Determination of saturated aliphatic hydrocarbons in vegetable oils

Energy Technology Data Exchange (ETDEWEB)

Gomez Coca, R.B.; Cert, R.; Perez Camino, M.C.; Moreda, W.

2016-07-01

The aim of this work is to inform about the development of a simple and reliable off-line method for the determination of saturated hydrocarbons (SH) in vegetable oils. SH can be used as markers for fuel or for mineral oil contamination in edible oils and fats. The method consists of the isolation of the fraction by LC on deactivated silver-silica gel and subsequent on-column GC-FID analysis. This stationary phase was prepared avoiding any kind of activation. The method was developed and validated through the participation in both a proficiency test organized by the Joint Research Centre of the European Commission, and a collaborative trial carried out with trained Spanish laboratories according to the standard ISO 5725. Results showed acceptable repeatability and reproducibility values, and Horrat index, being this protocol in use with satisfactory results ever since. The method’s LOQ is 15 mg·kg–1 and its LOD 5 mg·kg–1, which make it suitable to quantify the 50 mg·kg–1 limit established by the EU, and to detect mineral oil content within the 10–500 mg·kg–1 range. Although other procedures with lower LOD have been developed throughout the years, the use of just regular laboratory equipment such as GC-FID makes the proposed method appropriate for application on a routine basis. (Author)

Improvement of mineral oil saturated and aromatic hydrocarbons determination in edible oil by liquid-liquid-gas chromatography with dual detection.

Science.gov (United States)

Zoccali, Mariosimone; Barp, Laura; Beccaria, Marco; Sciarrone, Danilo; Purcaro, Giorgia; Mondello, Luigi

2016-02-01

Mineral oils, which are mainly composed of saturated hydrocarbons and aromatic hydrocarbons, are widespread food contaminants. Liquid chromatography coupled to gas chromatography with flame ionization detection represents the method of choice to determine these two families. However, despite the high selectivity of this technique, the presence of olefins (particularly squalene and its isomers) in some samples as in olive oils, does not allow the correct quantification of the mineral oil aromatic hydrocarbons fraction, requiring additional off-line tools to eliminate them. In the present research, a novel on-line liquid chromatography coupled to gas chromatography method is described for the determination of hydrocarbon contamination in edible oils. Two different liquid chromatography columns, namely a silica one (to retain the bulk of the matrix) and a silver-ion one (which better retains the olefins), were coupled in series to obtain the mineral oil aromatic hydrocarbons hump free of interfering peaks. Furthermore, the use of a simultaneous dual detection, flame ionization detector and triple quadrupole mass spectrometer allowed us not only to quantify the mineral oil contamination, but also to evaluate the presence of specific markers (i.e. hopanes) to confirm the petrogenic origin of the contamination. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Kolkhoung (Pistacia khinjuk Hull Oil and Kernel Oil as Antioxidative Vegetable Oils with High Oxidative Stability and Nutritional Value

Directory of Open Access Journals (Sweden)

Maryam Asnaashari

2015-01-01

Full Text Available In this study, in order to introduce natural antioxidative vegetable oil in food industry, the kolkhoung hull oil and kernel oil were extracted. To evaluate their antioxidant efficiency, gas chromatography analysis of the composition of kolkhoung hull and kernel oil fatty acids and high–performance liquid chromatography analysis of tocopherols were done. Also, the oxidative stability of the oil was considered based on the peroxide value and anisidine value during heating at 100, 110 and 120 °C. Gas chromatography analysis showed that oleic acid was the major fatty acid of both types of oil (hull and kernel and based on a low content of saturated fatty acids, high content of monounsaturated fatty acids, and the ratio of ω-6 and ω-3 polyunsaturated fatty acids, they were nutritionally well-balanced. Moreover, both hull and kernel oil showed high oxidative stability during heating, which can be attributed to high content of tocotrienols. Based on the results, kolkhoung hull oil acted slightly better than its kernel oil. However, both of them can be added to oxidation–sensitive oils to improve their shelf life.

Multivariate statisticalmethods applied to interpretation of saturated biomarkers (Velebit oil field, SE Pannonian Basin, Serbia

Directory of Open Access Journals (Sweden)

TATJANA SOLEVIC

2006-07-01

Full Text Available Twenty-five crude oils originating from the Velebit oil field (SE Pannonian Basin, the most important oil field in Serbia, were investigated. Saturated biomarkers (n-alkanes, isoprenoids, steranes and triterpanes were analyzed by gas chromatography-mass spectrometry (GC-MS. Based on the distribution and abundance of these compounds, a large number of source and maturation parameters were calculated, particularly those most often used in correlation studies of oils. The examined samples were classified according to their origin and level of thermal maturity using factor, cluster and discriminant analyses. According to the source and maturation parameters, combined factor and cluster analyses using the Ward method enabled the categorization of the investigated oils into three groups. The cluster Ward analysis was shown to be of greater susceptibility and reliability. However, in addition to the two aforementioned methods, K-Means cluster analysis and discriminant analysis were shown to be necessary for a more precise and detailed categorization in the case of a large number of samples in one group. Consequently, it was concluded that factor and cluster K-Means andWard analyses can generally be used for the interpretation of saturated biomarkers in correlation studies of oils, but the observed results have to be checked, i.e., confirmed by discriminant analysis.

Experimental investigation of wettability alteration on residual oil saturation using nonionic surfactants: Capillary pressure measurement

Directory of Open Access Journals (Sweden)

Masoud Amirpour

2015-12-01

Full Text Available Introducing the novel technique for enhancing oil recovery from available petroleum reservoirs is one of the important issues in future energy demands. Among of all operative factors, wettability may be the foremost parameter affecting residual oil saturation in all stage of oil recovery. Although wettability alteration is one of the methods which enhance oil recovery from the petroleum reservoir. Recently, the studies which focused on this subject were more than the past and many contributions have been made on this area. The main objective of the current study is experimentally investigation of the two nonionic surfactants effects on altering wettability of reservoir rocks. Purpose of this work is to change the wettability to preferentially the water-wet condition. Also reducing the residual oil saturation (Sor is the other purpose of this work. The wettability alteration of reservoir rock is measured by two main quantitative methods namely contact angle and the USBM methods. Results of this study showed that surfactant flooding is more effective in oil-wet rocks to change their wettability and consequently reducing Sor to a low value. Cedar (Zizyphus Spina Christi is low priced, absolutely natural, and abundantly accessible in the Middle East and Central Asia. Based on the results, this material can be used as a chemical surfactant in field for enhancing oil recovery.

Inelastic neutron scattering reactions in fluid saturated rock as exploited in oil well logging

International Nuclear Information System (INIS)

Underwood, M.C.; Dyos, C.J.

1986-01-01

Oil saturated sandstone and limestone targets have been irradiated with 14 MeV neutrons. Gamma-ray spectra were accumulated and the γ-ray intensities arising from inelastic neutron scattering reactions upon carbon and oxygen measured. The results are compared with the predictions of a simple model. They enable some features of the response of (n,γ) tools used in oil well logging to be established and current uncertainties in understanding to be highlighted. (author)

Modification of high saturated fat diet with n-3 polyunsaturated fat improves glucose intolerance and vascular dysfunction

Science.gov (United States)

Lamping, KL; Nuno, DW; Coppey, LJ; Holmes, AJ; Hu, S; Oltman, CL; Norris, AW; Yorek, MA

2013-01-01

Aims The ability of dietary enrichment with monounsaturated (MUFA), n-3, or n-6 polyunsaturated fatty acids (PUFA) to reverse glucose intolerance and vascular dysfunction resulting from excessive dietary saturated fatty acids is not resolved. We hypothesized that partial replacement of dietary saturated fats with n-3 PUFA enriched menhaden oil (MO) would provide greater improvement in glucose tolerance and vascular function compared to n-6 enriched safflower oil (SO) or MUFA-enriched olive oil (OO). Material and Methods We fed mice a high saturated fat diet (60% kcal from lard) for 12 weeks before substituting half the lard with MO, SO or OO for an additional 4 weeks. At the end of 4 weeks, we assessed glucose tolerance, insulin signaling and reactivity of isolated pressurized gracilis arteries. Results After 12 weeks of saturated fat diet, body weights were elevated and glucose tolerance abnormal compared to mice on control diet (13% kcal lard). Diet substituted with MO restored basal glucose levels, glucose tolerance, and indices of insulin signaling (phosphorylated Akt) to normal whereas restoration was limited for SO and OO substitutions. Although dilation to acetylcholine was reduced in arteries from mice on HF, OO and SO diets compared to normal diet, dilation to acetylcholine was fully restored and constriction to phenylephrine reduced in MO fed mice compared to normal. Conclusion We conclude that short term enrichment of an ongoing high fat diet with n-3 PUFA rich MO but not MUFA rich OO or n-6 PUFA rich SO reverses glucose tolerance, insulin signaling, and vascular dysfunction. PMID:22950668

Long term highly saturated fat diet does not induce NASH in Wistar rats

Directory of Open Access Journals (Sweden)

Filippi Céline

2007-02-01

Full Text Available Abstract Background Understanding of nonalcoholic steatohepatitis (NASH is hampered by the lack of a suitable model. Our aim was to investigate whether long term high saturated-fat feeding would induce NASH in rats. Methods 21 day-old rats fed high fat diets for 14 weeks, with either coconut oil or butter, and were compared with rats feeding a standard diet or a methionine choline-deficient (MCD diet, a non physiological model of NASH. Results MCDD fed rats rapidly lost weight and showed NASH features. Rats fed coconut (86% of saturated fatty acid or butter (51% of saturated fatty acid had an increased caloric intake (+143% and +30%. At the end of the study period, total lipid ingestion in term of percentage of energy intake was higher in both coconut (45% and butter (42% groups than in the standard (7% diet group. No change in body mass was observed as compared with standard rats at the end of the experiment. However, high fat fed rats were fattier with enlarged white and brown adipose tissue (BAT depots, but they showed no liver steatosis and no difference in triglyceride content in hepatocytes, as compared with standard rats. Absence of hepatic lipid accumulation with high fat diets was not related to a higher lipid oxidation by isolated hepatocytes (unchanged ketogenesis and oxygen consumption or hepatic mitochondrial respiration but was rather associated with a rise in BAT uncoupling protein UCP1 (+25–28% vs standard. Conclusion Long term high saturated fat feeding led to increased "peripheral" fat storage and BAT thermogenesis but did not induce hepatic steatosis and NASH.

Reflection of processes of non-equilibrium two-phase filtration in oil-saturated hierarchical medium in data of active wave geophysical monitoring

Science.gov (United States)

Hachay, Olga; Khachay, Andrey; Khachay, Oleg

2016-04-01

The processes of oil extraction from deposit are linked with the movement of multi-phase multi-component media, which are characterized by non-equilibrium and non-linear rheological features. The real behavior of layered systems is defined by the complexity of the rheology of moving fluids and the morphology structure of the porous medium, and also by the great variety of interactions between the fluid and the porous medium [Hasanov and Bulgakova, 2003]. It is necessary to take into account these features in order to informatively describe the filtration processes due to the non-linearity, non-equilibrium and heterogeneity that are features of real systems. In this way, new synergetic events can be revealed (namely, a loss of stability when oscillations occur, and the formation of ordered structures). This allows us to suggest new methods for the control and management of complicated natural systems that are constructed on account of these phenomena. Thus the layered system, from which it is necessary to extract the oil, is a complicated dynamical hierarchical system. A comparison is provided of non-equilibrium effects of the influence of independent hydrodynamic and electromagnetic induction on an oil layer and the medium which it surrounds. It is known that by drainage and steeping the hysteresis effect on curves of the relative phase permeability in dependence on the porous medium's water saturation in some cycles of influence (drainage-steep-drainage) is observed. Using the earlier developed 3D method of induction electromagnetic frequency geometric monitoring, we showed the possibility of defining the physical and structural features of a hierarchical oil layer structure and estimating the water saturation from crack inclusions. This effect allows managing the process of drainage and steeping the oil out of the layer by water displacement. An algorithm was constructed for 2D modeling of sound diffraction on a porous fluid-saturated intrusion of a hierarchical

Prediction of saturation using the carbon/oxygen log

Energy Technology Data Exchange (ETDEWEB)

Horner, S.C.; Sanyal, S.K.

1984-09-01

This project investigates the nature of Dresser-Atlas Carbon/Oxygen Log gamma ray spectra. It presents an attempt to improve the signal-to-noise ratio of the C/O and Si/Ca parameters used by Dresser-Atlas to determine oil saturation. Two techniques were developed to subtract the Compton background from the spectral data. Neither technique significantly improves the accuracy of the cased-hole prediction of oil saturation. However, it has been shown that it is possible to develop a satisfactory correlation for oil saturation on a well-by-well basis. This correlation can then be used to generate oil-in-place from the C/O and Si/Ca ratios. 17 references.

Registration of the sunflower oilseed maintainer genetic stocks HOLS1, HOLS2, HOLS3, and HOLS4, possessing genes for high oleic and low saturated fatty acids, and tolerance to imidazolinone herbicides

Science.gov (United States)

One of the primary goals for the oilseed sunflower industry is to provide novel oil products for human consumption. One oil profile of particular interest is high oleic/ low saturated fat, because it combines high oxidative stability of the oil with a reduction in the fatty acids that are detriment...

High speed drying of saturated steam

International Nuclear Information System (INIS)

Marty, C.; Peyrelongue, J.P.

1993-01-01

This paper describes the development of the drying process for the saturated steam used in the PWR nuclear plant turbines in order to prevent negative effects of water on turbine efficiency, maintenance costs and equipment lifetime. The high speed drying concept is based on rotating the incoming saturated steam in order to separate water which is more denser than the steam; the water film is then extracted through an annular slot. A multicellular modular equipment has been tested. Applications on high and low pressure extraction of various PWR plants are described (Bugey, Loviisa)

Pore network modelling of heavy oil depressurization : a parametric study of factors affecting critical gas saturation and three-phase relative permeabilities

Energy Technology Data Exchange (ETDEWEB)

Bondino, I.; McDougall, S.D. [Heriot-Watt Univ., Edinburgh, Scotland (United Kingdom); Hamon, G. [TotalFina Elf Exploration and Production (France)

2002-07-01

A review of how the bubble nucleation process affects the efficiency of heavy oil recovery was presented along with a discussion regarding a pore-scale simulator technique to depressurize heavy oil systems. A light oil depressurization simulation is also presented in which a straightforward instantaneous nucleation (IN) model and a more intricate progressive nucleation (PN) model have been used. Simulation results are compared to those derived from the heavy oil systems. The nucleation of bubbles, their growth by solute diffusion and expansion, plus the final stages of coalescence migration and production are the main steps in the depressurization process which were accounted for in a 3-phase simulator. The model can also determine the impact of bubble density and gas-oil diffusion coefficient on critical gas saturation and 3-phase relative permeability. The difference in results for light and heavy oils was also highlighted. In the first scenario, the evolution of gas was characterized by embryonic bubbles that are quickly and randomly nucleated once bubble-point pressure is reached. A stochastic algorithm was developed for PN from experimental observations. IN and PN observations were not necessarily contradictory. It was determined that the high interfacial tension of heavy oils leads to a more compact, capillary-dominated pattern of gas evolution compared to light oils, resulting in improved recoveries for heavy oil systems. 23 refs., 6 tabs., 23 figs.

A mind cleared by walnut oil: The effects of polyunsaturated and saturated fat on extinction learning.

Science.gov (United States)

Miller, Holly C; Struyf, Dieter; Baptist, Pascale; Dalile, Boushra; Van Oudenhove, Lukas; Van Diest, Ilse

2018-04-07

The treatment of anxiety-based psychopathology often hinges upon extinction learning. Research in nutritional neuroscience has observed that the regular consumption of perilla oil (50% alpha-linolenic acid (ALA)) facilitates extinction learning in rats (Yamamoto et al., 1988). However, acute facilitation of extinction learning by oils rich in ALA has not been reported for rats or humans, though the acute consumption of rapeseed oil (10% ALA) has been observed to improve cognitive processing speed in humans (Jones, Sünram-Lea, & Wesnes, 2012). For this reason, the present laboratory work examined the effects of adding walnut oil (12% ALA) to a chocolate milkshake on the acquisition, generalization, and extinction of a fear-based prediction in young adults. It compared performance between subjects. The other participants consumed a similar milkshake with either an equicaloric amount of cream (saturated fat), or with no added fat (control). Acquisition and generalization of the fear-based prediction were similar for all groups. However, those who consumed walnut oil extinguished most rapidly and profoundly. Implications for extinction learning are discussed. Copyright © 2018. Published by Elsevier Ltd.

Mobility Effect on Poroelastic Seismic Signatures in Partially Saturated Rocks With Applications in Time-Lapse Monitoring of a Heavy Oil Reservoir

Science.gov (United States)

Zhao, Luanxiao; Yuan, Hemin; Yang, Jingkang; Han, De-hua; Geng, Jianhua; Zhou, Rui; Li, Hui; Yao, Qiuliang

2017-11-01

Conventional seismic analysis in partially saturated rocks normally lays emphasis on estimating pore fluid content and saturation, typically ignoring the effect of mobility, which decides the ability of fluids moving in the porous rocks. Deformation resulting from a seismic wave in heterogeneous partially saturated media can cause pore fluid pressure relaxation at mesoscopic scale, thereby making the fluid mobility inherently associated with poroelastic reflectivity. For two typical gas-brine reservoir models, with the given rock and fluid properties, the numerical analysis suggests that variations of patchy fluid saturation, fluid compressibility contrast, and acoustic stiffness of rock frame collectively affect the seismic reflection dependence on mobility. In particular, the realistic compressibility contrast of fluid patches in shallow and deep reservoir environments plays an important role in determining the reflection sensitivity to mobility. We also use a time-lapse seismic data set from a Steam-Assisted Gravity Drainage producing heavy oil reservoir to demonstrate that mobility change coupled with patchy saturation possibly leads to seismic spectral energy shifting from the baseline to monitor line. Our workflow starts from performing seismic spectral analysis on the targeted reflectivity interface. Then, on the basis of mesoscopic fluid pressure diffusion between patches of steam and heavy oil, poroelastic reflectivity modeling is conducted to understand the shift of the central frequency toward low frequencies after the steam injection. The presented results open the possibility of monitoring mobility change of a partially saturated geological formation from dissipation-related seismic attributes.

Use of adsorption and gas chromatographic techniques in estimating biodegradation of indigenous crude oils

International Nuclear Information System (INIS)

Kokub, D.; Allahi, A.; Shafeeq, M.; Khalid, Z.M.; Malik, K.A.; Hussain, A.

1993-01-01

Indigenous crude oils could be degraded and emulsified upto varying degree by locally isolated bacteria. Degradation and emulsification was found to be dependent upon the chemical composition of the crude oils. Tando Alum and Khashkheli crude oils were emulsified in 27 and 33 days of incubation respectively. While Joyamair crude oil and not emulsify even mainly due to high viscosity of this oil. Using adsorption chromatographic technique, oil from control (uninoculated) and bio degraded flasks was fractioned into the deasphaltened oil containing saturate, aromatic, NSO (nitrogen, sulphur, oxygen) containing hydrocarbons) and soluble asphaltenes. Saturate fractions from control and degraded oil were further analysed by gas liquid chromatography. From these analyses, it was observed that saturate fraction was preferentially utilized and the crude oils having greater contents of saturate fraction were better emulsified than those low in this fraction. Utilization of various fractions of crude oils was in the order saturate> aromatic> NSO. (author)

The Effects of Massage with Coconut and Sunflower Oils on Oxygen Saturation of Premature Infants with Respiratory Distress Syndrome Treated With Nasal Continuous Positive Airway Pressure

Directory of Open Access Journals (Sweden)

Sousan Valizadeh

2012-11-01

Full Text Available Introduction: Nowadays particular emphasis is placed on the developmental aspects of premature infants care. Massage therapy is one of the best-known methods of caring. Due to the minimal touch policy in neonatal intensive care units (NICUs, massaging is not usually performed on premature infants. However, there is not sufficient evidence to support the claim that newborn infants with complex medical conditions should not be massaged. This study aimed to determine the effects of massage with coconut and sunflower oils on oxygen saturation of infants with respiratory distress syndrome (RDS treated with nasal continuous positive airway pressure (NCPAP. Methods: This was a randomized controlled trial on 90 newborns who were admitted to Alzahra Hospital (Tabriz, Iran. The infants were divided into control and massage therapy groups (massage with coconut and sunflower oils. Data was collected using a hospital documentation form. A 15-minute daily massage was performed for 3 days. Respiratory rate (RR, fraction of inspired oxygen (FiO2 and oxygen saturation were measured 5 minutes before the massage, 3 times during the massage, and 5 minutes after the massage. The collected data was analyzed using a mixed model. Results: In comparison to coconut oil and control groups, mean oxygen saturation of sunflower oil group was improved. In addition, the coconut massage group showed lower oxygen saturation than the control group but was all values were within the normal range. Although massage decreased oxygen saturation, there was no need to increase FiO2. Conclusion: Massage therapy can provide developmental care for infants treated with NCPAP.

Effect of the distribution of saturated fatty acids in the melting and crystallization profiles of high-oleic high-stearic oils; Efecto de la distribución de los ácidos grasos saturados en los perfiles de fusión y cristalización de los aceites alto esteárico alto oleico

Energy Technology Data Exchange (ETDEWEB)

Bootello, M.A.; Garces, R.; Martinez-Force, E.; Salas, J.J.

2016-07-01

The composition and distribution of fatty acids in triacylglycerol (TAG) molecules are commonly considered as factors that determine the physical properties of a given oil or fat. The distribution of any fatty acid in fats and oils can be described through the α coefficient of asymmetry, which can be calculated from the TAG composition and fatty acid composition of the Sn-2 position of the TAGs determined through lipase hydrolysis. High-oleic high-stearic oils and fats are considered stable and healthy, and they are good substitutes for hydrogenated vegetable oils and palm fractions in many food products, such as spreads and confectionery. Here, different high-oleic high-stearic acid oils were formulated which contained different distributions of saturated fatty acids in their TAGs, while maintaining a similar fatty acid composition. The aim of this work was to discuss the possibility of using the α coefficient to predict the physical properties of fats in function of their chemical composition and their melting and crystallization behavior as examined by differential scanning calorimetry.

Nonlinear acoustics of water-saturated marine sediments

DEFF Research Database (Denmark)

Jensen, Leif Bjørnø

1976-01-01

Interest in the acoustic qualities of water-saturated marine sediments has increased considerably during recent years. The use of sources of high-intensity sound in oil propsecting, in geophysical and geological studies of bottom and subbottom materials and profiles and recently in marine...... archaeology has emphasized the need of information about the nonlinear acoustic qualities of water-saturated marine sediments. While the acoustic experiments and theoretical investigations hitherto performed have concentrated on a determination of the linear acoustic qualities of water-saturated marine...... sediments, their parameters of nonlinear acoustics are still unexplored. The strong absorption, increasing about linearly with frequency, found in most marine sediments and the occurrence of velocity dispersion by some marine sediments restrict the number of nonlinear acoustic test methods traditionally...

Analysis of physical characteristics of vegetable oils

Energy Technology Data Exchange (ETDEWEB)

Piamba Tulcan, Oscar Edwin [Universidade Nacional da Colombia (UNAL), Bogota (Colombia). Fac. de Ingenieria; Universidade Federal Fluminense (PGMEC/UFF), Niteroi, RJ (Brazil). Programa de Pos-Graduacao em Engenharia Mecanica], E-mail: oepiambat@unal.edu.co; Andrade, Danielle Oliveira de; Andrade, Ednilton Tavares de [Universidade Federal Fluminense (TER/UFF), Niteroi, RJ (Brazil). Dept. de Engenharia Agricola e do Meio Ambiente; Pereira, Roberto Guimaraes [Universidade Federal Fluminense (TER/UFF), Niteroi, RJ (Brazil). Dept. de Engenharia Mecanica

2008-07-01

Different vegetable oils were characterized using standardized methods. The evaluated characteristics were density, viscosity, flow point, cloud point and corrosion. The obtained data was tabulated and compared with average composition values of oils in percentage of fatty acids and iodine number for each oil. In this analysis it is shown that viscosity decreases with the increase of the iodine number, and density decrease. The cloud and flow point have greater relation with the presence of saturated or highly unsaturated fatty acids, respectively. The index of corrosion is greater when oil saturation or its iodine number are increased. (author)

Super-Hydrophobic High Throughput Electrospun Cellulose Acetate (CA) Nanofibrous Mats as Oil Selective Sorbents

Science.gov (United States)

Han, Chao

The threat of oil pollution increases with the expansion of oil exploration and production activities, as well as the industrial growth around the world. Use of sorbents is a common method to deal with the oil spills. In this work, an advanced sorbent technology is described. A series of non-woven Cellulose Acetate (CA) nanofibrous mats with a 3D fibrous structure were synthesized by a novel high-throughput electrospinning technique. The precursor was solutions of CA/ acetic acid-acetone in various concentrations. Among them, 15.0% CA exhibits a superhydrophobic surface property, with a water contact angle of 128.95°. Its oil sorption capacity is many times higher the oil sorption capacity of the best commercial sorbent available in the market. Also, it showed good buoyancy properties on the water both as dry-mat and oil-saturated mat. In addition, it is biodegradable, easily available, easily manufactured, so the CA nanofibrous mat is an excellent candidate as oil sorbent for oil spill in water treatment.

Partially acetylated sugarcane bagasse for wicking oil from contaminated wetlands

Energy Technology Data Exchange (ETDEWEB)

Chung, S. [Samsung Engineering Co. Ltd., R and D Center, Suwon, Gyeonggi (Korea, Republic of); Suidan, M.T. [University of Cincinnati, School of Energy, Environmental, Biological and Medical Engineering, Cincinnati, OH (United States); Venosa, A.D. [NRMRL, U.S. EPA, Cincinnati, OH (United States)

2011-12-15

Sugarcane bagasse was partially acetylated to enhance its oil-wicking ability in saturated environments while holding moisture for hydrocarbon biodegradation. The water sorption capacity of raw bagasse was reduced fourfold after treatment, which indicated considerably increased hydrophobicity but not a limited capability to hold moisture for hydrocarbon biodegradation. Characterization results by Fourier transform infrared (FT-IR), scanning electron microscopy (SEM), X-ray diffraction (XRD), and surface area analyzer suggested that treated bagasse exhibited enhanced hydrophobicity and surface area. Oil wicking test results indicate that treated bagasse is more effective in wicking oil from highly saturated environments than raw bagasse and suggest that application of this material in remediation of oil spills in highly saturated wetlands is promising. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Analysis of quality of the biogasoils of palm oil and castor oil

International Nuclear Information System (INIS)

Benjumea, Pedro Nel; Agudelo, Jhon Ramiro; Benavides, Alirio Yovany

2004-01-01

Biodiesel is a fuel made from raw materials of renewable origin such as vegetable oils. The objective of this work is to make a quality analysis of two types of biodiesel made from raw materials available in Colombia such as palm oil and castor oil. Biodiesel from palm oil complies with the majority of technical requirements specified by ASTM standards D-975 y D-6751. A high cloud point is the main drawback of this kind of biodiesel. This is a consequence of its highly saturated chemical nature. On the other hand, biodiesel from castor oil presents more difficulties in order to be used in diesel engines because of having a low cetane index and a high viscosity

Analysis of the saturated hydrocarbon in coal, carbonaceous mudstone and oils from the lower Jurassic coal measures in the Turpan Basin by GC/MS

International Nuclear Information System (INIS)

Fang Xuan; Meng Qianxiang; Sun Minzhuo; Du Li; Ding Wanren

2005-01-01

Saturated hydrocarbon of coal, carbonaceous mudstone and oils from the Lower Jurassic coal measures in the Turpan basin were studied, and biomarker characteristics and coal thermal maturity analyzed to draw the following conclusions. T here are many similar biomarker characteristics between oil from middle-lower Jurassic of Turpan Basin and coal and carbonaceous mudstone in the same strata. They all contain specific r-lupane, I-norbietane, C 24 -tetracyclic and high content of C 29 -steranes. These characteristics suggest that they have similar matter source of the organic matter derived from matter with abundant high plants. Meanwhile, biomarkers often used to indicate depositional environments characterized by high Pr/Ph ratio, little or no gammacerane and high abundance dibenzofurans, such biomarker distributions are indicative of suboxic and freshwater environment. Although coal and carbonaceous mudstone remain in lower thermal maturity (Ro=0.47-0.53), but C 29 -ββ/(αα+ββ) sterane ratio (0.294-0.489) and bezohopane are detected. Because these ferture are related to bacterial activity, bacterial degradation of organic matter maybe take an important role in coal-derived oil. (authors)

Replacement of Dietary Saturated Fat by PUFA-Rich Pumpkin Seed Oil Attenuates Non-Alcoholic Fatty Liver Disease and Atherosclerosis Development, with Additional Health Effects of Virgin over Refined Oil

NARCIS (Netherlands)

Mulder, P.; Stavro, P.M.; Manuel Suárez, M.; Arola-Arnal, A.; Duyvenvoorde, W. van; Kooistra, T.; Wielinga, P.Y.; Kleemann, R.

2015-01-01

Background and Aims As dietary saturated fatty acids are associated with metabolic and cardiovascular disease, a potentially interesting strategy to reduce disease risk is modification of the quality of fat consumed. Vegetable oils represent an attractive target for intervention, as they largely

Replacement of dietary saturated fat by PUFA-rich pumpkin seed oil attenuates non-alcoholic fatty liver disease and atherosclerosis development, with additional health effects of virgin over refined oil

NARCIS (Netherlands)

Morrison, M.C.; Mulder, Petra; Stavro, P.M.; Suárez, Manuel; Arola-Arnal, Anna; Duyvenvoorde, Van Wim; Kooistra, Teake; Wielinga, P.Y.; Kleemann, Robert

2015-01-01

Background and Aims: As dietary saturated fatty acids are associated with metabolic and cardiovascular disease, a potentially interesting strategy to reduce disease risk is modification of the quality of fat consumed. Vegetable oils represent an attractive target for intervention, as they largely

Sequential Isolation of Saturated, Aromatic, Resinic and Asphaltic Fractions Degrading Bacteria from Oil Contaminated Soil in South Sumatera

Directory of Open Access Journals (Sweden)

Pingkan Aditiawati

2012-04-01

Full Text Available Sequential isolation has been conducted to obtain isolates of saturated, aromatic, resin, and asphaltene fractions degrading bacteria from oil contaminated sites. Five soil samples were collected from South Sumatera. These were analyzed using soil extract medium enriched with oil recovery or Remaining-Oil recovery Degradated (ROD as sole carbon and energy sources according to the isolation stage. ROD at the end of every isolation stage analyzed oil fractions by use of the SARA analysis method. Six isolates of bacteria have been selected, one isolate was fraction saturates degrading bacteria that are Mycobacterium sp. T1H2D4-7 at degradation rate 0.0199 mgs/h with density 8.4x106 cfu/g from stage I. The isolate T2H1D2-4, identified as Pseudomonas sp. was fraction aromatics degrading bacteria at accelerate 0.0141 mgs/h with density 5.1x106 cfu/g are obtained at stage II. Two isolates namely Micrococcus sp. T3H2D4-2 and Pseudomonas sp. T1H1D5-5 were fraction resins degrading bacteria by accelerate 0.0088 mgs/h at density 5.6x106 cfu/g and 0.0089 mgs/h at density 5.7x106 cfu/g are obtained at stage III. Isolation of stage IV has been obtained two isolates Pseudomonas sp. T4H1D3-1and Pseudomonas sp. T4H3D5-4 were fraction asphaltenes degrading bacteria by accelerate 0.0057 mgs/h at density 5.6x106 cfu/g and accelerate 0.0058 mgs/h at density 5.7x106 cfu/g.

Reactivity of dolomite in water-saturated supercritical carbon dioxide: Significance for carbon capture and storage and for enhanced oil and gas recovery

International Nuclear Information System (INIS)

Wang Xiuyu; Alvarado, Vladimir; Swoboda-Colberg, Norbert; Kaszuba, John P.

2013-01-01

Highlights: ► Dolomite reactivity with wet and dry supercritical CO 2 were evaluated. ► Dolomite does not react with dry CO 2 . ► H 2 O-saturated supercritical CO 2 dissolves dolomite and precipitates carbonate mineral. ► Temperature/reaction time control morphology and extent of carbonate mineralization. ► Reaction with wet CO 2 may impact trapping, caprock integrity, and CCS/EOR injectivity. - Abstract: Carbon dioxide injection in porous reservoirs is the basis for carbon capture and storage, enhanced oil and gas recovery. Injected carbon dioxide is stored at multiple scales in porous media, from the pore-level as a residual phase to large scales as macroscopic accumulations by the injection site, under the caprock and at reservoir internal capillary pressure barriers. These carbon dioxide saturation zones create regions across which the full spectrum of mutual CO 2 –H 2 O solubility may occur. Most studies assume that geochemical reaction is restricted to rocks and carbon dioxide-saturated formation waters, but this paradigm ignores injection of anhydrous carbon dioxide against brine and water-alternating-gas flooding for enhanced oil recovery. A series of laboratory experiments was performed to evaluate the reactivity of the common reservoir mineral dolomite with water-saturated supercritical carbon dioxide. Experiments were conducted at reservoir conditions (55 and 110 °C, 25 MPa) and elevated temperature (220 °C, 25 MPa) for approximately 96 and 164 h (4 and 7 days). Dolomite dissolves and new carbonate mineral precipitates by reaction with water-saturated supercritical carbon dioxide. Dolomite does not react with anhydrous supercritical carbon dioxide. Temperature and reaction time control the composition, morphology, and extent of formation of new carbonate minerals. Mineral dissolution and re-precipitation due to reaction with water-saturated carbon dioxide may affect the contact line between phases, the carbon dioxide contact angle, and the

Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

Directory of Open Access Journals (Sweden)

Li Benkai

2016-08-01

Full Text Available Vegetable oil can be used as a base oil in minimal quantity of lubrication (MQL. This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force, and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grinding temperature, and energy ratio coefficient of MQL grinding were compared among the seven vegetable oil types. Results revealed that (1 castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient; (2 palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient; (3 MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil; (4 viscosity significantly influences grinding force and grinding temperature to a greater extent than fatty acid varieties and contents in vegetable oils; (5 although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less viscous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature; (6 saturated fatty acid is a more efficient lubricant than unsaturated fatty acid; and (7 a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force, 87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7% energy

Canola Oil in Lactating Dairy Cow Diets Reduces Milk Saturated Fatty Acids and Improves Its Omega-3 and Oleic Fatty Acid Content.

Science.gov (United States)

Welter, Katiéli Caroline; Martins, Cristian Marlon de Magalhães Rodrigues; de Palma, André Soligo Vizeu; Martins, Mellory Martinson; Dos Reis, Bárbara Roqueto; Schmidt, Bárbara Laís Unglaube; Saran Netto, Arlindo

2016-01-01

To produce milk that is healthier for human consumption, the present study evaluated the effect of including canola oil in the diet of dairy cows on milk production and composition as well as the nutritional quality of this milk fat. Eighteen Holstein cows with an average daily milk yield of 22 (± 4) kg/d in the middle stage of lactation were used. The cows were distributed in 6 contemporary 3x3 Latin squares consisting of 3 periods and 3 treatments: control diet (without oil), 3% inclusion of canola oil in the diet and 6% inclusion of canola oil in the diet (dry matter basis). The inclusion of 6% canola oil in the diet of lactating cows linearly reduced the milk yield by 2.51 kg/d, short-chain fatty acids (FA) by 41.42%, medium chain FA by 27.32%, saturated FA by 20.24%, saturated/unsaturated FA ratio by 39.20%, omega-6/omega-3 ratio by 39.45%, and atherogenicity index by 48.36% compared with the control treatment. Moreover, with the 6% inclusion of canola oil in the diet of cows, there was an increase in the concentration of long chain FA by 45.91%, unsaturated FA by 34.08%, monounsaturated FA by 40.37%, polyunsaturated FA by 17.88%, milk concentration of omega-3 by 115%, rumenic acid (CLA) by 16.50%, oleic acid by 44.87% and h/H milk index by 94.44% compared with the control treatment. Thus, the inclusion of canola oil in the diet of lactating dairy cows makes the milk fatty acid profile nutritionally healthier for the human diet; however, the lactating performance of dairy cows is reduce.

Third harmonic current injection into highly saturated multi-phase machines

Directory of Open Access Journals (Sweden)

Klute Felix

2017-03-01

Full Text Available One advantage of multi-phase machines is the possibility to use the third harmonic of the rotor flux for additional torque generation. This effect can be maximised for Permanent Magnet Synchronous Machines (PMSM with a high third harmonic content in the magnet flux. This paper discusses the effects of third harmonic current injection (THCI on a five-phase PMSM with a conventional magnet shape depending on saturation. The effects of THCI in five-phase machines are shown in a 2D FEM model in Ansys Maxwell verified by measurement results. The results of the FEM model are analytically analysed using the Park model. It is shown in simulation and measurement that the torque improvement by THCI increases significantly with the saturation level, as the amplitude of the third harmonic flux linkage increases with the saturation level but the phase shift of the rotor flux linkage has to be considered. This paper gives a detailed analysis of saturation mechanisms of PMSM, which can be used for optimizing the efficiency in operating points of high saturations, without using special magnet shapes.

Injection halos of hydrocarbons above oil-gas fields with super-high pressures

Energy Technology Data Exchange (ETDEWEB)

Bakhtin, V.V.

1979-09-01

We studied the origin of injection halos of hydrocarbons above oil-gas fields with anomalously high formation pressures (AHFP). Using fields in Azerbaydzhan and Chechen-Ingushetiya as an example, we demonstrate the effect of certain factors (in particular, faults and zones of increased macro- and micro-jointing) on the morpholoy of the halos. The intensity of micro-jointing (jointing permeability, three-dimensional density of micro-jointing) is directly connected with vertical dimensions of the halos. We measured halos based on transverse profiles across the Khayan-Kort field and studied the distribution of bitumen saturation within the injection halo. Discovery of injection halos during drilling has enabled us to improve the technology of wiring deep-seated exploratory wells for oil and gas in regions with development of AHFP.

Purification of trona ores by conditioning with an oil-in-water emulsion

Science.gov (United States)

Miller, J. D.; Wang, Xuming; Li, Minhua

2009-04-14

The present invention is a trona concentrate and a process for floating gangue material from trona ore that comprises forming an emulsion, conditioning the trona ore at a high solids content in a saturated trona suspension, and then floating and removing the gangue material. The process for separating trona from gangue materials in trona ore can include emulsifying an oil in an aqueous solution to form an oil-in-water emulsion. A saturated trona suspension having a high solids content can also be formed having trona of a desired particle size. The undissolved trona in the saturated suspension can be conditioned by mixing the saturated suspension and the oil-in-water emulsion to form a conditioning solid suspension of trona and gangue material. A gas can be injected through the conditioning solid suspension to float the gangue material. Thus, the floated gangue material can be readily separated from the trona to form a purified trona concentrate without requirements of additional heat or other expensive processing steps.

CT-scan-monitored electrical-resistivity measurements show problems achieving homogeneous saturation

International Nuclear Information System (INIS)

Sprunt, E.S.; Davis, R.M.; Muegge, E.L.; Desai, K.P.

1991-01-01

This paper reports on x-ray computerized tomography (CT) scans obtained during measurement of the electrical resistivity of core samples which revealed some problems in obtaining uniform saturation along the lengths of the samples. The electrical resistivity of core samples is measured as a function of water saturation to determine the saturation exponent used in electric-log interpretation. An assumption in such tests is that the water saturation is uniformly distributed. Failure of this assumption can result in errors in the determination of the saturation exponent. Three problems were identified in obtaining homogeneous water saturation in two samples of a Middle Eastern carbonate grainstone: a stationary front formed in one sample at 1-psi oil/brine capillary pressure, a moving front formed at oil/brine capillary pressure ≤4 psi in samples tested in fresh mixed-wettability and cleaned water-wet states, and the heterogeneous fluid distribution caused by a rapidly moving front did not dissipate when the capillary pressure was eliminated in the samples

Quantitative 1D saturation profiles on chalk by NMR

DEFF Research Database (Denmark)

Olsen, Dan; Topp, Simon; Stensgaard, Anders

1996-01-01

Quantitative one-dimensional saturation profiles showing the distribution of water and oil in chalk core samples are calculated from NMR measurements utilizing a 1D CSI spectroscopy pulse sequence. Saturation profiles may be acquired under conditions of fluid flow through the sample. Results reveal...

A Contribution to the Problem of Initiation of a Combustion Source in an Oil-Saturated Bed

Science.gov (United States)

Koznacheev, I. A.; Dobrego, K. V.

2013-11-01

The problem on in-situ self-ignition of an oil-saturated bed under the conditions of forced filtration of an oxygen-containing gas has been solved with analytical and numerical methods with account of the burnout of a deficient gas component. The influence of the burnout of this component and of convective removal of heat from the bed on the time of its self-ignition has been determined. Recommendations for the optimum regime of initiation of the self-ignition of the bed with account of variation of the blast flow rate and the oxygen content have been given.

The oil market towards 2030 - can OPEC combine high oil price with high market share

International Nuclear Information System (INIS)

Aune, Finn Roar; Glomsroed, Solveig; Lindholt, Lars; Rosendahl, Knut Einar

2005-01-01

In this paper we examine within a partial equilibrium model for the oil market whether OPEC can combine high oil prices with a high market share. The oil market model explicitly accounts for reserves, development and production in 4 field categories across 13 regions. Oil companies may invest in new field development or alternatively on improved oil recovery in the decline phase of fields in production. Non-OPEC production is profit-driven, whereas OPEC meets the residual call for OPEC oil at a pre-specified oil price, while maintaining a surplus capacity. The model is run over a range of exogenous oil prices from 15 to 60 $ per barrel. Sustained high oil prices stimulate Non-OPEC production, but its remaining reserves gradually diminish despite new discoveries. Oil demand is only slightly affected by higher prices. Thus, OPEC is able to keep and eventually increase its current market share beyond 2010 even with oil prices around $30 per barrel. In fact, the model simulations indicate that an oil price around $40 is profitable for OPEC, even in the long term. Sensitivity analyses show that the most profitable price level for OPEC is generally above $35 per barrel. Even with several factors working jointly in OPEC's disfavour, the oil price seems to stick to the 30 $ level. Thus, for OPEC there is a trade-off between high prices and high market share in the short to medium term, but not in the long term. For OECD countries, on the other hand, there is a clear trade-off between low oil prices and low import dependence. (Author)

Spilled oil and infaunal activity - Modification of burrowing behavior and redistribution of oil

Science.gov (United States)

Clifton, H.E.; Kvenvolden, K.A.; Rapp, J.B.

1984-01-01

A series of experiments in Willapa Bay, Washington, indicates the degree to which the presence of spilled oil modifies the burrowing behavior of infauna and the extent to which the animals redistribute oil into intertidal sediment. Small amounts of North Slope crude oil introduced at low tide directly into burrow openings (mostly made by the crustacean Callianassa) resulted in a limited and temporary reduction in the number of burrow openings. In contrast, a layer of oil-saturated sand 1 cm thick buried about 5 cm below the sediment surface sharply reduced the number of burrow openings. After a year, the few new burrows penetrated only the margins of the experimental plot, and bioturbation below the buried oil-saturated sand layer declined dramatically. The experiments suggest that small amounts of oil temporarily stranded by tides in themselves have no long-range effect on burrowing behavior. The fauna, however, are capable of introducing measurable amounts of oil into the subsurface, where it is retained long after the rest of the stranded oil had washed away. A buried layer of oil-saturated sand greatly reduces infaunal activity; the oil presents an effective barrier that can persist for years. The oil incorporated into the sediment from burrow openings showed evidence of degradation after 7 months. In contrast the layer of buried oil remained essentially undergraded after a period of two years, even though oil in lower concentrations above the layer was degraded after a period of one year. This variation in degree of degradation of the buried oil, as well as the heterogeneity of oil distribution wherever the oil has been incorporated from the surface, emphasises the importance of careful sampling in any attempt to locate or monitor the presence of spilled oil in the substrate.In a series of experiments in Willapa Bay, Washington, small amounts of North Slope crude oil introduced at low tide directly into burrow openings resulted in a limited and temporary

Effect of ultrasonic intensity and frequency on oil/heavy-oil recovery from different wettability rocks

Energy Technology Data Exchange (ETDEWEB)

Naderi, K.; Babadagli, T. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Alberta Univ., Edmonton, AB (Canada)

2008-10-15

This study identified the mechanisms that are responsible for additional oil recovery that is often observed following an earthquake. It focused on the theory that harmonics of low frequency waves create high frequency waves as they penetrate into rock formations. A series of experiments were conducted on oil-wet rocks with high oil viscosities. The objective was to better understand how ultrasonic energy affects oil recovery at core and pore scale. Cylindrical sandstone cores were placed in imbibition cells to examine how the presence of initial water saturation can affect recovery, and how the recovery changes for different oil viscosities. An increase in oil recovery was observed with ultrasonic energy in all cases. The additional recovery with ultrasonic energy lessened as the oil viscosity increased. Ultrasonic intensity and frequency were shown to be critical to the performance, which is important since ultrasonic waves have limited penetration into porous medium. This is a key disadvantage for commercializing this promising process for well stimulation. Therefore, the authors designed a set-up to measure the ultrasonic energy penetration capacity in different media, notably air, water and slurry. The set-up could identify which types of reservoirs are most suitable for ultrasonic application. Imbibition experiments revealed that ultrasonic radiation increases recovery, and is much more significant in oil wet cases, where initial water saturation facilitate oil recovery. Higher frequency showed a higher rate of recovery compared to lower frequency, but the ultimate recovery was not changed substantially. 46 refs., 1 tab., 16 figs.

Shearing of saturated clays in rock joints at high confining pressures

International Nuclear Information System (INIS)

Wang, C.; Mao, N.

1979-01-01

Saturated clays are sheared between rock joints at various pore water pressures and at confining pressures up to 3 kb (300 Mpa). Sliding on these joints is stable. For a given clay, the shear stress required to initiate sliding increases linearly with the effective normal stress across the sliding surface, with a slope of 0.08 +- 0.01 for joints filled with saturated montmorillonite, 0.12 +- 0.01 with saturated chlorite, 0.15 +- 0.01 with saturated kaolinite, and 0.22 +- 0.02 with saturated silty illite. Thus at high confining pressures the shear stress required to initiate sliding on joints filled with saturated clays are very much smaller than that required to initiate sliding on clean rock joints or on joints filled with dry gouge materials. In the crust, saturation of gouge materials along active faults would greatly lower the frictional resistance to faulting and would stabilize fault movement. Different fault behaviors such as stable creep along some faults and intermittent but sudden slip along others may reflect in part different degrees of saturation of fault zones at depth

Environmental considerations in a high desert, crude oil pipeline spill

International Nuclear Information System (INIS)

Lowe, M.A.; Mancini, E.R.; Chamberlain, D.W.; Albright, G.R.

1993-01-01

A road grader punctured a high-pressure crude oil pipeline in the California high desert resulting in the release of approximately 4,200 barrels of Alaska North Slope crude oil. Oil sprayed over a steeply sloped hillside and flowed into an adjacent, densely vegetated ephemeral stream channel which carried secondary treatment sewage discharge. Three underflow dams were constructed in the channel within 2.8 km of the site. To ensure containment at the first dam, the sewage discharge was diverted from the channel, eventually to an upland impulse sprinkler irrigation system. Channel water and phase-separated ANS crude oil, impounded behind the first dam, percolated through alluvial sands/gravels to a depth of about five meters. The oil percolated through the soils on the receding surface of the water, affecting soils to an equivalent depth and saturating a horizontally narrow band of stream-bank soils as much as two to four meters into the bank. Stream channel undergrowth and a small number of mature trees were cleared to provide access for cleanup and/or to remove oiled plants. A large number of trees experienced partial leaf-drop within 25 days of the spill while two heavily oiled trees died. New vegetative growth was evident within five weeks of the spill. Site restoration included planting cuttings of five riparian tree species and hydroseeding exposed banks. Total petroleum hydrocarbon concentrations ranged from not detectable to 203,000 parts per million and averaged approximately 25,000 ppm in affected soils as sampled in place and in stockpiles. Approximately 30,000 tons of hydrocarbon-contaminated soil was excavated from the length of the stream channel (3,600 tons) as well as the area behind the first dam and spill site (26,400 tons). All soils were staged on site for waste profiling and final disposition. After treatment, the contaminated soil was beneficially reused as daily cover at a southern California landfill at a turnkey cost of approximately $57/ton

Increasing Waterflood Reserves in the Wilmington Oil Field through Improved Reservoir Characterization and Reservoir Management

Energy Technology Data Exchange (ETDEWEB)

Clarke, D.; Koerner, R.; Moos D.; Nguyen, J.; Phillips, C.; Tagbor, K.; Walker, S.

1999-04-05

This project used advanced reservoir characterization tools, including the pulsed acoustic cased-hole logging tool, geologic three-dimensional (3-D) modeling software, and commercially available reservoir management software to identify sands with remaining high oil saturation following waterflood. Production from the identified high oil saturated sands was stimulated by recompleting existing production and injection wells in these sands using conventional means as well as a short radius redrill candidate.

Saturated fatty acids, palm oil and cardiovascular health – where do we stand today?

Directory of Open Access Journals (Sweden)

Pramod Khosla

2014-12-01

Full Text Available For  almost  sixty years dietary fat  has  been  the  focal  point  for reducing the risk  from  coronary  heart  disease (CHD.  With  evidence  based  largely on  animal  and  observational  studies documenting that  saturated fatty acids (SFA  increase LDL-C (with the latter being associated with increased CHD risk, the notion that SFA increased CHD, became etched in folklore. As a consequence,   decreasing   SFA   to   <10%   of   total   calories,   became   the corner-stone   of   global   dietary recommendations. Ironically, the fact that SFA increased the large buoyant LDL particles (as opposed to small-dense atherogenic LDL particles, or that they increased the cardio-protective HDL-C and in some instances, lowered the atherogenic Lp(a, went largely unnoticed. However a spate of studies starting in 2009 has dramatically challenged our thinking on the “widely accepted” role of SFA.  Twenty year follow up data from prospective epidemiologic studies suggest that only two classes of fatty acids affect CHD risk, namely trans monounsaturated fatty acids (resulting principally from the partial hydrogenation of vegetable oils and polyunsaturated fatty acids (PUFA – which increase and decrease risk, respectively. These studies suggested that when  replacing/removing  SFA   from  the  diet,  the  replacement  nutrient  may  be  as important. Thus SFA replacement with PUFA may provide small benefits, but the replacement represents a dramatic shift in dietary regimen. The effects of replacing SFA with MUFA were inconclusive. If SFA are replaced with carbohydrates, then the quality of the carbohydrate (as measured by the glycemic index is also important. Earlier this year, a highly publicized study found no benefit on CHD even when SFA were replaced by PUFA, and questioned the usefulness of this public health message. The data on SFA has had a profound effect on the perceived role of

Crystallization of low saturated lipid blends of palm and canola oils with sorbitan monostearate and fully hydrogenated palm oil.

Science.gov (United States)

Barbosa, Karina Martins; Cardoso, Lisandro Pavie; Ribeiro, Ana Paula Badan; Kieckbusch, Theo Guenter; Buscato, Monise Helen Masuchi

2018-03-01

Several scientific investigations have focused on providing new strategies for supporting the development of low saturated and zero trans lipid materials, as healthier fat alternatives for food application. This work evaluated the consistency, crystallization behavior, microstructure and polymorphism of six blends composed of palm and canola oils at different concentrations (100:0, 80:20, 60:40, 40:60, 20:80 and 0:100, in w/w%) added with 5.0% of fully hydrogenated palm oil (FHPO) or with a mixture of 2.5% of FHPO and 2.5% of sorbitan monostearate (SMS). The results were compared with the non-structured blends (standard samples). Through microstructure images, the formation of a more homogeneous and denser packed crystal network was observed for samples added with both crystallization modifiers (FHPO/SMS) compared to the corresponding standard samples, after stabilization at 25 °C during 3 h. In particular, enhanced crystallization modifications were observed for the 40:60 blend, in which the crystal form β' emerged after the addition of FHPO/SMS. Moreover, the 40:60 blend structured with FHPO/SMS showed increased consistency (from 30 to 658 g F /cm 2 ) and induced onset crystallization in a higher temperature (from 13.1 to 23.9 °C) compared with the non-structured one, due to the specific crystallization effects provided by both added structurants.

Grinding temperature and energy ratio coe cient in MQL grinding of high-temperature nickel-base alloy by using di erent vegetable oils as base oil

Institute of Scientific and Technical Information of China (English)

Li Benkai; Li Changhe; Zhang Yanbin; Wang Yaogang; Jia Dongzhou; Yang Min

2016-01-01

Vegetable oil can be used as a base oil in minimal quantity of lubrication (MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force, and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grind-ing temperature, and energy ratio coefficient of MQL grinding were compared among the seven veg-etable oil types. Results revealed that (1) castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient;(2) palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient;(3) MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil;(4) viscosity significantly influences grinding force and grinding tem-perature to a greater extent than fatty acid varieties and contents in vegetable oils;(5) although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less vis-cous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature;(6) saturated fatty acid is a more efficient lubricant than unsaturated fatty acid;and (7) a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force, 87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7%energy ratio coefficient

CT-scan-monitored electrical resistivity measurements show problems achieving homogeneous saturation

International Nuclear Information System (INIS)

Sprunt, E.S.; Coles, M.E.; Davis, R.M.; Muegge, E.L.; Desai, K.P.

1991-01-01

X-ray CT scans obtained during measurement of the electrical resistivity of core samples revealed some problems in obtaining uniform saturation along the length of the sample. In this paper the electrical resistivity of core samples is measured as a function of water saturation to determine the saturation exponent, which is used in electric log interpretation. An assumption in such tests is that the water saturation is uniformly distributed. Failure of this assumption can result in errors in the determination of the saturation exponent. Three problems were identified in obtaining homogeneous water saturation in two samples of a Middle Eastern carbonate grainstone. A stationary front formed in one sample at 1 psi oil/brine capillary pressure. A moving front formed at oil/brine capillary pressures of 4 psi or less in both samples tested, in both a fresh mixed-wettability state and in a cleaned water-wet state. In these samples, the heterogeneous fluid distribution caused by a rapidly moving front did not dissipate when the capillary pressure was eliminated

Experimental study of heavy oil-water flow structure effects on relative permeabilities in a fracture filled with heavy oil

Energy Technology Data Exchange (ETDEWEB)

Shad, S.; Gates, I.D.; Maini, B.B. [Calgary Univ., AB (Canada). Dept. of Chemical and Petroleum Engineering]|[Alberta Ingenuity Centre for In Situ Energy, Edmonton, AB (Canada)

2008-10-15

An experimental apparatus was used to investigate the flow of water in the presence of heavy oil within a smooth-walled fracture. Different flow patterns were investigated under a variety of flow conditions. Results of the experiments were used to determine the accuracy of VC, Corey, and Shad and Gates models designed to represent the behaviour of oil wet systems. The relative permeability concept was used to describe the behaviour of multiple phases flowing through porous media. A smooth-walled plexiglass Hele-Shaw cell was used to visualize oil and water flow. Changes in flow rates led to different flow regimes. The experiment demonstrated that water flowed co-currently in the form of droplets or slugs. Decreases in the oil flow rate enlarged the size of the water droplets as well as the velocity, until eventually the droplets coalesced and became water slugs. Droplet appearance or disappearance directly impacted the oil and water saturation levels. Changes in fluid saturation altered the pressure gradient. Darcy's law for the 2 liquid phases were used to calculate relative permeability curves. The study showed that at low water saturation, oil relative permeability reached as high as 2.5, while water relative permeability was lower than unity. In the presence of a continuous water channel, water drops formed in oil, and the velocity of the drops was lower than their velocity under a discontinuous water flow regime. It was concluded that the Shad and Gates model overestimated oil relative permeability and underestimated water relative permeability. 38 refs., 2 tabs., 9 figs.

Exact expression for the effective acoustics of patchy-saturated rocks

NARCIS (Netherlands)

Vogelaar, B.; Smeulders, D.M.J.; Harris, J.

2010-01-01

Seismic effects of a partially gas-saturated subsurface have been known for many years. For example, patches of nonuniform saturation occur at the gas-oil and gas-water contacts in hydrocarbon reservoirs. Open-pore boundary conditions are applied to the quasi-static Biot equations of poroelasticity

Coconut oil and palm oil's role in nutrition, health and national ...

African Journals Online (AJOL)

Coconut and palm oils which were the major sources of dietary fats for centuries in most of West Africa have been branded as unhealthy highly saturated fats. Their consumption has been peddled to supposedly raise the level of blood cholesterol, thereby increasing the risk of coronary heart disease. This adverse view has ...

Virgin almond oil: Extraction methods and composition

Energy Technology Data Exchange (ETDEWEB)

Roncero, J.M.; Alvarez-Orti, M.; Pardo-Gimenez, A.; Gomez, R.; Rabadan, A.; Pardo, J.E.

2016-07-01

In this paper the extraction methods of virgin almond oil and its chemical composition are reviewed. The most common methods for obtaining oil are solvent extraction, extraction with supercritical fluids (CO2) and pressure systems (hydraulic and screw presses). The best industrial performance, but also the worst oil quality is achieved by using solvents. Oils obtained by this method cannot be considered virgin oils as they are obtained by chemical treatments. Supercritical fluid extraction results in higher quality oils but at a very high price. Extraction by pressing becomes the best option to achieve high quality oils at an affordable price. With regards chemical composition, almond oil is characterized by its low content in saturated fatty acids and the predominance of monounsaturated, especially oleic acid. Furthermore, almond oil contains antioxidants and fat-soluble bioactive compounds that make it an oil with interesting nutritional and cosmetic properties.

Virgin almond oil: Extraction methods and composition

International Nuclear Information System (INIS)

Roncero, J.M.; Alvarez-Orti, M.; Pardo-Gimenez, A.; Gomez, R.; Rabadan, A.; Pardo, J.E.

2016-01-01

In this paper the extraction methods of virgin almond oil and its chemical composition are reviewed. The most common methods for obtaining oil are solvent extraction, extraction with supercritical fluids (CO2) and pressure systems (hydraulic and screw presses). The best industrial performance, but also the worst oil quality is achieved by using solvents. Oils obtained by this method cannot be considered virgin oils as they are obtained by chemical treatments. Supercritical fluid extraction results in higher quality oils but at a very high price. Extraction by pressing becomes the best option to achieve high quality oils at an affordable price. With regards chemical composition, almond oil is characterized by its low content in saturated fatty acids and the predominance of monounsaturated, especially oleic acid. Furthermore, almond oil contains antioxidants and fat-soluble bioactive compounds that make it an oil with interesting nutritional and cosmetic properties.

Improvement of the deep desulphurization of diesel oil by pre-saturation and a recycle of the liquid phase

Energy Technology Data Exchange (ETDEWEB)

Datsevitch, L.; Jess, A.; Schmitz, C. [Bayreuth Univ. (Germany). Dept. of Chemical Engineering; Gudde, N.J. [BP Oil, Sunbury-on-Thames (United Kingdom). Refining Technology

2003-07-01

Within the next decade, the S-content both for gasoline and diesel oil will probably be set to a value of about 10 ppm. Desulfurization is usually obtained by hydrotreating (HDS) in a trickle bed reactor, i.e. in a three phase system with gaseous H{sub 2}, liquid oil (with dissolved H{sub 2}) and solid catalyst. The HDS-process has several problems, particularly if residual S-contents of less than 100 ppm are needed, because the remaining, refractory S-compounds like 4,6-dimethyldibenzothiophene are hard to convert. The amount of H{sub 2} fed to the reactor - after all in case of deep HDS - is much higher than the amount chemically needed and consumed by HDS. So the unconsumed H{sub 2} has to be recycled. As shown in this paper, the so-called presaturation concept using a two phase reactor (solid catalyst and oil externally pre-saturated with H{sub 2}) is an interesting alternative to the common trickle bed reactor. A recycle of H{sub 2} is not needed, and the reaction rate of HDS will higher or at least the same. (orig.)

High Amounts of n-Alkanes in the Composition of Asphodelus aestivus Brot. Flower Essential Oil from Cyprus.

Science.gov (United States)

Polatoğlu, Kaan; Demirci, Betül; Can Başer, Kemal Hüsnü

2016-10-01

There is only a couple of reports indicating essential oil composition of Asphodelus species in the literature. However, from the members of this genus many non-volatile secondary metabolites were isolated. In Cyprus, Asphodelus aestivus Brot. can be found abundantly in all regions of the island. This plant has various ethnobotanical uses in Cyprus. There is no report on the volatiles nor the essential oil composition of A. aestivus. The smell of A. aestivus flowers resembles that of a cat pee which caught our attention. Therefore, we have carried out GC, GC/MS analysis of the essential oil (yield: 0.01 v/w) obtained from Asphodelus aestivus flowers. Seventeen compounds were identified in the essential oil comprising 96.2% of the oil. The major components of the essential oil were hexadecanoic acid 35.6%, pentacosane 17.4%, tricosane 13.4% and heptacosane 8.4%. In our results, we expected to see sulfur containing cat pee odorants due to the odor of the flower whereas high amounts of n-alkanes, saturated fatty acids and minor amounts of acyclic diterpenes were observed.

Breakdown Characteristic Analysis of Paper- Oil Insulation under AC and DC Voltage

Science.gov (United States)

Anuar, N. F.; Jamail, N. A. M.; Rahman, R. A.; Kamarudin, M. S.

2017-08-01

This paper presents the study of breakdown characteristic of Kraft paper insulated with two different types of insulating fluid, which are Palm oil and Coconut oil. Palm oil and Coconut oil are chosen as the alternative fluid to the transformer oil because it has high potential and environmentally-friendly. The Segezha Kraft papers with various thicknesses (65.5 gsm, 75 gsm, 85gsm, 90 gsm) have been used in this research. High Voltage Direct Current (HVDC), High Voltage Alternating Current (HVAC) and carbon track and severity analysis is conducted to observe the sample of aging Kraft paper. These samples have been immersed using Palm oil and Coconut oil up to 90 days to observe the absorption rate. All samples started to reach saturation level at 70 days of immersion. HVDC and HVAC breakdown experiments have been done after the samples had reached the saturation level based on normal condition, immersed in Palm oil and immersed in Coconut oil. All samples immersed in liquid show different breakdown voltage reading compared to normal condition. The analysis of carbon track and severity on surface has been done using Analytical Scanning Electron Microscope (SEM) Analysis. The results of the experiment show that the sample of Kraft paper immersed in Palm oil was better than Coconut oil immersed sample. Therefore the sample condition was the main factor that determines the value of breakdown voltage test. Introduction

An Estimate of Recoverable Heavy Oil Resources of the Orinoco Oil Belt, Venezuela

Science.gov (United States)

Schenk, Christopher J.; Cook, Troy A.; Charpentier, Ronald R.; Pollastro, Richard M.; Klett, Timothy R.; Tennyson, Marilyn E.; Kirschbaum, Mark A.; Brownfield, Michael E.; Pitman, Janet K.

2009-01-01

The Orinoco Oil Belt Assessment Unit of the La Luna-Quercual Total Petroleum System encompasses approximately 50,000 km2 of the East Venezuela Basin Province that is underlain by more than 1 trillion barrels of heavy oil-in-place. As part of a program directed at estimating the technically recoverable oil and gas resources of priority petroleum basins worldwide, the U.S. Geological Survey estimated the recoverable oil resources of the Orinoco Oil Belt Assessment Unit. This estimate relied mainly on published geologic and engineering data for reservoirs (net oil-saturated sandstone thickness and extent), petrophysical properties (porosity, water saturation, and formation volume factors), recovery factors determined by pilot projects, and estimates of volumes of oil-in-place. The U.S. Geological Survey estimated a mean volume of 513 billion barrels of technically recoverable heavy oil in the Orinoco Oil Belt Assessment Unit of the East Venezuela Basin Province; the range is 380 to 652 billion barrels. The Orinoco Oil Belt Assessment Unit thus contains one of the largest recoverable oil accumulations in the world.

[Effects of vegetal oil supplementation on the lipid profile of Wistar rats ].

Science.gov (United States)

Poveda, Elpidia; Ayala, Paola; Milena, Rodríguez; Ordóñez, Edgar; Baracaldo, Cesar; Delgado, Willman; Guerra, Martha

2005-03-01

Dietary tocopherols, tocotrienols and saturated, mono and polyunsaturated fatty acids have been reported to have an effect on blood lipid profiles. In Colombia, vegetable oils (palm, soy, corn, sunflower, and canola) are a common dietary constituent and consumed in high quantities. In the current study, the effects of vegetable oil consumption was examined by measuring blood concentrations of triglycerides (TG), total cholesterol (TC) and HDL cholesterol (HDL-C) in male Wistar rats. The concentrations of tocopherols, tocotrienols, and fatty acids in each oil was quantified by High Performance Liquid Chromatography (HPLC). Each rat diet was supplemented with 0.2 ml/day with one oil type. Over a 4-week period, groups of animals were sacrificed weekly and blood samples were obtained to quantify TC, TG and HDL-C for each oil class. Statistical analyses included mean, standard deviation, ANOVA and Bonferroni comparisons tests. Triglyceride content was not affected except in the control and the soy group in the third treatment week, although a tendency for decreased TG was noted in the palm oil group and for increased TG in the sunflower oil and canola oil groups. No significant differences in total cholesterol were observed. In HDL-C, significant differences were present for every treatment week (p = 0.005); this represented a decreasing trend in palm oil group and an increasing trend in the sunflower and corn oil groups. The oils effected changes in the blood lipid profile. A small amount of saturated fatty acids (tocopherol and tocotrienol) were favourable for the HDL-C increase. The presenct of tocorienols tended to decrease the TG and probably helped attenuate the unfavorable effects of the saturated fatty acids.

Structural level characterization of base oils using advanced analytical techniques

KAUST Repository

Hourani, Nadim

2015-05-21

Base oils, blended for finished lubricant formulations, are classified by the American Petroleum Institute into five groups, viz., groups I-V. Groups I-III consist of petroleum based hydrocarbons whereas groups IV and V are made of synthetic polymers. In the present study, five base oil samples belonging to groups I and III were extensively characterized using high performance liquid chromatography (HPLC), comprehensive two-dimensional gas chromatography (GC×GC), and Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS) equipped with atmospheric pressure chemical ionization (APCI) and atmospheric pressure photoionization (APPI) sources. First, the capabilities and limitations of each analytical technique were evaluated, and then the availed information was combined to reveal compositional details on the base oil samples studied. HPLC showed the overwhelming presence of saturated over aromatic compounds in all five base oils. A similar trend was further corroborated using GC×GC, which yielded semiquantitative information on the compound classes present in the samples and provided further details on the carbon number distributions within these classes. In addition to chromatography methods, FT-ICR MS supplemented the compositional information on the base oil samples by resolving the aromatics compounds into alkyl- and naphtheno-subtituted families. APCI proved more effective for the ionization of the highly saturated base oil components compared to APPI. Furthermore, for the detailed information on hydrocarbon molecules FT-ICR MS revealed the presence of saturated and aromatic sulfur species in all base oil samples. The results presented herein offer a unique perspective into the detailed molecular structure of base oils typically used to formulate lubricants. © 2015 American Chemical Society.

Low-cost but accurate radioactive logging for determining gas saturation in a reservior

International Nuclear Information System (INIS)

Neuman, C.H.

1976-01-01

A method is disclosed for determining gas saturation in a petroleum reservoir using logging signals indirectly related to the abundances of oxygen and carbon nuclei in the reservoir rock. The first step of the invention is to record first and second logs sensitive to the abundance of oxygen and carbon nuclei, respectively, after the region surrounding the well bore is caused to have fluid saturations representative of the bulk of the reservoir. A purposeful change is then made in the fluid saturations in the region surrounding the well bore by injecting a liquid capable of displacing substantially all of the original fluids. The logs are recorded a second time. The displacing fluid is then itself displaced by brine, and a third suite of logs is recorded. The total fluid and oil saturations are then determined from the differences between respective corresponding logs and from known fractional volume oxygen and carbon contents of the reservoir brine and oil and the first injected liquid. Gas saturation is then calculated from differences between total fluid and oil saturation values. It is not necessary that the log responses be independent of the material in the borehole, the casing, the casing cement, or the reservoir rock. It is only necessary that changes in formation fluids content cause proportional changes in log responses. 7 Claims, 4 Figures

Development and utilization of sunflower genotypes with altered oil quality

OpenAIRE

Cvejić, Sandra; Jocić, Siniša; Miladinović, Dragana; Jocković, Milan; Imerovski, Ivana; Sakač, Zvonimir; Miklič, Vladimir

2014-01-01

Sunflower oil is among the highest quality oils of plant origin. The oil of standard sunflowers has an average of 10% saturated fatty acids, 20-30% oleic acid and 60-70% linoleic acid. The total content of tocopherols in standard sunflower oil is 700-1000 mg/kg with the predominant being alpha-tocopherol (vitamin-E). Following the trends of the food and non-food industries sunflower breeders have been able to significantly change the fatty acid composition of the oil. The oil of high-oleic hy...

Experimental study and mechanical modelling of the effects of water-driving in an oil saturated chalk. Application to the petroleum industry; Etude experimentale et modelisation mecanique des effets du balayage a l'eau dans une craie saturee d'huile. Application a l'industrie petroliere

Energy Technology Data Exchange (ETDEWEB)

Mata, C.

2001-01-01

The production of hydrocarbons may sometimes lead to compaction of the oil-reservoir layers with substantial collapse of the soil surface; this mechanism is usually mentioned as Subsidence. Classical remedy to this problem is to sustain the fluid pressure with the help of water injection. However, in presence of high porosity chalk (porosity > 30%), this technique does not give effective results: the subsidence rate at North Sea reservoirs (Ekofisk field), after injection, has remained unchanged. Some justify the subsistence in the chalk as caused by phenomena of dissolution of the carbonates; others think it is connected to the destruction of capillary menisci. In this research, we follow this second approach. This study is finalized to a better understanding of the compaction mechanisms in pure carbonates when water is injected. This is done by proposing -in micro-scale first and in macro-scale after- a physical model that agrees with empirical observations. In order to meet this target, IFP skills and experience in physical and chemical measurements (taken before, after and during mechanical tests) have proficiently joined ENPC laboratory (CERMMO) knowledge of micro and macro modelling. The soft rock studied is a Paris basin's white chalk (Craie de Guerville). Its physical and chemical characterisation (i.e.: silica content, porosity, permeability) is very similar to North Sea chalk, but Guerville chalk has never been in contact with oil and generally it crops out of the ground surface. Strength parameters of this rock have been first determined by standard triaxial tests. Three different saturation configurations have been examined: dry, fully oil-saturated and fully water-saturated. As literature clearly state, dry chalk is stronger than oil saturated chalk and the first two are largely stronger than water saturated chalk. Therefore uniaxial strain water injection tests have been performed on oil saturated samples. Results, coupled with previous physical

Oil supply and demand

International Nuclear Information System (INIS)

Rech, O.

2006-01-01

The year 2004 saw a change in the oil market paradigm that was confirmed in 2005. Despite a calmer geopolitical context, prices continued to rise vigorously. Driven by world demand, they remain high as a result of the saturation of production and refining capacity. The market is still seeking its new equilibrium. (author)

Oil supply and demand

Energy Technology Data Exchange (ETDEWEB)

Rech, O

2006-07-01

The year 2004 saw a change in the oil market paradigm that was confirmed in 2005. Despite a calmer geopolitical context, prices continued to rise vigorously. Driven by world demand, they remain high as a result of the saturation of production and refining capacity. The market is still seeking its new equilibrium. (author)

Saturated fat stimulates obesity and hepatic steatosis and affects gut microbiota composition by an enhanced overflow of dietary fat to the distal intestine

NARCIS (Netherlands)

Wit, de N.J.W.; Derrien, M.; Bosch-Vermeulen, H.; Oosterink, E.; Keshtkar, S.; Duval, C.N.C.; Vogel-van den Bosch, de H.M.; Kleerebezem, M.; Muller, M.R.; Meer, van der R.

2012-01-01

We studied the effect of dietary fat type, varying in polyunsaturated-to-saturated fatty acid ratios (P/S), on development of metabolic syndrome. C57Bl/6J mice were fed purified high-fat diets (45E% fat) containing palm oil (HF-PO; P/S 0.4), olive oil (HF-OO; P/S 1.1), or safflower oil (HF-SO; P/S

Saturated fat stimulates obesity and hepatic steatosis and affects gut microbiota composition by an enhanced overflow of dietary fat to the distal intestine

NARCIS (Netherlands)

Wit, de Nicole; Oosterink, Els; Bosch-Vermeulen, Hanneke; Keshtkar, Shohreh; Duval, C.N.C.; Vogel-van den Bosch, de Johan; Muller, Michael; Meer, van der Roelof

2012-01-01

We studied the effect of dietary fat type, varying in polyunsaturated/saturated fatty acid ratio's (P/S) on development of metabolic syndrome. C57Bl/6J mice were fed purified high-fat diets (45E% fat) containing palm oil (HF-PO; P/S 0.4), olive oil (HF-OO; P/S 1.1) or safflower oil (HF-SO; P/S 7.8)

Dispersed free phytosterols as structuring agents in lipid systems with reduced saturated fat

International Nuclear Information System (INIS)

Godoi, K.R.R.; Basso, R.C.; Buscato, M.H.M.; Cardoso, L.P.; Kieckbusch, T.G.; Ribeiro, A.P.B.

2017-01-01

The negative effects of trans fatty acids and saturated fatty acids in food have been widely discussed and this has led to progressive changes in the legislation of many countries. The use of structuring agents or crystallization modifiers, as specific triacylglycerol and minor lipids have been indicated as the only viable alternative for obtaining low saturated fats with properties which are compatible with food application. In this context, phytosterols, natural products with hypocholesterolemic action, and hard fat-crystallization modulators, present a new option for structuring lipid matrices. This work characterized the effects of fully hydrogenated soybean oil and free phytosterols on the physical properties and crystallization behavior of palm oil and canola oil blends for the development of zero trans-fat bases with low levels of saturated fatty acids. The systems were evaluated for chemical composition, atherogenic index, solid fat profiles, microstructure, consistency, thermal behavior and polymorphism. [es

A Comparative Study on Formation of Polar Components, Fatty Acids and Sterols during Frying of Refined Olive Pomace Oil Pure and Its Blend Coconut Oil.

Science.gov (United States)

Ben Hammouda, Ibtissem; Triki, Mehdi; Matthäus, Bertrand; Bouaziz, Mohamed

2018-04-04

The frying performance of pure refined olive-pomace oil (ROPO) and blended with refined coconut oil (RCO) (80:20) was compared during a frying operation of French fries at 180 °C. Blending polyunsaturated oils with highly saturated or monounsaturated oils has been studied extensively, however in literature there is no study has been reported so far on blending ROPO (rich in monounsaturated fatty acids) with RCO (rich in saturated fatty acids) to formulate new frying oils. At the end of the frying process, the blend of ROPO/RCO exhibited a higher chemical stability than the pure ROPO based on total polar compounds (TPC), and polymers. The rate of TPC formation was achieved 23.3% and 30.6% for the blend and the pure oil, respectively. Trans and free fatty acids content, as well as anisidine value were also observed to be the highest in the pure ROPO. This study evaluated the frying performance in the search for appropriate frying oils to deliver healthy fried products with optimized nutritional qualities.

Constituents of essential oil from the dried fruits and stems of Akebia quinata (THUNB.) DECNE.

Science.gov (United States)

Kawata, Jyunichi; Kameda, Munekazu; Miyazawa, Mitsuo

2007-01-01

The compositions of the essential oil from AKEBIAE FRUCTUS and AKEBIAE CAULIS, the dried fruits and stems of Akebia quinata (THUNB.) DECNE. (Lardizabalaceae), have been investigated by GC and GC/MS. As a result, the fruits oil was revealed the presence of 86 components, representing 98.4% of the total oil. The major compounds of the fruits oil were limonene, eugenol, octanal and p-cymene. The monoterpenoids and saturated short-chain aldehyde (C6 approximately C10) were main volatile fractions of the oil. Ninety components accounting for 90.5% of constituents of stems oil were identified, and the main compounds of the oil were hexanoic acid, palmitic acid, (2E, 4E)-decadienal and hexanol. The oil had high content of saturated fatty acids (C6 approximately C16), and unsaturated short-chain aldehyde (C6 approximately C10).

Modelling the behavior of an oil saturated sand

International Nuclear Information System (INIS)

Evgin, E.; Altaee, A.; Lord, S.; Konuk, I.

1990-01-01

The experiments carried out in an earlier study show the oil contamination affects the strength and deformation characteristics of a crushed quartz sand. In the present study, a mathematical soil model is used to simulate the mechanical behavior of the same sand. The model parameters are determined for both clean and oil contaminated soil. Simulations are made for the stress-strain behavior of the soil in drained and undrained conventional traixial compression tests. In order to illustrate the effect of changes in the soil properties on the behavior of an engineering structure, a finite element analysis is carried out. In this paper comparative results are presented to show the differences in the behavior of a foundation resting on a clean sand, on an oil contaminated sand, and on a sand contaminated locally

Changes in the composition and properties of Ashalchinskoye bitumen-saturated sandstones when exposed to water vapor

Science.gov (United States)

Korolev, E.; Eskin, A.; Kolchugin, A.; Morozov, V.; Khramchenkov, M.; Gabdelvalieva, R.

2018-05-01

Ashalchinskoye bitumen deposit is an experimental platform for testing technology of high-viscosity oil extraction from reservoir rocks. Last time for enhanced of oil recovery in reservoir used pressurization a water vapor with a temperature of ∼ 180 ° C (SAGD technology). However, what happens in sandstone reservoir is little known. We did a study of the effects of water vapor on the structural components of bitumen saturated sandstone. In paper were studied the rock samples at base condition and after one week exposure by water vapour. The thermal analysis showed that steaming helps to removes light and middle oil fractions with a boiling point up to 360 ° C from oil saturated sandstones. Content of heavy oil fractions virtually unchanged. Studying the composition of water extractions of samples showed that the process of aquathermolysis of oil is accompanied by a lowering of the pH of the pore solution from 7.4 to 6.5 and rise content in several times of mobile cations Ca2+, Mg2+ and HCO3 -, SO4 2- anions. Follows from this that the thermal steam effect by bitumen saturated sandstones leads to partial oxidation of hydrocarbons with to form a carbon dioxide. The source of sulfate ions were oxidized pyrite aggregates. Due to the increasing acidity of condensed water, which fills the pore space of samples, pore fluid becomes aggressive to calcite and dolomite cement of bitumen saturated sandstones. As a result of the dissolution of carbonate cement the pore fluid enriched by calcium and magnesium cations. Clearly, that the process is accompanied by reduction of contact strength between fragments of minerals and rocks. Resulting part of compounds is separated from the outer side of samples and falls to bottom of water vapor container. Decreasing the amount of calcite and dolomite anions in samples in a steam-treated influence is confirmed by X-Ray analysis. X-Ray analysis data of study adscititious component of rocks showed that when influenced of water vapor to

Oil goldenberry (Physalis peruviana L.).

Science.gov (United States)

Ramadan, Mohamed F; Mörsel, Jörg-T

2003-02-12

Whole berries, seeds, and pulp/peel of goldenberry (Physalis peruviana L.) were compared in terms of fatty acids, lipid classes, triacylglyerols, phytosterols, fat-soluble vitamins, and beta-carotene. The total lipid contents in the whole berries, seeds, and seedless parts were 2.0, 1.8, and 0.2% (on a fresh weight basis), respectively. Linoleic acid was the dominating fatty acid followed by oleic acid as the second major fatty acid. Palmitic and stearic acids were the major saturates. In pulp/peel oil, the fatty acid profile was characterized by higher amounts of saturates, monoenes, and trienes than in whole berry and seed oils. Neutral lipids comprised >95% of total lipids in whole berry oil and seed oil, while neutral lipids separated in lower level in pulp/peel oil. Triacylglycerols were the predominant neutral lipid subclass and constituted ca. 81.6, 86.6, and 65.1% of total neutral lipids in whole berry, seed, and pulp/peel oils, respectively. Nine triacylglycerol molecular species were detected, wherein three species, C54:3, C52:2, and C54:6, were presented to the extent of approximately 91% or above. The highest level of phytosterols was estimated in pulp/peel oil that contained the highest level of unsaponifiables. In both whole berry and seed oils, campesterol and beta-sitosterol were the sterol markers, whereas Delta5-avenasterol and campesterol were the main 4-desmethylsterols in pulp/peel oil. The tocopherols level was much higher in pulp/peel oil than in whole berry and seed oils. beta- and gamma-tocopherols were the major components in whole berry and seed oils, whereas gamma- and alpha-tocopherols were the main constituents in pulp/peel oil. beta-Carotene and vitamin K(1) were also measured in markedly high levels in pulp/peel oil followed by whole berry oil and seed oil, respectively. Information provided by the present work is of importance for further chemical investigation of goldenberry oil and industrial utilization of the berries as a raw

A 70 kV solid-state high voltage pulse generator based on saturable pulse transformer.

Science.gov (United States)

Fan, Xuliang; Liu, Jinliang

2014-02-01

High voltage pulse generators are widely applied in many fields. In recent years, solid-state and operating at repetitive mode are the most important developing trends of high voltage pulse generators. A solid-state high voltage pulse generator based on saturable pulse transformer is proposed in this paper. The proposed generator is consisted of three parts. They are charging system, triggering system, and the major loop. Saturable pulse transformer is the key component of the whole generator, which acts as a step-up transformer and main switch during working process of this generator. The circuit and working principles of the proposed pulse generator are introduced first in this paper, and the saturable pulse transformer used in this generator is introduced in detail. Circuit of the major loop is simulated to verify the design of the system. Demonstration experiments are carried out, and the results show that when the primary energy storage capacitor is charged to a high voltage, such as 2.5 kV, a voltage with amplitude of 86 kV can be achieved on the secondary winding. The magnetic core of saturable pulse transformer is saturated deeply and the saturable inductance of the secondary windings is very small. The switch function of the saturable pulse transformer can be realized ideally. Therefore, a 71 kV output voltage pulse is formed on the load. Moreover, the magnetic core of the saturable pulse transformer can be reset automatically.

Impact of gain saturation on the mode instability threshold in high-power fiber amplifiers

DEFF Research Database (Denmark)

Hansen, Kristian Rymann; Lægsgaard, Jesper

2014-01-01

We present a coupled-mode model of transverse mode instability in high-power fiber amplifiers, which takes the effect of gain saturation into account. The model provides simple semi-analytical formulas for the mode instability threshold, which are valid also for highly saturated amplifiers...

Comparison of Atmospheric Pressure Chemical Ionization and Field Ionization Mass Spectrometry for the Analysis of Large Saturated Hydrocarbons.

Science.gov (United States)

Jin, Chunfen; Viidanoja, Jyrki; Li, Mingzhe; Zhang, Yuyang; Ikonen, Elias; Root, Andrew; Romanczyk, Mark; Manheim, Jeremy; Dziekonski, Eric; Kenttämaa, Hilkka I

2016-11-01

Direct infusion atmospheric pressure chemical ionization mass spectrometry (APCI-MS) was compared to field ionization mass spectrometry (FI-MS) for the determination of hydrocarbon class distributions in lubricant base oils. When positive ion mode APCI with oxygen as the ion source gas was employed to ionize saturated hydrocarbon model compounds (M) in hexane, only stable [M - H] + ions were produced. Ion-molecule reaction studies performed in a linear quadrupole ion trap suggested that fragment ions of ionized hexane can ionize saturated hydrocarbons via hydride abstraction with minimal fragmentation. Hence, APCI-MS shows potential as an alternative of FI-MS in lubricant base oil analysis. Indeed, the APCI-MS method gave similar average molecular weights and hydrocarbon class distributions as FI-MS for three lubricant base oils. However, the reproducibility of APCI-MS method was found to be substantially better than for FI-MS. The paraffinic content determined using the APCI-MS and FI-MS methods for the base oils was similar. The average number of carbons in paraffinic chains followed the same increasing trend from low viscosity to high viscosity base oils for the two methods.

High or low oxygen saturation and severe retinopathy of prematurity: a meta-analysis.

Science.gov (United States)

Chen, Minghua L; Guo, Lei; Smith, Lois E H; Dammann, Christiane E L; Dammann, Olaf

2010-06-01

Low oxygen saturation appears to decrease the risk of severe retinopathy of prematurity (ROP) in preterm newborns when administered during the first few weeks after birth. High oxygen saturation seems to reduce the risk at later postmenstrual ages (PMAs). However, previous clinical studies are not conclusive individually. To perform a systematic review and meta-analysis to report the association between severe ROP incidence of premature infants with high or low target oxygen saturation measured by pulse oximetry. Studies were identified through PubMed and Embase literature searches through May 2009 by using the terms "retinopathy of prematurity and oxygen" or "retinopathy of prematurity and oxygen therapy." We selected 10 publications addressing the association between severe ROP and target oxygen saturation measured by pulse oximetry. Using a random-effects model we calculated the summary-effect estimate. We visually inspected funnel plots to examine possible publication bias. Low oxygen saturation (70%-96%) in the first several postnatal weeks was associated with a reduced risk of severe ROP (risk ratio [RR]: 0.48 [95% confidence interval (CI): 0.31-0.75]). High oxygen saturation (94%-99%) at > or = 32 weeks' PMA was associated with a decreased risk for progression to severe ROP (RR: 0.54 [95% CI: 0.35-0.82]). Among preterm infants with a gestational age of large randomized clinical trial with long-term developmental follow-up is warranted to confirm this meta-analytic result.

Discarded seeds from red pepper (Capsicum annum) processing industry as a sustainable source of high added-value compounds and edible oil.

Science.gov (United States)

Azabou, Samia; Taheur, Fadia Ben; Jridi, Mourad; Bouaziz, Mohamed; Nasri, Moncef

2017-10-01

The chemical composition and the antioxidant properties of Capsicum annum discarded seeds from processing industry with their corresponding extracted oil were investigated. C. annum seeds had high levels of crude proteins (18.30%), crude oil (11.04%), and dietary fibers (60.96%). The lipophilic fraction of C. annum seeds showed higher radical scavenging activity compared to their hydrophilic fraction, while this latter exhibited the highest reducing power. The results of fatty acid composition showed that fatty acids present in C. annum seed oil were mainly polyunsaturated (84.23%), with linoleic acid being the major polyunsaturated fatty acid (70.93%). The major monounsaturated fatty acid was oleic acid (12.18%), while the main saturated fatty acid was palmitic acid (11.90%). C. annum seed oil showed high absorbance in the UV-B, UV-A, and visible ranges. Owing to their composition, C. annum seeds discarded from pepper processing industry as by-product could be potentially used as high added-value ingredients in some food or nutraceutical formulations because they are well endowed with essential nutriments required for human health.

How bioavailable is highly weathered Deepwater Horizon oil?

Science.gov (United States)

Bostic, J.; Ziolkowski, L. A.; Reddy, C. M.; Aeppli, C.; Swarthout, B.

2016-02-01

Oiled sand patties continue to be deposited on northern Gulf of Mexico beaches five years after the Deepwater Horizon (DwH) oil spill. It is known that during the first 18 months post-spill, sand patties from DwH were chemically transformed, both biotically and abiotically, from wellhead release to beach deposition. However, the chemically transformed oil, which appears to become more polar over time, is not well understood in regards to its biodegradation potential. Biodegradation exerts a large control on the fate of spilled oil, representing a major conduit for its removal from the environment. To assess the bioavailability of this weathered oil, sand patties were collected from intertidal and supratidal zones of beaches in Florida, Alabama, and Mississippi in July 2015. Microbial biomarkers of the viable community, phospholipid fatty acids (PLFA), were detected on all samples collected. The PLFA distributions (mostly saturated and branched structures) and abundances (2 - 9 x 1013 cells/g sand patty) were similar across sampling locations. The positive correlation between PLFA abundance and surface area to volume ratios of sand patties indicates that microbes are preferentially inhabiting outside surfaces of the patties. We will present data on the radiocarbon (14C) content of PLFA to assess carbon (C) sources assimilated by microbes. 14C of PLFA is a powerful tool for assessing C sources assimilated in this setting. Oil has no 14C (Δ14C= -1000‰) while modern organic matter has relatively abundant 14C (Δ14C= 0‰). Fingerprinting analysis of biomarker ratios using comprehensive two-dimensional gas chromatography will be presented to ascertain if oil originated from DwH. The extent of the chemical transformation of the oil into more polar compounds will also be measured using thin layer chromatography. Results of this investigation aim to determine the bioavailability and ultimate fate of oiled sand patties that continue to wash ashore on Gulf of Mexico

Diet-induced thermogenesis is lower in rats fed a lard diet than in those fed a high oleic acid safflower oil diet, a safflower oil diet or a linseed oil diet.

Science.gov (United States)

Takeuchi, H; Matsuo, T; Tokuyama, K; Shimomura, Y; Suzuki, M

1995-04-01

The objectives of the present study were to examine the effects of dietary fats differing in fatty acid composition on diet-induced thermogenesis, sympathetic activity in brown adipose tissue and body fat accumulation in rats. Rats were meal-fed for 12 wk an isoenergetic diet based on lard, high oleic acid safflower oil, safflower oil or linseed oil, and norepinephrine turnover rates in brown adipose tissue were then estimated. Whole-body oxygen consumption after the meal indicated that diet-induced thermogenesis was significantly lower in rats fed the lard diet than in those fed the other diets. The norepinephrine turnover rate in the interscapular brown adipose tissue was also significantly lower in the lard diet group than in the other diet groups. The carcass fat content was significantly higher in the lard diet group than in the other diet groups, whereas the abdominal adipose tissue weights were the same in all diet groups. These results suggest that the intake of animal fats rich in saturated fatty acids, compared with the intake of vegetable oils rich in monounsaturated or polyunsaturated fatty acids, decreases diet-induced thermogenesis by a decline of sympathetic activity in brown adipose tissue, resulting in the promotion of body fat accumulation.

Aromatics saturation, opening and cleavage technology for middle distillates

Energy Technology Data Exchange (ETDEWEB)

Oballa, M.C.; Simanzhenkov, V.; Kim, G. [NOVA Chemicals Corp., Calgary, AB (Canada)

2009-07-01

In order to address environmental concerns, there is a need to develop technologies to reformulate or adjust the quality of transportation fuels. The purpose is to reduce the concentration of the compounds which negatively affect the air that people breathe. One of those targeted is the aromatics content of diesel, because high aromatics content results in low cetane number of diesel, as well as higher emission of particulate matter. Less conventional sources of hydrocarbon feedstock such as oil from oil sands and/or shale oil are being exploited in Alberta. These feeds contain multiple fused aromatic ring compounds. NOVA Chemicals would like to use these potentially abundant liquids as feed, but they must first be transformed into a more user friendly state. This paper discussed the development of a process technology that could saturate the aromatic rings, open up the saturated rings and cleave them to get smaller paraffinic molecules. The products then comprised of lower paraffins are suitable as feed to steam crackers for the production of ethylene and propylene, higher paraffins suitable for blending into gasoline and mono aromatic ring compounds which may be further treated through alkylation of benzene to ethylbenzene and dealkylation to styrene. The paper discussed the process steps and highlighted the catalysts. Research results were also shown. It was concluded that the critical technology gaps, as well as solutions, which would enable overcoming the challenges related to handling of aromatic bitumen feedstock, entail the development of two different catalysts, which are on two different technology platforms. 7 refs., 3 tabs., 5 figs.

Impact of Endogenous Phenolics in Canola Oil on the Oxidative Stability of Oil-in-Water Emulsions

DEFF Research Database (Denmark)

Sørensen, Ann-Dorit Moltke; Friel, James; Moser, Jill

canola seeds. Fractionated extracts of Sinapic acid, Sinapine and Canolol was used as well as a non fractionated extract. These extracts was added (100 and 350 μM) to 10% o/w emulsion with stripped canola oil in order to evaluate their effect on lipid oxidation in emulsions. For comparison......Canola oil is low in saturated fat, high in monounsaturated fat and has a favourable omega-6:omega-3 ratio . Therefore, Canola oil has a healthier fatty acid profile compared to other plant oils such as soy oil. Therefore, canola oil is also an ingredient in many food products. However, the content...... of unsaturated lipid makes canola oil susceptible towards lipid oxidation. Many food products are lipid containing emulsions and a lot of efforts have been put into developing methods to protect the lipids against oxidation. Since lipid oxidation has a negative influence on the shelf life of the foods, efficient...

Method for enhanced oil recovery

Science.gov (United States)

Comberiati, Joseph R.; Locke, Charles D.; Kamath, Krishna I.

1980-01-01

The present invention is directed to an improved method for enhanced recovery of oil from relatively "cold" reservoirs by carbon dioxide flooding. In oil reservoirs at a temperature less than the critical temperature of 87.7.degree. F. and at a pore pressure greater than the saturation pressure of carbon dioxide at the temperature of the reservoir, the carbon dioxide remains in the liquid state which does not satisfactorily mix with the oil. However, applicants have found that carbon dioxide can be vaporized in situ in the reservoir by selectively reducing the pore pressure in the reservoir to a value less than the particular saturated vapor pressure so as to greatly enhance the mixing of the carbon dioxide with the oil.

Use of imaging plates at near saturation for high energy density particles

International Nuclear Information System (INIS)

Tanimoto, Tsuyoshi; Ohta, Kazuhide; Habara, Hideaki; Kodama, Ryousuke; Tanaka, Kazuo A.; Yabuuchi, Toshinori; Tampo, Motonobu; Zheng Jian

2008-01-01

Since an imaging plate (IP) is sensitive to electron, ion, and x rays, it can be used as a detector for laser plasma experiment using ultraintense laser. Moreover, an IP has the advantageous features such as high sensitivity, wide dynamic range, and high spatial resolution. Even though IP itself has a considerable wide dynamic range up to 10 5 , the IP data have appeared often saturated at an IP reading device. We propose a reading technique by inserting optical density filters so that an apparently saturated IP data can be saved.

A combined high-sugar and high-saturated-fat dietary pattern is associated with more depressive symptoms in a multi-ethnic population

NARCIS (Netherlands)

Vermeulen, Esther; Stronks, Karien; Snijder, Marieke B.; Schene, Aart H.; Lok, Anja; Vries, de Jeanne H.; Visser, Marjolein; Brouwer, Ingeborg A.; Nicolaou, Mary

2017-01-01

Objective: To identify a high-sugar (HS) dietary pattern, a high-saturated-fat (HF) dietary pattern and a combined high-sugar and high-saturated-fat (HSHF) dietary pattern and to explore if these dietary patterns are associated with depressive symptoms. Design: We used data from the HELIUS (Healthy

Amazonian Buriti oil: chemical characterization and antioxidant potential

Energy Technology Data Exchange (ETDEWEB)

Speranza, P.; Oliveira Falcao, A. de; Alves Macedo, J.; Silva, L.H.M. da; Rodrigues, A.M. da C.; Alves Macedo, G.

2016-07-01

Buriti oil is an example of an Amazonian palm oil of economic importance. The local population uses this oil for the prevention and treatment of different diseases; however, there are few studies in the literature that evaluate its properties. In this study, detailed chemical and antioxidant properties of Buriti oil were determined. The predominant fatty acid was oleic acid (65.6%) and the main triacylglycerol classes were tri-unsaturated (50.0%) and di-unsaturated-mono-saturated(39.3%) triacylglycerols. The positional distribution of the classes of fatty acids on the triacylglycerol backbone indicated a saturated and unsaturated fatty acid relationship similar in the three-triacylglycerol positions. All tocopherol isomers were present, with a total content of 2364.1 mg·kg−1. α-tocopherol constitutes 48% of the total tocopherol content, followed by γ- tocopherol (45%). Total phenolic (107.0 mg gallic acid equivalent·g−1 oil) and β-carotene (781.6 mg·kg−1) were particularly high in this oil. The highest antioxidant activity against the free radical 1,1-diphenyl-2-picrylhydrazyl (DPPH) was obtained at an oil concentration of 50 mg·mL−1 (73.15%). The antioxidant activity evaluated by the Oxygen Radical Absorbance Capacity (ORAC) was 95.3 μmol Trolox equivalent·g−1 oil. These results serve to present Buriti oil as an Amazonian resource for cosmetic, food and pharmaceuticals purposes. (Author)

Randomised trial of coconut oil, olive oil or butter on blood lipids and other cardiovascular risk factors in healthy men and women.

OpenAIRE

Khaw, Kay-Tee; Sharp, Stephen John; Finikarides, Leila; Afzal, Islam; Lentjes, Maria Antonetta; Luben, Robert; Forouhi, Nita Gandhi

2018-01-01

Abstract Introduction: High dietary saturated fat intake is associated with higher blood concentrations of LDL-cholesterol, an established risk factor for coronary heart disease. However, there is increasing interest in whether various dietary oils or fats with different fatty acid profiles such as extra virgin coconut oil may have different metabolic effects but trials have reported inconsistent results. We aimed to compare changes in blood lipid profile, weight, fat distribution, an...

Nitrogen Saturation in Highly Retentive Watersheds?

Science.gov (United States)

Daley, M. L.; McDowell, W. H.

2009-12-01

Watershed managers are often concerned with minimizing the amount of N delivered to N-limited estuaries and coastal zones. A major concern is that watersheds might reach N saturation, in which N delivered to coastal zones increases due to declines in the efficiency of N retention despite constant or even reduced N inputs. We have quantified long-term changes in N inputs (atmospheric deposition, imported food and agricultural fertilizers), outputs (N concentration and export) and retention in the urbanizing Lamprey River watershed in coastal NH. Overall, the Lamprey watershed is 70% forested, receives about 13.5 kg N/ha/yr and has a high rate of annual N retention (85%). Atmospheric deposition (8.7 kg/ha/yr) is the largest N input to the watershed. Of the 2.2 kg N/ha/yr exported in the Lamprey River, dissolved organic N (DON) is the dominant form (50% of total) and it varies spatially throughout the watershed with wetland cover. Nitrate accounts for 30% of the N exported, shows a statistically significant increase from 1999 to 2009, and its spatial variability in both concentration and export is related to human population density. In sub-basins throughout the Lamprey, inorganic N retention is high (85-99%), but the efficiency of N retention declines sharply with increased human population density and associated anthropogenic N inputs. N assimilation in the vegetation, denitrification to the atmosphere and storage in the groundwater pool could all be important contributors to the current high rates of N retention. The temporal and spatial patterns that we have observed in nitrate concentration and export are driven by increases in N inputs and impervious surfaces over time, but the declining efficiency of N retention suggests that the watershed may also be reaching N saturation. The downstream receiving estuary, Great Bay, already suffers from low dissolved oxygen levels and eelgrass loss in part due to N loading from the Lamprey watershed. Targeting and reducing

Pressure and fluid saturation prediction in a multicomponent reservoir, using combined seismic and electromagnetic imaging

International Nuclear Information System (INIS)

Hoversten, G.M.; Gritto, Roland; Washbourne, John; Daley, Tom

2002-01-01

This paper presents a method for combining seismic and electromagnetic measurements to predict changes in water saturation, pressure, and CO 2 gas/oil ratio in a reservoir undergoing CO 2 flood. Crosswell seismic and electromagnetic data sets taken before and during CO 2 flooding of an oil reservoir are inverted to produce crosswell images of the change in compressional velocity, shear velocity, and electrical conductivity during a CO 2 injection pilot study. A rock properties model is developed using measured log porosity, fluid saturations, pressure, temperature, bulk density, sonic velocity, and electrical conductivity. The parameters of the rock properties model are found by an L1-norm simplex minimization of predicted and observed differences in compressional velocity and density. A separate minimization, using Archie's law, provides parameters for modeling the relations between water saturation, porosity, and the electrical conductivity. The rock-properties model is used to generate relationships between changes in geophysical parameters and changes in reservoir parameters. Electrical conductivity changes are directly mapped to changes in water saturation; estimated changes in water saturation are used along with the observed changes in shear wave velocity to predict changes in reservoir pressure. The estimation of the spatial extent and amount of CO 2 relies on first removing the effects of the water saturation and pressure changes from the observed compressional velocity changes, producing a residual compressional velocity change. This velocity change is then interpreted in terms of increases in the CO 2 /oil ratio. Resulting images of the CO 2 /oil ratio show CO 2 -rich zones that are well correlated to the location of injection perforations, with the size of these zones also correlating to the amount of injected CO 2 . The images produced by this process are better correlated to the location and amount of injected CO 2 than are any of the individual

Vitamin A degradation in triglycerides varying by their saturation levels.

Science.gov (United States)

Moccand, Cyril; Martin, Fréderic; Martiel, Isabelle; Gancel, Charlotte; Michel, Martin; Fries, Lennart; Sagalowicz, Laurent

2016-10-01

Vitamin A deficiency has a widespread occurrence globally and is considered as one of the world's most serious health risk factors. Potential solutions to address this deficiency include dietary diversification or supplementation, but food fortification is generally accepted as the most cost-effective solution. The main issue with food fortification of this vitamin is related to its high instability in food matrices. Dilution of vitamin A in triglycerides is a natural and appropriate way to stabilize this compound. We show here that vitamin A palmitate stability increases with increasing concentration of triglycerides. Moreover, we found that vitamin A palmitate displays improved stability in more saturated oils. Using various temperatures, and Arrhenius plots of experiments performed at storage temperatures between 30°C and 60°C for oils varying by their saturation and crystallinity, we demonstrate that crystallization is not responsible for this phenomenon. Additionally, we show by centrifugation that vitamin A is preferably solubilized in the liquid phase compared to the crystalline phase, explaining that triglyceride crystallization does not stabilize vitamin A palmitate. It is proposed that unsaturated fats generate more oxidation products such as radicals and peroxides, leading to a quicker degradation of vitamin A. Copyright © 2016 Elsevier Ltd. All rights reserved.

PARTON SATURATION, PRODUCTION, AND EQUILIBRATION IN HIGH ENERGY NUCLEAR COLLISIONS

International Nuclear Information System (INIS)

VENUGOPALAN, R.

1999-01-01

Deeply inelastic scattering of electrons off nuclei can determine whether parton distributions saturate at HERA energies. If so, this phenomenon will also tell us a great deal about how particles are produced, and whether they equilibrate, in high energy nuclear collisions

Avocado and olive oil methyl esters

International Nuclear Information System (INIS)

Knothe, Gerhard

2013-01-01

Biodiesel, the mono-alkyl esters of vegetable oils, animal fats or other triacylglycerol-containing materials and an alternative to conventional petroleum-based diesel fuel, has been derived from a variety of feedstocks. Numerous feedstocks have been investigated as potential biodiesel sources, including commodity oils, however, the methyl esters of avocado and olive oil would likely be suitable as biodiesel fuel. In order to expand the database and comprehensive evaluation of the properties of vegetable oil esters, in this work the fuel-related properties of avocado and olive oil methyl esters, which exhibit similar fatty acid profiles including high oleic acid content, are determined. The cetane numbers of avocado oil methyl esters and olive oil methyl esters are relatively high, determined as 59.2 and 62.5, respectively, due to their elevated content of methyl oleate. Other properties are well within the ranges specified in biodiesel standards. The cloud points of both esters are slightly above 0 °C due to their content of saturated esters, especially methyl palmitate. Overall, avocado and olive oil yield methyl esters with fuel properties comparable to methyl esters from other commodity vegetable oils. The 1 H and 13 C NMR spectra of avocado and olive oil methyl esters are reported. -- Highlights: • Methyl esters of avocado and olive oil meet biodiesel fuel standards. • Provides comparison for methyl esters of other vegetable oils with high oleic content. • Discusses and compares present results with prior literature

Pore-scale modelling of the effect of viscous pressure gradients during heavy oil depletion experiments

Energy Technology Data Exchange (ETDEWEB)

Bondino, I. [Total E and P UK Ltd., London (United Kingdom); McDougall, S.R. [Heriot-Watt Univ., Edinburgh (United Kingdom); Hamon, G. [Total E and P Canada Ltd., Calgary, AB (Canada)

2009-07-01

In solution gas drive, when the reservoir pressure is lowered below the bubble point, bubbles nucleate and grow within saturated oil. A period of internal gas-phase expansion maintains reservoir pressure, driving oil to the wellbore region. Continued pressure reduction eventually leads to the formation of a connected gas phase that is capable of being produced along with the oleic phase. As a result, the total produced gas-oil ratio in the well begins to increase. Once the connected gas phase develops, oil production begins to decrease. This general description can be inadequate in the context of heavy oils where additional characteristics, such as foamy oil, and atypically high recoveries are observed. In order to improve the simulation of solution gas drive for heavy oil in the framework of a pre-existing pore-scale network simulator, a dynamic gas-oil interface tracking algorithm was used to determine the mobilization of bubbles under intense pressure gradients. The model was used to characterize both the stationary capillary controlled growth of bubbles characteristic of slow depletion rates in the far wellbore region and the flow phenomena in the near wellbore region. A rationale for interpreting a range of flow mechanism, their associated gas relative permeabilities and critical gas saturations was also proposed. The paper first presented a description of the dynamic pore network model in terms of its' ability to model the porous space; and mobilize gas under viscous pressure gradients and unsteady-state gas relative permeabilities. The dynamic network modelling of heavy oil depletion experiments at different rates and the prediction of the experimental gas saturations were then presented along with a discussion on critical gas saturations. It was concluded that foamy oil behaviour can be observed in situations where capillary pressures are overcome by viscous pressure gradients. 47 refs., 5 tabs., 17 figs.

Association between hepatic cholesterol and oleic acid in the liver of rats treated with partially hydrogenated vegetable oil

Directory of Open Access Journals (Sweden)

Gabriela Salim Ferreira de Castro

2012-02-01

Full Text Available OBJECTIVE: The aim of the present study was to investigate the lipid profiles of the hepatic and adipose tissues of Wistar rats treated for 21 days with a diet high in saturated fat (high saturated fat, n=6 or high in hydrogenated fat, that is, having 50% partially hydrogenated vegetable oil in its composition (high hydrogenated fat, n=6, and compare them to those of a control group (control group, n=6. METHODS: Adipose tissue and total hepatic fat were higher in the saturated fat group than in the hydrogenated fat group. Hepatic lipid peroxidation was greatest in the saturated fat group, with consequent lower hepatic vitamin E and A levels. In contrast, serum vitamin A was highest in the saturated fat group. Analysis of hepatic lipid fractions found more cholesterol and less high density lipoprotein-cholesterol in the hydrogenated fat group. The hydrogenated fat group had the highest levels of triacylglycerols, followed by the saturated fat group. RESULTS: Significant amounts of trans fatty acids were detected in the hepatic and adipose tissues of the hydrogenated fat group. Among the identified fatty acids, 18:1n9 had a higher positive association with hepatic cholesterol and triacylglycerols, and a higher negative association with high density lipoprotein-cholesterol. Partially hydrogenated vegetable oil promotes greater accumulation of cholesterol and triacylglycerols in the liver than saturated fats. CONCLUSION: Trans fatty acids were incorporated into hepatocytes and adipocytes in a highly efficient manner.

Vegetable oil based liquid nanocomposite dielectric

Directory of Open Access Journals (Sweden)

Leon Chetty

2013-01-01

Full Text Available Physically smaller dielectric materials would improve the optimisation of space for power systems. Development of nanotechnology provides an effective way to improve the performances of insulating oils used in power system applications. In this research study, we focused on the development of nanomodified vegetable oils to be used in power transformers. Higher conduction currents were observed in virgin linseed oil than in virgin castor oil. However, for both virgin linseed and virgin castor oil, the DC conduction current increased approximately linearly with the applied DC voltage. In nanomodified linseed oil, the characteristic curve showed two distinct regions: a linear region (at lower applied voltage and a saturation region (at slightly higher voltage. Conversely, in nanomodified castor oil, the characteristic curve showed three distinct regions: a linear region (at lower applied voltage, a saturation region (at intermediate applied voltage and an exponential growth region (at higher applied voltage. The nanomodified linseed oil exhibited a better dielectric performance than the nanomodified castor oil. Overall, the addition of nanodielectrics to vegetable oils decreased the dielectric performance of the vegetable oils. The results of this study contribute to the understanding of the pre-breakdown phenomenon in liquid nanocomposite dielectrics.

Configuration de piégeage dans un milieu poreux à saturation résiduelle en huile Configuration of Trapping in a Porous Medium with Residual Oil Saturation

Directory of Open Access Journals (Sweden)

Sylvestre L.

2006-11-01

ainsi, d'une part, situer le comportement du milieu poreux par rapport aux deux états de référence précédemment définis et d'autre part, nous avons pu estimer la fraction du volume poreux en écoulement, la composition des zones stagnantes et leur taille moyenne, en fonction de la saturation en huile. L'analyse critique de ces résultats nous permet de conclure que, si certains comportements sont vraisemblablement caractéristiques de notre mode opératoire expérimental et du milieu poreux étudié, la technique mise au point (traçage et interprétation par un modèle PDE pourrait être utilisée avec succès dans le cas de milieux poreux réels. This article analyzes the hydrodynamics and spatial distribution of liquid phases in a porous medium with residual oil saturation. Experiments were performed in a porous medium made up of glass beads piled up in a column. Water drive was used to achieve decane saturations of up to 30% pore volume. The sweep water was traced during each experiment by a dyestuff that was insoluble in oil. The distribution curves of the tracer residence time, obtained upon issuing from the medium, were analyzed by a chromatographic model of the piston-dispersion type with exchange (PDE. This model covers all the pores in which the sweeping phase is flowing as well as the stagnant sections containing trapped water and oil. In the first phase an analysis of equations led to a definition, in the form of adimensional variables, of the penetrability of the porous medium and of the time constants respectively characterizing flow in the mobile phase and diffusion in stagnant zones. An examination of the influence of these variables on the flows transferred led to a definition of the state of distribution equilibrium of the solute between the stagnant and mobile phases. Two reference situations were chosen: (i equilibrium almost reached, and (ii negligible penetration of stagnant zones. On these bases, correlations were established between the

Nuclear determination of saturation profiles in core plugs

International Nuclear Information System (INIS)

Sletsgaard, J.; Oelgaard, P.L.

1997-01-01

A method to determine liquid saturations in core plugs during flooding is of importance when the relative permeability and capillary pressure function are to be determined. This part of the EFP-95 project uses transmission of γ-radiation to determine these saturations. In γ-transmission measurements, the electron density of the given substance is measured. This is an advantage as compared to methods that use electric conductivity, since neither oil nor gas conducts electricity. At the moment a single 137 Cs-source is used, but a theoretical investigation of whether it is possible to determine three saturations, using two radioactive sources with different γ-energies, has been performed. Measurements were made on three core plugs. To make sure that the measurements could be reproduced, all the plugs had a point of reference, i.e. a mark so that it was possible to place the plug same way every time. Two computer programs for calculation of saturation and porosity and the experimental setup are listed. (EG)

The comparison of naturally weathered oil and artificially photo-degraded oil at the molecular level by a combination of SARA fractionation and FT-ICR MS

International Nuclear Information System (INIS)

Islam, Ananna; Cho, Yunju; Yim, Un Hyuk; Shim, Won Joon; Kim, Young Hwan; Kim, Sunghwan

2013-01-01

Highlights: • Weathered oils from the Hebei Spirit oil spill and photo degraded oils are compared. • We investigate changes of polar species at the molecular level by 15T FT-ICR MS. • Significant reduction of sulfur class compounds in saturates fraction is observed. • The relative abundance of protonated compounds (presumably basic nitrogen compounds) increase after degradation. • Changes of polar compounds occurred by natural and photo degradation are similar. -- Abstract: Two sets of oil samples, one obtained from different weathering stages of the M/V Hebei Spirit oil spill site and the other prepared by an in vitro photo-degradation experiment, were analyzed and compared at the molecular level by atmospheric pressure photo-ionization coupled with Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS). For a more detailed comparison at the molecular level, the oil samples were separated into saturate, aromatic, resin, and asphaltene (SARA) fractions before MS analysis. Gravimetric analysis of the SARA fractions revealed a decreased weight percentage of the aromatic fraction and an increased resin fraction in both sets of samples. Molecular-level investigations of the SARA fractions showed a significant reduction in the S 1 class in the saturate fraction and increase of S 1 O 1 class compounds with high DBE values in resin fraction. Levels of N 1 and N 1 O 1 class compounds resulting in protonated ions (presumably basic nitrogen compounds) increased after degradation compared to compounds generating molecular ions (presumably non-basic nitrogen compounds). This study revealed changes occurring in heteroatom polar species of crude oils such as sulfur and nitrogen containing compounds that have not been easily detected with conventional GC based techniques

The effect of dietary lipid saturation and monensin-Na on the CLA ...

African Journals Online (AJOL)

One diet contained no ionophore antibiotic and the other monensin-Na included at 165 g/ton. These two basal diets were supplemented, according to a 2 x 3 factorial design, with three lipid sources [i.e. 20 g/kg of either beef tallow, sunflower oil or a CLA oil concentrate] differing in saturation level and fatty acid profile.

Fatty acid composition of maize germ oil from high-oil hybrids wet-milling processing

Directory of Open Access Journals (Sweden)

Jovanović Petar Lj.

2005-01-01

Full Text Available Maize germ was obtained by wet-milling laboratory processing of domestic high-oil maize hybrids. After separation, the germ was subjected to extraction of maize oil. Fatty acid composition of maize germ oil was determined by gas chromatography. The results showed very high levels of unsaturated fatty acids and a constant sum of oleic and linoleic acids in oils of different maize hybrids.

Characterization and Alteration of Wettability States of Alaskan Reserviors to Improve Oil Recovery Efficiency (including the within-scope expansion based on Cyclic Water Injection - a pulsed waterflood for Enhanced Oil Recovery)

Energy Technology Data Exchange (ETDEWEB)

Abhijit Dandekar; Shirish Patil; Santanu Khataniar

2008-12-31

Numerous early reports on experimental works relating to the role of wettability in various aspects of oil recovery have been published. Early examples of laboratory waterfloods show oil recovery increasing with increasing water-wetness. This result is consistent with the intuitive notion that strong wetting preference of the rock for water and associated strong capillary-imbibition forces gives the most efficient oil displacement. This report examines the effect of wettability on waterflooding and gasflooding processes respectively. Waterflood oil recoveries were examined for the dual cases of uniform and non-uniform wetting conditions. Based on the results of the literature review on effect of wettability and oil recovery, coreflooding experiments were designed to examine the effect of changing water chemistry (salinity) on residual oil saturation. Numerous corefloods were conducted on reservoir rock material from representative formations on the Alaska North Slope (ANS). The corefloods consisted of injecting water (reservoir water and ultra low-salinity ANS lake water) of different salinities in secondary as well as tertiary mode. Additionally, complete reservoir condition corefloods were also conducted using live oil. In all the tests, wettability indices, residual oil saturation, and oil recovery were measured. All results consistently lead to one conclusion; that is, a decrease in injection water salinity causes a reduction in residual oil saturation and a slight increase in water-wetness, both of which are comparable with literature observations. These observations have an intuitive appeal in that water easily imbibes into the core and displaces oil. Therefore, low-salinity waterfloods have the potential for improved oil recovery in the secondary recovery process, and ultra low-salinity ANS lake water is an attractive source of injection water or a source for diluting the high-salinity reservoir water. As part of the within-scope expansion of this project

Effect of consumption of phenols from olives and extra virgin olive oil on LDL oxidizability in healthy humans

NARCIS (Netherlands)

Vissers, M.N.; Zock, P.L.; Leenen, R.; Roodenburg, A.J.C.; Putte, van K.P.A.M.; Katan, M.B.

2001-01-01

A high intake of olive oil has been proposed as an explanation for the low incidence of coronary heart disease in Mediterranean countries, but it is unclear whether olive oil offers specific benefits beyond a low content of saturated fat. Some types of extra virgin olive oil are rich in non-polar

New insights into oxidation behaviours of crude oils

Energy Technology Data Exchange (ETDEWEB)

Li, J.; Mehta, S.A.; Moore, R.G. [Calgary Univ., AB (Canada)

2006-07-01

Innovative technologies will be needed to develop many of the world's oil reservoirs in an economically sustainable manner. In recent years, air injection for light oil reservoirs has gained recognition as an Improved Oil Recovery (IOR) process. In this process, the oxygen from the injected air reacts with a small fraction of the reservoir oil at high temperature to produce a mixture of carbon dioxide and nitrogen. The produced gas generated by the reaction mobilizes the oil downstream, thereby sweeping oil towards the production wells. High pressure air injection used in light oil reservoirs differs from the process used in heavy oil reservoirs, despite the fact that various oxidation reaction schemes exist. The key challenge facing the air injection process is the complexity of the oxidation reaction for crude oil and the lack of understanding of the oxidation behavior of light oils. This study identified a range of oxidation behaviors between light oil and heavy oil. The relationship between crude oil composition and its oxidation behaviors was also examined with reference to 3 different oils and their SARA (saturates, aromatics, resins and asphaltenes) fractions. This study was carried out at various pressures and temperatures using thermogravimetry and pressurized differential scanning calorimetry (PDSC) as the thermal analysis techniques.

INCREASING WATERFLOOD RESERVES IN THE WILMINGTON OIL FIELD THROUGH IMPROVED RESERVOIR CHARACTERIZATION AND RESERVOIR MANAGEMENT

Energy Technology Data Exchange (ETDEWEB)

Scott Walker; Chris Phillips; Roy Koerner; Don Clarke; Dan Moos; Kwasi Tagbor

2002-02-28

This project increased recoverable waterflood reserves in slope and basin reservoirs through improved reservoir characterization and reservoir management. The particular application of this project is in portions of Fault Blocks IV and V of the Wilmington Oil Field, in Long Beach, California, but the approach is widely applicable in slope and basin reservoirs. Transferring technology so that it can be applied in other sections of the Wilmington Field and by operators in other slope and basin reservoirs is a primary component of the project. This project used advanced reservoir characterization tools, including the pulsed acoustic cased-hole logging tool, geologic three-dimensional (3-D) modeling software, and commercially available reservoir management software to identify sands with remaining high oil saturation following waterflood. Production from the identified high oil saturated sands was stimulated by recompleting existing production and injection wells in these sands using conventional means as well as a short radius redrill candidate. Although these reservoirs have been waterflooded over 40 years, researchers have found areas of remaining oil saturation. Areas such as the top sand in the Upper Terminal Zone Fault Block V, the western fault slivers of Upper Terminal Zone Fault Block V, the bottom sands of the Tar Zone Fault Block V, and the eastern edge of Fault Block IV in both the Upper Terminal and Lower Terminal Zones all show significant remaining oil saturation. Each area of interest was uncovered emphasizing a different type of reservoir characterization technique or practice. This was not the original strategy but was necessitated by the different levels of progress in each of the project activities.

Coconut oil and palm oil's role in nutrition, health and national development: A review.

Science.gov (United States)

Boateng, Laurene; Ansong, Richard; Owusu, William B; Steiner-Asiedu, Matilda

2016-09-01

Coconut and palm oils which were the major sources of dietary fats for centuries in most of West Africa have been branded as unhealthy highly saturated fats. Their consumption has been peddled to supposedly raise the level of blood cholesterol, thereby increasing the risk of coronary heart disease. This adverse view has led to a reduction in their consumption in West Africa and they have been substituted for imported vegetable oils. Recent information however, indicates some beneficial effects of these oils particularly their roles in nutrition, health and national development. There is the need for a better understanding of their effects on health, nutritional status and national development. This paper therefore attempts to review the roles which coconut and palm oils play in these respects in developing countries, as a means of advocating for a return to their use in local diets. None declared.

Evaluation of Palm Oil as a Suitable Vegetable Oil for Vitamin A Fortification Programs.

Science.gov (United States)

Pignitter, Marc; Hernler, Natalie; Zaunschirm, Mathias; Kienesberger, Julia; Somoza, Mark Manuel; Kraemer, Klaus; Somoza, Veronika

2016-06-21

Fortification programs are considered to be an effective strategy to mitigate vitamin A deficiency in populations at risk. Fortified vegetable oils rich in polyunsaturated fatty acids were shown to be prone to oxidation, leading to limited vitamin A stability. Thus, it was hypothesized that fortified oils consisting of mainly saturated fatty acids might enhance the stability of vitamin A. Mildly (peroxide value: 1.0 meq O₂/kg) and highly (peroxide value: 7.5 meq O₂/kg) oxidized palm oil was stored, after fortification with 60 International Units/g retinyl palmitate, in 0.5 L transparent polyethylene terephthalate bottles under cold fluorescent lighting (12 h/day) at 32 °C for 57 days. An increase of the peroxide value by 15 meq O₂/kg, which was also reflected by a decrease of α-tocopherol congener by 15%-18%, was determined independent of the initial rancidity. The oxidative deterioration of the highly oxidized palm oil during storage was correlated with a significant 46% decline of the vitamin A content. However, household storage of mildly oxidized palm oil for two months did not induce any losses of vitamin A. Thus, mildly oxidized palm oil may be recommended for vitamin A fortification programs, when other sources of essential fatty acids are available.

Enhancement of Hydrodynamic Processes in Oil Pipelines Considering Rheologically Complex High-Viscosity Oils

Science.gov (United States)

Konakhina, I. A.; Khusnutdinova, E. M.; Khamidullina, G. R.; Khamidullina, A. F.

2016-06-01

This paper describes a mathematical model of flow-related hydrodynamic processes for rheologically complex high-viscosity bitumen oil and oil-water suspensions and presents methods to improve the design and performance of oil pipelines.

Effects of high-pressure process on kinetics of leaching oil from soybean powder using hexane in batch systems.

Science.gov (United States)

Uhm, Joo Tae; Yoon, Won Byong

2011-08-01

Mass transfer models of leaching oil from soybean (Glycine max) flour with hexane after high-pressure process (HPP) treatment were developed. High pressure (450 MPa) was applied to the soybean flour (mean diameter of flour particle: 365 μm) for 30 min before leaching the oil components in the solvent. The ratio of solvent (volume, mL) to soybean flour (mass, g), such as 1:10 and 1:20, was employed to characterize the effect of solvent ratio on the leaching rate in the batch type of extraction process. Ultraviolet absorbance at 300 nm was used to monitor the extraction rate. Saturation solubility (C(AS)) was determined to be 21.73 kg/m³. The mass transfer coefficients (k) were determined based on the 1st- and 2nd-order kinetic models. The 2nd kinetic model showed better fit. The HPP treatment showed a higher extraction rate and yield compared to the control, while the amount of solvent did not affect the extraction rate and yield. The scanning electron microscope showed that HPP-treated soybean particles included more pores than the untreated. The pores observed in the HPP-treated soybean flours might help increase the mass transfer rate of solvent and solute in the solid matrix. High-pressure processing can help increase the extraction rate of oil from the soybean flour operated in batch systems. The conventional solid to solvent ratio (1:20) used to extract oil composition from the plant seed did not help increase the amount of oil extracted from the soybean flour. © 2011 Institute of Food Technologists®

Coconut oil enhances tomato carotenoid tissue accumulation compared to safflower oil in the Mongolian gerbil ( Meriones unguiculatus ).

Science.gov (United States)

Conlon, Lauren E; King, Ryan D; Moran, Nancy E; Erdman, John W

2012-08-29

Evidence suggests that monounsaturated and polyunsaturated fats facilitate greater absorption of carotenoids than saturated fats. However, the comparison of consuming a polyunsaturated fat source versus a saturated fat source on tomato carotenoid bioaccumulation has not been examined. The goal of this study was to determine the influence of coconut oil and safflower oil on tomato carotenoid tissue accumulation in Mongolian gerbils ( Meriones unguiculatus ) fed a 20% fat diet. Coconut oil feeding increased carotenoid concentrations among many compartments including total carotenoids in the serum (p = 0.0003), adrenal glandular phytoene (p = 0.04), hepatic phytofluene (p = 0.0001), testicular all-trans-lycopene (p = 0.01), and cis-lycopene (p = 0.006) in the prostate-seminal vesicle complex compared to safflower oil. Safflower oil-fed gerbils had greater splenic lycopene concentrations (p = 0.006) compared to coconut oil-fed gerbils. Coconut oil feeding increased serum cholesterol (p = 0.0001) and decreased hepatic cholesterol (p = 0.0003) compared to safflower oil. In summary, coconut oil enhanced tissue uptake of tomato carotenoids to a greater degree than safflower oil. These results may have been due to the large proportion of medium-chain fatty acids in coconut oil, which might have caused a shift in cholesterol flux to favor extrahepatic carotenoid tissue deposition.

High oil prices: A non-OPEC capacity game

International Nuclear Information System (INIS)

Osmundsen, Petter; Asche, Frank; Misund, Baard; Mohn, Klaus

2005-08-01

The current high oil price is partly due to low investments in the oil industry the last decade. According to economic theory, exploration and development of new oil and gas fields should respond positively to increasing petroleum prices. But since the late 1990s, financial analysts have focused strongly on short-term accounting return measures, like RoACE, for benchmarking and valuation of international oil and gas companies. Consequently, the demand for strict capital discipline among oil and gas companies may have reduced their willingness to invest for future reserves and production growth. Thus, we have experienced an unusual combination of high oil prices and low investment levels in exploration and development. In many ways, the oil companies' focus on RoACE, at the expense of reserve replacement, resembles an implicit co-ordination on low capacity among non-OPEC petroleum producers. This is a partial explanation of the current high oil prices. By examining actual parameters used by the financial markets in pricing of oil companies, we address the issue of whether the low investment outcome could represent a long-term equilibrium. This is hardly likely, as oil companies are made aware that stronger emphasis is put on reserve replacement. (Author)

Extraction of rice bran oil from local rice husk

International Nuclear Information System (INIS)

Anwar, J.; Zaman, W.; Salman, M.; Jabeen, N.

2006-01-01

Rice Bran Oil is widely used in pharmaceutical, food and chemical industries due to its unique properties and high medicinal value. In the present work, extraction of rice bran oil from different samples of rice husk collected from local rice shellers by solvent extraction method has been studied. Experiments were conducted using a soxhelt apparatus, to extract rice bran oil using hexane, petroleum ether, ethanol and methanol as the solvents and the yields obtained under different conditions were compared. Batch extraction tests showed that the rate of extraction decreases with time and the solution approaches saturation at an exponential rate. (author)

The Effects of High and Volatile Oil Prices

International Nuclear Information System (INIS)

Artus, Patrick; Autume, Antoine d'; Chalmin, Philippe; Chevalier, Jean-Marie; Coeure, Benoit; Kalantizs, Yannick; Klein, Caroline; Guesnerie, Roger; Callonnec, Gael; Gaudin, Thomas; Moisan, Francois; Lescaroux, Francois; Clerc, Marie; Marcus, Vincent; Lalanne, Guy; Pouliquen, Erwan; Simon, Olivier; Mignon, Valerie

2010-01-01

demand into play (this is estimated at around 0.2 in the short term and around 0.4 over the longer term for fuel demand) and possibly caused behavioural changes such as those seen in France and described in the report. The other explanation is related to energy and environmental policies, which have helped reduce oil demand. However, the strong growth expected in emerging markets is likely to increase global demand for oil by several million barrels per day by 2014. This reflects the expectation that the number of cars on the road worldwide will double by 2030, and it seems unlikely that tougher environmental constraints will contain these trends. Half of this growth will come from Asia. Such an increase in global oil demand will only be sustainable if it is accompanied by higher prices that will enable the exploitation of new unconventional oil fields or fields with high production costs. As regards volatility, the authors first repeat that there are real determinants at play: the level of oil prices encourages or discourages investment in production capacity. Low oil prices slow capacity investments and therefore limit future supply, which then causes prices to rise, thereby providing an incentive to invest and develop supply. However, neither these (endogenous) irregularities in the investment programs of oil companies and exporting countries nor changing demand trends alone can account for the sharp rise in prices between 2002 and 2008 and the very sudden drop that followed in July-August 2008. A number of observers believe that the explanation lies in speculation on the oil market. The report's authors sift through all the arguments for and against this theory. While it is undeniable that speculation has developed on the oil futures market, the authors question two key points: was this speculation really focused on an oil price rally, and could it have such a significant retroactive effect on spot prices? Their conclusions recognise that speculation was indeed

Saturated Adaptive Output-Feedback Power-Level Control for Modular High Temperature Gas-Cooled Reactors

Directory of Open Access Journals (Sweden)

Zhe Dong

2014-11-01

Full Text Available Small modular reactors (SMRs are those nuclear fission reactors with electrical output powers of less than 300 MWe. Due to its inherent safety features, the modular high temperature gas-cooled reactor (MHTGR has been seen as one of the best candidates for building SMR-based nuclear plants with high safety-level and economical competitive power. Power-level control is crucial in providing grid-appropriation for all types of SMRs. Usually, there exists nonlinearity, parameter uncertainty and control input saturation in the SMR-based plant dynamics. Motivated by this, a novel saturated adaptive output-feedback power-level control of the MHTGR is proposed in this paper. This newly-built control law has the virtues of having relatively neat form, of being strong adaptive to parameter uncertainty and of being able to compensate control input saturation, which are given by constructing Lyapunov functions based upon the shifted-ectropies of neutron kinetics and reactor thermal-hydraulics, giving an online tuning algorithm for the controller parameters and proposing a control input saturation compensator respectively. It is proved theoretically that input-to-state stability (ISS can be guaranteed for the corresponding closed-loop system. In order to verify the theoretical results, this new control strategy is then applied to the large-range power maneuvering control for the MHTGR of the HTR-PM plant. Numerical simulation results show not only the relationship between regulating performance and control input saturation bound but also the feasibility of applying this saturated adaptive control law practically.

Enhancement of recovery of residual oil using a biosurfactant slug ...

African Journals Online (AJOL)

Characterization of the biosurfactant extract revealed a mixture of glycolipid and phospholipid in a ratio of 3.35:1. The irreducible water saturation (Swi) and initial residual oil saturation (Sor) of the sand-pack were 0.280 ± 0.003 and 0.373 ± 0.006, respectively. Core flooding experiment showed that an optimum oil recovery ...

Traffic signal synchronization in the saturated high-density grid road network.

Science.gov (United States)

Hu, Xiaojian; Lu, Jian; Wang, Wei; Zhirui, Ye

2015-01-01

Most existing traffic signal synchronization strategies do not perform well in the saturated high-density grid road network (HGRN). Traffic congestion often occurs in the saturated HGRN, and the mobility of the network is difficult to restore. In order to alleviate traffic congestion and to improve traffic efficiency in the network, the study proposes a regional traffic signal synchronization strategy, named the long green and long red (LGLR) traffic signal synchronization strategy. The essence of the strategy is to control the formation and dissipation of queues and to maximize the efficiency of traffic flows at signalized intersections in the saturated HGRN. With this strategy, the same signal control timing plan is used at all signalized intersections in the HGRN, and the straight phase of the control timing plan has a long green time and a long red time. Therefore, continuous traffic flows can be maintained when vehicles travel, and traffic congestion can be alleviated when vehicles stop. Using the strategy, the LGLR traffic signal synchronization model is developed, with the objective of minimizing the number of stops. Finally, the simulation is executed to analyze the performance of the model by comparing it to other models, and the superiority of the LGLR model is evident in terms of delay, number of stops, queue length, and overall performance in the saturated HGRN.

Shear dilatancy and acoustic emission in dry and saturated granular materials

Science.gov (United States)

Brodsky, E. E.; Siman-Tov, S.

2017-12-01

Shearing of granular materials plays a strong role in naturally sheared systems as landslides and faults. Many works on granular flows have concentrated on dry materials, but relatively little work has been done on water saturated sands. Here we experimentally investigate dry versus saturated quartz-rich sand to understand the effect of the fluid medium on the rheology and acoustic waves emission of the sheared sand. The sand was sheared in a rotary shear rheometer under applied constant normal stress boundary at low (100 µm/s) to high (1 m/s) velocities. Mechanical, acoustic data and deformation were continuously recorded and imaged. For dry and water saturated experiments the granular volume remains constant for low shear velocities ( 10-3 m/s) and increases during shearing at higher velocities ( 1 m/s). Continuous imaging of the sheared sand show that the steady state shear band thickness is thicker during the high velocity steps. No significant change observed in the shear band thickness between dry and water saturated experiments. In contrast, the amount of dilation during water saturated experiments is about half the value measured for dry material. The measured decrease cannot be explained by shear band thickness change as such is not exist. However, the reduced dilation is supported by our acoustic measurements. In general, the event rate and acoustic event amplitudes increase with shear velocity. While isolated events are clearly detected during low velocities at higher the events overlap, resulting in a noisy signal. Although detection is better for saturated experiments, during the high velocity steps the acoustic energy measured from the signal is lower compared to that recorded for dry experiments. We suggest that the presence of fluid suppresses grain motion and particles impacts leading to mild increase in the internal pressure and therefore for the reduced dilation. In addition, the viscosity of fluids may influence the internal pressure via

A randomized study of coconut oil versus sunflower oil on cardiovascular risk factors in patients with stable coronary heart disease

Directory of Open Access Journals (Sweden)

Maniyal Vijayakumar

2016-07-01

Conclusion: Coconut oil even though rich in saturated fatty acids in comparison to sunflower oil when used as cooking oil media over a period of 2 years did not change the lipid-related cardiovascular risk factors and events in those receiving standard medical care.

Biological and Nutritional Properties of Palm Oil and Palmitic Acid: Effects on Health.

Science.gov (United States)

Mancini, Annamaria; Imperlini, Esther; Nigro, Ersilia; Montagnese, Concetta; Daniele, Aurora; Orrù, Stefania; Buono, Pasqualina

2015-09-18

A growing body of evidence highlights the close association between nutrition and human health. Fat is an essential macronutrient, and vegetable oils, such as palm oil, are widely used in the food industry and highly represented in the human diet. Palmitic acid, a saturated fatty acid, is the principal constituent of refined palm oil. In the last few decades, controversial studies have reported potential unhealthy effects of palm oil due to the high palmitic acid content. In this review we provide a concise and comprehensive update on the functional role of palm oil and palmitic acid in the development of obesity, type 2 diabetes mellitus, cardiovascular diseases and cancer. The atherogenic potential of palmitic acid and its stereospecific position in triacylglycerols are also discussed.

Influence of Oil Saturation Upon Spectral Induced Polarization of Oil Bearing Sands

Science.gov (United States)

The presence of oil in an unconsolidated granular porous material such as sand changes both the resistivity of the material and the value of the phase shift between the low-frequency current and the voltage. The resistivity and the phase angle can be written as a complex-valued r...

Coconut Oil

Science.gov (United States)

... known as "medium chain triglycerides." Some of these fats work differently than other types of saturated fat in the body. When applied ... in food amounts. But coconut oil contains a type of fat that can increase cholesterol levels. So people should ...

Seed oil from Harmal (Rhazya stricta Decne grown in Riyadh (Saudi Arabia: A potential source of δ-tocopherol

Directory of Open Access Journals (Sweden)

Imededdine Arbi Nehdi

2016-01-01

Full Text Available Rhazya stricta (R. stricta known as Harmal is widely distributed in Saudi Arabia and throughout the Middle East. It is used as a medicinal plant in traditional cultures and the seeds are a source of unsaturated oil. In the present study, tocol (tocopherol and tocotrienol, triacylglycerol, and fatty acid compositions, pigment content, thermal behavior, and various physicochemical properties of R. stricta oil were characterized to determine the potential uses of this seed oil. Our results indicate that the oil is a rich source of bioactive molecules, including δ-tocopherol (896 mg/100 g, γ-tocopherol (148 mg/100 g and carotenoids (15.67 mg/kg. The oil content of the seeds was 13.68% and the triacylglycerols mainly consisted of linoleic acid (59.03%, and oleic acid (27.01%. The major triacylglycerols were trilinoleate, dilinoleate and monolinoleate. The ratio of unsaturated to saturated fatty acids (UFA/SFA in the oil was high (9.20. Additionally, the oil showed a high degree of thermal stability and a low melting point of approximately −25 °C. These data indicate that R. stricta seed oil, which is low in saturated fats and rich in bioactive compounds, is potentially useful in food and pharmaceutical applications.

Fish oil prevents sucrose-induced fatty liver but exacerbates high-safflower oil-induced fatty liver in ddy mice.

Science.gov (United States)

Yamazaki, Tomomi; Nakamori, Akiko; Sasaki, Eriko; Wada, Satoshi; Ezaki, Osamu

2007-12-01

Diets high in sucrose/fructose or fat can result in hepatic steatosis (fatty liver). We analyzed the effects of dietary fish oil on fatty liver induced by sucrose, safflower oil, and butter in ddY mice. In experiment I, mice were fed a high-starch diet [70 energy% (en%) starch] plus 20% (wt/wt) sucrose in the drinking water or fed a high-safflower oil diet (60 en%) for 11 weeks. As a control, mice were fed a high-starch diet with drinking water. Fish oil (10 en%) was either supplemented or not. Mice supplemented with sucrose or fed safflower oil showed a 1.7-fold or 2.2-fold increased liver triglyceride content, respectively, compared with that of control mice. Fish oil completely prevented sucrose-induced fatty liver, whereas it exacerbated safflower oil-induced fatty liver. Sucrose increased SREBP-1c and target gene messenger RNAs (mRNAs), and fish oil completely inhibited these increases. In experiment II, mice were fed a high-safflower oil or a high-butter diet, with or without fish oil supplementation. Fish oil exacerbated safflower oil-induced fatty liver but did not affect butter-induced fatty liver. Fish oil increased expression of peroxisome proliferator-activated receptor gamma (PPARgamma) and target CD36 mRNA in safflower oil-fed mice. These increases were not observed in sucrose-supplemented or butter-fed mice. The effects of dietary fish oil on fatty liver differ according to the cause of fatty liver; fish oil prevents sucrose-induced fatty liver but exacerbates safflower oil-induced fatty liver. The exacerbation of fatty liver may be due, at least in part, to increased expression of liver PPARgamma.

Water saturation in shaly sands: logging parameters from log-derived values

International Nuclear Information System (INIS)

Miyairi, M.; Itoh, T.; Okabe, F.

1976-01-01

The methods are presented for determining the relation of porosity to formation factor and that of true resistivity of formation to water saturation, which were investigated through the log interpretation of one of the oil and gas fields of northern Japan Sea. The values of the coefficients ''a'' and ''m'' in porosity-formation factor relation are derived from cross-plot of porosity and resistivity of formation corrected by clay content. The saturation exponent ''n'' is determined from cross-plot of porosity and resistivity index on the assumption that the product of porosity and irreducible water saturation is constant. The relation of porosity to irreducible water saturation is also investigated from core analysis. The new logging parameters determined from the methods, a = 1, m = 2, n = 1.4, improved the values of water saturation by 6 percent in average, and made it easy to distinguish the points which belong to the productive zone and ones belonging to the nonproductive zone

The effect of ZnO nanoparticles on improved oil recovery in spontaneous imbibition mechanism of heavy oil production

Science.gov (United States)

Tajmiri, M.; Ehsani, M. R.; Mousavi, S. M.; Roayaei, E.; Emadi, A.

2015-07-01

Spontaneous imbibition (SI) gets a controversial subject in oil- wet carbonate reservoirs. The new concept of nanoparticles applications in an EOR area have been recently raised by researches about oil viscosity reduction and generate emulsion without surfactant. But a lot of questions have been remained about which nanoparticles can alter wettability from oil- wet to water- wet to improve oil recovery. This study introduces the new idea of adding ZnO nanoparticles (0.2%wt concentration) by experimental work on oil recovery. The main goals of this research were to prove that ZnO nanoparticles have the ability to reduce viscosity and also alter wettability. The ultimate objective was to determine the potential of these nanoparticles to imbibe into and displace oil. Through the use of Amott- cell, laboratory tests were conducted in two experiments on four cylindrical core samples (three sandstones and one carbonate) were taken from real Iranian heavy oil reservoir. In the first experiment, core samples were saturated by crude oil and in the second experiment, nanoparticles were flooding into core samples and then saturated by crude oil for about two weeks and after that they were immersed in distilled water and the amount of recovery was monitored during 30 days for both tests. We expected that ZnO nanoparticles decreased the surface tension which reduced the capillary forces through SI and wettability alteration took place towards a more water-wet system and caused the oil relative permeability to increase which dominated the gravitational forces to pull out the oil. Our results proved this expectation from ZnO nanoparticles clearly because carbonate core was oil- wet and the capillary pressure was high and negative to push water into the core so the original oil in place (OOIP) was zero whereas by adding ZnO nanoparticles OOIP was increased to 8.89%. SI yielded recovery values from 17.3, 2 and 15 without nanoparticles to 20.68, 17.57 and 36.2 % OOIP with

Nature, origin, and production characteristics of the Lower Silurian regional oil and gas accumulation, central Appalachian basin, United States

Science.gov (United States)

Ryder, R.; Zagorski, W.A.

2003-01-01

Low-permeability sandstones of the Lower Silurian regional oil and gas accumulation cover about 45,000 mi2 (117,000 km2) of the Appalachian basin and may contain as much as 30 tcf of recoverable gas resources. Major reservoirs consist of the "Clinton" sandstone and Medina Group sandstones. The stratigraphically equivalent Tuscarora Sandstone increases the area of the Lower Silurian regional accumulation (LSRA) by another 30,000 mi2 (78,000 km2). Approximately 8.7 tcf of gas and 400 million bbl of oil have been produced from the Clinton/Medina reservoirs since 1880. The eastern predominantly gas-bearing part of the LSRA is a basin-center gas accumulation, whereas the western part is a conventional oil and gas accumulation with hybrid features of a basin-center accumulation. The basin-center accumulations have pervasive gas saturation, water near irreducible saturation, and generally low fluid pressures. In contrast, the hybrid-conventional accumulations have less-pervasive oil and gas saturation, higher mobile-water saturation, and both normal and abnormally low fluid pressures. High mobile-water saturation in the hybrid-conventional reservoirs form the updip trap for the basin-center gas creating a broad transition zone, tens of miles wide, that has characteristics of both end-member accumulation types. Although the Tuscarora Sandstone part of the basin-center gas accumulation is pervasively saturated with gas, most of its constituent sandstone beds have low porosity and permeability. Commercial gas fields in the Tuscarora Sandstone are trapped in naturally fractured, faulted anticlines. The origin of the LSRA includes (1) generation of oil and gas from Ordovician black shales, (2) vertical migration through an overlying 1000-ft (305-m)-thick Ordovician shale; (3) abnormally high fluid pressure created by oil-to-gas transformation; (4) updip displacement of mobile pore water by overpressured gas; (5) entrapment of pervasive gas in the basin center; (6) postorogenic

Complex conductivity of oil-contaminated clayey soils

Science.gov (United States)

Deng, Y.; Revil, A.; Shi, X.

2017-12-01

Non-intrusive hydrogeophysical techniques have been wildly applied to detect organic contaminants because of the difference of electrical properties for contaminated soil. Among them, spectral induced polarization (SIP) has emerged as a promising tool for the identification of contamination due to its sensitivity to the chemistry of pore water, solid-fluid interfaces and fluid content. Previous works have investigated the influences of oil on the electrical signatures of porous media, which demonstrated the potentials of SIP in the detection of hydrocarbon contamination. However, few works have done on the SIP response of oil in clayey soils. In this study, we perform a set of SIP measurements on the clayey samples under different water saturations. These clayey soils are characterized by relatively high cation exchange capacity. The objective in this work is to test the empirical relationships between the three exponents, including the cementation exponent (m), the saturation exponent (n) and the quadrature conductivity exponent (p), which is expected to reduce the model parameters needed in geophysical and hydraulic properties predictions. Our results show that the complex conductivity are saturation dependent. The magnitude of both in-phase and quadrature conductivities generally decrease with decreasing water saturation. The shape of quadrature conductivity spectra slightly changes when water saturation decreases in some cases. The saturation exponent slightly increases with cation exchange capacity, specific surface area and clay content, with an average value around 2.05. Compared to saturation exponent, the quadrature conductivity exponent apparently increases with cation exchange capacity and specific surface area while has little to do with the clay content. Further, the results indicate that the quadrature conductivity exponent p does not strictly obey to p=n-1 as proposed by Vinegar and Waxman (1984). Instead, it mostly ranges between p=n-1.5 and p=n-0

Factors inhibiting bioremediation of soil contaminated with weathered oils and drill cuttings

International Nuclear Information System (INIS)

Chaillan, F.; Chaineau, C.H.; Point, V.; Saliot, A.; Oudot, J.

2006-01-01

Oily drill cuttings and a soil contaminated with weathered crude oils were treated by enhanced biodegradation under tropical conditions in industrial scaled experiments. Oil contaminants were characterized by gas chromatography and mass spectrometry. This allowed for the identification of a mixture of two crude oils in the contaminated soil. After 12 months of bioremediation process, the removal of hydrocarbons reached by biodegradation an extent of 60% although nutrient amendment with elevated concentration of N-urea had highly detrimental effects on the hydrocarbon degrading fungal populations due to the production of toxic concentration of ammonia gas by nitrification. The saturated hydrocarbons were extensively assimilated, though n-alkanes were not completely removed. Aromatic hydrocarbons were less degraded than saturated whereas resin and asphaltene fractions were, surprisingly, partly assimilated. In laboratory conditions, the residual hydrocarbons in the field-treated materials were 15-20% further degraded when metabolic byproducts resulting from biodegradation were diluted or removed. - Bioremediation of oil-polluted soils can be impaired if urea is used as nitrogen source, and metabolic byproducts can limit biodegradation rates in industrial scaled experiments

Evaluating the Influence of Pore Architecture and Initial Saturation on Wettability and Relative Permeability in Heterogeneous, Shallow-Shelf Carbonates

Energy Technology Data Exchange (ETDEWEB)

Byrnes, Alan P.; Bhattacharya, Saibal; Victorine, John; Stalder, Ken

2007-09-30

Thin (3-40 ft thick), heterogeneous, limestone and dolomite reservoirs, deposited in shallow-shelf environments, represent a significant fraction of the reservoirs in the U.S. midcontinent and worldwide. In Kansas, reservoirs of the Arbuckle, Mississippian, and Lansing-Kansas City formations account for over 73% of the 6.3 BBO cumulative oil produced over the last century. For these reservoirs basic petrophysical properties (e.g., porosity, absolute permeability, capillary pressure, residual oil saturation to waterflood, resistivity, and relative permeability) vary significantly horizontally, vertically, and with scale of measurement. Many of these reservoirs produce from structures of less than 30-60 ft, and being located in the capillary pressure transition zone, exhibit vertically variable initial saturations and relative permeability properties. Rather than being simpler to model because of their small size, these reservoirs challenge characterization and simulation methodology and illustrate issues that are less apparent in larger reservoirs where transition zone effects are minor and most of the reservoir is at saturations near S{sub wirr}. These issues are further augmented by the presence of variable moldic porosity and possible intermediate to mixed wettability and the influence of these on capillary pressure and relative permeability. Understanding how capillary-pressure properties change with rock lithology and, in turn, within transition zones, and how relative permeability and residual oil saturation to waterflood change through the transition zone is critical to successful reservoir management and as advanced waterflood and improved and enhanced recovery methods are planned and implemented. Major aspects of the proposed study involve a series of tasks to measure data to reveal the nature of how wettability and drainage and imbibition oil-water relative permeability change with pore architecture and initial water saturation. Focus is placed on

Composition of plasma and atheromatous plaque among coronary artery disease subjects consuming coconut oil or sunflower oil as the cooking medium.

Science.gov (United States)

Palazhy, Sabitha; Kamath, Prakash; Rajesh, P C; Vaidyanathan, Kannan; Nair, Shiv K; Vasudevan, D M

2012-12-01

Coconut oil, which is rich in medium-chain saturated fatty acids, is the principal cooking medium of the people of Kerala, India. Replacement of saturated fat with polyunsaturated fat is effective in reducing serum cholesterol levels. However, the effect of substituting coconut oil with sunflower oil on the fatty acid composition of plaque has not been thoroughly investigated. We therefore evaluated and compared the fatty acid composition of plasma and plaque among subjects consuming coconut oil or sunflower oil as the cooking medium. Endarterectomy samples and plasma samples were obtained from subjects who underwent coronary artery bypass grafts (n = 71). The subjects were grouped based on the type of oil they were using as their cooking medium (coconut oil or sunflower oil). The fatty acid composition in the plaques and the plasma was determined by HPLC and the data were analyzed statistically. Sunflower oil consumers had elevated concentrations of linoleic acid (p = 0.001) in plasma, while coconut oil users had higher myristic acid levels (p = 0.011) in plasma. Medium-chain fatty acids did not differ significantly between the two groups in the plasma. Medium-chain fatty acids were detected in the plaques in both groups of subjects. In contrast to previous reports, long-chain saturated fatty acids dominated the lipid content of plaque in this population, and the fatty acid composition of plaque was not significantly different between the two groups. No correlation between fatty acids of plasma and plaque was observed in either group. A change in cooking medium, although it altered the plasma fatty acid composition, was not reflected in the plaque composition.

Lipid order, saturation and surface property relationships: a study of human meibum saturation.

Science.gov (United States)

Mudgil, Poonam; Borchman, Douglas; Yappert, Marta C; Duran, Diana; Cox, Gregory W; Smith, Ryan J; Bhola, Rahul; Dennis, Gary R; Whitehall, John S

2013-11-01

Tear film stability decreases with age however the cause(s) of the instability are speculative. Perhaps the more saturated meibum from infants may contribute to tear film stability. The meibum lipid phase transition temperature and lipid hydrocarbon chain order at physiological temperature (33 °C) decrease with increasing age. It is reasonable that stronger lipid-lipid interactions could stabilize the tear film since these interactions must be broken for tear break up to occur. In this study, meibum from a pool of adult donors was saturated catalytically. The influence of saturation on meibum hydrocarbon chain order was determined by infrared spectroscopy. Meibum is in an anhydrous state in the meibomian glands and on the surface of the eyelid. The influence of saturation on the surface properties of meibum was determined using Langmuir trough technology. Saturation of native human meibum did not change the minimum or maximum values of hydrocarbon chain order so at temperatures far above or below the phase transition of human meibum, saturation does not play a role in ordering or disordering the lipid hydrocarbon chains. Saturation did increase the phase transition temperature in human meibum by over 20 °C, a relatively high amount. Surface pressure-area studies showing the late take off and higher maximum surface pressure of saturated meibum compared to native meibum suggest that the saturated meibum film is quite molecularly ordered (stiff molecular arrangement) and elastic (molecules are able to rearrange during compression and expansion) compared with native meibum films which are more fluid agreeing with the infrared spectroscopic results of this study. In saturated meibum, the formation of compacted ordered islands of lipids above the surfactant layer would be expected to decrease the rate of evaporation compared to fluid and more loosely packed native meibum. Higher surface pressure observed with films of saturated meibum compared to native meibum

Research on evaluation method for water saturation of tight sandstone in Suxi region

Science.gov (United States)

Lv, Hong; Lai, Fuqiang; Chen, Liang; Li, Chao; Li, Jie; Yi, Heping

2017-05-01

The evaluation of irreducible water saturation is important for qualitative and quantitative prediction of residual oil distribution. However, it is to be improved for the accuracy of experimental measuring the irreducible water saturation and logging evaluation. In this paper, firstly the multi-functional core flooding experiment and the nuclear magnetic resonance centrifugation experiment are carried out in the west of Sulige gas field. Then, the influence was discussed about particle size, porosity and permeability on the water saturation. Finally, the evaluation model was established about irreducible water saturation and the evaluation of irreducible water saturation was carried out. The results show that the results of two experiments are both reliable. It is inversely proportional to the median particle size, porosity and permeability, and is most affected by the median particle size. The water saturation of the dry layer is higher than that of the general reservoir. The worse the reservoir property, the greater the water saturation. The test results show that the irreducible water saturation model can be used to evaluate the water floor.

CGC/saturation approach for soft interactions at high energy: Inclusive production

International Nuclear Information System (INIS)

Gotsman, E.; Levin, E.; Maor, U.

2015-01-01

In this letter we demonstrate that our dipole model is successful in describing inclusive production within the same framework as diffractive physics. We believe that this achievement stems from the fact that our approach incorporates the positive features of the Reggeon approach and CGC/saturation effective theory, for high energy QCD

CGC/saturation approach for soft interactions at high energy: Inclusive production

Energy Technology Data Exchange (ETDEWEB)

Gotsman, E., E-mail: gotsman@post.tau.ac.il [Department of Particle Physics, School of Physics and Astronomy, Raymond and Beverly Sackler Faculty of Exact Science, Tel Aviv University, Tel Aviv, 69978 (Israel); Levin, E., E-mail: leving@post.tau.ac.il [Department of Particle Physics, School of Physics and Astronomy, Raymond and Beverly Sackler Faculty of Exact Science, Tel Aviv University, Tel Aviv, 69978 (Israel); Departemento de Física, Universidad Técnica Federico Santa María, and Centro Científico-Tecnológico de Valparaíso, Avda. Espana 1680, Casilla 110-V, Valparaíso (Chile); Maor, U., E-mail: maor@post.tau.ac.il [Department of Particle Physics, School of Physics and Astronomy, Raymond and Beverly Sackler Faculty of Exact Science, Tel Aviv University, Tel Aviv, 69978 (Israel)

2015-06-30

In this letter we demonstrate that our dipole model is successful in describing inclusive production within the same framework as diffractive physics. We believe that this achievement stems from the fact that our approach incorporates the positive features of the Reggeon approach and CGC/saturation effective theory, for high energy QCD.

Characterization of saturation of CR-39 detector at high alpha-particle fluence

Directory of Open Access Journals (Sweden)

M. El Ghazaly

2018-04-01

Full Text Available The occurrence of saturation in the CR-39 detector reduces and limits its detection dynamic range; nevertheless, this range could be extended using spectroscopic techniques and by measuring the net bulk rate of the saturated CR-39 detector surface. CR-39 detectors were irradiated by 1.5 MeV high alpha-particle fluence varying from 0.06 × 108 to 7.36 × 108 alphas/cm2 from Am-241 source; thereafter, they were etched in a 6.25N NaOH solution at a temperature of 70°C for different durations. Net bulk etch rate measurement of the 1.5 MeV alpha-irradiated CR-39 detector surface revealed that rate increases with increasing etching time and reaches its maximum value at the end of the alpha-particle range. It is also correlated with the alpha-particle fluence. The measurements of UV–Visible (UV–Vis absorbance at 500 and 600 nm reveal that the absorbance is linearly correlated with the fluence of alpha particles at the etching times of 2 and 4 hour. For extended etching times of 6, 10, and 14.5 hour, the absorbance is saturated for fluence values of 4.05 × 108, 5.30 × 108, and 7.36 × 108 alphas/cm2. These new methods pave the way to extend the dynamic range of polymer-based solid state nuclear track detectors (SSNTDs in measurement of high fluence of heavy ions as well as in radiation dosimetry. Keywords: Alpha Particle, Bulk Etch Rate, CR-39 Detector, Saturated Regime, UV–Vis Spectroscopy

Randomised trial of coconut oil, olive oil or butter on blood lipids and other cardiovascular risk factors in healthy men and women.

Science.gov (United States)

Khaw, Kay-Tee; Sharp, Stephen J; Finikarides, Leila; Afzal, Islam; Lentjes, Marleen; Luben, Robert; Forouhi, Nita G

2018-03-06

High dietary saturated fat intake is associated with higher blood concentrations of low-density lipoprotein cholesterol (LDL-C), an established risk factor for coronary heart disease. However, there is increasing interest in whether various dietary oils or fats with different fatty acid profiles such as extra virgin coconut oil may have different metabolic effects but trials have reported inconsistent results. We aimed to compare changes in blood lipid profile, weight, fat distribution and metabolic markers after four weeks consumption of 50 g daily of one of three different dietary fats, extra virgin coconut oil, butter or extra virgin olive oil, in healthy men and women in the general population. Randomised clinical trial conducted over June and July 2017. General community in Cambridgeshire, UK. Volunteer adults were recruited by the British Broadcasting Corporation through their websites. Eligibility criteria were men and women aged 50-75 years, with no known history of cancer, cardiovascular disease or diabetes, not on lipid lowering medication, no contraindications to a high-fat diet and willingness to be randomised to consume one of the three dietary fats for 4 weeks. Of 160 individuals initially expressing an interest and assessed for eligibility, 96 were randomised to one of three interventions; 2 individuals subsequently withdrew and 94 men and women attended a baseline assessment. Their mean age was 60 years, 67% were women and 98% were European Caucasian. Of these, 91 men and women attended a follow-up assessment 4 weeks later. Participants were randomised to extra virgin coconut oil, extra virgin olive oil or unsalted butter and asked to consume 50 g daily of one of these fats for 4 weeks, which they could incorporate into their usual diet or consume as a supplement. The primary outcome was change in serum LDL-C; secondary outcomes were change in total and high-density lipoprotein cholesterol (TC and HDL-C), TC/HDL-C ratio and non

Minnealloy: a new magnetic material with high saturation flux density and low magnetic anisotropy

Science.gov (United States)

Mehedi, Md; Jiang, Yanfeng; Suri, Pranav Kumar; Flannigan, David J.; Wang, Jian-Ping

2017-09-01

We are reporting a new soft magnetic material with high saturation magnetic flux density, and low magnetic anisotropy. The new material is a compound of iron, nitrogen and carbon, α‧-Fe8(NC), which has saturation flux density of 2.8  ±  0.15 T and magnetic anisotropy of 46 kJ m-3. The saturation flux density is 27% higher than pure iron, a widely used soft magnetic material. Soft magnetic materials are very important building blocks of motors, generators, inductors, transformers, sensors and write heads of hard disk. The new material will help in the miniaturization and efficiency increment of the next generation of electronic devices.

Highly porous oil sorbent based on hollow fibers as the interceptor for oil on static and running water

Energy Technology Data Exchange (ETDEWEB)

Dong, Ting [College of Textiles, Donghua University, Shanghai 201620 (China); Cao, Shengbin [College of Textiles, Donghua University, Shanghai 201620 (China); School of Mechanical Engineering, Shanghai Dianji University, Shanghai 201306 (China); Xu, Guangbiao, E-mail: guangbiao_xu@dhu.edu.cn [College of Textiles, Donghua University, Shanghai 201620 (China); Key Laboratory of Textile Science and Technology Ministry of Education, Donghua University, Shanghai 201620 (China)

2016-03-15

Highlights: • Highly porous sorbent was made up of kapok and PET fibers. • The sorbent was prepared by air-laying-bonding method. • The sorbent showed much higher oil sorption capacity than 100% loose kapok fibers. • The sorbent showed high intercepting efficiency to oils on water. • The runing of water significantly accelerated the oil leakage. - Abstract: Highly porous fibrous assembly made by kapok and hollow PET fibers was prepared by the air-laying-bonding method, and used as the interceptor for oils on static and running water. SEM showed that the vast majority of kapok and PET fibers in the assembly was intact and retained their hollow lumens, with the assembly's porosity high to 98.03%. Oil sorption tests exhibited that kapok/PET assembly could absorb 63.00 g/g of vegetable oil and 58.50 g/g of used motor oil, with high oil retention after 24 h dripping. In static condition of oil interception, the two oils started to leak at around 20 min for 10-mm thick kapok/PET wall. The time for that was prolonged with increasing the thickness of kapok/PET wall. After oil breakthrough, continuous oil leaking took place. The typical leakage was divided into three stages in which oils leaked separately in sharply increased rate, reduced rate and finally gently. In running condition, oils leaked in markedly quicker way than that in static condition, with initial leakage of oils shortened to less 6 min when the water ran at 60.35 ml/s. The leakage of oils was considerably accelerated with increasing running rates.

Highly porous oil sorbent based on hollow fibers as the interceptor for oil on static and running water

International Nuclear Information System (INIS)

Dong, Ting; Cao, Shengbin; Xu, Guangbiao

2016-01-01

Highlights: • Highly porous sorbent was made up of kapok and PET fibers. • The sorbent was prepared by air-laying-bonding method. • The sorbent showed much higher oil sorption capacity than 100% loose kapok fibers. • The sorbent showed high intercepting efficiency to oils on water. • The runing of water significantly accelerated the oil leakage. - Abstract: Highly porous fibrous assembly made by kapok and hollow PET fibers was prepared by the air-laying-bonding method, and used as the interceptor for oils on static and running water. SEM showed that the vast majority of kapok and PET fibers in the assembly was intact and retained their hollow lumens, with the assembly's porosity high to 98.03%. Oil sorption tests exhibited that kapok/PET assembly could absorb 63.00 g/g of vegetable oil and 58.50 g/g of used motor oil, with high oil retention after 24 h dripping. In static condition of oil interception, the two oils started to leak at around 20 min for 10-mm thick kapok/PET wall. The time for that was prolonged with increasing the thickness of kapok/PET wall. After oil breakthrough, continuous oil leaking took place. The typical leakage was divided into three stages in which oils leaked separately in sharply increased rate, reduced rate and finally gently. In running condition, oils leaked in markedly quicker way than that in static condition, with initial leakage of oils shortened to less 6 min when the water ran at 60.35 ml/s. The leakage of oils was considerably accelerated with increasing running rates.

Enzymes for Enhanced Oil Recovery (EOR)

Energy Technology Data Exchange (ETDEWEB)

Nasiri, Hamidreza

2011-04-15

enzymes on interactions in the oil/brine/solid system was studied. It was found that enzymes can change the adhesion behavior of the crude oil on glass surfaces from adhesion to non-adhesion when they are added to the brine solution. This was confirmed by contact angle measurements, which showed that contact angles became more water-wet (i.e. decreased) after exposure to enzyme solutions. Possible mechanisms giving rise to these observations, including catalysis of ester hydrolysis and enzyme adsorption, were discussed and tested. An experimental study of changes in oil-water interfacial properties by addition of enzymes and proteins, including measurements of interfacial tension and electrophoretic mobility, has been performed. It was found that the effect of enzymes on oil-water properties is minor compared to their effect on oil-water-solid properties. Their contribution to change interfacial tension between oil and water is not significant while they affect the electrophoretic mobility of emulsified oil in enzyme-brine solution to some extent. Attempts were also made to study changes in both oil and water phase composition after equilibration with enzymes. However, since the chemical composition of crude oil is highly complex, a model oil was used in some of the experiments. The model oil was chosen to be a water insoluble ester (ethyl decanoate) solved in mineral oil in an effort to verify the possible role of catalysis of ester hydrolysis. Dynamic core displacements using sandstone and carbonate rocks were conducted to show the potential of improved oil recovery by enzyme- and combined enzyme-surfactant flooding. Most of the core flooding experiments commenced with water flooding from initial water saturation, Swi, (established with synthetic sea water) which will be referred to as secondary mode displacements. Accordingly, tertiary oil recovery processes were used to describe injection of enzyme and/or enzyme-surfactant solutions from residual oil saturation, Sor

[Study on two preparation methods for beta-CD inclusion compound of four traditional Chinese medicine volatile oils].

Science.gov (United States)

Li, Hailiang; Cui, Xiaoli; Tong, Yan; Gong, Muxin

2012-04-01

To compare inclusion effects and process conditions of two preparation methods-colloid mill and saturated solution-for beta-CD inclusion compound of four traditional Chinese medicine volatile oils and study the relationship between each process condition and volatile oil physical properties and the regularity of selective inclusion of volatile oil components. Volatile oils from Nardostachyos Radix et Rhizoma, Amomi Fructus, Zingiberis Rhizoma and Angelicaesinensis Radix were prepared using two methods in the orthogonal test. These inclusion compounds by optimized processes were assessed and compared by such methods as TLC, IR and scanning electron microscope. Inclusion oils were extracted by steam distillation, and the components found before and after inclusion were analyzed by GC-MS. Analysis showed that new inclusion compounds, but inclusion compounds prepared by the two processes had differences to some extent. The colloid mill method showed a better inclusion effect than the saturated solution method, indicating that their process conditions had relations with volatile oil physical properties. There were differences in the inclusion selectivity of components between each other. The colloid mill method for inclusion preparation is more suitable for industrial requirements. To prepare volatile oil inclusion compounds with heavy gravity and high refractive index, the colloid mill method needs longer time and more water, while the saturated solution method requires higher temperature and more beta-cyclodextrin. The inclusion complex prepared with the colloid mill method contains extended molecular weight chemical composition, but the kinds of components are reduced.

Aerobic microbial enhanced oil recovery

Energy Technology Data Exchange (ETDEWEB)

Torsvik, T. [Univ. of Bergen (Norway); Gilje, E.; Sunde, E.

1995-12-31

In aerobic MEOR, the ability of oil-degrading bacteria to mobilize oil is used to increase oil recovery. In this process, oxygen and mineral nutrients are injected into the oil reservoir in order to stimulate growth of aerobic oil-degrading bacteria in the reservoir. Experiments carried out in a model sandstone with stock tank oil and bacteria isolated from offshore wells showed that residual oil saturation was lowered from 27% to 3%. The process was time dependent, not pore volume dependent. During MEOR flooding, the relative permeability of water was lowered. Oxygen and active bacteria were needed for the process to take place. Maximum efficiency was reached at low oxygen concentrations, approximately 1 mg O{sub 2}/liter.

Comparison Between Oil-mist and Oil-jet Lubrication of High-speed, Small-bore, Angular-contact Ball Bearings

Science.gov (United States)

Pinel, Stanley I.; Signer, Hans R.; Zaretsky, Erwin V.

2001-01-01

Parametric tests were conducted with an optimized 35-mm-bore-angular-contact ball bearing on a high-speed, high-temperature bearing tester. Results from both air-oil mist lubrication and oil-jet lubrication systems used to lubricate the bearing were compared to speeds of 2.5 x 10(exp 6) DN. The maximum obtainable speed with air-oil mist lubrication is 2.5 x 10(exp 6) DN. Lower bearing temperatures and higher power losses are obtained with oil-jet lubrication than with air-oil mist lubrication. Bearing power loss is a direct function of oil flow to the bearing and independent of oil delivery system. For a given oil-flow rate, bearing temperature and power loss increase with increases in speed. Bearing life is an inverse function of temperature, the difference in temperature between the individual bearing ring components, and the resultant elastohydrodynamic (EHD) film thicknesses. Bearing life is independent of the oil delivery system except as it affects temperature. Cage slip increased with increases in speed. Cage slip as high as 7 percent was measured and was generally higher with air-oil mist lubrication than with oil-jet lubrication.

Ultra-broadband nonlinear saturable absorption of high-yield MoS2 nanosheets

Science.gov (United States)

Wei, Rongfei; Zhang, Hang; Hu, Zhongliang; Qiao, Tian; He, Xin; Guo, Qiangbing; Tian, Xiangling; Chen, Zhi; Qiu, Jianrong

2016-07-01

High-yield MoS2 nanosheets with strong nonlinear optical (NLO) responses in a broad near-infrared range were synthesized by a facile hydrothermal method. The observation of saturable absorption, which was excited by the light with photon energy smaller than the gap energy of MoS2, can be attributed to the enhancement of the hybridization between the Mo d-orbital and S p-orbital by the oxygen incorporation into MoS2. High-yield MoS2 nanosheets with high modulation depth and large saturable intensity generated a stable, passively Q-switched fiber laser pulse at 1.56 μm. The high output power of 1.08 mW can be attained under a very low pump power of 30.87 mW. Compared to recently reported passively Q-switched fiber lasers utilizing exfoliated MoS2 nanosheets, the efficiency of the laser for our passive Q-switching operation is larger and reaches 3.50%. This research may extend the understanding on the NLO properties of MoS2 and indicate the feasibility of the high-yield MoS2 nanosheets to passively Q-switched fiber laser effectively at low pump strengths.

Beneficial nutritional properties of olive oil: implications for postprandial lipoproteins and factor VII.

Science.gov (United States)

Williams, C M

2001-08-01

Previous research concerning protective cardiovascular properties of olive oil has focussed on the beneficial consequences on blood cholesterol levels of substituting dietary saturated fatty acids with oleic acid. Despite evidence implicating raised circulating triglycerides in the postprandial state in the pathogenesis of atherosclerosis and thrombosis, little research had been conducted to investigate effects of monounsaturated fatty acids on postprandial events. In a case control study of southern (n = 30) versus northern European (n = 30) men, significant differences in postprandial triglyceride and apolipoprotein (apo) B-48 response were observed, with evidence of attenuated and potentially beneficial responses in the Southern Europeans. In a randomised controlled study manufactured foods typical of the Northern European food culture, were used to deliver diets rich in either saturated or monounsaturated fatty acids (from olive oil). During the period of the olive oil enriched diet, LDL-cholesterol levels were 15% lower (p factor VII, as well as the production of factor VII antigen, was reduced on the olive oil diet. The study demonstrated significant improvements in biomarkers for cardiovascular disease in subjects osed to high olive oil diets (Southern Europeans) or transferred to such diets in the short term (Northern European volunteers). The study produced novel findings with respect to potential mechanisms by which diets high in monounsaturated fatty acids (MUFA) can reduce population risk of cardiovascular disease.

Detection of argan oil adulteration with vegetable oils by high-performance liquid chromatography-evaporative light scattering detection.

Science.gov (United States)

Salghi, Rachid; Armbruster, Wolfgang; Schwack, Wolfgang

2014-06-15

Triacylglycerol profiles were selected as indicator of adulteration of argan oils to carry out a rapid screening of samples for the evaluation of authenticity. Triacylglycerols were separated by high-performance liquid chromatography-evaporative light scattering detection. Different peak area ratios were defined to sensitively detect adulteration of argan oil with vegetable oils such as sunflower, soy bean, and olive oil up to the level of 5%. Based on four reference argan oils, mean limits of detection and quantitation were calculated to approximately 0.4% and 1.3%, respectively. Additionally, 19 more argan oil reference samples were analysed by high-performance liquid chromatography-refractive index detection, resulting in highly comparative results. The overall strategy demonstrated a good applicability in practise, and hence a high potential to be transferred to routine laboratories. Copyright © 2013 Elsevier Ltd. All rights reserved.

Comparative effects of dietary corn oil, safflower oil, fish oil and palm oil on metabolism of ethanol and carnitine in the rat.

Science.gov (United States)

Sachan, Dileep S; Yatim, Ayub M; Daily, James W

2002-06-01

This study was launched to determine comparative effects of corn oil (CO), safflower oil (SO), fish oil (FO) and palm oil (PO) on carnitine status and ethanol metabolism in rats. Twenty-four male Sprague-Dawley rats (300 g bw) were randomly divided into four groups (n = 6) and fed a semisynthetic diets containing fat as oils listed above. Blood and 24 hour urine samples were collected before and after dietary treatment and acute ethanol administration. Samples were analyzed for blood-ethanol concentration (BEC) and carnitine species. The diets containing FO and PO retarded ethanol metabolism compared to the diets containing CO and SO. The effect of these dietary fats on carnitine species in plasma and urine was varied before and after dietary treatment and following a single oral ethanol dose. The liver carnitine content was higher in the PO group after dietary and ethanol treatment. It is concluded that attenuation of ethanol clearance was related to unique fatty acid makeup of the oils that in part may be attributed to the composite ratio of saturated to unsaturated fatty acids in the oils.

Optimization of pressurized liquid extraction (PLE) for rapid determination of mineral oil saturated (MOSH) and aromatic hydrocarbons (MOAH) in cardboard and paper intended for food contact.

Science.gov (United States)

Moret, Sabrina; Sander, Maren; Purcaro, Giorgia; Scolaro, Marianna; Barp, Laura; Conte, Lanfranco S

2013-10-15

Packaging can represent a primary source of food contamination with mineral oil saturated hydrocarbons (MOSH) and aromatic hydrocarbons (MOAH), especially when recycled cardboard or mineral oil based printing inks are used. A pressurized liquid extraction (PLE) method, followed by on-line LC-GC analysis, has been optimized for rapid mineral oil determination in cardboard and paper samples. The proposed method involves extraction with hexane (2 cycles) at 60°C for 5 min, and allows for the processing of up to 6 samples in parallel with minimal sample manipulation and solvent consumption. It gave good repeatability (coefficient of variation lower than 5%) and practically quantitative extraction yield (less than 2% of the total contamination found in a third separate cycle). The method was applied to different cardboards and paper materials intended for food contact. Results obtained were similar to those obtained by applying classical solvent extraction with hexane/ethanol 1:1 (v/v) as described by Lorenzini et al. [20]. Copyright © 2013 Elsevier B.V. All rights reserved.

Isothermal decomposition of Baltic oil shale

Energy Technology Data Exchange (ETDEWEB)

Aarna, A Ya

1955-01-01

Heating oil shale at 300/sup 0/ to 440/sup 0/C yields a primary tar. Longer heating, regardless of temperature, results in the formation of heavier tar fractions. Higher temperatures tend to increase the middle and high-boiling fractions and to increase the concentration of unsaturated hydrocarbons at the expense of saturated hydrocarbons. Phenols appear, even at lower heating temperatures, indicating that aromatic structures are present or generated during the process.

Extraction of essential oils from Algerian myrtle leaves using instant controlled pressure drop technology.

Science.gov (United States)

Berka-Zougali, Baya; Hassani, Aicha; Besombes, Colette; Allaf, Karim

2010-10-01

In the present work, the new extraction process of Détente Instantanée Contrôlée DIC (French, for instant controlled pressure drop) was studied, developed, quantitatively and qualitatively compared to the conventional hydrodistillation method for the extraction of essential oils from Algerian myrtle leaves. DIC was used as a thermomechanical treatment, DIC subjecting the product to a high-pressure saturated steam. The DIC cycle ends with an abrupt pressure drop towards vacuum, and this instantly leads to an autovaporization of myrtle volatile compounds. An immediate condensation in the vacuum tank produced a micro-emulsion of water and essential oils. Thus, an ultra-rapid cooling of residual leaves occurred, precluding any thermal degradation. An experimental protocol was designed with 3 independent variables: saturated steam pressure between 0.1 and 0.6 MPa, resulting in a temperature between 100 and 160°C, a total thermal processing time between 19 and 221 s, and between 2 and 6 DIC cycles. The essential oils yield was defined as the main dependent variable. This direct extraction gave high yields and high quality essential oil, as revealed by composition and antioxidant activity (results not shown). After this treatment, the myrtle leaves were recovered and hydrodistilled in order to quantify the essential oil content in residual DIC-treated samples. Scanning electron microscope (SEM) showed some modification of the structure with a slight destruction of cell walls after DIC treatment. Copyright © 2010 Elsevier B.V. All rights reserved.

Capillary pressure - saturation relations in quartz and carbonate sands: Limitations for correlating capillary and wettability influences on air, oil, and supercritical CO2 trapping

Science.gov (United States)

Tokunaga, T. K.; Wang, S.; Wan, J.; Dong, W.; Kim, Y.

2016-12-01

Capillary pressure (Pc) - saturation (Sw) relations are essential for predicting equilibrium and flow of immiscible fluid pairs in soils and deeper geologic formations. In systems that are difficult to measure, behavior is often estimated based on capillary scaling of easily measured Pc-Sw relations (e.g., air-water, and oil-water), yet the reliability of such approximations needs to be examined. In this study, seventeen sets of brine drainage and imbibition curves were measured with air-brine, decane-brine, and supercritical (sc) CO2-brine in homogeneous quartz and carbonate sands, using porous plate systems under ambient (0.1 MPa, 23 °C) and reservoir (12.0 MPa, 45 °C) conditions. Comparisons between these measurements showed significant differences in residual nonwetting phase saturation, Snw,r. Through applying capillary scaling, changes in interfacial properties were indicated, particularly wettability. With respect to the residual trapping of the nonwetting phases, Snwr, CO2 > Snwr, decane > Snwr, air. Decane-brine and scCO2-brine Pc-Sw curves deviated significantly from predictions assuming hydrophilic interactions. Moreover, neither the scaled capillary behavior nor Snw,r for scCO2-brine were well represented by decane-brine, apparently because of differences in wettability and viscosities, indicating limitations for using decane (and other organic liquids) as a surrogate fluid in studies intended to apply to geological carbon sequestration. Thus, challenges remain in applying scaling for predicting capillary trapping and multiphase displacement processes across such diverse fields as vadose zone hydrology, enhanced oil recovery, and geologic carbon sequestration.

Effective use of complex secondary recovery methods in operation of small oil fields

Energy Technology Data Exchange (ETDEWEB)

Ibragimov, M R; Akulov, V P; Khutorov, A M

1966-11-01

The North Sokhs Field, located in the southern part of the Fergen depression, is composed of many horizons and has an anticlinal structure. The eighth horizon has highest oil saturation, with an average porosity of 17% and permeability of 80 md. Poor oil recovery was initially obtained from this horizon because the basic producing mechanism was solution gas drive. In 1961, when reservoir pressure was 94 kg/cmU2D and gas factor was 700-800mU3D/ton, pressure maintenance was initiated by injection of gas to the structure. Gas injection improved oil recovery considerably; however, high gas-oil ratios appeared in several wells. Next, peripheral water injection was started, and continued simultaneously with gas injection. The simultaneous injection of gas and water almost doubled oil production. Because of continued, high produced gas/oil ratios, gas injection was eventually discontinued, while water injection was continued. Water injection is building up reservoir pressure and improving oil recovery.

Enhanced Oil Recovery: Aqueous Flow Tracer Measurement

Energy Technology Data Exchange (ETDEWEB)

Joseph Rovani; John Schabron

2009-02-01

A low detection limit analytical method was developed to measure a suite of benzoic acid and fluorinated benzoic acid compounds intended for use as tracers for enhanced oil recovery operations. Although the new high performance liquid chromatography separation successfully measured the tracers in an aqueous matrix at low part per billion levels, the low detection limits could not be achieved in oil field water due to interference problems with the hydrocarbon-saturated water using the system's UV detector. Commercial instrument vendors were contacted in an effort to determine if mass spectrometry could be used as an alternate detection technique. The results of their work demonstrate that low part per billion analysis of the tracer compounds in oil field water could be achieved using ultra performance liquid chromatography mass spectrometry.

Effect of Euterpe oleracea Mart. (Açaí) Oil on Dyslipidemia Caused by Cocos nucifera L. Saturated Fat in Wistar Rats.

Science.gov (United States)

Faria E Souza, Belmira S; Carvalho, Helison O; Taglialegna, Talisson; Barros, Albenise Santana A; da Cunha, Edilson Leal; Ferreira, Irlon Maciel; Keita, Hady; Navarrete, Andres; Carvalho, José Carlos Tavares

2017-09-01

Dyslipidemia is caused by disturbances in lipid metabolism that lead to chronic elevations of serum lipids, especially low-density lipoprotein (LDL)-cholesterol and triglycerides, increasing the risk of metabolic syndrome, obesity, diabetes, atherogenic processes, and cardiovascular diseases. The oil from the fruits of Euterpe oleracea (OFEO) is rich in unsaturated fatty acids with potential for treating alterations in lipid metabolism. In this study, we aimed to investigate the effect of OFEO on hyperlipidemia induced by Cocos nucifera L. saturated fat (GSC) in Wistar rats. Chromatographic profile showed that unsaturated fatty acids account for 66.08% in OFEO, predominately oleic acid (54.30%), and saturated fatty acids (palmitic acid 31.6%) account for 33.92%. GSC-induced dyslipidemia resulted in an increase in total cholesterol, LDL-cholesterol, triglycerides, glucose, and liver and abdominal fat, as well as atherogenic processes in the thoracic aorta. OFEO treatment did not reduce hypertriglyceridemia, but did reduce total cholesterol and LDL-cholesterol, thus contributing to the antiatherogenic action of OFEO. OFEO treatment inhibited the formation of atheromatous plaques in the vascular endothelium of the treated rats, as well as those who were treated with simvastatin. The results obtained suggest that OFEO has an antiatherogenic effect in a rat model of dyslipidemia.

Discrimination of Pulp Oil and Kernel Oil from Pequi (Caryocar brasiliense) by Fatty Acid Methyl Esters Fingerprinting, Using GC-FID and Multivariate Analysis

NARCIS (Netherlands)

Faria-Machado, A.F.; Tres, Alba; Ruth, Van S.M.; Antoniassi, Rosemar; Junqueira, N.T.V.; Lopes, P.S.N.; Bizzo, H.R.

2015-01-01

Pequi is an oleaginous fruit whose edible oil is composed mainly by saturated and monounsaturated fatty acids. The biological and nutritional properties of pequi oil are dependent on its composition, which can change according to the oil source (pulp or kernel). There is little data in the

Fortum Oil and Gas 2000: Exceptionally high price of crude oil and strong refining margins

International Nuclear Information System (INIS)

Ropponen, V.-M.

2001-01-01

Fortum intends to be an active player in the structural reorganization of the oil business by utilizing its niche position in oil refining. Fortum produces sophisticated motor fuel components, which it uses in its reformulated gasolines and sells and exports to other oil companies, even to highly demanding markets in California. The increase in the price of crude oil considerably improved the results of Oil and Gas Upstream. Similarly, an improvement in the refining margin, as well as profitable shipping operations and a strong demand for gasoline components, boosted the results of Oil Refining and Marketing. (orig.)

Abdominal obesity and type 2 diabetes in Asian Indians: dietary strategies including edible oils, cooking practices and sugar intake.

Science.gov (United States)

Gulati, S; Misra, A

2017-07-01

Obesity and type 2 diabetes are increasing in rural and urban regions of South Asia including India. Pattern of fat deposition in abdomen, ectopic fat deposition (liver, pancreas) and also low lean mass are contributory to early-onset insulin resistance, dysmetabolic state and diabetes in Asian Indians. These metabolic perturbations are further exacerbated by changing lifestyle, diet urbanization, and mechanization. Important dietary imbalances include increasing use of oils containing high amount of trans fatty acids and saturated fats (partially hydrogenated vegetable oil, palmolein oil) use of deep frying method and reheating of oils for cooking, high intake of saturated fats, sugar and refined carbohydrates, low intake of protein, fiber and increasing intake of processed foods. Although dietary intervention trials are few; the data show that improving quality of carbohydrates (more complex carbohydrates), improving fat quality (more monounsaturated fatty acids and omega 3 polyunsaturated fatty acids) and increasing protein intake could improve blood glucose, serum insulin, lipids, inflammatory markers and hepatic fat, but more studies are needed. Finally, regulatory framework must be tightened to impose taxes on sugar-sweetened beverages, oils such as palmolein, and dietary fats and limit trans fats.

Fabrication high-purity Fe nanochains with near theoretical limit value of saturation magnetization of bulk Fe

Energy Technology Data Exchange (ETDEWEB)

Bian, Erkang [Henan University, Key Laboratory for Special Functional Materials of Ministry of Education (China); Xu, Yanling [Henan University, The Audit Department (China); Lou, Shiyun, E-mail: lousy@henu.edu.cn [Henan University, Key Laboratory for Special Functional Materials of Ministry of Education (China); Fu, Yunlong, E-mail: yunlongfu@dns.sxnu.edu.cn [Shanxi Normal University, School of Chemistry and Material Science (China); Zhou, Shaomin, E-mail: smzhou@henu.edu.cn [Henan University, Key Laboratory for Special Functional Materials of Ministry of Education (China)

2016-11-15

High-yield purity chain-like one-dimensional nanostructures consisting of single crystal Fe nanoparticles have been produced by using solution dispersion approach. Room temperature magnetic measurement shows that the as-fabricated Fe nanochains are ferromagnetic with a high saturation magnetization (203 emu/g) whereas the nanoparticles are single magnetic domains, which indicate that the as-synthesized products have superparamagnetism behavior with the saturation magnetization of about 28 emu/g. Maybe this results from the directional alignment of the nanoparticles. The excellent characteristic may have led to the potential applications in spin filtering, high density magnetic recording, and nanosensors.

Study on high power ultraviolet laser oil detection system

Science.gov (United States)

Jin, Qi; Cui, Zihao; Bi, Zongjie; Zhang, Yanchao; Tian, Zhaoshuo; Fu, Shiyou

2018-03-01

Laser Induce Fluorescence (LIF) is a widely used new telemetry technology. It obtains information about oil spill and oil film thickness by analyzing the characteristics of stimulated fluorescence and has an important application in the field of rapid analysis of water composition. A set of LIF detection system for marine oil pollution is designed in this paper, which uses 355nm high-energy pulsed laser as the excitation light source. A high-sensitivity image intensifier is used in the detector. The upper machine sends a digital signal through a serial port to achieve nanoseconds range-gated width control for image intensifier. The target fluorescence spectrum image is displayed on the image intensifier by adjusting the delay time and the width of the pulse signal. The spectral image is coupled to CCD by lens imaging to achieve spectral display and data analysis function by computer. The system is used to detect the surface of the floating oil film in the distance of 25m to obtain the fluorescence spectra of different oil products respectively. The fluorescence spectra of oil products are obvious. The experimental results show that the system can realize high-precision long-range fluorescence detection and reflect the fluorescence characteristics of the target accurately, with broad application prospects in marine oil pollution identification and oil film thickness detection.

Cross-phase modulation instability in optical fibres with exponential saturable nonlinearity and high-order dispersion

International Nuclear Information System (INIS)

Xian-Qiong, Zhong; An-Ping, Xiang

2010-01-01

Utilizing the linear-stability analysis, this paper analytically investigates and calculates the condition and gain spectra of cross-phase modulation instability in optical fibres in the case of exponential saturable nonlinearity and high-order dispersion. The results show that, the modulation instability characteristics here are similar to those of conventional saturable nonlinearity and Kerr nonlinearity. That is to say, when the fourth-order dispersion has the same sign as that of the second-order one, a new gain spectral region called the second one which is far away from the zero point may appear. The existence of the exponential saturable nonlinearity will make the spectral width as well as the peak gain of every spectral region increase with the input powers before decrease. Namely, for every spectral regime, this may lead to a unique value of peak gain and spectral width for two different input powers. In comparison with the case of conventional saturable nonlinearity, however, when the other parameters are the same, the variations of the spectral width and the peak gain with the input powers will be faster in case of exponential saturable nonlinearity. (classical areas of phenomenology)

A randomized study of coconut oil versus sunflower oil on cardiovascular risk factors in patients with stable coronary heart disease.

Science.gov (United States)

Vijayakumar, Maniyal; Vasudevan, D M; Sundaram, K R; Krishnan, Sajitha; Vaidyanathan, Kannan; Nandakumar, Sandya; Chandrasekhar, Rajiv; Mathew, Navin

2016-01-01

Coronary artery disease (CAD) and its pathological atherosclerotic process are closely related to lipids. Lipids levels are in turn influenced by dietary oils and fats. Saturated fatty acids increase the risk for atherosclerosis by increasing the cholesterol level. This study was conducted to investigate the impact of cooking oil media (coconut oil and sunflower oil) on lipid profile, antioxidant mechanism, and endothelial function in patients with established CAD. In a single center randomized study in India, patients with stable CAD on standard medical care were assigned to receive coconut oil (Group I) or sunflower oil (Group II) as cooking media for 2 years. Anthropometric measurements, serum, lipids, Lipoprotein a, apo B/A-1 ratio, antioxidants, flow-mediated vasodilation, and cardiovascular events were assessed at 3 months, 6 months, 1 year, and 2 years. Hundred patients in each arm completed 2 years with 98% follow-up. There was no statistically significant difference in the anthropometric, biochemical, vascular function, and in cardiovascular events after 2 years. Coconut oil even though rich in saturated fatty acids in comparison to sunflower oil when used as cooking oil media over a period of 2 years did not change the lipid-related cardiovascular risk factors and events in those receiving standard medical care. Copyright © 2015 Cardiological Society of India. Published by Elsevier B.V. All rights reserved.

Composition of fatty acids in selected vegetable oils

Directory of Open Access Journals (Sweden)

Helena Frančáková

2015-12-01

Full Text Available Plant oils and fats are important and necessary components of the human nutrition. They are energy source and also contain fatty acids - compounds essential for human health. The aim of this study was to evaluate nutritional quality of selected plant oil - olive, rapeseed, pumpkin, flax and sesame; based on fatty acid composition in these oils. Fatty acids (MUFA, PUFA, SFA were analyzed chromatography using system Agilent 6890 GC, injector multimode, detector FID. The highest content of saturated fatty acids was observed in pumpkinseed oil (19.07%, the lowest content was found in rapeseed oil (7.03%, with low level of palmitic and stearic acids and high level of behenic acid (0.32% among the evaluated oils. The highest content of linoleic acid was determined in pumpkinseed (46.40% and sesame oil (40.49%; in these samples was also found lowest content of α-linolenic acid. These oils have important antioxidant properties and are not subject to oxidation. The richest source of linolenic acid was flaxseed oil which, which is therefore more difficult to preserve and process in food industry. In olive oil was confirmed that belongs to the group of oils with a predominantly monosaturated oleic acid (more than 70% and a small amount of polysaturated fatty acid. The most commonly used rapeseed oil belongs to the group of oils with the medium content of linolenic acid (8.76%; this oil also showed a high content of linoleic acid (20.24%. The group of these essentially fatty acids showed a suitable ratio ∑n3/n6 in the rapessed oil (0.44.

Determinants of edible oil choice by households in Tamil Nadu, India.

Science.gov (United States)

Govindaraj, Gurrappa Naidu; Suryaprakash, Satrasala

2013-01-01

This study investigated the major determinants that influence the choice of edible oils by households across geographical zones in Tamil Nadu state, India. The primary data from 1,000 sample households were collected using a structured pre-tested questionnaire. Multinomial logit model was fitted for determining the factors. The results revealed that education, income, and households with a history of health problems were the important determinants that influenced the choice of low-saturated-fat oils, whereas the larger size households and weaker section households preferred low-priced palm oil. Income and education levels in Tamil Nadu state surged ahead in recent years. In consonance to these changes the nontraditional low-saturated fat containing sunflower oil demand will increase in many folds in coming years. Hence, besides traditional oils, sunflower oil production has to be stepped up on "mission mode" through appropriate production programs to meet the present and future edible oil demand domestically.

Physico-Chemical Properties of the Oils and Fat from Crotalaria cleomifolia Seeds

International Nuclear Information System (INIS)

Noor Wini Mazlan; Ikram Muhd Said

2011-01-01

The seeds of C. cleomifolia (locally known as kacang hantu) collected along Simpang Pulai - Berinchang Road, Cameron Highlands, was defatted with hexane and the resulting oil was analysed for their physico-chemical properties. The percentage yield of the oil was calculated as 5.3 %. The acid value (1.2 %), iodine value (85), peroxide value (0.6), saponification value (192.0) and unsaponifiable matter (2.3 %) were determined to assess the quality of the oil. The physico-chemical characterisation showed that C. cleomifolia seeds oil is unsaturated semi-drying oil, with high saponification and acidic values. The fatty acid composition of C. cleomifolia seed oil was determined by Gas Chromatography and Gas Chromatography-Mass Spectrometry (ToF). The seed oil of C. cleomifolia contained linoleic acid (57.59 %) and palmitic acid (5.07 %), the most abundant unsaturated and saturated fatty acids, respectively. The polyunsaturated triacylglycerol (TAG) in C. cleomifolia seed oil determined by reverse phase High performance Liquid Chromatography; contained as PLL (18.04 %) followed by POL + SLL (11.92 %), OOL (7.04 %) and PLLn (6.31 %). The melting and cooling point of the oil were 16.22 degree Celsius and -33.54 degree Celsius, respectively. (author)

On the water saturation calculation in hydrocarbon sandstone reservoirs

Energy Technology Data Exchange (ETDEWEB)

Stalheim, Stein Ottar

2002-07-01

The main goal of this work was to identify the most important uncertainty sources in water saturation calculation and examine the possibility for developing new S{sub w} - equations or possibility to develop methods to remove weaknesses and uncertainties in existing S{sub w} - equations. Due to the need for industrial applicability of the equations we aimed for results with the following properties: The accuracy in S{sub w} should increase compared with existing S{sub w} - equations. The equations should be simple to use in petrophysical evaluations. The equations should be based on conventional logs and use as few as possible input parameters. The equations should be numerical stable. This thesis includes an uncertainty and sensitivity analysis of the most common S{sub w} equations. The results are addressed in chapter 3 and were intended to find the most important uncertainty sources in water saturation calculation. To increase the knowledge of the relationship between R{sub t} and S{sub w} in hydrocarbon sandstone reservoirs and to understand how the pore geometry affects the conductivity (n and m) of the rock a theoretical study was done. It was also an aim to examine the possibility for developing new S{sub w} - equations (or investigation an effective medium model) valid inhydrocarbon sandstone reservoirs. The results are presented in paper 1. A new equation for water saturation calculation in clean sandstone oil reservoirs is addressed in paper 2. A recommendation for best practice of water saturation calculation in non water wet formation is addressed in paper 3. Finally a new equation for water saturation calculation in thinly interbedded sandstone/mudstone reservoirs is presented in paper 4. The papers are titled: 1) Is the saturation exponent n a constant. 2) A New Model for Calculating Water Saturation In 3) Influence of wettability on water saturation modeling. 4) Water Saturation Calculations in Thinly Interbedded Sandstone/mudstone Reservoirs. A

Effect of high saturated free fatty acids feeding on progression of renal failure in rat model of experimental nephrotoxicity

Directory of Open Access Journals (Sweden)

Zaid O. Ibraheem

2012-02-01

Full Text Available The current study evaluates the impact of high saturated fat feeding in rat model of experimental nephrotoxicity induced by gentamicin. Sprague-Dawley rats weighing 200 g were randomized into four groups; the first one received the standard rodents chow for 8 weeks and was treated as control, the second group (HFDreceived an experimental high fat diet rich in palm kernel oil (40% of Calories as fat for the same period. The third group (HFDG was given 80 mg/kg (body weight/day gentamicin sulphate intraperitoneally during the last 24 days of the feeding period while the fourth group was given gentamicin as above along with the standard rodents chow. Renal function was assessed through measuring serum creatinine, creatinine clearance and absolute and fractional excretion of both sodium and potassium. At the end, rats underwent a surgical procedure for blood pressure measurement. Renal function study showed a stronger nephrotoxicity for HFDG group. Hypertension was observed in HFD group while the pressure declined after gentamicin co-administration. Overall, changing the feeding behavior toward using more SAFFAs for rats injected with gentamicin promotes the progression of renal failure.

A Saponification Method for Chlorophyll Removal from Microalgae Biomass as Oil Feedstock

Directory of Open Access Journals (Sweden)

Tao Li

2016-09-01

Full Text Available Microalgae oil is an optimal feedstock for nutraceutical, pharmaceutical and biodiesel production, but its high levels of chlorophyll limit its large-scale application. To date, few effective approaches have been developed to remove chlorophyll from microalgae oil. The main purpose of this study was to present a preprocessing method of algae oil feedstock (Scenedesmus to remove chlorophyll by saponification. The results showed that 96% of chlorophyll in biomass was removed. High quality orange transparent oil could be extracted from the chlorophyll reduced biomass. Specifically, the proportion of neutral lipids and saturation levels of fatty acids increased, and the pigments composition became carotenoids-based. The critical parameters of chlorophyll reduced biodiesel conformed to the standards of the USA, China and EU. Sodium copper chlorophyllin could be prepared from the bleaching effluent. The results presented herein offer a useful pathway to improve the quality of microalgae oil and reduce the cost of microalgae biodiesel.

A Saponification Method for Chlorophyll Removal from Microalgae Biomass as Oil Feedstock

Science.gov (United States)

Li, Tao; Xu, Jin; Wu, Hualian; Wang, Guanghua; Dai, Shikun; Fan, Jiewei; He, Hui; Xiang, Wenzhou

2016-01-01

Microalgae oil is an optimal feedstock for nutraceutical, pharmaceutical and biodiesel production, but its high levels of chlorophyll limit its large-scale application. To date, few effective approaches have been developed to remove chlorophyll from microalgae oil. The main purpose of this study was to present a preprocessing method of algae oil feedstock (Scenedesmus) to remove chlorophyll by saponification. The results showed that 96% of chlorophyll in biomass was removed. High quality orange transparent oil could be extracted from the chlorophyll reduced biomass. Specifically, the proportion of neutral lipids and saturation levels of fatty acids increased, and the pigments composition became carotenoids-based. The critical parameters of chlorophyll reduced biodiesel conformed to the standards of the USA, China and EU. Sodium copper chlorophyllin could be prepared from the bleaching effluent. The results presented herein offer a useful pathway to improve the quality of microalgae oil and reduce the cost of microalgae biodiesel. PMID:27618070

A Saponification Method for Chlorophyll Removal from Microalgae Biomass as Oil Feedstock.

Science.gov (United States)

Li, Tao; Xu, Jin; Wu, Hualian; Wang, Guanghua; Dai, Shikun; Fan, Jiewei; He, Hui; Xiang, Wenzhou

2016-09-07

Microalgae oil is an optimal feedstock for nutraceutical, pharmaceutical and biodiesel production, but its high levels of chlorophyll limit its large-scale application. To date, few effective approaches have been developed to remove chlorophyll from microalgae oil. The main purpose of this study was to present a preprocessing method of algae oil feedstock (Scenedesmus) to remove chlorophyll by saponification. The results showed that 96% of chlorophyll in biomass was removed. High quality orange transparent oil could be extracted from the chlorophyll reduced biomass. Specifically, the proportion of neutral lipids and saturation levels of fatty acids increased, and the pigments composition became carotenoids-based. The critical parameters of chlorophyll reduced biodiesel conformed to the standards of the USA, China and EU. Sodium copper chlorophyllin could be prepared from the bleaching effluent. The results presented herein offer a useful pathway to improve the quality of microalgae oil and reduce the cost of microalgae biodiesel.

Rational synthesis of zerovalent iron/bamboo charcoal composites with high saturation magnetization

Science.gov (United States)

Mingshan Wu; Jianfeng Ma; Zhiyong Cai; Genlin Tian; Shumin Yang; Youhong Wang; Xing' e Liu

2015-01-01

The synthesis of magnetic biochar composites is a major new research area in advanced materials sciences. A series of magnetic bamboo charcoal composites (MBC800, MBC1000 and MBC1200) with high saturation magnetization (Ms) was fabricated in this work by mixing bamboo charcoal powder with an aqueous ferric chloride solution and subsequently...

Palm oil and human health. Meeting report of NFI: Nutrition Foundation of Italy symposium.

Science.gov (United States)

Marangoni, Franca; Galli, Claudio; Ghiselli, Andrea; Lercker, Giovanni; La Vecchia, Carlo; Maffeis, Claudio; Agostoni, Carlo; Ballardini, Donatella; Brignoli, Ovidio; Faggiano, Pompilio; Giacco, Rosalba; Macca, Claudio; Magni, Paolo; Marelli, Giuseppe; Marrocco, Walter; Miniello, Vito Leonardo; Mureddu, Gian Francesco; Pellegrini, Nicoletta; Stella, Roberto; Troiano, Ersilia; Verduci, Elvira; Volpe, Roberto; Poli, Andrea

2017-09-01

The use of palm oil by the food industry is increasingly criticized, especially in Italy, for its purported negative effects on human health and environment. This paper summarizes the conclusions of a Symposium on this topic, gathered by the Nutrition Foundation of Italy, among experts representing a number of Italian Medical and Nutritional Scientific Societies. Toxicological and environmental issues were not considered. Participants agreed that: no evidence does exist on the specific health effects of palm oil consumption as compared to other saturated fatty acids-rich fats; the stereospecific distribution of saturated fatty acids in the triacylglycerol molecule of palm oil limits their absorption rate and metabolic effects; in agreement with International guidelines, saturated fatty acids intake should be kept palm oil consumption on human health (and specifically on CVD or cancer risk) can be foreseen.

Pediatric Age Palm Oil Consumption.

Science.gov (United States)

Di Genova, Lorenza; Cerquiglini, Laura; Penta, Laura; Biscarini, Anna; Esposito, Susanna

2018-04-01

Palm oil is widely used in the food industry for its chemical/physical properties, low cost and wide availability. Its widespread use has provoked an intense debate about whether it is a potential danger to human health. In a careful review of the scientific literature, we focused on nutritional characteristics and health effects of the use of palm oil with regards to children, seeking to determine whether there is evidence that justifies fears about the health effects of palm oil. Our review showed that palm oil represents a significant source of saturated fatty acids, to which scientific evidence attributes negative health effects when used in excess, especially with regards to cardiovascular diseases. However, to date, there is no evidence about the harmful effects of palm oil on the health of children. Nevertheless, palm oil has possible ill health effects linked to its composition of fatty acids: its consumption is not correlated to risk factors for cardiovascular diseases in young people with a normal weight and cholesterol level; the elderly and patients with dyslipidaemia or previous cardiovascular events or hypertension are at a greater risk. Therefore, the matter is not palm oil itself but the fatty-acid-rich food group to which it belongs. The most important thing is to consume no more than 10% of saturated fatty acids, regardless of their origin and regardless of one's age. Correct information based on a careful analysis of the scientific evidence, rather than a focus on a singular presumed culprit substance, should encourage better lifestyles.

Microbial ecology of a crude oil contaminated aquifer

Science.gov (United States)

Bekins, B.A.; Cozzarelli, I.M.; Warren, E.; Godsy, E.M.

2002-01-01

Detailed microbial analyses of a glacial outwash aquifer contaminated by crude oil provide insights into the pattern of microbial succession from iron reducing to methanogenic in the anaerobic portion of the contaminant plume. We analysed sediments from this area for populations of aerobes, iron reducers, fermenters and methanogens, using the most probable number method. On the basis of the microbial data the anaerobic area can be divided into distinct physiological zones dominated by either iron-reducers or a consortium of fermenters and methanogens. Chemistry and permeability data show that methanogenic conditions develop first in areas of high hydrocarbon flux. Thus, we find methanogens both in high permeability horizons and also where separate-phase crude oil is present in either the saturated or unsaturated zone. Microbial numbers peak at the top of the separate-phase oil suggesting that growth is most rapid in locations with access to both hydrocarbons and nutrients infiltrating from the surface.

Movement of gasified oil in an infinite stratum drained by a single well

Energy Technology Data Exchange (ETDEWEB)

Tomel' gas, V A

1965-01-01

This article presents a method of calculating the flow of gas and oil into a well, which drains a reservoir by the solution drive mechanism. The following conditions are assumed: (1) Initially, an infinite homogeneous reservoir is saturated with oil above the bubble point; (2) the well draining the reservoir is operated at constant pressure, below the bubble point; and (3) the reservoir contains 2 zones; the zone fartherest from the well contains only oil at a pressure above the bubble point, while the zone nearest the well contains both oil and gas. The pressure and oil saturation gradients around the well are calculated for a variety of conditions, and the results are shown graphically. As pressure drawdown increases, oil production increases and the gas factor at first decreases and then increases rapidly.

Effect of lithological composition of oil reservoirs on oil production by a hot agent

Energy Technology Data Exchange (ETDEWEB)

Abbasov, A A; Kasimov, Sh A

1965-01-01

Several small-scale experiments were performed to determine the effect of steam on oil recovery and on permeability of water-sensitive clay-containing cores. Steam has 2 contradictory actions on oil recovery - (1) steam increases temperature and decreases viscosity of the oil, which aids oil recovery; and (2) steam hydrates and swells clays, which reduces permeability and hinders oil recovery. The oil-recovery experiments were carried out with consolidated cores containing 0, 10, and 22% clay, saturated with water and 28 cp crude oil; superheated steam at 125-300$C was used. The following conclusions were made from the experimental results: (1) oil recovery decreased as clay content of cores increased; however, at all temperatures steam recovered more oil than cold water did. (2) As steam temperature increases, oil recovery reaches a maximum, then decreases. The temperature at which oil recovery begins to decrease depends on core clay content; the higher the clay content, the lower this temperature. (3) Irrespective of whether a reservoir contains clay or not, oil recovery is considerably greater with steam than with water.

Dietary oils, serum lipoproteins, and coronary heart disease.

NARCIS (Netherlands)

Katan, M.B.; Zock, P.L.; Mensink, R.P.

1995-01-01

Variable amounts of olive oil rather than hard fats were used in classic Mediterranean diets. We review the effects of replacing hard fats with olive oils or starchy foods on blood lipoprotein concentrations. The saturated fatty acids lauric, myristic, and palmitic acids raise both low-density

Two-phase flow in volatile oil reservoir using two-phase pseudo-pressure well test method

Energy Technology Data Exchange (ETDEWEB)

Sharifi, M.; Ahmadi, M. [Calgary Univ., AB (Canada)

2009-09-15

A study was conducted to better understand the behaviour of volatile oil reservoirs. Retrograde condensation occurs in gas-condensate reservoirs when the flowing bottomhole pressure (BHP) lowers below the dewpoint pressure, thus creating 4 regions in the reservoir with different liquid saturations. Similarly, when the BHP of volatile oil reservoirs falls below the bubblepoint pressure, two phases are created in the region around the wellbore, and a single phase (oil) appears in regions away from the well. In turn, higher gas saturation causes the oil relative permeability to decrease towards the near-wellbore region. Reservoir compositional simulations were used in this study to predict the fluid behaviour below the bubblepoint. The flowing bottomhole pressure was then exported to a well test package to diagnose the occurrence of different mobility regions. The study also investigated the use of a two-phase pseudo-pressure method on volatile and highly volatile oil reservoirs. It was concluded that this method can successfully predict the true permeability and mechanical skin. It can also distinguish between mechanical skin and condensate bank skin. As such, the two-phase pseudo-pressure method is particularly useful for developing after-drilling well treatment and enhanced oil recovery process designs. However, accurate relative permeability and PVT data must be available for reliable interpretation of the well test in volatile oil reservoirs. 18 refs., 3 tabs., 9 figs.

Polyalhpaolefins and VHVI base oils - base oils for high performance lubricants; Polyalfaolefine und VHVI-Grundoele - Grundoele fuer hochwertige Schmierstoffe

Energy Technology Data Exchange (ETDEWEB)

Lehmus, M.; Nissfolk, F.; Kulmala, K. [Fortum Oil and Gas Oyj / Base Oils, Fortum (Finland)

2002-01-01

Next to polyalphaolefines (PAOs base oils of the API/ATIEL Group IV), VHVI base oils (belonging to API/ATIEL Group III) are being increasingly used in high-performance automotive and industrial lubricants. A comparative study of the properties of VHVI base oils and polyalphaolefins shows that high-quality VHVI base oils have comparable volatility, oxidation stability and viscosity indices to polyalphaolefins, whereas the most pronounced differences are viscometric properties in the low-temperature range. However, there are noticeable differences between different market-typical VHVI base oils, depending primarily on the manufacturing process. The differences in the physicochemical properties of PAOs and various VHVI base oils are attributable to differences in the typical molecular composition. This is illustrated by a compositional analysis of several VHVI base oils, in which the (iso)paraffin content and the content of different naphthenic and aromatic compounds is analyzed. The base oil influence on specific properties of formulated lubricants is discussed on the basis of several examples, and studies conducted with passenger car engine oils (PCMOs), heavy-duty engine oils (HDEOs) and gear oils are described in detail. As a result of extremely low CCS viscosities, PAOs are optimally suited for use in 0W-X PCMOs whereas 5W-X PCMOs meeting highest performance requirements can also be formulated with high-quality VHVI base oils. Emission measurements with HDEOs formulated with either SN mineral base oil or VHVI base oil demonstrated that the base oil type affects tailpipe particle emissions in the particle size range <5 {mu}m as replacement of SN mineral base oil with VHVI base oil resulted in lower particle emissions. Test stand measurements with gear oils formulated with either VHVI base oils or PAOs yielded comparable results in terms of power transfer ratio and oil temperature increase. (orig.)

Determination of Minimum Miscibility Pressure in supercritical extractor using oil saturated sample

DEFF Research Database (Denmark)

Rudyk, Svetlana Nikolayevna; Søgaard, Erik Gydesen; Abbasi, Waqas A.

2009-01-01

with a given oil reservoir at the reservoir temperature. The oil formation to which the process is applied must be operated at or above the MMP. Before field trial this parameter is to be determined at the laboratory which traditionally is done by help of a slim tube or a raising bubble experiments. However...

Triacylglycerols profiling in plant oils important in food industry, dietetics and cosmetics using high-performance liquid chromatography-atmospheric pressure chemical ionization mass spectrometry.

Science.gov (United States)

Lísa, Miroslav; Holcapek, Michal

2008-07-11

Optimized non-aqueous reversed-phase high-performance liquid chromatography method using acetonitrile-2-propanol gradient elution and the column coupling in the total length of 45 cm has been applied for the high resolution separation of plant oils important in food industry, dietetics and cosmetics. Positive-ion atmospheric pressure chemical ionization mass spectrometry is used for the unambiguous identification and also the reliable quantitation with the response factors approach. Based on the precise determination of individual triacyglycerol concentrations, the calculation of average parameters important in the nutrition is performed, i.e. average carbon number, average double bond number, relative concentrations of essential, saturated, monounsaturated and polyunsaturated fatty acids. Results are reported in the form of both chromatographic fingerprints and tables containing relative concentrations for all triacylglycerols and fatty acids in individual samples. In total, 264 triacylglycerols consisting of 28 fatty acids with the alkyl chain length from 6 to 26 carbon atoms and 0 to 4 double bonds have been identified in 26 industrial important plant oils.

Value of NMR logging for heavy oil characterization

Energy Technology Data Exchange (ETDEWEB)

Chen, S.; Chen, J.; Georgi, D. [Baker Hughes, Calgary, AB (Canada); Sun, B. [Chevron Energy Technology Co., Calgary, AB (Canada)

2008-07-01

Non-conventional, heavy oil fields are becoming increasingly important to the security of energy supplies and are becoming economically profitable to produce. Heavy oil reservoirs are difficult to evaluate since they are typically shallow and the connate waters are very fresh. Other heavy oil reservoirs are oil-wet where the resistivities are not indicative of saturation. Nuclear magnetic resonance (NMR) detects molecular level interactions. As such, it responds distinctively to different hydrocarbon molecules, thereby opening a new avenue for constituent analysis. This feature makes NMR a more powerful technique than bulk oil density or viscosity measurements for characterizing oils, and is the basis for detecting gas in heavy oil fields. NMR logging, which measures fluid in pore space directly, is capable of separating oil from water. It is possible to discern movable from bound water by analyzing NMR logs. The oil viscosity can be also quantified from NMR logs, NMR relaxation time and diffusivity estimates. The unique challenges for heavy oil reservoir characterization for the NMR technique were discussed with reference to the extra-fast decay of the NMR signal in response to extra-heavy oil/tars, and the lack of sensitivity in measuring very slow diffusion of heavy oil molecules. This paper presented various methods for analyzing heavy oil reservoirs in different viscosity ranges. Heavy oil fields in Venezuela, Kazakhstan, Canada, Alaska and the Middle East were analyzed using different data interpretation approaches based on the reservoir formation characteristics and the heavy oil type. NMR direct fluid typing was adequate for clean sands and carbonate reservoirs while integrated approaches were used to interpret extra heavy oils and tars. It was concluded that NMR logs can provide quantitative measures for heavy oil saturation, identify sweet spots or tar streaks, and quantify heavy oil viscosity within reasonable accuracy. 14 refs., 16 figs.

τ-MnAl with high coercivity and saturation magnetization

Directory of Open Access Journals (Sweden)

J. Z. Wei

2014-12-01

Full Text Available In this paper, high purity τ-Mn54Al46 and Mn54−xAl46Cxalloys were successfully prepared using conventional arc-melting, melt-spinning, and heat treatment process. The magnetic and the structural properties were examined using x-ray diffraction (XRD, powder neutron diffraction and magnetic measurements. A room temperature saturation magnetization of 650.5 kAm-1, coercivity of 0.5 T, and a maximum energy product of (BHmax = 24.7 kJm-3 were achieved for the pure Mn54Al46 powders without carbon doping. The carbon substituted Mn54−xAl46Cx, however, reveals a lower Curie temperature but similar saturation magnetization as compared to the carbon-free sample. The electronic structure of MnAl shows that the Mn atom possesses a magnetic moment of 2.454 μB which results from strong hybridization between Mn-Al and Mn-Mn. We also investigated the volume and c/a ratio dependence of the magnetic moments of Mn and Al. The results indicate that an increase in the intra-atomic exchange splitting due to the cell volume expansion, leads to a large magnetic moment for the Mn atom. The Mn magnetic moment can reach a value of 2.9 μB at a volume expansion rate of ΔV/V ≈ 20%.

Semiconductor saturable absorbers for ultrafast terahertz signals

DEFF Research Database (Denmark)

Hoffmann, Matthias C.; Turchinovich, Dmitry

2010-01-01

states, due to conduction band onparabolicity and scattering into satellite valleys in strong THz fields. Saturable absorber parameters, such as linear and nonsaturable transmission, and saturation fluence, are extracted by fits to a classic saturable absorber model. Further, we observe THz pulse......We demonstrate saturable absorber behavior of n-type semiconductors GaAs, GaP, and Ge in the terahertz THz frequency range at room temperature using nonlinear THz spectroscopy. The saturation mechanism is based on a decrease in electron conductivity of semiconductors at high electron momentum...

Single corn kernel wide-line NMR oil analysis for breeding purpose

Energy Technology Data Exchange (ETDEWEB)

Wilmers, M C.C.; Rettori, C; Vargas, H; Barberis, G E [Universidade Estadual de Campinas (Brazil). Inst. de Fisica; da Silva, W J [Universidade Estadual de Campinas (Brazil). Inst. de Biologia

1978-12-01

The Wide-Line NMR technique was used to determine the oil content in single corn seeds. Using distinct radio frequency (RF) power, a systematic work was done in kernels with about 10% of moisture, and also in artificially dried seeds with approximated 5% of moisture. For nondried seeds NMR spectra showed clearly the presence of three resonances with different RF saturation factor. For dried seeds, the oil concentration determined by NMR was highly correlated (r = 0,997) with that determined by a gravimetric method. The highest discrepancy between the two methods was found to be about 1,3%. When relative measurements are required as in the case of single kernel for recurrent selection program, precision in the individual selected kernel will be about 2,5%. Applying this technique, a first cycle of recurrent selection using S/sub 1/ lines for low and high oil content was performed in an open pollinated variety. Gain from selection was 12.0 and 14.1% in the populations for high and low oil contents, respectively.

CG/MS quantitation of diamondoid compounds in crude oils and petroleum products

International Nuclear Information System (INIS)

Yang, C.; Wang, Z.D.; Hollebone, B.P.; Fingas, M.; Peng, X.; Landriault, M.

2006-01-01

Diamondoids are a class of saturated hydrocarbons that consist of 3-dimensionally fused cyclohexane rings. Diamondoid compounds in petroleum are the result of carbonium ion rearrangements of cyclic precursors on clay superacids in the source rock during oil generation. They are considered to be a problem due to their deposition during production of reservoir fluids and transportation of natural gas, gas condensates and light crude oils. At high concentrations, and with changes in pressure and temperature, diamondoid compounds can segregate out of reservoir fluids during production. Environmental scientists have considered fingerprinting the diamondoid hydrocarbons as a forensic method for oil spill studies. Since diamondoid compounds are thermodynamically stable, they have potential applications in oil-source correlation and differentiation for cases where traditional biomarker terpanes and steranes are absent because of environmental weathering or refining of petroleum products. Although there is increased awareness of possible use of diamondoid compounds for source identification, there is no systematic approach for using these compounds. Quantitative surveys of the abundances of diamondoids are not available. Therefore, this study developed a reliable analytical method for quantitative diamondoid analysis. Gas chromatography/mass spectrometry (GC/MS) was used to quantitatively determine diamondoid compounds (adamantane, diamantane and their alkylated homologues) in 14 fresh crude oils and 23 refined petroleum products, including light and mid-range distillate fuels, residual fuels and lubricating oils collected from different sources. Results were compared with 2 types of biomarker compounds in oil saturated hydrocarbon fractions. Several diagnostic ratios of diamondoids were developed based on their concentrations. Their potential use for forensic oil spill source identification was evaluated. 24 refs., 8 tabs., 4 figs

Space Charge Saturated Sheath Regime and Electron Temperature Saturation in Hall Thrusters

International Nuclear Information System (INIS)

Raitses, Y.; Staack, D.; Smirnov, A.; Fisch, N.J.

2005-01-01

Secondary electron emission in Hall thrusters is predicted to lead to space charge saturated wall sheaths resulting in enhanced power losses in the thruster channel. Analysis of experimentally obtained electron-wall collision frequency suggests that the electron temperature saturation, which occurs at high discharge voltages, appears to be caused by a decrease of the Joule heating rather than by the enhancement of the electron energy loss at the walls due to a strong secondary electron emission

Synthesis of high saturation magnetic iron oxide nanomaterials via low temperature hydrothermal method

Energy Technology Data Exchange (ETDEWEB)

Bhavani, P.; Rajababu, C.H. [Department of Materials Science & Nanotechnology, Yogivemana University, Vemanapuram 516003, Kadapa (India); Arif, M.D. [Environmental Magnetism Laboratory, Indian Institute of Geomagnetism (IIG), Navi Mumbai 410218, Mumbai (India); Reddy, I. Venkata Subba [Department of Physics, Gitam University, Hyderabad Campus, Rudraram, Medak 502329 (India); Reddy, N. Ramamanohar, E-mail: manoharphd@gmail.com [Department of Materials Science & Nanotechnology, Yogivemana University, Vemanapuram 516003, Kadapa (India)

2017-03-15

Iron oxide nanoparticles (IONPs) were synthesized through a simple low temperature hydrothermal approach to obtain with high saturation magnetization properties. Two series of iron precursors (sulfates and chlorides) were used in synthesis process by varying the reaction temperature at a constant pH. The X-ray diffraction pattern indicates the inverse spinel structure of the synthesized IONPs. The Field emission scanning electron microscopy and high resolution transmission electron microscopy studies revealed that the particles prepared using iron sulfate were consisting a mixer of spherical (16–40 nm) and rod (diameter ~20–25 nm, length <100 nm) morphologies that synthesized at 130 °C, while the IONPs synthesized by iron chlorides are found to be well distributed spherical shapes with size range 5–20 nm. On other hand, the IONPs synthesized at reaction temperature of 190 °C has spherical (16–46 nm) morphology in both series. The band gap values of IONPs were calculated from the obtained optical absorption spectra of the samples. The IONPs synthesized using iron sulfate at temperature of 130 °C exhibited high saturation magnetization (M{sub S}) of 103.017 emu/g and low remanant magnetization (M{sub r}) of 0.22 emu/g with coercivity (H{sub c}) of 70.9 Oe{sub ,} which may be attributed to the smaller magnetic domains (d{sub m}) and dead magnetic layer thickness (t). - Highlights: • Comparison of iron oxide materials prepared with Fe{sup +2}/Fe{sup +3} sulfates and chlorides at different temperatures. • We prepared super-paramagnetic and soft ferromagnetic magnetite nanoparticles. • We report higher saturation magnetization with lower coercivity.

Estimation of Fatty Acids in Corn Oil by Gas Capillary Chromatography

International Nuclear Information System (INIS)

Kamal, Mohammad A; Klein Peter

2007-01-01

Fatty acids provide energy as well as play important role in some cellular structures like cell membrane and certain hormones. Saturated fatty acids are usually found in animal products and in some vegetable oils as well. These saturated fatty acids may be a factor in weight gain and obesity but eating them in moderate amounts may not be damaging to health of every person. Monounsaturated fatty acids can lower blood levels of low density lipoprotein cholesterol and have potential to increase blood levels of high density lipoprotein cholesterol and by this way plays protective role against heart disease. The omega 3 and 6 fatty acids have vital roles in many biological systems such as nervous, immune, cardiovascular, dermal and vision systems. Therefore, it is essential to optimize the instrumental conditions and column specification for the estimation of various fatty acids in the oil, which was considered in the current study using Gas Capillary Chromatography. (author)

Lamb dip CRDS of highly saturated transitions of water near 1.4 μm

Science.gov (United States)

Kassi, S.; Stoltmann, T.; Casado, M.; Daëron, M.; Campargue, A.

2018-02-01

Doppler-free saturated-absorption Lamb dips were measured at sub-Pa pressures on rovibrational lines of H216O near 7180 cm-1, using optical feedback frequency stabilized cavity ring-down spectroscopy. The saturation of the considered lines is so high that at the early stage of the ring down, the cavity loss rate remains unaffected by the absorption. By referencing the laser source to an optical frequency comb, transition frequencies are determined down to 100 Hz precision and kHz accuracy. The developed setup allows resolving highly K-type blended doublets separated by about 10 MHz (to be compared to a HWHM Doppler width on the order of 300 MHz). A comparison with the most recent spectroscopic databases is discussed. The determined K-type splittings are found to be very well predicted by the most recent variational calculations.

Pore-scale simulation of wettability and interfacial tension effects on flooding process for enhanced oil recovery.

Science.gov (United States)

Zhao, Jin; Wen, Dongsheng

2017-08-27

For enhanced oil recovery (EOR) applications, the oil/water flow characteristics during the flooding process was numerically investigated with the volume-of-fluid method at the pore scale. A two-dimensional pore throat-body connecting structure was established, and four scenarios were simulated in this paper. For oil-saturated pores, the wettability effect on the flooding process was studied; for oil-unsaturated pores, three effects were modelled to investigate the oil/water phase flow behaviors, namely the wettability effect, the interfacial tension (IFT) effect, and the combined wettability/IFT effect. The results show that oil saturated pores with the water-wet state can lead to 25-40% more oil recovery than with the oil-wet state, and the remaining oil mainly stays in the near wall region of the pore bodies for oil-wet saturated pores. For oil-unsaturated pores, the wettability effects on the flooding process can help oil to detach from the pore walls. By decreasing the oil/water interfacial tension and altering the wettability from oil-wet to water-wet state, the remaining oil recovery rate can be enhanced successfully. The wettability-IFT combined effect shows better EOR potential compared with decreasing the interfacial tension alone under the oil-wet condition. The simulation results in this work are consistent with previous experimental and molecular dynamics simulation conclusions. The combination effect of the IFT reducation and wettability alteration can become an important recovery mechanism in future studies for nanoparticles, surfactant, and nanoparticle-surfactant hybrid flooding process.

Formulation of Zero-Trans Crystalized Fats Produced from Palm Stearin and High Oleic Safflower Oil Blends

Directory of Open Access Journals (Sweden)

Nydia E. Buitimea-Cantúa

2017-01-01

Full Text Available High intake of trans fat is associated with several chronic diseases such as cardiovascular disease and cancer. Fat blends, produced by direct blending process of palm stearin (PS with high oleic safflower oil (HOSO in different concentrations, were investigated. The effects of the PS addition (50, 70, or 90% and the rate of agitation (RA (1000, 2000, or 3000 rpm on physical properties, fatty acid profile (FAP, trans fatty acids (TFA, crystal structure, and consistency were researched. The blend containing 50% of each sort of oil (50% PS/50% HOSO showed that melting point and features were similar to the control shortening. The saturated fatty acids (SFA were higher followed by monounsaturated (MUFA and polyunsaturated fatty acids (PUFA. Significant differences in the content of palmitic and oleic acids among blends were observed. The 50% PS/50% HOSO blend contained higher oleic acid (42.9% whereas the 90% PS/10% HOSO was higher in palmitic acid (56.9%. The blending of PS/HOSO promoted the β crystal polymorphic forms. The direct blending process of equal amounts of PS and HOSO was an adequate strategy to formulate a new zero-trans crystallized vegetable fats with characteristics similar to commercial counterparts with well-balanced fats rich in both omega 3 and omega 6 fatty acids.

High-Viscosity Oil Filtration in the Pool Under Thermal Action

Science.gov (United States)

Shagapov, V. Sh.; Yumagulova, Yu. A.; Gizzatullina, A. A.

2018-05-01

We have developed a mathematical model and constructed numerical solutions of the problem of heating a high-viscosity oil pool through one horizontal well or a system of wells and have shown the possibility of their further operation until the limiting profitable discharge of oil is attained. The expenditure of heat in heating the oil pool, the evolution of discharge of oil, and the mass of extracted oil over the considered period have been considered.

Numerical approach for enhanced oil recovery with surfactant flooding

Directory of Open Access Journals (Sweden)

Sadegh Keshtkar

2016-03-01

Full Text Available The remained oil in the reservoir after conventional water-flooding processes, forms a dispersed phase in the form of oil drops which is trapped by capillary forces and is almost about 70% of the original oil in the place (OOIP. To reduce oil residual saturation in laboratory experiments and field projects, surfactant flooding is effective via decreasing the interfacial tension mobility ratio between oil and water phases. Estimation of the role of design variables, like chemical concentrations, partition coefficient and injection rate in different performance quantities, considering a heterogeneous and multiphase oil reservoir is a critical stage for optimal design. Increasing demand for oil production from water-flooded reservoirs has caused an increasing interest in surfactant-polymer (SP and alkali-surfactant-polymer (ASP. Modeling minimizes the risk of high cost of chemicals by improving our insight of process. In the present paper, a surfactant compositional flood model for a three-component (water, petroleum and surfactant, two phase (aqueous and oleic system is studied. A homogeneous, two-dimensional, isothermal reservoir with no free gas or alkali is assumed. The governing equations are in three categories: the continuity equations for the transport of each component, Darcy's equation for the transport of each phase and other auxiliary equations. The equations are solved by finite-differences using a procedure implicit in pressure and explicit in saturation. The validation of the model is achieved through comparing the modeling results with CMG simulators and Buckley–Leverett theory. The results of modeling showed good agreement with CMG results, and the comparison with Buckley–Leverett theory is explained according to different assumptions. After validation of the model, in order to investigate sensitivity analysis, the effects of system variables (partition coefficient, surface tension, oil viscosity and surface injection

Integrated and comparative proteomics of high-oil and high-protein soybean seeds.

Science.gov (United States)

Xu, Xiu Ping; Liu, Hui; Tian, Lihong; Dong, Xiang Bai; Shen, Shi Hua; Qu, Le Qing

2015-04-01

We analysed the global protein expression in seeds of a high-oil soybean cultivar (Jiyu 73, JY73) by proteomics. More than 700 protein spots were detected and 363 protein spots were successfully identified. Comparison of the protein profile of JY73 with that of a high-protein cultivar (Zhonghuang 13, ZH13) revealed 40 differentially expressed proteins, including oil synthesis, redox/stress, hydrolysis and storage-related proteins. All redox/stress proteins were less or not expressed in JY73, whereas the expression of the major storage proteins, nitrogen and carbon metabolism-related proteins was higher in ZH13. Biochemical analysis of JY73 revealed that it was in a low oxidation state, with a high content of polyunsaturated fatty acids and vitamin E. Vitamin E was more active than antioxidant enzymes and protected the soybean seed in a lower oxidation state. The characteristics of high oil and high protein in soybean, we revealed, might provide a reference for soybean nutrition and soybean breeding. Copyright © 2014 Elsevier Ltd. All rights reserved.

Monte Carlo Simulations of Neutron Oil well Logging Tools

International Nuclear Information System (INIS)

Azcurra, Mario

2002-01-01

Monte Carlo simulations of simple neutron oil well logging tools into typical geological formations are presented.The simulated tools consist of both 14 MeV pulsed and continuous Am-Be neutron sources with time gated and continuous gamma ray detectors respectively.The geological formation consists of pure limestone with 15% absolute porosity in a wide range of oil saturation.The particle transport was performed with the Monte Carlo N-Particle Transport Code System, MCNP-4B.Several gamma ray spectra were obtained at the detector position that allow to perform composition analysis of the formation.In particular, the ratio C/O was analyzed as an indicator of oil saturation.Further calculations are proposed to simulate actual detector responses in order to contribute to understand the relation between the detector response with the formation composition

Monte Carlo simulations of neutron oil well logging tools

International Nuclear Information System (INIS)

Azcurra, Mario O.; Zamonsky, Oscar M.

2003-01-01

Monte Carlo simulations of simple neutron oil well logging tools into typical geological formations are presented. The simulated tools consist of both 14 MeV pulsed and continuous Am-Be neutron sources with time gated and continuous gamma ray detectors respectively. The geological formation consists of pure limestone with 15% absolute porosity in a wide range of oil saturation. The particle transport was performed with the Monte Carlo N-Particle Transport Code System, MCNP-4B. Several gamma ray spectra were obtained at the detector position that allow to perform composition analysis of the formation. In particular, the ratio C/O was analyzed as an indicator of oil saturation. Further calculations are proposed to simulate actual detector responses in order to contribute to understand the relation between the detector response with the formation composition. (author)

Breeding and application of high-oil soybean varieties through radiation

International Nuclear Information System (INIS)

Guo Tai; Liu Zhongtang; Hu Xiping; Wang Zhixin; Wu Xiuhong; Zheng Wei; Chen Dexiang

2005-01-01

This paper reported the results of breeding and utilizing of high-oil soybean varieties, and at the same time, discussed the key technique of selecting high-oil soybean variety. This research based on crossbreeding, through genetic improvement and radiation treatment, continuous directive selection, combined with quality analysis and disease-resistant identification, and we had created four high-oil soybean varieties (lines), they were Hefeng46 (Hefu93154-4), Hefeng47(Hefu 93154-2), Hefeng48 (Hefu 93155-6), Hefu 93148-4. Their oil content ranges from 21.28% to 23.18%, and the yield is 2208-2578.5 kg/hm 2 , compared with the check, the yield is 10.1%-13.1% higher. All those varieties resisted one or two main soybean diseases. (authors)

Saturation of SERCA's lipid annulus may protect against its thermal inactivation

International Nuclear Information System (INIS)

Fajardo, Val Andrew; Trojanowski, Natalie; Castelli, Laura M.; Miotto, Paula M.; Amoye, Foyinsola; Ward, Wendy E.; Tupling, A. Russell; LeBlanc, Paul J.

2017-01-01

The sarco(endo)plasmic reticulum Ca 2+ -ATPase (SERCA) pumps are integral membrane proteins that catalyze the active transport of Ca 2+ into the sarcoplasmic reticulum, thereby eliciting muscle relaxation. SERCA pumps are highly susceptible to oxidative damage, and cytoprotection of SERCA dampens thermal inactivation and is a viable therapeutic strategy in combating diseases where SERCA activity is impaired, such as muscular dystrophy. Here, we sought to determine whether increasing the percent of saturated fatty acids (SFA) within SERCA's lipid annulus through diet could protect SERCA pumps from thermal inactivation. Female Wistar rats were fed either a semi-purified control diet (AIN93G, 7% soybean oil by weight) or a modified AIN93G diet containing high SFA (20% lard by weight) for 17 weeks. Soleus muscles were extracted and SERCA lipid annulus and activity under thermal stress were analyzed. Our results show that SERCA's lipid annulus is abundant with short-chain (12–14 carbon) fatty acids, which corresponds well with SERCA's predicted bilayer thickness of 21 Å. Under control-fed conditions, SERCA's lipid annulus was already highly saturated (79%), and high-fat feeding did not increase this any further. High-fat feeding did not mitigate the reductions in SERCA activity seen with thermal stress; however, correlational analyses revealed significant and strong associations between % SFA and thermal stability of SERCA activity with greater %SFA being associated with lower thermal inactivation and greater % polyunsaturation and unsaturation index being associated with increased thermal inactivation. Altogether, these findings show that SERCA's lipid annulus may influence its susceptibility to oxidative damage, which could have implications in muscular dystrophy and age-related muscle wasting. - Highlights: • SERCA's lipid annulus in rat soleus was measured after immunoconcentration. • Short fatty acid chains surround SERCA and

Experimental Study on Hydrate Induction Time of Gas-Saturated Water-in-Oil Emulsion using a High-Pressure Flow Loop

Directory of Open Access Journals (Sweden)

Lv X.F.

2015-11-01

Full Text Available Hydrate is one of the critical precipitates which have to be controlled for subsea flow assurance. The induction time of hydrate is therefore a significant parameter. However, there have been few studies on the induction time of the natural gas hydrate formation in a flow loop system. Consequently, a series of experiments were firstly performed, including water, natural gas and Diesel oil, on the hydrate induction time under various conditions such as the supercooling and supersaturation degree, water cut, anti-agglomerant dosage, etc. The experiments were conducted in a high-pressure hydrate flow loop newly constructed in the China University of Petroleum (Beijing, and dedicated to flow assurance studies. Then, based on previous research, this study puts forward a method for induction time, which is characterized by clear definition, convenient measurement and good generality. Furthermore, we investigated the influences of the experimental parameters and analyzed the experimental phenomena for the hydrate induction time in a flowing system.

Market opportunities and challenges for oil sands

International Nuclear Information System (INIS)

Wise, T.H.

2004-01-01

The use of Alberta bitumen as a clean fuel depends on upgrading, transportation, and refining processes. Forecasts show that oil sands production, which includes synthetic crude oil (SCO), will surpass declining conventional production from the Western Canada Sedimentary Basin. The challenges facing the oils sands processing industry include: crude oil prices which affect the producer's market; market expansion options; diluent availability/cost; supply cost competitiveness; and, regional processing. The common market issues include light/heavy crude prices, oil sands crude qualities, prices of oil sands crudes, pipeline infrastructure, and competitive supplies. The issues facing the refiners are: refining margins, security of crude supply, refined product quality, and competitive product supply. It was noted that Alberta must retain or increase its share of the Midwest market. The market expansion options were reviewed for both downstream (refining) and upstream (upgrading) operations. New pipeline capacity is needed to reach more distant markets such as Southern Midwest, Washington, and California. The market is nearly saturated for Canada's heavy oil supply. More upgrading will be required as bitumen production increases. Market growth is still possible for Canada's SCO but according to forecasts, the market could also become saturated. To increase demand and allow supplies to grow, SCO prices may fall below light crude prices. It was noted that a balance must be achieved in order for producers to increase production and for refiner/upgraders to expand their conversion capacity. 13 figs

Soybean Oil Is More Obesogenic and Diabetogenic than Coconut Oil and Fructose in Mouse: Potential Role for the Liver.

Directory of Open Access Journals (Sweden)

Poonamjot Deol

Full Text Available The obesity epidemic in the U.S. has led to extensive research into potential contributing dietary factors, especially fat and fructose. Recently, increased consumption of soybean oil, which is rich in polyunsaturated fatty acids (PUFAs, has been proposed to play a causal role in the epidemic. Here, we designed a series of four isocaloric diets (HFD, SO-HFD, F-HFD, F-SO-HFD to investigate the effects of saturated versus unsaturated fat, as well as fructose, on obesity and diabetes. C57/BL6 male mice fed a diet moderately high in fat from coconut oil and soybean oil (SO-HFD, 40% kcal total fat showed statistically significant increases in weight gain, adiposity, diabetes, glucose intolerance and insulin resistance compared to mice on a diet consisting primarily of coconut oil (HFD. They also had fatty livers with hepatocyte ballooning and very large lipid droplets as well as shorter colonic crypt length. While the high fructose diet (F-HFD did not cause as much obesity or diabetes as SO-HFD, it did cause rectal prolapse and a very fatty liver, but no balloon injury. The coconut oil diet (with or without fructose increased spleen weight while fructose in the presence of soybean oil increased kidney weight. Metabolomics analysis of the liver showed an increased accumulation of PUFAs and their metabolites as well as γ-tocopherol, but a decrease in cholesterol in SO-HFD. Liver transcriptomics analysis revealed a global dysregulation of cytochrome P450 (Cyp genes in SO-HFD versus HFD livers, most notably in the Cyp3a and Cyp2c families. Other genes involved in obesity (e.g., Cidec, Cd36, diabetes (Igfbp1, inflammation (Cd63, mitochondrial function (Pdk4 and cancer (H19 were also upregulated by the soybean oil diet. Taken together, our results indicate that in mice a diet high in soybean oil is more detrimental to metabolic health than a diet high in fructose or coconut oil.

Soybean Oil Is More Obesogenic and Diabetogenic than Coconut Oil and Fructose in Mouse: Potential Role for the Liver.

Science.gov (United States)

Deol, Poonamjot; Evans, Jane R; Dhahbi, Joseph; Chellappa, Karthikeyani; Han, Diana S; Spindler, Stephen; Sladek, Frances M

2015-01-01

The obesity epidemic in the U.S. has led to extensive research into potential contributing dietary factors, especially fat and fructose. Recently, increased consumption of soybean oil, which is rich in polyunsaturated fatty acids (PUFAs), has been proposed to play a causal role in the epidemic. Here, we designed a series of four isocaloric diets (HFD, SO-HFD, F-HFD, F-SO-HFD) to investigate the effects of saturated versus unsaturated fat, as well as fructose, on obesity and diabetes. C57/BL6 male mice fed a diet moderately high in fat from coconut oil and soybean oil (SO-HFD, 40% kcal total fat) showed statistically significant increases in weight gain, adiposity, diabetes, glucose intolerance and insulin resistance compared to mice on a diet consisting primarily of coconut oil (HFD). They also had fatty livers with hepatocyte ballooning and very large lipid droplets as well as shorter colonic crypt length. While the high fructose diet (F-HFD) did not cause as much obesity or diabetes as SO-HFD, it did cause rectal prolapse and a very fatty liver, but no balloon injury. The coconut oil diet (with or without fructose) increased spleen weight while fructose in the presence of soybean oil increased kidney weight. Metabolomics analysis of the liver showed an increased accumulation of PUFAs and their metabolites as well as γ-tocopherol, but a decrease in cholesterol in SO-HFD. Liver transcriptomics analysis revealed a global dysregulation of cytochrome P450 (Cyp) genes in SO-HFD versus HFD livers, most notably in the Cyp3a and Cyp2c families. Other genes involved in obesity (e.g., Cidec, Cd36), diabetes (Igfbp1), inflammation (Cd63), mitochondrial function (Pdk4) and cancer (H19) were also upregulated by the soybean oil diet. Taken together, our results indicate that in mice a diet high in soybean oil is more detrimental to metabolic health than a diet high in fructose or coconut oil.

Olive oil increases the magnitude of postprandial chylomicron remnants compared to milk fat and safflower oil.

Science.gov (United States)

Higashi, K; Ishikawa, T; Shige, H; Tomiyasu, K; Yoshida, H; Ito, T; Nakajima, K; Yonemura, A; Sawada, S; Nakamura, H

1997-10-01

The acute effects of olive oil, milk fat and safflower oil on postprandial lipemia and remnant lipoprotein metabolism were investigated. Eight Healthy male volunteers randomly underwent three types of oral fat-vitamin A loading tests. The test drink was a mixture of retinyl palmitate (RP)(50,000 IU of aqueous vitamin A/m2 body surface area) and one of the three types of oils (40 g of fat/m2 body surface area): olive oil (70.7% oleic acid of total fatty acids); milk fat (69.3% saturated fatty acid); safflower oil (74.2% linoleic acid). Olive oil significantly increased plasma triacylglycerol and RP concentrations 4 hours after fat loading, as compared to other fats. Increases of remnant like particle concentrations were higher after olive oil than after the other two fats. These results show that olive oil increases the magnitude of postprandial chylomicrons and chylomicron remnants compared to milk fat and safflower oil.

A novel method for the synergistic remediation of oil-water mixtures using nanoparticles and oil-degrading bacteria.

Science.gov (United States)

Alabresm, Amjed; Chen, Yung Pin; Decho, Alan W; Lead, Jamie

2018-07-15

Releases of crude oil and other types of oil from numerous sources can impose catastrophic physical, chemical, and biological effects on aquatic ecosystems. While currently-used oil removal techniques possess many advantages, they have inherent limitations, including low removal efficiencies and waste disposal challenges. The present study quantified the synergistic interactions of polyvinylpyrrolidone (PVP) coated magnetite nanoparticles (NP) and oil-degrading bacteria for enhanced oil removal at the laboratory scale. The results showed that at relatively high oil concentrations (375 mg L -1 ), NP alone could remove approximately 70% of lower-chain alkanes (C9-C22) and 65% of higher-chain (C23-C26), after only 1 h, when magnetic separation of NP was used. Removal efficiency did not increase significantly after that, which was likely due to saturation of the NP with oil. Microbial bioremediation, using strains of oil-degrading bacteria, removed almost zero oil immediately but 80-90% removal after 24-48 h. The combination of NPs and oil-degrading bacterial strains worked effectively to remove essentially 100% of oil within 48 h or less. This was likely due to the sorption of oil components to NPs and their subsequent utilization by bacteria as a joint Fe and C source, although the mechanisms of removal require further testing. Furthermore, results showed that the emission of selected volatile organic compounds (VOCs) and semi volatile organic compounds (SVOCs) were reduced after addition of NPs and bacteria separately. When combined, VOC and SVOC emissions were reduced by up to 80%. Copyright © 2018 Elsevier B.V. All rights reserved.

Evaluation of mineral oil saturated hydrocarbons (MOSH and mineral oil aromatic hydrocarbons (MOAH in pure mineral hydrocarbon-based cosmetics and cosmetic raw materials using 1H NMR spectroscopy [version 2; referees: 3 approved

Directory of Open Access Journals (Sweden)

Dirk W. Lachenmeier

2017-08-01

Full Text Available Mineral hydrocarbons consist of two fractions, mineral oil saturated hydrocarbons (MOSH and mineral oil aromatic hydrocarbons (MOAH. MOAH is a potential public health hazard because it may include carcinogenic polycyclic compounds. In the present study, 400 MHz nuclear magnetic resonance (NMR spectroscopy was introduced, in the context of official controls, to measure MOSH and MOAH in raw materials or pure mineral hydrocarbon final products (cosmetics and medicinal products. Quantitative determination (qNMR has been established using the ERETIC methodology (electronic reference to access in vivo concentrations based on the PULCON principle (pulse length based concentration determination. Various mineral hydrocarbons (e.g., white oils, paraffins or petroleum jelly were dissolved in deuterated chloroform. The ERETIC factor was established using a quantification reference sample containing ethylbenzene and tetrachloronitrobenzene. The following spectral regions were integrated: MOSH δ 3.0 – 0.2 ppm and MOAH δ 9.2 - 6.5, excluding solvent signals. Validation showed a sufficient precision of the method with a coefficient of variation <6% and a limit of detection <0.1 g/100 g. The applicability of the method was proven by analysing 27 authentic samples with MOSH and MOAH contents in the range of 90-109 g/100 g and 0.02-1.10 g/100 g, respectively. It is important to distinguish this new NMR-approach from the hyphenated liquid chromatography-gas chromatography methodology previously used to characterize MOSH/MOAH amounts in cosmetic products. For mineral hydrocarbon raw materials or pure mineral hydrocarbon-based cosmetic products, NMR delivers higher specificity without any sample preparation besides dilution. Our sample survey shows that previous methods may have overestimated the MOAH amount in mineral oil products and opens new paths to characterize this fraction. Therefore, the developed method can be applied for routine monitoring of consumer

Effects of Shiitake Intake on Serum Lipids in Rats Fed Different High-Oil or High-Fat Diets.

Science.gov (United States)

Asada, Norihiko; Kairiku, Rumi; Tobo, Mika; Ono, Akifumi

2018-04-27

Shiitake (Lentinula edodes) extract, eritadenine, has been shown to reduce cholesterol levels, and its hypocholesterolemic actions are involved in the metabolism of methionine. However, the mechanisms by which eritadenine affects cholesterol metabolism in animals fed a high-fat diet containing different sources of lipids have not yet been elucidated in detail. This study was conducted to investigate the effects of shiitake supplementation on serum lipid concentrations in rats fed a diet including a high amount of a plant oil (HO [high oil] and HOS [high oil with shiitake] groups), animal fat (HF [high fat] and HFS [high fat with shiitake] groups), or MCT- (medium-chain triglyceride-) rich plant oil (HM [high MCT] and HMS [high MCT with shiitake] groups). Rats in the HOS, HFS, and HMS groups were fed shiitake. When rats were fed a diet containing shiitake, serum triglyceride, cholesterol levels, and LCAT (lecithin-cholesterol acyltransferase) activities were lower in rats given MCT-rich plant oil than in those that consumed lard. The lipid type in the diet with shiitake also affected serum cholesterol levels and LCAT activities. The diet containing MCT-rich plant oil showed the greatest rates of decrease in all serum lipid profiles and LCAT activities. These results suggest that shiitake and MCT-rich plant oil work together to reduce lipid profiles and LCAT activity in serum.

Microbial enhanced oil recovery and compositions therefor

Science.gov (United States)

Bryant, Rebecca S.

1990-01-01

A method is provided for microbial enhanced oil recovery, wherein a combination of microorganisms is empirically formulated based on survivability under reservoir conditions and oil recovery efficiency, such that injection of the microbial combination may be made, in the presence of essentially only nutrient solution, directly into an injection well of an oil bearing reservoir having oil present at waterflood residual oil saturation concentration. The microbial combination is capable of displacing residual oil from reservoir rock, which oil may be recovered by waterflooding without causing plugging of the reservoir rock. Further, the microorganisms are capable of being transported through the pores of the reservoir rock between said injection well and associated production wells, during waterflooding, which results in a larger area of the reservoir being covered by the oil-mobilizing microorganisms.

In vivo determination of triglyceride (TG) secretion in rats fed different dietary saturated fats using [2-3H]-glycerol

International Nuclear Information System (INIS)

Lai, H.C.; Yang, H.; Lasekan, J.; Clayton, M.; Ney, D.M.

1990-01-01

Male, Sprague-Dawley rats (154±1 g) were fed diets containing 2% corn oil (CO) + 14% butterfat (BF), beef tallow (BT), olive oil (OO) or coconut oil (CN) vs a 16% CO control diet for 5 weeks. Changes in plasma TG specific activity (dpm/mg TG) were determined in individual unanesthetized rats after injection of 100 μCi [2- 3 H]-glycerol via a carotid cannula. Fractional rate constants were obtained using a 2-compartment model and nonlinear regression analysis. Results demonstrated no difference in the fractional rate constants among dietary groups; but, differences in the rates of hepatic TG secretion were noted. Rats fed BT showed a higher rate of hepatic TG secretion than rats fed CO. Rats fed BF, OO or CN showed somewhat higher rates of hepatic TG secretion than CO. VLDL TG, phospholipid, and apolipoprotein B and E levels were higher with saturated fats vs CO. The data suggest that the higher plasma TG levels noted in response to feeding saturated fats vs corn oil can be explained, in part, by an increased flux of hepatic TG secretion

Growing markets to sustain oil sands development

International Nuclear Information System (INIS)

Wise, T.H.

2003-01-01

The utilization of Alberta bitumen for the clean fuels market depends on upgrading, transportation, and refining processes. Forecasts show that oil sands production, which includes synthetic crude oil (SCO), will surpass declining conventional production in Western Canada. Several issues pose a challenge to the oil sands processing industry. The producers' market is affected by crude oil prices, market expansion options, diluent availability/cost, supply cost competitiveness, and regional processing. The common market issues include light/heavy crude prices, oil sands crude qualities, prices of oil sands crudes, pipeline infrastructure, and competitive supplies. The issues facing the refiners are: refining margins, security of crude supply, refined product quality, and competitive product supply. A brief review of markets for Canadian crude oil, including synthetic crude, was provided. The share of the Midwest market by Alberta must be retained and increased. The market expansion options were reviewed for both downstream (refining) and upstream (upgrading) operations. To reach more distant markets such as Southern Midwest, Washington, and California, new pipeline capacity would be required. The market is nearly saturated for Canada's heavy oil supply. More upgrading will be required as bitumen production increases. Market growth is still possible for Canada's SCO but according to forecasts, the market could also become saturated. To increase demand and allow supplies to grow, SCO prices may fall below light crude prices. It was noted that a balance must be achieved in order for producers to increase production and for refiner/upgraders to expand their conversion capacity. tabs., figs

Natural (Mineral, Vegetable, Coconut, Essential) Oils and Contact Dermatitis.

Science.gov (United States)

Verallo-Rowell, Vermén M; Katalbas, Stephanie S; Pangasinan, Julia P

2016-07-01

Natural oils include mineral oil with emollient, occlusive, and humectant properties and the plant-derived essential, coconut, and other vegetable oils, composed of triglycerides that microbiota lipases hydrolyze into glycerin, a potent humectant, and fatty acids (FAs) with varying physico-chemical properties. Unsaturated FAs have high linoleic acid used for synthesis of ceramide-I linoleate, a barrier lipid, but more pro-inflammatory omega-6:-3 ratios above 10:1, and their double bonds form less occlusive palisades. VCO FAs have a low linoleic acid content but shorter and saturated FAs that form a more compact palisade, more anti-inflammatory omega-6:-3 ratio of 2:1, close to 7:1 of olive oil, which disrupts the skin barrier, otherwise useful as a penetration enhancer. Updates on the stratum corneum illustrate how this review on the contrasting actions of NOs provide information on which to avoid and which to select for barrier repair and to lower inflammation in contact dermatitis genesis.

Experiment on the Influence Factors of Steam Distillation Rate of Crude Oil in Porous Media

Directory of Open Access Journals (Sweden)

Tian Guoqing

2017-01-01

Full Text Available To explore the influence of complexity of reservoir properties in porous media and the diversity of operating conditions on the steam distillation rate of crude oil in the process of heavy oil exploitation with steam injection, steam distillation simulation devices are used to study steam distillation rate of crude oil in porous media. Then steam distillation ratio is obtained under the condition of different core permeability, oil saturation, steam temperatures, system pressure, steam injection rates and steam distillation rates with different viscosities of crude oil. The results show that the steam distillation rate of crude oil in porous media depends mainly on the nature of the crude oil itself, for temperature and pressure are the key factors compared with the pore structure, the initial oil saturation and steam injection rate. The experimental results help estimate the amount of crude oil and the required steam in the reservoir in the steam drive process, aiming to facilitate the optimization design and operation of steam drive.

Multiphase flow modeling of a crude-oil spill site with a bimodal permeability distribution

Science.gov (United States)

Dillard, Leslie A.; Essaid, Hedeff I.; Herkelrath, William N.

1997-01-01

Fluid saturation, particle-size distribution, and porosity measurements were obtained from 269 core samples collected from six boreholes along a 90-m transect at a subregion of a crude-oil spill site, the north pool, near Bemidji, Minnesota. The oil saturation data, collected 11 years after the spill, showed an irregularly shaped oil body that appeared to be affected by sediment spatial variability. The particle-size distribution data were used to estimate the permeability (k) and retention curves for each sample. An additional 344 k estimates were obtained from samples previously collected at the north pool. The 613 k estimates were distributed bimodal lognormally with the two population distributions corresponding to the two predominant lithologies: a coarse glacial outwash deposit and fine-grained interbedded lenses. A two-step geostatistical approach was used to generate a conditioned realization of k representing the bimodal heterogeneity. A cross-sectional multiphase flow model was used to simulate the flow of oil and water in the presence of air along the north pool transect for an 11-year period. The inclusion of a representation of the bimodal aquifer heterogeneity was crucial for reproduction of general features of the observed oil body. If the bimodal heterogeneity was characterized, hysteresis did not have to be incorporated into the model because a hysteretic effect was produced by the sediment spatial variability. By revising the relative permeability functional relation, an improved reproduction of the observed oil saturation distribution was achieved. The inclusion of water table fluctuations in the model did not significantly affect the simulated oil saturation distribution.

Seed oil content and selected qualitative parameters of oils from grape seeds

Directory of Open Access Journals (Sweden)

Vladimír Mašán

2017-01-01

Full Text Available Grape seed oil (Oleum vitis viniferae represents promising plant oil, which is used mainly in gastronomy and for pharmaceutical purposes as well as for various technical applications. In this paper, there were examined oil contents and oil quality properties of seeds taken from 8 grape cultivars. Oil contents were found to be different for each cultivar, which ranged from 11.5% (Dornfelder to 17.5% (Riesling. The results showed a dependence between the length of the growing season for individual varie-ties and the total content of oil in seeds. Fatty acid concentrations in the evaluated oil samples were in various ranges, while the highest values were determined in linoleic acid 70.10 to 71.55%, oleic acid 15.61 to 17.14%, palmitic acid 6.87 to 8.18% and stearic acid 3.16 to 3.90%. Saturated fatty acid values were lower than the values of monounsaturated fatty acids and polyunsaturated fatty acids in all oil samples. The degree of unsaturation in the grape seed oil ranged between 88.6 - 89.21%. Thanks to its content, grape seed oil can be considered as a food supplement improving the nutri-tional value of the human diet.

Properties of organogels of high stearic soybean oil

Science.gov (United States)

Recently, the U.S. Food and Drug Administration (FDA) announced that food companies have to phase out the use of partially hydrogenated oils containing trans-fats by 2018. The use of high-stearic oils has been recognized as one of the ways to replace trans fats in food. Organogels also have drawn a ...

Production of synthetic hydrocarbon lube oil from highly waxy feedstocks

Energy Technology Data Exchange (ETDEWEB)

Xue, Q; Ding, Z; Zheng, Sh; Wu, W

1980-01-01

A feasible way to utilize the low value soft wax is to convert it into synthetic hydrocarbon lube oil by thermal cracking/polymerization route. The first commercial plant for this purpose has been in normal operation since 1970. It has been proved to be economically sound. The antioxidant response of the product polymer oil can be distinctly improved by hydro-refining. It has been found that the vacuum gas oil from highly waxy crude with or without furfural refining can be used as cracking stock. If high viscosity index polymer oil is desired, it is better to use slack wax as the cracking stock.

CO2 Enhanced Oil Recovery from the Residual Zone - A Sustainable Vision for North Sea Oil Production

Science.gov (United States)

Stewart, Jamie; Haszeldine, Stuart; Wilkinson, Mark; Johnson, Gareth

2014-05-01

This paper presents a 'new vision for North Sea oil production' where previously unattainable residual oil can be produced with the injection of CO2 that has been captured at power stations or other large industrial emitters. Not only could this process produce incremental oil from a maturing basin, reducing imports, it also has the capability to store large volumes of CO2 which can offset the emissions of additional carbon produced. Around the world oil production from mature basins is in decline and production from UK oil fields peaked in 1998. Other basins around the world have a similar story. Although in the UK a number of tax regimes, such as 'brown field allowances' and 'new field allowances' have been put in place to re-encourage investment, it is recognised that the majority of large discoveries have already been made. However, as a nation our demand for oil remains high and in the last decade imports of crude oil have been steadily increasing. The UK is dependent on crude oil for transport and feedstock for chemical and plastics production. Combined with the necessity to provide energy security, there is a demand to re-assess the potential for CO2 Enhanced Oil Recovery (CO2-EOR) in the UK offshore. Residual oil zones (ROZ) exist where one of a number of natural conditions beyond normal capillary forces have caused the geometry of a field's oil column to be altered after filling [1]. When this re-structuring happens the primary interest to the hydrocarbon industry has in the past been in where the mobile oil has migrated to. However it is now considered that significant oil resource may exist in the residual zone play where the main oil column has been displaced. Saturations within this play are predominantly close to residual saturation (Sr) and would be similar to that of a water-flooded field [2]. Evidence from a number of hydrocarbon fairways shows that, under certain circumstances, these residual zones in US fields are comparable in thickness to the

A combined high-sugar and high-saturated-fat dietary pattern is associated with more depressive symptoms in a multi-ethnic population: The HELIUS (Healthy Life in an Urban Setting) study

NARCIS (Netherlands)

Vermeulen, E.; Stronks, K.; Snijder, M.B.; Schene, A.H.; Lok, A.; Vries, J.H. de; Visser, M.; Brouwer, I.A.; Nicolaou, M.

2017-01-01

OBJECTIVE: To identify a high-sugar (HS) dietary pattern, a high-saturated-fat (HF) dietary pattern and a combined high-sugar and high-saturated-fat (HSHF) dietary pattern and to explore if these dietary patterns are associated with depressive symptoms. DESIGN: We used data from the HELIUS (Healthy

A combined high-sugar and high-saturated-fat dietary pattern is associated with more depressive symptoms in a multi-ethnic population: the HELIUS (Healthy Life in an Urban Setting) study

NARCIS (Netherlands)

Vermeulen, Esther; Stronks, Karien; Snijder, Marieke B.; Schene, Aart H.; Lok, Anja; De Vries, Jeanne H.; Visser, Marjolein; Brouwer, Ingeborg A.; Nicolaou, Mary

OBJECTIVE: To identify a high-sugar (HS) dietary pattern, a high-saturated-fat (HF) dietary pattern and a combined high-sugar and high-saturated-fat (HSHF) dietary pattern and to explore if these dietary patterns are associated with depressive symptoms. DESIGN: We used data from the HELIUS (Healthy

Serum albumin--a non-saturable carrier

DEFF Research Database (Denmark)

Brodersen, R; Honoré, B; Larsen, F G

1984-01-01

The shape of binding isotherms for sixteen ligands to human serum albumin showed no signs of approaching saturation at high ligand concentrations. It is suggested that ligand binding to serum albumin is essentially different from saturable binding of substrates to enzymes, of oxygen to haemoglobi...

Test methods for determining asphaltene stability in crude oils

Energy Technology Data Exchange (ETDEWEB)

Asomaning, S. [Baker Petrolite, Sugar Land, TX (United States)

2001-07-01

The development of test methods for the determination of the stability of asphaltenes in crude oils was rendered necessary, due to the high cost of remediating asphaltene deposition in harsh production environments, namely the underwater systems in offshore deepwater. The Oliensis Spot Test, two saturates, aromatics, resins and asphaltenes (SARA)-based screens (the Colloidal Instability Index and Asphaltene-Resin ratio), a solvent titration method with near infrared radiation (NIR) solids detection, and live oil depressurization were used for the purposes of this study, to predict the stability of asphaltenes in crude oils with different API gravity. A complete description of the test methods was provided, and the experimental data obtained as a result was presented. Correlation with data on the deposition histories of the oils was used to validate the experimental stability data. The author discussed the effectiveness of the different tests for the prediction of the stability of asphaltenes in crude oils. The prediction of a crude oil's propensity towards asphaltene precipitation was more accurate with the Colloidal Instability Index and the solvent titration method. Live oil depressurization proved to be very effective for the prediction of the stability of asphaltenes for light oils, where most stability tests fail. tabs., 31 figs.

Visualization of viscous coupling effects in heavy oil reservoirs

Energy Technology Data Exchange (ETDEWEB)

Ortiz-Arango, J.D. [Calgary Univ., AB (Canada). Tomographic Imaging and Porous Media Laboratory; Kantzas, A. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Calgary Univ., AB (Canada). Tomographic Imaging and Porous Media Laboratory

2008-10-15

Some heavy oil reservoirs in Venezuela and Canada have shown higher than expected production rates attributed to the effects of foamy oil or enhanced solution gas drive. However, foamy oil 2-phase flow does not fully explain oil rate enhancement in heavy oil reservoirs. In this study, flow visualization experiments were conducted in a 2-D etched network micromodel in order to determine the effect of the viscosity ratio on oil mobility at the pore scale. The micromodel's pattern was characterized by macroscopic heterogeneities with a random network of larger pore bodies interconnected with a random network of smaller pore throats. Displacement tests were conducted with green-dyed distilled water as a wetting phase. N-octane, bromododecane and mineral oil were used as non-wetting phases. An unsteady-state method was used to obtain displacement data, and the Alternate method was used to calculate relative permeabilities. Results of the study showed that relative permeabilities depended on the viscosity ratio of the fluids flowing through the porous medium. Channel and annular flows co-existed, and water lubrication was stronger at higher water saturations. The results of the study explained the abnormally high production rates in heavier oil fields. 19 refs., 3 tabs., 14 figs.

Palm oil and the heart:A review

Institute of Scientific and Technical Information of China (English)

Osaretin; J; Odia; Sandra; Ofori; Omosivie; Maduka

2015-01-01

Palm oil consumption and its effects on serum lipid levels and cardiovascular disease in humans is still a subject of debate. Advocacy groups with varying agenda fuel the controversy. This update intends to identify evidence-based evaluations of the influence of palm oil on serum lipid profile and cardiovascular disease. Furthermore, it suggests a direction for future research. The sources of information were based on a Pub Med, Google Scholar, African Journal online and Medline search using key words including: palm oil, palmitic acid, saturated fatty acids and heart disease. Published animal and human experiments on the association of palm oil and its constituents on the serum lipid profile and cardiovascular disease were also explored for relevant information. These papers are reviewed and the available evidence is discussed. Most of the information in mainstream literature is targeted at consumers and food companies with a view to discourage the consumption of palm oil. The main argument against the use of palm oil as an edible oil is the fact that it contains palmitic acid, which is a saturated fatty acid and by extrapolation should give rise to elevated total cholesterol and low-density lipoprotein cholesterol levels. However, there are many scientific studies, both in animals and humans that clearly show that palm oil consumption does not give rise to elevated serum cholesterol levels and that palm oil is not atherogenic. Apart from palmitic acid, palm oil consists of oleic and linoleic acids which are monounsaturated and polyunsaturated respectively. Palm oil also consists of vitamins A and E, which are powerful antioxidants. Palm oil has been scientifically shown to protect the heart and blood vessels from plaques and ischemic injuries. Palm oil consumed as a dietary fat as a part of a healthy balanced diet does not have incremental risk for cardiovascular disease. Little or no additional benefit will be obtained by replacing it with other oils rich in

Palm oil and the heart: A review.

Science.gov (United States)

Odia, Osaretin J; Ofori, Sandra; Maduka, Omosivie

2015-03-26

Palm oil consumption and its effects on serum lipid levels and cardiovascular disease in humans is still a subject of debate. Advocacy groups with varying agenda fuel the controversy. This update intends to identify evidence-based evaluations of the influence of palm oil on serum lipid profile and cardiovascular disease. Furthermore, it suggests a direction for future research. The sources of information were based on a PubMed, Google Scholar, African Journal online and Medline search using key words including: palm oil, palmitic acid, saturated fatty acids and heart disease. Published animal and human experiments on the association of palm oil and its constituents on the serum lipid profile and cardiovascular disease were also explored for relevant information. These papers are reviewed and the available evidence is discussed. Most of the information in mainstream literature is targeted at consumers and food companies with a view to discourage the consumption of palm oil. The main argument against the use of palm oil as an edible oil is the fact that it contains palmitic acid, which is a saturated fatty acid and by extrapolation should give rise to elevated total cholesterol and low-density lipoprotein cholesterol levels. However, there are many scientific studies, both in animals and humans that clearly show that palm oil consumption does not give rise to elevated serum cholesterol levels and that palm oil is not atherogenic. Apart from palmitic acid, palm oil consists of oleic and linoleic acids which are monounsaturated and polyunsaturated respectively. Palm oil also consists of vitamins A and E, which are powerful antioxidants. Palm oil has been scientifically shown to protect the heart and blood vessels from plaques and ischemic injuries. Palm oil consumed as a dietary fat as a part of a healthy balanced diet does not have incremental risk for cardiovascular disease. Little or no additional benefit will be obtained by replacing it with other oils rich in mono

Production and characterization of a functional Iranian white brined cheese by replacement of dairy fat with vegetable oils.

Science.gov (United States)

Achachlouei, B Fathi; Hesari, J; Damirchi, S Azadmard; Peighambardoust, Sh; Esmaiili, M; Alijani, S

2013-10-01

Full-fat cheese usually contains high amounts of saturated fatty acids and cholesterol, which may have negative health effects. In this study, full-fat white brined cheese, as a control sample, and experimental cheeses with olive and canola oils (T1, white brined cheese containing 50% canola oil, T2, white brined cheese containing 50% olive oil, T3, white brined cheese containing 100% canola oil and T4, white brined cheese containing 100% olive oil) were prepared from bovine milk. Physicochemical properties, lipolysis, proteolysis patterns and sensorial properties in the prepared samples were determined during 80 days of storage at 20-day intervals. Cheese incorporating vegetable oils showed lower amounts of saturated fatty acids and higher amounts of unsaturated fatty acids compared with the full-fat cheese (control) samples. Moisture, pH, lipolysis value, as assessed by the acid-degree value, and proteolysis values (pH 4.6 SN/TN% and NPN/TN%) significantly (p titrable acidity decreased during 40 days of ripening but then increased slightly. Sensory properties of white brined cheese incorporating with vegetable oils were different from those of full-fat cheese samples. White brined cheese containing olive and canola oils (100% fat substitution) received better sensory scores compared to other samples. The results showed that it is possible to replace dairy fat with olive and canola oils, which can lead to produce a new healthy and functional white brined cheese.

Viewpoint On the Climate Change Effects of High Oil Prices

International Nuclear Information System (INIS)

Vielle, M.; Viguier, L.

2005-11-01

Some commentators claim that the oil market has achieved within a few months what international bureaucrats have struggled to obtain in a decade of international climate negotiations. The fallacy of the oil price argument is that substitutions and income effects that would result from higher oil prices are not considered. Using a computable general equilibrium model, we show that high oil prices cannot serve as substitutes for effective climate policies.

A combined high-sugar and high-saturated-fat dietary pattern is associated with more depressive symptoms in a multi-ethnic population: the HELIUS (Healthy Life in an Urban Setting) study

NARCIS (Netherlands)

Vermeulen, Esther; Stronks, Karien; Snijder, Marieke B.; Schene, Aart H.; Lok, Anja; de Vries, Jeanne H.; Visser, Marjolein; Brouwer, Ingeborg A.; Nicolaou, Mary

2017-01-01

To identify a high-sugar (HS) dietary pattern, a high-saturated-fat (HF) dietary pattern and a combined high-sugar and high-saturated-fat (HSHF) dietary pattern and to explore if these dietary patterns are associated with depressive symptoms. We used data from the HELIUS (Healthy Life in an Urban

Biodegradation studies of oil sludge containing high hydrocarbons concentration

International Nuclear Information System (INIS)

Olguin-Lora, P.; Munoz-Colunga, A.; Castorena-Cortes, G.; Roldan-Carrillo, T.; Quej Ake, L.; Reyes-Avila, J.; Zapata-Penasco, I.; Marin-Cruz, J.

2009-01-01

Oil industry has a significant impact on environment due to the emission of, dust, gases, waste water and solids generated during oil production all the way to basic petrochemical product manufacturing stages. the aim of this work was to evaluate the biodegradation of sludge containing high hydrocarbon concentration originated by a petroleum facility. A sludge sampling was done at the oil residuals pool (ORP) on a gas processing center. (Author)

Microbial degradation of resins fractionated from Arabian light crude oil

International Nuclear Information System (INIS)

Venkateswaran, K.; Hoaki, T.; Kato, M.; Maruyama, T.

1995-01-01

Sediment samples from the Japanese coasts were screened for microorganisms able to degrade resin components of crude oil. A mixed population that could degrade 35% of 5000 ppm resin in 15 days was obtained. This population also metabolized 50% of saturates and aromatics present in crude oil (5000 ppm) in 7 days. A Pseudomonas sp., isolated from the mixed population, emulsified and degraded 30% of resins. It also degraded saturates and aromatics (30%) present in crude oil (5000 ppm). These results were obtained from Iatroscan analysis. Degradation of crude oil was also analyzed by gas chromatography (GC). The peaks corresponding to known aliphatic hydrocarbons in crude oil greatly decreased within the first two days of incubation in the cultures of the RY-mixed population and of Pseudomonas strain UN3. Aromatic compounds detected as a broad peak by GC were significantly degraded at day 7 by Pseudomonas strain UN3, and at day 15 by the RY-mixed population. Investigations are ongoing to determine the genetic basis for the ability of these organisms to grow on the resin fractions of crude oil as a sole source of carbon and energy. 28 refs., 4 figs., 1 tab

The North Cape oil spill assessment: PAHs in oil

International Nuclear Information System (INIS)

Brown, J.; Boehm, P. D.; Hardestine, J. H.; Douglas, G. S.

1997-01-01

The North Cape oil spill in January 1996 resulted in the release of an estimated 827,000 gallons of No. 2 home heating oil into the nearshore turbulent waters of coastal Rhode Island. The oil was mixed into the water column and was transported on the surface as well as below the surface. Some of the spilled oil entered the coastal ponds behind the beaches. Sampling and chemical analysis for detailed suites of petroleum saturated and polycyclic aromatic hydrocarbons (PAHs) was undertaken as part of the assessment of the fate of the oil spill and of the exposure to the marine environment. The ponds were found to contain significant quantities of background petroleum hydrocarbons, including petrogenic PAHs and combustion PAHs. Initial assessment pointed (incorrectly as it turned out) to widespread contamination due only to the North Cape spill. Application of advanced chemical fingerprinting approaches, and geochemical biomarker data illustrated that many of the PAHs consisted of combustion-related 4- and 5-ringed PAHs, attributable to diesel fuel used routinely by boats in the area. The analysis demonstrated that the use of non-specific total PAH data and insufficient fingerprinting and allocation of petrogenic residues has the potential to overestimate contamination and hence injury to the environment in similar oil spill situations

[Modern conceptions about the possible impact of palm oil on human health].

Science.gov (United States)

Medvedev, O S; Medvedeva, N A

2016-01-01

Review of the scientific literature on the evidence of the relationship between palm oil (PO) and its components and adverse effects on human health, on the mechanisms of cholesterol control and risks for development of cardiovascular diseases. PO is solid or semisolid at room temperature and often is used as a natural substitute for partially hydrogenated vegetable oils containing trans fatty acids which increase risks of hypercholesteremia. PO contains both saturated and unsaturated fats as well as substances with antioxidant activity. Taking into account the lipid theory of atherosclerosis pathogenesis, and sn-2 hypothesis, PO was compared with other vegetable oils, like olive, sunflower or soybean oils, and did not show great differences in changes of LDL, HDL or total cholesterol levels. Comparison of diets rich in PO with diets rich in trans fatty acids shows improvement of lipid profiles in groups with PO, and serves as a basis for replacement of trans fatty acids in food with PO and its fractions. In addition to fatty acids content, PO contains several phytonutrients including 4 forms of tocopherols and tocotrienols, carotenoids, sterols, and some others. Most of these compounds are considered beneficial for human health, mainly on account of their antioxidant activity. It is concluded that PO is safe component of food, when we pay attention to the rather high content of saturated fats in it.

Sensory properties during storage of crisps and French fries prepared with sunflower oil and high oleic sunflower oil

NARCIS (Netherlands)

Gemert, L.J. van

1996-01-01

A selected and trained descriptive sensory panel has assessed samples of crisps and French fries prepared on an industrial scale with either sunflower oil (SO) or high oleic sunflower oil (HOSO). Furthermore, crisps have been fried in these oils with or without dimethyl polysiloxane (DMPS).

CO{sub 2} flooding performance prediction for Alberta oil pools

Energy Technology Data Exchange (ETDEWEB)

Shaw, J.C. [Adams Pearson Associates Inc., Calgary, AB (Canada); Bachu, S. [Alberta Energy and Utilities Board, Calgary, AB (Canada)

2002-06-01

An advanced technical screening program was used to successfully screen and rank a very large number of Alberta oil pools for enhanced oil recovery using carbon dioxide (CO{sub 2}) flooding. This paper is a continuation paper describing the results of using the Microsoft Excel program with VBA to estimate production forecasts for several candidate pools in Alberta. A total of 6 ranking parameters were used, including API gravity of oil, residual oil saturation, ratio between reservoir pressure and minimum miscibility pressure, reservoir temperature, net pay thickness and porosity. The screening program provides a technical ranking of approximately 8,000 Alberta pools. After compilation of the Alberta oil pools, it was determined that most of the deep carbonate oil pools are excellent candidates for CO{sub 2} miscible flooding. Other Devonian carbonate pools are also ranked as having high potential for the process. An environmental benefit of CO{sub 2} miscible flooding process is that carbon sequestration has the potential to reduce anthropogenic carbon dioxide emissions from reaching the atmosphere. Ongoing studies are currently addressing CO{sub 2} capture and transportation, making EOR technology viable for maintaining light oil production in western Canada. 11 refs., 2 tabs., 2 figs.

The reduction of oil pollutants of petroleum products storage-tanks sludge using low-cost adsorbents

Directory of Open Access Journals (Sweden)

Mokhtari-Hosseini Zahra Beagom

2017-01-01

Full Text Available Disposal of storage tank sludge in oil depots is a major environmental concern due to the high concentration of hydrocarbons involved. This paper investigates the reduction of the sludge oil pollutants with initial oil and grease concentration of about 50 mass% using low cost adsorbents. Among the examined adsorbents, sawdust indicated the maximum removal of oil and grease. The screening and optimizing of process parameters were evaluated employing Plackett-Burman design and response surface method. For the optimized conditions, more than 60 mass% of oil and grease from the sludge was removed. Moreover, it was found that sawdust adsorption of the oil and grease approximately followed the Freundlich isotherm. The results indicated that oil pollutants of sludge could be reduced using sawdust as a low-cost, available and flammable adsorbent so that thus saturated adsorbents could be used as fuel in certain industries.

Multifactorial modelling of high-temperature treatment of timber in the saturated water steam medium

Science.gov (United States)

Prosvirnikov, D. B.; Safin, R. G.; Ziatdinova, D. F.; Timerbaev, N. F.; Lashkov, V. A.

2016-04-01

The paper analyses experimental data obtained in studies of high-temperature treatment of softwood and hardwood in an environment of saturated water steam. Data were processed in the Curve Expert software for the purpose of statistical modelling of processes and phenomena occurring during this process. The multifactorial modelling resulted in the empirical dependences, allowing determining the main parameters of this type of hydrothermal treatment with high accuracy.

Constructive Activation of Reservoir-Resident Microbes for Enhanced Oil Recovery

Science.gov (United States)

DeBruyn, R. P.

2017-12-01

Microbial communities living in subsurface oil reservoirs biodegrade oil, producing methane. If this process could create methane within the waterflooded pore spaces of an oilfield, the methane would be expected to remain and occupy pore space, decreasing water relative permeability, diverting water flow, and increasing oil recovery by expanding the swept zone of the waterflood. This approach was tested in an oilfield in northern Montana. Preliminary assessments were made of geochemical conditions and microbiological habitations. Then, a formulation of microbial activators, with composition tailored for the reservoir's conditions, was metered at low rates into the existing injection water system for one year. In the field, the responses observed included improved oil production performance; a slight increase in injection pressure; and increased time needed for tracers to move between injection and producing wells. We interpret these results to confirm that successful stimulation of the microbial community caused more methane to be created within the swept zone of the waterflooded reservoir. When the methane exsolved as water flowed between high-pressure injection and low-pressure production wells, the bubbles occupied pore space, reducing water saturation and relative permeability, and re-directing some water flow to "slower" unswept rock with lower permeability and higher oil saturation. In total, the waterflood's swept zone had been expanded to include previously-unflooded rock. This technology was applied in this field after screening based on careful anaerobic sampling, advanced microbiological analysis, and the ongoing success of its waterflood. No reservoir or geological or geophysical simulation models were employed, and physical modifications to field facilities were minor. This technology of utilizing existing microbial populations for enhanced oil recovery can therefore be considered for deployment into waterfloods where small scale, advanced maturity, or

Towards sustained high oil prices and increasingly volatile

International Nuclear Information System (INIS)

Auverlot, Dominique; Teillant, Aude; Rech, Olivier

2012-09-01

It is particularly difficult to predict the evolution of global oil production and its ability to meet the demand: the main uncertainties are related to the magnitude of the growth of emerging countries, more or less rapid decline in the production of major oil fields current events as well as natural or accidental, but especially geopolitics, which may affect, at any time, production. In a tight market today, the rapid growth of emerging economies, disruption of the oil supply chain world, even its mere mention, could cause short-term loss of excess production capacity - largely concentrated in Saudi Arabia - an increase substantial progress and, as contemplated by the International Atomic Energy imbalances between global oil supply and demand. If, after 2020, production of conventional oil begins to decline and the demand from emerging markets continues to grow, more massive imbalances may arise, leading to potential geopolitical tensions. Control would then demand the best answer. Otherwise, the resources of unconventional hydrocarbons, considerable expected to meet the demand, provided that their development is fast enough and their operating conditions are environmentally friendly. A consensus is emerging today on keeping oil prices high (above $ 100 / barrel) and volatile in the coming years, allowing some producing countries to pursue their development, but for France amplifying the negative effects on the economic growth oil bill (more than 49 billion euros in 2011) weighs more heavily in our trade deficit. In all cases, climate issues, the weight of the oil bill on our economy, securing our energy supply and technical uncertainties or geopolitical oil production call for reducing our oil consumption, accelerated motion the transition to a low carbon economy and development of our own energy resources. Contents: - Current analysis of oil reserves; - Uncertainties about the evolution of world oil production; - What is the potential long-term oil production

Mechanisms of radiation - chemical conversion of high-paraffinic crude oil

International Nuclear Information System (INIS)

Zaikin, Yu.A.; Zaikina, R.F.; Silverman, J.

2002-01-01

Complete text of publication follows. Regularities of radiation-thermal cracking (RTC) are studied in high-paraffinic oil. Irradiation of oil samples by 2 MeV electrons was performed using a special facility assembled at the electron accelerator ELU-4. The following characteristic RTC features were observed in oil with high contents of heavy paraffins: low level of isomerization in light RTC fractions; very high polymerization rate and low olefin contents in RTC products; relatively low yields of light fractions at low irradiation dose rates; increase in the molecular weight of the gasoline fraction as the irradiation dose rate grows. Similar intense polymerization of RTC products was observed in our experiments with such wastes of oil extraction as asphalt-pitch-paraffin sediments (APPS). Theoretically this feedstock contains great reserves of hydrogen, and, therefore, has high potential yields of light fractions. However, in this case RTC was accompanied by intense reactions of polymerization and chemical adsorption that limited the maximum yields of light RTC products to 40% in our experiments. A specific feature of APPS radiation-induced destruction is formation of the big amount of a reactive paraffinic residue. As a result of interaction with the polymerizing residue the light liquid fractions were completely absorbed and the heavy residue got denser and solidified after several days of exposure at room temperature. RTC regularities in heavy paraffinic oil differ from those observed both in highly viscous petroleum feedstock and light paraffin oils. We attribute these observations to the behavior of heavy alkyl radicals that initiate polymerization and isomerization in heavy paraffin fractions

Green coffee oil analysis by high-resolution nuclear magnetic resonance spectroscopy.

Science.gov (United States)

D'Amelio, Nicola; De Angelis, Elisabetta; Navarini, Luciano; Schievano, Elisabetta; Mammi, Stefano

2013-06-15

In this work, we show how an extensive and fast quantification of the main components in green coffee oil can be achieved by NMR, with minimal sample manipulation and use of organic solvents. The approach is based on the integration of characteristic NMR signals, selected because of their similar relaxation properties and because they fall in similar spectral regions, which minimizes offset effects. Quantification of glycerides, together with their fatty acid components (oleic, linoleic, linolenic and saturated) and minor species (caffeine, cafestol, kahweol and 16-O-methylcafestol), is achieved in less than 1h making use of (1)H and (13)C spectroscopy. The compositional data obtained are in reasonable agreement with classical chromatographic analyses. Copyright © 2013 Elsevier B.V. All rights reserved.

Lack of promotion of colon carcinogenesis by high-oleic safflower oil.

Science.gov (United States)

Takeshita, M; Ueda, H; Shirabe, K; Higuchi, Y; Yoshida, S

1997-04-15

The nonpromoting effect of olive oil on colon carcinogenesis has been attributed to its high oleic acid content, whereas a positive association of monounsaturated fat in beef tallow with colon tumors has been reported. The effect of constituents other than fatty acids could not be neglected in these experiments. In order to minimize the effects of minor constituents in the oils, the authors compared conventional safflower oil with oil from a mutant strain of safflower that is rich in oleic acid. ICR mice were treated with 1,2-dimethylhydrazine (DMH, 20 mg/kg body weight every week for 12 weeks) and then were fed either a high-fat diet (23.5% by weight), containing safflower oil (HF-LA) or high-oleic safflower oil (HF-OA), or a low-fat diet (5% by weight), containing safflower oil (LF-LA) or high-oleic safflower oil (LF-OA). The test diets were continued until termination of the experiment at 30 weeks after the first administration of DMH. Fatty acid composition of colon phospholipids was determined by gas-liquid chromatography-mass spectrometry. Tumor multiplicity in animals fed the HF-OA diet was indistinguishable from that in animals fed LF-LA or LF-OA. In contrast, animals fed the HF-LA diet had a significantly higher incidence of colon tumors (mostly adenocarcinomas) than the other groups. Fatty acid profiles of colon phospholipids reflected those of the diet. Animals fed a HF-LA diet showed a marked decrease of nervonic acid (C24:1, n-9) in the colon sphingomyelin. These data indicate that oleic acid does not enhance DMH-induced colon carcinogenesis in mice, even when they are fed a high-fat diet.

Gluon Saturation and EIC

Energy Technology Data Exchange (ETDEWEB)

Sichtermann, Ernst

2016-12-15

The fundamental structure of nucleons and nuclear matter is described by the properties and dynamics of quarks and gluons in quantum chromodynamics. Electron-nucleon collisions are a powerful method to study this structure. As one increases the energy of the collisions, the interaction process probes regions of progressively higher gluon density. This density must eventually saturate. An high-energy polarized Electron-Ion Collider (EIC) has been proposed to observe and study the saturated gluon density regime. Selected measurements will be discussed, following a brief introduction.

Performance of high-rate gravel-packed oil wells

Energy Technology Data Exchange (ETDEWEB)

Unneland, Trond

2001-05-01

Improved methods for the prediction, evaluation, and monitoring of performance in high-rate cased-hole gravel-packed oil wells are presented in this thesis. The ability to predict well performance prior to the gravel-pack operations, evaluate the results after the operation, and monitor well performance over time has been improved. This lifetime approach to performance analysis of gravel-packed oil wells contributes to increase oil production and field profitability. First, analytical models available for prediction of performance in gravel-packed oil wells are reviewed, with particular emphasis on high-velocity flow effects. From the analysis of field data from three North Sea oil fields, improved and calibrated cased-hole gravel-pack performance prediction models are presented. The recommended model is based on serial flow through formation sand and gravel in the perforation tunnels. In addition, new correlations for high-velocity flow in high-rate gravel-packed oil wells are introduced. Combined, this improves the performance prediction for gravel-packed oil wells, and specific areas can be targeted for optimized well design. Next, limitations in the current methods and alternative methods for evaluation and comparison of well performance are presented. The most widely used parameter, the skin factor, remains a convenient and important parameter. However, using the skin concept in direct comparisons between wells with different reservoir properties may result in misleading or even invalid conclusions. A discussion of the parameters affecting the skin value, with a clarification of limitations, is included. A methodology for evaluation and comparison of gravel-packed well performance is presented, and this includes the use of results from production logs and the use of effective perforation tunnel permeability as a parameter. This contributes to optimized operational procedures from well to well and from field to field. Finally, the data sources available for

EFFECT OF SILVER NANOPARTICLES ON THE PHYSICAL AND CHEMICAL PROPERTIES OF PLANT OILS AND THEIR ANTIMICROBIAL ACTIVITY

Directory of Open Access Journals (Sweden)

V. M. Minarchenko

2017-12-01

Full Text Available The aim of our research was to investigate the influence of silver nanoparticles on the physical and chemical features of plant oils of dogrose, flax, cedar, amaranth and watermelon and their antimicrobial activity. Plant oils were saturated with silver nanoparticles using electron-beam technology for depositing a molecular stream of metal in a vacuum. To characterize the rancidity of plant oils, the acid, iodine, peroxide, ester and saponification values were determined. A sharp drop in the iodine number and an increase in the peroxide number in oils saturated with silver nanoparticles were observed, as compared to pure oils, indicating a decrease in the number of unsaturated bonds in fatty acids and the formation of peroxides in oils. All pure plant oils and a separate sample of silver nanoparticles suppressed the growth of only E. faecalis colonies. Plant oils that were saturated with silver nanoparticles delayed the growth of S. aureus, S. epidermidis, E. faecalis, E. coli, P. aeruginosa, and C. albicans; the greatest delay in the growth of colonies was caused by flaxseed oil. Thus, the features of the plant oils under study essentially changed after they are aturated with silver nanoparticles. It can be assumed that the metal acted as a catalyst for peroxide oxidation of lipids in the investigated plant oil samples, the products of which caused toxic effects on cultures of bacteria and fungi in the experiment.

Highly efficient procedure for the transesterification of vegetable oil

Energy Technology Data Exchange (ETDEWEB)

Liang, Xuezheng; Gao, Shan; He, Mingyuan [Shanghai Key Laboratory of Green Chemistry and Chemical Process, Department of Chemistry, East China Normal University, Shanghai 200062 (China); Yang, Jianguo [Shanghai Key Laboratory of Green Chemistry and Chemical Process, Department of Chemistry, East China Normal University, Shanghai 200062 (China); Energy Institute, Department of Materials Science and Engineering, Pennsylvania State University, University Park, PA 16802 (United States)

2009-10-15

The highly efficient procedure has been developed for the synthesis of biodiesel from vegetable oil and methanol. The KF/MgO has been selected as the most efficient catalyst for the reactions with the yield of 99.3%. Operational simplicity, without need of the purification of raw vegetable oil, low cost of the catalyst used, high activities, no saponification and reusability are the key features of this methodology. (author)

Jussara berry (Euterpe edulis M.) oil-in-water emulsions are highly stable: the role of natural antioxidants in the fruit oil.

Science.gov (United States)

Carvalho, Aline G A; Silva, Kelly A; Silva, Laís O; Costa, André M M; Akil, Emília; Coelho, Maria A Z; Torres, Alexandre G

2018-05-23

Antioxidants help prevent lipid oxidation, and therefore are critical to maintain sensory quality and chemical characteristics of edible oils. Jussara berry (Euterpe edulis M.) oil is a source of minor compounds with potential antioxidant activity. The aim of this work was to investigate the role of such compounds on the effectiveness to prevent or delay oxidation of oil present in oil-in-water emulsions, and how the emulsions physical stability would be affected. Jussara berry oil extracted by ethanol extraction, its stripped variations (partially stripped, highly stripped and highly stripped with added BHT), and expeller pressed oil were used to prepare oil-in-water emulsions. Jussara berry oils were analyzed before emulsions preparation to ensure its initial quality and composition, and oil-in-water emulsions were analyzed regarding their oxidative and physical stability. Ethanol extracted oil emulsion presented higher oxidative stability when compared to highly stripped oil emulsion with added synthetic antioxidant BHT (oxidative stability index 45% lower, after 60 days, and reached undetectable levels after 90 days). All emulsions maintained physically stable for up to 120 days of storage. Our results indicate that natural antioxidants in jussara berry oil protect emulsions from oxidation while keeping physical stability unchanged. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Chemical characterization and oxidative stability of seeds and oil of sesame grown in Morocco

Directory of Open Access Journals (Sweden)

S. Gharby

2017-04-01

Full Text Available The objective of this research work was to determine the characteristic features of the oil content and composition of nutrients of sesame seeds grown in Morocco. Characteristic features of the seed oil revealed a high degree of unsaturation and as determined by gas chromatography reported herein, the major unsaturated fatty acids were linoleic acid (46.9% followed by oleic acid (37.4%, while the main saturated fatty acid was palmitic acid (9.1%. Sesame seed oil was also found to be rich in tocopherols with a predominance of γ-tocopherol (90.5%. The phytosterol marker β-sitosterol accounted for 59.9% of total sterols contained in sesame seed oil. This oil, therefore, has a potential for its use in human nutrition or industrial applications. Compositional analysis revealed that the sesame seeds contained considerable amounts of protein (22% and high amounts of lipids (52%. Nutrient information reported herein illustrates the benefits to public health for consumers of these plant seeds. In terms of oil, sesame seed oil may be considered as a valuable source for new multi-purpose products as industrial, cosmetic, and pharmaceutical uses.

Mineral oil barrier sequential polymer treatment for recycled paper products in food packaging

Science.gov (United States)

Paul, Uttam C.; Fragouli, Despina; Bayer, Ilker S.; Mele, Elisa; Conchione, Chiara; Cingolani, Roberto; Moret, Sabrina; Athanassiou, Athanassia

2017-01-01

Recycled cellulosic paperboards may include mineral oils after the recycle process, which together with their poor water resistance limit their use as food packaging materials. In this work, we demonstrate that a proper functionalization of the recycled paper with two successive polymer treatments, imposes a mineral oil migration barrier and simultaneously renders it waterproof and grease resistant, making it an ideal material for food contact. The first poly (methyl methacrylate) treatment penetrates the paper network and creates a protective layer around every fiber, permitting thus the transformation of the paperboard to a hydrophobic material throughout its thickness, reducing at the same time the mineral oil migration. Subsequently, the second layer with a cyclic olefin copolymer fills the open pores of the surface, and reduces the mineral oil hydrocarbons migration at levels below those proposed by the BMEL. Online liquid chromatography-gas chromatography coupled with flame ionization detection quantitatively demonstrate that this dual functional treatment prevents the migration of both saturated (mineral oil saturated hydrocarbons) and aromatic hydrocarbon (mineral oil aromatic hydrocarbons) mineral oils from the recycled paperboard to a dry food simulant.

Mitigation of Oil in Water Column: Mitigation Prototype Tests

Science.gov (United States)

2017-06-01

designed with an open end to allow aquatic animals to escape. After the treated foam becomes saturated with submerged oil, the net would be lifted...needed openings to allow the frame to pass through the water column without causing severe drag resistance . However, this also allows oil to flow...to the water and should only help the regions of hypoxia caused by microbial degradation of the oil. However, the proposed field set up with

Flashing of high-pressure saturated water into the pool water

International Nuclear Information System (INIS)

Takamasa, Tomoji; Kondo, Koichi; Aya, Izuo.

1997-01-01

This paper presents an experimental study on a saturated high-pressure water discharging into a water pool. The purpose of the experiment is to clarify the phenomena that occur by a blow-down of the water from the pressure vessel into the water-filled containment in the case of a wall-crack accident or a LOCA in a passive safety reactor. The results show that a flashing oscillation (FO) occurs when the water discharges into the pool, under specified experimental conditions. The range of the flashing location oscillates between a point very close to and some distance away from the vent hole. The pressures in the vent tube and water pool constantly fluctuate due to the flashing oscillation. The pressure oscillation and alternating flashing location might be caused by the balancing action between the supply of saturated water, flashing at the control volume and steam condensation on the steam-water interface. The frequencies of FO, or frequencies of pressure oscillation and alternating flashing location, increased as water subcooling increased, and as discharging pressure and vent hole diameter decreased. A linear analysis was conducted using a spherical flashing bubble model in which the motion of bubble is controlled by steam condensation. The effects of these parameters on the period of FO in the experiments can be predicted well by the analysis. (author)

Physico-chemical characteristics of Mesua ferrea seed oil and ...

African Journals Online (AJOL)

Saturated and unsaturated fatty acids present in the oils were separated and amounted to be (27.40-29.11 %) and (65.85- 68.31 %), respectively, depending upon the areas from where the seeds were collected. GLC analysis of the oil indicated the presence of palmitic acid (10.87%), linoleic acid (13.68%), oleic acid ...

Method for creating high carbon content products from biomass oil

Science.gov (United States)

Parker, Reginald; Seames, Wayne

2012-12-18

In a method for producing high carbon content products from biomass, a biomass oil is added to a cracking reactor vessel. The biomass oil is heated to a temperature ranging from about 100.degree. C. to about 800.degree. C. at a pressure ranging from about vacuum conditions to about 20,700 kPa for a time sufficient to crack the biomass oil. Tar is separated from the cracked biomass oil. The tar is heated to a temperature ranging from about 200.degree. C. to about 1500.degree. C. at a pressure ranging from about vacuum conditions to about 20,700 kPa for a time sufficient to reduce the tar to a high carbon content product containing at least about 50% carbon by weight.

Associating Polymer Networks Based on Cyclodextrin Inclusion Compounds for Heavy Oil Recovery

Directory of Open Access Journals (Sweden)

Xi Li

2018-01-01

Full Text Available This work evaluates an approach to improve the enhanced heavy oil recovery performance of hydrophobic associating polymer. A polymeric system based on water-soluble hydrophobic associating polymer (WSHAP and cyclodextrin (CD polymer was proposed in this work. Addition of CD polymer to WSHAP forms interpolymer bridges by inclusion of CD groups with hydrophobic tails, and thereby the network structure is strengthened. The proposed system offers good viscoelasticity, pronounced shear thinning, and interesting viscosity-temperature relations. Sand pack tests indicated that the proposed system can build high resistance factor during the propagation in porous media, and its moderate adsorption phenomenon was represented by the thickness of the adsorbed layer. The relationship between effective viscosity and oil recovery increment indicated that the proposed system can significantly reduce the residual oil saturation due to the “piston-like” propagation. The overall oil recovery was raised by 5.7 and 24.5% of the original oil in place compared with WSHAP and partially hydrolyzed polyacrylamide (HPAM, respectively.

Edible oil structuring: an overview and recent updates.

Science.gov (United States)

Patel, Ashok R; Dewettinck, Koen

2016-01-01

In recent years, research dealing with edible oil structuring has received considerable interest from scientific community working in the area of food formulation. Much of this interest is linked to the possibility of using structured oil in development of newer product formats with improved nutritional profile (trans fat-free, low in saturated fats and high in mono and/or poly unsaturated fatty acids). In addition to the obvious industrial need of finding the alternative formulation approach, the interesting properties of structured systems (particularly, oleogels) also makes them a fascinating subject for fundamental studies. In this paper, we attempt to give a comprehensive and concise overview of the field of oil structuring with special emphasis on the updates from recent years. Specifically, several categories of food-grade oleogelators and their potential food applications are summarized with typical examples along with a discussion on the general principles and unresolved challenges related to this emerging area.

High-glycemic index carbohydrates abrogate the antiobesity effect of fish oil in mice

DEFF Research Database (Denmark)

Hao, Qin; Lillefosse, Haldis Haukås; Fjære, Even

2012-01-01

Fish oil rich in n-3 polyunsaturated fatty acids is known to attenuate diet-induced obesity and adipose tissue inflammation in rodents. Here we aimed to investigate whether different carbohydrate sources modulated the antiobesity effects of fish oil. By feeding C57BL/6J mice isocaloric high-fat d...... metabolic effects of fish oil by demonstrating that high-GI carbohydrates attenuate the antiobesity effects of fish oil.......Fish oil rich in n-3 polyunsaturated fatty acids is known to attenuate diet-induced obesity and adipose tissue inflammation in rodents. Here we aimed to investigate whether different carbohydrate sources modulated the antiobesity effects of fish oil. By feeding C57BL/6J mice isocaloric high...

Dynamic characterization of oil fields, complex stratigraphically using genetic algorithms

International Nuclear Information System (INIS)

Gonzalez, Santiago; Hidrobo, Eduardo A

2004-01-01

A novel methodology is presented in this paper for the characterization of highly heterogeneous oil fields by integration of the oil fields dynamic information to the static updated model. The objective of the oil field's characterization process is to build an oil field model, as realistic as possible, through the incorporation of all the available information. The classical approach consists in producing a model based in the oil field's static information, having as the process final stage the validation model with the dynamic information available. It is important to clarify that the term validation implies a punctual process by nature, generally intended to secure the required coherence between productive zones and petrophysical properties. The objective of the proposed methodology is to enhance the prediction capacity of the oil field's model by previously integrating, parameters inherent to the oil field's fluid dynamics by a process of dynamic data inversion through an optimization procedure based on evolutionary computation. The proposed methodology relies on the construction of the oil field's high-resolution static model, escalated by means of hybrid techniques while aiming to preserve the oil field's heterogeneity. Afterwards, using an analytic simulator as reference, the scaled model is methodically modified by means of an optimization process that uses genetic algorithms and production data as conditional information. The process's final product is a model that observes the static and dynamic conditions of the oil field with the capacity to minimize the economic impact that generates production historical adjustments to the simulation tasks. This final model features some petrophysical properties (porosity, permeability and water saturation), as modified to achieve a better adjustment of the simulated production's history versus the real one history matching. Additionally, the process involves a slight modification of relative permeability, which has

Laboratory evaluation of biodegradation of crude oil contaminated tundra soil

International Nuclear Information System (INIS)

Schepart, B.S.; Hyzy, J.B.; Jorgenson, M.T.

1992-01-01

A laboratory experiment was designed to evaluate oil degradation rates in heavily contaminated soil samples from an oil spill site under various redox and nutrient conditions. Reduction of total petroleum hydrocarbons (TPH) in the experiment by indigenous bacteria was found to be negligible under aerobic conditions for all nutrient amendments over a 12-week period. The unexpectedly poor performance of the aerobic treatment may have been due to the high concentration of TPH (153,487 ppM) and the slow rate at which indigenous bacteria grew, or the preferential use of biogenic carbon over petroleum hydrocarbons. In contrast, under anaerobic conditions TPH was reduced by 47% in high nitrogen and phosphorous microcosms. The unexpectedly good performance of anaerobic bacteria indicates that promotion of oil degradation in saturated subsurface soils is feasible. The best degradation rates, however, were achieved by application of bacterial amendments, which reduced TPH up to 60% over 12 weeks. The higher degradation rates using bacterial amendments were attributed to the relatively rapid rate at which the bacteria colonized the substrates. This result suggests that bacterial additions in the field would be useful for promoting more rapid degradation of oil, while the slower growing indigenous oil-degrading bacteria population is allowed to increase. 19 refs., 9 figs., 3 tabs

Geotechnical properties of crude oil contaminated sand

International Nuclear Information System (INIS)

Puri, V.K.; Das, B.M.; Cook, E.E.; Shin, E.C.

1994-01-01

Contamination of soil due to an oil spill influences its subsequent engineering behavior. An investigation was conducted to study the effect of crude oil contamination on compaction characteristics, shear strength, one-dimensional compression, and coefficient of permeability. Water permeability was also determined by using commercial grade motor oils as contaminants. The test results indicate that the compaction characteristics are influenced by oil contamination. The angle of internal friction of sand (based on total stress condition) decreases due to presence of oil within the pore spaces in sand. One dimensional compression characteristics of sand are significantly influenced by oil contamination resulting in a decrease in the value of constrained modulus with increase in the degree of oil contamination compared to the case of dry sand. Water permeability was observed to be a function of the initial viscosity and the degree of saturation due to the contaminating oil

Homogeneous, heterogeneous and enzymatic catalysis for transesterification of high free fatty acid oil (waste cooking oil) to biodiesel: a review.

Science.gov (United States)

Lam, Man Kee; Lee, Keat Teong; Mohamed, Abdul Rahman

2010-01-01

In the last few years, biodiesel has emerged as one of the most potential renewable energy to replace current petrol-derived diesel. It is a renewable, biodegradable and non-toxic fuel which can be easily produced through transesterification reaction. However, current commercial usage of refined vegetable oils for biodiesel production is impractical and uneconomical due to high feedstock cost and priority as food resources. Low-grade oil, typically waste cooking oil can be a better alternative; however, the high free fatty acids (FFA) content in waste cooking oil has become the main drawback for this potential feedstock. Therefore, this review paper is aimed to give an overview on the current status of biodiesel production and the potential of waste cooking oil as an alternative feedstock. Advantages and limitations of using homogeneous, heterogeneous and enzymatic transesterification on oil with high FFA (mostly waste cooking oil) are discussed in detail. It was found that using heterogeneous acid catalyst and enzyme are the best option to produce biodiesel from oil with high FFA as compared to the current commercial homogeneous base-catalyzed process. However, these heterogeneous acid and enzyme catalyze system still suffers from serious mass transfer limitation problems and therefore are not favorable for industrial application. Nevertheless, towards the end of this review paper, a few latest technological developments that have the potential to overcome the mass transfer limitation problem such as oscillatory flow reactor (OFR), ultrasonication, microwave reactor and co-solvent are reviewed. With proper research focus and development, waste cooking oil can indeed become the next ideal feedstock for biodiesel.

Computer modeling of oil spill trajectories with a high accuracy method

International Nuclear Information System (INIS)

Garcia-Martinez, Reinaldo; Flores-Tovar, Henry

1999-01-01

This paper proposes a high accuracy numerical method to model oil spill trajectories using a particle-tracking algorithm. The Euler method, used to calculate oil trajectories, can give adequate solutions in most open ocean applications. However, this method may not predict accurate particle trajectories in certain highly non-uniform velocity fields near coastal zones or in river problems. Simple numerical experiments show that the Euler method may also introduce artificial numerical dispersion that could lead to overestimation of spill areas. This article proposes a fourth-order Runge-Kutta method with fourth-order velocity interpolation to calculate oil trajectories that minimise these problems. The algorithm is implemented in the OilTrack model to predict oil trajectories following the 'Nissos Amorgos' oil spill accident that occurred in the Gulf of Venezuela in 1997. Despite lack of adequate field information, model results compare well with observations in the impacted area. (Author)

Application of alkaline waterflooding to a high acidity crude oil

Energy Technology Data Exchange (ETDEWEB)

Sayyouh, M.H. (King Sand Univ., Riyadh (SA). Petroleum Engineering Dept.); Abdel-Waly, A.; Osman, A. (Cairo Univ. (EG). Petroleum Engineering Dept.); Awara, A.Z. (Geisum Oil Company, Cairo (EG))

The enhanced recovery of a high acidity crude oil (South Geisum crude) by alkaline solutions is studied. Acidity, interfacial tension, and contact angle, were investigated. Displacement tests were carried out to study the effect of alkaline slug concentration, slug size, oil alkali type, temperature and viscosity on recovery. The interfacial tension between crude oil and formation water decreases with increasing alkaline concentration until a minimum, after which it increases again. Contact angle measurements indicated oil-wetting conditions that increase by the addition of alkaline solutions. At the early stages of displacement, oil recovery increases with increasing alkaline concentration until a maximum at 4% by weight NaOH concentration. Also, at such early stages, an excessive increase in alkaline concentration results in lower oil recovery. On the other hand, after the injection of many pore volumes of water, oil recovery is almost the same regardless of the alkaline concentration. Oil recovery increases with increasing alkaline slug size until a maximum at 15% PV. Sodium hydroxide slugs produce more oil recovery than sodium carbonate slugs. Oil recovery increases with increasing temperature (from 25 to 55{sup 0}C) and decreasing oil viscosity.

Aspects of the use of saturated fluorocarbon fluids in high energy physics

Energy Technology Data Exchange (ETDEWEB)

Hallewell, G., E-mail: Gregory.Hallewell@cern.c [Centre de Physique des Particules de Marseille, 163 Avenue de Luminy, Case 907, 13288 Marseille Cedex 09 (France)

2011-05-21

The excellent dielectric properties of saturated fluorocarbons have allowed their use in direct immersion liquid cooling of electronics, including supercomputers and as heat transfer media in vapour phase soldering and burn-in testing of electronics. Their high density, UV transparency, non-flammability, non-toxicity and radiation tolerance have led to their use as liquid and gas radiator media for RICH detectors in numerous particle physics experiments. Systems to circulate and purify saturated fluorocarbon Cherenkov radiator vapours often rely on thermodynamic evaporation-condensation cycles similar to those used in refrigeration. Their use as evaporative refrigerants was pioneered for the ATLAS silicon tracker, and they are now also used as evaporative coolants in ALICE and TOTEM and as liquid coolants in ATLAS and CMS. Ultrasonic techniques for vapour phase analysis of fluorocarbon mixtures-developed for the SLAC SLD barrel CRID radiator during the 1980s as an alternative to UV refractometry are again under development for the ATLAS tracker evaporative cooling system. Examples of fluorocarbon circulation systems, together with purification and analysis techniques for these versatile fluids are mentioned.

Aspects of the use of saturated fluorocarbon fluids in high energy physics

International Nuclear Information System (INIS)

Hallewell, G.

2011-01-01

The excellent dielectric properties of saturated fluorocarbons have allowed their use in direct immersion liquid cooling of electronics, including supercomputers and as heat transfer media in vapour phase soldering and burn-in testing of electronics. Their high density, UV transparency, non-flammability, non-toxicity and radiation tolerance have led to their use as liquid and gas radiator media for RICH detectors in numerous particle physics experiments. Systems to circulate and purify saturated fluorocarbon Cherenkov radiator vapours often rely on thermodynamic evaporation-condensation cycles similar to those used in refrigeration. Their use as evaporative refrigerants was pioneered for the ATLAS silicon tracker, and they are now also used as evaporative coolants in ALICE and TOTEM and as liquid coolants in ATLAS and CMS. Ultrasonic techniques for vapour phase analysis of fluorocarbon mixtures-developed for the SLAC SLD barrel CRID radiator during the 1980s as an alternative to UV refractometry are again under development for the ATLAS tracker evaporative cooling system. Examples of fluorocarbon circulation systems, together with purification and analysis techniques for these versatile fluids are mentioned.

Sesame and flaxseed oil: nutritional quality and effects on serum lipids and glucose in rats

Directory of Open Access Journals (Sweden)

Rita de Cássia Avellaneda Guimarães

2013-03-01

Full Text Available This study evaluated the nutritional value of sesame and flaxseed oils and their effects on the lipid and glucose profile of rats fed diets containing different fat combinations. Fatty acid composition, refractive index, and iodine and saponification values were analyzed to characterize the oils. In the biological assay, Wistar rats were fed different diets, whose fat composition consisted of varying combinations of flaxseed oil, sesame oil, and animal fat. The primary constituents of the sesame oil were oleic (28.6%, linoleic (28.4%, and lauric acid (14.6%; for the flaxseed oil they were alpha-linolenic (39.90%, oleic (17.97% and linoleic acid (12.25%. The iodine and saponification values of the oils were within the reference range. Rats fed flaxseed oil-based diets had the lowest serum cholesterol values, whereas rats fed diets with flaxseed oil + sesame oil + animal fat had the highest glucose levels. HDL levels decreased significantly with flaxseed oil. Sesame and flaxseed oils are sources of polyunsaturated fatty acids (PUFA, and the flaxseed oil-based diet had a hypocholesterolemic effect, whereas sesame oil showed oxidative stability since it contains high levels of monounsaturated and saturated fatty acids.

Psyllium husk fiber supplementation to the diets rich in soybean or coconut oil: hypocholesterolemic effect in healthy humans.

Science.gov (United States)

Ganji, V; Kies, C V

1996-03-01

The objective of this study was to investigate the effect of psyllium husk fiber supplementation to the diets of soybean and coconut oil on serum lipids in normolipidemic humans. A 28-day study was divided into four 7-day experimental periods. Dietary periods were soybean oil (SO), soybean oil plus psyllium fiber (SO + PF), coconut oil (CO) and coconut oil plus psyllium fiber (CO + PF), and were arranged to a randomized cross over design. Ten subjects consumed controlled diet containing 30% fat calories (20% from test oils and 10% from controlled diet) and 20 g per day of psyllium during fiber supplementation periods. SO + PF diet significantly reduced serum cholesterol compared with SO diet (P < 0.001). CO + PF diet significantly reduced serum cholesterol compared with CO diet (P < 0.014). Hypocholesterolemic response was greater with SO + PF compared with CO + PF (0.36 mmol 1(-1) vs 0.31 mmol 1(-1)). Reductions in low-density lipoprotein (LDL) cholesterol and apolipoprotein (apo) B were parallel to reductions of serum cholesterol. SO diet decreased, while CO diet increased serum cholesterol, LDL cholesterol and apo B. Very-low density lipoprotein cholesterol, high-density lipoprotein cholesterol and apo A-1 were unaffected by psyllium fiber and saturation of fat. Reduction of serum cholesterol was due to reduction of LDL cholesterol. Psyllium fiber supplementation lowered serum cholesterol regardless of saturation level of dietary fat.

Screening and ranking Alberta oil pools for CO{sub 2} flooding and sequestration

Energy Technology Data Exchange (ETDEWEB)

Shaw, J.C. [Adams Pearson Associates Inc., Calgary, AB (Canada); Bachu, S. [Alberta Energy and Utilities Board, Calgary, AB (Canada)

2001-06-01

This paper presented the results of a technical screening program using Excel VBA to successfully screen and rank a very large number of oil pools for enhanced oil recovery using carbon dioxide (CO{sub 2}) flooding. A total of 6 ranking parameters were used, including API gravity of oil, residual oil saturation, ratio between reservoir pressure and minimum miscibility pressure, reservoir temperature, net pay thickness and porosity. The screening program provided a technical ranking of approximately 8,800 Alberta pools in less than 2 minutes. After compilation of the Alberta oil pools, it was determined that most of the deep carbonate oil pools are excellent candidates for CO{sub 2} miscible flooding. Other Devonian carbonate pools were also ranked as having high potential for the process. An environmental benefit of CO{sub 2} miscible flooding process is that carbon sequestration has the potential to reduce anthropogenic carbon dioxide emissions from reaching the atmosphere. Ongoing studies are currently addressing CO{sub 2} capture and transportation, making EOR technology viable for maintaining light oil production in western Canada. 11 refs., 7 tabs., 1 fig.

Tracer monitoring of enhanced oil recovery projects

Directory of Open Access Journals (Sweden)

Kleven R.

2013-05-01

Full Text Available In enhanced oil recovery (EOR, chemicals are injected into the oil reservoir, either to increase macroscopic sweep efficiency, or to reduce remaining oil saturation in swept zones. Tracers can be used to identify reservoirs that are specifically suited for EOR operations. Injection of a selection of partitioning tracers, combined with frequent sample analysis of produced fluids, provides information suited for estimation of residual oil saturation. Tracers can also be used to evaluate and optimize the application of EOR chemicals in the reservoir. Suitable tracers will follow the EOR chemicals and assist in evaluation of retention, degradation or trapping. In addition to field applications, tracers also have a large potential as a tool to perform mechanistic studies of EOR chemicals in laboratory experiments. By labelling EOR chemicals with radioactive isotopes of elements such as H, C and S, detailed studies of transport mechanisms can be carried out. Co-injection of labelled compounds in dynamic flooding experiments in porous media will give information about retention or separation of the unique compounds constituting the chemical formulation. Separation of such compounds may be detrimental to obtaining the EOR effect expected. The paper gives new information of specific methods, and discusses current status for use of tracers in EOR operations.

Crude oil prices : how high, how much harm?

International Nuclear Information System (INIS)

Levesque, M.; Alexander, C.

2002-01-01

This paper discussed the issue of crude oil prices and the economy. Crude oil prices are on the rise due to the recent events in the Middle East. In early April, West Texas Intermediate crude oil climbed to nearly US$28 a barrel. Most of the increase reflects the expectation of stronger world oil demand combined with supply constraints on the part of OPEC. Although there has been some concern expressed that rising oil prices may hinder economic recovery, the authors of this report do not see evidence that rising oil prices would throw economic recovery off course, arguing that the current spike will be short-lived. They stated that even under a worse-case scenario where prices remain inflated, there is little reason to fear for the health of the Canadian economy. OPEC is expected to increase its low production quotas in June. In addition, non-OPEC nations (Russia in particular) are expected to increase oil production in the coming months. The authors also indicated that it is unlikely that conflict in the West Bank will disrupt oil supply because Israel is not an oil-exporting nation. However, oil supply could be affected if other Arab nations were drawn into the issue. It was also noted that military action against Iraq would increase oil prices, possibly as high as US$40 a barrel, but the full extent of this hike in price will probably be unsustainable. In addition, the authors emphasized that the increase in energy costs would not be enough to seriously jeopardize the economic recovery in the United States. As for Canada, it is estimated that a US$10 per barrel increase in crude oil prices would have a small, but positive impact on Canadian GDP because in contrast to the United States, Canada produces much more energy than it consumers. In 2001, Canada ran a trade surplus of $2.8 billion. The report ended by stating that although higher oil prices could add a full percentage point to headline inflation by the end of the year, core inflation is likely to remain

Effects of high fat fish oil and high fat corn oil diets on initiation of AOM-induced colonic aberrant crypt foci in male F344 rats

NARCIS (Netherlands)

Dommels, Y.E.M.; Heemskerk, S.; Berg, H. van den; Alink, G.M.; Bladeren, P.J. van; Ommen, B. van

2003-01-01

Modulating effects of high fat fish oil (HFFO) and high fat corn oil (HFCO) diets on azoxymethane (AOM)-induced colonic aberrant crypt foci (ACF) were studied in male F344 rats following 8 weeks of dietary treatment. The incidence of AOM-induced ACF was significantly lower in the proximal colon of

The impact of high oil prices on natural gas

International Nuclear Information System (INIS)

Koevoet, H.

2003-01-01

The principle of gas-to-oil (oil prices determine the price of natural gas) in the Netherlands and several other developments elsewhere (war in Iraq and a cold winter in the USA) has caused high natural gas prices. The question is whether the liberalization of the energy market can change this principle [nl

Dual Superlyophobic Copper Foam with Good Durability and Recyclability for High Flux, High Efficiency, and Continuous Oil-Water Separation.

Science.gov (United States)

Zhou, Wenting; Li, Song; Liu, Yan; Xu, Zhengzheng; Wei, Sufeng; Wang, Guoyong; Lian, Jianshe; Jiang, Qing

2018-03-21

Traditional oil-water separation materials have to own ultrahigh or ultralow surface energy. Thus, they can only be wetted by one of the two, oil or water. Our experiment here demonstrates that the wettability in oil-water mixtures can be tuned by oil and water initially. Hierarchical voids are built on commercial copper foams with the help of hydrothermally synthesized titanium dioxide nanorods. The foams can be easily wetted by both oil and water. The water prewetted foams are superhydrophilic and superoleophobic under oil-water mixtures, meanwhile the oil prewetted foams are superoleophilic and superhydrophobic. In this paper, many kinds of water-oil mixtures were separated by two foams, prewetted by corresponding oil or water, respectively, combining a straight tee in a high flux, high efficiency, and continuous mode. This research indicates that oil-water mixtures can be separated more eco-friendly and at lower cost.

High internal phase emulsion (HIPE)-templated biopolymeric oleofilms containing an ultra-high concentration of edible liquid oil.

Science.gov (United States)

Wijaya, Wahyu; Van der Meeren, Paul; Dewettinck, Koen; Patel, Ashok R

2018-04-25

We report, for the first time, the fabrication of oleofilms (containing more than 97 wt% edible liquid oil) using high internal phase emulsions (with oil volume fraction φoil = 0.82) as templates. Advanced microscopy studies revealed an interesting microstructure of these films where jammed oil droplets were embedded in a dried matrix of biopolymeric complexes.

Geochemical characteristics of Tertiary saline lacustrine oils in the Western Qaidam Basin, northwest China

International Nuclear Information System (INIS)

Zhu Yangming; Weng Huanxin; Su Aiguo; Liang Digang; Peng Dehua

2005-01-01

Based on the systematic analyses of light hydrocarbon, saturate, aromatic fractions and C isotopes of over 40 oil samples along with related Tertiary source rocks collected from the western Qaidam basin, the geochemical characteristics of the Tertiary saline lacustrine oils in this region was investigated. The oils are characterized by bimodal n-alkane distributions with odd-to-even (C 11 -C 17 ) and even-to-odd (C 18 -C 28 ) predominance, low Pr/Ph (mostly lower than 0.6), high concentration of gammacerane, C 35 hopane and methylated MTTCs, reflecting the high salinity and anoxic setting typical of a saline lacustrine depositional environment. Mango's K 1 values in the saline oils are highly variable (0.99-1.63), and could be associated with the facies-dependent parameters such as Pr/Ph and gammacerane indexes. Compared with other Tertiary oils, the studied Tertiary saline oils are marked by enhanced C 28 sterane abundance (30% or more of C 27 -C 29 homologues), possibly derived from halophilic algae. It is noted that the geochemical parameters of the oils in various oilfields exhibit regular spatial changes, which are consistent with the depositional phase variations of the source rocks. The oils have uncommon heavy C isotopic ratios (-24%o to -26%o) and a flat shape of the individual n-alkane isotope profile, and show isotopic characteristics similar to marine organic matter. The appearance of oleanane and high 24/(24 + 27)-norcholestane ratios (0.57-0.87) in the saline oils and source rocks confirm a Tertiary organic source

Intensification of biodiesel production from soybean oil and waste cooking oil in the presence of heterogeneous catalyst using high speed homogenizer.

Science.gov (United States)

Joshi, Saurabh; Gogate, Parag R; Moreira, Paulo F; Giudici, Reinaldo

2017-11-01

In the present work, high speed homogenizer has been used for the intensification of biodiesel synthesis from soybean oil and waste cooking oil (WCO) used as a sustainable feedstock. High acid value waste cooking oil (27mg of KOH/g of oil) was first esterified with methanol using sulphuric acid as catalyst in two stages to bring the acid value to desired value of 1.5mg of KOH/g of oil. Transesterification of soybean oil (directly due to lower acid value) and esterified waste cooking oil was performed in the presence of heterogeneous catalyst (CaO) for the production of biodiesel. Various experiments were performed for understanding the effect of operating parameters viz. molar ratio, catalyst loading, reaction temperature and speed of rotation of the homogenizer. For soybean oil, the maximum biodiesel yield as 84% was obtained with catalyst loading of 3wt% and molar ratio of oil to methanol of 1:10 at 50°C with 12,000rpm as the speed of rotation in 30min. Similarly biodiesel yield of 88% was obtained from waste cooking oil under identical operating conditions except for the catalyst loading which was 1wt%. Significant increase in the rate of biodiesel production with yields from soybean oil as 84% (in 30min) and from WCO as 88% (30min) was established due to the use of high speed homogenizer as compared to the conventional stirring method (requiring 2-3h for obtaining similar biodiesel yield). The observed intensification was attributed to the turbulence caused at microscale and generation of fine emulsions due to the cavitational effects. Overall it can be concluded from this study that high speed homogenizer can be used as an alternate cavitating device to efficiently produce biodiesel in the presence of heterogeneous catalysts. Copyright © 2017 Elsevier B.V. All rights reserved.

Effects of a very high saturated fat diet on LDL particles in adults with atherogenic dyslipidemia: A randomized controlled trial.

Directory of Open Access Journals (Sweden)

Sally Chiu

Full Text Available Previous studies have shown that increases in LDL-cholesterol resulting from substitution of dietary saturated fat for carbohydrate or unsaturated fat are due primarily to increases in large cholesterol-enriched LDL, with minimal changes in small, dense LDL particles and apolipoprotein B. However, individuals can differ by their LDL particle distribution, and it is possible that this may influence LDL subclass response.The objective of this study was to test whether the reported effects of saturated fat apply to individuals with atherogenic dyslipidemia as characterized by a preponderance of small LDL particles (LDL phenotype B.Fifty-three phenotype B men and postmenopausal women consumed a baseline diet (55%E carbohydrate, 15%E protein, 30%E fat, 8%E saturated fat for 3 weeks, after which they were randomized to either a moderate carbohydrate, very high saturated fat diet (HSF; 39%E carbohydrate, 25%E protein, 36%E fat, 18%E saturated fat or low saturated fat diet (LSF; 37%E carbohydrate, 25%E protein, 37%E fat, 9%E saturated fat for 3 weeks.Compared to the LSF diet, consumption of the HSF diet resulted in significantly greater increases from baseline (% change; 95% CI in plasma concentrations of apolipoprotein B (HSF vs. LSF: 9.5; 3.6 to 15.7 vs. -6.8; -11.7 to -1.76; p = 0.0003 and medium (8.8; -1.3 to 20.0 vs. -7.3; -15.7 to 2.0; p = 0.03, small (6.1; -10.3 to 25.6 vs. -20.8; -32.8 to -6.7; p = 0.02, and total LDL (3.6; -3.2 to 11.0 vs. -7.9; -13.9 to -1.5; p = 0.03 particles, with no differences in change of large and very small LDL concentrations. As expected, total-cholesterol (11.0; 6.5 to 15.7 vs. -5.7; -9.4 to -1.8; p<0.0001 and LDL-cholesterol (16.7; 7.9 to 26.2 vs. -8.7; -15.4 to -1.4; p = 0.0001 also increased with increased saturated fat intake.Because medium and small LDL particles are more highly associated with cardiovascular disease than are larger LDL, the present results suggest that very high saturated fat intake may

Effects of a very high saturated fat diet on LDL particles in adults with atherogenic dyslipidemia: A randomized controlled trial.

Science.gov (United States)

Chiu, Sally; Williams, Paul T; Krauss, Ronald M

2017-01-01

Previous studies have shown that increases in LDL-cholesterol resulting from substitution of dietary saturated fat for carbohydrate or unsaturated fat are due primarily to increases in large cholesterol-enriched LDL, with minimal changes in small, dense LDL particles and apolipoprotein B. However, individuals can differ by their LDL particle distribution, and it is possible that this may influence LDL subclass response. The objective of this study was to test whether the reported effects of saturated fat apply to individuals with atherogenic dyslipidemia as characterized by a preponderance of small LDL particles (LDL phenotype B). Fifty-three phenotype B men and postmenopausal women consumed a baseline diet (55%E carbohydrate, 15%E protein, 30%E fat, 8%E saturated fat) for 3 weeks, after which they were randomized to either a moderate carbohydrate, very high saturated fat diet (HSF; 39%E carbohydrate, 25%E protein, 36%E fat, 18%E saturated fat) or low saturated fat diet (LSF; 37%E carbohydrate, 25%E protein, 37%E fat, 9%E saturated fat) for 3 weeks. Compared to the LSF diet, consumption of the HSF diet resulted in significantly greater increases from baseline (% change; 95% CI) in plasma concentrations of apolipoprotein B (HSF vs. LSF: 9.5; 3.6 to 15.7 vs. -6.8; -11.7 to -1.76; p = 0.0003) and medium (8.8; -1.3 to 20.0 vs. -7.3; -15.7 to 2.0; p = 0.03), small (6.1; -10.3 to 25.6 vs. -20.8; -32.8 to -6.7; p = 0.02), and total LDL (3.6; -3.2 to 11.0 vs. -7.9; -13.9 to -1.5; p = 0.03) particles, with no differences in change of large and very small LDL concentrations. As expected, total-cholesterol (11.0; 6.5 to 15.7 vs. -5.7; -9.4 to -1.8; pvs. -8.7; -15.4 to -1.4; p = 0.0001) also increased with increased saturated fat intake. Because medium and small LDL particles are more highly associated with cardiovascular disease than are larger LDL, the present results suggest that very high saturated fat intake may increase cardiovascular disease risk in phenotype B

Semiconductor saturable absorbers for ultrafast THz signals

DEFF Research Database (Denmark)

Hoffmann, Matthias C.; Turchinovich, Dmitry

We demonstrate saturable absorber behavior of n-type semiconductors in the THz frequency range using nonlinear THz spectroscopy. Further, we observe THz pulse shortening and increase of the group refractive index at high field strengths.......We demonstrate saturable absorber behavior of n-type semiconductors in the THz frequency range using nonlinear THz spectroscopy. Further, we observe THz pulse shortening and increase of the group refractive index at high field strengths....

Microwave assisted saponification (MAS) followed by on-line liquid chromatography (LC)-gas chromatography (GC) for high-throughput and high-sensitivity determination of mineral oil in different cereal-based foodstuffs.

Science.gov (United States)

Moret, Sabrina; Scolaro, Marianna; Barp, Laura; Purcaro, Giorgia; Conte, Lanfranco S

2016-04-01

A high throughput, high-sensitivity procedure, involving simultaneous microwave-assisted extraction (MAS) and unsaponifiable extraction, followed by on-line liquid chromatography (LC)-gas chromatography (GC), has been optimised for rapid and efficient extraction and analytical determination of mineral oil saturated hydrocarbons (MOSH) and mineral oil aromatic hydrocarbons (MOAH) in cereal-based products of different composition. MAS has the advantage of eliminating fat before LC-GC analysis, allowing an increase in the amount of sample extract injected, and hence in sensitivity. The proposed method gave practically quantitative recoveries and good repeatability. Among the different cereal-based products analysed (dry semolina and egg pasta, bread, biscuits, and cakes), egg pasta packed in direct contact with recycled paperboard had on average the highest total MOSH level (15.9 mg kg(-1)), followed by cakes (10.4 mg kg(-1)) and bread (7.5 mg kg(-1)). About 50% of the pasta and bread samples and 20% of the biscuits and cake samples had detectable MOAH amounts. The highest concentrations were found in an egg pasta in direct contact with recycled paperboard (3.6 mg kg(-1)) and in a milk bread (3.6 mg kg(-1)). Copyright © 2015 Elsevier Ltd. All rights reserved.

Corn oil improves the plasma lipoprotein lipid profile compared with extra-virgin olive oil consumption in men and women with elevated cholesterol: results from a randomized controlled feeding trial.

Science.gov (United States)

Maki, Kevin C; Lawless, Andrea L; Kelley, Kathleen M; Kaden, Valerie N; Geiger, Constance J; Dicklin, Mary R

2015-01-01

Restricted intakes of saturated and trans-fatty acids is emphasized in heart-healthy diets, and replacement with poly- and monounsaturated fatty acids is encouraged. To compare the effects of polyunsaturated fatty acid-rich corn oil (CO) and monounsaturated fatty acid-rich extra-virgin olive oil (EVOO) on plasma lipids in men and women (N = 54) with fasting low-density lipoprotein cholesterol (LDL-C) ≥130 mg/dL and consumption away from the clinic. Baseline mean (standard error) lipids in mg/dL were: LDL-C 153.3 (3.5), total cholesterol (total-C) 225.7 (3.9), non-high-density lipoprotein (non-HDL)-C 178.3 (3.7), HDL-C 47.4 (1.7), total-C/HDL-C 5.0 (0.2), and TG 124.8 (7.2). CO resulted in significantly larger least-squares mean % changes (all P Consumption of CO in a weight-maintenance, low saturated fat and cholesterol diet resulted in more favorable changes in LDL-C and other atherogenic lipids vs EVOO. Copyright © 2015 National Lipid Association. Published by Elsevier Inc. All rights reserved.

Nitrogen saturation in stream ecosystems.

Science.gov (United States)

Earl, Stevan R; Valett, H Maurice; Webster, Jackson R

2006-12-01

The concept of nitrogen (N) saturation has organized the assessment of N loading in terrestrial ecosystems. Here we extend the concept to lotic ecosystems by coupling Michaelis-Menten kinetics and nutrient spiraling. We propose a series of saturation response types, which may be used to characterize the proximity of streams to N saturation. We conducted a series of short-term N releases using a tracer (15NO3-N) to measure uptake. Experiments were conducted in streams spanning a gradient of background N concentration. Uptake increased in four of six streams as NO3-N was incrementally elevated, indicating that these streams were not saturated. Uptake generally corresponded to Michaelis-Menten kinetics but deviated from the model in two streams where some other growth-critical factor may have been limiting. Proximity to saturation was correlated to background N concentration but was better predicted by the ratio of dissolved inorganic N (DIN) to soluble reactive phosphorus (SRP), suggesting phosphorus limitation in several high-N streams. Uptake velocity, a reflection of uptake efficiency, declined nonlinearly with increasing N amendment in all streams. At the same time, uptake velocity was highest in the low-N streams. Our conceptual model of N transport, uptake, and uptake efficiency suggests that, while streams may be active sites of N uptake on the landscape, N saturation contributes to nonlinear changes in stream N dynamics that correspond to decreased uptake efficiency.

Estimation of critical gas saturation during pressure depletion in virgin and waterflooded reservoirs

Energy Technology Data Exchange (ETDEWEB)

McDougall, S.R.; Sorbie, K.S. [Heriot-Watt Univ., Dept. of Petroleum Engineering, Edinburgh (United Kingdom)

1999-08-01

An important issue in petroleum engineering is the prediction of gas production during reservoir depletion - either following conventional waterflooding operations or in the early stages of hydrocarbon production. The estimation of critical gas saturation for use in corresponding simulation studies is clearly a primary concern. To this end, a 3D, three-phase numerical pore-scale simulator has been developed that can be used to estimate critical gas saturations over a range of different lengthscales and for a wide range of fluid and rock properties. The model incorporates a great deal of the known physics observed in associated laboratory micromodel experiments, including embryonic nucleation, supersaturation effects, multiphase diffusion, bubble growth/migration/fragmentation, oil shrinkage, and three-phase spreading coefficients. These precise pore-scale mechanisms governing gas evolution have been found to be far more subtle than earlier models would suggest because of the large variation of gas/oil interfacial tension (IFT) with pressure. This has a profound effect upon the migration of gas structures during depletion. In models pertaining to reservoir rock, the process of gas migration is consequently much slower than predictions from more simplistic models would imply. This is the first time that bubble fragmentation and IFT variations have been included in a model of gas evolution at the pore-scale and the implications for production forecasting are expected to be significant. In addition, novel scaling groups have been derived for a number of different facies under both virgin and waterflooded conditions. One future application of these groups would be to scale S{sub gc} values obtained from high rate depressurization experiments to the low rate conditions more characteristic of field operations. (Author)

Environmental Forensics: Molecular Insight into Oil Spill Weathering Helps Advance High Magnetic Field FT-ICR Mass Spectrometry

Science.gov (United States)

McKenna, Amy

2013-03-01

events in the FT-ICR experiment. For example, the high density of peaks at each nominal mass unit provides unprecedented insight into how excitation conditions affect ion motion during detection. Aggregated oil (i.e., tar balls, tar mats) that reached the surface exhibits a more than two-fold increase in the total number of detected species, with an increased number of oxygenated species. Principal component analysis (PCA) applied to two possible source oils (contained within the same ship) and weathered samples provide the first application of FT-ICR MS for source identification. Molecular formulae from parent and weathered oil indicate that the lightest petroleum fractions (saturated hydrocarbons) are the most readily oxidized components, and can serve as a template to determine chemical transformations that occur throughout the water column. The ability to differentiate and catalogue compositional changes that occur to oil after its release into the environment relies heavily on gains achieved in nearly all steps in the FT-ICR mass spectral experiment required to accommodate larger ion populations inherent to heavily weathered crude oil. Here, we present the requirement for FT-ICR MS for comprehensive oil spill characterization, and highlight advances made to FT-ICR MS experimental conditions developed from petroleum characterization. Work supported by DMR-06-54118, NSF CHE-10-49753 (RAPID), BP/The Gulf of Mexico Research Initiative, and the State of Florida

Comparison of chemical characteristics of high oleic acid fraction of moringa oleifera oil with some vegetable oils

International Nuclear Information System (INIS)

Rahman, F.; Nadeem, M.; Zahoor, Y.

2014-01-01

Chemical characteristics of High oleic acid fraction (HOF) of Moringa oleifera oil (MOO) was compared with sunflower, soybean and canola oils. HOF of MOO was obtained by dry fractionation at 0 degree C. Iodine value and C18:1 in HOF increased from 61.55 to 82.47 points and 70.29% to 81.15%, respectively. Cloud point of HOF was 1.1 degree C as compared to 10.2 degree C in MOO. The induction period of HOF was greater than all the vegetable oils tested in this investigation. HOF can be used as a source of edible oil with better health attributes and superior storage stability. (author)

Study of bio-oil and bio-char production from algae by slow pyrolysis

International Nuclear Information System (INIS)

Chaiwong, K.; Kiatsiriroat, T.; Vorayos, N.; Thararax, C.

2013-01-01

This study examined bio-oil and bio-char fuel produced from Spirulina Sp. by slow pyrolysis. A thermogravimetric analyser (TGA) was used to investigate the pyrolytic characteristics and essential components of algae. It was found that the temperature for the maximum degradation, 322 °C, is lower than that of other biomass. With our fixed-bed reactor, 125 g of dried Spirulina Sp. algae was fed under a nitrogen atmosphere until the temperature reached a set temperature between 450 and 600 °C. It was found that the suitable temperature to obtain bio-char and bio-oil were at approximately 500 and 550 °C respectively. The bio-oil components were identified by a gas chromatography/mass spectrometry (GC–MS). The saturated functional carbon of the bio-oil was in a range of heavy naphtha, kerosene and diesel oil. The energy consumption ratio (ECR) of bio-oil and bio-char was calculated, and the net energy output was positive. The ECR had an average value of 0.49. -- Highlights: •Bio-oil and bio-char fuel produced from Spirulina Sp. by slow pyrolysis. •Suitable temperature to obtained bio-oil and bio-char were at about 550 and 500 °C. •Saturated functional carbon of bio-oil was heavy naphtha, kerosene, diesel oil. •ECR had an average value of 0.49

High-rate oil removing scouring agent. Koyubun jokyoyo seirenzai ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Ishihara, K.; Sato, Y. (Dai-Ichi Kogyo Seiyaku Co. Ltd., Kyoto (Japan))

1991-11-01

Fiber forming, scutching and knitting processes in recent years are performed three to five times faster than in the conventional processes. Associated therewith, oil solutions are taken importantly for their stability and workability, such as smoothing properties, heat resistance and abrasion resistance. On the other hand, difficulty is increasing in removing the oils after scutching and knitting. This paper explains basic rinsing activities required in oil removal, and describes various test characteristics and compatibility of various high-rate oil removing scouring agents. An oil-in-water rinsing mechanism relies upon comprehensive actions of a surfactant in wetting, permeation, emulsified dispersion and solubilization. The most importantly taken among them is the emulsifying action, which largely depends upon its chemical structure. Therefore, for a high-rate oil removing scouring agent, creation of activators is required that make the above basic characteristics and activities compatible for various applications. For example, the above product covers a great variety of kinds for diverse applications, based on non-ionic and anion-based activators. 6 figs., 20 tabs.

Oxidative stability, chemical composition and organoleptic properties of seinat (Cucumis melo var. tibish) seed oil blends with peanut oil from China.

Science.gov (United States)

Siddeeg, Azhari; Xia, Wenshui

2015-12-01

Seinat seed oil was blended with peanut oil for the enhancement of stability and chemical characteristics of the blend. The physicochemical properties (relative density, refractive index, free fatty acids, saponification value, iodine value and peroxide value) of seinat seed and peanut oil blends in ratios 95:5, 85:15, 30:70 and 50:50 proportions were evaluated, as well as oxidative stability index, deferential scanning calorimetric (DSC) characteristics and tocopherols content. Results of oil blend showed that there was no negative effect by the addition of seinat seed oil to peanut oil and also had decreased percentages of all saturated fatty acids except stearic acid, conversely, increased the levels of unsaturated fatty acids. As for the sensory evaluation, the panelist results showed that seinat seed oil blends had no significant differences (p blending of seinat seed oil with peanut oil had also increased the stability and tocopherols content. As Sudan is the first producer of seinat oil, blending of seinat seed oil with traditional oil like quality, and may decrease the consumption of other expensive edible oils.

Avocado oil extraction processes: method for cold-pressed high-quality edible oil production versus traditional production

Directory of Open Access Journals (Sweden)

Giacomo Costagli

2015-10-01

Full Text Available Nowadays the avocado fruit (Persea americana Mill. is widely regarded as an important fruit for its nutritional values, as it is rich in vital human nutrients. The avocado fruit is mainly sold fresh on the market, which however trades also a relevant quantity of second-grade fruits with a relatively high oil content. Traditionally, this oil is extracted from dried fruits by means of organic solvents, but a mechanical method is also used in general in locations where drying systems and/or solvent extraction units cannot be installed. These traditional processes yield a grade of oil that needs subsequent refining and is mainly used in the cosmetic industry. In the late 1990s, in New Zeland, a processing company with the collaboration of Alfa Laval began producing cold-pressed avocado oil (CPAO to be sold as edible oil for salads and cooking. Over the last fifteen years, CPAO production has increased in many other countries and has led to an expansion of the market which is set to continue, given the growing interest in highquality and healthy food. Avocado oil like olive oil is extracted from the fruit pulp and in particular shares many principles of the extraction process with extra-vergin olive oil. We conducted a review of traditional and modern extraction methods with particular focus on extraction processes and technology for CPAO production.

Oils; lubricants; paraffin-wax compositions; hydrocarbon condensation products

Energy Technology Data Exchange (ETDEWEB)

1934-04-04

Petroleum hydrocarbons such as gasoline, kerosene, Diesel fuel oil, lubricating-oil, and paraffin wax, and like hydrocarbons such as are obtainable from shale oil and by the hydrogenation of carbonaceous materials, are improved by addition of products obtained by condensing a cyclic hydrocarbon with a saturated dihalogen derivative of an aliphatic hydrocarbon containing less than five carbon atoms. The addition of the condensation products increases the viscosity of the hydrocarbon oils specified, and is particularly useful in the case of lubricating-oils; addition of the condensation products to paraffin wax increases the transparency and adherent properties of the wax, and is useful in the manufacture of moulded articles such as candles; the products may also be used in solid lubricating-compositions.

Genetic control of soybean seed oil: I. QTL and genes associated with seed oil concentration in RIL populations derived from crossing moderately high-oil parents.

Science.gov (United States)

Eskandari, Mehrzad; Cober, Elroy R; Rajcan, Istvan

2013-02-01

Soybean seed is a major source of oil for human consumption worldwide and the main renewable feedstock for biodiesel production in North America. Increasing seed oil concentration in soybean [Glycine max (L.) Merrill] with no or minimal impact on protein concentration could be accelerated by exploiting quantitative trait loci (QTL) or gene-specific markers. Oil concentration in soybean is a polygenic trait regulated by many genes with mostly small effects and which is negatively associated with protein concentration. The objectives of this study were to discover and validate oil QTL in two recombinant inbred line (RIL) populations derived from crosses between three moderately high-oil soybean cultivars, OAC Wallace, OAC Glencoe, and RCAT Angora. The RIL populations were grown across several environments over 2 years in Ontario, Canada. In a population of 203 F(3:6) RILs from a cross of OAC Wallace and OAC Glencoe, a total of 11 genomic regions on nine different chromosomes were identified as associated with oil concentration using multiple QTL mapping and single-factor ANOVA. The percentage of the phenotypic variation accounted for by each QTL ranged from 4 to 11 %. Of the five QTL that were tested in a population of 211 F(3:5) RILs from the cross RCAT Angora × OAC Wallace, a "trait-based" bidirectional selective genotyping analysis validated four QTL (80 %). In addition, a total of seven two-way epistatic interactions were identified for oil concentration in this study. The QTL and epistatic interactions identified in this study could be used in marker-assisted introgression aimed at pyramiding high-oil alleles in soybean cultivars to increase oil concentration for biodiesel as well as edible oil applications.

Saturated Switching Systems

CERN Document Server

Benzaouia, Abdellah

2012-01-01

Saturated Switching Systems treats the problem of actuator saturation, inherent in all dynamical systems by using two approaches: positive invariance in which the controller is designed to work within a region of non-saturating linear behaviour; and saturation technique which allows saturation but guarantees asymptotic stability. The results obtained are extended from the linear systems in which they were first developed to switching systems with uncertainties, 2D switching systems, switching systems with Markovian jumping and switching systems of the Takagi-Sugeno type. The text represents a thoroughly referenced distillation of results obtained in this field during the last decade. The selected tool for analysis and design of stabilizing controllers is based on multiple Lyapunov functions and linear matrix inequalities. All the results are illustrated with numerical examples and figures many of them being modelled using MATLAB®. Saturated Switching Systems will be of interest to academic researchers in con...

ANALYSIS OF THE SPECIAL FEATURES OF THE THERMAL PROCESS IN AN INDUCTION GENERATOR AT HIGH SATURATION OF THE MAGNETIC SYSTEM

Directory of Open Access Journals (Sweden)

V. Chenchevoi

2017-06-01

Full Text Available Purpose. Development of the method for the assessment of the thermal operation modes of an autonomous electrical power system with an induction motor, aiming at improvement of the reliability of electricity supply and the quality of electric energy. Methodology. Induction generator mathematical modeling taking into account the magnetic system saturation was used in the research. A heat model taking into account the excess of the temperature of the induction generator units in the mode of high saturation was developed. The obtained results were compared with the experimental data. Results. The paper contains the solution to the problem of improvement of the mathematical model sand methods for steel losses determination in there search of the operation modes of an autonomous uncontrolled induction generator taking into consideration the properties of the magnetic system in the mode of high saturation. The expression for determination of steel losses in the mode of high saturation is obtained. It enables the assessment of the induction generator thermal condition. Originality. The analytical dependence for the calculation of the steel losses in the mode of magnetic system saturation has been obtained for the first time. Practical value. The obtained expression for the calculation of the steel losses can be used for determination of the admissible time of generator operation at overload. It will allow avoiding broken winding insulation and complete use of the generator overload capacity. As a result, it will reduce possible irregularities of electricity supply due to the generator preliminary cutoff.

Evidence for transfer of radicals between oil-in-water emulsion droplets as detected by the probe (E,E)-3,5-Bis(4-phenyl-1,3-butadienyl)-4,4-difluoro-4-bora-3a,4a-diaza-s-indacene, BODIPY665/676

DEFF Research Database (Denmark)

Raudsepp, Piret; Brüggemann, Dagmar Adeline; Andersen, Mogens Larsen

2014-01-01

(E,E)-3,5-Bis(4-phenyl-1,3-butadienyl)-4,4-difluoro-4-bora-3a,4a-diaza-s-indacene, BODIPY(665/676), is a lipophilic radical-sensitive fluorescent probe that can be used to study radical-driven lipid autoxidation. The sensitivity of BODIPY(665/676) was studied in the presence of radical initiators...... di-tert-butyl peroxide and 2,2'-azobis(2,4-dimethyl)valeronitrile (AMVN). In both cases the fluorescence of BODIPY(665/676) changed more in saturated medium-chain triglyceride oil than in linseed or sunflower oils, where the high degree of unsaturation is expected to give more pronounced radical......-derived lipid oxidation. It was suggested that BODIPY(665/676), as the only available oxidizable substance in the saturated oil, was directly attacked by radicals, resulting in high rates of probe oxidation, while in the unsaturated oils, radicals attacked either unsaturated fatty acids or BODIPY(665...

Withdrawal from high-carbohydrate, high-saturated-fat diet changes saturated fat distribution and improves hepatic low-density-lipoprotein receptor expression to ameliorate metabolic syndrome in rats.

Science.gov (United States)

Hazarika, Ankita; Kalita, Himadri; Kalita, Mohan Chandra; Devi, Rajlakshmi

2017-06-01

The "lipid hypothesis" determined that saturated fatty acid (SFA) raises low-density lipoprotein cholesterol, thereby increasing the risk for metabolic syndrome (MetS). The aim of this study was to investigate the effect of subchronic withdrawal from a high-carbohydrate, high-saturated fat (HCHF) diet during MetS with reference to changes in deleterious SFA (C12:0, lauric acid; C14:0, myristic acid; C16:0, palmitic acid; C18:0, stearic acid) distribution in liver, white adipose tissue (WAT), and feces. MetS induced by prolonged feeding of an HCHF diet in Wistar albino rat is used as a model of human MetS. The MetS-induced rats were withdrawn from the HCHF diet and changed to a basal diet for final 4 wk of the total experimental duration of 16 wk. SFA distribution in target tissues and hepatic low-density lipoprotein receptor (LDLr) expression were analyzed. Analyses of changes in SFA concentration of target tissues indicate that C16:0 and C18:0 reduced in WAT and liver after withdrawal of the HCHF diet. There was a significant (P < 0.001) decrease in fecal C12:0 with HCHF feeding, which significantly (P < 0.01) increased after withdrawal of this diet. Also, an improvement in expression of hepatic LDLr was observed after withdrawal of HCHF diet. The prolonged consumption of an HCHF diet leads to increased SFA accumulation in liver and WAT, decreased SFA excretion, and reduced hepatic LDLr expression during MetS, which is prominently reversed after subchronic withdrawal of the HCHF diet. This can contribute to better understanding of the metabolic fate of dietary SFA during MetS and may apply to the potential reversal of complications by the simple approach of nutritional modification. Copyright © 2017 Elsevier Inc. All rights reserved.

Grinding temperature and energy ratio coefficient in MQL grinding of high-temperature nickel-base alloy by using different vegetable oils as base oil

OpenAIRE

Li Benkai; Li Changhe; Zhang Yanbin; Wang Yaogang; Jia Dongzhou; Yang Min

2016-01-01

Vegetable oil can be used as a base oil in minimal quantity of lubrication (MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force, and a clip-type t...

SUBTASK 1.7 EVALUATION OF KEY FACTORS AFFECTING SUCCESSFUL OIL PRODUCTION IN THE BAKKEN FORMATION, NORTH DAKOTA PHASE II

Energy Technology Data Exchange (ETDEWEB)

Darren D. Schmidt; Steven A. Smith; James A. Sorensen; Damion J. Knudsen; John A. Harju; Edward N. Steadman

2011-10-31

Production from the Bakken and Three Forks Formations continues to trend upward as forecasts predict significant production of oil from unconventional resources nationwide. As the U.S. Geological Survey reevaluates the 3.65 billion bbl technically recoverable estimate of 2008, technological advancements continue to unlock greater unconventional oil resources, and new discoveries continue within North Dakota. It is expected that the play will continue to expand to the southwest, newly develop in the northeastern and northwestern corners of the basin in North Dakota, and fully develop in between. Although not all wells are economical, the economic success rate has been near 75% with more than 90% of wells finding oil. Currently, only about 15% of the play has been drilled, and recovery rates are less than 5%, providing a significant future of wells to be drilled and untouched hydrocarbons to be pursued through improved stimulation practices or enhanced oil recovery. This study provides the technical characterizations that are necessary to improve knowledge, provide characterization, validate generalizations, and provide insight relative to hydrocarbon recovery in the Bakken and Three Forks Formations. Oil-saturated rock charged from the Bakken shales and prospective Three Forks can be produced given appropriate stimulation treatments. Highly concentrated fracture stimulations with ceramic- and sand-based proppants appear to be providing the best success for areas outside the Parshall and Sanish Fields. Targeting of specific lithologies can influence production from both natural and induced fracture conductivity. Porosity and permeability are low, but various lithofacies units within the formation are highly saturated and, when targeted with appropriate technology, release highly economical quantities of hydrocarbons.

Design and implementation of a caustic flooding EOR pilot at Court Bakken heavy oil reservoir

Energy Technology Data Exchange (ETDEWEB)

Xie, J.; Chung, B.; Leung, L. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Nexen Inc., Calgary, AB (Canada)

2008-10-15

Successful waterflooding has been ongoing since 1988 at the Court Bakken heavy oil field in west central Saskatchewan. There are currently 20 injectors and 28 active oil producers in the Court main unit which is owned by Nexen and Pengrowth. The Court pool has an estimated 103.8 mmbbl of original oil in place (OOIP), of which 24 per cent has been successfully recovered after 20 years of waterflooding. A high-level enhanced oil recovery (EOR) screening study was conducted to evaluate other EOR technologies for a heavy oil reservoir of this viscosity range (17 degrees API). Laboratory studies showed that caustic flooding may enhance oil recovery after waterflooding at the Court Bakken heavy oil pool. A single well test demonstrated that caustic injection effectively reduced residual oil saturation. A sector model reservoir simulation revealed that caustic flood could achieve 9 per cent incremental oil recovery in the pilot area. Following the promising laboratory results, a successful caustic flood pilot was implemented at Court heavy oil pool where the major challenges encountered were low reservoir pressure and water channeling. 6 refs., 2 tabs., 6 figs.

Poverty and growth impacts of high oil prices: Evidence from Sri Lanka

International Nuclear Information System (INIS)

Naranpanawa, Athula; Bandara, Jayatilleke S.

2012-01-01

The sharp rise in oil and food prices in 2007 and 2008 caused negative impacts on poverty and economic growth in many oil and food importing developing countries. Some analysts believe that these countries are under stress again due to a rise in crude oil prices, to a two-and-a-half year high in March 2011, which has also been partly responsible for higher food prices in recent months. However, there is a limited body of empirical evidence available from developing countries on the impact of high oil prices on growth in general and household poverty in particular. In this study, Sri Lanka is used as a case study and a computable general equilibrium (CGE) approach is adopted as an analytical framework to explore the growth and poverty impacts of high oil prices. The results suggest that urban low income households are the group most adversely affected by high global oil prices, followed by low income rural households. In contrast, estate low income households are the least affected out of all low income households. The energy intensive manufacturing sector and services sector are affected most compared to the agricultural sector. - Highlights: ► Using a general equilibrium model we find poverty and oil price link for Sri Lanka. ► Urban low income households are the group most adversely affected. ► Energy intensive manufacturing and services sectors are affected most.

Auto Detection For High Level Water Content For Oil Well

Science.gov (United States)

Janier, Josefina Barnachea; Jumaludin, Zainul Arifin B.

2010-06-01

Auto detection of high level water content for oil well is a system that measures the percentage of water in crude oil. This paper aims to discuss an auto detection system for measuring the content of water level in crude oil which is applicable for offshore and onshore oil operations. Data regarding water level content from wells can be determined by using automation thus, well with high water level can be determined immediately whether to be closed or not from operations. Theoretically the system measures the percentage of two- fluid mixture where the fluids have different electrical conductivities which are water and crude oil. The system made use of grid sensor which is a grid pattern like of horizontal and vertical wires. When water occupies the space at the intersection of vertical and horizontal wires, an electrical signal is detected which proved that water completed the circuit path in the system. The electrical signals are counted whereas the percentage of water is determined from the total electrical signals detected over electrical signals provided. Simulation of the system using the MultiSIM showed that the system provided the desired result.

The Danish tax on saturated fat

DEFF Research Database (Denmark)

Jensen, Jørgen Dejgård; Smed, Sinne

2013-01-01

and oils. This assessment is done by conducting an econometric analysis on weekly food purchase data from a large household panel dataset (GfK Consumer Tracking Scandinavia), spanning the period from January 2008 until July 2012.The econometric analysis suggest that the introduction of the tax on saturated...... and fats, a shift that seems to have been utilized by discount chains to raise the prices of butter and margarine by more than the pure tax increase. Due to the relatively short data period with the tax being active, interpretation of these findings from a long-run perspective should be done...... with considerable care. It is thus recommended to repeat – and broaden – the analysis at a later stage, when data are available for a longer period after the introduction of the fat tax....

Structuring oil by protein building blocks

NARCIS (Netherlands)

Vries, de Auke

2017-01-01

Over the recent years, structuring of oil into ‘organogels’ or ‘oleogels’ has gained much attention amongst colloid-, material,- and food scientists. Potentially, these oleogels could be used as an alternative for saturated- and trans fats in food products. To develop oleogels as a

Firetube boiler with high efficiency for producing saturated or superheated steam

Energy Technology Data Exchange (ETDEWEB)

Carosso, V J; Carosso, J Y

1976-10-07

This boiler for producing saturated or super-heated steam is to be manufactured in one piece or in units which can be assembled at site without skilled workers, at the factory. It is to have a high efficiency and dimensions which permit the transport of the completely assembled boiler by road transport. The relatively small water-steam vessel lies across the longitudinal axis of the boiler in the rear boiler space over a battery of preheater tubes. By these measures and by a very detailed and appropriately described rational arrangement of other parts, such as convection bundles, primary and secondary superheater, evaporation tubes, which form an 'evaporation shield', upper and lower longitudinal chambers with vertical connecting pipes of different crossections, the above mentioned condition for space requirement is fulfilled and a high efficiency should be achieved, but with considerable expense.

Studies of non-isothermal flow in saturated and partially saturated porous media

International Nuclear Information System (INIS)

Ho, C.K.; Maki, K.S.; Glass, R.J.

1993-01-01

Physical and numerical experiments have been performed to investigate the behavior of nonisothermal flow in two-dimensional saturated and partially saturated porous media. The physical experiments were performed to identify non-isothermal flow fields and temperature distributions in fully saturated, half-saturated, and residually saturated two-dimensional porous media with bottom heating and top cooling. Two counter-rotating liquid-phase convective cells were observed to develop in the saturated regions of all three cases. Gas-phase convection was also evidenced in the unsaturated regions of the partially saturated experiments. TOUGH2 numerical simulations of the saturated case were found to be strongly dependent on the assumed boundary conditions of the physical system. Models including heat losses through the boundaries of the test cell produced temperature and flow fields that were in better agreement with the observed temperature and flow fields than models that assumed insulated boundary conditions. A sensitivity analysis also showed that a reduction of the bulk permeability of the porous media in the numerical simulations depressed the effects of convection, flattening the temperature profiles across the test cell

Quantitative analysis of ruminal bacterial populations involved in lipid metabolism in dairy cows fed different vegetable oils

DEFF Research Database (Denmark)

Vargas-Bello-Pérez, E.; Cancino-Padilla, N.; Romero, J.

2016-01-01

Vegetable oils are used to increase energy density of dairy cow diets, although they can provoke changes in rumen bacteria populations and have repercussions on the biohydrogenation process. The aim of this study was to evaluate the effect of two sources of dietary lipids: soybean oil (SO......, an unsaturated source) and hydrogenated palm oil (HPO, a saturated source) on bacterial populations and the fatty acid profile of ruminal digesta. Three non-lactating Holstein cows fitted with ruminal cannulae were used in a 3×3 Latin square design with three periods consisting of 21 days. Dietary treatments...... parameters, whereas HPO can increase load of ruminal P. bryantii. Also, results observed in our targeted bacteria may have depended on the saturation degree of dietary oils....

Fatty Amides from Crude Rice Bran Oil as Green Corrosion Inhibitors

Directory of Open Access Journals (Sweden)

E. Reyes-Dorantes

2017-01-01

Full Text Available Due to its high oil content, this research proposes the use of an agroindustrial byproduct (rice bran as a sustainable option for the synthesis of corrosion inhibitors. From the crude rice bran oil, the synthesis of fatty amide-type corrosion inhibitors was carried out. The corrosion inhibitory capacity of the fatty amides was evaluated on an API X-70 steel using electrochemical techniques such as real-time corrosion monitoring and potentiodynamic polarization curves. As a corrosive medium, a CO2-saturated solution (3.5% NaCl was used at three temperatures (30, 50, and 70°C and different concentrations of inhibitor (0, 5, 10, 25, 50, and 100 ppm. The results demonstrate that the sustainable use of agroindustrial byproducts is a good alternative to the synthesis of environmentally friendly inhibitors with high corrosion inhibition efficiencies.

Antibacterial Activity of Essential Oil of Sature jahortensis Against Multi-DrugResistant Bacteria

Directory of Open Access Journals (Sweden)

Saeide Saeidi

2014-05-01

Full Text Available Background: Development of resistance to many of the commonly used antibiotics is an impetus for further attempts to search for new antimicrobial agents. Objectives: In the present study, the antibacterial activity of Saturejahortensis essential oil against multi-drug resistant bacteria isolated from the urinary tract infections was investigated. Materials and Methods: During the years 2011 to 2012 a total of 36 strains of pathogenic bacteria including 12 Klebsiellapneumoniae, 12 Escherichia coli and 12 Staphylococcus aureus species were isolated from urine samples of hospitalized patients (Amir Al-Momenin Hospital, Zabol, South-eastern Iran suffering from urinary tract infections. After bacteriological confirmatory tests, the minimum inhibitory concentrations of the essential oil of Saturejahortensis were determined using micro-dilution method. Results: The antibiotic resistance profile of the E. coli isolates were as follows: ceftazidime (50% cefixime (41.6%, tetracycline (75%, erythromycin (58.3%. However K. pneumoniae isolates showed resistance to ceftazidime (33.3%, cefixime (58.3%, erythromycin (75% and S. aureus isolates were resistant to cefixime (33.3%, trimethoprim-sulfamethoxazole (41.66%, penicillin (50%, oxacillin (83.3%, ceftazidime (66.6% and vancomycin (8.3%. The essential oil of this plant had inhibitory effect against most isolates. More than 1/3 of the E. coli isolates showed the lowest MIC (10 ppm whereas more than 1/3 of the K. pneumoniae isolates showed the highest (250 ppm MIC values. In contrast ,equal number of S. aureus isolates showed the low MIC values (10 and 50 ppm, while the heighest MIC (250 ppm was seen in 1/3 of isolates and moderate MIC (100 ppm was seen in one isolate only. Conclusions: The Saturejahortensis essential oil has a potent antimicrobial activity against multi-drug resistant bacteria. The present study confirms the usefullness of this essential oil as antibacterial agent but further research is

On the saturation of astrophysical dynamos

DEFF Research Database (Denmark)

Dorch, Bertil; Archontis, Vasilis

2004-01-01

In the context of astrophysical dynamos we illustrate that the no-cosines flow, with zero mean helicity, can drive fast dynamo action and we study the dynamo's mode of operation during both the linear and non-linear saturation regimes. It turns out that in addition to a high growth rate in the li......In the context of astrophysical dynamos we illustrate that the no-cosines flow, with zero mean helicity, can drive fast dynamo action and we study the dynamo's mode of operation during both the linear and non-linear saturation regimes. It turns out that in addition to a high growth rate...

IMPACT OF OIL ON THE MECHANICAL PROPERTIES OF SOIL SUBSIDENCE

Directory of Open Access Journals (Sweden)

Алексей Алексеевич Бурцев

2016-08-01

Full Text Available The paper studied the effect of oil content on the mechanical properties of soil subsidence - Ek modulus and compressibility factor m0, obtained in the laboratory with the help of artificial impregnation oil soil samples. A comparison of the above parameters with samples of the same soil in the natural and water-saturated conditions has been perfomed.

Properties and quality verification of biodiesel produced from tobacco seed oil

Energy Technology Data Exchange (ETDEWEB)

Usta, N., E-mail: n_usta@pau.edu.t [Pamukkale University, Mechanical Engineering Department, 20070 Denizli (Turkey); Aydogan, B. [Pamukkale University, Mechanical Engineering Department, 20070 Denizli (Turkey); Con, A.H. [Pamukkale University, Food Engineering Department, 20070 Denizli (Turkey); Uguzdogan, E. [Pamukkale University, Chemical Engineering Department, 20070 Denizli (Turkey); Ozkal, S.G. [Pamukkale University, Food Engineering Department, 20070 Denizli (Turkey)

2011-05-15

Research highlights: {yields} High quality biodiesel fuel can be produced from tobacco seed oil. {yields} Pyrogallol was found to be effective antioxidant improving the oxidation stability. {yields} The iodine number was reduced with a biodiesel including more saturated fatty acids. {yields} Octadecene-1-maleic anhydride copolymer was an effective cold flow improver. {yields} The appropriate amounts of the additives do not affect the properties negatively. -- Abstract: Tobacco seed oil has been evaluated as a feedstock for biodiesel production. In this study, all properties of the biodiesel that was produced from tobacco seed oil were examined and some solutions were derived to bring all properties of the biodiesel within European Biodiesel Standard EN14214 to verify biodiesel quality. Among the properties, only oxidation stability and iodine number of the biodiesel, which mainly depend on fatty acid composition of the oil, were not within the limits of the standard. Six different antioxidants that are tert-butylhydroquinone, butylated hydroxytoluene, propyl gallate, pyrogallol, {alpha}-tocopherol and butylated hydroxyanisole were used to improve the oxidation stability. Among them, pyrogallol was found to be the most effective antioxidant. The iodine number was improved with blending the biodiesel produced from tobacco seed oil with a biodiesel that contains more saturated fatty acids. However, the blending caused increasing the cold filter plugging point. Therefore, four different cold flow improvers, which are ethylene-vinyl acetate copolymer, octadecene-1-maleic anhydride copolymer and two commercial cold flow improvers, were used to decrease cold filter plugging point of the biodiesel and the blends. Among the improvers, the best improver is said to be octadecene-1-maleic anhydride copolymer. In addition, effects of temperature on the density and the viscosity of the biodiesel were investigated.

Red palm oil: nutritional, physiological and therapeutic roles in improving human wellbeing and quality of life.

Science.gov (United States)

Oguntibeju, O O; Esterhuyse, A J; Truter, E J

2009-01-01

The link between dietary fats and cardiovascular disease has created a growing interest in dietary red palm oil research. Also, the link between nutrition and health, oxidative stress and the severity or progression of disease has stimulated further interest in the potential role of red palm oil (a natural antioxidant product) to improve oxidative status by reducing oxidative stress in patients with cardiovascular disease, cancer and other chronic diseases. In spite of its level of saturated fatty acid content (50%), red palm oil has not been found to promote atherosclerosis and/or arterial thrombosis. This is probably due to the ratio of its saturated fatty acid to unsaturated fatty acid content and its high concentration of antioxidants such as beta-carotene, tocotrienols, tocopherols and vitamin E. It has also been reported that the consumption of red palm oil reduces the level of endogenous cholesterol, and this seems to be due to the presence of the tocotrienols and the peculiar isomeric position of its fatty acids. The benefits of red palm oil to health include a reduction in the risk of arterial thrombosis and/or atherosclerosis, inhibition of endogenous cholesterol biosynthesis, platelet aggregation, a reduction in oxidative stress and a reduction in blood pressure. It has also been shown that dietary red palm oil, taken in moderation in animals and humans, promotes the efficient utilisation of nutrients, activates hepatic drug metabolising enzymes, facilitates the haemoglobinisation of red blood cells and improves immune function. This review provides a comprehensive overview of the nutritional, physiological and biochemical roles of red palm oil in improving wellbeing and quality of life.

The use of stability indices in predicting asphaltene problems in upstream and downstream oil operations

Energy Technology Data Exchange (ETDEWEB)

Asomaning, S. [Baker Petrolite, Sugar Land, TX (United States)

2003-07-01

A series of test methods have been developed to determine the stability of asphaltenes in crude oils. They were developed due to the high cost of remediating asphaltene deposition in offshore operations. This study described the characteristics of the Oliensis Spot Test, two saturates, aromatics, resins and asphaltenes (SARA)-based screens (the Colloidal Instability Index and Asphaltene-Resin ratio), a solvent titration method with near infrared radiation (NIR) solids detection, and live oil depressurization. Each method is used to predict the stability of asphaltenes in crude oils with different API gravity. A complete description of the test methods was provided along with experimental data. The effectiveness of the different tests in predicting the stability of asphaltenes in crude oils was also assessed. Results indicate that the prediction of a crude oil's tendency towards asphaltene precipitation was more accurate with the Colloidal Instability Index and the solvent titration method. Live oil depressurization proved to be very effective in predicting the stability of asphaltenes for light oils, where most stability tests fail. tabs., figs.

Modulation of the Gut Microbiota by Krill Oil in Mice Fed a High-Sugar High-Fat Diet

Directory of Open Access Journals (Sweden)

Chenyang Lu

2017-05-01

Full Text Available Multiple lines of evidence suggest that the gut microbiota plays vital roles in metabolic diseases such as hyperlipidemia. Previous studies have confirmed that krill oil can alleviate hyperlipidemia, but the underlying mechanism remains unclear. To discern whether krill oil changes the structure of the gut microbiota during the hyperlipidemia treatment, 72 mice were acclimatized with a standard chow diet for 2 weeks and then randomly allocated to receive a standard chow diet (control group, n = 12 or a high-sugar-high-fat (HSHF diet supplemented with a low (100 μg/g·d, HSHF+LD group, n = 12, moderate (200 μg/g·d, HSHF+MD group, n = 12 or high dosage of krill oil (600 μg/g·d, HSHF+HD group, n = 12, simvastatin (HSHF+S group, n = 12 or saline (HSHF group, n = 12 continuously for 12 weeks. The resulting weight gains were attenuated, the liver index and the low-density lipoprotein, total cholesterol and triglyceride concentrations showed a stepwise reduction in the treated groups compared with those of the control group. A dose-dependent modulation of the gut microbiota was observed after treatment with krill oil. Low- and moderate- doses of krill oil increased the similarity between the composition of the HSHF diet-induced gut microbiota and that of the control, whereas the mice fed the high-dose exhibited a unique gut microbiota structure that was different from that of the control and HSHF groups. Sixty-five key operational taxonomic units (OTUs that responded to the krill oil treatment were identified using redundancy analysis, of which 26 OTUs were increased and 39 OTUs were decreased compared with those of the HSHF group. In conclusion, the results obtained in this study suggest that the structural alterations in the gut microbiota induced by krill oil treatment were dose-dependent and associated with the alleviation of hyperlipidemia. Additionally, the high-dose krill oil treatment showed combined effects on the alleviation of

Sequential enrichment of microbial population exhibiting enhanced biodegradation of crude oil

International Nuclear Information System (INIS)

Venkateswaran, Kasthuri; Harayama, Shigeaki.

1995-01-01

The distribution of oil-degrading bacteria in the coastal waters and sediments of Hokkaido, Japan, was surveyed. It was found that the potential of mixed microbial populations to degrade weathered crude oil was not confined to any ecological components (water or sediment) nor to the sampling stations. One microbial culture that was stable during repeated subculturing degraded 45% of the saturates and 20% of the aromatics present in crude oil in 10 days during the initial screening. The residual hydrocarbons in this culture were extracted by chloroform and dispersed in a fresh seawater-based medium and subsequently inoculated with microorganisms from the first culture. After full growth of the second culture, the residual hydrocarbons were extracted and dispersed in a fresh medium in which microorganisms from the second culture had been inoculated. This sequential process was carried out six times to enrich those microorganisms that grew on the recalcitrant components of crude oil. After repeated exposure of the residual crude oil to the enriched microorganisms, about 80% of the initially added crude oil was degraded. The cultures obtained after each enrichment cycle were kept, and the degradation of fresh crude oil by the enriched microorganisms was monitored. The degrading activity of the enriched cultures increased as the number of enrichment cycles increased. A microbial population that had been selected six times on the residual crude oil could degrade 70% of the saturates and 30% of the aromatics of crude oil, indicating that growth of a microbial population on residual crude oil improved its ability to biodegrade crude oil. 21 refs., 2 tabs., 7 figs

Enhancement of oleic acid in butter oil by high oleic fraction of moringa oleifera oil

International Nuclear Information System (INIS)

Nadeem, M.; Ullah, R.

2016-01-01

Oleic acid in butter oil (BO) was enhanced by a high oleic acid fraction (HOF) of Moringa oleifera oil (MOO). HOF was blended with BO at four different concentrations i.e. 5%, 10 percent, 15% and 20% (HOF-5, HOF-10, HOF-15 and HOF-20, respectively), compared with a control (BO). The oleic acid in HOF increased from 71.55 percent to 80.25%. DPPH free radical scavenging activity and total flavonoid content of HOF was 76.88% and 34.52 mg/100 g. Supplementation of butter oil with 20% HOF, decreased the cholesterol from 224 to 177 mg/100 g. Peroxide value of three months stored HOF-20 was 1.18 (meqO/sub 2/ kg) as compared to control, 3.15 (meqO/sub 2/kg). Induction period of HOF-20 was 4.07 h greater than control. These results evidenced that oleic acid in butter oil can be substantially increased by HOF of MOO. (author)

Method for purification of combustible oils, adapted particularly for diesel motors

Energy Technology Data Exchange (ETDEWEB)

1942-01-13

A method is described for the purification of oils for diesel motors from mixtures of tar oils, predominantly aromatic with aliphatic hydrocarbon oils by treatment with refining means which are dissolved in organic solvents and mixed with the oil to be purified and also with water; separation of the separate impurities and washing of the material of treatment with water characcterized by the fact that this refining agent used consists of monobasic and polybasic organic acids, saturated or unsaturated, and also their anhydrides, and substituted acids and their anhydrides.

Effect of Gamma Irradiation Doses on Some Chemical Characteristics of Cotton Seed Oil

International Nuclear Information System (INIS)

Saleh, O.I.

2011-01-01

Cotton Seeds c.v. Giza 85 (Gossypium hirsutum L.) were exposed to gamma irradiation doses of 0.5, 1.0 and 1.5 kGy to improve some chemical characteristics of cotton seed oil i.e. saturated and unsaturated fatty acids, gossypol and βsitosterol that were bound oil. The presented study showed that, the saturated fatty acids; lauric, palmitic and stearic increased when the cotton seeds were exposed to gamma irradiation doses of 0.5 up to 1.5 kGy, On the other hand, arachidic acid content decreased in all the irradiated treatments compared with untreated cotton seed. The unsaturated fatty acid oleic was increased in irradiated cotton seed samples compared with untreated one, while linoleic, the major unsaturated fatty acid decreased in irradiated cotton seed oil than untreated seeds. Gossypol and βsitosterol, bound oil, in irradiated cotton seeds increased gradually with gamma irradiated doses compared with untreated control samples

Krill Oil Ameliorates Mitochondrial Dysfunctions in Rats Treated with High-Fat Diet

Directory of Open Access Journals (Sweden)

Alessandra Ferramosca

2015-01-01

Full Text Available In recent years, several studies focused their attention on the role of dietary fats in the pathogenesis of hepatic steatosis. It has been demonstrated that a high-fat diet is able to induce hyperglycemia, hyperinsulinemia, obesity, and nonalcoholic fatty liver disease. On the other hand, krill oil, a novel dietary supplement of n-3 PUFAs, has the ability to improve lipid and glucose metabolism, exerting possible protective effects against hepatic steatosis. In this study we have investigated the effects of krill oil on mitochondrial energetic metabolism in animals fed a high-fat diet. To this end, male Sprague-Dawley rats were divided into three groups and fed for 4 weeks with a standard diet (control group, a diet with 35% fat (HF group, or a high-fat diet supplemented with 2.5% krill oil (HF+KO group. The obtained results suggest that krill oil promotes the burning of fat excess introduced by the high-fat diet. This effect is obtained by stimulating mitochondrial metabolic pathways such as fatty acid oxidation, Krebs cycle, and respiratory chain complexes activity. Modulation of the expression of carrier proteins involved in mitochondrial uncoupling was also observed. Overall, krill oil counteracts the negative effects of a high-fat diet on mitochondrial energetic metabolism.

Krill Oil Ameliorates Mitochondrial Dysfunctions in Rats Treated with High-Fat Diet.

Science.gov (United States)

Ferramosca, Alessandra; Conte, Annalea; Zara, Vincenzo

2015-01-01

In recent years, several studies focused their attention on the role of dietary fats in the pathogenesis of hepatic steatosis. It has been demonstrated that a high-fat diet is able to induce hyperglycemia, hyperinsulinemia, obesity, and nonalcoholic fatty liver disease. On the other hand, krill oil, a novel dietary supplement of n-3 PUFAs, has the ability to improve lipid and glucose metabolism, exerting possible protective effects against hepatic steatosis. In this study we have investigated the effects of krill oil on mitochondrial energetic metabolism in animals fed a high-fat diet. To this end, male Sprague-Dawley rats were divided into three groups and fed for 4 weeks with a standard diet (control group), a diet with 35% fat (HF group), or a high-fat diet supplemented with 2.5% krill oil (HF+KO group). The obtained results suggest that krill oil promotes the burning of fat excess introduced by the high-fat diet. This effect is obtained by stimulating mitochondrial metabolic pathways such as fatty acid oxidation, Krebs cycle, and respiratory chain complexes activity. Modulation of the expression of carrier proteins involved in mitochondrial uncoupling was also observed. Overall, krill oil counteracts the negative effects of a high-fat diet on mitochondrial energetic metabolism.

Effect of thermal management on the properties of saturable absorber mirrors in high-power mode-locked semiconductor disk lasers

International Nuclear Information System (INIS)

Rantamäki, Antti; Lyytikäinen, Jari; Jari Nikkinen; Okhotnikov, Oleg G

2011-01-01

The thermal management of saturable absorbers is shown to have a critical impact on a high-power mode-locked disk laser. The absorber with efficient heat removal makes it possible to generate ultrashort pulses with high repetition rates and high power density.

Detection of plant oil DNA using high resolution melting (HRM) post PCR analysis: a tool for disclosure of olive oil adulteration.

Science.gov (United States)

Vietina, Michelangelo; Agrimonti, Caterina; Marmiroli, Nelson

2013-12-15

Extra virgin olive oil is frequently subjected to adulterations with addition of oils obtained from plants other than olive. DNA analysis is a fast and economic tool to identify plant components in oils. Extraction and amplification of DNA by PCR was tested in olives, in milled seeds and in oils, to investigate its use in olive oil traceability. DNA was extracted from different oils made of hazelnut, maize, sunflower, peanut, sesame, soybean, rice and pumpkin. Comparing the DNA melting profiles in reference plant materials and in the oils, it was possible to identify any plant components in oils and mixtures of oils. Real-Time PCR (RT-PCR) platform has been added of the new methodology of high resolution melting (HRM), both were used to analyse olive oils mixed with different percentage of other oils. Results showed HRM a cost effective method for efficient detection of adulterations in olive oils. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effectiveness of Biodiesel from Various Tropical Oil Crops on Lubricity Improvement of Ultra Low Sulfur Diesel (ULSD)

Energy Technology Data Exchange (ETDEWEB)

Chollacoop, Nuwong; Topaiboul, Subongkoj; Goodwin, Vituruch (Bioenergy Group, National Metal and Materials Technology Center (MTEC), Thailand Science Park, Pathumthani, 12120 (Thailand)). e-mail: nuwongc@mtec.or.th

2008-10-15

Ultra low sulfur diesel (ULSD) has been introduced worldwide with an aim to reduce emission. Since the desulfurization process for ULSD inadvertently reduces its lubricity, lubricity additive is needed. Biodiesel emerges as a potential candidate due to its excellent lubricity property and little sulfur content. In the present study, biodiesel from various energy crops available in Thailand was added at various amounts to ULSD to test the lubricity according to the CEC-F-06-A-96 standard (using High-Frequency Reciprocating Rig: HFRR [1]). It was found that when biodiesel from crude palm, jatropha, soybean, coconut, sunflower, rice, corn and sesame oils of less than 1% (by volume) is additized to ULSD, the lubricity is improved to meet the diesel standard. Further addition beyond 2% (by volume) does not improve lubricity remarkably, where the lubrication seems to saturate. Biodiesel improves lubricity property by film formation preventing mechanical contact between the rubbing surfaces, and the effectiveness varies among different feedstock oils. Biodiesel from crude palm oil, jatropha oil and coconut oil seemingly are superior lubricity additives in ULSD than that from soybean oil, sunflower oil, rice oil, corn oil and sesame oil. Keywords: biodiesel, bio-lubricants, palm oil, sunflower oil

CGC/saturation approach for soft interactions at high energy: long range rapidity correlations

International Nuclear Information System (INIS)

Gotsman, E.; Maor, U.; Levin, E.

2015-01-01

In this paper we continue our program to construct a model for high energy soft interactions that is based on the CGC/saturation approach. The main result of this paper is that we have discovered a mechanism that leads to large long range rapidity correlations and results in large values of the correlation function R(y 1 , y 2 ) ≥ 1, which is independent of y 1 and y 2 . Such a behavior of the correlation function provides strong support for the idea that at high energies the system of partons that is produced is not only dense but also has strong attractive forces acting between the partons. (orig.)

Interfacial behaviour between oil/water systems using ionic surfactants from regional vegetable industry and animal pet

Energy Technology Data Exchange (ETDEWEB)

Santos, Francisco Klebson G.; Alves, Juan V.A.; Dantas, Tereza N. Castro; Dutra Junior, Tarcilio V.; Barros Neto, Eduardo L. [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)

2008-07-01

Interfacial tension (IFT) is one of the most important physical properties in the study of fluid-fluid interfaces. In this research the surfactants - saponified coconut oil, saponified castor oil, saponified soybean oil, saponified sunflower oil and basis soap - were synthesized in laboratory, using carboxylic acids from regional industry and animal fat (bovine fat). This study focuses on the search of a high-efficient, low-cost, and safe for the environment flooding system to be applied in enhanced oil recovery. The principal aim of this work is the obtaining of interfacial tensions between oil/water systems, using the developed ionic surfactants. Results showed that the studied surfactants are able to reduce the IFT between oil and brine. The surfactant that was more effective in reducing the IFT value was the one from animal fat. The composition, as well as the kind of the bond, as saturated or unsaturated, of the surfactants has influence in the IFT value. The ionic surfactants from regional industry and animal fat besides presenting low cost propitiate very low interfacial tensions between oil and brine, favoring the interactions with residual oil and thus increasing oil recovery. (author)

Serum lipids, apoproteins and nutrient intake in rural Cretan boys consuming high-olive-oil diets.

NARCIS (Netherlands)

Aravanis, C.; Mensink, R.P.; Karalias, N.; Christodoulou, B.; Kafatos, A.; Katan, M.B.

1988-01-01

A high intake of olive oil has produced high levels of high-density and low levels of low-density lipoprotein cholesterol in short-term dietary trials. To investigate long-term effects of olive oil we have studied the diet and serum lipids of boys in Crete, where a high olive oil consumption is the

Forecasting short-run crude oil price using high- and low-inventory variables

International Nuclear Information System (INIS)

Ye, Michael; Zyren, John; Shore, Joanne

2006-01-01

Since inventories have a lower bound or a minimum operating level, economic literature suggests a nonlinear relationship between inventory level and commodity prices. This was found to be the case in the short-run crude oil market. In order to explore this inventory-price relationship, two nonlinear inventory variables are defined and derived from the monthly normal level and relative level of OECD crude oil inventories from post 1991 Gulf War to October 2003: one for the low inventory state and another for the high inventory state of the crude oil market. Incorporation of low- and high-inventory variables in a single equation model to forecast short-run WTI crude oil prices enhances the model fit and forecast ability

Satellite and airborne oil spill remote sensing: State of the art and application to the BP DeepWater Horizon oil spill

Science.gov (United States)

Leifer, I.; Clark, R.; Jones, C.; Holt, B.; Svejkovsky, J.; Swayze, G.

2011-01-01

The vast, persistent, and unconstrained oil release from the DeepWater Horizon (DWH) challenged the spill response, which required accurate quantitative oil assessment at synoptic and operational scales. Experienced observers are the mainstay of oil spill response. Key limitations are weather, scene illumination geometry, and few trained observers, leading to potential observer bias. Aiding the response was extensive passive and active satellite and airborne remote sensing, including intelligent system augmentation, reviewed herein. Oil slick appearance strongly depends on many factors like emulsion composition and scene geometry, yielding false positives and great thickness uncertainty. Oil thicknesses and the oil to water ratios for thick slicks were derived quantitatively with a new spectral library approach based on the shape and depth of spectral features related to C-H vibration bands. The approach used near infrared, imaging spectroscopy data from the AVIRIS (Airborne Visual/InfraRed Imaging Spectrometer) instrument on the NASA ER-2 stratospheric airplane. Extrapolation to the total slick used MODIS satellite visual-spectrum broadband data, which observes sunglint reflection from surface slicks; i.e., indicates the presence of oil and/or surfactant slicks. Oil slick emissivity is less than seawater's allowing MODIS thermal infrared (TIR) nighttime identification; however, water temperature variations can cause false positives. Some strong emissivity features near 6.7 and 9.7 ??m could be analyzed as for the AVIRIS short wave infrared features, but require high spectral resolution data. TIR spectral trends can allow fresh/weathered oil discrimination. Satellite Synthetic Aperture Radar (SSAR) provided synoptic data under all-sky conditions by observing oil dampening of capillary waves; however, SSAR typically cannot discriminate thick from thin oil slicks. Airborne UAVSAR's significantly greater signal-to-noise ratio and fine spatial resolution allowed

Studies on the hypolipidemic effects of Coconut oil when blended with Tiger nut oil and fed to albino rats

Directory of Open Access Journals (Sweden)

El-Anany, A. M.

2012-09-01

Full Text Available Hyperlipidemia is a predominant risk factor for atherosclerosis and associated cardiovascular diseases (CVD. The international guidelines issued by the World Health Organization recommend a reduction in dietary saturated fat and cholesterol intake as a means to prevent hypercholesterolemia and CVD. The main objective of the current investigation was to evaluate the effects of feeding blended oils consisting of coconut oil (CNO with different proportions of Tiger nut oil (TNO on serum lipid levels in Albino rats. GLC analysis was performed to illustrate the fatty acid composition of the blended oils. Blended oils were obtained by mixing tiger nut oil with coconut oil at the volume ratios of 100:0, 70:30, 50:50, 25:75, 10:90 and 0:100. Fifty-six male albino rats were randomly divided into 7 groups of 8 rats each according to the oil type. The blended oils were fed to rats for a period of up to 10 weeks. Total cholesterol (T-Ch, high-density lipoprotein cholesterol (HDL-Ch, low-density lipoprotein cholesterol (LDL-Ch, and triglycerides (TG, were determined. The atherogenic Index (AI was calculated. The results showed that non-significant changes in all nutritional parameters were observed between the control group and the rats fed with the tested oils. The results also indicate that coconut oil had 86% saturated fatty acids. On TNO contains 66% oleic acid. Therefore, blending coconut oil with tiger nut oil can reduce the proportions of saturated to unsaturated fatty acids in CNO. The rats that were fed blended oils showed significantly reduced levels of serum cholesterol as compared to those fed CNO. The HDL levels were marginally enhanced in the rats that were fed blended oils. The total cholesterol and LDL cholesterol levels were controlled when TNO/CNO proportions varied between 25/75 and 70/30. This was reflected in the calculation of the atherogenic index. Similar changes were observed with serum triglyceride levels.

La hiperlipidemia

Efficiency of preliminary discharge of stratum water in Tuymazinskoe oil field

Science.gov (United States)

Almukhametova, E. M.; Akimov, A. V.; Kalinina, S. V.; Fatkullin, I. F.; Gizetdinov, I. A.

2017-10-01

The high water content of oil is a common occurrence for many Russian fields at the late stage of development. Due to the elimination of associated water in oil, the overload of field pipelines often takes place. Products are often collected by a one-pipe system, which means that the formation water is discharged using special plants PWDS. Research workers have made it clear that the complexity of production “BashNIPIneft” and OGPD “Tuymazaneft” on Tuimazy field was due to the fact that the collection of production, in most cases, uses a centralized system, which loses its advantages when there is a large content of water in the emulsions. Research has indicated that the reagents, used in the field, proved to be ineffective, as the oil of Devonian formations is heavily saturated with paraffins. But, ultimately, the most effective agents for the destruction of emulsions have been nonetheless identified. This paper describes the implementation of the system of track discharge of formation water, which is currently in use for many oil companies not only in Russia but also worldwide.

Energy dependent saturable and reverse saturable absorption in cube-like polyaniline/polymethyl methacrylate film

Energy Technology Data Exchange (ETDEWEB)

Thekkayil, Remyamol [Department of Chemistry, Indian Institute of Space Science and Technology, Valiamala, Thiruvananthapuram 695 547 (India); Philip, Reji [Light and Matter Physics Group, Raman Research Institute, C.V. Raman Avenue, Bangalore 560 080 (India); Gopinath, Pramod [Department of Physics, Indian Institute of Space Science and Technology, Valiamala, Thiruvananthapuram 695 547 (India); John, Honey, E-mail: honey@iist.ac.in [Department of Chemistry, Indian Institute of Space Science and Technology, Valiamala, Thiruvananthapuram 695 547 (India)

2014-08-01

Solid films of cube-like polyaniline synthesized by inverse microemulsion polymerization method have been fabricated in a transparent PMMA host by an in situ free radical polymerization technique, and are characterized by spectroscopic and microscopic techniques. The nonlinear optical properties are studied by open aperture Z-scan technique employing 5 ns (532 nm) and 100 fs (800 nm) laser pulses. At the relatively lower laser pulse energy of 5 μJ, the film shows saturable absorption both in the nanosecond and femtosecond excitation domains. An interesting switchover from saturable absorption to reverse saturable absorption is observed at 532 nm when the energy of the nanosecond laser pulses is increased. The nonlinear absorption coefficient increases with increase in polyaniline concentration, with low optical limiting threshold, as required for a good optical limiter. - Highlights: • Synthesized cube-like polyaniline nanostructures. • Fabricated polyaniline/PMMA nanocomposite films. • At 5 μJ energy, saturable absorption is observed both at ns and fs regime. • Switchover from SA to RSA is observed as energy of laser beam increases. • Film (0.1 wt % polyaniline) shows high β{sub eff} (230 cm GW{sup −1}) and low limiting threshold at 150 μJ.

Selective Hydrodeoxygenation of Vegetable Oils and Waste Cooking Oils to Green Diesel Using a Silica-Supported Ir-ReOx Bimetallic Catalyst.

Science.gov (United States)

Liu, Sibao; Simonetti, Trent; Zheng, Weiqing; Saha, Basudeb

2018-05-09

High yields of diesel-range alkanes are prepared by hydrodeoxygenation of vegetable oils and waste cooking oils over ReO x -modified Ir/SiO 2 catalysts under mild reaction conditions. The catalyst containing a Re/Ir molar ratio of 3 exhibits the best performance, achieving 79-85 wt % yield of diesel-range alkanes at 453 K and 2 MPa H 2 . The yield is nearly quantitative for the theoretical possible long-chain alkanes on the basis of weight of the converted oils. The catalyst retains comparable activity upon regeneration through calcination. Control experiments using probe molecules as model substrates suggest that C=C bonds of unsaturated triglycerides and free fatty acids are first hydrogenated to their corresponding saturated intermediates, which are then converted to aldehyde intermediates through hydrogenolysis of acyl C-O bonds and subsequently hydrogenated to fatty alcohols. Finally, long-chain alkanes without any carbon loss are formed by direct hydrogenolysis of the fatty alcohols. Small amounts of alkanes with one carbon fewer are also formed by decarbonylation of the aldehyde intermediates. A synergy between Ir and partially reduced ReO x sites is discussed to elucidate the high activity of Ir-ReO x /SiO 2. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

High saturation magnetization FeB(C) nanocapsules

International Nuclear Information System (INIS)

Ma, S.; Si, P.Z.; Zhang, Y.; Wu, B.; Li, Y.B.; Liu, J.J.; Feng, W.J.; Ma, X.L.; Zhang, Z.D.

2007-01-01

FeB(C) nanocapsules were prepared by arc-discharging Fe 80 B 20 alloy in Ar and CH 4 . X-ray diffraction and transmission electron microscopy analyses showed that the FeB(C) nanocapsules had a core-shell structure with α-Fe and Fe 3 B as cores and graphite as shells. The formation mechanism of the FeB(C) nanocapsules is discussed. The graphite shells display a strong anti-acid effect. The saturation magnetization at room temperature of the FeB(C) nanocapsules is much higher than that of Fe(B) nanocapsules. The blocking temperature of FeB(C) nanocapsules is above 300 K

The freshwater biodegradation potential of nine Alaskan oils

International Nuclear Information System (INIS)

Blenkinsopp, S.; Segy, G.

1997-01-01

Nine Alaskan representative crude oils and oil products with freshwater spill potential were collected, aged, and incubated in the presence of the standard freshwater inoculum for 28 days at 10 degrees C. Detailed analytical chemistry was performed on all samples to quantify compositional changes. All of the samples tested exhibited measurable hydrocarbon loss as a result of incubation with the freshwater inoculum. Total saturate and total n-alkane biodegradation were greatly enhanced when nutrients were present. The oil products Jet B Fuel and Diesel No. 2 appear to be more biodegradable than the Alaska North Slope and Cook Inlet crude oils tested, while the Bunker C/Diesel mixture appears to be less biodegradable than these crude oils. These results suggest that the screening procedures described here can provide useful information when applying bioremediation technology to the cleanup of selected oiled freshwater environments. 10 refs., 5 tabs., 13 figs

Microscopic analysis of saturable absorbers: Semiconductor saturable absorber mirrors versus graphene

Energy Technology Data Exchange (ETDEWEB)

Hader, J.; Moloney, J. V. [Nonlinear Control Strategies, Inc., 3542 N. Geronimo Ave., Tucson, Arizona 85705 (United States); College of Optical Sciences, University of Arizona, Tucson, Arizona 85721 (United States); Yang, H.-J.; Scheller, M. [College of Optical Sciences, University of Arizona, Tucson, Arizona 85721 (United States); Koch, S. W. [Department of Physics and Materials Sciences Center, Philipps Universität Marburg, Renthof 5, 35032 Marburg (Germany)

2016-02-07

Fully microscopic many-body calculations are used to study the influence of strong sub-picosecond pulses on the carrier distributions and corresponding optical response in saturable absorbers used for mode-locking—semiconductor (quantum well) saturable absorber mirrors (SESAMs) and single layer graphene based saturable absorber mirrors (GSAMs). Unlike in GSAMs, the saturation fluence and recovery time in SESAMs show a strong spectral dependence. While the saturation fluence in the SESAM is minimal at the excitonic bandgap, the optimal recovery time and least pulse distortion due to group delay dispersion are found for excitation higher in the first subband. For excitation near the SESAM bandgap, the saturation fluence is about one tenth of that in the GSAM. At energies above the bandgap, the fluences in both systems become similar. A strong dependence of the saturation fluence on the pulse width in both systems is caused by carrier relaxation during the pulse. The recovery time in graphene is found to be about two to four times faster than that in the SESAMs. The occurrence of negative differential transmission in graphene is shown to be caused by dopant related carriers. In SESAMs, a negative differential transmission is found when exciting below the excitonic resonance where excitation induced dephasing leads to an enhancement of the absorption. Comparisons of the simulation data to the experiment show a very good quantitative agreement.

Neste Oy starts the production of extra high viscosity index lubricating oil in Porvoo

International Nuclear Information System (INIS)

Kilander, H.

1997-01-01

Neste Oy is starting the manufacture of basic oil, used in advanced motor lubricants, in Finland. The plant will start the manufacture of the EHVI (Extra High Viscosity) by the end of 1997. The EHVI basic oil is a synthetic-like oil product, suitable for manufacture of high-quality lubricants. In the beginning the production of the basic oil will be about 50 000 tons/a. The investment costs of the plants are 180 million FIM

Coconut Oil Aggravates Pressure Overload-Induced Cardiomyopathy without Inducing Obesity, Systemic Insulin Resistance, or Cardiac Steatosis.

Science.gov (United States)

Muthuramu, Ilayaraja; Amin, Ruhul; Postnov, Andrey; Mishra, Mudit; Jacobs, Frank; Gheysens, Olivier; Van Veldhoven, Paul P; De Geest, Bart

2017-07-18

Studies evaluating the effects of high-saturated fat diets on cardiac function are most often confounded by diet-induced obesity and by systemic insulin resistance. We evaluated whether coconut oil, containing C12:0 and C14:0 as main fatty acids, aggravates pressure overload-induced cardiomyopathy induced by transverse aortic constriction (TAC) in C57BL/6 mice. Mortality rate after TAC was higher ( p coconut oil diet-fed mice than in standard chow-fed mice (hazard ratio 2.32, 95% confidence interval 1.16 to 4.64) during eight weeks of follow-up. The effects of coconut oil on cardiac remodeling occurred in the absence of weight gain and of systemic insulin resistance. Wet lung weight was 1.76-fold ( p coconut oil mice than in standard chow mice. Myocardial capillary density ( p coconut oil mice than in standard chow mice. Myocardial glucose uptake was 1.86-fold ( p coconut oil mice and was accompanied by higher myocardial pyruvate dehydrogenase levels and higher acetyl-CoA carboxylase levels. The coconut oil diet increased oxidative stress. Myocardial triglycerides and free fatty acids were lower ( p coconut oil mice. In conclusion, coconut oil aggravates pressure overload-induced cardiomyopathy.

Label-free in situ imaging of oil body dynamics and chemistry in germination.

Science.gov (United States)

Waschatko, Gustav; Billecke, Nils; Schwendy, Sascha; Jaurich, Henriette; Bonn, Mischa; Vilgis, Thomas A; Parekh, Sapun H

2016-10-01

Plant oleosomes are uniquely emulsified lipid reservoirs that serve as the primary energy source during seed germination. These oil bodies undergo significant changes regarding their size, composition and structure during normal seedling development; however, a detailed characterization of these oil body dynamics, which critically affect oil body extractability and nutritional value, has remained challenging because of a limited ability to monitor oil body location and composition during germination in situ Here, we demonstrate via in situ, label-free imaging that oil bodies are highly dynamic intracellular organelles that are morphologically and biochemically remodelled extensively during germination. Label-free, coherent Raman microscopy (CRM) combined with bulk biochemical measurements revealed the temporal and spatial regulation of oil bodies in native soya bean cotyledons during the first eight days of germination. Oil bodies undergo a cycle of growth and shrinkage that is paralleled by lipid and protein compositional changes. Specifically, the total protein concentration associated with oil bodies increases in the first phase of germination and subsequently decreases. Lipids contained within the oil bodies change in saturation and chain length during germination. Our results show that CRM is a well-suited platform to monitor in situ lipid dynamics and local chemistry and that oil bodies are actively remodelled during germination. This underscores the dynamic role of lipid reservoirs in plant development. © 2016 The Authors.

Measurement of molecular diffusion coefficients of carbon dioxide and methane in heavy oil

Energy Technology Data Exchange (ETDEWEB)

Gu, Y.; Tharanivasan, A.K.; Yang, C. [Regina Univ., SK (Canada)

2004-07-01

Vapour extraction (VAPEX) is a solvent-based thermal recovery process which is considered to be a viable process for recovering heavy oil. In order to develop a solvent-based enhanced oil recovery (EOR) operation, it is necessary to know the rate and extent of oil mobilization by the solvent. The molecular diffusion coefficient of solvent gas in heavy oil must be known. In this study, the pressure decay method was used to measure the molecular diffusivity of a gas solvent in heavy oil by monitoring the decaying pressure. The pressure decay method is a non-intrusive method in which physical contact is made between the gas solvent and the heavy oil. The pressure versus time data are measured until the heavy oil reaches complete saturation. The diffusion coefficient can be determined from the measured data and a mathematical model. In this study, the molecular diffusion coefficients of carbon dioxide-heavy oil and methane-heavy oil systems were measured and compared. The experiments were performed in closed high-pressure cells at constant reservoir temperature. An analytical solution was also obtained to predict the pressure in the gas phase and for the boundary conditions at the solvent-heavy oil interface for each solvent. Solvent diffusivity was determined by finding the best match of the numerically predicted and experimentally measured pressures.

The Study of Oils Consumption Pattern and Its Related Factors in east Tehran

Directory of Open Access Journals (Sweden)

Farhad Jafari

2013-09-01

Full Text Available Background & Objective: Inappropriate use of fat in diets is a significant risk factor that can cause cardiovascular diseases, morbidity, and mortality in the world. This study was designed to determine the fat consumption pattern in east Tehran habitants. Materials & Methods: In this cross sectional study 500 east Tehran habitants were evaluated. Data was collected by a questionnaire designed by the authors of the present study. The validity and reliability of the questionnaire was confirmed in a pilot study. The Data was analyzed with SPSS software. Results: The average of family members was 3.9±1.4. The highest amount ofoil consumed was that of solid candy oil, while The lowest was animal oil. For cooking, 36.8% and 31% of samples were using liquid oil and solid candy oil, respectively. For fraying 33.8%, 20%, 32.4% of samples were using liquid oil, solid candy oil and frying oil, respectively. a relationship was found between higher educational level and mothers working out of the house and higher consumption of liquid oil, fraying oil and olive oil (p<0.001. High age, housekeeper mothers and higher family span were associated with the higher consumption of solid oils, butter and ghee (p<0.02. Conclusion: This study revealed that the significant portion of daily oil consumption of Tehran habitants consist of solid oils. It seems to be necessary to organize proper training programs to increase social awareness about the hazards of solid saturated fats.

Geophysics comes of age in oil sands development

Energy Technology Data Exchange (ETDEWEB)

Bauman, P. [WorleyParsons Komex, Calgary, AB (Canada); Birch, R.; Parker, D.; Andrews, B. [Calgary Univ., AB (Canada). Dept. of Geology and Geophysics

2008-07-01

This paper discussed geophysical techniques developed for oil sands exploration and production applications in Alberta's oil sands region. Geophysical methods are playing an important role in mine planning, tailings containment, water supply, and land reclamation activities. Geophysics techniques are used to estimate the volume of muskeg that needs to be stripped and stored for future reclamation activities as well as to site muskeg piles and delineate the thickness of clay Clearwater formations overlying Cretaceous oil-bearing sands. 2-D electrical resistivity mapping is used to map river-connected deep bedrock Pleistocene paleovalleys in the region. Geophysical studies are also used to investigate the interiors of dikes and berms as well as to monitor salt migration within tailings piles. Sonic and density logs are used to create synthetic seismograms for mapping the Devonian surface in the region. The new applications included the calculation of bitumen saturation from surface sands and shales; muskeg thickness mapping; and non-intrusive monitoring of leachate plumes. Geophysical techniques included 2-D electrical resistivity imaging; transient electromagnetic (EM) technologies; ground penetrating radar; and high-resolution seismic reflections. Polarization, surface nuclear magnetic resonance and push-probe sensing techniques were also discussed. Techniques were discussed in relation to Alberta's Athabasca oil sands deposits. 4 refs.

Quantitative monitoring of gas flooding in oil-bearing reservoirs using a pulsed neutron tool

International Nuclear Information System (INIS)

Ruhovets, N.; Wyatt, D.F. Jr.

1991-01-01

This paper reports on quantitative monitoring of gas flooding in oil bearing reservoirs which is unique in that saturations of three fluids (gas, oil and water) in the effective pore space have to be determined, while in most other applications saturation behind casing is determined only for two fluids: hydrocarbons and water. A new method has been developed to monitor gas flooding of oil reservoirs. The method is based on computing two porosities: true effective (base) porosity determined before gas flooding, and apparent effective (monitor) porosity determined after gas flooding. The base porosity is determined from open and/or cased hole porosity logs run before the flooding. When open hole logs are available, the cased hole porosity logs are calibrated against open hole log. The monitor porosity is determined from one of the cased hole porosity logs, such as a neutron log or count rate ratio curve from a pulsed neutron log run after the gas flooding. The base and monitor porosities provide determination of the hydrogen index of the reservoir fluid after the flooding. This hydrogen index is then used to determine saturation of the flood agent after flooding. Water saturation after flooding can be determined from the equation which relates neutron total cross section (Σm) to volumetric constituent cross sections, using Σm values from a monitor run (after flooding)

Characterising Dynamic Instability in High Water-Cut Oil-Water Flows Using High-Resolution Microwave Sensor Signals

Science.gov (United States)

Liu, Weixin; Jin, Ningde; Han, Yunfeng; Ma, Jing

2018-06-01

In the present study, multi-scale entropy algorithm was used to characterise the complex flow phenomena of turbulent droplets in high water-cut oil-water two-phase flow. First, we compared multi-scale weighted permutation entropy (MWPE), multi-scale approximate entropy (MAE), multi-scale sample entropy (MSE) and multi-scale complexity measure (MCM) for typical nonlinear systems. The results show that MWPE presents satisfied variability with scale and anti-noise ability. Accordingly, we conducted an experiment of vertical upward oil-water two-phase flow with high water-cut and collected the signals of a high-resolution microwave resonant sensor, based on which two indexes, the entropy rate and mean value of MWPE, were extracted. Besides, the effects of total flow rate and water-cut on these two indexes were analysed. Our researches show that MWPE is an effective method to uncover the dynamic instability of oil-water two-phase flow with high water-cut.

CGC/saturation approach for soft interactions at high energy: long range rapidity correlations

Energy Technology Data Exchange (ETDEWEB)

Gotsman, E.; Maor, U. [Tel Aviv University, Department of Particle Physics, School of Physics and Astronomy, Raymond and Beverly Sackler Faculty of Exact Science, Tel Aviv (Israel); Levin, E. [Tel Aviv University, Department of Particle Physics, School of Physics and Astronomy, Raymond and Beverly Sackler Faculty of Exact Science, Tel Aviv (Israel); Universidad Tecnica Federico Santa Maria and Centro Cientifico- Tecnologico de Valparaiso, Departemento de Fisica, Valparaiso (Chile)

2015-11-15

In this paper we continue our program to construct a model for high energy soft interactions that is based on the CGC/saturation approach. The main result of this paper is that we have discovered a mechanism that leads to large long range rapidity correlations and results in large values of the correlation function R(y{sub 1}, y{sub 2}) ≥ 1, which is independent of y{sub 1} and y{sub 2}. Such a behavior of the correlation function provides strong support for the idea that at high energies the system of partons that is produced is not only dense but also has strong attractive forces acting between the partons. (orig.)

Combination of Sardine and Shark Oil High Content of Omega-3 and Squalene

Directory of Open Access Journals (Sweden)

Muhamad Musbah

2017-05-01

Full Text Available Sardine oil contain high concentration of  EPA but low of  DHA while shark is reverse. Shark oil  high contain of DHA and squalene but low EPA. This research aim to fortify the quality of  fish oil withomega-3 and squalen and improve the quality of fish oil. The combination of fish oil (sardine:shark 1: 1, 1: 2, 1: 3, 1: 4, 2: 1, 3: 1 and 4:1 showed significant results on peroxide, anisidine, and total oxidation value, however free fatty acids analysis did not show the influence to the content value.  The best oxidation parameters value werefound (sardine: shark (1:4 with peroxide was 5.44±0.06 mEq/kg, anisidine was 8.3±0.72 mEq/kg and total oxidation was 19.27±0.7mEq/kg. Fatty acids profile between  sardines and shark oil containedvarious SFA, MUFA and PUFA. Sardine oil which was added more to combination ratio will increase omega-3. Sample 1:4 had 43.16% squalene.

Oil recovery from naturally fractured reservoirs by steam injection methods. Final report

Energy Technology Data Exchange (ETDEWEB)

Reis, J.C.; Miller, M.A.

1995-05-01

Oil recovery by steam injection is a proven, successful technology for nonfractured reservoirs, but has received only limited study for fractured reservoirs. Preliminary studies suggest recovery efficiencies in fractured reservoirs may be increased by as much as 50% with the application of steam relative to that of low temperature processes. The key mechanisms enhancing oil production at high temperature are the differential thermal expansion between oil and the pore volume, and the generation of gases within matrix blocks. Other mechanisms may also contribute to increased production. These mechanisms are relatively independent of oil gravity, making steam injection into naturally fractured reservoirs equally attractive to light and heavy oil deposits. The objectives of this research program are to quantify the amount of oil expelled by these recovery mechanisms and to develop a numerical model for predicting oil recovery in naturally fractured reservoirs during steam injection. The experimental study consists of constructing and operating several apparatuses to isolate each of these mechanisms. The first measures thermal expansion and capillary imbibition rates at relatively low temperature, but for various lithologies and matrix block shapes. The second apparatus measures the same parameters, but at high temperatures and for only one shape. A third experimental apparatus measures the maximum gas saturations that could build up within a matrix block. A fourth apparatus measures thermal conductivity and diffusivity of porous media. The numerical study consists of developing transfer functions for oil expulsion from matrix blocks to fractures at high temperatures and incorporating them, along with the energy equation, into a dual porosity thermal reservoir simulator. This simulator can be utilized to make predictions for steam injection processes in naturally-fractured reservoirs. Analytical models for capillary imbibition have also been developed.

Application of large computers for predicting the oil field production

Energy Technology Data Exchange (ETDEWEB)

Philipp, W; Gunkel, W; Marsal, D

1971-10-01

The flank injection drive plays a dominant role in the exploitation of the BEB-oil fields. Therefore, 2-phase flow computer models were built up, adapted to a predominance of a single flow direction and combining a high accuracy of prediction with a low job time. Any case study starts with the partitioning of the reservoir into blocks. Then the statistics of the time-independent reservoir properties are analyzed by means of an IBM 360/25 unit. Using these results and the past production of oil, water and gas, a Fortran-program running on a CDC-3300 computer yields oil recoveries and the ratios of the relative permeabilities as a function of the local oil saturation for all blocks penetrated by mobile water. In order to assign kDwU/KDoU-functions to blocks not yet reached by the advancing water-front, correlation analysis is used to relate reservoir properties to kDwU/KDoU-functions. All these results are used as input into a CDC-660 Fortran program, allowing short-, medium-, and long-term forecasts as well as the handling of special problems.

Supercritical fluid chromatography and high temperature liquid chromatography for the group-type separation of diesel fuels and heavy gas oils

Energy Technology Data Exchange (ETDEWEB)

Paproski, R.E.

2008-07-01

This thesis investigated the use of unconventional extraction columns for separating diesel fuels by supercritical fluid chromatography (SFC) and for separating heavy gas oils by high temperature normal phase high performance liquid chromatography (HPLC). The purpose was to improve group-type resolution of the fuels, although these methods are also commonly used to determine the proportion of saturates, mono-, di-, tri-, and polyaromatic hydrocarbons. Higher mobile phase flow rates and unconventional column dimensions were also studied to obtain faster analysis times with both SFC and HPLC. The highest group-type resolutions with SFC were obtained by serially coupling bare titania and bare silica columns. Short packed columns and monolithic silica columns were compared at high carbon dioxide flow rates for reducing SFC analysis time, with shortpacked columns achieving 7-fold lower separation times while maintaining significant resolution. Three diesel samples had better resolution and analysis time. A thermally stable bare zircoma column for normal phase HPLC was studied at temperatures up to 200 degrees C. An increase in temperature resulted in lower retention of twenty five aromatic model compounds. Considerable improvements in peak shape, efficiency, group-type selectivity, and column re-equilibration times were obtained at elevated temperatures. At temperatures over 100 degrees C, indole and carbazole thermally decomposed in a hexane/dichloromethane mobile phase. The first order decomposition of carbazole was studied in further detail. A high resolution method was developed using titania and silica columns with valve-switching and dual gradients to separate 3 heavy gas oils. Separation was achieved in only 3 minutes using a fast analysis time method in a titania column at high flow rates.

Depression, daily stressors and inflammatory responses to high-fat meals: when stress overrides healthier food choices.

Science.gov (United States)

Kiecolt-Glaser, J K; Fagundes, C P; Andridge, R; Peng, J; Malarkey, W B; Habash, D; Belury, M A

2017-03-01

Depression, stress and diet can all alter inflammation. This double-blind, randomized crossover study addressed the impact of daily stressors and a history of major depressive disorder (MDD) on inflammatory responses to high-fat meals. During two separate 9.5 h admissions, 58 healthy women (38 breast cancer survivors and 20 demographically similar controls), mean age 53.1 years, received either a high saturated fat meal or a high oleic sunflower oil meal. The Daily Inventory of Stressful Events assessed prior day stressors and the Structured Clinical Interview for DSM-IV evaluated MDD. As expected, for a woman with no prior day stressors, C-reactive protein (CRP), serum amyloid A (SAA), intercellular adhesion molecule-1 (sICAM-1) and vascular cell adhesion molecule-1 (sVCAM-1) were higher following the saturated fat meal than the high oleic sunflower oil meal after controlling for pre-meal measures, age, trunk fat and physical activity. But if a woman had prior day stressors, these meal-related differences disappeared-because the stressors heightened CRP, SAA, sICAM-1 and sVCAM-1 responses to the sunflower oil meal, making it look more like the responses to the saturated fat meal. In addition, women with an MDD history had higher post-meal blood pressure responses than those without a similar history. These data show how recent stressors and an MDD history can reverberate through metabolic alterations, promoting inflammatory and atherogenic responses.

High freight rates hinder oil markets' return to equilibrium

International Nuclear Information System (INIS)

Anon

2005-01-01

Hurricane damage to refineries in the US has created shortages of refined products there, boosting imports and sending freight rates across the Atlantic to record levels. The situation was made worse for a time by a strike at France's main oil terminals in the Mediterranean, which prevented some oil tankers from being rapidly redeployed to routes across the Atlantic. Worldscale (WS) rates for routes from the UK and Europe to the US Atlantic and Gulf Coasts rose well above WS500 for clean tonnage during October. High rates were nevertheless not simply confined to product tankers crossing the Atlantic. Rates for crude tankers to the US have also risen, and tightness has begun to appear in some other markets as well. The net result has been to slow down the movement of oil from regions of surplus to those of scarcity, depressing prices in the former and keeping them at high levels in the latter. Atlantic tanker markets look like remaining tight for the rest of the year and perhaps beyond. (author)

Estimation of Oil Production Rates in Reservoirs Exposed to Focused Vibrational Energy

KAUST Repository

Jeong, Chanseok

2014-01-01

Elastic wave-based enhanced oil recovery (EOR) is being investigated as a possible EOR method, since strong wave motions within an oil reservoir - induced by earthquakes or artificially generated vibrations - have been reported to improve the production rate of remaining oil from existing oil fields. To date, there are few theoretical studies on estimating how much bypassed oil within an oil reservoir could be mobilized by such vibrational stimulation. To fill this gap, this paper presents a numerical method to estimate the extent to which the bypassed oil is mobilized from low to high permeability reservoir areas, within a heterogeneous reservoir, via wave-induced cross-flow oscillation at the interface between the two reservoir permeability areas. This work uses the finite element method to numerically obtain the pore fluid wave motion within a one-dimensional fluid-saturated porous permeable elastic solid medium embedded in a non-permeable elastic semi-infinite solid. To estimate the net volume of mobilized oil from the low to the high permeability area, a fluid flow hysteresis hypothesis is adopted to describe the behavior at the interface between the two areas. Accordingly, the fluid that is moving from the low to the high permeability areas is assumed to transport a larger volume of oil than the fluid moving in the opposite direction. The numerical experiments were conducted by using a prototype heterogeneous oil reservoir model, subjected to ground surface dynamic loading operating at low frequencies (1 to 50 Hz). The numerical results show that a sizeable amount of oil could be mobilized via the elastic wave stimulation. It is observed that certain wave frequencies are more effective than others in mobilizing the remaining oil. We remark that these amplification frequencies depend on the formation’s elastic properties. This numerical work shows that the wave-based mobilization of the bypassed oil in a heterogeneous oil reservoir is feasible, especially

Eco-Friendly Superwetting Material for Highly Effective Separations of Oil/Water Mixtures and Oil-in-Water Emulsions.

Science.gov (United States)

Wang, Chih-Feng; Yang, Sheng-Yi; Kuo, Shiao-Wei

2017-02-20

Because the treatment of oily wastewater, generated from many industrial processes, has become an increasing environmental concern, the search continues for simple, inexpensive, eco-friendly, and readily scalable processes for fabricating novel materials capable of effective oil/water separation. In this study we prepared an eco-friendly superhydrophilic and underwater superoleophobic polyvinylpyrrolidone (PVP)-modified cotton that mediated extremely efficient separations of mixtures of oil/water and oil/corrosive solutions. This PVP-modified cotton exhibited excellent antifouling properties and could be used to separate oil/water mixtures continuously for up to 20 h. Moreover, the compressed PVP-modified cotton could separate both surfactant-free and -stabilized oil-in-water emulsions with fluxes of up to 23,500 L m -2 h -1 bar -1 -a level one to two orders of magnitude higher than that possible when using traditional ultrafiltration membranes having similar rejection properties. The high performance of our PVP-modified cotton and its green, low-energy, cost-effective preparation suggest its great potential for practical applications.

Problems in waterflooding fields containing paraffinic crude oils

Energy Technology Data Exchange (ETDEWEB)

Kovalev, A G; Lyutin, L V; Perevalov, V G

1968-11-01

When Caspian seawater is injected into the Uzen field reservoir, the temperature of the reservoir oil can be lowered 10/sup 0/ to 20/sup 0/C below initial reservoir temperature. Because Uzen crude oil is saturated with paraffin, the cold injection water can deposit paraffin in the formation and reduce oil recovery. In a related study, it was shown that the lower temperature should not adversely affect capillary and wettability behavior of the crude oil in the reservoir. Oil recovery was found to be essentially independent of water composition. However, fresh water is easier to handle in injection systems than brines. Several studies have shown that oil recovery from Uzen field should be increased by use of hot injection water. Various methods of heating the water are discussed. To reduce corrosivity and scaling of hot brine, sodium hexametaphosphate is added in concentrations of 2 to 15 mg/liter. It is concluded that it would be practical to use hot injection water in this field.

Numerical Simulation Study on Steam-Assisted Gravity Drainage Performance in a Heavy Oil Reservoir with a Bottom Water Zone

Directory of Open Access Journals (Sweden)

Jun Ni

2017-12-01

Full Text Available In the Pikes Peak oil field near Lloydminster, Canada, a significant amount of heavy oil reserves is located in reservoirs with a bottom water zone. The properties of the bottom water zone and the operation parameters significantly affect oil production performance via the steam-assisted gravity drainage (SAGD process. Thus, in order to develop this type of heavy oil resource, a full understanding of the effects of these properties is necessary. In this study, the numerical simulation approach was applied to study the effects of properties in the bottom water zone in the SAGD process, such as the initial gas oil ratio, the thickness of the reservoir, and oil saturation of the bottom water zone. In addition, some operation parameters were studied including the injection pressure, the SAGD well pair location, and five different well patterns: (1 two corner wells, (2 triple wells, (3 downhole water sink well, (4 vertical injectors with a horizontal producer, and (5 fishbone well. The numerical simulation results suggest that the properties of the bottom water zone affect production performance extremely. First, both positive and negative effects were observed when solution gas exists in the heavy oil. Second, a logarithmical relationship was investigated between the bottom water production ratio and the thickness of the bottom water zone. Third, a non-linear relation was obtained between the oil recovery factor and oil saturation in the bottom water zone, and a peak oil recovery was achieved at the oil saturation rate of 30% in the bottom water zone. Furthermore, the operation parameters affected the heavy oil production performance. Comparison of the well patterns showed that the two corner wells and the triple wells patterns obtained the highest oil recovery factors of 74.71% and 77.19%, respectively, which are almost twice the oil recovery factors gained in the conventional SAGD process (47.84%. This indicates that the optimized SAGD process

Methane accumulation and forming high saturations of methane hydrate in sandy sediments

Energy Technology Data Exchange (ETDEWEB)

Uchida, T.; Waseda, A. [JAPEX Research Center, Chiba (Japan); Fujii, T. [Japan Oil, Gas and Metals National Corp., Chiba (Japan). Upstream Technology Unit

2008-07-01

Methane supplies for marine gas hydrates are commonly attributed to the microbial conversion of organic materials. This study hypothesized that methane supplies were related to pore water flow behaviours and microscopic migration in intergranular pore systems. Sedimentology and geochemistry analyses were performed on sandy core samples taken from the Nankai trough and the Mallik gas hydrate test site in the Mackenzie Delta. The aim of the study was to determine the influence of geologic and sedimentolic controls on the formation and preservation of natural gas hydrates. Grain size distribution curves indicated that gas hydrate saturations of up to 80 per cent in pore volume occurred throughout the hydrate-dominant sand layers in the Nankai trough and Mallik areas. Water permeability measurements showed that the highly gas hydrate-saturated sands have a permeability of a few millidarcies. Pore-space gas hydrates occurred primarily in fine and medium-grained sands. Core temperature depression, core observations, and laboratory analyses of the hydrates confirmed the pore-spaces as intergranular pore fillings. Results of the study suggested that concentrations of gas hydrates may require a pore space large enough to occur within a host sediments, and that the distribution of porous and coarser-grained sandy sediments is an important factor in controlling the occurrence of gas hydrates. 11 refs., 4 figs.

Possibility of removing condensate and scattered oil from gas-condensate field during bed flooding

Energy Technology Data Exchange (ETDEWEB)

Belkina, N.A.; Yagubov, M.S.

1984-01-01

The problem is set of evaluating the possible removal from the bed of scattered oil and condensate during flooding of the bed. For this purpose, an experimental study was made of the displacement by water from the porous medium of the oil and condensate saturating it. The obtained experimental results permit evaluation of the possible removal from the gas-condensate bed of scattered oil and condensate during flooding of the bed.

Avocado oil extraction processes: method for cold-pressed high-quality edible oil production versus traditional production

OpenAIRE

Giacomo Costagli; Matteo Betti

2015-01-01

Nowadays the avocado fruit (Persea americana Mill.) is widely regarded as an important fruit for its nutritional values, as it is rich in vital human nutrients. The avocado fruit is mainly sold fresh on the market, which however trades also a relevant quantity of second-grade fruits with a relatively high oil content. Traditionally, this oil is extracted from dried fruits by means of organic solvents, but a mechanical method is also used in general in locations where drying systems and/or sol...

In vitro mutagenicity assay (Ames test and phytochemical characterization of seeds oil of Helianthus annuus Linné (sunflower

Directory of Open Access Journals (Sweden)

Nelma de Mello Silva Oliveira

Full Text Available The objective of this research was to investigate the genotoxic potential of the oil of H. annuus L. (sunflower seeds via the Ames test as well as its oxidative properties and lipid composition. The pre-incubation method, system metabolic activation (S9 fraction and five S. typhimurium strains (TA97, TA98, TA100, TA1535 and TA102 were employed for the Ames test. The oxidative stability and fatty acid composition were analyzed by standard methods and gas chromatography. A revertant analysis showed no significant differences between the treatment doses (10–200 μl/plate and the negative controls, regardless of S9+ and S9−, and included all of the S. typhimurium strains. Chromatographic analysis showed high levels of polyunsaturated fatty acids, followed by monounsaturated, saturated and total trans-isomers. Among the polyunsaturated, monounsaturated and saturated fatty acids, linoleic, oleic and palmitic acids predominated. The results suggest that the sunflower oil is not genotoxic as indicated by frameshift mutations and base pair substitutions regardless of the treatment dose, but shows dose-dependent toxicity. The oxidative properties of the sunflower oil were consistent with the requirements of national and international standards. However, its composition could also indicate phytotherapeutic properties. Keywords: Helianthus annuus L., Sunflower oil, Genetic toxicity, Gas chromatography

High-sensitivity HLA typing by Saturated Tiling Capture Sequencing (STC-Seq).

Science.gov (United States)

Jiao, Yang; Li, Ran; Wu, Chao; Ding, Yibin; Liu, Yanning; Jia, Danmei; Wang, Lifeng; Xu, Xiang; Zhu, Jing; Zheng, Min; Jia, Junling

2018-01-15

Highly polymorphic human leukocyte antigen (HLA) genes are responsible for fine-tuning the adaptive immune system. High-resolution HLA typing is important for the treatment of autoimmune and infectious diseases. Additionally, it is routinely performed for identifying matched donors in transplantation medicine. Although many HLA typing approaches have been developed, the complexity, low-efficiency and high-cost of current HLA-typing assays limit their application in population-based high-throughput HLA typing for donors, which is required for creating large-scale databases for transplantation and precision medicine. Here, we present a cost-efficient Saturated Tiling Capture Sequencing (STC-Seq) approach to capturing 14 HLA class I and II genes. The highly efficient capture (an approximately 23,000-fold enrichment) of these genes allows for simplified allele calling. Tests on five genes (HLA-A/B/C/DRB1/DQB1) from 31 human samples and 351 datasets using STC-Seq showed results that were 98% consistent with the known two sets of digitals (field1 and field2) genotypes. Additionally, STC can capture genomic DNA fragments longer than 3 kb from HLA loci, making the library compatible with the third-generation sequencing. STC-Seq is a highly accurate and cost-efficient method for HLA typing which can be used to facilitate the establishment of population-based HLA databases for the precision and transplantation medicine.

Gluon saturation in a saturated environment

International Nuclear Information System (INIS)

Kopeliovich, B. Z.; Potashnikova, I. K.; Schmidt, Ivan

2011-01-01

A bootstrap equation for self-quenched gluon shadowing leads to a reduced magnitude of broadening for partons propagating through a nucleus. Saturation of small-x gluons in a nucleus, which has the form of transverse momentum broadening of projectile gluons in pA collisions in the nuclear rest frame, leads to a modification of the parton distribution functions in the beam compared with pp collisions. In nucleus-nucleus collisions all participating nucleons acquire enhanced gluon density at small x, which boosts further the saturation scale. Solution of the reciprocity equations for central collisions of two heavy nuclei demonstrate a significant, up to several times, enhancement of Q sA 2 , in AA compared with pA collisions.

Synthesis of FeSiBPNbCu nanocrystalline soft-magnetic alloys with high saturation magnetization

Energy Technology Data Exchange (ETDEWEB)

Li, Zongzhen [China Iron and Steel Research Institute Group, Advanced Technology and Materials Co., Ltd., Beijing 100081 (China); Wang, Anding; Chang, Chuntao [Key Laboratory of Magnetic Materials and Devices, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, 519 Zhuangshi Road, Zhenhai District, Ningbo, Zhejiang 315201 (China); Wang, Yanguo [Institute of Physics, Chinese Academy of Sciences, PO Box 603, Beijing 100080 (China); Dong, Bangshao [China Iron and Steel Research Institute Group, Advanced Technology and Materials Co., Ltd., Beijing 100081 (China); Zhou, Shaoxiong, E-mail: sxzhou@atmcn.com [China Iron and Steel Research Institute Group, Advanced Technology and Materials Co., Ltd., Beijing 100081 (China)

2014-10-25

Highlights: • Thermal stability of the FeSiBPNbCu alloys is strongly dependent on the Fe content. • The FeSiBPNbCu alloys with high Fe content exhibit good soft magnetic properties. • The coexistence of Cu, P and Nb leads to the excellent soft magnetic properties. - Abstract: A series of [Fe{sub 0.76+x}(Si{sub 0.4}B{sub 0.4}P{sub 0.2}){sub 0.24−x}]{sub 98.25}Nb{sub 1}Cu{sub 0.75} (x = 0–0.08) nanocrystalline soft-magnetic alloys with high saturation magnetization were synthesized by adjusting Fe content and improving the crystallization behavior, soft-magnetic properties and microstructure. It is found that the temperature interval between the two crystallization peaks is significantly enlarged from 50 to 180 °C when the Fe content of the alloys increases from x = 0 to x = 0.08, which greatly expands the optimum annealing temperature range. The alloys with higher Fe content are prone to form more uniform nanocomposite microstructure with better thermal stability and soft magnetic properties. The Fe-rich FeSiBPNbCu nanocrystalline alloys with x = 0.08 exhibit excellent soft-magnetic properties, including the high saturation magnetic flux density of up to 1.74 T, low coercivity of about 3.3 A/m and high effective permeability of more than 2.2 × 10{sup 4} at 1 kHz under a field of 1 A/m. The combination of excellent soft-magnetic properties, low cost and good productivity makes the FeSiBPNbCu alloys to be a kind of promising soft-magnetic materials for electrical and electronic industry applications.

A combination of streamtube and geostatical simulation methodologies for the study of large oil reservoirs

Energy Technology Data Exchange (ETDEWEB)

Chakravarty, A.; Emanuel, A.S.; Bernath, J.A. [Chevron Petroleum Technology Company, LaHabra, CA (United States)

1997-08-01

The application of streamtube models for reservoir simulation has an extensive history in the oil industry. Although these models are strictly applicable only to fields under voidage balance, they have proved to be useful in a large number of fields provided that there is no solution gas evolution and production. These models combine the benefit of very fast computational time with the practical ability to model a large reservoir over the course of its history. These models do not, however, directly incorporate the detailed geological information that recent experience has taught is important. This paper presents a technique for mapping the saturation information contained in a history matched streamtube model onto a detailed geostatistically derived finite difference grid. With this technique, the saturation information in a streamtube model, data that is actually statistical in nature, can be identified with actual physical locations in a field and a picture of the remaining oil saturation can be determined. Alternatively, the streamtube model can be used to simulate the early development history of a field and the saturation data then used to initialize detailed late time finite difference models. The proposed method is presented through an example application to the Ninian reservoir. This reservoir, located in the North Sea (UK), is a heterogeneous sandstone characterized by a line drive waterflood, with about 160 wells, and a 16 year history. The reservoir was satisfactorily history matched and mapped for remaining oil saturation. A comparison to 3-D seismic survey and recently drilled wells have provided preliminary verification.

Interger multiplication with overflow detection or saturation

Energy Technology Data Exchange (ETDEWEB)

Schulte, M.J.; Balzola, P.I.; Akkas, A.; Brocato, R.W.

2000-01-11

High-speed multiplication is frequently used in general-purpose and application-specific computer systems. These systems often support integer multiplication, where two n-bit integers are multiplied to produce a 2n-bit product. To prevent growth in word length, processors typically return the n least significant bits of the product and a flag that indicates whether or not overflow has occurred. Alternatively, some processors saturate results that overflow to the most positive or most negative representable number. This paper presents efficient methods for performing unsigned or two's complement integer multiplication with overflow detection or saturation. These methods have significantly less area and delay than conventional methods for integer multiplication with overflow detection and saturation.

Experimental and numerical study on thermal conductivity of partially saturated unconsolidated sands

Science.gov (United States)

Lee, Youngmin; Keehm, Youngseuk; Kim, Seong-Kyun; Shin, Sang Ho

2016-04-01

A class of problems in heat flow applications requires an understanding of how water saturation affects thermal conductivity in the shallow subsurface. We conducted a series of experiments using a sand box to evaluate thermal conductivity (TC) of partially saturated unconsolidated sands under varying water saturation (Sw). We first saturated sands fully with water and varied water saturation by drainage through the bottom of the sand box. Five water-content sensors were integrated vertically into the sand box to monitor water saturation changes and a needle probe was embedded to measure thermal conductivity of partially saturated sands. The experimental result showed that thermal conductivity decreases from 2.5 W/mK for fully saturated sands to 0.7 W/mK when water saturation is 5%. We found that the decreasing trend is quite non-linear: highly sensitive at very high and low water saturations. However, the boundary effects on the top and the bottom of the sand box seemed to be responsible for this high nonlinearity. We also found that the determination of water saturation is quite important: the saturation by averaging values from all five sensors and that from the sensor at the center position, showed quite different trends in the TC-Sw domain. In parallel, we conducted a pore-scale numerical modeling, which consists of the steady-state two-phase Lattice-Boltzmann simulator and FEM thermal conduction simulator on digital pore geometry of sand aggregation. The simulation results showed a monotonous decreasing trend, and are reasonably well matched with experimental data when using average water saturations. We concluded that thermal conductivity would decrease smoothly as water saturation decreases if we can exclude boundary effects. However, in dynamic conditions, i.e. imbibition or drainage, the thermal conductivity might show hysteresis, which can be investigated with pore-scale numerical modeling with unsteady-state two-phase flow simulators in our future work.

Elastoplastic model for unsaturated, quasi-saturated and fully saturated fine soils

Directory of Open Access Journals (Sweden)

Lai Ba Tien

2016-01-01

Full Text Available In unsaturated soils, the gaseous phase is commonly assumed to be continuous. This assumption is no more valid at high saturation ratio. In that case, air bubbles and pockets can be trapped in the porous network by the liquid phase and the gas phase becomes discontinuous. This trapped air reduces the apparent compressibility of the pore fluid and affect the mechanical behavior of the soil. Although it is trapped in the pores, its dissolution can take place. Dissolved air can migrate through the pore space, either by following the flow of the fluid or by diffusion. In this context, this paper present a hydro mechanical model that separately considers the kinematics and the mechanical behavior of each fluid species (eg liquid water, dissolved air, gaseous air and the solid matrix. This new model was implemented in a C++ code. Some numerical simulations are performed to demonstrate the ability of this model to reproduce a continuous transition of unsaturated to saturated states.

Density and viscosity behavior of a North Sea crude oil, natural gas liquid, and their mixtures

DEFF Research Database (Denmark)

Schmidt, KAG; Cisneros, Sergio; Kvamme, B

2005-01-01

to accurately model the saturation pressures, densities, and viscosities of petroleum systems ranging from natural gases to heavy crude oils. The applicability of this overall modeling technique to reproduce measured bubble points, densities, and viscosities of a North Sea crude oil, a natural gas liquid...

Viscous fingering effects in solvent displacement of heavy oil

Energy Technology Data Exchange (ETDEWEB)

Cuthiell, D. [Suncor Energy, Fort McMurray, AB (Canada); Kissel, G.; Jackson, C.; Frauenfeld, T.W.J.; Fisher, D. [Alberta Research Council, Devon, AB (Canada); Rispler, K. [Saskatchewan Research Council, Saskatoon, SK (Canada)

2004-07-01

Vapour Extraction (VAPEX) is a solvent-based process that is analogous to steam-assisted gravity drainage (SAGD) for the recovery of heavy oil. A cyclic solvent process is preferred for thin reservoirs, particularly primary-depleted reservoirs. In a cyclic steam stimulation process, a solvent is injected into the reservoir for a period of time before oil is produced from the well. Viscous fingering is a phenomena that characterizes several solvent-based processes for the recovery of heavy oil. A combined experimental and simulation study was conducted to characterize viscous fingering under heavy oil recovery conditions (high ratio of oil to solvent viscosity). Four experiments were conducted in heavy oil-saturated sand packs. Three involved injection of a miscible, liquid solvent at the bottom of the sand pack. The heavy oil in these experiments was displaced upwardly. The fourth experiment involved top-down injection of a gaseous solvent. The miscible liquid displacement was dominated by one solvent finger which broke through to a producing well at the other end of the sand pack. Breakthrough times were similar to that at lower viscosity. The fourth experiment showed fingering along with features of a gravity-driven VAPEX process. Key features of the experiment and realistic fingering patterns were numerically simulated using a commercial reservoir simulator. It was emphasized that accurate modelling of dispersion is necessary in matching the observed phenomena. The simulations should include the capillary effects because of their significance for gaseous fingering and the VAPEX processes. 17 refs., 2 tabs., 20 figs.

Economic study of NHR application on high pour point oil field

International Nuclear Information System (INIS)

Zhao Gang; Zhang Zuoyi; Ma Yuanle

1997-01-01

In order to extent the application of NHR (nuclear heating reactor) and cut down the oil production costs, the authors designed different heating disposition by NHR and boiler heating stations in high pour point oil reservoir, total 16.9 km 2 , in Daqing oil field. This work was based on the study of history matching, water flood planning and hot water circulation for the reservoir. The analyzing results show that, the convert heating cost of NHR is a third of boiler's and the net oil production of NHR is 4 times more than the latter. Considering economization and reliability, authors suggest to adopt the scheme of two NHR with one boiler heating station

A high-fat, high-saturated fat diet decreases insulin sensitivity without changing intra-abdominal fat in weight-stable overweight and obese adults.

Science.gov (United States)

von Frankenberg, Anize D; Marina, Anna; Song, Xiaoling; Callahan, Holly S; Kratz, Mario; Utzschneider, Kristina M

2017-02-01

We sought to determine the effects of dietary fat on insulin sensitivity and whether changes in insulin sensitivity were explained by changes in abdominal fat distribution or very low-density lipoprotein (VLDL) fatty acid composition. Overweight/obese adults with normal glucose tolerance consumed a control diet (35 % fat/12 % saturated fat/47 % carbohydrate) for 10 days, followed by a 4-week low-fat diet (LFD, n = 10: 20 % fat/8 % saturated fat/62 % carbohydrate) or high-fat diet (HFD, n = 10: 55 % fat/25 % saturated fat/27 % carbohydrate). All foods and their eucaloric energy content were provided. Insulin sensitivity was measured by labeled hyperinsulinemic-euglycemic clamps, abdominal fat distribution by MRI, and fasting VLDL fatty acids by gas chromatography. The rate of glucose disposal (Rd) during low- and high-dose insulin decreased on the HFD but remained unchanged on the LFD (Rd-low: LFD: 0.12 ± 0.11 vs. HFD: -0.37 ± 0.15 mmol/min, mean ± SE, p vs. HFD: -0.71 ± 0.26 mmol/min, p = 0.08). Hepatic insulin sensitivity did not change. Changes in subcutaneous fat were positively associated with changes in insulin sensitivity on the LFD (r = 0.78, p fat. The LFD led to an increase in VLDL palmitic (16:0), stearic (18:0), and palmitoleic (16:1n7c) acids, while no changes were observed on the HFD. Changes in VLDL n-6 docosapentaenoic acid (22:5n6) were strongly associated with changes in insulin sensitivity on both diets (LFD: r = -0.77; p fat and saturated fat adversely affects insulin sensitivity and thereby might contribute to the development of type 2 diabetes. CLINICALTRIALS. NCT00930371.