNCT) in hospitals, was built. The LiLiT setup is presently being commissioned at Soreq Nuclear Research Center (SNRC). The liquid-lithium target will produce neutrons through the (7)Li(p,n)(7)Be reaction and it will overcome the major problem of removing the thermal power generated using a high-intensity proton beam (>10 kW), necessary for sufficient neutron flux. In off-line circulation tests, the liquid-lithium loop generated a stable lithium jet at high velocity, on a concave supporting wall; the concept will first be tested using a high-power electron beam impinging on the lithium jet. High intensity proton beam irradiation (1.91-2.5 MeV, 2-4 mA) will take place at Soreq Applied Research Accelerator Facility (SARAF) superconducting linear accelerator currently in construction at SNRC. Radiological risks due to the (7)Be produced in the reaction were studied and will be handled through a proper design, including a cold trap and appropriate shielding. A moderator/reflector assembly is planned according to a Monte Carlo simulation, to create a neutron spectrum and intensity maximally effective to the treatment and to reduce prompt gamma radiation dose risks. Copyright © 2011 Elsevier Ltd. All rights reserved.

Summary of Information Presented at an NRC-Sponsored Low-Power Shutdown Public Workshop, April 27, 1999, Rockville, Maryland

International Nuclear Information System (INIS)

Wheeler, Timothy A.; Whitehead, Donnie W.; Lois, Erasmia

1999-01-01

This report summarizes a public workshop that was held on April 27, 1999, in Rockville, Maryland. The workshop was conducted as part of the US Nuclear Regulatory Commission's (NRC) efforts to further develop its understanding of the risks associated with low power and shutdown operations at US nuclear power plants. A sufficient understanding of such risks is required to support decision-making for risk-informed regulation, in particular Regulatory Guide 1.174, and the development of a consensus standard. During the workshop the NRC staff discussed and requested feedback from the public (including representatives of the nuclear industry, state governments, consultants, private industry, and the media) on the risk associated with low-power and shutdown operations

Summary of Information Presented at an NRC-Sponsored Low-Power Shutdown Public Workshop, April 27, 1999, Rockville, Maryland

Energy Technology Data Exchange (ETDEWEB)

Wheeler, Timothy A.; Whitehead, Donnie W.; Lois, Erasmia

1999-07-01

This report summarizes a public workshop that was held on April 27, 1999, in Rockville, Maryland. The workshop was conducted as part of the US Nuclear Regulatory Commission's (NRC) efforts to further develop its understanding of the risks associated with low power and shutdown operations at US nuclear power plants. A sufficient understanding of such risks is required to support decision-making for risk-informed regulation, in particular Regulatory Guide 1.174, and the development of a consensus standard. During the workshop the NRC staff discussed and requested feedback from the public (including representatives of the nuclear industry, state governments, consultants, private industry, and the media) on the risk associated with low-power and shutdown operations.

ISC High Performance 2016 International Workshops, ExaComm, E-MuCoCoS, HPC-IODC, IXPUG, IWOPH, P^3MA, VHPC, WOPSSS

CERN Document Server

Mohr, Bernd; Kunkel, Julian M

2016-01-01

This book constitutes revised selected papers from 7 workshops that were held in conjunction with the ISC High Performance 2016 conference in Frankfurt, Germany, in June 2016. The 45 papers presented in this volume were carefully reviewed and selected for inclusion in this book. They stem from the following workshops: Workshop on Exascale Multi/Many Core Computing Systems, E-MuCoCoS; Second International Workshop on Communication Architectures at Extreme Scale, ExaComm; HPC I/O in the Data Center Workshop, HPC-IODC; International Workshop on OpenPOWER for HPC, IWOPH; Workshop on the Application Performance on Intel Xeon Phi – Being Prepared for KNL and Beyond, IXPUG; Workshop on Performance and Scalability of Storage Systems, WOPSSS; and International Workshop on Performance Portable Programming Models for Accelerators, P3MA.

Target studies for the neutrino factory at the Rutherford Appleton laboratory

International Nuclear Information System (INIS)

Drumm, Paul; Densham, Chris; Bennett, Roger

2001-01-01

Target studies at the Rutherford Appleton Laboratory have concentrated on studies of a solid heavy metal target. The suggestion to use a radiatively cooled target which rotates in beam was made shortly after the first NuFact workshop as a means of dissipating large amounts of power at a high temperature, and as an alternative to the proposed water-cooled rotating band and liquid metal jet targets. This paper examines the proposed drive scheme for the target ring, which uses induced currents and magnetic forces to both levitate and drive the target. Estimates of the power required to levitate and drive the target ring and the forces exerted on the moving ring as it enters the target capture solenoid are given. One of the principle concerns in the operation of a solid target is the severe shock stress experienced due to the impact of an intense energetic proton beam in a short time compared to the transit time of sound in the material. Calculations of the stresses induced in the target ring and their evolution with time as well as an initial estimation of the expected power densities and stresses in an existing high power density target are presented

Substantial difference in target surface chemistry between reactive dc and high power impulse magnetron sputtering

Science.gov (United States)

Greczynski, G.; Mráz, S.; Schneider, J. M.; Hultman, L.

2018-02-01

The nitride layer formed in the target race track during the deposition of stoichiometric TiN thin films is a factor 2.5 thicker for high power impulse magnetron sputtering (HIPIMS), compared to conventional dc processing (DCMS). The phenomenon is explained using x-ray photoelectron spectroscopy analysis of the as-operated Ti target surface chemistry supported by sputter depth profiles, dynamic Monte Carlo simulations employing the TRIDYN code, and plasma chemical investigations by ion mass spectrometry. The target chemistry and the thickness of the nitride layer are found to be determined by the implantation of nitrogen ions, predominantly N+ and N2+ for HIPIMS and DCMS, respectively. Knowledge of this method-inherent difference enables robust processing of high quality functional coatings.

MO-AB-210-00: Diagnostic Ultrasound Imaging Quality Control and High Intensity Focused Ultrasound Therapy Hands-On Workshop

International Nuclear Information System (INIS)

2015-01-01

The goal of this ultrasound hands-on workshop is to demonstrate advancements in high intensity focused ultrasound (HIFU) and to demonstrate quality control (QC) testing in diagnostic ultrasound. HIFU is a therapeutic modality that uses ultrasound waves as carriers of energy. HIFU is used to focus a beam of ultrasound energy into a small volume at specific target locations within the body. The focused beam causes localized high temperatures and produces a well-defined regions of necrosis. This completely non-invasive technology has great potential for tumor ablation and targeted drug delivery. At the workshop, attendees will see configurations, applications, and hands-on demonstrations with on-site instructors at separate stations. The involvement of medical physicists in diagnostic ultrasound imaging service is increasing due to QC and accreditation requirements. At the workshop, an array of ultrasound testing phantoms and ultrasound scanners will be provided for attendees to learn diagnostic ultrasound QC in a hands-on environment with live demonstrations of the techniques. Target audience: Medical physicists and other medical professionals in diagnostic imaging and radiation oncology with interest in high-intensity focused ultrasound and in diagnostic ultrasound QC. Learning Objectives: Learn ultrasound physics and safety for HIFU applications through live demonstrations Get an overview of the state-of-the art in HIFU technologies and equipment Gain familiarity with common elements of a quality control program for diagnostic ultrasound imaging Identify QC tools available for testing diagnostic ultrasound systems and learn how to use these tools List of supporting vendors for HIFU and diagnostic ultrasound QC hands-on workshop: Philips Healthcare Alpinion Medical Systems Verasonics, Inc Zonare Medical Systems, Inc Computerized Imaging Reference Systems (CIRS), Inc. GAMMEX, Inc., Cablon Medical BV Steffen Sammet: NIH/NCI grant 5R25CA132822, NIH/NINDS grant 5R25NS

MO-AB-210-00: Diagnostic Ultrasound Imaging Quality Control and High Intensity Focused Ultrasound Therapy Hands-On Workshop

Energy Technology Data Exchange (ETDEWEB)

NONE

2015-06-15

The goal of this ultrasound hands-on workshop is to demonstrate advancements in high intensity focused ultrasound (HIFU) and to demonstrate quality control (QC) testing in diagnostic ultrasound. HIFU is a therapeutic modality that uses ultrasound waves as carriers of energy. HIFU is used to focus a beam of ultrasound energy into a small volume at specific target locations within the body. The focused beam causes localized high temperatures and produces a well-defined regions of necrosis. This completely non-invasive technology has great potential for tumor ablation and targeted drug delivery. At the workshop, attendees will see configurations, applications, and hands-on demonstrations with on-site instructors at separate stations. The involvement of medical physicists in diagnostic ultrasound imaging service is increasing due to QC and accreditation requirements. At the workshop, an array of ultrasound testing phantoms and ultrasound scanners will be provided for attendees to learn diagnostic ultrasound QC in a hands-on environment with live demonstrations of the techniques. Target audience: Medical physicists and other medical professionals in diagnostic imaging and radiation oncology with interest in high-intensity focused ultrasound and in diagnostic ultrasound QC. Learning Objectives: Learn ultrasound physics and safety for HIFU applications through live demonstrations Get an overview of the state-of-the art in HIFU technologies and equipment Gain familiarity with common elements of a quality control program for diagnostic ultrasound imaging Identify QC tools available for testing diagnostic ultrasound systems and learn how to use these tools List of supporting vendors for HIFU and diagnostic ultrasound QC hands-on workshop: Philips Healthcare Alpinion Medical Systems Verasonics, Inc Zonare Medical Systems, Inc Computerized Imaging Reference Systems (CIRS), Inc. GAMMEX, Inc., Cablon Medical BV Steffen Sammet: NIH/NCI grant 5R25CA132822, NIH/NINDS grant 5R25NS

High-current negative-ion sources for pulsed spallation neutron sources: LBNL workshop, October 1994

International Nuclear Information System (INIS)

Alonso, J.R.

1995-09-01

The neutron scattering community has endorsed the need for a high-power (1 to 5 MW) accelerator-driven source of neutrons for materials research. Properly configured, the accelerator could produce very short (sub-microsecond) bursts of cold neutrons, said time structure offering advantages over the continuous flux from a reactor. The recent cancellation of the ANS reactor project has increased the urgency to develop a comprehensive strategy based on the best technological scenarios. Studies to date have built on the experience from ISIS (the 160 kW source in the UK), and call for a high-current (approx. 100 mA peak) H- source-linac combination injecting into one or more accumulator rings in which beam may be further accelerated. The I to 5 GeV proton beam is extracted in a single turn and brought to the target-moderator stations. The high current, high duty-factor, high brightness and high reliability required of the ion source present a very large challenge to the ion source community. The Workshop reported on here, held in Berkeley in October 1994, analyzed in detail the source requirements for proposed accelerator scenarios, the present performance capabilities of different H- source technologies, and identified necessary R ampersand D efforts to bridge the gap

EDITORIAL: Selected papers from the 10th International Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2010) Selected papers from the 10th International Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2010)

Science.gov (United States)

Reynaerts, Dominiek; Vullers, Ruud

2011-10-01

This special section of Journal of Micromechanics and Microengineering features papers selected from the 10th International Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2010). The workshop was organized in Leuven, Belgium from 30 November to 3 December 2010 by Katholieke Universiteit Leuven and the imec/Holst Centre. This was a special PowerMEMS Workshop, for several reasons. First of all, we celebrated the 10th anniversary of the workshop: the first PowerMEMS meeting was organized in Sendai, Japan in 2000. None of the organizers or participants of this first meeting could have predicted the impact of the workshop over the next decade. The second reason was that, for the first time, the conference organization spanned two countries: Belgium and the Netherlands. Thanks to the advances in information technology, teams from Katholieke Universiteit Leuven (Belgium) and the imec/Holst Centre in Eindhoven (the Netherlands) have been able to work together seamlessly as one team. The objective of the PowerMEMS Workshop is to stimulate innovation in micro and nanotechnology for power generation and energy conversion applications. Its scope ranges from integrated microelectromechanical systems (MEMS) for power generation, dissipation, harvesting, and management, to novel nanostructures and materials for energy-related applications. True to the objective of the PowerMEMSWorkshop, the 2010 technical program covered a broad range of energy related research, ranging from the nanometer to the millimeter scale, discussed in 5 invited and 52 oral presentations, and 112 posters. This special section includes 14 papers covering vibration energy harvesters, thermal applications and micro power systems. Finally, we wish to express sincere appreciation to the members of the International Steering Committee, the Technical Program Committee and last but not least the Local Organizing Committee. This special issue was edited in

Obesity Prevention from Conception: A Workshop to Guide the Development of a Pan-Canadian Trial Targeting the Gestational Period

Directory of Open Access Journals (Sweden)

Kristi B. Adamo

2014-01-01

Full Text Available This report summarizes a meeting, Obesity Prevention from Conception , held in Ottawa in 2012. This planning workshop was funded by the Canadian Institutes of Health Research (CIHR to bring together researchers with expertise in the area of maternal obesity (OB and weight gain in pregnancy and pregnancy-related disease to attend a one-day workshop and symposium to discuss the development of a cross-Canada lifestyle intervention trial for targeting pregnant women. This future intervention will aim to reduce downstream OB in children through encouraging appropriate weight gain during the mother's pregnancy. The workshop served to (i inform the development of a lifestyle intervention for women with a high pre-pregnancy body mass index (BMI, (ii identify site investigators across Canada, and (iii guide the development of a grant proposal focusing on the health of mom and baby. A brief summary of the presentations as well as the focus groups is presented for use in planning future research.

Executive Summary High-Yield Scenario Workshop Series Report

Energy Technology Data Exchange (ETDEWEB)

Leslie Park Ovard; Thomas H. Ulrich; David J. Muth Jr.; J. Richard Hess; Steven Thomas; Bryce Stokes

2009-12-01

To get a collective sense of the impact of research and development (R&D) on biomass resource availability, and to determine the feasibility that yields higher than baseline assumptions used for past assessments could be achieved to support U.S. energy independence, an alternate “High-Yield Scenario” (HYS) concept was presented to industry experts at a series of workshops held in December 2009. The workshops explored future production of corn/agricultural crop residues, herbaceous energy crops (HECs), and woody energy crops (WECs). This executive summary reports the findings of that workshop.

SLAC workshop on high energy electroproduction and spin physics

International Nuclear Information System (INIS)

1992-01-01

These Proceedings contain copies of the transparencies presented at the Workshop on High Energy Electroproduction and Spin Physics held at SLAC on February 5--8, 1992. The purpose of this Workshop was to bring people together to discuss the possibilities for new experiments using the SLAC high intensity electron and photon beams and the facilities of End Station A

Feasibility of High Power Refractory Metal Foil-Targets for EURISOL

CERN Document Server

R. Wilfinger, J. Lettry and the EURISOL Task 3 Workgroup

Radioisotopes are produced by the ISOL method in thick targets. In existing ISOL facilities, only small yields have been obtained for short-lived nuclei close to the driplines due to the radioactive decay during the diffusion, effusion and ionization processes. An increase of the proton beam current increases the production rate, which is directly proportional to the primary proton flux. But at the same time, the power deposition inside the target is also increased proportional to the primary proton flux...

Proceedings of international workshop on utilization of nuclear power in oceans (N'ocean 2000)

International Nuclear Information System (INIS)

Yamaji, A.; Nariyama, N.; Sawada, K.

2000-03-01

Human beings and the ocean have maintained close relations for a long time. The ocean produced the life at very old time and human beings have been benefited by ocean, particularly in Japan that is surrounded by the ocean. In the utilization of nuclear power in ocean, Japan has been very active from the beginning of the development of nuclear power. The nuclear powered ship MUTSU has been developed and completed the experimental voyage. Besides the nuclear powered ship, we are using the ocean for the transportation of radioactive materials. This International Workshop aimed at offering further information about nuclear utilization in oceans such as icebreakers, deep-sea submarines, high speed carriers, floating plant, desalination and heating plants, radioactive materials transport ships, and so on. The discussions on the economical, environmental and scientific effects are included. The 36 of the present papers are indexed individually. (J.P.N.)

EURISOL High Power Targets

CERN Document Server

Kadi, Y; Lindroos, M; Ridikas, D; Stora, T; Tecchio, L; CERN. Geneva. BE Department

2009-01-01

Modern Nuclear Physics requires access to higher yields of rare isotopes, that relies on further development of the In-flight and Isotope Separation On-Line (ISOL) production methods. The limits of the In-Flight method will be applied via the next generation facilities FAIR in Germany, RIKEN in Japan and RIBF in the USA. The ISOL method will be explored at facilities including ISAC-TRIUMF in Canada, SPIRAL-2 in France, SPES in Italy, ISOLDE at CERN and eventually at the very ambitious multi-MW EURISOL facility. ISOL and in-flight facilities are complementary entities. While in-flight facilities excel in the production of very short lived radioisotopes independently of their chemical nature, ISOL facilities provide high Radioisotope Beam (RIB) intensities and excellent beam quality for 70 elements. Both production schemes are opening vast and rich fields of nuclear physics research. In this article we will introduce the targets planned for the EURISOL facility and highlight some of the technical and safety cha...

IFMIF-CDA technical workshop on lithium target system. Proceedings

International Nuclear Information System (INIS)

1995-09-01

An intense neutron source, International Fusion Materials Irradiation Facility (IFMIF) is planned under the collaborative program by International Energy Agency (IEA), and the Conceptual Design Activity (CDA) started in February 1995. US, Japan and EU are responsible to take a lead in coordinating accelerator, target and test cell design, respectively. In order to exchange the current results of the study and to coordinate the activities for the design integration, the first technical workshop on the lithium target system was held in the period of July 18-21 at the Tokai Research Establishment of the JAERI. This publication summarizes the materials presented in this meeting. The presentations and discussions were organized with the identified CDA tasks. It was confirmed that the reference design of the IFMIF target based on the previous studies under FMIT and ESNIT, elaborated to meet IFMIF parameters, is reasonable and feasible. It was pointed out that the interface between accelerator and test cell subsystems should be carefully investigated to avoid technical conflicts. Some design options such as nozzle, backwall and lithium jet geometry, lithium purity control, and lithium vapor control, based on the current technology were proposed to improve the integral target system function, and further R and D studies were suggested for design integration. (author)

Proceedings of the Third International Workshop on the implementation of ALARA at nuclear power plants

International Nuclear Information System (INIS)

Khan, T.A.; Roecklein, A.K.

1995-03-01

This report contains the papers presented and the discussions that took place at the Third International Workshop on ALARA Implementation at Nuclear Power Plants, held in Hauppauge, Long Island, New York from May 8--11, 1994. The purpose of the workshop was to bring together scientists, engineers, health physicists, regulators, managers and other persons who are involved with occupational dose control and ALARA issues. The countries represented were: Canada, Finland, France, Germany, Japan, Korea, Mexico, the Netherlands, Spain, Sweden, the United Kingdom and the United States. The workshop was organized into twelve sessions and three panel discussions. Individual papers have been cataloged separately

Proceedings of the Third International Workshop on the implementation of ALARA at nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Khan, T.A. [comp.] [Brookhaven National Lab., Upton, NY (United States); Roecklein, A.K. [Nuclear Regulatory Commission, Washington, DC (United States). Div. of Regulatory Applications

1995-03-01

This report contains the papers presented and the discussions that took place at the Third International Workshop on ALARA Implementation at Nuclear Power Plants, held in Hauppauge, Long Island, New York from May 8--11, 1994. The purpose of the workshop was to bring together scientists, engineers, health physicists, regulators, managers and other persons who are involved with occupational dose control and ALARA issues. The countries represented were: Canada, Finland, France, Germany, Japan, Korea, Mexico, the Netherlands, Spain, Sweden, the United Kingdom and the United States. The workshop was organized into twelve sessions and three panel discussions. Individual papers have been cataloged separately.

Aircraft Electric/Hybrid-Electric Power and Propulsion Workshop Perspective of the V/STOL Aircraft Systems Tech Committee

Science.gov (United States)

Hange, Craig E.

2016-01-01

This presentation will be given at the AIAA Electric Hybrid-Electric Power Propulsion Workshop on July 29, 2016. The workshop is being held so the AIAA can determine how it can support the introduction of electric aircraft into the aerospace industry. This presentation will address the needs of the community within the industry that advocates the use of powered-lift as important new technologies for future aircraft and air transportation systems. As the current chairman of the VSTOL Aircraft Systems Technical Committee, I will be presenting generalized descriptions of the past research in developing powered-lift and generalized observations on how electric and hybrid-electric propulsion may provide advances in the powered-lift field.

The Art of Teaching the Arts: A Workshop for High School Teachers

Science.gov (United States)

Annenberg Media, 2005

2005-01-01

"The Art of Teaching the Arts: A Workshop for High School Teachers" is an eight-part professional development workshop for use by high school dance, music, theatre, and visual art teachers. The workshop examines how principles of good teaching are carried out in teaching the arts at the high school level. In the eight one-hour video programs,…

Workshop: High-performance coatings for internal combustion engines; Workshop: Hochleistungsschichten fuer Verbrennungsmotoren

Energy Technology Data Exchange (ETDEWEB)

Blau, W. [Foerdergemeinschaft Duenne Schichten e.V., Dresden (Germany). Transferzentrum Oberflaechen- und Schichttechnologie; Lugscheider, E. [Technische Hochschule Aachen (Germany). Lehr- und Forschungsgebiet Werkstoffwissenschaften; Suchentrunk, R. (comps.) [DaimlerChrysler Aerospace AG (Dasa), Muenchen (Germany)

1999-07-01

Progress in vehicles is closely related to progress in materials. Engine components must withstand high thermal, corrosive and mechanical loads. The workshop focused on the coating and boundary layer treatment of components especially of piston engines, although gas turbine technology was gone into as well. [German] Fortschritte in der Verkehrstechnik sind oft eng mit Fortschritten in der Werkstofftechnik verknuepft. Besonders hoch sind die Anforderungen hinsichtlich thermischer, korrosiver und mechanischer Belastbarkeit bei Bauteilen von Verbrennungsmotoren. Der Workshop widmet sich ausschliesslich dem Teilgebiet die Beschichtung und Randschichtbehandlung von Bauteilen. Kolbenmotoren stehen im Mittelpunkt, Querverbindungen zur Gasturbinentechnik werden angesprochen. (orig./AKF)

Mechanical design and development of a high power target system for the SLC Positron Source

International Nuclear Information System (INIS)

Reuter, E.; Mansour, D.; Porter, T.; Sax, W.; Szumillo, A.

1991-12-01

In order to bring the SLC Positron Source luminosity up to design specifications, the previous (stationary) positron target had to be replaced with a version which could reliably dissipate the higher power levels and cyclic pulsed thermal stresses of the high intensity 33GeV electron beam. In addition to this basic requirement, the new target system had to meet SLAC's specifications for Ultra High Vacuum, be remotely controllable, ''radiation hard,'' and designed in such a way that it could be removed and replaced quickly and easily with minimum personnel exposure to radiation. It was also desirable to integrate the target and collection components into a compact, easily manufacturable, and easily maintainable module. This paper briefly summarize the mechanical design and development of the new modular target system, its associated controls and software, alignment, and the quick removal system. Operational experience gained with the new system over the first running cycle is also summarized

CEBAF/SURA 1984 summer workshop: Proceedings

International Nuclear Information System (INIS)

Gross, F.; Whitney, R.R.

1984-11-01

This report discusses the following topics: Summary: Magnetic Spectrometer Working Group; Workshop Report: Internal Targets and Tagged Photons; Nucleon Physics with Chromodynamics: From High Q 2 to Baryon Spectroscopy to Nuclear Physics; Quark Signatures in Nuclear Physics; What Can We Learn About the Three-Nucleon Wave Functions from High Energy Electrons; Coincidence and Polarization Measurements with High-Energy Electrons; NPAS -- a Program of Nuclear Physics at SLAC; Spectrometers; Polarized Gas Targets in Electron Rings; Photonuclear Experiments Using Large Acceptance Detectors; 4 π Detectors; Magnetic Spectrometer Working Group Report; Workshop Report: Tagged Photons - Low Current Electron Beams and Large Acceptance - 4 π Detectors; Positron Beams at CEBAF; Lampshade Magnet for a Large-Aperture Detector; Meson Exchange in Relativistic Quark Models; Electron Scattering from Discrete Low-Lying Levels of 13 C at High Momentum Transfer; NN Potential With a Six Quark Core from the Constituent Quark Model; A Study of (e,e'N) Reactions from Nuclear Targets; Study of Complex Nuclei Using Internal Targets at CEBAF; The Kaon-Nucleon Interaction in a Quark Potential Model; and Current Conservation and Magnetic Form Factors of 3 He, 3 H

HARD PARTON PHYSICS IN HIGH ENERGY NUCLEAR COLLISIONS. PROCEEDINGS OF RIKEN BNL RESEARCH CENTER WORKSHOP, VOLUME 17

Energy Technology Data Exchange (ETDEWEB)

CARROLL,J.

1999-09-10

The RIKEN-BNL center workshop on ''Hard parton physics in high energy nuclear collisions'' was held at BNL from March 1st-5th! 1999. The focus of the workshop was on hard probes of nucleus-nucleus collisions that will be measured at RHIC with the PHENIX and STAR detectors. There were about 45 speakers and over 70 registered participants at the workshop, with roughly a quarter of the speakers from overseas. About 60% of the talks were theory talks. A nice overview of theory for RHIC was provided by George Sterman. The theoretical talks were on a wide range of topics in QCD which can be classified under the following: (a) energy loss and the Landau-Pomeranchuk-Migdal effect; (b) minijet production and equilibration; (c) small x physics and initial conditions; (d) nuclear parton distributions and shadowing; (e) spin physics; (f) photon, di-lepton, and charm production; and (g) hadronization, and simulations of high pt physics in event generators. Several of the experimental talks discussed the capabilities of the PHENIX and STAR detectors at RHIC in measuring high pt particles in heavy ion collisions. In general, these talks were included in the relevant theory sessions. A session was set aside to discuss the spin program at RHIC with polarized proton beams. In addition, there were speakers from 08, HERA, the fixed target experiments at Fermilab, and the CERN fixed target Pb+Pb program, who provided additional perspective on a range of issues of relevance to RHIC; from jets at the Tevatron, to saturation of parton distributions at HERA, and recent puzzling data on direct photon production in fixed target experiments, among others.

Radiation physics of high power spallation targets. State of the art simulation methods and experiments, the 'European Spallation Source' (ESS)

International Nuclear Information System (INIS)

Filges, D.; Cloth, P.; Neef, R.D.; Schaal, H.

1998-01-01

Particle transport and nuclear interactions of planned high power spallation targets with GeV proton beams can be simulated using widely developed Monte Carlo transport methods. This includes available high energy radiation transport codes and systems for low energy, earlier developed for reactor physics and fusion technology. Monte Carlo simulation codes and applied methods are discussed. The capabilities of the world-wide existing state-of-the-art computer code systems are demonstrated. Results of computational studies for the 'European Spallation Source' (ESS) mercury high power target station are given. The needs for spallation related data and planned experiments are shown. (author)

High performance inertial fusion targets

International Nuclear Information System (INIS)

Nuckolls, J.H.; Bangerter, R.O.; Lindl, J.D.; Mead, W.C.; Pan, Y.L.

1978-01-01

Inertial confinement fusion (ICF) target designs are considered which may have very high gains (approximately 1000) and low power requirements (< 100 TW) for input energies of approximately one megajoule. These include targets having very low density shells, ultra thin shells, central ignitors, magnetic insulation, and non-ablative acceleration

MO-AB-210-03: Workshop

International Nuclear Information System (INIS)

Lu, Z.

2015-01-01

The goal of this ultrasound hands-on workshop is to demonstrate advancements in high intensity focused ultrasound (HIFU) and to demonstrate quality control (QC) testing in diagnostic ultrasound. HIFU is a therapeutic modality that uses ultrasound waves as carriers of energy. HIFU is used to focus a beam of ultrasound energy into a small volume at specific target locations within the body. The focused beam causes localized high temperatures and produces a well-defined regions of necrosis. This completely non-invasive technology has great potential for tumor ablation and targeted drug delivery. At the workshop, attendees will see configurations, applications, and hands-on demonstrations with on-site instructors at separate stations. The involvement of medical physicists in diagnostic ultrasound imaging service is increasing due to QC and accreditation requirements. At the workshop, an array of ultrasound testing phantoms and ultrasound scanners will be provided for attendees to learn diagnostic ultrasound QC in a hands-on environment with live demonstrations of the techniques. Target audience: Medical physicists and other medical professionals in diagnostic imaging and radiation oncology with interest in high-intensity focused ultrasound and in diagnostic ultrasound QC. Learning Objectives: Learn ultrasound physics and safety for HIFU applications through live demonstrations Get an overview of the state-of-the art in HIFU technologies and equipment Gain familiarity with common elements of a quality control program for diagnostic ultrasound imaging Identify QC tools available for testing diagnostic ultrasound systems and learn how to use these tools List of supporting vendors for HIFU and diagnostic ultrasound QC hands-on workshop: Philips Healthcare Alpinion Medical Systems Verasonics, Inc Zonare Medical Systems, Inc Computerized Imaging Reference Systems (CIRS), Inc. GAMMEX, Inc., Cablon Medical BV Steffen Sammet: NIH/NCI grant 5R25CA132822, NIH/NINDS grant 5R25NS

Pressure and stress waves in a spallation neutron source mercury target generated by high-power proton pulses

CERN Document Server

Futakawa, M; Conrad, H; Stechemesser, H

2000-01-01

The international ASTE collaboration has performed a first series of measurements on a spallation neutron source target at the Alternating Gradient Synchrotron (AGS) in Brookhaven. The dynamic response of a liquid mercury target hit by high-power proton pulses of about 40 ns duration has been measured by a laser Doppler technique and compared with finite elements calculations using the ABAQUS code. It is shown that the calculation can describe the experimental results for at least the time interval up to 100 mu s after the pulse injection. Furthermore, it has been observed that piezoelectric pressure transducers cannot be applied in the high gamma-radiation field of a spallation target.

PREFACE: High Energy Particle Physics Workshop (HEPPW2015)

Science.gov (United States)

Cornell, Alan S.; Mellado, B.

2015-10-01

The motivation for this workshop began with the discovery of the Higgs boson three years ago, and the realisation that many problems remain in particle physics, such as why there is more matter than anti-matter, better determining the still poorly measured parameters of the strong force, explaining possible sources for dark matter, naturalness etc. While the newly discovered Higgs boson seems to be compatible with the Standard Model, current experimental accuracy is far from providing a definitive statement with regards to the nature of this new particle. There is a lot of room for physics beyond the Standard Model to emerge in the exploration of the Higgs boson. Recent measurements in high-energy heavy ion collisions at the LHC have shed light on the complex dynamics that govern high-density quark-gluon interactions. An array of results from the ALICE collaboration have been highlighted in a recent issue of CERN courier. The physics program of high-energy heavy ion collisions promises to further unveil the intricacies of high-density quark-gluon plasma physics. The great topicality of high energy physics research has also seen a rapid increase in the number of researchers in South Africa pursuing such studies, both experimentally through the ATLAS and ALICE colliders at CERN, and theoretically. Young researchers and graduate students largely populate these research groups, with little experience in presenting their work, and few support structures (to their knowledge) to share experiences with. Whilst many schools and workshops have sought to educate these students on the theories and tools they will need to pursue their research, few have provided them with a platform to present their work. As such, this workshop discussed the various projects being pursued by graduate students and young researchers in South Africa, enabling them to develop networks for future collaboration and discussion. The workshop took place at the iThemba Laboratories - North facility, in

The disintegration and vaporization of plastic targets irradiated by high-power laser pulses

International Nuclear Information System (INIS)

Greig, J.R.; Pechacek, R.E.

1977-01-01

We have studied the disintegration of polyethylene and polystyrene targets irradiated by 100-J 40-nsec Nd/glass laser pulses. At power densities of approximately-less-than10 12 W/cm 2 relatively massive targets (6 x 10 -5 to 5 x 10 -4 cm 3 ) are totally disintegrated to produce finely divided target material and un-ionized vapor. Both the size of the target and the presence or absence of a laser prepulse strongly influence the proportions of finely divided target material and un-ionized vapor, especially within the first few microseconds after peak laser power. This disintegration is always preceded by the emission of a hot fully ionized plasma, but only 1% of the target material is contained in the hot plasma. Typically, (1--3) x 10 19 atoms of un-ionized vapor are released as a slowly expanding (vapprox.10 5 cm/sec) cold dense gas cloud (n/sub o/>10 19 cm -3 ) surrounding the initial target position. This cloud of target material has subsequently been heated by absorption of a 300-J 100-nsec CO 2 laser pulse to produce an approximately fully ionized plasma

Visual observation of boiling in high power liquid target

Energy Technology Data Exchange (ETDEWEB)

Peeples, J. L.; Stokely, M. H.; Poorman, M. C.; Magerl, M.; Wieland, B. W. [Bruce Technologies Inc., 1939 Evans Rd. Cary, NC 27513 (United States); IBA Molecular, 801 Forestwood Dr. Romeoville, IL 60446 (United States); Bruce Technologies Inc., 1939 Evans Rd. Cary, NC 27513 (United States)

2012-12-19

A top pressurized, batch style, 3.15 mL total volume (2.5 mL fill volume) water target with transparent viewing windows was operated on an IBA 18/9 cyclotron at 18 MeV proton energy and beam power up to 1.1 kW. Video recordings documented bubble formation and transport, and blue light from de-excitation of water molecules produced images of proton beam stopping geometry including location of the Bragg peak.

International magnetic pulse compression workshop: (Proceedings)

Energy Technology Data Exchange (ETDEWEB)

Kirbie, H.C.; Newton, M.A.; Siemens, P.D.

1991-04-01

A few individuals have tried to broaden the understanding of specific and salient pulsed-power topics. One such attempt is this documentation of a workshop on magnetic switching as it applies primarily to pulse compression (power transformation), affording a truly international perspective by its participants under the initiative and leadership of Hugh Kirbie and Mark Newton of the Lawrence Livermore National Laboratory (LLNL) and supported by other interested organizations. During the course of the Workshop at Granlibakken, a great deal of information was amassed and a keen insight into both the problems and opportunities as to the use of this switching approach was developed. The segmented workshop format proved ideal for identifying key aspects affecting optimum performance in a variety of applications. Individual groups of experts addressed network and system modeling, magnetic materials, power conditioning, core cooling and dielectrics, and finally circuits and application. At the end, they came together to consolidate their input and formulate the workshop's conclusions, identifying roadblocks or suggesting research projects, particularly as they apply to magnetic switching's trump card--its high-average-power-handling capability (at least on a burst-mode basis). The workshop was especially productive both in the quality and quantity of information transfer in an environment conducive to a free and open exchange of ideas. We will not delve into the organization proper of this meeting, rather we wish to commend to the interested reader this volume, which provides the definitive and most up-to-date compilation on the subject of magnetic pulse compression from underlying principles to current state of the art as well as the prognosis for the future of magnetic pulse compression as a consensus of the workshop's organizers and participants.

International magnetic pulse compression workshop: [Proceedings

International Nuclear Information System (INIS)

Kirbie, H.C.; Newton, M.A.; Siemens, P.D.

1991-04-01

A few individuals have tried to broaden the understanding of specific and salient pulsed-power topics. One such attempt is this documentation of a workshop on magnetic switching as it applies primarily to pulse compression (power transformation), affording a truly international perspective by its participants under the initiative and leadership of Hugh Kirbie and Mark Newton of the Lawrence Livermore National Laboratory (LLNL) and supported by other interested organizations. During the course of the Workshop at Granlibakken, a great deal of information was amassed and a keen insight into both the problems and opportunities as to the use of this switching approach was developed. The segmented workshop format proved ideal for identifying key aspects affecting optimum performance in a variety of applications. Individual groups of experts addressed network and system modeling, magnetic materials, power conditioning, core cooling and dielectrics, and finally circuits and application. At the end, they came together to consolidate their input and formulate the workshop's conclusions, identifying roadblocks or suggesting research projects, particularly as they apply to magnetic switching's trump card--its high-average-power-handling capability (at least on a burst-mode basis). The workshop was especially productive both in the quality and quantity of information transfer in an environment conducive to a free and open exchange of ideas. We will not delve into the organization proper of this meeting, rather we wish to commend to the interested reader this volume, which provides the definitive and most up-to-date compilation on the subject of magnetic pulse compression from underlying principles to current state of the art as well as the prognosis for the future of magnetic pulse compression as a consensus of the workshop's organizers and participants

MOOC Design Workshop

DEFF Research Database (Denmark)

Nørgård, Rikke Toft; Mor, Yishay; Warburton, Steven

2016-01-01

For the last two years we have been running a series of successful MOOC design workshops. These workshops build on previous work in learning design and MOOC design patterns. The aim of these workshops is to aid practitioners in defining and conceptualising educational innovations (predominantly......, but not exclusively MOOCs) which are based on an empathic user-centered view of the target learners and teachers. In this paper, we share the main principles, patterns and resources of our workshops and present some initial results for their effectiveness...

TARG2 Workshop - Slides of the presentations

International Nuclear Information System (INIS)

Malka, V.; Koehler, A.; Beaurepaire, B.; Krishnan, M.; Guillaume, E.; Chowdhury, E.; Volpe, L.; Nakatsutsumi, M.; Chatain, D.; Legare, F.; Wachulak, P.; Bocoum, M.; Leblanc, A.; Schreiber, J.; Ter-Avetisyan, S.; Zeil, K.; Fukuda, Y.; Levecq, X.; Svensson, K.; Mollica, F.; Brandi, F.; Ruiz, C.

2016-01-01

The topics tackled in this workshop involved: laser-plasma interaction, innovative targets from gases to solids, targetry recycling and debris management, mass fabrication of laser targets, high repetition rate capability, integrated plasma diagnostics, wakefield acceleration and radiation sources. This document is made up of the slides of the presentations

16th Workshop on High Energy Spin Physics

CERN Document Server

2016-01-01

The Workshop will cover a wide range of spin phenomena at high and intermediate energies such as: recent experimental data on spin physics the nucleon spin structure and GPD's spin physics and QCD spin physics in the Standard Model and beyond T-odd spin effects polarization and heavy ion physics spin in gravity and astrophysics the future spin physics facilities spin physics at NICA polarimeters for high energy polarized beams acceleration and storage of polarized beams the new polarization technology related subjects The Workshop will be held in the Bogoliubov Laboratory of Theoretical Physics of the Joint Institute for Nuclear Research, 141980 Dubna, Moscow Region, Russia. The program of the workshop will include plenary and parallel (if necessary) sessions. Plenary sessions will be held in the Conference Hall. Parallel sections will take place in the same building. There will be invited talks (up to 40 min) and original reports (20 min). The invited speakers will present new experimental and theoretical re...

Report on high energy neutron dosimetry workshop

International Nuclear Information System (INIS)

Alvar, K.R.; Gavron, A.

1993-01-01

The workshop was called to assess the performance of neutron dosimetry per the responses from ten DOE accelerator facilities to an Office of Energy Research questionnaire regarding implementation of a personnel dosimetry requirement in DRAFT DOE 5480.ACC, ''Safety of Accelerator Facilities''. The goals of the workshop were to assess the state of dosimetry at high energy accelerators and if such dosimetry requires improvement, to reach consensus on how to proceed with such improvements. There were 22 attendees, from DOE Programs and contract facilities, DOE, Office of Energy Research (ER), Office of Environmental Safety and Health (EH), Office of Fusion Energy, and the DOE high energy accelerator facilities. A list of attendees and the meeting agenda are attached. Copies of the presentations are also attached

The Astronomy Workshop

Science.gov (United States)

Hamilton, D. P.; Asbury, M. L.; Proctor, A.

2001-12-01

The Astronomy Workshop (http://janus.astro.umd.edu) is an interactive online astronomy resource developed, and maintained at the University of Maryland, for use by students, educators and the general public. The Astronomy Workshop has been extensively tested and used successfully at many different levels, including High School and Junior High School science classes, University introductory astronomy courses, and University intermediate and advanced astronomy courses. Some topics currently covered in the Astronomy Workshop are: Animated Orbits of Planets and Moons: The orbits of the nine planets and 91 known planetary satellites are shown in animated, to-scale drawings. The orbiting bodies move at their correct relative speeds about their parent, which is rendered as an attractive, to-scale gif image. Solar System Collisions: This most popular of our applications shows what happens when an asteroid or comet with user-defined size and speed impacts a given planet. The program calculates many effects, including the country impacted (if Earth is the target), energy of the explosion, crater size, magnitude of the planetquake generated. It also displays a relevant image (e.g. terrestrial crater, lunar crater, etc.). Planetary and Satellite Data Calculators: These tools allow the user to easily calculate physical data for all of the planets or satellites simultaneously, making comparison very easy. Orbital Simulations: These tools allow the student to investigate different aspects of the three-body problem of celestial mechanics. Astronomy Workshop Bulletin Board: Get innovative teaching ideas and read about in-class experiences with the Astronomy Workshop. Share your ideas with other educators by posting on the Bulletin Board. Funding for the Astronomy Workshop is provided by the National Science Foundation.

HEPVIS96 workshop on visualization in high-energy physics. Proceedings

Energy Technology Data Exchange (ETDEWEB)

Taylor, L; Vandoni, C E [eds.

1997-01-29

This report constitutes the formal proceedings of the HEPVIS96 workshop on visualization in high-energy physics, which was held at CERN from 2nd to 4th of September 1996. The workshop, which is in the HEPVVIS series, covered the topics of event visualization, computer graphics technologies and standards, and data analysis and visualization in high-energy physics. (orig.).

HEPVIS96 workshop on visualization in high-energy physics. Proceedings

International Nuclear Information System (INIS)

Taylor, L.; Vandoni, C.E.

1997-01-01

This report constitutes the formal proceedings of the HEPVIS96 workshop on visualization in high-energy physics, which was held at CERN from 2nd to 4th of September 1996. The workshop, which is in the HEPVVIS series, covered the topics of event visualization, computer graphics technologies and standards, and data analysis and visualization in high-energy physics. (orig.)

Proceedings of the first JAERI-Kansai international workshop on ultrashort-pulse ultrahigh-power lasers and simulation for laser-plasma interactions

International Nuclear Information System (INIS)

1998-03-01

Records of the First JAERI-Kansai International Workshop, which focused on the subject of 'Ultrashort-Pulse Ultrahigh-Power Lasers and Simulation for Laser-Plasma Interactions', are contained in this issue. The First JAERI-Kansai International Workshop was held as Joint ICFA/JAERI-Kansai International Workshop '97 with International Committee for Future Accelerators (ICFA). This report consists of 24 contributed papers. (J.P.N.)

Proceedings of the first JAERI-Kansai international workshop on ultrashort-pulse ultrahigh-power lasers and simulation for laser-plasma interactions

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Records of the First JAERI-Kansai International Workshop, which focused on the subject of `Ultrashort-Pulse Ultrahigh-Power Lasers and Simulation for Laser-Plasma Interactions`, are contained in this issue. The First JAERI-Kansai International Workshop was held as Joint ICFA/JAERI-Kansai International Workshop `97 with International Committee for Future Accelerators (ICFA). This report consists of 24 contributed papers. (J.P.N.)

77 FR 9273 - WORKSHOP Sponsored by the Nuclear Regulatory Commission and the Electric Power Research Institute...

Science.gov (United States)

2012-02-16

... Commission and the Electric Power Research Institute on the Treatment of Probabilistic Risk Assessment.... SUMMARY: The U.S. Nuclear Regulatory Commission (NRC), Office of Nuclear Regulatory Research (RES), in cooperation with the Electric Power Research Institute (EPRI), will hold a joint workshop on the Treatment of...

High-Speed Research: 1994 Sonic Boom Workshop. Configuration, Design, Analysis and Testing

Science.gov (United States)

McCurdy, David A. (Editor)

1999-01-01

The third High-Speed Research Sonic Boom Workshop was held at NASA Langley Research Center on June 1-3, 1994. The purpose of this workshop was to provide a forum for Government, industry, and university participants to present and discuss progress in their research. The workshop was organized into sessions dealing with atmospheric propagation; acceptability studies; and configuration design, and testing. Attendance at the workshop was by invitation only. The workshop proceedings include papers on design, analysis, and testing of low-boom high-speed civil transport configurations and experimental techniques for measuring sonic booms. Significant progress is noted in these areas in the time since the previous workshop a year earlier. The papers include preliminary results of sonic boom wind tunnel tests conducted during 1993 and 1994 on several low-boom designs. Results of a mission performance analysis of all low-boom designs are also included. Two experimental methods for measuring near-field signatures of airplanes in flight are reported.

Simulation of beam pointing stability on targeting plane of high power excimer laser system

International Nuclear Information System (INIS)

Wang Dahui; Zhao Xueqing; Zhang Yongsheng; Zheng Guoxin; Hu Yun; Zhao Jun

2011-01-01

Based on characteristics of image-relaying structure in high power excimer MOPA laser system, simulation and analysis software of targeting beam's barycenter stability was designed by using LABVIEW and MATLAB. Simulation was made to measured results of every optical component in laboratory environment. Simulation and validation of budget values for optical components was and optimization of error budget of system was accomplished via post-allocation for several times. It is shown that targeting beam's barycenter stability in the condition of current laboratory environment can't satisfy needs and index of high demand optical components can be allotted to 1.7 μrad when index of low demand optical components have some stability margin. These results can provide a guide to construction of system and design and machining of optical components and optimization of system. Optical components of laboratory on work can satisfy optimized distributed index, which reduce the demand of structure to some extent. (authors)

Proceedings of JSPS-CAS core university program seminar on target materials

International Nuclear Information System (INIS)

Gu, Z.Z.; Norimatsu, T.

2008-02-01

China-Japan Bilateral Collaboration on the Study of Ultrahigh Density Plasma has been established since 2001 and its second phase is conducting from 2006. Target materials are key issue of the Study of Ultrahigh Density Plasma, and the second of target fabrication was opened at the 2005 Workshop on Ultrahigh Density Plasma Production, Application and theory for Laser Fusion at Nine Village Valley, Sichuan. It achieved great successes in high-level academic exchange and efficient presentation of state-of-the-art development in this research field. However, in order to attract greater attention and participation of more scientists in these fields, the organizing committee decided to further specify and enlarge the scale of the workshop to be China-Japan Bilateral Seminar on Target Materials 2007 in Huang Shan in southern Anhui Province of east China. The seminar had more than 20 participants from 7 universities and 3 institutes in Japan and China. They exchanged state-of-the-art development in nanomaterials, capsule fabrication and low density materials toward target of high power laser. This issue is the collection of the paper presented at the seminar. The 17 of the presented papers are indexed individually. (J.P.N.)

12th Advanced Accelerator Concept (AAC 2006) Workshop

International Nuclear Information System (INIS)

Piot, Philippe

2006-01-01

Summary of the 12th Advanced Accelerator Concept (AAC 2006) Workshop help by NIU and ANL on July 10th-15th 2006 in Lake Geneva WI. The proceedings of the workshop have been published as an AIP conference proceedings '12th Advanced Accelerator Concepts Workshop' volume 877. The Twelfth Workshop on Advanced Accelerator Concepts was held at the Grand Geneva Resort in Lake Geneva, Wisconsin, from July 10 to July 15, 2006. The Workshop was sponsored by the High Energy Physics program of the U.S. Department of Energy, and was hosted by the Argonne Wakefield Accelerator Group (AWA) of Argonne National Laboratory and by Northern Illinois University. The workshop is a bi-annual meeting among physicist working on novel charged particle acceleration concept. The name 'advanced accelerator' physics covers long term research and development in beam physics and accelerator technologies. Some of the topics in advanced accelerator R and D are laser acceleration of electrons, wake field acceleration, novel high power rf source, new beam diagnostics, free-electron lasers, generating high brightness electron beams etc. The Advanced Accelerator Concept workshop is the only acknowledged and fully sponsored forum that provides a platform for inter- and cross-disciplinary discussion on various aspects of advanced accelerator and beam physics/technology concepts.

Proceedings of the third ICFA mini-workshop on high intensity, high brightness hadron accelerators

International Nuclear Information System (INIS)

Roser, T.

1997-01-01

The third mini-workshop on high intensity, high brightness hadron accelerators was held at Brookhaven National Laboratory on May 7-9, 1997 and had about 30 participants. The workshop focussed on rf and longitudinal dynamics issues relevant to intense and/or bright hadron synchrotrons. A plenary session was followed by four sessions on particular topics. This document contains copies of the viewgraphs used as well as summaries written by the session chairs

Report on the ESO Workshop ''Astronomy at High Angular Resolution''

Science.gov (United States)

Boffin, H.; Schmidtobreick, L.; Hussain, G.; Berger, J.-Ph.

2015-03-01

A workshop took place in Brussels in 2000 on astrotomography, a generic term for indirect mapping techniques that can be applied to a huge variety of astrophysical systems, ranging from planets, single stars and binaries to active galactic nuclei. It appeared to be timely to revisit the topic given the many past, recent and forthcoming improvements in telescopes and instrumentation. We therefore decided to repeat the astrotomography workshop, but to put it into the much broader context of high angular resolution astronomy. Many techniques, from lucky and speckle imaging, adaptive optics to interferometry, are now widely employed to achieve high angular resolution and they have led to an amazing number of new discoveries. A summary of the workshop themes is presented.

76 FR 20690 - International Consortium of Orthopedic Registries; Public Workshop

Science.gov (United States)

2011-04-13

... is the target audience for this public workshop? Who should attend this public workshop? This workshop is open to all interested parties. The target audience is comprised of data holders, researchers...

Power and the objectification of social targets.

Science.gov (United States)

Gruenfeld, Deborah H; Inesi, M Ena; Magee, Joe C; Galinsky, Adam D

2008-07-01

Objectification has been defined historically as a process of subjugation whereby people, like objects, are treated as means to an end. The authors hypothesized that objectification is a response to social power that involves approaching useful social targets regardless of the value of their other human qualities. Six studies found that under conditions of power, approach toward a social target was driven more by the target's usefulness, defined in terms of the perceiver's goals, than in low-power and baseline conditions. This instrumental response to power, which was linked to the presence of an active goal, was observed using multiple instantiations of power, different measures of approach, a variety of goals, and several types of instrumental and noninstrumental target attributes. Implications for research on the psychology of power, automatic goal pursuit, and self-objectification theory are discussed.

CEBAF/SURA 1985 Summer Workshop

International Nuclear Information System (INIS)

Crannel, H.

1985-12-01

The 1985 Summer Workshop began a new phase of planning for the experimental program at CEBAF. One goal of the Workshop was to define and describe options for equipping the CEBAF and stations with experimental equipment. Starting with an initial list of options which grew out of discussions during the Winter of 1984 and the Spring of 1985, the five working groups met during the Workshop and developed their final reports, included in these proceedings. The program of the Workshop consisted of invited talks on both theoretical and experimental topics, and working group meetings. The five working groups, include: Magnetic Spectrometers; Large Acceptance Detectors and Low Intensity Beams; Internal Targets; Positrons; Theory. These proceedings begin with an overview of CEBAF, and a report on progress made by the Magnetic Spectrometer and Internal Target Working Groups prior to the Workshop. The next part contains the invited talks, presented in the order which they were given during the week. The final reports of the five working groups follow this, and the proceedings conclude with papers contributed to the Workshop

Workshop on high-resolution, large-acceptance spectrometers

Energy Technology Data Exchange (ETDEWEB)

Zeidman, B. (ed.)

1981-01-01

The purpose of the Workshop on High-Resolution, Large-Acceptance Spectrometers was to provide a means for exchange of information among those actively engaged in the design and construction of these new spectrometers. Thirty-seven papers were prepared for the data base.

Post-Irradiation Properties of Candidate Materials for High-Power Targets

International Nuclear Information System (INIS)

Kirk, H.G.; Ludewig, H.; Mausner, L.F.; Simos, N.; Thieberger, P.; Brookhaven; Hayato, Y.; Yoshimura, K.; McDonald, K.T.; Sheppard, J.; Trung, L.P.

2006-01-01

The desire of the high-energy-physics community for more intense secondary particle beams motivates the development of multi-megawatt, pulsed proton sources. The targets needed to produce these secondary particle beams must be sufficiently robust to withstand the intense pressure waves arising from the high peak-energy deposition which an intense pulsed beam will deliver. In addition, the materials used for the targets must continue to perform in a severe radiation environment. The effect of the beam-induced pressure waves can be mitigated by use of target materials with high-yield strength and/or low coefficient of thermal expansion (CTE) [1, 2, 3]. We report here first results of an expanded study of the effects of irradiation on several additional candidate materials with high strength (AlBeMet, beryllium, Ti-V6-Al4) or low CTE (a carbon-carbon composite, a new Toyota ''gum'' metal alloy [4], Super-Invar)

Energy and nuclear power planning using the IAEA's ENPEP computer package. Proceedings of a workshop

International Nuclear Information System (INIS)

1997-09-01

The Regional (Europe) Technical Co-operation Project on the Study of Energy Options Using the IAEA Planning Methodologies was first implemented by the IAEA in 1995. The project aims at improving national capabilities for energy, electricity and nuclear power planning and promoting regional co-operation among participating countries in the European region. The project includes the organization of workshops, training activities at the regional and national levels, scientific visits, etc. The proceedings of a workshop held in Warsaw, Poland, from 4 to 8 September 1995 are contained herein. The workshop had as a basic objective the analysis of the specific problems encountered by the represented countries during application of the IAEA's ENPEP package in the conduct of national studies and to provide a forum for further co-operation among participating countries. A second objective of the workshop was to make proposals for future activities to be organized within the project. This publication is intended to serve as reference for the users of the IAEA's ENPEP package, as well as for energy and electricity planners in general. Refs, figs, tabs

A flexible testing facility for high-power targets (Tiara FP7 program)

CERN Document Server

Fusco, Y.; Samec, K.; Kadi, Y.

2014-01-01

Building on recent experience in the field of applied physics, TIARA Work package n° 9 focuses on target applications for accelerators in Europe. A roadmap for target development has been derived from major achievements in the EU-FP6 and EU-FP7 programs such as the MEGAPIE and EURISOL experiments. The TIARA management board concluded that a worthwhile continuation of such projects would be in the development of a flexible material irradiation facility easily transportable and which could be installed in different laboratories. The power is limited to 100 kW in a very compact arrangement so as to obtain the best neutron economy from a moderate beam power which is more likely to be found in laboratories across Europe. The challenges posed by such a compact design and accompanying calculations are presented in the current work.

Technology and Components of Accelerator-driven Systems. Second International Workshop Proceedings, Nantes, France, 21-23 May 2013

International Nuclear Information System (INIS)

2015-01-01

The accelerator-driven system (ADS) is a potential transmutation system option as part of partitioning and transmutation strategies for radioactive waste in advanced nuclear fuel cycles. Following the success of the workshop series on the utilisation and reliability of the High Power Proton Accelerators (HPPA), the scope of this new workshop series on Technology and Components of Accelerator-driven Systems has been extended to cover subcritical systems as well as the use of neutron sources. The workshop organised by the OECD Nuclear Energy Agency provided experts with a forum to present and discuss state-of-the-art developments in the field of ADS and neutron sources. A total of 40 papers were presented during the oral and poster sessions. Four technical sessions were organised addressing ADS experiments and test facilities, accelerators, simulation, safety, data, neutron sources that were opportunity to present the status of projects like the MYRRHA facility, the MEGAPIE target, FREYA and GUINEVERE experiments, the KIPT neutron source, and the FAIR linac. These proceedings include all the papers presented at the workshop

Low power multiple shell fusion targets for use with electron and ion beams

International Nuclear Information System (INIS)

Lindl, J.D.; Bangerter, R.O.

1975-01-01

Use of double shell targets with a separate low Z, low density ablator at large radius for the outer shell, reduces the focusing and power requirements while maintaining reasonable aspect ratios. A high Z, high density pusher shell is placed at a much smaller radius in order to obtain an aspect ratio small enough to protect against fluid instability. Velocity multiplication between these shells further lowers the power requirements. Careful tuning of the power profile and intershell density results in a low entropy implosion which allows breakeven at low powers. Ion beams appear to be a promising power source and breakeven at 10-20 Terrawatts with 10 MeV alpha particles appears feasible. Predicted performance of targets with various energy sources is shown and comparison is made with single shell targets

1995 second modulator-klystron workshop: A modulator-klystron workshop for future linear colliders

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This second workshop examined the present state of modulator design and attempted an extrapolation for future electron-positron linear colliders. These colliders are currently viewed as multikilometer-long accelerators consisting of a thousand or more RF sources with 500 to 1,000, or more, pulsed power systems. The workshop opened with two introductory talks that presented the current approaches to designing these linear colliders, the anticipated RF sources, and the design constraints for pulse power. The cost of main AC power is a major economic consideration for a future collider, consequently the workshop investigated efficient modulator designs. Techniques that effectively apply the art of power conversion, from the AC mains to the RF output, and specifically, designs that generate output pulses with very fast rise times as compared to the flattop. There were six sessions that involved one or more presentations based on problems specific to the design and production of thousands of modulator-klystron stations, followed by discussion and debate on the material.

Extended abstracts of the 12th JAERI workshop on high-Tc superconductors

Energy Technology Data Exchange (ETDEWEB)

Hojou, Kiichi; Okayasu, Satoru; Sasase, Masato [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Ishida, Takekazu [Osaka Prefectual Univ., Sakai (JP)] (eds.)

2001-03-01

This workshop was held on December 7-8, 2000 at JAERI (Tokai). The research group at JAERI shares a responsibility for material modification of high-Tc superconductors by irradiation in 'the multi-core project II of the high temperature superconducting material research' organized by STA (Science and Technology Agency) of Japan. This report contains the extended abstracts of workshop presentations covering basic theories, various experimental results and material improvement studies of the superconductivity by high energy ion irradiation. The twelve presentations of the workshop were devoted to a mini symposium where the direct observations of vortices were discussed in view of the various sophisticated techniques. (author)

Extended abstracts of the 12th JAERI workshop on high-Tc superconductors

International Nuclear Information System (INIS)

Hojou, Kiichi; Okayasu, Satoru; Sasase, Masato

2001-03-01

This workshop was held on December 7-8, 2000 at JAERI (Tokai). The research group at JAERI shares a responsibility for material modification of high-Tc superconductors by irradiation in 'the multi-core project II of the high temperature superconducting material research' organized by STA (Science and Technology Agency) of Japan. This report contains the extended abstracts of workshop presentations covering basic theories, various experimental results and material improvement studies of the superconductivity by high energy ion irradiation. The twelve presentations of the workshop were devoted to a mini symposium where the direct observations of vortices were discussed in view of the various sophisticated techniques. (author)

Target studies for the neutrino factory at the Rutherford Appleton laboratory

CERN Document Server

Drumm, P V; Bennett, R

2001-01-01

Target studies at the Rutherford Appleton Laboratory have concentrated on studies of a solid heavy metal target. The suggestion to use a radiatively cooled target which rotates in beam was made shortly after the first NuFact workshop as a means of dissipating large amounts of power at a high temperature, and as an alternative to the proposed water-cooled rotating band and liquid metal jet targets. This paper examines the proposed drive scheme for the target ring, which uses induced currents and magnetic forces to both levitate and drive the target. Estimates of the power required to levitate and drive the target ring and the forces exerted on the moving ring as it enters the target capture solenoid are given. One of the principle concerns in the operation of a solid target is the severe shock stress experienced due to the impact of an intense energetic proton beam in a short time compared to the transit time of sound in the material. Calculations of the stresses induced in the target ring and their evolution ...

Workshop on nuclear structure at moderate and high spin: Slide report

International Nuclear Information System (INIS)

1986-10-01

The workshop was scheduled to coincide with the beginning of operation of a number of large arrays of Compton-suppressed germanium detectors. The workshop was divided into 14 sessions containing 3 presentations each. The topics of these sessions were superdeformation, heavy rare earths, single-particle configurations, band termination, continuum properties, light rare-earths, new techniques, high temperatures, transfer reactions, transition region, shapes, lifetimes, and moments. This publication consists of the slides used in all of the presentations at the workshop

Academic excellence workshops in chemistry and physics

Science.gov (United States)

Mills, Susan Rose

In the mid-1970's, Uri Treisman, at the University of California, Berkeley, developed an academic excellence workshop program that had important successes in increasing minority student achievement and persistence in calculus. The present dissertation research is an in-depth study of chemistry and physics workshops at the California State Polytechnic University, Pomona. Data for the first, longitudinal component of this study were obtained by tracking to Spring 1998 all workshop minority students, i.e., Latino, African American, and Native American workshop students, a random sample of non-workshop minority students, and a random sample of non-targeted students, i.e., Anglo and Asian students, enrolled in first-quarter General Chemistry or Physics during specific quarters of 1992 or 1993. Data for the second component were obtained by administering questionnaires, conducting interviews, and observing science students during Fall, 1996. Workshop participation was a significant predictor of first-quarter course grade for minority students in both chemistry and physics, while verbal and mathematics Scholastic Aptitude Test (SAT) scores were not significant predictors of beginning course grade for minority science students. The lack of predictive ability of the SAT and the importance of workshop participation in minority students' beginning science course performance are results with important implications for educators and students. In comparing pre-college achievement measures for workshop and non-targeted students, non-targeted students' mathematics SAT scores were significantly higher than chemistry and physics workshop students' scores. Nonetheless, workshop participation "leveled the field" as workshop and non-targeted students performed similarly in beginning science courses. Positive impacts of workshop participation on achievement, persistence, efficiency, social integration, and self-confidence support the continued and expanded funding of workshop programs

8th international workshop on large-scale integration of wind power into power systems as well as on transmission networks for offshore wind farms. Proceedings

International Nuclear Information System (INIS)

Betancourt, Uta; Ackermann, Thomas

2009-01-01

Within the 8th International Workshop on Large-Scale Integration of Wind Power into Power Systems as well as on Transmission Networks for Offshore Wind Farms at 14th to 15th October, 2009 in Bremen (Federal Republic of Germany), lectures and posters were presented to the following sessions: (1) Keynote session and panel; (2) Grid integration studies and experience: Europe; (3) Connection of offshore wind farms; (4) Wind forecast; (5) High voltage direct current (HVDC); (6) German grid code issues; (7) Offshore grid connection; (8) Grid integration studies and experience: North America; (9) SUPWIND - Decision support tools for large scale integration of wind; (10) Windgrid - Wind on the grid: An integrated approach; (11) IEA Task 25; (12) Grid code issues; (13) Market Issues; (14) Offshore Grid; (15) Modelling; (16) Wind power and storage; (17) Power system balancing; (18) Wind turbine performance; (19) Modelling and offshore transformer.

High performance inertial fusion targets

International Nuclear Information System (INIS)

Nuckolls, J.H.; Bangerter, R.O.; Lindl, J.D.; Mead, W.C.; Pan, Y.L.

1977-01-01

Inertial confinement fusion (ICF) designs are considered which may have very high gains (approximately 1000) and low power requirements (<100 TW) for input energies of approximately one megajoule. These include targets having very low density shells, ultra thin shells, central ignitors, magnetic insulation, and non-ablative acceleration

Workshop on Non-Imaging Cherenkov at High Energy

CERN Document Server

2013-01-01

The non-Imaging Cherenkov air shower measurement technique holds great promise in furthering our understanding the Knee-to-Ankle region of the cosmic ray spectrum. In particular, this technique offers a unique way to determine the evolution of the cosmic ray nuclear composition, and an example is given by the recent spectrum results of the Tunka Collaboration. With this in mind, we are organizing a workshop, to be held at the University of Utah, to bring together the various practitioners of this cosmic ray measurement technique to share simulations, analyses, detector designs, and past experimental results amongst the community. The workshop will also be in support of our effort, NICHE, to extend the reach of the TA/TALE detector systems down to the Knee. We anticipate that the workshop will result in a white paper on the scientific importance of these high-energy cosmic ray measurements and on using the Cherenkov technique to accomplish them. Our goal is to have contributions from members of the previous ge...

Summary Report of Advanced Hydropower Innovations and Cost Reduction Workshop at Arlington, VA, November 5 & 6, 2015

Energy Technology Data Exchange (ETDEWEB)

O' Connor, Patrick [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Rugani, Kelsey [Kearns & West, Inc., San Francisco, CA (United States); West, Anna [Kearns & West, Inc., San Francisco, CA (United States)

2016-03-01

On behalf of the U.S. Department of Energy (DOE) Wind and Water Power Technology Office (WWPTO), Oak Ridge National Laboratory (ORNL), hosted a day and half long workshop on November 5 and 6, 2015 in the Washington, D.C. metro area to discuss cost reduction opportunities in the development of hydropower projects. The workshop had a further targeted focus on the costs of small, low-head1 facilities at both non-powered dams (NPDs) and along undeveloped stream reaches (also known as New Stream-Reach Development or “NSD”). Workshop participants included a cross-section of seasoned experts, including project owners and developers, engineering and construction experts, conventional and next-generation equipment manufacturers, and others to identify the most promising ways to reduce costs and achieve improvements for hydropower projects.

Biogas and Fuel Cells Workshop Summary Report: Proceedings from the Biogas and Fuel Cells Workshop, Golden, Colorado, June 11-13, 2012

Energy Technology Data Exchange (ETDEWEB)

2013-01-01

The U.S. Department of Energy (DOE) National Renewable Energy Laboratory (NREL) held a Biogas and Fuel Cells Workshop June 11-13, 2012, in Golden, Colorado, to discuss biogas and waste-to-energy technologies for fuel cell applications. The overall objective was to identify opportunities for coupling renewable biomethane with highly efficient fuel cells to produce electricity; heat; combined heat and power (CHP); or combined heat, hydrogen and power (CHHP) for stationary or motive applications. The workshop focused on biogas sourced from wastewater treatment plants (WWTPs), landfills, and industrial facilities that generate or process large amounts of organic waste, including large biofuel production facilities (biorefineries).

10th International Workshop on Parallel Tools for High Performance Computing

CERN Document Server

Gracia, José; Hilbrich, Tobias; Knüpfer, Andreas; Resch, Michael; Nagel, Wolfgang

2017-01-01

This book presents the proceedings of the 10th International Parallel Tools Workshop, held October 4-5, 2016 in Stuttgart, Germany – a forum to discuss the latest advances in parallel tools. High-performance computing plays an increasingly important role for numerical simulation and modelling in academic and industrial research. At the same time, using large-scale parallel systems efficiently is becoming more difficult. A number of tools addressing parallel program development and analysis have emerged from the high-performance computing community over the last decade, and what may have started as collection of small helper script has now matured to production-grade frameworks. Powerful user interfaces and an extensive body of documentation allow easy usage by non-specialists.

Characterization of a plasma produced using a high power laser with a gas puff target for x-ray laser experiments

International Nuclear Information System (INIS)

Fiedorowicz, H.; Bartnik, A.; Gac, K.; Parys, P.; Szczurek, M.; Tyl, J.

1995-01-01

A high temperature, high density plasma can be produced by using a nanosecond, high-power laser with a gas puff target. The gas puff target is formed by puffing a small amount of gas from a high-pressure reservoir through a nozzle into a vacuum chamber. In this paper we present the gas puff target specially designed for x-ray laser experiments. The solenoid valve with the nozzle in the form of a slit 0.3-mm wide and up to 40-mm long, allows to form an elongated gas puff suitable for the creation of an x-ray laser active medium by its perpendicular irradiation with the use of a laser beam focused to a line. Preliminary results of the experiments on the laser irradiation of the gas puff targets, produced by the new valve, show that hot plasma suitable for x-ray lasers is created

Measurement of electromagnetic pulses generated during interactions of high power lasers with solid targets

International Nuclear Information System (INIS)

De Marco, M.; Krása, J.; Margarone, D.; Giuffrida, L.; Vrana, R.; Velyhan, A.; Korn, G.; Weber, S.; Cikhardt, J.; Pfeifer, M.; Krouský, E.; Ullschmied, J.; Ahmed, H.; Borghesi, M.; Kar, S.; Limpouch, J.; Velardi, L.; Side, D. Delle; Nassisi, V.

2016-01-01

A target irradiated with a high power laser pulse, blows off a large amount of charge and as a consequence the target itself becomes a generator of electromagnetic pulses (EMP) owing to high return current flowing to the ground through the target holder. The first measurement of the magnetic field induced by the neutralizing current reaching a value of a few kA was performed with the use of an inductive target probe at the PALS Laser Facility (Cikhardt et al. Rev. Sci. Instrum. 85 (2014) 103507). A full description of EMP generation should contain information on the spatial distribution and temporal variation of the electromagnetic field inside and outside of the interaction chamber. For this reason, we consider the interaction chamber as a resonant cavity in which different modes of EMP oscillate for hundreds of nanoseconds, until the EMP is transmitted outside through the glass windows and EM waves are attenuated. Since the experimental determination of the electromagnetic field distribution is limited by the number of employed antennas, a mapping of the electromagnetic field has to be integrated with numerical simulations. Thus, this work reports on a detailed numerical mapping of the electromagnetic field inside the interaction chamber at the PALS Laser Facility (covering a frequency spectrum from 100 MHz to 3 GHz) using the commercial code COMSOL Multiphysics 5.2. Moreover we carried out a comparison of the EMP generated in the parallelepiped-like interaction chamber used in the Vulcan Petawatt Laser Facility at the Rutherford Appleton Laboratory, against that produced in the spherical interaction chamber of PALS.

Atomic Beam Merging and Suppression of Alkali Contaminants in Multi Body High Power Targets: Design and Test of Target and Ion Source Prototypes at ISOLDE

CERN Document Server

Bouquerel, Elian J A; Lettry, J; Stora, T

2009-01-01

The next generation of high power ISOL-facilities will deliver intense and pure radioactive ion beams. Two key issues of developments mandatory for the forthcoming generation of ISOL target-ion source units are assessed and demonstrated in this thesis. The design and production of target and ion-source prototypes is described and dedicated measurements at ISOLDE-CERN of their radioisotope yields are analyzed. The purity of short lived or rare radioisotopes suffer from isobaric contaminants, notably alkalis which are highly volatile and easily ionized elements. Therefore, relying on their chemical nature, temperature controlled transfer lines were equipped with a tube of quartz that aimed at trapping these unwanted elements before they reached the ion source. The successful application yields high alkali-suppression factors for several elements (ie: 80, 82mRb, 126, 142Cs, 8Li, 46K, 25Na, 114In, 77Ga, 95, 96Sr) for quartz temperatures between 300ºC and 1100ºC. The enthalpies of adsorption on quartz were measu...

Final technical report. 1998 HU CFRT summer fusion high school workshop

International Nuclear Information System (INIS)

Ali, Halima; Punjabi, Alkesh

1999-01-01

The center conducted its third High School Summer Fusion Science Workshop in Summer 1998. The center had only three faculty mentors available only for a part of Summer 1998, The center accepted four scholars in this workshop, Prof. Halima Ali coordinated this workshop. Each student was assigned to a research mentor according to the student's interest in a specific research area and problem. In the workshop in the center, the students received instructions and training in the basics of energy, plasma and fusion sciences. They also received one-on-one instructions and training by their mentors to further their understanding of the subject and to introduce to relevant concepts such as magnetic confinement fusion, tokamaks, diverters and area-preserving maps

Energy and nuclear power planning using the IAEA`s ENPEP computer package. Proceedings of a workshop

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-09-01

The Regional (Europe) Technical Co-operation Project on the Study of Energy Options Using the IAEA Planning Methodologies was first implemented by the IAEA in 1995. The project aims at improving national capabilities for energy, electricity and nuclear power planning and promoting regional co-operation among participating countries in the European region. The project includes the organization of workshops, training activities at the regional and national levels, scientific visits, etc. The proceedings of a workshop held in Warsaw, Poland, from 4 to 8 September 1995 are contained herein. The workshop had as a basic objective the analysis of the specific problems encountered by the represented countries during application of the IAEA`s ENPEP package in the conduct of national studies and to provide a forum for further co-operation among participating countries. A second objective of the workshop was to make proposals for future activities to be organized within the project. This publication is intended to serve as reference for the users of the IAEA`s ENPEP package, as well as for energy and electricity planners in general. Refs, figs, tabs.

76 FR 70721 - Voltage Coordination on High Voltage Grids; Notice of Staff Workshop

Science.gov (United States)

2011-11-15

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. AD12-5-000] Voltage Coordination on High Voltage Grids; Notice of Staff Workshop Take notice that the Federal Energy Regulatory Commission will hold a Workshop on Voltage Coordination on High Voltage Grids on Thursday, December 1, 2011...

Instrumentation for the advanced high-flux reactor workshop: proceedings

International Nuclear Information System (INIS)

Moon, R.M.

1984-01-01

The purpose of the Workshop on Instrumentation for the Advanced High-Flux Reactor, held on May 30, 1984, at the Oak Ridge National Laborattory, was two-fold: to announce to the scientific community that ORNL has begun a serious effort to design and construct the world's best research reactor, and to solicit help from the scientific community in planning the experimental facilities for this reactor. There were 93 participants at the workshop. We are grateful to the visiting scientists for their enthusiasm and interest in the reactor project. Our goal is to produce a reactor with a peak thermal flux in a large D 2 O reflector of 5 x 10 15 n/cm 2 s. This would allow the installation of unsurpassed facilities for neutron beam research. At the same time, the design will provide facilities for isotope production and materials irradiation which are significantly improved over those now available at ORNL. This workshop focussed on neutron beam facilities; the input from the isotope and materials irradiation communities will be solicited separately. The reactor project enjoys the full support of ORNL management; the present activities are financed by a grant of $663,000 from the Director's R and D Fund. However, we realize that the success of the project, both in realization and in use of the reactor, depends on the support and imagination of a broad segment of the scientific community. This is more a national project than an ORNL project. The reactor would be operated as a national user facility, open to any research proposal with high scientific merit. It is therefore important that we maintain a continuing dialogue with outside scientists who will be the eventual users of the reactor and the neutron beam facilities. The workshop was the first step in establishing this dialogue; we anticipate further workshops as the project continues

Reactor experiments, workshops, and human resource development education simulating the Great East Japan Earthquake

International Nuclear Information System (INIS)

Horiguchi, Tetsuo; Yamamoto, Tomosada

2012-01-01

Kinki University Atomic Energy Research Institute has been implementing a social education program such as reactor experiments and training sessions for junior and senior high school teachers since 1987, and in recent years, it has been implementing an education program for common citizens. However, the Great East Japan Earthquake has made it necessary to consider not only the dissemination of accurate knowledge, but also responding to the anxiety on nuclear power. This paper explains the contents of the social contribution activities and workshops conducted at Kinki University Atomic Energy Research Institute, after the Great East Japan Earthquake and the Fukushima Daiichi Nuclear Power Station accident. As the activities that are carried out in addition to training sessions, it introduces the implementation state of telephone consultation about nuclear power, and earthquake reconstruction assistance advisory at Kawamata Town, Date-gun, Fukushima Prefecture. As workshop support, it reports human resource development education in the nuclear field at the university, activities at the workshops for junior/senior high school teachers and general public, and questionnaire survey at the time of the workshops. (A.O.)

High-power sputtering employed for film deposition

International Nuclear Information System (INIS)

Shapovalov, V I

2017-01-01

The features of high-power magnetron sputtering employed for the films’ deposition are reviewed. The main physical phenomena accompanying high-power sputtering including ion-electron emission, gas rarefaction, ionization of sputtered atoms, self-sputtering, ion sound waves and the impact of the target heating are described. (paper)

High current proton linear accelerators and nuclear power

International Nuclear Information System (INIS)

Tunnicliffe, P.R.; Chidley, B.G.; Fraser, J.S.

1976-01-01

This paper outlines a possible role that high-current proton linear accelerators might play as ''electrical breeders'' in the forthcoming nuclear-power economy. A high-power beam of intermediate energy protons delivered to an actinide-element target surrounded by a blanket of fertile material may produce fissile material at a competitive cost. Criteria for technical performance and, in a Canadian context, for costs are given and the major problem areas outlined not only for the accelerator and its associated rf power source but also for the target assembly. (author)

Proceedings of Brookhaven National Laboratory's fusion/synfuel workshop

International Nuclear Information System (INIS)

Fillo, J.A.; Powell, J.R.

1979-01-01

The fusion synfuels workshop held at Brookhaven National Laboratory (BNL) on August 27-29, 1979 examined the current status of candidate synfuel processes and the R and D required to develop the capability for fusion synfuel production. Participants divided into five working groups, covering the following areas: (1) economics and applications; (2) high-temperature electrolysis; (3) thermochemical processes (including hybrid thermo-electrochemical); (4) blanket and materials; and (5) high-efficiency power cycles. Each working group presented a summary of their conclusions and recommendations to all participants during the third day of the Workshop. These summaries are given

Planetary Science Education - Workshop Concepts for Classrooms and Internships

Science.gov (United States)

Musiol, S.; Rosenberg, H.; Rohwer, G.; Balthasar, H.; van Gasselt, S.

2014-12-01

In Germany, education in astronomy and planetary sciences is limited to very few schools or universities and is actively pursued by only selected research groups. Our group is situated at the Freie Universität Berlin and we are actively involved in space missions such as Mars Express, Cassini in the Saturnian system, and DAWN at Vesta and Ceres. In order to enhance communication and establish a broader basis for building up knowledge on our solar-system neighborhood, we started to offer educational outreach in the form of workshops for groups of up to 20 students from primary/middle schools to high schools. Small group sizes guarantee practical, interactive, and dialog-based working environments as well as a high level of motivation. Several topical workshops have been designed which are targeted at different age groups and which consider different educational background settings. One workshop called "Impact craters on planets and moons" provides a group-oriented setting in which 3-4 students analyze spacecraft images showing diverse shapes of impact craters on planetary surfaces. It is targeted not only at promoting knowledge about processes on planetary surfaces but it also stimulates visual interpretation skills, 3D viewing and reading of map data. A second workshop "We plan a manned mission to Mars" aims at fostering practical team work by designing simple space mission scenarios which are solved within a team by collaboration and responsibility. A practical outdoor activity called "Everything rotates around the Sun" targets at developing a perception of absolute - but in particular relative - sizes, scales and dimensions of objects in our solar system. Yet another workshop "Craters, volcanoes and co. - become a geologist on Mars" was offered at the annual national "Girls' Day" aiming at motivating primary to middle school girls to deal with topics in classical natural sciences. Small groups investigated and interpreted geomorphologic features in image data of

Flywheel energy storage workshop

Energy Technology Data Exchange (ETDEWEB)

O`Kain, D.; Carmack, J. [comps.

1995-12-31

Since the November 1993 Flywheel Workshop, there has been a major surge of interest in Flywheel Energy Storage. Numerous flywheel programs have been funded by the Advanced Research Projects Agency (ARPA), by the Department of Energy (DOE) through the Hybrid Vehicle Program, and by private investment. Several new prototype systems have been built and are being tested. The operational performance characteristics of flywheel energy storage are being recognized as attractive for a number of potential applications. Programs are underway to develop flywheels for cars, buses, boats, trains, satellites, and for electric utility applications such as power quality, uninterruptible power supplies, and load leveling. With the tremendous amount of flywheel activity during the last two years, this workshop should again provide an excellent opportunity for presentation of new information. This workshop is jointly sponsored by ARPA and DOE to provide a review of the status of current flywheel programs and to provide a forum for presentation of new flywheel technology. Technology areas of interest include flywheel applications, flywheel systems, design, materials, fabrication, assembly, safety & containment, ball bearings, magnetic bearings, motor/generators, power electronics, mounting systems, test procedures, and systems integration. Information from the workshop will help guide ARPA & DOE planning for future flywheel programs. This document is comprised of detailed viewgraphs.

Effects of target bias voltage on indium tin oxide films deposited by high target utilisation sputtering

International Nuclear Information System (INIS)

Calnan, Sonya; Upadhyaya, Hari M.; Dann, Sandra E.; Thwaites, Mike J.; Tiwari, Ayodhya N.

2007-01-01

Indium tin oxide (ITO) films were deposited by reactive High Target Utilisation Sputtering (HiTUS) onto glass and polyimide substrates. The ion plasma was generated by an RF power source while the target bias voltage was varied from 300 V to 500 V using a separate DC power supply. The deposition rate, at constant target power, increased with DC target voltage due to increased ion energy reaching 34 nm/min at 500 V. All the films were polycrystalline and showed strong (400) and (222) reflections with the relative strength of latter increasing with target bias voltage. The resistivity was lowest at 500 V with values of 1.8 x 10 -4 Ω cm and 2.4 x 10 -4 Ω cm on glass and polyimide, respectively but was still less than 5 x 10 -4 Ω cm at 400 V. All films were highly transparent to visible light, (> 80%) but the NIR transmittance decreased with increasing target voltage due to higher free carrier absorption. Therefore, ITO films can be deposited onto semiconductor layers such as in solar cells, with minimal ion damage while maintaining low resistivity

76 FR 17657 - Medical Device Epidemiology Network 2011: Second Annual Public Workshop

Science.gov (United States)

2011-03-30

... priorities for MDEpiNet. II. Who is the target audience for this public workshop? Who should attend this public workshop? This workshop is open to all interested parties. The target audience is comprised of...

8th International Workshop on Parallel Tools for High Performance Computing

CERN Document Server

Gracia, José; Knüpfer, Andreas; Resch, Michael; Nagel, Wolfgang

2015-01-01

Numerical simulation and modelling using High Performance Computing has evolved into an established technique in academic and industrial research. At the same time, the High Performance Computing infrastructure is becoming ever more complex. For instance, most of the current top systems around the world use thousands of nodes in which classical CPUs are combined with accelerator cards in order to enhance their compute power and energy efficiency. This complexity can only be mastered with adequate development and optimization tools. Key topics addressed by these tools include parallelization on heterogeneous systems, performance optimization for CPUs and accelerators, debugging of increasingly complex scientific applications, and optimization of energy usage in the spirit of green IT. This book represents the proceedings of the 8th International Parallel Tools Workshop, held October 1-2, 2014 in Stuttgart, Germany – which is a forum to discuss the latest advancements in the parallel tools.

Workshop 'Reducing the share of drilling in the total cost of geothermal power generation'; Workshop 'Senkung des bohrtechnischen Anteils an den geothermischen Stromgestehungskosten'

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-07-01

For a further development of geothermal power generation, technological adaptations of drilling technology will be required that will reduce the specific power generation cost. This workshop discussed the options for adaptation and the resulting cost improvements. Both technical and non-technical issues were tackled. The full-text documents of the workshop (overheads) can be downloaded at http://www.ie-leipzig.de. Subjects were: (1) Downhole engine technology; (2) New drilling equipment in consideration of geothermal requirements; (3) New drilling equipment in consideration of geothermal requirements; (4) Innovative drilling concepts/ Current cost allotment; (5) Higher efficiency in drilling with flushing adapted to drilling horizons; (6) MWD/LWD technologies of the KW industry; (7) Completion technology in geothermal plants; (8) Time and cost planning in drilling plans; (9) Cost-optimized drilling from a drilling contractor's view; (10) Requirements and obstacles in the licensing of new drilling equipment. (orig.)

2017 Bipolar Plate Workshop Summary Report

Energy Technology Data Exchange (ETDEWEB)

Kopasz, John P. [Argonne National Lab. (ANL), Argonne, IL (United States); Benjamin, Thomas G. [Argonne National Lab. (ANL), Argonne, IL (United States); Schenck, Deanna [Argonne National Lab. (ANL), Argonne, IL (United States)

2017-08-17

The Bipolar Plate (BP) Workshop was held at USCAR1 in Southfield, Michigan on February 14, 2017 and included 63 participants from industry, government agencies, universities, and national laboratories with expertise in the relevant fields. The objective of the workshop was to identify research and development (R&D) needs, in particular early-stage R&D, for bipolar plates for polymer electrolyte membrane (PEM) fuel cells for transportation applications. The focus of the workshop was on materials, manufacturing, and design aspects of bipolar plates with the goal of meeting DOE’s 2020 bipolar plate targets. Of special interest was the cost target of ≤$3/kW for the bipolar plate.

Hydrogen Technology Education Workshop Proceedings

Energy Technology Data Exchange (ETDEWEB)

None

2002-12-01

This document outlines activities for educating key target audiences, as suggested by workshop participants. Held December 4-5, 2002, the Hydrogen Technology Education Workshop kicked off a new education effort coordinated by the Hydrogen, Fuel Cells, & Infrastructure Technologies Program of the Office of Energy Efficiency and Renewable Energy.

The World in Slow Motion: Using a High-Speed Camera in a Physics Workshop

Science.gov (United States)

Dewanto, Andreas; Lim, Geok Quee; Kuang, Jianhong; Zhang, Jinfeng; Yeo, Ye

2012-01-01

We present a physics workshop for college students to investigate various physical phenomena using high-speed cameras. The technical specifications required, the step-by-step instructions, as well as the practical limitations of the workshop, are discussed. This workshop is also intended to be a novel way to promote physics to Generation-Y…

High-power VCSELs for smart munitions

Science.gov (United States)

Geske, Jon; MacDougal, Michael; Cole, Garrett; Snyder, Donald

2006-08-01

The next generation of low-cost smart munitions will be capable of autonomously detecting and identifying targets aided partly by the ability to image targets with compact and robust scanning rangefinder and LADAR capabilities. These imaging systems will utilize arrays of high performance, low-cost semiconductor diode lasers capable of achieving high peak powers in pulses ranging from 5 to 25 nanoseconds in duration. Aerius Photonics is developing high-power Vertical-Cavity Surface-Emitting Lasers (VCSELs) to meet the needs of these smart munitions applications. The authors will report the results of Aerius' development program in which peak pulsed powers exceeding 60 Watts were demonstrated from single VCSEL emitters. These compact packaged emitters achieved pulse energies in excess of 1.5 micro-joules with multi kilo-hertz pulse repetition frequencies. The progress of the ongoing effort toward extending this performance to arrays of VCSEL emitters and toward further improving laser slope efficiency will be reported.

Workshop on Subcritical Neutron Production

International Nuclear Information System (INIS)

Walter Sadowski; Roald Sagdeev

2006-01-01

Executive Summary of the Workshop on Subcritical Neutron Production A workshop on Subcritical Neutron Production was sponsored by the East-West Center of the University of Maryland on October 11-13, 2004. The subject of the workshop was the application of subcritical neutrons to transmutation of actinides. The workshop was attended by members of the fission, accelerator and fusion communities. Papers on the state of development of neutron production by accelerators, fusion devices, and fission reactors were presented. Discussions were held on the potential of these technologies to solve the problems of spent nuclear waste storage and nuclear non-proliferation presented by current and future nuclear power reactors. A list of participants including their affiliation and their E-Mail addresses is attached. The workshop concluded that the technologies, presently available or under development, hold out the exciting possibility of improving the environmental quality and long term energy resources of nuclear power while strengthening proliferation resistance. The workshop participants agreed on the following statements. The workshop considered a number of technologies to deal with spent nuclear fuels and current actinide inventories. The conclusion was reached that substantial increase in nuclear power production will require that the issue of spent nuclear fuel be resolved. The Workshop concluded that 14 MeV fusion neutrons can be used to destroy nuclear reactor by-products, some of which would otherwise have to be stored for geologic periods of time. The production of 14 MeV neutrons is based on existing fusion technologies at different research institutions in several countries around the world. At the present time this technology is used to produce 14 MeV neutrons in JET. More development work will be required, however, to bring fusion technology to the level where it can be used for actinide burning on an industrial scale. The workshop concluded that the potential

Spallation Neutron Source Second Target Station Integrated Systems Update

Energy Technology Data Exchange (ETDEWEB)

Ankner, John Francis [ORNL; An, Ke [ORNL; Blokland, Willem [ORNL; Charlton, Timothy R. [ORNL; Coates, Leighton [ORNL; Dayton, Michael J. [ORNL; Dean, Robert A. [ORNL; Dominguez-Ontiveros, Elvis E. [ORNL; Ehlers, Georg [ORNL; Gallmeier, Franz X. [ORNL; Graves, Van B. [ORNL; Heller, William T. [ORNL; Holmes, Jeffrey A. [ORNL; Huq, Ashfia [ORNL; Lumsden, Mark D. [ORNL; McHargue, William M. [ORNL; McManamy, Thomas J. [ORNL; Plum, Michael A. [ORNL; Rajic, Slobodan [ORNL; Remec, Igor [ORNL; Robertson, Lee [ORNL; Sala, Gabriele [ORNL; Stoica, Alexandru Dan [ORNL; Trotter, Steven M. [ORNL; Winn, Barry L. [ORNL; Abudureyimu, Reheman [ORNL; Rennich, Mark J. [ORNL; Herwig, Kenneth W. [ORNL

2017-04-01

The Spallation Neutron Source (SNS) was designed from the beginning to accommodate both an accelerator upgrade to increase the proton power and a second target station (STS). Four workshops were organized in 2013 and 2014 to identify key science areas and challenges where neutrons will play a vital role [1-4]. Participants concluded that the addition of STS to the existing ORNL neutron sources was needed to complement the strengths of High Flux Isotope Reactor (HFIR) and the SNS first target station (FTS). To address the capability gaps identified in the workshops, a study was undertaken to identify instrument concepts that could provide the required new science capabilities. The study outlined 22 instrument concepts and presented an initial science case for STS [5]. These instrument concepts formed the basis of a planning suite of instruments whose requirements determined an initial site layout and moderator selection. An STS Technical Design Report (TDR) documented the STS concept based on those choices [6]. Since issue of the TDR, the STS concept has significantly matured as described in this document.

High-foot Implosion Workshop (March 22-24, 2016) Report

Energy Technology Data Exchange (ETDEWEB)

Hurricane, O. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2016-05-06

From March 22-24, 2016 at Workshop was held at Lawrence Livermore National Laboratory bringing together international experts in inertial confinement fusion research for the purpose of discussing the results from the ‘high-foot implosion campaign.’ The Workshop topics covered a retrospective of the first two years of experiments, a discussion of our best present understanding of what the data and our models imply, a discussion about remaining mysteries that are not understood at this time, and a discussion of our strategy moving forward. The material herein contains information from published and unpublished sources and is distributed solely for the purposes of this Workshop. Key assessments and conclusions resulting from the Workshop are: “The high foot campaign is extremely well documented and the interested reader is urged to go directly to the peer-reviewed journal literature for details.” – D. Haynes (LANL) “Overall progress in understanding of fuel and hot-spot properties near peak burn is excellent.” – V. Goncharov (LLE) “I would say that given the constraints of using the same hohlraum and similar capsule designs to the National Ignition Campaign, the High Foot Campaign achieved as much as could be expected. Indeed the demonstration of significant alpha particle heating remains a landmark achievement.” – J. Chittenden (Imperial College) “One of the principal points of discussion at the meeting was the importance of the roll over in inferred pressure that occurs with reducing coast time for different ablator thicknesses and the idea of repeating shot N140819 to confirm this. I would be very interested to see a return to the High Foot platform as a way to exercise the improved radiographic capabilities such as the curved crystal imaging system and as a way to examine the hypothesis of ‘burn truncation by aneurism.’ ” – J. Chittenden (Imperial College) “It is clear from the quality of the data presented during this workshop

US-Japan workshop on field-reversed configurations with steady-state high-temperature fusion plasmas and the 11th US-Japan workshop on compact toroids

International Nuclear Information System (INIS)

Barnes, D.C.; Fernandez, J.C.; Rej, D.J.

1990-05-01

The US-Japan Workshop on Field-Reversed Configurations with Steady-State High-Temperature Fusion Plasma and the 11th US-Japan Workshop on Compact Toroids were held at Los Alamos National Laboratory, Los Alamos, New Mexico on November 7--9, 1989. These proceedings contain the papers presented at the workshops as submitted by the authors. These papers have been indexed separately

US-Japan workshop on field-reversed configurations with steady-state high-temperature fusion plasmas and the 11th US-Japan workshop on compact toroids

Energy Technology Data Exchange (ETDEWEB)

Barnes, D.C.; Fernandez, J.C.; Rej, D.J. (comps.)

1990-05-01

The US-Japan Workshop on Field-Reversed Configurations with Steady-State High-Temperature Fusion Plasma and the 11th US-Japan Workshop on Compact Toroids were held at Los Alamos National Laboratory, Los Alamos, New Mexico on November 7--9, 1989. These proceedings contain the papers presented at the workshops as submitted by the authors. These papers have been indexed separately.

High pressure and synchrotron radiation satellite workshop

Energy Technology Data Exchange (ETDEWEB)

Bass, J.; Guignot, N.; Morard, G.; Mezouar, M.; Andrault, D.; Bolfan-Casanova, N.; Sturhahn, W.; Daniel, I.; Reynard, B.; Simionovici, A.; Sanchez Valle, C.; Martinez, I.; Kantor, I.; Dubrovinsky, I.; Mccammon, C.; Dubrovinskaia, N.; Kurnosiv, A.; Kuznetsov, A.; Goncharenko, I.; Loubeyre, P.; Desgreniers, S.; Weck, G.; Yoo, C.S.; Iota, V.; Park, J.; Cynn, H.; Gorelli, F.; Toulemonde, P.; Machon, D.; Merlen, A.; San Miguel, A.; Amboage, M.; Aquilanti, G.; Mathon, O.; Pascarelli, S.; Itie, J.P.; Mcmillan, P.F.; Trapananti, A.; Di Cicco, A.; Panfilis, S. de; Filipponi, A.; Kreisel, J.; Bouvier, P.; Dkhil, B.; Chaabane, B.; Rosner, H.; Koudela, D.; Schwarz, U.; Handestein, A.; Hanfland, M.; Opahle, I.; Koepernik, K.; Kuzmin, M.; Mueller, K.H.; Mydosh, J.; Richter, M.; Hejny, C.; Falconi, S.; Lundegaard, L.F.; Mcmahon, M.I; Loa, I.; Syassen, K.; Wang, X.; Roth, H.; Lorenz, T.; Farber Daniel, I.; Antonangeli Daniele, I.; Krisch, M.; Badro, J.; Fiquet, G.; Occelli, F.; Mao, W.L.; Mao, H.K.; Eng, P.; Kao, C.C.; Shu, J.F.; Hemley, R.J.; Tse, J.S.; Yao, Y.; Deen, P.P.; Paolasini, I.; Braithwaite, D.; Kernavanois, N.; Lapertot, G.; Rupprecht, K.; Leupold, O.; Ponkratz, U.; Wortmann, G.; Beraud, A.; Krisch, M.; Farber, D.; Antonangeli, D.; Aracne, C.; Zarestky, J.L.; Mcqueeney, R.; Mathon, O.; Baudelet, F.; Decremps, F.; Itie, J.P.; Nataf, I.; Pascarelli, S.; Polian, A

2006-07-01

The workshop is dedicated to recent advances on science at high pressure at third generation synchrotron sources. A variety of experiments using synchrotron radiation techniques including X-ray diffraction, EXAFS (extended X-ray absorption fine structure), inelastic X-ray scattering, Compton scattering and Moessbauer spectroscopy of crystalline, liquid or amorphous samples, are reported. This document gathers the abstracts of the presentations.

High pressure and synchrotron radiation satellite workshop

International Nuclear Information System (INIS)

Bass, J.; Guignot, N.; Morard, G.; Mezouar, M.; Andrault, D.; Bolfan-Casanova, N.; Sturhahn, W.; Daniel, I.; Reynard, B.; Simionovici, A.; Sanchez Valle, C.; Martinez, I.; Kantor, I.; Dubrovinsky, I.; Mccammon, C.; Dubrovinskaia, N.; Kurnosiv, A.; Kuznetsov, A.; Goncharenko, I.; Loubeyre, P.; Desgreniers, S.; Weck, G.; Yoo, C.S.; Iota, V.; Park, J.; Cynn, H.; Gorelli, F.; Toulemonde, P.; Machon, D.; Merlen, A.; San Miguel, A.; Amboage, M.; Aquilanti, G.; Mathon, O.; Pascarelli, S.; Itie, J.P.; Mcmillan, P.F.; Trapananti, A.; Di Cicco, A.; Panfilis, S. de; Filipponi, A.; Kreisel, J.; Bouvier, P.; Dkhil, B.; Chaabane, B.; Rosner, H.; Koudela, D.; Schwarz, U.; Handestein, A.; Hanfland, M.; Opahle, I.; Koepernik, K.; Kuzmin, M.; Mueller, K.H.; Mydosh, J.; Richter, M.; Hejny, C.; Falconi, S.; Lundegaard, L.F.; Mcmahon, M.I; Loa, I.; Syassen, K.; Wang, X.; Roth, H.; Lorenz, T.; Farber Daniel, I.; Antonangeli Daniele, I.; Krisch, M.; Badro, J.; Fiquet, G.; Occelli, F.; Mao, W.L.; Mao, H.K.; Eng, P.; Kao, C.C.; Shu, J.F.; Hemley, R.J.; Tse, J.S.; Yao, Y.; Deen, P.P.; Paolasini, I.; Braithwaite, D.; Kernavanois, N.; Lapertot, G.; Rupprecht, K.; Leupold, O.; Ponkratz, U.; Wortmann, G.; Beraud, A.; Krisch, M.; Farber, D.; Antonangeli, D.; Aracne, C.; Zarestky, J.L.; Mcqueeney, R.; Mathon, O.; Baudelet, F.; Decremps, F.; Itie, J.P.; Nataf, I.; Pascarelli, S.; Polian, A.

2006-01-01

The workshop is dedicated to recent advances on science at high pressure at third generation synchrotron sources. A variety of experiments using synchrotron radiation techniques including X-ray diffraction, EXAFS (extended X-ray absorption fine structure), inelastic X-ray scattering, Compton scattering and Moessbauer spectroscopy of crystalline, liquid or amorphous samples, are reported. This document gathers the abstracts of the presentations

Report of the workshop on rf heating in mirror systems

International Nuclear Information System (INIS)

Price, R.E.; Woo, J.T.

1980-08-01

This report is prepared from the proceedings of the Workshop on RF Heating in Magnetic Mirror Systems held at DOE Headquarters in Washington, DC, on March 10-12, 1980. The workshop was organized into four consecutive half-day sessions of prepared talks and one half-day discussion. The first session on tandem mirror concepts and program plans served to identify the opportunities for the application of rf power and the specific approaches that are being pursued. A summary of the ideas presented in this session is given. The following sessions of the workshop were devoted to an exposition of current theoretical and experimental knowledge on the interaction of rf power with magnetically confined, dense, high temperature plasmas at frequencies near the electron cyclotron resonance, lower hybrid resonance and ion cyclotron resonance (including magnetosonic) ranges. The conclusions from these proceedings are presented

Workshop on high heat load x-ray optics

Energy Technology Data Exchange (ETDEWEB)

1990-01-01

A workshop on High Heat Load X-Ray Optics'' was held at Argonne National Laboratory on August 3--5, 1989. The object of this workshop was to discuss recent advances in the art of cooling x-ray optics subject to high heat loads from synchrotron beams. The cooling of the first optical element in the intense photon beams that will be produced in the next generation of synchrotron sources is recognized as one of the major challenges that must be faced before one will be able to use these very intense beams in future synchrotron experiments. Considerable advances have been made in this art during the last few years, but much work remains to be done before the heating problem can be said to be completely solved. Special emphasis was placed on recent cooling experiments and detailed finite element'' and finite difference'' calculations comparing experiment with theory and extending theory to optimize performance.

Workshop on high heat load x-ray optics

International Nuclear Information System (INIS)

1990-01-01

A workshop on ''High Heat Load X-Ray Optics'' was held at Argonne National Laboratory on August 3--5, 1989. The object of this workshop was to discuss recent advances in the art of cooling x-ray optics subject to high heat loads from synchrotron beams. The cooling of the first optical element in the intense photon beams that will be produced in the next generation of synchrotron sources is recognized as one of the major challenges that must be faced before one will be able to use these very intense beams in future synchrotron experiments. Considerable advances have been made in this art during the last few years, but much work remains to be done before the heating problem can be said to be completely solved. Special emphasis was placed on recent cooling experiments and detailed ''finite element'' and ''finite difference'' calculations comparing experiment with theory and extending theory to optimize performance

Providing a computing environment for a high energy physics workshop

International Nuclear Information System (INIS)

Nicholls, J.

1991-03-01

Although computing facilities have been provided at conferences and workshops remote from the hose institution for some years, the equipment provided has rarely been capable of providing for much more than simple editing and electronic mail over leased lines. This presentation describes the pioneering effort involved by the Computing Department/Division at Fermilab in providing a local computing facility with world-wide networking capability for the Physics at Fermilab in the 1990's workshop held in Breckenridge, Colorado, in August 1989, as well as the enhanced facilities provided for the 1990 Summer Study on High Energy Physics at Snowmass, Colorado, in June/July 1990. Issues discussed include type and sizing of the facilities, advance preparations, shipping, on-site support, as well as an evaluation of the value of the facility to the workshop participants

6th International Microbeam Workshop

Energy Technology Data Exchange (ETDEWEB)

Dr Kevin M. Prise

2004-01-01

The extended abstracts which are submitted here present a summary of the proceedings of the 6th International Workshop/12th LH Gray Workshop: Microbeam Probes of Cellular Radiation Response, held at St. Catherine's College, University of Oxford, UK on March, 29th-31st, 2003. In 1993 the 4th LH Gray Workshop entitled ''Microbeam Probes of Cellular Radiation Response'' was held at the Gray Cancer Institute in Northwood. This was organized by Prof BD Michael, Dr M. Folkard and Dr KM Prise and brought together 40 participants interested in developing and applying new microbeam technology to problems in radiation biology (1). The workshop was an undoubted success and has spawned a series of subsequent workshops every two years. In the past, these workshops have been highly successful in bringing together groups interested in developing and applying micro-irradiation techniques to the study of cell and tissue damage by ionizing radiations. Following the first microbeam workshop, there has been a rapid growth in the number of centres developing radiobiology microbeams, or planning to do so and there are currently 15-20 worldwide. Much of the recent research using microbeams has used them to study low-dose effects and ''non-targeted'' responses such bystander effects, genomic instability and adaptive responses. The goal of the 6th workshop was to build on our knowledge of the development of microbeam approaches and the application to radiation biology in the future with the meeting stretching over a 3 day period. Over 80 participants reviewed the current state of radiobiology microbeam research worldwide and reported on new technological developments both in the fields of physics and biology.

Workshop on scientific applications of coherent x-rays

Energy Technology Data Exchange (ETDEWEB)

Arthur, J.; Materlik, G.; Winick, H. [Stanford Univ., CA (United States). Stanford Linear Accelerator Center]|[Stanford Univ., CA (United States). Stanford Synchrotron Radiation Lab.; Birgeneau, R.J. [Massachusetts Institute of Technology, Cambridge, MA (United States); Fadley, C.S. [Lawrence Berkeley Lab., CA (United States). Materials Science Division

1994-02-12

This is a report on a workshop held at SLAC on February 12, 1994 to assess the science that would become possible using high peak power, short pulses of coherent radiation from a Free Electron Laser (FEL) operating in the hard x-ray region, at wavelengths down to about 1 {angstrom}. Sixty-three people participated in the workshop. The appendices to this report give a list of participants, the workshop agenda, and the charge to the workshop. Material describing the performance parameters of several possible sources was made available to the participants along with a graph showing the spectral distribution of the spontaneous as well as the coherent radiation and a note on peak power issues. This material is also included as an appendix to this report. This report consists of an Executive Summary, brief summaries by the speaker for each of the talks that were given, and copies of some of the viewgraphs that were shown. Also included are important points raised in the discussions that followed each talk. In addition, two contributions from scientists who could not attend the workshop are included, plus one contribution received from a participant after the workshop. A serious storm on the East coast made it impossible for three speakers and several intended participants to reach Stanford. The talk by Janos Kirz was presented by Malcolm Howells using viewgraphs sent by FAX. The talks by Keith Nelson and Brian Stephenson were not given. We include summaries by them of the talks they would have given, plus copies of some of their viewgraphs, in this report.

Workshop on scientific applications of coherent x-rays

International Nuclear Information System (INIS)

Arthur, J.; Materlik, G.; Winick, H.; Fadley, C.S.

1994-01-01

This is a report on a workshop held at SLAC on February 12, 1994 to assess the science that would become possible using high peak power, short pulses of coherent radiation from a Free Electron Laser (FEL) operating in the hard x-ray region, at wavelengths down to about 1 angstrom. Sixty-three people participated in the workshop. The appendices to this report give a list of participants, the workshop agenda, and the charge to the workshop. Material describing the performance parameters of several possible sources was made available to the participants along with a graph showing the spectral distribution of the spontaneous as well as the coherent radiation and a note on peak power issues. This material is also included as an appendix to this report. This report consists of an Executive Summary, brief summaries by the speaker for each of the talks that were given, and copies of some of the viewgraphs that were shown. Also included are important points raised in the discussions that followed each talk. In addition, two contributions from scientists who could not attend the workshop are included, plus one contribution received from a participant after the workshop. A serious storm on the East coast made it impossible for three speakers and several intended participants to reach Stanford. The talk by Janos Kirz was presented by Malcolm Howells using viewgraphs sent by FAX. The talks by Keith Nelson and Brian Stephenson were not given. We include summaries by them of the talks they would have given, plus copies of some of their viewgraphs, in this report

Workshop on processing of nuclear data for use in power reactor pressure vessel lifetime assessment. Summary report

International Nuclear Information System (INIS)

Paviotti Corcuera, R.; Greenwood, L.R.; Muir, D.W.

1999-02-01

This document summarizes the contents of the workshop on processing of nuclear data for use in power reactor pressure vessel lifetime assessment. A short description of the main topics of the agenda, the list of participants and comments and recommendations are given. (author)

Integrated Targeting and Guidance for Powered Planetary Descent

Science.gov (United States)

Azimov, Dilmurat M.; Bishop, Robert H.

2018-02-01

This paper presents an on-board guidance and targeting design that enables explicit state and thrust vector control and on-board targeting for planetary descent and landing. These capabilities are developed utilizing a new closed-form solution for the constant thrust arc of the braking phase of the powered descent trajectory. The key elements of proven targeting and guidance architectures, including braking and approach phase quartics, are employed. It is demonstrated that implementation of the proposed solution avoids numerical simulation iterations, thereby facilitating on-board execution of targeting procedures during the descent. It is shown that the shape of the braking phase constant thrust arc is highly dependent on initial mass and propulsion system parameters. The analytic solution process is explicit in terms of targeting and guidance parameters, while remaining generic with respect to planetary body and descent trajectory design. These features increase the feasibility of extending the proposed integrated targeting and guidance design to future cargo and robotic landing missions.

4th International Workshop on Adaptive Optics for Industry and Medicine

CERN Document Server

Wittrock, Ulrich

2005-01-01

This book treats the development and application of adaptive optics for industry and medicine. The contributions describe recently developed components for adaptive-optics systems such as deformable mirrors, wavefront sensors, and mirror drivers as well as complete adaptive optical systems and their applications in industry and medicine. Applications range from laser-beam forming and adaptive aberration correction for high-power lasers to retinal imaging in ophthalmology. The contributions are based on presentations made at the 4th International Workshop on Adaptive Optics in Industry and Medicine which took place in Münster, Germany, in October 2003. This highly successful series of workshops on adaptive optics started in 1997 and continues with the 5th workshop in Beijing in 2005.

Calculations of high-power production target and beamdump for the GSI future Super-FRS for a fast extraction scheme at the FAIR Facility

International Nuclear Information System (INIS)

Tahir, N A; Weick, H; Iwase, H

2005-01-01

A superconducting fragment separator (Super-FRS) is being designed for the production and separation of radioactive isotopes at the future FAIR (Facility for Antiprotons and Ion Research) facility at Darmstadt. This paper discusses various aspects and requirements for the high-power production target that will be used in the Super-FRS experiments. The production target must survive over an extended period of time as it will be used during the course of many experiments. The specific power deposited by the high intensity beam that will be generated at the future FAIR facility will be high enough to destroy the target in most of the cases as a result of a single shot from the new heavy ion synchrotrons SIS100/300. By using an appropriate beam intensity and focal spot parameters, the target would survive after being irradiated once. However, the heat should be dissipated efficiently before the same target area is irradiated again. We have considered a wheel shaped solid carbon target that rotates around its axis so that different areas of the target are irradiated successively. This allows for cooling of the beam heated region by thermal conduction before the same part of the target is irradiated a second time. Another attractive option is to use a liquid jet target at the Super-FRS. First calculations of a possible liquid lithium target are also presented in this paper. One of the advantages of using lithium as a target is that it will survive even if one uses a smaller focal spot, which has half the area of that used for a solid carbon target. This will significantly improve the isotope resolution. A similar problem associated with these experiments will be safe deposition of the beam energy in a beamdump after its interaction with the production target. We also present calculations to study the suitability of a proposed beamdump

Proceedings of a high temperature superconductivity strategy workshop

International Nuclear Information System (INIS)

Kurzfeld, A.

1987-07-01

The paper contains the proceedings of a high temperature superconductivity strategy workshop, held at the Rutherford Appleton Laboratory, United Kingdom, 1987. The purpose of the meeting was to consider the U.K. strategy to be adopted for the high Tsub(c) superconductors and their application. The notes are presented of five Working Groups examining the following subjects: materials preparation, structural evaluation, physical properties, theoretical studies, and applications. (UK)

Summary Report for Concentrating Solar Power Thermal Storage Workshop: New Concepts and Materials for Thermal Energy Storage and Heat-Transfer Fluids, May 20, 2011

Energy Technology Data Exchange (ETDEWEB)

Glatzmaier, G.

2011-08-01

This document summarizes a workshop on thermal energy storage for concentrating solar power (CSP) that was held in Golden, Colorado, on May 20, 2011. The event was hosted by the U.S. Department of Energy (DOE), the National Renewable Energy Laboratory, and Sandia National Laboratories. The objective was to engage the university and laboratory research communities to identify and define research directions for developing new high-temperature materials and systems that advance thermal energy storage for CSP technologies. This workshop was motivated, in part, by the DOE SunShot Initiative, which sets a very aggressive cost goal for CSP technologies -- a levelized cost of energy of 6 cents per kilowatt-hour by 2020 with no incentives or credits.

FINPIE/97. Workshop proceedings

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

This publication contains the proceedings of 1997 Finnish Workshop on Power and Industrial Electronics, held in Espoo, Finland, on 26 August, 1997. The programme consisted of technical sessions on Advanced AC Motor Control, Electric Machines and Drives, Advanced Control and Measurement, Power Electronics Systems, Modelling and Simulation, and Power Converters

Proceedings of the workshop on 'anomalous electronic states and physical properties in high-temperature superconductors'

International Nuclear Information System (INIS)

Arai, Masatoshi; Kajimoto, Ryoichi

2007-03-01

A workshop entitled 'Anomalous Electronic States and Physical Properties in High-Temperature Superconductors' was held on November 7-8, 2006 at Institute for Materials Research, Tohoku University. In the workshop, leading scientists in the field of high-T c superconductivity, both experimentalists and theorists, gathered in a hall to report the recent progress of the study, clarify the problems to be solved, and discuss the future prospects. The workshop was jointly organized by Specially Promoted Research of MEXT, Development of the 4D Spaces Access Neutron Spectrometer and Elucidation of the Mechanism of Oxide High-T c Superconductivity' (repr. by M. Arai, JAEA) and by the Inter-university Cooperative Research Program of the Institute for Materials Research, Tohoku University, 'Anomalous Electronic States and Physical Properties in High-Temperature Superconductors' (repr. by T. Tohyama, Kyoto Univ.). This report includes abstracts and materials of the presentations in the workshop. (author)

A flexible testing facility for high-power targets T-MIF

International Nuclear Information System (INIS)

Fusco, Y.; Samec, K.; Behzad, M.; Kadi, Y.

2015-01-01

A dedicated material test irradiation facility is being proposed. The testing station will allow critical issues concerning materials under irradiation to be addressed, such as the impact of proton beam irradiation, neutron irradiation, liquid metal corrosion and temperature. The material samples to be investigated in such a facility will be subjected to tensile stress, either constant or cyclical. The facility may also be used for sensor development under irradiation and isotope production. The goal of the current work is to propose a facility that is sufficiently versatile and compact so that it may be transported and used in different laboratories. The power is limited to 100 kW. The general aspect of the proposed irradiation facility is a cube, 2 metres deep and comprising within it all the necessary systems. The interface to the laboratory is limited to the coolant connections, the secondary circuit, the electric energy supply and the signals from the instrumentation. The liquid metal target placed in the centre of the facility contains the samples which are subjected to a proton beam, creating irradiation damage directly through protons or indirectly through neutrons created by spallation of the surrounding liquid metal by the incoming protons. The design of the target is based upon the EURISOL target. The same beam window design is used, albeit stretched horizontally to adopt an elliptical section which is compatible with the shape of the beam used to irradiate the samples. The liquid metal in the target is re-circulated by an electromagnetic pump that drives the liquid metal through a heat exchanger located at the top of the facility, the position of which was chosen to encourage natural circulation. The heat exchanger is made up of two separate parts which allow the primary and secondary circuit to separate cleanly

The proceedings of the KEK FEL simulation code workshop

International Nuclear Information System (INIS)

Kamitani, Takuya

1992-11-01

This is the record of the lectures in free electron laser simulation code workshop held in National Laboratory for High Energy Physics on March 15, 1991. As the device that can generate especially powerful and coherent light in the wide wavelength region from long wavelength like microwave to short wavelength like X-ray and gamma ray, the interest in free electron laser has heightened in Japan and foreign countries, and also the experiments have been carried out actively. Also the necessity of the quantitative theoretical calculation using the simulation has become high, and the researches have been carried out in various places. This workshop was held for the intention of offering the place for the interchange of researches, the exchange of information and discussion. 39 persons took part in the workshop, and 11 lectures were given, and it was very useful. (K.I.)

Sixth international wind-diesel workshop

International Nuclear Information System (INIS)

1992-01-01

At a workshop on hybrid wind/diesel power generation systems, papers were presented on international research programs, demonstration projects, wind/diesel deployment strategies and requirements, wind/diesel market development and economics, wind turbine design requirements, and wind/diesel models and analytical tools. Separate abstracts have been prepared for 11 papers from this workshop

Sixth international wind-diesel workshop

Energy Technology Data Exchange (ETDEWEB)

1992-01-01

At a workshop on hybrid wind/diesel power generation systems, papers were presented on international research programs, demonstration projects, wind/diesel deployment strategies and requirements, wind/diesel market development and economics, wind turbine design requirements, and wind/diesel models and analytical tools. Separate abstracts have been prepared for 11 papers from this workshop.

The second workshop of neutron science research program

Energy Technology Data Exchange (ETDEWEB)

Yasuda, Hideshi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Tone, Tatsuzo [eds.

1997-11-01

The Japan Atomic Energy Research Institute(JAERI) has been proposing the Neutron Science Research Program to explore a broad range of basic research and the nuclear technology including actinide transmutation with use of powerful spallation neutron sources. For this purpose, the JAERI is conducting the research and development of an intense proton linac, the development of targets, as well as the conceptual design study of experimental facilities required for applications of spallation neutrons and secondary particle beams. The Special Task Force for Neutron Science Initiative was established in May 1996 to promote aggressively and systematically the Neutron Science Research Program. The second workshop on neutron science research program was held at the JAERI Tokai Research Establishment on 13 and 14 March 1997 for the purpose of discussing the results obtained since the first workshop in March 1996. The 27 of the presented papers are indexed individually. (J.P.N.)

Review of the SLAC and Les Houches workshops

International Nuclear Information System (INIS)

Prescott, C.Y.

1994-12-01

Polarized Electron Source workshops have been held at varying intervals, beginning in 1983 when Charles Sinclair convened the first at SLAC. Since that time, three workshops were held in conjunction with the International Spin Symposia and two at other occasions. The increasing importance of polarized electron beams at accelerators has stimulated interest in these workshops. Two workshops have been held since the last International Spin Symposium in Nagoya. In 1993, a workshop was held at SLAC, and in 1994 at Les Houches, a polarized electron beam session was held as part of a polarized beam and targets workshop. This report summarizes highlights from the latter two workshops

Workshop on Accelerators for Heavy Ion Fusion: Summary Report of the Workshop

Energy Technology Data Exchange (ETDEWEB)

Seidl, P.A.; Barnard, J.J.

2011-04-29

The Workshop on Accelerators for Heavy Ion Fusion was held at Lawrence Berkeley National Laboratory May 23-26, 2011. The workshop began with plenary sessions to review the state of the art in HIF (heavy ion fusion), followed by parallel working groups, and concluded with a plenary session to review the results. There were five working groups: IFE (inertial fusion energy) targets, RF approach to HIF, induction accelerator approach to HIF, chamber and driver interface, ion sources and injectors.

High power accelerator-based boron neutron capture with a liquid lithium target and new applications to treatment of infectious diseases

Energy Technology Data Exchange (ETDEWEB)

Halfon, S. [Soreq NRC, Yavne 81800 (Israel); Racah Institute of Physics, Hebrew University, Jerusalem 91904 (Israel)], E-mail: halfon@phys.huji.ac.il; Paul, M. [Racah Institute of Physics, Hebrew University, Jerusalem 91904 (Israel); Steinberg, D. [Biofilm Laboratory, Institute of Dental Sciences, Faculty of Dentistry, Hebrew University-Hadassah (Israel); Nagler, A.; Arenshtam, A.; Kijel, D. [Soreq NRC, Yavne 81800 (Israel); Polacheck, I. [Clinical Microbiology and Infectious Diseases, Hadassah-Hebrew University Medical Center (Israel); Srebnik, M. [Department of Medicinal Chemistry and Natural Products, School of Pharmacy, Hebrew University, Jerusalem 91120 (Israel)

2009-07-15

A new conceptual design for an accelerator-based boron neutron capture therapy (ABNCT) facility based on the high-current low-energy proton beam driven by the linear accelerator at SARAF (Soreq Applied Research Accelerator Facility) incident on a windowless forced-flow liquid-lithium target, is described. The liquid-lithium target, currently in construction at Soreq NRC, will produce a neutron field suitable for the BNCT treatment of deep-seated tumor tissues, through the reaction {sup 7}Li(p,n){sup 7}Be. The liquid-lithium target is designed to overcome the major problem of solid lithium targets, namely to sustain and dissipate the power deposited by the high-intensity proton beam. Together with diseases conventionally targeted by BNCT, we propose to study the application of our setup to a novel approach in treatment of diseases associated with bacterial infections and biofilms, e.g. inflammations on implants and prosthetic devices, cystic fibrosis, infectious kidney stones. Feasibility experiments evaluating the boron neutron capture effectiveness on bacteria annihilation are taking place at the Soreq nuclear reactor.

The Science and Issues of Human DNA Polymoprhisms: A Training Workshop for High School Biology Teachers

Energy Technology Data Exchange (ETDEWEB)

David. A Micklos

2006-10-30

kits by Carolina Biological rose from 700 units in 1999 to 1,132 in 2000 – a 62% increase. Competing kits using the Alu system, and based substantially on our earlier work, are also marketed by Biorad and Edvotek. In parallel with the lab experiments, we developed a suite of database/statistical applications and easy-to-use interfaces that allow students to use their own DNA data to explore human population genetics and to test theories of human evolution. Database searches and statistical analyses are launched from a centralized workspace. Workshop participants were introduced to these and other resources available at the DNALC WWW site (http://vector.cshl.org/bioserver/): 1) Allele Server tests Hardy-Weinberg equilibrium and statistically compares PV92 data from world populations. 2) Sequence Server uses DNA sequence data to search Genbank using BLASTN, compare sequences using CLUSTALW, and create phylogenetic trees using PHYLIP. 3) Simulation Server uses a Monte Carlo generator to model the long-term effects of drift, selection, and population bottlenecks. By targeting motivated and innovative biology faculty, we believe that this project offered a cost-effective means to bring high school biology education up-to-the-minute with genomic biology. The workshop reached a target audience of highly professional faculty who have already implemented hands-on labs in molecular genetics and many of whom offer laboratory electives in biotechnology. Many attend professional meetings, develop curriculum, collaborate with scientists, teach faculty workshops, and manage equipment-sharing programs. These individuals are life-long learners, anxious for deeper insight and additional training to further extend their leadership. This contention was supported by data from a mail survey, conducted in February-March 2000 and 2001, of 256 faculty who participated in workshops conducted during the current term of DOE support. Seventy percent of participants responded, providing direct

The Science and Issues of Human DNA Polymorphisms: A Training Workshop for High School Biology Teachers

Energy Technology Data Exchange (ETDEWEB)

Micklos, David A.

2006-10-30

polymorphism kits by Carolina Biological rose from 700 units in 1999 to 1,132 in 2000 â a 62% increase. Competing kits using the Alu system, and based substantially on our earlier work, are also marketed by Biorad and Edvotek. In parallel with the lab experiments, we developed a suite of database/statistical applications and easy-to-use interfaces that allow students to use their own DNA data to explore human population genetics and to test theories of human evolution. Database searches and statistical analyses are launched from a centralized workspace. Workshop participants were introduced to these and other resources available at the DNALC WWW site (http://vector.cshl.org/bioserver/): 1) Allele Server tests Hardy-Weinberg equilibrium and statistically compares PV92 data from world populations. 2) Sequence Server uses DNA sequence data to search Genbank using BLASTN, compare sequences using CLUSTALW, and create phylogenetic trees using PHYLIP. 3) Simulation Server uses a Monte Carlo generator to model the long-term effects of drift, selection, and population bottlenecks. By targeting motivated and innovative biology faculty, we believe that this project offered a cost-effective means to bring high school biology education up-to-the-minute with genomic biology. The workshop reached a target audience of highly professional faculty who have already implemented hands-on labs in molecular genetics and many of whom offer laboratory electives in biotechnology. Many attend professional meetings, develop curriculum, collaborate with scientists, teach faculty workshops, and manage equipment-sharing programs. These individuals are life-long learners, anxious for deeper insight and additional training to further extend their leadership. This contention was supported by data from a mail survey, conducted in February-March 2000 and 2001, of 256 faculty who participated in workshops conducted during the current term of DOE support. Seventy percent of participants responded, providing

9{sup th} international workshop on large-scale integration of wind power into power systems as well as on transmission networks for offshore wind power plants. Proceedings

Energy Technology Data Exchange (ETDEWEB)

Betancourt, Uta; Ackermann, Thomas (eds.)

2010-07-01

Within the 9th International Workshop on large-scale integration of wind power into power systems as well as on transmission networks for offshore wind power plants at 18th to 19th October, 2010 in Quebec (Canada), lectures and poster papers were presented to the following themes: (1) Keynote session and panel; (2) European grid integration studies; (3) Modeling; (4) Wind forecasting; (5) North American grid integration studies; (6) Voltage stability and control; (7) Grid codes and impact studies; (8) Canadian University research (WESNet); (9) Operation and dispatch; (9) Offshore wind power plants; (10) Frequency Control; (11) Methodologies to estimate wind power impacts on power systems, summaries from IEAWIND collaboration; (12) HVDC; (13) Grid codes and system impact studies; (14) Modeling and validation; (15) Regulations, markets and offshore wind energy; (16) Integration issues; (17) Wind turbine control system; (18) Energy management and IT solutions.

HTS Wire Development Workshop: Proceedings

Energy Technology Data Exchange (ETDEWEB)

1994-07-01

The 1994 High-Temperature Superconducting Wire Development Workshop was held on February 16--17 at the St. Petersburg Hilton and Towers in St. Petersburg, Florida. The meeting was hosted by Florida Power Corporation and sponsored by the US Department of Energy`s Superconductivity Program for Electric Power Systems. The meeting focused on recent high-temperature superconducting wire development activities in the Department of Energy`s Superconductivity Systems program. The meeting opened with a general discussion on the needs and benefits of superconductivity from a utility perspective, the US global competitiveness position, and an outlook on the overall prospects of wire development. The meeting then focused on four important technology areas: Wire characterization: issues and needs; technology for overcoming barriers: weak links and flux pinning; manufacturing issues for long wire lengths; and physical properties of HTS coils. Following in-depth presentations, working groups were formed in each technology area to discuss the most important current research and development issues. The working groups identified research areas that have the potential for greatly enhancing the wire development effort. These areas are discussed in the summary reports from each of the working groups. This document is a compilation of the workshop proceedings including all general session presentations and summary reports from the working groups.

Using sound to modify fish behavior at power-production and water-control facilities: A workshop. Phase 2: Final report

International Nuclear Information System (INIS)

Carlson, T.J.; Popper, A.N.

1997-06-01

A workshop on ''''Use of Sound for Fish Protection at Power-Production and Water-Control Facilities'''' was held in Portland, Oregon on December 12--13, 1995. This workshop convened a 22-member panel of international experts from universities, industry, and government to share knowledge, questions, and ideas about using sound for fish guidance. Discussions involved in a broad range of indigenous migratory and resident fish species and fish-protection issues in river systems, with particular focus on the Columbia River Basin. Because the use of sound behavioral barriers for fish is very much in its infancy, the workshop was designed to address the many questions being asked by fishery managers and researchers about the feasibility and potential benefits of using sound to augment physical barriers for fish protection in the Columbia River system

Safety targets for nuclear power plants

International Nuclear Information System (INIS)

Herttrich, P.M.

1985-01-01

By taking as an example the safety targets of the American nuclear energy authority US-NRC, this paper explains what is meant by global, quantitative safety targets for nuclear power plants and what expectations are associated with the selecton of such safety targets. It is shown how probabilistic methods can be an appropriate completion of proven deterministic methods and what are the sectors where their application may become important in future. (orig./HP) [de

MO-AB-210-02: Ultrasound Imaging and Therapy-Hands On Workshop

International Nuclear Information System (INIS)

Sammet, S.

2015-01-01

The goal of this ultrasound hands-on workshop is to demonstrate advancements in high intensity focused ultrasound (HIFU) and to demonstrate quality control (QC) testing in diagnostic ultrasound. HIFU is a therapeutic modality that uses ultrasound waves as carriers of energy. HIFU is used to focus a beam of ultrasound energy into a small volume at specific target locations within the body. The focused beam causes localized high temperatures and produces a well-defined regions of necrosis. This completely non-invasive technology has great potential for tumor ablation and targeted drug delivery. At the workshop, attendees will see configurations, applications, and hands-on demonstrations with on-site instructors at separate stations. The involvement of medical physicists in diagnostic ultrasound imaging service is increasing due to QC and accreditation requirements. At the workshop, an array of ultrasound testing phantoms and ultrasound scanners will be provided for attendees to learn diagnostic ultrasound QC in a hands-on environment with live demonstrations of the techniques. Target audience: Medical physicists and other medical professionals in diagnostic imaging and radiation oncology with interest in high-intensity focused ultrasound and in diagnostic ultrasound QC. Learning Objectives: Learn ultrasound physics and safety for HIFU applications through live demonstrations Get an overview of the state-of-the art in HIFU technologies and equipment Gain familiarity with common elements of a quality control program for diagnostic ultrasound imaging Identify QC tools available for testing diagnostic ultrasound systems and learn how to use these tools List of supporting vendors for HIFU and diagnostic ultrasound QC hands-on workshop: Philips Healthcare Alpinion Medical Systems Verasonics, Inc Zonare Medical Systems, Inc Computerized Imaging Reference Systems (CIRS), Inc. GAMMEX, Inc., Cablon Medical BV Steffen Sammet: NIH/NCI grant 5R25CA132822, NIH/NINDS grant 5R25NS

MO-AB-210-01: Ultrasound Imaging and Therapy-Hands On Workshop

International Nuclear Information System (INIS)

Lu, Z.

2015-01-01

The goal of this ultrasound hands-on workshop is to demonstrate advancements in high intensity focused ultrasound (HIFU) and to demonstrate quality control (QC) testing in diagnostic ultrasound. HIFU is a therapeutic modality that uses ultrasound waves as carriers of energy. HIFU is used to focus a beam of ultrasound energy into a small volume at specific target locations within the body. The focused beam causes localized high temperatures and produces a well-defined regions of necrosis. This completely non-invasive technology has great potential for tumor ablation and targeted drug delivery. At the workshop, attendees will see configurations, applications, and hands-on demonstrations with on-site instructors at separate stations. The involvement of medical physicists in diagnostic ultrasound imaging service is increasing due to QC and accreditation requirements. At the workshop, an array of ultrasound testing phantoms and ultrasound scanners will be provided for attendees to learn diagnostic ultrasound QC in a hands-on environment with live demonstrations of the techniques. Target audience: Medical physicists and other medical professionals in diagnostic imaging and radiation oncology with interest in high-intensity focused ultrasound and in diagnostic ultrasound QC. Learning Objectives: Learn ultrasound physics and safety for HIFU applications through live demonstrations Get an overview of the state-of-the art in HIFU technologies and equipment Gain familiarity with common elements of a quality control program for diagnostic ultrasound imaging Identify QC tools available for testing diagnostic ultrasound systems and learn how to use these tools List of supporting vendors for HIFU and diagnostic ultrasound QC hands-on workshop: Philips Healthcare Alpinion Medical Systems Verasonics, Inc Zonare Medical Systems, Inc Computerized Imaging Reference Systems (CIRS), Inc. GAMMEX, Inc., Cablon Medical BV Steffen Sammet: NIH/NCI grant 5R25CA132822, NIH/NINDS grant 5R25NS

MO-AB-210-02: Ultrasound Imaging and Therapy-Hands On Workshop

Energy Technology Data Exchange (ETDEWEB)

Sammet, S. [University of Chicago Medical Center (United States)

2015-06-15

The goal of this ultrasound hands-on workshop is to demonstrate advancements in high intensity focused ultrasound (HIFU) and to demonstrate quality control (QC) testing in diagnostic ultrasound. HIFU is a therapeutic modality that uses ultrasound waves as carriers of energy. HIFU is used to focus a beam of ultrasound energy into a small volume at specific target locations within the body. The focused beam causes localized high temperatures and produces a well-defined regions of necrosis. This completely non-invasive technology has great potential for tumor ablation and targeted drug delivery. At the workshop, attendees will see configurations, applications, and hands-on demonstrations with on-site instructors at separate stations. The involvement of medical physicists in diagnostic ultrasound imaging service is increasing due to QC and accreditation requirements. At the workshop, an array of ultrasound testing phantoms and ultrasound scanners will be provided for attendees to learn diagnostic ultrasound QC in a hands-on environment with live demonstrations of the techniques. Target audience: Medical physicists and other medical professionals in diagnostic imaging and radiation oncology with interest in high-intensity focused ultrasound and in diagnostic ultrasound QC. Learning Objectives: Learn ultrasound physics and safety for HIFU applications through live demonstrations Get an overview of the state-of-the art in HIFU technologies and equipment Gain familiarity with common elements of a quality control program for diagnostic ultrasound imaging Identify QC tools available for testing diagnostic ultrasound systems and learn how to use these tools List of supporting vendors for HIFU and diagnostic ultrasound QC hands-on workshop: Philips Healthcare Alpinion Medical Systems Verasonics, Inc Zonare Medical Systems, Inc Computerized Imaging Reference Systems (CIRS), Inc. GAMMEX, Inc., Cablon Medical BV Steffen Sammet: NIH/NCI grant 5R25CA132822, NIH/NINDS grant 5R25NS

MO-AB-210-01: Ultrasound Imaging and Therapy-Hands On Workshop

Energy Technology Data Exchange (ETDEWEB)

Lu, Z. [University of Chicago (United States)

2015-06-15

The goal of this ultrasound hands-on workshop is to demonstrate advancements in high intensity focused ultrasound (HIFU) and to demonstrate quality control (QC) testing in diagnostic ultrasound. HIFU is a therapeutic modality that uses ultrasound waves as carriers of energy. HIFU is used to focus a beam of ultrasound energy into a small volume at specific target locations within the body. The focused beam causes localized high temperatures and produces a well-defined regions of necrosis. This completely non-invasive technology has great potential for tumor ablation and targeted drug delivery. At the workshop, attendees will see configurations, applications, and hands-on demonstrations with on-site instructors at separate stations. The involvement of medical physicists in diagnostic ultrasound imaging service is increasing due to QC and accreditation requirements. At the workshop, an array of ultrasound testing phantoms and ultrasound scanners will be provided for attendees to learn diagnostic ultrasound QC in a hands-on environment with live demonstrations of the techniques. Target audience: Medical physicists and other medical professionals in diagnostic imaging and radiation oncology with interest in high-intensity focused ultrasound and in diagnostic ultrasound QC. Learning Objectives: Learn ultrasound physics and safety for HIFU applications through live demonstrations Get an overview of the state-of-the art in HIFU technologies and equipment Gain familiarity with common elements of a quality control program for diagnostic ultrasound imaging Identify QC tools available for testing diagnostic ultrasound systems and learn how to use these tools List of supporting vendors for HIFU and diagnostic ultrasound QC hands-on workshop: Philips Healthcare Alpinion Medical Systems Verasonics, Inc Zonare Medical Systems, Inc Computerized Imaging Reference Systems (CIRS), Inc. GAMMEX, Inc., Cablon Medical BV Steffen Sammet: NIH/NCI grant 5R25CA132822, NIH/NINDS grant 5R25NS

High-power electron beam tests of a liquid-lithium target and characterization study of (7)Li(p,n) near-threshold neutrons for accelerator-based boron neutron capture therapy.

Science.gov (United States)

Halfon, S; Paul, M; Arenshtam, A; Berkovits, D; Cohen, D; Eliyahu, I; Kijel, D; Mardor, I; Silverman, I

2014-06-01

A compact Liquid-Lithium Target (LiLiT) was built and tested with a high-power electron gun at Soreq Nuclear Research Center (SNRC). The target is intended to demonstrate liquid-lithium target capabilities to constitute an accelerator-based intense neutron source for Boron Neutron Capture Therapy (BNCT) in hospitals. The lithium target will produce neutrons through the (7)Li(p,n)(7)Be reaction and it will overcome the major problem of removing the thermal power >5kW generated by high-intensity proton beams, necessary for sufficient therapeutic neutron flux. In preliminary experiments liquid lithium was flown through the target loop and generated a stable jet on the concave supporting wall. Electron beam irradiation demonstrated that the liquid-lithium target can dissipate electron power densities of more than 4kW/cm(2) and volumetric power density around 2MW/cm(3) at a lithium flow of ~4m/s, while maintaining stable temperature and vacuum conditions. These power densities correspond to a narrow (σ=~2mm) 1.91MeV, 3mA proton beam. A high-intensity proton beam irradiation (1.91-2.5MeV, 2mA) is being commissioned at the SARAF (Soreq Applied Research Accelerator Facility) superconducting linear accelerator. In order to determine the conditions of LiLiT proton irradiation for BNCT and to tailor the neutron energy spectrum, a characterization of near threshold (~1.91MeV) (7)Li(p,n) neutrons is in progress based on Monte-Carlo (MCNP and Geant4) simulation and on low-intensity experiments with solid LiF targets. In-phantom dosimetry measurements are performed using special designed dosimeters based on CR-39 track detectors. © 2013 Elsevier Ltd. All rights reserved.

Progress in target materials for high-efficiency X-ray backlight

International Nuclear Information System (INIS)

Du Ai; Zhou Bin; Li Longxiang; Zhu Xiurong; Li Yu'nong; Shen Jun; Gao Guohua; Zhang Zhihua; Wu Guangming

2012-01-01

The composition, microstructure and density of the target materials are the key parameters to determinate the photon energy and intensity of the laser-induced X-ray backlight. Thus the classification of backlight targets, the preparation of target materials and the interaction between targets and high power laser were introduced in this paper. Underdense targets were more competitive than traditional dense targets among the backlight targets. Nano-structured foam targets, which could be classified into nanofiber targets and aerogel targets, were regarded as novel high-efficiency underdense targets. Nanofiber, which was commonly prepared via electro spinning and thermal treatment, exhibited good formability and high concentration of emission atoms; while aerogel, which was prepared via sol-gel processes and supercritical fluid drying, possesses the advantages of homogeneous microstructure and theoretically high conversion efficiency, but accompanied with the disadvantages of complex synthetic processes and low concentration of emission atoms. To prepare monolithic aerogels with low density and high concentration of emission atoms via combined sol-gel theories may be the better design for the development of the laser-induced X-ray backlight. (authors)

Summary of workshop on high temperature materials based on Laves phases

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-08-01

The Offices of Fossil Energy and Basic Energy Sciences of the Department of Energy jointly sponsored the Workshop on High Temperature Materials Based on Laves Phases in conjunction with the Tenth Annual Conference on Fossil Energy Materials held at the Radisson Summit Hill Hotel in Knoxville, Tennessee on May 14-16, 1996. The objective of this workshop was to review the current status and to address critical issues in the development of new-generation high-temperature structural materials based on Laves phases. The one-day workshop included two sessions of overview presentations and a session of discussion on critical scientific and technological issues. The Laves phases represent an abundant class of intermetallic alloys with possible high-temperature structural applications. Laves phases form at or near the AB{sub 2} composition, and there are over 360 binary Laves phases. The ability of these alloys to dissolve considerable amounts of ternary alloying additions provides over 900 combined binary and ternary Laves phases. Many Laves phases have unique properties which make them attractive for high-temperature structural use. At half their homologous temperature, they retain >0.85 of their ambient yield strength, which is higher than all other intermetallics. Many of the Laves phases also have high melting temperatures, excellent creep properties, reasonably low densities, and for alloys containing Cr, Al, Si or Be, good oxidation resistance. Despite these useful properties, the tendency for low-temperature brittleness has limited the potential application of this large class of alloys.

Proceedings of 6th International Microbeam Workshop/12th L.H. Gray Workshop Microbeam Probes of Cellular Radiation Response

International Nuclear Information System (INIS)

Prise, Kevin M.

2004-01-01

The extended abstracts which are submitted here present a summary of the proceedings of the 6th International Workshop/12th LH Gray Workshop: Microbeam Probes of Cellular Radiation Response, held at St. Catherine's College, University of Oxford, UK on March, 29th-31st, 2003. In 1993 the 4th LH Gray Workshop entitled ''Microbeam Probes of Cellular Radiation Response'' was held at the Gray Cancer Institute in Northwood. This was organized by Prof BD Michael, Dr M. Folkard and Dr KM Prise and brought together 40 participants interested in developing and applying new microbeam technology to problems in radiation biology (1). The workshop was an undoubted success and has spawned a series of subsequent workshops every two years. In the past, these workshops have been highly successful in bringing together groups interested in developing and applying micro-irradiation techniques to the study of cell and tissue damage by ionizing radiations. Following the first microbeam workshop, there has been a rapid growth in the number of centres developing radiobiology microbeams, or planning to do so and there are currently 15-20 worldwide. Much of the recent research using microbeams has used them to study low-dose effects and ''non-targeted'' responses such bystander effects, genomic instability and adaptive responses. The goal of the 6th workshop was to build on our knowledge of the development of microbeam approaches and the application to radiation biology in the future with the meeting stretching over a 3 day period. Over 80 participants reviewed the current state of radiobiology microbeam research worldwide and reported on new technological developments both in the fields of physics and biology

Winning Hearts and Minds: Inspiring Medical Students into Cardiothoracic Surgery Through Highly Interactive Workshops.

Science.gov (United States)

George, Joseph; Combellack, Tom; Lopez-Marco, Ana; Aslam, Umair; Ahmed, Yasir; Nanjaiah, Prakash; Youhana, Aprim; Kumar, Pankaj

The cardiothoracic surgical (CTS) specialty has witnessed a decline in the applicant pool. Early exposure, positive experiences, inspiring role models, and career insight are key in the decision-making process for specialty choice. Our objective was to assess the effect of high tutor:student ratio interactive CTS workshops in influencing the career choice of UK undergraduate medical students. Medical students attended a workshop comprising (1) guided dissection of fresh animal hearts, (2) surgical skills practice on models and fresh hearts, (3) operative videos (adult, congenital, transplant, and aortic) with interactive commentary, and (4) careers seminar. The tutor:student ratio was very high (between 3-1 and 5-1). A questionnaire was completed at the end of each workshop to assess its effect, including a 10-point Likert scale on the perceived attraction to CTS before and after the workshop. A total of 96 delegates attended 5 workshops in 3 UK medical schools. Response rate was 83% from 80 undergraduate students. In all, 58% were male (46/80). There was an equal proportion of sexes in the early years of medical school, but was significantly skewed toward male in the later years. There was a statistically significant increase of 2.1 (standard deviation [SD] = 1.5) in the Likert scores before (μ = 5.0, SD = 2.1) and after (μ = 7.1, SD = 1.9) (p = 0.001). This represents a 42% increase in the perceived attraction to the CTS specialty because of the workshops. Our workshops have a significant effect in stimulating undergraduate medical students toward a career in cardiothoracic surgery. We encourage national take-up of these easily organized daylong workshops to foster interest in the next generation of cardiothoracic surgeons. Copyright © 2017 Association of Program Directors in Surgery. Published by Elsevier Inc. All rights reserved.

Workshop for middle school and high school educators

International Nuclear Information System (INIS)

Miller, D.W.

1992-01-01

This paper summarizes the workshop entitled, 'Understanding and Teaching about Nuclear Technology and Its Place in Our Society' presented at Ohio State University (OSU) in August 1991. The workshop was a collaborative program with the American Nuclear Society (ANS) taking the lead and OSU taking a supportive and facilitator role. The paper addresses the issues of program management and development. Because the program elements provided by the ANS are generic to other workshops they have sponsored, only the unique contributions made by OSU are discussed

Alternate fusion fuels workshop

International Nuclear Information System (INIS)

1981-06-01

The workshop was organized to focus on a specific confinement scheme: the tokamak. The workshop was divided into two parts: systems and physics. The topics discussed in the systems session were narrowly focused on systems and engineering considerations in the tokamak geometry. The workshop participants reviewed the status of system studies, trade-offs between d-t and d-d based reactors and engineering problems associated with the design of a high-temperature, high-field reactor utilizing advanced fuels. In the physics session issues were discussed dealing with high-beta stability, synchrotron losses and transport in alternate fuel systems. The agenda for the workshop is attached

Transgender HIV prevention: implementation and evaluation of a workshop.

Science.gov (United States)

Bockting, W O; Rosser, B R; Scheltema, K

1999-04-01

Virtually no HIV prevention education has specifically targeted the transgender community. To fill this void, a transgender HIV prevention workshop was developed, implemented and evaluated. A 4 h workshop, grounded in the Health Belief Model and the Eroticizing Safer Sex approach, combined lectures, videos, a panel, discussion, roleplay and exercises. Evaluation using a pre-, post- and follow-up test design showed an increase in knowledge and an initial increase in positive attitudes that diminished over time. Due to the small sample size (N = 59) and limited frequency of risk behavior, a significant decrease in unsafe sexual or needle practices could not be demonstrated. However, findings suggested an increase in safer sexual behaviors such as (mutual) masturbation. Peer support improved significantly. Future prevention education should make special efforts to target the more difficult-to-reach, high-risk subgroups of the transgender population.

Workshop on the AGS fixed-target research program

Energy Technology Data Exchange (ETDEWEB)

Ahrens, L; Schewe, P; Wanderer, P; Weisberg, H [eds.

1978-01-01

The summarized results of a two day workshop to determine experiment programs for the Brookhaven AGS during the construction period of the ISABELLE storage rings and after are presented. Topics covered include: experiments with low-energy beams; experiments with higher energy beams; neutrino physics; and polarized protons. (GHT)

Proceedings of the fifth workshop on containment integrity

Energy Technology Data Exchange (ETDEWEB)

Parks, M.B.; Hughey, C.E. [eds.] [Sandia National Labs., Albuquerque, NM (United States)

1992-07-01

The Fifth Workshop on Containment integrity was held in Washington, DC, on May 12--14, 1992. The purpose of these workshops is to provide an international forum for the exchange of information on performance of containments in nuclear power plants under severe accident loadings. Severe accident investigations of existing containment designs as well as future advanced containments were presented during the workshop. There were 145 participants at the workshop from 15 countries. Individual papers have been cataloged separately.

Measurement of total ultrasonic power using thermal expansion and change in buoyancy of an absorbing target.

Science.gov (United States)

Dubey, P K; Kumar, Yudhisther; Gupta, Reeta; Jain, Anshul; Gohiya, Chandrashekhar

2014-05-01

The Radiation Force Balance (RFB) technique is well established and most widely used for the measurement of total ultrasonic power radiated by ultrasonic transducer. The technique is used as a primary standard for calibration of ultrasonic transducers with relatively fair uncertainty in the low power (below 1 W) regime. In this technique, uncertainty comparatively increases in the range of few watts wherein the effects such as thermal heating of the target, cavitations, and acoustic streaming dominate. In addition, error in the measurement of ultrasonic power is also caused due to movement of absorber at relatively high radiated force which occurs at high power level. In this article a new technique is proposed which does not measure the balance output during transducer energized state as done in RFB. It utilizes the change in buoyancy of the absorbing target due to local thermal heating. The linear thermal expansion of the target changes the apparent mass in water due to buoyancy change. This forms the basis for the measurement of ultrasonic power particularly in watts range. The proposed method comparatively reduces uncertainty caused by various ultrasonic effects that occur at high power such as overshoot due to momentum of target at higher radiated force. The functionality of the technique has been tested and compared with the existing internationally recommended RFB technique.

Measurement of total ultrasonic power using thermal expansion and change in buoyancy of an absorbing target

Science.gov (United States)

Dubey, P. K.; Kumar, Yudhisther; Gupta, Reeta; Jain, Anshul; Gohiya, Chandrashekhar

2014-05-01

The Radiation Force Balance (RFB) technique is well established and most widely used for the measurement of total ultrasonic power radiated by ultrasonic transducer. The technique is used as a primary standard for calibration of ultrasonic transducers with relatively fair uncertainty in the low power (below 1 W) regime. In this technique, uncertainty comparatively increases in the range of few watts wherein the effects such as thermal heating of the target, cavitations, and acoustic streaming dominate. In addition, error in the measurement of ultrasonic power is also caused due to movement of absorber at relatively high radiated force which occurs at high power level. In this article a new technique is proposed which does not measure the balance output during transducer energized state as done in RFB. It utilizes the change in buoyancy of the absorbing target due to local thermal heating. The linear thermal expansion of the target changes the apparent mass in water due to buoyancy change. This forms the basis for the measurement of ultrasonic power particularly in watts range. The proposed method comparatively reduces uncertainty caused by various ultrasonic effects that occur at high power such as overshoot due to momentum of target at higher radiated force. The functionality of the technique has been tested and compared with the existing internationally recommended RFB technique.

Measurement of total ultrasonic power using thermal expansion and change in buoyancy of an absorbing target

International Nuclear Information System (INIS)

Dubey, P. K.; Kumar, Yudhisther; Gupta, Reeta; Jain, Anshul; Gohiya, Chandrashekhar

2014-01-01

The Radiation Force Balance (RFB) technique is well established and most widely used for the measurement of total ultrasonic power radiated by ultrasonic transducer. The technique is used as a primary standard for calibration of ultrasonic transducers with relatively fair uncertainty in the low power (below 1 W) regime. In this technique, uncertainty comparatively increases in the range of few watts wherein the effects such as thermal heating of the target, cavitations, and acoustic streaming dominate. In addition, error in the measurement of ultrasonic power is also caused due to movement of absorber at relatively high radiated force which occurs at high power level. In this article a new technique is proposed which does not measure the balance output during transducer energized state as done in RFB. It utilizes the change in buoyancy of the absorbing target due to local thermal heating. The linear thermal expansion of the target changes the apparent mass in water due to buoyancy change. This forms the basis for the measurement of ultrasonic power particularly in watts range. The proposed method comparatively reduces uncertainty caused by various ultrasonic effects that occur at high power such as overshoot due to momentum of target at higher radiated force. The functionality of the technique has been tested and compared with the existing internationally recommended RFB technique

1995 NASA High-Speed Research Program Sonic Boom Workshop. Volume 2; Configuration Design, Analysis, and Testing

Science.gov (United States)

Baize, Daniel G. (Editor)

1999-01-01

The High-Speed Research Program and NASA Langley Research Center sponsored the NASA High-Speed Research Program Sonic Boom Workshop on September 12-13, 1995. The workshop was designed to bring together NASAs scientists and engineers and their counterparts in industry, other Government agencies, and academia working together in the sonic boom element of NASAs High-Speed Research Program. Specific objectives of this workshop were to: (1) report the progress and status of research in sonic boom propagation, acceptability, and design; (2) promote and disseminate this technology within the appropriate technical communities; (3) help promote synergy among the scientists working in the Program; and (4) identify technology pacing, the development C, of viable reduced-boom High-Speed Civil Transport concepts. The Workshop was organized in four sessions: Sessions 1 Sonic Boom Propagation (Theoretical); Session 2 Sonic Boom Propagation (Experimental); Session 3 Acceptability Studies-Human and Animal; and Session 4 - Configuration Design, Analysis, and Testing.

Working material. IAEA seismic safety of nuclear power plants. International workshop on lessons learned from strong earthquake

International Nuclear Information System (INIS)

2008-08-01

The International Workshop on Lessons Learned from Strong Earthquake was held at Kashiwazaki civic plaza, Kashiwazaki, Niigata-prefecture, Japan, for three days in June 2008. Kashiwazaki-Kariwa NPP (KK-NPP) is located in the city of Kashiwazaki and the village of Kariwa, and owned and operated by Tokyo Electric Power Company Ltd. (TEPCO). After it experienced the Niigata-ken Chuetsu-oki earthquake in July 2007, IAEA dispatched experts' missions twice and held technical discussions with TEPCO. Through such activities, the IAEA secretariat and experts obtained up-dated information of plant integrity, geological and seismological evaluation and developments of the consultation in the regulatory framework of Japan. Some of the information has been shared with the member states through the reports on findings and lessons learned from the missions to Japan. The international workshop was held to discuss and share the information of lessons learned from strong earthquakes in member states' nuclear installations. It provided the opportunity for participants from abroad to share the information of the recent earthquake and experience in Japan and to visit KK-NPP. And for experts in Japan, the workshop provided the opportunity to share the international approach on seismic-safety-related measures and experiences. The workshop was organised by the IAEA as a part of an extra budgetary project, in cooperation with OECD/NEA, hosted by Japanese organisations including Nuclear and Industrial Safety Agency (NISA), Nuclear Safety Commission (NSC), and Japan Nuclear Energy Safety Organization (JNES). The number of the workshop participants was 70 experts from outside Japan, 27 countries and 2 international organisations, 154 Japanese experts and 81 audience and media personnel, totalling to 305 participants. The three-day workshop was open to the media including the site visit, and covered by NHK (the nation's public broadcasting corporation) and nation-wide and local television

A Workshop for High School Students on Naive Set Theory

Science.gov (United States)

Wegner, Sven-Ake

2014-01-01

In this article we present the prototype of a workshop on naive set theory designed for high school students in or around the seventh year of primary education. Our concept is based on two events which the author organized in 2006 and 2010 for students of elementary school and high school, respectively. The article also includes a practice report…

European Workshop on High Order Nonlinear Numerical Schemes for Evolutionary PDEs

CERN Document Server

Beaugendre, Héloïse; Congedo, Pietro; Dobrzynski, Cécile; Perrier, Vincent; Ricchiuto, Mario

2014-01-01

This book collects papers presented during the European Workshop on High Order Nonlinear Numerical Methods for Evolutionary PDEs (HONOM 2013) that was held at INRIA Bordeaux Sud-Ouest, Talence, France in March, 2013. The central topic is high order methods for compressible fluid dynamics. In the workshop, and in this proceedings, greater emphasis is placed on the numerical than the theoretical aspects of this scientific field. The range of topics is broad, extending through algorithm design, accuracy, large scale computing, complex geometries, discontinuous Galerkin, finite element methods, Lagrangian hydrodynamics, finite difference methods and applications and uncertainty quantification. These techniques find practical applications in such fields as fluid mechanics, magnetohydrodynamics, nonlinear solid mechanics, and others for which genuinely nonlinear methods are needed.

1998 federal technical standards workshop: Proceedings

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-10-01

The theme for the 1998 workshop was Standards Management -- A World of Change and Opportunities. The workshop`s goal was to further the implementation of the National Technology Transfer and Advancement Act of 1995 (Public Law 104-113) through the sharing of standards management success stories, lessons learned, and emerging initiatives within the Executive Branch of the Federal Government. The target audience for this workshop included agency/department and contractor personnel and representatives of standards developing organizations that either used technical standards in their work for the Federal Government of participated in standards writing/management activities in support of the missions and programs of Federal agencies/departments. As with previous standards workshops sponsored by the DOE, views on the technical subject areas under the workshop theme were solicited from and provided by agency Standards Executives and standards program managers, voluntary standards organizations, and the private sector. This report includes vugraphs of the presentations.

14. International workshop on nuclear fission physics. Proceedings

International Nuclear Information System (INIS)

2000-01-01

The meetings on nuclear fission took place 12-15 October 1998 and was organized by Institute of Physics and Power Engineering. The aim of the workshop was to present and discuss main new both theoretical and experimental results obtained in the area of nuclear fission, dynamical feature, properties of fission fragments and complementary radiation. As usual the program of the workshop was designed to cover a wide range of physical phenomena - from low energy and spontaneous fission to fission of hot rotating nuclei and multifragmentation at intermediate and high energies. Reaction induced by slow and fast neutron, light and heavy ions were discussed [ru

Proceedings of RIKEN BNL Research Center Workshop: Progress in High-pT Physics at RHIC

Energy Technology Data Exchange (ETDEWEB)

Bazilevsky, A.; Bland, L.; Vogelsang, W.

2010-03-17

This volume archives the presentations at the RIKEN BNL Research Center workshop 'Progress in High-PT Physics at RHIC', held at BNL in March 2010. Much has been learned from high-p{sub T} physics after 10 years of RHIC operations for heavy-ion collisions, polarized proton collisions and d+Au collisions. The workshop focused on recent progress in these areas by both theory and experiment. The first morning saw review talks on the theory of RHIC high-p{sub T} physics by G. Sterman and J. Soffer, and on the experimental results by M. Tannenbaum. One of the most exciting recent results from the RHIC spin program is the first observation of W bosons and their associated single-spin asymmetry. The new preliminary data were reported on the first day of our workshop, along with a theoretical perspective. There also were detailed discussions on the global analysis of polarized parton distributions, including the knowledge on gluon polarization and the impact of the W-data. The main topic of the second workshop day were single-transverse spin asymmetries and their analysis in terms of transverse-momentum dependent parton distributions. There is currently much interest in a future Drell-Yan program at RHIC, thanks to the exciting physics opportunities this would offer. This was addressed in some of the talks. There also were presentations on the latest results on transverse-spin physics from HERMES and BELLE. On the final day of the workshop, the focus shifted toward forward and small-x physics at RHIC, which has become a cornerstone of the whole RHIC program. Exciting new data were presented and discussed in terms of their possible implications for our understanding of strong color-field phenomena in QCD. In the afternoon, there were discussions of nuclear parton distributions and jet observables, among them fragmentation. The workshop was concluded with outlooks toward the near-term (LHC, JLab) and longer-term (EIC) future. The workshop has been a great success

Report on the B-Fields at NIF Workshop Held at LLNL October 12-13, 2015

International Nuclear Information System (INIS)

Fournier, K. B.; Moody, J. D.

2015-01-01

A national ICF laboratory workshop on requirements for a magnetized target capability on NIF was held by NIF at LLNL on October 12 and 13, attended by experts from LLNL, SNL, LLE, LANL, GA, and NRL. Advocates for indirect drive (LLNL), magnetic (Z) drive (SNL), polar direct drive (LLE), and basic science needing applied B (many institutions) presented and discussed requirements for the magnetized target capabilities they would like to see. 30T capability was most frequently requested. A phased operation increasing the field in steps experimentally can be envisioned. The NIF management will take the inputs from the scientific community represented at the workshop and recommend pulse-powered magnet parameters for NIF that best meet the collective user requests. In parallel, LLNL will continue investigating magnets for future generations that might be powered by compact laser-B-field generators (Moody, Fujioka, Santos, Woolsey, Pollock). The NIF facility engineers will start to analyze compatibility of the recommended pulsed magnet parameters (size, field, rise time, materials) with NIF chamber constraints, diagnostic access, and final optics protection against debris in FY16. The objective of this assessment will be to develop a schedule for achieving an initial Bfield capability. Based on an initial assessment, room temperature magnetized gas capsules will be fielded on NIF first. Magnetized cryo-ice-layered targets will take longer (more compatibility issues). Magnetized wetted foam DT targets (Olson) may have somewhat fewer compatibility issues making them a more likely choice for the first cryo-ice-layered target fielded with applied Bz.

Report from the NSLS workshop: Sources and applications of high intensity uv-vuv light

Energy Technology Data Exchange (ETDEWEB)

Johnson, E.D.; Hastings, J.B. (eds.)

1990-01-01

A workshop was held to evaluate sources and applications of high intensity, ultra violet (UV) radiation for biological, chemical, and materials sciences. The proposed sources are a UV free electron laser (FEL) driven by a high brightness linac and undulators in long, straight sections of a specially designed low energy (400 MeV) storage ring. These two distinct types of sources will provide a broad range of scientific opportunities that were discussed in detail during the workshop.

Report from the NSLS workshop: Sources and applications of high intensity uv-vuv light

Energy Technology Data Exchange (ETDEWEB)

Johnson, E.D.; Hastings, J.B. [eds.

1990-12-31

A workshop was held to evaluate sources and applications of high intensity, ultra violet (UV) radiation for biological, chemical, and materials sciences. The proposed sources are a UV free electron laser (FEL) driven by a high brightness linac and undulators in long, straight sections of a specially designed low energy (400 MeV) storage ring. These two distinct types of sources will provide a broad range of scientific opportunities that were discussed in detail during the workshop.

Report from the NSLS workshop: Sources and applications of high intensity uv-vuv light

International Nuclear Information System (INIS)

Johnson, E.D.; Hastings, J.B.

1990-01-01

A workshop was held to evaluate sources and applications of high intensity, ultra violet (UV) radiation for biological, chemical, and materials sciences. The proposed sources are a UV free electron laser (FEL) driven by a high brightness linac and undulators in long, straight sections of a specially designed low energy (400 MeV) storage ring. These two distinct types of sources will provide a broad range of scientific opportunities that were discussed in detail during the workshop

Public Benefits and Power Sector Reform. Report from an International Workshop

Energy Technology Data Exchange (ETDEWEB)

Nilsson, Lars J.; Arvidson, Anders; Eberhard, Anton (eds.)

2003-10-01

The Workshop on Public Benefits and Power Sector Reform was motivated by the need to address broader development goals and advance the provision of public benefits in power sector reforms. The primary objectives were: To provide a forum for a discussion among specialists, of how the provision of public benefits can be expanded as power sectors in developing countries are reformed, and review the experience (Day 1). To identify the needs for training and capacity building and institutional arrangements, as well as make recommendations for their design and implementation, for policy makers, regulators, and other professionals in developing countries (Day 2). Public benefits is a socially constructed concept that includes activities that are not adequately conceived by competitive markets. Public benefit policies and programmes include those that expand electricity access to rural areas and the urban poor, improve security of supply, promote energy efficiency and renewable energy, etc. Reforms have indeed been a threat to public benefits as traditionally delivered through electric utilities. However, in many cases public benefit programmes have also been rescued. In fewer cases, public benefit programmes have been conceived in the reform process. From experience so far it is clear that power sector reforms must be made more compatible with broader sustainable development goals. Recognising the need for broader policy integration and putting public benefits higher on the reform agenda points to the importance of reaching beyond energy ministries and power sector experts at an early stage in the reform process. Other actors, such as NGOs and academia, may also be instrumental in monitoring and assessing the impacts of reform. Public benefits can be an integral part of a reform package, or a complement to reform. It does appear that reform creates space and opportunity to achieve public benefits, but someone has to utilise that opportunity. The need to make trade

Public Benefits and Power Sector Reform. Report from an International Workshop

International Nuclear Information System (INIS)

Nilsson, Lars J.; Arvidson, Anders; Eberhard, Anton

2003-10-01

The Workshop on Public Benefits and Power Sector Reform was motivated by the need to address broader development goals and advance the provision of public benefits in power sector reforms. The primary objectives were: To provide a forum for a discussion among specialists, of how the provision of public benefits can be expanded as power sectors in developing countries are reformed, and review the experience (Day 1). To identify the needs for training and capacity building and institutional arrangements, as well as make recommendations for their design and implementation, for policy makers, regulators, and other professionals in developing countries (Day 2). Public benefits is a socially constructed concept that includes activities that are not adequately conceived by competitive markets. Public benefit policies and programmes include those that expand electricity access to rural areas and the urban poor, improve security of supply, promote energy efficiency and renewable energy, etc. Reforms have indeed been a threat to public benefits as traditionally delivered through electric utilities. However, in many cases public benefit programmes have also been rescued. In fewer cases, public benefit programmes have been conceived in the reform process. From experience so far it is clear that power sector reforms must be made more compatible with broader sustainable development goals. Recognising the need for broader policy integration and putting public benefits higher on the reform agenda points to the importance of reaching beyond energy ministries and power sector experts at an early stage in the reform process. Other actors, such as NGOs and academia, may also be instrumental in monitoring and assessing the impacts of reform. Public benefits can be an integral part of a reform package, or a complement to reform. It does appear that reform creates space and opportunity to achieve public benefits, but someone has to utilise that opportunity. The need to make trade

The Astronomy Workshop

Science.gov (United States)

Hamilton, D. P.

2005-05-01

The Astronomy Workshop (http://janus.astro.umd.edu) is a collection of interactive online educational tools developed for use by students, educators, and the general public. The more than 20 tools in the Astronomy Workshop are rated for ease-of-use, and have been extensively tested in large university survey courses, classes for undergraduate majors, and High Schools. Here we briefly describe a few of the more popular tools. The Life of the Sun (New!): The history of the Sun is animated as a movie, showing students how the size and color of our star has evolved and will evolve in time. Animated Orbits of Planets and Moons: The orbital motions of planets, moons, asteroids, and comets are animated at their correct relative speeds in accurate to-scale drawings. Solar System Collisions: This most popular of our applications shows what happens when an asteroid or comet with user-defined size and speed impacts a given planet. The program calculates many effects, including the country of impact (if Earth is the target), energy of explosion, crater size, and magnitude of the ``planetquake'' generated. It also displays a relevant image (e.g. terrestrial crater, lunar crater, etc.). Astronomical Distances: Travel away from the Earth at a chosen speed and see how long it takes to reach other planets, stars and galaxies. This tool helps students visualize astronomical distances in an intuitive way. Funding for the Astronomy Workshop is provided by a NASA EPO grant.

Technical Meeting/Workshop on Topical Issues on Infrastructure Development: Managing the Development of a National Infrastructure for Nuclear Power Plants. Presentations

International Nuclear Information System (INIS)

2012-01-01

The main purpose of the TM/Workshop is to provide an opportunity for exchange of specific information on the management of the development of a sustainable national infrastructure for Nuclear Power Plants as it is recommended in the Agency's Milestones approach. Taking into account the actual status of new nuclear power programmes in Member States, this Agency event shall focus on the moving beyond the consideration of the nuclear power and advancing to the next phase, when future partners (Consultants, NPP Vendors, EPC Contractors, etc.) shall be selected and contracted for the first Nuclear Power Plant. The objectives of the Technical Meeting/Workshop are the following: 1. To exchange specific information and to facilitate the management and coordination of the development and implementation of a national infrastructure for nuclear power; 2. To present and discuss case studies, good practices and lessons learned about recent experiences in implementing an appropriate infrastructure for nuclear power, including management methods and self-evaluation processes; 3. To allow participants to improve their knowledge of various aspects of nuclear infrastructure development; and 4. To provide a forum in which participants can discuss common challenges, opportunities for cooperation, concerns and issues their countries face in the infrastructure implementation process.

HTTR workshop (workshop on hydrogen production technology)

International Nuclear Information System (INIS)

Shiina, Yasuaki; Takizuka, Takakazu

2004-12-01

Various research and development efforts have been performed to solve the global energy and environmental problems caused by large consumption of fossil fuels. Research activities on advanced hydrogen production technology by the use of nuclear heat from high temperature gas cooled reactors, for example, have been flourished in universities, research institutes and companies in many countries. The Department of HTTR Project and the Department of Advanced Nuclear Heat Technology of JAERI held the HTTR Workshop (Workshop on Hydrogen Production Technology) on July 5 and 6, 2004 to grasp the present status of R and D about the technology of HTGR and the nuclear hydrogen production in the world and to discuss about necessity of the nuclear hydrogen production and technical problems for the future development of the technology. More than 110 participants attended the Workshop including foreign participants from USA, France, Korea, Germany, Canada and United Kingdom. In the Workshop, the presentations were made on such topics as R and D programs for nuclear energy and hydrogen production technologies by thermo-chemical or other processes. Also, the possibility of the nuclear hydrogen production in the future society was discussed. The workshop showed that the R and D for the hydrogen production by the thermo-chemical process has been performed in many countries. The workshop affirmed that nuclear hydrogen production could be one of the competitive supplier of hydrogen in the future. The second HTTR Workshop will be held in the autumn next year. (author)

Research results for the applications of high power ion beams

International Nuclear Information System (INIS)

Yang Hailiang; Qiu Aici; Sun Jianfeng; He Xiaoping; Tang Junping; Wang Haiyang; Zhang Jiasheng; Xu Ri; Peng Jianchang; Ren Shuqing; Li Peng; Yang Li; Huang Jianjun; Zhang Guoguang; Ouyang Xiaoping; Li Hongyu

2003-01-01

The results obtained in the theoretical and experimental studies for the application of high power ion beams in certain areas of nuclear physics and material science are reported. The preliminary experimental results of generating 6-7 MeV quasi-monoenergetic pulsed γ-rays with high power pulsed proton beams striking 19 F target on the Flash II accelerator are presented. By placing the target far enough downstream, the quasi-monoenergetic pulsed γ-rays can be discriminated experimentally from the diode Bremsstrahlung. This article also describes the other applications of high power ion beams and the preliminary experimental and theoretical results in simulation of soft X-ray thermal-mechanical effects, generation of high intense pulsed neutrons, equation of state and shock-wave physics experiments, surface modification and so on

Dynamic defense workshop :

Energy Technology Data Exchange (ETDEWEB)

Crosby, Sean Michael; Doak, Justin E.; Haas, Jason Juedes.; Helinski, Ryan; Lamb, Christopher C.

2013-02-01

On September 5th and 6th, 2012, the Dynamic Defense Workshop: From Research to Practice brought together researchers from academia, industry, and Sandia with the goals of increasing collaboration between Sandia National Laboratories and external organizations, de ning and un- derstanding dynamic, or moving target, defense concepts and directions, and gaining a greater understanding of the state of the art for dynamic defense. Through the workshop, we broadened and re ned our de nition and understanding, identi ed new approaches to inherent challenges, and de ned principles of dynamic defense. Half of the workshop was devoted to presentations of current state-of-the-art work. Presentation topics included areas such as the failure of current defenses, threats, techniques, goals of dynamic defense, theory, foundations of dynamic defense, future directions and open research questions related to dynamic defense. The remainder of the workshop was discussion, which was broken down into sessions on de ning challenges, applications to host or mobile environments, applications to enterprise network environments, exploring research and operational taxonomies, and determining how to apply scienti c rigor to and investigating the eld of dynamic defense.

Developing workshop module of realistic mathematics education: Follow-up workshop

Science.gov (United States)

Palupi, E. L. W.; Khabibah, S.

2018-01-01

Realistic Mathematics Education (RME) is a learning approach which fits the aim of the curriculum. The success of RME in teaching mathematics concepts, triggering students’ interest in mathematics and teaching high order thinking skills to the students will make teachers start to learn RME. Hence, RME workshop is often offered and done. This study applied development model proposed by Plomp. Based on the study by RME team, there are three kinds of RME workshop: start-up workshop, follow-up workshop, and quality boost. However, there is no standardized or validated module which is used in that workshops. This study aims to develop a module of RME follow-up workshop which is valid and can be used. Plopm’s developmental model includes materials analysis, design, realization, implementation, and evaluation. Based on the validation, the developed module is valid. While field test shows that the module can be used effectively.

Workshop proceedings of ISAMM 2009: Implementation of severe accident management measures

International Nuclear Information System (INIS)

Guentay, S.

2010-10-01

This comprehensive report published by the Paul Scherrer Institute (PSI) in Switzerland reports on a conference and workshop held in Switzerland in October 2009 dealing with Severe Accidents Management (SAM) in nuclear power stations. The workshop provided an update on the status of severe accident management measures and their implications since the OECD/CSNI workshop held in 2001 at the PSI in Switzerland. Since the 2001 workshop, additional work has been performed to integrate emergency procedures and SAM measures into risk assessments in order to better reflect operator responses to recover a plant from a damaged state. The major focus of the workshop was to address SAM measures for both operational plants and new plant designs. Also, the integration of SAM measures into contemporary/future probabilistic risk assessments was discussed. 41 papers were presented in 8 sessions. The papers addressed the following areas: 1) Current status and insights of SAM (2 sessions); 2) Probabilistic Safety Assessment (PSA) modelling issues; 3) code analysis for supporting Serious Accident Management Guidance (SAMG, 2 sessions); 4) decision making, tools, training, risk-targets and entrance to SAM; 5) design modifications for implementation of SAM; 6) physical phenomena. The last part of the workshop was devoted to the presentation of the most striking highlights of the papers in the above areas, followed by two panellists giving presentations on human and organisational aspects of SAM, their importance in relation to technical issues and the effectiveness of current SAMG implementation. The question of how consequence analyses can be used to improve the effectiveness of SAM is discussed. The contributions were presented by representatives from Austria, Germany, Japan, France, the USA, Korea, Switzerland, Finland, Hungary, Belgium, Canada, Sweden, the Czech republic, the United kingdom, the Netherlands, Spain, Slovenia and Russia. The authors state that the overall picture

Workshop proceedings of ISAMM 2009: Implementation of severe accident management measures

Energy Technology Data Exchange (ETDEWEB)

Guentay, S. (ed.) [Paul Scherrer Institute (PSI), Nuclear Energy and Safety Research Department, Laboratory for Thermal Hydraulics, ViIligen (Switzerland)

2010-10-15

This comprehensive report published by the Paul Scherrer Institute (PSI) in Switzerland reports on a conference and workshop held in Switzerland in October 2009 dealing with Severe Accidents Management (SAM) in nuclear power stations. The workshop provided an update on the status of severe accident management measures and their implications since the OECD/CSNI workshop held in 2001 at the PSI in Switzerland. Since the 2001 workshop, additional work has been performed to integrate emergency procedures and SAM measures into risk assessments in order to better reflect operator responses to recover a plant from a damaged state. The major focus of the workshop was to address SAM measures for both operational plants and new plant designs. Also, the integration of SAM measures into contemporary/future probabilistic risk assessments was discussed. 41 papers were presented in 8 sessions. The papers addressed the following areas: 1) Current status and insights of SAM (2 sessions); 2) Probabilistic Safety Assessment (PSA) modelling issues; 3) code analysis for supporting Serious Accident Management Guidance (SAMG, 2 sessions); 4) decision making, tools, training, risk-targets and entrance to SAM; 5) design modifications for implementation of SAM; 6) physical phenomena. The last part of the workshop was devoted to the presentation of the most striking highlights of the papers in the above areas, followed by two panellists giving presentations on human and organisational aspects of SAM, their importance in relation to technical issues and the effectiveness of current SAMG implementation. The question of how consequence analyses can be used to improve the effectiveness of SAM is discussed. The contributions were presented by representatives from Austria, Germany, Japan, France, the USA, Korea, Switzerland, Finland, Hungary, Belgium, Canada, Sweden, the Czech republic, the United kingdom, the Netherlands, Spain, Slovenia and Russia. The authors state that the overall picture

Technology Issues and Benefits of a Fast Ignition Power Plant with Cone Targets

International Nuclear Information System (INIS)

Hogan, W J; Meier, W R

2003-01-01

The use of cone focus, fast ignition targets, either for direct or indirect drive, promises to lower the required driver size and relax the symmetry requirements in IFE power plants. It may also allow use of chamber concepts previously thought infeasible with a laser driver. These benefits will lower the COE and make IFE plants more competitive at smaller size. Their use also raises unique issues that will impact the design and development of power plant subsystems. Cone targets have a significant mass of high Z material whether or not they have a hohlraum and they are not spherically symmetric. This has implications for target injection, tracking and chamber background gas allowable

High volume fabrication of laser targets using MEMS techniques

International Nuclear Information System (INIS)

Spindloe, C; Tomlinson, S; Green, J; Booth, N.; Tolley, M K; Arthur, G; Hall, F; Potter, R; Kar, S; Higginbotham, A

2016-01-01

The latest techniques for the fabrication of high power laser targets, using processes developed for the manufacture of Micro-Electro-Mechanical System (MEMS) devices are discussed. These laser targets are designed to meet the needs of the increased shot numbers that are available in the latest design of laser facilities. Traditionally laser targets have been fabricated using conventional machining or coarse etching processes and have been produced in quantities of 10s to low 100s. Such targets can be used for high complexity experiments such as Inertial Fusion Energy (IFE) studies and can have many complex components that need assembling and characterisation with high precision. Using the techniques that are common to MEMS devices and integrating these with an existing target fabrication capability we are able to manufacture and deliver targets to these systems. It also enables us to manufacture novel targets that have not been possible using other techniques. In addition, developments in the positioning systems that are required to deliver these targets to the laser focus are also required and a system to deliver the target to a focus of an F2 beam at 0.1Hz is discussed. (paper)

Robustness of Electrical Systems of Nuclear Power Plants in Light of the Fukushima Daiichi Accident (ROBELSYS). Workshop Proceedings, Paris, France, 1-4 April 2014 - Robustness of Electrical Systems of NPP's in Light of the Fukushima Daiichi Accident. ROBELSYS Workshop Proceedings

International Nuclear Information System (INIS)

2015-01-01

The March 2011 accident at Fukushima Daiichi triggered discussions about the significance of electrical power hazards and their treatment in safety analyses. In order to address these issues and provide relevant conclusions and recommendations to CSNI and CNRA, the Robustness in Electrical Systems (ROBELSYS) Technical Working Group was established in 2012 under the leadership of the Institut de Radioprotection et de Surete Nucleaire (IRSN) of France. The purpose of the ROBELSYS Technical Working Group was to organize an international workshop to identify and discuss the lessons learned from the Fukushima Daiichi accident. The workshop was focused on the provisions taken by various countries concerning national requirements and modifications to the plant designs in order to enhance the robustness of electrical systems, especially the protection against extreme external hazards. The ROBELSYS workshop was held at the OECD Conference Centre in Paris in April 1-4, 2014. A total of 105 participants attended the workshop representing industry and government organisations from 25 countries, as well as international organisations. A total of 34 technical presentations were given in seven sessions as follows: - 1: National Programmes on Evolution of Onsite and Offsite Electric Power Systems; - 2: Role of Electric Power in Severe Accident Management; - 3: Requirements for Robustness of Onsite Electric Power Systems; - 4: Simulation of Transients within NPP Plant Distribution Systems; - 5: Requirements for Equipment Used for Emergency Response; - 6: Margin Assessments for Modern Power Electronics; - 7: Digital Components in Power Systems. Items addressed in the workshop included: - Review of the lessons learned from the Fukushima accident concerning the robustness of electrical systems; - Review of the provisions already taken or planned after the Fukushima accident, regarding the sources, the distribution systems and the loads, and documenting the technical basis for these

Sensors and Controls Workshop Summary Report; TOPICAL

International Nuclear Information System (INIS)

Susan Maley; Robert R. Romanosky

2001-01-01

Higher operating efficiencies, emission reductions, improved reliability, and lower operating costs are benefits that the power industry can realize with the utilization of sensors and controls. However, for the power industry to derive the maximum benefit from sensors and controls, improvements in existing technologies and novel approaches to challenging measurements are needed. Recognizing the importance of sensors and controls, the U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) sponsored a sensors and controls workshop on April 17 to 18, 2001, in Washington, DC. The workshop focused on identifying technology needs in sensors and controls for existing fossil-energy power plants as well as future facilities conceived under the Vision 21 Program. Forty-six experts from 29 organizations, including private industry, research laboratories, academia, and government agencies, attended the workshop. The meeting opened with keynote speakers from NETL and the private sector. NETL officials spoke of the Vision 21 and advanced research programs. Speakers from the Electric Power Research Institute (EPRI) and Delphi Automotive Systems Research Laboratory discussed the improvements realized with their respective operation through the use of sensors and controls. NETL keynote speakers Robert Romanosky and Carl Bauer emphasized that developing sensor and control systems plays a critical role in DOE Office of Fossil Energy Vision 21 Program, clean coal activities under the Power Plant Improvement Initiative, and the proposed Clean Coal Power Initiative. The Vision 21 Program is aimed at providing technologies for ultra-clean fossil-fuel-based energy production with 60- to 75-percent efficiencies and near zero emissions. The program also uses a modular approach to present opportunities to not only generate power, but also co-produce clean fuels, chemicals, steam, and other useful products. The ultra-high efficiency and environmental performance goals

High-power spallation target using a heavy liquid metal free surface flow

International Nuclear Information System (INIS)

Litfin, K.; Fetzer, J.R.; Batta, A.; Class, A.G.; Wetzel, Th.

2015-01-01

A prototype of a heavy liquid metal free surface target as proposed for the multi-purpose hybrid research reactor for high-tech applications in Mol, Belgium, has been set up and experimentally investigated at the Karlsruhe Liquid Metal Laboratory. A stable operation was demonstrated in a wide range of operating conditions and the surface shape was detected and compared with numerical pre-calculations employing Star-CD. Results show a very good agreement of experiment and numerical predictions which is an essential input for other windowless target designs like the META:LIC target for the European Spallation Source. (author)

WORKSHOP: Radiofrequency superconductivity

International Nuclear Information System (INIS)

Tückmantel, Joachim

1993-01-01

several years. New ideas, such as 'high pressure (water) rinsing' and 'high pulsed power processing', attack on two different fronts - avoiding the creation of field emitters and removing existing ones. While first results are encouraging, the enemy is still very active! Although still futuristic, the application of high critical temperature superconductors was also on the agenda. Afternoon poster sessions highlighted detailed work, too specialized for the morning talks, allowing direct discussion. Two workshop days were given over to two special topics. One was high beam current applications (Bfactories, spallation sources), where cavities operate at relatively modest fields but couplers will have to work above today's power levels. The second was the TeV linear collider project with exclusively superconducting cavities (TESLA) asking for 25 MV/m at 1.3 GHz with high resonance quality factor (Q) but low production cost. A world collaboration of several laboratories (including CERN) is building a test facility at DESY to study industry-made cavities. This building is nearly complete. The next stage will be construction and testing of 8-cavity modules in a prototype accelerator section with beam. TESLA-type cavities are being built and tested in several laboratories. Greg Loew gave a status report on normal conducting competitors, such as NLC (Stanford - SLAC) and CLIC (CERN). The next workshop will be held in 1995 at Saclay, under the chairmanship of Bernard Aune

The Assessment and Management of Suicide Risk: State of Workshop Education

OpenAIRE

Pisani, Anthony R.; Cross, Wendi F.; Gould, Madelyn S.

2011-01-01

A systematic search of popular and scholarly databases identified workshops that addressed general clinical competence in the assessment or management of suicide risk, targeted mental health professionals, and had at least one peerreviewed publication. We surveyed workshop developers and examined empirical articles associated with each workshop. The state of workshop education is characterized by presenting the learning objectives, educational formats, instructor factors, and evaluation studi...

The Assessment and Management of Suicide Risk: State of Workshop Education

Science.gov (United States)

Pisani, Anthony R.; Cross, Wendi F.; Gould, Madelyn S.

2011-01-01

A systematic search of popular and scholarly databases identified workshops that addressed general clinical competence in the assessment or management of suicide risk, targeted mental health professionals, and had at least one peer-reviewed publication. We surveyed workshop developers and examined empirical articles associated with each workshop.…

Baltic Nuclear workshop. Final report

International Nuclear Information System (INIS)

Wahlberg, L.G.

2001-05-01

Proceedings of the NKS/BOK-1.6 workshop on crisis communication 'Baltic Nuclear', held in Stockholm March 19 -20, 2001, with participants from the nuclear power plants and nuclear authorities in the Baltic Sea region. The main content of the workshop was founded on the principle of 'learning by doing'. The participants were therefore practically trained in how to handle a crisis from an information and communication point of view. Added to that there were three different lectures. (au)

Proceedings of the 2016 Workshop on the Physics and Applications of High Brightness Beams

Science.gov (United States)

Cianchi, Alessandro; Ferrario, Massimo; Musumeci, Pietro; Rosenzweig, James

2017-09-01

We are proud to present the proceedings of the latest in the series of International Committee on Future Accelerators (ICFA)-endorsed workshops on the Physics and Applications of High Brightness Beams, which has been held at the Hotel Nacional in Havana, Cuba between March 28 and April 1, 2016. In total, 135 participants coming from 14 different countries attended this historic conference. In recognition of its pioneering role in the significant blossoming of relations between Cuba and the larger scientific community, this workshop also received the endorsement of UNESCO. The workshop organization was headed by co-chairs Massimo Ferrario (INFN-LNF) and James Rosenzweig (UCLA), with the essential and energetic contributions of local organizing committee chair Fidel Antonio Castro Smirnov (InSTEC, Havana). The workshop scientific agenda was developed under the care of program committee co-chairs Pietro Musumeci (UCLA) and Luca Serafini (INFN-Milano). The publication of the proceedings we present here was led by Alessandro Cianchi (Tor Vergata). Tangible contributions to the workshop infrastructure were received from UCLA, INFN-LNF, InSTEC, EuroNNAC2, and the US National Science Foundation. The workshop web site, which contains detailed information on the scientific agenda of the meeting, is found at https://conferences.pa.ucla.edu/hbb/.

Nuclear based diagnostics in high-power laser applications

Energy Technology Data Exchange (ETDEWEB)

Guenther, Marc; Sonnabend, Kerstin; Harres, Knut; Otten, Anke; Roth, Markus [TU Darmstadt, Institut fuer Kernphysik, Darmstadt (Germany); Vogt, Karsten; Bagnoud, Vincent [GSI Helmholtzzentrum fuer Schwerionenforschung, Darmstadt (Germany)

2010-07-01

High-power lasers allow focused intensities of >10{sup 18} W/cm{sup 2}. During the laser-solid interaction, an intense relativistic electron current is injected from the plasma into the target. One challenge is to characterize the electron dynamic close to the interaction region. Moreover, next generation high-power laser proton acceleration leads to high proton fluxes, which require novel, nuclear diagnostic techniques. We present an activation-based nuclear pyrometry for the investigation of electrons generated in relativistic laser-solid interactions. We use novel activation targets consisting of several isotopes with different photo-neutron disintegration thresholds. The electrons are decelerated inside the target via bremsstrahlung processes. The high-energy bremsstrahlung induces photo-nuclear reactions. In this energy range no disturbing low energy effects are important. Via the pyrometry the Reconstruction of the absolute yield, spectral and spatial distribution of the electrons is possible. For the characterization of proton beams we present a nuclear activation imaging spectroscopy (NAIS). The diagnostic is based on proton-neutron disintegration reactions of copper stacked in consecutive layers. An autoradiography of copper layers leads to spectrally and spatially reconstruction of the beam profile.

Cleanroom Energy Efficiency Workshop Proceedings

Energy Technology Data Exchange (ETDEWEB)

Tschudi, Bill

1999-03-15

On March 15, 1999, Lawrence Berkeley National Laboratory hosted a workshop focused on energy efficiency in Cleanroom facilities. The workshop was held as part of a multiyear effort sponsored by the California Institute for Energy Efficiency, and the California Energy Commission. It is part of a project that concentrates on improving energy efficiency in Laboratory type facilities including cleanrooms. The project targets the broad market of laboratory and cleanroom facilities, and thus cross-cuts many different industries and institutions. This workshop was intended to raise awareness by sharing case study success stories, providing a forum for industry networking on energy issues, contributing LBNL expertise in research to date, determining barriers to implementation and possible solutions, and soliciting input for further research.

Workshop on Developing Safe Software

International Nuclear Information System (INIS)

Lawrence, J.D.

1994-11-01

The Workshop on Developing Safe Software was held July 22--23, 1992, at the Hotel del Coronado, San Diego, California. The purpose of the workshop was to have four world experts discuss among themselves software safety issues which are of interest to the US Nuclear Regulatory Commission. These issues concern the development of software systems for use in nuclear power plant protection systems. The workshop comprised four sessions. Wednesday morning, July 22, consisted of presentations from each of the four panel members. On Wednesday afternoon, the panel members went through a list of possible software development techniques and commented on them. The Thursday morning, July 23, session consisted of an extended discussion among the panel members and the observers from the NRC. A final session on Thursday afternoon consisted of a discussion among the NRC observers as to what was learned from the workshop

Workshop on developing safe software

International Nuclear Information System (INIS)

Lawrence, J.D.

1992-01-01

The Workshop on Developing Safe Software was held July 22--23 at the Hotel del Coronado, San Diego, California. The purpose of the workshop was to have four world experts discuss among themselves software safety issues which are of interest to the U. S. Nuclear Regulatory Commission (NRC). These issues concern the development of software systems for use in nuclear power plant protection systems. The workshop comprised four sessions. Wednesday morning, July 22, consisted of presentations from each of the four panel members. On Wednesday afternoon, the panel members went through a list of possible software development techniques and commented on them. The Thursday morning, July 23, session consisted of an extended discussion among the panel members and the observers from the NRC. A final session on Thursday afternoon consisted of a discussion among the NRC observers as to what was teamed from the workshop

High power pulsed magnetron sputtering of transparent conducting oxides

International Nuclear Information System (INIS)

Sittinger, V.; Ruske, F.; Werner, W.; Jacobs, C.; Szyszka, B.; Christie, D.J.

2008-01-01

High power pulsed magnetron sputtering (HPPMS) has been used in order to study the deposition of transparent conducting oxides. We summarize the studies carried out on different materials (indium tin oxide-ITO and aluminium-doped zinc oxide-AZO) using rather different technological approaches, namely sputtering of ceramic targets and reactive sputtering. For the deposition of AZO reactive HPPMS for metallic targets has been used. A feedback control loop has been implemented in order to stabilize the discharge at any given setpoint on the hysteresis curve. The hysteresis was also found to have a rather untypical form. Reactive HPPMS was found to be a promising tool for obtaining high quality films of low total thickness. In the case of ITO deposition a ceramic target has been used. The process has been characterized in terms of its plasma emission and increasing indium ionization was found for higher peak power densities. The properties of the deposited films were compared to DC sputtered films. While for DC sputtering the choice of oxygen addition and shieldings is crucial for determining surface morphology and resistivity, in HPPMS sputtering peak power density has been found to be a good parameter for influencing the crystal structure. The morphologies obtained differ strongly from those seen in DC sputtering. At high power densities films with low surface roughness and excellent resistivity could be deposited without the use of shieldings

Autonomous target tracking of UAVs based on low-power neural network hardware

Science.gov (United States)

Yang, Wei; Jin, Zhanpeng; Thiem, Clare; Wysocki, Bryant; Shen, Dan; Chen, Genshe

2014-05-01

Detecting and identifying targets in unmanned aerial vehicle (UAV) images and videos have been challenging problems due to various types of image distortion. Moreover, the significantly high processing overhead of existing image/video processing techniques and the limited computing resources available on UAVs force most of the processing tasks to be performed by the ground control station (GCS) in an off-line manner. In order to achieve fast and autonomous target identification on UAVs, it is thus imperative to investigate novel processing paradigms that can fulfill the real-time processing requirements, while fitting the size, weight, and power (SWaP) constrained environment. In this paper, we present a new autonomous target identification approach on UAVs, leveraging the emerging neuromorphic hardware which is capable of massively parallel pattern recognition processing and demands only a limited level of power consumption. A proof-of-concept prototype was developed based on a micro-UAV platform (Parrot AR Drone) and the CogniMemTMneural network chip, for processing the video data acquired from a UAV camera on the y. The aim of this study was to demonstrate the feasibility and potential of incorporating emerging neuromorphic hardware into next-generation UAVs and their superior performance and power advantages towards the real-time, autonomous target tracking.

Narrow power deposition profiles on the JET divertor target

International Nuclear Information System (INIS)

Lingertat, J.; Laux, M.; Monk, R.

2001-01-01

One of the key unresolved issues in the design of a future fusion reactor is the power handling capability of the divertor target plates. Earlier we reported on the existence of narrow power deposition profiles in JET, obtained mainly from Langmuir probe measurements. We repeated these measurements in the MkI, MkII and MkIIGB divertor configurations with an upgraded probe system, which allowed us to study the profile shape in more detail. The main results of this study are: In NB heated discharges the electron temperature and power flux at the outer target show a distinct peak of ∼5 mm half-width near the separatrix strike point. The corresponding profiles on the inner target do not show a similar feature. The height of the narrow peak increases with NB heating power and decreases with deuterium and impurity gas puffing. Ion orbit losses are suggested as a possible explanation of the observed profile shape

Proceedings: EPRI Workshop 2 -- Technical basis for EPA HLW disposal criteria

International Nuclear Information System (INIS)

Rogers, V.

1993-03-01

The Electric Power Research Institute (EPRI) sponsored this workshop to address the scientific and technical issues underlying the regulatory criteria, or standard, for the disposal of spent nuclear fuel, high-level radioactive waste, and transuranic waste, commonly referred to collectively as high-level waste (HLW). These regulatory criteria were originally promulgated by the US Environmental Protection Agency (EPA) in 40 CFR Part 191 in 1985. However, significant portions of the regulation were remanded by the Ninth Circuit Court of Appeals in 1987. This is the second of two workshops. Topics discussed include: gas pathway; individual and groundwater protection; human intrusion; population protection; performance; TRU conversion factors and discussions. Individual projects re processed separately for the databases

Workshop on extremely high energy density plasmas and their diagnostics

Energy Technology Data Exchange (ETDEWEB)

Ishii, Shozo (ed.)

2001-09-01

Compiled are the papers presented at the workshop on 'Extremely High Energy Density Plasmas and Their Diagnostics' held at National Institute for Fusion Science. The papers cover physics and applications of extremely high-energy density plasmas such as dense z-pinch, plasma focus, and intense pulsed charged beams. Separate abstracts were presented for 7 of the papers in this report. The remaining 25 were considered outside the subject scope of INIS. (author)

Workshop on extremely high energy density plasmas and their diagnostics

International Nuclear Information System (INIS)

Ishii, Shozo

2001-09-01

Compiled are the papers presented at the workshop on 'Extremely High Energy Density Plasmas and Their Diagnostics' held at National Institute for Fusion Science. The papers cover physics and applications of extremely high-energy density plasmas such as dense z-pinch, plasma focus, and intense pulsed charged beams. Separate abstracts were presented for 7 of the papers in this report. The remaining 25 were considered outside the subject scope of INIS. (author)

Dense granular Flows: a conceptual design of high-power neutron source

Directory of Open Access Journals (Sweden)

Yang Lei

2017-01-01

Full Text Available A high-power neutron source system is very useful for multifunctional applications, such as material facilities for advanced nuclear power, space radiation studies, radiography and tomography. Here the idea of inclined dense granular flow is utilized and developed in a new conceptual design of a compact high-power target to produce a high-energy and high-flux neutron irradiation (the flux is up to 1015 n/cm2/s or even 1016. Comparing to the traditional solid and liquid heavy metal targets, this design has advantages in material choice, fluid stability, heat removal, etc. In this paper the natures of the granular flows in an inclined chute are investigated and preliminary experimental and numerical results are reported. Then the feasibility of this design is discussed.

Proceedings of the workshop on ion source issues relevant to a pulsed spallation neutron source: Part 1: Workshop summary

International Nuclear Information System (INIS)

Schroeder, L.; Leung, K.N.; Alonso, J.

1994-10-01

The workshop reviewed the ion-source requirements for high-power accelerator-driven spallation neutron facilities, and the performance of existing ion sources. Proposals for new facilities in the 1- to 5-MW range call for a widely differing set of ion-source requirements. For example, the source peak current requirements vary from 40 mA to 150 mA, while the duty factor ranges from 1% to 9%. Much of the workshop discussion centered on the state-of-the-art of negative hydrogen ion source (H - ) technology and the present experience with Penning and volume sources. In addition, other ion source technologies, for positive ions or CW applications were reviewed. Some of these sources have been operational at existing accelerator complexes and some are in the source-development stage on test stands

The fourth international energy agency international workshop on beryllium technology for fusion

International Nuclear Information System (INIS)

Scaffidi-Argentina, F.; Longhurst, G.R.

2000-01-01

The main objective of the workshop was to support the advancement of the international development of fusion power through communication and dissemination of information on progress made in beryllium technology. This has been accomplished through presentation of original research on issues of current interest to the fusion beryllium community. The workshop was divided into ten technical sessions that addressed the following general topics: production and characterization, health and safety, forming and joining, chemical compatibility, thermal-mechanical properties, pebble bed behavior, high-heat-flux performance, irradiation effects, plasma-tritium interaction, and molten beryllium-bearing salts

The fourth international energy agency international workshop on beryllium technology for fusion

Energy Technology Data Exchange (ETDEWEB)

Scaffidi-Argentina, F.; Longhurst, G.R.

2000-05-01

The main objective of the workshop was to support the advancement of the international development of fusion power through communication and dissemination of information on progress made in beryllium technology. This has been accomplished through presentation of original research on issues of current interest to the fusion beryllium community. The workshop was divided into ten technical sessions that addressed the following general topics: production and characterization, health and safety, forming and joining, chemical compatibility, thermal-mechanical properties, pebble bed behavior, high-heat-flux performance, irradiation effects, plasma-tritium interaction, and molten beryllium-bearing salts.

Workshops for state review of site suitability criteria for high-level radioactive waste repositories. Discussion Group reports

International Nuclear Information System (INIS)

1977-10-01

The NRC Waste Management Program and the Office of State Programs held three regional workshops to solicit ideas from State executives and legislators on the siting and licensing procedures for high level waste repositories and to solicit comments on the NRC preliminary site suitability criteria. The workshops were held in Denver, Colorado; New Orleans, Louisiana; and Philadelphia, Pennsylvania during the period 19-30 September 1977. The reports from these workshops are contained herein. The workshops were attended by 170 invited State executives and legislators from 46 states. In addition, there were over 80 observers from diverse backgrounds including the general public, government, industry, professional consultants and university faculty. The workshops were announced in the Federal Register on September 1, 1977

Accelerator reliability workshop

International Nuclear Information System (INIS)

Hardy, L.; Duru, Ph.; Koch, J.M.; Revol, J.L.; Van Vaerenbergh, P.; Volpe, A.M.; Clugnet, K.; Dely, A.; Goodhew, D.

2002-01-01

About 80 experts attended this workshop, which brought together all accelerator communities: accelerator driven systems, X-ray sources, medical and industrial accelerators, spallation sources projects (American and European), nuclear physics, etc. With newly proposed accelerator applications such as nuclear waste transmutation, replacement of nuclear power plants and others. Reliability has now become a number one priority for accelerator designers. Every part of an accelerator facility from cryogenic systems to data storage via RF systems are concerned by reliability. This aspect is now taken into account in the design/budget phase, especially for projects whose goal is to reach no more than 10 interruptions per year. This document gathers the slides but not the proceedings of the workshop

Accelerator reliability workshop

Energy Technology Data Exchange (ETDEWEB)

Hardy, L; Duru, Ph; Koch, J M; Revol, J L; Van Vaerenbergh, P; Volpe, A M; Clugnet, K; Dely, A; Goodhew, D

2002-07-01

About 80 experts attended this workshop, which brought together all accelerator communities: accelerator driven systems, X-ray sources, medical and industrial accelerators, spallation sources projects (American and European), nuclear physics, etc. With newly proposed accelerator applications such as nuclear waste transmutation, replacement of nuclear power plants and others. Reliability has now become a number one priority for accelerator designers. Every part of an accelerator facility from cryogenic systems to data storage via RF systems are concerned by reliability. This aspect is now taken into account in the design/budget phase, especially for projects whose goal is to reach no more than 10 interruptions per year. This document gathers the slides but not the proceedings of the workshop.

Physics Analysis Tools Workshop 2007

CERN Multimedia

Elizabeth Gallas,

The ATLAS PAT (Physics Analysis Tools) group evaluates, develops and tests software tools for the analysis of physics data, consistent with the ATLAS analysis and event data models. Following on from earlier PAT workshops in London (2004), Tucson (2005) and Tokyo (2006), this year's workshop was hosted by the University of Bergen in Norway on April 23-28 with more than 60 participants. The workshop brought together PAT developers and users to discuss the available tools with an emphasis on preparing for data taking. At the start of the week, workshop participants, laptops and power converters in-hand, jumped headfirst into tutorials, learning how to become trigger-aware and how to use grid computing resources via the distributed analysis tools Panda and Ganga. The well organised tutorials were well attended and soon the network was humming, providing rapid results to the users and ample feedback to the developers. A mid-week break was provided by a relaxing and enjoyable cruise through the majestic Norwegia...

Very low pressure high power impulse triggered magnetron sputtering

Science.gov (United States)

Anders, Andre; Andersson, Joakim

2013-10-29

A method and apparatus are described for very low pressure high powered magnetron sputtering of a coating onto a substrate. By the method of this invention, both substrate and coating target material are placed into an evacuable chamber, and the chamber pumped to vacuum. Thereafter a series of high impulse voltage pulses are applied to the target. Nearly simultaneously with each pulse, in one embodiment, a small cathodic arc source of the same material as the target is pulsed, triggering a plasma plume proximate to the surface of the target to thereby initiate the magnetron sputtering process. In another embodiment the plasma plume is generated using a pulsed laser aimed to strike an ablation target material positioned near the magnetron target surface.

Electrostatic levitation, control and transport in high rate, low cost production of inertial confinement fusion targets

International Nuclear Information System (INIS)

Hendricks, C.D.; Johnson, W.L.

1979-01-01

Inertial confinement fusion requires production of power plant grade targets at high rates and process yield. A review of present project specifications and techniques to produce targets is discussed with special emphasis on automating the processes and combining them with an electrostatic transport and suspension system through the power plant target factory

Placental Origins of Adverse Pregnancy Outcomes: Potential Molecular Targets- An Executive Workshop Summary of the Eunice Kennedy Shriver National Institute of Child Health and Human Development

Science.gov (United States)

Ilekis, John V.; Tsilou, Ekaterini; Fisher, Susan; Abrahams, Vikki M.; Soares, Michael J.; Cross, James C.; Zamudio, Stacy; Illsley, Nicholas P.; Myatt, Leslie; Colvis, Christine; Costantine, Maged M.; Haas, David M.; Sadovsky, Yoel; Weiner, Carl; Rytting, Erik; Bidwell, Gene

2016-01-01

Although much progress is being made in understanding the molecular pathways in the placenta involved in the pathophysiology of pregnancy related disorders, a significant gap exists in utilizing this information for developing new drug therapies to improve pregnancy outcome. On March 5–6, 2015, the Eunice Kennedy Shriver National Institute of Child Health and Human Development of the National Institutes of Health sponsored a two day workshop titled Placental Origins of Adverse Pregnancy Outcomes: Potential Molecular Targets to begin to address this gap. Particular emphasis was given in the identification of important molecular pathways that could serve as drug targets and the advantages and disadvantages of targeting these particular pathways. This article is a summary of the proceedings of this workshop. A broad number of topics were covered ranging from basic placental biology to clinical trials. This included research in the basic biology of placentation, such as trophoblast migration and spiral artery remodeling, and trophoblast sensing and response to infectious and non-infectious agents. Research findings in these areas will be critical for formulating developing future treatments and developing therapies for the prevention of a number of pregnancy disorders of placental origin including preeclampsia, fetal growth restriction, and uterine inflammation. Research was also presented summarizing ongoing clinical efforts in the U.S. and in Europe testing novel interventions for preeclampsia and fetal growth restriction, including agents such as oral arginine supplementation, sildenafil, pravastatin, gene therapy using virally-delivered vascular endothelial growth factor, and oxygen supplementation therapy. Strategies were also proposed to improve fetal growth by enhancing nutrient transport to the fetus by modulating their placental transporters, as well as targeting placental mitochondrial dysfunction and oxidative stress to improve placental health. The roles

Proceedings of the flexible, midsize gas turbine program planning workshop

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The US Department of Energy (DOE) and the California Energy Commission (CEC) held a program planning workshop on March 4--5, 1997 in Sacramento, California on the subject of a flexible, midsize gas turbine (FMGT). The workshop was also co-sponsored by the Electric Power Research Institute (EPRI), the Gas Research Institute (GRI), the Gas Turbine Association (GTA), and the Collaborative Advanced Gas Turbine Program (CAGT). The purpose of the workshop was to bring together a broad cross section of knowledgeable people to discuss the potential benefits, markets, technical attributes, development costs, and development funding approaches associated with making this new technology available in the commercial marketplace. The participants in the workshop included representatives from the sponsoring organizations, electric utilities, gas utilities, independent power producers, gas turbine manufacturers, gas turbine packagers, and consultants knowledgeable in the power generation field. Thirteen presentations were given on the technical and commercial aspects of the subject, followed by informal breakout sessions that dealt with sets of questions on markets, technology requirements, funding sources and cost sharing, and links to other programs.

Summary of the CERN Workshop on Materials for Collimators and Beam Absorbers

CERN Document Server

Schmidt, R; Bertarelli, A; Ferrari, A; Weterings, W; Mokhov, N V

2008-01-01

The main focus of the workshop was on collimators and beam absorbers for (mainly) High Energy Hadron Accelerators, with the energy stored in the beams far above damage limit. The objective was to better understand the technological limits imposed by mechanisms related to beam impact on materials. The idea to organise this workshop came up during the High Intensity High Brightness Hadron Beams, ICFA-HB2006 in Japan [1]. The workshop was organised 3-5 September 2007 at CERN, with about 60 participants, including 20 from outside CERN. About 30 presentations were given [2]. The event was driven by the LHC challenge, with more than 360 MJoule stored in each proton beam. The entire beam or its fraction will interact with LHC collimators and beam absorbers, and with the LHC beam dump blocks. Collimators and beam absorbers are also of the interest for other labs and accelerators: - CERN: for the CNGS target, for SPS beam absorbers (extraction protection) and collimators for protecting the transfer line between SPS an...

ISAC target operation with high proton currents

CERN Document Server

Dombsky, M; Schmor, P; Lane, M

2003-01-01

The TRIUMF-ISAC facility target stations were designed for ISOL target irradiations with up to 100 mu A proton beam currents. Since beginning operation in 1998, ISAC irradiation currents have progressively increased from initial values of approx 1 mu A to present levels of up to 40 mu A on refractory metal foil targets. In addition, refractory carbide targets have operated at currents of up to 15 mu A for extended periods. The 1-40 mu A operational regime is achieved by tailoring each target to the thermal requirements dictated by material properties such as beam power deposition, thermal conductivity and maximum operating temperature of the target material. The number of heat shields on each target can be varied in order to match the effective emissivity of the target surface for the required radiative power dissipation. Targets of different thickness, surface area and volume have been investigated to study the effect of diffusion and effusion delays on the yield of radioisotopes. For yields of short-lived p...

Optical Network Testbeds Workshop

Energy Technology Data Exchange (ETDEWEB)

Joe Mambretti

2007-06-01

This is the summary report of the third annual Optical Networking Testbed Workshop (ONT3), which brought together leading members of the international advanced research community to address major challenges in creating next generation communication services and technologies. Networking research and development (R&D) communities throughout the world continue to discover new methods and technologies that are enabling breakthroughs in advanced communications. These discoveries are keystones for building the foundation of the future economy, which requires the sophisticated management of extremely large qualities of digital information through high performance communications. This innovation is made possible by basic research and experiments within laboratories and on specialized testbeds. Initial network research and development initiatives are driven by diverse motives, including attempts to solve existing complex problems, the desire to create powerful new technologies that do not exist using traditional methods, and the need to create tools to address specific challenges, including those mandated by large scale science or government agency mission agendas. Many new discoveries related to communications technologies transition to wide-spread deployment through standards organizations and commercialization. These transition paths allow for new communications capabilities that drive many sectors of the digital economy. In the last few years, networking R&D has increasingly focused on advancing multiple new capabilities enabled by next generation optical networking. Both US Federal networking R&D and other national R&D initiatives, such as those organized by the National Institute of Information and Communications Technology (NICT) of Japan are creating optical networking technologies that allow for new, powerful communication services. Among the most promising services are those based on new types of multi-service or hybrid networks, which use new optical networking

NNSA / IAEA VVER reactor safety workshops. May 2002 - April 2003. Executive summary

International Nuclear Information System (INIS)

Evans, M.; Petri, M. C.

2003-01-01

Over the past year, the U.S. National Nuclear Security Administration (NNSA) has sponsored four workshops to compare the probabilistic risk assessments (PRAs) of Soviet-designed VVER power plants. The ''International Workshop on Safety of First-Generation VVER-440 Nuclear Power Plants'' was held on May 20-25, 2002, in Piestany, Slovakia. A short follow-on workshop was held in Bratislava, Slovakia, on November 5-6, 2002, to complete the work begun in May. Piestany was the location also for the ''International Workshop on Safety of Second-Generation VVER-440 Nuclear Power Plants'' (September 9-14, 2002) and the ''International Workshop on Safety of VVER-1000 Nuclear Power Plants'' (April 7-12, 2003). The four workshops were held in cooperation with the International Atomic Energy Agency (IAEA), the Nuclear Regulatory Authority of Slovakia (UJD), the Center for Nuclear Safety in Central and Eastern Europe (CENS), and Argonne National Laboratory (ANL). The objectives of the workshops were to identify the impact of the improvements on the core damage frequency; the contribution to the PRA results of different assumptions about events that can occur at the plants; and to understand, identify, and prioritize potential improvements in hardware and plant operation of VVER nuclear power plants. These objectives were achieved based on insights gained from recent PRAs completed by the plants and their technical support organizations. Nine first-generation VVER-440 plants (nominally of the VVER-440/230 design) are currently operating in Armenia, Bulgaria, Russia, and Slovakia. Sixteen VVER-440/213 plants are currently operating in the Czech Republic, Hungary, Russia, Slovakia, and Ukraine. Twenty-three VVER-1000 plants are currently operating in Bulgaria, the Czech Republic, Russia, and Ukraine. Eleven addition plants are in the advanced stages of construction in various parts of the world. The workshops reviewed the current configuration and safety status of each plant

Cooling System for the Merit High-Power Target Experiment

CERN Document Server

Haug, F; Silva, P; Pezzeti, M; Pavlov, O; Pirotte, O; Metselaar, J; Efthymiopoulos, I; Fabich, A; Lettry, J; Kirk, H G; McDonald, K T; Titus, P; Bennett, J R J

2010-01-01

MERIT is a proof-of-principle experiment of a target station suitable as source for future muon colliders or neutrino factories. When installed at the CERN (European Organization for Nuclear Research) PS (Proton Synchrotron)complex fast-extracted high-intensity proton beams intercepted a free mercury jet inside a normal-conducting, pulsed 15-T capture solenoid magnet cooled with liquid nitrogen. Up to 25 MJ of Joule heat was dissipated in the magnet during a pulse. The fully automated, remotely controlled cryogenic system of novel design permitted the transfer of nitrogen by the sole means of differential pressures inside the vessels. This fast cycling system permitted several hundred tests in less than three weeks during the 2007 data taking campaign.

Workshop on the role of natural analogs in geologic disposal of high-level nuclear waste

International Nuclear Information System (INIS)

Murphy, W.M.; Kovach, L.A.

1995-01-01

A workshop on the Role of Natural Analogs in Geologic Disposal of High-Level Nuclear Waste (HLW) was held in San Antonio, Texas, on July 22-25, 1991. It was sponsored by the US Nuclear Regulatory Commission (NRC) and the Center for Nuclear Waste Regulatory Analyses (CNWRA). Invitations to the workshop were extended to a large number of individuals with a variety of technical and professional interests related to geologic disposal of nuclear waste and natural analog studies. The objective of the workshop was to examine the role of natural analog studies in performance assessment, site characterization, and prioritization of research related to geologic disposal of HLW

Direct drive target survival during injection in an inertial fusion energy power plant

International Nuclear Information System (INIS)

Petzoldt, R.W.; Goodin, D.T.; Nikroo, A.; Stephens, E.; Alexander, N.B.; Gallix, R.; Siegel, N.; Raffray, A.R.; Mau, T.K.; Tillack, M.; Najmabadi, F.; Krasheninnikov, S.I.

2002-01-01

In inertial fusion energy (IFE) power plant designs, the fuel is a spherical layer of frozen DT contained in a target that is injected at high velocity into the reaction chamber. For direct drive, typically laser beams converge at the centre of the chamber (CC) to compress and heat the target to fusion conditions. To obtain the maximum energy yield from the fusion reaction, the frozen DT layer must be at about 18.5 K and the target must maintain a high degree of spherical symmetry and surface smoothness when it reaches the CC. During its transit in the chamber the cryogenic target is heated by radiation from the hot chamber wall. The target is also heated by convection as it passes through the rarefied fill-gas used to control chamber wall damage by x-rays and debris from the target explosion. This article addresses the temperature limits at the target surface beyond which target uniformity may be damaged. It concentrates on direct drive targets because fuel warm up during injection is not currently thought to be an issue for present indirect drive designs and chamber concepts. Detailed results of parametric radiative and convective heating calculations are presented for direct-drive targets during injection into a dry-wall reaction chamber. The baseline approach to target survival utilizes highly reflective targets along with a substantially lower chamber wall temperature and fill-gas pressure than previously assumed. Recently developed high-Z material coatings with high heat reflectivity are discussed and characterized. The article also presents alternate target protection methods that could be developed if targets with inherent survival features cannot be obtained within a reasonable time span. (author)

IAEA INTOR workshop report, group 8

International Nuclear Information System (INIS)

Tamura, Sanae; Shimada, Ryuichi; Miya, Naoyuki; Shinya, Kichiro; Kishimoto, Hiroshi

1979-10-01

This report provides material for discussion in Group 8, Power Supply and Transfer, of the IAEA Workshop on INTOR. A new system for the poloidal field power supply for INTOR is proposed and its overall system design is described. The results of simulation calculation of the system are also given. (author)

Results of the Workshop on Two-Phase Flow, Fluid Stability and Dynamics: Issues in Power, Propulsion, and Advanced Life Support Systems

Science.gov (United States)

McQuillen, John; Rame, Enrique; Kassemi, Mohammad; Singh, Bhim; Motil, Brian

2003-01-01

The Two-phase Flow, Fluid Stability and Dynamics Workshop was held on May 15, 2003 in Cleveland, Ohio to define a coherent scientific research plan and roadmap that addresses the multiphase fluid problems associated with NASA s technology development program. The workshop participants, from academia, industry and government, prioritized various multiphase issues and generated a research plan and roadmap to resolve them. This report presents a prioritization of the various multiphase flow and fluid stability phenomena related primarily to power, propulsion, fluid and thermal management and advanced life support; and a plan to address these issues in a logical and timely fashion using analysis, ground-based and space-flight experiments.

Using Sound to Modify Fish Behavior at Power-Production and Water-Control Facilities: A Workshop December 12-13, 1995. Phase II: Final Report.

Energy Technology Data Exchange (ETDEWEB)

Carlson, Thomas J. [ed.] [Pacific Northwest National Lab., Richland, WA (United States); Popper, Arthur N. [ed.] [Univ. of Maryland, College Park, MD (United States)

1997-06-01

A workshop on ``Use of Sound for Fish Protection at Power-Production and Water-Control Facilities`` was held in Portland, Oregon on December 12--13, 1995. This workshop convened a 22-member panel of international experts from universities, industry, and government to share knowledge, questions, and ideas about using sound for fish guidance. Discussions involved in a broad range of indigenous migratory and resident fish species and fish-protection issues in river systems, with particular focus on the Columbia River Basin. Because the use of sound behavioral barriers for fish is very much in its infancy, the workshop was designed to address the many questions being asked by fishery managers and researchers about the feasibility and potential benefits of using sound to augment physical barriers for fish protection in the Columbia River system.

20040217 NATO Advanced Research Workshop on Quasi-Optical Control of Intense Microwave Transmission Nizhny Novgorod, Russia 17 - 20 Feb 2004 2004 novgorod20040217 20040220

CERN Document Server

Hirshfield, Jay L

2005-01-01

This volume assembles the texts of presentations given at the NATO-sponsored Advanced Research Workshop on Quasi-Optical Transmission of High-Power Microwaves, held in Nizhny Novgorod, Russia in February 2004. The presentations bridge a wide range of technical areas, but share common tools of analysis and design. Applications of quasi-optics extend to the use of high-power microwaves—including millimeter-waves— for radar and communications (especially deep space millimeter-wave systems, space debris detection radar, and radar for the detection of small targets moving over heavy clutter); particle accelerators (especially for a future high-acceleration-gradient electron-positron collider); plasma research (especially for controlled nuclear fusion and waste decontamination); and material processing (in particular, ceramic sintering with millimeter-waves, and the coating of metal surfaces with protective dielectric films.). Scientists and engineers working in any of these areas should benefit significantly f...

78 FR 72673 - Zero Rate Reactive Power Rate Schedules; Notice of Staff Workshop

Science.gov (United States)

2013-12-03

... Regulatory Commission, 888 First Street NE., Washington, DC 20426. The workshop will be led by Commission... persons to listen to the workshop, but not participate. Anyone with Internet access who wants to listen...

Nuclear physics workshop

International Nuclear Information System (INIS)

1988-01-01

This Workshop in Nuclear Physics related to the TANDAR, took place in Buenos Aires in April from 23 to 26, 1987, with attendance of foreign scientists. There were presented four seminars and a lot of studies which deal with the following fields: Nuclear Physics at medium energies, Nuclear Structure, Nuclear Reactions, Nuclear Matter, Instrumentation and Methodology for Nuclear Spectroscopy, Classical Physics, Quantum Mechanics and Field Theory. It must be emphasized that the Electrostatic Accelerator TANDAR allows to work with heavy ions of high energy, that opens a new field of work in PIXE (particle induced X-ray emission). This powerful analytic technique makes it possiblethe analysis of nearly all the elements of the periodic table with the same accuracy. (M.E.L.) [es

A Project-Based Engineering and Leadership Workshop for High School Students

Science.gov (United States)

Ryder, Linda Sue; Pegg, Jerine; Wood, Nathan

2012-01-01

Summer outreach programs provide pre-college participants an introduction to college life and exposure to engineering in an effort to raise the level of interest and bring more students into engineering fields. The Junior Engineering, Mathematics, and Science (JEMS) program is a project-based summer workshop in which teams of high school students…

Proceedings from the technical workshop on near-field performance assessment for high-level waste

International Nuclear Information System (INIS)

Sellin, P.; Apted, M.; Gago, J.

1991-12-01

This report contains the proceedings of 'Technical workshop of near-filed performance assessment for high-level waste' held in Madrid October 15-17, 1990. It includes the invited presentations and summaries of the scientific discussions. The workshop covered several topics: * post-emplacement environment, * benchmarking of computer codes, * glass release, * spent-fuel release, * radionuclide solubility, * near-field transport processes, * coupled processes in the near-field, * integrated assessments, * sensitivity analyses and validation. There was an invited presentation on each topic followed by an extensive discussion. One of the points highlighted in the closing discussion of the workshop was the need for international cooperation in the field of near-field performance assessment. The general opinion was that this was best achieved in smaller groups discussing specific questions. (au) Separate abstracts were prepared for 9 papers in this volume

Summary of cosmology workshop

Indian Academy of Sciences (India)

in quality, quantity, and the scope of cosmological observations. While the ob- ... In this article, I summarize both the oral and poster presentations made at the workshop. ... the angular spectrum of CMB anisotropy with recent measurements of the power spectrum of ..... A thermodynamical treatment within the framework of.

Auroral Tomography Workshop, Proceedings

International Nuclear Information System (INIS)

Steen, Aa.

1993-08-01

In ionospheric and atmospheric physics the importance of multi-station imaging has grown as a consequence of the availability of scientific grade CCD cameras with digital output and affordable massive computing power. Tomographic inversion techniques are used in many different areas, e.g. medicine, plasma research and space physics. The tomography workshop was announced to gather a limited group of people interested in auroral tomography or tomographic inversion methods in general. ALIS (Auroral Large Imaging System) is a multi-station ground-based system developed primarily for three-dimensional auroral imaging, however other non-auroral objects can be studied with ALIS, e.g. stratospheric clouds. Several of the contributions in the workshop dealt with problems related to geometries similar to the ALIS-configuration. The Proceedings contain written contributions received either in abstract form or as full papers. The Proceedings also contain contributions intended for the Workshop but not presented due to the absence of the speaker. Separate abstracts have been prepared for 15 of the 17 papers

Proceedings of the CEATI 2010 distribution planning workshop

International Nuclear Information System (INIS)

2010-01-01

This workshop provided a forum for electrical industry distribution experts to discuss methods of distribution planning that will ensure the provision of low-cost and reliable electrical service to present and future customers. Participants in the workshop discussed methods of integrating renewable energy resources, maximizing the use of existing assets, and reducing the carbon footprint of electric utilities. The effects of new loads on reliability, power quality, and voltage stability were considered. Planning distribution system modifications for the future were reviewed. The workshop provided an overview of distribution planning in relation to smart grids. The workshop included sessions on distribution planning for the 21. century; planning for a smarter grid; integrating renewable energy into the distribution system; and planning to manage reliability. The workshop featured 22 presentations, of which 16 have been catalogued separately for inclusion in this database. tabs., figs.

Power utility generation portfolio optimization as function of specific RES and decarbonisation targets – EPBiH case study

International Nuclear Information System (INIS)

Kazagic, Anes; Merzic, Ajla; Redzic, Elma; Music, Mustafa

2014-01-01

Highlights: • Guidelines for power utilities to reach specific decarbonisation targets offered. • Optimization model of RES share to be introduced into power system is proposed. • Single criteria analysis and multicriteria sustainability assessment are applied. • The optimization method has been demonstrated on a real power system. • In the considered case, HIGH RES scenario showed to be the preferable one. - Abstract: This paper provides guidelines and principles for power utilities to reach specific energy and decarbonisation targets. Method of power generation portfolio optimization, as function of sustainability and decarbonisation, along with appropriate criteria, has been proposed. Application of this optimization method has been demonstrated on a real power system – power utility JP Elektroprivreda BiH d.d. – Sarajevo (EPBiH), a typical example of South East European power system. The software tool WASP IV has been employed in the analysis, in order to define the dynamics and an optimized expansion of generation portfolio of the power system under consideration for the next period. The mid-term generation portfolio development plan for the EPBiH power system until year 2030 has been made during this research, taking into account the shutdown dynamics of existing power units and commissioning new ones, in order to provide safe supply of electric and heat energy for local consumers. Three basic scenario of renewable energy sources (RES) expansion have been analysed to reach specific RES and decarbonisation targets set for 2030, including RES share increase from the current level of 18% up to 35% (LOW RES), 45% (MID RES) and 55% (HIGH RES). Effects to the sustainability are considered through environmental, economic and social indicators. Multicriteria sustainability assessment gave an advantage to the HIGH RES, under assumption of equal weighting factors of economic and environment groups of indicators. Also, single criteria analysis has been

Effect of graphite target power density on tribological properties of graphite-like carbon films

Science.gov (United States)

Dong, Dan; Jiang, Bailing; Li, Hongtao; Du, Yuzhou; Yang, Chao

2018-05-01

In order to improve the tribological performance, a series of graphite-like carbon (GLC) films with different graphite target power densities were prepared by magnetron sputtering. The valence bond and microstructure of films were characterized by AFM, TEM, XPS and Raman spectra. The variation of mechanical and tribological properties with graphite target power density was analyzed. The results showed that with the increase of graphite target power density, the deposition rate and the ratio of sp2 bond increased obviously. The hardness firstly increased and then decreased with the increase of graphite target power density, whilst the friction coefficient and the specific wear rate increased slightly after a decrease with the increasing graphite target power density. The friction coefficient and the specific wear rate were the lowest when the graphite target power density was 23.3 W/cm2.

High-flux neutron source based on a liquid-lithium target

Science.gov (United States)

Halfon, S.; Feinberg, G.; Paul, M.; Arenshtam, A.; Berkovits, D.; Kijel, D.; Nagler, A.; Eliyahu, I.; Silverman, I.

2013-04-01

A prototype compact Liquid Lithium Target (LiLiT), able to constitute an accelerator-based intense neutron source, was built. The neutron source is intended for nuclear astrophysical research, boron neutron capture therapy (BNCT) in hospitals and material studies for fusion reactors. The LiLiT setup is presently being commissioned at Soreq Nuclear research Center (SNRC). The lithium target will produce neutrons through the 7Li(p,n)7Be reaction and it will overcome the major problem of removing the thermal power generated by a high-intensity proton beam, necessary for intense neutron flux for the above applications. The liquid-lithium loop of LiLiT is designed to generate a stable lithium jet at high velocity on a concave supporting wall with free surface toward the incident proton beam (up to 10 kW). During off-line tests, liquid lithium was flown through the loop and generated a stable jet at velocity higher than 5 m/s on the concave supporting wall. The target is now under extensive test program using a high-power electron-gun. Up to 2 kW electron beam was applied on the lithium flow at velocity of 4 m/s without any flow instabilities or excessive evaporation. High-intensity proton beam irradiation will take place at SARAF (Soreq Applied Research Accelerator Facility) superconducting linear accelerator currently in commissioning at SNRC.

SPLASH'13 workshops summary

DEFF Research Database (Denmark)

Balzer, S.; Schultz, U. P.

2013-01-01

Following its long-standing tradition, SPLASH 2013 will host 19 high-quality workshops, allowing their participants to meet and discuss research questions with peers, to mature new and exciting ideas, and to build up communities and start new collaborations. SPLASH workshops complement the main t...

Towards short wavelengths FELs workshop

International Nuclear Information System (INIS)

Ben-Zvi, I.; Winick, H.

1993-01-01

This workshop was caged because of the growing perception in the FEL source community that recent advances have made it possible to extend FEL operation to wavelengths about two orders of magnitude shorter than the 240 nm that has been achieved to date. In addition short wavelength FELs offer the possibilities of extremely high peak power (several gigawatts) and very short pulses (of the order of 100 fs). Several groups in the USA are developing plans for such short wavelength FEL facilities. However, reviewers of these plans have pointed out that it would be highly desirable to first carry out proof-of-principle experiments at longer wavelengths to increase confidence that the shorter wavelength devices will indeed perform as calculated. The need for such experiments has now been broadly accepted by the FEL community. Such experiments were the main focus of this workshop as described in the following objectives distributed to attendees: (1) Define measurements needed to gain confidence that short wavelength FELs will perform as calculated. (2) List possible hardware that could be used to carry out these measurements in the near term. (3) Define a prioritized FEL physics experimental program and suggested timetable. (4) Form collaborative teams to carry out this program

Towards short wavelengths FELs workshop

Science.gov (United States)

Ben-Zvi, I.; Winick, H.

1993-11-01

This workshop was caged because of the growing perception in the FEL source community that recent advances have made it possible to extend FEL operation to wavelengths about two orders of magnitude shorter than the 240 nm that has been achieved to date. In addition short wavelength FEL's offer the possibilities of extremely high peak power (several gigawatts) and very short pulses (of the order of 100 fs). Several groups in the USA are developing plans for such short wavelength FEL facilities. However, reviewers of these plans have pointed out that it would be highly desirable to first carry out proof-of-principle experiments at longer wavelengths to increase confidence that the shorter wavelength devices will indeed perform as calculated. The need for such experiments has now been broadly accepted by the FEL community. Such experiments were the main focus of this workshop as described in the following objectives distributed to attendees: (1) Define measurements needed to gain confidence that short wavelength FEL's will perform as calculated. (2) List possible hardware that could be used to carry out these measurements in the near term. (3) Define a prioritized FEL physics experimental program and suggested timetable. (4) Form collaborative teams to carry out this program.

Safety-technical lay-out of the operational environment of a high-power spallation target system of the megawatt class with mercury as target material

International Nuclear Information System (INIS)

Butzek, M.

2005-06-01

of the neutron guide system. Due to the high amount of safety relevant handling procedures, concepts for time efficient and safe handling of the major components have been developed. Based on the concepts shown in this thesis, construction and operation of a high power spallation source of the described kind seem to be feasible considering safety and costs. (orig.)

Applications of ion beam analysis workshop. Workshop handbook

International Nuclear Information System (INIS)

1995-01-01

A workshop on applications of ion beam analysis was held at ANSTO, immediate prior to the IBMM-95 Conference in Canberra. It aims was to review developments and current status on use of ion beams for analysis, emphasizing the following aspects: fundamental ion beam research and secondary effects of ion beams; material sciences, geological, life sciences, environmental and industrial applications; computing codes for use in accelerator research; high energy heavy ion scattering and recoil; recent technological development using ion beams. The handbook contains the workshop's program, 29 abstracts and a list of participants

Inelastic near-surface interactions. Proceedings of the Werner Brandt workshop

International Nuclear Information System (INIS)

1985-04-01

This workshop is one of an annual series covering penetration phenomena of charged particles in matter. This specific workshop includes electron scattering, ion and atom scattering, stopping powers, and cluster ion impacts on solids. Abstracts were prepared for individual items in the proceedings for inclusion in the data base

Workshops on Writing Science

Indian Academy of Sciences (India)

2017-09-30

Sep 30, 2017 ... hands-on practice, feedback, mentoring and highly interactive sessions. The focus will be on work done as individuals and in teams. Maximum number of participants for the workshop is limited. The workshop is compulso- rily residential. Boarding and lodging free for selected candidates. Re-imbursement ...

New HOPE Pilot TM workshops in New York State : lessons learned in hydrogen education and teacher training

Energy Technology Data Exchange (ETDEWEB)

De Valladares, M.R. [M.R.S. Enterprises LLC, Bethesda, MD (United States)

2009-07-01

More than 300 New York State high school science and technology teachers participated at the New HOPE (Hydrogen Outreach Program for Education) workshops hosted by New York Energy Research Development Authority (NYSERDA), New York Power Authority (NYPA) and the Long Island Power Authority (LIPA). These teachers will impact approximately 150,000 students over the next 5 years. The teacher training was provided by M.R.S. Enterprises, LLC and its HOPE team. The workshops featured hands-on activities, such as construction of a fuel cell vehicle from everyday materials. Workshop topics ranged from hydrogen production, storage, distribution and utilization, and fuel cells. Teachers received the New HOPE Pilot TM, a user friendly curriculum with lesson plans along with 2 kits, namely a fuel cell and car chassis kit, and a HOPEMobileTM materials kit with which to continue the design and engineering process in the classroom.

Risk Management Techniques and Practice Workshop Workshop Report

Energy Technology Data Exchange (ETDEWEB)

Quinn, T; Zosel, M

2008-12-02

At the request of the Department of Energy (DOE) Office of Science (SC), Lawrence Livermore National Laboratory (LLNL) hosted a two-day Risk Management Techniques and Practice (RMTAP) workshop held September 18-19 at the Hotel Nikko in San Francisco. The purpose of the workshop, which was sponsored by the SC/Advanced Scientific Computing Research (ASCR) program and the National Nuclear Security Administration (NNSA)/Advanced Simulation and Computing (ASC) program, was to assess current and emerging techniques, practices, and lessons learned for effectively identifying, understanding, managing, and mitigating the risks associated with acquiring leading-edge computing systems at high-performance computing centers (HPCCs). Representatives from fifteen high-performance computing (HPC) organizations, four HPC vendor partners, and three government agencies attended the workshop. The overall workshop findings were: (1) Standard risk management techniques and tools are in the aggregate applicable to projects at HPCCs and are commonly employed by the HPC community; (2) HPC projects have characteristics that necessitate a tailoring of the standard risk management practices; (3) All HPCC acquisition projects can benefit by employing risk management, but the specific choice of risk management processes and tools is less important to the success of the project; (4) The special relationship between the HPCCs and HPC vendors must be reflected in the risk management strategy; (5) Best practices findings include developing a prioritized risk register with special attention to the top risks, establishing a practice of regular meetings and status updates with the platform partner, supporting regular and open reviews that engage the interests and expertise of a wide range of staff and stakeholders, and documenting and sharing the acquisition/build/deployment experience; and (6) Top risk categories include system scaling issues, request for proposal/contract and acceptance testing, and

High Efficiency Power Converter for Low Voltage High Power Applications

DEFF Research Database (Denmark)

Nymand, Morten

The topic of this thesis is the design of high efficiency power electronic dc-to-dc converters for high-power, low-input-voltage to high-output-voltage applications. These converters are increasingly required for emerging sustainable energy systems such as fuel cell, battery or photo voltaic based......, and remote power generation for light towers, camper vans, boats, beacons, and buoys etc. A review of current state-of-the-art is presented. The best performing converters achieve moderately high peak efficiencies at high input voltage and medium power level. However, system dimensioning and cost are often...

The midwest workshop on preparing nuclear engineering professionals

International Nuclear Information System (INIS)

Danofsky, R.A.; Rohach, A.F.; Spinrad, B.I.; Nodean, W.C.

1988-01-01

Personnel training and education are activities of major importance for nuclear utilities and represent fruitful areas for possible cooperation between utilities and educational institutions. Utility personnel have a need for continuing education through advanced and undergraduate degree programs and special courses. Nuclear engineering departments are in a position to meet at least some of these needs. The purpose of the workshop described in this paper was to explore ways to increase the dialogue between utilities and universities and to bring faculty and utility personnel together to discuss the educational needs of nuclear utilities. The workshop was held May 25-27, 1988, at Iowa State University. Planning for the workshop was coordinated by a steering committee with representation from the Department of Nuclear Engineering at Iowa State University, Iowa Electric Light and Power Company (IEL ampersand P), and Kirkwood Community College at Cedar Rapids, Iowa. Participants represented nuclear utilities, nuclear engineering departments, 2- and 4-yr colleges, a nuclear training organization, and the Institute of Nuclear Power Operations

PREFACE: Collapse Calderas Workshop

Science.gov (United States)

Gottsmann, Jo; Aguirre-Diaz, Gerardo

2008-10-01

Caldera-formation is one of the most awe-inspiring and powerful displays of nature's force. Resultant deposits may cover vast areas and significantly alter the immediate topography. Post-collapse activity may include resurgence, unrest, intra-caldera volcanism and potentially the start of a new magmatic cycle, perhaps eventually leading to renewed collapse. Since volcanoes and their eruptions are the surface manifestation of magmatic processes, calderas provide key insights into the generation and evolution of large-volume silicic magma bodies in the Earth's crust. Despite their potentially ferocious nature, calderas play a crucial role in modern society's life. Collapse calderas host essential economic deposits and supply power for many via the exploitation of geothermal reservoirs, and thus receive considerable scientific, economic and industrial attention. Calderas also attract millions of visitors world-wide with their spectacular scenic displays. To build on the outcomes of the 2005 calderas workshop in Tenerife (Spain) and to assess the most recent advances on caldera research, a follow-up meeting was proposed to be held in Mexico in 2008. This abstract volume presents contributions to the 2nd Calderas Workshop held at Hotel Misión La Muralla, Querétaro, Mexico, 19-25 October 2008. The title of the workshop `Reconstructing the evolution of collapse calderas: Magma storage, mobilisation and eruption' set the theme for five days of presentations and discussions, both at the venue as well as during visits to the surrounding calderas of Amealco, Amazcala and Huichapan. The multi-disciplinary workshop was attended by more than 40 scientist from North, Central and South America, Europe, Australia and Asia. Contributions covered five thematic topics: geology, geochemistry/petrology, structural analysis/modelling, geophysics, and hazards. The workshop was generously supported by the International Association of Volcanology and the Chemistry of The Earth's Interior

Discharge runaway in high power impulse magnetron sputtering of carbon: the effect of gas pressure, composition and target peak voltage

Science.gov (United States)

Vitelaru, Catalin; Aijaz, Asim; Constantina Parau, Anca; Kiss, Adrian Emil; Sobetkii, Arcadie; Kubart, Tomas

2018-04-01

Pressure and target voltage driven discharge runaway from low to high discharge current density regimes in high power impulse magnetron sputtering of carbon is investigated. The main purpose is to provide a meaningful insight of the discharge dynamics, with the ultimate goal to establish a correlation between discharge properties and process parameters to control the film growth. This is achieved by examining a wide range of pressures (2–20 mTorr) and target voltages (700–850 V) and measuring ion saturation current density at the substrate position. We show that the minimum plasma impedance is an important parameter identifying the discharge transition as well as establishing a stable operating condition. Using the formalism of generalized recycling model, we introduce a new parameter, ‘recycling ratio’, to quantify the process gas recycling for specific process conditions. The model takes into account the ion flux to the target, the amount of gas available, and the amount of gas required for sustaining the discharge. We show that this parameter describes the relation between the gas recycling and the discharge current density. As a test case, we discuss the pressure and voltage driven transitions by changing the gas composition when adding Ne into the discharge. We propose that standard Ar HiPIMS discharges operated with significant gas recycling do not require Ne to increase the carbon ionization.

Workshop of learning: a methodological proposal in the formation of the student of the High School

Directory of Open Access Journals (Sweden)

Tania Belizário Mastelari

2017-12-01

Full Text Available The main objective of the current school is to develop competences that allow the student to achieve personal and professional success, aiming to give space so that each individual can learn to use their knowledge to act efficiently. The present study aimed to investigate the skills and competences that converge to the enem structuring axes, to which the students developed when participating in a learning workshop. It was initially analyzed the convergences between the skills proposed by the workshop and those required by the official documents, such as the ENEM - National High School Examination and the CPN - National Curricular Parameters. For that, the workshop entitled "The Big Bang", developed with high school students, was analyzed. This workshop contemplates the perspective of the Natural Sciences and their Technologies, in the discipline of Biology, and for that, the convergences between the competences proposed by ENEM, PCN and the text of the workshop were raised. After this survey, we verified which of these competences were grouped in the structuring axes of the Enem: contextualization, interdisciplinarity and problem-situation. It can be observed that the methodology provides the possibility of developing skills and abilities, however, it is emphasized that the way the workshop is worked on the importance of understanding the nuances of the teaching-learning process, the clarity of skills concepts And skills, trans and interdisciplinarity, and especially how the Curriculum Guidelines are implicated in the whole educational context, must make sense of the criteria that teachers must use to achieve the pedagogical objectives, however, these indicators are often not clear In the teaching-learning process for educators, making it necessary to raise awareness so that the action of teaching is more effective.

Challenges of radiotherapy: report on the 4D treatment planning workshop 2013

NARCIS (Netherlands)

Knopf, Antje; Nill, Simeon; Yohannes, Indra; Graeff, Christian; Dowdell, Stephen; Kurz, Christopher; Sonke, Jan-Jakob; Biegun, Aleksandra K; Lang, Stephanie; McClelland, Jamie R.; Champion, Benjamin; Fast, Martin; Wölfelschneider, Jens; Gianoli, Chiara; Rucinski, Antoni; Baroni, Guido; Richter, Christian; van de Water, Steven; Grassberger, Clemens; Weber, Damien; Poulsen, Per; Shimizu, Shinichi; Bert, Christoph

2014-01-01

This report, compiled by experts on the treatment of mobile targets with advanced radiotherapy, summarizes the main conclusions and innovations achieved during the 4D treatment planning workshop 2013. This annual workshop focuses on research aiming to advance 4D radiotherapy treatments, including

Stopping power. Projectile and target modeled as oscillators

International Nuclear Information System (INIS)

Stevanovic, N.; Nikezic, D.

2005-01-01

In this Letter the collision of two quantum harmonic oscillators was considered. The oscillators interact through the Coulomb interaction. Stopping power of projectile was calculated assuming that both, target and projectile may be excited. It has been shown that the frequency of the projectile oscillation, ω p influences on stopping power, particularly in the region of Bragg peak. If, ω p ->0 is substitute in the expression for stopping power derived in this Letter, then it comes to the form when the projectile has been treated as point like charged particle

Optical design of high power excimer laser system

International Nuclear Information System (INIS)

Zhang Yongsheng; Zhao Jun; Ma Lianying; Yi Aiping; Liu Jingru

2011-01-01

Image relay and angular multiplexing,which should be considered together in the design of high power excimer laser system, is reviewed. It's important to select proper illumination setup and laser beam shaping techniques. Given the complex and special angular multiplexing scheme in high power excimer laser systems, some detailed conceptual layout schemes are given in the paper. After a brief description of lens array and reflective telescope objective, which combine the incoming beams to a common focus, a new schematic layout which uses the final targeting optics and one optical delay line array, to realize multiplexing and de-multiplexing simultaneously is first proposed in the paper. (authors)

Baltic Nuclear workshop. Final report[Crisis communication

Energy Technology Data Exchange (ETDEWEB)

Wahlberg, L.G

2001-05-01

Proceedings of the NKS/BOK-1.6 workshop on crisis communication 'Baltic Nuclear', held in Stockholm March 19 -20, 2001, with participants from the nuclear power plants and nuclear authorities in the Baltic Sea region. The main content of the workshop was founded on the principle of 'learning by doing'. The participants were therefore practically trained in how to handle a crisis from an information and communication point of view. Added to that there were three different lectures. (au)

Module Integrated GaN Power Stage for High Switching Frequency Operation

DEFF Research Database (Denmark)

Nour, Yasser; Knott, Arnold

2017-01-01

is integrated on a high glass transition temperature 0.4 mmthick FR4 substrate configured as a 70 pin ball grid arraypackage. The power stage is tested up to switching frequency of12 MHz. The power stage achieved 88.5 % peak efficiency whenconfigured as a soft switching buck converter operating at 7MHz......An increased attention has been detected todevelop smaller and lighter high voltage power converters in therange of 50 V to 400 V domains. The applications for theseconverters are mainly focused for Power over Ethernet (PoE),LED lighting and ac adapters. Design for high power density isone...... of the targets for next generation power converters. Thispaper presents an 80 V input capable multi-chip moduleintegration of enhancement mode gallium nitride (GaN) fieldeffect transistors (FETs) based power stage. The module design ispresented and validated through experimental results. The powerstage...

Summary of the ORNL-sponsored reactor radwaste management workshop

International Nuclear Information System (INIS)

Kibbey, A.H.

1977-01-01

On January 12 to 14, 1977, Oak Ridge National Laboratory (ORNL) sponsored a Radwaste Management Workshop in New Orleans, Louisiana, the object of which was to obtain operating data on the uses of evaporation, ion exchange, filtration, and on solid radwaste practices at nuclear power plants. The collected data are being used to update three earlier generic reports done by ORNL on the status of evaporation, ion exchange, and solid radwaste practices at nuclear power plants and to prepare a new one on filtration. All segments of the nuclear power industry were invited to participate, and a total of 188 representatives came. There were four major Workshop groups: volume reduction, solidification, physical and chemical separations, and corrosion. The major findings of each group are reported

Transcript of the workshop to discuss plans for a National High Intensity Radioactive Nuclear Beam Facility

International Nuclear Information System (INIS)

Nitschke, J.M.

1989-01-01

Following the ''First International Conference on Radioactive Nuclear Beams'' in Berkeley, a workshop was held on October 19, 1989 at the Lawrence Berkeley Laboratory to discuss plans for a National High Intensity Radioactive Nuclear Beam (RNB) Facility. The purpose of the workshop was -- after having discussed during the conference the physics question that can be addressed with RNBs -- to evaluate more concretely the possibilities for actually constructing such a facility in this country. It is becoming increasingly apparent that facility producing beams of radioactive nuclei with extreme neutron-to-proton ratios is of high scientific interest and technically feasible. It would allow the study of nuclear structure and astrophysical reactions very far from the line of stable nuclei, and could provide new possibilities of reaching the long-sought island of stability of superheavy nuclei. Such facilities are under advanced consideration in Japan and at CERN in Europe. This paper contains a slightly edited transcript of the tape recording that was made of the workshop

Vulcano Workshop 2016

CERN Document Server

Mannocchi, G.; Morselli, A.; Trinchero, G.

2016-01-01

We announce the XVI Vulcano Workshop, which will be held from May 22nd to May 28th, 2016 in the Vulcano Island (Sicily, Italy). As in the past editions, the workshop will aim to gather people from High Energy Astrophysics and Particle Physics to discuss the most recent highlights in these fields. The workshop will cover the following topics: Astrophysics/Cosmology, Astrophysics/Gravity, Dark Matter, Particle Physics, Cosmic Rays, Gamma/Neutrino Astronomy, Neutrinos and Future Prospects. The scientific program will include several 30-minute review talks, to introduce the current problems, and 20-minute talks, giving new experimental and theoretical results. The participation is by invitation and limited to 80 people.

The QED Workshop

Energy Technology Data Exchange (ETDEWEB)

Pieper, G.W.

1994-07-01

On May 18--20, 1994, Argonne National Laboratory hosted the QED Workshop. The workshop was supported by special funding from the Office of Naval Research. The purpose of the workshop was to assemble of a group of researchers to consider whether it is desirable and feasible to build a proof-checked encyclopedia of mathematics, with an associated facility for theorem proving and proof checking. Among the projects represented were Coq, Eves, HOL, ILF, Imps, MathPert, Mizar, NQTHM, NuPrl, OTTER, Proof Pad, Qu-Prolog, and RRL. Although the content of the QED project is highly technical rigorously proof-checked mathematics of all sorts the discussions at the workshop were rarely technical. No prepared talks or papers were given. Instead, the discussions focused primarily on such political, sociological, practical, and aesthetic questions, such as Why do it? Who are the customers? How can one get mathematicians interested? What sort of interfaces are desirable? The most important conclusion of the workshop was that QED is an idea worthy pursuing, a statement with which virtually all the participants agreed. In this document, the authors capture some of the discussions and outline suggestions for the start of a QED scientific community.

Support of A Summer School Workshop and Workshop Focused on Theory and Applications of Time-Dependent Density Functional Theory

Energy Technology Data Exchange (ETDEWEB)

Maitra, Neepa [City Univ. (CUNY), NY (United States). Dept. of Physics

2017-08-31

The first US-based summer school and workshop on Time-Dependent Density Functional Theory (TDDFT) was held July 11-21, 2017 in Telluride, CO. This grant provided funding to enable 33 students to attend the school, specifically with lodging and registration fee reductions. TDDFT is increasingly used in computational molecular and materials science to calculate electronic-excitation spectra and dynamics in a wide variety of applications, including photocatalysis, photo-controlled bond dissociation, and light-induced charge transfer. Software development in this community targets multiple software packages, many of which are open source, such as octopus, NWchem and Qb@ll, which are the ones our school focused on. The goal of this first iteration was to create a home for a national community of scholars, including users and developers, with a deep understanding of TDDFT, its capabilities, limitations, and high-performance computing context. We used this opportunity to explore interest in such an event in the future and based on overwhelmingly positive feedback from students and teachers, we intend to hold a similar school+workshop every two years in the US, in order to maintain the high level of interest that we witnessed and the enthusiasm amongst participants.

Proceedings of the 1st International Workshop on High-Speed and Intercity Railways

CERN Document Server

Ye, Xiao-Wei

2012-01-01

This book contains the papers included in the proceedings of the 1st International Workshop on High-speed and Intercity Railways (IWHIR 2011) held in Shenzhen and Hong Kong, China from July 19 to July 22, 2011, which is organized by The Hong Kong Polytechnic University, in collaboration with Southwest Jiaotong University, Beijing Jiaotong University, Dalian Jiaotong University, China Engineering Consultants, Inc., Zhejiang University, and Tsinghua University. Continuing the great initiatives and momentums of the rapid development in high-speed and intercity railways worldwide in recent years, IWHIR 2011 aims at providing a platform for academic scholars and practicing engineers to share knowledge and experience, to promote collaboration, and to strengthen R&D activities related to railway engineering. Engineers, scientists, professors, and students from universities, research institutes, and related industrial companies have been cordially invited to participate in the workshop. These papers have covered ...

NEA International Workshop on the Nuclear Innovation Road-map - NI2050. Workshop proceedings

International Nuclear Information System (INIS)

Ait Abderrahim, Hamid; Fernandez Fernandez, Alberto; Van Walle, Eric; Speranzini, Robert; Zezula, Lubor; Puska, Eija Karita; Tuomisto, Harri; Al Mazouzi, Abderrahim; Bazile, Fanny; Cordier, Pierre-Yves; Wahide, Carole; Tromm, Th. Walter; Horvath, Akos; Agostini, Pietro; Ambrosini, Walter; Kamide, Hideki; Nakatsuka, Toru; Sagayama, Yutaka; Tsujimoto, Kazufumi; Jeong, Ik; LEE, Gye Seok; Roelofs, Ferry; Van Der Lugt, Hermen; Wrochna, Grzegorz; Alekseev, Pavel; Andreeva-Andrievskaya, Lyudmila N.; Liska, Peter; Cizelj, Leon; Castelao Lopez, Carlos; Zimmermann, Martin; Rayment, Fiona; Pasamehmetoglu, Kemal; Martin Ramos, Manuel; Schmitz, Bruno; Monti, Stefano; Bignan, Gilles; Mcgrath, Margaret; Caron-Charles, Marylise; Magwood, William IV; Ha, Jaejoo; Deffrennes, Marc; Paillere, Henri; Noh, Jae Man; Gulliford, Jim; Breest, Axel; Matsumoto, Kiyoshi; Lebedev, Vladimir

2015-07-01

The two-day workshop held at the OECD Headquarters in Paris on 7-8 July 2015, brought together some of the leading experts in the field of nuclear fission research, development and demonstration. The purpose was to launch the NEA Nuclear Innovation 2050 Initiative, aiming, after a first survey phase, at producing a road-map of main priority research programs and infrastructures necessary to support the role nuclear energy may play in the low carbon power sector of the future. This might then further lead to some ad-hoc co-operation frameworks that help to effectively implement key priorities coming out of the road-mapping. The workshop was organised into the following five sessions: 1 - Opening session on NI2050: vision and main objectives; 2 - National presentations on nuclear fission research and innovation activities (programs, infrastructures, budgets); 3 - Presentations on some existing international nuclear fission road-maps and co-operation frameworks; 4 - Defining the way forward for NI2050: survey, road-mapping and priorities and co-operation; 5 - Open discussion. This document gathers the available presentations given at this workshop

Environmental radioactive monitoring, evaluation and protection in luminous workshops of a factory

International Nuclear Information System (INIS)

Dai Hanbin; Xiang Ming; Tan Jianzu

2009-01-01

Fluorescent technique is often used to display instrumental indicator in the dark environment. Luminous workshops of a factory smear and depict the glassware by means of fluorescent power with adulterated radioactive matter. Because of adulterated radioactive matters such as 226 Ra, 40 K emit alpha-ray,beta-ray and gamma-ray, while they decay spontaneously, and high dose or cumulative radiation can damage human body in different degrees. Therefore, any radioactive damage to human body caused by over-safety dose should be prevented strictly during the working. To ensure health and safety of working staff in luminous workshop and the public, it is necessary to regularly have radioactive monitoring and evaluation to luminous workshop and its surrounding environment. Through the environment radioactive monitoring, the authors analyze its environmental radioactive level,and try to find out the possible problems so as to propose some protective measures for personal health. (authors)

Deposition Rates of High Power Impulse Magnetron Sputtering: Physics and Economics

Energy Technology Data Exchange (ETDEWEB)

Anders, Andre

2009-11-22

Deposition by high power impulse magnetron sputtering (HIPIMS) is considered by some as the new paradigm of advanced sputtering technology, yet this is met with skepticism by others for the reported lower deposition rates, if compared to rates of more conventional sputtering of equal average power. In this contribution, the underlying physical reasons for the rate changes are discussed, including (i) ion return to the target and self-sputtering, (ii) the less-than-linear increase of the sputtering yield with increasing ion energy, (iii) yield changes due to the shift of species responsible for sputtering, (iv) changes to due to greater film density, limited sticking, and self-sputtering on the substrate, (v) noticeable power losses in the switch module, (vi) changes of the magnetic balance and particle confinement of the magnetron due to self-fields at high current, and (vii) superposition of sputtering and sublimation/evaporation for selected materials. The situation is even more complicated for reactive systems where the target surface chemistry is a function of the reactive gas partial pressure and discharge conditions. While most of these factors imply a reduction of the normalized deposition rate, increased rates have been reported for certain conditions using hot targets and less poisoned targets. Finally, some points of economics and HIPIMS benefits considered.

Deposition rates of high power impulse magnetron sputtering: Physics and economics

International Nuclear Information System (INIS)

Anders, Andre

2010-01-01

Deposition by high power impulse magnetron sputtering (HIPIMS) is considered by some as the new paradigm of advanced sputtering technology, yet this is met with skepticism by others for the reported lower deposition rates, if compared to rates of more conventional sputtering of equal average power. In this contribution, the underlying physical reasons for the rate changes are discussed, including (i) ion return to the target and self-sputtering, (ii) the less-than-linear increase in the sputtering yield with increasing ion energy, (iii) yield changes due to the shift of species responsible for sputtering, (iv) changes due to greater film density, limited sticking, and self-sputtering on the substrate, (v) noticeable power losses in the switch module, (vi) changes in the magnetic balance and particle confinement of the magnetron due to self-fields at high current, and (vii) superposition of sputtering and sublimation/evaporation for selected materials. The situation is even more complicated for reactive systems where the target surface chemistry is a function of the reactive gas partial pressure and discharge conditions. While most of these factors imply a reduction in the normalized deposition rate, increased rates have been reported for certain conditions using hot targets and less poisoned targets. Finally, some points of economics and HIPIMS benefits are considered.

Workshop on nuclear structure and decay data: Theory and evaluation, 2008

International Nuclear Information System (INIS)

Nichols, A.L.; McLaughlin, P.K.

2008-06-01

A two-week Workshop on Nuclear Structure and Decay Data under the auspices of the IAEA Nuclear Data Section was organised and held at the Abdus Salam International Centre for Theoretical Physics (ICTP) in Trieste, Italy from 28 April to 9 May 2008. This workshop constituted a further development of previous Nuclear Structure and Decay Data Workshops held in 2002, 2003, 2005 and 2006. The aims and contents of the 2008 workshop are summarized, along with the agenda, list of participants, comments and recommendations. All recent workshop material has been assembled in this INDC report, and is also freely available on CD-ROM (all relevant PowerPoint presentations and manuals along with appropriate computer codes). (author)

Impact of After-School Nutrition Workshops in a Public Library Setting

Science.gov (United States)

Freedman, Marjorie R.; Nickell, Audrey

2010-01-01

Objective: To determine if after-school nutrition workshops conducted in public libraries were related to lasting changes in food choice. Methods: "Snack Smart" workshops, based on Social Cognitive Theory, were conducted in 8 branch libraries (49 ethnically diverse children, ages 9 to 14) to assess changes in consumption of targeted food items by…

Proceedings of the kaon pds magnet design workshop

International Nuclear Information System (INIS)

Otter, A.J.; Strathdee, A.

1989-03-01

These proceedings bring together the papers given at the Magnet Design Workshop (October 3 - 5 ) which was held to kick off the Kaon Factory PDS which was officially started on October 1, 1988. The workshop included sessions on power supplies and measurements as well as synchrotron and kicker magnet design. The aim of the meetings was to bring together experts who could advise us on magnet and power supply techniques which, prior to the Kaon era, have not been required at TRIUMF. These include fast - cycling cyclotron magnets and their power supplies, and the kickers needed to switch the beam from one ring to another or to the experimental areas. We also invited participation from industrial companies who will be potential magnet suppliers when Kaon Factory is funded. It was a pleasure to have representatives from six industrial companies amongst the participants

Robustness of Electrical Systems of Nuclear Power Plants in Light of the Fukushima Daiichi Accident (ROBELSYS). Workshop Proceedings, Paris, France, 1-4 April 2014. Appendix 2 (Cont'd) and Appendix 3 - Robustness of Electrical Systems of NPP's in Light of the Fukushima Daiichi Accident. ROBELSYS Workshop Proceedings. Appendices 2 and 3

International Nuclear Information System (INIS)

2015-01-01

The March 2011 accident at Fukushima Daiichi triggered discussions about the significance of electrical power hazards and their treatment in safety analyses. In order to address these issues and provide relevant conclusions and recommendations to CSNI and CNRA, the Robustness in Electrical Systems (ROBELSYS) Technical Working Group was established in 2012 under the leadership of the Institut de Radioprotection et de Surete Nucleaire (IRSN) of France. The purpose of the ROBELSYS Technical Working Group was to organize an international workshop to identify and discuss the lessons learned from the Fukushima Daiichi accident. The workshop was focused on the provisions taken by various countries concerning national requirements and modifications to the plant designs in order to enhance the robustness of electrical systems, especially the protection against extreme external hazards. The ROBELSYS workshop was held at the OECD Conference Centre in Paris in April 1-4, 2014. A total of 105 participants attended the workshop representing industry and government organisations from 25 countries, as well as international organisations. A total of 34 technical presentations were given in seven sessions as follows: - 1: National Programmes on Evolution of Onsite and Offsite Electric Power Systems; - 2: Role of Electric Power in Severe Accident Management; - 3: Requirements for Robustness of Onsite Electric Power Systems; - 4: Simulation of Transients within NPP Plant Distribution Systems; - 5: Requirements for Equipment Used for Emergency Response; - 6: Margin Assessments for Modern Power Electronics; - 7: Digital Components in Power Systems. Items addressed in the workshop included: - Review of the lessons learned from the Fukushima accident concerning the robustness of electrical systems; - Review of the provisions already taken or planned after the Fukushima accident, regarding the sources, the distribution systems and the loads, and documenting the technical basis for these

Hunton Group core workshop and field trip

Energy Technology Data Exchange (ETDEWEB)

Johnson, K.S. [ed.

1993-12-31

The Late Ordovician-Silurian-Devonian Hunton Group is a moderately thick sequence of shallow-marine carbonates deposited on the south edge of the North American craton. This rock unit is a major target for petroleum exploration and reservoir development in the southern Midcontinent. The workshop described here was held to display cores, outcrop samples, and other reservoir-characterization studies of the Hunton Group and equivalent strata throughout the region. A field trip was organized to complement the workshop by allowing examination of excellent outcrops of the Hunton Group of the Arbuckle Mountains.

Proceedings of the workshop on data acquisition system for high energy physics

International Nuclear Information System (INIS)

Hayano, R.S.

1984-09-01

The workshop ''Data acquisition system for high energy experiment'' was held by the on-line electronics group of KEK in cooperation with the data processing section on May 28-29, 1984, at KEK. This year, the proton synchrotron is prepared for the work after shutdown, and in the TRISTAN, the full scale construction of the data acquisition system is advanced. One of the large topics was the TKO box proposed by the data acquisition development group of KEK, and its specification is included in this book. This workshop was the meeting with very wide range from front end electronics to large computers. The talks on flash analog/digital converters and latest data communication were held. As a new trial, the wish lists on the future development and support of on-line electronics and others were collected from the participants, and these were deliberated by all the members. The contents of the discussion at this time are given in this book. The summaries of the lectures presented at the meeting are collected in this book. The interchange with the experimental group is indispensable for the activities of the on-line electronics group, accordingly, the workshop like this will be held hereafter. (Kako, I.)

Results from core-edge experiments in high Power, high performance plasmas on DIII-D

Directory of Open Access Journals (Sweden)

T.W. Petrie

2017-08-01

Full Text Available Significant challenges to reducing divertor heat flux in highly powered near-double null divertor (DND hybrid plasmas, while still maintaining both high performance metrics and low enough density for application of RF heating, are identified. For these DNDs on DIII-D, the scaling of the peak heat flux at the outer target (q⊥P ∝ [PSOL x IP] 0.92 for PSOL= 8−19MW and IP= 1.0–1.4MA, and is consistent with standard ITPA scaling for single-null H-mode plasmas. Two divertor heat flux reduction methods were tested. First, applying the puff-and-pump radiating divertor to DIII-D plasmas may be problematical at high power and H98 (≥ 1.5 due to improvement in confinement time with deuterium gas puffing which can lead to unacceptably high core density under certain conditions. Second, q⊥P for these high performance DNDs was reduced by ≈35% when an open divertor is closed on the common flux side of the outer divertor target (“semi-slot” but also that heating near the slot opening is a significant source for impurity contamination of the core.

High Resolution Infrared Spectroscopy in Astronomy Proceedings of an ESO Workshop Held at Garching, Germany, 18-21 November 2003

CERN Document Server

Käufl, Hans Ulrich; Moorwood, Alan F. M

2005-01-01

Two specialized new instruments for ESO's VLT, VISIR and CRIRES, spawned the idea for this workshop. CRIRES is a dedicated very high resolution infrared spectrograph; VISIR features a high resolution spectroscopic mode. Together, the instruments combine the sensitivity of an 8m-telescope with the now well-established reliability of VLT-facility instruments. High resolution here means that lines in cool stellar atmospheres and HII-regions can be resolved. The astrophysical topics discussed in this rather specialized workshop range from the inner solar system to active galactic nuclei. There are many possibilities for new discoveries with these instruments, but the unique capability, which becomes available through high-resolution infrared spectroscopy, is the observation of molecular rotational-vibrational transitions in many astrophysical environments. Particularly interesting and surprising in this context, many papers on modeling and laboratory spectroscopy at the workshop appear to indicate that astronomic...

Proceedings of the workshop on opportunities for atomic physics using slow, highly-charged ions

International Nuclear Information System (INIS)

1987-01-01

The study of atomic physics with highly-charged ions is an area of intense activity at the present time because of a convergence of theoretical interest and advances in experimental techniques. The purpose of the Argonne ''Workshop on Opportunities for Atomic Physics Using Slow, Highly-Charged Ions'' was to bring together atomic, nuclear, and accelerator physicists in order to identify what new facilities would be most useful for the atomic physics community. The program included discussion of existing once-through machines, advanced ion sources, recoil ion techniques, ion traps, and cooler rings. One of the topics of the Workshop was to discuss possible improvement to the ANL Tandem-Linac facility (ATLAS) to enhance the capability for slowing down ions after they are stripped to a high-charge state (the Accel/Decel technique). Another topic was the opportunity for atomic physics provided by the ECR ion source which is being built for the Uranium Upgrade of ATLAS. 18 analytics were prepared for the individual papers in this volume

International workshop on advanced materials for high precision detectors. Proceedings

International Nuclear Information System (INIS)

Nicquevert, B.; Hauviller, C.

1994-01-01

These proceedings gather together the contributions to the Workshop on Advanced Materials for High Precision Detectors, which was held from 28-30 September 1994 in Archamps, Haute-Savoie, France. This meeting brought together international experts (researchers, physicists and engineers) in the field of advanced materials and their use in high energy physics detectors or spacecraft applications. Its purpose was to discuss the status of the different materials currently in use in the structures of detectors and spacecraft, together with their actual performances, technological implications and future prospects. Environmental effects, such as those of moisture and radiation, were discussed, as were design and manufacturing technologies. Some case studies were presented. (orig.)

Nuclear Fuel Behaviour during Reactivity Initiated Accidents. Workshop Proceedings

International Nuclear Information System (INIS)

2010-01-01

A reactivity initiated accident (RIA) is a nuclear reactor accident that involves an unwanted increase in fission rate and reactor power. The power increase may damage the reactor core. The main objective of the workshop was to review the current status of the experimental and analytical studies of the fuel behavior during the RIA transients in PWR and BWR reactors and the acceptance criteria for RIA in use and under consideration. The workshop was organized in an opening session and 5 technical sessions: 1) Recent experimental results and experimental techniques used; 2) Modelling and Data Interpretation; 3) Code Assessment; 4) RIA Core Analysis and 5) Revision and application of safety criteria

Proceedings of the workshop on future control station designs and human performance issues in nuclear power plants

International Nuclear Information System (INIS)

2007-01-01

The nuclear community is currently at a stage where new reactors are being built, advanced reactors are being planned, and existing reactors are undergoing various forms of modernization of their control stations. Nuclear power plants are characterised by a high degree of complexity, where efficient and safe performance is dependent on both a sound technical design and effective teamwork and work practices. Team interactions have long traditions in current nuclear power plants. The way people operate and maintain the plants may need to accommodate technical advances associated with control station modernization and advanced plant control stations. The nuclear community likely to see the introduction of new designs, new tools to support the staff, changes to staffing types and levels, concepts of operation for new reactors that are different from current reactors, e.g., multi-unit control, possible remote operation, distributed decision making, and cooperation across distances. Based on recent experience, there is limited knowledge about human performance issues with regard to upgraded control rooms. However, even less knowledge exists regarding operation and maintenance of control stations for future and more advanced reactor designs. In order to explore these issues, the CSNI Special Experts' Group on Human and Organisational Factors (SEGHOF), now the Working Group on Human and Organizational Factors (WGHOF), and the Halden Reactor Project (HRP) hosted a joint workshop which provided an international forum for utilities, vendors, research bodies and regulators to discuss human performance issues related to control stations for future nuclear power plant designs and for modified control rooms for existing plants. The Norwegian petroleum industry also shared their experiences, especially with integrated and distributed operations among off-shore and on-shore control centres. There were 74 participants from 20 countries at the workshop. Twenty-two papers were

Proceedings of the CNRA/CSNI workshop on steam generator tube integrity in nuclear power plants

International Nuclear Information System (INIS)

Diercks, D.R.

1997-02-01

The objective of the workshop was to provide a working forum for the exchange of information by contributing experts on current issues related to PWR steam generator tube integrity. One hundred persons from 15 countries attended the workshop, including 36 from regulatory and nuclear policy agencies, 28 from research and development laboratories, 18 from nuclear vendors and consulting firms, and 18 from electrical utilities. The workshop opened with a plenary session; the first part of the session covered international steam generator regulatory practices and issues, featuring speakers from regulatory bodies in Belgium, France, Japan, Spain, and the US. In Part 2 of the plenary session, comprehensive technical overviews on steam generator tubing degradation, inspection, and integrity were presented by authorities in these fields from the US, France, and Belgium. Parallel working sessions on the second and third days of the workshop then developed findings and recommendations in the areas of (1) tubing degradation, (2) tubing inspection, (3) tubing integrity, (4) preventative and corrective measures, and (5) operational aspects and risk analysis. On the final day of the workshop, the working-session facilitators presented summaries of their sessions to the workshop attendees. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database

Proceedings of the CNRA/CSNI workshop on steam generator tube integrity in nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Diercks, D.R. [Argonne National Lab., IL (United States)

1997-02-01

The objective of the workshop was to provide a working forum for the exchange of information by contributing experts on current issues related to PWR steam generator tube integrity. One hundred persons from 15 countries attended the workshop, including 36 from regulatory and nuclear policy agencies, 28 from research and development laboratories, 18 from nuclear vendors and consulting firms, and 18 from electrical utilities. The workshop opened with a plenary session; the first part of the session covered international steam generator regulatory practices and issues, featuring speakers from regulatory bodies in Belgium, France, Japan, Spain, and the US. In Part 2 of the plenary session, comprehensive technical overviews on steam generator tubing degradation, inspection, and integrity were presented by authorities in these fields from the US, France, and Belgium. Parallel working sessions on the second and third days of the workshop then developed findings and recommendations in the areas of (1) tubing degradation, (2) tubing inspection, (3) tubing integrity, (4) preventative and corrective measures, and (5) operational aspects and risk analysis. On the final day of the workshop, the working-session facilitators presented summaries of their sessions to the workshop attendees. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

Development of Discrete Power Supply with Charge Pump Method for High Powered Sonar System

Directory of Open Access Journals (Sweden)

Kristian Ismail

2012-07-01

Full Text Available Power supply is one of the electronic devices that can provide electric energy for electronic systems or other systems. There are several types of power supplies that can be applied depend on the requirement and functions. One example is the use of power supply for sonar systems. Sonar system is a device which can be used to detect a target under water. The sonar system is an electronic circuit that requires a power supply with specific characteristics when the sonar functions as a transmitter and a receiver in the specific span time (when on and the specific lag time (when off. This paper discusses the design of power supply for high-powered sonar systems with discrete methods in which high power supply is only applied when the acoustic waves radiated under water. Charge pump was used to get the appropriate output voltage from lower input voltage. Charge pump utilized a combination of series and parallel connections of capacitors. The working mode of this power supply used the lag time as the calculation of time to charge charge pump capacitors in parallel while the span time was used for the calculation of discharging the charge pump capacitors in series.

Summer 1994 Computational Science Workshop. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-12-31

This report documents the work performed by the University of New Mexico Principal Investigators and Research Assistants while hosting the highly successful Summer 1994 Computational Sciences Workshop in Albuquerque on August 6--11, 1994. Included in this report is a final budget for the workshop, along with a summary of the participants` evaluation of the workshop. The workshop proceeding have been delivered under separate cover. In order to assist in the organization of future workshops, we have also included in this report detailed documentation of the pre- and post-workshop activities associated with this contract. Specifically, we have included a section that documents the advertising performed, along with the manner in which applications were handled. A complete list of the workshop participants in this section. Sample letters that were generated while dealing with various commercial entities and departments at the University are also included in a section dealing with workshop logistics. Finally, we have included a section in this report that deals with suggestions for future workshops.

System Software and Tools for High Performance Computing Environments: A report on the findings of the Pasadena Workshop, April 14--16, 1992

Energy Technology Data Exchange (ETDEWEB)

Sterling, T. [Universities Space Research Association, Washington, DC (United States); Messina, P. [Jet Propulsion Lab., Pasadena, CA (United States); Chen, M. [Yale Univ., New Haven, CT (United States)] [and others

1993-04-01

The Pasadena Workshop on System Software and Tools for High Performance Computing Environments was held at the Jet Propulsion Laboratory from April 14 through April 16, 1992. The workshop was sponsored by a number of Federal agencies committed to the advancement of high performance computing (HPC) both as a means to advance their respective missions and as a national resource to enhance American productivity and competitiveness. Over a hundred experts in related fields from industry, academia, and government were invited to participate in this effort to assess the current status of software technology in support of HPC systems. The overall objectives of the workshop were to understand the requirements and current limitations of HPC software technology and to contribute to a basis for establishing new directions in research and development for software technology in HPC environments. This report includes reports written by the participants of the workshop`s seven working groups. Materials presented at the workshop are reproduced in appendices. Additional chapters summarize the findings and analyze their implications for future directions in HPC software technology development.

WE-AB-206-03: Workshop

International Nuclear Information System (INIS)

Lu, Z.

2016-01-01

The involvement of medical physicists in diagnostic ultrasound imaging service is increasing due to QC and accreditation requirements. The goal of this ultrasound hands-on workshop is to demonstrate quality control (QC) testing in diagnostic ultrasound and to provide updates in ACR ultrasound accreditation requirements. The first half of this workshop will include two presentations reviewing diagnostic ultrasound QA/QC and ACR ultrasound accreditation requirements. The second half of the workshop will include live demonstrations of basic QC tests. An array of ultrasound testing phantoms and ultrasound scanners will be available for attendees to learn diagnostic ultrasound QC in a hands-on environment with live demonstrations and on-site instructors. The targeted attendees are medical physicists in diagnostic imaging. Learning Objectives: Gain familiarity with common elements of a QA/QC program for diagnostic ultrasound imaging dentify QC tools available for testing diagnostic ultrasound systems and learn how to use these tools Learn ACR ultrasound accreditation requirements Jennifer Walter is an employee of American College of Radiology on Ultrasound Accreditation.

Working Group VI Summary Report: New Ideas Employing High-Power Lasers

International Nuclear Information System (INIS)

Leemans, W.P.

1999-01-01

The objectives of this working group were to provide the ''Future Light Source Community'' information on: Electron-Laser interaction based sources; Plasma based radiation sources and accelerators; and Present and future high-power laser technology. A summary of presentations, discussions and opinions is presented next. At the end of this report, a few references are given. The list is very far from being complete but is meant as a start for further exploring the various topics discussed in this working group. Based on presentations and discussions during the workshop, a summarizing table of the performance of three different types of laser systems has been made. The emphasis is on listing performance parameters of solid state, FEL and gas based lasers, relevant to the development of a future fourth generation light source. Two types of solid state lasers capable of producing peak power in the multi-terawatt range are described: Nd:glass and Ti:sapphire lasers [1]. The main development for these lasers is towards higher average power levels: from the 10 W to the > 100 W level. An infrared FEL has recently produced 1 kW average power but with peak power on the order of 0.1 GW [2]. A terawatt class, short pulse CO 2 based gas laser is under development at the Advanced Test Facility at BNL [3

Workshop on accelerator magnet superconductors. Proceedings

International Nuclear Information System (INIS)

2004-01-01

The workshop on accelerator magnet superconductors has gathered 102 registered participants from research laboratories, universities and industry. 8 European companies, active in superconducting materials and cables were present. This workshop has been organized to deal with the status of the world research and development on superconducting materials and cables for high field magnets (B > 10 T). The workshop has also reviewed the status of high temperature superconductors and transmission line cables for potential use in low field superconducting magnets for injectors and beam transfer lines, as well as cables for pulsed magnets that might be used in future hadron colliders or injectors

Workshop on accelerator magnet superconductors. Proceedings

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

The workshop on accelerator magnet superconductors has gathered 102 registered participants from research laboratories, universities and industry. 8 European companies, active in superconducting materials and cables were present. This workshop has been organized to deal with the status of the world research and development on superconducting materials and cables for high field magnets (B > 10 T). The workshop has also reviewed the status of high temperature superconductors and transmission line cables for potential use in low field superconducting magnets for injectors and beam transfer lines, as well as cables for pulsed magnets that might be used in future hadron colliders or injectors.

8th International Workshop on Top Quark Physics

CERN Document Server

2015-01-01

This workshop, at its 8th edition, will bring together the community of experimental and theoretical physicists working on top quark physics, 20 years after its first discovery, and at the beginning of the exploration of the new energy regime at the Large Hadron Collider. The workshop will provide a comprehensive overview of the latest results from the LHC and Tevatron experiments as well as the most recent theoretical developments and an outlook on top-quark physics at future colliders. The programme will consist of plenary presentations, a poster session and 'question and answers' sessions, targeted for young researchers. A significant fraction of the workshop time will be devoted to discussions. The goal of the workshop is to provide a comprehensive picture of top-quark physics and a forum where experimentalists and theorists can discuss the interpretation of top quark results and plan future measurements. The venue will take place in the Hotel Continental Terme, Ischia, the largest island in the bay of Na...

Development of a higher power cooling system for lithium targets.

Science.gov (United States)

Phoenix, B; Green, S; Scott, M C; Bennett, J R J; Edgecock, T R

2015-12-01

The accelerator based Boron Neutron Capture Therapy beam at the University of Birmingham is based around a solid thick lithium target cooled by heavy water. Significant upgrades to Birmingham's Dynamitron accelerator are planned prior to commencing a clinical trial. These upgrades will result in an increase in maximum achievable beam current to at least 3 mA. Various upgrades to the target cooling system to cope with this increased power have been investigated. Tests of a phase change coolant known as "binary ice" have been carried out using an induction heater to provide a comparable power input to the Dynamitron beam. The experimental data shows no improvement over chilled water in the submerged jet system, with both systems exhibiting the same heat input to target temperature relation for a given flow rate. The relationship between the cooling circuit pumping rate and the target temperature in the submerged jet system has also been tested. Copyright © 2015 Elsevier Ltd. All rights reserved.

International Workshop "Groups, Rings, Lie and Hopf Algebras"

CERN Document Server

2003-01-01

The volume is almost entirely composed of the research and expository papers by the participants of the International Workshop "Groups, Rings, Lie and Hopf Algebras", which was held at the Memorial University of Newfoundland, St. John's, NF, Canada. All four areas from the title of the workshop are covered. In addition, some chapters touch upon the topics, which belong to two or more areas at the same time. Audience: The readership targeted includes researchers, graduate and senior undergraduate students in mathematics and its applications.

Power load limits of the WENDELSTEIN 7-X target elements-comparison of experimental results and design values for power loads up to the critical heat flux

International Nuclear Information System (INIS)

Greuner, H; Boeswirth, B; Boscary, J; Leuprecht, A; Plankensteiner, A

2007-01-01

The power load limits of the WENDELSTEIN7-X divertor target elements were experimentally evaluated with heat loads considerably exceeding the expected operating conditions. The water-cooled elements are designed for steady-state heat flux of 10 MW m -2 and to remove a power load up to 100 kW. The elements must allow a limited operation time at 12 MW m -2 steady-state and should not fail for short pulses of up to 15 MW m -2 for cooling conditions in the subcooled nucleate boiling regime. In the framework of the qualification phase, pre-series target elements were loaded up to 24 MW m -2 without loss of CFC tiles. A critical heat flux at the target of 31 MW m -2 was achieved. The paper discusses the results of the tests performed at the high heat flux test facility GLADIS. The experimental results compared to transient nonlinear fine element method (FEM) calculations confirm a high thermal safety margin of the target design sufficient for plasma operation in W7-X

Preface: Workshop on Off-Grid Technology Systems

Science.gov (United States)

Alonso-Marroquin, Fernando

2017-06-01

Off-grid houses are dwellings that do not rely on water supply, sewer, or electrical power grid, and are able to operate independently of all public utility services. These houses are ideal for remote communities or population suffering natural or human-made disasters. Our aim is to develop compact and affordable off-grid technologies by integrating high-end nano-engineering with systems that imitates natural biological processes. The key areas of focus in the workshop were: solar energy harvesting using nanotechnology, wind energy harvesting from vertical-axis wind turbines, supercapacitors energy storage systems, treatment of greywater, and green roofs to achieve air comfort.

Coping with Conflict and Change in Our Global Society. Report of a Summer 1972 Workshop.

Science.gov (United States)

Diablo Valley Education Project, Orinda, CA.

A five-week summer workshop offered inservice training to twenty-eight intermediate and high school social studies and English teachers. Participants examined the concepts of conflict, power and authority, identity, and interdependence through content and team working sessions, ranging from games to lectures, and independent study in an effort to…

High Efficiency Power Converter for Low Voltage High Power Applications

DEFF Research Database (Denmark)

Nymand, Morten

The topic of this thesis is the design of high efficiency power electronic dc-to-dc converters for high-power, low-input-voltage to high-output-voltage applications. These converters are increasingly required for emerging sustainable energy systems such as fuel cell, battery or photo voltaic based...

National power grid simulation capability : need and issues

Energy Technology Data Exchange (ETDEWEB)

Petri, Mark C. [Argonne National Lab. (ANL), Argonne, IL (United States)

2009-06-02

On December 9 and 10, 2008, the Department of Homeland Security (DHS) Science and Technology Directorate sponsored a national workshop at Argonne National Laboratory to explore the need for a comprehensive modeling and simulation capability for the national electric power grid system. The workshop brought together leading electric power grid experts from federal agencies, the national laboratories, and academia to discuss the current state of power grid science and engineering and to assess if important challenges are being met. The workshop helped delineate gaps between grid needs and current capabilities and identify issues that must be addressed if a solution is to be implemented. This report is a result of the workshop and highlights power grid modeling and simulation needs, the barriers that must be overcome to address them, and the benefits of a national power grid simulation capability.

Proceedings of the first geochemical workshop on shale: Environmental Sciences Division publication No. 2845

International Nuclear Information System (INIS)

Brookins, D.G.; Stow, S.H.

1986-12-01

This report represents the outcome of the first workshop dealing with geochemical research needs for a shale-hosted repository for disposal of high-level nuclear waste. The workshop was held at the University of New Mexico in 1985 and was attended by scientists representing academia, national laboratories, and the federal government. Research needs are grouped into three major categories: (1) characterization of baseline conditions, (2) radioelement behavior: ambient conditions, and (3) effect of waste emplacement. Within each category, specific needs are identified and discussed. For each, statements of justification, approach, and man-power requirements are presented. General levels of priorities are established for each research need

Proceedings of workshop on K-decay experiments

International Nuclear Information System (INIS)

Nakai, Kozi

1989-08-01

The elementary particle experiment using the 12 GeV proton synchrotron in the National Laboratory for High Energy Physics (KEK) develops centering around the large scale experiment on K-meson decay. In this case, the ideal precision physics is pursued, and efforts have been exerted to improve the experimental techniques. At present the experiment on searching for rare K-decay is advancing. Next, the experiment on searching for CP nonconservation process will be begun. However, these experiments are in severe competition with those in BNL and Fermilab which have powerful accelerators, therefore it is desirable to grasp well the development of the international research plans. Therefore, in order to obtain the quideline for the experimental plan using the KEK proton synchrotron hereafter, the workshop on K-decay was held on July 11∼12, 1989. In this workshop, Arisaka (UCLA), Numao (TRIUMF) and Yamanaka (Fermilab) returned from USA and lectured on the present status of the experiment and the future perspective. The impression of the planner of the proton synchrotron experiment plan on the experiments are recorded. (K.I.)

IAEA workshop on the year 2000 issue (Y2K)

International Nuclear Information System (INIS)

1999-01-01

The document gives the highlights of the workshop conducted by the IAEA from 12 to 16 July 1999 to assist its Member States on the challenge that the Year 2000 issue (Y2K) presents to operators and regulators of nuclear power plants. The workshop was attended by 52 participants and lecturers from 21 countries and from the World Association of Nuclear Operators (WANO)

Point Climat no. 21 'Regional wind power plans: is there enough wind to reach the Grenelle wind power targets?'

International Nuclear Information System (INIS)

Bordier, Cecile; Charentenay, Jeremie de

2012-01-01

Among the publications of CDC Climat Research, 'Climate Briefs' presents, in a few pages, hot topics in climate change policy. This issue addresses the following points: Regional wind power plans assess the wind power development potential of every French region. The aggregate regional potential largely exceeds national targets for 2020. However, achieving these targets is still far from guaranteed: the forecasted potential is theoretical, and the issues involved in implementing wind power projects on the ground will likely reduce this potential

Stopping power and range relations for low and high Z ions in solids: a critical analysis

International Nuclear Information System (INIS)

Virk, H.S.; Randhawa, G.S.

1997-01-01

A critical analysis of various stopping power and range formulations has been made by comparing the calculated stopping power and range values with corresponding experimental values for different low Z (1≤Z≤8) and high Z projectiles (54≤Z≤92) in different targets, e.g. Be, C, Al, Au, Pb, CR-39, Lexan, Mylar, LR-115, CH, (CH)n, TRIFOL-TN, etc. atvarious low and high energies. A comparative study has been made by taking into consideration different target and projectile combinations, e.g., heavy ion-light target, light ion-heavy target and light ion -light target etc., Overall the Ziegler formulation (TRIM-95) provides the best agreement with the experimental results for all projectile and target combinations except for heavy ion-light target combination where it underestimates the stopping power data and overestimates the range data in the range, 2-50 MeV/u. Mukherjee and Nayak formulation totally fails at relativistic and low energies of the projectile, irrespective of the projectile-target combination. Northcliffe and Schilling formulation does not show any particular trend. Benton and Henke formulation gives good agreement between experimental and theoretical data within the range of experimental errors. (orig.)

Proceedings of the workshop on two-nucleon system

International Nuclear Information System (INIS)

Kawaguchi, Masaaki; Namiki, Mikio; Fukawa, Mineo; Masaike, Akira

1980-08-01

The workshop on two nucleon system started its works four years ago to promote the experiment project on nucleon-nucleon system in the National Laboratory for High Energy Physics by the close cooperation of experimenters and theorists. In particular, several proposals have been made about the experiments using the polarized targets of hydrogen and deuterium, the spectrometers of large solid angle and others, and the investigation into them have been forwarded. It was decided to publish the results of the fourth meeting held in the National Laboratory for High Energy Physics on October 19 and 20, 1979, as the interim report, summarizing the contents. Some of the initial objectives have not been realized yet, but the data have been produced gradually from the experiments in the National Laboratory for High Energy Physics, and are contributing to various analyses. This report is composed of the physics of nucleon-nucleon systems and anti-nucleon-nucleon systems, the results of experiments and the projects corresponding to them, and the hypothetic round-table talk on the points which this workshop considers as problematic and the views of outside researchers on the National Laboratory for High Energy Physics. Finally, the materials distributed at the time of the meeting are added for reference as the appendix. Some numerical values are mutually different, but adjustment was not made. (Kako, I.)

77 FR 31371 - Public Workshop: Privacy Compliance Workshop

Science.gov (United States)

2012-05-25

... presentations, including the privacy compliance fundamentals, privacy and data security, and the privacy... DEPARTMENT OF HOMELAND SECURITY Office of the Secretary Public Workshop: Privacy Compliance... Homeland Security Privacy Office will host a public workshop, ``Privacy Compliance Workshop.'' DATES: The...

First International Workshop on Grid Simulator Testing of Wind Turbine

Science.gov (United States)

utilities to exchange knowledge, discuss experiences, and identify needs in wind power grid compliance , multi-megawatt power electronic grid simulator systems capable of many types of grid compliance testing renewable energy technologies. Knowledge from the workshop will help guide the research and testing

PREFACE: PASREG 2003: International Workshop on Processing and Applications of Superconducting (RE)BCO Large Grain Materials

Science.gov (United States)

Murakami, Masato; Cardwell, David; Salama, Kamel; Krabbes, Gernot; Habisreuther, Tobias; Gawalek, Wolfgang

2005-02-01

Superconducting melt-textured bulk (RE)BCO large grain materials are one of the most promising materials for power applications of high temperature superconductivity at the liquid nitrogen temperature range. Industrial applications are expected in high-speed low-loss magnetic bearings for flywheel energy storage devices, high-dynamic high-torque electric reluctance motors, and MAGLEV transportation systems. The material has high magnetic field trapping capability and therefore a new class of high-field superconducting permanent magnets will soon appear. However, there is still the need to improve the magnetic and mechanical material properties, as well as to increase the single domain size. This special issue contains papers concerning these topics presented at the International Workshop on the Processing and Applications of Superconducting (RE)BCO Large Grain Materials. The workshop was held on the 30 June-2 July 2003 in Jena, Germany, and was organized by the Institut fuer Physikalische Hochtechnologie, Jena. It was the fourth in the series of PASREG workshops after Cambridge, UK (1997), Morioka, Japan (1999), and Seattle, USA (2001). Sixty two contributions were presented at the workshop, 38 oral presentations and 24 poster presentations. This special issue contains 42 papers. The editors are grateful for the support of many colleagues who reviewed the manuscripts to guarantee their high technical quality. The editors also wish to thank Doris Litzkendorf and Tobias Habisreuther from Institut fuer Physikalische Hochtechnologie, Jena, for their assistance with the organization and handling of the manuscripts. Many thanks to the workshop co-chairman Gernot Krabbes from Leibniz-Institut fuer Festkoerper und Werkstoffforschung, Dresden, for hosting the workshop participants in Dresden. Finally, all attendees wish to acknowledge the efforts of Wolfgang Gawalek, Tobias Habisreuther, Doris Litzkendorf and the Team of Department Magnetics from the Institut fuer

Characterization of high performance silicon-based VMJ PV cells for laser power transmission applications

Science.gov (United States)

Perales, Mico; Yang, Mei-huan; Wu, Cheng-liang; Hsu, Chin-wei; Chao, Wei-sheng; Chen, Kun-hsien; Zahuranec, Terry

2016-03-01

Continuing improvements in the cost and power of laser diodes have been critical in launching the emerging fields of power over fiber (PoF), and laser power beaming. Laser power is transmitted either over fiber (for PoF), or through free space (power beaming), and is converted to electricity by photovoltaic cells designed to efficiently convert the laser light. MH GoPower's vertical multi-junction (VMJ) PV cell, designed for high intensity photovoltaic applications, is fueling the emergence of this market, by enabling unparalleled photovoltaic receiver flexibility in voltage, cell size, and power output. Our research examined the use of the VMJ PV cell for laser power transmission applications. We fully characterized the performance of the VMJ PV cell under various laser conditions, including multiple near IR wavelengths and light intensities up to tens of watts per cm2. Results indicated VMJ PV cell efficiency over 40% for 9xx nm wavelengths, at laser power densities near 30 W/cm2. We also investigated the impact of the physical dimensions (length, width, and height) of the VMJ PV cell on its performance, showing similarly high performance across a wide range of cell dimensions. We then evaluated the VMJ PV cell performance within the power over fiber application, examining the cell's effectiveness in receiver packages that deliver target voltage, intensity, and power levels. By designing and characterizing multiple receivers, we illustrated techniques for packaging the VMJ PV cell for achieving high performance (> 30%), high power (> 185 W), and target voltages for power over fiber applications.

Proceedings of the workshop on opportunities for atomic physics using slow, highly-charged ions

Energy Technology Data Exchange (ETDEWEB)

1987-01-01

The study of atomic physics with highly-charged ions is an area of intense activity at the present time because of a convergence of theoretical interest and advances in experimental techniques. The purpose of the Argonne ''Workshop on Opportunities for Atomic Physics Using Slow, Highly-Charged Ions'' was to bring together atomic, nuclear, and accelerator physicists in order to identify what new facilities would be most useful for the atomic physics community. The program included discussion of existing once-through machines, advanced ion sources, recoil ion techniques, ion traps, and cooler rings. One of the topics of the Workshop was to discuss possible improvement to the ANL Tandem-Linac facility (ATLAS) to enhance the capability for slowing down ions after they are stripped to a high-charge state (the Accel/Decel technique). Another topic was the opportunity for atomic physics provided by the ECR ion source which is being built for the Uranium Upgrade of ATLAS. 18 analytics were prepared for the individual papers in this volume.

WALLTURB International Workshop

CERN Document Server

Jimenez, Javier; Marusic, Ivan

2011-01-01

This book brings together selected contributions from the WALLTURB workshop on ”Understanding and modelling of wall turbulence” held in Lille, France, on April 21st to 23rd 2009. This workshop was organized by the WALLTURB consortium, in order to present to the relevant scientific community the main results of the project and to stimulate scientific discussions around the subject of wall turbulence. The workshop reviewed the recent progress in theoretical, experimental and numerical approaches to wall turbulence. The problems of zero pressure gradient, adverse pressure gradient and separating turbulent boundary layers were addressed in detail with the three approaches, using the most advanced tools. This book is a milestone in the research field, thanks to the high level of the invited speakers and the involvement of the contributors and a testimony of the achievement of the WALLTURB project.

Foreseeing techniques and control of emissions in thermal power plants. Workshop Latin American. [Selected Papers]; Control y tecnicas de prevision de las emisiones de centrales termoelectricas

Energy Technology Data Exchange (ETDEWEB)

Saldana, R; Morales, F; Urrutia, M [eds.; Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1997-12-31

This document contains the conference proceedings of the Latin-American Workshop ``Control and Prevision Techniques of Emissions in Power Plants`` carried out in Cuernavaca, Mexico on June 1996, with the participation of representatives of Argentina, Chile, Guatemala, Colombia, Ecuador, Mexico, Nicaragua, Panama and Venezuela, as well as specialists from the European Union. The core issue analyzed in this workshop was the control and the evaluation techniques of polluting emissions in Power Plants [Espanol] Este documento contiene las memorias de conferencia del Taller Latinoamericano ``Control y tecnicas de prevision de las emisiones de centrales termoelectricas`` que se llevo a cabo en Cuernavaca, Mexico en junio de 1996. Participaron representantes de Argentina, Chile, Guatemala, Colombia, Ecuador, Mexico, Nicaragua, Panama y Venezuela, asi como especialistas de la Union Europea. El tema central tratado en este taller fue el control y tecnicas de evaluacion de las emisiones contaminantes en centrales termoelectricas

Foreseeing techniques and control of emissions in thermal power plants. Workshop Latin American. [Selected Papers]; Control y tecnicas de prevision de las emisiones de centrales termoelectricas

Energy Technology Data Exchange (ETDEWEB)

Saldana, R.; Morales, F.; Urrutia, M. [eds.] [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1996-12-31

This document contains the conference proceedings of the Latin-American Workshop ``Control and Prevision Techniques of Emissions in Power Plants`` carried out in Cuernavaca, Mexico on June 1996, with the participation of representatives of Argentina, Chile, Guatemala, Colombia, Ecuador, Mexico, Nicaragua, Panama and Venezuela, as well as specialists from the European Union. The core issue analyzed in this workshop was the control and the evaluation techniques of polluting emissions in Power Plants [Espanol] Este documento contiene las memorias de conferencia del Taller Latinoamericano ``Control y tecnicas de prevision de las emisiones de centrales termoelectricas`` que se llevo a cabo en Cuernavaca, Mexico en junio de 1996. Participaron representantes de Argentina, Chile, Guatemala, Colombia, Ecuador, Mexico, Nicaragua, Panama y Venezuela, asi como especialistas de la Union Europea. El tema central tratado en este taller fue el control y tecnicas de evaluacion de las emisiones contaminantes en centrales termoelectricas

Workshops som forskningsmetode

OpenAIRE

Ørngreen, Rikke; Levinsen, Karin Tweddell

2017-01-01

This paper contributes to knowledge on workshops as a research methodology, and specifically on how such workshops pertain to e-learning. A literature review illustrated that workshops are discussed according to three different perspectives: workshops as a means, workshops as practice, and workshops as a research methodology. Focusing primarily on the latter, this paper presents five studies on upper secondary and higher education teachers’ professional development and on teaching and learnin...

Lightweight Damage Tolerant, High-Temperature Radiators for Nuclear Power and Propulsion

Science.gov (United States)

Craven, Paul D.; SanSoucie, Michael P.

2015-01-01

NASA is increasingly emphasizing exploration to bodies beyond near-Earth orbit. New propulsion systems and new spacecraft are being built for these missions. As the target bodies get further out from Earth, high energy density systems, e.g., nuclear fusion, for propulsion and power will be advantageous. The mass and size of these systems, including supporting systems such as the heat exchange system, including thermal radiators, will need to be as small as possible. Conventional heat exchange systems are a significant portion of the total thermal management mass and size. Nuclear electric propulsion (NEP) is a promising option for high-speed, in-space travel due to the high energy density of nuclear fission power sources and efficient electric thrusters. Heat from the reactor is converted to power for use in propulsion or for system power. The heat not used in the power conversion is then radiated to space as shown in figure 1. Advanced power conversion technologies will require high operating temperatures and would benefit from lightweight radiator materials. Radiator performance dictates power output for nuclear electric propulsion systems. Pitch-based carbon fiber materials have the potential to offer significant improvements in operating temperature, thermal conductivity, and mass. These properties combine to allow significant decreases in the total mass of the radiators and significant increases in the operating temperature of the fins. A Center-funded project at NASA Marshall Space Flight Center has shown that high thermal conductivity, woven carbon fiber fins with no matrix material, can be used to dissipate waste heat from NEP systems and because of high specific power (kW/kg), will require less mass and possibly less total area than standard metal and composite radiator fins for radiating the same amount of heat. This project uses an innovative approach to reduce the mass and size required for the thermal radiators to the point that in-space NEP and power

Power supply and ethics

International Nuclear Information System (INIS)

Anon.

2004-01-01

The 'Power Supply and Ethics' workshop was designed on the basis of a recommendation by the Nuclear Technology Committee (FA-KT) of VDI-GET. The topic is part of a series of events and publications by VDI in an area where engineering and the humanities converge. The Workshop comprised presentations and thorough discussions of seven papers on 'Power Supply and Ethics', reflecting a variety of contents and points of view of the different disciplines participating. The Workshop offered another opportunity to take the initiative and influence the public, especially politics. Other activities are planned which also the participants increasingly consider an obligation to the public. (orig.) [de

Photovoltaic-wind hybrid systems for remote power supply. Workshop. [Selected Papers

Energy Technology Data Exchange (ETDEWEB)

Huacuz, J. M.; Urrutia, M. [eds.] [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1997-12-31

This document include the papers of the RIER Workshop that was hold in Cancun, Mexico, on 21-25 April 1997. This Workshop was organized by the Non-Conventional Energy Unit of the Electrical Research Institute of Mexico (IIE), with the financial contributions from the Mexican National Council for Science and Technology (CONACYT) and the Iberoamerican Network for Rural Electrification with Renewable Energy (RIER) of the Program Science and Technology for Development (CYTED). The purpose of this Workshop was to present works developed on the technology of Photovoltaic-Wind Hybrid Systems, and to discuss both technical and non-technical factors that could foster or inhibit the widespread application this technology [Espanol] Este documento incluye los articulos tecnicos del taller de trabajo RIER, realizado en Cancun, Mexico, del 21 al 25 de abril de 1997. Este taller de trabajo fue organizado por el Instituto de Investigaciones Electricas (IIE), con la contribucion financiera del Consejo Nacional de Ciencia y Tecnologia (CONACYT) y de la Red de Trabajo Iberoamericana para la Electrificacion Rural con Energia Renovable (RIER) del programa Ciencia y Tecnologia para el Desarrollo (CYTED). El proposito de este taller fue presentar trabajos desarrollados sobre la tecnologia de sistemas hibridos fotovoltaicos y de viento, y discutir los factores tecnicos y no tecnicos que pudieran fomentar o detener la amplia aplicacion de esta tecnologia

Photovoltaic-wind hybrid systems for remote power supply. Workshop. [Selected Papers

Energy Technology Data Exchange (ETDEWEB)

Huacuz, J M; Urrutia, M [eds.; Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1998-12-31

This document include the papers of the RIER Workshop that was hold in Cancun, Mexico, on 21-25 April 1997. This Workshop was organized by the Non-Conventional Energy Unit of the Electrical Research Institute of Mexico (IIE), with the financial contributions from the Mexican National Council for Science and Technology (CONACYT) and the Iberoamerican Network for Rural Electrification with Renewable Energy (RIER) of the Program Science and Technology for Development (CYTED). The purpose of this Workshop was to present works developed on the technology of Photovoltaic-Wind Hybrid Systems, and to discuss both technical and non-technical factors that could foster or inhibit the widespread application this technology [Espanol] Este documento incluye los articulos tecnicos del taller de trabajo RIER, realizado en Cancun, Mexico, del 21 al 25 de abril de 1997. Este taller de trabajo fue organizado por el Instituto de Investigaciones Electricas (IIE), con la contribucion financiera del Consejo Nacional de Ciencia y Tecnologia (CONACYT) y de la Red de Trabajo Iberoamericana para la Electrificacion Rural con Energia Renovable (RIER) del programa Ciencia y Tecnologia para el Desarrollo (CYTED). El proposito de este taller fue presentar trabajos desarrollados sobre la tecnologia de sistemas hibridos fotovoltaicos y de viento, y discutir los factores tecnicos y no tecnicos que pudieran fomentar o detener la amplia aplicacion de esta tecnologia

Critical utopian action research and the power of future creating workshops

DEFF Research Database (Denmark)

Husted, Mia; Tofteng, Ditte Maria Børglum

in a participatory process of democratic development of everyday life. Critical utopian action research is characterized by a methodological preference to the future creating workshop as a method that captures the scientific theoretical approach: The future creating workshop outline a specific method originally...... in upturned-participation. Within traditional participatory planning we talk about a participatory ladder. The steps on the ladder reflects how one can participate in different scales an ways, from being merely an informant to being self-determining and performing. The ladder tells us notion about who...... of exploring, developing and analyzing is a common project between the participant and the researchers. Conclusions: When stressing critique and utopian ideas within upturned participatory processes as the starting point, the CUAR tradition brings new input to the wider society of action research, insisting...

Collider workshop

International Nuclear Information System (INIS)

Anon.

1982-01-01

The promise of initial results after the start of operations at CERN's SPS proton-antiproton collider and the prospects for high energy hadron collisions at Fermilab (Tevatron) and Brookhaven (ISABELLE) provided a timely impetus for the recent Topical Workshop on Forward Collider Physics', held at Madison, Wisconsin, from 10-12 December. It became the second such workshop to be held, the first having been in 1979 at the College de France, Paris. The 100 or so participants had the chance to hear preliminary results from the UA1, UA4 and UA5 experiments at the CERN SPS collider, together with other new data, including that from proton-antiproton runs at the CERN Intersecting Storage Rings

Reactor simulator development. Workshop material

International Nuclear Information System (INIS)

2001-01-01

The International Atomic Energy Agency (IAEA) has established a programme in nuclear reactor simulation computer programs to assist its Member States in education and training. The objective is to provide, for a variety of advanced reactor types, insight and practice in reactor operational characteristics and their response to perturbations and accident situations. To achieve this, the IAEA arranges for the supply or development of simulation programs and training material, sponsors training courses and workshops, and distributes documentation and computer programs. This publication consists of course material for workshops on development of such reactor simulators. Participants in the workshops are provided with instruction and practice in the development of reactor simulation computer codes using a model development system that assembles integrated codes from a selection of pre-programmed and tested sub-components. This provides insight and understanding into the construction and assumptions of the codes that model the design and operational characteristics of various power reactor systems. The main objective is to demonstrate simple nuclear reactor dynamics with hands-on simulation experience. Using one of the modular development systems, CASSIM tm , a simple point kinetic reactor model is developed, followed by a model that simulates the Xenon/Iodine concentration on changes in reactor power. Lastly, an absorber and adjuster control rod, and a liquid zone model are developed to control reactivity. The built model is used to demonstrate reactor behavior in sub-critical, critical and supercritical states, and to observe the impact of malfunctions of various reactivity control mechanisms on reactor dynamics. Using a PHWR simulator, participants practice typical procedures for a reactor startup and approach to criticality. This workshop material consists of an introduction to systems used for developing reactor simulators, an overview of the dynamic simulation

When power does not corrupt: superior individuation processes among powerful perceivers.

Science.gov (United States)

Overbeck, J R; Park, B

2001-10-01

To examine whether powerful people fail to individuate the less powerful, the authors assigned participants to either a high-power or low-power role for a computer E-mail role play. In 3 studies, participants in the high-power role made decisions and determined the outcomes of interactions; low-power role players had no power and relied on high-power targets for outcome decisions. Studies I and 2 found that high-power perceivers better individuated low-power targets. Study 3 demonstrated that high-power role players' superior judgment can be impaired by including a task that directs their responsibility toward organizational rather than interpersonal concerns. In all, results suggest that the effect of power on social judgment may be more complex and multifaceted than has previously been acknowledged.

Report from the 2nd Workshop on Extremely Large Databases

Directory of Open Access Journals (Sweden)

Jacek Becla

2009-03-01

Full Text Available The complexity and sophistication of large scale analytics in science and industry have advanced dramatically in recent years. Analysts are struggling to use complex techniques such as time series analysis and classification algorithms because their familiar, powerful tools are not scalable and cannot effectively use scalable database systems. The 2nd Extremely Large Databases (XLDB workshop was organized to understand these issues, examine their implications, and brainstorm possible solutions. The design of a new open source science database, SciDB that emerged from the first workshop in this series was also debated. This paper is the final report of the discussions and activities at this workshop.

Materials Innovation for Next-Generation T&D Grid Components. Workshop Summary Report

Energy Technology Data Exchange (ETDEWEB)

Taylor, Emmanuel [Energetics Incorporated, Columbia, MD (United States); Kramer, Caroline [Energetics Incorporated, Columbia, MD (United States); Marchionini, Brian [Energetics Incorporated, Columbia, MD (United States); Sabouni, Ridah [Energetics Incorporated, Columbia, MD (United States); Cheung, Kerry [U.S. Department of Energy (DOE), Washington, DC (United States). Office of Electricity Delivery and Energy Reliability (OE); Lee, Dominic F [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-10-01

The Materials Innovations for Next-Generation T&D Grid Components Workshop was co-sponsored by the U.S. Department of Energy (DOE) Office of Electricity Delivery and Energy Reliability and the Oak Ridge National Laboratory (ORNL) and held on August 26 27, 2015, at the ORNL campus in Oak Ridge, Tennessee. The workshop was planned and executed under the direction of workshop co-chair Dr. Kerry Cheung (DOE) and co-chair Dr. Dominic Lee (ORNL). The information contained herein is based on the results of the workshop, which was attended by nearly 50 experts from government, industry, and academia. The research needs and pathways described in this report reflect the expert opinions of workshop participants, but they are not intended to represent the views of the entire electric power community.

Switched power workshop power supply working group

International Nuclear Information System (INIS)

Haseroth, H.; Hopkins, D.; Ikezi, H.; Kirbie, H.; Lincke, E.; Wilson, M.

1988-01-01

The power supply working group was assigned the problem of pulse charging the 3-MeV gun. The gun is a radial line structure that has two charging configurations: a single ring charged to 500 kV or nine rings charged from 100 to 200 kV. In either configuration, the pulsed source must rapidly charge the structure's ring(s) before breakdown can begin. The issues encountered in charging the structure can be divided into two categories. First, the charging system must be well matched to the gun structure. Proper impedance matching will avoid reflections and limit the fault current if the ring should spark. Second, several systems can achieve the wide range of charge voltages necessary. Some are better suited to high voltages, while others are better at low voltages. The following paragraphs will address the impedance matching issues are review three choices for pulse generators. A system for each type of source is described along with a very rough cost estimate. 1 ref., 4 figs., 2 tabs

Switched power workshop: Power supply working group

International Nuclear Information System (INIS)

Haseroth, H.; Hopkins, D.; Ikezi, H.; Kirbie, H.C.; Lincke, E.; Wilson, M.

1989-01-01

The power supply working group was assigned the problem of pulse charging the 3-MeV gun. The gun is a radial line structure that has two charging configurations: a single ring charged to 500 kV or nine rings charged from 100 to 200 kV. In either configuration, the pulsed source must rapidly charge the structure's ring(s) before breakdown can begin. The issues encountered in charging the structure can be divided into two categories. First, the charging system must be well matched to the gun structure. Proper impedance matching will avoid reflections and limit the fault current if the ring should spark. Second, several systems can achieve the wide range of charge voltages necessary. Some are better suited to high voltages, while others are better at low voltages. The following paragraphs will address the impedance matching issues and review three choices for pulse generators. A system for each type of source is described along with a very rough cost estimate. 1 ref., 4 figs., 2 tabs

High power klystrons for efficient reliable high power amplifiers

Science.gov (United States)

Levin, M.

1980-11-01

This report covers the design of reliable high efficiency, high power klystrons which may be used in both existing and proposed troposcatter radio systems. High Power (10 kW) klystron designs were generated in C-band (4.4 GHz to 5.0 GHz), S-band (2.5 GHz to 2.7 GHz), and L-band or UHF frequencies (755 MHz to 985 MHz). The tubes were designed for power supply compatibility and use with a vapor/liquid phase heat exchanger. Four (4) S-band tubes were developed in the course of this program along with two (2) matching focusing solenoids and two (2) heat exchangers. These tubes use five (5) tuners with counters which are attached to the focusing solenoids. A reliability mathematical model of the tube and heat exchanger system was also generated.

WORKSHOP: Let's twist again..

Energy Technology Data Exchange (ETDEWEB)

Villalobos Baillie, Orlando

1988-12-15

In the quantum chromodynamics (QCD) candidate theory of interquark forces, calculations involve summing the effects from many different possible quark/gluon interactions. In addition to the 'leading term' frequently used as the basis for QCD calculations, additional contributions — so-called 'higher twists' — are modulated by powers of kinematical factors. An illuminating international workshop to discuss higher twist QCD was held at the College de France, Paris, from 21-23 September.

Power to Production: Activity Guide.

Science.gov (United States)

Massachusetts Univ., Lowell. Tsongas Industrial History Center.

This field trip program consists of a 90-minute interpretive tour and a 90-minute hands-on workshop. The tour and workshop explore the role of water power in the Industrial Revolution. On the tour, students discover firsthand the unique resources of Lowell, Massachusetts, and the Park, while the workshop brings these historic resources to life as…

Building Capacity for Data-Driven Decision Making in African HIV Testing Programs: Field Perspectives on Data Use Workshops.

Science.gov (United States)

Courtenay-Quirk, Cari; Spindler, Hilary; Leidich, Aimee; Bachanas, Pam

2016-12-01

Strategic, high quality HIV testing services (HTS) delivery is an essential step towards reaching the end of AIDS by 2030. We conducted HTS Data Use workshops in five African countries to increase data use for strategic program decision-making. Feedback was collected on the extent to which workshop skills and tools were applied in practice and to identify future capacity-building needs. We later conducted six semistructured phone interviews with workshop planning teams and sent a web-based survey to 92 past participants. The HTS Data Use workshops provided accessible tools that were readily learned by most respondents. While most respondents reported increased confidence in interpreting data and frequency of using such tools over time, planning team representatives indicated ongoing needs for more automated tools that can function across data systems. To achieve ambitious global HIV/AIDS targets, national decision makers may continue to seek tools and skill-building opportunities to monitor programs and identify opportunities to refine strategies.

Proceedings of the workshop on formation of supermolecular structures in composite fluid

International Nuclear Information System (INIS)

Tanaka, Fumihiko; Ohta, Takao; Ikeda, Hironobu

1992-10-01

This is the report of the titled workshop held at the National Laboratory for High Energy Physics on July 2 and 3, 1992. This workshop was planned as a part of the research project on the utilization of booster neutrons in this Laboratory, and is one of the attempts to apply the technique of neutron scattering with wide visual field. Composite liquid means the solution that has the capability of forming the structure in 10-1000 nm and contains polymers, liquid crystals, micelles or films inside. The hierarchy of the concept of supermolecules, the flexibility of the form of particles, multiple composition mixture system and so on are the subjects in this field. In the workshop of this time, the themes were limited to three phenomena, that is, the formation of networks, microscopic phase separation and mesophase, and solvation and the formation of micelles. The measurement of neutron scattering by label method offers a powerful means hereafter for elucidating the structure and the dynamics of supermolecular liquid. (K.I.)

A target group-specific approach to ''green'' power retailing: students as consumers of renewable energy

International Nuclear Information System (INIS)

Gossling, S.; Kunkel, T.; Schumacher, K.; Heck, N.; Birkemeyer, J.; Froese, J.; Naber, N.; Schliermann, E.

2005-01-01

An extensive body of literature exists on the obstacles that have to be overcome in green power retailing. In this article, target group-specific marketing is evaluated as a strategy to increase the share of residential customers of green power. A sample of students in the city of Freiburg, Germany was interviewed in order to assess their awareness of environmental issues, their willingness to change to green power products, and to better understand individual hindrances in changing the power supplier. The analysis shows that students are highly positive towards green power products, but for several reasons difficult to reach in marketing campaigns. Aspects to be considered in addressing this consumer-group include the students' particular expectations towards green products, their living-conditions, price sensitivity, and their perception of the relative effort involved in changing the power provider. (author)

Efficient visualization of high-throughput targeted proteomics experiments: TAPIR.

Science.gov (United States)

Röst, Hannes L; Rosenberger, George; Aebersold, Ruedi; Malmström, Lars

2015-07-15

Targeted mass spectrometry comprises a set of powerful methods to obtain accurate and consistent protein quantification in complex samples. To fully exploit these techniques, a cross-platform and open-source software stack based on standardized data exchange formats is required. We present TAPIR, a fast and efficient Python visualization software for chromatograms and peaks identified in targeted proteomics experiments. The input formats are open, community-driven standardized data formats (mzML for raw data storage and TraML encoding the hierarchical relationships between transitions, peptides and proteins). TAPIR is scalable to proteome-wide targeted proteomics studies (as enabled by SWATH-MS), allowing researchers to visualize high-throughput datasets. The framework integrates well with existing automated analysis pipelines and can be extended beyond targeted proteomics to other types of analyses. TAPIR is available for all computing platforms under the 3-clause BSD license at https://github.com/msproteomicstools/msproteomicstools. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

76 FR 72203 - Voltage Coordination on High Voltage Grids; Notice of Reliability Workshop Agenda

Science.gov (United States)

2011-11-22

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. AD12-5-000] Voltage Coordination on High Voltage Grids; Notice of Reliability Workshop Agenda As announced in the Notice of Staff..., from 9 a.m. to 4:30 p.m. to explore the interaction between voltage control, reliability, and economic...

NASA Kennedy Space Center Educator Workshops: Exploring Their Impact on Teacher Attitudes and Concerns

Science.gov (United States)

Dreschel, Thomas W.

1996-01-01

The National Aeronautics and Space Administration holds summer teacher workshops to motivate teachers to use space science in their lessons. In evaluating these workshops, the areas of interest were participant beliefs about science and science teaching and concerns about educational change and innovation. The teachers attending workshops in 1995, past participants, teachers that received materials but had not attended a workshop, and science researchers were surveyed using the Beliefs about Science and Science Education Survey and/or the Stages of Concern Questionnaire. Comparisons were made by workshop length, time since workshop, and highest grade taught. Reductions in concerns were most evident in the four week workshop. Changes in beliefs were also observed relative to teaching approach and ability. Differences in beliefs were observed between teachers and science researchers. Differences were also observed relative to time since attendance and by grade level taught. It is recommended that the workshops be at least four weeks in length and in length and target specific grade levels, that refresher workshops be offered.

Working Group summary reports from the Advanced Photon Source reliability workshop

International Nuclear Information System (INIS)

1992-05-01

A workshop was held at APS to address reliability goals for accelerator systems. Seventy-one individuals participated in the workshop, including 30 from other institutions. The goals of the workshop were to: (1) Give attendees an introduction to the basic concepts of reliability analysis. (2) Exchange information on operating experience at existing accelerator facilities and strategies for achieving reliability at facilities under design or in construction. (3) Discuss reliability goals for APS and the means of their achievement. This report contains the working group summary report an APS's following systems: RF Systems; Power Supplies; Magnet Systems; Interlock and Diagnostics; and Vacuum Systems

2. International workshop on spallation materials technology

International Nuclear Information System (INIS)

Carsughi, F.; Mansur, L.K.; Sommer, W.F.; Ullmaier, H.

1997-11-01

This document contains 25 papers consisting an abstract prepared by the authors, followed by copies of the presentation viewgraphs used by speakers. The topics were: Target options for SINQ; Overview of the NSNS target system; ISIS target and moderator materials; Trispal project; JHF N-ARENA; Design, load conditions and manufacturing aspect of the ESS MERCURY TARGET unit; Radiation damage simulatiion to measure recoil spectra distribution; Radiation damage calculation to spallation neutron source materials; Hadron-induced neutron production in Pb and U targets from 1-5 GeV; Proton beam effects on W rods, surface cooled by water; Corrosion and fatigue behavior of metals and alloys in high radiation fields; compability of materials with mercury for NSNS target system; Research activities at PSI on structural materials for spallation neutron source; The accelerator production of tritium materials reserach program and Los Alamos National Laboratory; Experimental program on irradiation effects in structural materials of the Trispal project; First pulsed power materials test at Livermore; Plan of thermal shock fracture test at JAERI; Is there a hydrogen problem in target materials in high-power spatllation source?; Materials consideration for the NSNS target; Materials durability issures in spallation neutron source applications; Post-irradiation investigations at the FZJ; Microstructure and hardening of steels containing high helium concentrations; Tensile properties and microstructure of the F82H ferritic-martensitic steel after irradiation in the PIREX facility

High-resolution wavefront control of high-power laser systems

International Nuclear Information System (INIS)

Brase, J.; Brown, C.; Carrano, C.; Kartz, M.; Olivier, S.; Pennington, D.; Silva, D.

1999-01-01

Nearly every new large-scale laser system application at LLNL has requirements for beam control which exceed the current level of available technology. For applications such as inertial confinement fusion, laser isotope separation, laser machining, and laser the ability to transport significant power to a target while maintaining good beam quality is critical. There are many ways that laser wavefront quality can be degraded. Thermal effects due to the interaction of high-power laser or pump light with the internal optical components or with the ambient gas are common causes of wavefront degradation. For many years, adaptive optics based on thing deformable glass mirrors with piezoelectric or electrostrictive actuators have be used to remove the low-order wavefront errors from high-power laser systems. These adaptive optics systems have successfully improved laser beam quality, but have also generally revealed additional high-spatial-frequency errors, both because the low-order errors have been reduced and because deformable mirrors have often introduced some high-spatial-frequency components due to manufacturing errors. Many current and emerging laser applications fall into the high-resolution category where there is an increased need for the correction of high spatial frequency aberrations which requires correctors with thousands of degrees of freedom. The largest Deformable Mirrors currently available have less than one thousand degrees of freedom at a cost of approximately $1M. A deformable mirror capable of meeting these high spatial resolution requirements would be cost prohibitive. Therefore a new approach using a different wavefront control technology is needed. One new wavefront control approach is the use of liquid-crystal (LC) spatial light modulator (SLM) technology for the controlling the phase of linearly polarized light. Current LC SLM technology provides high-spatial-resolution wavefront control, with hundreds of thousands of degrees of freedom, more

Stopping power of antiprotons in H, H₂, and He targets

DEFF Research Database (Denmark)

Lühr, Armin Christian; Saenz, Alejandro

2009-01-01

The stopping power of antiprotons in atomic and molecular hydrogen as well as helium was calculated in an impact-energy range from 1 keV to 6.4 MeV. In the case of H2 and He the targets were described with a single-active electron model centered on the target. The collision process was treated...... of the corrections to the first-order stopping number, the average energy transferred to the target electrons, and the relative importance of the excitation and the ionization process for the energy loss of the projectile was determined. Finally, the stopping powers of the H, H2, and He targets were directly...

Physics beyond Colliders Kickoff Workshop

CERN Document Server

2016-01-01

The aim of the workshop is to explore the opportunities offered by the CERN accelerator complex and infrastructure to get new insights into some of today's outstanding questions in particle physics through projects complementary to high-energy colliders and other initiatives in the world. The focus is on fundamental physics questions that are similar in spirit to those addressed by high-energy colliders, but that may require different types of experiments. The kickoff workshop is intended to stimulate new ideas for such projects, for which we encourage the submission of abstracts.

Workshop on Physics Beyond Colliders

CERN Document Server

2016-01-01

The aim of the workshop is to explore the opportunities offered by the CERN accelerator complex and infrastructure to get new insights into some of today's outstanding questions in particle physics through projects complementary to high-energy colliders and other initiatives in the world. The focus is on fundamental physics questions that are similar in spirit to those addressed by high-energy colliders, but that may require different types of experiments. The kick-off workshop is intended to stimulate new ideas for such projects, for which we encourage the submission of abstracts.

Electric discharge machining device for laboratories and workshops

International Nuclear Information System (INIS)

Lanxner, M.; Berko, A.; Ron, N.

1976-11-01

A simple low power electric discharge machining (EDM) device for special uses in laboratories and workshops is presented. The device includes an RC generator, an electromechanical servo 3-axis work-tool alignment system and a closed dielectric fluid circulation loop

NATO Advanced Research Workshop on Frontiers of High-Pressure Research

CERN Document Server

Etters, Richard

1991-01-01

The role of high pressure experiments in the discovery of supercon­ ducting materials with a T. above liquid nitrogen temperature has demon­ strated the importance of such experiments. The same role holds true in the tailoring of materials for optoelectronic devices. In addition, much progress has been made recently in the search for metallic hydro­ gen, and the application of high pressure in polymer research has brought forth interesting results. These facts together with the suc­ cess of previous small size meetings (such as the "First International Conference on the Physics of Solids at High Pressure", held in 1965 in Tucson, Arizona, U. S. A. ; "High Pressure and Low Temperature Physics", held in 1977 in Cleveland, Ohio, U. S. A. ; and "Physics of Solids Under High Pressure", held in 1981 in bad Honnef, Germany), motivated us to organize a workshop with emphasis on the newest results and trends in these fields of high pressure research. Furthermore, it was intended to mix experienced and young scien�...

Fast optical shutters for Nova, a high power fusion laser

International Nuclear Information System (INIS)

Bradley, L.P.; Gagnon, W.L.; Carder, B.M.

1977-01-01

Preliminary design and performance test results for fast optical shutters intended for use in the Nova high power fusion laser system are briefly described. Both an opening shutter to protect the pellet target from amplified spontaneous emission (ASE), and a closing shutter to protect the laser from light reflected back from the target are discussed. Faraday rotators, synchronized by a 400 Hz oscillator, provide an opening shutter mechanism with an opening time of approximately 10 μs. A plasma closing shutter, employing electrical sublimation of a foil, provide a shutter closing time of 70 ns +- 20 ns. Energy for foil sublimation is provided by discharge of a 42 J capacitor bank. Implementation of these shutter techniques in the Nova system is anticipated to improve laser output power and efficiency

Statement at TM/workshop on evaluation methodology for national nuclear infrastructure development, 10 December 2008, Vienna, Austria

International Nuclear Information System (INIS)

Sokolov, Y.

2008-01-01

In his statement at the Technical Meeting Workshop on Evaluation Methodology for National Nuclear Infrastructure Development Mr. Yuri Sokolov, IAEA Deputy Director General, Head of the Department of Nuclear Energy, thanked the co-sponsors of the workshop, namely Canada, China, France, India, Japan, the Republic of Korea, the Russian Federation and the United States for their continued support and the Nuclear Power Engineering Section for their dedication and hard work to implement this workshop. The evaluation methodology that is the main subject of this workshop is a component of building infrastructure for the implementation of cost-effective, safe and secure nuclear power programme. It aims to provide a tool for effective planning. The IAEA evaluation approach can be used either by a Member State wishing to review its own progress (self-assessment) or as a basis for an external review through which a Member State wishes to reassure others that its nuclear programme is effective. The IAEA can, upon a request from the Member State, provide Integrated Nuclear Infrastructure Review missions, INIR, conducted by international experts. These INIR missions provide a means for countries to work with the IAEA in an open and transparent way to ensure they are taking a comprehensive and integrated approach to nuclear power as promoted in the Milestones document. National self-assessments supported by INIR missions will help Member States to identify gaps and areas that need increased attention, and will help the Agency to focus the assistance on the Member States needs. Another theme of the workshop is the role of the Nuclear Energy Programme Implementing Organization (NEPIO), in studying the nuclear power option and coordinating planning among various stakeholders. During the workshop publications in preparation will be presented including one on responsibilities and capabilities of owner-operator organizations and one on workforce planning. Presentations from the

Proceedings of the 2010 renewable energy infrastructure workshop

International Nuclear Information System (INIS)

2010-01-01

This workshop provided a forum for electric power industry leaders and key stakeholders to discuss Canada's renewable energy infrastructure needs. The workshop was held to provide practical solutions for meeting the increased demand for renewable energy as well as to offer a range of marketplace options and funding opportunities. Participants in the workshop examined the regulatory framework of the Green Energy Act and its potential impact on organizations. Approval process procedures for renewable energy projects were reviewed, and methods of ensuring the integration of renewable energy projects with current business strategies were discussed. Communications strategies for managing the public perception of energy project were presented. Policy barriers to infrastructure development were outlined. Methods of developing partnerships with Aboriginal communities were also discussed. The conference featured 16 presentations, of which 3 have been catalogued separately for inclusion in this database. tabs., figs.

High-power klystrons

Science.gov (United States)

Siambis, John G.; True, Richard B.; Symons, R. S.

1994-05-01

Novel emerging applications in advanced linear collider accelerators, ionospheric and atmospheric sensing and modification and a wide spectrum of industrial processing applications, have resulted in microwave tube requirements that call for further development of high power klystrons in the range from S-band to X-band. In the present paper we review recent progress in high power klystron development and discuss some of the issues and scaling laws for successful design. We also discuss recent progress in electron guns with potential grading electrodes for high voltage with short and long pulse operation via computer simulations obtained from the code DEMEOS, as well as preliminary experimental results. We present designs for high power beam collectors.

Climate change and local policy. Report of the workshop 2 December 1998, KIT, Amsterdam

International Nuclear Information System (INIS)

Schol, E.; Van Vuuren, V.C.; Burger, H.

1999-01-01

The objective of the title workshop was to exchange knowledge among Dutch experts and local policy makers on the possibilities for cities to reduce their CO 2 -emissions. The workshop was subdivided into three working groups: (1) Monitoring and Benchmarking; (2) Liberalization of the Energy Market; and (3) Mobilization of the Target Groups

Deuterium high pressure target

International Nuclear Information System (INIS)

Perevozchikov, V.V.; Yukhimchuk, A.A.; Vinogradov, Yu.I.

2001-01-01

The design of the deuterium high-pressure target is presented. The target having volume of 76 cm 3 serves to provide the experimental research of muon catalyzed fusion reactions in ultra-pure deuterium in the temperature range 80-800 K under pressures of up to 150 MPa. The operation of the main systems of the target is described: generation and purification of deuterium gas, refrigeration, heating, evacuation, automated control system and data collection system

Switching power converters medium and high power

CERN Document Server

Neacsu, Dorin O

2013-01-01

An examination of all of the multidisciplinary aspects of medium- and high-power converter systems, including basic power electronics, digital control and hardware, sensors, analog preprocessing of signals, protection devices and fault management, and pulse-width-modulation (PWM) algorithms, Switching Power Converters: Medium and High Power, Second Edition discusses the actual use of industrial technology and its related subassemblies and components, covering facets of implementation otherwise overlooked by theoretical textbooks. The updated Second Edition contains many new figures, as well as

Proceedings of Japan-U.S. workshop P-196 on high heat flux components and plasma surface interactions for next devices

International Nuclear Information System (INIS)

Wilson, K.N.; Yamashina, T.

1993-03-01

The Japan-US Workshop P-196 was successfully carried out in Kyushu University, Chikushi Campus, from November 17 to 19. The major concern was on the research and development required both for international Thermonuclear Experimental Reactor (ITER) and Large Helical Device (LHD). Most of the discussion items was similar to that of the last workshop, e.g. PFC and PSI in Large Device, High Heat Flux Component, Laboratory Studies and Neutron Damage. The presentation number concerning High Heat Flux Component was largest. (J.P.N.)

Report on the international workshop on next generation linear colliders

International Nuclear Information System (INIS)

Ruth, R.D.

1989-05-01

Many laboratories around the world have begun vigorous research programs on a next generation linear collider (NLC). However, it has been recognized that the research towards NLC is beyond the capabilities of any one laboratory presently. This workshop was organized to begin a series of workshops that address this problem. Specifically, the main goals of the workshop were to discuss research programs of the various laboratories around the world, to identify common areas of interest in the various NLC designs, and finally to advance these programs by collaboration. The particular topics discussed briefly in this paper are: parameters, rf power, structures, final focus, beam dynamics, damping rings, and instrumentation. 2 refs., 3 figs., 6 tabs

Second ICFA workshop

International Nuclear Information System (INIS)

Anon.

1979-01-01

A summary is given of the topics discussed at the second ICFA Workshop on 'Possibilities and Limitations of Accelerators and Detectors'. High energy accelerators are discussed, particularly electron-positron and proton-antiproton colliders. (W.D.L.).

Splitting of high power, cw proton beams

Directory of Open Access Journals (Sweden)

Alberto Facco

2007-09-01

Full Text Available A simple method for splitting a high power, continuous wave (cw proton beam in two or more branches with low losses has been developed in the framework of the EURISOL (European Isotope Separation On-Line Radioactive Ion Beam Facility design study. The aim of the system is to deliver up to 4 MW of H^{-} beam to the main radioactive ion beam production target, and up to 100 kW of proton beams to three more targets, simultaneously. A three-step method is used, which includes magnetic neutralization of a fraction of the main H^{-} beam, magnetic splitting of H^{-} and H^{0}, and stripping of H^{0} to H^{+}. The method allows slow raising and individual fine adjustment of the beam intensity in each branch.

Proceedings of the international workshop on spallation materials technology

Energy Technology Data Exchange (ETDEWEB)

Mansur, L.K.; Ullmaier, H. [comps.