An assessment of chemical properties and hardgrove grindability index of punjab coal

International Nuclear Information System (INIS)

Shahzad, M.; Iqbal, M.M.; Hassan, S.A.

2014-01-01

This paper deals with the delamination of chemical properties and hardgrove grindability index (HGI) of coal samples collected from three different coal fields of Punjab; Eastern Salt Range, Central Salt Range and Makerwal coal fields. The chemical properties of Punjab coal reveal that most of the Punjab coal belongs to sub-bituminous category except coal of Tunnel C section of Makerwal Collieries and Iqbal Mineral coal mine of Dalwal, which are high volatile bituminous and lignite, respectively. The results of the research show that the HGI values of Punjab coal vary from 57 to 92. The eastern salt range coals are found to be the softest coals among that of three coal fields. It was further observed that the HGI values of the Punjab coal decrease with increasing moisture content, fixed carbon and sulphur contents, while it has a positive relation with volatile matter, ash content and gross calorific value. It was concluded that moisture content at its lower range has negligible effect on HGI of the Punjab coal. (author)

A brief petrographic review on Nigerian coal resources

International Nuclear Information System (INIS)

Obaje, N. G.; Abaa, S. I.; Najime, T.; Suh, C. E.

2000-01-01

The coal resources of Nigeria are located mainly within the Benue Trough. In the lower Benue, subbituminous coals occur within the Maastrichtian Mamu Formation. High - volatile bituminous coals are found within the Turonian - Santonian Awgu Formation in the middle Benue while the upper Benue contains lignites and sub-bituminous coals in the Maastrichtian Gombe Sandstone Formation. Maceral analyses show that himinite dominates in the petrographic composition of the lower and upper Benue Trough coals with vitrinite reflectance values ranging from 0.30 to 0.63% Rm. In coals from the middle Benue, vitrinite macerals predominate and Rm values range from 0.74 to 1.25%. The present review suggests that the sub-bituminous coals in the lower and upper Benue are optimum for combustion and sub-optimum for liquefaction; while the high-volatile bituminous coals in the middle Benue, apart form being optimum for liquefaction, are the most suitable as raw material for coke making (carbonization) in steel manufacture

Ignition characteristics of coal blends in an entrained flow furnace

Energy Technology Data Exchange (ETDEWEB)

J. Faundez; B. Arias; F. Rubiera; A. Arenillas; X. Garcia; A.L. Gordon; J.J. Pis [Universidad de Concepcion, Concepcion (Chile)

2007-09-15

Ignition tests were carried out on blends of three coals of different rank - subbituminous, high volatile and low volatile bituminous - in two entrained flow reactors. The ignition temperatures were determined from the gas evolution profiles (CO, CO{sub 2}, NO, O{sub 2}), while the mechanism of ignition was elucidated from these profiles and corroborated by high-speed video recording. Under the experimental conditions of high carbon loading, clear interactive effects were observed for all the blends. Ignition of the lower rank coals (subbituminous, high volatile bituminous) enhanced the ignition of the higher rank coal (low volatile bituminous) in the blends. The ignition temperatures of the blends of the low rank coals (subbituminous-high volatile bituminous) were additive. However, for the rest of the blends the ignition temperatures were always closer to the lower rank coal in the blend. 21 refs., 8 figs.

Organic geochemical studies of the transformation of gymnospermous xylem during peatification and coalification to subbituminous coal

Science.gov (United States)

Hatcher, P.G.; Lerch, H. E.; Verheyen, T.V.

1990-01-01

by two important processes. The first involves loss of methoxyl groups, primarily by demethylation (Fig. 1A). The end products of demethylation are catechol-like structures as shown below in Figure 1B. The second transformation process involves increased cross-linking of the aromatic rings. This cross-linking induces increased carbon substitution of the aromatic rings such that the lignin-derived structures become more highly condensed. During its conversion to coalified xylem in subbituminous coal, lignitic xylem, composed primarily of condensed catechol-like structures, is transformed to a macromolecular material primarily composed of phenol-like structures. The catechol-like structures of lignitic xylem loose a hydroxyl group, which is replaced by a hydrogen to form the phenol-like structure as shown in the example in Figure 1B. The pyrolysis data provided only a few clues as to the fate of the C3-side chain of lignin during coalification. However, the NMR data suggest that this side chain is altered, probably by loss of the hydroxyl groups that are attached in modern lignin. Interference in the NMR analysis by aliphatic components of wood, such as resins, precludes definitive determinations of the fate of the C3-side chain during coalification. ?? 1990.

Environmental Assessment for Lignite Fuel Enhancement Project, Coal Creek Station, Great River Energy, Underwood, North Dakota

Energy Technology Data Exchange (ETDEWEB)

N/A

2004-01-16

The US Department of Energy (DOE) has prepared this EA to assess the environmental impacts of the commercial application of lignite fuel enhancement. The proposed demonstration project would be implemented at Great River Energy's Coal Creek Station near Underwood, North Dakota. The proposed project would demonstrate a technology to increase the heating value of lignite and other high-moisture coals by reducing the moisture in the fuels. Waste heat that would normally be sent to the cooling towers would be used to drive off a percentage of the moisture contained within the lignite. Application of this technology would be expected to boost power-generating efficiencies, provide economic cost savings for lignite and sub-bituminous power plants, and reduce air emissions. The proposed project would be constructed on a previously disturbed site within the Coal Creek Station and no negative impacts would occur in any environmental resource area.

Coal Moisture Estimation in Power Plant Mills

DEFF Research Database (Denmark)

Andersen, Palle; Bendtsen, Jan Dimon; Pedersen, Tom S.

2009-01-01

Knowledge of moisture content in raw coal feed to a power plant coal mill is of importance for efficient operation of the mill. The moisture is commonly measured approximately once a day using offline chemical analysis methods; however, it would be advantageous for the dynamic operation...... of the plant if an on-line estimate were available. In this paper we such propose an on-line estimator (an extended Kalman filter) that uses only existing measurements. The scheme is tested on actual coal mill data collected during a one-month operating period, and it is found that the daily measured moisture...

Low-rank coal study : national needs for resource development. Volume 2. Resource characterization

Energy Technology Data Exchange (ETDEWEB)

1980-11-01

Comprehensive data are presented on the quantity, quality, and distribution of low-rank coal (subbituminous and lignite) deposits in the United States. The major lignite-bearing areas are the Fort Union Region and the Gulf Lignite Region, with the predominant strippable reserves being in the states of North Dakota, Montana, and Texas. The largest subbituminous coal deposits are in the Powder River Region of Montana and Wyoming, The San Juan Basin of New Mexico, and in Northern Alaska. For each of the low-rank coal-bearing regions, descriptions are provided of the geology; strippable reserves; active and planned mines; classification of identified resources by depth, seam thickness, sulfur content, and ash content; overburden characteristics; aquifers; and coal properties and characteristics. Low-rank coals are distinguished from bituminous coals by unique chemical and physical properties that affect their behavior in extraction, utilization, or conversion processes. The most characteristic properties of the organic fraction of low-rank coals are the high inherent moisture and oxygen contents, and the correspondingly low heating value. Mineral matter (ash) contents and compositions of all coals are highly variable; however, low-rank coals tend to have a higher proportion of the alkali components CaO, MgO, and Na/sub 2/O. About 90% of the reserve base of US low-rank coal has less than one percent sulfur. Water resources in the major low-rank coal-bearing regions tend to have highly seasonal availabilities. Some areas appear to have ample water resources to support major new coal projects; in other areas such as Texas, water supplies may be constraining factor on development.

The behavior of catalysts in hydrogasification of sub-bituminous coal in pressured fluidized bed

International Nuclear Information System (INIS)

Yan, Shuai; Bi, Jicheng; Qu, Xuan

2017-01-01

Highlights: •CCHG in a pressured fluidized bed achieved 77.3 wt.% of CH 4 yield in 30 min. •Co-Ca and Ni-Ca triggered catalytic coal pyrolysis and char hydrogasification. •The reason for better catalytic performance of 5%Co-1%Ca was elucidated. •Sintered catalyst blocked the reactive sites and suppressed coal conversion. •Co-Ca made the catalyzed coal char rich in mesopore structures and reactive sites. -- Abstract: The catalytic hydrogasification of the sub-bituminous coal was carried out in a lab-scale pressurized fluidized bed with the Co-Ca, Ni-Ca and Fe-Ca as catalysts at 850 °C and 3 MPa. The effect of different catalysts on the characteristics of gasification products was investigated, and the behavior of the catalysts was also explored by means of the X-ray diffraction (XRD), FT-Raman, Brunauer–Emmett–Teller (BET), etc. Experiment results showed that all the catalysts promoted the carbon conversion in the coal catalytic hydrogasification (CCHG), and the catalytic activity was in the order: 5%Co-1%Ca > 5%Ni-1%Ca > 5%Fe-1%Ca. Compared with the raw coal hydrogasification, the carbon conversion increased from 43.4 wt.% to 91.3 wt.%, and the CH 4 yield increased from 23.7 wt.% to 77.3 wt.% within 30 min after adding the 5%Co-1%Ca catalyst into the coal. Co-Ca and Ni-Ca possessed catalytic effect on both processes of pyrolysis of coal and hydrogasification of coal char in CCHG, by which the graphitization of the coal was suppressed and methane formation rate was significantly accelerated. Fe/Co/Ni-Ca could penetrate into the interior of coal during CCHG, making the catalytic production of CH 4 conduct in the pore structures. The activity difference of the catalysts was owing to the different ability of rupturing the amorphous C−C bonds in coal structure. The incomplete carbon conversion of the 5%Co-1%Ca loaded coal was due to the agglomeration of the catalyst and the blockage of the reactive sites by the sintered catalyst. This work will provide

Trace element affinities in two high-Ge coals from China

Energy Technology Data Exchange (ETDEWEB)

Jing Li; Xinguo Zhuang; Xavier Querol [China University of Geosciences, Wuhan (China). Faculty of Earth Resources

2011-01-15

The Lincang (Yunnan Province, Southwest China) and Wulantuga (Inner Mongolia, Northeast China) coal deposits are known because of the high-Ge content. These coals have also a high concentration of a number of other elements. To determine the mode of occurrence of the enriched elements in both coals, six density fractions from {lt} 1.43 to {gt} 2.8 g/cm{sup 3} were obtained from two representative samples using heavy-liquids. A number of peculiar geochemical patterns characterize these high-Ge coals. Thus, the results of the chemical analysis of these density fractions showed that both coals (very distant and of a different geological age) are highly enriched (compared with the usual worldwide coal concentration ranges) in Ge, As, Sb, W, Be, and Tl. This may be due to similar geochemistry of hydrothermal fluids influencing the Earth Crust in these regions of China. Moreover, Wulantuga coal (Early Cretaceous subbituminous coal) is also enriched in Ca, Mg, and Na, and Lincang coal (Neogene subbituminous coal) in K, Rb, Nb, Mo, Sn, Cs, and U. A group of elements consisting of Ge, W, B, Nb, and Sb mostly occur with an organic affinity in both coals. Additionally, Be, U, and Mo (and partially Mn and Zn) in Lincang, and Na and Mg in Wulantuga occur also with a major organic affinity. Both coals have sulfide-arsenide mineral assemblages (Fe, S, As, Sn, and Pb, and in addition to Tl, Ta, and Cs in the Lincang coal). The occurrence of Al, P, Li, Sc, Ti, V, Cr, and Zr in both coals, and Ba in Lincang, are associated with the mineral assemblage of silico-aluminates and minor heavy minerals. Furthermore, P, Na, Li, Sc, Ti, Ga, Rb, Zr, Cr, Ba, Th, and LREE (La, Ce, Pr, Nd, and Gd) in Lincang are associated with mineral assemblages of phosphates and minor heavy minerals. The two later mineral assemblages are derived from the occurrence of detrital minerals. 34 refs., 7 figs., 3 tabs.

Clean utilization of low-rank coals for low-cost power generation

International Nuclear Information System (INIS)

Sondreal, E.A.

1992-01-01

Despite the unique utilization problems of low-rank coals, the ten US steam electric plants having the lowest operating cost in 1990 were all fueled on either lignite or subbituminous coal. Ash deposition problems, which have been a major barrier to sustaining high load on US boilers burning high-sodium low-rank coals, have been substantially reduced by improvements in coal selection, boiler design, on-line cleaning, operating conditions, and additives. Advantages of low-rank coals in advanced systems are their noncaking behavior when heated, their high reactivity allowing more complete reaction at lower temperatures, and the low sulfur content of selected deposits. The principal barrier issues are the high-temperature behavior of ash and volatile alkali derived from the coal-bound sodium found in some low-rank coals. Successful upgrading of low-rank coals requires that the product be both stable and suitable for end use in conventional and advanced systems. Coal-water fuel produced by hydrothermal processing of high-moisture low-rank coal meets these criteria, whereas most dry products from drying or carbonizing in hot gas tend to create dust and spontaneous ignition problems unless coated, agglomerated, briquetted, or afforded special handling

Rosebud SynCoal Partnership, SynCoal{reg_sign} demonstration technology update

Energy Technology Data Exchange (ETDEWEB)

Sheldon, R.W. [Rosebud SynCoal Partnership, Billings, MT (United States)

1997-12-31

An Advanced Coal Conversion Process (ACCP) technology being demonstrated in eastern Montana (USA) at the heart of one of the world`s largest coal deposits is providing evidence that the molecular structure of low-rank coals can be altered successfully to produce a unique product for a variety of utility and industrial applications. The product is called SynCoal{reg_sign} and the process has been developed by the Rosebud SynCoal Partnership (RSCP) through the US Department of Energy`s multi-million dollar Clean Coal Technology Program. The ACCP demonstration process uses low-pressure, superheated gases to process coal in vibrating fluidized beds. Two vibratory fluidized processing stages are used to heat and convert the coal. This is followed by a water spray quench and a vibratory fluidized stage to cool the coal. Pneumatic separators remove the solid impurities from the dried coal. There are three major steps to the SynCoal{reg_sign} process: (1) thermal treatment of the coal in an inert atmosphere, (2) inert gas cooling of the hot coal, and (3) removal of ash minerals. When operated continuously, the demonstration plant produces over 1,000 tons per day (up to 300,000 tons per year) of SynCoal{reg_sign} with a 2% moisture content, approximately 11,800b Btu/lb and less than 1.0 pound of SO{sub 2} per million Btu. This product is obtained from Rosebud Mine sub-bituminous coal which starts with 25% moisture, 8,600 Btu/lb and approximately 1.6 pounds of SO{sub 2} per million Btu.

Ignition behaviour of different rank coals in an entrained flow reactor

Energy Technology Data Exchange (ETDEWEB)

J. Faundez; A. Arenillas; F. Rubiera; X. Garcia; A.L. Gordon; J.J. Pis [Instituto Nacional del Carbon (INCAR), Oviedo (Spain)

2005-12-01

An experimental study to determine the temperature and mechanism of coal ignition was carried out by using an entrained flow reactor (EFR) at relatively high coal feed rates (0.5 g min{sup -1}). Seven coals ranging in rank from subbituminous to semianthracite, were tested and the evolved gases (O{sub 2}, CO, CO{sub 2}, NO) were measured continuously. The ignition temperature was evaluated from the gas evolution profiles, and it was found to be inversely correlated to the reactivity of the coal, as reflected by the increasing values of the ignition temperature in the sequence: subbituminous, high volatile bituminous, low volatile bituminous and semianthracite coals. The mechanism of ignition varied from a heterogeneous mechanism for subbituminous, low volatile bituminous and semianthracite coals, to a homogeneous mechanism for high volatile bituminous coals. A thermogravimetric analyser (TGA) was also used to evaluate coal ignition behaviour. Both methods, TGA and EFR, were in agreement as regards the mechanism of coal ignition. From the SEM micrographs of the coal particles retrieved from the cyclone, it was possible to observe the external appearance of the particles before, during and after ignition. The micrographs confirmed the mechanism deduced from the gas profiles. 23 refs., 5 figs., 1 tab.

On-line determination of moisture in coal and coke

International Nuclear Information System (INIS)

Cutmore, N.G.; Sowerby, B.D.

1987-01-01

The CSIRO Division of Mineral Engineering is developing various techniques for the on-line determination of moisture in coal and coke, and some instruments are now commercially available. These techniques permit accurate and rapid determination of moisture in materials directly on conveyor belts or in bins. The most promising techniques for direct on-belt measurement of moisture in coal are capacitance and microwave transmission. A non-contacting under-belt capacitance and gamma-ray backscatter technique has determined moisture in coal to better than 0.5 wt% in field tests. CSIRO is developing a fast neutron and gamma-ray transmission technique, which is proving very accurate in laboratory tests. This technique overcomes many of the limitations of thermal neutrons moisture gauges

Preliminary reservoir model of enhanced coalbed methane (ECBM) in a subbituminous coal seam, Huntly Coalfield, New Zealand

Energy Technology Data Exchange (ETDEWEB)

Zarrouk, Sadiq J. [Department of Engineering Science, University of Auckland, Private Bag 92019, Auckland (New Zealand); Moore, Tim A. [Solid Energy New Zealand Ltd, PO Box. 1303, Christchurch (New Zealand)]|[Department of Geological Sciences, University of Canterbury, Christchurch (New Zealand)

2009-01-07

The Huntly coalfield has significant coal deposits that contain biogenically-sourced methane. The coals are subbituminous in rank and Eocene in age and have been previously characterised with relatively low to moderate measured gas (CH{sub 4}) contents (2-4 m{sup 3}/ton). The CO{sub 2} holding capacity is relatively high (18.0 m{sup 3}/ton) compared with that of CH{sub 4} (2.6 m{sup 3}/ton) and N{sub 2} (0.7 m{sup 3}/ton) at the same pressure (4 MPa; all as received basis). The geothermal gradient is also quite high at 55 C/km. A study has been conducted which simulates enhancement of methane recovery (ECBM) from these deposits using a new version of the TOUGH2 (version 2) reservoir simulator (ECBM-TOUGH2) that can handle non-isothermal, multi-phase flows of mixtures of water, CH{sub 4}, CO{sub 2} and N{sub 2}. The initial phase of the simulation is CH{sub 4} production for the first 5 years of the field history. The model indicates that methane production can be significantly improved (from less than 80% recovery to nearly 90%) through injection of CO{sub 2}. However, although an increase in the rate of CO{sub 2} injection increases the amount of CO{sub 2} sequestered, the methane recovery (because of earlier breakthrough with increasing injection rate) decreases. Modeling of pure N{sub 2} injection produced little enhanced CH{sub 4} production. The injection of a hypothetical flue gas mixture (CO{sub 2} and N{sub 2}) also produced little increase in CH{sub 4} production. This is related to the low adsorption capacity of the Huntly coal to N{sub 2} which results in almost instantaneous breakthrough into the production well. (author)

Relationships between coal-quality and organic-geochemical parameters: A case study of the Hafik coal deposits (Sivas Basin, Turkey)

Energy Technology Data Exchange (ETDEWEB)

Erik, N. Yalcin; Sancar, S. [Cumhuriyet University, Department of Geological Engineering, Sivas (Turkey)

2010-09-01

This study provides coal-quality, organic-petrographic and organic-geochemical data on Tertiary subbituminous coal of the Hafik area, northwestern part of the Sivas Basin, Turkey. Coal-petrological studies along with proximate and ultimate analyses were undertaken to determine the organic-petrographic characteristics of the Hafik coals. Huminite reflectances were found to be between 0.38 and 0.48% (corresponding to an organic-material-rich and coal layers), values characteristic of low maturity. This parameter shows a good correlation with calorific values (average 21,060 kJ/kg) and average T{sub max} (422 C) mineral-matter diagenesis, indicating immaturity. The studied coals and organic material underwent only low-grade transformation, a consequence of low lithostatic pressure. Therefore, the Hafik coals are actually subbituminous in rank. Rock-Eval analysis results show types II/III and III kerogens. The organic fraction of the coals is mostly comprised of humic-group macerals (gelinites), with small percentages derived from the inertinite and liptinite groups. In this study, organic-petrographic, organic-geochemical and coal quality data were compared. The Hafik deposit is a high-ash, high-sulfur coal. The mineral matter of the coals is comprised mainly of calcite and clay minerals. (author)

Desulfurization of organic sulfur from a subbituminous coal by electron-transfer process with K{sub 4}(Fe(CN){sub 6})

Energy Technology Data Exchange (ETDEWEB)

Dipu Borah [Pragjyotika J College, Titabar (India). Department of Chemistry

2006-02-01

The desulfurization reaction involving direct electron transfer from potassium ferrocyanide, K{sub 4}(Fe(CN){sub 6}), successfully removed organic sulfur from a subbituminous coal. The temperature variation of desulfurization revealed that increase of temperature enhanced the level of sulfur removal. Moreover, the desulfurization reaction was found to be dependent on the concentration of K{sub 4}(Fe(CN){sub 6}). Gradual increase in the concentration of K{sub 4}(Fe(CN){sub 6}) raised the magnitude of desulfurization, but at higher concentration the variation was not significant. The removal of organic sulfur from unoxidized coal slightly increased with reduced particle size. Desulfurization from oxidized coals (prepared by aerial oxidation) revealed a higher level of sulfur removal in comparison to unoxidized coal. Highest desulfurization of 36.4 wt % was obtained at 90{sup o}C and 0.1 M concentration of K{sub 4}(Fe(CN){sub 6}) in the 100-mesh size oxidized coal prepared at 200{sup o}C. Model sulfur compound study revealed that aliphatic types of sulfur compounds are primarily responsible for desulfurization. Because of higher stability, thiophene and condensed thiophene-type of compounds perhaps remained unaffected by the electron-transfer agent. Infrared study revealed the formation of oxidized sulfur compounds (sulfoxide, sulfone, sulfonic acid, etc.) in the oxidized coals. The desulfurization reaction in different systems is well-represented by the pseudo-first-order kinetic model. Application of the transition state theory indicated that the desulfurization reaction proceeds with the absorption of heat (endothermic reaction) and is nonspontaneous in nature. 53 refs., 6 figs., 3 tabs.

Nuclear assay of coal. Volume 4. Moisture determination in coal: survey of electromagnetic techniques. Final report

International Nuclear Information System (INIS)

Bevan, R.; Luckie, P.; Gozani, T.; Brown, D.R.; Bozorgmanesh, H.; Elias, E.

1979-01-01

This survey consists of two basic parts. The first consists of a survey of various non-nuclear moisture determination techniques. Three techniques are identified as promising for eventual on-line application with coal; these are the capacitance, microwave attenuation, and nuclear magnetic resonance (NMR) techniques. The second part is devoted to an in-depth analysis of these three techniques and the current extent to which they have been applied to coal. With a given coal type, accuracies of +- 1% absolute in moisture content are achievable with all three techniques. The accuracy of the two electromagnetic techniques has been demonstrated in the laboratory and on-line in coal burning plants, whereas only small samples have been analyzed with NMR. The current shortcoming of the simple electromagnetic techniques is the sensitivity of calibrations to physical parameters and coal type. NMR is currently limited by small sample sizes and non-rugged design. These findings are summarized and a list of manufacturers of moisture analyzers is given in the Appendix

Process for treating moisture laden coal fines

Science.gov (United States)

Davis, Burl E.; Henry, Raymond M.; Trivett, Gordon S.; Albaugh, Edgar W.

1993-01-01

A process is provided for making a free flowing granular product from moisture laden caked coal fines, such as wet cake, by mixing a water immiscible substance, such as oil, with the caked coal, preferably under low shear forces for a period of time sufficient to produce a plurality of free flowing granules. Each granule is preferably comprised of a dry appearing admixture of one or more coal particle, 2-50% by weight water and the water immiscible substance.

Determination of moisture content in hard coals using microwave meter

International Nuclear Information System (INIS)

Chrusciel, E.; Kopec, M.; Turek, B.

1989-01-01

The results of hard-coal moisture-content measurements, performed with the aid of the ZAM-WILMER microwave meter are presented. Over 80 ground coal samples, weighing 1.5 kg (approx.) each, were examined. The moisture content values ranged from 0 to 15 wt%, with the mean standard error being equal to 0.8 wt%. 5 refs., 2 figs., 1 tab. (author)

Explosions of coal powder in pressured process; Explosiones de Polvo de Carbon en Procesos a Presion

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

As continuation of the previous introductory work about explosions of coal under hyperbaric conditions and considering the higher risk of explosions repercution with pressure; it was decided to develop this ambitious project, taking into account the more extensive range of type of coals: since subbituminous coals through hard coal to anthracite. It has been considered also several type of sorbents as limestones and others. The main objective of the project is to define, by experimental way, the utilization conditions for a safety coal handling. Many variables have been analyzed: Coal characteristics and origin, type of limestones, oxygen. moisture, temperature, and pressure. Due the great project complexity it was necessary to build one especial installation for trails under high pressure, where it was possible to use all the big number of variable combinations. The main research result has been the development of a model which has the possibility to simulate and analyze the foreseeable performance of coals and sorbent blends, in order to avoid the exploitations using specific handling methods. (Author)

Speciation of arsenic in Canadian feed-coal and combustion by-products

Energy Technology Data Exchange (ETDEWEB)

F. Goodarzi; F.E. Huggins [Natural Resourses Canada (Canada). Geological Survey of Canada-Calgary Division

2003-07-01

It is important to determine the oxidation state of arsenic in coal and coal combustion products, as this is generally the single most critical factor determining the toxicity of this element towards humans. However, the same factor is also important for understanding the volatility and reactions of arsenic forms in combustion and their leachability and mobility in ash-disposal situations. In this work, XAFS spectroscopy has been used to examine the speciation of arsenic in Canadian subbituminous and bituminous feed-coals and their combustion products. The concentration of arsenic in the feed-coals varied from < 2 ppm for subbituminous to 54 ppm for bituminous coals. Significant differences were noted in how arsenic occurs in subbituminous and bituminous coals, but, although such differences might influence the initial volatility and reactions of arsenic during coal combustion, arsenic is found almost entirely in the less toxic As{sup 5+} oxidation state in combustion products from both types of coal. (Abstract only)

Determination of moisture in black coal using pulsed nuclear magnetic resonance spectrometry

International Nuclear Information System (INIS)

Cutmore, N.G.; Sowerby, B.D.; Lynch, L.J.; Webster, D.S.

1987-01-01

Pulsed nuclear magnetic resonance (n.m.r.) spectrometry was investigated as a technique for moisture determination in fine product coal from eight Australian coal washeries. Measurements were made on samples of diameter 8 and 12 mm and length 10 and 120 mm at frequencies from 6.5 to 60 MHz. The ratio of intensities of the water and coal components in the free-induction decay signal can be used to determine moisture to within approx. 0.4-0.7 wt% over the range 0-26 wt% moisture, independent of sample density. This accuracy is independent of particle size (up to 1 mm) and little affected by coal rank, sample length or n.m.r. frequency. (author)

Automatic coal sampling for thermoelectric power plants. Some remarks on moisture

Energy Technology Data Exchange (ETDEWEB)

Tanzi, M.

1983-06-01

The following topics are discussed: coal sampling and reference standards; coal moisture and sampling; main technical data of the coal sampling station built for the EWEL power plant in Brindisi, Italy.

CO2 Emission Factors for Coals

Directory of Open Access Journals (Sweden)

P. Orlović-Leko

2015-03-01

(calcite and siderite directly contribute CO2 when they decompose during coal combustion. Variations in the maceral content can also influence CO2 emissions; high inertinite contents increase CO2 emissions. Sulphur in coal reduces EF(CO2. Fuel analysis is very important when estimating greenhouse gas emissions and emission factors. In this preliminary study, based on the results of the fuel analysis, CO2 emission factors for coals and peat from Livno, B&H have been calculated. EF(CO2 is defined as the amount of carbon dioxide emission per unit net calorific values of the fuel. Net calorific value (the lower heating value corresponds to the heat produced by combustion where total water in the combustion products exists as water vapour. The EF(CO2 obtained for sub-bituminous coal, lignite and peat were: 98.7, 109.5, and 147.9 t TJ−1, respectively, which correspond to the following net calorific values: 20.6, 11.5 and 3.6 MJ kg−1. The heating value is generally known to increase with the increase in carbon content (this parameter is connected with the degree of coalification, coal age. The other indispensable parameters are hydrogen, which has a positive effect on the net calorific value, and oxygen and water which impact the net calorific value negatively. The differences in net calorific values can be explained in part by the difference of total moisture content among the different fuel types. The CO2 emission factors calculated in this study were compared with those of IPCC. A significant difference was observed for peat (39.5 %, followed by lignite (8.2 % and sub-bituminous coal (4.3 %.

Thermogravimetric analysis of the behavior of sub-bituminous coal and cellulosic ethanol residue during co-combustion.

Science.gov (United States)

Buratti, C; Barbanera, M; Bartocci, P; Fantozzi, F

2015-06-01

The influence of the addition of cellulosic ethanol residue (CER) on the combustion of Indonesian sub-bituminous coal was analyzed by non isothermal thermo-gravimetric analysis (TGA). The effect of blends ratio (5%, 10%, 15% and 20%), interaction mechanism, and heating rate (5°C/min, 10°C/min, 15°C/min, 20°C/min) on the combustion process was studied. The results show that the increase of the blending ratio allows to achieve the increase of the combustibility index from 7.49E-08 to 5.26E-07 at the blending ratio of 20%. Two types of non-isothermal kinetic analysis methods (Ozawa-Flynn-Wall and Vyazovkin) were also applied. Results indicate that the activation energy of the blends decreases with increasing the conversion rate. In particular, the blending ratio of 20% confirms to have the better combustion performance, with the average value of the activation energy equal to 41.10 kJ/mol obtained by Ozawa-Flynn-Wall model and 31.17 kJ/mol obtained by Vyazovkin model. Copyright © 2015 Elsevier Ltd. All rights reserved.

HIGH PRESSURE COAL COMBUSTON KINETICS PROJECT

Energy Technology Data Exchange (ETDEWEB)

Stefano Orsino

2005-03-30

As part of the U.S. Department of Energy (DoE) initiative to improve the efficiency of coal-fired power plants and reduce the pollution generated by these facilities, DOE has funded the High-Pressure Coal Combustion Kinetics (HPCCK) Projects. A series of laboratory experiments were conducted on selected pulverized coals at elevated pressures with the specific goals to provide new data for pressurized coal combustion that will help extend to high pressure and validate models for burnout, pollutant formation, and generate samples of solid combustion products for analyses to fill crucial gaps in knowledge of char morphology and fly ash formation. Two series of high-pressure coal combustion experiments were performed using SRI's pressurized radiant coal flow reactor. The first series of tests characterized the near burner flame zone (NBFZ). Three coals were tested, two high volatile bituminous (Pittsburgh No.8 and Illinois No.6), and one sub-bituminous (Powder River Basin), at pressures of 1, 2, and 3 MPa (10, 20, and 30 atm). The second series of experiments, which covered high-pressure burnout (HPBO) conditions, utilized a range of substantially longer combustion residence times to produce char burnout levels from 50% to 100%. The same three coals were tested at 1, 2, and 3 MPa, as well as at 0.2 MPa. Tests were also conducted on Pittsburgh No.8 coal in CO2 entrainment gas at 0.2, 1, and 2 MPa to begin establishing a database of experiments relevant to carbon sequestration techniques. The HPBO test series included use of an impactor-type particle sampler to measure the particle size distribution of fly ash produced under complete burnout conditions. The collected data have been interpreted with the help of CFD and detailed kinetics simulation to extend and validate devolatilization, char combustion and pollutant model at elevated pressure. A global NOX production sub-model has been proposed. The submodel reproduces the performance of the detailed chemical

Physicochemical Characterization and Thermal Decomposition of Garin Maiganga Coal

Directory of Open Access Journals (Sweden)

Nyakuma Bemgba Bevan

2016-12-01

Full Text Available The paper examined physicochemical and thermal characteristics of the newly discovered Garin Maiganga (GMG coal from Nigeria. The physicochemical characterization comprised of elemental, proximate, calorific value, and classification (rank analyses. Thermal analysis was examined using combined Thermogravimetric (TG and Derivative Thermogravimetric analyses (DTG. Hence, the coal was heated from 30°C to 1000°C at 20°C/min under inert conditions to examine its thermal degradation behaviour and temperature profile characteristics (TPC. The results indicated that the GMG coal fuel properties consist of low Ash, Nitrogen, and Sulphur content. Moisture content was > 5%, Volatile Matter > 50%, Fixed Carbon > 22%, and Heating Value (HHV 23.74 MJ/kg. Based on its fuel properties, the GMG coal can be classified as a Sub-Bituminous B, non-agglomerating low rank coal (LRC. The GMG coal TPCs – onset, peak, and offset temperatures – were 382.70°C, 454.60°C, and 527.80°C, respectively. The DTG profile revealed four (4 endothermic peaks corresponding to loss of moisture (drying, volatile matter (devolatization, and coke formation. The residual mass Rm was 50.16%, which indicates that higher temperatures above 1000°C are required for the complete pyrolytic decomposition of the GMG coal. In conclusion, the results indicate that the GMG coal is potentially suitable for future utilization in electric power generation and the manufacture of cement and steel.

Biotransformation of Spanish coals by microorganisms; Biotransformacion de Carbones Espanoles por Microorganismos

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

some newly isolated microorganisms could solubilized different kinds of Spanish coals (hard coal, subbituminous coal and lignite). Certain fungi and bacteria could solubilized lignite when growing in a mineral medium. However, to solubilized higher rank coals (hard coal and subbituminous coal) microorganisms require a complete medium. Microorganisms, which showed higher capacity to solubilized coal, were incubated in the presence of coal (hard coal, subbituminous coal and lignite) at the optimal conditions to get coal liquefaction/solubilization. The resultant products were analysed by IR and UV/visible spectrometry. No major differences among the original coal, solubilized/liquefied coal and residual coal were detected. However, an increase in metallic carboxylate and a decrease in OH'- carboxylic groups were observed in the liquefied lignite. Humic acids derived from original lignite residual lignite and liquefied/solubilized lignite by microorganisms were analysed. Several differences were observed in the humic acids extracted from the liquefied lignite, such as an increase in the total acidity and in the proportion of the phenolic groups. Differences on the humic acid molecular weight were observed too. Several fungal and bacterial strains were able to grow using humic acids as sole carbon source. Microorganisms growing in humic acid were observed by Scanning Electron Microscopy. Besides, the coal solubilization capacity of several fungal strains (M2, m$ and AGI) growing in different culture media was assayed. In order to get some insight into the mechanisms of the liquefaction/solubilization of Spanish coals (hard coal, subbituminous coal and lignite) by these microorganisms, some features in the culture supernatants were studied: pH values; extracellular specific proteins; enzyme activities possibly related with coal solubilization and the presence of oxalate. M2 and M4 fungal strains grown in the presence of coal produced some specific extracellular proteins

Biotransformation of Spanish coals by microorganisms; Biotransformacion de Carbones Espanoles por Microorganismos

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

some newly isolated microorganisms could solubilized different kinds of Spanish coals (hard coal, subbituminous coal and lignite). Certain fungi and bacteria could solubilized lignite when growing in a mineral medium. However, to solubilized higher rank coals (hard coal and subbituminous coal) microorganisms require a complete medium. Microorganisms, which showed higher capacity to solubilized coal, were incubated in the presence of coal (hard coal, subbituminous coal and lignite) at the optimal conditions to get coal liquefaction/solubilization. The resultant products were analysed by IR and UV/visible spectrometry. No major differences among the original coal, solubilized/liquefied coal and residual coal were detected. However, an increase in metallic carboxylate and a decrease in OH'- carboxylic groups were observed in the liquefied lignite. Humic acids derived from original lignite residual lignite and liquefied/solubilized lignite by microorganisms were analysed. Several differences were observed in the humic acids extracted from the liquefied lignite, such as an increase in the total acidity and in the proportion of the phenolic groups. Differences on the humic acid molecular weight were observed too. Several fungal and bacterial strains were able to grow using humic acids as sole carbon source. Microorganisms growing in humic acid were observed by Scanning Electron Microscopy. Besides, the coal solubilization capacity of several fungal strains (M2, m$ and AGI) growing in different culture media was assayed. In order to get some insight into the mechanisms of the liquefaction/solubilization of Spanish coals (hard coal, subbituminous coal and lignite) by these microorganisms, some features in the culture supernatants were studied: pH values; extracellular specific proteins; enzyme activities possibly related with coal solubilization and the presence of oxalate. M2 and M4 fungal strains grown in the presence of coal produced some specific extracellular

Effect of moisture content on the R{sub 70} self-heating rate of Callide coal

Energy Technology Data Exchange (ETDEWEB)

Beamish, B. Basil; Hamilton, Garth R. [School of Engineering, The University of Queensland, St Lucia, Qld 4072 (Australia)

2005-10-17

Strip samples from the Boundary Hill pit at Callide have been tested in an adiabatic oven to assess the effect of moisture on the R{sub 70} self-heating rate of coal. The two strip samples tested had R{sub 70} self-heating rate values of 10.23 and 8.61 {sup o}C/h. As the moisture content of the coal was progressively increased, from the dry state of the test, the R{sub 70} value decreased dramatically. At approximately 40-50% of the moisture holding capacity of the coal, the self-heating rate becomes measurable. Above this critical level of moisture content, the heat produced by oxidation is dissipated by moisture evaporation and coal self-heating is significantly delayed. (author)

Greenhouse gas emission factor development for coal-fired power plants in Korea

International Nuclear Information System (INIS)

Jeon, Eui-Chan; Myeong, Soojeong; Sa, Jae-Whan; Kim, Jinsu; Jeong, Jae-Hak

2010-01-01

Accurate estimation of greenhouse gas emissions is essential for developing an appropriate strategy to mitigate global warming. This study examined the characteristics of greenhouse gas emission from power plants, a major greenhouse gas source in Korea. The power plants examined use bituminous coal, anthracite, and sub-bituminous coal as fuel. The CO 2 concentration from power plants was measured using GC-FID with methanizer. The amount of carbon, hydrogen, and calorific values in the input fuel was measured using an elemental analyzer and calorimeter. For fuel analysis, CO 2 emission factors for anthracite, bituminous coal, and sub-bituminous coal were 108.9, 88.4, and 97.9 Mg/kJ, respectively. The emission factors developed in this study were compared with those for IPCC. The results showed that CO 2 emission was 10.8% higher for anthracite, 5.5% lower for bituminous coal, and 1.9% higher for sub-bituminous coal than the IPCC figures.

Mode of occurrence of chromium in four US coals

Science.gov (United States)

Huggins, Frank E.; Shah, N.; Huffman, G.P.; Kolker, A.; Crowley, S.; Palmer, C.A.; Finkelman, R.B.

2000-01-01

The mode of occurrence of chromium in three US bituminous coals and one US subbituminous has been examined using both X-ray absorption fine structure (XAFS) spectroscopy and a selective leaching protocol supplemented by scanning electron microscopy (SEM) and electron microprobe measurements. A synthesis of results from both methods indicates that chromium occurs principally in two forms in the bituminous coals: the major occurrence of chromium is associated with the macerals and is not readily leached by any reagent, whereas a second, lesser occurrence, which is leachable in hydrofluoric acid (HF), is associated with the clay mineral, illite. The former occurrence is believed to be a small particle oxyhydroxide phase (CrO(OH)). One coal also contained a small fraction (<5%) of the chromium in the form of a chromian magnetite, and the leaching protocol indicated the possibility of a similar small fraction of chromium in sulfide form in all three coals. There was little agreement between the two techniques on the mode of occurrence of chromium in the subbituminous coal; however, only a limited number of subbituminous coals have been analyzed by either technique. The chromium in all four coals was trivalent as no evidence was found for the Cr6+ oxidation state in any coal.

Impacts of halogen additions on mercury oxidation, in a slipstream selective catalyst reduction (SCR), reactor when burning sub-bituminous coal.

Science.gov (United States)

Cao, Yan; Gao, Zhengyang; Zhu, Jiashun; Wang, Quanhai; Huang, Yaji; Chiu, Chengchung; Parker, Bruce; Chu, Paul; Pant, Wei-Ping

2008-01-01

This paper presents a comparison of impacts of halogen species on the elemental mercury (Hg(0)) oxidation in a real coal-derived flue gas atmosphere. It is reported there is a higher percentage of Hg(0) in the flue gas when burning sub-bituminous coal (herein Powder River Basin (PRB) coal) and lignite, even with the use of selective catalytic reduction (SCR). The higher Hg(0)concentration in the flue gas makes it difficult to use the wet-FGD process for the mercury emission control in coal-fired utility boilers. Investigation of enhanced Hg(0) oxidation by addition of hydrogen halogens (HF, HCl, HBr, and HI) was conducted in a slipstream reactor with and without SCR catalysts when burning PRB coal. Two commercial SCR catalysts were evaluated. SCR catalyst no. 1 showed higher efficiencies of both NO reduction and Hg(0) oxidation than those of SCR catalyst no. 2. NH3 addition seemed to inhibit the Hg(0) oxidation, which indicated competitive processes between NH3 reduction and Hg(0) oxidation on the surface of SCR catalysts. The hydrogen halogens, in the order of impact on Hg(0) oxidation, were HBr, HI, and HCl or HF. Addition of HBr at approximately 3 ppm could achieve 80% Hg(0) oxidation. Addition of HI at approximately 5 ppm could achieve 40% Hg(0) oxidation. In comparison to the empty reactor, 40% Hg(0) oxidation could be achieved when HCl addition was up to 300 ppm. The enhanced Hg(0) oxidation by addition of HBr and HI seemed not to be correlated to the catalytic effects by both evaluated SCR catalysts. The effectiveness of conversion of hydrogen halogens to halogen molecules or interhalogens seemed to be attributed to their impacts on Hg(0) oxidation.

Determination of moisture in coal, in the case of discontinuous transport, using condensers

Energy Technology Data Exchange (ETDEWEB)

Prieto-Fernandez, Ismael; Luengo-Garcia, Juan-Carlos; Alonso, Manuela [Area Maquinas y Motores Termicos, Universidad de Oviedo, Campus Universitario, 33203 , Asturias Gijon (Spain)

2002-02-20

The need for a rapid method of determining the technological characteristics of coal has been increasing in the last decades. The coal industry demands methods of coal analysis on a rapid and reasonably accurate basis. In this report, a non-conventional system for moisture analysis of thermal coal, based on capacitance techniques, is proposed. A device for non-continuous analysis based on this technique is designed and developed. Such device simulates a cylindrical condenser, in which coal acts as the dielectric material. The device is used to measure moisture content in coals. The results from the statistical analyses and conclusions are presented. Also, on-site potential use of capacitance techniques is shown.

Organic petrology of subbituminous carbonaceous shale samples from Chalaw, Kabul Province, Afghanistan: Considerations for paleoenvironment and energy resource potential

Energy Technology Data Exchange (ETDEWEB)

Hackley, Paul C.; SanFilipo, John R. [U.S. Geological Survey, MS 956 National Center, Reston VA, 20192 (United States); Azizi, Gul Pacha [Afghanistan Geological Survey, Macroryan Square, Kabul (Afghanistan); Davis, Philip A. [U.S. Geological Survey, 520 N. Park Avenue, Tucson AZ, 85719 (United States); Starratt, Scott W. [U.S. Geological Survey, MS 910, 345 Middlefield Rd, Menlo Park CA, 94025 (United States)

2010-04-01

Neogene (?) subbituminous carbonaceous shale deposits from Chalaw, Afghanistan, were investigated through organic petrology techniques and standard coal analyses to determine paleoenvironment and potential for resource utilization. The Chalaw deposit, approximately 30 km southeast of Kabul, currently is exploited for brick making and domestic heating and cooking. Three multiple-bench channel samples of the mined bed at Chalaw were collected and evaluated. The presence of significant huminite (ranging from 0.2 to 59.0 vol.%, mineral-inclusive basis) is suggestive of a terrestrial lignin-rich precursor plant material. Measured reflectance values of 0.38-0.55% indicate subbituminous rank. This rank suggests burial depths of approximately 1500 m and maximum temperatures of approximately 50 C. Structured liptinite macerals generally are absent except for some fluorescing morphologies interpreted to be poorly-preserved root cork suberinite. Sponge spicule bioliths including gemmoscleres and megascleres are common. These petrographic observations, in addition to high mineral matter content (33 to > 95 vol.%), medium to high sulfur content (2.1-11.5 wt.%, dry basis; db), and the presence of common gastropod? shell fragments and an aragonite-needle chalk bed are consistent with, but not directly indicative of, a marginal marine or estuarine mangrove depositional environment. However, additional data are necessary to confirm this hypothesis and deposition in a freshwater environment cannot be ruled out at this time. Commercial-scale development and utilization of the Chalaw deposit as a thermal fuel resource may be possible using a fluidized bed combustion system which could accept the low-quality mine product currently produced. Samples examined herein contain high-ash yield (45-90 wt.%, db), high total moisture content (17-39 wt.%), low calorific value (980-6860 Btu/lb, m,mmf), and have poor agglomerating properties (FSI = 0), consistent with fuels utilized in fluidized

Australian black coal statistics 1991

Energy Technology Data Exchange (ETDEWEB)

1992-01-01

This third edition of Australian black coal statistics covers anthracite, bituminous and subbituminous coals. It includes maps and figures on resources and coal fields and statistics (mainly based on the calendar year 1991) on coal demand and supply, production, employment and productivity in Australian coal mines, exports, prices and ports, and domestic consumption. A listing of coal producers by state is included. A final section presents key statistics on international world trade in 1991. 54 tabs.

γ-ray activity in bituminous, subbituminous and lignite coals

International Nuclear Information System (INIS)

Barber, D.E.; Giorgio, H.R.

1977-01-01

Specimens of three different types of coal from four different geographical locations (Montana, North Dakota, Illinois and Pennsylvania) were examined by γ-ray spectrometry. Some samples were ashed in a muffle furnace. Other samples included pulverized coal, slag and fly ash from an electric power generating station. Activity from the 232 Th and 238 U series was present in all samples. Activity varied widely depending upon the source of the coal. The results indicate a need for additional examination of activity in coal to: (1) establish more precisely the relative environmental impact of coal-fired power stations compared with nuclear ones, (2) indicate the degree of sophistication required in environmental surveillance programs involving areas where both nuclear and coal-fired power stations are operational, and (3) determine the occupational exposure risks in mining operations. (author)

MCNP simulation of the influence of the external moisture on low calorific value in the coal quality analysis by neutron

International Nuclear Information System (INIS)

Liu Dekun; Zhang Hongyu; Zhang Lihong; Dong Huan; Gu Deshan

2012-01-01

An important index in assessment of coal quality is low calorific value. Using neutron to analysis coal quality, the more the coal moisture content, especially the increasing of external moisture will reduce the low calorific value. The principle of coal quality analysis by neutron prompt Gamma-ray is introduced. The influence of the gamma count of the carbon element peak with increasing external moisture in coal samples was simulated using MCNP code. And discussed the reasons how external moisture content influence the calorific value. Simulation results indicate that with the increasing of external moisture in the coal samples, the gamma count of the carbon element peak dwindling, and the low calorific value reducing. The conclusion is : using neutrons method to analysis coal quality, the more external moisture content, the larger error of the measurement results of the carbon element, and will influence the calculation accuracy of the low calorific value. (authors)

Flash hydropyrolysis of coal using a small scale of free fall reactor

Energy Technology Data Exchange (ETDEWEB)

Miura, K.; Morozumi, F. [Kyoto University, Kyoto (Japan). Department of Chemical Engineering

1998-07-01

A small scale of high-pressure free fall reactor was developed for the flash hydropyrolysis of coal. Taiheiyo coal (a Japanese subbituminous coal) was pyrolysed under a high hydrogen pressure without difficulty by use of this reactor. The effect of gas atmosphere, residence time, pressure, and temperature on the product yield was examined in detail. A flash hydropyrolysis reaction model was developed based on the experimental data, and its validity was examined. 8 refs., 5 figs., 1 tab.

A comparison of spontaneous combustion susceptibility of coal from ...

African Journals Online (AJOL)

Although the CPT of Onyeama coal and Owukpa coal is identical to each other as they are the sub-bituminous, Owukpa coal has a lower initial oxidation temperature (IOT) and maximum oxidation temperature (MOT) than those of Onyeama coal. This means that although each coal has the same rank and CPT, spontaneous ...

Demonstration of the Viability and Evaluation of Production Costs for Biomass-Infused Coal Briquettes

Energy Technology Data Exchange (ETDEWEB)

Kamshad, Kourosh [Coaltek Incorporated, Tucker, GA (United States)

2014-04-01

This project was split into four main areas, first to identify the best combination of coal and biomass, second, create and test lab quantity of preferred combinations, Third, create a sizeable quantity for larger scale handling and consuming analysis and fourth, to provide analysis for a commercial scale production capacity. Samples of coal and biomass were collected. Five coals, representing the three major coal ranks, were collected including one bituminous, two sub-bituminous, and two lignite samples. In addition, three square bales (~50 lbs/bale) each of corn Stover and switch grass were collected with one bale of each sample processed through a hammer mill to approximately -5 mesh. A third sample of sawdust was collected once experimentation began at the University of Kentucky. Multiple combinations of coal and biomass; coal, biomass, with biomass binder, were tested until a formulation was identified that could meet the requirement criteria. Based on the results of the binderless briquetting evaluations, the CS/Sub-bit combinations was selected for extended evaluation at a 10% biomass addition rate while the WS/Bitum combination was selected for extended evaluation at a 30% biomass-addition rate. With the final results of the selection process complete, the CoalTek continuous production pilot plant in Tucker GA was outfitted with the specialized blending equipment and two 1/4 ton production runs of biomass and binder subbituminous coal briquettes were completed. These briquettes were later used for a calorific test burn at the University of North Dakota. The first formulation included subbituminous coal, corn stover and a corn starch binder the second formulation included subbituminous coal, wheat stover and corn starch binder.

Thermal stability of carboxylic acid functionality in coal; Sekitanchu ni sonzaisuru karubokishiruki no netsubunkai kyodo

Energy Technology Data Exchange (ETDEWEB)

Tsutsumi, Y.; Aida, T. [Kinki University, Osaka (Japan). Faculty of Engineering

1996-10-28

Carboxyl in coal was focused in discussing its pyrolytic behavior while tracking change of its absolute amount relative to the heating temperatures. A total of four kinds of coals, consisting of two kinds brown coals, sub-bituminous coal and bituminous coal were used. Change in the absolute amount of carboxyl due to heating varies with coalification degree. Decomposition starts in the bituminous coal from around 300{degree}C, and is rapidly accelerated when 400{degree}C is exceeded. Carboxyls in brown coals exist two to three times as much as those in bituminous and sub-bituminous coals, of which 40% is decomposed at a temperature as low as about 300{degree}C. Their pyrolytic behavior at temperatures higher than 400{degree}C resembles that of the bituminous coal. Carboxyls consist of those easy to decompose and difficult to decompose. Aromatic and aliphatic carboxylic acids with simple structure are stable at temperatures lower than 300{degree}C, and decompose abruptly from about 400{degree}C, hence their behavior resembles that of carboxyls in bituminous and sub-bituminous coals. Structure of low-temperature decomposing carboxyls in brown coals is not known, but it is assumed that humic acid originated from natural materials remains in the structure. 4 refs., 3 figs., 1 tab.

Adjustments of microwave-based measurements on coal moisture using natural radioactivity techniques

Energy Technology Data Exchange (ETDEWEB)

Prieto-Fernandez, I.; Luengo-Garcia, J.C.; Alonso-Hidalgo, M.; Folgueras-Diaz, B. [University of Oviedo, Gijon (Spain)

2006-01-07

The use of nonconventional on-line measurements of moisture and ash content in coal is presented. The background research is briefly reviewed. The possibilities of adjusting microwave-based moisture measurements using natural radioactive techniques, and vice versa, are proposed. The results obtained from the simultaneous analysis of moisture and ash content as well as the correlation improvements are shown.

Extreme coal handling

Energy Technology Data Exchange (ETDEWEB)

Bradbury, S; Homleid, D. [Air Control Science Inc. (United States)

2004-04-01

Within the journals 'Focus on O & M' is a short article describing modifications to coal handling systems at Eielson Air Force Base near Fairbanks, Alaska, which is supplied with power and heat from a subbituminous coal-fired central plant. Measures to reduce dust include addition of an enclosed recirculation chamber at each transfer point and new chute designs to reduce coal velocity, turbulence, and induced air. The modifications were developed by Air Control Science (ACS). 7 figs., 1 tab.

Automatic coal sampling for thermoelectric power plants; some remarks on moisture

Energy Technology Data Exchange (ETDEWEB)

Tanzi, M.

1983-06-01

Some problems associated with automatic coal sampling are discussed, in particular the change in moisture content during transport to sampling station. The moisture level is reduced by crushing and air exposure. Possible solutions to the problems are outlined: reducing exposure to air; reducing the degree of pulverisation; and use of special crushing equipment.

Report on the coal type committee meetings in fiscal 1988; 1989 nendo tanshu iinkai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-03-01

This paper is a report on the coal type committee meetings in fiscal 1988. It summarizes the report mainly on the data distributed at the first and second coal type committee meetings. It describes liquefaction performance tests on Chinese coals in the coal type selection and investigation. In order to develop jointly by Japan and China the coal liquefaction technology, liquefaction tests have been performed on Chinese coals since fiscal 1982 by using the small continuous testing equipment (0.1 t/d) installed in the Beijing Soot and Coal Science Research Institute. The test is now in the third phase. The first sub-committee meeting reported the result on the Shenmu Simengou coal. The coal type investigation has analyzed coal samples collected from the world, classified them into brown coal, sub-bituminous coal of low coal rank, sub-bituminous coal, highly volatile bituminous coal of low coal rank, and highly volatile bituminous coal, and presented a list of candidate coals for liquefaction. Regarding the liquefaction performance tests on Chinese coals, the second coal type committee meeting reported the result on the Fuxin Qinghemen coal, and the result on the Tianzhu coal as revealed by using the NEDOL process BSU. The paper also presents the interim report on the research achievements in fiscal 1988 on the liquefaction performance tests on Chinese coals and the research achievements of the investigation and study in fiscal 1988 on the treatment technologies for coals used for coal gasification 'coal type selection and investigation'. (NEDO)

Report on the coal type committee meetings in fiscal 1988; 1989 nendo tanshu iinkai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-03-01

This paper is a report on the coal type committee meetings in fiscal 1988. It summarizes the report mainly on the data distributed at the first and second coal type committee meetings. It describes liquefaction performance tests on Chinese coals in the coal type selection and investigation. In order to develop jointly by Japan and China the coal liquefaction technology, liquefaction tests have been performed on Chinese coals since fiscal 1982 by using the small continuous testing equipment (0.1 t/d) installed in the Beijing Soot and Coal Science Research Institute. The test is now in the third phase. The first sub-committee meeting reported the result on the Shenmu Simengou coal. The coal type investigation has analyzed coal samples collected from the world, classified them into brown coal, sub-bituminous coal of low coal rank, sub-bituminous coal, highly volatile bituminous coal of low coal rank, and highly volatile bituminous coal, and presented a list of candidate coals for liquefaction. Regarding the liquefaction performance tests on Chinese coals, the second coal type committee meeting reported the result on the Fuxin Qinghemen coal, and the result on the Tianzhu coal as revealed by using the NEDOL process BSU. The paper also presents the interim report on the research achievements in fiscal 1988 on the liquefaction performance tests on Chinese coals and the research achievements of the investigation and study in fiscal 1988 on the treatment technologies for coals used for coal gasification 'coal type selection and investigation'. (NEDO)

Characterising the combustion behaviour of New Zealand coals by thermogravimetry

Energy Technology Data Exchange (ETDEWEB)

Benfell, K.E.; Beamish, B.B.; Rodgers, K.A. [University of Auckland, Auckland (New Zealand). Dept. of Geology

1995-12-31

Thirty-three New Zealand coals were subjected to thermogravimetric analysis (TG) and derivative thermogravimetric analysis (DTG) to evaluate the techniques` applicability to New Zealand coals. Generally, New Zealand sub-bituminous coals have lower burnout temperatures than bituminous coals. However, local and regional differences occur, where some sub-bituminous coals show both higher and lower char burnout temperatures than may be otherwise expected from their rank and T{sub 6} values (the peak temperature where the rate of weight loss of the sample is the greatest). There is a sizeable variations in the char burnout temperature (T{sub 8}) (465 to 636{degree}C) in coals with volatile matter contents above 40%, whereas coals with lower volatile contents have T{sub 8} values around 646{degree}C. The temperature of char burnout gives a better indication of combustion efficiency than rank or volatile matter content alone. Industrial operators could use this technique to provide an indication of burnout performance before a coal is purchased, assisting evaluation of the coal`s suitability for a particular usage. 10 refs., 4 figs., 3 tabs.

Process and analytical studies of enhanced low severity co-processing using selective coal pretreatment

Energy Technology Data Exchange (ETDEWEB)

Baldwin, R.M.; Miller, R.L.

1991-12-01

The findings in the first phase were as follows: 1. Both reductive (non-selective) alkylation and selective oxygen alkylation brought about an increase in liquefaction reactivity for both coals. 2. Selective oxygen alkylation is more effective in enhancing the reactivity of low rank coals. In the second phase of studies, the major findings were as follows: 1. Liquefaction reactivity increases with increasing level of alkylation for both hydroliquefaction and co-processing reaction conditions. 2. the increase in reactivity found for O-alkylated Wyodak subbituminous coal is caused by chemical changes at phenolic and carboxylic functional sites. 3. O-methylation of Wyodak subbituminous coal reduced the apparent activation energy for liquefaction of this coal.

Alkaloid-derived molecules in low rank Argonne premium coals.

Energy Technology Data Exchange (ETDEWEB)

Winans, R. E.; Tomczyk, N. A.; Hunt, J. E.

2000-11-30

Molecules that are probably derived from alkaloids have been found in the extracts of the subbituminous and lignite Argonne Premium Coals. High resolution mass spectrometry (HRMS) and liquid chromatography mass spectrometry (LCMS) have been used to characterize pyridine and supercritical extracts. The supercritical extraction used an approach that has been successful for extracting alkaloids from natural products. The first indication that there might be these natural products in coals was the large number of molecules found containing multiple nitrogen and oxygen heteroatoms. These molecules are much less abundant in bituminous coals and absent in the higher rank coals.

Effect of flotation on preparation of coal-water slurries

Energy Technology Data Exchange (ETDEWEB)

Ding, K.; Laskowski, J.S. [University of British Columbia, Vancouver, BC (Canada)

2009-07-01

In order to study the effect of flotation reagents on the properties of coal-water slurry, a sub-bituminous coal was cleaned via either forward flotation or reverse flotation. The froth product from the forward flotation, obtained with the use of diesel oil and MIBC, and the tailings of the reverse flotation, carried out with dextrin-tannic acid depressants and dodecyltrimethylammonium chloride collector, were used in the preparation of coal-water slurries. It was shown that while it was possible to obtain the coal-water slurry with a high-solids content from the coal rendered hydrophilic (tailings from the coal reverse flotation), in the case of the hydrophobic product (froth product from the forward flotation) a dispersing agent was required to obtain the coal-water slurry of the same high-solids content.

Development of upgraded brown coal process

Energy Technology Data Exchange (ETDEWEB)

Komatsu, N.; Sugita, S.; Deguchi, T.; Shigehisa, T.; Makino, E. [Kobe Steel Ltd., Hyogo (Japan). Coal and Energy Project Department

2004-07-01

Half of the world's coal resources are so-called low rank coal (LRC) such as lignite, subbituminous coal. Utilization of such coal is limited due to low heat value and high propensity of spontaneous combustion. Since some of LRCs have advantages as clean coal, i.e. low ash and low sulfur content, LRC can be the excellent feedstock for power generation and metallurgy depending on the upgrading technology. The UBC (upgraded brown coal) process introduced here converts LRC to solid fuel with high heat value and less propensity of self-heating. Various world coals, such as Australian, Indonesian and USA LRC, were tested using the Autoclave and Bench Scale Unit, and the process application to LRC of wide range is proven. The R & D activities of the UBC process are introduced including a demonstration project with a 5 ton/day test plant in progress in Indonesia, expecting near future commercialisation in order to utilize abundant LRC of clean properties. 8 refs., 12 figs., 3 tabs.

Conversion of metallurgical coke and coal using a Coal Direct Chemical Looping (CDCL) moving bed reactor

International Nuclear Information System (INIS)

Luo, Siwei; Bayham, Samuel; Zeng, Liang; McGiveron, Omar; Chung, Elena; Majumder, Ankita; Fan, Liang-Shih

2014-01-01

Highlights: • Accumulated more than 300 operation hours were accomplished for the moving bed reducer reactor. • Different reactor operation variables were investigated with optimal conditions identified. • High conversions of sub-bituminous coal and bituminous coal were achieved without flow problems. • Co-current and counter-current contact modes were tested and their applicability was discussed. - Abstract: The CLC process has the potential to be a transformative commercial technology for a carbon-constrained economy. The Ohio State University Coal Direct Chemical Looping (CDCL) process directly converts coal, eliminating the need for a coal gasifier oran air separation unit (ASU). Compared to other solid-fuel CLC processes, the CDCL process is unique in that it consists of a countercurrent moving bed reducer reactor. In the proposed process, coal is injected into the middle of the moving bed, whereby the coal quickly heats up and devolatilizes, splitting the reactor roughly into two sections with no axial mixing. The top section consists of gaseous fuel produced from the coal volatiles, and the bottom section consists of the coal char mixed with the oxygen carrier. A bench-scale moving bed reactor was used to study the coal conversion with CO 2 as the enhancing gas. Initial tests using metallurgical cokefines as feedstock were conducted to test the effects of operational variables in the bottom section of the moving bed reducer, e.g., reactor temperature, oxygen carrier to char ratio, enhancer gas CO 2 flow rate, and oxygen carrier flow rates. Experiments directly using coal as the feedstock were subsequently carried out based on these test results. Powder River Basin (PRB) coal and Illinois #6 coal were tested as representative sub-bituminous and bituminous coals, respectively. Nearly complete coal conversion was achieved using composite iron oxide particles as the oxygen carriers without any flow problems. The operational results demonstrated that a

XRD and FT–IR investigations of sub-bituminous Assam coals

Indian Academy of Sciences (India)

TECS

extremely difficult and therefore, research on coal structure is still a ... the basis of development of spectroscopic methods. These are FTIR ... such as natural gas or imported coals to satisfy the energy requirement .... A new computer program in C++ was developed .... tool for characterization of coal and its products as it fur-.

Wyoming coal-conversion project. Final technical report, November 1980-February 1982. [Proposed WyCoalGas project, Converse County, Wyoming; contains list of appendices with title and identification

Energy Technology Data Exchange (ETDEWEB)

None

1982-01-01

This final technical report describes what WyCoalGas, Inc. and its subcontractors accomplished in resolving issues related to the resource, technology, economic, environmental, socioeconomic, and governmental requirements affecting a project located near Douglas, Wyoming for producing 150 Billion Btu per day by gasifying sub-bituminous coal. The report summarizes the results of the work on each task and includes the deliverables that WyCoalGas, Inc. and the subcontractors prepared. The co-venturers withdrew from the project for two reasons: federal financial assistance to the project was seen to be highly uncertain; and funds were being expended at an unacceptably high rate.

Neutron and gamma-ray transmission technique for the on-line determination of moisture in coal and coke

International Nuclear Information System (INIS)

Sowerby, B.D.; Millen, M.J.; Rafter, P.T.

1985-01-01

A fast neutron and gamma-ray transmission technique is being developed for the on-line analysis of moisture in coal and coke. The technique utilises 252 Cf and 137 Cs sources and 3 He and NaI(Tl) detectors. Laboratory measurements on single coal samples have shown that moisture can be determined to better than 1 wt% over the range 0 to 16 wt% moisture and 5 to 17cm thickness. Reduced errors were obtained for restricted ranges of moisture and thickness. Preliminary measurements on coke of thickness 30 to 50cm have shown that moisture can be determined to within 0.26 wt% over the range 1 to 16 wt% moisture

Enhanced Combustion Low NOx Pulverized Coal Burner

Energy Technology Data Exchange (ETDEWEB)

David Towle; Richard Donais; Todd Hellewell; Robert Lewis; Robert Schrecengost

2007-06-30

For more than two decades, Alstom Power Inc. (Alstom) has developed a range of low cost, infurnace technologies for NOx emissions control for the domestic U.S. pulverized coal fired boiler market. This includes Alstom's internally developed TFS 2000{trademark} firing system, and various enhancements to it developed in concert with the U.S. Department of Energy. As of the date of this report, more than 270 units representing approximately 80,000 MWe of domestic coal fired capacity have been retrofit with Alstom low NOx technology. Best of class emissions range from 0.18 lb/MMBtu for bituminous coal to 0.10 lb/MMBtu for subbituminous coal, with typical levels at 0.24 lb/MMBtu and 0.13 lb/MMBtu, respectively. Despite these gains, NOx emissions limits in the U.S. continue to ratchet down for new and existing boiler equipment. On March 10, 2005, the Environmental Protection Agency (EPA) announced the Clean Air Interstate Rule (CAIR). CAIR requires 25 Eastern states to reduce NOx emissions from the power generation sector by 1.7 million tons in 2009 and 2.0 million tons by 2015. Low cost solutions to meet such regulations, and in particular those that can avoid the need for a costly selective catalytic reduction system (SCR), provide a strong incentive to continue to improve low NOx firing system technology to meet current and anticipated NOx control regulations. The overall objective of the work is to develop an enhanced combustion, low NOx pulverized coal burner, which, when integrated with Alstom's state-of-the-art, globally air staged low NOx firing systems will provide a means to achieve: Less than 0.15 lb/MMBtu NOx emissions when firing a high volatile Eastern or Western bituminous coal, Less than 0.10 lb/MMBtu NOx emissions when firing a subbituminous coal, NOx reduction costs at least 25% lower than the costs of an SCR, Validation of the NOx control technology developed through large (15 MWt) pilot scale demonstration, and Documentation required for

Process and analytical studies of enhanced low severity co-processing using selective coal pretreatment. Final technical report

Energy Technology Data Exchange (ETDEWEB)

Baldwin, R.M.; Miller, R.L.

1991-12-01

The findings in the first phase were as follows: 1. Both reductive (non-selective) alkylation and selective oxygen alkylation brought about an increase in liquefaction reactivity for both coals. 2. Selective oxygen alkylation is more effective in enhancing the reactivity of low rank coals. In the second phase of studies, the major findings were as follows: 1. Liquefaction reactivity increases with increasing level of alkylation for both hydroliquefaction and co-processing reaction conditions. 2. the increase in reactivity found for O-alkylated Wyodak subbituminous coal is caused by chemical changes at phenolic and carboxylic functional sites. 3. O-methylation of Wyodak subbituminous coal reduced the apparent activation energy for liquefaction of this coal.

Extractive de-sulfurization and de-ashing of high sulfur coals by oxidation with ionic liquids

International Nuclear Information System (INIS)

Saikia, Binoy K.; Khound, Kakoli; Baruah, Bimala P.

2014-01-01

Highlights: • Extractive de-sulfurization and de-ashing process for cleaning high sulfur coals. • The process removes inorganic as well as organic sulfur components from high sulfur coals. • The process has less risk to chemists and other surroundings. - Abstract: The environmental consequences of energy production from coals are well known, and are driving the development of desulfurization technologies. In this investigation, ionic liquids were examined for extractive desulfurization and de-ashing in industrially important high sulfur sub-bituminous Indian coals. The ionic liquids, namely, 1-n-butyl-3-methylimidazolium tetrafluoroborate (IL1) and 1-n-butyl 3-methylimidazolium chloride (IL2) were employed for desulfurization of a few Indian coal samples in presence of HCOOH/H 2 O 2 and V 2 O 5 . Results show the maximum removal of 50.20% of the total sulfur, 48.00% of the organic sulfur, and 70.37 wt% of the ash in this process. The ionic liquids were recovered and subsequently used for further desulfurization. FT-IR spectra reveal the transformation of organic sulfur functionalities into the sulfoxides (S=O) and sulfones (-SO 2 ) due to the oxidative reactions. The sulfate, pyrite and sulfides (aryls) signals in the near edge X-ray absorption fine structure (NEXAFS) of the oxidized coal samples showed sulfur transformation during the desulfurization process. The study demonstrates the removal of significant amount of inorganic as well as organic sulfur (aryls) components from the original high sulfur coal samples to make them cleaner

An update on blast furnace granular coal injection

Energy Technology Data Exchange (ETDEWEB)

Hill, D.G. [Bethlehem Steel Corp., Burns Harbor, IN (United States); Strayer, T.J.; Bouman, R.W. [Bethlehem Steel Corp., PA (United States)

1997-12-31

A blast furnace coal injection system has been constructed and is being used on the furnace at the Burns Harbor Division of Bethlehem Steel. The injection system was designed to deliver both granular (coarse) and pulverized (fine) coal. Construction was completed on schedule in early 1995. Coal injection rates on the two Burns Harbor furnaces were increased throughout 1995 and was over 200 lbs/ton on C furnace in September. The injection rate on C furnace reached 270 lbs/ton by mid-1996. A comparison of high volatile and low volatile coals as injectants shows that low volatile coal replaces more coke and results in a better blast furnace operation. The replacement ratio with low volatile coal is 0.96 lbs coke per pound of coal. A major conclusion of the work to date is that granular coal injection performs very well in large blast furnaces. Future testing will include a processed sub-bituminous coal, a high ash coal and a direct comparison of granular versus pulverized coal injection.

Characterization of Malaysian coals for carbon dioxide sequestration

Science.gov (United States)

Abunowara, M.; Bustam, M. A.; Sufian, S.; Eldemerdash, U.

2016-06-01

Coal samples from Mukah-Balingian and Merit-Pila coal mines were characterized with ultimate, approximate, petrographic analysis, FT-IR spectra patterns, FESEM images and BET measurements to obtain information on the chemical composition and chemical structure in the samples. Two coal samples were obtained from Merit-Pila coal mine namely sample1 (S1) and sample2 (S2). The other two coal samples were obtained from Mukah-Balingian coal mine namely sample3 (S3) and sample4 (S4), Sarawak, Malaysia. The results of ultimate analysis show that coal S1 has the highest carbon percentage by 54.47%, the highest hydrogen percentage by 10.56% and the lowest sulfur percentage by 0.19% and the coal S4 has the highest moisture content by 31.5%. The coal S1 has the highest fixed carbon percentage by 42.6%. The coal S4 has BET surface area by 2.39 m2/g and Langmuir surface area by 3.0684 m2/g respectively. Fourier-Transform Infrared (FT-IR) spectroscopy analysis of all coal samples shows a presence of oxygen containing functional groups which considered are as active sites on coal surface. The oxygen functional groups are mainly carboxyl (-COOH), hydroxyl (-OH), alkyl (-CH, -CH2, -CH3), aliphatic (C-O-C stretching associated with -OH), amino (-NH stretching vibrations), (-NH stretching vibrations), aromatic (C=C), vinylic (C=C) and clay minerals. In all FE-SEM images of coal samples matrix, it can be seen that there are luminous and as non luminous features which refer to the existence of various minerals types distributed in the coal organic matrix. The bright luminosity is due to the presence of sodium, potassium or aluminium. According to petrographic analysis, all coal sample samples are range in vitrinite reflectance from 0.38% to 56% (VRr) are sub-bituminous coals.

Assessment of low-rank (LRC) drying technologies

International Nuclear Information System (INIS)

Willson, W.G.; Young, B.C.; Irwinj, W.

1992-01-01

This paper reports that low-rank coals (LRCs), brown, lignitic, and subbituminous coals, represent nearly half of the estimated coal resources in the world. In many of the developing nations, LRCs are the only source of low-cost energy. LRCs are geologically younger than higher-rank bituminous coals and are typically present in thick seams with less cover (overburden) than bituminous coals, making them recoverable by low-cost strip mining. Current pit-head coal prices for LRCs range from a low of around $0.25 per MM Btus for subbituminous coals from the USA's Powder River Basin, to highs of around $1,00 for those that are more costly to mine. On the other hand, the pit-head price of bituminous coals in the USA range from a low of around $1 to over $2 per MM Btu. Unfortunately, this differential in favor of LRC is more than offset in distant markers where, until now, it has been considered a nuisance. Often less than half of its weight is combustible, the rest being water and ash. Thus the cost of hauling it any distance at all in its untreated dry bulk form is prohibitive. However, from a utilization aspect, LRCs have a lower fuel ration (fixed carbon to volatile matter) and are typically an order of magnitude more reactive than bituminous coals. Many LRCs, including the enormous reserves in Alaska, Australia, and Indonesia, also have extremely low sulfur contents of only a few tenths of a percent. Low mining costs, high reactivity, and extremely low sulfur content would make these coals premium fuel were it not for their high moisture levels, which range from around 25% w/w to over 60% w/w. High moisture creates a mistaken perception, among major coal importers, of inferior quality, and the many positive features of LRCs are overlooked

An under-belt capacitance and γ-ray backscatter gauge for on-line determination of moisture in coal

International Nuclear Information System (INIS)

Cutmore, N.G.; Roczniok, A.F.; Sowerby, B.D.

1987-01-01

A non-contacting under-belt capacitance and γ-ray backscatter technique has been developed for on-line measurement of moisture in coal. In this technique, moisture was correlated with radiofrequency susceptance and conductance, determined using an under-belt capacitance sensor in which a fringing electric field interrogates a layer of coal on the conveyor belt directly above the sensor. To compensate for variation in the density and thickness of the coal layer, an under-belt γ-ray backscatter gauge was used to measure an equivalent volume of coal. Laboratory measurements have shown that this technique compensates more accurately for density and thickness than does their direct physical measurement. (author)

Characterization of Activated Carbon from Coal and Its Application as Adsorbent on Mine Acid Water Treatment

Directory of Open Access Journals (Sweden)

Siti Hardianti

2017-06-01

Full Text Available Anthracite and Sub-bituminous as activated carbon raw material had been utilized especially in mining field as adsorbent of dangerous heavy metal compound resulted in mining activity. Carbon from coal was activated physically and chemically in various temperature and particle sizes. Characterization was carried out in order to determine the adsorbent specification produced hence can be used and applied accordingly. Proximate and ultimate analysis concluded anthracite has fixed carbon 88.91% while sub-bituminous 49.05%. NaOH was used in chemical activation while heated at 400-500°C whereas physical activation was conducted at 800-1000°C. Activated carbon has high activity in adsorbing indicated by high iodine number resulted from analysis. SEM-EDS result confirmed that activated carbon made from coal has the quality in accordance to SNI and can be used as adsorbent in acid water treatment.

57Fe NGR studies on three-stage hydroliquefaction of coals

International Nuclear Information System (INIS)

Jamond, M.; Bacaud, R.; Bussiere, P.; Charcosset, H.; Nickel-Pepin-Donat, B.

1990-01-01

Iron Moessbauer spectroscopy has been performed on liquefaction residues of two different French coals. In a three-stage liquefaction of high volatile bituminous coal (Freyming), without an added catalyst, the coal pyrite is not entirely converted into pyrrhotites, whereas in the presence of an added catalyst, coal pyrite is totally transformed into more dispersed pyrrhotites than those from the sample without an added catalyst; furthermore, the whole added catalyst precursor is reduced into pyrrhotites. In the case of liquefaction of subbituminous coal (Gardanne), full conversion of coal pyrite into pyrrhotites (even without an added catalyst) occurs. In addition, in the presence of the added catalyst, besides pyrrhotites, FeS is evidenced. When molybdenum-iron oxide is added as a catalyst precursor, no mixed Fe-Mo phase is detected. (orig.)

Export market potential for Alaskan and Western US coals

International Nuclear Information System (INIS)

Sims, J.

1992-01-01

Major utilization trends may create opportunity for dramatic expansion of Alaska's coal exports from a huge ultra-low sulfur coal resource base. Markets are expected to open up in the Pacific Basin for sub-bituminous and bituminous steam coals from Alaska to include not only run-of-mine coals but also product streams from beneficiation technologies. Market considerations aside, deficiencies in physical infrastructure and an unresolved resource ownership issue are the principal impediments at this time to property development

Generating a representative signal of coal moisture content to anticipate combustion control in thermal power stations

Energy Technology Data Exchange (ETDEWEB)

Prieto-Fernandez, Ismael; Luengo-Garcia, J. Carlos; Alonso-Hidalgo, Manuela; Ponte-Gutierrez, Daniel [Area de Maquinas y Motores Termicos, Universidad de Oviedo, Campus Universitario s/n 33203, Asturias Gijon (Spain)

2002-06-01

This article describes the possibilities of continuously measuring coal moisture in the boiler feeding circuit of a thermal power station so that the measurement can be used as a signal for the boiler combustion control system. To do so, in the first place, the point through which coal would be fed into the boiler was chosen. After studying the different parts of the circuit, the feeder was selected. Then, an installation was designed, at semi-industrial scale, faithfully reproducing the operation of a belt conveyor. In order to measure the moisture content, a microwave system was installed, and a large number of coal samples with different ranks and grain sizes was tested showing eventually the likelihood of the objective.

Kinetic Study of Coal and Biomass Co-Pyrolysis Using Thermogravimetry

Energy Technology Data Exchange (ETDEWEB)

Wang, Ping [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Hedges, Sheila W. [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Chaudharib, Kiran [West Virginia Univ., Morgantown, WV (United States). Department of Chemical Engineering; Turtonb, Richard [West Virginia Univ., Morgantown, WV (United States). Department of Chemical Engineering

2013-10-29

The objectives of this study are to investigate thermal behavior of coal and biomass blends in inert gas environment at low heating rates and to develop a simplified kinetic model using model fitting techniques based on TGA experimental data. Differences in thermal behavior and reactivity in co-pyrolysis of Powder River Basin (PRB) sub-bituminous coal and pelletized southern yellow pine wood sawdust blends at low heating rates are observed. Coal/wood blends have higher reactivity compared to coal alone in the lower temperature due to the high volatile matter content of wood. As heating rates increase, weight loss rates increase. The experiment data obtained from TGA has a better fit with proposed two step first order reactions model compared single first order reaction model.

Environmental Policy Induced Input Substitution? The Case of Coking and Steam Coal

OpenAIRE

Ian Lange

2007-01-01

The Clean Air Act of 1990 initiated a tradable permit program for emissions of sulfur dioxide from coal-fired power plants. The effect of this enlightened policy on the coal industry was a large increase in consumption of low-sulfur bituminous and subbituminous coals. Low-sulfur bituminous coal is most attractive to coal-fired power plants as they have higher heat content and require less alteration to the boiler to burn as effectively the coal previously in use. However, low-sulfur bituminou...

Relations between flash pyrolysis reactivity and oil/gas products from coals of different rank; Sekitankado no kotonaru shushu no sekitan no flash pyrolysis hannosei to gas oyobi eki seiseibutsu no kankei

Energy Technology Data Exchange (ETDEWEB)

Nonaka, T.; Kishino, M.; Sakanishi, K.; Korai, Y.; Mochida, I. [Kyushu University, Fukuoka (Japan). Institute of Advanced Material Study

1996-10-28

Curie point flash pyrolysis (FP) reactivity was studied experimentally using three kinds of coals with different coal ranks such as Yallourn brown coal, Tanitoharum sub-bituminous coal and Wandoan sub-bituminous coal. Experiment was performed using a curie point pyrolyzer in carrier gas of 20ml/min in gas flow rate at 450, 590 and 740{degree}C for 5sec. The experimental results were as follows. Each gas component obviously increased at 450-590{degree}C, however, C4-C6 gases drastically decreased at 590-740{degree}C accompanying reduction of the whole gas quantity. All of each polar component remarkably increased at 450-590{degree}C. Yallourn brown coal with high Owt%, in particular, contained a large amount of alkyl-hydroxybenzene group. The amount of cresol of all of three coal specimens also increased at 740{degree}C. It was thus suggested that this is coal constituent molecules derived from cutting of methylene-ether bridged bond by higher-temperature FP. 8 refs., 5 figs., 3 tabs.

Investigation on characterization of Ereen coal deposit

Directory of Open Access Journals (Sweden)

S. Jargalmaa

2016-03-01

Full Text Available The Ereen coal deposit is located 360 km west from Ulaanbaatar and 95 km from Bulgan town. The coal reserve of this deposit is approximately 345.2 million tons. The Ereen coal is used directly for the Erdenet power plant for producing of electricity and heat. The utilization of this coal for gas and liquid product using gasification and pyrolysis is now being considered. The proximate and ultimate analysis show that the Ereen coal is low rank D mark hard coal, which corresponds to subbituminous coal. The SEM images of initial coal sample have compact solid pieces. The SEM image of carbonized and activated carbon samples are hard material with high developed macro porosity structure. The SEM images of hard residue after thermal dissolution in autoclave characterizes hard pieces with micro porous structure in comparison with activated carbon sample. The results of the thermal dissolution of Ereen coal in tetralin with constant weight ratio between coal and tetralin (1:1.8 at the 450ºC show that 38% of liquid product can be obtained by thermal decomposition of the COM (coal organic matter.Mongolian Journal of Chemistry 16 (42, 2015, 18-21

Technical report on NEDO-conducted Western US steam coal (for power generation and boiler) survey

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

The New Energy and Industrial Technology Development Organization (NEDO) conducted studies covering Wyoming, Utah, Colorado, New Mexico, and North Dakota, all in the West. Illinois and Gulf-Texas are also included. The bituminous coal of Utah and Colorado is given the highest priority as coal to be exported to Japan. It is feared, however, that the price of the bituminous coal from these areas may soar if demand increases. As for sub-bituminous coal, its price is far more stable because its reserves are basically limitless. The sub-bituminous coal, however, is not expected to be imported to Japan in the very near future because it is low in calorific power and fails to meet the conditions prerequisite to Japan's boiler fuel. Illinois can receive large orders but its coal contains more sulfur than the Western coal and a longer distance has to be covered for its transportation. As for transportation to the West Cost, freight cars are available and the port capacity can be enlarged dependent on the magnitude of demand for coal. Loading a deep draft bulk ship off shore with coarse coal slurry by pipeline is an attractive scheme. (NEDO)

Technical report on NEDO-conducted Western US steam coal (for power generation and boiler) survey

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

The New Energy and Industrial Technology Development Organization (NEDO) conducted studies covering Wyoming, Utah, Colorado, New Mexico, and North Dakota, all in the West. Illinois and Gulf-Texas are also included. The bituminous coal of Utah and Colorado is given the highest priority as coal to be exported to Japan. It is feared, however, that the price of the bituminous coal from these areas may soar if demand increases. As for sub-bituminous coal, its price is far more stable because its reserves are basically limitless. The sub-bituminous coal, however, is not expected to be imported to Japan in the very near future because it is low in calorific power and fails to meet the conditions prerequisite to Japan's boiler fuel. Illinois can receive large orders but its coal contains more sulfur than the Western coal and a longer distance has to be covered for its transportation. As for transportation to the West Cost, freight cars are available and the port capacity can be enlarged dependent on the magnitude of demand for coal. Loading a deep draft bulk ship off shore with coarse coal slurry by pipeline is an attractive scheme. (NEDO)

Nuclear techniques for analysis of coal for calorific value, ash and moisture

International Nuclear Information System (INIS)

Dains, Margaret

1976-03-01

This bibliography includes references on nuclear techniques for analysis of coal for calorific value, ash and moisture content. As the search was directed particularly towards measurement of the ash content of coal using x- and gamma-ray methods, references covering only β-ray techniques have been placed in a separate section. References from Chemical Abstracts prior vol.62 (1965) do not cite the language of the original article. The language of the original has been given for all other articles not in English. (author)

A study on the measurement of coal moisture by the neutron method

International Nuclear Information System (INIS)

Ma Yonghe

1985-01-01

The paper reports the result of measuring coal moisture by the neutron method. A deducting intercept method is used to eliminate the effects of the structural hydrogen and the matrix effect. A measuring device has been developed and its measuring accuracy is less than 1%

Investigation on characterization and liquefaction of coals from Tavan tolgoi deposit

Directory of Open Access Journals (Sweden)

B Purevsuren

2014-10-01

Full Text Available On the basis of proximate, ultimate, petrographic and IR analysis results have been confirmed that the Tavan tolgoi coal is a high-rank G mark stone coal. The results of X-ray fluorescence analysis of coal ash show that the Tavan tolgoi coal is a subbituminous coal. The ash of Tavan tolgoi coal has an acidic character. The results of pyrolysis of Tavan tolgoi coal at different heating temperatures show that a maximum yield - 5.0% of liquid product can be obtained at 700°C. The results of thermal dissolution of Tavan tolgoi coal in tetralin with constant mass ratio between coal and tetralin (1:1.8 at 450°C show that 50.0% of liquid product can be obtained after thermal decomposition of the COM (coal organic matter. DOI: http://dx.doi.org/10.5564/mjc.v14i0.191 Mongolian Journal of Chemistry 14 (40, 2013, p12-19

Arsenic concentrations in Chinese coals

International Nuclear Information System (INIS)

Wang Mingshi; Zheng Baoshan; Wang Binbin; Li Shehong; Wu Daishe; Hu Jun

2006-01-01

The arsenic concentrations in 297 coal samples were collected from the main coal-mines of 26 provinces in China were determined by molybdenum blue coloration method. These samples were collected from coals that vary widely in coal rank and coal-forming periods from the five main coal-bearing regions in China. Arsenic content in Chinese coals range between 0.24 to 71 mg/kg. The mean of the concentration of Arsenic is 6.4 ± 0.5 mg/kg and the geometric mean is 4.0 ± 8.5 mg/kg. The level of arsenic in China is higher in northeastern and southern provinces, but lower in northwestern provinces. The relationship between arsenic content and coal-forming period, coal rank is studied. It was observed that the arsenic contents decreases with coal rank in the order: Tertiary > Early Jurassic > Late Triassic > Late Jurassic > Middle Jurassic > Late Permian > Early Carboniferous > Middle Carboniferous > Late Carboniferous > Early Permian; It was also noted that the arsenic contents decrease in the order: Subbituminous > Anthracite > Bituminous. However, compared with the geological characteristics of coal forming region, coal rank and coal-forming period have little effect on the concentration of arsenic in Chinese coal. The average arsenic concentration of Chinese coal is lower than that of the whole world. The health problems in China derived from in coal (arsenism) are due largely to poor local life-style practices in cooking and home heating with coal rather than to high arsenic contents in the coal

Plant trial of an under-belt capacitance and gamma-ray backscatter gauge for on-belt determination of moisture in coal

International Nuclear Information System (INIS)

Cutmore, N.G.; Rafter, P.T.; Abernethy, D.A.; Millen, M.J.

1989-01-01

A non-contacting under-belt capacitance and gamma-ray backscatter technique has been developed for the on-line measurement of moisture in coal. In this technique, moisture was correlated with radio frequency susceptance and conductance, determined using an under-belt capacitance sensor in which a fringing electric field interrogates a layer of coal on the conveyor belt directly about the sensor. To compensate for variations in the density and thickness of the coal layer, an under-belt gamma-ray backscatter gauge was used to measure an equivalent volume of coal. A plant trial of the technique was conducted at Stockton Borehole Colliery, NSW Australia, where the gauges were installed on the coking coal product conveyor. Product moistures, in the range 7-14%, were determined with r.m.s errors of 0.50 and 0.25 wt% using on-belt and static off-belt gauges, respectively. The difference in the on-belt and off-belt gauge measurement accuracy was attributed to sampling errors in the calibration of the on-belt gauge. 6 refs., 6 figs., 3 tabs

Apparatus and process for continuous measurement of moisture in moving coal by neutron thermalization

International Nuclear Information System (INIS)

Stewart, R.F.

1967-01-01

The invention relates to an apparatus and process for the measurement of moisture contents in solid materials. More particularly, the invention makes available a continuous moisture analysis of a moving mass of material, such as coal, by penetrating such material with neutrons emitted from a source of fast neutrons and detecting, counting, and recording slowed or thermalized neutrons reflected from the internal structure of the material. (U.S.)

Clean coal technology

International Nuclear Information System (INIS)

Abelson, P.H.

1990-01-01

One of the major technology challenges in the next decade will be to develop means of using coal imaginatively as a source of chemicals and in a more energy-efficient manner. The Clean Air Act will help to diminish the acid rain but will not reduce CO 2 emissions. The Department of Energy (DOE) is fostering many innovations that are likely to have a positive effect on coal usage. Of the different innovations in the use of coal fostered by DOE, two are of particular interest. One is the new pressurized fluid bed combustion (PFBC) combined-cycle demonstration. The PFBC plant now becoming operational can reduce SO 2 emissions by more than 90% and NO x emissions by 50-70%. A second new technology co-sponsored by DOE is the Encoal mild coal gasification project that will convert a sub-bituminous low-BTU coal into a useful higher BTU solid while producing significant amounts of a liquid fuel

Current status of U.S. coal utilization and non-fuel uses of fossil fuels

International Nuclear Information System (INIS)

Song, C.S.; Schobert, H.; Scaroni, A.W.

1997-01-01

An understanding of the current situation is important for projecting the future direction of coal utilization. The world's annual consumption of coal in 1995 was 5104.01 million short tons (MST, 1 short ton = 0.907 metric ton). Coal plays a very important role in the US energy supply; US coal production in 1995 totaled 1033 MST, including 611.1 MST of bituminous coal, 328.4 MST of subbituminous coal, 86.1 MST of lignite, and 4.1 MST of anthracite. US coal consumption totaled 940.6 MST, with 88.1% in electric utilities, 3.5% in coke plants, 7.8% for other industrial uses, and only 0.6% in the residential and commercial sectors. The amount of fossil resources used for non-fuel purposes accounted for 8.4% of the total annual consumption in 1995. Non-fuel uses of fossil fuels particularly coal may become more important in the future. The demonstrated coal reserves in the world are large enough for consumption for over 220 years at the 1995 level, while proven oil reserves are only about 40 times the world's 1995 consumption level. Coal has several positive attributes when considered as a feedstock for aromatic chemicals, specialty chemicals, and carbon-based materials. Existing nonfuel uses of coals include (1) high temperature carbonization of bituminous and subbituminous coals to make metallurgical coke; (2) gasification of coal to make synthesis gases and other chemicals; (3) use of coal in manufacturing other materials such as activated carbons, carbon molecular sieves (CMS) and production of phosphorus (phosphoric acid); (4) the use of coal tars from carbonization and gasification for making aromatic and phenolic chemicals; (5) the use of coal tar pitch for making carbon fibers and activated carbon fibers; and (6) other non-fuel products derived from coal including combustion by-products. Coal may become more important both as an energy source and as the source of chemical feedstocks in the 21st century

Thermogravimetric determination of the carbon dioxide reactivity of char from some New Zealand coals and its association with the inorganic geochemistry of the parent coal

Energy Technology Data Exchange (ETDEWEB)

Beamish, B.B.; Shaw, K.J.; Rodgers, K.A.; Newman, J. [University of Auckland, Auckland (New Zealand). Dept. of Geology

1998-02-01

Thermogravimetrically-determined carbon dioxide reactivities of char formed from New Zealand coals, ranging in rank from lignite to high volatile bituminous, vary from 0.12 to 10.63 mg/h/mg on a dry, ash-free basis. The lowest rank subbituminous coal chars have similar reactivities to the lignite coal chars. Calcium content of the char shows the strongest correlation with reactivity, which increases as the calcium content increases. High calcium per se does not directly imply a high char reactivity. Organically-bound calcium catalyses the conversion of carbon to carbon monoxide in the presence of carbon dioxide, whereas calcium present as discrete minerals in the coal matrix e.g., calcite, fails to significantly affect reactivity. Catalytic effects of magnesium, iron, sodium and phosphorous are not as obvious, but can be recognised for individual chars. The thermogravimetric technique provides a fast, reliable analysis that is able to distinguish char reactivity differences between coals, which may be due to any of the above effects. 27 refs., 6 figs., 4 tabs.

Emissions characterization from a variety of coals on a pilot-scale facility_v1

Data.gov (United States)

U.S. Environmental Protection Agency — The current study not only characterizes emissions from three coals (bituminous, sub-bituminous, and lignite), but also investigates the use of instrumentation for...

Electrochemistry of carbonaceous materials. 3. Reactivity of redox couples with coal slurries in 85% phosphoric acid media

Energy Technology Data Exchange (ETDEWEB)

Tomat, R.; Salmaso, R.; Zecchin, S. [CNR - Istituto di Polarografia ed Elettrochimica Preparativa, Padova (Italy)

1994-02-01

Sardinian subbituminous coal slurries were oxidized in 85% H{sub 3}PO{sub 4} by metal ions (Ce{sup 4+}, V{sup 5+}, V{sup 4+}, Mn{sup 3+} and Fe{sup 3+}) and the effects of metal ion concentration, coal content of slurry, coal particle size and temperature were examined. 19 refs., 3 figs., 2 tabs.

Effect of resinite on the combustion of New Zealand subbituminous coal

Energy Technology Data Exchange (ETDEWEB)

Benfell, K.E.; Beamish, B.B.; Rodgers, K.A. [University of Newcastle, Callaghan, NSW (Australia). Dept. of Geology

1997-09-01

This paper shows that Oligocene resin from New Zealand`s Rotowaro coalfield displays DTA and DTG traces similar to those of other fossil resins. It modifies the thermal behaviour of low rank coal raising the peak combustion temperature and lowering its rate of combustion; this behaviour may be common among liptinite macerals. The effect is not additive and unlike other coal constituents the resinite component does not deteriorate with time.

Development of clean coal and clean soil technologies using advanced agglomeration techniques

International Nuclear Information System (INIS)

Ignasiak, B.; Ignasiak, T.; Szymocha, K.

1990-01-01

Three major topics are discussed in this report: (1) Upgrading of Low Rank Coals by the Agflotherm Process. Test data, procedures, equipment, etc., are described for co-upgrading of subbituminous coals and heavy oil; (2) Upgrading of Bituminous Coals by the Agflotherm Process. Experimental procedures and data, bench and pilot scale equipments, etc., for beneficiating bituminous coals are described; (3) Soil Clean-up and Hydrocarbon Waste Treatment Process. Batch and pilot plant tests are described for soil contaminated by tar refuse from manufactured gas plant sites. (VC)

Nuclear assay of coal. Volume 1. Coal composition by prompt neutron activation analysis: basic experiments. Final report

International Nuclear Information System (INIS)

Reynolds, G.; Bozorganesh, H.; Elias, E.; Gozani, T.; Maung, T.; Orphan, V.

1979-01-01

Using californium-252 as a source of exciting neutrons, prompt gamma photons emitted by elemental nuclei in the coal have been measured using several detectors, including sodium--iodide and germanium--lithium. Several coal types, including bituminous, subbituminous lignite and anthracite were crushed to various top sizes and analyzed carefully be traditional ASTM wet chemistry techniques at two or three different laboratories. The elements (sulfur, hydrogen, carbon, aluminum, silicon, iron, calcium, sodium, nitrogen, and chlorine) were determined by prompt neutron activations and the quantities compared with those of the wet chemical analyses

Aspects of combustion behaviour of coals from some New Zealand lignite-coal regions determined by thermogravimetry

Energy Technology Data Exchange (ETDEWEB)

Benfell, K.E.; Beamish, B.B.; Rodgers, K.A. [University of Newcastle, Callaghan, NSW (Australia). Dept. of Geology

1997-08-25

The papers describes how thermogravimetric analysis of five Late Cretaceous and Cenozoic New Zealand lignites demonstrate that their combustion behaviour is distinct from that of subbituminous coals and may be characterised by peak temperature of 377-416{degree}C, maximum rate of combustion of 25-31 wt% min{sup -1}, and temperature of char burnout 421-497{degree}C. These parameters reflect variation in thermal behaviour associated with both the organic and inorganic constituents of the coal. The information obtained is additional to that provided by proximate analysis; the latter is insufficient to predict the combustion behaviour of the coals relative to one another. A post-combustion thermal event is seen among the lignites as in other low-rank coals combusting below 600{degree}C, which appears to be related to the organic sulphur content of the coal.

Thermogravimetric analytical procedures for determining reactivities of chars from New Zealand coals

Energy Technology Data Exchange (ETDEWEB)

Shaw, K.J.; Beamish, B.B.; Rodgers, K.A. [University of Auckland, Auckland (New Zealand). Dept. of Geology

1997-10-22

This paper describes how tightly constrained thermogravimetric experimental procedures (particle size {lt} 212 {mu}m, sample mass 15.5 mg, CO{sub 2} reactant gas, near isothermal conditions) allow the reactivity of chars from high volatile New Zealand coals to be determined to a repeatability of {+-}0.07 h{sup -1} at 900{degree}C and {+-}0.5 h{sup -1} at 1100{degree}C. The procedure also provides proximate analyses information and affords a quick ({lt} 90 min) comparison between different coal types as well as indicating likely operating conditions and problems associated with a particular coal or blend. A clear difference is evident between reactivities of differing New Zealand coal ranks. Between 900 and 1100{degree}C, bituminous coals increase thirtyfold in reactivity compared with fourfold for subbituminous, with the latter being three to five times greater in reactivity at higher temperature.

Lawrence Livermore National Laboratory underground coal gasification data base. [US DOE-supported field tests; data

Energy Technology Data Exchange (ETDEWEB)

Cena, R. J.; Thorsness, C. B.

1981-08-21

The Department of Energy has sponsored a number of field projects to determine the feasibility of converting the nation's vast coal reserves into a clean efficient energy source via underground coal gasification (UCG). Due to these tests, a significant data base of process information has developed covering a range of coal seams (flat subbituminous, deep flat bituminous and steeply dipping subbituminous) and processing techniques. A summary of all DOE-sponsored tests to data is shown. The development of UCG on a commercial scale requires involvement from both the public and private sectors. However, without detailed process information, accurate assessments of the commercial viability of UCG cannot be determined. To help overcome this problem the DOE has directed the Lawrence Livermore National Laboratory (LLNL) to develop a UCG data base containing raw and reduced process data from all DOE-sponsored field tests. It is our intent to make the data base available upon request to interested parties, to help them assess the true potential of UCG.

Pilot plant assessment of blend properties and their impact on critical power plant components

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-10-01

A series of tests were performed to determine the effects of blending eastern bituminous coals with western subbituminous coals on utility boiler operation. Relative to the baseline bituminous coal, the testing reported here indicated that there were significant impacts to boiler performance due to the blending of the eastern and western coals. Results indicated that fuel blending can be used to adequately control flue gas emissions of both SO{sub 2} and NO{sub x} at the expense of reduced milling efficiency, increased sootblowing in the high-temperature and low-temperature regions of the boiler and, to a lesser extent, decreased collection efficiency for an electrostatic precipitator. The higher reactivity of the subbituminous coal increased the overall combustion efficiency, which may tend to decrease the impact of milling efficiency losses. The extent of these impacts was directly related to the percentage of subbituminous coal in the blends. At the lowest blend ratios of subbituminous coal, the impacts were greatly reduced.

Trends and outlook of coal energy in Malaysia

Energy Technology Data Exchange (ETDEWEB)

Zainal Abidin Husin (Tenaga Nasional Berhad, Kuala Lumpur (Malaysia). Fuel and Materials Management Dept.)

1993-03-01

Current energy policy in Malaysia is directed towards development of natural gas resources although there is a strategy to diversify energy sources to gas, hydro, coal and oil. By the year 2000, however, coal could emerge as a major energy source. The author advocates the need for a policy direction for the coal industry - for exploration, mine planning, mixing methods, transport and regulations to ensure occupational health and safety. Malaysia has abundant coal resources but most are in Sarawak and Sabah whereas the bulk of energy demand is in the Peninsula Malaysia. A table defines known coal resources in Malaysia and a map shows their location. To ensure successful development of the coal industry, technologies must be developed to meet environmental requirements and global market competition. Several emerging technologies are mentioned: production of process-derived fuel and coal-derived liquid from sub-bituminous coal, coal liquefaction, manufacture of coal water mixture, coal beneficiation, and fluidised bed combustion. 1 fig., 1 tab.

Low NO{sub x} burner modifications to front-fired pulverized coal boilers

Energy Technology Data Exchange (ETDEWEB)

Broderick, R G; Wagner, M

1998-07-01

Madison Gas and Electric Blount Street Station Units 8 and 9 are Babcock and Wilcox pulverized coal fired and natural gas fired boilers. These boilers were build in the late 1950's and early 1960's with each boiler rated at 425,000 lb./hr of steam producing 50 MW of electricity. The boilers are rated at 9,500 F at 1,350 psig. Each unit is equipped with one Ljungstroem air heater and two B and W EL pulverizers. These units burn subbituminous coal with higher heating value of 10,950 Btu/LB on an as-received basis. The nitrogen content is approximately 1.23% with 15% moisture. In order to comply with the new Clean Air Act Madison Gas and Electric needs to reduce NO{sub x} on these units to less than .5 LB/mmBtu. Baseline NO{sub x} emissions on these units range between .8--.9 lb./mmBtu. LOIs average approximately 8%. Madison Gas and Electric contracted with RJM Corporation to modify the existing burners to achieve this objective. These modifications consisted of adding patented circumferentially and radially staged flame stabilizers, modifying the coal pipe, and replacing the coal impeller with a circumferentially staged coal spreader. RJM Corporation utilized computational fluid dynamics modeling in order to design the equipment to modify these burners. The equipment was installed during the March 1997 outage and start-up and optimization was conducted in April 1997. Final performance results and economic data will be included in the final paper.

Nuclear assay of coal. Volume 8. Continuous nuclear assay of coal (CONAC). Final report

International Nuclear Information System (INIS)

Lagarias, J.; Irminger, P.; Dodson, W.

1979-01-01

Using californium-252 as a source of exciting neutrons, prompt gamma photons emitted by elemental nuclei in the coal have been measured using several detectors, including sodium-iodide and germanium-lithium. Several coal types, including bituminous, subbituminous lignite and anthracite were crushed to various top sizes and analyzed carefully by traditional ASTM wet chemistry techniques at two or three different laboratories. The elements (sulfur, hydrogen, carbon, aluminum, silicon, iron, calcium, sodium, nitrogen, and chlorine) were determined by prompt neutron activations and the quantities compared with those of the wet chemical analyses. Since satisfactory correlation has been obtained at bench-scale level using 100 to 200 kG samples, an apparatus has been designed to analyze a coal stream of up to 50 ton/hour, at an electric power generating station

Effect of microwave radiation on coal flotation

Energy Technology Data Exchange (ETDEWEB)

Ozbayoglu, G.; Depci, T.; Ataman, N. [Middle East Technical University, Ankara (Turkey). Mining Engineering Department

2009-07-01

Most low-rank coals are high in moisture and acid functional groups, therefore showing poor floatability. Drying, which removes the water molecules trapped in the pores and adsorbed at the surface of coal, decreases the hydrophilic character and improves the floatability. Microwave heating, whose simplest application is drying, was applied at 0.9 kW power level for 60 sec exposure time in the experiments to decrease the moisture content of coal in order to enhance the hydrophobicity. The flotation tests of microwave-treated coal by using heptanol and octanol lead to a higher flotation yield and ash removal than original coal.

Thermal behaviour and microanalysis of coal subbituminus

Science.gov (United States)

Heriyanti; Prendika, W.; Ashyar, R.; Sutrisno

2018-04-01

Differential scanning calorimetry (DSC) and X-ray powder diffraction (XRD) is used to study the thermal behaviour of sub-bituminous coal. The DSC experiment was performed in air atmosphere up to 125 °C at a heating rate of 25 °C min1. The DSC curve showed that the distinct transitional stages in the coal samples studied. Thermal heating temperature intervals, peak and dissociation energy of the coal samples were also determined. The XRD analysis was used to evaluate the diffraction pattern and crystal structure of the compounds in the coal sample at various temperatures (25-350 °C). The XRD analysis of various temperatures obtained compounds from the coal sample, dominated by quartz (SiO2) and corundum (Al2O3). The increase in temperature of the thermal treatment showed a better crystal formation.

Biochemical removal of HAP precursors from coal. Quarterly technical progress report, April--June 1996

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

Analytical methods were finalized and all analyses completed on shake flask tests with Indiana No. 5 and Pittsburgh No. 8 coal. A column leaching-rotating biological contractor (RBC) unit was used to bioleach pyrite and hazardous air pollutant precursors from Pittsburgh No. 8 coal. Shake flask tests with Rosebud subbituminous coal were begun. In connection with upcoming slurry column reactor tests, coal was prepared and shipped to INEL, and a detailed work plan was developed for operation and sampling for the tests. A manuscript and poster was prepared for presentation at the PETC contractors conference.

Brown Coal Dewatering Using Poly (Acrylamide-Co-Potassium Acrylic Based Super Absorbent Polymers

Directory of Open Access Journals (Sweden)

Sheila Devasahayam

2015-09-01

Full Text Available With the rising cost of energy and fuel oils, clean coal technologies will continue to play an important role during the transition to a clean energy future. Victorian brown coals have high oxygen and moisture contents and hence low calorific value. This paper presents an alternative non evaporative drying technology for high moisture brown coals based on osmotic dewatering. This involves contacting and mixing brown coal with anionic super absorbent polymers (SAP which are highly crossed linked synthetic co-polymers based on a cross-linked copolymer of acryl amide and potassium acrylate. The paper focuses on evaluating the water absorption potential of SAP in contact with 61% moisture Loy Yang brown coal, under varying SAP dosages for different contact times and conditions. The amount of water present in Loy Yang coal was reduced by approximately 57% during four hours of SAP contact. The extent of SAP brown coal drying is directly proportional to the SAP/coal weight ratio. It is observed that moisture content of fine brown coal can readily be reduced from about 59% to 38% in four hours at a 20% SAP/coal ratio.

Influence of inorganic compounds on the combustion of coal. III. The effect of water of constitution of added compounds, moisture, and mineral matter in coal

Energy Technology Data Exchange (ETDEWEB)

Newall, H F

1939-01-01

The effects on the combustion rate from excess moisture and the addition of selected inorganic substances to powdered coals were determined. The catalytic effect of 19 known inorganic ash constituents on combustion rates was also examined. Alumina and silica were found to inhibit combustion while ferric oxide accelerated it. Titanium, Ge, and B oxides, along with gypsum and calcium phosphate, decreased the rate of combusion, while Ca, Mg, Mn, and V oxides increased combustion rates. Although several of the ash constituents in coal directly affected combustion rates, the effect of adding them to the coal prior to combustion did not correlate with the effect of the mineral matter already in the coal.

Geology and coal potential of Somaliland

Energy Technology Data Exchange (ETDEWEB)

M.Y. Ali [Petroleum Institute, Abu Dhabi (United Arab Emirates)

2009-07-01

Geological field mapping along with available geological and drilling data suggest that Somaliland (Northwestern Somalia) has favourable stratigraphy and structure for coal deposits. Lignitic to sub-bituminous coal deposits with ages from Jurassic to Oligocene-Miocene occur in various locations across the country including Hed-Hed valley south of Onkhor, Guveneh hills north of Las Dureh and Daban Basin southeast of Berbera. However, the coal occurrence at Hed-Hed has both the greatest thickness and highest quality. These deposits have the potential to provide an important alternative fuel resource which could alleviate the growing shortage of traditional fuels and assist in reducing the country's dependence on imported energy. However, further investigation, including drilling and laboratory analyses, still needs to be carried out, particularly on the Upper Cretaceous coal seams to evaluate the quality and resource potential of the deposits.

Revisiting Coos Bay, Oregon: A re-examination of funginite-huminite relationships in Eocene subbituminous coals

Energy Technology Data Exchange (ETDEWEB)

O' Keefe, Jennifer M.K. [Department of Earth and Space Sciences, Morehead State University, Morehead, KY (United States); Hower, James C. [University of Kentucky, Lexigton (United States). Center for Applied Energy Research

2011-01-01

Coal petrography has advanced significantly since Reinhardt Theissen and James Schopf pioneered the use of thin sections to examine coals from Coos Bay Oregon, and to many coal petrographers the nomenclature used in that study is irrelevant. The Schopf (1947) study was a ground-breaking examination of maceral relationships that need to be part of the working vocabulary of modern petrographers. To support this, a re-examination of the Coos Bay thin section collection was undertaken, using modern nomenclature for low-rank coals under reflected light. This particular collection was chosen in part because of the abundance of fungal material reported by Schopf. Fungal material in coal and its association with huminite/vitrinite macerals provides important information about the decompositional history of the coal and allows coal dominated by oxic processes to be differentiated from coal dominated by anoxic processes. In the Coos Bay samples, predominantly oxic intervals contain well-preserved fungi, including spores, sclerotia, and hyphae, while anoxic intervals contain no fungi. (author)

Application of computer graphics to generate coal resources of the Cache coal bed, Recluse geologic model area, Campbell County, Wyoming

Science.gov (United States)

Schneider, G.B.; Crowley, S.S.; Carey, M.A.

1982-01-01

Low-sulfur subbituminous coal resources have been calculated, using both manual and computer methods, for the Cache coal bed in the Recluse Model Area, which covers the White Tail Butte, Pitch Draw, Recluse, and Homestead Draw SW 7 1/2 minute quadrangles, Campbell County, Wyoming. Approximately 275 coal thickness measurements obtained from drill hole data are evenly distributed throughout the area. The Cache coal and associated beds are in the Paleocene Tongue River Member of the Fort Union Formation. The depth from the surface to the Cache bed ranges from 269 to 1,257 feet. The thickness of the coal is as much as 31 feet, but in places the Cache coal bed is absent. Comparisons between hand-drawn and computer-generated isopach maps show minimal differences. Total coal resources calculated by computer show the bed to contain 2,316 million short tons or about 6.7 percent more than the hand-calculated figure of 2,160 million short tons.

Comparison of Australasian tertiary coals based on resolution- enhanced solid-state /sup 13/C NMR spectra

Energy Technology Data Exchange (ETDEWEB)

Newman, R H; Davenport, S J

1986-04-01

/sup 13/C solid-state nuclear magnetic resonance spectroscopy was used to characterize 32 low-rank coals from New Zealand and Australia. A combination of high magnetic field (4.7 T) and resolution enhancement was used to extract spectral details beyond those seen in published spectra of coals of similar rank. Signal heights were used to characterize organic functional distributions. The spectra showed close similarities between Australian brown coals and low-rank New Zealand subbituminous coals, particularly those mined in the North Island. The spectra of New Zealand lignites all showed stronger signals from cellulose, methoxyl groups and phenols. Almost all of the New Zealand coals showed a relatively strong signal from polymethylene chains, compared with the Australian brown coals. This led to a prediction of higher alkene yields from pyrolysis of the New Zealand coals. Variations in phenolic substitution patterns were attributed to variations in the relative proportions of tannins and lignins in the depositional environments.

Rosebud syncoal partnership SynCoal{sup {reg_sign}} demonstration technology development update

Energy Technology Data Exchange (ETDEWEB)

Sheldon, R.W. [Rosebud SynCoal Company, Billings, MT (United States); Heintz, S.J. [Department of Energy, Pittsburgh, PA (United States)

1995-12-01

Rosebud SynCoal{reg_sign} Partnership`s Advanced Coal Conversion Process (ACCP) is an advanced thermal coal upgrading process coupled with physical cleaning techniques to upgrade high moisture, low-rank coals to produce a high-quality, low-sulfur fuel. The coal is processed through two vibrating fluidized bed reactors where oxygen functional groups are destroyed removing chemically bound water, carboxyl and carbonyl groups, and volatile sulfur compounds. After thermal upgrading, the SynCoal{reg_sign} is cleaned using a deep-bed stratifier process to effectively separate the pyrite rich ash. The SynCoal{reg_sign} process enhances low-rank western coals with moisture contents ranging from 2555%, sulfur contents between 0.5 and 1.5 %, and heating values between 5,500 and 9,000 Btu/lb. The upgraded stable coal product has moisture contents as low as 1 %, sulfur contents as low as 0.3%, and heating values up to 12,000 Btu/lb.

Catalytic multi-stage liquefaction of coal at HTI: Bench-scale studies in coal/waste plastics coprocessing

Energy Technology Data Exchange (ETDEWEB)

Pradhan, V.R.; Lee, L.K.; Stalzer, R.H. [Hydrocarbon Technologies, Inc., Lawrenceville, NJ (United States)] [and others

1995-12-31

The development of Catalytic Multi-Stage Liquefaction (CMSL) at HTI has focused on both bituminous and sub-bituminous coals using laboratory, bench and PDU scale operations. The crude oil equivalent cost of liquid fuels from coal has been curtailed to about $30 per barrel, thus achieving over 30% reduction in the price that was evaluated for the liquefaction technologies demonstrated in the late seventies and early eighties. Contrary to the common belief, the new generation of catalytic multistage coal liquefaction process is environmentally very benign and can produce clean, premium distillates with a very low (<10ppm) heteroatoms content. The HTI Staff has been involved over the years in process development and has made significant improvements in the CMSL processing of coals. A 24 month program (extended to September 30, 1995) to study novel concepts, using a continuous bench scale Catalytic Multi-Stage unit (30kg coal/day), has been initiated since December, 1992. This program consists of ten bench-scale operations supported by Laboratory Studies, Modelling, Process Simulation and Economic Assessments. The Catalytic Multi-Stage Liquefaction is a continuation of the second generation yields using a low/high temperature approach. This paper covers work performed between October 1994- August 1995, especially results obtained from the microautoclave support activities and the bench-scale operations for runs CMSL-08 and CMSL-09, during which, coal and the plastic components for municipal solid wastes (MSW) such as high density polyethylene (HDPE)m, polypropylene (PP), polystyrene (PS), and polythylene terphthlate (PET) were coprocessed.

Copyrolysis and hydropyrolysis of coal suspended in waste oil under pressure; Copirolisis e hidropirolisis a presion de mezclas de carbon y aceites pesados

Energy Technology Data Exchange (ETDEWEB)

Moliner, R. [CSIC, Zaragoza (Spain). Inst. de Carboquimica

1998-12-31

The present work studies the copyrolysis of a coal suspended in a waste oil under pressure, with short contact times. The main objective is to show the technical feasibility of the copyrolysis of coal and waste material slurries, in a fluidized bed and to evaluate the efficiency of the copyrolysis to improve quality and quantity of the products in relation to those obtained from the pyrolysis of coal. The work was started with three coals: Samca (subbituminous), HT51 (high-volatile bituminous) and Figaredo (low-volatile bituminous) and four aliphatic wastes from different origins: industrial hydraulic oils (AHU), lube oils (AMU), petroleum vacuum residuum (RP) and solutions of this residuum in vacuum gas-oil, RPG.

Low-grade coals: a review of some prospective upgrading technologies

Energy Technology Data Exchange (ETDEWEB)

Hassan Katalambula; Rajender Gupta [University of Alberta, Edmonton, AB (Canada). Department of Chemical and Materials Engineering

2009-07-15

There is a growing need of using low-grade coals because of higher quest for power generation. In the present carbon-constrained environment, there is a need of upgrading these coals in terms of moisture, ash, and/or other trace elements. The current paper reviews technologies used mainly categorized as drying for reducing moisture and cleaning the coal for reducing mineral content of coal and related harmful constituents, such as sulfur and mercury. The earliest upgrading of high-moisture lignite involved drying and manufacturing of briquettes. Drying technologies consist of both evaporative and non-evaporative (dewatering) types. The conventional coal cleaning used density separation in water medium. However, with water being a very important resource, conservation of water is pushing toward the development of dry cleaning of coal. There are also highly advanced coal-cleaning technologies that produce ultra-clean coals and produce coals with less than 0.1% of ash. The paper discusses some of the promising upgrading technologies aimed at improving these coals in terms of their moisture, ash, and other pollutant components. It also attempts to present the current status of the technologies in terms of development toward commercialization and highlights on problems encountered. It is obvious that still the upgrading goal has not been realized adequately. It can therefore be concluded that, because reserves for low-grade coals are quite plentiful, it is important to intensify efforts that will make these coals usable in an acceptable manner in terms of energy efficiency and environmental protection. 68 refs., 7 figs.

Coke from partially briquetted preheated coal mixtures

Energy Technology Data Exchange (ETDEWEB)

Belitskii, A.N.; Sklyar, M.G.; Toryanik, Eh.I.; Bronshtein, A.P.

1988-07-01

Analyzes effects of partial coal charge briquetting on coking and on quality of coke for metallurgy. Effects of mixing hot coal briquets on temperature and moisture of coal were investigated on an experimental scale in a coking plant. Coal with a moisture content of 12% was used. Coking mixture consisted of 30% briquets and 70% crushed coal. Fifteen minutes after briquet mixing with coal, the mean coal charge temperature increased to 100-105 C and moisture content was lower than 2-5%. Results of laboratory investigations were verified by tests on a commercial scale. Experiments showed briquetting of weakly caking or non-caking coal charge components to be an efficient way of preventing coke quality decline. Adding 15-20% briquets consisting of weakly caking coal did not influence coke quality. Mixing hot coal briquets reduced moisture content in crushed coal, increased its temperature and reduced coking time.

Understanding selected trace elements behavior in a coal-fired power plant in Malaysia for assessment of abatement technologies.

Science.gov (United States)

Mokhtar, Mutahharah M; Taib, Rozainee M; Hassim, Mimi H

2014-08-01

The Proposed New Environmental Quality (Clean Air) Regulation 201X (Draft), which replaces the Malaysia Environmental Quality (Clean Air) 1978, specifies limits to additional pollutants from power generation using fossil fuel. The new pollutants include Hg, HCl, and HF with limits of 0.03, 100, and 15 mg/N-m3 at 6% O2, respectively. These pollutants are normally present in very small concentrations (known as trace elements [TEs]), and hence are often neglected in environmental air quality monitoring in Malaysia. Following the enactment of the new regulation, it is now imperative to understand the TEs behavior and to assess the capability of the existing abatement technologies to comply with the new emission limits. This paper presents the comparison of TEs behavior of the most volatile (Hg, Cl, F) and less volatile (As, Be, Cd, Cr, Ni, Se, Pb) elements in subbituminous and bituminous coal and coal combustion products (CCP) (i.e., fly ash and bottom ash) from separate firing of subbituminous and bituminous coal in a coal-fired power plant in Malaysia. The effect of air pollution control devices configuration in removal of TEs was also investigated to evaluate the effectiveness of abatement technologies used in the plant. This study showed that subbituminous and bituminous coals and their CCPs have different TEs behavior. It is speculated that ash content could be a factor for such diverse behavior In addition, the type of coal and the concentrations of TEs in feed coal were to some extent influenced by the emission of TEs in flue gas. The electrostatic precipitator (ESP) and seawater flue gas desulfurization (FGD) used in the studied coal-fired power plant were found effective in removing TEs in particulate and vapor form, respectively, as well as complying with the new specified emission limits. Implications: Coals used by power plants in Peninsular Malaysia come from the same supplier (Tenaga Nasional Berhad Fuel Services), which is a subsidiary of the Malaysia

Sequence stratigraphy, organic petrology and chemistry applied to the upper and lower coal seams in the Candiota Coalfield, Parana Basin, RS, Brazil

Energy Technology Data Exchange (ETDEWEB)

Oliveira, J.S. de; Kalkreuth, W. [Instituto de Geociencias, UFRGS, Porto Alegre (Brazil)

2010-12-01

The Permian age coal seams in the Candiota Coalfield represent the largest coal deposit of the country. Currently two seams are mined, called ''Camada Candiota Superior'' and ''Camada Candiota Inferior''. The other coal seams of the coalfield, seams S1-S9 (upper seams) and I1-I5 (lower seams) have as yet not been exploited. The objective of this paper is to perform a detailed sequence stratigraphic, petrologic and chemical study of the upper and lower coal seams, thereby generating data for assisting in the development and better use of the coal-bearing interval. The methodology includes application of the concepts of sequence stratigraphy, which includes the lithological interpretation of the core to establish the depositional environments and genetic correlation between facies associations to define parasequences and bounding surfaces; coal petrology (analysis of the reflectance of vitrinite, determination of the petrographic composition of the coals by maceral analyses), and chemical analyses such as sulphur determination, proximate analyses (ash, moisture, volatile matter, and fixed carbon), and elemental analyses. Three main depositional systems were so far identified: alluvial fan, fluvial system, lagoonal estuary system. This study shows that coal development was controlled by accommodation/accumulation rates, with coal seams with greater thickness and lateral continuity being formed within the transgressive systems tract (lagoonal depositional system) of parasequence 2 (PS2), indicating that the accumulation rates of the peat and distribution of the coal seams were controlled by stratigraphic setting. Vitrinite reflectances for the upper and lower coal seams are indicative of subbituminous rank (Rrandom = 0.36-0.47%), with evidence that anomalously low reflectance values are related to high mineral-matter contents. Maceral composition is highly variable, with some coal seams being extremely rich in inertinite (up to

Development of the first coal seam gas exploration program in Indonesia: Reservoir properties of the Muaraenim Formation, south Sumatra

Energy Technology Data Exchange (ETDEWEB)

Sosrowidjojo, I.B. [R and D Centre for Oil and Gas Technology, LEMIGAS, Jakarta (Indonesia); Saghafi, A. [CSIRO Energy Technology, P O Box 330, Newcastle, NSW, 2300 (Australia)

2009-09-01

The Late Miocene Muaraenim Formation in southern Sumatra contains thick coal sequences, mostly of low rank ranging from lignite to sub-bituminous, and it is believed that these thick low rank coals are the most prospective for the production of coal seam gas (CSG), otherwise known as coalbed methane (CBM), in Indonesia. As part of a major CSG exploration project, gas exploration drilling operations are being undertaken in Rambutan Gasfields in the Muaraenim Formation to characterize the CSG potential of the coals. The first stage of the project, which is described here, was designed to examine the gas reservoir properties with a focus on coal gas storage capacity and compositional properties. Some five CSG exploration boreholes were drilled in the Rambutan Gasfield, south of Palembang. The exploration boreholes were drilled to depths of {proportional_to} 1000 m into the Muaraenim Formation. Five major coal seams were intersected by these holes between the depths of 450 and 1000 m. The petrography of coal samples collected from these seams showed that they are vitrinite rich, with vitrinite contents of more than 75% (on a mineral and moisture free basis). Gas contents of up to 5.8 m{sup 3}/t were measured for the coal samples. The gas desorbed from coal samples contain mainly methane (CH{sub 4}) ranging from 80 to 93% and carbon dioxide (CO{sub 2}) ranging from 6 to 19%. The composition of the gas released into the production borehole/well is, however, much richer in CH{sub 4} with about 94 to 98% CH{sub 4} and less than 5% CO{sub 2}. The initial results of drilling and reservoir characterization studies indicate suitable gas recovery parameters for three of the five coal seams with a total thickness of more than 30 m. (author)

A compact XRF unit for determining total sulphur content in coals

International Nuclear Information System (INIS)

Sumitra, T.; Chankow, N.; Punnachaiya, S.; Srisatit, S.

1994-01-01

A microcomputer based x-ray fluorescence (XRF) unit was developed for off-line determination of total sulphur content in coal samples. The unit consisted of the x-ray exciting/measuring set and the microcomputer with a plug-in interface card. An Fe-55 radioisotope was used as the exciting source while a krypton-filled proportional counter was used to measure x-rays from the samples. The x-ray spectrum was simultaneously displayed on the microcomputer screen. For quantitative determination of sulphur, the intensities of sulphur K x-rays as well as calcium K x-rays and scattered x-rays were taken into account. The unit was tested with finely-ground, dried and compressed lignite, subbituminous and bituminous samples. If was found that for low-calcium coals, the results were in good agreement with those obtained from the standard chemical analysis method within ± 0.2% and within ± 0.5%S for high-calcium coals. 2 refs., 2 tabs., 3 figs

Effect of mineral matter on coal self-heating rate

Energy Technology Data Exchange (ETDEWEB)

B. Basil Beamish; Ahmet Arisoy [University of Queensland, Brisbane, Qld. (Australia). School of Engineering

2008-01-15

Adiabatic self-heating tests have been conducted on subbituminous coal cores from the same seam profile, which cover a mineral matter content range of 11.2-71.1%. In all cases the heat release rate does not conform to an Arrhenius kinetic model, but can best be described by a third order polynomial. Assessment of the theoretical heat sink effect of the mineral matter in each of the tests reveals that the coal is less reactive than predicted using a simple energy conservation equation. There is an additional effect of the mineral matter in these cases that cannot be explained by heat sink alone. The disseminated mineral matter in the coal is therefore inhibiting the oxidation reaction due to physicochemical effects. 14 refs., 5 figs., 5 tabs.

Fast-neutron and gamma-ray transmission technique for the on-line determination of moisture in coal and coke

International Nuclear Information System (INIS)

Sowerby, B.D.; Millen, M.J.; Rafter, P.T.

1988-01-01

A fast neutron and γ-ray transmission technique is being developed for the on-line analysis of moisture. Calculations show that the technique is capable of determining coke moisture to better than 0.2 wt% over a wide range of coke thicknesses. The favoured technique uses a thick Li-glass detector surrounded by a neutron moderator to determine simultaneously the fast neutron and γ-ray intensities. Laboratory measurements on single coke samples showed that moisture can be determined to within 0.2 wt% over the range 3-13 wt% moisture and 300-500 mm thickness. Measurements on a range of coke samples showed that the increase in r.m.s. error due to bound H variations is less than about 0.4 wt% moisture. Applications of the technique, to moisture determination in black and brown coal are also investigated, both by calculation and experiment. Further potential applications of the technique are discussed, including the determination of C in steel. (author)

Use of structural parameters of Canadian coals to follow coalification process

Energy Technology Data Exchange (ETDEWEB)

Furimsky, E.; Charland, J.-P.; Dureau, R.; Kalkreuth, W.; Wieschenkaemper, I. (CANMET, Ottawa, ON (Canada). Energy Research Laboratories)

1991-06-01

A series of Canadian coals was used to evaluate the structural parameters determined by the FTIR spectroscopy and the apparent aromaticity determined by solid state {sup 13}C NMR spectroscopy as coalification indicators. The results support the existence of two main coalification regions, i.e. the first involving lignite-subbituminous-high volatile bituminous stages and the second which begins with high volatile bituminous coals and ends with anthracite. The deoxygenation is the main reaction in the first region whereas the steady increase in apparent aromaticity is the most evident process in the second. The hydroxylic oxygen is a good indicator to distinguish between different coalification stages in the first region. The amount of three and more hydrogens attached to aromatic units exhibited a linear trend with both apparent aromaticity and mean reflectance for the coalification range from lignite to anthracite. 15 refs., 10 figs.

Coal geology and assessment of coal resources and reserves in the Powder River Basin, Wyoming and Montana

Science.gov (United States)

Luppens, James A.; Scott, David C.

2015-01-01

This report presents the final results of the first assessment of both coal resources and reserves for all significant coal beds in the entire Powder River Basin, northeastern Wyoming and southeastern Montana. The basin covers about 19,500 square miles, exclusive of the part of the basin within the Crow and Northern Cheyenne Indian Reservations in Montana. The Powder River Basin, which contains the largest resources of low-sulfur, low-ash, subbituminous coal in the United States, is the single most important coal basin in the United States. The U.S. Geological Survey used a geology-based assessment methodology to estimate an original coal resource of about 1.16 trillion short tons for 47 coal beds in the Powder River Basin; in-place (remaining) resources are about 1.15 trillion short tons. This is the first time that all beds were mapped individually over the entire basin. A total of 162 billion short tons of recoverable coal resources (coal reserve base) are estimated at a 10:1 stripping ratio or less. An estimated 25 billion short tons of that coal reserve base met the definition of reserves, which are resources that can be economically produced at or below the current sales price at the time of the evaluation. The total underground coal resource in coal beds 10–20 feet thick is estimated at 304 billion short tons.

Investigation of a high pressure oxy-coal process

Energy Technology Data Exchange (ETDEWEB)

Renz, U. [RWTH Aachen Univ. (Germany). Inst. of Heat and Mass Transfer

2013-07-01

A study was conducted to investigate the feasibility of an oxy-coal process, which is pressurized to a combustion pressure of 80 bar. At that pressure the water-vapor can be separated economically from the CO{sub 2}/H{sub 2}O flue gases, either by nucleate condensation or by condensation on cooled surfaces in condenser heat exchangers at a temperature of about 300 C. The heat of condensation can be recaptured to preheat the boiler feed water. So the number of economizers is drastically reduced compared to a conventional steam cycle. Another interesting feature of the high pressure oxy-coal process is the fact, that low rank coal with high moisture content can be fired. Such a process at a pressure of about 80 bar is currently investigated by Babcock, USA, as the ThermoEnergy Integrated Power System (TIPS) and will be analyzed in the present paper. A known disadvantage of the oxy-coal processes is the large recirculating flue gas stream to control the combustion temperature, and which need large pipes and heavy recirculation fans. This disadvantage could be avoided if instead of flue gas a part of the condensed water from the condenser heat exchangers is recirculated. Within the present study both types of processes have been simulated and for an electric power output of about 220 MW. Furthermore, results of CFD simulations of a pressurized 250 MW combustor with a single swirl burner and flue gas recirculation will be presented.

Integrated method of RS and GPR for monitoring the changes in the soil moisture and groundwater environment due to underground coal mining

Science.gov (United States)

Bian, Zhengfu; Lei, Shaogang; Inyang, Hilary I.; Chang, Luqun; Zhang, Richen; Zhou, Chengjun; He, Xiao

2009-03-01

Mining affects the environment in different ways depending on the physical context in which the mining occurs. In mining areas with an arid environment, mining affects plants’ growth by changing the amount of available water. This paper discusses the effects of mining on two important determinants of plant growth—soil moisture and groundwater table (GWT)—which were investigated using an integrated approach involving a field sampling investigation with remote sensing (RS) and ground-penetrating radar (GPR). To calculate and map the distribution of soil moisture for a target area, we initially analyzed four models for regression analysis between soil moisture and apparent thermal inertia and finally selected a linear model for modeling the soil moisture at a depth 10 cm; the relative error of the modeled soil moisture was about 6.3% and correlation coefficient 0.7794. A comparison of mined and unmined areas based on the results of limited field sampling tests or RS monitoring of Landsat 5-thermatic mapping (TM) data indicated that soil moisture did not undergo remarkable changes following mining. This result indicates that mining does not have an effect on soil moisture in the Shendong coal mining area. The coverage of vegetation in 2005 was compared with that in 1995 by means of the normalized difference vegetation index (NDVI) deduced from TM data, and the results showed that the coverage of vegetation in Shendong coal mining area has improved greatly since 1995 because of policy input RMB¥0.4 per ton coal production by Shendong Coal Mining Company. The factor most affected by coal mining was GWT, which dropped from a depth of 35.41 m before mining to a depth of 43.38 m after mining at the Bulianta Coal Mine based on water well measurements. Ground-penetrating radar at frequencies of 25 and 50 MHz revealed that the deepest GWT was at about 43.4 m. There was a weak water linkage between the unsaturated zone and groundwater, and the decline of water table

Characteristics of carbonized sludge for co-combustion in pulverized coal power plants

International Nuclear Information System (INIS)

Park, Sang-Woo; Jang, Cheol-Hyeon

2011-01-01

Co-combustion of sewage sludge can destabilize its combustion profile due to high volatility, which results in unstable flame. We carried out fuel reforming for sewage sludge by way of carbonization at pyrolysis temperature of 300-500 deg. C. Fuel characteristics of carbonized sludge at each temperature were analyzed. As carbonization temperature increased, fuel ratio increased, volatile content reduced, and atomic ratio relation of H/C and O/C was similar to that of lignite. The analysis result of FT-IR showed the decrease of aliphatic C-H bond and O-C bond in carbonization. In the analysis result of TG-DTG, the thermogravimetry reduction temperature of carbonized sludge (CS400) was proven to be higher than that of dried sludge, but lower than that of sub-bituminous coal. Hardgrove grindability index increased in proportion to fuel ratio increase, where the carbonized sludge value of 43-110 was similar or higher than the coal value of 49-63. As for ash deposits, slagging and fouling index were higher than that of coal. When carbonized sludge (CS400) and coal were co-combusted in 1-10% according to calorific value, slagging tendency was low in all conditions, and fouling tendency was medium or high according to the compositions of coal.

Microbial diversity of western Canadian subsurface coal beds and methanogenic coal enrichment cultures

Energy Technology Data Exchange (ETDEWEB)

Penner, Tara J.; Foght, Julia M. [Department of Biological Sciences, University of Alberta, Edmonton, Alberta (Canada); Budwill, Karen [Carbon and Energy Management, Alberta Innovates-Technology Futures, 250 Karl Clark Road, Edmonton, Alberta (Canada)

2010-05-01

Coalbed methane is an unconventional fuel source associated with certain coal seams. Biogenic methane can comprise a significant portion of the gas found in coal seams, yet the role of microbes in methanogenesis in situ is uncertain. The purpose of this study was to detect and identify major bacterial and archaeal species associated with coal sampled from sub-bituminous methane-producing coal beds in western Canada, and to examine the potential for methane biogenesis from coal. Enrichment cultures of coal samples were established to determine how nutrient amendment influenced the microbial community and methane production in the laboratory. 16S rRNA gene clone libraries were constructed using DNA extracted and amplified from uncultured coal samples and from methanogenic coal enrichment cultures. Libraries were screened using restriction fragment length polymorphism, and representative clones were sequenced. Most (> 50%) of the bacterial sequences amplified from uncultured coal samples were affiliated with Proteobacteria that exhibit nitrate reduction, nitrogen fixation and/or hydrogen utilization activities, including Pseudomonas, Thauera and Acidovorax spp., whereas enrichment cultures were dominated by Bacteroidetes, Clostridia and/or Lactobacillales. Archaeal 16S rRNA genes could not be amplified from uncultured coal, suggesting that methanogens are present in coal below the detection levels of our methods. However, enrichment cultures established with coal inocula produced significant volumes of methane and the archaeal clone libraries were dominated by sequences closely affiliated with Methanosarcina spp. Enrichment cultures incubated with coal plus organic nutrients produced more methane than either nutrient or coal supplements alone, implying that competent methanogenic consortia exist in coal beds but that nutrient limitations restrict their activity in situ. This report adds to the scant literature on coal bed microbiology and suggests how microbes may be

Direct liquefaction of plastics and coprocessing of coal with plastics

Energy Technology Data Exchange (ETDEWEB)

Huffman, G.P.; Feng, Z.; Mahajan, V. [Univ. of Kentucky, Lexington, KY (United States)

1995-12-31

The objectives of this work were to optimize reaction conditions for the direct liquefaction of waste plastics and the coprocessing of coal with waste plastics. In previous work, the direct liquefaction of medium and high density polyethylene (PE), polypropylene (PPE), poly(ethylene terephthalate) (PET), and a mixed plastic waste, and the coliquefaction of these plastics with coals of three different ranks was studied. The results established that a solid acid catalyst (HZSM-5 zeolite) was highly active for the liquefaction of the plastics alone, typically giving oil yields of 80-95% and total conversions of 90-100% at temperatures of 430-450 {degrees}C. In the coliquefaction experiments, 50:50 mixtures of plastic and coal were used with a tetralin solvent (tetralin:solid = 3:2). Using approximately 1% of the HZSM-5 catalyst and a nanoscale iron catalyst, oil yields of 50-70% and total conversion of 80-90% were typical. In the current year, further investigations were conducted of the liquefaction of PE, PPE, and a commingled waste plastic obtained from the American Plastics Council (APC), and the coprocessing of PE, PPE and the APC plastic with Black Thunder subbituminous coal. Several different catalysts were used in these studies.

Characterization of products from pyrolysis of coal with the addition of polyethylene terephthalate

Czech Academy of Sciences Publication Activity Database

Havelcová, Martina; Bičáková, Olga; Sýkorová, Ivana; Weishauptová, Zuzana; Melegy, A.

2016-01-01

Roč. 154, DEC 15 (2016), 123-131 ISSN 0378-3820 R&D Projects: GA ČR(CZ) GA13-18482S Grant - others:OPPK(XE) CZ.2.16/3.1.00/21538 Program:OPPK Institutional support: RVO:67985891 Keywords : pyrolysis * sub-bituminous coal * polyethylene terephthalate * coke Subject RIV: DD - Geochemistry Impact factor: 3.752, year: 2016

Enhancing the Properties of Coal Briquette Using Spear Grass (Imperata Cylindrica

Directory of Open Access Journals (Sweden)

Adaora Stellamaris OGBUAGU

2010-12-01

Full Text Available Studies have been carried out on utilizing agricultural wastes (spear grass to enhance the properties of coal briquette. The proximate analysis of the plant material was carried out alongside with a sample of coal (sub-bituminous coal. Briquettes of different compositions were produced by blending the plant material with the coal at various concentrations: 0%, 10%, 20%, 30%, 40%, 50% and 100%, using cassava starch as a binder and calcium hydroxide (Ca(OH2 as desulfurizing agent. The properties of the briquettes were compared. It was found that the ignition, burning rate and reduction in smoke emission showed improvement with increase in biomass concentration. Compressive strength and cooking efficiency (water boiling time and specific fuel consumption showed initial improvement and rendered to decrease with briquette containing 30% biomass.

Low-rank coal study: national needs for resource development. Volume 3. Technology evaluation

Energy Technology Data Exchange (ETDEWEB)

1980-11-01

Technologies applicable to the development and use of low-rank coals are analyzed in order to identify specific needs for research, development, and demonstration (RD and D). Major sections of the report address the following technologies: extraction; transportation; preparation, handling and storage; conventional combustion and environmental control technology; gasification; liquefaction; and pyrolysis. Each of these sections contains an introduction and summary of the key issues with regard to subbituminous coal and lignite; description of all relevant technology, both existing and under development; a description of related environmental control technology; an evaluation of the effects of low-rank coal properties on the technology; and summaries of current commercial status of the technology and/or current RD and D projects relevant to low-rank coals.

Cooperative research in coal liquefaction. Final report, May 1, 1992--April 30, 1993

Energy Technology Data Exchange (ETDEWEB)

Huffman, G.P. [ed.

1996-03-01

Research on sulfate and metal (Mo, Sn) promoted Fe{sub 2}O{sub 3} catalysts in the current year focused on optimization of conditions. Parameters varied included temperature, solvent, solvent-to-coal ratio, and the effect of presulfiding versus in situ sulfiding. Oil yields were found to increase approximately proportionately with both temperature and solvent-to-coal ratio. The donor solvent, tetralin, proved to give better total conversion and oil yields than either 1-methylnaphthalene or Wilsonville recycle oil. A significant enhancement of both total liquefaction yields and oil yields from lignites and subbituminous coals has been achieved by incorporating iron into the coal matrix by cation exchange. A study has been conducted on the synthesis of iron, molybdenum, and tungsten catalysts using a laser pyrolysis technique.

Report on the achievements in the Sunshine Project in fiscal 1987. Surveys on coal selection and coal types (Surveys on coal resources for liquefaction); 1987 nendo tanshu sentei chosa tanshu chosa seika hokokusho. Ekikayo sekitan shigen chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-03-01

The survey purpose is to identify availability of coal resources for liquefaction in major coal producing countries in the Pacific basin area. Therefore, collection is carried out on such data as coal existing conditions, coal qualities, production quantities, and infrastructures on coal mines being operated and projects under development or investigation. Coal samples are collected in wide range and exhaustively unbiased to particular coal fields and mines to acquire data to perform selection and evaluation of coals that can be fed to coal liquefying plants. The present survey was intended to acquire fundamental data for the liquefying coal selection, such as coal existing conditions, natures, and infrastructures for the coal resources, taking up as the survey object countries the State of Alaska, U.S.A. and Indonesia. The coal types as the object of the survey are mainly sub-bituminous coal, and additionally brown coal and partly bituminous coal. The amount of coal deposit as the subject of the investigation is 100 million tons or more as the verified reserve. The subject areas cover coal mines in the State of Alaska, U.S.A. (Northern Alaska, Nenana, Beluga, and Matanuska coal fields), and Indonesia (the Sumatra and Kalimantan islands). The survey items are made up of 14 items (see the coal mine survey tables in JN0040851). (NEDO)

The Mesaba Energy Project: Clean Coal Power Initiative, Round 2

Energy Technology Data Exchange (ETDEWEB)

Stone, Richard; Gray, Gordon; Evans, Robert

2014-07-31

The Mesaba Energy Project is a nominal 600 MW integrated gasification combine cycle power project located in Northeastern Minnesota. It was selected to receive financial assistance pursuant to code of federal regulations (?CFR?) 10 CFR 600 through a competitive solicitation under Round 2 of the Department of Energy?s Clean Coal Power Initiative, which had two stated goals: (1) to demonstrate advanced coal-based technologies that can be commercialized at electric utility scale, and (2) to accelerate the likelihood of deploying demonstrated technologies for widespread commercial use in the electric power sector. The Project was selected in 2004 to receive a total of $36 million. The DOE portion that was equally cost shared in Budget Period 1 amounted to about $22.5 million. Budget Period 1 activities focused on the Project Definition Phase and included: project development, preliminary engineering, environmental permitting, regulatory approvals and financing to reach financial close and start of construction. The Project is based on ConocoPhillips? E-Gas? Technology and is designed to be fuel flexible with the ability to process sub-bituminous coal, a blend of sub-bituminous coal and petroleum coke and Illinois # 6 bituminous coal. Major objectives include the establishment of a reference plant design for Integrated Gasification Combined Cycle (?IGCC?) technology featuring advanced full slurry quench, multiple train gasification, integration of the air separation unit, and the demonstration of 90% operational availability and improved thermal efficiency relative to previous demonstration projects. In addition, the Project would demonstrate substantial environmental benefits, as compared with conventional technology, through dramatically lower emissions of sulfur dioxide, nitrogen oxides, volatile organic compounds, carbon monoxide, particulate matter and mercury. Major milestones achieved in support of fulfilling the above goals include obtaining Site, High Voltage

Development of the neutron technology for measuring the moisture content in China

International Nuclear Information System (INIS)

Zhao Jingwu; Liu Shengkang; Zhang Zhiping

2011-01-01

According to measuring mode (in-hopper, surface, sampling neutron moisture gauge), the development and application of neutron moisture gauge in china were introduced, which include the following course from only measuring moisture content of soil to monitoring moisture content of farmland and saving water for irrigating farmland, from measuring moisture content of pellet to coke and coal material, from only measuring moisture content to computerized neutron moisture gauges with density compensation and o f high precision. (authors)

Production of low ash coal by thermal extraction with N-methyl-2-pyrrolidinone

Energy Technology Data Exchange (ETDEWEB)

Do Kim, S.; Woo, K.J.; Jeong, S.K.; Rhim, Y.J.; Lee, S.H. [Korean Institute for Energy Research, Taejon (Republic of Korea). Clean Coal Technological Research Center

2008-07-15

Present study was conducted for the purpose of producing low ash coal from LRC (low rank coals) such as lignite and sub-bituminous coal through thermal extraction using polar solvent. Extraction from bituminous coal was also investigated for comparison. NMP as a polar solvent was used. The ratio of coal to solvent was adjusted as 1:10. Experimental conditions were established which include the extraction temperature of 200-430{sup o}C, initial applied pressure of 1-20 bar and extraction time of 0.5-2 hr were used. Extraction yield and ash content of extracted and residual coal were measured. The extraction yield increased with the increase of extraction temperature, and the ash content of extracted coal decreased below 0.4% at 400{sup o}C from the raw coal samples that have the ash contents of 4-6%. According to the analysis of experiments results, fixed carbon and calorific value increased, and H/C and O/C decreased.

Exploratory Research on Novel Coal

Energy Technology Data Exchange (ETDEWEB)

Winschel, R.A.; Brandes, S.D.

1998-05-01

The report presents the findings of work performed under DOE Contract No. DE-AC22 -95PC95050, Task 3 - Flow Sheet Development. A novel direct coal liquefaction technology was investigated in a program being conducted by CONSOL Inc. with the University of Kentucky Center for Applied Energy Research and LDP Associates. The process concept explored consists of a first-stage coal dissolution step in which the coal is solubilized by hydride ion donation. In the second stage, the products are catalytically upgraded to refinery feedstocks. Integrated first-stage and solids-separation steps were used to prepare feedstocks for second-stage catalytic upgrading. An engineering and economic evaluation was conducted concurrently with experimental work throughout the program. Parameters were established for a low-cost, low-severity first-stage reaction system. A hydride ion reagent system was used to effect high coal conversions of Black Thunder Mine Wyoming subbituminous coal. An integrated first-stage and filtration step was successfully demonstrated and used to produce product filtrates with extremely low solids contents. High filtration rates previously measured off-line in Task 2 studies were obtained in the integrated system. Resid conversions of first-stage products in the second stage were found to be consistently greater than for conventional two-stage liquefaction resids. In Task 5, elementally balanced material balance data were derived from experimental results and an integrated liquefaction system balance was completed. The economic analysis indicates that the production of refined product (gasoline) via this novel direct liquefaction technology is higher than the cost associated with conventional two-stage liquefaction technologies. However, several approaches to reduce costs for the conceptual commercial plant were recommended. These approaches will be investigated in the next task (Task 4) of the program.

Novel bimetallic dispersed catalysts for temperature-programmed coal liquefaction. Final report

Energy Technology Data Exchange (ETDEWEB)

Chunshan Song; Schobert, H.H.; Parfitt, D.P. [and others

1997-11-01

Development of new catalysts is a promising approach to more efficient coal liquefaction. It has been recognized that dispersed catalysts are superior to supported catalysts for primary liquefaction of coals, because the control of initial coal dissolution or depolymerization requires intimate contact between the catalyst and coal. This research is a fundamental and exploratory study on catalytic coal liquefaction, with the emphasis on exploring novel bimetallic dispersed catalysts for coal liquefaction and the effectiveness of temperature-programmed liquefaction using dispersed catalysts. The primary objective of this research was to explore novel bimetallic dispersed catalysts from organometallic molecular precursors, that could be used in low concentrations but exhibit relatively high activity for efficient hydroliquefaction of coals under temperature-programmed conditions. We have synthesized and tested various catalyst precursors in liquefaction of subbituminous and bituminous coals and in model compound studies to examine how do the composition and structure of the catalytic precursors affect their effectiveness for coal liquefaction under different reaction conditions, and how do these factors affect their catalytic functions for hydrogenation of polyaromatic hydrocarbons, for cleavage of C-C bonds in polycyclic systems such as 4-(1-naphthylmethyl)bibenzyl, for hydrogenolysis of C-O bond such as that in dinaphthylether, for hydrodeoxygenation of phenolic compounds and other oxygen-containing compounds such as xanthene, and for hydrodesulfurization of polycyclic sulfur compounds such as dibenzothiophene. The novel bimetallic and monometallic precursors synthesized and tested in this project include various Mo- and Fe-based compounds.

Slagging in a pulverised-coal-fired boiler

Energy Technology Data Exchange (ETDEWEB)

Devir, G.P.; Pohl, J.H.; Creelman, R.A. [University of Queensland, St. Lucia, Qld. (Australia). Dept. of Chemical Engineering

2000-07-01

This paper describes a technique to evaluate the severity of slagging of a coal in a pulverised-coal-fired boiler. There are few data in the literature on the nature of in-situ boiler slags, their rate of growth and/or their strength properties relevant to sootblowing. The latter is thought to be of more concern to boiler operators and gives rise to the significance of selecting suitable strength tests. As well as standardised methods for characterising pulverised coal performance in a boiler, several novel and less popular techniques are discussed in detail. A suite of three sub-bituminous coals from the Callide Coalfields, Biloela (600 km north of Brisbane), has been selected for slagging tests in the 350 MW{sub e} units of Callide 'B' power station. Disposable air-cooled mild steel slagging probes have been constructed to simulate the conditions for deposit formation in the boiler region. To date, tests for one of these coals has been completed and preliminary results are presented. Once testing for the remaining coals has been completed, it is anticipated that the differences exhibited in deposit growth and strength may be correlated with typical variations in physical and chemical properties of the pulverised coal.

The ENDESA group in Spanish coal mining. El Grupo ENDESA en la mineria espanola del carbon

Energy Technology Data Exchange (ETDEWEB)

1987-01-01

The ENDESA group, the largest producer of coal and electricity in Spain, plays an important role in the energy sector within the sub-divisions of coal and electricity. ENDESA, the principal company within the group, was created in 1944 with the immediate objective of constructing the Compostilla I thermal power station in Ponferrada (Leon), in order to make use of the high quality coal in the Bierzo coalfield, for which, at that time, there was no demand. Later, in 1972, ENDESA acquired the brown lignite deposit of As Pontes (La Coruna) for opencast working and the sub-bituminous coal deep mines of Andorra (Teruel). The two thermal power stations were constructed on the mine sites to use the coal extracted. ENCASUR with deposits in Penarroya (Cordoba) and Puertollano (Ciudad Real) and GESA, through its subsidiary LIGNITOS SA in Mallorca, make up the coal mining activities of the ENDESA group. The role of the ENDESA group is defined by its production levels (41% of the national level), its purchases of indigenous coal (30% of the non-ENDESA group total) and of imported coal (61% of the total imported for use in power stations). In total, this means that the ENDESA group represents 51% of the Spanish coal market. 54 figs., 20 tabs.

Cleaning and dewatering fine coal

Science.gov (United States)

Yoon, Roe-Hoan; Eraydin, Mert K.; Freeland, Chad

2017-10-17

Fine coal is cleaned of its mineral matter impurities and dewatered by mixing the aqueous slurry containing both with a hydrophobic liquid, subjecting the mixture to a phase separation. The resulting hydrophobic liquid phase contains coal particles free of surface moisture and droplets of water stabilized by coal particles, while the aqueous phase contains the mineral matter. By separating the entrained water droplets from the coal particles mechanically, a clean coal product of substantially reduced mineral matter and moisture contents is obtained. The spent hydrophobic liquid is separated from the clean coal product and recycled. The process can also be used to separate one type of hydrophilic particles from another by selectively hydrophobizing one.

Proceedings of the third annual underground coal conversion symposium

Energy Technology Data Exchange (ETDEWEB)

None

1977-01-01

The Third Annual Underground Coal Conversion Symposium was held at Fallen Leaf Lake, CA, June 6--9, 1977. It was sponsored by the U.S. Department of Energy and hosted by Lawrence Livermore Laboratory. Forty-one papers have been entered individually into EDB and ERA; ten papers had been entered previously from other sources. The papers cover the in-situ gasification of lignite, subbituminous coal and bituminous coal, in flat lying seams and a steeply dipping beds, at moderate and at greater depths, and describe various technologies of (borehole linking, well spacings, gasifying agents (air, oxygen, steam, hydrogen, including mixtures). Measuring instruments for diagnostic and process control purposes are described. Environmental impacts (ground subsidence and possible groundwater pollution) are the subject of several papers. Finally, mathematical modelling and projected economics of the process are developed. (LTN)

Liquefaction of Warukin Formation Coal, Barito Basin, South Kalimantan on Low Pressure and Low Temperature

Directory of Open Access Journals (Sweden)

Edy Nursanto

2013-06-01

Full Text Available Research focusing on the quality of coal in Warukin Formation has been conducted in coal outcrops located on Tabalong area, particularly in 3 coal seams, namely Wara 120 which consists of low rank coal (lignite. Meanwhile, coals in seam Tutupan 210 and Paringin 712 are medium rank coal (sub-bituminous. Coal liquefaction is conducted in an autoclave on low pressure and temperature. Pressure during the process is 14 psi and temperature is 120oC. Catalyst used are alumina, hydrogen donor NaOH and water solvent. Liquefaction is conducted in three times variables of 30 minutes, 60 minutes and 90 minutes. This process shows following yield : Wara seam 120: 25.37% - 51.27%; Tutupan seam 210: 3.02%-15.45% and seam Paringin 712:1.99%-11.95%. The average result of yield shows that coals in seam Wara has higher yield conversion than coals in seam Tutupan and Paringin.

The effect of solvent swelling for the production of ashless coal

Energy Technology Data Exchange (ETDEWEB)

Aylin Kurman; Sultan Giray; Ozgur Sonmez [Cukurova University, Adana (Turkey). Chemistry Department, Art& Science Faculty

2005-07-01

Two Turkish coal (a bituminous and a brown coal) were extracted with NMP-CS2 (1:1 v/v) and NMP-EDA (1:17, v/v) at room conditions and with NMP and NMP/EDA under reflux. To obtain any effect of solvent swelling on extraction yield coals were also extracted at same conditions after swelling with NMP and EDA. The extraction yield was maximum in the NMP-CS2 mixed solvent for higher ranked coal, suggesting a synergistic effect of the system. It was possible to extract over 35 % of sub-bituminous coal by using NMP- CS2. The extraction of same coal with NMP under reflux gave an extraction yield of 33% suggesting the useful effect of solvent swelling and heat during the reflux period. A positive effect of pre-swelling with NMP and EDA on extraction yield and recovery of solid extracts were observed , especially for brown coal sample. Following the extraction, solid extracts were produced with less than 0.12 % in ash content for almost all extraction conditions.

A novel concept for high conversion of coal to liquids. Final report, 1 September 1988--31 August 1992

Energy Technology Data Exchange (ETDEWEB)

Wiser, W.H.; Shabtai, J.

1994-04-01

A batch microreactor was designed and fabricated as a means of investigating maximum yields of liquids obtainable in very short reaction times of the order of a few seconds, and the maximum ratios of liquids/hydrocarbon (HC) gases obtainable under those conditions. A Wyodak sub-bituminous coal, crushed and sieved to {minus}200 mesh particle size, was used in the experiments, with a temperature of 500{degrees}C and a pressure of 1500 psi. The fine coal particles were fed dry to the reactor and heated to reaction temperature in times of one to two seconds. At a time of 3 seconds at reaction temperature, in a single pass a liquid yield of 60% by weight of the coal was obtained, accompanied by a ratio of liquids/(HC) gases of 30/1. When the unreacted solids were recycled to the reactor, and the results combined with those of the first pass, a liquid yield of 82% by weight of the coal was achieved, accompanied by a ratio of liquids/HC gases of 30/1. This ratio represents only about 3 wt percent HC gases, much lower that is produced in current advanced technologies, and represents a large saving in hydrogen consumption. A simulated distillation technique was applied to the liquids. The liquid product contained 86% by weight (of the liquids) total distillables (boiling point below 538{degrees}C), including 70% by weight of low-boiling fractions in the gasoline, kerosene and gas oil range (boiling point up to 325{degrees}C). The liquid product exhibited a H/C ratio of 1.5, which is considerably higher than observed in current advanced technologies for the primary liquids. Several catalysts were investigated. Iron catalysts, specifically ferric chloride hexahydrate and ferric sulfate pentahydrate, each produced these high conversions and high ratios of liquids/HC gases.

SYSTEM ANALYSIS OF NUCLEAR-ASSISTED SYNGAS PRODUCTION FROM COAL

International Nuclear Information System (INIS)

E. A. Harvego; M. G. McKellar; J. E. O'Brien

2008-01-01

A system analysis has been performed to assess the efficiency and carbon utilization of a nuclear-assisted coal gasification process. The nuclear reactor is a high-temperature helium-cooled reactor that is used primarily to provide power for hydrogen production via high-temperature electrolysis. The supplemental hydrogen is mixed with the outlet stream from an oxygen-blown coal gasifier to produce a hydrogen-rich gas mixture, allowing most of the carbon dioxide to be converted into carbon monoxide, with enough excess hydrogen to produce a syngas product stream with a hydrogen/carbon monoxide molar ratio of about 2:1. Oxygen for the gasifier is also provided by the high-temperature electrolysis process. Results of the analysis predict 90.5% carbon utilization with a syngas production efficiency (defined as the ratio of the heating value of the produced syngas to the sum of the heating value of the coal plus the high-temperature reactor heat input) of 66.1% at a gasifier temperature of 1866 K for the high-moisture-content lignite coal considered. Usage of lower moisture coals such as bituminous can yield carbon utilization approaching 100% and 70% syngas production efficiency

System Analysis of Nuclear-Assisted Syngas Production from Coal

International Nuclear Information System (INIS)

Harvego, E.A.; McKellar, M.G.; O'Brien, J.E.

2009-01-01

A system analysis has been performed to assess the efficiency and carbon utilization of a nuclear-assisted coal gasification process. The nuclear reactor is a high-temperature helium-cooled reactor that is used primarily to provide power for hydrogen production via high temperature electrolysis. The supplemental hydrogen is mixed with the outlet stream from an oxygen-blown coal gasifier to produce a hydrogen-rich gas mixture, allowing most of the carbon dioxide to be converted into carbon monoxide, with enough excess hydrogen to produce a syngas product stream with a hydrogen/carbon monoxide molar ratio of about 2:1. Oxygen for the gasifier is also provided by the high-temperature electrolysis process. Results of the analysis predict 90.5% carbon utilization with a syngas production efficiency (defined as the ratio of the heating value of the produced syngas to the sum of the heating value of the coal plus the high-temperature reactor heat input) of 64.4% at a gasifier temperature of 1866 K for the high-moisture-content lignite coal considered. Usage of lower moisture coals such as bituminous can yield carbon utilization approaching 100% and 70% syngas production efficiency.

Characteristics of carbonized sludge for co-combustion in pulverized coal power plants.

Science.gov (United States)

Park, Sang-Woo; Jang, Cheol-Hyeon

2011-03-01

Co-combustion of sewage sludge can destabilize its combustion profile due to high volatility, which results in unstable flame. We carried out fuel reforming for sewage sludge by way of carbonization at pyrolysis temperature of 300-500°C. Fuel characteristics of carbonized sludge at each temperature were analyzed. As carbonization temperature increased, fuel ratio increased, volatile content reduced, and atomic ratio relation of H/C and O/C was similar to that of lignite. The analysis result of FT-IR showed the decrease of aliphatic C-H bond and O-C bond in carbonization. In the analysis result of TG-DTG, the thermogravimetry reduction temperature of carbonized sludge (CS400) was proven to be higher than that of dried sludge, but lower than that of sub-bituminous coal. Hardgrove grindability index increased in proportion to fuel ratio increase, where the carbonized sludge value of 43-110 was similar or higher than the coal value of 49-63. As for ash deposits, slagging and fouling index were higher than that of coal. When carbonized sludge (CS400) and coal were co-combusted in 1-10% according to calorific value, slagging tendency was low in all conditions, and fouling tendency was medium or high according to the compositions of coal. Copyright © 2010 Elsevier Ltd. All rights reserved.

Kinetics of coal combustion: Part 3, Mechanisms and kinetics of char combustion

Energy Technology Data Exchange (ETDEWEB)

Gavalas, G. R.; Flagan, R. C. [California Inst. of Tech., Pasadena, CA (USA)

1988-09-01

This report summarizes a three-year research program aimed at developing this level of understanding of char combustion through a combination of detailed analysis of chars as produced during devolatilization and as they evolve during oxidation, and theoretical studies of the porous microstructures and of pore diffusion and reaction within the coal particles. A small number of coals have been studied in detail, namely a HVA bituminous (PSOC 1451), a sub-bituminous (PSOC 1488), and a lignite (PSOC 1443). Chars have been generated from size-classified samples of these coals by pyrolysis in an inert atmosphere in a drop tube furnace. The chars were then characterized both chemically and physically. Subsequent oxidation studies were performed on these chars. 42 refs., 54 figs., 4 tabs.

Potential for Coal-to-Liquids Conversion in the U.S.-Resource Base

International Nuclear Information System (INIS)

Croft, Gregory D.; Patzek, Tad W.

2009-01-01

By applying the multi-Hubbert curve analysis to coal production in the United States, we demonstrate that anthracite production can be modeled with a single Hubbert curve that extends to the practical end of commercial production of this highest-rank coal. The production of bituminous coal from existing mines is about 80% complete and can be carried out at the current rate for the next 20 years. The production of subbituminous coal from existing mines can be carried out at the current rate for 40-45 years. Significant new investment to extend the existing mines and build new ones would have to commence in 2009 to sustain the current rate of coal production, 1 billion tons per year, in 2029. In view of the existing data, we conclude that there is no spare coal production capacity of the size required for massive coal conversion to liquid transportation fuels. Our analysis is independent of other factors that will prevent large-scale coal liquefaction projects: the inefficiency of the process and either emissions of greenhouse gases or energy cost of sequestration

Biosolubilization gamma irradiate ion result coal by mould trichoderma sp

International Nuclear Information System (INIS)

Pingkan Aditiawati; Dea Indriani Astuti; Irawan Sugoro; Dwiwahju Sasongko

2011-01-01

Biosolubilization of coal is process of converting solid coal to liquid fuel/chemicals by mean of microorganism. The aim of this research was to study the effect of gamma rays irradiation with varian doses of irradiation into solubilization of subbituminous coal by Trichoderma sp. The dosage used was 5, 10, and 20 kGy and unirradiated coal as control. The method was submerged culture in MSS+ medium and incubated at room temperature and agitated at 150 rpm for 21 th days. The parameters observed were colonization, pH and biosolubilization product based on absorbance value at λ 250nm and λ 450nm and GC/MS analysis for the best treatment. The results showed that coal biosolubilization could be increased by gamma irradiation. The mould could growth well in medium containing irradiated coal and the medium of pH was decreased after incubation. The biosolubilization was increased but the irradiation dosage of coal didn't affect significantly. The best dose was 20 kGy with product biosolubilization similar to gasoline and solar. Based on the result, the pre-treatment of gamma irradiation on coal has potency to increased biosolubilization. (author)

Petrographic properties of major coal seams in Turkey and their formation

Energy Technology Data Exchange (ETDEWEB)

Toprak, Selami [Mineral Research and Exploration Directorate (MTA), 06520 Ankara (Turkey)

2009-06-01

Most types of coal in Turkey are generally low in rank: lignite, and subbituminous. Most of the coal was formed during the Miocene, Eocene, and Pliocene ages. There are only a few thin Jurassic-age coal occurrences in Turkey. Pennsylvanian age bituminous coal is found on the Black Sea coast. General implications of the petrographic properties of Turkey's coal seams and coal deposits have not yet been taken into consideration comparatively or as a whole. For this study, about 190 channel samples were collected from different locales. The composite profile samples of the seams were taken into considerations. The content and depositional properties as well as some chemical and physical properties of the main coal seams are compared. All coal samples tend to have similar coal petrographic properties and were deposited in intermontane lacustrine basins. Later, they were affected by faulting and post-depositional volcanic activity. As a result, there are variations in the properties and rank of the coal samples. The most abundant coal maceral group is huminite and the most abundant maceral is gelinite. The liptinite and inertinite contents of the coal are low and the maceral contents of the coals show great similarity. The depositional environments of the all coals are lacustrine dominated. (author)

Quality and petrographic characteristics of the lacustrine Ermenek coal (early Miocene), Turkey

Energy Technology Data Exchange (ETDEWEB)

Demirel, I.H.; Karayigit, A.I. [Hacettepe Univ., Beytepe-Ankara (Turkey). Dept. of Geological Engineering

1999-05-01

The early Miocene Yenimahalle Formation including alluvial-lacustrine sediments and a mineable coal steam with an average of 5 m in thickness rests unconformably upon the basement and is also unconformably overlain by marine limestones of the middle-late Miocene Mut Formation in the Ermenek coal basin. The coal basin in the present study has been subdivided into two areas, Canakci and Pamuklu-Tepebasi, which are separated by the basement and a fault, in order to determine coal properties in detail. The investigated subbituminous coals with an average of 0.40%Ro huminite reflectance often contain gastropod shells (Planorbidae) which commonly maintain the original aragonite and calcite composition. The coals have similar chemical properties and petrographic composition in the two areas, but their sulphur contents are clearly different. In the Canakci area the coals on an air-dried basis contain distinctly less total sulphur (avg. 1.3%) and organic sulphur contents (0.13--0.15%) than in the Pamuklu-Tepebasi area (avg. 4.5% and 4.25%, respectively). This difference is interpreted to be controlled by mire chemistry and sedimentation during peat formation.

Genetic-industrial classification of brown coals in Serbia

Energy Technology Data Exchange (ETDEWEB)

Ercegovac, Marko [Serbian Academy of Sciences and Arts, Knez Mihailova 35, 11000 Belgrade (Serbia and Montenegro); ?ivotic, Dragana; Kostic, Aleksandar [University of Belgrade, Faculty of Mining and Geology, Djusina 7, 11000 Belgrade (Serbia and Montenegro)

2006-08-01

The petrologic, chemical and technological features of low-rank coals from nineteen of the most important basins in Serbia have been studied as part of the research project of genetic-industrial classification of low-rank coals of Serbia. Most of these features have been included as parameters of the codification system for low-rank coals. The paper discusses the main genetic, technological and supplementary parameters of the Serbian brown coals such as rank, petrographic composition, gelification degree, total moisture, ash content, sulphur content, calorific value, tar yield, the chemical composition and the thermotechnical properties of ash. The rank of brown coals from Serbia has been defined on the basis of the following parameters: random reflectance of huminite/vitrinite (R{sub r}=0.26-0.50%), total moisture (W{sup ar}=13.18-49.11%), gross calorific value (Q{sup daf}=22.3-29.2MJ/kg, dry, ash-free basis), net calorific value (Q{sup daf}=21.2-28.1MJ/kg, dry, ash-free basis). The results from the maceral analysis confirm that the humic coals, in general, are characterized by high huminite content (76.0-97.9vol.%, mineral matter free), low inertinite amount (0.7-6.3vol.%, mineral matter free), and a variable amount of liptinite (0.8-15.5vol.%, mineral matter free). It is possible to define three groups of Serbian brown coals on the basis of the primary, or genetic parameters, technological, or chemical parameters, and supplementary parameters: soft (Low-Rank C; [Economic Commission for Europe, Committee on Sustainable Energy- United Nations (ECE-UN), 1998. International Classification of in-Seam Coals. Energy 19, 41 pp.; Economic Commission for Europe, Committee on Sustainable Energy- United Nations (ECE-UN), 1999. International Codification System for Low-Rank Coals. Energy 9, 19 pp.; Economic Commission for Europe, Committee on Sustainable Energy- United Nations (ECE-UN), 2000. International Classification for Low-Rank Coals. Energy 12, 21 pp.]), dull (Low

FY 2000 survey of the geological structure overseas, etc. Japan-China joint coal exploration - Yu Xian project; 2000 nendo kaigai chishitsu kozo nado chosa - futai shiryoshu. Nippon Chugoku sekitan kyodo tansa Yu Xian project

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This data book summarized the proceedings and the technical report of the management committee on the Japan-China geological structure survey based on the consultation concluded between NEDO and China's bureau of coal field geology and a report meeting on the Yu Xian project. In the exploration, conducted were the boring survey of 10 boreholes, seismic survey of 2D (71 traverse lines, 180.105km) and 3D (1.5km{sup 2}), VSP (6 holes (345 shots)) and the low velocity band survey (2,072 shots). The geological structure of the area presented the syncline structure with a gentle line associated with foldings and a number of faults and was classified into the medium class or the class of a little complication in the Chinese standard. The number of the faults confirmed in this exploration totaled 57. Coal reserves by coal seam were 157.22 million tons at No. 5 seam and 102.57 million tons at No. 1 seam. The total amount of the two seams was 79.1% of the total coal amount in all area. The coal quality of Nos. 1 and 5 was brown coal - flame coal in the Chinese classification, and subbituminous coal B - subbituminous coal C in the ASTM classification. The coal, however, cannot be used for process raw coal. There is a technical potentiality of the fixed bed pressurized gasification. (NEDO)

Examination of flame length for burning pulverized coal in laminar flow reactor

Energy Technology Data Exchange (ETDEWEB)

Kim, Jae Dong; Kim, Gyu Bo; Chang, Young June; Song, Ju Hun; Jeon, Chung Hwan [Pusan National University, Busan (Korea, Republic of)

2010-12-15

Because there has been a recent increase in the use of low calorific coal compared to standard coal, it is crucial to control the char flame length governing the burning life-time of coal in a coal-fired utility boiler. The main objective of this study is to develop a simplified model that can theoretically predict the flame length for burning coal in a laboratory-scale entrained laminar flow reactor (LFR) system. The char burning behavior was experimentally observed when sub-bituminous pulverized coal was fed into the LFR under burning conditions similar to those in a real boiler: a heating rate of 1000 K/s, an oxygen molar fraction of 7.7 %, and reacting flue gas temperatures ranging from 1500 to 2000 K. By using the theoretical model developed in this study, the effect of particle size on the coal flame length was exclusively addressed. In this model, the effect of particle mass was eliminated to compare with the experimental result performed under a constant mass feeding of coal. Overall, the computed results for the coal flame length were in good agreement with the experimental data, particularly when the external oxygen diffusion effect was considered in the model

Examination of flame length for burning pulverized coal in laminar flow reactor

International Nuclear Information System (INIS)

Kim, Jae Dong; Kim, Gyu Bo; Chang, Young June; Song, Ju Hun; Jeon, Chung Hwan

2010-01-01

Because there has been a recent increase in the use of low calorific coal compared to standard coal, it is crucial to control the char flame length governing the burning life-time of coal in a coal-fired utility boiler. The main objective of this study is to develop a simplified model that can theoretically predict the flame length for burning coal in a laboratory-scale entrained laminar flow reactor (LFR) system. The char burning behavior was experimentally observed when sub-bituminous pulverized coal was fed into the LFR under burning conditions similar to those in a real boiler: a heating rate of 1000 K/s, an oxygen molar fraction of 7.7 %, and reacting flue gas temperatures ranging from 1500 to 2000 K. By using the theoretical model developed in this study, the effect of particle size on the coal flame length was exclusively addressed. In this model, the effect of particle mass was eliminated to compare with the experimental result performed under a constant mass feeding of coal. Overall, the computed results for the coal flame length were in good agreement with the experimental data, particularly when the external oxygen diffusion effect was considered in the model

The production of activated carbon from nigerian mineral coal via steam activation

International Nuclear Information System (INIS)

Nwosu, F.O.; Owolabi, B.I.O.; Adebowale, O.

2010-01-01

Activated carbon was produced from Okpara sub-bituminous coal and Ogwashi brown lignite coal of Nigeria through steam activation at 900 degree C and 960 degree C each for 30 min and 60 min. Okpara and Ogwashi precursor coals had carbon content of 67.41 and 64.47%, respectively, whereas the bulk density and the ash content were 0.59 - 0.68 g/mL and 2.56-9.91%, respectively. The former exhibited up to 901.0 mg/g iodine number and Brunauer Emmett Teller (BET) surface area of 604 m/sup 2/g while the latter, iodine number of 998.0 mg/g and 669 m/sup 2/g BET surface area. Both showed adequate porosity indicative of their potential for utilization for commercial production of active carbons. (author)

Coal Direct Chemical Looping Retrofit to Pulverized Coal Power Plants for In-Situ CO2 Capture

Energy Technology Data Exchange (ETDEWEB)

Zeng, Liang; Li, Fanxing; Kim, Ray; Bayham, Samuel; McGiveron, Omar; Tong, Andrew; Connell, Daniel; Luo, Siwei; Sridhar, Deepak; Wang, Fei; Sun, Zhenchao; Fan, Liang-Shih

2013-09-30

A novel Coal Direct Chemical Looping (CDCL) system is proposed to effectively capture CO2 from existing PC power plants. The work during the past three years has led to an oxygen carrier particle with satisfactory performance. Moreover, successful laboratory, bench scale, and integrated demonstrations have been performed. The proposed project further advanced the novel CDCL technology to sub-pilot scale (25 kWth). To be more specific, the following objectives attained in the proposed project are: 1. to further improve the oxygen carrying capacity as well as the sulfur/ash tolerance of the current (working) particle; 2. to demonstrate continuous CDCL operations in an integrated mode with > 99% coal (bituminous, subbituminous, and lignite) conversion as well as the production of high temperature exhaust gas stream that is suitable for steam generation in existing PC boilers; 3. to identify, via demonstrations, the fate of sulfur and NOx; 4. to conduct thorough techno-economic analysis that validates the technical and economical attractiveness of the CDCL system. The objectives outlined above were achieved through collaborative efforts among all the participants. CONSOL Energy Inc. performed the techno-economic analysis of the CDCL process. Shell/CRI was able to perform feasibility and economic studies on the large scale particle synthesis and provide composite particles for the sub-pilot scale testing. The experience of B&W (with boilers) and Air Products (with handling gases) assisted the retrofit system design as well as the demonstration unit operations. The experience gained from the sub-pilot scale demonstration of the Syngas Chemical Looping (SCL) process at OSU was able to ensure the successful handling of the solids. Phase 1 focused on studies to improve the current particle to better suit the CDCL operations. The optimum operating conditions for the reducer reactor such as the temperature, char gasification enhancer type, and flow rate were identified. The

Development of zero conditioning procedure for coal reverse flotation

Energy Technology Data Exchange (ETDEWEB)

D.P. Patil; J.S. Laskowski [University of British Columbia, Vancouver, BC (Canada). Mining Engineering Department

2008-04-15

The zero conditioning method was developed to facilitate the flotation of gangue minerals in the reverse coal flotation process. Batch and continuous methods were developed to maintain the zero conditioning principle during reverse flotation. Batch zero conditioning was achieved by adding the required amount of DTAB in one step, as soon as the air was introduced into the system. The continuous zero conditioning method involves uninterrupted addition of DTAB through a specially built sparger in the form of aerosol during the flotation experiment. This produces active bubbles that carry collector. The addition of DTAB in the form of aerosol during reverse flotation proved to be better in reducing the ash of a sub-bituminous (LS-26) coal from 34.7% to 22.9% with a froth product (gangue) yield of 36.8% without any depressant. In the presence of coal depressant (dextrin, 0.5 kg/t), the ash content of LS-26 coal was reduced from 34.7% to 16.5% at a clean coal yield of 55%, whereas the conventional (forward) flotation with fuel oil provided a clean coal containing 16.5% ash with only 29.2% yield. These results prove that flotation of gangue minerals is very much improved by maintaining zero conditioning time conditions in a coal reverse flotation process.

Carbon dioxide emission factors for U.S. coal by origin and destination

Science.gov (United States)

Quick, J.C.

2010-01-01

This paper describes a method that uses published data to calculate locally robust CO2 emission factors for U.S. coal. The method is demonstrated by calculating CO2 emission factors by coal origin (223 counties, in 1999) and destination (479 power plants, in 2005). Locally robust CO2 emission factors should improve the accuracy and verification of greenhouse gas emission measurements from individual coal-fired power plants. Based largely on the county origin, average emission factors for U.S. lignite, subbituminous, bituminous, and anthracite coal produced during 1999 were 92.97,91.97,88.20, and 98.91 kg CO2/GJgross, respectively. However, greater variation is observed within these rank classes than between them, which limits the reliability of CO2 emission factors specified by coal rank. Emission factors calculated by destination (power plant) showed greater variation than those listed in the Emissions & Generation Resource Integrated Database (eGRID), which exhibit an unlikely uniformity that is inconsistent with the natural variation of CO2 emission factors for U.S. coal. ?? 2010 American Chemical Society.

Paleocene coal deposits of the Wilcox group, central Texas

Science.gov (United States)

Hook, Robert W.; Warwick, Peter D.; SanFilipo, John R.; Schultz, Adam C.; Nichols, Douglas J.; Swanson, Sharon M.; Warwick, Peter D.; Karlsen, Alexander K.; Merrill, Matthew D.; Valentine, Brett J.

2011-01-01

Coal deposits in the Wilcox Group of central Texas have been regarded as the richest coal resources in the Gulf Coastal Plain. Although minable coal beds appear to be less numerous and generally higher in sulfur content (1 percent average, as-received basis; table 1) than Wilcox coal deposits in the Northeast Texas and Louisiana Sabine assessment areas (0.5 and 0.6 percent sulfur, respectively; table 1), net coal thickness in coal zones in central Texas is up to 32 ft thick and more persistent along strike (up to 15 mi) at or near the surface than coals of any other Gulf Coast assessment area. The rank of the coal beds in central Texas is generally lignite (table 1), but some coal ranks as great as subbituminous C have been reported (Mukhopadhyay, 1989). The outcrop of the Wilcox Group in central Texas strikes northeast, extends for approximately 140 mi between the Trinity and Colorado Rivers, and covers parts of Bastrop, Falls, Freestone, Lee, Leon, Limestone, Milam, Navarro, Robertson, and Williamson Counties (Figure 1). Three formations, in ascending order, the Hooper, Simsboro, and Calvert Bluff, are recognized in central Texas (Figure 2). The Wilcox Group is underlain conformably by the Midway Group, a mudstone-dominated marine sequence, and is overlain and scoured locally by the Carrizo Sand, a fluvial unit at the base of the Claiborne Group.

Formation of N{sub 2} during the fixed-bed pyrolysis of coals

Energy Technology Data Exchange (ETDEWEB)

Wu, Zhiheng; Ohtsuka, Yasuo [Tohoku Univ., Sendai (Japan); Furimsky, E. [Natural Resources Canada, Ottawa, Ontario (Canada)

1995-12-31

Research on the fate of the nitrogen in coal during pyrolysis has attracted increased attention, since it is related with the NO{sub x} and N{sub 2}O emissions during subsequent combustion. It has been reported that coal nitrogen is initially released as tar, which is then converted to HCN and NH{sub 3} through secondary decomposition reactions. However, little attention to N{sub 2} has been paid so far. We have recently found that N{sub 2} is the dominant product in slow heating rate pyrolysis of a subbituminous coal, and that the finely dispersed iron catalyst promotes drastically the formation of N{sub 2} from a brown coal. If coal nitrogen can be removed efficiently as N{sub 2} during pyrolysis, this method would contribute to the reduction of the NO{sub x} and N{sub 2}O emissions, since such pollutants originate mostly from coal nitrogen. Therefore the present study aims at making clear the influence of coal type, pyrolysis conditions, demineralization, and iron catalyst on the formation of N{sub 2} during the fix-bed pyrolysis of several coals with different ranks.

CFD study of temperature distribution in full scale boiler adopting in-furnace coal blending

International Nuclear Information System (INIS)

Fadhil, S S A; Hasini, H; Shuaib, N H

2013-01-01

This paper describes the investigation of temperature characteristics of an in-furnace combustion using different coals in a 700 MW full scale boiler. Single mixture fraction approach is adopted for combustion model of both primary and secondary coals. The primary coal was based on the properties of Adaro which has been used as the design coal for the boiler under investigation. The secondary blend coal was selected based on sub-bituminous coal with higher calorific value. Both coals are simultaneously injected into the furnace at alternate coal burner elevations. The general prediction of the temperature contours at primary combustion zone shows identical pattern compared with conventional single coal combustion in similar furnace. Reasonable agreement was achieved by the prediction of the average temperature at furnace exit. The temperature distribution is at different furnace elevation is non-uniform with higher temperature predicted at circumferential 'ring-like' region at lower burner levels for both cases. The maximum flame temperature is higher at the elevation where coal of higher calorific value is injected. The temperature magnitude is within the accepTable limit and the variations does not differ much compared to the conventional single coal combustion.

Secondary biogenic coal seam gas reservoirs in New Zealand: A preliminary assessment of gas contents

Energy Technology Data Exchange (ETDEWEB)

Butland, Carol I. [Department of Geological Sciences, University of Canterbury, Private Bag 4800, Christchurch (New Zealand); Moore, Tim A. [Department of Geological Sciences, University of Canterbury, Private Bag 4800, Christchurch (New Zealand); Solid Energy NZ Ltd., P.O. Box 1303, Christchurch (New Zealand)

2008-10-02

Four coal cores, one from the Huntly (Eocene), two from the Ohai (Cretaceous) and one from the Greymouth (Cretaceous) coalfields, were sampled and analysed in terms of gas content and coal properties. The coals vary in rank from subbituminous B-A (Huntly) to subbituminous C-A (Ohai), and high volatile A bituminous (Greymouth). Average gas contents were 1.60 m{sup 3}/t (s 0.2) in the Huntly core, 4.80 m{sup 3}/t (s = 0.8) in the Ohai cores, and 2.39 m{sup 3}/t (s = 0.8) in the Greymouth core. The Ohai core not only contained more gas but also had the highest saturation (75%) compared with the Huntly (33%) and Greymouth (45%) cores. Carbon isotopes indicate that the Ohai gas is more mature, containing higher {delta}{sup 13}C isotopes values than either the Huntly or Greymouth gas samples. This may indicate that the gas was derived from a mixed biogenic and thermogenic source. The Huntly and Greymouth gases appear to be derived solely from a secondary biogenic (by CO{sub 2} reduction) source. Although the data set is limited, preliminary analysis indicates that ash yield is the dominant control on gas volume in all samples where the ash yield was above 10%. Below 10%, the amount of gas variation is unrelated to ash yield. Although organic content has some influence on gas volume, associations are basin and/or rank dependent. In the Huntly core total gas content and structured vitrinite increase together. Although this relationship does not appear for the other core data for the Ohai SC3 core, lost gas and fusinite are associated whereas gelovitrinite (unstructured vitrinite) correlates positively with residual gas for the Greymouth data. (author)

Infrared absorption characteristics of hydroxyl groups in coal tars

Energy Technology Data Exchange (ETDEWEB)

Cannon, S A; Chu, C J; Hange, R H; Margrave, J L

1987-01-01

Tar evolution was observed over a temperature range of 150-600 C for four coals. Pittsburgh bituminous, Illinois No.6, Rawhide subbituminous, and Texas lignite. Isolation of the evolved tars in a nitrogen matrix at 15 degrees K produced better resolved infrared spectra than those in a coal matrix, thus enhancing structural characterization of the tar molecules. Two distinct hydroxyl functional groups in the tar molecules free of hydrogen bonding were identified for the first time without interference from H/sub 2/O absorptions. These absorptions at 3626.5 cm/sup -1/ have been assigned to phenolic hydroxyls. It is suggested that carboxylic and aliphatic hydroxyl groups do not survive the vaporization process. Tars from Illinois No.6 were found to contain the largest amount of phenolic hydroxyl; Pittsburgh No. 8 tar contains approximately half of that for Illinois No.6 while Rawhide and Texas lignite contain much less phenolic than either of the other coals. 10 references, 6 figures, 1 table.

Parameters influencing the variation in mercury emissions from an Alberta power plant burning high inertinite coal over thirty-eight weeks period

Energy Technology Data Exchange (ETDEWEB)

Goodarzi, F.; Reyes, J. [Environmental Studies, Geological Survey of Canada-Calgary, 3303-33rd Street N.W., Calgary, Alberta (Canada T2L 2A7); Schulz, J.; Hollman, D. [EPCOR 10065 Jasper Ave Edmonton, Alberta (Canada T5J 3B1); Rose, D. [Air Pollution Prevention Directorate Environment Canada, 315 St-Joseph Blvd Hull, Quebec (Canada K1A 0H3)

2006-01-03

Feed coals and fly ashes from a coal-fired power station burning Alberta subbituminous coal were examined for a period of thirty-eight weeks to determine the variation in emitted mercury. Feed coal samples were analyzed for proximate, calorific value and Hg content, while fly ash samples were examined for C and Hg contents. The maceral content of the feed coal was also determined. The emitted mercury was calculated and compared to mercury emitted from the stack according to a mass-balance calculation from a previous study for the same station. Mercury contents ranged from 0.029 to 0.066 mg/kg for feed coal, and from 0.069 to 0.112 mg/kg for fly ash. The carbon/char in fly ash was separated into reactive (vitrinitic/bimacerate) and less reactive (inertinitic) chars using ZnBr{sub 2} at specific gravities of 1.7, 2.0, and 2.25 to 2.4. The result shows that there is a positive correlation between the carbon and mercury content of the fly ash. The reactive char particles in the fly ash may be responsible for the capture mercury in fly ash. The percentage of estimated captured mercury by fly ash increases with increasing carbon content (%) in fly ash. The percentage of emitted mercury for the period of 38 weeks is estimated to be within the range of 49% to 76% of the total input of mercury. (author)

Quality and petrographic characteristics of the Lacustrine Ermenek Coal (Early Miocene), Turkey

Energy Technology Data Exchange (ETDEWEB)

Demirel, I.H.; Karayigit, A.I.

1999-04-15

The early Miocene Yenimahalle Formation including alluvial-lacustrine sediments and a mineable coal seam with an average of 5 m in thickness rests unconformably upon the basement and is also unconformably overlain by marine limestones of the middle-late Miocene Mut Formation in the Ermenek coal basin. The coal basin in the present study has been subdivided into two areas, Canakci and Pamuklu-Tepebasi, which are separated by the basement and a fault, in order to determine coal properties in detail. The investigated subbituminous coals with an average of 0.40% Ro huminite reflectance often contain gastropod shells (Planorbidae) which commonly maintain the original aragonite and calcite composition. The coals have similar chemical properties and petrographic composition in the two areas, but their sulphur contents are clearly different. In the Canakci area the coals on an air-dried basis contain distinctly less total sulphur (avg. 1.3%) and organic sulphur contents (0.13 0.15%) than in the Pamuklu-Tepebasi area (avg. 4.5% and 4.25%, respectively). This difference is interpreted to be controlled by mire chemistry and sedimentation during peat formation. (author)

Coal waste slurries as a fuel for integrated gasification combined cycle plants

Directory of Open Access Journals (Sweden)

Lutynski Marcin A.

2016-01-01

Full Text Available The article summarizes recent development in integrated gasification combined cycle technology and lists existing and planned IGCC plants. A brief outlook on the IGCC gasification technology is given with focus on entrained-flow gasifiers where the low-quality coal waste slurry fuel can be used. Desired properties of coal and ash for entrained-flow gasifiers are listed. The coal waste slurries, which were deposited at impoundments in Upper Silesian Coal Basin, were considered as a direct feed for such gasifiers. The average ash content, moisture content and lower heating value were analysed and presented as an average values. Entrained-flow commercial gasifiers can be considered as suitable for the coal slurry feed, however the ash content of coal slurries deposited in impoundments is too high for the direct use as the feed for the gasifiers. The moisture content of slurries calculated on as received basis meets the requirements of entrained-flow slurry feed gasifiers. The content of fines is relatively high which allow to use the slurries in entrained-flow gasifiers.

Atlas of the Colombian coal, Potential map and rank: Map 5-09

International Nuclear Information System (INIS)

Pulido Gonzalez, Orlando

1999-01-01

With the presentation of the Atlas of Coal to scale 1:500.000, it is sought to show to big features the location of the different areas with coal in Colombia, associating with the geologic units, the potential and the range. In the Map 5-09, the formations that include the coal are defined as Umir, Guaduas, Limbo, (Los Cuervos), San Fernando, (Carbonera), defined as Kst, Ksgt and Pgt. For the potential an arbitrary scale settled down, in the following way: in the first place bigger to 1000 million tons; between 1000 and 100; between 100 and 10 and lastly smaller to 10 million tons. These figures are represented in the map by triangles with colors that they are equal before to the figures mentioned. Keeping in mind the scale, it was opted to report the potential in the category of the hypothetical resources; when the resources or reserves are established, they are also reported. As for the range, in the map it is indicated by means of symbols that should be taken as a domain or tendency of the coal in each area in general. The the coal rank understood as the transformation that has reached along the geologic evolution is what is mentioned as anthracitic coal, semi-anthracitic, bituminous low in volatile, bituminous middle in volatile, bituminous high in volatile A, B and C, sub-bituminous and lastly the lignite. For each map are mentioned that there are determined

Application of nuclear techniques for analysis of Vietnamese coal and embedding rocks

International Nuclear Information System (INIS)

Vo Dac Bang; Pham Van Duong; Nguyen Thanh Binh; Le Tien Quan; Nguyen Manh Hung; Nguyen Thi Hong; Vu Hoang Lam

1995-01-01

In the paper the result of elemental analysis by Nuclear Techniques of Coal and Embedded rocks samples from Vietnamese Quang Ninh and Thai Nguyen basins were presented. Methods used were: Neutron activation Analysis at Dalat Reactor, low counting with HP-Ge and NaJ detectors and X-ray fluorescent analysis with planar Si (Si) detector. Mean concentrations of 19 elements in coal and 9 in rocks were determined. Correlation between concentrations of elements were found. It appears that the correlation between ash content and U, K, Th, concentrations was poor for Quang Ninh antracitecoal. Correlation coefficient was found to be 0,63 for ash range 0-40%. Content of Th in anthracite Quang Ninh coal was much higher than reported in literature for subbituminous, bituminous and lignite coals, while Thai Nguyen fat coal contains considerable amount of Cu, Pb, Zn. Obtained data were useful for evaluation of potential hazard for environment from using coal as fuel for coal fired power plants, for estimation of possibility of using nuclear technique in coal industry in Vietnam. They could be used also for geochemical investigations. The simple of-line coal ash gauge basing on attenuation of soft gamma radiation from Fe-55 was also described. (author). 6 refs, 3 figs, 8 tabs

Pyrolisator Coal to be Cokes (Coal Cokes Casting Metal Industry Standard

Directory of Open Access Journals (Sweden)

Sukamto

2016-01-01

Full Text Available Pyrolisis of coal is partial combustion to reduce total moisture, volatile matter and sulfur contens and increase the calorific value of coal. The results of pyrolysis of coal is coke. At the laboratory level studies, pyrolisis done in batch using different calorie, namely 5800, 6000, 6300 kcal/kg and a time of 15-60 minutes and the temperature 400-800°C. Maximum results obtained total moisture (0.44%, fixed carbon (89%, volatile matter (2.4%, sulfur content (undetected and ash (7.2%. Then applied to the scale miniplant with continuous processes using multitube pyrolisator which are designed to operate in the temperature range 400-800°C and a flow rate of 240-730 kg/h, obtained coal cokes that meets industry quality standards, namely TM (0.42%, FC (90.40%, VM (2.16%, S (not detected, Ash (6.8% incalori 6300 kcal/h, a flow rate of 240 kg / h and temperatures between 600-700°C

Co-gasification of pine and oak biochar with sub-bituminous coal in carbon dioxide.

Science.gov (United States)

Beagle, E; Wang, Y; Bell, D; Belmont, E

2018-03-01

Pine and oak biochars derived as byproducts of demonstration-scale pyrolysis, and blends of these two feedstocks with Powder River Basin coal, were gasified in a carbon dioxide environment using a modified drop tube reactor (MDTR) and a thermogravimetric analyzer (TGA). The impact of gasification temperature on conversion kinetics was evaluated from the temporal evolution of major product gases in the MDTR as measured using a mass spectrometer. Random pore modeling was conducted to simulate gasification in the MDTR with favorable results. The MDTR and TGA were used to conduct gasification for assessment of non-linear additive effects in the blends. Additive analysis of the blends showed deviation from the experimental blend results, indicating inhibiting effects of co-gasifying the biochar and coal. Inhibitory effects are more significant for oak than pine and more pronounced in the TGA at lower gasification temperatures. Results are discussed in the context of feedstock and reactor type. Copyright © 2017 Elsevier Ltd. All rights reserved.

Nuclear magnetic resonance studies of ancient buried wood-II. Observations on the origin of coal from lignite to bituminous coal

Science.gov (United States)

Hatcher, P.G.; Breger, I.A.; Szeverenyi, N.; Maciel, G.E.

1982-01-01

Coalified logs ranging in age from Late Pennsylvania to Miocene and in rank from lignite B to bituminous coal were analyzed by 13C nuclear magnetic resonance (NMR) utilizing the cross-polarization, magic-angle spinning technique, as well as by infrared spectroscopy. The results of this study indicate that at least three major stages of coalification can be observed as wood gradually undergoes transformation to bituminous coal. The first stage involves hydrolysis and loss of cellulose from wood with retention and differential concentration of the resistant lignin. The second stage involves conversion of the lignin residues directly to coalified wood of lignitic rank, during which the oxygen content of intermediate diagenetic products remains constant as the hydrogen content and the carbon content increases. These changes are thought to involve loss of methoxyl groups, water, and C3 side chains from the lignin. In the third major stage of coalification, the coalified wood increases in rank to subbituminous and bituminous coal; during this stage the oxygen content decreases, hydrogen remains constant, and the carbon content increases. These changes are thought to result from loss of soluble humic acids that are rich in oxygen and that are mobilized during compaction and dewatering. Relatively resistant resinous substances are differentially concentrated in the coal during this stage. The hypothesis that humic acids are formed as mobile by-products of the coalification of lignin and function only as vehicles for removal of oxygen represents a dramatic departure from commonly accepted views that they are relatively low-molecular-weight intermediates formed during the degradation of lignin that then condense to form high-molecular-weight coal structures. ?? 1982.

Achievement report for fiscal 1982 on Sunshine Program. Coal energy; 1982 nendo sunshine keikaku seika hokokusho. Sekitan energy

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-07-01

This research program consists of (1) the solid catalyst-aided reforming of various petroleum based oils and heavy coal oils into Solvolysis solvents and the secondary hydrogenolysis, (2) a search for pre-treatment for improvement on the sub-bituminous coal liquefaction yield, and (3) a search for measures for improvement on the brown coal liquefaction yield. Studied in this fiscal year are (1) the high-temperature short-contact time liquefaction of brown coal, (2) the role of catalyst support for selective upgrading of SRC (solvent refined coal), and (3) reforming of thermal melting feature of low rank coal by preliminary deashing at room temperature. In relation with Item (1), it is found that the dehydrogenation or reaction to carbonization of molecules involved in hydrogen donation is structure-sensitive but that thermolysis of coal is accelerated under high-temperature conditions to allow transfer hydrogen to contribute uniformly. It is deemed also that matching is excellent between hydrogen transfer and thermolysis, that the solvent dissolution level is elevated, and that the reaction short in duration inhibits consecutive polymerization reaction. These are supposed to be effective in improving on the liquefaction yield and in rendering heavy constituents lighter. In relation with Item (2), it is found that the experimentally manufactured catalysts are effective in reducing the weight of heavy constituents. In relation with Item (3), a carbonization reforming method is experimentally implemented in which the ash that affects carbonization is further removed by a pre-treatment at room temperature. (NEDO)

Conversion of Low-Rank Wyoming Coals into Gasoline by Direct Liquefaction

Energy Technology Data Exchange (ETDEWEB)

Polyakov, Oleg

2013-12-31

Under the cooperative agreement program of DOE and funding from Wyoming State’s Clean Coal Task Force, Western Research Institute and Thermosolv LLC studied the direct conversion of Wyoming coals and coal-lignin mixed feeds into liquid fuels in conditions highly relevant to practice. During the Phase I, catalytic direct liquefaction of sub-bituminous Wyoming coals was investigated. The process conditions and catalysts were identified that lead to a significant increase of desirable oil fraction in the products. The Phase II work focused on systematic study of solvothermal depolymerization (STD) and direct liquefaction (DCL) of carbonaceous feedstocks. The effect of the reaction conditions (the nature of solvent, solvent/lignin ratio, temperature, pressure, heating rate, and residence time) on STD was investigated. The effect of a number of various additives (including lignin, model lignin compounds, lignin-derivable chemicals, and inorganic radical initiators), solvents, and catalysts on DCL has been studied. Although a significant progress has been achieved in developing solvothermal depolymerization, the side reactions – formation of considerable amounts of char and gaseous products – as well as other drawbacks do not render aqueous media as the most appropriate choice for commercial implementation of STD for processing coals and lignins. The trends and effects discovered in DCL point at the specific features of liquefaction mechanism that are currently underutilized yet could be exploited to intensify the process. A judicious choice of catalysts, solvents, and additives might enable practical and economically efficient direct conversion of Wyoming coals into liquid fuels.

Thermal processing of Khoot coal and characterization of obtained solid and liquid products

Directory of Open Access Journals (Sweden)

S Batbileg

2014-12-01

Full Text Available On 21st January 2015, the abstract of this paper was replaced with the correct abstract.The coal of Khoot deposit have been investigated and determined the technical characteristics, elemental and petrographical maceral compositions. On the basis of proximate, ultimate, petrographic and IR analysis results have been confirmed that the Khoot coal is a sub-bituminous coal. The hard residue after pyrolysis have been activated by heated water steam and determined the iodine and methylene blue adsorption of initial coal and activated carbon samples from pyrolysis hard residue. The porosity structure of initial coal, activated carbon of pyrolysis hard residue and hard residue after thermolysis (thermal dissolution have been determined by SEM analysis. The liquid tar product of thermolysis of Khoot coal was investigated by FTIR, 13C and 1H NMR spectrometric analysis. The results of thermolysis of Khoot coal in tetralin with constant mass ratio between coal and tetralin (1:1.8 at 450°C show that 60.8% of liquid product can be obtained after thermolysis of the coal organic mass.DOI: http://doi.dx.org/10.5564/mjc.v15i0.326 Mongolian Journal of Chemistry 15 (41, 2014, p66-72

Effect of hydrothermal dewatering on the slurryability of brown coals

International Nuclear Information System (INIS)

Yu Yujie; Liu Jianzhong; Wang Ruikun; Zhou Junhu; Cen Kefa

2012-01-01

Highlights: ► Brown coals are upgraded by hydrothermal dewatering. ► The moisture content and oxygen functional groups decrease during the process. ► The point of zero charge and the contact angle rise as the temperature increases. ► The products were highly hydrophobic. ► The improvement on slurryability of solid products were examined. - Abstract: Two brown coals from China were dewatered under hydrothermal dewatering (HTD) conditions at 250–320 °C for 1 h in a 2 L autoclave. The hydrothermally dewatered products were used to prepare coal water slurry (CWS) with a lower viscosity than brown raw coal slurry. Moreover, the coal rank and heat value of the brown coal increased as the inherent moisture and oxygen content decreased during the HTD process. The maximum solid concentration of CWS prepared from XiMeng coal increased from 45.7% to 59.3%, whereas that of CWS prepared from BaoTou coal increased from 53.7% to 62.1%, after being dewatered at 320 °C. The improvement in the slurryability of brown coal significantly depended on the final temperature of the HTD process, the mechanism of which can be explained by the chemical analysis of oxygen functional groups, zeta potential, and the contact angle of the surface between coal and water. The oxygen functional groups, the oxygen/carbon ratio and hydrogen/carbon ratio in brown coal decreased, indicating that the coal rank was upgraded during the HTD process. As a result, both the point of zero charge and the contact angle increased, implying that the HTD products were highly hydrophobic.

Liquid fuels from Canadian coals

Energy Technology Data Exchange (ETDEWEB)

Taylor, G. W.

1979-06-15

In Canadian energy planning, the central issue of security of supply must be addressed by developing flexible energy systems that make the best possible use of available resources. For liquid fuel production, oil sands and heavy oil currently appear more attractive than coal or biomass as alternatives to conventional crude oil, but the magnitude of their economic advantage is uncertain. The existence of large resources of oil sands, heavy oils, natural gas and low-sulfur coals in Western Canada creates a unique opportunity for Canadians to optimize the yield from these resources and develop new technology. Many variations on the three basic liquefaction routes - hydroliquefaction, pyrolysis and synthesis - are under investigation around the world, and the technology is advancing rapidly. Each process has merit under certain circumstances. Surface-mineable subbituminous and lignite coals of Alberta and Saskatchewan appear to offer the best combination of favorable properties, deposit size and mining cost, but other deposits in Alberta, Nova Scotia and British Columbia should not be ruled out. The research effort in Canada is small by world standards, but it is unlikely that technology could be imported that is ideally suited to Canadian conditions. Importing technology is undesirable: innovation or process modification to suit Canadian coals and markets is preferred; coprocessing of coal liquids with bitumen or heavy oils would be a uniquely Canadian, exportable technology. The cost of synthetic crude from coal in Canada is uncertain, estimates ranging from $113 to $220/m/sup 3/ ($18 to $35/bbl). Existing economic evaluations vary widely depending on assumptions, and can be misleading. Product quality is an important consideration.

Relationship between ash content and R{sub 70} self-heating rate of Callide Coal

Energy Technology Data Exchange (ETDEWEB)

Beamish, B. Basil; Blazak, Darren G. [School of Engineering, The University of Queensland, St Lucia, Qld 4072 (Australia)

2005-10-17

Borecore samples from the Trap Gully pit at Callide have been assessed using the R{sub 70} self-heating test. The highest R{sub 70} self-heating rate value was 16.22 {sup o}C/h, which is consistent with the subbituminous rank of the coal. R{sub 70} decreases significantly with increasing mineral matter content, as defined by the ash content of the coal. This effect is due to the mineral matter in the coal acting as a heat sink. A trendline equation has been fitted to the borecore data from the Trap Gully pit: R{sub 70}=0.0029xash{sup 2}-0.4889xash+20.644, where all parameters are on a dry-basis. This relationship can be used to model the self-heating hazard of the pit, both vertically and laterally. (author)

Moisture Management for High R-Value Walls

Energy Technology Data Exchange (ETDEWEB)

Lepage, R. [Building Science Corporation, Somerville, MA (United States); Schumacher, C. [Building Science Corporation, Somerville, MA (United States); Lukachko, A. [Building Science Corporation, Somerville, MA (United States)

2013-11-01

This report explains the moisture-related concerns for high R-value wall assemblies and discusses past Building America research work that informs this study. In this project, hygrothermal simulations were prepared for several common approaches to High R-value wall construction in six cities (Houston, Atlanta, Seattle, St. Louis, Chicago, and International Falls) representing a range of climate zones. The modeling program assessed the moisture durability of the wall assemblies based on three primary sources of moisture: construction moisture, air leakage condensation, and bulk water leakage; the report presents results of the study.

Coal-oil coprocessing at HTI - development and improvement of the technology

Energy Technology Data Exchange (ETDEWEB)

Stalzer, R.H.; Lee, L.K.; Hu, J.; Comolli, A. [Hydrocarbon Technologies, Inc., Lawrenceville, NJ (United States)

1995-12-31

Co-Processing refers to the combined processing of coal and petroleum-derived heavy oil feedstocks. The coal feedstocks used are those typically utilized in direct coal liquefaction: bituminous, subbituminous, and lignites. Petroleum-derived oil, is typically a petroleum residuum, containing at least 70 W% material boiling above 525{degrees}C. The combined coal and oil feedstocks are processed simultaneously with the dual objective of liquefying the coal and upgrading the petroleum-derived residuum to lower boiling (<525{degrees}C) premium products. HTI`s investigation of the Co-Processing technology has included work performed in laboratory, bench and PDU scale operations. The concept of co-processing technology is quite simple and a natural outgrowth of the work done with direct coal liquefaction. A 36 month program to evaluate new process concepts in coal-oil coprocessing at the bench-scale was begun in September 1994 and runs until September 1997. Included in this continuous bench-scale program are provisions to examine new improvements in areas such as: interstage product separation, feedstock concentrations (coal/oil), improved supported/dispersed catalysts, optimization of reactor temperature sequencing, and in-line hydrotreating. This does not preclude other ideas from DOE contracts and other sources that can lead to improved product quality and economics. This research work has led to important findings which significantly increased liquid yields, improved product quality, and improved process economics.

Pyrolysis of coal in the presence of nitric oxide

Energy Technology Data Exchange (ETDEWEB)

Berkowitz, N; Dammeyer, W

1956-01-01

Examination of tars obtained by low-temperature carbonization of a subbituminous coal in the presence of NO suggests that NO will both retard thermal decomposition and inhibit secondary polymerization in the tar phase. But both reactions are subject to the condition that NO is present at the start of incipient pyrolysis (they do not occur if NO is admitted to the retorts at a point above the decomposition temperature of the coal), and their extent depends sharply upon the concentration of NO. At comparatively low partial pressure of NO, the dominant reaction is retardation of decomposition; significant modification of the tar, leading to a greater proportion of low-boiling material, is confined to high-partial pressure of NO. Conclusions, after analyzing tar yields and infrared spectra of tar fractions, are that the inhibition of secondary polymerization in the tar phase involves the transient attachment of NO to primary tar molecules, and that the inhibitory effect of NO is essentially temporary. Tars modified by NO do not appear to be more stable than normal tars in the presence of light, and their composition, as determined by infrared spectroscopy, is not perceptibly different.

Characterization of Activated Carbon from Coal and Its Application as Adsorbent on Mine Acid Water Treatment

OpenAIRE

Siti Hardianti; Susila Arita Rachman; Harminuke E.H.

2017-01-01

Anthracite and Sub-bituminous as activated carbon raw material had been utilized especially in mining field as adsorbent of dangerous heavy metal compound resulted in mining activity. Carbon from coal was activated physically and chemically in various temperature and particle sizes. Characterization was carried out in order to determine the adsorbent specification produced hence can be used and applied accordingly. Proximate and ultimate analysis concluded anthracite has fixed carbon 88.91% w...

Evaluation study on rationalization of coal handling in snowy area

Energy Technology Data Exchange (ETDEWEB)

Suesada, Yasuhiko; Yamagata, Keisuke; Kuwahara, Mitsuhiro

1987-09-25

The adhesion of coal to the coal handling facilities in large cool-fired power plants in the snowy area was investigated for siting them in the future. The amount of water derived from melted snow in addition to that from the rain fall were measured and the statistical amounts of rain and snow falls for the past ten years were examined. Then the amount of water derived from melted snow was calculated by regression. The result indicates that the amount of rain fall in summer is larger than that from melted snow. The moisture content of coal in a coal yard reaches the moisture content at which the coal readily adheres to the facilities after snow fall and it penetrates the pile of coal to the bottom with the lapse of time. The penetrating rate of it largely depends upon the particle distribution of coal as well as the ranks of coal. The adhesion of coal to the coal handling facilities is caused mainly by the amount of dust coal and the moisture content of coal. The amount of adhered coal estimated from the shear properties qualitatively agrees with the experimental result using a model of chute. Adding the dusting inhibitor exceeding the normal value increases the amount of of adhesion of coal. (13 figs, 3 tabs)

Use of moist run-of-mine coal for gasification

Energy Technology Data Exchange (ETDEWEB)

Sowka, K.; Duerlich, M.; Rabe, W. (VEB Gaskombinat Fritz Selbmann, Schwarze Pumpe (German Democratic Republic))

1988-01-01

A Series of experiments was performed in 1982 and 1986 to assess the feasibility of substituting brown coal briquets by raw brown coal in the fixed bed gasification plant for producing town gas at Schwarze Pumpe, GDR. Raw brown coal (50% coal moisture, screened coal of fractions 20 to 80 mm) had to be mixed with dry briquets to maintain a maximum 35% coal charge moisture. Briquet substitution degree varied from 20 to 50%. Short-term gasification tests were also carried out at an experimental generator examining 80 to 100% substitution degrees. Parameters of generator operation that were achieved are provided. Experiments proved that 50% briquet substitution is technologically feasible in industrial plant operation employing unscreened coal containing all coal fines. An economic assessment is further made that shows substantial energy savings in coal drying and briquetting.

Effects of coal storage in air on physical and chemical properties of coal and on gas adsorption

Science.gov (United States)

Mastalerz, Maria; Solano-Acosta, W.; Schimmelmann, A.; Drobniak, A.

2009-01-01

This paper investigates changes in the high-volatile bituminous Lower Block Coal Member from Indiana owing to moisture availability and oxidation in air at ambient pressure and temperature over storage time. Specifically, it investigates changes in chemistry, in surface area, and pore structure, as well as changes in methane and carbon dioxide adsorption capacities. Our results document that the methane adsorption capacity increased by 40%, whereas CO2 adsorption capacity increased by 18% during a 13-month time period. These changes in adsorption are accompanied by changes in chemistry and surface area of the coal. The observed changes in adsorption capacity indicate that special care must be taken when collecting samples and preserving coals until adsorption characteristics are measured in the laboratory. High-pressure isotherms from partially dried coal samples would likely cause overestimation of gas adsorption capacities, lead to a miscalculation of coal-bed methane prospects, and provide deceptively optimistic prognoses for recovery of coal-bed methane or capture of anthropogenic CO2. ?? 2009 Elsevier B.V. All rights reserved.

Survey report for fiscal 1999. Report on basic survey on joint implementation of installing coal moisture control (CMC) facilities

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of the COP3 joint implementation in fiscal 1999, a survey and discussions were given on installing coal moisture control (CMC) facilities in China. The possibility was discussed with the Jinan Steel Group Company and Shougang Company. The subject is a beehive coke furnace, in which coal containing 11% of water is sent to a fluidized bed dryer, and dried up to 6.6%. Stack gas in the coke furnace is used mainly as the drying heat source. The facility consists of a fluidized bed dryer, a dust collector, a coal transporter, and a stack gas recovering device. The energy saving effects made available to the above two companies are as remarkable as 19,868 tons/year and 12,189 tons/year, respectively, as converted to crude oil, and the greenhouse effect gas reduction effect as 61,476 tons/year and 37,715 tons/year, respectively. Because energy price is low in China, the investment recovery time period is set at six years or less as the limit for economic performance evaluation. As a result of the calculation, the recovery time periods for the above two companies were found to be 4.2 and 4.7 years, proving the CMC project highly promising. It is desired that the project will be moved forward once the issues of the fund raising and the discharge right of global warming gas are made clear. (NEDO)

Fiscal 1993 survey of the base arrangement promotion for foreign coal import. Survey of the general situation of Thai coal; 1993 nendo kaigaitan yunyu kiban seibi sokushin chosa. Thai sekitan sogo jijo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

The paper reported the energy situation in Thailand, the present and future status of coal supply/demand, the present situation of environmental policy and air pollution prevention policy and problems concerning coal and the measures for solution, and a possibility of Japan`s cooperation. In Thailand, the total coal supply amount in 1992 is 16.079 million tons, which is 9.1% of all the primary energy supply amount. The country produces only a few amount of anthracite and subbituminous coal beside brown coal. The domestic coal equals brown coal, the production of which was 15.335 million tons in 1992, 13.9% of all the primary energy demand. Concerning brown coal, 79.7% of all the brown coal supply are for electric power use, and others for industrial use such as the cement industry. The remaining reserve in developed areas is 151.4 billion tons, and the proven reserve in undeveloped areas 756 million tons. The demand for import coal was 11.25 million tons in 1996, and is expected to be 201.73 million tons in 2000. The paper pointed out some problems arising from coal production and spread of coal utilization, and described measures to solve the problems and fields where there are possibilities of Japan`s cooperation. 36 refs., 44 figs., 73 tabs.

Coal fired steam generation for heavy oil recovery

International Nuclear Information System (INIS)

Firmin, K.

1992-01-01

In Alberta, some 21,000 m 3 /d of heavy oil and bitumen are produced by in-situ recovery methods involving steam injection. The steam generation requirement is met by standardized natural-gas-fired steam generators. While gas is in plentiful supply in Alberta and therefore competitively priced, significant gas price increases could occur in the future. A 1985 study investigating the alternatives to natural gas as a fuel for steam generation concluded that coal was the most economic alternative, as reserves of subbituminous coal are not only abundant in Alberta but also located relatively close to heavy oil and bitumen production areas. The environmental performance of coal is critical to its acceptance as an alternate fuel to natural gas, and proposed steam generator designs which could burn Alberta coal and control emissions satisfactorily are assessed. Considerations for ash removal, sulfur dioxide sorption, nitrogen oxides control, and particulate emission capture are also presented. A multi-stage slagging type of coal-fired combustor has been developed which is suitable for application with oilfield steam generators and is being commissioned for a demonstration project at the Cold Lake deposit. An economic study showed that the use of coal for steam generation in heavy oil in-situ projects in the Peace River and Cold Lake areas would be economic, compared to natural gas, at fuel price projections and design/cost premises for a project timing in the mid-1990s. 7 figs., 3 tabs

Mineral and inorganic chemical composition of the Pernik coal, Bulgaria

Energy Technology Data Exchange (ETDEWEB)

Yossifova, Mariana G. [Geological Institute, Acad. G. Bonchev Str., Bl.24, Bulgarian Academy of Sciences, 1113 Sofia (Bulgaria)

2007-11-22

The mineral and inorganic chemical composition of five types of samples from the Pernik subbituminous coals and their products generated from the Pernik preparation plant were studied. They include feed coal, low-grade coal, high-grade coal, coal slime, and host rock. The mineral matter of the coals contains 44 species that belong mainly to silicates, carbonates, sulphates, sulphides, and oxides/hydroxides, and to a lesser extent, chlorides, biogenic minerals, and organic minerals. The detrital minerals are quartz, kaolinite, micas, feldspars, magnetite, cristobalite, spessartine, and amphibole. The authigenic minerals include various sulphides, silicates, oxihydroxides, sulphates, and carbonates. Several stages and substages of formation were identified during the syngenetic and epigenetic mineral precipitations of these coals. The authigenic minerals show the greatest diversity of mineral species as the epigenetic mineralization (mostly sulphides, carbonates, and sulphates) dominates qualitatively and quantitatively. The epigenetic mineralization was a result of complex processes occurring mostly during the late development of the Pernik basin. These processes indicate intensive tectonic, hydrothermal and volcanic activities accompanied by a change from fresh to marine sedimentation environment. Thermally altered organic matter due to some of the above processes was also identified in the basin. Most of the trace elements in the Pernik coals (Mo, Be, S, Zr, Y, Cl, Ba, Sc, Ga, Ag, V, P, Br, Ni, Co, Pb, Ca, and Ti) show an affinity to OM and phases intimately associated with OM. Some of the trace elements (Sr, Ti, Mn, Ba, Pb, Cu, Zn, Co, Cr, Ni, As, Ag, Yb, Sn, Ga, Ge, etc.) are impurities in authigenic and accessory minerals, while other trace elements (La, Ba, Cu, Ce, Sb, Bi, Zn, Pb, Cd, Nd, etc.) occur as discrete phases. Elements such as Sc, Be, Y, Ba, V, Zr, S, Mo, Ti, and Ga exceed Clarke concentrations in all of the coal types studied. It was also found that

Briquetting and coking behavior of Bobov-Dol coal

Energy Technology Data Exchange (ETDEWEB)

Naundorf, W.

1987-01-01

Hard Bulgarian glance brown coal (23.2% ash content, 16% coal moisture 2.39% sulfur) was studied for its general suitability for partial black coal coke substitution in coking plants and for the possibility of producing pyrolysis briquets for coking purposes. Laboratory briquetting variants include coal briquetting without binders, with sulfite lye as binder, briquetting after partial demineralization by wet classification, briquetting of different screening fractions (0 to 4 mm), briquetting as a mixture with type 35 caking black coal as well as mixed with type 34 less caking black coal under addition of black coal tar, pitch or bitumen. Coking of the briquets produced was carried at with and without charge compacting. Graphs and tables provide briquetting and coking results. It is concluded that high strength coke can be produced from this brown coal, but it can only be used commercially as heating coke due to its high ash and sulfur content. Briquetting and coking of partially demineralized brown coal in a mixture with black coal and binders resulted in suitable metallurgical coke. Maximum percentage of brown coal in the briquetting mixture was 30%. 4 refs.

Fiscal 1998 New Sunshine Plan auxiliary project. Report on results on development of coal hydrogasification technology (Support research); 1998 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Sekitan suiso tenka gaska gijutsu kaihatsu shien kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

R and D was conducted for the purpose of developing the alternative natural gas manufacturing process that, using coal as the raw material, is highly efficient as well as environmentally superior, with the fiscal 1998 results reported. A hydrogasification test was conducted on Taiheiyo coal at a temperature of 1,173k and a pressure of 7 MPa, which showed that all gaseous products other than methane stopped their evolution roughly in the heat-up process, while methane continued to evolve to show the highest yield. In the reactivity comparison of various types of coal, coals with carbon content of 80% or below were high in reactivity and considered suitable for hydrogasification feedstock. It was also suggested that the hydrogasification reactivity of low rank coals including sub-bituminous coals or below might be greatly affected by the presence/absence of the catalytic effects of ion-exchanged metals. Behavior experiments of sulfur and nitrogen in coal in the hydrogenation reaction were carried out using a continuous free-fall type reactor, which elucidated the effects of hydrogen pressure and gas residence time among various operational elements. (NEDO)

Gas emissions, minerals, and tars associated with three coal fires, Powder River Basin, USA.

Science.gov (United States)

Engle, Mark A; Radke, Lawrence F; Heffern, Edward L; O'Keefe, Jennifer M K; Hower, James C; Smeltzer, Charles D; Hower, Judith M; Olea, Ricardo A; Eatwell, Robert J; Blake, Donald R; Emsbo-Mattingly, Stephen D; Stout, Scott A; Queen, Gerald; Aggen, Kerry L; Kolker, Allan; Prakash, Anupma; Henke, Kevin R; Stracher, Glenn B; Schroeder, Paul A; Román-Colón, Yomayra; ter Schure, Arnout

2012-03-15

Ground-based surveys of three coal fires and airborne surveys of two of the fires were conducted near Sheridan, Wyoming. The fires occur in natural outcrops and in abandoned mines, all containing Paleocene-age subbituminous coals. Diffuse (carbon dioxide (CO(2)) only) and vent (CO(2), carbon monoxide (CO), methane, hydrogen sulfide (H(2)S), and elemental mercury) emission estimates were made for each of the fires. Additionally, gas samples were collected for volatile organic compound (VOC) analysis and showed a large range in variation between vents. The fires produce locally dangerous levels of CO, CO(2), H(2)S, and benzene, among other gases. At one fire in an abandoned coal mine, trends in gas and tar composition followed a change in topography. Total CO(2) fluxes for the fires from airborne, ground-based, and rate of fire advancement estimates ranged from 0.9 to 780mg/s/m(2) and are comparable to other coal fires worldwide. Samples of tar and coal-fire minerals collected from the mouth of vents provided insight into the behavior and formation of the coal fires. Published by Elsevier B.V.

Moisture Management for High R-Value Walls

Energy Technology Data Exchange (ETDEWEB)

Lepage, R.; Schumacher, C.; Lukachko, A.

2013-11-01

The following report explains the moisture-related concerns for High R-value wall assemblies and discusses past Building America research work that informs this study. Hygrothermal simulations were prepared for several common approaches to High R-value wall construction in six cities (Houston, Atlanta, Seattle, St. Louis, Chicago, and International Falls) representing a range of climate zones (2, 3, 4C, 4, 5A, and 7, respectively). The simulations are informed by experience gained from past research in this area and validated by field measurement and forensic experience. The modeling program was developed to assess the moisture durability of the wall assemblies based on three primary sources of moisture: construction moisture, air leakage condensation, and bulk water leakage. The peak annual moisture content of the wood based exterior sheathing was used to comparatively analyze the response to the moisture loads for each of the walls in each given city. Walls which experienced sheathing moisture contents between 20% and 28% were identified as risky, whereas those exceeding 28% were identified as very high risk. All of the wall assemblies perform well under idealized conditions. However, only the walls with exterior insulation, or cavity insulation which provides a hygrothermal function similar to exterior insulation, perform adequately when exposed to moisture loads. Walls with only cavity insulation are particularly susceptible to air leakage condensation. None of the walls performed well when a precipitation based bulk water leak was introduced to the backside of the sheathing, emphasizing the importance of proper flashing details.

Material balance in coal. 2. Oxygen determination and stoichiometry of 33 coals

International Nuclear Information System (INIS)

Volborth, A.; Miller, G.E.; Garner, C.K.; Jerabek, P.A.

1977-01-01

The chemical analysis of coal can be supplemented by the determination of oxygen in high and low temperature ash, in coal as received and in coal dried at 105 0 C. The rapid method utilizes fast-neutron activation. The reaction 16 O(n,p) 16 N and counting of the 6.1 and 7.1 MeV gammas of 7.3 second half-life are used. A specially designed dual transfer and simultaneous counting system gives very accurate results. Oxygen in 33 coals ranging from lignite to low volatile bituminous coal is determined and compared with ''oxygen by difference.'' Considerable discrepancies are observed. Better stoichiometric results are obtained if oxygen in coal ash, in wet coal and in the dried coal is determined. This permits the estimation of the true material balances using data of the ultimate and the proximate coal analysis. The oxygen determination provides the coal chemist with an accurate basis and can be used to rank coal. The summation of the percent of carbon, nitrogen, hydrogen, sulfur, and oxygen becomes more meaningful and some errors can be detected and the state of completeness of coal analysis thus evaluated. Total sulfur can be estimated and oxidation effects during drying can be detected. These affect the moisture determination. It appears that after more data are collected, the interpretation of solid fuel analyses may be facilitated and will be stoichiometrically more meaningful. It is shown that it may be possible to simplify the present time-consuming methods of coal analysis

Continuous online nuclear analyzer of coal

International Nuclear Information System (INIS)

Rogers, R.S.C.; Bozorgmanesh, H.; Gozani, T.; Brown, T.

1980-01-01

Since CONAC is a relatively new concept in coal quality measurement, the present paper concentrates primarily on instrument development. The basic principles of elemental composition, moisture content and Btu measurements are described and typical measurement results presented. Then, since CONAC is under development specifically for quality control purposes, its advantages and potential applications in the coal circuit are discussed. The CONAC development work showed principles of CONAC operation (PNAA, moisture and Btu determinations) to be powerful and versatile tools for the analysis of coal; CONAC-type instrumentation is being developed for batch, laboratory usage. Such a device will enable a user to perform rapid coal sample analyses in a nondestructive fashion, leaving samples intact for further evaluation. It is felt that a batch laboratory, CONAC-type device will be of great use in the mining industry where the analysis of borehole samples are important in the evaluation of coal reserves and in the planning of mining operations

The effect of sulphide and moisture content on steel corrosion during transport of fine wet coal

International Nuclear Information System (INIS)

Waanders, F. B.; Vorster, S. W.

2013-01-01

In the present investigation the influence of compaction pressure (stress) on the corrosivity of wet coal was investigated. Two coal samples, one high in sulphur content (3 %) and the other low in sulphur content (0.6 %) were used to determine the influence of compaction stress on the corrosion rates of steel samples in contact with compacted coal. It was found that the pressure exerted on finely divided wet coal is an important factor in determining its water content and corrosivity towards mild steel. Corrosion of the steel was typically in the form of pitting and the sulphur content of the coal was an important factor in determining the corrosivity of the coal. The corrosion rate of the high sulphur content coal was higher than that of the low sulphur coal. Mössbauer spectroscopy showed that a FeS species developed on the steel surface.

The importance of thermal behaviour and petrographic composition for understanding the characteristics of a Portuguese perhydrous Jurassic coal

Energy Technology Data Exchange (ETDEWEB)

Costa, A. [Centro de Geologia, Universidade do Porto (Portugal); Flores, D. [Centro de Geologia, Universidade do Porto (Portugal); Departamento de Geociencias, Ambiente e Ordenamento do Territorio, Faculdade de Ciencias, Universidade do Porto (Portugal); Suarez-Ruiz, I.; Pevida, C.; Rubiera, F. [Instituto Nacional del Carbon, (INCAR-CSIC), Oviedo (Spain); Iglesias, M.J. [Area de Quimica Organica, Universidad de Almeria (Spain)

2010-12-01

The perhydrous Batalha coal (Portugal) is found in the Cabacos and Montejunto Formation of the Oxfordian-Kimeridgian, Upper Jurassic age. From the macroscopic point of view, its appearance is similar to other perhydrous coals. Microscopically, the maceral group of huminite is the main organic component (96%), ulminite being the most important petrographic component, followed by textinite with resinite (4%) lumina filled. The huminite random reflectance is 0.33%. This coal is characterized by high H/C atomic ratio, and anomalous physical and chemical properties that are characteristic of perhydrous coals such as: (i) the absence of any correlation between reflectance and the chemical rank parameters; (ii) a lower real density than that of non-perhydrous coals; (iii) a high hydrogen content; and (iv) suppressed reflectance. Using its calorific value (moist, ash-free basis) as rank parameter, Batalha coal must be considered a subbituminous A coal. Hydrogen enrichment due to the presence of resinite has influenced the technological properties of this coal, namely: (i) reduction of the thermostability and decrease in the temperature of initial thermal decomposition due to, among other reasons, the existence of aliphatic structures with low dissociation energy bonds resulting from the presence of resinite; (ii) from the DTG profile, the volatile matter combustion and char combustion is not evident; (iii) development of chars made up of isotropic particles with angular edges, which is typical of a low rank coal; (iv) the evolution trend of gaseous compounds (CO, CO{sub 2} and CH{sub 4}) during pyrolysis; and, (v) an increase in its calorific value due to its hydrogen content. The study of this coal which is interbedded in Jurassic formations in the Lusitanian Basin of Portugal is a new contribution to the assessment of the evolution of organic matter in this area. (author)

U and Th in some brown coals of Serbia and Montenegro and their environmental impact.

Science.gov (United States)

Zivotić, Dragana; Grzetić, Ivan; Lorenz, Hans; Simić, Vladimir

2008-03-01

The objective of this paper is to determine and compare the concentrations of U and Th in soft to hard brown (lignite to sub-bituminous) coals of Serbia and Montenegro. It also presents comparison of the obtained data on U and Th concentrations with the published data on coals located in some other countries of the world. Almost the whole coal production of Serbia and Montenegro is used as feed coals for combustion in thermal power plants. Channel samples from open pit and underground mines and core samples were collected for hard and soft brown coals. For the analysis the samples were decomposed using microwave technique. Obtained solutions containing U and Th were analyzed by inductively coupled plasma mass spectroscopy (ICP-MS) using NIST standards. Concentration of U from the investigated basins and the corresponding mine fields ranges within 0.60-70.10 mg/kg, 0.65-3.20 mg/kg, 0.95-6.59 mg/kg, 1.20-6.05 mg/kg, 0.80-6.66 mg/kg, 0.18-89.90 mg/kg, 0.19-4.14 mg/kg, and 0.28-3.52 mg/kg for the Kostolac, Kolubara, Krepoljin, Sjenica, Soko Banja, Bogovina East field, Senje-Resavica and Pljevlja basins, respectively. Concentration of Th ranges within 0.20-2.60 mg/kg, 0.84-6.57 mg/kg, 1.48-6.48 mg/kg, 0.12-2.71 mg/kg, 0.13-4.95 mg/kg, 0.14-3.48 mg/kg, 0.29-3.56 mg/kg, and 0.17-1.89 mg/kg for the Kostolac, Kolubara, Krepoljin, Sjenica, Soko Banja, Bogovina East field, Senje-Resavica and Pljevlja basins, respectively. Brown coal from Senje-Resavica, Kolubara, Kostolac and Pljevlja is characterized by low U concentration. Coals form the Krepoljin, Soko Banja and Sjenica basins have slightly higher U concentrations than the mentioned group. The highest concentration of U is characteristic for the coal from the Bogovina East field. Concentration of Th in coals from Serbia and Montenegro has proved to be low. Out of all investigated coal basins, only the coal from the Krepoljin and Kolubara basins has high concentration of Th. The hydrothermally altered rocks of the Timok

A CHARACTERIZATION AND EVALUATION OF COAL LIQUEFACTION PROCESS STREAMS

International Nuclear Information System (INIS)

G.A. Robbins; R.A. Winschel; S.D. Brandes

1999-01-01

This is the first Annual Technical Report of activities under DOE Contract No. DE-AC22-94PC93054. Activities from the first three quarters of the fiscal 1998 year were reported previously as Quarterly Technical Progress Reports (DOE/PC93054-57, DOE/PC93054-61, and DOE/PC93054-66). Activities for the period July 1 through September 30, 1998, are reported here. This report describes CONSOL's characterization of process-derived samples obtained from HTI Run PB-08. These samples were derived from operations with Black Thunder Mine Wyoming subbituminous coal, simulated mixed waste plastics, and pyrolysis oils derived from waste plastics and waste tires. Comparison of characteristics among the PB-08 samples was made to ascertain the effects of feed composition changes. A comparison also was made to samples from a previous test (Run PB-06) made in the same processing unit, with Black Thunder Mine coal, and in one run condition with co-fed mixed plastics

Reconnaissance coal study in the Susitna basin, 2014

Science.gov (United States)

David L. LePain,; Stanley, Richard G.; Harun, Nina T.; Helmold, Kenneth T.; Tsigonis, Rebekah

2015-01-01

The Alaska Division of Geological & Geophysical Surveys (DGGS) conducted fieldwork during the summer of 2014 in the Susitna basin as part of an ongoing evaluation of the hydrocarbon potential of frontier basins, particularly those near the Railbelt region (for example, Decker and others, 2013; Gillis and others, 2013). Topical studies associated with this recent work include sedimentary facies analysis (LePain and others, 2015) and structural geology investigations (Gillis and others, 2015). The Susitna basin contains coal-bearing Paleogene and Neogene strata correlative with formations that host oil and gas in Cook Inlet basin to its south. Isotopic signatures of natural gas reservoired in the Miocene/Pliocene Sterling and Miocene Beluga Formations suggest a biogenic origin for Cook Inlet gas (Claypool and others, 1980). To assess the biogenic gas potential of the Susitna basin, it is important to obtain information from its coal-bearing units.Characteristics of coal, such as maturity/rank and cleat development are key parameters influencing viability of a biogenic gas system (Laubach and others, 1998). In an early study of the Susitna basin (Beluga–Yentna region), Barnes (1966) identified, analyzed, and recognized potentially valuable subbituminous coal resources at Fairview Mountain, Canyon Creek, and Johnson Creek. Merritt (1990), in a sedimentological study to evaluate surface coal mining potential of the Tertiary rocks of the Susitna basin (Susitna lowland), concluded that the basin contained several billion tons of mineable reserves. This preliminary report offers a brief summary of new information on coals in the Susitna Basin acquired during associated stratigraphic studies (see LePain and others, 2015). 

Advanced liquefaction using coal swelling and catalyst dispersion techniques. Volume 2, appendices. Final technical report, October 1, 1991--September 30, 1994

Energy Technology Data Exchange (ETDEWEB)

Curtis, C.W. [Auburn Univ., AL (United States); Chander, S. [Pennsylvania State Univ., College Park, PA (United States); Gutterman, C.

1995-04-01

Liquefaction experiments were undertaken using subbituminous Black Thunder mine coal to observe the effects of aqueous SO{sub 2} coal beneficiation and the introduction of various coal swelling solvents and catalyst precursors. Aqueous SO{sub 2} beneficiation of Black Thunder coal removed alkali metals and alkaline earth metals, increased the sulfur content and increased the catalytic liquefaction conversion to THF solubles compared to untreated Black Thunder coal. The liquefaction solvent had varying effects on coal conversion, depending upon the type of solvent added. The hydrogen donor solvent, dihydroanthracene, was most effective, while a coal-derived Wilsonville solvent promoted more coal conversion than did relatively inert 1-methylnaphthalene. Swelling of coal with hydrogen bonding solvents tetrahydrofuran (THF), isopropanol, and methanol, prior to reaction resulted in increased noncatalytic conversion of both untreated and SO{sub 2} treated Black Thunder coals, while dimethylsulfoxide (DMSO), which was absorbed more into the coal than any other swelling solvent, was detrimental to coal conversion. Swelling of SO{sub 2} treated coal before liquefaction resulted in the highest coal conversions; however, the untreated coal showed the most improvements in catalytic reactions when swelled in either THF, isopropanol, or methanol prior to liquefaction. The aprotic solvent DMSO was detrimental to coal conversion.

Entrained bed gasification of coal: prediction of contaminant levels using thermodynamic calculations

Energy Technology Data Exchange (ETDEWEB)

Furimsky, E.; Zheng, L.; Boudreau, F.; Kovacik, G. (CANMET, Ottawa, ON (Canada). Energy Research Labs.)

1993-10-01

The F.A.C.T. method was used for predicting the emissions of S-, Cl-, N-, Pb- and As-containing contaminants from entrained bed gasification of one bituminous coal and one subbituminous coal. When the effect of mineral matter was included, the emissions of H[sub 2]S, CS[sub 2], COS, HCl and HCN decreased substantially whereas the amount of predicted NH[sub 3] remained unaffected. The decrease was offset by increased formation of metal sulphides, chlorides and cyanides. Relatively large amounts of Na, K, Mg, Ca, Pb and As in the gas were predicted by the method. The chlorides of these metals are also rather volatile. The presence of steam increased the amount of H[sub 2]S and HCl and decreased the amount of HCN in the products. 8 refs., 5 figs., 5 tabs.

A Technique for Decreasing Reactivity of Coal Material to Suppress the Oxygen Absorption Process

OpenAIRE

Timofeeva, S. S.; Lugovtsova, Nataliya Yurievna; Gubanova, А. R.

2016-01-01

The paper describes the mechanisms of self-ignition formation in coal liable to spontaneous combustion, on the basis of experimental works performed to analyze heat and mass transfer in the coal-air system. A new approach was developed to the coal self-heating suppression and thermodynamic control of the oxidation process. The influence of coal moisture content and thermal behaviour of air in the cooling process was studied during moisture evaporation.

JV Task 126 - Mercury Control Technologies for Electric Utilities Burning Bituminous Coal

Energy Technology Data Exchange (ETDEWEB)

Jason Laumb; John Kay; Michael Jones; Brandon Pavlish; Nicholas Lentz; Donald McCollor; Kevin Galbreath

2009-03-29

The EERC developed an applied research consortium project to test cost-effective mercury (Hg) control technologies for utilities burning bituminous coals. The project goal was to test innovative Hg control technologies that have the potential to reduce Hg emissions from bituminous coal-fired power plants by {ge}90% at costs of one-half to three-quarters of current estimates for activated carbon injection (ACI). Hg control technology evaluations were performed using the EERC's combustion test facility (CTF). The CTF was fired on pulverized bituminous coals at 550,000 Btu/hr (580 MJ/hr). The CTF was configured with the following air pollution control devices (APCDs): selective catalytic reduction (SCR) unit, electrostatic precipitator (ESP), and wet flue gas desulfurization system (WFDS). The Hg control technologies investigated as part of this project included ACI (three Norit Americas, Inc., and eleven Envergex sorbents), elemental mercury (Hg{sup 0}) oxidation catalysts (i.e., the noble metals in Hitachi Zosen, Cormetech, and Hitachi SCR catalysts), sorbent enhancement additives (SEAs) (a proprietary EERC additive, trona, and limestone), and blending with a Powder River Basin (PRB) subbituminous coal. These Hg control technologies were evaluated separately, and many were also tested in combination.

Bioremediation potential of coal-tar-oil-contaminated soil

International Nuclear Information System (INIS)

Lajoie, C.A.

1991-01-01

The bioremediation of coal tar oil contaminated soil was investigated in 90 day laboratory simulation experiments. The effect of soil moisture, humic acid amendment, and coal tar oil concentration on the rate of disappearance of individual coal tar oil constituents (PAHs and related compounds) was determined by methylene chloride extraction and gas chromatography. Mass balance experiments determined the fate of both the individual 14 C-labeled PAHs phenanthrene, pyrene, and benzo(a)pyrene, and the total coal tar oil carbon. Mineralization, volatilization, incorporation into microbial biomass, disappearance of individual coal tar oil constitutents, and the distribution of residual 14 C-activity in different soil fractions were measured. The rate of disappearance of coal tar oil constituents increased with increasing soil moisture over the experimental range. Humic acid amendment initially enhanced the rate of disappearance, but decreased the extent of disappearance. The amount of contamination removed decreased at higher coal tar oil concentrations. The practical limit for biodegradation in the system tested appeared to be between 1.0 and 2.5% coal tar oil. Mineralization accounted for 40 to 50% of the applied coal tar oil. Volatilization was a minor pathway of disappearance

The impact of anaerobic microorganisms activities in ruminant waste and coal

Science.gov (United States)

Harlia, Ellin; Hamdani, H.; Winantris, Kurnani, Tb. B. A.; Hidayati, Y. A.; Marlina, E. T.; Rahmah, K. N.; Arief, H.; Ridwan, R.; Joni, I. M.

2018-02-01

Ruminant (dairy cattle, beef cattle and buffalo) waste from intensive farming concentrated in highly populated areas when stacked and accumulated in certain heights and in anaerobic condition, may produce Green House Gases (GHGs) which lead to global warming. This condition is generated through fermentation by microorganism contained in livestock waste and biogenic activities on coal. The GHGs include CH4 (methane), CO2 (carbon dioxide) and N2O (nitrous oxide). The GHG emission should be early monitored to minimize greater problems. In the other hand, methane can be utilized as an environmental friendly energy after stored as biogas on digester. The aim of this research is to detect how much GHGs formed from ruminant waste and biogenic activities on coal, which can be utilized as an alternative energy. This research conducted as an explorative study utilizing dairy cattle feces, beef cattle feces, buffalo feces and three types of coal: lignite, bituminous and sub-bituminous, which is separately added into medium 98-5 made from mixture of agar medium and chemical components in powder and crystal form diluted with distilled water and rumen liquid, with six repetitions. Each sample was stored into 250 mL anaerobic digester, observed weekly for period of 4 weeks, analyzed by Gas Chromatography (GC-A14). The result showed that GHGs: CH4, CO2 and N2O were found in all samples. Anticipation of GHGs formation to avoid air pollution is by utilizing livestock waste and coal in aerobic condition or in anaerobic condition through digester.

Petrographic characteristics and depositional environment of Miocene Can coals, Canakkale-Turkey

Energy Technology Data Exchange (ETDEWEB)

Guerdal, Guelbin; Bozcu, Mustafa [Canakkale Onsekiz Mart University, Engineering and Architecture Faculty (Turkey)

2011-01-01

In this study, petrographic examinations along with proximate, calorific value, ultimate, sulphur form and XRD analyses were performed in order to determine the coal characteristics and the depositional environment of the Miocene Can coals. Seventy coal samples were taken from cores and open pit mines. The investigated Can coals are humic coals and classified as lignite to sub-bituminous coal based on the random huminite reflectance (0.38-0.54% R{sub r}), volatile matter (45.50-62.25 wt.%, daf) and calorific value (3419-6479 kcal/kg, maf). The sulphur content of the Can coals changes from 0.30 up to 12.23 wt.%, and a broad range of ash contents was observed varying between 2.46 wt.% and 41.19 wt.%. Huminite is the most abundant maceral group (74-95 vol.% mmf) consisting of mostly humocollinite (gelinite) which is followed by relatively low liptinite (2-18 vol.% mmf) and inertinite content (2-13 vol.% mmf). In general, major mineral contents of coal samples are clay minerals, quartz, mica, pyrite and feldspar. The Can-Etili lignite basin consists of mainly volcano-clastics, fluviatile and lacustrine clastic sediments and contains only one lignite seam with 17 m average thickness. In order to assess the development of paleo-mires, coal facies diagrams were obtained from maceral composition. According to the Vegetation Index (VI) and Ground Water Index (GWI), the Can coal accumulated in inundated marsh, limnic and swamp environments under a rheotrophic hydrological regime. In general, the facies interpretations are in accordance with the observed sedimentalogical data. (author)

Inelastic neutron scattering method in hard coal quality monitoring

International Nuclear Information System (INIS)

Cywicka-Jakiel, T.; Loskiewicz, J.; Tracz, G.

1994-07-01

Nuclear methods in mining industry and power generation plants are nowadays very important especially because of the need for optimization of combustion processes and reduction of environmental pollution. On-line analysis of coal quality not only economic benefits but contribute to environmental protection too. Neutron methods especially inelastic scattering and PGNAA are very useful for analysis of coal quality where calorific valve, ash and moisture content are the most important. Using Pu-Be or Am-Be isotopic sources and measuring carbon 4.43 MeV γ-rays from neutron inelastic scattering: 12 C(n,n'γ) 12 C we can evaluate calorific valve in hard coals with precision better than in PGNAA method. This is mainly because of large cross-section for inelastic scattering and the strong correlation between carbon content and calorific value shown in the paper for different coal basins. The influence of moisture on 4.43 MeV carbon γ-rays in considered in the paper in theoretical and experimental aspects and appropriate formula is introduced. Also the possibilities of determine ash, moisture, Cl, Na and Si in coal are shown. (author). 11 refs, 15 figs

Inelastic neutron scattering method in hard coal quality monitoring

Energy Technology Data Exchange (ETDEWEB)

Cywicka-Jakiel, T.; Loskiewicz, J.; Tracz, G. [Institute of Nuclear Physics, Cracow (Poland)

1994-07-01

Nuclear methods in mining industry and power generation plants are nowadays very important especially because of the need for optimization of combustion processes and reduction of environmental pollution. On-line analysis of coal quality not only economic benefits but contribute to environmental protection too. Neutron methods especially inelastic scattering and PGNAA are very useful for analysis of coal quality where calorific valve, ash and moisture content are the most important. Using Pu-Be or Am-Be isotopic sources and measuring carbon 4.43 MeV {gamma}-rays from neutron inelastic scattering: {sup 12}C(n,n`{gamma}){sup 12}C we can evaluate calorific valve in hard coals with precision better than in PGNAA method. This is mainly because of large cross-section for inelastic scattering and the strong correlation between carbon content and calorific value shown in the paper for different coal basins. The influence of moisture on 4.43 MeV carbon {gamma}-rays in considered in the paper in theoretical and experimental aspects and appropriate formula is introduced. Also the possibilities of determine ash, moisture, Cl, Na and Si in coal are shown. (author). 11 refs, 15 figs.

Investigation of the remaining major and trace elements in clean coal generated by organic solvent extraction

Energy Technology Data Exchange (ETDEWEB)

Jie Wang; Chunqi Li; Kinya Sakanishi; Tetsuya Nakazato; Hiroaki Tao; Toshimasa Takanohashi; Takayuki Takarada; Ikuo Saito [National Institute Advanced Industrial Science and Technology (AIST), Ibaraki (Japan). Energy Technology Research Institute

2005-09-01

A sub-bituminous Wyodak coal (WD coal) and a bituminous Illinois No. 6 coal (IL coal) were thermally extracted with 1-methylnaphthalene (1-MN) and N-methyl-2-pyrrolidone (NMP) to produce clean extract. A mild pretreatment with acetic acid was also carried out. Major and trace inorganic elements in the raw coals and resultant extracts were determined by means of inductively coupled plasma optical emission spectrometry (ICP-OES), flow injection inductively coupled plasma mass spectrometry (FI-ICP-MS), and cold vapor atomic absorption spectrometry (CV-AAS). It was found that the extraction with 1-MN resulted in 73-100% reductions in the concentration of Li, Be, V, Ga, As, Se, Sr, Cd, Ba, Hg, and Pb. The extraction with NMP yielded more extract than that with 1-MN, but it retained more organically associated major and trace metals in the extracts. In the extraction of WD coal with NMP, the acid pretreatment not only significantly enhanced the extraction yield but also significantly reduced the concentrations of alkaline earth elements such as Be, Ca, Mg, Sr, and Ba in the extract. In addition, the modes of occurrence of trace elements in the coals were discussed according to their extraction behaviors. 30 refs., 2 figs., 5 tabs.

Influence of the microwave irradiation dewatering on the combustion characteristics of Chinese brown coals

Science.gov (United States)

Ge, Lichao; Feng, Hongcui; Xu, Chang; Zhang, Yanwei; Wang, Zhihua

2018-02-01

This study investigates the influence of microwave irradiation on coal composition, pore structure, coal rank, and combustion characteristics of typical brown coals in China. Results show that the upgrading process significantly decreased the inherent moisture, and increased calorific value and fixed carbon content. After upgrading, pore distribution extended to micropore region, oxygen functional groups were reduced and destroyed, and the apparent aromaticity increased suggesting an improvement in the coal rank. Based on thermogravimetric analysis, the combustion processes of upgraded coals were delayed toward the high temperature region, and the temperatures of ignition, peak and burnout increased. Based on the average combustion rate and comprehensive combustion parameter, the upgraded coals performed better compared with raw brown coals and a high rank coal. In ignition and burnout segments, the activation energy increased but exhibited a decrease in the combustion stage.

Chemical looping coal gasification with calcium ferrite and barium ferrite via solid–solid reactions

International Nuclear Information System (INIS)

Siriwardane, Ranjani; Riley, Jarrett; Tian, Hanjing; Richards, George

2016-01-01

Highlights: • BaFe 2 O 4 and CaFe 2 O 4 are excellent for chemical looping coal gasification. • BaFe 2 O 4 and CaFe 2 O 4 have minimal reactivity with synthesis gas. • Steam enhances the gasification process with these oxygen carriers. • Reaction rates of steam gasification of coal with CaFe 2 O 4 was better than with gaseous oxygen. • Coal gasification appears to be via solid–solid interaction with the oxygen carrier. - Abstract: Coal gasification to produce synthesis gas by chemical looping was investigated with two oxygen carriers, barium ferrite (BaFe 2 O 4 ) and calcium ferrite (CaFe 2 O 4 ). Thermo-gravimetric analysis (TGA) and fixed-bed flow reactor data indicated that a solid–solid interaction occurred between oxygen carriers and coal to produce synthesis gas. Both thermodynamic analysis and experimental data indicated that BaFe 2 O 4 and CaFe 2 O 4 have high reactivity with coal but have a low reactivity with synthesis gas, which makes them very attractive for the coal gasification process. Adding steam increased the production of hydrogen (H 2 ) and carbon monoxide (CO), but carbon dioxide (CO 2 ) remained low because these oxygen carriers have minimal reactivity with H 2 and CO. Therefore, the combined steam–oxygen carrier produced the highest quantity of synthesis gas. It appeared that neither the water–gas shift reaction nor the water splitting reaction promoted additional H 2 formation with the oxygen carriers when steam was present. Wyodak coal, which is a sub-bituminous coal, had the best gasification yield with oxygen carrier–steam while Illinois #6 coal had the lowest. The rate of gasification and selectivity for synthesis gas production was significantly higher when these oxygen carriers were present during steam gasification of coal. The rates and synthesis gas yields during the temperature ramps of coal–steam with oxygen carriers were better than with gaseous oxygen.

The study of high precision neutron moisture gauge

International Nuclear Information System (INIS)

Liu Shengkang; Bao Guanxiong; Sang Hai; Zhu Yuzhen

1993-01-01

The principle, structure and calibration experiment of the high precision neutron moisture gauge (insertion type) are described. The gauge has been appraised. The precision of the measuring moisture of coke is lower than 0.5%, and the range of the measuring moisture is 2%-12%. The economic benefit of the gauge application is good

Advanced physical fine coal cleaning spherical agglomeration. Final report

Energy Technology Data Exchange (ETDEWEB)

1990-09-01

The project included process development, engineering, construction, and operation of a 1/3 tph proof-of-concept (POC) spherical agglomeration test module. The POC tests demonstrated that physical cleaning of ultrafine coal by agglomeration using heptane can achieve: (1) Pyritic sulfur reductions beyond that possible with conventional coal cleaning methods; (2) coal ash contents below those which can be obtained by conventional coal cleaning methods at comparable energy recoveries; (3) energy recoveries of 80 percent or greater measured against the raw coal energy content; (4) complete recovery of the heptane bridging liquid from the agglomerates; and (5) production of agglomerates with 3/8-inch size and less than 30 percent moisture. Test results met or exceeded all of the program objectives. Nominal 3/8-inch size agglomerates with less than 20 percent moisture were produced. The clean coal ash content varied between 1.5 to 5.5 percent by weight (dry basis) depending on feed coal type. Ash reductions of the run-of-mine (ROM) coal were 77 to 83 percent. ROM pyritic sulfur reductions varied from 86 to 90 percent for the three test coals, equating to total sulfur reductions of 47 to 72 percent.

Study of the correlation between the coal calorific value and coal ash content using X-ray fluorescence analysis

International Nuclear Information System (INIS)

Bolortuya, D.; Zuzaan, P.; Gustova, M.V.; Maslov, O.D.

2013-01-01

In this paper we have studied the possibility of determining the chemical elements in coal samples using X-ray fluorescence analysis and have found a relationship between the coal calorific value and its ash content with the coal moisture accounting. The amount of coal ash can be determined by the content of the basic chemical elements, such as Si, Sr, Fe, and Ca. It was concluded that the calorific value of coal can be estimated from the ash content in coal without the calorimetric measurements. These correlation coefficients were calculated for several coal mines in Mongolia. The results are in good agreement with the results of chemical analysis

Report on the FY 1987 potential survey of overseas coal development. Himalian area, Semirara island and San Miguel, Mindanao island, the Philippines; 1987 nendo kaigaitan kaihatsu kanosei chosa hokokusho. Philippines Semirara to Himalian chiku Mindanao to Miguel chiku

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-03-01

Out of the ASEAN countries, the Philippines is not rich in coal resource. The coal reserve is 3.7 million tons, which is only about 1/3 of that in Indonesia, 11.47 million tons. The coal is the one in the young period in quality, and most of the coal except that form the Cebu island is the low grade coal belonging from lignite to sub-bituminous C. The coal in the Himalian area, Semirara island, is expected to be supplied to Calaca No. 2 coal thermal power plant which is planned to be constructed in the south of Luzon island. If it agrees to the power plant side in terms of the coal quality specifications and the price, there is a great possibility of concluding a long-term contract on business. It may be said that developmental potentiality is great. Accordingly, it is important to enhance the quality of the study of developmental possibility in the Himalian area in future. On the other hand, the coal in the San Miguel area, Mindanao island, is extremely high in ash content, and has a problem on coal quality. The developmental potentiality is low. The developmental potentiality of the coal of the Himalian area is high, but the necessity of exporting it to Japan is low since there are no coal thermal power plants which use this kind of low grade coal in Japan. (NEDO)

Carbon-free hydrogen production from low rank coal

Science.gov (United States)

Aziz, Muhammad; Oda, Takuya; Kashiwagi, Takao

2018-02-01

Novel carbon-free integrated system of hydrogen production and storage from low rank coal is proposed and evaluated. To measure the optimum energy efficiency, two different systems employing different chemical looping technologies are modeled. The first integrated system consists of coal drying, gasification, syngas chemical looping, and hydrogenation. On the other hand, the second system combines coal drying, coal direct chemical looping, and hydrogenation. In addition, in order to cover the consumed electricity and recover the energy, combined cycle is adopted as addition module for power generation. The objective of the study is to find the best system having the highest performance in terms of total energy efficiency, including hydrogen production efficiency and power generation efficiency. To achieve a thorough energy/heat circulation throughout each module and the whole integrated system, enhanced process integration technology is employed. It basically incorporates two core basic technologies: exergy recovery and process integration. Several operating parameters including target moisture content in drying module, operating pressure in chemical looping module, are observed in terms of their influence to energy efficiency. From process modeling and calculation, two integrated systems can realize high total energy efficiency, higher than 60%. However, the system employing coal direct chemical looping represents higher energy efficiency, including hydrogen production and power generation, which is about 83%. In addition, optimum target moisture content in drying and operating pressure in chemical looping also have been defined.

Determination of mercury in coal by isotope dilution cold-vapor generation inductively coupled plasma mass spectrometry

Energy Technology Data Exchange (ETDEWEB)

Long, S.E.; Kelly, W.R.

2002-04-01

A method based on isotope dilution cold-vapor inductively coupled plasma mass spectrometry (ID-CV-ICPMS) has been developed for high-accuracy determinations of mercury in bituminous and sub-bituminous coals. A closed-system digestion process employing a Carius tube is used to completely oxidize the coal matrix and chemically equilibrate the mercury in the sample with a Hg-201 isotopic spike. The digestates are diluted with high-purity quartz-distilled water, and the mercury is released as a vapor by reduction with tin chloride. Measurements of Hg-201/Hg-202 isotope ratios are made using a quadrupole ICPMS system in time-resolved analysis mode. The new method has some significant advantages over existing methods. The instrument detection limit is less than 1 pg/mL. The average blank (n = 17) is 30 pg, which is roughly 1 order of magnitude lower than the equivalent microwave digestion procedure. The detection limit in coal is blank limited and is similar to 40 pg/g. Memory effects are very low. The relative reproducibility of the analytical measurements is similar to 0.5% for mercury concentrations in the range 10-150 ng/g. The method has been used to measure mercury concentrations in six coal reference materials, SRM 1632b (77.4 ng/g), SRM 1632c (94.3 ng/g), BCR 40 (433.2 ng/g), BCR 180 (125.0 ng/g), BCR 181 (135.8 ng/g), and SARM 20 (252.6 ng/g), as well as a coal fly ash, SRM 1633b (143.1 ng/g). The method is equally applicable to other types of fossil fuels including both crude and refined oils.

Fluidised bed gasification of low grade South African coals

CSIR Research Space (South Africa)

North, BC

2006-09-01

Full Text Available gasifiers. Fluidised bed Entrained flow Coal particle size 0.5 mm – 5 mm 0 – 0.5 mm Coal moisture Dry Dry/slurry Coal type Non-caking coals Any coal Ash in coal < 60% < 30% Gasification agents Air/steam/oxygen Steam/oxygen Gasification... properties important for fluidised bed gasification are: square4 Coal reactivity in atmospheres of CO2 and H2O square4 Caking index and free swelling index (FSI) square4 Ash fusion temperature (AFT) 5.1 Coal reactivity The gasifcation reactions (1...

Fast and safe gas detection from underground coal fire by drone fly over

International Nuclear Information System (INIS)

Dunnington, Lucila; Nakagawa, Masami

2017-01-01

Underground coal fires start naturally or as a result of human activities. Besides burning away the important non-renewable energy resource and causing financial losses, burning coal seams emit carbon dioxide, carbon monoxide, sulfur oxide and methane, and is a leading cause of smog, acid rain, global warming, and air toxins. In the U.S. alone, the combined cost of coal-fire remediation projects that have been completed, budgeted, or projected by the U.S. Department of the Interior's Office of Surface Mining Remediation and Enforcement (OSM), exceeds $1 billion. It is estimated that these fires generate as much as 3% of the world's annual carbon dioxide emissions and consume as much as 5% of its minable coal. Considering the magnitude of environmental impact and economic loss caused by burning underground coal seams, we have developed a new, safe, reliable surface measurement of coal fire gases to assess the nature of underground coal fires. We use a drone mounted with gas sensors. Drone collected gas concentration data provides a safe alternative for evaluating the rank of a burning coal seam. In this study, a new method of determining coal rank by gas ratios is developed. Coal rank is valuable for defining parameters of a coal seam such as burn temperature, burn rate, and volume of burning seam. - Graphical abstract: Concluding Figure for Gas Ratios: Plotted points and ranges of adjusted literature data. Stars represent bituminous and subbituminous coal types; Ovals represent lignite. - Highlights: • Recognize underground coal fire as a potential source of energy. • Developed a creative, safe, reliable and fast gas detection method. • Developed a concept of gas ratio measurement method that can provide more accurate description of underground burning coal resource.

Task 27 -- Alaskan low-rank coal-water fuel demonstration project

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-01

Development of coal-water-fuel (CWF) technology has to-date been predicated on the use of high-rank bituminous coal only, and until now the high inherent moisture content of low-rank coal has precluded its use for CWF production. The unique feature of the Alaskan project is the integration of hot-water-drying (HWD) into CWF technology as a beneficiation process. Hot-water-drying is an EERC developed technology unavailable to the competition that allows the range of CWF feedstock to be extended to low-rank coals. The primary objective of the Alaskan Project, is to promote interest in the CWF marketplace by demonstrating the commercial viability of low-rank coal-water-fuel (LRCWF). While commercialization plans cannot be finalized until the implementation and results of the Alaskan LRCWF Project are known and evaluated, this report has been prepared to specifically address issues concerning business objectives for the project, and outline a market development plan for meeting those objectives.

Evaluation of paramagnetic species in coals with iodine doping technique; Yoso tenkaho wo mochiita sekitanchu no jojiseishu no hyoka

Energy Technology Data Exchange (ETDEWEB)

Aizawa, S.; Kumagai, H.; Chiba, T. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology

1996-10-28

Electron paramagnetic resonance (EPR) of coals was considered by using iodine doping technique. Sub-bituminous coal (WA) and bituminous coal (UF) were used to observe EPR spectra using microwaves. With the UF coal, strength of the narrow component of the spectra was found constant regardless of amount of the doped iodine, wherein radicals without interaction with iodine were detected. Strength of the broad component increased with the iodine doping amount, where in deviation of {pi} electrons was detected, which have been generated as a result of interaction between aromatic rings and iodine in the coals. Spin concentration of the WA coal with low coalification degree is constant regardless of the iodine doping amount, and the interaction of the iodine with the aromatic rings was found small. The higher the coalification degree, the more the aromatic ring structure grows, and electron donor capability for the iodine increases. In a system with the entire spin being uniform, the spectrum height shows a saturation phenomenon against increase in microwave output. A non-uniform system, in which the oriented spin forms small groups and is in local thermal equilibrium, does not show saturation, but increases monotonously. 2 refs., 5 figs.

Reduced emissions from inexpensive high-sulphur coal briquettes

International Nuclear Information System (INIS)

Gammage, R.B.; Wachter, E.A.; Wade, J.; Wilson, D.L.; Haas, J.W.; Ahmad, N.; Siltain, F.; Raza, M.Z.

1992-01-01

Airborne emissions were measured during the combustion of Pakistani high-sulphur coal, cold briquetted with lime and clay; comparison was made to emissions from raw coal and traditional fuels burnt in a native, mud-lined Angethi stove. Compared to raw coal, the amended coal gave fourfold reduced emission of respirable-size particles (RSP) and threefold reduced total releases of SO 2 . In domestic cooking, substitution of the amended coal briquettes for traditional fuels will not worsen indoor air quality with respect to CO, SO 2 , NO x , and RSP. The high peak amounts of CO (100--250 ppm), SO 2 (2--5 ppm), and NO x (1--5 ppm) were limited to the early phase of burning. The high thermal value of the coal briquettes together with a simple briquetting technology, make this fuel an attractive energy alternative in countries that are underdeveloped, developing, or experiencing major restructuring

Bulk analysis of coal

International Nuclear Information System (INIS)

Sowerby, B.D.

1982-01-01

Nuclear techniques used in the coal industry to determine specific energy, ash and moisture are outlined. Ash analysis by radioisotope X-ray techniques include a single X-ray measurement using a transmission or backscatter geometry and techniques with compensation for iron variations. Neutron techniques can be used to measure the concentration of some specific elements in coal. The measurement of specific energy, ash and moisture then depends on the correlation of the particular parameter with the measured elemental composition. Carbon can be determined by a combination of a measurement of 4.43 MeV 12 C gamma-rays from neutron inelastic scattering with a separate 60 Co gamma-ray scattering measurement. Sulphur meters are based on the measurement of 5.42 MeV neutron capture of gamma rays

Molecular accessibility in solvent swelled coals. Quarterly report, [April--June 1993

Energy Technology Data Exchange (ETDEWEB)

Kispert, L.D.

1993-08-01

The effect of weathering (oxidation and dehydration upon exposure to air) on the molecular accessibility of potential catalysts was studied by the EPR spin probe technique. Fresh samples of all 8 APCS coals were exposed to air for periods up to 36 days. Weathering produced significant effects on the retention of spin probes in most of the APCS coals under 91 % carbon (dmmf). It was determined that the lower ranked coal (Beulah Zap and Wyodak) under went a structural collapse which precluded retention of even spin probe VIII. However, medium ranked coals exhibited improved retention upon weathering when swelled in toluene. Swelling with pyridine opened up small pores for 81--86% carbon which is not observed for swelling with toluene. Changes in coal structure were successfully followed by the EPR spin probe method. A detailed analysis of the data collected from the swelling of coals oxidized in a moisture free environment was completed to differentiate between weathering and oxidation. Eight vacuum dried APCS coals were oxidized in an enclosed, pure oxygen, moisture free environment, and the effects of oxidation alone on coal structure were studied by the intercalation of EPR spin probes. The data shows a factor of 5 increase in spin probe retention for some coals oxidized in O{sub 2} versus air., suggesting a large increase in oxidized material. Particular care was taken during the swelling procedures to avoid exposure of the coal samples to air or moisture. EPR spectra were then obtained for these 300 samples.

BTX production by in-situ contact reforming of low-temperature tar from coal with zeolite-derived catalysts; Zeolite kei shokubai wo mochiita sekitan teion tar no sesshoku kaishitsu ni yoru BTX no seisei

Energy Technology Data Exchange (ETDEWEB)

Matsunaga, T.; Fuda, K.; Murakami, K.; Kyo, M.; Hosoya, S.; Kobayashi, S. [Akita University, Akita (Japan). Mining College

1996-10-28

On BTX production process from low-temperature tar obtained by pyrolysis of coal, the effect of exchanged metallic species and reaction temperature were studied using metallic ion-exchanged Y-zeolite as catalyst. In experiment, three kinds of coals with different produced tar structures such as Taiheiyo and PSOC-830 sub-bituminous coals and Loy Yang brown coal were used. Y-zeolite ion-exchanged with metal chloride aqueous solution was used as catalyst. Zn{sup 2+}, Ni{sup 2+} and In{sup 3+} were used as metal ions to be exchanged. The experiment was conducted by heating a pyrolysis section up to 600{degree}C for one hour after preheating a contact reforming section up to a certain proper temperature. As a result, the Ni system catalyst was effective for BTX production from aromatic-abundant tar, while the Zn system one from lower aromatic tar. In general, relatively high yields of toluene and xylene were obtained at lower temperature, while those of benzene at higher temperature. 4 figs., 1 tab.

POC-scale testing of an advanced fine coal dewatering equipment/technique

Energy Technology Data Exchange (ETDEWEB)

Groppo, J.G.; Parekh, B.K. [Univ. of Kentucky, Lexington, KY (United States); Rawls, P. [Department of Energy, Pittsburgh, PA (United States)

1995-11-01

Froth flotation technique is an effective and efficient process for recovering of ultra-fine (minus 74 {mu}m) clean coal. Economical dewatering of an ultra-fine clean coal product to a 20 percent level moisture will be an important step in successful implementation of the advanced cleaning processes. This project is a step in the Department of Energy`s program to show that ultra-clean coal could be effectively dewatered to 20 percent or lower moisture using either conventional or advanced dewatering techniques. As the contract title suggests, the main focus of the program is on proof-of-concept testing of a dewatering technique for a fine clean coal product. The coal industry is reluctant to use the advanced fine coal recovery technology due to the non-availability of an economical dewatering process. in fact, in a recent survey conducted by U.S. DOE and Battelle, dewatering of fine clean coal was identified as the number one priority for the coal industry. This project will attempt to demonstrate an efficient and economic fine clean coal slurry dewatering process.

Geology and coal resources of the Hanging Woman Creek Study Area, Big Horn and Powder River Counties, Montana

Science.gov (United States)

Culbertson, William Craven; Hatch, Joseph R.; Affolter, Ronald H.

1978-01-01

In an area of 7,200 acres (29 sq km) In the Hanging Woman Creek study area, the Anderson coal bed contains potentially surface minable resources of 378 million short tons (343 million metric tons) of subbituminous C coal that ranges in thickness from 26 to 33 feet (7.9-10.1 m) at depths of less than 200 feet (60 m). Additional potentially surface minable resources of 55 million short tons (50 million metric tons) are contained in the 9-12 foot (2.7-3.7 m) thick Dietz coal bed which lies 50-100 feet (15-30 m) below the Anderson. Analyses of coal from 5 core holes indicates that the Anderson bed contains 0.4 percent sulfur, 5 percent ash, and has a heating value of 8,540 Btu/lb (4,750 Kcal/kg). The trace element content of the coal is generally similar to other coals in the Powder River Basin. The two coal beds are in the Fort Union Formation of Paleocene age which consists of sandstone, siltstone, shale, coal beds, and locally impure limestone. A northeast-trending normal fault through the middle of the area, downthrown on the southeast side, has displaced the generally flat lying strata as much as 300 feet (91 m). Most of the minable coal lies northwest of this fault.

Effect of Colombian coal rank and its feeding technology on substitute natural gas production by entrained gasification

Directory of Open Access Journals (Sweden)

Juan Fernando Pérez-Bayer

2016-01-01

Full Text Available The effect of coal rank (from sub-bituminous to semi-anthracite and type of fuel feeding technology (slurry and dry on the production of substitute natural gas (SNG in entrained flow gasifiers is studied. Ten coals from important Colombian mines were selected. The process is modeled under thermochemical equilibrium using Aspen Plus, and its performance is evaluated in function of output parameters that include SNG heating value, Wobbe index, coal conversion efficiency, cold gas efficiency, process efficiency, global efficiency, and SNG production rate, among others. In descending order, the coal-to-SNG process improves energetically with the use of coals with: higher volatile-matter to fixed-carbon ratio, lower ash content, higher C+H/O ratio, and higher coal heating value. The overall energy efficiency of the slurry-feed technology (S-FT to produce SNG by gasification is 17% higher than the dry-feed technology (D-FT, possibly as a consequence of the higher CH4 concentration in the syngas (around 7 vol. % when the coal is fed as aqueous slurry. As the simulated SNG meets the natural gas (NG quality standards in Colombia, the substitute gaseous fuel could be directly transported through pipelines. Therefore, the coal-to-SNG process is a technically feasible and unconventional alternative for NG production.

Preparation and combustion of coal-water fuel from the Sin Pun coal deposit, southern Thailand

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-05-01

In response to an inquiry by the Department of Mineral Resources in Thailand, the Energy & Environmental Research Center (EERC) prepared a program to assess the responsiveness of Sin Pun lignite to the temperature and pressure conditions of hot-water drying. The results indicate that drying made several improvements in the coal, notably increases in heating value and carbon content and reductions in equilibrium moisture and oxygen content. The equilibrium moisture content decreased from 27 wt% for the raw coal to about 15 wt% for the hot-water-dried (HWD) coals. The energy density for a pumpable coal-water fuel (CWF) indicates an increase from 4500 to 6100 Btu/lb by hot-water drying. Approximately 650 lb of HWD Sin Pun CWF were fired in the EERC`s combustion test facility. The fuel burned extremely well, with no feed problems noted during the course of the test. Fouling and slagging deposits each indicated a very low rate of ash deposition, with only a dusty layer formed on the cooled metal surfaces. The combustor was operated at between 20% and 25% excess air, resulting in a flue gas SO{sub 2} concentration averaging approximately 6500 parts per million.

Bio-coal, torrefied lignocellulosic resources – Key properties for its use in co-firing with fossil coal – Their status

International Nuclear Information System (INIS)

Agar, D.; Wihersaari, M.

2012-01-01

Bio-coal has received generous amounts of media attention because it potentially allows greater biomass co-firing rates and net CO 2 emission reductions in pulverised-coal power plants. However, little scientific research has been published on the feasibility of full-scale commercial production of bio-coal. Despite this, several companies and research organisations worldwide have been developing patented bio-coal technologies. Are the expectations of bio-coal realistic and are they based on accepted scientific data? This paper examines strictly peer-reviewed scientific publications in order to find an answer. The findings to date on three key properties of torrefied biomass are presented and reviewed. These properties are: the mass and energy balance of torrefaction, the friability of the product and the equilibrium moisture content of torrefied biomass. It is these properties that will have a major influence on the feasibility of bio-coal production regardless of reactor technology employed in production. The presented results will be of use in modelling commercial production of bio-coal in terms of economics and green-house gas emission balance. -- Highlights: ► A technical note on torrefaction research results. ► Presents experimental values on three key properties. ► Mass-energy balance, grindability, equilibrium moisture content of torrefied biomass. ► Results useful for modelling bio-coal production schemes.

Refining and end use study of coal liquids I - pilot plant studies

Energy Technology Data Exchange (ETDEWEB)

Erwin, J.; Moulton, D.S.

1995-12-31

The Office of Fossil Energy, Pittsburgh Energy Technology Center is examining the ways in which coal liquids may best be integrated into the refinery of the 2000-2015 time frame and what performance and emission properties will prevail among the slate of fuels produced. The study consists of a Basic Program administered by Bechtel Group, Inc. to build a linear programming refinery model and provide processing and fuel properties data through subcontractors Southwest Research Institute, Amoco Oil R&D, and M.W. Kellogg Company. The model will be used in an Option 1 to devise a slate of test fuels meeting advanced specifications, which will be produced and tested for physical ASTM-type properties, engine performance, and vehicle emissions. Three coal liquids will be included: a direct liquid from bituminous coal, another from subbituminous, and a Fischer-Tropsch indirect liquefaction product. This paper reports the work to date on fractions of the first direct liquid including naphtha hydrotreating, heavy distillate hydrotreating, FCC of the heavy distillate hydrotreater products. Also reported are the first stages of work on the indirect liquefaction wax including feed preparation and FCC tests of blends with petroleum FCC feed.

The production of high load coal-water mixtures on the base of Kansk-Achinsk Coal Basin

Energy Technology Data Exchange (ETDEWEB)

Demidov, Y.; Bruer, G.; Kolesnikova, S. [Research and Design Institute for Problems of Development of Kansk-Achinsk Coal Basin (KATEKNilugol), Krasnoyarsk (Russian Federation)

1995-12-01

The results of the {open_quotes}KATEKNIIugol{close_quotes} work on the problems of high load coal-water mixtures are given in this article. General principles of the mixture production, short characteristics of Kansk-Achinsk coals, the experimental results of the coal mixture production on a test-industrial scale, the suspension preparation on the base of coal mixtures, technical-economical indexes of tested coal pipeline variants based on Kansk-Achinsk coals are described.

A biomimic thermal fabric with high moisture permeability

Directory of Open Access Journals (Sweden)

Fan Jie

2013-01-01

Full Text Available Moisture comfort is an essential factor for functional property of thermal cloth, especially for thick thermal cloth, since thick cloth may hinder effective moisture permeation, and high moisture concentration in the micro-climate between skin and fabric would cause cold feeling. Here, we report a biomimic thermal fabric with excellent warm retention and moisture management properties. In this fabric, the warp yarn system constructs many tree-shaped channel nets in the thickness direction of the fabric. Experimental result indicates that the special hierarchic configuration of warp yarns endows the biomimic thermal fabric with a better warm retention and water vapor management properties compared with the traditional fabrics.

Potassic zeolites from Brazilian coal ash for use as a fertilizer in agriculture.

Science.gov (United States)

Flores, Camila Gomes; Schneider, Helena; Marcilio, Nilson Romeu; Ferret, Lizete; Oliveira, João Carlos Pinto

2017-12-01

Brazilian coal has an ash content ranging from 30 to 50% by weight. Consequently, its use in coal-fired thermoelectric for power production generates a lot of waste. The construction sector is the largest consumer of coal ash, but it cannot absorb the entire amount generated. Thus, other applications for coal ash should be studied in aim to optimize the use of this industrial waste. This research had as focus to synthesize potassic zeolite from of the coal ash into on potassium fertilizer for the grown wheat plant. In this work, it was used a subbituminous coal from Mina do Leão (RS, Brazil) presenting 48.7% ash content on a dry basis. Concerning the synthesis of potassic zeolite, it was adopted the conventional method of hydrothermal treatment with potassium hydroxide. A schedule of experiments was conducted in order to define the optimum condition of zeolite synthesis that was then used an alkaline solution of 5M KOH with a reaction time of 24h at 150°C. According to this procedure, it was obtained a zeolite with a single crystalline phase, identified through X-ray diffraction as Merlinoite. Subsequently, it was performed a set of tests using potassic zeolite asa fertilizer for plants in a greenhouse. The synthesized potassic zeolite showed a good potential for its use as fertilizer in agriculture. Copyright © 2017 Elsevier Ltd. All rights reserved.

Determination of ultratrace levels of mercury in three SRMs by combustion RNAA

International Nuclear Information System (INIS)

Norman, B.R.; Becker, D.A.

2000-01-01

A radiochemical neutron activation analysis (RNAA) combustion method coupled with a neutron exposure normalization technique was used to determine low μg/kg mercury levels in three National Institute of Standards and Technology (NIST) Standard Reference Materials (SRMs). Two coals (sub-bituminous and bituminous) and a diet material were analyzed. The results obtained provided recommended values of approximately 5 μg/kg for SRM 1548a Typical Diet, 24 μg/kg for SRM 1635 Trace Elements in Coal (sub-bituminous), and 100 μg/kg for SRM 1632b Trace Elements in Coal (bituminous). (author)

Synfuels from low-rank coals at the Great Plains Gasification Plant

International Nuclear Information System (INIS)

Pollock, D.

1992-01-01

This presentation focuses on the use of low rank coals to form synfuels. A worldwide abundance of low rank coals exists. Large deposits in the United States are located in Texas and North Dakota. Low rank coal deposits are also found in Europe, India and Australia. Because of the high moisture content of lignite ranging from 30% to 60% or higher, it is usually utilized in mine mouth applications. Lignite is generally very reactive and contains varying amounts of ash and sulfur. Typical uses for lignite are listed. A commercial application using lignite as feedstock to a synfuels plant, Dakota Gasification Company's Great Plains Gasification Plant, is discussed

FY 1981 Report on the results of Sunshine Project. Coal energy; 1981 nendo sunshine keikaku seika hokokusho. Sekitan energy

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-07-01

This report presents the results of (researches on solvolysis liquefaction mechanisms and reaction promotion with oil- and coal-based solvents), conducted as part of the research and development project for coal liquefaction techniques. The FY 1981 program includes researches on (1) the effects of liquefaction reaction conditions on liquefaction yield and production of light products for coal species of low degree of carbonization, including brown coal, (2) the effects of pretreatment of coal on its liquefaction reactivity, and (3) up-grading of the solvolysis coal liquid (SCL). For the item (1), HA240 (hydrogenated Ashland's A240) is used to investigate its liquefaction capacity for various coal species of low degree of carbonization, including brown coal. For the item (2), the effects of pretreatment in a hot water bath with reflux was investigated for sub-bituminous coal in the FY 1980. In the FY 1981, various pretreatment methods are attempted for enhancing liquefaction reactivity of brown coal. As a result, it is found that ash content of brown coal is decreased to one-third of the initial level, when it is treated in a diluted hydrochloric acid bath with reflux. For the item (3), SCL hydrogenated by Birch reduction (B-SCL, 1) is compared with H-SCL with respect to properties, structures and thermal crackability, to discuss the items required for the catalyst to be used in the second stage by clarifying effectiveness of the catalyst. (NEDO)

Distinctive features of high-ash bituminuos coals combution with low milling fineness in furnace chambers with bottom blowing

Science.gov (United States)

Zroychikov, N. A.; Kaverin, A. A.; Biryukov, Ya A.

2017-11-01

Nowadays the problem of improvement of pulverized coal combustion schemes is an actual one for national power engineering, especially for combustion of coals with low milling fineness with significant portion of moisture or mineral impurities. In this case a big portion of inert material in the fuel may cause impairment of its ignition and combustion. In addition there are a lot of boiler installations on which nitrogen oxides emission exceeds standard values significantly. Decreasing of milling fineness is not without interest as a way of lowering an electric energy consumption for pulverization, which can reach 30% of power plant’s auxiliary consumption of electricity. Development of a combustion scheme meeting the requirements both for effective coal burning and environmental measures (related to NOx emission) is a complex task and demands compromising between these two factors, because implementation of NOx control by combustion very often leads to rising of carbon-in-ash loss. However widespread occurrence of such modern research technique as computer modeling allows to conduct big amount of variants calculations of combustion schemes with low cost and find an optimum. This paper presents results of numerical research of combined schemes of coal combustion with high portion of inert material based on straight-flow burners and nozzles. Several distinctive features of furnace aerodynamics, heat transfer and combustion has been found. The combined scheme of high-ash bituminouos coals combustion with low milling fineness, which allows effective combustion of pointed type of fuels with nitrogen oxides emission reduction has been proposed.

Study of the equilibrium of air-blown gasification of biomass to coal evolution fuels

International Nuclear Information System (INIS)

Biagini, Enrico

2016-01-01

Highlights: • Equilibrium model validated for coals, torrefied/green biomasses, in different gasifiers. • Maps of syngas composition, LHV and CGE for ER = 0–0.6, T = 500–2000 K, EBP = 0.004–0.158. • Effect of unconverted carbon, fuel moisture and overoxidation quantified. • Parameters for the maximum efficiency determined as functions of EBP. • EBP proven to be a good parameter for the quantitative comparison of different fuels. - Abstract: A non-stoichiometric equilibrium model based on the minimization of the Gibbs free energy was used to study the isothermal and adiabatic air-blown gasification of solid fuels on a carbonization curve from fossil (hard/brown coals, peat) to renewable (green biomasses and cellulose) fuels, including torrefied biofuels. The maps of syngas composition, heating value and process efficiency were provided as functions of equivalent ratio (oxygen-to-fuel ratio) in the range 0–0.6, temperature in 500–2000 K, and a fuel parameter, which allowed different cases to be quantitatively compared. The effect of fuel moisture, unconverted carbon and conditions to limit the tar formation was also studied. Cold gas efficiency >0.75 can be achieved for coals at high temperature, using entrained beds (which give low unconverted carbon), and improved by moisture/added steam. The bigger efficiency of green biomasses is only potential, as the practical limits (high temperature required to limit tar formation, moisture content and unconverted carbon in small gasifiers) strongly reduce the gasification performance. Torrefied biomasses (and plastics having an intermediate fuel parameter between coals and green biomasses) can attain high efficiency also in real conditions. The results shown in this work can be useful to evaluate the most promising feedstock (depending on its composition and possible pre-treatment/upgrading), define the operating conditions for maximizing the syngas heating value or the global efficiency, assess the

Prediction of coal response to froth flotation based on coal analysis using regression and artificial neural network

Energy Technology Data Exchange (ETDEWEB)

Jorjani, E.; Poorali, H.A.; Sam, A.; Chelgani, S.C.; Mesroghli, S.; Shayestehfar, M.R. [Islam Azad University, Tehran (Iran). Dept. of Mining Engineering

2009-10-15

In this paper, the combustible value (i.e. 100-Ash) and combustible recovery of coal flotation concentrate were predicted by regression and artificial neural network based on proximate and group macerals analysis. The regression method shows that the relationships between (a) in (ash), volatile matter and moisture (b) in (ash), in (liptinite), fusinite and vitrinite with combustible value can achieve the correlation coefficients (R{sup 2}) of 0.8 and 0.79, respectively. In addition, the input sets of (c) ash, volatile matter and moisture (d) ash, liptinite and fusinite can predict the combustible recovery with the correlation coefficients of 0.84 and 0.63, respectively. Feed-forward artificial neural network with 6-8-12-11-2-1 arrangement for moisture, ash and volatile matter input set was capable to estimate both combustible value and combustible recovery with correlation of 0.95. It was shown that the proposed neural network model could accurately reproduce all the effects of proximate and group macerals analysis on coal flotation system.

Co-pyrolysis of low rank coals and biomass: Product distributions

Energy Technology Data Exchange (ETDEWEB)

Soncini, Ryan M.; Means, Nicholas C.; Weiland, Nathan T.

2013-10-01

Pyrolysis and gasification of combined low rank coal and biomass feeds are the subject of much study in an effort to mitigate the production of green house gases from integrated gasification combined cycle (IGCC) systems. While co-feeding has the potential to reduce the net carbon footprint of commercial gasification operations, the effects of co-feeding on kinetics and product distributions requires study to ensure the success of this strategy. Southern yellow pine was pyrolyzed in a semi-batch type drop tube reactor with either Powder River Basin sub-bituminous coal or Mississippi lignite at several temperatures and feed ratios. Product gas composition of expected primary constituents (CO, CO{sub 2}, CH{sub 4}, H{sub 2}, H{sub 2}O, and C{sub 2}H{sub 4}) was determined by in-situ mass spectrometry while minor gaseous constituents were determined using a GC-MS. Product distributions are fit to linear functions of temperature, and quadratic functions of biomass fraction, for use in computational co-pyrolysis simulations. The results are shown to yield significant nonlinearities, particularly at higher temperatures and for lower ranked coals. The co-pyrolysis product distributions evolve more tar, and less char, CH{sub 4}, and C{sub 2}H{sub 4}, than an additive pyrolysis process would suggest. For lignite co-pyrolysis, CO and H{sub 2} production are also reduced. The data suggests that evolution of hydrogen from rapid pyrolysis of biomass prevents the crosslinking of fragmented aromatic structures during coal pyrolysis to produce tar, rather than secondary char and light gases. Finally, it is shown that, for the two coal types tested, co-pyrolysis synergies are more significant as coal rank decreases, likely because the initial structure in these coals contains larger pores and smaller clusters of aromatic structures which are more readily retained as tar in rapid co-pyrolysis.

Distribution of trace elements in selected pulverized coals as a function of particle size and density

Science.gov (United States)

Senior, C.L.; Zeng, T.; Che, J.; Ames, M.R.; Sarofim, A.F.; Olmez, I.; Huggins, Frank E.; Shah, N.; Huffman, G.P.; Kolker, A.; Mroczkowski, S.; Palmer, C.; Finkelman, R.

2000-01-01

Trace elements in coal have diverse modes of occurrence that will greatly influence their behavior in many coal utilization processes. Mode of occurrence is important in determining the partitioning during coal cleaning by conventional processes, the susceptibility to oxidation upon exposure to air, as well as the changes in physical properties upon heating. In this study, three complementary methods were used to determine the concentrations and chemical states of trace elements in pulverized samples of four US coals: Pittsburgh, Illinois No. 6, Elkhorn and Hazard, and Wyodak coals. Neutron Activation Analysis (NAA) was used to measure the absolute concentration of elements in the parent coals and in the size- and density-fractionated samples. Chemical leaching and X-ray absorption fine structure (XAFS) spectroscopy were used to provide information on the form of occurrence of an element in the parent coals. The composition differences between size-segregated coal samples of different density mainly reflect the large density difference between minerals, especially pyrite, and the organic portion of the coal. The heavy density fractions are therefore enriched in pyrite and the elements associated with pyrite, as also shown by the leaching and XAFS methods. Nearly all the As is associated with pyrite in the three bituminous coals studied. The sub-bituminous coal has a very low content of pyrite and arsenic; in this coal arsenic appears to be primarily organically associated. Selenium is mainly associated with pyrite in the bituminous coal samples. In two bituminous coal samples, zinc is mostly in the form of ZnS or associated with pyrite, whereas it appears to be associated with other minerals in the other two coals. Zinc is also the only trace element studied that is significantly more concentrated in the smaller (45 to 63 ??m) coal particles.

A LOW COST AND HIGH QUALITY SOLID FUEL FROM BIOMASS AND COAL FINES

Energy Technology Data Exchange (ETDEWEB)

John T. Kelly; George Miller; Mehdi Namazian

2001-07-01

Use of biomass wastes as fuels in existing boilers would reduce greenhouse gas emissions, SO2 and NOx emissions, while beneficially utilizing wastes. However, the use of biomass has been limited by its low energy content and density, high moisture content, inconsistent configuration and decay characteristics. If biomass is upgraded by conventional methods, the cost of the fuel becomes prohibitive. Altex has identified a process, called the Altex Fuel Pellet (AFP) process, that utilizes a mixture of biomass wastes, including municipal biosolids, and some coal fines, to produce a strong, high energy content, good burning and weather resistant fuel pellet, that is lower in cost than coal. This cost benefit is primarily derived from fees that are collected for accepting municipal biosolids. Besides low cost, the process is also flexible and can incorporate several biomass materials of interest The work reported on herein showed the technical and economic feasibility of the AFP process. Low-cost sawdust wood waste and light fractions of municipal wastes were selected as key biomass wastes to be combined with biosolids and coal fines to produce AFP pellets. The process combines steps of dewatering, pellet extrusion, drying and weatherizing. Prior to pilot-scale tests, bench-scale test equipment was used to produce limited quantities of pellets for characterization. These tests showed which pellet formulations had a high potential. Pilot-scale tests then showed that extremely robust pellets could be produced that have high energy content, good density and adequate weatherability. It was concluded that these pellets could be handled, stored and transported using equipment similar to that used for coal. Tests showed that AFP pellets have a high combustion rate when burned in a stoker type systems. While NOx emissions under stoker type firing conditions was high, a simple air staging approach reduced emissions to below that for coal. In pulverized-fuel-fired tests it was

Investigation of Coal-biomass Catalytic Gasification using Experiments, Reaction Kinetics and Computational Fluid Dynamics

Energy Technology Data Exchange (ETDEWEB)

Battaglia, Francine [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States); Agblevor, Foster [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States); Klein, Michael [Univ. of Delaware, Newark, DE (United States); Sheikhi, Reza [Northeastern Univ., Boston, MA (United States)

2015-12-31

A collaborative effort involving experiments, kinetic modeling, and computational fluid dynamics (CFD) was used to understand co-gasification of coal-biomass mixtures. The overall goal of the work was to determine the key reactive properties for coal-biomass mixed fuels. Sub-bituminous coal was mixed with biomass feedstocks to determine the fluidization and gasification characteristics of hybrid poplar wood, switchgrass and corn stover. It was found that corn stover and poplar wood were the best feedstocks to use with coal. The novel approach of this project was the use of a red mud catalyst to improve gasification and lower gasification temperatures. An important results was the reduction of agglomeration of the biomass using the catalyst. An outcome of this work was the characterization of the chemical kinetics and reaction mechanisms of the co-gasification fuels, and the development of a set of models that can be integrated into other modeling environments. The multiphase flow code, MFIX, was used to simulate and predict the hydrodynamics and co-gasification, and results were validated with the experiments. The reaction kinetics modeling was used to develop a smaller set of reactions for tractable CFD calculations that represented the experiments. Finally, an efficient tool was developed, MCHARS, and coupled with MFIX to efficiently simulate the complex reaction kinetics.

Effect of ultrafine iron and mineral matter on conversion of nitrogen and carbon during pyrolysis and gasification of coal

Energy Technology Data Exchange (ETDEWEB)

Ohtsuka, Y.; Furimsky, E. [Tohoku University, Sendai (Japan). Inst. for Chemical Reaction Science

1995-01-01

A subbituminous coal was used to determine the distribution of N{sub 2}, NH{sub 3}, and HCN during slow rate heating pyrolysis in He and gasification in 10% CO{sub 2} + He balance. During pyrolysis, the N{sub 2} was the major product followed by NH{sub 3} and HCN. During gasification, the N{sub 2} yields were significantly enhanced and those of NH{sub 3} and HCN decreased. Partial demineralization of coal resulted in a decrease in carbon and nitrogen conversion. This effect was also evident by comparing the nitrogen and carbon conversions of chars prepared at 500{degree}C from the fresh and demineralized coals. The addition of ultrafine Fe to coal increased conversion of carbon and nitrogen to N{sub 2} during gasification but had little effect during pyrolysis. Thus, during the former more than 80% of the coal nitrogen was released as N{sub 2}. Also, in the presence of Fe the temperature of N{sub 2} release was decreased by about 100{degree}C both during pyrolysis and gasification. During gasification of chars prepared at 1000{degree}C, the conversion of the coal nitrogen to N{sub 2} was much lower than that of carbon. 16 refs., 9 figs., 3 tabs.

Description of the operation and radiological impact of a spanish coastal coal-fired power station

International Nuclear Information System (INIS)

Corbacho, Jose A.; Baeza, Antonio; Robles, Beatriz; Mora, Juan C.; Cancio, David

2008-01-01

The 'Litoral' Coal-Fired Power Plant (LCFPP) is situated in the town of Carboneras (Almeria) in southern Spain. Its nominal output power is 1589 M We. The fuel used is imported sub-bituminous coal supplied by collier vessels, and unloaded in a port annexed to the plant. The climate of the area is semi-arid mediterranean, with particularly low rainfall. The plant's radiological impact was studied considering various exposure pathways for the workers and the general public. In particular, inhalation and external exposure contributions to the effective dose due to the different materials involved in the operation (coals, fly ash, and bottom ash) were evaluated. Alpha spectrometry was used to characterize radiologically the airborne particulates collected in aerosol filters at points within the installation, and to determine 210 Po levels in aerosols collected in filters placed around the power station. High resolution gamma spectrometry was used to characterize coal and ash samples from the plant, and soil samples collected outside the installation within a radius of 5 km. A dose rate monitor was used to measure the ambient dose equivalent at different points inside and outside the plant. Samples of the seawater used in the plant and of products for human consumption produced nearby were also collected and characterized radiologically. The effective dose was evaluated following a realistic approach based principally on experimental measurements and in situ observations, complemented with mathematical models when necessary. The resulting estimated effective doses for selected representative groups of workers and general public were all below the reference levels used in this work. (author)

Report on the bituminous coal liquefaction sub-committee in fiscal 1992; 1992 nendo rekiseitan ekika bukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This paper reports the activities of the bituminous coal liquefaction sub-committee in the Sunshine Project in fiscal 1992. With an intention of developing a technology on the process (NEDOL) suitable for liquefaction of wide range of coal types placing sub-bituminous coal at the center, researches were carried out by using a pilot plant, and engineering data purposed for practical application of the technology were acquired. The construction of the pilot plant was launched in fiscal 1991. It is necessary to execute the pilot plant plan steadily in the future, and at the same time, reliably acquire different data by means of supportive researches. Economic performance of the process is also important. The first sub-committee meeting presented the following agenda: the status of constructing the 150-t/d pilot plant, tests and investigations thereon, research works by using a 1-t/d PSU, development of the most suitable coal refining technology, development of a coal pretreatment technology, improvement of the distilled oil distribution, studies on coal liquefaction conditions, and studies on solvent hydrogenating catalysts. The second sub-committee meeting presented the following agenda: the status of constructing the pilot plant, tests and investigations on improving the performance of natural pylite catalyst and circulating solvent, technological investigations on structuring a liquefying reaction data analyzing system, studies using a 1-t/d PSU, development of the most suitable coal refining technology, studies on coal liquefaction conditions, and studies on solvent hydrogenating catalysts. (NEDO)

Petrography and rank of the Bhangtar coals, southeastern Bhutan

Energy Technology Data Exchange (ETDEWEB)

Pareek, H S [BH23, Meerut (India)

1990-07-01

In Bhutan, a potential coal deposit is exposed at Bhangtar in the 'landslide zone'. Nineteen coal seams are encountered in this area, and occur in the Lower Gondwana Supergroup preserved in between the Main Boundary Fault and the Thrust. The coal is low in moisture, {lt}1.76%, but the coal cores show moisture values of 3.16%. The ash content is up to 48.87% and increases substantially in the younger seams. The volatile content (on a pure coal basis) ranges from 23.38% to 41.02%. The sulphur content is less than 0.61%. The coals are non-coking. The amount of trace elements in the coal is quite low. The average petrographic composition of the Bhangtar coal is vitrinite - 31%, exinite - 2%, inertinite - 31%, and mineral and shaly matter - 36%, the vitrinite proportion decreases from the older to the younger seams, which are shaly. an age can be assigned to the Bhangtar coal. Based on oil reflectance, the rank of the coal is metalignitous to hypobituminous. The average microlithotype composition of the coal is vitrite - 30%, clarite - 1%, vitrinertite V - 14%, vitrinertite I - 11%, durite - 3%, fusite - 14%, and carbominerite - 27%. Vitrite decreases in proportion towards the younger seams, 'intermediates' show a concomitant increase, while durite and fusite remain constant. Carbonaceous shale contains fragmentary inertinite and vitrinite macerals and is interlayered with micro-bands of shaly coal which is characterised by abundant fragments of fusinite and vitrinite. The coal is very fragile and thus amenable to economic beneficiation. The coal is used as fuel in electric power plants. The Bhangtar coal is characteristically distinct from the Gondwana coals of India in petrography and rank, but correlates petrographically with the Kameng coals of Arunachal Pradesh, India. 18 refs., 4 figs., 8 tabs., 3 plates.

Atlas of the Colombian coal, Potential map and rank: Map 5-09; Atlas de los carbones colombianos. Mapa de potencial y rango: Plancha 5-09

Energy Technology Data Exchange (ETDEWEB)

Pulido Gonzalez, Orlando

1999-07-01

With the presentation of the Atlas of Coal to scale 1:500.000, it is sought to show to big features the location of the different areas with coal in Colombia, associating with the geologic units, the potential and the range. In the Map 5-09, the formations that include the coal are defined as Umir, Guaduas, Limbo, (Los Cuervos), San Fernando, (Carbonera), defined as Kst, Ksgt and Pgt. For the potential an arbitrary scale settled down, in the following way: in the first place bigger to 1000 million tons; between 1000 and 100; between 100 and 10 and lastly smaller to 10 million tons. These figures are represented in the map by triangles with colors that they are equal before to the figures mentioned. Keeping in mind the scale, it was opted to report the potential in the category of the hypothetical resources; when the resources or reserves are established, they are also reported. As for the range, in the map it is indicated by means of symbols that should be taken as a domain or tendency of the coal in each area in general. The the coal rank understood as the transformation that has reached along the geologic evolution is what is mentioned as anthracitic coal, semi-anthracitic, bituminous low in volatile, bituminous middle in volatile, bituminous high in volatile A, B and C, sub-bituminous and lastly the lignite. For each map are mentioned that there are determined.

30 CFR 870.18 - General rules for calculating excess moisture.

Science.gov (United States)

2010-07-01

... Collection of Coal Samples from Core; and, D1412-93, Standard Test Method for Equilibrium Moisture of Coal at... cautions: (a) You or your customer may do any test required by §§ 870.19 and 870.20. But whoever does a test, you are to keep test results and all related records for at least six years after the test date...

Permeability changes in coal resulting from gas desorption

Energy Technology Data Exchange (ETDEWEB)

Levine, J.R.; Johnson, P.W.

1992-11-30

This report documents studies on the effects of gas sorption on coal, with the intent of eventually evaluating how sorption and strain affect permeability. These studies were, carried out at the University of Alabama during the period from 1989 through 1992. Two major experimental methods were developed and used. In the strain experiments, electronic strain gauges were attached to polished blocks of coal in order to measure linear and volumetric swelling due to gas sorption. The effects of bedding plane orientation, of gas type, and of coal type were investigated. In the gravimetric experiment the weight of small samples of coal was measured during exposure to high pressure gases. Sample measurements were corrected for buoyancy effects and for sample swelling, and the results were plotted in the form of Langmuir isotherms. Experiments were conducted to determine the effect of grain size, coal type, moisture, and of sorbant gas. The advantage of this method is that it can be applied to very small samples, and it enabled comparison liptinite versus vitrinite concentrates, and kerogen rich versus kerogen depleted oil shales. Also included is a detailed discussion of the makeup of coal and its effect on gas sorption behavior.

Refining and end use study of coal liquids

International Nuclear Information System (INIS)

1998-01-01

Two direct coal liquids were evaluated by linear programming analysis to determine their value as petroleum refinery feedstock. The first liquid, DL1, was produced from bitiuminous coal using the Hydrocarbon Technologies, Inc.(HTI) two-stage hydrogenation process in Proof of Concept Run No.1, POC-1. The second liquid, DL2,was produced from sub-bituminous coal using a three-stage HTI process in Proof of Concept Run No. 2, POC-2; the third stage being a severe hydrogenation process. A linear programming (LP) model was developed which simulates a generic 150,000 barrel per day refinery in the Midwest U.S. Data from upgrading tests conducted on the coal liquids and related petroleum fractions in the pilot plant testing phase of the Refining and End Use Study was inputed into the model. The coal liquids were compared against a generic petroleum crude feedstock. under two scenarios. In the first scenario, it was assumed that the refinery capacity and product slate/volumes were fixed. The coal liquids would be used to replace a portion of the generic crude. The LP results showed that the DL1 material had essentially the same value as the generic crude. Due to its higher quality, the DL2 material had a value of approximately 0.60 $/barrel higher than the petroleum crude. In the second scenario, it was assumed that a market opportunity exists to increase production by one-third. This requires a refinery expansion. The feedstock for this scenario could be either 100% petroleum crude or a combination of petroleum crude and the direct coal liquids. Linear programming analysis showed that the capital cost of the refinery expansion was significantly less when coal liquids are utilized. In addition, the pilot plant testing showed that both of the direct coal liquids demonstrated superior catalytic cracking and naphtha reforming yields. Depending on the coal liquid flow rate, the value of the DL1 material was 2.5-4.0 $/barrel greater than the base petroleum crude, while the DL2

High rate spectroscopy for on-line nuclear coal analyzer (Nucoalyzer)

International Nuclear Information System (INIS)

McQuaid, J.H.; Brown, D.R.; Gozani, T.; Bozorgmanesh, H.

1980-01-01

A high count rate, time-variant Ge(Li) spectrometer has been developed for on-line coal analysis. The analyzer is being fabricated for use in a power generating station. Prompt neutron activation of coal samples is the basis of analysis, with 252 Cf as the source for irradiation. The spectroscopy system allows counting rates up to 150 k counts per second without significant loss in energy resolution or peak shape. The high data throughput allows the coal analyzer to be used for on-line process control. The coal analyzer will be discussed, with emphasis on the high-rate signal processing system. Results of analysis of coal samples will be presented

Highly Efficient Moisture-Triggered Nanogenerator Based on Graphene Quantum Dots.

Science.gov (United States)

Huang, Yaxin; Cheng, Huhu; Shi, Gaoquan; Qu, Liangti

2017-11-08

A high-performance moisture triggered nanogenerator is fabricated by using graphene quantum dots (GQDs) as the active material. GQDs are prepared by direct oxidation and etching of natural graphite powder, which have small sizes of 2-5 nm and abundant oxygen-containing functional groups. After the treatment by electrochemical polarization, the GQDs-based moisture triggered nanogenerator can deliver a high voltage up to 0.27 V under 70% relative humidity variation, and a power density of 1.86 mW cm -2 with an optimized load resistor. The latter value is much higher than the moisture-electric power generators reported previously. The GQD moisture triggered nanogenerator is promising for self-power electronics and miniature sensors.

Thermal maturity and organic composition of Pennsylvanian coals and carbonaceous shales, north-central Texas: Implications for coalbed gas potential

Energy Technology Data Exchange (ETDEWEB)

Hackley, Paul C. [U.S. Geological Survey, 956 National Center, Reston, VA 20192 (United States); Guevara, Edgar H.; Hentz, Tucker F. [Bureau of Economic Geology, The University of Texas at Austin, Austin, TX 78713 (United States); Hook, Robert W. [1301 Constant Springs Drive, Austin, TX 78746 (United States)

2009-01-31

Thermal maturity was determined for about 120 core, cuttings, and outcrop samples to investigate the potential for coalbed gas resources in Pennsylvanian strata of north-central Texas. Shallow (< 600 m; 2000 ft) coal and carbonaceous shale cuttings samples from the Middle-Upper Pennsylvanian Strawn, Canyon, and Cisco Groups in Archer and Young Counties on the Eastern Shelf of the Midland basin (northwest and downdip from the outcrop) yielded mean random vitrinite reflectance (R{sub o}) values between about 0.4 and 0.8%. This range of R{sub o} values indicates rank from subbituminous C to high volatile A bituminous in the shallow subsurface, which may be sufficient for early thermogenic gas generation. Near-surface (< 100 m; 300 ft) core and outcrop samples of coal from areas of historical underground coal mining in the region yielded similar R{sub o} values of 0.5 to 0.8%. Carbonaceous shale core samples of Lower Pennsylvanian strata (lower Atoka Group) from two deeper wells (samples from {proportional_to} 1650 m; 5400 ft) in Jack and western Wise Counties in the western part of the Fort Worth basin yielded higher R{sub o} values of about 1.0%. Pyrolysis and petrographic data for the lower Atoka samples indicate mixed Type II/Type III organic matter, suggesting generated hydrocarbons may be both gas- and oil-prone. In all other samples, organic material is dominated by Type III organic matter (vitrinite), indicating that generated hydrocarbons should be gas-prone. Individual coal beds are thin at outcrop (< 1 m; 3.3 ft), laterally discontinuous, and moderately high in ash yield and sulfur content. A possible analog for coalbed gas potential in the Pennsylvanian section of north-central Texas occurs on the northeast Oklahoma shelf and in the Cherokee basin of southeastern Kansas, where contemporaneous gas-producing coal beds are similar in thickness, quality, and rank. (author)

Fuel briquettes from brown coals of Yakutia

Energy Technology Data Exchange (ETDEWEB)

L.A. Nikolaeva; V.G. Latyshev; O.N. Burenina [Russian Academy of Sciences, Yakutsk (Russian Federation). Institute of Oil and Gas Problems

2009-04-15

Experimental data on the development of technology for the manufacture of briquetted fuel from brown coals with the use of various petroleum binders are presented. The influence of the moisture content, the coal particle-size composition, the binder type and concentration, the compacting pressure, and heat treatment regimes on the mechanical properties of the materials was studied. The optimal compositions and optimal values of the engineering parameters for the production of graded briquetted fuel from brown coals of the Kangalassy deposit in the Republic of Sakha (Yakutia) were established.

Electrokinetics and flocculation studies of coal

Energy Technology Data Exchange (ETDEWEB)

Dhawan, N. [Punjab Engineering College, Chandigarh (India). Dept. of Metallurgical Engineering

2008-07-01

Coal from India contains 25-35 per cent ash content. This leads to high slag volume, lower calorific value and inferior coke. In order to remove ash content, coal is washed, however, it retains some water that makes it difficult to process. Mechanical dewatering is performed in which a large portion of solids is removed while the remainder remains in centrifuge. There is therefore a need to recover solids and water. This paper discussed the use of flocculation and electrokinetic studies such as the determination of the point of zero charge. The experimental studies considered factors such as turbidity, faster settling, and compactness. Flocculation is brought about by the action of high molecular weight materials such as polyelectrolytes, where the material physically forms a bridge between two or more particles, uniting the sold particles into a random, three-dimensional structure, which is loose and porous. This paper also described the materials and methods of the electrokinetic studies on coal samples. Materials that were described included nephelometer, zeta meter, and a flocculator. It was concluded that in selecting the best flocculant, the preference order should be turbidity; settling rate; dosage; and moisture content. 3 refs., 2 tabs., 8 figs.

Multiple-heteroatom-containing sulfur compounds in a high sulfur coal

International Nuclear Information System (INIS)

Winans, R.E.; Neill, P.H.

1990-01-01

Flash vacuum pyrolysis of a high sulfur coal has been combined with high resolution mass spectrometry yielding information on aromatic sulfur compounds containing an additional heteroatom. Sulfur emission from coal utilization is a critical problem and in order to devise efficient methods for removing organic sulfur, it is important to know what types of molecules contain sulfur. A high sulfur Illinois No. 6 bituminous coal (Argonne Premium Coal Sample No. 3) was pyrolyzed on a platinum grid using a quartz probe inserted into a modified all glass heated inlet system and the products characterized by high resolution mass spectrometry (HRMS). A significant number of products were observed which contained both sulfur and an additional heteroatom. In some cases two additional heteroatoms were observed. These results are compared to those found in coal extracts and liquefaction products

The calculation of the chemical exergies of coal-based fuels by using the higher heating values

International Nuclear Information System (INIS)

Bilgen, Selcuk; Kaygusuz, Kamil

2008-01-01

This paper demonstrates the application of exergy to gain a better understanding of coal properties, especially chemical exergy and specific chemical exergy. In this study, a BASIC computer program was used to calculation of the chemical exergies of the coal-based fuels. Calculations showed that the chemical composition of the coal influences strongly the values of the chemical exergy. The exergy value of a coal is closely related to the H:C and O:C ratios. High proportions of hydrogen and/or oxygen, compared to carbon, generally reduce the exergy value of the coal. High contents of the moisture and/or the ash cause to low values of the chemical exergy. The aim of this paper is to calculate the chemical exergy of coals by using equations given in the literature and to detect and to evaluate quantitatively the effect of irreversible phenomena increased the thermodynamic imperfection of the processes. In this paper, the calculated exergy values of the fuels will be useful for energy experts studied in the coal mining area and coal-fired powerplants

Assessment of Coal Geology, Resources, and Reserves in the Gillette Coalfield, Powder River Basin, Wyoming

Science.gov (United States)

Luppens, James A.; Scott, David C.; Haacke, Jon E.; Osmonson, Lee M.; Rohrbacher, Timothy J.; Ellis, Margaret S.

2008-01-01

The Gillette coalfield, within the Powder River Basin in east-central Wyoming, is the most prolific coalfield in the United States. In 2006, production from the coalfield totaled over 431 million short tons of coal, which represented over 37 percent of the Nation's total yearly production. The Anderson and Canyon coal beds in the Gillette coalfield contain some of the largest deposits of low-sulfur subbituminous coal in the world. By utilizing the abundance of new data from recent coalbed methane development in the Powder River Basin, this study represents the most comprehensive evaluation of coal resources and reserves in the Gillette coalfield to date. Eleven coal beds were evaluated to determine the in-place coal resources. Six of the eleven coal beds were evaluated for reserve potential given current technology, economic factors, and restrictions to mining. These restrictions included the presence of railroads, a Federal interstate highway, cities, a gas plant, and alluvial valley floors. Other restrictions, such as thickness of overburden, thickness of coal beds, and areas of burned coal were also considered. The total original coal resource in the Gillette coalfield for all eleven coal beds assessed, and no restrictions applied, was calculated to be 201 billion short tons. Available coal resources, which are part of the original coal resource that is accessible for potential mine development after subtracting all restrictions, are about 164 billion short tons (81 percent of the original coal resource). Recoverable coal, which is the portion of available coal remaining after subtracting mining and processing losses, was determined for a stripping ratio of 10:1 or less. After mining and processing losses were subtracted, a total of 77 billion short tons of coal were calculated (48 percent of the original coal resource). Coal reserves are the portion of the recoverable coal that can be mined, processed, and marketed at a profit at the time of the economic

Proximate Analysis of Coal

Science.gov (United States)

Donahue, Craig J.; Rais, Elizabeth A.

2009-01-01

This lab experiment illustrates the use of thermogravimetric analysis (TGA) to perform proximate analysis on a series of coal samples of different rank. Peat and coke are also examined. A total of four exercises are described. These are dry exercises as students interpret previously recorded scans. The weight percent moisture, volatile matter,…

Effect of Water on Coal Strength | Singh | Momona Ethiopian Journal ...

African Journals Online (AJOL)

Water content is one of the most important factors influencing the rock strength. The present study has been conducted to see how coal strength changes under dry and water saturated conditions. The study reveals that the strength of coal decreases with increasing moisture. For rock mechanics and rock engineering ...

76 FR 68501 - Notice of Availability and Notice of Hearing for the Alton Coal Tract Coal Lease by Application...

Science.gov (United States)

2011-11-04

... Thermal Units per pound), 13 percent moisture, 10 percent ash, 39 percent volatile matter, 50 percent... coal and the time of production; 8. The percentage rate at which anticipated income streams should be...

EVALUATION OF BIOMASS AND COAL CO-GASIFICATION OF BRAZILIAN FEEDSTOCK USING A CHEMICAL EQUILIBRIUM MODEL

Directory of Open Access Journals (Sweden)

R. Rodrigues

Full Text Available Abstract Coal and biomass are energy sources with great potential for use in Brazil. Coal-biomass co-gasification enables the combination of the positive characteristics of each fuel, besides leading to a cleaner use of coal. The present study evaluates the potential of co-gasification of binary coal-biomass blends using sources widely available in Brazil. This analysis employs computational simulations using a reliable thermodynamic equilibrium model. Favorable operational conditions at high temperatures are determined in order to obtain gaseous products suitable for energy cogeneration and chemical synthesis. This study shows that blends with biomass ratios of 5% and equivalence ratios ≤ 0.3 lead to high cold gas efficiencies. Suitable gaseous products for chemical synthesis were identified at biomass ratios ≤ 35% and moisture contents ≥ 40%. Formation of undesirable nitrogen and sulfur compounds was also analyzed.

Volatility of coal liquids at high temperatures and pressures

Energy Technology Data Exchange (ETDEWEB)

Wilson, G M; Johnston, R H; Hwang, S C; Tsonopoulos, C

1981-01-01

The volatility of coal liquids has been experimentally determined at 700-880 F and about 2000 psia. These measurements were made in a flow apparatus to minimize thermal decomposition effects at high temperatures. Three coal liquids in mixture with Hat2, methane, and Hat2S were investigated. Measurements were also made up to 900 F on the vapor pressure of pure compounds found in coal liquids and on the equilibrium pressure of narrow coal liquid cuts. These data were used to develop a new method for the prediction of the critical point and the superatmospheric vapour pressures of aromatic fractions that is superior to the Maxwell-Bonnell correlation. The VLE data on coal liquids and some recent high-temperature VLE data on binaries of aromatics with Hat2 or methane were analyzed with a modified Chao-Seader correlation and a modified Redlich-Kwong equation of state. Both VLE correlations are shown to be equivalent in the prediction of the volatility of coal liquids, when the new vapour pressure procedure is used.

Coupling Effect of Intruding Water and Inherent Gas on Coal Strength Based on the Improved (Mohr-Coulomb Failure Criterion

Directory of Open Access Journals (Sweden)

Yiyu Lu

2016-11-01

Full Text Available When employing hydraulic processes to increase gas drainage efficiency in underground coal mines, coal seams become a three-phase medium, containing water intruding into the coal pores with the inherent occurrence of gas. This can change the stress state of the coal and cause instability. This work studied the mechanical properties of coal containing water and gas and derived an appropriate failure criterion. Based on mixture theory of unsaturated porous media, the effective stress of coal, considering the interaction of water and gas, was analyzed, and the failure criterion established by combining this with the Mohr–Coulomb criterion. By introducing the stress factor of matrix suction and using fitted curves of experimentally determined matrix suction and moisture content, the relationships between coal strength, gas pressure, and moisture content were determined. To verify the established strength theory, a series of triaxial compression strength tests of coal containing water and gas were carried out on samples taken from the Songzao, Pingdingshan, and Tashan mines in China. The experimental results correlated well with the theoretical predictions. The results showed a linear decrease in the peak strength of coal with increasing gas pressure and an exponential reduction in peak strength with increasing moisture content. The strength theory of coal containing water and gas can become an important part of multiphase medium damage theory.

FY 1981 Report on the results of Sunshine Project. Research and development of techniques for liquefaction of coal (Development of extraction type liquefaction plant using brown coal-based solvent and researches on milling at high temperature in oil); 1981 nendo sekitan ekika gijutsu no kenkyu kaihatsu, kattankei yozai chushutsu ekika plant no kaihatsu seika hokokusho. Koon yuchu funsai no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

This program is aimed at establishment of the techniques for milling of brown coal treated by primary dehydration and slurry adjustment, and secondary hydration plant, as part of the project for developing the techniques for liquefaction of brown coal. Brown coal (Australian Yallourn coal) treated by primary dehydration, solvents (creosote and decrystallized anthracene), and catalysts are used as the stock samples, to investigate the coal characteristics with respect to milling crushability, dehydration and liquefaction reactivity, and the slurries are prepared by changing coal charge rate, solvent and preparation temperature, to collect the data regarding, e.g., coal concentration, coal particle size, moisture level and liquefaction reactivity. It is found that milling crushability tends to decrease as coal charge rate or solvent/coal ratio increases whether creosote or decrystallized anthracene is used as the solvent. Milling crushability is unaffected by slurry preparation temperature. Content of residual moisture in the slurry decreases to 1% or less, when slurry preparation temperature is increased to 100 degrees C or higher. Liquefaction reactivity of the slurry shows slight dependence on slurry preparation temperature, when it is increased to 180 degrees C. (NEDO)

Influence of additives on the increase of the heating value of Bayah’s coal with upgrading brown coal (UBC) method

International Nuclear Information System (INIS)

Heriyanto, Heri; Widya Ernayati, K.; Umam, Chairul; Margareta, Nita

2015-01-01

UBC (upgrading brown coal) is a method of improving the quality of coal by using oil as an additive. Through processing in the oil media, not just the calories that increase, but there is also water repellent properties and a decrease in the tendency of spontaneous combustion of coal products produced. The results showed a decrease in the water levels of natural coal bayah reached 69%, increase in calorific value reached 21.2%. Increased caloric value and reduced water content caused by the water molecules on replacing seal the pores of coal by oil and atoms C on the oil that is bound to increase the percentage of coal carbon. As a result of this experiment is, the produced coal has better calorific value, the increasing of this new calorific value up to 23.8% with the additive waste lubricant, and the moisture content reduced up to 69.45%

Influence of additives on the increase of the heating value of Bayah’s coal with upgrading brown coal (UBC) method

Energy Technology Data Exchange (ETDEWEB)

Heriyanto, Heri [Chemical Engineering of University Sultan AgengTirtayasa, Indonesia Email: herfais@yahoo.com (Indonesia); Widya Ernayati, K.; Umam, Chairul; Margareta, Nita

2015-12-29

UBC (upgrading brown coal) is a method of improving the quality of coal by using oil as an additive. Through processing in the oil media, not just the calories that increase, but there is also water repellent properties and a decrease in the tendency of spontaneous combustion of coal products produced. The results showed a decrease in the water levels of natural coal bayah reached 69%, increase in calorific value reached 21.2%. Increased caloric value and reduced water content caused by the water molecules on replacing seal the pores of coal by oil and atoms C on the oil that is bound to increase the percentage of coal carbon. As a result of this experiment is, the produced coal has better calorific value, the increasing of this new calorific value up to 23.8% with the additive waste lubricant, and the moisture content reduced up to 69.45%.

Permeability changes in coal resulting from gas desorption. Final report

Energy Technology Data Exchange (ETDEWEB)

Levine, J.R.; Johnson, P.W.

1992-11-30

This report documents studies on the effects of gas sorption on coal, with the intent of eventually evaluating how sorption and strain affect permeability. These studies were, carried out at the University of Alabama during the period from 1989 through 1992. Two major experimental methods were developed and used. In the strain experiments, electronic strain gauges were attached to polished blocks of coal in order to measure linear and volumetric swelling due to gas sorption. The effects of bedding plane orientation, of gas type, and of coal type were investigated. In the gravimetric experiment the weight of small samples of coal was measured during exposure to high pressure gases. Sample measurements were corrected for buoyancy effects and for sample swelling, and the results were plotted in the form of Langmuir isotherms. Experiments were conducted to determine the effect of grain size, coal type, moisture, and of sorbant gas. The advantage of this method is that it can be applied to very small samples, and it enabled comparison liptinite versus vitrinite concentrates, and kerogen rich versus kerogen depleted oil shales. Also included is a detailed discussion of the makeup of coal and its effect on gas sorption behavior.

Electric Pulse Discharge Activated Carbon Supercapacitors for Transportation Application

Science.gov (United States)

Nayak, Subhadarshi; Agrawal, Jyoti

2012-03-01

ScienceTomorrow is developing a high-speed, low-cost process for synthesizing high-porosity electrodes for electrochemical double-layer capacitors. Four types of coal (lignite, subbituminous, bituminous, and anthracite) were used as precursor materials for spark discharge activation with multiscale porous structure. The final porosity and pore distribution depended, among other factors, on precursor type. The high gas content in low-grade carbon resulted in mechanical disintegration, whereas high capacitance was attained in higher-grade coal. The properties, including capacitance, mechanical robustness, and internal conductivity, were excellent when the cost is taken into consideration.

Coal-fired power plants and the causes of high temperature corrosion

Energy Technology Data Exchange (ETDEWEB)

Oakey, J E; Simms, N J [British Coal Corporation, Coal Technology Development Div., Cheltenham, Glos (United Kingdom); Tomkings, A B [ERA Technology Ltd., Leatherhead, Surrey (United Kingdom)

1996-12-01

The heat exchangers in all types of coal-fired power plant operate in aggressive, high temperature environments where high temperature corrosion can severely limit their service lives. The extent of this corrosion is governed by the combined effects of the operating conditions of the heat exchanger and the presence of corrosive species released from the coal during operation. This paper reviews the coal-related factors, such as ash deposition, which influence the operating environments of heat exchangers in three types of coal-fired power plant - conventional pulverized coal boilers, fluidized bed boilers and coal gasification systems. The effects on the performance of the materials used for these heat exchangers are then compared. (au) 35 refs.

Report on the FY 1993 basic survey for industrialization related to the survey of overseas geological structure (Muara Lakitan area, Indonesia). Tables and drawings; 1993 nendo kaigai chishitsu kozo nado chosa ni kakawaru kigyoka kiso chosa hokokusho (Indonesia Muara Lankin chiku). Hyo oyobi zumen

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

These are tables and drawings for the FY 1993 basic survey for the coal mine development/industrialization in the Muara Lakitan area of Indonesia. The geological structure in the survey area is under six sets of the anticline/syncline structure which have an NW-SE axis of fold, and exposes the Muaraenim seam repeatedly. The theoretical coal reserve in the depth down to 200m of each of the seams, Nos. 1, 2, 5, 12 and 13, which are great in coal seam change and exist relatively stably, is 143 million tons. The depth for adoption of the shovel/truck system open pit mining seems to be 50m or shallower, and the production is to be approximately 70 million tons. The coal is classified into a subbituminous coal-brown coal rank of the JIS classification. As tables, included were a table of the calculation of coal amount by seam and a table of the analytical result of coal by seam. As drawings, included were borehole logs of coal seam by boring, diagrams of thickness by seam such as the seam thickness/diagrams of thickness by seam such as the coal thickness, diagrams of range of calculating the coal amount, etc. Besides, in relation to coal properties, the report included value diagrams by seam of the inherent moisture, the ash, the volatile matter, the fixed carbon, the heating value, and the total sulfur content. (NEDO)

Gasification of high ash, high ash fusion temperature bituminous coals

Science.gov (United States)

Liu, Guohai; Vimalchand, Pannalal; Peng, WanWang

2015-11-13

This invention relates to gasification of high ash bituminous coals that have high ash fusion temperatures. The ash content can be in 15 to 45 weight percent range and ash fusion temperatures can be in 1150.degree. C. to 1500.degree. C. range as well as in excess of 1500.degree. C. In a preferred embodiment, such coals are dealt with a two stage gasification process--a relatively low temperature primary gasification step in a circulating fluidized bed transport gasifier followed by a high temperature partial oxidation step of residual char carbon and small quantities of tar. The system to process such coals further includes an internally circulating fluidized bed to effectively cool the high temperature syngas with the aid of an inert media and without the syngas contacting the heat transfer surfaces. A cyclone downstream of the syngas cooler, operating at relatively low temperatures, effectively reduces loading to a dust filtration unit. Nearly dust- and tar-free syngas for chemicals production or power generation and with over 90%, and preferably over about 98%, overall carbon conversion can be achieved with the preferred process, apparatus and methods outlined in this invention.

Coal gasification coal by steam using process heat from high-temperature nuclear reactors

International Nuclear Information System (INIS)

Heek, K.H. van; Juentgen, H.; Peters, W.

1982-01-01

This paper outlines the coal gasification process using a high-temperature nuclear reactor as a source of the process heat needed. Compared to conventional gasification processes coal is saved by 30-40%, coal-specific emissions are reduced and better economics of gas production are achieved. The introductory chapter deals with motives, aims and tasks of the development, followed by an explanation of the status of investigations, whereby especially the results of a semi-technical pilot plant operated by Bergbau-Forschung are given. Furthermore, construction details of a full-scale commercial gasifier are discussed, including the development of suitable alloys for the heat exchanger. Moreover problems of safety, licensing and economics of future plants have been investigated. (orig.) [de

Briquetting of coal fines and sawdust - effect of particle-size distribution

Energy Technology Data Exchange (ETDEWEB)

Patil, D.P.; Taulbee, D.; Parekh, B.K.; Honaker, R. [University of Kentucky, Lexington, KY (United States). Center for Applied Energy Research

2009-07-01

The coal industry usually discards fine-size (-150 microns) coal because of its high-moisture content and handling problems. One avenue for utilization is to either pelletize or briquette this material. However, industry has not adopted this route due in large part to significant drying and binder costs. In an effort to reduce these costs, compacting and briquetting studies were conducted to determine the effect of combining a coarse (1.18x0.15mm) spiral separator product with a fine coal flotation product (-150microns), with and without adding sawdust. Maximizing the packing density of the coal and wood waste mixture could potentially reduce the binder requirement by minimizing the void space as well as reducing shipping costs. Accordingly, work reported here focused on evaluating the impact of the particle-size distribution of different blends of fine and coarse coal, with and without sawdust and/or binder. The modified Proctor density of compacted blends along with the porosity and compressive strengths of briquettes made from each blend were determined. For the coal-only blends, the packing density was maximized by a relatively high (70% to 80%) coarse coal content. However, the packing density did not correlate with the compressive strength of the briquette that instead maximized with 100% fine flotation coal and continuously decreased as higher proportions of coarse coal were added. Similar compaction and compressive-strength results were obtained with mixtures of sawdust and varying proportions of coarse and fine coal. With the addition of a binder, the highest strengths were no longer obtained with 100% fine coal but instead maximized between 20% and 50% coarse coal addition depending on how long the briquettes were cured.

Possibilities of increasing coal charge density by adding fuel oil

Directory of Open Access Journals (Sweden)

M. Fröhlichová

2010-01-01

Full Text Available The requirement of all coke-making facilities is to achieve the highest possible production of high quality coke from a chamber. It can be achieved by filling the effective capacity of the chamber with the highest possible amount of coal. One of the possibilities of meeting this requirement is to increase the charge density in the coke chamber. In case of a coke battery operating on bulk coal there are many methods to increase the charge density including the use of wetting agents in the charge. This article presents the results of the laboratory experiments aiming at the increase of the charge density using fuel oil as a wetting agent. The experiments were carried out by means of the Pitin’s device using 3 coal charges with various granularity composition and moisture content of 7, 8, 9 and 10 %.

Preparation and Evaluation of Adsorbents from Coal and Irvingia gabonensis Seed Shell

Science.gov (United States)

Ezeokonkwo, Mercy A.; Ofor, Okechukwu F.; Ani, Julius U.

2017-12-01

The adsorption of Cd(II) and Pb(II) ions on adsorbents prepared from sub-bituminous coal, lignite and a blend of coal and Irvingia gabonensis seed shells was investigated. Fourier transform infrared, scanning electron microscope and X-ray fluorescence analyses implicated hydroxyl, carbonyl, Al2O3 and SiO2 as being responsible for binding the metal ions on the porous adsorbents. The optimum adsorption of carbonized lignite for the removal of Cd(II) and Pb(II) ions from aqueous media were 80.93% and 87.85%, respectively. Batch adsorption was done by effect of adsorbent dosage, pH, contact time, temperature, particle size, and initial concentration. Equilibrium for the removal of Pb(II) and Cd(II) was established within 100 and 120 min respectively. Blending the lignite-derived adsorbent with Irvingia gabonensis seed shell improved the performance significantly. More improvement was observed on modification of the blend using NaOH and H3PO4. Pb(II) was preferentially adsorbed than Cd(II) in all cases. Adsorption of Cd(II) and Pb(II) ions followed Langmuir isotherm. The kinetics of adsorption was best described by pseudo-second order model. The potential for using a blend of coal and agricultural byproduct (Irvingia gabonensis seed shell) was found to be a viable alternative for removal of toxic heavy metals from aqueous solutions.

CO-FIRING COAL, FEEDLOT, AND LITTER BIOMASS (CFB AND LFB) FUELS IN PULVERIZED FUEL AND FIXED BED BURNERS

International Nuclear Information System (INIS)

Kalyan Annamalai; John Sweeten; Saqib Mukhtar; Ben Thien; Gengsheng Wei; Soyuz Priyadarsan

2002-01-01

Intensive animal feeding operations create large amounts of animal waste that must be safely disposed of in order to avoid environmental degradation. Cattle feedlots and chicken houses are two examples. In feedlots, cattle are confined to small pens and fed a high calorie grain diet in preparation for slaughter. In chicken houses, thousands of chickens are kept in close proximity. In both of these operations, millions of tons of manure are produced every year. In this project a co-firing technology is proposed which would use manure that cannot be used for fertilizer, for power generation. Since the animal manure has economic uses as both a fertilizer and as a fuel, it is properly referred to as feedlot biomass (FB) for cow manure, or litter biomass (LB) for chicken manure. The biomass will be used a as a fuel by mixing it with coal in a 90:10 blend and firing it in existing coal fired combustion devices. This technique is known as co-firing, and the high temperatures produced by the coal will allow the biomass to be completely combusted. Therefore, it is the goal of the current research to develop an animal biomass cofiring technology. A cofiring technology is being developed by performing: (1) studies on fundamental fuel characteristics, (2) small scale boiler burner experiments, (3) gasifier experiments, (4) computer simulations, and (5) an economic analysis. The fundamental fuel studies reveal that biomass is not as high a quality fuel as coal. The biomass fuels are higher in ash, higher in moisture, higher in nitrogen and sulfur (which can cause air pollution), and lower in heat content than coal. Additionally, experiments indicate that the biomass fuels have higher gas content, release gases more readily than coal, and less homogeneous. Small-scale boiler experiments revealed that the biomass blends can be successfully fired, and NO(sub x) pollutant emissions produced will be similar to or lower than pollutant emissions when firing coal. This is a surprising

CO-FIRING COAL, FEEDLOT, AND LITTER BIOMASS (CFB AND LFB) FUELS IN PULVERIZED FUEL AND FIXED BED BURNERS

Energy Technology Data Exchange (ETDEWEB)

Kalyan Annamalai; John Sweeten; Saqib Mukhtar; Ben Thien; Gengsheng Wei; Soyuz Priyadarsan

2002-01-15

Intensive animal feeding operations create large amounts of animal waste that must be safely disposed of in order to avoid environmental degradation. Cattle feedlots and chicken houses are two examples. In feedlots, cattle are confined to small pens and fed a high calorie grain diet in preparation for slaughter. In chicken houses, thousands of chickens are kept in close proximity. In both of these operations, millions of tons of manure are produced every year. In this project a co-firing technology is proposed which would use manure that cannot be used for fertilizer, for power generation. Since the animal manure has economic uses as both a fertilizer and as a fuel, it is properly referred to as feedlot biomass (FB) for cow manure, or litter biomass (LB) for chicken manure. The biomass will be used a as a fuel by mixing it with coal in a 90:10 blend and firing it in existing coal fired combustion devices. This technique is known as co-firing, and the high temperatures produced by the coal will allow the biomass to be completely combusted. Therefore, it is the goal of the current research to develop an animal biomass cofiring technology. A cofiring technology is being developed by performing: (1) studies on fundamental fuel characteristics, (2) small scale boiler burner experiments, (3) gasifier experiments, (4) computer simulations, and (5) an economic analysis. The fundamental fuel studies reveal that biomass is not as high a quality fuel as coal. The biomass fuels are higher in ash, higher in moisture, higher in nitrogen and sulfur (which can cause air pollution), and lower in heat content than coal. Additionally, experiments indicate that the biomass fuels have higher gas content, release gases more readily than coal, and less homogeneous. Small-scale boiler experiments revealed that the biomass blends can be successfully fired, and NO{sub x} pollutant emissions produced will be similar to or lower than pollutant emissions when firing coal. This is a surprising

Active methods of mercury removal from flue gases.

Science.gov (United States)

Marczak, Marta; Budzyń, Stanisław; Szczurowski, Jakub; Kogut, Krzysztof; Burmistrz, Piotr

2018-03-23

Due to its adverse impact on health, as well as its global distribution, long atmospheric lifetime and propensity for deposition in the aquatic environment and in living tissue, the US Environmental Protection Agency (US EPA) has classified mercury and its compounds as a severe air quality threat. Such widespread presence of mercury in the environment originates from both natural and anthropogenic sources. Global anthropogenic emission of mercury is evaluated at 2000 Mg year -1 . According to the National Centre for Emissions Management (Pol. KOBiZE) report for 2014, Polish annual mercury emissions amount to approximately 10 Mg. Over 90% of mercury emissions in Poland originate from combustion of coal.The purpose of this paper was to understand mercury behaviour during sub-bituminous coal and lignite combustion for flue gas purification in terms of reduction of emissions by active methods. The average mercury content in Polish sub-bituminous coal and lignite was 103.7 and 443.5 μg kg -1 . The concentration of mercury in flue gases emitted into the atmosphere was 5.3 μg m -3 for sub-bituminous coal and 17.5 μg m -3 for lignite. The study analysed six low-cost sorbents with the average achieved efficiency of mercury removal from 30.6 to 92.9% for sub-bituminous coal and 22.8 to 80.3% for lignite combustion. Also, the effect of coke dust grain size was examined for mercury sorptive properties. The fine fraction of coke dust (CD) adsorbed within 243-277 μg Hg kg -1 , while the largest fraction at only 95 μg Hg kg -1 . The CD fraction physical oxidation of Hg in the flue gas, its effectiveness has increased twofold.

Mercury capture by selected Bulgarian fly ashes: Influence of coal rank and fly ash carbon pore structure on capture efficiency

Science.gov (United States)

Kostova, I.J.; Hower, J.C.; Mastalerz, Maria; Vassilev, S.V.

2011-01-01

Mercury capture by fly ash C was investigated at five lignite- and subbituminous-coal-burning Bulgarian power plants (Republika, Bobov Dol, Maritza East 2, Maritza East 3, and Sliven). Although the C content of the ashes is low, never exceeding 1.6%, the Hg capture on a unit C basis demonstrates that the low-rank-coal-derived fly ash carbons are more efficient in capturing Hg than fly ash carbons from bituminous-fired power plants. While some low-C and low-Hg fly ashes do not reveal any trends of Hg versus C, the 2nd and, in particular, the 3rd electrostatic precipitator (ESP) rows at the Republika power plant do have sufficient fly ash C range and experience flue gas sufficiently cool to capture measurable amounts of Hg. The Republika 3rd ESP row exhibits an increase in Hg with increasing C, as observed in other power plants, for example, in Kentucky power plants burning Appalachian-sourced bituminous coals. Mercury/C decreases with an increase in fly ash C, suggesting that some of the C is isolated from the flue gas stream and does not contribute to Hg capture. Mercury capture increases with an increase in Brunauer-Emmett-Teller (BET) surface area and micropore surface area. The differences in Hg capture between the Bulgarian plants burning low-rank coal and high volatile bituminous-fed Kentucky power plants suggests that the variations in C forms resulting from the combustion of the different ranks also influence the efficiency of Hg capture. ?? 2010 Elsevier Ltd.

Mercury capture by selected Bulgarian fly ashes: Influence of coal rank and fly ash carbon pore structure on capture efficiency

Energy Technology Data Exchange (ETDEWEB)

Kostova, I.J.; Hower, J.C.; Mastalerz, M.; Vassilev, S.V. [University of Kentucky, Lexington, KY (United States). Center of Applied Energy Research

2011-01-15

Mercury capture by fly ash C was investigated at five lignite- and subbituminous-coal-burning Bulgarian power plants (Republika, Bobov Dol, Maritza East 2, Maritza East 3, and Sliven). Although the C content of the ashes is low, never exceeding 1.6%, the Hg capture on a unit C basis demonstrates that the low-rank-coal-derived fly ash carbons are more efficient in capturing Hg than fly ash carbons from bituminous-fired power plants. While some low-C and low-Hg fly ashes do not reveal any trends of Hg versus C, the 2nd and, in particular, the 3rd electrostatic precipitator (ESP) rows at the Republika power plant do have sufficient fly ash C range and experience flue gas sufficiently cool to capture measurable amounts of Hg. The Republika 3rd ESP row exhibits an increase in Hg with increasing C, as observed in other power plants, for example, in Kentucky power plants burning Appalachian-sourced bituminous coals. Mercury/C decreases with an increase in fly ash C, suggesting that some of the C is isolated from the flue gas stream and does not contribute to Hg capture. Mercury capture increases with an increase in Brunauer-Emmett-Teller (BET) surface area and micropore surface area. The differences in Hg capture between the Bulgarian plants burning low-rank coal and high volatile bituminous-fed Kentucky power plants suggests that the variations in C forms resulting from the combustion of the different ranks also influence the efficiency of Hg capture.

Effects of microwave irradiation treatment on physicochemical characteristics of Chinese low-rank coals

International Nuclear Information System (INIS)

Ge, Lichao; Zhang, Yanwei; Wang, Zhihua; Zhou, Junhu; Cen, Kefa

2013-01-01

Highlights: • Typical Chinese lignites with various ranks are upgraded through microwave. • The pore distribution extends to micropore region, BET area and volume increase. • FTIR show the change of microstructure and improvement in coal rank after upgrading. • Upgraded coals exhibit weak combustion similar to Da Tong bituminous coal. • More evident effects are obtained for raw brown coal with relative lower rank. - Abstract: This study investigates the effects of microwave irradiation treatment on coal composition, pore structure, coal rank, function groups, and combustion characteristics of typical Chinese low-rank coals. Results showed that the upgrading process (microwave irradiation treatment) significantly reduced the coals’ inherent moisture, and increased their calorific value and fixed carbon content. It was also found that the upgrading process generated micropores and increased pore volume and surface area of the coals. Results on the oxygen/carbon ratio parameter indicated that the low-rank coals were upgraded to high-rank coals after the upgrading process, which is in agreement with the findings from Fourier transform infrared spectroscopy. Unstable components in the coal were converted into stable components during the upgrading process. Thermo-gravimetric analysis showed that the combustion processes of upgraded coals were delayed toward the high-temperature region, the ignition and burnout temperatures increased, and the comprehensive combustion parameter decreased. Compared with raw brown coals, the upgraded coals exhibited weak combustion characteristics similar to bituminous coal. The changes in physicochemical characteristics became more notable when processing temperature increased from 130 °C to 160 °C or the rank of raw brown coal was lower. Microwave irradiation treatment could be considered as an effective dewatering and upgrading process

Demonstration of Pressurizing Coal/Biomass Mixtures Using Posimetric Solids Pump Technology

Energy Technology Data Exchange (ETDEWEB)

Westendorf, Tiffany; Acharya, Harish; Cui, Zhe; Furman, Anthony; Giammattei, Mark; Rader, Jeff; Vazquez, Arturo

2012-12-31

This document is the Final Technical Report for a project supported by U.S. DOE NETL (Contract No. DE-FE0000507), GE Global Research, GE Energy, and Idaho National Laboratory (INL). This report discusses key project accomplishments for the period beginning August 7, 2009 and ending December 31, 2012. In this project, pressurized delivery of coal/biomass mixtures using GE Posimetric* solids pump technology was achieved in pilot scale experiments. Coal/biomass mixtures containing 10-50 wt% biomass were fed against pressures of 65-450 psi. Pressure capability increased with decreasing biomass content for a given pump design, and was linked to the interaction of highly compressible coal/biomass mixtures with the pump outlet design. Biomass pretreatment specifications for particle size and moisture content were defined based on bench-scale flowability, compressibility, friction, and permeability experiments that mimic the behavior of the Posimetric pump. A preliminary economic assessment of biomass pretreatment and pump operation for coal/biomass mixtures (CBMs) was conducted.

High pressure MHD coal combustors investigation, phase 2

Science.gov (United States)

Iwata, H.; Hamberg, R.

1981-05-01

A high pressure MHD coal combustor was investigated. The purpose was to acquire basic design and support engineering data through systematic combustion experiments at the 10 and 20 thermal megawatt size and to design a 50 MW/sub t/ combustor. This combustor is to produce an electrically conductive plasma generated by the direct combustion of pulverized coal with hot oxygen enriched vitiated air that is seeded with potassium carbonate. Vitiated air and oxygen are used as the oxidizer, however, preheated air will ultimately be used as the oxidizer in coal fired MHD combustors.

Unexpectedly high uptake of palladium by bituminous coals

Energy Technology Data Exchange (ETDEWEB)

Lakatos, J. [Research Lab. for Mining Chemistry, Hungarian Academy of Sciences, Miskolc-Egyetemvaros (Hungary); Brown, S.D.; Snape, C.E. [Univ. of Strathclyde, Dept. of Pure and Applied Chemistry, Glasgow (United Kingdom)

1997-12-31

The uptake of palladium as a conversion catalyst onto coals of different rank was investigated. Palladium fixation occurs by a different mode to that for alkaline earth and first row transition metals. Therefore, the dispersion of relatively high concentration of palladium by an ion sorption process is even possible for bituminous coals. (orig.)

Characterization of the impregnated iron based catalyst for direct coal liquefaction by EXAFS

International Nuclear Information System (INIS)

Yang Jianli; Zhun Jisheng; Liu Zhenyu; Zhong Bing

2002-01-01

Catalyst plays an important role in direct coal liquefaction (DCL). Iron catalysts are regarded as the most attractive catalysts for DCL. To maximize catalytic effect and minimize catalysts usage, ultra-fine size catalysts are preferred. The most effective catalysts are found to be those impregnated onto coal because of their high dispersion on coal surface and intimate contact with coal particles. Besides the physical size, chemical form of a catalyst or a catalyst precursor is also important in determination of DCL activity. The expended X-ray absorption fine structure spectroscopy technique were used in this study. It was shown that the catalysts tested are in nanomater range and have structure mainly in the form of γ-FeOOH and FeS, or possibly of Fe/O/S. The presence of γ-FeOOH can be attributed to the interaction between Fe and the oxygen containing groups of coal or oxygen from moisture

Strength and Compaction Analysis of Sand-Bentonite-Coal Ash Mixes

Science.gov (United States)

Sobti, Jaskiran; Singh, Sanjay Kumar

2017-08-01

This paper deals with the strength and compaction characteristics of sand-bentonite-coal ash mixes prepared by varying percentages of sand, bentonite and coal ash to be used in cutoff walls and as a liner or cover material in landfills. The maximum dry density (MDD) and optimum moisture content (OMC) of sand-bentonite mixes and sand-bentonite-coal ash mixes were determined by conducting the standard proctor test. Also, the strength and stiffness characteristics of soil mixes were furnished using unconfined compressive strength test. The results of the study reveal influence of varying percentages of coal ash and bentonite on the compaction characteristics of the sand-bentonite-coal ash mixes. Also, validation of a statistical analysis of the correlations between maximum dry density (MDD), optimum moisture content (OMC) and Specific Gravity (G) was done using the experimental results. The experimental results obtained for sand-bentonite, sand-bentonite-ash and coal ash-bentonite mixes very well satisfied the statistical relations between MDD, OMC and G with a maximum error in the estimate of MDD being within ±1 kN/m3. The coefficient of determination (R2) ranged from 0.95 to 0.967 in case of sand-bentonite-ash mixes. However, for sand-bentonite mixes, the R2 values are low and varied from 0.48 to 0.56.

Influence of the hydrothermal dewatering on the combustion characteristics of Chinese low-rank coals

International Nuclear Information System (INIS)

Ge, Lichao; Zhang, Yanwei; Xu, Chang; Wang, Zhihua; Zhou, Junhu; Cen, Kefa

2015-01-01

This study investigates the influence of hydrothermal dewatering performed at different temperatures on the combustion characteristics of Chinese low-rank coals with different coalification maturities. It was found that the upgrading process significantly decreased the inherent moisture and oxygen content, increased the calorific value and fixed carbon content, and promoted the damage of the hydrophilic oxygen functional groups. The results of oxygen/carbon atomic ratio indicated that the upgrading process converted the low-rank coals near to high-rank coals which can also be gained using the Fourier transform infrared spectroscopy. The thermogravimetric analysis showed that the combustion processes of upgraded coals were delayed toward the high temperature region, and the upgraded coals had higher ignition and burnout temperature. On the other hand, based on the higher average combustion rate and comprehensive combustion parameter, the upgraded coals performed better compared with raw brown coals and the Da Tong bituminous coal. In ignition segment, the activation energy increased after treatment but decreased in the combustion stage. The changes in coal compositions, microstructure, rank, and combustion characteristics were more notable as the temperature in hydrothermal dewatering increased from 250 to 300 °C or coals of lower ranks were used. - Highlights: • Typical Chinese lignites with various ranks are upgraded by hydrothermal dewatering. • Upgraded coals exhibit chemical compositions comparable with that of bituminous coal. • FTIR show the change of microstructure and improvement in coal rank after upgrading. • Upgraded coals exhibit difficulty in ignition but combust easily. • More evident effects are obtained for raw brown coal with relative lower rank.

PULSE COMBUSTOR DESIGN QUALIFICATION TEST AND CLEAN COAL FEEDSTOCK TEST - VOLUME I AND VOLUME II

Energy Technology Data Exchange (ETDEWEB)

Unknown

2002-02-08

For this Cooperative Agreement, the pulse heater module is the technology envelope for an indirectly heated steam reformer. The field of use of the steam reformer pursuant to this Cooperative Agreement with DOE is for the processing of sub-bituminous coals and lignite. The main focus is the mild gasification of such coals for the generation of both fuel gas and char--for the steel industry is the main focus. An alternate market application for the substitution of metallurgical coke is also presented. This project was devoted to qualification of a 253-tube pulse heater module. This module was designed, fabricated, installed, instrumented and tested in a fluidized bed test facility. Several test campaigns were conducted. This larger heater is a 3.5 times scale-up of the previous pulse heaters that had 72 tubes each. The smaller heater has been part of previous pilot field testing of the steam reformer at New Bern, North Carolina. The project also included collection and reduction of mild gasification process data from operation of the process development unit (PDU). The operation of the PDU was aimed at conditions required to produce char (and gas) for the Northshore Steel Operations. Northshore Steel supplied the coal for the process unit tests.

Survey on development of brown coal liquefaction techniques; Kattan ekika gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-09-01

Described herein are results of literature survey on brown coal liquefaction reactions and elementary techniques. Liquefaction of brown coal in the presence of CO and steam, or CO, H{sub 2} and steam has been investigated. It is not clear by the literature survey whether it is superior to the normal process which uses hydrogen. Brown coal contains moisture at high contents, and the drying techniques are necessary to be developed for its liquefaction. The future coal liquefaction plant will be much larger than the past one, and there are a number of problems to be solved, such as those involved in the designs of large-sized high-pressure slurry pumps, heat exchangers and preheaters. It is also necessary to develop the materials of and production techniques for large reactors which are serviceable under severe conditions. The solid-liquid separation for liquefaction products involves a number of the elementary techniques characteristic of coal liquefaction processes, and needs many technological developments. The one-stage brown coal liquefaction process is compared with the two-stage process for the secondary hydrogenation of SCR, but no clear conclusions are reached. (NEDO)

Variations in pore characteristics in high volatile bituminous coals: Implications for coal bed gas content

Science.gov (United States)

Mastalerz, Maria; Drobniak, A.; Strapoc, D.; Solano-Acosta, W.; Rupp, J.

2008-01-01

The Seelyville Coal Member of the Linton Formation (Pennsylvanian) in Indiana was studied to: 1) understand variations in pore characteristics within a coal seam at a single location and compare these variations with changes occurring between the same coal at different locations, 2) elaborate on the influence of mineral-matter and maceral composition on mesopore and micropore characteristics, and 3) discuss implications of these variations for coal bed gas content. The coal is high volatile bituminous rank with R0 ranging from 0.57% to 0.60%. BET specific surface areas (determined by nitrogen adsorption) of the coals samples studied range from 1.8 to 22.9??m2/g, BJH adsorption mesopore volumes from 0.0041 to 0.0339??cm3/g, and micropore volumes (determined by carbon dioxide adsorption) from 0.0315 to 0.0540??cm3/g. The coals that had the largest specific surface areas and largest mesopore volumes occur at the shallowest depths, whereas the smallest values for these two parameters occur in the deepest coals. Micropore volumes, in contrast, are not depth-dependent. In the coal samples examined for this study, mineral-matter content influenced both specific surface area as well as mesopore and micropore volumes. It is especially clear in the case of micropores, where an increase in mineral-matter content parallels the decrease of micropore volume of the coal. No obvious relationships were observed between the total vitrinite content and pore characteristics but, after splitting vitrinite into individual macerals, we see that collotelinite influences both meso- and micropore volume positively, whereas collodetrinite contributes to the reduction of mesopore and micropore volumes. There are large variations in gas content within a single coal at a single location. Because of this variability, the entire thickness of the coal must be desorbed in order to determine gas content reliably and to accurately calculate the level of gas saturation. ?? 2008 Elsevier B.V. All

BH5047 type depth sand moisture-meter of high sensitivity

International Nuclear Information System (INIS)

Ji Changsong; Xie Liangnian; Zhang Shulan; Zhang Shuheng

2000-01-01

A new depth neutron moisture meter BH5047 has been developed. BH5047 neutron moisture meter is characterised by it is high sensitivity and used for sand water content measurement at concrete mixer. Calibration function is obtained by the Method of Least Squares. Linear correlation efficiency is as good as 0.9977

Thermodynamic analysis and economic evaluation of a 1000 MW bituminous coal fired power plant incorporating low-temperature pre-drying (LTPD)

International Nuclear Information System (INIS)

Xu, Cheng; Xu, Gang; Zhu, Mingming; Dong, Wei; Zhang, Yang; Yang, Yongping; Zhang, Dongke

2016-01-01

Highlights: • An improved design of coal pre-drying using flue gas waste heat was proposed. • 0.4% energy efficiency increase was achieved with the proposed system. • The additional net economic benefit of the proposed system is $1.91 M per year. • Proposed concept can be widely applied to improve coal-fired power plant efficiency. - Abstract: Low-temperature pre-drying (LTPD) of lignite has been identified as an effective approach to improve the efficiency of lignite fired power plants. In this study, an improved concept for the pre-drying of medium moisture bituminous coals using flue gas waste heat was proposed and its feasibility was assessed. In the proposed configuration, the boiler exhaust flue gas is drawn to dryers to heat and pre-dry the raw coal, removing a large proportion of the coal moisture and leading to an improvement in the energy efficiency of the power plant. Thermodynamic analysis and economic evaluation were performed based on a typical 1000 MW bituminous coal fired power plant incorporating the proposed LTPD concept. The results showed that the net power plant efficiency gain is as much as 0.4 percentage point with additional net power output of 9.3 MW as compared to the reference plant without coal pre-drying. This was attributed to the reduction in the moisture content from 10.3 to 2.7 wt%. The additional net economic benefit attained due to the coal pre-drying was estimated to reach $1.91 M per year. This work provides a broadly applicable and economically feasible approach to further improve the energy efficiency of power plants firing coals with medium moisture contents.

Report on the bituminous coal liquefaction sub-committee in fiscal 1993; 1993 nendo rekiseitan ekika bukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

This paper reports the activities of the bituminous coal liquefaction sub-committee in fiscal 1993. With an intention of developing a technology on the process (NEDOL) suitable for liquefaction of wide range of coal types placing sub-bituminous coal at the center, researches were carried out by using a pilot plant, and engineering data purposed for practical application of the technology were acquired. The construction of the pilot plant, launched in fiscal 1991, will be performed under the operation research plan for efficient operation, based on the result of discussing the total project cost in fiscal 1992. The status of constructing the 150-t/d pilot plant in fiscal 1993 is in the phase of making the foundations subsequently from fiscal 1992, procurement of devices and construction materials, constructions of iron structures, installation, heat insulation, and painting, and building the central control building and piping facilities outside the battery limit. The paper also reports the tests and investigations on improving performance of natural pylite catalyst, the tests and investigations on improving performance of circulating solvent, and the technological investigations on structuring a liquefying reaction data analyzing system. For the supportive researches on the pilot plant, the paper describes studies by using a 1-t/d PSU, studies on coal liquefaction conditions, studies on synthesized iron sulfide catalysts, and studies on solvent hydrogenating catalysts. A comprehensive discussion was also given. (NEDO)

Differential pulmonary inflammation and in vitro cytotoxicity of size-fractionated fly ash particles from pulverized coal combustion

Energy Technology Data Exchange (ETDEWEB)

M. Ian Gilmour; Silvia O' Connor; Colin A.J. Dick; C. Andrew Miller; William P. Linak [U.S. Environmental Protection Agency, Research Triangle Park, NC (United States). National Health and Environmental Effects Research Laboratory

2004-03-01

Exposure to airborne particulate matter (PM) has been associated with adverse health effects in humans. Pulmonary inflammatory responses were examined in CD1 mice after intratracheal instillation of 25 or 100 {mu}g of ultrafine ({lt}0.2 {mu}m), fine ({lt}2.5 {mu}m), and coarse ({gt}2.5 {mu}m) coal fly ash from a combusted Montana subbituminous coal, and of fine and coarse fractions from a combusted western Kentucky bituminous coal. After 18 hr, the lungs were lavaged and the bronchoalveolar fluid was assessed for cellular influx, biochemical markers, and pro-inflammatory cytokines. The responses were compared with saline and endotoxin as negative and positive controls, respectively. On an equal mass basis, the ultrafine particles from combusted Montana coal induced a higher degree of neutrophil inflammation and cytokine levels than did the fine or coarse PM. The western Kentucky fine PM caused a moderate degree of inflammation and protein levels in bronchoalveolar fluid that were higher than the Montana fine PM. Coarse PM did not produce any significant effects. In vitro experiments with rat alveolar macrophages showed that of the particles tested, only the Montana ultrafine displayed significant cytotoxicity. It is concluded that fly ash toxicity is inversely related with particle size and is associated with increased sulfur and trace element content. 42 refs., 5 figs., 3 tabs.

Thermal Integration of CO{sub 2} Compression Processes with Coal-Fired Power Plants Equipped with Carbon Capture

Energy Technology Data Exchange (ETDEWEB)

Edward Levy

2012-06-29

Coal-fired power plants, equipped either with oxycombustion or post-combustion CO{sub 2} capture, will require a CO{sub 2} compression system to increase the pressure of the CO{sub 2} to the level needed for sequestration. Most analyses show that CO{sub 2} compression will have a significant effect on parasitic load, will be a major capital cost, and will contribute significantly to reduced unit efficiency. This project used first principle engineering analyses and computer simulations to determine the effects of utilizing compressor waste heat to improve power plant efficiency and increase net power output of coal-fired power plants with carbon capture. This was done for units with post combustion solvent-based CO{sub 2} capture systems and for oxyfired power plants, firing bituminous, PRB and lignite coals. The thermal integration opportunities analyzed for oxycombustion capture are use of compressor waste heat to reheat recirculated flue gas, preheat boiler feedwater and predry high-moisture coals prior to pulverizing the coal. Among the thermal integration opportunities analyzed for post combustion capture systems are use of compressor waste heat and heat recovered from the stripper condenser to regenerate post-combustion CO{sub 2} capture solvent, preheat boiler feedwater and predry high-moisture coals. The overall conclusion from the oxyfuel simulations is that thermal integration of compressor heat has the potential to improve net unit heat rate by up to 8.4 percent, but the actual magnitude of the improvement will depend on the type of heat sink used and to a lesser extent, compressor design and coal rank. The simulations of a unit with a MEA post combustion capture system showed that thermal integration of either compressor heat or stripper condenser heat to preheat boiler feedwater would result in heat rate improvements from 1.20 percent to 4.19 percent. The MEA capture simulations further showed that partial drying of low rank coals, done in combination

Coal-fired high performance power generating system. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-08-31

As a result of the investigations carried out during Phase 1 of the Engineering Development of Coal-Fired High-Performance Power Generation Systems (Combustion 2000), the UTRC-led Combustion 2000 Team is recommending the development of an advanced high performance power generation system (HIPPS) whose high efficiency and minimal pollutant emissions will enable the US to use its abundant coal resources to satisfy current and future demand for electric power. The high efficiency of the power plant, which is the key to minimizing the environmental impact of coal, can only be achieved using a modern gas turbine system. Minimization of emissions can be achieved by combustor design, and advanced air pollution control devices. The commercial plant design described herein is a combined cycle using either a frame-type gas turbine or an intercooled aeroderivative with clean air as the working fluid. The air is heated by a coal-fired high temperature advanced furnace (HITAF). The best performance from the cycle is achieved by using a modern aeroderivative gas turbine, such as the intercooled FT4000. A simplified schematic is shown. In the UTRC HIPPS, the conversion efficiency for the heavy frame gas turbine version will be 47.4% (HHV) compared to the approximately 35% that is achieved in conventional coal-fired plants. This cycle is based on a gas turbine operating at turbine inlet temperatures approaching 2,500 F. Using an aeroderivative type gas turbine, efficiencies of over 49% could be realized in advanced cycle configuration (Humid Air Turbine, or HAT). Performance of these power plants is given in a table.

XAS AND XPS CHARACTERIZATION OF MERCURY BINDING ON BROMINATED ACTIVATED CARBON

Science.gov (United States)

Brominated powdered activated carbon sorbents have been shown to e quite effective for mercury capture when injected into the flue gas duct at coal-fired power plants and are especially useful when buring Western low-chlorine subbituminous coals. X-ray absorption spectroscopy (X...

Coal-fired high performance power generating system

Energy Technology Data Exchange (ETDEWEB)

1992-07-01

The goals of the program are to develop a coal-fired high performance power generation system (HIPPS) by the year 2000 that is capable of > 47% thermal efficiency; NO[sub x] SO [sub x] and Particulates < 25% NSPS; Cost of electricity 10% lower; coal > 65% of heat input and all solid wastes benign. In order to achieve these goals our team has outlined a research plan based on an optimized analysis of a 250 MW[sub e] combined cycle system applicable to both frame type and aeroderivative gas turbines. Under the constraints of the cycle analysis we have designed a high temperature advanced furnace (HITAF) which integrates several combustor and air heater designs with appropriate ash management procedures. Most of this report discusses the details of work on these components, and the R D Plan for future work. The discussion of the combustor designs illustrates how detailed modeling can be an effective tool to estimate NO[sub x] production, minimum burnout lengths, combustion temperatures and even particulate impact on the combustor walls. When our model is applied to the long flame concept it indicates that fuel bound nitrogen will limit the range of coals that can use this approach. For high nitrogen coals a rapid mixing, rich-lean, deep staging combustor will be necessary. The air heater design has evolved into two segments: a convective heat exchanger downstream of the combustion process; a radiant panel heat exchanger, located in the combustor walls; The relative amount of heat transferred either radiatively or convectively will depend on the combustor type and the ash properties.

PULSE COMBUSTOR DESIGN QUALIFICATION TEST AND CLEAN COAL FEEDSTOCK TEST - VOLUME I AND VOLUME II; FINAL

International Nuclear Information System (INIS)

Unknown

2002-01-01

For this Cooperative Agreement, the pulse heater module is the technology envelope for an indirectly heated steam reformer. The field of use of the steam reformer pursuant to this Cooperative Agreement with DOE is for the processing of sub-bituminous coals and lignite. The main focus is the mild gasification of such coals for the generation of both fuel gas and char-for the steel industry is the main focus. An alternate market application for the substitution of metallurgical coke is also presented. This project was devoted to qualification of a 253-tube pulse heater module. This module was designed, fabricated, installed, instrumented and tested in a fluidized bed test facility. Several test campaigns were conducted. This larger heater is a 3.5 times scale-up of the previous pulse heaters that had 72 tubes each. The smaller heater has been part of previous pilot field testing of the steam reformer at New Bern, North Carolina. The project also included collection and reduction of mild gasification process data from operation of the process development unit (PDU). The operation of the PDU was aimed at conditions required to produce char (and gas) for the Northshore Steel Operations. Northshore Steel supplied the coal for the process unit tests

High-sulfur coal: tonnage and money at risk

International Nuclear Information System (INIS)

McMahan, R.L.; Knutson, K.S.

1991-01-01

More than 286 million tons of coal exceeds the Phase I standard i.e. 2.5 lb SO 2 per mmBtu, of the US Clean Air Act (1990). 85 mmtpy goes to currently scrubbed or unaffected (i.e. small) units. This leaves 201 mmtpy of high-sulphur coal at risk. 129 mmtpy of this is moving on a spot basis or is shipped under contracts that expire by 1995. This leaves about 72 mmtpy of captive and longterm contracts which many utility fuel buyers assume will be cancelled or renegotiated at a lower price. The legal position remains uncertain. However, the massive cancellation and/or renegotiation of existing contracts will have a tremendous economic impact on the coal industry. The resultant price change will in turn influence decisions to scrub or switch to low sulphur coals. 2 figs., 2 tabs

ULTRA LOW NOx INTEGRATED SYSTEM FOR NOx EMISSION CONTROL FROM COAL-FIRED BOILERS

Energy Technology Data Exchange (ETDEWEB)

Galen H. Richards; Charles Q. Maney; Richard W. Borio; Robert D. Lewis

2002-12-30

ALSTOM Power Inc.'s Power Plant Laboratories, working in concert with ALSTOM Power's Performance Projects Group, has teamed with the U.S. Department of Energy's National Energy Technology Laboratory (DOE NETL) to conduct a comprehensive study to develop/evaluate low-cost, efficient NOx control technologies for retrofit to pulverized coal fired utility boilers. The objective of this project was to develop retrofit NOx control technology to achieve less than 0.15 lb/MMBtu NOx (for bituminous coals) and 0.10 lb/MMBtu NOx (for subbituminous coals) from existing pulverized coal fired utility boilers at a cost which is at least 25% less than SCR technology. Efficient control of NOx is seen as an important, enabling step in keeping coal as a viable part of the national energy mix in this century, and beyond. Presently 57% of U.S. electrical generation is coal based, and the Energy Information Agency projects that coal will maintain a lead in U.S. power generation over all other fuel sources for decades (EIA 1998 Energy Forecast). Yet, coal-based power is being strongly challenged by society's ever-increasing desire for an improved environment and the resultant improvement in health and safety. The needs of the electric-utility industry are to improve environmental performance, while simultaneously improving overall plant economics. This means that emissions control technology is needed with very low capital and operating costs. This project has responded to the industry's need for low NOx emissions by evaluating ideas that can be adapted to present pulverized coal fired systems, be they conventional or low NOx firing systems. The TFS 2000{trademark} firing system has been the ALSTOM Power Inc. commercial offering producing the lowest NOx emission levels. In this project, the TFS 2000{trademark} firing system served as a basis for comparison to other low NOx systems evaluated and was the foundation upon which refinements were made to further

Steam coal processing technology: handling, high-order processing, COM, meth-coal

Energy Technology Data Exchange (ETDEWEB)

Kamata, H.; Onodera, J.

1982-01-01

Topics covered include: various handling techologies (overland and marine transport, storage, water removal, drying, comminution and sizing); various coal processing technologies (gravity concentration, magnetic separation, multi-stage flotation, liquid-phase pelletizing, chemical processing); production methods for coal-oil mixtures (COM), their physical properties, stability, storage, transport, advantages, plus recent trends in research and development; production of coal-methanol slurry (meth-coal), its stability, storage, transport, utilization and environmental problems, plus latest trends in research and development. (In Japanese)

Analysis of hard coal quality for narrow size fraction under 20 mm

Science.gov (United States)

Niedoba, Tomasz; Pięta, Paulina

2018-01-01

The paper presents the results of an analysis of hard coal quality diversion in narrow size fraction by using taxonomic methods. Raw material samples were collected in selected mines of Upper Silesian Industrial Region and they were classified according to the Polish classification as types 31, 34.2 and 35. Then, each size fraction was characterized in terms of the following properties: density, ash content, calorific content, volatile content, total sulfur content and analytical moisture. As a result of the analysis it can be stated that the best quality in the entire range of the tested size fractions was the 34.2 coking coal type. At the same time, in terms of price parameters, high quality of raw material characterised the following size fractions: 0-6.3 mm of 31 energetic coal type and 0-3.15 mm of 35 coking coal type. The methods of grouping (Ward's method) and agglomeration (k-means method) have shown that the size fraction below 10 mm was characterized by higher quality in all the analyzed hard coal types. However, the selected taxonomic methods do not make it possible to identify individual size fraction or hard coal types based on chosen parameters.

Baking and coking properties of hard coal under high pressure

Energy Technology Data Exchange (ETDEWEB)

Beyer, H.D.

1981-09-01

For a better assessment of the baking and coking properties of hard coal under high pressure as in modern coal beneficiation processes, the determination of the swelling index and the dilatation curve are investigated.

Automated mineralogical logging of coal and coal measure core

Energy Technology Data Exchange (ETDEWEB)

Stephen Fraser; Joan Esterle; Colin Ward; Ruth Henwood; Peter Mason; Jon Huntington; Phil Connor; Reneta Sliwa; Dave Coward; Lew Whitbourn [CSIRO Exploration & Mining (Australia)

2006-06-15

A mineralogical core logging system based on spectral reflectance (HyLogger{trademark}) has been used to detect and quantify mineralogies in coal and coal measure sediments. The HyLogger{trademark} system, as tested, operates in the visible-to-shortwave infrared spectral region, where iron oxides, sulphates, hydroxyl-bearing and carbonate minerals have characteristic spectral responses. Specialized software assists with mineral identification and data display. Three Phases of activity were undertaken. In Phase I, carbonates (siderite, ankerite, calcite) and clays (halloysite, dickite) were successfully detected and mapped in coal. Repeat measurements taken from one of the cores after three months demonstrated the reproducibility of the spectral approach, with some spectral differences being attributed to variations in moisture content and oxidation. Also, investigated was HyLogger{trademark} ability to create a 'brightness-profile' on coal materials, and these results were encouraging. In Phase II, geotechnically significant smectitic clays (montmorillonite) were detected and mapped in cores of clastic roof and floor materials. Such knowledge would be useful for mine planning and design purposes. In Phase III, our attempts at determining whether phosphorus-bearing minerals such as apatite could be spectrally detected were less than conclusive. A spectral index could only be created for apatite, and the relationships between the spectrally-derived apatite-index, the XRD results and the analytically-derived phosphorus measurements were ambiguous.

40 CFR 60.44Da - Standard for nitrogen oxides (NOX).

Science.gov (United States)

2010-07-01

... for heat input ng/J lb/MMBtu Gaseous fuels: Coal-derived fuels 210 0.50 All other fuels 86 0.20 Liquid fuels: Coal-derived fuels 210 0.50 Shale oil 210 0.50 All other fuels 130 0.30 Solid fuels: Coal-derived..., lignite not subject to the 340 ng/J heat input emission limit 2 260 0.60 Subbituminous coal 210 0.50...

Experimental study of rapid brown coal pyrolysis at high temperature

Energy Technology Data Exchange (ETDEWEB)

Qian, Lin; Sun, Shaozeng; Meng, Shun; Meng, Xianyu; Guo, Yangzhou [Harbin Institute of Technology, Harbin (China). Combustion Engineering Research Inst.

2013-07-01

Rapid coal pyrolysis is a very important step in the early stage of combustion. Rapid pyrolysis experiments of a brown coal at high temperature have been studied on a laminar drop tube furnace. The volatile mass release measured in this study is high for low rank coal. The activation energy and pre-exponential factor of pyrolysis are 19901.22 kJ/mol and 102.71, respectively. The nitrogen distribution between volatile and char is 0.54. With the increase of temperature, the yields of NH{sub 3} decreases, while those of HCN increases, leading the value of HCN/NH{sub 3} to become larger. At high temperature, the main nitrogen- containing species of pyrolysis in volatile is HCN.

Monitoring of qualitative characteristics of coal in mines and power plants

International Nuclear Information System (INIS)

Cervenka, M.; Krouzek, J.

1991-01-01

The basic qualitative characteristic of coal is its heating value, which is dependent on its noncombustible content and moisture. Sensors which have been developed for coal quality monitoring include two-channel radiometric ash meters, moisture meters and neutron sulfur analyzers. They are complemented with integrating balances and automated samplers and computer techniques. A complex quality monitoring system has been implemented in the North Bohemian localities of Vrsany and Most. The gamma ash meter is fitted with a scintillation counter. The measurement is continuous and contactless. A German ash meter equipped with a Geiger-Mueller tube is also mentioned. A continuous neutron analyzer is used for measuring the sulfur content; it is based on radiative capture of thermal neutrons. Described are also the method of coal weighing, the automated samplers, the central computer system and the software used. The results obtained with the systems implemented are summarized. The poor reliability of the Czechoslovak computer hardware poses problems. (M.D.). 7 figs., 6 tabs., 5 refs

High moisture airtight storage of barley and triticale: Effect of moisture level and grain processing on nitrogen and phosphorus solubility

DEFF Research Database (Denmark)

Ton Nu, Mai Anh; Blaabjerg, Karoline; Labouriau, Rodrigo

2015-01-01

The aim of this study was to evaluate the effect of storage time, grain processing (whole vs. rolled) and the combination of phytase, xylanase, β-glucanase and protease on nitrogen (N) and phosphorus (P) solubility during high moisture airtight (HMA) storage of barley and triticale at various...... moisture levels (20, 23, 26 and 29% moisture) and to compare HMA storage of cereals with dry storage for 49 days. Dry stored barley and triticale (10 and 13% moisture, respectively) were kept in 10 L plastic buckets for 0 and 49 days. HMA stored cereals were kept in airtight bags (400 g per bag) at 15 °C......) in HMA storage at 29% moisture to a greater extent compared with dry storage (P levels increased P solubility (rolled barley, whole and rolled triticale) and N solubility (whole and rolled triticale) linearly and decreased Phytate P:Total P (rolled barley) linearly...

Effect of moisture on the accuracy of coke-ash determination by X-ray backscattering

International Nuclear Information System (INIS)

Pandey, H.D.; Prasad, M.S.

1984-01-01

Effect of moisture on the rapid non-destructive estimation of ash content in coal specimens using the X-ray backscattering technique has been studied extensively by various workers. In the present work, an attempt has been made to estimate its influence when the technique is extended to coke-ash determinations. From the study of the variation of backscattered intensity with change in the moisture content of a coke specimen, it is observed that the ash content varies significantly at moisture levels higher than 5%. The variation, however, remains within allowable limits if the moisture level is kept below 5%. This observation is confirmed by the actual measurement of ash percentages in thirteen coke specimens containing three different states of moisture levels viz. (i) in the dry state, (ii) with 5% moisture and (iii) with 10% moisture. (author)

A system for incubations at high gas partial pressure

DEFF Research Database (Denmark)

Sauer, Patrick; Glombitza, Clemens; Kallmeyer, Jens

2012-01-01

dioxide sequestration. As an application of the system we extracted organic compounds from sub-bituminous coal using H2O as well as a H2O–CO2 mixture at elevated temperature (90°C) and pressure (5 MPa). Subsamples were taken at different time points during the incubation and analyzed by ion chromatography....... Furthermore we demonstrated the applicability of the system for studies of microbial activity, using samples from the Isis mud volcano. We could detect an increase in sulfate reduction rate upon the addition of methane to the sample....

Biogas production from various coal types using beef cattle rumen's liquid as a source of microorganisms consortium

Science.gov (United States)

Kurnani, Tubagus Benito Achmad; Harlia, Ellin; Hidayati, Yuli Astuti; Marlina, Eulis Tanti; Sugiarto, A. N.; Rahmah, K. N.; Joni, I. M.

2018-02-01

Nowadays, Indonesia is developing Coal-Bed Methane (CBM) production, but its production is not sufficient yet. Basically, CBM is produced naturally along with coal formation, i.e. through the activity of indigenous microorganisms. In this regard, to increase the production of CBM, adding a consortium of microorganisms into the coal deposit can be an option. One source of a consortium of bacteria available in nature is the rumen contents of ruminant livestock such as beef cattle. The purpose of this research was to know the capability of bacteria in rumen contents of beef cattle to produce CBM from various types of coal. In addition, to get a better concentration of bacteria than previous research so that it can be used as a reference for CBM production in the future. This explorative research used an experimental method with descriptive explanation. CBM production was performed using Hungate tube as a digester with three coal substrates, namely lignite, sub-bituminous and bituminous. This experiment also used 10-7 diluted rumen content of beef cattle as a source. The parameters measured were bacterial density, the amount of CBM, carbon dioxide and nitrous oxide on day 2, 5, 10 and 14. The treatment and parameters measurement were carried out in triplicates. This study finding showed that the highest bacterial density in all three types of coal was obtained on day 10 as well as the amount of CBM, carbon dioxide and nitrous oxide. These results are higher than the results from previous research therefore, this treatment can be used as an inoculant in a solid form for easy distribution.

Optimization of palm kernel shell torrefaction to produce energy densified bio-coal

International Nuclear Information System (INIS)

Asadullah, Mohammad; Adi, Ag Mohammad; Suhada, Nurul; Malek, Nur Hanina; Saringat, Muhammad Ilmam; Azdarpour, Amin

2014-01-01

Highlights: • Around 70% of bio-coal yield was achieved from PKS torrefaction at 300 °C. • The higher heating value of optimized bio-coal was 24.5 MJ/kg. • Around 94% of thermal yield was achieved with 70% mass yield. • The grindability of optimized bio-coal was comparable with coal. - Abstract: Biomass torrefaction is a thermal process, which is similar to a mild form of pyrolysis at temperatures ranging from 200 to 320 °C to produce energy densified solid fuel. The torrefied biomass is almost equivalent to coal and is termed as bio-coal. During torrefaction, highly volatile fraction of biomass including moisture and hemicellulose are released as vapors, providing energy enriched solid fuel, which is hydrophobic and brittle. In this study, bio-coal is produced from palm kernel shell (PKS) in a batch feeding reactor. The operating variables such as temperature, residence time and swiping gas flow rate are optimized. Around 73% yield of bio-coal with calorific value of 24.5 MJ/kg was achieved at optimum temperature 300 °C with residence time of 20 min and nitrogen gas flow rate of 300 mL/min. The thermal yield was calculated to be maximum of 94% for the bio-coal produced at 300 °C. The temperature and residence time of torrefaction are found to be the most sensitive parameters in terms of product yield, calorific value and thermal yield of bio-coal

Development of low rank coals upgrading and their CWM producing technology; Teihin`itan kaishitsu ni yoru CWM seizo gijutsu

Energy Technology Data Exchange (ETDEWEB)

Sugiyama, T [Center for Coal Utilization, Japan, Tokyo (Japan); Tsurui, M; Suto, Y; Asakura, M [JGC Corp., Tokyo (Japan); Ogawa, J; Yui, M; Takano, S [Japan COM Co. Ltd., Japan, Tokyo (Japan)

1996-09-01

A CWM manufacturing technology was developed by means of upgrading low rank coals. Even though some low rank coals have such advantages as low ash, low sulfur and high volatile matter content, many of them are merely used on a small scale in areas near the mine-mouths because of high moisture content, low calorification and high ignitability. Therefore, discussions were given on a coal fuel manufacturing technology by which coal will be irreversibly dehydrated with as much volatile matters as possible remaining in the coal, and the coal is made high-concentration CWM, thus the coal can be safely transported and stored. The technology uses a method to treat coal with hot water under high pressure and dry it with hot water. The method performs not only removal of water, but also irreversible dehydration without losing volatile matters by decomposing hydrophilic groups on surface and blocking micro pores with volatile matters in the coal (wax and tar). The upgrading effect was verified by processing coals in a pilot plant, which derived greater calorification and higher concentration CWM than with the conventional processes. A CWM combustion test proved lower NOx, lower SOx and higher combustion rate than for bituminous coal. The ash content was also found lower. This process suits a Texaco-type gasification furnace. For a production scale of three million tons a year, the production cost is lower by 2 yen per 10 {sup 3} kcal than for heavy oil with the same sulfur content. 11 figs., 15 tabs.

Neutron-capture gamma-ray analysis of coal for sulfur, iron, silicon and moisture

International Nuclear Information System (INIS)

Fay, D.A.

1979-05-01

Samples of coal weighing approximately 200 grams placed in a collimated beam of neutrons from the thermal column of the Ames Laboratory Research Reactor produced capture gamma-rays which could be used for the simultaneous determination of sulfur and iron. Spectra from NaI(Tl) and Ge(Li) detectors were used and interferences were located by examining spectra of the major elemental components of coal. In determining sulfur, iron is a potential source of interference when gamma-ray spectra are collected with a NaI(Tl) detector. Corrections for iron interference were made by use of a higher energy iron peak. The possibility of determining silicon in coal was investigated but this element determination was unsuccessful since capture gamma-ray spectrometry lacked the necessary sensitivity for silicon. A linear relation was found between the area of the hydrogen capture peak at 2.23 MeV and the amount of water added to coal

75 FR 17529 - High-Voltage Continuous Mining Machine Standard for Underground Coal Mines

Science.gov (United States)

2010-04-06

... High-Voltage Continuous Mining Machine Standard for Underground Coal Mines AGENCY: Mine Safety and... of high-voltage continuous mining machines in underground coal mines. It also revises MSHA's design...-- Underground Coal Mines III. Section-by-Section Analysis A. Part 18--Electric Motor-Driven Mine Equipment and...

Moisture conditions in buildings

DEFF Research Database (Denmark)

Rode, Carsten

2012-01-01

Growth of mould requires the presence of moisture at a certain high level. In a heated indoor environment such moisture levels occur only if there is a reason for the moisture supply. Such moisture can come from the use of the building, because of malfunctioning constructions, or it can be the re......Growth of mould requires the presence of moisture at a certain high level. In a heated indoor environment such moisture levels occur only if there is a reason for the moisture supply. Such moisture can come from the use of the building, because of malfunctioning constructions, or it can...

Biodesulphurisation of high sulphur coal by heap leaching

Energy Technology Data Exchange (ETDEWEB)

J. Cara; M.T. Carballo; A. Moran; D. Bonilla; O. Escolano; F.J. Garcia Frutos [Universidad de Leon, Leon (Spain). Departamento de Ingenieria Quimica

2005-10-01

The biodesulphurisation of coal carried out in pile could be an interesting option to clean coal. In view of the good results obtained in biodesulphurisation test column at lab scale on a sample of semianthracite coal that proceed of an industrial plant with a high sulphur content, mainly pyritic sulphur, the feasibility of the process at pilot plant scale was studied. The pile was formed with 6 ton of gravity middlings coal sample with a grain size -12+0.5 mm from S.A. Hullera Vasco-Leonesa industrial plant. The coal has a total sulphur content of 3.78% and a pyritic sulphur content of 2.88%, the rest of sulphur is organic sulphur. The biodesulphurisation process in pilot plant follows three stages: stabilization of the pile, biodesulphurisation and washing. Heap was sampled twice during stabilisation stage, at the end of desulphurisation process and finally once washed. A pyritic sulphur removal of 39% and total sulphur removal of 23% was obtained. To complete the bioleaching process, the treatment of purge of leachate was carried out with the objective to recycling to head of process. The best treatment was a pre-treatment of the leachate until pH 4, and further treatment by reverse osmosis of the clarified water. Comparing this process with conventional precipitation to reach disposal limits, the reagents consumption and sludges were reduced considerably and due to the high quality of permeate it permits to recycle it to head of process. 18 refs., 6 figs., 6 tabs.

ADVANCED MULTI-PRODUCT COAL UTILIZATION BY-PRODUCT PROCESSING PLANT

Energy Technology Data Exchange (ETDEWEB)

Robert Jewell; Thomas Robl; John Groppo

2005-03-01

The objective of the project is to build a multi-product ash beneficiation plant at Kentucky Utilities 2,200-MW Ghent Generating Station, located in Carroll County, Kentucky. This part of the study includes the examination of the feedstocks for the beneficiation plant. The ash, as produced by the plant, and that stored in the lower pond were examined. The ash produced by the plant was found to be highly variable as the plant consumes high and low sulfur bituminous coal, in Units 1 and 2 and a mixture of subbituminous and bituminous coal in Units 3 and 4. The ash produced reflected this consisting of an iron-rich ({approx}24%, Fe{sub 2}O{sub 3}), aluminum rich ({approx}29% Al{sub 2}O{sub 3}) and high calcium (6%-7%, CaO) ash, respectively. The LOI of the ash typically was in the range of 5.5% to 6.5%, but individual samples ranged from 1% to almost 9%. The lower pond at Ghent is a substantial body, covering more than 100 acres, with a volume that exceeds 200 million cubic feet. The sedimentation, stratigraphy and resource assessment of the in place ash was investigated with vibracoring and three-dimensional, computer-modeling techniques. Thirteen cores to depths reaching nearly 40 feet, were retrieved, logged in the field and transported to the lab for a series of analyses for particle size, loss on ignition, petrography, x-ray diffraction, and x-ray fluorescence. Collected data were processed using ArcViewGIS, Rockware, and Microsoft Excel to create three-dimensional, layered iso-grade maps, as well as stratigraphic columns and profiles, and reserve estimations. The ash in the pond was projected to exceed 7 million tons and contain over 1.5 million tons of coarse carbon, and 1.8 million tons of fine (<10 {micro}m) glassy pozzolanic material. The size, quality and consistency of the ponded material suggests that it is the better feedstock for the beneficiation plant.

On-stream analysis of coal by prompt neutron activation analysis

International Nuclear Information System (INIS)

Barker, D.

1981-01-01

The need for rapid continuous on-stream analysis of coal was recognised in 1975. Analytical systems capable of determining some of the most important compositional properties of coal have been developed. The research programme has produced a series of analysers suitable for on-stream, batch, slurry and laboratory analytical determination of coal. This series of analysers is marketed under the name of 'Nucoalyzer'. The Nucoalyzer - CONAC (Continuous On-line Nuclear Analyzer for Coal) offers real-time, continuous determination of calorific value, percentage ash, percentage moisture, percentage sulphur, boiler fouling and slagging indices. The CONAC model is described in this article. The analytical principle employed in the various Nucoalyzer systems is based on prompt neutron activation analysis

Studies of the fate of sulfur trioxide in coal-fired utility boilers based on modified selected condensation methods.

Science.gov (United States)

Cao, Yan; Zhou, Hongcang; Jiang, Wu; Chen, Chien-Wei; Pan, Wei-Ping

2010-05-01

The formation of sulfur trioxide (SO(3)) in coal-fired utility boilers can have negative effects on boiler performance and operation, such as fouling and corrosion of equipment, efficiency loss in the air preheater (APH), increase in stack opacity, and the formation of PM(2.5). Sulfur trioxide can also compete with mercury when bonding with injected activated carbons. Tests in a lab-scale reactor confirmed there are major interferences between fly ash and SO(3) during SO(3) sampling. A modified SO(3) procedure to maximize the elimination of measurement biases, based on the inertial-filter-sampling and the selective-condensation-collecting of SO(3), was applied in SO(3) tests in three full-scale utility boilers. For the two units burning bituminous coal, SO(3) levels starting at 20 to 25 ppmv at the inlet to the selective catalytic reduction (SCR), increased slightly across the SCR, owing to catalytic conversion of SO(2) to SO(3,) and then declined in other air pollutant control device (APCD) modules downstream to approximately 5 ppmv and 15 ppmv at the two sites, respectively. In the unit burning sub-bituminous coal, the much lower initial concentration of SO(3) estimated to be approximately 1.5 ppmv at the inlet to the SCR was reduced to about 0.8 ppmv across the SCR and to about 0.3 ppmv at the exit of the wet flue gas desulfurization (WFGD). The SO(3) removal efficiency across the WFGD scrubbers at the three sites was generally 35% or less. Reductions in SO(3) across either the APH or the dry electrostatic precipitator (ESP) in units burning high-sulfur bituminous coal were attributed to operating temperatures being below the dew point of SO(3).

Influence of Airflow on Laboratory Storage of High Moisture Corn Stover

Energy Technology Data Exchange (ETDEWEB)

Lynn M. Wendt; Ian J. Bonner; Amber N. Hoover; Rachel M. Emerson; William A. Smith

2014-04-01

Storing high moisture biomass for bioenergy use is a reality in many areas of the country where wet harvest conditions and environmental factors prevent dry storage from being feasible. Aerobic storage of high moisture biomass leads to microbial degradation and self-heating, but oxygen limitation can aid in material preservation. To understand the influence of oxygen presence on high moisture biomass (50 %, wet basis), three airflow rates were tested on corn stover stored in laboratory reactors. Temperature, carbon dioxide production, dry matter loss, chemical composition, fungal abundance, pH, and organic acids were used to monitor the effects of airflow on storage conditions. The results of this work indicate that oxygen availability impacts both the duration of self-heating and the severity of dry matter loss. High airflow systems experienced the greatest initial rates of loss but a shortened microbially active period that limited total dry matter loss (19 %). Intermediate airflow had improved preservation in short-term storage compared to high airflow systems but accumulated the greatest dry matter loss over time (up to 27 %) as a result of an extended microbially active period. Low airflow systems displayed the best performance with the lowest rates of loss and total loss (10 %) in storage at 50 days. Total structural sugar levels of the stored material were preserved, although glucan enrichment and xylan loss were documented in the high and intermediate flow conditions. By understanding the role of oxygen availability on biomass storage performance, the requirements for high moisture storage solutions may begin to be experimentally defined.

Experimental on moisture migration and pore pressure formation of concrete members subjected to high temperature

International Nuclear Information System (INIS)

Nagao, Kakuhiro; Nakane, Sunao

1993-01-01

The experimental studies concerning temperature, moisture migration, and pore pressure of mass concrete mock-up specimens heated up to high temperature at 110degC to 600degC, were performed, so as to correctly estimate the moisture migration behaviour of concrete members subjected to high temperature, which is considered significantly influenced on physical properties of concrete. As a results, it is confirmed that the moisture migration behavior of concrete members can be explained by temperature and pore pressure, and indicate the characteristics both sealed condition (dissipation of moisture is prevented) and unsealed condition (dissipation of moisture occur). (author)

Amenability of some Witbank bituminous ultra fine coals to binderless briquetting

CSIR Research Space (South Africa)

Mangena, SJ

2004-10-15

Full Text Available and briquetting Each of the Witbank ultra fine coals was air-dried and subsequently split into five homogeneous portions of 5 kg, respectively. Four portions from each sample were physically wetted to ca. 5%, 10%, 15% and 20% H2O, automatically mixed for 15 min... and long-distance haulage in uncovered trucks during the rainy season. In terms of compressive strength, the SJM1 coal studied was amenable to conventional binderless briquetting. 3.1.2. SJM2 coal The effect of moisture on the compressive strength...

Methane production from coal by a single methanogen

Science.gov (United States)

Sakata, S.; Mayumi, D.; Mochimaru, H.; Tamaki, H.; Yamamoto, K.; Yoshioka, H.; Suzuki, Y.; Kamagata, Y.

2017-12-01

Previous geochemical studies indicate that biogenic methane greatly contributes to the formation of coalbed methane (CBM). It is unclear, however, what part of coal is used for the methane production and what types of microbes mediate the process. Here we hypothesized that methylotrophic methanogens use methoxylated aromatic compounds (MACs) derived from lignin. We incubated 11 species of methanogens belonging to order Methanosarcinales with 7 types of MACs. Two strains of methanogens, i.e., Methermicoccus shengliensis AmaM and ZC-1, produced methane from the MACs. In fact, these methanogens used over 30 types of commercially available MACs in addition to methanol and methylamines. To date, it is widely believed that methanogens use very limited number of small compounds such as hydrogen plus carbon dioxide, acetate, and methanol, and only three methanogenic pathways are recognized accordingly. Here, in contrast, two Methermicoccus strains used many types of MACs. We therefore propose this "methoxydotrophic" process as the fourth methanogenic pathway. Incubation of AmaM with 2-methoxybenzoate resulted in methanogenesis associated with the stoichiometric production of 2-hydroxybenzoate. Incubation with 2-methoxy-[7-13C] benzoate and with [13C] bicarbonate indicated that two thirds of methane carbon derived from the methoxy group and one third from CO2. Furthermore, incubation with [2-13C] acetate resulted in significant increases of 13C in both methane and CO2. These results suggest the occurrence of O-demethylation, CO2 reduction and acetyl-CoA metabolism in the methoxydotrophic methanogenesis. Furthermore, incubation of AmaM with lignite, subbituminous or bituminous coals in the bicarbonate-buffered media revealed that AmaM produced methane directly from coals via the methoxydotrophic pathway. Although 4 types of MACs were detected in the coal media in addition to methanol and methylamines, their total concentrations were too low to account for the methane

Maximum solid concentrations of coal water slurries predicted by neural network models

Energy Technology Data Exchange (ETDEWEB)

Cheng, Jun; Li, Yanchang; Zhou, Junhu; Liu, Jianzhong; Cen, Kefa

2010-12-15

The nonlinear back-propagation (BP) neural network models were developed to predict the maximum solid concentration of coal water slurry (CWS) which is a substitute for oil fuel, based on physicochemical properties of 37 typical Chinese coals. The Levenberg-Marquardt algorithm was used to train five BP neural network models with different input factors. The data pretreatment method, learning rate and hidden neuron number were optimized by training models. It is found that the Hardgrove grindability index (HGI), moisture and coalification degree of parent coal are 3 indispensable factors for the prediction of CWS maximum solid concentration. Each BP neural network model gives a more accurate prediction result than the traditional polynomial regression equation. The BP neural network model with 3 input factors of HGI, moisture and oxygen/carbon ratio gives the smallest mean absolute error of 0.40%, which is much lower than that of 1.15% given by the traditional polynomial regression equation. (author)

Combustion and emissions characterization of pelletized coal fuels. Technical report, December 1, 1992--February 28, 1993

Energy Technology Data Exchange (ETDEWEB)

Rajan, S. [Southern Illinois Univ., Carbondale, IL (United States). Dept. of Mechanical Engineering and Energy Processes

1993-05-01

The aim of this project is to demonstrate that sorbent-containing coal pellets made from low grade coal or coal wastes are viable clean burning fuels, and to compare their performance with that of standard run-of-mine coal. Fuels to be investigated are: (a) carbonated pellets containing calcium hydroxide sorbent, (b) coal fines-limestone pellets with cornstarch as binder, (c) pellets made from preparation plant recovered coal containing limestone sorbent and gasification tar as binder, and (d) a standard run-of-mine Illinois seam coal. The fuels will be tested in a laboratory scale 411 diameter circulating fluidized bed combustor. Progress this quarter has centered on the development of a hydraulic press based pellet mill capable of the high compaction pressures necessary to produce the gasification tar containing pellets outlined in (c) above. Limited quantities of the pellets have been made, and the process is being fine tuned before proceeding into the production mode. Tests show that the moisture content of the coal is an important parameter that needs to be fixed within narrow limits for a given coal and binder combination to produce acceptable pellets. Combustion tests with these pellet fuels and the standard coal are scheduled for the next quarter.

Effects of moisture release and radiation properties in pulverized fuel combustion

DEFF Research Database (Denmark)

Yin, Chungen

2016-01-01

and impacts via a computational fluid dynamics (CFD) study of a 609 MWe pulverized coal-fired utility boiler. Overall speaking, it is suggested to add the free moisture in the fuel to the primary air stream while lump the bound moisture with volatiles in PF combustion modelling, although different methods.......g., oxy-fuel or air–fuel), account for the variations in CO2 and H2O concentrations in a flame, and include the impacts of other participating gases (e.g., CO and hydrocarbons) needs to be derived for combustion CFD community....

Long-Term Demonstration of Hydrogen Production from Coal at Elevated Temperatures Year 6 - Activity 1.12 - Development of a National Center for Hydrogen Technology

Energy Technology Data Exchange (ETDEWEB)

Stanislowski, Joshua; Tolbert, Scott; Curran, Tyler; Swanson, Michael

2012-04-30

The Energy & Environmental Research Center (EERC) has continued the work of the National Center for Hydrogen Technology® (NCHT®) Program Year 6 Task 1.12 project to expose hydrogen separation membranes to coal-derived syngas. In this follow-on project, the EERC has exposed two membranes to coal-derived syngas produced in the pilot-scale transport reactor development unit (TRDU). Western Research Institute (WRI), with funding from the State of Wyoming Clean Coal Technology Program and the North Dakota Industrial Commission, contracted with the EERC to conduct testing of WRI’s coal-upgrading/gasification technology for subbituminous and lignite coals in the EERC’s TRDU. This gasifier fires nominally 200–500 lb/hour of fuel and is the pilot-scale version of the full-scale gasifier currently being constructed in Kemper County, Mississippi. A slipstream of the syngas was used to demonstrate warm-gas cleanup and hydrogen separation using membrane technology. Two membranes were exposed to coal-derived syngas, and the impact of coal-derived impurities was evaluated. This report summarizes the performance of WRI’s patent-pending coalupgrading/ gasification technology in the EERC’s TRDU and presents the results of the warm-gas cleanup and hydrogen separation tests. Overall, the WRI coal-upgrading/gasification technology was shown to produce a syngas significantly lower in CO2 content and significantly higher in CO content than syngas produced from the raw fuels. Warm-gas cleanup technologies were shown to be capable of reducing sulfur in the syngas to 1 ppm. Each of the membranes tested was able to produce at least 2 lb/day of hydrogen from coal-derived syngas.

Assessment of coal geology, resources, and reserves in the Montana Powder River Basin

Science.gov (United States)

Haacke, Jon E.; Scott, David C.; Osmonson, Lee M.; Luppens, James A.; Pierce, Paul E.; Gunderson, Jay A.

2013-01-01

The purpose of this report is to summarize geology, coal resources, and coal reserves in the Montana Powder River Basin assessment area in southeastern Montana. This report represents the fourth assessment area within the Powder River Basin to be evaluated in the continuing U.S. Geological Survey regional coal assessment program. There are four active coal mines in the Montana Powder River Basin assessment area: the Spring Creek and Decker Mines, both near Decker; the Rosebud Mine, near Colstrip; and the Absaloka Mine, west of Colstrip. During 2011, coal production from these four mines totaled approximately 36 million short tons. A fifth mine, the Big Sky, had significant production from 1969-2003; however, it is no longer in production and has since been reclaimed. Total coal production from all five mines in the Montana Powder River Basin assessment area from 1968 to 2011 was approximately 1.4 billion short tons. The Rosebud/Knobloch coal bed near Colstrip and the Anderson, Dietz 2, and Dietz 3 coal beds near Decker contain the largest deposits of surface minable, low-sulfur, subbituminous coal currently being mined in the assessment area. A total of 26 coal beds were identified during this assessment, 18 of which were modeled and evaluated to determine in-place coal resources. The total original coal resource in the Montana Powder River Basin assessment area for the 18 coal beds assessed was calculated to be 215 billion short tons. Available coal resources, which are part of the original coal resource remaining after subtracting restrictions and areas of burned coal, are about 162 billion short tons. Restrictions included railroads, Federal interstate highways, urban areas, alluvial valley floors, state parks, national forests, and mined-out areas. It was determined that 10 of the 18 coal beds had sufficient areal extent and thickness to be evaluated for recoverable surface resources ([Roland (Baker), Smith, Anderson, Dietz 2, Dietz 3, Canyon, Werner

Experimental study of desulfurization of Zhong Liang Shau high sulfur coal by flotation

Energy Technology Data Exchange (ETDEWEB)

Jiang, Z.; Huang, B.; Cao, J. [China University of Mining and Technology (China). Beijing Graduate School

1994-12-01

Emission of large amount of SO{sub 2} from combustion of high sulfur coal causes serious environmental pollution. Pre-combustion desulfurization of high sulfur coal has become a necessity. This paper reports test results of fine coal desulfurization with different flotation technology and the effect of pyrite depressant. Test work showed that when the coal sample from Zhong Liang Shau was processed with a Free Jet Flotation Column its pyritic sulfur content was reduced from 3.08% to 0.84%, with 72.22% recovery of combustible matter in clean coal. The concept of Desulfurization Efficiency Index E{sub ds} for comprehensive evaluation of desulfurization process is proposed, which is defined as the product of the ratio of sulfur content reduction of clean coal and the recovery of combustible matters. 6 refs., 4 figs., 3 tabs.

Catalyst dispersion and activity under conditions of temperature-staged liquefaction

Energy Technology Data Exchange (ETDEWEB)

Davis, A.; Schobert, H.H.; Mitchell, G.D.; Artok, L.

1993-02-01

This research program involves the investigation of the use of highly dispersed catalyst precursors for the pretreatment of coals by mild hydrogenation. During the course of this effort solvent preswelling of the coal was evaluated as a means of deeply impregnating catalysts into coal, active phases of catalysts under reaction conditions were studied and the impact of these techniques were evaluated during pretreatment and temperature-staged liquefaction. Two coals, a Texas subbituminous and a Utah high volatile A bituminous, were used to examine the effects of solvent swelling pretreatment and catalyst impregnation on conversion behavior at 275[degrees]C, representative of the first, low-temperature stage in a temperature-staged liquefaction reaction. Ferrous sulfate, iron pentacarbonyl, ammonium tetrathiomolybdate, and molybdenum hexacarbonyl were used as catalyst precursors. Without swelling pretreatment, impregnation of both coals increased conversion, mainly through increased yields of preasphaltenes.

Catalyst dispersion and activity under conditions of temperature-staged liquefaction. Final report

Energy Technology Data Exchange (ETDEWEB)

Davis, A.; Schobert, H.H.; Mitchell, G.D.; Artok, L.

1993-02-01

This research program involves the investigation of the use of highly dispersed catalyst precursors for the pretreatment of coals by mild hydrogenation. During the course of this effort solvent preswelling of the coal was evaluated as a means of deeply impregnating catalysts into coal, active phases of catalysts under reaction conditions were studied and the impact of these techniques were evaluated during pretreatment and temperature-staged liquefaction. Two coals, a Texas subbituminous and a Utah high volatile A bituminous, were used to examine the effects of solvent swelling pretreatment and catalyst impregnation on conversion behavior at 275{degrees}C, representative of the first, low-temperature stage in a temperature-staged liquefaction reaction. Ferrous sulfate, iron pentacarbonyl, ammonium tetrathiomolybdate, and molybdenum hexacarbonyl were used as catalyst precursors. Without swelling pretreatment, impregnation of both coals increased conversion, mainly through increased yields of preasphaltenes.

Nanometre-sized pores in coal: Variations between coal basins and coal origin

Science.gov (United States)

Sakurovs, Richard; Koval, Lukas; Grigore, Mihaela; Sokolava, Anna; Ruppert, Leslie F.; Melnichenko, Yuri B.

2018-01-01

We have used small angle neutron scattering (SANS) to investigate the differences in methane and hexane penetration in pores in bituminous coal samples from the U.S., Canada, South Africa, and China, and maceral concentrates from Australian coals. This work is an extension of previous work that showed consistent differences between the extent of penetration by methane into 10–20 nm size pores in inertinite in bituminous coals from Australia, North America and Poland.In this study we have confirmed that there are differences in the response of inertinite to methane and hexane penetration in coals sourced from different coal basins. Inertinite in Permian Australian coals generally has relatively high numbers of pores in the 2.5–250 nm size range and the pores are highly penetrable by methane and hexane; coals sourced from Western Canada had similar penetrability to these Australian coals. However, the penetrability of methane and hexane into inertinite from the Australian Illawarra Coal Measures (also Permian) is substantially less than that of the other Australian coals; there are about 80% fewer 12 nm pores in Illawarra inertinite compared to the other Australian coals examined. The inertinite in coals sourced from South Africa and China had accessibility intermediate between the Illawarra coals and the other Australian coals.The extent of hexane penetration was 10–20% less than CD4 penetration into the same coal and this difference was most pronounced in the 5–50 nm pore size range. Hexane and methane penetrability into the coals showed similar trends with inertinite content.The observed variations in inertinite porosity between coals from different coal regions and coal basins may explain why previous studies differ in their observations of the relationships between gas sorption behavior, permeability, porosity, and maceral composition. These variations are not simply a demarcation between Northern and Southern Hemisphere coals.

A novel solar energy integrated low-rank coal fired power generation using coal pre-drying and an absorption heat pump

International Nuclear Information System (INIS)

Xu, Cheng; Bai, Pu; Xin, Tuantuan; Hu, Yue; Xu, Gang; Yang, Yongping

2017-01-01

Highlights: •An improved solar energy integrated LRC fired power generation is proposed. •High efficient and economic feasible solar energy conversion is achieved. •Cold-end losses of the boiler and condenser are reduced. •The energy and exergy efficiencies of the overall system are improved. -- Abstract: A novel solar energy integrated low-rank coal (LRC) fired power generation using coal pre-drying and an absorption heat pump (AHP) was proposed. The proposed integrated system efficiently utilizes the solar energy collected from the parabolic trough to drive the AHP to absorb the low-grade waste heat of the steam cycle, achieving larger amount of heat with suitable temperature for coal’s moisture removal prior to the furnace. Through employing the proposed system, the solar energy could be partially converted into the high-grade coal’s heating value and the cold-end losses of the boiler and the steam cycle could be reduced simultaneously, leading to a high-efficient solar energy conversion together with a preferable overall thermal efficiency of the power generation. The results of the detailed thermodynamic and economic analyses showed that, using the proposed integrated concept in a typical 600 MW LRC-fired power plant could reduce the raw coal consumption by 4.6 kg/s with overall energy and exergy efficiencies improvement of 1.2 and 1.8 percentage points, respectively, as 73.0 MW th solar thermal energy was introduced. The cost of the solar generated electric power could be as low as $0.044/kW h. This work provides an improved concept to further advance the solar energy conversion and utilisation in solar-hybrid coal-fired power generation.

Binderless briquetting of some selected South African prime coking, blend coking and weathered bituminous coals and the effect of coal properties on binderless briquetting

Energy Technology Data Exchange (ETDEWEB)

Mangena, S.J. [Division of Mining Technology, CSIR, PO Box 395, Pretoria, 0001 (South Africa); du Cann, V.M. [Coal and Mineral Technologies (Pty) Ltd, SABS, PO Box 73656, Lynnwood Ridge, Pretoria, 0040 (South Africa)

2007-07-02

The binderless briquetting of some selected South African prime coking and blend coking coals, as well as the effects of weathering on the binderless briquetting of some inertinite-rich bituminous coals, were investigated in the laboratory. Selected properties of these coals were determined and the coals were briquetted at various moisture contents and pressures. Based on the results obtained in this study, binderless briquetting was found to be most successful in the cases of the fresh, vitrinite-rich coking and blend coking coals and satisfactory in the fresh inertinite-rich Witbank coals. However, the bonding process seemed to be adversely affected by weathering. The negative impact on bonding could be ameliorated to some extent by the presence of a significant kaolinite content when the percentage ash reports in the order of more than 15% (air-dry basis). It should, however, be noted that kaolinite may reduce the water resistance of the briquettes. (author)

Experimental investigations on drying behaviour of Bulgarian brown coal in steam fluidized bed

International Nuclear Information System (INIS)

Buschsieweke, F.; Koenig, J.

1999-01-01

The main targets were: to investigate the parameters for optimizing the drying process as steam pressure, fluidization velocity and particle size; to identify the cost of drying and combustion processes considering the necessity of milling the coal (raw or dried). Test series with Bulgarian brown coal from Maritsa-East has been made. Two fractions with different particle size was got: A from 0 to 1.6 mm (0.5 mm average) and B, resp. 1.6 to 6.3 (1.7 mm). The particle size is depending on the coal moisture. The fluidized bed process with the both fractions was performed at variations of the following parameters: steam velocity (0.07 to 1.7 m/s); raw coal feed rate (4 to 16 kg/h); raw moisture (18 to 43 wt %) and pressure (1.3 and 5 bar). Also the shrinking behaviour of the coal in different pore sizes was tested. Comparing pore size of the oven dried coal to the fluidized bed dried coal, significantly higher inner surface for the oven dried coal was established. To indicate the pore size of raw coal samples were made by freeze drying. Ice expanding should cause higher inner surface compared to oven drying method but no significant difference was established. A significant increase of heat transfer of the particles from A fraction (300 to 350 W/m 2 K0 compared to B (200 to 230 W/m 2 K) was determined. The heat transfer coefficient increased at increasing of the raw coal feed rate, mostly significant for A, due to higher particle contact. In conclusion: the particle convective mechanism is predominant for the heat transfer; development of pressurized fluidized bed drying is not of interest and the question about the total expenditure for crushing and milling remains open

Prototype plant for nuclear process heat (PNP) - operation of the pilot plant for hydrogasification of coal

International Nuclear Information System (INIS)

Bruengel, N.; Dehms, G.; Fiedler, P.; Gerigk, H.P.; Ruddeck, W.; Schrader, L.; Schumacher, H.J.

1988-04-01

The Rheinische Braunkohlenwerke AG developed the process of hydrogasification of coal in a fluidized bed for generation of SNG. On basis of test results obtained in a semi-technical pilot plant of a through-put of 250 kg/h dried coal a large pilot plant was erected processing 10 t/h dried brown coal. This plant was on stream for about 14700 h, of which about 7800 h were with gasifier operation; during this time about 38000 t of dried brown coal of the Rhenish district were processed containing 4 to 25% of ash. At pressures of 60 to 120 bar and temperatures of 800 to 935 0 C carbon conversion rates up to 81 percent and methane amounts of 5000 m 3 (STP)/h were reached. The decisive parameter for methane generation was the hydrogen/coal-ratio. Even at high moisture contents, usually diminishing the methane yield from the coal essentially, by high hydrogen/coal-ratios high methane yields could be obtained. The gasifier itself caused no troubles during the total time operation. Difficulties with the original design of the residual char cooler could be overcome by change-over from water injection to liquid carbon dioxide. The design of the heat recovery system proved well. Alltogether so the size increasement of the gasifier from the semi-technical to the large pilot plant as well as the harmonization of gas generation and gas refining was proved. (orig.) With 20 refs., 20 tabs., 81 figs [de

Mercury concentration in coal - Unraveling the puzzle

Science.gov (United States)

Toole-O'Neil, B.; Tewalt, S.J.; Finkelman, R.B.; Akers, D.J.

1999-01-01

Based on data from the US Geological Survey's COALQUAL database, the mean concentration of mercury in coal is approximately 0.2 ??gg-1. Assuming the database reflects in-ground US coal resources, values for conterminous US coal areas range from 0.08 ??gg-1 for coal in the San Juan and Uinta regions to 0.22 ??gg-1 for the Gulf Coast lignites. Recalculating the COALQUAL data to an equal energy basis unadjusted for moisture differences, the Gulf Coast lignites have the highest values (36.4 lb of Hg/1012 Btu) and the Hams Fork region coal has the lowest value (4.8 lb of Hg/1012Btu). Strong indirect geochemical evidence indicates that a substantial proportion of the mercury in coal is associated with pyrite occurrence. This association of mercury and pyrite probably accounts for the removal of mercury with the pyrite by physical coal cleaning procedures. Data from the literature indicate that conventional coal cleaning removes approximately 37% of the mercury on an equal energy basis, with a range of 0% to 78%. When the average mercury reduction value is applied to in-ground mercury values from the COALQUAL database, the resulting 'cleaned' mercury values are very close to mercury in 'as-shipped' coal from the same coal bed in the same county. Applying the reduction fact or for coal cleaning to eastern US bituminous coal, reduces the mercury input load compared to lower-rank non-deaned western US coal. In the absence of analytical data on as-shipped coal, the mercury data in the COALQUAL database, adjusted for deanability where appropriate, may be used as an estimator of mercury contents of as-shipped coal. ?? 1998 Published by Elsevier Science Ltd. All rights reserved.

Monitor of ash content of coal with X-ray source

International Nuclear Information System (INIS)

Wawrzonek, L.

1983-01-01

The coal ash monitor is used on-line to measure the ash content of raw, washed and blended coals. The instrument consists of a presentation unit and electronic unit. In the presentation unit a compact layer of coal is formed and there is also a radiation measuring system. A plutonium 238 source is used and the backscattered X-rays are detected by a proportional counter. The count rate is processed in the electronic unit and displayed as the ash percentage in the coal. A wide range of Polish coals was analysed. The monitor was tested in a power plant over the period of one year. The ash content in the coal analysed was in the range 5 to 50%. The gauge readings were compared with the pyrolysis results. An accuracy of 3.2% (95% confidence limit) was reached. These results were not corrected for the free moisture content which varied in the range 5 to 15 %. (author)

Utilization of brown coal in FRG power plants

Energy Technology Data Exchange (ETDEWEB)

Kotler, V.R.

1985-07-01

FRG methods are studied for utilizing brown coal in view of the development of Kansk-Achinsk brown coal deposits. The use of brown coal in FRG power plants has increased from 15% in 1950- 1960 to 85% (total output) in 1982, providing 79.4 TWh of electrical energy. The remainder was used for briquetting, pulverization and breeze coke. In 1982 nearly 100 million tons of brown coal were burned by six large power stations (rated capacity 11,400 MW) to produce nearly 80 billion kWh of energy. Measures are discussed taken to reduce slagging and to remove excessive moisture content. Problems are analyzed associated with increased contamination of the atmosphere in areas with high population density (412/km/sup 2/) and cost of suppression is reviewed. According to available data, the cost of preventive measures taken by FRG, USA, Japan and the Netherlands is equal to 30% of the total cost of the energy. The most critical problem is suppression of sulfur dioxide, either by dry or wet scrubbers or by the addition of dry dolomite or lime to the furnace (75% of all SO/sub 2/ emissions in FRG comes from power stations). A method is described developed by RWE based on a series of distribution headers in the upper part of combustion chambers. At best, 70-80% reduction can be achieved. 14 references.

THE EFFECT OF ACTIVATED CARBON SURFACE MOISTURE ON LOW TEMPERATURE MERCURY ADSORPTION

Science.gov (United States)

Experiments with elemental mercury (Hg0) adsorption by activated carbons were performed using a bench-scale fixed-bed reactor at room temperature (27 degrees C) to determine the role of surface moisture in capturing Hg0. A bituminous-coal-based activated carbon (BPL) and an activ...

Evaluation of Assimilated SMOS Soil Moisture Data for US Cropland Soil Moisture Monitoring

Science.gov (United States)

Yang, Zhengwei; Sherstha, Ranjay; Crow, Wade; Bolten, John; Mladenova, Iva; Yu, Genong; Di, Liping

2016-01-01

Remotely sensed soil moisture data can provide timely, objective and quantitative crop soil moisture information with broad geospatial coverage and sufficiently high resolution observations collected throughout the growing season. This paper evaluates the feasibility of using the assimilated ESA Soil Moisture Ocean Salinity (SMOS)Mission L-band passive microwave data for operational US cropland soil surface moisture monitoring. The assimilated SMOS soil moisture data are first categorized to match with the United States Department of Agriculture (USDA)National Agricultural Statistics Service (NASS) survey based weekly soil moisture observation data, which are ordinal. The categorized assimilated SMOS soil moisture data are compared with NASSs survey-based weekly soil moisture data for consistency and robustness using visual assessment and rank correlation. Preliminary results indicate that the assimilated SMOS soil moisture data highly co-vary with NASS field observations across a large geographic area. Therefore, SMOS data have great potential for US operational cropland soil moisture monitoring.

Influence of high-energy impact on the physical and technical characteristics of coal fuels

Science.gov (United States)

Mal'tsev, L. I.; Belogurova, T. P.; Kravchenko, I. V.

2017-08-01

Currently, in the world's large-scale coal-fired power industry, the combustion of pulverized coal is the most widely spread technology of combusting the coals. In recent years, the micropulverization technology for preparation and combustion of the coal has been developed in this field. As applied to the small-scale power industry, the method of combusting the coal in the form of a coal-water slurry has been explored for years. Fine coal powders are produced and used in the pulverized-coal gasification. Therefore, the coal preparation methods that involve high-dispersion disintegration of coals attract the greatest interest. The article deals with the problems of high-energy impact on the coal during the preparation of pulverized-coal fuels and coal-water slurries, in particular, during the milling of the coal in ball drum mills and the subsequent regrinding in disintegrators or the cavitation treatment of the coal-water slurries. The investigations were conducted using samples of anthracite and lignite from Belovskii open-pit mine (Kuznetsk Basin). It is shown that both the disintegration and the cavitation treatment are efficient methods for controlling the fuel characteristics. Both methods allow increasing the degree of dispersion of the coal. The content of the small-sized particles reground by cavitation considerably exceeds the similar figure obtained using the disintegrator. The specific surface area of the coal is increased by both cavitation and disintegration with the cavitation treatment producing a considerably greater effect. Being subjected to the cavitation treatment, most coal particles assume the form of a split characterized by the thermodynamically nonequilibrium state. Under external action, in particular, of temperature, the morphological structure of such pulverized materials changes faster and, consequently, the combustion of the treated coal should occur more efficiently. The obtained results are explained from the physical point of view.

Fundamental study for improvement of dewatering of fine coal/refuse. Final report, August 1981-December 1984

Energy Technology Data Exchange (ETDEWEB)

Chiang, S.H.; Klinzing, G.E.; Morsi, B.I.; Tierney, J.W.; Binkley, T.; Chi, S.M.; Huang, S.; Qamar, I.; Venkatadri, R.

1984-12-01

Fine coal in slurry form must be dewatered to minimize handling and transportation problems and be reduced to a desirable level for subsequent preparation of coal/water mixtures as a substitute utility fuel. The current practice is inadequate for the dewatering of fine coal, particularly for coal particles with sizes smaller than 400 mesh. Therefore, it is most desirable to develop improved mechanical methods for reducing the moisture content of fine coal. In the light of this, a fundamental study of the dewatering of fine coal/refuse was initiated in June 1979 and continued through 1984. The overall objective of the study is to seek improved methods of dewatering through a better understanding of the filtration and post-filtration processes. As a first step, efforts have been focused on the mechanism of dewatering in terms of the basic properties of coal (and refuse) particles and the microstructures of filter cakes, and their relations to filtration rate and final moisture content. Pittsburgh seam-Bruceton Mine coal was used as a base coal. During the past year, filter cakes from coals with widely varying size ranges were micrographically characterized. The effects of a number of surface active agents and of entrapped air bubbles on the filter cake properties were also studied. Modules of the network model for calculating single phase and two phase permeabilities were formulated and tested. The report is divided into four parts: summary and deliverables; work forecast for 1984-1985; detailed description of technical progress; and appendices. 21 refs., 55 figs., 17 tabs.

Special emission measurements on Riley Stoker's advanced CFB pilot facility co-firing non-recyclable de-inking paper fiber and high sulfur eastern bituminous coal

International Nuclear Information System (INIS)

Dixit, V.B.; Mongeon, R.K.; Reicker, E.L.

1993-01-01

Riley Stoker has developed advanced industrial CFB designs that utilize eastern bituminous coals as fuel, and have the potential to use coal in combination with other fuels. Various fiber waste streams in paper recycling processes have sufficient carbonaceous content to be considered as possible sources of such fuels that could fire FBC combustors. The American Paper Institute estimates that by the mid-1990's more than 40% of the waste paper will be recycled, reaching much higher numbers by the year 2000. To evaluate the effectiveness of co-firing such fuels, a test program was conducted on Riley's pilot-scale circulating fluidized bed test facility. A de-inked newsprint derived fiber waste was successfully co-fired with high sulfur coal. The waste fiber material containing approximately 50% moisture had a heating value of 3500 Btu/lb. The coal was strip-mined and contained a lot of clay and excessive quantities of fines making it difficult to burn in conventional boilers. Tests were also conducted with a combination fuel consisting of coal, fiber waste and a high carbon fly ash. In addition to obtaining performance data on combustion efficiency, sulfur capture, and NO x emissions, special emission measurements were also made to quantify the organics, trace metals and hydrochloric acid levels in the flue gas. The co-firing tests achieved a maximum combustion efficiency of 98% and sulfur capture of 90%. The effect of Ca/S mole ratio and temperature is discussed. Although there are no formal regulations in place for FBC systems regarding special emissions, the levels measured were far below the allowable limits for waste incinerators. Materials handling experience on the pilot facility relating to co-firing is also discussed. This is done to identify special considerations for designing commercial facilities. A brief overview of the de-inking waste fiber combustion market is also presented

Numerical investigation of heat transfer characteristics in utility boilers of oxy-coal combustion

International Nuclear Information System (INIS)

Hu, Yukun; Li, Hailong; Yan, Jinyue

2014-01-01

Highlights: • Air-coal and oxy-coal combustion in an industrial scale PF boiler were simulated in ANSYS FLUENT. • The O 2 concentration of 33 vol% in the oxy-coal combustion case matches the air-coal combustion case most closely. • The moisture in the flue gas has little impact on flame temperature, but positive impact on surface incident radiation. - Abstract: Oxy-coal combustion has different flue gas composition from the conventional air-coal combustion. The different composition further results in different properties, such as the absorption coefficient, emissivity, and density, which can directly affect the heat transfer in both radiation and convection zones of utility boilers. This paper numerically studied a utility boiler of oxy-coal combustion and compares with air-coal combustion in terms of flame profile and heat transferred through boiler side walls in order to understand the effects of different operating conditions on oxy-coal boiler retrofitting and design. Based on the results, it was found that around 33 vol% of effective O 2 concentration ([O 2 ] effective ) the highest flame temperature and total heat transferred through boiler side walls in the oxy-coal combustion case match to those in the air-coal combustion case most; therefore, the 33 vol% of [O 2 ] effective could result in the minimal change for the oxy-coal combustion retrofitting of the existing boiler. In addition, the increase of the moisture content in the flue gas has little impact on the flame temperature, but results in a higher surface incident radiation on boiler side walls. The area of heat exchangers in the boiler was also investigated regarding retrofitting. If boiler operates under a higher [O 2 ] effective , to rebalance the load of each heat exchanger in the boiler, the feed water temperature after economizer can be reduced or part of superheating surfaces can be moved into the radiation zone to replace part of the evaporators

Technology Roadmap: High-Efficiency, Low-Emissions Coal-Fired Power Generation

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-07-01

Coal is the largest source of power globally and, given its wide availability and relatively low cost, it is likely to remain so for the foreseeable future. The High-Efficiency, Low-Emissions Coal-Fired Power Generation Roadmap describes the steps necessary to adopt and further develop technologies to improve the efficiency of the global fleet of coal. To generate the same amount of electricity, a more efficient coal-fired unit will burn less fuel, emit less carbon, release less local air pollutants, consume less water and have a smaller footprint. High-efficiency, low emissions (HELE) technologies in operation already reach a thermal efficiency of 45%, and technologies in development promise even higher values. This compares with a global average efficiency for today’s fleet of coal-fired plants of 33%, where three-quarters of operating units use less efficient technologies and more than half is over 25 years old. A successful outcome to ongoing RD&D could see units with efficiencies approaching 50% or even higher demonstrated within the next decade. Generation from older, less efficient technology must gradually be phased out. Technologies exist to make coal-fired power generation much more effective and cleaner burning. Of course, while increased efficiency has a major role to play in reducing emissions, particularly over the next 10 years, carbon capture and storage (CCS) will be essential in the longer term to make the deep cuts in carbon emissions required for a low-carbon future. Combined with CCS, HELE technologies can cut CO2 emissions from coal-fired power generation plants by as much as 90%, to less than 100 grams per kilowatt-hour. HELE technologies will be an influential factor in the deployment of CCS. For the same power output, a higher efficiency coal plant will require less CO2 to be captured; this means a smaller, less costly capture plant; lower operating costs; and less CO2 to be transported and stored.

The clean coal technologies for lignitic coal power generation in Pakistan

International Nuclear Information System (INIS)

Mir, S.; Raza, Z.; Aziz-ur-Rehman, A.

1995-01-01

Pakistan contains huge reserves of lignitic coals. These are high sulphur, high ash coals. In spite of this unfortunate situation, the heavy demand for energy production, requires the development utilization of these indigenous coal reserves to enhance energy production. The central of the environmental pollution caused by the combustion of these coals has been a major hindrance in their utilization. Recently a substantial reduction in coal combustion emissions have been achieved through the development of clean coal technologies. Pakistan through the transfer and adaptation of the advanced clean coal technologies can utilize incurring the high sulphur coals for energy production without incurring the environmental effects that the developed countries have experienced in the past. The author discusses the recently developed clean coal utilization technologies, their applications economies and feasibility of utilization with specific reference to Pakistan''s coal. (author)

Ge distribution in the Wulantuga high-germanium coal deposit in the Shengli coalfield, Inner Mongolia, northeastern China

Energy Technology Data Exchange (ETDEWEB)

Du, Gang [Key Laboratory of Marginal Sea Geology, Chinese Academy of Sciences (China)]|[Coal Geology Bureau of Inner Mongolia, Hohhot, 010051 (China); Zhuang, Xinguo [Institute of Sedimentary Basin and Mineral, Faculty of Earth Resources, China University of Geosciences, Hubei, 430074 (China)]|[State Key Laboratory of Geological Processes and Mineral Resources, China University of Geosciences, Hubei, 430074 (China); Querol, Xavier; Izquierdo, Maria; Alastuey, Andres; Moreno, Teresa; Font, Oriol [Institute of Earth Science ' Jaume Almera' , CSIC, C/ LLuis Sole Sabaris s/n, 08028 Barcelona (Spain)

2009-03-01

The geological and geochemical controls of the Ge distribution in the Cretaceous Wulantuga high-Germanium coal deposit in the Shengli coal field, Inner Mongolia are investigated. This paper focuses mainly on the spatial distribution of the Ge contents in coal. The high-Ge coals mainly occur in three splits of the 6 coal in the southwestern part of the Shengli coal field. Mean germanium contents in the coal range from 32 to 820 {mu}g/g, with a mean value of 137 {mu}g/g, on a bulk coal basis (mean of 939 coal samples from 75 boreholes in the 6 coal seam) in an area of 2.2 km{sup 2}. The highest Ge content occurs SW of 6 coal seam, close to the margins of the coal basin, decreasing with a fan-shaped trend towards NW, the direction of the coal basin. There is an negative correlation between the mean Ge content and the thickness of the coal seam. Different distribution patterns of Ge content were found in vertical profiles. High Ge concentrations may occur in the middle parts of coal seams, at the bottom and/or the top of thick coal seams and inconspicuous variation. A major organic affinity was determined for Ge, with a special enriched in the banded bright and semibright coal. The high-Ge coals and the coalified wood in the sandstone overlaying the 6-1 coal highly enriched in Ge, As, Sb, W, Cs, Tl, Be, and Hg. The Late Jurassic silicified volcanic rocks in the NW of the Ge coal deposit relatively high enriched in Ge, Ga, Sb, As, Cs, Be, Ge and Hg. The correlation coefficients among the elements enriched showed marked variations at close sites in this deposit, suggesting a possible diagenetic origin of the geochemical anomaly. The main Ge anomaly was attributed to early Cretaceous hydrothermal fluids circulating through the fault systems and porous volcanic rocs, probably from the subjacent granitoid rocks. The fault systems, the porous coarse clastic rocks overlying coal seam and the lithotype of coal played an important role in the transport and trapping of Ge. A

Fiscal 1998 overseas geological structure survey. Japan-China joint coal survey Mei-Xian project; 1998 nendo kaigai chishitsu kozo nado chosa hokokusho. Nippon Chugoku sekitan kyodo tansa Mei-Xian project

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Japan-China joint coal survey was made through seismic prospecting by Japanese group and drilling prospecting by Chinese group. Mei-Xian mine property includes coal seams of the Jurassic period, and is covered with the quaternary period stratum without any coal seam. The base of the quaternary period stratum exists at depth of 50-400m, while the coal seams at depth of 300-700m. Among 11 existing seams, the 1st and 5th seams are main objects for prospecting. The 5th seam of 0.2-8.96m (2.95m in average) thick is the most expected important one, distributing all over the mine property. The 5th seam also has branch seams spreading over 2.5km from east to west and 1.2km from south to north in the center part of the mine property. The 1st seam of 0-8.62m (2.90m in average) thick is most thick in the south part of the mine property. The theoretical amount of coal deposits in the whole coal seam is estimated to be nearly 290,000,000t by Chinese group (nearly 50% of it in the 5th seam). That is also estimated to be nearly 346,000,000t by Japanese group (155,000,000t in the 5th seam). Both 1st and 5th seams are composed of sub-bituminous coal. (NEDO)

Impacts of Natural Surfactant Soybean Phospholipid on Wettability of High-rank Coal Reservoir

Science.gov (United States)

Lyu, S.; Xiao, Y.; Yuan, M.; Wang, S.

2017-12-01

It is significant to change the surface wettability of coal rock with the surfactant in coal mining and coalbed methane exploitation. Soybean phospholipid (SP) is a kind of natural zwitterionic surfactant which is non-toxic and degradable. In order to study the effects of soybean phospholipid on wettability of high-rank coal in Qinshui Basin, some experiments including surface tension test, contact angle measurement on the coal surface, coal fines imbibition, observation of dispersion effect and gas permeability test were carried out, and water locking mechanism of fracturing fluid in micro fractures of coal reservoir was analyzed. The results show that the surface of high-rank coal was negatively charged in solution and of weak hydrophilicity. The soybean phospholipid with the mass fraction of 0.1% reduced the surface tension of water by 69%, and increased the wettability of coal. Meanwhile, the soybean phospholipid helped coal fines to disperse by observation of the filter cake with the scanning electron microscope. The rising rate of soybean phospholipid solution in the pipe filled with coal fines was lower than that of anionic and cationic surfactant, higher than that of clean water and non-ionic surfactant. Composite surfactant made up of soybean phospholipid and OP-10 at the ratio of 1:3 having a low surface tension and large contact angle, reduced the capillary force effectively, which could be conducive to discharge of fracturing fluid from coal reservoir micro fracture and improve the migration channels of gas. Therefore it has a broad application prospect.

Working group report: methane emissions from coal mining

International Nuclear Information System (INIS)

Kruger, D.

1993-01-01

The process of coalification inherently generates methane and other byproducts. The amount of methane released during coal mining is a function of coal rank and depth, gas content, and mining methods, as well as other factors such as moisture. In most underground mines, methane is removed by drawing large quantities of air through the mine releasing the air into the atmosphere. In surface mines, exposed coal faces and surfaces, as well as areas of coal rubble created by blasting operations are believed to be the major sources of methane. A portion of the methane emitted from coal mining comes from post-mining activities such as coal processing, transportation, and utilisation. Some methane is also released from coal waste piles and abandoned mines. This paper highlights difficulties with previous methane emission studies namely: absence of data on which to base estimates; use of national data to develop global estimates; failure to include all possible emission sources; overreliance on statistical estimation methodologies. It recommends a 'tiered' approach for the estimation of emissions from underground mines, surface mines and post-mining activities. For each source, two or more approaches (or 'tiers') are presented, with the first tier requiring basic and readily available data and higher tiers requiring additional data. 29 refs., 3 tabs

Release of inorganic trace elements from high-temperature gasification of coal

Energy Technology Data Exchange (ETDEWEB)

Blaesing, Marc

2012-05-30

The development of cleaner, more efficient techniques in next-generation coal power plants is becoming increasingly important, especially regarding to the discussion of the influence of CO{sub 2} emissions on global warming. A promising coal utilisation process is the integrated gasification combined cycle process. The direct use of the raw gas requires gas clean-up to prevent downstream parts of the gasifier from several problems. An increased efficiency and a decreased amount of harmful species can be achieved through hot fuel gas cleaning. This clean-up technique requires a comprehensive knowledge of the release characteristics of inorganic coal constituents. The aim of this thesis was to provide enhanced knowledge of the effect of key process parameters and of the chemical constitution of coal on the release of Na, K, S, and Cl species from high-temperature coal gasification. The experimental setup consisted of atmospheric flow tube furnaces and a pressurised furnace. In-situ analysis of the product gas was carried out using molecular beam mass spectrometry. A broad spectrum of different coals with assumed qualitative and quantitative differences in the release characteristics was investigated. Additionally, experiments with model substances were performed. The results of the experimental investigation were compared with thermodynamic calculations. Finally, recommendations, for the operation of a high-temperature gasifier are formulated. (orig.)

[Soil organic pollution characteristics and microbial properties in coal mining areas of Mentougou].

Science.gov (United States)

Jia, Jian-Li; Zhang, Yue; Wang, Chen; Li, Dong; Liu, Bo-Wen; Liu, Ying; Zhao, Le; Yang, Si-Qi

2011-03-01

Soil micro-ecosystem including organic pollution characteristics, basic physicochemical parameters, and microbial properties was analyzed which contaminated with organic pollutants in coal mining area. Results showed that the organic pollution level in coal mining area soils distributed from 0.4 to 1.5 mg/g dry soil, which was 1. 5-6 times as much as the background sample. Furthermore, the column chromatography and GC-MS analysis revealed that content of lightly components including saturated and aromatic hydrocarbons exceeded 40%, specifically was alkenes (> C15), hydrocarbon derivatives, and a small amount aromatic hydrocarbons. Totally, the components of organic pollutants extracted in soils were similar to which in coal gangue samples, illustrating the source of soil pollution to a certain extent in coal mining areas. The physicochemical factors such as nutrient level and moisture contents were not conducive to the growth and reproduction of microbe except pH level, which might show inhibition to microbial activities. Microbial density of pollutant soils in coal mining areas was totally low, with specific amount 10(4)-10(5) cell/g dry soil and FDA activity 2.0-2.9 mg/(g x min). Generally, the microbial density and activity were decreased as the enhancing pollution level. However, in-depth analysis was needed urgently because of the complex impact of environmental conditions like pH, moisture, and nutrition.

Validation of soil moisture ocean salinity (SMOS) satellite soil moisture products

Science.gov (United States)

The surface soil moisture state controls the partitioning of precipitation into infiltration and runoff. High-resolution observations of soil moisture will lead to improved flood forecasts, especially for intermediate to large watersheds where most flood damage occurs. Soil moisture is also key in d...

Integrated Waste Treatment Unit (IWTU) Input Coal Analyses and Off-Gass Filter (OGF) Content Analyses

Energy Technology Data Exchange (ETDEWEB)

Jantzen, Carol M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Missimer, David M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Guenther, Chris P. [National Energy Technology Lab. (NETL), Morgantown, WV (United States); Shekhawat, Dushyant [National Energy Technology Lab. (NETL), Morgantown, WV (United States); VanEssendelft, Dirk T. [National Energy Technology Lab. (NETL), Morgantown, WV (United States); Means, Nicholas C. [AECOM Technology Corp., Oak Ridge, TN (United States)

2015-04-23

A full engineering scale Fluidized Bed Steam Reformer (FBSR) system is being used at the Idaho Nuclear Technology and Engineering Center (INTEC) to stabilize acidic Low Activity Waste (LAW) known as Sodium Bearing Waste (SBW). The INTEC facility, known as the Integrated Waste Treatment Unit (IWTU), underwent an Operational Readiness Review (ORR) and a Technology Readiness Assessment (TRA) in March 2014. The IWTU began non-radioactive simulant processing in late 2014 and by January, 2015 ; the IWTU had processed 62,000 gallons of simulant. The facility is currently in a planned outage for inspection of the equipment and will resume processing simulated waste feed before commencing to process 900,000 gallons of radioactive SBW. The SBW acidic waste will be made into a granular FBSR product (carbonate based) for disposal in the Waste Isolation Pilot Plant (WIPP). In the FBSR process calcined coal is used to create a CO2 fugacity to force the waste species to convert to carbonate species. The quality of the coal, which is a feed input, is important because the reactivity, moisture, and volatiles (C,H,N,O, and S) in the coal impact the reactions and control of the mineralizing process in the primary steam reforming vessel, the Denitration and Mineralizing Reformer (DMR). Too much moisture in the coal can require that additional coal be used. However since moisture in the coal is only a small fraction of the moisture from the fluidizing steam this can be self-correcting. If the coal reactivity or heating value is too low then the coal feedrate needs to be adjusted to achieve the desired heat generation. Too little coal and autothermal heat generation in the DMR cannot be sustained and/or the carbon dioxide fugacity will be too low to create the desired carbonate mineral species. Too much coal and excess S and hydroxide species can form. Excess sulfur from coal that (1) is too rich in sulfur or (2) from overfeeding coal can promote wall scale and contribute to corrosion