WorldWideScience

Sample records for high purity gadolinium

  1. Hydrogen in-situ refining method for preparing high purity gadolinium

    Energy Technology Data Exchange (ETDEWEB)

    Li, Guoling [Beijing National Laboratory of Molecular Sciences, State Key Laboratory of Rare Earth Materials Chemistry and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Department of Materials Physics and Chemistry, University of Science and Technology Beijing, NO. 30, Xueyuan Road, Beijing 100083 (China); Li, Li [Beijing National Laboratory of Molecular Sciences, State Key Laboratory of Rare Earth Materials Chemistry and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Fu, Kai [Beijing National Laboratory of Molecular Sciences, State Key Laboratory of Rare Earth Materials Chemistry and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Department of Materials Physics and Chemistry, University of Science and Technology Beijing, NO. 30, Xueyuan Road, Beijing 100083 (China); Wang, Chongyun [Department of Materials Physics and Chemistry, University of Science and Technology Beijing, NO. 30, Xueyuan Road, Beijing 100083 (China); Zheng, Jie [Beijing National Laboratory of Molecular Sciences, State Key Laboratory of Rare Earth Materials Chemistry and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Xu, Li [State Grid Smart Grid Research Institute, Future Science& Technology Park, Changping, Beijing 102211 (China); Tian, Wenhuai [Department of Materials Physics and Chemistry, University of Science and Technology Beijing, NO. 30, Xueyuan Road, Beijing 100083 (China); Li, Xingguo, E-mail: xgli@pku.edu.cn [Beijing National Laboratory of Molecular Sciences, State Key Laboratory of Rare Earth Materials Chemistry and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China)

    2015-11-05

    The removal of non-metallic impurities, especially oxygen and nitrogen, from the rare-earth metal gadolinium (Gd) is challenging, due to their strong affinity to Gd metal. Herein we present an effective approach to prepare high purity Gd via a novel hydrogen in-situ refining method. The final concentrations of oxygen and nitrogen could be reduced to 30 and 19 mass ppm, respectively. The changes of lattice parameters were derived from XRD; enthalpy values and gaseous speciation associated with the gas–solid physiochemical reactions were determined through a combination of DSC/MS measurements and thermodynamic calculations. The results show that oxygen and nitrogen can be efficiently removed by degassing Gd with dissolved hydrogen. The underlying mechanism for the refinement is discussed systematically in this paper. - Highlights: • Hydrogen can shuttle gadolinium freely at high temperature. • The concentration of O and N dropped to 30 ppm and 19 ppm, respectively. • The hydrogen content could finally decrease to 17 ppm. • Hydrogen, water and ammonia signals can be detected successfully. • This method is environment friendly and no other recontaminations.

  2. The giant magnetocaloric effect in Gd5Si2Ge2 with low purity gadolinium

    Institute of Scientific and Technical Information of China (English)

    ZHANG Tiebang; CHEN Yungui; FU Hao; TENG Baohua; TANG Yongbai; TU Mingjing

    2005-01-01

    The giant magnetocaloric effect Gd5Si2Ge2 alloy was prepared with 99wt% low purity commercial Gd. Powder XRD and magnetic measurements showed that the Gd5Si2Ge2 alloy annealed at 1200℃ for 1 h had a significant magnetic- crystallographic first order phase transition at about 270 K. The maximal magnetic entropy change is 17.55 J·kg-1·K-1 under a magnetic field change of 0―5 T. The distinct increase of magnetic entropy change belongs to the first-order phase transition from the orthorhombic Gd5Si4-type to the monoclinic Gd5Si2Ge2-type after high temperature heat-treatment.

  3. Preparation of High Purity Amorphous Boron Powder

    Directory of Open Access Journals (Sweden)

    K.V. Tilekar

    2005-10-01

    Full Text Available Amorphous boron powder of high purity (92-94 % with a particle size of l-2 mm is preferred as a fuel for fuel-rich propellants for integrated rocket ramjets and for igniter formulations. Thispaper describes the studies on process optimisation of two processes, ie, oxidative roasting of boron (roasting boron in air and roasting boron with zinc in an inert medium for preparing high purity boron. Experimental studies reveal that roasting boron with zinc at optimised process conditions yields boron of purity more than 93 per cent, whereas oxidative roasting method yields boron of purity - 92 per cent. Oxidative roasting has comparative edge over the other processes owing to its ease of scale-up and simplicity

  4. Shape rheocasting of high purity aluminium

    CSIR Research Space (South Africa)

    Curle, UA

    2011-03-01

    Full Text Available It is demonstrated experimentally that using the Council for Scientific and Industrial Research Rheo Casting System and high pressure die casting it is possible to semi-solid process and cast into a shape high purity aluminium without a...

  5. Nonlinear control of high purity distillation columns

    OpenAIRE

    Groebel, Markus; Allgöwer, Frank; Storz, Markus; Gilles, Ernst Dieter

    1994-01-01

    Two simple models of distillation columns are studied to investigate their suitability for the practical use with exact I/O-linearization. An extension of exact I/O-linearization, the asymptotically exact I/O-linearization is applied to the control of a high purity distillation column, using one of these models to derive the static state feedback law. Simulation studies demonstrate the advantage of asymptotically exact I/O-linearization versus classical exact I/O-linearization techniques. Exp...

  6. Gadolinium loaded plastic scintillators for high efficiency neutron detection

    Science.gov (United States)

    Ovechkina, Lena; Riley, Kent; Miller, Stuart; Bell, Zane; Nagarkar, Vivek

    2009-08-01

    Gadolinium has the highest thermal neutron absorption cross section of any naturally occurring element, and emits conversion electrons as well as atomic X-rays in over 50% of its neutron captures, which makes it a useful dopant in scintillators for detecting thermal neutrons. Gadolinium isopropoxide was studied as a possible dopant for styrene-based plastic scintillators as a convenient and inexpensive method to produce high-efficiency thermal neutron detectors. Plastic scintillators with gadolinium weight concentrations of up to 3% were transparent, uniform and defect-free and were characterized with spectral measurements performed under x-ray and neutron irradiation. The new material has the same characteristic emission of styrene with a maximum at approximately 425 nm, and a light output of 76% relative to the undoped plastic. A 13 mm thick sample containing 0.5% gadolinium by weight detected 46% of incident thermal neutrons, which makes this an attractive material for a variety of applications.

  7. Highly Accurate Sensor for High-Purity Oxygen Determination Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In this STTR effort, Los Gatos Research (LGR) and the University of Wisconsin (UW) propose to develop a highly-accurate sensor for high-purity oxygen determination....

  8. Ultra-high purity arsenic for MBE

    Energy Technology Data Exchange (ETDEWEB)

    Barnes, R.G.L. (Johnson Matthey PLC, Royston (UK)); Emeny, M.T.; Whitehouse, C.R.; Lee, D. (Royal Signals and Radar Ets., Great Malvern (UK))

    1990-11-01

    A requirement for high purity elemental arsenic for use in compound semiconductors has become well established. The capabilities of molecular beam epitaxy as a fabrication technique are best exploited if the arsenic used has particular additional features. Prominent among these are a uniform distribution of impurities at levels down to 10 ppb, and a geometrically uniform distribution of material in the charge used. Once material such as this, of 7N purity or better, emerges from its processing, a major vulernability is from recontamination. Prevention of this is a further important requirement. Detailed examination of possible process strategies has led to an approach targeted on the manufacture of solid arsenic ''charges'' especially suited for MBE application. Factors involved are reviewed. An outline of the consequent production operation is described, based on vapour phase and laser processing. Continuous long-term reproducibility is achieved. Analysis of the product by glow discharge mass spectrometry with state-of-the-art sensitivity is used for qualification of the product and process. Results from this and supplementary techniques which have been used are presented. The utilisation of this material for GaAs has been widely tested successfully. The outcome of some of that work is shown. (orig.).

  9. Multielement trace determination in high purity advanced ceramics and high purity metals

    Indian Academy of Sciences (India)

    R Matschat; H-J Heinrich; M Czerwensky; S Kuxenko; H Kipphardt

    2005-07-01

    In the field of advanced ceramics two CRMs were developed in the last few years by the Federal Institute for Materials Research and Testing, one for silicon nitride and one for silicon carbide. Besides their application by industry they are appropriate to be used for the validation of special methods used for trace determination in accordance with high purity materials. This is demonstrated, for example, on ultrapure silicon carbide which was analysed by solid sampling electrothermal atomic absorption spectrometry (SS ET AAS). BAM is also certifying primary pure reference materials used as the National Standards for inorganic analysis in Germany. The crucial point of this project is the certification of the total purity of high purity materials, each representing one element of the periodic table. A variety of different analytical methods was necessary to determine the trace contents of metallic and non-metallic impurities from almost the whole periodic table in the high purity materials. The primary CRMs of copper, iron and molybdenum are used as examples to demonstrate the modus operandi, analytical effects observed by using high resolution ICP mass spectrometry (HR ICP–MS) and the results.

  10. Workshop on Preserving High Purity Uranium-233

    Energy Technology Data Exchange (ETDEWEB)

    Krichinsky, Alan M [ORNL; Giaquinto, Joseph [ORNL; Canaan, R Douglas {Doug} [ORNL

    2016-01-01

    A workshop was held on at the MARC X conference to provide a forum for the scientific community to communicate needs for high-purity 233U and its by-products in order to preserve critical items otherwise slated for downblending and disposal. Currently, only a small portion of the U.S. holdings of separated 233U is being preserved. However, many additional kilograms of 233U (>97% pure) still are destined to be downblended which will permanently destroy their potential value for many other applications. It is not likely that this material will ever be replaced due to a lack of operating production capability. Summaries of information conveyed at the workshop and feedback obtained from the scientific community are presented herein.

  11. Dynamic shear deformation in high purity Fe

    Energy Technology Data Exchange (ETDEWEB)

    Cerreta, Ellen K [Los Alamos National Laboratory; Bingert, John F [Los Alamos National Laboratory; Trujillo, Carl P [Los Alamos National Laboratory; Lopez, Mike F [Los Alamos National Laboratory; Gray, George T [Los Alamos National Laboratory

    2009-01-01

    The forced shear test specimen, first developed by Meyer et al. [Meyer L. et al., Critical Adiabatic Shear Strength of Low Alloyed Steel Under Compressive Loading, Metallurgical Applications of Shock Wave and High Strain Rate Phenomena (Marcel Decker, 1986), 657; Hartmann K. et al., Metallurgical Effects on Impact Loaded Materials, Shock Waves and High Strain rate Phenomena in Metals (Plenum, 1981), 325-337.], has been utilized in a number of studies. While the geometry of this specimen does not allow for the microstructure to exactly define the location of shear band formation and the overall mechanical response of a specimen is highly sensitive to the geometry utilized, the forced shear specimen is useful for characterizing the influence of parameters such as strain rate, temperature, strain, and load on the microstructural evolution within a shear band. Additionally, many studies have utilized this geometry to advance the understanding of shear band development. In this study, by varying the geometry, specifically the ratio of the inner hole to the outer hat diameter, the dynamic shear localization response of high purity Fe was examined. Post mortem characterization was performed to quantify the width of the localizations and examine the microstructural and textural evolution of shear deformation in a bcc metal. Increased instability in mechanical response is strongly linked with development of enhanced intergranular misorientations, high angle boundaries, and classical shear textures characterized through orientation distribution functions.

  12. Delta Doping High Purity CCDs and CMOS for LSST

    Science.gov (United States)

    Blacksberg, Jordana; Nikzad, Shouleh; Hoenk, Michael; Elliott, S. Tom; Bebek, Chris; Holland, Steve; Kolbe, Bill

    2006-01-01

    A viewgraph presentation describing delta doping high purity CCD's and CMOS for LSST is shown. The topics include: 1) Overview of JPL s versatile back-surface process for CCDs and CMOS; 2) Application to SNAP and ORION missions; 3) Delta doping as a back-surface electrode for fully depleted LBNL CCDs; 4) Delta doping high purity CCDs for SNAP and ORION; 5) JPL CMP thinning process development; and 6) Antireflection coating process development.

  13. Structural and magnetic phase transitions in gadolinium under high pressures and low temperatures

    Science.gov (United States)

    Samudrala, Gopi K.; Tsoi, Georgiy M.; Weir, Samuel T.; Vohra, Yogesh K.

    2014-10-01

    High pressure structural transition studies have been carried out on rare earth metal gadolinium in a diamond anvil cell at room temperature to 169 GPa. Gadolinium has been compressed to 38% of its initial volume at this pressure. With increasing pressure, a crystal structure sequence of hcp → Sm-type → dhcp → fcc → dfcc → monoclinic has been observed in our studies on gadolinium. The measured equation of state of gadolinium is presented to 169 GPa at ambient temperature. Magnetic ordering temperature of gadolinium has been studied using designer diamond anvils to a pressure of 25 GPa and a temperature of 10 K. The magnetic ordering temperature has been determined from the four-point electrical resistivity measurements carried out on gadolinium. Our experiments show that the magnetic transition temperature decreases with increasing pressure to 19 GPa and then increases when gadolinium is subjected to higher pressures.

  14. Characterisation of two AGATA asymmetric high purity germanium capsules

    Energy Technology Data Exchange (ETDEWEB)

    Colosimo, S.J., E-mail: sjc@ns.ph.liv.ac.uk [Department of Physics, Oliver Lodge Laboratory, University of Liverpool, Liverpool L69 7ZE (United Kingdom); Moon, S.; Boston, A.J.; Boston, H.C.; Cresswell, J.R.; Harkness-Brennan, L.; Judson, D.S. [Department of Physics, Oliver Lodge Laboratory, University of Liverpool, Liverpool L69 7ZE (United Kingdom); Lazarus, I.H. [STFC Daresbury, Daresbury, Warrington WA4 4AD (United Kingdom); Nolan, P.J. [Department of Physics, Oliver Lodge Laboratory, University of Liverpool, Liverpool L69 7ZE (United Kingdom); Simpson, J. [STFC Daresbury, Daresbury, Warrington WA4 4AD (United Kingdom); Unsworth, C. [Department of Physics, Oliver Lodge Laboratory, University of Liverpool, Liverpool L69 7ZE (United Kingdom)

    2015-02-11

    The AGATA spectrometer is an array of highly segmented high purity germanium detectors. The spectrometer uses pulse shape analysis in order to track Compton scattered γ-rays to increase the efficiency of nuclear spectroscopy studies. The characterisation of two high purity germanium detector capsules for AGATA of the same A-type has been performed at the University of Liverpool. This work will examine the uniformity of performance of the two capsules, including a comparison of the resolution and efficiency as well as a study of charge collection. The performance of the capsules shows good agreement, which is essential for the efficient operation of the γ-ray tracking array.

  15. High purity tellurium production using dry refining processes

    Indian Academy of Sciences (India)

    N R Munirathnam; D S Prasad; J V Rao; T L Prakash

    2005-07-01

    Tellurium (99.95 at.% purity) is purified using dry processes such as selective vapourization and zone melting in a thoroughly etched and cleaned quartz boat, under continuous flow of hydrogen (H2) gas. The tellurium ingot was quadruple zone refined (QZR) under continuous flow of H2 gas. Thus, the purified tellurium of ultra high purity (UHP) grade is analysed for 60 impurity elements in the periodic table using glow discharge mass spectrometer (GDMS). The sum of all elemental impurities indicate that the purity of tellurium as 7N (99.99999 at.%). The total content of gas and gas forming impurities like O, N and C are found to be within acceptable limits for opto-electronic applications.

  16. Thermocurrent dosimetry with high purity aluminum oxide

    Energy Technology Data Exchange (ETDEWEB)

    Fullerton, G.D.; Cameron, J.R.; Moran, P.R.

    1976-01-01

    The application of thermocurrent (TC) to ionizing radiation dosimetry was studied. It was shown that TC in alumina (Al/sub 2/O/sub 3/) has properties that are suited to personnel dosimetry and environmental monitoring. TC dosimeters were made from thin disks of alumina. Aluminum electrodes were evaporated on each side: on one face a high voltage electrode and on the opposite face a measuring electrode encircled by a guard ring. Exposure to ionizing radiation resulted in stored electrons and holes in metastable trapping sites. The signal was read-out by heating the dosimeter with a voltage source and picnometer connected in series between the opposite electrodes. The thermally remobilized charge caused a transient TC. The thermogram, TC versus time or temperature, is similar to a TL glow curve. Either the peak current or the integrated current is a measure of absorbed dose. Six grades of alumina were studied from a total of four commercial suppliers. All six materials displayed radiation induced TC signals. Sapphire of uv-grade quality from the Adolf Meller Co. (AM) had the best dosimetry properties of those investigated. Sources of interference were studied. Thermal fading, residual signal and radiation damage do not limit TC dosimetry. Ultraviolet light can induce a TC response but it is readily excluded with uv-opaque cladding. Improper surface preparation prior to electrode evaporation was shown to cause interference. A spurious TC signal resulted from polarization of surface contaminants. Spurious TC was reduced by improved cleaning prior to electrode application. Polished surfaces resulted in blocking electrodes and caused a sensitivity shift due to radiation induced thermally activated polarization. This was not observed with rough cut surfaces.

  17. Low cost routes to high purity silicon and derivatives thereof

    Energy Technology Data Exchange (ETDEWEB)

    Laine, Richard M; Krug, David James; Marchal, Julien Claudius; Mccolm, Andrew Stewart

    2013-07-02

    The present invention is directed to a method for providing an agricultural waste product having amorphous silica, carbon, and impurities; extracting from the agricultural waste product an amount of the impurities; changing the ratio of carbon to silica; and reducing the silica to a high purity silicon (e.g., to photovoltaic silicon).

  18. Recrystallization behavior of high purity aluminum at 300 ℃

    Institute of Scientific and Technical Information of China (English)

    DU Yu-xuan; ZHANG Xin-ming; YE Ling-ying; LUO Zhi-hui

    2006-01-01

    The recrystallization behavior of 98.5% cold rolled high purity aluminum foils annealed at 300 ℃ was investigated, and the evolution of the microstructures was followed by electron back scattered diffraction(EBSD). The results show that the recrystallization process of the high purity aluminum foils at 300 ℃ is a mixture of discontinuous- and continuous-recrystallization.The orientations of the recrystallization nuclei include not only the cube orientation, but also other orientations such as some near deformation texture components which are the results of strong recovery process. However, such continuously recrystallized grains are usually associated with relatively high free energy, so they would be consumed by the discontinuously-recrystallized grains (cube-oriented grains) in subsequent annealing. On the other hand, the pattern quality index of recrystallized grains shows dependence on the crystal orientation which might introduce some errors into evaluating volume fraction of recrystallization by integrating pattern quality index of EBSD.

  19. Evaluation of purity with its uncertainty value in high purity lead stick by conventional and electro-gravimetric methods

    OpenAIRE

    Singh, Nahar; SINGH, Niranjan; Tripathy, S Swarupa; Soni, Daya; Singh, Khem; GUPTA Prabhat K

    2013-01-01

    Background A conventional gravimetry and electro-gravimetry study has been carried out for the precise and accurate purity determination of lead (Pb) in high purity lead stick and for preparation of reference standard. Reference materials are standards containing a known amount of an analyte and provide a reference value to determine unknown concentrations or to calibrate analytical instruments. A stock solution of approximate 2 kg has been prepared after dissolving approximate 2 g of Pb stic...

  20. The GALATEA test-facility for High Purity Germanium Detectors

    CERN Document Server

    Abt, I; Doenmez, B; Garbini, L; Irlbeck, S; Majorovits, B; Palermo, M; Schulz, O; Seitz, H; Stelzer, F

    2014-01-01

    GALATEA is a test facility designed to investigate bulk and surface effects in high purity germanium detectors. A vacuum tank houses an infrared screened volume with a cooled detector inside. A system of three stages allows an almost complete scan of the detector. The main feature of GALATEA is that there is no material between source and detector. This allows the usage of alpha and beta sources as well as of a laser beam to study surface effects. A 19-fold segmented true-coaxial germanium detector was used for commissioning.

  1. The GALATEA test-facility for high purity germanium detectors

    Science.gov (United States)

    Abt, I.; Caldwell, A.; Dönmez, B.; Garbini, L.; Irlbeck, S.; Majorovits, B.; Palermo, M.; Schulz, O.; Seitz, H.; Stelzer, F.

    2015-05-01

    GALATEA is a test facility designed to investigate bulk and surface effects in high purity germanium detectors. A vacuum tank houses a cold volume with the detector inside. A system of three precision motorized stages allows an almost complete scan of the detector. The main feature of GALATEA is that there is no material between source and detector. This allows the usage of alpha and beta sources to study surface effects. A 19-fold segmented true-coaxial germanium detector was used for commissioning. A first analysis of data obtained with an alpha source is presented here.

  2. The GALATEA test-facility for high purity germanium detectors

    Energy Technology Data Exchange (ETDEWEB)

    Abt, I.; Caldwell, A.; Dönmez, B.; Garbini, L.; Irlbeck, S.; Majorovits, B.; Palermo, M., E-mail: palermo@mpp.mpg.de; Schulz, O.; Seitz, H.; Stelzer, F.

    2015-05-11

    GALATEA is a test facility designed to investigate bulk and surface effects in high purity germanium detectors. A vacuum tank houses a cold volume with the detector inside. A system of three precision motorized stages allows an almost complete scan of the detector. The main feature of GALATEA is that there is no material between source and detector. This allows the usage of alpha and beta sources to study surface effects. A 19-fold segmented true-coaxial germanium detector was used for commissioning. A first analysis of data obtained with an alpha source is presented here.

  3. Competitive growth of high purity aluminum grains in directional solidification

    Institute of Scientific and Technical Information of China (English)

    ZHANG Jiao; SHU Da; WANG De-lin; SUN Bao-de; CHEN Gang

    2006-01-01

    A self-made directional solidification setup was used to prepare high purity aluminum ingots of 100mm in diameter. The morphology of the growth interface was detected by SEM and AFM, and the grain lattice orientation was detected by XRD. The results indicate that the grains suffer competitive growth under any conditions in experiments. The lattice orientation of the preferred grains is determined by the flow field above the solid-liquid interface. The horizontal lattice position does not change during the growth process. However, the lattice orientation in the growth direction varies with the growth velocity and approaches to [100]gradually during the growth process.

  4. Textures in high purity aluminum foils and AA3004 sheets

    Institute of Scientific and Technical Information of China (English)

    肖亚庆; 张新明; 唐建国; 邓运来; 陈志永

    2003-01-01

    The simulation of rolling texture with "minimum shear principle" and the strengthening of cube recrystallization texture by inhomogeneous rolling, low strain deformation and multistage annealing, of the formation and evolution of texture in high purity Al were presented. The plastic anisotropy of crystalline materials were also summarized, including determination of the co-yield surfaces and condition of slipping as well as mechanical twinning, prediction of plastic anisotropy of deep drawing with modified Tuckers method, evolution of earing behavior of Al alloy sheets for deep drawing with CMTP approach, and construction of texture balance design and some technologies to suppress plastic anisotropy in practical production.

  5. Recent developments in high purity niobium metal production at CBMM

    Energy Technology Data Exchange (ETDEWEB)

    Abdo, Gustavo Giovanni Ribeiro, E-mail: Gustavo.abdo@cbmm.com.br; Sousa, Clovis Antonio de Faria, E-mail: Clovis@cbmm.com.br; Guimarães, Rogério Contato, E-mail: Rogerio.guimaraes@cbmm.com.br; Ribas, Rogério Marques, E-mail: Rogerio.ribas@cbmm.com.br; Vieira, Alaércio Salvador Martins, E-mail: Alaercio.vieira@cbmm.com.b; Menezes, Andréia Duarte, E-mail: Amenezes@cbmm.com.br; Fridman, Daniel Pallos, E-mail: Daniel.fridman@cbmm.com.br; Cruz, Edmundo Burgos, E-mail: Edmundo@cbmm.com.br [CBMM – Companhia Brasileira de Metalurgia e Mineração Córrego da Mata, s/n Araxá, Minas Gerais 38183-903 Brazil (Brazil)

    2015-12-04

    CBMM is a global supplier of high quality niobium products including pure niobium, the focus of this paper. CBMM’s position has been consolidated over three decades of producing high purity niobium metal ingots. The company supplies, among other products, commercial and reactor grade niobium ingots. One of the main uses of CBMM’s ingots is for the manufacture of particle accelerators (superconducting radio frequency – SRF – cavities), where the purity and homogeneity of niobium metal is essentially important for good performance. CBMM constantly strives to improve process controls and product quality, and is currently implementing innovations in production, research and development to further improve ingot quality. The main aim is to reduce the content of interstitial elements, such as nitrogen (N), oxygen (O), carbon (C), and hydrogen (H), starting with the raw materials through the final step of ingot production. CBMM held the first trial to produce the world’s largest-diameter niobium ingot (as cast 535 mm). The results of this initial trial presented very low levels of interstitial impurities (N, O, C, H), allowing the achievement of residual resistivity ratio (RRR) values very close to 300 in a six-melt process in an electron beam furnace. These values were reached with 850 ppm of tantalum. SRF cavities will be produced with this material in order to study the effect of low impurities and high RRR on the Q factor and accelerating gradient.

  6. Portable High Sensitivity and High Resolution Sensor to Determine Oxygen Purity Levels Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The objective of this Phase I STTR project is to develop a highly sensitive oxygen (O2) sensor, with high accuracy and precision, to determine purity levels of high...

  7. HIGH-PURITY WATER PRODUCTION BY RO/EDI SYSTEM

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    @@ Electrodeionization(EDI),also known as continuous deionization(CDI)and packed-cell electrodialysis,is a novel hybrid separation process combining ion-exchange resin with ion-exchange membrane in one unit.The EDI process was discovered in the 1950's[1,2]in laboratory,the first commercial apparatus for the production of high-purity water was available in 1987[3].Now the EDI technology has been found and will be continuously found its great applications in many engineering fields. In EDI,the dilute compartments are filled with mixed-bed ion-exchange resins,which enhance the transport to the membranes under the force of a direct current.The ion transport is almost entire through the ion-exchange resins and is not effected through the water.Under certain conditions,water-splitting reaction occurs in the dilute chambers and then the relative high concentrations of H+ and OH- are able to regenerate the resins continuously, With the unique “electroregeneration",the EDI unit can be considered as a mixed-bed ion-exchange column with continuous regeneration.and therefore is capable of deep deionization.Comparing with electrodialysis and ion exchange respectively,EDI has put up much superiority in water desalination. In our experiments,the processes for production of high-purity water from tap water are consisted of pretreatment (with ultrafiltration,active carbon and 10 μm-filtration),RO and EDI.

  8. Characteristics of GRIFFIN high-purity germanium clover detectors

    Science.gov (United States)

    Rizwan, U.; Garnsworthy, A. B.; Andreoiu, C.; Ball, G. C.; Chester, A.; Domingo, T.; Dunlop, R.; Hackman, G.; Rand, E. T.; Smith, J. K.; Starosta, K.; Svensson, C. E.; Voss, P.; Williams, J.

    2016-06-01

    The Gamma-Ray Infrastructure For Fundamental Investigations of Nuclei, GRIFFIN, is a new experimental facility for radioactive decay studies at the TRIUMF-ISAC laboratory. The performance of the 16 high-purity germanium (HPGe) clover detectors that will make up the GRIFFIN spectrometer is reported. The energy resolution, efficiency, timing resolution, crosstalk and preamplifier properties of each crystal were measured using a combination of analog and digital data acquisition techniques. The absolute efficiency and add-back factors are determined for the energy range of 80-3450 keV. The detectors show excellent performance with an average over all 64 crystals of a FWHM energy resolution of 1.89(6) keV and relative efficiency with respect to a 3 in . × 3 in . NaI detector of 41(1)% at 1.3 MeV.

  9. Development of high purity niobium used in SRF accelerating cavity

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Niobium is widely used in SRF(Superconducting Radio Frequency)cavities due to its excellent superconductivity and workability.With the continuous development of technology,higher demands of material are raised.One of the key issues is that RRR(Residual Resistance Ratio)of the Nb material should be more than 300.which requires that the Nb ingot have even higher RRR.This article introduces the development and the experimental results of high purity niobium in OTIC in Ningxia(Ningxia Orient Tantalum Industry Co.Ltd.),and the test results of the single cell TESLA(Tera Electron volt energy Superconducting Linear Accelerator)shaped cavity manufactured by Peking University using Nb material from OTIC.

  10. Cube orientation in hot rolled high purity aluminum plate

    Institute of Scientific and Technical Information of China (English)

    杨平; 毛卫民

    2003-01-01

    X-ray diffraction and orientation mapping in EBSD measurement were applied to obtain information ofdeformation and recrystallization with the emphasis on the cube orientation in hot rolled high purity aluminumplates. It is shown that cube orientations are retained to a large extent during hot rolling. Some deformed cubegrains are found to have experienced large extent of recovery according to their Kikuchi band contrasts. The de-formed cube-oriented grains in hot rolled plates are in an unfavorite growth condition with respect to their neighbor-ing grain orientations for the subsequent annealing. The reasons for the phenomena observed, as well as the influ-ence of hot rolling process on subsequent cold rolling and final annealing were discussed.

  11. A TNFR2-Agonist Facilitates High Purity Expansion of Human Low Purity Treg Cells.

    Directory of Open Access Journals (Sweden)

    Xuehui He

    Full Text Available Regulatory T cells (Treg are important for immune homeostasis and are considered of great interest for immunotherapy. The paucity of Treg numbers requires the need for ex vivo expansion. Although therapeutic Treg flow-sorting is feasible, most centers aiming at Treg-based therapy focus on magnetic bead isolation of CD4+CD25+ Treg using a good manufacturing practice compliant closed system that achieves lower levels of cell purity. Polyclonal Treg expansion protocols commonly use anti-CD3 plus anti-CD28 monoclonal antibody (mAb stimulation in the presence of rhIL-2, with or without rapamycin. However, the resultant Treg population is often heterogeneous and pro-inflammatory cytokines like IFNγ and IL-17A can be produced. Hence, it is crucial to search for expansion protocols that not only maximize ex vivo Treg proliferative rates, but also maintain Treg stability and preserve their suppressive function. Here, we show that ex vivo expansion of low purity magnetic bead isolated Treg in the presence of a TNFR2 agonist mAb (TNFR2-agonist together with rapamycin, results in a homogenous stable suppressive Treg population that expresses FOXP3 and Helios, shows low expression of CD127 and hypo-methylation of the FOXP3 gene. These cells reveal a low IL-17A and IFNγ producing potential and hardly express the chemokine receptors CCR6, CCR7 and CXCR3. Restimulation of cells in a pro-inflammatory environment did not break the stability of this Treg population. In a preclinical humanized mouse model, the TNFR2-agonist plus rapamycin expanded Treg suppressed inflammation in vivo. Importantly, this Treg expansion protocol enables the use of less pure, but more easily obtainable cell fractions, as similar outcomes were observed using either FACS-sorted or MACS-isolated Treg. Therefore, this protocol is of great interest for the ex vivo expansion of Treg for clinical immunotherapy.

  12. A TNFR2-Agonist Facilitates High Purity Expansion of Human Low Purity Treg Cells.

    Science.gov (United States)

    He, Xuehui; Landman, Sija; Bauland, Stijn C G; van den Dolder, Juliette; Koenen, Hans J P M; Joosten, Irma

    2016-01-01

    Regulatory T cells (Treg) are important for immune homeostasis and are considered of great interest for immunotherapy. The paucity of Treg numbers requires the need for ex vivo expansion. Although therapeutic Treg flow-sorting is feasible, most centers aiming at Treg-based therapy focus on magnetic bead isolation of CD4+CD25+ Treg using a good manufacturing practice compliant closed system that achieves lower levels of cell purity. Polyclonal Treg expansion protocols commonly use anti-CD3 plus anti-CD28 monoclonal antibody (mAb) stimulation in the presence of rhIL-2, with or without rapamycin. However, the resultant Treg population is often heterogeneous and pro-inflammatory cytokines like IFNγ and IL-17A can be produced. Hence, it is crucial to search for expansion protocols that not only maximize ex vivo Treg proliferative rates, but also maintain Treg stability and preserve their suppressive function. Here, we show that ex vivo expansion of low purity magnetic bead isolated Treg in the presence of a TNFR2 agonist mAb (TNFR2-agonist) together with rapamycin, results in a homogenous stable suppressive Treg population that expresses FOXP3 and Helios, shows low expression of CD127 and hypo-methylation of the FOXP3 gene. These cells reveal a low IL-17A and IFNγ producing potential and hardly express the chemokine receptors CCR6, CCR7 and CXCR3. Restimulation of cells in a pro-inflammatory environment did not break the stability of this Treg population. In a preclinical humanized mouse model, the TNFR2-agonist plus rapamycin expanded Treg suppressed inflammation in vivo. Importantly, this Treg expansion protocol enables the use of less pure, but more easily obtainable cell fractions, as similar outcomes were observed using either FACS-sorted or MACS-isolated Treg. Therefore, this protocol is of great interest for the ex vivo expansion of Treg for clinical immunotherapy.

  13. Differential Diode Laser Sensor for High-Purity Oxygen Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A compact portable sensor for determining the purity of oxygen concentrations near 100 percent is proposed based on differential absorption of two beams from a diode...

  14. Observing bulk diamond spin coherence in high-purity nanodiamonds

    Science.gov (United States)

    Knowles, Helena S.; Kara, Dhiren M.; Atatüre, Mete

    2014-01-01

    Nitrogen-vacancy (NV) centres in diamond are attractive for research straddling quantum information science, nanoscale magnetometry and thermometry. Whereas ultrapure bulk diamond NVs sustain the longest spin coherence times among optically accessible spins, nanodiamond NVs exhibit persistently poor spin coherence. Here we introduce high-purity nanodiamonds accommodating record-long NV coherence times, >60 μs, observed through universal dynamical decoupling. We show that the main contribution to decoherence comes from nearby nitrogen impurities rather than surface states. We protect the NV spin free precession, essential to d.c. magnetometry, by driving solely these impurities into the motional narrowing regime. This extends the NV free induction decay time from 440 ns, longer than that in type Ib bulk diamond, to 1.27 μs, which is comparable to that in type IIa (impurity-free) diamond. These properties allow the simultaneous exploitation of both high sensitivity and nanometre resolution in diamond-based emergent quantum technologies.

  15. The Status Quo and Development Trend of High-purity Gold Sputtering Targets

    Institute of Scientific and Technical Information of China (English)

    YANG Anheng; XIE Hongchao; ZHU Yong

    2012-01-01

    This article gives a brief introduction to manufacturers and markets of sputtering targets as well as the manufacturing technology thereof.Then,it analyzes the application of high-purity gold sputtering targets in the fields of integrated circuit,information storage,flat panel display,etc.Based on the above,the article analyzes the processing development trend for the high-purity gold sputtering targets in aspects of ultra-high purity,manufacturing technology,analysis and testing technologies.

  16. Analytical challenges in characterization of high purity materials

    Indian Academy of Sciences (India)

    K L Ramakumar

    2005-07-01

    Available analytical literature reveals that it is possible to identify a lot of procedures to carry out any determination using a plethora of analytical techniques. The fundamental analytical requirements for realizing the desired and acceptable information from a chemical analysis are representative nature of the sample, precision, accuracy, selectivity and sensitivity. These decide, to a larger extent, the selection of the most appropriate methodology in order to obtain chemical information from a system. A number of analytical methodologies are being used in the author’s laboratory for carrying out trace elemental analysis as a part of chemical quality control. Quite a good number of analytical challenges with specific reference to the characterization of high purity materials of relevance to nuclear technology were addressed and methodologies were developed for trace elemental analysis of both metallic and non-metallic constituents. A brief review of these analytical challenges and the analytical methodologies developed and also the future needs of analytical chemist are presented in this paper.

  17. An optimized protocol for the production of high purity maltose.

    Science.gov (United States)

    Nehete, P N; Shah, N K; Ramamurthy, V; Kothari, R M

    1992-07-01

    An economical protocol, which is simple, rapid and reproducible for the production of maltose by enzymatic hydrolysis of tapioca starch, has been optimized. The protocol involves liquefaction of 35% (w/w) tapioca starch by bacterial α-amylase at 78±2°C to 3 to 5% (w/w) reducing sugars, followed by maximal (85±3% w/w maltose equivalent) saccharification with barley β-amylase and pullulanase at 50°C for 24 to 30 h. The post-saccharification recovery protocol comprised decolourization by charcoal, de-dextrinization by denatured spirit precipitation, de-ionization by passage through cation and anion exchangers and dehydration by vacuum drying. A white crystalline maltose powder was obtained with specifications comparable to commercial high purity maltose. The protocol yields at least 60% (w/w) recovery of maltose and is suitable for use by the pharmaceutical industry. The protocol is unique in that it utilizes cheap and easily hydrolysed tapioca starch, leaves no mother liquor, enabling higher recovery of maltose, and allows almost quantitative recovery of limit maltodextrins, a value-added marketable by-product.

  18. A light hydrocarbon fuel processor producing high-purity hydrogen

    Science.gov (United States)

    Löffler, Daniel G.; Taylor, Kyle; Mason, Dylan

    This paper discusses the design process and presents performance data for a dual fuel (natural gas and LPG) fuel processor for PEM fuel cells delivering between 2 and 8 kW electric power in stationary applications. The fuel processor resulted from a series of design compromises made to address different design constraints. First, the product quality was selected; then, the unit operations needed to achieve that product quality were chosen from the pool of available technologies. Next, the specific equipment needed for each unit operation was selected. Finally, the unit operations were thermally integrated to achieve high thermal efficiency. Early in the design process, it was decided that the fuel processor would deliver high-purity hydrogen. Hydrogen can be separated from other gases by pressure-driven processes based on either selective adsorption or permeation. The pressure requirement made steam reforming (SR) the preferred reforming technology because it does not require compression of combustion air; therefore, steam reforming is more efficient in a high-pressure fuel processor than alternative technologies like autothermal reforming (ATR) or partial oxidation (POX), where the combustion occurs at the pressure of the process stream. A low-temperature pre-reformer reactor is needed upstream of a steam reformer to suppress coke formation; yet, low temperatures facilitate the formation of metal sulfides that deactivate the catalyst. For this reason, a desulfurization unit is needed upstream of the pre-reformer. Hydrogen separation was implemented using a palladium alloy membrane. Packed beds were chosen for the pre-reformer and reformer reactors primarily because of their low cost, relatively simple operation and low maintenance. Commercial, off-the-shelf balance of plant (BOP) components (pumps, valves, and heat exchangers) were used to integrate the unit operations. The fuel processor delivers up to 100 slm hydrogen >99.9% pure with thermal efficiency is

  19. The Hydrometallurgical Extraction and Recovery of High-Purity Silver

    Science.gov (United States)

    Hoffmann, James E.

    2012-06-01

    -bearing inputs, will be described in detail to demonstrate how typical chemical engineering unit process and unit operations have supplanted classic smelting and fire refining techniques. The Kennecott Copper Company, which has operated a hydrometallurgical circuit successfully for the recovery of high-purity silver from the slimes wet chlorination residue, has permitted me to provide some operation information and results using the technology. Both Phelps Dodge and Kennecott should be recognized for their forward-looking attitude in undertaking the conversion of conceptual chemistry into successful, full-scale plants. The process as employed at Phelps Dodge is discussed at length in reference (J.E. Hoffmann and B. Wesstrom: Hydrometallurgy, 1994, vol. 94, pp. 69-105).

  20. A cleaner two-step synthesis of high purity diallyldimethylammonium chloride monomers for flocculant preparation

    Institute of Scientific and Technical Information of China (English)

    TIAN Bing-hui; FAN Bin; PENG Xian-jia; LUAN Zhao-kun

    2005-01-01

    In order to improve the flocculation efficiency of polydiallyldimethylammonium chloride (PDADMAC), high molecular weight PDADMAC should be prepared from high purity diallyldimethylammonium chloride(DADMAC) monomers. In this paper, a cleaner method with microwave irradiation and alkali solidification was proposed for preparing high pure DADMAC by selective heating under low temperature, and the prepared high purity DADMAC is characterized using FTIR and atomic absorption spectrometry. The new method provides a solution to the key technical problem of PDADMAC synthesis. Comparing with the conventional methods, the results showed that the advantages of the novel synthesis include: (a) high purity DADMAC is improved from 57% to 71%; (b) reaction time of tertiary amine preparation is shortened from 6 h to 7 min; (c) water instead of acetone was used as reaction medium; (d) toxic by-products,wastewater and waste gas are eliminated. Flocculant made from the synthesized high purity DADMAC monomers was proved more efficient in flocculation tests.

  1. Properties and Performances of High Purity Corundum Bricks for Chemical and Petrochemical Industries in China

    Institute of Scientific and Technical Information of China (English)

    CHENRen-pin; LINYu-lian; 等

    1995-01-01

    The properties and performances of high purity corundum bricks for the refractory linings of the gasifiers in the ammonia and ethene synthesis and carbon black reaction furnaces in China are described.The high purity corundum bricks are characterized by high refractoriness,hot strength,dimensional stability and chemical inertness at elevated temperature,Their performances in the gasifiers and carbon black furnaces are very satisfied ,The failure mechansims of the refractory lining are discussed on the basis of the petrographic analysis.

  2. High spectral purity Kerr frequency comb radio frequency photonic oscillator.

    Science.gov (United States)

    Liang, W; Eliyahu, D; Ilchenko, V S; Savchenkov, A A; Matsko, A B; Seidel, D; Maleki, L

    2015-08-11

    Femtosecond laser-based generation of radio frequency signals has produced astonishing improvements in achievable spectral purity, one of the basic features characterizing the performance of an radio frequency oscillator. Kerr frequency combs hold promise for transforming these lab-scale oscillators to chip-scale level. In this work we demonstrate a miniature 10 GHz radio frequency photonic oscillator characterized with phase noise better than -60 dBc Hz(-1) at 10 Hz, -90 dBc Hz(-1) at 100 Hz and -170 dBc Hz(-1) at 10 MHz. The frequency stability of this device, as represented by Allan deviation measurements, is at the level of 10(-10) at 1-100 s integration time-orders of magnitude better than existing radio frequency photonic devices of similar size, weight and power consumption.

  3. Depletion of gadolinium burnable poison in a PWR assembly with high burnup fuel

    Energy Technology Data Exchange (ETDEWEB)

    Refeat, Riham Mahmoud [Nuclear and Radiological Regulatory Authority (NRRA), Cairo (Egypt). Safety Engineering Dept.

    2015-12-15

    A tendency to increase the discharge burnup of nuclear fuel for Advanced Pressurized Water Reactors (PWR) has been a characteristic of its operation for many years. It will be able to burn at very high burnup of about 70 GWd/t with UO{sub 2} fuels. The U-235 enrichment must be higher than 5 %, which leads to the necessity of using an extremely efficient burnable poison like Gadolinium oxide. Using gadolinium isotope is significant due to its particular depletion behavior (''Onion-Skin'' effect). In this paper, the MCNPX2.7 code is used to calculate the important neutronic parameters of the next generation fuels of PWR. K-infinity, local peaking factor and fission rate distributions are calculated for a PWR assembly which burn at very high burnup reaching 70 GWd/t. The calculations are performed using the recently released evaluated Gadolinium cross section data. The results obtained are close to those of a LWR next generation fuel benchmark problem. This demonstrates that the calculation scheme used is able to accurately model a PWR assembly that operates at high burnup values.

  4. First measurements with new high-resolution gadolinium-GEM neutron detectors

    CERN Document Server

    AUTHOR|(CDS)2070256; Birch, Jens; Etxegarai, Maddi; Hall-Wilton, Richard; Höglund, Carina; Hultman, Lars; Llamas-Jansa, Isabel; Oliveri, Eraldo; Oksanen, Esko; Robinson, Linda; Ropelewski, Leszek; Schmidt, Susann; Streli, Christina; Thuiner, Patrik

    2016-01-01

    European Spallation Source instruments like the macromolecular diffractometer, NMX, require an excellent neutron detection efficiency, high-rate capabilities, time resolution, and an unprecedented spatial resolution in the order of a few hundred micrometers over a wide angular range of the incoming neutrons. For these instruments solid converters in combination with Micro Pattern Gaseous Detectors (MPGDs) are a promising option. A GEM detector with gadolinium converter was tested on a cold neutron beam at the IFE research reactor in Norway. The {\\mu}TPC analysis, proven to improve the spatial resolution in the case of $^{10}$B converters, is extended to gadolinium based detectors. For the first time, a Gd-GEM was successfully operated to detect neutrons with an estimated efficiency of 10% at a wavelength of 2 {\\AA} and a position resolution better than 350 {\\mu}m.

  5. First measurements with new high-resolution gadolinium-GEM neutron detectors

    Science.gov (United States)

    Pfeiffer, D.; Resnati, F.; Birch, J.; Etxegarai, M.; Hall-Wilton, R.; Höglund, C.; Hultman, L.; Llamas-Jansa, I.; Oliveri, E.; Oksanen, E.; Robinson, L.; Ropelewski, L.; Schmidt, S.; Streli, C.; Thuiner, P.

    2016-05-01

    European Spallation Source instruments like the macromolecular diffractometer (NMX) require an excellent neutron detection efficiency, high-rate capabilities, time resolution, and an unprecedented spatial resolution in the order of a few hundred micrometers over a wide angular range of the incoming neutrons. For these instruments solid converters in combination with Micro Pattern Gaseous Detectors (MPGDs) are a promising option. A GEM detector with gadolinium converter was tested on a cold neutron beam at the IFE research reactor in Norway. The μTPC analysis, proven to improve the spatial resolution in the case of 10B converters, is extended to gadolinium based detectors. For the first time, a Gd-GEM was successfully operated to detect neutrons with a measured efficiency of 11.8% at a wavelength of 2 Åand a position resolution better than 250 μm.

  6. Determination of Trace Elements in High Purity Gold by High Resolution Inductively Coupled Plasma Mass Spectrometry

    Institute of Scientific and Technical Information of China (English)

    XIE Hualin; HUANG Kelong; NIE Xidu; FU Liang

    2009-01-01

    Trace elements were determined in high purity gold by high resolution inductively coupled plasma mass spectrometry(HR-ICP-MS).Sample were decomposed by aqua regia.To overcome some potentially problematic spectral interference,measurements were acquired in both medium and high resolution modes.The matrix effects due to the presence of excessive HCl and Au were evaluated.The optimum conditions for the determination was tested and discussed.The standard addition method was employed for quantitative analysis.The detection limits range from 0.01 μg/g to 0.28 μg/g depending on the elements.The method is accurate,quick and convenient.It has been applied to the determination of trace elements in high purity gold with satisfactory results.

  7. Spectroscopic Determination of Trace Contaminants in High-Purity Oxygen

    Science.gov (United States)

    Hornung, Steven

    2013-01-01

    Oxygen used for extravehicular activities (EVAs) must be free of contaminants because a difference in a few tenths of a percent of argon or nitrogen content can mean significant reduction in available EVA time. These inert gases build up in the extravehicular mobility unit because they are not metabolized or scrubbed from the atmosphere. A prototype optical emission technique capable of detecting argon and nitrogen below 0.1% in oxygen has been developed. This instrument uses a glow discharge in reduced-pressure gas to produce atomic emission from the species present. Because the atomic emission lines from oxygen, nitrogen, and argon are discrete, and in many cases well-separated, trace amounts of argon and nitrogen can be detected in the ultraviolet and visible spectrum. This is a straightforward, direct measurement of the target contaminants, and may lend itself to a device capable of on-orbit verification of oxygen purity. A glow discharge is a plasma formed in a low-pressure (1 to 10 Torr) gas cell between two electrodes. Depending on the configuration, voltages ranging from 200 V and above are required to sustain the discharge. In the discharge region, the gas is ionized and a certain population is in the excited state. Light is produced by the transitions from the excited states formed in the plasma to the ground state. The spectrum consists of discrete, narrow emission lines for the atomic species, and broader peaks that may appear as a manifold for molecular species such as O2 and N2, the wavelengths and intensities of which are a characteristic of each atom. The oxygen emission is dominated by two peaks at 777 and 844 nm.

  8. Radiochemical purity of Mo and Tc solution obtained after irradiation and dissolution of Mo-100-enriched and ultra-high-purity natural Mo disks

    Energy Technology Data Exchange (ETDEWEB)

    Tkac, Peter [Argonne National Lab. (ANL), Argonne, IL (United States); Gromov, Roman [Argonne National Lab. (ANL), Argonne, IL (United States); Chemerisov, Sergey D. [Argonne National Lab. (ANL), Argonne, IL (United States); Rotsch, David A. [Argonne National Lab. (ANL), Argonne, IL (United States); Vandegrift, George F. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-09-01

    Four irradiations of ultra-high-purity natural Mo targets and one irradiation using 97.4% Mo-100-enriched material were performed. The purpose of these irradiations was to determine whether the presence of Sn stabilizer in the H2O2 used for the dissolution of sintered Mo disks can affect the radiochemical purity of the final K2MoO4 in 5M KOH solution. Results from radiochemical purity tests performed using thin-layer paper chromatography show that even 2– 3× excess of Sn-stabilized H2O2 typically used for dissolution of sintered Mo disks did not affect the radiochemical purity of the final product.

  9. Producing High Priests and Princesses: The Father-Daughter Relationship in the Christian Sexual Purity Movement

    Directory of Open Access Journals (Sweden)

    Elizabeth Gish

    2016-03-01

    Full Text Available This article describes and analyzes father-daughter purity balls in the context of the contemporary U.S. American conservative Christian sexual purity movement, with an emphasis on taking the self-understanding of those involved in the movement into account. It shows the ways that the idealization of a hierarchical father-daughter relationship both constructs and reflects sexual purity ideals. The Christian sexual purity teachings frame this father-daughter relationship as an essential part of forming the ideal subject, and as reflective of the right order of the kingdom of God. In the logic of sexual purity, a good man is the strong high-priest leader of the household and the ideal girl is princess-like: white, non-poor, attractive, pure, feminine, delicate, and receptive. She is preparing, under her father’s guidance, for heterosexual marriage. Attention to the father-daughter relationship in the sexual purity movement highlights the ways that sexual purity is primarily about subject formation and the ordering of relationships—in families, in the nation, and in the church—and less about the specifics of when particular sexual acts take place or the public health risks that might come from those acts. This exploration also brings into relief the ways that contemporary conservative Christian sexual purity teachings draw from and build on two prominent aspects of contemporary U.S. American popular culture: the important role of the princess figure, and the buying of goods as indispensable to the formation of the subject.

  10. Development and validation of a reversed-phase high-performance liquid chromatography method for routine identification and purity assessment of high-purity steviol glycoside sweeteners.

    Science.gov (United States)

    Bililign, Tsion; Moore, Jeffrey C; Tan, Shane; Leeks, Allan T

    2014-02-12

    The widespread application of stevia-based sweeteners in food products has resulted in the need for reliable analytical methods for measuring the purity and identity of high-purity steviol glycoside ingredients. The objective of this research was to develop and validate a new reversed-phase separation method capable of separating and quantifying nine steviol glycosides present in typical high-purity stevia extract ingredients. Results of the study established the linearity of the method at a correlation factor of 1.000 for the two major components and other minor components of this food ingredient. Method accuracy values were in the range of 99.1-100.9%. The percent relative standard deviation for six independent assay determinations was 1.0%. The method was determined to be robust for minor changes in column temperature, initial acetonitrile content, flow rate, and wavelength. The validated high-performance liquid chromatography method was found to be suitable to be included by USP as a Food Chemicals Codex compendial standard for steviol glycosides.

  11. Microstructure Evolution in High Purity Aluminum Single Crystal Processed by Equal Channel Angular Pressing (ECAP).

    Science.gov (United States)

    Dong, Jinfang; Dong, Qing; Dai, Yongbing; Xing, Hui; Han, Yanfeng; Ma, Jianbo; Zhang, Jiao; Wang, Jun; Sun, Baode

    2017-01-22

    Aluminum single crystal with 99.999% purity was deformed at room temperature by equal channel angular pressing (ECAP) up to 16 passes. Grain size and misorientation of processed samples were quantitatively characterized by TEM and EBSD. The results show that the refinement efficiency of high purity aluminum single crystal was poor in the initial stage. Extrusion by fewer ECAP passes (n ≤ 8) resulted in only elongated grains containing a large number of subgrains and small misorientations between grains. Stable microstructures of nearly equiaxed grains with high misorientations were obtained by 15 passages, indicating that the initial extremely coarse grains and highly uniform grain orientation are not conducive to the accumulation of strain energy. The initial state of high purity aluminum has a significant effect on the refining efficiency of the ECAP process.

  12. High-precision efficiency calibration of a high-purity co-axial germanium detector

    Energy Technology Data Exchange (ETDEWEB)

    Blank, B., E-mail: blank@cenbg.in2p3.fr [Centre d' Etudes Nucléaires de Bordeaux Gradignan, UMR 5797, CNRS/IN2P3, Université de Bordeaux, Chemin du Solarium, BP 120, 33175 Gradignan Cedex (France); Souin, J.; Ascher, P.; Audirac, L.; Canchel, G.; Gerbaux, M.; Grévy, S.; Giovinazzo, J.; Guérin, H.; Nieto, T. Kurtukian; Matea, I. [Centre d' Etudes Nucléaires de Bordeaux Gradignan, UMR 5797, CNRS/IN2P3, Université de Bordeaux, Chemin du Solarium, BP 120, 33175 Gradignan Cedex (France); Bouzomita, H.; Delahaye, P.; Grinyer, G.F.; Thomas, J.C. [Grand Accélérateur National d' Ions Lourds, CEA/DSM, CNRS/IN2P3, Bvd Henri Becquerel, BP 55027, F-14076 CAEN Cedex 5 (France)

    2015-03-11

    A high-purity co-axial germanium detector has been calibrated in efficiency to a precision of about 0.15% over a wide energy range. High-precision scans of the detector crystal and γ-ray source measurements have been compared to Monte-Carlo simulations to adjust the dimensions of a detector model. For this purpose, standard calibration sources and short-lived online sources have been used. The resulting efficiency calibration reaches the precision needed e.g. for branching ratio measurements of super-allowed β decays for tests of the weak-interaction standard model.

  13. High-dose gadolinium-enhanced MRI for diagnosis of meningeal metastases

    Energy Technology Data Exchange (ETDEWEB)

    Kallmes, D.F. [Department of Radiology, Box 170, University of Virginia Health Sciences Center, Charlottesville, VA 22908 (United States); Gray, L. [Department of Radiology, Duke University Medical Center, Durham, NC (United States); Glass, J.P. [Department of Medicine, Veterans Administration Hospital, Gainesville, Florida (United States)

    1998-01-01

    We compared high-dose (0.3 mmol/kg) and standard-dose (0.1 mmol/kg) gadolinium-enhanced MRI for diagnosis of meningeal metastases in 12 patients with suspected meningeal metastases. They were imaged with both standard-dose and high-dose gadolinium. All patients with abnormal meningeal enhancement underwent at least one lumbar puncture for cerebrospinal fluid (CSF) cytology, while patients with normal meningeal enhancement were followed clinically. All patients with negative CSF cytology also were followed clinically. A single observer reviewed all the images, with specific attention to the enhancement pattern of the meninges. Abnormal leptomeningeal enhancement was present in three cases, and abnormal pachymeningeal enhancement in three other patients. All of these patients had abnormal CSF analyses. In two of the three cases of abnormal leptomeningeal enhancement the disease was more evident on high-dose than on standard-dose imaging; in one case the abnormal enhancement was visible only on high-dose imaging. In one of the three cases with abnormal pachymeningeal enhancement, the disease was evident prospectively only with high-dose imaging. (orig.) With 3 figs., 10 refs.

  14. Impurity distribution in high purity germanium crystal and its impact on the detector performance

    Science.gov (United States)

    Wang, Guojian; Amman, Mark; Mei, Hao; Mei, Dongming; Irmscher, Klaus; Guan, Yutong; Yang, Gang

    High-purity germanium crystals were grown in a hydrogen atmosphere using the Czochralski method. The axial and radial distributions of impurities in the crystals were measured by Hall effect and Photo-thermal ionization spectroscopy (PTIS). Amorphous semiconductor contacts were deposited on the germanium crystals to make detectors. Three planar detectors were fabricated from three crystals with different net carrier concentrations (1.7, 7.9 and 10x1010 cm-3). We evaluated the electrical and spectral performance of three detectors. Measurements of gamma-ray spectra from 137Cs, 241Am and 60Co sources demonstrate that the detectors have excellent energy resolution. The relationship between the impurities and detector's energy resolution was analyzed. Keywords: High-purity germanium crystal, High-purity germanium detector This work is supported by DOE grant DE-FG02-10ER46709 and the state of South Dakota..

  15. [Simultaneously preparation of grams of high purity tyrosol, crenulatin and salidroside from Rhodiola crenulata].

    Science.gov (United States)

    Luo, Xin; Wang, Xue-jing; Li, Shi-ping; Zhang, Qiao; Zhao, Yi-wu; Huang Wen-zhe; Wang, Zhen-zhong; Xiao, Wei

    2015-04-01

    Tyrosol, crenulatin and salidroside are the main active constituents of Rhodiola crenulata, with extensive pharmacological activities. In the study, grams of high purity tyrosol, crenulatin and salidroside were simultaneously separated from R. crenulata by the first time. Firstly, R. crenulata was extracted by 70% alcohol. Then, with the yields of three compounds as the index, the macroporous resin was optimized. At last, grams of high purity tyrosol, crenulatin and salidroside were isolated by D-101 macroporousresin, purified by column chromatography. Detected by HPLC, the purity of three compounds were higher than 98%. This method has the advantages of simple process and operation, less dosage of organic solvent, highly yield and reproducibility, suitable for the simultaneously preparation of tyrosol, crenulatin and salidroside.

  16. Investigation of active slip systems in high purity single crystal niobium

    Science.gov (United States)

    Baars, Derek

    The superconducting radio-frequency (SRF) community uses high purity niobium to manufacture SRF cavities for a variety of accelerator applications. Cavities are either made from large-grain sheets cut directly from the ingot and formed, or the ingot microstructure is broken down to form polycrystalline sheets or tubes. Reducing the number of costly electron beam welds to assemble the cavities is also desired. A greater understanding of the active slip systems and their relation to subsequent dislocation substructure would be of use in all these areas, to better understand how large grain niobium deforms and to develop more accurate computational models that will aid in the design and use of more cost-effective forming methods. Studies of slip in high-purity niobium suggest that temperature, material purity, and crystal orientation affect which slip systems are active during deformation, though have not examined the somewhat lesser purity niobium used for SRF cavities. As a step toward these goals, two sets of SRF-purity single crystal niobium samples were deformed to 40% strain in tension at room temperature. The first set was cut and welded back together. The second set consisted of deliberately orientated samples that resolved shear stress onto desired slip systems to evaluate different combinations of slip. Determining likely active slip systems was complex, though the evidence suggests that {112} slip may be dominant at yield at room temperature as suggested by theory, though {110} slip could not be ruled out.

  17. Isolation of high-purity anthocyanin mixtures and monomers from blueberries using combined chromatographic techniques.

    Science.gov (United States)

    Wang, Erlei; Yin, Yongguang; Xu, Caina; Liu, Jingbo

    2014-01-31

    Research on the isolation and preparation of anthocyanins has intensified in recent years because of the requirements of quantitative and bioactive analyses. However, simple and effective methods for the scale purification of pure anthocyanins from natural products are rarely reported. In this study, high-purity anthocyanin mixtures and monomers were successfully isolated from wild blueberries using a combination of column chromatography and semi-preparative HPLC. We established an effective elution system to separate high-purity anthocyanin mixtures with aqueous ethanol containing 0.01% HCl first in an Amberlite XAD-7HP column (ethanol/H2O=35:65) and then in a Sephadex LH-20 column (ethanol/H2O=25:75). Crude anthocyanin extracts were isolated using the Amberlite column, and a purity of 32% was obtained based on UV-vis analysis. Three fractions of anthocyanin mixtures were isolated from the crude extracts using the Sephadex column with purities ranging from 59% to 68%. Three pure monomeric anthocyanins of malvidin-3-O-glucoside, petunidin-3-O-glucoside, and delphinidin-3-O-glucoside were also isolated by semi-preparative HPLC and identified by HPLC-DAD-ESI-MS/MS. The purities of these anthocyanins were determined by analytical HPLC and estimated to be 97.7%, 99.3%, and 95.4%, respectively. The results of this study may help promote the purification of anthocyanins from most blueberry varieties as well as from other plant materials.

  18. Growth of high purity semiconductor epitaxial layers by liquid phase epitaxy and their characterization

    Indian Academy of Sciences (India)

    S Dhar

    2005-07-01

    This paper briefly describes our work and the results on the growth of several III–V epitaxial semiconductor materials in high purity form by liquid phase epitaxy (LPE) technique. Various possible sources of impurities in such growth are listed and step-by-step procedures adopted to reduce them are discussed in particular reference to the growth of GaAs layers. The technique of growing very high purity layers by treating the melt with erbium is described for the growth of InGaAs and GaSb layers.

  19. High-Purity Fe3S4 Greigite Microcrystals for Magnetic and Electrochemical Performance

    NARCIS (Netherlands)

    Li, Guowei; Zhang, Baomin; Yu, Feng; Novakova, Alla A.; Krivenkov, Maxim S.; Kiseleva, Tatiana Y.; Chang, Liao; Rao, Jiancun; Polyakov, Alexey O.; Blake, Graeme R.; de Groot, Robert A.; Palstra, Thomas T. M.

    2014-01-01

    High-purity Fe3S4 (greigite) microcrystals with octahedral shape were synthesized via a simple hydrothermal method using a surfactant. The as-prepared samples have the inverse spinel structure with high crystallinity. The saturation magnetization (M-s) reaches 3.74 mu(B) at 5 K and 3.51 mu(B) at roo

  20. Synthesis of high purity metal oxide nanoparticles for optical applications

    Science.gov (United States)

    Baker, C.; Kim, W.; Friebele, E. J.; Villalobos, G.; Frantz, J.; Shaw, L. B.; Sadowski, B.; Fontana, J.; Dubinskii, M.; Zhang, J.; Sanghera, J.

    2014-09-01

    In this paper we present our recent research results in synthesizing various metal oxide nanoparticles for use as laser gain media (solid state as well as fiber lasers) and transparent ceramic windows via two separate techniques, co-precipitation and flame spray pyrolysis. The nanoparticles were pressed into ceramic discs that exhibited optical transmission approaching the theoretical limit and showed very high optical-to-optical lasing slope efficiency. We have also synthesized sesquioxide nanoparticles using a Flame Spray Pyrolysis (FSP) technique that leads to the synthesis of a metastable phase of sesquioxide which allows fabricating excellent optical quality transparent windows with very fine grain sizes. Finally, we present our research in the synthesis of rare earth doped boehmite nanoparticles where the rareearth ion is encased in a cage of aluminum and oxygen to prevent ion-ion proximity and energy transfer. The preforms have been drawn into fibers exhibiting long lifetimes and high laser efficiencies.

  1. Non-iridescent transmissive structural color filter featuring highly efficient transmission and high excitation purity.

    Science.gov (United States)

    Shrestha, Vivek Raj; Lee, Sang-Shin; Kim, Eun-Soo; Choi, Duk-Yong

    2014-05-12

    Nanostructure based color filtering has been considered an attractive replacement for current colorant pigmentation in the display technologies, in view of its increased efficiencies, ease of fabrication and eco-friendliness. For such structural filtering, iridescence relevant to its angular dependency, which poses a detrimental barrier to the practical development of high performance display and sensing devices, should be mitigated. We report on a non-iridescent transmissive structural color filter, fabricated in a large area of 76.2 × 25.4 mm(2), taking advantage of a stack of three etalon resonators in dielectric films based on a high-index cavity in amorphous silicon. The proposed filter features a high transmission above 80%, a high excitation purity of 0.93 and non-iridescence over a range of 160°, exhibiting no significant change in the center wavelength, dominant wavelength and excitation purity, which implies no change in hue and saturation of the output color. The proposed structure may find its potential applications to large-scale display and imaging sensor systems.

  2. Non-iridescent Transmissive Structural Color Filter Featuring Highly Efficient Transmission and High Excitation Purity

    Science.gov (United States)

    Shrestha, Vivek Raj; Lee, Sang-Shin; Kim, Eun-Soo; Choi, Duk-Yong

    2014-05-01

    Nanostructure based color filtering has been considered an attractive replacement for current colorant pigmentation in the display technologies, in view of its increased efficiencies, ease of fabrication and eco-friendliness. For such structural filtering, iridescence relevant to its angular dependency, which poses a detrimental barrier to the practical development of high performance display and sensing devices, should be mitigated. We report on a non-iridescent transmissive structural color filter, fabricated in a large area of 76.2 × 25.4 mm2, taking advantage of a stack of three etalon resonators in dielectric films based on a high-index cavity in amorphous silicon. The proposed filter features a high transmission above 80%, a high excitation purity of 0.93 and non-iridescence over a range of 160°, exhibiting no significant change in the center wavelength, dominant wavelength and excitation purity, which implies no change in hue and saturation of the output color. The proposed structure may find its potential applications to large-scale display and imaging sensor systems.

  3. Characterization of segmented large volume, high purity germanium detectors

    Energy Technology Data Exchange (ETDEWEB)

    Bruyneel, B. [Koeln Univ. (Germany). Inst. fuer Kernphysik

    2006-07-01

    {gamma}-ray tracking in future HPGe arrays like AGATA will rely on pulse shape analysis (PSA) of multiple {gamma}-interactions. For this purpose, a simple and fast procedure was developed which enabled the first full characterization of a segmented large volume HPGe detector. An analytical model for the hole mobility in a Ge crystal lattice was developed to describe the hole drift anisotropy with experimental velocity values along the crystal axis as parameters. The new model is based on the drifted Maxwellian hole distribution in Ge. It is verified by reproducing successfully experimental longitudinal hole anisotropy data. A comparison between electron and hole mobility shows large differences for the longitudinal and tangential velocity anisotropy as a function of the electrical field orientation. Measurements on a 12 fold segmented, n-type, large volume, irregular shaped HPGe detector were performed in order to determine the parameters of anisotropic mobility for electrons and holes as charge carriers created by {gamma}-ray interactions. To characterize the electron mobility the complete outer detector surface was scanned in small steps employing photopeak interactions at 60 keV. A precise measurement of the hole drift anisotropy was performed with 356 keV rays. The drift velocity anisotropy and crystal geometry cause considerable rise time differences in pulse shapes depending on the position of the spatial charge carrier creation. Pulse shapes of direct and transient signals are reproduced by weighting potential calculations with high precision. The measured angular dependence of rise times is caused by the anisotropic mobility, crystal geometry, changing field strength and space charge effects. Preamplified signals were processed employing digital spectroscopy electronics. Response functions, crosstalk contributions and averaging procedures were taken into account implying novel methods due to the segmentation of the Ge-crystal and the digital electronics

  4. Optical levitation of high purity nanodiamonds in vacuum without heating

    CERN Document Server

    Frangeskou, A C; Gines, L; Mandal, S; Williams, O A; Barker, P F; Morley, G W

    2016-01-01

    Levitated nanodiamonds containing nitrogen vacancy centres in high vacuum are a potential test bed for numerous phenomena in fundamental physics. However, experiments so far have been limited to low vacuum due to heating arising from optical absorption of the trapping laser. We show that milling pure diamond creates nanodiamonds that do not heat up as the optical intensity is raised above 700 GW/m$^2$ below 5 mbar of pressure. This advance now means that the level of attainable vacuum for nanodiamonds in optical dipole traps is no longer temperature limited.

  5. Nanodiamond-Gadolinium(III) Aggregates for Tracking Cancer Growth In Vivo at High Field.

    Science.gov (United States)

    Rammohan, Nikhil; MacRenaris, Keith W; Moore, Laura K; Parigi, Giacomo; Mastarone, Daniel J; Manus, Lisa M; Lilley, Laura M; Preslar, Adam T; Waters, Emily A; Filicko, Abigail; Luchinat, Claudio; Ho, Dean; Meade, Thomas J

    2016-12-14

    The ability to track labeled cancer cells in vivo would allow researchers to study their distribution, growth, and metastatic potential within the intact organism. Magnetic resonance (MR) imaging is invaluable for tracking cancer cells in vivo as it benefits from high spatial resolution and the absence of ionizing radiation. However, many MR contrast agents (CAs) required to label cells either do not significantly accumulate in cells or are not biologically compatible for translational studies. We have developed carbon-based nanodiamond-gadolinium(III) aggregates (NDG) for MR imaging that demonstrated remarkable properties for cell tracking in vivo. First, NDG had high relaxivity independent of field strength, a finding unprecedented for gadolinium(III) [Gd(III)]-nanoparticle conjugates. Second, NDG demonstrated a 300-fold increase in the cellular delivery of Gd(III) compared to that of clinical Gd(III) chelates without sacrificing biocompatibility. Further, we were able to monitor the tumor growth of NDG-labeled flank tumors by T1- and T2-weighted MR imaging for 26 days in vivo, longer than was reported for other MR CAs or nuclear agents. Finally, by utilizing quantitative maps of relaxation times, we were able to describe tumor morphology and heterogeneity (corroborated by histological analysis), which would not be possible with competing molecular imaging modalities.

  6. High Relaxivity Gadolinium Hydroxypyridonate-Viral Capsid Conjugates: Nano-sized MRI Contrast Agents

    Energy Technology Data Exchange (ETDEWEB)

    Meux, Susan C.; Datta, Ankona; Hooker, Jacob M.; Botta, Mauro; Francis, Matthew B.; Aime, Silvio; Raymond, Kenneth N.

    2007-08-29

    High relaxivity macromolecular contrast agents based on the conjugation of gadolinium chelates to the interior and exterior surfaces of MS2 viral capsids are assessed. The proton nuclear magnetic relaxation dispersion (NMRD) profiles of the conjugates show up to a five-fold increase in relaxivity, leading to a peak relaxivity (per Gd{sup 3+} ion) of 41.6 mM{sup -1}s{sup -1} at 30 MHz for the internally modified capsids. Modification of the exterior was achieved through conjugation to flexible lysines, while internal modification was accomplished by conjugation to relatively rigid tyrosines. Higher relaxivities were obtained for the internally modified capsids, showing that (1) there is facile diffusion of water to the interior of capsids and (2) the rigidity of the linker attaching the complex to the macromolecule is important for obtaining high relaxivity enhancements. The viral capsid conjugated gadolinium hydroxypyridonate complexes appear to possess two inner-sphere water molecules (q = 2) and the NMRD fittings highlight the differences in the local motion for the internal ({tau}{sub RI} = 440 ps) and external ({tau}{sub RI} = 310 ps) conjugates. These results indicate that there are significant advantages of using the internal surface of the capsids for contrast agent attachment, leaving the exterior surface available for the installation of tissue targeting groups.

  7. Recovery of high purity precious metals from printed circuit boards.

    Science.gov (United States)

    Park, Young Jun; Fray, Derek J

    2009-05-30

    Waste printed circuit boards (WPCB) have an inherent value because of the precious metal content. For an effective recycling of WPCB, it is essential to recover the precious metals. This paper reports a promising method to recover the precious metals. Aqua regia was used as a leachant and the ratio between metals and leachant was fixed at 1/20 (g/ml). Silver is relatively stable so the amount of about 98 wt.% of the input was recovered without an additional treatment. Palladium formed a red precipitate during dissolution, which were consisted of Pd(NH(4))(2)Cl(6). The amount precipitated was 93 wt.% of the input palladium. A liquid-liquid extraction with toluene was used to extract gold selectively. Also, dodecanethiol and sodium borohydride solution were added to make gold nanoparticles. Gold of about 97 wt.% of the input was recovered as nanoparticles which was identified with a high-resolution transmission electron microscopy through selected area electron diffraction and nearest-neighbor lattice spacing.

  8. Variation of low temperature internal friction of microplastic deformation of high purity molybdenum single crystals

    Energy Technology Data Exchange (ETDEWEB)

    Pal-Val, P.P. (AN Ukrainskoj SSR, Kharkov. Fiziko-Tekhnicheskij Inst. Nizkikh Temperatur); Kaufmann, H.J. (Akademie der Wissenschaften der DDR, Berlin)

    1984-08-01

    Amplitude and temperature spectra of ultrasound absorption in weakly deformed high purity molybdenum single crystals of different orientations were measured. The results were discussed in terms of parameter changes related to quasiparticle or dislocation oscillations, respectively, dislocation point defect interactions as well as defect generation at microplastic deformation.

  9. Crystallographic Analysis of Nucleation at Hardness Indentations in High-Purity Aluminum

    DEFF Research Database (Denmark)

    Xu, Chaoling; Zhang, Yubin; Lin, Fengxiang

    2016-01-01

    Nucleation at Vickers hardness indentations has been studied in high-purity aluminum cold-rolled 12 pct. Electron channeling contrast was used to measure the size of the indentations and to detect nuclei, while electron backscattering diffraction was used to determine crystallographic orientations...

  10. Scalable preparation of high purity rutin fatty acid esters following enzymatic synthesis

    DEFF Research Database (Denmark)

    Lue, Bena-Marie; Guo, Zheng; Xu, Xuebing

    2010-01-01

    Investigations into expanded uses of modified flavonoids are often limited by the availability of these high purity compounds. As such, a simple, effective and relatively fast method for isolation of gram quantities of both long and medium chain fatty acid esters of rutin following scaled-up bios...

  11. Production of high-purity radium-223 from legacy actinium-beryllium neutron sources.

    Science.gov (United States)

    Soderquist, Chuck Z; McNamara, Bruce K; Fisher, Darrell R

    2012-07-01

    Radium-223 is a short-lived alpha-particle-emitting radionuclide with potential applications in cancer treatment. Research to develop new radiopharmaceuticals employing (223)Ra has been hindered by poor availability due to the small quantities of parent actinium-227 available world-wide. The purpose of this study was to develop innovative and cost-effective methods to obtain high-purity (223)Ra from (227)Ac. We obtained (227)Ac from two surplus actinium-beryllium neutron generators. We retrieved the actinium/beryllium buttons from the sources and dissolved them in a sulfuric-nitric acid solution. A crude actinium solid was recovered from the solution by coprecipitation with thorium fluoride, leaving beryllium in solution. The crude actinium was purified to provide about 40 milligrams of actinium nitrate using anion exchange in methanol-water-nitric acid solution. The purified actinium was then used to generate high-purity (223)Ra. We extracted (223)Ra using anion exchange in a methanol-water-nitric acid solution. After the radium was separated, actinium and thorium were then eluted from the column and dried for interim storage. This single-pass separation produces high purity, carrier-free (223)Ra product, and does not disturb the (227)Ac/(227)Th equilibrium. A high purity, carrier-free (227)Th was also obtained from the actinium using a similar anion exchange in nitric acid. These methods enable efficient production of (223)Ra for research and new alpha-emitter radiopharmaceutical development.

  12. Fused salt processing of impure plutonium dioxide to high-purity plutonium metal

    Energy Technology Data Exchange (ETDEWEB)

    Mullins, L.J.; Christensen, D.C.; Babcock, B.R.

    1982-01-01

    A process for converting impure plutonium dioxide (approx. 96% pure) to high-purity plutonium metal (>99.9%) was developed. The process consists of reducing the oxide to an impure plutonium metal intermediate with calcium metal in molten calcium chloride. The impure intermediate metal is cast into an anode and electrorefined to produce high-purity plutonium metal. The oxide reduction step is being done now on a 0.6-kg scale with the resulting yield being >99.5%. The electrorefining is being done on a 4.0-kg scale with the resulting yield being 80 to 85%. The purity of the product, which averages 99.98%, is essentially insensitive to the purity of the feed metal. The yield, however, is directly dependent on the chemical composition of the feed. To date, approximately 250 kg of impure oxide has been converted to pure metal by this processing sequence. The availability of impure plutonium dioxide, together with the need for pure plutonium metal, makes this sequence a valuable plutonium processing tool.

  13. High purity materials as targets for radioisotope production: Needs and challenges

    Indian Academy of Sciences (India)

    V Shivarudrappa; K V Vimalnath

    2005-07-01

    Radionuclides have become powerful and indispensable tools in many endeavours of human activities, most importantly in medicine, industry, biology and agriculture, apart from R&D activities. Ready availability of radionuclides in suitable radiochemical form, its facile detection and elegant tracer concepts are responsible for their unprecedented use. Application of radioisotopes in medicine has given birth to a new branch, viz. nuclear medicine, wherein radioisotopes are used extensively in the diagnosis and treatment of variety of diseases including cancer. Artificial transmutation of an element employing thermal neutrons in a reactor or high energy particle accelerators (cyclotrons) are the routes of radioisotope production world over. Availability of high purity target materials, natural or enriched, are crucial for any successful radioisotope programme. Selection of stable nuclides in suitable chemical form as targets with desired isotopic and chemical purity are among the important considerations in radioisotope production. Mostly the oxide, carbonate or the metal itself are the preferred target forms for neutron activation in a research reactor. Chemical impurities, particularly from the elements of the same group, put a limitation on the purity of the final radioisotope product. Whereas the isotopic impurities result in the production of undesirable radionuclidic impurities, which affect their effective utilization. Isotope Group, BARC, is in the forefront of radioisotope production and supply in the country, meeting demands for gamut of radioisotope applications indigenously for over four decades now. Radioisotopes such as 131I, 99Mo, 32P, 51Cr, 153Sm, 82Br, 203Hg, 198Au etc are produced in TBq quantities every month and supplied to several users and to Board of Radiation and Isotope Technology (BRIT). Such a large production programme puts a huge demand on the reliable sources of availability of high purity target materials which are at present mostly met

  14. Preparation and Characterization of High Purity Enriched10B Boric Acid via Anti-Solvent Recrystallization

    Institute of Scientific and Technical Information of China (English)

    张卫江; 刘天雨; 徐姣

    2016-01-01

    Self-made enriched10B boric acid as raw material was purified by recrystallization. The effects of final crystallization temperature, crystallization time, stirring speed, crystallization frequency and other factors on the purity were investigated. The appropriate operating condition was that the final crystallization temperature and time were 5,℃and 10 h respectively under a low-speed stirring for crystallizing twice, which would make the purity and yield of boric acid reach 99.94% and 95.36%, respectively. Taking this as foundation, recrystallization process was optimized with acetone as anti-solvent, whose amount was the most important index. The boric acid solution was added into acetone and recrystallized under the same condition, and the purity and yield of boric acid would reach 99.98% and 99.61%, respectively. The product detected by XRD was confirmed as boric acid crystal. Main ion concentration in the product was detected by ICP, which basically met the national standard of high purity. Crystal morphology of boric acid was observed by SEM.

  15. Preparation and characterization of (10)B boric acid with high purity for nuclear industry.

    Science.gov (United States)

    Zhang, Weijiang; Liu, Tianyu; Xu, Jiao

    2016-01-01

    Boric acid is often added into coolant as neutron capture agent for pressurized water reactor, whose amount is influenced by its abundance and purity. Therefore, the preparation of enriched (10)B boric acid with high purity is beneficial to nuclear industry. (10)B is also used in developing tumor-specific boronated drugs in boron neutron capture therapy. The boronated drug can be administered to patient intravenously, intratumorally, or deposited at tumor site in surgical excision. Thus, enriched (10)B boric acid is of practical significance in the field of medicine. Self-made boron trifluoride-methanol-complex solution was selected as one of the experimental reagents, and the preparation of (10)B acid was realized by one-step reaction for the complexes with water and calcium chloride. The determination of electrical conductivity in reaction process proves that the optimum reaction time was 16-20 h. Furthermore, the effect of reaction time, ratio of calcium chloride to complex as well as the amount of water on the purity and yield of boric acid was investigated. Finally, the optimum reaction time was 20 h, the optimal solid-liquid ratio (molar ratio) was 3:1, and the amount of water was 1 L of deionized water for each mol of the complex. H2O2 was added in the reaction process to remove Fe(2+). After recrystallization, IR spectra of (10)B boric acid was measured and compared with standard to verify the product of boric acid. The feasibility of the preparation method was determined by the detection of XRD of boric acid. To observe the morphology by polarizing microscope, crystal structure was obtained. The purity of the final product is 99.95 %, and the yield is 96.47 %. The ion concentration of boric acid accords with the national standard of high purity, which was determined by ICP.

  16. A Study of the Surface Quality of High Purity Copper after Heat Treatment

    CERN Document Server

    Aicheler, M; Atieh, S; Calatroni, S; Riddone, G; Lebet, S; Samoshkin, A

    2011-01-01

    Themanufacturing flow of accelerating structures for the compact linear collider, based on diamond-machined high purity copper components, include several thermal cycles (diffusion bonding, brazing of cooling circuits, baking in vacuum, etc.). The high temperature cycles may be carried out following different schedules and environments (vacuum, reducing hydrogen atmosphere, argon, etc.) and develop peculiar surface topographies which have been the object of extended observations. This study presents and discusses the results of scanning electron microscopy (SEM) and optical microscopy investigations.

  17. Simultaneously Recovering High-Purity Chromium and Removing Organic Pollutants from Tannery Effluent

    OpenAIRE

    Jie Zong; Yan-Chun Li; Kang Hu

    2016-01-01

    Chromium pollution is a serious issue because of carcinogenic toxicities of the pollutants and low recovery rate of chromium because of the presence of organic, such as protein and fat. In this work, high recovery rate and high purity of the chromium ion were successfully prepared by the way of acid enzyme, flocculant, and Fenton oxidation. The experiments were characterized by TG, TOC, UV-VIS, and SEM. In the work, the tannery waste chrome liquor was used as experimental material. The result...

  18. Preparation and Characterization of High-Purity Metal Fluorides for Photonic Applications

    Science.gov (United States)

    2011-01-01

    Photonics Technol. Lett., 4 446–8 (1992). 8D. F. Anderson, “ Cerium Fluoride – A Scintillator for High-Rate Applica- tions,” Nucl. Instrum. Meth. Phys... Cerium Doped Heavy Metal Fluoride Glasses, a Possible Alternative for Electromagnetic Calorimetry,” Instrum. Meth. Phys. Res. A, 380, 524–36 (1996). 10J...Preparation and Characterization of High-Purity Metal Fluorides for Photonic Applications* Wendy M. Patterson,‡,† Peter C. Stark,§ Thomas M. Yoshida

  19. Production of solar grade silicon in an arc furnace using high purity starting materials

    Science.gov (United States)

    Aulich, H. A.; Dietze, W.; Eisenbith, K.-H.; Schafer, J.; Schulze, F. W.; Urbach, H.-P.

    Solar cell-grade Si has been produced, using high purity SiO2 and C raw materials, by means of carbothermic reduction. The process involves the production of glass fibers from a melt of ordinary silica sand and glass-forming oxides, whose impurities are then leached out through treatment of the fibers with hot HCl. The high purity carbon is also prepared by treating carbon black with hot HCl. The purified SiO2 and C materials are reacted in an arc surface, yielding Si impurity concentrations corresponding to those of the highly purified materials. A three-phase, 550 kVA-arc furnace was constructed to prepare Si on a large scale.

  20. The European Expression Of Interest For High Purity U-233 Materials

    Energy Technology Data Exchange (ETDEWEB)

    Giaquinto, Joseph M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Younkin, James R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-04-01

    The purpose of this letter report is to document the response for an Expression of Interest (EOI) sent to the European Safeguards and research and development (R&D) scientific communities for the distribution of small amounts of high purity 233U materials for use in safeguards, nonproliferation, and basic R&D in the nuclear disciplines. The intent for the EOI was to gauge the level of international interest for these materials from government and research institutions with programmatic missions in the nuclear security or nuclear R&D arena. The information contained herein is intended to provide information to assist key decision makers in DOE as to the ultimate disposition path for the high purity materials currently being recovered at Oak Ridge National Laboratory (ORNL) and only those items for which there is no United States (U.S.) sponsor identified.

  1. Electrolysis Process of High Purity Gold%高纯金的电解工艺

    Institute of Scientific and Technical Information of China (English)

    叶跃威

    2014-01-01

    介绍了遂昌金矿有限公司的高纯金电解工艺。实践表明,采用该工艺,在金阳极板含金95%~99%下经过一次金电解,金纯度即可达到99.997%以上。经检测,杂质含量低于高纯金(99.999%)的杂质要求。%The high-purity gold electrolysis process of Suichang Gold Mine Co. Ltd., is introduced. The production practice showed that, the content of gold can reach above 99.997% after only one cycle of electrolysis from the anode plate which contains 95%~99% gold. The test results showed that the impurities accord with the requirement of Chinese national standard of high-purity gold (99.999%).

  2. Characterization of Rod-like High-purity Fluorapatite Nanopowders Obtained by Sol-gel Method

    Directory of Open Access Journals (Sweden)

    Nasrin Sasani

    2013-12-01

    Full Text Available high purity fluorapatite (FA with rod-like and spherical-like morphology was synthesized via sol-gel method. Chemical characterization of FA powders was done by XRD and FTIR analyses. Crystallite samples were calculated using Scherer method. Morphology of FA powders was investigated with TEM and SEM images. The results revealed that increasing the time of hydrolysis of phosphate sols significantly decreased the gelation time of FA sols. Also, mixing temperature of P and Ca sols affects the gelation time of samples and increasing pH decreases the gelation time of FA sols. Morphological and chemical characterization of samples showed that the FA powders have high purity and rod-like and spherical-like morphology.

  3. Fabrication of novel cryomill for synthesis of high purity metallic nanoparticles

    Science.gov (United States)

    Kumar, Nirmal; Biswas, Krishanu

    2015-08-01

    The successful preparation of free standing metal nanoparticles with high purity in bulk quantity is the pre-requisite for any potential application. This is possible by using ball milling at cryogenic temperature. However, the most of ball mills available in the market do not allow preparing high purity metal nanoparticles by this route. In addition, it is not possible to carry out in situ measurements of process parameters as well as diagnostic of the process. In the present investigation, we present a detailed study on the fabrication of a cryomill, which is capable of avoiding contaminations in the product. It also provides in situ measurements and diagnostic of the low temperature milling process. Online monitoring of the milling temperature and observation of ball motion are the important aspects in the newly designed mill. The nanoparticles prepared using this fabricated mill have been found to be free standing and also free from contaminations.

  4. Impurity distribution and reduction behaviour of quartz in the production of high purity silicon

    OpenAIRE

    Dal Martello, Elena

    2012-01-01

    The production of solar grade silicon is based on the use of expensive high purity carbon and quartz feedstock as well as various silicon refining techniques. Impurities in the feedstock materials enter the silicon during the carbothermic reduction of quartz. The knowledge of the impurity distribution/removal in the feedstock and in the carbothermic reduction process is necessary for targeting less pure and cheaper raw materials.The aim of the present study is to investigate the impurity dist...

  5. Determination of Trace Iron in High Purity Sodium Fluoride by Graphite Furnace Atomic Absorption Spectrometry

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    A method is described for the direct determination of iron in high purity sodium fluoride using graphite furnace atomic absorption spectrometry. Interferences caused by the matrix are investigated. It is shown that the ashing temperature can be increased to 1 400°C and matrix interferences eliminated, the sensi tivity of iron increased in 1.27 fold by the addition of nickel nitrate. The method is applied to the determina tion of iron in sodium fluoride and satisfactory results are obtained.

  6. Obtaining water with a high degree of purity by using reverse osmosis

    Directory of Open Access Journals (Sweden)

    Nicolae Chirilă

    2011-12-01

    Full Text Available In this paper, we used the method of reverse osmosis in order to obtain water with a high degree of purity. For this aim, we used the TKA 20-120ECO device. We completed physic-chemical determinations for the water of supply, as well as for the water obtained after the osmosis process. The results that we obtained are relevant and interesting.

  7. Aluminium. II - A review of deformation properties of high purity aluminium and dilute aluminium alloys.

    Science.gov (United States)

    Reed, R. P.

    1972-01-01

    The elastic and plastic deformation behavior of high-purity aluminum and of dilute aluminum alloys is reviewed. Reliable property data, including elastic moduli, elastic coefficients, tensile, creep, fatigue, hardness, and impact are presented. Single crystal tensile results are discussed. Rather comprehensive reference lists, containing publications of the past 20 years, are included for each of the above categories. Defect structures and mechanisms responsible for mechanical behavior are presented. Strengthening techniques (alloys, cold work, irradiation, quenching, composites) and recovery are briefly reviewed.

  8. Effect of high-temperature heat treatment duration on the purity and microstructure of MWCNTs

    Indian Academy of Sciences (India)

    I Srikanth; N Padmavathi; P S R Prasad; P Ghosal; R K Jain; Ch Subrahmanyam

    2016-02-01

    The effect of high-temperature heat treatment on purity and structural changes of multiwalled carbon nanotubes (MWCNTs) were studied by subjecting the raw MWCNTs (pristine MWCNTs) to 2600°C for 60 and 120 min. Thermogravimetric analysis (TGA), X-ray diffraction, Raman spectroscopy, transmission electron microscopy (TEM) and scanning electron microscopy (SEM) were used to study the effect of heat-treatment duration on the purity and structural changes of MWCNTs. Results show that high-temperature heat treatment can be used to purify MWCNTs with proper optimization of treatment time. It was observed that 60 min heat treatment of raw MWCNTs imparts high purity and structural perfection to MWCNTs, while 120 min heat treatment imparts structural degradation to MWCNTs with collapse of the innermost shells. The present study indicates that metal impurities act as moderators in controlling the degradation of MWCNTs up to certain duration, and once the metal impurities escape completely, further heat treatment degrades the structure of MWCNTs.

  9. Simple HPLC method for detection of trace ephedrine and pseudoephedrine in high-purity methamphetamine.

    Science.gov (United States)

    Makino, Yukiko

    2012-03-01

    A simple and sensitive HPLC technique was developed for the qualitative determination of ephedrine and pseudoephedrine (ephedrines), used as precursors of clandestine d-methamphetamine hydrochloride of high purity. Good separation of ephedrines from bulk d-methamphetamine was achieved, without any extraction or derivatization procedure on a CAPCELLPACK C18 MGII (250 × 4.6 mm) column. The mobile phase consisted of 50 mM KH2 PO4-acetonitrile (94:6 v/v %) using an isocratic pump system within 20 min for detecting two analytes. One run took about 50 min as it was necessary to wash out overloaded methamphetamine for column conditioning. The analytes were detected by UV absorbance measurement at 210 nm. A sample (20 mg) was simply dissolved in 1 mL of water, and a 50 μL aliquot of the solution was injected into the HPLC. The detection limits for ephedrine and pseudoephedrine in bulk d-methamphetamine were as low as 3 ppm each. This analytical separation technique made it possible to detect ephedrine and/or pseudoephedrine in seven samples of high-purity d-methamphetamine hydrochloride seized in Japan. The presence of trace ephedrines in illicit methamphetamine may strongly indicate a synthetic route via ephedrine in methamphetamine profiling. This method is simple and sensitive, requiring only commonly available equipment, and should be useful for high-purity methamphetamine profiling.

  10. High Purity DNA Extraction with a SPE Microfluidic Chip Using KI as the Binding Salt

    Institute of Scientific and Technical Information of China (English)

    Xing CHEN; Da Fu CUI; Chang Chun LIU

    2006-01-01

    Based on solid phase extraction method, a novel silicon-PDMS-glass microchip for high purity DNA extraction has been developed by using KI as the binding salt. The microfluidic chip fabricated by MEMS technology was composed of a silicon substrate with a coiled channel and a compounded PDMS-glass cover. With this microfluidic chip, the wall of the coiled channel was used as solid phase matrix for binding DNA and DNA was extracted by the fluxion of the binding buffer, washing buffer and elution buffer. KI as a substitute for guanidine, was used successfully as binding salt for purification DNA, obtaining higher purity of genomic DNA and about 13.9 ng DNA from 1 μL rat whole blood in 35 minutes.

  11. Recovery of high-purity metallic Pd from Pd(II)-sorbed biosorbents by incineration.

    Science.gov (United States)

    Won, Sung Wook; Lim, Areum; Yun, Yeoung-Sang

    2013-06-01

    This work reports a direct way to recover metallic palladium with high purity from Pd(II)-sorbed polyethylenimine-modified Corynebacterium glutamicum biosorbent using a combined method of biosorption and incineration. This study is focused on the incineration part which affects the purity of recovered Pd. The incineration temperature and the amount of Pd loaded on the biosorbent were considered as major factors in the incineration process, and their effects were examined. The results showed that both factors significantly affected the enhancement of the recovery efficiency and purity of the recovered Pd. SEM-EDX and XRD analyses were used to confirm that Pd phase existed in the ash. As a result, the recovered Pd was changed from PdO to zero-valent Pd as the incineration temperature was increased from 600 to 900°C. Almost 100% pure metallic Pd was recovered with recovery efficiency above 99.0% under the conditions of 900°C and 136.9 mg/g.

  12. Monte Carlo study of radiation dose enhancement by gadolinium in megavoltage and high dose rate radiotherapy.

    Directory of Open Access Journals (Sweden)

    Daniel G Zhang

    Full Text Available MRI is often used in tumor localization for radiotherapy treatment planning, with gadolinium (Gd-containing materials often introduced as a contrast agent. Motexafin gadolinium is a novel radiosensitizer currently being studied in clinical trials. The nanoparticle technologies can target tumors with high concentration of high-Z materials. This Monte Carlo study is the first detailed quantitative investigation of high-Z material Gd-induced dose enhancement in megavoltage external beam photon therapy. BEAMnrc, a radiotherapy Monte Carlo simulation package, was used to calculate dose enhancement as a function of Gd concentration. Published phase space files for the TrueBeam flattening filter free (FFF and conventional flattened 6MV photon beams were used. High dose rate (HDR brachytherapy with Ir-192 source was also investigated as a reference. The energy spectra difference caused a dose enhancement difference between the two beams. Since the Ir-192 photons have lower energy yet, the photoelectric effect in the presence of Gd leads to even higher dose enhancement in HDR. At depth of 1.8 cm, the percent mean dose enhancement for the FFF beam was 0.38±0.12, 1.39±0.21, 2.51±0.34, 3.59±0.26, and 4.59±0.34 for Gd concentrations of 1, 5, 10, 15, and 20 mg/mL, respectively. The corresponding values for the flattened beam were 0.09±0.14, 0.50±0.28, 1.19±0.29, 1.68±0.39, and 2.34±0.24. For Ir-192 with direct contact, the enhanced were 0.50±0.14, 2.79±0.17, 5.49±0.12, 8.19±0.14, and 10.80±0.13. Gd-containing materials used in MRI as contrast agents can also potentially serve as radiosensitizers in radiotherapy. This study demonstrates that Gd can be used to enhance radiation dose in target volumes not only in HDR brachytherapy, but also in 6 MV FFF external beam radiotherapy, but higher than the currently used clinical concentration (>5 mg/mL would be needed.

  13. Monte Carlo study of radiation dose enhancement by gadolinium in megavoltage and high dose rate radiotherapy.

    Science.gov (United States)

    Zhang, Daniel G; Feygelman, Vladimir; Moros, Eduardo G; Latifi, Kujtim; Zhang, Geoffrey G

    2014-01-01

    MRI is often used in tumor localization for radiotherapy treatment planning, with gadolinium (Gd)-containing materials often introduced as a contrast agent. Motexafin gadolinium is a novel radiosensitizer currently being studied in clinical trials. The nanoparticle technologies can target tumors with high concentration of high-Z materials. This Monte Carlo study is the first detailed quantitative investigation of high-Z material Gd-induced dose enhancement in megavoltage external beam photon therapy. BEAMnrc, a radiotherapy Monte Carlo simulation package, was used to calculate dose enhancement as a function of Gd concentration. Published phase space files for the TrueBeam flattening filter free (FFF) and conventional flattened 6MV photon beams were used. High dose rate (HDR) brachytherapy with Ir-192 source was also investigated as a reference. The energy spectra difference caused a dose enhancement difference between the two beams. Since the Ir-192 photons have lower energy yet, the photoelectric effect in the presence of Gd leads to even higher dose enhancement in HDR. At depth of 1.8 cm, the percent mean dose enhancement for the FFF beam was 0.38±0.12, 1.39±0.21, 2.51±0.34, 3.59±0.26, and 4.59±0.34 for Gd concentrations of 1, 5, 10, 15, and 20 mg/mL, respectively. The corresponding values for the flattened beam were 0.09±0.14, 0.50±0.28, 1.19±0.29, 1.68±0.39, and 2.34±0.24. For Ir-192 with direct contact, the enhanced were 0.50±0.14, 2.79±0.17, 5.49±0.12, 8.19±0.14, and 10.80±0.13. Gd-containing materials used in MRI as contrast agents can also potentially serve as radiosensitizers in radiotherapy. This study demonstrates that Gd can be used to enhance radiation dose in target volumes not only in HDR brachytherapy, but also in 6 MV FFF external beam radiotherapy, but higher than the currently used clinical concentration (>5 mg/mL) would be needed.

  14. Gadolinium oxide nanoplates with high longitudinal relaxivity for magnetic resonance imaging

    Science.gov (United States)

    Cho, Minjung; Sethi, Richa; Ananta Narayanan, Jeyarama Subramanian; Lee, Seung Soo; Benoit, Denise N.; Taheri, Nasim; Decuzzi, Paolo; Colvin, Vicki L.

    2014-10-01

    Molecular-based contrast agents for magnetic resonance imaging (MRI) are often characterized by insufficient relaxivity, thus requiring the systemic injection of high doses to induce sufficient contrast enhancement at the target site. In this work, gadolinium oxide (Gd2O3) nanoplates are produced via a thermal decomposition method. The nanoplates have a core diameter varying from 2 to 22 nm, a thickness of 1 to 2 nm and are coated with either an oleic acid bilayer or an octylamine modified poly(acrylic acid) (PAA-OA) polymer layer. For the smaller nanoplates, longitudinal relaxivities (r1) of 7.96 and 47.2 (mM s)-1 were measured at 1.41 T for the oleic acid bilayer and PAA-OA coating, respectively. These values moderately reduce as the size of the Gd2O3 nanoplates increases, and are always larger for the PAA-OA coating. Cytotoxicity studies on human dermal fibroblast cells documented no significant toxicity, with 100% cell viability preserved up to 250 μM for the PAA-OA coated Gd2O3 nanoplates. Given the 10 times increase in longitudinal relaxivity over the commercially available Gd-based molecular agents and the favorable toxicity profile, the 2 nm PAA-OA coated Gd2O3 nanoplates could represent a new class of highly effective T1 MRI contrast agents.Molecular-based contrast agents for magnetic resonance imaging (MRI) are often characterized by insufficient relaxivity, thus requiring the systemic injection of high doses to induce sufficient contrast enhancement at the target site. In this work, gadolinium oxide (Gd2O3) nanoplates are produced via a thermal decomposition method. The nanoplates have a core diameter varying from 2 to 22 nm, a thickness of 1 to 2 nm and are coated with either an oleic acid bilayer or an octylamine modified poly(acrylic acid) (PAA-OA) polymer layer. For the smaller nanoplates, longitudinal relaxivities (r1) of 7.96 and 47.2 (mM s)-1 were measured at 1.41 T for the oleic acid bilayer and PAA-OA coating, respectively. These values

  15. A prototype High Purity Germanium detector for high resolution gamma-ray spectroscopy at high count rates

    Energy Technology Data Exchange (ETDEWEB)

    Cooper, R.J., E-mail: rjcooper@lbl.gov [Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States); Amman, M.; Luke, P.N. [Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States); Vetter, K. [Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, CA 94720 (United States); Department of Nuclear Engineering, University of California, Berkeley, CA 94720 (United States)

    2015-09-21

    Where energy resolution is paramount, High Purity Germanium (HPGe) detectors continue to provide the optimum solution for gamma-ray detection and spectroscopy. Conventional large-volume HPGe detectors are typically limited to count rates on the order of ten thousand counts per second, however, limiting their effectiveness for high count rate applications. To address this limitation, we have developed a novel prototype HPGe detector designed to be capable of achieving fine energy resolution and high event throughput at count rates in excess of one million counts per second. We report here on the concept, design, and initial performance of the first prototype device.

  16. Gadolinium oxide nanoplates with high longitudinal relaxivity for magnetic resonance imaging.

    Science.gov (United States)

    Cho, Minjung; Sethi, Richa; Narayanan, Jeyarama Subramanian Ananta; Lee, Seung Soo; Benoit, Denise N; Taheri, Nasim; Decuzzi, Paolo; Colvin, Vicki L

    2014-11-21

    Molecular-based contrast agents for magnetic resonance imaging (MRI) are often characterized by insufficient relaxivity, thus requiring the systemic injection of high doses to induce sufficient contrast enhancement at the target site. In this work, gadolinium oxide (Gd2O3) nanoplates are produced via a thermal decomposition method. The nanoplates have a core diameter varying from 2 to 22 nm, a thickness of 1 to 2 nm and are coated with either an oleic acid bilayer or an octylamine modified poly(acrylic acid) (PAA-OA) polymer layer. For the smaller nanoplates, longitudinal relaxivities (r1) of 7.96 and 47.2 (mM s)(-1) were measured at 1.41 T for the oleic acid bilayer and PAA-OA coating, respectively. These values moderately reduce as the size of the Gd2O3 nanoplates increases, and are always larger for the PAA-OA coating. Cytotoxicity studies on human dermal fibroblast cells documented no significant toxicity, with 100% cell viability preserved up to 250 μM for the PAA-OA coated Gd2O3 nanoplates. Given the 10 times increase in longitudinal relaxivity over the commercially available Gd-based molecular agents and the favorable toxicity profile, the 2 nm PAA-OA coated Gd2O3 nanoplates could represent a new class of highly effective T1 MRI contrast agents.

  17. High performance magneto-fluorescent nanoparticles assembled from terbium and gadolinium 1,3-diketones

    Science.gov (United States)

    Zairov, Rustem; Mustafina, Asiya; Shamsutdinova, Nataliya; Nizameev, Irek; Moreira, Beatriz; Sudakova, Svetlana; Podyachev, Sergey; Fattakhova, Alfia; Safina, Gulnara; Lundstrom, Ingemar; Gubaidullin, Aidar; Vomiero, Alberto

    2017-01-01

    Polyelectrolyte-coated nanoparticles consisting of terbium and gadolinium complexes with calix[4]arene tetra-diketone ligand were first synthesized. The antenna effect of the ligand on Tb(III) green luminescence and the presence of water molecules in the coordination sphere of Gd(III) bring strong luminescent and magnetic performance to the core-shell nanoparticles. The size and the core-shell morphology of the colloids were studied using transmission electron microscopy and dynamic light scattering. The correlation between photophysical and magnetic properties of the nanoparticles and their core composition was highlighted. The core composition was optimized for the longitudinal relaxivity to be greater than that of the commercial magnetic resonance imaging (MRI) contrast agents together with high level of Tb(III)-centered luminescence. The tuning of both magnetic and luminescent output of nanoparticles is obtained via the simple variation of lanthanide chelates concentrations in the initial synthetic solution. The exposure of the pheochromocytoma 12 (PC 12) tumor cells and periphery human blood lymphocytes to nanoparticles results in negligible effect on cell viability, decreased platelet aggregation and bright coloring, indicating the nanoparticles as promising candidates for dual magneto-fluorescent bioimaging.

  18. Crystal growth and detector performance of large size high-purity Ge crystals

    CERN Document Server

    Wang, Guojian; Mei, Hao; Mei, Dongming; Irmscher, Klaus; Guan, Yutong; Yang, Gang

    2015-01-01

    High-purity germanium crystals approximately 12 cm in diameter were grown in a hydrogen atmosphere using the Czochralski method. The dislocation density of the crystals was determined to be in the range of 2000 - 4200 cm-2, which meets a requirement for use as a radiation detector. The axial and radial distributions of impurities in the crystals were measured and are discussed. A planar detector was also fabricated from one of the crystals and then evaluated for electrical and spectral performance. Measurements of gamma-ray spectra from Cs-137 and Am-241 sources demonstrate that the detector has excellent energy resolution.

  19. Impurity removal process for high-purity silica production by acid leaching

    Directory of Open Access Journals (Sweden)

    Ezzaouia H.

    2012-06-01

    Full Text Available In our days obtaining silica sand with very high purity is a primordial stage in photovoltaic industry. The effects of acids on the removal of impurity from silica sand have been studied using leaching acids: mixture composed of HF/HCl/H2O with a volume composition of (1:7:24.The obtained material was characterized using Ultraviolet-Visible absorbance (UV-Vis and Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES. Results of the application of this technique show a significant reduction of the amounts of undesirable impurities present in natural silica (such as Co, Fe, Ca, Al, Mg ….

  20. Formation and evolution of tweed structures on high-purity aluminum polycrystalline foils under cyclic tension

    Energy Technology Data Exchange (ETDEWEB)

    Kuznetsov, P. V., E-mail: kpv@ispms.tsc.ru [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation); National Research Tomsk Polytechnic University, Tomsk, 634050 (Russian Federation); Vlasov, I. V. [Institute of Strength Physics and Materials Science SB RAS, Tomsk, 634055 (Russian Federation); Sklyarova, E. A.; Smekalina, T. V. [National Research Tomsk Polytechnic University, Tomsk, 634050 (Russian Federation)

    2015-10-27

    Peculiarities of formation and evolution of tweed structures on the surface of high-purity aluminum polycrystalline foils under cyclic tension were studied using an atom force microscope and a white light interferometer. Tweed structures of micron and submicron sizes were found on the foils at different number of cycles. In the range of 42,000 < N < 95,000 cycles destruction of tweed patterns is observed, which leads to their disappearance from the surface of the foils. Formation of tweed structures of various scales is discussed in terms of the Grinfeld instability.

  1. Formation and evolution of tweed structures on high-purity aluminum polycrystalline foils under cyclic tension

    Science.gov (United States)

    Kuznetsov, P. V.; Vlasov, I. V.; Sklyarova, E. A.; Smekalina, T. V.

    2015-10-01

    Peculiarities of formation and evolution of tweed structures on the surface of high-purity aluminum polycrystalline foils under cyclic tension were studied using an atom force microscope and a white light interferometer. Tweed structures of micron and submicron sizes were found on the foils at different number of cycles. In the range of 42,000 < N < 95,000 cycles destruction of tweed patterns is observed, which leads to their disappearance from the surface of the foils. Formation of tweed structures of various scales is discussed in terms of the Grinfeld instability.

  2. High-purity cobalt thin films with perpendicular magnetic anisotropy prepared by chemical vapor deposition

    Science.gov (United States)

    Ootera, Yasuaki; Shimada, Takuya; Kado, Masaki; Quinsat, Michael; Morise, Hirofumi; Nakamura, Shiho; Kondo, Tsuyoshi

    2015-11-01

    A study of the chemical vapor deposition (CVD) of high-purity cobalt thin films is described. The Co layer prepared by a thermal CVD technique with a Pt/Ta underlayer and a Pt cap layer shows a saturation magnetization (Ms) of ∼1.8 T and perpendicular magnetic anisotropy (PMA) with an anisotropy energy (Ku) of ∼105 J/m3. The cobalt thickness dependence of Ku reveals that the interfacial anisotropy at the Pt/Co interface is most likely the origin of the obtained PMA.

  3. Preparation of high-purity bismuth by sulphur deleadization in vacuum distillation

    Institute of Scientific and Technical Information of China (English)

    熊利芝; 何则强; 刘文萍; 麻成金; 戴永年

    2004-01-01

    The feasibility of separation of impurities in refined bismuth and sulphur deleadization with vacuum distillation was studied theoretically. Experimental studies on sulphur deleadization were carried out under vacuum.The influences of amount of sulphur, distillation temperature, vacuum degree and distillation time on deleadization were investigated and an optimal technical condition was achieved. The content of lead in refined bismuth can be decreased from 30 μg/g to 0.21 μg/g, which has reached the level of "5N" high-purity bismuth. Other impurities in refined bismuth can be also removed effectively under certain conditions.

  4. Practical analysis of high purity chemicals--V. Precision silver chloride gravimetry.

    Science.gov (United States)

    Little, K

    1971-09-01

    A reasonably simple gravimetric silver chloride procedure with fairly wide tolerance in conditions is presented in full detail with all critical steps and precautions delineated. The procedure allows the precision determination of chloride by analysts having limited expertise with exacting gravimetric methods, and can be performed with equipment common to nearly all laboratories and without dependence on a standard substance. The elapsed and actual working times for the assessment of a solid sample in triplicate are 65 and 10-12 hr respectively. The application of the procedure to the assay of some high-purity chloride salts and to the standardization of hydrochloric acid solutions is described.

  5. High-Purity Nickel Prepared by Electron Beam Melting: Purification Mechanism

    Science.gov (United States)

    Zhang, Tao; Shang, Zaiyan; Chen, Ming; He, Jinjiang; Lv, Baoguo; Wang, Xingquan; Xiong, Xiaodong

    2013-12-01

    A bulk cylindrical high-purity nickel ingot, with purity of more than 99.999 pct (5N) in mass, was obtained from the raw nickel with 99.95 pct (3N5) initial purity by virtue of double electron beam melting (EBM). A chemical analysis was performed by using glow discharge mass spectrometry (GDMS) analysis for all elements in the periodic table except carbon, nitrogen, and oxygen, which were tested by the high-performance combustion and fusion method. The major impurities B, Na, Al, Si, P, S, Ca, Ti, Cr, Fe, Cu, Co, Zn, As, Ag, Sb, and Pb showed an excellent removal effect with removal efficiency of more than 85 pct following the double EBMs. Li, Mg, Cl, K, V, Mn, Ga, Ge, Cd, Se, In, Sn, Tl, Au, and Pt were below the detection limit. No significant change in concentration was found for the refractory elements W, Mo, Ta, Nb, and Ir. Be, F, Sc, Se, Br, Rb, Sr, Zr, Y, Ru, Rh, Pd, Te, I, Cs, Ba, La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu, Hf, Re, Os, Hg, Bi, Th, and U were not detectable following the purification as compared to the raw nickel. Gaseous impurities, C, N, O, especially for N, was removed sufficiently. Theoretical calculations for removal efficiency of impurity Fe based on the calculated vapor pressure, activity coefficient, and melt temperature were in good agreement with measured results, and the purification mechanism was ascribed to the evaporation of major impurities and subsequently evacuation by repetitive EBM.

  6. Ultra thin films of gadolinium deposited by evaporation in ultra high vacuum conditions: Composition, growth and morphology

    Energy Technology Data Exchange (ETDEWEB)

    Herrera-Sancho, O.A.; Castro-Gonzalez, D.; Araya-Pochet, J.A. [Centro de Investigacion en Ciencia e Ingenieria de Materiales, Universidad de Costa Rica, 2060 San Pedro, San Jose (Costa Rica); Escuela de Fisica, Universidad de Costa Rica, 2060 San Pedro, San Jose (Costa Rica); Vargas-Castro, W.E., E-mail: william.vargascastro@ucr.ac.cr [Centro de Investigacion en Ciencia e Ingenieria de Materiales, Universidad de Costa Rica, 2060 San Pedro, San Jose (Costa Rica); Escuela de Fisica, Universidad de Costa Rica, 2060 San Pedro, San Jose (Costa Rica)

    2011-02-01

    Ultra-thin gadolinium films with thicknesses between 8 and 101 A were deposited on AT-cut crystalline quartz substrates under ultra high vacuum conditions, and subsequently subjected to composition and morphologic characterization through X-ray photo-spectroscopy analysis and atomic force microscopy. Oxygen contamination is found on the samples, and its amount is estimated in terms of the thickness of an oxygen layer over the gadolinium films after subtracting the contribution to the XPS spectra of the underlying background. Atomic force microscope pictures provide evidence of having metal island films, with two growing regimes: the Volmer-Weber mode for the thinner films considered and the Stranski-Krastanov growing mode for the thicker ones. From evaluation of the sticking coefficient, the shape of the islands is approximated in terms of oblate spheroid caps and variation of the contact angle with film mass thickness is reported.

  7. SIMULTANEOUS PRODUCTION OF HIGH-PURITY HYDROGEN AND SEQUESTRATION-READY CO2 FROM SYNGAS

    Energy Technology Data Exchange (ETDEWEB)

    Linda Denton; Hana Lorethova; Tomasz Wiltowski; Court Moorefield; Parag Kulkarni; Vladimir Zamansky; Ravi Kumar

    2003-12-01

    This final report summarizes the progress made on the program ''Simultaneous Production of High-Purity Hydrogen and Sequestration-Ready CO{sub 2} from Syngas (contract number DE-FG26-99FT40682)'', during October 2000 through September of 2003. GE Energy and Environmental Research (GE-EER) and Southern Illinois University (SIU) at Carbondale conducted the research work for this program. This program addresses improved methods to efficiently produce simultaneous streams of high-purity hydrogen and separated carbon dioxide from synthesis gas (syngas). The syngas may be produced through either gasification of coal or reforming of natural gas. The process of production of H{sub 2} and separated CO{sub 2} utilizes a dual-bed reactor and regenerator system. The reactor produces hydrogen and the regenerator produces separated CO{sub 2}. The dual-bed system can be operated under either a circulating fluidized-bed configuration or a cyclic fixed-bed configuration. Both configurations were evaluated in this project. The experimental effort was divided into lab-scale work at SIU and bench-scale work at GE-EER. Tests in a lab-scale fluidized bed system demonstrated the process for the conversion of syngas to high purity H{sub 2} and separated CO{sub 2}. The lab-scale system generated up to 95% H{sub 2} (on a dry basis). Extensive thermodynamic analysis of chemical reactions between the syngas and the fluidized solids determined an optimum range of temperature and pressure operation, where the extent of the undesirable reactions is minimum. The cycling of the process between hydrogen generation and oxygen regeneration has been demonstrated. The fluidized solids did not regenerate completely and the hydrogen purity in the reuse cycle dropped to 70% from 95% (on a dry basis). Changes in morphology and particle size may be the most dominant factor affecting the efficiency of the repeated cycling between hydrogen production and oxygen regeneration. The concept of

  8. The High Radiosensitizing Efficiency of a Trace of Gadolinium-Based Nanoparticles in Tumors

    Science.gov (United States)

    Dufort, Sandrine; Le Duc, Géraldine; Salomé, Murielle; Bentivegna, Valerie; Sancey, Lucie; Bräuer-Krisch, Elke; Requardt, Herwig; Lux, François; Coll, Jean-Luc; Perriat, Pascal; Roux, Stéphane; Tillement, Olivier

    2016-07-01

    We recently developed the synthesis of ultrasmall gadolinium-based nanoparticles (GBN), (hydrodynamic diameter contrast agents for magnetic resonance imaging (MRI) and as radiosensitizers. The attempt to determine the most opportune delay between the intravenous injection of GBN and the irradiation showed that a very low content of radiosensitizing nanoparticles in the tumor area is sufficient (0.1 μg/g of particles, i.e. 15 ppb of gadolinium) for an important increase of the therapeutic effect of irradiation. Such a promising and unexpected result is assigned to a suited distribution of GBN within the tumor, as revealed by the X-ray fluorescence (XRF) maps.

  9. High purity NaI(Tl) scintillator to search for dark matter

    CERN Document Server

    Fushimi, Ken-Ichi; Hazama, Ryuta; Ikeda, Haruo; Inoue, Kunio; Imagawa, Kyoshiro; Kanzaki, Gakuji; Kozlov, Alexandre; Orito, Reiko; Shima, Tatsushi; Takemoto, Yasuhiro; Teraoka, Yuri; Umehara, Saori; Yoshida, Sei

    2016-01-01

    A high purity and large volume NaI(Tl) scintillator was developed to search for cosmic dark matter. The required densities of radioactive impurities (RIs) such as U-chain, Th-chain are less than a few ppt to establish high sensitivity to dark matter. The impurity of RIs were effectively reduced by selecting raw materials of crucible and by performing chemical reduction of lead ion in NaI raw powder. The impurity of $^{226}$Ra was reduced less than 100 $\\mu$Bq/kg in NaI(Tl) crystal. It should be remarked that the impurity of $^{210}$Pb, which is difficult to reduce, is effectively reduced by chemical processing of NaI raw powder down to less than 30 $\\mu$Bq/kg. The expected sensitivity to cosmic dark matter by using 250 kg of the high purity and large volume NaI(Tl) scintillator (PICO-LON; Pure Inorganic Crystal Observatory for LOw-background Neutr(al)ino) is 7$\\times$10$^{-45}$ cm$^{2}$ for 50 GeV$/c^{2}$ WIMPs.

  10. Recycling of high purity selenium from CIGS solar cell waste materials.

    Science.gov (United States)

    Gustafsson, Anna M K; Foreman, Mark R StJ; Ekberg, Christian

    2014-10-01

    Copper indium gallium diselenide (CIGS) is a promising material in thin film solar cell production. To make CIGS solar cells more competitive, both economically and environmentally, in comparison to other energy sources, methods for recycling are needed. In addition to the generally high price of the material, significant amounts of the metals are lost in the manufacturing process. The feasibility of recycling selenium from CIGS through oxidation at elevated temperatures was therefore examined. During oxidation gaseous selenium dioxide was formed and could be separated from the other elements, which remained in solid state. Upon cooling, the selenium dioxide sublimes and can be collected as crystals. After oxidation for 1h at 800°C all of the selenium was separated from the CIGS material. Two different reduction methods for reduction of the selenium dioxide to selenium were tested. In the first reduction method an organic molecule was used as the reducing agent in a Riley reaction. In the second reduction method sulphur dioxide gas was used. Both methods resulted in high purity selenium. This proves that the studied selenium separation method could be the first step in a recycling process aimed at the complete separation and recovery of high purity elements from CIGS.

  11. Recovery of high purity sulfuric acid from the waste acid in toluene nitration process by rectification.

    Science.gov (United States)

    Song, Kai; Meng, Qingqiang; Shu, Fan; Ye, Zhengfang

    2013-01-01

    Waste sulfuric acid is a byproduct generated from numerous industrial chemical processes. It is essential to remove the impurities and recover the sulfuric acid from the waste acid. In this study the rectification method was introduced to recover high purity sulfuric acid from the waste acid generated in toluene nitration process by using rectification column. The waste acid quality before and after rectification were evaluated using UV-Vis spectroscopy, GC/MS, HPLC and other physical and chemical analysis. It was shown that five nitro aromatic compounds in the waste acid were substantially removed and high purity sulfuric acid was also recovered in the rectification process at the same time. The COD was removed by 94% and the chrominance was reduced from 1000° to 1°. The recovered sulfuric acid with the concentration reaching 98.2 wt% had a comparable quality with commercial sulfuric acid and could be recycled back into the toluene nitration process, which could avoid waste of resources and reduce the environmental impact and pollution.

  12. Derivation of high purity neuronal progenitors from human embryonic stem cells.

    Directory of Open Access Journals (Sweden)

    Gabriel Nistor

    Full Text Available The availability of human neuronal progenitors (hNPs in high purity would greatly facilitate neuronal drug discovery and developmental studies, as well as cell replacement strategies for neurodegenerative diseases and conditions, such as spinal cord injury, stroke, Parkinson's disease, Alzheimer's disease, and Huntington's disease. Here we describe for the first time a method for producing hNPs in large quantity and high purity from human embryonic stem cells (hESCs in feeder-free conditions, without the use of exogenous noggin, sonic hedgehog or analogs, rendering the process clinically compliant. The resulting population displays characteristic neuronal-specific markers. When allowed to spontaneously differentiate into neuronal subtypes in vitro, cholinergic, serotonergic, dopaminergic and/or noradrenergic, and medium spiny striatal neurons were observed. When transplanted into the injured spinal cord the hNPs survived, integrated into host tissue, and matured into a variety of neuronal subtypes. Our method of deriving neuronal progenitors from hESCs renders the process amenable to therapeutic and commercial use.

  13. Performance of bare high-purity germanium detectors in liquid argon for the GERDA experiment

    CERN Document Server

    Heider, Marik Barnabé; Chkvorets, Oleg; Di Vacri, Assunta; Gusev, Konstantin; Schönert, Stefan; Shirchenko, Mark

    2008-01-01

    The GERmanium Detector Array, GERDA, will search for neutrinoless double beta decay in 76Ge at the National Gran Sasso Laboratory of the INFN. Bare high-purity germanium detectors enriched in 76Ge will be submerged in liquid argon serving simultaneously as a shield against external radioactivity and as a cooling medium. In GERDA Phase-I, reprocessed enriched-Ge detectors, which were previously operated by the Heidelberg-Moscow and IGEX collaborations, will be redeployed. Before operating the enriched detectors, tests are performed with non-enriched bare HPGe detectors in the GERDA underground Detector Laboratory to test the Phase-I detector assembly, the detector handling protocols, the refurbishment technology and to study the long-term stability in liquid argon. The leakage currents in liquid argon and liquid nitrogen have been extensively studied under varying gamma irradiation conditions. In total three non-enriched high-purity p-type prototype germanium detectors have been operated successfully. The dete...

  14. Device to generate high purity hydroxide solution in-line for ion chromatography.

    Science.gov (United States)

    Masunaga, Hiroto; Higo, Yuji; Ishii, Mizuo; Maruyama, Noboru; Yamazaki, Shigeo

    2016-05-06

    Herein, we report a new device that generates a high-purity hydroxide solution in line. The device's container has three compartments that are isolated from each other by two cation exchange (CE) membranes. In each end of the container, an electrode is installed. The three compartments are filled with ion exchange resins. A bipolar boundary is a composite boundary comprising anion- and cation-exchangers. This device has two bipolar boundaries, which are used to separate the location of hydroxide solution generation from the location where water is electrolyzed. Therefore, it can produce high-purity hydroxide solutions that are free from gases and anionic impurities. The hydroxide solution is generated on the basis of an electrokinetic phenomenon at the surfaces of ion-exchange resins and membranes in an electric field; NaOH concentration can be controlled at rates from 0.01 to 100mM per 1mL/min by adjusting the electrical current (0-200mA) applied to the device. As the generated solution is used as an eluent for a suppressed anion chromatography, the electrical conductivity of the effluent from the suppressor is as low as that of ultra-pure water. Thus, the noise of the base-line electrical conductivity is improved, and so the detection limit of anions on the sub-ng/mL order can be achieved.

  15. Characterization of high purity lycopene from tomato wastes using a new pressurized extraction approach.

    Science.gov (United States)

    Naviglio, Daniele; Caruso, Tonino; Iannece, Patrizia; Aragòn, Alejandro; Santini, Antonello

    2008-08-13

    In this paper, a method for the extraction of high purity lycopene from tomato wastes is presented. The method is based on a pressurized extraction that uses the Extractor Naviglio, and it is performed in the 0.7-0.9 MPa range. Tomato skin, the byproduct deriving from manufacturing of tomato, in a water dispersion, are used as starting material. Lycopene is transferred, for the effect of the high pressure used, in the form of molecular aggregates into the water as a dispersion, while apolar compounds remain in the matrix. The aggregates are easily purified in a single subsequent step by using methanol, thus, obtaining lycopene at 98% chromatographic purity or higher. A new stationary phase, phenyl-hexyl silicone, and a simple water/acetonitrile gradient were used for HPLC analysis of lycopene. The extract was characterized by UV-Vis spectrophotometry, (1)H NMR, (13)C NMR, and electrospray ionization mass spectrometry. An average recovery of 2.8 mg lycopene/kg tomato waste can be obtained after 4 hours of extraction and using tap water as the extracting liquid. The recovery percentage was of about 10%. The exhausted tomato byproduct can be easily dried and used in agriculture or as feeding for animals.

  16. A solvent-extraction module for cyclotron production of high-purity technetium-99m.

    Science.gov (United States)

    Martini, Petra; Boschi, Alessandra; Cicoria, Gianfranco; Uccelli, Licia; Pasquali, Micòl; Duatti, Adriano; Pupillo, Gaia; Marengo, Mario; Loriggiola, Massimo; Esposito, Juan

    2016-12-01

    The design and fabrication of a fully-automated, remotely controlled module for the extraction and purification of technetium-99m (Tc-99m), produced by proton bombardment of enriched Mo-100 molybdenum metallic targets in a low-energy medical cyclotron, is here described. After dissolution of the irradiated solid target in hydrogen peroxide, Tc-99m was obtained under the chemical form of (99m)TcO4(-), in high radionuclidic and radiochemical purity, by solvent extraction with methyl ethyl ketone (MEK). The extraction process was accomplished inside a glass column-shaped vial especially designed to allow for an easy automation of the whole procedure. Recovery yields were always >90% of the loaded activity. The final pertechnetate saline solution Na(99m)TcO4, purified using the automated module here described, is within the Pharmacopoeia quality control parameters and is therefore a valid alternative to generator-produced (99m)Tc. The resulting automated module is cost-effective and easily replicable for in-house production of high-purity Tc-99m by cyclotrons.

  17. Efficient single photon emission from a high-purity hexagonal boron nitride crystal

    Science.gov (United States)

    Martínez, L. J.; Pelini, T.; Waselowski, V.; Maze, J. R.; Gil, B.; Cassabois, G.; Jacques, V.

    2016-09-01

    Among a variety of layered materials used as building blocks in van der Waals heterostructures, hexagonal boron nitride (hBN) appears as an ideal platform for hosting optically active defects owing to its large band gap (˜6 eV ). Here we study the optical response of a high-purity hBN crystal under green laser illumination. By means of photon correlation measurements, we identify individual defects emitting a highly photostable fluorescence under ambient conditions. A detailed analysis of the photophysical properties reveals a high quantum efficiency of the radiative transition, leading to a single photon source with very high brightness (˜4 ×106 counts s-1). These results illustrate how the wide range of applications offered by hBN could be further extended to photonic-based quantum information science and metrology.

  18. High-Purity Semiconducting Single-Walled Carbon Nanotubes: A Key Enabling Material in Emerging Electronics.

    Science.gov (United States)

    Lefebvre, Jacques; Ding, Jianfu; Li, Zhao; Finnie, Paul; Lopinski, Gregory; Malenfant, Patrick R L

    2017-09-13

    Semiconducting single-walled carbon nanotubes (sc-SWCNTs) are emerging as a promising material for high-performance, high-density devices as well as low-cost, large-area macroelectronics produced via additive manufacturing methods such as roll-to-roll printing. Proof-of-concept demonstrations have indicated the potential of sc-SWCNTs for digital electronics, radiofrequency circuits, radiation hard memory, improved sensors, and flexible, stretchable, conformable electronics. Advances toward commercial applications bring numerous opportunities in SWCNT materials development and characterization as well as fabrication processes and printing technologies. Commercialization in electronics will require large quantities of sc-SWCNTs, and the challenge for materials science is the development of scalable synthesis, purification, and enrichment methods. While a few synthesis routes have shown promising results in making near-monochiral SWCNTs, gram quantities are available only for small-diameter sc-SWCNTs, which underperform in transistors. Most synthesis routes yield mixtures of SWCNTs, typically 30% metallic and 70% semiconducting, necessitating the extraction of sc-SWCNTs from their metallic counterparts in high purity using scalable postsynthetic methods. Numerous routes to obtain high-purity sc-SWCNTs from raw soot have been developed, including density-gradient ultracentrifugation, chromatography, aqueous two-phase extraction, and selective DNA or polymer wrapping. By these methods (termed sorting or enrichment), >99% sc-SWCNT content can be achieved. Currently, all of these approaches have drawbacks and limitations with respect to electronics applications, such as excessive dilution, expensive consumables, and high ionic impurity content. Excess amount of dispersant is a common challenge that hinders direct inclusion of sc-SWCNTs into electronic devices. At present, conjugated polymer extraction may represent the most practical route to sc-SWCNTs. By the use of

  19. Direct Determination of Trace Impurities in High Purity Zinc Oxide by High Resolution Inductively Coupled Plasma Mass Spectrometry

    Institute of Scientific and Technical Information of China (English)

    XIE Hualin; NIE Xidu; LI Libo; SONG Chuhua

    2006-01-01

    The determination of trace impurities in high purity zinc oxide by high resolution inductively coupled plasma mass spectrometry (HR-ICP-MS) was investigated. To overcome some potentially problematic spectral interference, measurements were acquired in both middle and high resolution modes. The matrix effects due to the presence of excess HCl and zinc were evaluated. The optimum conditions for the determination were tested and discussed. The standard addition method was employed for quantitative analysis. The detection limits ranged from 0.02 μg/g to 6 μg/g depending on the elements.The experimental results for the determination of Na, Mg, Ca, Cr, Mn, Fe, Co, Ni, Cu, Mo, Cd, Sb and Pb in several high purity zinc oxide powders were presented.

  20. Renewable rigid diamines: efficient, stereospecific synthesis of high purity isohexide diamines.

    Science.gov (United States)

    Thiyagarajan, Shanmugam; Gootjes, Linda; Vogelzang, Willem; van Haveren, Jacco; Lutz, Martin; van Es, Daan S

    2011-12-16

    We report an efficient three-step strategy for synthesizing rigid, chiral isohexide diamines derived from 1,4:3,6-dianhydrohexitols. These biobased chiral building blocks are presently the subject of several investigations (in our and several other groups) because of their application in high-performance biobased polymers, such as polyamides and polyurethanes. Among the three possible stereo-isomers, dideoxy-diamino isoidide and dideoxy-diamino isosorbide can be synthesized from isomannide and isosorbide respectively in high yield with absolute stereo control. Furthermore, by using this methodology dideoxy-amino isomannide-a tricyclic adduct-was obtained starting from isoidide in high yield. Our improved synthetic route is a valuable advance towards meeting scale and purity demands for evaluating the properties of new biobased performance materials, which will benefit the development of these plastics.

  1. Strength and structural phase transitions of gadolinium at high pressure from radial X-ray diffraction

    Energy Technology Data Exchange (ETDEWEB)

    Xiong, Lun, E-mail: xionglun@ihep.ac.cn; Liu, Jing; Bai, Ligang; Li, Xiaodong; Lin, Chuanlong [Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049 (China); Lin, Jung-Fu [Department of Geological Sciences, Jackson School of Geosciences, The University of Texas at Austin, Texas 78712 (United States)

    2014-12-28

    Lattice strength and structural phase transitions of gadolinium (Gd) were determined under nonhydrostatic compression up to 55 GPa using an angle-dispersive radial x-ray diffraction technique in a diamond-anvil cell at room temperature. Three new phases of fcc structure, dfcc structure, and new monoclinic structure were observed at 25 GPa, 34 GPa, and 53 GPa, respectively. The radial x-ray diffraction data yield a bulk modulus K{sub 0} = 36(1) GPa with its pressure derivate K{sub 0}′ = 3.8(1) at the azimuthal angle between the diamond cell loading axis and the diffraction plane normal and diffraction plane ψ = 54.7°. With K{sub 0}′ fixed at 4, the derived K{sub 0} is 34(1) GPa. In addition, analysis of diffraction data with lattice strain theory indicates that the ratio of differential stress to shear modulus (t/G) ranges from 0.011 to 0.014 at pressures of 12–55 GPa. Together with estimated high-pressure shear moduli, our results show that Gd can support a maximum differential stress of 0.41 GPa, while it starts to yield to plastic deformation at 16 GPa under uniaxial compression. The yield strength of Gd remains approximately a constant with increasing pressure, and reaches 0.46 GPa at 55 GPa.

  2. Effect of microplastic deformation on the electron ultrasonic absorption in high-purity molybdenum monocrystals

    Energy Technology Data Exchange (ETDEWEB)

    Pal' -Val' , P.P.; Kaufmann, Kh.J.

    1983-03-01

    The low temperature (100-6 K) linear absorption of ultrasound (88 kHz) by high purity molybdenum single crystals have been studied. Both unstrained samples and samples sub ected to microplastic deformation (epsilon<=0.45%) were used. Unstrained samples displayed at T<30 K a rapid increase in the absorption with lowering temperature which is interpreted as an indication of electron viscosity due to electron-phonon collisions. After deformation this part of absorption disappeared. This seems to suggest that microplastic deformation brings about in the crystal a sufficiently large number of defects that can compete with phonons in restricting the electron mean free path. A low temperature dynamic annealing has been revealed in strained samples, that is almost complete recovery of the absorption nature under irradiation with high amplitude sound, epsilon/sub 0/ approximately 10/sup -4/, during 10 min, at 6 K. A new relaxation peak of absorption at 10 K has been found in strained samples.

  3. Hot working of high purity Fe-C alloys in the {alpha}-range

    Energy Technology Data Exchange (ETDEWEB)

    Montheillet, F; Le Coze, J, E-mail: montheil@emse.f [Ecole des Mines (SMS), CNRS UMR 5146, 158 cours Fauriel, 42023 Saint-Etienne Cedex 2 (France)

    2010-07-01

    The influence of carbon in solid solution on the stress-strain curves of {alpha}-iron was investigated using model alloys prepared from high purity iron. Uniaxial compression tests were carried out within the ferritic domain at temperatures between 700 and 880 {sup 0}C. Oscillating stress-strain curves observed at high temperatures and low strain rates indicate that discontinuous dynamic recrystallization takes place. The macroscopic strain rate sensitivities m and apparent activation energies Q associated with the flow stress are not significantly modified by carbon additions. By contrast, the 'mesoscopic' parameters h and r associated with strain hardening and dynamic recovery, respectively, are strongly dependent on the carbon content. Finally, an estimation of the grain boundary mobilities during dynamic recrystallization was carried out from the above rheological data.

  4. Annealing Behavior at Triple Junctions in High-Purity Aluminum After Slight Cold Rolling

    Science.gov (United States)

    Yin, Wenhong; Wang, Weiguo; Fang, Xiaoying; Qin, Congxiang

    2017-04-01

    High-purity polycrystalline aluminum samples with a typical grain size of approximately 30 μm were slightly cold-rolled with a thickness reduction of 15%, and then, off-line in situ electron backscatter diffraction was used to identify the annealing behavior at triple junctions during annealing at 400 °C. The results show that recrystallization nuclei are developed at some triple junctions during annealing. High-angle grain boundaries migrate from harder grains to softer grains at the triple junctions leading to the formation of nuclei. All such nuclei show Σ3 orientation relationships with the parent grains, and the bounded Σ3 boundaries are found to be incoherent. During further annealing, these nuclei are consumed by other growing grains, indicating that their presence is just a release of the strain concentration at the triple junctions.

  5. Annealing Behavior at Triple Junctions in High-Purity Aluminum After Slight Cold Rolling

    Science.gov (United States)

    Yin, Wenhong; Wang, Weiguo; Fang, Xiaoying; Qin, Congxiang

    2017-02-01

    High-purity polycrystalline aluminum samples with a typical grain size of approximately 30 μm were slightly cold-rolled with a thickness reduction of 15%, and then, off-line in situ electron backscatter diffraction was used to identify the annealing behavior at triple junctions during annealing at 400 °C. The results show that recrystallization nuclei are developed at some triple junctions during annealing. High-angle grain boundaries migrate from harder grains to softer grains at the triple junctions leading to the formation of nuclei. All such nuclei show Σ3 orientation relationships with the parent grains, and the bounded Σ3 boundaries are found to be incoherent. During further annealing, these nuclei are consumed by other growing grains, indicating that their presence is just a release of the strain concentration at the triple junctions.

  6. Status of Research on Application of High Purity Rare Earth Oxides in Solid Oxide Fuel Cells

    Institute of Scientific and Technical Information of China (English)

    Ma Zhihong; Qiu Jufeng

    2004-01-01

    The solid oxide fuel cell (SOFC) is a high-efficient and environmentally friendly power generation system.The rare earth oxide materials are used extensively in the manufacturing of SOFC components.In particular, the CeO2doped with Gd2O3 or Sm2O3, lanthanide perovskite oxides are indispensable and key materials for developing the intermediate temperature SOFC.The research and development status of application of high purity rare earth oxides in SOFC was overviewed.The rare earth oxide-based and -doped materials were discussed for the SOFC components.Concerning the rare earth oxides applicable to SOFC, several topics were also pointed out for further researching and developing.

  7. Preparative separation of high-purity cordycepin from Cordyceps militaris(L.) Link by high-speed countercurrent chromatography

    Science.gov (United States)

    Zhu, Licai; Liang, Yong; Lao, Deqiang; Zhang, Tianyou; Ito, Yoichiro

    2009-01-01

    A high-speed counter-current chromatography (HSCCC) technique in a preparative scale has been applied to separate and purify cordycepin from the extract of Cordyceps militaris(L.) Link by a one-step separation. A high efficiency of HSCCC separation was achieved on a two-phase solvent system of n-hexane–n-butanol–methanol–water (23:80:30:155, v/v/v/v) by eluting the lower mobile phase at a flow rate of 2 ml/min under a revolution speed of 850 rpm. HSCCC separation of 216.2 mg crude sample (contained cordycepin at 44.7% purity after 732 cation-exchange resin clean-up) yielded 64.8 mg cordycepin with purity of 98.9% and 91.7% recovery. Identification of the target compound was performed by UV, IR, MS, 1H NMR and 13C NMR. PMID:21643461

  8. High purity polyimide analysis by solid sampling graphite furnace atomic absorption spectrometry

    Science.gov (United States)

    Santos, Rafael F.; Carvalho, Gabriel S.; Duarte, Fabio A.; Bolzan, Rodrigo C.; Flores, Erico M. M.

    2017-03-01

    In this work, Cr, Cu, Mn, Na and Ni were determined in high purity polyimides (99.5%) by solid sampling graphite furnace atomic absorption spectrometry (SS-GFAAS) using Zeeman effect background correction system with variable magnetic field, making possible the simultaneous measurement at high or low sensitivity. The following analytical parameters were evaluated: pyrolysis and atomization temperatures, feasibility of calibration with aqueous solution, linear calibration range, sample mass range and the use of chemical modifier. Calibration with aqueous standard solutions was feasible for all analytes. No under or overestimated results were observed and up to 10 mg sample could be introduced on the platform for the determination of Cr, Cu, Mn, Na and Ni. The relative standard deviation ranged from 3 to 20%. The limits of detection (LODs) achieved using the high sensitivity mode were as low as 7.0, 2.5, 1.7, 17 and 0.12 ng g- 1 for Cr, Cu, Mn, Na and Ni, respectively. No addition of chemical modifier was necessary, except for Mn determination where Pd was required. The accuracy was evaluated by analyte spike and by comparison of the results with those obtained by inductively coupled plasma optical emission spectrometry and inductively coupled plasma mass spectrometry after microwave-assisted digestion in a single reaction chamber system and also by neutron activation analysis. No difference among the results obtained by SS-GFAAS and those obtained by alternative analytical methods using independent techniques. SS-GFAAS method showed some advantages, such as the determination of metallic contaminants in high purity polyimides with practically no sample preparation, very low LODs, calibration with aqueous standards and determination in a wide range of concentration.

  9. Gadolinium-doped water cerenkov-based neutron and high energy gamma-ray detector and radiation portal monitoring system

    Science.gov (United States)

    Dazeley, Steven A; Svoboda, Robert C; Bernstein, Adam; Bowden, Nathaniel

    2013-02-12

    A water Cerenkov-based neutron and high energy gamma ray detector and radiation portal monitoring system using water doped with a Gadolinium (Gd)-based compound as the Cerenkov radiator. An optically opaque enclosure is provided surrounding a detection chamber filled with the Cerenkov radiator, and photomultipliers are optically connected to the detect Cerenkov radiation generated by the Cerenkov radiator from incident high energy gamma rays or gamma rays induced by neutron capture on the Gd of incident neutrons from a fission source. The PMT signals are then used to determine time correlations indicative of neutron multiplicity events characteristic of a fission source.

  10. Application of Thermodynamic Calculations to the Pyro-refining Process for Production of High Purity Bismuth

    Science.gov (United States)

    Mezbahul-Islam, Mohammad; Belanger, Frederic; Chartrand, Patrice; Jung, In-Ho; Coursol, Pascal

    2017-02-01

    The present work has been performed with the aim to optimize the existing process for the production of high purity bismuth (99.999 pct). A thermo-chemical database including most of the probable impurities of bismuth (Bi-X, X = Ag, Au, Al, Ca, Cu, Fe, Mg, Mn, Na, Ni, Pb, S, Sb, Sn, Si, Te, Zn) has been constructed to perform different thermodynamic calculations required for the refining process. Thermodynamic description for eight of the selected binaries, Bi-Ca, Cu, Mn, Ni, Pb, S, Sb, and Sn, has been given in the current paper. Using the current database, different thermodynamic calculations have been performed to explain the steps involved in the bismuth refining process.

  11. High Purity Tungsten Spherical Particle Preparation From WC-Co Spent Hard Scrap

    Directory of Open Access Journals (Sweden)

    Han Chulwoong

    2015-06-01

    Full Text Available Tungsten carbide-cobalt hard metal scrap was recycled to obtain high purity spherical tungsten powder by a combined hydrometallurgy and physical metallurgy pathway. Selective leaching of tungsten element from hard metal scrap occurs at solid / liquid interface and therefore enlargement of effective surface area is advantageous. Linear oxidation behavior of Tungsten carbide-cobalt and the oxidized scrap is friable to be pulverized by milling process. In this regard, isothermally oxidized Tungsten carbide-cobalt hard metal scrap was mechanically broken into particles and then tungsten trioxide particle was recovered by hydrometallurgical method. Recovered tungsten trioxide was reduced to tungsten particle in a hydrogen environment. After that, tungsten particle was melted and solidified to make a spherical one by RF (Ratio Frequency thermal plasma process. Well spherical tungsten micro-particle was successfully obtained from spent scrap. In addition to the morphological change, thermal plasma process showed an advantage for the purification of feedstock particle.

  12. Defects interaction processes in deformed high purity polycrystalline molybdenum at elevated temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Lambri, O.A., E-mail: olambri@fceia.unr.edu.ar [Laboratorio de Materiales, Escuela de Ingeniería Eléctrica, Centro de Tecnología e Investigación Eléctrica, Facultad de Ciencias Exactas, Ingeniería y Agrimensura, Universidad Nacional de Rosario – CONICET, Avda. Pellegrini 250, (2000) Rosario (Argentina); Bonifacich, F.G. [Laboratorio de Materiales, Escuela de Ingeniería Eléctrica, Centro de Tecnología e Investigación Eléctrica, Facultad de Ciencias Exactas, Ingeniería y Agrimensura, Universidad Nacional de Rosario – CONICET, Avda. Pellegrini 250, (2000) Rosario (Argentina); Bozzano, P.B. [Laboratorio de Microscopía Electrónica, Unidad de Actividad Materiales, Centro Atómico Constituyentes, Comisión Nacional de Energía Atómica e Instituto Sábato – Universidad Nacional de San Martín, Avda. Gral. Paz 1499, (1650) San Martín (Argentina); Zelada, G.I. [Laboratorio de Materiales, Escuela de Ingeniería Eléctrica, Centro de Tecnología e Investigación Eléctrica, Facultad de Ciencias Exactas, Ingeniería y Agrimensura, Universidad Nacional de Rosario – CONICET, Avda. Pellegrini 250, (2000) Rosario (Argentina); and others

    2014-10-15

    Mechanical spectroscopy (damping and elastic modulus as a function of temperature) and transmission electron microscopy studies have been performed in high purity polycrystalline molybdenum plastically deformed to different values of tensile and torsion strain. Mechanical spectroscopy measurements were performed from room temperature up to 1285 K. A relaxation peak in polycrystalline molybdenum related to the movement of dislocations into lower energy configurations near grain boundaries has been discovered to appear around 1170 K. The activation energy of the peak is 4.2 eV ± 0.5 eV. This relaxation phenomenon involves the interaction between vacancies and mobile dislocations near the grain boundaries. It should be highlighted that this relaxation process is controlled by the arrangement of vacancies and dislocations which occur at temperature below 1070 K.

  13. Synthesis of Magnetite Nanoparticles by Top-Down Approach from a High Purity Ore

    Directory of Open Access Journals (Sweden)

    Gayan Priyadarshana

    2015-01-01

    Full Text Available This study attempts to synthesize magnetite nanoparticles from a high purity natural iron oxide ore found in Panvila, Sri Lanka, following a novel top-down approach. Powder X-Ray diffraction, elemental analysis, and chemical analysis data confirmed the ore to be exclusively magnetite with Fe2+ : Fe3+ ratio of 1 : 2. Surface modified magnetite nanoparticles were synthesized by destructuring of this ore using a top-down approach in the presence of oleic acid. These oleic acid coated nanoparticles were further dispersed in ethanol resulting in stable nanomagnetite dispersion. Interestingly, the nanoparticles demonstrated a spherical morphology with a particle size ranging from 20 to 50 nm. Magnetic force microscopic data was used to confirm the topography of the nanoparticles and to study the magnetic domain structure.

  14. A simple high-sensitivity technique for purity analysis of xenon gas

    CERN Document Server

    Leonard, D S; Hall, C; Kaufman, L; Langford, T; Slutsky, S; Yen, Y R

    2010-01-01

    We report on the development and performance of a high-sensitivity purity-analysis technique for gaseous xenon. The gas is sampled at macroscopic pressure from the system of interest using a UHV leak valve. The xenon present in the sample is removed with a liquid-nitrogen cold trap, and the remaining impurities are observed with a standard vacuum mass-spectroscopy device. Using calibrated samples of xenon gas spiked with known levels of impurities, we find that the minimum detectable levels of N2, O2, and methane are 1 ppb, 160 ppt, and 60 ppt respectively. This represents an improvement of about a factor of 10,000 compared to measurements performed without a coldtrap.

  15. Role of deformation twins in static recrystallization kinetics of high-purity alpha titanium

    Science.gov (United States)

    Won, Jong Woo; Lee, Taekyung; Hong, Seong-Gu; Lee, Yongmoon; Lee, Jeong Hun; Lee, Chong Soo

    2016-11-01

    The importance of deformation twins in static recrystallization kinetics of high-purity alpha titanium was investigated by carrying out thermal annealing tests of deformed materials in combination with electron-backscatterdiffraction- based microstructural analysis. Prior to thermal annealing, the material was compressed to a true strain of 0.22 along three directions to introduce different twinning characteristics. Our results showed that deformation twins substantially promoted the static recrystallization process by deepening the microstructural inhomogeneity induced by the formation of twin boundaries and twinning-induced crystallographic lattice reorientation. Twin morphology was also observed to be important because it influenced the extent of microstructural inhomogeneity. Intersecting twin morphology, caused by the activation of multiple twin variants, was more effective than parallel twin morphology, caused by the activation of a single twin variant (or a twin variant pair), because it gave rise to more twin boundaries, more twin boundary junctions (intersections, triple junctions, etc.), and greater in-grain crystallographic orientation spread.

  16. A Rapid and Cost-Effective Laser Based Synthesis of High Purity Cadmium Selenide Quantum Dots.

    Science.gov (United States)

    Gondall, M A; Qahtan, Talal F; Dastageer, M A; Yamani, Z H; Anjum, D H

    2016-01-01

    A rapid and cost effective method is developed to synthesize high purity cadmium Selenide (CdSe) quantum dots in acetone medium using second harmonic of Nd:YAG nanosecond pulsed laser of 532 nm wavelength. The thermal agglomeration due the nanosecond pulse duration of the laser was successfully eliminated by using unfocussed laser beam and thereby providing a favorable conditions for the synthesis of quantum dots having the grain size of 3 nm. The morphological and optical characterizations like XRD, HRTEM, optical absorption of the synthesized CdSe quantum dots, reveal that the material possesses the similar characteristics of the one synthesized through cumbersome wet chemical methods. Relative to the CdSe bulk material, the synthesized CdSe quantum dots showed a blue shift in the measured band gap energy from near infrared spectral region to visible region, making this material very attractive for many solar energy harvesting applications like photo-catalysis and solar cells.

  17. All-fibre multiplexed source of high-purity heralded single photons

    CERN Document Server

    Francis-Jones, Robert J A; Mosley, Peter J

    2016-01-01

    Single photon sources based on spontaneous photon-pair generation have enabled pioneering experiments in quantum optics. However, their non-determinism presents a bottleneck to scaling up photonic and hybrid quantum-enhanced technologies. Furthermore, photon pairs are typically emitted into many correlated frequency modes, producing an undesirable mixed state on heralding. Here we present a complete fibre-integrated heralded single photon source that addresses both these difficulties simultaneously. We use active switching to provide a path to deterministic operation by multiplexing separate spontaneous sources, and dispersion engineering to minimise frequency correlation for high-purity single photon generation. All the essential elements -- nonlinear material with dispersion control, wavelength isolation, optical delay, and fast switching -- are incorporated in a low-loss alignment-free package that heralds photons in telecoms single-mode fibre. Our results demonstrate a scalable approach to delivering pure...

  18. High purity 100 GeV electron identification with synchrotron radiation arXiv

    CERN Document Server

    Depero, E.; Burtsev, V.; Chumakov, A.; Cooke, D.; Dermenev, A.V.; Donskov, S.V.; Dubinin, F.; Dusaev, R.R.; Emmenegger, S.; Fabich, A.; Frolov, V.N.; Gardikiotis, A.; Gninenko, S.N.; Hösgen, M.; Karneyeu, A.E.; Ketzer, B.; Kirsanov, M.M.; Konorov, I.V.; Kramarenko, V.A.; Kuleshov, S.V.; Lyubovitskij, V.E.; Lysan, V.; Matveev, V.A.; Mikhailov, Yu.V.; Myalkovskiy, V.V.; Peshekhonov, V.D.; Peshekhonov, D.V.; Polyakov, V.A.; Radics, B.; Rubbia, A.; Samoylenko, V.D.; Tikhomirov, V.O.; Tlisov, D.A.; Toropin, A.N.; Vasilishin, B.; Vasquez Arenas, G.; Ulloa, P.; Crivelli, P.

    In high energy experiments such as active beam dump searches for rare decays and missing energy events, the beam purity is a crucial parameter. In this paper we present a technique to reject heavy charged particle contamination in the 100 GeV electron beam of the H4 beam line at CERN SPS. The method is based on the detection with BGO scintillators of the synchrotron radiation emitted by the electrons passing through a bending dipole magnet. A 100 GeV $\\pi^-$ beam is used to test the method in the NA64 experiment resulting in a suppression factor of $10^{-5}$ while the efficiency for electron detection is $\\sim$95%. The spectra and the rejection factors are in very good agreement with the Monte Carlo simulation. The reported suppression factors are significantly better than previously achieved.

  19. Method of Preparation for High-Purity Nanocrystalline Anhydrous Cesium Perrhenate

    Directory of Open Access Journals (Sweden)

    Katarzyna Leszczyńska-Sejda

    2017-03-01

    Full Text Available This paper is devoted to the preparation of high-purity anhydrous nanocrystalline cesium perrhenate, which is applied in catalyst preparation. It was found that anhydrous cesium perrhenate with a crystal size <45 nm can be obtained using cesium ion sorption and elution using aqueous solutions of perrhenic acid with subsequent crystallisation, purification, and drying. The following composition of the as-obtained product was reported: 34.7% Cs; 48.6% Re and <2 ppm Bi; <3 ppm Zn; <2 ppm As; <10 ppm Ni; < 3 ppm Mg; <5 ppm Cu; <5 ppm Mo; <5 ppm Pb; <10 ppm K; <2 ppm Na; <5 ppm Ca; <3 ppm Fe.

  20. Crystallographic Analysis of Nucleation at Hardness Indentations in High-Purity Aluminum

    Science.gov (United States)

    Xu, Chaoling; Zhang, Yubin; Lin, Fengxiang; Wu, Guilin; Liu, Qing; Juul Jensen, Dorte

    2016-12-01

    Nucleation at Vickers hardness indentations has been studied in high-purity aluminum cold-rolled 12 pct. Electron channeling contrast was used to measure the size of the indentations and to detect nuclei, while electron backscattering diffraction was used to determine crystallographic orientations. It is found that indentations are preferential nucleation sites. The crystallographic orientations of the deformed grains affect the hardness and the nucleation potentials at the indentations. Higher hardness gives increased nucleation probabilities. Orientation relationships between nuclei developed at different indentations within one original grain are analyzed and it is found that the orientation distribution of the nuclei is far from random. It is suggested that it relates to the orientations present near the indentation tips which in turn depend on the orientation of the selected grain in which they form. Finally, possible nucleation mechanisms are briefly discussed.

  1. High purity 100 GeV electron identification with synchrotron radiation

    Science.gov (United States)

    Depero, E.; Banerjee, D.; Burtsev, V.; Chumakov, A.; Cooke, D.; Dermenev, A. V.; Donskov, S. V.; Dubinin, F.; Dusaev, R. R.; Emmenegger, S.; Fabich, A.; Frolov, V. N.; Gardikiotis, A.; Gninenko, S. N.; Hösgen, M.; Karneyeu, A. E.; Ketzer, B.; Kirsanov, M. M.; Konorov, I. V.; Kramarenko, V. A.; Kuleshov, S. V.; Lyubovitskij, V. E.; Lysan, V.; Matveev, V. A.; Mikhailov, Yu. V.; Myalkovskiy, V. V.; Peshekhonov, V. D.; Peshekhonov, D. V.; Polyakov, V. A.; Radics, B.; Rubbia, A.; Samoylenko, V. D.; Tikhomirov, V. O.; Tlisov, D. A.; Toropin, A. N.; Vasilishin, B.; Arenas, G. Vasquez; Ulloa, P.; Crivelli, P.

    2017-09-01

    In high energy experiments such as active beam dump searches for rare decays and missing energy events, the beam purity is a crucial parameter. In this paper we present a technique to reject heavy charged particle contamination in the 100 GeV electron beam of the H4 beam line at CERN SPS. The method is based on the detection with BGO scintillators of the synchrotron radiation emitted by the electrons passing through a bending dipole magnet. A 100 GeV π- beam is used to test the method in the NA64 experiment resulting in a suppression factor of 10-5 while the efficiency for electron detection is ∼95%. The spectra and the rejection factors are in very good agreement with the Monte Carlo simulation. The reported suppression factors are significantly better than previously achieved.

  2. High performance magneto-fluorescent nanoparticles assembled from terbium and gadolinium 1,3-diketones

    OpenAIRE

    Zairov, Rustem; Mustafina, Asiya; Shamsutdinova, Nataliya; Nizameev, Irek; Moreira, Beatriz; Sudakova, Svetlana; Podyachev, Sergey; Fattakhova, Alfia; Safina, Gulnara; Lundstrom, Ingemar; Gubaidullin, Aidar; Vomiero, Alberto

    2017-01-01

    Polyelectrolyte-coated nanoparticles consisting of terbium and gadolinium complexes with calix[4]arene tetra-diketone ligand were first synthesized. The antenna effect of the ligand on Tb(III) green luminescence and the presence of water molecules in the coordination sphere of Gd(III) bring strong luminescent and magnetic performance to the core-shell nanoparticles. The size and the core-shell morphology of the colloids were studied using transmission electron microscopy and dynamic light sca...

  3. High-purity 3D nano-objects grown by focused-electron-beam induced deposition

    Science.gov (United States)

    Córdoba, Rosa; Sharma, Nidhi; Kölling, Sebastian; Koenraad, Paul M.; Koopmans, Bert

    2016-09-01

    To increase the efficiency of current electronics, a specific challenge for the next generation of memory, sensing and logic devices is to find suitable strategies to move from two- to three-dimensional (3D) architectures. However, the creation of real 3D nano-objects is not trivial. Emerging non-conventional nanofabrication tools are required for this purpose. One attractive method is focused-electron-beam induced deposition (FEBID), a direct-write process of 3D nano-objects. Here, we grow 3D iron and cobalt nanopillars by FEBID using diiron nonacarbonyl Fe2(CO)9, and dicobalt octacarbonyl Co2(CO)8, respectively, as starting materials. In addition, we systematically study the composition of these nanopillars at the sub-nanometer scale by atom probe tomography, explicitly mapping the homogeneity of the radial and longitudinal composition distributions. We show a way of fabricating high-purity 3D vertical nanostructures of ˜50 nm in diameter and a few micrometers in length. Our results suggest that the purity of such 3D nanoelements (above 90 at% Fe and above 95 at% Co) is directly linked to their growth regime, in which the selected deposition conditions are crucial for the final quality of the nanostructure. Moreover, we demonstrate that FEBID and the proposed characterization technique not only allow for growth and chemical analysis of single-element structures, but also offers a new way to directly study 3D core-shell architectures. This straightforward concept could establish a promising route to the design of 3D elements for future nano-electronic devices.

  4. Assessment of radiochemical purity of [{sup 18}F]fludeoxyglucose by high pressure liquid chromatography (HPLC)

    Energy Technology Data Exchange (ETDEWEB)

    Lacerda, Aline E.; Silva, Juliana B.; Silveira, Marina B.; Ferreira, Soraya Z., E-mail: radiofarmacoscdtn@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil). Unidade de Pesquisa e Producao de Radiofarmacos

    2011-07-01

    The quality control of [{sup 18}F]fludeoxyglucose ({sup 18}FDG) has received attention due to its increasing clinical use. Although the quality requirements of {sup 18}FDG are established in various pharmacopoeia, the suitability of all testing methods used should be verified under actual conditions of use and documented. The aim of this study was to develop a high pressure liquid chromatography (HPLC) method for radiochemical purity evaluation of {sup 18}FDG, based on pharmacopoeia references, and to verify its suitability for routine quality control in our centre. HPLC analysis was performed with an Agilent HPLC. {sup 18}FDG and impurities were separated on an anion-exchange column by isocratic elution with 0.1 M NaOH as the mobile phase. Detection was accomplished with refractive index and NaI (Tl) scintillation detectors. The flow rate of the mobile phase was set at 0.8 mL/min and the column temperature was kept at 35 deg C. Specificity, linearity, precision and robustness were assessed to verify if the method was adequate for its intended purpose. Retention time of {sup 18}FDG was not affected by the presence of other components of the formulation and a good peak resolution was achieved. The analytical curve of {sup 18}FDG was linear, with a correlation coefficient value of 0.9995. Intraday repeatable precision, reported as the relative standard deviation, was 0.11%. Analytical procedure remained unaffected by small variations in mobile phase flow rate. Results evidenced that HPLC is suitable for radiochemical purity evaluation of {sup 18}FDG, considering operational conditions of our laboratory. (author)

  5. Investigation of applicability of high purity tetraaminenickel(II perrhenate to Re-Ni alloy powder production

    Directory of Open Access Journals (Sweden)

    Tomasz Majewski

    2016-07-01

    Full Text Available In this paper, a method for preparation of high purity tetraaminenickel(II perrhenate is presented. This method comprises reacting of a concentrated solution of ammonia water with high purity anhydrous nickel(II perrhenate(VII. The resulting tetraaminenickel(II perrhenate is reduced under dissociated ammonia conditions, to obtain Re-Ni alloy powder. The article also provides information on selected physicochemical properties of the produced powder. Such Re-Ni alloy powder can be applied for tungsten heavy alloys production. Keywords: tetraaminenickel(II perrhenate, reduction, heavy alloys, rhenium

  6. Characterization of high-purity niobium structures fabricated using the electron beam melting process

    Science.gov (United States)

    Terrazas Najera, Cesar Adrian

    Additive Manufacturing (AM) refers to the varied set of technologies utilized for the fabrication of complex 3D components from digital data in a layer-by-layer fashion. The use of these technologies promises to revolutionize the manufacturing industry. The electron beam melting (EBM) process has been utilized for the fabrication of fully dense near-net-shape components from various metallic materials. This process, catalogued as a powder bed fusion technology, consists of the deposition of thin layers (50 - 120microm) of metallic powder particles which are fused by the use of a high energy electron beam and has been commercialized by Swedish company Arcam AB. Superconducting radio frequency (SRF) cavities are key components that are used in linear accelerators and other light sources for studies of elemental physics. Currently, cavity fabrication is done by employing different forming processes including deep-drawing and spinning. In both of the latter techniques, a feedstock high-purity niobium sheet with a thickness ranging from 3-4 mm is mechanically deformed and shaped into the desired geometry. In this manner, half cavities are formed that are later joined by electron beam welding (EBW). The welding step causes variability in the shape of the cavity and can also introduce impurities at the surface of the weld interface. The processing route and the purity of niobium are also of utmost importance since the presence of impurities such as inclusions or defects can be detrimental for the SRF properties of cavities. The focus of this research was the use of the EBM process in the manufacture of high purity niobium parts with potential SRF applications. Reactor grade niobium was plasma atomized and used as the precursor material for fabrication using EBM. An Arcam A2 system was utilized for the fabrication. The system had all internal components of the fabrication chamber replaced and was cleaned to prevent contamination of niobium powder. A mini-vat, developed at

  7. High-purity hydrogen generation by ultraviolet illumination with the membrane composed of titanium dioxide nanotube array and Pd layer

    Science.gov (United States)

    Hattori, Masashi; Noda, Kei; Matsushige, Kazumi

    2011-09-01

    High-purity hydrogen generation was observed by using a membrane composed of a bilayer of an anodized titanium dioxide nanotube array (TNA) and a hydrogen permeable metal. This membrane was fabricated by transferring a TNA embedded in a titanium foil onto a sputtered 10-μm-thick palladium film. Alcohols are reformed photocatalytically and concurrently generated hydrogen is purified through the Pd layer. H2 with a purity of more than 99% was obtained from liquid alcohols under ultraviolet illumination onto the membrane. Thus, we demonstrated the integration of photocatalytic hydrogen production and purification within a single membrane.

  8. Isolated High-Purity Platinum Nanowire Growth via Field Emission from a Multi-Walled Carbon Nanotube

    Science.gov (United States)

    Yang, Zhan; Nakajima, Masahiro; Saito, Yahachi; Ode, Yasuhito; Fukuda, Toshio

    2011-03-01

    Isolated high-purity platinum nanowire growth was presented via field emission from the tip of a multi-walled carbon nanotube (MWCNT) with a precursor of cyclopentadienyl-trimethyl-platinum(IV) (CpPtMe3) inside a scanning electron microscope (SEM). A nanomanipulation system was used to adjust the gap between the anode (tungsten probe) and cathode (MWCNT) in order to control the nanowire growth length which achieved a platinum nanowire length of 1.18 µm. The chemical composition of the platinum nanowire analyzed by energy-dispersive X-ray spectroscopy (EDS) shows that the purity of the platinum in the nanowire reaches 94.9 wt %.

  9. Effect of microplastic deformation on the electron ultrasonic absorption in high-purity molybdenum monocrystals

    Energy Technology Data Exchange (ETDEWEB)

    Pal' -Val' , P.P. (AN Ukrainskoj SSR, Kharkov. Fiziko-Tekhnicheskij Inst. Nizkikh Temperatur); Kaufmann, Kh.J. (Akademie der Wissenschaften der DDR, Berlin)

    1983-03-01

    The low temperature (100-6 K) linear absorption of ultrasound (88 kHz) by high purity molybdenum single crystals have been studied. Both unstrained samples and samples subjected to microplastic deformation (epsilon<=0.45%) were used. Unstrained samples displayed at T<30 K a rapid increase in the absorption with lowering temperature which is interpreted as an indication of electron viscosity due to electron-phonon collisions. After deformation this part of absorption disappeared. This seems to suggest that microplastic deformation brings about in the crystal a sufficiently large number of defects that can compete with phonons in restricting the electron mean free path. A low temperature ''dynamic annealing'' has been revealed in strained samples, that is, almost complete recovery of the absorption nature under irradiation with high amplitude sound, epsilon/sub 0/ approximately 10/sup -4/, during 10 min, at 6 K. A new relaxation peak of absorption at 10 K has been found in strained samples.

  10. Simultaneously Recovering High-Purity Chromium and Removing Organic Pollutants from Tannery Effluent

    Directory of Open Access Journals (Sweden)

    Jie Zong

    2016-01-01

    Full Text Available Chromium pollution is a serious issue because of carcinogenic toxicities of the pollutants and low recovery rate of chromium because of the presence of organic, such as protein and fat. In this work, high recovery rate and high purity of the chromium ion were successfully prepared by the way of acid enzyme, flocculant, and Fenton oxidation. The experiments were characterized by TG, TOC, UV-VIS, and SEM. In the work, the tannery waste chrome liquor was used as experimental material. The results showed that the percentage of reduction of TOC in the tannery waste chrome liquor by method of Fenton oxidation, acid enzyme, and the flocculant was 71.15%, 65.26%, and 22.05%, respectively. Therefore, the organism content of chrome tanning waste liquid was greatly reduced through the pretreatment. And the application experiment showed that the properties and grain surface and fibers of the tanned leather with commercial chromium powder and chrome tanning agent prepared from the chromium waste liquid treated with Fenton are nearly the same.

  11. Determination of halogens and sulfur in high-purity polyimide by IC after digestion by MIC.

    Science.gov (United States)

    Krzyzaniak, Sindy R; Santos, Rafael F; Dalla Nora, Flavia M; Cruz, Sandra M; Flores, Erico M M; Mello, Paola A

    2016-09-01

    In this work, a method for sample preparation of high-purity polyimide was proposed for halogens and sulfur determination by ion chromatography (IC) with conductivity detection and, alternatively, by inductively coupled plasma mass spectrometry (ICP-MS). A relatively high polyimide mass (600mg) was completely digested by microwave-induced combustion (MIC) using 20bar of O2 and 50mmolL(-1) NH4OH as absorbing solution. These conditions allowed final solutions with low carbon content (IC and ICP-MS. The accuracy was evaluated using a certified reference material of polymer for Cl, Br and S and spike recovery experiments for all analytes. No statistical difference (t-test, 95% of confidence level) was observed between the results obtained for Cl, Br and S by IC after MIC and the certified values. In addition, spike recoveries obtained for F, Cl, Br, I and S ranged from 94% to 101%. The proposed method was suitable for polyimide decomposition for further determination of halogens and sulfur by IC and by ICP-MS (Br and I only). Taking into account the lack of methods and the difficulty of bringing this material into solution, MIC can be considered as a suitable alternative for the decomposition of polyimide for routine quality control of halogens and sulfur using IC or ICP-MS.

  12. Influence of Ta Content in High Purity Niobium on Cavity Performance Preliminary Results*

    CERN Document Server

    Kneisel, P

    2004-01-01

    In a previous paper* a program designed to study the influence of the residual tantalum content on the superconducting properties of pure niobium metal for RF cavities was outlined. The main rationale for this program was based on a potential cost reduction for high purity niobium, if a less strict limit on the chemical specification for Ta content, which is not significantly affecting the RRR–value, could be tolerated for high performance cavities. Four ingots with different Ta contents have been melted and transformed into sheets. In each manufacturing step the quality of the material has been monitored by employing chemical analysis, neutron activation analysis, thermal conductivity measurements and evaluation of the mechanical properties. The niobium sheets have been scanned for defects by an eddy current device. From three of the four ingots—Ta contents 100, 600 and 1,200 wppm—two single cell cavities each of the CEBAF variety have been fabricated and a series of tests on each ...

  13. Digitally synthesized high purity, high-voltage radio frequency drive electronics for mass spectrometry

    Science.gov (United States)

    Schaefer, R. T.; MacAskill, J. A.; Mojarradi, M.; Chutjian, A.; Darrach, M. R.; Madzunkov, S. M.; Shortt, B. J.

    2008-09-01

    Reported herein is development of a quadrupole mass spectrometer controller (MSC) with integrated radio frequency (rf) power supply and mass spectrometer drive electronics. Advances have been made in terms of the physical size and power consumption of the MSC, while simultaneously making improvements in frequency stability, total harmonic distortion, and spectral purity. The rf power supply portion of the MSC is based on a series-resonant LC tank, where the capacitive load is the mass spectrometer itself, and the inductor is a solenoid or toroid, with various core materials. The MSC drive electronics is based on a field programmable gate array (FPGA), with serial peripheral interface for analog-to-digital and digital-to-analog converter support, and RS232/RS422 communications interfaces. The MSC offers spectral quality comparable to, or exceeding, that of conventional rf power supplies used in commercially available mass spectrometers; and as well an inherent flexibility, via the FPGA implementation, for a variety of tasks that includes proportional-integral derivative closed-loop feedback and control of rf, rf amplitude, and mass spectrometer sensitivity. Also provided are dc offsets and resonant dipole excitation for mass selective accumulation in applications involving quadrupole ion traps; rf phase locking and phase shifting for external loading of a quadrupole ion trap; and multichannel scaling of acquired mass spectra. The functionality of the MSC is task specific, and is easily modified by simply loading FPGA registers or reprogramming FPGA firmware.

  14. Quantification of Trace Amounts of Impurities in High Purity Cobalt by High Resolution Inductively Coupled Plasma Mass Spectrometry

    Institute of Scientific and Technical Information of China (English)

    Hua Lin XIE; Xi Du NIE; You Gen TANG

    2006-01-01

    An analytical method using high resolution inductively coupled plasma mass spectrometry (HR-ICP-MS) for rapid simultaneous determination of Be, Mg, Al, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Ga, Ge, As, Se, Mo, Ag, Cd, Sn, Sb, Ba, Pt, Au and Pb in high purity cobalt was described. Sample digestions were performed in closed microwave vessels using HNO3 and HCl. The matrix effects due to thc presence of excess HCl and Co were evaluated. The usefulness of high mass resolution for overcoming some spectral interference was demonstrated. The optimum conditions for the determination was tested and discussed. Correction for matrix effects, Sc, Rh and Bi were used as internal standards. The detection limits is 0.003-0.57 μg/g, the recovery ratio is 92.2%- 111.2%, and the RSD is less than 3.6%. The method is accurate, quick and convenient. It has been applied to the determination of trace impurities in high purity cobalt with satisfactory results.

  15. Quantification of trace amounts of impurities in high purity cobalt by high resolution inductively coupled plasma mass spectrometry

    Institute of Scientific and Technical Information of China (English)

    XIE Hualin; HUANG Kelong; NIE Xidu; TANG Yougen

    2007-01-01

    An analytical method using high resolution inductively coupled plasma mass spectrometry (HR-ICP-MS) for rapid simultaneous determination of 24 elements (Be, Mg, Al, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Ga, Ge, As, Se, Mo, Ag, Cd, Sn,Sb, Ba, Pt, Au, and Pb) in high purity cobalt was described. Sample digestions were performed in closed microwave vessels using HNO3 and HCl. The matrix effects because of the presence of excess HCl and Co were evaluated. The usefulness of high mass resolution for overcoming some spectral interference was demonstrated. The optimum conditions for the determination were tested and discussed. The standard addition method was employed for quantitative analysis. The detection limits were 0.016-1.50 μg.g-1, the recovery ratios were 92.2%-111.2%, and the RSD was less than 3.6%. The method was accurate, quick, and convenient. It was applied to the determination of trace impurities in high purity cobalt with satisfactory results.

  16. Gadolinium-Induced Fibrosis.

    Science.gov (United States)

    Todd, Derrick J; Kay, Jonathan

    2016-01-01

    Gadolinium-based contrast agents (GBCAs), once believed to be safe for patients with renal disease, have been strongly associated with nephrogenic systemic fibrosis (NSF), a severe systemic fibrosing disorder that predominantly afflicts individuals with advanced renal dysfunction. We provide a historical perspective on the appearance and disappearance of NSF, including its initial recognition as a discrete clinical entity, its association with GBCA exposure, and the data supporting a causative relationship between GBCA exposure and NSF. On the basis of this body of evidence, we propose that the name gadolinium-induced fibrosis (GIF) more accurately reflects the totality of knowledge regarding this disease. Use of high-risk GBCAs, such as formulated gadodiamide, should be avoided in patients with renal disease. Restriction of GBCA use in this population has almost completely eradicated new cases of this debilitating condition. Emerging antifibrotic therapies may be useful for patients who suffer from GIF.

  17. Microhardness evolution and mechanical characteristics of commercial purity titanium processed by high-pressure torsion

    Energy Technology Data Exchange (ETDEWEB)

    Shirooyeh, Mahmood [Departments of Aerospace and Mechanical Engineering and Materials Science, University of Southern California, Los Angeles, CA 90089-1453 (United States); Xu, Jie [Departments of Aerospace and Mechanical Engineering and Materials Science, University of Southern California, Los Angeles, CA 90089-1453 (United States); Key Laboratory of Micro-systems and Micro-structures Manufacturing, Ministry of Education, Harbin Institute of Technology, Harbin 150080 (China); Langdon, Terence G., E-mail: langdon@usc.edu [Departments of Aerospace and Mechanical Engineering and Materials Science, University of Southern California, Los Angeles, CA 90089-1453 (United States); Materials Research Group, Faculty of Engineering and the Environment, University of Southampton, Southampton SO17 1BJ (United Kingdom)

    2014-09-22

    An investigation was conducted to evaluate the microstructural evolution and mechanical properties of a commercial purity (CP) titanium (grade 2) processed by high-pressure torsion (HPT) at room temperature. Microstructural analysis was performed to provide detailed information on the effect of shear strain on the grain size. The results demonstrate that significant grain refinement is achieved through HPT processing with a reduction from ∼45 μm in the initial annealed condition to a grain size of ∼150 nm after 10 turns of HPT. Measurements of the Vickers microhardness show that the disks are essentially homogeneous after 5 or more turns of torsional straining. Analysis by X-ray diffraction (XRD) revealed an allotropic phase transformation from the α-phase (hexagonal closed-packed) to the ω-phase (hexagonal) during HPT processing. The results from mechanical testing at an elevated temperature of 673 K are consistent with the microstructural observations thereby showing that ultra-fine grained CP Ti exhibits excellent mechanical properties.

  18. Determination of nitrogen monoxide in high purity nitrogen gas with an atmospheric pressure ionization mass spectrometer

    Science.gov (United States)

    Kato, K.

    1985-01-01

    An atmospheric pressure ionization mass spectrometric (API-MS) method was studied for the determination of residual NO in high purity N2 gas. The API-MS is very sensitive to NO, but the presence of O2 interferes with the NO measurement. Nitrogen gas in cylinders as sample gas was mixed with NO standard gas and/or O2 standard gas, and then introduced into the API-MS. The calibration curves of NO and O2 has linearity in the region of 0 - 2 ppm, but the slopes changed with every cylinder. The effect of O2 on NO+ peak was additive and proportional to O2 concentration in the range of 0 - 0.5 ppm. The increase in NO+ intensity due to O2 was (0.07 - 0.13)%/O2, 1 ppm. Determination of NO and O2 was carried out by the standard addition method to eliminate the influence of variation of slopes. The interference due to O2 was estimated from the product of the O2 concentration and the ratio of slope A to Slope B. Slope A is the change in the NO+ intensity with the O2 concentration. Slope B is the intensity with O2 concentration.

  19. Electrical properties of as-grown and proton-irradiated high purity silicon

    Energy Technology Data Exchange (ETDEWEB)

    Krupka, Jerzy, E-mail: krupka@imio.pw.edu.pl [Institute of Microelectronics and Optoelectronics, Warsaw University of Technology, Koszykowa 75, 00-662 Warsaw (Poland); Karcz, Waldemar [Joint Institute for Nuclear Research, Joliot-Curie 6, 141980 Dubna (Russian Federation); Kamiński, Paweł [Institute of Electronic Materials Technology, Wólczyńska 13, 301-919 Warsaw (Poland); Jensen, Leif [Topsil Semiconductor Materials A/S, Siliciumvej 1, DK-3600 Frederikssund (Denmark)

    2016-08-01

    The complex permittivity of as-grown and proton-irradiated samples of high purity silicon obtained by the floating zone method was measured as a function of temperature at a few frequencies in microwave spectrum by employing the quasi TE{sub 011} and whispering gallery modes excited in the samples under test. The resistivity of the samples was determined from the measured imaginary part of the permittivity. The resistivity was additionally measured at RF frequencies employing capacitive spectroscopy as well as in a standard direct current experiment. The sample of as-grown material had the resistivity of ∼85 kΩ cm at room temperature. The sample irradiated with 23-MeV protons had the resistivity of ∼500 kΩ cm at 295 K and its behavior was typical of the intrinsic material at room and at elevated temperatures. For the irradiated sample, the extrinsic conductivity region is missing and at temperatures below 250 K hopping conductivity occurs. Thermal cycle hysteresis of the resistivity for the sample of as-grown material is observed. After heating and subsequent cooling of the sample, its resistivity decreases and then slowly (∼50 h) returns to the initial value.

  20. Interaction between a high purity magnesium surface and PCL and PLA coatings during dynamic degradation.

    Science.gov (United States)

    Chen, Ying; Song, Yang; Zhang, Shaoxiang; Li, Jianan; Zhao, Changli; Zhang, Xiaonong

    2011-04-01

    In this study, polycaprolactone (PCL) and polylactic acid (PLA) coatings were prepared on the surface of high purity magnesium (HPMs), respectively, and electrochemical and dynamic degradation tests were used to investigate the degradation behaviors of these polymer-coated HPMs. The experimental results indicated that two uniform and smooth polymer films with thicknesses between 15 and 20 µm were successfully prepared on the HPMs. Electrochemical tests showed that both PCL-coated and PLA-coated HPMs had higher free corrosion potentials (E(corr)) and smaller corrosion currents (I(corr)) in the modified simulated body fluid (m-SBF) at 37 °C, compared to those of the uncoated HPMs. Dynamic degradation tests simulating the flow conditions in coronary arteries were carried out on a specific test platform. The weight of the specimens and the pH over the tests were recorded to characterize the corrosion performance of those samples. The surfaces of the specimens after the dynamic degradation tests were also examined. The data implied that there was a special interaction between HPM and its polymer coatings during the dynamic degradation tests, which undermined the corrosion resistance of the coated HPMs. A model was proposed to illustrate the interaction between the polymer coatings and HPM. This study also suggested that this reciprocity may also exist on the implanted magnesium stents coated with biodegradable polymers, which is a potential obstacle for the further development of drug-eluting magnesium stents.

  1. Abridged acid-base wet-milling synthesis of high purity hydroyapatite

    Directory of Open Access Journals (Sweden)

    Sandi Carolina Ruiz-Mendoza

    2008-06-01

    Full Text Available There is a plethora of routes to produce hydroxyapatite(HA and in general calcium phosphates(CP but production usually leads to a mixture of several phases. Besides ionic contamination, most of these methods are cumbersome, restricted to small volumes of product and require a lot of thermal energy. The acid-base route eliminates foreign ions or additives and its only byproduct is water. Heterogeneous reaction drawback is that solid reactants do not easily come in contact with each other and therefore addition and stirring times become very lengthy and still the product is a mixture. The synthesis started from calcium hydroxide and phosphoric acid (PA. Ball milling was used to favor kinetics and stoichiometry. Six sets of PA addition, paddle stirring and ball milling times were used. Products were evaluated by X ray diffraction (XRD, Fourier Transform Infrared (FTIR, scanning electron microscopy (SEM, X ray fluorescence (XRF and Ca/P ratio. Chemical analysis for calcium proceeded through oxalate precipitate and phosphorus by the phosphomolibdate technique. A set of conditions yielding high purity HA was established.

  2. High purity ultrafine-grained nickel processed by dynamic plastic deformation: microstructure and mechanical properties

    Energy Technology Data Exchange (ETDEWEB)

    Farbaniec, Lukasz; Dirras, Guy [Universite Paris 13, Sorbonne Paris Cite LSPM-CNRS, 99, Avenue J. B. Clement, 93430 Villetaneuse (France); Abdul-Latif, Akrum [Laboratoire d' Ingenierie des Systemes Mecaniques et des Materiaux 3, Rue Fernand Hainaut, 93407 St. Ouen Cedex (France); Gubicza, Jeno [Department of Materials Physics, Eoetvoes Lorand University Budapest, P.O. Box 32, H-1518 (Hungary)

    2012-11-15

    Bulk ultrafine-grained samples are processed by dynamic plastic deformation at an average strain rate of 3.3 x 10{sup 2} s{sup -1} from bulk coarse-grained nickel with purity higher than 98.4 wt.%. The obtained microstructure is investigated by electron backscattering diffraction, transmission electron microscopy and X-ray line profile analysis. After dynamic deformation the microstructure evolves into submicron-size lamellar and subgrain structures. Evaluation of average grain size shows a heterogeneous microstructure along both the diameter and the thickness of the sample. X-ray line profile analysis reveals high dislocation density of about 13 {+-} 2 x 10{sup 14} m{sup -2} in the impacted material. The mechanical properties are investigated by means of uniaxial quasi-static compression tests conducted at room temperature. The stress-strain behavior of the impacted Ni depends on the location in the impacted disk and on the orientation of the compression axis relative to the impact direction. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  3. Optimization of extraction of high purity all-trans-lycopene from tomato pulp waste.

    Science.gov (United States)

    Poojary, Mahesha M; Passamonti, Paolo

    2015-12-01

    The aim of this work was to optimize the extraction of pure all-trans-lycopene from the pulp fractions of tomato processing waste. A full factorial design (FFD) consisting of four independent variables including extraction temperature (30-50 °C), time (1-60 min), percentage of acetone in n-hexane (25-75%, v/v) and solvent volume (10-30 ml) was used to investigate the effects of process variables on the extraction. The absolute amount of lycopene present in the pulp waste was found to be 0.038 mg/g. The optimal conditions for extraction were as follows: extraction temperature 20 °C, time 40 min, a solvent composition of 25% acetone in n-hexane (v/v) and solvent volume 40 ml. Under these conditions, the maximal recovery of lycopene was 94.7%. The HPLC-DAD analysis demonstrated that, lycopene was obtained in the all-trans-configuration at a very high purity grade of 98.3% while the amount of cis-isomers and other carotenoids were limited.

  4. Synthesis of high-purity Ti2AlN ceramic by hot pressing

    Institute of Scientific and Technical Information of China (English)

    YAN Ming; CHEN Yan-lin; MEI Bing-chu; ZHU Jiao-qun

    2008-01-01

    High-purity Ti2AlN ceramic was prepared at 1300 ℃ by hot pressing(HP) of Ti/Al/TiN powders in stoichiometric proportion. The sintered product was characterized using X-ray diffraction(XRD) and MDI Jade 5.0 software (Materials Data Inc, Liverpool, CA). Scanning electron microscopy(SEM) and electron probe micro-analysis(EPMA) coupled with energy-dispersive spectroscopy(EDS) were utilized to investigate the morphology characteristics. The results show that Ti2AlN phase is well-developed with a close and lamellar structure. The grains are plate-like with the size of 3-5 μm, thickness of 8-10 μm and elongated dimension. The density of Ti2AlN is measured to be 4.22 g/cm3, which reaches 97.9% of its theory value. The distribution of Ti2AlN grains is homogeneous.

  5. GELATIO: a general framework for modular digital analysis of high-purity Ge detector signals

    CERN Document Server

    Agostini, M; Zavarise, P; Volynets, O

    2011-01-01

    GELATIO is a new software framework for advanced data analysis and digital signal processing developed for the GERDA neutrinoless double beta decay experiment. The framework is tailored to handle the full analysis flow of signals recorded by high purity Ge detectors and photo-multipliers from the veto counters. It is designed to support a multi-channel modular and flexible analysis, widely customizable by the user either via human-readable initialization files or via a graphical interface. The framework organizes the data into a multi-level structure, from the raw data up to the condensed analysis parameters, and includes tools and utilities to handle the data stream between the different levels. GELATIO is implemented in C++. It relies upon ROOT and its extension TAM, which provides compatibility with PROOF, enabling the software to run in parallel on clusters of computers or many-core machines. It was tested on different platforms and benchmarked in several GERDA-related applications. A stable version is pr...

  6. Effect of Purity Levels on the High-Temperature Deformation Characteristics of Severely Deformed Titanium

    Science.gov (United States)

    Sajadifar, Seyed Vahid; Yapici, Guney Guven

    2017-03-01

    In the present investigation, high-temperature compression tests were conducted at strain rates of 0.001 to 0.1 s-1 and at temperatures of 873 K to 1173 K (600 °C to 900 °C) in order to study the hot deformation characteristics and dynamic softening mechanisms of two different grades of commercial purity titanium after severe plastic deformation. It was observed that the effects of deformation rate and temperature are significant on obtained flow stress curves of both grades. Higher compressive strength exhibited by grade 2 titanium at relatively lower deformation temperatures was attributed to the grain boundary characteristics in relation with its lower processing temperature. However, severely deformed grade 4 titanium demonstrated higher compressive strength at relatively higher deformation temperatures (above 800 °C) due to suppressed grain growth via oxygen segregation limiting grain boundary motion. Constitutive equations were established to model the flow behavior, and the validity of the predictions was demonstrated with decent agreement accompanied by average error levels less than 5 pct for all the deformation conditions.

  7. Simulation study comparing high-purity germanium and cadmium zinc telluride detectors for breast imaging

    Science.gov (United States)

    Campbell, D. L.; Peterson, T. E.

    2014-11-01

    We conducted simulations to compare the potential imaging performance for breast cancer detection with High-Purity Germanium (HPGe) and Cadmium Zinc Telluride (CZT) systems with 1% and 3.8% energy resolution at 140 keV, respectively. Using the Monte Carlo N-Particle (MCNP5) simulation package, we modelled both 5 mm-thick CZT and 10 mm-thick HPGe detectors with the same parallel-hole collimator for the imaging of a breast/torso phantom. Simulated energy spectra were generated, and planar images were created for various energy windows around the 140 keV photopeak. Relative sensitivity and scatter and the torso fractions were calculated along with tumour contrast and signal-to-noise ratios (SNR). Simulations showed that utilizing a ±1.25% energy window with an HPGe system better suppressed torso background and small-angle scattered photons than a comparable CZT system using a -5%/+10% energy window. Both systems provided statistically similar contrast and SNR, with HPGe providing higher relative sensitivity. Lowering the counts of HPGe images to match CZT count density still yielded equivalent contrast between HPGe and CZT. Thus, an HPGe system may provide equivalent breast imaging capability at lower injected radioactivity levels when acquiring for equal imaging time.

  8. MIS High-Purity Plutonium Oxide Metal Oxidation Product TS707001 (SSR123): Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Veirs, Douglas Kirk [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Stroud, Mary Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Berg, John M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Narlesky, Joshua Edward [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Worl, Laura Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Martinez, Max A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Carillo, Alex [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-08-09

    A high-purity plutonium dioxide material from the Material Identification and Surveillance (MIS) Program inventory has been studied with regard to gas generation and corrosion in a storage environment. Sample TS707001 represents process plutonium oxides from several metal oxidation operations as well as impure and scrap plutonium from Hanford that are currently stored in 3013 containers. After calcination to 950°C, the material contained 86.98% plutonium with no major impurities. This study followed over time, the gas pressure of a sample with nominally 0.5 wt% water in a sealed container with an internal volume scaled to 1/500th of the volume of a 3013 container. Gas compositions were measured periodically over a six year period. The maximum observed gas pressure was 138 kPa. The increase over the initial pressure of 80 kPa was primarily due to generation of nitrogen and carbon dioxide gas in the first six months. Hydrogen and oxygen were minor components of the headspace gas. At the completion of the study, the internal components of the sealed container showed signs of corrosion, including pitting.

  9. Doping inorganic ions to regulate bioactivity of Ca-P coating on bioabsorbable high purity magnesium

    Institute of Scientific and Technical Information of China (English)

    Hongliu Wu; Xiaonong Zhang; Ruopeng Zhang; Xiao Li; Jiahua Ni; Changli Zhao; Yang Song; Jiawei Wang; Shaoxiang Zhang; Yufeng Zheng

    2014-01-01

    Performance of biomaterials was strongly affected by their surface properties and could be designed artificially to meet specific biomedical requirements. In this study, F-(F), SiO42-(Si), or HCO3-(C)-doped Ca–P coatings were fabricated by biomimetic deposition on the surface of biodegradable high-purity magnesium (HP Mg). The crystalline phases, morphologies and compositions of Ca–P coatings had been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS). The biomineralization and corrosion resistance of doped Ca–P coatings had also been investigated. The results showed that the Ca–P coating with or without doped elements mainly contained the plate-like dicalcium phosphate dehydrate (DCPD) phase. The doped F, Si, or C changed the surface morphology of Ca–P coatings after mineralization. Doped F enhanced the mineralization of Ca–P coating, and doped Si retarded the mineralization of Ca–P coating. However, H2 evolution of HP Mg discs with different Ca–P coatings was close to 0.4–0.7 ml/cm2 after two-week immersion. That meant that the corrosion resistance of the Ca–P coatings with different or without doped elements did not change significantly.

  10. Production of high-purity neofructooligosaccharides by culture of Xanthophyllomyces dendrorhous.

    Science.gov (United States)

    Sheu, Dey-Chyi; Chang, Jan-Yi; Chen, Yan-Jen; Lee, Cheng-Wei

    2013-03-01

    Neofructooligosaccharides (neo-FOS) were produced in submerged cultures of Xanthophyllomyces dendrorhous. Among the various strains of X. dendrorhous that have intracellular (6)G-fructofuranosidase ((6)G-FFase), BCRC 21346 with high enzyme activity (3.60 U/mL) and BCRC 22367 with low enzyme activity (0.59 U/mL) were investigated in this work. Neo-FOS were generated in a 5-L jar fermenter at 20°C, 100rpm and 2vvm with the pH controlled at 6.9±0.1, using 250g/L of sucrose as the substrate. Through the catalytic action of X. dendrorhous(6)G-FFase on sucrose, monosaccharides as well as neo-FOS were produced. A portion of these monosaccharides was consumed by the yeast cells. However, the production of monosaccharides was low in concentration in culture with low (6)G-FFase activity, indicating they might be used up concurrently during the fermentation. Consequently, neo-FOS at a purity of up to 87.4% could be obtained.

  11. Synthesis of High Purity SiC Powder for High-resistivity SiC Single Crystals Growth

    Institute of Scientific and Technical Information of China (English)

    Li WANG; Xiaobu HU; Xiangang XU; Shouzheng JIANG; Lina NING; Minhua JIANG

    2007-01-01

    High purity silicon carbide (SiC) powder was synthesized in-situ by chemical reaction between silicon and carbon powder. In order to ensure that the impurity concentration of the resulting SiC powder is suitable for high-resistivity SiC single crystal growth, the preparation technology of SiC powder is different from that of SiC ceramic. The influence of the shape and size of carbon particles on the morphology and phase composition of the obtained SiC powder were discussed. The phase composition and morphology of the products were investigated by X-ray diffraction, Raman microspectroscopy and scanning electron microscopy. The results show that the composition of resulting SiC by in-situ synthesis from Si/C mixture strongly depends on the nature of the carbon source, which corresponds to the particle size and shape, as well as the preparation temperature. In the experimental conditions, flake graphite is more suitable for the synthesis of SiC powder than activated carbon because of its relatively smaller particle size and flake shape, which make the conversion more complete. The major phase composition of the full conversion products is β-SiC, with traces of α-SiC.Glow discharge mass spectroscopy measurements indicated that SiC powder synthesized with this chemical reaction method can meet the purity demand for the growth of high-resistivity SiC single crystals.

  12. Synthesis of high purity monoglycerides from crude glycerol and palm stearin

    Directory of Open Access Journals (Sweden)

    Pakamas Chetpattananondh

    2008-07-01

    Full Text Available The optimum conditions for the glycerolysis of palm stearin and crude glycerol derived from biodiesel process werefound to be a reaction temperature of 200oC with a molar ratio of crude glycerol to palm stearin of 2.5:1, and a reaction timeof 20 minutes. The yield and purity of monoglycerides obtained under these conditions was satisfactory as compared withthe glycerolysis of pure glycerol. To increase the purity of monoglycerides a two-step process, removal of residual glyceroland crystallization, was proposed instead of either vacuum or molecular distillation. Residual glycerol was removed byadding hydrochloric acid followed by washing with hot water. Optimum conditions for crystallization were achieved byusing isooctane as a solvent and a turbine impeller speed of 200 rpm at a crystallization temperature of 35oC. A purity notexceeding 99 percent of monoglycerides was obtained with monopalmitin as the major product.

  13. Production of High Purity Multi-Walled Carbon Nanotubes from Catalytic Decomposition of Methane

    Institute of Scientific and Technical Information of China (English)

    Kong Bee Hong; Aidawati Azlin Binti Ismail; Mohamed Ezzaham Bin Mohd Mahayuddin; Abdul Rahman Mohamed; Sharif Hussein Sharif Zein

    2006-01-01

    Acid-based purification process of multi-walled carbon nanotubes (MWNTs) produced via catalytic decomposition of methane with NiO/TiO2 as a catalyst is described. By combining the oxidation in air and the acid refluxes, the impurities, such as amorphous carbon, carbon nanoparticles, and the NiO/TiO2 catalyst, are eliminated. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) images confirm the removal of the impurities. The percentage of the carbon nanotubes purity was analyzed using thermal gravimetric analysis (TGA). Using this process, 99.9 wt% purity of MWNTs was obtained.

  14. Nano-laminate vs. direct deposition of high permittivity gadolinium scandate on silicon by high pressure sputtering

    Energy Technology Data Exchange (ETDEWEB)

    Feijoo, P.C., E-mail: pedronska@fis.ucm.es [Dpto. Física Aplicada III (Electricidad y Electrónica), Universidad Complutense de Madrid, Fac. de CC. Físicas. Av/Complutense S/N, E-28040 Madrid (Spain); Pampillón, M.A.; San Andrés, E. [Dpto. Física Aplicada III (Electricidad y Electrónica), Universidad Complutense de Madrid, Fac. de CC. Físicas. Av/Complutense S/N, E-28040 Madrid (Spain); Fierro, J.L.G. [Instituto de Catálisis y Petroleoquímica, Consejo Superior de Investigaciones Científicas, C/Marie Curie 2, E-28049 Cantoblanco (Spain)

    2015-10-30

    In this work we use the high pressure sputtering technique to deposit the high permittivity dielectric gadolinium scandate on silicon substrates. This nonconventional deposition technique prevents substrate damage and allows for growth of ternary compounds with controlled composition. Two different approaches were assessed: the first one consists of depositing the material directly from a stoichiometric GdScO{sub 3} target; in the second one, we anneal a nano-laminate of < 0.5 nm thick Gd{sub 2}O{sub 3} and Sc{sub 2}O{sub 3} films in order to control the composition of the scandate. Metal–insulator–semiconductor capacitors were fabricated with platinum gates for electrical characterization. Accordingly, we grew a Gd-rich Gd{sub 2−x}Sc{sub x}O{sub 3} film that, in spite of higher leakage currents, presents a better effective relative permittivity of 21 and lower density of defects. - Highlights: • GdScO is deposited on Si as a high permittivity dielectric by two procedures. • Films sputtered from GdScO{sub 3} target are Sc-rich and present thick interface SiO{sub x}. • Gd-rich GdScO is obtained from a nano-laminate sputtered from Sc{sub 2}O{sub 3} and Gd{sub 2}O{sub 3}. • Gd{sub 1.8}Sc{sub 0.2}O{sub 3} shows good effective permittivity and electrical properties.

  15. Porous and mesh alumina formed by anodization of high purity aluminum films at low anodizing voltage

    Energy Technology Data Exchange (ETDEWEB)

    Abd-Elnaiem, Alaa M., E-mail: alaa.abd-elnaiem@science.au.edu.eg [KACST-Intel Consortium Center of Excellence in Nano-manufacturing Applications (CENA), Riyadh (Saudi Arabia); Physics Department, Faculty of Science, Assiut University, Assiut 71516 (Egypt); Mebed, A.M. [Physics Department, Faculty of Science, Assiut University, Assiut 71516 (Egypt); Department of Physics, Faculty of Science, Al-Jouf University, Sakaka 2014 (Saudi Arabia); El-Said, Waleed Ahmed [Department of Chemistry, Faculty of Science, Assiut University, Assiut 71516 (Egypt); Abdel-Rahim, M.A. [Physics Department, Faculty of Science, Assiut University, Assiut 71516 (Egypt)

    2014-11-03

    Electrochemical oxidation of high-purity aluminum (Al) films under low anodizing voltages (1–10) V has been conducted to obtain anodic aluminum oxide (AAO) with ultra-small pore size and inter-pore distance. Different structures of AAO have been obtained e.g. nanoporous and mesh structures. Highly regular pore arrays with small pore size and inter-pore distance have been formed in oxalic or sulfuric acids at different temperatures (22–50 °C). It is found that the pore diameter, inter-pore distance and the barrier layer thickness are independent of the anodizing parameters, which is very different from the rules of general AAO fabrication. The brand formation mechanism has been revealed by the scanning electron microscope study. Regular nanopores are formed under 10 V at the beginning of the anodization and then serve as a template layer dominating the formation of ultra-small nanopores. Anodization that is performed at voltages less than 5 V leads to mesh structured alumina. In addition, we have introduced a simple one-pot synthesis method to develop thin walls of oxide containing lithium (Li) ions that could be used for battery application based on anodization of Al films in a supersaturated mixture of lithium phosphate and phosphoric acid as matrix for Li-composite electrolyte. - Highlights: • We develop anodic aluminum oxide (AAO) with small pore size and inter-pore distance. • Applying low anodizing voltages onto aluminum film leads to form mesh structures. • The value of anodizing voltage (1–10 V) has no effect on pore size or inter-pore distance. • Applying anodizing voltage less than 5 V leads to mesh structured AAO. • AAO can be used as a matrix for Li-composite electrolytes.

  16. Dielectric Performance of a High Purity HTCC Alumina at High Temperatures - a Comparison Study with Other Polycrystalline Alumina

    Science.gov (United States)

    Chen, Liangyu

    2014-01-01

    A very high purity (99.99+%) high temperature co-fired ceramic (HTCC) alumina has recently become commercially available. The raw material of this HTCC alumina is very different from conventional HTCC alumina, and more importantly there is no glass additive in this alumina material for co-firing processing. Previously, selected HTCC and LTCC (low temperature co-fired ceramic) alumina materials were evaluated at high temperatures as dielectric and compared to a regularly sintered 96% polycrystalline alumina (96% Al2O3), where 96% alumina was used as the benchmark. A prototype packaging system based on regular 96% alumina with Au thickfilm metallization successfully facilitated long term testing of high temperature silicon carbide (SiC) electronic devices for over 10,000 hours at 500 C. In order to evaluate this new high purity HTCC alumina for possible high temperature packaging applications, the dielectric properties of this HTCC alumina substrate were measured and compared with those of 96% alumina and a previously tested LTCC alumina from room temperature to 550 C at frequencies of 120 Hz, 1 KHz, 10 KHz, 100 KHz, and 1 MHz. A parallel-plate capacitive device with dielectric of the HTCC alumina and precious metal electrodes were used for measurements of the dielectric constant and dielectric loss of the co-fired alumina material in the temperature and frequency ranges. The capacitance and AC parallel conductance of the capacitive device were directly measured by an AC impedance meter, and the dielectric constant and parallel AC conductivity of the dielectric were calculated from the capacitance and conductance measurement results. The temperature and frequency dependent dielectric constant, AC conductivity, and dissipation factor of the HTCC alumina substrate are presented and compared to those of 96% alumina and a selected LTCC alumina. Other technical advantages of this new co-fired material for possible high packaging applications are also discussed.

  17. Development of High-purity Certified Reference Materials for 17 Proteinogenic Amino Acids by Traceable Titration Methods.

    Science.gov (United States)

    Kato, Megumi; Yamazaki, Taichi; Kato, Hisashi; Eyama, Sakae; Goto, Mari; Yoshioka, Mariko; Takatsu, Akiko

    2015-01-01

    To ensure the reliability of amino acid analyses, the National Metrology Institute of Japan of the National Institute of Advanced Industrial Science and Technology (NMIJ/AIST) has developed high-purity certified reference materials (CRMs) for 17 proteinogenic amino acids. These CRMs are intended for use as primary reference materials to enable the traceable quantification of amino acids. The purity of the present CRMs was determined based on two traceable methods: nonaqueous acidimetric titration and nitrogen determination by the Kjeldahl method. Since neither method could distinguish compounds with similar structures, such as amino acid-related impurities, impurities were thoroughly quantified by combining several HPLC methods, and subtracted from the obtained purity of each method. The property value of each amino acid was calculated as a weighted mean of the corrected purities by the two methods. The uncertainty of the property value was obtained by combining measurement uncertainties of the two methods, a difference between the two methods, the uncertainty from the contribution of impurities, and the uncertainty derived from inhomogeneity. The uncertainty derived from instability was considered to be negligible based on stability monitoring of some CRMs. The certified value of each amino acid, property value with uncertainty, was given for both with or without enantiomeric separation.

  18. Cross Purposes: Love and Purity at a Puerto Rican Protestant High School

    Science.gov (United States)

    Seale-Collazo, James

    2013-01-01

    A "native" Christian ethnographer finds religious education at this church-sponsored school to pursue two distinct, and occasionally conflicting, curricula: "love" and "purity." The curriculum of love draws on what Turner called liminality and communitas in an effort to promote spiritual "encounters with…

  19. Efficient continuous synthesis of high purity deep eutectic solvents by twin screw extrusion.

    Science.gov (United States)

    Crawford, D E; Wright, L A; James, S L; Abbott, A P

    2016-03-18

    Mechanochemical synthesis has been applied to the rapid synthesis of Deep Eutectic Solvents (DESs), including Reline 200 (choline chloride : urea, 1 : 2), in a continuous flow methodology by Twin Screw Extrusion (TSE). This gave products in higher purity and with Space Time Yields (STYs), four orders of magnitude greater than for batch methods.

  20. Raman and photoelectron spectroscopic investigation of high-purity niobium materials: Oxides, hydrides, and hydrocarbons

    Science.gov (United States)

    Singh, Nageshwar; Deo, M. N.; Nand, Mangla; Jha, S. N.; Roy, S. B.

    2016-09-01

    We present investigations of the presence of oxides, hydrides, and hydrocarbons in high-purity (residual resistivity ratio, ˜300) niobium (Nb) materials used in fabrication of superconducting radio frequency (SRF) cavities for particle accelerators. Raman spectroscopy of Nb materials (as-received from the vendor as well as after surface chemical- and thermal processing) revealed numerous peaks, which evidently show the presence of oxides (550 cm-1), hydrides (1277 and 1385 cm-1: ˜80 K temperature), and groups of hydrocarbons (1096, 2330, 2710, 2830, 2868, and 3080 cm-1). The present work provides direct spectroscopic evidence of hydrides in the electropolished Nb materials typically used in SRF cavities. Raman spectroscopy thus can provide vital information about the near-surface chemical species in niobium materials and will help in identifying the cause for the performance degradation of SRF cavities. Furthermore, photoelectron spectroscopy was performed on the Nb samples to complement the Raman spectroscopy study. This study reveals the presence of C and O in the Nb samples. Core level spectra of Nb (doublet 3d5/2 and 3d3/2) show peaks near 206.6 and 209.4 eV, which can be attributed to the Nb5+ oxidation state. The core level spectra of C 1 s of the samples are dominated by graphitic carbon (binding energy, 284.6 eV), while the spectra of O 1 s are asymmetrically peaked near binding energy of ˜529 eV, and that indicates the presence of metal-oxide Nb2O5. The valence-band spectra of the Nb samples are dominated by a broad peak similar to O 2p states, but after sputtering (for 10 min) a peak appears at ˜1 eV, which is a feature of the elemental Nb atom.

  1. Evaluation of Prebiotic Effects of High-Purity Galactooligosaccharides in vitro and in vivo

    Directory of Open Access Journals (Sweden)

    Ki Bae Hong

    2016-01-01

    Full Text Available Galactooligosaccharides (GOS are an important class of dietary prebiotics that exert beneficial effects on intestinal microbiota and gut barrier function. In this study, high-purity GOS (HP-GOS were investigated in vitro and in vivo and confirmed as prebiotic ingredients in rat diet. HP-GOS were successfully produced using a two-step process, enzymatic hydrolysis and fermentation by yeast. They were found to serve as a good substrate and carbon source for supporting the growth of probiotic bacteria more effectively than other commercial GOS. Following administration of 1 % (by mass of HP-GOS to rats, the growth of Bifidobacterium bifidum and B. longum in the gut increased most rapidly up to 12 h, and thereafter the increase was slow. Therefore, 1 % HP-GOS was found to be acceptable for the growth of probiotic bacteria. Groups of animals that were orally administered HP-GOS and bifidobacteria during the study, and the group administered HP-GOS during the 2nd (days 13–15 and 4th (days 28–30 period of the study had significantly (p<0.05 higher numbers of bifidobacteria in faeces than groups receiving a single dose of bifidobacteria. HP-GOS affected the expression of genes encoding glucagon-like peptide-1 (GLP-1 and peptide YY (PYY. There was a significant upregulation of GLP-1 and PYY mRNA with HP-GOS and bifidobacteria intake. We propose that the prebiotic properties of HP-GOS are potentially valuable for the production of functional foods for human consumption.

  2. High-Purity Aluminum Magnet Technology for Advanced Space Transportation Systems

    Science.gov (United States)

    Goodrich, R. G.; Pullam, B.; Rickle, D.; Litchford, R. J.; Robertson, G. A.; Schmidt, D. D.; Cole, John (Technical Monitor)

    2001-01-01

    Basic research on advanced plasma-based propulsion systems is routinely focused on plasmadynamics, performance, and efficiency aspects while relegating the development of critical enabling technologies, such as flight-weight magnets, to follow-on development work. Unfortunately, the low technology readiness levels (TRLs) associated with critical enabling technologies tend to be perceived as an indicator of high technical risk, and this, in turn, hampers the acceptance of advanced system architectures for flight development. Consequently, there is growing recognition that applied research on the critical enabling technologies needs to be conducted hand in hand with basic research activities. The development of flight-weight magnet technology, for example, is one area of applied research having broad crosscutting applications to a number of advanced propulsion system architectures. Therefore, NASA Marshall Space Flight Center, Louisiana State University (LSU), and the National High Magnetic Field Laboratory (NHMFL) have initiated an applied research project aimed at advancing the TRL of flight-weight magnets. This Technical Publication reports on the group's initial effort to demonstrate the feasibility of cryogenic high-purity aluminum magnet technology and describes the design, construction, and testing of a 6-in-diameter by 12-in-long aluminum solenoid magnet. The coil was constructed in the machine shop of the Department of Physics and Astronomy at LSU and testing was conducted in NHMFL facilities at Florida State University and at Los Alamos National Laboratory. The solenoid magnet was first wound, reinforced, potted in high thermal conductivity epoxy, and bench tested in the LSU laboratories. A cryogenic container for operation at 77 K was also constructed and mated to the solenoid. The coil was then taken to NHMFL facilities in Tallahassee, FL. where its magnetoresistance was measured in a 77 K environment under steady magnetic fields as high as 10 T. In

  3. Engineering of high purity ultra-long optical needle field through reversing the electric dipole array radiation.

    Science.gov (United States)

    Wang, Jiming; Chen, Weibin; Zhan, Qiwen

    2010-10-11

    We report a new method to create high purity longitudinally polarized field with extremely long depth of focus in the focal volume of a high numerical aperture (NA) objective lens. Through reversing the radiated field from an electric dipole array situated near the focus of the high-NA lens, the required incident field distribution in the pupil plane for the creation of an ultra-long optical needle field can be found. Numerical examples demonstrate that an optical needle field with a depth of focus up to 8λ is obtainable. Throughout the depth of focus, this engineered focal field maintains a diffraction limited transverse spot size (<0.43λ) with high longitudinal polarization purity. From the calculated pupil plane distribution, a simplified discrete complex pupil filter can be designed and significant improvements over the previously reported complex filters are clearly demonstrated.

  4. Diffusion bonding and brazing of high purity copper for linear collider accelerator structures

    Directory of Open Access Journals (Sweden)

    J. W. Elmer

    2001-05-01

    Full Text Available Diffusion bonding and brazing of high purity copper were investigated to develop procedures for joining precision machined copper components for the Next Linear Collider (NLC. Diffusion bonds were made over a range of temperatures from 400 °C to 1000 °C, under two different loading conditions [3.45 kPa (0.5 psi and 3.45 MPa (500 psi], and on two different diamond machined surface finishes. Brazes were made using pure silver, pure gold, and gold-nickel alloys, and different heating rates produced by both radiation and induction heating. Braze materials were applied by both physical vapor deposition (PVD and conventional braze alloy shims. Results of the diffusion bonding experiments showed that bond strengths very near that of the copper base metal could be made at bonding temperatures of 700 °C or higher at 3.45 MPa bonding pressure. At lower temperatures, only partial strength diffusion bonds could be made. At low bonding pressures (3.45 kPa, full strength bonds were made at temperatures of 800 °C and higher, while no bonding (zero strength was observed at temperatures of 700 °C and lower. Observations of the fracture surfaces of the diffusion bonded samples showed the effects of surface finish on the bonding mechanism. These observations clearly indicate that bonding began by point asperity contact, and flatter surfaces resulted in a higher percentage of bonded area under similar bonding conditions. Results of the brazing experiments indicated that pure silver worked very well for brazing under both conventional and high heating rate scenarios. Similarly, pure silver brazed well for both the PVD layers and the braze alloy shims. The gold and gold-containing brazes had problems, mainly due to the high diffusivity of gold in copper. These problems led to the necessity of overdriving the temperature to ensure melting, the presence of porosity in the joint, and very wide braze joints. Based on the overall findings of this study, a two

  5. Ultra high molecular weight polyethylene (UHMWPE) fiber epoxy composite hybridized with Gadolinium and Boron nanoparticles for radiation shielding

    Science.gov (United States)

    Mani, Venkat; Prasad, Narasimha S.; Kelkar, Ajit

    2016-09-01

    Deep space radiations pose a major threat to the astronauts and their spacecraft during long duration space exploration missions. The two sources of radiation that are of concern are the galactic cosmic radiation (GCR) and the short lived secondary neutron radiations that are generated as a result of fragmentation that occurs when GCR strikes target nuclei in a spacecraft. Energy loss, during the interaction of GCR and the shielding material, increases with the charge to mass ratio of the shielding material. Hydrogen with no neutron in its nucleus has the highest charge to mass ratio and is the element which is the most effective shield against GCR. Some of the polymers because of their higher hydrogen content also serve as radiation shield materials. Ultra High Molecular Weight Polyethylene (UHMWPE) fibers, apart from possessing radiation shielding properties by the virtue of the high hydrogen content, are known for extraordinary properties. An effective radiation shielding material is the one that will offer protection from GCR and impede the secondary neutron radiations resulting from the fragmentation process. Neutrons, which result from fragmentation, do not respond to the Coulombic interaction that shield against GCR. To prevent the deleterious effects of secondary neutrons, targets such as Gadolinium are required. In this paper, the radiation shielding studies that were carried out on the fabricated sandwich panels by vacuum-assisted resin transfer molding (VARTM) process are presented. VARTM is a manufacturing process used for making large composite structures by infusing resin into base materials formed with woven fabric or fiber using vacuum pressure. Using the VARTM process, the hybridization of Epoxy/UHMWPE composites with Gadolinium nanoparticles, Boron, and Boron carbide nanoparticles in the form of sandwich panels were successfully carried out. The preliminary results from neutron radiation tests show that greater than 99% shielding performance was

  6. Hybrid microfiber-lithium-niobate nanowaveguide structures as high-purity heralded single-photon sources

    Science.gov (United States)

    Main, Philip; Mosley, Peter J.; Ding, Wei; Zhang, Lijian; Gorbach, Andrey V.

    2016-12-01

    We propose a compact, fiber-integrated architecture for photon-pair generation by parametric downconversion with unprecedented flexibility in the properties of the photons produced. Our approach is based on a thin-film lithium niobate nanowaveguide, evanescently coupled to a tapered silica microfiber. We demonstrate how controllable mode hybridization between the fiber and waveguide yields control over the joint spectrum of the photon pairs. We also investigate how independent engineering of the linear and nonlinear properties of the structure can be achieved through the addition of a tapered, proton-exchanged layer to the waveguide. This allows further refinement of the joint spectrum through custom profiling of the effective nonlinearity, drastically improving the purity of the heralded photons. We give details of a source design capable of generating heralded single photons in the telecom wavelength range with purity of at least 0.95, and we provide a feasible fabrication methodology.

  7. Equilibrium between titanium ions and high-purity titanium electrorefining in a NaCl-KCl melt

    Institute of Scientific and Technical Information of China (English)

    Jian-xun Song; Qiu-yu Wang; Guo-jing Hu; Xiao-bo Zhu; Shu-qiang Jiao; Hong-min Zhu

    2014-01-01

    TiClx (x=2.17) was prepared by using titanium sponge to reduce the concentration of TiCl4 in a NaCl−KCl melt under negative pressure. The as-prepared NaCl−KCl−TiClx melt was employed as the electrolyte, and two parallel crude titanium plates and one high-purity titanium plate were used as the anode and cathode, respectively. A series of electrochemical tests were performed to investigate the influence of electrolytic parameters on the current efficiency and quality of cathodic products. The results indicated that the quality of cathodic prod-ucts was related to the current efficiency, which is significantly dependent on the current density and the initial concentration of titanium ions. The significance of this study is the attainment of high-purity titanium with a low oxygen content of 30 × 10−6.

  8. Potential utility of eGFP-expressing NOG mice (NOG-EGFP as a high purity cancer sampling system

    Directory of Open Access Journals (Sweden)

    Shima Kentaro

    2012-06-01

    Full Text Available Abstract Purpose It is still technically difficult to collect high purity cancer cells from tumor tissues, which contain noncancerous cells. We hypothesized that xenograft models of NOG mice expressing enhanced green fluorescent protein (eGFP, referred to as NOG-EGFP mice, may be useful for obtaining such high purity cancer cells for detailed molecular and cellular analyses. Methods Pancreato-biliary cancer cell lines were implanted subcutaneously to compare the tumorigenicity between NOG-EGFP mice and nonobese diabetic/severe combined immunodeficiency (NOD/SCID mice. To obtain high purity cancer cells, the subcutaneous tumors were harvested from the mice and enzymatically dissociated into single-cell suspensions. Then, the cells were sorted by fluorescence-activated cell sorting (FACS for separation of the host cells and the cancer cells. Thereafter, the contamination rate of host cells in collected cancer cells was quantified by using FACS analysis. The viability of cancer cells after FACS sorting was evaluated by cell culture and subsequent subcutaneous reimplantation in NOG-EGFP mice. Results The tumorigenicity of NOG-EGFP mice was significantly better than that of NOD/SCID mice in all of the analyzed cell lines (p  Conclusions This method provides a novel cancer sampling system for molecular and cellular analysis with high accuracy and should contribute to the development of personalized medicine.

  9. High sensitivity of late gadolinium enhancement for predicting microscopic myocardial scarring in biopsied specimens in hypertrophic cardiomyopathy.

    Directory of Open Access Journals (Sweden)

    Tetsuo Konno

    Full Text Available BACKGROUND: Myocardial scarring can be assessed by cardiac magnetic resonance imaging with late gadolinium enhancement and by endomyocardial biopsy. However, accuracy of late gadolinium enhancement for predicting microscopic myocardial scarring in biopsied specimens remains unknown in hypertrophic cardiomyopathy. We investigated whether late gadolinium enhancement in the whole heart reflects microscopic myocardial scarring in the small biopsied specimens in hypertrophic cardiomyopathy. METHODS AND RESULTS: Twenty-one consecutive patients with hypertrophic cardiomyopathy who were examined both by cardiac magnetic resonance imaging and by endomyocardial biopsy were retrospectively studied. The right interventricular septum was the target site for endomyocardial biopsy in all patients. Late gadolinium enhancement in the ventricular septum had an excellent sensitivity (100% with a low specificity (40% for predicting microscopic myocardial scarring in biopsied specimens. The sensitivity of late gadolinium enhancement in the whole heart remained 100% with a specificity of 27% for predicting microscopic myocardial scarring in biopsied specimens. Quantitative assessments of fibrosis revealed that the extent of late gadolinium enhancement in the whole heart was the only independent variable related to the microscopic collagen fraction in biopsied specimens (β  =  0.59, 95% confident interval: 0.15 - 1.0, p  =  0.012. CONCLUSIONS: Although there was a compromise in the specificity, the sensitivity of late gadolinium enhancement was excellent for prediction of microscopic myocardial scarring in hypertrophic cardiomyopathy. Moreover, the severity of late gadolinium enhancement was independently associated with the quantitative collagen fraction in biopsied specimens in hypertrophic cardiomyopathy. These findings indicate that late gadolinium enhancement can reflect both the presence and the extent of microscopic myocardial scarring in the small

  10. High sensitivity of late gadolinium enhancement for predicting microscopic myocardial scarring in biopsied specimens in hypertrophic cardiomyopathy.

    Science.gov (United States)

    Konno, Tetsuo; Hayashi, Kenshi; Fujino, Noboru; Nagata, Yoji; Hodatsu, Akihiko; Masuta, Eiichi; Sakata, Kenji; Nakamura, Hiroyuki; Kawashiri, Masa-aki; Yamagishi, Masakazu

    2014-01-01

    Myocardial scarring can be assessed by cardiac magnetic resonance imaging with late gadolinium enhancement and by endomyocardial biopsy. However, accuracy of late gadolinium enhancement for predicting microscopic myocardial scarring in biopsied specimens remains unknown in hypertrophic cardiomyopathy. We investigated whether late gadolinium enhancement in the whole heart reflects microscopic myocardial scarring in the small biopsied specimens in hypertrophic cardiomyopathy. Twenty-one consecutive patients with hypertrophic cardiomyopathy who were examined both by cardiac magnetic resonance imaging and by endomyocardial biopsy were retrospectively studied. The right interventricular septum was the target site for endomyocardial biopsy in all patients. Late gadolinium enhancement in the ventricular septum had an excellent sensitivity (100%) with a low specificity (40%) for predicting microscopic myocardial scarring in biopsied specimens. The sensitivity of late gadolinium enhancement in the whole heart remained 100% with a specificity of 27% for predicting microscopic myocardial scarring in biopsied specimens. Quantitative assessments of fibrosis revealed that the extent of late gadolinium enhancement in the whole heart was the only independent variable related to the microscopic collagen fraction in biopsied specimens (β  =  0.59, 95% confident interval: 0.15 - 1.0, p  =  0.012). Although there was a compromise in the specificity, the sensitivity of late gadolinium enhancement was excellent for prediction of microscopic myocardial scarring in hypertrophic cardiomyopathy. Moreover, the severity of late gadolinium enhancement was independently associated with the quantitative collagen fraction in biopsied specimens in hypertrophic cardiomyopathy. These findings indicate that late gadolinium enhancement can reflect both the presence and the extent of microscopic myocardial scarring in the small biopsied specimens in hypertrophic cardiomyopathy.

  11. Gas and RRR distribution in high purity Niobium EB welded in Ultra-High Vacuum

    Science.gov (United States)

    Anakhov, S.; Singer, X.; Singer, W.; Wen, H.

    2006-05-01

    Electron beam (EB) welding in UHV (ultra-high vacuum, 10-5÷10-8 mbar) is applied in the standard fabrication of high gradient niobium superconducting radio frequency (SRF) cavities of TESLA design. The quality of EB welding is critical for cavity performance. Experimental data of gas content (H2, O2, N2) and RRR (residual resistivity ratio) measurements in niobium (Nb) welding seams are presented. EB welding in UHV conditions allow to preserve low gas content (1÷3 wt. ppm hydrogen and 5÷7 ppm oxygen and nitrogen), essential for high values of RRR — 350÷400 units. Gas content redistribution in the electron beam welded and heat affected region take place in the welding process. Correlation between gas solubility parameters, RRR and thermal conductivity are presented. Mechanisms of gas solubility in EB welding process are discussed.

  12. Gas and RRR Distribution in High Purity Niobium EB Welded in Ultra-High Vacuum.

    OpenAIRE

    Anakhov, S.; Singer, X.; W. Singer; Wen, H.

    2006-01-01

    Electron beam (EB) welding in UHV (ultra-high vacuum, 10(-5) divided by 10(-8) mbar) is applied in the standard fabrication of high gradient niobium superconducting radio frequency (SRF) cavities of TESLA design. The quality of EB welding is critical for cavity performance. Experimental data of gas content (H-2, O-2, N-2) and RRR (residual resistivity ratio) measurements in niobium (Nb) welding seams are presented. EB welding in UHV conditions allow to preserve low gas content (1 divided by 3...

  13. Methods to improve and understand the sensitivity of high purity germanium detectors for searches of rare events

    Energy Technology Data Exchange (ETDEWEB)

    Volynets, Oleksandr

    2012-07-27

    Observation of neutrinoless double beta-decay could answer fundamental questions on the nature of neutrinos. High purity germanium detectors are well suited to search for this rare process in germanium. Successful operation of such experiments requires a good understanding of the detectors and the sources of background. Possible background sources not considered before in the presently running GERDA high purity germanium detector experiment were studied. Pulse shape analysis using artificial neural networks was used to distinguish between signal-like and background-like events. Pulse shape simulation was used to investigate systematic effects influencing the efficiency of the method. Possibilities to localize the origin of unwanted radiation using Compton back-tracking in a granular detector system were examined. Systematic effects in high purity germanium detectors influencing their performance have been further investigated using segmented detectors. The behavior of the detector response at different operational temperatures was studied. The anisotropy effects due to the crystallographic structure of germanium were facilitated in a novel way to determine the orientation of the crystallographic axes.

  14. Generation of High Purity Photon-Pair in a Short Highly Non-Linear Fiber

    Science.gov (United States)

    2013-01-01

    of entangled photon pairs in optical fiber attracted enormous interest due to its better spatial mode definition and inherent compatibility with...existing fiber optics technologies for long distance transmission, storage and processing. Entangled photon pair generation in optical fiber is...nonlinear microstructure fiber (HNMSF) [7]. In contrast, entangled photon pair generation at telecom wavelengths via SFWM using highly nonlinear fiber

  15. Non-iridescent Transmissive Structural Color Filter Featuring Highly Efficient Transmission and High Excitation Purity

    OpenAIRE

    2014-01-01

    Nanostructure based color filtering has been considered an attractive replacement for current colorant pigmentation in the display technologies, in view of its increased efficiencies, ease of fabrication and eco-friendliness. For such structural filtering, iridescence relevant to its angular dependency, which poses a detrimental barrier to the practical development of high performance display and sensing devices, should be mitigated. We report on a non-iridescent transmissive structural color...

  16. Effects of electric field on recrystallization texture evolution in cold-rolled high-purity aluminum sheet during annealing

    Institute of Scientific and Technical Information of China (English)

    WU Yan; ZHAO Xiang; HE Chang-shu; ZHAO Zhi-peng; ZUO Liang; C. ESLING

    2007-01-01

    The effects of an external DC (direct current) electric field on recrystallization texture evolution in the cold-rolled aluminum sheets with 99.99% purity were investigated by means of X-ray diffraction techniques. The cold-rolled high-purity aluminum sheets were annealed for 60 min at 200, 300 and 400 ℃, respectively with and without an external DC electric field of 800 V/mm. The results show that with DC electric field, the recrystallization cube texture is strengthened at the stage of grain growth. Possible reason for the strengthening of the recrystallization cube texture with the applied electric field may be attributed to both selected nucleation and selected growth of cube oriented crystal nuclei.

  17. Ultra-thin films with highly absorbent porous media fine-tunable for coloration and enhanced color purity.

    Science.gov (United States)

    Yoo, Young Jin; Lim, Jin Ha; Lee, Gil Ju; Jang, Kyung-In; Song, Young Min

    2017-03-02

    We demonstrate ultra-thin, fine-tunable optical coatings with enhanced color purity based on highly absorbent porous media on a metal substrate. We show that the color range provided by these ultra-thin film coatings can be extended by making the absorptive dielectric layer porous. Oblique angle deposition (OAD) of a thin (10-25 nm) germanium (Ge) film by e-beam evaporation onto a thick gold substrate yields controlled porosity. Reflectance spectra and color representations from both calculations and experiments verify the enhancement of resonance tunability and color purity in the nano-tailored coatings. Angle independent reflection properties, and the applicability of such porous Ge on various metal substrates, indicate the strength of these concepts.

  18. Photocatalytic Degradation of Rhodamine B Dye with High Purity Anatase Nano-TiO2 Synthesized by a Hydrothermal Method

    Institute of Scientific and Technical Information of China (English)

    SHI Xiaoliang; YANG Xingyong; WANG Shuwei; WANG Sheng; ZHANG Qiaoxin; WANG Yufu

    2011-01-01

    High purity anatase nano-TiO2 powders with high photocatalytic activity were prepared by a hydrothermal synthesis method.X-ray diffraction(XRD),field emission transmission electron microscopy (FETEM),ultraviolet-visible(UV-Vis)light absorption spectrum and photoluminescence(PL)spectrum were adopted to characterize the catalyst.Effects of temperature,time and sol concentration of hydrothermal synthesis on particle size and phases were investigated.Photocatalytic activities in the degradation of Rhodamine B Dye were studied.The experimental results indicated that photocatalytic activity of the nano-TiO2 powers was much higher than that of P25(Degussa).

  19. Considering Process Nonlinearity in Dual-Point Composition Control of a High-Purity Ideal Heat Integrated Distillation Column

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Dual-point composition control for a high-purity ideal heat integrated distillation column (HIDiC) is addressed in this work. Three measures are suggested and combined for overcoming process inherent nonlinearities:(1) variable scaling; (2) multi-model representation of process dynamics and (3) feedforward compensation. These strategies can offer the developed control systems with several distinct advantages: (1) capability of dealing with severe disturbances; (2) tight tuning of controller parameters and (3) high robustness with respect to variation of operating conditions. Simulation results demonstrate the effectiveness of the proposed methodology.

  20. High Purity Hydrogen Production with In-Situ Carbon Dioxide and Sulfur Capture in a Single Stage Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Nihar Phalak; Shwetha Ramkumar; Daniel Connell; Zhenchao Sun; Fu-Chen Yu; Niranjani Deshpande; Robert Statnick; Liang-Shih Fan

    2011-07-31

    Enhancement in the production of high purity hydrogen (H{sub 2}) from fuel gas, obtained from coal gasification, is limited by thermodynamics of the water gas shift (WGS) reaction. However, this constraint can be overcome by conducting the WGS in the presence of a CO{sub 2}-acceptor. The continuous removal of CO{sub 2} from the reaction mixture helps to drive the equilibrium-limited WGS reaction forward. Since calcium oxide (CaO) exhibits high CO{sub 2} capture capacity as compared to other sorbents, it is an ideal candidate for such a technique. The Calcium Looping Process (CLP) developed at The Ohio State University (OSU) utilizes the above concept to enable high purity H{sub 2} production from synthesis gas (syngas) derived from coal gasification. The CLP integrates the WGS reaction with insitu CO{sub 2}, sulfur and halide removal at high temperatures while eliminating the need for a WGS catalyst, thus reducing the overall footprint of the hydrogen production process. The CLP comprises three reactors - the carbonator, where the thermodynamic constraint of the WGS reaction is overcome by the constant removal of CO{sub 2} product and high purity H{sub 2} is produced with contaminant removal; the calciner, where the calcium sorbent is regenerated and a sequestration-ready CO{sub 2} stream is produced; and the hydrator, where the calcined sorbent is reactivated to improve its recyclability. As a part of this project, the CLP was extensively investigated by performing experiments at lab-, bench- and subpilot-scale setups. A comprehensive techno-economic analysis was also conducted to determine the feasibility of the CLP at commercial scale. This report provides a detailed account of all the results obtained during the project period.

  1. Dielectric Performance of High Purity HTCC Alumina at High Temperatures - A Comparison Study with Other Polycrystalline Alumina

    Science.gov (United States)

    Chen, Liang-Yu

    2012-01-01

    A very high purity (99.99+) high temperature co-fired ceramic (HTCC) alumina has recently become commercially available. The raw material of this HTCC alumina is very different from conventional HTCC alumina, and more importantly there is no glass additive in this co-fired material. Previously, selected HTCC and LTCC (low temperature co-fired ceramic) alumina materials were evaluated at high temperatures as dielectric and compared to a regularly sintered 96 polycrystalline alumina (96 Al2O3), where 96 alumina was used as the benchmark. A prototype packaging system based on regular 96 alumina with Au thick-film metallization successfully facilitated long term testing of high temperature silicon carbide (SiC) electronic devices for over 10,000 hours at 500C. In order to evaluate this new HTCC alumina for possible high temperature packaging applications, the dielectric properties of this HTCC alumina substrate were measured and compared with those of 96 alumina and a LTCC alumina from room temperature to 550C at frequencies of 120 Hz, 1 KHz, 10 KHz, 100 KHz, and 1 MHz. A parallel-plate capacitive device with dielectric of the HTCC alumina and precious metal electrodes were used for measurements of the dielectric constant and dielectric loss of the co-fired alumina material in the temperature and frequency ranges. The capacitance and AC parallel conductance of the capacitive device were directly measured by an AC impedance meter, and the dielectric constant and parallel AC conductivity of the dielectric were calculated from the capacitance and conductance measurement results. The temperature and frequency dependent dielectric constant, AC conductivity, and dissipation factor of the HTCC alumina substrate are presented and compared to those of 96 alumina. Other technical advantages of this new co-fired material for possible high packaging applications are also discussed.

  2. Overview of High Purity Magnesium Oxide Application and Production%高纯氧化镁的应用和生产综述

    Institute of Scientific and Technical Information of China (English)

    樊洁

    2012-01-01

    As an important inorganic chemical product,high purity magnesium oxide was widely used in various fields of industry.The application of high purity magnesium oxide was introduced briefly,and the condition of the domestic and foreign high-purity magnesium oxide were compared.From the long-term development,the research and production of high-purity magnesium oxide had broad prospects.%高纯氧化镁作为一种重要的无机化工产品,在工业的各个领域得到了广泛的应用。对高纯氧化镁的应用做了简单的介绍;比较了国内外高纯氧化镁的研究状况。从长远发展看,高纯氧化镁的研究和生产前景广阔。

  3. Mechanical energy losses in plastically deformed and electron plus neutron irradiated high purity single crystalline molybdenum at elevated temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Zelada, Griselda I. [Laboratorio de Materiales, Escuela de Ingenieria Electrica, Facultad de Ciencias Exactas, Ingenieria y Agrimensura, Universidad Nacional de Rosario, Avda. Pellegrini 250, 2000 Rosario (Argentina); Lambri, Osvaldo Agustin [Laboratorio de Materiales, Escuela de Ingenieria Electrica, Facultad de Ciencias Exactas, Ingenieria y Agrimensura, Universidad Nacional de Rosario, Avda. Pellegrini 250, 2000 Rosario (Argentina); Instituto de Fisica Rosario - CONICET, Member of the CONICET& #x27; s Research Staff, Avda. Pellegrini 250, 2000 Rosario (Argentina); Bozzano, Patricia B. [Laboratorio de Microscopia Electronica, Unidad de Actividad Materiales, Centro Atomico Constituyentes, Comision Nacional de Energia Atomica, Avda. Gral. Paz 1499, 1650 San Martin (Argentina); Garcia, Jose Angel [Departamento de Fisica Aplicada II, Facultad de Ciencias y Tecnologia, Universidad del Pais Vasco, Apdo. 644, 48080 Bilbao, Pais Vasco (Spain)

    2012-10-15

    Mechanical spectroscopy (MS) and transmission electron microscopy (TEM) studies have been performed in plastically deformed and electron plus neutron irradiated high purity single crystalline molybdenum, oriented for single slip, in order to study the dislocation dynamics in the temperature range within one third of the melting temperature. A damping peak related to the interaction of dislocation lines with both prismatic loops and tangles of dislocations was found. The peak temperature ranges between 900 and 1050 K, for an oscillating frequency of about 1 Hz. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  4. Gas chromatographic separation of nitrogen, oxygen, argon, and carbon monoxide using custom-made porous polymers from high purity divinylbenzene

    Science.gov (United States)

    Pollock, G. E.; Ohara, D.; Hollis, O. L.

    1984-01-01

    Existing porous polymers were surveyed for their ability to separate the subject gases. Certain products that showed more promise than others were synthesized and the existing synthetic procedures studied and modified to produce new polymers with enhanced ability to separate the subject gases. Evaluation of the porous polymers was carried out practically by gas chromatography at ambient temperature. The modified synthetic procedures were somewhat simpler than the originals. The new porous polymers made with high purity divinylbenzene enabled use of shorter columns to obtain the separations desired.

  5. Magnetic and magnetothermal properties and the magnetic phase diagram of high purity single crystalline terbium along the easy magnetization direction.

    Science.gov (United States)

    Zverev, V I; Tishin, A M; Chernyshov, A S; Mudryk, Ya; Gschneidner, K A; Pecharsky, V K

    2014-02-12

    The magnetic and magnetothermal properties of a high purity terbium single crystal have been re-investigated from 1.5 to 350 K in magnetic fields ranging from 0 to 75 kOe using magnetization, ac magnetic susceptibility and heat capacity measurements. The magnetic phase diagram has been refined by establishing a region of the fan-like phase broader than reported in the past, by locating a tricritical point at 226 K, and by a more accurate definition of the critical fields and temperatures associated with the magnetic phases observed in Tb.

  6. Preparation of uniform nanoparticles of ultra-high purity metal oxides, mixed metal oxides, metals, and metal alloys

    Science.gov (United States)

    Woodfield, Brian F.; Liu, Shengfeng; Boerio-Goates, Juliana; Liu, Qingyuan; Smith, Stacey Janel

    2012-07-03

    In preferred embodiments, metal nanoparticles, mixed-metal (alloy) nanoparticles, metal oxide nanoparticles and mixed-metal oxide nanoparticles are provided. According to embodiments, the nanoparticles may possess narrow size distributions and high purities. In certain preferred embodiments, methods of preparing metal nanoparticles, mixed-metal nanoparticles, metal oxide nanoparticles and mixed-metal nanoparticles are provided. These methods may provide tight control of particle size, size distribution, and oxidation state. Other preferred embodiments relate to a precursor material that may be used to form nanoparticles. In addition, products prepared from such nanoparticles are disclosed.

  7. High-purity Ni electroless plating on screen-printed anodized Al substrates

    Science.gov (United States)

    Park, Sang-Geon; Lee, Youn-Seoung; Rha, Sa-Kyun

    2016-07-01

    By using an electroless plating process with a Ni source solution including dimethylamine borane (DMAB) at pH 6.5 and 65 ◦ C, we obtained a higher purity Ni film (< 1 at.% boron) without damage to the anodized Al substrate. With increasing plating time, the thickness of the film increased gradually, although the average deposition rate of the Ni films decreased steadily. We can infer that the abrupt decrease in sheet resistance (Rs) at the interface region is due to the change in the boron concentration caused by surface reactions, and the gradual decrease in Rs in the bulk region is due mainly to the effect of the saturation of boron's concentration on the thickness. From a boron-distribution viewpoint, this result indicates that the B concentration in the Ni film increases gradually with increasing plating time for plating times ≤ 60 s as a kind of initial stage (that is, interface region), and then saturates uniformly for plating times ≥ 300 s as a kind of bulk region. On the other hand, from an electronic structure viewpoint, this result implies that Ni gains 3d electrons with respect to elemental Ni. The increase in the number of electrons gained by the Ni 3d states may result in an enhancement of the electrical conductivity.

  8. High-purity biodiesel production from microalgae and added-value lipid extraction: a new process.

    Science.gov (United States)

    Veillette, M; Giroir-Fendler, A; Faucheux, N; Heitz, M

    2015-01-01

    A new process was tested in order to produce and purify biodiesel from microalgae lipids and to recover unsaponifiable (added-value) lipids. This process is a two-step biodiesel production including a saponification reaction step followed by an esterification reaction step. The process includes a recovery of the unsaponified lipids between both reaction steps. Among the conditions tested, the following conditions were found to be the best: temperature for both steps (90 °C), saponification time (30 min), esterification time (30 min), sulfuric acid/potassium hydroxide (1.21, w/w), and methanol-lipid ratio (13.3 mL/g). Under these conditions, the fatty acid methyl ester (FAME) yield and the biodiesel purity were, respectively, 32% (g FAME/g lipid) and 77% (g FAME/g biodiesel). This study also showed that the two-step biodiesel process allows a FAME mass composition rich in palmitate (27.9-29.4 wt%), palmitoleate (24.9-26.0 wt%), elaidate (14.8-15.2 wt%), and myristate (12.1-13.0 wt%).

  9. Towards a single step process to create high purity gold structures by electron beam induced deposition at room temperature

    Science.gov (United States)

    Mansilla, C.; Mehendale, S.; Mulders, J. J. L.; Trompenaars, P. H. F.

    2016-10-01

    Highly pure metallic structures can be deposited by electron beam induced deposition and they have many important applications in different fields. The organo-metallic precursor is decomposed and deposited under the electron beam, and typically it is purified with post-irradiation in presence of O2. However, this approach limits the purification to the surface of the deposit. Therefore, ‘in situ’ purification during deposition using simultaneous flows of both O2 and precursor in parallel with two gas injector needles has been tested and verified. To simplify the practical arrangements, a special concentric nozzle has been designed allowing deposition and purification performed together in a single step. With this new device metallic structures with high purity can be obtained more easily, while there is no limit on the height of the structures within a practical time frame. In this work, we summarize the first results obtained for ‘in situ’ Au purification using this concentric nozzle, which is described in more detail, including flow simulations. The operational parameter space is explored in order to optimize the shape as well as the purity of the deposits, which are evaluated through scanning electron microscope and energy dispersive x-ray spectroscopy measurements, respectively. The observed variations are interpreted in relation to other variables, such as the deposition yield. The resistivity of purified lines is also measured, and the influence of additional post treatments as a last purification step is studied.

  10. Study on the High-Purity Gallic Acid%高纯度没食子酸的研究

    Institute of Scientific and Technical Information of China (English)

    张薇; 张强; 马福波; 朱建国

    2000-01-01

    以工业没食子酸为原料,分析了其中所含杂质及存在的形式,提出了分离和纯化过程机理,采用离子交换树脂处理方法,研制出了适合微电子工业使用的高纯度没食子酸。结果表明,样品中所含各种金属离子均≤0.1mg/kg,没食子酸含量≥99.5%。%An analysis is made to fine out the impurities and their existing forms in the industrial gallic acid. According to the principles of separation and purfication,a treatment method of exchanging resin for ion is used to prepare high-purity gallic acid for the microelectronic industrial purposes. The results show that each metal iron in the sample product is less than 0.1 mg/kg and its purity is over 99.5%.

  11. Nearly Blinking-Free, High-Purity Single-Photon Emission by Colloidal InP/ZnSe Quantum Dots.

    Science.gov (United States)

    Chandrasekaran, Vigneshwaran; Tessier, Mickaël D; Dupont, Dorian; Geiregat, Pieter; Hens, Zeger; Brainis, Edouard

    2017-10-11

    Colloidal core/shell InP/ZnSe quantum dots (QDs), recently produced using an improved synthesis method, have a great potential in life-science applications as well as in integrated quantum photonics and quantum information processing as single-photon emitters. Single-particle spectroscopy of 10 nm QDs with 3.2 nm cores reveals strong photon antibunching attributed to fast (70 ps) Auger recombination of multiple excitons. The QDs exhibit very good photostability under strong optical excitation. We demonstrate that the antibunching is preserved when the QDs are excited above the saturation intensity of the fundamental-exciton transition. This result paves the way toward their usage as high-purity on-demand single-photon emitters at room temperature. Unconventionally, despite the strong Auger blockade mechanism, InP/ZnSe QDs also display very little luminescence intermittency ("blinking"), with a simple on/off blinking pattern. The analysis of single-particle luminescence statistics places these InP/ZnSe QDs in the class of nearly blinking-free QDs, with emission stability comparable to state-of-the-art thick-shell and alloyed-interface CdSe/CdS, but with improved single-photon purity.

  12. Application of a Barrier Filter at a High Purity Synthetic Graphite Plant, CRADA 99-F035, Final Report

    Energy Technology Data Exchange (ETDEWEB)

    National Energy Technology Laboratory

    2000-08-31

    Superior Graphite Company and the US Department of Energy have entered into a Cooperative Research and Development Agreement (CRADA) to study the application of ceramic barrier filters at its Hopkinsville, Kentucky graphite plant. Superior Graphite Company is a worldwide leader in the application of advanced thermal processing technology to produce high purity graphite and carbons. The objective of the CRADA is to determine the technical and economic feasibility of incorporating the use of high-temperature filters to improve the performance of the offgas treatment system. A conceptual design was developed incorporating the ceramic filters into the offgas treatment system to be used for the development of a capital cost estimate and economic feasibility assessment of this technology for improving particulate removal. This CRADA is a joint effort of Superior Graphite Company, Parsons Infrastructure and Technology Group, and the National Energy Technology Laboratory (NETL) of the US Department of Energy (DOE).

  13. Industrial-scale separation of high-purity single-chirality single-wall carbon nanotubes for biological imaging.

    Science.gov (United States)

    Yomogida, Yohei; Tanaka, Takeshi; Zhang, Minfang; Yudasaka, Masako; Wei, Xiaojun; Kataura, Hiromichi

    2016-06-28

    Single-chirality, single-wall carbon nanotubes are desired due to their inherent physical properties and performance characteristics. Here, we demonstrate a chromatographic separation method based on a newly discovered chirality-selective affinity between carbon nanotubes and a gel containing a mixture of the surfactants. In this system, two different selectivities are found: chiral-angle selectivity and diameter selectivity. Since the chirality of nanotubes is determined by the chiral angle and diameter, combining these independent selectivities leads to high-resolution single-chirality separation with milligram-scale throughput and high purity. Furthermore, we present efficient vascular imaging of mice using separated single-chirality (9,4) nanotubes. Due to efficient absorption and emission, blood vessels can be recognized even with the use of ∼100-fold lower injected dose than the reported value for pristine nanotubes. Thus, 1 day of separation provides material for up to 15,000 imaging experiments, which is acceptable for industrial use.

  14. Performance of a compact multi-crystal high-purity germanium detector array for measuring coincident gamma-ray emissions

    Energy Technology Data Exchange (ETDEWEB)

    Howard, Chris; Daigle, Stephen; Buckner, Matt [University of North Carolina at Chapel Hill, Chapel Hill, NC 27599 (United States); Triangle Universities Nuclear Laboratory, Durham, NC 27708 (United States); Erikson, Luke E.; Runkle, Robert C. [Pacific Northwest National Laboratory, Richland, WA 99352 (United States); Stave, Sean C., E-mail: Sean.Stave@pnnl.gov [Pacific Northwest National Laboratory, Richland, WA 99352 (United States); Champagne, Arthur E.; Cooper, Andrew; Downen, Lori [University of North Carolina at Chapel Hill, Chapel Hill, NC 27599 (United States); Triangle Universities Nuclear Laboratory, Durham, NC 27708 (United States); Glasgow, Brian D. [Pacific Northwest National Laboratory, Richland, WA 99352 (United States); Kelly, Keegan; Sallaska, Anne [University of North Carolina at Chapel Hill, Chapel Hill, NC 27599 (United States); Triangle Universities Nuclear Laboratory, Durham, NC 27708 (United States)

    2015-05-21

    The Multi-sensor Airborne Radiation Survey (MARS) detector is a 14-crystal array of high-purity germanium (HPGe) detectors housed in a single cryostat. The array was used to measure the astrophysical S-factor for the {sup 14}N(p,γ){sup 15}O{sup ⁎} reaction for several transition energies at an effective center-of-mass energy of 163 keV. Owing to the granular nature of the MARS detector, the effect of gamma-ray summing was greatly reduced in comparison to past experiments which utilized large, single-crystal detectors. The new S-factor values agree within their uncertainties with the past measurements. Details of the analysis and detector performance are presented.

  15. Performance of A Compact Multi-crystal High-purity Germanium Detector Array for Measuring Coincident Gamma-ray Emissions

    Energy Technology Data Exchange (ETDEWEB)

    Howard, Chris [Univ. of North Carolina, Chapel Hill, NC (United States); Triangle Univ. Nuclear Lab., Durham, NC (United States); Daigle, Stephen [Univ. of North Carolina, Chapel Hill, NC (United States); Triangle Univ. Nuclear Lab., Durham, NC (United States); Buckner, Matt [Univ. of North Carolina, Chapel Hill, NC (United States); Triangle Univ. Nuclear Lab., Durham, NC (United States); Erikson, Luke E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Runkle, Robert C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Stave, Sean C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Champagne, Art [Univ. of North Carolina, Chapel Hill, NC (United States); Triangle Univ. Nuclear Lab., Durham, NC (United States); Cooper, Andrew [Univ. of North Carolina, Chapel Hill, NC (United States); Triangle Univ. Nuclear Lab., Durham, NC (United States); Downen, Lori [Univ. of North Carolina, Chapel Hill, NC (United States); Triangle Univ. Nuclear Lab., Durham, NC (United States); Glasgow, Brian D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Kelly, Keegan [Univ. of North Carolina, Chapel Hill, NC (United States); Triangle Univ. Nuclear Lab., Durham, NC (United States); Sallaska, Anne [Univ. of North Carolina, Chapel Hill, NC (United States); Triangle Univ. Nuclear Lab., Durham, NC (United States)

    2015-02-18

    The Multi-sensor Airborne Radiation Survey (MARS) detector is a 14-crystal array of high-purity germanium (HPGe) detectors housed in a single cryostat. The array was used to measure the astrophysical S-factor for the 14N(p,γ)15O* reaction for several transition energies at an effective center of mass energy of 163 keV. Owing to the segmented nature of the MARS detector, the effect of gamma-ray summing was greatly reduced in comparison to past experiments which utilized large, single-crystal detectors. The new S-factor values agree within the uncertainties with the past measurements. Details of the analysis and detector performance will be presented.

  16. Phase transformations of high-purity PbI{sub 2} nanoparticles synthesized from lead-acid accumulator anodes

    Energy Technology Data Exchange (ETDEWEB)

    Malevu, T.D., E-mail: malevutd@ufs.ac.za; Ocaya, R.O.; Tshabalala, K.G.

    2016-09-01

    High-purity hexagonal lead iodide nanoparticles have been synthesized from a depleted sealed lead acid battery anode. The synthesized product was found to consist of the rare 6R polytype form of PbI{sub 2} that is thought to have good potential in photovoltaic applications. We investigate the effects of annealing time and post-melting temperature on the structure and optical properties using 1.5418 Å CuKα radiation. Photoluminescence measurements were done under 150 W/221 nm wavelength xenon excitation. Phase transformation was observed through XRD peaks when annealing time increased from 0.5–5 h. The nanoparticle grain size and inter-planar distance appeared to be independent of annealing time. PL measurements show three broad peaks in a range of 400 nm to 700 nm that are attributed to excitonic, donor–acceptor pair and luminescence bands from the deep levels.

  17. Growth and structural characterization of pyramidal site-controlled quantum dots with high uniformity and spectral purity

    CERN Document Server

    Dimastrodonato, Valeria; Young, Robert J; Pelucchi, Emanuele

    2010-01-01

    This work presents some fundamental features of pyramidal site-controlled InGaAs Quantum Dots (QDs) grown by MetalOrganic Vapour Phase Epitaxy on patterned GaAs (111)B substrate. The dots self-form inside pyramidal recesses patterned on the wafer via pre-growth processing. The major advantage of this growth technique is the control it provides over the dot nucleation posi-tion and the dimensions of the confined structures onto the sub-strate. The fundamental steps of substrate patterning and the QD forma-tion mechanism are described together with a discussion of the structural particulars. The post-growth processes, including sur-face etching and substrate removal, which are required to facili-tate optical characterization, are discussed. With this approach extremely high uniformity and record spectral purity are both achieved.

  18. Formation and annihilation of intrinsic defects induced by electronic excitation in high-purity crystalline SiO{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Kajihara, Koichi [Department of Applied Chemistry, Graduate School of Urban Environmental Sciences, Tokyo Metropolitan University, 1-1 Minami-Osawa, Hachioji 192-0397 (Japan); Skuja, Linards [Institute of Solid State Physics, University of Latvia, Kengaraga iela 8, LV1063 Riga (Latvia); Hosono, Hideo [Materials and Structures Laboratory and Frontier Research Center, Tokyo Institute of Technology, 4259 Nagatsuta, Midori-ku, Yokohama 226-8503 (Japan)

    2013-04-14

    Formation and thermal annihilation of intrinsic defects in {alpha}-quartz were examined using high-purity samples, while minimizing the contributions of reactions involving metallic impurities. Electronic excitation with {sup 60}Co {gamma}-rays was employed to avoid radiation-induced amorphization. The results clearly show that formation of oxygen vacancies (Si-Si bonds) as a result of decomposition of regular Si-O-Si bonds (Frenkel process) is the dominant intrinsic defect process. Compared with amorphous SiO{sub 2}, in {alpha}-quartz, the formation yield of Si-Si bonds is an order of magnitude smaller, the 7.6 eV optical absorption band is less broadened, and their thermal annihilation is complete at a lower temperature, around the {alpha}-{beta} quartz transition. In contrast, radiation-induced interstitial oxygen atoms practically do not form interstitial oxygen molecules.

  19. Gamma-ray observations of SN 1987A with an array of high-purity germanium detectors

    Science.gov (United States)

    Sandie, W. G.; Nakano, G. H.; Chase, L. F., Jr.; Fishman, G. J.; Meegan, C. A.; Wilson, R. B.; Paciesas, W.

    A balloonborne gamma-ray spectrometer comprising an array of high-purity n-type germanium detectors was flown from Alice Springs, Northern Territory, Australia, on May 29 - 30, 1987, 96 days after the observed neutrino pulse. SN 1987A was within the 22-deg field of view for about 3300 s during May 29.9 - 30.3 UT. No excess gamma rays were observed at energies appropriate to the Ni(56) - Co(56) decay chain or from other lines in the energy region from 0.1 to 3.0 MeV. The data imply that there was less than 2.5×10-4 solar masses of Co(56) exposed to the Earth at the time of the observation. Additional balloon-borne observations are planned.

  20. Recycling of AZ31 Mg alloy with high purity Mg deposition layer by hot working (solid recycling)

    Energy Technology Data Exchange (ETDEWEB)

    Chino, Y.; Mabuchi, M. [Inst. for Structural and Engineering Materials, National Inst. of Advanced Industrial Science and Technology, Nagoya (Japan); Yamamoto, A.; Iwasaki, H.; Tsubakino, H. [Div. of Materials Science and Engineering, Graduate School of Himeji Inst. of Tech., Himeji (Japan)

    2003-07-01

    Solid recycling of AZ31 Mg alloy with vapor deposition coating layer of high purity Mg was evaluated. In the open die forging experiments, two AZ31 Mg alloy specimens with the pure Mg layer were sufficiently bonded by forging at 673 K. Furthermore, the Al and Zn of the AZ31 substrate diffused up to the center of the pure Mg layer. By the theoretical analysis, it is suggested that the grain boundary diffusion enhanced by grain refinement due to hot forging contributes to the solid state bonding of the specimens. Also, the solid recycled specimen was fabricated from the AZ31 Mg substrate with pure Mg layer by hot extrusion at 673 K. The solid recycled specimen showed almost the same tensile properties as the virgin extruded specimen. This is probably related not only to the grain boundary diffusion but also severe plastic deformation by hot extrusion. (orig.)

  1. 高纯镓制备技术的研究进展%Study Status of Preparing Method for High-purity Gallium

    Institute of Scientific and Technical Information of China (English)

    厉英; 曾杰; 闫晨; 刘杰

    2013-01-01

    High-purity gallium is mainly used in wireless communication and photoelectric semiconductor field in the form of GaAs, GaP and GaN. With the rapid development of the market on 3G smartphone and LED, the de mand for high-purity gallium increases steadily, so it is essential to enhance the research and production of high-purity gallium. The related methods for preparing high-purity gallium are reviewed, the advantages and disadvantages of the various methods are compared. It is pointed out that the combined process is an efficient and feasible method to produ cing high-purity gallium.%高纯镓主要以砷化镓、磷化镓、氮化镓的形式应用于无线通讯和光电半导体领域;随着3G智能手机、LED市场的快速发展,对高纯镓产品需求越来越大,因此应加强对高纯镓的研制和生产.总结了高纯镓的相关制备方法,分析比较了各种方法的优缺点,指出联合法是生产高纯镓的高效可行的方法.

  2. High-purity 60GHz band millimeter-wave generation based on optically injected semiconductor laser under subharmonic microwave modulation.

    Science.gov (United States)

    Fan, Li; Xia, Guangqiong; Chen, Jianjun; Tang, Xi; Liang, Qing; Wu, Zhengmao

    2016-08-08

    Based on an optically injected semiconductor laser (OISL) operating at period-one (P1) nonlinear dynamical state, high-purity millimeter-wave generation at 60 GHz band is experimentally demonstrated via 1/4 and 1/9 subharmonic microwave modulation (the order of subharmonic is with respect to the frequency fc of the acquired 60 GHz band millimeter-wave but not the fundamental frequency f0 of P1 oscillation). Optical injection is firstly used to drive a semiconductor laser into P1 state. For the OISL operates at P1 state with a fundamental frequency f0 = 49.43 GHz, by introducing 1/4 subharmonic modulation with a modulation frequency of fm = 15.32 GHz, a 60 GHz band millimeter-wave with central frequency fc = 61.28 GHz ( = 4fm) is experimentally generated, whose linewidth is below 1.6 kHz and SSB phase noise at offset frequency 10 kHz is about -96 dBc/Hz. For fm is varied between 13.58 GHz and 16.49 GHz, fc can be tuned from 54.32 GHz to 65.96 GHz under matched modulation power Pm. Moreover, for the OISL operates at P1 state with f0 = 45.02 GHz, a higher order subharmonic modulation (1/9) is introduced into the OISL for obtaining high-purity 60 GHz band microwave signal. With (fm, Pm) = (7.23 GHz, 13.00 dBm), a microwave signal at 65.07 GHz ( = 9fm) with a linewidth below 1.6 kHz and a SSB phase noise less than -98 dBc/Hz is experimentally generated. Also, the central frequency fc can be tuned in a certain range through adjusting fm and selecting matched Pm.

  3. Properties of high k gate dielectric gadolinium oxide deposited on Si (1 0 0) by dual ion beam deposition (DIBD)

    Science.gov (United States)

    Zhou, Jian-Ping; Chai, Chun-Lin; Yang, Shao-Yan; Liu, Zhi-Kai; Song, Shu-Lin; Li, Yan-Li; Chen, Nuo-Fu

    2004-09-01

    Gadolinium oxide thin films have been prepared on silicon (1 0 0) substrates with a low-energy dual ion-beam epitaxial technique. Substrate temperature was an important factor to affect the crystal structures and textures in an ion energy range of 100-500 eV. The films had a monoclinic Gd2O3 structure with preferred orientation (4 bar 0 2) at low substrate temperatures. When the substrate temperature was increased, the orientation turned to (2 0 2), and finally, the cubic structure appeared at the substrate temperature of 700 °C, which disagreed with the previous report because of the ion energy. The AES studies found that Gadolinium oxide shared Gd2O3 structures, although there were a lot of oxygen deficiencies in the films, and the XPS results confirmed this. AFM was also used to investigate the surface images of the samples. Finally, the electrical properties were presented.

  4. Gadolinium photoionization process

    Science.gov (United States)

    Paisner, J.A.; Comaskey, B.J.; Haynam, C.A.; Eggert, J.H.

    1993-04-13

    A method is provided for selective photoionization of the odd-numbered atomic mass gadolinium isotopes 155 and 157. The selective photoionization is accomplished by circular or linear parallel polarized laser beam energy effecting a three-step photoionization pathway.

  5. 高纯六氟化钨制备工艺研究%Preparation Technology of High Purity Tungsten Hexafluoride

    Institute of Scientific and Technical Information of China (English)

    陈志刚; 陈财华; 冯振雷

    2014-01-01

    介绍了利用氟气与钨粉为原料制备高纯六氟化钨的工艺方法和设备体系。其过程是利用电解槽电解氟氢化钾制取氟气,并采用氟化钠吸附配合深冷工艺纯化氟气,净化后的氟气与固定床里的钨粉在一定温度条件下反应合成初级六氟化钨,通过低温冷凝回收,收集的初级六氟化钨经过固化后抽真空排轻等方法进行初步提纯,然后将初步提纯的产品蒸馏至填料式精馏塔内进行深度提纯,经过多步提纯后的成品六氟化钨纯度可达99.999%以上。%This paper introduces the processing and equipment system for high-purity tungsten hexafluoride using fluorine gas and tungsten powder as raw materials. Electrolytic cell is applied to prepare fluorine gas by electrolyzing the potassium bifluoride. Sodium fluoride adsorption with cryogenic mixture is used to purify the fluorine gas. Purified fluorine gas reacts with tungsten powder to synthesize the impure tungsten hexafluoride in the fixed bed reactor at a certain temperature. The impure tungsten hexafluoride is obtained by low-temperature condensation. Curing and vacuuming technologies are performed on impure tungsten hexafluoride use to remove the volatile impurity. Filler type distillation column is utilized to further purify by monitoring the distillation products intermittently to prevent unqualified products collection. The results show that the purity of tungsten hexafluoride reaches 99.999%.

  6. Recombinant high-density lipoprotein nanoparticles containing gadolinium-labeled cholesterol for morphologic and functional magnetic resonance imaging of the liver

    Directory of Open Access Journals (Sweden)

    Rui M

    2012-07-01

    Full Text Available Mengjie Rui,1 Wei Guo,2 Qian Ding,2 Xiaohui Wei,2 Jianrong Xu,3 Yuhong Xu21School of Life Science and Biotechnology, 2School of Pharmacy, Shanghai Jiao Tong University, Shanghai, People's Republic of China; 3Department of Radiology, Renji Hospital Affiliation with Medical School of Shanghai Jiao Tong University, Shanghai, People's Republic of ChinaBackground: Natural high-density lipoproteins (HDL possess important physiological functions to the transport of cholesterol from the peripheral tissues to the liver for metabolic degradation and excretion in the bile.Methods and results: In this work, we took advantage of this pathway and prepared two different gadolinium (Gd-DTPA-labeled cholesterol-containing recombinant HDL nanoparticles (Gd-chol-HDL and Gd-(chol2-HDL as liver-specific magnetic resonance imaging (MRI contrast agents. The reconstituted HDL nanoparticles had structural similarity to native HDL, and could be taken up by HepG2 cells via interaction with HDL receptors in vitro. In vivo MRI studies in rats after intravenous injections of 10 µmol gadolinium per kg of recombinant HDL nanoparticles indicated that both nanoparticles could provide signal enhancement in the liver and related organs. However, different T1-weighted image details suggested that they participated in different cholesterol metabolism and excretion pathways in the liver.Conclusion: Such information could be highly useful to differentiate functional changes as well as anatomic differences in the liver. These cholesterol-derived contrast agents and their recombinant HDL preparations may warrant further development as a new class of contrast agents for MRI of the liver and related organs.Keywords: magnetic resonance imaging, apolipoprotein, high-density lipoprotein, contrast agent, gadolinium, liver

  7. Impurity and Defect Behavior in High-Purity Epitaxial GaAs.

    Science.gov (United States)

    1979-09-26

    Japanese Journal of Applied Physics 9, 156 (1970). -113- 11. T...Saito and F. Hasegawa, "Cause of the High Resis- tance Region at Vapour Epitaxial GaAs Layer-Sub- strate Interface", Japanese Journal of Applied Physics 10...Ryuzan, "Electrical Prop- erties of n-Type Gallium Arsenide at High Tempera- tures", Japanese Journal of Applied Physics 10, 392 (1971). 35. P.

  8. Thermal behavior of Ni (99.967% and 99.5% purity) deformed to an ultra-high strain by high pressure torsion

    DEFF Research Database (Denmark)

    Zhang, H.W.; Huang, Xiaoxu; Pippan, R.

    2010-01-01

    Polycrystalline Ni of two purities (99.967% (4N) and 99.5% (2N)) was deformed to an ultra-high strain of εvM = 100 (εvM, von Mises strain) by high pressure torsion at room temperature. The 4N and 2N samples at this strain are nanostructured with an average boundary spacing of 100 nm, a high density...... Ni, respectively. The isochronal annealing leads to a drop in hardness in three stages: a relatively small decrease at low temperatures (recovery), followed by a rapid decrease at intermediate temperatures (recrystallization) and a slow decrease at high temperature (grain growth). Both recovery...

  9. High-frequency drug purity and price series as tools for explaining drug trends and harms in Victoria, Australia.

    Science.gov (United States)

    Scott, Nick; Caulkins, Jonathan P; Ritter, Alison; Quinn, Catherine; Dietze, Paul

    2015-01-01

    Methamphetamine-related harms in Victoria have increased recently in the context of stable or declining use prevalence. We determine how changes in price and purity of methamphetamine compared to other drugs such as heroin may, in part, explain these divergent patterns. Detailed methamphetamine and heroin purchase price data from 2152 participant interviews from the Melbourne Injecting Drug User cohort study were used to generate drug price series for the period January 2009-June 2013. Data on drug purity from 8818 seizures made within Victoria were used to generate drug purity series during the same period. Purity-adjusted price data for methamphetamine and heroin were obtained for the period 2009-13 by combining the two data sets. While the average purity of heroin seizures remained consistent and low, the average purity of powder and of crystal methamphetamine seizures increased from 12% [95% confidence interval (CI) = 10-14%] to 37% (95% CI = 20-54%) and 21% (95% CI = 18-23%) to 64% (95% CI = 60-68%), respectively. Crystal methamphetamine purity was bimodal, with observations generally less than 20% or greater than 70%. The average unadjusted price per gram for heroin decreased from $374 (95% CI = $367-381) to $294 (95% CI = $280-308), powder methamphetamine did not change significantly from $252 (95% CI = $233-271), and crystal methamphetamine increased substantially from $464 (95% CI = $416-511) in 2009 to $795 (95% CI = $737-853) in 2011. This increase was offset by an even greater increase in purity, meaning the average purity-adjusted price per gram declined. Furthermore, pure prices of both methamphetamine forms were similar, whereas their unadjusted prices were not. The pure price of heroin fluctuated with no ongoing trends. Decreases in methamphetamine purity-adjusted price along with the bimodality of crystal methamphetamine purity may account for some of the recent increase in methamphetamine-related harm. For a

  10. High-purity rare-earth metals: preparation, properties, and application

    Institute of Scientific and Technical Information of China (English)

    Kol'chugina; N.; B.; Burkhanov; G.; S.; Chistyakov; O.; D.; Burkhanov; Yu.; S.

    2005-01-01

    In recent years, the ever-growing interest of investigators to the study of rare-earth metals REM) is observed owing to unique properties of the metals and potential uses in electronics, laser technology, space technology, medicine, and many other high-technology applications.……

  11. High-purity rare-earth metals: preparation, properties, and application

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    @@ In recent years, the ever-growing interest of investigators to the study of rare-earth metals REM) is observed owing to unique properties of the metals and potential uses in electronics, laser technology, space technology, medicine, and many other high-technology applications.

  12. Quantification of the microstructures of high purity nickel subjected to dynamic plastic deformation

    DEFF Research Database (Denmark)

    Luo, Z.P.; Zhang, H.W.; Hansen, Niels

    2012-01-01

    and the misorientation angle across dislocation boundaries and high angle boundaries. These boundaries subdivide the structure on a finer and finer scale towards saturation at the highest strain. The structural evolution follows a hierarchical pattern from the formation of cells and cell blocks to a characteristic...

  13. High-Purity Hybrid Organolead Halide Perovskite Nanoparticles Obtained by Pulsed-Laser Irradiation in Liquid

    KAUST Repository

    Amendola, Vincenzo

    2016-11-17

    Nanoparticles of hybrid organic-inorganic perovskites have attracted a great deal of attention due to their variety of optoelectronic properties, their low cost, and their easier integration into devices with complex geometry, compared with microcrystalline, thin-film, or bulk metal halides. Here we present a novel one-step synthesis of organolead bromide perovskite nanocrystals based on pulsed-laser irradiation in a liquid environment (PLIL). Starting from a bulk CHNHPbBr crystal, our PLIL procedure does not involve the use of high-boiling-point polar solvents or templating agents, and runs at room temperature. The resulting nanoparticles are characterized by high crystallinity and are completely free of any microscopic product or organic coating layer. We also demonstrate the straightforward inclusion of laser-generated perovskite nanocrystals in a polymeric matrix to form a nanocomposite with single- and two-photon luminescence properties.

  14. State-of-the-art in analytical characterization of high purity solid samples by different spectroscopic methods

    Indian Academy of Sciences (India)

    S S Grazhulene

    2005-07-01

    Facilities and some results of several spectroscopic methods which have potential applications in the field of analysis of solid high purity substances and which have been elaborated in Russia, will be discussed in this paper. Laser nondispersive atomic fluorescence method with glow discharge cathode sputtering atomiser, may be used for trace element determination as well as a tool for the investigation of technological processes, viz. deposition of thin films. Investigations on reduction of a background level in the new hollow cathode ion source for mass-spectrometry have been carried out. Laser mass spectrometry with tandem laser mass reflectron is successfully designed and applied for gaseous impurities determination in high pure silicon with limit of detection of 10-3–10-5 ppm wt. Several results of the layer-by-layer and bulk trace analysis of solids by high resolution mass spectrometry with radio frequency powered glow discharge ion source with the limits of detection at 10-1–10-3 ppm wt will be presented here. The traditional arc and spark emission technique still finds considerable use. One of the examples considered in the paper is the analysis of metalfullerenes. To overcome the calibration problem the fluorination process inside the electrode crater using zinc fluoride has been investigated.

  15. The control of purity and stoichiometry of compound semiconductors by high vapor pressure transport

    Science.gov (United States)

    Bachmann, Klaus J.; Ito, Kazufumi; Scroggs, Jeffery S.; Tran, Hien T.

    1995-01-01

    In this report we summarize the results of a three year research program on high pressure vapor transport (HPVT) of compound semiconductors. Most of our work focused onto pnictides, in particular ZnGeP2, as a model system. Access to single crystals of well controlled composition of this material is desired for advancing the understanding and control of its point defect chemistry in the contest of remote, real-time sensing of trace impurities, e.g., greenhouse gases, in the atmosphere by ZnGeP2 optical parametric oscillators (OPO's).

  16. Cryogenic Implosion Performance Using High-Purity Deuterium-Tritium Fuel

    Science.gov (United States)

    Sangster, T. C.; Goncharov, V. N.; Radha, P. B.; Earley, R.; Epstein, R.; Forrest, C. J.; Froula, D. H.; Glebov, V. Yu.; Hu, S. X.; Igumenshchev, I. V.; Marshall, F. J.; McKenty, P. W.; Shmayda, W. T.; Shoup, M. J., III; Michel, D. T.; Stoeckl, C.; Seka, W.; Frenje, J. A.; Gatu Johnson, M.

    2014-10-01

    Demonstrating hydrodynamic equivalence between symmetric implosions on OMEGA and National Ignition Facility ignition designs will require a number of facility enhancements that include dynamic bandwidth reduction, a set of higher-order super-Gaussian phase plates, high-spatial-resolution gated-core imaging, high-bandwidth neutron burnwidth measurements, improved power balance, and contaminant-free deuterium-tritium (DT) fuel. The historic DT fuel supply was contaminated with ~6 atm% of 1H, leading to significant fractionation of the fuel during the layering process (the triple points of H:D and H:T are significantly colder than DD, DT, and TT). The fractionation leads to a drop in the potential yield because the D and T number densities are lower in the void than they would be with a pure-DT mixture). An isotope separation system has been developed to remove the 1H from the DT fuel supply. This talk will discuss the first results with the purified fuel, conclusions from recent implosions to test cross-beam energy transfer mitigation, and the status of the remaining facility enhancements. This material is based upon work supported by the Department of Energy National Nuclear Security Administration under Award Number DE-NA0001944.

  17. thesis of high-purity carbon nanotubes over alumina and silica supported bimetallic catalysts

    Directory of Open Access Journals (Sweden)

    Sanja Ratković

    2009-10-01

    Full Text Available Carbon nanotubes (CNTs were synthesized by a catalytic chemical vapor deposition method (CCVD of ethylene over alumina and silica supported bimetallic catalysts based on Fe, Co and Ni. The catalysts were prepared by a precipitation method, calcined at 600 °C and in situ reduced in hydrogen flow at 700 °C. The CNTs growth was carried out by a flow the mixture of C2H4 and nitrogen over the catalyst powder in a horizontal oven. The structure and morphology of as-synthesized CNTs were characterized using SEM. The as-synthesized nanotubes were purified by acid and basic treatments in order to remove impurities such as amorphous carbon, graphite nanoparticles and metal catalysts. XRD and DTA/TG analyses showed that the amounts of by-products in the purified CNTs samples were reduced significantly. According to the observed results, ethylene is an active carbon source for growing high-density CNTs with high yield but more on alumina-supported catalysts than on their silica- supported counterparts. The last might be explained by SMSI formed in the case of alumina-supported catalysts, resulting in higher active phase dispersion.

  18. High Purity Germanium Gamma-PHA Assay of Uranium Scrap Cans Used in 321-M Facility

    Science.gov (United States)

    Salaymeh, S. R.; Dewberry, R. A.; Casella, V.

    2001-12-01

    The Analytical Development Section of SRTC was requested by the Facilities Disposition Division (FDD) to determine the holdup of enriched uranium in the 321-M facility as part of an overall deactivation project of the facility. The 321-M facility was used to fabricate enriched uranium fuel assemblies, lithium-aluminum target tubes, neptunium assemblies, and miscellaneous components for the production reactors. The facility also includes the 324-M storage building and the passageway connecting it to 321-M. The results of the holdup assays are essential for determining compliance with the Solid Waste's Waste Acceptance Criteria, Material Control & Accountability, and to meet criticality safety controls. This report describes and documents the use of a portable HPGe detector and EG&G DART system that contains a high voltage power supply, signal processing electronics, a personal computer with Gamma-Vision software, and space to store and manipulate multiple 4096-channel gamma-ray spectra to assay for 235U content. The system was used to assay a large number of scrap cans used to store highly enriched uranium (HEU) chips and filings. This report includes a description of two efficiency calibration configurations and also the results of the assay. A description of the quality control checks is included as well.

  19. A process for high yield and scaleable recovery of high purity eicosapentaenoic acid esters from microalgae and fish oil.

    Science.gov (United States)

    Belarbi; Molina; Chisti

    2000-04-01

    A low expense process is developed for recovering esterified eicosapentaenoic acid (EPA) from microalgae and fish oil. Over 70% of the EPA content in the esterified crude extract of microalgae were recovered at purities exceeding 90%. The recovery scheme utilizes either wet or freeze-dried algal biomass. The process consists of only three main steps: 1) simultaneous extraction and transesterification of the algal biomass; 2) argentated silica gel column chromatography of the crude extract; and 3) removal of pigments by a second column chromatographic step. Argentated silica gel chromatography recovered about 70% of the EPA ester present in the crude fatty ester mixture of fish oil, but at a reduced purity ( approximately 83% pure) compared to the microalgal derived EPA. The optimal loading of the fatty ester mixture on the chromatographic support was about 3% (w/w) but loadings up to 4% did not affect the resolution significantly. The process was scaled up by a factor of nearly 320 by increasing the diameter of the chromatography columns. The elution velocity remained constant. Compared to the green alga Monodus subterraneus, the diatom Phaeodactylum tricornutum had important advantages as a potential commercial producer of EPA. For a microalgal EPA process to be competitive with fish oil derived EPA, P. tricornutum biomass (2.5% w/w EPA) needs to be obtained at less than $4/kg. If the EPA content in the alga are increased to 3.5%, the biomass may command a somewhat higher price. The quality of microalgal EPA compares favorably with that of the fish oil product. Compared to free fatty acid, EPA ester is more stable in storage. Shelf-life is extended by storing in hexane. The silver contamination in the final purified EPA was negligibly small (<210 ppb).

  20. A simplified method for obtaining high-purity perchlorate from groundwater for isotope analyses.

    Energy Technology Data Exchange (ETDEWEB)

    vonKiparski, G; Hillegonds, D

    2011-04-04

    Investigations into the occurrence and origin of perchlorate (ClO{sub 4}{sup -}) found in groundwater from across North America have been sparse until recent years, and there is mounting evidence that natural formation mechanisms are important. New opportunities for identifying groundwater perchlorate and its origin have arisen with the utilization of improved detection methods and sampling techniques. Additionally, application of the forensic potential of isotopic measurements has begun to elucidate sources, potential formation mechanisms and natural attenuation processes. Procedures developed appear to be amenable to enable high precision stable isotopic analyses, as well as lower precision AMS analyses of {sup 36}Cl. Immediate work is in analyzing perchlorate isotope standards and developing full analytical accuracy and uncertainty expectations. Field samples have also been collected, and will be analyzed when final qa/qc samples are deemed acceptable.

  1. 18F half-life measurement using a high-purity germanium detector.

    Science.gov (United States)

    Han, Jubong; Lee, K B; Park, T S; Lee, J M; Oh, P J; Lee, S H; Kang, Y S; Ahn, J K

    2012-11-01

    The half-life of (18)F has been measured using HPGe detectors with a (137)Cs reference source. The counting ratio of 511 keV γ-rays from (18)F to 622 keV γ-rays from (137)Cs was fitted for the half-life with a weighted least-square method. Uncertainties due to the systematic effects arising from the measurement of a high activity (18)F source were studied in detail. The half-life of (18)F was found to be (109.72±0.19) min. The result is in a good agreement with the recommended value of (109.728±0.019) min evaluated at the Laborotaire National Henri Becquerel (LNHB).

  2. A method for high purity sorting of rare cell subsets applied to TDC.

    Science.gov (United States)

    Kuka, Mirela; Ashwell, Jonathan D

    2013-12-31

    T(DC) are a recently described subset of polyclonal αβ T-cells with dendritic cell properties. Because of their low number in peripheral immune compartments, isolation and characterization of T(DC) with existing purification methods are technically challenging. Here we describe a customized gating strategy and a flow cytometry-based cell sorting protocol for isolation of T(DC). The protocol was developed because, despite very conservative gating for dead-cell and doublet exclusion, cells obtained with normal sorting procedures were enriched for T(DC) but not pure. Re-sorting the output of the first round of sorting results in highly pure T(DC). Cells obtained with this method are viable and can be used for in vitro characterization. Moreover, this double-round sorting strategy can be universally applied to the isolation of other rare cell subsets.

  3. Muon diffusion and trapping studies in high purity vanadium. [Temperature dependence

    Energy Technology Data Exchange (ETDEWEB)

    Heffner, R.H.; Brown, J.A.; Hutson, R.L.; Leon, M.; Gauster, W.B.; Carlson, O.N.; Rehbein, D.K.; Fiory, A.T.

    1978-01-01

    The first results of a study of the effects of varying impurity concentration on the temperature dependence of the depolarization rate of positive muons implanted into vanadium are presented. Data are reported for the most highly purified polycrystalline sample yet measured, and the same sample subsequently doped with about 500 ppM oxygen by weight. The data for the pure sample shows a low depolarization rate (< .15 ..mu..sec/sup -1/) at all temperatures measured, showing a broad minimum centered at approx. 35 K, followed by a sharp peak near 90 K and a rapid drop to negligible values at 200 K. The data are contrasted with previously published data on less pure samples, and call into question previous interpretations of the behavior of the ..mu../sup +/ at low temperatures in impure vanadium as one-phonon-assisted tunneling. 6 references.

  4. Growth of high purity N-polar (In,Ga)N films

    Science.gov (United States)

    Lund, Cory; Nakamura, Shuji; DenBaars, Steven P.; Mishra, Umesh K.; Keller, Stacia

    2017-04-01

    In this work, secondary ion mass spectroscopy was used to study carbon and oxygen impurity incorporation in N-polar [000-1] GaN films grown by MOCVD. The effects of growth temperature, V/III ratio, and precursor flows were studied within a regime relevant to low temperature (In,Ga)N:Mg growth for device structures containing high indium concentrations. For films grown without magnesium, oxygen levels were between 3 and 8×1016 cm-3 and did not depend strongly on the growth conditions. Mg-doped films yielded higher oxygen concentrations ranging from 8×1016 to 4×1017 cm-3 depending on the gallium and magnesium precursor flow rates. The carbon concentration in the films varied significantly with different growth conditions, and was most affected by the growth temperature and the V/III ratio. With careful tuning of the growth parameters carbon and oxygen concentrations of 2 and 4×1016 cm-3, respectively, were achievable under a wide range of conditions.

  5. Direct solid sampling electrothermal atomic absorption spectrometry for the analysis of high-purity niobium pentaoxide.

    Science.gov (United States)

    Huang, M D; Krivan, V

    2000-01-01

    A direct solid sampling electrothermal atomic absorption spectrometry (SoS-ETAAS) method for ultratrace analysis of powdered niobium pentaoxide for Al, Co, Cr, Cu, Fe, K, Mg, Mn, Na, Ni and Zn has been developed. The elements K, Mg, Na and Zn could be determined without any chemical modification. However, in the determination of the elements Al, Co, Cr, Cu, Fe, Mn and Ni, serious matrix-caused non-spectral interferences and background occurred which made their determination impossible. This problem was remedied by conversion of the niobium pentaoxide matrix into the thermally stable niobium carbide by using methane atmosphere during the pyrolysis stage. The development resulted in establishing an extraordinary powerful method for the analysis of niobium pentaoxide in term of limits of detection, accuracy, simplicity and analysis time. Quantification was performed using calibration curves measured with aqueous standard solutions. The accuracy was checked by comparing the results with those obtained by ETAAS in analysis of slurries and digests of the sample. Due to almost complete freedom of blank and high applicable sample amounts (up to 15 mg), extremely low limits of detection (0.5-2 ng/g) were achieved.

  6. Expression and purification of bioactive high-purity human midkine in Escherichia coli

    Institute of Scientific and Technical Information of China (English)

    Zhong-hui ZHANG; Li-juan DU; Di XIANG; Shun-ying ZHU; Ming-yuan WU; Hui-li LU; Yan YU; Wei HAN

    2009-01-01

    Midkine is a heparin-binding growth factor,which plays important roles in the regulation of cell growth and differentiation.The non-tagged recombinant human midkine (rhMK) is therefore required to facilitate its functional studies of this important growth factor.In the present work,rhMK was expressed in Escherichia coli (E.coli) BL21 (DE3).The expression of midkine was efficiently induced by isopropyl-β-D-thiogalactopyranoside (IPTG).After sonication,midkine was recovered in an insoluble form,and was dissolved in guaoidine hydrochloride buffer.Renaturation of the denatured protein was carried out in the defined protein refolding buffer,and the refolded protein was purified using S-Sepharose ion-exchange chromatography.The final preparation of the rhMK was greater than 98% pure as measured by sodium dodecylsulfate-polyacrylamid gel electrophoresis (SDS-PAGE) and reverse phase high performance liquid chromatography (RP-HPLC).The purified rhMK enhanced the proliferation of NIH3T3 cells.

  7. Exceptional Oxygen Sensing Properties of New Blue Light-Excitable Highly Luminescent Europium(III) and Gadolinium(III) Complexes

    OpenAIRE

    Borisov, Sergey M.; Fischer, Roland; Saf, Robert; Klimant, Ingo

    2014-01-01

    New europium(III) and gadolinium(III) complexes bearing 8-hydroxyphenalenone antenna combine efficient absorption in the blue part of the spectrum and strong emission in polymers at room temperature. The Eu(III) complexes show characteristic red luminescence whereas the Gd(III) dyes are strongly phosphorescent. The luminescence quantum yields are about 20% for the Eu(III) complexes and 50% for the Gd(III) dyes. In contrast to most state-of-the-art Eu(III) complexes the new dyes are quenched v...

  8. SYNTHESIS OF HIGH PURITY TiO2 NANOPARTICLES FROM Ti(SO4)2 IN PRESENCE OF EDTA AS COMPLEXING AGENT

    Institute of Scientific and Technical Information of China (English)

    Yu Li; Yu Guo; Youzhi Liu

    2005-01-01

    TiO2 nanoparticles were synthesized by a homogeneous controlled precipitation method using industrial titanium sulfate (Ti(SO4)2). The obtained powders were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), Fourier transform infrared spectroscopy (FTIR) and ICP plasma spectrometer. EDTA was used as complexing agent to improve the purity and the formation of TiO2 nanoparticles. Experimental results indicated that the high-purity TiO2 nanoparticles were 20 nm in mean size and nearly monodispersed.

  9. Plastic deformation of high-purity a-titanium: model development and validation using the Taylor cylinder impact test

    Science.gov (United States)

    Chandola, Nitin; Revil-Baudard, Benoit; Cazacu, Oana

    2016-08-01

    Results of an experimental study on the quasi-static and high-rate plastic deformation due to impact of a high-purity, polycrystalline, a-titanium material are presented. To quantify the plastic anisotropy and tension-compression asymmetry of the material, first monotonic uniaxial compression and tension tests were carried out at room temperature under quasi-static conditions. It was found that the material is transversely isotropic and displays strong strength differential effects. To characterize the material's strain rate sensitivity, Split Hopkinson Pressure Bar tests in tension and compression were also conducted. Taylor impact tests were performed for impact velocity of 196 m/s. Plastic deformation extended to 64% of the length of the deformed specimen, with little radial spreading. To model simultaneously the observed anisotropy, strain-rate sensitivity, and tension-compression asymmetry of the material, a three-dimensional constitutive model was developed. Key in the formulation is a macroscopic yield function [1] that incorporates the specificities of the plastic flow, namely the combined effects of anisotropy and tension-compression asymmetry. Comparison between model predictions and data show the capabilities of the model to describe with accuracy the plastic behavior of the a-Ti material for both quasi-static and dynamic loadings, in particular, a very good agreement was obtained between the simulated and experimental post-test Taylor specimen geometries.

  10. Microwave-Hydrothermal Synthesis and Characterization of High-Purity Nb Doped BaTiO3 Nanocrystals

    Directory of Open Access Journals (Sweden)

    A. Khanfekr

    2014-01-01

    Full Text Available The synthesis of Nb doped BaTiO3 has been investigated under Microwave-Hydrothermal (MH conditions in the temperature of 150°C for only 2 h using C16H36O4Ti, BaH2O2.8H2O and NbCl5 as Ba, Ti and  Nb sources, respectively.  Typical experiments performed on MH processing have not yet reported for Nb doped BaTiO3.  In the MH process, the formation of high purity nano tetragonal Nb-BaTiO3 was strongly enhanced. New hydrothermal method was used instead of the previous solid state reaction for the BaTiO3±Nb2O3 system. The new method uses high pressure to create nano dimension particles in a lower time and temperature. In case of the phase evolution studies, the XRD pattern measurements and Raman spectroscopy were performed. TEM and FE-SEM images were taken for the detailed analysis of the particle size, surface and morphology.  Synthesis of Nb doped BaTiO3 with the Microwave-hydrothermal provides an advantage of fast crystallization and reduced crystal size when compared to existing methods.

  11. Polytype Stabilization of High-purity Semi-insulating 4H-SiC Crystal via the PVT Method

    Directory of Open Access Journals (Sweden)

    Kai-li MAO

    2016-05-01

    Full Text Available Because the conditions under which semi-insulating 4H-SiC crystals can grow are so specific, other polytypes such as 15R and 6H can easily emerge during the growth process. In this work, a polytype stabilization technology was developed by altering the following parameters: growth temperature, temperature field distribution, and C/Si ratio. In the growth process of high-purity semi-insulating 4H-SiC crystals, the generation of undesirable polytypes was prevented, and a crystal 100 % 4H-SiC polytype was obtained. A high C/Si ratio in powder source was shown to be advantageous for the stabilization of the 4H polytype. Several methods were applied to evaluate the quality of crystals precisely; these methods include Raman mapping, X-ray diffraction, and resistivity mapping. Results showed that the 3inch-wafer was entirely made of 4H polytype, the mean value of FWHM was approximately 40 arcsec, and the distribution of the resistivity value was between 106 Ω×cm and 107 Ω×cm.DOI: http://dx.doi.org/10.5755/j01.ms.22.2.12914

  12. Cobalt(I) Olefin Complexes: Precursors for Metal-Organic Chemical Vapor Deposition of High Purity Cobalt Metal Thin Films.

    Science.gov (United States)

    Hamilton, Jeff A; Pugh, Thomas; Johnson, Andrew L; Kingsley, Andrew J; Richards, Stephen P

    2016-07-18

    We report the synthesis and characterization of a family of organometallic cobalt(I) metal precursors based around cyclopentadienyl and diene ligands. The molecular structures of the complexes cyclopentadienyl-cobalt(I) diolefin complexes are described, as determined by single-crystal X-ray diffraction analysis. Thermogravimetric analysis and thermal stability studies of the complexes highlighted the isoprene, dimethyl butadiene, and cyclohexadiene derivatives [(C5H5)Co(η(4)-CH2CHC(Me)CH2)] (1), [(C5H5)Co(η(4)-CH2C(Me)C(Me)CH2)] (2), and [(C5H5)Co(η(4)-C6H8)] (4) as possible cobalt metal organic chemical vapor deposition (MOCVD) precursors. Atmospheric pressure MOCVD was employed using precursor 1, to synthesize thin films of metallic cobalt on silicon substrates under an atmosphere (760 torr) of hydrogen (H2). Analysis of the thin films deposited at substrate temperatures of 325, 350, 375, and 400 °C, respectively, by scanning electron microscopy and atomic force microscopy reveal temperature-dependent growth features. Films grown at these temperatures are continuous, pinhole-free, and can be seen to be composed of hexagonal particles clearly visible in the electron micrograph. Powder X-ray diffraction and X-ray photoelectron spectroscopy all show the films to be highly crystalline, high-purity metallic cobalt. Raman spectroscopy was unable to detect the presence of cobalt silicides at the substrate/thin film interface.

  13. Experimental Demonstration of Advanced Palladium Membrane Separators for Central High Purity Hydrogen Production

    Energy Technology Data Exchange (ETDEWEB)

    Sean Emerson; Neal Magdefrau; Susanne Opalka; Ying She; Catherine Thibaud-Erkey; Thoman Vanderspurt; Rhonda Willigan

    2010-06-30

    The overall objectives for this project were to: (1) confirm the high stability and resistance of a PdCu trimetallic alloy to carbon and carbide formation and, in addition, resistance to sulfur, halides, and ammonia; (2) develop a sulfur, halide, and ammonia resistant alloy membrane with a projected hydrogen permeance of 25 m{sup 3}m{sup -2}atm{sup -0.5}h{sup -1} at 400 C and capable of operating at pressures of 12.1 MPa ({approx}120 atm, 1750 psia); and (3) construct and experimentally validate the performance of 0.1 kg/day H{sup 2} PdCu trimetallic alloy membrane separators at feed pressures of 2 MPa (290 psia) in the presence of H{sub 2}S, NH{sub 3}, and HCl. This project successfully increased the technology readiness level of palladium-based metallic membranes for hydrogen separation from coal-biomass gasifier exhaust or similar hydrogen-containing gas streams. The reversible tolerance of palladium-copper (PdCu) alloys was demonstrated for H{sub 2}S concentrations varying from 20 ppmv up to 487 ppmv and NH{sub 3} concentrations up to 9 ppmv. In addition, atomistic modeling validated the resistance of PdCu alloys to carbon formation, irreversible sulfur corrosion, and chlorine attack. The experimental program highlighted two key issues which must be addressed as part of future experimental programs: (1) tube defects and (2) non-membrane materials of construction. Four out of five FCC PdCu separators developed leaks during the course of the experimental program because {approx}10% of the alloy tubes contained a single defect that resulted in a thin, weak point in the tube walls. These defects limited operation of the existing tubes to less than 220 psig. For commercial applications of a PdCu alloy hydrogen separator under high sulfur concentrations, it was determined that stainless steel 316 is not suitable for housing or supporting the device. Testing with sulfur concentrations of 487 {+-} 4 ppmv resulted in severe corrosion of the stainless steel components of

  14. Recombinant high-density lipoprotein nanoparticles containing gadolinium-labeled cholesterol for morphologic and functional magnetic resonance imaging of the liver.

    Science.gov (United States)

    Rui, Mengjie; Guo, Wei; Ding, Qian; Wei, Xiaohui; Xu, Jianrong; Xu, Yuhong

    2012-01-01

    Natural high-density lipoproteins (HDL) possess important physiological functions to the transport of cholesterol from the peripheral tissues to the liver for metabolic degradation and excretion in the bile. In this work, we took advantage of this pathway and prepared two different gadolinium (Gd)-DTPA-labeled cholesterol-containing recombinant HDL nanoparticles (Gd-chol-HDL) and Gd-(chol)(2)-HDL as liver-specific magnetic resonance imaging (MRI) contrast agents. The reconstituted HDL nanoparticles had structural similarity to native HDL, and could be taken up by HepG2 cells via interaction with HDL receptors in vitro. In vivo MRI studies in rats after intravenous injections of 10 μmol gadolinium per kg of recombinant HDL nanoparticles indicated that both nanoparticles could provide signal enhancement in the liver and related organs. However, different T(1)-weighted image details suggested that they participated in different cholesterol metabolism and excretion pathways in the liver. Such information could be highly useful to differentiate functional changes as well as anatomic differences in the liver. These cholesterol-derived contrast agents and their recombinant HDL preparations may warrant further development as a new class of contrast agents for MRI of the liver and related organs.

  15. The Development of a Method to Extract High Purity Oxygen From the Martian Atmosphere

    Science.gov (United States)

    Wu, Dongchuan

    1994-01-01

    controlled and therefore proportional to the reciprocal of the membrane thickness. Supported pin hole free Ag membranes with thicknesses of 12 micro m have been developed in this work. Furthermore, a pin hole free Ag membrane that was grown by a combination of Ar ion bombardment assisted physical vapor deposition and intermediate burnishing with a thickness less than 1 micro m is being developed which will substantially improve the oxygen flux level. Thickness of 1 micro m will permit flux levels of at least 106 molecules/cm2s. With this flux level, less than 1.5 m2 membrane surface area would be needed to support an astronaut on a continual basis on the Mars surface. The results of this work show that this approach of producing oxygen from the CO2 Martian atmosphere can eliminate mechanical filtration, compression and high temperature heating of the Mars atmosphere proposed previously by electrochemical methods.

  16. A Process Concept for High-Purity Production of Amines by Transaminase-Catalyzed Asymmetric Synthesis: Combining Enzyme Cascade and Membrane-Assisted ISPR

    DEFF Research Database (Denmark)

    Börner, Tim; Rehn, Gustav; Grey, Carl;

    2015-01-01

    in situ product removal (ISPR) approach using liquid-membrane extraction together with an enzyme cascade. This ISPR strategy facilitates very high (>98%) product purity with an integrated enrichment step and eliminates product as well as coproduct inhibition. In the presented proof-of-concept alanine...

  17. Control of the Gas Flow in an Industrial Directional Solidification Furnace for Production of High Purity Multicrystalline Silicon Ingots

    Directory of Open Access Journals (Sweden)

    Lijun Liu

    2015-01-01

    Full Text Available A crucible cover was designed as gas guidance to control the gas flow in an industrial directional solidification furnace for producing high purity multicrystalline silicon. Three cover designs were compared to investigate their effect on impurity transport in the furnace and contamination of the silicon melt. Global simulations of coupled oxygen (O and carbon (C transport were carried out to predict the SiO and CO gases in the furnace as well as the O and C distributions in the silicon melt. Cases with and without chemical reaction on the cover surfaces were investigated. It was found that the cover design has little effect on the O concentration in the silicon melt; however, it significantly influences CO gas transport in the furnace chamber and C contamination in the melt. For covers made of metal or with a coating on their surfaces, an optimal cover design can produce a silicon melt free of C contamination. Even for a graphite cover without a coating, the carbon concentration in the silicon melt can be reduced by one order of magnitude. The simulation results demonstrate a method to control the contamination of C impurities in an industrial directional solidification furnace by crucible cover design.

  18. GEANT4 simulation of photo-peak efficiency of small high purity germanium detectors for nuclear power plant applications

    Energy Technology Data Exchange (ETDEWEB)

    Rehman, Shakeel Ur; Mirza, Sikander M. [Department of Physics and Applied Mathematics, Pakistan Institute of Engineering and Applied Sciences, Nilore, Islamabad 45650 (Pakistan); Mirza, Nasir M., E-mail: nmm@pieas.edu.p [Department of Physics and Applied Mathematics, Pakistan Institute of Engineering and Applied Sciences, Nilore, Islamabad 45650 (Pakistan); Siddique, Muhammad Tariq [Department of Physics and Applied Mathematics, Pakistan Institute of Engineering and Applied Sciences, Nilore, Islamabad 45650 (Pakistan)

    2011-01-15

    GEANT4 - based Monte Carlo simulations have been carried out for the determination of photo-peak efficiency of heavily shielded small high purity germanium detector (HPGe) used for monitoring radiation levels in nuclear power plants. The GEANT4 simulated values of HPGe detector efficiency for point as well as for disk sources, for two different values of collimator diameter, have been found in good agreement with the corresponding published results obtained by using the MCNP code. The work has been extended to study the effect of radial displacement of a source relative to a detector on photo-peak efficiency for both point and disk source, and at various values of {gamma}-ray energies. Also the effect of disk source radius on photo-peak efficiency has been studied. Besides the results of different available physics models in GEANT4 have also been compared. The computed values of efficiency for point as well as for disk sources using the Penelope and Livermore physics models have been found correspondingly consistent for various values of {gamma}-ray energies while some differences (e.g., Penelope model yields 6.3% higher values of photo-peak efficiency for E{gamma} = 1.332 MeV, 10 mm collimator diameter) have been observed in the corresponding valued obtained by using the Standard physics model.

  19. Inception and propagation of positive streamers in high-purity nitrogen: effects of the voltage rise-rate

    CERN Document Server

    Clevis, T T J; Ebert, U

    2012-01-01

    Controlling streamer morphology is important for numerous applications. Up to now, the effect of the voltage rise rate was only studied across a wide range. Here we show that even slight variations in the voltage rise can have significant effects. We have studied positive streamer discharges in a 16 cm point-plane gap in high-purity nitrogen 6.0, created by 25 kV pulses with a duration of 130 ns. The voltage rise varies by a rise rate from 1.9 kV/ns to 2.7 kV/ns and by the first peak voltage of 22 to 28 kV. A structural link is found between smaller discharges with a larger inception cloud caused by a faster rising voltage. This relation is explained by the greater stability of the inception cloud due to a faster voltage rise, causing a delay in the destabilisation. Time-resolved measurements show that the inception cloud propagates slower than an earlier destabilised, more filamentary discharge. This explains that the discharge with a faster rising voltage pulse ends up to be shorter. Furthermore, the effect...

  20. Effects of carbon, nitrogen, and phosphorus on creep rupture ductility of high purity Ni-Cr austenitic steels

    Energy Technology Data Exchange (ETDEWEB)

    Nakazawa, Takanori; Abo, Hideo; Tanino, Mitsuru; Komatsu, Hazime.

    1989-05-01

    Creep rupture ductility becomes one of the important properties of austenitic stainless steels as structural materials for fast breeder reactors. Using high purity nickel-chromium austenitic steels, the effects of carbon, nitrogen, and phosphorus on creep rupture ductility were investigated. Creep rupture tests were conducted at 600deg C and extensive microstructural works were performed. The results were as follows. Rupture strength increases with carbon or nitrogen content. Although the rupture ductility decreases with carbon, change in ductility with nitrogen is small. The ductility loss with carbon is due to the grain boundary embrittlement by carbides. With nitrogen, there is no precipitation during creep. Addition of phosphorus to ultra low carbon and nitrogen steels increases their rupture strength and ductility. Fine precipitates of (Fe,Cr)/sub 2/P are uniformly dispersed in the grains and coarse (Fe,Cr)/sub 2/P also precipitates on the grain boundary during creep. Grain boundary migration occurs extensively and few wedge type cracks are observed in the P containing steels. It is concluded that, from the viewpoint of increasing creep rupture ductility, nitrogen is much more effective than carbon and phosphorus is also beneficial. (author).

  1. Generation of high-purity human ventral midbrain dopaminergic progenitors for in vitro maturation and intracerebral transplantation.

    Science.gov (United States)

    Nolbrant, Sara; Heuer, Andreas; Parmar, Malin; Kirkeby, Agnete

    2017-09-01

    Generation of precisely patterned neural cells from human pluripotent stem cells (hPSCs) is instrumental in developing disease models and stem cell therapies. Here, we provide a detailed 16-d protocol for obtaining high-purity ventral midbrain (VM) dopamine (DA) progenitors for intracerebral transplantation into animal models and for in vitro maturation into neurons. We have successfully transplanted such cells into the rat; however, in principle, the cells can be used for transplantation into any animal model, and the protocol is designed to also be compatible with clinical transplantation into humans. We show how to precisely set the balance of patterning factors to obtain specifically the caudal VM progenitors that give rise to DA-rich grafts. By specifying how to perform quality control (QC), troubleshooting and adaptation of the procedure, this protocol will facilitate implementation in different laboratories and with a variety of hPSC lines. To facilitate reproducibility of experiments and enable shipping of cells between centers, we present a method for cryopreservation of the progenitors for subsequent direct transplantation or terminal differentiation into DA neurons. This protocol is free of xeno-derived products and can be performed under good manufacturing practice (GMP) conditions.

  2. Cyanex 923 as the extractant in a rare earth element impurity analysis of high-purity cerium oxide.

    Science.gov (United States)

    Duan, Taicheng; Li, Hongfei; Kang, JianZhen; Chen, Hangting

    2004-06-01

    In this work, the feasibility of employing Cyanex 923 as an extractant into the non-cerium REE (rare earth elements) impurity analysis of high-purity cerium oxide was investigated. Through investigations on the choice of the extraction medium, the optimium extraction acidity, matrix Ce4+ effect on the non-cerium REE ion extraction, the optimium extractant concentration and suitable extracting time, and oscillation strengh, it was found that when the phase ratio was at 1:1 and the acicidity was about 2% H2SO4, by gently shaking by hand for about 2 min, 10 mL of 30% Cyanex 923 could not extract even for a 20 ng amount of non-cerium REE3+ ions. However, the extraction efficiency for Ce4+ of 100 mg total amount under the same conditions was about 96%, indicating that a 25-fold preconcentration factor could be achieved. Thus, it was concluded that Cyanex 923 could be used in a REE impurity analysis of 99.9999% or so pure cerium oxide for primary sepapation to elimilate matrix-induced interferences encountered in an ICP-MS (inductively coupled plasma mass spectroscopy) determination.

  3. Direct determination of impurities in high purity silicon carbide by inductively coupled plasma optical emission spectrometry using slurry nebulization technique.

    Science.gov (United States)

    Wang, Zheng; Qiu, Deren; Ni, Zheming; Tao, Guangyi; Yang, Pengyuan

    2006-09-08

    A novel method for the determination of Al, Ca, Cr, Cu, Fe, Mg, Mn, Ni and Ti in high purity silicon carbide (SiC) using slurry introduction axial viewed inductively coupled plasma optical emission spectrometry (ICP-OES) was described. The various sizes of SiC slurry were dispersed by adding dispersant polyethylene imine (PEI). The stability of slurry was characterized by zeta potential measurement, SEM observation and signal stability testing. The optimal concentration of PEI was found to be 0.5 wt% for the SiC slurry. Analytical results of sub-mum size SiC by the slurry introduction were in good accordance with those by the alkaline fusion method which verified that determination could be calibrated by aqueous standards. For mum size SiC, results of most elements have a negative deviation and should be calibrated by the Certified Reference Material slurry. Owing to a rather low contamination in the sample preparation and stability of the slurry, the limits of detection (LODs), which are in the range of 40-2000 ng g(-1), superior to those of the conventional nebulization technique by ICP-OES or ICP-MS.

  4. Design, construction, and operation of a laboratory scale reactorfor the production of high-purity, isotopically enriched bulksilicon

    Energy Technology Data Exchange (ETDEWEB)

    Ager III, J.W.; Beeman, J.W.; Hansen, W.L.; Haller, E.E.

    2004-12-20

    The design and operation of a recirculating flow reactor designed to convert isotopically enriched silane to polycrystalline Si with high efficiency and chemical purity is described. The starting material is SiF{sub 4}, which is enriched in the desired isotope by a centrifuge method and subsequently converted to silane. In the reactor, the silane is decomposed to silicon on the surface of a graphite starter rod (3 mm diameter) heated to 700-750 C. Flow and gas composition (0.3-0.5% silane in hydrogen) are chosen to minimize the generation of particles by homogeneous nucleation of silane and to attain uniform deposition along the length of the rod. Growth rates are 5 {micro}m/min, and the conversion efficiency is greater than 95%. A typical run produces 35 gm of polycrystalline Si deposited along a 150 mm length of the rod. After removal of the starter rod, dislocation-free single crystals are formed by the floating zone method. Crystals enriched in all 3 stable isotopes of Si have been made: {sup 28}Si (99.92%), {sup 29}Si (91.37%), and {sup 30}Si (88.25%). Concentrations of electrically active impurities (P and B) are as low as mid-10{sup 13} cm{sup -3}. Concentrations of C and O lie below 10{sup 16} and 10{sup 15} cm{sup -3}, respectively.

  5. Migration of grain boundaries and triple junctions in high-purity aluminum during annealing after slight cold rolling

    Energy Technology Data Exchange (ETDEWEB)

    Yin, Wenhong [Institute of Materials, Shanghai University, Shanghai 200072 (China); School of Mechanical Engineering, Shandong University of Technology, Zibo 255049 (China); Wang, Weiguo, E-mail: wang_weiguo@vip.163.com [Institute of Materials, Shanghai University, Shanghai 200072 (China); School of Materials Science and Engineering, Fujian University of Technology, Fuzhou 350118 (China); Fang, Xiaoying [School of Mechanical Engineering, Shandong University of Technology, Zibo 255049 (China); Qin, Congxiang [Institute of Materials, Shanghai University, Shanghai 200072 (China); School of Mechanical Engineering, Shandong University of Technology, Zibo 255049 (China); Xing, Xiaoguang [School of Mechanical Engineering, Shandong University of Technology, Zibo 255049 (China)

    2015-09-15

    Grain orientations and grain boundary migrations near triple junctions in a high purity aluminum were analyzed by electron back scattered diffraction. The results indicate that there are good correlations between the Schmid factors or Taylor factors and the misorientation values of point to original point in grains near the triple junctions in a slightly deformed sample. Grains with higher Schmid factors or lower Taylor factors typically correspond to higher misorientation values near the triple junctions. In a subsequent annealing at 400 °C, both grain boundaries and triple junctions migrate, but the former leave ghost lines. During such migration, a grain boundary grows from the grain with lower Schmid factor (higher Taylor factor) into the grain with higher Schmid factor (lower Taylor factor). Usually, the amount of migration of a grain boundary is considerably greater than that of a triple junction, and the grain boundary becomes more curved after migration. These observations indicate that the triple junctions have drag effects on grain boundary migration. - Highlights: • Polycrystalline aluminum with fine grains about 30 μm were used. • Off-line in situ EBSD was used to identify TJs before and after annealing. • Grains with higher SFs have higher misorientation values near TJs after deformation. • Grain boundaries grow from hard grains into soft grains during annealing. • Triple junctions have drag effects on grain boundaries migration.

  6. Production of High-Purity Anhydrous Nickel(II Perrhenate for Tungsten-Based Sintered Heavy Alloys

    Directory of Open Access Journals (Sweden)

    Katarzyna Leszczyńska-Sejda

    2017-04-01

    Full Text Available This paper presents a method for the production of high-purity anhydrous nickel(II perrhenate. The method comprises sorption of nickel(II ions from aqueous nickel(II nitrate solutions, using strongly acidic C160 cation exchange resin, and subsequent elution of sorbed nickel(II ions using concentrated perrhenic acid solutions. After the neutralization of the resulting rhenium-nickel solutions, hydrated nickel(II perrhenate is then separated and then dried at 160 °C to obtain the anhydrous form. The resulting compound is reduced in an atmosphere of dissociated ammonia in order to produce a Re-Ni alloy powder. This study provides information on the selected properties of the resulting Re-Ni powder. This powder was used as a starting material for the production of 77W-20Re-3Ni heavy alloys. Microstructure examination results and selected properties of the produced sintered heavy alloys were compared to sintered alloys produced using elemental W, Re, and Ni powders. This study showed that the application of anhydrous nickel(II perrhenate in the production of 77W-20Re-3Ni results in better properties of the sintered alloys compared to those made from elemental powders.

  7. The Production of High Purity Phycocyanin by Spirulina platensis Using Light-Emitting Diodes Based Two-Stage Cultivation.

    Science.gov (United States)

    Lee, Sang-Hyo; Lee, Ju Eun; Kim, Yoori; Lee, Seung-Yop

    2016-01-01

    Phycocyanin is a photosynthetic pigment found in photosynthetic cyanobacteria, cryptophytes, and red algae. In general, production of phycocyanin depends mainly on the light conditions during the cultivation period, and purification of phycocyanin requires expensive and complex procedures. In this study, we propose a new two-stage cultivation method to maximize the quantitative content and purity of phycocyanin obtained from Spirulina platensis using red and blue light-emitting diodes (LEDs) under different light intensities. In the first stage, Spirulina was cultured under a combination of red and blue LEDs to obtain the fast growth rate until reaching an absorbance of 1.4-1.6 at 680 nm. Next, blue LEDs were used to enhance the concentration and purity of the phycocyanin in Spirulina. Two weeks of the two-stage cultivation of Spirulina yielded 1.28 mg mL(-1) phycocyanin with the purity of 2.7 (OD620/OD280).

  8. S2- behaviors analysis in leaching SrS and precipitating high purity SrCO3 by reduction-decomposition process

    Institute of Scientific and Technical Information of China (English)

    彭晓东; 刘相果; 谢卫东; 刘江; 贾上远; 权燕燕

    2004-01-01

    A new preparation method (reduction-decomposition process) for high purity SrCO3 was investigated,which mainly includes four processes: reduction, leaching, purification and precipitation. The affecting factors about S2- behaviors in leaching process and the effects of variables on purity and particle sizes distribution of SrCO3 were analyzed theoretically and practically. It is concluded that with the increase of temperature or decrease of pH value in leaching process, the strontium recovery increases, but SrS decomposes and hydrogen sulphide (H2S) gasdischarges. The purity of SrCO3 is dependent on dissolution-recrystallization times, for example, the purity of SrCO3 is as high as 99.97% when it is recrystallized three times. Besides, the solution concentration of Sr(OH)2and flow rate of CO2 have important effects on particle size distribution of SrCO3 particles, especially, the particle sizes of SrCO3 meanly distribute in 0.1 - 1.0μm when the flow rate of CO2 is about 2 000 mL/min and other parameters are invariable.

  9. High-purity isolation of anthocyanins mixtures from fruits and vegetables--a novel solid-phase extraction method using mixed mode cation-exchange chromatography.

    Science.gov (United States)

    He, Jian; Giusti, M Monica

    2011-11-04

    Research on biological activity of anthocyanins requires the availability of high purity materials. However, current methods to isolate anthocyanins or anthocyanin mixtures are tedious and expensive or insufficient for complete isolation. We applied a novel cation-exchange/reversed-phase combination solid-phase extraction (SPE) technique, and optimized the use of water/organic buffer mobile phases to selectively separate anthocyanins. Crude extracts of various representative anthocyanin sources were purified with this technique and compared to 3 commonly used SPE techniques: C(18), HLB, and LH-20. Purified anthocyanin fractions were analyzed with high performance liquid chromatography (HPLC) coupled to photodiode array (PDA) and mass spectrometry (MS) detectors and by Fourier transform infrared (FT-IR) spectroscopy. The UV-visible chromatograms quantitatively demonstrated that our novel technique achieved significantly higher (Panthocyanin purity than the C(18) cartridge, the next best method, for 11 of the 12 anthocyanin sources tested. Among them, eight were purified to greater than 99% purity (based on UV-visible chromatograms). The new method efficiently removed non-anthocyanin phenolics. MS and FT-IR results semi-quantitatively confirmed extensive reduction of impurities. Due to strong ionic interaction, our sorbent capacity was superior to others, resulting in the highest throughput and least use of organic solvents. This new methodology for isolation of anthocyanin mixtures drastically increased purity and efficiency while maintaining excellent recovery rate and low cost. The availability of high purity anthocyanin mixtures will facilitate anthocyanin studies and promote the application of anthocyanins in the food and nutraceutical industries.

  10. Production of high-purity isotopes by electromagnetic separation; Production electromagnetique d'isotope tres purs

    Energy Technology Data Exchange (ETDEWEB)

    Cassignol, Ch. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    Improvement in isotopic purity of nuclides prepared by electromagnetic separation is searched into the principle of cascades of monochromators. The principal drawback of which is to allow the separation of only one isotope at a time. The electromagnetic separator of Saclay is equipped with an electrostatic post-analyzer, which is described. Significant results are obtained, concerning isotopic enhancements of uranium-235 and mercury-204. A schema of isotopic contagion is then proposed, the basis of it is the scattering of the primary ions in the residual atmosphere of the separator chamber. The most frequent type of collisions being accompanied by neutralisation of the ions, the schema explains the efficiency of the second stage. As a matter of conclusion, some particularities concerning the routine work at a high enhancement, small output machine, are given. (author) [French] L'accroissement de la purete isotopique des especes nucleaires preparees par separation electromagnetique est recherche dans l'emploi du principe des cascades de monochromateurs, moyennant la servitude de ne collecter qu'un isotope a la fois. Le separateur electromagnetique de Saclay est equipe dans ce but d'un post-analyseur electrostatique, qui est decrit. Des resultats significatifs sont donnes, portant sur les enrichissements obtenus dans les separations d'uranium-235 et de mercure-204. Un schema de contagion isotopique est propose. Il est fonde sur la diffusion a petit angle accompagnant la neutralisation des faisceaux primaires par collision avec le gaz residuel. Ce schema permet d'expliquer l'efficacite de l'etage electrostatique. En matiere de conclusion, la methode d'exploitation d'une machine a faible debit et a haut enrichissement est donnee. (auteur)

  11. Unique low-molecular-weight lignin with high purity extracted from wood by deep eutectic solvents (DES): a source of lignin for valorization

    Energy Technology Data Exchange (ETDEWEB)

    Alvarez-Vasco, Carlos; Ma, Ruoshui; Quintero, Melissa; Guo, Mond; Geleynse, Scott; Ramasamy, Karthikeyan K.; Wolcott, Michael; Zhang, Xiao

    2016-01-01

    This paper reports a new method of applying Deep Eutectic Solvents (DES) for extracting lignin from woody biomass with high yield and high purity. DES mixtures prepared from Choline Chloride (ChCl) and four hydrogen-bond donors–acetic acid, lactic acid, levulinic acid and glycerol–were evaluated for treatment of hardwood (poplar) and softwood (D. fir). It was found that these DES treatments can selectively extract a significant amount of lignin from wood with high yields: 78% from poplar and 58% from D. fir. The extracted lignin has high purity (95%) with unique structural properties. We discover that DES can selectively cleave ether linkages in wood lignin and facilitate lignin removal from wood. The mechanism of DES cleavage of ether bonds between phenylpropane units was investigated. The results from this study demonstrate that DES is a promising solvent for wood delignification and the production of a new source of lignin with promising potential applications.

  12. Merging of the 4F3/2 level states of Nd3+ ions in the photoluminescence spectra of gadolinium-gallium garnets under high pressure

    Science.gov (United States)

    Kaminska, A.; Buczko, R.; Paszkowicz, W.; Przybylińska, H.; Werner-Malento, E.; Suchocki, A.; Brik, M.; Durygin, A.; Drozd, V.; Saxena, S.

    2011-08-01

    The 4F3/2 state of Nd3+ dopant ions is split due to the crystal field at orthorhombic D2 symmetry sites in several members of the garnet family of crystals. In the gadolinium-gallium garnet crystal this splitting is found to almost disappear under hydrostatic pressures between 8 and 11 GPa created in the diamond-anvil cell. This pressure is much lower than that required for the phase transition to the so called high-pressure phase. This effect is explained with help of x-ray diffraction, optical spectroscopy, and ab initio calculations as an effect of accidental near-degeneracy arising from a particular lattice structure of garnets.

  13. Simultaneous determination of seven impurities in high-purity cobalt oxide by ICP-AES after matrix separation using 1-nitroso-2-naphthol as a precipitant

    Institute of Scientific and Technical Information of China (English)

    王艳; 周春山; 段青兵; 陈萍

    2002-01-01

    A method was developed for the simultaneous determination of seven trace impurities (Cd, Mn, Pb, Zn, Cu, Fe and Ni) in high-purity cobalt oxide by ICP-AES. The matrix effect was eliminated by preci- pitation with 1-nitroso-2-naphthol. The matrix effect of cobalt on the absorptions of trace impurities, the effects of reaction time, pH value, dosage of precipitant on the formation of cobalt-1-nitroso-2-naphthol complex, the effects of hydrochloric acid on the stability of this complex and masking of elements were studied. Recoveries of the impurities in spiked sample are from 90% to 110% with a precision of 1.1%-5.0% RSD. The detection limits of the seven elements are in the range of 0.01-0.24μg/g. The method can be applied to the analysis of high-purity cobalt metal, cobalt oxide and other cobalt compounds.

  14. Determination of trace selenium in high purity tellurium by hydride generation atomic fluorescence spectrometry after solid phase extraction of a diaminobenzidine-selenium chelate

    Science.gov (United States)

    Tong, Wang; Ying, Zeng; Jinyong, Xu

    2016-09-01

    Macroporous adsorption resin was used as the sorbent for solid phase extraction and determination of the trace Se content in high purity tellurium prior to hydride generation atomic fluorescence spectrometry analysis. Selenium was converted into an organic Se chelate using 3,3‧-diaminobenzidine and was separated from the tellurium matrix by solid phase extraction. The resin was packed as a column for solid phase extraction. Under optimum conditions, trace Se can be quantitatively extracted and the tellurium matrix can be removed. The Se in the eluate was determined by hydride generation atomic fluorescence spectrometry. The limit of detection (3σ) of this method was 0.22 ng g- 1 and the relative standard deviation (RSD, n = 5) ranged from 2.0 to 2.5% for the three investigated tellurium samples. The proposed method was successfully applied for the determination of the trace Se content in high purity tellurium samples.

  15. Effects of 600 MeV proton irradiation on nucleation and growth of precipitates and helium bubbles in a high-purity Al-Mg-Si alloy

    DEFF Research Database (Denmark)

    Singh, Bachu Narain; Leffers, Torben; Victoria, M.;

    1986-01-01

    Solution treated specimens of a high-purity Al-0.75%Mg-0.42%Si alloy were irradiated with 600 MeV protons at 150 and 240°C to a dose level of 0.47 and 0.55 dpa, respectively. Mg2Si-type precipitates formed during irradiation at 150 and 240°C; at 240°C, however, a large number of precipitates seem...

  16. Gadolinium: Central Metal of the Lanthanoids

    Science.gov (United States)

    Laing, Michael

    2009-01-01

    The physical and chemical properties of gadolinium are compared with those of the other lanthanoids. Some properties are intermediate between those of lanthanum and lutetium; some between those of barium and hafnium; and others (unexpectedly) between those of ytterbium and lutetium. Both the remarkably high molar heat capacity of the metal and the…

  17. Ionic liquid-based extraction followed by graphite-furnace atomic absorption spectrometry for the determination of trace heavy metals in high-purity iron metal.

    Science.gov (United States)

    Matsumiya, Hiroaki; Kato, Tatsuya; Hiraide, Masataka

    2014-02-01

    The analysis of high-purity materials for trace impurities is an important and challenging task. The present paper describes a facile and sensitive method for the determination of trace heavy metals in high-purity iron metal. Trace heavy metals in an iron sample solution were rapidly and selectively preconcentrated by the extraction into a tiny volume of an ionic liquid [1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide] for the determination by graphite-furnace atomic absorption spectrometry (GFAAS). A nitrogen-donating neutral ligand, 2,4,6-tris(2-pyridyl)-1,3,5-triazine (TPTZ), was found to be effective in the ionic liquid-based selective extraction, allowing the nearly complete (~99.8%) elimination of the iron matrix. The combination with the optimized GFAAS was successful. The detectability reached sub-μg g(-1) levels in iron metal. The novel use of TPTZ in ionic liquid-based extraction followed by GFAAS was successfully applied to the determination of traces of Co, Ni, Cu, Cd, and Pb in certified reference materials for high-purity iron metal. © 2013 Published by Elsevier B.V.

  18. Optimal recovery of high-purity rutin crystals from the whole plant of Fagopyrum esculentum Moench (buckwheat) by extraction, fractionation, and recrystallization.

    Science.gov (United States)

    Kim, Kyoung Heon; Lee, Ki Won; Kim, Dong Young; Park, Hyung Hwan; Kwon, Ik Boo; Lee, Hyong Joo

    2005-10-01

    Rutin, one of the flavonoids derived from plants, is increasingly in demand in the food, pharmaceutical, and cosmetic industries due to its various biological and physiological activities including antioxidation, anti-inflammation, and anti-hypertension. The whole plant of buckwheat (Fagopyrum esculentum Moench) is a major source of natural rutin. This study developed a low-cost process encompassing the efficient extraction, fractionation, and recrystallization to obtain high-purity rutin from buckwheat, and it could improve the economic utilization of this abundant low-value agricultural product. The sequential separation and purification procedures established in this study involved extraction with 50% (v/v) aqueous ethanol at 80 degrees C for 1 h followed by elution with water and aqueous ethanols at 20% and 30% (v/v) on a styrene-based resin column, and recrystallization at 4 degrees C for 12 h. These conditions resulted in the recovery of 92% of total rutin with over 95% purity. In the present study, high-purity rutin was obtained from whole buckwheat through low-cost processes, the separation and purification strategy established in this study could provide valuable information to the relevant industries.

  19. A hybrid enrichment process combining conjugated polymer extraction and silica gel adsorption for high purity semiconducting single-walled carbon nanotubes (SWCNT)

    Science.gov (United States)

    Ding, Jianfu; Li, Zhao; Lefebvre, Jacques; Cheng, Fuyong; Dunford, Jeffrey L.; Malenfant, Patrick R. L.; Humes, Jefford; Kroeger, Jens

    2015-09-01

    A novel purification process for the enrichment of sc-SWCNTs that combines selective conjugated polymer extraction (CPE) with selective adsorption using silica gel, termed hybrid-CPE (h-CPE), has been developed, providing a high purity sc-SWCNT material with a significant improvement in process efficiency and yield. Using the h-CPE protocol, a greater than 5 fold improvement in yield can be obtained compared to traditional CPE while obtaining sc-SWCNT with a purity >99.9% as assessed by absorption spectroscopy and Raman mapping. Thin film transistor devices using the h-CPE derived sc-SWCNTs as the semiconductor possess mobility values ranging from 10-30 cm2 V-1 s-1 and current ON/OFF ratio of 104-105 for channel lengths between 2.5 and 20 μm.A novel purification process for the enrichment of sc-SWCNTs that combines selective conjugated polymer extraction (CPE) with selective adsorption using silica gel, termed hybrid-CPE (h-CPE), has been developed, providing a high purity sc-SWCNT material with a significant improvement in process efficiency and yield. Using the h-CPE protocol, a greater than 5 fold improvement in yield can be obtained compared to traditional CPE while obtaining sc-SWCNT with a purity >99.9% as assessed by absorption spectroscopy and Raman mapping. Thin film transistor devices using the h-CPE derived sc-SWCNTs as the semiconductor possess mobility values ranging from 10-30 cm2 V-1 s-1 and current ON/OFF ratio of 104-105 for channel lengths between 2.5 and 20 μm. Electronic supplementary information (ESI) available. See DOI: 10.1039/c5nr04851f

  20. Development and validation of high performance liquid chromatography with a spectrophotometric detection method for the chemical purity and assay of nepafenac.

    Science.gov (United States)

    Lipiec-Abramska, Elżbieta; Jedynak, Łukasz; Formela, Adam; Roszczyński, Jacek; Cybulski, Marcin; Puchalska, Maria; Zagrodzka, Joanna

    2014-03-01

    The study is a proposition of the application of high performance liquid chromatography (HPLC) with a spectrophotometric UV range detector to analyze the chemical purity and assay of nepafenac, an active pharmaceutical ingredient (API). During literature search only a few publications were found about nepafenac. HPLC UV methods were mainly presented in patent documents about nepafenac synthesis and chemical purity. The presented method allows to separate all potential related compounds from nepafenac and to quantitate the nepafenac amount. As there is no official monograph in the pharmacopeias about nepafenac, the performed full validation procedure makes the method ready to use in routine analysis. The composition of the mobile phase (10mM ammonium formate, pH 4.1) and the HPLC column (Phenomenex Gemini-NX C18) were selected during the development step. Presented data confirm the benefits of the developed method. Four of the most potential impurities were validated as for the quantitative test and the rest of impurities were validated as for the limit test - according to ICH Q2(R1). The accuracy/recovery results for the chemical purity method are within 90-108%, in the case of assay studies from 99% to 101%; the limit of detection is as low as 15-30ng/mL. The linearity passes all statistical tests. Copyright © 2013 Elsevier B.V. All rights reserved.

  1. A comparison of a novel robust decentralised control strategy and MPC for industrial high purity, high recovery, multicomponent distillation.

    Science.gov (United States)

    Udugama, Isuru A; Wolfenstetter, Florian; Kirkpatrick, Robert; Yu, Wei; Young, Brent R

    2017-07-01

    In this work we have developed a novel, robust practical control structure to regulate an industrial methanol distillation column. This proposed control scheme is based on a override control framework and can manage a non-key trace ethanol product impurity specification while maintaining high product recovery. For comparison purposes, a MPC with a discrete process model (based on step tests) was also developed and tested. The results from process disturbance testing shows that, both the MPC and the proposed controller were capable of maintaining both the trace level ethanol specification in the distillate (XD) and high product recovery (β). Closer analysis revealed that the MPC controller has a tighter XD control, while the proposed controller was tighter in β control. The tight XD control allowed the MPC to operate at a higher XD set point (closer to the 10ppm AA grade methanol standard), allowing for savings in energy usage. Despite the energy savings of the MPC, the proposed control scheme has lower installation and running costs. An economic analysis revealed a multitude of other external economic and plant design factors, that should be considered when making a decision between the two controllers. In general, we found relatively high energy costs favour MPC. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

  2. Unimodal transform of variables selected by interval segmentation purity for classification tree modeling of high-dimensional microarray data.

    Science.gov (United States)

    Du, Wen; Gu, Ting; Tang, Li-Juan; Jiang, Jian-Hui; Wu, Hai-Long; Shen, Guo-Li; Yu, Ru-Qin

    2011-09-15

    As a greedy search algorithm, classification and regression tree (CART) is easily relapsing into overfitting while modeling microarray gene expression data. A straightforward solution is to filter irrelevant genes via identifying significant ones. Considering some significant genes with multi-modal expression patterns exhibiting systematic difference in within-class samples are difficult to be identified by existing methods, a strategy that unimodal transform of variables selected by interval segmentation purity (UTISP) for CART modeling is proposed. First, significant genes exhibiting varied expression patterns can be properly identified by a variable selection method based on interval segmentation purity. Then, unimodal transform is implemented to offer unimodal featured variables for CART modeling via feature extraction. Because significant genes with complex expression patterns can be properly identified and unimodal feature extracted in advance, this developed strategy potentially improves the performance of CART in combating overfitting or underfitting while modeling microarray data. The developed strategy is demonstrated using two microarray data sets. The results reveal that UTISP-based CART provides superior performance to k-nearest neighbors or CARTs coupled with other gene identifying strategies, indicating UTISP-based CART holds great promise for microarray data analysis.

  3. Motexafin gadolinium: gadolinium (III) texaphyrin, gadolinium texaphyrin, Gd-Tex, GdT2B2, PCI 0120.

    Science.gov (United States)

    2004-01-01

    Motexafin gadolinium [gadolinium (III) texaphyrin, gadolinium texaphyrin, Gd-Tex, GdT2B2, PCI 0120] is a radiosensitising agent developed for use in cancer therapy. It is cytotoxic in haematological malignancies by selectively localising in cancer cells that have high rates of metabolism. Motexafin gadolinium inhibits cellular respiration resulting in the production of reactive oxygen species and inducing apoptosis. It is being developed by Pharmacyclics in the US. Bulk motexafin gadolinium is supplied to Pharmacyclics by the US company, Celanese, through a manufacturing and supply agreement between the two companies. In June 2003, at the 39th Annual Meeting of the American Society of Clinical Oncology (ASCO-2003), the importance of having an agent for the treatment of brain metastases from lung cancer was highlighted. Results of a phase III study were presented that showed that motexafin gadolinium treatment was associated with a delay in time to neurological and neurocognitive progression in lung cancer patients. This was an important finding, as 46.6% of lung cancer patients already have brain metastases at the time of initial diagnosis, compared with only 2.7% of breast cancer patients. Brain metastases are also often the only site of metastatic disease in patients with lung cancer. In December 2002, Pharmacyclics began a phase III trial of motexafin gadolinium in patients with brain metastases (brain cancer in phase table) from lung cancer in the US, Europe, Canada and Australia. The trial is known as the Study of neurologic progression with Motexafin gadolinium And Radiation Therapy (SMART) and will compare whole-brain irradiation with whole-brain irradiation plus motexafin gadolinium in 550 patients. The primary efficacy endpoint is time to neurological progression and the secondary endpoints are survival and neurocognitive function. In January 2003, the US FDA completed its Special Protocol Assessment (SPA) of the SMART trial with a positive result and by

  4. Measurement of the high-field Q drop in a high-purity large-grain niobium cavity for different oxidation processes

    Directory of Open Access Journals (Sweden)

    G. Ciovati

    2007-06-01

    Full Text Available The most challenging issue for understanding the performance of superconducting radio-frequency (rf cavities made of high-purity (residual resistivity ratio >200 niobium is due to a sharp degradation (“Q-drop” of the cavity quality factor Q_{0}(B_{p} as the peak surface magnetic field (B_{p} exceeds about 90 mT, in the absence of field emission. In addition, a low-temperature (100–140°C in situ baking of the cavity was found to be beneficial in reducing the Q-drop. In this contribution, we present the results from a series of rf tests at 1.7 and 2.0 K on a single-cell cavity made of high-purity large (with area of the order of few cm^{2} grain niobium which underwent various oxidation processes, after initial buffered chemical polishing, such as anodization, baking in pure oxygen atmosphere, and baking in air up to 180°C, with the objective of clearly identifying the role of oxygen and the oxide layer on the Q-drop. During each rf test a temperature mapping system allows measuring the local temperature rise of the cavity outer surface due to rf losses, which gives information about the losses location, their field dependence, and space distribution. The results confirmed that the depth affected by baking is about 20–30 nm from the surface and showed that the Q-drop did not reappear in a previously baked cavity by further baking at 120°C in pure oxygen atmosphere or in air up to 180°C. These treatments increased the oxide thickness and oxygen concentration, measured on niobium samples which were processed with the cavity and were analyzed with transmission electron microscope and secondary ion mass spectroscopy. Nevertheless, the performance of the cavity after air baking at 180°C degraded significantly and the temperature maps showed high losses, uniformly distributed on the surface, which could be completely recovered only by a postpurification treatment at 1250°C. A statistic of the position of the “hot spots” on the

  5. Measurement of the high-field Q-drop in a high-purity large-grain niobium cavity for different oxidation processes

    Energy Technology Data Exchange (ETDEWEB)

    Ciovati, Gianluigi; Kneisel, Peter; gurevich, alex

    2007-06-01

    The most challenging issue for understanding the performance of superconducting radio-frequency (rf) cavities made of high-purity (residual resistivity ratio > 200) niobium is due to a sharp degradation (“Q-drop”) of the cavity quality factor Q0(Bp) as the peak surface magnetic field (Bp) exceeds about 90 mT, in the absence of field emission. In addition, a low-temperature (100 – 140 C) “in-situ” baking of the cavity was found to be beneficial in reducing the Q-drop. In this contribution, we present the results from a series of rf tests at 1.7 K and 2.0 K on a single-cell cavity made of high-purity large (with area of the order of few cm2) grain niobium which underwent various oxidation processes, after initial buffered chemical polishing, such as anodization, baking in pure oxygen atmosphere and baking in air up to 180 °C, with the objective of clearly identifying the role of oxygen and the oxide layer on the Q-drop. During each rf test a temperature mapping system allows measuring the local temperature rise of the cavity outer surface due to rf losses, which gives information about the losses location, their field dependence and space distribution. The results confirmed that the depth affected by baking is about 20 – 30 nm from the surface and showed that the Q-drop did not re-appear in a previously baked cavity by further baking at 120 °C in pure oxygen atmosphere or in air up to 180 °C. These treatments increased the oxide thickness and oxygen concentration, measured on niobium samples which were processed with the cavity and were analyzed with Transmission Electron Microscope (TEM) and Secondary Ion Mass Spectroscopy (SIMS). Nevertheless, the performance of the cavity after air baking at 180 °C degraded significantly and the temperature maps showed high losses, uniformly distributed on the surface, which could be completely recovered only by a post-purification treatment at 1250 °C. A statistic of the position of the “hot-spots” on the

  6. Trace elements study of high purity nanocrystalline silicon carbide (3C-SiC) using k0-INAA method

    Science.gov (United States)

    Huseynov, Elchin; Jazbec, Anze

    2017-07-01

    Silicon carbide (3C-SiC) nanoparticles have been irradiated by neutron flux (2×1013 n·cm-2·s-1) at TRIGA Mark II type research reactor. After neutron irradiation, the radioisotopes of trace elements in the nanocrystalline 3C-SiC were studied as time functions. The identification of isotopes which significantly increased the activity of the samples as a result of neutron radiation was carried out. Nanocrystalline 3C-SiC are synthesized by standard laser technique and the purity of samples was determined by the k0-based Instrumental Neutron Activation Analysis (k0-INAA) method. Trace elements concentration in the 3C-SiC nanoparticles were determined by the radionuclides of appropriate elements. The trace element isotopes concentration have been calculated in percentage according to k0-INAA method.

  7. Influence of power density on high purity 63 mm diameter polycrystalline diamond deposition inside a 2.45 GHz MPCVD reactor

    Science.gov (United States)

    Yu, Shengwang; Wang, Rong; Zheng, Ke; Gao, Jie; Li, Xiaojing; Hei, Hongjun; Liu, Xiaoping; He, Zhiyong; Shen, Yanyan; Tang, Bin

    2016-09-01

    63 mm diameter polycrystalline diamond (PCD) films were synthesized via a microwave plasma chemical vapor deposition (MPCVD) reactor in 99% H2-1% CH4 atmosphere. Two different conditions, i.e. the typical condition (input power of 5 kW and gas pressure of 13 kPa) and the high power density condition (input power of 10 kW and gas pressure of 18 kPa), were employed for diamond depositions. The color changes of the plasma under the two proposed conditions with and without methane were observed by photographs. Likewise, the concentrations of hydrogen atoms and carbon active chemical species in plasma were analyzed by optical emission spectroscopy (OES). The morphologies and purity of the PCD films were investigated by scanning electron microscopy (SEM) and Raman spectroscopy, respectively. Finally, the transmission spectrum of the polished PCD plates was characterized by a UV-Vis-NIR spectrometer. Experimental results showed that both the concentrations of hydrogen atoms and carbon radicals increased obviously, with the boost input power and higher pressure. The films synthesized under the high power density condition displayed higher purity and more uniform thickness. The growth rates in 10 kW and 18 kPa reached ~7.7 µm h-1, approximately 6.5 times as much as that occurred in the typical process. Moreover, the polished plates synthesized under the high power density condition possessed a relatively high optical transmittance (~69%), approaching the theoretical values of approximately 71.4% in IR. These results indicate that the purity and growth rate of big-area PCD films could be simultaneously increased with power density.

  8. In an animal model nephrogenic systemic fibrosis cannot be induced by intraperitoneal injection of high-dose gadolinium based contrast agents

    Energy Technology Data Exchange (ETDEWEB)

    Langer, R.D., E-mail: rlanger@uaeu.ac.ae [Faculty of Medicine and Health Sciences (FMHS), United Arab Emirates University, Al Ain (United Arab Emirates); Lorke, D.E. [Florida International University, Miami, FL (United States); Neidl van Gorkom, K.F. [Faculty of Medicine and Health Sciences (FMHS), United Arab Emirates University, Al Ain (United Arab Emirates); Petroianu, G. [Florida International University, Miami, FL (United States); Azimullah, S.; Nurulain, S.M.; Singh, S. [Faculty of Medicine and Health Sciences (FMHS), United Arab Emirates University, Al Ain (United Arab Emirates); Fuchsjäger, M. [Al Ain Hospital, MUV-VAMED, Al Ain (United Arab Emirates)

    2012-10-15

    Aim and objective: Nephrogenic systemic fibrosis (NSF) has been reported in humans to be most likely induced by gadolinium based contrast agents (GBCA), namely by gadodiamide, gadopentetate dimeglumine, and gadoversetamide, rarely by other GBCA. The pathogenesis of NSF remains unclear; different hypotheses are under discussion. The objective of the study is to assess if in the animal model human-like NSF changes can be induced by high-dose, intraperitoneal GBCA injections over four weeks. Materials and methods: After approval by the institutional animal ethics committee, six rats each were randomly assigned to groups, and treated with seven different GBCA. Intraperitoneal (IP) injections – proven in the animal model to be effective – were chosen to prolong the animals’ exposure to the respective GBCA. GBCA doses of previous intravenous (IV) animal studies were applied. After five weeks all rats were sacrificed. Sham controls were treated with IP saline injections, employing the same regimen. Results: No findings comparable with human NSF were observed in all animals after IP treatment with all seven GBCA at daily doses of 2.5 and 5.0 mmol/kg body weight (BW). No histopathological abnormalities of all examined organs were noted. Weight loss was stated in weeks three and four with GBCA injections at doses of 5.0 mmol/kg BW, but rats regained weight after cessation of GBCA treatment. Conclusions: NSF-comparable pathological findings could not be induced by high dose intraperitoneal injection of seven GBCA.

  9. 高纯α-AlH3的合成及表征%Synthesis and Characterization of α-AlH3 with High Purity

    Institute of Scientific and Technical Information of China (English)

    张永岗; 开永茂; 汪伟; 邱少君; 李鸿波

    2012-01-01

    为制备高纯α-AlH3,将LiAlH4与AlCl3在乙醚溶液中反应,制备并分离出固体AlH3乙醚络合物,其在甲苯中90℃下脱醚2h可制得纯度为99.5%的α-AlH3,产率96.4%.对高纯α-AlH3进行了XRD、红外、元素分析、TG/DSC、SEM表征,同时考察了α-AlH3的结晶条件和稳定性.结果表明产品结晶性好、纯度高、性质稳定,合成方法具有操作简便、收率高、重现性好等优点.%In order to obtain α-AlH3 with high purity, solid AlH3-etherate was synthesized and separated from the reaction of LiAlH4 and A1C13 in diethyl ether, then α-A1H3 with purity of 99. 5 % was prepared via desolvation of the solid AlH3-etherate in toluene at 90℃ for 2 hours in the yield of 96. 4%. The product was characterized by XRD, IR, elemental analysis, TG/DSC, SEM, meanwhile the crystallization and stability of α-AlH3 was also studied. The results indicate that the product has good crystallization, high purity and stability, the synthetic method has the advantages of simple operation, high yield and good reproducibility.

  10. Progress in Catalytic Membrane Reactors for High Purity Hydrogen Production%膜催化反应器及其制氢技术的研究进展

    Institute of Scientific and Technical Information of China (English)

    闫云飞; 张力; 李丽仙; 唐强

    2011-01-01

    As a kind of ideal fuel for fuel cell, hydrogen must be satisfied with the enough high purity. To produce high purity hydrogen at a low cost and large scale method has become a key research focus in the industrialization of fuel-cell technology. The membrane catalytic technology with catalysis and separation dual functions has been developed in recent years, which is a good method to produce high purity hydrogen. Based on the latest developments in the membrane catalytic reaction fields, the advantages, composition and type of membrane catalytic reactor are summarized. The preparation techniques, advantages and classification of inorganic membrane materials are described. Especially, the progress and application for high purity hydrogen production are reviewed in three kinds of catalytic membrane reactors, including oxygen-permeable membrane reactor, hydrogen-permeation membrane reactor and double-membranes reactor. The existing problems of catalytic membrane and membrane catalytic reactor in the industrialization process of hydrogen production using the membrane catalytic technology are also discussed. Additionally, the prospects of membrane catalytic reactors for hydrogen production is proposed.%燃料电池对其理想燃料氢气的纯度要求极高,如何低成本、大规模制取高纯氢气己成为燃料电池技术实现工业化的一个关键问题和研究热点.近年发展起来的兼具催化与分离双重功能的膜催化反应技术是实现制取高纯氢气的一个有效途径.本文结合膜催化反应领域的最新进展,综述了膜催化反应器的优点、组成、类型;介绍了无机膜材料的优点、分类及制备技术;详细综述了透氧膜催化反应器、透氢膜催化反应器及双膜催化反应器在制氢过程中的研究进展和应用,指出了膜催化反应制氢技术在工业化发展过程中存在的问题及应用前景.

  11. A study on the influence of trace elements (C, S, B, Al, N) on the hot ductility of the high purity austenitic alloy Fe-Ni 36% (INVAR)

    Energy Technology Data Exchange (ETDEWEB)

    Simonetta-Perrot, M.T.

    1994-11-01

    In order to study the damage mechanisms leading to the ductility decrease of the Invar alloy at 600 C, a high-purity Fe-Ni 36% sample has been doped with trace elements with the purpose of identifying the role of sulfur, sulfur with Al N or B N precipitates and sulfur with boron, on the ductility, the failure modes, the intergranular damage and the plastic deformation mechanisms prior to failure. A new AES segregation quantification method has been used to study the kinetics and thermodynamics of intergranular and surface segregations and determine the relation between sulfur segregation and grain joint fragility. refs., figs., tabs.

  12. Effect of Carbon on Grain Boundary Segregation of Phosphorus and Phosphorus-Induced Intergranular Fracture in High Purity Iron with Phosphorus

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    The segregation of carbon at grain boundaries and its effect on phosphorus segregation and phosphorus-induced intergranular fracture in the alloy of high purity iron with phosphorus were investigated by scanning Auger electron spectroscopy, impact test and SEM observation of fractured surface. The experimental results showed that the carbon segregation at grain boundaries decreases the phosphorus segregation, and a change of fracture mode from intergranular fracture to transgranular one, hence a decrease of ductile-brittle transition temperature is observed. The mechanism of these effects was discussed.

  13. Characteristics of Signals Originating Near the Lithium-Diffused N+ Contact of High Purity Germanium P-Type Point Contact Detectors

    CERN Document Server

    Aguayo, E; Avignone, F T; Barabash, A S; Barton, P J; Beene, J R; Bertrand, F E; Boswell, M; Brudanin, V; Busch, M; Chan, Y-D; Christofferson, C D; Collar, J I; Combs, D C; Cooper, R J; Detwiler, J A; Doe, P J; Efremenko, Yu; Egorov, V; Ejiri, H; Elliott, S R; Esterline, J; Fast, J E; Fields, N; Finnerty, P; Fraenkle, F M; Galindo-Uribarri, A; Gehman, V M; Giovanetti, G K; Green, M P; Guiseppe, V E; Gusey, K; Hallin, A L; Hazama, R; Henning, R; Hoppe, E W; Horton, M; Howard, S; Howe, M A; Johnson, R A; Keeter, K J; Kidd, M F; Knecht, A; Kochetov, O; Konovalov, S I; Kouzes, R T; LaFerriere, B D; Leon, J; Leviner, L E; Loach, J C; Looker, Q; Luke, P N; MacMullin, S; Marino, M G; Martin, R D; Merriman, J H; Miller, M L; Mizouni, L; Nomachi, M; Orrell, J L; Overman, N R; Perumpilly, G; Phillips, D G; Poon, A W P; Radford, D C; Rielage, K; Robertson, R G H; Ronquest, M C; Schubert, A G; Shima, T; Shirchenko, M; Snavely, K J; Steele, D; Strain, J; Timkin, V; Tornow, W; Varner, R L; Vetter, K; Vorren, K; Wilkerson, J F; Yakushev, E; Yaver, H; Young, A R; Yu, C -H; Yumatov, V

    2012-01-01

    A study of signals originating near the lithium-diffused n+ contact of p-type point contact (PPC) high purity germanium detectors (HPGe) is presented. The transition region between the active germanium and the fully dead layer of the n+ contact is examined. Energy depositions in this transition region are shown to result in partial charge collection. This provides a mechanism for events with a well defined energy to contribute to the continuum of the energy spectrum at lower energies. A novel technique to quantify the contribution from this source of background is introduced. Experiments that operate germanium detectors with a very low energy threshold may benefit from the methods presented herein.

  14. Characteristics of Signals Originating near the Lithium-Diffused N+ Contact of High Purity Germanium P-Type Point Contact Detectors

    Energy Technology Data Exchange (ETDEWEB)

    Aguayo, E. [Pacific Northwest National Laboratory (PNNL); Amman, M. [Lawrence Berkeley National Laboratory (LBNL); Avignone, F. T. [University of South Carolina/ORNL; Barabash, A.S. [Institute of Theoretical & Experimental Physics, Moscow, Russia; Barton, P. J. [Lawrence Berkeley National Laboratory (LBNL); Beene, James R [ORNL; Bertrand Jr, Fred E [ORNL; Boswell, M. [Los Alamos National Laboratory (LANL); Brudanin, V. [Joint Institute for Nuclear Research, Dubna, Russia; Busch, M. [Duke University; Chan, Y-D [Lawrence Berkeley National Laboratory (LBNL); Christofferson, C. D. [South Dakota School of Mines & Technology, Rapid City, SD; Collar, Juan I. [University of Chicago; Combs, D. C. [University of North Carolina / Triangle Universities Nuclear Lababoratory, Durham; Cooper, Reynold J [ORNL; Detwiler, J.A. [Lawrence Berkeley National Laboratory (LBNL); Doe, P. J. [University of Washington; Efremenko, Yuri [University of Tennessee (UTK) and Oak Ridge National Laboratory (ORNL); Egorov, V. [Joint Institute for Nuclear Research, Dubna, Russia; Ejiri, H. [Osaka University; Elliott, S. R. [Los Alamos National Laboratory (LANL); Esterline, J. [Duke University; Fast, J.E. [Pacific Northwest National Laboratory (PNNL); Fields, N. [University of Chicago; Finnerty, P. [University of North Carolina / Triangle Universities Nuclear Lababoratory, Durham; Fraenkle, F. M. [University of North Carolina / Triangle Universities Nuclear Lababoratory, Durham; Galindo-Uribarri, Alfredo {nmn} [ORNL; Gehman, V. M. [Los Alamos National Laboratory (LANL); Giovanetti, G. K. [Univ, of North Carolina & Triangle Universities Nucl. Lab - Durham, NC; Green, M. P. [University of North Carolina / Triangle Universities Nuclear Lababoratory, Durham; Guiseppe, V.E. [University of South Dakota; Gusey, K. [Joint Institute for Nuclear Research, Dubna, Russia; Hallin, A. L. [University of Alberta, Edmonton, Canada; Hazama, R. [Osaka University; Henning, R. [Univ, of North Carolina & Triangle Universities Nucl. Lab - Durham, NC; Hoppe, E.W. [Pacific Northwest National Laboratory (PNNL); Horton, M. [South Dakota School of Mines & Technology, Rapid City, SD; Howard, S. [South Dakota School of Mines and Technology; Howe, M. A. [University of North Carolina / Triangle Universities Nuclear Lababoratory, Durham; Johnson, R. A. [University of Washington, Seattle; Keeter, K.J. [Black Hills State University, Spearfish, SD; Kidd, M. F. [Los Alamos National Laboratory (LANL); Knecht, A. [University of Washington, Seattle; Kochetov, O. [Joint Institute for Nuclear Research, Dubna, Russia; Konovalov, S.I. [Institute of Theoretical & Experimental Physics, Moscow, Russia; Kouzes, R. T. [Pacific Northwest National Laboratory (PNNL); LaFerriere, B. D. [Pacific Northwest National Laboratory (PNNL); Leon, J. [University of Washington, Seattle; Leviner, L. E. [University of North Carolina / Triangle Universities Nuclear Lababoratory, Durham; Loach, J.C. [Lawrence Berkeley National Laboratory (LBNL); Looker, Q. [Lawrence Berkeley National Laboratory (LBNL); Luke, P.N. [Lawrence Berkeley National Laboratory (LBNL); MacMullin, S. [University of North Carolina / Triangle Universities Nuclear Lababoratory, Durham; Marino, M. G. [University of Washington, Seattle; Martin, R.D. [Lawrence Berkeley National Laboratory (LBNL); Merriman, J. H. [Pacific Northwest National Laboratory (PNNL); Miller, M. L. [University of Washington, Seattle; Mizouni, L. [PPNL/Univ. of South Carolina; Nomachi, M. [Osaka University; Orrell, John L. [Pacific Northwest National Laboratory (PNNL); Overman, N. R. [Pacific Northwest National Laboratory (PNNL); Perumpilly, G. [University of South Dakota; Phillips II, D. G. [University of North Carolina / Triangle Universities Nuclear Lababoratory, Durham; Poon, A.W.P. [Lawrence Berkeley National Laboratory (LBNL); et al.

    2013-01-01

    A study of signals originating near the lithium-diffused n+ contact of p-type point contact (PPC) high purity germanium detectors (HPGe) is presented. The transition region between the active germanium and the fully dead layer of the n+ contact is examined. Energy depositions in this transition region are shown to result in partial charge collection. This provides a mechanism for events with a well defined energy to contribute to the continuum of the energy spectrum at lower energies. A novel technique to quantify the contribution from this source of background is introduced. Experiments that operate germanium detectors with a very low energy threshold may benefit from the methods presented herein.

  15. A study on the influence of trace elements (C, S, B, Al, N) on the hot ductility of the high purity austenitic alloy Fe-Ni 36% (INVAR)

    Energy Technology Data Exchange (ETDEWEB)

    Simonetta-Perrot, M.T.

    1994-11-01

    In order to study the damage mechanisms leading to the ductility decrease of the Invar alloy at 600 C, a high-purity Fe-Ni 36% sample has been doped with trace elements with the purpose of identifying the role of sulfur, sulfur with Al N or B N precipitates and sulfur with boron, on the ductility, the failure modes, the intergranular damage and the plastic deformation mechanisms prior to failure. A new AES segregation quantification method has been used to study the kinetics and thermodynamics of intergranular and surface segregations and determine the relation between sulfur segregation and grain joint fragility. refs., figs., tabs.

  16. Preparation of High Purity, High Molecular-Weight Chitin from Ionic Liquids for Use as an Adsorbate for the Extraction of Uranium from Seawater

    Energy Technology Data Exchange (ETDEWEB)

    Rogers, Robin [Univ. of Alabama, Tuscaloosa, AL (United States)

    2013-12-21

    Ensuring a domestic supply of uranium is a key issue facing the wider implementation of nuclear power. Uranium is mostly mined in Kazakhstan, Australia, and Canada, and there are few high-grade uranium reserves left worldwide. Therefore, one of the most appealing potential sources of uranium is the vast quantity dissolved in the oceans (estimated to be 4.4 billion tons worldwide). There have been research efforts centered on finding a means to extract uranium from seawater for decades, but so far none have resulted in an economically viable product, due in part to the fact that the materials that have been successfully demonstrated to date are too costly (in terms of money and energy) to produce on the necessary scale. Ionic Liquids (salts which melt below 100{degrees}C) can completely dissolve raw crustacean shells, leading to recovery of a high purity, high molecular weight chitin powder and to fibers and films which can be spun directly from the extract solution suggesting that continuous processing might be feasible. The work proposed here will utilize the unprecedented control this makes possible over the chitin fiber a) to prepare electrospun nanofibers of very high surface area and in specific architectures, b) to modify the fiber surfaces chemically with selective extractant capacity, and c) to demonstrate their utility in the direct extraction and recovery of uranium from seawater. This approach will 1) provide direct extraction of chitin from shellfish waste thus saving energy over the current industrial process for obtaining chitin; 2) allow continuous processing of nanofibers for very high surface area fibers in an economical operation; 3) provide a unique high molecular weight chitin not available from the current industrial process, leading to stronger, more durable fibers; and 4) allow easy chemical modification of the large surface areas of the fibers for appending uranyl selective functionality providing selectivity and ease of stripping. The

  17. Preparation of High-purity Copper Xxide for Electroplating%电镀用高纯氧化铜的合成方法

    Institute of Scientific and Technical Information of China (English)

    闫静; 王学炜; 王宇

    2015-01-01

    Basic copper carbonate was prepared with copper nitrate and ammonium bicarbonate as raw materials. Then active copper oxide was prepared by basic copper carbonate after high-temperature roasting. The properties of the active copper oxide were characterized by X-ray diffraction (XRD), purity determination and inductively coupled plasma atomic emission spectroscopy (ICP-AES). The purity of active copper oxide prepared by this method could reach more than 99.3%, higher than the universal national standard of analytical reagent. And impurity content was far superior to the universal national standard of analytical reagent. Hence it could meet the requirements of high-purity, low-impurity for electroplating.%以硝酸铜与碳酸氢铵为原料,制备碱式碳酸铜,再经过高温焙烧,合成活性氧化铜粉.用X射线衍射(XRD)、含量测定、电感耦合等离子体原子发射光谱(ICP-AES)等方法对所得活性氧化铜粉末进行了表征.本方法合成的氧化铜纯度能达到99.3%以上,高于目前市场上的分析纯试剂标准,其它金属杂质也远远优于分析纯标准,达到了电镀用氧化铜高纯度、低杂质的要求.

  18. Distribution of angular momentum transfers from (p , d) and (p , t) reactions in the high excitation energy continuum region of gadolinium nuclei

    Science.gov (United States)

    Tarlow, Thomas; Beausang, Cornelius; Hughes, Richard; Ross, Timothy; Gell, Kristen; Vyas, Gargi

    2013-10-01

    The structure of even and odd Gd nuclei at low/moderate spins and up to high excitation energies in the vicinity of the N = 90 shape change region have been probed using the (p,t) and (p,d) reactions on even-even targets. The proton beam, at a beam energy of 25 MeV, was provided by the 88-Inch Cyclotron at Lawrence Berkeley National Laboratory. Outgoing charged particles, between ~30 and 60 degrees, were detected by the STARS silicon telescope while coincident gamma-rays were detected with the clover Ge detectors of the Liberace Array. The measured angular distributions for outgoing deuterons and tritons are well reproduced by DWBA calculations for discrete low-lying states, whereas at higher excitations of (2 - 9) MeV the angular momentum distribution of the continuum region should be represented by a distribution of L-transfer values. The angular distribution of the continuum region has been investigated in the present work . Weighted linear combinations of calculated (DWBA) angular distributions for L-transfer values of ΔL = 0 to 6 ℏ are compared to the experimental angular distribution in a chi-square minimization technique to find the best fitting distribution of angular momentum transfers in gadolinium nuclei. Preliminary results will be presented.

  19. Pulse electrosynthesis of novel wormlike gadolinium oxide nanostructure and its nanocomposite with conjugated electroactive polymer as a hybrid and high efficient electrode material for energy storage device.

    Science.gov (United States)

    Shiri, Hamid Mohammad; Ehsani, Ali

    2016-12-15

    An effective approach for increasing the life cycle of pure p-type conductive polymers is combining conventional conductive polymers and nanomaterials to fabricate hybrid electrodes. In this paper, Gadolinium oxide (Gd2O3) has first been synthesized using pulse electrochemical approach. Hybrid POAP/Gd2O3 films have then been fabricated by POAP electropolymerization in the presence of Gd2O3 nanoparticles as active electrodes for electrochemical supercapacitors. Surface and electrochemical analyses have been used for characterization of Gd2O3 and POAP/Gd2O3 composite films. Different electrochemical methods including galvanostatic charge discharge experiments, cyclic voltammetry and electrochemical impedance spectroscopy have been applied to study the system performance. Specific capacitance, specific energy and specific power of the composite film are calculated 300F·g(-1), 41.66Wh·kg(-1) and 833.22W·kg(-1) respectively. This work introduces new nanocomposite materials for electrochemical redox capacitors with such advantages as the ease of synthesis, high active surface area and stability in an aqueous electrolyte.

  20. Cyclotron production of high purity (44m,44)Sc with deuterons from (44)CaCO3 targets.

    Science.gov (United States)

    Alliot, C; Kerdjoudj, R; Michel, N; Haddad, F; Huclier-Markai, S

    2015-06-01

    Due to its longer half-life, (44)Sc (T1/2 = 3.97 h) as a positron emitter can be an interesting alternative to (68)Ga (T1/2 = 67.71 min). It has been already proposed as a PET radionuclide for scouting bone disease and is already available as a (44)Ti/(44)Sc generator. (44)Sc has an isomeric state, (44 m)Sc (T1/2 = 58.6 h), which can be co-produced with (44)Sc and that has been proved to be considered as an in-vivo PET generator (44 m)Sc/(44)Sc. This work presents the production route of (44 m)Sc/(44)Sc generator from (44)Ca(d,2n), its extraction/purification process and the evaluation of its performances. Irradiation was performed in a low activity target station using a deuteron beam of 16 MeV, which favors the number of (44 m)Sc atoms produced simultaneously to (44)Sc. Typical irradiation conditions were 60 min at 0.2 μA producing 44 MBq of (44)Sc with a (44)Sc/(44 m)Sc activity ratio of 50 at end of irradiation. Separations of the radionuclides were performed by means of cation exchange chromatography using a DGA® resin (Triskem). Then, the developed process was applied with bigger targets, and could be used for preclinical studies. The extraction/purification process leads to a radionucleidic purity higher than 99.99% ((43)Sc, (46)Sc, (48)Sc < DL). (44 m)Sc/(44)Sc labeling towards DOTA moiety was performed in order to get an evaluation of the specific activities that could be reached with regard to all metallic impurities from the resulting source. Reaction parameters of radiolabeling were optimized, reaching yields over 95%, and leading to a specific activity of about 10-20 MBq/nmol for DOTA. A recycling process for the enriched (44)Ca target was developed and optimized. The quality of the final batch with regard to radionucleidic purity, specific activity and metal impurities allowed a right away use for further radiopharmaceutical evaluation. This radionucleidic pair of (44 m)Sc/(44)Sc offers a quite interesting PET radionuclide for being further

  1. Determination of rare earth elements in high purity rare earth oxides by liquid chromatography, thermionic mass spectrometry and combined liquid chromatography/thermionic mass spectrometry

    Science.gov (United States)

    Stijfhoorn, D. E.; Stray, H.; Hjelmseth, H.

    1993-03-01

    A high-performance liquid Chromatographie (HPLC) method for the determination of rare earth elements in rocks has been modified and used for the determination of rare earth elements (REE) in high purity rare earth oxides. The detection limit was 1-1.5 ng or 2-3 mg/kg when a solution corresponding to 0.5 mg of the rare earth oxide was injected. The REE determination was also carried out by adding a mixture of selected REE isotopes to the sample and analysing the collected HPLC-fractions by mass spectrometry (MS) using a thermionic source. Since the matrix element was not collected, interference from this element during the mass spectrometric analysis was avoided. Detection limits as low as 0.5 mg/kg could then be obtained. Detection limits as low as 0.05 mg/kg were possible by MS without HPLC-pre-separation, but this approach could only be used for those elements that were not affected by the matrix. Commercial samples of high purity Nd 2O 3, Gd 2O 3 and Dy 2O 3 were analysed in this study, and a comparison of results obtained by HPLC, combined HPLC/MS and direct MS are presented.

  2. Obtention of high purity silica from the flotation waste of itabiritic ore; Obtencao de silica de elevada pureza a partir do rejeito de flotacao de um minerio itabiritico

    Energy Technology Data Exchange (ETDEWEB)

    Martins, Polyana Fabricia Fernandes

    2016-10-01

    Banded iron formations are exploited as iron mineral in 'Quadrilatero Ferrifero' of Minas Gerais (MG) State, Brazil. About half of the amount of extracted material becomes tailings, which are stored in tailing dams or used for filling mining pits. Tens of thousands of tons are generated daily in operating mines in this region, causing concern about the environmental liabilities, and costs to manage the tailing dams. Miners are committed to finding uses for these wastes in other productive chains. This thesis aimed to obtain high purity silica from the flotation tailings of banded iron formations using classical techniques for ore processing, such as particle size classification and magnetic separation, followed by hydrometallurgical leaching, also alkaline fusion and chemical precipitation. The tailings samples was collected in the tailings dam of Peak Mine operated by Vale A.S., in Itabirito – MG. This sample had initially 33.4% by weight SiO{sub 2}, 57.4% wt Fe{sub 2}O{sub 3} and 8.31% wt Al{sub 2}O{sub 3}. After desliming for disposal of the fine particles (-37μm) the composition was 68.0% SiO{sub 2}, 31.4% Fe{sub 2}O{sub 3} and 0.50% Al{sub 2}O{sub 3}. After magnetic separation, the composition was 93.8% SiO{sub 2}, 1.16% Fe{sub 2}O{sub 3} and 3.80% Al{sub 2}O{sub 3}. After acid leaching l or digestion to remove impurities, it was possible to obtain silica with 98% purity. The fusion with sodium hydroxide, followed by alkaline leaching of sodium silicate and silica precipitation gave purities of about 99.5%. Values even higher may be possible with optimization of the parameters of alkaline fusion or by repeating the process from the product with purity of 99.5%. The iron oxide content and the aluminum main contaminants were 0.01% and 0.07%, respectively. Amorphous silica was obtained with high specific surface (322 m{sup 2}/g) and particle size less than 200 nm. Depending on the application, a control should be made for the impurities, such as

  3. Characterization of gadolinium and lanthanum oxide films on Si (100)

    Science.gov (United States)

    Wu, X.; Landheer, D.; Sproule, G. I.; Quance, T.; Graham, M. J.; Botton, G. A.

    2002-05-01

    High-resolution transmission electron microscopy, electron energy loss spectroscopy, and Auger electron spectroscopy, were used to study gadolinium and lanthanum oxide films deposited on Si (100) substrates using electron-beam evaporation from pressed-powder targets. As-deposited films consist of a crystalline oxide layer and an amorphous interfacial layer. A complicated distinct multilayer structure consisting of oxide layers, silicate layers, and SiO2-rich layers in thick (~30 nm) annealed films has been observed for both gadolinium and lanthanum films. For thinner annealed films (~8 nm), there is no longer a crystalline oxide layer but an amorphous gadolinium or lanthanum silicate layer and an interfacial SiO2-rich layer. The formation of the lanthanum silicate by annealing lanthanum oxide is found to be thermodynamically more favorable than the formation of gadolinium silicate.

  4. Dynamical recrystallization of high purity austenitic stainless steels; Recristallisation dynamique d'aciers inoxydables austenitiques de haute purete

    Energy Technology Data Exchange (ETDEWEB)

    Gavard, L

    2001-01-01

    The aim of this work is to optimize the performance of structural materials. The elementary mechanisms (strain hardening and dynamical regeneration, germination and growth of new grains) occurring during the hot working of metals and low pile defect energy alloys have been studied for austenitic stainless steels. In particular, the influence of the main experimental parameters (temperature, deformation velocity, initial grain size, impurities amount, deformation way) on the process of discontinuous dynamical recrystallization has been studied. Alloys with composition equal to those of the industrial stainless steel-304L have been fabricated from ultra-pure iron, chromium and nickel. Tests carried out in hot compression and torsion in order to cover a wide range of deformations, deformation velocities and temperatures for two very different deformation ways have allowed to determine the rheological characteristics (sensitivity to the deformation velocity, apparent activation energy) of materials as well as to characterize their microstructural deformations by optical metallography and electron back-scattered diffraction. The influence of the initial grain size and the influence of the purity of the material on the dynamical recrystallization kinetics have been determined. An analytical model for the determination of the apparent mobility of grain boundaries, a semi-analytical model for the dynamical recrystallization and at last an analytical model for the stationary state of dynamical recrystallization are proposed as well as a new criteria for the transition between the refinement state and the state of grain growth. (O.M.)

  5. An efficient method for high-purity anthocyanin isomers isolation from wild blueberries and their radical scavenging activity.

    Science.gov (United States)

    Chorfa, Nasima; Savard, Sylvain; Belkacemi, Khaled

    2016-04-15

    An efficient process for the purification of anthocyanin monomeric isomers from wild blueberries of Lake Saint-Jean region (Quebec, Canada) was developed and easy scalable at industrial purpose. The blueberries were soaked in acidified ethanol, filtered, and the filtrate was cleaned by solid phase extraction using silica gel C-18 and DSC-SCX cation-exchange resin. Anthocyanin-enriched elutes (87 wt.%) were successfully fractionated by preparative liquid chromatography. The major anthocyanins mono-galactoside, -glucoside and -arabinoside isomers of delphinidin, cyanidin, petunidin, peonidin and malvidin were isolated with a purity up to 100% according to their LC-MS and (1)H NMR spectra. The oxygen radical absorbance capacity (ORAC) of the obtained pure anthocyanins was evaluated. Delphinidin-3-galactoside has the highest capacity (13.062 ± 2.729 μmol TE/μmol), and malvidin-3-glucoside the lowest (0.851 ± 0.032 μmol TE/μmol). A mechanistic pathway preview is suggested for the anthocyanins scavenging free radical activity by hydrogen transfer.

  6. Direct Determination of Trace Impurities in High Purity Neodymium after In-Situ Analyte-Matrix Separation by Fluorination Assisted ETV-ICP-AES

    Institute of Scientific and Technical Information of China (English)

    Ruth Wanjau; Hu Bin(胡斌); He Man(何蔓); Jiang Zucheng(江祖成); Wu Yingliang(吴英亮)

    2004-01-01

    Using PTFE as a chemical modifier, a method for the determination of trace impurities in high purity Nd2O3 by in-situ separation and electrothermal vaporization-inductively coupled plasma-atomic emission spectrometry (ETV-ICP-AES) was developed. The analyte-matrix separation and the temperature program of graphite furnace were investigated and optimized. The solid samples were directly introduced into graphite furnace in the form of slurry, where selective volatilization between the matrix and the analytes took place. The Nd matrix was retained in the graphite furnace during the evaporation step, while the trace analyte impurities were vaporized and removed. As a result, the matrix interference that is serious without the modifier is suppressed effectively. The achievable detection limits are (μg·g-1): Ti 0.15, Mn 0.15, Ni 0.20, Co 0.54, respectively. The proposed method was applied to direct determination of trace impurities in high purity Nd2O3 with satisfactory results.

  7. Jerusalem artichoke powder: a useful material in producing high-optical-purity l-lactate using an efficient sugar-utilizing thermophilic Bacillus coagulans strain.

    Science.gov (United States)

    Wang, Limin; Xue, Zhangwei; Zhao, Bo; Yu, Bo; Xu, Ping; Ma, Yanhe

    2013-02-01

    Jerusalem artichoke is a low-requirement crop, which does not interfere with food chain, and is a promising carbon source for industrial fermentation. Microbial conversion of such a renewable raw material to useful products, such as lactic acid, is an important objective in industrial biotechnology. In this study, high-optical-purity l-lactate was efficiently produced from the hydrolysates of Jerusalem artichoke powder by a thermophilic bacterium, Bacillus coagulans XZL4. High l-lactate production (134gl(-1)) was obtained using 267gl(-1) Jerusalem artichoke powder (total reducing sugars of 140gl(-1)) and 10gl(-1) of corn steep powder in fed-batch fermentation, with an average productivity of 2.5gl(-1)h(-1) and a yield of 0.96gg(-1) reducing sugars. The final product optical purity is 99%, which meets the requirement of lactic acid polymerization. Our study represents a cost-effective and promising method for polymer-grade l-lactate production using a cheap raw bio-resource. Copyright © 2012 Elsevier Ltd. All rights reserved.

  8. Study on the Production Process for High Purity Natural Anethole%高纯度天然大茴香脑生产技术研究

    Institute of Scientific and Technical Information of China (English)

    李超群; 蒋天成

    2013-01-01

    The high purity natural anethole (>99%) was obtained by using natural star anise oil as raw material via static freezing, centrifugation and rectification employing fractionation tower filled with stainless steel wave filler. The quality of product was assessed following the standard of GB 23489—2009. The results showed that this process was simple and practical, which could be used as a novel method for producing high purity natural anethole.%以八角茴香油为原料,采用静态冷冻工艺冷冻、离心制备得到粗产品,再采用网波不锈钢填料分馏塔对粗产品进行精馏分离得到高纯度大茴香脑(纯度>99%).产品按国家标准GB 23489-2009的要求进行检验.此工艺路线简单、实用,产品品质优良,是生产高纯度天然大茴香脑的新型实用方法.

  9. A novel high color purity blue-emitting phosphor: CaBi{sub 2}B{sub 2}O{sub 7}:Tm{sup 3+}

    Energy Technology Data Exchange (ETDEWEB)

    Li, Jiangong, E-mail: lijiangong01@gmail.com [Department of Electronic Science and Engineering, Huanghuai University, Zhumadian 463000 (China); Yan, Huifang [Department of Foreign Languages and Literature, Huanghuai University, Zhumadian 463000 (China); Yan, Fengmei [Department of Chemistry and Chemical Engineering, Huanghuai University, Zhumadian 463000 (China)

    2016-07-15

    Graphical abstract: - Highlights: • A series of Tm{sup 3+}-doped CaBi{sub 2}B{sub 2}O{sub 7} blue-emitting phosphors were prepared. • The optimum doping content of Tm{sup 3+} ions was found. • The critical distance and concentration quenching mechanism was discussed. • The color purity of as prepared sample was analyzed and compared. - Abstract: A series of Tm{sup 3+}-doped CaBi{sub 2−x}B{sub 2}O{sub 7}:xTm{sup 3+} (0.02 ≤ x ≤ 0.12) blue-emitting phosphors with high color purity were prepared by solid-state reaction method. The crystal structure and luminescence properties of the as-prepared phosphors were studied. This phosphor shows a satisfactory blue performance (peak at 453 nm) due to the {sup 1}D{sub 2} → {sup 3}F{sub 4} transition of Tm{sup 3+} excited by 357 nm light. Investigation of Tm{sup 3+} content dependent emission spectra indicates that x = 0.04 is the optimum doping content of Tm{sup 3+} ions in the CaBi{sub 2}B{sub 2}O{sub 7} host. The critical distance and the concentration quenching mechanism were also investigated. In particular, the color purity of as prepared sample was analyzed and the result shows that the color purity of CaBi{sub 2}B{sub 2}O{sub 7}:Tm{sup 3+} is higher than the commercial blue phosphor BaMgAl{sub 10}O{sub 17}:Eu{sup 2+} (BAM:Eu{sup 2+}) and the latest reported Tm{sup 3+} doped blue phosphors. The present work suggests that the CaBi{sub 2}B{sub 2}O{sub 7}:Tm{sup 3+} phosphor is a potential blue-emitting candidate for the application in the near-UV WLEDs.

  10. 碳化法制备高纯碳酸锂%Preparation of high purity lithium carbonate by carbonization method

    Institute of Scientific and Technical Information of China (English)

    周启立; 王莫飞

    2012-01-01

    Carbonization method was adopted for purification of industrial lithium carbonate.The key influencing factors, such as carbonization temperature,carbonization time,and carbonization pressure,were experimentally studied and analyzed. The optimum reaction conditions were confirmed as follows:carbonization pressure was 6xl0i~6.5xl05 Pa,carbonization time was 2-3 h, carbonization temperature was 30-40 X., brand of resin was Dl 10,flow rate of mother liquor was 120-140 g/h,and mixing speed was over 30 r/s.Under such conditions the purity of prepared lithium carbonate could reach 99.991%.%以工业级碳酸锂为原料,采用碳化法进行提纯,对碳化温度、碳化时间、碳化压力等重要影响因素进行了实验研究及分析,并确定了最佳反应条件.最佳工艺参数:碳化压力为6× 105~6.5× 105 Pa,碳化时间为2~3 h,碳化温度为30~40℃,树脂牌号为D110,母液流出速度为120~140g/h,分解搅拌速度为30r/s以上,此工艺条件下制得的碳酸锂纯度为99.991%.

  11. High temperature annealing effects on deep-level defects in a high purity semi-insulating 4H-SiC substrate

    Science.gov (United States)

    Iwamoto, Naoya; Azarov, Alexander; Ohshima, Takeshi; Moe, Anne Marie M.; Svensson, Bengt G.

    2015-07-01

    Effects of high-temperature annealing on deep-level defects in a high-purity semi-insulating 4H silicon carbide substrate have been studied by employing current-voltage, capacitance-voltage, junction spectroscopy, and chemical impurity analysis measurements. Secondary ion mass spectrometry data reveal that the substrate contains boron with concentration in the mid 1015 cm-3 range, while other impurities including nitrogen, aluminum, titanium, vanadium and chromium are below their detection limits (typically ˜1014 cm-3). Schottky barrier diodes fabricated on substrates annealed at 1400-1700 °C exhibit metal/p-type semiconductor behavior with a current rectification of up to 8 orders of magnitude at bias voltages of ±3 V. With increasing annealing temperature, the series resistance of the Schottky barrier diodes decreases, and the net acceptor concentration in the substrates increases approaching the chemical boron content. Admittance spectroscopy results unveil the presence of shallow boron acceptors and deep-level defects with levels in lower half of the bandgap. After the 1400 °C annealing, the boron acceptor still remains strongly compensated at room temperature by deep donor-like levels located close to mid-gap. However, the latter decrease in concentration with increasing annealing temperature and after 1700 °C, the boron acceptor is essentially uncompensated. Hence, the deep donors are decisive for the semi-insulating properties of the substrates, and their thermal evolution limits the thermal budget for device processing. The origin of the deep donors is not well-established, but substantial evidence supporting an assignment to carbon vacancies is presented.

  12. High temperature annealing effects on deep-level defects in a high purity semi-insulating 4H-SiC substrate

    Energy Technology Data Exchange (ETDEWEB)

    Iwamoto, Naoya, E-mail: naoya.iwamoto@smn.uio.no; Azarov, Alexander; Svensson, Bengt G. [Department of Physics, Center for Materials Science and Nanotechnology, University of Oslo, P.O. Box 1048 Blindern, N-0316 Oslo (Norway); Ohshima, Takeshi [Japan Atomic Energy Agency, 1233 Watanuki, Takasaki, 370-1292 Gunma (Japan); Moe, Anne Marie M. [Washington Mills AS, N-7300 Orkanger (Norway)

    2015-07-28

    Effects of high-temperature annealing on deep-level defects in a high-purity semi-insulating 4H silicon carbide substrate have been studied by employing current-voltage, capacitance-voltage, junction spectroscopy, and chemical impurity analysis measurements. Secondary ion mass spectrometry data reveal that the substrate contains boron with concentration in the mid 10{sup 15 }cm{sup −3} range, while other impurities including nitrogen, aluminum, titanium, vanadium and chromium are below their detection limits (typically ∼10{sup 14 }cm{sup −3}). Schottky barrier diodes fabricated on substrates annealed at 1400–1700 °C exhibit metal/p-type semiconductor behavior with a current rectification of up to 8 orders of magnitude at bias voltages of ±3 V. With increasing annealing temperature, the series resistance of the Schottky barrier diodes decreases, and the net acceptor concentration in the substrates increases approaching the chemical boron content. Admittance spectroscopy results unveil the presence of shallow boron acceptors and deep-level defects with levels in lower half of the bandgap. After the 1400 °C annealing, the boron acceptor still remains strongly compensated at room temperature by deep donor-like levels located close to mid-gap. However, the latter decrease in concentration with increasing annealing temperature and after 1700 °C, the boron acceptor is essentially uncompensated. Hence, the deep donors are decisive for the semi-insulating properties of the substrates, and their thermal evolution limits the thermal budget for device processing. The origin of the deep donors is not well-established, but substantial evidence supporting an assignment to carbon vacancies is presented.

  13. High performance liquid chromatography with photo diode array for separation and analysis of naproxen and esomeprazole in presence of their chiral impurities: Enantiomeric purity determination in tablets.

    Science.gov (United States)

    Ragab, Marwa A A; El-Kimary, Eman I

    2017-05-12

    A stereoselective high performance liquid chromatographic method with diode array detection (HPLC-DAD) was introduced for S-naproxen and esomeprazole determination in tablets. The separation was achieved on a Kromasil Cellucoat chiral column using a mobile phase consisting of hexane: isopropanol: trifluoroacetic acid (TFA) (90:9.9:0.1 v/v/v). The proposed system was found to be suitable for the enantioseparation of naproxen and omeprazole biologically active isomers. After optimization of the chromatographic conditions, resolution values of 3.84 and 2.17 could be obtained for naproxen and omeprazole isomers, respectively. The method was fully validated for the determination of S-isomers of each drug in their dosage form. Also, the enentiomeric purity was determined in commercial tablet containing S-naproxen and esomeprazole. The enantiomeric purity was calculated for each drug and the chiral impurities (R-isomers) could be determined at 1% level. The method was validated and good results with respect to linearity, precision, accuracy, selectivity and robustness were obtained. The limits of detection (LOD) and quantification (LOQ) were 2.00, 6.50 and 0.10, 0.35μgmL(-1) for S-naproxen and esomeprazole, respectively. Copyright © 2017 Elsevier B.V. All rights reserved.

  14. 氧化镁铵盐法制备高纯过氧化镁%Preparation of High Purity Magnesium Peroxide by Magnesia and Ammonium Salt Solutions

    Institute of Scientific and Technical Information of China (English)

    朱海丽; 吴小王

    2011-01-01

    在氯化铵溶液体系中,以氧化镁,过氧化氢为原料,制备高纯过氧化镁。研究表明采用氧化镁活性大于100,氯化铵/氧化镁不小于10%,过氧化氢:氧化镁不小于4∶1,反应温度大于40℃情况下,反应时间不小于30 min,可制备出纯度大于90%的过氧化镁。%In ammonium chloride solution,magnesium oxide and hydrogen peroxide as raw material,high purity magnesium peroxide was prepared.The results showed that using magnesium oxide activity was greater than 100,ammonium chloride and magnesium oxide was not less than 10%,hydrogen peroxide to magnesium oxide was not less than 4:1,the reaction temperature was higher than 40 ℃,and the reaction time was not less than 30 min,with magnesium peroxide purity above 90%.

  15. Separation of high-purity syringol and acetosyringone from rice straw-derived bio-oil by combining the basification-acidification process and column chromatography.

    Science.gov (United States)

    Hao, Shilai; Chen, Kaifei; Cao, Leichang; Zhu, Xiangdong; Luo, Gang; Zhang, Shicheng; Chen, Jianmin

    2016-10-01

    Numerous technologies have been used to reclaim valuable chemicals from bio-oil. In this study, a combination of the basification-acidification process and column chromatography was employed for the separation of high-purity syringol and acetosyringone from rice straw-derived bio-oil. The optimal conditions for the basification-acidification process and the possible precipitation mechanism of the basification were explored. The results showed the following as the optimal conditions for the basification process: mass ratio of calcium hydroxide (Ca(OH)2 ) to bio-oil, 2.0; reaction temperature, 70°C; and reaction time, 30 min. The results also showed that 1.6 mol of hydrochloric acid (HCl) per gram of bio-oil was optimal for the acidification. The precipitation was found to proceed via a possible mechanism involving the reaction of the phenolic compounds in the bio-oil with Ca(OH)2 to produce a precipitate. After further separation by column chromatography, purities of 91.4 and 96.2% (from gas chromatography-mass spectrometry) were obtained for syringol and acetosyringone, respectively. Their recoveries for the whole process were 73.0 and 39.3%, respectively.

  16. Efficient out-coupling of high-purity single photons from a coherent quantum dot in a photonic-crystal cavity

    DEFF Research Database (Denmark)

    Madsen, Kristian Høeg; Ates, Serkan; Liu, J.

    2014-01-01

    We demonstrate a single-photon collection efficiency of (44.3 ± 2.1)% from a quantum dot in a low-Q mode of a photonic-crystal cavity with a single-photon purity of g(2)(0) = (4 ± 5)% recorded above the saturation power. The high efficiency is directly confirmed by detecting up to 962 ± 46...... kilocounts per second on a single-photon detector on another quantum dot coupled to the cavity mode. The high collection efficiency is found to be broadband, as is explained by detailed numerical simulations. Cavity-enhanced efficient excitation of quantum dots is obtained through phonon-mediated excitation...... and under these conditions, single-photon indistinguishability measurements reveal long coherence times reaching 0.77 ± 0.19 ns in a weak-excitation regime. Our work demonstrates that photonic crystals provide a very promising platform for highly integrated generation of coherent single photons including...

  17. Intense red-emitting Y4Al2O9:Eu3+ phosphor with short decay time and high color purity for advanced plasma display panel

    National Research Council Canada - National Science Library

    Yadav, Ravishanker; Khan, Atif F; Yadav, Ashish; Chander, Harish; Haranath, Divi; Gupta, Bipin Kr; Shanker, Virendra; Chawla, Santa

    2009-01-01

    ...) excitations has been developed for application in next generation plasma display panels (PDPs). The developed phosphor has better luminescence efficiency, colour purity and shorter decay time than commercial...

  18. Effect Of The Gadolinium Oxide Addition On The Electrical Properties Of Tetragonal Zirconium Dioxide

    Directory of Open Access Journals (Sweden)

    Cyran J.

    2015-06-01

    Full Text Available The aim of this work was examination of gadolinium-doped 3YSZ electrical and structural properties. Such materials may be used as electrolytes in intermediate temperature solid oxide fuel cells (IT-SOFC. First step of the research was synthesis of 3YSZ with different contents of gadolinium (0.25; 0.5; 1.0 at %. Prepared materials were characterized by high porosity. No effect of gadolinium addition on grain size was observed. The experimentally determined values of grain interiors electrical conductivities for gadolinium doped samples are comparable to grain interior conductivities of gadolinium free tetragonal zirconia. On the other hand, a clear effect of gadolinium addition on electrical conductivity of grain boundaries was observed. It was found that 3YSZ containing 0.25 at. % Gd was the most promising from the investigated materials as a solid electrolyte for IT SOFC.

  19. Efficient out-coupling of high-purity single photons from a coherent quantum dot in a photonic-crystal cavity

    CERN Document Server

    Madsen, K H; Liu, J; Javadi, A; Albrecht, S M; Yeo, I; Stobbe, S; Lodahl, P

    2014-01-01

    We demonstrate a single-photon collection efficiency of $(44.3\\pm2.1)\\%$ from a quantum dot in a low-Q mode of a photonic-crystal cavity with a single-photon purity of $g^{(2)}(0)=(4\\pm5)\\%$ and directly detect up to $962\\pm46$ kilocounts per second on a single-photon detector. The high collection efficiency is found to be broadband, as is confirmed by detailed numerical simulations. Cavity-enhanced efficient excitation of quantum dots is obtained through phonon-mediated excitation and under these conditions, single-photon indistinguishability measurements reveal long coherence times of up to $0.77\\pm0.19$ ns. Our work demonstrates that photonic crystals provide a very promising platform for highly integrated generation of coherent single photons including the efficient outcoupling of the photons from the photonic chip.

  20. Performance comparison of AlTiC and AlTiB master alloys in grain refinement of commercial and high purity aluminum

    Institute of Scientific and Technical Information of China (English)

    LI Jian-guo; HUANG Min; MA Mo; YE Wei; LIU Dong-yu; SONG Dong-ming; BAI Bing-zhe; FANG Hong-sheng

    2006-01-01

    For further knowledge about the refining performance of AlTiC master alloys, Al5.5Ti0.25C and Al6.5Ti0.5C master alloys containing high Ti and C content were prepared and used in grain refining experiments of 99.8% commercial pure aluminum(CPAl). Their performance was compared with two types of Al5TilB refiners whose performance was nowadays considered to be the best. These two types of master alloys show similar refining efficiency at the addition level of 0.2%. However, at the addition level of 0.5%, there still exists great performance difference between AlTiC and Al5TiB alloys in grain refinement of 99.98% and 99.995% high purity aluminum(HPAl). The growth of columnar grains is fully suppressed due to the refinement of AlTiC at the addition level of 0.5%. Also, at the same addition level, the grain refining experiments of Al3Ti0.15C and Al5Ti0.2C master alloys which have found initial commercial applications are conducted in the above-mentioned three types of pure aluminum.According to the experimental results, these two refiners of different compositions are both nonideal. The second phase particles extracted from each refiner were observed through TEM, while the nuclei of grains after grain refinement were observed through SEM. The results were analyzed through computation and comparison of the constitutional-supercooling parameter and the growth-restriction parameter whose values were determined by solute element in aluminum melt with different purity. Apparently,AlTiC master alloys with high content of Ti and C element have great refining potential.

  1. Removal of an iron matrix with polyoxyethylene-type surfactant-coated amberlite XAD-4 for the determination of trace impurities in high-purity iron.

    Science.gov (United States)

    Matsumiya, Hiroaki; Furuzawa, Shigeru; Hiraide, Masataka

    2005-08-15

    Admicellar sorbents for the removal of an iron matrix were prepared for the determination of trace impurities in high-purity iron. A 1.0-g amount of Amberlite XAD-4 (macroreticular styrene-divinylbenzene copolymer) was coated with 0.14-1.3 mmol of polyoxyethylene-type surfactants, including polyoxyethylene-4-tert-octylphenoxy ethers (Triton X series) and polyoxyethylene-4-isononylphenoxy ethers (PONPEs). The surfactant-coated XAD-4 was packed into a polypropylene column (7 mm i.d. x 50 mm high). A 5.0-cm(3) volume of sample solution was passed through the column at a flow rate of 0.5 cm(3) min(-1). Milligram amounts of iron(III) were effectively sorbed on the column from 8 mol dm(-3) hydrochloric acid solutions. Among the surfactants tested, polyoxyethylene(20)-4-isononylphenoxy ether (PONPE-20) showed the best performance: the iron leaked from the PONPE-20 column was 4 microg when 25 mg of iron(III) was introduced onto the column. Trace elements, such as Ti(IV), Cr(III), Mn(II), Co(II), Ni(II), Cu(II), Zn(II), Ag(I), Cd(II), Pb(II), and Bi(III), were not retained on the column and thus quantitatively recovered in the column effluent. The effective separation of trace elements from an iron matrix allowed their accurate determinations by inductively coupled plasma-mass spectrometry or graphite furnace atomic absorption spectrometry. The detection limits (3sigma blank) were in the nanogram per gram range. The proposed method was successfully applied to the determination of trace impurities in high-purity iron samples.

  2. Un método reproducible para obtener peg biramificado monofuncional de alta pureza A reproducible method for obtaining a 2-arms monofunctional peg with high purity

    Directory of Open Access Journals (Sweden)

    José A. Ramón

    2009-01-01

    Full Text Available PEGylation has become a widely applied technique to enhancing in vitro and in vivo stability of therapeutic proteins and to increasing materials biocompatibility. PEG branched structures have proven useful for protein and peptide modification. Furthermore, they may be better than linear structures for many purposes. This paper describes an improved procedure for obtaining 2-arms PEG based on L-lysine. The efficiency of the synthesis was not related to moisture of the raw materials. This procedure does not use hazardous reagents as previous protocols do. It implemented a purification process for obtaining the desired structure with high purity ( > 99%. Finally, the procedure described here allows the obtaining of others PEGylation reagents.

  3. Possible influence of surface oxides on the optical response of high-purity niobium material used in the fabrication of superconducting radio frequency cavity

    Science.gov (United States)

    Singh, Nageshwar; Deo, M. N.; Roy, S. B.

    2016-09-01

    We have investigated the possible influence of surface oxides on the optical properties of a high-purity niobium (Nb) material for fabrication of superconducting radio frequency (SCRF) cavities. Various peaks in the infrared region were identified using Fourier transform infrared and Raman spectroscopy. Optical response functions such as complex refractive index, dielectric and conductivity of niobium were compared with the existing results on oxides free Nb and Cu. It was observed that the presence of a mixture of niobium-oxides, and probably near other surface impurities, appreciably influence the conducting properties of the material causing deviation from the typical metallic characteristics. In this way, the key result of this work is the observation, identification of vibrational modes of some of surface complexes and study of its influences on the optical responses of materials. This method of spectroscopic investigation will help in understanding the origin of degradation of performance of SCRF cavities.

  4. Possible influence of surface oxides on the optical response of high-purity niobium material used in the fabrication of superconducting radio frequency cavity

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Nageshwar [Magnetic and Superconducting Materials Section, Raja Ramanna Centre for Advanced Technology, Indore 452013, M.P. (India); Deo, M.N. [High Pressure & Synchrotron Radiation Physics Division, BARC, Mumbai 400085 (India); Roy, S.B. [Magnetic and Superconducting Materials Section, Raja Ramanna Centre for Advanced Technology, Indore 452013, M.P. (India)

    2016-09-11

    We have investigated the possible influence of surface oxides on the optical properties of a high-purity niobium (Nb) material for fabrication of superconducting radio frequency (SCRF) cavities. Various peaks in the infrared region were identified using Fourier transform infrared and Raman spectroscopy. Optical response functions such as complex refractive index, dielectric and conductivity of niobium were compared with the existing results on oxides free Nb and Cu. It was observed that the presence of a mixture of niobium-oxides, and probably near other surface impurities, appreciably influence the conducting properties of the material causing deviation from the typical metallic characteristics. In this way, the key result of this work is the observation, identification of vibrational modes of some of surface complexes and study of its influences on the optical responses of materials. This method of spectroscopic investigation will help in understanding the origin of degradation of performance of SCRF cavities.

  5. Internal friction of very high purity lead (99,9999%) at medium temperatures; Friccion interna en plomo de muy alta pureza (99,9999%) a temperaturas medias

    Energy Technology Data Exchange (ETDEWEB)

    Gallego, I.; Gutierrez-Urrutia, I.; San Juan, J. M.; No, M. L.

    2001-07-01

    Internal friction spectra of high purity lead (99,9999%) at medium temperatures exhibit a main relaxation peak at 230 K (P{sub 1}) which depends strongly on the dislocation arrangement. The mechanisms associated to P{sub 1} relaxation has an activation area between 500b2 and 2000b 2 and its activation energy is 0.65{+-}0.05 eV 863{+-}5KJ/mol, which is only 0.6 times the auto diffusion energy of lead. The behaviour of P{sub 1} peak and its dependence on thermomechanical treatments has allowed us to conclude that it is associated to the sliding of dislocations controlled by the climbing of jogs by diffusion of vacancies along the dislocation lines. At a slightly higher temperature, another relaxation (P{sub 1}) turns up in the spectra, which can be associated to different mechanisms. (Author) 12 refs.

  6. 高纯乙腈连续精馏过程建模与分析%Modeling and analyzing of continuous process for rectifying high purity acetonitrile

    Institute of Scientific and Technical Information of China (English)

    曾涵卫; 孙小方; 蔡亦军; 夏陆岳; 周猛飞; 潘海天

    2012-01-01

    Based on the deep analysis of continuous process of rectifying high purity acetonitrile and its mechanics, with rational assumptions dynamic mathematical models of multi - tower for rectifying high purity acetonitrile were established by material balance, energy balance, environmental impact and hydraulic analysis, considering the character of multi-stage cascade and the difficulty of operating conditions optimization. Furthermore, the dynamic simulation and analysis were carried out respectively to the dealcoholization tower, vacuum tower and pressure tower. Simultaneously, investigating the tower pressure and steam heating effect on the separation process, and finding the further relative dynamic data of acetonitrile could provide a good foundation for the research of system integration optimization and control.%针对高纯乙腈连续精馏过程多塔串级及操作条件优化困难等特点,在深入分析乙腈连续精馏工艺流程及机理基础上,通过物料衡算、能量衡算、环境影响衡算和水力学分析等原理,结合必要的合理假设,建立乙腈连续精馏多塔的动态数学模型,对脱醇塔、减压塔和加压塔分别进行动态模拟和分析,考察塔内压力、加热蒸汽量等对分离过程的影响,并进一步寻找这些因素对出料乙腈的动态变化数据,为实施系统的集成优化与控制提供了良好基础.

  7. Monte Carlo simulation of gamma-ray interactions in an over-square high-purity germanium detector for in-vivo measurements

    Science.gov (United States)

    Saizu, Mirela Angela

    2016-09-01

    The developments of high-purity germanium detectors match very well the requirements of the in-vivo human body measurements regarding the gamma energy ranges of the radionuclides intended to be measured, the shape of the extended radioactive sources, and the measurement geometries. The Whole Body Counter (WBC) from IFIN-HH is based on an “over-square” high-purity germanium detector (HPGe) to perform accurate measurements of the incorporated radionuclides emitting X and gamma rays in the energy range of 10 keV-1500 keV, under conditions of good shielding, suitable collimation, and calibration. As an alternative to the experimental efficiency calibration method consisting of using reference calibration sources with gamma energy lines that cover all the considered energy range, it is proposed to use the Monte Carlo method for the efficiency calibration of the WBC using the radiation transport code MCNP5. The HPGe detector was modelled and the gamma energy lines of 241Am, 57Co, 133Ba, 137Cs, 60Co, and 152Eu were simulated in order to obtain the virtual efficiency calibration curve of the WBC. The Monte Carlo method was validated by comparing the simulated results with the experimental measurements using point-like sources. For their optimum matching, the impact of the variation of the front dead layer thickness and of the detector photon absorbing layers materials on the HPGe detector efficiency was studied, and the detector’s model was refined. In order to perform the WBC efficiency calibration for realistic people monitoring, more numerical calculations were generated simulating extended sources of specific shape according to the standard man characteristics.

  8. Preparation of High Purity V2O5 from a Typical Low-Grade Refractory Stone Coal Using a Pyro-Hydrometallurgical Process

    Directory of Open Access Journals (Sweden)

    Xiao Yang

    2016-07-01

    Full Text Available The recovery of vanadium from a typical low-grade refractory stone coal was investigated using a pyro-hydrometallurgical process specifically including blank roasting, acid leaching, solvent extraction, and chemical precipitation. The appropriate role of parameters in each process was analyzed in detail. Roasting temperature and roasting time during the roasting process showed a significant effect on leaching efficiency of vanadium. Using H2SO4 as a leaching agent, vanadium leaching efficiency can achieve above 90% under the optimum leaching conditions of CaF2 dosage of 5%, sulfuric acid concentration of 4 mol/L, liquid to solid ratio of 2:1 mL/g, leaching time of 2 h, and leaching temperature of 95 °C. 99.10% of vanadium can be extracted from the leaching solution in three stages under the conditions of initial pH of 1.6, trioctylamine (TOA extractant concentration of 20% (vol, phase ratio (A/O of 2, and reaction time of 2 min. 1.0 mol/L NaOH was used to strip vanadium from the extracted solvent phase. After purification and precipitation, vanadium can be crystallized as ammonium metavanadate. The V2O5 product with a purity of 99.75% is obtained after ammonium metavanadate thermal decomposition at 550 °C for 2 h. The total vanadium recovery in the whole process is above 88%. This process has advantages of short operation time, high vanadium extraction efficiency, and high purity of the product.

  9. MR imaging in recurrent pain after back surgery. A comparative study using standard and high doses of gadolinium contrast agents

    Energy Technology Data Exchange (ETDEWEB)

    Aakeson, P. [Univ. Hospital, Lund (Sweden). Dept. of Radiology; Annertz, M. [Univ. Hospital, Lund (Sweden). Dept. of Radiology; Kristoffersen, D.T. [Nycomed Imaging AS, Oslo (Norway); Jonsson, E. [Nycomed AB, Stockholm (Sweden); Holtaas, S. [Univ. Hospital, Lund (Sweden). Dept. of Radiology

    1996-11-01

    Purpose: To compare the diagnostic results following injection of (a) a high dose (0.3 mmol/kg b.w.) of gadodiamide injection and (b) the standard dose (0.1 mmol/kg b.w.) of Gd-DTPA, in patients with recurrent symptoms after surgery for lumbar disc herniation. Material and Methods: Twenty patients with recurrent or sustained symptoms after surgery for lumbar disc herniations were examined. MR imaging (0.3 T) was first performed before and after Gd-DTPA at 0.1 mmol/kg b.w., and then within one month (17 patients) or within 3 months (3 patients) before and after gadodiamide injection at 0.3 mmol/kg b.w. The examinations were first evaluated by 2 neuroradiologists blinded to dose but not to patient as the images were presented in pairs. Six months later the same investigators evaluated the examinations again, this time blinded to both dose and patient. Results: At the evaluation in pairs (with the investigators blinded to dose only) the high-dose examinations were considered the most informative (p=0.05). However, at the later evaluation (with the investigators blinded both to dose and patient) no significant difference between high and standard dose was found regarding diagnosis or diagnostic certainty. Conclusion: In this study the high-dose contrast enhancement of MR imaging at 0.3 T did not increase the diagnostic information for differentiating between scar and recurrent hernia. The high-dose images were considered more informative when evaluated in pairs, but gave no additional or different information when evaluated separately. The study also indicated that comparisons in pairs should be interpreted with caution. (orig.).

  10. Enhanced Crystalline Phase Purity of CH3NH3PbI3-xClx Film for High-Efficiency Hysteresis-Free Perovskite Solar Cells.

    Science.gov (United States)

    Yang, Yingguo; Feng, Shanglei; Xu, Weidong; Li, Meng; Li, Li; Zhang, Xingmin; Ji, Gengwu; Zhang, Xiaonan; Wang, Zhaokui; Xiong, Yimin; Cao, Liang; Sun, Baoquan; Gao, Xingyu

    2017-07-12

    Despite rapid successful developments toward promising perovskite solar cells (PSCs) efficiency, they often suffer significant hysteresis effects. Using synchrotron-based grazing incidence X-ray diffraction (GIXRD) with different probing depths by varying the incident angle, we found that the perovskite films consist of dual phases with a parent phase dominant in the interior and a child phase with a smaller (110) interplanar space (d(110)) after rapid thermal annealing (RTA), which is a widely used post treatment to improve the crystallization of solution-processed perovskite films for high-performance planar PSCs. In particular, the child phase composition gradually increases with decreasing depth till it becomes the majority on the surface, which might be one of the key factors related to hysteresis in fabricated PSCs. We further improve the crystalline phase purity of the solution-processed CH3NH3PbI3-xClx perovskite film (referred as g-perovskite) by using a facile gradient thermal annealing (GTA), which shows a uniformly distributed phase structure in pinhole-free morphology with less undercoordinated Pb and I ions determined by synchrotron-based GIXRD, grazing incidence small-angle X-ray scattering, scanning electron microscopy, and X-ray photoelectron spectroscopy. Regardless of device structures (conventional and inverted types), the planar heterojunction PSCs employing CH3NH3PbI3-xClx g-perovskite films exhibit negligible hysteresis with a champion power conversion efficiency of 17.04% for TiO2-based conventional planar PSCs and 14.83% for poly(3,4-ethylenedioxythiophene:poly(styrenesulfonate) (PEDOT:PSS)-based inverted planar PSCs. Our results indicate that the crystalline phase purity in CH3NH3PbI3-xClx perovskite film, especially in the surface region, plays a crucial role in determining the hysteresis effect and device performance.

  11. Distribution profile of gadolinium in gadolinium chelate-treated renally-impaired rats: role of pharmaceutical formulation.

    Science.gov (United States)

    Fretellier, Nathalie; Salhi, Mariem; Schroeder, Josef; Siegmund, Heiko; Chevalier, Thibaut; Bruneval, Patrick; Jestin-Mayer, Gaëlle; Delaloge, Francette; Factor, Cécile; Mayer, Jean-François; Fabicki, Jean-Michel; Robic, Caroline; Bonnemain, Bruno; Idée, Jean-Marc; Corot, Claire

    2015-05-25

    While not acutely toxic, chronic hepatic effect of certain gadolinium chelates (GC), used as contrast agent for magnetic resonance imaging, might represent a risk in renally-impaired patients due to free gadolinium accumulation in the liver. To answer this question, this study investigated the consequences of the presence of small amounts of either a soluble gadolinium salt ("free" Gd) or low-stability chelating impurity in the pharmaceutical solution of gadoteric acid, a macrocyclic GC with high thermodynamic and kinetic stabilities, were investigated in renally-impaired rats. Renal failure was induced by adding 0.75% adenine in the diet for three weeks. The pharmaceutical and commercial solution of gadoteric acid was administered (5 daily intravenous injections of 2.5 mmol Gd/kg) either alone or after being spiked with either "free" gadolinium (i.e., 0.04% w/v) or low-stability impurity (i.e., 0.06 w/v). Another GC, gadodiamide (low thermodynamic and kinetic stabilities) was given as its commercial solution at a similar dose. Non-chelated gadolinium was tested at two doses (0.005 and 0.01 mmol Gd/kg) as acetate salt. Gadodiamide induced systemic toxicity (mortality, severe epidermal and dermal lesions) and substantial tissue Gd retention. The addition of very low amounts of "free", non-chelated gadolinium or low thermodynamic stability impurity to the pharmaceutical solution of the thermodynamically stable GC gadoteric acid resulted in substantial capture of metal by the liver, similar to what was observed in "free" gadolinium salt-treated rats. Relaxometry studies strongly suggested the presence of free and soluble gadolinium in the liver. Electron microscopy examinations revealed the presence of free and insoluble gadolinium deposits in hepatocytes and Kupffer cells of rats treated with gadoteric acid solution spiked with low-stability impurity, free gadolinium and gadodiamide, but not in rats treated with the pharmaceutical solution of gadoteric acid. The

  12. Kinetic and microstructural studies of thermal decomposition in uranium mononitride compacts subjected to heating in high-purity helium

    Science.gov (United States)

    Lunev, A. V.; Mikhalchik, V. V.; Tenishev, A. V.; Baranov, V. G.

    2016-07-01

    Although uranium mononitride has a high melting point (≈3100 K), it often decomposes well below this temperature. The threshold and kinetics of thermal decomposition depend on samples' chemical content and on gas environment. However, most experiments with uranium nitride samples were done so far in vacuum conditions and did not allow thorough examination of reaction kinetics at high temperatures. This research focuses on studying the different stages of thermal decomposition in uranium nitride samples subjected to heating in helium. Mass loss and thermal effects are identified with simultaneous thermal analysis (STA), while scanning electron microscopy (SEM) and X-ray diffraction (XRD) are used to register phase and compositional changes. Thermal decomposition in uranium nitride samples is found to be a multi-stage process with the final stage characterized by uranium vaporization. The results are useful for estimating the high-temperature behaviour of uranium nitride fuel during its fabrication and performance in some of Gen IV reactors.

  13. Trace amounts of rare earth elements in high purity samarium oxide by sector field inductively coupled plasma mass spectrometry after separation by HPLC

    Energy Technology Data Exchange (ETDEWEB)

    Pedreira, W.R. [Instituto de Geociencias, Universidade de Brasilia (UnB), 70910-900 Brasilia, DF (Brazil) and Fundacao Jorge Duprat Figueiredo de Seguranca e Medicina do Trabalho (FUNDACENTRO), 05409-002 Sao Paulo, SP (Brazil)]. E-mail: walter.pedreira@fundacentro.gov.br; Queiroz, C.A. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), 05508-900 Sao Paulo, SP (Brazil); Abrao, A. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), 05508-900 Sao Paulo, SP (Brazil); Rocha, S.M. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), 05508-900 Sao Paulo, SP (Brazil); Vasconcellos, M.E. de [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), 05508-900 Sao Paulo, SP (Brazil); Boaventura, G.R. [Instituto de Geociencias, Universidade de Brasilia (UnB), 70910-900 Brasilia, DF (Brazil); Pimentel, M.M. [Instituto de Geociencias, Universidade de Brasilia (UnB), 70910-900 Brasilia, DF (Brazil)

    2006-07-20

    Today there is an increasing need for high purity rare earth compounds in various fields, the optical, the electronics, the ceramic, the nuclear and geochemistry. Samarium oxide has special uses in glass, phosphors, lasers and thermoelectric devices. Calcium chloride crystals treated with samarium have been employed in lasers, which produce light beams intense enough to burn metal. In general, the inductively coupled plasma mass spectrometry (ICP-MS) presents some advantages for trace element analysis, due to high sensitivity and resolution, when compared with other analytical techniques such as ICP optical emission spectrometry (ICP-OES). In this work, sector field inductively coupled plasma mass spectrometry was used. Sixteen elements (Sc, Y and 14 lanthanides) were determined selectively with the ICP-MS system using a concentration gradient method. The detection limits with the ICP-MS system were about 0.2 (La) pg mL{sup -1} to 8 (Gd) pg mL{sup -1}. The %R.S.D. of the methods varying between 0.9 and 1.5% for a set of five (n = 5) replicates was found for the IPEN's material and for the certificate reference sample. Determination of trace REEs in two high pure samarium oxides samples (IPEN and JMC) was performed. IPEN's material is highly pure (>99.99%) and was successfully analyzed without spectral interference (MO{sup +} and MOH{sup +})

  14. The effect of austenitizing treatments on the microstructure and creep properties of commercial and high purity 1/2Cr-1/2Mo-1/4V steels

    Energy Technology Data Exchange (ETDEWEB)

    Varma, R.K.; Tipler, H.R.

    1980-08-01

    Techniques used to produce specimens with specific creep properties from two types of 1/2 Cr 1/2 Mo 1/4 V steel, i.e., high purity and commercial purity, having different hardening and grain growth characteristics are described. The production of steels with identical microstructures was desired to provide material for an investigation of the effect of complex stresses in creep. Material for samples was produced by hot rolling at 1050 C. In general the high purity steel has better hardening characteristics and is also more prone to grain growth. Consequently, it was necessary to investigate the effects of various austenitizing conditions and of different rates of cooling on the microstructures obtained. The results of unlaxial creep tests are consistent with those previously obtained on similar steels. (ESA)

  15. The Research Progress of Determination Method for Impurities in High Purity Alkali Metal Salt%高纯碱金属盐中杂质测定方法的研究进展

    Institute of Scientific and Technical Information of China (English)

    王晓辉

    2011-01-01

    高纯碱金属盐的纯度对其应用有很大影响,痕量杂质元素含量的严格控制和准确测定非常重要.本文对高纯碱金属盐中的杂质分析方法(原子吸收光谱法、分光光度法、电感耦合等离子体光谱法、电感耦合等离子体质谱法、离子色谱法等)进行了综述.%The purity of high purity alkali metal salt effects the application a lot. The strictly control and accurate determination of trace impurity is very important. The analysis methods (atomic absorption spectrometry, spectrophotometry, ICP-AES, ICP-MS, ion chromatography) for impurities in high purity alkali metal salt are summarized in this paper.

  16. Major Role of NAD-Dependent Lactate Dehydrogenases in the Production of l-Lactic Acid with High Optical Purity by the Thermophile Bacillus coagulans.

    Science.gov (United States)

    Wang, Limin; Cai, Yumeng; Zhu, Lingfeng; Guo, Honglian; Yu, Bo

    2014-12-01

    Bacillus coagulans 2-6 is an excellent producer of optically pure l-lactic acid. However, little is known about the mechanism of synthesis of the highly optically pure l-lactic acid produced by this strain. Three enzymes responsible for lactic acid production-NAD-dependent l-lactate dehydrogenase (l-nLDH; encoded by ldhL), NAD-dependent d-lactate dehydrogenase (d-nLDH; encoded by ldhD), and glycolate oxidase (GOX)-were systematically investigated in order to study the relationship between these enzymes and the optical purity of lactic acid. Lactobacillus delbrueckii subsp. bulgaricus DSM 20081 (a d-lactic acid producer) and Lactobacillus plantarum subsp. plantarum DSM 20174 (a dl-lactic acid producer) were also examined in this study as comparative strains, in addition to B. coagulans. The specific activities of key enzymes for lactic acid production in the three strains were characterized in vivo and in vitro, and the levels of transcription of the ldhL, ldhD, and GOX genes during fermentation were also analyzed. The catalytic activities of l-nLDH and d-nLDH were different in l-, d-, and dl-lactic acid producers. Only l-nLDH activity was detected in B. coagulans 2-6 under native conditions, and the level of transcription of ldhL in B. coagulans 2-6 was much higher than that of ldhD or the GOX gene at all growth phases. However, for the two Lactobacillus strains used in this study, ldhD transcription levels were higher than those of ldhL. The high catalytic efficiency of l-nLDH toward pyruvate and the high transcription ratios of ldhL to ldhD and ldhL to the GOX gene provide the key explanations for the high optical purity of l-lactic acid produced by B. coagulans 2-6. Copyright © 2014, American Society for Microbiology. All Rights Reserved.

  17. Clonal Expansion of Lgr5-Positive Cells from Mammalian Cochlea and High-Purity Generation of Sensory Hair Cells

    Directory of Open Access Journals (Sweden)

    Will J. McLean

    2017-02-01

    Full Text Available Death of cochlear hair cells, which do not regenerate, is a cause of hearing loss in a high percentage of the population. Currently, no approach exists to obtain large numbers of cochlear hair cells. Here, using a small-molecule approach, we show significant expansion (>2,000-fold of cochlear supporting cells expressing and maintaining Lgr5, an epithelial stem cell marker, in response to stimulation of Wnt signaling by a GSK3β inhibitor and transcriptional activation by a histone deacetylase inhibitor. The Lgr5-expressing cells differentiate into hair cells in high yield. From a single mouse cochlea, we obtained over 11,500 hair cells, compared to less than 200 in the absence of induction. The newly generated hair cells have bundles and molecular machinery for transduction, synapse formation, and specialized hair cell activity. Targeting supporting cells capable of proliferation and cochlear hair cell replacement could lead to the discovery of hearing loss treatments.

  18. The production of ultra-high purity single isotopes or tailored isotope mixtures by ICP-MS

    Energy Technology Data Exchange (ETDEWEB)

    Liezers, Martin; Farmer, Orville T.; Dion, Michael P.; Thomas, Linda MP; Eiden, Gregory C.

    2015-01-01

    We report the development and testing of a simple collector arrangement for a commercial quadrupole ICP-MS that for the first time has been used to produce small quantities of highly enriched (>99.99%) single isotopes, with deposition rates >10 ng/hour. The collector assembly replaces the standard instrument detector allowing for implantation with simultaneous monitoring of the incident ion current. Even under zero bias implant conditions, low energy (<10 eV), ion collection efficiency was observed to be very high ~99%. 151Eu ion currents of 0.1-0.5 nA were collected on a simple, planar foil without resorting to any type of cup configuration. Recovery of the enriched isotope from such foils is much simpler than from a more complex cup configuration. High rejection of adjacent mass isotopes was demonstrated by selectively implanting 167Er without any discernible co-implantation of 166Er and 168Er. The important analytical possibilities of the new approach to isotope ratio measurement, tracer purification and radiation measurements are discussed.

  19. A novel method for purifying bluetongue virus with high purity by co-immunoprecipitation with agarose protein A

    Directory of Open Access Journals (Sweden)

    Ming Dai

    2010-06-01

    Full Text Available Abstract Background Bluetongue virus (BTV is an icosahedral non-enveloped virus within the genus Orbivirus of Reoviridae and exists as 24 distinct serotypes. BTV can infect all ruminant species and causes severe sickness in sheep. Recently, it was reported that BTV can infect some human cancer cells selectively. Because of the important oncolysis of this virus, we developed a novel purifying method for large-scale production. The purifying logic is simple, which is picking out all the components unwanted and the left is what we want. The process can be summarized in 4 steps: centrifugation, pulling down cell debrises and soluble proteins by co-immunoprecipitation with agarose Protein A, dialysis and filtration sterilization after concentration. Results The result of transmission electron microscope (TEM observation showed that the sample of purified virus has a very clear background and the virions still kept intact. The result of 50% tissue culture infective dose (TCID50 assay showed that the bioactivity of purified virus is relatively high. Conclusions This method can purify BTV-10 with high quality and high biological activity on large-scale production. It also can be used for purifying other BTV serotypes.

  20. Improving efficiency and color purity of poly(9,9-dioctylfluorene) through addition of a high boiling-point solvent of 1-chloronaphthalene

    Science.gov (United States)

    Liang, Junfei; Yu, Lei; Zhao, Sen; Ying, Lei; Liu, Feng; Yang, Wei; Peng, Junbiao; Cao, Yong

    2016-07-01

    In this work, the β-phase of poly(9,9-dioctylfluorene) (PFO) was used as a probe to study the effects of the addition of a high boiling-point solvent of 1-chloronaphthalene on the nanostructures and electroluminescence of PFO films. Both absorption and photoluminescence spectra showed that the content of the β-phase in PFO film was obviously enhanced as a result of the addition of a small amount of 1-chloronaphthalene into the processing solvent of p-xylenes. Apparently rougher morphology associated with the effectively enhanced ordering of polymer chains across the entire film was observed for films processed from p-xylene solutions consisting of a certain amount of 1-chloronaphthalene, as revealed by atomic force microscopy and grazing incidence x-ray diffraction measurements. In addition to the effects on the nanostructures of films, of particular interest is that the performance and color purity of polymer light-emitting devices can be noticeably enhanced upon the addition of 1-chloronaphthalene. These observations highlight the importance of controlling the nanostructures of the emissive layer, and demonstrate that the addition of a low volume ratio of high boiling-point additive can be a promising strategy to attain high-performance polymer light-emitting diodes.

  1. Field-strength dependence of Gadolinium enhancement: Theory and implications

    Energy Technology Data Exchange (ETDEWEB)

    Elster, A.D. [Wake Forest Univ., Winston-Salem, NC (United States)

    1994-09-01

    The decision to use contrast in magnetic resonance (MR) examination has important diagnostic, economic, and medicolegal implications. The overwhelmng majority of published studies defining the clinical utility of gadolinium administration for neuroimaging have been performed at high fields. Are these conclusions about contrast agent use at high fields equally valid for low-field imaging? Is contrast enhancement at 1.5T the same as contrast enhancement at 0.15T? The relationship between field stregth and contrast enhancement is sufficiently complex that few readers will find it intuitively obvious. This commentary reviews and further develops the theoretical framework necessary to explain the field dependence of gadolinium enhancement in tissues.

  2. Rapid, high-purity chemical separation of molybdenum from iron meteorites for isotopic analysis by using thermal ionization mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Qi-Lu; Masuda, Akimasa (Tokyo Univ. (Japan). Dept. of Chemistry)

    1992-05-01

    A chemical procedure has been developed, which combines both solvent extraction and anion exchange, so that microgram amounts of Mo can be cleanly, rapidly and efficiently separated from gram amounts of iron meteorites. Particular attention was directed to the complete separation of Mo from Zr and Ru. The isotopic abundance ratios of Mo can subsequently be determined with high accuracy by using thermal ionization mass spectrometry. The experiments indicate that the behaviour of Mo during solvent extraction and anion exchange is considerably different from that reported previously. In particular, it was found that there is a very narrow range of HCl concentrations within which it is possible to separate Mo from Fe by solvent extraction. The reproducibility and recovery of the method were examined by using inductively coupled plasma atomic emission spectrometry. (Author).

  3. Positron lifetime in polycrystalline gadolinium

    Energy Technology Data Exchange (ETDEWEB)

    Gomez, A.M.; Serna, J. (Universidad Complutense de Madrid (Spain). Dept. de Fisica del Estado Solido)

    1984-06-16

    Positron lifetimes are measured on polycrystalline gadolinium between 15 and 25 /sup 0/C taking into account the microstructure of the specimens, especially the grain sizes of untreated or annealed sheets. Results show the existence of a trapping effect of positrons in Gd due to different trapping centers such as point defects, dislocations, grain boundaries, and other defects.

  4. Purity matters: A workflow for the valid high-resolution lipid profiling of mitochondria from cell culture samples.

    Science.gov (United States)

    Kappler, Lisa; Li, Jia; Häring, Hans-Ulrich; Weigert, Cora; Lehmann, Rainer; Xu, Guowang; Hoene, Miriam

    2016-02-19

    Subcellular lipidomics is a novel field of research that requires the careful combination of several pre-analytical and analytical steps. To define a reliable strategy for mitochondrial lipid profiling, we performed a systematic comparison of different mitochondria isolation procedures by western blot analyses and comprehensive high-resolution lipidomics. Using liver-derived HepG2 cells, we compared three common mitochondria isolation methods, differential centrifugation (DC), ultracentrifugation (UC) and a magnetic bead-assisted method (MACS). In total, 397 lipid species, including 32 cardiolipins, could be quantified in only 100 μg (by protein) of purified mitochondria. Mitochondria isolated by UC showed the highest enrichment in the mitochondria-specific cardiolipins as well as their precursors, phosphatidylglycerols. Mitochondrial fractions obtained by the commonly used DC and the more recent MACS method contained substantial contaminations by other organelles. Employing these isolation methods when performing lipidomics analyses from cell culture mitochondria may lead to inaccurate results. To conclude, we present a protocol how to obtain reliable mitochondria-specific lipid profiles from cell culture samples and show that quality controls are indispensable when performing mitochondria lipidomics.

  5. 鹅肝细胞的高纯分离及培养%Isolation and culture of high-purity goose hepatocytes

    Institute of Scientific and Technical Information of China (English)

    洪胜辉; 张军; 邵丹; 张宜辉; 张蕊; 王来娣; 龚道清

    2012-01-01

    Using the simple method of collagenase digestion directly'to isolate goose embryo hepatocytes and can acquire a large high viability and high purity of hepatocytes. HE dyed showed that mostly hepatocytes have two or more nucleus which demonstrate cells have strong proliferation split ability . The specific gene albumin gene test showed that isolated cells are mature hepatocytes. It is a easily and effective method which can get primary goose hepatocyte.%采用简单的"胶原酶直接消化法"分离鹅胚胎肝细胞,得到的肝细胞纯度高,活性好;HE染色显示大量双核或多核细胞,细胞具有旺盛增殖分裂能力;肝脏特异性基因白蛋白基因检测显示所分离细胞为成熟肝脏细胞。该法操作简单、高效,是获得鹅原代肝细胞的一种较好的方法,有利于以鹅原代肝细胞为模型的体外研究工作的开展。

  6. High-purity preparation of HSV-2 vaccine candidate ACAM529 is immunogenic and efficacious in vivo.

    Directory of Open Access Journals (Sweden)

    Sophia T Mundle

    Full Text Available Genital herpes is a sexually transmitted infection (STI caused by herpes simplex virus 2 (HSV-2 and to a lesser extent herpes simplex virus 1 (HSV-1. Infection by HSV-2 is life-long and is associated with significant cost to healthcare systems and social stigma despite the highly prevalent nature of the disease. For instance, the proportion of HSV-2 seropositive to seronegative adults is approximately 1 in 5 in the US and greater than 4 in 5 in some areas of sub-Saharan Africa. The replication-defective vaccine strain virus dl5-29 was re-derived using cells appropriate for GMP manufacturing and renamed ACAM529. Immunization with dl5-29 was previously reported to be protective both in mice and in guinea pigs, however these studies were performed with vaccine that was purified using methods that cannot be scaled for manufacturing of clinical material. Here we describe methods which serve as a major step towards preparation of ACAM529 which may be suitable for testing in humans. ACAM529 can be harvested from infected cell culture of the trans-complementing cell line AV529 clone 19 (AV529-19 without mechanical cell disruption. ACAM529 may then be purified with respect to host cell DNA and proteins by a novel purification scheme, which includes a combination of endonuclease treatment, depth filtration, anion-exchange chromatography and ultrafiltration/diafiltration (UF/DF. The resultant virus retains infectivity and is ∼ 200-fold more pure with respect to host cell DNA and proteins than is ACAM529 purified by ultracentrifugation. Additionally, we describe a side-by-side comparison of chromatography-purified ACAM529 with sucrose cushion-purified ACAM529, which shows that both preparations are equally immunogenic and protective when tested in vivo.

  7. Sensitivity of alanine dosimeters with gadolinium exposed to 6 MV photons at clinical doses.

    Science.gov (United States)

    Marrale, M; Longo, A; Spanò, M; Bartolotta, A; D'Oca, M C; Brai, M

    2011-12-01

    In this study we analyzed the ESR signal of alanine dosimeters with gadolinium exposed to 6 MV linear accelerator photons. We observed that the addition of gadolinium brings about an improvement in the sensitivity to photons because of its high atomic number. The experimental data indicated that the addition of gadolinium increases the sensitivity of the alanine to 6 MV photons. This enhancement was better observed at high gadolinium concentrations for which the tissue equivalence is heavily reduced. However, information about the irradiation setup and of the radiation beam features allows one to correct for this difference. Monte Carlo simulations were carried out to obtain information on the expected effect of the addition of gadolinium on the dose absorbed by the alanine molecules inside the pellets. These results are compared with the experimental values, and the agreement is discussed.

  8. Use of alkali metal salts to prepare high purity single-walled carbon nanotube solutions and thin films

    Science.gov (United States)

    Ashour, Rakan F.

    Single-walled carbon nanotubes (SWCNTs) display interesting electronic and optical properties desired for many advanced thin film applications, such as transparent conductive electrodes or thin-film transistors. Large-scale production of SWCNTs generally results in polydispersed mixtures of nanotube structures. Since SWCNT electronic character (conducting or semiconducting nature) depends on the nanotube structure, application performance is being held back by this inability to discretely control SWCNT synthesis. Although a number of post-production techniques are able to separate SWCNTs based on electronic character, diameter, or chirality, most still suffer from the disadvantage of high costs of materials, equipment, or labor intensity to be relevant for large-scale production. On the other hand, chromatographic separation has emerged as a method that is compatible with large scale separation of metallic and semiconducting SWCNTs. In this work, SWCNTs, in an aqueous surfactant suspension of sodium dodecyl sulfate (SDS), are separated by their electronic character using a gel chromatography process. Metallic SWCNTs (m-SWCNTs) are collected as initial fractions since they show minimum interaction with the gel medium, whereas, semiconducting SWCNTs (sc- SWCNTs) remain adsorbed to the gel. The process of sc-SWCNT retention in the gel is found to be driven by the packing density of SDS around the SWCNTs. Through a series of separation experiments, it is shown that sc-SWCNTs can be eluted from the gel simply by disturbing the configuration of the SDS/SWCNT micellar structure. This is achieved by either introducing a solution containing a co-surfactant, such as sodium cholate (SC), or solutions of alkali metal ionic salts. Analysis of SWCNT suspensions by optical absorption provides insights into the effect of changing the metal ion (M+ = Li+, Na+, and K+) in the eluting solution. Salts with smaller metal ions (e.g. Li+) require higher concentrations to achieve

  9. 高纯度对硝基苯胺制备工艺研究%Research on production technology of p-nitroaniline with high purity

    Institute of Scientific and Technical Information of China (English)

    储政

    2012-01-01

    利用对硝基氯苯氨解制备对硝基苯胺,研究了反应温度、氨水质量分数、反应时间以及结晶母液循环使用次数对该氨解工艺的影响.研究结果表明:该工艺不仅产生的废水量少,而且制得的对硝基苯胺纯度高且不需要提纯处理;在对硝基氯苯用量为31.5g,氨水加入量为300.0 mL,氨水浓度约为35%,反应温度为170.0℃,反应时间为8.0h条件下,对硝基氯苯的转化率为100%,生成的对硝基苯胺纯度为99.9%,对硝基苯胺收率为97.7%;本工艺条件下结晶母液可以循环套用5次.%p-Nitroaniline is prepared by aminolysising of p-nitrochlorobenzene. The effects of reaction temperature, the concentration of ammonia solution, reaction time and the times of recycling the mother solution on the aminolysising process are investigated. The results show that, this process discharges less waste water but produces high-purity p-nitrochlorobenzene without the purification step. The conversion of p-nitrochlorobenzene and the purity of the formed p-nitroaniline can reach 100% and 99. 9% , respectively, under the following conditions: 31. 5 g of p-nitrochlorobenzene, 300. 0 mL of 35% ammonia solution, 170. 0℃ of reaction temperature and 8. 0 hours of reaction time. The yield of p-nitroaniline is 97. 7%. The mother solution can be recycled for five times.

  10. 高纯度粉末状大豆磷脂微胶囊化的研究%Study on microencapsulation of high purity soybean phosphatide powder

    Institute of Scientific and Technical Information of China (English)

    张鑫; 李学红; 高正波

    2001-01-01

    选用新型壁材—微孔淀粉,对制备高纯度粉末状大豆磷脂微胶囊产品的工艺条件进行研究。以100g大豆磷脂,100g微孔淀粉和40g明胶在40℃条件下制备初始液,在进料温度50~60℃,进风温度160℃左右,出风温度90℃左右条件下进行喷雾干燥,可获得最佳效果。最高包埋率可达71%。%With a new wall material-aperture starch, the technological parameters for high-purity soybean powder phosphatide microencapsulation was studied. For 100g soybean phosphatide, 100g aperture starch and 40g gelatin were added to form a 1500mL preliminary solution at 40℃. Condition of spry drying: Slurry temperature 50~60℃, inlet air temperature 150~160℃ and outlet air temperature 90℃, could obtain the optimal result and the best microencapsulated productivity reached 71%.

  11. Genotypic and phenotypic diversity of Ralstonia pickettii and Ralstonia insidiosa isolates from clinical and environmental sources including High-purity Water. Diversity in Ralstonia pickettii

    Directory of Open Access Journals (Sweden)

    Adley Catherine C

    2011-08-01

    Full Text Available Abstract Background Ralstonia pickettii is a nosocomial infectious agent and a significant industrial contaminant. It has been found in many different environments including clinical situations, soil and industrial High Purity Water. This study compares the phenotypic and genotypic diversity of a selection of strains of Ralstonia collected from a variety of sources. Results Ralstonia isolates (fifty-nine from clinical, industrial and environmental origins were compared genotypically using i Species-specific-PCR, ii PCR and sequencing of the 16S-23S rRNA Interspatial region (ISR iii the fliC gene genes, iv RAPD and BOX-PCR and v phenotypically using biochemical testing. The species specific-PCR identified fifteen out of fifty-nine designated R. pickettii isolates as actually being the closely related species R. insidiosa. PCR-ribotyping of the 16S-23S rRNA ISR indicated few major differences between the isolates. Analysis of all isolates demonstrated different banding patterns for both the RAPD and BOX primers however these were found not to vary significantly. Conclusions R. pickettii species isolated from wide geographic and environmental sources appear to be reasonably homogenous based on genotypic and phenotypic characteristics. R. insidiosa can at present only be distinguished from R. pickettii using species specific PCR. R. pickettii and R. insidiosa isolates do not differ significantly phenotypically or genotypically based on environmental or geographical origin.

  12. Simultaneous determination of some trace metal impurities in high-purity sodium tungstate using coprecipitation and inductively coupled plasma atomic emission spectrometry

    Institute of Scientific and Technical Information of China (English)

    MA Xiaoguo; KUANG Tongchun; LIU Qianjun

    2004-01-01

    A method based on the combination of coprecipitation with inductively coupled plasma atomic emission spec trometry (ICP-AES) was developed for the determination of impurities in high-purity sodium tungstate. Six elements (Co,Cu, Fe, Mn, Ni, and Pb) were coprecipitated by lanthanum hydroxide so as to be concentrated and separated from the tungsten matrix. Effects of some factors on the recoveries of the analytes and on the residual amount of sodium tungstate were investigated, and the optimum conditions for the coprecipitation were proposed. Matrix-matching calibration curve method was used for the analysis. It is shown that the elements mentioned above can be quantitatively recovered. The detection limits for Co, Cu, Fe, Mn, Ni, and Pb are 0.07, 0.4, 0.2, 0.1, 0.6, and 1.3 μg.g-1, respectively. The recoveries vary from 92.5% to 108%, and the relative standard deviations (RSDs) are in the range of 3.1%-5.5%.

  13. Genotypic and phenotypic diversity of Ralstonia pickettii and Ralstonia insidiosa isolates from clinical and environmental sources including High-purity Water.

    LENUS (Irish Health Repository)

    Ryan, Michael P

    2011-08-30

    Abstract Background Ralstonia pickettii is a nosocomial infectious agent and a significant industrial contaminant. It has been found in many different environments including clinical situations, soil and industrial High Purity Water. This study compares the phenotypic and genotypic diversity of a selection of strains of Ralstonia collected from a variety of sources. Results Ralstonia isolates (fifty-nine) from clinical, industrial and environmental origins were compared genotypically using i) Species-specific-PCR, ii) PCR and sequencing of the 16S-23S rRNA Interspatial region (ISR) iii) the fliC gene genes, iv) RAPD and BOX-PCR and v) phenotypically using biochemical testing. The species specific-PCR identified fifteen out of fifty-nine designated R. pickettii isolates as actually being the closely related species R. insidiosa. PCR-ribotyping of the 16S-23S rRNA ISR indicated few major differences between the isolates. Analysis of all isolates demonstrated different banding patterns for both the RAPD and BOX primers however these were found not to vary significantly. Conclusions R. pickettii species isolated from wide geographic and environmental sources appear to be reasonably homogenous based on genotypic and phenotypic characteristics. R. insidiosa can at present only be distinguished from R. pickettii using species specific PCR. R. pickettii and R. insidiosa isolates do not differ significantly phenotypically or genotypically based on environmental or geographical origin.

  14. Use of zeo-karb 226 and dowex a-l in the analysis of high-purity zinc and zinc-base alloys for Tl and In.

    Science.gov (United States)

    Iyer, S G; Padmanabhan, P K; Nair, L D; Venkateswarlu, C

    1976-07-01

    Utility of Zeo-Karb 226 and Dowex A-l for the separation of Tl and In at 5-ppm level from high-purity zinc and zinc-base alloys has been investigated. With Zeo-Karb 226 (NH(4)(+)), T1(+) is conveniently separated from these materials and also from many other cations, with l.0M ammonium nitrate as the eluent. It is subsequently determined with Rhodamine B. This separation principle is also applied to the analysis of Pb-Tl alloys. Both Tl and In (along with Fe) are preconcentrated on Zeo-Karb 226(H(+)) from a solution of the sample at pH 3.0. Suitable methods of subsequent determination of Tl and In are described. In the case of Dowex A-1(H(+)), Tl(+), In(3+), Fe(3+) and Cu(2+) are retained from a solution of the sample at pH 2.0. An o-phenanthroline solution at pH 2.0 elutes all but traces of Cu(2+). In(3+) along with Fe(3+) is eluted with l.0M hydrochloric acid. Finally, Tl is eluted with 2.0M hydrochloric acid containing sulphurous acid.

  15. A method for high purity intestinal epithelial cell culture from adult human and murine tissues for the investigation of innate immune function.

    Science.gov (United States)

    Graves, Christina L; Harden, Scott W; LaPato, Melissa; Nelson, Michael; Amador, Byron; Sorenson, Heather; Frazier, Charles J; Wallet, Shannon M

    2014-12-01

    Intestinal epithelial cells (IECs) serve as an important physiologic barrier between environmental antigens and the host intestinal immune system. Thus, IECs serve as a first line of defense and may act as sentinel cells during inflammatory insults. Despite recent renewed interest in IEC contributions to host immune function, the study of primary IEC has been hindered by lack of a robust culture technique, particularly for small intestinal and adult tissues. Here, a novel adaptation for culture of primary IEC is described for human duodenal organ donor tissue as well as duodenum and colon of adult mice. These epithelial cell cultures display characteristic phenotypes and are of high purity. In addition, the innate immune function of human primary IEC, specifically with regard to Toll-like receptor (TLR) expression and microbial ligand responsiveness, is contrasted with a commonly used intestinal epithelial cell line (HT-29). Specifically, TLR expression at the mRNA level and production of cytokine (IFNγ and TNFα) in response to TLR agonist stimulation is assessed. Differential expression of TLRs as well as innate immune responses to ligand stimulation is observed in human-derived cultures compared to that of HT-29. Thus, use of this adapted method to culture primary epithelial cells from adult human donors and from adult mice will allow for more appropriate studies of IECs as innate immune effectors.

  16. 高纯难熔金属及其合金单晶的发展%Development of Single Crystals of High-Purity Refractory Metals and Alloys

    Institute of Scientific and Technical Information of China (English)

    李来平; 胡忠武; 殷涛; 张文; 高选乔; 郭林江; 任广鹏; 张平祥; 李中奎

    2014-01-01

    In this paper,we report the processing technology of single crystals of high-purity refractory metals and alloys, and compare the electron-beam floating zone melting(EBFZM)with the plasma arc melting(PAM).By EBFZM,the tem-perature gradient could be controlled easily and the contamination by crucible materials is avoided,whereas the surface tension of melt is sensitive to the active impurity content and the temperature gradient.Furthermore,the dimensions of high-purity refractory metals and the monocrystalline materials are severely limited and the dislocation density in the mate-rials is relatively high.PAM has the advantages such as high energy density of heating and various specifications of raw materials,by which the single crystal castings could be processed in the shape of rod,plate,tube and other specific shapes.Meanwhile,the impurity elements (especially carbon)are maximally removed.However,the equipment is com-plex and the dislocation density is high.We also discuss the status of development for single crystal materials,such as im-proving the resistance to high temperature and stablilty by solid-solution strengthening.The processing of single crystal tubes is also an interesting topic.We make some suggestions on the processing technology and developing prospect for sin-gle crystals of refractory metals and alloys.%介绍了难熔金属及其合金单晶的制备技术,对电子束悬浮区域熔炼技术和等离子弧熔炼技术进行了比较。电子束悬浮区域熔炼法温度梯度易于控制、材料不受坩埚材料污染,但熔体表面张力对活性杂质和温度梯度敏感性高,所能制备的高纯难熔金属及其单晶材料尺寸规格受到很大限制,且材料内部位错密度较高。等离子弧熔炼法加热源能量密度高,原料规格形式多样,可制备单晶棒材、板材、管材及其他特定形状的单晶铸件,可最大程度地去除杂质元素(尤其是C元素),但设备系统复杂,

  17. Towards modeling gadolinium-lead-borate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Rada, S., E-mail: Simona.Rada@phys.utcluj.ro [Department of Physics, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania); Ristoiu, T. [Department of Physics, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania); Rada, M. [Department of Mechatronic, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania); Coroiu, I. [Department of Physics, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania); Maties, V. [Department of Mechatronic, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania); Culea, E. [Department of Physics, Technical University of Cluj-Napoca, 400641 Cluj-Napoca (Romania)

    2010-01-15

    Infrared spectra of gadolinium-lead-borate glasses of the xGd{sub 2}O{sub 3}.(100 - x)[3B{sub 2}O{sub 3}.PbO] system, where x = 0, 5, 10, 15, 25, 35 and 50 mol.%, have been recorded to explore the role of content of gadolinium ions behaving as glass modifier. The FTIR spectroscopy data for the xGd{sub 2}O{sub 3}.(1 - x)[3B{sub 2}O{sub 3}.PbO] glasses show the structural role of lead ions as a network-formers and of the gadolinium ions network modifiers. Adding of the rare earth ion up to 35 mol.% into the glass matrix, the IR bands characteristic to the studied glasses become sharper and more pronounced. Structural changes, as recognized by analyzing band shapes of IR spectra, revealed that Gd{sub 2}O{sub 3} causes a change from the continuous borate network to the continuous lead-borate network interconnected through Pb-O-B and B-O-B bridges and the transformation of some tetrahedral [BO{sub 4}] units into trigonal [BO{sub 3}] units. Then, gadolinium ions have affinity towards [BO{sub 3}] structural units which contain non-bridging oxygens necessary for the charge compensation because the more electronegative [BO{sub 3}] structural units were implied in the formation of B-O-Gd bonds and the transformation of glass network into a glass ceramic. We propose a possible structural model of building blocks for the formation of continuous random 3B{sub 2}O{sub 3}.PbO network glass used by density functional theory (DFT) calculations. DFT calculations show that lead atoms occupy three different sites in the proposed model. The first is coordinated with six oxygen atoms forming distorted octahedral geometries. The second lead atom has an octahedral oxygen environment and the five longer Pb-O bonds are considered as participating in the metal coordination scheme. The third lead atom has ionic character. In agreement with the results offered by the experimental FTIR data, the theoretical IR data confirm that our proposed structure is highly possible.

  18. Firewalls From Double Purity

    CERN Document Server

    Bousso, Raphael

    2013-01-01

    The firewall paradox is often presented as arising from double entanglement, but I argue that more generally the paradox is double purity. Near-horizon modes are purified by the interior, in the infalling vacuum. Hence they cannot also be pure alone, or in combination with any third system, as demanded by unitarity. This conflict arises independently of the Page time, for entangled and for pure states. It implies that identifications of Hilbert spaces cannot resolve the paradox. Traditional complementarity requires the unitary identification of infalling matter with a scrambled subsystem of the Hawking radiation. Extending this map to the infalling vacuum overdetermines the out-state. More general complementarity maps ("A=R_B", "ER=EPR") founder when the near-horizon zone is pure. I argue that pure-zone states span the microcanonical ensemble, and that this suffices to make the horizon a special place. I advocate that the ability to detect the horizon locally, rather than the degree or probability of violence...

  19. Tumor growth suppression by gadolinium-neutron capture therapy using gadolinium-entrapped liposome as gadolinium delivery agent.

    Science.gov (United States)

    Dewi, Novriana; Yanagie, Hironobu; Zhu, Haito; Demachi, Kazuyuki; Shinohara, Atsuko; Yokoyama, Kazuhito; Sekino, Masaki; Sakurai, Yuriko; Morishita, Yasuyuki; Iyomoto, Naoko; Nagasaki, Takeshi; Horiguchi, Yukichi; Nagasaki, Yukio; Nakajima, Jun; Ono, Minoru; Kakimi, Kazuhiro; Takahashi, Hiroyuki

    2013-07-01

    Neutron capture therapy (NCT) is a promising non-invasive cancer therapy approach and some recent NCT research has focused on using compounds containing gadolinium as an alternative to currently used boron-10 considering several advantages that gadolinium offers compared to those of boron. In this study, we evaluated gadolinium-entrapped liposome compound as neutron capture therapy agent by in vivo experiment on colon-26 tumor-bearing mice. Gadolinium compound were injected intravenously via tail vein and allowed to accumulate into tumor site. Tumor samples were taken for quantitative analysis by ICP-MS at 2, 12, and 24 h after gadolinium compound injection. Highest gadolinium concentration was observed at about 2 h after gadolinium compound injection with an average of 40.3 μg/g of wet tumor tissue. We performed neutron irradiation at JRR-4 reactor facility of Japan Atomic Energy Research Institute in Tokaimura with average neutron fluence of 2×10¹² n/cm². The experimental results showed that the tumor growth suppression of gadolinium-injected irradiated group was revealed until about four times higher compared to the control group, and no significant weight loss were observed after treatment suggesting low systemic toxicity of this compound. The gadolinium-entrapped liposome will become one of the candidates for Gd delivery system on NCT.

  20. Preparation of High-purity Silica White Using Micro-silica Powder%微硅粉制取高纯白炭黑的工艺初探

    Institute of Scientific and Technical Information of China (English)

    李小英; 彭建蓉; 和晓才; 杨大锦

    2014-01-01

    Preparation of high-purity silica white by micro-silica powder roasting with alkaline clinker -leaching using water -solution purification -carbon dioxide decomposition -washing -calcination has been researched .The mixture of micro-silica powder with soda was roasted at 850 ℃ for 1 hour to prepare sodium metasilicate clinker .The clinker was leached with water at temperature of 70 ℃ ,then the impurity(Al ,Fe) in the leaching solution was removed with lime powder .Removal rate of Fe is 94% ,removal rate of Al is 56% ,the loss rate of SiO2 is 19% .The purified solution was carbon decomposition for 3-4 hours using CO2 to precipitate acid metasilicate at temperature of 50-60 ℃ , CO2 flow and air flow ratio of 1∶7 .0 -1∶7 .5 .The precipitated acid metasilicate was washed using hydrochloric acid and distilled water ,then was dried and calcined to obtain high-purity silica white with SiO2 grade over 99 .98% .For process ,the raw materials are readily available ,process is simple , no-pollution ,industrial silica powder can be fully used with high value .%研究了以微硅粉碱性焙烧-熟料浸出-溶液净化-碳分沉淀-洗涤-干燥-煅烧工艺制取白炭黑。将微硅粉与纯碱混合均匀,在850℃下焙烧1 h制成偏硅酸钠熟料;熟料水浸得偏硅酸钠溶液;偏硅酸钠溶液在水浴温度70℃下,用石灰粉搅拌净化1 h除杂,净化液中杂质Fe脱除率为94%,Al脱除率为56%,SiO2损失率为19%;净化液用CO2碳分沉淀,控制温度50~60℃,CO2流量与空气流量比为1∶7~1∶7.5,碳分时间3~4h,获得颗粒均匀的偏硅酸沉淀;偏硅酸经盐酸及蒸馏水洗涤后干燥煅烧得高纯白炭黑,白炭黑纯度在99.98%以上。此工艺原料易得,过程控制简单,不产生污染,可实现工业微硅粉的高值化利用。

  1. High prevalence of nephrogenic systemic fibrosis in chronic renal failure patients exposed to gadodiamide, a gadolinium-containing magnetic resonance contrast agent

    DEFF Research Database (Denmark)

    Rydahl, Casper; Thomsen, Henrik S; Marckmann, Peter

    2008-01-01

    OBJECTIVE: Nephrogenic systemic fibrosis (NSF) is a serious disease affecting renal failure patients. It may be caused by some gadolinium (Gd)-containing contrast agents, including gadodiamide. The study aimed at estimating the prevalence of NSF after gadodiamide exposure for patients with chronic...... kidney disease (CKD). MATERIALS AND METHODS: Retrospective cohort study of 190 consecutive nephrological patients in different categories of kidney function referred for gadodiamide-enhanced magnetic resonance imaging in the period January 1, 2004 to March 21, 2006. RESULTS: Eighteen patients (18/190; 10......%, 95% CI: 6%-15%) were diagnosed with NSF within a mean follow-up period of 29 months (range 16-43 months). All 18 cases had stage 5 CKD (ie, estimated glomerular filtration rate less than 15 mL/min/1.73 m2 or in dialysis therapy) at the time of their gadodiamide exposure. The prevalence of NSF among...

  2. Neutron Damage in Mechanically-Cooled High-Purity Germanium Detectors for Field-Portable Prompt Gamma Neutron Activation Analysis (PGNAA) Systems

    Energy Technology Data Exchange (ETDEWEB)

    E.H. Seabury; C.J. Wharton; A.J. Caffrey; J.B. McCabe; C. DeW. Van Siclen

    2013-10-01

    Prompt Gamma Neutron Activation (PGNAA) systems require the use of a gamma-ray spectrometer to record the gamma-ray spectrum of an object under test and allow the determination of the object’s composition. Field-portable systems, such as Idaho National Laboratory’s PINS system, have used standard liquid-nitrogen-cooled high-purity germanium (HPGe) detectors to perform this function. These detectors have performed very well in the past, but the requirement of liquid-nitrogen cooling limits their use to areas where liquid nitrogen is readily available or produced on-site. Also, having a relatively large volume of liquid nitrogen close to the detector can impact some assessments, possibly leading to a false detection of explosives or other nitrogen-containing chemical. Use of a mechanically-cooled HPGe detector is therefore very attractive for PGNAA applications where nitrogen detection is critical or where liquid-nitrogen logistics are problematic. Mechanically-cooled HPGe detectors constructed from p-type germanium, such as Ortec’s trans-SPEC, have been commercially available for several years. In order to assess whether these detectors would be suitable for use in a fielded PGNAA system, Idaho National Laboratory (INL) has been performing a number of tests of the resistance of mechanically-cooled HPGe detectors to neutron damage. These detectors have been standard commercially-available p-type HPGe detectors as well as prototype n-type HPGe detectors. These tests compare the performance of these different detector types as a function of crystal temperature and incident neutron fluence on the crystal.

  3. New process for purifying high purity α1-antitrypsin from Cohn Fraction IV by chromatography: A promising method for the better utilization of plasma.

    Science.gov (United States)

    Huangfu, Chaoji; Zhang, Jinchao; Ma, Yuyuan; Jia, Junting; Lv, Maomin; Zhao, Xiong; Zhang, Jingang

    2017-03-01

    α1-antitrypsin (AAT) is a 52kDa serine protease inhibitor that is abundant in plasma. It is synthesized mainly by hepatic cells, and widely used to treat patients with emphysema due to congenital deficiency of AAT. A new isolation method for the purification of AAT from Cohn Fraction IV (Cohn F IV) is described. Cohn F IV is usually discarded as a byproduct from Cohn process. Using Cohn F IV as starting material does not interfere with the production of other plasma proteins and the cost of purification could be reduced greatly. Parameters of each step during purification were optimized, 15% polyethyleneglycol (PEG) concentration and pH 5.2 for PEG precipitation, elution with 0.05M sodium acetate and pH 4.7 for ion-exchange chromatography, and two steps blue sepharose affinity chromatography were chosen for AAT purification. The final protein with purity of 98.17%, specific activity of 3893.29 IU/mg, and yield of 28.35%, was achieved. Western blotting was applied for qualitative identification of final product, which specifically reacted with goat anti-human AAT antibody. LC-ESI-MS/MS was also employed to confirm the final protein. High performance liquid chromatography was used to analyze the composition of purified protein suggesting that pure protein was achieved. The molecular weight of AAT is 51062.77Da which was identified by LC-MS-MS. The manufacturing process described here may make better use of human plasma with Cohn F IV as starting material. The simple process described in this study is simple and inexpensive, it has a potential value for large scale production. Copyright © 2017 Elsevier B.V. All rights reserved.

  4. Controllable biosynthesis of high-purity lead-sulfide (PbS) nanocrystals by regulating the concentration of polyethylene glycol in microbial system.

    Science.gov (United States)

    Yue, Lei; Wang, Jia; Zhang, Yongtao; Qi, Shiyue; Xin, Baoping

    2016-12-01

    We demonstrated a simple biological method to explore the controllable synthesize of high-purity PbS nanocrystals by regulating the concentration of polyethylene glycol in microbial system. The biogenic H2S produced via the reduction of sulfate precipitated Pb(2+) ions as sulfide extracellularly, and the optimal removal rate of Pb(2+) ions is up to 96.7 % in 2 weeks. The characterization results showed that PbS nanocuboids with a particle size 50 × 50 × 100 nm obtained from Case A with 4 mM polyethylene glycol as a dispersant, and can completely degrade methylene blue from solution within 20 h; PbS nanosheets with a thickness size ca. 10 nm attained from Case B with 12 mM polyethylene glycol, and it can degrade 61.6 % dye within 24 h; PbS nanoparticles with a uniform diameter of ca. 60 nm formed from Case C with 20 mM polyethylene glycol, only degrade 14.1 % dye within 24 h. It is interesting that the factor affecting their catalytic activities is not the specific surface area, but the number of [200] crystal plane. This work not only displayed a simple synthetic method to control the morphology of PbS nanocrystals in microbial system, but also provided an economic and environmentally friendly approach for resourceful treatment and efficient bioremediation of wastewater-containing heavy metal.

  5. Contribution to the study of the conductivity of high purity water; Contribution a l'etude de la conductivite de l'eau de haute purete

    Energy Technology Data Exchange (ETDEWEB)

    Nens, Ch. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    In this work a study is made more particularly of two points: the production of high purity water and the estimation of this purity by means of conductivity measurements. As far as water purification is concerned it is observed that the de-ionisation produced by ion exchange resins in mixed beds leads to a water having a lower conductivity than that obtained by distillation. This low conductivity however, measured at the column exit before the water comes into contact with air is not stable. In fact the carbon dioxide in the water gives rise to an equilibrium with production of the ions HCO{sub 3}{sup -}, CO{sub 3}{sup --}. These ions are retained during the passage of the water through the resins. They reappear again at the column exit as a result of the displacement of the hydration equilibrium of CO{sub 2}; because of this the conductivity of the water increases with time. The water obtained by successive distillations does not behave in the same way because no carbon dioxide is present. Distillation is however a costly purification process on an industrial scale, especially if large quantities of water have to be treated. The measurement of these low conductivities is very delicate. The method employed makes use of a direct current and gives reproducible results if care is taken to exclude interfering electric fields by screening the apparatus. (author) [French] Au cours de ce travail nous etudions plus particulierement deux points: l'obtention d'eau de haute purete et l'estimation de cette purete grace a la mesure de sa conductivite. En ce qui concerne la purification de l'eau nous constatons que la deionisation effectuee par les resines echangeuses d'ions en lits melanges conduit a l'obtention d'une eau de conductivite plus faible que celle recueillie par distillations. Mais cette faible conductivite, mesuree a l'abri de l'air immediatement a la sortie de la colonne, n'est pas stable. En effet, dans l

  6. Design of a safe facility for the metalorganic chemical vapor deposition of high-purity GaAs and AlGaAs

    Science.gov (United States)

    Messham, R. L.; Tucker, W. K.

    1986-09-01

    A metalorganic chemical vapor deposition (MOCVD) facility designed to safely handle highly toxic and pyrophoric growth materials is described. The system concept is based on remote operation, passive flow restriction, and forced air dilution to maintain safe gas concentrations under normal running and catastrophic system failure conditions. MOCVD is a key materials technology for advanced high-frequency optical and microwave devices. At this time, the use of highly toxic arsine as an arsenic source is dictated by critical device purity, reproducibility, and doping control requirements. The handling and use of this gas is a primary feature in the design of any safe facility for MOCVD growth of high-quality GaAs/AlGaAs. After a critical review of presently available effluent treatment techniques, it was concluded that a combination of flow restriction and dilution presented the most reliable treatment. Measured flow rates through orifices from 0.002 to 0.005 inch in diameter were compared to calculated values. A 0.002 inch orifice located in the cylinder valve or CGA fitting, combined with a cylinder of pure liquid arsine (205 psi), limits the maximum gas flow to ≪1 lpm. Such a flow can then be vented through a dedicated exhaust system where an additional forced injection of diluting air reduces the gas concentration to acceptable levels. In the final Westinghouse R&D Center design, the use of low-pressure pure arsine, flow restriction, and stack air injection has reduced the maximum stack exist gas concentration to below 25% of the IDLH level for arsine under total and catastrophic MOCVD facility equipment failure conditions. The elimination of potential problems with purging behind such orifices using carefully designed purging procedures and a microprocessor-controlled purging system are described. The IDLH level is defined by the OSHA and NIOSH standards completion program and represents the maximum level from which one could escape within 30 min without any

  7. 高纯度银杏黄酮的制备%Preparation of High-Purity Flavonoids from Ginkgo biloba L.

    Institute of Scientific and Technical Information of China (English)

    张伟; 李芊; 林炳昌

    2011-01-01

    [ Objective ] To prepare highly purified flavonoids of Ginkgo biloba L. , so as to explore a large - scale preparation process line of high purity flavonoids from Ginkgo biloba L.. [ Method ] Purified with chromatographic column with packing of ODS, effects of mobile phase ratio, concentration temperature and drying temperature on yield of flavonoids from Ginkgo biloba L. were investigated. [ Result] The optimum preparation conditions were as follows: target fraction of methanol to 0.5% phosphoric acid ratio of 5:5 and 7: 3, concentration temperature and drying temperature of 45 °C. The content of flavonoids from Ginkgo biloba L. was more than 90%, and the yield reached 78.3% under the optimal preparation process. [ Conclusion ] High-purily flavonoids from Ginkgo biloba L. were obtained, which provided an effective method for the preparation of highly purified Ginkgo biloba L. flavonoids.%[目的]制备高纯度的银杏黄酮,探索一条规模化制备高纯度银杏总黄酮的工艺路线.[方法]用固相填料为ODS的色谱柱纯化银杏黄酮,考察梯度洗脱、浓缩温度、干燥温度对银杏黄酮含量的影响.[结果]甲醇∶0.5%磷酸=5∶5和7∶3(V∶V)的馏分为目标馏分,最佳浓缩温度和干燥温度为45 ℃,在最佳条件下,银杏黄酮质量百分含量≥90%,收率为78.3%.[结论]该试验获得了高纯度银杏黄酮,为高纯度的银杏总黄酮制备提供了一种高效的方法.

  8. Development of high-throughput and high sensitivity capillary gel electrophoresis platform method for Western, Eastern, and Venezuelan equine encephalitis (WEVEE) virus like particles (VLPs) purity determination and characterization.

    Science.gov (United States)

    Gollapudi, Deepika; Wycuff, Diane L; Schwartz, Richard M; Cooper, Jonathan W; Cheng, K C

    2017-08-26

    In this paper, we describe development of a high-throughput, highly sensitive method based on Lab Chip CGE-SDS platform for purity determination and characterization of virus-like particle (VLP) vaccines. A capillary gel electrophoresis approach requiring about 41 s per sample for analysis and demonstrating sensitivity to protein initial concentrations as low as 20 μg/mL, this method has been used previously to evaluate monoclonal antibodies, but this application for lot release assay of VLPs using this platform is unique. The method was qualified and shown to be accurate for the quantitation of VLP purity. Assay repeatability was confirmed to be less than 2% relative standard deviation of the mean (% RSD) with interday precision less than 2% RSD. The assay can evaluate purified VLPs in a concentration range of 20-249 μg/mL for VEE and 20-250 μg/mL for EEE and WEE VLPs. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  9. Optimization of micro-strip gas chamber as two-dimensional neutron detector using gadolinium converter

    Energy Technology Data Exchange (ETDEWEB)

    Masaoka, Sei; Nakamura, Tatsuya; Yamagishi, Hideshi; Soyama, Kazuhiko [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    2002-02-01

    A micro-strip gas chamber (MSGC) has been developing as a two-dimensional position sensitive neutron detector for neutron scattering experiments using high-intensity pulsed-neutron source in a high-intensity proton accelerator facility. MSGC is required for the high count rate, high detective efficiency, high positional resolution, stabilization and covering large area. Our purpose in this paper is to verify the proper of Gadolinium as MSGC converter. First, the basic property of Gadolinium converter was examined by simple experiments using a zero-dimensional neutron detector on the purpose of deriving the detective efficiency. Second, the optimization of the arrangement of a capillary plate in MSGC has been done by simulation on the MSGC using Gadolinium converter. As a result of that, it has been proved that Gadolinium can be theoretically used as a converter of MSGC. (author)

  10. Sub-band gap photo-enhanced secondary electron emission from high-purity single-crystal chemical-vapor-deposited diamond

    Science.gov (United States)

    Yater, J. E.; Shaw, J. L.; Pate, B. B.; Feygelson, T. I.

    2016-02-01

    Secondary-electron-emission (SEE) current measured from high-purity, single-crystal (100) chemical-vapor-deposited diamond is found to increase when sub-band gap (3.06 eV) photons are incident on the hydrogenated surface. Although the light does not produce photoemission directly, the SEE current increases by more than a factor of 2 before saturating with increasing laser power. In energy distribution curves (EDCs), the emission peak shows a corresponding increase in intensity with increasing laser power. However, the emission-onset energy in the EDCs remains constant, indicating that the bands are pinned at the surface. On the other hand, changes are observed on the high-energy side of the distribution as the laser power increases, with a well-defined shoulder becoming more pronounced. From an analysis of this feature in the EDCs, it is deduced that upward band bending is present in the near-surface region during the SEE measurements and this band bending suppresses the SEE yield. However, sub-band gap photon illumination reduces the band bending and thereby increases the SEE current. Because the bands are pinned at the surface, we conclude that the changes in the band levels occur below the surface in the electron transport region. Sample heating produces similar effects as observed with sub-band gap photon illumination, namely, an increase in SEE current and a reduction in band bending. However, the upward band bending is not fully removed by either increasing laser power or temperature, and a minimum band bending of ˜0.8 eV is established in both cases. The sub-band gap photo-excitation mechanism is under further investigation, although it appears likely at present that defect or gap states play a role in the photo-enhanced SEE process. In the meantime, the study demonstrates the ability of visible light to modify the electronic properties of diamond and enhance the emission capabilities, which may have potential impact for diamond-based vacuum electron

  11. Co-Precipitation Synthesis of Gadolinium Aluminum Gallium Oxide (GAGG) via Different Precipitants

    Science.gov (United States)

    Sun, Yan; Yang, Shenghui; Zhang, Ye; Jiang, Jun; Jiang, Haochuan

    2014-02-01

    In order to obtain a uniform transparent ceramic scintillator, well-dispersed fine starting powders with high-purity, small grain size, spherical morphology and high sinter-ability are necessary. In this study, Ce3+ doped gadolinium aluminum gallium garnet Gd3Al3Ga2O12 (GAGG) powders were synthesized by the co-precipitation method. NH4OH, NH4HCO3 and the mixed solution of NH4OH and NH4HCO3 were used as precipitants, respectively. The precursor composition, phase formation process, microstructure, morphology, particle size distribution and luminescent properties of obtained GAGG powders were measured. The results show that powders prepared using the mixed precipitant exhibit the best microstructural morphology, good sinter-ability and highest luminescent intensity. Pure GAGG polycrystalline powders could be obtained at about 950°C for 1.5 h and the average size of the particles is about 50 nm. The photoluminescence spectrum shows a strong green-yellow emission near 540 nm.

  12. Purification of cerium, neodymium and gadolinium for low background experiments

    Directory of Open Access Journals (Sweden)

    Boiko R.S.

    2014-01-01

    Full Text Available Cerium, neodymium and gadolinium contain double beta active isotopes. The most interesting are 150Nd and 160Gd (promising for 0ν2β search, 136Ce (2β+ candidate with one of the highest Q2β. The main problem of compounds containing lanthanide elements is their high radioactive contamination by uranium, radium, actinium and thorium. The new generation 2β experiments require development of methods for a deep purification of lanthanides from the radioactive elements. A combination of physical and chemical methods was applied to purify cerium, neodymium and gadolinium. Liquid-liquid extraction technique was used to remove traces of Th and U from neodymium, gadolinium and for purification of cerium from Th, U, Ra and K. Co-precipitation and recrystallization methods were utilized for further reduction of the impurities. The radioactive contamination of the samples before and after the purification was tested by using ultra-low-background HPGe gamma spectrometry. As a result of the purification procedure the radioactive contamination of gadolinium oxide (a similar purification efficiency was reached also with cerium and neodymium oxides was decreased from 0.12 Bq/kg to 0.007 Bq/kg in 228Th, from 0.04 Bq/kg to <0.006 Bq/kg in 226Ra, and from 0.9 Bq/kg to 0.04 Bq/kg in 40K. The purification methods are much less efficient for chemically very similar radioactive elements like actinium, lanthanum and lutetium.

  13. Simultaneous Determination of Trace Rare Earth Elements and Other Elements in High Purity Terbium Oxide (Tb4O7) by ICP-AES After HPLC Separation Using P507 Resin

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    This article describes a new method for the simultaneous determination of trace rare earth elements (REEs) and non rare earth elements (NREEs) in high purity terbium oxide by ICP-AES after HPLC separation using P507 resin. The chromatographic separation of the analytes from the matrix using dilute nitric acid as mobile phase was studied. The experimental results showed that a favorable separation of trace metals (Cu and Gd) from the matrix (Tb) can easily be achieved by elution with dilute nitric acid within 25 min. The proposed method was applied to the determination of trace metals (Ca, Cu, Mg, Mn, Ni, Si, La, Ce, Pr, Nd, Sm, Eu and Gd) in high purity terbium oxide. The detection limits (DLs) for the analytes ranged from 0.4-4.0 μg\\5g-1, and the recoveries are from 78%-105%.

  14. Dopamine-containing gadolinium complex as magnetic resonance imaging contrast agent

    Institute of Scientific and Technical Information of China (English)

    ZHOU Xin; ZHAO Qi; YANG Lian; YAN Guoping; XU Wei; ZHOU Chengkai; ZHANG Qiao; LI Liang; LIU Fan; GUO Junfang

    2012-01-01

    Gadolinium diethylenetriamine-pentaacetic bisdopamide (Gd-DTPA-2DA) was synthesized by the incorporation of dopamine to diethylenetriaminepentaacetic acid (DTPA) and further reaction with gadolinium chloride.In vitro and in vivo properties were also evaluated.Gadolinium complex Gd-DTPA-2DA possessed higher relaxation effectiveness and less cytotoxicity to HeLa cells than that of Gd-DTPA.Moreover,Gd-DTPA-2DA greatly enhanced the contrast of MR images of the brains,provided prolonged intravascular duration,and produced highly contrasted visualization of the brain.

  15. Growth control in colon epithelial cells: gadolinium enhances calcium-mediated growth regulation.

    Science.gov (United States)

    Attili, Durga; Jenkins, Brian; Aslam, Muhammad Nadeem; Dame, Michael K; Varani, James

    2012-12-01

    Gadolinium, a member of the lanthanoid family of transition metals, interacts with calcium-binding sites on proteins and other biological molecules. The overall goal of the present investigation was to determine if gadolinium could enhance calcium-induced epithelial cell growth inhibition in the colon. Gadolinium at concentrations as low as 1-5 μM combined with calcium inhibits proliferation of human colonic epithelial cells more effectively than calcium alone. Gadolinium had no detectable effect on calcium-induced differentiation in the same cells based on change in cell morphology, induction of E-cadherin synthesis, and translocation of E-cadherin from the cytosol to the cell surface. When the colon epithelial cells were treated with gadolinium and then exposed to increased calcium concentrations, movement of extracellular calcium into the cell was suppressed. In contrast, gadolinium treatment had no effect on ionomycin-induced release of stored intracellular calcium into the cytoplasm. Whether these in vitro observations can be translated into an approach for reducing abnormal proliferation in the colonic mucosa (including polyp formation) is not known. These results do, however, provide an explanation for our recent findings that a multi-mineral supplement containing all of the naturally occurring lanthanoid metals including gadolinium are more effective than calcium alone in preventing colon polyp formation in mice on a high-fat diet.

  16. Analysis of the Purity of Cetrimide by Titrations

    DEFF Research Database (Denmark)

    Andersen, Jens Enevold Thaulov; Rasmussen, Claus/Dallerup; Nielsen, Hans/Boye

    2006-01-01

    The purity of cetrimide, trimethyl tetradecyl ammonium bromide (TTAB), that is an important preservative of many cosmetic and pharmaceutical products, was determined by three independent methods of titration. Traditionally, cetrimide was analysed by an assay method of the European Pharmacopoeia (Ph....... Eur.), which showed consistently a low purity of cetrimide with large standard deviations associated, however. A systematic 3% bias of the Ph. Eur. assay method was identified by comparing the result with results of two alternative methods of titration that exhibited high precision and high accuracy....... Titration by perchloric acid showed a 99.69 ± 0.05 % purity of cetrimide and titration by silver nitrate showed a 99.85% ± 0.05 % purity while the traditional assay method predicted a purity of only 97.1 ± 0.4. It was found that the discrepancy could be identified as differences in selectivity during...

  17. Couples Magnetic and Structural Transitions in High-Purity Dy and Gd5SbxGe4-x

    Energy Technology Data Exchange (ETDEWEB)

    Chernyshov, Alexander S. [Iowa State Univ., Ames, IA (United States)

    2006-01-01

    Magnetic materials exhibiting magnetic phase transitions simultaneously with structural rearrangements of their crystal lattices hold a promise for numerous applications including magnetic refrigeration, magnetomechanical devices and sensors. We undertook a detailed study of a single crystal of dysprosium metal, which is a classical example of a system where magnetic and crystallographic sublattices can be either coupled or decoupled from one another. Magnetocaloric effect, magnetization, ac magnetic susceptibility, and heat capacity of high purity single crystals of dysprosium have been investigated over broad temperature and magnetic field intervals with the magnetic field vector parallel to either the a- or c-axes of the crystal. Notable differences in the behavior of the physical properties when compared to Dy samples studied in the past have been observed between 110 K and 125 K, and between 178 K and ~210 K. A plausible mechanism based on the formation of antiferromagnetic clusters in the impure Dy has been suggested in order to explain the reduction of the magnetocaloric effect in the vicinity of the Neel point. Experimental and theoretical investigations of the influence of commensurability effects on the magnetic phase diagram and the value of the magnetocaloric effect have been conducted. The presence of newly found anomalies in the physical properties has been considered as evidence of previously unreported states of Dy. The refined magnetic phase diagram of dysprosium with the magnetic field vector parallel to the a-axis of a crystal has been constructed and discussed. The magnetic and crystallographic properties of Gd5SbxGe4-x pseudo-binary system were studied by x-ray diffraction (at room temperature), heat capacity, ac-magnetic susceptibility, and magnetization in the temperature interval 5-320 K in magnetic fields up to 100 kOe. The magnetic properties of three composition (x = 0.5, 1,2) were examined in detail. The

  18. The effect of environment on the creep deformation of ultra-high purity nickel-chromium-iron alloys at 360 degrees Celcius

    Science.gov (United States)

    Paraventi, Denise Jean

    2000-10-01

    Steam generators in pressurized water nuclear power plants have experienced significant problems with intergranular stress corrosion cracking (IGSCC) on the inner diameter of steam generator tubing for over 25 years. In the course of research to understand IGSCC, it has been shown that creep deformation may play a significant role in the cracking of commercial Alloy 600 (Ni-16Cr-9Fe-0.03C). The primary water environment can cause decreases in creep resistance (i.e., faster creep rates, shorter time to failure, and higher creep strains). During corrosion under the conditions of interest, both hydrogen reduction and metal dissolution occur. One or both may contribute to the enhancement of creep. The purpose of this work was to isolate the mechanism by which the water environment causes the creep deformation to increase. Activation area and activation enthalpy for glide were measured in argon and primary water on high purity Ni-16Cr-9Fe alloys. The results indicated that the activation area was reduced by primary water, consistent with a hydrogen enhanced plasticity mechanism for enhanced creep. The stress dependence of creep was also examined in argon and primary water. The results indicated that the internal stress of the alloy is reduced by the primary water environment. Lower internal stress is consistent with both a hydrogen model as well as a vacancy-aided climb model for enhanced creep. To isolate the effect of hydrogen on the creep of the alloy, experiments were conducted in a dissociated hydrogen environment. The results indicated that hydrogen would only increase the steady state creep rate if present before loading of the samples. However, if the sample was already in steady state creep and hydrogen introduced, a transient in the creep strain was observed. The creep rate returned to the original steady state rate in a short time. The results indicate that while hydrogen does affect the steady state creep to an extent, hydrogen cannot completely account for

  19. Self-assembled SnO2 micro- and nanosphere-based gas sensor thick films from an alkoxide-derived high purity aqueous colloid precursor

    Science.gov (United States)

    Kelp, G.; Tätte, T.; Pikker, S.; Mändar, H.; Rozhin, A. G.; Rauwel, P.; Vanetsev, A. S.; Gerst, A.; Merisalu, M.; Mäeorg, U.; Natali, M.; Persson, I.; Kessler, V. G.

    2016-03-01

    Tin oxide is considered to be one of the most promising semiconductor oxide materials for use as a gas sensor. However, a simple route for the controllable build-up of nanostructured, sufficiently pure and hierarchical SnO2 structures for gas sensor applications is still a challenge. In the current work, an aqueous SnO2 nanoparticulate precursor sol, which is free of organic contaminants and sorbed ions and is fully stable over time, was prepared in a highly reproducible manner from an alkoxide Sn(OR)4 just by mixing it with a large excess of pure neutral water. The precursor is formed as a separate liquid phase. The structure and purity of the precursor is revealed using XRD, SAXS, EXAFS, HRTEM imaging, FTIR, and XRF analysis. An unconventional approach for the estimation of the particle size based on the quantification of the Sn-Sn contacts in the structure was developed using EXAFS spectroscopy and verified using HRTEM. To construct sensors with a hierarchical 3D structure, we employed an unusual emulsification technique not involving any additives or surfactants, using simply the extraction of the liquid phase, water, with the help of dry butanol under ambient conditions. The originally generated crystalline but yet highly reactive nanoparticles form relatively uniform spheres through self-assembly and solidify instantly. The spheres floating in butanol were left to deposit on the surface of quartz plates bearing sputtered gold electrodes, producing ready-for-use gas sensors in the form of ca. 50 μm thick sphere-based-films. The films were dried for 24 h and calcined at 300 °C in air before use. The gas sensitivity of the structures was tested in the temperature range of 150-400 °C. The materials showed a very quickly emerging and reversible (20-30 times) increase in electrical conductivity as a response to exposure to air containing 100 ppm of H2 or CO and short (10 s) recovery times when the gas flow was stopped.Tin oxide is considered to be one of the

  20. Electronic Structure of Gadolinium Calcium Oxoborate

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, A; Adams, J; Schaffers, K

    2004-07-01

    Gadolinium calcium oxoborate (GdCOB) is a nonlinear optical material that belongs to the calcium--rare-earth (R) oxoborate family, with general composition Ca{sub 4}RO(BO{sub 3}){sub 3} (R{sup 3+} = La, Sm, Gd, Lu, Y). X-ray photoemission was applied to study the valence band electronic structure and surface chemistry of this material. High resolution photoemission measurements on the valence band electronic structure and Gd 3d and 4d, Ca 2p, B 1s and O 1s core lines were used to evaluate the surface and near surface chemistry. These results provide measurements of the valence band electronic structure and surface chemistry of this rare-earth oxoborate.

  1. Removal of gadolinium nitrate from heavy water

    Energy Technology Data Exchange (ETDEWEB)

    Wilde, E.W.

    2000-03-22

    Work was conducted to develop a cost-effective process to purify 181 55-gallon drums containing spent heavy water moderator (D2O) contaminated with high concentrations of gadolinium nitrate, a chemical used as a neutron poison during former nuclear reactor operations at the Savannah River Site (SRS). These drums also contain low level radioactive contamination, including tritium, which complicates treatment options. Presently, the drums of degraded moderator are being stored on site. It was suggested that a process utilizing biological mechanisms could potentially lower the total cost of heavy water purification by allowing the use of smaller equipment with less product loss and a reduction in the quantity of secondary waste materials produced by the current baseline process (ion exchange).

  2. High-k gadolinium scandate on Si obtained by high pressure sputtering from metal targets and in-situ plasma oxidation

    Science.gov (United States)

    Pampillón, M. A.; San Andrés, E.; Feijoo, P. C.; Fierro, J. L. G.

    2017-03-01

    This article studies the physical and electrical behavior of Gd2‑x Sc x O3 layers grown by high pressure sputtering from metallic Gd and Sc targets. The aim is to obtain a high permittivity dielectric for microelectronic applications. The films were obtained by the deposition of a metallic nanolaminate of Gd and Sc alternating layers, which is afterwards in-situ oxidized by plasma. The oxide films obtained were close to stoichiometry, amorphous and with minimal interfacial regrowth. By fabricating metal–insulator–semiconductor capacitors we found that a moderate temperature annealing is needed to enhance permittivity, which reaches a high value of 32 while keeping moderate leakage. Finally, the feasibility of interface scavenging in this material with Ti gate electrodes is also demonstrated.

  3. mu. /sup +/ diffusion and trapping in high purity and oxygen-doped Nb. [Temperature dependence, 10 to 120/sup 0/K, impurity-associated traps

    Energy Technology Data Exchange (ETDEWEB)

    Brown, J.A.; Heffner, R.H.; Leon, M.; Parkin, D.M.; Schillaci, M.E.; Gauster, W.B.; Fiory, A.T.; Kossler, W.J.; Birnbaum, H.K.; Denison, A.B.; Cooke, D.W.

    1978-01-01

    Data are presented for the temperature dependence of the muon depolarization rate between 10 and 120 K for three samples of niobium of varying purity. Two samples, each containing approximately 200 ppM substitutional Ta and interstitial concentrations of 10 ppM and 560 ppM (mostly O), respectively, were studied. A third sample containing only 3 ppM Ta and an estimated 10 ppM total interstitial impurities was also measured. The results indicate that even at the lowest temperatures studied the depolarization of the muon is dominated by traps associated with impurities. 9 references.

  4. Purity of targets prepared on Cu substrates

    Science.gov (United States)

    Méens, A.; Rossini, I.; Sens, J. C.

    1993-09-01

    The purity of several elemental self-supporting targets usually prepared by evaporation onto soluble Cu substrates has been studied. The targets were analysed by Rutherford backscattering and instrumental neutron activation analysis. Because of the high percentage of Cu observed in some Si targets, further measurements, including transmission electron microscopy, have been performed on Si targets deposited by e-gun bombardment onto Cu and ion-beam sputtering onto betaine.

  5. Analysis of Rare Earth Elements (REE) in vein quartz and quartz-sandstone host rock in the Zhelannoe high purity quartz deposit, Russia

    Science.gov (United States)

    Zemskova, Marina; Prokofiev, Vsevolod; Bychkov, Andrey

    2015-04-01

    The Zhelannoe high purity quartz deposit is located on the western slope of the Polar Urals. It is one of the largest deposits of vein quartz and rock crystal in Russia. Most of the mineralization is hosted within a single horizon of very firm quartz-sandstone, where plastic deformation did not occur almost entirely. All tectonic stress was released by the development of numerous thrust faults of different scales. Cavities formed during this process were later filled with quartz and rock crystal. In order to obtain more details on conditions under which mineralization took place, analysis of trace element contents in vein quartz and host rocks, and the micro-thermometric study of fluid inclusions in quartz have been carried out. The trace element composition of vein quartz and of the host rock has been determined by ICP-MS. The results have shown that concentrations of most of the 46 studied elements in quartz are two orders of magnitude lower than in chondrite, and more than three orders of magnitude lower than in the upper crust. Even though Pb and Li have the highest concentrations in quartz samples, levels are only nearly comparable in chondrite, and substantially lower in the upper crust. At the same time, negative anomalies of Pb and Li concentrations in the host rock may indicate the removal of these elements during vein quartz formation. Contents of most REEs are two orders of magnitude lower than in chondrite, and three orders of magnitude lower than in the host rock. Generally, the patterns of REE distribution in vein quartz and the host rock express a clear correlation; confirming the genetic link between vein quartz and quartz-sandstone host rock. However, the process of quartz recrystallization led to an intense decrease of REEs content, and of all other impurities, which consequently influenced industrial value of the Zhelannoe deposit. As a result of the micro-thermometric study of fluid inclusions in quartz, the following physical

  6. [Separation with ion exchange fiber column and determination of La, Nd, Eu and Gd in high purity ytterbium oxide by ICP-AES].

    Science.gov (United States)

    Gong, Qi; Chen, Jie; Ji, Ri-Wen; Pan, Xue-Zhen; Wu, Juan

    2010-02-01

    In the present paper, trace La, Nd, Eu and Gd were separated and enriched with strong acid ion exchange fiber column from high purity Yb2 O3, and then determined by Optima 5 300 DV ICP-AES. The ion exchange fiber's breakthrough capacity for Yb was 134 mg x g(-1). The separation condition using 4.0 g fiber column was that after the test solution (pH = 3.0) was fed into the ion exchange fiber column at 1.0 mL x min(-1), the column was pre--leached by dilute nitric acid (pH = 3.00) of 80 mL at 1.5 mL x min(-1) at first, and then was eluted by 0.01 mol x L(-1) ammonium EDTA (pH = 5.00) at the same flow rate. The results showed that 10 mg Yb could reach the baseline separation with 0.100 microg of the four rare earth impurities, and after 100 mg Yb in feed solution had been separated, only 0.017 1 microg x mL(-1) Yb remained in the impurities enriched effluent. When the concentration of Yb2 O3 is less than 100 microg x mL(-1) (87.8 microg x mL(-1) Yb), the matrix interference from Yb on with determination of La, Nd, Eu and Gd can be neglected. The enrichment factors were 3.68 x 10(5) for La2 O3, 4.20 x 10(5) for Nds O3, 3.82 x 10(5) for Eu2 O3, and 4.01 x 10(5) for Gd2 O3, and the detection limits of the method were 0.005 0, 0.014, 0.001 8 and 0.008 2 pg x mL(-1) for La2 O3, Nd2 O3, Eu2 O3 and Gd2 O3 respectively. The proposed method was applied to the analysis of 99.99% Yb2 O3 with RSD (%, n = 5) of 6.2, 5.9, 7.3 and 2.5 for La2 O3, Nd2 O3, Eu2 O3 and Gd2 O3 respectively, and the average recoveries of standard addition were 94.2%, 107%, 97.8% and 102% for La2 O3, Nd2 O3, Eu2 O3 and Gd2 O3 respectively. The calibration curve did not need matrix matching with Yb, and the analysis period was within 4 hour.

  7. New variable selection method using interval segmentation purity with application to blockwise kernel transform support vector machine classification of high-dimensional microarray data.

    Science.gov (United States)

    Tang, Li-Juan; Du, Wen; Fu, Hai-Yan; Jiang, Jian-Hui; Wu, Hai-Long; Shen, Guo-Li; Yu, Ru-Qin

    2009-08-01

    One problem with discriminant analysis of microarray data is representation of each sample by a large number of genes that are possibly irrelevant, insignificant, or redundant. Methods of variable selection are, therefore, of great significance in microarray data analysis. A new method for key gene selection has been proposed on the basis of interval segmentation purity that is defined as the purity of samples belonging to a certain class in intervals segmented by a mode search algorithm. This method identifies key variables most discriminative for each class, which offers possibility of unraveling the biological implication of selected genes. A salient advantage of the new strategy over existing methods is the capability of selecting genes that, though possibly exhibit a multimodal distribution, are the most discriminative for the classes of interest, considering that the expression levels of some genes may reflect systematic difference in within-class samples derived from different pathogenic mechanisms. On the basis of the key genes selected for individual classes, a support vector machine with block-wise kernel transform is developed for the classification of different classes. The combination of the proposed gene mining approach with support vector machine is demonstrated in cancer classification using two public data sets. The results reveal that significant genes have been identified for each class, and the classification model shows satisfactory performance in training and prediction for both data sets.

  8. Study on gadolinium complexes based on polysaccharide derivatives as a contrast agent for MRI

    Energy Technology Data Exchange (ETDEWEB)

    Hashiguchi, Yuji; Seri, Shigemi; Kubomura, Kan; Abe, Yukiko; Kamimura, Kenji; Fujimoto, Chieko; Iguchi, Toshio; Iwai, Kumiko (Nihon Medi-Physics Co., Ltd., Sodegaura, Chiba (Japan))

    1993-05-01

    The authors report new gadolinium compounds, polysaccharide-gadolinium chelate, that have the enhancement property in magnetic resonance imaging (MRI) as well as a longer half-life time in blood. Dialdehyde starch (DAS ; mol. wt. 7 x 10[sup 3]) and dialdehyde amylose (DAA ; mol. wt. 3 x 10[sup 3]) were synthesized to increase the half-life time in blood. The binding of gadolinium to DAS or DAA was facilitated by the newly synthesized bifunctional chelating agents N-[2-bis(carboxymethyl)aminoethyl] -N-[2-bis(carboxymethyl)amino -2(p-benzyl)ethyl]glycine (ABDTPA) and 10-[N-(2-aminoethyl)carbamoyl]methyl-[alpha], [alpha]', [alpha]''-trimethyl-1,4,7,10 -tetraazacyclododecane-1,4,7-triacetic acid (DO 3 MA). The enhancement properties of resulting gadolinium compounds were evaluated for biodistribution, relaxivity and enhancement effect. Biodistribution was examined by use of [sup 111]In labelled complex. Relaxivity was measured at 0.5T and 1.5T. Enhancement effect was examined in vivo by using rats that have brain occlusions. Gadolinium(Gd) complexes with DAS or DAA were found to be staying in the blood vessel for a longer period of time than other existing enhancers. The half-life time of DAS-ABDTPA-Gd is 2h, while as DAA-ABDTPA-Gd is 55 min, eighty to ninety percent of gadolinium complexes bound to DAS or DAA were excreted in urine 24 h after administration. Relaxivities of the above gadolinium complexes were 1.2[approx]2 times as high as those of ABDTPA-Gd or DO 3 MA-Gd. These results demonstrate that gadolinium complexes based on polysaccharide derivatives are promising compounds for future use as MRI enhancers. (author).

  9. PREPARATION OF EPA AND DHA ESTERS WITH HIGH PURITY BY SUPERCRITICAL CO2 EXTRACTION AND RECTIFICATION%超临界CO2萃取精馏制取高纯度EPA乙酯和DHA乙酯

    Institute of Scientific and Technical Information of China (English)

    邱榕; 范维澄; 陈钧

    2001-01-01

    Fish oil ethyl esters complexed with aqueous silver nitrate solution were extracted and rectified by supercritical CO2 to obtain DHA ester and EPA ester with high purity. The effects of some independent variables,such as extraction pressure, temperature gradient of rectifying column and programmed pressure,on rectification were investigated.The results showed that programmed pressure is suitable for purification of EPA and DHA esters. Increase of column temperature gradient from bottom to top is one of the key elements in rectification. Furthermore, higher temperature gradient leads to better separation effect.

  10. Recovery of high purity silicon from SoG crystalline silicon cutting slurry waste%太阳能晶体硅切割废料中高纯硅的提取

    Institute of Scientific and Technical Information of China (English)

    李大刚; 邢鹏飞; 庄艳歆; 李峰; 涂赣峰

    2014-01-01

    The recovery of high-purity Si from the cutting slurry waste of SoG-Si was investigated. The composition and size distribution of cutting waste were characterized. The Si-rich powders were obtained from the cutting waste using a physical sedimentation process, and then further purified by removing impurity using acid leaching. The effects of process parameters such as acid leaching time, temperature and the ratio of solid to liquid on the purification efficiency were investigated, and the parameters were optimized. Afterwards, the high-purity Si ingot was obtained by melting the Si-rich powders in vacuum furnace. Finally, the high purity Si with 99.96%Si, 1.1×10-6 boron (B), and 4.0×10-6 phosphorus (P) were obtained. The results indicate that it is feasible to extract high-purity Si, and further produce SoG-Si from the cutting slurry waste.%研究从太阳能晶体硅切割废料中制取高纯硅。分析切割废料的组成、粒度分布等,利用物理沉降法对废料中的硅粉进行富集,然后经酸洗除杂。研究酸洗工艺参数如酸洗时间、温度、固液比等对提纯效率的影响,并优化工艺参数。最后将酸洗除杂的硅富集料进行真空高温熔炼获得含99.96%Si、1.1×10-6B及4.0×10-6 P(质量分数)的高纯硅。结果表明:从晶体硅切割废料中回收太阳能多晶硅是未来的一个重要发展方向。

  11. The Liquid Argon Purity Demonstrator

    CERN Document Server

    Adamowski, M; Dvorak, E; Hahn, A; Jaskierny, W; Johnson, C; Jostlein, H; Kendziora, C; Lockwitz, S; Pahlka, B; Plunkett, R; Pordes, S; Rebel, B; Schmitt, R; Stancari, M; Tope, T; Voirin, E; Yang, T

    2014-01-01

    The Liquid Argon Purity Demonstrator was an R&D test stand designed to determine if electron drift lifetimes adequate for large neutrino detectors could be achieved without first evacuating the cryostat. We describe here the cryogenic system, its operations, and the apparatus used to determine the contaminant levels in the argon and to measure the electron drift lifetime. The liquid purity obtained by this system was facilitated by a gaseous argon purge. Additionally, gaseous impurities from the ullage were prevented from entering the liquid at the gas-liquid interface by condensing the gas and filtering the resulting liquid before returning to the cryostat. The measured electron drift lifetime in this test was greater than 6 ms, sustained over several periods of many weeks. Measurements of the temperature profile in the argon, to assess convective flow and boiling, were also made and are compared to simulation.

  12. The Liquid Argon Purity Demonstrator

    Energy Technology Data Exchange (ETDEWEB)

    Adamowski, M.; Carls, B.; Dvorak, E.; Hahn, A.; Jaskierny, W.; Johnson, C.; Jostlein, H.; Kendziora, C.; Lockwitz, S.; Pahlka, B.; Plunkett, R.; Pordes, S.; Rebel, B.; Schmitt, R.; Stancari, M.; Tope, T.; Voirin, E.; Yang, T.

    2014-07-01

    The Liquid Argon Purity Demonstrator was an R&D test stand designed to determine if electron drift lifetimes adequate for large neutrino detectors could be achieved without first evacuating the cryostat. We describe here the cryogenic system, its operations, and the apparatus used to determine the contaminant levels in the argon and to measure the electron drift lifetime. The liquid purity obtained by this system was facilitated by a gaseous argon purge. Additionally, gaseous impurities from the ullage were prevented from entering the liquid at the gas-liquid interface by condensing the gas and filtering the resulting liquid before returning to the cryostat. The measured electron drift lifetime in this test was greater than 6 ms, sustained over several periods of many weeks. Measurements of the temperature profile in the argon, to assess convective flow and boiling, were also made and are compared to simulation.

  13. Purity homophily in social networks.

    Science.gov (United States)

    Dehghani, Morteza; Johnson, Kate; Hoover, Joe; Sagi, Eyal; Garten, Justin; Parmar, Niki Jitendra; Vaisey, Stephen; Iliev, Rumen; Graham, Jesse

    2016-03-01

    Does sharing moral values encourage people to connect and form communities? The importance of moral homophily (love of same) has been recognized by social scientists, but the types of moral similarities that drive this phenomenon are still unknown. Using both large-scale, observational social-media analyses and behavioral lab experiments, the authors investigated which types of moral similarities influence tie formations. Analysis of a corpus of over 700,000 tweets revealed that the distance between 2 people in a social-network can be predicted based on differences in the moral purity content-but not other moral content-of their messages. The authors replicated this finding by experimentally manipulating perceived moral difference (Study 2) and similarity (Study 3) in the lab and demonstrating that purity differences play a significant role in social distancing. These results indicate that social network processes reflect moral selection, and both online and offline differences in moral purity concerns are particularly predictive of social distance. This research is an attempt to study morality indirectly using an observational big-data study complemented with 2 confirmatory behavioral experiments carried out using traditional social-psychology methodology.

  14. 高纯锆英石湿法超细磨矿工艺参数的研究%STUDY ON WET GRINDING PARAMETERS FOR PRODUCING ULTRAFINE ZIRCON WITH HIGH PURITY

    Institute of Scientific and Technical Information of China (English)

    杨久流; 罗家珂

    2001-01-01

    Ultrafine zircon powder with high purity is a kind of brightening agent in glaze for making high-grade cleaning whiteware. Wet ultrafine grinding is the key operation for producing ultrafine zircon power with high purity, and directly affects the size distribution, d50 and whiteness of the final products. This paper lays emphasis on researching wet grinding process parameters for producing ultrafine zircon power, such as the weight ratio of ball to feed material, grinding density and time, and weight assignment with different ball sizes, and their effects on quality of zircon power.%高纯超细锆英石粉是制造高档卫生洁具陶瓷所用釉料中的乳浊增白剂。湿法超细磨矿是生产高纯超细锆英石粉的关键工序之一,它直接影响最终产品粒度分布、中位粒径和白度。本文着重研究锆英石超细磨矿工艺参数球料比、磨矿浓度、磨矿时间及磨矿介质球径的配比等对锆英石微粉产品质量的影响。

  15. Type of MRI contrast, tissue gadolinium, and fibrosis.

    Science.gov (United States)

    Do, Catherine; Barnes, Jeffrey L; Tan, Chunyan; Wagner, Brent

    2014-10-01

    It has been presupposed that the thermodynamic stability constant (K(therm)) of gadolinium-based MRI chelates relate to the risk of precipitating nephrogenic systemic fibrosis. The present study compared low-K(therm) gadodiamide with high-K(therm) gadoteridol in cultured fibroblasts and rats with uninephrectomies. Gadolinium content was assessed using scanning electron microscopy equipped with energy-dispersive X-ray spectroscopy in paraffin-embedded tissues. In vitro, fibroblasts demonstrated dose-dependent fibronectin generation, transforming growth factor-β production, and expression of activated myofibroblast stress fiber protein α-smooth muscle actin. There were negligible differences with respect to toxicity or proliferation between the two contrast agents. In the rodent model, gadodiamide treatment led to greater skin fibrosis and dermal cellularity than gadoteridol. In the kidney, both contrast agents led to proximal tubule vacuolization and increased fibronectin accumulation. Despite large detectable gadolinium signals in the spleen, skin, muscle, and liver from the gadodiamide-treated group, contrast-induced fibrosis appeared to be limited to the skin and kidney. These findings support the hypothesis that low-K(therm) chelates have a greater propensity to elicit nephrogenic systemic fibrosis and demonstrate that certain tissues are resistant to these effects.

  16. Challenges of the management of severe hemophilia A with inhibitors: two case reports emphasizing the potential interest of a high-purity human Factor VIII/von Willebrand factor concentrate and individually tailored prophylaxis guided by thrombin-generation test.

    Science.gov (United States)

    Mathieu, Sophie; Crampe, Carine; Dargaud, Yesim; Lavigne-Lissalde, Géraldine; Escuriola-Ettingshausen, Carmen; Tardy, Brigitte; Meley, Roland; Thouvenin, Sandrine; Stephan, Jean L; Berger, Claire

    2015-12-01

    Severe hemophilia A is an X-linked bleeding disorder. Immune tolerance induction (ITI) is the best strategy of treatment when patients develop inhibitors. The objective is to illustrate the benefit of a high-purity human factor VIII/von Willebrand factor (VWF) concentrate (Octanate) in the management of ITI. We also wanted to raise the potential interest of laboratory assays such as thrombin-generation test (TGT) and epitope mapping. Two patients were treated during ITI, first with a recombinant FVIII and then with plasma-derived factor VIII without success, and, finally, with Octanate. Bypassing agents were used based on the results of TGT. Epitope mapping was performed during ITI therapy. These observations suggest the potential contribution of Octanate in the management of ITI in difficult cases. The use of bypassing agents can be necessary in prophylaxis or to treat bleedings, and may be guided by TGT results. Epitope mapping is used to describe the inhibitor. This article shows a decrease of the inhibitor directed against the C2 domain after initiation of Octanate. A high-purity human factor VIII/von Willebrand factor concentrate (Octanate) may be a valuable therapeutical option for ITI therapy. TGT and epitope mapping could be of help in the management of ITI.

  17. 采用ICP-AES测定高纯氢氧化钠中Ca、Al、Si的含量%Using ICP-AES to determine the concentration of Ca, Al and Si in high-purity sodium hydroxide

    Institute of Scientific and Technical Information of China (English)

    丁珺

    2012-01-01

    介绍了等离子体原子发射光谱,采用标准加入法测定高纯氢氧化钠中痕量Ca、Al、Si含量的方法,该方法的准确度和精密度都符合定量要求。目前,该方法已应用于高纯氢氧化钠中杂质氧化钙、氧化铝、氧化硅含量的测定,且具有操作简便、省时、省材和高灵敏度等特点,适用于批量样品的测定。%This report introduces a novel method to determine the concentration of trace impurities in high- purity sodium hydroxide. The method uses ICP-AES combined with standard addition, thus its accuracy and precision fits the requirement of quantitative measurement. This method has been successfully applied to determine the concentration of calcium oxide (CaO), aluminum oxide (A1203) and silicon dioxide (SiO2) in high-purity sodium hydroxide. The method is not only convenient, fast but also very sensitive, therefore is suitable for batch analysis.

  18. Microwave and optical diagnostics in a gadolinium plasma; Diagnostics hyperfrequence et optique dans un plasma magnetise de gadolinium

    Energy Technology Data Exchange (ETDEWEB)

    Larousse, B. [CEA Centre d`Etudes de Saclay, 91 - Gif-sur-Yvette (France). Dept. des Procedes d`Enrichissement]|[Conservatoire National des Arts et Metiers (CNAM), 75 - Paris (France)

    1997-12-31

    The optimization of the separation process of the gadolinium isotopes by Ion Cyclotron Resonance requires a precise knowledge of the physical characteristics of the plasma. Thus, two kinds of diagnostics have been developed: the first one to estimate the microwave power inside the source and the second one to measure the density of atomic and ionic of the gadolinium inside the plasma source and in front of the collector. Microwave diagnostic: A microstrip antenna has been designed and developed in order to characterize the microwave at 36 GHz frequency in the plasma source. The experimental results for different plasma regimes are presented. The measurements inside the plasma source show a maximum of microwave absorption for an argon pressure of 10{sup -4} mb (93% of absorption of the incident wave in the conditions of isotope separation). Laser absorption diagnostic: The theory of laser absorption in presence of a magnetic field is recalled and the first results are presented. In the spectral range between 560 and 620 nm, corresponding to high energy levels of gadolinium, no signal is obtained so that the density is below the detection limit 10{sup 10} cm{sup -3}. In the spectral range between 380 and 400 nm, two lines are observed, issue from the fundamental and metastable (633 cm{sup -1}) levels. The density of metastable level of gadolinium ions is about 10{sup 10} cm{sup -3} with a relative precision of 15 % and its variation is studied as a function of argon pressure, at different sections of the plasma column (source, collector). The achieved set of measurements has been performed in order to check the theoretical models. (author) 32 refs.

  19. 尿素柱层析结合重结晶制备高纯度茄尼醇%Preparation of High-purity Solanesol by Urea Column Chromatography Combining with Recrystallization

    Institute of Scientific and Technical Information of China (English)

    韩蕊蕊; 吕纯洁; 邓天昇; 刘旭光; 侯相林

    2012-01-01

    为制备高纯度的茄尼醇,进行了尿素柱层析结合重结晶分离茄尼醇试验,考察了尿素柱层析固定相尿素与硅胶的比例、洗脱溶剂、上样量对茄尼醇纯度和收率的影响.结果表明:尿素柱层析固定相尿素与硅胶质量比1∶1,洗脱剂石油醚与乙酸乙酯体积比60∶1,上样量0.4 g,茄尼醇的纯度和收率分别为74.8%和89.8%.再经过甲醇、乙腈各结晶一次,茄尼醇的纯度达96.7%,总收率0.1248%.该方法可以用于浸膏中茄尼醇的精制.%To obtain high-purity solanesol, an experiment on the refinement of solanesol by urea column chromatography combining with recrystallization was conducted. The influences of ratio of urea to silica gel in stationary phase, elution solvent and the sample loading in urea column chromatography on the purity and yield of solanesol were investigated. The results showed that when the mass ratio of urea to silica gel in stationary phase was 1:1 (w/w), the proportion of petroleum ether to ethyl acetate in elution solvent was 60:1 (v/v), the sample loading was 0.4 g, the purity and yield of solanesol reached 74.8% and 89.8% , respectively. The resultant solanesol was recrystalized in methanol and acetonitrile sequentially, and a white crystalline solanesol was obtained with purity of 96.7% and yield of 0.1248%.

  20. 高纯菜籽蛋白的制备及其相关性质研究%Study on preparation of high-purity rapeseed protein and its properties

    Institute of Scientific and Technical Information of China (English)

    周俊; 潘丽军; 韩智宏

    2012-01-01

    Protein was extracted from coldpressed rapeseed meal which was detoxicated firstly,then the extract was ultrafiltered to obtain high-purity rapeseed protein,chemical components,amino acid and function of proteins were also studied.Extraction rate of protein from rapeseed meal after detoxication was 67.97%,rapeseed protein of different purity from 70% to 90% could be prepared by ultrafiltration.Phytic acid,glucosinolate were not detected in proteins,and content of polyphenol was decreased obviously with rise of protein purity.Sulphur-containing amino acid(Methionine+Cysteine) was the first limiting amino acid.Chemical scores of the other essential amino acids were higher than FAO/WHO standard,but most were inferior to standard of whole egg protein.Capacities of water-holding,fat-absorbing,emulsion,emulsion stability,foaming and foam stability correlated positively with purity of rapeseed protein.%对脱毒后的冷榨菜籽粕进行蛋白提取,超滤纯化提取液获得高纯度的蛋白成品,并研究分析了蛋白的成分、氨基酸及其功能特性。脱毒后菜籽粕中蛋白提取率为67.97%,超滤后蛋白纯度可达70%~90%。成品蛋白中植酸与硫苷未检出,多酚含量随蛋白纯度增加而显著下降,甲硫氨酸+半胱氨酸是第一限制性氨基酸,其余必需氨基酸化学评分均高于FAO/WHO标准,却大多低于全蛋蛋白标准。菜籽蛋白的持水性、吸油性、乳化性及乳化稳定性、起泡性及起泡稳定性均与蛋白纯度呈正相关。

  1. Effect of gadolinium on aged hardening behavior,microstructure and mechanical properties of Mg-Nd-Zn-Zr alloy

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Mg-3.4Nd-0.1 Zn-0.40Zr alloy samples with and without containing gadolinium(0.6%,mass fraction)were prepared by sand casting.The aged hardening behavior,solidification microstructures and mechanical properties of the alloys were investigated by using the analysis methods of OM,XRD,TEM,hardness tests and mechanical property tests.The main research results are as follows.1)Compared with the alloy without the addition of gadolinium.the alloys with the addition of gadolinium shows the more remarkable age-hardening response.2) The as-cast microstructure of the alloy with and without containing gadolinium consists of α-Mg grains with Mg12Nd phase on the grain boundary.After solution heat-treatment,Mg12Nd phase of the alloy without containing gadolinium is dissolved in the matrix,however,there iS still discontinued Mg12Nd phase at grain boundary of the alloy with containing gadolinium.The more finely dispersed precipitates in Mg matrix are formed in the alloy with containing gadolinium during age-treatment.3)The room temperature and high temperature mechanical properties ofthe alloy are satisfactory.with σb=280 MPa,σ0.2=165 MPa at RT and aσb=215 MPa,σ0.2=155 MPa at 250℃.The high temperature mechanical properties decrease slightly with the increase of temperature.

  2. Síntese e caracterização de precursores de cério de alta pureza Synthesis and characterization of high purity cerium precursors

    Directory of Open Access Journals (Sweden)

    C. A. S. Queiroz

    2001-03-01

    Full Text Available Neste trabalho são destacadas as técnicas de separação e de purificação de terras raras por precipitação fracionada e troca iônica, além das técnicas usualmente utilizadas no controle analítico destes materiais. A aplicação destas técnicas é mostrada neste trabalho para a obtenção de óxido ou nitrato de cério com pureza > 99%. O principal objetivo é a obtenção de precursores à base de cério para o processamento de cerâmicas de zircônia-céria ou céria contendo terras raras. A disponibilidade de cloretos mistos, matéria-prima para a preparação de terras raras individuais, e o conhecimento das técnicas de separação, purificação e controle analítico de terras raras no IPEN, permite sua obtenção local para uso em pesquisa e desenvolvimento.In this work techniques of fractioned precipitation and ion exchange for separating and purifying rare earth elements are outlined. Other techniques usually utilized in the analytical control of these elements are also briefly discussed. The application of these techniques for the preparation of cerium nitrate or cerium oxide of > 99% purity are demonstrated. The main purpose is to obtain cerium precursors for the processing of zirconia-ceria or ceria-rare earth ceramic materials. The raw material availability in the form of mixed chlorides, and the knowledge of these techniques at IPEN allows for obtaining these precursors in the local market for research and development purposes.

  3. 由铵盐制备高纯氟化钡的工艺研究%Preparation technology of high purity barium fluoride from ammonium salt

    Institute of Scientific and Technical Information of China (English)

    许春晓; 刘晓红; 柯春兰; 章小明

    2011-01-01

    以氟化铵和氯化钡为原料,采用沉淀法制备了氟化钡.反应温度为25℃,反应时间为60min,氯化钡初始质量分数为10%,氟化铵与氯化钡物质的量比为2.2,m(洗水):m(滤饼)=10:1,可制备出纯度达99%以上的氟化钡.XRD谱图表明,样品氟化钡的所有衍射峰均与标准立方相氟化钡吻合,属立方晶系.该工艺流程简单,经济效益好.%Barium fluoride (BaF2 ) was prepared by precipitation method with ammonium fluoride and barium chloride as raw materials. BaF2 with purity of more than 99% can be prepared when reaction temperature is 25 ℃ ,reaction time is 60 rnin,initial mass fraction of barium chloride is 10% ,amount-of-substance ratio of ammonium fluoride to barium chloride is 2.2,and the mass ratio of washing water amount to filter cake amount = 10: 1. XRD pattern showed that all the diffraction peaks of barium fluoride sample were consistent with the standard cubic barium fluoride. Therefore it belongs to the cubic crystal system. The technology has short flow route and good economic benefits.

  4. UV Active Diluent High Purity Tripropylene Glycol Diacrylate(TPGDA) and Its UV Coatings%UV活性稀释剂高纯二缩三丙二醇二丙烯酸酯及其UV涂料

    Institute of Scientific and Technical Information of China (English)

    胡剑飞; 付鹏志; 马怀详; 桑卫东

    2012-01-01

    Intermediate was prepared via the ring-opening polymerization in the presence of catalyst and 1,2-propylene glycol and propylene oxide used as raw materials, the intermediate as separated by a special rectifying process, the tripropylene glycol of over 98% purity was obtained. Finally, high purity TPGDA was synthesized by esterifieation with acrylic acid. The ester distribution of tripropylene glycol diacrylate before and after purifying the tripropylene glycol and performance difference in their application of UV coatings was systematic analyzed.%1,2-丙二醇、环氧丙烷在催化剂的作用下进行开环聚合反应得中间体,再对中间体采用特殊精馏方式进行组分分离,得到纯度达98%以上的二缩三丙二醇,然后经丙烯酸酯化得高纯TPGDA。系统分析二缩三丙二醇提纯前及提纯后所合成的光固化单体二缩三丙二醇二丙烯酸酯(TPGDA)的酯分布及其在UV涂料应用中的性能差异。

  5. Ways for accurate analysis of high purity materials using the glow discharge mass spectrometry (GD-MS); Wege zur genauen Charakterisierung hochreiner Materialien mit der Glimmentladungs-Massenspektrometrie (GD-MS)

    Energy Technology Data Exchange (ETDEWEB)

    Gusarova, Tamara

    2010-04-14

    The main aim of this work consists in the investigation, development and application of improved possibilities of accurate analysis of high purity materials using the solid sample technique of Glow Discharge Mass Spectrometry (GD-MS), as well as in the sensitivity enhancement of GD Optical Emission Spectrometry (GD-OES) by implicating the hollow cathode effect. The emphasis of the PhD thesis consists in the accurate quantification for GD-MS. As appropriate certified reference materials (CRMs) for calibration are lacking in most cases an accurate quantification especially for trace elements mass fractions at {mu}g kg{sup -1} level can often not be achieved. To overcome this problem and to expand the possibilities of modern GD-MS hereby, synthetic standards were applied for calibration of both high resolution GD-MS instruments ''VG 9000'' and ''Element GD''. The standards were prepared by doping of matrix powder with trace element standard solutions followed by drying and pressing the doped powder to compact pellets. With the quantification approach worked out and described here accurate analysis results with small uncertainties can be achieved for most elements of periodic table in almost every matrix composition. Furthermore direct traceability of the analytical results to the International System of Units (SI) is provided ensuring their higher metrological quality. Numerous additional systematic investigations concerning the preparation of the synthetic standards and their properties were carried out. The results of calibration of GD-MS instruments with synthetic standards for Co (Co-C), Cu, In, Fe and Zn matrices were checked by measuring CRMs. These results were also contrasted with those of other quantification approaches, as usually used in GD-MS routine. The results achieved with synthetic standards had the highest accuracy. The successful participation in the round robin test CCQM-P107 between international

  6. 氯化钡除杂制取高纯氢氧化钡%Preparation of high purity barium hydroxide by impurity - removed barium chloride

    Institute of Scientific and Technical Information of China (English)

    翁贤芬; 毛逢银; 何琳; 李莉

    2009-01-01

    Removal technology of strontium and iron from crude barium chloride raw material were studied.Optimization of process conditions of strontium and iron removal were discussed.When crude barium chloride stiring and dissolving the mixture at 60 ℃ for 40 min,impurities of stromtium and calcuim can be removed and mass fraction of strontium in the obatined solid barium chloride was below 1×10-4.Then add oxydol (H2O2) at proportion of 100 g raw materials per 8 mL H2O2,and add active carbon and small quantity of sodium hydroxide.Finally,iron could be get rid of when pH was controlled below 10.Mass fraction of iron in barium hydroxide product was less than 1×10-5 when using the iron - removed barium chaloride as raw material.Therefore,purified barium chloride by this method can be used to produce purity barium hydroxide.%研究了粗氯化钡原料中锶和铁杂质的脱除工艺,探讨了脱除锶和铁的优化工艺条件.在粗氯化钡原料中加入去离子水,液固质量比为0.25: 1,在60 ℃下搅拌溶解40 min,可除去锶和钙杂质,所得氯化钡固体中锶质量分数低于1×10-4.在氯化钡溶液中加入双氧水,每100 g原料中加入双氧水8 mL,加入活性炭和少量氢氧化钠,控制pH低于10时,可除去铁杂质,用除铁后的氯化钡制取氢氧化钡,产品中铁质量分数低于1×10-5.用除杂后的氯化钡可制得高纯氢氧化钡.

  7. Purity assessment of crystalline zearalenone.

    Science.gov (United States)

    Krska, Rudolf; Welzig, Elvira; Josephs, Ralf D; Kandler, Wolfgang; Pettersson, Hans; MacDonald, Susan; Charlton, Adrian; Brereton, Paul; Hametner, Christian; Berner, Diana; Zöllner, Peter

    2003-01-01

    Commercially available solid zearalenone (ZON) to be used as a certified liquid calibrant (BCR-699) in a project funded by the European Commission within the Standard Measurement and Testing program was characterized and its purity determined. The degree of purity of the ZON was examined by UV spectrophotometer, liquid chromatography (LC) with diode array and fluorescence detection, 1H and 13C-NMR spectrometry, LC-mass spectrometry (LC/MS/MS), ion chromatography (IC), and differential scanning calorimetry (DSC). The diagrams obtained from DSC analysis and the UV spectrum showed no detectable impurities. Likewise, no impurities were observed by LC analysis with both diode array and fluorescence detection. IC determination revealed negligible contamination of ZON with chloride of 0.020 +/- 0.005% and nitrate of 0.016 +/- 0.006%. Zearalanone (ZAN) was identified as one of 2 minor (0.2%) impurities by LC/MS/MS. The 1H-NMR measurements revealed an additional peak, which has not been previously reported in the literature. It could be identified as part of the ZON spectrum as the signal arising from the phenolic proton attached to C4'. The manufacturer states an additional contamination with 0.2% methylene chloride, which could be confirmed to an extent of 0.1% by 1H-NMR. Minor impurities, whose structures remain unknown, were discovered at 3.5 and project.

  8. Iodine Absorption Cells Purity Testing

    Directory of Open Access Journals (Sweden)

    Jan Hrabina

    2017-01-01

    Full Text Available This article deals with the evaluation of the chemical purity of iodine-filled absorption cells and the optical frequency references used for the frequency locking of laser standards. We summarize the recent trends and progress in absorption cell technology and we focus on methods for iodine cell purity testing. We compare two independent experimental systems based on the laser-induced fluorescence method, showing an improvement of measurement uncertainty by introducing a compensation system reducing unwanted influences. We show the advantages of this technique, which is relatively simple and does not require extensive hardware equipment. As an alternative to the traditionally used methods we propose an approach of hyperfine transitions’ spectral linewidth measurement. The key characteristic of this method is demonstrated on a set of testing iodine cells. The relationship between laser-induced fluorescence and transition linewidth methods will be presented as well as a summary of the advantages and disadvantages of the proposed technique (in comparison with traditional measurement approaches.

  9. Blue-emitting K2Al2B2O7:Eu(2+) phosphor with high thermal stability and high color purity for near-UV-pumped white light-emitting diodes.

    Science.gov (United States)

    Xiao, Wenge; Zhang, Xia; Hao, Zhendong; Pan, Guo-Hui; Luo, Yongshi; Zhang, Ligong; Zhang, Jiahua

    2015-04-06

    Novel blue-emitting K2Al2B2O7:Eu(2+) (KAB:Eu(2+)) phosphor was synthesized by solid state reaction. The crystal structural and photoluminescence (PL) properties of KAB:Eu(2+) phosphor, as well as its thermal properties of the photoluminescence, were investigated. The KAB:Eu(2+) phosphor exhibits broad excitation spectra ranging from 230 to 420 nm, and an intense asymmetric blue emission band centered at 450 nm under λex = 325 nm. Two different Eu(2+) emission centers in KAB:Eu(2+) phosphor were confirmed via their fluorescence decay lifetimes. The optimal concentration of Eu(2+) ions in K2-xEuxAl2B2O7 was determined to be x = 0.04 (2 mol %), and the corresponding concentration quenching mechanism was verified to be the electric dipole-dipole interactions. The PL intensity of the nonoptimized KAB:0.04Eu(2+) phosphor was measured to be ∼58% that of the commercial blue-emitting BaMgAl10O17:Eu(2+) phosphor, and this phosphor has high color purity with the CIE coordinate (0.147, 0.051). When heated up to 150 °C, the KAB:0.04Eu(2+) phosphor still has 82% of the initial PL intensity at room temperature, indicating its high thermal stability. These results suggest that the KAB:Eu(2+) is a promising candidate as a blue-emitting n-UV convertible phosphor for application in white light emitting diodes.

  10. Study of the recrystallization mechanisms of ultra-high purity iron doped with carbon, manganese and phosphorus; Etude des mecanismes de recristallisation dans le fer de ultra-haute purete dope en carbone, manganese et phosphore

    Energy Technology Data Exchange (ETDEWEB)

    Lesne, L.

    2000-07-04

    High purity steels have the potential to improve deep drawing properties for automotive applications. Understanding the influence of the chemical composition on the recrystallization mechanisms and on texture development should help to improve their properties. We have studied the influence of 10 ppm of carbon, 1000 ppm of manganese and 120 ppm of phosphorus on the recrystallization mechanisms of ultra-high purity iron (UHP iron > 99.997%). For this purpose we used 4 materials: one undoped (UHP), one doped with C, one doped with C, Mn and one doped With C, Mn, P. In order to restrict grain coarsening in the hot strips, hot rolling was performed in the ferritic region, in one pass of 80% thickness reduction. The hot bands were then fully recrystallized but exhibited non-isotropic textures, with in particular an intense Goss [110]<001> component for the doped materials. The hot-bands were subsequently cold rolled down to a thickness of 0.8 mm corresponding to a thickness reduction of 80%, and then continuously annealed at 10 deg. C/s. The recrystallization kinetics are delayed with the addition of doping elements. In particular, the incubation time for nucleation is shifted towards higher temperatures while the recrystallization velocity increases. The textures of the fully recrystallized materials exhibit a strong Goss component prejudicial for deep drawing properties. We have established that this component can only appear if coarse grains and carbon in solid solution were simultaneously present in the material before deformation. Characterisation of the cold deformed state enabled us to evaluate the energy stored during deformation as a function of the material composition and the grain orientation: - the overall stored energy increases with the doping elements content. - the stored energy in the {gamma} fibre grains is greater than in the {alpha} fibre grains: 30 J/mol for the {gamma} fibre instead of 5 J/mol for the {alpha} fibre, in the undoped UHP iron. In the

  11. Thermal expansion of gadolinium in the vicinity of the Curie point. [270 to 320/sup 0/K, Curie point exponents

    Energy Technology Data Exchange (ETDEWEB)

    Dolejsi, D.A.

    1977-02-01

    The c- and a-axis linear thermal expansivities of high purity single crystals of gadolinium were measured in the temperature range 270/sup 0/K to 320/sup 0/K. Length changes were translated to capacitance changes with a modified normal geometry 3-terminal capacitance dilatometer. An ac 3-terminal capacitance bridge was employed to measure nominal 10 pF capacitances to a precision of 10/sup -7/ pF, which corresponds to a relative length change sensitivity of 10/sup -10/. A 25 ohm platinum resistance thermometer was used to detect the dilatometer temperature to a precision of 10 ..mu..K with an ac resistance bridge. The c-axis expansivity was negative and had a large (approximately equal to 10/sup -4/ K/sup -1/) peak at 293.435/sup 0/K, while the a-axis expansivity was positive and had a smaller (approximately equal to 10/sup -5/ K/sup -1/) peak at 293.363/sup 0/K. The values of the Curie temperatures (T/sub c/'s) and critical point exponents for the c- and a-axis crystals were obtained from fitting power law equations to the expansivities.

  12. Realization of the low background neutrino detector Double Chooz. From the development of a high-purity liquid and gas handling concept to first neutrino data

    Energy Technology Data Exchange (ETDEWEB)

    Pfahler, Patrick

    2012-12-17

    Neutrino physics is one of the most vivid fields in particle physics. Within this field, neutrino oscillations are of special interest as they allow to determine driving oscillation parameters, which are collected as mixing angles in the leptonic mixing matrix. The exact knowledge of these parameters is the main key for the investigation of new physics beyond the currently known Standard Model of particle physics. The Double Chooz experiment is one of three reactor disappearance experiments currently taking data, which recently succeeded to discover a non-zero value for the last neutrino mixing angle {Theta}{sub 13}. As successor of the CHOOZ experiment, Double Chooz will use two detectors with improved design, each of them now composed of four concentrically nested detector vessels each filled with different detector liquid. The integrity of this multi-layered structure and the quality of the used detector liquids are essential for the success of the experiment. Within this frame, the here presented work describes the production of two detector liquids, the filling and handling of the Double Chooz far detector and the installation of all necessary hardware components therefore. In order to meet the strict requirements existing for the detector liquids, all components were individually selected in an extensive material selection process at TUM, which compared samples from different companies for their key properties: density, transparency, light yield and radio purity. Based on these measurements, the composition of muon veto scintillator and buffer liquid were determined. For the production of the detector liquids, a simple surface building close to the far detector site was upgraded into a large-scale storage and mixing facility, which allowed to separately, mix, handle and store 90 m{sup 3} of muon veto scintillator and 110 m{sup 3} of buffer liquid. For the muon veto scintillator, a master-solution composed of 4800 l LAB, 180 kg PPO and 1.8 kg of bis/MSB was

  13. Preparation of High Purity Manganese Carbonate from the Reduction of Pyrolusite Using Cane Juice as the Reductant%甘蔗汁还原软锰矿制备高纯碳酸锰工艺研究

    Institute of Scientific and Technical Information of China (English)

    蔡振勇; 易清风; 宋伟

    2011-01-01

    采用甘蔗汁作为还原剂,在稀硫酸介质中湿法还原软锰矿制备高纯碳酸锰.当甘蔗汁与软锰矿质量比为1.15时,锰的浸出率在95%以上.用活性炭对硫酸锰滤液进行吸附处理,通过单因素实验确定最佳脱色工艺参数,结果表明:当活性炭与甘蔗汁质量比为0.1,溶液pH值为2,反应时间3h时,硫酸锰粗滤液的脱色率在94%以上;然后加入硫化钡除去溶液的重金属离子,过滤,向滤液中加入二氟化锰使溶液中的钙、镁等离子沉淀除去得高纯硫酸锰溶液,将碳酸氢铵加入硫酸锰溶液中制备出高纯碳酸锰.经检测产品纯度在95%以上.%In this paper, manganese carbonate was prepared by the reduction of pyrolusite with cane juice as a reductant in dilute sulfuric acid solution. When the mass ratio of cane juice to pyrolusite is 1.15, the leaching rate of manganese can reach more than 95%. Manganese sulfate solution was treated by using activated carbon in order to remove the impurities. Optimal parameters affecting the decolorization efficiency were determined by the single factor method. The results show that the decolorzation rate can reach more than 94% under the condition of activated carbon to cane juice quality mass ratio of 0.1 ,pH 2,and reaction time of 3 h. Heavy metal ions were removed by adding barium sulfide to the solution. After being filtrated,manganese difluoride was added to the filtrate to precipitate Ca2+ ,Mg2+ and other impurities, and high purity manganese sulfate solution was then obtained. High purity manganese carbonate was prepared by adding ammonium bicarbonate to the pure manganese sulfate solution. Manganese carbonate purity can reach more than 95% .

  14. Technology for sodium purity control

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Ji Young; Kim, B. H.; Kim, T. J. [Korea Atomic Energy Research Institute, Taejon (Korea)

    1999-10-01

    When sodium is used as heat transfer fluid, the plugging in coolant flow, the corrosion of structure material and the transfer of radioactive material caused by the impurities in sodium are worth considerable. Accordingly, these impurities must be monitored and controlled continuously by sodium purification devices in the heat transfer system which sodium is used as coolant. Sodium purification loop was constructed for the purpose of accumulating the technology for purity control of the coolant, developing and verifying further efficient instruments for sodium purification. The plugging meter and the cold trap is used as the implement for measuring and controlling the oxygen and the hydrogen, the main impurities in sodium coolant. They are capable of excellent performance as the implements which could detect and monitor the impurities to the concentration limit required for nuclear reactor. Sodium purification loop could be used variably according to the experimental purpose. 18 refs., 34 figs., 8 tabs. (Author)

  15. Simulation for photon detection in spectrometric system of high purity (HPGe) using MCNPX code; Simulacao de deteccao de fotons em sistema espectrometrico de alta pureza (HPGe) usando o codigo MCNPX

    Energy Technology Data Exchange (ETDEWEB)

    Correa, Guilherme Jorge de Souza

    2013-07-01

    The Brazilian National Commission of Nuclear Energy defines parameters for classification and management of radioactive waste in accordance with the activity of materials. The efficiency of a detection system is crucial to determine the real activity of a radioactive source. When it's possible, the system's calibration should be performed using a standard source. Unfortunately, there are only a few cases that it can be done this way, considering the difficulty of obtaining appropriate standard sources for each type of measurement. So, computer simulations can be performed to assist in calculating of the efficiency of the system and, consequently, also auxiliary the classification of radioactive waste. This study aims to model a high purity germanium (HPGe) detector with MCNPX code, approaching the spectral values computationally obtained of the values experimentally obtained for the photopeak of {sup 137}Cs. The approach will be made through changes in outer dead layer of the germanium crystal modeled. (author)

  16. Measurements of gamma (γ)-emitting radionuclides with a high-purity germanium detector: the methods and reliability of our environmental assessments on the Fukushima 1 Nuclear Power Plant accident.

    Science.gov (United States)

    Mimura, Tetsuro; Mimura, Mari; Komiyama, Chiyo; Miyamoto, Masaaki; Kitamura, Akira

    2014-01-01

    The severe accident of Fukushima 1 Nuclear Power Plant due to the Tohoku Region Pacific Coast Earthquake in 11 March 2011 caused wide contamination and pollution by radionuclides in Fukushima and surrounding prefectures. In the current JPR symposium, a group of plant scientists attempted to examine the impact of the radioactive contamination on wild and cultivated plants. Measurements of gamma (γ) radiation from radionuclides in "Fukushima samples", which we called and collected from natural and agricultural areas in Fukushima prefecture were mostly done with a high-purity Ge detector in the Graduate School of Maritime Sciences, Kobe University. In this technical note, we describe the methods of sample preparation and measurements of radioactivity of the samples and discuss the reliability of our data in regards to the International Atomic Energy Agency (IAEA) Interlaboratory comparisons and proficiency test (IAEA proficiency test).

  17. Removal and separation of impurity ions in preparation of high-purity inorganic salts%高纯无机盐制备中杂质离子的去除与分离

    Institute of Scientific and Technical Information of China (English)

    石磊

    2012-01-01

    介绍了在制备高纯无机盐过程中,有害杂质离子——重有色金属离子(Cu、Mg、Zn、Pd、Cd等)、铁离子、砷化物的去除与分离方法:氧化-还原法、难溶金属氢氧化物沉淀法、硫化物沉淀法.%Introduced in the preparation of high purity inorganic salt process, harmful impurity ion-heavy non-ferrous metal ion (Cu,Mg,Zn,Pd,CDS,etc. ) ,iron ion,arsenide in removing and separation methods : oxidation-reduction method and difficult to thick metal hydroxide precipitation, sulfide precipitation.

  18. 超净高纯电子化学试剂——异丙醇制备方法%Preparation method of ultra-dean and high-purity reagents——isopropanol

    Institute of Scientific and Technical Information of China (English)

    梁凯

    2011-01-01

    Hie ultra-clean and high-purity reagent-isopropanol was prepared with 98% industrial isopropanol by the process of metallic ion complexation, dehydration, microfiltration, multilevel rectification and filtration by sodium filter membrane. The isopropanol meets the requirements of clean and corrosion of semiconductor chip.%本文介绍了用含量98%的工业级异丙醇经过金属离子络合剂处理、脱水处理、微滤膜过滤、多级精馏、钠滤膜过滤制备超净高纯电子化学试剂-异丙醇的制备方法.该方法制备的超净高纯异丙醇符合半导体技术的芯片及硅园片的清洗和刻蚀的要求.

  19. On line chemical analyzers for high purity steam and water, applied to steam power plants; Analizadores quimicos en linea para agua y vapor de alta pureza, aplicados a centrales termoelectricas

    Energy Technology Data Exchange (ETDEWEB)

    Diaz Perez, Ruth [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

    1989-12-31

    This article presents a general overview of the advances in the subject of on line analyzers of chemical parameters for high purity water and steam and specifies which ones are commercially available. Also are mentioned besides, the criteria nowadays applied for the selection of the sites for sample grabbing and the analysis that is necessary to perform in each point, depending on the power plant type and the treatment administered (phosphates-Ph coordinated or AVT treatment). [Espanol] El articulo presenta un panorama general de los avances que en materia de analizadores de parametros quimicos en linea para agua y vapor de alta pureza, y especifica cuales estan disponibles en forma comercial. Se citan, ademas los criterios que se aplican actualmente para seleccionar los puntos de toma de muestra y los analisis que es necesario efectuar en cada punto, dependiendo del tipo de central y del tratamiento que se le administre (fosfatos-pH coordinado o tratamiento AVT).

  20. Compensated gadolinium-loaded plastic scintillators for thermal neutron detection (and counting)

    Energy Technology Data Exchange (ETDEWEB)

    Dumazert, Jonathan; Coulon, Romain; Bertrand, Guillaume H. V.; Hamel, Matthieu; Sguerra, Fabien; Dehe-Pittance, Chrystele; Normand, Stephane [CEA, LIST, Laboratoire Capteurs Architectures Electroniques, 99 Gif-sur-Yvette, (France); Mechin, Laurence [CNRS, UCBN, Groupe de Recherche en Informatique, Image, Automatique et Instrumentation de Caen, 4050 Caen, (France)

    2015-07-01

    Plastic scintillator loading with gadolinium-rich organometallic complexes shows a high potential for the deployment of efficient and cost-effective neutron detectors. Due to the low-energy photon and electron signature of thermal neutron capture by gadolinium-155 and gadolinium-157, alternative treatment to Pulse Shape Discrimination has to be proposed in order to display a trustable count rate. This paper discloses the principle of a compensation method applied to a two-scintillator system: a detection scintillator interacts with photon radiation and is loaded with gadolinium organometallic compound to become a thermal neutron absorber, while a non-gadolinium loaded compensation scintillator solely interacts with the photon part of the incident radiation. Posterior to the nonlinear smoothing of the counting signals, a hypothesis test determines whether the resulting count rate after photon response compensation falls into statistical fluctuations or provides a robust image of a neutron activity. A laboratory prototype is tested under both photon and neutron irradiations, allowing us to investigate the performance of the overall compensation system in terms of neutron detection, especially with regards to a commercial helium-3 counter. The study reveals satisfactory results in terms of sensitivity and orientates future investigation toward promising axes. (authors)

  1. A toxicological study of gadolinium nitrate

    Energy Technology Data Exchange (ETDEWEB)

    London, J.E.

    1988-05-01

    The sensitization study in the guinea pig did not show gadolinium nitrate to have potential sensitizing properties. Skin application studies in the rabbit demonstrated that it was cutaneously a severe irritant. This material was considered an irritant in the rabbit eye application studies. 3 refs., 1 tab.

  2. Gadolinium-based nanoparticles for theranostic MRI-radiosensitization.

    Science.gov (United States)

    Lux, François; Sancey, Lucie; Bianchi, Andrea; Crémillieux, Yannick; Roux, Stéphane; Tillement, Olivier

    2015-01-01

    A rapid development of gadolinium-based nanoparticles is observed due to their attractive properties as MRI-positive contrast agents. Indeed, they display high relaxivity, adapted biodistribution and passive uptake in the tumor thanks to enhanced permeability and retention effect. In addition to these imaging properties, it has been recently shown that they can act as effective radiosensitizers under different types of irradiation (radiotherapy, neutron therapy or hadron therapy). These new therapeutic modalities pave the way to therapy guided by imaging and to personalized medicine.

  3. [Causal relationship between the use of gadolinium based contrast media and nephrogenic systemic fibrosis].

    Science.gov (United States)

    Varela, Cristian U; Prieto-Rayo, Juan Carlos

    2014-12-01

    Nephrogenic systemic fibrosis (NSF) is a severe iatrogenic disease that affect patients with impaired renal function exposed to gadolinium-based contrast agents. Clinically, symptoms develop within days or weeks after the exposure and mimic a scleromyxedema. The causal relationship between use of gadolinium-based contrast agents and NSF led to develop clinical guidelines aiming to limit the use of this contrast medium in high risk patients. These guidelines decreased the incidence of NSF in the last years. Unfortunately there is no specific treatment for NSF yet. Thus, strict adherence to current guidelines is key to prevent new cases. Renal dysfunction is increasingly common in our population. Therefore, practicing physicians should be aware of this potential complication of the use of gadolinium based contrast media.

  4. Effective lattice stabilization of gadolinium aluminate garnet (GdAG via Lu3+ doping and development of highly efficient (Gd,LuAG:Eu3+ red phosphors

    Directory of Open Access Journals (Sweden)

    Jinkai Li, Ji-Guang Li, Zhongjie Zhang, Xiaoli Wu, Shaohong Liu, Xiaodong Li, Xudong Sun and Yoshio Sakka

    2012-01-01

    Full Text Available The metastable garnet lattice of Gd3Al5O12 is stabilized by doping with smaller Lu3+, which then allows an effective incorporation of larger Eu3+ activators. The [(Gd1−xLux1−yEuy]3Al5O12 (x = 0.1–0.5, y = 0.01–0.09 garnet solid solutions, calcined from their precursors synthesized via carbonate coprecipitation, exhibit strong luminescence at 591 nm (the 5D0 → 7F1 magnetic dipole transition of Eu3+ upon UV excitation into the charge transfer band (CTB at ~239 nm, with CIE chromaticity coordinates of x = 0.620 and y = 0.380 (orange-red. The quenching concentration of Eu3+ was estimated at ~5 at.% (y = 0.05, and the quenching was attributed to exchange interactions. Partial replacement of Gd3+ with Lu3+ up to 50 at.% (x = 0.5 while keeping Eu3+ at the optimal content of 5 at.% does not significantly alter the peak positions of the CTB and 5D0 → 7F1 emission bands but slightly weakens both bands owing to the higher electronegativity of Lu3+. The effects of processing temperature (1000–1500 °C and Lu/Eu contents on the intensity, quantum efficiency, lifetime and asymmetry factor of luminescence were thoroughly investigated. The [(Gd0.7Lu0.30.95Eu0.05]3Al5O12 phosphor processed at 1500 °C exhibits a high internal quantum efficiency of ~83.2% under 239 nm excitation, which, in combination with the high theoretical density, favors its use as a new type of photoluminescent and scintillation material.

  5. Tracing gadolinium-based contrast agents from surface water to drinking water by means of speciation analysis.

    Science.gov (United States)

    Birka, Marvin; Wehe, Christoph A; Hachmöller, Oliver; Sperling, Michael; Karst, Uwe

    2016-04-01

    In recent decades, a significant amount of anthropogenic gadolinium has been released into the environment as a result of the broad application of contrast agents for magnetic resonance imaging (MRI). Since this anthropogenic gadolinium anomaly has also been detected in drinking water, it has become necessary to investigate the possible effect of drinking water purification on these highly polar microcontaminats. Therefore, a novel highly sensitive method for speciation analysis of gadolinium is presented. For that purpose, the hyphenation of hydrophilic interaction liquid chromatography (HILIC) and inductively coupled plasma-mass spectrometry (ICP-MS) was employed. In order to enhance the detection power, sample introduction was carried out by ultrasonic nebulization. In combination with a novel HILIC method using a diol-based stationary phase, it was possible to achieve superior limits of detection for frequently applied gadolinium-based contrast agents below 20pmol/L. With this method, the contrast agents Gd-DTPA, Gd-DOTA and Gd-BT-DO3A were determined in concentrations up to 159pmol/L in samples from several waterworks in a densely populated region of Germany alongside the river Ruhr as well as from a waterworks near a catchment lake. Thereby, the direct impact of anthropogenic gadolinium species being present in the surface water on the amount of anthropogenic gadolinium in drinking water was shown. There was no evidence for the degradation of contrast agents, the release of Gd(3+) or the presence of further Gd species.

  6. Observation of Neutrons with a Gadolinium Doped Water Cerenkov Detector

    CERN Document Server

    Dazeley, S; Bowden, N S; Svoboda, R

    2008-01-01

    Spontaneous and induced fission in Special Nuclear Material (SNM) such as 235U and 239Pu results in the emission of neutrons and high energy gamma-rays. The multiplicities of and time correlations between these particles are both powerful indicators of the presence of fissile material. Detectors sensitive to these signatures are consequently useful for nuclear material monitoring, search, and characterization. In this article, we demonstrate sensitivity to both high energy gamma-rays and neutrons with a water Cerenkov based detector. Electrons in the detector medium, scattered by gamma-ray interactions, are detected by their Cerenkov light emission. Sensitivity to neutrons is enhanced by the addition of a gadolinium compound to the water in low concentrations. Cerenkov light is similarly produced by an 8 MeV gamma-ray cascade following neutron capture on the gadolinium. The large solid angle coverage and high intrinsic efficiency of this detection approach can provide robust and low cost neutron and gamma-ray...

  7. Mitochondrial dysfunction induced by different concentrations of gadolinium ion.

    Science.gov (United States)

    Zhao, Jie; Zhou, Zhi-Qiang; Jin, Jian-Cheng; Yuan, Lian; He, Huan; Jiang, Feng-Lei; Yang, Xiao-Gang; Dai, Jie; Liu, Yi

    2014-04-01

    Gadolinium-based compounds are the most widely used paramagnetic contrast agents in magnetic resonance imaging on the world. But the tricationic gadolinium ion (Gd(3+)) could induce cell apoptosis probably because of its effects on mitochondria. Until now, the mechanism about how Gd(3+) interacts with mitochondria is not well elucidated. In this work, mitochondrial swelling, collapsed transmembrane potential and decreased membrane fluidity were observed to be important factors for mitochondrial permeability transition pore (mtPTP) opening induced by Gd(3+). The protection effect of CsA (Cyclosporin A) could confirm high concentration of Gd(3+) (500 μM) would trigger mtPTP opening. Moreover, mitochondrial outer membrane breakdown and volume expansion observed clearly by transmission electron microscopy and the release of Cyt c (Cytochrome c) could explain the mtPTP opening from another aspect. In addition, MBM(+) (monobromobimane(+)) and DTT (dithiothreitol) could protect thiol (-SH) groups from oxidation so that the toxicity of Gd(3+) might be resulted from the chelation of -SH of membrane proteins by free Gd(3+). Gd(3+) could inhibit the initiation of mitochondrial membrane lipid peroxidation, so it might interact with anionic lipids too. These findings will highly contribute to the safe applications of Gd-based agents.

  8. Strengthening Purity: Moral Purity as a Mediator of Direct and Extended Cross-Group Friendships on Sexual Prejudice.

    Science.gov (United States)

    Vezzali, Loris; Brambilla, Marco; Giovannini, Dino; Paolo Colucci, Francesco

    2017-01-01

    The present research investigated whether enhanced perceptions of moral purity drive the effects of intergroup cross-group friendships on the intentions to interact with homosexuals. High-school students (N = 639) reported their direct and extended cross-group friendships with homosexuals as well as their beliefs regarding the moral character of the sexual minority. Participants further reported their desire to interact with homosexuals in the future. Results showed that both face-to-face encounters and extended contact with homosexuals increased their perceived moral purity, which in turn fostered more positive behavioral intentions. Results further revealed the specific role of moral purity in this sense, as differential perceptions along other moral domains (autonomy and community) had no mediation effects on behavioral tendencies toward homosexuals. The importance of these findings for improving intergroup relations is discussed, together with the importance of integrating research on intergroup contact and morality.

  9. Simulation analysis of energy saving distillation processes for high-purity SiHCl3%高纯三氯氢硅精馏节能工艺的模拟分析

    Institute of Scientific and Technical Information of China (English)

    李闻笛; 廉景燕; 丛山; 李洪

    2012-01-01

    Due to the property of highly energy consuming in the purification process of high-purity SiHCl3 in polycrystalline silicon production, this study focuses on separately applying two energy saving processes, heat pump and thermally coupled distillation with different pressure, to the purifying distillation process of high-purity SiHCl3. Aspen Plus is used to simulate the two energy saving processes for analysis and comparison. The energy consumptions of both processes are calculated to achieve the goal of energy saving and optimization. The simulation results show that an obvious energy saving effect for the traditional distillation process in SiHCl3 production is achieved by applying either heat pump or thermally coupled distillation with different pressure. The vapor recompression and liquid flash heat pump processes allow a save on energy of 66. 1% and 62. 8% respectively. And the process of thermally coupled distillation with different pressure can reach 50. 1 % of energy saving.%针对多晶硅生产中高纯三氯氢硅精馏提纯过程能耗较高的特点,分别将热泵和差压热耦合精馏节能工艺应用到高纯三氯氢硅精馏提纯过程中,并使用Aspen Plus软件对这2种节能工艺进行模拟分析比较,计算得到各工艺流程的能耗,实现了过程的节能和优化.模拟结果表明,热泵和差压热耦合精馏节能工艺对三氯氢硅传统二塔精馏过程均起到了显著的节能效果,其中塔顶蒸汽压缩型、塔釜液闪蒸型热泵精馏过程分别节能66.1%、62.8%,差压热耦合精馏过程节能50.1%.

  10. A summary of volatile impurity measurements and gas generation studies on MISSTD-1, a high-purity plutonium oxide produced by low-temperature calcination of plutonium oxalate

    Energy Technology Data Exchange (ETDEWEB)

    Berg, John M. [Los Alamos National Laboratory; Narlesky, Joshua E. [Los Alamos National Laboratory; Veirs, Douglas K. [Los Alamos National Laboratory

    2012-06-08

    Plutonium dioxide of high specific surface area was subjected to long-term tests of gas generation in sealed containers. The material preparation and the storage conditions were outside the bounds of acceptable parameters defined by DOE-STD-3013-2012 in that the material was stabilized to a lower temperature than required and had higher moisture content than allowed. The data provide useful information for better defining the bounding conditions for safe storage. Net increases in internal pressure and transient increases in H{sub 2} and O{sub 2} were observed, but were well within the bounds of gas compositions previously shown to not threaten integrity of 3013 containers.

  11. Production of high optical purity l-lactic acid from waste activated sludge by supplementing carbohydrate: effect of temperature and pretreatment time.

    Science.gov (United States)

    Jian, Qiwei; Li, Xiang; Chen, Yinguang; Liu, Yanan; Pan, Yin

    2016-10-01

    It has been widely accepted that the most environmentally beneficial way to treat waste activated sludge (WAS), the byproduct of municipal wastewater treatment plant, is to recover the valuable organic acid. However, the bio-conversion of lactic acid, one of the high added-value chemical, is seldom reported from WAS fermentation. In this paper, l-lactic acid was observed dominant in the WAS fermentation liquid with carbohydrate addition at ambient temperature. Furthermore, the effect of temperature on l-lactic acid and d-lactic acid production was fully discussed: two isomers were rapidly produced and consumed up in one day at mesophilic condition; and almost optically pure l-lactic acid was generated at thermophilic condition, yet time-consuming with yield of l-lactic acid enhancing by 52.9% compared to that at ambient temperature. The study mechanism showed that mesophilic condition was optimal for both production and consumption of l-lactic acid and d-lactic acid, while consumption of l-lactic acid and production of d-lactic acid were severely inhibited at thermophilic condition. Therefore, by maintaining thermophilic for 4 h in advance and subsequently fermenting mesophilic for 34 h, the concentration of l-lactic acid with optical activity of 98.3% was improved to 16.6 ± 0.5 g COD/L at a high specific efficiency of 0.6097/d.

  12. A Rapid One-Pot Synthesis of Novel High-Purity Methacrylic Phosphonic Acid (PA-Based Polyhedral Oligomeric Silsesquioxane (POSS Frameworks via Thiol-Ene Click Reaction

    Directory of Open Access Journals (Sweden)

    K. Karuppasamy

    2017-05-01

    Full Text Available Herein, we demonstrate a facile methodology to synthesis a novel methacrylic phosphonic acid (PA-functionalized polyhedral oligomeric silsesquioxanes (POSSs via thiol-ene click reaction using octamercapto thiol-POSS and ethylene glycol methacrylate phosphate (EGMP monomer. The presence of phosphonic acid moieties and POSS-cage structure in POSS-S-PA was confirmed by Fourier transform infrared (FT-IR and nuclear magnetic resonance (1H, 29Si and 31P-NMR analyses. Matrix-assisted laser desorption ionization time-of-flight (MALDI-TOF mass spectrum of POSS-S-PA acquired in a dithranol matrix, which has specifically designed for intractable polymeric materials. The observed characterization results signposted that novel organo-inorganic hybrid POSS-S-PA would be an efficacious material for fuel cells as a proton exchange membrane and high-temperature applications due to its thermal stability of 380 °C.

  13. Gadolinium and nephrogenic systemic fibrosis: an update.

    Science.gov (United States)

    Weller, Alex; Barber, Joy L; Olsen, Oystein E

    2014-10-01

    Nephrogenic systemic fibrosis (NSF) is a multisystem disease seen exclusively in patients with renal impairment. It can be severely debilitating and sometimes fatal. There is a strong association with gadolinium-based contrast agents used in magnetic resonance imaging (MRI). Risk factors include renal impairment and proinflammatory conditions, e.g. major surgery and vascular events. Although there is no single effective treatment for NSF, the most successful outcomes are seen following restoration of renal function, either following recovery from acute kidney injury or following renal transplantation. There have been ten biopsy-proved pediatric cases of NSF, with no convincing evidence that children have a significantly altered risk compared with the adult population. After implementation of guidelines restricting the use of gadolinium-based contrast agents in at-risk patients, there has been a sharp reduction in new cases and no new reports in children. Continued vigilance is recommended: screening for renal impairment, use of more stable gadolinium chelates, consideration of non-contrast-enhanced MRI or alternative imaging modalities where appropriate.

  14. Effect of gadolinium nitrate concentration on molecular product yield during gamma irradiation and on corrosion of stainless steel

    Science.gov (United States)

    Mal, D.; Puspalata, R.; Rangarajan, S.; Velmurugan, S.

    2017-09-01

    Effect of high concentrations of soluble neutron poison gadolinium nitrate, Gd(NO3)3, in the moderator system of a proposed advanced Indian nuclear reactor, was evaluated from the safety point of view. The radiolytic yields of H2 and H2O2 was expected to be high as moderator water system pH would be lowered and conductivity also would be high by the addition of higher concentration Gd(NO3)3 solutions during various shutdown states. Experiments were carried out to estimate this increase in radiolytic yield of molecular products with the addition of Gd(NO3)3 in the concentration range of 15-400 mg kg-1. Both the H2O2 and H2 yields were found to increase with absorbed dose and also with increasing Gd3+ concentration up to 100 mg kg-1 but the increase were marginal in 100-400 mg kg-1 range. For a given concentration of Gd(NO3)3 solution, radiolysis in high purity D2O showed a lower D2 formation than H2 in light water. In a simulated moderator temperature of 65 °C, a higher yield of H2 was observed. The headspace provided above the liquid phase in irradiation zone had shown to have a substantial effect on the generation of H2. With decreasing headspace, H2 generation increased and went through a maximum. Considering the expected long operational life ( 100 years) for the proposed reactor, the corrosion rate of the structural materials (stainless steel 304 LN) in contact with this high concentration Gd(NO3)3 solution was also estimated at 65 °C which showed a negligible effect.

  15. Preparation of High-purity Reactive Black for Digital Printing with MF/NF Separation Technology%微滤/纳滤分离工艺制备数码喷墨印花高纯活性黑

    Institute of Scientific and Technical Information of China (English)

    张浩勤; 王慧; 秦国胜; 黄满满; 张亚涛

    2013-01-01

    In this paper,the high purity liquid reactive black was prepared by using the membrane separation technology,including the microfiltration(MF) membrane for removing particulate,the Charged-mosiac membrane (CMM) for desalination in the constant-volume filtration and the nanofiltration(NF) membrane for dehydration.The solid reactive black with high purity was prepared by spray drying.The experimental results show that with the 61.5 g · L-1 raw material liquid,under the pressure of 1.0 MPa,the salts were removed after 8 hours desalination.The purity of dye could meet the requirement and the loss rate of the dye was 0.62%.The average permeation flux of the charged-mosiac membrane was 18.5 L · m-2 · h-1 during the desalination process,which illustrated that the fouling of membrane was not so serious.Under the pressure of 1.4-1.8 MPa,the reactive black concentration can achieve 250 g · L-1 by dehydration.The solid dye was prepared by the spray drying.It was analysed that the inorganic salt in the product was lower than the imported product used by the enterprise.To sum up,the product prepared in the experiment has a good application prospect.%实验以国产活性黑粗染料为原料,采用微滤膜除杂、荷电镶嵌膜恒容脱盐和纳滤膜脱水浓缩工艺制备高纯度、高浓度液体活性染料;并通过喷雾干燥制备了高纯固体活性黑.实验结果表明:针对染料含量为61.5 g/L的原料液,在操作压力1.0 MPa条件下,脱盐8h染料纯度达到要求,染料损失率为0.62%;脱盐过程中荷电镶嵌膜的平均透过通量约为18.5 L·m-2· h-1.在1.4~1.8 MPa下,可将高纯料液脱水浓缩,使活性黑浓度达到250 g/L.实验采用喷雾干燥法制备固体染料,经分析该产品的无机盐含量低于企业目前所用的进口产品,具有良好的应用前景.

  16. Cause-specific mortality and cancer morbidity in 390 male workers exposed to high purity talc, a six-decade follow-up.

    Science.gov (United States)

    Wergeland, Ebba; Gjertsen, Finn; Vos, Linda; Grimsrud, Tom K

    2017-09-01

    This study updates information on mortality and cancer morbidity in a cohort of Norwegian talc workers. Follow-up was extended with 24 years, covering 1953-2011. Comparisons were made with the general population and between subgroups within the cohort. Standardized mortality ratio for non-malignant respiratory disease (NMRD) was 0.38 (95%CI: 0.18, 0.69) and for diseases of the circulatory system (CVD) 0.98 (95%CI: 0.82, 1.16). A non-significantly increased NMRD risk was observed at high dust exposures. There were no deaths from pneumoconiosis. With the clear limitations of a small cohort, our results do hint at an effect of talc dust on mortality from NMRD other than pneumoconiosis, covered by a strong and persisting healthy worker effect. Also, an effect on CVD mortality, masked by a healthy worker selection into the cohort cannot be ruled out. Excess mortality from pneumoconiosis seen in other studies, may reflect exposure to quartz and, possibly, bias due to comparability problems. © 2017 Wiley Periodicals, Inc.

  17. Reactor antineutrino oscillations and gadolinium loaded Super-Kamiokande detector

    Energy Technology Data Exchange (ETDEWEB)

    Choubey, Sandhya; Petcov, S.T

    2004-08-05

    We explore the potential of measuring the solar neutrino oscillation parameters in the proposed gadolinium loaded Super-Kamiokande (SK-Gd) detector. Gadolinium dissolved in water can detect neutrons much more efficiently than pure water. This imparts the detector the ability to observe electron type antineutrinos, transforming Super-Kamiokande into a huge reactor antineutrino detector with an event rate approximately 43 times higher than that observed in KamLAND. We simulate the reactor antineutrino data expected in this high statistics detector. We use these prospective data to study the precision with which the solar neutrino oscillation parameters, {delta}m{sup 2}{sub o} and sin{sup 2}{theta}{sub o}, can be determined (i) with the SK-Gd detector, and (ii) by combining the SK-Gd data with the global data on solar neutrino oscillations. For comparison and completeness the allowed regions of {delta}m{sup 2}{sub o} and sin{sup 2}{theta}{sub o}, expected to be obtained from the data of the solar neutrino and KamLAND experiments, are also presented. We find that the SK-Gd experiment could provide one of the most precise (if not the most precise) determination of the solar neutrino oscillation parameters {delta}m{sup 2}{sub o} and sin{sup 2}{theta}{sub o}.

  18. 高纯氖气中微量氦分析的影响因素%Impact factor on trace helium analysis in high purity neon

    Institute of Scientific and Technical Information of China (English)

    姜东; 薛文平; 曲庆; 崔杰; 吴尚达

    2013-01-01

    A series of experiments for trace helium in the industrial high pure neon has been carried out to meet the new requirements of national standards on the content of impurities in pure neon.Three sets of gas chromatography GC-122,GC-14B,and GC-14C were used to measure the same sample,and the influence of current bridge,oven temperature and carrier gas flow on the helium analysis in neon was investigated.The bridge current showed the significant effect on the sensitivity of the detector.Oven temperature and carrier gas flow affected the separation between hydrogen and helium.The air tightness of sample injector and gas path system also is the important factor on theexperimental accuracy.%针对工业上高纯氖气中存在的微量氦,进行了一系列的研究实验,通过考察实验条件探索实验的规律性,以适应国家标准对纯氖中杂质含量的新要求.实验中使用了三台气相色谱GC-122、GC-14B、GC-14C,测量相同样品,并考察了桥电流、柱箱温度、载气体积流量等因素对氖气中氦分析的影响.结果表明,桥电流对检测器灵敏度的影响最为显著,柱温和载气体积流量则影响氢气和氦气的分离.进样器及气路的气密性对实验结果的准确性也存在重要的影响.

  19. Emerging concepts for myocardial late gadolinium enhancement MRI.

    Science.gov (United States)

    Doltra, Adelina; Amundsen, Brage Hoyem; Gebker, Rolf; Fleck, Eckart; Kelle, Sebastian

    2013-08-01

    Late gadolinium enhancement is a useful tool for scar detection, based on differences in the volume of distribution of gadolinium, an extracellular agent. The presence of fibrosis in the myocardium amenable to be detected with late gadolinium enhancement MRI is found not only in ischemic cardiomyopathy, in which it offers information regarding viability and prognosis, but also in a wide variety of non-ischemic cardiomyopathies. In the following review we will discuss the methodological aspects of gadolinium-based imaging, as well as its applications and anticipated future developments.

  20. Production d'isobutène de haute pureté par décomposition du MTBE High-Purity Isobutene Production from Mtbe

    Directory of Open Access Journals (Sweden)

    Meunier P. B.

    2006-11-01

    decomposition is catalyzed by solids with an acid nature. It has mainly been examined on catalysts of the sulfonic-resin type, but solid acid catalysts have recently appeared (zeolites, silica-alumina, supported phosphoric acid, etc. . The different types of catalysts used are examined for the principal reaction and secondary reactions. The formulation of the catalyst and the nature of the active acid sites (Brönsted or Lewis have great influence on the reaction. Data from the literature mainly concern catalysts of the resin type with Brönsted acidity. Concerning catalysts of the oxide type, mention is made of Lewis acid sites catalyzing the principal reaction. The species adsorbed, the mechanisms and kinetic investigations of MTBE decomposition have mainly been examined for sulfonic resins. The most probable mechanisms (mechanism B, page 371 is the following one :(a Ether adsorption on a double center without dissociation. (b Surface reaction between adsorbed ether and a free active center, to give rise to isobutene adsorbed on a double center without dissociation and methanol adsorbed on a single center. This stage is the one that limits the process from the kinetic standpoint. (c Desorption of isobutene and methanol. The corresponding rate equation is given in Table III, and the adsorbed species are given on page . For solid acid catalysts, few data concerning the kinetics are available in the literature. A single equation (Eq. 4, page 371, which was determined experimentally on a gamma-AI2O3 catalyst modified on the surface by silica, is proposed. On a gamma-AI2O3 catalyst, the inhibiting influence of water has been shown for high contents. Secondary reactions are mainly due to the presence of Brönsted acidity. Indeed, the dimerization and trimerization of isobutene involve mechanisms that necessitate going via a carbonium-ion intermediary on Brönsted acid sites (mechanisms on pages 372 and 377. Likewise, the dehydration of methanol is enhanced by the presence of

  1. The effect of incremental gamma-ray doses and incremental neutron fluences upon the performance of self-biased sup 1 sup 0 B-coated high-purity epitaxial GaAs thermal neutron detectors

    CERN Document Server

    Gersch, H K; Simpson, P A

    2002-01-01

    High-purity epitaxial GaAs sup 1 sup 0 B-coated thermal neutron detectors advantageously operate at room temperature without externally applied voltage. Sample detectors were systematically irradiated at fixed grid locations near the core of a 2 MW research reactor to determine their operational neutron dose threshold. Reactor pool locations were assigned so that fast and thermal neutron fluxes to the devices were similar. Neutron fluences ranged between 10 sup 1 sup 1 and 10 sup 1 sup 4 n/cm sup 2. GaAs detectors were exposed to exponential fluences of base ten. Ten detector designs were irradiated and studied, differentiated between p-i-n diodes and Schottky barrier diodes. The irradiated sup 1 sup 0 B-coated detectors were tested for neutron detection sensitivity in a thermalized neutron beam. Little damage was observed for detectors irradiated at neutron fluences of 10 sup 1 sup 2 n/cm sup 2 and below, but signals noticeably degraded at fluences of 10 sup 1 sup 3 n/cm sup 2. Catastrophic damage was appare...

  2. Covalently-bonded grafting of [Ln3(Benzimidazole)4]-arrayed (Ln = Tb, Nd, Yb or Er) complex monomers into PNBE (poly(norbornene)) with highly luminous color-purity green-light or efficient NIR luminescence

    Science.gov (United States)

    Liu, Lin; Fu, Guorui; Feng, Heini; Guan, Jiaqing; Li, Fengping; Lü, Xingqiang; Wong, Wai-Kwok; Jones, Richard A.

    2017-07-01

    Within series of Ln3-grafted polymers Poly({[Ln3(L)4(NO3)6]·(NO3)·(H3O)2}-co-NBE) (Ln = La, 1; Ln = Eu, 2; Ln = Tb, 3; Ln = Nd, 4; Ln = Yb, 5; Ln = Er, 6 or Ln = Gd, 7) obtained from ring-opening metathesis polymerization (ROMP) of norbornene (NBE) with each of allyl-functionalized complex monomers {[Ln3(L)4(NO3)6]·(NO3)·(H3O)2} (HL = 4-allyl-2-(1H-benzo[d]imidazol-2-yl)-6-methoxyphenol), PNBE-assisted effective energy transfer renders Poly(3-co-NBE) Tb3+-centered highly luminous color-purity green-light with an attractive quantum yield of 87% and efficient near-infrared (NIR) luminescence (ΦNdL = 0.61%; ΦYbL = 1.47% and ΦErL = 0.03%) for Nd3+-, Yb3+- or Er3+-grafted polymers.

  3. Detection and Analytical Capabilities for Trace Level of Carbon in High-Purity Metals by Laser-Induced Breakdown Spectroscopy with a Frequency Quintupled 213 nm Nd:YAG Laser

    Directory of Open Access Journals (Sweden)

    Masaki Ohata

    2017-01-01

    Full Text Available The laser-induced breakdown spectroscopy (LIBS with a frequency quintupled 213 nm Nd:YAG laser was examined to the analysis of trace level of carbon (C in high-purity metals and its detection and analytical capabilities were evaluated. Though C signal in a wavelength of 247.9 nm, which showed the highest sensitivity of C, could be obtained from Cd, Ti, and Zn ca. 7000 mg kg−1 C in Fe could not be detected due to the interferences from a lot of Fe spectra. Alternative C signal in a wavelength of 193.1 nm could not be also detected from Fe due to the insufficient laser output energy of the frequency quintupled 213 nm Nd:YAG laser. The depth analysis of C by LIBS was also demonstrated and the C in Cd and Zn was found to be contaminated in only surface area whereas the C in Ti was distributed in bulk. From these results, the frequency quintupled 213 nm Nd:YAG laser, which was adopted widely as a commercial laser ablation (LA system coupled with inductively coupled plasma mass spectrometry (ICPMS for trace element analysis in solid materials, could be used for C analysis to achieve simultaneous measurements for both C and trace elements in metals by LIBS and LA-ICPMS, respectively.

  4. Production Practice of Extraction of High Purity Tellurium Oxide from Multi-Metal Materials%多金属复杂物料提取高纯氧化碲的生产实践

    Institute of Scientific and Technical Information of China (English)

    江城; 简锡明; 王振启; 谢永金

    2015-01-01

    According to production practice, it studied the comprehensive utilization of multi-metal materials copper slag in non-ferrous smelting. Through grinding-room temperature oxidation leaching- sulfur dioxide reduction-catalytic oxidation process, 79.2% high purity tellurium oxide is obtained, silver, copper, bismuth can be separated effectively, gold and other precious metal in the slag can be concentrated.%系统介绍了利用有色冶炼二次资源——多金属物料铜渣提取高纯氧化碲的工艺,明确了经实践验证的工艺流程与操作条件. 生产实践证明, 采用磨料-常温氧化浸出-二氧化硫还原-催化氧化的工艺,可将碲提纯为含碲达79.2%以上的高纯氧化碲,银、铜、铋等金属可以有效分离,渣料中的微量金及其它贵金属可得到富集.

  5. Speciation, liquid-liquid extraction, sequential separation, preconcentration, transport and ICP-AES determination of Cr(III), Mo(VI) and W(VI) with calix-crown hydroxamic acid in high purity grade materials and environmental samples.

    Science.gov (United States)

    Agrawal, Y K; Sharma, K R

    2005-07-15

    A new functionalized calix[6]crown hydroxamic acid is reported for the speciation, liquid-liquid extraction, sequential separation and trace determination of Cr(III), Mo(VI) and W(VI). Chromium(III), molybdenum(VI) and tungsten(VI) are extracted at pH 4.5, 1.5M HCl and 6.0M HCl, respectively with calixcrown hydroxamic acid (37,38,39,40,41,42-hexahydroxy7,25,31-calix[6]crown hydroxamic acid) in chloroform in presence of large number of cations and anions. The extraction mechanism is investigated. The various extraction parameters, appropriate pH/M HCl, choice of solvent, effect of the reagent concentration, temperature and distribution constant have been studied. The speciation, preconcentration and kinetic of transport has been investigated. The maximum transport is observed 35, 45 and 30min for chromium(III), molybdenum(VI) and tungsten(IV), respectively. For trace determination the extracts were directly inserted into the plasma for inductively coupled plasma atomic emission spectrometry, ICP-AES, measurements of chromium, molybdenum and tungsten which increase the sensitivity by 30-fold, with detection limits of 3ngml(-1). The method is applied for the determination of chromium, molybdenum and tungsten in high purity grade ores, biological and environmental samples. The chromium was recovered from the effluent of electroplating industries.

  6. High purity pion beam at TRIUMF

    Energy Technology Data Exchange (ETDEWEB)

    Aguilar-Arevalo, A. [TRIUMF, 4004 Wesbrook Mall, Vancouver, BC, V6T 2A3 (Canada); Blecher, M. [Physics Department, Virginia Tech., Blacksburg, VA 24061 (United States); Bryman, D.A. [Department of Physics and Astronomy, University of British Columbia, Vancouver, BC, V6T 1Z1 (Canada); Comfort, J. [Arizona State University, Tempe, AZ 85287 (United States); Doornbos, J.; Doria, L. [TRIUMF, 4004 Wesbrook Mall, Vancouver, BC, V6T 2A3 (Canada); Hussein, A. [University of Northern British Columbia, Prince George, BC, V2N 4Z9 (Canada); Ito, N. [Physics Department, Osaka University, Toyonaka, Osaka 560-0043 (Japan); Kettell, S. [Brookhaven National Laboratory, Upton, NY 11973-5000 (United States); Kurchaninov, L. [TRIUMF, 4004 Wesbrook Mall, Vancouver, BC, V6T 2A3 (Canada); Malbrunot, C. [Department of Physics and Astronomy, University of British Columbia, Vancouver, BC, V6T 1Z1 (Canada); Marshall, G.M. [TRIUMF, 4004 Wesbrook Mall, Vancouver, BC, V6T 2A3 (Canada); Numao, T. [TRIUMF, 4004 Wesbrook Mall, Vancouver, BC, V6T 2A3 (Canada)], E-mail: toshio@triumf.ca; Poutissou, R.; Sher, A. [TRIUMF, 4004 Wesbrook Mall, Vancouver, BC, V6T 2A3 (Canada); Walker, B. [Department of Physics and Astronomy, University of British Columbia, Vancouver, BC, V6T 1Z1 (Canada); Yamada, K. [Physics Department, Osaka University, Toyonaka, Osaka 560-0043 (Japan)

    2009-10-11

    An extension of the TRIUMF M13 low-energy pion channel designed to suppress positrons based on an energy-loss technique is described. A source of beam channel momentum calibration from the decay {pi}{sup +}{yields}e{sup +}{nu} is also described.

  7. High Purity Pion Beam at TRIUMF

    Energy Technology Data Exchange (ETDEWEB)

    Kettell, S.; Kettell, S.; Aguilar-Arevalo, A.; Blecher, M.; Bryman, D.A.; Comfort, J.; Doornbos, J.; Doria, L.; Hussein, A.; Ito, N.; et al.

    2009-10-11

    An extension of the TRIUMF M13 low-energy pion channel designed to suppress positrons based on an energy-loss technique is described. A source of beam channel momentum calibration from the decay {pi}{sup +} {yields} e{sup +}{nu} is also described.

  8. PREPARATION OF HIGH PURITY MULLITE CERAMICS

    OpenAIRE

    Rodrigo, P.; Boch, P.

    1986-01-01

    Preparation of mullite ceramics by reaction-sintering of alumina silica shows the necessity of favoring densification over mullitisation. Different Al2O3/SiO2 ratios have been studied. The influence of additives, iron oxide and zirconium oxide, has been examined.

  9. Gadolinium deposition within the dentate nucleus and globus pallidus after repeated administrations of gadolinium-based contrast agents - current status

    Energy Technology Data Exchange (ETDEWEB)

    Stojanov, Dragan [University of Nis, Faculty of Medicine, Nis (Serbia); Center for Radiology, Nis (Serbia); Aracki-Trenkic, Aleksandra [Center for Radiology, Nis (Serbia); Benedeto-Stojanov, Daniela [University of Nis, Faculty of Medicine, Nis (Serbia)

    2016-05-15

    Gadolinium-based contrast agents (GBCAs) have been used clinically since 1988 for contrast-enhanced magnetic resonance imaging (CE-MRI). Generally, GBCAs are considered to have an excellent safety profile. However, GBCA administration has been associated with increased occurrence of nephrogenic systemic fibrosis (NSF) in patients with severely compromised renal function, and several studies have shown evidence of gadolinium deposition in specific brain structures, the globus pallidus and dentate nucleus, in patients with normal renal function. Gadolinium deposition in the brain following repeated CE-MRI scans has been demonstrated in patients using T1-weighted unenhanced MRI and inductively coupled plasma mass spectroscopy. Additionally, rodent studies with controlled GBCA administration also resulted in neural gadolinium deposits. Repeated GBCA use is associated with gadolinium deposition in the brain. This is especially true with the use of less-stable, linear GBCAs. In spite of increasing evidence of gadolinium deposits in the brains of patients after multiple GBCA administrations, the clinical significance of these deposits continues to be unclear. Here, we discuss the current state of scientific evidence surrounding gadolinium deposition in the brain following GBCA use, and the potential clinical significance of gadolinium deposition. There is considerable need for further research, both to understand the mechanism by which gadolinium deposition in the brain occurs and how it affects the patients in which it occurs. (orig.)

  10. Advances in Higher Purity Bi Sample Handling

    Institute of Scientific and Technical Information of China (English)

    ZHAO; Qing-zhang; HE; Ming; DONG; Ke-jun; SHEN; Hong-tao; YIN; Xin-yi; WU; Shao-yong; DOU; Liang; WANG; Xiao-ming; YANG; Xu-ran; XU; Yong-ning; LAN; Xiao-xi; PANG; Fang-fang; CAI; Li; JIANG; Shan

    2013-01-01

    Whether the decay rate of a radionuclide can be influenced by its external environment has always been a hot topic in nuclear science.Higher purity sample is very critical for the half-life measurements.Because using higher purity(6N)Bi metal instead of(4N)Bi target,in 210Po production to reduce the impact of radioactive impurity.The annealing process was performed to remove the damage in the lattice

  11. Removal of gadolinium, a neutron poison from the moderator system of nuclear reactors.

    Science.gov (United States)

    Rufus, A L; Kumar, Padma S; Jeena, K; Velmurugan, S

    2017-08-03

    Gadolinium as gadolinium nitrate is used as neutron poison in the moderator system for regulating and controlling the power generation of Pressurized Heavy Water Reactors (PHWR) and proposed to be used in Advanced Heavy Water Reactors (AHWR) owing to its high neutron absorption cross section. Removal of the added gadolinium nitrate (Gd(3+) and NO3(-)) from the system after its intended use is done using ion exchange resins. In the present investigation, attempts have been made to optimize the ion exchange process for generation of low radioactive waste and maximize utilization of the ion exchange resins by employing different types of resins and different modes of operation. The investigations revealed that use of mixed bed (MB) resin column consisting of Strong Acid Cation (SAC) resin and Strong Base Anion (SBA) resin followed by SAC resin column is efficient in removing the Gd(3+) and NO3(-) from the system besides maintaining the pH of the moderator system in the desirable regime, where gadolinium does not get precipitated as its hydroxide. Copyright © 2017 Elsevier B.V. All rights reserved.

  12. The structural response of gadolinium phosphate to pressure

    Science.gov (United States)

    Heffernan, Karina M.; Ross, Nancy L.; Spencer, Elinor C.; Boatner, Lynn A.

    2016-09-01

    Accurate elastic constants for gadolinium phosphate (GdPO4) have been measured by single-crystal high-pressure diffraction methods. The bulk modulus of GdPO4 determined under hydrostatic conditions, 128.1(8) GPa (Kʹ=5.8(2)), is markedly different from that obtained with GdPO4 under non-hydrostatic conditions (160(2) GPa), which indicates the importance of shear stresses on the elastic response of this phosphate. High pressure Raman and diffraction analysis indicate that the PO4 tetrahedra behave as rigid units in response to pressure and that contraction of the GdPO4 structure is facilitated by bending/twisting of the Gd-O-P links that result in increased distortion in the GdO9 polyhedra.

  13. Research and Development for a Gadolinium Doped Water Cherenkov Detector

    CERN Document Server

    Renshaw, Andrew

    2012-01-01

    The proposed introduction of a soluble gadolinium (Gd) compound into water Cherenkov detectors can result in a high efficiency for the detection of free neutrons capturing on the Gd. The delayed 8 MeV gamma cascades produced by these captures, in coincidence with a prompt positron signal, serve to uniquely identify electron antineutrinos interacting via inverse beta decay. Such coincidence detection can reduce backgrounds, allowing a large Gd-enhanced water Cherenkov detector to make the first observation of supernova relic neutrinos and high precision measurements of Japan's reactor antineutrino flux, while still allowing for all current physics studies to be continued. Now, a dedicated Gd test facility is operating in the Kamioka Mine. This new facility houses everything needed to successfully operate a Gd doped water Cherenkov detector. Successful running of this facility will demonstrate that adding Gd salt to SK is both safe for the detector and is capable of delivering the expected physics benefits.

  14. Substitution of gadolinium ethylenediaminetetraacetate with phosphites: towards gadolinium deposit in nephrogenic systemic fibrosis.

    Science.gov (United States)

    Gao, Song; Chen, Mao-Long; Zhou, Zhao-Hui

    2014-01-14

    In neutral media, reactions of gadolinium ethylenediaminetetraacetates with phosphorous acid result in the formation of the mixed-ligand polymeric complex K3n[Gd(EDTA)(HPO3)]n·7nH2O () and dimeric complex Na6[Gd2(EDTA)2(HPO3)2]·2.5NaCl·21H2O () (H4EDTA = ethylenediaminetetraacetic acid) in warm solution. Further substitution with citric acid gives the monomeric gadolinium citrate with EDTA (NH4)2Na[Gd(EDTA)(H2cit)]·4H2O (). The compounds were characterized by elemental analysis, single crystal X-ray diffraction, FT-IR, ESI-MS and thermogravimetric analysis. Structural analysis indicates that three coordinated water molecules in the gadolinium ethylenediaminetetraacetate trihydrates are replaced by phosphite ions (HPO3(2-)) in the compounds and . Gadolinium atoms are octa-coordinated by EDTA and the phosphite ion, the latter links adjacent Gd-EDTA units to generate an infinite one-dimensional chain in compound and a dimeric octatomic ring in . In complex , coordinated water molecules were substituted by the α-hydroxy, α-carboxy and β-carboxy groups of citrate. Citrate is favourable for inhibiting the formation of Gd-EDTA phosphite. All the complexes are very easily soluble in water. The solution behavior of the isostructural lanthanum complexes was probed with (13)C and (31)P NMR spectra in D2O for comparison. ESI-MS analysis and recrystallization proved that complexes and dissociate to the monomeric unit of Gd-EDTA and free HPO3(2-) in aqueous solution. Substitutions of gadolinium ethylenediaminetetraacetates to and are attributed to be the cause of nephrogenic systemic fibrosis in some way.

  15. Gadolinium study for a water Cherenkov detector

    CERN Document Server

    Kibayashi, Atsuko

    2009-01-01

    Modification of large water Cherenkov detectors by addition of gadolinium has been proposed. The large cross section for neutron capture on Gd will greatly improve the sensitivity to antielectron neutrinos from supernovae and reactors. A five-year project to build and develop a prototype detector based on Super-Kamiokande (SK) has started. We are performing various studies, including a material soak test in Gd solution, light attenuation length measurements, purification system development, and neutron tagging efficiency measurements using SK data and a Geant4-based simulation. We present an overview of the project and the recent R&D results.

  16. Neutron Detection Using Gadolinium-Based Diodes

    Science.gov (United States)

    2011-03-01

    U Uranium UNL The University of Nebraska, Lincoln XRD X-Ray Diffraction 1 NEUTRON DETECTION USING GADOLINIUM-BASED DIODES I...detector volume of approximately 3.46x10-6 cm3. 6 4 2 0 2 0.0 0.5 1.0 1.5 2.0 2.5 3.0 Applied BiasV De ple tio nW idt hm  Si SiC 22...Layer deposition on the SiC substrate was confirmed by x-ray diffraction ( XRD ), however, no ellipsometry or other characterization measurements were

  17. 高纯锗(HPGe)γ谱仪测定铀矿石中镭的方法研究%The Experiment Study on the Radium Measurment in Uranium ore with High Purity Germanium(HPGe) γSpectrometer

    Institute of Scientific and Technical Information of China (English)

    薛志伟; 高明明; 乔宁强; 王强; 朱晓贤

    2014-01-01

    为了改善由样品密度不同、厚度不同引起的测量误差,笔者采用压片法制样,然后密封于样品盒达到平衡,通过152 Eu对外界的电磁干扰进行内标校正,在高纯锗( HPGe)γ谱仪上测定铀矿石中镭的含量。测定结果的相对标准偏差( RSD/%)为2.43%,与射气法结果进行比较,相对误差在-5.31%~6.62%之间,方法的精密度和准确度均能满足实际生产需求,可操作性强,简便快速。%In order to reduce the measurement error caused by different sample thickness and density , the author uses compression method to get detection sample .The sample is sealed in a sample box to achieve balance , then we measure the radium content of uranium ore by using High purity germanium (HPGe) γspectrometer. The result is corrected by 152 Eu to avoid the electromagnetic disturbances .The relative standard deviation ( RSD%) of the determination results is 2.43%.Comparing with the emanation method results , the relative error are between -5.31%~6.62%.The method is able to meet the demands due to its advantages of easy operation and rapidness , the high precision and accuracy .

  18. Gadolinium nanoparticles and contrast agent as radiation sensitizers.

    Science.gov (United States)

    Taupin, Florence; Flaender, Mélanie; Delorme, Rachel; Brochard, Thierry; Mayol, Jean-François; Arnaud, Josiane; Perriat, Pascal; Sancey, Lucie; Lux, François; Barth, Rolf F; Carrière, Marie; Ravanat, Jean-Luc; Elleaume, Hélène

    2015-06-01

    The goal of the present study was to evaluate and compare the radiosensitizing properties of gadolinium nanoparticles (NPs) with the gadolinium contrast agent (GdCA) Magnevist(®) in order to better understand the mechanisms by which they act as radiation sensitizers. This was determined following either low energy synchrotron irradiation or high energy gamma irradiation of F98 rat glioma cells exposed to ultrasmall gadolinium NPs (GdNPs, hydrodynamic diameter of 3 nm) or GdCA. Clonogenic assays were used to quantify cell survival after irradiation in the presence of Gd using monochromatic x-rays with energies in the 25 keV-80 keV range from a synchrotron and 1.25 MeV gamma photons from a cobalt-60 source. Radiosensitization was demonstrated with both agents in combination with X-irradiation. At the same concentration (2.1 mg mL(-1)), GdNPS had a greater effect than GdCA. The maximum sensitization-enhancement ratio at 4 Gy (SER4Gy) was observed at an energy of 65 keV for both the nanoparticles and the contrast agent (2.44   ±   0.33 and 1.50   ±   0.20, for GdNPs and GdCA, respectively). At a higher energy (1.25 MeV), radiosensitization only was observed with GdNPs (1.66   ±   0.17 and 1.01   ±   0.11, for GdNPs and GdCA, respectively). The radiation dose enhancements were highly 'energy dependent' for both agents. Secondary-electron-emission generated after photoelectric events appeared to be the primary mechanism by which Gd contrast agents functioned as radiosensitizers. On the other hand, other biological mechanisms, such as alterations in the cell cycle may explain the enhanced radiosensitizing properties of GdNPs.

  19. Dynamics and control designs for internal thermally coupled distillation columns with different purities, Part 1: Open loop dynamic behaviors

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The open loop dynamic behaviors of internal thermally coupled distillation column with four different purities (low-,moderate-, high- and very high-purity) are studied. These dynamic behaviors are characterized by strong asymmetric non-linearity, high sensitivity to operation conditions change and distinct inverse response. With the increase of purity, these dynamic behaviors are intensified and become more complex, which easily lead to the mismatch between linear model and plant and also change the relationship between manipulated and controlled variables.

  20. Synthesis and Characterization of La, Sc, Yb and Nd co-doped Gadolinium doped Cerium (GDC) Composite Electrolyte for IT-SOFC

    Science.gov (United States)

    Damisih; Raharjo, Jarot; Masmui; Setya Aninda, Raffty; Ami Lestari, Novita

    2017-07-01

    Composite based on gadolinium doped cerium (GDC) co-doped Lanthanum (La), Scandium (Sc), Ytterbium (Yb) were investigated as electrolyte for solid oxide fuel cell (SOFC), namely GDC-La, GDC-Sc, GDC-Yb and GDC-Nd, respectively. The second co-doped La, Sc, Yb and Nd ensured the stability and high ionic conductivity of the GDC ceria-based electrolyte materials for SOFC. The GDC powder was synthesized via sol-gel technique. Then the La-GDC, Sc-GDC, Yb-GDC and GDC-Nd were subsequently prepared by mixing the GDC with La, Sc, Yb, and Nd respectively, through solid-state reaction in ballmill at 200rpm alumina balls. The composite electrolytes were then characterized in terms of its morphology, phase and thermal properties of the powders. Among the composite electrolytes investigated, GDC-Yb powder show higher purity and better dispersion than the others co-doped GDC. TGA analysis present that the addition of co-dopant led to improve thermal resistance and stability of solid electrolyte powders. The results confirm that GDC with co-dopant is promising alternative electrolyte for intermediate temperature solid oxide fuel cells (IT-SOFC).

  1. New Technology for Preparation of High Purity Silver by Electrolysis Using Copper-ions Free Electrolyte%无铜离子电解制备高纯银新技术

    Institute of Scientific and Technical Information of China (English)

    王日; 黄绍勇; 聂华平

    2013-01-01

    Aiming at the problems of copper being hard to be further removed from electrolytic silver product ,the electrolytic silver using copper-ions free electrolyte was studied based on the copper ions action mechanism in silver electrolysis process .T he results show that no copper ions but adding reagents A and B in electrolyte ,the conductive properties of electrolyte and precipitation properties of electrolytic silver powder can be obviously improved ,current efficiency increases by 6 .5% ,and high purity silver product in which copper content is lower than 0 .000 5% can be acquired .%针对以电解法生产高纯银过程中杂质铜难以深度去除这一难题,在探明铜离子在银电解过程中的作用机制基础上,研究了以无铜离子电解体系电解银。试验结果表明:电解体系中无铜离子,通过添加试剂A、B,可以明显改善电解液的导电性能和电银粉的析出性能,电流效率提高6.5%,电银粉中铜质量分数低于0.0005%,产品质量符合IC-Ag99.99国家标准。

  2. Study on technology of preparing high-purity α-Al2O3 powder%制备高纯度α-Al2O3粉体的工艺研究

    Institute of Scientific and Technical Information of China (English)

    吴沙沙; 王俊勃; 江燕; 王彦龙; 赵文杰; 杨尔慧

    2015-01-01

    The precursor Al(OH)3 of Al2 O3 were prepared by chemical precipitation with aluminium ni-trate and sal volatile under different concentration of aluminium nitrate,and Al2 O3 powders were getted through calcining precursor at different temperature. The powders were analyzed by the TG-DTG,XRD, BET and SEM. The results showed that the calcination temperature was an important factor to the crystal form of the Al2 O3 powder. The powders with good dispersing were obtained when the concentration of alu-minium nitrate was 0. 1 mol/ L. The sphere-like α-alumina powders with high purity were obtained when the calcination temperature was 1 200 ℃.%以硝酸铝和碳酸铵为原料,采用化学沉淀法,在不同硝酸铝浓度下制备 Al2 O3的前驱体 Al(OH)3,再经不同温度煅烧得到 Al2 O3粉体。利用 TG-DTG、XRD、BET 及 SEM 等分析手段对粉体的性能进行了表征。结果表明,煅烧温度对 Al2 O3的晶型有着重要的影响,硝酸铝浓度为0.1 mol/ L 时制备出的粉体分散性较好,经1200℃煅烧能制备出纯度较高的形貌类似球形的α-Al2 O3粉体。

  3. 高纯钨在瞬态热冲击下的损伤行为研究%Preliminary study on transient thermal shock behavior of high purity tungsten

    Institute of Scientific and Technical Information of China (English)

    陈蕾; 刘翔; 练友运

    2014-01-01

    The thermal shock performances of ITER-like high purity tungsten were examined by an electron beam heat load test and finite element code simulation. Experiments under ITER-like plasma major disruption instability happening condition with test sample background temperature at room temperature were simulated by an electron beam facility EMS-60 newly constructed. Recrystallization, cracking and melting behaviors of test sample after irradiation tests were observed by a scanning electron microscopy (SEM) and their formation mechanisms have been discussed. Finite element simulation has been carried out by ANSYS code and the result shows that the cracking threshold of ITER grade tungsten is about 1.5MJ⋅m-2 for 5ms pulse loading, which is in accordance with experimental results.%通过电子束辐照实验和有限元模拟研究了ITER类型面对等离子体的高纯钨材料在瞬态热冲击下的行为。在新建成的电子束实验平台EMS-60上进行了ITER等离子体发生大破裂不稳定下的模拟实验,实验中样品的基体温度为室温,脉冲宽度为1∼5ms,能量负载范围是1~5MJ⋅m-2。实验后通过扫描电镜观察了样品的再结晶、裂纹及熔化情况,讨论了裂纹形成机理。通过有限元模拟,得出在5ms的脉冲负载下钨的裂纹阈值为1.5MJ⋅m-2,与实验结果符合很好。

  4. Geometry of electromechanically active structures in Gadolinium - doped Cerium oxides

    Energy Technology Data Exchange (ETDEWEB)

    Li, Yuanyuan; Zacharowicz, Renee; Frenkel, Anatoly I., E-mail: igor.lubomirsky@weizmann.ac.il, E-mail: anatoly.frenkel@yu.edu [Physics Department, Yeshiva University, 245 Lexington Avenue, New York, New York 10016 (United States); Kraynis, Olga; Lubomirsky, Igor, E-mail: igor.lubomirsky@weizmann.ac.il, E-mail: anatoly.frenkel@yu.edu [Department of Materials and Interfaces, Weizmann Institute of Science, Rehovot 76100 (Israel); Kas, Joshua [Department of Physics, University of Washington, Seattle, Washington 98195 (United States); Weng, Tsu-Chien; Sokaras, Dimosthenis [Stanford Synchrotron Radiation Lightsource, SLAC National Accelerator Laboratory, Menlo Park, California 94025 (United States)

    2016-05-15

    Local distortions from average structure are important in many functional materials, such as electrostrictors or piezoelectrics, and contain clues about their mechanism of work. However, the geometric attributes of these distortions are exceedingly difficult to measure, leading to a gap in knowledge regarding their roles in electromechanical response. This task is particularly challenging in the case of recently reported non-classical electrostriction in Cerium-Gadolinium oxides (CGO), where only a small population of Ce-O bonds that are located near oxygen ion vacancies responds to external electric field. We used high-energy resolution fluorescence detection (HERFD) technique to collect X-ray absorption spectra in CGO in situ, with and without an external electric field, coupled with theoretical modeling to characterize three-dimensional geometry of electromechanically active units.

  5. Spectroscopic Characterization of Nd-Doped Gadolinium Vanadate Crystals

    Institute of Scientific and Technical Information of China (English)

    马会龙; 臧竞存; 刘玉龙; 朱建慧; 宋雪梅

    2003-01-01

    The Nd3+-doped gadolinium vanadate Nd∶GdVO4 is a new type of crystal with laser properties superior to Nd∶YVO4. Experiment results show that the former has larger absorption cross section (3.261×10-19 cm2) and larger emission cross section (9.283×10-20 cm2). The heat conductivity of Nd∶GdVO4 is similar to that of Nd∶YAG, therefore it is a promising crystal for LD pumped laser. It is used to gain compact, high effect and all solid state lasers. The absorption spectra and fluorescence spectra were reported and the relationship between spectra and crystal structure was analyzed. Characteristics of energy levels of Nd3+ in the Nd∶GdVO4 crystal were discussed. The possibility of achieving laser oscillation at 0.91 μm was discussed.

  6. The use of differential scanning calorimetry for the purity verification of pharmaceutical reference standards.

    Science.gov (United States)

    Mathkar, S; Kumar, S; Bystol, A; Olawoore, K; Min, D; Markovich, R; Rustum, A

    2009-04-05

    Reference standards are routinely used in pharmaceutical industry to determine strength, content, and the quality of drug products, active pharmaceutical ingredients (API), preservatives, antioxidants and excipients. Traditionally, chromatographic techniques such as High Performance Liquid Chromatography (HPLC) and Gas Chromatography (GC) in conjunction with other analytical techniques have been used to determine the purity and strength of a specific lot of a compound for the purpose of qualifying the lot to use as a reference standard. The assigned purity of the reference standard for a wide variety of compounds can be verified using an absolute method such as Differential Scanning Calorimetry (DSC). In this paper, purity of 16 reference standards was determined by DSC and the results were then compared to the purity values that were obtained using HPLC and other analytical techniques. The results indicate that the purity obtained from DSC analysis is comparable to the chromatographic purity for organic compounds that are at least 98% pure. Use of DSC for purity determination is not appropriate if a compound lacks sharp melting point, decomposes in the defined temperature range or exhibits other thermal event(s) which interfere with the melting point of the compound. The use of DSC as an alternative and or complementary method to verify the purity of a compound as part of the pharmaceutical reference standard certification process is discussed.

  7. Low Temperature Spin Structure of Gadolinium Titanate

    Science.gov (United States)

    Javanparast, Behnam; McClarty, Paul; Gingras, Michel

    2012-02-01

    Many rare earth pyrochlore oxides exhibit exotic spin configurations at low temperatures due to frustration. The nearest neighbor coupling between spins on the corner-sharing tetrahedral network generate geometrical magnetic frustration. Among these materials, gadolinium titanate (Gd2Ti2O7) is of particular interest. Its low temperature ordered phases are not yet understood theoretically. Bulk thermal measurements such as specific heat and magnetic susceptibility measurements find two phase transitions in zero external field, in agreement with simple mean field calculations. However, recent neutron scattering experiments suggest a so-called 4-k spin structure for intermediate phase and a so called canted 4-k structure for lower temperature phase that does not agree with either mean-field theory or Monte Carlo simulation which find the 1-k state and Palmer-Chalker state respectively as the lowest free energy configuration for those phases. In our work, we study the 4-k structure in detail and present a new phase diagram for dipolar Heisenberg spins on a pyrochlore lattice, certain portions of which describe gadolinium titanate.

  8. 废铁屑还原软锰矿制备高纯硫酸锰工艺研究%Preparation of High Purity Manganese Sulfate from the Reduction of Pyrolusite Using Scrap Iron as the Reductant

    Institute of Scientific and Technical Information of China (English)

    蔡振勇; 易清风; 刘汉勇; 方明略; 龚学华; 符国庆

    2011-01-01

    研究了采用废铁屑作为还原剂,在稀硫酸介质中湿法还原软锰矿制备硫酸锰的工艺过程.通过单因素实验确定最佳工艺参数,结果表明:当Fe/MnO2的摩尔比为0.78∶1,H2SO4/MnO2的摩尔比为2.1∶1,反应温度50℃,反应时间80 min时,锰的浸出率在95%以上.加入碳酸钙中和调节溶液pH值至5~6,使溶液中的铁、铝等杂质离子水解为氢氧化铁、氢氧化铝等沉淀除去,加入硫化钡使浸出溶液中的重金属离子以硫化物沉淀除去,减压过滤得到硫酸锰粗滤液,向粗滤液中加入二氟化锰使溶液中的Ca2+、Mg2+等离子生成氟化物沉淀,然后溶液经过静置过滤得到硫酸锰净化液,滤液经浓缩、结晶制备硫酸锰产品.经检测产品纯度在99%以上,杂质含量低于国家标准.%In this paper, the leaching of manganese sulfate from pyrolusite with scrap iron as a reductant in dilute sulfuric acid solution was studied. Optimal parameters that affect the leaching efficiency of manganese sulfate were determined by the single factor method. The results shows that the leaching rate of manganese can reach more than 95%under the condition of Fe to MnO2 molar ratio of 0.78, H2SO4 to MnO2 molar ratio of 2.1, reaction temperature 50°C, reaction time 80min. Calcium carbonate was added to the leaching solution to adjust pH 5 ~ 6 so that iron^aluminum and other impurities were removed by becoming iron hydroxide、aluminum hydroxide and other precipitations. Heavy metal ions were removed by adding barium sulfide to the leaching solution to form sulfide precipitations. After being filtrated, manganese difluoride was added to the filtrate to precipitate Ca2+ 、Mg2+ and other impurities. After standing, the solution was then filtrated and high purity manganese sulfate solution was obtained. Crystallized manganese sulfate was obtained after being concentrated. Manganese sulfate purity can reach more than 99% and impurity contents were lower than those

  9. Positive gadolinium anomalies in wastewater treatment plant effluents and aquatic environment in the Hérault watershed (South France).

    Science.gov (United States)

    Rabiet, M; Brissaud, F; Seidel, J L; Pistre, S; Elbaz-Poulichet, F

    2009-05-01

    Anthropogenic gadolinium (Gd), used as a contrast agent in magnetic resonance imaging, may enter rivers and groundwaters with the effluents of wastewater treatment plant (WWTP). Such contaminations, which are mainly found in densely populated areas with highly developed medical systems, induce positive gadolinium anomalies in waters. This study reports on the occurrence of positive Gd anomaly in wastewaters, surface and groundwaters in a slightly populated Mediterranean watershed. Water samples have been collected along the Hérault River, in its tributaries, in wells and springs supplying drinking water and in WWTP effluents during two sampling campaigns in February and July 2003. Systematically pronounced positive gadolinium anomalies (Gd/Gd( *)) were observed in WWTP effluents with values reaching 306. These observations have shown that Gd/Gd( *) can also be found in wastewater drained from rural communities, not equipped with MRI facilities. Positive gadolinium anomalies were detected in two tributaries of the Hérault River and in some wells supplying drinking water, corresponding to an excess of anthropogenic Gd in water up to 15.4pM. A monthly monitoring on one well has confirmed the persistence of gadolinium anomalies all along the year, suggesting a continual wastewater contamination on this site. A spatial monitoring on one tributary showed that wastewater contribution modifies completely the normalized REE pattern of river water, resulting in a decrease of REE amount correlated to the Gd anomaly appearance.

  10. Gadolinium-modified titanium oxide materials for photoenergy applications:a review

    Institute of Scientific and Technical Information of China (English)

    Maciej Zalas

    2014-01-01

    Gadolinium doped titania materials were explored for application in photoenergy production. Incorporation of gadolinium into titania permitted improvement of photocatalytic or photovoltaic performance of the latter. This review provided a deep analysis of gadolinium applications in photoenergy processes and devices with the main focus on explanation of gadolinium doping effect on physicochemical properties of titania.

  11. CIS薄膜太阳能电池吸收层用高纯CuInSe2块体材料的制备%Preparation of High Purity CuInSe2 Alloy for CIS Thin Film Applied in Solar Cell Absorption Layer

    Institute of Scientific and Technical Information of China (English)

    黄小珂; 伍祥武; 谢元锋

    2011-01-01

    以Cu,In,Se为原料制备了高纯CuInSe2块体材料.分别采用熔盐净化-电解-区域熔炼工艺和真空蒸馏-区域熔炼联合工艺对原料In,Se进行提纯,可获得纯度99.9999%In和99.9995%Se.采用多室真空梯度合成工艺,制备出纯度大于99.999%的CuSe、In2Se3中间化合物.将其破碎混匀后压制烧结,合成出的块体材料成分均匀、纯度大于99.999%.XRD分析表明,块体相结构为CuInSe2相.%High purity CuInSe2 material was prepared. Purification process including molten salt refining-electrolysis refining-zone purification and vacuum distillation-zone purification was used to eliminate impurities from raw material In and Se, and In with purity of 99.9999% and Se with purity of 99.9995% were obtained respectively. Intermediate compounds consisted of single phase CuSe and In2Se3 structure, with both purities higher than 99.999% were synthesized by multi-chamber vacuum grads fabrication process. Breaking, milling the intermediate compounds properly, pressing and sintering at proper parameters, then uniform CuInSe2 with purity up to 99.999% was prepared. The alloy mainly consisted of single CuInSe2 phase, analyzing by XRD testing.

  12. FY 1999 results of the regional consortium R and D project/the regional consortium energy R and D. 1st year. Development of the energy-saving type production technology of high-purity/transparent silica glass; 1999 nendo kojundo tomei sekiei glass no sho energy gata seizo gijutsu no kaihatsu seika hokokusho. 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of achieving the remarkable energy conservation, high accuracy and low cost in the production of high-purity/transparent silica glass, the developmental research was conducted on slip casting method. In the development of technology to synthesize silica powder by the sol-gel method, monodisperse - polydisperse high-purity colloidal silica was obtained. In the development of technology to make silica power ultra-highly pure, a process was found out in which silica particles can be obtained by applying moderate amounts of ammonium bicarbonate and aqueous ammonia to the solution of silicic acid for heating. In the slip cast forming, a high-density forming body with a mean particle size of 1.5{mu}m was obtained. In the trial manufacture of reflector model, a translucent silica glass sintered body was obtained by transcribing the gypsum type dimensional shape in high purity. Besides, experimental researches were conducted on the examination of gypsum type/resin type and evaluation of physical properties, heat deterioration characteristics of the actual multi-layer film and trial manufacture of the heat resistant film, analysis/evaluation of trace impurities inside silica glass, conditions for the manufacture of dense silica glass sheets, etc. (NEDO)

  13. 基于光子晶体光纤的高纯度量子关联光子对的制备%Generation of high purity quantum correlated photon pairs based on photonic crystal fiber

    Institute of Scientific and Technical Information of China (English)

    崔亮; 李小英; 李璐

    2012-01-01

    A one-meter-long high nonlinear photonic crystal fiber is pumped by laser pulse train at room temperature, and the generated correlated idler and signal photons are centred at 830 nm and 1411 nm, respectively. The full widths at half maximum of the broad band filters of the two channel are 15 nm and 35 nm, respectively. The fitting results of single channel photon counts reveal that almost all the photons originate from spontaneous four wave mixing and the influence of Raman scattering is eliminated. When the production rate is 0.0085 photon per pulse, the ratio between coincidence rate and accidental coincidence rate is measured to be 102, which not only confirms the low noise property of the photon pair, but also shows that the photon pair are naturally narrow band, and the collecting efficiency in our experiment is high. Moreover, these high purity photon pairs connect different optical bands, and have potential applications in quantum information technologies.%使用脉冲光在室温下抽运一根长1 m的高非线性光子晶体光纤,产生了中心波长分别位于830 nm和1411 nm的具有量子关联性的闲频与信号光子.实验中闲频和信号通道的带宽分别是15 nm和35 nm.对单通道光子计数率的拟合结果显示光子几乎全部来源于光纤中的自发四波混频过程,未受到Raman散射噪声的影响.当闲频和信号通道的光子产生率约为每脉冲0.0085个时,测得符合计数率与随机符合计数率的比值为102,接近理论极限,不仅证明了光子对的低噪声性,而且表明所产生的光子对本身具有窄带频谱特性,因而实验中对其收集效率很高.此外,这种高纯度关联光子对还联接了不同波段,在量子信息技术中有着潜在的应用.

  14. Prognostic Relevance of Tumor Purity and TERT Promoter Mutations on MGMT Promoter Methylation in Glioblastoma.

    Science.gov (United States)

    Schulze Heuling, Eva; Knab, Felix; Radke, Josefine; Eskilsson, Eskil; Martinez-Ledesma, Emmanuel; Koch, Arend; Czabanka, Marcus; Dieterich, Christoph; Verhaak, Roel G; Harms, Christoph; Euskirchen, Philipp

    2017-02-01

    Promoter methylation status of O-6-methylguanine-DNA methyltransferase (MGMT), a DNA repair enzyme, is a critical biomarker in glioblastoma multiforme (GBM) as treatment decisions and clinical trial inclusion rely on its accurate assessment. However, interpretation of results is complicated by poor inter-assay reproducibility as well as weak a correlation between methylation status and expression levels of MGMT. The present study systematically investigates the influence of tumor purity on tissue subjected to MGMT analysis. A quantitative, allele-specific real-time PCR (qAS-PCR) assay was developed to determine genotype and mutant allele frequency of telomerase promoter (pTERT) mutations as a direct measure of tumor purity. We studied tumor purity, pTERT mutation by Sanger sequencing, MGMT methylation by pyrosequencing, IDH1 mutation status, and clinical parameters in a cohort of high-grade gliomas (n=97). The qAS-PCR reliably predicted pTERT genotype and tumor purity compared with independent methods. Tumor purity positively and significantly correlated with the extent of methylation in MGMT methylated GBMs. Extent of MGMT methylation differed significantly with respect to pTERT mutation hotspot (C228T vs. C250T). Interestingly, frontal lobe tumors showed greater tumor purity than those in other locations. Above all, tumor purity was identified as an independent prognostic factor in GBM. In conclusion, we determined mutual associations of tumor purity with MGMT methylation and pTERT mutations and found that the extent of MGMT methylation reflects tumor purity. In turn, tumor purity is prognostic in IDH1 wildtype GBM.

  15. Alkali metal and alkali earth metal gadolinium halide scintillators

    Energy Technology Data Exchange (ETDEWEB)

    Bourret-Courchesne, Edith; Derenzo, Stephen E.; Parms, Shameka; Porter-Chapman, Yetta D.; Wiggins, Latoria K.

    2016-08-02

    The present invention provides for a composition comprising an inorganic scintillator comprising a gadolinium halide, optionally cerium-doped, having the formula A.sub.nGdX.sub.m:Ce; wherein A is nothing, an alkali metal, such as Li or Na, or an alkali earth metal, such as Ba; X is F, Br, Cl, or I; n is an integer from 1 to 2; m is an integer from 4 to 7; and the molar percent of cerium is 0% to 100%. The gadolinium halides or alkali earth metal gadolinium halides are scintillators and produce a bright luminescence upon irradiation by a suitable radiation.

  16. Magnetic resonance imaging using gadolinium-based contrast agents.

    Science.gov (United States)

    Mitsumori, Lee M; Bhargava, Puneet; Essig, Marco; Maki, Jeffrey H

    2014-02-01

    The purpose of this article was to review the basic properties of available gadolinium-based magnetic resonance contrast agents, discuss their fundamental differences, and explore common and evolving applications of gadolinium-based magnetic resonance contrast throughout the body excluding the central nervous system. A more specific aim of this article was to explore novel uses of these gadolinium-based contrast agents and applications where a particular agent has been demonstrated to behave differently or be better suited for certain applications than the other contrast agents in this class.

  17. Dielectric characterization of gadolinium tartrate trihydrate crystals

    Energy Technology Data Exchange (ETDEWEB)

    Want, Basharat [Department of Physics, University of Kashmir, Srinagar 190006, Jammu and Kashmir (India); Ahmad, Farooq [Department of Physics, University of Kashmir, Srinagar 190006, Jammu and Kashmir (India); Kotru, P.N. [Department of Physics and Electronics, University of Jammu, Jammu 180006, Jammu and Kashmir (India)]. E-mail: pn_kotru@yahoo.com

    2007-01-15

    Single crystals of gadolinium tartrate trihydrate have been grown by gel diffusion technique. Single crystal X-ray diffraction analysis shows that the crystals belong to the tetragonal system with non-centrosymmetric space group. The dielectric constant, dielectric loss and ac conductivity have been measured as a function of frequency in the range 1 kHz-5 MHz and temperature range 20-300 deg. C. The dielectric constant increases with temperature, attains a peak around 240 deg. C and then decreases as the temperature exceeds 240 deg. C. The dielectric anomaly at 240 deg. C is suggested to be due to phase transition brought about in the material, which is further supported by the thermal studies. The variation of ac conductivity with temperature has been measured and the material is suggested to show protonic conductivity.

  18. Pristine Purity : New Political Parties in Canada

    NARCIS (Netherlands)

    Lucardie, Anthonie

    2007-01-01

    Success sells better than failure; hence new parties receive very little attention from political scientists as long as they remain marginal and fail to win seats in Parliament. Yet in the margins of the party system, they may maintain the pristine purity of political principles and ideas better tha

  19. Estimating purity in terms of correlation functions

    CERN Document Server

    Prosen, T; Znidaric, M; Prosen, Tomaz; Seligman, Thomas H.; Znidaric, Marko

    2003-01-01

    We prove a rigorous inequality estimating the purity of a reduced density matrix of a composite quantum system in terms of cross-correlation of the same state and an arbitrary product state. Various immediate applications of our result are proposed, in particular concerning Gaussian wave-packet propagation under classically regular dynamics.

  20. Sensitive and transportable gadolinium-core plastic scintillator sphere for neutron detection and counting

    Energy Technology Data Exchange (ETDEWEB)

    Dumazert, Jonathan; Coulon, Romain; Carrel, Frédérick; Corre, Gwenolé; Normand, Stéphane [CEA, LIST, Laboratoire Capteurs Architectures Electroniques, 91191 Gif-sur-Yvette (France); Méchin, Laurence [CNRS, UCBN, Groupe de Recherche en Informatique, Image, Automatique et Instrumentation de Caen, 14050 Caen (France); Hamel, Matthieu [CEA, LIST, Laboratoire Capteurs Architectures Electroniques, 91191 Gif-sur-Yvette (France)

    2016-08-21

    Neutron detection forms a critical branch of nuclear-related issues, currently driven by the search for competitive alternative technologies to neutron counters based on the helium-3 isotope. The deployment of plastic scintillators shows a high potential for efficient detectors, safer and more reliable than liquids, more easily scalable and cost-effective than inorganic. In the meantime, natural gadolinium, through its 155 and mostly 157 isotopes, presents an exceptionally high interaction probability with thermal neutrons. This paper introduces a dual system including a metal gadolinium core inserted at the center of a high-scale plastic scintillator sphere. Incident fast neutrons are thermalized by the scintillator shell and then may be captured with a significant probability by gadolinium 155 and 157 nuclei in the core. The deposition of a sufficient fraction of the capture high-energy prompt gamma signature inside the scintillator shell will then allow discrimination from background radiations by energy threshold, and therefore neutron detection. The scaling of the system with the Monte Carlo MCNPX2.7 code was carried out according to a tradeoff between the moderation of incident fast neutrons and the probability of slow neutron capture by a moderate-cost metal gadolinium core. Based on the parameters extracted from simulation, a first laboratory prototype for the assessment of the detection method principle has been synthetized. The robustness and sensitivity of the neutron detection principle are then assessed by counting measurement experiments. Experimental results confirm the potential for a stable, highly sensitive, transportable and cost-efficient neutron detector and orientate future investigation toward promising axes.

  1. Sensitive and transportable gadolinium-core plastic scintillator sphere for neutron detection and counting

    Science.gov (United States)

    Dumazert, Jonathan; Coulon, Romain; Carrel, Frédérick; Corre, Gwenolé; Normand, Stéphane; Méchin, Laurence; Hamel, Matthieu

    2016-08-01

    Neutron detection forms a critical branch of nuclear-related issues, currently driven by the search for competitive alternative technologies to neutron counters based on the helium-3 isotope. The deployment of plastic scintillators shows a high potential for efficient detectors, safer and more reliable than liquids, more easily scalable and cost-effective than inorganic. In the meantime, natural gadolinium, through its 155 and mostly 157 isotopes, presents an exceptionally high interaction probability with thermal neutrons. This paper introduces a dual system including a metal gadolinium core inserted at the center of a high-scale plastic scintillator sphere. Incident fast neutrons are thermalized by the scintillator shell and then may be captured with a significant probability by gadolinium 155 and 157 nuclei in the core. The deposition of a sufficient fraction of the capture high-energy prompt gamma signature inside the scintillator shell will then allow discrimination from background radiations by energy threshold, and therefore neutron detection. The scaling of the system with the Monte Carlo MCNPX2.7 code was carried out according to a tradeoff between the moderation of incident fast neutrons and the probability of slow neutron capture by a moderate-cost metal gadolinium core. Based on the parameters extracted from simulation, a first laboratory prototype for the assessment of the detection method principle has been synthetized. The robustness and sensitivity of the neutron detection principle are then assessed by counting measurement experiments. Experimental results confirm the potential for a stable, highly sensitive, transportable and cost-efficient neutron detector and orientate future investigation toward promising axes.

  2. Process design and equipment selection of a 30kt/a high-purity sodium bisulphite plant%30kt/a高纯度亚硫酸氢钠装置的工艺设计与设备选型

    Institute of Scientific and Technical Information of China (English)

    徐晓燕

    2012-01-01

    Process and equipment selection of a 30 kt/a high-purity sodium bisulphite plant are described. The plant used 7.5% SO2 gas at 70 - 80 ℃ and 20 wt% NaOH solution as raw materials to produce 35 wt% highpurity sodium bisulphate through 3 stage absorption reaction. The plant has operated stably for more than 9 months and every index reached or exceeded design value. The product contained 35.3 wt% NaHSO3 , 0.42 wt% NaESO4 ,30.48 wt% Na2SO3, 0.01 wt% NaC1, 0. 000 4 wt% Fe and 0. 018 wt% water insoluble matter and had pH value of 3.6 - 4.0. The SO2 content of tail-gas from absorption was only 200 mg/m3.%介绍了某厂30kt/a高纯度亚硫酸氢钠装置工艺流程和设备选型情况。该装置以70~80℃、φ(SO2)7.5%的SO2烟气和训(NaOH)约20%氢氧化钠溶液为原料,经3级吸收反应制得W(NaHS03)35%的高纯度亚硫酸氢钠溶液产品。该装置已稳定运行9个多月时间,各项指标均达到或超过设计值,产品中叫(NaHSO3)35.3%,W(Na2SO4)0.42%,W(Na2SO3)0.48%,w(NaCl)0.01%,w(Fe)0.0004%,水不溶物(W)0.018%,pH值3.6~4.0。吸收后,尾气ρ(SO2)仅200mg/m^3。

  3. Study on removal of silicon and preparation of high purity ferric oxide red from acid leaching filtrate of tailings%尾矿酸浸液除硅以及制备高纯铁红的研究

    Institute of Scientific and Technical Information of China (English)

    廖攀; 陈学安; 常新安; 肖卫强; 王少华

    2012-01-01

    Acid leaching filtrate of tailings from Jinchuan Company contains not only large amount of Fe2+ but also small amount of Si4*.Using CaO as neutralizer and polyacrylamide as flocculation reagent,the optimum technological conditions of removal of silicon from the acid leaching filtrate were obtained by orthogonal experiments.After silicon was removed,goethite was prepared under the conditions of 85 t and stirring by using MgO as neutralizer and air together with H2O2 as nxirlant.Finally the high purity ferric oxide red (a-Fe2O3) was prepared by calcining goethite at calcining temperature of 800℃ for 2 h followed by washing with 5% dilute HNO3. The mass fraction of main content of the as-prepared iron red was 99.2% .which could be classified as the qualified product according to the national standard of HG/T 2574?009.%金川公司尾矿酸浸液中除含有较高含量的铁之外,还含有一定量的杂质硅.以氧化钙为中和剂,聚丙烯酰胺为絮凝剂,通过正交设计与实验,得出了从该酸浸液中除硅的较佳工艺条件;随后,以氧化镁为中和剂,空气和双氧水为氧化剂,将除硅后滤液在85℃搅拌加热,制得针铁矿沉淀;最后将沉淀在800℃煅烧2h并经过5%稀硝酸洗涤得到了高纯铁红,其主成分质量分数为99.2%,符合HG/T 2574-2009工业氧化铁国家标准.

  4. High-purity control of internal thermally coupled distillation columns based on nonlinear Wave model%基于非线性Wave模型的内部热耦合塔高纯控制方案

    Institute of Scientific and Technical Information of China (English)

    丛琳; 刘兴高; 周叶翔

    2012-01-01

    为了解决高纯内部热耦合精馏塔( ITCDIC)的强非线性特性给控制器的设计带来较大困难的问题,将非线性Wave理论运用到内部热耦合精馏塔的控制设计中.首先根据浓度曲线的特性提出了浓度波形的描述函数.其次根据波形描述函数以及物料守恒关系推导出波速公式.最后将Wave理论与一般模型控制(GMC)结合起来,建立了基于Wave模型的一般模型控制(WGMC).在苯-甲苯物系的实例研究中与传统的基于数据模型的一般模型控制(TGMC)进行比较.研究结果表明,WGMC在伺服控制和干扰控制的表现都明显优于TGMC,WGMC控制方案较传统的一般模型控制方案更加稳定可靠.%To solve the problem that high-purity internal thermally coupled distillation columns (ITCDIC) present strong nonlinear dynamics which troubles the controller design, nonlinear wave theory is introduced into the control design of ITCDIC. First, the describing function of the profile of concentration is proposed according to the characteristics of the concentration curve. Then, the wave velocity is derived from describing function of the concentration profile and component mass balance of each stage. Finally, combining the Wave model with the generic model control (GMC) a generic model control based on the Wave model (WGMC) is proposed. Compared with data-based generic model control (TGMC) in benzene-toluene system, WGMC performs more excellently both in servo control and regulatory control and it is more stable and efficient than the generic model control scheme.

  5. Efficacy of a high-purity factor IX concentrate in hemophilia B patients undergoing surgery Eficácia do concentrado de alta pureza do fator IX em pacientes cirúrgicos portadores de hemofilia B

    Directory of Open Access Journals (Sweden)

    Vesa Rasi

    2002-04-01

    Full Text Available A plasma derived, high purity, solvent-detergent treated and subsequently nanofiltered factor IX concentrate (BEMOFIL was evaluated in 19 hemophilia B patients, including four with severe, thirteen with mild or moderate type of disease and two hemophilia B carriers undergoing 31 surgical procedures. The mean in vivo recovery was 52 %, range 36 - 76 %. The mean preoperative plasma factor IX activity after the initial loading dose was 0.86 IU mL-1, range 0.59 - 1.32 IU mL-1. In eight major orthopedic procedures, the mean usage of factor IX was 44600 IU or 574 IU kg-1 during the hospital stay, mean 11.6 days. Thromboprophylaxis was not used. The hemostatic efficacy was evaluated good in all cases and there were no thromboembolic complications. In conclusion, BEMOFIL used as bolus dosing was found to be safe and effective in achieving hemostasis in subjects with hereditary F IX deficiency undergoing surgery.O concentrado de fator IX ( Bemofil , um derivado plasmático de alta pureza tratado com solventes- detergente e nano-filtrado , foi avaliado em 19 pacientes portadores de Hemofilia B .Quatro pacientes apresentavam a forma grave da moléstia, 13 a forma leve e moderada e dois portadores em um total de 31 atos cirúrgicos.A recuperação média "in vivo" foi de 52% (36-76%. A atividade plasmática média pré-operatória do fator IX após a dose inicial foi de 0,86 UI ml -1 , média de 0,59 - 1,32 UI ml-1. Em oito procedimentos ortopédicos extensos , a média de utilização do fator IX foi de 44.600 UI ou 574 UI kg -1 durante a hospitalização que teve a média de 11,6 dias. A tromboprofilaxia não foi utilizada. A eficácia hemostática avaliada em todos os casos foi boa ,e não ocorreu nenhum tipo de complicação tromboembólica. Concluímos que o Bemofil em bolus foi considerado seguro e eficaz para a hemostasia em pacientes portadores de hemofilia B que necessitam de um procedimento cirúrgico.

  6. Gadolinium recovery from aqueous pharmaceutical residuals by pulsed electrical discharge; Rueckgewinnung von Gadolinium aus pharmazeutischen Abwaessern mittels gepulster elektrischer Entladung

    Energy Technology Data Exchange (ETDEWEB)

    Lorenz, Tom; Froehlich, Peter [TU Bergakademie Freiberg (Germany); Seifert, Martin; Jacob-Seifert, Karin [FNE Entsorgungsdienste GmbH, Freiberg (Germany)

    2017-02-15

    Advanced oxidation process (AOP) is an oxidation step releasing reactive oxygen species by pulsed electrical discharge in aqueous systems. In contrast to processes generating ozone by external UV radiation this method is feasible for turbid liquids with solid particles. This method is currently used in particular in the field of purification of chemically polluted waste waters. In the present application AOP is applied for partial degradation of the organic ligand system of a gadolinium X-ray contrast agent to separate gadolinium subsequently by adding caustic soda to precipitate > 99% of gadolinium.

  7. A modified method for isolating mouse islets of an adequate quality, quantity, and purity.

    Science.gov (United States)

    Xu, Jiejie; Peng, Baogang; Zhang, Caiyun; Xu, Jiwei; Ma, Yi; Lu, Xinjun

    2017-08-01

    Mouse islets are widely used in diabetes research. Thus an adequate quality, quantity, and purity of islets are needed for high-quality investigations. We performed a combination of filtration and density gradient separation and optimized many steps in the islet isolation procedure, including perfusion, digestion, and purification. Our results show that an increased quality, quantity, and purity of isolated islets can be achieved using these modifications. Moreover, this method can guarantee maximal recovery and purity of the isolated islets and is easy to perform with practice.

  8. Gadolinium-Based GaN for Neutron Detection with Gamma Discrimination

    Science.gov (United States)

    2016-06-01

    from evaluating these detectors are summarized as, 1) semi-insulating GaN [1] does not show radiation response due to the high density carrier...Praneeth Kandlakunta, 2012 2) “ Evaluation of GaN as a Radiation Detection Material “, Jinghui Wang, 2012 Journal Articles: 1) P. Kandlakunta... Evaluation of GaN as a Radiation Detection Material. Thesis,The Ohio State University, 2012. 8. Kandlakunta, P., Gamma Rays Rejection in a Gadolinium based

  9. Simulation and Design of Multi-modulars Detector System of Gadolinium-Loaded Liquid Scintillator

    Institute of Scientific and Technical Information of China (English)

    HOU; Long; WANG; Zhao-hui; YU; Guo-liang; WANG; Qi; KANG; Guo-guo; SU; Xiao-bin; ZHANG; Xiao-peng; ZHANG; Kai

    2012-01-01

    <正>The gadolinium-loaded liquid scintillator has the superiority of high detecting efficiency, and it can be used to measure many kinds of nucleus. We improved this technique and construct a 4π liquid scintillator detecting systems which is composed by many liquid scintillators. By coupling with fission chamber, we form a novel research platform which can be used to measure the (n, 2n) and (n, 3n) cross sections of many nuclei.

  10. Gadolinium EUV Multilayers for Solar Imaging Near 60 nm Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to develop and commercialize a new class of extreme ultraviolet (EUV) multilayer coatings containing the rare-earth element gadolinium (Gd), designed as...

  11. Gadolinium EUV Multilayers for Solar Imaging Near 60 nm Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to develop and commercialize a new class of extreme ultraviolet (EUV) multilayer coatings containing the rare-earth element gadolinium (Gd), designed as...

  12. Deposit of isotopically modified gadolinium suitable to detect solar neutrinos

    Energy Technology Data Exchange (ETDEWEB)

    Cribier, M

    1999-04-01

    Consideration on the possibility to find gadolinium with a modified isotopic composition are envisaged, in particular with respect to the important use of this element by the nuclear energy. These possibility could exist in the far future. (author)

  13. The effect of demagnetization on the magnetocaloric properties of gadolinium

    DEFF Research Database (Denmark)

    Bahl, Christian Robert Haffenden; Nielsen, Kaspar Kirstein

    2009-01-01

    Gadolinium displays a strong magnetocaloric effect at temperatures close to room temperature making it useful in the field of room temperature magnetic refrigeration. We discuss the importance of including the effects of the demagnetization field when considering the magnetocaloric properties...

  14. Nephrogenic systemic fibrosis and gadolinium-based contrast media

    DEFF Research Database (Denmark)

    Thomsen, Henrik S; Morcos, Sameh K; Almén, Torsten

    2012-01-01

    PURPOSE: To update the guidelines of the Contrast Media Safety Committee (CMSC) of the European Society of Urogenital Radiology (ESUR) on nephrogenic systemic fibrosis and gadolinium-based contrast media. AREAS COVERED: Topics reviewed include the history, clinical features and prevalence...... of nephrogenic systemic fibrosis and the current understanding of its pathophysiology. The risk factors for NSF are discussed and prophylactic measures are recommended. The stability of the different gadolinium-based contrast media and the potential long-term effects of gadolinium in the body have also been...... reviewed. KEY POINTS : • Clinical features, risk factors and prevention of nephrogenic systemic fibrosis are reviewed • Patients with GFR below 30 ml/min/1.73 m ( 2 ) have increased risk of developing NSF • Low stability gadolinium contrast media show the strongest association with NSF • Following...

  15. Inference of conversion and purity for ETBE reactive distillation

    Directory of Open Access Journals (Sweden)

    Tian Yu-Chu

    2000-12-01

    Full Text Available Reactive distillation (RD, an unconventional and attractive technique, has been applied in fuel ether production. A typical application of RD is the synthesis of the widely used methyl tert-butyl ether (MTBE. RD has also been found to have potential to produce high quality ethyl tert-butyl ether (ETBE, a potential alternative to MTBE. A RD process integrates conventional reaction and separation into a single unit, resulting in extra complexity and dual process objectives, i.e. maximization of reactant conversion and purity of products. The conversion and the purity are thus important variables to be controlled in RD of ETBE. Unfortunately, both of them are not economically and reliably available for closed-loop control. This study aims to develop an effective method to infer the conversion and the purity from multiple temperature measurements that are easily available on-line and in real time. Nonlinear inferential models are recommended for ETBE synthesis with a ten-stage pilot scale RD column. The models are two-variable third-order regressive models, in which the temperature measurements of the reboiler and the bottom reactive section are employed. Experimental design, model identification, and model testing are also investigated.

  16. Impurities especially titanium in the rare earth metal gadolinium-before and after solid state electrotransport

    Institute of Scientific and Technical Information of China (English)

    苗睿瑛; 张小伟; 朱琼; 张志琦; 王志强; 颜世宏; 陈德宏; 周林; 李宗安

    2014-01-01

    Gadolinium was prepared by conventional procedures of fluorination, reduction, distillation and solid state electrotransport (SSE). The electronegativities of the metals were found to have an important influence on the electrotransport process and result of the impurity element. Meanwhile, titanium particles in the distilled gadolinium as major metallic impurities were studied by high resolution transmission electron microscopy (HRTEM) before and after solid state electrotransport. The results showed that impurities especially titanium transported from anode to cathode during SSE. In the metal before SSE, there were impurities of titanium in strip shape or embedded round shape. After SSE processing, titanium particles in the metal smaller than 50 nm in the cathode, but existed 6 to 10 times bigger in the anode.

  17. The statistical decay properties of Gadolinium isotopes using the DANCE array

    Science.gov (United States)

    Dashdorj, D.; Mitchell, G.; Baramsai, B.; Chankova, R.; Chyzh, A.; Walker, C.

    2008-10-01

    The gadolinium isotopes are interesting for reactor applications as well as for medicine and astrophysics. There are seven stable isotopes of gadolinium with varying deformation. Decay γ rays following neutron capture on Gd isotopes are detected by the DANCE array, which is located at flight path 14 at the Lujan Neutron Scattering Center at Los Alamos National Laboratory. The high segmentation and close packing of the detector array enable γ-ray multiplicity measurements. The calorimetric property of the DANCE array coupled with the neutron time-of-flight technique enables one to gate on a specific resonance of a specific isotope in the time-of-flight spectrum and obtain the summed energy spectrum for that isotope. The singles γ-ray spectrum for each multiplicity can be separated by their DANCE cluster multiplicity. Various photon strength function models are used for comparison with experimentally measured DANCE data and provide insight for understanding the statistical decay properties of deformed nuclei.

  18. Hydrothermal synthesis and characterization of polycrystalline gadolinium aluminum perovskite (GdAlO3, GAP

    Directory of Open Access Journals (Sweden)

    N. Girish H.

    2015-06-01

    Full Text Available Gadolinium aluminum perovskite (GdAlO3, GAP is a promising high temperature ceramic material, known for its wide applications in phosphors. Polycrystalline gadolinium aluminum perovskites were synthesized using a precursor of co-precipitate gel of GdAlO3 by employing hydrothermal supercritical fluid technique under pressure and temperature ranging from 150 to 200 MPa and 600 to 700 °C, respectively. The resulted products of GAP were studied using the characterization techniques, such as powder X-ray diffraction analysis (XRD, infrared spectroscopy (IR, scanning electron microscopy (SEM and energy dispersive analysis of X-ray (EDX. The X-ray diffraction pattern matched well with the reported orthorhombic GAP pattern (JCPDS-46-0395.

  19. The Effect of Pressure and Temperature on Separation of Free Gadolinium(III) From Gd-DTPA Complex by Nanofiltration-Complexation Method

    Science.gov (United States)

    Rahayu, Iman; Anggraeni, Anni; Ukun, MSS; Bahti, Husein H.

    2017-05-01

    Nowdays, the utilization of rare earth elements has been carried out widely in industry and medicine, one of them is gadolinium in Gd-DTPA complex is used as a contrast agent in a magnetic resonance imaging (MRI) diagnostic to increase the visual contrast between normal tissue and diseased. Although the stability of a given complex may be high enough, the complexation step couldnot have been completed, so there is possible to gadolinium(III) in the complex compound. Therefore, the function of that compounds should be dangerous because of the toxicity of gadolinium(III) in human body. So, it is necessarry to separate free gadolinium(III) from Gd-DTPA complex by nanofiltration-complexation. The method of this study is complexing of Gd2O3 with DTPA ligand by reflux and separation of Gd-DTPA complex from gadolinium(III) with a nanofiltration membrane on the variation of pressures(2, 3, 4, 5, 6 bars) and temperature (25, 30, 35, 40 °C) and determined the flux and rejection. The results of this study are the higher of pressures and temperatures, permeation flux are increasing and ion rejections are decreasing and gave the free gadolinium(III) rejection until 86.26%.

  20. Specific lipase-responsive polymer-coated gadolinium nanoparticles for MR imaging of early acute pancreatitis.

    Science.gov (United States)

    Zhang, Hong-Wu; Wang, Li-Qin; Xiang, Qing-Feng; Zhong, Qian; Chen, Lu-Ming; Xu, Cai-Xia; Xiang, Xian-Hong; Xu, Bo; Meng, Fei; Wan, Yi-Qian; Deng, David Y B

    2014-01-01

    Currently, available methods for diagnosis of acute pancreatitis (AP) are mainly dependent on serum enzyme analysis and imaging techniques that are too low in sensitivity and specificity to accurately and promptly diagnose AP. The lack of early diagnostic tools highlights the need to search for a highly effective and specific diagnostic method. In this study, we synthesized a conditionally activated, gadolinium-containing, nanoparticle-based MRI nanoprobe as a diagnostic tool for the early identification of AP. Gadolinium diethylenetriaminepentaacetic fatty acid (Gd-DTPA-FA) nanoparticles were synthesized by conjugation of DTPA-FA ligand and gadolinium acetate. Gd-DTPA-FA exhibited low cytotoxicity and excellent biocompatibility when characterized in vitro and in vivo studies. L-arginine induced a gradual increase in the intensity of the T1-weighted MRI signal from 1 h to 36 h in AP rat models. The increase in signal intensity was most significant at 1 h, 6 h and 12 h. These results suggest that the Gd-DTPA-FA as an MRI contrast agent is highly efficient and specific to detect early AP.