WorldWideScience

Sample records for high-power laser applications

  1. High-power optics lasers and applications

    CERN Document Server

    Apollonov, Victor V

    2015-01-01

    This book covers the basics, realization and materials for high power laser systems and high power radiation interaction with  matter. The physical and technical fundamentals of high intensity laser optics and adaptive optics and the related physical processes in high intensity laser systems are explained. A main question discussed is: What is power optics? In what way is it different from ordinary optics widely used in cameras, motion-picture projectors, i.e., for everyday use? An undesirable consequence of the thermal deformation of optical elements and surfaces was discovered during studies of the interaction with powerful incident laser radiation. The requirements to the fabrication, performance and quality of optical elements employed within systems for most practical applications are also covered. The high-power laser performance is generally governed by the following: (i) the absorption of incident optical radiation (governed primarily by various absorption mechanisms), (ii) followed by a temperature ...

  2. High Power Diode Lasers Technology and Applications

    CERN Document Server

    Bachmann, Friedrich; Poprawe, Reinhart

    2007-01-01

    In a very comprehensive way this book covers all aspects of high power diode laser technology for materials processing. Basics as well as new application oriented results obtained in a government funded national German research project are described in detail. Along the technological chain after a short introduction in the second chapter diode laser bar technology is discussed regarding structure, manufacturing technology and metrology. The third chapter illuminates all aspects of mounting and cooling, whereas chapter four gives wide spanning details on beam forming, beam guiding and beam combination, which are essential topics for incoherently coupled multi-emitter based high power diode lasers. Metrology, standards and safety aspects are the theme of chapter five. As an outcome of all the knowledge from chapter two to four various system configurations of high power diode lasers are described in chapter six; not only systems focussed on best available beam quality but especially also so called "modular" set...

  3. Innovations in high power fiber laser applications

    Science.gov (United States)

    Beyer, Eckhard; Mahrle, Achim; Lütke, Matthias; Standfuss, Jens; Brückner, Frank

    2012-02-01

    Diffraction-limited high power lasers represent a new generation of lasers for materials processing, characteristic traits of which are: smaller, cost-effective and processing "on the fly". Of utmost importance is the high beam quality of fiber lasers which enables us to reduce the size of the focusing head incl. scanning mirrors. The excellent beam quality of the fiber laser offers a lot of new applications. In the field of remote cutting and welding the beam quality is the key parameter. By reducing the size of the focusing head including the scanning mirrors we can reach scanning frequencies up to 1.5 kHz and in special configurations up to 4 kHz. By using these frequencies very thin and deep welding seams can be generated experienced so far with electron beam welding only. The excellent beam quality of the fiber laser offers a high potential for developing new applications from deep penetration welding to high speed cutting. Highly dynamic cutting systems with maximum speeds up to 300 m/min and accelerations up to 4 g reduce the cutting time for cutting complex 2D parts. However, due to the inertia of such systems the effective cutting speed is reduced in real applications. This is especially true if complex shapes or contours are cut. With the introduction of scanner-based remote cutting systems in the kilowatt range, the effective cutting speed on the contour can be dramatically increased. The presentation explains remote cutting of metal foils and sheets using high brightness single mode fiber lasers. The presentation will also show the effect of optical feedback during cutting and welding with the fiber laser, how those feedbacks could be reduced and how they have to be used to optimize the cutting or welding process.

  4. High power CO lasers and their application potential

    Science.gov (United States)

    Maisenhaelder, F.

    1989-06-01

    Industrial applications of high-power CO lasers are examined. The characteristics specific to CO lasers are briefly reviewed, and applications where the CO laser seems to promise wavelength-related advantages over other lasers are examined. Experimentally demonstrated applications in the drilling and cutting of metals, isotope separation and photochemistry, and laser medicine are addressed, Developments in the high power range in Japan, Soviet Union, and Germany are described, and a comparison is made between high power CO and CO2 gas lasers for civil applications.

  5. High Power Fiber Lasers and Applications to Manufacturing

    Science.gov (United States)

    Richardson, Martin; McComb, Timothy; Sudesh, Vikas

    2008-09-01

    We summarize recent developments in high power fiber laser technologies and discuss future trends, particularly in their current and future use in manufacturing technologies. We will also describe our current research programs in fiber laser development, ultra-fast and new lasers, and will mention the expectations in these areas for the new Townes Laser Institute. It will focus on new core laser technologies and their applications in medical technologies, advanced manufacturing technologies and defense applications. We will describe a program on large mode area fiber development that includes results with the new gain-guiding approach, as well as high power infra-red fiber lasers. We will review the opportunities for high power fiber lasers in various manufacturing technologies and illustrate this with applications we are pursuing in the areas of femtosecond laser applications, advanced lithographies, and mid-IR technologies.

  6. High-power lasers for directed-energy applications.

    Science.gov (United States)

    Sprangle, Phillip; Hafizi, Bahman; Ting, Antonio; Fischer, Richard

    2015-11-01

    In this article, we review and discuss the research programs at the Naval Research Laboratory (NRL) on high-power lasers for directed-energy (DE) applications in the atmosphere. Physical processes affecting propagation include absorption/scattering, turbulence, and thermal blooming. The power levels needed for DE applications require combining a number of lasers. In atmospheric turbulence, there is a maximum intensity that can be placed on a target that is independent of the initial beam spot size and laser beam quality. By combining a number of kW-class fiber lasers, scientists at the NRL have successfully demonstrated high-power laser propagation in a turbulent atmosphere and wireless recharging. In the NRL experiments, four incoherently combined fiber lasers having a total power of 5 kW were propagated to a target 3.2 km away. These successful high-power experiments in a realistic atmosphere formed the basis of the Navy's Laser Weapon System. We compare the propagation characteristics of coherently and incoherently combined beams without adaptive optics. There is little difference in the energy on target between coherently and incoherently combined laser beams for multi-km propagation ranges and moderate to high levels of turbulence. Unlike incoherent combining, coherent combining places severe constraints on the individual lasers. These include the requirement of narrow power spectral linewidths in order to have long coherence times as well as polarization alignment of all the lasers. These requirements are extremely difficult for high-power lasers.

  7. CHRONICLE: International forum on advanced high-power lasers and applications (AHPLA '99)

    Science.gov (United States)

    Afanas'ev, Yurii V.; Zavestovskaya, I. N.; Zvorykin, V. D.; Ionin, Andrei A.; Senatsky, Yu V.; Starodub, Aleksandr N.

    2000-05-01

    A review of reports made on the International Forum on Advanced High-Power Lasers and Applications, which was held at the beginning of November 1999 in Osaka (Japan), is presented. Five conferences were held during the forum on High-Power Laser Ablation, High-Power Lasers in Energy Engineering, High-Power Lasers in Civil Engineering and Architecture, High-Power Lasers in Manufacturing, and Advanced High-Power Lasers. The following trends in the field of high-power lasers and their applications were presented: laser fusion, laser applications in space, laser-triggered lightning, laser ablation of materials by short and ultrashort pulses, application of high-power lasers in manufacturing, application of high-power lasers in mining, laser decommissioning and decontamination of nuclear reactors, high-power solid-state and gas lasers, x-ray and free-electron lasers. One can find complete information on the forum in SPIE, vols. 3885-3889.

  8. High-power laser applications in Nippon Steel Corporation

    Science.gov (United States)

    Minamida, Katsuhiro

    2000-02-01

    The laser, which was invented in 1960, has been developed using various substances of solids, liquids, gases and semiconductors as laser active media. Applications of laser utilizing the coherent properties of laser light and the high power density light abound in many industries and in heavy industries respectively. The full-scale use of lasers in the steel industry began nearly 23 years ago with their applications as controllable light sources. Its contribution to the increase in efficiency and quality of the steel making process has been important and brought us the saving of the energy, the resource and the labor. Laser applications in the steel making process generally require high input energy, so it is essential to consider the interaction between the laser beam and the irradiated material. In particular, the reflectivity of the laser beam on the surface of material and the quantity of the laser-induced plasma are critical parameters for high efficient processes with low energy losses. We have developed plenty of new laser systems for the steel making process with their considerations in mind. A review of the following high-power-laser applications is given in the present paper: (1) Use of plasma as a secondary heat source in CO2 laser welding for connecting steel sheets of various grades. (2) Laser-assisted electric resistance welding of pipes. (3) New type all-laser-welded honeycomb panels for high-speed transport. (4) Laser flying welder for continuous hot rolling mill using two 45 kW CO2 lasers.

  9. High power fiber lasers

    Institute of Scientific and Technical Information of China (English)

    LOU Qi-hong; ZHOU Jun

    2007-01-01

    In this review article, the development of the double cladding optical fiber for high power fiber lasers is reviewed. The main technology for high power fiber lasers, including laser diode beam shaping, fiber laser pumping techniques, and amplification systems, are discussed in de-tail. 1050 W CW output and 133 W pulsed output are ob-tained in Shanghai Institute of Optics and Fine Mechanics, China. Finally, the applications of fiber lasers in industry are also reviewed.

  10. High power fiber delivery for laser ignition applications.

    Science.gov (United States)

    Yalin, Azer P

    2013-11-01

    The present contribution provides a concise review of high power fiber delivery research for laser ignition applications. The fiber delivery requirements are discussed in terms of exit energy, intensity, and beam quality. Past research using hollow core fibers, solid step-index fibers, and photonic crystal and bandgap fibers is summarized. Recent demonstrations of spark delivery using large clad step-index fibers and Kagome photonic bandgap fibers are highlighted.

  11. High-power diode lasers and their direct industrial applications

    Science.gov (United States)

    Loosen, Peter; Treusch, Hans-Georg; Haas, C. R.; Gardenier, U.; Weck, Manfred; Sinnhoff, V.; Kasperowski, S.; vor dem Esche, R.

    1995-04-01

    The paper summarizes activities of the two Fraunhofer-Institutes ILT and IPT concerning the development of high-power laser-diode stacks and their direct industrial applications. With microchannel coolers in copper technology and ultra-precision machined micro-optics a stack of 330 - 400 W total power with a maximum intensity of the focused beam of 2 104 W/cm2 has been built and tested in first applications. By further improvements of the lens-fabrication and -alignment technology as well as increase of the number of stacked diodes an output power in the kW-range and intensities up to about 105 W/cm2 shall be achieved in the near future. Applications of such laser sources in surface technology, in the processing of plastics, in laser-assisted machining and in brazing are discussed.

  12. Application of a high power laser to demilitarization problems

    Science.gov (United States)

    Lyman, O. R.

    1981-09-01

    Attempts to experimentally cut rocket motors, puncture agent cavities, and perform other operations associated with demilitarization of munitions with a high power CO2 laser are discussed. Laser requirements are outlined and problems associated with laser operations contiguous with hazardous materials are highlighted. It is concluded that while the use of a CO2 laser of about 10 kilowatts output has advantages for some demilitarization operations, it is not practical for many.

  13. Optimized high-power diode laser, laser arrays, and bars for pump applications

    Science.gov (United States)

    Hülsewede, R.; Schulze, H.; Sebastian, J.; Schröder, D.; Meusel, J.; Wolf, J.; Hennig, P.

    2009-02-01

    Broad area diode laser and diode laser bars are the most efficient light sources. In comparison to solid state laser or gas laser systems the over all beam quality of the diode laser is poor. Thus most application of diode laser bars is high efficient pumping of solid state lasers converting the beam quality and scaling the power of laser systems within the kW range. The pump efficiency and the beam coupling efficiency of the diode laser pumped systems has to be increased to meet the increasing laser market demands for reduced costs. JENOPTIK Diode Lab GmbH (JDL) has optimized their high power brilliance bars to enable reliable high power operation especially, for the 9xx nm wavelength range and low far field divergences. Superior reliability with long operation time of 13,000 hours and high power operation of 200 W are demonstrated for high power bars high filling factor mounted on passively cooled heat sinks. Smaller far field divergence at high power levels requires longer cavity length and higher efficiencies in the beam coupling needs requires lower filling factors. The new high brilliance bars and arrays with 20% filling factor are showing high power operation up to 95 W and a slow axis beam divergence of less than 8° (95% power content).

  14. High-power green diode laser systems for biomedical applications

    DEFF Research Database (Denmark)

    Müller, André

    Due to their unique characteristics, diode lasers are increasingly attractive for numerous applications. For example, in the biomedical field the provided output power, spatial quality, and wavelength coverage of diode lasers has enabled their applications in, e.g., dermatology, diffuse spectrosc......Due to their unique characteristics, diode lasers are increasingly attractive for numerous applications. For example, in the biomedical field the provided output power, spatial quality, and wavelength coverage of diode lasers has enabled their applications in, e.g., dermatology, diffuse......, the obtained results clearly strengthen the application potential of diode lasers, including the biomedical field....

  15. Application possibilities of plasmas generated by high power laser ablation

    OpenAIRE

    Torrisi, L.

    2009-01-01

    High-power pulsed lasers emitting IR and visible radiation with intensities ranging between 10^8 and 10^16 W/cm2, pulse duration from 0.4 to 9 ns and energy from 100 mJ up to 600 J, operating in single mode or in repetition rate, can be employed to produce non-equilibrium plasma in vacuum by irradiating solid targets. Such a laser-produced plasma generates highly charged and high-energy ions of various elements, as well as soft and hard X-ray radiations. Heavy ions with charge state up to 58+...

  16. Application and the key technology on high power fiber-optic laser in laser weapon

    Science.gov (United States)

    Qu, Zhou; Li, Qiushi; Meng, Haihong; Sui, Xin; Zhang, Hongtao; Zhai, Xuhua

    2014-12-01

    The soft-killing laser weapon plays an important role in photoelectric defense technology. It can be used for photoelectric detection, search, blinding of photoelectric sensor and other devices on fire control and guidance devices, therefore it draws more and more attentions by many scholars. High power fiber-optic laser has many virtues such as small volume, simple structure, nimble handling, high efficiency, qualified light beam, easy thermal management, leading to blinding. Consequently, it may be used as the key device of soft-killing laser weapon. The present study introduced the development of high power fiber-optic laser and its main features. Meanwhile the key technology of large mode area (LMA) optical fiber design, the beam combination technology, double-clad fiber technology and pumping optical coupling technology was stated. The present study is aimed to design high doping LMA fiber, ensure single mode output by increasing core diameter and decrease NA. By means of reducing the spontaneous emission particle absorbed by fiber core and Increasing the power density in the optical fiber, the threshold power of nonlinear effect can increase, and the power of single fiber will be improved. Meantime, high power will be obtained by the beam combination technology. Application prospect of high power fiber laser in photoelectric defense technology was also set forth. Lastly, the present study explored the advantages of high power fiber laser in photoelectric defense technology.

  17. High power lasers & systems

    OpenAIRE

    Chatwin, Chris; Young, Rupert; Birch, Philip

    2015-01-01

    Some laser history;\\ud Airborne Laser Testbed & Chemical Oxygen Iodine Laser (COIL);\\ud Laser modes and beam propagation;\\ud Fibre lasers and applications;\\ud US Navy Laser system – NRL 33kW fibre laser;\\ud Lockheed Martin 30kW fibre laser;\\ud Conclusions

  18. Recent advances in phosphate laser glasses for high power applications

    Energy Technology Data Exchange (ETDEWEB)

    Campbell, J.H.

    1996-05-14

    Recent advances in Nd-doped phosphate laser glasses for high-peak-power and high-average-power applications are reviewed. Compositional studies have progressed to the point that glasses can be tailored to have specific properties for specific applications. Non-radiative relaxation effects can be accurately modeled and empirical expressions have been developed to evaluate both intrinsic (structural) and extrinsic (contamination induced) relaxation effects. Losses due to surface scattering and bulk glass absorption have been carefully measured and can be accurately predicted. Improvements in processing have lead to high damage threshold (e.g. Pt inclusion free) and high thermal shock resistant glasses with improved edge claddings. High optical quality pieces up to 79 x 45 x 4cm{sup 3} have been made and methods for continuous melting laser glass are under development.

  19. Microgravity Spray Cooling Research for High Powered Laser Applications

    Science.gov (United States)

    Zivich, Chad P.

    2004-01-01

    An extremely powerful laser is being developed at Goddard Space Flight Center for use on a satellite. This laser has several potential applications. One application is to use it for upper atmosphere weather research. In this case, the laser would reflect off aerosols in the upper atmosphere and bounce back to the satellite, where the aerosol velocities could be calculated and thus the upper atmosphere weather patterns could be monitored. A second application would be for the US. Air Force, which wants to use the laser strategically as a weapon for satellite defense. The Air Force fears that in the coming years as more and more nations gain limited space capabilities that American satellites may become targets, and the laser could protect the satellites. Regardless of the ultimate application, however, a critical step along the way to putting the laser in space is finding a way to efficiently cool it. While operating the laser becomes very hot and must be cooled to prevent overheating. On earth, this is accomplished by simply running cool tap water over the laser to keep it cool. But on a satellite, this is too inefficient. This would require too much water mass to be practical. Instead, we are investigating spray cooling as a means to cool the laser in microgravity. Spray cooling requires much less volume of fluid, and thus could be suitable for use on a satellite. We have inherited a 2.2 second Drop Tower rig to conduct our research with. In our experiments, water is pressurized with a compressed air tank and sprayed through a nozzle onto our test plate. We can vary the pressure applied to the water and the temperature of the plate before an experiment trial. The whole process takes place in simulated microgravity in the 2.2 second Drop Tower, and a high speed video camera records the spray as it hits the plate. We have made much progress in the past few weeks on these experiments. The rig originally did not have the capability to heat the test plate, but I did

  20. High-power pulsed lasers

    Energy Technology Data Exchange (ETDEWEB)

    Holzrichter, J.F.

    1980-04-02

    The ideas that led to the successful construction and operation of large multibeam fusion lasers at the Lawrence Livermore Laboratory are reviewed. These lasers are based on the use of Nd:glass laser materials. However, most of the concepts are applicable to any laser being designed for fusion experimentation. This report is a summary of lectures given by the author at the 20th Scottish University Summer School in Physics, on Laser Plasma Interaction. This report includes basic concepts of the laser plasma system, a discussion of lasers that are useful for short-pulse, high-power operation, laser design constraints, optical diagnostics, and system organization.

  1. High Power Lasers And Their Application In Materials Processing

    Science.gov (United States)

    Bohn, W. L.

    1985-02-01

    The idea of using a laser for materials processing is more than 20 years old. Although the concept of a non-contact method for processing with a beam of light has been pursued with great interest and enthusiasm, the practical use of laser beam processing was slow to develop. The lasers available in the 1960's were fragile and of relatively low power. In the 1970's lasers in the multi-kilowatt range were developed but the problem of laser acceptance by the customer had to be overcome. Today, reliable Nd-Yag and CO2-lasers are available and laser processing is a fast growing market. An additional boost is expected with the development of the next generation of lasers and with increased knowledge of the physical phenomena that underlie laser material processing. This paper will review latest developments in laser technology and laser-workpiece interaction with special emphasis on the impact of high speed photography on the research work in these areas.

  2. Optics assembly for high power laser tools

    Science.gov (United States)

    Fraze, Jason D.; Faircloth, Brian O.; Zediker, Mark S.

    2016-06-07

    There is provided a high power laser rotational optical assembly for use with, or in high power laser tools for performing high power laser operations. In particular, the optical assembly finds applications in performing high power laser operations on, and in, remote and difficult to access locations. The optical assembly has rotational seals and bearing configurations to avoid contamination of the laser beam path and optics.

  3. Optics assembly for high power laser tools

    Energy Technology Data Exchange (ETDEWEB)

    Fraze, Jason D.; Faircloth, Brian O.; Zediker, Mark S.

    2016-06-07

    There is provided a high power laser rotational optical assembly for use with, or in high power laser tools for performing high power laser operations. In particular, the optical assembly finds applications in performing high power laser operations on, and in, remote and difficult to access locations. The optical assembly has rotational seals and bearing configurations to avoid contamination of the laser beam path and optics.

  4. Laser assisted die bending: a new application of high power diode lasers

    Science.gov (United States)

    Schuöcker, D.; Schumi, T.; Spitzer, O.; Bammer, F.; Schuöcker, G.; Sperrer, G.

    2015-02-01

    Nowadays high power lasers are mainly used for cutting of sheet metals, for welding, hardening and rapid prototyping. In the forming of sheet metals as bending or deep drawing lasers are not used. Nevertheless a few years ago a new application of high power lasers has been invented, where bending of materials that break at room temperature becomes possible by heating them along the bending edge with high power lasers thus allowing their treatment without cracks and rupture. For this purpose a large number of diode lasers are arranged in the bottom tool of a bending machine (a V-shaped die) which heat up the initially flat sheet metal during the bending process what is performed by pressing it into the die with a knife shaped upper tool where due to the laser heating the material is softened and thus cracks are avoided. For the technical realization of the new process of laser assisted die bending, modules equipped with numerous laser diodes and a total beam power of 2,5 kW are used. The light emitted by these modules enters a tool with a length of 15cm and is deflected towards the workpiece. By using ten of these modules with adjacent dies and by integrating those in a bending press a bending edge of sheet metals with a length of 1500mm can be realized. Such a bending press with laser assistance also needs energization with a power of practically 50kW, a respective water flow, a heat exchanger system and also a control for all functions of this system. Special measures have also been developed to avoid radiating of those tools that are not covered by a workpiece in the case of bending edges shorter than the full length of the bending tools whereas individual short circuiting of diode modules can be performed. Specific measures to ensure a safe operation without any harm to the operational person have been realized. Exploitation of the bending process has been carried out for titanium, where material thicknesses up to 3mm have been bent successfully.

  5. Research and development of neodymium phosphate laser glass for high power laser application

    Science.gov (United States)

    Hu, Lili; He, Dongbing; Chen, Huiyu; Wang, Xin; Meng, Tao; Wen, Lei; Hu, Junjiang; Xu, Yongchun; Li, Shunguang; Chen, Youkuo; Chen, Wei; Chen, Shubin; Tang, Jingping; Wang, Biao

    2016-12-01

    Neodymium phosphate laser glass is a key optical element for high-power laser facility. In this work, the latest research and development of neodymium phosphate laser glass at the Shanghai Institute of Optics and Fine Mechanics (SIOM), China, is addressed. Neodymium phosphate laser glasses, N31, N41, NAP2, and NAP4, for high peak power and high average power applications have been developed. The properties of these glasses are presented and compared to those of other commercial neodymium phosphate laser glass from the Schott and Hoya companies and the Vavilov State Optical Institute (GOI), Russia. Continuous melting and edge cladding are the two key fabrication techniques that are used for the mass production of neodymium phosphate laser glass slabs. These techniques for the fabrication of large-aperture N31 neodymium phosphate laser glass slabs with low stress birefringence and residual reflectivity have been developed by us The effect of acid etching on the microstructure, optical transmission, and mechanical properties of NAP2 glass is also discussed.

  6. Research and development of neodymium phosphate laser glass for high power laser application

    Science.gov (United States)

    Hu, Lili; He, Dongbing; Chen, Huiyu; Wang, Xin; Meng, Tao; Wen, Lei; Hu, Junjiang; Xu, Yongchun; Li, Shunguang; Chen, Youkuo; Chen, Wei; Chen, Shubin; Tang, Jingping; Wang, Biao

    2017-01-01

    Neodymium phosphate laser glass is a key optical element for high-power laser facility. In this work, the latest research and development of neodymium phosphate laser glass at the Shanghai Institute of Optics and Fine Mechanics (SIOM), China, is addressed. Neodymium phosphate laser glasses, N31, N41, NAP2, and NAP4, for high peak power and high average power applications have been developed. The properties of these glasses are presented and compared to those of other commercial neodymium phosphate laser glass from the Schott and Hoya companies and the Vavilov State Optical Institute (GOI), Russia. Continuous melting and edge cladding are the two key fabrication techniques that are used for the mass production of neodymium phosphate laser glass slabs. These techniques for the fabrication of large-aperture N31 neodymium phosphate laser glass slabs with low stress birefringence and residual reflectivity have been developed by us The effect of acid etching on the microstructure, optical transmission, and mechanical properties of NAP2 glass is also discussed.

  7. High-power random distributed feedback fiber laser: From science to application

    Energy Technology Data Exchange (ETDEWEB)

    Du, Xueyuan [College of Optoelectronic Science and Engineering, National University of Defense Technology, Changsha 410073 (China); Naval Academy of Armament, Beijing 100161 (China); Zhang, Hanwei; Xiao, Hu; Ma, Pengfei; Wang, Xiaolin; Zhou, Pu; Liu, Zejin [College of Optoelectronic Science and Engineering, National University of Defense Technology, Changsha 410073 (China)

    2016-10-15

    A fiber laser based on random distributed feedback has attracted increasing attention in recent years, as it has become an important photonic device and has found wide applications in fiber communications or sensing. In this article, recent advances in high-power random distributed feedback fiber laser are reviewed, including the theoretical analyses, experimental approaches, discussion on the practical applications and outlook. It is found that a random distributed feedback fiber laser can not only act as an information photonics device, but also has the feasibility for high-efficiency/high-power generation, which makes it competitive with conventional high-power laser sources. In addition, high-power random distributed feedback fiber laser has been successfully applied for midinfrared lasing, frequency doubling to the visible and high-quality imaging. It is believed that the high-power random distributed feedback fiber laser could become a promising light source with simple and economic configurations. (copyright 2016 by WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  8. High power lasers

    CERN Document Server

    Niku-Lari, A

    1989-01-01

    The use of lasers for the working and treatment of materials is becoming increasingly common in industry. However, certain laser applications, for example, in welding, cutting and drilling, are more widely exploited than others. Whilst the potential of lasers for the surface treatment of metals is well recognised, in practice, this particular application is a relative newcomer. The 24 papers in this volume present the latest research and engineering developments in the use of lasers for processes such as surface melting, surface alloying and cladding, and machining, as well as discussing th

  9. High power CO II lasers and their material processing applications at Centre for Advanced Technology, India

    Science.gov (United States)

    Nath, A. K.; Paul, C. P.; Rao, B. T.; Kau, R.; Raghu, T.; Mazumdar, J. Dutta; Dayal, R. K.; Mudali, U. Kamachi; Sastikumar, D.; Gandhi, B. K.

    2006-01-01

    We have developed high power transverse flow (TF) CW CO II lasers up to 15kW, a high repetition rate TEA CO II laser of 500Hz, 500W average power and a RF excited fast axial flow CO II laser at the Centre for Advanced Technology and have carried out various material processing applications with these lasers. We observed very little variation of discharge voltage with electrode gap in TF CO II lasers. With optimally modulated laser beam we obtained better results in laser piercing and cutting of titanium and resolidification of 3 16L stainless steel weld-metal for improving intergranular corrosion resistance. We carried out microstructure and phase analysis of laser bent 304 stainless steel sheet and optimum process zones were obtained. We carried out laser cladding of 316L stainless steel and Al-alloy substrates with Mo, WC, and Cr IIC 3 powder to improve their wear characteristics. We developed a laser rapid manufacturing facility and fabricated components of various geometries with minimum surface roughness of 5-7 microns Ra and surface waviness of 45 microns between overlapped layers using Colmonoy-6, 3 16L stainless steel and Inconel powders. Cutting of thick concrete blocks by repeated laser glazing followed by mechanical scrubbing process and drilling holes on a vertical concrete with laser beam incident at an optimum angle allowing molten material to flow out under gravity were also done. Some of these studies are briefly presented here.

  10. Applications of high power lasers. [using reflection holograms for machining and surface treatment

    Science.gov (United States)

    Angus, J. C.

    1979-01-01

    The use of computer generated, reflection holograms in conjunction with high power lasers for precision machining of metals and ceramics was investigated. The Reflection holograms which were developed and made to work at both optical wavelength (He-Ne, 6328 A) and infrared (CO2, 10.6) meet the primary practical requirement of ruggedness and are relatively economical and simple to fabricate. The technology is sufficiently advanced now so that reflection holography could indeed be used as a practical manufacturing device in certain applications requiring low power densities. However, the present holograms are energy inefficient and much of the laser power is lost in the zero order spot and higher diffraction orders. Improvements of laser machining over conventional methods are discussed and addition applications are listed. Possible uses in the electronics industry include drilling holes in printed circuit boards making soldered connections, and resistor trimming.

  11. Packaging of high power semiconductor lasers

    CERN Document Server

    Liu, Xingsheng; Xiong, Lingling; Liu, Hui

    2014-01-01

    This book introduces high power semiconductor laser packaging design. The characteristics and challenges of the design and various packaging, processing, and testing techniques are detailed by the authors. New technologies, in particular thermal technologies, current applications, and trends in high power semiconductor laser packaging are described at length and assessed.

  12. High power fiber coupled diode lasers for display and lighting applications

    Science.gov (United States)

    Drovs, Simon; Unger, Andreas; Dürsch, Sascha; Köhler, Bernd; Biesenbach, Jens

    2017-02-01

    The performance of diode lasers in the visible spectral range has been continuously improved within the last few years, which was mainly driven by the goal to replace arc lamps in cinema or home projectors. In addition, the availability of such high power visible diode lasers also enables new applications in the medical field, but also the usage as pump sources for other solid state lasers. This paper summarizes the latest developments of fiber coupled sources with output power from 1.4 W to 120 W coupled into 100 μm to 400 μm fibers in the spectral range around 405 nm and 640 nm. New developments also include the use of fiber coupled multi single emitter arrays at 450 nm, as well as very compact modules with multi-W output power.

  13. Development of diffractive antireflection structures on ZnSe for high power CO II laser applications

    Science.gov (United States)

    Reversat, Fabien; Berthou, Thierry; Tisserand, Stéphane; Dupuy, Lionel; Gautier, Sophie; Muys, Peter; Delbeke, Danae; Grojo, David; Laraichi, Mohammed; Delaporte, Philippe

    2008-04-01

    The unavoidable absorption of thin films used in antireflective coatings forms a permanent bottleneck in the development of optics for high power laser applications. A valid alternative would be the micro-structuring of the optics surface, realizing a diffraction grating which emulates the functioning of an Anti-Reflection thin film layer. Due to the absence of film material, this diffractive structure would not contribute to the overall absorption of the optics. This paper investigates the practical limits of this strategy, applied to zinc selenide as low absorption infrared substrate material.

  14. High Power Dye Lasers

    Science.gov (United States)

    1975-09-30

    art capabilities for developmental models of hydrogen thyratrons and solid state thyristors. Table II-l is a list of switches that have been... thyratron Table II-l Switch Ignitron GE, GL - 37207 Hydrogen Thyratron High Power Switches Peak Cur. (kA) RMS Cm. (A) 300 120 Max. Rep Rate...for 2 usec Pulse Cli„) 8 1. EG&G HY-5 2. EW. GHT9 3. EG&G Develop- mental model Thyristors 5 7.5 15 125 335 350 300 1000 300 RCA

  15. Towards swift ion bunch acceleration by high-power laser pulses at the Centre for Advanced Laser Applications (CALA)

    Science.gov (United States)

    Lindner, F. H.; Haffa, D.; Bin, J. H.; Englbrecht, F.; Gao, Y.; Gebhard, J.; Hartmann, J.; Hilz, P.; Kreuzer, C.; Lehrack, S.; Ostermayr, T. M.; Rösch, T. F.; Speicher, M.; Würl, M.; Parodi, K.; Schreiber, J.; Thirolf, P. G.

    2017-07-01

    Laser-driven acceleration of ions has inspired novel applications, that can benefit from ion bunch properties different from conventionally (non-laser based) accelerated particle beams. Those differences range from extremely short bunch durations, broad energy spectra, large divergence angles and small source sizes to ultra-high ion bunch densities. So far, the main focus of research has been concentrating on the physics of the interaction of intense laser pulses with plasmas and the related mechanisms of ion acceleration. Now, the new Centre for Advanced Laser Applications (CALA) near Munich aims at pushing these ion bunches towards applications, including radiation therapy of tumors and the development of heavy ion bunches with solid-state-like density. These are needed for novel reaction mechanisms ('fission-fusion') to study the origin of heavy elements in the universe and to prepare for related studies at the upcoming EU-funded high-power laser facility ELI - Nuclear Physics in Bucharest.

  16. High Power Vanadate lasers

    CSIR Research Space (South Africa)

    Strauss, HJ

    2006-07-01

    Full Text Available right Directly comparing two equally doped crystals under lasing conditions will contribute to this debate. 3) No end-pumped vanadate the 100W range. 4) There is a strong interest in this for numerous applications in industry and the medical field...

  17. Advances in high power semiconductor diode lasers

    Science.gov (United States)

    Ma, Xiaoyu; Zhong, Li

    2008-03-01

    High power semiconductor lasers have broad applications in the fields of military and industry. Recent advances in high power semiconductor lasers are reviewed mainly in two aspects: improvements of diode lasers performance and optimization of packaging architectures of diode laser bars. Factors which determine the performance of diode lasers, such as power conversion efficiency, temperature of operation, reliability, wavelength stabilization etc., result from a combination of new semiconductor materials, new diode structures, careful material processing of bars. The latest progress of today's high-power diode lasers at home and abroad is briefly discussed and typical data are presented. The packaging process is of decisive importance for the applicability of high-power diode laser bars, not only technically but also economically. The packaging techniques include the material choosing and the structure optimizing of heat-sinks, the bonding between the array and the heat-sink, the cooling and the fiber coupling, etc. The status of packaging techniques is stressed. There are basically three different diode package architectural options according to the integration grade. Since the package design is dominated by the cooling aspect, different effective cooling techniques are promoted by different package architectures and specific demands. The benefit and utility of each package are strongly dependent upon the fundamental optoelectronic properties of the individual diode laser bars. Factors which influence these properties are outlined and comparisons of packaging approaches for these materials are made. Modularity of package for special application requirements is an important developing tendency for high power diode lasers.

  18. High power lasers in manufacturing

    OpenAIRE

    Chatwin, Chris R

    2017-01-01

    Lecture covers a brief history of lasers and the important beam parameters for manufacturing applications. It introduces the main laser types that are appropriate for manufacturing: carbon dioxide lasers, Nd YAG, Diode and fibre lasers, excimer lasers. It then looks at applications to different products and also micro-engineering

  19. Advances in industrial high-power lasers

    Science.gov (United States)

    Schlueter, Holger

    2005-03-01

    Four major types of laser sources are used for material processing. Excluding Excimer lasers, this paper focuses on advances in High Power CO2 lasers, Solid State Lasers and Diode Lasers. Because of their unrivaled cost to brightness relationship the fast axial flow CO2 laser remains unrivaled for flat-sheet laser cutting. Adding approximately a kW of output power ever four years, this laser type has been propelling the entire sheet metal fabrication industry for the last two decades. Very robust, diffusion cooled annular discharge CO2 lasers with 2kW output power have enabled robot mounted lasers for 3D applications. Solid State Lasers are chosen mainly because of the option of fiber delivery. Industrial applications still rely on lamp-pumped Nd:YAG lasers with guaranteed output powers of 4.5 kW at the workpiece. The introduction of the diode pumped Thin Disc Laser 4.5 kW laser enables new applications such as the Programmable Focus Optics. Pumping the Thin Disc Laser requires highly reliable High Power Diode Lasers. The necessary reliability can only be achieved in a modern, automated semiconductor manufacturing facility. For Diode Lasers, electro-optical efficiencies above 65% are as important as the passivation of the facets to avoid Burn-In power degradation.

  20. Beam Profile Improvement of a High-Power Diode Laser Stack for Optoacoustic Applications

    Science.gov (United States)

    Sánchez, Miguel; Rodríguez, Sergio; Leggio, Luca; Gawali, Sandeep; Gallego, Daniel; Lamela, Horacio

    2017-04-01

    Recent advances in high-power diode lasers (HPDLs) technology allow their use as potential sources for optoacoustic (OA) applications, due to their high repetition rates (a few kHz), low costs and sizes. However, some OA applications require pulse energies in the order of mJ that cannot be provided by the only HPDLs (several μJ). The employment of diode laser bars (DLBs) and stacks (DLSs) significantly increases the energy per pulse up to several mJ, but they require more optical elements for collimation in fast and slow axes. In this work, we show an 808 nm DLS emitting optical nanosecond pulses with currents of ˜ 200 A and supplied by a customized current driver. We only collimate the beam in the fast axis by disposing the core of 200 μm optical fibers as collimating lenses along each bar of the stack, and we discuss the improvement of the beam profile. The results demonstrate that the beam profile is notably improved with the optical fiber lenses, and a 6.4 mm × 4.3 mm light spot is obtained by using a conventional focusing lens. Measurements report a total energy per pulse of 630 μJ in the spot, considering a pulse width of 850 ns and a repetition rate of 1 kHz. Finally, we focus the light spot into an absorbing inclusion (graphene oxide) hosted in a semi-transparent phantom to generate and detect high OA signals ({˜ }355 mV_{pp}). The results achieved demonstrate the capability of our DLS system to be applied in multispectral OA systems with final application in OA endoscopy and microscopy.

  1. The future of high power laser techniques

    Science.gov (United States)

    Poprawe, Reinhart; Loosen, Peter; Hoffmann, Hans-Dieter

    2007-05-01

    High Power Lasers have been used for years in corresponding applications. Constantly new areas and new processes have been demonstrated, developed and transferred to fruitful use in industry. With the advent of diode pumped solid state lasers in the multi-kW-power regime at beam qualities not far away from the diffraction limit, a new area of applicability has opened. In welding applications speeds could be increased and systems could be developed with higher efficiently leading also to new perspectives for increased productivity, e.g. in combined processing. Quality control is increasingly demanded by the applying industries, however applications still are rare. Higher resolution of coaxial process control systems in time and space combined with new strategies in signal processing could give rise to new applications. The general approach described in this paper emphasizes the fact, that laser applications can be developed more efficiently, more precisely and with higher quality, if the laser radiation is tailored properly to the corresponding application. In applying laser sources, the parameter ranges applicable are by far wider and more flexible compared to heat, mechanical or even electrical energy. The time frame ranges from several fs to continuous wave and this spans approximately 15 orders of magnitude. Spacewise, the foci range from several µm to cm and the resulting intensities suitable for materials processing span eight orders of magnitude from 10 3 to 10 11 W/cm2. In addition to space (power, intensity) and time (pulse) the wavelength can be chosen as a further parameter of optimization. As a consequence, the resulting new applications are vast and can be utilized in almost every market segment of our global economy (Fig. 1). In the past and only partly today, however, this flexibility of laser technology is not exploited in full in materials processing, basically because in the high power regime the lasers with tailored beam properties are not

  2. Optical systems for high-power laser applications: principles and design aspects

    NARCIS (Netherlands)

    Beckmann, L.H.J.F.; Ehrlichmann, D.

    1995-01-01

    Starting from the optical properties of laser beams, the requirements of optical systems for manipulating laser radiation in industrial applications are derived. The relevant parameters, relations to the diffraction limit and the state-of-the-art design techniques are discussed. The three important

  3. Narrow-line, tunable, high-power diode laser pump for DPAL applications

    Science.gov (United States)

    Pandey, Rajiv; Merchen, David; Stapleton, Dean; Irwin, David; Humble, Chuck; Patterson, Steve; Kissel, Heiko; Biesenbach, Jens

    2013-05-01

    We report on a high-power diode laser pump source for diode-pumped alkali lasers (DPAL), specifically rubidium alkali vapor lasers at 780nm, delivering up to 100W/bar with FWHM spectral line width of 0.06nm (~30GHz). This pump is based on a micro-channel water-cooled stack with collimation in both-axes. Wavelength-locking of the output spectrum allows absorption in one of the very narrow resonance lines of the atomic rubidium alkali vapor. To achieve these results, research was conducted to deliver the highest performance on all key components of the product from the diode laser bar which produces the optical power at 780nm to the external Bragg gratings which narrow the spectrum line width. We highlight the advancements in the epitaxy, device design, beam collimation, grating selection, alignment, tunability and thermal control that enable realization of this novel pump-source for DPALs. Design trade-offs will be presented.

  4. JENOPTIK diode lasers and bars optimized for high-power applications in the NIR range

    Science.gov (United States)

    Zorn, M.; Hülsewede, R.; Schulze, H.; Sebastian, J.; Hennig, P.; Schröder, D.

    2010-02-01

    Laser diodes and laser bars for the high-volume wavelength ranges at 808 nm and 940 nm are available in optimized design and high quality. However, a lot of other wavelengths in the NIR are needed for specialized applications also requiring high stability, reliability and a good efficiency with a good beam quality. An efficient adaptation of the laser diode design to optimize the laser performance at the customized wavelength is highly desirable. At JENOPTIK Diode Lab (JDL) we therefore focus on a flexible and competitive laser diode design resulting in a high output power and a high efficiency at reasonable production costs. Starting from excellent laser bars at 808 nm and 940 nm laser bars with emission wavelengths around 790 nm, 830 nm, 880nm (cw) and 940 nm (pulsed operation) are developed. For 792 nm a maximum output power of 90 W and an efficiency of 55 % has been achieved with an expected lifetime of more than 15000 hours. At 825 nm a maximum efficiency of 60 % and 60 W output power for more than 20.000 h with a high degree of polarization can be presented. Changing the quantum well material for 885 nm the output power reaches 125W with 63% efficiency also for more than 25.000 hours. Laser bars for pulsed applications (quasi-cw) at 940 nm result in an output power of 500 W with an efficiency of 60 %.

  5. In-volume heating using high-power laser diodes

    NARCIS (Netherlands)

    Denisenkov, V.S.; Kiyko, V.V.; Vdovin, G.V.

    2015-01-01

    High-power lasers are useful instruments suitable for applications in various fields; the most common industrial applications include cutting and welding. We propose a new application of high-power laser diodes as in-bulk heating source for food industry. Current heating processes use surface

  6. In-volume heating using high-power laser diodes

    NARCIS (Netherlands)

    Denisenkov, V.S.; Kiyko, V.V.; Vdovin, G.V.

    2015-01-01

    High-power lasers are useful instruments suitable for applications in various fields; the most common industrial applications include cutting and welding. We propose a new application of high-power laser diodes as in-bulk heating source for food industry. Current heating processes use surface heatin

  7. High power laser perforating tools and systems

    Science.gov (United States)

    Zediker, Mark S; Rinzler, Charles C; Faircloth, Brian O; Koblick, Yeshaya; Moxley, Joel F

    2014-04-22

    ystems devices and methods for the transmission of 1 kW or more of laser energy deep into the earth and for the suppression of associated nonlinear phenomena. Systems, devices and methods for the laser perforation of a borehole in the earth. These systems can deliver high power laser energy down a deep borehole, while maintaining the high power to perforate such boreholes.

  8. Drivers for High Power Laser Diodes

    Institute of Scientific and Technical Information of China (English)

    Yankov P; Todorov D; Saramov E

    2006-01-01

    During the last year the high power laser diodes jumped over the 1 kW level of CW power for a stack,and the commercial 1 cm bars reached 100 W output optical power at the standard wavelengths around 800 nm and 980 nm. The prices are reaching the industry acceptable levels. All Nd:YAG and fiber industrial lasers manufacturers have developed kW prototypes. Those achievements have set new requirements for the power supplies manufactuers-high and stable output current, and possibilities for fast control of the driving current, keeping safe the expensive laser diode. The fast switching frequencies also allow long range free space communications and optical range finding. The high frequencies allow the design of a 3D laser radar with high resolution and other military applications. The prospects for direct laser diode micro machining are also attractive.

  9. Bulk damage and absorption in fused silica due to high-power laser applications

    Science.gov (United States)

    Nürnberg, F.; Kühn, B.; Langner, A.; Altwein, M.; Schötz, G.; Takke, R.; Thomas, S.; Vydra, J.

    2015-11-01

    Laser fusion projects are heading for IR optics with high broadband transmission, high shock and temperature resistance, long laser durability, and best purity. For this application, fused silica is an excellent choice. The energy density threshold on IR laser optics is mainly influenced by the purity and homogeneity of the fused silica. The absorption behavior regarding the hydroxyl content was studied for various synthetic fused silica grades. The main absorption influenced by OH vibrational excitation leads to different IR attenuations for OH-rich and low-OH fused silica. Industrial laser systems aim for the maximum energy extraction possible. Heraeus Quarzglas developed an Yb-doped fused silica fiber to support this growing market. But the performance of laser welding and cutting systems is fundamentally limited by beam quality and stability of focus. Since absorption in the optical components of optical systems has a detrimental effect on the laser focus shift, the beam energy loss and the resulting heating has to be minimized both in the bulk materials and at the coated surfaces. In collaboration with a laser research institute, an optical finisher and end users, photo thermal absorption measurements on coated samples of different fused silica grades were performed to investigate the influence of basic material properties on the absorption level. High purity, synthetic fused silica is as well the material of choice for optical components designed for DUV applications (wavelength range 160 nm - 260 nm). For higher light intensities, e.g. provided by Excimer lasers, UV photons may generate defect centers that effect the optical properties during usage, resulting in an aging of the optical components (UV radiation damage). Powerful Excimer lasers require optical materials that can withstand photon energy close to the band gap and the high intensity of the short pulse length. The UV transmission loss is restricted to the DUV wavelength range below 300 nm and

  10. Recent advances in phosphate laser glasses for high power applications. Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    Campbell, J.H.

    1996-05-01

    Recent advances in Nd-doped phosphate laser glasses for high-peak-power and high-average-power applications are reviewed. Compositional studies have progressed to the point that glasses can be tailored to have specific properties for specific applications. Non-radiative relaxation effects can be accurately modeled and empirical expressions have been developed to evaluate both intrinsic (structural) and extrinsic (contamination induced) relaxation effects. Losses due to surface scattering and bulk glass absorption have been carefully measured and can be accurately predicted. Improvements in processing have lead to high damage threshold (e.g. Pt inclusion free) and high thermal shock resistant glasses with improved edge claddings. High optical quality pieces up to 79 x 45 x 4 cm{sup 3} have been made and methods for continuous melting laser glass are under development.

  11. LASERIX: An open facility for developments of EUV and soft X-ray lasers and applications-Developments of XUV sources using high power laser facilities: ILE, ELI

    Energy Technology Data Exchange (ETDEWEB)

    Ros, D., E-mail: david.ros@u-psud.fr [CLUPS-LUMAT, Universite Paris Sud 11-CNRS (France); LPGP, CNRS-Universite Paris Sud 11 (France); Cassou, K.; Cros, B.; Daboussi, S. [CLUPS-LUMAT, Universite Paris Sud 11-CNRS (France); LPGP, CNRS-Universite Paris Sud 11 (France); Demailly, J. [CLUPS-LUMAT, Universite Paris Sud 11-CNRS (France); Guilbaud, O.; Kazamias, S.; Lagron, J.-C. [CLUPS-LUMAT, Universite Paris Sud 11-CNRS (France); LPGP, CNRS-Universite Paris Sud 11 (France); Maynard, G. [LPGP, CNRS-Universite Paris Sud 11 (France); Neveu, O.; Pittman, M. [CLUPS-LUMAT, Universite Paris Sud 11-CNRS (France); LPGP, CNRS-Universite Paris Sud 11 (France); Zielbauer, B. [CLUPS-LUMAT, Universite Paris Sud 11-CNRS (France); LPGP, CNRS-Universite Paris Sud 11 (France); GSI Darmstadt (Germany); Zimmer, D. [CLUPS-LUMAT, Universite Paris Sud 11-CNRS (France); GSI Darmstadt (Germany); Kuhl, T. [GSI Darmstadt (Germany); Lacombe, S.; Porcel, E. [ISMO, CNRS-Universite Paris Sud 11 (France); Penhoat, M.-A. du [IMCP, Paris VI (France); Zeitoun, P. [LOA, ENSTA-Ecole Polytechnique-CNRS (France); Mourou, G. [ILE (France)

    2011-10-11

    LASERIX is a high-power laser facility leading to High-repetition-rate XUV laser pumped by Titanium:Sapphire laser. The aim of this laser facility is to offer Soft XRLs in the 30-7 nm range and auxiliary IR beam, which could also be used to produce synchronized XUV sources. In this contribution, the main results concerning both the development of XUV sources and their use for applications (irradiation of DNA samples) are presented, as well the present status and some perspectives for LASERIX.

  12. High power collimated diode laser stack

    Institute of Scientific and Technical Information of China (English)

    LIU Yuan-yuan; FANG Gao-zhan; MA Xiao-yu; LIU Su-ping; FENG Xiao-ming

    2006-01-01

    A high power collimated diode laser stack is carried out based on fast-axis collimation and stack packaging techniques.The module includes ten typical continuous wave (cw) bars and the total output power can be up to 368W at 48.6A.Using a cylindrical lens as the collimation elements,we can make the fast-axis divergence and the slow-axis divergence are 0.926 40 and 8.2060 respectively.The light emitting area is limited in a square area of 18.3 mm×11 mm.The module has the advantage of high power density and offers a wide potential applications in pumping and material processing.

  13. High power laser-driven ceramic phosphor plate for outstanding efficient white light conversion in application of automotive lighting.

    Science.gov (United States)

    Song, Young Hyun; Ji, Eun Kyung; Jeong, Byung Woo; Jung, Mong Kwon; Kim, Eun Young; Yoon, Dae Ho

    2016-08-09

    We report on Y3Al5O12: Ce(3+) ceramic phosphor plate (CPP) using nano phosphor for high power laser diode (LD) application for white light in automotive lighting. The prepared CPP shows improved luminous properties as a function of Ce(3+) concentration. The luminous properties of the Y3Al5O12: Ce(3+) CPP nano phosphor are improved when compared to the Y3Al5O12: Ce(3+) CPP with bulk phosphor, and hence, the luminous emittance, luminous flux, and conversion efficiency are improved. The Y3Al5O12: Ce(3+) CPP with an optimal Ce(3+) content of 0.5 mol % shows 2733 lm/mm(2) value under high power blue radiant flux density of 19.1 W/mm(2). The results indicate that Y3Al5O12: Ce(3+) CPP using nano phosphor can serve as a potential material for solid-state laser lighting in automotive applications.

  14. Ceramics for High Power Lasers

    Science.gov (United States)

    2013-07-01

    ICP-MS) on 25 elements ranging from transition metals, rare earths , alkali, alkaline earths and silicon on a set of selected YAG ceramics and...our knowledge of the origin of optical losses in ceramic laser host materials while initiating a program of research on 2-micron, thulium- doped fiber...During Year 1 of this program, we produced and characterized laser grade Nd:YAG and low optical loss Gd3+ doped YAG and Tm:YAG ceramics . Laser

  15. Direct High-Power Laser Acceleration of Ions for Medical Applications

    CERN Document Server

    Salamin, Y I; Keitel, C H

    2008-01-01

    Theoretical investigations show that linearly and radially polarized multiterawatt and petawatt laser beams, focused to subwavelength waist radii, can directly accelerate protons and carbon nuclei, over micron-size distances, to the energies required for hadron cancer therapy. Ions accelerated by radially polarized lasers have generally a more favorable energy spread than those accelerated by linearly polarized lasers of the same intensity.

  16. High power regenerative laser amplifier

    Science.gov (United States)

    Miller, J.L.; Hackel, L.A.; Dane, C.B.; Zapata, L.E.

    1994-02-08

    A regenerative amplifier design capable of operating at high energy per pulse, for instance, from 20-100 Joules, at moderate repetition rates, for instance from 5-20 Hertz is provided. The laser amplifier comprises a gain medium and source of pump energy coupled with the gain medium; a Pockels cell, which rotates an incident beam in response to application of a control signal; an optical relay system defining a first relay plane near the gain medium and a second relay plane near the rotator; and a plurality of reflectors configured to define an optical path through the gain medium, optical relay and Pockels cell, such that each transit of the optical path includes at least one pass through the gain medium and only one pass through the Pockels cell. An input coupler, and an output coupler are provided, implemented by a single polarizer. A control circuit coupled to the Pockels cell generates the control signal in timed relationship with the input pulse so that the input pulse is captured by the input coupler and proceeds through at least one transit of the optical path, and then the control signal is applied to cause rotation of the pulse to a polarization reflected by the polarizer, after which the captured pulse passes through the gain medium at least once more and is reflected out of the optical path by the polarizer before passing through the rotator again to provide an amplified pulse. 7 figures.

  17. Next generation 9xx/10xx nm high power laser diode bars for multi-kilowatt industrial applications

    Science.gov (United States)

    Commin, Paul; Todt, René; Krejci, Martin; Bättig, Rainer; Brunner, Reinhard; Lichtenstein, Norbert

    2013-02-01

    We report on the development of high power, 9xx-10xx nm laser diode bars for use in direct diode systems and for solidstate and fibre laser pumping with applications in industrial markets. For 1 cm wide bars on micro channel cooler (MCC) we have achieved a reliable output power of 250 W across the 900 nm - 1060 nm range. At this output power level we have achieved power conversion efficiencies of 65-66 % and 90 % power content slow axis beam divergence of ~6.5°. Results of a 6400 h life test show an average power degradation of 0.6 % per 1000 h at this operating power level. We will also show results of high power bars assembled on the new OCLARO conductive cooler, the BLM. This new cooler has a small footprint of 12.6 mm × 24.8 mm and is designed for lateral or vertical stacking of diodes in multi kilowatt systems but with the benefits associated with a conductive cooler. The thermal properties are shown to be the same as for a standard CS mount. 1 cm wide high fill factor bars and 0.5 cm wide low fill factor half bars assembled on the BLM operate at 63-64 % power conversion efficiency (PCE) with output powers of up to 250 W and 150 W, respectively.

  18. High Power Fiber Laser Test Bed

    Data.gov (United States)

    Federal Laboratory Consortium — This facility, unique within DoD, power-combines numerous cutting-edge fiber-coupled laser diode modules (FCLDM) to integrate pumping of high power rare earth-doped...

  19. Development and Application of a High Power ND-Glass Laser Instrument.

    Science.gov (United States)

    1985-01-01

    developed utilizing the new numerical method of Keefer, Peters , and Crowder to obtain a complete numerical solution for an absorber and nozzle...Ore., 1984, p. 227. 4. Wolpert, R. D., Photonics Spectra, 17, 12, 1983, p. 71. 5. Laskovar, B., Laser focus, 20, 2, 1984, p.7 3. .IV. 6. Leskovar , B... Peter Tsai, Graduate Assistant, September 1983-Present. Anticipated M.S. Thesis, "Stability Characteristics of Laser- Supported Plasmas." r=% 5

  20. System for time-resolved laser absorption spectroscopy and its application to high-power impulse magnetron sputtering

    Science.gov (United States)

    Adámek, P.; Olejníček, J.; Hubička, Z.; Čada, M.; Kment, Š.; Kohout, M.; Do, H. T.

    2017-02-01

    This paper deals with the development and construction of an apparatus for time-resolved tunable diode laser absorption spectroscopy (LAS) for the diagnostics of pulsed plasma. A detailed description of the extension of a progressive method of laser absorption spectroscopy in continuous regime to a direct triggering method of the time-resolved laser absorption spectroscopy (TR-LAS) is presented. The main advantage of the developed method is its capability to measure the time evolution of the whole absorption profile with a preset time resolution, which can be less than 1 μs. Therefore, the presented method of repetitive sampling applied on LAS in plasma processes is capable of simultaneous measurement of the density and kinetic temperature of selected particles. Its appropriate applications are to periodical processes in technological plasma, namely pulsed plasma discharges. The developed method of TR-LAS was applied to measurements of the temporal evolution of density and kinetic temperature of argon metastable species during high-power impulse magnetron sputtering of titanium and titanium dioxide thin films.

  1. High Power Short Wavelength Laser Development

    Science.gov (United States)

    1977-11-01

    Unlimited güä^äsjäsiiiüüü X NRTC-77-43R P I High Power Short Wavelength Laser Development November 1977 D. B. Cohn and W. B. Lacina...NO NRTC-77-43R, «. TITLE fana »uetjjitj BEFORE COMPLETING FORM CIPIENT’S CATALOO NUMBER KIGH.POWER SHORT WAVELENGTH LASER DEVELOPMENT , 7...fWhtn Data Enterte NRTC-77-43R HIGH POWER SHORT WAVELENGTH LASER DEVELOPMENT ARPA Order Number: Program Code Number: Contract Number: Principal

  2. Dual-rod Yb: YAG laser for high-power and high-brightness applications

    Energy Technology Data Exchange (ETDEWEB)

    Honea, E C; Beach, R; Mitchell, S C; Skidmore, J A; Emanuel, M A; Sutton, S B; Payne, S A; Avizonis, P V; Monroe, R S; Harris, D G

    2000-03-13

    The authors describe a diode-pumped Yb:YAG laser producing 1,080 W cw with 27.5% optical-optical efficiency and 532 W Q-switched with M{sup 2} = 2.2 and 17% optical-optical efficiency. The laser uses two composite Yb:YAG rods separated by a 90 degree quartz rotator for bifocusing compensation. A microlensed diode array end-pumps each rod using a hollow lens duct for pump delivery. By changing resonator parameters, they can adjust the fundamental mode size and the output beam quality. Using a flattened gaussian intensity profile to calculate the mode fill efficiency and clipping losses, the authors compare experimental data to modeled output power vs beam quality.

  3. High power diode lasers for solid-state laser pumps

    Science.gov (United States)

    Linden, Kurt J.; McDonnell, Patrick N.

    1994-02-01

    The development and commercial application of high power diode laser arrays for use as solid-state laser pumps is described. Such solid-state laser pumps are significantly more efficient and reliable than conventional flash-lamps. This paper describes the design and fabrication of diode lasers emitting in the 780 - 900 nm spectral region, and discusses their performance and reliability. Typical measured performance parameters include electrical-to-optical power conversion efficiencies of 50 percent, narrow-band spectral emission of 2 to 3 nm FWHM, pulsed output power levels of 50 watts/bar with reliability values of over 2 billion shots to date (tests to be terminated after 10 billion shots), and reliable operation to pulse lengths of 1 ms. Pulse lengths up to 5 ms have been demonstrated at derated power levels, and CW performance at various power levels has been evaluated in a 'bar-in-groove' laser package. These high-power 1-cm stacked-bar arrays are now being manufactured for OEM use. Individual diode laser bars, ready for package-mounting by OEM customers, are being sold as commodity items. Commercial and medical applications of these laser arrays include solid-state laser pumping for metal-working, cutting, industrial measurement and control, ranging, wind-shear/atmospheric turbulence detection, X-ray generation, materials surface cleaning, microsurgery, ophthalmology, dermatology, and dental procedures.

  4. Laser welding of polymers using high-power diode lasers

    Science.gov (United States)

    Bachmann, Friedrich G.; Russek, Ulrich A.

    2003-09-01

    Laser welding of polymers using high power diode lasers offers specific process advantages over conventional technologies, such as short process times while providing optically and qualitatively valuable weld seams, contactless yielding of the joining energy, absence of process induced vibrations, imposing minimal thermal stress and avoiding particle generation. Furthermore this method exhibits high integration capabilities and automatization potential. Moreover, because of the current favorable cost development within the high power diode laser market laser welding of polymers has become more and more an industrially accepted joining method. This novel technology permits both, reliable high quality joining of mechanically and electronically highly sensitive micro components and hermetic sealing of macro components. There are different welding strategies available, which are adaptable to the current application. Within the frame of this discourse scientific and also application oriented results concerning laser transmission welding of polymers using preferably diode lasers are presented. Besides the used laser systems the fundamental process strategies as well as decisive process parameters are illustrated. The importance of optical, thermal and mechanical properties is discussed. Applications at real technical components will be presented, demonstrating the industrial implementation capability and the advantages of a novel technology.

  5. Overview on the high power excimer laser technology

    Science.gov (United States)

    Liu, Jingru

    2013-05-01

    High power excimer laser has essential applications in the fields of high energy density physics, inertial fusion energy and industry owing to its advantages such as short wavelength, high gain, wide bandwidth, energy scalable and repetition operating ability. This overview is aimed at an introduction and evaluation of enormous endeavor of the international high power excimer laser community in the last 30 years. The main technologies of high power excimer laser are reviewed, which include the pumping source technology, angular multiplexing and pulse compressing, beam-smoothing and homogenous irradiation, high efficiency and repetitive operation et al. A high power XeCl laser system developed in NINT of China is described in detail.

  6. High power lasers: Sources, laser-material interactions, high excitations, and fast dynamics in laser processing and industrial applications; Proceedings of the Meeting, The Hague, Netherlands, Mar. 31-Apr. 3, 1987

    Science.gov (United States)

    Kreutz, E. W. (Editor); Quenzer, Alain (Editor); Schuoecker, Dieter (Editor)

    1987-01-01

    The design and operation of high-power lasers for industrial applications are discussed in reviews and reports. Topics addressed include the status of optical technology in the Netherlands, laser design, the deposition of optical energy, laser diagnostics, nonmetal processing, and energy coupling and plasma formation. Consideration is given to laser-induced damage to materials, fluid and gas flow dynamics, metal processing, and manufacturing. Graphs, diagrams, micrographs, and photographs are provided.

  7. Atmospheric propagation and combining of high-power lasers.

    Science.gov (United States)

    Nelson, W; Sprangle, P; Davis, C C

    2016-03-01

    In this paper, we analyze beam combining and atmospheric propagation of high-power lasers for directed-energy (DE) applications. The large linewidths inherent in high-power fiber and slab lasers cause random phase and intensity fluctuations that occur on subnanosecond time scales. Coherently combining these high-power lasers would involve instruments capable of precise phase control and operation at rates greater than ∼10  GHz. To the best of our knowledge, this technology does not currently exist. This presents a challenging problem when attempting to phase lock high-power lasers that is not encountered when phase locking low-power lasers, for example, at milliwatt power levels. Regardless, we demonstrate that even if instruments are developed that can precisely control the phase of high-power lasers, coherent combining is problematic for DE applications. The dephasing effects of atmospheric turbulence typically encountered in DE applications will degrade the coherent properties of the beam before it reaches the target. Through simulations, we find that coherent beam combining in moderate turbulence and over multikilometer propagation distances has little advantage over incoherent combining. Additionally, in cases of strong turbulence and multikilometer propagation ranges, we find nearly indistinguishable intensity profiles and virtually no difference in the energy on the target between coherently and incoherently combined laser beams. Consequently, we find that coherent beam combining at the transmitter plane is ineffective under typical atmospheric conditions.

  8. Freeform beam shaping for high-power multimode lasers

    Science.gov (United States)

    Laskin, Alexander; Laskin, Vadim

    2014-03-01

    Widening of using high power multimode lasers in industrial laser material processing is accompanied by special requirements to irradiance profiles in such technologies like metal or plastics welding, cladding, hardening, brazing, annealing, laser pumping and amplification in MOPA lasers. Typical irradiance distribution of high power multimode lasers: free space solid state, fiber-coupled solid state and diodes lasers, fiber lasers, is similar to Gaussian. Laser technologies can be essentially improved when irradiance distribution on a workpiece is uniform (flattop) or inverse-Gauss; when building high-power pulsed lasers it is possible to enhance efficiency of pumping and amplification by applying super-Gauss irradiance distribution with controlled convexity. Therefore, "freeform" beam shaping of multimode laser beams is an important task. A proved solution is refractive field mapping beam shaper like Shaper capable to control resulting irradiance profile - with the same unit it is possible to get various beam profiles and choose optimum one for a particular application. Operational principle of these devices implies transformation of laser irradiance distribution by conserving beam consistency, high transmittance, providing collimated low divergent output beam. Using additional optics makes it possible to create resulting laser spots of necessary size and round, elliptical or linear shape. Operation out of focal plane and, hence, in field of lower wavefront curvature, allows extending depth of field. The refractive beam shapers are implemented as telescopes and collimating systems, which can be connected directly to fiber-coupled lasers or fiber lasers, thus combining functions of beam collimation and irradiance transformation.

  9. Modeling of high power laser interaction with metals

    Science.gov (United States)

    Mustafa, Kurt; Zahide, Demircioǧlu

    2017-02-01

    Laser matter interaction has been very popular subject from the first recognition of lasers. Laser application in industry or laboratory applications are based on definite interactions of the laser beam with the workpiece. In this paper, an effective model related with high power radiation interaction with metals is presented. In metals, Lorentz-Drude model is used calculate permeability theoretically. The plasma frequency was calculated at various temperatures and using the obtained results the refractive index of the metal (Ag) was investigated. The calculation result revealed that the effect of the temperature need to be considered at reflection and transmission of the laser beam.

  10. High Power Picosecond Laser Pulse Recirculation

    Energy Technology Data Exchange (ETDEWEB)

    Shverdin, M Y; Jovanovic, I; Semenov, V A; Betts, S M; Brown, C; Gibson, D J; Shuttlesworth, R M; Hartemann, F V; Siders, C W; Barty, C P

    2010-04-12

    We demonstrate a nonlinear crystal-based short pulse recirculation cavity for trapping the second harmonic of an incident high power laser pulse. This scheme aims to increase the efficiency and flux of Compton-scattering based light sources. We demonstrate up to 36x average power enhancement of frequency doubled sub-millijoule picosecond pulses, and 17x average power enhancement of 177 mJ, 10 ps, 10 Hz pulses.

  11. High-power picosecond laser pulse recirculation.

    Science.gov (United States)

    Shverdin, M Y; Jovanovic, I; Semenov, V A; Betts, S M; Brown, C; Gibson, D J; Shuttlesworth, R M; Hartemann, F V; Siders, C W; Barty, C P J

    2010-07-01

    We demonstrate a nonlinear crystal-based short pulse recirculation cavity for trapping the second harmonic of an incident high-power laser pulse. This scheme aims to increase the efficiency and flux of Compton-scattering-based light sources. We demonstrate up to 40x average power enhancement of frequency-doubled submillijoule picosecond pulses, and 17x average power enhancement of 177 mJ, 10 ps, 10 Hz pulses.

  12. In-volume heating using high-power laser diodes

    Science.gov (United States)

    Denisenkov, Valentin S.; Kiyko, Vadim V.; Vdovin, Gleb V.

    2015-03-01

    High-power lasers are useful instruments suitable for applications in various fields; the most common industrial applications include cutting and welding. We propose a new application of high-power laser diodes as in-bulk heating source for food industry. Current heating processes use surface heating with different approaches to make the heat distribution more uniform and the process more efficient. High-power lasers can in theory provide in-bulk heating which can sufficiently increase the uniformity of heat distribution thus making the process more efficient. We chose two media (vegetable fat and glucose) for feasibility experiments. First, we checked if the media have necessary absorption coefficients on the wavelengths of commercially available laser diodes (940-980 nm). This was done using spectrophotometer at 700-1100 nm which provided the dependences of transmission from the wavelength. The results indicate that vegetable fat has noticeable transmission dip around 925 nm and glucose has sufficient dip at 990 nm. Then, after the feasibility check, we did numerical simulation of the heat distribution in bulk using finite elements method. Based on the results, optimal laser wavelength and illuminator configuration were selected. Finally, we carried out several pilot experiments with high-power diodes heating the chosen media.

  13. High power coherent polarization locked laser diode.

    Science.gov (United States)

    Purnawirman; Phua, P B

    2011-03-14

    We have coherently combined a broad area laser diode array to obtain high power single-lobed output by using coherent polarization locking. The single-lobed coherent beam is achieved by spatially combining four diode emitters using walk-off crystals and waveplates while their phases are passively locked via polarization discrimination. While our previous work focused on coherent polarization locking of diode in Gaussian beams, we demonstrate in this paper, the feasibility of the same polarization discrimination for locking multimode beams from broad area diode lasers. The resonator is designed to mitigate the loss from smile effect by using retro-reflection feedback in the cavity. In a 980 nm diode array, we produced 7.2 W coherent output with M2 of 1.5x11.5. The brightness of the diode is improved by more than an order of magnitude.

  14. Completely monolithic linearly polarized high-power fiber laser oscillator

    Science.gov (United States)

    Belke, Steffen; Becker, Frank; Neumann, Benjamin; Ruppik, Stefan; Hefter, Ulrich

    2014-03-01

    We have demonstrated a linearly polarized cw all-in-fiber oscillator providing 1 kW of output power and a polarization extinction ratio (PER) of up to 21.7 dB. The design of the laser oscillator is simple and consists of an Ytterbium-doped polarization maintaining large mode area (PLMA) fiber and suitable fiber Bragg gratings (FBG) in matching PLMA fibers. The oscillator has nearly diffraction-limited beam quality (M² high power 6+1:1 pump coupler. The slope efficiency of the laser is 75 %. The electro/optical efficiency of the complete laser system is ~30 % and hence in the range of Rofin's cw non-polarized fiber lasers. Choosing an adequate bending diameter for the Yb-doped PLMA fiber, one polarization mode as well as higher order modes are sufficiently supressed1. Resulting in a compact and robust linearly polarized high power single mode laser without external polarizing components. Linearly polarized lasers are well established for one dimensional cutting or welding applications. Using beam shaping optics radially polarized laser light can be generated to be independent from the angle of incident to the processing surface. Furthermore, high power linearly polarized laser light is fundamental for nonlinear frequency conversion of nonlinear materials.

  15. Apparatus for advancing a wellbore using high power laser energy

    Science.gov (United States)

    Zediker, Mark S.; Land, Mark S.; Rinzler, Charles C.; Faircloth, Brian O.; Koblick, Yeshaya; Moxley, Joel F.

    2014-09-02

    Delivering high power laser energy to form a borehole deep into the earth using laser energy. Down hole laser tools, laser systems and laser delivery techniques for advancement, workover and completion activities. A laser bottom hole assembly (LBHA) for the delivery of high power laser energy to the surfaces of a borehole, which assembly may have laser optics, a fluid path for debris removal and a mechanical means to remove earth.

  16. Compact High Power Fiber Laser Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The goal of the proposed work is the development of a portable and efficient pulsed laser system for LIDAR and ranging applications, which make use of the latest...

  17. Microstructured fibers for high power applications

    Science.gov (United States)

    Baggett, J. C.; Petrovich, M. N.; Hayes, J. R.; Finazzi, V.; Poletti, F.; Amezcua, R.; Broderick, N. G. R.; Richardson, D. J.; Monro, T. M.; Salter, P. L.; Proudley, G.; O'Driscoll, E. J.

    2005-10-01

    Fiber delivery of intense laser radiation is important for a broad range of application sectors, from medicine through to industrial laser processing of materials, and offers many practical system design and usage benefits relative to free space solutions. Optical fibers for high power transmission applications need to offer low optical nonlinearity and high damage thresholds. Single-mode guidance is also often a fundamental requirement for the many applications in which good beam quality is critical. In recent years, microstructured fiber technology has revolutionized the dynamic field of optical fibers, bringing with them a wide range of novel optical properties. These fibers, in which the cladding region is peppered with many small air holes, are separated into two distinct categories, defined by the way in which they guide light: (1) index-guiding holey fibers (HFs), in which the core is solid and light is guided by a modified form of total internal reflection, and (2) photonic band-gap fibers (PBGFs) in which guidance in a hollow core can be achieved via photonic band-gap effects. Both of these microstructured fiber types offer attractive qualities for beam delivery applications. For example, using HF technology, large-mode-area, pure silica fibers with robust single-mode guidance over broad wavelength ranges can be routinely fabricated. In addition, the ability to guide light in an air-core within PBGFs presents obvious power handling advantages. In this paper we review the fundamentals and current status of high power, high brightness, beam delivery in HFs and PBGFs, and speculate as to future prospects.

  18. Techniques for preventing damage to high power laser components

    Energy Technology Data Exchange (ETDEWEB)

    Stowers, I.F.; Patton, H.G.; Jones, W.A.; Wentworth, D.E.

    1977-09-01

    Techniques for preventing damage to components of the LASL Shiva high power laser system were briefly presented. Optical element damage in the disk amplifier from the combined fluence of the primary laser beam and the Xenon flash lamps that pump the cavity was discussed. Assembly and cleaning techniques were described which have improved optical element life by minimizing particulate and optically absorbing film contamination on assembled amplifier structures. A Class-100 vertical flaw clean room used for assembly and inspection of laser components was also described. The life of a disk amplifier was extended from less than 50 shots to 500 shots through application of these assembly and cleaning techniques. (RME)

  19. Highly-efficient high-power pumps for fiber lasers

    Science.gov (United States)

    Gapontsev, V.; Moshegov, N.; Berezin, I.; Komissarov, A.; Trubenko, P.; Miftakhutdinov, D.; Berishev, I.; Chuyanov, V.; Raisky, O.; Ovtchinnikov, A.

    2017-02-01

    We report on high efficiency multimode pumps that enable ultra-high efficiency high power ECO Fiber Lasers. We discuss chip and packaged pump design and performance. Peak out-of-fiber power efficiency of ECO Fiber Laser pumps was reported to be as high as 68% and was achieved with passive cooling. For applications that do not require Fiber Lasers with ultimate power efficiency, we have developed passively cooled pumps with out-of-fiber power efficiency greater than 50%, maintained at operating current up to 22A. We report on approaches to diode chip and packaged pump design that possess such performance.

  20. Reduced filamentation in high power semiconductor lasers

    DEFF Research Database (Denmark)

    Skovgaard, Peter M. W.; McInerney, John; O'Brien, Peter

    1999-01-01

    High brightness semiconductor lasers have applications in fields ranging from material processing to medicine. The main difficulty associated with high brightness is that high optical power densities cause damage to the laser facet and thus require large apertures. This, in turn, results in spatio...... in the optical field causes spatial hole-burning and thus filamentation. To reduce filamentation we propose a new, relatively simple design based on inhomogeneous pumping in which the injected current has a gradual transverse profile. We confirm the improved laser performance theoretically and experimentally...

  1. Hybrid high power femtosecond laser system

    Science.gov (United States)

    Trunov, V. I.; Petrov, V. V.; Pestryakov, E. V.; Kirpichnikov, A. V.

    2006-01-01

    Design of a high-power femtosecond laser system based on hybrid chirped pulse amplification (CPA) technique developed by us is presented. The goal of the hybrid principle is the use of the parametric and laser amplification methods in chirped pulse amplifiers. It makes it possible to amplify the low-cycle pulses with a duration of <= fs to terawatt power with a high contrast and high conversion efficiency of the pump radiation. In a created system the Ti:Sapphire laser with 10 fs pulses at 810 nm and output energy about 1-3 nJ will be used like seed source. The oscillator pulses were stretched to duration of about 500 ps by an all-reflective grating stretcher. Then the stretched pulses are injected into a nondegenerate noncollinear optical parametric amplifier (NOPA) on the two BBO crystals. After amplification in NOPA the residual pump was used in a bow-tie four pass amplifier with hybrid active medium (based on Al II0 3:Ti 3+ and BeAl IIO 4:Ti 3+ crystals). The final stage of the amplification system consists of two channels, namely NIR (820 nm) and short-VIS (410 nm). Numerical simulation has shown that the terawatt level of output power can be achieved also in a short-VIS channel at the pumping of the double-crystal BBO NOPA by the radiation of the fourth harmonic of the Nd:YAG laser at 266 nm. Experimentally parametric amplification in BBO crystals of 30-50 fs pulses were investigated and optimized using SPIDER technique and single-shot autocomelator for the realization of shortest duration 40 fs.

  2. High-power thulium lasers on a silicon photonics platform.

    Science.gov (United States)

    Li, Nanxi; Purnawirman, P; Su, Zhan; Salih Magden, E; Callahan, Patrick T; Shtyrkova, Katia; Xin, Ming; Ruocco, Alfonso; Baiocco, Christopher; Ippen, Erich P; Kärtner, Franz X; Bradley, Jonathan D B; Vermeulen, Diedrik; Watts, Michael R

    2017-03-15

    Mid-infrared laser sources are of great interest for various applications, including light detection and ranging, spectroscopy, communication, trace-gas detection, and medical sensing. Silicon photonics is a promising platform that enables these applications to be integrated on a single chip with low cost and compact size. Silicon-based high-power lasers have been demonstrated at 1.55 μm wavelength, while in the 2 μm region, to the best of our knowledge, high-power, high-efficiency, and monolithic light sources have been minimally investigated. In this Letter, we report on high-power CMOS-compatible thulium-doped distributed feedback and distributed Bragg reflector lasers with single-mode output powers up to 267 and 387 mW, and slope efficiencies of 14% and 23%, respectively. More than 70 dB side-mode suppression ratio is achieved for both lasers. This work extends the applicability of silicon photonic microsystems in the 2 μm region.

  3. High power infrared QCLs: advances and applications

    Science.gov (United States)

    Patel, C. Kumar N.

    2012-01-01

    QCLs are becoming the most important sources of laser radiation in the midwave infrared (MWIR) and longwave infrared (LWIR) regions because of their size, weight, power and reliability advantages over other laser sources in the same spectral regions. The availability of multiwatt RT operation QCLs from 3.5 μm to >16 μm with wall plug efficiency of 10% or higher is hastening the replacement of traditional sources such as OPOs and OPSELs in many applications. QCLs can replace CO2 lasers in many low power applications. Of the two leading groups in improvements in QCL performance, Pranalytica is the commercial organization that has been supplying the highest performance QCLs to various customers for over four year. Using a new QCL design concept, the non-resonant extraction [1], we have achieved CW/RT power of >4.7 W and WPE of >17% in the 4.4 μm - 5.0 μm region. In the LWIR region, we have recently demonstrated QCLs with CW/RT power exceeding 1 W with WPE of nearly 10 % in the 7.0 μm-10.0 μm region. In general, the high power CW/RT operation requires use of TECs to maintain QCLs at appropriate operating temperatures. However, TECs consume additional electrical power, which is not desirable for handheld, battery-operated applications, where system power conversion efficiency is more important than just the QCL chip level power conversion efficiency. In high duty cycle pulsed (quasi-CW) mode, the QCLs can be operated without TECs and have produced nearly the same average power as that available in CW mode with TECs. Multiwatt average powers are obtained even in ambient T>70°C, with true efficiency of electrical power-to-optical power conversion being above 10%. Because of the availability of QCLs with multiwatt power outputs and wavelength range covering a spectral region from ~3.5 μm to >16 μm, the QCLs have found instantaneous acceptance for insertion into multitude of defense and homeland security applications, including laser sources for infrared

  4. High power parallel ultrashort pulse laser processing

    Science.gov (United States)

    Gillner, Arnold; Gretzki, Patrick; Büsing, Lasse

    2016-03-01

    The class of ultra-short-pulse (USP) laser sources are used, whenever high precession and high quality material processing is demanded. These laser sources deliver pulse duration in the range of ps to fs and are characterized with high peak intensities leading to a direct vaporization of the material with a minimum thermal damage. With the availability of industrial laser source with an average power of up to 1000W, the main challenge consist of the effective energy distribution and disposition. Using lasers with high repetition rates in the MHz region can cause thermal issues like overheating, melt production and low ablation quality. In this paper, we will discuss different approaches for multibeam processing for utilization of high pulse energies. The combination of diffractive optics and conventional galvometer scanner can be used for high throughput laser ablation, but are limited in the optical qualities. We will show which applications can benefit from this hybrid optic and which improvements in productivity are expected. In addition, the optical limitations of the system will be compiled, in order to evaluate the suitability of this approach for any given application.

  5. A theoretical investigation of the laser damage threshold of metal multi-dielectric mirrors for high power ultrashort applications.

    Science.gov (United States)

    Wang, Bin; Gallais, Laurent

    2013-06-17

    An approach for the theoretical evaluation of the damage threshold in optical interference coatings that combine metal and dielectric films is presented. The model that is used combines a matrix formalism to describe the film system with the two temperatures model that describes the energy transfer and the temperatures of electrons and lattice in a solid submitted to a laser irradiation at the femtosecond time scale. With this approach the thermal consequences due to the ultrafast absorption of the metal film can be evaluated in the multilayer stack for single or multiple pulses. Some applications are presented for the case of broadband mirrors for ultrashort pulses with low dispersion. Particularly we study the impact of the metal film (metal element, thickness) and the design on the Laser Induced Damage Threshold in the sub picosecond regime.

  6. Atmospheric propagation and combining of high power lasers: comment.

    Science.gov (United States)

    Goodno, Gregory D; Rothenberg, Joshua E

    2016-10-10

    Nelson et al. [Appl. Opt.55, 1757 (2016)APOPAI0003-693510.1364/AO.55.001757] recently concluded that coherent beam combining and remote phase locking of high-power lasers are fundamentally limited by the laser source linewidth. These conclusions are incorrect and not relevant to practical high-power coherently combined laser architectures.

  7. Atmospheric Propagation and Combining of High-Power Lasers

    Science.gov (United States)

    2015-09-08

    Naval Research Laboratory Washington, DC 20375-5320 NRL/MR/6703--15-9646 Atmospheric Propagation and Combining of High-Power Lasers W. NelsoN...ABSTRACT c. THIS PAGE 18. NUMBER OF PAGES 17. LIMITATION OF ABSTRACT Atmospheric Propagation and Combining of High-Power Lasers W. Nelson,* P. Sprangle...Turbulence Beam combining In this paper we analyze the beam combining and atmospheric propagation of high-power lasers for directed-energy (DE

  8. Active beam integrator for high power coherent lasers

    Energy Technology Data Exchange (ETDEWEB)

    Laguarta, F.; Armengol, J.; Vega, F.; Lupon, N. [Univ. Politecnica de Catalunya, Terrassa (Spain). Dept. d`Optica i Optometria

    1996-12-31

    In laser materials processing applications it is often necessary to work with uniform intensity distributions. This goal is quite difficult to achieve when dealing with high power laser beams, and becomes critical for a successful application involving surface heat treatment of non-metallic materials. The authors have designed and tested a very simple beam shaper for transforming the initial intensity distribution of a CO{sub 2} laser beam mode into a more uniform intensity profile. The beam shaper is a two-faceted mirror for active integration of high power coherent laser beams. After reflection in the faceted mirror, a TEM00 or TEM01 CO{sub 2} laser beam is divided into two beamlets that overlap to give a more uniform intensity distribution. A sharp interference pattern due to the high spatial coherence of the incident beam appears. This interference pattern is actively integrated by a high-frequency longitudinal displacement of one of the facets. This provides a change in the relative phase of the two beamlets, and consequently the interference pattern vibrates and its contribution to the intensity distribution averages out. When sweeping this distribution over a sample, a uniform amount of energy is deposited at every point of its surface. It must be emphasized that unlike multifaceted mirrors, the two-facet integrator may provide uniform intensity profiles over any working distance. Finally, as in other integration devices an imaging system may be used to obtain a spot of the shape and the size desired for a particular application.

  9. Spatial and Spectral Brightness Enhancement of High Power Semiconductor Lasers

    Science.gov (United States)

    Leidner, Jordan Palmer

    The performance of high-power broad-area diode lasers is inhibited by beam filamentation induced by free-carrier-based self-focusing. The resulting beam degradation limits their usage in high-brightness, high-power applications such as pumping fiber lasers, and laser cutting, welding, or marking. Finite-difference propagation method simulations via RSoft's BeamPROP commercial simulation suite and a custom-built MATLAB code were used for the study and design of laser cavities that suppress or avoid filamentation. BeamPROP was used to design a tapered, passive, multi-mode interference cavity for the creation of a self-phase-locking laser array, which is comprised of many single-mode gain elements coupled to a wide output coupler to avoid damage from local high optical intensities. MATLAB simulations were used to study the effects of longitudinal and lateral cavity confinement on lateral beam quality in conventional broad-area lasers. This simulation was expanded to design a laser with lateral gain and index prescription that is predicted to operate at or above state-of-the-art powers while being efficiently coupled to conventional telecom single-mode optical fibers. Experimentally, a commercial broad-area laser was coupled in the far-field to a single-mode fiber Bragg grating to provide grating-stabilized single-mode laser feedback resulting in measured spectral narrowing for efficient pump absorption. Additionally a 19 GHz-span, spatially resolved, self-heterodyne measurement was made of a broad-area laser to study the evolution/devolution of the mode content of the emitted laser beam with increasing power levels.

  10. Final Report: High Power Semiconductor Laser Sources,

    Science.gov (United States)

    1989-01-01

    m(I mO (26a) Here a is a dimensionless quantity related to the ratio be- 2 tween pump and field intensities, and in our model, is 0, = bxo tanh (xo...and E. Kapon. "Application of the equivalent index bxo 6b method to DH diode lasers," Appl. Opt.. vol. 18. no. 22. pp. 3724- 3725. 1979. While 0,1

  11. High-power laser source evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Back, C.A.; Decker, C.D.; Dipeso, G.J.; Gerassimenko, M.; Managan, R.A.; Serduke, F.J.D.; Simonson, G.F.; Suter, L.J.

    1997-07-01

    This document reports progress in these areas: EXPERIMENTAL RESULTS FROM NOVA: TAMPED XENON UNDERDENSE X-RAY EMITTERS; MODELING MULTI-KEV RADIATION PRODUCTION OF XENON-FILLED BERYLLIUM CANS; MAPPING A CALCULATION FROM LASNEX TO CALE; HOT X RAYS FROM SEEDED NIF CAPSULES; HOHLRAUM DEBRIS MEASUREMENTS AT NOVA; FOAM AND STRUCTURAL RESPONSE CALCULATIONS FOR NIF NEUTRON EXPOSURE SAMPLE CASE ASSEMBLY DESIGN; NON-IGNITION X-RAY SOURCE FLUENCE-AREA PRODUCTS FOR NUCLEAR EFFECTS TESTING ON NIF. Also appended are reprints of two papers. The first is on the subject of ``X-Ray Production in Laser-Heated Xe Gas Targets.`` The second is on ``Efficient Production and Applications of 2- to 10-keV X Rays by Laser-Heated Underdense Radiators.``

  12. Nuclear Science and Applications with the Next Generation of High-Power Lasers and Brilliant Low-Energy Gamma Beams at ELI-NP

    Science.gov (United States)

    Gales, S.

    2015-11-01

    The development of high-power lasers and the combination of such novel devices with accelerator technology has enlarged the science reach of many research fields, in particular high-energy nuclear physics and astrophysics, as well as societal applications in material science, nuclear energy and medicine. The European Strategic Forum for Research Infrastructures (ESFRI) has selected a proposal based on these new premises called "ELI" for Extreme Light Infrastructure. ELI will be built as a network of three complementary pillars at the frontier of laser technologies. The ELI-NP pillar (NP for nuclear physics) is under construction near Bucharest (Romania) and will develop a scientific program using two 10-PW lasers and a Compton back-scattering high-brilliance and intense low-energy gamma beam, a marriage of laser and accelerator technology at the frontier of knowledge. In the present paper, the technical description of the facility, the present status of the project as well as the science, applications and future perspectives will be discussed.

  13. High power laser workover and completion tools and systems

    Science.gov (United States)

    Zediker, Mark S; Rinzler, Charles C; Faircloth, Brian O; Koblick, Yeshaya; Moxley, Joel F

    2014-10-28

    Workover and completion systems, devices and methods for utilizing 10 kW or more laser energy transmitted deep into the earth with the suppression of associated nonlinear phenomena. Systems and devices for the laser workover and completion of a borehole in the earth. These systems and devices can deliver high power laser energy down a deep borehole, while maintaining the high power to perform laser workover and completion operations in such boreholes deep within the earth.

  14. Improved cutting performance in high power laser cutting

    DEFF Research Database (Denmark)

    Olsen, Flemming Ove

    2003-01-01

    Recent results in high power laser cutting especially with focus on cutting of mild grade steel types for shipbuilding are described.......Recent results in high power laser cutting especially with focus on cutting of mild grade steel types for shipbuilding are described....

  15. Improved cutting performance in high power laser cutting

    DEFF Research Database (Denmark)

    Olsen, Flemming Ove

    2003-01-01

    Recent results in high power laser cutting especially with focus on cutting of mild grade steel types for shipbuilding are described.......Recent results in high power laser cutting especially with focus on cutting of mild grade steel types for shipbuilding are described....

  16. High-Power Lasers for Science and Society

    Energy Technology Data Exchange (ETDEWEB)

    Siders, C. W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Haefner, C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2016-10-05

    Since the first demonstration of the laser in 1960 by Theodore Maiman at Hughes Research Laboratories, the principal defining characteristic of lasers has been their ability to focus unprecedented powers of light in space, time, and frequency. High-power lasers have, over the ensuing five and a half decades, illuminated entirely new fields of scientific endeavor as well as made a profound impact on society. While the United States pioneered lasers and their early applications, we have been eclipsed in the past decade by highly effective national and international networks in both Europe and Asia, which have effectively focused their energies, efforts, and resources to achieve greater scientific and societal impact. This white paper calls for strategic investment which, by striking an appropriate balance between distributing our precious national funds and establishing centers of excellence, will ensure a broad pipeline of people and transformative ideas connecting our world-leading universities, defining flagship facilities stewarded by our national laboratories, and driving innovation across industry, to fully exploit the potential of high-power lasers.

  17. Recent results in mirror based high power laser cutting

    DEFF Research Database (Denmark)

    Olsen, Flemming Ove; Nielsen, Jakob Skov; Elvang, Mads

    2004-01-01

    In this paper, recent results in high power laser cutting, obtained in reseach and development projects are presented. Two types of mirror based focussing systems for laser cutting have been developed and applied in laser cutting studies on CO2-lasers up to 12 kW. In shipyard environment cutting...

  18. High power laser downhole cutting tools and systems

    Energy Technology Data Exchange (ETDEWEB)

    Zediker, Mark S; Rinzler, Charles C; Faircloth, Brian O; Koblick, Yeshaya; Moxley, Joel F

    2015-01-20

    Downhole cutting systems, devices and methods for utilizing 10 kW or more laser energy transmitted deep into the earth with the suppression of associated nonlinear phenomena. Systems and devices for the laser cutting operations within a borehole in the earth. These systems and devices can deliver high power laser energy down a deep borehole, while maintaining the high power to perform cutting operations in such boreholes deep within the earth.

  19. Development of a high power femtosecond laser

    CSIR Research Space (South Africa)

    Neethling, PH

    2010-10-01

    Full Text Available the pulses from the Coherent Mira/BMI amplified femtosecond laser at the LRI. Ideally the OPCPA stage should be pumped by a 100 ? 300 ps laser with tens of mJ pulse energy, matching the stretched pulse duration. This laser will be developed by the CSIR...

  20. Germanate Glass Fiber Lasers for High Power

    Science.gov (United States)

    2016-01-04

    evidence of crystallisation after thermal cycling, and is of a low enough loss to realize a fiber laser. The glass stability is demonstrated by...2low-loss fiber can be realized . 15. SUBJECT TERMS Germanate fiber Laser, Fiber Laser, Structured Fiber 16. SECURITY CLASSIFICATION OF: 17. LIMITATION...the profile of bare fibres and the loss value at 630 matches with the spot loss measurement done by Naveed. DISTRIBUTION A: Distribution

  1. Dimensional characteristics of welds performed on AISI 1045 steel by means of the application of high power diode laser; Caracteristicas dimensionales de soldadura formadas sobre el acero AISI 1045 mediante la aplicacion del laser diodo de alta potencia

    Energy Technology Data Exchange (ETDEWEB)

    Sanchez-Castillo, A.; Pou, J.; Lusquinos, F.; Quintero, F.; Soto, R.; Boutinguiza, M.; Saavedra, M.; Perez-Amor, M.

    2004-07-01

    The named High Power diode Laser (HPDL), emits a beam of optical energy generated by diode stimulation and offers the capability of supplying levels of power up to 6 kW. The objective of this research work was to study the main welding variables and their effects on dimensional characteristics of the beads performed by means of application of this novel laser. The results obtained, show that HPDL, is an energy source able to perform welds on AISI 1045 steel plates under conduction mode, without any kind of mechanized preparation, preheating or post-weld treatment and, without filler metal application. (Author) 16 refs.

  2. In-situ strain observation in high power laser cladding

    OpenAIRE

    Ocelik, V.; Bosgra, J.; De Hosson, J. Th. M.

    2009-01-01

    The modern experimental technique - so called Digital Image Correlation - is applied during high power laser surface treatments for in-situ observation of displacements and strains near the processing area during and a short time after laser processing. An experimental setup has been designed and tested to measure in-situ the strain during treatment with a high power 2 kW CW Nd:YAG laser, i.e. laser hardening, surface remelting, and laser cladding with Nanosteel, Eutroloy 16012 and MicroMelt ...

  3. Vacuum Window Design for High-Power Lasers

    CERN Document Server

    Shaftan, T V

    2005-01-01

    One of the problems in the high-power lasers design is in outcoupling of a powerful laser beam out of a vacuum volume into atmosphere. Usually the laser device is located inside a vacuum tank. The laser radiation is transported to the outside world through the transparent vacuum window. While considered transparent, some of the light passing through the glass is absorbed and converted to heat. For most applications, these properties are academic curiosities; however, in multi-kilowatt lasers, the heat becomes significant and can lead to a failure. The absorbed power can result in thermal stress, reduction of light transmission and, consequently, window damage. Modern optical technology has developed different types of glass (Silica, BK7, diamond, etc.) that have high thermal conductivity and damage threshold. However, for kilo- and megawatt lasers the issue still remains open. In this paper we present a solution that may relieve the heat load on the output window. We discuss advantages and issues of this part...

  4. Rapid heating of matter using high power lasers

    Energy Technology Data Exchange (ETDEWEB)

    Bang, Woosuk [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-04-08

    This slide presentation describes motivation (uniform and rapid heating of a target, opportunity to study warm dense matter, study of nuclear fusion reactions), rapid heating of matter with intense laser-driven ion beams, visualization of the expanding warm dense gold and diamond, and nuclear fusion experiments using high power lasers (direct heating of deuterium spheres (radius ~ 10nm) with an intense laser pulse.

  5. Design and characterization of Yb and Nd doped transparent ceramics for high power laser applications: recent advancements

    Science.gov (United States)

    Lapucci, A.; Vannini, M.; Ciofini, M.; Pirri, A.; Nikl, M.; Li, J.; Esposito, L.; Biasini, V.; Hostasa, J.; Goto, T.; Boulon, G.; Maksimov, R.; Gizzi, L.; Labate, L.; Toci, G.

    2017-01-01

    We report a review on our recent developments in Yttebium and Neodymium doped laser ceramics, along two main research lines. The first is the design and development of Yb:YAG ceramics with non uniform doping distribution, for the management of thermo-mechanical stresses and for the mitigation of ASE: layered structures have been produced by solid state reactive sintering, using different forming processes (spray drying and cold press of the homogenized powders, tape cast of the slurry); samples have been characterized and compared to FEM analysis. The second is the investigation of Lutetium based ceramics (such as mixed garnets LuYAG and Lu2O3); this interest is mainly motivated by the favorable thermal properties of these hosts under high doping. We recently obtained for the first time high efficiency laser emission from Yb doped LuYAG ceramics. The investigation on sesquioxides has been focused on Nddoped Lu2O3 ceramics, fabricated with the Spark Plasma Sintering method (SPS). We recently achieved the first laser emission above 1 W from Nd doped Lu2O3 ceramics fabricated by SPS.

  6. Cryogenic cooling for high power laser amplifiers

    Directory of Open Access Journals (Sweden)

    Perin J.P.

    2013-11-01

    Full Text Available Using DPSSL (Diode Pumped Solid State Lasers as pumping technology, PW-class lasers with enhanced repetition rates are developed. Each of the Yb YAG amplifiers will be diode-pumped at a wavelength of 940 nm. This is a prerequisite for achieving high repetition rates (light amplification duration 1 millisecond and repetition rate 10 Hz. The efficiency of DPSSL is inversely proportional to the temperature, for this reason the slab amplifier have to be cooled at a temperature in the range of 100 K–170 K with a heat flux of 1 MW*m−2. This paper describes the thermo-mechanical analysis for the design of the amplification laser head, presents a preliminary proposal for the required cryogenic cooling system and finally outlines the gain of cryogenic operation for the efficiency of high pulsed laser.

  7. High-Power Solid-State Lasers from a Laser Glass Perspective

    Energy Technology Data Exchange (ETDEWEB)

    Campbell, J H; Hayden, J S; Marker, A J

    2010-12-17

    Advances in laser glass compositions and manufacturing have enabled a new class of high-energy/high-power (HEHP), petawatt (PW) and high-average-power (HAP) laser systems that are being used for fusion energy ignition demonstration, fundamental physics research and materials processing, respectively. The requirements for these three laser systems are different necessitating different glasses or groups of glasses. The manufacturing technology is now mature for melting, annealing, fabricating and finishing of laser glasses for all three applications. The laser glass properties of major importance for HEHP, PW and HAP applications are briefly reviewed and the compositions and properties of the most widely used commercial laser glasses summarized. Proposed advances in these three laser systems will require new glasses and new melting methods which are briefly discussed. The challenges presented by these laser systems will likely dominate the field of laser glass development over the next several decades.

  8. High power pump laser diodes for 2μm fibre laser

    Science.gov (United States)

    Pawlik, S.; Todt, R.; Moser, M.; Romero, O.; Lichtenstein, N.

    2014-03-01

    We report on our recent developments at II-VI Laser Enterprise of laser diode sources for the 79x nm range. High power conversion efficiency in excess of 62% was demonstrated. For high power applications like Thulium fiber laser pumping we have achieved an output power of more than 12.5W in CW operation for 94 μm wide broad-area single-emitters. We added the functionality of wavelength stabilization to the laser diodes by using a distributed feedback grating (DFB). Locking has been obtained over the full current range between 1A and 4A tested so far with some margin for temperature variation. For efficient fiber laser pumping the laser diodes were integrated in a multi-emitter platform, achieving 38 W out of a 105 μm fiber within 0.15 NA.

  9. High Power Photonic Crystal Fibre Raman Laser

    Institute of Scientific and Technical Information of China (English)

    YAN Pei-Guang; RUAN Shuang-Chen; YU Yong-Qin; GUO Chun-Yu; GUO Yuan; LIU Cheng-Xiang

    2006-01-01

    A cw Raman laser based on a 100-m photonic crystal fibre is demonstrated with up to 3.8 W output power at the incident pump power of 12 W, corresponding to an optical-to-optical efficiency of about 31.6%. The second order Stokes light, which is firstly reported in a cw photonic crystal fibre Raman laser, is obtained at 1183nm with an output power of 1.6 W and a slope efficiency of about 45.7%.

  10. Simulation of High Power Lasers (Preprint)

    Science.gov (United States)

    2010-06-01

    product of laser power. 5. References 1 Wilcox, D. C, Turbulence Modeling for CFD, DCW Industries, Inc. pp. 185-193, July 1998. 2 Menter, F. L...Modeling for CFD, DCW Industries, Inc. pp. 294-296, July 1998. 4 Perram, G. P, .Int. J. Chem. Kinet. 27, 817-28 (1995). 5 Madden, T. J. and Solomon

  11. Supplemental Task-High Power Lasers

    Science.gov (United States)

    2011-12-20

    Bragg reflector ( DBR ) on the bottom. The development of the VECSELs was delayed during this year due to the installation process for the AFOSR DURIP...O and Lester L F Analytical Modeling of the Temperature Performance of Monolithic Passively Mode-Locked Quantum Dot Lasers J. Quantum Electron. 47

  12. High-power atomic xenon laser

    NARCIS (Netherlands)

    Witteman, W.J.; Peters, P.J.M.; Botma, H.; Botma, H.; Tskhai, S.N.; Udalov, Yu.B.; Mei, Q.C.; Mei, Qi-Chu; Ochkin, V.N.

    1995-01-01

    The high pressure atomic xenon laser is becoming the most promising light source in the wavelength region of a few microns. The merits are high efficiency (so far up to 8 percent), high output energies (15 J/liter at 9 bar), high continuous output power (more than 200 W/liter), no gas dissociation a

  13. Recent results in mirror based high power laser cutting

    DEFF Research Database (Denmark)

    Olsen, Flemming Ove; Nielsen, Jakob Skov; Elvang, Mads

    2004-01-01

    In this paper, recent results in high power laser cutting, obtained in reseach and development projects are presented. Two types of mirror based focussing systems for laser cutting have been developed and applied in laser cutting studies on CO2-lasers up to 12 kW. In shipyard environment cutting...... speed increase relative to state-of-the-art cutting of over 100 % has been achieved....

  14. In-situ strain observation in high power laser cladding

    NARCIS (Netherlands)

    Ocelik, V.; Bosgra, J.; de Hosson, J. Th. M.

    2009-01-01

    The modern experimental technique - so called Digital Image Correlation - is applied during high power laser surface treatments for in-situ observation of displacements and strains near the processing area during and a short time after laser processing. An experimental setup has been designed and

  15. Functionally graded materials produced with high power lasers

    NARCIS (Netherlands)

    De Hosson, JTM; Ocelík, Vašek; Chandra, T; Torralba, JM; Sakai, T

    2003-01-01

    In this keynote paper two examples will be present of functionally graded materials produced with high power Nd:YAG lasers. In particular the conditions for a successful Laser Melt Injection (LMI) of SiC and WC particles into the melt pool of A18Si and Ti6Al4V alloys are presented. The formation of

  16. In-situ strain observation in high power laser cladding

    NARCIS (Netherlands)

    Ocelik, V.; Bosgra, J.; de Hosson, J. Th. M.

    2009-01-01

    The modern experimental technique - so called Digital Image Correlation - is applied during high power laser surface treatments for in-situ observation of displacements and strains near the processing area during and a short time after laser processing. An experimental setup has been designed and te

  17. In-situ strain observation in high power laser cladding

    NARCIS (Netherlands)

    Ocelik, V.; Bosgra, J.; de Hosson, J. Th. M.

    2009-01-01

    The modern experimental technique - so called Digital Image Correlation - is applied during high power laser surface treatments for in-situ observation of displacements and strains near the processing area during and a short time after laser processing. An experimental setup has been designed and te

  18. High power laser-matter interaction

    CERN Document Server

    Mulser, Peter

    2010-01-01

    This book intended as a guide for scientists and students who have just discovered the field as a new and attractive area of research, and for scientists who have worked in another field and want to join now the subject of laser plasmas. In the first chapter the plasma dynamics is described phenomenologically by a two fluid model and similarity relations from dimensional analysis. Chapter 2 is devoted to plasma optics and collisional absorption in the dielectric and ballistic model. Linear resonance absorption at the plasma frequency and its mild nonlinearities as well as the self-quenching of high amplitude electron plasma waves by wave breaking are discussed in Chapter 3. With increasing laser intensity the plasma dynamics is dominated by radiation pressure, at resonance producing all kinds of parametric instabilities and out of resonance leading to density steps, self-focusing and filamentation, described in Chapters 4 and 5. A self-contained treatment of field ionization of atoms and related phenomena ar...

  19. High-power laser source evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Back, C. A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Decker, C. D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Davis, J. F. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Dixit, S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Grun, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Managan, R. A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Serduke, F. J. D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Simonson, G. F. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Suter, L. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Wuest, C. R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Ze, F. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    1998-07-01

    Robust Nuclear-Weapons-Effects Testing (NWET) capability will be needed for the foreseeable future to ensure the performance and reliability, in nuclear environments, of the evolving U.S. stockpile of weapons and other assets. Ongoing research on the use of high-energy lasers to generate environments of utility in nuclear weapon radiation effects simulations is addressed in the work described in this report. Laser-driven hohlraums and a variety of other targets have been considered in an effort to develop NWET capability of the highest possible fidelity in above-ground experiments. The envelope of large-system test needs is shown as the gray region in fig. 1. It does not represent the spectrum of any device; it is just the envelope of the spectral region of outputs from a number of possible devices. It is a goal of our laser-only and ignition-capsule source development work to generate x rays that fall somewhere in this envelope. One of the earlier appearances of this envelope is in ref. 1. The Defense Special Weapons Agency provided important support for the work described herein. A total of $520K was provided in the 1997 IACROs 97-3022 for Source Development and 97-3048 for Facilitization. The period of performance specified in the Statement of Work ran from 28 February 1997 until 30 November 1997. This period was extended, by agreement with DSWA, for two reasons: 1) despite the stated period of performance, funds were not available at LLNL to begin this work until somewhat later in the fiscal year, and 2) we agreed to stretch the current resources until follow-on funds were in hand, to minimize effects of ramping down and up again. The tasks addressed in this report are the following: 1) Non-ignition-source model benchmarking and design. This involves analysis of existing and new data on laser-only sources to benchmark LASNEX predictions 2) Non-ignition-source development experiments 3) Ignition capsule design to improve total x-ray output and simplify target

  20. High-power laser source evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Back, C. A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Decker, C. D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Davis, J. F. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Dixit, S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Grun, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Managan, R. A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Serduke, F. J. D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Simonson, G. F. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Suter, L. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Wuest, C. R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Ze, F. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    1998-07-01

    Robust Nuclear-Weapons-Effects Testing (NWET) capability will be needed for the foreseeable future to ensure the performance and reliability, in nuclear environments, of the evolving U.S. stockpile of weapons and other assets. Ongoing research on the use of high-energy lasers to generate environments of utility in nuclear weapon radiation effects simulations is addressed in the work described in this report. Laser-driven hohlraums and a variety of other targets have been considered in an effort to develop NWET capability of the highest possible fidelity in above-ground experiments. The envelope of large-system test needs is shown as the gray region in fig. 1. It does not represent the spectrum of any device; it is just the envelope of the spectral region of outputs from a number of possible devices. It is a goal of our laser-only and ignition-capsule source development work to generate x rays that fall somewhere in this envelope. One of the earlier appearances of this envelope is in ref. 1. The Defense Special Weapons Agency provided important support for the work described herein. A total of $520K was provided in the 1997 IACROs 97-3022 for Source Development and 97-3048 for Facilitization. The period of performance specified in the Statement of Work ran from 28 February 1997 until 30 November 1997. This period was extended, by agreement with DSWA, for two reasons: 1) despite the stated period of performance, funds were not available at LLNL to begin this work until somewhat later in the fiscal year, and 2) we agreed to stretch the current resources until follow-on funds were in hand, to minimize effects of ramping down and up again. The tasks addressed in this report are the following: 1) Non-ignition-source model benchmarking and design. This involves analysis of existing and new data on laser-only sources to benchmark LASNEX predictions 2) Non-ignition-source development experiments 3) Ignition capsule design to improve total x-ray output and simplify target

  1. High power solid state laser modulator

    Science.gov (United States)

    Birx, Daniel L.; Ball, Don G.; Cook, Edward G.

    2004-04-27

    A multi-stage magnetic modulator provides a pulse train of .+-.40 kV electrical pulses at a 5-7 kHz repetition rate to a metal vapor laser. A fractional turn transformer steps up the voltage by a factor of 80 to 1 and magnetic pulse compression is used to reduce the pulse width of the pulse train. The transformer is fabricated utilizing a rod and plate stack type of construction to achieve a high packing factor. The pulses are controlled by an SCR stack where a plurality of SCRs are electrically connected in parallel, each SCR electrically connected to a saturable inductor, all saturable inductors being wound on the same core of magnetic material for enhanced power handling characteristics.

  2. Laser Cooled High-Power Fiber Amplifier

    CERN Document Server

    Nemova, Galina

    2009-01-01

    A theoretical model for laser cooled continuous-wave fiber amplifier is presented. The amplification process takes place in the Tm3+-doped core of the fluoride ZBLAN (ZrF4-BaF2-LaF3-AlF3-NaF) glass fiber. The cooling process takes place in the Yb3+:ZBLAN fiber cladding. It is shown that for each value of the pump power and the amplified signal there is a distribution of the concentration of the Tm3+ along the length of the fiber amplifier, which provides its athermal operation. The influence of a small deviation in the value of the amplified signal on the temperature of the fiber with the fixed distribution of the Tm3+ions in the fiber cladding is investigated.

  3. Design of deformable mirrors for high power lasers

    Institute of Scientific and Technical Information of China (English)

    Stefano Bonora; Jan Pilar; Antonio Lucianetti; Tomas Mocek

    2016-01-01

    We present the workflow of the design, realization and testing of deformable mirrors suitable for high power diode pumped solid-state lasers. It starts with the study of the aberration to be corrected, and then it continues with the design of the actuators position and characteristic. In this paper, we present and compare three deformable mirrors realized for multi-J level laser facilities. We show that with the same design concept it is possible to realize deformable mirrors for other types of lasers. As an example, we report the realization of a deformable mirror for femtosecond lasers and for a CW CO2 laser.

  4. Silver based batteries for high power applications

    Science.gov (United States)

    Karpinski, A. P.; Russell, S. J.; Serenyi, J. R.; Murphy, J. P.

    The present status of silver oxide-zinc technology and applications has been described by Karpinski et al. [A.P. Karpinski, B. Makovetski, S.J. Russell, J.R. Serenyi, D.C. Williams, Silver-Zinc: status of technology and applications, Journal of Power Sources, 80 (1999) 53-60], where the silver-zinc couple is still the preferred choice where high specific energy/energy density, coupled with high specific power/power density are important for high-rate, weight or size/configuration sensitive applications. Perhaps the silver oxide cathode can be considered one of the most versatile electrode materials. When coupled with other anodes and corresponding electrolyte management system, the silver electrode provides for a wide array of electrochemical systems that can be tailored to meet the most demanding, high power requirements. Besides zinc, the most notable include cadmium, iron, metal hydride, and hydrogen electrode for secondary systems, while primary systems include lithium and aluminum. Alloys including silver are also available, such as silver chloride, which when coupled with magnesium or aluminum are primarily used in many seawater applications. The selection and use of these couples is normally the result of a trade-off of many factors. These include performance, safety, risk, reliability, and cost. When high power is required, silver oxide-zinc, silver oxide-aluminum, and silver oxide-lithium are the most energetic. For moderate performance (i.e., lower power), silver oxide-zinc or silver-cadmium would be the system of choice. This paper summarizes the suitability of the silver-based couples, with an emphasis on the silver-zinc system, as primary or rechargeable power sources for high energy/power applications.

  5. Tunable high-power blue external cavity semiconductor laser

    Science.gov (United States)

    Ding, Ding; Lv, Xueqin; Chen, Xinyi; Wang, Fei; Zhang, Jiangyong; Che, Kaijun

    2017-09-01

    A commercially available high-power GaN-based blue laser diode has been operated in a simple Littrow-type external cavity (EC). Two kinds of EC configurations with the grating lines perpendicular (A configuration) and parallel (B configuration) to the p-n junction are evaluated. Good performance has been demonstrated for the EC laser with B configuration due to the better mode selection effect induced by the narrow feedback wavelength range from the grating. Under an injection current of 1100 mA, the spectral linewidth is narrowed significantly down to ∼0.1 nm from ∼1 nm (the free-running width), with a good wavelength-locking behavior and a higher than 35 dB-amplified spontaneous emission suppression ratio. Moreover, a tuning bandwidth of 3.6 nm from 443.9 nm to 447.5 nm is realized with output power of 1.24 W and EC coupling efficiency of 80% at the central wavelength. The grating-coupled blue EC laser with narrow spectral linewidth, flexible wavelength tunability, and high output power shows potential applications in atom cooling and trapping, high-resolution spectroscopy, second harmonic generation, and high-capacity holographic data storage.

  6. Flyer acceleration experiments using high-power laser

    Directory of Open Access Journals (Sweden)

    Kadono T.

    2013-11-01

    Full Text Available Flyer acceleration technique using high-power lasers has several advantages such as the achieved velocities higher than 10 km/s and non-contamination to the products generated by impacts. In this study, we show that a high-power laser can achieve flyer velocities higher than 10 km/s up to 60 km/s using spherical projectiles with a diameter of 0.1 − 0.3mm. We discuss the projectile condition during the flight based on the results of numerical simulations.

  7. High-power fiber laser welding and its application to metallic glass Zr{sub 55}Al{sub 10}Ni{sub 5}Cu{sub 30}

    Energy Technology Data Exchange (ETDEWEB)

    Kawahito, Yousuke [Joining and Welding Research Institute, Osaka University (JWRI), 11-1 Mihogaoka, Ibaraki, Osaka 567-0047 (Japan)], E-mail: kawahito@jwri.osaka-u.ac.jp; Terajima, Takeshi [Joining and Welding Research Institute, Osaka University (JWRI), 11-1 Mihogaoka, Ibaraki, Osaka 567-0047 (Japan); Kimura, Hisamich [Institute for Materials Research, Tohoku University (Japan); Kuroda, Toshio; Nakata, Kazuhiro; Katayama, Seiji [Joining and Welding Research Institute, Osaka University (JWRI), 11-1 Mihogaoka, Ibaraki, Osaka 567-0047 (Japan); Inoue, Akihisa [Institute for Materials Research, Tohoku University (Japan)

    2008-02-25

    Fiber laser has been receiving attention due to its advantages of high-power and high-beam quality to produce narrow and deep penetration welds at high-welding speeds. Therefore, fiber laser welding is expected to apply to the joining of metallic glass which has unique properties such as high-mechanical strength or small solidification shrinkage, because extremely rapid quenching for the laser weldment or heat-affected zone (HAZ) is possible to remain amorphous. In this research, fiber laser welding was first performed with the objective of obtaining a fundamental knowledge of weld property produced in bead-on-plate welding for common marital such as Type 304 stainless steel with 6 kW fiber laser beams of several peak power densities. Deeply penetrated weld beads with narrow widths were produced with small spots of tightly focused laser beams and full-penetration welds in 8 mm thick plate could be obtained at the high-welding speed of 4.5 m/min. Subsequently, the tightly focused 2.5 kW fiber laser beam was applied to 72 m/min ultra-high-speed welding for metallic glass Zr{sub 55}Al{sub 10}Ni{sub 5}Cu{sub 30} in order to keep amorphous metals. Consequently, the weldment and HAZ remained desirably amorphous at ultra-high-welding speed with a tightly focused fiber laser beam.

  8. High-power optically pumped semiconductor laser apllications

    Science.gov (United States)

    Morioka, S. Brandon

    2011-03-01

    OPS lasers have found applications in various industrial and scientific laser applications due to their power scaling capability, their wide range of emission wavelengths, physical size and their superior reliability. This paper provides an overview of commercially available OPS lasers and the applications in which they are used including biotechnology, medical, holography, Titanium-Sapphire laser pumping, non-lethal defense, forensics, and entertainment.

  9. Design and characterization of a novel power over fiber system integrating a high power diode laser

    Science.gov (United States)

    Perales, Mico; Yang, Mei-huan; Wu, Cheng-liang; Hsu, Chin-wei; Chao, Wei-sheng; Chen, Kun-hsein; Zahuranec, Terry

    2017-02-01

    High power 9xx nm diode lasers along with MH GoPower's (MHGP's) flexible line of Photovoltaic Power Converters (PPCs) are spurring high power applications for power over fiber (PoF), including applications for powering remote sensors and sensors monitoring high voltage equipment, powering high voltage IGBT gate drivers, converters used in RF over Fiber (RFoF) systems, and system power applications, including powering UAVs. In PoF, laser power is transmitted over fiber, and is converted to electricity by photovoltaic cells (packaged into Photovoltaic Power Converters, or PPCs) which efficiently convert the laser light. In this research, we design a high power multi-channel PoF system, incorporating a high power 976 nm diode laser, a cabling system with fiber break detection, and a multichannel PPC-module. We then characterizes system features such as its response time to system commands, the PPC module's electrical output stability, the PPC-module's thermal response, the fiber break detection system response, and the diode laser optical output stability. The high power PoF system and this research will serve as a scalable model for those interested in researching, developing, or deploying a high power, voltage isolated, and optically driven power source for high reliability utility, communications, defense, and scientific applications.

  10. High-Power ZBLAN Glass Fiber Lasers: Review and Prospect

    Directory of Open Access Journals (Sweden)

    Xiushan Zhu

    2010-01-01

    Full Text Available ZBLAN (ZrF4-BaF2-LaF3-AlF3-NaF, considered as the most stable heavy metal fluoride glass and the excellent host for rare-earth ions, has been extensively used for efficient and compact ultraviolet, visible, and infrared fiber lasers due to its low intrinsic loss, wide transparency window, and small phonon energy. In this paper, the historical progress and the properties of fluoride glasses and the fabrication of ZBLAN fibers are briefly described. Advances of infrared, upconversion, and supercontinuum ZBLAN fiber lasers are addressed in detail. Finally, constraints on the power scaling of ZBLAN fiber lasers are analyzed and discussed. ZBLAN fiber lasers are showing promise of generating high-power emissions covering from ultraviolet to mid-infrared considering the recent advances in newly designed optical fibers, beam-shaped high-power pump diodes, beam combining techniques, and heat-dissipating technology.

  11. The advances and characteristics of high-power diode laser materials processing

    Science.gov (United States)

    Li, Lin

    2000-10-01

    This paper presents a review of the direct applications of high-power diode lasers for materials processing including soldering, surface modification (hardening, cladding, glazing and wetting modifications), welding, scribing, sheet metal bending, marking, engraving, paint stripping, powder sintering, synthesis, brazing and machining. The specific advantages and disadvantages of diode laser materials processing are compared with CO 2, Nd:YAG and excimer lasers. An effort is made to identify the fundamental differences in their beam/material interaction characteristics and materials behaviour. Also an appraisal of the future prospects of the high-power diode lasers for materials processing is given.

  12. Weldability of Advanced High Strength Steels using Ytterbium:Yttrium Aluminium Garnet high power laser for Tailor-Welded Blank applications

    Science.gov (United States)

    Sharma, Rajashekhar Shivaram

    Use of a high power Yb:YAG laser is investigated for joining advanced high strength steel materials for use in tailor-welded blank (TWB) applications. TWB's are materials of different chemistry, coating or thicknesses that are joined before metal forming and other operations such as trimming, assembly and painting are carried out. TWB is becoming an important design tool in the automotive industry for reducing weight, improving fuel economy and passenger safety, while reducing the overall costs for the customer. Three advanced high strength steels, TRIP780, DP980 and USIBOR, which have many unique properties that are conducive to achieving these objectives, along with mild steel, are used in this work. The objective of this work is to ensure that high quality welds can be obtained using Yb:YAG lasers which are also becoming popular for metal joining operations, since they produce high quality laser beams that suffer minimal distortion when transported via fiber optic cables. Various power levels and speeds for the laser beam were used during the investigation. Argon gas was consistently used for shielding purposes during the welding process. After the samples were welded, metallographic examination of the fusion and heat-affected zones using optical and scanning electron microscopes were carried out to determine the microstructures as well as weld defects. Optical and scanning electron microscopes were also used to examine the top of welds as well as fracture surfaces. Additionally, cross-weld microhardness evaluations, tensile tests using Instron tester, limited fatigue tests as well as formability evaluations using OSU plane strain evaluation were carried out. The examinations included a 2-factor full factorial design of experiments to determine the impact of coatings on the surface roughness on the top of the welds. Tensile strengths of DP980, TRIP780 and mild steel materials as well as DP980 welded to TRIP780 and mild steel in the rolling direction as well as

  13. Long distance high power optical laser fiber break detection and continuity monitoring systems and methods

    Energy Technology Data Exchange (ETDEWEB)

    Rinzler, Charles C.; Gray, William C.; Faircloth, Brian O.; Zediker, Mark S.

    2016-02-23

    A monitoring and detection system for use on high power laser systems, long distance high power laser systems and tools for performing high power laser operations. In particular, the monitoring and detection systems provide break detection and continuity protection for performing high power laser operations on, and in, remote and difficult to access locations.

  14. Long distance high power optical laser fiber break detection and continuity monitoring systems and methods

    Energy Technology Data Exchange (ETDEWEB)

    Rinzler, Charles C.; Gray, William C.; Faircloth, Brian O.; Zediker, Mark S.

    2016-02-23

    A monitoring and detection system for use on high power laser systems, long distance high power laser systems and tools for performing high power laser operations. In particular, the monitoring and detection systems provide break detection and continuity protection for performing high power laser operations on, and in, remote and difficult to access locations.

  15. Development of high power quantum well lasers at RRCAT

    CERN Document Server

    Sharma, T K; Dixit, V K; Singh, S D; Pal, S; Porwal, S; Kumar, Ravi; Khakha, Alexander; Jangir, R; Kheraj, V; Rawat, P; Nath, A K

    2014-01-01

    We at RRCAT have recently developed high power laser diodes in the wavelength range of 740 to 1000 nm. A typical semiconductor laser structure is consisted of about 10 epilayers with different composition, thickness and doping values. For example, a laser diode operating at 0.8 micron has either GaAs or GaAsP quantum well as an active layer. The quantum well is sandwiched between AlGaAs wider bandgap waveguide and cladding layers. The complete laser structure is grown by metal organic vapour phase epitaxy technique and devices are fabricated through standard procedure using photolithography. We recently achieved about 5.3 Watt peak power at 853 nm. These laser diodes were tested under pulsed operation at room temperature for 500 nanosecond pulse duration with a duty cycle of 1:1000. Laser diode arrays consisting of 6-10 elements were also developed and tested for operation in pulsed mode at room temperature.

  16. Coherent beam combiner for a high power laser

    Science.gov (United States)

    Dane, C. Brent; Hackel, Lloyd A.

    2002-01-01

    A phase conjugate laser mirror employing Brillouin-enhanced four wave mixing allows multiple independent laser apertures to be phase locked producing an array of diffraction-limited beams with no piston phase errors. The beam combiner has application in laser and optical systems requiring high average power, high pulse energy, and low beam divergence. A broad range of applications exist in laser systems for industrial processing, especially in the field of metal surface treatment and laser shot peening.

  17. Optical fiber transmission of high power excimer laser radiation.

    Science.gov (United States)

    Pini, R; Salimbeni, R; Vannini, M

    1987-10-01

    An experimental investigation of optical fiber transmission of high power excimer laser radiation is presented. Different types of commercially available UV fiber have been tested, measuring energy handling capabilities and transmission losses of short samples at the XeCl (308-nm) and KrF (249-nm) wavelengths by using a standard excimer laser. A power density dependent damage process has been observed over 1 GW/cm(2). Fiber losses due to different radii of curvature are also reported. Experimental results have been examined to evaluate the effectiveness of excimer laser transmission through optical fibers for such medical uses as laser angioplasty, including also a comparison between the use of KrF or XeCl emission lines for this purpose. Finally, optimum excimer laser characteristics to increase the energy coupling in fibers are discussed.

  18. Development of adaptive resonator techniques for high-power lasers

    Energy Technology Data Exchange (ETDEWEB)

    An, J; Brase, J; Carrano, C; Dane, C B; Flath, L; Fochs, S; Hurd, R; Kartz, M; Sawvel, R

    1999-07-12

    The design of an adaptive wavefront control system for a high-power Nd:Glass laser will be presented. Features of this system include: an unstable resonator in confocal configuration, a multi-module slab amplifier, and real-time intracavity adaptive phase control using deformable mirrors and high-speed wavefront sensors. Experimental results demonstrate the adaptive correction of an aberrated passive resonator (no gain).

  19. Transmission grating stretcher for contrast enhancement of high power lasers.

    Science.gov (United States)

    Tang, Yunxin; Hooker, Chris; Chekhlov, Oleg; Hawkes, Steve; Collier, John; Rajeev, P P

    2014-12-01

    We propose, for the first time, a transmission grating stretcher for high power lasers and demonstrate its superiority over conventional, reflective gold grating stretchers in terms of pulse temporal quality. We show that, compared to a conventional stretcher with the same stretching factor, the transmission-grating based stretcher yields more than an order of magnitude improvement in the contrast pedestal. We have also quantitatively characterized the roughness of the grating surfaces and estimated its impact on the contrast pedestal.

  20. Measuring vacuum polarization with high-power lasers

    Institute of Scientific and Technical Information of China (English)

    B.King; T.Heinzl

    2016-01-01

    When exposed to intense electromagnetic fields, the quantum vacuum is expected to exhibit properties of a polarizable medium akin to a weakly nonlinear dielectric material. Various schemes have been proposed to measure such vacuum polarization effects using a combination of high- power lasers. Motivated by several planned experiments, we provide an overview of experimental signatures that have been suggested to confirm this prediction of quantum electrodynamics of real photon–photon scattering.

  1. Tunable Single-Longitudinal-Mode High-Power Fiber Laser

    Directory of Open Access Journals (Sweden)

    Jonas K. Valiunas

    2012-01-01

    Full Text Available We report a novel CW tunable high-power single-longitudinal-mode fiber laser with a linewidth of ∼9 MHz. A tunable fiber Bragg grating provided wavelength selection over a 10 nm range. An all-fiber Fabry-Perot filter was used to increase the longitudinal mode spacing of the laser cavity. An unpumped polarization-maintaining erbium-doped fiber was used inside the cavity to eliminate mode hopping and increase stability. A maximum output power of 300 mW was produced while maintaining single-longitudinal-mode operation.

  2. Electronically controlled heat sink for high-power laser diodes

    Science.gov (United States)

    Vetrovec, John

    2009-05-01

    We report on a novel electronically controlled active heat sink for high-power laser diodes offering unparalleled capacity in high-heat flux handling and temperature control. The heat sink receives diode waste heat at high flux and transfers it at reduced flux to environment, coolant fluid, heat pipe, or structure. Thermal conductance of the heat sink is electronically adjustable, allowing for precise control of diode temperature and the diode light wavelength. When pumping solid-state or alkaline vapor lasers, diode wavelength can be precisely temperature-tuned to the gain medium absorption features. This paper presents the heat sink physics, engineering design, and performance modeling.

  3. Atmospheric propagation of high power laser radiation at different weather conditions

    OpenAIRE

    Pargmann, Carsten; Hall, Thomas; Duschek, Frank; Handke, Jürgen

    2016-01-01

    Applications based on the propagation of high power laser radiation through the atmosphere are limited in range and effect, due to weather dependent beam wandering, beam deterioration, and scattering processes. Security and defense related application examples are countermeasures against hostile projectiles and the powering of satellites and aircrafts. For an examination of the correlations between weather condition and laser beam characteristics DLR operates at Lampoldshausen a 130 m long fr...

  4. High power visible diode laser for the treatment of eye diseases by laser coagulation

    Science.gov (United States)

    Heinrich, Arne; Hagen, Clemens; Harlander, Maximilian; Nussbaumer, Bernhard

    2015-03-01

    We present a high power visible diode laser enabling a low-cost treatment of eye diseases by laser coagulation, including the two leading causes of blindness worldwide (diabetic retinopathy, age-related macular degeneration) as well as retinopathy of prematurely born children, intraocular tumors and retinal detachment. Laser coagulation requires the exposure of the eye to visible laser light and relies on the high absorption of the retina. The need for treatment is constantly increasing, due to the demographic trend, the increasing average life expectancy and medical care demand in developing countries. The World Health Organization reacts to this demand with global programs like the VISION 2020 "The right to sight" and the following Universal Eye Health within their Global Action Plan (2014-2019). One major point is to motivate companies and research institutes to make eye treatment cheaper and easily accessible. Therefore it becomes capital providing the ophthalmology market with cost competitive, simple and reliable technologies. Our laser is based on the direct second harmonic generation of the light emitted from a tapered laser diode and has already shown reliable optical performance. All components are produced in wafer scale processes and the resulting strong economy of scale results in a price competitive laser. In a broader perspective the technology behind our laser has a huge potential in non-medical applications like welding, cutting, marking and finally laser-illuminated projection.

  5. Coherent beam combining architectures for high power tapered laser arrays

    Science.gov (United States)

    Schimmel, G.; Janicot, S.; Hanna, M.; Decker, J.; Crump, P.; Erbert, G.; Witte, U.; Traub, M.; Georges, P.; Lucas-Leclin, G.

    2017-02-01

    Coherent beam combining (CBC) aims at increasing the spatial brightness of lasers. It consists in maintaining a constant phase relationship between different emitters, in order to combine them constructively in one single beam. We have investigated the CBC of an array of five individually-addressable high-power tapered laser diodes at λ = 976 nm, in two architectures: the first one utilizes the self-organization of the lasers in an interferometric extended-cavity, which ensures their mutual coherence; the second one relies on the injection of the emitters by a single-frequency laser diode. In both cases, the coherent combining of the phase-locked beams is ensured on the front side of the array by a transmission diffractive grating with 98% efficiency. The passive phase-locking of the laser bar is obtained up to 5 A (per emitter). An optimization algorithm is implemented to find the proper currents in the five ridge sections that ensured the maximum combined power on the front side. Under these conditions we achieve a maximum combined power of 7.5 W. In the active MOPA configuration, we can increase the currents in the tapered sections up to 6 A and get a combined power of 11.5 W, corresponding to a combining efficiency of 76%. It is limited by the beam quality of the tapered emitters and by fast phase fluctuations between emitters. Still, these results confirm the potential of CBC approaches with tapered lasers to provide a high-power and high-brightness beam, and compare with the current state-of-the-art with laser diodes.

  6. Challenges of high power diode-pumped lasers for fusion energy

    Institute of Scientific and Technical Information of China (English)

    Bruno; Le; Garrec

    2014-01-01

    This paper reviews the different challenges that are encountered in the delivery of high power lasers as drivers for fusion energy.We will focus on diode-pumped solid-state lasers and we will highlight some of the main recent achievements when using ytterbium,cryogenic cooling and ceramic gain media.Apart from some existing fusion facilities and some military applications of diode-pumped solid-state lasers,we will show that diode-pumped solid-state lasers are scalable to inertial fusion energy(IFE)’s facility level and that the all-fiber laser scheme is very promising.

  7. Safety approaches for high power modular laser operation

    Science.gov (United States)

    Handren, R. T.

    1993-03-01

    Approximately 20 years ago, a program was initiated at the Lawrence Livermore National Laboratory (LLNL) to study the feasibility of using lasers to separate isotopes of uranium and other materials. Of particular interest was the development of a uranium enrichment method for the production of commercial nuclear power reactor fuel to replace current more expensive methods. The Uranium Atomic Vapor Laser Isotope Separation (U-AVLIS) Program progressed to the point where a plant-scale facility to demonstrate commercial feasibility was built and is being tested. The U-AVLIS Program uses copper vapor lasers which pump frequency selective dye lasers to photoionize uranium vapor produced by an electron beam. The selectively ionized isotopes are electrostatically collected. The copper lasers are arranged in oscillator/amplifier chains. The current configuration consists of 12 chains, each with a nominal output of 800 W for a system output in excess of 9 kW. The system requirements are for continuous operation (24 h a day, 7 days a week) and high availability. To meet these requirements, the lasers are designed in a modular form allowing for rapid change-out of the lasers requiring maintenance. Since beginning operation in early 1985, the copper lasers have accumulated over 2 million unit hours at a greater than 90% availability. The dye laser system provides approximately 2.5 kW average power in the visible wavelength range. This large-scale laser system has many safety considerations, including high-power laser beams, high voltage, and large quantities (approximately 3000 gal) of ethanol dye solutions. The Laboratory's safety policy requires that safety controls be designed into any process, equipment, or apparatus in the form of engineering controls. Administrative controls further reduce the risk to an acceptable level. Selected examples of engineering and administrative controls currently being used in the U-AVLIS Program are described.

  8. Degradation mechanisms in high-power multi-mode InGaAs-AlGaAs strained quantum well lasers for high-reliability applications

    Science.gov (United States)

    Sin, Yongkun; Presser, Nathan; Brodie, Miles; Lingley, Zachary; Foran, Brendan; Moss, Steven C.

    2015-03-01

    Laser diode manufacturers perform accelerated multi-cell lifetests to estimate lifetimes of lasers using an empirical model. Since state-of-the-art laser diodes typically require a long period of latency before they degrade, significant amount of stress is applied to the lasers to generate failures in relatively short test durations. A drawback of this approach is the lack of mean-time-to-failure data under intermediate and low stress conditions, leading to uncertainty in model parameters (especially optical power and current exponent) and potential overestimation of lifetimes at usage conditions. This approach is a concern especially for satellite communication systems where high reliability is required of lasers for long-term duration in the space environment. A number of groups have studied reliability and degradation processes in GaAs-based lasers, but none of these studies have yielded a reliability model based on the physics of failure. The lack of such a model is also a concern for space applications where complete understanding of degradation mechanisms is necessary. Our present study addresses the aforementioned issues by performing long-term lifetests under low stress conditions followed by failure mode analysis (FMA) and physics of failure investigation. We performed low-stress lifetests on both MBE- and MOCVD-grown broad-area InGaAs- AlGaAs strained QW lasers under ACC (automatic current control) mode to study low-stress degradation mechanisms. Our lifetests have accumulated over 36,000 test hours and FMA is performed on failures using our angle polishing technique followed by EL. This technique allows us to identify failure types by observing dark line defects through a window introduced in backside metal contacts. We also investigated degradation mechanisms in MOCVD-grown broad-area InGaAs-AlGaAs strained QW lasers using various FMA techniques. Since it is a challenge to control defect densities during the growth of laser structures, we chose to

  9. High-power one-, two-, and three-dimensional photonic crystal edge-emitting laser diodes for ultra-high brightness applications

    Science.gov (United States)

    Gordeev, N. Yu.; Maximov, M. V.; Shernyakov, Y. M.; Novikov, I. I.; Karachinsky, L. Ya.; Shchukin, V. A.; Kettler, T.; Posilovic, K.; Ledentsov, N. N.; Bimberg, D.; Duboc, R.; Sharon, A.; Arbiv, D. B.; Ben-Ami, U.

    2008-02-01

    Direct laser diodes can typically provide only a limited single mode power, while ultrahigh-brightness is required for many of the market-relevant applications. Thus, multistage power conversion schemes are applied, when the laser diodes are used just as a pumping source. In this paper we review the recent advances in ultra-large output aperture edge-emitting lasers based on the photonic band crystal (PBC) concept. The concept allows near- and far-field engineering robust to temperature and strain gradients and growth nonuniformities. High-order modes are selectively filtered and the effective optical confinement of the fundamental mode can be dramatically enhanced. At first, we show that robust ultra-narrow vertical beam divergence (operation by processing of the multistripe arrays along their lengths. The concept opens a way for 3D photonic crystal edge emitting lasers potentially allowing scalable single mode power increase to arbitrary high levels.

  10. Quality and performance of laser cutting with a high power SM fiber laser

    DEFF Research Database (Denmark)

    Kristiansen, Morten; Selchau, Jacob; Olsen, F. O.

    2013-01-01

    The introduction of high power single mode fiber lasers allows for a beam of high power and a good beam quality factor (M2 ” 1.2), compared to the multimode fiber lasers often utilised in macro laser metal cutting. This paper describes fundamental studies of macro laser metal cutting with a single...... mode fiber laser to study the performance of such lasers in terms of cut quality and process performance. Linear cut experiments have been performed applying a 3kW single mode fiber laser and varying the following parameters: laser power, cutting speed, focal length, focus position, cutting gas...... influence the cut quality and the maximum cutting speed in the investigated parameter space. Furthermore the achieved cutting performance is benchmarked to laser cutting with other types of lasers, CO2-lasers, disc-lasers as well as multimode fiber lasers....

  11. Optical monitoring of high power direct diode laser cladding

    Science.gov (United States)

    Liu, Shuang; Farahmand, Parisa; Kovacevic, Radovan

    2014-12-01

    Laser cladding is one of the most advanced surface modification techniques which can be used to build and repair high-value components. High power direct diode laser (HPDDL) offers unique quality and cost advantages over other lasers (CO2, Nd:YAG). Especially its rectangular laser beam with top-hat intensity distribution makes HPDDL an ideal tool for large area cladding. In order to utilize this technique successfully, the development of on-line monitoring and process control is necessary. In this study, an optical monitoring system consisting of a high-speed CCD camera, a pyrometer, and an infrared camera was used to analyze the mass- and heat-transfer in the cladding process. The particle transport in flight was viewed by a high-speed CCD camera; the interaction between powder flow and laser beam was observed by an infrared camera; and the thermal behavior of the molten pool was recorded by the pyrometer and the infrared camera. The effects of the processing parameters on the laser attenuation, particle heating and clad properties were investigated based on the obtained signals. The optical monitoring method improved the understanding about mutual interrelated phenomena in the cladding process.

  12. Optical Systems For High Power Laser Beam Delivery

    Science.gov (United States)

    Durville, Frederic M.; Cilia, D.

    1989-03-01

    During the pst fifteen years, pwerful lasers have been developed for industrial applications such as cutting, piercing, welding, engraving, etc... Convenient and reliable delivery systems are still needed to widen their field of application.

  13. High brilliance and high efficiency: optimized high power diode laser bars

    Science.gov (United States)

    Hülsewede, R.; Schulze, H.; Sebastian, J.; Schröder, D.; Meusel, J.; Hennig, P.

    2008-02-01

    The strong increasing laser market has ongoing demands to reduce the costs of diode laser pumped systems. For that reason JENOPTIK Diode Lab GmbH (JDL) optimized the bar brilliance (small vertical far field divergence) and bar efficiency (higher optical power operation) with respect to the pump applications. High efficiency reduces the costs for mounting and cooling and high brilliance increases the coupling efficiency. Both are carefully adjusted in the 9xx nm - high power diode laser bars for pump applications in disc- and fiber lasers. Based on low loss waveguide structures high brilliance bars with 19° fast axis beam divergence (FWHM) with 58 % maximum efficiency and 27° fast axis beam divergence (FWHM) with 62 % maximum efficiency are developed. Mounted on conductive cooled heat sinks high power operation with lifetime > 20.000 hours at 120 W output power level (50 % filling factor bars) and 80W (20 % filling factor bars) is demonstrated. 808nm bars used as pump sources for Nd:YAG solid state lasers are still dominating in the market. With respect to the demands on high reliability at high power operation current results of a 100 W high power life time test are showing more than 9000 hour operation time for passively cooled packaged high efficiency 50 % filling factor bars. Measurement of the COMD-level after this hard pulse life time test demonstrates very high power levels with no significant droop in COMD-power level. This confirms the high facet stability of JDL's facet technology. New high power diode laser bars with wavelength of 825 nm and 885 nm are still under development and first results are presented.

  14. Non-solid non-rigid optics for high-power laser systems

    CSIR Research Space (South Africa)

    Michaelis, MM

    2006-06-14

    Full Text Available Fusion (LF). LF is the one high power application where NSNRO has been routinely employed, namely in the aforementioned Nova plasma isolator. NIF and “Laser Megajoule” may fire at most a few shots per day (not many less than Nova, Omega and GEKKO...

  15. Advances in CO2 laser fabrication for high power fibre laser devices

    Science.gov (United States)

    Boyd, Keiron; Rees, Simon; Simakov, Nikita; Daniel, Jae M. O.; Swain, Robert; Mies, Eric; Hemming, Alexander; Clarkson, W. A.; Haub, John

    2016-03-01

    CO2 laser processing facilitates contamination free, rapid, precise and reproducible fabrication of devices for high power fibre laser applications. We present recent progress in fibre end-face preparation and cladding surface modification techniques. We demonstrate a fine feature CO2 laser process that yields topography significantly smaller than that achieved with typical mechanical cleaving processes. We also investigate the side processing of optical fibres for the fabrication of all-glass cladding light strippers and demonstrate extremely efficient cladding mode removal. We apply both techniques to fibres with complex designs containing multiple layers of doped and un-doped silica as well as shaped and circularly symmetric structures. Finally, we discuss the challenges and approaches to working with various fibre and glass-types.

  16. Recent brightness improvements of 976 nm high power laser bars

    Science.gov (United States)

    Bachmann, Alexander; Lauer, Christian; Furitsch, Michael; König, Harald; Müller, Martin; Strauß, Uwe

    2017-02-01

    Pump modules for fiber lasers and fiber-coupled direct diode laser systems require laser diodes with a high beam quality. While in fast axis direction diode lasers exhibit a nearly diffraction limited output beam, the maximum usable output power is usually limited by the slow axis divergence blooming at high power levels. Measures to improve the lateral beam quality are subject of extensive research. Among the many influencing factors are the chip temperature, thermal crosstalk between emitters, thermal lensing, lateral waveguiding and lateral mode structure. We present results on the improvements of the lateral beam divergence and brightness of gain-guided mini-bars for emission at 976 nm. For efficient fiber coupling into a 200 μm fiber with NA 0.22, the upper limit of the lateral beam parameter product is 15.5 mm mrad. Within the last years, the power level at this beam quality has been improved from 44 W to 52 W for the chips in production, enabling more cost efficient pump modules and laser systems. Our work towards further improvements of the beam quality focuses on advanced chip designs featuring reduced thermal lensing and mode shaping. Recent R&D results will be presented, showing a further improvement of the beam quality by 15%. Also, results of a chip design with an improved lateral emitter design for highest brightness levels will be shown, yielding in a record high brightness saturation of 4.8 W/mm mrad.

  17. Optimization of TM-Doped Phosphosilicate Glass for High Power Fiber Lasers

    Science.gov (United States)

    2016-04-28

    High power fiber lasers have been revolutionizing machining in manufacturing in the past decade. Increasingly, automotive industries are turning to the...micro- machining at precision much beyond current mechanical tools with a focused laser beam and high throughput machining of much harder materials...such as glass and ceramics, again way beyond the capability of current mechanical tools. Some of the key applications include drilling micron-size

  18. High-power laser experiments to study collisionless shock generation

    Science.gov (United States)

    Sakawa, Y.; Kuramitsu, Y.; Morita, T.; Kato, T.; Tanji, H.; Ide, T.; Nishio, K.; Kuwada, M.; Tsubouchi, T.; Ide, H.; Norimatsu, T.; Gregory, C.; Woolsey, N.; Schaar, K.; Murphy, C.; Gregori, G.; Diziere, A.; Pelka, A.; Koenig, M.; Wang, S.; Dong, Q.; Li, Y.; Park, H.-S.; Ross, S.; Kugland, N.; Ryutov, D.; Remington, B.; Spitkovsky, A.; Froula, D.; Takabe, H.

    2013-11-01

    A collisionless Weibel-instability mediated shock in a self-generated magnetic field is studied using two-dimensional particle-in-cell simulation [Kato and Takabe, Astophys. J. Lett. 681, L93 (2008)]. It is predicted that the generation of the Weibel shock requires to use NIF-class high-power laser system. Collisionless electrostatic shocks are produced in counter-streaming plasmas using Gekko XII laser system [Kuramitsu et al., Phys. Rev. Lett. 106, 175002 (2011)]. A NIF facility time proposal is approved to study the formation of the collisionless Weibel shock. OMEGA and OMEGA EP experiments have been started to study the plasma conditions of counter-streaming plasmas required for the NIF experiment using Thomson scattering and to develop proton radiography diagnostics.

  19. Cladded single crystal fibers for high power fiber lasers

    Science.gov (United States)

    Kim, W.; Shaw, B.; Bayya, S.; Askins, C.; Peele, J.; Rhonehouse, D.; Meyers, J.; Thapa, R.; Gibson, D.; Sanghera, J.

    2016-09-01

    We report on the recent progress in the development of cladded single crystal fibers for high power single frequency lasers. Various rare earth doped single crystal YAG fibers with diameters down to 17 μm with length > 1 m have been successfully drawn using a state-of-the-art Laser Heated Pedestal Growth system. Single and double cladding on rare earth doped YAG fibers have been developed using glasses where optical and physical properties were precisely matched to doped YAG core single crystal fiber. The double clad Yb:YAG fiber structures have dimensions analogous to large mode area (LMA) silica fiber. We also report successful fabrications of all crystalline core/clad fibers where thermal and optical properties are superior over glass cladded YAG fibers. Various fabrication methods, optical characterization and gain measurements on these cladded YAG fibers are reported.

  20. High-power laser experiments to study collisionless shock generation

    Directory of Open Access Journals (Sweden)

    Sakawa Y.

    2013-11-01

    Full Text Available A collisionless Weibel-instability mediated shock in a self-generated magnetic field is studied using two-dimensional particle-in-cell simulation [Kato and Takabe, Astophys. J. Lett. 681, L93 (2008]. It is predicted that the generation of the Weibel shock requires to use NIF-class high-power laser system. Collisionless electrostatic shocks are produced in counter-streaming plasmas using Gekko XII laser system [Kuramitsu et al., Phys. Rev. Lett. 106, 175002 (2011]. A NIF facility time proposal is approved to study the formation of the collisionless Weibel shock. OMEGA and OMEGA EP experiments have been started to study the plasma conditions of counter-streaming plasmas required for the NIF experiment using Thomson scattering and to develop proton radiography diagnostics.

  1. 157 W all-fiber high-power picosecond laser.

    Science.gov (United States)

    Song, Rui; Hou, Jing; Chen, Shengping; Yang, Weiqiang; Lu, Qisheng

    2012-05-01

    An all-fiber high-power picosecond laser is constructed in a master oscillator power amplifier configuration. The self-constructed fiber laser seed is passively mode locked by a semiconductor saturable absorber mirror. Average output power of 157 W is obtained after three stages of amplification at a fundamental repetition rate of 60 MHz. A short length of ytterbium double-clad fiber with a high doping level is used to suppress nonlinear effects. However, a stimulated Raman scattering (SRS) effect occurs owing to the 78 kW high peak power. A self-made all-fiber repetition rate increasing system is used to octuple the repetition rate and decrease the high peak power. Average output power of 156.6 W is obtained without SRS under the same pump power at a 480 MHz repetition rate with 0.6 nm line width.

  2. Thermal Effect in KTP Crystals During High Power Laser Operation

    Institute of Scientific and Technical Information of China (English)

    YAO Jian-Quan; YU Yi-Zhong; CHEN Jin; ZHANG Fan; WANG Peng; WANG Tao; ZHANG Bai-Gang

    2001-01-01

    We report on the theoretical and experimental studies of the thermal effect of the KTP crystal during high power operation. From the dependence of the refractive index temperature coefficients on wavelength, the dependence of the optimum phase-matching angles on temperature is derived. In the experiment, the angle of the frequency-doubled KTP crystal is tilted to compensate for the thermal effect and to obtain △φ = 0.7° when the green laser output power is 30 W and the KTP crystal temperature is about 80°C. We obtained the highest stable output power greater than 40 W with an L-shaped flat-flat intracavity frequency-doubled Nd:YAG laser. The experimental results are very consistent with the theoretical analysis.

  3. Control system for high power laser drilling workover and completion unit

    Energy Technology Data Exchange (ETDEWEB)

    Zediker, Mark S; Makki, Siamak; Faircloth, Brian O; DeWitt, Ronald A; Allen, Erik C; Underwood, Lance D

    2015-05-12

    A control and monitoring system controls and monitors a high power laser system for performing high power laser operations. The control and monitoring system is configured to perform high power laser operation on, and in, remote and difficult to access locations.

  4. 122-W high-power single-frequency MOPA fiber laser in all-fiber format

    Institute of Scientific and Technical Information of China (English)

    Xiaolin Dong; Hu Xiao; Shanhui Xu; Zhiyong Pan; Yanxing Ma; Xiaolin Wang; Pu Zhou; Zhongmin Yang

    2011-01-01

    High-power single-frequency lasers have been found widespread applications in science and industries,such as gravitational wave detection,coherent and spectrum beam combining,range finding,and lidar[1- 7].In such cases,the localization of high-power single-frequency fiber laser is extremely important for domestic researchers.The power of single-frequency fiber lasers has increased dramatically in recent years.Most previously presented high-power single-frequency fiber lasers are based on bulk optics configuration,which have big sizes and massive weights.The use of aIl-fiber-based components can significantly simplify the system configuration and make the system more compact and robust[8-10].In this letter,we report a high-power single-frequency master oscillator power amplifier (MOPA) fiber laser in all-fiber format.The MOPA fiber laser consists of twostage amplification architecture.The maximum output power is 122 W,with slope efficiency of 72%.%We demonstrate a high-power single-frequency master oscillator power amplifier (MOPA) fiber laser. The central wavelength of the single-frequency fiber lager seed is 1 063.8 nm, with a linewidth narrower than 20 kHz and output power of 120 mW. By using two-stage amplification, a single-frequency fiber laser with an output power of 122 W is obtained, and the optical-optical conversion efficiency is 72%. No significant amplified spontaneous emission (ASE) or stimulated Brillouin scattering (SBS) is observed. The output power can be further increased by launching more pump power.

  5. Active Photonic crystal fibers for high power applications

    DEFF Research Database (Denmark)

    Olausson, Christina Bjarnal Thulin

    . This plays an important role in high power lasers and ampliers with respect to efficiency, packaging, and thermal handling. The third part of the work has involved developing tools for characterizing the mode quality and stability of large core bers. Stable, single-mode bers with larger cores are essential......The photonic crystal ber technology provides means to realize bers optimized for high power operation, due to the large single-mode cores and the unique design exibility of the microstructure. The work presented in this thesis focuses on improving the properties of active photonic crystal bers...... for high power ber lasers and ampliers, and on adding new functionality to the fibers - all with the purpose of pushing the technology towards high powers. The first part of the work has been to investigate photo darkening, the mitigation of which is crucial in the quest for higher powers. The work has...

  6. Thermal tuning of volume Bragg gratings for spectral beam combining of high-power fiber lasers.

    Science.gov (United States)

    Drachenberg, Derrek R; Andrusyak, Oleksiy; Venus, George; Smirnov, Vadim; Glebov, Leonid B

    2014-02-20

    High-radiance lasers are desired for many applications in defense and manufacturing. Spectral beam combining (SBC) by volume Bragg gratings (VBGs) is a very promising method for high-radiance lasers that need to achieve 100 kW level power. Laser-induced heating of VBGs under high-power radiation presents a challenge for maintaining Bragg resonance at various power levels without mechanical realignment. A novel thermal tuning technique and apparatus is presented that enables maintaining peak efficiency operation of the SBC system at various power levels without any mechanical adjustment. The method is demonstrated by combining two high-power ytterbium fiber lasers with high efficiency from low power to full combined power of 300 W (1.5 kW effective power), while maintaining peak combining efficiency within 0.5%.

  7. High-power Yb-doped continuous-wave and pulsed fibre lasers

    Indian Academy of Sciences (India)

    B N Upadhyaya

    2014-01-01

    High-power laser generation using Yb-doped double-clad fibres with conversion efficiencies in excess of 80% have attracted much attention during the last decade due to their inherent advantages in terms of very high efficiency, no misalignment due to in-built intracore fibre Bragg gratings, low thermal problems due to large surface to volume ratio, diffraction-limited beam quality, compactness, reliability and fibre-optic beam delivery. Yb-doped fibres can also provide a wide emission band from ∼1010 nm to ∼1170 nm, which makes it a versatile laser medium to realize continuous-wave (CW), Q-switched short pulse, and mode-locked ultrashort pulse generation for various applications. In this article, a review of Yb-doped CW and pulsed fibre lasers along with our study on self-pulsing dynamics in CW fibre lasers to find its role in high-power fibre laser development and the physical mechanisms involved in its generation has been described. A study on the generation of high-power CWfibre laser of 165Woutput power and generation of high peak power nanosecond pulses from acousto-optic Q-switched fibre laser has also been presented.

  8. Atmospheric propagation of high power laser radiation at different weather conditions

    Science.gov (United States)

    Pargmann, Carsten; Hall, Thomas; Duschek, Frank; Handke, Jürgen

    2016-05-01

    Applications based on the propagation of high power laser radiation through the atmosphere are limited in range and effect, due to weather dependent beam wandering, beam deterioration, and scattering processes. Security and defense related application examples are countermeasures against hostile projectiles and the powering of satellites and aircrafts. For an examination of the correlations between weather condition and laser beam characteristics DLR operates at Lampoldshausen a 130 m long free transmission laser test range. Sensors around this test range continuously monitor turbulence strength, visibility, precipitation, temperature, and wind speed. High power laser radiation is obtained by a TruDisk 6001 disk laser (Trumpf company) yielding a maximum output power of 6 kW at a wavelength of 1030 nm. The laser beam is expanded to 180 mm and focused along the beam path. Power and intensity distribution are measured before and after propagation, providing information about the atmospheric transmission and alterations of diameter and position of the laser beam. Backscattered laser light is acquired by a photo receiver. As a result, measurements performed at different weather conditions show a couple of correlations to the characteristics of the laser beam. The experimental results are compared to a numerical analysis. The calculations are based on the Maxwell wave equation in Fresnel approximation. The turbulence is considered by the introduction of phase screens and the "von Karman" spectrum.

  9. Compact, Low-Cost, Frequency-Locked Semiconductor Laser for Injection Seeding High Power Laser Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This NASA Small Business Innovative Research Phase II project will develop a compact, low-cost, wavelength locked seed laser for injection locking high powered...

  10. Laser ablation of borosilicate glass with high power shaped UV nanosecond laser pulses

    Science.gov (United States)

    von Witzendorff, Philipp; Bordin, Andrea; Suttmann, Oliver; Patel, Rajesh S.; Bovatsek, James; Overmeyer, Ludger

    2016-03-01

    The application of thin borosilicate glass as interposer material requires methods for separation and drilling of this material. Laser processing with short and ultra-short laser pulses have proven to enable high quality cuts by either direct ablation or internal glass modification and cleavage. A recently developed high power UV nanosecond laser source allows for pulse shaping of individual laser pulses. Thus, the pulse duration, pulse bursts and the repetition rate can be set individually at a maximum output power of up to 60 W. This opens a completely new process window, which could not be entered with conventional Q-switched pulsed laser sources. In this study, the novel pulsed UV laser system was used to study the laser ablation process on 400 μm thin borosilicate glass at different pulse durations ranging from 2 - 10 ns and a pulse burst with two 10 ns laser pulses with a separation of 10 ns. Single line scan experiments were performed to correlate the process parameters and the laser pulse shape with the ablation depth and cutting edge chipping. Increasing the pulse duration within the single pulse experiments from 2 ns to longer pulse durations led to a moderate increase in ablation depth and a significant increase in chipping. The highest material removal was achieved with the 2x10 ns pulse burst. Experimental data also suggest that chipping could be reduced, while maintaining a high ablation depth by selecting an adequate pulse overlap. We also demonstrate that real-time combination of different pulse patterns during drilling a thin borosilicate glass produced holes with low overall chipping at a high throughput rate.

  11. Liquid metal heat sink for high-power laser diodes

    Science.gov (United States)

    Vetrovec, John; Litt, Amardeep S.; Copeland, Drew A.; Junghans, Jeremy; Durkee, Roger

    2013-02-01

    We report on the development of a novel, ultra-low thermal resistance active heat sink (AHS) for thermal management of high-power laser diodes (HPLD) and other electronic and photonic components. AHS uses a liquid metal coolant flowing at high speed in a miniature closed and sealed loop. The liquid metal coolant receives waste heat from an HPLD at high flux and transfers it at much reduced flux to environment, primary coolant fluid, heat pipe, or structure. Liquid metal flow is maintained electromagnetically without any moving parts. Velocity of liquid metal flow can be controlled electronically, thus allowing for temperature control of HPLD wavelength. This feature also enables operation at a stable wavelength over a broad range of ambient conditions. Results from testing an HPLD cooled by AHS are presented.

  12. Prototype of a high-power, high-energy industrial XeCl laser

    Science.gov (United States)

    Borisov, V. M.; Demin, A. I.; Khristoforov, O. B.

    2015-03-01

    We discuss the results of fabrication and experimental study of a high-power excimer XeCl laser for industrial applications. Compactness of the laser is achieved by the employment of a laser chamber based on a ceramic tube made of Al2O3. High laser output energy (1.5 - 2.5 J pulse-1) is obtained using a wide-aperture (up to 55 × 30 mm) volume discharge with pre-ionisation by a creeping discharge. The pre-ionisation is realised through a semitransparent electrode by the UV radiation of a creeping discharge in the form of uniform plasma sheet on a surface of a plane sapphire plate. The operating lifetime of the gas mixture amounts to ~57 × 106 pulses at a stabilised average laser power of 450 W. The results obtained demonstrate real prospects for developing a new class of excimer XeCl lasers with an average power of ~1 kW.

  13. Wavefront control of high power laser beams for the National Ignition Facility (NIF)

    Energy Technology Data Exchange (ETDEWEB)

    Bliss, E; Feldman, M; Grey, A; Koch, J; Lund, L; Sacks, R; Smith, D; Stolz, C; Van Atta, L; Winters, S; Woods, B; Zacharias, R

    1999-09-22

    The use of lasers as the driver for inertial confinement fusion and weapons physics experiments is based on their ability to produce high-energy short pulses in a beam with low divergence. Indeed, the focus ability of high quality laser beams far exceeds alternate technologies and is a major factor in the rationale for building high power lasers for such applications. The National Ignition Facility (NIF) is a large, 192-beam, high-power laser facility under construction at the Lawrence Livermore National Laboratory for fusion and weapons physics experiments. Its uncorrected minimum focal spot size is limited by laser system aberrations. The NIF includes a Wavefront Control System to correct these aberrations to yield a focal spot small enough for its applications. Sources of aberrations to be corrected include prompt pump-induced distortions in the laser amplifiers, previous-shot thermal distortions, beam off-axis effects, and gravity, mounting, and coating-induced optic distortions. Aberrations from gas density variations and optic manufacturing figure errors are also partially corrected. This paper provides an overview of the NIF Wavefront Control System and describes the target spot size performance improvement it affords. It describes provisions made to accommodate the NIF's high fluence (laser beam and flashlamp), large wavefront correction range, wavefront temporal bandwidth, temperature and humidity variations, cleanliness requirements, and exception handling requirements (e.g. wavefront out-of-limits conditions).

  14. CVD grown diamond: A new material for high power CO{sub 2}-lasers

    Energy Technology Data Exchange (ETDEWEB)

    Massart, M.; Union, P.; Muys, P. [Radius Engineering N.V., Gent (Belgium)] [and others

    1996-12-31

    In CO{sub 2} laser engineering, combining high output power with low distortion of the laser beam is an ongoing challenge, leading to a search for optics with low absorption and high thermal conductivity. As CVD diamond has recently become available in larger sizes and with better surface quality, this material can now be assessed for use in high power CO{sub 2} laser optics. This paper presents the systematic study of diamond as a substrate material for optics at 10.6 microns. CO{sub 2}-laser calorimetry has been used for the measurement of absorption of laser power in uncoated and antireflection coated diamond optics. The bulk absorption coefficient of natural and CVD diamond is more than a magnitude higher than that of ZnSe, however, a laser window needs to be antireflection coated, and this (together with the ability to use thinner windows of diamond because of its greater strength) reduces the increase in overall absorption for the window to about a factor of three (or {approximately} 0.7%). In high power applications this is more than compensated for by the substantially higher thermal conductivity of diamond. Laser induced damage threshold (LIDT) measurements have been made on antireflection coated diamond optics. These measurements have been performed using a TEA CO{sub 2}-laser with a peak pulse width of 150 ns at 10.6 microns, and the results are reported here.

  15. Injection locking of a high power ultraviolet laser diode for laser cooling of ytterbium atoms.

    Science.gov (United States)

    Hosoya, Toshiyuki; Miranda, Martin; Inoue, Ryotaro; Kozuma, Mikio

    2015-07-01

    We developed a high-power laser system at a wavelength of 399 nm for laser cooling of ytterbium atoms with ultraviolet laser diodes. The system is composed of an external cavity laser diode providing frequency stabilized output at a power of 40 mW and another laser diode for amplifying the laser power up to 220 mW by injection locking. The systematic method for optimization of our injection locking can also be applied to high power light sources at any other wavelengths. Our system does not depend on complex nonlinear frequency-doubling and can be made compact, which will be useful for providing light sources for laser cooling experiments including transportable optical lattice clocks.

  16. Advances in 808nm high power diode laser bars and single emitters

    Science.gov (United States)

    Morales, J.; Lehkonen, S.; Liu, G.; Schleuning, D.; Acklin, B.

    2016-03-01

    Key applications for 780-830nm high power diode lasers include the pumping of various gas, solid state, and fiber laser media; medical and aesthetic applications including hair removal; direct diode materials processing; and computer-to-plate (CtP) printing. Many of these applications require high brightness fiber coupled beam delivery, in turn requiring high brightness optical output at the bar and chip level. Many require multiple bars per system, with aggregate powers on the order of kWs, placing a premium on high power and high power conversion efficiency. This paper presents Coherent's recent advances in the production of high power, high brightness, high efficiency bars and chips at 780-830nm. Results are presented for bars and single emitters of various geometries. Performance data is presented demonstrating peak power conversion efficiencies of 63% in CW mode. Reliability data is presented demonstrating <50k hours lifetime for products including 60W 18% fill factor and 80W 28% fill factor conduction cooled bars, and <1e9 shots lifetime for 500W QCW bars.

  17. Systems and assemblies for transferring high power laser energy through a rotating junction

    Energy Technology Data Exchange (ETDEWEB)

    Norton, Ryan J.; McKay, Ryan P.; Fraze, Jason D.; Rinzler, Charles C.; Grubb, Daryl L.; Faircloth, Brian O.; Zediker, Mark S.

    2016-01-26

    There are provided high power laser devices and systems for transmitting a high power laser beam across a rotating assembly, including optical slip rings and optical rotational coupling assemblies. These devices can transmit the laser beam through the rotation zone in free space or within a fiber.

  18. High power fiber lasers in geothermal, oil and gas

    Science.gov (United States)

    Zediker, Mark S.

    2014-03-01

    The subject of this paper is the requirements, design, fabrication, and testing of a prototype laser rock drilling system capable of penetrating even the hardest rocks found deep in the earth. The Oil and Gas industry still uses many of the technologies that were in use at the turn of the 19th century. The drilling industry started with a great innovation with the introduction of the tri-cone bit by Howard Hughes in 1908. Since then, the industry has modified and optimized drilling systems with incremental advancement in the ability to penetrate hard crystalline rock structures. Most oil producing reservoirs are located in or below relatively soft rock formations, however, with the growing need for energy, oil companies are now attempting to drill through very hard surface rock and deep ocean formations with limited success. This paper will discuss the types of laser suitable for this application, the requirements for putting lasers in the field, the technology needed to support this laser application and the test results of components developed specifically by Foro Energy for the drilling application.

  19. Development of high-brightness high-power fiber laser pump sources

    Science.gov (United States)

    Priest, J. A.; Faircloth, Brian O.; Swint, Reuel B.; Coleman, James J.; Forbes, David V.; Zediker, Mark S.

    2004-06-01

    High power fiber lasers have strong potential for use in both commercial and military applications. Improved wall plug efficiency over Nd:YAG and CO2 lasers combined with up to a 10-fold improvement in beam quality, make fiber lasers extremely attractive for industrial applications such as welding and cutting. In military applications, fiber lasers offer a simplified logistic train, a deep magazine limited only by electric power, and a compact footprint, allowing theater defense and self-protection of combat platforms with speed of light engagement and flexible response. Commercial viability of these systems, however, is limited by the availability of compact, cost effective, and reliable diode laser pump sources in the multi-kilowatt regime. The relatively low brightness of diode laser sources has complicated the task of building high power pumps at a reasonable cost. In response to this need, Nuvonyx, Inc. in conjunction with the University of Illinois at Urbana-Champaign, has been developing a new technology for producing high power, single lateral mode devices which do not suffer form the instabilities mentioned above. The waveguide consists of a narrow section, approximately 2 μm wide, which flares to approximately 12 μm wide at the output facet. The flaring of the waveguide increases the gain volume and reduces the optical power density at the facet allowing for higher output power capability. The index guide is defined using an epitaxial process which allows the confinement of the mode to be reduced as the width of the guide expands. Thus, the mode is confined in a single mode waveguide throughout the cavity maintaining stability of the mode to the emitting facet. In November 2002, Nuvonyx, Inc. was awarded a contract with the Air Force Research Lab, Kirtland AFB, Albuquerque, NM, to transition these devices to production quality for use in high-power fiber laser pumps. Partnered with Alfalight, Inc. and the University of Illinois, we have begun initial

  20. Thermal investigation on high power dfb broad area lasers at 975 nm, with 60% efficiency

    Science.gov (United States)

    Mostallino, R.; Garcia, M.; Deshayes, Y.; Larrue, A.; Robert, Y.; Vinet, E.; Bechou, L.; Lecomte, M.; Parillaud, O.; Krakowski, M.

    2016-03-01

    The demand of high power diode lasers in the range of 910-980nm is regularly growing. This kind of device for many applications, such as fiber laser pumping [1], material processing [1], solid-state laser pumping [1], defense and medical/dental. The key role of this device lies in the efficiency (𝜂𝐸) of converting input electrical power into output optical power. The high value of 𝜂𝐸 allows high power level and reduces the need in heat dissipation. The requirement of wavelength stabilization with temperature is more obvious in the case of multimode 975nm diode lasers used for pumping Yb, Er and Yb/Er co-doped solid-state lasers, due to the narrow absorption line close to this wavelength. Such spectral width property (new measurement based on the pulse electrical method and using the T3STERequipment. This method is well known for electronic devices and LEDs but is weakly developed for the high power diodes laser. This crucial measurement compared to spectral one is critical for understand the thermal management of diode laser device and improve the structure based on design for reliability. To have a perfect relation between structure, and their modification, and temperature, FEM simulations are performed using COMSOL software. In this case, we can understand the impact of structure on the isothermal distribution and then reveal the sensitive zones in the diode laser. To validate the simulation, we compare the simulation results to the experimental one and develop an analytical model to determine the different contributions of the thermal heating. This paper reports on the development laser structure and the process techniques required to write the gratings. Performances are particularly characterized in terms of experimental electro-optical characterization and spectral response. The extraction of thermal resistance (Rth) is particularly difficult, because of the implicit low value (Rth ≈ 2𝐾/𝑊) and the multimodal

  1. Simple highly efficient pumping configuration in high-power thin-disk laser

    Science.gov (United States)

    Seyedzamani, Sasan; Eslami, Esmaeil

    2017-08-01

    A simple high-power thin-disk pumping configuration using a radiation combination of four commercially available laser-diode stacks is introduced. Two setup modifications are presented to compensate the nonsuitable shape of the pumping spot arising from low beam quality in our combination method. The effects of setup modifications on pumping spot shapes are confirmed by ray tracing simulations using Trace-pro™ software. All setups are arranged in the laboratory, and the experimental measurements show pumping spots improvements on the disk due to modifications in agreement with simulation results. Output power measurements show that by adapting the pumping spot size to the disk cooling capacity the modified setups can deliver higher output powers and efficiencies. Furthermore, the modifications reduce the laser threshold and improve output laser beam quality. Hence, the modifications make the simple four laser-diodes beam combination applicable for thin-disk laser pumping.

  2. Method and apparatus for delivering high power laser energy over long distances

    Energy Technology Data Exchange (ETDEWEB)

    Zediker, Mark S; Rinzler, Charles C; Faircloth, Brian O; Koblick, Yeshaya; Moxley, Joel F

    2015-04-07

    Systems, devices and methods for the transmission and delivery of high power laser energy deep into the earth and for the suppression of associated nonlinear phenomena. Systems, devices and methods for the laser drilling of a borehole in the earth. These systems can deliver high power laser energy down a deep borehole, while maintaining the high power to advance such boreholes deep into the earth and at highly efficient advancement rates.

  3. Spatial structure of focused beams in high-power fiber and CO2 lasers and peculiarities of their application in cutting

    Science.gov (United States)

    Vasiltsov, V. V.; Galushkin, M. G.; Dubrov, V. D.; Egorov, E. N.; Panchenko, V. Ya; Soloviev, A. V.

    2016-05-01

    The requirements for quality parameters in radiation of different wavelength (i.e. CO2 lasers and fiber lasers) have been defined so as to perform efficient oxygen-free gas laser cutting of large-thickness samples. The main channels of consumption of radiation power in the cutting process have been considered. It is noted that focused beam divergence not only decreases the cutting speed, but also causes cutting quality deterioration.

  4. The use of a high-power laser on swine mitral valve chordae tendineae.

    Science.gov (United States)

    Pinto, Nathali Cordeiro; Chavantes, M Cristina; Zezell, Denise; Deana, Alessandro; Benetti, Carolina; Marcos, Rodrigo Labat; Lopes, Luciana Almeida; Martins, Rodrigo A B Lopes; Aiello, Vera Demarchi; Jatene, Fabio Biscegli; Pomerantzeff, Pablo M A

    2016-08-01

    Worldwide, rheumatic fever remains a significant cause of mitral valve insufficiency. It is responsible for approximately 90 % of early childhood valvular surgeries in Brazil. Elongated or flail chordae are frequently responsible and require surgical correction. The purpose of this study was to analyze and compare the histological tissues of the mitral valve chordae and the mechanical resistance generated by the chordae, both with and without the application of a high-power laser. Twenty normal porcine mitral valve chordae were measured and divided randomly into the following two groups: control group (not subjected to a high-power laser) and laser group (subjected to photonic irradiation). Laser surgery was performed under controlled conditions, using following parameters: λ = 980-nm wavelength, power = 3 W, and energy = 60 J. A mechanical test machine was used in combination with a subsequent histological study to measure chordae tensile properties. A histological analysis demonstrated a typical collagen bundle arrangement in the control group; however, under a particular reached temperature range (48), the collagen bundles assumed different arrangements in the laser group. Significant reductions in the chordae tendineae lengths and changes in their resistance in the laser group were observed, as these chordae exhibited less rigid fibers. The chordae tendineae of normal porcine valves subjected to a high-power laser exhibited its length reduction and less stiffness compared to the control group. A histological analysis of the laser treatment specimens demonstrated differences in collagen bundle spatial organization, following slight changes into tissue temperature.

  5. Propagation of high-power partially coherent fibre laser beams in a real environment

    Institute of Scientific and Technical Information of China (English)

    Tao Ru-Mao; Si Lei; Ma Yan-Xing; Zou Yong-Chao; Zhou Pu

    2011-01-01

    The propagation performance of high-power partially coherent fibre laser beams in a real environment is investigated and the theoretical model of a high-power fibre laser propagating in a real environment is established. The influence of a collimating system and thermal blooming is considered together with atmospheric turbulence and mechanical jitter. The laser energy concentration of partially coherent beams in the far field is calculated and analysed based on the theoretical model. It is shown that the propagation performance of partially coherent beams depends on the collimating system,atmospheric turbulence,mechanical jitter and thermal blooming. The propagation performance of partially coherent beams and fully coherent beams is studied and the results show that partially coherent beams are less sensitive to the influence of thermal blooming,which results in that the energy degeneration for partially coherent beams is only 50%a of that for fully coherent beams. Both partially coherent beams and fully coherent beams become less sensitive to thermal blooming when the average structural constant of the refraction index fluctuations increases to 1.7x10-14 m-2/3. The investigation presents a reference for applications of a high-power fibre laser system.

  6. Design of an Optical System for High Power CO2 Laser Cutting

    DEFF Research Database (Denmark)

    de Lange, D.F.; Meijer, J.; Nielsen, Jakob Skov

    2003-01-01

    The results of a design study for the optical system for cutting with high power CO2 lasers (6 kW and up) will be presented. As transparent materials cannot be used for these power levels, mirrors have been applied. A coaxial cutting gas supply has been designed with a laser beam entrance into th...... independent of the entering beam angle or position. manufacturing tolerances have been compensated in a one time adjustment during the assembly of the optical system. Preliminary cutting results in 13 mm thick steel in a shipyard application show a signinficant improvement in the cutting performance....

  7. High-power lead-acid batteries for different applications

    Science.gov (United States)

    Wagner, Rainer

    High-power lead-acid batteries have been used for a rather long time in various applications, especially for uninterruptible power supplies (UPSs) and starting of automobiles. Future automotive service requires, in addition to cold-cranking performance, the combination of high-power capability, a very good charge-acceptance, and an excellent cycle-life. Such applications include stop-start, regenerative braking, and soft, mild and full hybrid vehicles. For UPS, there has been a clear tendency to shorter discharge times and higher discharge rates. During the past decades, the specific power of lead-acid batteries has been raised steadily and there is still, room for further improvement. This paper gives an overview of the progress made in the development of high-power lead-acid batteries and focuses on stationary and automotive applications.

  8. Innovation in Broad-Area Diode Laser Array Architecture: Coupling Grating-Confined Zigzag Modes for High Power, High Brightness Applications

    Science.gov (United States)

    2015-02-08

    arrays [16-18]; 3) leaky wave coupled (anti- guided ) laser arrays [7, 19-21]; 4) unstable resonators, e.g., curved mirror or tapered lasers [22-26...amplifiers. The phase of each individual amplified beam is controlled by a discrete optical phase modulator. The phase difference among the array elements...overlap area of the two gratings defines a two dimensional coupling region. The phase locking of two emitters is obtained by the wave coupling through

  9. High Power Selective Laser Melting (HP SLM) of Aluminum Parts

    Science.gov (United States)

    Buchbinder, D.; Schleifenbaum, H.; Heidrich, S.; Meiners, W.; Bültmann, J.

    Selective Laser Melting (SLM) is one of the Additive Manufacturing (AM) technologies that enables the production of light weight structured components with series identical mechanical properties without the need for part specific tooling or downstream sintering processes, etc. Especially aluminum is suited for such eco-designed components due to its low weight and superior mechanical and chemical properties. However, SLM's state-of-the-art process and cost efficiency is not yet suited for series-production. In order to improve this efficiency it is indispensable to increase the build rate significantly. Thus, aluminum is qualified for high build rate applications using a new prototype machine tool including a 1 kW laser and a multi-beam system.

  10. High Power Laser Welding. [of stainless steel and titanium alloy structures

    Science.gov (United States)

    Banas, C. M.

    1972-01-01

    A review of recent developments in high power, carbon dixoide laser welding is presented. Deep penetration welding in stainless steel to 0.5-in. thick, high speed welding in thin gage rimmed steel and gas shielded welding in Ti-6Al-4V alloy are described. The effects of laser power, power density, focusing optics, gas-shielding techniques, material properties and weld speed on weld quality and penetration are discussed. It is shown that laser welding performance in thin materials is comparable to that of electron beams. It is further shown that high quality welds, as evidenced by NDT, mechanical and metal-lographic tests, can be achieved. The potential of the laser for industrial welding applications is indicated.

  11. High-Power, High-Efficiency 1.907nm Diode Lasers Project

    Data.gov (United States)

    National Aeronautics and Space Administration — nLight developed high-power, high-efficiency laser diodes emitting at 1907nm for the pumping of solid-state lasers during the Phase I. The innovation brought to bear...

  12. High-power solid-state lasers and high-energy-density physics at CAEP

    Energy Technology Data Exchange (ETDEWEB)

    Peng, H. S.; Zhang, W. Y. [China Academy of Engineering Physics, Mianyang, Sichuan (China)

    2006-07-15

    Significant progress has been made in high-power solid-state laser development and related laser fusion and strong-field studies at the CAEP (China Academy of Engineering Physics) in recent years. A Ti:sapphire laser system, SILEX-I, was completed early in 2004 and could deliver 26- fs pulses at 300TW to targets. The SILEX-I has been operated very stably since its completion for experiments in exploring a number of frontiers, demonstrating that it is the most powerful femtosecond Ti:sapphire laser for applications in the world. The SG-III Nd:glass laser facility has been under final design to meet the requirements from laser fusion applications and will produce 3- to 5-ns pulses at 0.35 {mu}m with an output energy of about 150 kJ. The eight-beamline TIL (technical integration line), the prototype of the SG-III laser facility, has been activated in the new laboratory in Mianyang and will be completed in 2006 for operation. The SG-II laser at the Shanghai Institute of Optics and Fine Mechanics has been operating as a major facility for experiments on fusion physics since 2001. Experiments on hohlraum and implosion physics have been conducted. Simultaneously, advanced plasma diagnostic technologies for implosion hydrodynamics have been developed.

  13. Scale Law of the High Power Free Electron Laser

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The scale law and design procedure of the high power FEL are discussed. It is pointed out that theextraction efficiency, which is the critical factor of the output power besides the power of the electron

  14. Many-sided electron beam pumping of high-power lasers

    Science.gov (United States)

    Ryzhov, V. V.; Turchanovskii, I. Y.

    1997-04-01

    To study the performance of high power lasers with a many- sided electron beam injection, MUFLON-code has been developed. This code was used to choose and design optimum injection schemes for the excitation of the high-power gas lasers developed at the High Current Electronics Institute.

  15. Surface phase defects induced downstream laser intensity modulation in high-power laser facility

    Institute of Scientific and Technical Information of China (English)

    Xin Zhang; Wei Zhou; Wanjun Dai; Dongxia Hu; Xuewei Deng; Wanqing Huang; Lidan Zhou; Qiang Yuan; Xiaoxia Huang; De’en Wang; Ying Yang

    2016-01-01

    Optics surface phase defects induced intensity modulation in high-power laser facility for inertial confinement fusion research is studied. Calculations and experiments reveal an exact mapping of the modulation patterns and the optics damage spot distributions from the surface phase defects. Origins are discussed during the processes of optics manufacturing and diagnostics, revealing potential improvements for future optics manufacturing techniques and diagnostic index, which is meaningful for fusion level laser facility construction and its operation safety.

  16. The role of the gas/plasma plume and self-focusing in a gas-filled capillary discharge waveguide for high-power laser-plasma applications

    CERN Document Server

    Ciocarlan, C.; Islam, M. R.; Ersfeld, B.; Abuazoum, S.; Wilson, R.; Aniculaesei, C.; Welsh, G. H.; Vieux, G.; Jaroszynski, D. A.; 10.1063/1.4822333

    2013-01-01

    The role of the gas/plasma plume at the entrance of a gas-filled capillary discharge plasma waveguide in increasing the laser intensity has been investigated. Distinction is made between neutral gas and hot plasma plumes that, respectively, develop before and after discharge breakdown. Time-averaged measurements show that the on-axis plasma density of a fully expanded plasma plume over this region is similar to that inside the waveguide. Above the critical power, relativistic and ponderomotive selffocusing lead to an increase in the intensity, which can be nearly a factor of 2 compared with the case without a plume. When used as a laser plasma wakefield accelerator, the enhancement of intensity can lead to prompt electron injection very close to the entrance of the waveguide. Self-focusing occurs within two Rayleigh lengths of the waveguide entrance plane in the region, where the laser beam is converging. Analytical theory and numerical simulations show that, for a density of 3.01018 cm3, the peak normalized...

  17. A novel "gain chip" concept for high-power lasers (Conference Presentation)

    Science.gov (United States)

    Li, Min; Li, Mingzhong; Wang, Zhenguo; Yan, Xiongwei; Jiang, Xinying; Zheng, Jiangang; Cui, Xudong; Zhang, Xiaomin

    2017-05-01

    High-power lasers, including high-peak power lasers (HPPL) and high-average power lasers (HAPL), attract much interest for enormous variety of applications in inertial fusion energy (IFE), materials processing, defense, spectroscopy, and high-field physics research. To meet the requirements of high efficiency and quality, a "gain chip" concept is proposed to properly design the pumping, cooling and lasing fields. The gain chip mainly consists of the laser diode arrays, lens duct, rectangle wave guide and slab-shaped gain media. For the pumping field, the pump light will be compressed and homogenized by the lens duct to high irradiance with total internal reflection, and further coupled into the gain media through its two edge faces. For the cooling field, the coolant travels along the flow channel created by the adjacent slabs in the other two edge-face direction, and cool the lateral faces of the gain media. For the lasing field, the laser beam travels through the lateral faces and experiences minimum thermal wavefront distortions. Thereby, these three fields are in orthogonality offering more spatial freedom to handle them during the construction of the lasers. Transverse gradient doping profiles for HPPL and HAPL have been employed to achieve uniform gain distributions (UGD) within the gain media, respectively. This UGD will improve the management for both amplified spontaneous emission (ASE) and thermal behavior. Since each "gain chip" has its own pump source, power scaling can be easily achieved by placing identical "gain chips" along the laser beam axis without disturbing the gain and thermal distributions. To detail our concept, a 1-kJ pulsed amplifier is designed and optical-to-optical efficiency up to 40% has been obtained. We believe that with proper coolant (gas or liquid) and gain media (Yb:YAG, Nd:glass or Nd:YAG) our "gain chip" concept might provide a general configuration for high-power lasers with high efficiency and quality.

  18. On-shot laser beam diagnostics for high-power laser facility with phase modulation imaging

    Science.gov (United States)

    Pan, X.; Veetil, S. P.; Liu, C.; Tao, H.; Jiang, Y.; Lin, Q.; Li, X.; Zhu, J.

    2016-05-01

    A coherent-modulation-imaging-based (CMI) algorithm has been employed for on-shot laser beam diagnostics in high-power laser facilities, where high-intensity short-pulsed lasers from terawatt to petawatt are designed to realize inertial confinement fusion (ICF). A single-shot intensity measurement is sufficient for wave-front reconstruction, both for the near-field and far-field at the same time. The iterative reconstruction process is computationally very efficient and was completed in dozens of seconds by the additional use of a GPU device to speed it up. The compact measurement unit—including a CCD and a piece of pre-characterized phase plate—makes it convenient for focal-spot intensity prediction in the target chamber. It can be placed almost anywhere in high-power laser facilities to achieve near-field wave-front diagnostics. The feasibility of the method has been demonstrated by conducting a series of experiments with diagnostic beams and seed pulses with deactivated amplifiers in our high-power laser system.

  19. High power laser-mechanical drilling bit and methods of use

    Energy Technology Data Exchange (ETDEWEB)

    Grubb, Daryl L.; Kolachalam, Sharath K.; Faircloth, Brian O.; Rinzler, Charles C.; Allen, Erik C.; Underwood, Lance D.; Zediker, Mark S.

    2017-02-07

    An apparatus with a high power laser-mechanical bit for use with a laser drilling system and a method for advancing a borehole. The laser-mechanical bit has a beam path and mechanical removal devices that provide for the removal of laser-affected rock to advance a borehole.

  20. Target isolation system, high power laser and laser peening method and system using same

    Science.gov (United States)

    Dane, C. Brent; Hackel, Lloyd A.; Harris, Fritz

    2007-11-06

    A system for applying a laser beam to work pieces, includes a laser system producing a high power output beam. Target delivery optics are arranged to deliver the output beam to a target work piece. A relay telescope having a telescope focal point is placed in the beam path between the laser system and the target delivery optics. The relay telescope relays an image between an image location near the output of the laser system and an image location near the target delivery optics. A baffle is placed at the telescope focal point between the target delivery optics and the laser system to block reflections from the target in the target delivery optics from returning to the laser system and causing damage.

  1. Design concept and performance considerations for fast high power semiconductor switching for high repetition rate and high power excimer laser

    Science.gov (United States)

    Goto, Tatsumi; Kakizaki, Kouji; Takagi, Shigeyuki; Satoh, Saburoh; Shinohe, Takashi; Ohashi, Hiromichi; Endo, Fumihiko; Okamura, Katsuya; Ishii, Akira; Teranishi, Tsuneharu; Yasuoka, Koichi

    1997-07-01

    A semiconductor switching power supply has been developed, in which a novel structure semiconductor device, metal-oxide-semiconductor assisted gate-triggered thyristor (MAGT) was incorporated with a single stage magnetic pulse compression circuit (MPC). The MAGT was specially designed to directly replace thyratrons in a power supply for a high repetition rate laser. Compared with conventional high power semiconductor switching devices, it was designed to enable a fast switching, retaining a high blocking voltage and to extremely reduce the transient turn-on power losses, enduring a higher peak current. A maximum peak current density of 32 kA/cm2 and a current density risetime rate di/dt of 142 kA/(cm2×μs) were obtained at the chip area with an applied anode voltage of 1.5 kV. A MAGT switching unit connecting 32 MAGTs in series was capable of switching on more than 25 kV-300 A at a repetition rate of 5 kHz, which, coupled with the MPC, was equivalent to the capability of a high power thyratron. A high repetition rate and high power XeCl excimer laser was excited by the power supply. The results confirmed the stable laser operation of a repetition rate of up to 5 kHz, the world record to our knowledge. An average output power of 0.56 kW was obtained at 5 kHz where the shortage of the total discharge current was subjoined by a conventional power supply with seven parallel switching thyratrons, simultaneously working, for the MAGT power supply could not switch a greater current than that switched by one thyratron. It was confirmed by those excitations that the MAGT unit with the MPC could replace a high power commercial thyratron directly for excimer lasers. The switching stability was significantly superior to that of the thyratron in a high repetition rate region, judging from the discharge current wave forms. It should be possible for the MAGT unit, in the future, to directly switch the discharge current within a rise time of 0.1 μs with a magnetic assist.

  2. In vitro study of 960 nm high power diode laser applications in dental enamel, aided by the presence of a photoinitiator dye: scanning electron microscopy analysis; Estudo in vitro das aplicacoes do laser de diodo de alta potencia 960 nm em esmalte dentario, assistido por um fotoiniciador: analise de microscopia eletronica de varredura

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Marcelo Vinicius de

    2002-06-15

    The objective of this study is to verify if a high power diode laser can effectively modify the morphology of an enamel surface, and if this can be done in a controlled fashion by changing the lasers parameters. Previous studies using SEM demonstrated that through irradiation with Nd:YAG laser (1064 nm) it is possible to modify the morphology of the dental surface in such way as to increase its resistance against caries decays. The desired procedures that should achieve a decrease of the index of caries decays and of its sequels are on a primary level, which means that action is necessary before the disease installs itself. In this study it was used for the first time a prototype of a high power diode laser operating at 960 nm, produced by the Laboratory of Development of Lasers of the Center for Lasers and Applications of the IPEN. This equipment can present several advantages as reliability, reduced size and low cost. The aim was establish parameters of laser irradiation that produce the desired effects wanted in the enamel and protocols that guarantee its safety during application in dental hard tissues, protecting it of heating effects such as fissures and carbonization. (author)

  3. Design of measurement equipment for high power laser beam shapes

    DEFF Research Database (Denmark)

    Hansen, K. S.; Olsen, F. O.; Kristiansen, Morten

    2013-01-01

    To analyse advanced high power beam patterns, a method, which is capable of analysing the intensity distribution in 3D is needed. Further a measuring of scattered light in the same system is preferred. This requires a high signal to noise ratio. Such a system can be realised by a CCD-chip impleme......To analyse advanced high power beam patterns, a method, which is capable of analysing the intensity distribution in 3D is needed. Further a measuring of scattered light in the same system is preferred. This requires a high signal to noise ratio. Such a system can be realised by a CCD...

  4. Fibre-coupled air-cooled high-power diode laser systems

    Science.gov (United States)

    Bartoschewski, Daniel; Meinschien, Jens; Fornahl, Udo

    2008-02-01

    Current laser systems based on high-power laser diode bars need active cooling either water cooling or the use of thermo-electric coolers to ensure an adequate operating temperature for a reasonable lifetime. Here is a solution with a bonded fin heat sink and forced ventilation introduced, a diode laser bar with an improved efficiency and a low thermal resistance as well as an optical system for a highly efficient fibre coupling. With this system it is possible to couple 25 Watt continuous wave power from a single laser diode bar on a passive heat sink into a fibre with 200 μm core diameter. The basis for this performance is a heat sink with an exceptionally low thermal resistance. Several new features are introduced to reach a low overall gradient between the laser diode temperature and the ambient temperature. In addition, it does geometrically fit to the layout of the optical design. Shape and aspect ratio of both heat sink and housing of the laser system are matched to each other. Another feature is the use of hard-soldered or pressed bars to achieve a thermo-mechanically stable performance. The long-term thermal characteristic was tested. The operation temperature comes to saturation after about 30 minutes. Therefore it can be used for continuous wave operation at 25 Watt output power. At a quasi continuous operation at 70 percent duty cycle a peak power of 30 Watt out of the fibre is possible. From this technology results a compact fibre coupled laser system what is simple to drive compared with current high power laser systems, because there is no need to control the operating temperature. This gives way for more compact driver solutions. Fields of application are laser marking systems and material processing, where a simple driver system is requested. Also medical applications need this requirement and a compact cooling too so that mobile integrated solutions become possible. Further developments allow multiple laser diode systems for specific industrial

  5. Amplification of Short Pulse High Power UV Laser

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    At recent year, with the development of CPA and other amplification technology, laser intensity achieves great increase and laser power can be high to PW(105) now, this ultrashort pulse lasers offer scientists a route to investigate laser-matter interaction in an absolute new regime.So far the researches on ultrashort pulse laser-matter interaction concentrated on infrared regime, yet ultraviolet laser has the advantage in intense field physics and ICF researches for its short wavelength and less nonlinear effects. KrF excimer is the best medium in UV ultrashort pulse amplification for its small saturation energy and high contrast ratio accessible.

  6. Methods for enhancing the efficiency of creating a borehole using high power laser systems

    Science.gov (United States)

    Zediker, Mark S.; Rinzler, Charles C.; Faircloth, Brian O.; Koblick, Yeshaya; Moxley, Joel F.

    2014-06-24

    Methods for utilizing 10 kW or more laser energy transmitted deep into the earth with the suppression of associated nonlinear phenomena to enhance the formation of Boreholes. Methods for the laser operations to reduce the critical path for forming a borehole in the earth. These methods can deliver high power laser energy down a deep borehole, while maintaining the high power to perform operations in such boreholes deep within the earth.

  7. Method and system for advancement of a borehole using a high power laser

    Energy Technology Data Exchange (ETDEWEB)

    Moxley, Joel F.; Land, Mark S.; Rinzler, Charles C.; Faircloth, Brian O.; Zediker, Mark S.

    2014-09-09

    There is provided a system, apparatus and methods for the laser drilling of a borehole in the earth. There is further provided with in the systems a means for delivering high power laser energy down a deep borehole, while maintaining the high power to advance such boreholes deep into the earth and at highly efficient advancement rates, a laser bottom hole assembly, and fluid directing techniques and assemblies for removing the displaced material from the borehole.

  8. Method and apparatus for delivering high power laser energy over long distances

    Energy Technology Data Exchange (ETDEWEB)

    Zediker, Mark S; Rinzler, Charles C; Faircloth, Brian O; Koblick, Yeshaya; Moxley, Joel F

    2013-08-20

    Systems, devices and methods for the transmission of 1 kW or more of laser energy deep into the earth and for the suppression of associated nonlinear phenomena. Systems, devices and methods for the laser drilling of a borehole in the earth. These systems can deliver high power laser energy down a deep borehole, while maintaining the high power to advance such boreholes deep into the earth and at highly efficient advancement rates.

  9. Laser processes and analytics for high power 3D battery materials

    Science.gov (United States)

    Pfleging, W.; Zheng, Y.; Mangang, M.; Bruns, M.; Smyrek, P.

    2016-03-01

    Laser processes for cutting, modification and structuring of energy storage materials such as electrodes, separator materials and current collectors have a great potential in order to minimize the fabrication costs and to increase the performance and operational lifetime of high power lithium-ion-batteries applicable for stand-alone electric energy storage devices and electric vehicles. Laser direct patterning of battery materials enable a rather new technical approach in order to adjust 3D surface architectures and porosity of composite electrode materials such as LiCoO2, LiMn2O4, LiFePO4, Li(NiMnCo)O2, and Silicon. The architecture design, the increase of active surface area, and the porosity of electrodes or separator layers can be controlled by laser processes and it was shown that a huge impact on electrolyte wetting, lithium-ion diffusion kinetics, cell life-time and cycling stability can be achieved. In general, the ultrafast laser processing can be used for precise surface texturing of battery materials. Nevertheless, regarding cost-efficient production also nanosecond laser material processing can be successfully applied for selected types of energy storage materials. A new concept for an advanced battery manufacturing including laser materials processing is presented. For developing an optimized 3D architecture for high power composite thick film electrodes electrochemical analytics and post mortem analytics using laser-induced breakdown spectroscopy were performed. Based on mapping of lithium in composite electrodes, an analytical approach for studying chemical degradation in structured and unstructured lithium-ion batteries will be presented.

  10. Functionally graded materials produced with high power lasers

    NARCIS (Netherlands)

    de Hosson, J.T.M.; Pei, Y.T.; Kumar, A; Chung, YW; Moore, JJ; Doll, GL; Yatsui, K; Misra, DS

    2002-01-01

    With a well-controlled laser melt injection (LMI) process, for the first time the feasibility is demonstrated to produce SiC particles (SiCp) reinforced Ti6Al4V functionally graded materials (FGMs). SiCp are injected just behind the laser beam into the extended part of the laser melt pool that is fo

  11. Frequency doubled high-power disk lasers in pulsed and continuous-wave operation

    Science.gov (United States)

    Weiler, Sascha; Hangst, Alexander; Stolzenburg, Christian; Zawischa, Ivo; Sutter, Dirk; Killi, Alexander; Kalfhues, Steffen; Kriegshaeuser, Uwe; Holzer, Marco; Havrilla, David

    2012-03-01

    The disk laser with multi-kW output power in infrared cw operation is widely used in today's manufacturing, primarily in the automotive industry. The disk technology combines high power (average and/or peak power), excellent beam quality, high efficiency and high reliability with low investment and operating costs. Additionally, the disk laser is ideally suited for frequency conversion due to its polarized output with negligible depolarization losses. Laser light in the green spectral range (~515 nm) can be created with a nonlinear crystal. Pulsed disk lasers with green output of well above 50 W (extracavity doubling) in the ps regime and several hundreds of Watts in the ns regime with intracavity doubling are already commercially available whereas intracavity doubled disk lasers in continuous wave operation with greater than 250 W output are in test phase. In both operating modes (pulsed and cw) the frequency doubled disk laser offers advantages in existing and new applications. Copper welding for example is said to show much higher process reliability with green laser light due to its higher absorption in comparison to the infrared. This improvement has the potential to be very beneficial for the automotive industry's move to electrical vehicles which requires reliable high-volume welding of copper as a major task for electro motors, batteries, etc.

  12. Plasma-based amplification and manipulation of high-power laser pulses

    Science.gov (United States)

    Lehmann, Goetz

    2016-10-01

    In the last decade the increasing availability of Tera- and Petawatt class lasers with ps to fs pulse duration has intensified the interest in the relativistic interaction between laser radiation and matter. Today laser intensities up to 1022 W/cm2 can be achieved. Most high intensity lasers today rely on amplification schemes that can only hardly be scaled to higher power levels due to material damage thresholds. An alternative approach that allows circumventing these issues is the use of plasma as an amplification medium. Langmuir or ion waves may be used as optical components, scattering the energy from a long pump pulse into a short seed pulse. Damage thresholds of solid-state materials are not only limiting the generation of high power laser light, but also its subsequent manipulation. Again, plasma can provide an alternative approach to light manipulation. We recently proposed the concept of transient plasma photonic crystals, which aims at transferring and extending the concept of photonic crystals to the realm of plasma physics in the range of optical frequencies. In my presentation I will discuss Brillouin type plasma-based laser amplifiers and show that the ion plasma waves, driven by the two laser pulses, eventually form photonic crystals. The properties and possible future applications of these plasma photonic crystals as efficient Bragg type mirrors or polarizers will be discussed.

  13. Experiments with very high-power lasers. Report of a workshop, November 29-30, 1979

    Energy Technology Data Exchange (ETDEWEB)

    Leigh, J.; Rice, S. A.; Trainor, R. J.; Bass, M.; Hendricks, R. W.; Reader, J.

    1979-01-01

    Among possible experiments of general interest in physics are the study of the spectroscopy and cross section measurements of highly ionized species, the study of nuclear conversion processes, vacuum-ultraviolet lasers, multiphoton absorption, and the Kapitza-Dirac effect. Shock waves driven by ultrahigh-power lasers are capable of attaining pressures of the order of 1 to 4 TPa in material targets, providing a means of deriving equation-of-state data under such extreme conditions. Modifications observed in the structures of materials subjected to high-power laser radiation can lead to studies of damage and phase change processes. Classes of useful experiments in this area are given. The x rays produced when a pulse of ultrahigh-power laser radiation is focussed on a target are sufficiently intense to generate diffraction patterns and EXAFS spectra on a nanosecond time scale. A major application of ultrahigh-power lasers to chemistry and biology may consist in such time-resolved diffraction and EXAFS studies of dynamical systems. The laser systems at the National Laser User Facility at the University of Rochester are described. These systems are available to qualified investigators for user experiments.

  14. High-Power Electron Accelerators for Space (and other) Applications

    Energy Technology Data Exchange (ETDEWEB)

    Nguyen, Dinh Cong [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Lewellen, John W. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-05-23

    This is a presentation on high-power electron accelerators for space and other applications. The main points covered are: electron beams for space applications, new designs of RF accelerators, high-power high-electron mobility transistors (HEMT) testing, and Li-ion battery design. In summary, the authors have considered a concept of 1-MeV electron accelerator that can operate up to several seconds. This concept can be extended to higher energy to produce higher beam power. Going to higher beam energy requires adding more cavities and solid-state HEMT RF power devices. The commercial HEMT have been tested for frequency response and RF output power (up to 420 W). Finally, the authors are testing these HEMT into a resonant load and planning for an electron beam test in FY17.

  15. High-Power Electron Accelerators for Space (and other) Applications

    Energy Technology Data Exchange (ETDEWEB)

    Nguyen, Dinh Cong [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Lewellen, John W. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-05-23

    This is a presentation on high-power electron accelerators for space and other applications. The main points covered are: electron beams for space applications, new designs of RF accelerators, high-power HEMT testing, and battery design. In summary, we have considered a concept of 1-MeV electron accelerator that can operate up to several seconds. This concept can be extended to higher energy to produce higher beam power. Going to higher beam energy requires adding more cavities and solid-state HEMT RF power devices. The commercial HEMT have been tested for frequency response and RF output power (up to 420 W). And finally, we are testing these HEMT into a resonant load and planning for an electron beam test in FY17.

  16. Recent developments in high power thin disk lasers at TRUMPF Laser

    Science.gov (United States)

    Gottwald, Tina; Kuhn, Vincent; Schad, Sven-Silvius; Stolzenburg, Christian; Killi, Alexander

    2013-10-01

    This paper highlights the latest advances of disk laser technology at TRUMPF. The disk laser combines unique properties, especially high output brilliance (at the lowest pump brilliance requirements of any high power platform), power scalability and insensitivity to back reflections. In the latest generation of CW disk lasers, 6kW are extracted from one disk in an industrial product at beam qualities suitable for cutting and welding. Laboratory results with up to 4 kW laser power at nearly diffraction limited beam quality (M2=1.38) and 8 kW with a beam quality of 3 mm mrad from a single disk and even higher output power levels with lower beam quality will be presented. Finally, results of a frequency doubled CW disk laser will be shown.

  17. High-Efficiency High-Power Nd:YAG Laser under 885 nm Laser Diode Pumping

    Institute of Scientific and Technical Information of China (English)

    LI Fang-Qin; ZHANG Xiao-Fu; ZONG Nan; YANG Jing; PENG Qin-Jun; CUI Da-Fu; XU Zu-Yan

    2009-01-01

    A high-efficiency high-power Nd:YAG laser under 885 nm laser diode (LD) pumping is demonstrated. The laser crystal is carefully designed, and the overlapping between the pump modes and the laser modes is optimized. The maximum output power at 1064 nm is 87 W under the absorbed pump power 127.7 W, corresponding to a slope efficiency of 72.4% and an optical-optical efficiency of 68.1%. The optical-optical efficiency is 58.4% for the pump power emitted directly from the LD. To our best knowledge, this is the maximal optical-optical conversion efficiency obtained for the LD end-pumped Nd:YAG lasers so far.

  18. Laser remelting of Ti6AL4V using high power diode laser

    Science.gov (United States)

    Amaya-Vázquez, M. R.; Sánchez-Amaya, J. M.; Boukha, Z.; El Amrani, K.; Botana, F. J.

    2012-04-01

    Titanium alloys present excellent mechanical and corrosion properties, being widely employed in different industries such as medical, aerospace, automotive, petrochemical, nuclear and power generation, etc. Ti6Al4V is the α-β alloy most employed in industry. The modification of its properties can be achieved with convectional heat treatments and/or with laser processing. Laser remelting (LR) is a technology applied to Ti6Al4V by other authors with excimer and Nd-Yag laser with pure argon shielding gas to prevent risk of oxidation. In the present contribution, laser remelting has been applied for the first time to Ti6Al4V with a high power diode laser (with pure argon as shielding gas). Results showed that remelted samples (with medium energy densities) have higher microhardness and better corrosion resistance than Ti6Al4V base metal.

  19. Self-commutating converters for high power applications

    CERN Document Server

    Arrillaga, Jos; Watson, Neville R; Murray, Nicholas J

    2010-01-01

    For very high voltage or very high current applications, the power industry still relies on thyristor-based Line Commutated Conversion (LCC), which limits the power controllability to two quadrant operation. However, the ratings of self-commutating switches such as the Insulated-Gate Bipolar Transistor (IGBT) and Integrated Gate-Commutated Thyristor (IGCT), are reaching levels that make the technology possible for very high power applications. This unique book reviews the present state and future prospects of self-commutating static power converters for applications requiring either ultr

  20. DUV high power lasers processing for glass and CFRP

    Science.gov (United States)

    Kobayashi, Masakazu; Kakizaki, Kouji; Oizumi, Hiroaki; Mimura, Toshio; Fujimoto, Junichi; Mizoguchi, Hakaru

    2017-05-01

    A laser processing is widely applied to cutting, drilling, welding, bending and surface treatment in industry. Lasers with a wavelength of 1 μm are mainly used and the processing is realized by melting materials. This thermal process has a high productivity but the processed surface is hard to use for precision machining. This report is focusing on two materials which are classified in wide band gap. Ablation rate was measured with a laser microscope and an optical one. Excimer laser is expected to be a useful tool for these materials

  1. Development of a high-power blue laser (445  nm) for material processing.

    Science.gov (United States)

    Wang, Hongze; Kawahito, Yosuke; Yoshida, Ryohei; Nakashima, Yuya; Shiokawa, Kunio

    2017-06-15

    A blue diode laser has a higher absorption rate than a traditional laser, while the maximum power is limited. We report the structure and laser beam profile of a 250 W high-power blue laser (445 nm) for material processing. The absorption rate of the blue laser system for the steel was 2.75 times that of a single-mode fiber laser system (1070 nm). The characteristics of the steel after laser irradiation were determined, validating the potential of this high-power blue laser for material processing, such as heat treatment and cladding. The cost of the developed laser system was lower than that of the existing one. To the best of our knowledge, this is the first blue laser with a power as high as 250 W.

  2. High-power thulium-doped fiber laser in an all-fiber configuration

    Science.gov (United States)

    Baravets, Yauhen; Todorov, Filip; Honzatko, Pavel

    2016-12-01

    High-power Tm-doped fiber lasers are greatly suitable for various applications, such as material processing, medicine, environmental monitoring and topography. In this work we present an all-fiber narrowband CW laser in near fundamental mode operation based on a Tm-doped double-clad active fiber pumped by 793 nm laser diodes with a central wavelength stabilized at 2039 nm by a fiber Bragg grating. The achieved output power is 60 W with a slope efficiency of 46%. The measured beam quality factor is less than 1.4. Further increasing of the output power is possible using various power scaling techniques, for example, coherent combination of several Tm-doped fiber lasers. The developed fiber laser could be employed for welding, cutting and marking of thermoplastics in industry, minimally invasive surgery in medicine or sensors in lidar systems. Future improvements of thulium fiber lasers are possible due to the extremely wide gain-bandwidth of the active medium and the rapid growth of 2-μm fiber components production.

  3. Beyond blue pico laser: development of high power blue and low power direct green

    Science.gov (United States)

    Vierheilig, Clemens; Eichler, Christoph; Tautz, Sönke; Lell, Alfred; Müller, Jens; Kopp, Fabian; Stojetz, Bernhard; Hager, Thomas; Brüderl, Georg; Avramescu, Adrian; Lermer, Teresa; Ristic, Jelena; Strauss, Uwe

    2012-03-01

    There is a big need on R&D concerning visible lasers for projection applications. The pico-size mobile projection on the one hand awaits the direct green lasers with sufficiently long lifetimes at optical powers above 50mW. In this paper we demonstrate R&D-samples emitting at 519nm with lifetimes up to 10.000 hours. The business projection on the other hand requires high power operation and already uses blue lasers and phosphor conversion, but there is a strong demand for higher power levels. We investigate the power limits of R&D laser structures. In continuous wave operation, the power is limited by thermal roll-over. With an excellent power conversion efficiency of up to 29% the thermal roll-over is as high as 2.5W for a single emitter in TO56 can. We do not observe significant leakage at high currents. Driven in short pulse operation to prevent the laser from self heating, linear laser characteristics of optical power versus electrical current are observed up to almost 8W of optical power.

  4. Faraday isolator based on TSAG crystal for high power lasers.

    Science.gov (United States)

    Mironov, E A; Palashov, O V

    2014-09-22

    A Faraday isolator based on a new magneto-optical medium, TSAG (terbium scandium aluminum garnet) crystal, has been constructed and investigated experimentally. The device provides an isolation ratio of more than 30 dB at 500 W laser power. It is shown that this medium can be used in Faraday isolators for kilowatt-level laser powers.

  5. All solid-state high power visible laser

    Science.gov (United States)

    Grossman, William M.

    1993-01-01

    The overall objective of this Phase 2 effort was to develop and deliver to NASA a high repetition rate laser-diode-pumped solid-state pulsed laser system with output in the green portion of the spectrum. The laser is for use in data communications, and high efficiency, short pulses, and low timing jitter are important features. A short-pulse 1 micron laser oscillator, a new multi-pass amplifier to boost the infrared power, and a frequency doubler to take the amplified infrared pulsed laser light into the green. This produced 1.5 W of light in the visible at a pulse repetition rate of 20 kHz in the laboratory. The pulses have a full-width at half maximum of near 1 ns. The results of this program are being commercialized.

  6. An Evaluation of the Cutting Potential of Different Types of High Power Lasers

    DEFF Research Database (Denmark)

    Olsen, Flemming Ove

    2006-01-01

    Laser cutting is a widespread industrial process. The boundaries for the performance of the lasers in terms of cutting capabilities is steadily moving towards higher cutting rates and thicker section cutting. In this paper the potential of different high power laser sources in cutting is evaluate...

  7. Recent Results in High Power CO2-Laser Cutting for Shipbuilding Industry

    DEFF Research Database (Denmark)

    Olsen, Flemming Ove; Juhl, Thomas Winther; Nielsen, Jakob Skov

    2003-01-01

    In 1997 a high power laser cutting and welding test facility was established at the Danish shipyard Odense Steel Shipyard (OSS). Research and development projects were initiated in order to establish the basis for applying the full power of the laser for laser-cutting, by developing mirror based...

  8. Recent Results in High Power CO2-Laser Cutting for Shipbuilding Industry

    DEFF Research Database (Denmark)

    Olsen, Flemming Ove; Juhl, Thomas Winther; Nielsen, Jakob Skov

    2003-01-01

    In 1997 a high power laser cutting and welding test facility was established at the Danish shipyard Odense Steel Shipyard (OSS). Research and development projects were initiated in order to establish the basis for applying the full power of the laser for laser-cutting, by developing mirror based...

  9. High-power diode-pumped Tm:YLF slab laser

    CSIR Research Space (South Africa)

    Schellhorn, M

    2009-06-01

    Full Text Available The aim is to develop a high-power Tm:YLF slab laser which can be utilized to pump a Ho slab laser. A 68 W Tm:YLF slab laser was recently presented in [1] pumped from one end by a single 6-bar stack delivering ~300 W of pump power. In this work, we...

  10. High-power laser interference lithography process on photoresist: Effect of laser fluence and polarisation

    Energy Technology Data Exchange (ETDEWEB)

    Ellman, M. [CEIT and Tecnun (University of Navarra), Manuel de Lardizabal 15, 20018, San Sebastian (Spain)], E-mail: mellman@ceit.es; Rodriguez, A.; Perez, N.; Echeverria, M. [CEIT and Tecnun (University of Navarra), Manuel de Lardizabal 15, 20018, San Sebastian (Spain); Verevkin, Y.K. [Institute of Applied Physics, 46 Ul' yanova Street, 603600 Nizhny Novgorod (Russian Federation); Peng, C.S. [ORC (Tampere University of Technology), Korkeakoulunkatu 3, 33720 Tampere (Finland); Berthou, T. [SILIOS Technologies SA, Rue Gaston Imbert prolongee 13790 Peynier (France); Wang, Z. [MEC (Cardiff University), Queen' s Buildings, The Parade, Newport Road, Cardiff CF24 3AA (United Kingdom); Olaizola, S.M.; Ayerdi, I. [CEIT and Tecnun (University of Navarra), Manuel de Lardizabal 15, 20018, San Sebastian (Spain)

    2009-03-01

    High throughput and low cost fabrication techniques in the sub-micrometer scale are attractive for the industry. Laser interference lithography (LIL) is a promising technique that can produce one, two and three-dimensional periodical patterns over large areas. In this work, two- and four-beam laser interference lithography systems are implemented to produce respectively one- and two-dimensional periodical patterns. A high-power single pulse of {approx}8 ns is used as exposure process. The optimum exposure dose for a good feature patterning in a 600 nm layer of AZ-1505 photoresist deposited on silicon wafers is studied. The best aspect ratio is found for a laser fluence of 20 mJ/cm{sup 2}. A method to control the width of the sub-micrometer structures based on controlling the resist thickness and the laser fluence is proposed.

  11. Reliability of high power laser diodes with external optical feedback

    Science.gov (United States)

    Bonsendorf, Dennis; Schneider, Stephan; Meinschien, Jens; Tomm, Jens W.

    2016-03-01

    Direct diode laser systems gain importance in the fields of material processing and solid-state laser pumping. With increased output power, also the influence of strong optical feedback has to be considered. Uncontrolled optical feedback is known for its spectral and power fluctuation effects, as well as potential emitter damage. We found that even intended feedback by use of volume Bragg gratings (VBG) for spectral stabilization may result in emitter lifetime reduction. To provide stable and reliable laser systems design, guidelines and maximum feedback ratings have to be found. We present a model to estimate the optical feedback power coupled back into the laser diode waveguide. It includes several origins of optical feedback and wide range of optical elements. The failure thresholds of InGaAs and AlGaAs bars have been determined not only at standard operation mode but at various working points. The influence of several feedback levels to laser diode lifetime is investigated up to 4000h. The analysis of the semiconductor itself leads to a better understanding of the degradation process by defect spread. Facet microscopy, LBIC- and electroluminescence measurements deliver detailed information about semiconductor defects before and after aging tests. Laser diode protection systems can monitor optical feedback. With this improved understanding, the emergency shutdown threshold can be set low enough to ensure laser diode reliability but also high enough to provide better machine usability avoiding false alarms.

  12. High-Power, High-Efficiency 1.907nm Diode Lasers Project

    Data.gov (United States)

    National Aeronautics and Space Administration — nLight proposes to develop high-power, high-efficiency laser diodes emitting at 1907nm. Performance is expected to improve from the current state-of-the-art...

  13. Efficient high power 2 micron Tm3+-Doped Fiber Laser Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This proposal is for the development of new Tm3+ doped germanate glass fibers for efficient high power 2 micron fiber lasers capable of generating an output power of...

  14. Efficient High Power 2 micron Tm3+-Doped Fiber Laser Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This proposal is for the development of new Tm3+ doped germanate glass fibers for efficient high power 2-micron fiber lasers capable of generating an output power of...

  15. New frontiers in nuclear physics with high-power lasers and brilliant monochromatic gamma beams

    Science.gov (United States)

    Gales, S.; Balabanski, D. L.; Negoita, F.; Tesileanu, O.; Ur, C. A.; Ursescu, D.; Zamfir, N. V.

    2016-09-01

    The development of high power lasers and the combination of such novel devices with accelerator technology has enlarged the science reach of many research fields, in particular particle and nuclear physics, astrophysics as well as societal applications in material science, nuclear energy and applications for medicine. The European Strategic Forum for Research Infrastructures has selected a proposal based on these new premises called the Extreme Light Infrastructure (ELI). The ELI will be built as a network of three complementary pillars at the frontier of laser technologies. The ELI-NP pillar (NP for nuclear physics) is under construction near Bucharest (Romania) and will develop a scientific program using two 10 PW lasers and a Compton back-scattering high-brilliance and intense low-energy gamma beam, a combination of laser and accelerator technology at the frontier of knowledge. This unique combination of beams that are unique worldwide allows us to develop an experimental program in nuclear physics at the frontiers of present-day knowledge as well as society driven applications. In the present paper, the technical description of the facility as well as the new perspectives in nuclear structure, nuclear reactions and nuclear astrophysics will be presented.

  16. Relativistic high-power laser-matter interactions

    Energy Technology Data Exchange (ETDEWEB)

    Salamin, Yousef I. [Max-Planck-Institute for Nuclear Physics, Saupfercheckweg 1, D-69117 Heidelberg (Germany); Physics Department, American University of Sharjah, POB 26666, Sharjah (United Arab Emirates); Hu, S.X. [Group T-4, Theoretical Division, MS B283, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Hatsagortsyan, Karen Z. [Max-Planck-Institute for Nuclear Physics, Saupfercheckweg 1, D-69117 Heidelberg (Germany); Department of Quantum Electronics, Yerevan State University, A. Manoukian 1, Yerevan 375025 (Armenia); Keitel, Christoph H. [Max-Planck-Institute for Nuclear Physics, Saupfercheckweg 1, D-69117 Heidelberg (Germany)]. E-mail: keitel@mpi-hd.mpg.de

    2006-04-15

    Recent advances in laser technology have pushed the frontier of maximum intensity achieved to about 10{sup 22}W/cm{sup 2} and investigators currently believe even higher intensities may be reached in the near future. This, combined with other breakthroughs on the fronts of short pulse generation and high repetition rates, have stimulated considerable progress, theoretical as well as experimental, in the field of laser-matter interactions. It is now possible to laser-accelerate electrons to a few hundred MeV and laser-induced pair-production and nuclear physics experiments have made significant progress. This article is devoted to a review of the recent advances in the field and stresses quantum phenomena that require laser field intensities in excess of the relativistic threshold of {approx}10{sup 18}W/cm{sup 2}. Interactions with free electrons, with highly-charged ions and with atoms and clusters, are reviewed. Electron laser acceleration, atomic quantum dynamics, high harmonic generation, quantum electrodynamical effects and nuclear interactions in plasmas and ions, are among the important topics covered in the article.

  17. Ultra-sensitive Absorption Diagnostics of Thin Films for High-power Laser Interference Coatings

    Science.gov (United States)

    2015-01-05

    Absorption Diagnostics of Thin Films for High-power Laser Interference Coatings REPORT DOCUMENTATION PAGE Form Approved OMB No. 0704-0188 Public...Absorption Diagnostics of Thin Films for High-power Laser Interference Coatings FA9550-13-1-0201 Jorge J. Rocca (PI) Oscar E. Martinez Carmen S...work consists of the development of a prototype suitable for incorporation into the deposition chamber. Such powerful diagnostics does not

  18. Electron Dynamics During High-Power, Short-Pulsed Laser Interactions with Solids and Interfaces

    Science.gov (United States)

    2016-06-28

    PAPER ALSO RECEIVED EXTERNAL MEDIA COVERENCE FROM SIGNAL MAGAZINE : http://www.afcea.org/content/?q=Article-scientists-harness- energy -heat Edited...AFRL-AFOSR-VA-TR-2016-0234 Electron Dynamics During High- Power , Short-Pulsed Laser Interactions with Solids and Interfaces Patrick Hopkins...Dynamics During High- Power , Short-Pulsed Laser Interactions with Solids and Interfaces 5a. CONTRACT NUMBER FA9550-13-1-0067 5b. GRANT NUMBER 5c

  19. Optical fiber cable for transmission of high power laser energy over great distances

    Science.gov (United States)

    Zediker, Mark S.; Rinzler, Charles C.; Faircloth, Brian O.; Moxley, Joel F.; Koblick, Yeshaya

    2016-05-24

    There is provided a system and apparatus for the transmission of high power laser energy over great distances without substantial power loss and without the presence of stimulated Raman scattering. There is further provided systems and optical fiber cable configurations and optical fiber structures for the delivering high power laser energy over great distances to a tool or surface to perform an operation or work with the tool or upon the surface.

  20. Optical Properties of Lithium Terbium Fluoride and Implications for Performance in High Power Lasers (Postprint)

    Science.gov (United States)

    2016-02-01

    AFRL-RX-WP-JA-2016-0323 OPTICAL PROPERTIES OF LITHIUM TERBIUM FLUORIDE AND IMPLICATIONS FOR PERFORMANCE IN HIGH POWER LASERS...DATE (DD-MM-YY) 2. REPORT TYPE 3. DATES COVERED (From - To) 16 October 2015 Interim 6 May 2010 – 16 September 2015 4. TITLE AND SUBTITLE...OPTICAL PROPERTIES OF LITHIUM TERBIUM FLUORIDE AND IMPLICATIONS FOR PERFORMANCE IN HIGH POWER LASERS (POSTPRINT) 5a. CONTRACT NUMBER IN-HOUSE 5b

  1. Optical fiber cable for transmission of high power laser energy over great distances

    Energy Technology Data Exchange (ETDEWEB)

    Zediker, Mark S.; Rinzler, Charles C.; Faircloth, Brian O.; Moxley, Joel F.; Koblick, Yeshaya

    2016-05-24

    There is provided a system and apparatus for the transmission of high power laser energy over great distances without substantial power loss and without the presence of stimulated Raman scattering. There is further provided systems and optical fiber cable configurations and optical fiber structures for the delivering high power laser energy over great distances to a tool or surface to perform an operation or work with the tool or upon the surface.

  2. A simple method for timing an XFEL source to high-power lasers

    Energy Technology Data Exchange (ETDEWEB)

    Geloni, G.; Saldin, E.; Schneidmiller, E.; Yurkov, M.

    2007-12-15

    We propose a technique, to be used for time-resolved pump-probe experiments, for timing an X-ray free electron laser (XFEL) to a high-power conventional laser with femtosecond accuracy. Our method takes advantage of the same electron bunch to produce both an XFEL pulse and an ultrashort optical pulse with the help of an optical radiator downstream of the X-ray undulator. Since both pulses are produced by the same electron bunch, they are perfectly synchronized. Application of cross-correlation techniques will allow to determine relative jitter between the optical pulse (and, thus, the XFEL pulse) and a pulse from an external pump-laser with femtosecond resolution. Technical realization of the proposed timing scheme uses an optical replica synthesizer (ORS) setup to be installed after the final bunch compression stage of the XFEL. The electron bunch is modulated in the ORS setup by an external optical laser. Subsequently, it travels through the main undulator, and produces the XFEL pulse. Finally, a powerful optical pulse of coherent edge radiation is generated as the bunch passes through a long straight section and a separation magnet downstream of the main undulator. Our study shows that at a moderate (about 10%) density modulation of the electron bunch at the location of the optical radiator allows production of high power X-ray and optical pulses. Relative synchronization of these pulses is preserved by using the samemechanical support for both X-ray and optical elements transporting radiation down to the experimental area, where single-shot cross-correlation between optical pulse and pump-laser pulse is performed. We illustrate the potential of the proposed timing technique with numerical examples referring to the European XFEL facility. (orig.)

  3. Design Challenges in High Power Free-Electron Laser Oscillators

    CERN Document Server

    Benson, S V

    2005-01-01

    Several FELs have now demonstrated high power lasing and several projects are under construction to deliver higher power or shorter wavelengths. This presentation will summarize progress in upgrading FEL oscillators towards higher power and will discuss some of the challenges these projects face. The challenges fall into three categories: 1. energy recovery with large exhaust energy spread, 2. output coupling and maintaining mirror figure in the presence of high intracavity power loading, and 3. high current operation in an energy recovery linac (ERL). Progress in all three of these areas has been made in the last year. Energy recovery of over 12% of exhaust energy spread has been demonstrated and designs capable of accepting even larger energy spreads have been proposed. Cryogenic transmissive output couplers for narrow band operation and both hole and scraper output coupling have been developed. Investigation of short Rayleigh range operation has started as well. Energy recovery of over 20 mA CW has been de...

  4. Relay telescope for high power laser alignment system

    Science.gov (United States)

    Dane, C. Brent; Hackel, Lloyd; Harris, Fritz B.

    2006-09-19

    A laser system includes an optical path having an intracavity relay telescope with a telescope focal point for imaging an output of the gain medium between an image location at or near the gain medium and an image location at or near an output coupler for the laser system. A kinematic mount is provided within a vacuum chamber, and adapted to secure beam baffles near the telescope focal point. An access port on the vacuum chamber is adapted for allowing insertion and removal of the beam baffles. A first baffle formed using an alignment pinhole aperture is used during alignment of the laser system. A second tapered baffle replaces the alignment aperture during operation and acts as a far-field baffle in which off angle beams strike the baffle a grazing angle of incidence, reducing fluence levels at the impact areas.

  5. Efficient High Power Ho,Tm:GdVO4 Laser

    Institute of Scientific and Technical Information of China (English)

    WANG Yue-Zhu; ZHU Guo-Li; JU You-Lun; YAO Bao-Quan

    2011-01-01

    We report a 22.3 W cw diode-pumped cryogenic Ho(0.5at. %), Tm(at.5%):GdVC>4 laser at a wavelength of 2.05 fzm. It is pumped by two fiber-coupled laser diodes with a fiber core diameter of 0.4 mm, both of which provide 42 W pump power near 802 nm. A cw output power of 22.3 W was obtained at the pump power of 51.0 W, corresponding to an optical-to-optical conversion efficiency of 43.7% when the ratio of the pump beam to oscillating laser beam in the crystal was ^1.33:1. The M2 factor was found to be 2.0 under an output power of 16.5 W.%@@ We report a 22.3 W ew diode-pumped cryogenic Ho(0.5at.%),Tm(at.5%):GdVO4 laser at a wavelength of 2.05μm.It is pumped by two fiber-coupled laser diodes with a fiber core diameter of 0.4 mm,both of which provide 42W pump power near 802 nm.A cw output power of 22.3 W was obtained at the pump power of 51.0W,corresponding to an optical-to-optical conversion efficiency of 43.7%when the ratio of the pump beam to oscillating laser beam in the crystal was ~1.33:1.The M2 factor was found to be 2.0 under an output power of 16.5 W.

  6. High power 355 nm diode-pumped solid-state laser

    Science.gov (United States)

    Yu, Yang; Cheng, Chee Yuen; Peng, Xiaoyuan; Yong, Saw Soon

    2015-07-01

    This paper reported a high-power diode-pumped solid-state laser for material processing applications with a target of more than 60 ns pulse width at 355 nm. As known, long pulse width IR laser (around 70-100 ns) is difficult to get high conversion efficiency to UV since the peak power is more than 2 times lower than 20-30 ns laser. However, the unique long pulse width characteristic makes the laser an ideal tool for flexible PCB drilling with 30-50 μm holes and for cutting portable devices. Up to 52.2% IR to UV conversion efficiency was obtained by our novel intra-cavity harmonic generation cavity design. A 9.3W UV output at 30 kHz was demonstrated with compact intra-cavity sum frequency design. Special conduction cooling-designed LD side-pumped module provided 17.8 W fundamental IR output power with AOM q-switching. The UV output pulse width is 76 ns at 30 kHz and 140 ns at 70 kHz. The type I and type II phase matching LBOs were used for intra-cavity harmonic generations of 355 nm. The output characteristics of the IR and the harmonic generations varying with the pulse repetition rate were also investigated. The experimental results are in agreement with the theoretical modelling. This system will also be useful for many material processing applications such as PCB cutting and wafer scribing.

  7. High Power Diode Lasers with External Feedback: Overview and Prospects

    DEFF Research Database (Denmark)

    Chi, Mingjun; Petersen, Paul Michael

    2012-01-01

    In summary, different external-cavity feedback techniques to improve the spatial beam quality and narrow the linewidth of the output beam from both BALs and TDLs are presented. Broad-area diode laser system with external-cavity feedback around 800 nm can produce several Watts of output power...

  8. Two dimensional simulation of high power laser-surface interaction

    Energy Technology Data Exchange (ETDEWEB)

    Goldman, S.R.; Wilke, M.D.; Green, R.E.L.; Johnson, R.P. [Los Alamos National Lab., NM (United States); Busch, G.E. [KMS Fusion, Inc., Ann Arbor, MI (United States)

    1998-08-01

    For laser intensities in the range of 10{sup 8}--10{sup 9} W/cm{sup 2}, and pulse lengths of order 10 {micro}sec or longer, the authors have modified the inertial confinement fusion code Lasnex to simulate gaseous and some dense material aspects of the laser-matter interaction. The unique aspect of their treatment consists of an ablation model which defines a dense material-vapor interface and then calculates the mass flow across this interface. The model treats the dense material as a rigid two-dimensional mass and heat reservoir suppressing all hydrodynamic motion in the dense material. The computer simulations and additional post-processors provide predictions for measurements including impulse given to the target, pressures at the target interface, electron temperatures and densities in the vapor-plasma plume region, and emission of radiation from the target. The authors will present an analysis of some relatively well diagnosed experiments which have been useful in developing their modeling. The simulations match experimentally obtained target impulses, pressures at the target surface inside the laser spot, and radiation emission from the target to within about 20%. Hence their simulational technique appears to form a useful basis for further investigation of laser-surface interaction in this intensity, pulse-width range. This work is useful in many technical areas such as materials processing.

  9. High-power non linear frequency converted laser diodes

    DEFF Research Database (Denmark)

    Jensen, Ole Bjarlin; Andersen, Peter E.; Hansen, Anders Kragh;

    2015-01-01

    We present different methods of generating light in the blue-green spectral range by nonlinear frequency conversion of tapered diode lasers achieving state-of-the-art power levels. In the blue spectral range, we show results using single-pass second harmonic generation (SHG) as well as cavity...

  10. The generation and amplification of intergalactic magnetic fields in analogue laboratory experiments with high power lasers

    Science.gov (United States)

    Gregori, G.; Reville, B.; Miniati, F.

    2015-11-01

    The advent of high-power laser facilities has, in the past two decades, opened a new field of research where astrophysical environments can be scaled down to laboratory dimensions, while preserving the essential physics. This is due to the invariance of the equations of magneto-hydrodynamics to a class of similarity transformations. Here we review the relevant scaling relations and their application in laboratory astrophysics experiments with a focus on the generation and amplification of magnetic fields in cosmic environment. The standard model for the origin of magnetic fields is a multi stage process whereby a vanishing magnetic seed is first generated by a rotational electric field and is then amplified by turbulent dynamo action to the characteristic values observed in astronomical bodies. We thus discuss the relevant seed generation mechanisms in cosmic environment including resistive mechanism, collision-less and fluid instabilities, as well as novel laboratory experiments using high power laser systems aimed at investigating the amplification of magnetic energy by magneto-hydrodynamic (MHD) turbulence. Future directions, including efforts to model in the laboratory the process of diffusive shock acceleration are also discussed, with an emphasis on the potential of laboratory experiments to further our understanding of plasma physics on cosmic scales.

  11. Real-time power measurement and control for high power diode laser

    Science.gov (United States)

    Qin, Wen-bin; Liu, You-qiang; Cao, Yin-hua; Wang, Zhi-yong

    2011-06-01

    As the continual improvement of technology and beam quality, diode laser, with poor beam quality, no longer just apply to pump solid-state laser. As a kind of implement of laser materials processing, high-power diode laser has been used in manufacture, as a brand new means of laser processing. Due to the influence of inevitable unstable factors, for example, the temperature of water-cooler, the current of power supply, etc, the output power of diode laser will be unstable. And laser output power, as an important parameter, frequently affects the performance of the laser beam and the experimental results of processing, especially in the laser materials processing. Therefore, researching the real-time power measurement and control of high power diode laser has great significance, and for diode laser, it would improve performance of itself. To achieve the purpose of real-time detection, traditional measuring method, placing a power sensor behind the total-reflection mirror of laser resonant cavity, is mainly applied in the system of gas laser and solid-state laser. However, Owing to the high integration level of diode laser, traditional measuring method can't be adopted. A technique for real-time measure output power of high power diode laser is developed to improve quality of the laser in this paper. A lens placed at an angle of 45° in the system was used to sample output light of laser, and a piece of ground glass was used to uniform the beam power density, then the photoelectric detector received an optic signal and converted it into electric signal. This feeble signal was processed by amplification circuit with a filter. Finally, this detected electric signal was applied to accomplish the closed-loop control of power. The performance of power measurement and control system was tested with the 300W diode laser, and the measuring inaccuracy achieved was less than +/-1%.

  12. Shock propagation and attenuation in high-power excimer lasers

    Science.gov (United States)

    Holzwarth, Achim; Berger, Peter; Huegel, Helmut

    1993-05-01

    Theoretical and experimental investigations on the propagation, reflection, and attenuation of shock waves as they occur in excimer lasers have been performed. The numerical simulations have been carried out using a two-dimensional, unsteady finite difference scheme. The experimental setup is a piston driven shock tube with a rectangular cross section working in air at atmospheric pressure. The shocks were detected interferometrically as well as by means of pressure transducers. This shock tube allows us to investigate basic phenomena of shock diffraction which can be used to confirm the computational results in the range of weak shock waves. In particular, the influence of the shape of the wall contour on the reflection of shock waves has been investigated theoretically. The decay time of pressure and density perturbations differs for various wall configurations in such a way that short electrodes accelerate the attenuation as well as does a strong area increase in the vicinity of them. After each laser pulse there is a shock travelling into the laser channel. Experiments have been carried out on the reflection of this shock at a specially formed bend that is able to focus the shock into a muffling element.

  13. High power laser heating of low absorption materials

    Energy Technology Data Exchange (ETDEWEB)

    Olson, K.; Talghader, J., E-mail: joey@umn.edu [Electrical Engineering, University of Minnesota, Minneapolis, Minnesota 55455 (United States); Ogloza, A. [Naval Postgraduate School, 1 University Cir, Monterey, California 93943 (United States); Thomas, J. [Electro Optics Center, Pennsylvania State University, 222 Northpointe Blvd., Freeport, Pennsylvania 16229 (United States)

    2014-09-28

    A model is presented and confirmed experimentally that explains the anomalous behavior observed in continuous wave (CW) excitation of thermally isolated optics. Distributed Bragg Reflector (DBR) high reflective optical thin film coatings of HfO₂ and SiO₂were prepared with a very low absorption, about 7 ppm, measured by photothermal common-path interferometry. When illuminated with a 17 kW CW laser for 30 s, the coatings survived peak irradiances of 13 MW/cm², on 500 μm diameter spot cross sections. The temperature profile of the optical surfaces was measured using a calibrated thermal imaging camera for illuminated spot sizes ranging from 500 μm to 5 mm; about the same peak temperatures were recorded regardless of spot size. This phenomenon is explained by solving the heat equation for an optic of finite dimensions and taking into account the non-idealities of the experiment. An analytical result is also derived showing the relationship between millisecond pulse to CW laser operation where (1) the heating is proportional to the laser irradiance (W/m²) for millisecond pulses, (2) the heating is proportional to the beam radius (W/m) for CW, and (3) the heating is proportional to W/m∙ tan⁻¹(√(t)/m) in the transition region between the two.

  14. Photonic bandgap fiber lasers and multicore fiber lasers for next generation high power lasers

    DEFF Research Database (Denmark)

    Shirakawa, A.; Chen, M.; Suzuki, Y.

    2014-01-01

    Photonic bandgap fiber lasers are realizing new laser spectra and nonlinearity mitigation that a conventional fiber laser cannot. Multicore fiber lasers are a promising tool for power scaling by coherent beam combination. © 2014 OSA.......Photonic bandgap fiber lasers are realizing new laser spectra and nonlinearity mitigation that a conventional fiber laser cannot. Multicore fiber lasers are a promising tool for power scaling by coherent beam combination. © 2014 OSA....

  15. Proton acceleration in the interaction of high power laser and cryogenic hydrogen targets

    Science.gov (United States)

    Mishra, Rohini; Fiuza, Frederico; Glenzer, Siegfried

    2014-10-01

    High intensity laser driven ion acceleration has attracted great interest due to many prospective applications ranging from inertial confinement fusion, cancer therapy, particle accelerators. Particle-in-Cell (PIC) simulations are performed to model and design experiments at MEC for high power laser interaction with cryogenic hydrogen targets of tunable density and thickness. Preliminary 1D and 2D simulations, using fully relativistic particle-in-cell code PICLS, show a unique regime of proton acceleration, e.g. ~ 300 MeV peak energy protons are observed in the 1D run for interaction of ~1020 W/cm2, 110 fs intense laser with 6nc dense (nc = 1021 cm-3) and 2 micron thin target. The target is relativistically under-dense for the laser and we observe that a strong (multi-terawatt) shock electric field is produced and protons are reflected to high velocities by this field. Further, the shock field and the laser field keep propagating through the hydrogen target and meets up with target normal sheath acceleration (TNSA) electric field produced at the target rear edge and vacuum interface and this superposition amplifies the TNSA fields resulting in higher proton energy. In addition, the electrons present at the rear edge of the target continue to gain energy via strong interaction with laser that crosses the target and these accelerated electrons maintains higher electric sheath fields which further provides acceleration to protons. We will also present detailed investigation with 2D PICLS simulations to gain a better insight of such physical processes to characterize multidimensional effects and establish analytical scaling between laser and target conditions for the optimization of proton acceleration.

  16. Cladding glass ceramic for use in high powered lasers

    Science.gov (United States)

    Marker, Alexander J.; Campbell, John H.

    1998-01-01

    A Cu-doped/Fe-doped low expansion glass ceramic composition comprising in Wt. %: SiO{sub 2} 50--65; Al{sub 2}O{sub 3} 18--27; P{sub 2}O{sub 5} 0--10; Li{sub 2}O 2--6; Na{sub 2}O 0--2; K{sub 2}O 0--2; B{sub 2}O{sub 3} 0--1; MgO 0--4; ZnO 0--5; CaO 0--4; BaO 0--5; TiO{sub 2} 1--3; ZrO{sub 3} 1--3; As{sub 2}O{sub 3} 0--1.5; Sb{sub 2}O{sub 3} 0--1.5; CuO 0--3; and Fe{sub 2}O{sub 3} 0--1 wherein the total amount of SiO{sub 2}, Al{sub 2}O{sub 3} and P{sub 2}O{sub 5} is 80--89 wt. %, and said glass ceramic contains as a dopant 0.1--3 wt. % CuO, 0.1--1 wt. % Fe{sub 2}O{sub 3} or a combined CuO+Fe{sub 2}O{sub 3} amount of 0.1--4 wt. %. The glass ceramic composition is suitable for use as a cladding material for solid laser energy storage mediums as well as for use in beam attenuators for measuring laser energy level and beam blocks or beam dumps used for absorbing excess or unused laser energy.

  17. Water Vapour Propulsion Powered by a High-Power Laser-Diode

    Science.gov (United States)

    Minami, Y.; Uchida, S.

    Most of the laser propulsion schemes now being proposed and developed assume neither power supplies nor on-board laser devices and therefore are bound to remote laser stations like a kite via a laser beam “string”. This is a fatal disadvantage for a space vehicle that flies freely though it is often said that no need of installing an energy source is an advantage of a laser propulsion scheme. The possibility of an independent laser propulsion space vehicle that carries a laser source and a power supply on board is discussed. This is mainly due to the latest development of high power laser diode (LD) technology. Both high specific impulse-low thrust mode and high thrust-low specific impulse mode can be selected by controlling the laser output by using vapour or water as a propellant. This mode change can be performed by switching between a high power continuous wave (cw), LD engine for high thrust with a low specific impulse mode and high power LD pumping Q-switched Nd:YAG laser engine for low thrust with the high specific impulse mode. This paper describes an Orbital Transfer Vehicle equipped with the above-mentioned laser engine system and fuel cell that flies to the Moon from a space platform or space hotel in Earth orbit, with cargo shipment from lunar orbit to the surface of the Moon, including the possibility of a sightseeing trip.

  18. Investigations into the Feasibility of High Power Laser Window Materials

    Science.gov (United States)

    1975-04-15

    1, 1 ,4 ) l r i gtVII Ir nIf t:trl;l (:l w illi the. ,.,l .q. ,I 1h. el,.1i , ’l lay 4 ,,, t r,11 I itll the htod r in 1,i.* shape of a nuY.z.le, with...K/J. On substituting this result in (B7) we find that for short, flat topped laser pulses, = a E T Jp/Zd S for 2r < d r 1 E T J /8) -- r Zr > d ( B10

  19. Big solar furnace as pumping source for high power lasers

    Science.gov (United States)

    Payziyev, Sh.; Bakhramov, S.; Klichev, Sh.; Kasimov, A.; Riskiev, T.; Abdurakhmanov, A.; Fazilov, A.

    2008-02-01

    For effective conversion of the energy of the concentrated solar flux of 1 MW Big Solar Furnace of the Scientific and Production Association "Physics-Sun" (Tashkent) with focal spot size of about 40 cm into the coherent laser radiation, the several designs of the multi-element secondary concentrators for various active mediums with different thermal and optical characteristics were considered. For calculations of parameters of secondary concentrators the Ray tracing and Monte-Carlo methods were used and the numerical experiments were performed.

  20. Development of fluorides for high power laser optics

    Energy Technology Data Exchange (ETDEWEB)

    Ready, J.F.; Vora, H.

    1980-07-01

    The laser-assisted thermonuclear fusion program has significant needs for improved optical materials with high transmission in the ultraviolet, and with low values of nonlinear index of refraction. Lithium fluoride (LiF) possesses a combination of optical properties which are of potential use. Single-crystalline LiF is limited by low mechanical strength. In this program, we investigated the technique of press-forging to increase the mechanical strength. LiF single crystals were press-forged over the temperature range 300 to 600/sup 0/C to produce fine-grained polycrystalline material.

  1. High-Power ZBLAN Glass Fiber Lasers: Review and Prospect

    OpenAIRE

    Xiushan Zhu; Peyghambarian, N.

    2010-01-01

    ZBLAN (ZrF4-BaF2-LaF3-AlF3-NaF), considered as the most stable heavy metal fluoride glass and the excellent host for rare-earth ions, has been extensively used for efficient and compact ultraviolet, visible, and infrared fiber lasers due to its low intrinsic loss, wide transparency window, and small phonon energy. In this paper, the historical progress and the properties of fluoride glasses and the fabrication of ZBLAN fibers are briefly described. Advances of infrared, upconversion, and supe...

  2. High-power distributed Bragg reflector lasers for green-light generation

    Science.gov (United States)

    Hu, Martin H.; Nguyen, Hong Ky; Song, Kechang; Li, Yabo; Visovsky, Nick J.; Liu, Xingsheng; Nishiyama, Nobuhiko; Coleman, Sean; Hughes, Lawrence C., Jr.; Gollier, Jacques; Miller, William; Bhat, Raj; Zah, Chung-En

    2006-02-01

    We report on the design, fabrication and performance of high-power and high-modulation-speed 1060-nm DBR lasers for green-light emission by second harmonic generation. Single-spatial-mode and single-wavelength power more than 450 mW of 1060-nm wavelength was achieved with a 3-section DBR laser with non-absorbing DBR and phase sections created by an impurity-free quantum-well intermixing technique. A thermally-induced wavelength tuning of 2.4 nm and a carrier-induced wavelength tuning of -0.85 nm were obtained by injecting current into the DBR section. The green power as high as 104.6 mW was demonstrated by coupling the DBR laser output to a second-harmonic-generation waveguide. Measured rise/fall times of 0.2 ns for direct intensity modulation and 0.6 ns for wavelength modulation make the DBR lasers suitable for >=50-MHz green-light-modulation applications. The detrimental thermally-induced patterning effect and a differential-phase modulation scheme as a solution are discussed.

  3. A simple method for timing an XFEL source to high-power lasers

    CERN Document Server

    Geloni, Gianluca; Schneidmiller, Evgeni; Yurkov, Mikhail

    2007-01-01

    We propose a technique, to be used for time-resolved pump-probe experiments, for timing an x-ray free electron laser (XFEL) to a high-power conventional laser with femtosecond accuracy. Our method takes advantage of the same electron bunch to produce both an XFEL pulse and an ultrashort optical pulse with the help of an optical radiator downstream of the x-ray undulator. Since both pulses are produced by the same electron bunch, they are perfectly synchronized. Application of cross-correlation techniques will allow to determine relative jitter between the optical pulse (and, thus, the XFEL pulse) and a pulse from an external pump-laser with femtosecond resolution. Technical realization of the proposed timing scheme uses an optical replica synthesizer (ORS) setup to be installed after the final bunch-compression stage of the XFEL. The electron bunch is modulated in the ORS setup by an external optical laser. Subsequently, it travels through the main undulator, and produces the XFEL pulse. Finally, a powerful o...

  4. Rugged passively cooled high power laser fiber optic connectors and methods of use

    Energy Technology Data Exchange (ETDEWEB)

    Rinzler, Charles C.; Gray, William C.; Fraze, Jason D.; Faircloth, Brian O.; Zediker, Mark S.; McKay, Ryan P.

    2016-06-07

    There are provided high power laser connectors and couplers and methods that are capable of providing high laser power without the need for active cooling to remote, harsh and difficult to access locations and under difficult and harsh conditions and to manage and mitigate the adverse effects of back reflections.

  5. Design of an Optical System for High Power CO2 Laser Cutting

    DEFF Research Database (Denmark)

    de Lange, D.F.; Meijer, J.; Nielsen, Jakob Skov

    2003-01-01

    The results of a design study for the optical system for cutting with high power CO2 lasers (6 kW and up) will be presented. As transparent materials cannot be used for these power levels, mirrors have been applied. A coaxial cutting gas supply has been designed with a laser beam entrance into th...

  6. Rugged passively cooled high power laser fiber optic connectors and methods of use

    Energy Technology Data Exchange (ETDEWEB)

    Rinzler, Charles C.; Gray, William C.; Fraze, Jason D.; Faircloth, Brian O.; Zediker, Mark S.; McKay, Ryan P.

    2016-06-07

    There are provided high power laser connectors and couplers and methods that are capable of providing high laser power without the need for active cooling to remote, harsh and difficult to access locations and under difficult and harsh conditions and to manage and mitigate the adverse effects of back reflections.

  7. Nd:YAG Ceramic ThinZag (registered trademark) High-Power Laser Development

    Science.gov (United States)

    2011-01-01

    CHAPTER 9 Nd:YAG Ceramic ThinZag® High-Power Laser Development Daniel E. Klimek Principal Research Scientist, Textron Defense Systems, Wilmington...ThinZag High-Power Laser Development 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER...Power Laser Development N d : Y A G C e r a m i c T h i n Z a g ® H i g h - P o w e r L a s e r D e v e l o p m e n t 209 over the years at

  8. High power ring methods and accelerator driven subcritical reactor application

    Energy Technology Data Exchange (ETDEWEB)

    Tahar, Malek Haj [Univ. of Grenoble (France)

    2016-08-07

    transverse beam dynamics. The results obtained allow to develop a correction scheme to minimize the tune variations of the FFAG. This is the cornerstone of a new fixed tune non-scaling FFAG that represents a potential candidate for high power applications. As part of the developments towards high power at the KURRI FFAG, beam dynamics studies have to account for space charge effects. In that framework, models have been installed in the tracking code ZGOUBI to account for the self-interaction of the particles in the accelerator. Application to the FFAG studies is shown. Finally, one focused on the ADSR concept as a candidate to solve the problem of nuclear waste. In order to establish the accelerator requirements, one compared the performance of ADSR with other conventional critical reactors by means of the levelized cost of energy. A general comparison between the different accelerator technologies that can satisfy these requirements is finally presented. In summary, the main drawback of the ADSR technology is the high Levelized Cost Of Energy compared to other advanced reactor concepts that do not employ an accelerator. Nowadays, this is a show-stopper for any industrial application aiming at producing energy (without dealing with the waste problem). Besides, the reactor is not intrinsically safer than critical reactor concepts, given the complexity of managing the target interface between the accelerator and the reactor core.

  9. Recent development on high-power tandem-pumped fiber laser

    Science.gov (United States)

    Zhou, Pu; Xiao, Hu; Leng, Jinyong; Zhang, Hanwei; Xu, Jiangmin; Wu, Jian

    2016-11-01

    High power fiber laser is attracting more and more attention due to its advantage in excellent beam quality, high electricto- optical conversion efficiency and compact system configuration. Power scaling of fiber laser is challenged by the brightness of pump source, nonlinear effect, modal instability and so on. Pumping active fiber by using high-brightness fiber laser instead of common laser diode may be the solution for the brightness limitation. In this paper, we will present the recent development of various kinds of high power fiber laser based on tandem pumping scheme. According to the absorption property of Ytterbium-doped fiber, Thulium-doped fiber and Holmium-doped fiber, we have theoretically studied the fiber lasers that operate at 1018 nm, 1178 nm and 1150 nm, respectively in detail. Consequently, according to the numerical results we have optimized the fiber laser system design, and we have achieved (1) 500 watt level 1018nm Ytterbium-doped fiber laser (2) 100 watt level 1150 nm fiber laser and 100 watt level random fiber laser (3) 30 watt 1178 nm Ytterbium-doped fiber laser, 200 watt-level random fiber laser. All of the above-mentioned are the record power for the corresponded type of fiber laser to the best of our knowledge. By using the high-brightness fiber laser operate at 1018 nm, 1178 nm and 1150 nm that we have developed, we have achieved the following high power fiber laser (1) 3.5 kW 1090 nm Ytterbium-doped fiber amplifier (2) 100 watt level Thulium-doped fiber laser and (3) 50 watt level Holmium -doped fiber laser.

  10. Experimental astrophysics with high power lasers and Z pinches

    Energy Technology Data Exchange (ETDEWEB)

    Remington, B A; Drake, R P; Ryutov, D D

    2004-12-10

    With the advent of high energy density (HED) experimental facilities, such as high-energy lasers and fast Z-pinch, pulsed-power facilities, mm-scale quantities of matter can be placed in extreme states of density, temperature, and/or velocity. This has enabled the emergence of a new class of experimental science, HED laboratory astrophysics, wherein the properties of matter and the processes that occur under extreme astrophysical conditions can be examined in the laboratory. Areas particularly suitable to this class of experimental astrophysics include the study of opacities relevant to stellar interiors; equations of state relevant to planetary interiors; strong shock driven nonlinear hydrodynamics and radiative dynamics, relevant to supernova explosions and subsequent evolution; protostellar jets and high Mach-number flows; radiatively driven molecular clouds and nonlinear photoevaporation front dynamics; and photoionized plasmas relevant to accretion disks around compact objects, such as black holes and neutron stars.

  11. Laboratory Astrophysics on High Power Lasers and Pulsed Power Facilities

    Energy Technology Data Exchange (ETDEWEB)

    Remington, B A

    2002-02-05

    Over the past decade a new genre of laboratory astrophysics has emerged, made possible by the new high energy density (HED) experimental facilities, such as large lasers, z-pinch generators, and high current particle accelerators. (Remington, 1999; 2000; Drake, 1998; Takabe, 2001) On these facilities, macroscopic collections of matter can be created in astrophysically relevant conditions, and its collective properties measured. Examples of processes and issues that can be experimentally addressed include compressible hydrodynamic mixing, strong shock phenomena, radiative shocks, radiation flow, high Mach-number jets, complex opacities, photoionized plasmas, equations of state of highly compressed matter, and relativistic plasmas. These processes are relevant to a wide range of astrophysical phenomena, such as supernovae and supernova remnants, astrophysical jets, radiatively driven molecular clouds, accreting black holes, planetary interiors, and gamma-ray bursts. These phenomena will be discussed in the context of laboratory astrophysics experiments possible on existing and future HED facilities.

  12. Ion Cleaning of Facets for Improving the Reliability of High Power 980 nm Semiconductor Lasers

    Institute of Scientific and Technical Information of China (English)

    SHU Xiong-Wen; XU Chen; TIAN Zeng-Xia; SHEN Guang-Di

    2006-01-01

    We report a simple and available way of improving the reliability of high power InGaAs 980 nm lasers by cleaning the facets using Ar ion before the protecting films have been coated. The Ar cleaning can remove the impurity and the oxide on the air-cleaved facets of laser diodes. It is proven that the way has marked effect on reducing the gradual degradation rate of laser diodes and improving the catastrophic-optical-damage threshold.

  13. High power all-solid-state quasi-continuous-wave tunable Ti: sapphire laser system

    Institute of Scientific and Technical Information of China (English)

    Lei Zou; Xin Ding; Yue Zou; Hongmei Ma; Wuqi Wen; Peng Wang; Jianquan Yao

    2005-01-01

    This paper reports a high power, all-solid-state, quasi-continuous-wave tunable Ti:sapphire laser system pumped by laser diode (LD) pumped frequency-doubled Nd:YAG laser. The maximum tuned output power of 4.2 W (797 nm) and tuned average power of 3.7 W were achieved when fixing the Ti:sapphire broadband output power at 5.0 W and applying 750-850 nm broadband coated mirror.

  14. High Efficiency Power Converter for Low Voltage High Power Applications

    DEFF Research Database (Denmark)

    Nymand, Morten

    , and remote power generation for light towers, camper vans, boats, beacons, and buoys etc. A review of current state-of-the-art is presented. The best performing converters achieve moderately high peak efficiencies at high input voltage and medium power level. However, system dimensioning and cost are often......The topic of this thesis is the design of high efficiency power electronic dc-to-dc converters for high-power, low-input-voltage to high-output-voltage applications. These converters are increasingly required for emerging sustainable energy systems such as fuel cell, battery or photo voltaic based...... determined by the performance at the system worst case operating point which is usually at minimum input voltage and maximum power. Except for the non-regulating V6 converters, all published solutions exhibit a very significant drop in conversion efficiency at minimum input voltage and maximum output power...

  15. Refractive beam shapers for material processing with high power single mode and multimode lasers

    Science.gov (United States)

    Laskin, Alexander; Laskin, Vadim

    2013-02-01

    The high power multimode fiber-coupled laser sources, like solid state lasers or laser diodes as well as single mode and multimode fiber lasers, are now widely used in various industrial laser material processing technologies like metal or plastics welding, cladding, hardening, brazing, annealing. Performance of these technologies can be essentially improved by varying the irradiance profile of a laser beam with using beam shaping optics, for example, the field mapping refractive beam shapers like piShaper. Operational principle of these devices presumes transformation of laser beam irradiance distribution from Gaussian to flattop, super-Gauss, or inverse-Gauss profile with high flatness of output wave front, conserving of beam consistency, providing collimated output beam of low divergence, high transmittance, extended depth of field. Important feature of piShaper is in capability to operate with TEM00 and multimode lasers, the beam shapers can be implemented not only as telescopic optics but also as collimating systems, which can be connected directly to fiber-coupled lasers or fiber lasers, thus combining functions of beam collimation and irradiance transformation. This paper will describe some features of beam shaping of high-power laser sources, including multimode fiber coupled lasers, and ways of adaptation of beam shaping optical systems design to meet requirements of modern laser technologies. Examples of real implementations will be presented as well.

  16. Fiber laser pumped high power mid-infrared laser with picosecond pulse bunch output.

    Science.gov (United States)

    Wei, Kaihua; Chen, Tao; Jiang, Peipei; Yang, Dingzhong; Wu, Bo; Shen, Yonghang

    2013-10-21

    We report a novel quasi-synchronously pumped PPMgLN-based high power mid-infrared (MIR) laser with picosecond pulse bunch output. The pump laser is a linearly polarized MOPA structured all fiberized Yb fiber laser with picosecond pulse bunch output. The output from a mode-locked seed fiber laser was directed to pass through a FBG reflector via a circulator to narrow the pulse duration from 800 ps to less than 50 ps and the spectral FWHM from 9 nm to 0.15 nm. The narrowed pulses were further directed to pass through a novel pulse multiplier through which each pulse was made to become a pulse bunch composing of 13 sub-pulses with pulse to pulse time interval of 1.26 ns. The pulses were then amplified via two stage Yb fiber amplifiers to obtain a linearly polarized high average power output up to 85 W, which were then directed to pass through an isolator and to pump a PPMgLN-based optical parametric oscillator via quasi-synchronization pump scheme for ps pulse bunch MIR output. High MIR output with average power up to 4 W was obtained at 3.45 micron showing the feasibility of such pump scheme for ps pulse bunch MIR output.

  17. Injection locking of a low cost high power laser diode at 461 nm

    OpenAIRE

    Pagett, C. J. H.; Moriya, P. H.; Teixeira, R. Celistrino; Shiozaki, R. F.; Hemmerling, M.; Courteille, Ph. W.

    2016-01-01

    Stable laser sources at 461 nm are important for optical cooling of strontium atoms. In most existing experiments this wavelength is obtained by frequency doubling infrared lasers, since blue laser diodes either have low power or large emission bandwidths. Here, we show that injecting less than 10 mW of monomode laser radiation into a blue multimode 500 mW high power laser diode is capable of slaving at least 50% of the power to the desired frequency. We verify the emission bandwidth reductio...

  18. Toward realizing high power semiconductor terahertz laser sources at room temperature

    Science.gov (United States)

    Razeghi, Manijeh

    2011-05-01

    The terahertz (THz) spectral range offers promising applications in science, industry, and military. THz penetration through nonconductors (fabrics, wood, plastic) enables a more efficient way of performing security checks (for example at airports), as illegal drugs and explosives could be detected. Being a non-ionizing radiation, THz radiation is environment-friendly enabling a safer analysis environment than conventional X-ray based techniques. However, the lack of a compact room temperature THz laser source greatly hinders mass deployment of THz systems in security check points and medical centers. In the past decade, tremendous development has been made in GaAs/AlGaAs based THz Quantum Cascade Laser (QCLs), with maximum operating temperatures close to 200 K (without magnetic field). However, higher temperature operation is severely limited by a small LO-phonon energy (~ 36 meV) in this material system. With a much larger LO-phonon energy of ~ 90 meV, III-Nitrides are promising candidates for room temperature THz lasers. However, realizing high quality material for GaN-based intersubband devices presents a significant challenge. Advances with this approach will be presented. Alternatively, recent demonstration of InP based mid-infrared QCLs with extremely high peak power of 120 W at room temperature opens up the possibility of producing high power THz emission with difference frequency generation through two mid-infrared wavelengths.

  19. High power laser for peening of metals enabling production technology

    Energy Technology Data Exchange (ETDEWEB)

    Daly, J.; Dane, C.B.; Hackel, L.A.; Harrison, J.

    1998-06-18

    Cryogenic energy-dispersive x-ray detectors are being developed because of their superior energy resolution ((less than or equal to) 10 eV FWHM for keV x rays) compared to semiconductor EDS systems. So far, their range of application is limited due to their comparably small size and low count rate. We present data on the development of superconducting tunnel junction (STJ) detector arrays to address both of these issues. A single STJ detector has a resolution around 10 eV below 1 keV and can be operated at count rates of order 10,000 counts/s. We show that the simultaneous operation of several STJ detectors does not diminish their energy resolution significantly, while increasing the detector area and the maximum count rate by a factor given by the total number of independent channels.

  20. Widely Tunable High-Power Tapered Diode Laser at 1060 nm

    DEFF Research Database (Denmark)

    Jensen, Ole Bjarlin; Sumpf, Bernd; Erbert, Götz

    2011-01-01

    We report a large tuning range from 1018 to 1093 nm from a InGaAs single quantum-well 1060-nm external cavity tapered diode laser. More than 2.5-W output power has been achieved. The tuning range is to our knowledge the widest obtained from a high-power InGaAs single quantum-well tapered laser op...... operating around 1060 nm. The light emitted by the laser has a nearly diffraction limited beam quality and a narrow linewidth of less than 6 pm everywhere in the tuning range.......We report a large tuning range from 1018 to 1093 nm from a InGaAs single quantum-well 1060-nm external cavity tapered diode laser. More than 2.5-W output power has been achieved. The tuning range is to our knowledge the widest obtained from a high-power InGaAs single quantum-well tapered laser...

  1. Equipment, preliminary research and research opportunities at the High Power Laser Laboratory at Institute of Plasma Physics and Laser Microfusion

    Science.gov (United States)

    Rosinski, M.; Zaras-Szydlowska, A.; Parys, P.; Gasior, P.; Ryc, L.; Badziak, J.

    2014-11-01

    The aim of this paper is to describe the newly-opened High Power Laser Laboratory (HPLL) at the Institute of Plasma Physics and Laser Microfusion (IPPLM) and presents its research possibilities in terms of the laser source and the available diagnostics. The interactions of the ultra-short laser pulses of femto to pico second duration and energies of up to 1 J with solid-state targets leads to very distinguish phenomena which can be used for investigation of exotic states of matter and to apply them for numerous technological purposes. in this goal the application of sophisticated and especially designed diagnostic systems is also needed. As the effects of interactions include the broad range of processes as acceleration of fast ions and electrons, x-rays generation and solid material modification in terms of its mechanical, physical and optical properties the research needs to use both online plasma diagnostics and the methods of post-mortem material research characterization methods. The paper presents a brief description of the laser system, the interaction vacuum chambers and the available diagnostics as well as the scientific investigation trends which can be picked up at the HPLL at the IPPLM.

  2. High-power diode laser marking and engraving of building materials

    Science.gov (United States)

    Li, Lin; Lawrence, Jonathan; Spencer, Julian T.

    1997-08-01

    A Diomed 60W-cw high power diode laser (HPDL) has been used for the marking and engraving of various building materials, including; marble, granite, clay tiles, ceramic tiles, roof tiles, ordinary Portland cement (OPC) and clay bricks. Morphological and microstructural characteristics have been investigated. The basic mechanism of marking/engraving and the characteristics of the beam absorption are discussed. The effects of material texture, color and laser processing parameters are reported. The work shows that engraving depths of over 2 mm (0.75 mm for a single pass) can be achieved on marble substrates by thermal disintegration of CaCO3 into loose CaO powder and CO2 gas. Uniform amorphous glazed lines (1 - 3 mm line width) of a color different from the untreated materials can be generated on clay tiles, ceramic tiles, roof tiles, clay bricks and OPC by solidification phase formation after laser melting of these materials. Effects of atmospheric conditions, for instance using O2 and Ar gas shrouds, have been examined, with different colored marks being observed when different shroud gases are used. To demonstrate the practical worth of the process a UMIST crest has been marked on a ceramic tile using the system. Laser beam reflectivity is found to depend not only on material composition but also its color. Reflectivity has been found to range between 12% to 18% for the various construction materials used in the experiment, except for marble (grey) which showed over 27% reflectivity. Since the HPDL is a portable device, on-site application of these processing techniques can be realized, which would be either impossible or difficult when using other types of lasers.

  3. Beam shaping design for coupling high power diode laser stack to fiber.

    Science.gov (United States)

    Ghasemi, Seyed Hamed; Hantehzadeh, Mohammad-Reza; Sabbaghzadeh, Jamshid; Dorranian, Davoud; Lafooti, Majid; Vatani, Vahid; Rezaei-Nasirabad, Reza; Hemmati, Atefeh; Amidian, Ali Asghar; Alavian, Seyed Ali

    2011-06-20

    A beam shaping technique that rearranges the beam for improving the beam symmetry and power density of a ten-bar high power diode laser stack is simulated considering a stripe mirror plate and a V-Stack mirror in the beam shaping system. In this technique, the beam of a high power diode laser stack is effectively coupled into a standard 550 μm core diameter and a NA=0.22 fiber. By this technique, compactness, higher efficiency, and lower cost production of the diode are possible.

  4. Cascaded quadratic soliton compression of high-power femtosecond fiber lasers in Lithium Niobate crystals

    DEFF Research Database (Denmark)

    Bache, Morten; Moses, Jeffrey; Wise, Frank W.

    2008-01-01

    The output of a high-power femtosecond fiber laser is typically 300 fs with a wavelength around $\\lambda=1030-1060$ nm. Our numerical simulations show that cascaded quadratic soliton compression in bulk LiNbO$_3$ can compress such pulses to below 100 fs.......The output of a high-power femtosecond fiber laser is typically 300 fs with a wavelength around $\\lambda=1030-1060$ nm. Our numerical simulations show that cascaded quadratic soliton compression in bulk LiNbO$_3$ can compress such pulses to below 100 fs....

  5. Self-biased circulators for high power applications

    Science.gov (United States)

    Sokolov, Alexander S.

    Self-biased circulators exploit the properties of high anisotropy magnetic field in hexagonal ferrites, thus allowing operation without biasing magnets and a significant size and weight reduction. Although first self-biased circulators were demonstrated more than 20 years ago, all the prototypes constructed so far are unsuitable for practical applications. An attempt to design a self-biased circulator from scratch was made. Novel exceptionally low dielectric loss and high heat conductivity ceramic materials were developed and innovative substrate synthesis techniques were employed. Low temperature cofiring of green body ferrite compacts and dielectric ceramic slurries were mastered, resulting in solid composite substrates. Original device design was developed. Key features (including wide coupling angles, wide microstriplines, thick substrate, and absence of impedance transformers) enable low insertion loss, broadband operation, high power handling, and compact size. Fabrication and testing of Ka band Y-junction self-biased circulator are reported herein. Furthermore, design approach and fabrication techniques developed here can be readily applied for the construction of X-band self-biased circulators, provided that suitable ferrite materials are available. Low temperature cofiring of ferrite and dielectric materials is especially beneficial for various RF and high-frequency applications. Multiple devices can be readily fabricated on a single wafer using conventional lithographic techniques, resulting in true microwave monolithic integrated circuit.

  6. High-Power Continuous-Wave Directly-Diode-Pumped Fiber Raman Lasers

    Directory of Open Access Journals (Sweden)

    Tianfu Yao

    2015-11-01

    Full Text Available We describe novel fiber Raman lasers pumped directly by spectrally combined high power multimode laser diodes at 975 nm and emitting at 1019 nm. With a commercial multimode graded-index fiber, we reached 20 W of laser output power with a record slope efficiency of 80%. With an in-house double-clad fiber, the beam quality improved to M2 = 1.9, albeit with lower output power and slope efficiency due to higher fiber loss. We believe this is the first publication of a fiber Raman laser cladding-pumped directly by diodes.

  7. High-power AlGaAs channeled substrate planar diode lasers for spaceborne communications

    Science.gov (United States)

    Connolly, J. C.; Goldstein, B.; Pultz, G. N.; Slavin, S. E.; Carlin, D. B.; Ettenberg, M.

    1988-01-01

    A high power channeled substrate planar AlGaAs diode laser with an emission wavelength of 8600 to 8800 A was developed. The optoelectronic behavior (power current, single spatial and spectral behavior, far field characteristics, modulation, and astigmatism properties) and results of computer modeling studies on the performance of the laser are discussed. Lifetest data on these devices at high output power levels is also included. In addition, a new type of channeled substrate planar laser utilizing a Bragg grating to stabilize the longitudinal mode was demonstrated. The fabrication procedures and optoelectronic properties of this new diode laser are described.

  8. High power diode laser array development using completely indium free packaging technology with narrow spectrum

    Science.gov (United States)

    Hou, Dong; Wang, Jingwei; Gao, Lijun; Liang, Xuejie; Li, Xiaoning; Liu, Xingsheng

    2016-03-01

    The high power diode lasers have been widely used in many fields. In this work, a sophisticated high power and high performance horizontal array of diode laser stacks have been developed and fabricated with high duty cycle using hard solder bonding technology. CTE-matched submount and Gold Tin (AuSn) hard solder are used for bonding the diode laser bar to achieve the performances of anti-thermal fatigue, higher reliability and longer lifetime. This array consists of 30 bars with the expected optical output peak power of 6000W. By means of numerical simulation and analytical results, the diode laser bars are aligned on suitable positions along the water cooled cooler in order to achieve the uniform wavelength with narrow spectrum and accurate central wavelength. The performance of the horizontal array, such as output power, spectrum, thermal resistance, life time, etc., is characterized and analyzed.

  9. Hollow-core photonic crystal fibre for high power laser beam delivery

    Institute of Scientific and Technical Information of China (English)

    Yingying; Wang; Meshaal; Alharbi; Thomas; D.Bradley; Coralie; Fourcade-Dutin; Benot; Debord; Benot; Beaudou; Frdric; Ger??me; Fetah; Benabid

    2013-01-01

    We review the use of hollow-core photonic crystal fibre(HC-PCF)for high power laser beam delivery.A comparison of bandgap HC-PCF with Kagome-lattice HC-PCF on the geometry,guidance mechanism,and optical properties shows that the Kagome-type HC-PCF is an ideal host for high power laser beam transportation because of its large core size,low attenuation,broadband transmission,single-mode guidance,low dispersion and the ultra-low optical overlap between the core-guided modes and the silica core-surround.The power handling capability of Kagome-type HC-PCF is further experimentally demonstrated by millijoule nanosecond laser spark ignition and~100μJ sub-picosecond laser pulse transportation and compression.

  10. An ultra short pulse reconstruction software applied to the GEMINI high power laser system

    Energy Technology Data Exchange (ETDEWEB)

    Galletti, Mario, E-mail: mario.gall22@gmail.com [INFN – LNF, Via Enrico Fermi 40, 00044 Frascati (Italy); Galimberti, Marco [Central Laser Facility, Rutherford Appleton Laboratory, Didcot (United Kingdom); Hooker, Chris [Central Laser Facility, Rutherford Appleton Laboratory, Didcot (United Kingdom); University of Oxford, Oxford (United Kingdom); Chekhlov, Oleg; Tang, Yunxin [Central Laser Facility, Rutherford Appleton Laboratory, Didcot (United Kingdom); Bisesto, Fabrizio Giuseppe [INFN – LNF, Via Enrico Fermi 40, 00044 Frascati (Italy); Curcio, Alessandro [INFN – LNF, Via Enrico Fermi 40, 00044 Frascati (Italy); Sapienza – University of Rome, P.le Aldo Moro, 2, 00185 Rome (Italy); Anania, Maria Pia [INFN – LNF, Via Enrico Fermi 40, 00044 Frascati (Italy); Giulietti, Danilo [Physics Department of the University and INFN, Pisa (Italy)

    2016-09-01

    The GRENOUILLE traces of Gemini pulses (15 J, 30 fs, PW, shot per 20 s) were acquired in the Gemini Target Area PetaWatt at the Central Laser Facility (CLF), Rutherford Appleton Laboratory (RAL). A comparison between the characterizations of the laser pulse parameters made using two different types of algorithms: Video Frog and GRenouille/FrOG (GROG), was made. The temporal and spectral parameters came out to be in great agreement for the two kinds of algorithms. In this experimental campaign it has been showed how GROG, the developed algorithm, works as well as VideoFrog algorithm with the PetaWatt pulse class. - Highlights: • Integration of the diagnostic tool on high power laser. • Validation of the GROG algorithm in comparison to a well-known commercial available software. • Complete characterization of the GEMINI ultra-short high power laser pulse.

  11. Thermooptical processes in the window of a high-power gas laser

    Science.gov (United States)

    Rogozhin, M. V.; Rogalin, V. E.; Krymskii, M. I.

    2017-05-01

    We have developed a mathematical model of thermomechanical and thermooptical processes that proceed in the output window of a continuous gas laser of a multikilowatt power. Optimal parameters have been determined at which the output window not only successfully withstands an extreme radiation load, but also ensures the radiation coupling with a minimum possible divergence. We have used numerical modeling to analyze the properties of the most promising materials used in high-power CO2, CO, and oxygen-iodine lasers.

  12. Frequency-stabilized diode-pumped Nd:YAG laser of high power

    Energy Technology Data Exchange (ETDEWEB)

    Taccheo, S.; Laporta, P.; Longhi, S. [CNR, Milano (Italy). Centro di Elettronica Quantistica e Strumentazione Elettronica]|[Politecnico di Milano (Italy). Dipt. di Fisica; Svelto, C. [Politecnico di Milano (Italy). Dipt. di Elettronica e Informazione

    1995-09-01

    The authors describe a frequency-stabilized diode-pumped Nd:YAG laser of high power whose single-mode operation is obtained by suppressing the spatial hole burning through the twisted-mode technique. Active frequency stabilization is achieved by fringe side locking the laser beam to a reference Fabry-Perot cavity. Output power up to 800 mW in single-transverse and -longitudinal mode operation with a linewidth of less than 20 kHz is obtained.

  13. First lasing at the high-power free electron laser at Siberian center for photochemistry research

    Science.gov (United States)

    Antokhin, E. A.; Akberdin, R. R.; Arbuzov, V. S.; Bokov, M. A.; Bolotin, V. P.; Burenkov, D. B.; Bushuev, A. A.; Veremeenko, V. F.; Vinokurov, N. A.; Vobly, P. D.; Gavrilov, N. G.; Gorniker, E. I.; Gorchakov, K. M.; Grigoryev, V. N.; Gudkov, B. A.; Davydov, A. V.; Deichuli, O. I.; Dementyev, E. N.; Dovzhenko, B. A.; Dubrovin, A. N.; Evtushenko, Yu. A.; Zagorodnikov, E. I.; Zaigraeva, N. S.; Zakutov, E. M.; Erokhin, A. I.; Kayran, D. A.; Kiselev, O. B.; Knyazev, B. A.; Kozak, V. R.; Kolmogorov, V. V.; Kolobanov, E. I.; Kondakov, A. A.; Kondakova, N. L.; Krutikhin, S. A.; Kryuchkov, A. M.; Kubarev, V. V.; Kulipanov, G. N.; Kuper, E. A.; Kuptsov, I. V.; Kurkin, G. Ya.; Labutskaya, E. A.; Leontyevskaya, L. G.; Loskutov, V. Yu.; Matveenko, A. N.; Medvedev, L. E.; Medvedko, A. S.; Miginsky, S. V.; Mironenko, L. A.; Motygin, S. V.; Oreshkov, A. D.; Ovchar, V. K.; Osipov, V. N.; Persov, B. Z.; Petrov, S. P.; Petrov, V. M.; Pilan, A. M.; Poletaev, I. V.; Polyanskiy, A. V.; Popik, V. M.; Popov, A. M.; Rotov, E. A.; Salikova, T. V.; Sedliarov, I. K.; Selivanov, P. A.; Serednyakov, S. S.; Skrinsky, A. N.; Tararyshkin, S. V.; Timoshina, L. A.; Tribendis, A. G.; Kholopov, M. A.; Cherepanov, V. P.; Shevchenko, O. A.; Shteinke, A. R.; Shubin, E. I.; Scheglov, M. A.

    2004-08-01

    The first lasing near wavelength 140 μm was achieved in April 2003 on a high-power free electron laser (FEL) constructed at the Siberian Center for Photochemical Research. In this paper, we briefly describe the design of FEL driven by an accelerator-recuperator. Characteristics of the electron beam and terahertz laser radiation, obtained at the first experiments, are also presented in the paper.

  14. Model of small-scale self-focusing and spatial noise in high power laser driver

    Institute of Scientific and Technical Information of China (English)

    HU; Wei(胡巍); FU; Xiquan(傅喜泉); YU; Song; (喻松); GUO; Hong(郭弘)

    2002-01-01

    A linearization model was used to analyze the laser beam propagation in a high power laser driver and the influence of the small-scale self-focusing and spatial phase noise on beam quality in disk amplifiers. The quantitative relations between intensities of spatial phase noise, B-integral, and beam intensity contrast in near field are given explicitly. A spectrum specification of phase noise has been obtained by setting a limit to the contrast of an output beam.

  15. Study of the high power laser-metal interactions in the gaseous atmospheres

    Science.gov (United States)

    Lugomer, Stjepan; Bitelli, G.; Stipancic, M.; Jovic, F.

    1994-08-01

    The tantalum and titanium plates were treated by pulsed, high power CO2 laser in the pressurized atmospheres of N2 and O2. Studies performed by the optical microscopy, microhardness measurements, and the auger electron spectroscopy revealed: (1) topographic modification of the surface caused by the temperature field; (2) metal hardening, caused by the laser shock; and (3) alloying/cladding, caused by the chemical reaction between the metal surface and the gaseous atmosphere.

  16. Status of the high power free electron laser using the race-track microtron-recuperator

    Science.gov (United States)

    Vinokurov, N. A.; Gavrilov, N. G.; Gorniker, E. I.; Kulipanov, G. N.; Kuptsov, I. V.; Kurkin, G. Ya.; Erg, G. I.; Levashov, Yu. I.; Oreshkov, A. D.; Petrov, S. P.; Petrov, V. M.; Pinayev, I. V.; Popik, V. M.; Sedlyarov, I. K.; Shaftan, T. V.; Skrinsky, A. N.; Sokolov, A. S.; Veshcherevich, V. G.; Vobly, P. D.

    1996-02-01

    The high power infrared free electron laser is under construction at the Novosibirsk Scientific Centre. The goal of this project is to provide a user facility for Siberian Centre of Photochemical Researches. The features of the installation and its status are described.

  17. Microstructural evolution in additive manufacturing with high power lasers : Deposition, characterization and performance

    NARCIS (Netherlands)

    Nenadl, Ondrej

    2017-01-01

    High power lasers provide time and cost effective method for metallic surface modification. In this work these modifications are explored as: 1) a simple melting and subsequent rapid solidification of a metallic surface – resulting in superior properties post-treatment; 2) deposition of an

  18. Tribological and mechanical properties of high power laser surface-treated metallic glasses

    NARCIS (Netherlands)

    Matthews, D. T. A.; Ocelik, V.; de Hosson, J. Th. M.

    2007-01-01

    The processing power of high power Nd:YAG laser has been utilised to achieve the inherently high cooling rates required to form many of today's bulk metallic glasses (BMGs). The production of thick (>= 250 mu m) amorphous surface layers has been considered. Microstructural and chemical observation t

  19. Computer simulation of effect of conditions on discharge-excited high power gas flow CO laser

    Science.gov (United States)

    Ochiai, Ryo; Iyoda, Mitsuhiro; Taniwaki, Manabu; Sato, Shunichi

    2017-01-01

    The authors have developed the computer simulation codes to analyze the effect of conditions on the performances of discharge excited high power gas flow CO laser. The six be analyzed. The simulation code described and executed by Macintosh computers consists of some modules to calculate the kinetic processes. The detailed conditions, kinetic processes, results and discussions are described in this paper below.

  20. Degradation Processes in High-Power Diode Lasers under External Optical Feedback

    DEFF Research Database (Denmark)

    Tomm, Jens. W.; Hempel, Martin; Petersen, Paul Michael;

    2013-01-01

    The effect of moderate external feedback on the gradual degradation of 808 nm emitting AlGaAs-based high-power broad-area diode lasers is analyzed. Eventually the quantum well that actually experiences the highest total optical load remains unaffected by the aging, while severe impact...

  1. Microstructural evolution in additive manufacturing with high power lasers : Deposition, characterization and performance

    NARCIS (Netherlands)

    Nenadl, Ondrej

    2017-01-01

    High power lasers provide time and cost effective method for metallic surface modification. In this work these modifications are explored as: 1) a simple melting and subsequent rapid solidification of a metallic surface – resulting in superior properties post-treatment; 2) deposition of an additiona

  2. Semiconductor laser engineering, reliability and diagnostics a practical approach to high power and single mode devices

    CERN Document Server

    Epperlein, Peter W

    2013-01-01

    This reference book provides a fully integrated novel approach to the development of high-power, single-transverse mode, edge-emitting diode lasers by addressing the complementary topics of device engineering, reliability engineering and device diagnostics in the same book, and thus closes the gap in the current book literature. Diode laser fundamentals are discussed, followed by an elaborate discussion of problem-oriented design guidelines and techniques, and by a systematic treatment of the origins of laser degradation and a thorough exploration of the engineering means to enhance the optical strength of the laser. Stability criteria of critical laser characteristics and key laser robustness factors are discussed along with clear design considerations in the context of reliability engineering approaches and models, and typical programs for reliability tests and laser product qualifications. Novel, advanced diagnostic methods are reviewed to discuss, for the first time in detail in book literature, performa...

  3. Injection locking of a low cost high power laser diode at 461 nm

    CERN Document Server

    Pagett, C J H; Teixeira, R C; Shiozaki, R F; Hemmerling, M; Courteille, Ph W

    2016-01-01

    Stable laser sources at 461 nm are important for optical cooling of strontium atoms. In most existing experiments this wavelength is obtained by frequency doubling infrared lasers, since blue laser diodes either have low power or large emission bandwidths. Here, we show that injecting less than 10 mW of monomode laser radiation into a blue multimode 500 mW high power laser diode is capable of slaving at least 50% of the power to the desired frequency. We verify the emission bandwidth reduction by saturation spectroscopy on a strontium gas cell and by direct beating of the slave with the master laser. We also demonstrate that the laser can efficiently be used within the Zeeman slower for optical cooling of a strontium atomic beam.

  4. Injection locking of a low cost high power laser diode at 461 nm

    Science.gov (United States)

    Pagett, C. J. H.; Moriya, P. H.; Celistrino Teixeira, R.; Shiozaki, R. F.; Hemmerling, M.; Courteille, Ph. W.

    2016-05-01

    Stable laser sources at 461 nm are important for optical cooling of strontium atoms. In most existing experiments, this wavelength is obtained by frequency doubling infrared lasers, since blue laser diodes either have low power or large emission bandwidths. Here, we show that injecting less than 10 mW of monomode laser radiation into a blue multimode 500 mW high power laser diode is capable of slaving at least 50% of the power to the desired frequency. We verify the emission bandwidth reduction by saturation spectroscopy on a strontium gas cell and by direct beating of the slave with the master laser. We also demonstrate that the laser can efficiently be used within the Zeeman slower for optical cooling of a strontium atomic beam.

  5. A High Power and High Repetition Rate Modelocked Ti-Sapphire Laser for Photoinjectors

    Energy Technology Data Exchange (ETDEWEB)

    J. Hansknecht; M. Poelker

    2001-07-01

    A high power cw mode-locked Ti-sapphire laser has been constructed to drive the Jefferson Lab polarized photoinjector and provide > 500 mW average power with 50 ps pulsewidths at 499 MHz or 1497 MHz pulse repetition rates. This laser allows efficient, high current synchronous photoinjection for extended periods of time before intrusive steps must be taken to restore the quantum efficiency of the strained layer GaAs photocathode. The use of this laser has greatly enhanced the maximum high polarization beam current capability and operating lifetime of the Jefferson Lab photoinjector compared with previous performance using diode laser systems. A novel modelocking technique provides a simple means to phase-lock the optical pulse train of the laser to the accelerator and allows for operation at higher pulse repetition rates to {approx} 3 GHz without modification of the laser cavity. The laser design and characteristics are described below.

  6. Injection locking of a low cost high power laser diode at 461 nm.

    Science.gov (United States)

    Pagett, C J H; Moriya, P H; Celistrino Teixeira, R; Shiozaki, R F; Hemmerling, M; Courteille, Ph W

    2016-05-01

    Stable laser sources at 461 nm are important for optical cooling of strontium atoms. In most existing experiments, this wavelength is obtained by frequency doubling infrared lasers, since blue laser diodes either have low power or large emission bandwidths. Here, we show that injecting less than 10 mW of monomode laser radiation into a blue multimode 500 mW high power laser diode is capable of slaving at least 50% of the power to the desired frequency. We verify the emission bandwidth reduction by saturation spectroscopy on a strontium gas cell and by direct beating of the slave with the master laser. We also demonstrate that the laser can efficiently be used within the Zeeman slower for optical cooling of a strontium atomic beam.

  7. Advanced Capacitors for High-Power Applications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — As the consumer and industrial requirements for compact, high-power-density, electrical power systems grow substantially over the next decade; there will be a...

  8. Reviews of a Diode-Pumped Alkali Laser (DPAL): a potential high powered light source

    Science.gov (United States)

    Cai, He; Wang, You; Han, Juhong; An, Guofei; Zhang, Wei; Xue, Liangping; Wang, Hongyuan; Zhou, Jie; Gao, Ming; Jiang, Zhigang

    2015-03-01

    Diode pumped alkali vapor lasers (DPALs) were first developed by in W. F. Krupke at the beginning of the 21th century. In the recent years, DPALs have been rapidly developed because of their high Stokes efficiency, good beam quality, compact size and near-infrared emission wavelengths. The Stokes efficiency of a DPAL can achieve a miraculous level as high as 95.3% for cesium (Cs), 98.1% for rubidium (Rb), and 99.6% for potassium (K), respectively. The thermal effect of a DPAL is theoretically smaller than that of a normal diode-pumped solid-state laser (DPSSL). Additionally, generated heat of a DPAL can be removed by circulating the gases inside a sealed system. Therefore, the thermal management would be relatively simple for realization of a high-powered DPAL. In the meantime, DPALs combine the advantages of both DPSSLs and normal gas lasers but evade the disadvantages of them. Generally, the collisionally broadened cross sections of both the D1 and the D2 lines for a DPAL are much larger than those for the most conventional solid-state, fiber and gas lasers. Thus, DPALs provide an outstanding potentiality for realization of high-powered laser systems. It has been shown that a DPAL is now becoming one of the most promising candidates for simultaneously achieving good beam quality and high output power. With a lot of marvelous merits, a DPAL becomes one of the most hopeful high-powered laser sources of next generation.

  9. High-Power Diode Laser-Treated 13Cr4Ni Stainless Steel for Hydro Turbines

    Science.gov (United States)

    Mann, B. S.

    2014-06-01

    The cast martensitic chromium nickel stainless steels such as 13Cr4Ni, 16Cr5Ni, and 17Cr4Ni PH have found wide application in hydro turbines. These steels have adequate corrosion resistance with good mechanical properties because of chromium content of more than 12%. The 13Cr4Ni stainless steel is most widely used among these steels; however, lacks silt, cavitation, and water impingement erosion resistances (SER, CER, and WIER). This article deals with characterizing 13Cr4Ni stainless steel for silt, cavitation, and water impingement erosion; and studying its improved SER, CER, and WIER behavior after high-power diode laser (HPDL) surface treatment. The WIER and CER have improved significantly after laser treatment, whereas there is a marginal improvement in SER. The main reason for improved WIER and CER is due to its increased surface hardness and formation of fine-grained microstructure after HPDL surface treatment. CER and WIER of HPDL-treated 13Cr4Ni stainless steel samples have been evaluated as per ASTM G32-2003 and ASTM G73-1978, respectively; and these were correlated with microstructure and mechanical properties such as ultimate tensile strength, modified ultimate resilience, and microhardness. The erosion damage mechanism, compared on the basis of scanning electron micrographs and mechanical properties, is discussed and reported in this article.

  10. Cost-effective optoacoustic system based on the combination of high-power diode lasers

    Science.gov (United States)

    Sánchez, Miguel; Rodríguez, Sergio; Gawali, Sandeep B.; Leggio, Luca; Gallego, Daniel C.; Lamela, Horacio

    2017-03-01

    One of the main issues of the advances in optoacoustic (OA) applications is to reduce the high costs and the big sizes of solid state lasers. High-power diode lasers (HPDLs) have been demonstrated to be a valid alternative reducing enormously the expenses, besides other advantages such as smaller sizes and higher modulation frequencies. However, in some cases it is possible to furtherly reduce their costs. We present a cost-effective OA system based on the combination of several 905-nm HPDLs with direct coupling into a fiber bundle. These HPDLs have an internal pulse driver, based on an n-channel Mosfet and two charging capacitors, which needs an external Mosfet driver circuit and a voltage supply in order to improve the optical pulse shape and energy. We compare the performances and the prices of this OA system with another similar HPDL-based OA system built with commercial elements. Results indicate good OA signal generation ( 15.6 mVpp) with pulse energy of 12.3 μJ and, especially, a cost reduction by a factor of 15 if compared to the other HPDL-based system.

  11. Genetic algorithm based optimization of pulse profile for MOPA based high power fiber lasers

    Science.gov (United States)

    Zhang, Jiawei; Tang, Ming; Shi, Jun; Fu, Songnian; Li, Lihua; Liu, Ying; Cheng, Xueping; Liu, Jian; Shum, Ping

    2015-03-01

    Although the Master Oscillator Power-Amplifier (MOPA) based fiber laser has received much attention for laser marking process due to its large tunabilty of pulse duration (from 10ns to 1ms), repetition rate (100Hz to 500kHz), high peak power and extraordinary heat dissipating capability, the output pulse deformation due to the saturation effect of fiber amplifier is detrimental for many applications. We proposed and demonstrated that, by utilizing Genetic algorithm (GA) based optimization technique, the input pulse profile from the master oscillator (current-driven laser diode) could be conveniently optimized to achieve targeted output pulse shape according to real parameters' constraints. In this work, an Yb-doped high power fiber amplifier is considered and a 200ns square shaped pulse profile is the optimization target. Since the input pulse with longer leading edge and shorter trailing edge can compensate the saturation effect, linear, quadratic and cubic polynomial functions are used to describe the input pulse with limited number of unknowns(<5). Coefficients of the polynomial functions are the optimization objects. With reasonable cost and hardware limitations, the cubic input pulse with 4 coefficients is found to be the best as the output amplified pulse can achieve excellent flatness within the square shape. Considering the bandwidth constraint of practical electronics, we examined high-frequency component cut-off effect of input pulses and found that the optimized cubic input pulses with 300MHz bandwidth is still quite acceptable to satisfy the requirement for the amplified output pulse and it is feasible to establish such a pulse generator in real applications.

  12. 2.1 μm high-power laser diode beam combining(Conference Presentation)

    Science.gov (United States)

    Berrou, Antoine P. C.; Elder, Ian F.; Lamb, Robert A.; Esser, M. J. Daniel

    2016-10-01

    Laser power and brightness scaling, in "eye safe" atmospheric transmission windows, is driving laser system research and development. High power lasers with good beam quality, at wavelength around 2.1 µm, are necessary for optical countermeasure applications. For such applications, focusing on efficiency and compactness of the system is mandatory. In order to cope with these requirements, one must consider the use of laser diodes which emit directly in the desired spectral region. The challenge for these diodes is to maintain a good beam quality factor as the output power increases. 2 µm diodes with excellent beam quality in both axes are available with output powers of 100 mW. Therefore, in order to reach multi-watt of average output power, broad-area single emitters and beam combining becomes relevant. Different solutions have been implemented in the 1.9 to 2 µm wavelength range, one of which is to stack multiple emitter bars reaching more than one hundred watt, while another is a fibre coupled diode module. The beam propagation factor of these systems is too high for long atmospheric propagation applications. Here we describe preliminary results on non-coherent beam combining of 2.1 µm high power Fabry-Perot GaSb laser diodes supplied by Brolis Semiconductors Ltd. First we evaluated single mode diodes (143 mW) with good beam quality (M2 beam consisted of two symmetric lobes with a total full width at half maximum (FWHM) divergence angle of 25 degrees, corresponding to a calculated beam quality factor of M2 = 25. The fast axis divergence was specified to be 44 degrees, with an expected beam quality factor close to the diffraction limit, which informed our selection of collimation lenses used in the experiment. We evaluated two broadband (1.8 - 3 µm) AR coated Geltech aspheric lenses with focal lengths of 1.87 mm and 4 mm, with numerical apertures of 0.85 and 0.56, respectively, as an initial collimation lens, followed by an additional cylindrical lens of

  13. Large aperture N31 neodymium phosphate laser glass for use in a high power laser facility

    Institute of Scientific and Technical Information of China (English)

    Lili; Hu; Shubin; Chen; Jingping; Tang; Biao; Wang; Tao; Meng; Wei; Chen; Lei; Wen; Junjiang; Hu; Shunguang; Li; Yongchun; Xu; Yasi; Jiang; Junzhou; Zhang; Zhonghong; Jiang

    2014-01-01

    Large aperture Nd:phosphate laser glass is a key optical element for an inertial confinement fusion(ICF) facility. N31,one type of neodymium doped phosphate glasses, was developed for high peak power laser facility applications in China. The composition and main properties of N31 glass are given, together with those of LHG-8, LG-770, and KGSS-0180 Nd:phosphate laser glasses, from Hoya and Schott, and from Russia. The technologies of pot melting, continuous melting, and edge cladding of large size N31 phosphate laser glass are briefly described. The small signal gain profiles of N31 glass slabs from both pot melting and continuous melting at various values of the pumping energy of the xenon lamp are presented. N31 glass is characterized by a stimulated emission cross section of 3.8 × 10-20cm2 at 1053 nm,an absorption coefficient of 0.10–0.15% cm-1at laser wavelength, small residual stress around the interface between the cladding glass and the laser glass, optical homogeneity of ~2 × 10-6in a 400 mm aperture, and laser damage threshold larger than 42 J/cm2 for a 3 ns pulse width at 1064 nm wavelength.

  14. High-power single-mode vertical-cavity surface-emitting lasers

    Science.gov (United States)

    Samal, Nigamananda

    High-power single-mode vertical-cavity surface-emitting lasers (VCSEL) have a great potential to replace the distributed feedback (DFB) and Fabry-Perot (FP) edge emitting lasers that are currently used in optical communication. VCSELs also have tremendous potential in many niche applications such as "optical read and write," laser printing, bar code scanning and sensing. Despite many of their inherent advantages over its rivals, VCSELs still suffer from some outstanding issues. Most prominent are "limited power" and "multi-mode behavior" at higher injection. This work aims at a few solutions for these fundamental issues. Using strain-compensated GaAsSb as an active material and a standard single-aperture design, 1.3 mum VCSELs are demonstrated and characterized. These devices face basic issues such as "limited output power" and "multi-mode behavior." These VCSELs achieved room temperature CW operation with power outputs from 50--200 muW for wavelengths ranging from 1245 to 1290 nm. To resolve the issue of limited power, several on-wafer thermal-management schemes are proposed. One of the schemes is pursued in this work. To resolve the issue of multi-mode behavior, a novel device design using asymmetric double oxide-apertures is proposed, theoretically modeled, and implemented in this work. The optical mode behavior of this novel design is compared with a traditional single-aperture design using fabricated devices and theoretical modeling. A clear trend of spectral purity in the modal behavior of the devices, under both continuous wave (CW) and pulsed conditions, is demonstrated and is in good agreement with theoretical predictions. One of the novel designs tested on an InGaAs VCSEL has shown a multi-mode power more than 23 mW with maximum wall plug efficiency of 32%, threshold current of 2.5 mA, threshold voltage of 1.2 V, and a slope efficiency of 0.83 W/A. The best design demonstrated a room temperature CW single-mode output power of more than 7 mW with a side

  15. The impact of external optical feedback on the degradation behavior of high-power diode lasers

    DEFF Research Database (Denmark)

    Hempel, Martin; Chi, Mingjun; Petersen, Paul Michael;

    2013-01-01

    The impact of external feedback on high-power diode laser degradation is studied. For this purpose early stages of gradual degradation are prepared by accelerated aging of 808-nm-emitting AlGaAs-based devices. While the quantum well that actually experiences the highest total optical load remains...... unaffected, severe impact is observed to the cladding layers and the waveguide. Consequently hardening of diode lasers for operation under external optical feedback must necessarily involve claddings and waveguide, into which the quantum well is embedded.......The impact of external feedback on high-power diode laser degradation is studied. For this purpose early stages of gradual degradation are prepared by accelerated aging of 808-nm-emitting AlGaAs-based devices. While the quantum well that actually experiences the highest total optical load remains...

  16. Perspectives for neutron and gamma spectroscopy in high power laser driven experiments at ELI-NP

    Science.gov (United States)

    Negoita, F.; Gugiu, M.; Petrascu, H.; Petrone, C.; Pietreanu, D.; Fuchs, J.; Chen, S.; Higginson, D.; Vassura, L.; Hannachi, F.; Tarisien, M.; Versteegen, M.; Antici, P.; Balabanski, D.; Balascuta, S.; Cernaianu, M.; Dancus, I.; Gales, S.; Neagu, L.; Petcu, C.; Risca, M.; Toma, M.; Turcu, E.; Ursescu, D.

    2015-02-01

    The measurement of energy spectra of neutrons and gamma rays emitted by nuclei, together with charge particles spectroscopy, are the main tools for understanding nuclear phenomena occurring also in high power laser driven experiments. However, the large number of particles emitted in a very short time, in particular the strong X-rays flash produced in laser-target interaction, impose adaptation of technique currently used in nuclear physics experiment at accelerator based facilities. These aspects are discussed (Section 1) in the context of proposed studies at high power laser system of ELI-NP. Preliminary results from two experiments performed at Titan (LLNL) and ELFIE (LULI) facilities using plastic scintillators for neutron detection (Section 2) and LaBr3(Ce) scintillators for gamma detection (Section 3) are presented demonstrating the capabilities and the limitations of the employed methods. Possible improvements of these spectroscopic methods and their proposed implementation at ELI-NP will be discussed as well in the last section.

  17. High-power narrow-vertical-divergence photonic band crystal laser diodes with optimized epitaxial structure

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Lei; Qu, Hongwei; Liu, Yun; Zhang, Yejin; Zheng, Wanhua, E-mail: whzheng@red.semi.ac.cn [State Key Laboratory on Integrated Optoelectronics, Institute of Semiconductors, CAS, Beijing 100083 (China); Laboratory of Solid State Optoelectronics Information Technology, Institute of Semiconductors, CAS, Beijing 100083 (China); Wang, Yufei; Qi, Aiyi [Laboratory of Solid State Optoelectronics Information Technology, Institute of Semiconductors, CAS, Beijing 100083 (China)

    2014-12-08

    900 nm longitudinal photonic band crystal (PBC) laser diodes with optimized epitaxial structure are fabricated. With a same calculated fundamental-mode divergence, stronger mode discrimination is achieved by a quasi-periodic index modulation in the PBC waveguide than a periodic one. Experiments show that the introduction of over 5.5 μm-thick PBC waveguide contributes to only 10% increment of the internal loss for the laser diodes. For broad area PBC lasers, output powers of 5.75 W under continuous wave test and over 10 W under quasi-continuous wave test are reported. The vertical divergence angles are 10.5° at full width at half maximum and 21.3° with 95% power content, in conformity with the simulated angles. Such device shows a prospect for high-power narrow-vertical-divergence laser emission from single diode laser and laser bar.

  18. Efficient pump beam shaping for high-power thin-disk laser systems.

    Science.gov (United States)

    Pereira, Rui; Weichelt, Birgit; Liang, Dawei; Morais, Paulo J; Gouveia, Helena; Abdou-Ahmed, Marwan; Voss, Andreas; Graf, Thomas

    2010-09-20

    We report a beam-shaping technique whereby the output power from a high-power laser-diode stack is efficiently coupled, reconfigured, and transmitted to a thin-disk laser by means of a compact optical fiber bundle. By using this technique, the power density is increased by a factor of 2 when compared to direct coupling with a octagonal fused silica rod while the numerical aperture is kept constant. Transmission efficiency of 80% was measured for the beam shaper without antireflection coating. The top-hat distribution is numerically calculated at the thin-disk laser crystal.

  19. Quasi-passive heat sink for high-power laser diodes

    Science.gov (United States)

    Vetrovec, John

    2009-02-01

    We report on a novel heat sink for high-power laser diodes offering unparalleled capacity in high-heat flux handling and temperature control. The heat sink uses a liquid coolant flowing at high speed in a miniature closed and sealed loop. Diode waste heat is received at high flux and transferred to environment, coolant fluid, heat pipe, or structure at a reduced flux. When pumping solid-state or alkali vapor lasers, diode wavelength can be electronically tuned to the absorption features of the laser gain medium. This paper presents the heat sink physics, engineering design, performance modeling, and configurations.

  20. Progress in the development of active heat sink for high-power laser diodes

    Science.gov (United States)

    Vetrovec, John; Feeler, Ryan; Bonham, Steve

    2010-02-01

    We report on the development of a novel active heat sink for high-power laser diodes offering unparalleled capacity in high-heat flux handling and temperature control. The heat sink receives diode waste heat at high flux and transfers it at reduced flux to environment, coolant fluid, heat pipe, or structure. Thermal conductance of the heat sink is electronically adjustable, allowing for precise control of diode temperature and the output light wavelength. When pumping solid-state lasers, diode wavelength can be precisely tuned to the absorption features of the laser gain medium. This paper presents the AHS concept, scaling laws, model predictions, and data from initial testing.

  1. Widely Tunable High-Power Tapered Diode Laser at 1060 nm

    DEFF Research Database (Denmark)

    Jensen, Ole Bjarlin; Sumpf, Bernd; Erbert, Götz;

    2011-01-01

    We report a large tuning range from 1018 to 1093 nm from a InGaAs single quantum-well 1060-nm external cavity tapered diode laser. More than 2.5-W output power has been achieved. The tuning range is to our knowledge the widest obtained from a high-power InGaAs single quantum-well tapered laser...... operating around 1060 nm. The light emitted by the laser has a nearly diffraction limited beam quality and a narrow linewidth of less than 6 pm everywhere in the tuning range....

  2. Study of Dynamic Features of Surface Plasma in High-Power Disk Laser Welding

    Institute of Scientific and Technical Information of China (English)

    王腾; 高向东; Katayatna SEIJI; 金小莉

    2012-01-01

    High-speed photography was used to obtain the dynamic changes in the surface plasma during a high-power disk laser welding process. A color space clustering algorithm to extract the edge information of the surface plasma region was developed in order to improve the accuracy of image processing. With a comparative analysis of the plasma features, i.e., area and height, and the characteristics of the welded seam, the relationship between the surface plasma and the stability of the laser welding process was characterized, which provides a basic understanding for the real-time monitoring of laser welding.

  3. High-Power Diode-Side-Pumped Intracavity-Frequency-Doubled Continuous Wave 532 nm Laser

    Institute of Scientific and Technical Information of China (English)

    ZHANG Yu-Ping; ZHANG Hui-Yun; ZHONG Kai; LI Xi-Fu; WANG Peng; YAO Jian-Quan

    2007-01-01

    @@ An efficient and high-power diode-side-pumped cw 532nm green laser based on a V-shaped cavity geometry, and capable of generating 22.7 W green radiation with optical conversion efficiency of 8.31%, has been demonstrated. The laser is operated with rms noise amplitude of less than 1% and with M2-parameter of about 6.45 at the top of the output power. This laser has the potential for scaling to much higher output power.

  4. Stabilized high-power laser system for the gravitational wave detector advanced LIGO.

    Science.gov (United States)

    Kwee, P; Bogan, C; Danzmann, K; Frede, M; Kim, H; King, P; Pöld, J; Puncken, O; Savage, R L; Seifert, F; Wessels, P; Winkelmann, L; Willke, B

    2012-05-07

    An ultra-stable, high-power cw Nd:YAG laser system, developed for the ground-based gravitational wave detector Advanced LIGO (Laser Interferometer Gravitational-Wave Observatory), was comprehensively characterized. Laser power, frequency, beam pointing and beam quality were simultaneously stabilized using different active and passive schemes. The output beam, the performance of the stabilization, and the cross-coupling between different stabilization feedback control loops were characterized and found to fulfill most design requirements. The employed stabilization schemes and the achieved performance are of relevance to many high-precision optical experiments.

  5. Compact piezoelectric stacked actuators for high power applications.

    Science.gov (United States)

    Yao, K; Uchino, K; Xu, Y; Dong, S; Lim, L C

    2000-01-01

    Small, hollow, multilayer actuators with a diameter of 3 mm were fabricated by the stacking method from piezoelectric hard lead zirconate titanate (PZT) ceramics. Langevin vibrators were also constructed with the hollow multilayer actuators. The performance capabilities of the actuator and Langevin vibrator samples were examined under high-power conditions. The high-power vibration level at a given sinusoidal drive voltage was significantly enhanced by using a multilayer structure under either a nonresonance or resonance condition. A maximum vibration velocity of 0.17 m/sec was obtained for the 9-layer actuator sample under nonresonance conditions. The vibration velocity was further improved with the Langevin vibrator driven at the resonance frequency. The temperature rise due to heat generation under high-power conditions was the immediate limitation on the maximum accessible vibration velocity for the stacked actuators.

  6. Design of High Power Density Amplifiers: Application to Ka Band

    Science.gov (United States)

    Passi, Davide; Leggieri, Alberto; Di Paolo, Franco; Bartocci, Marco; Tafuto, Antonio

    2017-06-01

    Recent developments in the design of high-power-high-frequency amplifiers are assessed in this paper by the analysis and measurements of a high power density amplifier operating in the Ka Band. Design procedure is presented and a technical investigation is reported. The proposed device has shown over 23% of useful frequency bandwidth. It is an ensemble of 16 monolithic solid state power amplifiers that employees mixed technologies as spatial and planar combiners. Test performed have given maximum delivered power of 47.2 dBm.

  7. Comparison of ALD and IBS Al2O3 films for high power lasers

    Science.gov (United States)

    Liu, Hao; Jensen, Lars; Becker, Jürgen; Wurz, Marc Christopher; Ma, Ping; Ristau, Detlev

    2016-12-01

    Atomic layer deposition (ALD) has been widely studied in Micro-electronics due to its self-terminating property. ALD also grows film coatings with precise thickness and nodular-free structure, which are desirable properties for high power coatings. The depositing process was studied to produce uniform, stable and economic Al2O3 single layers. The layer properties relevant to high power laser industry were studied and compared with IBS Al2O3 single layers. ALD Al2O3 showed a stable growth of 0.104 nm/cycle, band gap energy of 6.5 eV and tensile stress of about 480 MPa. It also showed a low absorption at wavelength 1064 nm within several ppm, and LIDT above 30 J/cm2. These properties are superior to the reference IBS Al2O3 single layers and indicate a high versatility of ALD Al2O3 for high power coatings.

  8. High Power Electro-Optic Modulator for Space-Based Applications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — ADVR, Inc. proposes the development of a fiber coupled, high power, electro-optically controlled, space qualified, phase modulator for the NASA Laser Interferometer...

  9. High-Power Laser Pulse Recirculation for Inverse Compton Scattering-Produced Gamma-Rays

    Energy Technology Data Exchange (ETDEWEB)

    Jovanovic, I; Shverdin, M; Gibson, D; Brown, C

    2007-04-17

    Inverse Compton scattering of high-power laser pulses on relativistic electron bunches represents an attractive method for high-brightness, quasi-monoenergetic {gamma}-ray production. The efficiency of {gamma}-ray generation via inverse Compton scattering is severely constrained by the small Thomson scattering cross section. Furthermore, repetition rates of high-energy short-pulse lasers are poorly matched with those available from electron accelerators, resulting in low repetition rates for generated {gamma}-rays. Laser recirculation has been proposed as a method to address those limitations, but has been limited to only small pulse energies and peak powers. Here we propose and experimentally demonstrate an alternative method for laser pulse recirculation that is uniquely capable of recirculating short pulses with energies exceeding 1 J. Inverse Compton scattering of recirculated Joule-level laser pulses has a potential to produce unprecedented peak and average {gamma}-ray brightness in the next generation of sources.

  10. Heat transfer performance of water jet cooled mirror and its application in high power chemical lasers%射流式水冷镜换热性能及在高能化学激光器中的应用

    Institute of Scientific and Technical Information of China (English)

    李斌; 李兰; 焦路光; 刘亮; 周琼; 袁圣付; 刘文广

    2012-01-01

    加工了射流式水冷铜镜模型,采用红外热像仪测量了冷却过程中镜面温度分布云图,证明了射流式水冷镜冷却的均匀性.采用热电偶较精确地测量了铜镜冷却过程中镜面温度的变化,实验结果与数值模拟吻合较好,验证了射流式水冷镜数值模型的可靠性.结合高能化学激光器中水冷镜实际情况,对直线沟槽型水冷镜和射流式水冷镜的形变特性进行了分析.计算结果表明,高能化学激光器水冷镜必须承压加工才能使用,射流式水冷镜可以很好地应用于高能化学激光器.此外,进一步分析了冷却孔直径和数量这两个参数对大口径射流式水冷镜形变的影响,结果表明:在孔数一定的情况下,采用更大口径的冷却孔,镜面冷却速度快、镜面最大温度低,可以获得更小的镜面形变;采用更多的冷却孔可以获得更好的冷却效果.%The test model of water jet cooled copper mirror was made and temperature measurement of the mirror was carried out. The temperature uniformity of the water jet cooled copper mirror was proved by the measurements of infrared camera and experimental results of thermocouples agree well with the results of numerical simulation, which verified the reliability of the numerical model. The deformation characteristics of the water jet cooled mirror and the linear-channel water cooled mirror were analyzed in the scenario of high power chemical lasers. The results show that the water jet cooled mirror can be well used in high power chemical lasers and the mirror must be processed under certain pressure. In addition, the diameter and number of cooling holes were further analyzed to explore their effects on the deformation of water jet cooled mirror in high power chemical lasers. More holes with larger diameter lead to better cooling effects.

  11. Experimental studies for improvement of thermal effects in a high-power fiber-coupled diode laser module operating at 808 nm

    Science.gov (United States)

    El-Sherif, Ashraf F.; Hussein, Khalid; Hassan, Mahmoud F.; Talat, Mahmoud M.

    2012-03-01

    High power diode laser module operating at 808 nm is required for different applications, such as developing an efficient high power Nd3+-doped solid state laser and Tm3+ -doped silica fiber laser, industrial, medical and military applications. Optical and thermal images characterization for a fiber-coupled high power diode laser module is presented experimentally for 6.6 Watt output optical power .An external temperature controller system was designed, which stabilizes the central wavelength at 808 nm at 25°C over a wide range of diode laser driving current from 1A to 6 A. without this cooling system, the wavelength changes by 0.35nm/°C for temperature changes from 20°C to 40°C at the same range of the driving current. In this paper we have present a methodology for temperature reduction of a 808 nm high power diode laser module, based on dynamically thermal control, which is known as dynamic thermal management. Stabilization of the output wavelength has been done by using proportional speed control (PSC) of a CPU cooling fan with certain scheme of straight fins heat sink. Two electronic circuits based on pulse width modulation (PWM) in microcontroller and comparators IC have been used. This technique can be considered as an effective mechanism for reducing temperature and power dissipation to make stabilization of the diode laser output wavelength by preventing heat accumulation from the thermo electric cooling (TEC) inside the diode laser module confirmed by thermal images.

  12. Apply high-power fiber laser in oil/gas wells drilling

    Science.gov (United States)

    Jiang, Houman; Guo, Shaofeng; Chen, Minsun; Wang, Wenliang

    2015-05-01

    The concept of using lasers to drill through rock has been discussed in the oil and gas industries since the development of the high-power laser. To evaluate the possibility of fielding a laser drilling system, two laser-related problems have to be investigated. The first is the irradiation effects of laser upon rocks; the second is the effects in laser transmission from the source to the rock deep in the well. This transmission includes two stages: the first stage is the transmission inside a fiber, which is packaged in a cable and has about the same length with the well depth; the second stage refers to the transmission process when the laser leaves the fiber and some transforming optics and transmits to the rock surface, during which the well conditions may impose tough restrictions. In this paper, experiment results of laser irradiation upon siliceous sandstone and granite are reported, and the fiber transmission loss is simulated, considering the main absorbing or scattering mechanisms inside fiber. And the laser transmission from the fiber end to the rock surface, in my view, may impose great challenge on the laser drilling technology.

  13. High-power Laser Welding of Thick Steel-aluminum Dissimilar Joints

    Science.gov (United States)

    Lahdo, Rabi; Springer, André; Pfeifer, Ronny; Kaierle, Stefan; Overmeyer, Ludger

    According to the Intergovernmental Panel on Climate Change (IPCC), a worldwide reduction of CO2-emissions is indispensable to avoid global warming. Besides the automotive sector, lightweight construction is also of high interest for the maritime industry in order to minimize CO2-emissions. Using aluminum, the weight of ships can be reduced, ensuring lower fuel consumption. Therefore, hybrid joints of steel and aluminum are of great interest to the maritime industry. In order to provide an efficient lap joining process, high-power laser welding of thick steel plates (S355, t = 5 mm) and aluminum plates (EN AW-6082, t = 8 mm) is investigated. As the weld seam quality greatly depends on the amount of intermetallic phases within the joint, optimized process parameters and control are crucial. Using high-power laser welding, a tensile strength of 10 kN was achieved. Based on metallographic analysis, hardness tests, and tensile tests the potential of this joining method is presented.

  14. High power double-scale pulses from a gain-guided double-clad fiber laser

    Science.gov (United States)

    Zhang, Haitao; Gao, Gan; Li, Qinghua; Gong, Mali

    2017-03-01

    Generation of high power double-scale pulses from a gain-guided double-clad fiber laser is experimentally demonstrated. By employing the Yb-doped 10/130 double-clad fiber as the gain medium, the laser realizes an output power of 5.1 W and pulse energy of 0.175 µJ at repetition rate of 29.14 MHz. To the best of our knowledge, this average output power is the highest among the reported double-scale pulse oscillators. The autocorrelation trace of pulses contains the short (98 fs) and long (29.5 ps) components, and the spectral bandwidth of the pulse is 27.3 nm. Such double-scale pulses are well suited for seeding the high power MOPA (master oscillator power amplifier) systems, nonlinear frequency conversion and optical coherence tomography.

  15. High-power near-diffraction-limited solid-state amplified spontaneous emission laser devices.

    Science.gov (United States)

    Smith, G; Shardlow, P C; Damzen, M J

    2007-07-01

    We present investigations into high-power scaling of solid-state amplified spontaneous emission (ASE) laser sources by use of two high-gain (~10(4)) Nd:YVO(4) bounce amplifiers. The sources deliver high power with a high-quality spatial output, but unlike a laser they have a high misalignment tolerance and do not require a precisely aligned cavity. In one system with two amplifiers, we demonstrate an ASE source with 24.5W of output power with good spatial quality, M(2)vertical. In a more sophisticated setup, the two amplifiers are arranged in a loop configuration producing 30W of ASE output with near-diffraction-limited spatial quality, with M(2)vertical, at an ~38% optical-to-optical conversion efficiency.

  16. Review of self-focusing of high power lasers in large-mode-area optical fibers

    Energy Technology Data Exchange (ETDEWEB)

    Zhao Chujun; Li Ying; Lei Dajun; Yang Hua; Wen Shuangchun; Fan Dianyuan; Wen Jianguo, E-mail: scwen@vip.sina.com [Key Laboratory for Micro/Nano Optoelectronic Devices of Ministry of Education, School of Computer and Communication, Hunan University, Changsha 410082 (China)

    2011-02-01

    The main progress about the self-focusing of high power lasers in large-mode-area optical fiber has been reviewed. The theoretical models including the self-focusing effects have been discussed. Some different views on the whole beam self focusing and small scale self-focusing effects in optical fiber have been introduced. Moreover, the possible methods exceeding the bulk-media self-focusing threshold have been discussed and explored.

  17. Volume structuring of high power LED encapsulates by femtosecond laser direct writing

    Energy Technology Data Exchange (ETDEWEB)

    Kuna, L.; Sommer, C.; Zinterl, E.; Krenn, J.R.; Wenzl, F.P. [Joanneum Research Forschungsges. mbH, Institute of Nanostructured Materials and Photonics, Weiz (Austria); Pachler, P.; Hartmann, P.; Tasch, S. [TridonicAtco Optoelectronics GmbH, Jennersdorf (Austria); Leising, G. [Graz University of Technology, Institute of Solid State Physics, Graz (Austria)

    2008-11-15

    We report on the micro-fabrication of diffractive optical elements (DOEs) such as 1D, 2D and concentric grating structures inside the volume of thin silicone films by femtosecond laser direct writing. In addition, we show that such structures can also be integrated into silicone films that act as encapsulation layers of high power light-emitting diodes. The latter strategy opens new possibilities to homogenize and to control the light emitted from such devices. (orig.)

  18. Study on the beam shaping of high-power laser diode bars

    Institute of Scientific and Technical Information of China (English)

    Wei Huang(黄伟); Xiaodong Zeng(曾晓东); Yuying An(安毓英)

    2003-01-01

    Based on the Collins form, the intensity distribution of the resulting beam is derived when Gaussian beamsof a high-power laser diode bar pass through a paraxial optical system. Then flattop beam profiles areobtained by a concave cylindrical lens, and the propagation properties are discussed in detail, such as thepeak-intensity axis inclined at an angle γi. In addition, an expression to calculate beam angular width ispresented.

  19. Neutralization of improvised explosive devices by high-power lasers: research results from the FP7 project ENCOUNTER

    Science.gov (United States)

    Osterholz, J.; Lueck, M.; Lexow, B.; Wickert, M.

    2016-10-01

    The development of reliable techniques for the safe neutralization of improvised explosive devices (IEDs) is an active field of research. Recently, innovative approaches for the neutralization of IEDs were developed and tested within the FP7 project ENCOUNTER ("Explosive Neutralisation and Mitigation Countermeasures for IEDs in Urban/Civil Environment") and were compared to existing, established technologies. Here, the ENCOUNTER project is presented with a special focus on the neutralization of IEDs by high-power lasers. The working principle of the application of high-power lasers for the neutralization of explosive devices is based on thermal effects. Heating of the IEDs main charge may occur either by direct irradiation of the explosive material or by heat transfer through the main charge's confinement. The aim of the application of the laser is to achieve a low order burning reaction of the explosive charge and thus a controlled neutralization of the IED. Since laser beams allow for the directed transport of energy, this technique can be applied over long stand-off distances and has thus potential for an increase of the safety of clearing forces and population in the case of terroristic attacks in a civilian environment. Within the ENCOUNTER project, a laboratory environment has been set up which allows for the irradiation of IEDs with a laser power of up to 10 kW. Experiments have been carried out on a broad spectrum of different types of IEDs. The processes during neutralization were studied in detail with high-speed diagnostics. On the basis of these experimental data, the safety and the reliability of the application of the laser was analyzed, and recommendations to end users were given. In addition to the results of the ENCOUNTER project, approaches for the numerical simulation of the neutralization of IEDs are discussed.

  20. Thermal properties of high-power diode lasers investigated by means of high resolution thermography

    Energy Technology Data Exchange (ETDEWEB)

    Kozlowska, Anna, E-mail: Anna.Kozlowska@itme.edu.pl [Institute of Electronic Materials Technology, 133 Wolczynska St., 01-919 Warsaw (Poland); Malag, Andrzej; Dabrowska, Elzbieta; Teodorczyk, Marian [Institute of Electronic Materials Technology, 133 Wolczynska St., 01-919 Warsaw (Poland)

    2012-09-01

    In the present work, thermal effects in high-power diode lasers are investigated by means of high resolution thermography. Thermal properties of the devices emitting in the 650 nm and 808 nm wavelength ranges are compared. The different versions of the heterostructure design are analyzed. The results show a lowering of active region temperature for diode lasers with asymmetric heterostructure scheme with reduced quantum well distance from the heterostructure surface (and the heat sink). Optimization of technological processes allowed for the improvement of the device performance, e.g. reduction of solder non-uniformities and local defect sites at the mirrors which was visualized by the thermography.

  1. High-Power γ-Ray Flash Generation in Ultraintense Laser-Plasma Interactions

    Science.gov (United States)

    Nakamura, Tatsufumi; Koga, James K.; Esirkepov, Timur Zh.; Kando, Masaki; Korn, Georg; Bulanov, Sergei V.

    2012-05-01

    When high-intensity laser interaction with matter enters the regime of dominated radiation reaction, the radiation losses open the way for producing short pulse high-power γ-ray flashes. The γ-ray pulse duration and divergence are determined by the laser pulse amplitude and by the plasma target density scale length. On the basis of theoretical analysis and particle-in-cell simulations with the radiation friction force incorporated, optimal conditions for generating a γ-ray flash with a tailored overcritical density target are found.

  2. Evidence of thermal effects in high power Er3+-Yb3+ fiber laser

    CERN Document Server

    Canat, Guillaume; Jaouen, Yves; Dussardier, Bernard; 10.1364/OL.30.003030

    2011-01-01

    We analyse the influence of heat generation by non radiative transitions in high power 1.55$\\mu$m double cladding Erbium-Ytterbium fiber laser. At strong pumping rates, 1$\\mu$m lasing can start due to parasitic reflections. We present a model including heat generation and its effect on the Stark level population using the MacCumber relation. Heat generation plays then a significant role and improves the 1.5$\\mu$m laser efficiency by increasing the 1$\\mu$m threshold.

  3. Dual Wavelength High Power Double-Clad Ytterbium-Doped Fiber Laser

    Science.gov (United States)

    Moghaddam, M. R. A.; Harun, S. W.; Shahi, S.; Ahmad, H.

    A dual wavelength high power double-clad erbium/ytterbium-doped fiber laser with a narrowest spacing of 0.4 nm and a M2 value of close to unity is presented in the region of 1565 nm. This result can be realized with a significant improvement of the mode competition problem using a loop mirror as a comb filter. The wavelength region can also be varied using polarization controllers in the loop mirror. This dual-wavelength fiber laser with side mode suppression ratio (SMSR) of 40 dB is quite stable, and the output power variance is as low as 0.46 dB.

  4. Interaction of high-power laser radiation with low-density polymer aerogels

    Science.gov (United States)

    Kaur, Ch; Chaurasia, Sh; Borisenko, N. G.; Orekhov, A. S.; Leshma, P.; Pimenov, V. G.; Sklizkov, G. V.; Akunets, A. A.; Deo, M. N.

    2017-06-01

    The interaction of high-power subnanosecond laser pulses with low-density targets of cellulose triacetate polymer is considered. An Nd-glass laser setup provides a focal spot intensity of over 1014 W cm-2. An investigation is made of absorption of laser radiation, laser-to-X-ray energy conversion, spectra of ions emitted from the plasma, transmission of laser radiation through the target and plasma, as well as volume heating of the target material. It is experimentally determined that the laser energy conversion efficiency to X-rays with photon energies of a few kiloelectronvolts decreases with increasing target material density. With the use of targets of density 10 mg cm-3 this efficiency is two times lower in comparison to 2 mg cm-3 density targets. The duration and amplitude of laser pulses transmitted through the target decreases with increasing column target density (the product of target material density and its thickness). The spectra of ions emitted from low-density target plasmas are recorded using ion collectors positioned at different angles relative to the direction of laser beam propagation as well as a high-resolution Thomson mass spectrometer. The ion flux and ion energies are found to increase with increasing target material density. The peak of the ion energy spectrum is shifted towards higher energies with increasing laser radiation intensity.

  5. Three-dimensional welding and cutting using high-power CO2 or YAG laser

    Science.gov (United States)

    Zuo, Tiechuan; Chen, Jiming; Xiao, Rongshi; Bao, Yong

    2000-10-01

    In this paper, the theory of 3D laser welding and cutting was established firstly. Then the expert system for 3D laser processing and software of 3D laser processing CAD/CAM were developed, respectively. Under the guidance of these software, with high power CO2 laser, the 3D covers of a car have been cut and edge smoothed, which decrease the number of models and shorten the period of production. With adoption of this technology, the covers of extended Hong Qi cars and furthermore Da Hong Qi cars have been processed successfully, which will bring out the innovation of production design and the revolution of processing technology in manufacture industry.

  6. A compact ultranarrow high-power laser system for experiments with 578 nm ytterbium clock transition

    Energy Technology Data Exchange (ETDEWEB)

    Cappellini, G., E-mail: cappellini@lens.unifi.it [LENS European Laboratory for Nonlinear Spectroscopy, 50019 Sesto Fiorentino (Italy); Lombardi, P. [Department of Physics and Astronomy, University of Florence, 50019 Sesto Fiorentino (Italy); INO-CNR Istituto Nazionale di Ottica del CNR, Sezione di Sesto Fiorentino, 50019 Sesto Fiorentino (Italy); Mancini, M.; Pagano, G. [Department of Physics and Astronomy, University of Florence, 50019 Sesto Fiorentino (Italy); Pizzocaro, M. [INRIM Istituto Nazionale di Ricerca Metrologica, Torino 10135 (Italy); Fallani, L. [LENS European Laboratory for Nonlinear Spectroscopy, 50019 Sesto Fiorentino (Italy); Department of Physics and Astronomy, University of Florence, 50019 Sesto Fiorentino (Italy); Catani, J. [LENS European Laboratory for Nonlinear Spectroscopy, 50019 Sesto Fiorentino (Italy); INO-CNR Istituto Nazionale di Ottica del CNR, Sezione di Sesto Fiorentino, 50019 Sesto Fiorentino (Italy)

    2015-07-15

    In this paper, we present the realization of a compact, high-power laser system able to excite the ytterbium clock transition at 578 nm. Starting from an external-cavity laser based on a quantum dot chip at 1156 nm with an intra-cavity electro-optic modulator, we were able to obtain up to 60 mW of visible light at 578 nm via frequency doubling. The laser is locked with a 500 kHz bandwidth to an ultra-low-expansion glass cavity stabilized at its zero coefficient of thermal expansion temperature through an original thermal insulation and correction system. This laser allowed the observation of the clock transition in fermionic {sup 173}Y b with a <50 Hz linewidth over 5 min, limited only by a residual frequency drift of some 0.1 Hz/s.

  7. Transmission properties of all-silica fibres for high-power Nd:YAG lasers

    Science.gov (United States)

    Reng, N.; Beck, T.

    1993-04-01

    The transmission properties of two different types of all-silica fibres, step index and graded-index fibres, are investigated using a multimode high-power cw Nd:YAG rod laser. The reflections from the fibre surface back into the laser cavity affect the laser power and the beam parameters, waist diameter and divergence. A set-up for simultaneously measuring these values in front of and behind a fibre is presented. The maximum laser power transmitted by fibres is dependent upon the beam parameters, the fibre design and the surface conditions. An upper limit for the maximum divergence which can be coupled into a fibre with a certain numerical aperture without loss is given. The beam parameters behind the fibre, related to the input parameters, are presented.

  8. High-power and low-intensity noise laser at 1064  nm.

    Science.gov (United States)

    Guiraud, Germain; Traynor, Nicholas; Santarelli, Giorgio

    2016-09-01

    We have developed a single-frequency, narrow-linewidth (Δνlaser operating at 1064 nm with a high output power (50 W). The laser is based on an ytterbium-doped fiber master oscillator power amplifier architecture with an output beam at the diffraction limit. An output power of 50 W is obtained with two amplification stages using a 50 mW diode laser seeder. We have carefully studied the relative intensity noise at each amplification stage. The detrimental effect due to stimulated Brillouin scattering on residual amplitude noise has been observed on the high-power booster stage. After careful optimization, this laser exhibits low intensity noise with a RMS value equal to 0.012% (1 kHz/10 MHz) at 50 W.

  9. CVD Diamond Sink Application in High Power 3D MCMs

    Institute of Scientific and Technical Information of China (English)

    XIE Kuo-jun; JIANG Chang-shun; LI Cheng-yue

    2005-01-01

    As electronic packages become more compact, run at faster speeds and dissipate more heat, package designers need more effective thermal management materials. CVD diamond, because of its high thermal conductivity, low dielectric loss and its great mechanical strength, is an excellent material for three dimensional (3D) multichip modules (MCMs) in the next generation compact high speed computers and high power microwave components. In this paper, we have synthesized a large area freestanding diamond films and substrates, and polished diamond substrates, which make MCMs diamond film sink becomes a reality.

  10. High efficiency,high power 808nm laser array and stacked arrays optimized for elevated temperature operation

    Institute of Scientific and Technical Information of China (English)

    Crump P A; Wise D; Crum T R; DeVito M; Farmer J; Grimshaw M; Huang Z; Igl S A; Macomber S; Thiagarajan P

    2004-01-01

    Operation of 808-nm laser diode pumping at elevated temperature is crucial to many applications. Reliable operation at high power is limited by high thermal load and low catastrophic optical mirror damage (COMD) threshold at elevated temperature range. We demonstrated high efficiency and high power operation at elevated temperature with high COMD power. These results were achieved through device design optimization such as growth conditions, doping profile, and materials composition of the quantum-well and other layers. Electrical-to-optical efficiency as high as 62% was obtained through lowered threshold current, lowered series resistance and increased slope efficiency. The performance of single broad-area laser diodes scales to that of high power single bars on water-cooled copper micro-channel heatsinks or conductively-cooled CS heatsinks. No reduction in bar performance or significant spectral broadening is seen when these micro-channel coolers are assembled into 6-bar and 18-bar CW stacks for the highest power levels.

  11. High-power fiber laser cutting parameter optimization for nuclear decommissioning

    Energy Technology Data Exchange (ETDEWEB)

    Lopez, Ana Beatriz; Assuncao, Eurico; Quintino, Luisa [IDMEC, Instituto Superior Tecnico, Universidade de Lisboa, Lisboa (Portugal); Khan, Ali; Blackbun, Jonathan [TWI Ltd., Cambridge (United States)

    2017-06-15

    For more than 10 years, the laser process has been studied for dismantling work; however, relatively few research works have addressed the effect of high-power fiber laser cutting for thick sections. Since in the nuclear sector, a significant quantity of thick material is required to be cut, this study aims to improve the reliability of laser cutting for such work and indicates guidelines to optimize the cutting procedure, in particular, nozzle combinations (standoff distance and focus position), to minimize waste material. The results obtained show the performance levels that can be reached with 10 kW fiber lasers, using which it is possible to obtain narrower kerfs than those found in published results obtained with other lasers. Nonetheless, fiber lasers appear to show the same effects as those of CO{sub 2} and ND:YAG lasers. Thus, the main factor that affects the kerf width is the focal position, which means that minimum laser spot diameters are advised for smaller kerf widths.

  12. High-power fiber laser cutting parameter optimization for nuclear Decommissioning

    Directory of Open Access Journals (Sweden)

    Ana Beatriz Lopez

    2017-06-01

    Full Text Available For more than 10 years, the laser process has been studied for dismantling work; however, relatively few research works have addressed the effect of high-power fiber laser cutting for thick sections. Since in the nuclear sector, a significant quantity of thick material is required to be cut, this study aims to improve the reliability of laser cutting for such work and indicates guidelines to optimize the cutting procedure, in particular, nozzle combinations (standoff distance and focus position, to minimize waste material. The results obtained show the performance levels that can be reached with 10 kW fiber lasers, using which it is possible to obtain narrower kerfs than those found in published results obtained with other lasers. Nonetheless, fiber lasers appear to show the same effects as those of CO2 and ND:YAG lasers. Thus, the main factor that affects the kerf width is the focal position, which means that minimum laser spot diameters are advised for smaller kerf widths.

  13. High Power Combline Filter for Deep Space Applications

    Directory of Open Access Journals (Sweden)

    A. V. G. Subramanyam

    2014-01-01

    Full Text Available An S-band, compact, high power filter, for use in the Mars Orbiter Mission (MOM of Indian Space Research Organization (ISRO, has been designed and tested for multipaction. The telemetry, tracking, and commanding (TT&C transponder of MOM is required to handle continuous RF power of 200 W in the telemetry path besides simultaneously maintaining an isolation of greater than 145 dBc to its sensitive telecommand path. This is accomplished with the help of a complex diplexer, requiring high power, high rejection transmit path filter, and a low power receive path filter. To reduce the complexity in the multipaction-free design and testing, the transmit path filter of the diplexer is split into a low rejection filter integral to the diplexer and an external high rejection filter. This paper highlights the design and space qualification phases of this high rejection filter. Multipaction test results with 6 dB margin are also presented. Major concerns of this filter design are isolation, insertion loss, and multipaction. Mission performance of the on-board filter is normal.

  14. Highspeed laser welding of steel using a high-power single-mode continuous-wave fiber laser

    Science.gov (United States)

    Drechsel, J.; Loeschner, U.; Schwind, S.; Hartwig, L.; Schille, J.; Exner, H.; Huebner, P.; Eysert, A.

    2013-02-01

    Since a few years, high brilliance laser sources find their way into laser material processing. Laser micro processing by applying high brilliance laser radiation up to 3 kW of continuous wave laser power in combination with ultrafast beam deflection systems has been successfully demonstrated in 2008 for the first time. In the fields of laser welding, high brilliant laser radiation was mainly used for micro welding, but up to now the macro range is still insufficiently investigated. Hence, this study reports on detailed investigations of high speed laser welding of different steel grades, performed with a high power single mode fiber laser source. The laser beam was deflected relative to the sample by using both a fast galvanometer scanner system with f-theta focusing objective and a linear axis in combination with a welding optic, respectively. In the study, the mainly process influencing parameters such as laser power, welding speed, thickness of the metal sheets, angle of incidence and laser beam spot size were varied in a wide range. The weld seam quality was evaluated by structural analyses, static tensile tests and EDX measurements. Finally, the laser welding process has been optimized for different weld seam geometries, for example bead-on-plate welds and butt welds.

  15. Nanoscale coatings for erosion and corrosion protection of copper microchannel coolers for high powered laser diodes

    Science.gov (United States)

    Flannery, Matthew; Fan, Angie; Desai, Tapan G.

    2014-03-01

    High powered laser diodes are used in a wide variety of applications ranging from telecommunications to industrial applications. Copper microchannel coolers (MCCs) utilizing high velocity, de-ionized water coolant are used to maintain diode temperatures in the recommended range to produce stable optical power output and control output wavelength. However, aggressive erosion and corrosion attack from the coolant limits the lifetime of the cooler to only 6 months of operation. Currently, gold plating is the industry standard for corrosion and erosion protection in MCCs. However, this technique cannot perform a pin-hole free coating and furthermore cannot uniformly cover the complex geometries of current MCCs involving small diameter primary and secondary channels. Advanced Cooling Technologies, Inc., presents a corrosion and erosion resistant coating (ANCERTM) applied by a vapor phase deposition process for enhanced protection of MCCs. To optimize the coating formation and thickness, coated copper samples were tested in 0.125% NaCl solution and high purity de-ionized (DIW) flow loop. The effects of DIW flow rates and qualities on erosion and corrosion of the ANCERTM coated samples were evaluated in long-term erosion and corrosion testing. The robustness of the coating was also evaluated in thermal cycles between 30°C - 75°C. After 1000 hours flow testing and 30 thermal cycles, the ANCERTM coated copper MCCs showed a corrosion rate 100 times lower than the gold plated ones and furthermore were barely affected by flow rates or temperatures thus demonstrating superior corrosion and erosion protection and long term reliability.

  16. Highly reliable high-power AlGaAs/GaAs 808 nm diode laser bars

    Science.gov (United States)

    Hülsewede, R.; Schulze, H.; Sebastian, J.; Schröder, D.; Meusel, J.; Hennig, P.

    2007-02-01

    There are strong demands at the market to increase power and reliability for 808 nm diode laser bars. Responding to this JENOPTIK Diode Lab GmbH developed high performance 808 nm diode laser bars in the AlGaAs/GaAs material system with special emphasis to high power operation and long term stability. Optimization of the epitaxy structure and improvements in the diode laser bar design results in very high slope efficiency of >1.2 W/A, low threshold current and small beam divergence in slow axis direction. Including low serial resistance the overall wall plug efficiency is up to 65% for our 20%, 30% and 50% filling factor 10 mm diode laser bars. With the JENOPTIK Diode Lab cleaving and coating technique the maximum output power is 205 W in CW operation and 377 W in QCW operation (200 μs, 2% duty cycle) for bars with 50% filling factor. These bars mounted on micro channel cooled package are showing a very high reliability of >15.000 h. Mounted on conductive cooled package high power operation at 100 W is demonstrated for more than 5000h.

  17. Recent advancements in transparent ceramics and crystal fibers for high power lasers

    Science.gov (United States)

    Kim, W.; Baker, C.; Villalobos, G.; Florea, C.; Gibson, D.; Shaw, L. B.; Bowman, S.; Bayya, S.; Sadowski, B.; Hunt, M.; Askins, C.; Peele, J.; Aggarwal, I. D.; Sanghera, J. S.

    2013-05-01

    In this paper, we present our recent progress in the development of rare-earth (Yb3+ or Ho3+) doped Lu2O3 and Y2O3 sesquioxides for high power solid state lasers. We have fabricated high quality transparent ceramics using nano-powders synthesized by a co-precipitation method. This was accomplished by developments in high purity powder synthesis and low temperature scalable sintering technology developed at NRL. The optical, spectral and morphological properties as well as the lasing performance from our highly transparent ceramics are presented. In the second part of the paper, we discuss our recent research effort in developing cladded-single crystal fibers for high power single frequency fiber lasers has the potential to significantly exceed the capabilities of existing silica fiber based lasers. Single crystal fiber cores with diameters as small as 35μm have been drawn using high purity rare earth doped ceramic or single crystal feed rods by the Laser Heated Pedestal Growth (LHPG) process. Our recent results on the development of suitable claddings on the crystal fiber core are discussed.

  18. Multi-wavelength photoacoustic system based on high-power diode laser bars

    Science.gov (United States)

    Leggio, Luca; Wiśniowski, Bartosz; Gawali, Sandeep Babu; Rodríguez, Sergio; Sánchez, Miguel; Gallego, Daniel; Carpintero, Guillermo; Lamela, Horacio

    2017-03-01

    Multi-wavelength laser sources are necessary for a functional photoacoustic (PA) spectroscopy. The use of high-power diode lasers (HPDLs) has aroused great interest for their relatively low costs and small sizes if compared to solid state lasers. However, HPDLs are only available at few wavelengths and can deliver low optical energy (normally in the order of μJ), while diode laser bars (DLBs) offer more wavelengths in the market and can deliver more optical energy. We show the simulations of optical systems for beam coupling of single high-power DLBs operating at different wavelengths (i.e. 808 nm, 880 nm, 910 nm, 940 nm, and 980 nm) into 400-μm optical fibers. Then, in a separate design, the beams of the DLBs are combined in a compact system making use of dichroic mirrors and focusing lenses for beam coupling into a 400-μm optical fiber. The use of optical fibers with small core diameter (interior examination of the body.

  19. Power Density Distribution Simulation and Relevant Heat Effect Calculation of a High-power CO2 Laser with Low Order Modes

    Institute of Scientific and Technical Information of China (English)

    李俊昌; 马琨; 樊则宾

    2002-01-01

    The vertical excitation axial-flux kilowatt CO2 laser is an equipment widely used in the high-power laser heat treatment industrial applications. The experimental measurements indicate that the power density distribution of laser beam is generally of ring distribution with a sunken at the center, therefore the laser beam cannot be simply regarded as base mode Gaussian beam. In this paper, such laser beam is regarded as the non-interference superposition of TEM00 and TEM01 mode beams, the method to determine the simulation parameters is discussed, and the relevant heat effect calculation equation is deduced.

  20. Damage Resistant Optical Glasses for High Power Lasers: A Continuing Glass Science and Technology Challenge

    Energy Technology Data Exchange (ETDEWEB)

    Campbell, J H

    2002-08-28

    A major challenge in the development of optical glasses for high-power lasers is reducing or eliminating laser-induced damage to the interior (bulk) and the polished surface of the glass. Bulk laser damage in glass generally originates from inclusions. With the development of novel glass melting and forming processes it is now possible to make both fused silica and a suit of meta-phosphate laser glasses in large sizes ({approx}>0.5-lm diameter), free of inclusions and with high optical homogeneity ({approx} 10{sup -6}). Considerable attention also has been focused on improving the laser damage resistance to polished optical glass surfaces. Studies have shown that laser-induced damage to surfaces grows exponentially with the number of shots when illuminated with nano-second pulses at 351-nm above a given fluence threshold. A new approach for reducing and eliminating laser-induced surface damage relies on a series of post-polishing treatment steps. This damage improvement method is briefly reviewed.

  1. Passive and Active Protective Clothing against High-Power Laser Radiation

    Science.gov (United States)

    Hennigs, C.; Hustedt, M.; Kaierle, S.; Wenzel, D.; Markstein, S.; Hutter, A.

    The main objective of the work described in this paper was the development of passive and active protective clothing for the protection of the human skin against accidental laser irradiation and of active protective curtains. Here, the passive systems consist of functional multi-layer textiles, providing a high level of passive laser resistance. In addition, the active functional multi-layer textiles incorporate sensors that detect laser exposure and are, by means of a safety control, able to deactivate the laser beam automatically.Due to the lack of regulations for testing and qualifying textiles to be used as laser PPE, test methods were defined and validated. Additionally, corresponding testing set-ups were developed.Finally, the gap with respect to standardization was bridged by the definition of a test procedure and the requirements with respect to laser PPE.The developments were demonstrated by a set of tailored functional passive and active laser-protective clothing prototypes (gloves, jackets, aprons, trousers) and active curtains as well as by a prototype testing rig, providing the possibility to perform the specified low-power and high-power textile test procedure.

  2. Temperature evaluation of dental implant surface irradiated with high-power diode laser.

    Science.gov (United States)

    Rios, F G; Viana, E R; Ribeiro, G M; González, J C; Abelenda, A; Peruzzo, D C

    2016-09-01

    The prevalence of peri-implantitis and the absence of a standard approach for decontamination of the dental implant surface have led to searches for effective therapies. Since the source of diode lasers is portable, has reduced cost, and does not cause damage to the titanium surface of the implant, high-power diode lasers have been used for this purpose. The effect of laser irradiation on the implants is the elevation of the temperature surface. If this elevation exceeds 47 °C, the bone tissue is irreversibly damaged, so for a safety therapy, the laser parameters should be controlled. In this study, a diode laser of GaAsAl was used to irradiate titanium dental implants, for powers 1.32 to 2.64 W (real) or 2.00 to 4.00 W (nominal), in continuous/pulsed mode DC/AC, with exposure time of 5/10 s, with/without air flow for cooling. The elevation of the temperature was monitored in real time in two positions: cervical and apical. The best results for decontamination using a 968-nm diode laser were obtained for a power of 1.65 and 1.98 W (real) for 10 s, in DC or AC mode, with an air flow of 2.5 l/min. In our perspective in this article, we determine a suggested approach for decontamination of the dental implant surface using a 968-nm diode laser.

  3. Beam-shaping technique for improving the beam quality of a high-power laser-diode stack.

    Science.gov (United States)

    Gao, Xin; Ohashi, Hiroyuki; Okamoto, Hiroshi; Takasaka, Masaomi; Shinoda, Kazunori

    2006-06-01

    We report a beam-shaping technique that reconfigures the beams to improve the beam quality and enhance the power density for a ten-array high-power laser-diode stack by using two optical rectangular cubes and two stripe-mirror plates. The reshaped beam has threefold improvement in beam quality, and its power density is effectively enhanced. On the basis of this technique, we focus the beam of the high-power laser-diode stack to effectively end pump a high-power fiber laser.

  4. Rational Chebyshev Spectral Transform for the dynamics of high-power laser diodes

    CERN Document Server

    Javaloyes, J

    2014-01-01

    This manuscript details the use of the rational Chebyshev transform for describing the transverse dynamics of high-power laser diodes, either broad area lasers, index guided lasers or monolithic master oscillator power amplifier devices. This spectral method can be used in combination with the delay algebraic equation approach developed in \\cite{JB-OE-12}, which allows to substantially reduce the computation time. The theory is presented in such a way that it encompasses the case of the Fourier spectral transform presented in \\cite{PJB-JSTQE-13} as a particular case. It is also extended to the consideration of index guiding with an arbitrary profile. Because their domain of definition is infinite, the convergence properties of the Chebyshev Rational functions allow handling the boundary conditions with higher accuracy than with the previously studied Fourier method. As practical examples, we solve the beam propagation problem with and without index guiding: we obtain excellent results and an improvement of th...

  5. Numerical study of high-power semiconductor lasers for operation at sub-zero temperatures

    Science.gov (United States)

    Hasler, K. H.; Frevert, C.; Crump, P.; Erbert, G.; Wenzel, H.

    2017-04-01

    We present results on the impact of the Al-content in the waveguide structure on the electro-optical characteristics of 9xx nm, GaAs-based high-power lasers operated at room (300 K) and at sub-zero (200 K) heat sink temperatures. Experimentally a strong improvement of conversion efficiency and output power has been found if the lasers are cooled down. Numerical simulations using a software tool which solves the thermo-dynamic based drift-diffusion equations are able to reproduce the experimental findings. The reasons for the improved performance at lower temperatures are the enhancement of the modal gain and the reduced accumulation of electrons in the p-confinement layers resulting in a reduction of the leakage current. The latter allows the realization of lasers with a reduced Al content having a smaller series resistance and thus further enlarged conversion efficiency at sub-zero temperatures.

  6. High Power Electron Beam Injectors for 100 kW Free Electron Lasers

    Energy Technology Data Exchange (ETDEWEB)

    Todd, Alan; Bluem, Hans; Christina, Vincent; Cole, Michael; Rathke, John; Schultheiss, Tom; Colestock, Patrick; Kelley, J.P.; Kurennoy, Sergey; Nguyen, Dung; Russell, S.; Schrage, Dale; Wood, R.L.; Young, L.M.; Campisi, Isidoro; Daly, Edward; Douglas, David; Neil, George; Preble, Joseph; Rimmer, Robert; Rode, Claus; Sekutowicz, Jacek; Whitlatch, Timothy; Wiseman, Mark

    2003-05-01

    A key technology issue on the path to high-power FEL operation is the demonstration of reliable, highbrightness, high-power injector operation. We describe two ongoing programs to produce 100 mA injectors as drivers for 100 kW free-electron lasers. In one approach, in collaboration with the Thomas Jefferson National Accelerator Facility, we are fabricating a 750 MHz superconducting RF cryomodule that will be integrated with a room-temperature DC photocathode gun [1] and tested at the Laboratory. In the other approach, in collaboration with Los Alamos National Laboratory, a high-current 700 MHz, normal-conducting, RF photoinjector [2,3] is being designed and will undergo thermal management testing at the Laboratory. We describe the design, the projected performance and the status of both injectors.

  7. High-power beam injectors for 100 KW free-electron lasers

    Energy Technology Data Exchange (ETDEWEB)

    Todd, A. M. (Alan M.); Wood R. L. (Richard L.); Bluem, H.; Young, L. M. (Lloyd M.); Wiseman, M. (Mark); Schultheiss, T. (Thomas); Schrage, D. L. (Dale L.); Russell, S. J. (Steven J.); Rode, C. H.; Rimmer, R. (Robert); Nguyen, D. C. (Dinh C.); Kelley, J. P. (John Patrick); Kurennoy, S. (Sergey); wood, r

    2003-01-01

    A key technology issue on the path to high-power FEL operation is the demonstration of reliable, high-brightness, high-power injector operation. We describe two ongoing programs to produce 100 mA injectors as drivers for 100 kW free-electron lasers. In one approach, in collaboration with the Thomas Jefferson National Accelerator Facility, we are fabricating a 750 MHz superconducting RF cryomodule that will be integrated with a room-temperature DC photocathode gun and tested at the Laboratory. In the other approach, in collaboration with Los Alamos National Laboratory, a high-current 700 MHz, normal-conducting, RF photoinjector is being designed and will undergo thermal management testing at the Laboratory. We describe the design, the projected performance and the status of both injectors.

  8. High Power Amplifiers Chain nonlinearity influence on the accelerating beam stability in free electron laser (FLASH)

    CERN Document Server

    Cichalewski, w

    2010-01-01

    The high power amplifiers transfer characteristics nonlinearities can have a negative influence on the overall system performance. This is also true for the TESLA superconducting cavities accelerating field parameters control systems. This Low Level Radio Frequency control systems uses microwave high power amplifiers (like 10 MW klystrons) as actuators in the mentioned feedback loops. The amplitude compression and phase deviations phenomena introduced to the control signals can reduce the feedback performance and cause electron beam energy instabilities. The transfer characteristics deviations in the Free Electron Laser in Hamburg experiment have been investigated. The outcome of this study together with the description of the developed linearization method based on the digital predistortion approach have been described in this paper. Additionally, the results from the linearization tool performance tests in the FLASH's RF systems have been placed.

  9. High-power laser delocalization in plasmas leading to long-range beam merging

    Energy Technology Data Exchange (ETDEWEB)

    Nakatsutsumi, M.; Marques, J.R.; Antici, P.; Bourgeois, N.; Romagnani, L.; Audebert, P.; Fuchs, J. [UPMC, CEA, CNRS, LULI, Ecole Polytech, F-91128 Palaiseau (France); Nakatsutsumi, M.; Kodama, R. [Osaka Univ, Grad Sch Engn, Suita, Osaka 5650871 (Japan); Antici, P. [Univ Roma La Sapienza, Dipartimento SBAI, I-00161 Rome (Italy); Feugeas, J.L.; Nicolai, P. [Univ Bordeaux 1, CNRS, CEA, Ctr Lasers Intenses and Applicat, F-33405 Talence (France); Lin, T. [Fox Chase Canc Ctr, Philadelphia, PA 19111 (United States)

    2010-07-01

    Attraction and fusion between co-propagating light beams, mutually coherent or not, can take place in nonlinear media as a result of the beam power modifying the refractive index of the medium. In the context of high-power light beams, induced modifications of the beam patterns could potentially impact many topics, including long-range laser propagation, the study of astrophysical colliding blast waves and inertial confinement fusion. Here, through experiments and simulations, we show that in a fully ionized plasma, which is a nonlinear medium, beam merging can take place for high-power and mutually incoherent beams that are initially separated by several beam diameters. This is in contrast to the usual assumption that this type of interaction is limited to beams separated by only one beam diameter. This effect, which is orders of magnitude more significant than Kerr-like nonlinearity in gases, demonstrates the importance of potential cross-talk amongst multiple beams in plasma. (authors)

  10. Robust cladding light stripper for high-power fiber lasers using soft metals.

    Science.gov (United States)

    Babazadeh, Amin; Nasirabad, Reza Rezaei; Norouzey, Ahmad; Hejaz, Kamran; Poozesh, Reza; Heidariazar, Amir; Golshan, Ali Hamedani; Roohforouz, Ali; Jafari, S Naser Tabatabaei; Lafouti, Majid

    2014-04-20

    In this paper we present a novel method to reliably strip the unwanted cladding light in high-power fiber lasers. Soft metals are utilized to fabricate a high-power cladding light stripper (CLS). The capability of indium (In), aluminum (Al), tin (Sn), and gold (Au) in extracting unwanted cladding light is examined. The experiments show that these metals have the right features for stripping the unwanted light out of the cladding. We also find that the metal-cladding contact area is of great importance because it determines the attenuation and the thermal load on the CLS. These metals are examined in different forms to optimize the contact area to have the highest possible attenuation and avoid localized heating. The results show that sheets of indium are very effective in stripping unwanted cladding light.

  11. Ultra-flat supercontinuum generated from high-power, picosecond telecommunication fiber laser source.

    Science.gov (United States)

    Liao, Ruoyu; Song, Youjian; Zhou, Xiaokang; Chai, Lu; Wang, Chingyue; Hu, Minglie

    2016-11-20

    An ultra-flat, high-power supercontinuum generated from a picosecond telecommunication fiber laser was presented. The pulse from a carbon nanotube mode-locked oscillator was amplified using an Er-Yb codoped fiber amplifier. The output of the system achieved an average power of 2.7 W, with the center wavelength at 1564 nm and a FWHM of 6 nm in the spectral domain. By passing this amplified high-power pulse through a 4.6 m highly nonlinear photonic crystal fiber, an ultra-flat supercontinuum spanning 1600-2180 nm is generated. And the average power of the supercontinuum achieves 1 W.

  12. Energy coupling and plume dynamics during high power laser heating of metals

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, S. [Univ. of California, Berkeley, CA (United States). Dept. of Mechanical Engineering]|[Lawrence Berkeley National Lab., CA (United States). Environmental Energy Technologies Div.

    1997-05-01

    High power laser heating of metals was studied utilizing experimental and numerical methods with an emphasis on the laser energy coupling with a target and on the dynamics of the laser generated vapor flow. Rigorous theoretical modeling of the heating, melting, and evaporation of metals due to laser radiation with a power density below the plasma shielding threshold was carried out. Experimentally, the probe beam deflection technique was utilized to measure the propagation of a laser induced shock wave. The effects of a cylindrical cavity in a metal surface on the laser energy coupling with a solid were investigated utilizing photothermal deflection measurements. A numerical calculation of target temperature and photothermal deflection was performed to compare with the measured results. Reflection of the heating laser beam inside the cavity was found to increase the photothermal deflection amplitude significantly and to enhance the overall energy coupling between a heating laser beam and a solid. Next, unsteady vaporization of metals due to nanosecond pulsed laser heating with an ambient gas at finite pressure was analyzed with a one dimensional thermal evaporation model for target heating and one dimensional compressible flow equations for inviscid fluid for the vapor flow. Lastly, the propagation of a shock wave during excimer laser heating of aluminum was measured with the probe beam deflection technique. The transit time of the shock wave was measured at the elevation of the probe beam above the target surface; these results were compared with the predicted behavior using ideal blast wave theory. The propagation of a gaseous material plume was also observed from the deflection of the probe beam at later times.

  13. Magnetic nanoparticles for biophysical applications synthesized by high-power physical dispersion

    Science.gov (United States)

    Safronov, A. P.; Beketov, I. V.; Tyukova, I. S.; Medvedev, A. I.; Samatov, O. M.; Murzakaev, A. M.

    2015-06-01

    The low cost and high output methods of high-power physical dispersion: the electrical explosion of wire and the laser target evaporation were elaborated for the production of iron oxide magnetic nanoparticles (MNPs) with controlled dispersion parameters and highly reproducible functional properties. The synthesized MNPs were spherical in shape with mean diameter 10 nm and lognormal particle size distribution. The phase composition, shape, particle size and functional properties of MNPs were cross-examined by a variety of contemporary experimental techniques. The phase structure of MNPs corresponds to the inverse spinel of magnetite. Meanwhile, due to the non-equilibrium conditions of the dispersion chemical composition of MNPs is close to maghemite-γ-Fe2O3. Their magnetic properties are reproducible and very close to the single domain superparamagnetic behavior. The stability of the suspensions of these MNPs and their applicability in the biophysical purposes such as magneto-induced heating have been demonstrated.

  14. A high power lithium thionyl chloride battery for space applications

    Science.gov (United States)

    Shah, Pinakin M.

    1993-03-01

    A high power, 28 V, 330 A h, active lithium thionyl chloride battery has been developed for use as main and payload power sources on an expendable launch vehicle. Nine prismatic cells, along with the required electrical components and a built-in heater system, are efficiently packaged resulting in significant weight savings over presently used silver-zinc batteries. The high rate capability is achieved by designing the cells with a large electrochemical surface area and impregnating an electrocatalyst, polymeric phthalocyanine, into the carbon cathodes. Passivation effects are reduced with the addition of sulfur dioxide into the thionyl chloride electrolyte solution. The results of conducting a detailed thermal analysis are utilized to establish the heater design parameters and the thermal insulation requirements of the battery. An analysis of cell internal pressure and vent characteristics clearly illustrates the margins of safety under different operating conditions. Performance of fresh cells is discussed using polarization scan and discharge data at different rates and temperatures. Self-discharge rate is estimated based upon test results on cells after storage. Results of testing a complete prototype battery are described.

  15. High-power diode-end-pumped Tm:YLF slab laser delivering 189 W at 1890 nm

    CSIR Research Space (South Africa)

    Koen, W

    2010-09-01

    Full Text Available The authors present a high-power Tm:YLF slab laser double-end-pumped by two 300 W laser diode stacks. The resonator was designed such that the laser emitted at 1890 nm instead of the conventional operating wavelength of 1912 nm. At full incident...

  16. Efficient generation of 3.5W laser light at 515nm by frequency doubling a single-frequency high power DBR tapered diode laser

    DEFF Research Database (Denmark)

    Jensen, Ole Bjarlin; Hansen, Anders Kragh; Müller, André

    2017-01-01

    More than 3.5 W of green light at 515 nm is generated by frequency doubling a single-frequency high power DBR tapered diode laser. The frequency doubling is performed in a cascade of PPMgLN and PPMgSLT crystals in order to reach high power and avoid thermal effects present in PPMgLN at high power...

  17. Wide aperture piezoceramic deformable mirrors for aberration correction in high-power lasers

    Institute of Scientific and Technical Information of China (English)

    Vadim Samarkin; Alexander Alexandrov; Gilles Borsoni; Takahisa Jitsuno; Pavel Romanov; Aleksei Rukosuev; Alexis Kudryashov

    2016-01-01

    The deformable mirror with the size of 410 mmstacks was developed. The results ×468 mm controlled by the bimorph piezoceramic plates and multilayer piezoceramic of the measurements of the response functions of all the actuators and of the surface shape of the deformable mirror are presented in this paper. The study of the mirror with a Fizeau interferometer and a Shack–Hartmann wavefront sensor has shown that it was possible to improve the flatness of the surface down to a residual roughness of 0.033 μm(RMS). The possibility of correction of the aberrations in high-power lasers was numerically demonstrated.

  18. Reflective Optical Chopper Used in NIST High-Power Laser Measurements

    Directory of Open Access Journals (Sweden)

    Cromer, Chris

    2008-11-01

    Full Text Available For the past ten years, NIST has used high-reflectivity, optical choppers as beamsplitters and attenuators when calibrating the absolute responsivity and response linearity of detectors used with high-power CW lasers. The chopper-based technique has several advantages over the use of wedge-shaped transparent materials (usually crystals often used as beam splitters in this type of measurement system. We describe the design, operation and calibration of these choppers. A comparison between choppers and transparent wedge beampslitters is also discussed.

  19. High-power laser interaction with low-density C–Cu foams

    Energy Technology Data Exchange (ETDEWEB)

    Pérez, F.; Colvin, J. D.; May, M. J.; Charnvanichborikarn, S.; Kucheyev, S. O.; Fournier, K. B., E-mail: fournier2@llnl.gov [Lawrence Livermore National Laboratory, 7000 East Ave., Livermore, California 94550 (United States); Felter, T. E. [Sandia National Laboratories, 7011 East Ave., Livermore, California 94550 (United States)

    2015-11-15

    We study the propagation of high-power laser beams in micro-structured carbon foams by monitoring the x-ray output from deliberately introduced Cu content. In particular, we characterize this phenomenon measuring absolute time-resolved x-ray yields, time-resolved x-ray imaging, and x-ray spectroscopy. New experimental results for C–Cu foams show a faster heat front velocity than simulation that assumed homogeneous plasma. We suggest the foam micro-structure may explain this trend.

  20. High-power laser interaction with low-density C-Cu foams

    Science.gov (United States)

    Pérez, F.; Colvin, J. D.; May, M. J.; Charnvanichborikarn, S.; Kucheyev, S. O.; Felter, T. E.; Fournier, K. B.

    2015-11-01

    We study the propagation of high-power laser beams in micro-structured carbon foams by monitoring the x-ray output from deliberately introduced Cu content. In particular, we characterize this phenomenon measuring absolute time-resolved x-ray yields, time-resolved x-ray imaging, and x-ray spectroscopy. New experimental results for C-Cu foams show a faster heat front velocity than simulation that assumed homogeneous plasma. We suggest the foam micro-structure may explain this trend.

  1. The project of the high power free electron laser based on the race-track microtron-recuperator

    Science.gov (United States)

    Vinokurov, N. A.; Gavrilov, N. G.; Gorniker, E. I.; Kulipanov, G. N.; Kuptsov, I. V.; Kurkin, G. Ya.; Erg, G. I.; Levashov, Yu. I.; Oreshkov, A. D.; Petrov, S. P.; Petrov, V. M.; Pinayev, I. V.; Popik, V. M.; Sedlyarov, I. K.; Shaftan, T. V.; Skrinsky, A. N.; Sokolov, A. S.; Veshcherevich, V. G.; Vobly, P. D.

    1995-02-01

    To provide a user facility for the Siberian Centre of Photochemical Researches in Novosibirsk a high power free electron laser is under construction. The project status and installation are described.

  2. High-energy molecular lasers self-controlled volume-discharge lasers and applications

    CERN Document Server

    Apollonov, V V

    2016-01-01

    This book displays the physics and design of high-power molecular lasers. The lasers described are self-controlled volume-discharge lasers. The book explains self-sustained discharge lasers, self-initiated discharge lasers and technical approaches to laser design. Important topics discussed are laser efficiency, laser beam quality and electric field homogeneity. The book contains many new innovative applications.

  3. High-Power Density SOFCs for Aviation Applications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — As solid oxide fuel cells (SOFCs) approach commercialization, interest in broader applications of this technology is mounting. While the first commercialized systems...

  4. Numerical Simulations on Buckling Failure of Preloaded Cylindrical Shell Irradiated by High Power Laser Beam

    Institute of Scientific and Technical Information of China (English)

    王吉; 王肖钧; 王峰; 赵凯

    2004-01-01

    With finite-element software ANSYS 7.0 and simple thermal-mechanical coupling constitutive relations,the buckling failure of preloaded cylindrical shell irradiated by high power laser beam was studied by numerical simulations. The buckling mode and buckling critical loading were analysed for different preloading conditions. The influence of laser intensity, beam irradiation time, preloading conditions and geometric parameters of cylindrical shell on the buckling mode were discussed. The numerical results show that: ① the buckling deformation of the cylindrical shell was concentrated in the area of laser spot and the radial buckling was the main buckling mode, ② a linear relationship between the buckling eigenvalue and the maximum temperature at the center of laser spot was approached, ③ the buckling failure of cylindrical shell was attributed to the coupling effect of the material softening and the radial deformation in the laser spot, and hence to raise the stiffness of the material would enhance the ability for anti-irradiation of structure substantially.

  5. Development of a two arm, high energy, high power laser for plasma research in India

    Science.gov (United States)

    Joshi, A. S.; Kamath, M. P.; Sharma, A. K.; Raghuramaiah, M. R.; Patidar, R. K.; Ansari, M. S.; Sreedhar, N.; Chandra, R.; Navathe, C. P.; Naik, P. A.; Gupta, P. D.

    2013-11-01

    We report here work done towards development of a two arm, high energy, high power Nd:phosphate glass laser system. One arm of the laser is proposed to be operated in a long pulse (˜1.5ns pulse duration) with an energy of ˜400 J. Presently, this arm of the laser is operating at energy of ˜100 J after a disc amplifier that amplifies the laser beam of diameter ˜94 mm. After the addition of two more disc amplifiers which are nearing completion, the laser beam will have energy of ˜400 J, with a beam diameter 140 mm, at an intensity of ˜2 GW/cm2. This beam will be converted to its second harmonic using a 2 × 2 array KDP crystals. The second arm, under development, will operate with a hybrid amplification scheme using optical parametric chirped pulse amplification (OPCPA) and conventional amplification using the existing Nd:glass amplifiers to produce 50 TW, 25 J, 500 fs pulse. A tiled triangular pulse compressor is under development for compressing the stretched pulse.

  6. Generation of neutral atomic beams utilizing photodetachment by high power diode laser stacks

    Science.gov (United States)

    O'Connor, A. P.; Grussie, F.; Bruhns, H.; de Ruette, N.; Koenning, T. P.; Miller, K. A.; Savin, D. W.; Stützel, J.; Urbain, X.; Kreckel, H.

    2015-11-01

    We demonstrate the use of high power diode laser stacks to photodetach fast hydrogen and carbon anions and produce ground term neutral atomic beams. We achieve photodetachment efficiencies of ˜7.4% for H- at a beam energy of 10 keV and ˜3.7% for C- at 28 keV. The diode laser systems used here operate at 975 nm and 808 nm, respectively, and provide high continuous power levels of up to 2 kW, without the need of additional enhancements like optical cavities. The alignment of the beams is straightforward and operation at constant power levels is very stable, while maintenance is minimal. We present a dedicated photodetachment setup that is suitable to efficiently neutralize the majority of stable negative ions in the periodic table.

  7. Removal of graffiti from quarry stone by high power diode laser

    Science.gov (United States)

    Penide, J.; Quintero, F.; Riveiro, A.; Sánchez-Castillo, A.; Comesaña, R.; del Val, J.; Lusquiños, F.; Pou, J.

    2013-04-01

    The integrity of architectural monuments in urban areas is threatened by numerous attacks, among which the graffiti is sometimes one of the most important. Particularly, Morelia's historic center (Mexico) (appointed World Heritage Site by UNESCO) suffers, for some years, a high number of graffiti. Most of these monuments in Morelia were built using a local stone called Pink Morelia Quarry. In this paper, we present the results of a study on the feasibility to remove the graffiti from Pink Morelia Quarry using a high power diode laser treatment. An extensive experimental analysis of the operating conditions has been carried out leading to successful results. The optimal parameters to achieve a total removal of graffiti have been determined. We concluded that continuous wave regime leads to better results than modulated wave regime, additionally, a two laser passes process demonstrated a high performance.

  8. High Power Laser Beam Welding of Thick-walled Ferromagnetic Steels with Electromagnetic Weld Pool Support

    Science.gov (United States)

    Fritzsche, André; Avilov, Vjaceslav; Gumenyuk, Andrey; Hilgenberg, Kai; Rethmeier, Michael

    The development of modern high power laser systems allows single pass welding of thick-walled components with minimal distortion. Besides the high demands on the joint preparation, the hydrostatic pressure in the melt pool increases with higher plate thicknesses. Reaching or exceeding the Laplace pressure, drop-out or melt sagging are caused. A contactless electromagnetic weld support system was used for laser beam welding of thick ferromagnetic steel plates compensating these effects. An oscillating magnetic field induces eddy currents in the weld pool which generate Lorentz forces counteracting the gravity forces. Hysteresis effects of ferromagnetic steels are considered as well as the loss of magnetization in zones exceeding the Curie temperature. These phenomena reduce the effective Lorentz forces within the weld pool. The successful compensation of the hydrostatic pressure was demonstrated on up to 20 mm thick plates of duplex and mild steel by a variation of the electromagnetic power level and the oscillation frequency.

  9. Effect of high-power nanosecond and femtosecond laser pulses on silicon nanostructures

    Energy Technology Data Exchange (ETDEWEB)

    Kachurin, G. A., E-mail: kachurin@isp.nsc.ru; Cherkova, S. G.; Volodin, V. A.; Marin, D. V. [Russian Academy of Sciences, Institute of Semiconductor Physics, Siberian Branch (Russian Federation); Deutschmann, M. [Laser Zentrum Hannover (Germany)

    2008-02-15

    The effect of high-power nanosecond (20 ns) and femtosecond (120 fs) laser pulses on silicon nanostructures produced by ion-beam-assisted synthesis in SiO{sub 2} layers or by deposition onto glassy substrates is studied. Nanosecond annealing brings about a photoluminescence band at about 500 mn, with the intensity increasing with the energy and number of laser pulses. The source of the emission is thought to be the clusters of Si atoms segregated from the oxide. In addition, the nanosecond pulses allow crystallization of amorphous silicon nanoprecipitates in SiO{sub 2}. Heavy doping promotes crystallization. The duration of femtosecond pulses is too short for excess Si to be segregated from SiO{sub 2}. At the same time, such short pulses induce crystallization of Thin a-Si films on glassy substrates. The energy region in which crystallization is observed for both types of pulses allows short-term melting of the surface layer.

  10. Spectroscopic analysis of packaging concepts for high-power diode laser bars

    Science.gov (United States)

    Hempel, Martin; Ziegler, Mathias; Schwirzke-Schaaf, Sandy; Tomm, Jens W.; Jankowski, Denny; Schröder, Dominic

    2012-05-01

    Double-side cooled high-power diode laser bars packaged by different techniques on different types of passive heat sinks are analyzed in terms of packaging-induced strain. Reference data from standard devices being single-side cooled only and packaged by conventional soft and hard soldering are also presented. Thermal profiling across the devices complements the results. The most suitable packaging architecture and technique for double-side cooled bars is identified. Measurements of the laser emission near field and electroluminescence pattern provide direct reference to the functionality of the devices. Furthermore, a type of cross calibration of the methods used for strain analysis is made, since all techniques are applied to the same set of bars. This involves micro photoluminescence, micro Raman, and degree-of-polarization electroluminescence spectroscopy.

  11. Generation of neutral atomic beams utilizing photodetachment by high power diode laser stacks

    CERN Document Server

    O'Connor, A P; Grussie, F; Koenning, T P; Miller, K A; de Ruette, N; Stützel, J; Savin, D W; Urbain, X; Kreckel, H

    2015-01-01

    We demonstrate the use of high power diode laser stacks to photodetach fast hydrogen and carbon anions and produce ground term neutral atomic beams. We achieve photodetachment efficiencies of $\\sim$7.4\\% for H$^-$ at a beam energy of 10\\,keV and $\\sim$3.7\\% for C$^-$ at 28\\,keV. The diode laser systems used here operate at 975\\,nm and 808\\,nm, respectively, and provide high continuous power levels of up to 2\\,kW, without the need of additional enhancements like optical cavities. The alignment of the beams is straightforward and operation at constant power levels is very stable, while maintenance is minimal. We present a dedicated photodetachment setup that is suitable to efficiently neutralize the majority of stable negative ions in the periodic table.

  12. Thermal effects in high-power Nd:YAG disk-type solid state laser

    Science.gov (United States)

    Yang, Huomu; Feng, Guoying; Zhou, Shouhuan

    2011-09-01

    An investigation of thermal effects in a high-power Nd:YAG disk-type solid state laser pumped with different pump beam transverse profiles is carried out by numerical simulation based on the finite element method (FEM). Impact of the heat sink on the thermal effects is included in the simulation. The distribution of first principle stress, thermally induced birefringence, including the distribution and variation of the birefringence loss, are studied. The characteristics of the phase variation are analyzed with consideration of the temperature gradient, deformation, strain and thermal stress. Thermal lensing is explored as a function of pump power and of the radius pumped with different pump beam transverse profiles. The non-parabolic part of optical phase distortion is simulated. Furthermore, the characteristics of the bi-focus of the disk laser are also studied. Experiments on the maximum tensile stress distribution and depolarization loss are carried out. The presented calculations are in qualitative agreement with the experimental observations.

  13. High Power Tm3+-Doped Fiber Lasers Tuned by a Variable Reflective Output Coupler

    Directory of Open Access Journals (Sweden)

    Yulong Tang

    2008-01-01

    Full Text Available Wide wavelength tuning by a variable reflective output coupler is demonstrated in high-power double-clad Tm3+-doped silica fiber lasers diode-pumped at ∼790  nm. Varying the output coupling from 96% to 5%, the laser wavelength is tuned over a range of 106  nm from 1949 to 2055  nm. The output power exceeds 20  W over 90-nm range and the maximum output power is 32  W at 1949  nm for 51-W launched pump power, corresponding to a slope efficiency of ∼70%. Assisted with different fiber lengths, the tuning range is expanded to 240  nm from 1866 to 2107  nm with the output power larger than 10  W.

  14. Energy measurement system of a large-aperture high power laser experiment platform

    Institute of Scientific and Technical Information of China (English)

    Yanwen; Xia; Yue; Liang; Sen; Li; Junpu; Zhao; Zhitao; Peng; Hongguang; Li; Hua; Liu; Zhihong; Sun; Kuixing; Zheng; Xiaofeng; Wei

    2013-01-01

    An energy measurement system in a large-aperture high power laser experiment platform is introduced. The entire measurement system includes five calorimeters, which carry out the energy measurement of the fundamental frequency before the frequency conversion unit, remaining fundamental frequency, remaining second-harmonics, third-harmonics,as well as the energy balance measurement after the frequency conversion unit. Combinational indirect calibration and direct calibration are employed to calibrate the sampling coefficients of the calorimeters. The analysis of the data showed that, regarding the energy balance coefficients, combinational calibration approach gives a higher precision, and leads to an energy balance with 1%; and regarding the energy sampling coefficients for the various wavelengths after the frequency conversion, the results from direct and combinational calibration are consistent. The uncertainties for all energy sampling coefficients are within 3%, which guarantees the reliability of the energy measurement for the laser facility.

  15. High-power laser arrays with 100% fill factor emission facet

    Science.gov (United States)

    Yanson, Dan A.; McDougall, Stewart D.; Qiu, Bocang; Loyo-Maldonado, Valentin; Bacchin, Gianluca; Robertson, Stephen; Bon, Sébastien; Marsh, John H.

    2008-02-01

    Novel types of laser diode array with a 100% filling factor at the emission facet are reported. The arrays utilize both parallel and tapered cavity emitters that are connected via a common Laterally Unconfined Non-Absorbing Mirror (LUNAM) defined with quantum-well intermixing technology at 808 nm wavelength. Two LUNAM array types are considered: incoherent (weakly coupled) and coherent (diffraction coupled). Incoherent LUNAM arrays benefit from a reduced power density at the facet, improving reliability, and a near-uniform intensity distribution across the array aperture. Stacked laser diode arrays built with LUNAM bars deliver 950 W power under QCW operation with monolithically integrated LUNAM Talbot cavity. The devices produce a single-lobed horizontal far-field pattern over a limited current range with <10% slope efficiency penalty compared to an uncoupled case. The LUNAM arrays are promising candidates for high-power, high-brightness and high-reliability operation.

  16. High-power green light generation by second harmonic generation of single-frequency tapered diode lasers

    DEFF Research Database (Denmark)

    Jensen, Ole Bjarlin; Andersen, Peter E.; Sumpf, Bernd

    2010-01-01

    We demonstrate the generation of high power (>1.5W) and single-frequency green light by single-pass second harmonic generation of a high power tapered diode laser. The tapered diode laser consists of a DBR grating for wavelength selectivity, a ridge section and a tapered section. The DBR tapered...... laser emits in excess of 9 W single-frequency output power with a good beam quality. The output from the tapered diode laser is frequency doubled using periodically poled MgO:LiNbO3. We investigate the modulation potential of the green light and improve the modulation depth from 1:4 to 1:50....

  17. High-power green light generation by second harmonic generation of single-frequency tapered diode lasers

    DEFF Research Database (Denmark)

    Jensen, Ole Bjarlin; Andersen, Peter E.; Sumpf, Bernd;

    2010-01-01

    laser emits in excess of 9 W single-frequency output power with a good beam quality. The output from the tapered diode laser is frequency doubled using periodically poled MgO:LiNbO3. We investigate the modulation potential of the green light and improve the modulation depth from 1:4 to 1:50.......We demonstrate the generation of high power (>1.5W) and single-frequency green light by single-pass second harmonic generation of a high power tapered diode laser. The tapered diode laser consists of a DBR grating for wavelength selectivity, a ridge section and a tapered section. The DBR tapered...

  18. Spectral diagnostics of a vapor-plasma plume produced during welding titanium with a high-power ytterbium fiber laser

    Science.gov (United States)

    Uspenskiy, S. A.; Petrovskiy, V. N.; Bykovskiy, D. P.; Mironov, V. D.; Prokopova, N. M.; Tret'yakov, E. V.

    2015-03-01

    This work is devoted to the research of welding plume during high power ytterbium fiber laser welding of a titanium alloy in the Ar shielding gas environment. High speed video observation of a vapor-plasma plume for visualization of processes occurring at laser welding was carried out. The coefficient of the inverse Bremsstrahlung absorption of laser radiation is calculated for a plasma welding plume by results of spectrometer researches. The conclusion deals with the impact of plasma on a high-power fiber laser radiation.

  19. Generation and application of high power flattened Gaussian beams

    CSIR Research Space (South Africa)

    Forbes, A

    2009-07-01

    Full Text Available .6 0.8 1 1.2 I n t e n s i t y ( a . u . ) 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 I n t e n s i t y ( a . u . ) The mode competition is revealed in the loss convergence per round trip 0 0... power Flattened Gaussian Beams A. Forbes1,2,3, N. du Preez4, I.A, Litvin1,3 and L.R. Botha1,3 1 CSIR National Laser Centre 2 School of Physics, University of KwaZulu-Natal 3 School of Physics, University of Stellenbosch 4 SDILasers (Pty) Ltd...

  20. Transmission characteristics of high-power 589-nm laser beam in photonic crystal fiber

    Science.gov (United States)

    Ito, Meguru; Hayano, Yutaka; Saito, Norihito; Akagawa, Kazuyuki; Kato, Mayumi; Saito, Yoshihiko; Takazawa, Akira; Takami, Hideki; Iye, Masanori; Wada, Satoshi; Colley, Stephen A.; Dinkins, Matthew C.; Eldred, Michael; Golota, Taras I.; Guyon, Olivier; Hattori, Masayuki; Oya, Shin; Watanabe, Makoto

    2006-06-01

    We are developing Laser Guide Star Adaptive Optics (LGSAO) system for Subaru Telescope at Hawaii, Mauna Kea. We achieved an all-solid-state 589.159 nm laser in sum-frequency generation. Output power at 589.159 nm reached 4W in quasi-continuous-wave operation. To relay the laser beam from laser location to laser launching telescope, we used an optical fiber because the optical fiber relay is more flexible and easier than mirror train. However, nonlinear scattering effect, especially stimulated Raman scattering (SRS) and stimulated Brillouin scattering (SBS), will happen when the inputted laser power increases, i.e., intensity at the fiber core exceed each threshold. In order to raise the threshold levels of each nonlinear scattering, we adopt photonic crystal fiber (PCF). Because the PCF can be made larger core than usual step index fiber (SIF), one can reduce the intensity in the core. We inputted the high power laser into the PCF whose mode field diameter (MFD) is 14 μm and the SIF whose MFD is 5 μm, and measured the transmission characteristics of them. In the case of the SIF, the SRS was happen when we inputted 2 W. On the other hand, the SRS and the SBS were not induced in the PCF even for an input power of 4 W. We also investigated polarization of the laser beam transmitting through the PCF. Because of the fact that the backscattering efficiency of exciting the sodium layer with a narrowband laser is dependent on the polarization state of the incident beam, we tried to control the polarization of the laser beam transmitted the PCF. We constructed the system which can control the polarization of input laser and measure the output polarization. The PCF showed to be able to assume as a double refraction optical device, and we found that the output polarization is controllable by injecting beam with appropriate polarization through the PCF. However, the Laser Guide Star made by the beam passed through the PCF had same brightness as the state of the polarization.

  1. High power excimer laser image relay system analysis using Delano diagram

    Science.gov (United States)

    Zhang, Yongshen; Zhao, Jun; Zhao, Xueqing; Hu, Yun; Wang, Dahui; Xue, Quanxi; Liu, Jingru

    2013-05-01

    The characteristics of Delano diagram are especially helpful in instrumental systems type with considerably separated components. For high power excimer laser system, especially for image relay scheme, the Delano diagram method is highly advantageous for the system's thin lens layout design. A primitive experimental image relay and it's combination optical layout is investigated in our high power XeCl laser system, with intensity smoothed spatial incoherent source. Instead of the uniform intensity distribution on the target as expected, it is obvious shows in the final image on the target that a gauss like intensity profile and a large amount of astigmatism results. There are two possible reasons: the first one is that not keeping proper relay of pupil plane (or Fourier plane) in the final stage, simply care the collimated beam of virtual object in the final focusing stage. With the help of Delano diagram, it's clearly shown in the diagram that the Fourier plane and the image plane come very close, indicates that a complete image relay of the object plane and Fourier plane is needed. The second reason is due to the off-axis setup in the large aperture main amplifier, which introduce significant astigmatism aberrations in the final optical path. This question can be solved using proper tilt and de-center of reflective mirror pair setup, and two possible such combination pairs are proposed.

  2. High photon flux XUV and soft x-ray sources enabled by high harmonic generation of high power fiber lasers

    Science.gov (United States)

    Rothhardt, Jan; Hädrich, Steffen; Krebs, Manuel; Limpert, Jens; Tünnermann, Andreas

    2015-07-01

    This contribution reports on the recent advances in high harmonic generation (HHG) with high power femtosecond fiber lasers at high repetition rates. The capabilities of high power fiber lasers, the challenges of phase matching in the tight-focusing regime and recent experimental results will be discussed. In particular, post compressed pules as short as 30 fs, with ~150 μJ pulse energy at 0.6 MHz repetition rate have been used for efficient HHG into the XUV. Despite the tight focusing phase matching is ensured by providing the target gas with adequately high density. A conversion efficiency in excess of 10-6 at ~30 eV has been achieved in xenon gas. This resulted in more than 100μW of average power (>1013 photons per second), which represents the highest photon flux achieved by any HHG source in this spectral region so far. In addition, further pulse compression yielded few-cycle pulses at high average power that have enabled efficient soft Xray generation in neon and helium. HHG in neon provided more than 3·109 photons/s within a 1% bandwidth at 120 eV and helium allowed for HHG up to the water window spectral region beyond 283 eV. These compact sources provide highest photon flux on a table-top and will enable exciting applications such as nanometer-resolution imaging or coincidence spectroscopy in the near future.

  3. Study of interaction of high-power Ar$^+$ laser beam with Ag$^+$-doped glass

    CERN Document Server

    Nahal, A; Payami, M

    2003-01-01

    In this work, we have investigated the interaction of a high-power Ar$^+$ laser beam, in a continuous multi-line regime, with Ag$^+$-doped glass samples. The samples were subjected to the irradiation after the ion-exchange step. As a result of the irradiation, a peak appears in the absorption spectrum; its evolution depends on both the exposure time and the laser beam power. Interaction of the beam with the clusters causes them break into smaller ones which has been confirmed by optical absorption spectroscopy. Depending on the increment steps of the laser-beam power, different results are obtained. It is found that, in addition to the fragmentations of the nano-clusters, clusters of micro-meter size ($d\\sim 3\\mu m$) are formed in the sample, if the laser power is increased in a fast regime. The fragmentation processes have been explained in the framework of the density-functional theory with stabilized jellium model.

  4. Numerical analysis to four-wave mixing induced spectral broadening in high power fiber lasers

    Science.gov (United States)

    Feng, Yujun; Wang, Xiaojun; Ke, Weiwei; Sun, Yinhong; Zhang, Kai; Ma, Yi; Li, Tenglong; Wang, Yanshan; Wu, Juan

    2015-02-01

    For powers exceeding a threshold the spectral broadening in fiber amplifiers becomes a significant challenge for the development of high power narrow bandwidth fiber lasers. In this letter, we show that the spectral broadening can be partly caused by four-wave mixing(FWM) process in which the power of the central wavelength would transfer to the side ones. A practical FWM induced spectral broadening theory has been derived from the early works. A numerical model of fiber amplifier has been established and FWM process has been added to the model. During the simulation process, we find that when a 10 GHz, several watts narrow bandwidth laser is seeded into a few modes fiber laser amplifier, the FWM induced spectral broadening effect might continually increase the FWHM of the spectra of the continuum laser to 100 GHz within the amplification process to several hundred watts which has been convinced by our experiments. Some other results have also been analyzed in this paper to complete the four-wave mixing induced spectral broadening theory in fiber amplifiers.

  5. Surface error modeling of mounted large optics in high power laser system

    Science.gov (United States)

    Wang, Hui; Xiong, Zhao; Yuan, Xiaodong

    2016-10-01

    The surface form of mounted large optics has a very important impact on the laser beam performance in high power laser system. To make the surface form to the minimized distortion and keep with the design specifications is always a difficult challenge in China's SG-III laser system which is made up of thousands meter-sized large optical units and requires to focus all 48 laser beams into nearly 600 μm-diameter spot better than 50 μm (RMS) within a few picoseconds. In this paper, a methodology integrated both 3D finite elements modeling method and nanometer-level precision metrology is proposed to evaluate the surface performance. According to various spatial frequencies, the wavefront characters of large aperture optical component are measured and provided to analyze its mounted surface characters. Assembly and mounting process will be adjusted to meet for the surface wavefront requirements both of with the data both of measured when pre-alignment and predicted for installation. By a case study of large transport mirror, the proposed approach has shown a good performance on obtaining precise surface features and guiding the optical mounting.

  6. Bactericidal effects of high-power Nd:YAG laser radiation on Staphylococcus aureus

    Science.gov (United States)

    Yeo, C. B. Allen; Watson, Ian A.; Stewart-Tull, Duncan E. S.; Wardlaw, A. C.; Armstrong, Graham N.

    1998-05-01

    The effect of laser radiation on Staphylococcus aureus 6571 (Oxford strain) was studied with high-power Nd:YAG laser radiation between 50 and 300 W. A range of laser pulse repetition frequencies (PRF) from 5 to 30 Hz, with a combination of pulse energies from 2 to 30 J were applied; this covered a range of energy densities from 800 to 0963-9659/7/3/020/img8. The area of inactivation of S. aureus, lawned on nutrient agar plates, was quantified as a function of energy density and exposure time. The shortest exposure time which produced an area of inactivation equal to 50% of the beam area was achieved at a PRF of 30 Hz, pulse energy of 10 J, and with an exposure time of 10.75 s; this was equivalent to an applied energy density of 0963-9659/7/3/020/img9. No bacterial inactivation was observed at relatively low-power settings for PRF, pulse energies and exposure time of: 20 Hz, 3 J and 34 s; 25 Hz, 2 J and 45 s and 30 Hz, 2 J and 35 s, respectively. These results shows that pulse energy, PRF and exposure time are important criteria when considering inactivation of micro-organisms by laser radiation.

  7. High-Power Tunable Laser Pulse Driven Terahertz Generation in Corrugated Plasma Waveguides

    Science.gov (United States)

    Miao, Chenlong; Palastro, John; Antonsen, Thomas

    2016-10-01

    Excitation of terahertz radiation by the interaction of an ultra-short laser pulse and the fields of a miniature, corrugated plasma waveguide is considered. Plasma structures of this type have been realized experimentally and they can support electromagnetic (EM) channel modes with properties that allow for radiation generation. In particular, the mode have subluminal field components, thus allowing phase matching between the generated THz modes and the ponderomotive potential of the laser pulse. Theoretical analysis and full format PIC simulations are conducted. We find THz generated by this slow wave phase matching mechanism is characterized by lateral emission and a coherent, narrow band, tunable spectrum with relatively high power and conversion efficiency. We investigated two different types of channels, and a range of realistic laser pulses and plasma profile parameters are considered with the goal of increasing the conversion of optical energy to THz radiation. We find high laser intensities strongly modify the THz spectrum by exciting higher order channel modes. Enhancement of a specific channel mode can be realized by using an optimum pulse duration and plasma density. As an example, a fixed drive pulse (0.55 J) with spot size of 15 µm and pulse duration of 15 fs excites 37.8 mJ of THz radiation in a 1.5 cm corrugated plasma waveguide with on axis average density of 1.4×1018cm-3, conversion efficiency exceeding 8% is achieved.

  8. Metasurface with Reconfigurable Reflection Phase for High-Power Microwave Applications (Briefing Charts)

    Science.gov (United States)

    2014-06-25

    Antennas Propag., vol. 51, no. 10, pp. 2713–2722, 2003. ∆ℎ1 ∆ℎ2 ∆ℎ Reconfigurable Super Cell Metasurface - Analysis • Linear parametric...Metasurfaces with Reconfigurable Reflection Phase for High-Power Microwave Applications Kenneth L. Morgan, Clinton P. Scarborough, Micah D...TITLE AND SUBTITLE Metasurface with Reconfigurable Reflection Phase for High- Power Microwave Applications 5a. CONTRACT NUMBER 5b

  9. Capacitor performance limitations in high power converter applications

    DEFF Research Database (Denmark)

    El-Khatib, Walid Ziad; Holbøll, Joachim; Rasmussen, Tonny Wederberg

    2013-01-01

    High voltage low inductance capacitors are used in converters as HVDC-links, snubber circuits and sub model (MMC) capacitances. They facilitate the possibility of large peak currents under high frequent or transient voltage applications. On the other hand, using capacitors with larger equivalent...... series inductances include the risk of transient overvoltages, with a negative effect on life time and reliability of the capacitors. These allowable limits of such current and voltage peaks are decided by the ability of the converter components, including the capacitors, to withstand them over...... the expected life time. In this paper results are described from investigations on the electrical environment of these capacitors, including all the conditions they would be exposed to, thereby trying to find the tradeoffs needed to find a suitable capacitor. Different types of capacitors with the same voltage...

  10. High-power ultrafast Yb:fiber laser frequency combs using commercially available components and basic fiber tools

    Science.gov (United States)

    Li, Xinlong; Reber, Melanie A. R.; Corder, Christopher; Chen, Yuning; Zhao, Peng; Allison, Thomas K.

    2016-09-01

    We present a detailed description of the design, construction, and performance of high-power ultrafast Yb:fiber laser frequency combs in operation in our laboratory. We discuss two such laser systems: an 87 MHz, 9 W, 85 fs laser operating at 1060 nm and an 87 MHz, 80 W, 155 fs laser operating at 1035 nm. Both are constructed using low-cost, commercially available components, and can be assembled using only basic tools for cleaving and splicing single-mode fibers. We describe practical methods for achieving and characterizing low-noise single-pulse operation and long-term stability from Yb:fiber oscillators based on nonlinear polarization evolution. Stabilization of the combs using a variety of transducers, including a new method for tuning the carrier-envelope offset frequency, is discussed. High average power is achieved through chirped-pulse amplification in simple fiber amplifiers based on double-clad photonic crystal fibers. We describe the use of these combs in several applications, including ultrasensitive femtosecond time-resolved spectroscopy and cavity-enhanced high-order harmonic generation.

  11. High-power ultrafast Yb:fiber laser frequency combs using commercially available components and basic fiber tools

    CERN Document Server

    Li, X L; Corder, C; Chen, Y; Zhao, P; Allison, T K

    2016-01-01

    We present a detailed description of the design, construction, and performance of high-power ultrafast Yb:fiber laser frequency combs in operation in our laboratory. We discuss two such laser systems: an 87 MHz, 9 W, 85 fs laser operating at 1060 nm and an 87 MHz, 80 W, 155 fs laser operating at 1035 nm. Both are constructed using low-cost, commercially available components, and can be assembled using only basic tools for cleaving and splicing single-mode fibers. We describe practical methods for achieving and characterizing low-noise single-pulse operation and long-term stability from Yb:fiber oscillators based on nonlinear polarization evolution. Stabilization of the combs using a variety of transducers, including a new method for tuning the carrier-envelope offset frequency, is discussed. High average power is achieved through chirped-pulse amplification in simple fiber amplifiers based on double-clad photonic crystal fibers. We describe the use of these combs in several applications, including ultrasensit...

  12. Use of dominant harmonic active filters in high power applications

    Science.gov (United States)

    Cheng, Po-Tai

    The application of power electronics equipment is increasing rapidly. It is estimated that 60% of electrical power will be processed by power electronics equipment by year 2000. These equipments typically require rectifiers for AC-DC power conversion. Due to their nonlinear nature, most rectifiers draw harmonic current from the utility grid. The harmonic current causes higher energy losses, and may excite resonance conditions in the utility grid. Harmonic standards such as IEEE 519 and IEC 1000-3-2 have been proposed to regulate the harmonic current and voltage levels. This work is to develop a dominant harmonic active filter (DHAF) to realize a cost-effective active filtering solution for nonlinear loads in the range of megawatt and above. The DHAF system achieves harmonic isolation at dominant harmonic frequencies, e.g. the 5th and 7th. This approach allows use of low switching frequency and small rating active filter inverters (1%--2% of the load MVA rating) for implementation. Review of conventional passive filters and various active filters based on high bandwidth PWM inverters is provided. The control theory of the DHAF system is presented. Comparison of the DHAF system and other dominant harmonic filtering approach is provided. Simulation results and laboratory prototype test results are presented to validate the effectiveness of the proposed DHAF system.

  13. Shannon entropy method of small-scale self-focusing assessment in high-power laser systems.

    Science.gov (United States)

    Liu, Rende; Hu, Dongxia; Deng, Xuewei; Zhao, Junpu; Wang, Wenyi; Dai, Wanjun; Zhou, Wei; Huang, Xiaoxia; Li, Min; Yang, Sheng

    2016-02-01

    Through analysis of near-field beam profiles, we propose a method using Shannon entropy to assess the development of small-scale self-focusing during laser propagation and amplification in high-power laser systems. In this method, the entropy curve that corresponds to increasing B integral displays an evident turning point at which small-scale self-focusing starts to rapidly develop. In contrast to classical methods using contrast, modulation, or power spectral density, the proposed method provides the B integral criterion more clearly and objectively. This approach is an optimization method that can be utilized in the design and operation of high-power laser systems.

  14. Monolithic micro-laser with KTP ridge waveguides for injection seeding high power lasers Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This NASA Small Business Innovation Research Phase I project will develop a technique to greatly improve the direct coupling of a diode laser to an optical waveguide...

  15. Short Range Photoassociation of Rb2 by a high power fiber laser

    Science.gov (United States)

    Passagem, Henry; Rodriguez, Ricardo; Ventura, Paulo; Bouloufa, Nadia; Dulieu, Olivier; Marcassa, Luis

    2016-05-01

    Photoassociation has been studied using cold trapped atomic samples for the last 20 years. Due to poor Franck-Condon overlap, a free-to-bound transition followed by spontaneous decay results in a small production of electronic ground state molecules. If the photoassociation is done at short range, deeply bound ground state molecules can be formed. Optical pumping schemes can be used to populate a single state. In our experiment, we have performed trap loss spectroscopy on trapped 85 Rb atoms in a MOT using a high power fiber laser. Our single mode fiber laser (linewidth < 1 MHz) produces about 50 W, which can be tuned in the 1060-1070 nm range. Two vibrational bound states of the 0u+ potential were observed (ν = 137 and 138). The frequency positions as well as the rotational constants of these states are in good agreement with theoretical predictions. We have also measured the lifetime of a crossed optical dipole trap using such fiber laser. The lifetime on resonance is shorter than off resonance as expected. A simple theoretical model indicates that the molecules decay to deeply bound vibrational levels in the ground state. This work was supported by Fapesp and INCT-IQ.

  16. Efficiency of frequency conversion of high power laser and KDP crystal clamping method

    Science.gov (United States)

    Yan, Han; Du, Weifeng; Pei, Guoqing; Qin, Tinghai; Ye, Lang; Xu, Xu

    2017-05-01

    In the high power solid laser driver, the frequency conversion unit is of strict requirement to meet the drive condition of ICF. The performance of large caliber KDP crystal, which is the core of frequency conversion of laser, is a vital aspect affecting the overall technical index of the laser driver. In order to get a higher efficiency of frequency conversion, KDP crystal must keep a better surface condition, which asks for high-quality assemblage and adjustment. The current method used in engineering has insufficient knowledge and recognition on surface deformation control of the crystal. Meanwhile, the method itself is of low efficiency on clamping, and lacks of protection for the crystal. Thus, in this article an investigation of crystal clamping method with lower force was performed, factors affecting the surface of crystal were explored, through both imitation and experiment. The clamping method was redesigned and the frequency conversion efficiency was tested. Meanwhile, with the new method, clamping efficiency increases, the optical performance of crystals improves, and the crystals get better protection.

  17. Thermo-optical properties of beryllium containing oxide crystals as materials for high power laser systems

    Science.gov (United States)

    Pestryakov, E. V.; Petrov, V. V.; Trunov, V. I.; Kirpichnikov, A. V.; Laptev, A. V.; Matrosov, V. N.

    2007-06-01

    The elastic and thermo-optical properties of chrysoberyl, beryllium hexaaluminate and beryllium-lanthanum hexaaluminate crystals have been experimentally studied. The velocities of elastic-wave propagation in the crystals are measured by acousto-optic interference method. The values of all the independent components of elastic-constant tensor are determined and used to calculate a number of important dynamic parameters of the crystals such as the Young's and shear moduli, the modulus of volume elasticity, Poisson's ratio, the Debye temperature. Also measurements of refractive indices in 25 - 75 C temperature range in VIS spectral region were performed. Using experimental data the dispersion of thermal optical coefficients (dn/dT) was calculated, these data were employed to evaluate the thermal lens in beryllium containing laser crystals. The experimental and calculated data are compared with similar parameters for well-known laser hosts. Some of beryllium containing oxide crystals was shown to be candidates for master oscillator and amplifying stages of high power femtosecond laser systems.

  18. High-power laser shock-induced dynamic fracture of aluminum and microscopic observation of samples

    Directory of Open Access Journals (Sweden)

    Fan Zhang

    2015-01-01

    Full Text Available High-power laser induced shocks generated by “ShenGuang II” laser facility has been used to study spall fracture of polycrystalline aluminum at strain rates more than 106/s. The free surface velocity histories of shock-loaded samples, 150 μm thick and with initial temperature from 293 K to 873 K, have been recorded using velocity interferometer system for any reflector (VISAR. From the free surface velocity profile, spall strength and yield stress are calculated, it demonstrates that spall strength will decline and yield strength increase with initial temperature. The loaded samples are recovered to obtain samples' section and free surface metallographic pictures through Laser Scanning Confocal Microscopy. It is found that there are more micro-voids and more opportunity to appear bigger voids near the spall plane and the grain size increases with temperature slowly but smoothly except the sharply change at 893 K (near melting point. Besides, the fracture mechanisms change from mainly intergranular fracture to transgranular fracture with the increase of initial temperature.

  19. Setup of a beam control system for high power laser system at DLR

    Science.gov (United States)

    Buske, Ivo; Walther, Andreas

    2016-10-01

    Different types of high power or high energy lasers in the multi kW class are currently available or are under development with promising progress reports. A major challenge is to deliver as much as possible of the available power onto a small and fast moving target over a long distance through a disturbing atmosphere. High resolution imaging is a common way to identify the category of targets dedication and to determine the spatial position relative to the observer. By illuminating the target with a laser the imaging system becomes more resilient towards ambient light and the exposure time can be reduced drastically. Fast and deterministic control loops are demanding for the moving parts in order to maintain a high accuracy for the pointing of the turret and aiming of the laser countermeasure system. Here, we report on the progress of such a beam control system developed at the Institute of Technical Physics of DLR. In an overview we present the beam control system and explain different sub-systems. Performance tests were taken at our test. At a distance we simulated various scenarios for probing the limits of the tracking and pointing accuracy with a target on a fast moving linear stage. We present first results of the beam control system performance.

  20. Machining parameter optimization of C/SiC composites using high power picosecond laser

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Ruoheng; Li, Weinan [State Key Laboratory of Transient Optics and Photonics, Xi’an Institute of Optics and Precision Mechanics, Chinese Academy of Sciences, Xi’an, Shaanxi 10068 (China); Liu, Yongsheng, E-mail: yongshengliu@nwpu.edu.cn [Science and Technology on Thermostructure Composite Materials Laboratory, Northwestern Polytechnical University, Xi’an, Shaannxi 710072 (China); Wang, Chunhui; Wang, Jing [Science and Technology on Thermostructure Composite Materials Laboratory, Northwestern Polytechnical University, Xi’an, Shaannxi 710072 (China); Yang, Xiaojun [State Key Laboratory of Transient Optics and Photonics, Xi’an Institute of Optics and Precision Mechanics, Chinese Academy of Sciences, Xi’an, Shaanxi 10068 (China); Cheng, Laifei, E-mail: liuys99067@163.com [Science and Technology on Thermostructure Composite Materials Laboratory, Northwestern Polytechnical University, Xi’an, Shaannxi 710072 (China)

    2015-03-01

    Highlights: • We found that the helical line width and the helical line spacing, machining time and the scanning speed on the surface morphology of machined holes had remarkable effects on the qualities of micro-holes such as shape and depth. • The debris consisted of C, Si and O was observed on the machined surface. The Si−C bonds of the SiC matrix transformed into Si−O bonds after machined. - Abstract: Picosecond laser is an important machining technology for high hardness materials. In this paper, high power picosecond laser was utilized to drill micro-holes in C/SiC composites, and the effects of different processing parameters including the helical line width and spacing, machining time and scanning speed were discussed. To characterize the qualities of machined holes, scanning electron microscope (SEM) was used to analyze the surface morphology, energy dispersive spectroscopy (EDS) and X-ray photoelectric spectroscopy (XPS) were employed to describe the element composition change between the untreated and laser-treated area. The experimental results indicated that all parameters mentioned above had remarkable effects on the qualities of micro-holes such as shape and depth. Additionally, the debris consisted of C, Si and O was observed on the machined surface. The Si−C bonds of the SiC matrix transformed into Si−O bonds after machined. Furthermore, the physical process responsible for the mechanism of debris formation was discussed as well.

  1. Machining parameter optimization of C/SiC composites using high power picosecond laser

    Science.gov (United States)

    Zhang, Ruoheng; Li, Weinan; Liu, Yongsheng; Wang, Chunhui; Wang, Jing; Yang, Xiaojun; Cheng, Laifei

    2015-03-01

    Picosecond laser is an important machining technology for high hardness materials. In this paper, high power picosecond laser was utilized to drill micro-holes in C/SiC composites, and the effects of different processing parameters including the helical line width and spacing, machining time and scanning speed were discussed. To characterize the qualities of machined holes, scanning electron microscope (SEM) was used to analyze the surface morphology, energy dispersive spectroscopy (EDS) and X-ray photoelectric spectroscopy (XPS) were employed to describe the element composition change between the untreated and laser-treated area. The experimental results indicated that all parameters mentioned above had remarkable effects on the qualities of micro-holes such as shape and depth. Additionally, the debris consisted of C, Si and O was observed on the machined surface. The Sisbnd C bonds of the SiC matrix transformed into Sisbnd O bonds after machined. Furthermore, the physical process responsible for the mechanism of debris formation was discussed as well.

  2. Effect of antireflection facet coatings on the characteristics of a high-power red laser diode

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Chang Zoo; Choi, Je Hyuk; Shin, Chan Soo [Korea Advanced Nano Fab Center, Suwon (Korea, Republic of); Kim, Ho Gyoung [Seoul National University of Science and Technology, Seoul (Korea, Republic of)

    2014-05-15

    We investigated the effect of antireflection (AR) coatings on the performance of high-power red laser diodes (LDs). The AR coating at the front facet and the high reflection (HR) coating at the rear facet were deposited on cleaved facets. As an AR coating, SiO{sub 2} or Si{sub 3}N{sub 4} single layers with different thicknesses were employed. When the reflectivity of the AR coating was 25%, the best LD performance was obtained. The fitting to the threshold current density vs. effective optical length plot produced a transparent current density of 310 A/cm{sup 2}. Under continuous wave (cw) operation at 15 .deg. C, the operating current was 1.41 A, and the operating voltage was 2.33 V with an optical output of 280 mW. At an operating temperature of 0 .deg. C, we observed the maximum output power of about 390 mW.

  3. Numerical study on mirror of high power laser with heatpipe cooling

    Science.gov (United States)

    Chen, Jiayuan, II; Zhu, Haihong; Cheng, Zuhai

    2008-12-01

    Mirror surface of high power laser would be deformed by the pressure of the coolant in a liquid cooling mirror system. In order to eliminate the impact of pressure and vibration of cooling water to the stability of the output beam, a cooling mirror with heatpipe is designed. With the same structure and conditions, solid mirror, water cooling mirror and heat pipe cooling mirror are simulated by ANSYS program. The time-varying thermal deformations of the group mirrors after 60s under the net heat absorption of 12W/cm2 are obtained. The maximal peak and valley difference value of mirror surface deformation of solid mirror along Z-axis, water cooling mirror and heat pipe cooling mirror after 60s is 1.33μm, 0.845 μm and 0.1094 μm respectively.

  4. An improved method for stripping cladding light in high power fiber lasers

    Science.gov (United States)

    Li, Tenglong; Wu, Juan; Sun, Yinghong; Wang, Yanshan; Ma, Yi

    2015-02-01

    In order to ensure the high power all-fiber laser reliability and excellent beam quality, it is necessary to strip the unwanted cladding light. The common method for stripping cladding light is to recoat the double cladding fiber with a high index gel, but localized heating and low thermal conductivity of the recoating gel are the prime factors limiting the power-handling capability of the cladding power stripper(CPS). An improved fabrication technique to manufacture the CPS is presented. Light stripping section of the fiber is fused with a transparent quartz tube, by applying different amount of etchant along the quartz tube, frosted surface is created and uniformly removal of the cladding light is achieved. The quartz tube is joined to water-cooled thermal enclosure tightly without the gel to avoid heat aggregation. The power-handling capability of the device is tested under 200W of cladding light, and attenuation of 20 dB is achieved.

  5. Stimulated Raman Scattering and Nonlinear Focusing of High-Power Laser Beams Propagating in Water

    CERN Document Server

    Hafizi, B; Penano, J R; Gordon, D F; Jones, T G; Helle, M H; Kaganovich, D

    2015-01-01

    The physical processes associated with propagation of a high-power (power > critical power for self-focusing) laser beam in water include nonlinear focusing, stimulated Raman scattering (SRS), optical breakdown and plasma formation. The interplay between nonlinear focusing and SRS is analyzed for cases where a significant portion of the pump power is channeled into the Stokes wave. Propagation simulations and an analytical model demonstrate that the Stokes wave can re-focus the pump wave after the power in the latter falls below the critical power. It is shown that this novel focusing mechanism is distinct from cross-phase focusing. While discussed here in the context of propagation in water, the gain-focusing phenomenon is general to any medium supporting nonlinear focusing and stimulated forward Raman scattering.

  6. Ignition studies in support of the European High Power Laser Energy Research Facility project

    Indian Academy of Sciences (India)

    J Pasley

    2010-11-01

    The European High Power Laser Energy Research Facility (HiPER) project is one of a number of large-scale scientific infrastructure projects supported by the European Commission’s Seventh Framework Programme (FP7). Part of this project involves the development of a target area for the exploration of inertial fusion energy. This paper describes some of the research that is being carried out by the author in support of this aspect of the program. The effects of different regions of the fusion target mixing prior to thermonuclear ignition have been investigated using the 1D Lagrangian radiation hydrodynamics simulation code HYADES. Results suggest that even low (few parts per million) levels of contamination of fuel by high- ion species may inhibit ignition due to radiative cooling of the ignition spot.

  7. Research of new packaging and cooling technique for high power fiber laser used pump coupler

    Science.gov (United States)

    Mu, Wei; Si, Xu; Lin, Ya-jun; Xu, Cheng-lin; Ma, Yun-liang; Xiao, Chun

    2015-10-01

    This article analyzes the advantages and disadvantages of a packaging structure for pump coupler, where common heat conduction material is used. In this study, the possibility of using new technology of thermal conductivity is discussed. We also proposes a solution that make the function and effect of package more uniform. A serial of experiments are done for research the cooling effect and the working reliability of the fiber combiners and couplers. Experiment proves that after improved method of package, the cooling speed increases significantly comparing the sample with old type of package technique. The technique discussed in this paper will make the high power fiber laser working long time with steady power output and high efficiency.

  8. High power, low divergent, substrate emitting quantum cascade ring laser in continuous wave operation

    Directory of Open Access Journals (Sweden)

    D. H. Wu

    2017-03-01

    Full Text Available We demonstrate a surface grating coupled substrate emitting quantum cascade ring laser with high power room temperature continuous wave operation at 4.64 μm. A second order surface metal/semiconductor distributed-feedback grating is used for in-plane feedback and vertical out-coupling. A device with 400 μm radius ring cavity exhibits an output power of 202 mW in room temperature continuous wave operation. Single mode operation with a side mode suppression ratio of 25 dB is obtained along with a good linear tuning with temperature. The far field measurement exhibits a low divergent concentric ring beam pattern with a lobe separation of ∼0.34°, which indicates that the device operates in fundamental mode (n = 1.

  9. CO2 laser-fabricated cladding light strippers for high-power fiber lasers and amplifiers.

    Science.gov (United States)

    Boyd, Keiron; Simakov, Nikita; Hemming, Alexander; Daniel, Jae; Swain, Robert; Mies, Eric; Rees, Simon; Andrew Clarkson, W; Haub, John

    2016-04-10

    We present and characterize a simple CO2 laser processing technique for the fabrication of compact all-glass optical fiber cladding light strippers. We investigate the cladding light loss as a function of radiation angle of incidence and demonstrate devices in a 400 μm diameter fiber with cladding losses of greater than 20 dB for a 7 cm device length. The core losses are also measured giving a loss of cladding light stripping of a 300 W laser diode with minimal heating of the fiber coating and packaging adhesives.

  10. High beam quality and high power CO II lasers for technologies and medicine

    Science.gov (United States)

    Vasiltsov, V. V.; Berishvili, I. I.; Galushkin, M. G.; Golubev, V. S.; Panchenko, V. Ya.; Ulyanov, V. A.; Zinina, N. N.; Vakhromeeva, M. N.; Vakhrameeva, A. Y.

    2007-06-01

    The technical characteristics of the new three models of diffusion-cooled multichannel waveguide industrial CO II lasers excited with acoustic-frequency ac discharge are presented. The industrial lasers of this type have been developed for years at ILIT RAS. Generation of low (to 400 W) average power proved to be technically realizable through air cooling of the oscillator, which makes the laser performance even more attractive. The above lasers can be used to advantage in the laser processing systems intended for precision cutting of metallic (thickness to 10 mm) and non-metallic (thickness to 40 mm) materials; welding; surfacing and fabrication of parts from composite and metallic powder materials. The paper also provides the description and the technical characteristics of intellectual medical cardio-surgery laser systems of "Perfocor" family, developed at ILIT RAS for the transmyocardial laser revascularization (TMLR) which presents a promising method to cure the ischemic disease of heart. The clinical results (more than 800 operations) are presented. Owing to application of the TMLR technique the death rate at the A.N. Bakoulev Center is the lowest in the world. The project of a new CO II laser surgery plant "Khirurg" is discussed that would deliver up to 200 W power and is based on the model TL-300 with a system of biotissue diagnostics.

  11. Measurement of electromagnetic pulses generated during interactions of high power lasers with solid targets

    Science.gov (United States)

    De Marco, M.; Krása, J.; Cikhardt, J.; Pfeifer, M.; Krouský, E.; Margarone, D.; Ahmed, H.; Borghesi, M.; Kar, S.; Giuffrida, L.; Vrana, R.; Velyhan, A.; Limpouch, J.; Korn, G.; Weber, S.; Velardi, L.; Delle Side, D.; Nassisi, V.; Ullschmied, J.

    2016-06-01

    A target irradiated with a high power laser pulse, blows off a large amount of charge and as a consequence the target itself becomes a generator of electromagnetic pulses (EMP) owing to high return current flowing to the ground through the target holder. The first measurement of the magnetic field induced by the neutralizing current reaching a value of a few kA was performed with the use of an inductive target probe at the PALS Laser Facility (Cikhardt et al. Rev. Sci. Instrum. 85 (2014) 103507). A full description of EMP generation should contain information on the spatial distribution and temporal variation of the electromagnetic field inside and outside of the interaction chamber. For this reason, we consider the interaction chamber as a resonant cavity in which different modes of EMP oscillate for hundreds of nanoseconds, until the EMP is transmitted outside through the glass windows and EM waves are attenuated. Since the experimental determination of the electromagnetic field distribution is limited by the number of employed antennas, a mapping of the electromagnetic field has to be integrated with numerical simulations. Thus, this work reports on a detailed numerical mapping of the electromagnetic field inside the interaction chamber at the PALS Laser Facility (covering a frequency spectrum from 100 MHz to 3 GHz) using the commercial code COMSOL Multiphysics 5.2. Moreover we carried out a comparison of the EMP generated in the parallelepiped-like interaction chamber used in the Vulcan Petawatt Laser Facility at the Rutherford Appleton Laboratory, against that produced in the spherical interaction chamber of PALS.

  12. Recent Advances in Room Temperature, High-Power Terahertz Quantum Cascade Laser Sources Based on Difference-Frequency Generation

    Directory of Open Access Journals (Sweden)

    Quanyong Lu

    2016-07-01

    Full Text Available We present the current status of high-performance, compact, THz sources based on intracavity nonlinear frequency generation in mid-infrared quantum cascade lasers. Significant performance improvements of our THz sources in the power and wall plug efficiency are achieved by systematic optimizing the device’s active region, waveguide, and chip bonding strategy. High THz power up to 1.9 mW and 0.014 mW for pulsed mode and continuous wave operations at room temperature are demonstrated, respectively. Even higher power and efficiency are envisioned based on enhancements in outcoupling efficiency and mid-IR performance. Our compact THz device with high power and wide tuning range is highly suitable for imaging, sensing, spectroscopy, medical diagnosis, and many other applications.

  13. Laser surface remelting and hardening of an automotive shaft sing a high-power fiber laser

    Directory of Open Access Journals (Sweden)

    Milton Sergio Fernandes de Lima

    2007-12-01

    Full Text Available An automotive shaft was surface-remelted and hardened using a 2 kW fiber laser and an adapted linear axis whose rotating axis produced helical tracks at 120 RPM. The process variable was the laser power, ranging from 300 to 1100 W, which produced two regions in the material: a martensitic region (MR and a partially transformed region (PTR. The MR is formed after rapid solidification or austenitization followed by rapid cooling (10(7 K.s-1. The PTR is composed of martensite, unchanged pearlite and proeutectoid ferrite. The maximum case depth was about 0.3 mm. The microhardness inside the martensitic regions are at least double that of the base material, i.e. between 800 than 600 HV compared to 300 HV. Thermal simulations using a modified Rosenthal formalism help elucidate the phase transformation inside the material and show good agreement with experimental results. The experimental laser-steel absorptivities were measured; they ranged between 38 and 59% depending on the laser power and the amount of liquid at the surface.

  14. Feasibility study on strengthening heating effect of high power short pulse laser on biological tissue by micro/nano metal particles

    Science.gov (United States)

    Lv, Yonggang; Huai, Xiulan

    2008-10-01

    A new method for enhancing the heating effect of high power short pulse laser on biological tissue by micro/nano metal particles was proposed. Theoretical analysis of the influences of the micro/nano particle kind, the concentration and the microcosmic distribution of micro/nano particles on the temperature response was carried out with a multi-layer hyperbolic heat conduction model with volumetric heat generation. The results indicate that embedding micro/nano particles could improve the surface temperature increase of biological tissue with short duration and reduce the deeper material temperature under the same heating condition, which would help strengthen the heating effects of high power short pulse laser on biological tissue. This study may open a new technical approach for improving laser applications.

  15. Influence of the fiber Bragg gratings with different reflective bandwidths in high power all-fiber laser oscillator

    Science.gov (United States)

    Wang, Jianming; Yan, Dapeng; Xiong, Songsong; Huang, Bao; Li, Cheng

    2017-01-01

    The effects of large-mode-area (LMA) fiber Bragg gratings (FBGs) with different reflective bandwidths on bi-directionally pumped ytterbium-doped single-mode all-fiber laser oscillator have been investigated experimentally. The forward laser output power and the backward signal leakage were measured and analyzed. It was found that the laser output power and efficiency depended on the bandwidth of the high-reflection (HR) FBG used in the laser cavity. The broader bandwidth gives higher laser efficiency, especially at high power level.

  16. Er3+ and Yb3+ Codoped Phosphate Laser Glass for High Power Flashlamp Pumping

    Institute of Scientific and Technical Information of China (English)

    FANG Yong-Zheng; JIN Ming-Lin; WEN Lei; LI Shun-Guang; HU Li-Li

    2007-01-01

    A novel Yb3+-Er3+ codoped phosphate glass for high power flashlamp pumping and high repetition rate laser at 1.54 μm, designated EAT5-2, is developed. The weight-loss rate of is 1.3×10-5 gcm-2h-l in boiling water, which is comparable to Kigre's QX-Er glass. Some spectroscopic parameters are analysed by Judd-Ofelt theory and McCumber theory. The emission cross section is calculated to be 0.73×10-20 cm2. The thermo-mechanical properties of EAT5-2 are modified after an ion-exchange chemical strengthening process in a KNO3/NaNO3 molten salt bath. The thresholds for optical damage from the nashlamp pumping are tested on glass rods. A repetition rate of 15 Hz is achieved for chemically strengthened glass. The laser experimental results at 1.54 μm from nashlamp pumping are also reported.

  17. Active Stabilization of the Beam Pointing of a High- Power KrF Laser System

    Directory of Open Access Journals (Sweden)

    Barna1 A.

    2015-03-01

    Full Text Available An active beam-pointing stabilization system has been developed for a high-power KrF laser system to eliminate the long-term drift of the directional change of the beam in order to have a stable focusing to a high intensity. The control of the beam direction was achieved by a motor-driven mirror activated by an electric signal obtained by monitoring the position of the focus of the output beam. Instead of large sized UV-sensitive position sensitive detectors a simple arrangement with scatter plates and photodiodes are used to measure the directionality of the beam. After the beam stabilization the long-term residual deviation of the laser shots is ~14 μrad, which is comparable to the shot-to-shot variation of the beam (~12 μrad. This deviation is small enough to keep the focal spot size in a micrometer range when tightly focusing the beam using off-axis parabolic mirrors.

  18. Impurity-free quantum well intermixing for large optical cavity high-power laser diode structures

    Science.gov (United States)

    Kahraman, Abdullah; Gür, Emre; Aydınlı, Atilla

    2016-08-01

    We report on the correlation of atomic concentration profiles of diffusing species with the blueshift of the quantum well luminescence from both as-grown and impurity free quantum wells intermixed on actual large optical cavity high power laser diode structures. Because it is critical to suppress catastrophic optical mirror damage, sputtered SiO2 and thermally evaporated SrF2 were used both to enhance and suppress quantum well intermixing, respectively, in these (Al)GaAs large optical cavity structures. A luminescence blueshift of 55 nm (130 meV) was obtained for samples with 400 nm thick sputtered SiO2. These layers were used to generate point defects by annealing the samples at 950 °C for 3 min. The ensuing Ga diffusion observed as a shifting front towards the surface at the interface of the GaAs cap and AlGaAs cladding, as well as Al diffusion into the GaAs cap layer, correlates well with the observed luminescence blue shift, as determined by x-ray photoelectron spectroscopy. Although this technique is well-known, the correlation between the photoluminescence peak blue shift and diffusion of Ga and Al during impurity free quantum well intermixing on actual large optical cavity laser diode structures was demonstrated with both x ray photoelectron and photoluminescence spectroscopy, for the first time.

  19. 67.9  W high-power white supercontinuum all-fiber laser source.

    Science.gov (United States)

    Sun, Chang; Ge, Tingwu; Li, Siyuan; An, Na; Wang, Zhiyong

    2016-05-10

    We present a high-power white supercontinuum (SC) all-fiber laser source with average power of 67.9 W, spectrum ranging from 500 to 1700 nm, and spectral width exceeding 1000 nm for spectrum with flatness below 10 dB (except pump wavelength). Also, the visible waveband power (below 850 nm) occupies about 21% of the total SC power. A 145 W high-power picosecond pulse fiber laser is specially designed with high repetition frequency of 656 MHz to reduce nonlinear effects. Meanwhile, a homemade high-power mode field adaptor that can operate stably at hundreds of watts of pulse power has high coupling efficiency of 82%. To our knowledge, the 67.9 W white SC fiber laser source we achieved is the highest reported with such a wide and flat optical spectrum.

  20. Nonlinear dynamics of high-power ultrashort laser pulses: exaflop computations on a laboratory computer station and subcycle light bullets

    Science.gov (United States)

    Voronin, A. A.; Zheltikov, A. M.

    2016-09-01

    The propagation of high-power ultrashort light pulses involves intricate nonlinear spatio-temporal dynamics where various spectral-temporal field transformation effects are strongly coupled to the beam dynamics, which, in turn, varies from the leading to the trailing edge of the pulse. Analysis of this nonlinear dynamics, accompanied by spatial instabilities, beam breakup into multiple filaments, and unique phenomena leading to the generation of extremely short optical field waveforms, is equivalent in its computational complexity to a simulation of the time evolution of a few billion-dimensional physical system. Such an analysis requires exaflops of computational operations and is usually performed on high-performance supercomputers. Here, we present methods of physical modeling and numerical analysis that allow problems of this class to be solved on a laboratory computer boosted by a cluster of graphic accelerators. Exaflop computations performed with the application of these methods reveal new unique phenomena in the spatio-temporal dynamics of high-power ultrashort laser pulses. We demonstrate that unprecedentedly short light bullets can be generated as a part of that dynamics, providing optical field localization in both space and time through a delicate balance between dispersion and nonlinearity with simultaneous suppression of diffraction-induced beam divergence due to the joint effect of Kerr and ionization nonlinearities.

  1. High power red laser at 671nm by intracavity frequency doubling of a Nd:YVO4 laser

    Institute of Scientific and Technical Information of China (English)

    Yao Ai-Yun; Hou Wei; Li Hui-Qing; Bi Yong; Li Rui-Ning; Geng Ai-Cong; Kong Yu-Peng; Cui Da-Fu; Xu Zu-Yan

    2005-01-01

    This paper reports a high-power quasi-continuous wave (quasi-CW) source of red laser at 671nm obtained by intracavity frequency doubling of a double-end-pumped 1342nm Nd:YVO4 laser, based on the nonlinear crystal LiB3O5 (LBO)The average output power of 2.9W at 671nm was obtained at the incident pump power of 19.5W. The overall optical to optical efficiency is 14.9%. We have analyzed the influence of the optimal pump size, the optimal focal position and the reduction of the thermal effect on high output. The combination of double-end-pumping and the quasi-CW performance greatly reduces the thermal effect.

  2. Suppressing the preferential σ-polarization oscillation in a high power Nd∶YVO4 laser with wedge laser crystal

    Institute of Scientific and Technical Information of China (English)

    Zheng Yao-Hui; Zhou Hai-Jun; Wang Ya-Jun; Wu Zhi-Qiang

    2013-01-01

    We observe the phenomenon of priority oscillation of the unexpected σ-polarization in high-power Nd∶YVO4 ring laser.The severe thermal lens of the σ-polarized lasing,compared with the π-polarized lasing,is the only reason for the phenomenon.By designing a wedge Nd∶YVO4 crystal as the gain medium,the unexpected σ-polarization is completely suppressed in the entire range of pump powers,and the polarization stability of the expected π-polarized output is enhanced.With the output power increasing from threshold to the maximum power,no σ-polarization lasing is observed.As a result,25.3 W of stable single-frequency laser output at 532 nm is experimentally demonstrated.

  3. High power CO2 laser development with AOM integration for ultra high-speed pulses

    Science.gov (United States)

    Bohrer, Markus; Vaupel, Matthias; Nirnberger, Robert; Weinberger, Bernhard; Jamalieh, Murad

    2017-01-01

    There is a 500 billion USD world market for packaging expected to grow to a trillion in 2030. Austria plays an important role world wide for high speed laser engraving applications — especially when it comes to high end solutions. Such high end solutions are fundamental for the production of print forms for the packaging and decorating industry (e. g. cans). They are additionally used for security applications (e. g. for printing banknotes), for the textile printing industry and for creating embossing forms (e. g. for the production of dashboards in the automotive industry). High speed, high precision laser engraving needs laser resonators with very stable laser beams (400 - 800W) especially in combination with AOMs. Based upon a unique carbon fiber structure - stable within the sub-micrometer range - a new resonator has been developed, accompanied by most recent thermo-mechanical FEM calculations. The resulting beam is evaluated on an automated optical bench using hexapods, allowing to optimize the complete beam path with collimators and AOM. The major steps related to laser engraving of dry offset printing plates during the full workflow from the artists design to the printed result on an aluminum can is presented in this paper as well as laser characteristics, AOM integration and correlative CLSM and SEM investigation of the results.

  4. JPRS Report, Science & Technology, China, High-Power Lasers & Laser Fusion Research

    Science.gov (United States)

    1991-10-18

    pcvx [Article by Sun Kexi [1327 0668 3556], Xu Heping [1776 0735 1627], Tang Yongjiang [0781 3075 0256], Zheng Zhijian [6774 1807 1017], and Yang...October 1991 targets. This indicates that Hohlraum targets have a The authors wish to thank Zheng Zhijian [6774 1807 relatively abundant amount of dilute...Guanlong [7806 7070 7893], Dai Dazhi [2071 6671 2535], Wu Fengchun [0702 The amplified spontaneous emission (ASE) of a laser 6646 2504], and Cai Xijie

  5. Lasers '92; Proceedings of the International Conference on Lasers and Applications, 15th, Houston, TX, Dec. 7-10, 1992

    Science.gov (United States)

    Wang, Charles P. (Editor)

    1993-01-01

    Papers from the conference are presented, and the topics covered include the following: x-ray lasers, excimer lasers, chemical lasers, high power lasers, blue-green lasers, dye lasers, solid state lasers, semiconductor lasers, gas and discharge lasers, carbon dioxide lasers, ultrafast phenomena, nonlinear optics, quantum optics, dynamic gratings and wave mixing, laser radar, lasers in medicine, optical filters and laser communication, optical techniques and instruments, laser material interaction, and industrial and manufacturing applications.

  6. A high power lamp-pumped LNA laser with thermally tuned etalon

    Science.gov (United States)

    Aminoff, C. G.; Essabaa, S.; Brissaud, I.; Arianer, J.

    1991-11-01

    This report describes arc-lamp pumped, tunable, continuous-wave LNA laser with improved output efficiency, suitable for optical pumping of helium. Using thermal tuning of intracavity etalons instead of angle tuning reduces losses caused by walk-off effects and provides continuous frequency scanning without a significant decrease in laser power. We obtain an output power of 4 W in a linewidth of 2.5 GHz with the laser wavelength tuned to the 1.083 μm absorption line of metastable helium. This result represents a fourfold gain in efficiency compared with conventional tuning by tilting. The laser provides efficient polarization of helium by optical pumping in various applications, such as nuclear spin polarization of 3He and spin-polarized electron sources.

  7. Proton acceleration experiments and warm dense matter research using high power lasers

    Energy Technology Data Exchange (ETDEWEB)

    Roth, M; Alber, I; Guenther, M; Harres, K [Institut fuer Kernphysik, Technische Universitaet Darmstadt, 64289 Darmstadt (Germany); Bagnoud, V [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, 64291 Darmstadt (Germany); Brown, C R D [Plasma Physics Group, Imperial College London, SW7 2BZ (United Kingdom); Clarke, R; Heathcote, R; Li, B [STFC, Rutherford Appleton Laboratory (RAL), Chilton, Didcot, OX14 OQX (United Kingdom); Daido, H [Photo Medical Research Center, JAEA, Kizugawa-City, Kyoto 619-0215 (Japan); Fernandez, J; Flippo, K; Gaillard, S; Gauthier, C [Los Alamos National Laboratory (LANL), Los Alamos, NM 87545 (United States); Geissel, M [Sandia National Laboratories, Albuquerque, NM 87185 (United States); Glenzer, S; Kritcher, A; Kugland, N; LePape, S [Lawrence Livermore National Laboratory, Livermore, CA 94551 (United States); Gregori, G, E-mail: markus.roth@physik.tu-darmstadt.d [Clarendon Laboratory, University of Oxford, Parks Road, Oxford OX1 3PU (United Kingdom)

    2009-12-15

    The acceleration of intense proton and ion beams by ultra-intense lasers has matured to a point where applications in basic research and technology are being developed. Crucial for harvesting the unmatched beam parameters driven by the relativistic electron sheath is the precise control of the beam. In this paper we report on recent experiments using the PHELIX laser at GSI, the VULCAN laser at RAL and the TRIDENT laser at LANL to control and use laser accelerated proton beams for applications in high energy density research. We demonstrate efficient collimation of the proton beam using high field pulsed solenoid magnets, a prerequisite to capture and transport the beam for applications. Furthermore, we report on two campaigns to use intense, short proton bunches to isochorically heat solid targets up to the warm dense matter state. The temporal profile of the proton beam allows for rapid heating of the target, much faster than the hydrodynamic response time thereby creating a strongly coupled plasma at solid density. The target parameters are then probed by x-ray Thomson scattering to reveal the density and temperature of the heated volume. This combination of two powerful techniques developed during the past few years allows for the generation and investigation of macroscopic samples of matter in states present in giant planets or the interior of the earth.

  8. High-power monolithic single-mode diode lasers employing active photonic lattices

    Science.gov (United States)

    Botez, Dan

    2003-06-01

    Photonic-lattice structures with modulated gain, that is active photonic lattices (APLs), of large index steps and gain preferentially enhanced on the low-index lattice sites have been used, as early as 1988, for effective lateral-mode control range in large-aperture (100-200 microns) high-power coherent devices. Photonic-bandpass (PBP) structures relying on long-range resonant leaky-wave coupling, so called ROW arrays, have allowed stable, near-diffraction-limited beam operation to powers as high as 1.6W CW and 10W peak pulsed. Photonic-bandgap (PBG) structures with a built-in lattice defect, so called ARROW lasers, have provided up to 0.5W peak-pulsed stable, single-mode power and hold the potential for 1W CW reliable single-mode operation from apertures 8-10 microns wide. The solution for high-efficiency surface emission, from 2nd-order DFB/DBR lasers, in an orthonormal, single-lobe beam pattern was found in 2000. Recently, single-lobe and single-mode operation in a diffraction-limited beam orthonormal to the chip surface was demonstrated from 1.5mm-long DFB/DBR ridge-guide lasers. That opens the way for the realization of 2-D surface-emitting,2nd-order APLs for the stable generation of watts of CW single-lobe, single-mode power from large 2-D apertures, as well as scalability of such devices at the wafer level.

  9. High-power, surface-emitting quantum cascade laser operating in a symmetric grating mode

    Energy Technology Data Exchange (ETDEWEB)

    Boyle, C.; Sigler, C.; Kirch, J. D.; Botez, D.; Mawst, L. J., E-mail: mawst@engr.wisc.edu [Department of Electrical and Computer Engineering, University of Wisconsin-Madison, Madison, Wisconsin 53706 (United States); Lindberg, D. F.; Earles, T. [Intraband, LLC, Madison, Wisconsin 53726 (United States)

    2016-03-21

    Grating-coupled surface-emitting (GCSE) lasers generally operate with a double-lobed far-field beam pattern along the cavity-length direction, which is a result of lasing being favored in the antisymmetric grating mode. We experimentally demonstrate a GCSE quantum-cascade laser design allowing high-power, nearly single-lobed surface emission parallel to the longitudinal cavity. A 2nd-order Au-semiconductor distributed-feedback (DFB)/distributed-Bragg-reflector (DBR) grating is used for feedback and out-coupling. The DFB and DBR grating regions are 2.55 mm- and 1.28 mm-long, respectively, for a total grating length of 5.1 mm. The lasers are designed to operate in a symmetric (longitudinal) grating mode by causing resonant coupling of the guided optical mode to the antisymmetric surface-plasmon modes of the 2nd-order metal/semiconductor grating. Then, the antisymmetric modes are strongly absorbed by the metal in the grating, causing the symmetric mode to be favored to lase, which, in turn, produces a single-lobed beam over a range of grating duty-cycle values of 36%–41%. Simulations indicate that the symmetric mode is always favored to lase, independent of the random phase of reflections from the device's cleaved ends. Peak pulsed output powers of ∼0.4 W were measured with nearly single-lobe beam-pattern (in the longitudinal direction), single-spatial-mode operation near 4.75 μm wavelength. Far-field measurements confirm a diffraction-limited beam pattern, in agreement with simulations, for a source-to-detector separation of 2 m.

  10. Magnetic nanoparticles for biophysical applications synthesized by high-power physical dispersion

    Energy Technology Data Exchange (ETDEWEB)

    Safronov, A.P., E-mail: safronov@iep.uran.ru [Ural Federal University, Yekaterinburg (Russian Federation); Beketov, I.V. [Ural Federal University, Yekaterinburg (Russian Federation); Institute of Elecrophysics, Ural branch of RAS, Yekaterinburg (Russian Federation); Tyukova, I.S. [Ural Federal University, Yekaterinburg (Russian Federation); Medvedev, A.I. [Ural Federal University, Yekaterinburg (Russian Federation); Institute of Elecrophysics, Ural branch of RAS, Yekaterinburg (Russian Federation); Samatov, O.M.; Murzakaev, A.M. [Institute of Elecrophysics, Ural branch of RAS, Yekaterinburg (Russian Federation)

    2015-06-01

    The low cost and high output methods of high-power physical dispersion: the electrical explosion of wire and the laser target evaporation were elaborated for the production of iron oxide magnetic nanoparticles (MNPs) with controlled dispersion parameters and highly reproducible functional properties. The synthesized MNPs were spherical in shape with mean diameter 10 nm and lognormal particle size distribution. The phase composition, shape, particle size and functional properties of MNPs were cross-examined by a variety of contemporary experimental techniques. The phase structure of MNPs corresponds to the inverse spinel of magnetite. Meanwhile, due to the non-equilibrium conditions of the dispersion chemical composition of MNPs is close to maghemite—γ-Fe{sub 2}O{sub 3}. Their magnetic properties are reproducible and very close to the single domain superparamagnetic behavior. The stability of the suspensions of these MNPs and their applicability in the biophysical purposes such as magneto-induced heating have been demonstrated. - Highlights: • We present two methods of low-cost and high output production of iron oxide nanoparticles. • We obtained 10 nm spherical maghemite nanoparticles with close to superparamagnetic behavior. • The suspensions of obtained nanoparticles are stable to salt in physiological concentration. • Magneto-induced heating of suspensions fits well with the theoretical predictions.

  11. New technology for the design of advanced ultrasonic transducers for high-power applications.

    Science.gov (United States)

    Parrini, Lorenzo

    2003-06-01

    A new high-frequency ultrasonic transducer for wire bonding has been conceived, designed, prototyped and tested. In the design phase an advanced approach was used and established. The method is based on the two basic principles of modularity and iteration. The transducer is decomposed to its elementary components. For each component an initial design is obtained with finite elements method (FEM) simulations. The simulated ultrasonic modules are then built and characterized experimentally through laser-interferometry measurements and electrical resonance spectra. The comparison of simulation results with experimental data allows the parameters of FEM models to be iteratively adjusted and optimized. The achieved FEM simulations exhibit a remarkably high-predictive potential and allow full control on the vibration behavior of the ultrasonic modules and of the whole transducer. The new transducer is fixed on the wire bonder with a flange whose special geometry was calculated by means of FEM simulations. This flange allows the converter to be attached on the wire bonder not only in longitudinal nodes but also in radial nodes of the ultrasonic field excited in the horn. This leads to a nearly complete decoupling of the transducer to the wire bonder, which has not been previously obtained. The new approach to mount ultrasonic transducers on a welding-device is of major importance not only for wire bonding but also for all high-power ultrasound applications and has been patented.

  12. High-power EUV lithography sources based on gas discharges and laser-produced plasmas

    Science.gov (United States)

    Stamm, Uwe; Ahmad, Imtiaz; Balogh, Istvan; Birner, H.; Bolshukhin, D.; Brudermann, J.; Enke, S.; Flohrer, Frank; G„bel, Kai; G÷tze, S.; Hergenhan, G.; Kleinschmidt, J.'rgen; Kl÷pfel, Diethard; Korobotchko, Vladimir; Ringling, Jens; Schriever, Guido; Tran, C. D.; Ziener, C.

    2003-06-01

    Semiconductor chip manufacturers are expecting to use extreme UV lithography for production in 2009. EUV tools require high power, brilliant light sources at 13.5 nm with collector optics producing 120 W average power at entrance of the illuminator system. Today the power and lifetime of the EUV light source are considered as the most critical issue for EUV lithography. The present paper gives an update of the development status of EUV light sources at XTREME technologies, a joint venture of Lambda Physik AG, Goettingen, and Jenoptik LOS GmbH, Jena, Germany. Results on both laser produced plasma (LPP) and gas discharge produced plasma (GDPP), the two major technologies in EUV sources, are given. The LPP EUV sources use xenon-jet target systems and pulsed lasers with 400 W average power at 10 kHz developed at XTREME technologies. The maximum conversion efficiency form laser power into EUV in-band power is 0.75% into 2π solid angle. With 300 W laser average power at 3300 Hz repetition rate up to 1.5 W EUV radiation is generated at 13.5 nm. After a collector of 5 sr this corresponds to 0.6 W in intermediate focus without spectral purity filter and 0.5 W in intermediate focus with spectral purity filter. The direct generation of the EUV emitting plasma from electrical discharges is much simpler than LPP because the electrical energy has not to be converted into laser radiation before plasma excitation. XTREME technologies' Xenon GDPP EUV sources use the Z-pinch principle with efficient sliding discharge pre-ionization. The plasma pinch size and the available emission angle have been matched to the etendue of the optical system of 2-3 mm2 sr, i.e. no additional etendue related loss reduces the usable EUV power from the source. In continuous operation at 1000 Hz the GDPP sources emit 50W into 2π solid angle are obtained from the Z-pinch sources. Spatial and temporal emission stability of the EUV sources is in the range of a few percent. Debris shields for EUV sources

  13. High power laser energy distribution patterns, apparatus and methods for creating wells

    Science.gov (United States)

    Faircloth, Brian O.; Zediker, Mark S.; Rinzler, Charles C.; Koblick, Yeshaya; Moxley, Joel F.

    2016-03-15

    There is provided a system, apparatus and methods for providing a laser beam to borehole surface in a predetermined and energy deposition profile. The predetermined energy deposition profiles may be uniform or tailored to specific downhole applications. Optic assemblies for obtaining these predetermined energy deposition profiles are further provided.

  14. Methods and apparatus for delivering high power laser energy to a surface

    Energy Technology Data Exchange (ETDEWEB)

    Faircloth, Brian O; Zediker, Mark S; Rinzler, Charles C; Koblick, Yeshaya; Moxley, Joel F

    2013-04-23

    There is provided a system, apparatus and methods for providing a laser beam to borehole surface in a predetermined and energy deposition profile. The predetermined energy deposition profiles may be uniform or tailored to specific downhole applications. Optic assemblies for obtaining these predetermined energy deposition profiles are further provided.

  15. High power laser energy distribution patterns, apparatus and methods for creating wells

    Energy Technology Data Exchange (ETDEWEB)

    Faircloth, Brian O.; Zediker, Mark S.; Rinzler, Charles C.; Koblick, Yeshaya; Moxley, Joel F.

    2016-03-15

    There is provided a system, apparatus and methods for providing a laser beam to borehole surface in a predetermined and energy deposition profile. The predetermined energy deposition profiles may be uniform or tailored to specific downhole applications. Optic assemblies for obtaining these predetermined energy deposition profiles are further provided.

  16. High-power, high-efficiency, high-brightness long-wavelength laser diodes

    Science.gov (United States)

    Patterson, Steve; Crump, Paul; Wang, Jun; Dong, Weimin; Grimshaw, Mike; Zhang, Shiguo; Elim, Sandrio; Das, Suhit; Bougher, Mike; Patterson, Jason; Kuang, Guokui; Bell, Jake; Farmer, Jason; DeVito, Mark

    2006-05-01

    Interest is rapidly growing in solid-state lasers emitting from 1500-nm to 2100-nm with applications in eye-safe range finding, LIDAR, infrared countermeasures, medicine, dentistry, and others. Traditionally, these solid-state lasers have been pumped by flash lamps or more recently, by semiconductor diode lasers. In the case of the latter, the diodes of choice have been those emitting below 1-μm. The sub-micron class of semiconductor diode lasers is highly mature and has enjoyed recent rapid advances in power and efficiency. Unfortunately, the quantum defect generated when converting to the desired wavelengths results in large amounts of excess heat generation leading to costly and heavy, expensive cooling systems and performance problems related to thermal lensing. System complexity adds further cost and weight when intermediaries, such as optical parametric oscillators, are required to reach the desired longer wavelengths. Recent advances in laser diodes emitting from 1400-nm to over 1900-nm now enable the near resonant pumping of such solid state media as Er:YAG, Ho:YAG and Cr:ZnSe. Record results in the peak output power and electrical-to-optical conversion efficiency of diode lasers emitting around 1470-nm, 1700-nm and 1900-nm are presented here.

  17. Stimulated Brillouin scattering mirror system, high power laser and laser peening method and system using same

    Science.gov (United States)

    Dane, C. Brent; Hackel, Lloyd; Harris, Fritz B.

    2007-04-24

    A laser system, such as a master oscillator/power amplifier system, comprises a gain medium and a stimulated Brillouin scattering SBS mirror system. The SBS mirror system includes an in situ filtered SBS medium that comprises a compound having a small negative non-linear index of refraction, such as a perfluoro compound. An SBS relay telescope having a telescope focal point includes a baffle at the telescope focal point which blocks off angle beams. A beam splitter is placed between the SBS mirror system and the SBS relay telescope, directing a fraction of the beam to an alternate beam path for an alignment fiducial. The SBS mirror system has a collimated SBS cell and a focused SBS cell. An adjustable attenuator is placed between the collimated SBS cell and the focused SBS cell, by which pulse width of the reflected beam can be adjusted.

  18. Laser sources for lidar applications

    Science.gov (United States)

    Kilmer, J.; Iadevaia, A.; Yin, Y.

    2012-06-01

    Advanced LIDAR applications such as next gen: Micro Pulse; Time of Flight (e.g., Satellite Laser Ranging); Coherent and Incoherent Doppler (e.g., Wind LIDAR); High Spectral Resolution; Differential Absorption (DIAL); photon counting LIDAR (e.g., 3D LIDAR); are placing more demanding requirements on conventional lasers (e.g., increased rep rates, etc.) and have inspired the development of new types of laser sources. Today, solid state lasers are used for wind sensing, 2D laser Radar, 3D scanning and flash LIDAR. In this paper, we report on the development of compact, highly efficient, high power all-solidstate diode pulsed pumped ns lasers, as well as, high average power/high pulse energy sub nanosecond (picosecond (lasers for these next gen LIDAR applications.

  19. Packaged, High-Power, Narrow-Linewidth Slab-Coupled Optical Waveguide External Cavity Laser (SCOWECL)

    Science.gov (United States)

    2010-12-01

    efficiency. With the 20% reflecli vity FBG, the laser ex hibi ts a threshold of 0.9 A and reaches a CW peak power of 0.37 W aI 4 A. The peak effic ...twice the photon energy . The SCOWECL is expected to find applications in free space coherent optical communications and in microwave photollic...Dai , " High effic ient and narrow linewidlh fiber laser based on fiber grat ing Fabry- Perot cavity," Frolltiers of Oploeieclrollics il/ Chinll, vol

  20. Diode Pumped Alkaline Laser System: A High Powered, Low SWaP Directed Energy Option for Ballistic Missile Defense High-Level Summary - April 2017

    Energy Technology Data Exchange (ETDEWEB)

    Wisoff, P. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2017-04-28

    The Diode-Pumped Alkali Laser (DPAL) system is an R&D effort funded by the Missile Defense Agency (MDA) underway at Lawrence Livermore National Laboratory (LLNL). MDA has described the characteristics needed for a Boost Phase directed energy (DE) weapon to work against ICBM-class threat missiles. In terms of the platform, the mission will require a high altitude Unmanned Aerial Vehicle (UAV) that can fly in the “quiet” stratosphere and display long endurance – i.e., days on station. In terms of the laser, MDA needs a high power, low size and weight laser that could be carried by such a platform and deliver lethal energy to an ICBM-class threat missile from hundreds of kilometers away. While both the military and industry are pursuing Directed Energy for tactical applications, MDA’s objectives pose a significantly greater challenge than other current efforts in terms of the power needed from the laser, the low size and weight required, and the range, speed, and size of the threat missiles. To that end, MDA is funding two R&D efforts to assess the feasibility of a high power (MWclass) and low SWaP (size, weight and power) laser: a fiber combining laser (FCL) project at MIT’s Lincoln Laboratory, and LLNL’s Diode-Pumped Alkali Laser (DPAL) system.

  1. High-power electron beam preionized CO/sub 2/ laser modelling. II - Analysis of plasma characteristics

    Energy Technology Data Exchange (ETDEWEB)

    Botti, E. (Napoli, Universita, Naples, Italy); Martellucci, S. (Parma, Universita, Parma, Italy)

    1982-05-11

    In this paper the results of a theoretical analysis on the properties of electric discharges used in high-power molecular lasers are presented. The mathematical model is based on continuity and transport equations for electrons and ions and on the equations concerning the electric field. The model is used both for self-sustained and for non-self-sustained discharges operating in conditions as usually attained in high-power lasers. Spatial profiles of the electrical parameters near the electrodes and in the plasma area are assessed. Current-voltage characteristics are finally derived for a He:N/sub 2/:CO/sub 2/:CO laser mixture. A future work will be devoted both to the kinetic and to the fluid-dynamic model of the laser and to a comparison of the numerical results obtained with available experimental data.

  2. Spectral diagnostics of a vapor-plasma plume produced during welding with a high-power ytterbium fiber laser

    Science.gov (United States)

    Uspenskiy, S. A.; Shcheglov, P. Yu.; Petrovskiy, V. N.; Gumenyuk, A. V.; Rethmeier, M.

    2013-07-01

    We have conducted spectroscopic studies of the welding plasma formed in the process of welding with an ytterbium fiber laser delivering output power of up to 20 kW. The influence of shielding gases (Ar, He) on different parts of the welding plume is investigated. The absorption coefficient of the laser radiation by the welding-plume plasma is estimated. Scattering of 532-nm probe radiation from particles of the condensed metal vapor within the caustic of a high-power fiber laser beam is measured. Based on the obtained results, conclusions are made on the influence of the plasma formation and metal vapor condensation on the radiation of the high-power fiber laser and the stability of the welding process.

  3. Robust modeling and performance analysis of high-power diode side-pumped solid-state laser systems.

    Science.gov (United States)

    Kashef, Tamer; Ghoniemy, Samy; Mokhtar, Ayman

    2015-12-20

    In this paper, we present an enhanced high-power extrinsic diode side-pumped solid-state laser (DPSSL) model to accurately predict the dynamic operations and pump distribution under different practical conditions. We introduce a new implementation technique for the proposed model that provides a compelling incentive for the performance assessment and enhancement of high-power diode side-pumped Nd:YAG lasers using cooperative agents and by relying on the MATLAB, GLAD, and Zemax ray tracing software packages. A large-signal laser model that includes thermal effects and a modified laser gain formulation and incorporates the geometrical pump distribution for three radially arranged arrays of laser diodes is presented. The design of a customized prototype diode side-pumped high-power laser head fabricated for the purpose of testing is discussed. A detailed comparative experimental and simulation study of the dynamic operation and the beam characteristics that are used to verify the accuracy of the proposed model for analyzing the performance of high-power DPSSLs under different conditions are discussed. The simulated and measured results of power, pump distribution, beam shape, and slope efficiency are shown under different conditions and for a specific case, where the targeted output power is 140 W, while the input pumping power is 400 W. The 95% output coupler reflectivity showed good agreement with the slope efficiency, which is approximately 35%; this assures the robustness of the proposed model to accurately predict the design parameters of practical, high-power DPSSLs.

  4. New progress in high-power picosecond ultraviolet laser%高功率皮秒紫外激光器新进展

    Institute of Scientific and Technical Information of China (English)

    毛小洁

    2015-01-01

    高功率皮秒紫外激光器在高精密加工、激光医疗、光电对抗和光伏产业等领域有重要应用,近年来成为固体激光新光源研究热点。本文对国内外基于和频技术的高功率皮秒紫外激光器研究新进展进行了归纳和总结。首先,阐述了和频工作原理,介绍了和频产生皮秒紫外激光的非线性晶体;然后,介绍了国内外高功率皮秒紫外激光器的新进展,包括:高功率皮秒紫外激光器、高峰值功率皮秒紫外激光器、高功率和高峰值功率皮秒紫外激光器。最后,展望了高功率皮秒紫外激光器的进一步发展及应用。归纳和总结表明:高功率皮秒紫外激光器在国外较成熟,国内在该领域的研究刚刚起步。光子晶体光纤和碟片激光器输出基频光的皮秒紫外激光器有突出的优势,已成为皮秒紫外激光产业的主力军。%High-power picosecond ultraviolet lasers have attracted considerable interests as novel laser source, due to their wide applications in high precision product, laser medical system, optoelectronic countermeasure and structuring of silicon.The research and development on high-power picosecond ultraviolet laser based on technology of sum frequency are classified and summarized.First, the mechanism of sum frequency and pico-second ultraviolet crystal are discussed.Then the high-power picosecond ultraviolet laser, the high-peak-power picosecond ultraviolet laser, and the high-power and high-peak-power picosecond ultraviolet lasers are dis-cussed.Finally, the prospect of further development and applications of high-power picosecond ultraviolet la-ser sources is put forward.According to the latest development, it is indicated that the high power picosecond ultraviolet lasers developed in abroad is in maturity stage but just in starting stage at.The high-power picosec-ond ultraviolet lasers based on photonic crystal fiber laser and thin disk laser have some merits

  5. Applications of lasers and electro-optics

    Science.gov (United States)

    Tan, B. C.; Low, K. S.; Chen, Y. H.; Ahmad, Harith; Tou, T. Y.

    Supported by the IRPA Programme on Laser Technology and Applications, many types of lasers have been designed, constructed and applied in various areas of science, medicine and industries. Amongst these lasers constructed were high power carbon dioxide lasers, rare gas halide excimer lasers, solid state Neodymium-YAG lasers, nitrogen lasers, flashlamp pumped dye lasers and nitrogen and excimer laser pumped dye lasers. These lasers and the associated electro-optics system, some with computer controlled, are designed and developed for the following areas of applications: (1) industrial applications of high power carbon dioxide lasers for making of i.c. components and other materials processing purposes -- prototype operational systems have been developed; (2) Medical applications of lasers for cancer treatment using the technique of photodynamic therapy -- a new and more effective treatment protocol has been proposed; (3) agricultural applications of lasers in palm oil and palm fruit-fluorescence diagnostic studies -- fruit ripeness signature has been developed and palm oil oxidation level were investigated; (4) development of atmospheric pollution monitoring systems using laser lidar techniques -- laboratory scale systems were developed; and (5) other applications of lasers including laser holographic and interferometric methods for the non destructive testing of materials.

  6. High Power Fibre Laser System for a High Repetition Rate Laserwire

    CERN Document Server

    Nevay, L J; Corner, L

    2014-01-01

    We present the development of a high power fibre laser system to investigate its suitability for use in a transverse electron beam profile monitor i.e. a laserwire. A system capable of producing individual pulses up to $165.8 \\pm 0.4 \\mu$J at 1036 nm with a full-width at half-maximum of $1.92 \\pm 0.12$ps at 6.49 MHz is demonstrated using a master oscillator power amplifier design with a final amplification stage in a rod-type photonic crystal fibre. The pulses are produced in trains of 1 ms in a novel burst mode amplification scheme to match the bunch pattern of the charged particles in an accelerator. This method allows pulse energies up to an order of magnitude greater than the steady-state value of $17.0 \\pm 0.6 \\mu$J to be achieved at the beginning of the burst with a demonstrated peak power of $25.8 \\pm 1.7$ MW after compression. The system is also shown to demonstrate excellent spatial quality with an $M^{2} = 1.26 \\pm 0.01$ in both dimensions which would allow nearly diffraction limited focussing to be...

  7. High-power passively Q-switched Nd:KGW laser pumped at 877 nm

    Science.gov (United States)

    Huang, K.; Ge, W. Q.; Zhao, T. Z.; Feng, C. Y.; Yu, J.; He, J. G.; Xiao, H.; Fan, Z. W.

    2016-06-01

    In this work, we demonstrate, for the first time, a high-power passively Q-switched Ng-cut Nd3+:KGd(WO4)2/Cr4+:YAG laser pumped at 877 nm. The maximum average output power of ~1.6 W is obtained at the pump power of 5.22 W, when a saturable absorber with 98 % of initial transmission is used. The corresponding pulse energy is up to 16 µJ. The maximum pulse energy of 25.3 µJ is achieved at a repetition rate of 59 kHz, by employing a saturable absorber with 95 % of initial transmission. The corresponding pulse width and average output power are 89.0 ns and 1.5 W, respectively. A careful cavity design and a good thermal management ensure nearly TEM00 output with M 2 ≤ 1.22 within the whole range of operation in both N p and N m directions at 877 nm pump.

  8. Quantum Transport Simulation of High-Power 4.6-μm Quantum Cascade Lasers

    Directory of Open Access Journals (Sweden)

    Olafur Jonasson

    2016-06-01

    Full Text Available We present a quantum transport simulation of a 4.6- μ m quantum cascade laser (QCL operating at high power near room temperature. The simulation is based on a rigorous density-matrix-based formalism, in which the evolution of the single-electron density matrix follows a Markovian master equation in the presence of applied electric field and relevant scattering mechanisms. We show that it is important to allow for both position-dependent effective mass and for effective lowering of very thin barriers in order to obtain the band structure and the current-field characteristics comparable to experiment. Our calculations agree well with experiments over a wide range of temperatures. We predict a room-temperature threshold field of 62 . 5 kV/cm and a characteristic temperature for threshold-current-density variation of T 0 = 199 K . We also calculate electronic in-plane distributions, which are far from thermal, and show that subband electron temperatures can be hundreds to thousands of degrees higher than the heat sink. Finally, we emphasize the role of coherent tunneling current by looking at the size of coherences, the off-diagonal elements of the density matrix. At the design lasing field, efficient injection manifests itself in a large injector/upper lasing level coherence, which underscores the insufficiency of semiclassical techniques to address injection in QCLs.

  9. High power fiber laser system for a high repetition rate laserwire

    Directory of Open Access Journals (Sweden)

    L. J. Nevay

    2014-07-01

    Full Text Available We present the development of a high power fiber laser system to investigate its suitability for use in a transverse electron beam profile monitor, i.e., a laserwire. A system capable of producing individual pulses up to 165.8±0.4  μJ at 1036 nm with a full width at half maximum of 1.92±0.12  ps at 6.49 MHz is demonstrated using a master oscillator power amplifier design with a final amplification stage in a rod-type photonic crystal fiber. The pulses are produced in trains of 1 ms in a novel burst mode amplification scheme to match the bunch pattern of the charged particles in an accelerator. This method allows pulse energies up to an order of magnitude greater than the steady-state value of 17.0±0.6  μJ to be achieved at the beginning of the burst with a demonstrated peak power of 25.8±1.7  MW after compression. The system is also shown to demonstrate excellent spatial quality with an M^{2}=1.26±0.01 in both dimensions, which would allow nearly diffraction limited focusing to be achieved.

  10. Verification and analysis of stray light in high-power laser system

    Science.gov (United States)

    Huang, PingXian; Cen, Zhaofeng; Li, Xiaotong; Jin, Yuan

    2014-11-01

    In the high-power laser system, the stray light which is generated by the surface's residual reflection of optical elements and the multi-pass transmission in the system will lead to temperature increase in part of the system, the optical elements deformation and damage, distortion of wave-front and change of the beam's divergence angle, which seriously influence the beam's quality and propagation properties and damage the components in the system. So, it is very important to use the relevant software to analyze the stray light rigorously because the reliability and precision of the software is the guarantee of reliable results. Through two types of software we performed the simulation of the stray light in the system, including ghost's distribution in the case of different states of rotating defocusing, beam's pointing. Simultaneously, the impact of processing and assembling errors is analyzed in details. We built a specialized experiment to verify the reliability of results of the software and the related parameters of system are conveniently measured with the device.

  11. A laboratory model of post-Newtonian gravity with high power lasers and 4th generation light sources

    Science.gov (United States)

    Gregori, G.; Levy, M. C.; Wadud, M. A.; Crowley, B. J. B.; Bingham, R.

    2016-04-01

    Using the post-Newtonian formalism of gravity, we attempt to calculate the x-ray Thomson scattering cross section of electrons that are accelerated in the field of a high intensity optical laser. We show that our results are consistent with previous calculations, suggesting that the combination of high power laser and 4th generation light sources may become a powerful platform to test models exploring high order corrections to the Newtonian gravity.

  12. Nonlinear optical compression of high-power 10-μm CO2 laser pulses in gases and semiconductors

    Science.gov (United States)

    Pigeon, Jeremy; Tochitsky, Sergei; Joshi, Chan

    2017-03-01

    We review a series of experiments on nonlinear optical compression of high-power, picosecond, 10-µm CO2 laser pulses. Presented schemes include self-phase modulation in a Xe-filled hollow glass waveguide, self-phase modulation in GaAs followed by compression, and multiple four-wave mixing compression of a laser beat-wave in GaAs. The novel nonlinear optics and technical challenges uncovered through these experiments are discussed.

  13. Evaluation of a new high power, wide separation laser Doppler probe : Potential measurement of deeper tissue blood flow

    NARCIS (Netherlands)

    Clough, Geraldine; Chipperfield, Andrew; Byrne, Christopher; de Mul, Frits; Gush, Rodney

    2009-01-01

    Objective: To compare the output from a novel high power, wide separation laser Doppler flow probe (DP1-V2-HP, 4 mm, with IRLD20) with that of a standard flow probe (DP1-V2, 0.5 mm, with DRT4) (Moor UK) and to explore its potential for use in the noninvasive measurement of blood flow in deeper tissu

  14. Characterization and Performance of a High-Power Solid-State Laser for a High-Current Photocathode Injector

    CERN Document Server

    Zhang, S; Neil, G; Shinn, M D

    2005-01-01

    We report the characterization and performance of a diode-pumped, high-power, picosecond laser system designed for high-current photo-cathode accelerator injector at repetition rates of both 75MHz and 750MHz. Our characterization includes measurement of the system's amplitude stability, beam quality, pulsewidth, and phase noise for both frequencies.

  15. Beam shaping to provide round and square-shaped beams in optical systems of high-power lasers

    Science.gov (United States)

    Laskin, Alexander; Laskin, Vadim

    2016-05-01

    Optical systems of modern high-power lasers require control of irradiance distribution: round or square-shaped flat-top or super-Gaussian irradiance profiles are optimum for amplification in MOPA lasers and for thermal load management while pumping of crystals of solid-state ultra-short pulse lasers to control heat and minimize its impact on the laser power and beam quality while maximizing overall laser efficiency, variable profiles are also important in irradiating of photocathode of Free Electron lasers (FEL). It is suggested to solve the task of irradiance re-distribution using field mapping refractive beam shapers like piShaper. The operational principle of these devices presumes transformation of laser beam intensity from Gaussian to flat-top one with high flatness of output wavefront, saving of beam consistency, providing collimated output beam of low divergence, high transmittance, extended depth of field, negligible residual wave aberration, and achromatic design provides capability to work with ultra-short pulse lasers having broad spectrum. Using the same piShaper device it is possible to realize beams with flat-top, inverse Gauss or super Gauss irradiance distribution by simple variation of input beam diameter, and the beam shape can be round or square with soft edges. This paper will describe some design basics of refractive beam shapers of the field mapping type and optical layouts of their applying in optical systems of high-power lasers. Examples of real implementations and experimental results will be presented as well.

  16. High-power Q-switched erbium-ytterbium codoped fiber laser using multiwalled carbon nanotubes saturable absorber

    Science.gov (United States)

    Ab Razak, Mohd Zulhakimi; Saleh, Zatul Saliza; Ahmad, Fauzan; Anyi, Carol Livan; Harun, Sulaiman W.; Arof, Hamzah

    2016-10-01

    Due to an enormous potential of pulsed lasers in applications such as manufacturing, metrology, environmental sensing, and biomedical diagnostics, a high-power and stable Q-switched erbium-ytterbium codoped double-clad fiber laser (EYDFL) incorporating of multiwall carbon nanotubes (MWCNTs) saturable absorber (SA) made based on polyvinyl alcohol (PVA) with a 3∶2 ratio is demonstrated. The SA was fabricated by mixing a dilute PVA solution with an MWCNTs homogeneous solution. Subsequently, the mixture was sonicated and centrifuged to produce a homogeneous suspension that was left to dry at room temperature to form the MWCNTs-PVA film. The SA was formed by inserting the film between a pair of FC/PC fiber connectors. Then, it was integrated into the EYDFL's ring cavity, which uses a 5-m-long erbium-ytterbium codoped fiber (EYDF). The lasing threshold for the Q-switched EYDFL was at 330 mW. At the maximum available pump power of 900 mW, the proposed EYDFL produced Q-switched pulses with a repetition rate of 74.85 kHz, pulsewidth of ˜3.6 μs, and an average output power of about 5 mW. The maximum energy per pulse of ˜85 nJ was obtained at pump power of ˜700 mW with peak power of 21 mW.

  17. Technology of discharge and laser resonators for high power CO2 lasers. Koshutsuryoku CO2 laser ni tsukawareru hoden reiki laser kyoshinki gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Takenaka, Y.; Kuzumoto, M. (Mitsubishi Electric Corp., Tokyo (Japan))

    1994-03-20

    This paper describes discharge excitation technology and resonator technology as basic technologies for high power CO2 lasers. As a result of progress in high-frequency power element techniques, the discharge excitation technology now generally uses laser excitation using AC discharge of capacity coupling type. Its representative example is silent discharge (SD) excitation. This is a system to excite laser by applying high voltages with as high frequency as 100 kHz to 1 MHz across a pair of electrodes covered with a dielectric material. The system maintains stability in discharge even if power supply voltage amplitude is modulated, and easily provides pulse outputs. Discharge excitation for diffusion cooled type CO2 laser generates a discharge in a gap with a gap length of about 2 mm, and can perform gas cooling by means of thermal conduction of gas, whereas a compact resonator can be fabricated. A resonator for the diffusion cooled type CO2 laser eliminates gas circulation and cooling systems, hence the device can be made more compact. A report has been given that several of these compact resonators were combined, from which a laser output of 85W was obtained by using RF discharge of 2kW. 43 refs., 21 figs.

  18. Three-phase multilevel inverter configuration for open-winding high power application

    DEFF Research Database (Denmark)

    Sanjeevikumar, Padmanaban; Blaabjerg, Frede; Wheeler, Patrick William

    2015-01-01

    This paper work exploits a new dual open-winding three-phase multilevel inverter configuration suitable for high power medium-voltage applications. Modular structure comprised of standard three-phase voltage source inverter (VSI) along with one additional bi-directional semiconductor device (MOSF...

  19. Industrial grade fiber-coupled laser systems delivering ultrashort high-power pulses for micromachining

    Science.gov (United States)

    Pricking, Sebastian; Welp, Petra; Overbuschmann, Johannes; Nutsch, Sebastian; Gebs, Raphael; Fleischhaker, Robert; Kleinbauer, Jochen; Wolf, Martin; Budnicki, Aleksander; Sutter, Dirk H.; Killi, Alexander; Mielke, Michael

    2016-03-01

    We report on an industrial fiber-delivered laser system producing ultra-short pulses in the range of a few picoseconds down to a few hundred femtoseconds with high average power suitable for high-precision micromachining. The delivery fiber is a hollow-core photonic crystal fiber with a Kagomé shaped lattice and a hypocycloid core wall enabling the guiding of laser radiation over several meters with exceptionally low losses and preservation of high beam quality (M2laser head providing a compact footprint without the need for external boxes. The laser head is carefully designed regarding its thermo-mechanical properties to allow a highly reliable coupling stability. The exchangeable delivery fiber is packaged using Trumpf's well established LLK-D connectors which offer a very high mechanical precision, the possibility to add water cooling, as well as full featured safety functions. The fiber is hermetically sealed and protected by a robust but flexible shield providing bend protection and break detection. We show the linear and nonlinear optical properties of the transported laser radiation and discuss its feasibility for pulse compression. Measurements are supported by simulation of pulse propagation by solving the nonlinear Schrödinger equation implementing the split-step Fourier method. In addition, mode properties are measured and confirmed by finite element method simulations. The presented industrial laser system offers the known advantages of ultra-short pulses combined with the flexibility of fiber delivery yielding a versatile tool perfectly suitable for all kinds of industrial micromachining applications.

  20. Design and fabrication of hollow-core photonic crystal fibers for high power fast laser beam transportation and pulse compression

    Science.gov (United States)

    Wang, Y. Y.; Peng, Xiang; Alharbi, M.; Dutin, C. F.; Bradley, T. D.; Mielke, Michael; Booth, Timothy; Benabid, F.

    2012-03-01

    We report on recent design and fabrication of Kagome type hollow-core photonic crystal fiber (HC-PCF) for the purpose of high power fast laser beam transportation. The fabricated seven-cell three-ring hypocycloid-shaped large core fiber exhibits an up-to-date lowest attenuation (among all Kagome fibers) of 40dB/km over a broadband transmission centered at 1500nm. We show that the large core size, low attenuation, broadband transmission, single modedness, low dispersion and relatively low banding loss makes it an ideal host for high power laser beam transportation. By filling the fiber with helium gas, a 74μJ, 850fs and 40kHz repetition rate ultra-short pulse at 1550nm has been faithfully delivered with little propagation pulse distortion. Compression of a 105μJ laser pulse from 850fs to 300fs has been achieved by operating the fiber in ambient air.

  1. Evolution of Electron Phase Orbits of Multi-photon Nonlinear Compton Scattering in High Power Laser-plasma

    Institute of Scientific and Technical Information of China (English)

    HAO Dong-shan; L(U) Jian

    2005-01-01

    The evolution of the electron phase orbits based on the multi-photon nonlinear Compton scattering with the high power laser-plasma is discussed by using Kroll-Morton-Rosenbluth theory. The random evolution of the un-captured electron phase orbits from periodicity to non-periodicity is found after the energy has been exchanged between the electron and photons. With the increase of the absorbed photon number n by an electron,this evolution will be more and more intense, while which is rapidly decreased with the enhancement of the collision non-flexibility ξ and their initial speeds of the electrons and photons, but this evolution is lower than that in the high power laser field. When the electrons are captured by the laser field, the evolution is finished, and the electrons will stably transport,and the photons don't provide the energy for these electrons any more.

  2. Propagation characteristics of a high-power broadband laser beam passing through a nonlinear optical medium with defects

    Institute of Scientific and Technical Information of China (English)

    Xueqiong; Chen; Xiaoyan; Li; Ziyang; Chen; Jixiong; Pu; Guowen; Zhang; Jianqiang; Zhu

    2013-01-01

    The intensity distributions of a high-power broadband laser beam passing through a nonlinear optical medium with defects and then propagating in free space are investigated based on the general nonlinear Schr¨odinger equation and the split-step Fourier numerical method. The influences of the bandwidth of the laser beam, the thickness of the medium,and the defects on the light intensity distribution are revealed. We find that the nonlinear optical effect can be suppressed and that the uniformity of the beam can be improved for a high-power broadband laser beam with appropriate wide bandwidth. It is also found that, under the same incident light intensity, a thicker medium will lead to a stronger self-focusing intensity, and that the influence of defects in the optical elements on the intensity is stronger for a narrowband beam than for a broadband beam.

  3. Efficient, high-power, ytterbium-fiber-laser-pumped picosecond optical parametric oscillator.

    Science.gov (United States)

    Kokabee, O; Esteban-Martin, A; Ebrahim-Zadeh, M

    2010-10-01

    We report a high-power picosecond optical parametric oscillator (OPO) synchronously pumped by a Yb fiber laser at 1.064 μm, providing 11.7 W of total average power in the near to mid-IR at 73% extraction efficiency. The OPO, based on a 50 mm MgO:PPLN crystal, is pumped by 20.8 ps pulses at 81.1 MHz and can simultaneously deliver 7.1 W of signal at 1.56 μm and 4.6 W of idler at 3.33 μm for 16 W of pump power. The oscillator has a threshold of 740 mW, with maximum signal power of 7.4 W at 1.47 μm and idler power of 4.9 W at 3.08 μm at slope efficiencies of 51% and 31%, respectively. Wavelength coverage across 1.43-1.63 μm (signal) and 4.16-3.06 μm (idler) is obtained, with a total power of ~11 W and an extraction efficiency of ~68%, with pump depletion of ~78% maintained over most of the tuning range. The signal and idler output have a single-mode spatial profile and a peak-to-peak power stability of ±1.8% and ±2.9% over 1 h at the highest power, respectively. A signal pulse duration of 17.3 ps with a clean single-peak spectrum results in a time-bandwidth product of ~1.72, more than four times below the input pump pulses.

  4. System analysis of wavelength beam combining of high-power diode lasers for photoacoustic endoscopy

    Science.gov (United States)

    Leggio, Luca; Gallego, Daniel C.; Gawali, Sandeep B.; Sánchez, Miguel; Rodriguez, Sergio; Osiński, Marek; Sacher, Joachim; Carpintero, Guillermo; Lamela, Horacio

    2016-04-01

    This paper, originally published on 27 April 2016, was replaced with a corrected/revised version on 8 June 2016. If you downloaded the original PDF but are unable to access the revision, please contact SPIE Digital Library Customer Service for assistance. The purpose of wavelength-beam combining (WBC) is to improve the output power of a multi-wavelength laser system while maintaining the quality of the combined beam. This technique has been primarily proposed for industrial applications, such as metal cutting and soldering, which require optical peak power between kilowatts and megawatts. In order to replace the bulkier solid-state lasers, we propose to use the WBC technique for photoacoustic (PA) applications, where a multi-wavelength focused beam with optical peak power between hundreds of watts up to several kilowatts is necessary to penetrate deeply into biological tissues. In this work we present an analytical study about the coupling of light beams emitted by diode laser bars at 808 nm, 880 nm, 910 nm, 940 nm, and 980 nm into a .

  5. Beam shaping in high-power broad-area quantum cascade lasers using optical feedback

    Science.gov (United States)

    Ferré, Simon; Jumpertz, Louise; Carras, Mathieu; Ferreira, Robson; Grillot, Frédéric

    2017-03-01

    Broad-area quantum cascade lasers with high output powers are highly desirable sources for various applications including infrared countermeasures. However, such structures suffer from strongly deteriorated beam quality due to multimode behavior, diffraction of light and self-focusing. Quantum cascade lasers presenting high performances in terms of power and heat-load dissipation are reported and their response to a nonlinear control based on optical feedback is studied. Applying optical feedback enables to efficiently tailor its near-field beam profile. The different cavity modes are sequentially excited by shifting the feedback mirror angle. Further control of the near-field profile is demonstrated using spatial filtering. The impact of an inhomogeneous gain as well as the influence of the cavity width are investigated. Compared to existing technologies, that are complex and costly, beam shaping with optical feedback is a more flexible solution to obtain high-quality mid-infrared sources.

  6. Terahertz quantum-cascade lasers as high-power and wideband, gapless sources for spectroscopy.

    Science.gov (United States)

    Röben, Benjamin; Lü, Xiang; Hempel, Martin; Biermann, Klaus; Schrottke, Lutz; Grahn, Holger T

    2017-07-10

    Terahertz (THz) quantum-cascade lasers (QCLs) are powerful radiation sources for high-resolution and high-sensitivity spectroscopy with a discrete spectrum between 2 and 5 THz as well as a continuous coverage of several GHz. However, for many applications, a radiation source with a continuous coverage of a substantially larger frequency range is required. We employed a multi-mode THz QCL operated with a fast ramped injection current, which leads to a collective tuning of equally-spaced Fabry-Pérot laser modes exceeding their separation. A continuous coverage over 72 GHz at about 4.7 THz was achieved. We demonstrate that the QCL is superior to conventional sources used in Fourier transform infrared spectroscopy in terms of the signal-to-noise ratio as well as the dynamic range by one to two orders of magnitude. Our results pave the way for versatile THz spectroscopic systems with unprecedented resolution and sensitivity across a wide frequency range.

  7. Beam shaping in high-power broad-area quantum cascade lasers using optical feedback

    Science.gov (United States)

    Ferré, Simon; Jumpertz, Louise; Carras, Mathieu; Ferreira, Robson; Grillot, Frédéric

    2017-01-01

    Broad-area quantum cascade lasers with high output powers are highly desirable sources for various applications including infrared countermeasures. However, such structures suffer from strongly deteriorated beam quality due to multimode behavior, diffraction of light and self-focusing. Quantum cascade lasers presenting high performances in terms of power and heat-load dissipation are reported and their response to a nonlinear control based on optical feedback is studied. Applying optical feedback enables to efficiently tailor its near-field beam profile. The different cavity modes are sequentially excited by shifting the feedback mirror angle. Further control of the near-field profile is demonstrated using spatial filtering. The impact of an inhomogeneous gain as well as the influence of the cavity width are investigated. Compared to existing technologies, that are complex and costly, beam shaping with optical feedback is a more flexible solution to obtain high-quality mid-infrared sources. PMID:28287175

  8. Thermal Investigation of Interaction between High-power CW-laser Radiation and a Water-jet

    Science.gov (United States)

    Brecher, Christian; Janssen, Henning; Eckert, Markus; Schmidt, Florian

    The technology of a water guided laser beam has been industrially established for micro machining. Pulsed laser radiation is guided via a water jet (diameter: 25-250 μm) using total internal reflection. Due to the cylindrical jet shape the depth of field increases to above 50 mm, enabling parallel kerfs compared to conventional laser systems. However higher material thicknesses and macro geometries cannot be machined economically viable due to low average laser powers. Fraunhofer IPT has successfully combined a high-power continuous-wave (CW) fiber laser (6 kW) and water jet technology. The main challenge of guiding high-power laser radiation in water is the energy transferred to the jet by absorption, decreasing its stability. A model of laser water interaction in the water jet has been developed and validated experimentally. Based on the results an upscaling of system technology to 30 kW is discussed, enabling a high potential in cutting challenging materials at high qualities and high speeds.

  9. Microstructure, microhardness and corrosion resistance of remelted TiG2 and Ti6Al4V by a high power diode laser

    Energy Technology Data Exchange (ETDEWEB)

    Amaya-Vazquez, M.R. [Laboratorio de Corrosion y Proteccion, Universidad de Cadiz, Departamento de Ciencia de los Materiales e Ingenieria Metalurgica y Quimica Inorganica, Avda. Republica Saharaui s/n, 11510 Puerto Real, Cadiz (Spain); Sanchez-Amaya, J.M., E-mail: josemaria.sanchez@uca.es [Titania, Ensayos y Proyectos Industriales S.L., Ctra Sanlucar A-2001 Km 7,5, Parque Tecnologico TecnoBahia-Edif. RETSE Nave 4, 11500 El Puerto de Santa Maria, Cadiz (Spain); Departamento de Fisica Aplicada, CASEM, Avda. Republica Saharaui s/n, 11510-Puerto Real, Cadiz (Spain); Boukha, Z.; Botana, F.J. [Laboratorio de Corrosion y Proteccion, Universidad de Cadiz, Departamento de Ciencia de los Materiales e Ingenieria Metalurgica y Quimica Inorganica, Avda. Republica Saharaui s/n, 11510 Puerto Real, Cadiz (Spain)

    2012-03-15

    Highlights: Black-Right-Pointing-Pointer Laser remelting of TiG2 and Ti6Al4V is performed with argon shielded diode laser. Black-Right-Pointing-Pointer Microstructure, microhardness and corrosion of remelted samples are deeply analysed. Black-Right-Pointing-Pointer Microstructural changes of laser remelted TiG2 lead to microhardness increase. Black-Right-Pointing-Pointer Remelted Ti6Al4V presents microhardness increase and corrosion improvement. Black-Right-Pointing-Pointer Martensite depth in remelted Ti6Al4V is linearly proportional to laser fluence. - Abstract: The high strength, low density and superior corrosion resistance allow titanium alloys to be widely employed in different industrial applications. The properties of these alloys can be modulated by different heat treatments, including laser processing. In the present paper, laser remelting treatments, performed with a high power diode laser, were applied to samples of two titanium alloys (TiG2 and Ti6Al4V). The influence of the applied laser fluence on microstructure, microhardness and corrosion resistance is investigated. Results show that laser remelting treatments with appropriate fluences provoke microstructural changes leading to microhardness increase and corrosion resistance improvement.

  10. Green high-power tunable external-cavity GaN diode laser at 515 nm

    DEFF Research Database (Denmark)

    Chi, Mingjun; Jensen, Ole Bjarlin; Petersen, Paul Michael

    2016-01-01

    A 480 mW green tunable diode laser system is demonstrated for the first time to our knowledge. The laser system is based on a GaN broad-area diode laser and Littrow external-cavity feedback. The green laser system is operated in two modes by switching the polarization direction of the laser beam ...

  11. High-Power Single-Mode 2.65-micron InGaAsSb/AlInGaAsSb Diode Lasers

    Science.gov (United States)

    Frez, Clifford F.; Briggs, Ryan M.; Forouhar, Siamak; Borgentun, Carl E.; Gupta, James

    2013-01-01

    Central to the advancement of both satellite and in-situ science are improvements in continuous-wave and pulsed infrared laser systems coupled with integrated miniaturized optics and electronics, allowing for the use of powerful, single-mode light sources aboard both satellite and unmanned aerial vehicle platforms. There is a technological gap in supplying adequate laser sources to address the mid-infrared spectral window for spectroscopic characterization of important atmospheric gases. For high-power applications between 2 to 3 micron, commercial laser technologies are unsuitable because of limitations in output power. For instance, existing InP-based laser systems developed for fiber-based telecommunications cannot be extended to wavelengths longer than 2 micron. For emission wavelengths shorter than 3 micron, intersubband devices, such as infrared quantum cascade lasers, become inefficient due to band-offset limitations. To date, successfully demonstrated singlemode GaSb-based laser diodes emitting between 2 and 3 micron have employed lossy metal Bragg gratings for distributed- feedback coupling, which limits output power due to optical absorption. By optimizing both the quantum well design and the grating fabrication process, index-coupled distributed-feedback 2.65-micron lasers capable of emitting in excess of 25 mW at room temperature have been demonstrated. Specifically, lasers at 3,777/cm (2.65 micron) have been realized to interact with strong absorption lines of HDO and other isotopologues of H2O. With minor modifications of the optical cavity and quantum well designs, lasers can be fabricated at any wavelength within the 2-to-3-micron spectral window with similar performance. At the time of this reporting, lasers with this output power and wavelength accuracy are not commercially available. Monolithic ridge-waveguide GaSb lasers were fabricated that utilize secondorder lateral Bragg gratings to generate single-mode emission from InGaAsSb/ Al

  12. Investigations of high power laser beam interaction with material by means of hybrid FVM-FEM and digital image correlation methods

    Science.gov (United States)

    Kujawińska, M.; Łapka, P.; Malesa, M.; Malowany, K.; Prasek, M.; Marczak, J.

    2016-12-01

    The paper presents the new approach to the analysis of interaction between a high power laser beam and matter. The method relies on the combined experimental-numerical spatio-temporal analysis of temperature, displacement and strain maps which are generated at a surface of an object illuminated by a high power laser beam. Transient heat transfer numerical simulations were carried out applying the FVM, while the quasi-transient structural analyses were performed with the aid of the FEM. The displacement maps were captured by means of 3D Digital Image Correlation method, and temperature maps were provided by a high speed IR camera. The experimental data are compared to the initial model of laser induced heat transfer in an object and resulting displacements/strains. The first approach to hybrid experimental-numerical method which aims in indirect determination of laser beam profile is described. The monitoring of displacement/strain maps directly at an illuminated object may be also used for a structural integrity analysis of a target. In the paper at first the numerical simulations applied to model laser beam thermal interaction with solid bodies are presented. Next the laboratory experimental stand is described and the results of the initial tests performed at aluminum and bronze samples are shown and compared with numerical simulations. The advantages and disadvantages of the proposed methodology are discussed in relation to the two applications mentioned above.

  13. Full characterization of the amplified spontaneous emission from a diode-pumped high-power laser system.

    Science.gov (United States)

    Keppler, S; Hornung, M; Bödefeld, R; Sävert, A; Liebetrau, H; Hein, J; Kaluza, M C

    2014-05-01

    We present the first complete temporal and spatial characterization of the amplified spontaneous emission (ASE) of laser radiation generated by a diode-pumped high-power laser system. The ASE of the different amplifiers was measured independently from the main pulse and was characterized within a time window of -10ms ≤ t ≤ 10ms and an accuracy of up to 15fs around the main pulse. Furthermore, the focusability and the energy of the ASE from each amplifier was measured after recompression. Using our analysis method, the laser components, which need to be optimized for a further improvement of the laser contrast, can be identified. This will be essential for laser-matter interaction experiments requiring a minimized ASE intensity or fluence.

  14. Experimental and numerical investigation on cladding of corrosion-erosion resistant materials by a high power direct diode laser

    Science.gov (United States)

    Farahmand, Parisa

    advantages due to creating coating layers with superior properties in terms of purity, homogeneity, low dilution, hardness, bonding, and microstructure. In the development of modern materials for hardfacing applications, the functionality is often improved by combining materials with different properties into composites. Metal Matrix Composite (MMC) coating is a composite material with two constituent parts, i.e., matrix and the reinforcement. This class of composites are addressing improved mechanical properties such as stiffness, strength, toughness, and tribological and chemical resistance. Fabrication of MMCs is to achieve a combination of properties not achievable by any of the materials acting alone. MMCs have attracted significant attention for decades due to their combination of wear-resistivity, corrosion-resistivity, thermal, electrical and magnetic properties. Presently, there is a strong emphasis on the development of advanced functional coatings for corrosion, erosion, and wear protection for different industrial applications. In this research, a laser cladding system equipped with a high power direct diode laser associated with gas driven metal powder delivery system was used to develop advanced MMC coatings. The high power direct diode laser used in this study offers wider beam spot, shorter wavelength and uniform power distribution. These properties make the cladding set-up ideal for coating due to fewer cladding tracks, lower operation cost, higher laser absorption, and improved coating qualities. In order to prevent crack propagation, porosity, and uniform dispersion of carbides in MMC coating, cladding procedure was assisted by an induction heater as a second heat source. The developed defect free MMC coatings were combined with nano-size particles of WC, rare earth (RE) element (La2O3), and Mo as a refractory metal to enhance mechanical properties, chemical composition, and subsequently improve the tribological performance of the coatings. The resistance

  15. Efficient generation of 3.5 W laser light at 515 nm by frequency doubling a single-frequency high power DBR tapered diode laser

    Science.gov (United States)

    Jensen, Ole Bjarlin; Hansen, Anders Kragh; Müller, André; Sumpf, Bernd; Petersen, Paul Michael; Andersen, Peter E.

    2017-06-01

    More than 3.5 W of green light at 515 nm is generated by frequency doubling a single-frequency high power DBR tapered diode laser. The frequency doubling is performed in a cascade of PPMgLN and PPMgSLT crystals in order to reach high power and avoid thermal effects present in PPMgLN at high power. The green light is diffraction limited (M2 <1.1) and single-frequency operation is demonstrated with a linewidth less than 2 pm.

  16. Computational fluid dynamic modeling of gas flow characteristics of the high-power CW CO2 laser

    Institute of Scientific and Technical Information of China (English)

    Hongyau Huang; Youqing Wang

    2011-01-01

    @@ To increase the photoelectronic conversion efficiency of the single discharge tube and to meet the requirements of the laser cutting system, optimization of the discharge tube structure and gas flow field is necessary. We present a computational fluid dynamic model to predict the gas flow characteristics of high-power fast-axial flow CO2 laser. A set of differential equations is used to describe the operation of the laser. Gas flow characteristics, are calculated. The effects of gas velocity and turbulence intensity on discharge stability are studied. Computational results are compared with experimental values, and a good agreement is observed. The method presented and the results obtained can make the design process more efficient.%To increase the photoelectronic conversion efficiency of the single discharge tube and to meet the requirements of the laser cutting system, optimization of the discharge tube structure and gas flow field is necessary. We present a computational fluid dynamic model to predict the gas flow characteristics of high-power fast-axial flow CO2 laser. A set of differential equations is used to describe the operation of the laser. Gas flow characteristics, are calculated. The effects of gas velocity and turbulence intensity on discharge stability are studied. Computational results are compared with experimental values, and a good agreement is observed. The method presented and the results obtained can make the design process more efficient.

  17. Elucidation of phenomena in high-power fiber laser welding and development of prevention procedures of welding defects

    Science.gov (United States)

    Katayama, Seiji; Kawahito, Yousuke

    2009-02-01

    Fiber lasers have been receiving considerable attention because of their advantages of high power, high beam quality and high efficiency, and are expected as one of the desirable heat sources for high-speed and deep-penetration welding. In our researches, therefore, the effects of laser powers and their densities on the weld penetration and the formation of sound welds were investigated in welding of Type 304 austenitic stainless steel, A5052 aluminum alloy or high strength steel plates with four laser beams of about 0.12 to 1 mm in focused spot diameter, and their welding phenomena were observed with high-speed video cameras and X-ray transmission real-time imaging system. It was found that the laser power density exerted a remarkable effect on the increase in weld penetration at higher welding speeds, but on the other hand at low welding speeds deeper-penetration welds could be produced at higher power. Laser-induced plume behavior and its effect on weld penetration, and the mechanisms of spattering, underfilling, porosity and humping were elucidated, sound welds without welding defects could be produced under the improved welding conditions. In addition, importance of the development of focusing optics and the removal of a plume during remote welding will be emphasized in terms of the stable production of constant deep-penetration welds and the reduction in welding defects in high power laser welding.

  18. Stand-off detection and classification of CBRNe using a Lidar system based on a high power femtosecond laser

    Science.gov (United States)

    Izawa, Jun; Yokozawa, Takeshi; Kurata, Takao; Yoshida, Akihiro; Mastunaga, Yasushi; Somekawa, Toshihiro; Eto, Shuzo; Manago, Naohiro; Horisawa, Hideyuki; Yamaguchi, Shigeru; Fujii, Takashi; Kuze, Hiroaki

    2014-10-01

    We propose a stand-off system that enables detection and classification of CBRNe (Chemical, Biological, Radioactive, Nuclear aerosol and explosive solids). The system is an integrated lidar using a high-power (terawatt) femtosecond laser. The detection and classification of various hazardous targets with stand-off distances from several hundred meters to a few kilometers are achieved by means of laser-induced breakdown spectroscopy (LIBS) and two-photon fluorescence (TPF) techniques. In this work, we report on the technical considerations on the system design of the present hybrid lidar system consisting of a nanosecond laser and a femtosecond laser. Also, we describe the current progress in our laboratory experiments that have demonstrated the stand-off detection and classification of various simulants. For the R and N detection scheme, cesium chloride aerosols have successfully been detected by LIBS using a high-power femtosecond laser. For the B detection scheme, TPF signals of organic aerosols such as riboflavin have clearly been recorded. In addition, a compact femtosecond laser has been employed for the LIBS classification of organic plastics employed as e-simulants.

  19. Researching the 915 nm high-power and high-brightness semiconductor laser single chip coupling module

    Science.gov (United States)

    Wang, Xin; Wang, Cuiluan; Wu, Xia; Zhu, Lingni; Jing, Hongqi; Ma, Xiaoyu; Liu, Suping

    2017-02-01

    Based on the high-speed development of the fiber laser in recent years, the development of researching 915 nm semiconductor laser as main pumping sources of the fiber laser is at a high speed. Because the beam quality of the laser diode is very poor, the 915 nm laser diode is generally based on optical fiber coupling module to output the laser. Using the beam-shaping and fiber-coupling technology to improve the quality of output beam light, we present a kind of high-power and high-brightness semiconductor laser module, which can output 13.22 W through the optical fiber. Based on 915 nm GaAs semiconductor laser diode which has output power of 13.91 W, we describe a thoroughly detailed procedure for reshaping the beam output from the semiconductor laser diode and coupling the beam into the optical fiber of which the core diameter is 105 μm and the numerical aperture is 0.18. We get 13.22 W from the output fiber of the module at 14.5 A, the coupling efficiency of the whole module is 95.03% and the brightness is 1.5 MW/cm2 -str. The output power of the single chip semiconductor laser module achieves the advanced level in the domestic use.

  20. Acquisition and processing of coaxial image of molten pool and keyhole in Nd:YAG laser welding with high power

    Institute of Scientific and Technical Information of China (English)

    秦国梁; 齐秀滨; 杨永波; 王旭友; 林尚扬

    2004-01-01

    An experimental setup of acquiring the coaxial visual image of the molten pool and keyhole in high power Nd:YAG laser welding is introduced in this paper. It is one of the most difficult problems in acquiring coaxial image that the coaxial imaging signal of molten pool and keyhole must be separated from the laser beam with high power. This problem was resolved by designing a dichroitic spectroscope. The characteristics of imaging signal were analyzed and the coaxial image of molten pool and keyhole was acquired. A smoothing filter and a homomorphic filter were designed to remove the low frequency noise and to enhance the image according to the characteristics of imaging signal. At last, edges of molten pool and keyhole were detected and extracted based on image segmentation with threshold.