Evaluating high pH for control of dreissenid mussels

Directory of Open Access Journals (Sweden)

Dave Evans

2013-04-01

Full Text Available Two field experiments were carried out using a custom built flow-through laboratory to test the effect of elevated pH on dreissenid musselsas a potential control method. Both experiments tested the ability of dreissenid pediveligers to settle under conditions of elevated pH and thelong-term survival of adult dreissenids under the same conditions. The two experimental sites had different water quality and differentspecies of dreissenids present. The settlement of quagga mussel pediveligers at the lower Colorado River was inhibited with increasing pH.At the maximum achieved pH of 9.1, there was approximately 90% reduction compared to the maximum settlement observed in the controls.Since the settlement was almost as low in pH 8.9 as at pH 9.1, the inhibition in settlement may have been due to the presence of a precipitateformed under high pH conditions rather than the increase in background pH. No mortality of quagga mussel adults was observed in theexperimental pH levels at the lower Colorado River. At San Justo Reservoir, zebra mussel settlement decreased with increasing pH. Newsettlement was almost entirely absent at the highest pH tested (pH 9.6. The observed mortality of adult zebra mussels was low, but did tendto increase with increasing pH. We also tested the response of adult zebra mussels to short-term exposure to very high pH levels (i.e. pH 10,11, and 12. Adult mussels in poor physical condition experienced 90% mortality after 12 hours at pH 12. For unstressed adult zebra mussels,90% mortality was reached after 120 hours at pH 12. Significant mortalities were also observed both at pH 10 and pH 11. From this study,we conclude that pH elevation could be used both as a preventative treatment to eliminate settlement by dreissenid mussels and as an end ofseason treatment to eliminate adults. The high pH treatment would have to be tailored to the site water quality to prevent formation ofprecipitate during treatment and to minimize corrosive

Aerosol pH buffering in the southeastern US: Fine particles remain highly acidic despite large reductions in sulfate

Science.gov (United States)

Weber, R. J.; Guo, H.; Russell, A. G.; Nenes, A.

2015-12-01

pH is a critical aerosol property that impacts many atmospheric processes, including biogenic secondary organic aerosol formation, gas-particle phase partitioning, and mineral dust or redox metal mobilization. Particle pH has also been linked to adverse health effects. Using a comprehensive data set from the Southern Oxidant and Aerosol Study (SOAS) as the basis for thermodynamic modeling, we have shown that particles are currently highly acidic in the southeastern US, with pH between 0 and 2. Sulfate and ammonium are the main acid-base components that determine particle pH in this region, however they have different sources and their concentrations are changing. Over 15 years of network data show that sulfur dioxide emission reductions have resulted in a roughly 70 percent decrease in sulfate, whereas ammonia emissions, mainly link to agricultural activities, have been largely steady, as have gas phase ammonia concentrations. This has led to the view that particles are becoming more neutralized. However, sensitivity analysis, based on thermodynamic modeling, to changing sulfate concentrations indicates that particles have remained highly acidic over the past decade, despite the large reductions in sulfate. Furthermore, anticipated continued reductions of sulfate and relatively constant ammonia emissions into the future will not significantly change particle pH until sulfate drops to clean continental background levels. The result reshapes our expectation of future particle pH and implies that atmospheric processes and adverse health effects linked to particle acidity will remain unchanged for some time into the future.

High-performance liquid chromatography of oligoguanylates at high pH

Science.gov (United States)

Stribling, R.; Deamer, D. (Principal Investigator)

1991-01-01

Because of the stable self-structures formed by oligomers of guanosine, standard high-performance liquid chromatography techniques for oligonucleotide fractionation are not applicable. Previously, oligoguanylate separations have been carried out at pH 12 using RPC-5 as the packing material. While RPC-5 provides excellent separations, there are several limitations, including the lack of a commercially available source. This report describes a new anion-exchange high-performance liquid chromatography method using HEMA-IEC BIO Q, which successfully separates different forms of the guanosine monomer as well as longer oligoguanylates. The reproducibility and stability at high pH suggests a versatile role for this material.

High electron mobility InN

International Nuclear Information System (INIS)

Jones, R. E.; Li, S. X.; Haller, E. E.; van Genuchten, H. C. M.; Yu, K. M.; Ager, J. W. III; Liliental-Weber, Z.; Walukiewicz, W.; Lu, H.; Schaff, W. J.

2007-01-01

Irradiation of InN films with 2 MeV He + ions followed by thermal annealing below 500 deg. C creates films with high electron concentrations and mobilities, as well as strong photoluminescence. Calculations show that electron mobility in irradiated samples is limited by triply charged donor defects. Subsequent thermal annealing removes a fraction of the defects, decreasing the electron concentration. There is a large increase in electron mobility upon annealing; the mobilities approach those of the as-grown films, which have 10 to 100 times smaller electron concentrations. Spatial ordering of the triply charged defects is suggested to cause the unusual increase in electron mobility

Acetate biodegradation by anaerobic microorganisms at high pH and high calcium concentration

International Nuclear Information System (INIS)

Yoshida, Takahiro

2011-01-01

Acetate biodegradation at a high pH and a high calcium concentration was examined to clarify the effect of bacterial activity on the migration of organic 14 C compounds in cementitious repositories. Tamagawa river sediment or Teganuma pond sediment was anaerobically cultured with 5 mM acetate and 10 mM nitrate at pH 9.5-12 at 30 o C. After 20 and 90 days, the acetate concentration of the culture medium was analyzed and found to have decreased below 5 mM at pH ≤ 11. On the other hand, it did not decrease when either sediment was incubated in the absence of nitrate. These results suggest that nitrate-reducing bacteria can biodegrade acetate under more alkaline conditions than the reported pH range in which nitrate-reducing bacteria can exhibit activity. Acetate biodegradation was also examined at a high calcium concentration. Sediments were anaerobically cultured at pH 9.5 with 5 mM acetate and 10 mM nitrate in solution, equilibrated with ordinary Portland cement hydrate, in which the Ca concentration was 14.6 mM. No decrease in acetate concentration after incubation of the sediments was observed, nor was it lower than in the absence of cementitious composition, suggesting that kinetics of acetate biodegradation by anaerobic microorganisms is lowered by a high Ca concentration. - Research highlights: → Acetate biodegradation at a high pH and a high calcium concentration was examined to clarify the effect of bacterial activity on the migration of organic 14 C compounds in cementitious repositories. → Nitrate-reducing bacteria can biodegrade acetate at pH ≤ 11. → Kinetics of acetate biodegradation by anaerobic microorganisms might be lowered by a high Ca concentration.

Pressure pressure-balanced pH sensing system for high temperature and high pressure water

International Nuclear Information System (INIS)

Tachibana, Koji

1995-01-01

As for the pH measurement system for high temperature, high pressure water, there have been the circumstances that first the reference electrodes for monitoring corrosion potential were developed, and subsequently, it was developed for the purpose of maintaining the soundness of metallic materials in high temperature, high pressure water in nuclear power generation. In the process of developing the reference electrodes for high temperature water, it was clarified that the occurrence of stress corrosion cracking in BWRs is closely related to the corrosion potential determined by dissolved oxygen concentration. As the types of pH electrodes, there are metal-hydrogen electrodes, glass electrodes, ZrO 2 diaphragm electrodes and TiO 2 semiconductor electrodes. The principle of pH measurement using ZrO 2 diaphragms is explained. The pH measuring system is composed of YSZ element, pressure-balanced type external reference electrode, pressure balancer and compressed air vessel. The stability and pH response of YSZ elements are reported. (K.I.)

Mobility of organic carbon from incineration residues

International Nuclear Information System (INIS)

Ecke, Holger; Svensson, Malin

2008-01-01

Dissolved organic carbon (DOC) may affect the transport of pollutants from incineration residues when landfilled or used in geotechnical construction. The leaching of dissolved organic carbon (DOC) from municipal solid waste incineration (MSWI) bottom ash and air pollution control residue (APC) from the incineration of waste wood was investigated. Factors affecting the mobility of DOC were studied in a reduced 2 6-1 experimental design. Controlled factors were treatment with ultrasonic radiation, full carbonation (addition of CO 2 until the pH was stable for 2.5 h), liquid-to-solid (L/S) ratio, pH, leaching temperature and time. Full carbonation, pH and the L/S ratio were the main factors controlling the mobility of DOC in the bottom ash. Approximately 60 weight-% of the total organic carbon (TOC) in the bottom ash was available for leaching in aqueous solutions. The L/S ratio and pH mainly controlled the mobilization of DOC from the APC residue. About 93 weight-% of TOC in the APC residue was, however, not mobilized at all, which might be due to a high content of elemental carbon. Using the European standard EN 13 137 for determination of total organic carbon (TOC) in MSWI residues is inappropriate. The results might be biased due to elemental carbon. It is recommended to develop a TOC method distinguishing between organic and elemental carbon

Analytical Enantioseparation of β-Substituted-2-Phenylpropionic Acids by High-Performance Liquid Chromatography with Hydroxypropyl-β-Cyclodextrin as Chiral Mobile Phase Additive.

Science.gov (United States)

Tong, Shengqiang; Zhang, Hu; Yan, Jizhong

2016-04-01

Analytical enantioseparation of five β-substituted-2-phenylpropionic acids by high-performance liquid chromatography with hydroxypropyl-β-cyclodextrin (HP-β-CD) as chiral mobile phase additive was established in this paper, and chromatographic retention mechanism was studied. The effects of various factors such as the organic modifier, different ODS C18 columns and concentration of HP-β-CD were investigated. The chiral mobile phase was composed of methanol or acetonitrile and 0.5% triethylamine acetate buffer at pH 3.0 added with 25 mmol L(-1) of HP-β-CD, and baseline separations could be reached for all racemates. As for chromatographic retention mechanism, it was found that there was a negative correlation between the concentration of HP-β-CD in mobile phase and the retention factor under constant pH value and column temperature. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Ionic liquid as a mobile phase additive in high-performance liquid chromatography for the simultaneous determination of eleven fluorescent whitening agents in paper materials.

Science.gov (United States)

Wang, Qing; Chen, Xianbo; Qiu, Bin; Zhou, Liang; Zhang, Hui; Xie, Juan; Luo, Yan; Wang, Bin

2016-04-01

In the present study, 11 4,4'-diaminostilbene-2,2'-disulfonic acid based fluorescent whitening agents with different numbers of sulfonic acid groups were separated by using an ionic liquid as a mobile phase additive in high-performance liquid chromatography with fluorescence detection. The effects of ionic liquid concentration, pH of mobile phase B, and composition of mobile phase A on the separation of fluorescent whitening agents were systematically investigated. The ionic liquid tetrabutylammonium tetrafluoroborate is superior to tetrabutylammomnium bromide for the separation of the fluorescent whitening agents. The optimal separation conditions were an ionic liquid concentration at 8 mM and the pH of mobile phase B at 8.5 with methanol as mobile phase A. The established method exhibited low limits of detection (0.04-0.07 ng/mL) and wide linearity ranges (0.30-20 ng/mL) with high linear correlation coefficients from 0.9994 to 0.9998. The optimized procedure was applied to analyze target analytes in paper samples with satisfactory results. Eleven target analytes were quantified, and the recoveries of spiked paper samples were in the range of 85-105% with the relative standard deviations from 2.1 to 5.1%. The obtained results indicated that the method was efficient for detection of 11 fluorescent whitening agents. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Atomic structure of the sweet-tasting protein thaumatin I at pH 8.0 reveals the large disulfide-rich region in domain II to be sensitive to a pH change

Energy Technology Data Exchange (ETDEWEB)

Masuda, Tetsuya, E-mail: t2masuda@kais.kyoto-u.ac.jp [Division of Food Science and Biotechnology, Graduate School of Agriculture, Kyoto University, Gokasho, Uji, Kyoto 611-0011 (Japan); Department of Natural Resources, Graduate School of Global Environmental Studies, Kyoto University, Gokasho, Uji, Kyoto 611-0011 (Japan); Ohta, Keisuke [Division of Food Science and Biotechnology, Graduate School of Agriculture, Kyoto University, Gokasho, Uji, Kyoto 611-0011 (Japan); Department of Natural Resources, Graduate School of Global Environmental Studies, Kyoto University, Gokasho, Uji, Kyoto 611-0011 (Japan); Mikami, Bunzo [Division of Applied Life Sciences, Graduate School of Agriculture, Kyoto University, Gokasho, Uji, Kyoto 611-0011 (Japan); Kitabatake, Naofumi [Department of Foods and Human Nutrition, Notre Dame Seishin University, Okayama 700-8516 (Japan); Tani, Fumito [Division of Food Science and Biotechnology, Graduate School of Agriculture, Kyoto University, Gokasho, Uji, Kyoto 611-0011 (Japan); Department of Natural Resources, Graduate School of Global Environmental Studies, Kyoto University, Gokasho, Uji, Kyoto 611-0011 (Japan)

2012-03-02

Highlights: Black-Right-Pointing-Pointer Structure of a recombinant thaumatin at pH 8.0 determined at a resolution of 1.0 A. Black-Right-Pointing-Pointer Substantial fluctuations of a loop in domain II was found in the structure at pH 8.0. Black-Right-Pointing-Pointer B-factors for Lys137, Lys163, and Lys187 were significantly affected by pH change. Black-Right-Pointing-Pointer An increase in mobility might play an important role in the heat-induced aggregation. -- Abstract: Thaumatin, an intensely sweet-tasting plant protein, elicits a sweet taste at 50 nM. Although the sweetness remains when thaumatin is heated at 80 Degree-Sign C for 4 h under acid conditions, it rapidly declines when heating at a pH above 6.5. To clarify the structural difference at high pH, the atomic structure of a recombinant thaumatin I at pH 8.0 was determined at a resolution of 1.0 A. Comparison to the crystal structure of thaumatin at pH 7.3 and 7.0 revealed the root-mean square deviation value of a C{alpha} atom to be substantially greater in the large disulfide-rich region of domain II, especially residues 154-164, suggesting that a loop region in domain II to be affected by solvent conditions. Furthermore, B-factors of Lys137, Lys163, and Lys187 were significantly affected by pH change, suggesting that a striking increase in the mobility of these lysine residues, which could facilitate a reaction with a free sulfhydryl residue produced via the {beta}-elimination of disulfide bonds by heating at a pH above 7.0. The increase in mobility of lysine residues as well as a loop region in domain II might play an important role in the heat-induced aggregation of thaumatin above pH 7.0.

Nanoscale insight of high piezoelectricity in high-TC PMN-PH-PT ceramics

Science.gov (United States)

Zhu, Rongfeng; Zhang, Qihui; Fang, Bijun; Zhang, Shuai; Zhao, Xiangyong; Ding, Jianning

2018-03-01

The piezoelectric properties of the high-Curie temperature (high-TC) 0.15Pb(Mg1/3Nb2/3)O3-0.38PbHfO3-0.47PbTiO3 (0.15PMN-0.38PH-0.47PT) ceramics prepared by three different methods were compared. The 0.15PMN-0.38PH-0.47PT ceramics synthesized by the partial oxalate route exhibit the optimum properties, in which d33* = 845.3 pm/V, d33 = 456.2 pC/N, Kp = 67.2%, and TC = 291 °C. The nanoscale origin of the high piezoelectric response of the 0.15PMN-0.38PH-0.47PT ceramics was investigated by piezoresponse force microscopy (PFM) using the ceramics synthesized by the partial oxalate route. Large quantities of fine stripe submicron ferroelectric domains are observed, which form large island domains. In order to give further insights into the piezoelectric properties of the 0.15PMN-0.38PH-0.47PT ceramics from a microscopic point of view, the local poling experiments and local switching spectroscopy piezoresponse force microscopy (SS-PFM) were investigated, from which the local converse piezoelectric coefficient d33*(l) is calculated as 220 pm/V.

Nanowire-templated microelectrodes for high-sensitivity pH detection

DEFF Research Database (Denmark)

Antohe, V.A.; Radu, Adrian; Mátéfi-Tempfli, Mária

2009-01-01

A highly sensitive pH capacitive sensor has been designed by confined growth of vertically aligned nanowire arrays on interdigited microelectrodes. The active surface of the device has been functionalized with an electrochemical pH transducer (polyaniline). We easily tune the device features...... by combining lithographic techniques with electrochemical synthesis. The reported electrical LC resonance measurements show considerable sensitivity enhancement compared to conventional capacitive pH sensors realized with microfabricated interdigited electrodes. The sensitivity can be easily improved...

Polyamine stress at high pH in Escherichia coli K-12

Directory of Open Access Journals (Sweden)

Tate Daniel P

2005-10-01

Full Text Available Abstract Background Polyamines such as spermine and spermidine are required for growth of Escherichia coli; they interact with nucleic acids, and they bind to ribosomes. Polyamines block porins and decrease membrane permeability, activities that may protect cells in acid. At high concentrations, however, polyamines impair growth. They impair growth more severely at high pH, probably due to their increased uptake as membrane-permeant weak bases. The role of pH is critical in understanding polyamine stress. Results The effect of polyamines was tested on survival of Escherichia coli K-12 W3110 in extreme acid or base (pH conditions outside the growth range. At pH 2, 10 mM spermine increased survival by 2-fold, and putrescine increased survival by 30%. At pH 9.8, however, E. coli survival was decreased 100-fold by 10 mM spermine, putrescine, cadaverine, or spermidine. At pH 8.5, spermine decreased the growth rate substantially, whereas little effect was seen at pH 5.5. Spermidine required ten-fold higher concentrations to impair growth. On proteomic 2-D gels, spermine and spermidine caused differential expression of 31 different proteins. During log-phase growth at pH 7.0, 1 mM spermine induced eight proteins, including PykF, GlpK, SerS, DeaD, OmpC and OmpF. Proteins repressed included acetate-inducible enzymes (YfiD, Pta, Lpd as well as RapA (HepA, and FabB. At pH 8.5, spermine induced additional proteins: TnaA, OmpA, YrdA and NanA (YhcJ and also repressed 17 proteins. Four of the proteins that spermine induced (GlpK, OmpA, OmpF, TnaA and five that were repressed (Lpd, Pta, SucB, TpiA, YfiD show similar induction or repression, respectively, in base compared to acid. Most of these base stress proteins were also regulated by spermidine, but only at ten-fold higher concentration (10 mM at high pH (pH 8.5. Conclusion Polyamines increase survival in extreme acid, but decrease E. coli survival in extreme base. Growth inhibition by spermine and

Real-time x-ray response of biocompatible solution gate AlGaN/GaN high electron mobility transistor devices

International Nuclear Information System (INIS)

Hofstetter, Markus; Funk, Maren; Paretzke, Herwig G.; Thalhammer, Stefan; Howgate, John; Sharp, Ian D.; Stutzmann, Martin

2010-01-01

We present the real-time x-ray irradiation response of charge and pH sensitive solution gate AlGaN/GaN high electron mobility transistors. The devices show stable and reproducible behavior under and following x-ray radiation, including a linear integrated response with dose into the μGy range. Titration measurements of devices in solution reveal that the linear pH response and sensitivity are not only retained under x-ray irradiation, but an irradiation response could also be measured. Since the devices are biocompatible, and can be simultaneously operated in aggressive fluids and under hard radiation, they are well-suited for both medical radiation dosimetry and biosensing applications.

Effects of pH and phosphate on metal distribution with emphasis on As speciation and mobilization in soils from a lead smelting site

International Nuclear Information System (INIS)

Impellitteri, Christopher A.

2005-01-01

Arsenic in soils from the Asarco lead smelter in East Helena, Montana was characterized by X-ray absorption spectroscopy (XAS). Arsenic oxidation state and geochemical speciation were analyzed as a function of depth (two sampling sites) and surface distribution. These results were compared with intensive desorption/dissolution experiments performed in a pH stat reactor for samples from the site with the highest degree of As heterogeneity. The objectives of the study were to investigate the solid-phase geochemical As speciation, assess the speciation of As in solutions equilibrated with the solids under controlled pH (pH=4 or 6) and Eh (using hydrogen or air) environments, observe the effects of phosphate on the release of As into solution, and examine the effects of phosphate on metal mobility in the systems. Arsenic was predominantly found in the As(V) valence state, though there was evidence that As(III) and As(0) were present also. The dominant geochemical phase was scorodite (FeAsO 4 .2H 2 O). The pH was controlled in the pH stat experiments by the addition of equinormal solutions of monoprotic (HNO 3 ), diprotic (H 2 SO 4 ), or triprotic (H 3 PO 4 ) acids. For many of the divalent metal cations, solution concentrations greatly decreased in the presence of phosphate. Solutions were also analyzed for anions. Evidence exists for sulfate release into solution. More As was released into solution at lower pH. A slight increase in solution arsenate occurs with the addition of phosphate, but the risk posed from the increased desorption/dissolution of As must be weighed against the decrease in solution concentrations of many metals especially Pb. If tailings from this site underwent acidification (e.g., acid mine drainage), in situ sequestration of metals by phosphate could be combined with placement of subsurface permeable reactive barriers for capture of As to reduce the risk associated with arsenic and trace metal mobilization. Results from this study could be used

High Thermoelectric Power Factor of High-Mobility 2D Electron Gas.

Science.gov (United States)

Ohta, Hiromichi; Kim, Sung Wng; Kaneki, Shota; Yamamoto, Atsushi; Hashizume, Tamotsu

2018-01-01

Thermoelectric conversion is an energy harvesting technology that directly converts waste heat from various sources into electricity by the Seebeck effect of thermoelectric materials with a large thermopower ( S ), high electrical conductivity (σ), and low thermal conductivity (κ). State-of-the-art nanostructuring techniques that significantly reduce κ have realized high-performance thermoelectric materials with a figure of merit ( ZT = S 2 ∙σ∙ T ∙κ -1 ) between 1.5 and 2. Although the power factor (PF = S 2 ∙σ) must also be enhanced to further improve ZT , the maximum PF remains near 1.5-4 mW m -1 K -2 due to the well-known trade-off relationship between S and σ. At a maximized PF, σ is much lower than the ideal value since impurity doping suppresses the carrier mobility. A metal-oxide-semiconductor high electron mobility transistor (MOS-HEMT) structure on an AlGaN/GaN heterostructure is prepared. Applying a gate electric field to the MOS-HEMT simultaneously modulates S and σ of the high-mobility electron gas from -490 µV K -1 and ≈10 -1 S cm -1 to -90 µV K -1 and ≈10 4 S cm -1 , while maintaining a high carrier mobility (≈1500 cm 2 V -1 s -1 ). The maximized PF of the high-mobility electron gas is ≈9 mW m -1 K -2 , which is a two- to sixfold increase compared to state-of-the-art practical thermoelectric materials.

Laboratory simulation studies of uranium mobility in natural waters

International Nuclear Information System (INIS)

Giblin, A.M.; Swaine, D.J.; Batts, B.D.

1981-01-01

The effects of imposed variations of pH and Eh on aqueous uranium mobility at 25 0 C have been studied in three simulations of natural water systems. Constituents tested for their effect on uranium mobility were: (a) hydrous ferric oxide, to represent adsorptive solids which precipitate or dissolve in response to variations in pH and Eh; (b) kaolinite, representing minerals which, although modified by pH and Eh changes, are present as solids over the pH-Eh range of natural waters; and (c) carbonate, to represent a strong uranium-complexing species. Uranium mobility measurements from each simulation were regressed against pH and Eh within a range appropriate to natural waters. Hydrous ferric oxide and kaolinite each affected uranium mobility, but in separate pH-Eh domains. Aqueous carbonate increased mobility of uranium, and adsorption of UO 2 (CO 3 ) 3 4- caused colloidal dispersion of hydrous ferric oxide, possibly explaining the presence of 'hydrothermal hematite' in some uranium deposits. Enhanced uranium mobility observed in the pH-Eh domains of thermodynamically insoluble uranium oxides could be explained if the oxides were present as colloids. Uranium persisting as a mobile species, even after reduction, has implications for the near surface genesis of uranium ores. (author)

Effects of pH and phosphate on metal distribution with emphasis on As speciation and mobilization in soils from a lead smelting site

Energy Technology Data Exchange (ETDEWEB)

Impellitteri, Christopher A. [United States Environmental Protection Agency, National Risk Management Research Laboratory, 26 West Martin Luther King Drive, Cincinnati, OH 45268 (United States)]. E-mail: Impellitteri.christopher@epa.gov

2005-06-01

Arsenic in soils from the Asarco lead smelter in East Helena, Montana was characterized by X-ray absorption spectroscopy (XAS). Arsenic oxidation state and geochemical speciation were analyzed as a function of depth (two sampling sites) and surface distribution. These results were compared with intensive desorption/dissolution experiments performed in a pH stat reactor for samples from the site with the highest degree of As heterogeneity. The objectives of the study were to investigate the solid-phase geochemical As speciation, assess the speciation of As in solutions equilibrated with the solids under controlled pH (pH=4 or 6) and Eh (using hydrogen or air) environments, observe the effects of phosphate on the release of As into solution, and examine the effects of phosphate on metal mobility in the systems. Arsenic was predominantly found in the As(V) valence state, though there was evidence that As(III) and As(0) were present also. The dominant geochemical phase was scorodite (FeAsO{sub 4}.2H{sub 2}O). The pH was controlled in the pH stat experiments by the addition of equinormal solutions of monoprotic (HNO{sub 3}), diprotic (H{sub 2}SO{sub 4}), or triprotic (H{sub 3}PO{sub 4}) acids. For many of the divalent metal cations, solution concentrations greatly decreased in the presence of phosphate. Solutions were also analyzed for anions. Evidence exists for sulfate release into solution. More As was released into solution at lower pH. A slight increase in solution arsenate occurs with the addition of phosphate, but the risk posed from the increased desorption/dissolution of As must be weighed against the decrease in solution concentrations of many metals especially Pb. If tailings from this site underwent acidification (e.g., acid mine drainage), in situ sequestration of metals by phosphate could be combined with placement of subsurface permeable reactive barriers for capture of As to reduce the risk associated with arsenic and trace metal mobilization. Results

Enacting the 'mobile' in tourism studies - Unraveling research practices

DEFF Research Database (Denmark)

Jensen, Martin Trandberg

This chapter showcases how mobile methods are more than calibrated techniques awaiting application by tourism researchers, but productive in the enactment of the mobile (Law and Urry, 2004). Drawing upon recent findings deriving from a PhD course on mobility and mobile methods it reveals the conc......This chapter showcases how mobile methods are more than calibrated techniques awaiting application by tourism researchers, but productive in the enactment of the mobile (Law and Urry, 2004). Drawing upon recent findings deriving from a PhD course on mobility and mobile methods it reveals......, the engagements with methods are acknowledged to be always political and contextual, reminding us to avoid essentialist discussions regarding research methods. Finally, the chapter draws on recent fieldwork to extend developments in mobilities-oriented tourism research, by employing auto-ethnography to call...

High-frequency hearing loss among mobile phone users.

Science.gov (United States)

Velayutham, P; Govindasamy, Gopala Krishnan; Raman, R; Prepageran, N; Ng, K H

2014-01-01

The objective of this study is to assess high frequency hearing (above 8 kHz) loss among prolonged mobile phone users is a tertiary Referral Center. Prospective single blinded study. This is the first study that used high-frequency audiometry. The wide usage of mobile phone is so profound that we were unable to find enough non-users as a control group. Therefore we compared the non-dominant ear to the dominant ear using audiometric measurements. The study was a blinded study wherein the audiologist did not know which was the dominant ear. A total of 100 subjects were studied. Of the subjects studied 53% were males and 47% females. Mean age was 27. The left ear was dominant in 63%, 22% were dominant in the right ear and 15% did not have a preference. This study showed that there is significant loss in the dominant ear compared to the non-dominant ear (P mobile phone revealed high frequency hearing loss in the dominant ear (mobile phone used) compared to the non dominant ear.

PhC-4 new high-speed camera with mirror scanning

International Nuclear Information System (INIS)

Daragan, A.O.; Belov, B.G.

1979-01-01

The description of the optical system and the construction of the high-speed PhC-4 photographic camera with mirror scanning of the continuously operating type is given. The optical system of the camera is based on the foursided rotating mirror, two optical inlets and two working sectors. The PhC-4 camera provides the framing rate up to 600 thousand frames per second. (author)

Application of zirconia membranes as high-temperature PH sensors

International Nuclear Information System (INIS)

Neidrach, L.W.

1983-01-01

The zirconia pH sensor behaves much like the classical glass electrode, but it extends the range of measurement to much higher temperatures - about 300 0 vs 120 0 C. It also has virtues over the glass electrode at lower temperatures because of the absence of an ''alkaline error.'' Like the glass electrode, it is insensitive to changes in the redox potential of the environment and, in turn, it exerts no influence on the environment. Such sensors have been finding application in the direct measurement of the pH of geothermal brines, of water in nuclear reactors, and in high-temperature corrosion studies. The sensors can also be used as ''pseudoreference'' electrodes for the measurement of redox and corrosion potentials in high-temperature media

Creating opportunities for science PhDs to pursue careers in high school education.

Science.gov (United States)

Doyle, Kari M H; Vale, Ronald D

2013-11-01

The United States is confronting important challenges at both the early and late stages of science education. At the level of K-12 education, a recent National Research Council report (Successful K-12 STEM Education) proposed a bold restructuring of how science is taught, moving away from memorizing facts and emphasizing hands-on, inquiry-based learning and a deeper understanding of the process of science. At higher levels of training, limited funding for science is leading PhDs to seek training and careers in areas other than research. Might science PhDs play a bigger role in the future of K-12 education, particularly at the high school level? We explore this question by discussing the roles that PhDs can play in high school education and the current and rather extensive barriers to PhDs entering the teaching profession and finally suggest ways to ease the entrance of qualified PhDs into high school education.

Creating opportunities for science PhDs to pursue careers in high school education

Science.gov (United States)

Doyle, Kari M. H.; Vale, Ronald D.

2013-01-01

The United States is confronting important challenges at both the early and late stages of science education. At the level of K–12 education, a recent National Research Council report (Successful K–12 STEM Education) proposed a bold restructuring of how science is taught, moving away from memorizing facts and emphasizing hands-on, inquiry-based learning and a deeper understanding of the process of science. At higher levels of training, limited funding for science is leading PhDs to seek training and careers in areas other than research. Might science PhDs play a bigger role in the future of K–12 education, particularly at the high school level? We explore this question by discussing the roles that PhDs can play in high school education and the current and rather extensive barriers to PhDs entering the teaching profession and finally suggest ways to ease the entrance of qualified PhDs into high school education. PMID:24174464

Micromagnetics on high-performance workstation and mobile computational platforms

Science.gov (United States)

Fu, S.; Chang, R.; Couture, S.; Menarini, M.; Escobar, M. A.; Kuteifan, M.; Lubarda, M.; Gabay, D.; Lomakin, V.

2015-05-01

The feasibility of using high-performance desktop and embedded mobile computational platforms is presented, including multi-core Intel central processing unit, Nvidia desktop graphics processing units, and Nvidia Jetson TK1 Platform. FastMag finite element method-based micromagnetic simulator is used as a testbed, showing high efficiency on all the platforms. Optimization aspects of improving the performance of the mobile systems are discussed. The high performance, low cost, low power consumption, and rapid performance increase of the embedded mobile systems make them a promising candidate for micromagnetic simulations. Such architectures can be used as standalone systems or can be built as low-power computing clusters.

High-frequency dynamics of ocean pH: a multi-ecosystem comparison.

Directory of Open Access Journals (Sweden)

Gretchen E Hofmann

Full Text Available The effect of Ocean Acidification (OA on marine biota is quasi-predictable at best. While perturbation studies, in the form of incubations under elevated pCO(2, reveal sensitivities and responses of individual species, one missing link in the OA story results from a chronic lack of pH data specific to a given species' natural habitat. Here, we present a compilation of continuous, high-resolution time series of upper ocean pH, collected using autonomous sensors, over a variety of ecosystems ranging from polar to tropical, open-ocean to coastal, kelp forest to coral reef. These observations reveal a continuum of month-long pH variability with standard deviations from 0.004 to 0.277 and ranges spanning 0.024 to 1.430 pH units. The nature of the observed variability was also highly site-dependent, with characteristic diel, semi-diurnal, and stochastic patterns of varying amplitudes. These biome-specific pH signatures disclose current levels of exposure to both high and low dissolved CO(2, often demonstrating that resident organisms are already experiencing pH regimes that are not predicted until 2100. Our data provide a first step toward crystallizing the biophysical link between environmental history of pH exposure and physiological resilience of marine organisms to fluctuations in seawater CO(2. Knowledge of this spatial and temporal variation in seawater chemistry allows us to improve the design of OA experiments: we can test organisms with a priori expectations of their tolerance guardrails, based on their natural range of exposure. Such hypothesis-testing will provide a deeper understanding of the effects of OA. Both intuitively simple to understand and powerfully informative, these and similar comparative time series can help guide management efforts to identify areas of marine habitat that can serve as refugia to acidification as well as areas that are particularly vulnerable to future ocean change.

High electron mobility in Ga(In)NAs films grown by molecular beam epitaxy

International Nuclear Information System (INIS)

Miyashita, Naoya; Ahsan, Nazmul; Monirul Islam, Muhammad; Okada, Yoshitaka; Inagaki, Makoto; Yamaguchi, Masafumi

2012-01-01

We report the highest mobility values above 2000 cm 2 /Vs in Si doped GaNAs film grown by molecular beam epitaxy. To understand the feature of the origin which limits the electron mobility in GaNAs, temperature dependences of mobility were measured for high mobility GaNAs and referential low mobility GaInNAs. Temperature dependent mobility for high mobility GaNAs is similar to the GaAs case, while that for low mobility GaInNAs shows large decrease in lower temperature region. The electron mobility of high quality GaNAs can be explained by intrinsic limiting factor of random alloy scattering and extrinsic factor of ionized impurity scattering.

Campylobacter, Salmonella, and Escherichia coli on broiler carcasses subjected to a high pH scald and low pH postpick chlorine dip.

Science.gov (United States)

Berrang, M E; Windham, W R; Meinersmann, R J

2011-04-01

The objective of this study was to determine the individual and combined effects of a high pH scald and a postpick chlorine dip on bacteria present on broiler carcasses. In each of 3 replications, a flock was sampled at several sites within a commercial broiler processing plant. Carcasses were sampled by whole carcass rinse before and after treated scalding at mean pH 9.89 or control scalding at mean pH 6.88. Other carcasses from the same flock run on both the treated and control scald lines were collected and sampled before and after a chlorine dip tank operated at mean total chlorine level of 83.3 mg/kg and pH 6.04. Rinses were cultured for numbers of Campylobacter and Escherichia coli and presence or absence of Salmonella. High pH scald was more effective than standard scald to lessen the prevalence and numbers of Campylobacter on broiler carcasses; a lower prevalence was maintained through the postpick chlorine dip tank. The pH of the scald tank made no difference in numbers of E. coli recovered from broiler carcasses at any tested point on the processing line. High pH scald was not more effective than standard scald to lessen Salmonella prevalence. Furthermore, it is unclear why the postpick chlorine dip effectively lessened Salmonella prevalence on only the control scald line. Although no evidence exists that these treatments have an additive effect when used in series, each treatment shows some promise individually. Further optimization may result in more effective decontamination of broiler carcasses.

Data dissemination in the wild: A testbed for high-mobility MANETs

DEFF Research Database (Denmark)

Vingelmann, Peter; Pedersen, Morten Videbæk; Heide, Janus

2012-01-01

This paper investigates the problem of efficient data dissemination in Mobile Ad hoc NETworks (MANETs) with high mobility. A testbed is presented; which provides a high degree of mobility in experiments. The testbed consists of 10 autonomous robots with mobile phones mounted on them. The mobile...... information, and the goal is to convey that information to all devices. A strategy is proposed that uses UDP broadcast transmissions and random linear network coding to facilitate the efficient exchange of information in the network. An application is introduced that implements this strategy on Nokia phones...

Metal Distribution and Mobility under alkaline conditions

International Nuclear Information System (INIS)

Dario, Maarten

2004-01-01

The adsorption of an element, expressed as its distribution between liquid (aquatic) and solid phases in the bio geosphere, largely determines its mobility and transport properties. This is of fundamental importance in the assessment of the performance of e.g. geologic repositories for hazardous elements like radionuclides. Geologic repositories for low and intermediate level nuclear waste will most likely be based on concrete constructions in a suitable bedrock, leading to a local chemical environment with pH well above 12. At this pH metal adsorption is very high, and thus the mobility is hindered. Organic complexing agents, such as natural humic matter from the ground and in the groundwater, as well as components in the waste (cleaning agents, degradation products from ion exchange resins and cellulose, cement additives etc.) would affect the sorption properties of the various elements in the waste. Trace element migration from a cementitious repository through the pH- and salinity gradient created around the repository would be affected by the presence and creation of particulate matter (colloids) that may serve as carriers that enhance the mobility. The objective of this thesis was to describe and quantify the sorption of some selected elements representative of spent nuclear fuel (Eu, Am) and other heavy metals (Zn, Cd, Hg) in a clay/cement environment (pH 10-13) and in the pH-gradient outside this environment. The potential of organic complexing agents and colloids to enhance metal migration was also investigated. It was shown that many organic ligands are able to reduce trace metal sorption under these conditions. It was not possible to calculate the effect of well-defined organic ligands on the metal sorption in a cement environment by using stability constants from the literature. A simple method for comparing the effect of different complexing agents on metal sorption is, however, suggested. The stability in terms of the particle size of suspended

Excess glycogen does not resolve high ultimate pH of oxidative muscle.

Science.gov (United States)

England, Eric M; Matarneh, Sulaiman K; Oliver, Emily M; Apaoblaza, Ariel; Scheffler, Tracy L; Shi, Hao; Gerrard, David E

2016-04-01

Skeletal muscle glycogen content can impact the extent of postmortem pH decline. Compared to glycolytic muscles, oxidative muscles contain lower glycogen levels antemortem which may contribute to the higher ultimate pH. In an effort to explore further the participation of glycogen in postmortem metabolism, we postulated that increasing the availability of glycogen would drive additional pH decline in oxidative muscles to equivalent pH values similar to the ultimate pH of glycolytic muscles. Glycolysis and pH declines were compared in porcine longissimus lumborum (glycolytic) and masseter (oxidative) muscles using an in vitro system in the presence of excess glycogen. The ultimate pH of the system containing longissimus lumborum reached a value similar to that observed in intact muscle. The pH decline of the system containing masseter samples stopped prematurely resulting in a higher ultimate pH which was similar to that of intact masseter muscle. To investigate further, we titrated powdered longissimus lumborum and masseter samples in the reaction buffer. As the percentage of glycolytic sample increased, the ultimate pH decreased. These data show that oxidative muscle produces meat with a high ultimate pH regardless of glycogen content and suggest that inherent muscle factors associated with glycolytic muscle control the extent of pH decline in pig muscles. Copyright © 2015 Elsevier Ltd. All rights reserved.

Measurement of the Extracellular pH of Adherently Growing Mammalian Cells with High Spatial Resolution Using a Voltammetric pH Microsensor.

Science.gov (United States)

Munteanu, Raluca-Elena; Stǎnicǎ, Luciana; Gheorghiu, Mihaela; Gáspár, Szilveszter

2018-05-15

There are only a few tools suitable for measuring the extracellular pH of adherently growing mammalian cells with high spatial resolution, and none of them is widely used in laboratories around the world. Cell biologists very often limit themselves to measuring the intracellular pH with commercially available fluorescent probes. Therefore, we built a voltammetric pH microsensor and investigated its suitability for monitoring the extracellular pH of adherently growing mammalian cells. The voltammetric pH microsensor consisted of a 37 μm diameter carbon fiber microelectrode modified with reduced graphene oxide and syringaldazine. While graphene oxide was used to increase the electrochemically active surface area of our sensor, syringaldazine facilitated pH sensing through its pH-dependent electrochemical oxidation and reduction. The good sensitivity (60 ± 2.5 mV/pH unit), reproducibility (coefficient of variation ≤3% for the same pH measured with 5 different microsensors), and stability (pH drift around 0.05 units in 3 h) of the built voltammetric pH sensors were successfully used to investigate the acidification of the extracellular space of both cancer cells and normal cells. The results indicate that the developed pH microsensor and the perfected experimental protocol based on scanning electrochemical microscopy can reveal details of the pH regulation of cells not attainable with pH sensors lacking spatial resolution or which cannot be reproducibly positioned in the extracellular space.

High performance flexible pH sensor based on carboxyl-functionalized and DEP aligned SWNTs

International Nuclear Information System (INIS)

Liu, Lu; Shao, Jinyou; Li, Xiangming; Zhao, Qiang; Nie, Bangbang; Xu, Chuan; Ding, Haitao

2016-01-01

Highlights: • The flexible chemiresistive pH sensor based on two-terminal microsensors eliminating the need for a reference electrode, is simple in structure and can be fabricated on a variety of substrates such as PET, PI and PVC. • SWNTs as an ideal one dimensional material are carboxyl-functionalized to make the pH sensor show high sensitivity and outstanding flexibility for practical applications. • DEP technique is used to manipulate and position SWNTs into appropriate locations and desired formations to improve the metal-nanotube interface and highly rapid detection of pH value, resulting in better overall device performance. • Mechanical bendability of the pH sensor, which arises from the combination of flexible PET substrates and SWNTs, offer a significant improvement for applications that are difficult or impossible to achieve with traditional sensors on rigid substrates. - Abstract: The detection and control of the pH is very important in many biomedical and chemical reaction processes. A miniaturized flexible pH sensor that is light weight, robust, and conformable is very important in many applications, such as multifunctional lab-on-a-chip systems or wearable biomedical devices. In this work, we demonstrate a flexible chemiresistive pH sensor based on dielectrophoresis (DEP) aligned carboxyl-functionalized single-walled carbon nanotubes (SWNTs). Decorated carboxyl groups can react with hydrogen (H"+) and hydroxide (OH"−) ions, enabling the sensor to be capable of sensing the pH. DEP is used to deposit well-organized and highly aligned SWNTs in desired locations, which improves the metal-nanotube interface and highly rapid detection of the pH, resulting in better overall device performance. When pH buffer solutions are dropped onto such SWNTs, the H"+ and OH"− ions caninteract with the carboxyl groups and affect the generation of holes and electrons in the SWNTs, leading to resistance variations in the SWNTs. The results shows that the

High performance flexible pH sensor based on carboxyl-functionalized and DEP aligned SWNTs

Energy Technology Data Exchange (ETDEWEB)

Liu, Lu; Shao, Jinyou, E-mail: jyshao@mail.xjtu.edu.cn; Li, Xiangming; Zhao, Qiang; Nie, Bangbang; Xu, Chuan; Ding, Haitao

2016-11-15

Highlights: • The flexible chemiresistive pH sensor based on two-terminal microsensors eliminating the need for a reference electrode, is simple in structure and can be fabricated on a variety of substrates such as PET, PI and PVC. • SWNTs as an ideal one dimensional material are carboxyl-functionalized to make the pH sensor show high sensitivity and outstanding flexibility for practical applications. • DEP technique is used to manipulate and position SWNTs into appropriate locations and desired formations to improve the metal-nanotube interface and highly rapid detection of pH value, resulting in better overall device performance. • Mechanical bendability of the pH sensor, which arises from the combination of flexible PET substrates and SWNTs, offer a significant improvement for applications that are difficult or impossible to achieve with traditional sensors on rigid substrates. - Abstract: The detection and control of the pH is very important in many biomedical and chemical reaction processes. A miniaturized flexible pH sensor that is light weight, robust, and conformable is very important in many applications, such as multifunctional lab-on-a-chip systems or wearable biomedical devices. In this work, we demonstrate a flexible chemiresistive pH sensor based on dielectrophoresis (DEP) aligned carboxyl-functionalized single-walled carbon nanotubes (SWNTs). Decorated carboxyl groups can react with hydrogen (H{sup +}) and hydroxide (OH{sup −}) ions, enabling the sensor to be capable of sensing the pH. DEP is used to deposit well-organized and highly aligned SWNTs in desired locations, which improves the metal-nanotube interface and highly rapid detection of the pH, resulting in better overall device performance. When pH buffer solutions are dropped onto such SWNTs, the H{sup +} and OH{sup −} ions caninteract with the carboxyl groups and affect the generation of holes and electrons in the SWNTs, leading to resistance variations in the SWNTs. The results

Prediction of the chromatographic retention of acid-base compounds in pH buffered methanol-water mobile phases in gradient mode by a simplified model.

Science.gov (United States)

Andrés, Axel; Rosés, Martí; Bosch, Elisabeth

2015-03-13

Retention of ionizable analytes under gradient elution depends on the pH of the mobile phase, the pKa of the analyte and their evolution along the programmed gradient. In previous work, a model depending on two fitting parameters was recommended because of its very favorable relationship between accuracy and required experimental work. It was developed using acetonitrile as the organic modifier and involves pKa modeling by means of equations that take into account the acidic functional group of the compound (carboxylic acid, protonated amine, etc.). In this work, the two-parameter predicting model is tested and validated using methanol as the organic modifier of the mobile phase and several compounds of higher pharmaceutical relevance and structural complexity as testing analytes. The results have been quite good overall, showing that the predicting model is applicable to a wide variety of acid-base compounds using mobile phases prepared with acetonitrile or methanol. Copyright © 2015 Elsevier B.V. All rights reserved.

Making Everyday Mobility

DEFF Research Database (Denmark)

Wind, Simon

2013; Urry 2007) and family theory (Holdsworth 2013; Morgan 2011), it is argued that family mobility is far from only an instrumental phenomenon, displacing family members back and forth between activities and doings, but also a type of family practice (Morgan, 2011) carrying social and emotional...... coping process in the family, it is argued that making and performing mobility practices is to be understood as creating elasticity. Following this, it is elasticity that enables family members to stretch to accommodate the family’s practical, social and emotional conditions as well as adapt......Based upon a qualitative PhD study of 11 families everyday mobility, this paper inquiries into the everyday mobility of families with children in the Greater Copenhagen Area and the role mobility plays in contributing to coping in the families’ everyday life. Drawing on Mobilities theory (Jensen...

Hierarchical micro-mobility management in high-speed multihop access networks

Institute of Scientific and Technical Information of China (English)

TANG Bi-hua; MA Xiao-lei; LIU Yuan-an; GAO Jin-chun

2006-01-01

This article integrates the hierarchical micro-mobility management and the high-speed multihop access networks (HMAN), to accomplish the smooth handover between different access routers. The proposed soft handover scheme in the high-speed HMAN can solve the micro-mobility management problem in the access network. This article also proposes the hybrid access router (AR) advertisement scheme and AR selection algorithm, which uses the time delay and stable route to the AR as the gateway selection parameters. By simulation, the proposed micro-mobility management scheme can achieve high packet delivery fraction and improve the lifetime of network.

Mobile marketing for mobile games

OpenAIRE

Vu, Giang

2016-01-01

Highly developed mobile technology and devices enable the rise of mobile game industry and mobile marketing. Hence mobile marketing for mobile game is an essential key for a mobile game success. Even though there are many articles on marketing for mobile games, there is a need of highly understanding mobile marketing strategies, how to launch a mobile campaign for a mobile game. Besides that, it is essential to understand the relationship between mobile advertising and users behaviours. There...

[Influences of the mobile phase constitution, salt concentration and pH value on retention characters of proteins on the metal chelate column].

Science.gov (United States)

Li, R; Di, Z M; Chen, G L

2001-09-01

The effects of the nature and concentration of salts, pH value and competitive eluent in the mobile phase on the protein retention have been systematically investigated. A mathematical expression describing the protein retention in metal chelate chromatography has been derived. It is proposed that the eluting power of the salt solution can be expressed by the eluent strength exponent epsilon. According to the retention characters of protein under different chromatographic conditions, the interaction between the various metal chelate ligands and proteins is discussed. The protein retention on the metal chelate column is a cooperative interactions of coordination, electrostatic and hydrophobic interaction. For the strong combined metal column with proteins such as IDA-Cu, the coordination is the most important, and the electrostatic interaction is secondary in chromatographic process. However, for the weak combined metal columns with proteins such as IDA-Ni, IDA-Co and IDA-Zn, the electrostatic interaction between the metal chelate ligands and proteins is the chief one, while the coordination is the next in importance. When the mobile phase contains high concentration of salt which can't form complex with the immobilized metal, the hydrophobic interaction between the protein and stationary phase will be increased. As the interaction between the metal chelate ligand and proteins relates to chromatographic operating conditions closely, different elution processes may be selected for different metal chelate columns. The gradient elution is generally performed by the low concentration of salt or different pH for weakly combined columns with proteins, however the competitive elution procedure is commonly utilized for strongly combined column. The experiment showed that NH3 is an excellent competitive eluent. It isn't only give the efficient separation of proteins, but also has the advantages of cheapness, less bleeding of the immobilized metals and ease of controlling NH3

Isolation and cultivation of microalgae select for low growth rate and tolerance to high pH

DEFF Research Database (Denmark)

Berge, Terje; Daugbjerg, Niels; Hansen, Per Juel

2012-01-01

Harmful microalgal blooms or red tides are often associated with high levels of pH. Similarly, species and strains of microalgae cultivated in the laboratory with enriched media experience recurrent events of high pH between dilutions with fresh medium. To study the potential for laboratory...... of upper pH tolerance limits were higher in the younger (20 years). These results suggest selection of strains best adapted to tolerate or postpone/avoid events of high pH in the laboratory. Our data have implications for experimental studies of pH response and reaction norms in general of microalgae...

Engaging with mobile methods

DEFF Research Database (Denmark)

Jensen, Martin Trandberg

2014-01-01

This chapter showcases how mobile methods are more than calibrated techniques awaiting application by tourism researchers, but productive in the enactment of the mobile (Law and Urry, 2004). Drawing upon recent findings deriving from a PhD course on mobility and mobile methods it reveals...... the conceptual ambiguousness of the term ‘mobile methods’. In order to explore this ambiguousness the chapter provides a number of examples deriving from tourism research, to explore how mobile methods are always entangled in ideologies, predispositions, conventions and practice-realities. Accordingly......, the engagements with methods are acknowledged to be always political and contextual, reminding us to avoid essentialist discussions regarding research methods. Finally, the chapter draws on recent fieldwork to extend developments in mobilities-oriented tourism research, by employing auto-ethnography to call...

Designing for mobile interaction

DEFF Research Database (Denmark)

Nazzi, Elena

2009-01-01

The theme of this PhD project is designing for mobile interaction with devices and services, for the accessing, making, and sharing of information, taking into account the dynamic physical and social settings that embrace this interaction. To narrow down this theme, the whole project focuses...... on the exploitation of social interaction --- in particular among senior citizens --- to enhance and support mobile interaction....

Effects of sodium hypochlorite and high pH buffer solution in electrokinetic soil treatment on soil chromium removal and the functional diversity of soil microbial community

International Nuclear Information System (INIS)

Cang Long; Zhou Dongmei; Alshawabkeh, Akram N.; Chen Haifeng

2007-01-01

Effects of sodium hypochlorite (NaClO), applied as an oxidant in catholyte, and high pH buffer solution on soil Cr removal and the functional diversity of soil microbial community during enhanced electrokinetic treatments of a chromium (Cr) contaminated red soil are evaluated. Using pH control system to maintain high alkalinity of soil together with the use of NaClO increased the electrical conductivities of soil pore liquid and electroosmotic flux compared with the control (Exp-01). The pH control and NaClO improved the removal of Cr(VI) and total Cr from the soil. The highest removal percentages of soil Cr(VI) and total Cr were 96 and 72%, respectively, in Exp-04 when the pH value of the anolyte was controlled at 10 and NaClO was added in the catholyte. The alkaline soil environment and introduction of NaClO in the soil enhanced the desorption of Cr(VI) from the soil and promoted Cr(III) oxidation to mobile Cr(VI), respectively. However, the elevated pH and introduction of NaClO in the soil, which are necessary for improving the removal efficiency of soil Cr, resulted in a significantly adverse impact on the functional diversity of soil microbial community. It suggests that to assess the negative impact of extreme conditions for enhancing the extraction efficiencies of Cr on the soil properties and function is necessary

High school students’ usage behavior and views about mobile phones

Directory of Open Access Journals (Sweden)

Ahmet Ergin

2014-09-01

Full Text Available Objective: The aim of this study was to determine high school students’ usage behavior and views about mobile phones. Methods:Totally 253 (85.5% students educated at Honaz High School within the academic year 2010-2011, participated to this cross-sectional study and a questionnaire consisting of 42 questions which aimed to determine usage behavior and views about mobile phones was administered to the students. Results:The mean age of the students was 16.1 ± 1.1 years, and 56.9% of them were girl. 79.8% of students have mobile phone and 53.9% of them make daily average of over 30 minutes mobile phone calls. 76.1% of participants stated that they did not use headphones, 78.1% did not turn off their mobile phones when they are sleeping and 67.3% put it right next to them or under the pillow. 83.1% of students think mobile phones are harmful for human health, 56.7% think the base stations are harmful to human health and the environment, 91.3% think mobile phones are harmful for children, pregnant women and elderly people. Conclusion: It is found that students’ mobile phone ownership is widespread, the age of starting to use mobile phone and headphones usage is low, knowledge about the base stations is not adequate.

Unravelling the effects of mobile phase additives in supercritical fluid chromatography. Part I: Polarity and acidity of the mobile phase.

Science.gov (United States)

West, Caroline; Melin, Jodie; Ansouri, Hassna; Mengue Metogo, Maïly

2017-04-07

The mobile phases employed in current supercritical fluid chromatography (SFC) are usually composed of a mixture of pressurized carbon dioxide and a co-solvent. The co-solvent is most often an alcohol and may contain a third component in small proportions, called an additive (acid, base or salt). The polarity of such mobile phase compositions is here re-evaluated with a solvatochromic dye (Nile Red), particularly to assess the contribution of additives. It appears that additives, when employed in usual concentration range (0.1% or 20mM) do not modify the polarity in the immediate environment of the probe. In addition, the combination of carbon dioxide and an alcohol is known to form alkoxylcarbonic acid, supposedly conferring some acidic character to SFC mobile phases. Direct measurements of the apparent pH are impossible, but colour indicators of pH can be used to define the range of apparent pH provided by carbon dioxide-alcohol mixtures, with or without additives. Five colour indicators (Thymol Blue, Bromocresol Green, Methyl Red, Bromocresol Purple, and Bromothymol Blue) were selected to provide a wide range of aqueous pK a values (from 1.7 to 8.9). UV-vis absorption spectra measured in liquid phases of controlled pH were compared to those measured with a diode-array detector employed in SFC, with the help of chemometric methods. Based on these observations, it is concluded that the apparent pH range in carbon dioxide-methanol mobile phases is close to 5. Increasing the proportion of methanol (in the course of a gradient elution for instance) causes decreasing apparent pH. Strong acids can further decrease the apparent pH below 1.7; strong bases have little influence on the apparent pH, probably because, in this range of concentrations, they are titrated by alkoxylcarbonic acid or form ion pairs with alkoxycarbonate. However, bases and salts could stabilize the acidity in the course of gradient runs. Copyright © 2017 Elsevier B.V. All rights reserved.

Interface-controlled, high-mobility organic transistors

NARCIS (Netherlands)

Jurchescu, Oana D.; Popinciuc, Mihaita; van Wees, Bart J.; Palstra, Thomas T. M.

2007-01-01

The achievement of high mobilities in field-effect transistors (FETs) is one of the main challenges for the widespread application of organic conductors in devices. Good device performance of a single-crystal pentacene FET requires both removal of impurity molecules from the bulk and the

Design research into mobile museum mediation

DEFF Research Database (Denmark)

Baggesen, Rikke Haller

2013-01-01

community. 
The PhD research project “Mobile Mediation of Fashion by Museums” explores how aesthetic and ethnographic design methods can be used to develop mobile experiences and articulate museological matters of concern. Building on user perspectives, expressed in response to cultural probes, the project...

High Ph, Ammonia Toxicity, and the Search for Life on the Jovian Planets

Science.gov (United States)

Deal, P. H.; Souza, K. A.; Mack, H. M.

1975-01-01

The effects of pH and ammonia concentration were studied separately, where possible, on a variety of organisms, including some isolated from natural environments of high pH and/or ammonia concentration. Escherichia coli and Bacillus subtilis are both extremely sensitive to ammonia. An aerobic organism (growth up to pH 11.4) from an alkaline spring is more resistant, but exhibits a toxic response to ammonia at a pH much lower than its maximum for growth. The greatest ammonia resistance has been found in an unidentified organism growing at near neutral pH. Even in this case, however, urvival at ammonia concentrations reasonably expected on the Jovian planets is measured in hours. This is two to three orders of magnitude longer than for E. coli. Results support the tentative conclusion that contamination of the Jovian planets with terrestrial organisms that can grow is unlikely. However, the range of toxic response noted, coupled with the observation that terrestrial life has not been exposed to high ammonia concentrations for millions of years, suggests that adaptation to greater ammonia tolerance may be possible.

Optical fiber pH sensors for high temperature water. Final report

International Nuclear Information System (INIS)

McCrae, D.; Saaski, E.

1994-11-01

The goal of this program was the development of an optical pH measurement system capable of operating in a high-temperature aqueous environment. This project built upon a dual-wavelength fiber optic sensing system previously developed by Research International which utilizes light-emitting diodes as light sources and provides remote absorption spectroscopy via a single bidirectional optical fiber. Suitable materials for constructing an optical pH sensing element were identified during the program. These included a sapphire/Ti/Pt/Au thin-film reflector, quartz and sapphire waveguides, a poly(benzimidazole) matrix, and an azo chromophore indicator. By a suitable combination of these design elements, it appears possible to optically measure pH in aqueous systems up to a temperature of about 150 degrees C. A pH sensing system capable of operating in high-purity, low-conductivity water was built using quasi-evanescent wave sensing techniques. The sensing element incorporated a novel, mixed cellulose/cellulose acetate waveguide to which an azo indicator was bound. Testing revealed that the system could reproducibly respond to pH changes arising from 1 ppm differences in the morpholine content of low-conductivity water without influencing the measurement. The sensing system was stable for 150 hrs at room temperature, and no loss or degradation of the pH-responsive optical indicator was seen in 160 hrs at 50 degrees C. However, the prototype polymer waveguide lost transparency at 1.7% per day during this same 50 degrees C test. Additional effort is warranted in the areas of water-compatible waveguides and evanescent-wave detection methods

No-core fiber-based highly sensitive optical fiber pH sensor.

Science.gov (United States)

Bhardwaj, Vanita; Pathak, Akhilesh Kumar; Singh, Vinod Kumar

2017-05-01

The present work describes the fabrication and characterization of an optical fiber pH sensor using a sol–gel technique. The sensing head configuration is incorporated using a short section of no-core fiber, coated with tetraethyl orthosilicate and spliced at the end of a single mode fiber with a bulge. Different types of indicators (bromophenol blue, cresol red, and chlorophenol red) were used to achieve a wide pH range from 2 to 13. High sensitivities of the fabricated device were found to be 1.02 and ? 0.93 ?? nm / pH for acidic and alkaline solutions, respectively. From the characterization results, it was noted that there is an impact of ionic strength and an effect of the temperature of liquid on the response characteristic, which is an advantage of the existing device over the other pH sensors. The fabricated sensor exhibited good reflection spectrum, indicating a blueshift in resonance wavelength for alkaline solutions and a redshift for acidic solutions.

Influence of pH of spray solution on optoelectronic properties of cadmium oxide thin films

International Nuclear Information System (INIS)

Hodlur, R. M.; Rabinal, M. K.

2015-01-01

Highly conducting transparent cadmium oxide thin films were prepared by the conventional spray pyrolysis technique. The pH of the spray solution is varied by adding ammonia/hydrochloric acid. The effect of pH on the morphology, crystallinity and optoelectronic properties of these films is studied. The structural analysis showed all the films in the cubic phase. For the films with pH < 7 (acidic condition), the preferred orientation is along the (111) direction and for those with pH >7 (alkaline condition), the preferred orientation is along the (200) direction. A lowest resistivity of 9.9 × 10 −4 Ω·cm (with carrier concentration = 5.1 × 10 20 cm −3 , mobility = 12.4 cm 2 /(V·s)) is observed for pH ≈ 12. The resistivity is tuned almost by three orders of magnitude by controlling the bath pH with optical transmittance more than 70%. Thus, the electrical conductivity of CdO films could be easily tuned by simply varying the pH of the spray solution without compromising the optical transparency. (paper)

Temperature dependence of ballistic mobility in a metamorphic InGaAs/InAlAs high electron mobility transistor

International Nuclear Information System (INIS)

Lee, Jongkyong; Gang, Suhyun; Jo, Yongcheol; Kim, Jongmin; Woo, Hyeonseok; Han, Jaeseok; Kim, Hyungsang; Im, Hyunsik

2014-01-01

We have investigated the temperature dependence of ballistic mobility in a 100 nm-long InGaAs/InAlAs metamorphic high-electron-mobility transistor designed for millimeter-wavelength RF applications. To extract the temperature dependence of quasi-ballistic mobility, our experiment involves measurements of the effective mobility in the low-bias linear region of the transistor and of the collision-dominated Hall mobility using a gated Hall bar of the same epitaxial structure. The data measured from the experiment are consistent with that of modeled ballistic mobility based on ballistic transport theory. These results advance the understanding of ballistic transport in various transistors with a nano-scale channel length that is comparable to the carrier's mean free path in the channel.

Effects of high medium pH on growth, metabolism and transport in Saccharomyces cerevisiae.

Science.gov (United States)

Peña, Antonio; Sánchez, Norma Silvia; Álvarez, Helber; Calahorra, Martha; Ramírez, Jorge

2015-03-01

Growth of Saccharomyces cerevisiae stopped by maintaining the pH of the medium in a pH-stat at pH 8.0 or 9.0. Studying its main physiological capacities and comparing cells after incubation at pH 6.0 vs. 8.0 or 9.0, we found that (a) fermentation was moderately decreased by high pH and respiration was similar and sensitive to the addition of an uncoupler, (b) ATP and glucose-6-phosphate levels upon glucose addition increased to similar levels and (c) proton pumping and K(+) transport were also not affected; all this indicating that energy mechanisms were preserved. Growth inhibition at high pH was also not due to a significant lower amino acid transport by the cells or incorporation into proteins. The cell cycle stopped at pH 9.0, probably due to an arrest as a result of adjustments needed by the cells to contend with the changes under these conditions, and microarray experiments showed some relevant changes to this response. © FEMS 2015. All rights reserved. For permissions, please e-mail: journals.permission@oup.com.

Ultra high hole mobilities in a pure strained Ge quantum well

International Nuclear Information System (INIS)

Mironov, O.A.; Hassan, A.H.A.; Morris, R.J.H.; Dobbie, A.; Uhlarz, M.; Chrastina, D.; Hague, J.P.; Kiatgamolchai, S.; Beanland, R.; Gabani, S.; Berkutov, I.B.; Helm, M.; Drachenko, O.; Myronov, M.; Leadley, D.R.

2014-01-01

Hole mobilities at low and room temperature (RT) have been studied for a strained sGe/SiGe heterostructure using standard Van der Pauw resistivity and Hall effect measurements. The range of magnetic field and temperatures used were − 14 T < B < + 14 T and 1.5 K < T < 300 K respectively. Using maximum entropy-mobility spectrum analysis (ME-MSA) and Bryan's algorithm mobility spectrum (BAMS) analysis, a RT two dimensional hole gas drift mobility of (3.9 ± 0.4) × 10 3 cm 2 /V s was determined for a sheet density (p s ) 9.8 × 10 10 cm −2 (by ME-MSA) and (3.9 ± 0.2) × 10 3 cm 2 /V s for a sheet density (p s ) 5.9 × 10 10 cm −2 (by BAMS). - Highlights: • Pure strained Ge channel grown by reduced pressure chemical vapor deposition • Maximum entropy-mobility spectrum analysis • Bryan's algorithm mobility spectrum analysis • High room temperature hole drift mobility of (3.9 ± 0.4) × 10 3 cm 2 /V s • Extremely high hole mobility of 1.1 × 10 6 cm 2 /V s at 12 K

High mobility transparent conducting oxides for thin film solar cells

International Nuclear Information System (INIS)

Calnan, S.; Tiwari, A.N.

2010-01-01

A special class of transparent conducting oxides (TCO) with high mobility of > 65 cm 2 V -1 s -1 allows film resistivity in the low 10 -4 Ω cm range and a high transparency of > 80% over a wide spectrum, from 300 nm to beyond 1500 nm. This exceptional coincidence of desirable optical and electrical properties provides opportunities to improve the performance of opto-electronic devices and opens possibilities for new applications. Strategies to attain high mobility (HM) TCO materials as well as the current status of such materials based on indium and cadmium containing oxides are presented. Various concepts used to understand the underlying mechanisms for high mobility in HMTCO films are discussed. Examples of HMTCO layers used as transparent electrodes in thin film solar cells are used to illustrate possible improvements in solar cell performance. Finally, challenges and prospects for further development of HMTCO materials are discussed.

Highly Sensitive and Wide-Dynamic-Range Multichannel Optical-Fiber pH Sensor Based on PWM Technique

OpenAIRE

Md. Rajibur Rahaman Khan; Shin-Won Kang

2016-01-01

In this study, we propose a highly sensitive multichannel pH sensor that is based on an optical-fiber pulse width modulation (PWM) technique. According to the optical-fiber PWM method, the received sensing signal?s pulse width changes when the optical-fiber pH sensing-element of the array comes into contact with pH buffer solutions. The proposed optical-fiber PWM pH-sensing system offers a linear sensing response over a wide range of pH values from 2 to 12, with a high pH-sensing ability. The...

High mobility solution-processed hybrid light emitting transistors

International Nuclear Information System (INIS)

Walker, Bright; Kim, Jin Young; Ullah, Mujeeb; Burn, Paul L.; Namdas, Ebinazar B.; Chae, Gil Jo; Cho, Shinuk; Seo, Jung Hwa

2014-01-01

We report the design, fabrication, and characterization of high-performance, solution-processed hybrid (inorganic-organic) light emitting transistors (HLETs). The devices employ a high-mobility, solution-processed cadmium sulfide layer as the switching and transport layer, with a conjugated polymer Super Yellow as an emissive material in non-planar source/drain transistor geometry. We demonstrate HLETs with electron mobilities of up to 19.5 cm 2 /V s, current on/off ratios of >10 7 , and external quantum efficiency of 10 −2 % at 2100 cd/m 2 . These combined optical and electrical performance exceed those reported to date for HLETs. Furthermore, we provide full analysis of charge injection, charge transport, and recombination mechanism of the HLETs. The high brightness coupled with a high on/off ratio and low-cost solution processing makes this type of hybrid device attractive from a manufacturing perspective

Interaction of a non-histone chromatin protein (high-mobility group protein 2) with DNA

International Nuclear Information System (INIS)

Goodwin, G.H.; Shooter, K.V.; Johns, E.W.

1975-01-01

The interaction with DNA of the calf thymus chromatin non-histone protein termed the high-mobility group protein 2 has been studied by sedimentation analysis in the ultracentrifuge and by measuring the binding of the 125 I-labelled protein to DNA. The results have been compared with those obtained previously by us [Eur. J. Biochem. (1974) 47, 263-270] for the interaction of high-mobility group protein 1 with DNA. Although the binding parameters are similar for these two proteins, high-mobility group protein 2 differs from high-mobility group protein 1 in that the former appears to change the shape of the DNA to a more compact form. The molecular weight of high-mobility group protein 2 has been determined by equilibrium sedimentation and a mean value of 26,000 was obtained. A low level of nuclease activity detected in one preparation of high-mobility group protein 2 has been investigated. (orig.) [de

High yielding mutants of blackgram variety 'PH-25'

International Nuclear Information System (INIS)

Misra, R.C.; Mohapatra, B.D.; Panda, B.S.

2001-01-01

Seeds of blackgram (Vigna mungo L.) variety 'PH-5' were treated with chemical mutagens ethyl methanesulfonate (EMS), nitrosoguanidine (NG), maleic hydrazide (MH) and sodium azide (NaN 3 ), each at 3 different concentrations. Thirty six mutant lines developed from mutagenic treatments along with parent varieties were tested in M 4 generation. The mutants showed wide variation in most of the traits and multivariante D 2 analysis showed genetic divergence among themselves. Twenty of the thirty mutants showed genetic divergence from parent. Ten selected high yielding mutants were tested in M 5 . Yield and other productive traits of five high yielding mutants in M 4 and M 5 are presented

Lessons learnt from teachers' perspectives on mobile learning in ...

African Journals Online (AJOL)

Dumisani Jantjies

2016-08-18

Aug 18, 2016 ... multilingual mobile learning technology to support teaching and learning ..... study done, we had to submit an ethics application ..... mobile learning: A South African perspective. PhD thesis. England, UK: University of Warwick.

Highly Mobile Students: Educational Problems and Possible Solutions. ERIC/CUE Digest, Number 73.

Science.gov (United States)

ERIC Clearinghouse on Urban Education, New York, NY.

The following two types of student mobility stand out as causing educational problems: (1) inner-city mobility, which is prompted largely by fluctuations in the job market; and (2) intra-city mobility, which is caused by upward mobility or by poverty and homelessness. Most research indicates that high mobility negatively affects student…

BEYOND THE WORK-LIFE BALANCE: FAMILY AND INTERNATIONAL MOBILITY OF THE HIGHLY SKILLED

Directory of Open Access Journals (Sweden)

Núria Vergés Bosch

2013-10-01

Full Text Available International mobility of the highly skilled has become one of the cornerstones of development in the current knowledge society. Correspondingly, highly skilled personnel are impelled to move abroad in order to improve their competences and build influential professional networks. Mobility implies some advantages involving personal, social and family opportunities when movers experience handicaps in their country of origin. For movers, mobility becomes a new challenge beyond the work-family balance, particularly for women who usually take on the lion’s share of childcare and domestic tasks within the family. The literature exploring the gender dimension in relation to international mobility points to complex outcomes. Firstly, women are taking on a more active role in international mobility processes, even when they have family. Secondly, family and international mobility are interrelated both for men and for women, although family could become a hindrance, particularly for women. Thirdly, international mobility and women’s career development may interfere with family formation or modify traditional family values. Finally, families moving abroad constitute a challenge for public policy, since they present a new area of problems. We aim to analyse the relationship between international mobility and family based on in-depth interviews from a purposive sample of highly skilled personnel in science and technology. The results of our research suggest that international mobility of the highly skilled has effects on the family and vice versa; however, while international mobility and family are compatible, measures and policies to reconcile them are still insufficient.

An Architecture Offering Mobile Pollution Sensing with High Spatial Resolution

Directory of Open Access Journals (Sweden)

Oscar Alvear

2016-01-01

Full Text Available Mobile sensing is becoming the best option to monitor our environment due to its ease of use, high flexibility, and low price. In this paper, we present a mobile sensing architecture able to monitor different pollutants using low-end sensors. Although the proposed solution can be deployed everywhere, it becomes especially meaningful in crowded cities where pollution values are often high, being of great concern to both population and authorities. Our architecture is composed of three different modules: a mobile sensor for monitoring environment pollutants, an Android-based device for transferring the gathered data to a central server, and a central processing server for analyzing the pollution distribution. Moreover, we analyze different issues related to the monitoring process: (i filtering captured data to reduce the variability of consecutive measurements; (ii converting the sensor output to actual pollution levels; (iii reducing the temporal variations produced by mobile sensing process; and (iv applying interpolation techniques for creating detailed pollution maps. In addition, we study the best strategy to use mobile sensors by first determining the influence of sensor orientation on the captured values and then analyzing the influence of time and space sampling in the interpolation process.

Mobile high-voltage switchboard. Variable and uncomplicated; Mobile Hochspannungsschaltanlage. Variabel und unkompliziert in der Anwendung

Energy Technology Data Exchange (ETDEWEB)

Albert, Andreas [Siemens AG, Erlangen (Germany). Sector Energy

2009-07-13

The mobile high-voltage switchboard ''REE-Movil 2'' for voltages up to 245 kV provides a complete and nearly autonomous switchboard in a container, a solution that has been available in the medium-voltage sector for some time already. It can be used whenever a quick replacement of a switchboard section or a temporary supplement to a switching substation is needed. The container is mounted on a trailer for maximum flexibility and mobility. (orig.)

High level bacterial contamination of secondary school students' mobile phones.

Science.gov (United States)

Kõljalg, Siiri; Mändar, Rando; Sõber, Tiina; Rööp, Tiiu; Mändar, Reet

2017-06-01

While contamination of mobile phones in the hospital has been found to be common in several studies, little information about bacterial abundance on phones used in the community is available. Our aim was to quantitatively determine the bacterial contamination of secondary school students' mobile phones. Altogether 27 mobile phones were studied. The contact plate method and microbial identification using MALDI-TOF mass spectrometer were used for culture studies. Quantitative PCR reaction for detection of universal 16S rRNA, Enterococcus faecalis 16S rRNA and Escherichia coli allantoin permease were performed, and the presence of tetracycline ( tet A, tet B, tet M), erythromycin ( erm B) and sulphonamide ( sul 1) resistance genes was assessed. We found a high median bacterial count on secondary school students' mobile phones (10.5 CFU/cm 2 ) and a median of 17,032 bacterial 16S rRNA gene copies per phone. Potentially pathogenic microbes ( Staphylococcus aureus , Acinetobacter spp. , Pseudomonas spp., Bacillus cereus and Neisseria flavescens ) were found among dominant microbes more often on phones with higher percentage of E. faecalis in total bacterial 16S rRNA. No differences in contamination level or dominating bacterial species between phone owner's gender and between phone types (touch screen/keypad) were found. No antibiotic resistance genes were detected on mobile phone surfaces. Quantitative study methods revealed high level bacterial contamination of secondary school students' mobile phones.

High mobility ZnO nanowires for terahertz detection applications

International Nuclear Information System (INIS)

Liu, Huiqiang; Peng, Rufang; Chu, Shijin; Chu, Sheng

2014-01-01

An oxide nanowire material was utilized for terahertz detection purpose. High quality ZnO nanowires were synthesized and field-effect transistors were fabricated. Electrical transport measurements demonstrated the nanowire with good transfer characteristics and fairly high electron mobility. It is shown that ZnO nanowires can be used as building blocks for the realization of terahertz detectors based on a one-dimensional plasmon detection configuration. Clear terahertz wave (∼0.3 THz) induced photovoltages were obtained at room temperature with varying incidence intensities. Further analysis showed that the terahertz photoresponse is closely related to the high electron mobility of the ZnO nanowire sample, which suggests that oxide nanoelectronics may find useful terahertz applications.

Use of high metal-containing biogas digestates in cereal production - Mobility of chromium and aluminium.

Science.gov (United States)

Dragicevic, Ivan; Eich-Greatorex, Susanne; Sogn, Trine A; Horn, Svein J; Krogstad, Tore

2018-07-01

Biogas digestate use as organic fertilizer has been widely promoted in recent years as a part of the global agenda on recycling waste and new sustainable energy production. Although many studies have confirmed positive effects of digestates on soil fertility, there is still lack of information on the potential adverse effects of digestates on natural soil heavy metal content, metal leaching and leaching of other pollutants. We have investigated the release of aluminium (Al) and chromium (Cr) from different soils treated with commercial digestates high in mentioned potentially problematic metals in a field experiment, while a greenhouse and a laboratory column experiment were used to address mobility of these metals in two other scenarios. Results obtained from the field experiment showed an increase in total concentrations for both investigated metals on plots treated with digestates as well as a significant increase of water-soluble Al concentrations. Factors that were found to be mostly affecting the metal mobility were dissolved organic carbon (DOC), pH and type of soil. Metal binding and free metal concentrations were modelled using the WHAM 7.0 software. Results indicated that the use of digestates with high metal content are comparable to use of animal manure with respect to metal leaching. Data obtained through chemical modelling for the samples from the field experiment suggested that an environmental risk from higher metal mobility has to be considered for Al. In the greenhouse experiment, measured concentrations of leached Cr at the end of the growing season were low for all treatments, while the concentration of leached Al from digestates was higher. The high irrigation column leaching experiment showed an increased leaching rate of Cr with addition of digestates. Copyright © 2018 Elsevier Ltd. All rights reserved.

High-skilled labour mobility in Europe before and after the 2004 enlargement.

Science.gov (United States)

Petersen, Alexander M; Puliga, Michelangelo

2017-03-01

The extent to which international high-skilled mobility channels are forming is a question of great importance in an increasingly global knowledge-based economy. One factor facilitating the growth of high-skilled labour markets is the standardization of certifiable degrees meriting international recognition. Within this context, we analysed an extensive high-skilled mobility database comprising roughly 382 000 individuals from five broad profession groups (Medical, Education, Technical, Science & Engineering and Business & Legal) over the period 1997-2014, using the 13-country expansion of the European Union (EU) to provide insight into labour market integration. We compare the periods before and after the 2004 enlargement, showing the emergence of a new east-west migration channel between the 13 mostly eastern EU entrants (E) and the rest of the western European countries (W). Indeed, we observe a net directional loss of human capital from E → W, representing 29% of the total mobility after 2004. Nevertheless, the counter-migration from W → E is 7% of the total mobility over the same period, signalling the emergence of brain circulation within the EU. Our analysis of the country-country mobility networks and the country-profession bipartite networks provides timely quantitative evidence for the convergent integration of the EU, and highlights the central role of the UK and Germany as high-skilled labour hubs. We conclude with two data-driven models to explore the structural dynamics of the mobility networks. First, we develop a reconfiguration model to explore the potential ramifications of Brexit and the degree to which redirection of high-skilled labourers away from the UK may impact the integration of the rest of the European mobility network. Second, we use a panel regression model to explain empirical high-skilled mobility rates in terms of various economic 'push-pull' factors, the results of which show that government expenditure on education, per capita

High rate sulfate reduction at pH 6 in a Ph-auxostat submerged membrane bioreactor fed with formate

NARCIS (Netherlands)

Bijmans, M.F.M.; Peeters, T.W.T.; Lens, P.N.L.; Buisman, C.J.N.

2008-01-01

Many industrial waste and process waters contain high concentrations of sulfate, which can be removed by sulfate-reducing bacteria (SRB). This paper reports on mesophilic (30 °C) sulfate reduction at pH 6 with formate as electron donor in a membrane bioreactor with a pH-auxostat dosing system. A

High mobility and quantum well transistors design and TCAD simulation

CERN Document Server

Hellings, Geert

2013-01-01

For many decades, the semiconductor industry has miniaturized transistors, delivering increased computing power to consumers at decreased cost. However, mere transistor downsizing does no longer provide the same improvements. One interesting option to further improve transistor characteristics is to use high mobility materials such as germanium and III-V materials. However, transistors have to be redesigned in order to fully benefit from these alternative materials. High Mobility and Quantum Well Transistors: Design and TCAD Simulation investigates planar bulk Germanium pFET technology in chapters 2-4, focusing on both the fabrication of such a technology and on the process and electrical TCAD simulation. Furthermore, this book shows that Quantum Well based transistors can leverage the benefits of these alternative materials, since they confine the charge carriers to the high-mobility material using a heterostructure. The design and fabrication of one particular transistor structure - the SiGe Implant-Free Qu...

Enhanced electrochemomechanical activity of polyaniline films towards high pH region: contribution of Donnan effect

International Nuclear Information System (INIS)

Takashima, Wataru; Nakashima, Megumi; Pandey, Shyam S.; Kaneto, Keiichi

2004-01-01

Enhancement of electrochemomechanical deformation (ECMD) and expansion of ECMD activity towards high pH have been simultaneously achieved in the electrolytes equilibrated with HCl and NaCl solutions for polyaniline (PANI) film. The maximum deformation has been reached to 6.7% in the mixture of 3 M HCl and 3 M NaCl equilibrated at pH 3 at ambient temperature. By comparing the fact that the ECMD magnitude is 3.2% in 1 M HCl equilibrated at pH 0.5, the simple judicious selection of electrolyte condition leads to the enhancement of ECMD magnitude by around two times. The concentration dependence on both electrical conductivity and absorption spectra elucidates the increase of protonation ratio as a function of electrolyte concentration. The results indicate that the high concentration retains both the electrochemical and ECMD activities in PANI film towards high pH region, which is the enhanced functionality of PANI supported by Donnan effect

pH dependent green synthesis of gold nanoparticles by completely C6-carboxylated curdlan under high temperature and various pH conditions.

Science.gov (United States)

Qiu, Wen-Yi; Wang, Kai; Wang, Yao-Yao; Ding, Zhi-Chao; Wu, Li-Xia; Cai, Wu-Dan; Yan, Jing-Kun

2018-01-01

A C6-carboxylated curdlan (C6-Cc) obtained from 4-acetamido-TEMPO-mediated oxidation of curdlan was used both as a reducing and stabilizing agent for green synthesis of pH-responsive AuNPs, which was carried out by controlling the pH of the C6-Cc solution at a high temperature (100°C). C6-Cc presented a semi-flexible random coil chain in the aqueous medium at pH 5.5 and became more expanded and rigid in alkaline conditions (pH 7.1-12.0), though the primary chemical structure of C6-Cc was virtually unchanged with the pH variation. The AuNPs prepared with C6-Cc at various pHs were characterized by various instrumental measurements. The shapes and sizes of AuNPs were found to be strongly dependent on the pH of the C6-Cc solution. The C6-Cc-decorated AuNPs exhibited a more well-dispersed spherical morphology with smaller particle sizes under alkaline conditions (pH 7.1-12.0). Through this study, a facile, simple, and green method has been demonstrated for preparation of stimuli-sensitive AuNPs using biocompatible polyanionic polysaccharides. Copyright © 2017 Elsevier B.V. All rights reserved.

The sensitivity of particle pH to NH3: Can high NH3 cause London Fog conditions?

Science.gov (United States)

Weber, R. J.; Guo, H.; Nenes, A.

2017-12-01

High ammonia emissions from agriculture or other sources have been suggested to elevate ambient particle pH levels to near neutral acidity (pH=7), a condition that promotes rapid SO2 oxidation by NO2 to form aerosol sulfate concentration consistent with "London fog" levels. This mechanism has been used to explain pollution haze events in China. Predicted pH for locations in the US and Europe show fine particles are highly acidic with pH typically less than 2. The results are consistent with measured ammonia and nitric acid gas-particle partitioning, validating predicted pH levels. Using these data sets from representative sites around the world we conduct a thermodynamic analysis of aerosol pH and its sensitivity to ammonia levels. We find that particle pH, regardless of ammonia levels, is always acidic even for the unusually high ammonia levels found in highly polluted Asian cities, Beijing (pH=4.5) and Xi'an (pH=5), locations where sulfate production from NOx is proposed. These results indicate that sulfur dioxide oxidation through a NO2-mediated pathway is not likely in China, nor any other region of the world (e.g., US, Mediterranean) since the fine aerosol is consistently acidic. The mildly acidic conditions would, however, permit rapid oxidation of sulfur dioxide through transition metal chemistry. The limited alkalinity from the carbonate buffer in dust and seasalt can provide the only likely set of conditions where NO2-mediated oxidation of SO2 outcompetes with other well-established pathways.

Ultimate response time of high electron mobility transistors

International Nuclear Information System (INIS)

Rudin, Sergey; Rupper, Greg; Shur, Michael

2015-01-01

We present theoretical studies of the response time of the two-dimensional gated electron gas to femtosecond pulses. Our hydrodynamic simulations show that the device response to a short pulse or a step-function signal is either smooth or oscillating time-decay at low and high mobility, μ, values, respectively. At small gate voltage swings, U 0  = U g  − U th , where U g is the gate voltage and U th is the threshold voltage, such that μU 0 /L < v s , where L is the channel length and v s is the effective electron saturation velocity, the decay time in the low mobility samples is on the order of L 2 /(μU 0 ), in agreement with the analytical drift model. However, the decay is preceded by a delay time on the order of L/s, where s is the plasma wave velocity. This delay is the ballistic transport signature in collision-dominated devices, which becomes important during very short time periods. In the high mobility devices, the period of the decaying oscillations is on the order of the plasma wave velocity transit time. Our analysis shows that short channel field effect transistors operating in the plasmonic regime can meet the requirements for applications as terahertz detectors, mixers, delay lines, and phase shifters in ultra high-speed wireless communication circuits

High pH ammonia toxicity, and the search for life on the Jovian planets.

Science.gov (United States)

Deal, P H; Souza, K A; Mack, H M

1975-10-01

Jovian plants have enviroments apparently suitable for the evolution of life, but nevertheless, present severe challenges to organisms. One such challenge arises from the presence of ammonia. Ammonia is an efficient biocide, its effect being dependent on pH as well as on concentration. The effects of pH and ammonia concentration were studied separately, where possible, on a variety of organisms, including some isolated from natural enviornments of high pH and/or ammonia concentration. Escherichia coli and Bacillus subtilis are both extremely sensitive to ammonia. An aerobic organism (growth up to pH 11.4) from an alkaline spring is more resistant, but exhibits a toxic response to ammonia at a pH much lower than its maximum for growth. The greatest ammonia resistance has been found in an unidentified organism growing at near neutral pH. Even in this case, however, survival at ammonia concentrations reasonably expected on the Jovian planets is measured in hours. This is, nevertheless, two to three orders of magnitude longer than for E. coli. Our data support the tentative conclusion that contamination of the Jovian planets with terrestrial organisms that can grow is unlikely. However, the range of toxic response noted, coupled with the observation that terrestrial life has not been exposed to high ammonia concentrations for millions of years, suggests that adaptation to greater ammonia tolerance may be possible.

Investigation of Doppler Effects on high mobility OFDM-MIMO systems with the support of High Altitude Platforms (HAPs)

Science.gov (United States)

Mohammed, H. A.; Sibley, M. J. N.; Mather, P. J.

2012-05-01

The merging of Orthogonal Frequency Division Multiplexing (OFDM) with Multiple-input multiple-output (MIMO) is a promising mobile air interface solution for next generation wireless local area networks (WLANs) and 4G mobile cellular wireless systems. This paper details the design of a highly robust and efficient OFDM-MIMO system to support permanent accessibility and higher data rates to users moving at high speeds, such as users travelling on trains. It has high relevance for next generation wireless local area networks (WLANs) and 4G mobile cellular wireless systems. The paper begins with a comprehensive literature review focused on both technologies. This is followed by the modelling of the OFDM-MIMO physical layer based on Simulink/Matlab that takes into consideration high vehicular mobility. Then the entire system is simulated and analysed under different encoding and channel estimation algorithms. The use of High Altitude Platform system (HAPs) technology is considered and analysed.

Investigation of Doppler Effects on high mobility OFDM-MIMO systems with the support of High Altitude Platforms (HAPs)

International Nuclear Information System (INIS)

Mohammed, H A; Sibley, M J N; Mather, P J

2012-01-01

The merging of Orthogonal Frequency Division Multiplexing (OFDM) with Multiple-input multiple-output (MIMO) is a promising mobile air interface solution for next generation wireless local area networks (WLANs) and 4G mobile cellular wireless systems. This paper details the design of a highly robust and efficient OFDM-MIMO system to support permanent accessibility and higher data rates to users moving at high speeds, such as users travelling on trains. It has high relevance for next generation wireless local area networks (WLANs) and 4G mobile cellular wireless systems. The paper begins with a comprehensive literature review focused on both technologies. This is followed by the modelling of the OFDM-MIMO physical layer based on Simulink/Matlab that takes into consideration high vehicular mobility. Then the entire system is simulated and analysed under different encoding and channel estimation algorithms. The use of High Altitude Platform system (HAPs) technology is considered and analysed.

Transport of vanadium (V in saturated porous media: effects of pH, ionic-strength and clay mineral

Directory of Open Access Journals (Sweden)

Yulu Wang

2016-10-01

Full Text Available Vanadium, a hazardous pollutant, has been frequently detected in soil and groundwater, however, its transport behavior in porous media were not clearly understood. In this study, the effects of solution pH, ionic strength (IS and the effect of clay mineral on the transport of vanadium in saturated porous media were investigated. Laboratory experiments using a series of columns packed with quartz sand were carried out to explore the retention and transport of vanadium with a range of ionic-strength (0.001–0.1 M and pH (4–8 and two different types of clay minerals montmorillonite and kaolinite. Results of the breakthrough experiments showed that vanadium was highly mobile in the saturated porous media. The increase in pH rendered a higher transport of vanadium in saturated porous media. The study also indicated an easier transfer of vanadium with an increase in IS. Montmorillonite enhanced the mobility of vanadium in the column when compared to kaolinite. A mathematical model based on advection-dispersion equation coupled with equilibrium and kinetic reactions was used to describe the retention and transport of vanadium in the columns very well.

Ph3CCOOSnPh3.Ph3PO AND Ph3CCOOSnPh3.Ph3AsO: SYNTHESIS AND INFRARED STUDY

Directory of Open Access Journals (Sweden)

ABDOU MBAYE

2014-08-01

Full Text Available The mixture of ethanolic solutions of Ph3CCOOSnPh3 and Ph3PO or Ph3AsO gives Ph3CCOOSnPh3.Ph3PO and Ph3CCOOSnPh3.Ph3AsO adducts which have been characterized by infrared spectroscopy. A discrete structure is suggested for both, the environment around the tin centre being trigonal bipyramidal, the triphenylacetate anion behaving as a mondentate ligand.

Intragastric pH and pressure profiles after intake of the high-caloric, high-fat meal as used for food effect studies.

Science.gov (United States)

Koziolek, M; Schneider, F; Grimm, M; Modeβ, Chr; Seekamp, A; Roustom, T; Siegmund, W; Weitschies, W

2015-12-28

The intraluminal conditions of the fed stomach are critical for drug release from solid oral dosage forms and thus, often associated with the occurrence of food effects on oral bioavailability. In this study, intragastric pH and pressure profiles present after the ingestion of the high-caloric, high-fat (964 kcal) FDA standard breakfast were investigated in 19 healthy human subjects by using the telemetric SmartPill® capsule system (26 × 13 mm). Since the gastric emptying of such large non-digestible objects is typically accomplished by the migrating motor complex phase III activity, the time required for recurrence of fasted state motility determined the gastric emptying time (GET). Following the diet recommendations of the FDA guidance on food effect studies, the mean GET of the telemetric motility capsule was 15.3 ± 4.7 h. Thus, the high caloric value of the standard breakfast impeded gastric emptying before lunch in 18 out of 19 subjects. During its gastric transit, the capsule was exposed to highly dynamic conditions in terms of pH and pressure, which were mainly dependent on further meal and liquid intake, as well as the intragastric capsule deposition behavior. Maximum pH values in the stomach were measured immediately after capsule intake. The median pH value of the 5 min period after capsule ingestion ranged between pH 3.3 and 5.3. Subsequently, the pH decreased relatively constantly and reached minimum values of pH 0-1 after approximately 4 h. The maximum pressure within the stomach amounted to 293 ± 109 mbar and was clearly higher than the maximum pressure measured at the ileocaecal junction (60 ± 35 mbar). The physiological data on the intraluminal conditions within the fed stomach generated in this study will hopefully contribute to a better understanding of food effects on oral drug product performance.

Functionalized magnetic mesoporous silica nanoparticles for U removal from low and high pH groundwater

Energy Technology Data Exchange (ETDEWEB)

Li, Dien, E-mail: dien.li@srs.gov [Savannah River National Laboratory, Aiken, SC 29808 (United States); Egodawatte, Shani [Department of Chemistry, University of Iowa, Iowa City, IA 52242 (United States); Kaplan, Daniel I. [Savannah River National Laboratory, Aiken, SC 29808 (United States); Larsen, Sarah C. [Department of Chemistry, University of Iowa, Iowa City, IA 52242 (United States); Serkiz, Steven M. [Savannah River National Laboratory, Aiken, SC 29808 (United States); Department of Physics and Astronomy, Clemson University, Clemson, SC 29634 (United States); Seaman, John C. [Savannah River Ecology Laboratory, University of Georgia, Aiken, SC 29802 (United States)

2016-11-05

Highlights: • Magnetic mesoporous silica nanoparticles were functionalized with organic molecules. • The functionalized nanoparticles had high surface areas and consistent pore sizes. • The functionalized nanoparticles were easily separated due to their magnetism. • They exhibited high capacity for uranium removal from low- or high-pH groundwater. - Abstract: U(VI) species display limited adsorption onto sediment minerals and synthetic sorbents in pH <4 or pH >8 groundwater. In this work, magnetic mesoporous silica nanoparticles (MMSNs) with magnetite nanoparticle cores were functionalized with various organic molecules using post-synthetic methods. The functionalized MMSNs were characterized using N{sub 2} adsorption-desorption isotherms, thermogravimetric analysis (TGA), transmission electron microscopy (TEM), {sup 13}C cross polarization and magic angle spinning (CPMAS) nuclear magnetic resonance (NMR) spectroscopy, and powder X-ray diffraction (XRD), which indicated that mesoporous silica (MCM-41) particles of 100–200 nm formed around a core of magnetic iron oxide, and the functional groups were primarily grafted into the mesopores of ∼3.0 nm in size. The functionalized MMSNs were effective for U removal from pH 3.5 and 9.6 artificial groundwater (AGW). Functionalized MMSNs removed U from the pH 3.5 AGW by as much as 6 orders of magnitude more than unfunctionalized nanoparticles or silica and had adsorption capacities as high as 38 mg/g. They removed U from the pH 9.6 AGW as much as 4 orders of magnitude greater than silica and 2 orders of magnitude greater than the unfunctionalized nanoparticles with adsorption capacities as high as 133 mg/g. These results provide an applied solution for treating U contamination that occurs at extreme pH environments and a scientific foundation for solving critical industrial issues related to environmental stewardship and nuclear power production.

Highly Sensitive and Wide-Dynamic-Range Multichannel Optical-Fiber pH Sensor Based on PWM Technique.

Science.gov (United States)

Khan, Md Rajibur Rahaman; Kang, Shin-Won

2016-11-09

In this study, we propose a highly sensitive multichannel pH sensor that is based on an optical-fiber pulse width modulation (PWM) technique. According to the optical-fiber PWM method, the received sensing signal's pulse width changes when the optical-fiber pH sensing-element of the array comes into contact with pH buffer solutions. The proposed optical-fiber PWM pH-sensing system offers a linear sensing response over a wide range of pH values from 2 to 12, with a high pH-sensing ability. The sensitivity of the proposed pH sensor is 0.46 µs/pH, and the correlation coefficient R² is approximately 0.997. Additional advantages of the proposed optical-fiber PWM pH sensor include a short/fast response-time of about 8 s, good reproducibility properties with a relative standard deviation (RSD) of about 0.019, easy fabrication, low cost, small size, reusability of the optical-fiber sensing-element, and the capability of remote sensing. Finally, the performance of the proposed PWM pH sensor was compared with that of potentiometric, optical-fiber modal interferometer, and optical-fiber Fabry-Perot interferometer pH sensors with respect to dynamic range width, linearity as well as response and recovery times. We observed that the proposed sensing systems have better sensing abilities than the above-mentioned pH sensors.

Highly Sensitive and Wide-Dynamic-Range Multichannel Optical-Fiber pH Sensor Based on PWM Technique

Science.gov (United States)

Khan, Md. Rajibur Rahaman; Kang, Shin-Won

2016-01-01

In this study, we propose a highly sensitive multichannel pH sensor that is based on an optical-fiber pulse width modulation (PWM) technique. According to the optical-fiber PWM method, the received sensing signal’s pulse width changes when the optical-fiber pH sensing-element of the array comes into contact with pH buffer solutions. The proposed optical-fiber PWM pH-sensing system offers a linear sensing response over a wide range of pH values from 2 to 12, with a high pH-sensing ability. The sensitivity of the proposed pH sensor is 0.46 µs/pH, and the correlation coefficient R2 is approximately 0.997. Additional advantages of the proposed optical-fiber PWM pH sensor include a short/fast response-time of about 8 s, good reproducibility properties with a relative standard deviation (RSD) of about 0.019, easy fabrication, low cost, small size, reusability of the optical-fiber sensing-element, and the capability of remote sensing. Finally, the performance of the proposed PWM pH sensor was compared with that of potentiometric, optical-fiber modal interferometer, and optical-fiber Fabry–Perot interferometer pH sensors with respect to dynamic range width, linearity as well as response and recovery times. We observed that the proposed sensing systems have better sensing abilities than the above-mentioned pH sensors. PMID:27834865

High sensitivity pH sensing on the BEOL of industrial FDSOI transistors

Science.gov (United States)

Rahhal, Lama; Ayele, Getenet Tesega; Monfray, Stéphane; Cloarec, Jean-Pierre; Fornacciari, Benjamin; Pardoux, Eric; Chevalier, Celine; Ecoffey, Serge; Drouin, Dominique; Morin, Pierre; Garnier, Philippe; Boeuf, Frederic; Souifi, Abdelkader

2017-08-01

In this work we demonstrate the use of Fully Depleted Silicon On Insulator (FDSOI) transistors as pH sensors with a 23 nm silicon nitride sensing layer built in the Back-End-Of-Line (BEOL). The back end process to deposit the sensing layer and fabricate the electrical structures needed for testing is detailed. A series of tests employing different pH buffer solutions has been performed on transistors of different geometries, controlled via the back gate. The main findings show a shift of the drain current (ID) as a function of the back gate voltage (VB) when different pH buffer solutions are probed in the range of pH 6 to pH 8. This shift is observed at VB voltages swept from 0 V to 3 V, demonstrating the sensor operation at low voltage. A high sensitivity of up to 250 mV/pH unit (more than 4-fold larger than Nernstian response) is observed on FDSOI MOS transistors of 0.06 μm gate length and 0.08 μm gate width. She is currently working as a Postdoctoral researcher at Institut des nanotechnologies de Lyon in collaboration with STMicroelectronics and Université de Sherbrook (Canada) working on ;Integration of ultra-low-power gas and pH sensors with advanced technologies;. Her research interest includes selection, machining, optimisation and electrical characterisation of the sensitive layer for a low power consumption gas sensor based on advanced MOS transistors.

High electron mobility and large magnetoresistance in the half-Heusler semimetal LuPtBi

KAUST Repository

Hou, Zhipeng

2015-12-18

Materials with high carrier mobility showing large magnetoresistance (MR) have recently received much attention because of potential applications in future high-performance magnetoelectric devices. Here, we report on an electron-hole-compensated half-Heusler semimetal LuPtBi that exhibits an extremely high electron mobility of up to 79000cm2/Vs with a nonsaturating positive MR as large as 3200% at 2 K. Remarkably, the mobility at 300 K is found to exceed 10500cm2/Vs, which is among the highest values reported in three-dimensional bulk materials thus far. The clean Shubnikov–de Haas quantum oscillation observed at low temperatures and the first-principles calculations together indicate that the high electron mobility is due to a rather small effective carrier mass caused by the distinctive band structure of the crystal. Our findings provide a different approach for finding large, high-mobility MR materials by designing an appropriate Fermi surface topology starting from simple electron-hole-compensated semimetals.

The chromatographic behavior of arsenic compounds on anion exchange columns with binary organic acids as mobile phases

Energy Technology Data Exchange (ETDEWEB)

Zheng, J.; Goessler, W.; Kosmus, W. [Graz Univ. (Austria). Inst. fuer Analytische Chemie

1998-03-01

Identification and quantification of arsenic compounds was performed with high-performance liquid chromatography (HPLC) and flame atomic absorption spectrometry (FAAS) as element-specific detector. Arsenous acid, methylarsonic acid, dimethylarsinic acid, arsenic acid, arsenobetaine, and arsenocholine were separated on two anion-exchange columns (Synchropak Q 300 and PRP-X 100) with different binary organic acids as mobile phases. The influence of chromatographic parameters, such as pH and the concentration of the mobile phase were investigated. An unusual chromatographic behavior of arsenous acid was observed when tartaric acid was used as mobile phase. (orig.)

Record high hole mobility in polymer semiconductors via side-chain engineering.

Science.gov (United States)

Kang, Il; Yun, Hui-Jun; Chung, Dae Sung; Kwon, Soon-Ki; Kim, Yun-Hi

2013-10-09

Charge carrier mobility is still the most challenging issue that should be overcome to realize everyday organic electronics in the near future. In this Communication, we show that introducing smart side-chain engineering to polymer semiconductors can facilitate intermolecular electronic communication. Two new polymers, P-29-DPPDBTE and P-29-DPPDTSE, which consist of a highly conductive diketopyrrolopyrrole backbone and an extended branching-position-adjusted side chain, showed unprecedented record high hole mobility of 12 cm(2)/(V·s). From photophysical and structural studies, we found that moving the branching position of the side chain away from the backbone of these polymers resulted in increased intermolecular interactions with extremely short π-π stacking distances, without compromising solubility of the polymers. As a result, high hole mobility could be achieved even in devices fabricated using the polymers at room temperature.

Mobilization of Iron by Plant-Borne Coumarins.

Science.gov (United States)

Tsai, Huei Hsuan; Schmidt, Wolfgang

2017-06-01

Iron is one of the most abundant elements in soils, but its low phytoavailability at high pH restricts plant communities on alkaline soils to taxa that have evolved efficient strategies to increase iron solubility. Recent evidence provides support for a previously underestimated role of root-secreted coumarins in mobilizing iron through reduction and chelation as part of an orchestrated strategy evolved to improve the acquisition of iron from recalcitrant pools. Understanding the mechanisms that tune the production of iron-mobilizing coumarins and their intricate interplay with other biosynthesis pathways could yield clues for deciphering the molecular basis of 'iron efficiency' - the ability of plants to thrive on soils with limited iron availability - and may open avenues for generating iron-fortified crops. Copyright © 2017 Elsevier Ltd. All rights reserved.

Hall mobility of free charge carriers in highly compensated p-Germanium

International Nuclear Information System (INIS)

Gavrilyuk, V.Yi.; Kirnas, Yi.G.; Balakyin, V.D.

2000-01-01

Hall mobility of free charge carriers in initial detectors Ge (Ga) is studied. It is established that an increase in the compensation factor results in the enlargement of Hall mobility in germanium highly compensated by introduction of Li ions during their drift in an electrical field

Spectrophotometric high-precision seawater pH determination for use in underway measuring systems

Directory of Open Access Journals (Sweden)

S. Aßmann

2011-10-01

Full Text Available Autonomous sensors are required for a comprehensive documentation of the changes in the marine carbon system and thus to differentiate between its natural variability and anthropogenic impacts. Spectrophotometric determination of pH – a key variable of the seawater carbon system – is particularly suited to achieve precise and drift-free measurements. However, available spectrophotometric instruments are not suitable for integration into automated measurement systems (e.g. FerryBox since they do not meet the major requirements of reliability, stability, robustness and moderate cost. Here we report on the development and testing of a~new indicator-based pH sensor that meets all of these requirements. This sensor can withstand the rough conditions during long-term deployments on ships of opportunity and is applicable to the open ocean as well as to coastal waters with a complex matrix and highly variable conditions. The sensor uses a high resolution CCD spectrometer as detector connected via optical fibers to a custom-made cuvette designed to reduce the impact of air bubbles. The sample temperature can be precisely adjusted (25 °C ± 0.006 °C using computer-controlled power supplies and Peltier elements thus avoiding the widely used water bath. The overall setup achieves a measurement frequency of 1 min⁻¹ with a precision of ±0.0007 pH units, an average offset of +0.0005 pH units to a reference system, and an offset of +0.0081 pH units to a certified standard buffer. Application of this sensor allows monitoring of seawater pH in autonomous underway systems, providing a key variable for characterization and understanding of the marine carbon system.

High-mobility pyrene-based semiconductor for organic thin-film transistors.

Science.gov (United States)

Cho, Hyunduck; Lee, Sunyoung; Cho, Nam Sung; Jabbour, Ghassan E; Kwak, Jeonghun; Hwang, Do-Hoon; Lee, Changhee

2013-05-01

Numerous conjugated oligoacenes and polythiophenes are being heavily studied in the search for high-mobility organic semiconductors. Although many researchers have designed fused aromatic compounds as organic semiconductors for organic thin-film transistors (OTFTs), pyrene-based organic semiconductors with high mobilities and on-off current ratios have not yet been reported. Here, we introduce a new pyrene-based p-type organic semiconductor showing liquid crystal behavior. The thin film characteristics of this material are investigated by varying the substrate temperature during the deposition and the gate dielectric condition using the surface modification with a self-assembled monolayer, and systematically studied in correlation with the performances of transistor devices with this compound. OTFT fabricated under the optimum deposition conditions of this compound, namely, 1,6-bis(5'-octyl-2,2'-bithiophen-5-yl)pyrene (BOBTP) shows a high-performance transistor behavior with a field-effect mobility of 2.1 cm(2) V(-1) s(-1) and an on-off current ratio of 7.6 × 10(6) and enhanced long-term stability compared to the pentacene thin-film transistor.

The Effect of pH and High-Pressure Homogenization on Droplet Size

Directory of Open Access Journals (Sweden)

Ah Pis Yong

2017-12-01

Full Text Available The aims of this study are to revisit the effect of high pressure on homogenization and the influence of pH on the emulsion droplet sizes. The high-pressure homogenization (HPH involves two stages of processing, where the first stage involves in blending the coarse emulsion by a blender, and the second stage requires disruption of the coarse emulsion into smaller droplets by a high-pressure homogenizer. The pressure range in this review is in between 10-500 MPa. The homogenised droplet sizes can be reduced by increasing the homogenization recirculation, and there is a threshold point beyond that by applying pressure only, the size cannot be further reduced. Normally, homogenised emulsions are classified by their degree of kinetic stability. Dispersed phase present in the form of droplets while continuous phase also known as suspended droplets. With a proper homogenization recirculation and pressure, a more kinetically stable emulsion can be produced. The side effects of increasing homogenization pressure are that it can cause overprocessing of the emulsion droplets where the droplet sizes become larger rather than the expected smaller size. This can cause kinetic instability in the emulsion. The droplet size is usually measured by dynamic light scattering or by laser light scattering technique. The type of samples used in this reviews are such as chocolate and vanilla based powders; mean droplet sizes samples; basil oil; tomato; lupin protein; oil; skim milk, soymilk; coconut milk; tomato homogenate; corn; egg-yolk, rapeseed and sunflower; Poly(4-vinylpyridine/silica; and Complex 1 until complex 4 approaches from author case study. A relationship is developed between emulsion size and pH. Results clearly show that lower pH offers smaller droplet of emulsion and the opposite occurs when the pH is increased.

Stabilizing sodium hypochlorite at high pH: effects on soft tissue and dentin.

Science.gov (United States)

Jungbluth, Holger; Marending, Monika; De-Deus, Gustavo; Sener, Beatrice; Zehnder, Matthias

2011-05-01

When sodium hypochlorite solutions react with tissue, their pH drops and tissue sorption decreases. We studied whether stabilizing a NaOCl solution at a high pH would increase its soft-tissue dissolution capacity and effects on the dentin matrix compared with a standard NaOCl solution of the same concentration and similar initial pH. NaOCl solutions were prepared by mixing (1:1) a 10% stock solution with water (standard) or 2 mol/L NaOH (stabilized). Physiological saline and 1 mol/L NaOH served as the controls. Chlorine content and alkaline capacity of NaOCl solutions were determined. Standardized porcine palatal soft-tissue specimens and human root dentin bars were exposed to test and control solutions. Weight loss percentage was assessed in the soft-tissue dissolution assay. Three-point bending tests were performed on the root dentin bars to determine the modulus of elasticity and flexural strength. Values between groups were compared using one-way analysis of variance with the Bonferroni correction for multiple testing (α pH level of 7.5, respectively. The stabilized NaOCl dissolved significantly more soft tissue than the standard solution, and the pH remained high. It also caused a higher loss in elastic modulus and flexure strength (P < .05) than the control solutions, whereas the standard solution did not. NaOH-stabilized NaOCl solutions have a higher alkaline capacity and are thus more proteolytic than standard counterparts. Copyright © 2011 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Characterisation of mobile radio channels for small multiantenna terminals

DEFF Research Database (Denmark)

Kotterman, Wim Anton Theo

The Ph.D. thesis "Characterisation of mobile radio channels for small multiantenna terminals" discusses the work on and presents the results of the Ph.D. project "Smart antennas for small terminals". The scope of the project was to determine whether the use of multiple antennas on small handheld...... mobile terminals could improve the transmission quality and throughput of mobile communication links under typical usage conditions. That is, using multiple antennas of typical design, handled by users in typical ways in typical environments as handling by users has a strong influence on channel...... for multiantenna operation, and user influences. Additionally, the reduction of rank of narrow band channels on small observation intervals is discussed. One of the consequences is that fading prediction is limited to about less than a wavelength ahead in practical circumstances....

Mobile Learning for Higher Education in Problem-Based Learning Environments

DEFF Research Database (Denmark)

Rongbutsri, Nikorn

2011-01-01

This paper describes the PhD project on Mobile Learning for Higher Education in Problem-Based Learning Environment which aims to understand how students gain benefit from using mobile devices in the aspect of project work collaboration. It demonstrates research questions, theoretical perspective...

High-mobility BaSnO{sub 3} grown by oxide molecular beam epitaxy

Energy Technology Data Exchange (ETDEWEB)

Raghavan, Santosh; Schumann, Timo; Kim, Honggyu; Zhang, Jack Y.; Cain, Tyler A.; Stemmer, Susanne, E-mail: stemmer@mrl.ucsb.edu [Materials Department, University of California, Santa Barbara, California 93106-5050 (United States)

2016-01-01

High-mobility perovskite BaSnO{sub 3} films are of significant interest as new wide bandgap semiconductors for power electronics, transparent conductors, and as high mobility channels for epitaxial integration with functional perovskites. Despite promising results for single crystals, high-mobility BaSnO{sub 3} films have been challenging to grow. Here, we demonstrate a modified oxide molecular beam epitaxy (MBE) approach, which supplies pre-oxidized SnO{sub x}. This technique addresses issues in the MBE of ternary stannates related to volatile SnO formation and enables growth of epitaxial, stoichiometric BaSnO{sub 3}. We demonstrate room temperature electron mobilities of 150 cm{sup 2} V{sup −1} s{sup −1} in films grown on PrScO{sub 3}. The results open up a wide range of opportunities for future electronic devices.

From computational discovery to experimental characterization of a high hole mobility organic crystal.

KAUST Repository

Sokolov, Anatoliy N

2011-08-16

For organic semiconductors to find ubiquitous electronics applications, the development of new materials with high mobility and air stability is critical. Despite the versatility of carbon, exploratory chemical synthesis in the vast chemical space can be hindered by synthetic and characterization difficulties. Here we show that in silico screening of novel derivatives of the dinaphtho[2,3-b:2\\',3\\'-f]thieno[3,2-b]thiophene semiconductor with high hole mobility and air stability can lead to the discovery of a new high-performance semiconductor. On the basis of estimates from the Marcus theory of charge transfer rates, we identified a novel compound expected to demonstrate a theoretic twofold improvement in mobility over the parent molecule. Synthetic and electrical characterization of the compound is reported with single-crystal field-effect transistors, showing a remarkable saturation and linear mobility of 12.3 and 16 cm(2) V(-1) s(-1), respectively. This is one of the very few organic semiconductors with mobility greater than 10 cm(2) V(-1) s(-1) reported to date.

Diketopyrrolopyrrole-diketopyrrolopyrrole-based conjugated copolymer for high-mobility organic field-effect transistors

KAUST Repository

Kanimozhi, Catherine K.

2012-10-10

In this communication, we report the synthesis of a novel diketopyrrolopyrrole-diketopyrrolopyrrole (DPP-DPP)-based conjugated copolymer and its application in high-mobility organic field-effect transistors. Copolymerization of DPP with DPP yields a copolymer with exceptional properties such as extended absorption characteristics (up to ∼1100 nm) and field-effect electron mobility values of >1 cm 2 V -1 s -1. The synthesis of this novel DPP-DPP copolymer in combination with the demonstration of transistors with extremely high electron mobility makes this work an important step toward a new family of DPP-DPP copolymers for application in the general area of organic optoelectronics. © 2012 American Chemical Society.

Antibacterial and antifungal effect of high pH and paraffin wax ...

African Journals Online (AJOL)

The antibacterial and antifungal effects of high pH (9, 10) and paraffin wax were determined. Determination of antibacterial and antifungal activity of the combined treatments was achieved by aerobic mesophilic count of bacteria and fungi on the surface of the tomatoes, peppers and oranges using serial dilution and pour ...

Long photoperiods sustain high pH in Arctic kelp forests.

Science.gov (United States)

Krause-Jensen, Dorte; Marbà, Núria; Sanz-Martin, Marina; Hendriks, Iris E; Thyrring, Jakob; Carstensen, Jacob; Sejr, Mikael Kristian; Duarte, Carlos M

2016-12-01

Concern on the impacts of ocean acidification on calcifiers, such as bivalves, sea urchins, and foraminifers, has led to efforts to understand the controls on pH in their habitats, which include kelp forests and seagrass meadows. The metabolism of these habitats can lead to diel fluctuation in pH with increases during the day and declines at night, suggesting no net effect on pH at time scales longer than daily. We examined the capacity of subarctic and Arctic kelps to up-regulate pH in situ and experimentally tested the role of photoperiod in determining the capacity of Arctic macrophytes to up-regulate pH. Field observations at photoperiods of 15 and 24 hours in Greenland combined with experimental manipulations of photoperiod show that photoperiods longer than 21 hours, characteristic of Arctic summers, are conducive to sustained up-regulation of pH by kelp photosynthesis. We report a gradual increase in pH of 0.15 units and a parallel decline in pCO 2 of 100 parts per million over a 10-day period in an Arctic kelp forest over midsummer, with ample scope for continued pH increase during the months of continuous daylight. Experimental increase in CO 2 concentration further stimulated the capacity of macrophytes to deplete CO 2 and increase pH. We conclude that long photoperiods in Arctic summers support sustained up-regulation of pH in kelp forests, with potential benefits for calcifiers, and propose that this mechanism may increase with the projected expansion of Arctic vegetation in response to warming and loss of sea ice.

Sensing interrail mobility

DEFF Research Database (Denmark)

Jensen, Martin Trandberg

methodologies, this doctoral thesis explores the analytical prospects of non-representational theories in tourism research. The dissertation points toward a richer understanding of the ‘social’ which encompasses under-researched topics such as the implications of affective atmospheres, the sensuous and vibrant...... of Culture and Global Studies, Aalborg University, Campus Copenhagen. ’Sensing interrail mobility: Towards multimodal methodologies’ is his Ph.d. dissertation....

Mobile learning and high-lighting language education

DEFF Research Database (Denmark)

Vinther, Jane

Mobile learning and high-profiling language education. The number of students learning a second or foreign language and participating in instruction in languages other than English has been in decline for some time. There seems to be such a general tendency across nations albeit for a variety...... of reasons idiosyncratic to the particular national conditions. This paper gives an account of a diversified national project designed to infuse foreign language learning classes in upper secondary schools in Denmark with renewed enthusiasm through systematically experimenting with the new media by taking...... advantage of the social side in their application. The aim has been to make language classes attractive and relevant and to highlight the attractiveness and fun in learning through web 2.0 and mobile units. The overall project was supported by the Danish ministry of education as well as the individual...

Channel mobility degradation and charge trapping in high-k/metal gate NMOSFETs

International Nuclear Information System (INIS)

Mathew, Shajan; Bera, L.K.; Balasubramanian, N.; Joo, M.S.; Cho, B.J.

2004-01-01

NMOSFETs with Metalo-Organic Chemical Vapor Deposited (MOCVD) HfAlO gate dielectric and TiN metal gate have been fabricated. Channel electron mobility was measured using the split-CV method and compared with SiO 2 devices. All high-k devices showed lower mobility compared with SiO 2 reference devices. High-k MOSFETs exhibited significant charge trapping and threshold instability. Threshold voltage recovery with time was studied on devices with oxide/nitride interfacial layer between high-k film and silicon substrate

Modeling retention and selectivity as a function of pH and column temperature in liquid chromatography.

Science.gov (United States)

Gagliardi, Leonardo G; Castells, Cecilia B; Ràfols, Clara; Rosés, Martí; Bosch, Elisabeth

2006-08-15

In reversed-phase liquid chromatography (RPLC), the retention of weak acids and bases is a sigmoidal function of the mobile-phase pH. Therefore, pH is a key chromatographic variable to optimize retention and selectivity. Furthermore, at an eluent pH close to the pKa of the solute, the dependence of ionization of the buffer and solute on temperature can be used to improve chromatographic separations involving ionizable solutes by an adequate handling of column temperature. In this paper, we derive a general equation for the prediction of the retentive behavior of ionizable compounds upon simultaneous changes in mobile-phase pH and column temperature. Four experiments, two limiting pH values and two temperatures, provide the input data that allow predictions in the whole range of these two variables, based on the thermodynamic fundamentals of the involved equilibria. Also, the study demonstrates the significant role that the choice of the buffer compound would have on selectivity factors in RPLC at temperatures higher than 25 degrees C.

Scattering and mobility in indium gallium arsenide channel, pseudomorphic high electron mobility transistors (InGaAs pHEMTs)

International Nuclear Information System (INIS)

Pearson, J.L.

1999-03-01

Extensive transport measurements have been completed on deep and shallow-channelled InGaAs p-HEMTs of varying growth temperature, indium content, spacer thickness and doping density, with a view to a thorough characterisation, both in the metallic and the localised regimes. Particular emphasis was given to MBE grown layers, with characteristics applicable for device use, but low measurement temperatures were necessary to resolve the elastic scattering mechanisms. Measurements made in the metallic regime included transport and quantum mobility - the former over a range of temperatures between 1.5K to 300K. Conductivity measurements were also acquired in the strong localisation regime between about 1.5K and 100K. Experimentally determined parameters were tested for comparison with those predicted by an electrostatic model. Excellent agreement was obtained for carrier density. Other parameters were less well predicted, but the relevant experimental measurements, including linear depletion of the 2DEG, were sensitive to any excess doping above a 'critical' value determined by the model. At low temperature (1.5K), it was found that in all samples tested, transport mobility was strongly limited at all carrier densities by a large q mechanism, possibly intrinsic to the channel. This was ascribed either to scattering by the long-range potentials arising from the indium concentration fluctuations or fluctuations in the thickness of the channel layer. This mechanism dominates the transport at low carrier densities for all samples, but at high carrier density, an additional mechanism is significant for samples with the thinnest spacers tested (2.5nm). This is ascribed to direct electron interaction with the states of the donor layer, and produces a characteristic transport mobility peak. At higher carrier densities, past the peak, quantum mobility was found only to increase monotonically in value. Remote ionised impurity scattering while significant, particularly for samples

Intracellular product recycling in high succinic acid producing yeast at low pH

NARCIS (Netherlands)

Wahl, S.A.; Bernal Martinez, C.; Zhao, Zheng; van Gulik, W.M.; Jansen, Mickel L.A.

2017-01-01

Background: The metabolic engineering of Saccharomyces cerevisiae for the production of succinic acid has progressed dramatically, and a series of high-producing hosts are available. At low cultivation pH and high titers, the product transport can become bidirectional, i.e. the acid is reentering

Comparison of High-Flexion Fixed-Bearing and High-Flexion Mobile-Bearing Total Knee Arthroplasties-A Prospective Randomized Study.

Science.gov (United States)

Kim, Young-Hoo; Park, Jang-Won; Kim, Jun-Shik

2018-01-01

There is none, to our knowledge, about comparison of high-flexion fixed-bearing and high-flexion mobile-bearing total knee arthroplasties (TKAs) in the same patients. The purpose of this study was to determine whether clinical results; radiographic and computed tomographic scan results; and the survival rate of a high-flexion mobile-bearing TKA is better than that of a high-flexion fixed-bearing TKA. The present study consisted of 92 patients (184 knees) who underwent same-day bilateral TKA. Of those, 17 were men and 75 were women. The mean age at the time of index arthroplasty was 61.5 ± 8.3 years (range 52-65 years). The mean body mass index was 26.2 ± 3.3 kg/m 2 (range 23-34 kg/m 2 ). The mean follow-up was 11.2 years (range 10-12 years). The Knee Society knee scores (93 vs 92 points; P = .531) and function scores (80 vs 80 points; P = 1.000), WOMAC scores (14 vs 15 points; P = .972), and UCLA activity scores (6 vs 6 points; P = 1.000) were not different between the 2 groups at 12 years follow-up. There were no differences in any radiographic and CT scan parameters between the 2 groups. Kaplan-Meier survivorship of the TKA component was 98% (95% confidence interval, 93-100) in the high-flexion fixed-bearing TKA group and 99% (95% confidence interval, 94-100) in the high-flexion mobile-bearing TKA group 12 years after the operation. We found no benefit to mobile-bearing TKA in terms of pain, function, radiographic and CT scan results, and survivorship. Longer-term follow-up is necessary to prove the benefit of the high-flexion mobile-bearing TKA over the high-flexion fixed-bearing TKA. Copyright © 2017 Elsevier Inc. All rights reserved.

One-to-One Mobile Technology in High School Physics Classrooms: Understanding Its Use and Outcome

Science.gov (United States)

Zhai, Xiaoming; Zhang, Meilan; Li, Min

2018-01-01

This study examined ways in which high school students used mobile devices in physics classrooms and after school, and the impact of in-class and after-school mobile technology use on their physics learning performance and interest. We collected data from 803 high school freshmen in China after they had used mobile devices for over five months. A…

Mobilities of slow electrons in low- and high-pressure gases and liquids

International Nuclear Information System (INIS)

Christophorou, L.G.

1975-01-01

Mobilities of slow (thermal and epithermal) electrons in low- (less than or approximately 500 Torr) and high- (approximately 500 to approximately 34,111 Torr) pressure gases are discussed and are related to the molecular structure and to the mobilities of thermal electrons in liquid media

Long photoperiods sustain high pH in Arctic kelp forests

DEFF Research Database (Denmark)

Krause-Jensen, Dorte; Marbà, Núria; Sanz-Martin, M.

2016-01-01

Concern on the impacts of ocean acidification on calcifiers, such as bivalves, sea urchins, and foraminifers, has led to efforts to understand the controls on pH in their habitats, which include kelp forests and seagrass meadows. The metabolism of these habitats can lead to diel fluctuation in pH...... with increases during the day and declines at night, suggesting no net effect on pH at time scales longer than daily. We examined the capacity of subarctic and Arctic kelps to up-regulate pH in situ and experimentally tested the role of photoperiod in determining the capacity of Arctic macrophytes to up......-regulate pH. Field observations at photoperiods of 15 and 24 hours in Greenland com- bined with experimental manipulations of photoperiod show that photoperiods longer than 21 hours, characteristic of Arctic summers, are conducive to sustained up-regulation of pH by kelp photosynthesis. We report a gradual...

Monolayer CS as a metal-free photocatalyst with high carrier mobility and tunable band structure: a first-principles study

Science.gov (United States)

Yang, Xiao-Le; Ye, Xiao-Juan; Liu, Chun-Sheng; Yan, Xiao-Hong

2018-02-01

Producing hydrogen fuel using suitable photocatalysts from water splitting is a feasible method to harvest solar energy. A desired photocatalyst is expected to have suitable band gap, moderate band edge position, and high carrier mobility. By employing first-principles calculations, we explore a α-CS monolayer as a metal-free efficient photocatalyst. The α-CS monolayer shows good energetic, dynamic, and thermal stabilities and is insoluble in water, suggesting its experimental practicability. Monolayer and bilayer α-CS present not only appropriate band gaps for visible and ultraviolet light absorption but also moderate band alignments with water redox potentials in pH neutral water. Remarkably, the α-CS monolayer exhibits high (up to 8453.19 cm2 V-1s-1 for hole) and anisotropic carrier mobility, which is favorable to the migration and separation of photogenerated carriers. In addition, monolayer α-CS experiences an interesting semiconductor-metal transition by applying uniaxial strain and external electric field. Moreover, α-CS under certain strain and electric field is still dynamically stable with the absence of imaginary frequencies. Furthermore, we demonstrate that the graphite (0 0 1) surface is a potential substrate for the α-CS growth with the intrinsic properties of α-CS maintaining. Therefore, our results could pave the way for the application of α-CS as a promising photocatalyst.

Turnover-dependent inactivation of the nitrogenase MoFe-protein at high pH.

Science.gov (United States)

Yang, Kun-Yun; Haynes, Chad A; Spatzal, Thomas; Rees, Douglas C; Howard, James B

2014-01-21

Proton uptake accompanies the reduction of all known substrates by nitrogenase. As a consequence, a higher pH should limit the availability of protons as a substrate essential for turnover, thereby increasing the proportion of more highly reduced forms of the enzyme for further study. The utility of the high-pH approach would appear to be problematic in view of the observation reported by Pham and Burgess [(1993) Biochemistry 32, 13725-13731] that the MoFe-protein undergoes irreversible protein denaturation above pH 8.65. In contrast, we found by both enzyme activity and crystallographic analyses that the MoFe-protein is stable when incubated at pH 9.5. We did observe, however, that at higher pHs and under turnover conditions, the MoFe-protein is slowly inactivated. While a normal, albeit low, level of substrate reduction occurs under these conditions, the MoFe-protein undergoes a complex transformation; initially, the enzyme is reversibly inhibited for substrate reduction at pH 9.5, yet in a second, slower process, the MoFe-protein becomes irreversibly inactivated as measured by substrate reduction activity at the optimal pH of 7.8. The final inactivated MoFe-protein has an increased hydrodynamic radius compared to that of the native MoFe-protein, yet it has a full complement of iron and molybdenum. Significantly, the modified MoFe-protein retains the ability to specifically interact with its nitrogenase partner, the Fe-protein, as judged by the support of ATP hydrolysis and by formation of a tight complex with the Fe-protein in the presence of ATP and aluminum fluoride. The turnover-dependent inactivation coupled to conformational change suggests a mechanism-based transformation that may provide a new probe of nitrogenase catalysis.

Feasible metabolisms in high pH springs of the Philippines.

Science.gov (United States)

Cardace, Dawn; Meyer-Dombard, D'Arcy R; Woycheese, Kristin M; Arcilla, Carlo A

2015-01-01

A field campaign targeting high pH, H2-, and CH4-emitting serpentinite-associated springs in the Zambales and Palawan Ophiolites of the Philippines was conducted in 2012-2013, and enabled description of several springs sourced in altered pillow basalts, gabbros, and peridotites. We combine field observations of pH, temperature, conductivity, dissolved oxygen, and oxidation-reduction potential with analyses of major ions, dissolved inorganic carbon, dissolved organic carbon, and dissolved gas phases in order to model the activities of selected phases important to microbial metabolism, and to rank feasible metabolic reactions based on energy yield. We document changing geochemical inventories in these springs between sampling years, and examine how the environment supports or prevents the function of certain microbial metabolisms. In all, this geochemistry-based assessment of feasible metabolisms indicates methane cycling, hydrogen oxidation, some iron and sulfur metabolisms, and ammonia oxidation are feasible reactions in this continental site of serpentinization.

Arsenic mobilization in an oxidizing alkaline groundwater: Experimental studies, comparison and optimization of geochemical modeling parameters

International Nuclear Information System (INIS)

Hafeznezami, Saeedreza; Lam, Jacquelyn R.; Xiang, Yang; Reynolds, Matthew D.; Davis, James A.; Lin, Tiffany; Jay, Jennifer A.

2016-01-01

Arsenic (As) mobilization and contamination of groundwater affects millions of people worldwide. Progress in developing effective in-situ remediation schemes requires the incorporation of data from laboratory experiments and field samples into calibrated geochemical models. In an oxidizing aquifer where leaching of high pH industrial waste from unlined surface impoundments led to mobilization of naturally occurring As up to 2 mg L −1 , sequential extractions of solid phase As as well as, batch sediment microcosm experiments were conducted to understand As partitioning and solid-phase sorptive and buffering capacity. These data were combined with field data to create a series of geochemical models of the system with modeling programs PHREEQC and FITEQL. Different surface complexation modeling approaches, including component additivity (CA), generalized composite (GC), and a hybrid method were developed, compared and fitted to data from batch acidification experiments to simulate potential remediation scenarios. Several parameters strongly influence the concentration of dissolved As including pH, presence of competing ions (particularly phosphate) and the number of available sorption sites on the aquifer solids. Lowering the pH of groundwater to 7 was found to have a variable, but limited impact (<63%) on decreasing the concentration of dissolved As. The models indicate that in addition to lowering pH, decreasing the concentration of dissolved phosphate and/or increasing the number of available sorption sites could significantly decrease the As solubility to levels below 10 μg L −1 . The hybrid and GC modeling results fit the experimental data well (NRMSE<10%) with reasonable effort and can be implemented in further studies for validation. - Highlights: • Samples were collected from an oxidizing aquifer where high pH waste has led to mobilization of naturally occurring As. • Three surface complexation modeling approaches were used in modeling adsorption

Molybdenum (6) determination by the method of high-frequency and pH titration

International Nuclear Information System (INIS)

Lukianets, I.G.; Kulish, N.G.

1981-01-01

A possibility to determine Mo(6) using the method of high frequency and pH-metric titration is investigated. By means of the high frequency contact R-cell Mo(6) titration is performed using different precipitators: 8-oxiquinoline, lead nitrate and acetate and silver nitrate. It is established that the best conditions are achieved during titration of 67.2-1343 mg/10 ml Mo(6) with lead acetate (pH 4.5-6.5). Relative standard deviation Ssub(r) constitutes 0.005 pH-metric titration of Mo(6) with complexone 3 is studied. The range of Mo(6) concentrations determined constitutes 13.43-134.3 mg at pH initial value of 3.5-5.5. Relative standard deviation Ssub(r) constitutes 0.003. Techniques of molybdenum determination in ferromolybdenum using the method of high frequency and pH-metric titration are developed [ru

Organic High Electron Mobility Transistors Realized by 2D Electron Gas.

Science.gov (United States)

Zhang, Panlong; Wang, Haibo; Yan, Donghang

2017-09-01

A key breakthrough in inorganic modern electronics is the energy-band engineering that plays important role to improve device performance or develop novel functional devices. A typical application is high electron mobility transistors (HEMTs), which utilizes 2D electron gas (2DEG) as transport channel and exhibits very high electron mobility over traditional field-effect transistors (FETs). Recently, organic electronics have made very rapid progress and the band transport model is demonstrated to be more suitable for explaining carrier behavior in high-mobility crystalline organic materials. Therefore, there emerges a chance for applying energy-band engineering in organic semiconductors to tailor their optoelectronic properties. Here, the idea of energy-band engineering is introduced and a novel device configuration is constructed, i.e., using quantum well structures as active layers in organic FETs, to realize organic 2DEG. Under the control of gate voltage, electron carriers are accumulated and confined at quantized energy levels, and show efficient 2D transport. The electron mobility is up to 10 cm 2 V -1 s -1 , and the operation mechanisms of organic HEMTs are also argued. Our results demonstrate the validity of tailoring optoelectronic properties of organic semiconductors by energy-band engineering, offering a promising way for the step forward of organic electronics. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A wide range and highly sensitive optical fiber pH sensor using polyacrylamide hydrogel

Science.gov (United States)

Pathak, Akhilesh Kumar; Singh, Vinod Kumar

2017-12-01

In the present study we report the fabrication and characterization of no-core fiber sensor (NCFS) using smart hydrogel coating for pH measurement. The no-core fiber (NCF) is stubbed between two single-mode fibers with SMA connector before immobilizing of smart hydrogel. The wavelength interrogation technique is used to calculate the sensitivity of the proposed sensor. The result shows a high sensitivity of 1.94 nm/pH for a wide range of pH values varied from 3 to 10 with a good linear response. In addition to high sensitivity, the fabricated sensor provides a fast response time with a good stability, repeatability and reproducibility.

Virtual Lab Experiment: Physics Educational Technology (PhETPhoto Electric Effect for Senior High School

Directory of Open Access Journals (Sweden)

Supurwoko Supurwoko

2017-12-01

Full Text Available This paper introduced these Physics Educational Technology (PhET Simulation and demonstrated their utility for Senior High School Students. The PhET simulations are very involved, interactive animated environments that create a unique opportunity for students. In each case, we demonstrate that discussion simulations are more productive, for developing student conceptual understanding  for photo electric effect than traditional discussion without simulations. During the discussion with PhET simulation, students can construct their  understanding about concepts photo electric effect within this framework. Students learn by building on their prior understanding through a series of constrained and supportives exploration. The simulations support an interactive approach and constrain students productively.

Effect of pH and soil structure on transport of sulfonamide antibiotics in agricultural soils.

Science.gov (United States)

Park, Jong Yol; Huwe, Bernd

2016-06-01

We investigated the effect of solution pH and soil structure on transport of sulfonamide antibiotics (sulfamethoxazole, sulfadimethoxine and sulfamethazine) in combination with batch sorption tests and column experiments. Sorption isotherms properly conformed to Freundlich model, and sorption potential of the antibiotics is as follows; sulfadimethoxine > sulfamethoxazole > sulfamethazine. Decreasing pH values led to increased sorption potential of the antibiotics on soil material in pH range of 4.0-8.0. This likely resulted from abundance of neutral and positive-charged sulfonamides species at low pH, which electrostatically bind to sorption sites on soil surface. Due to destruction of macropore channels, lower hydraulic conductivities of mobile zone were estimated in the disturbed soil columns than in the undisturbed soil columns, and eventually led to lower mobility of the antibiotics in disturbed column. The results suggest that knowledge of soil structure and solution condition is required to predict fate and distribution of sulfonamide antibiotics in environmental matrix. Copyright © 2016 Elsevier Ltd. All rights reserved.

Feasible Metabolic Schema Associated with High pH Springs in the Philippines

Directory of Open Access Journals (Sweden)

DAWN eCARDACE

2015-02-01

Full Text Available A field campaign targeting high pH springs in the Zambales and Palawan Ophiolites of the Philippines was conducted in 2012-2013, and enabled description of several springs sourced in altered pillow basalts, gabbros, and peridotites. We combine field observations of pH, temperature, conductivity, dissolved oxygen, and oxidation-reduction potential with analyses of major ions, dissolved inorganic carbon, dissolved organic carbon, and dissolved gas phases in order to model the activities of selected phases important to microbial metabolism, and to evaluate feasible metabolic reactions based on energy yield. We document changing geochemical inventories in these springs, and examine how the environment supports or prevents the function of certain microbial metabolisms.

Global career mobility, repatriation and career success of Dutch and Indian professionals

NARCIS (Netherlands)

Valk, Reimara

2016-01-01

This PhD research explores global career mobility of Dutch and Indian professionals categorized in three groups: 1) Company-Assigned Expatriates (CAEs);2) Independent Internationally Mobile Professionals (IIMPs) / Self-Initiated Expatriates (SIEs); 3) Repatriates.The purpose was to:- explore the

Analytical admittance characterization of high mobility channel

Energy Technology Data Exchange (ETDEWEB)

Mammeri, A. M.; Mahi, F. Z., E-mail: fati-zo-mahi2002@yahoo.fr [Institute of Science and Technology, University of Bechar (Algeria); Varani, L. [Institute of Electronics of the South (IES - CNRS UMR 5214), University of Montpellier (France)

2015-03-30

In this contribution, we investigate the small-signal admittance of the high electron mobility transistors field-effect channels under a continuation branching of the current between channel and gate by using an analytical model. The analytical approach takes into account the linearization of the 2D Poisson equation and the drift current along the channel. The analytical equations discuss the frequency dependence of the admittance at source and drain terminals on the geometrical transistor parameters.

Effect of some factors on foliar absorption and mobility of Fe59 in plant

International Nuclear Information System (INIS)

Mohamed, F.A.

1990-01-01

Three experiments were conducted under greenhouse conditions using Fe 59 and seedlings of guava and orange to study the effect of PH value (3-8), Fe SO 4 concentrations in combination with three values of PH on foliar absorption and mobility of Fe. In addition, a comparative study to evaluate some compounds of iron for foliar spray was achieved. Foliar absorption of Fe 59 by guava leaves and its mobility were considerably influenced by PH value of spray solution. Maximum absorption and translocation were observed at PH 6. However, most of the absorbed iron 'about 90%' was retained in the treated leaves and the portion 'about 10%' acropetally and basipetally translocated. Upward transport of iron was more pronounced than downward one. Total iron in plant derived from applied FeSO 4 was greatly increased, whereas utilization percent of it was reduced by increasing the rate of Fe in spray solution. Generally, FeSO 4 had a good efficiency which ranged from about 25-43%. Specific absorption of iron by orange leaves was higher than that of guava leaves. From plant nutritional point of view, efficiency of FeSo 4 , Fe-metalosate and multi mineral-metalosate as different sources of Fe through foliar application remarkably varied and FeSO 4 was highly efficient one in comparison with metalosate compounds

PH measurement under pressure and at high temperatures; Mesure du pH sous pression et a temperature elevee

Energy Technology Data Exchange (ETDEWEB)

Fournie, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Le Peintre, M; Mahieu, C [Centre National de la Recherche Scientifique (CNRS), 91 - Gif-sur-Yvette (France)

1961-07-01

In the first part the development and operation of a glass electrode under pressure at room temperature is described. The pressure equilibrium between the inside and outside of the glass membrane several centimetres thick is obtained instantaneously by means of a siphon. The use of a silicone oil as electrical insulator makes possible the working of the glass electrode with the siphon at high pressures (100 kg/cm{sup 2}). In the second part, we determined the pH of various buffer solutions up to 250 deg. C using a cell of our design having two hydrogen electrodes. The values thus obtained for the buffer solutions make it possible to verify and calibrate the pH electrodes independently of the oxido-reduction potential of the medium. In the third part we give the results obtained up to 200 deg. C with the glass electrodes developed in conjunction with the Societe St Gobain. (author) [French] Dans une premiere partie, nous exposons la mise au point et le fonctionnement d'une electrode en verre sous pression a la temperature ordinaire. L'equilibrage instantane de la pression a l'interieur et a l'exterieur de la membrane en verre de quelques diziemes de millimetres d'epaisseur s'effectue par l'intermediaire d'un siphon. L'emploi d'une huile de silicone comme isolant electrique a permis le fonctionnement de l'electrode en verre a siphon sous haute pression (1000 kg/cm{sup 2}). Dans une deuxieme partie, nous avons determine jusqu'a 250 deg. C les valeurs du pH des diverses solutions tampons avec une cellule de notre conception a deux electrodes d'hydrogene. Les valeurs des solutions tampons ainsi obtenues permettent de verifier et d'etalonner les electrodes a pH independantes du potentiel d'oxydo-reduction du milieu. Dans une troisieme partie, nous relatons les resultats obtenus jusqu'a 200 deg. C avec les electrodes en verre mis au point en collaboration avec la Societe Saint-Gobain. (auteur)

High Sensitivity pH Sensor Based on Porous Silicon (PSi) Extended Gate Field-Effect Transistor.

Science.gov (United States)

Al-Hardan, Naif H; Abdul Hamid, Muhammad Azmi; Ahmed, Naser M; Jalar, Azman; Shamsudin, Roslinda; Othman, Norinsan Kamil; Kar Keng, Lim; Chiu, Weesiong; Al-Rawi, Hamzah N

2016-06-07

In this study, porous silicon (PSi) was prepared and tested as an extended gate field-effect transistor (EGFET) for pH sensing. The prepared PSi has pore sizes in the range of 500 to 750 nm with a depth of approximately 42 µm. The results of testing PSi for hydrogen ion sensing in different pH buffer solutions reveal that the PSi has a sensitivity value of 66 mV/pH that is considered a super Nernstian value. The sensor considers stability to be in the pH range of 2 to 12. The hysteresis values of the prepared PSi sensor were approximately 8.2 and 10.5 mV in the low and high pH loop, respectively. The result of this study reveals a promising application of PSi in the field for detecting hydrogen ions in different solutions.

Random demographic household surveys in highly mobile pastoral communities in Chad.

Science.gov (United States)

Weibel, Daniel; Béchir, Mahamat; Hattendorf, Jan; Bonfoh, Bassirou; Zinsstag, Jakob; Schelling, Esther

2011-05-01

Reliable demographic data is a central requirement for health planning and management, and for the implementation of adequate interventions. This study addresses the lack of demographic data on mobile pastoral communities in the Sahel. A total of 1081 Arab, Fulani and Gorane women and 2541 children (1336 boys and 1205 girls) were interviewed and registered by a biometric fingerprint scanner in five repeated random transect demographic and health surveys conducted from March 2007 to January 2008 in the Lake Chad region in Chad. Important determinants for the planning and implementation of household surveys among mobile pastoral communities include: environmental factors; availability of women for interviews; difficulties in defining "own" children; the need for information-education-communication campaigns; and informed consent of husbands in typically patriarchal societies. Due to their high mobility, only 5% (56/1081) of registered women were encountered twice. Therefore, it was not possible to establish a demographic and health cohort. Prospective demographic and health cohorts are the most accurate method to assess child mortality and other demographic indices. However, their feasibility in a highly mobile pastoral setting remains to be shown. Future interdisciplinary scientific efforts need to target innovative methods, tools and approaches to include marginalized communities in operational health and demographic surveillance systems.

Mobile Workforce, Mobile Technology, Mobile Threats

International Nuclear Information System (INIS)

Garcia, J.

2015-01-01

Mobile technologies' introduction into the world of safeguards business processes such as inspection creates tremendous opportunity for novel approaches and could result in a number of improvements to such processes. Mobile applications are certainly the wave of the future. The success of the application ecosystems has shown that users want full fidelity, highly-usable, simple purpose applications with simple installation, quick responses and, of course, access to network resources at all times. But the counterpart to opportunity is risk, and the widespread adoption of mobile technologies requires a deep understanding of the threats and vulnerabilities inherent in mobile technologies. Modern mobile devices can be characterized as small computers. As such, the threats against computing infrastructure apply to mobile devices. Meanwhile, the attributes of mobile technology that make it such an obvious benefit over traditional computing platforms all have elements of risk: pervasive, always-on networking; diverse ecosystems; lack of centralized control; constantly shifting technological foundations; intense competition among competitors in the marketplace; the scale of the installation base (from millions to billions); and many more. This paper will explore the diverse and massive environment of mobile, the number of attackers and vast opportunities for compromise. The paper will explain how mobile devices prove valuable targets to both advanced and persistent attackers as well as less-skilled casual hackers. Organized crime, national intelligence agencies, corporate espionage are all part of the landscape. (author)

International academic mobility: towards a concentration of the minds in Europe

NARCIS (Netherlands)

van der Wende, Marijk

2015-01-01

International mobility of academics has risen over the last few decades, especially among PhD students and post-docs. This may be the result of deliberate policies to stimulate such mobility on the one hand and of growing imbalances in academic career opportunities on the other. The general belief

Gravel Mobility in a High Sand Content Riverbed

Science.gov (United States)

Haschenburger, J. K.

2017-12-01

In sand-gravel channels, sand may modify gravel transport by changing conditions of entrainment and promoting longer displacements or gravel may inhibit sand transport if concentrated into distinct deposits, which restrict sand supply with consequences for migrating bedform size or form. This study reports on gravel mobility in the lower San Antonio River, Texas, where gravel content in the bed material ranges from about 1% to more than 20%. Sediment transport observations were collected at three U.S. Geological Survey gauging stations by deploying a Helley-Smith sampler with a 0.2 mm mesh bag from which transport rates and mobile grain sizes were determined. The flow rates sampled translate into an annual exceedance expectation from 0.2% to 98%. Gravel transport rates are generally two orders of magnitude smaller than the rates of sand transport. However, the finest gravels are transported at rates on the same order of magnitude as the coarsest sands. At all sites, the 2 and 2.8 mm fractions are transported at the lowest flow rate sampled, suggesting mobility for at least 38% to as much as 98% of the year. Fractions as large as 8 mm are mobilized at flow rates that are expected between 25% and 53% of the year. The largest fractions captured in the sampling (16 to 32 mm) require flows closer to bankfull conditions that occur no more than 0.8% of the year. Results document that some gravel sizes can be frequently transported in low gradient riverbeds with high sand content.

Dental plaque pH variation with regular soft drink, diet soft drink and high energy drink: an in vivo study.

Science.gov (United States)

Jawale, Bhushan Arun; Bendgude, Vikas; Mahuli, Amit V; Dave, Bhavana; Kulkarni, Harshal; Mittal, Simpy

2012-03-01

A high incidence of dental caries and dental erosion associated with frequent consumption of soft drinks has been reported. The purpose of this study was to evaluate the pH response of dental plaque to a regular, diet and high energy drink. Twenty subjects were recruited for this study. All subjects were between the ages of 20 and 25 and had at least four restored tooth surfaces present. The subjects were asked to refrain from brushing for 48 hours prior to the study. At baseline, plaque pH was measured from four separate locations using harvesting method. Subjects were asked to swish with 15 ml of the respective soft drink for 1 minute. Plaque pH was measured at the four designated tooth sites at 5, 10 and 20 minutes intervals. Subjects then repeated the experiment using the other two soft drinks. pH was minimum for regular soft drink (2.65 ± 0.026) followed by high energy drink (3.39 ± 0.026) and diet soft drink (3.78 ± 0.006). The maximum drop in plaque pH was seen with regular soft drink followed by high energy drink and diet soft drink. Regular soft drink possesses a greater acid challenge potential on enamel than diet and high energy soft drinks. However, in this clinical trial, the pH associated with either soft drink did not reach the critical pH which is expected for enamel demineralization and dissolution.

[Mobile-phone e-mail use, social networks, and loneliness among Japanese high school students].

Science.gov (United States)

Ogata, Yasuko; Izumi, Yukiko; Kitaike, Tadashi

2006-07-01

The purposes of this study were to assess the loneliness of Japanese high school students who own and use a mobile phone, to clarify the relationships between students' loneliness and their social network and frequency of use of e-mail feature, and to demonstrate relationships with a student's social network and recognition of the benefits and drawbacks of mobile phone use. The participants were 227 students from two classes in each grade of a high school in the Kanto region of Japan. Participants answered a questionnaire covering the UCLA Loneliness Scale as well as questions pertaining to the circumstances of use of their mobile phones, their social networks (e.g., number of friends), and their perceptions of the benefits and drawbacks of mobile phone use. The questionnaires of students owning a mobile phone were analyzed. Total scores for the UCLA Loneliness Scale were calculated, and factor analysis was performed for the benefits and drawbacks. A total of 220 questionnaires were returned, for which 94.1 percent of respondents owned a mobile phone. The percentages of male and female respondents were 58% and 42%. Chronbach's alpha for the UCLA Loneliness Scale (total score) was 0.87, a result similar to previous studies with high school and university students. Factor analysis revealed five factors associated with the benefits and drawbacks of mobile phone use. Multiple-regression analysis showed that 42.9% of the variance in "frequency of e-mail use" was explained by grade level, frequency of mobile phone use, and two of the five factors from the benefits and drawbacks ("difficulty of communication," and "possible sleep loss due to nighttime e-mailing"). Stepwise multiple-regression analysis revealed that 24.4% of the variance in UCLA Loneliness Score was explained by gender, the frequency of e-mail use, the number of friends and the presence/absence of a girlfriend or boyfriend. Presence of an active social network and frequent e-mailing by mobile phone reduced

Mobility Performance in Slow- and High-Speed LTE Real Scenarios

DEFF Research Database (Denmark)

Gimenez, Lucas Chavarria; Cascino, Maria Carmela; Stefan, Maria

2016-01-01

Mobility performance and handover data interruption times in real scenarios are studied by means of field measurements in an operational LTE network. Both slow- and high-speed scenarios are analyzed by collecting results from two different areas: Aalborg downtown and the highway which encircles...... in the city center as cells on the same site often cover different non-crossing street canyons. Moreover, no handover failures are experienced in the measurements which confirms robust LTE mobility performance. The average interruption time, which is at least equal to the handover execution time, lays within...... the same city. Measurements reveal that the terminal is configured by the network with different handover parametrization depending on the serving cell, which indicates the use of mobility robustness optimization. Although the network is dominated by three sector sites, no intra-site handovers are observed...

Mobility and language change in Denmark

DEFF Research Database (Denmark)

Monka, Malene

featured substantial amounts of dialect features (Kristensen 1980; Pedersen 1986). In 2005 to 2010, researchers at the Danish National Research Center for Language Change in Real Time (LANCHART) and the University of Southern Denmark re-interviewed informants, thus providing data for investigating language......Mobility and language change in Denmark This paper demonstrates how mobility affects language change in real time and reports on the results of my PhD-thesis. In the thesis I made a real time panel study in three towns in distinct dialect areas in Denmark and examined language change in 23 speakers...... recorded in 1978 to 2010. The results emphasize the advantages of approaching mobility from different angles when investigating patterns of language change. The present paper focuses on six geographically and socially mobile informants. At the time of the early recordings, the three towns were in different...

Dependence on the mobile phase pH of the adsorption behavior of propranolol enantiomers on a cellulase protein used as the chiral selector

Energy Technology Data Exchange (ETDEWEB)

Fornstedt, T.; Goetmar, G.; Andersson, M.; Guiochon, G.

1999-02-17

The authors reported previously on the unusual thermodynamic characteristics of the enantioselective interactions between the enantiomers of the {beta}-blocker propranolol and the protein cellobiohydrolase I immobilized on silica. The adsorption of the more retained enantiomer, (S)-propranolol, is endothermic while that of the (R)-propranolol is exothermic. This causes a rapid increase of the selectivity factor with increasing temperature. In this work, the complex dependence of the selectivity factor on the pH of the solvent is studied. They determined the equilibrium isotherms of (R)- and (S)-propranolol in a wide concentration range (0.25 {micro}M to 1.1 mM) at six different mobile-phase pHs (4.7, 5.0, 5.2, 5.5, 5.7, and 6.0) and fitted the data obtained to the bi-Langmuir model. This gave the saturation capacity and the binding constant of the nonselective contribution for the two enantiomers. It also gave these parameters for the enantioselective contributions of each of them. The dependence of these parameters on the pH is discussed and interpreted in terms of the retention mechanism. Conclusions are in excellent agreement with recent, independent results on the structure of the protein obtained by X-ray crystallography.

Filters for mobile radio from high Tc ceramic superconductors

International Nuclear Information System (INIS)

Peterson, G.E.; Wong, E.; Alford, N.McN.

1990-01-01

Mobile radio frequencies lie between 30 MHz and 1,000 MHz. This frequency range is ideal for ceramic high T c superconductors. We have designed Chebyshev, Butterworth and interdigital filters that can employ high T c superconductors in the form of rods, tubes and helices. In general, the performance of these filters at milliwatt power levels is excellent. We will describe fabrication of the superconductors and filter design

High Sensitivity pH Sensor Based on Porous Silicon (PSi Extended Gate Field-Effect Transistor

Directory of Open Access Journals (Sweden)

Naif H. Al-Hardan

2016-06-01

Full Text Available In this study, porous silicon (PSi was prepared and tested as an extended gate field-effect transistor (EGFET for pH sensing. The prepared PSi has pore sizes in the range of 500 to 750 nm with a depth of approximately 42 µm. The results of testing PSi for hydrogen ion sensing in different pH buffer solutions reveal that the PSi has a sensitivity value of 66 mV/pH that is considered a super Nernstian value. The sensor considers stability to be in the pH range of 2 to 12. The hysteresis values of the prepared PSi sensor were approximately 8.2 and 10.5 mV in the low and high pH loop, respectively. The result of this study reveals a promising application of PSi in the field for detecting hydrogen ions in different solutions.

Determination of the coherence length in high-mobility semiconductor-coupled Josephson weak links

International Nuclear Information System (INIS)

Kleinsasser, A.W.

1991-01-01

A Nb-InAs-Nb superconductor-semiconductor-superconductor weak link based on a high-mobility homoepitaxial n-InAs film was reported recently [Akazaki, Kawakami, and Nittu J. Appl. Phys. 66, 6121 (1989)]. Measurements of the electron concentration, effective mass, and mobility allowed the coherence length in the normal link to be calculated. The mobility was high enough that the dirty limit was not applicable in the temperature range (∼2--7 K) over which the device critical current was measured. The temperature dependence of the critical current could not be fit by the usual theoretical form, even though an expression for the coherence length was used that should be applicable in both the clean and dirty limits. In this paper is demonstrated an excellent fit to the data, obtained by using the magnitude of the coherence length as a fitting parameter and assuming the dirty limit temperature dependence. This implies a coherence length proportional to T -1/2 but far shorter than that calculated from the known material parameters. It is suggested that a different scaling length may apply in high-mobility devices

Impaired drug absorption due to high stomach pH: a review of strategies for mitigation of such effect to enable pharmaceutical product development.

Science.gov (United States)

Mitra, Amitava; Kesisoglou, Filippos

2013-11-04

Published reports have clearly shown that weakly basic drugs which have low solubility at high pH could have impaired absorption in patients with high gastric pH thus leading to reduced and variable bioavailability. Since such reduction in exposure can lead to significant loss of efficacy, it is imperative to (1) understand the behavior of the compound as a function of stomach pH to inform of any risk of bioavailability loss in clinical studies and (2) develop a robust formulation which can provide adequate exposure in achlorhydric patients. In this review paper, we provide an overview of the factors that can cause high gastric pH in human, discuss clinical and preclinical pharmacokinetic data for weak bases under conditions of normal and high gastric pH, and give examples of formulation strategies to minimize or mitigate the reduced absorption of weakly basic drugs under high gastric pH conditions. It should be noted that the ability to overcome pH sensitivity issues is highly compound dependent and there are no obvious and general solutions to overcome such effect. Further, we discuss, along with several examples, the use of biopharmaceutical tools such as in vitro dissolution, absorption modeling, and gastric pH modified animal models to assess absorption risk of weak bases in high gastric pH and also the use of these tools to enable development of formulations to mitigate such effects.

fraud detection in mobile communications networks using user

African Journals Online (AJOL)

DEPT OF AGRICULTURAL ENGINEERING

Fraud detection is an important application, since network operators lose a relevant portion of their revenue to fraud. ... testing the methods with data from real mobile communications networks. Keywords: Call data, fraud ...... Ph. D. thesis. Pur-.

Random demographic household surveys in highly mobile pastoral communities in Chad

Science.gov (United States)

Béchir, Mahamat; Hattendorf, Jan; Bonfoh, Bassirou; Zinsstag, Jakob; Schelling, Esther

2011-01-01

Abstract Problem Reliable demographic data is a central requirement for health planning and management, and for the implementation of adequate interventions. This study addresses the lack of demographic data on mobile pastoral communities in the Sahel. Approach A total of 1081 Arab, Fulani and Gorane women and 2541 children (1336 boys and 1205 girls) were interviewed and registered by a biometric fingerprint scanner in five repeated random transect demographic and health surveys conducted from March 2007 to January 2008 in the Lake Chad region in Chad. Local setting Important determinants for the planning and implementation of household surveys among mobile pastoral communities include: environmental factors; availability of women for interviews; difficulties in defining “own” children; the need for information-education-communication campaigns; and informed consent of husbands in typically patriarchal societies. Relevant changes Due to their high mobility, only 5% (56/1081) of registered women were encountered twice. Therefore, it was not possible to establish a demographic and health cohort. Lessons learnt Prospective demographic and health cohorts are the most accurate method to assess child mortality and other demographic indices. However, their feasibility in a highly mobile pastoral setting remains to be shown. Future interdisciplinary scientific efforts need to target innovative methods, tools and approaches to include marginalized communities in operational health and demographic surveillance systems. PMID:21556307

High-mobility ultrathin semiconducting films prepared by spin coating

Science.gov (United States)

Mitzi, David B.; Kosbar, Laura L.; Murray, Conal E.; Copel, Matthew; Afzali, Ali

2004-03-01

The ability to deposit and tailor reliable semiconducting films (with a particular recent emphasis on ultrathin systems) is indispensable for contemporary solid-state electronics. The search for thin-film semiconductors that provide simultaneously high carrier mobility and convenient solution-based deposition is also an important research direction, with the resulting expectations of new technologies (such as flexible or wearable computers, large-area high-resolution displays and electronic paper) and lower-cost device fabrication. Here we demonstrate a technique for spin coating ultrathin (~50Å), crystalline and continuous metal chalcogenide films, based on the low-temperature decomposition of highly soluble hydrazinium precursors. We fabricate thin-film field-effect transistors (TFTs) based on semiconducting SnS2-xSex films, which exhibit n-type transport, large current densities (>105Acm-2) and mobilities greater than 10cm2V-1s-1-an order of magnitude higher than previously reported values for spin-coated semiconductors. The spin-coating technique is expected to be applicable to a range of metal chalcogenides, particularly those based on main group metals, as well as for the fabrication of a variety of thin-film-based devices (for example, solar cells, thermoelectrics and memory devices).

Effects of Iodide and Hydrogen Peroxide on Measuring High Temperature pH in Various Lithium Borate Buffer Solutions

Energy Technology Data Exchange (ETDEWEB)

Hwang, Jae Sik; Yun, Myung Hee; Yeon, Jei Won; Song, Kyu Seok [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2008-10-15

In a reactor coolant system of nuclear power plants, the need for reliable high temperature pH electrodes has resulted from interests in the corrosion and corrosion product behaviors of the structural materials in a high temperature coolant system. In developing the electrodes for measuring the high temperature pH of aqueous solutions, it is necessary to note two major problems: the chemical stability of an electrode against other chemical impurities, and an electrode's integrity as the temperature and pressure are varied between operational extremes. Over the past decade Macdonald et al. and Danielson et al. have developed many ceramic membrane pH electrodes based on a yttrium stabilized zirconium oxide. However, there are still many experimental difficulties associated with the problems in obtaining electrochemical information across different pressure boundaries and against many kinds of chemical impurities caused by the radiolysis of water and the leakage of a fuel clad. In the present work, we investigated the effects of the environmental factors on a high temperature pH. The selected environmental factors are as follows: system pressure, and chemical species such as iodide and hydrogen peroxide ions.

Diurnal variation in ruminal pH on the digestibility of highly digestible perennial ryegrass during continuous culture fermentation.

Science.gov (United States)

Wales, W J; Kolver, E S; Thorne, P L; Egan, A R

2004-06-01

Dairy cows grazing high-digestibility pastures exhibit pronounced diurnal variation in ruminal pH, with pH being below values considered optimal for digestion. Using a dual-flow continuous culture system, the hypothesis that minimizing diurnal variation in pH would improve digestion of pasture when pH was low, but not at a higher pH, was tested. Four treatments were imposed, with pH either allowed to exhibit normal diurnal variation around an average pH of 6.1 or 5.6, or maintained at constant pH. Digesta samples were collected during the last 3 d of each of four, 9-d experimental periods. A constant pH at 5.6 compared with a constant pH of 6.1 reduced the digestibility of organic matter (OM), neutral detergent (NDF), and acid detergent fiber (ADF) by 7, 14, and 21%, respectively. When pH was allowed to vary (averaging 5.6), digestion of OM, NDF, and ADF were reduced by 15,30, and 36%, respectively, compared with pH varying at 6.1. There was little difference in digestion parameters when pH was either constant or varied with an average pH of 6.1. However, when average pH was 5.6, maintaining a constant pH significantly increased digestion of OM, NDF, and ADF by 5, 25, and 24% compared with a pH that exhibited normal diurnal variation. These in vitro results show that gains in digestibility and potential milk production can be made by minimizing diurnal variation in ruminal pH, but only when ruminal pH is low (5.6). However, larger gains in productivity can be achieved by increasing average daily ruminal pH from 5.6 to 6.1.

Electronic characteristics of p-type transparent SnO monolayer with high carrier mobility

International Nuclear Information System (INIS)

Du, Juan; Xia, Congxin; Liu, Yaming; Li, Xueping; Peng, Yuting; Wei, Shuyi

2017-01-01

Graphical abstract: SnO monolayer is a p-type transparent semiconducting oxide with high hole mobility (∼641 cm 2 V −1 s −1 ), which is much higher than that of MoS 2 monolayer, which indicate that it can be a promising candidate for high-performance nanoelectronic devices. Display Omitted - Highlights: • SnO monolayer is a p-type transparent semiconducting oxide. • The transparent properties can be still maintained under the strain 8%. • It has a high hole mobility (∼641 cm 2 V −1 s −1 ), which is higher than that of MoS 2 monolayer. - Abstract: More recently, two-dimensional (2D) SnO nanosheets are attaching great attention due to its excellent carrier mobility and transparent characteristics. Here, the stability, electronic structures and carrier mobility of SnO monolayer are investigated by using first-principles calculations. The calculations of the phonon dispersion spectra indicate that SnO monolayer is dynamically stable. Moreover, the band gap values are decreased from 3.93 eV to 2.75 eV when the tensile strain is applied from 0% to 12%. Interestingly, SnO monolayer is a p-type transparent semiconducting oxide with hole mobility of 641 cm 2 V −1 s −1 , which is much higher than that of MoS 2 monolayer. These findings make SnO monolayer becomes a promising 2D material for applications in nanoelectronic devices.

Influence of pH on dynamics of microbial enhanced oil recovery processes using biosurfactant producing Pseudomonas putida: Mathematical modelling and numerical simulation.

Science.gov (United States)

Sivasankar, P; Suresh Kumar, G

2017-01-01

In present work, the influence of reservoir pH conditions on dynamics of microbial enhanced oil recovery (MEOR) processes using Pseudomonas putida was analysed numerically from the developed mathematical model for MEOR processes. Further, a new strategy to improve the MEOR performance has also been proposed. It is concluded from present study that by reversing the reservoir pH from highly acidic to low alkaline condition (pH 5-8), flow and mobility of displaced oil, displacement efficiency, and original oil in place (OOIP) recovered gets significantly enhanced, resulting from improved interfacial tension (IFT) reduction by biosurfactants. At pH 8, maximum of 26.1% of OOIP was recovered with higher displacement efficiency. The present study introduces a new strategy to increase the recovery efficiency of MEOR technique by characterizing the biosurfactants for IFT min /IFT max values for different pH conditions and subsequently, reversing the reservoir pH conditions at which the IFT min /IFT max value is minimum. Copyright © 2016 Elsevier Ltd. All rights reserved.

High-resolution charge carrier mobility mapping of heterogeneous organic semiconductors

Science.gov (United States)

Button, Steven W.; Mativetsky, Jeffrey M.

2017-08-01

Organic electronic device performance is contingent on charge transport across a heterogeneous landscape of structural features. Methods are therefore needed to unravel the effects of local structure on overall electrical performance. Using conductive atomic force microscopy, we construct high-resolution out-of-plane hole mobility maps from arrays of 5000 to 16 000 current-voltage curves. To demonstrate the efficacy of this non-invasive approach for quantifying and mapping local differences in electrical performance due to structural heterogeneities, we investigate two thin film test systems, one bearing a heterogeneous crystal structure [solvent vapor annealed 5,11-Bis(triethylsilylethynyl)anthradithiophene (TES-ADT)—a small molecule organic semiconductor] and one bearing a heterogeneous chemical composition [p-DTS(FBTTh2)2:PC71BM—a high-performance organic photovoltaic active layer]. TES-ADT shows nearly an order of magnitude difference in hole mobility between semicrystalline and crystalline areas, along with a distinct boundary between the two regions, while p-DTS(FBTTh2)2:PC71BM exhibits subtle local variations in hole mobility and a nanoscale domain structure with features below 10 nm in size. We also demonstrate mapping of the built-in potential, which plays a significant role in organic light emitting diode and organic solar cell operation.

Estimation of Hydrazine Decomposition on Measuring the High-Temperature pH in Hydrazine/ETA Solutions at 553 K

International Nuclear Information System (INIS)

Hwang, Jae Sik; Yeon, Jei Won; Yun, Myung Hee; Song, Kyu Seok; Lee, Sang Ill

2010-01-01

Hydrazine is one of the most excellent oxygen scavengers used in the secondary circuit of nuclear power plants. Furthermore, in some pants, the hydrazine is used as a source of hydrogen required to suppress radiolysis of the coolant water in the primary loop. When hydrazine was exposed in the high temperature and high pressure water, it can be decomposed into the various products such as NH 3 , N 2 , H 2 , and NO 3 ions. As the result, the pH of solution containing hydrazine in the condition of the high temperature and high pressure can be changed by those decomposed products. In the present work, we investigated the decomposition behavior of hydrazine in ETA (ethanol amine) solution. In addition, we measured the high temperature pH at 553 K on the various hydrazine/ETA solutions for confirming the applicability of the yttria stabilized zirconia (YSZ)- based pH electrode in secondary circuit of the nuclear power plants

Following the Dynamics of pH in Endosomes of Live Cells with SERS Nanosensors

DEFF Research Database (Denmark)

Kneipp, J.; Kneipp, Harald; Wittig, B.

2010-01-01

The surface enhanced Raman scattering (SERS) spectrum of a reporter molecule attached to gold or silver nanostructures, which is pH-sensitive, can deliver information on the local pH in the environment of the nanostructure. Here, we demonstrate the use of a mobile SERS nanosensor made from gold...... nanaoaggregates and 4-mercaptobenzoic acid (pMBA) attached as a reporter for monitoring changes in local pH of the cellular compartments of living NIH/3T3 cells. We show that SERS nanosensors enable the dynamics of local pH in individual live cells to be followed at subendosomal resolution in a timeline...

A Dual-Mode Large-Arrayed CMOS ISFET Sensor for Accurate and High-Throughput pH Sensing in Biomedical Diagnosis.

Science.gov (United States)

Huang, Xiwei; Yu, Hao; Liu, Xu; Jiang, Yu; Yan, Mei; Wu, Dongping

2015-09-01

The existing ISFET-based DNA sequencing detects hydrogen ions released during the polymerization of DNA strands on microbeads, which are scattered into microwell array above the ISFET sensor with unknown distribution. However, false pH detection happens at empty microwells due to crosstalk from neighboring microbeads. In this paper, a dual-mode CMOS ISFET sensor is proposed to have accurate pH detection toward DNA sequencing. Dual-mode sensing, optical and chemical modes, is realized by integrating a CMOS image sensor (CIS) with ISFET pH sensor, and is fabricated in a standard 0.18-μm CIS process. With accurate determination of microbead physical locations with CIS pixel by contact imaging, the dual-mode sensor can correlate local pH for one DNA slice at one location-determined microbead, which can result in improved pH detection accuracy. Moreover, toward a high-throughput DNA sequencing, a correlated-double-sampling readout that supports large array for both modes is deployed to reduce pixel-to-pixel nonuniformity such as threshold voltage mismatch. The proposed CMOS dual-mode sensor is experimentally examined to show a well correlated pH map and optical image for microbeads with a pH sensitivity of 26.2 mV/pH, a fixed pattern noise (FPN) reduction from 4% to 0.3%, and a readout speed of 1200 frames/s. A dual-mode CMOS ISFET sensor with suppressed FPN for accurate large-arrayed pH sensing is proposed and demonstrated with state-of-the-art measured results toward accurate and high-throughput DNA sequencing. The developed dual-mode CMOS ISFET sensor has great potential for future personal genome diagnostics with high accuracy and low cost.

Enhanced mobility in vertically scaled N-polar high-electron-mobility transistors using GaN/InGaN composite channels

Science.gov (United States)

Li, Haoran; Wienecke, Steven; Romanczyk, Brian; Ahmadi, Elaheh; Guidry, Matthew; Zheng, Xun; Keller, Stacia; Mishra, Umesh K.

2018-02-01

A GaN/InGaN composite channel design for vertically scaled N-polar high-electron-mobility transistor (HEMT) structures is proposed and demonstrated by metal-organic chemical vapor deposition. In a conventional N-polar HEMT structure, as the channel thickness (tch) decreases, the sheet charge density (ns) decreases, the electric field in the channel increases, and the centroid of the two-dimensional electron gas (2DEG) moves towards the back-barrier/channel interface, resulting in stronger scattering and lower electron mobility (μ). In this study, a thin InGaN layer was introduced in-between the channel and the AlGaN cap to increase the 2DEG density and reduce the electric field in the channel and therefore increase the electron mobility. The dependence of μ on the InGaN thickness (tInGaN) and the indium composition (xIn) was investigated for different channel thicknesses. With optimized tInGaN and xIn, significant improvements in electron mobility were observed. For a 6 nm channel HEMT structure, the electron mobility increased from 606 to 1141 cm2/(V.s) when the 6 nm thick pure GaN channel was replaced by the 4 nm GaN/2 nm In0.1Ga0.9N composite channel.

Comprehensive review on the development of high mobility in oxide thin film transistors

Science.gov (United States)

Choi, Jun Young; Lee, Sang Yeol

2017-11-01

Oxide materials are one of the most advanced key technology in the thin film transistors (TFTs) for the high-end of device applications. Amorphous oxide semiconductors (AOSs) have leading technique for flat panel display (FPD), active matrix organic light emitting display (AMOLED) and active matrix liquid crystal display (AMLCD) due to their excellent electrical characteristics, such as field effect mobility ( μ FE ), subthreshold swing (S.S) and threshold voltage ( V th ). Covalent semiconductor like amorphous silicon (a-Si) is attributed to the anti-bonding and bonding states of Si hybridized orbitals. However, AOSs have not grain boundary and excellent performances originated from the unique characteristics of AOS which is the direct orbital overlap between s orbitals of neighboring metal cations. High mobility oxide TFTs have gained attractive attention during the last few years and today in display industries. It is progressively developed to increase the mobility either by exploring various oxide semiconductors or by adopting new TFT structures. Mobility of oxide thin film transistor has been rapidly increased from single digit to higher than 100 cm2/V·s in a decade. In this review, we discuss on the comprehensive review on the mobility of oxide TFTs in a decade and propose bandgap engineering and novel structure to enhance the electrical characteristics of oxide TFTs.

Evaluating high pH for control of dreissenid mussels

OpenAIRE

Dave Evans; Sergey E. Mastitsky; Katherine L. Prescott; Thomas H. Prescott; Renata Claudi; Anna Carolina Taraborelli

2013-01-01

Two field experiments were carried out using a custom built flow-through laboratory to test the effect of elevated pH on dreissenid musselsas a potential control method. Both experiments tested the ability of dreissenid pediveligers to settle under conditions of elevated pH and thelong-term survival of adult dreissenids under the same conditions. The two experimental sites had different water quality and differentspecies of dreissenids present. The settlement of quagga mussel pediveligers at ...

pH sensor calibration procedure

OpenAIRE

Artero Delgado, Carola; Nogueras Cervera, Marc; Manuel Lázaro, Antonio; Prat Tasias, Jordi; Prat Farran, Joana d'Arc

2013-01-01

This paper describes the calibration of pH sensor located at the OBSEA marine Observatory. This instrument is based on an industrial pH electrode that is connected to a CTD instrument (Conductivity, Temperature, and Depth ). The calibration of the pH sensor has been done using a high precision spectrophotometer pH meter from Institute of Marine Sciences (ICM), and in this way it has been obtained a numerical function for the p H sensor propor...

On the problem of silica solubility at high pH

International Nuclear Information System (INIS)

Eikenberg, J.

1990-07-01

The aqueous system Na 2 O-H 2 O-SiO 2 is considered to play an important role when strong alkaline pore waters of a cement based intermediate level radioactive waste repository intrude into the rock formations surrounding the near field. Under such conditions unknown quantities of silica may dissolve. Therefore the pH-dependence of the solubility of amorphous silica and quartz is investigated by a parameter variation study using the geochemical speciation code MINEQL/EIR. Published silica solubility data obtained in sodium hydroxide solutions at 25 and 90 o C are compared with the results of four models which use different proposed values of the rather uncertain equilibrium constants. Of main interest is the question of whether, in a high pH region, the silica solubility can be explained with different monomeric species only, or to what extent additional polymeric silica species have to be considered as well. The solubility of amorphous silica at 25 o C is well understood up to a pH of about 10.5, where it is determined by the solubility product and the first dissociation constant of monomeric silic acid. The most probable cause of the increased solubility of amorphous silica in the region between pH 10.5 and 11.3 is the formation of dimers, trimers and tetramers. Below a total silica concentration of 0.001 M and pH ≤ 10.0, however, polymerisation proves to be insignificant. Besides low temperature studies using amorphous silica, the solubility of quartz has also been measured in NaOH solutions at 90 o C. As is the case at lower temperatures, the reported values for the second dissociation constant at 90 o C scatter widely. It can be shown that in a NaOH medium up to 0.1 M only mononuclear silica species are stable. Therefore it is concluded that the trend of monomers to form polymers decreases strongly with temperature. In strong NaOH solutions at elevated temperatures, silica-sodium ion pairing seems to gain importance. (author) 12 figs., 9 tabs., 65 refs

PH Sensitive Polymers for Improving Reservoir Sweep and Conformance Control in Chemical Flooring

Energy Technology Data Exchange (ETDEWEB)

Mukul Sharma; Steven Bryant; Chun Huh

2008-03-31

There is an increasing opportunity to recover bypassed oil from depleted, mature oilfields in the US. The recovery factor in many reservoirs is low due to inefficient displacement of the oil by injected fluids (typically water). The use of chemical flooding methods to increase recovery efficiencies is severely constrained by the inability of the injected chemicals to contact the bypassed oil. Low sweep efficiencies are the primary cause of low oil recoveries observed in the field in chemical flooding operations even when lab studies indicate high oil recovery efficiency. Any technology that increases the ability of chemical flooding agents to better contact the remaining oil and reduce the amount of water produced in conjunction with the produced oil will have a significant impact on the cost of producing oil domestically in the US. This translates directly into additional economically recoverable reserves, which extends the economic lives of marginal and mature wells. The objective of this research project was to develop a low-cost, pH-triggered polymer for use in IOR processes to improve reservoir sweep efficiency and reservoir conformance in chemical flooding. Rheological measurements made on the polymer solution, clearly show that it has a low viscosity at low pH and exhibits a sudden increase in viscosity (by 2 orders of magnitude or more) at a pH of 3.5 to 4. This implies that the polymer would preferentially flow into zones containing water since the effective permeability to water is highest in these zones. As the pH of the zone increases due to the buffering capacity of the reservoir rock, the polymer solution undergoes a liquid to gel transition causing a sharp increase in the viscosity of the polymer solution in these zones. This allows operationally robust, in-depth conformance treatment of such water bearing zones and better mobility control. The rheological properties of HPAM solutions were measured. These include: steady-shear viscosity and

Sows with high milk production had both a high feed intake and high body mobilization

DEFF Research Database (Denmark)

Strathe, A. V.; Bruun, T. S.; Hansen, C. F.

2017-01-01

Selection for increased litter size have generated hyper-prolific sows that nurses large litters, however limited knowledge is available regarding the connection between milk production, feed intake and body mobilization of these modern sows. The aim of the current study was to determine what...... be explained by a relatively higher proportion of their body reserves being mobilized compared with multiparous sows. The ADG of the litter was positively related by ADFI of the sows, litter size and BW loss and increasing the ADFI with 1 kg/day throughout lactation likely increased the ADG of the litter...... characterized sows with high milk production and nursing large litters, differences between sows of different parities and effects of lactational performance on next reproductive cycle. In total 565 sows (parity 1 to 4) were studied from 7 days before farrowing until weaning. On day 2 postpartum litters were...

Mobility of persons who are blind: How the attentional processes and working memory are involved?

OpenAIRE

PIGEON, Caroline; MARIN-LAMELLET, Claude

2015-01-01

Although navigation without vision seems to strongly mobilize the attentional processes and the working memory, few studies seem to be conducted about the link between these processes and the mobility of people who are blind. The main aim of this PhD work is to consider the attentional and working memory capacities of people who are blind and investigate the attentional processes involved during the navigation activity. In the first part of this PhD work, blind participants (early and late) p...

Very high channel conductivity in low-defect AlN/GaN high electron mobility transistor structures

International Nuclear Information System (INIS)

Dabiran, A. M.; Wowchak, A. M.; Osinsky, A.; Xie, J.; Hertog, B.; Cui, B.; Chow, P. P.; Look, D. C.

2008-01-01

Low defect AlN/GaN high electron mobility transistor (HEMT) structures, with very high values of electron mobility (>1800 cm 2 /V s) and sheet charge density (>3x10 13 cm -2 ), were grown by rf plasma-assisted molecular beam epitaxy (MBE) on sapphire and SiC, resulting in sheet resistivity values down to ∼100 Ω/□ at room temperature. Fabricated 1.2 μm gate devices showed excellent current-voltage characteristics, including a zero gate saturation current density of ∼1.3 A/mm and a peak transconductance of ∼260 mS/mm. Here, an all MBE growth of optimized AlN/GaN HEMT structures plus the results of thin-film characterizations and device measurements are presented

Ion mobility based on column leaching of South African gold tailings dam with chemometric evaluation.

Science.gov (United States)

Cukrowska, Ewa M; Govender, Koovila; Viljoen, Morris

2004-07-01

New column leaching experiments were designed and used as an alternative rapid screening approach to element mobility assessment. In these experiments, field-moist material was treated with an extracting solution to assess the effects of acidification on element mobility in mine tailings. The main advantage of this version of column leaching experiments with partitioned segments is that they give quick information on current element mobility in conditions closely simulating field conditions to compare with common unrepresentative air-dried, sieved samples used for column leaching experiments. Layers from the tailings dump material were sampled and packed into columns. The design of columns allows extracting leachates from each layer. The extracting solutions used were natural (pH 6.8) and acidified (pH 4.2) rainwater. Metals and anions were determined in the leachates. The concentrations of metals (Ca, Mg, Fe, Mn, Al, Cr, Ni, Co, Zn, and Cu) in sample leachates were determined using ICP OES. The most important anions (NO3-, Cl-, and SO4(2)-) were determined using the closed system izotacophoresis ITP analyser. The chemical analytical data from tailings leaching and physico-chemical data from field measurements (including pH, conductivity, redox potential, temperature) were used for chemometric evaluation of element mobility. Principal factor analysis (PFA) was used to evaluate ions mobility from different layers of tailings dump arising from varied pH and redox conditions. It was found that the results from the partitioned column leaching illustrate much better complex processes of metals mobility from tailings dump than the total column. The chemometric data analysis (PFA) proofed the differences in the various layers leachability that are arising from physico-chemical processes due to chemical composition of tailings dump deposit. Copyright 2004 Elsevier Ltd.

Electronic characteristics of p-type transparent SnO monolayer with high carrier mobility

Energy Technology Data Exchange (ETDEWEB)

Du, Juan [College of Physics and Materials Science, Henan Normal University, Xinxiang, Henan 453007 (China); Xia, Congxin, E-mail: xiacongxin@htu.edu.cn [College of Physics and Materials Science, Henan Normal University, Xinxiang, Henan 453007 (China); Liu, Yaming [Henan Institute of Science and Technology, Xinxiang 453003 (China); Li, Xueping [College of Physics and Materials Science, Henan Normal University, Xinxiang, Henan 453007 (China); Peng, Yuting [Department of Physics, University of Texas at Arlington, TX 76019 (United States); Wei, Shuyi [College of Physics and Materials Science, Henan Normal University, Xinxiang, Henan 453007 (China)

2017-04-15

Graphical abstract: SnO monolayer is a p-type transparent semiconducting oxide with high hole mobility (∼641 cm{sup 2} V{sup −1} s{sup −1}), which is much higher than that of MoS{sub 2} monolayer, which indicate that it can be a promising candidate for high-performance nanoelectronic devices. Display Omitted - Highlights: • SnO monolayer is a p-type transparent semiconducting oxide. • The transparent properties can be still maintained under the strain 8%. • It has a high hole mobility (∼641 cm{sup 2} V{sup −1} s{sup −1}), which is higher than that of MoS{sub 2} monolayer. - Abstract: More recently, two-dimensional (2D) SnO nanosheets are attaching great attention due to its excellent carrier mobility and transparent characteristics. Here, the stability, electronic structures and carrier mobility of SnO monolayer are investigated by using first-principles calculations. The calculations of the phonon dispersion spectra indicate that SnO monolayer is dynamically stable. Moreover, the band gap values are decreased from 3.93 eV to 2.75 eV when the tensile strain is applied from 0% to 12%. Interestingly, SnO monolayer is a p-type transparent semiconducting oxide with hole mobility of 641 cm{sup 2} V{sup −1} s{sup −1}, which is much higher than that of MoS{sub 2} monolayer. These findings make SnO monolayer becomes a promising 2D material for applications in nanoelectronic devices.

A possible high-mobility signal in bulk MoTe2: Temperature independent weak phonon decay

Directory of Open Access Journals (Sweden)

Titao Li

2016-11-01

Full Text Available Layered transition metal dichalcogenides (TMDs have attracted great attention due to their non-zero bandgap for potential application in high carrier mobility devices. Recent studies demonstrate that the carrier mobility of MoTe2 would decrease by orders of magnitude when used for few-layer transistors. As phonon scattering has a significant influence on carrier mobility of layered material, here, we first reported temperature-dependent Raman spectra of bulk 2H-MoTe2 from 80 to 300 K and discovered that the phonon lifetime of both E12g and A1g vibration modes are independent with temperature. These results were explained by the weak phonon decay in MoTe2. Our results imply the existence of a carrier mobility higher than the theoretical value in intrinsic bulk 2H-MoTe2 and the feasibility to obtain MoTe2-based transistors with sufficiently high carrier mobility.

Effects of cyanobacterial-driven pH increases on sediment nutrient fluxes and coupled nitrification-denitrification in a shallow fresh water estuary

Directory of Open Access Journals (Sweden)

Y. Gao

2012-07-01

Full Text Available Summer cyanobacterial blooms caused an elevation in pH (9 to ~10.5 that lasted for weeks in the shallow and tidal-fresh region of the Sassafras River, a tributary of Chesapeake Bay (USA. Elevated pH promoted desorption of sedimentary inorganic phosphorus and facilitated conversion of ammonium (NH₄⁺ to ammonia (NH₃. In this study, we investigated pH effects on exchangeable NH₄⁺ desorption, pore water diffusion and the flux rates of NH₄⁺, soluble reactive phosphorus (SRP and nitrate (NO₃⁻, nitrification, denitrification, and oxygen consumption. Elevated pH enhanced desorption of exchangeable NH₄⁺ through NH₃ formation from both pore water and adsorbed NH₄⁺ pools. Progressive penetration of high pH from the overlying water into sediment promoted the mobility of SRP and the release of total ammonium (NH₄⁺ and NH₃ into the pore water. At elevated pH levels, high sediment-water effluxes of SRP and total ammonium were associated with reduction of nitrification, denitrification and oxygen consumption rates. Alkaline pH and the toxicity of NH₃ may inhibit nitrification in the thin aerobic zone, simultaneously constraining coupled nitrification–denitrification with limited NO₃⁻ supply and high pH penetration into the anaerobic zone. Geochemical feedbacks to pH elevation, such as enhancement of dissolved nutrient effluxes and reduction in N₂ loss via denitrification, may enhance the persistence of cyanobacterial blooms in shallow water ecosystems.

Effects of phytoextraction on heavy metal concentrations and pH of pore-water of biosolids determined using an in situ sampling technique

Energy Technology Data Exchange (ETDEWEB)

Huynh, T.T. [Applied Ecology Research Group, School of Botany, University of Melbourne, Parkville, VIC 3010 (Australia)], E-mail: t.huynh11@pgrad.unimelb.edu.au; Laidlaw, W.S. [Applied Ecology Research Group, School of Botany, University of Melbourne, Parkville, VIC 3010 (Australia); Singh, B. [Faculty of Agriculture, Food and Natural Resources, University of Sydney, Sydney, NSW 2006 (Australia); Gregory, D. [Research and Technology Division, Melbourne Water, Melbourne, VIC 3001 (Australia); Baker, A.J.M. [Applied Ecology Research Group, School of Botany, University of Melbourne, Parkville, VIC 3010 (Australia)

2008-12-15

Heavy metal concentrations and pH of pore-water in contaminated substrates are important factors in controlling metal uptake by plants. We investigated the effects of phytoextraction on these properties in the solution phase of biosolids and diluted biosolids in a 12-month phytoextraction column experiment. Phytoextraction using Salix and Populus spp. temporarily decreased pore-water pH of the substrates over the experimental period followed by a return to initial pH conditions. Salix x reichardtii and Populus balsamifera effectively extracted Ni, Zn and Cd and actively mobilized these metals from the solid to the solution phase. S. x reichardtii had the stronger effect on mobilization of metals due to its larger root system. Phytoextraction did not affect Cu in the solution phase of the biosolids. Heavy metals were leached down to lower depths of the columns during the phytoextraction process. - Salix x reichardtii and Populus balsamifera extracted Ni, Zn and Cd and mobilized these metals in biosolids during phytoextraction.

Effects of phytoextraction on heavy metal concentrations and pH of pore-water of biosolids determined using an in situ sampling technique

International Nuclear Information System (INIS)

Huynh, T.T.; Laidlaw, W.S.; Singh, B.; Gregory, D.; Baker, A.J.M.

2008-01-01

Heavy metal concentrations and pH of pore-water in contaminated substrates are important factors in controlling metal uptake by plants. We investigated the effects of phytoextraction on these properties in the solution phase of biosolids and diluted biosolids in a 12-month phytoextraction column experiment. Phytoextraction using Salix and Populus spp. temporarily decreased pore-water pH of the substrates over the experimental period followed by a return to initial pH conditions. Salix x reichardtii and Populus balsamifera effectively extracted Ni, Zn and Cd and actively mobilized these metals from the solid to the solution phase. S. x reichardtii had the stronger effect on mobilization of metals due to its larger root system. Phytoextraction did not affect Cu in the solution phase of the biosolids. Heavy metals were leached down to lower depths of the columns during the phytoextraction process. - Salix x reichardtii and Populus balsamifera extracted Ni, Zn and Cd and mobilized these metals in biosolids during phytoextraction

High-mobility ultrathin semiconducting films prepared by spin coating.

Science.gov (United States)

Mitzi, David B; Kosbar, Laura L; Murray, Conal E; Copel, Matthew; Afzali, Ali

2004-03-18

The ability to deposit and tailor reliable semiconducting films (with a particular recent emphasis on ultrathin systems) is indispensable for contemporary solid-state electronics. The search for thin-film semiconductors that provide simultaneously high carrier mobility and convenient solution-based deposition is also an important research direction, with the resulting expectations of new technologies (such as flexible or wearable computers, large-area high-resolution displays and electronic paper) and lower-cost device fabrication. Here we demonstrate a technique for spin coating ultrathin (approximately 50 A), crystalline and continuous metal chalcogenide films, based on the low-temperature decomposition of highly soluble hydrazinium precursors. We fabricate thin-film field-effect transistors (TFTs) based on semiconducting SnS(2-x)Se(x) films, which exhibit n-type transport, large current densities (>10(5) A cm(-2)) and mobilities greater than 10 cm2 V(-1) s(-1)--an order of magnitude higher than previously reported values for spin-coated semiconductors. The spin-coating technique is expected to be applicable to a range of metal chalcogenides, particularly those based on main group metals, as well as for the fabrication of a variety of thin-film-based devices (for example, solar cells, thermoelectrics and memory devices).

Transparent, high mobility InGaZnO thin films deposited by PLD

International Nuclear Information System (INIS)

Suresh, Arun; Gollakota, Praveen; Wellenius, Patrick; Dhawan, Anuj; Muth, John F.

2008-01-01

Transparent oxide semiconductor, InGaZnO, thin films were prepared by pulsed laser deposition at room temperature. The carrier concentration was found to vary by several orders of magnitude from insulating to 10 19 carriers/cm 3 depending on the oxygen partial pressure during deposition. Hall mobilities as high as 16 cm 2 /V s were observed. This is approximately an order of magnitude higher than the mobility of amorphous silicon and indicates that InGaO 3 (ZnO) x with x ≤ 5 may be suitable for transparent, thin film transistor applications. Post-deposition annealing was found to strongly influence the carrier concentration while annealing effects on the electron mobility was less influential

Comparison of fixed-bearing and mobile-bearing total knee arthroplasty after high tibial osteotomy.

Science.gov (United States)

Hernigou, Philippe; Huys, Maxime; Pariat, Jacques; Roubineau, François; Flouzat Lachaniette, Charles Henri; Dubory, Arnaud

2018-02-01

There is no information comparing the results of fixed-bearing total knee replacement and mobile-bearing total knee replacement in the same patients previously treated by high tibial osteotomy. The purpose was therefore to compare fixed-bearing and mobile-bearing total knee replacements in patients treated with previous high tibial osteotomy. We compared the results of 57 patients with osteoarthritis who had received a fixed-bearing prosthesis after high tibial osteotomy with the results of 41 matched patients who had received a rotating platform after high tibial osteotomy. The match was made for length of follow-up period. The mean follow-up was 17 years (range, 15-20 years). The patients were assessed clinically and radiographically. The pre-operative knee scores had no statistically significant differences between the two groups. So was the case with the intra-operative releases, blood loss, thromboembolic complications and infection rates in either group. There was significant improvement in both groups of knees, and no significant difference was observed between the groups (i.e., fixed-bearing and mobile-bearing knees) for the mean Knee Society knee clinical score (95 and 92 points, respectively), or the Knee Society knee functional score (82 and 83 points, respectively) at the latest follow-up. However, the mean post-operative knee motion was higher for the fixed-bearing group (117° versus 110°). In the fixed-bearing group, one knee was revised because of periprosthetic fracture. In the rotating platform mobile-bearing group, one knee was revised because of aseptic loosening of the tibial component. The Kaplan-Meier survivorship for revision at ten years of follow-up was 95.2% for the fixed bearing prosthesis and 91.1% for the rotating platform mobile-bearing prosthesis. Although we did manage to detect significant differences mainly in clinical and radiographic results between the two groups, we found no superiority or inferiority of the mobile

High mobility polymer gated organic field effect transistor using zinc ...

Indian Academy of Sciences (India)

Organic thin film transistors were fabricated using evaporated zinc phthalocyanine as the active layer. Parylene film ... At room temperature, these transistors exhibit p-type conductivity with field-effect ... Keywords. Organic semiconductor; field effect transistor; phthalocyanine; high mobility. ... The evaporation rate was kept at ...

Effects of starvation on the transport of Escherichia coli K12 in saturated porous media are dependent on pH and ionic strength

Science.gov (United States)

Xu, S.; Walczak, J. J.; Wang, L.; Bardy, S. L.; Li, J.

2010-12-01

In this research, we investigate the effects of starvation on the transport of E. coli K12 in saturated porous media. Particularly, we examine the relationship between such effects and the pH and ionic strength of the electrolyte solutions that were used to suspend bacterial cells. E. coli K12 (ATCC 10798) cells were cultured using either Luria-Bertani Miller (LB-Miller) broth (10 g trypton, 5 g yeast extract and 10 g NaCl in 1 L of deionized water) or LB-Luria broth (10 g tryptone, 5 g yeast extract and 0.5 g NaCl in 1 L of deionized water). Both broths had similar pH (~7.1) but differed in ionic strength (LB-Miller: ~170 mM, LB-Luria: ~ 8 mM). The bacterial cells were then harvested and suspended using one of the following electrolyte solutions: phosphate buffered saline (PBS) (pH ~7.2; ionic strength ~170 mM), 168 mM NaCl (pH ~5.7), 5% of PBS (pH ~ 7.2; ionic strength ~ 8 mM) and 8 mM NaCl (pH ~ 5.7). Column transport experiments were performed at 0, 21 and 48 hours following cell harvesting to evaluate the change in cell mobility over time under “starvation” conditions. Our results showed that 1) starvation increased the mobility of E. coli K12 cells; 2) the most significant change in mobility occurred when bacterial cells were suspended in an electrolyte solution that had different pH and ionic strength (i.e., LB-Miller culture suspended in 8 mM NaCl and LB-Luria culture suspended in 168 mM Nacl); and 3) the change in cell mobility primarily occurred within the first 21 hours. The size of the bacterial cells was measured and the surface properties (e.g., zeta potential, hydrophobicity, cell-bound protein, LPS sugar content, outer membrane protein profiles) of the bacterial cells were characterized. We found that the measured cell surface properties could not fully explain the observed changes in cell mobility caused by starvation.

A method for measuring pH at high temperatures is presented

International Nuclear Information System (INIS)

Chaudon, Luc.

1979-01-01

Two hydrogen electrodes are used and set up in a PTFE cell comprising two chambers connected through a saturated potassium chloride solution bridge. This cell is put in an autoclave containing hydrogen. The potential difference of the following cell is measured: H 2 , Pt, R solution - KCl saturated solution at 25 0 C - X solution, Pt, H 2 - The pH of the reference solution R is known up to 300 0 C and the X solution must have its pH to be determined. The precision of the measures at 300 0 C is estimated about +-0,1 pH unit. The dissociation constant of water is calculated from pH variations of alcaline solutions up to 300 0 C. The method has helped to measure the pH at 300 0 C of some boric acid solutions, with or without lithium hydroxide additions, in the following concentration range: B: 250 to 1500 ppm and Li: 0 to 3 ppm. Some concentrations are in fact those chosen for the primary circuits of pressurized water reactors. The pH of ammoniacal solutions is measured too and helped to determine the variations of the dissociation constant of ammonia with temperature [fr

Drivers of sustainable future mobility

DEFF Research Database (Denmark)

Sigurdardottir, Sigrun Birna

This PhD thesis presents three complementary studies that aimed to enhance knowledge of young people’s longitudinal mobility trends and the factors influencing adolescents’ future mobility intentions. First study was an analysis of Danish national travel survey data (TU) from 1995 to 2012....... The sample consisted of young people divided into four age groups: 15-19 year old, 20-24 year old, 25-29 year old and 30-34 year old. The analysis explores the development of gender gaps for rural and urban living location. The mobility indicators analysed were; driving licence status, travel mode, distance...... is still an important subject in transportation research and future development for young people should be monitored closely. The second study was an internet based survey with the aim to explore a range of mediating factors influencing 15 year old adolescents’ intentions to commute by means of car...

High pH solubilization and chromatography-based renaturation and purification of recombinant human granulocyte colony-stimulating factor from inclusion bodies.

Science.gov (United States)

Li, Ming; Fan, Hua; Liu, Jiahua; Wang, Minhong; Wang, Lili; Wang, Chaozhan

2012-03-01

Recombinant human granulocyte colony-stimulating factor (rhG-CSF) is a very efficient therapeutic protein drug which has been widely used in human clinics to treat cancer patients suffering from chemotherapy-induced neutropenia. In this study, rhG-CSF was solubilized from inclusion bodies by using a high-pH solution containing low concentration of urea. It was found that solubilization of the rhG-CSF inclusion bodies greatly depended on the buffer pH employed; alkalic pH significantly favored the solubilization. In addition, when small amount of urea was added to the solution at high pH, the solubilization was further enhanced. After solubilization, the rhG-CSF was renatured with simultaneous purification by using weak anion exchange, strong anion exchange, and hydrophobic interaction chromatography, separately. The results indicated that the rhG-CSF solubilized by the high-pH solution containing low concentration of urea had much higher mass recovery than the one solubilized by 8 M urea when using anyone of the three refolding methods employed in this work. In the case of weak anion exchange chromatography, the high pH solubilized rhG-CSF could get a mass recovery of 73%. The strategy of combining solubilization of inclusion bodies at high pH with refolding of protein using liquid chromatography may become a routine method for protein production from inclusion bodies.

Inferring Human Mobility from Sparse Low Accuracy Mobile Sensing Data

DEFF Research Database (Denmark)

Cuttone, Andrea; Jørgensen, Sune Lehmann; Larsen, Jakob Eg

2014-01-01

Understanding both collective and personal human mobility is a central topic in Computational Social Science. Smartphone sensing data is emerging as a promising source for studying human mobility. However, most literature focuses on high-precision GPS positioning and high-frequency sampling, which...... is not always feasible in a longitudinal study or for everyday applications because location sensing has a high battery cost. In this paper we study the feasibility of inferring human mobility from sparse, low accuracy mobile sensing data. We validate our results using participants' location diaries......, and analyze the inferred geographical networks, the time spent at different places, and the number of unique places over time. Our results suggest that low resolution data allows accurate inference of human mobility patterns....

Metal mobilization under alkaline conditions in ash-covered tailings.

Science.gov (United States)

Lu, Jinmei; Alakangas, Lena; Wanhainen, Christina

2014-06-15

The aim of this study was to determine element mobilization and accumulation in mill tailings under alkaline conditions. The tailings were covered with 50 cm of fly ash, and above a sludge layer. The tailings were geochemically and mineralogically investigated. Sulfides, such as pyrrhotite, sphalerite and galena along with gangue minerals such as dolomite, calcite, micas, chlorite, epidote, Mn-pyroxene and rhodonite were identified in the unoxidized tailings. The dissolution of the fly ash layer resulted in a high pH (close to 12) in the underlying tailings. This, together with the presence of organic matter, increased the weathering of the tailings and mobilization of elements in the uppermost 47 cm of the tailings. All primary minerals were depleted, except quartz and feldspar which were covered by blurry secondary carbonates. Sulfide-associated elements such as Cd, Fe, Pb, S and Zn and silicate-associated elements such as Fe, Mg and Mn were released from the depletion zone and accumulated deeper down in the tailings where the pH decreased to circum-neutral. Sequential extraction suggests that Cd, Cu, Fe, Pb, S and Zn were retained deeper down in the tailings and were mainly associated with the sulfide phase. Calcium, Cr, K and Ni released from the ash layer were accumulated in the uppermost depletion zone of the tailings. Copyright © 2014 Elsevier Ltd. All rights reserved.

Gender Inequalities in Transnational Academic Mobility and the Ideal Type of Academic Entrepreneur

Science.gov (United States)

Leemann, Regula Julia

2010-01-01

Based on a study on academic career paths of PhD graduates in Switzerland, this paper is concerned with the individual and institutional factors that affect transnational academic mobility in the postdoctoral period. It will be argued that the institutionalisation of geographic mobility in academic career paths through research funding…

Thermal Investigation of Three-Dimensional GaN-on-SiC High Electron Mobility Transistors

Science.gov (United States)

2017-07-01

University of L’Aquila, (2011). 23 Rao, H. & Bosman, G. Hot-electron induced defect generation in AlGaN/GaN high electron mobility transistors. Solid...AFRL-RY-WP-TR-2017-0143 THERMAL INVESTIGATION OF THREE- DIMENSIONAL GaN-on-SiC HIGH ELECTRON MOBILITY TRANSISTORS Qing Hao The University of Arizona...clarification memorandum dated 16 Jan 09. This report is available to the general public, including foreign nationals. Copies may be obtained from the

Low pH Cements

International Nuclear Information System (INIS)

Savage, David; Benbow, Steven

2007-05-01

speciation of silicon at pH 10 has a significant impact upon the solubility of montmorillonite and would thus constitute a logical choice of pH limit for cement-derived pore fluids, but it is unlikely that cement-based grouts could be developed to meet this limit. Control of mass transport by diffusion processes serves as a significant constraint over the amount of bentonite that can be degraded. Computer simulations indicate that porosity reduction is likely at the interface between cement and bentonite. However, it is not clear how the transport properties of bentonite may be modified due to mineral alteration processes. There are considerable uncertainties concerning the precise mechanism of the rate of montmorillonite dissolution at elevated pH. The rate of dissolution may be inhibited by the presence of dissolved Si (and perhaps Al), but this mechanism has yet to be confirmed at high pH. The type of secondary minerals assumed to form from cement-bentonite interaction will also have a significant impact upon the rate of montmorillonite dissolution. Low-pH cement systems have received little attention thus far regarding the development of models for the chemical evolution of pore fluids. Low Ca/Si CSH gels show preferential leaching of Si, which is in marked contrast with gels of greater Ca/Si ratio. Models apparently capable of predicting pore fluid composition coexisting with low Ca/Si CSH gels are a modified Berner model and a solid-solution model proposed by Sugiyama and Fujita. The solubility of silica in pore fluids coexisting with low Ca/Si gels may exceed that of amorphous silica, and may pose problems regarding the stability of montmorillonite in relation to framework silicates such as feldspars. However, the potential rate of conversion of montmorillonite to feldspar under repository conditions is uncertain. It is necessary to use additives such as super plasticiser to improve the workability of low-pH cements. These organic additives have the potential to

Low pH Cements

Energy Technology Data Exchange (ETDEWEB)

Savage, David; Benbow, Steven [Quintessa Ltd., Henley-on-Thames (United Kingdom)

2007-05-15

speciation of silicon at pH 10 has a significant impact upon the solubility of montmorillonite and would thus constitute a logical choice of pH limit for cement-derived pore fluids, but it is unlikely that cement-based grouts could be developed to meet this limit. Control of mass transport by diffusion processes serves as a significant constraint over the amount of bentonite that can be degraded. Computer simulations indicate that porosity reduction is likely at the interface between cement and bentonite. However, it is not clear how the transport properties of bentonite may be modified due to mineral alteration processes. There are considerable uncertainties concerning the precise mechanism of the rate of montmorillonite dissolution at elevated pH. The rate of dissolution may be inhibited by the presence of dissolved Si (and perhaps Al), but this mechanism has yet to be confirmed at high pH. The type of secondary minerals assumed to form from cement-bentonite interaction will also have a significant impact upon the rate of montmorillonite dissolution. Low-pH cement systems have received little attention thus far regarding the development of models for the chemical evolution of pore fluids. Low Ca/Si CSH gels show preferential leaching of Si, which is in marked contrast with gels of greater Ca/Si ratio. Models apparently capable of predicting pore fluid composition coexisting with low Ca/Si CSH gels are a modified Berner model and a solid-solution model proposed by Sugiyama and Fujita. The solubility of silica in pore fluids coexisting with low Ca/Si gels may exceed that of amorphous silica, and may pose problems regarding the stability of montmorillonite in relation to framework silicates such as feldspars. However, the potential rate of conversion of montmorillonite to feldspar under repository conditions is uncertain. It is necessary to use additives such as super plasticiser to improve the workability of low-pH cements. These organic additives have the potential to

Metal mobilization from metallurgical wastes by soil organic acids.

Science.gov (United States)

Potysz, Anna; Grybos, Malgorzata; Kierczak, Jakub; Guibaud, Gilles; Fondaneche, Patrice; Lens, Piet N L; van Hullebusch, Eric D

2017-07-01

Three types of Cu-slags differing in chemical and mineralogical composition (historical, shaft furnace, and granulated slags) and a matte from a lead recovery process were studied with respect to their susceptibility to release Cu, Zn and Pb upon exposure to organic acids commonly encountered in soil environments. Leaching experiments (24-960 h) were conducted with: i) humic acid (20 mg/L) at pH t 0  = 4.4, ii) fulvic acid (20 mg/L) at pH t 0  = 4.4, iii) an artificial root exudates (ARE) (17.4 g/L) solution at pH t 0  = 4.4, iv) ARE solution at pH t 0  = 2.9 and v) ultrapure water (pH t 0  = 5.6). The results demonstrated that the ARE contribute the most to the mobilization of metals from all the wastes analyzed, regardless of the initial pH of the solution. For example, up to 14%, 30%, 24% and 5% of Cu is released within 960 h from historical, shaft furnace, granulated slags and lead matte, respectively, when exposed to the artificial root exudates solution (pH 2.9). Humic and fulvic acids were found to have a higher impact on granulated and shaft furnace slags as compared to the ultrapure water control and increased the release of metals by a factor up to 37.5 (Pb) and 20.5 (Cu) for granulated and shaft furnace slags, respectively. Humic and fulvic acids amplified the mobilization of metals by a maximal factor of 13.6 (Pb) and 12.1 (Pb) for historical slag and lead matte, respectively. The studied organic compounds contributed to different release rates of metallic contaminants from individual metallurgical wastes under the conditions tested. Copyright © 2017 Elsevier Ltd. All rights reserved.

Theoretical prediction of high carrier mobility in single-walled black phosphorus nanotubes

Science.gov (United States)

Li, Q. F.; Wang, H. F.; Yang, C. H.; Li, Q. Q.; Rao, W. F.

2018-05-01

One-dimensional semiconductors are promising materials for high-performance nanoscale devices. Using the first-principles calculations combined with deformation potential approximation, we study the electronic structures and carrier transport properties of black phosphorus nanotubes (BPNTs). It is found that both armchair and zigzag BPNTs with diameter 13.5-18.5 Å are direct bandgap semiconductors. At a similar diameter, the carrier mobility of zigzag BPNT is one order of magnitude larger than that of armchair BPNT. For armchair BPNTs, the electron mobility is about 90.70-155.33 cm2 V-1 s-1 at room temperature, which is about three times of its hole counterpart. For zigzag BPNTs, the maximum mobility can reach 2.87 ×103 cm2 V-1 s-1. Furthermore, the electronic properties can be effectively tuned by the strain. For zigzag (0,13) nanotube, there is a direct-to-indirect band gap transition at a tensile strain of about 6%. Moreover, the electron mobility is boosted sharply by one order of magnitude by applying the compressive or tensile strain. The electron mobility increases to 14.05 ×103 cm2 V-1 s-1 at a tensile strain of 9%. Our calculations highlight the tunable electronic properties and superior carrier mobility of BPNTs that are promising for interesting applications in future nano-electronic devices.

Growth parameter optimization and interface treatment for enhanced electron mobility in heavily strained GaInAs/AlInAs high electron mobility transistor structures

International Nuclear Information System (INIS)

Fedoryshyn, Yuriy; Ostinelli, Olivier; Alt, Andreas; Pallin, Angel; Bolognesi, Colombo R.

2014-01-01

The optimization of heavily strained Ga 0.25 In 0.75 As/Al 0.48 In 0.52 As high electron mobility transistor structures is discussed in detail. The growth parameters and the channel layer interfaces were optimized in order to maximize the mobility of the two-dimensional electron gas. Structures composed of an 11 nm thick channel layer and a 4 nm thick spacer layer exhibited electron mobilities as high as 15 100 cm 2 /Vs and 70 000 cm 2 /Vs at 300 and 77 K, respectively, for channels including InAs strained layers. The sheet carrier density was kept above 2.5 × 10 12  cm −2 throughout the entire study

Development of Hybrid pH sensor for long-term seawater pH monitoring.

Science.gov (United States)

Nakano, Y.; Egashira, T.; Miwa, T.; Kimoto, H.

2016-02-01

We have been developing the in situ pH sensor (Hybrid pH sensor: HpHS) for the long-term seawater pH monitoring. We are planning to provide the HpHS for researchers and environmental consultants for observation of the CCS (Carbon dioxide Capture and Storage) monitoring system, the coastal environment monitoring system (e.g. Blue Carbon) and ocean acidification. The HpHS has two types of pH sensors (i.e. potentiometric pH sensor and spectrophotometric pH sensor). The spectrophotometric pH sensor can measure pH correctly and stably, however it needs large power consumption and a lot of reagents in a long period of observation. The pH sensor used m-cresol purple (mCP) as an indicator of pH (Clayton and Byrne, 1993 and Liu et al., 2011). We can choose both coefficients before deployment. On the other hand, although the potentiometric pH sensor is low power consumption and high-speed response (within 10 seconds), drifts in the pH of the potentiometric measurements may possibly occur for a long-term observation. The HpHS can measure in situ pH correctly and stably combining advantage of both pH sensors. The HpHS consists of an aluminum pressure housing with optical cell (main unit) and an aluminum silicon-oil filled, pressure-compensated vessel containing pumps and valves (diaphragm pump and valve unit) and pressure-compensated reagents bags (pH indicator, pure water and Tris buffer or certified reference material: CRM) with an ability to resist water pressure to 3000m depth. The main unit holds system control boards, pump drivers, data storage (micro SD card), LED right source, photodiode, optical cell and pressure proof windows. The HpHS also has an aluminum pressure housing that holds a rechargeable lithium-ion battery or a lithium battery for the power supply (DC 24 V). The HpHS is correcting the value of the potentiometric pH sensor (measuring frequently) by the value of the spectrophotometric pH sensor (measuring less frequently). It is possible to calibrate in

Dynamic patterns and ecological impacts of declining ocean pH in a high-resolution multi-year dataset.

Science.gov (United States)

Wootton, J Timothy; Pfister, Catherine A; Forester, James D

2008-12-02

Increasing global concentrations of atmospheric CO(2) are predicted to decrease ocean pH, with potentially severe impacts on marine food webs, but empirical data documenting ocean pH over time are limited. In a high-resolution dataset spanning 8 years, pH at a north-temperate coastal site declined with increasing atmospheric CO(2) levels and varied substantially in response to biological processes and physical conditions that fluctuate over multiple time scales. Applying a method to link environmental change to species dynamics via multispecies Markov chain models reveals strong links between in situ benthic species dynamics and variation in ocean pH, with calcareous species generally performing more poorly than noncalcareous species in years with low pH. The models project the long-term consequences of these dynamic changes, which predict substantial shifts in the species dominating the habitat as a consequence of both direct effects of reduced calcification and indirect effects arising from the web of species interactions. Our results indicate that pH decline is proceeding at a more rapid rate than previously predicted in some areas, and that this decline has ecological consequences for near shore benthic ecosystems.

How Does School Mobility Impact Indicators of Academic Achievement for Highly Mobile Students?

Science.gov (United States)

Tanner-McBrien, Laura

2010-01-01

Children who are homeless or in foster care change schools more often than their non-mobile peers. The impact of school mobility increases their risk of academic failure (Evans, 1996; Ingersoll, Scamman, & Eckerling, 1989; Mao, 1997, Mehana & Reynolds, 2003; Reynolds & Wolf, 1999). Laws enforcing the right of students to remain in…

Task Phase Recognition for Highly Mobile Workers in Large Building Complexes

DEFF Research Database (Denmark)

Stisen, Allan; Mathisen, Andreas; Krogh, Søren

2016-01-01

requirements on the accuracy of the indoor positioning, and thus come with low deployment and maintenance effort in real-world settings. We evaluated the proposed methods in a large hospital complex, where the highly mobile workers were recruited among the non-clinical workforce. The evaluation is based......-scale indoor work environments, namely from a WiFi infrastructure providing coarse grained indoor positioning, from inertial sensors in the workers’ mobile phones, and from a task management system yielding information about the scheduled tasks’ start and end locations. The methods presented have low...... on manually labelled real-world data collected over 4 days of regular work life of the mobile workforce. The collected data yields 83 tasks in total involving 8 different orderlies from a major university hospital with a building area of 160, 000 m2. The results show that the proposed methods can distinguish...

High mobility two-dimensional electron gases in nitride heterostructures with high Al composition AlGaN alloy barriers

International Nuclear Information System (INIS)

Li Guowang; Cao Yu; Xing Huili Grace; Jena, Debdeep

2010-01-01

We report high-electron mobility nitride heterostructures with >70% Al composition AlGaN alloy barriers grown by molecular beam epitaxy. Direct growth of such AlGaN layers on GaN resulted in hexagonal trenches and a low mobility polarization-induced charge. By applying growth interruption at the heterojunction, the surface morphology improved dramatically and the room temperature two-dimensional electron gas (2DEG) mobility increased by an order of magnitude, exceeding 1300 cm 2 /V s. The 2DEG density was tunable at 0.4-3.7x10 13 /cm 2 by varying the total barrier thickness (t). Surface barrier heights of the heterostructures were extracted and exhibited dependence on t.

Influence of pH on the transport of nanoscale zinc oxide in saturated porous media

Energy Technology Data Exchange (ETDEWEB)

Kanel, Sushil R. [Pegasus Technical Services, Inc. (United States); Al-Abed, Souhail R., E-mail: al-abed.souhail@epa.gov [National Risk Management Research Laboratory, U.S. Environmental Protection Agency (United States)

2011-09-15

Widespread use of nanoscale zinc oxide (nZnO) in various fields causes subsurface environment contamination. Even though the transport of dissolved zinc ions in subsurface environments such as soils and sediments has been widely studied, the transport mechanism of nZnO in such environments is poorly understood. In addition, nZnO is often combined with stabilizers or dispersing agents to prevent its aggregation in products. The purpose of this study is to determine the influence of pH on the transport properties of pristine nZnO and carboxymethyl cellulose (CMC) stabilized nZnO (CMC-nZnO) suspensions in silica sand packed column under saturated flow conditions. Transport data were collected at different pHs (pHs: 3, 7, 9, and 11) under 1 mL/min flow rate conditions in a 1.1 cm diameter column. It is found that the transport trends of pristine nZnO and CMC-nZnO were different. For pristine nZnO, mobility of total Zn reached a minimum around its point of zero charge (pH 8.9). Whereas in the case of CMC-nZnO, the mobility of total Zn decreased as the pH of the solution pH increased from 3 to 11. ZnO and Zn ion mixture were separated using diafiltration membrane. It showed that most of the nZnO and CMC-nZnO exists as Zn ion at pH 3 before and after eluting from the sand packed column whereas at pH 11, they exist as particles. This study shows the strong influence of pH and stabilizing agents on nZnO transport. These factors should be considered during subsurface transport of nZnO.

Influence of pH on the transport of nanoscale zinc oxide in saturated porous media

International Nuclear Information System (INIS)

Kanel, Sushil R.; Al-Abed, Souhail R.

2011-01-01

Widespread use of nanoscale zinc oxide (nZnO) in various fields causes subsurface environment contamination. Even though the transport of dissolved zinc ions in subsurface environments such as soils and sediments has been widely studied, the transport mechanism of nZnO in such environments is poorly understood. In addition, nZnO is often combined with stabilizers or dispersing agents to prevent its aggregation in products. The purpose of this study is to determine the influence of pH on the transport properties of pristine nZnO and carboxymethyl cellulose (CMC) stabilized nZnO (CMC–nZnO) suspensions in silica sand packed column under saturated flow conditions. Transport data were collected at different pHs (pHs: 3, 7, 9, and 11) under 1 mL/min flow rate conditions in a 1.1 cm diameter column. It is found that the transport trends of pristine nZnO and CMC–nZnO were different. For pristine nZnO, mobility of total Zn reached a minimum around its point of zero charge (pH 8.9). Whereas in the case of CMC–nZnO, the mobility of total Zn decreased as the pH of the solution pH increased from 3 to 11. ZnO and Zn ion mixture were separated using diafiltration membrane. It showed that most of the nZnO and CMC–nZnO exists as Zn ion at pH 3 before and after eluting from the sand packed column whereas at pH 11, they exist as particles. This study shows the strong influence of pH and stabilizing agents on nZnO transport. These factors should be considered during subsurface transport of nZnO.

Highly Sensitive and Reproducible SERS Sensor for Biological pH Detection Based on a Uniform Gold Nanorod Array Platform.

Science.gov (United States)

Bi, Liyan; Wang, Yunqing; Yang, Ying; Li, Yuling; Mo, Shanshan; Zheng, Qingyin; Chen, Lingxin

2018-05-09

Conventional research on surface-enhanced Raman scattering (SERS)-based pH sensors often depends on nanoparticle aggregation, whereas the variability in nanoparticle aggregation gives rise to poor repeatability in the SERS signal. Herein, we fabricated a gold nanorod array platform via an efficient evaporative self-assembly method. The platform exhibits great SERS sensitivity with an enhancement factor of 5.6 × 10 7 and maintains excellent recyclability and reproducibility with relative standard deviation (RSD) values of less than 8%. On the basis of the platform, we developed a highly sensitive bovine serum albumin (BSA)-coated 4-mercaptopyridine (4-MPy)-linked (BMP) SERS-based pH sensor to report pH ranging from pH 3.0 to pH 8.0. The intensity ratio variation of 1004 and 1096 cm -1 in 4-MPy showed excellent pH sensitivity, which decreased as the surrounding pH increased. Furthermore, this BMP SERS-based pH sensor was employed to measure the pH value in C57BL/6 mouse blood. We have demonstrated that the pH sensor has great advantages such as good stability, reliability, and accuracy, which could be extended for the design of point-of-care devices.

High-sensitivity pH sensor using separative extended-gate field-effect transistors with single-walled carbon-nanotube networks

Science.gov (United States)

Pyo, Ju-Young; Cho, Won-Ju

2018-04-01

We fabricate high-sensitivity pH sensors using single-walled carbon-nanotube (SWCNT) network thin-film transistors (TFTs). The sensing and transducer parts of the pH sensor are composed of separative extended-sensing gates (ESGs) with SnO2 ion-sensitive membranes and double-gate structure TFTs with thin SWCNT network channels of ∼1 nm and AlO x top-gate insulators formed by the solution-deposition method. To prevent thermal process-induced damages on the SWCNT channel layer due to the post-deposition annealing process and improve the electrical characteristics of the SWCNT-TFTs, microwave irradiation is applied at low temperatures. As a result, a pH sensitivity of 7.6 V/pH, far beyond the Nernst limit, is obtained owing to the capacitive coupling effect between the top- and bottom-gate insulators of the SWCNT-TFTs. Therefore, double-gate structure SWCNT-TFTs with separated ESGs are expected to be highly beneficial for high-sensitivity disposable biosensor applications.

Japanese high school students' usage of mobile phones while cycling.

Science.gov (United States)

Ichikawa, Masao; Nakahara, Shinji

2008-03-01

To investigate the perception and actual use of mobile phones among Japanese high school students while riding their bicycles, and their experience of bicycle crash/near-crash. A questionnaire survey was carried out at high schools that were, at the time of the survey, commissioned by the National Agency for the Advancement of Sports and Health to conduct school safety research. In the survey, we found that mobile phone use while riding a bicycle was quite common among the students during their commute, but those who have a higher perception of danger in this practice, and those who perceived that this practice is prohibited, were less likely to engage in this practice. Male students and students commuting to school by bicycle only were more likely to have used phones while riding. There was a significant relationship between phone usage while riding a bicycle and the experience of bicycle crash/near-crash, although its causality was not established. Bicycle crash/near-crash experienced while using a phone was less prevalent among the students who had a higher perception of danger in phone usage while riding, students who perceived that this practice is prohibited, and students with a shorter travel time by bicycle during the commute. Since mobile phone use while riding a bicycle potentially increases crash risk among cyclists, student bicycle commuters should be made aware of this risk. Moreover, they should be informed that cyclists' phone usage while riding is prohibited according to the road traffic law.

The design of a linear L-band high power amplifier for mobile communication satellites

Science.gov (United States)

Whittaker, N.; Brassard, G.; Li, E.; Goux, P.

1990-01-01

A linear L-band solid state high power amplifier designed for the space segment of the Mobile Satellite (MSAT) mobile communication system is described. The amplifier is capable of producing 35 watts of RF power with multitone signal at an efficiency of 25 percent and with intermodulation products better than 16 dB below carrier.

Thermally Dried Ink-Jet Process for 6,13-Bis(triisopropylsilylethynyl)-Pentacene for High Mobility and High Uniformity on a Large Area Substrate

Science.gov (United States)

Ryu, Gi Seong; Lee, Myung Won; Jeong, Seung Hyeon; Song, Chung Kun

2012-05-01

In this study we developed a simple ink-jet process for 6,13-bis(triisopropylsilylethynyl)-pentacene (TIPS-pentacene), which is known as a high-mobility soluble organic semiconductor, to achieve relatively high-mobility and high-uniformity performance for large-area applications. We analyzed the behavior of fluorescent particles in droplets and applied the results to determining a method of controlling the behavior of TIPS-pentacene molecules. The grain morphology of TIPS-pentacene varied depending on the temperature applied to the droplets during drying. We were able to obtain large and uniform grains at 46 °C without any “coffee stain”. The process was applied to a large-size organic thin-film transistor (OTFT) backplane for an electrophoretic display panel containing 192×150 pixels on a 6-in.-sized substrate. The average of mobilities of 36 OTFTs, which were taken from different locations of the backplane, was 0.44±0.08 cm2·V-1·s-1, with a small deviation of 20%, over a 6-in.-size area comprising 28,800 OTFTs. This process providing high mobility and high uniformity can be achieved by simply maintaining the whole area of the substrate at a specific temperature (46 °C in this case) during drying of the droplets.

Thermally dried ink-jet process for 6,13-bis(triisopropylsilylethynyl)-pentacene for high mobility and high uniformity on a large area substrate

Science.gov (United States)

Ryu, Gi Seong; Lee, Myung Won; Jeong, Seung Hyeon; Song, Chung Kun

2012-01-01

In this study we developed a simple ink-jet process for 6,13-bis(triisopropylsilylethynyl)-pentacene (TIPS-pentacene), which is known as a high-mobility soluble organic semiconductor, to achieve relatively high-mobility and high-uniformity performance for large-area applications. We analyzed the behavior of fluorescent particles in droplets and applied the results to determining a method of controlling the behavior of TIPS-pentacene molecules. The grain morphology of TIPS-pentacene varied depending on the temperature applied to the droplets during drying. We were able to obtain large and uniform grains at 46 degrees C without any "coffee stain". The process was applied to a large-size organic thin-film transistor (OTFT) backplane for an electrophoretic display panel containing 192 x 150 pixels on a 6-in.-sized substrate. The average of mobilities of 36 OTFTs, which were taken from different locations of the backplane, was 0.44 +/- 0.08 cm2.V-1.s-1, with a small deviation of 20%, over a 6-in.-size area comprising 28,800 OTFTs. This process providing high mobility and high uniformity can be achieved by simply maintaining the whole area of the substrate at a specific temperature (46 degrees C in this case) during drying of the droplets.

Mobilities

DEFF Research Database (Denmark)

to social networks, personal identities, and our relationship to the built environment. The omnipresence of mobilities within everyday life, high politics, technology, and tourism (to mention but a few) all point to a key insight harnessed by the ‘mobilities turn’. Namely that mobilities is much more than......The world is on the move. This is a widespread understanding by many inhabitants of contemporary society across the Globe. But what does it actually mean? During over one decade the ‘mobilities turn’ within the social sciences have provided a new set of insights into the repercussions of mobilities...... and environmental degradation. The spaces and territories marked by mobilities as well as the sites marked by the bypassing of such are explored. Moreover, the architectural and technological dimensions to infrastructures and sites of mobilities will be included as well as the issues of power, social exclusion...

Fabrication and Evaluation of a New High-Temperature pH Sensor for Use in PWR Nuclear Power Plants

Energy Technology Data Exchange (ETDEWEB)

Jung, Yong Ju [Korea University of Technology and Education, Cheonan (Korea, Republic of); Yeon, Jei Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2010-10-15

A new high-temperature pH sensor has been successfully developed by reforming the internal reference systems of the pH sensors based on oxygen-ion conducting ceramic membrane. The conventional internal reference system, a mixture of Ni and NiO, has been replaced with partially oxidized Ni powders, where Ni and NiO coexist on the surface of particles, in order to avoid the cumbersome mixing step of Ni and NiO particles. The partially oxidized Ni particles were made by oxidizing Ni under air atmosphere at 600 .deg. C and characterized by X-ray diffraction (XRD) and FTIR spectroscopy. The viability of the pH sensor developed was assessed in boric acid (1000 ppm-B) / lithium hydroxide (1 to 3 ppm-Li) buffer solutions at 280 .deg. C. The pH sensor showed excellent accuracy with a small error less than ±0.2 pH units.

Fabrication and Evaluation of a New High-Temperature pH Sensor for Use in PWR Nuclear Power Plants

International Nuclear Information System (INIS)

Jung, Yong Ju; Yeon, Jei Won

2010-01-01

A new high-temperature pH sensor has been successfully developed by reforming the internal reference systems of the pH sensors based on oxygen-ion conducting ceramic membrane. The conventional internal reference system, a mixture of Ni and NiO, has been replaced with partially oxidized Ni powders, where Ni and NiO coexist on the surface of particles, in order to avoid the cumbersome mixing step of Ni and NiO particles. The partially oxidized Ni particles were made by oxidizing Ni under air atmosphere at 600 .deg. C and characterized by X-ray diffraction (XRD) and FTIR spectroscopy. The viability of the pH sensor developed was assessed in boric acid (1000 ppm-B) / lithium hydroxide (1 to 3 ppm-Li) buffer solutions at 280 .deg. C. The pH sensor showed excellent accuracy with a small error less than ±0.2 pH units

"It's a Way of Life for Us": High Mobility and High Achievement in Department of Defense Schools.

Science.gov (United States)

Smrekar, Claire E.; Owens, Debra E.

2003-01-01

Examines the academic performance of students in U.S. Department of Defense Education Activity (DoDEA) schools, which have high student mobility. Some observers contend that these students' high achievement is a function of their middle class family and community characteristics. Asserts that DoDEA schools simultaneously "do the right…

Atomic layer deposition of high-mobility hydrogen-doped zinc oxide

NARCIS (Netherlands)

Macco, B.; Knoops, H.C.M.; Verheijen, M.A.; Beyer, W.; Creatore, M.; Kessels, W.M.M.

2017-01-01

In this work, atomic layer deposition (ALD) has been employed to prepare high-mobility H-doped zinc oxide (ZnO:H) films. Hydrogen doping was achieved by interleaving the ZnO ALD cycles with H2 plasma treatments. It has been shown that doping with H2 plasma offers key advantages over traditional

Hold the Phone! High School Students' Perceptions of Mobile Phone Integration in the Classroom

Science.gov (United States)

Thomas, Kevin; Muñoz, Marco A.

2016-01-01

This study examined the survey responses of 628 high school students in a large urban school district to determine their perceptions of mobile phone use in the classroom. Findings indicated that the majority of students (90.7%) were using a variety of mobile phone features for school-related work. Student support for instructional uses of phones,…

Spectroscopic determination of pH

International Nuclear Information System (INIS)

Faanu, A.; Glover, E.T.; Bailey, E.; Rochelle, C.

2009-01-01

A technique of measuring pH at temperature range of 20 - 70 0 C and high pressure conditions of 1 - 200 atmospheres has been developed by relating the ratio of absorbance peaks of indicator solutions (basic and acidic) as a function of pH, using ultraviolet-visible spectrophotometer. The pH values of the buffer solutions measured at 20 0 C and 70 0 C indicated slight temperature dependence, while the pressure had no effect. The pH of the buffer solutions increased with temperature with relative standard deviations in the range 0.4 - 0.5 % at 95 % confidence interval. The possible causes of the temperature dependence were attributed to changes in pH values as the temperature changed. (au)

Increase in electron mobility of InGaAs/InP composite channel high electron mobility transistor structure due to SiN passivation

International Nuclear Information System (INIS)

Liu Yuwei; Wang Hong; Radhakrishnan, K.

2007-01-01

The influence of silicon nitride passivation on electron mobility of InGaAs/InP composite channel high electron mobility transistor structure has been studied. Different from the structures with single InGaAs channel, an increase in effective mobility μ e with a negligible change of sheet carrier density n s after SiN deposition is clearly observed in the composite channel structures. The enhancement of μ e could be explained under the framework of electrons transferring from the InP sub-channel into InGaAs channel region due to the energy band bending at the surface region caused by SiN passivation, which is further confirmed by low temperature photoluminescence measurements

The influence of pH and reaction time on the formation of FeSe{sub 2} upon selenite reduction by nano-sized pyrite-greigite

Energy Technology Data Exchange (ETDEWEB)

Kang, Mingliang [Sun Yat-sen Univ., Zhuhai (China). Sino-French Institute of Nuclear Engineering and Technology; Bardelli, Fabrizio; Ma, Bin; Charlet, Laurent [Grenoble Univ. (France). Environmental Geochemistry Group; Chen, Fanrong; Yang, Yongqiang [Chinese Academy of Sciences, Guangzhou (China). Key Laboratory of Mineralogy and Metallogeny; Chinese Academy of Sciences, Guangzhou (China). Guangdong Provincial Key Laboratory of Mineral Physics and Materials

2016-11-01

The influence of pH and reaction time on the formation of FeSe{sub 2} by reductive precipitation of Se(IV) with nano-sized pyrite-greigite was investigated. Reductive precipitation is an effective method of attenuating the mobility of {sup 79}Se, which is foreseen to be a dangerous radioisotope for the geological disposal of high-level radioactive waste (HLW). The results indicated that Se(0)was formed at pH <4.05, whereas, at pH > 6.07, considerable amount of FeSe{sub 2} was formed along with Se(0). These observations are in agreement with the thermodynamic predictions reported in this work. Furthermore, the formation of FeSe{sub 2} was found to continue by increasing the reaction time, indicating that the Se(0) formed in the early reaction stage is gradually transformed to FeSe{sub 2} upon the depletion of aqueous Se(IV). Since FeSe{sub 2} has a stronger reactivity than pyrite, it was proposed that greigite, rather than pyrite, was responsible for the formation of FeSe{sub 2}. The findings in this study are of interest for key geochemical processes governing the mobility of toxic {sup 79}Se in the environment in presence of iron sulfides.

Client Mobile Software Design Principles for Mobile Learning Systems

Directory of Open Access Journals (Sweden)

Qing Tan

2009-01-01

Full Text Available In a client-server mobile learning system, client mobile software must run on the mobile phone to acquire, package, and send student’s interaction data via the mobile communications network to the connected mobile application server. The server will receive and process the client data in order to offer appropriate content and learning activities. To develop the mobile learning systems there are a number of very important issues that must be addressed. Mobile phones have scarce computing resources. They consist of heterogeneous devices and use various mobile operating systems, they have limitations with their user/device interaction capabilities, high data communications cost, and must provide for device mobility and portability. In this paper we propose five principles for designing Client mobile learning software. A location-based adaptive mobile learning system is presented as a proof of concept to demonstrate the applicability of these design principles.

Determination of free acid in high level liquid wastes by means of fixed pH value

International Nuclear Information System (INIS)

Li Jifu; Duan Shirong; Wu Xi; Yu Xueren

1991-01-01

For the determination of free acid in high level liquid wastes, 8% potassium oxalate solution with pH 6.50 as a complex agent of hydrolizable ion is added to 1 AW and the solution is titrated with standard sodium hydroxide to reach the original pH value. The quantity of free acid is calculated by standard sodium hydroxide consumed. This method is simple, rapid and accurate. The relative error of analysis is less than ±4%. The average percentage of recovery is 99.6-101.0%

A PhD is a PhD is a PhD

OpenAIRE

Ostrow, Deborah Anne

2017-01-01

A PhD is a PhD is a PhD is a practice-based project that interrogates the process of an artist undertaking PhD research under established criteria. It consists of an exegesis, an original screenplay, and a digital film made for online viewing, with images drawn from a range of documentaries and films found on YouTube. They have been dissected, re-assembled and then re-embedded to YouTube. The source material covers topics such as medicalization of madness, the conspicuous appropriation of uni...

Aluminum gallium nitride (GaN)/GaN high electron mobility transistor-based sensors for glucose detection in exhaled breath condensate.

Science.gov (United States)

Chu, Byung Hwan; Kang, Byoung Sam; Hung, Sheng Chun; Chen, Ke Hung; Ren, Fan; Sciullo, Andrew; Gila, Brent P; Pearton, Stephen J

2010-01-01

Immobilized aluminum gallium nitride (AlGaN)/GaN high electron mobility transistors (HEMTs) have shown great potential in the areas of pH, chloride ion, and glucose detection in exhaled breath condensate (EBC). HEMT sensors can be integrated into a wireless data transmission system that allows for remote monitoring. This technology offers the possibility of using AlGaN/GaN HEMTs for extended investigations of airway pathology of detecting glucose in EBC without the need for clinical visits. HEMT structures, consisting of a 3-microm-thick undoped GaN buffer, 30-A-thick Al(0.3)Ga(0.7)N spacer, and 220-A-thick silicon-doped Al(0.3)Ga(0.7)N cap layer, were used for fabricating the HEMT sensors. The gate area of the pH, chloride ion, and glucose detection was immobilized with scandium oxide (Sc(2)O(3)), silver chloride (AgCl) thin film, and zinc oxide (ZnO) nanorods, respectively. The Sc(2)O(3)-gated sensor could detect the pH of solutions ranging from 3 to 10 with a resolution of approximately 0.1 pH. A chloride ion detection limit of 10(-8) M was achieved with a HEMT sensor immobilized with the AgCl thin film. The drain-source current of the ZnO nanorod-gated AlGaN/GaN HEMT sensor immobilized with glucose oxidase showed a rapid response of less than 5 seconds when the sensor was exposed to the target glucose in a buffer with a pH value of 7.4. The sensor could detect a wide range of concentrations from 0.5 nM to 125 microM. There is great promise for using HEMT-based sensors to enhance the detection sensitivity for glucose detection in EBC. Depending on the immobilized material, HEMT-based sensors can be used for sensing different materials. These electronic detection approaches with rapid response and good repeatability show potential for the investigation of airway pathology. The devices can also be integrated into a wireless data transmission system for remote monitoring applications. This sensor technology could use the exhaled breath condensate to measure the

Assessment of fly ash-aided phytostabilisation of highly contaminated soils after an 8-year field trial

Energy Technology Data Exchange (ETDEWEB)

Lopareva-Pohu, Alena [Universite Lille Nord de France, Lille (France); Groupe ISA, Equipe Sols et Environnement, Laboratoire Genie Civil et geoEnvironnement Lille Nord de France EA 4515, 48 boulevard Vauban, 59046 Lille Cedex (France); Universite du Littoral-Cote d' Opale, Unite de Chimie Environnementale et Interactions sur le Vivant (UCEIV), EA4492, Maison de la Recherche en Environnement Industriel de Dunkerque 2, Avenue Maurice Schumann, 59140 Dunkerque (France); Pourrut, Bertrand; Waterlot, Christophe [Universite Lille Nord de France, Lille (France); Groupe ISA, Equipe Sols et Environnement, Laboratoire Genie Civil et geoEnvironnement Lille Nord de France EA 4515, 48 boulevard Vauban, 59046 Lille Cedex (France); Garcon, Guillaume [Universite Lille Nord de France, Lille (France); Universite du Littoral-Cote d' Opale, Unite de Chimie Environnementale et Interactions sur le Vivant (UCEIV), EA4492, Maison de la Recherche en Environnement Industriel de Dunkerque 2, Avenue Maurice Schumann, 59140 Dunkerque (France); Bidar, Geraldine; Pruvot, Christelle [Universite Lille Nord de France, Lille (France); Groupe ISA, Equipe Sols et Environnement, Laboratoire Genie Civil et geoEnvironnement Lille Nord de France EA 4515, 48 boulevard Vauban, 59046 Lille Cedex (France); Shirali, Pirouz [Universite Lille Nord de France, Lille (France); Universite du Littoral-Cote d' Opale, Unite de Chimie Environnementale et Interactions sur le Vivant (UCEIV), EA4492, Maison de la Recherche en Environnement Industriel de Dunkerque 2, Avenue Maurice Schumann, 59140 Dunkerque (France); Douay, Francis, E-mail: f.douay@isa-lille.fr [Universite Lille Nord de France, Lille (France); Groupe ISA, Equipe Sols et Environnement, Laboratoire Genie Civil et geoEnvironnement Lille Nord de France EA 4515, 48 boulevard Vauban, 59046 Lille Cedex (France)

2011-01-01

Sustainable management of large surface areas contaminated with trace elements is a real challenge, since currently applied remediation techniques are too expensive for these areas. Aided phytostabilisation appears to be a cost efficient technique to reduce metal mobility in contaminated soils and contaminated particle spread. In this context, this study aimed at evaluating the long-term efficiency of aided phytostabilisation on former agricultural soils highly contaminated with trace elements. The influence of afforestation and fly ash amendments to reduce metal mobility was investigated. Before being planted with a tree mix, the study site was divided into three plots: a reference plot with no amendment, the second amended with silico-aluminous fly ash and the third with sulfo-calcic fly ash. After eight years, some soil physico-chemical parameters, including cadmium (Cd), lead (Pb) and zinc (Zn) extractability were modified. In particular, pH decreased on the whole site while organic carbon content increased. The alteration of these parameters influencing trace element mobility is explained by afforestation. Over time, concentrations of CaCl{sub 2}-extractable metals increased and were correlated with the soil pH decrease. In the amended soils, extractable Cd, Pb and Zn concentrations were lower than in the reference soil. The results indicated that the two fly ashes buffered natural soil acidification due to vegetation development and limited trace element mobility and thus could limit their bioavailability. For long-term phytostabilisation, special attention should be focused on the soil pH, metal mobility and phytoavailability analysis. - Research Highlights: {yields} Afforestation leads to soil pH decrease and organic carbon content increase. {yields} Fly ashes buffered natural soil acidification. {yields} Fly ashes limited metal mobility.

Assessment of fly ash-aided phytostabilisation of highly contaminated soils after an 8-year field trial

International Nuclear Information System (INIS)

Lopareva-Pohu, Alena; Pourrut, Bertrand; Waterlot, Christophe; Garcon, Guillaume; Bidar, Geraldine; Pruvot, Christelle; Shirali, Pirouz; Douay, Francis

2011-01-01

Sustainable management of large surface areas contaminated with trace elements is a real challenge, since currently applied remediation techniques are too expensive for these areas. Aided phytostabilisation appears to be a cost efficient technique to reduce metal mobility in contaminated soils and contaminated particle spread. In this context, this study aimed at evaluating the long-term efficiency of aided phytostabilisation on former agricultural soils highly contaminated with trace elements. The influence of afforestation and fly ash amendments to reduce metal mobility was investigated. Before being planted with a tree mix, the study site was divided into three plots: a reference plot with no amendment, the second amended with silico-aluminous fly ash and the third with sulfo-calcic fly ash. After eight years, some soil physico-chemical parameters, including cadmium (Cd), lead (Pb) and zinc (Zn) extractability were modified. In particular, pH decreased on the whole site while organic carbon content increased. The alteration of these parameters influencing trace element mobility is explained by afforestation. Over time, concentrations of CaCl 2 -extractable metals increased and were correlated with the soil pH decrease. In the amended soils, extractable Cd, Pb and Zn concentrations were lower than in the reference soil. The results indicated that the two fly ashes buffered natural soil acidification due to vegetation development and limited trace element mobility and thus could limit their bioavailability. For long-term phytostabilisation, special attention should be focused on the soil pH, metal mobility and phytoavailability analysis. - Research Highlights: → Afforestation leads to soil pH decrease and organic carbon content increase. → Fly ashes buffered natural soil acidification. → Fly ashes limited metal mobility.

High electron mobility recovery in AlGaN/GaN 2DEG channels regrown on etched surfaces

International Nuclear Information System (INIS)

Chan, Silvia H; DenBaars, Steven P; Keller, Stacia; Tahhan, Maher; Li, Haoran; Romanczyk, Brian; Mishra, Umesh K

2016-01-01

This paper reports high two-dimensional electron gas mobility attained from the regrowth of the AlGaN gating layer on ex situ GaN surfaces. To repair etch-damaged GaN surfaces, various pretreatments were conducted via metalorganic chemical vapor deposition, followed by a regrown AlGaN/GaN mobility test structure to evaluate the extent of recovery. The developed treatment process that was shown to significantly improve the electron mobility consisted of a N 2  + NH 3 pre-anneal plus an insertion of a 4 nm or thicker GaN interlayer prior to deposition of the AlGaN gating layer. Using the optimized process, a high electron mobility transistor (HEMT) device was fabricated which exhibited a high mobility of 1450 cm 2 V −1 s −1 (R sh  = 574 ohm/sq) and low dispersion characteristics. The additional inclusion of an in situ Al 2 O 3 dielectric into the regrowth process for MOS-HEMTs still preserved the transport properties near etch-impacted areas. (paper)

Carbon dots with strong excitation-dependent fluorescence changes towards pH. Application as nanosensors for a broad range of pH

Energy Technology Data Exchange (ETDEWEB)

Barati, Ali [Faculty of Chemistry, Institute for Advanced Studies in Basic Sciences, Zanjan (Iran, Islamic Republic of); Department of Chemistry, Razi University, Kermanshah (Iran, Islamic Republic of); Shamsipur, Mojtaba, E-mail: mshamsipur@yahoo.com [Department of Chemistry, Razi University, Kermanshah (Iran, Islamic Republic of); Abdollahi, Hamid, E-mail: abd@iasbs.ac.ir [Faculty of Chemistry, Institute for Advanced Studies in Basic Sciences, Zanjan (Iran, Islamic Republic of)

2016-08-10

In this study, preparation of novel pH-sensitive N-doped carbon dots (NCDs) using glucose and urea is reported. The prepared NCDs present strong excitation-dependent fluorescence changes towards the pH that is a new behavior from these nanomaterials. By taking advantage of this unique behavior, two separated ratiometric pH sensors using emission spectra of the NCDs for both acidic (pH 2.0 to 8.0) and basic (pH 7.0 to 14.0) ranges of pH are constructed. Additionally, by considering the entire Excitation–Emission Matrix (EEM) of NCDs as analytical signal and using a suitable multivariate calibration method, a broad range of pH from 2.0 to 14.0 was well calibrated. The multivariate calibration method was independent from the concentration of NCDs and resulted in a very low average prediction error of 0.067 pH units. No changes in the predicted pH under UV irradiation (for 3 h) and at high ionic strength (up to 2 M NaCl) indicated the high stability of this pH nanosensor. The practicality of this pH nanosensor for pH determination in real water samples was validated with good accuracy and repeatability. - Highlights: • Novel pH-sensitive carbon dots with strong FL changes towards pH are reported. • Ratiometric FL pH-sensors for both acidic and basic ranges of pH are constructed. • Multivariate calibration methods were used to calibrate a broad range of pH. • Using EEM of carbon dots and ANN, pH from 2.0 to 14.0 was well calibrated. • The pH prediction is stable even at high ionic strength up to 2 M NaCl.

Carbon dots with strong excitation-dependent fluorescence changes towards pH. Application as nanosensors for a broad range of pH

International Nuclear Information System (INIS)

Barati, Ali; Shamsipur, Mojtaba; Abdollahi, Hamid

2016-01-01

In this study, preparation of novel pH-sensitive N-doped carbon dots (NCDs) using glucose and urea is reported. The prepared NCDs present strong excitation-dependent fluorescence changes towards the pH that is a new behavior from these nanomaterials. By taking advantage of this unique behavior, two separated ratiometric pH sensors using emission spectra of the NCDs for both acidic (pH 2.0 to 8.0) and basic (pH 7.0 to 14.0) ranges of pH are constructed. Additionally, by considering the entire Excitation–Emission Matrix (EEM) of NCDs as analytical signal and using a suitable multivariate calibration method, a broad range of pH from 2.0 to 14.0 was well calibrated. The multivariate calibration method was independent from the concentration of NCDs and resulted in a very low average prediction error of 0.067 pH units. No changes in the predicted pH under UV irradiation (for 3 h) and at high ionic strength (up to 2 M NaCl) indicated the high stability of this pH nanosensor. The practicality of this pH nanosensor for pH determination in real water samples was validated with good accuracy and repeatability. - Highlights: • Novel pH-sensitive carbon dots with strong FL changes towards pH are reported. • Ratiometric FL pH-sensors for both acidic and basic ranges of pH are constructed. • Multivariate calibration methods were used to calibrate a broad range of pH. • Using EEM of carbon dots and ANN, pH from 2.0 to 14.0 was well calibrated. • The pH prediction is stable even at high ionic strength up to 2 M NaCl.

High-mobility germanium p-MOSFETs by using HCl and (NH4)2S surface passivation

International Nuclear Information System (INIS)

Xue Bai-Qing; Wang Sheng-Kai; Han Le; Chang Hu-Dong; Sun Bing; Zhao Wei; Liu Hong-Gang

2013-01-01

To achieve a high-quality high-κ/Ge interfaces for high hole mobility Ge p-MOSFET applications, a simple chemical cleaning and surface passivation scheme is introduced, and Ge p-MOSFETs with effective channel hole mobility up to 665 cm 2 /V·s are demonstrated on a Ge (111) substrate. Moreover, a physical model is proposed to explain the dipole layer formation at the metal—oxide—semiconductor (MOS) interface by analyzing the electrical characteristics of HCl- and (NH 4 ) 2 S-passivated samples. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Highly Stretchable Potentiometric pH Sensor Fabricated via Laser Carbonization and Machining of Carbon-Polyaniline Composite.

Science.gov (United States)

Rahimi, Rahim; Ochoa, Manuel; Tamayol, Ali; Khalili, Shahla; Khademhosseini, Ali; Ziaie, Babak

2017-03-15

The development of stretchable sensors has recently attracted considerable attention. These sensors have been used in wearable and robotics applications, such as personalized health-monitoring, motion detection, and human-machine interfaces. Herein, we report on a highly stretchable electrochemical pH sensor for wearable point-of-care applications that consists of a pH-sensitive working electrode and a liquid-junction-free reference electrode, in which the stretchable conductive interconnections are fabricated by laser carbonizing and micromachining of a polyimide sheet bonded to an Ecoflex substrate. This method produces highly porous carbonized 2D serpentine traces that are subsequently permeated with polyaniline (PANI) as the conductive filler, binding material, and pH-sensitive membrane. The experimental and simulation results demonstrate that the stretchable serpentine PANI/C-PI interconnections with an optimal trace width of 0.3 mm can withstand elongations of up to 135% and are robust to more than 12 000 stretch-and-release cycles at 20% strain without noticeable change in the resistance. The pH sensor displays a linear sensitivity of -53 mV/pH (r 2 = 0.976) with stable performance in the physiological range of pH 4-10. The sensor shows excellent stability to applied longitudinal and transverse strains up to 100% in different pH buffer solutions with a minimal deviation of less than ±4 mV. The material biocompatibility is confirmed with NIH 3T3 fibroblast cells via PrestoBlue assays.

Emergent structures in faculty hiring networks, and the effects of mobility on academic performance

NARCIS (Netherlands)

Cowan, Robin; Rossello, Giulia

2017-01-01

This paper is about the South African job market for PhDs. PhD to first job mobility involves the preferences of both the hiring institution and the candidate. Both want to make the best choice and here institutional prestige plays a crucial role. A university’s prestige is an emergent property of

PH- Mapping Of Prepubertal Skin Of Indian Subjects

Directory of Open Access Journals (Sweden)

Gupta A B

1995-01-01

Full Text Available PH- mapping of skin was made by measuring the skin surface pH in 61 normal Indian subjects (35M, 26F in the prepubertal age group at 21 different sites from scalp to sole at an ambient temperature 25-32C and a relative humidity 60-65%. The pH values at axilla, umbilicus, palm, fingerfolds, foot, sole, and cheek were found to be consistently higher than those at scalp, forehead, retroauricular folds, antecubital and popliteal fossae, anterior arm, anterior the mean pH of male skin appeared to be lower than that of female. The highest pH recorded was in axilla (5.98 for male, 6.00 for female, irrespective of sex. The lowest value however was in anterior neck (4.59 for male and in antecubital fossa (4.83 for female. While the origin of the skin pH is yet to be definitely known, it was observed that a high density of both sweat gland and bacteria flora leads to a high pH, and high concentration of sebaceous gland and of bacterial flora to a lower pH.

Examining Summer Laboratory Research Apprenticeships for High School Students as a Factor in Entry to MD/PhD Programs at Matriculation

Science.gov (United States)

Tai, Robert H.; Kong, Xiaoqing; Mitchell, Claire E.; Dabney, Katherine P.; Read, Daniel M.; Jeffe, Donna B.; Andriole, Dorothy A.; Wathington, Heather D.

2017-01-01

Do summer laboratory research apprenticeships during high school have an impact on entry into MD/PhD programs? Apart from the nearly decade-long span of time between high school and matriculation into an MD/PhD program, young people have many life-shaping experiences that presumably impact their education and career trajectories. This quantitative…

pH, Lactate, and Hypoxia: Reciprocity in Regulating High-Affinity Monocarboxylate Transporter Expression in Glioblastoma

Directory of Open Access Journals (Sweden)

James P. Caruso

2017-02-01

Full Text Available Highly malignant brain tumors harbor the aberrant propensity for aerobic glycolysis, the excessive conversion of glucose to lactic acid even in the presence of ample tissue oxygen. Lactic acid is rapidly effluxed to the tumor microenvironment via a group of plasma-membrane transporters denoted monocarboxylate transporters (MCTs to prevent “self-poisoning.” One isoform, MCT2, has the highest affinity for lactate and thus should have the ability to respond to microenvironment conditions such as hypoxia, lactate, and pH to help maintain high glycolytic flux in the tumor. Yet, MCT2 is considered to not respond to hypoxia, which is counterintuitive. Its response to tumor lactate has not been reported. In this report, we experimentally identify the transcription initiation site/s for MCT2 in astrocytes (normal and glioma (tumor. We then use a BACmid library to isolate a 4.2-kbp MCT2 promoter-exon I region and examine promoter response to glycolysis-mediated stimuli in glioma cells. Reporter analysis of nested-promoter constructs indicated response of MCT2 to hypoxia, pH, lactate, and glucose, the major physiological “players” that facilitate a tumor's growth and proliferation. Immunoblot analysis of native MCT2 expression under altered pH and hypoxia reflected the reporter data. The pH-mediated gene-regulation studies we describe are the first to record H+-based reporter studies for any mammalian system and demonstrate the exquisite response of the MCT2 gene to minute changes in tumor pH. Identical promoter usage also provides the first evidence of astrocytes harnessing the same gene regulatory regions to facilitate astrocyte-neuron lactate shuttling, a metabolic feature of normal brain.

Dithiopheneindenofluorene (TIF) Semiconducting Polymers with Very High Mobility in Field-Effect Transistors

KAUST Repository

Chen, Hu

2017-07-19

The charge-carrier mobility of organic semiconducting polymers is known to be enhanced when the energetic disorder of the polymer is minimized. Fused, planar aromatic ring structures contribute to reducing the polymer conformational disorder, as demonstrated by polymers containing the indacenodithiophene (IDT) repeat unit, which have both a low Urbach energy and a high mobility in thin-film-transistor (TFT) devices. Expanding on this design motif, copolymers containing the dithiopheneindenofluorene repeat unit are synthesized, which extends the fused aromatic structure with two additional phenyl rings, further rigidifying the polymer backbone. A range of copolymers are prepared and their electrical properties and thin-film morphology evaluated, with the co-benzothiadiazole polymer having a twofold increase in hole mobility when compared to the IDT analog, reaching values of almost 3 cm2 V−1 s−1 in bottom-gate top-contact organic field-effect transistors.

Corrosion of zirconium alloys in alternating pH environment

International Nuclear Information System (INIS)

Mayer, P.; Manolescu, A.V.

1985-01-01

Behaviour of two commercial alloys, Zircaloy-2 and zirconium-2.5 wt% niobium were investigated in an environment of alternating pH. Corrosion advancement and scale morphology of coupons exposed to aqueous solution of LiOH (pH 10.2 and 14) were followed as a function of temperature (300-360 degreesC) and time (up to 165 days). The test sequence consisted of short term exposure to high pH and re-exposure to low pH solutions for extended period of time followed by a short term test in high pH. The results of these tests and detailed post-corrosion analysis indicate a fundamental difference between the corrosion behaviour of these two materials. Both alloys corrode fast in high pH environments, but only zirconium-2.5 wt% niobium continues to form detectable new oxide in low pH solution

Mobility in the academic careers at the Flemish universities: Results from the Human Resources in Research database

Energy Technology Data Exchange (ETDEWEB)

Debacker, N.; Vandevelde, K.

2016-07-01

Worldwide mobility of researchers is generally correlated with an enhancement of the continuous interchange of ideas and is therefore highly stimulated. Flemish universities have occasionally been criticized for providing limited career opportunities for foreign researchers. However, presently no reliable data is available on researchers’ mobility in Flanders. For the five Flemish universities a full dataset is available at the ECOOM Centre for R&D Monitoring, containing all academic appointments and PhD’s awarded since 1990-1991. This dataset allows for prospective analyses within the Flemish university system as well as retrospective analyses and provides information on international and interuniversity recruitment and academic inbreeding. The present results confirm that the academic system in Flanders is indeed recognized by a tradition of internal recruitment. However specific differences between the universities and the scientific disciplines are observed calling for a more complex study of researchers’ mobility and of the relationship between mobility and research excellence. (Author)

DESIGN APPLICATIONS BASED ON WEB MOBILE AT GAYA BARU SENIOR HIGH SCHOOL, CENTRAL LAMPUNG REGENCY AS PROMOTIONAL MEDIA

Directory of Open Access Journals (Sweden)

Ahmad Yudi

2017-05-01

Full Text Available Gaya Baru Senior High School is one of the educational institutions in Lampung which is a less favorite institution in the area is precisely located in the district of Seputih Surabaya Central Lampung Regency. Gaya Baru Senior High School has already had a website but not many known. This Senior High School is also no information system through mobile web to promote the institution. Nevertheless, in its development, students or community want to find information about the school can be directly through the mobile web application. So in its development requires fast service. From research that conducted in Gaya Baru High School, existence of new mobile web application system will facilitate student or society of that area, especially in subdistrict Seputih Surabaya district Central Lampung, and present information about the info about situation in high school of new style it can be accessed directly through the mobile web media.

Diketopyrrolopyrrole-diketopyrrolopyrrole-based conjugated copolymer for high-mobility organic field-effect transistors

KAUST Repository

Kanimozhi, Catherine K.; Yaacobi-Gross, Nir; Chou, Kang Wei; Amassian, Aram; Anthopoulos, Thomas D.; Patil, Satish P.

2012-01-01

In this communication, we report the synthesis of a novel diketopyrrolopyrrole-diketopyrrolopyrrole (DPP-DPP)-based conjugated copolymer and its application in high-mobility organic field-effect transistors. Copolymerization of DPP with DPP yields a

High electron mobility and quantum oscillations in non-encapsulated ultrathin semiconducting Bi2O2Se

Science.gov (United States)

Wu, Jinxiong; Yuan, Hongtao; Meng, Mengmeng; Chen, Cheng; Sun, Yan; Chen, Zhuoyu; Dang, Wenhui; Tan, Congwei; Liu, Yujing; Yin, Jianbo; Zhou, Yubing; Huang, Shaoyun; Xu, H. Q.; Cui, Yi; Hwang, Harold Y.; Liu, Zhongfan; Chen, Yulin; Yan, Binghai; Peng, Hailin

2017-07-01

High-mobility semiconducting ultrathin films form the basis of modern electronics, and may lead to the scalable fabrication of highly performing devices. Because the ultrathin limit cannot be reached for traditional semiconductors, identifying new two-dimensional materials with both high carrier mobility and a large electronic bandgap is a pivotal goal of fundamental research. However, air-stable ultrathin semiconducting materials with superior performances remain elusive at present. Here, we report ultrathin films of non-encapsulated layered Bi2O2Se, grown by chemical vapour deposition, which demonstrate excellent air stability and high-mobility semiconducting behaviour. We observe bandgap values of ˜0.8 eV, which are strongly dependent on the film thickness due to quantum-confinement effects. An ultrahigh Hall mobility value of >20,000 cm2 V-1 s-1 is measured in as-grown Bi2O2Se nanoflakes at low temperatures. This value is comparable to what is observed in graphene grown by chemical vapour deposition and at the LaAlO3-SrTiO3 interface, making the detection of Shubnikov-de Haas quantum oscillations possible. Top-gated field-effect transistors based on Bi2O2Se crystals down to the bilayer limit exhibit high Hall mobility values (up to 450 cm2 V-1 s-1), large current on/off ratios (>106) and near-ideal subthreshold swing values (˜65 mV dec-1) at room temperature. Our results make Bi2O2Se a promising candidate for future high-speed and low-power electronic applications.

High electron mobility and large magnetoresistance in the half-Heusler semimetal LuPtBi

KAUST Repository

Hou, Zhipeng; Wang, Wenhong; Xu, Guizhou; Zhang, Xiaoming; Wei, Zhiyang; Shen, Shipeng; Liu, Enke; Yao, Yuan; Chai, Yisheng; Sun, Young; Xi, Xuekui; Wang, Wenquan; Liu, Zhongyuan; Wu, Guangheng; Zhang, Xixiang

2015-01-01

Materials with high carrier mobility showing large magnetoresistance (MR) have recently received much attention because of potential applications in future high-performance magnetoelectric devices. Here, we report on an electron-hole

Results of Sludge Mobilization Testing at Hanford High Level Waste (HLW) Tank

International Nuclear Information System (INIS)

STAEHR, T.W.

2001-01-01

Waste stored in the Tank 241-AZ-101 at the US DOE Hanford is scheduled as the initial feed for high-level waste vitrification. Tank 241-AZ-101 currently holds over 3,000,000 liters of waste made up of a settled sludge layer covered by a layer of liquid supernant. To retrieve the waste from the tank, it is necessary to mobilize and suspend the settled sludge so that the resulting slurry can be pumped from the tank for treatment and vitrification. Two 223.8-kilowatt mixer pumps have been installed in Tank 241-AZ-101 to mobilize the settled sludge layer of waste for retrieval. In May of 2000, the mixer pumps were subjected to a series of tests to determine (1) the extent to which the mixer pumps could mobilize the settle sludge layer of waste, (2) if the mixer pumps could function within operating parameters, and (3) if state-of-the-art monitoring equipment could effectively monitor and quantify the degree of sludge mobilization and suspension. This paper presents the major findings and results of the Tank 241-AZ-101 mixer pump tests, based on analysis of data and waste samples that were collected during the testing. Discussion of the results focuses on the effective cleaning radius achieved and the volume and concentration of sludge mobilized, with both one and two pumps operating in various configurations and speeds. The Tank 241-AZ-101 mixer pump tests were unique in that sludge mobilization parameters were measured using actual waste in an underground storage tank at the hanford Site. The methods and instruments that were used to measure waste mobilization parameters in Tank 241-AZ-101 can be used in other tanks. It can be concluded from the testing that the use of mixer pumps is an effective retrieval method for the mobilization of settled solids in Tank 241-AZ-101

Effects of seawater mixing on the mobility of trace elements in acid phosphogypsum leachates.

Science.gov (United States)

Papaslioti, Evgenia-Maria; Pérez-López, Rafael; Parviainen, Annika; Sarmiento, Aguasanta M; Nieto, José M; Marchesi, Claudio; Delgado-Huertas, Antonio; Garrido, Carlos J

2018-02-01

This research reports the effects of pH increase on contaminant mobility in phosphogypsum leachates by seawater mixing, as occurs with dumpings on marine environments. Acid leachates from a phosphogypsum stack located in the Estuary of Huelva (Spain) were mixed with seawater to achieve gradually pH7. Concentrations of Al, Fe, Cr, Pb and U in mixed solutions significantly decreased with increasing pH by sorption and/or precipitation processes. Nevertheless, this study provides insight into the high contribution of the phosphogypsum stack to the release of other toxic elements (Co, Ni, Cu, Zn, As, Cd and Sb) to the coastal areas, as 80-100% of their initial concentrations behaved conservatively in mixing solutions with no participation in sorption processes. Stable isotopes ruled out connexion between different phosphogypsum-related wastewaters and unveiled possible weathering inputs of estuarine waters to the stack. The urgency of adopting effective restoration measures in the study area is also stressed. Copyright © 2018 Elsevier Ltd. All rights reserved.

Effects of flooding on phosphorus and iron mobilization in highly weathered soils: Short-term effects and mechanisms

Science.gov (United States)

Maranguit, Deejay

2017-04-01

The strong affinity of phosphorus (P) to iron (Fe) oxides and hydroxides in highly weathered tropical soils limits P availability and therefore plant productivity. In flooded soils, however, P fixed by Fe oxides and hydroxides can be released and transformed to a more available form because of Fe3+ reduction to Fe2+. These P dynamics in flooded soils are well documented for rice paddies. Such effects are much less studied in other land-use types under the influence of seasonal flooding, especially in the tropics during heavy monsoon rains. The aim of this study was to investigate the mobilization of P during flooding leading to anaerobic conditions in topsoil and subsoil horizons depending on land-use type. Samples were collected in highly weathered soils from four replicate sites under natural rainforest, jungle rubber, rubber and oil palm plantations in Sumatra, Indonesia. Topsoil and subsoil were taken to ensure a wide range of soil organic matter (SOM) and P contents. Soils were incubated under anaerobic, flooded conditions at 30 ± 1 oC for 60 days. Our results confirmed the hypothesis that soil flooding mobilizes P and increases P availability. Two distinct and opposite phases, however, were observed upon flooding. During the first three weeks of flooding, the dissolved P (DP) concentration peaked, simultaneously with a peak of dissolved Fe2+ (DFe2+) and dissolved organic carbon (DOC) in the soil solution. After three weeks, P availability in soils decreased, although Fe-P and available P did not reach initial, pre-flooding levels. Accordingly, Fe dissolution and P mobilization were reversible processes. Furthermore, land-use type influenced the impacts of flooding on P and Fe forms mainly in the topsoil, where P dissolution and availability were generally higher under forest and, to a lesser extent, under jungle rubber. A positive correlation between DOC and DFe2+ (R2 = 0.42) in topsoil indicates that the intensity of microbially-mediated Fe3+ reduction is

High-resolution Imaging of pH in Alkaline Sediments and Water Based on a New Rapid Response Fluorescent Planar Optode

Science.gov (United States)

Han, Chao; Yao, Lei; Xu, Di; Xie, Xianchuan; Zhang, Chaosheng

2016-05-01

A new dual-lumophore optical sensor combined with a robust RGB referencing method was developed for two-dimensional (2D) pH imaging in alkaline sediments and water. The pH sensor film consisted of a proton-permeable polymer (PVC) in which two dyes with different pH sensitivities and emission colors: (1) chloro phenyl imino propenyl aniline (CPIPA) and (2) the coumarin dye Macrolex® fluorescence yellow 10 GN (MFY-10 GN) were entrapped. Calibration experiments revealed the typical sigmoid function and temperature dependencies. This sensor featured high sensitivity and fast response over the alkaline working ranges from pH 7.5 to pH 10.5. Cross-sensitivity towards ionic strength (IS) was found to be negligible for freshwater when IS applications.

High mobility AlGaN/GaN devices for β"−-dosimetry

International Nuclear Information System (INIS)

Schmid, Martin; Howgate, John; Ruehm, Werner; Thalhammer, Stefan

2016-01-01

There is a high demand in modern medical applications for dosimetry sensors with a small footprint allowing for unobtrusive or high spatial resolution detectors. To this end we characterize the sensoric response of radiation resistant high mobility AlGaN/GaN semiconductor devices when exposed to β"−-emitters. The samples were operated as a floating gate transistor, without a field effect gate electrode, thus excluding any spurious effects from β"−-particle interactions with a metallic surface covering. We demonstrate that the source–drain current is modulated in dependence on the kinetic energy of the incident β"−-particles. Here, the signal is shown to have a linear dependence on the absorbed energy calculated from Monte Carlo simulations. Additionally, a stable and reproducible sensor performance as a β"−-dose monitor is shown for individual radioisotopes. Our experimental findings and the characteristics of the AlGaN/GaN high mobility layered devices indicate their potential for future applications where small sensor size is necessary, like for instance brachytherapy.

Hemoadsorption of high-mobility-group box 1 using a porous polymethylmethacrylate fiber in a swine acute liver failure model.

Science.gov (United States)

Amemiya, Ryusuke; Shinoda, Masahiro; Yamada, Masayuki; Ueno, Yoshiyuki; Shimada, Kaoru; Fujieda, Hiroaki; Yagi, Hiroshi; Mizota, Takamasa; Nishiyama, Ryo; Oshima, Go; Yamada, Shingo; Matsubara, Kentaro; Abe, Yuta; Hibi, Taizo; Kitago, Minoru; Obara, Hideaki; Itano, Osamu; Kitagawa, Yuko

2018-04-01

High-mobility-group box chromosomal protein 1 has been identified as an important mediator of various kinds of acute and chronic inflammation. In this study, we aimed to develop a column that effectively adsorbs high-mobility-group box chromosomal protein 1 by altering the pore size of the fiber. First, we produced three types of porous polymethylmethacrylate fiber by altering the concentration of polymethylmethacrylate dissolved in dimethylsulfoxide. We then selected a fiber based on the results of an in vitro incubation test of high-mobility-group box chromosomal protein 1 adsorption. Using the selected fiber, we constructed a new column and tested its high-mobility-group box chromosomal protein 1 adsorption capacity during 4-h extracorporeal hemoperfusion in a swine acute liver failure model. Electron microscope observation showed that the three types of fibers had different pore sizes on the surface and in cross section, which were dependent on the concentration of polymethylmethacrylate. In the in vitro incubation test, fiber with moderate-sized pores demonstrated the highest adsorption capacity. In the in vivo hemoperfusion study, the ratio of the high-mobility-group box chromosomal protein 1 concentration at the outlet versus the inlet of the column was significantly lower with the new column than with the control column during 4-h extracorporeal hemoperfusion. The normalized plasma level of high-mobility-group box chromosomal protein 1 at 12 h after the completion of hemoperfusion was significantly lower with the new column than with the control column. The newly developed polymethylmethacrylate column adsorbs high-mobility-group box chromosomal protein 1 during hemoperfusion in swine ALF model.

Some effects of pH on iodine volatility in containment

International Nuclear Information System (INIS)

Ashmore, C.B.; Gwyther, J.R.; Sims, H.E.

1994-01-01

The behaviour of iodine in containment in the event of an accident involving fission product release would be strongly dependent on pH. High pH leads to a lower rate of radiolytic oxidation and in alkaline conditions the thermally stable form is IO 3 - . Much of the work on effects of pH on radiolytic oxidation reported in the literature may be erroneous or misleading because of postirradiation reaction and in this report some new experiments are described which were designed to overcome these problems involving sparged irradiated solutions of CsI spiked with 131 I. The rate of radiolytic oxidation has been measured as a function of pH between pH 4.6 and pH 9 and iodide concentrations between 10 -4 and 10 -6 mol dm -3 . Also discussed in the paper are factors which can affect the pH of the sump water and the effects of high pH in sprays. It is concluded that high pH is beneficial and it is important not only to achieve high pH but to maintain it. (author). 10 refs., 1 tab., 6 figs

Mobile networks architecture

CERN Document Server

Perez, Andre

2013-01-01

This book explains the evolutions of architecture for mobiles and summarizes the different technologies:- 2G: the GSM (Global System for Mobile) network, the GPRS (General Packet Radio Service) network and the EDGE (Enhanced Data for Global Evolution) evolution;- 3G: the UMTS (Universal Mobile Telecommunications System) network and the HSPA (High Speed Packet Access) evolutions:- HSDPA (High Speed Downlink Packet Access),- HSUPA (High Speed Uplink Packet Access),- HSPA+;- 4G: the EPS (Evolved Packet System) network.The telephone service and data transmission are the

In situ electrochemical enrichment and isolation of a magnetite-reducing bacterium from a high pH serpentinizing spring.

Science.gov (United States)

Rowe, Annette R; Yoshimura, Miho; LaRowe, Doug E; Bird, Lina J; Amend, Jan P; Hashimoto, Kazuhito; Nealson, Kenneth H; Okamoto, Akihiro

2017-06-01

Serpentinization is a geologic process that produces highly reduced, hydrogen-rich fluids that support microbial communities under high pH conditions. We investigated the activity of microbes capable of extracellular electron transfer in a terrestrial serpentinizing system known as 'The Cedars'. Measuring current generation with an on-site two-electrode system, we observed daily oscillations in current with the current maxima and minima occurring during daylight hours. Distinct members of the microbial community were enriched. Current generation in lab-scale electrochemical reactors did not oscillate, but was correlated with carbohydrate amendment in Cedars-specific minimal media. Gammaproteobacteria and Firmicutes were consistently enriched from lab electrochemical systems on δ-MnO 2 and amorphous Fe(OH) 3 at pH 11. However, isolation of an electrogenic strain proved difficult as transfer cultures failed to grow after multiple rounds of media transfer. Lowering the bulk pH in the media allowed us to isolate a Firmicutes strain (Paenibacillus sp.). This strain was capable of electrode and mineral reduction (including magnetite) at pH 9. This report provides evidence of the in situ activity of microbes using extracellular substrates as sinks for electrons at The Cedars, but also highlights the potential importance of community dynamics for supporting microbial life through either carbon fixation, and/or moderating pH stress. © 2017 The Authors. Environmental Microbiology published by Society for Applied Microbiology and John Wiley & Sons Ltd.

Chelant-aided enhancement of lead mobilization in residential soils

International Nuclear Information System (INIS)

Sarkar, Dibyendu; Andra, Syam S.; Saminathan, Sumathi K.M.; Datta, Rupali

2008-01-01

Chelation of metals is an important factor in enhancing solubility and hence, availability to plants to promote phytoremediation. We compared the effects of two chelants, namely, ethylenediaminetetraacetic acid (EDTA) and ethylenediaminedisuccinic acid (EDDS) in enhancing mobilized lead (Pb) in Pb-based paint contaminated residential soils collected from San Antonio, Texas and Baltimore, Maryland. Batch incubation studies were performed to investigate the effectiveness of the two chelants in enhancing mobilized Pb, at various concentrations and treatment durations. Over a period of 1 month, the mobilized Pb pool in the San Antonio study soils increased from 52 mg kg -1 to 287 and 114 mg kg -1 in the presence of 15 mM kg -1 EDTA and EDDS, respectively. Stepwise linear regression analysis demonstrated that pH and organic matter content significantly affected the mobilized Pb fraction. The regression models explained a large percentage, from 83 to 99%, of the total variation in mobilized Pb concentrations. - Complexation by a biodegradable chelating agent, EDDS enhances mobilized Pb concentrations in Pb-paint contaminated residential soils

The GalileoMobile Project

Science.gov (United States)

Del Pilar Becerra, A.&ída; Bhatt, Megha; Kobel, Philippe

2012-07-01

GalileoMobile is a traveling science education project by an international team of PhD students and recent graduates (partnering with the Universe Awareness program) that brings astronomy to young people in remote regions of developing countries. Our primary project goals are: (1) to stimulate students' curiosity and interest in learning, (2) to exchange different visions of the cosmos and cultures, and (3) to inspire a feeling of unity "under the same sky" between people from different parts of the world. In 2009, GalileoMobile traveled to 30 schools in Chile, Bolivia and Peru, bringing hands-on activities and Galileoscopes; the team also produced a documentary movie to share the experiences and culture with the world. In 2012, GalileoMobile plans an expedition to India from the 2nd to the 13th of July in villages between Bangalore and Mysore. We will again bring hands-on astronomy activities and telescopes to the schools, and share our experiences with the world via internet resources. GalileoMobile is also collaborating with the Galileo Teacher Training Program to provide workshops for local teachers, to encourage continuation of astronomy education beyond our visit. In this way, we expect to spark sustainable interest in astronomy in remote areas that have little access to science outreach, and to share the culture of these areas with the world -- "under the same sky."

Followup Audit: DLA Officials Took Appropriate Actions to Address Concerns With Repair Parts for the High Mobility Multipurpose Wheeled Vehicle

Science.gov (United States)

2016-04-29

Followup Audit : DLA Officials Took Appropriate Actions to Address Concerns With Repair Parts for the High Mobility Multipurpose Wheeled Vehicle A P R I L...Results in Brief Followup Audit : DLA Officials Took Appropriate Actions to Address Concerns With Repair Parts for the High Mobility Multipurpose Wheeled...and Maritime Paid Too Much for High Mobility Multipurpose Wheeled Vehicle Repair Parts,” (HMMWV) was issued on April 4, 2014. The audit

Crystal Structure and Superconductivity of PH ₃ at High Pressures

Energy Technology Data Exchange (ETDEWEB)

Liu, Hanyu [Geophysical; Department; Li, Yinwei [School; Gao, Guoying [State; Tse, John S. [Department; State; Naumov, Ivan I. [Geophysical

2016-02-04

We have performed a systematic structure search on solid PH3 at high pressures using the particle swarm optimization method. At 100–200 GPa, the search led to two structures which along with others have P–P bonds. These structures are structurally and chemically distinct from those predicted for the high-pressure superconducting H2S phase, which has a different topology (i.e., does not contain S–S bonds). Phonon and electron–phonon coupling calculations indicate that both structures are dynamically stable and superconducting. The pressure dependence and critical temperature for the monoclinic (C2/m) phase of 83 K at 200 GPa are in excellent agreement with a recent experimental report.

Effect of leachate of cementitious materials on the geological media. Experimental study of the influence of high pH plume on rock

International Nuclear Information System (INIS)

Kato, Hiroshige; Sato, Mitsuyoshi; Owada, Hitoshi; Mihara, Morihiro; Ohi, Takao

2000-05-01

Cementitious materials will be used in TRU waste disposal repository. In such cases, it is considered that the migration of alkaline leachates from cementitious materials, so called high pH plume, will cause dissolution of rock and precipitation of secondary minerals. In addition, the high pH plume will move along the flow of groundwater, so it is predicted that rock formation and components of high pH groundwater vary with time and space. However, time and spatial dependence of the variations of secondary minerals and groundwater components has not been clarified. In order to acquire the data of variations of secondary minerals and groundwater components, we carried out the rock alteration experiments with column method. The crushed granodiorite was filled into 4 meters length column (φ 3.7 cm) and artificial cement leachate (pH=13.3; Na=0.1mol/l, K=0.1mol/l, Ca=0.002mol/l) was streamed at flow rates of 0.1 ml/min for 7 months at 80degC. As the result, secondary minerals confirmed on the rock were calcite and C-S-H at upstream of column and C-S-H at mid-downstream. The pH value of the fluid dominated by Na and K did not be decreased by reaction with the rock. In this study, the data relating to the effect of high pH plume on rock over the long term was acquired. (author)

PhD on Track – designing learning for PhD students

Directory of Open Access Journals (Sweden)

Gunhild Austrheim

2013-12-01

proved a challenge for the production team. How do you illustrate copyright or the process of getting published? The project team sees user testing as an essential part of content development. Though PhD on Track certainly mirrors the research support efforts of the academic libraries behind it, by involving the users throughout the production we have tried to make sure it is a highly relevant and qualitatively sound resource for the PhD students. "Information Management for Knowledge Creation" is a collaborative project ran by the libraries at the Bergen University College, the Norwegian School of Economics, and at the Universities of Bergen, Oslo and Aalborg. The project is funded by the Norwegian National Library.

Effects of phytoextraction on heavy metal concentrations and pH of pore-water of biosolids determined using an in situ sampling technique.

Science.gov (United States)

Huynh, T T; Laidlaw, W S; Singh, B; Gregory, D; Baker, A J M

2008-12-01

Heavy metal concentrations and pH of pore-water in contaminated substrates are important factors in controlling metal uptake by plants. We investigated the effects of phytoextraction on these properties in the solution phase of biosolids and diluted biosolids in a 12-month phytoextraction column experiment. Phytoextraction using Salix and Populus spp. temporarily decreased pore-water pH of the substrates over the experimental period followed by a return to initial pH conditions. Salixxreichardtii and Populus balsamifera effectively extracted Ni, Zn and Cd and actively mobilized these metals from the solid to the solution phase. S.xreichardtii had the stronger effect on mobilization of metals due to its larger root system. Phytoextraction did not affect Cu in the solution phase of the biosolids. Heavy metals were leached down to lower depths of the columns during the phytoextraction process.

Graphene/Pentacene Barristor with Ion-Gel Gate Dielectric: Flexible Ambipolar Transistor with High Mobility and On/Off Ratio.

Science.gov (United States)

Oh, Gwangtaek; Kim, Jin-Soo; Jeon, Ji Hoon; Won, EunA; Son, Jong Wan; Lee, Duk Hyun; Kim, Cheol Kyeom; Jang, Jingon; Lee, Takhee; Park, Bae Ho

2015-07-28

High-quality channel layer is required for next-generation flexible electronic devices. Graphene is a good candidate due to its high carrier mobility and unique ambipolar transport characteristics but typically shows a low on/off ratio caused by gapless band structure. Popularly investigated organic semiconductors, such as pentacene, suffer from poor carrier mobility. Here, we propose a graphene/pentacene channel layer with high-k ion-gel gate dielectric. The graphene/pentacene device shows both high on/off ratio and carrier mobility as well as excellent mechanical flexibility. Most importantly, it reveals ambipolar behaviors and related negative differential resistance, which are controlled by external bias. Therefore, our graphene/pentacene barristor with ion-gel gate dielectric can offer various flexible device applications with high performances.

Enhanced hydrogen evolution rates at high pH with a colloidal cadmium sulphide–platinum hybrid system

International Nuclear Information System (INIS)

Schneider, Julian; Vaneski, Aleksandar; Susha, Andrei S.; Rogach, Andrey L.; Pesch, Georg R.; Yang Teoh, Wey

2014-01-01

We demonstrate enhanced hydrogen generation rates at high pH using colloidal cadmium sulphide nanorods decorated with Pt nanoparticles. We introduce a simplified procedure for the decoration and subsequent hydrogen generation, reducing both the number of working steps and the materials costs. Different Pt precursor concentrations were tested to reveal the optimal conditions for the efficient hydrogen evolution. A sharp increase in hydrogen evolution rates was measured at pH 13 and above, a condition at which the surface charge transfer was efficiently mediated by the formation of hydroxyl radicals and further consumption by the sacrificial triethanolamine hole scavenger

Enhanced hydrogen evolution rates at high pH with a colloidal cadmium sulphide–platinum hybrid system

Energy Technology Data Exchange (ETDEWEB)

Schneider, Julian; Vaneski, Aleksandar; Susha, Andrei S.; Rogach, Andrey L., E-mail: andrey.rogach@cityu.edu.hk [Department of Physics and Materials Science and Centre for Functional Photonics (CFP), City University of Hong Kong, 83 Tat Chee Avenue, Kowloon (Hong Kong); Pesch, Georg R.; Yang Teoh, Wey [Clean Energy and Nanotechnology (CLEAN) Laboratory, School of Energy and Environment, City University of Hong Kong, 83 Tat Chee Avenue, Kowloon (Hong Kong)

2014-12-01

We demonstrate enhanced hydrogen generation rates at high pH using colloidal cadmium sulphide nanorods decorated with Pt nanoparticles. We introduce a simplified procedure for the decoration and subsequent hydrogen generation, reducing both the number of working steps and the materials costs. Different Pt precursor concentrations were tested to reveal the optimal conditions for the efficient hydrogen evolution. A sharp increase in hydrogen evolution rates was measured at pH 13 and above, a condition at which the surface charge transfer was efficiently mediated by the formation of hydroxyl radicals and further consumption by the sacrificial triethanolamine hole scavenger.

Mobility and retention of micronutrients in soil : Part III. Investigation on the influence of various external factors, NPK-fertilizers and soil amending agents on the mobility and retention of manganese

International Nuclear Information System (INIS)

Das, S.K.; Santikari, A.K.; Banerji, K.C.

1980-01-01

Investigations on the mobility and retention of manganese through Sindri red sandy clay loam of pH 7.4 and Ranchi clay loam of pH 5.6 have been carried out using the radiotracer 54 Mn. The vertical distribution of manganese in these soils showed almost sharp fall upto a depth of 12 to 14 cm and thereafter it tended to attain the saturation. Variations have been marked in the degrees of manganese retention at the top surface layers of the concerned soils. Influence of various NPK fertilizers and soil amending agents, at various application levels, have been studied on the mobility, retention and leaching loss of manganese in the prementioned soils. Marked variations have been recorded and discussed. (author)

Thermoelectric transport properties of high mobility organic semiconductors

Science.gov (United States)

Venkateshvaran, Deepak; Broch, Katharina; Warwick, Chris N.; Sirringhaus, Henning

2016-09-01

Transport in organic semiconductors has traditionally been investigated using measurements of the temperature and gate voltage dependent mobility of charge carriers within the channel of organic field-effect transistors (OFETs). In such measurements, the behavior of charge carrier mobility with temperature and gate voltage, studied together with carrier activation energies, provide a metric to quantify the extent of disorder within these van der Waals bonded materials. In addition to the mobility and activation energy, another potent but often-overlooked transport coefficient useful in understanding disorder is the Seebeck coefficient (also known as thermoelectric power). Fundamentally, the Seebeck coefficient represents the entropy per charge carrier in the solid state, and thus proves powerful in distinguishing materials in which charge carriers move freely from those where a high degree of disorder causes the induced carriers to remain trapped. This paper briefly covers the recent highlights in the field of organic thermoelectrics, showing how significant strides have been made both from an applied standpoint as well as from a viewpoint of fundamental thermoelectric transport physics. It shall be illustrated how thermoelectric transport parameters in organic semiconductors can be tuned over a significant range, and how this tunability facilitates an enhanced performance for heat-to-electricity conversion as well as quantifies energetic disorder and the nature of the density of states (DOS). The work of the authors shall be spotlighted in this context, illustrating how Seebeck coefficient measurements in the polymer indacenodithiophene-co-benzothiadiazole (IDTBT) known for its ultra-low degree of torsion within the polymer backbone, has a trend consistent with low disorder. 1 Finally, using examples of the small molecules C8-BTBT and C10-DNTT, it shall be discussed how the Seebeck coefficient can aid the estimation of the density and distribution of trap states

Mapping Oyster Reef Habitats in Mobile Bay

Science.gov (United States)

Bolte, Danielle

2011-01-01

Oyster reefs around the world are declining rapidly, and although they haven t received as much attention as coral reefs, they are just as important to their local ecosystems and economies. Oyster reefs provide habitats for many species of fish, invertebrates, and crustaceans, as well as the next generations of oysters. Oysters are also harvested from many of these reefs and are an important segment of many local economies, including that of Mobile Bay, where oysters rank in the top five commercial marine species both by landed weight and by dollar value. Although the remaining Mobile Bay oyster reefs are some of the least degraded in the world, projected climate change could have dramatic effects on the health of these important ecosystems. The viability of oyster reefs depends on water depth and temperature, appropriate pH and salinity levels, and the amount of dissolved oxygen in the water. Projected increases in sea level, changes in precipitation and runoff patterns, and changes in pH resulting from increases in the amount of carbon dioxide dissolved in the oceans could all affect the viability of oyster reefs in the future. Human activities such as dredging and unsustainable harvesting practices are also adversely impacting the oyster reefs. Fortunately, several projects are already under way to help rebuild or support existing or previously existing oyster reefs. The success of these projects will depend on the local effects of climate change on the current and potential habitats and man s ability to recognize and halt unsustainable harvesting practices. As the extent and health of the reefs changes, it will have impacts on the Mobile Bay ecosystem and economy, changing the resources available to the people who live there and to the rest of the country, since Mobile Bay is an important national source of seafood. This project identified potential climate change impacts on the oyster reefs of Mobile Bay, including the possible addition of newly viable

An Investigation of the Relationship between High-School Students' Problematic Mobile Phone Use and Their Self-Esteem Levels

Science.gov (United States)

Isiklar, Abdullah; Sar, Ali Haydar; Durmuscelebi, Mustafa

2013-01-01

Excessive mobile phone use, especially among adolescents, brings too many debates about its effects. To this end, in this study, we try to investigate the relationship between adolescents' mobile phone use and their self-esteem levels with regard to their genders. For 919 high school students, we evaluated mobile phone use concerning their…

Wide-bandgap high-mobility ZnO thin-film transistors produced at room temperature

International Nuclear Information System (INIS)

Fortunato, Elvira M.C.; Barquinha, Pedro M.C.; Pimentel, Ana C.M.B.G.; Goncalves, Alexandra M.F.; Marques, Antonio J.S.; Martins, Rodrigo F.P.; Pereira, Luis M.N.

2004-01-01

We report high-performance ZnO thin-film transistor (ZnO-TFT) fabricated by rf magnetron sputtering at room temperature with a bottom gate configuration. The ZnO-TFT operates in the enhancement mode with a threshold voltage of 19 V, a saturation mobility of 27 cm 2 /V s, a gate voltage swing of 1.39 V/decade and an on/off ratio of 3x10 5 . The ZnO-TFT presents an average optical transmission (including the glass substrate) of 80% in the visible part of the spectrum. The combination of transparency, high mobility, and room-temperature processing makes the ZnO-TFT a very promising low-cost optoelectronic device for the next generation of invisible and flexible electronics

Local imaging of high mobility two-dimensional electron systems with virtual scanning tunneling microscopy

Energy Technology Data Exchange (ETDEWEB)

Pelliccione, M. [Department of Applied Physics, Stanford University, 348 Via Pueblo Mall, Stanford, California 94305 (United States); Stanford Institute for Materials and Energy Sciences, SLAC National Accelerator Laboratory, 2575 Sand Hill Road, Menlo Park, California 94025 (United States); Department of Physics, University of California, Santa Barbara, Santa Barbara, California 93106 (United States); Bartel, J.; Goldhaber-Gordon, D. [Stanford Institute for Materials and Energy Sciences, SLAC National Accelerator Laboratory, 2575 Sand Hill Road, Menlo Park, California 94025 (United States); Department of Physics, Stanford University, 382 Via Pueblo Mall, Stanford, California 94305 (United States); Sciambi, A. [Department of Applied Physics, Stanford University, 348 Via Pueblo Mall, Stanford, California 94305 (United States); Stanford Institute for Materials and Energy Sciences, SLAC National Accelerator Laboratory, 2575 Sand Hill Road, Menlo Park, California 94025 (United States); Pfeiffer, L. N.; West, K. W. [Department of Electrical Engineering, Princeton University, Princeton, New Jersey 08544 (United States)

2014-11-03

Correlated electron states in high mobility two-dimensional electron systems (2DESs), including charge density waves and microemulsion phases intermediate between a Fermi liquid and Wigner crystal, are predicted to exhibit complex local charge order. Existing experimental studies, however, have mainly probed these systems at micron to millimeter scales rather than directly mapping spatial organization. Scanning probes should be well-suited to study the spatial structure of these states, but high mobility 2DESs are found at buried semiconductor interfaces, beyond the reach of conventional scanning tunneling microscopy. Scanning techniques based on electrostatic coupling to the 2DES deliver important insights, but generally with resolution limited by the depth of the 2DES. In this letter, we present our progress in developing a technique called “virtual scanning tunneling microscopy” that allows local tunneling into a high mobility 2DES. Using a specially designed bilayer GaAs/AlGaAs heterostructure where the tunnel coupling between two separate 2DESs is tunable via electrostatic gating, combined with a scanning gate, we show that the local tunneling can be controlled with sub-250 nm resolution.

Dietary differentiation and the evolution of population genetic structure in a highly mobile carnivore.

Directory of Open Access Journals (Sweden)

Małgorzata Pilot

Full Text Available Recent studies on highly mobile carnivores revealed cryptic population genetic structures correlated to transitions in habitat types and prey species composition. This led to the hypothesis that natal-habitat-biased dispersal may be responsible for generating population genetic structure. However, direct evidence for the concordant ecological and genetic differentiation between populations of highly mobile mammals is rare. To address this we analyzed stable isotope profiles (δ(13C and δ(15N values for Eastern European wolves (Canis lupus as a quantifiable proxy measure of diet for individuals that had been genotyped in an earlier study (showing cryptic genetic structure, to provide a quantitative assessment of the relationship between individual foraging behavior and genotype. We found a significant correlation between genetic distances and dietary differentiation (explaining 46% of the variation in both the marginal test and crucially, when geographic distance was accounted for as a co-variable. These results, interpreted in the context of other possible mechanisms such as allopatry and isolation by distance, reinforce earlier studies suggesting that diet and associated habitat choice are influencing the structuring of populations in highly mobile carnivores.

Correlation Between Two-Dimensional Electron Gas Mobility and Crystal Quality in AlGaN/GaN High-Electron-Mobility Transistor Structure Grown on 4H-SiC.

Science.gov (United States)

Heo, Cheon; Jang, Jongjin; Lee, Kyngjae; So, Byungchan; Lee, Kyungbae; Ko, Kwangse; Nam, Okhyun

2017-01-01

We investigated the correlation between the crystal quality and two-dimensional electron gas (2DEG) mobility of an AlGaN/GaN high-electron-mobility transistor (HEMT) structure grown by metal-organic chemical vapor deposition. For the structure with an AlN nucleation layer grown at 1100 °C, the 2DEG mobility and sheet carrier density were 1627 cm²/V·s and 3.23 × 10¹³ cm⁻², respectively, at room temperature. Further, it was confirmed that the edge dislocation density of the GaN buffer layer was related to the 2DEG mobility and sheet carrier density in the AlGaN/GaN HEMT.

Microbial communities in low permeability, high pH uranium mine tailings: characterization and potential effects.

Science.gov (United States)

Bondici, V F; Lawrence, J R; Khan, N H; Hill, J E; Yergeau, E; Wolfaardt, G M; Warner, J; Korber, D R

2013-06-01

To describe the diversity and metabolic potential of microbial communities in uranium mine tailings characterized by high pH, high metal concentration and low permeability. To assess microbial diversity and their potential to influence the geochemistry of uranium mine tailings using aerobic and anaerobic culture-based methods, in conjunction with next generation sequencing and clone library sequencing targeting two universal bacterial markers (the 16S rRNA and cpn60 genes). Growth assays revealed that 69% of the 59 distinct culturable isolates evaluated were multiple-metal resistant, with 15% exhibiting dual-metal hypertolerance. There was a moderately positive correlation coefficient (R = 0·43, P tailings depth was shown to influence bacterial community composition, with the difference in the microbial diversity of the upper (0-20 m) and middle (20-40 m) tailings zones being highly significant (P tailings zone being significant (P tailings environment, along with their demonstrated capacity for transforming metal elements, suggests that these organisms have the potential to influence the long-term geochemistry of the tailings. This study is the first investigation of the diversity and functional potential of micro-organisms present in low permeability, high pH uranium mine tailings. © 2013 The Society for Applied Microbiology.

High performance flexible pH sensor based on polyaniline nanopillar array electrode.

Science.gov (United States)

Yoon, Jo Hee; Hong, Seok Bok; Yun, Seok-Oh; Lee, Seok Jae; Lee, Tae Jae; Lee, Kyoung G; Choi, Bong Gill

2017-03-15

Flexible pH sensor technologies have attracted a great deal of attention in many applications, such as, wearable health care devices and monitors for chemical and biological processes. Here, we fabricated flexible and thin pH sensors using a two electrode configuration comprised of a polyaniline nanopillar (PAN) array working electrode and an Ag/AgCl reference electrode. In order to provide nanostructure, soft lithography using a polymeric blend was employed to create a flexible nanopillar backbone film. Polyaniline-sensing materials were deposited on a patterned-nanopillar array by electrochemical deposition. The pH sensors produced exhibited a near-Nernstian response (∼60.3mV/pH), which was maintained in a bent state. In addition, pH sensors showed other excellent sensor performances in terms of response time, reversibility, repeatability, selectivity, and stability. Copyright © 2016 Elsevier Inc. All rights reserved.

Mobility and attenuation of arsenic in sulfide-rich mining wastes from the Czech Republic

Energy Technology Data Exchange (ETDEWEB)

Drahota, Petr, E-mail: petr.drahota@natur.cuni.cz [Institute of Geochemistry, Mineralogy and Mineral Resources, Faculty of Science, Charles University, Albertov 6, 128 43 Prague 2 (Czech Republic); Knappová, Magdaléna; Kindlová, Helena; Culka, Adam [Institute of Geochemistry, Mineralogy and Mineral Resources, Faculty of Science, Charles University, Albertov 6, 128 43 Prague 2 (Czech Republic); Majzlan, Juraj [Institute of Geosciences, Friedrich-Schiller University, Burgweg 11, D-07749 Jena (Germany); Mihaljevič, Martin [Institute of Geochemistry, Mineralogy and Mineral Resources, Faculty of Science, Charles University, Albertov 6, 128 43 Prague 2 (Czech Republic); Rohovec, Jan [Institute of Geology, The Czech Academy of Sciences, v.v.i., Rozvojová 269, 165 00 Prague 6 (Czech Republic); Veselovský, František [Czech Geological Survey, Geologická 6, 152 00 Prague 5 (Czech Republic); Fridrichová, Michaela [Institute of Geology, The Czech Academy of Sciences, v.v.i., Rozvojová 269, 165 00 Prague 6 (Czech Republic); Jehlička, Jan [Institute of Geochemistry, Mineralogy and Mineral Resources, Faculty of Science, Charles University, Albertov 6, 128 43 Prague 2 (Czech Republic)

2016-07-01

The mineralogical composition of mining wastes deposited in countless dumps around the world is the key factor that controls retention and release of pollutants. Here we report a multi-method data set combining mineralogical (X-ray diffraction, electron microprobe and Raman microspectrometry) and geochemical (sequential extraction and pore water analysis) methods to resolve As mobility in two 50-years-old mining waste dumps. Originally, all of the As in the mining wastes selected for the study was present as arsenopyrite and with time it has been replaced by secondary As phases. At Jedová jáma mining area, the most of As precipitated as X-ray amorphous ferric arsenate (HFA). Arsenic is also accumulated in the scorodite and Fe (hydr)oxide (with up to 3.2 wt.% As{sub 2}O{sub 5}) that is particularly represented by hematite. Mining wastes at Dlouhá Ves contain only trace amount of scorodite. Arsenic is primarily bound to Pb-jarosite and Fe (hydr)oxides (especially goethite) with up to 1.6 and 1.8 wt.% As{sub 2}O{sub 5}, respectively. The pore water collected after rainfall events indicated high concentrations of As (~ 4600 μg·L{sup −1}) at Jedová jáma, whereas aqueous As at Dlouhá Ves was negligible (up to 1.5 μg·L{sup −1}). Highly mobile As at Jedová jáma is attributed to the dissolution of HFA and simultaneous precipitation of Fe (hydr)oxides under mildly acidic conditions (pH ~ 4.4); immobile As at Dlouhá Ves is due to the efficient adsorption on the Fe (hydr)oxides and hydroxosulfates under acidic pH of ~ 2.8. Taken together, As mobility in the ferric arsenates-containing mining wastes may significantly vary. These wastes must be kept under acidic conditions or with high aqueous Fe(III) concentrations to prevent the release of As from incongruent dissolution of ferric arsenates. - Highlights: • Two 50 years-old sulfide-rich mining waste dumps were studied. • Environmental stability of secondary arsenic mineral phases were assessed. �

Mobility and attenuation of arsenic in sulfide-rich mining wastes from the Czech Republic

International Nuclear Information System (INIS)

Drahota, Petr; Knappová, Magdaléna; Kindlová, Helena; Culka, Adam; Majzlan, Juraj; Mihaljevič, Martin; Rohovec, Jan; Veselovský, František; Fridrichová, Michaela; Jehlička, Jan

2016-01-01

The mineralogical composition of mining wastes deposited in countless dumps around the world is the key factor that controls retention and release of pollutants. Here we report a multi-method data set combining mineralogical (X-ray diffraction, electron microprobe and Raman microspectrometry) and geochemical (sequential extraction and pore water analysis) methods to resolve As mobility in two 50-years-old mining waste dumps. Originally, all of the As in the mining wastes selected for the study was present as arsenopyrite and with time it has been replaced by secondary As phases. At Jedová jáma mining area, the most of As precipitated as X-ray amorphous ferric arsenate (HFA). Arsenic is also accumulated in the scorodite and Fe (hydr)oxide (with up to 3.2 wt.% As_2O_5) that is particularly represented by hematite. Mining wastes at Dlouhá Ves contain only trace amount of scorodite. Arsenic is primarily bound to Pb-jarosite and Fe (hydr)oxides (especially goethite) with up to 1.6 and 1.8 wt.% As_2O_5, respectively. The pore water collected after rainfall events indicated high concentrations of As (~ 4600 μg·L"−"1) at Jedová jáma, whereas aqueous As at Dlouhá Ves was negligible (up to 1.5 μg·L"−"1). Highly mobile As at Jedová jáma is attributed to the dissolution of HFA and simultaneous precipitation of Fe (hydr)oxides under mildly acidic conditions (pH ~ 4.4); immobile As at Dlouhá Ves is due to the efficient adsorption on the Fe (hydr)oxides and hydroxosulfates under acidic pH of ~ 2.8. Taken together, As mobility in the ferric arsenates-containing mining wastes may significantly vary. These wastes must be kept under acidic conditions or with high aqueous Fe(III) concentrations to prevent the release of As from incongruent dissolution of ferric arsenates. - Highlights: • Two 50 years-old sulfide-rich mining waste dumps were studied. • Environmental stability of secondary arsenic mineral phases were assessed. • Different modes of As binding are

Two-Dimensional Modeling of Aluminum Gallium Nitride/Gallium Nitride High Electron Mobility Transistor

National Research Council Canada - National Science Library

Holmes, Kenneth

2002-01-01

Gallium Nitride (GaN) High Electron Mobility Transistors (HEMT's) are microwave power devices that have the performance characteristics to improve the capabilities of current and future Navy radar and communication systems...

Some processes affecting the mobility of thorium in natural ground waters

International Nuclear Information System (INIS)

Oesthols, E.

1994-04-01

Thorium is a useful model element for tetravalent actinides such as U(IV), Pu(IV) and Np(IV) which are important constituents of spent nuclear fuel. Thorium is also an important tracer element for particle pathways in natural environments. In order to correctly model the transport of Th in the environment, it is important to have quantitative models for processes that effect its mobility. Some of these processes have been experimentally investigated in laboratory studies, and interpreted with quantitative models where possible. The carbonate complexation in aqueous solution of Th has been investigated through solubility studies of ThO 2 in carbonate media. It is shown, that thorium carbonate complexes are likely to be predominant in many natural waters. They also increase solubility of the oxide significantly, and hence the mobility of Th. Carbonate also increases the dissolution rate of thorium oxide. This effect will only be important in environments with a pH and total carbonate alkalinity higher than those of most natural aquatic environments. Solubility studies of thorium oxide in phosphate media show that phosphate does not significantly increase the mobility of Th in aqueous media. The presence of phosphate may cause the precipitation of sparingly soluble thorium phosphates which will decrease the mobility of Th. The pentahydroxo complex for Th is shown to be significant up to pH 13. Potentiometric studies of Th sorption on amorphous colloidal silica indicate, that pure aluminosilicates will probably not be efficient scavengers of tetravalent actinides above pH values of approximately 6. In neutral to alkaline solutions, iron (hydr)oxides are likely to be the predominant sorbents. Th binds to the silica surface through corner-sharing bonds, where Th and Si share one, but not more oxygen atoms. 72 refs

Advertising on mobile applications

OpenAIRE

Sobolevsky, Alexandr

2015-01-01

The article analyzes the new method of mobile advertising. Advertising in mobile applications - a subspecies of mobile marketing, where advertising is distributed using mobile phones and smartphones. Ad placement is going on inside of applications and games for smartphones. It has a high potential due to the large number of mobile phone users (over 6.5 billion in 2013).

High Temperature Terahertz Detectors Realized by a GaN High Electron Mobility Transistor

Science.gov (United States)

Hou, H. W.; Liu, Z.; Teng, J. H.; Palacios, T.; Chua, S. J.

2017-04-01

In this work, a high temperature THz detector based on a GaN high electron mobility transistor (HEMT) with nano antenna structures was fabricated and demonstrated to be able to work up to 200 °C. The THz responsivity and noise equivalent power (NEP) of the device were characterized at 0.14 THz radiation over a wide temperature range from room temperature to 200 °C. A high responsivity Rv of 15.5 and 2.7 kV/W and a low NEP of 0.58 and 10 pW/Hz0.5 were obtained at room temperature and 200 °C, respectively. The advantages of the GaN HEMT over other types of field effect transistors for high temperature terahertz detection are discussed. The physical mechanisms responsible for the temperature dependence of the responsivity and NEP of the GaN HEMT are also analyzed thoroughly.

Carbon doped GaAs/AlGaAs heterostructures with high mobility two dimensional hole gas

Energy Technology Data Exchange (ETDEWEB)

Hirmer, Marika; Bougeard, Dominique; Schuh, Dieter [Institut fuer Experimentelle und Angewandte Physik, Universitaet Regensburg, D 93040 Regensburg (Germany); Wegscheider, Werner [Laboratorium fuer Festkoerperphysik, ETH Zuerich, 8093 Zuerich (Switzerland)

2011-07-01

Two dimensional hole gases (2DHG) with high carrier mobilities are required for both fundamental research and possible future ultrafast spintronic devices. Here, two different types of GaAs/AlGaAs heterostructures hosting a 2DHG were investigated. The first structure is a GaAs QW embedded in AlGaAs barrier grown by molecular beam epitaxy with carbon-doping only at one side of the quantum well (QW) (single side doped, ssd), while the second structure is similar but with symmetrically arranged doping layers on both sides of the QW (double side doped, dsd). The ssd-structure shows hole mobilities up to 1.2*10{sup 6} cm{sup 2}/Vs which are achieved after illumination. In contrast, the dsd-structure hosts a 2DHG with mobility up to 2.05*10{sup 6} cm{sup 2}/Vs. Here, carrier mobility and carrier density is not affected by illuminating the sample. Both samples showed distinct Shubnikov-de-Haas oscillations and fractional quantum-Hall-plateaus in magnetotransport experiments done at 20mK, indicating the high quality of the material. In addition, the influence of different temperature profiles during growth and the influence of the Al content of the barrier Al{sub x}Ga{sub 1-x}As on carrier concentration and mobility were investigated and are presented here.

Pasteurization of fruit juices of different pH values by combined high hydrostatic pressure and carbon dioxide.

Science.gov (United States)

Li, Wang; Pan, Jian; Xie, Huiming; Yang, Yi; Zhou, Dianfei; Zhu, Zhaona

2012-10-01

The inactivation of the selected vegetative bacteria Escherichia coli, Listeria innocua, and Lactobacillus plantarum by high hydrostatic pressure (HHP) in physiological saline (PS) and in four fruit juices with pHs ranging from 3.4 to 6.3, with or without dissolved CO(2), was investigated. The inactivation effect of HHP on the bacteria was greatly enhanced by dissolved CO(2). Effective inactivation (>7 log) was achieved at 250 MPa for E. coli and 350 MPa for L. innocua and L. plantarum in the presence of 0.2 M CO(2) at room temperature for 15 min in PS, with additional inactivation of more than 4 log for all three bacteria species compared with the results with HHP treatment alone. The combined inactivation by HHP and CO(2) in tomato juice of pH 4.2 and carrot juice of pH 6.3 showed minor differences compared with that in PS. By comparison, the combined effect in orange juice of pH 3.8 was considerably promoted, while the HHP inactivation was enhanced only to a limited extent. In another orange juice with a pH of 3.4, all three strains lost their pressure resistance. HHP alone completely inactivated E. coli at relatively mild pressures of 200 MPa and L. innocua and L. plantarum at 300 MPa. Observations of the survival of the bacteria in treated juices also showed that the combined treatment caused more sublethal injury, which increased further inactivation at a relatively mild pH of 4.2 during storage. The results indicated that the combined treatment of HHP with dissolved CO(2) may provide an effective method for the preservation of low- or medium-acid fruit and vegetable juices at relatively low pressures. HHP alone inactivated bacteria effectively in high-acid fruit juice.

Ionization of water clusters by fast Highly Charged Ions: Stability, fragmentation, energetics and charge mobility

International Nuclear Information System (INIS)

Legendre, S; Maisonny, R; Capron, M; Bernigaud, V; Cassimi, A; Gervais, B; Grandin, J-P; Huber, B A; Manil, B; Rousseau, P; Tarisien, M; Adoui, L; Lopez-Tarifa, P; AlcamI, M; MartIn, F; Politis, M-F; Penhoat, M A Herve du; Vuilleumier, R; Gaigeot, M-P; Tavernelli, I

2009-01-01

We study dissociative ionization of water clusters by impact of fast Ni ions. Cold Target Recoil Ion Momentum Spectroscopy (COLTRIMS) is used to obtain information about stability, energetics and charge mobility of the ionized clusters. An unusual stability of the (H 2 O) 4 H ''+ ion is observed, which could be the signature of the so called ''Eigen'' structure in gas phase water clusters. High charge mobility, responsible for the formation of protonated water clusters that dominate the mass spectrum, is evidenced. These results are supported by CPMD and TDDFT simulations, which also reveal the mechanisms of such mobility.

Fabrication of enhancement-mode AlGaN/GaN high electron mobility transistors using double plasma treatment

Energy Technology Data Exchange (ETDEWEB)

Lim, Jong-Won, E-mail: jwlim@etri.re.kr [Photonic/Wireless Convergence Components Dept., IT Materials and Components Lab., Electronics and Telecommunications Research Institute, Daejeon 305-700 (Korea, Republic of); Ahn, Ho-Kyun; Kim, Seong-il; Kang, Dong-Min; Lee, Jong-Min; Min, Byoung-Gue; Lee, Sang-Heung; Yoon, Hyung-Sup; Ju, Chull-Won; Kim, Haecheon; Mun, Jae-Kyoung; Nam, Eun-Soo [Photonic/Wireless Convergence Components Dept., IT Materials and Components Lab., Electronics and Telecommunications Research Institute, Daejeon 305-700 (Korea, Republic of); Park, Hyung-Moo [Photonic/Wireless Convergence Components Dept., IT Materials and Components Lab., Electronics and Telecommunications Research Institute, Daejeon 305-700 (Korea, Republic of); Division of Electronics and Electrical Engineering, Dongguk University, Seoul (Korea, Republic of)

2013-11-29

We report the fabrication and DC and microwave characteristics of 0.5 μm AlGaN/GaN high electron mobility transistors using double plasma treatment process. Silicon nitride layers 700 and 150 Å thick were deposited by plasma-enhanced chemical vapor deposition at 260 °C to protect the device and to define the gate footprint. The double plasma process was carried out by two different etching techniques to obtain enhancement-mode AlGaN/GaN high electron mobility transistors with 0.5 μm gate lengths. The enhancement-mode AlGaN/GaN high electron mobility transistor was prepared in parallel to the depletion-mode AlGaN/GaN high electron mobility transistor device on one wafer. Completed double plasma treated 0.5 μm AlGaN/GaN high electron mobility transistor devices fabricated by dry etching exhibited a peak transconductance, gm, of 330 mS/mm, a breakdown voltage of 115 V, a current-gain cutoff frequency (f{sub T}) of 18 GHz, and a maximum oscillation frequency (f{sub max}) of 66 GHz. - Highlights: • The double plasma process was carried out by two different etching techniques. • Double plasma treated device exhibited a transconductance of 330 mS/mm. • Completed 0.5 μm gate device exhibited a current-gain cutoff frequency of 18 GHz. • The off-state breakdown voltage of 115 V for 0.5 μm gate device was obtained. • Continuous-wave output power density of 4.3 W/mm was obtained at 2.4 GHz.

Fabrication of enhancement-mode AlGaN/GaN high electron mobility transistors using double plasma treatment

International Nuclear Information System (INIS)

Lim, Jong-Won; Ahn, Ho-Kyun; Kim, Seong-il; Kang, Dong-Min; Lee, Jong-Min; Min, Byoung-Gue; Lee, Sang-Heung; Yoon, Hyung-Sup; Ju, Chull-Won; Kim, Haecheon; Mun, Jae-Kyoung; Nam, Eun-Soo; Park, Hyung-Moo

2013-01-01

We report the fabrication and DC and microwave characteristics of 0.5 μm AlGaN/GaN high electron mobility transistors using double plasma treatment process. Silicon nitride layers 700 and 150 Å thick were deposited by plasma-enhanced chemical vapor deposition at 260 °C to protect the device and to define the gate footprint. The double plasma process was carried out by two different etching techniques to obtain enhancement-mode AlGaN/GaN high electron mobility transistors with 0.5 μm gate lengths. The enhancement-mode AlGaN/GaN high electron mobility transistor was prepared in parallel to the depletion-mode AlGaN/GaN high electron mobility transistor device on one wafer. Completed double plasma treated 0.5 μm AlGaN/GaN high electron mobility transistor devices fabricated by dry etching exhibited a peak transconductance, gm, of 330 mS/mm, a breakdown voltage of 115 V, a current-gain cutoff frequency (f T ) of 18 GHz, and a maximum oscillation frequency (f max ) of 66 GHz. - Highlights: • The double plasma process was carried out by two different etching techniques. • Double plasma treated device exhibited a transconductance of 330 mS/mm. • Completed 0.5 μm gate device exhibited a current-gain cutoff frequency of 18 GHz. • The off-state breakdown voltage of 115 V for 0.5 μm gate device was obtained. • Continuous-wave output power density of 4.3 W/mm was obtained at 2.4 GHz

Mobile Iodine Mineralization Based on Malachite Transformation

Energy Technology Data Exchange (ETDEWEB)

Lee, Seung Yeop; Baik, Min Hoon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

Our new method that is proposed here, however, offer drastic cost cutting by using copper. Moreover, the selectivity of iodine in anion-rich water is advantage to lower the disposal cost by reducing the radioactive waste volume. Iodide (I{sup -}) is soluble and mobile in water, so it is very difficult to capture and precipitate it with common adsorbents. Until now, various exchanger and getter materials have been developed to capture radioactive iodine in wastewater. The materials developed generally showed a good performance under acidic conditions. However, the adsorption amounts were not relatively large in neutral and high pH conditions. Furthermore, the capacity to capture iodine is limited by their properties, such as the specific surface area and adsorbing affinity. Recently, Ag-coated materials have attracted attention as adsorbents. They have shown higher uptake for I- compared to other substances, but they are costly. Our new method that is proposed here, however, offer drastic cost cutting by using copper. Moreover, the selectivity of iodine in anion-rich water is advantage to lower the disposal cost by reducing the radioactive waste volume. Radioactive iodine isotopes are characterized as volatile and mobile species that are difficult to capture by adsorbents. In our study, we developed a new way to uptake and crystallize the mobile iodide as cuprous iodide (CuI). This method will be a promising way to simply stabilize iodide in a solid form with compacted volume.

In vitro synthesis and purification of PhIP-deoxyguanosine and PhIP-DNA oligomer covalent complexes

Energy Technology Data Exchange (ETDEWEB)

Freeman, J.

1994-12-01

2-Amino-1-methyl-6-phenylimidazo[4,5-b]pyridine (PhIP) is a heterocyclic amine compound formed when meats are cooked at high temperatures. PhIP damages DNA by forming covalent complexes with DNA carcinogen. In an effort to understand how the binding of PhIP to DNA may cause cancer, it is important to characterize the structures of PhIP-damaged DNA molecules. Our HPLC data support fluorescence and {sup 32}P Post-labeling studies which indicate the formation of several species of 2{prime}deoxyguanosine-(dG) or oligodeoxynucleotide-PhIP adducts. The reaction of PhIP with dG resulted in a reddish precipitate that was likely the major adduct, N-(deoxyguanosin-8-yl)-PhIP (dG-C8-PhIP) adduct, with a more polar adduct fraction remaining in the supernatant. Reversed-phase HPLC analysis of the adducts in the supernatant revealed the existence of species of much shorter retention times than the dG-C8-PhIP adduct, confirming that these species are more polar than dG-C8-PhIP. At least four adducts were formed in the reaction of PhIP with DNA oligomer. HPLC analysis of the PhIP-DNA oligomer supernatant after butanol extractions revealed four unresolved peaks which spectra had maximum wavelengths between 340 and 360 nm. Though adduct peaks were not completely resolved, there was {approximately}3 minutes interval between the DNA oligomer peak and the adduct peaks. Furthermore, fluorescence emission data of the DNA oligomer-PhIP adduct solution show heterogeneous binding. The more polar PhIP adducts were fraction-collected and their structures will be solved by nuclear magnetic resonance or x-ray crystallography.

Mobility and Bioavailability of Radionuclides in Soils

International Nuclear Information System (INIS)

Iurian, A.; Olufemi Phaneuf, M.; Mabit, L.

2016-01-01

It is crucial to understand the behavior of radionuclides in the environment, their potential mobility and bioavailability related to long-term persistence, radiological hazards, and impact on human health. Such key information is used to develop strategies that support policy decisions. The environmental behavior of radionuclides depends on ecosystem characteristics. A given soil’s capacity to immobilize radionuclides has been proved to be the main factor responsible for their resulting activity concentrations in plants. The mobility and bioavailability of radionuclides in soils is complex, depending on clay-sized soil fraction, clay mineralogy, organic matter, cation exchange capacity, pH and quantities of competing cations. Moreover, plant species have different behaviors regarding radionuclide absorption depending on soil and plan characteristics

Open-gated pH sensor fabricated on an undoped-AlGaN/GaN HEMT structure.

Science.gov (United States)

Abidin, Mastura Shafinaz Zainal; Hashim, Abdul Manaf; Sharifabad, Maneea Eizadi; Rahman, Shaharin Fadzli Abd; Sadoh, Taizoh

2011-01-01

The sensing responses in aqueous solution of an open-gated pH sensor fabricated on an AlGaN/GaN high-electron-mobility-transistor (HEMT) structure are investigated. Under air-exposed ambient conditions, the open-gated undoped AlGaN/GaN HEMT only shows the presence of a linear current region. This seems to show that very low Fermi level pinning by surface states exists in the undoped AlGaN/GaN sample. In aqueous solution, typical current-voltage (I-V) characteristics with reasonably good gate controllability are observed, showing that the potential of the AlGaN surface at the open-gated area is effectively controlled via aqueous solution by the Ag/AgCl gate electrode. The open-gated undoped AlGaN/GaN HEMT structure is capable of distinguishing pH level in aqueous electrolytes and exhibits linear sensitivity, where high sensitivity of 1.9 mA/pH or 3.88 mA/mm/pH at drain-source voltage, V(DS) = 5 V is obtained. Due to the large leakage current where it increases with the negative gate voltage, Nernstian like sensitivity cannot be determined as commonly reported in the literature. This large leakage current may be caused by the technical factors rather than any characteristics of the devices. Surprisingly, although there are some imperfections in the device preparation and measurement, the fabricated devices work very well in distinguishing the pH levels. Suppression of current leakage by improving the device preparation is likely needed to improve the device performance. The fabricated device is expected to be suitable for pH sensing applications.

Open-Gated pH Sensor Fabricated on an Undoped-AlGaN/GaN HEMT Structure

Directory of Open Access Journals (Sweden)

Taizoh Sadoh

2011-03-01

Full Text Available The sensing responses in aqueous solution of an open-gated pH sensor fabricated on an AlGaN/GaN high-electron-mobility-transistor (HEMT structure are investigated. Under air-exposed ambient conditions, the open-gated undoped AlGaN/GaN HEMT only shows the presence of a linear current region. This seems to show that very low Fermi level pinning by surface states exists in the undoped AlGaN/GaN sample. In aqueous solution, typical current-voltage (I-V characteristics with reasonably good gate controllability are observed, showing that the potential of the AlGaN surface at the open-gated area is effectively controlled via aqueous solution by the Ag/AgCl gate electrode. The open-gated undoped AlGaN/GaN HEMT structure is capable of distinguishing pH level in aqueous electrolytes and exhibits linear sensitivity, where high sensitivity of 1.9 mA/pH or 3.88 mA/mm/pH at drain-source voltage, VDS = 5 V is obtained. Due to the large leakage current where it increases with the negative gate voltage, Nernstian like sensitivity cannot be determined as commonly reported in the literature. This large leakage current may be caused by the technical factors rather than any characteristics of the devices. Surprisingly, although there are some imperfections in the device preparation and measurement, the fabricated devices work very well in distinguishing the pH levels. Suppression of current leakage by improving the device preparation is likely needed to improve the device performance. The fabricated device is expected to be suitable for pH sensing applications.

Colloid mobilization and heavy metal transport in the sampling of soil solution from Duckum soil in South Korea.

Science.gov (United States)

Lee, Seyong; Ko, Il-Won; Yoon, In-Ho; Kim, Dong-Wook; Kim, Kyoung-Woong

2018-03-24

Colloid mobilization is a significant process governing colloid-associated transport of heavy metals in subsurface environments. It has been studied for the last three decades to understand this process. However, colloid mobilization and heavy metal transport in soil solutions have rarely been studied using soils in South Korea. We investigated the colloid mobilization in a variety of flow rates during sampling soil solutions in sand columns. The colloid concentrations were increased at low flow rates and in saturated regimes. Colloid concentrations increased 1000-fold higher at pH 9.2 than at pH 7.3 in the absence of 10 mM NaCl solution. In addition, those were fourfold higher in the absence than in the presence of the NaCl solution at pH 9.2. It was suggested that the mobility of colloids should be enhanced in porous media under the basic conditions and the low ionic strength. In real field soils, the concentrations of As, Cr, and Pb in soil solutions increased with the increase in colloid concentrations at initial momentarily changed soil water pressure, whereas the concentrations of Cd, Cu, Fe, Ni, Al, and Co lagged behind the colloid release. Therefore, physicochemical changes and heavy metal characteristics have important implications for colloid-facilitated transport during sampling soil solutions.

C-reactive protein and high mobility group box 1 in dogs with gastric dilatation and volvulus.

Science.gov (United States)

Uhrikova, Ivana; Rauserova-Lexmaulova, Leona; Rehakova, Kristina; Scheer, Peter; Doubek, Jaroslav

2015-01-01

To (1) measure C-reactive protein (CRP) and high mobility group box 1 (HMGB1) and (2) evaluate their prognostic value and relationship to severity of systemic inflammatory response syndrome, routine hematological and acid-base parameters in dogs with gastric dilatation volvulus (GDV). Prospective observational study from September 2010 to June 2012. Veterinary teaching hospital. Forty-one client-owned dogs with GDV. None. Blood was collected before surgery (baseline), postsurgery, 6-10 hours postsurgery, and 18-22 hours postsurgery. CRP and HMGB1 were measured in all samples, and routine hematological, biochemical, and acid-base analyses were performed. Only baseline and postsurgery samples were used from nonsurvivors (n = 10). CRP increased significantly from postsurgery sampling to 18-22 hours postsurgery, while HMGB1 did not change over time. There was a significant difference in HMGB1 between survivors and nonsurvivors over time. Both proteins correlated with systemic inflammatory response syndrome severity, total leukocyte, segmented neutrophils, and band counts. HMGB1 correlated also with acid-base parameters (pH, bicarbonate, base excess). HMGB1 and CRP behaved differently in regards to their kinetic patterns, with HMGB1 appearing to better reflect the severity of tissue injury in dogs with GDV than CRP. © Veterinary Emergency and Critical Care Society 2015.

Ultra-bright red-emitting photostable perylene bisimide dyes: new indicators for ratiometric sensing of high pH or carbon dioxide.

Science.gov (United States)

Pfeifer, David; Klimant, Ingo; Borisov, Sergey M

2018-05-08

New pH sensitive perylene bisimide indicator dyes were synthesised and used for fabrication of optical sensors. The highly photostable dyes show absorption/emission bands in the red/near-infrared (NIR) region of the electromagnetic spectrum, high molar absorption coefficients (up to 100 000 M-1 cm-1) and fluorescence quantum yields close to unity. The absorption and emission spectra show strong bathochromic shift upon deprotonation of imidazole nitrogen which makes the dyes promising as ratiometric fluorescent indicators. Physical entrapment of the indicators into polyurethane hydrogel enables pH determination in alkaline pH. It is also shown that plastic carbon dioxide solid state sensor can be manufactured via immobilization of the pH indicator in a hydrophilic polymer, along with a quaternary ammonium base. The influence of plasticizer, different lipophilic bases and humidity on the sensitivity of the sensor material were systematically investigated. The disubstituted perylene, particularly, features two deprotonation equilibria enabling sensing over a very broad range from 0.5 to 1000 hPa pCO2. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effects of incubation on solubility and mobility of trace metals in two contaminated soils

International Nuclear Information System (INIS)

Ma, Lena Q.; Dong Yan

2004-01-01

Much research has focused on changes in solubility and mobility of trace metals in soils under incubation. In this experiment, changes in solubility and mobility of trace metals (Pb, Cu and As) and Fe in two contaminated soils from Tampa, Florida and Montreal, Canada were examined. Soils of 30 g were packed in columns and were incubated for 3-80 days under water-flooding incubation. Following incubation, metal concentrations in pore water (water soluble) and in 0.01 M CaCl 2 leachates (exchangeable+water soluble) were determined. While both soils were contaminated with Pb (1600-2500 mg kg -1 ), Tampa soil was also contaminated with As (230 mg kg -1 ). Contrast to the low pH (3.8) of Tampa soil, Montreal soil had an alkaline pH of 7.7 and high Ca of 1.6%. Concentrations of Fe(II) increased with incubation time in the Tampa soil mainly due to reductive Fe dissolution, but decreased in the Montreal soil possibly due to formation of FeCO 3 . The inverse relationship between concentrations of Pb and Fe(II) in pore water coupled with the fact that Fe(II) concentrations were much greater than those of Pb in pore water may suggest the importance of Fe(II) in controlling Pb solubility in soils. However, changes in concentrations of Fe(II), Pb, Cu and As in pore water with incubation time were similar to those in leachate, i.e. water soluble metals were positively related to exchangeable metals in the two contaminated soils. This research suggests the importance of Fe in controlling metal solubility and mobility in soils under water-flooded incubation. - Iron is important in controlling metal solubility and mobility in flooded soils

Uranium fate in wetland mesocosms: Effects of plants at two iron loadings with different pH values

Science.gov (United States)

Small-scale continuous flow wetland mesocosms (~0.8 L) were used to evaluate how plant roots under different iron loadings affect uranium (U) mobility. When significant concentrations of ferrous iron (Fe) were present at circumneutral pH values, U concentrations in root exposed ...

Cassette pontoon bridge of high mobility

Directory of Open Access Journals (Sweden)

Krzysztof KOSIUCZENKO

2011-01-01

Full Text Available Looking through the known and used buoyant systems, it can be remarked that the single buoyant segments are the stiff objects made of steel or plastic with variable dimensions and a complex construction. The ready to use buoyant segments, that assure the proper displacement, must have the factory leak-tightness. They take up a big transportation volume and need the assurance of the suitably abundant means of transport. Usually the heavy wheeled vehicles are needed because of high own mass of buoyant segment and large gauges. The exploitation of such constructions is very expensive. A cassette pontoon bridge, presented in this paper, is the proposition of the increase of the mobility of construction. The decrease of the single buoyant segment dimensions with the assurance of the capacity leads that more segments fit into in the same dimensions of the loading compartment of the vehicle and storage accommodation. The application of standardized joints assures the assembly efficiency with not numerous crew.

Gender inequalities in transnational academic mobility and the ideal type of academic entrepreneur

OpenAIRE

Leemann, Regula Julia

2010-01-01

Based on a study on academic career paths of PhD graduates in Switzerland, this paper is concerned with the individual and institutional factors that affect transnational academic mobility in the postdoctoral period. It will be argued that the institutionalisation of geographic mobility in academic career paths through research funding institutions and universities have gendering and stratifying effects. Complex formations related to gender, partnership, children, and dual-career constellatio...

Development of an accurate pH measurement methodology for the pore fluids of low pH cementitious materials

International Nuclear Information System (INIS)

Alonso, M. C.; Garcia Calvo, J. L.; Walker, C.

2012-08-01

The main objective of this project has been the development of an agreed set of protocols for the pH measurement of the pore fluid of a low pH cementitious material. Three protocols have been developed (Chapter 2), a reference method, based on pore fluid expression (PFE), and two routine methods with and without filtering, based on Ex Situ Leaching (ESL) procedures. Templates have been designed on which to record details of the pH measurement for the reference (PFE) method (Appendix C) and the routine (ESL) methods without and with filtering (Appendix D). Preliminary protocols were based on a broad review of the literature (Appendix A) and refined through a series of test experiments of the more critical parameters (Appendix B). After definition of the preliminary protocols, two phases of interlaboratory tests were performed. The first phase (Chapter 3) used the same low pH cement paste and enabled the nine participating laboratories to use, become familiar with and to identify any problems/uncertainties in the preliminary protocols. The reported pH values were subjected to a statistical analysis of the (within laboratory) repeatability and (between-laboratory) reproducibility and so provided a reliability test of the preliminary protocols. The second phase (Chapter 4) of interlaboratory tests used four different candidate low pH cementitious materials in the same nine laboratories, which allowed testing, validation and comparison of the reported pH values, which were obtained using the final protocols for the reference (PFE) and routine (ESL) methods by statistical analysis. The proposed final protocols (Chapter 2) have resulted in the reported pH values having low deviation and high reproducibility and repeatability. This will allow confidence in the pH value when selecting a candidate low pH cementitious material to be used in the engineered component of a high-level nuclear waste repository

Development of an accurate pH measurement methodology for the pore fluids of low pH cementitious materials

Energy Technology Data Exchange (ETDEWEB)

Alonso, M. C.; Garcia Calvo, J. L. [The Spanish National Research Council (CSIC), Madrid (Spain); Walker, C. [Japan Atomic Energy Agency (JAEA), Ibaraki (Japan)] [and others

2012-08-15

The main objective of this project has been the development of an agreed set of protocols for the pH measurement of the pore fluid of a low pH cementitious material. Three protocols have been developed (Chapter 2), a reference method, based on pore fluid expression (PFE), and two routine methods with and without filtering, based on Ex Situ Leaching (ESL) procedures. Templates have been designed on which to record details of the pH measurement for the reference (PFE) method (Appendix C) and the routine (ESL) methods without and with filtering (Appendix D). Preliminary protocols were based on a broad review of the literature (Appendix A) and refined through a series of test experiments of the more critical parameters (Appendix B). After definition of the preliminary protocols, two phases of interlaboratory tests were performed. The first phase (Chapter 3) used the same low pH cement paste and enabled the nine participating laboratories to use, become familiar with and to identify any problems/uncertainties in the preliminary protocols. The reported pH values were subjected to a statistical analysis of the (within laboratory) repeatability and (between-laboratory) reproducibility and so provided a reliability test of the preliminary protocols. The second phase (Chapter 4) of interlaboratory tests used four different candidate low pH cementitious materials in the same nine laboratories, which allowed testing, validation and comparison of the reported pH values, which were obtained using the final protocols for the reference (PFE) and routine (ESL) methods by statistical analysis. The proposed final protocols (Chapter 2) have resulted in the reported pH values having low deviation and high reproducibility and repeatability. This will allow confidence in the pH value when selecting a candidate low pH cementitious material to be used in the engineered component of a high-level nuclear waste repository.

BSA-coated nanoparticles for improved SERS-based intracellular pH sensing.

Science.gov (United States)

Zheng, Xiao-Shan; Hu, Pei; Cui, Yan; Zong, Cheng; Feng, Jia-Min; Wang, Xin; Ren, Bin

2014-12-16

Local microenvironment pH sensing is one of the key parameters for the understanding of many biological processes. As a noninvasive and high sensitive technique, surface-enhanced Raman spectroscopy (SERS) has attracted considerable interest in the detection of the local pH of live cells. We herein develop a facile way to prepare Au-(4-MPy)-BSA (AMB) pH nanosensor. The 4-MPy (4-mercaptopyridine) was used as the pH sensing molecule. The modification of the nanoparticles with BSA not only provides a high sensitive response to pH changes ranging from pH 4.0 to 9.0 but also exhibits a high sensitivity and good biocompatibility, stability, and reliability in various solutions (including the solutions of high ionic strength or with complex composition such as the cell culture medium), both in the aggregation state or after long-term storage. The AMB pH nanosensor shows great advantages for reliable intracellular pH analysis and has been successfully used to monitor the pH distribution of live cells and can address the grand challenges in SERS-based pH sensing for practical biological applications.

A validated stability-indicating high performance liquid chromatographic method for moxifloxacin hydrochloride and ketorolac tromethamine eye drops and its application in pH dependent degradation kinetics

Directory of Open Access Journals (Sweden)

Jayant B Dave

2013-01-01

Full Text Available Background and Aim: A fixed dose combination of moxifloxacin hydrochloride and ketorolac tromethamine is used in ratio of 1:1 as eye drops for the treatment of the reduction of post operative inflammatory conditions of the eye. A simple, precise, and accurate High Performance Liquid Chromatographic (HPLC method was developed and validated for determination of moxifloxacin hydrochloride and ketorolac tromethamine in eye drops. Materials and Methods: Isocratic HPLC separation was achieved on a ACE C 18 column (C 18 (5 μm, 150 mm×4.6 mm, i.d. using the mobile phase 10 mM potassium di-hydrogen phosphate buffer pH 4.6-Acetonitrile (75:25 v/v at a flow rate of 1.0 mL/min. The detection was performed at 307 nm. Drugs were subjected to acid, alkali and neutral hydrolysis, oxidation and photo degradation. Moreover, the proposed HPLC method was utilized to investigate the pH dependent degradation kinetics of moxifloxacin hydrochloride and ketorolac tromethamine in buffer solutions at different pH values like 2.0, 6.8 and 9.0. Results and Conclusion: The retention time (t R of moxifloxacin hydrochloride and ketorolac tromethamine were 3.81±0.01 and 8.82±0.02 min, respectively. The method was linear in the concentration range of 2-20 μ/mL each for moxifloxacin hydrochloride and ketorolac tromethamine with a correlation coefficient of 0.9996 and 0.9999, respectively. The method was validated for linearity, precision, accuracy, robustness, specificity, limit of detection and limit of quantitation. The drugs could be effectively separated from different degradation products and hence the method can be used for stability analysis. Different kinetics parameters like apparent first-order rate constant, half-life and t 90 (time for 90% potency left were calculated.

Unveiling the Structural Origin of the High Carrier Mobility of a Molecular Monolayer on Boron Nitride

OpenAIRE

Xu, Rui; He, Daowei; Zhang, Yuhan; Wu, Bing; Liu, Fengyuan; Meng, Lan; Liu, Jun-Fang; Wu, Qisheng; Shi, Yi; Wang, Jinlan; Nie, Jia-Cai; Wang, Xinran; He, Lin

2014-01-01

Very recently, it was demonstrated that the carrier mobility of a molecular monolayer dioctylbenzothienobenzothiophene (C8-BTBT) on boron nitride can reach 10 cm2/Vs, the highest among the previously reported monolayer molecular field-effect transistors. Here we show that the high-quality single crystal of the C8-BTBT monolayer may be the key origin of the record-high carrier mobility. We discover that the C8-BTBT molecules prefer layer-by-layer growth on both hexagonal boron nitride and grap...

Plant Habitat (PH)

Science.gov (United States)

Onate, Bryan

2016-01-01

The International Space Station (ISS) will soon have a platform for conducting fundamental research of Large Plants. Plant Habitat (PH) is designed to be a fully controllable environment for high-quality plant physiological research. PH will control light quality, level, and timing, temperature, CO2, relative humidity, and irrigation, while scrubbing ethylene. Additional capabilities include leaf temperature and root zone moisture and oxygen sensing. The light cap will have red (630 nm), blue (450 nm), green (525 nm), far red (730 nm) and broad spectrum white LEDs. There will be several internal cameras (visible and IR) to monitor and record plant growth and operations.

Computer simulation of immobilized pH gradients at acidic and alkaline extremes - A quest for extended pH intervals

Science.gov (United States)

Mosher, Richard A.; Bier, Milan; Righetti, Pier Giorgio

1986-01-01

Computer simulations of the concentration profiles of simple biprotic ampholytes with Delta pKs 1, 2, and 3, on immobilized pH gradients (IPG) at extreme pH values (pH 3-4 and pH 10-11) show markedly skewed steady-state profiles with increasing kurtosis at higher Delta pK values. Across neutrality, all the peaks are symmetric irrespective of their Delta pK values, but they show very high contribution to the conductivity of the background gel and significant alteration of the local buffering capacity. The problems of skewness, due to the exponential conductivity profiles at low and high pHs, and of gel burning due to a strong electroosmotic flow generated by the net charges in the gel matrix, also at low and high pHs, are solved by incorporating in the IPG gel a strong viscosity gradient. This is generated by a gradient of linear polyacrylamide which is trapped in the gel by the polymerization process.

Ion-pair high performance liquid chromatographic retention behavior of salicylic acid and its derivatives

Energy Technology Data Exchange (ETDEWEB)

Lee, K.W.; Chung, Y.S. [Chungbuk National University, Cheongju (Korea); Oh, S.K. [Handok Pharmaceuticals Co. Ltd., Chungbuk (Korea)

1999-06-01

The ion-pair high performance liquid chromatographic elution behavior of salicylic acid and its derivatives was studied with measuring capacity factor, k', changing the concentration of ion-pairing reagent (tetrabutylammonium chloride, TBACl) in mobile phase. As a result, it was found that k' of the samples increase at pH 7.2 as the TBACl concentration increase. The derivatives of salicylic acid were separated each other at an optimum mobile phase condition which was found from the observation of the retention behavior. The optimum mobile phase condition was methanol solution(MeOH:H{sub 2}O 30:70) containing 20 mM TBACl for the determination of salicylic acid and methanol solution (MeOH:H{sub 2}O 20:80) containing 40 mM TBACl for p-aminosalicylic acid at pH 7.2. The method has been applied for the analysis of the contents of salicylic acid derivatives in an aspirin tablet and a tuberculosis curing agent. 8 refs., 4 figs., 2 tabs.

Ultra-high mobility transparent organic thin film transistors grown by an off-centre spin-coating method.

Science.gov (United States)

Yuan, Yongbo; Giri, Gaurav; Ayzner, Alexander L; Zoombelt, Arjan P; Mannsfeld, Stefan C B; Chen, Jihua; Nordlund, Dennis; Toney, Michael F; Huang, Jinsong; Bao, Zhenan

2014-01-01

Organic semiconductors with higher carrier mobility and better transparency have been actively pursued for numerous applications, such as flat-panel display backplane and sensor arrays. The carrier mobility is an important figure of merit and is sensitively influenced by the crystallinity and the molecular arrangement in a crystal lattice. Here we describe the growth of a highly aligned meta-stable structure of 2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene (C8-BTBT) from a blended solution of C8-BTBT and polystyrene by using a novel off-centre spin-coating method. Combined with a vertical phase separation of the blend, the highly aligned, meta-stable C8-BTBT films provide a significantly increased thin film transistor hole mobility up to 43 cm(2) Vs(-1) (25 cm(2) Vs(-1) on average), which is the highest value reported to date for all organic molecules. The resulting transistors show high transparency of >90% over the visible spectrum, indicating their potential for transparent, high-performance organic electronics.

A model to explain high values of pH in an alkali sodic soil Modelo para explicar valores elevados de pH em um solo sódico alcalino

Directory of Open Access Journals (Sweden)

José Guerrero-Alves

2002-12-01

Full Text Available For alkali sodic soils (pH>8.5, the "hydrolysis of exchangeable sodium" has been used as a possible explanation for the alkalinity production and rise in pH of these soils. As an alternative to this hypothesis, a model was developed to simulate and to explain that the alkalinity production and rise in pH is possible in a soil that accumulates alkaline sodium salts and CaCO3. Several simulations were performed by using different combinations of CO2 partial pressures (P, presence or absence of MgCO3, along with experimental values of exchangeable sodium percentage (ESP and ion concentrations in saturation extracts from an alkali sodic soil (named Pantanal. A hypothetical system with similar conditions to the Pantanal soil but with a Gapon selectivity coefficient (KG of 0.01475 (mmol L-1-1/2 was also considered. Good agreement was obtained between experimental and predicted values for pH and ion concentrations in the soil solution when the model (without MgCO3 was applied to the Pantanal soil. However, KG values calculated for the Pantanal soil were generally higher than 0.01475 (mmol L-1-1/2. Moreover, high pH values and elevated ionic strength were obtained when a KG of 0.01475 (mmol L-1-1/2 was used at high ESP (similar to those found in the Pantanal soil. KG values obtained for the Pantanal soil and the results obtained in the simulation of the hypothetical system are suggesting that a value higher than 0.01475 (mmol L-1-1/2 should be used to adequately simulate the behavior of the Pantanal soil at low ionic strength and high ESP values.Em solos alcalino sódicos (pH>8,5, a "hidrólise de sódio trocável" tem sido usada como uma possível explicação para a produção de álcali e elevação do pH nestes solos. Como uma alternativa a essa hipótese, um modelo foi desenvolvido para simular e explicar que a produção de álcali e elevação do pH é possível num solo que acumula sais alcalinos de sódio e CaCO3. Várias simulações foram

Patterning of high mobility electron gases at complex oxide interfaces

DEFF Research Database (Denmark)

Trier, Felix; Prawiroatmodjo, G. E. D. K.; von Soosten, Merlin

2015-01-01

Oxide interfaces provide an opportunity for electronics. However, patterning of electron gases at complex oxide interfaces is challenging. In particular, patterning of complex oxides while preserving a high electron mobility remains underexplored and inhibits the study of quantum mechanical effects...... of amorphous-LSM (a-LSM) thin films, which acts as a hard mask during subsequent depositions. Strikingly, the patterned modulation-doped interface shows electron mobilities up to ∼8 700 cm2/V s at 2 K, which is among the highest reported values for patterned conducting complex oxide interfaces that usually...... where extended electron mean free paths are paramount. This letter presents an effective patterning strategy of both the amorphous-LaAlO3/SrTiO3 (a-LAO/STO) and modulation-doped amorphous-LaAlO3/La7/8Sr1/8MnO3/SrTiO3 (a-LAO/LSM/STO) oxide interfaces. Our patterning is based on selective wet etching...

High-precision high-sensitivity clock recovery circuit for a mobile payment application

International Nuclear Information System (INIS)

Sun Lichong; Yan Na; Min Hao; Ren Wenliang

2011-01-01

This paper presents a fully integrated carrier clock recovery circuit for a mobile payment application. The architecture is based on a sampling-detection module and a charge pump phase locked loop. Compared with clock recovery in conventional 13.56 MHz transponders, this circuit can recover a high-precision consecutive carrier clock from the on/off keying (OOK) signal sent by interrogators. Fabricated by a SMIC 0.18-μm EEPROM CMOS process, this chip works from a single power supply as low as 1.5 V Measurement results show that this circuit provides 0.34% frequency deviation and 8 mV sensitivity. (semiconductor integrated circuits)

Transport phenomena in high Tc superconductors. Resume of Ph.D thesis

International Nuclear Information System (INIS)

Crisan, I.A.

1994-01-01

This is an extended abstract of the Ph. D. thesis devoted to the transport phenomena in high-Tc superconductors. There are three chapters. The first chapter presents an overview of the essential theoretical aspects concerning the vortex dynamics particularly in ceramic superconductors. The chapter two gives a description of the preparation methods of superconductor samples used by the author as well as the measurement devices for volt-ampere characteristics and the associated electronic circuitry. In the third chapter there are presented the experimental data obtained from different samples prepared in different temperature and magnetic field conditions. The obtained results are finally interpreted in the frame of existent or original models. (M.I.C.). 31 Refs

Novel chelating agents for iron, manganese, zinc, and copper mixed fertilisation in high pH soil-less cultures.

Science.gov (United States)

López-Rayo, Sandra; Nadal, Paloma; Lucena, Juan J

2016-03-15

Studies about simultaneous fertilisation with several micronutrients have increased in recent years, as Fe, Mn and Zn deficiencies may appear in the same culture conditions. In fertigation, the replacement of sulfates by synthetic chelates is essential in areas with high pH irrigation water and substrates. Ethylenediamine-N-(2-hydroxyphenylacetic acid)-N'-(4-hydroxyphenylacetic acid) (o,p-EDDHA) and ethylenediamine disuccinic acid (EDDS) are novel chelating agents whose efficacy in simultaneous fertilisation of Zn, Mn and Cu is unknown. This work evaluates the effectiveness of both ligands compared to traditional ligands (EDTA, HEEDTA and DTPA) applied as micronutrient chelate mixtures to soybean and navy bean plants grown in soil-less cultures at high pH by analysing the SPAD and micronutrient nutritional status, including the Composition Nutritional Diagnosis (CND) analysis tool. The application of micronutrients using o,p-EDDHA was more effective in providing Mn and Zn than traditional ligands or sulfates. The application using EDDS increased the Zn nutrition. The results are well correlated with the chemical stability of the formulations. The combined application of Mn and Zn as o,p-EDDHA chelates can represent a more effective source than traditional chelates in micronutrient fertiliser mixtures in soil-less cultures at a high pH. © 2015 Society of Chemical Industry.

Hydrothermal mobilization of pegmatite-hosted REE and Zr at Strange Lake, Canada: A reaction path model

Science.gov (United States)

Gysi, Alexander P.; Williams-Jones, Anthony E.

2013-12-01

, particularly at high temperature (400 °C). The LREE are more mobile than the HREE in saline HCl-bearing fluids due to the greater stability of LREE-chloride complexes. The simulated mineralogy is consistent with the zonation observed in the pegmatites and with fluid-rock interaction at conditions that were rock-buffered in the pegmatite borders (low fluid/rock ratio; and pH > 4) and fluid-buffered in the cores (high fluid/rock ratio; pH ⩽ 2). We propose a model in which saline HCl-HF-bearing fluids created pathways during acidic alteration from the pegmatite cores outward. This led to the mobilization of REE and Zr due to progressive alteration of primary silicate minerals and increased acidity upon cooling. The key requirement for REE and Zr mobilization in peralkaline igneous intrusions is the formation of an acidic subsystem with high fluid/rock ratios that increases the overall permeability of the rocks. In these zones, the extent of late stage hydrothermal redistribution and concentration of REE and Zr depends on the buffering capacity of the rocks and the availability of fluids that may produce autometasomatic rock alteration, interact with external rock units and/or mix with fluids from other sources. b The detection limits of Yb were 1043 ppm for zircon, 380 ppm for gadolinite-group minerals and 380 ppm for REE-F-(CO2)-minerals. bAja et al. (1995). cMigdisov et al. (2011). dTagirov et al. (1997). eTagirov and Schott (2001). fMigdisov et al. (2009) with REE (La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu). b Calculated using the methods of the Chermak and Rimstidt (1989), Berman and Brown (1985) and Holland (1989) with molar volume of arfvedsonite from Hawthorne (1976). cZotov et al. (1998). d GEM-Selektor v.3 database (http://gems.web.psi.ch). eMigdisov et al. (2009).

Mobilidade do ametryn em latossolos brasileiros Mobility of ametryn in Brazilian latosols

Directory of Open Access Journals (Sweden)

L.O.C. Silva

2012-12-01

's mobility. The substrates used were: Red-Yellow Latosol (LVA pH 5.40 and pH 6.11, Red-Yellow humic Latosol (LVAh pH 4.8 and pH 6.24, Red Latosol (LV and pH 5.00 pH 6.06 and Yellow Latosol (LA pH 6.30 and 10 depths in the column (0-5, 5-10, 10-15, 15-20, 20-25, 25-30, 30-35, 35 - 40, 40-45 and 45-50cm and a control without herbicide application on each substrate, with four replications. The substrates were placed in columns properly prepared for mobility studies. The species Cucumis sativus was used as a bio-indicator of the presence of ametryn. It was concluded that the organic matter levels and soil pH evaluated were the characteristics that most interfered with ametryn's mobility and that the biological assay proved to be effective as an indicator of this herbicide's leaching in the columns. Therefore, the method for biological assays can be used as a preliminary method or as a complement to the instrumental method to confirm results and/or the reduction of costs and analysis time.

Novel Technique to improve the pH of Acidic Barren Soil using Electrokinetic-bioremediation with the application of Vetiver Grass

Science.gov (United States)

Azhar, A. T. S.; Nabila, A. T. A.; Nurshuhaila, M. S.; Zaidi, E.; Azim, M. A. M.; Zahin, A. M. F.

2016-11-01

Residual acidic slopes which are not covered by vegetation greatly increases the risk of soil erosion. In addition, low soil pH can bring numerous problems such as Al and Fe toxicity, land degradation issues and some problems related to vegetation. In this research, a series of electrokinetic bioremediation (EK-Bio) treatments using Bacillus sphaericus, Bacillus subtilis and Pseudomonas putida with a combination of Vetiver grass were performed in the laboratory. Investigations were conducted for 14 days and included the observation of changes in the soil pH and the mobilization of microorganism cells through an electrical gradient of 50 V/m under low pH. Based on the results obtained, this study has successfully proven that the pH of soil increases after going through electrokinetic bioremediation (EK-Bio). The treatment using Bacillus sphaericus increases the pH from 2.95 up to 4.80, followed by Bacillus subtilis with a value of 4.66. Based on the overall performance, Bacillus sphaericus show the highest number of bacterial cells in acidic soil with a value of 6.6 × 102 cfu/g, followed by Bacillus subtilis with a value of 5.7 × 102 cfu/g. In conclusion, Bacillus sphaericus and Bacillus subtilis show high survivability and is suitable to be used in the remediation of acidic soil.

The effect of pH and ionic strength on proton adsorption by the thermophilic bacterium Anoxybacillus flavithermus

Science.gov (United States)

Burnett, Peta-Gaye; Heinrich, Hannah; Peak, Derek; Bremer, Phil J.; McQuillan, A. James; Daughney, Christopher J.

2006-04-01

Numerous studies have utilized surface complexation theory to model proton adsorption behaviour onto mesophilic bacteria. However, few experiments, to date, have investigated the effects of pH and ionic strength on proton interactions with thermophilic bacteria. In this study, we characterize proton adsorption by the thermophile Anoxybacillus flavithermus by performing acid-base titrations and electrophoretic mobility measurements in NaNO 3 (0.001-0.1 M). Equilibrium thermodynamics (Donnan model) were applied to describe the specific chemical reactions that occur at the water-bacteria interface. Acid-base titrations were used to determine deprotonation constants and site concentrations for the important cell wall functional groups, while electrophoretic mobility data were used to further constrain the model. We observe that with increasing pH and ionic strength, the buffering capacity increases and the electrophoretic mobility decreases. We develop a single surface complexation model to describe proton interactions with the cells, both as a function of pH and ionic strength. Based on the model, the acid-base properties of the cell wall of A. flavithermus can best be characterized by invoking three distinct types of cell wall functional groups, with p Ka values of 4.94, 6.85, and 7.85, and site concentrations of 5.33, 1.79, and 1.42 × 10 -4 moles per gram of dry bacteria, respectively. A. flavithermus imparts less buffering capacity than pure mesophilic bacteria studied to date because the thermophile possesses a lower total site density (8.54 × 10 -4 moles per dry gram bacteria).

Drift mobility of thermalized and highly energetic holes in thin layers of amorphous dielectric SiC

International Nuclear Information System (INIS)

Sielski, Jan; Jeszka, Jeremiasz K.

2012-01-01

The development of new technology in the electronics industry requires new dielectric materials. It is also important to understand the charge-carrier transport mechanism in these materials. We examined the hole drift mobility in amorphous SiC dielectric thin films using the time-of-flight (TOF) method. Charge carriers were generated using an electron gun. The generated holes gave a dispersive TOF signal and the mobility was low. For electric field strengths above 4 x 10 5 V cm -1 the drift mobility shows a very strong dependence on the electric field and a weak temperature dependence (transport of ''high-energy'' charge carriers). At lower electric fields and for thermalized charge carriers the mobility is practically field independent and thermally activated. The observed phenomenon was attributed to the changes in the effective energy of the generated carriers moving in the high electric fields and consequently in the density of localized states taking part in the transport. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

High mobility AlGaN/GaN devices for β{sup −}-dosimetry

Energy Technology Data Exchange (ETDEWEB)

Schmid, Martin; Howgate, John; Ruehm, Werner [Helmholtz Zentrum München, Ingolstädter Landstraße 1, 85764 Neuherberg (Germany); Thalhammer, Stefan, E-mail: stefan.thalhammer@physik.uni-augsburg.de [Universität Augsburg, Universitätsstraße 1, 86159 Augsburg (Germany)

2016-05-21

There is a high demand in modern medical applications for dosimetry sensors with a small footprint allowing for unobtrusive or high spatial resolution detectors. To this end we characterize the sensoric response of radiation resistant high mobility AlGaN/GaN semiconductor devices when exposed to β{sup −}-emitters. The samples were operated as a floating gate transistor, without a field effect gate electrode, thus excluding any spurious effects from β{sup −}-particle interactions with a metallic surface covering. We demonstrate that the source–drain current is modulated in dependence on the kinetic energy of the incident β{sup −}-particles. Here, the signal is shown to have a linear dependence on the absorbed energy calculated from Monte Carlo simulations. Additionally, a stable and reproducible sensor performance as a β{sup −}-dose monitor is shown for individual radioisotopes. Our experimental findings and the characteristics of the AlGaN/GaN high mobility layered devices indicate their potential for future applications where small sensor size is necessary, like for instance brachytherapy.

The 2007 click it or ticket high-visibility seat belt mobilization : traffic tech.

Science.gov (United States)

2010-09-01

In May 2007 the National Highway Traffic Safety Administration : sponsored the fifth national Click It or Ticket (CIOT) : high-visibility seat belt enforcement mobilization, which followed : the CIOT program model of earned and paid media : publicizi...

Arsenic mobilization in a freshening groundwater system formed within glaciomarine deposits

International Nuclear Information System (INIS)

Cavalcanti de Albuquerque, R.; Kirste, D.

2012-01-01

Arsenic release to groundwater and conditions favoring As mobility are investigated in a system of aquifers formed within unconsolidated Quaternary sediments. The studied groundwater system is comprised of unconfined aquifers formed in glaciofluvial sediments with Ca–Mg–HCO 3 groundwater, and confined aquifers formed within glaciomarine sediments with high As (above 10 μg/L) Na–HCO 3 or Na–Cl groundwater. A positive relationship of As concentrations with the Na/(Ca + Mg) ratio of groundwater indicates that As release occurs in glaciomarine sediments concurrent to cation exchange reactions related to groundwater freshening. Arsenic is mobile in confined aquifers as a result of groundwater basic pH which prevents arsenate from adsorbing to mineral surfaces, and reducing conditions that favor speciation to arsenite. Selected extractions applied to sediment core samples indicate that As occurs in sediments predominantly in sulfide minerals and in Mn oxides and/or Fe oxyhydroxides. General positive relationships between As and the reduced species Fe 2+ , NH 3 and dissolved S 2− suggest that As release occurs at increasingly reducing conditions. Despite likely As release via Fe oxyhydroxide reductive dissolution, Fe remains at relatively low concentrations in groundwater (up to 0.37 mg/L) as a result of possible Fe adsorption and Fe reprecipitation as carbonate minerals favored by basic pH and high alkalinity. The presence of S 2− in some samples, a negative relationship between δ 34 S of SO 4 and SO 4 2- concentrations, and a positive relationship between δ 34 S and δ 18 O of SO 4 indicate that groundwater in confined aquifers is undergoing bacterial SO 4 reduction.

On the pH and Osmotic Stress Tolerance of High Ethanol Tolerant ...

African Journals Online (AJOL)

Saccharomyces yeast strains Y13, Y522 and Y1189 isolated from fermenting palm wine juice showed marked differences in their optimum growth pH and possessed osmotolerance comparable to established industrial yeast strains. Shifts in medium pH beyond the growth optimum elicited obvious reductions in growth rate ...

Kinase detection with gallium nitride based high electron mobility transistors.

Science.gov (United States)

Makowski, Matthew S; Bryan, Isaac; Sitar, Zlatko; Arellano, Consuelo; Xie, Jinqiao; Collazo, Ramon; Ivanisevic, Albena

2013-07-01

A label-free kinase detection system was fabricated by the adsorption of gold nanoparticles functionalized with kinase inhibitor onto AlGaN/GaN high electron mobility transistors (HEMTs). The HEMTs were operated near threshold voltage due to the greatest sensitivity in this operational region. The Au NP/HEMT biosensor system electrically detected 1 pM SRC kinase in ionic solutions. These results are pertinent to drug development applications associated with kinase sensing.

The measurement of the chemically mobile fraction of lead in soil using isotopic dilution analysis

International Nuclear Information System (INIS)

Kirchhoff, J.; Brand, J.; Schuettelkopf, H.

1992-12-01

The chemically available fraction of lead in eight soils measured by isotopic dilution analysis using 212 Pb ranged from 7 to 16% of the total content of lead in soil. The soluble fractions achieved values up to 63% of the total content in 1 M NH 4 NO 3 , 1 M MgCl 2 and 0.05 M DTPA solutions. Increasing the contact time between water and soil, the water-soil ratio from 1:1 to 5:1 and increasing the temperature of the soil-water suspension raised the chemically available fraction in soil. Comparing various soil parameters and the mobile fraction of lead, only pH shows a significant correlation. The amphoteric character of lead causes a minimum of mobility about pH 6; pH-values below are responsible for the higher mobility of lead as Pb 2+ , at pH-values above 6 soluble hydroxy and humic acid complexes are formed. (orig.) [de

Synthesis and new structure shaping mechanism of silica particles formed at high pH

International Nuclear Information System (INIS)

Zhang, Henan; Zhao, Yu; Akins, Daniel L.

2012-01-01

For the sol–gel synthesis of silica particles under high pH catalytic conditions (pH>12) in water/ethanol solvent, we have deduced that the competing dynamics of chemical etching and sol–gel process can explain the types of silica particles formed and their morphologies. We have demonstrated that emulsion droplets that are generated by adding tetraethyl orthosilicate (TEOS) to a water–ethanol solution serve as soft templates for hollow spherical silica (1–2 μm). And if the emulsion is converted by the sol–gel process, one finds that suspended solid silica spheres of diameter of ∼900 nm are formed. Moreover, several other factors are found to play fundamental roles in determining the final morphologies of silica particles, such as by variation of the pH (in our case, using OH – ) to a level where condensation dominates; by changing the volume ratios of water/ethanol; and using an emulsifier (specifically, CTAB) - Graphical abstract: “Local chemical etching” and sol–gel process have been proposed to interpret the control of morphologies of silica particles through varying initial pHs in syntheses. Highlights: ► Different initial pHs in our syntheses provides morphological control of silica particles. ► “Local chemical etching” and sol–gel process describes the formation of silica spheres. ► The formation of emulsions generates hollow silica particles.

CityMobil : Human factor issues regarding highly automated vehicles on eLane

NARCIS (Netherlands)

Toffetti, A.; Wilschut, E.S.; Martens, M.H.; Schieben, A.; Rambaldini, A.; Merat, N.; Flemisch, F.

2009-01-01

There are several human factor concerns with highly autonomous or semiautonomous driving, such as transition of control, loss of skill, and dealing with automated system errors. Four CityMobil experiments studied the eLane concept for dual-mode cars, and the results of one are described. The open

High School Pupils' Attitudes and Self-Efficacy of Using Mobile Devices

Science.gov (United States)

Nikolopoulou, Kleopatra; Gialamas, Vasilis

2017-01-01

This paper regards a study aiming to investigate junior high school pupils' attitudes and self-efficacy of using mobile devices. A 25-item questionnaire was administered to 260 pupils aged 12-15 years old, in Greece. Pupils' attitudes were positive, and four factors were extracted, "perceived usefulness", "affection",…

Research Article. The Influence of Some Parameters on Chiral Separation of Ibuprofen by High-Performance Liquid Chromatography and Capillary Electrophoresis

Directory of Open Access Journals (Sweden)

Balint Alina

2017-03-01

Full Text Available Objective: The aim of the study was to compare the influence of mobile phase composition and temperature on chiral separation of racemic ibuprofen by capillary electrophoresis and high performance liquid chromatography with UV detection. Materials and methods: Racemic ibuprofen was analysed on a chiral OVM column with an HPLC system 1100 Agilent Technologies, under isocratic elution, by using potassium dihydrogen phosphate 20 mM and ethanol in mobile phase. The flow rate was set at 1 mL/min, UV detector at 220 nm and different column temperatures were tested. For electrophoresis separation an Agilent CE G1600AX Capillary Electrophoresis System system, with UV detection, was used. The electrophoresis analysis was performed at different pH values and temperatures, with phosphate buffer 25 mM and methyl-β-cyclodextrin as chiral selector. Results: The chromatograhic analysis reveals a high influence of mobile phase pH on ibuprofen enantiomers separation. An elution with a mixture of potassium dihydrogen phosphate 20 mM pH=3 and ethanol, at 25°C, allowed enantiomers separation with good resolution in less than 8 min. Conclusions: The proposed HPLC method proved suitable for the separation of ibuprofen enantiomers with a good resolution, but the capillary electrophoresis tested parameters did not allow chiral discrimination.

Balance the Carrier Mobility To Achieve High Performance Exciplex OLED Using a Triazine-Based Acceptor.

Science.gov (United States)

Hung, Wen-Yi; Chiang, Pin-Yi; Lin, Shih-Wei; Tang, Wei-Chieh; Chen, Yi-Ting; Liu, Shih-Hung; Chou, Pi-Tai; Hung, Yi-Tzu; Wong, Ken-Tsung

2016-02-01

A star-shaped 1,3,5-triazine/cyano hybrid molecule CN-T2T was designed and synthesized as a new electron acceptor for efficient exciplex-based OLED emitter by mixing with a suitable electron donor (Tris-PCz). The CN-T2T/Tris-PCz exciplex emission shows a high ΦPL of 0.53 and a small ΔET-S = -0.59 kcal/mol, affording intrinsically efficient fluorescence and highly efficient exciton up-conversion. The large energy level offsets between Tris-PCz and CN-T2T and the balanced hole and electron mobility of Tris-PCz and CN-T2T, respectively, ensuring sufficient carrier density accumulated in the interface for efficient generation of exciplex excitons. Employing a facile device structure composed as ITO/4% ReO3:Tris-PCz (60 nm)/Tris-PCz (15 nm)/Tris-PCz:CN-T2T(1:1) (25 nm)/CN-T2T (50 nm)/Liq (0.5 nm)/Al (100 nm), in which the electron-hole capture is efficient without additional carrier injection barrier from donor (or acceptor) molecule and carriers mobilities are balanced in the emitting layer, leads to a highly efficient green exciplex OLED with external quantum efficiency (EQE) of 11.9%. The obtained EQE is 18% higher than that of a comparison device using an exciplex exhibiting a comparable ΦPL (0.50), in which TCTA shows similar energy levels but higher hole mobility as compared with Tris-PCz. Our results clearly indicate the significance of mobility balance in governing the efficiency of exciplex-based OLED. Exploiting the Tris-PCz:CN-T2T exciplex as the host, we further demonstrated highly efficient yellow and red fluorescent OLEDs by doping 1 wt % Rubrene and DCJTB as emitter, achieving high EQE of 6.9 and 9.7%, respectively.

Impact of pH and Total Soluble Solids on Enzyme Inactivation Kinetics during High Pressure Processing of Mango (Mangifera indica) Pulp.

Science.gov (United States)

Kaushik, Neelima; Nadella, Tejaswi; Rao, P Srinivasa

2015-11-01

This study was undertaken with an aim to enhance the enzyme inactivation during high pressure processing (HPP) with pH and total soluble solids (TSS) as additional hurdles. Impact of mango pulp pH (3.5, 4.0, 4.5) and TSS (15, 20, 25 °Brix) variations on the inactivation of pectin methylesterase (PME), polyphenol oxidase (PPO), and peroxidase (POD) enzymes were studied during HPP at 400 to 600 MPa pressure (P), 40 to 70 °C temperature (T), and 6- to 20-min pressure-hold time (t). The enzyme inactivation (%) was modeled using second order polynomial equations with a good fit that revealed that all the enzymes were significantly affected by HPP. Response surface and contour models predicted the kinetic behavior of mango pulp enzymes adequately as indicated by the small error between predicted and experimental data. The predicted kinetics indicated that for a fixed P and T, higher pulse pressure effect and increased isobaric inactivation rates were possible at lower levels of pH and TSS. In contrast, at a fixed pH or TSS level, an increase in P or T led to enhanced inactivation rates, irrespective of the type of enzyme. PPO and POD were found to have similar barosensitivity, whereas PME was found to be most resistant to HPP. Furthermore, simultaneous variation in pH and TSS levels of mango pulp resulted in higher enzyme inactivation at lower pH and TSS during HPP, where the effect of pH was found to be predominant than TSS within the experimental domain. Exploration of additional hurdles such as pH, TSS, and temperature for enzyme inactivation during high pressure processing of fruits is useful from industrial point of view, as these parameters play key role in preservation process design. © 2015 Institute of Food Technologists®

Effect of dissolved organic matter derived from waste amendments on the mobility of inorganic arsenic (III) in the Egyptian alluvial soil

Energy Technology Data Exchange (ETDEWEB)

Rashad, Mohamed [Land and Water Technologies Department, Arid Lands Cultivation Research Institute, City of Scientific Research and Technological Applications (SRTA-City), New Borg El-Arab, 21934 Alexandria (Egypt); Assaad, Faiz F. [Soils and Water Use Department, National Research Centre, Dokki, Cairo (Egypt); Shalaby, Elsayed A. [Environmental Studies Department, Institute of Graduate Studies and Research, Alexandria University (Egypt)

2013-07-01

Dissolved organic matter (DOM) is one of the decisive factors affecting pollutants mobility in soils receiving waste amendments. The aim of this study was to investigate the effects of DOM1 derived from agricultural solid waste (ASW) and DOM2 derived from municipal solid waste (MSW) on the mobility of inorganic arsenic (As) in two alluvial soils from the Nile River Delta. In column experiments, addition of DOM solutions significantly increased As concentration in the effluents. There was no significant difference between the two soils, the obtained results from soil2 columns revealed that DOM2 has stronger capability than DOM1 to facilitate As mobility. The pH of the studied soils is alkaline (8.1) which promoted the dissociation as well as deprotonation of DOM and as a consequence, humic substances in DOM become negatively charged organic anions, leading to their substantial competition with As for the adsorption sites on both soil surfaces. The results emphasized that in alkaline soils there is a risk of groundwater pollution in the long run by arsenic either naturally found in soil or originated at high soil pH when dissolved organic carbon (DOC) released from various organic amendments ASW and/or MSW and leached through soil profile.

Project Opalinus Clay: Sorption Data Bases For Opalinus Clay Influenced By A High pH Plume

Energy Technology Data Exchange (ETDEWEB)

Bradbury, M.H.; Baeyens, B

2004-11-01

The interaction of groundwater with the large quantities of cement/concrete used in the construction and backfilling of emplacement tunnels containing long-lived intermediate level radioactive waste may give rise to the release of a pulse of hyper alkaline fluid (pH plume) into the surrounding rock. Since the pH of this plume could remain in excess of 12.5 for tens of thousands of years, many minerals in a sedimentary host rock would be unstable leading to dissolution reactions, secondary mineral precipitation and changes in groundwater chemistry. An Opalinus day formation in the Zuercher Weinland, is under consideration by Nagra as a potential host rock for a repository of spent fuel (SF), vitrified high-level waste (HLW) from reprocessing of spent fuel and long-lived intermediate-Ievel radioactive waste (ILW). The purpose of this report is to assess the effects of the interactions between a pH plume and Opalinus day on the sorption properties of the formation and to provide appropriate sorption data bases. (author)

Experiences from Implementing a Mobile Multiplayer Real-Time Game for Wireless Networks with High Latency

Directory of Open Access Journals (Sweden)

Alf Inge Wang

2009-01-01

Full Text Available This paper describes results and experiences from designing, implementing, and testing a multiplayer real-time game over mobile networks with high latency. The paper reports on network latency and bandwidth measurements from playing the game live over GPRS, EDGE, UMTS, and WLAN using the TCP and the UDP protocols. These measurements describe the practical constraints of various wireless networks and protocols when used for mobile multiplayer game purposes. Further, the paper reports on experiences from implementing various approaches to minimize issues related to high latency. Specifically, the paper focuses on a discussion about how much of the game should run locally on the client versus on the server to minimize the load on the mobile device and obtain sufficient consistency in the game. The game was designed to reveal all kinds of implementation issues of mobile network multiplayer games. The goal of the game is for a player to push other players around and into traps where they loose their lives. The game relies heavily on collision detection between the players and game objects. The paper presents experiences from experimenting with various approaches that can be used to handle such collisions, and highlights the advantages and disadvantages of the various approaches.

Preparation of Cationic MOFs with Mobile Anions by Anion Stripping to Remove 2,4-D from Water

Directory of Open Access Journals (Sweden)

Tao Chen

2017-07-01

Full Text Available A cationic porous framework with mobile anions (MIL-101(Cr-Cl was easily and successfully synthesized by utilizing the stronger affinity of F− to Al3+ than Cr3+ in the charge-balanced framework of MIL-101(Cr. The structure, morphology and porosity of MIL-101(Cr-Cl were characterized. The obtained new materials retain the high surface area, good thermostability, and structure topology of MIL-101(Cr. With the mobile Cl− anion, MIL-101(Cr-Cl can be used as an ion-exchange material for anionic organic pollutions. In this work, 2,4-dichlorophenoxyacetic acid (2,4-D was used as a model to test the absorption performance of this new material. This new material exhibited improved adsorbability compared to that of the original metal-organic frameworks (MOFs. At the same time, this material also shows high anti-interference performance with changing solution pH.

Mobile systems development

DEFF Research Database (Denmark)

Pedersen, Ole; Kristiansen, Martin Lund; Kammersgaard, Marc N.

2007-01-01

in XP. In general, we find XP well-suited for mobile systems development projects. However, based on our experiences and an analytical comparison we propose the following modifications to XP: Make an essential design to avoid the worst time waste during refactoring. For faster development, reuse code......Development of mobile software is Surrounded by much uncertainty. Immature software platforms on mobile clients, a highly competitive market calling for innovation, efficiency and effectiveness in the development life cycle, and lacking end-user adoption are just some of the realities facing...... development teams in the mobile software industry. By taking a process view on development of mobile systems we seek to explore the strengths and limitations of eXtreme Programming (XP) in the context of mobile software development. Following an experimental approach a mobile systems development project...

Influence of 60Co gamma radiation on fluorine plasma treated enhancement-mode high-electron-mobility transistor

International Nuclear Information System (INIS)

Quan Si; Hao Yue; Ma Xiao-Hua; Yu Hui-You

2011-01-01

AlGaN/GaN depletion-mode high-electron-mobility transistor (D-HEMT) and fluorine (F) plasma treated enhancement-mode high-electron-mobility transistor (E-HEMT) are exposed to 60 Co gamma radiation with a dose of 1.6 Mrad (Si). No degradation is observed in the performance of D-HEMT. However, the maximum transconductance of E-HEMT is increased after radiation. The 2DEG density and the mobility are calculated from the results of capacitance-voltage measurement. The electron mobility decreases after fluorine plasma treatment and recovers after radiation. Conductance measurements in a frequency range from 10 kHz to 1 MHz are used to characterize the trapping effects in the devices. A new type of trap is observed in the F plasma treated E-HEMT compared with the D-HEMT, but the density of the trap decreases by radiation. Fitting of G p /ω data yields the trap densities D T = (1 − 3) × 10 12 cm −2 · eV −1 and D T = (0.2 − 0.8) × 10 12 cm −2 · eV −1 before and after radiation, respectively. The time constant is 0.5 ms-6 ms. With F plasma treatment, the trap is introduced by etch damage and degrades the electronic mobility. After 60 Co gamma radiation, the etch damage decreases and the electron mobility is improved. The gamma radiation can recover the etch damage caused by F plasma treatment. (interdisciplinary physics and related areas of science and technology)

Acclimatization to high-variance habitats does not enhance physiological tolerance of two key Caribbean corals to future temperature and pH.

Science.gov (United States)

Camp, Emma F; Smith, David J; Evenhuis, Chris; Enochs, Ian; Manzello, Derek; Woodcock, Stephen; Suggett, David J

2016-05-25

Corals are acclimatized to populate dynamic habitats that neighbour coral reefs. Habitats such as seagrass beds exhibit broad diel changes in temperature and pH that routinely expose corals to conditions predicted for reefs over the next 50-100 years. However, whether such acclimatization effectively enhances physiological tolerance to, and hence provides refuge against, future climate scenarios remains unknown. Also, whether corals living in low-variance habitats can tolerate present-day high-variance conditions remains untested. We experimentally examined how pH and temperature predicted for the year 2100 affects the growth and physiology of two dominant Caribbean corals (Acropora palmata and Porites astreoides) native to habitats with intrinsically low (outer-reef terrace, LV) and/or high (neighbouring seagrass, HV) environmental variance. Under present-day temperature and pH, growth and metabolic rates (calcification, respiration and photosynthesis) were unchanged for HV versus LV populations. Superimposing future climate scenarios onto the HV and LV conditions did not result in any enhanced tolerance to colonies native to HV. Calcification rates were always lower for elevated temperature and/or reduced pH. Together, these results suggest that seagrass habitats may not serve as refugia against climate change if the magnitude of future temperature and pH changes is equivalent to neighbouring reef habitats. © 2016 The Author(s).

High pressure effect on the color of minced cured restructured ham at different levels of drying, pH, and NaCl.

Science.gov (United States)

Bak, Kathrine Holmgaard; Lindahl, Gunilla; Karlsson, Anders H; Lloret, Elsa; Ferrini, Gabriele; Arnau, Jacint; Orlien, Vibeke

2012-03-01

Color changes of minced cured restructured ham was studied considering the effects of high pressure (HP) treatment (600MPa, 13°C, 5min), raw meat pH(24) (low, normal, high), salt content (15, 30g/kg), and drying (20%, 50% weight loss). Raw hams were selected based on pH(24) in Semimembranosus, mixed with additives, frozen, sliced, and dried using the Quick-Dry-Slice® process. Meat color (CIE 1976 L*a*b*) and reflectance spectra were measured before and after HP treatment. HP significantly increased L*, decreased a*, and decreased b* for restructured ham dried to 20% weight loss, regardless of salt content and pH(24). L* and a* were best preserved in high pH/high salt restructured ham. HP had no effect on the color of restructured ham dried to 50% weight loss. HP had no effect on the shape of reflectance curves, indicating that the pigment responsible for minced cured restructured ham color did not change due to HP. Copyright © 2011 Elsevier Ltd. All rights reserved.

Patient-Facing Mobile Apps to Treat High-Need, High-Cost Populations: A Scoping Review.

Science.gov (United States)

Singh, Karandeep; Drouin, Kaitlin; Newmark, Lisa P; Filkins, Malina; Silvers, Elizabeth; Bain, Paul A; Zulman, Donna M; Lee, Jae-Ho; Rozenblum, Ronen; Pabo, Erika; Landman, Adam; Klinger, Elissa V; Bates, David W

2016-12-19

Self-management is essential to caring for high-need, high-cost (HNHC) populations. Advances in mobile phone technology coupled with increased availability and adoption of health-focused mobile apps have made self-management more achievable, but the extent and quality of the literature supporting their use is not well defined. The purpose of this review was to assess the breadth, quality, bias, and types of outcomes measured in the literature supporting the use of apps targeting HNHC populations. Data sources included articles in PubMed and MEDLINE (National Center for Biotechnology Information), EMBASE (Elsevier), the Cochrane Central Register of Controlled Trials (EBSCO), Web of Science (Thomson Reuters), and the NTIS (National Technical Information Service) Bibliographic Database (EBSCO) published since 2008. We selected studies involving use of patient-facing iOS or Android mobile health apps. Extraction was performed by 1 reviewer; 40 randomly selected articles were evaluated by 2 reviewers to assess agreement. Our final analysis included 175 studies. The populations most commonly targeted by apps included patients with obesity, physical handicaps, diabetes, older age, and dementia. Only 30.3% (53/175) of the apps studied in the reviewed literature were identifiable and available to the public through app stores. Many of the studies were cross-sectional analyses (42.9%, 75/175), small (median number of participants=31, interquartile range 11.0-207.2, maximum 11,690), or performed by an app's developers (61.1%, 107/175). Of the 175 studies, only 36 (20.6%, 36/175) studies evaluated a clinical outcome. Most apps described in the literature could not be located on the iOS or Android app stores, and existing research does not robustly evaluate the potential of mobile apps. Whereas apps may be useful in patients with chronic conditions, data do not support this yet. Although we had 2-3 reviewers to screen and assess abstract eligibility, only 1 reviewer abstracted

Does a Mobile Phone Depression-Screening App Motivate Mobile Phone Users With High Depressive Symptoms to Seek a Health Care Professional's Help?

Science.gov (United States)

BinDhim, Nasser F; Alanazi, Eman M; Aljadhey, Hisham; Basyouni, Mada H; Kowalski, Stefan R; Pont, Lisa G; Shaman, Ahmed M; Trevena, Lyndal; Alhawassi, Tariq M

2016-06-27

The objective of disease screening is to encourage high-risk subjects to seek health care diagnosis and treatment. Mobile phone apps can effectively screen mental health conditions, including depression. However, it is not known how effective such screening methods are in motivating users to discuss the obtained results of such apps with health care professionals. Does a mobile phone depression-screening app motivate users with high depressive symptoms to seek health care professional advice? This study aimed to address this question. This was a single-cohort, prospective, observational study of a free mobile phone depression app developed in English and released on Apple's App Store. Apple App Store users (aged 18 or above) in 5 countries, that is, Australia, Canada, New Zealand (NZ), the United Kingdom (UK), and the United States (US), were recruited directly via the app's download page. The participants then completed the Patient Health Questionnaire (PHQ-9), and their depression screening score was displayed to them. If their score was 11 or above and they had never been diagnosed with depression before, they were advised to take their results to their health care professional. They were to follow up after 1 month. A group of 2538 participants from the 5 countries completed PHQ-9 depression screening with the app. Of them, 322 participants were found to have high depressive symptoms and had never been diagnosed with depression, and received advice to discuss their results with health care professionals. About 74% of those completed the follow-up; approximately 38% of these self-reported consulting their health care professionals about their depression score. Only positive attitude toward depression as a real disease was associated with increased follow-up response rate (odds ratio (OR) 3.2, CI 1.38-8.29). A mobile phone depression-screening app motivated some users to seek a depression diagnosis. However, further study should investigate how other app users use

Assessment of heavy metal mobility in mine tailings in the province of Huelva; Evaluacion de la movilidad de metales pesados en residuos mineros de flotacion de mineria metalica en la provincia de Huelva

Energy Technology Data Exchange (ETDEWEB)

Arranz Gonzalez, J. C.; Cala Rivero, V.

2011-07-01

Metallurgic mine wastes often contain high concentrations of potentially toxic elements, the mobility of which may pose an environmental hazard for water and surrounding ecosystems. We have examined the mobility of Ag, As, Cu, Pb and Zn from composite surface samples (0-20 cm) of different pyritic tailings impoundments in the province of Huelva (Spain). These samples were also subject to physical chemical and mineralogical (XRD) characterization. The total metal content of the tailings ranged between 1.89-11.2 ppm for Ag, 72-610 ppm for As, 245-1194 ppm for Cu, 220-11933 for Pb and 41-706 for Zn, all proving to be highly acidic. The mobility of these elements was assessed by using a seven-step sequential extraction procedure and applying the toxicity characteristic leaching procedure (TCLP). We investigated the applicability of TCLP to the tailings by comparing the results with those of the first steps of the sequential extraction procedure. It was found that the pH values remained buffered (close to 4.97) upon adding the TCLP extraction reagent and that the pH values differed significantly from those of the aqueous extracts. This could result in an underestimation of mobile forms compared with those dissolved in water. We may also conclude that due to the presence of specific minerals or to the preference of some elements for acetate ions the results of any assessment of metal mobility in pyritic tailings using the TCLP test may be questionable. (Author) 42 refs.

Do earthworms impact metal mobility and availability in soil? - A review

International Nuclear Information System (INIS)

Sizmur, Tom; Hodson, Mark E.

2009-01-01

The importance of earthworms to ecosystem functioning has led to many studies on the impacts of metals on earthworms. Far less attention has been paid to the impact that earthworms have on soil metals both in terms of metal mobility and availability. In this review we consider which earthworms have been used in such studies, which soil components have been investigated, which types of soil have been used and what measures of mobility and availability applied. We proceed to review proposed reasons for effects: changes in microbial populations, pH, dissolved organic carbon and metal speciation. The balance of evidence suggests that earthworms increase metal mobility and availability but more studies are required to determine the precise mechanism for this. - We review the impact of earthworms on metal mobility and availability and suggest areas for further investigation.

Performance improvement for solution-processed high-mobility ZnO thin-film transistors

International Nuclear Information System (INIS)

Li Chensha; Loutfy, Rafik O; Li Yuning; Wu Yiliang; Ong, Beng S

2008-01-01

The fabrication technology of stable, non-toxic, transparent, high performance zinc oxide (ZnO) thin-film semiconductors via the solution process was investigated. Two methods, which were, respectively, annealing a spin-coated precursor solution and annealing a drop-coated precursor solution, were compared. The prepared ZnO thin-film semiconductor transistors have well-controlled, preferential crystal orientation and exhibit superior field-effect performance characteristics. But the ZnO thin-film transistor (TFT) fabricated by annealing a drop-coated precursor solution has a distinctly elevated linear mobility, which further approaches the saturated mobility, compared with that fabricated by annealing a spin-coated precursor solution. The performance of the solution-processed ZnO TFT was further improved when substituting the spin-coating process by the drop-coating process

Performance improvement for solution-processed high-mobility ZnO thin-film transistors

Energy Technology Data Exchange (ETDEWEB)

Li Chensha; Loutfy, Rafik O [Department of Chemical Engineering, McMaster University, 1280 Main Street West, Hamilton, Ontario L8S 4L7 (Canada); Li Yuning; Wu Yiliang; Ong, Beng S [Materials Design and Integration Laboratory, Xerox Research Centre of Canada, 2660 Speakman Drive, Mississauga, Ontario L5K 2L1 (Canada)], E-mail: lichnsa@163.com

2008-06-21

The fabrication technology of stable, non-toxic, transparent, high performance zinc oxide (ZnO) thin-film semiconductors via the solution process was investigated. Two methods, which were, respectively, annealing a spin-coated precursor solution and annealing a drop-coated precursor solution, were compared. The prepared ZnO thin-film semiconductor transistors have well-controlled, preferential crystal orientation and exhibit superior field-effect performance characteristics. But the ZnO thin-film transistor (TFT) fabricated by annealing a drop-coated precursor solution has a distinctly elevated linear mobility, which further approaches the saturated mobility, compared with that fabricated by annealing a spin-coated precursor solution. The performance of the solution-processed ZnO TFT was further improved when substituting the spin-coating process by the drop-coating process.

Gate less-FET pH Sensor Fabricated on Undoped AlGaN/ GaN HEMT Structure

International Nuclear Information System (INIS)

Maneea Eizadi Sharifabad; Mastura Shafinaz Zainal Abidin; Shaharin Fadzli Abd Rahman; Abdul Manaf Hashim; Abdul Rahim Abdul Rahman

2011-01-01

Gallium nitride with wurtzite crystal structure is a chemically stable semiconductor with high internal spontaneous and piezoelectric polarization, which make it highly suitable materials to create very sensitive and robust sensors for the detection of ions, gases and liquids. Sensing characteristics of an open-gate liquid-phase sensor fabricated on undoped-AlGaN/ GaN high-electron-mobility-transistor (HEMT) structure in aqueous solution was investigated. In ambient atmosphere, the open-gate undoped AlGaN/ GaN HEMT clearly showed only the presence of linear region of currents while Si-doped AlGaN/ GaN showed the linear and saturation regions of currents, very similar to those of gated devices. This seems to show that very low Fermi level pinning by surface states exists in undoped AlGaN/ GaN sample. In aqueous solution, the typical current-voltage (I-V) characteristics of HEMTs with good gate controllability were observed. The potential of the AlGaN surface at the open-gate area is effectively controlled via aqueous solution by Ag/ AgCl reference gate electrode. The open-gate undoped AlGaN/ GaN HEMT structure is capable of stable operation in aqueous electrolytes and exhibit linear sensitivity, and high sensitivity of 1.9 mA/ pH or 3.88 mA/ mm/ pH at drain-source voltage, VDS = 5 V was obtained. Due to large leakage current where it increases with the negative reference gate voltage, the Nernstians like sensitivity cannot be determined. Suppression of current leakage is likely to improve the device performance. The open-gate undoped-AlGaN/ GaN structure is expected to be suitable for pH sensing application. (author)

Optical pH Sensor Covering the Range from pH 0-14 Compatible with Mobile-Device Readout and Based on a Set of Rationally Designed Indicator Dyes.

Science.gov (United States)

Gotor, Raúl; Ashokkumar, Pichandi; Hecht, Mandy; Keil, Karin; Rurack, Knut

2017-08-15

In this work, a family of pH-responsive fluorescent probes has been designed in a rational manner with the aid of quantum chemistry tools, covering the entire pH range from 0-14. Relying on the boron-dipyrromethene (BODIPY) core, all the probes as well as selected reference dyes display very similar spectroscopic properties with ON-OFF fluorescence switching responses, facilitating optical readout in simple devices used for detection and analysis. Embedding of the probes and reference dyes into hydrogel spots on a plastic strip yielded a test strip that reversibly indicates pH with a considerably small uncertainty of ∼0.1 pH units. These strips are not only reusable but, combined with a 3D-printed case that can be attached to a smartphone, the USB port of which drives the integrated LED used for excitation, allows for autonomous operation in on-site or in-the-field applications; the developed Android application software ("app") further simplifies operation for unskilled users.

pH Mapping on Tooth Surfaces for Quantitative Caries Diagnosis Using Micro Ir/IrOx pH Sensor.

Science.gov (United States)

Ratanaporncharoen, Chindanai; Tabata, Miyuki; Kitasako, Yuichi; Ikeda, Masaomi; Goda, Tatsuro; Matsumoto, Akira; Tagami, Junji; Miyahara, Yuji

2018-04-03

A quantitative diagnostic method for dental caries would improve oral health, which directly affects the quality of life. Here we describe the preparation and application of Ir/IrOx pH sensors, which are used to measure the surface pH of dental caries. The pH level is used as an indicator to distinguish between active and arrested caries. After a dentist visually inspected and defined 18 extracted dentinal caries at various positions as active or arrested caries, the surface pH values of sound and caries areas were directly measured with an Ir/IrOx pH sensor with a diameter of 300 μm as a dental explorer. The average pH values of the sound root, the arrested caries, and active caries were 6.85, 6.07, and 5.30, respectively. The pH obtained with an Ir/IrOx sensor was highly correlated with the inspection results by the dentist, indicating that the types of caries were successfully categorized. This caries testing technique using a micro Ir/IrOx pH sensor provides an accurate quantitative caries evaluation and has potential in clinical diagnosis.

Considering the Geographic Dispersion of Homeless and Highly Mobile Students and Families

Science.gov (United States)

Miller, Peter M.; Bourgeois, Alexis K.

2013-01-01

This article addresses school and community-level issues associated with the expanding crisis of student homelessness in the United States. We note that while an increased geographic dispersion of homeless and highly mobile (HHM) families is largely attributed to the widespread effects of the economic recession, it is also furthered by shifting…

pH sensitive quantum dot-anthraquinone nanoconjugates

Science.gov (United States)

Ruedas-Rama, Maria Jose; Hall, Elizabeth A. H.

2014-05-01

Semiconductor quantum dots (QDs) have been shown to be highly sensitive to electron or charge transfer processes, which may alter their optical properties. This feature can be exploited for different sensing applications. Here, we demonstrate that QD-anthraquinone conjugates can function as electron transfer-based pH nanosensors. The attachment of the anthraquinones on the surface of QDs results in the reduction of electron hole recombination, and therefore a quenching of the photoluminescence intensity. For some anthraquinone derivatives tested, the quenching mechanism is simply caused by an electron transfer process from QDs to the anthraquinone, functioning as an electron acceptor. For others, electron transfer and energy transfer (FRET) processes were found. A detailed analysis of the quenching processes for CdSe/ZnS QD of two different sizes is presented. The photoluminescence quenching phenomenon of QDs is consistent with the pH sensitive anthraquinone redox chemistry. The resultant family of pH nanosensors shows pKa ranging ˜5-8, being ideal for applications of pH determination in physiological samples like blood or serum, for intracellular pH determination, and for more acidic cellular compartments such as endosomes and lysosomes. The nanosensors showed high selectivity towards many metal cations, including the most physiologically important cations which exist at high concentration in living cells. The reversibility of the proposed systems was also demonstrated. The nanosensors were applied in the determination of pH in samples mimicking the intracellular environment. Finally, the possibility of incorporating a reference QD to achieve quantitative ratiometric measurements was investigated.

pH sensitive quantum dot–anthraquinone nanoconjugates

International Nuclear Information System (INIS)

Ruedas-Rama, Maria Jose; Hall, Elizabeth A H

2014-01-01

Semiconductor quantum dots (QDs) have been shown to be highly sensitive to electron or charge transfer processes, which may alter their optical properties. This feature can be exploited for different sensing applications. Here, we demonstrate that QD-anthraquinone conjugates can function as electron transfer-based pH nanosensors. The attachment of the anthraquinones on the surface of QDs results in the reduction of electron hole recombination, and therefore a quenching of the photoluminescence intensity. For some anthraquinone derivatives tested, the quenching mechanism is simply caused by an electron transfer process from QDs to the anthraquinone, functioning as an electron acceptor. For others, electron transfer and energy transfer (FRET) processes were found. A detailed analysis of the quenching processes for CdSe/ZnS QD of two different sizes is presented. The photoluminescence quenching phenomenon of QDs is consistent with the pH sensitive anthraquinone redox chemistry. The resultant family of pH nanosensors shows pK a ranging ∼5–8, being ideal for applications of pH determination in physiological samples like blood or serum, for intracellular pH determination, and for more acidic cellular compartments such as endosomes and lysosomes. The nanosensors showed high selectivity towards many metal cations, including the most physiologically important cations which exist at high concentration in living cells. The reversibility of the proposed systems was also demonstrated. The nanosensors were applied in the determination of pH in samples mimicking the intracellular environment. Finally, the possibility of incorporating a reference QD to achieve quantitative ratiometric measurements was investigated

Effects of inositol trisphosphate on calcium mobilization in high-voltage and saponin-permeabilized platelets

International Nuclear Information System (INIS)

Gear, A.R.L.; Hallam, T.J.

1986-01-01

Interest in phosphatidylinositol metabolism has been greatly stimulated by the findings that diglyceride and inositol phosphates may serve as second messengers in modulating cellular function. Formation of 1,4,5-inositol trisphosphate (IP 3 ), in particular, has been linked to mobilization of intracellular calcium in a number of cell types. The authors have examined the ability of IP 3 to mobilize calcium in human platelets permeabilized by either saponin or high-voltage discharge. Saponin at 15 μg/ml effectively permeabilized platelets to exogenous inositol 1,4,5-trisphosphate which released bound [ 45 Ca] within 1 min and with a Ka of 7.4 +/- 4.1 μM. A small (25%) azide-sensitive pool was also responsive to inositol trisphosphate. The calcium pools were completely discharged by A-23187 and the ATP-dependent uptake was prevented by dinitrophenol. In contrast to the result with saponin, platelets accessed by high-voltage discharge were insensitive to challenge by inositol 1,4,5-trisphosphate. The data suggest that while inositol 1,4,5-trisphosphate can rapidly mobilize platelet calcium, the ability to demonstrate this depends on the method of permeabilization

Corrosion behavior of reinforcing steel in concrete for nuclear facilities exposed in high chloride and low pH environment

International Nuclear Information System (INIS)

Nishimura, Toshiyasu; Raman, Vedarajan

2010-01-01

The Cl ion concentration and pH were monitored by inserting micro-electrodes into artificial pores in the mortar which was exposed in 0.5 mol/l chloride solution (pH 4.0). At the same time, the electrochemical behavior of the reinforcing steel was investigated by EIS. The Cl ion concentration in the mortar was obtained using Ag/AgCl micro-electrodes, showing that this behavior is generally controlled by diffusion. When the diffusion equation was used in this work, the diffusion coefficient (D c ) showed a high value of D c = 9.5 x 10 -5 mm 2 /s. Similarly, the pH in the mortar was obtained using W/WO x micro-electrodes. With a 10 mm cover thickness, pH continued to decrease to pH 8.0, which was considered by penetration of H + ions from the surface. Based on the results of monitoring with the micro-electrodes, solutions simulating those in the pores in mortar were prepared and used in EIS measurements. The charge transfer resistance R ct in the simulated solutions showed good correspondence with the impedance Z (Z 1mHz -Z sol ) in the actual mortar. This is attributed to the fact that the corrosion of reinforcing steel was controlled by the solution conditions (mainly Cl concentration and pH) in the pores in mortar.

Using Mobile Communication Technology in High School Education: Motivation, Pressure, and Learning Performance

Science.gov (United States)

Rau, Pei-Luen Patrick; Gao, Qin; Wu, Li-Mei

2008-01-01

Motivation and pressure are considered two factors impacting vocational senior high school student learning. New communication technology, especially mobile communication technology, is supposed to be effective in encouraging interaction between the student and the instructor and improving learning efficiency. Social presence and information…

From computational discovery to experimental characterization of a high hole mobility organic crystal.

KAUST Repository

Sokolov, Anatoliy N; Atahan-Evrenk, Sule; Mondal, Rajib; Akkerman, Hylke B; Sá nchez-Carrera, Roel S; Granados-Focil, Sergio; Schrier, Joshua; Mannsfeld, Stefan C B; Zoombelt, Arjan P; Bao, Zhenan; Aspuru-Guzik, Alá n

2011-01-01

can be hindered by synthetic and characterization difficulties. Here we show that in silico screening of novel derivatives of the dinaphtho[2,3-b:2',3'-f]thieno[3,2-b]thiophene semiconductor with high hole mobility and air stability can lead

N-polar GaN epitaxy and high electron mobility transistors

International Nuclear Information System (INIS)

Wong, Man Hoi; Keller, Stacia; Dasgupta, Nidhi Sansaptak; Denninghoff, Daniel J; Kolluri, Seshadri; Brown, David F; Lu, Jing; Fichtenbaum, Nicholas A; Ahmadi, Elaheh; DenBaars, Steven P; Speck, James S; Mishra, Umesh K; Singisetti, Uttam; Chini, Alessandro; Rajan, Siddharth

2013-01-01

This paper reviews the progress of N-polar (0001-bar) GaN high frequency electronics that aims at addressing the device scaling challenges faced by GaN high electron mobility transistors (HEMTs) for radio-frequency and mixed-signal applications. Device quality (Al, In, Ga)N materials for N-polar heterostructures are developed using molecular beam epitaxy and metalorganic chemical vapor deposition. The principles of polarization engineering for designing N-polar HEMT structures will be outlined. The performance, scaling behavior and challenges of microwave power devices as well as highly-scaled depletion- and enhancement-mode devices employing advanced technologies including self-aligned processes, n+ (In,Ga)N ohmic contact regrowth and high aspect ratio T-gates will be discussed. Recent research results on integrating N-polar GaN with Si for prospective novel applications will also be summarized. (invited review)

A geostationary satellite system for mobile multimedia applications using portable, aeronautical and mobile terminals

Science.gov (United States)

Losquadro, G.; Luglio, M.; Vatalaro, F.

1997-01-01

A geostationary satellite system for mobile multimedia services via portable, aeronautical and mobile terminals was developed within the framework of the Advanced Communications Technology Service (ACTS) programs. The architecture of the system developed under the 'satellite extremely high frequency communications for multimedia mobile services (SECOMS)/ACTS broadband aeronautical terminal experiment' (ABATE) project is presented. The system will be composed of a Ka band system component, and an extremely high frequency band component. The major characteristics of the space segment, the ground control station and the portable, aeronautical and mobile user terminals are outlined.

Proton NMR investigation of heme pocket mobility in hemoglobin via hydrogen isotope exchange kinetics

International Nuclear Information System (INIS)

Han, K.

1985-01-01

Dynamic mobility of heme cavity, the active site of Hb, was investigated by analyzing the hydrogen isotope exchange kinetics of the proximal histidyl ring NH of various kinds of Hbs with the aid of the high field Fourier Transform 1 H NMR spectroscopy. The exchange reaction occurs faster in oxy or R-state Hb than in deoxy or T-state Hb and there exists a good correlation between the oxygen affinity of Hb and the heme pocket mobility reflected in the hydrogen exchange rate. The effect of pH on the exchange is dramatically different for the two subunits of Hb A. Studying the exchange characteristics of mutant Hbs and chemically modified Hbs not only showed the existence of three well-defined localized paths for transmission of conformational changes between different heme pockets through a 1 b 2 subunit interface, but also indicated that the heme pocket mobility is regulated by the quaternary state of Hb as well as by the ligation state of Hb. Finally, the effect of the quaternary state on the heme pocket mobility is separated from that of the ligation by following the exchange reactions in Hbs where only their quaternary structure transition can be achieved without changing their ligation states by adjusting experimental conditions such as adding inositol hexaphosphate

Environmental stability of high-mobility indium-oxide based transparent electrodes

Directory of Open Access Journals (Sweden)

Thanaporn Tohsophon

2015-11-01

Full Text Available Large-scale deployment of a wide range of optoelectronic devices, including solar cells, critically depends on the long-term stability of their front electrodes. Here, we investigate the performance of Sn-doped In2O3 (ITO, H-doped In2O3 (IO:H, and Zn-doped In2O3 (IZO electrodes under damp heat (DH conditions (85 °C, 85% relative humidity. ITO, IO:H capped with ITO, and IZO show high stability with only 3%, 9%, and 13% sheet resistance (Rs degradation after 1000 h of DH, respectively. For uncapped IO:H, we find a 75% Rs degradation, due to losses in electron Hall mobility (μHall. We propose that this degradation results from chemisorbed OH- or H2O-related species in the film, which is confirmed by thermal desorption spectroscopy and x-ray photoelectron spectroscopy. While μHall strongly degrades during DH, the optical mobility (μoptical remains unchanged, indicating that the degradation mainly occurs at grain boundaries.

Clinical Value of High Mobility Group Box 1 and the Receptor for Advanced Glycation End-products in Head and Neck Cancer: A Systematic Review

Directory of Open Access Journals (Sweden)

Nguyen, Austin

2016-04-01

Full Text Available Introduction High mobility group box 1 is a versatile protein involved in gene transcription, extracellular signaling, and response to inflammation. Extracellularly, high mobility group box 1 binds to several receptors, notably the receptor for advanced glycation end-products. Expression of high mobility group box 1 and the receptor for advanced glycation end-products has been described in many cancers. Objectives To systematically review the available literature using PubMed and Web of Science to evaluate the clinical value of high mobility group box 1 and the receptor for advanced glycation end-products in head and neck squamous cell carcinomas. Data synthesis A total of eleven studies were included in this review. High mobility group box 1 overexpression is associated with poor prognosis and many clinical and pathological characteristics of head and neck squamous cell carcinomas patients. Additionally, the receptor for advanced glycation end-products demonstrates potential value as a clinical indicator of tumor angiogenesis and advanced staging. In diagnosis, high mobility group box 1 demonstrates low sensitivity. Conclusion High mobility group box 1 and the receptor for advanced glycation end-products are associated with clinical and pathological characteristics of head and neck squamous cell carcinomas. Further investigation of the prognostic and diagnostic value of these molecules is warranted.

A comparative study on oxidative stress response in the hepatopancreas and midgut of the white shrimp Litopenaeus vannamei under gradual changes to low or high pH environment.

Science.gov (United States)

Han, Si-Yin; Wang, Meng-Qiang; Wang, Bao-Jie; Liu, Mei; Jiang, Ke-Yong; Wang, Lei

2018-05-01

White shrimp Litopenaeus vannamei were reared under conditions of gradual changes to a low pH (gradual-low pH, 6.65-8.20) or a high pH (gradual-high pH, 8.20-9.81) versus a normal pH environment (8.14-8.31) during a 28-day period. Survival of shrimp, and ROS production, antioxidant responses and oxidative damage in the hepatopancreas and midgut were investigated. Consequently, shrimp enhanced MnSOD, GPx, and Hsp70 transcripts as early defense mechanism in the hepatopancreas and midgut to scavenge excessive ROS during short-term (≤ 7 days) gradual-low and high pH stress. Meanwhile, the hepatopancreas was more sensitive to ROS than midgut because of earlier ROS production increase, antioxidant response and oxidative damage. Then, suppressed antioxidant response in the hepatopancreas and midgut of shrimp suggested a loss of antioxidant regulatory capacity caused by aggravated oxidative damage after long-term (≥ 14 days) gradual-high pH stress, leading to continuous death. However, enhanced GPx, GST, and Hsp70 transcripts in the hepatopancreas and midgut might be long-term(≥ 14 days) antioxidant adaptation mechanism of shrimp to gradual-low pH stress, which could prevent further ROS perturbation and weaken oxidative damage to achieve a new immune homeostasis, contributing to stable survival rate. Therefore, we have a few insights that it is necessary to protect hepatopancreas for controlling shrimp death under gradual-high pH stress. Copyright © 2018 Elsevier Ltd. All rights reserved.

Quantum calculations of the carrier mobility: Methodology, Matthiessen's rule, and comparison with semi-classical approaches

Energy Technology Data Exchange (ETDEWEB)

Niquet, Yann-Michel, E-mail: yniquet@cea.fr; Nguyen, Viet-Hung; Duchemin, Ivan [L-Sim, SP2M, UMR-E CEA/UJF-Grenoble 1, INAC, Grenoble (France); Triozon, François [CEA, LETI-MINATEC, Grenoble (France); Nier, Olivier; Rideau, Denis [ST Microelectronics, Crolles (France)

2014-02-07

We discuss carrier mobilities in the quantum Non-Equilibrium Green's Functions (NEGF) framework. We introduce a method for the extraction of the mobility that is free from contact resistance contamination and with minimal needs for ensemble averages. We focus on silicon thin films as an illustration, although the method can be applied to various materials such as semiconductor nanowires or carbon nanostructures. We then introduce a new paradigm for the definition of the partial mobility μ{sub M} associated with a given elastic scattering mechanism “M,” taking phonons (PH) as a reference (μ{sub M}{sup −1}=μ{sub PH+M}{sup −1}−μ{sub PH}{sup −1}). We argue that this definition makes better sense in a quantum transport framework as it is free from long range interference effects that can appear in purely ballistic calculations. As a matter of fact, these mobilities satisfy Matthiessen's rule for three mechanisms [e.g., surface roughness (SR), remote Coulomb scattering (RCS) and phonons] much better than the usual, single mechanism calculations. We also discuss the problems raised by the long range spatial correlations in the RCS disorder. Finally, we compare semi-classical Kubo-Greenwood (KG) and quantum NEGF calculations. We show that KG and NEGF are in reasonable agreement for phonon and RCS, yet not for SR. We discuss the reasons for these discrepancies.

Mechanisms of intragastric pH sensing.

Science.gov (United States)

Goo, Tyralee; Akiba, Yasutada; Kaunitz, Jonathan D

2010-12-01

Luminal amino acids and lack of luminal acidity as a result of acid neutralization by intragastric foodstuffs are powerful signals for acid secretion. Although the hormonal and neural pathways underlying this regulatory mechanism are well understood, the nature of the gastric luminal pH sensor has been enigmatic. In clinical studies, high pH, tryptic peptides, and luminal divalent metals (Ca(2+) and Mg(2+)) increase gastrin release and acid production. The calcium-sensing receptor (CaSR), first described in the parathyroid gland but expressed on gastric G cells, is a logical candidate for the gastric acid sensor. Because CaSR ligands include amino acids and divalent metals, and because extracellular pH affects ligand binding in the pH range of the gastric content, its pH, metal, and nutrient-sensing functions are consistent with physiologic observations. The CaSR is thus an attractive candidate for the gastric luminal sensor that is part of the neuroendocrine negative regulatory loop for acid secretion.

Transfer and mobility of trace metallic elements in the sedimentary column of continental hydro-systems

International Nuclear Information System (INIS)

Devallois, V.

2009-02-01

In freshwater systems, trace metal pollutants are transferred into water and sedimentary columns under dissolved forms and/or fixed onto solid particles. Accumulated in the sedimentary areas, these latter ones can constitute important stocks of materials and associated pollutants and may impair water quality when environmental changes lead to increase their mobility. The mobility of the stocks of pollutants is mainly depending on the erosion, on the interstitial diffusion of the mobile phases (dissolved and colloidal) and on the bioturbation. In this context, this study involves the analysis of the mobility by interstitial diffusion. This topic consists in studying trace metal fractionation between their mobile (dissolved and colloidal) and non mobile (fixed onto the particles) forms. This point is governed by sorption/desorption processes at the particle surfaces. These processes are regulated by physico-chemical parameters (pH, redox potential, ionic strength...) and are influenced by biogeochemical reactions resulting from the oxidation of the organic matter by the microbial activity. These reactions generate vertical profiles of nutrients and metal concentrations along the sedimentary column. To understand these processes, this work is based on a mixed approach that combines in situ, analysis and modelling. In situ experimental part consists in sampling natural sediments cores collected at 4 different sites (1 site in Durance and 3 sites on the Rhone). These samples are analyzed according to an analytical protocol that provides the vertical distribution of physicochemical parameters (pH, redox potential, size distribution, porosity), nutrients and solid - liquid forms of trace metals (cobalt, copper, nickel, lead, zinc). The analysis and interpretation of these experimental results are based on a model that was developed during this study and that includes: 1) model of interstitial diffusion (Boudreau, 1997), 2) biogeochemical model (Wang and Van Cappellen

Accurate on-chip measurement of the Seebeck coefficient of high mobility small molecule organic semiconductors

Science.gov (United States)

Warwick, C. N.; Venkateshvaran, D.; Sirringhaus, H.

2015-09-01

We present measurements of the Seebeck coefficient in two high mobility organic small molecules, 2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene (C8-BTBT) and 2,9-didecyl-dinaphtho[2,3-b:2',3'-f]thieno[3,2-b]thiophene (C10-DNTT). The measurements are performed in a field effect transistor structure with high field effect mobilities of approximately 3 cm2/V s. This allows us to observe both the charge concentration and temperature dependence of the Seebeck coefficient. We find a strong logarithmic dependence upon charge concentration and a temperature dependence within the measurement uncertainty. Despite performing the measurements on highly polycrystalline evaporated films, we see an agreement in the Seebeck coefficient with modelled values from Shi et al. [Chem. Mater. 26, 2669 (2014)] at high charge concentrations. We attribute deviations from the model at lower charge concentrations to charge trapping.

Effect of temperature, gas phase composition, pH and microbial activity on As, Zn, Pb and Cd mobility in selected soils in the Ebro and Meuse Basins in the context of global change

Energy Technology Data Exchange (ETDEWEB)

Joubert, A.V.P. [Laboratoire des Interactions Micro-organismes, Mineraux et Matieres organiques dans les Sols (LIMOS) UMR 7137, Nancy University, CNRS, BP 239, 54506 Vandoeuvre-les-Nancy cedex (France)]. E-mail: antoine.joubert@limos.uhp-nancy.fr; Lucas, L. [Bureau de Recherches Geologiques et Minieres (BRGM), Service Environnement et Procedes Innovants-Unite Ecotechnologie (EPI/ECO), 3 Avenue Claude Guillemin, BP 6009, 45060 Orleans cedex 2 (France); Garrido, F. [Bureau de Recherches Geologiques et Minieres (BRGM), Service Environnement et Procedes Innovants-Unite Ecotechnologie (EPI/ECO), 3 Avenue Claude Guillemin, BP 6009, 45060 Orleans cedex 2 (France)]. E-mail: f.garrido@brgm.fr; Joulian, C. [Bureau de Recherches Geologiques et Minieres (BRGM), Service Environnement et Procedes Innovants-Unite Ecotechnologie (EPI/ECO), 3 Avenue Claude Guillemin, BP 6009, 45060 Orleans cedex 2 (France); Jauzein, M. [Laboratoire des Interactions Micro-organismes, Mineraux et Matieres organiques dans les Sols (LIMOS) UMR 7137, Nancy University, CNRS, BP 239, 54506 Vandoeuvre-les-Nancy cedex (France)

2007-08-15

This study estimates the effect of environmental parameters on the mobility of four inorganic contaminants (As, Zn, Pb and Cd) in soils from three areas in the Ebro and Meuse River basins, within the context of global change. An experimental method, applicable to various soil systems, is used to measure the effect of four global-change-sensitive parameters (temperature, gas phase composition, pH and microbial activity). The aqueous phase of batch incubations was sampled regularly to monitor toxic element concentrations in water. Statistical processing enabled discrimination of the most relevant variations in dissolved concentrations measured at different incubation times and under different experimental conditions. Gas phase composition was identified as the most sensitive parameter for toxic element solubilization. This study confirms that total soil concentrations of inorganic pollutants are irrelevant when assessing the hazard for ecosystems or water resource quality. - An experimental method applicable for different soil systems enables the determination of the effect of environmental parameters, potentially affected by global change, on the mobilization of inorganic pollutants.

Low-Frequency Noise in Layered ReS2 Field Effect Transistors on HfO2 and Its Application for pH Sensing.

Science.gov (United States)

Liao, Wugang; Wei, Wei; Tong, Yu; Chim, Wai Kin; Zhu, Chunxiang

2018-02-28

Layered rhenium disulfide (ReS 2 ) field effect transistors (FETs), with thickness ranging from few to dozens of layers, are demonstrated on 20 nm thick HfO 2 /Si substrates. A small threshold voltage of -0.25 V, high on/off current ratio of up to ∼10 7 , small subthreshold swing of 116 mV/dec, and electron carrier mobility of 6.02 cm 2 /V·s are obtained for the two-layer ReS 2 FETs. Low-frequency noise characteristics in ReS 2 FETs are analyzed for the first time, and it is found that the carrier number fluctuation mechanism well describes the flicker (1/f) noise of ReS 2 FETs with different thicknesses. pH sensing using a two-layer ReS 2 FET with HfO 2 as a sensing oxide is then demonstrated with a voltage sensitivity of 54.8 mV/pH and a current sensitivity of 126. The noise characteristics of the ReS 2 FET-based pH sensors are also examined, and a corresponding detection limit of 0.0132 pH is obtained. Our studies suggest the high potential of ReS 2 for future low-power nanoelectronics and biosensor applications.

A survey study of the association between mobile phone use and daytime sleepiness in California high school students.

Science.gov (United States)

Nathan, Nila; Zeitzer, Jamie

2013-09-12

Mobile phone use is near ubiquitous in teenagers. Paralleling the rise in mobile phone use is an equally rapid decline in the amount of time teenagers are spending asleep at night. Prior research indicates that there might be a relationship between daytime sleepiness and nocturnal mobile phone use in teenagers in a variety of countries. As such, the aim of this study was to see if there was an association between mobile phone use, especially at night, and sleepiness in a group of U.S. teenagers. A questionnaire containing an Epworth Sleepiness Scale (ESS) modified for use in teens and questions about qualitative and quantitative use of the mobile phone was completed by students attending Mountain View High School in Mountain View, California (n = 211). Multivariate regression analysis indicated that ESS score was significantly associated with being female, feeling a need to be accessible by mobile phone all of the time, and a past attempt to reduce mobile phone use. The number of daily texts or phone calls was not directly associated with ESS. Those individuals who felt they needed to be accessible and those who had attempted to reduce mobile phone use were also ones who stayed up later to use the mobile phone and were awakened more often at night by the mobile phone. The relationship between daytime sleepiness and mobile phone use was not directly related to the volume of texting but may be related to the temporal pattern of mobile phone use.

Dynamic regulation of gastric surface pH by luminal pH

OpenAIRE

Chu, Shaoyou; Tanaka, Shin; Kaunitz, Jonathan D.; Montrose, Marshall H.

1999-01-01

In vivo confocal imaging of the mucosal surface of rat stomach was used to measure pH noninvasively under the mucus gel layer while simultaneously imaging mucus gel thickness and tissue architecture. When tissue was superfused at pH 3, the 25 μm adjacent to the epithelial surface was relatively alkaline (pH 4.1 ± 0.1), and surface alkalinity was enhanced by topical dimethyl prostaglandin E2 (pH 4.8 ± 0.2). Luminal pH was changed from pH 3 to pH 5 to mimic the fasted-to-fed transition in intra...

Elevated naturally occurring arsenic in a semiarid oxidizing system, Southern High Plains aquifer, Texas, USA

International Nuclear Information System (INIS)

Scanlon, B.R.; Nicot, J.P.; Reedy, R.C.; Kurtzman, D.; Mukherjee, A.; Nordstrom, D.K.

2009-01-01

High groundwater As concentrations in oxidizing systems are generally associated with As adsorption onto hydrous metal (Al, Fe or Mn) oxides and mobilization with increased pH. The objective of this study was to evaluate the distribution, sources and mobilization mechanisms of As in the Southern High Plains (SHP) aquifer, Texas, relative to those in other semiarid, oxidizing systems. Elevated groundwater As levels are widespread in the southern part of the SHP (SHP-S) aquifer, with 47% of wells exceeding the current EPA maximum contaminant level (MCL) of 10 μg/L (range 0.3-164 μg/L), whereas As levels are much lower in the north (SHP-N: 9% ≥ As MCL of 10 μg/L; range 0.2-43 μg/L). The sharp contrast in As levels between the north and south coincides with a change in total dissolved solids (TDS) from 395 mg/L (median north) to 885 mg/L (median south). Arsenic is present as arsenate (As V) in this oxidizing system and is correlated with groundwater TDS (Spearman's ρ = 0.57). The most likely current source of As is sorbed As onto hydrous metal oxides based on correlations between As and other oxyanion-forming elements (V, ρ = 0.88; Se, ρ = 0.54; B, ρ = 0.51 and Mo, ρ = 0.46). This source is similar to that in other oxidizing systems and constitutes a secondary source; the most likely primary source being volcanic ashes in the SHP aquifer or original source rocks in the Rockies, based on co-occurrence of As and F (ρ = 0.56), oxyanion-forming elements and SiO 2 (ρ = 0.41), which are found in volcanic ashes. High groundwater As concentrations in some semiarid oxidizing systems are related to high evaporation. Although correlation of As with TDS in the SHP aquifer may suggest evaporative concentration, unenriched stable isotopes (δ 2 H: -65 to -27; δ 18 O: -9.1 to -4.2) in the SHP aquifer do not support evaporation. High TDS in the SHP aquifer is most likely related to upward movement of saline water from the underlying Triassic Dockum aquifer. Mobilization

Resveratrol-induced apoptosis is enhanced in low pH environments associated with cancer.

Science.gov (United States)

Shamim, Uzma; Hanif, Sarmad; Albanyan, Abdulmajeed; Beck, Frances W J; Bao, Bin; Wang, Zhiwei; Banerjee, Sanjeev; Sarkar, Fazlul H; Mohammad, Ramzi M; Hadi, Sheikh M; Azmi, Asfar S

2012-04-01

Many critical factors such as hypoxia, nutrient deficiency, activation of glycolytic pathway/Warburg effect contribute to the observed low pH in tumors compared to normal tissue. Studies suggest that such tumor specific acidic environment can be exploited for the development of therapeutic strategies against cancer. Independent observations show reduction in pH of mammalian cells undergoing internucleosomal DNA fragmentation and apoptosis. As such, our group has extensively demonstrated that anticancer mechanisms of different plant polyphenols involve mobilization of endogenous copper and consequent internucleosomal DNA breakage. Copper is redox active metal, an essential component of chromatin and is sensitive to subtle pH changes in its microenvironment. Here we explored whether, acidic pH promotes growth inhibition, apoptosis, and DNA damaging capacity of chemopreventive agent resveratrol. Our results reveal that growth inhibition and internucleosomal DNA fragmentation induced apoptosis in Capan-2 and Panc-28 pancreatic cancer cell lines (and not in normal HPDE cells) by resveratrol is enhanced at lower pH. Using comet assay, we further demonstrate that DNA breakage by resveratrol is enhanced with acidification. Membrane permeable copper specific chelator neocuproine (and not iron chelator orthophenanthroline) abrogated growth inhibition and apoptosis by resveratrol. Western blot results show enhanced activation of DNA laddering marker H2.aX by resveratrol at acidic pH that was reversed by neocuproine and not by orthophenanthroline. Our findings provide irrevocable proof that low pH environment can be turned into tumor weakness and assist in eradication of cancer cells by resveratrol. Copyright © 2011 Wiley Periodicals, Inc.

Six Month In Situ High-Resolution Carbonate Chemistry and Temperature Study on a Coral Reef Flat Reveals Asynchronous pH and Temperature Anomalies.

Directory of Open Access Journals (Sweden)

David I Kline

Full Text Available Understanding the temporal dynamics of present thermal and pH exposure on coral reefs is crucial for elucidating reef response to future global change. Diel ranges in temperature and carbonate chemistry parameters coupled with seasonal changes in the mean conditions define periods during the year when a reef habitat is exposed to anomalous thermal and/or pH exposure. Anomalous conditions are defined as values that exceed an empirically estimated threshold for each variable. We present a 200-day time series from June through December 2010 of carbonate chemistry and environmental parameters measured on the Heron Island reef flat. These data reveal that aragonite saturation state, pH, and pCO2 were primarily modulated by biologically-driven changes in dissolved organic carbon (DIC and total alkalinity (TA, rather than salinity and temperature. The largest diel temperature ranges occurred in austral spring, in October (1.5 - 6.6°C and lowest diel ranges (0.9 - 3.2°C were observed in July, at the peak of winter. We observed large diel total pH variability, with a maximum range of 7.7 - 8.5 total pH units, with minimum diel average pH values occurring during spring and maximum during fall. As with many other reefs, the nighttime pH minima on the reef flat were far lower than pH values predicted for the open ocean by 2100. DIC and TA both increased from June (end of Fall to December (end of Spring. Using this high-resolution dataset, we developed exposure metrics of pH and temperature individually for intensity, duration, and severity of low pH and high temperature events, as well as a combined metric. Periods of anomalous temperature and pH exposure were asynchronous on the Heron Island reef flat, which underlines the importance of understanding the dynamics of co-occurrence of multiple stressors on coastal ecosystems.

Six Month In Situ High-Resolution Carbonate Chemistry and Temperature Study on a Coral Reef Flat Reveals Asynchronous pH and Temperature Anomalies.

Science.gov (United States)

Kline, David I; Teneva, Lida; Hauri, Claudine; Schneider, Kenneth; Miard, Thomas; Chai, Aaron; Marker, Malcolm; Dunbar, Rob; Caldeira, Ken; Lazar, Boaz; Rivlin, Tanya; Mitchell, Brian Gregory; Dove, Sophie; Hoegh-Guldberg, Ove

2015-01-01

Understanding the temporal dynamics of present thermal and pH exposure on coral reefs is crucial for elucidating reef response to future global change. Diel ranges in temperature and carbonate chemistry parameters coupled with seasonal changes in the mean conditions define periods during the year when a reef habitat is exposed to anomalous thermal and/or pH exposure. Anomalous conditions are defined as values that exceed an empirically estimated threshold for each variable. We present a 200-day time series from June through December 2010 of carbonate chemistry and environmental parameters measured on the Heron Island reef flat. These data reveal that aragonite saturation state, pH, and pCO2 were primarily modulated by biologically-driven changes in dissolved organic carbon (DIC) and total alkalinity (TA), rather than salinity and temperature. The largest diel temperature ranges occurred in austral spring, in October (1.5 - 6.6°C) and lowest diel ranges (0.9 - 3.2°C) were observed in July, at the peak of winter. We observed large diel total pH variability, with a maximum range of 7.7 - 8.5 total pH units, with minimum diel average pH values occurring during spring and maximum during fall. As with many other reefs, the nighttime pH minima on the reef flat were far lower than pH values predicted for the open ocean by 2100. DIC and TA both increased from June (end of Fall) to December (end of Spring). Using this high-resolution dataset, we developed exposure metrics of pH and temperature individually for intensity, duration, and severity of low pH and high temperature events, as well as a combined metric. Periods of anomalous temperature and pH exposure were asynchronous on the Heron Island reef flat, which underlines the importance of understanding the dynamics of co-occurrence of multiple stressors on coastal ecosystems.

Effect of pH on saturated hydraulic conductivity and soil dispersion

Energy Technology Data Exchange (ETDEWEB)

Suarez, D.L.; Roades, J.D.; Lavado, R.; Grieve, C.M.

The adverse effects of exchangeable sodium on soil hydraulic conductivity (K) are well known, but at present only sodicity and total electrolyte concentration are used in evaluating irrigation water suitability. In arid areas, high sodicity is often associatd with high dissolved carbonate and thus high pH, but in humid areas high sodicity may be associated with low pH. To evaluate the effect of pH (as an independent variable) on K, solutions with the same SAR and electrolyte level were prepared at pH 6, 7, 8, and 9. Saturated K values were determined at constant flux in columns packed at a bulk density of 1.5 Mg m/sup -3/. At pH 9, saturated K values were lower than at pH 6 for a montmorillonitic and kaolinitic soil. For a vermiculitic soil with lower organic carbon and higher silt content, pH changes did not cause large K differences. Decreases in K were not reversible on application of waters with higher electrolyte levels. The results from the K experiments were generally consistent with optical transmission measurements of dispersion. Although anion adsorption was at or below detection limits and cation exchange capacity (CEC) was only slightly dependent on pH, differences in pH effects on K among soils are likely due to differences in quantities of variable-charge minerals and organic matter.

High-Resolution Denitrification Kinetics in Pasture Soils Link N2O Emissions to pH, and Denitrification to C Mineralization.

Directory of Open Access Journals (Sweden)

Md Sainur Samad

Full Text Available Denitrification in pasture soils is mediated by microbial and physicochemical processes leading to nitrogen loss through the emission of N2O and N2. It is known that N2O reduction to N2 is impaired by low soil pH yet controversy remains as inconsistent use of soil pH measurement methods by researchers, and differences in analytical methods between studies, undermine direct comparison of results. In addition, the link between denitrification and N2O emissions in response to carbon (C mineralization and pH in different pasture soils is still not well described. We hypothesized that potential denitrification rate and aerobic respiration rate would be positively associated with soils. This relationship was predicted to be more robust when a high resolution analysis is performed as opposed to a single time point comparison. We tested this by characterizing 13 different temperate pasture soils from northern and southern hemispheres sites (Ireland and New Zealand using a fully automated-high-resolution GC detection system that allowed us to detect a wide range of gas emissions simultaneously. We also compared the impact of using different extractants for determining pH on our conclusions. In all pH measurements, soil pH was strongly and negatively associated with both N2O production index (IN2O and N2O/(N2O+N2 product ratio. Furthermore, emission kinetics across all soils revealed that the denitrification rates under anoxic conditions (NO+N2O+N2 μmol N/h/vial were significantly associated with C mineralization (CO2 μmol/h/vial measured both under oxic (r2 = 0.62, p = 0.0015 and anoxic (r2 = 0.89, p<0.0001 conditions.

Resistance of Streptococcus bovis to acetic acid at low pH: Relationship between intracellular pH and anion accumulation

Energy Technology Data Exchange (ETDEWEB)

Russell, J.B. (Cornell Univ., Ithaca, NY (USA))

1991-01-01

Streptococcus bovis JB1, an acid-tolerant ruminal bacterium, was able to grown at pHs from 6.7 to 4.5, and 100 mM acetate had little effect on growth rate or proton motive force across the cell membrane. When S. bovis was grown in glucose-limited chemostats at pH 5.2, the addition of sodium acetate (as much as 100 mM) had little effect on the production of bacterial protein. At higher concentrations of sodium acetate (100 to 360 mM), production of bacterial protein declined, but this decrease could largely be explained by a shift in fermentation products (acetate, formate, and ethanol production to lactate production) and a decline in ATP production (3 ATP per glucose versus 2 ATP per glucose). Y{sub ATP} (grams of cells per mole at ATP) was not decreased significantly even by high concentrations of acetate. Cultures supplemented with 100 mM sodium acetate took up ({sup 14}C)acetate and ({sup 14}C)benzoate in accordance with the Henderson-Hasselbalch equation and gave similar estimates of intracellular pH. As the extracellular pH declined, S. bovis allowed its intracellular pH to decrease and maintained a relatively constant pH gradient across the cell membrane (0.9 unit). The decrease in intracellular pH prevented S. bovis from accumulating large amounts of acetate anion. On the basis of these results it did not appear that acetate was acting as an uncoupler. The sensitivity of other bacteria to volatile fatty acids at low pH is explained most easily by a high transmembrane pH gradient and anion accumulation.

Resistance of Streptococcus bovis to acetic acid at low pH: Relationship between intracellular pH and anion accumulation

International Nuclear Information System (INIS)

Russell, J.B.

1991-01-01

Streptococcus bovis JB1, an acid-tolerant ruminal bacterium, was able to grown at pHs from 6.7 to 4.5, and 100 mM acetate had little effect on growth rate or proton motive force across the cell membrane. When S. bovis was grown in glucose-limited chemostats at pH 5.2, the addition of sodium acetate (as much as 100 mM) had little effect on the production of bacterial protein. At higher concentrations of sodium acetate (100 to 360 mM), production of bacterial protein declined, but this decrease could largely be explained by a shift in fermentation products (acetate, formate, and ethanol production to lactate production) and a decline in ATP production (3 ATP per glucose versus 2 ATP per glucose). Y ATP (grams of cells per mole at ATP) was not decreased significantly even by high concentrations of acetate. Cultures supplemented with 100 mM sodium acetate took up [ 14 C]acetate and [ 14 C]benzoate in accordance with the Henderson-Hasselbalch equation and gave similar estimates of intracellular pH. As the extracellular pH declined, S. bovis allowed its intracellular pH to decrease and maintained a relatively constant pH gradient across the cell membrane (0.9 unit). The decrease in intracellular pH prevented S. bovis from accumulating large amounts of acetate anion. On the basis of these results it did not appear that acetate was acting as an uncoupler. The sensitivity of other bacteria to volatile fatty acids at low pH is explained most easily by a high transmembrane pH gradient and anion accumulation

Effects of high voltage electrical stimulation on the rate of pH decline, meat quality and color stability in chilled beef carcasses

OpenAIRE

Mombeni, Ehsan Gharib; Mombeini, Manoochehr Gharib; Figueiredo, Lucas Chaves; Siqueira, Luciano Soares Jacintho; Dias, Debora Testoni

2013-01-01

Objective: To determine the effects of high voltage electrical stimulation (HVES, 800 Voltage) on rapid decreases in pH values and improvements in meat quality. Methods: A total of 50 beef carcasses were applied, divided into two groups, one as a control and another for HVES. Meat quality was evaluated based on M. longissimus dorsi by examining pH and temperature levels at 1, 2, 5, 10 and 24 h, while color stability was examined seven days after slaughter. Results: HVES decreased the pH...

The importance of ammonium mobility in nitrogen-impacted unfertilized grasslands: A critical reassessment

International Nuclear Information System (INIS)

Mian, Ishaq Ahmad; Riaz, Muhammad; Cresser, Malcolm S.

2009-01-01

The physico-chemical absorption characteristics of ammonium-N for 10 soils from 5 profiles in York, UK, show its high potential mobility in N deposition-impacted, unfertilized, permanent grassland soils. Substantial proportions of ammonium-N inputs were retained in the solution phase, indicating that ammonium translocation plays an important role in the N cycling in, and losses from, such soils. This conclusion was further supported by measuring the ammonium-N leaching from intact plant/soil microcosms. The ammonium-N absorption characteristics apparently varied with soil pH, depth and soil texture. It was concluded for the most acid soils especially that ammonium-N leached from litter horizons could be seriously limiting the capacity of underlying soils to retain ammonium. Contrary to common opinion, more attention therefore needs to be paid to ammonium leaching and its potential role in biogeochemical N cycling in semi-natural soil systems subject to atmospheric pollution. - Ammonium mobility is more important than previously thought in N-impacted, unfertilized grasslands

The PhD by Publication

Directory of Open Access Journals (Sweden)

Susi Peacock

2017-07-01

Full Text Available Aim/Purpose: The purpose of this work is to develop more nuanced understandings of the PhD by publication, particularly raising awareness of the retrospective PhD by publication. The article aims to contribute to contemporary debates about the differing pathways to the attainment of doctoral study completion and the artifacts submitted for that purpose. It also seeks to support prospective graduate students and supervisors who are embarking upon alternative routes to doctoral accreditation. Background: The PhD is considered the pinnacle of academic study – highly cherished, and replete with deeply held beliefs. In response to changes in job markets, developments in the disciplines, and more varied student cohorts, diverse pathways to completion of this award have emerged, such as the PhD by publication (PhDP. A PhDP may either be prospective or retrospective. For the former, publications are planned and created with their contributions to the PhDP in mind. The retrospective PhD is assembled after some, or most, of the publications have been completed. The artifact submitted for examination in this case consists of a series of peer-reviewed academic papers, books, chapters, or equivalents that have been published or accepted for publication, accompanied by an over-arching narrative. The retrospective route is particularly attractive for professionals who are research-active but lack formal academic accreditation at the highest level. Methodology: This article calls upon a literature review pertaining to the award of PhDP combined with the work of authors who offer their personal experiences of the award. The author also refers to her candidature as a Scottish doctoral student whilst studying for the award of PhD by publication. Contribution: This work raises awareness of the PhDP as a credible and comparable pathway for graduate students. The article focuses upon the retrospective PhDP which, as with all routes to doctoral accreditation, has

Transformational Electronics: Towards Flexible Low-Cost High Mobility Channel Materials

KAUST Repository

Nassar, Joanna M.

2014-05-01

For the last four decades, Si CMOS technology has been advancing with Moore’s law prediction, working itself down to the sub-20 nm regime. However, fundamental problems and limitations arise with the down-scaling of transistors and thus new innovations needed to be discovered in order to further improve device performance without compromising power consumption and size. Thus, a lot of studies have focused on the development of new CMOS compatible architectures as well as the discovery of new high mobility channel materials that will allow further miniaturization of CMOS transistors and improvement of device performance. Pushing the limits even further, flexible and foldable electronics seem to be the new attractive topic. By being able to make our devices flexible through a CMOS compatible process, one will be able to integrate hundreds of billions of more transistors in a small volumetric space, allowing to increase the performance and speed of our electronics all together with making things thinner, lighter, smaller and even interactive with the human skin. Thus, in this thesis, we introduce for the first time a cost-effective CMOS compatible approach to make high-k/metal gate devices on flexible Germanium (Ge) and Silicon-Germanium (SiGe) platforms. In the first part, we will look at the various approaches in the literature that has been developed to get flexible platforms, as well as we will give a brief overview about epitaxial growth of Si1-xGex films. We will also examine the electrical properties of the Si1-xGex alloys up to Ge (x=1) and discuss how strain affects the band structure diagram, and thus the mobility of the material. We will also review the material growth properties as well as the state-of-the-art results on high mobility metal-oxide semiconductor capacitors (MOSCAPs) using strained SiGe films. Then, we will introduce the flexible process that we have developed, based on a cost-effective “trench-protect-release-reuse” approach, utilizing

Millimeter Wave Hybrid Photonic Wireless Links for High-Speed Wireless Access and Mobile Fronthaul

DEFF Research Database (Denmark)

Rommel, Simon

As the introduction of the fifth generation of mobile services (5G) is set to revolutionize the way people, devices and machines connect, the changes to the underlying networks and technologies are no less drastic. The massive increase in user and data capacity, as well as the decrease in latency...... networks. In summary, the work presented in this thesis has regarded a multitude of aspects of millimeter wave hybrid photonic wireless links, expanding upon the state of the art and showing their feasibility for use in fifth generation mobile and high speed wireless access networks – hopefully bringing...

Control of residual carbon concentration in GaN high electron mobility transistor and realization of high-resistance GaN grown by metal-organic chemical vapor deposition

Energy Technology Data Exchange (ETDEWEB)

He, X.G. [State Key Laboratory on Integrated Optoelectronics, Institute of Semiconductors, Chinese Academy of Sciences, P.O. Box 912, Beijing 100083 (China); Zhao, D.G., E-mail: dgzhao@red.semi.ac.cn [State Key Laboratory on Integrated Optoelectronics, Institute of Semiconductors, Chinese Academy of Sciences, P.O. Box 912, Beijing 100083 (China); Jiang, D.S.; Liu, Z.S.; Chen, P.; Le, L.C.; Yang, J.; Li, X.J. [State Key Laboratory on Integrated Optoelectronics, Institute of Semiconductors, Chinese Academy of Sciences, P.O. Box 912, Beijing 100083 (China); Zhang, S.M.; Zhu, J.J.; Wang, H.; Yang, H. [Suzhou Institute of Nano-tech and Nano-bionics, Chinese Academy of Sciences, Suzhou 215125 (China)

2014-08-01

GaN films were grown by metal-organic chemical vapor deposition (MOCVD) under various growth conditions. The influences of MOCVD growth parameters, i.e., growth pressure, ammonia (NH{sub 3}) flux, growth temperature, trimethyl-gallium flux and H{sub 2} flux, on residual carbon concentration ([C]) were systematically investigated. Secondary ion mass spectroscopy measurements show that [C] can be effectively modulated by growth conditions. Especially, it can increase by reducing growth pressure up to two orders of magnitude. High-resistance (HR) GaN epilayer with a resistivity over 1.0 × 10{sup 9} Ω·cm is achieved by reducing growth pressure. The mechanism of the formation of HR GaN epilayer is discussed. An Al{sub x}Ga{sub 1−x}N/GaN high electron mobility transistor structure with a HR GaN buffer layer and an additional low-carbon GaN channel layer is presented, exhibiting a high two dimensional electron gas mobility of 1815 cm{sup 2}/Vs. - Highlights: • Influence of MOCVD parameters on residual carbon concentration in GaN is studied. • GaN layer with a resistivity over 1 × 10{sup 9} Ω·cm is achieved by reducing growth pressure. • High electron mobility transistor (HEMT) structures were prepared. • Control of residual carbon content results in HEMT with high 2-D electron gas mobility.

Phosphorene: an unexplored 2D semiconductor with a high hole mobility.

Science.gov (United States)

Liu, Han; Neal, Adam T; Zhu, Zhen; Luo, Zhe; Xu, Xianfan; Tománek, David; Ye, Peide D

2014-04-22

We introduce the 2D counterpart of layered black phosphorus, which we call phosphorene, as an unexplored p-type semiconducting material. Same as graphene and MoS2, single-layer phosphorene is flexible and can be mechanically exfoliated. We find phosphorene to be stable and, unlike graphene, to have an inherent, direct, and appreciable band gap. Our ab initio calculations indicate that the band gap is direct, depends on the number of layers and the in-layer strain, and is significantly larger than the bulk value of 0.31-0.36 eV. The observed photoluminescence peak of single-layer phosphorene in the visible optical range confirms that the band gap is larger than that of the bulk system. Our transport studies indicate a hole mobility that reflects the structural anisotropy of phosphorene and complements n-type MoS2. At room temperature, our few-layer phosphorene field-effect transistors with 1.0 μm channel length display a high on-current of 194 mA/mm, a high hole field-effect mobility of 286 cm(2)/V·s, and an on/off ratio of up to 10(4). We demonstrate the possibility of phosphorene integration by constructing a 2D CMOS inverter consisting of phosphorene PMOS and MoS2 NMOS transistors.

A fluorescent probe which allows highly specific thiol labeling at low pH

DEFF Research Database (Denmark)

Nielsen, Jonas W.; Jensen, Kristine Steen; Hansen, Rosa E.

2012-01-01

and properties of a thiol-specific reagent, fluorescent cyclic activated disulfide (FCAD), which includes the fluorescein moiety as fluorophore and utilizes a variation of thiol-disulfide exchange chemistry. The leaving-group character of FCAD makes it reactive at pH 3, allowing modification at low pH, limiting...

Double pulse doped InGaAs/AlGaAs/GaAs pseudomorphic high-electron-mobility transistor heterostructures

International Nuclear Information System (INIS)

Egorov, A. Yu.; Gladyshev, A. G.; Nikitina, E. V.; Denisov, D. V.; Polyakov, N. K.; Pirogov, E. V.; Gorbazevich, A. A.

2010-01-01

Double pulse doped (δ-doped) InGaAs/AlGaAs/GaAs pseudomorphic high-electron-mobility transistor (HEMT) heterostructures were grown by molecular-beam epitaxy using a multiwafer technological system. The room-temperature electron mobility was determined by the Hall method as 6550 and 6000 cm 2 /(V s) at sheet electron densities of 3.00 x 10 12 and 3.36 x 10 12 cm -2 , respectively. HEMT heterostructures fabricated in a single process feature high uniformity of structural and electrical characteristics over the entire area of wafers 76.2 mm in diameter and high reproducibility of characteristics from process to process.

Theoretical prediction of high electron mobility in multilayer MoS2 heterostructured with MoSe2

Science.gov (United States)

Ji, Liping; Shi, Juan; Zhang, Z. Y.; Wang, Jun; Zhang, Jiachi; Tao, Chunlan; Cao, Haining

2018-01-01

Two-dimensional (2D) MoS2 has been considered to be one of the most promising semiconducting materials with the potential to be used in novel nanoelectronic devices. High carrier mobility in the semiconductor is necessary to guarantee a low power dissipation and a high switch speed of the corresponding electronic device. Strain engineering in 2D materials acts as an important approach to tailor and design their electronic and carrier transport properties. In this work, strain is introduced to MoS2 through perpendicularly building van der Waals heterostructures MoSe2-MoS2. Our first-principles calculations demonstrate that acoustic-phonon-limited electron mobility can be significantly enhanced in the heterostructures compared with that in pure multilayer MoS2. It is found that the effective electron mass and the deformation potential constant are relatively smaller in the heterostructures, which is responsible for the enhancement in the electron mobility. Overall, the electron mobility in the heterostructures is about 1.5 times or more of that in pure multilayer MoS2 with the same number of layers for the studied structures. These results indicate that MoSe2 is an excellent material to be heterostructured with multilayer MoS2 to improve the charge transport property.

Direct observation and determination of the mechanisms governing mobility of asbestos in porous media

Science.gov (United States)

Seiphoori, A.; Ortiz, C. P.; Jerolmack, D. J.

2017-12-01

Transport of asbestos through soil by groundwater is typically considered to be negligible. There are indications, however, that under some conditions of pore-water/soil chemistry asbestos may become mobile, implying that buried contaminants could migrate from a disposal site and surface elsewhere. Shape, size and surface charge may influence the physical and chemical interactions of colloids with the soil matrix, and asbestos consists of elongated particles with different size and unique surface charge properties. Although chemical factors such as pH and ionic strength of pore water may affect the transport properties, the presence of dissolved organic carbon (DOC) has been identified to remarkably enhance the mobility of colloids including asbestos. To date, there is no explanation for how the presence of DOC may facilitate the mobilization of asbestos in soil - mainly because the soil medium has been treated as a black box without the possibility of observing particles within the matrix. Here, we investigated the mobility of chrysotile asbestos particles ( 10 um long) in porous media by developing a flow cell with an optically-transparent porous medium composed of granules of a refractive-index matched material. This enabled us to observe and track the particles within the water-saturated porous medium using in situ microscopy. The aqueous suspension of asbestos fibers was passed through this artificial soil, while the physical and chemical interaction of asbestos particles with the medium and their pore-scale distribution were analyzed. We studied the effects of changing solution chemistry (e.g., ionic strength, pH, and DOC content) on transport, attachment and aggregation of chrysotile particles. Experiments revealed a novel mechanism where the DOC-associated nanoparticles attach to chrysotile fibers by an electrostatic attraction, which facilitates their mobilization through the porous medium while modulating aggregation among fibers. Although pH and ionic

Accurate on-chip measurement of the Seebeck coefficient of high mobility small molecule organic semiconductors

Directory of Open Access Journals (Sweden)

C. N. Warwick

2015-09-01

Full Text Available We present measurements of the Seebeck coefficient in two high mobility organic small molecules, 2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene (C8-BTBT and 2,9-didecyl-dinaphtho[2,3-b:2′,3′-f]thieno[3,2-b]thiophene (C10-DNTT. The measurements are performed in a field effect transistor structure with high field effect mobilities of approximately 3 cm2/V s. This allows us to observe both the charge concentration and temperature dependence of the Seebeck coefficient. We find a strong logarithmic dependence upon charge concentration and a temperature dependence within the measurement uncertainty. Despite performing the measurements on highly polycrystalline evaporated films, we see an agreement in the Seebeck coefficient with modelled values from Shi et al. [Chem. Mater. 26, 2669 (2014] at high charge concentrations. We attribute deviations from the model at lower charge concentrations to charge trapping.

MobileFaceNets: Efficient CNNs for Accurate Real-time Face Verification on Mobile Devices

OpenAIRE

Chen, Sheng; Liu, Yang; Gao, Xiang; Han, Zhen

2018-01-01

In this paper, we proposed a class of extremely efficient CNN models, MobileFaceNets, which use less than 1 million parameters and are specifically tailored for high-accuracy real-time face verification on mobile and embedded devices. We first make a simple analysis on the weakness of common mobile networks for face verification. The weakness has been well overcome by our specifically designed MobileFaceNets. Under the same experimental conditions, our MobileFaceNets achieve significantly sup...

Mobile School Service

Directory of Open Access Journals (Sweden)

Borislav Odadzic

2010-04-01

Full Text Available What is in common for the majority of young people? Mobile phone. In epoch of rapid development of information technologies the time came in which only few people do not have mobiles, especially among young people in high schools. Researches which we made in our school say that this percentage (rate is really high 99,23% at this moment. The educational institutions should use this opportunity. In aim to improve the success of students the mobile service is developed, which will be described in this work. This is first result which provides a cognitive tool which is supporting the independent learning by applying mobile phones with wireless communication technology to extend learning outside of the classroom in Serbia. The service was developed during times when we didn’t know anything about how much and in which way m-learning was being used in the world.

Integrating mHealth Mobile Applications to Reduce High Risk Drinking among Underage Students

Science.gov (United States)

Kazemi, Donna M.; Cochran, Allyson R.; Kelly, John F.; Cornelius, Judith B.; Belk, Catherine

2014-01-01

Objective: College students embrace mobile cell phones (MCPs) as a primary communication and entertainment device. The aim of this study was to investigate college students' perceptions toward using mHealth technology to deliver interventions to prevent high-risk drinking and associated consequences. Design/setting: Four focus group interviews…

High-Speed Mobile Communications in Hostile Environments

CERN Document Server

AUTHOR|(SzGeCERN)739920; Sierra, Rodrigo; Chapron, Frederic; CERN. Geneva. IT Department

2015-01-01

With the inexorable increase in the use of mobile devices, wireless connectivity is expected by users anywhere, anytime. In general, this requirement is addressed in office buildings or public locations through the use of Wi-Fi technology but Wi-Fi is not well adapted for use in large experiment halls and complex underground environments, especially those where radiation exposure is an issue, such as the LHC tunnel and experimental caverns. 4G/LTE technology, however, looks to be well adapted to addressing mobility needs in such areas. We report here the studies CERN has undertaken on the use of 4G/LTE in the LHC tunnel, presenting results on the data throughput that can be achieved and discussing issues such as the provision of a consistent user experience.

Achieving high field-effect mobility in amorphous indium-gallium-zinc oxide by capping a strong reduction layer.

Science.gov (United States)

Zan, Hsiao-Wen; Yeh, Chun-Cheng; Meng, Hsin-Fei; Tsai, Chuang-Chuang; Chen, Liang-Hao

2012-07-10

An effective approach to reduce defects and increase electron mobility in a-IGZO thin-film transistors (a-IGZO TFTs) is introduced. A strong reduction layer, calcium, is capped onto the back interface of a-IGZO TFT. After calcium capping, the effective electron mobility of a-IGZO TFT increases from 12 cm(2) V(-1) s(-1) to 160 cm(2) V(-1) s(-1). This high mobility is a new record, which implies that the proposed defect reduction effect is key to improve electron transport in oxide semiconductor materials. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Analysis of Proton Radiation Effects on Gallium Nitride High Electron Mobility Transistors

Science.gov (United States)

2017-03-01

non - ionizing proton radiation damage effects at different energy levels on a GaN-on-silicon high electron mobility transistor...DISTRIBUTION CODE 13. ABSTRACT (maximum 200 words) In this work, a physics-based simulation of non - ionizing proton radiation damage effects at different...Polarization . . . . . . . . . . . . . . 6 2.3 Non - Ionizing Radiation Damage Effects . . . . . . . . . . . . . . . 10 2.4 Non - Ionizing Radiation Damage in

Validation of a triangular quantum well model for GaN-based HEMTs used in pH and dipole moment sensing

International Nuclear Information System (INIS)

Rabbaa, S; Stiens, J

2012-01-01

Gallium nitride (GaN) is a relatively new semiconductor material that has the potential of replacing gallium arsenide (GaAs) in some of the more recent technological applications, for example chemical sensor applications. In this paper, we introduce a triangular quantum well model for an undoped AlGaN/GaN high electron mobility transistor (HEMT) structure used as a chemical and biological sensor for pH and dipole moment measurements of polar liquids. We have performed theoretical calculations related to the HEMT characteristics and we have compared them with experimental measurements carried out in many previous papers. These calculations include the current-voltage (I-V) characteristics of the device, the surface potential, the change in the drain current with the dipole moment and the drain current as a function of pH. The results exhibit good agreement with experimental measurements for different polar liquids and electrolyte solutions. It is also found that the drain current of the device exhibits a large linear variation with the dipole moment, and that the surface potential and the drain current depend strongly on the pH. Therefore, it can distinguish molecules with slightly different dipole moments and solutions with small variations in pH. The ability of the device to sense biomolecules (such as proteins) with very large dipole moments is investigated.

Detection of irradiated peppers by viscosity measurement at extremely high pH

International Nuclear Information System (INIS)

Hayashi, Toru; Todoriki, Setsuko

1996-01-01

The viscosities of aqueous suspensions of irradiated peppers determined after heat gelatinization were influenced by the pH of the suspension to a greater degree than those of unirradiated ones. Viscosity measurement under an extremely alkaline condition (pH 13.8) resulted in a significant different between irradiated peppers and unirradiated ones, irrespective of the planting locality and storage period. All of the pepper samples irradiated at 5 kGy showed viscosity values significantly lower than unirradiated ones. (Author)

Advantages of low pH and limited oxygenation in arsenite removal from water by zero-valent iron.

Science.gov (United States)

Klas, Sivan; Kirk, Donald W

2013-05-15

The removal of toxic arsenic species from contaminated waters by zero-valent iron (ZVI) has drawn considerable attention in recent years. In this approach, arsenic ions are mainly removed by adsorption to the iron corrosion products. Reduction to zero-valent arsenic on the ZVI surface is possible in the absence of competing oxidants and can reduce arsenic mobility and sludge formation. However, associated removal rates are relatively low. In the current study, simultaneous high reduction and removal rates of arsenite (H3AsO3), the more toxic and mobile environmentally occurring arsenic species, was demonstrated by reacting it with ZVI under limited aeration and relatively low pH. 90% of the removed arsenic was attached to the ZVI particles and 60% of which was in the elemental state. Under the same non-acidic conditions, only 40-60% of the removed arsenic was attached to the ZVI with no change in arsenic oxidation state. Under anaerobic conditions, reduction occurred but total arsenic removal rate was significantly lower and ZVI demand was higher. The effective arsenite removal under acidic oxygen-limited conditions was explained by formation of Fe(II)-solid intermediate on the ZVI surface that provided high surface area and reducing power. Copyright © 2013 Elsevier B.V. All rights reserved.

Changing noise levels in a high CO2/lower pH ocean

Science.gov (United States)

Brewer, P. G.; Hester, K. C.; Peltzer, E. T.; Kirkwood, W. J.

2008-12-01

We show that ocean acidification from fossil fuel CO2 invasion and from increased respiration/reduced ventilation, has significantly reduced ocean sound absorption and thus increased ocean noise levels in the kHz frequency range. Below 10 kHz, sound absorption occurs due to well known chemical relaxations in the B(OH)3/B(OH)4- and HCO3-/CO32- systems. The pH dependence of these chemical relaxations results in decreased sound absorption (α = dB/km) as the ocean becomes more acidic from increased CO2 levels. The scale of surface ocean pH change today from the +105 ppmv change in atmospheric CO2 is about - 0.12 pH, resulting in frequency dependent decreases in sound absorption that now exceed 12% over pre- industrial. Under reasonable projections of future fossil fuel CO2 emissions and other sources a pH change of 0.3 units or more can be anticipated by mid-century, resulting in a decrease in α by almost 40%. Increases in water temperature have a smaller effect but also contribute to decreased sound absorption. Combining a lowering of 0.3 pH units with an increase of 3°C, α will decrease further to almost 45%. Ambient noise levels in the ocean within the auditory range critical for environmental, military, and economic interests are set to increase significantly due to the combined effects of decreased absorption and increasing sources from mankind's activities. Incorporation of sound absorption in modeling future ocean scenarios (R. Zeebe, personal communication) and long-term monitoring possibly with the aid of modern cabled observatories can give insights in how ocean noise will continue to change and its effect on groups such as marine mammals which communicate in the affected frequency range.

Electron drift time in silicon drift detectors: A technique for high precision measurement of electron drift mobility

International Nuclear Information System (INIS)

Castoldi, A.; Rehak, P.

1995-01-01

This paper presents a precise absolute measurement of the drift velocity and mobility of electrons in high resistivity silicon at room temperature. The electron velocity is obtained from the differential measurement of the drift time of an electron cloud in a silicon drift detector. The main features of the transport scheme of this class of detectors are: the high uniformity of the electron motion, the transport of the signal electrons entirely contained in the high-purity bulk, the low noise timing due to the very small anode capacitance (typical value 100 fF), and the possibility to measure different drift distances, up to the wafer diameter, in the same semiconductor sample. These features make the silicon drift detector an optimal device for high precision measurements of carrier drift properties. The electron drift velocity and mobility in a 10 kΩ cm NTD n-type silicon wafer have been measured as a function of the electric field in the range of possible operation of a typical drift detector (167--633 V/cm). The electron ohmic mobility is found to be 1394 cm 2 /V s. The measurement precision is better than 1%. copyright 1995 American Institute of Physics

Effect of pH and chloride on the micro-mechanism of pitting corrosion for high strength pipeline steel in aerated NaCl solutions

International Nuclear Information System (INIS)

Wang, Yafei; Cheng, Guangxu; Wu, Wei; Qiao, Qiao; Li, Yun; Li, Xiufeng

2015-01-01

Highlights: • Pitting behavior of X80 steel in aerated NaCl solutions is studied systematically. • Unique large pit morphology is observed in neutral/acidic NaCl solutions. • In low pH solutions, pit will propagate in the horizontal direction, leading to the shallow shape of pitting morphology; in high pH solutions, the pit sizes are much smaller. • Film growth, which is dependent on the pH and chloride concentration, has great influence on the cathodic reaction by affecting oxygen diffusion process. - Abstract: The pitting corrosion mechanism of high strength pipeline steel in aerated NaCl solutions with different pH and chloride content was investigated, using potentiodynamic polarization, electrochemical impedance spectroscopy (EIS) and scanning electron microscope (SEM). The pitting behavior in alkaline solutions was found to be significantly different from that in neutral and acidic solutions. Electrochemical results and SEM images indicate that the product film formed on the steel surface results in different corrosion behavior in an alkaline solution. SEM images show that pH and chloride concentration in the bulk solution have a great influence on the pitting morphology. Unique large pit morphology due to corrosion in neutral/acidic solutions with 0.05 mol/L NaCl was observed. The relationship between solution pH and the effect of chloride concentration is also discussed

Investigation of high mobility pseudomorphic SiGe p-channels in Si MOSFETS at low and high electric fields

International Nuclear Information System (INIS)

Palmer, Martin John

2001-01-01

Silicon Metal-Oxide-Semiconductor Field Effect Transistors (MOSFETs) for high speed, high current applications are rapidly approaching the physical and financial limits of the technology. This opens opportunities for the incorporation of materials with intrinsically better transport characteristics. An alloy of silicon and germanium is one such material that is gaining much recognition as the active component of MOSFETs and as the secondary structures (such as the gate electrode). This work examines a batch of buried channel Si 0.64 Ge 0.36 p-MOSFETs, with a minimum effective length of 0.35 μm, under different bias conditions and at different temperatures. High current and transconductance enhancements are apparent at long gate lengths. The carrier mobility is up to a factor of 2.5 times that of silicon at room temperature and 7.5 times at 4 K. A clear trend of decreasing peak mobility with decreasing silicon cap thickness is evident. Simulations show that scattering caused by the roughness of the SiO 2 /Si interface dominates, rather than alloy scattering or Si/SiGe roughness, even for a buried channel. This scattering increases with the proximity of the carriers to the interface. An increase of interface trap density with decreasing cap thickness, demonstrates that segregated germanium exists some distance into the cap and interferes with the oxidation process. This will increase scattering through increased SiO 2 /Si roughness and increased trapped charge. The short channel, high field results are comparable or slightly worse than those of silicon due to lower saturation drift velocity. However, fitting to a drift-diffusion model shows an apparent increase in saturation velocity for short channels, especially at low temperatures. This effect correlates with the low field mobility and is greater for devices containing SiGe. This is an indication of velocity overshoot, which may enhance the performance of SiGe MOSFETs at deep submicron gate lengths. (author)

Double-pass Mach-Zehnder fiber interferometer pH sensor.

Science.gov (United States)

Tou, Zhi Qiang; Chan, Chi Chiu; Hong, Jesmond; Png, Shermaine; Eddie, Khay Ming Tan; Tan, Terence Aik Huang

2014-04-01

A biocompatible fiber-optic pH sensor based on a unique double-pass Mach-Zehnder interferometer is proposed. pH responsive poly(2-hydroxyethyl methacrylate-co-2-(dimethylamino)ethyl methacrylate) hydrogel coating on the fiber swells/deswells in response to local pH, leading to refractive index changes that manifest as shifting of interference dips in the optical spectrum. The pH sensor is tested in spiked phosphate buffer saline and demonstrates high sensitivity of 1.71  nm/pH, pH 0.004 limit of detection with good responsiveness, repeatability, and stability. The proposed sensor has been successfully applied in monitoring the media pH in cell culture experiments to investigate the relationship between pH and cancer cell growth.

High-field asymmetric waveform ion mobility spectrometry for mass spectrometry-based proteomics.

Science.gov (United States)

Swearingen, Kristian E; Moritz, Robert L

2012-10-01

High-field asymmetric waveform ion mobility spectrometry (FAIMS) is an atmospheric pressure ion mobility technique that separates gas-phase ions by their behavior in strong and weak electric fields. FAIMS is easily interfaced with electrospray ionization and has been implemented as an additional separation mode between liquid chromatography (LC) and mass spectrometry (MS) in proteomic studies. FAIMS separation is orthogonal to both LC and MS and is used as a means of on-line fractionation to improve the detection of peptides in complex samples. FAIMS improves dynamic range and concomitantly the detection limits of ions by filtering out chemical noise. FAIMS can also be used to remove interfering ion species and to select peptide charge states optimal for identification by tandem MS. Here, the authors review recent developments in LC-FAIMS-MS and its application to MS-based proteomics.

A Pedagogical Framework for Mobile Learning: Categorizing Educational Applications of Mobile Technologies into Four Types

Directory of Open Access Journals (Sweden)

Yeonjeong Park

2011-02-01

Full Text Available Instructional designers and educators recognize the potential of mobile technologies as a learning tool for students and have incorporated them into the distance learning environment. However, little research has been done to categorize the numerous examples of mobile learning in the context of distance education, and few instructional design guidelines based on a solid theoretical framework for mobile learning exist. In this paper I compare mobile learning (m-learning with electronic learning (e-learning and ubiquitous learning (u-learning and describe the technological attributes and pedagogical affordances of mobile learning presented in previous studies. I modify transactional distance (TD theory and adopt it as a relevant theoretical framework for mobile learning in distance education. Furthermore, I attempt to position previous studies into four types of mobile learning: 1 high transactional distance socialized m-learning, 2 high transactional distance individualized m-learning, 3 low transactional distance socialized m-learning, and 4 low transactional distance individualized m-learning. As a result, this paper can be used by instructional designers of open and distance learning to learn about the concepts of mobile learning and how mobile technologies can be incorporated into their teaching and learning more effectively.

Decrease in Daphnia egg viability at elevated pH

NARCIS (Netherlands)

Vijverberg, J.; Kalf, D.F.; Boersma, M.

1996-01-01

The effect of high pH on the reproduction of two Daphnia galeata clones was experimentally investigated in the laboratory. We observed that the mortality of juveniles and adults did not increase with increasing pH in the range pH 9.0- 10.5, which agrees with what is generally reported in the

Optimization of urinary dipstick pH: Are multiple dipstick pH readings reliably comparable to commercial 24-hour urinary pH?

Science.gov (United States)

Abbott, Joel E; Miller, Daniel L; Shi, William; Wenzler, David; Elkhoury, Fuad F; Patel, Nishant D; Sur, Roger L

2017-09-01

Accurate measurement of pH is necessary to guide medical management of nephrolithiasis. Urinary dipsticks offer a convenient method to measure pH, but prior studies have only assessed the accuracy of a single, spot dipstick. Given the known diurnal variation in pH, a single dipstick pH is unlikely to reflect the average daily urinary pH. Our goal was to determine whether multiple dipstick pH readings would be reliably comparable to pH from a 24-hour urine analysis. Kidney stone patients undergoing a 24-hour urine collection were enrolled and took images of dipsticks from their first 3 voids concurrently with the 24-hour collection. Images were sent to and read by a study investigator. The individual and mean pH from the dipsticks were compared to the 24-hour urine pH and considered to be accurate if the dipstick readings were within 0.5 of the 24-hour urine pH. The Bland-Altman test of agreement was used to further compare dipstick pH relative to 24-hour urine pH. Fifty-nine percent of patients had mean urinary pH values within 0.5 pH units of their 24-hour urine pH. Bland-Altman analysis showed a mean difference between dipstick pH and 24-hour urine pH of -0.22, with an upper limit of agreement of 1.02 (95% confidence interval [CI], 0.45-1.59) and a lower limit of agreement of -1.47 (95% CI, -2.04 to -0.90). We concluded that urinary dipstick based pH measurement lacks the precision required to guide medical management of nephrolithiasis and physicians should use 24-hour urine analysis to base their metabolic therapy.

A High Speed Mobile Communication System implementing Bicasting Architecture on the IP Layer

OpenAIRE

Yamada, Kazuhiro

2012-01-01

Having a broadband connection on high speed rails is something that business travelers want most. Increasing number of passengers is requesting even higher access speeds. We are proposing the Media Convergence System as an ideal communication system for future high speed mobile entities. The Media Convergence System recognizes plural wireless communication media between the ground network and each train, and then traffic is load-balanced over active media which varies according to circumstanc...

The Impact of High-Speed Rail on Residents’ Travel Behavior and Household Mobility: A Case Study of the Beijing-Shanghai Line, China

Directory of Open Access Journals (Sweden)

Hongsheng Chen

2016-11-01

Full Text Available With the improvement of China’s high-speed rail network, there have been many economic and social benefits for local residents. Based on a questionnaire conducted in stations on the Beijing-Shanghai line, and through an analysis of high-speed rail passenger travel behavior and family relocation, we explored the social effects of high-speed rail. The study found that high-speed rail passengers are mainly young, highly educated, and have a middle to high income. However, with the popularization of high-speed rail, such differences in the social stratum of high-speed rail passengers are expected to disappear. Through an analysis of passenger travel status, we found that the areas surrounding high-speed rail stations are very accessible to the main cities, and are well connected by other public transport. With the emergence of the “high mobility era” based on the high-speed rail network, the separation of workplace and residence and the number of “double city” households are increasing, primarily in the Beijing-Tianjin and Shanghai-Nanjing (especially in Suzhou-Kunshan-Shanghai regions. In addition, high-speed rail introduces the possibility of household mobility, with 22.7% of the respondents in this study having relocated since the Beijing-Shanghai line opened. Household mobility is apparent primarily among big cities, with movement toward nearby cities. We also found that occupation, income, residence time, and schooling of children have a significant impact on households. With the improvement of high-speed rail networks, household mobility will become a common phenomenon and research on domestic mobility will continue to increase.

Adolescents' risk perceptions on mobile phones and their base stations, their trust to authorities and incivility in using mobile phones: a cross-sectional survey on 2240 high school students in Izmir, Turkey.

Science.gov (United States)

Hassoy, Hur; Durusoy, Raika; Karababa, Ali Osman

2013-01-25

Use of mobile phones has rapidly risen among adolescents despite a lack of scientific certainty on their health risks. Risk perception is an important determinant of behavior, and studies on adolescents' risk perceptions of mobile phones or base stations are very scarce. This study aims to evaluate high school students' risk perceptions on mobile phones and base stations, their trust to authorities, their opinions regarding incivility while using mobile phones and to assess associated factors. For this cross-sectional study, 2530 students were chosen with stratified cluster sampling among 20,493 high school students studying in Bornova district of Izmir, Turkey, among whom 2240 (88.5%) participated. Risk perceptions and opinions were questioned with a 5-point Likert scale for 24 statements grouped under four dimensions. The mean responses to the four dimensions were categorized as mobile phone, base station, trust to authority and incivility dimensions were 3.69 ± 0.89, 4.34 ± 0.78, 3.77 ± 0.93, 3.16 ± 0.93 and the prevalence of high risk perception was 65.1%, 86.7%, 66.2%, 39.7%, respectively. In the mobile phone dimension; students attending industrial technical high school had lower risk perceptions while female students, lower mothers' education groups and students not using mobile phones (OR = 2.82, 95% CI = 1.80-4.40) had higher risk perceptions. In the base station dimension girls had higher risk perceptions (OR = 1.68, 95% CI = 1.20-2.37). Girls and students attending industrial technical high school had significantly lower risk perception however 11-12th grade group perceived the risk higher (OR = 1.45 95% CI = 1.15-1.84) in the trust to authority dimension. For the incivility dimension, female students (OR = 1.44, 95% CI = 1.14-1.82), illiterate/only literate mothers (OR = 1.79, 95% CI = 1.04-2.75) and students not using mobile phones (OR = 2.50, 95% CI = 1.62-3.87) perceived higher risk. Understanding the effects of these determinants might aid in