WorldWideScience

Sample records for high energy sulphur

  1. Ball-milling synthesis of ZnO@sulphur/carbon nanotubes and Ni(OH)_2@sulphur/carbon nanotubes composites for high-performance lithium-sulphur batteries

    International Nuclear Information System (INIS)

    Gu, Xingxing; Tong, Chuan-jia; Wen, Bo; Liu, Li-min; Lai, Chao; Zhang, Shanqing

    2016-01-01

    Highlights: • Metal oxides or hydroxides coating sulfur-based composite are successfully prepared. • Large-scale synthesis can be realized via the facile wet ball-milling strategy. • Density functional theory (DFT) calculation is applied to calculate adsorption energy. • ZnO exhibits a higher adsorption energy for Li_2S_8 than that Ni(OH)_2. • ZnO@sulphur/carbon nanotubes composite show excellent cycle and discharge performance. - Abstract: Zinc oxide wrapped sulphur/carbon nanotubes (ZnO@S/CNT) and nickel hydroxide wrapped sulphur/carbon nanotubes (Ni(OH)_2@S/CNT) nanocomposites are prepared using a simple, low cost and scalable ball-milling method. As the cathodes in Li-S batteries, the as-prepared ZnO@S/CNT composite illustrates a superior high initial capacity of 1663 mAh g"−"1 at a charge/discharge rate of 160 mA g"−"1, and maintains a reversible capacity at approximately 942 mAh g"−"1 after 70 cycles. While for Ni(OH)_2@S/CNT composites, its initial capacity is also as high as 1331 mAh g"−"1, but a poorer cycling stability is presented. When the charge/discharge current is increased to 1600 mA g"−"1, a high reversible capacity of 698 mAh g"−"1 after 200 cycles still can be obtained for the ZnO@S/CNT composite, far better than that of Ni(OH)_2@S/CNT composites. The better cycling performance and high discharge capacity can be attributed to the strong interactions between ZnO and S_x"2"− species, which is verified by the density functional theory (DFT) calculation result that the ZnO exhibits a higher adsorption energy for Li_2S_8 than the Ni(OH)_2.

  2. Biodesulphurisation of high sulphur coal by heap leaching

    Energy Technology Data Exchange (ETDEWEB)

    J. Cara; M.T. Carballo; A. Moran; D. Bonilla; O. Escolano; F.J. Garcia Frutos [Universidad de Leon, Leon (Spain). Departamento de Ingenieria Quimica

    2005-10-01

    The biodesulphurisation of coal carried out in pile could be an interesting option to clean coal. In view of the good results obtained in biodesulphurisation test column at lab scale on a sample of semianthracite coal that proceed of an industrial plant with a high sulphur content, mainly pyritic sulphur, the feasibility of the process at pilot plant scale was studied. The pile was formed with 6 ton of gravity middlings coal sample with a grain size -12+0.5 mm from S.A. Hullera Vasco-Leonesa industrial plant. The coal has a total sulphur content of 3.78% and a pyritic sulphur content of 2.88%, the rest of sulphur is organic sulphur. The biodesulphurisation process in pilot plant follows three stages: stabilization of the pile, biodesulphurisation and washing. Heap was sampled twice during stabilisation stage, at the end of desulphurisation process and finally once washed. A pyritic sulphur removal of 39% and total sulphur removal of 23% was obtained. To complete the bioleaching process, the treatment of purge of leachate was carried out with the objective to recycling to head of process. The best treatment was a pre-treatment of the leachate until pH 4, and further treatment by reverse osmosis of the clarified water. Comparing this process with conventional precipitation to reach disposal limits, the reagents consumption and sludges were reduced considerably and due to the high quality of permeate it permits to recycle it to head of process. 18 refs., 6 figs., 6 tabs.

  3. Discharging a Li-S battery with ultra-high sulphur content cathode using a redox mediator.

    Science.gov (United States)

    Kim, Kwi Ryong; Lee, Kug-Seung; Ahn, Chi-Yeong; Yu, Seung-Ho; Sung, Yung-Eun

    2016-08-30

    Lithium-sulphur batteries are under intense research due to the high specific capacity and low cost. However, several problems limit their commercialization. One of them is the insulating nature of sulphur, which necessitates a large amount of conductive agent and binder in the cathode, reducing the effective sulphur load as well as the energy density. Here we introduce a redox mediator, cobaltocene, which acts as an electron transfer agent between the conductive surface and the polysulphides in the electrolyte. We confirmed that cobaltocene could effectively convert polysulphides to Li2S using scanning electron microscope, X-ray absorption near-edge structure and in-situ X-ray diffraction studies. This redox mediator enabled excellent electrochemical performance in a cathode with ultra-high sulphur content (80 wt%). It delivered 400 mAh g(-1)cathode capacity after 50 cycles, which is equivalent to 800 mAh g(-1)S in a typical cathode with 50 wt% sulphur. Furthermore, the volumetric capacity was also dramatically improved.

  4. Performance evaluation of high-sulphur coal-fired USC plant integrated with SNOX and CO2 capture sections

    International Nuclear Information System (INIS)

    Cau, Giorgio; Tola, Vittorio; Bassano, Claudia

    2015-01-01

    In recent years coal-fired power plants have increased their role in the global energy scenario thanks to reliability, security of fuel supply and lower cost of fuel and electricity. In this framework global warming issues require a sustainable use of coal and great efforts for greenhouse gases reduction, addressing research and development projects towards more efficient solutions in terms of efficiency and environmental impact. With this aim in this paper a performance assessment of an Ultra Super Critical (USC) steam plant integrated with a CO 2 removal section was carried out. The study is based on simulation models specifically developed through Aspen-Plus and Gate-Cycle software platforms. Performance was assessed referring to typical USC commercial size plants (400–600 MW), fuelled by a mix of a low-sulphur coal and a Sardinian (Sulcis) high-sulphur coal. The USC plant, based on a reheated and regenerative Rankine cycle, is integrated with an SNOX section, with integrated DeNO x and DeSO x processes, and a low temperature CO 2 capture section. The SNOX technology shows several advantages in comparison to conventional de-nitrification and de-sulphuration systems. In particular it is capable to remove both nitrogen and sulphur oxides, requiring less energy absorption compared to traditional FGD systems, allowing a further preheating of the combustion air and without producing process waste. Besides the SNOX releases a commercial product as the sulphuric acid (H 2 SO 4 ) and operational costs are reduced when sulphur content in the coal increases. The CO 2 capture system was based on a chemical absorption process. A conventional system based on an amine (monoethanolamine, MEA) aqueous solution was considered. In order to match high pressure and purity CO 2 transportation requirements, the CO 2 removal section is also integrated with a conditioning and compression section. A performance assessment of the USC plant was carried out varying the high-sulphur coal

  5. Sulphur output from oil sands : dramatically changing Alberta's sulphur balance

    International Nuclear Information System (INIS)

    D'Aquin, G.

    2008-01-01

    This paper discussed sulphur production from Alberta's gas and oil sands industries. While sulfur derived from natural gas production in the province is expected to decline as natural gas reserves diminish, Alberta's oil sands contain high amounts of sulphur. It is not yet known how much sulphur will be produced from the province's oil sands facilities. Alberta had considerable stockpiles of sulphur in the 1970s. By 1980, inventories began to decline. By 1996, output had increased to 7.1 million tonnes. Alberta's sulphur inventory reached 9.7 million tonnes following the collapse of the Soviet Union's government mandated fertilizer industry. In 2006, sulphur supplies in Alberta reached 12 million tonnes. Reduced global output has now lowered sulphur stockpiles. Increases in sulphur prices tend to reduce market demand, and lower prices will not typically change the volume of sulphur produced as a byproduct of oil and gas operations. Bitumen-derived sulphur output is expected to exceed gas-derived sulphur output in the near future. Sulphur from oil sands processing is expected to increase by 5 million tonnes by 2017. Increased sulphur production levels in Alberta will present a significant challenge for all sectors of the hydrocarbon industry. It was concluded that developing a plan for storing, selling or disposing of the sulphur will help to ensure the profitability of oil sands operations

  6. Strange and non-strange baryon and antibaryon production in sulphur-tungsten and sulphur-sulphur interactions at 200 A Gev/c

    Energy Technology Data Exchange (ETDEWEB)

    Holme, A.K.

    1995-11-01

    The author has studied production of strange and multistrange baryons and antibaryons in central sulphur-tungsten, sulphur-sulphur, and lead-lead interactions at relativistic energies. The spectra of strange baryons and antibaryons provide information about the dynamics of hadronic matter under the extreme conditions realised in these collisions. The particle ratios allow the degree and the nature of the flavour equilibrium to be studied, while the transverse mass distributions provide independent information of the temperatures achieved. 143 refs.

  7. Strange and non-strange baryon and antibaryon production in sulphur-tungsten and sulphur-sulphur interactions at 200 A Gev/c

    International Nuclear Information System (INIS)

    Holme, A.K.

    1995-11-01

    The author has studied production of strange and multistrange baryons and antibaryons in central sulphur-tungsten, sulphur-sulphur, and lead-lead interactions at relativistic energies. The spectra of strange baryons and antibaryons provide information about the dynamics of hadronic matter under the extreme conditions realised in these collisions. The particle ratios allow the degree and the nature of the flavour equilibrium to be studied, while the transverse mass distributions provide independent information of the temperatures achieved. 143 refs

  8. Sulphur capture by co-firing sulphur containing fuels with biomass fuels - optimization

    International Nuclear Information System (INIS)

    Nordin, A.

    1992-12-01

    Previous results concerning co-firing of high sulphur fuels with biomass fuels have shown that a significant part of the sulphur can be absorbed in the ash by formation of harmless sulphates. The aim of this work has been to (i) determine the maximum reduction that can be obtained in a bench scaled fluidized bed (5 kW); (ii) determine which operating conditions will give maximum reduction; (iii) point out the importance and applicability of experimental designs and multivariate methods when optimizing combustion processes; (iv) determine if the degree of sulphur capture can be correlated to the degree of slagging, fouling or bed sintering; and (v) determine if further studies are desired. The following are some of the more important results obtained: - By co-firing peat with biomass, a total sulphur retention of 70 % can be obtained. By co-firing coal with energy-grass, the total SO 2 emissions can be reduced by 90 %. - Fuel feeding rate, amount of combustion air and the primary air ratio were the most important operating parameters for the reduction. Bed temperature and oxygen level seem to be the crucial physical parameters. - The NO emissions also decreased by the sulphur reducing measures. The CO emissions were relatively high (130 mg/MJ) compared to large scale facilities due to the small reactor and the small fluctuations in the fuel feeding rate. The SO 2 emissions could however be reduced without any increase in CO emissions. - When the reactor was fired with a grass, the bed sintered at a low temperature ( 2 SO 4 and KCl are formed no sintering problems were observed. (27 refs., 41 figs., 9 tabs., 3 appendices)

  9. Reduced emissions from inexpensive high-sulphur coal briquettes

    International Nuclear Information System (INIS)

    Gammage, R.B.; Wachter, E.A.; Wade, J.; Wilson, D.L.; Haas, J.W.; Ahmad, N.; Siltain, F.; Raza, M.Z.

    1992-01-01

    Airborne emissions were measured during the combustion of Pakistani high-sulphur coal, cold briquetted with lime and clay; comparison was made to emissions from raw coal and traditional fuels burnt in a native, mud-lined Angethi stove. Compared to raw coal, the amended coal gave fourfold reduced emission of respirable-size particles (RSP) and threefold reduced total releases of SO 2 . In domestic cooking, substitution of the amended coal briquettes for traditional fuels will not worsen indoor air quality with respect to CO, SO 2 , NO x , and RSP. The high peak amounts of CO (100--250 ppm), SO 2 (2--5 ppm), and NO x (1--5 ppm) were limited to the early phase of burning. The high thermal value of the coal briquettes together with a simple briquetting technology, make this fuel an attractive energy alternative in countries that are underdeveloped, developing, or experiencing major restructuring

  10. Sulphur recovery and sulphur emissions at Alberta sour gas plants : annual report for 2005

    International Nuclear Information System (INIS)

    2005-01-01

    The sulphur recovery of Alberta's grandfathered sour gas plants is monitored by the Alberta Energy and Utilities Board. This report provides an annual summary of industry performance for sulphur recovery at large acid gas flaring sour gas plants, and sulphur recovery at all acid gas injection sour gas plants. It follows Interim Directive (ID) 2001-3 which stipulates guidelines for sulphur recovery for the province of Alberta. It includes a list of grandfathered and non grandfathered plants in Alberta. Grandfathered sulphur recovery plants that exceed expectations have the option to file a sulphur emission performance credit report and can use the credits to meet some of their sulphur requirement in the future. Acid gas flaring plants face more stringent requirements and cannot earn credits. Several plants have degrandfathered in the past 5 years. Eleven have made upgrades, 4 have been relicensed to meet the requirements for new plants, and 4 have shut down. Forty-one grandfathered plants remain. Sulphur emissions have decreased 39 per cent for grandfathered acid gas flaring plants, and 28 per cent for grandfathered sulphur recovery plants. 10 tabs., 3 figs

  11. Solving the sulphur situation : research assesses viability of burying sulphur

    International Nuclear Information System (INIS)

    Proce, B.

    2006-01-01

    Oil sands mining companies are looking for ways to manage growing levels of sulphur production from the Athabasca region. Infrastructure is not in place to economically transport the sulphur even though there is a global market for it. Sulphur cannot be stockpiled indefinitely as it can react with air to produce sulphur dioxide. Although above-ground sulphur storage has been regulated for more than 30 years, the underground storage of sulphur is still in a research and development phase. Alberta Sulphur Research Ltd. is currently conducting an ongoing experiment in which 100 tonne test blocks have been buried above and below the water table so that surrounding areas could be monitored over a period of years. A series of tests is being conducted to examine changes in pH in water and sulphate levels. A multi-layered engineering casing to contain the sulphur and prevent seepage is also being investigated. Once stored underground, operators also have to consider how the sulphur will be accessed in the future, as it is subject to government royalties. The storage of sulphur may have economic benefits as the product can be sold when prices are high. Most sulphur produced in Alberta is sold as an export product in the United States for use in products such as fertilizer. Shell Canada penetrated the Chinese market in 2001 and has since become one of Canada's largest sulphur exporters. Shell has also introduced a number of products using sulphur, including fertilizers, enhanced asphalt, and concrete. It was concluded that companies must take action now to mitigate future losses and to utilize current markets in order to remain competitive. 3 figs

  12. A new technology aimed at re-establishing a global sulphur supply/demand balance

    International Nuclear Information System (INIS)

    Slavens, A.F.; Jorgensen, C.; Ogg, D.

    2009-01-01

    The world's sulphur supply is mainly determined by involuntary production of elemental sulphur during the processing of oil and gas. As a result, sulphur supply is decoupled from demand, resulting in an imbalance between the two. For almost two decades, sulphur supply has exceeded demand, which has raised significant concerns for oil and gas producers such as where to store all of the excess sulphur, and how to transport a low-value commodity to market in an economically attractive fashion. Black and Veatch is involved in the development of a new technology called sulphur to energy process (STEP TM ) which has the potential to assist in balancing global sulphur supply and demand, as well as affording other benefits such as low-emission energy production. This paper presented the potential merits of the STEP as a means to reestablish a global sulphur supply/demand balance for the world trading market. It explored the other potential benefits that may result from the use of this new technology and compared STEP to other technologies and operating schemes that regulate sulphur supply. It was concluded that STEP has the potential to allow the processor to produce elemental sulphur when demand is high, or to provide safe and ecological disposal when demand is low, with the added benefits of energy recovery from the sulphur combustion process, and sour gas reservoir sweetening over time as sulphur dioxide reacts with hydrogen sulphide present in the reservoir. 13 refs., 3 tabs., 22 figs

  13. High-temperature removal of sulphur for biogenic gas products; Hochtemperatur-Entschwefelung fuer biogene Produktgase. Design und Optimierung - Schlussbericht/Jahresbericht

    Energy Technology Data Exchange (ETDEWEB)

    Schildhauer, T.; Biollaz, S.

    2009-12-15

    This final report for the Swiss Federal Office of Energy (SFOE) presents the results of a project concerning the development of basics ideas on the design and optimisation of high-temperature methods for the removal of sulphur from biogenic gas products. Tests made as part of the 'Methane from Wood' project at pilot installations in Switzerland and Austria are discussed. Low temperature and high-temperature methods are examined and discussed. A number of sulphur compounds were tested. Also, experiments made using nickel, HDS and CPO catalysers are discussed.

  14. Sulphur highways : value-added solutions to create sulphur demand

    Energy Technology Data Exchange (ETDEWEB)

    Macedo, R.

    2010-09-15

    Producers generally view sulphur as a nuisance with essentially no benefit. In Alberta, a greater portion of sulphur production will shift from natural gas to the oilsands producing areas where there is limited infrastructure to move it out. Increased amounts of sour oil and gas production together with greater fuel desulphurization have also led to more sulphur being produced. In order to address the inevitable storage issue, Shell is considering value-added uses for the product, such as sulphur asphalt. The company developed Thiopave, a sulphur-based product for use in asphalt paving mixtures that can improve the mechanical performance of asphalt. The sulphur can be added to the asphalt mix as a solid pellet, which helps reduce the emission of sulphur vapour, odour and eye irritation. Twenty Thiopave projects are planned for the 2010 paving season in 9 U.S. states and 2 Canadian provinces. Sulphur Enhanced Asphalt Modifier (SEAM) was the first generation of Thiopave developed in 2003. SEAM replaces 20 to 25 percent by volume of the bitumen in asphalt mix. The properties allow Thiopave-enhanced roads to perform better than conventional roads in both consistently high temperature regions and climates with wide temperature variations. In 2007, an asphalt mix containing 40 percent by mass of Thiopave was used in a trial in Qatar. The Thiopave asphalt mix was compared with a conventional mix at temperatures ranging from 10 to 40 degrees C to determine the stiffness ratio. It was determined that Thiopave mixes containing high-penetration bitumen can be used to build temperature resistant roads that are stiffer in hot summer temperatures while improving the pavement's cold weather cracking performance. 1 ref., 4 figs.

  15. Sulphur output from oil sands : dramatically changing Alberta's sulphur balance

    Energy Technology Data Exchange (ETDEWEB)

    D' Aquin, G. [Con-Sul Inc., Bigfork, MT (United States)

    2008-07-01

    This paper discussed sulphur production from Alberta's gas and oil sands industries. While sulfur derived from natural gas production in the province is expected to decline as natural gas reserves diminish, Alberta's oil sands contain high amounts of sulphur. It is not yet known how much sulphur will be produced from the province's oil sands facilities. Alberta had considerable stockpiles of sulphur in the 1970s. By 1980, inventories began to decline. By 1996, output had increased to 7.1 million tonnes. Alberta's sulphur inventory reached 9.7 million tonnes following the collapse of the Soviet Union's government mandated fertilizer industry. In 2006, sulphur supplies in Alberta reached 12 million tonnes. Reduced global output has now lowered sulphur stockpiles. Increases in sulphur prices tend to reduce market demand, and lower prices will not typically change the volume of sulphur produced as a byproduct of oil and gas operations. Bitumen-derived sulphur output is expected to exceed gas-derived sulphur output in the near future. Sulphur from oil sands processing is expected to increase by 5 million tonnes by 2017. Increased sulphur production levels in Alberta will present a significant challenge for all sectors of the hydrocarbon industry. It was concluded that developing a plan for storing, selling or disposing of the sulphur will help to ensure the profitability of oil sands operations.

  16. Effects of changes in the UK energy demand and environmental legislation on atmospheric pollution by sulphur dioxide

    International Nuclear Information System (INIS)

    Blakemore, F.B.; Davies, C.; Isaac, J.G.

    1999-01-01

    Ninety-nine percent of the sulphur dioxide generated over the period 1970 to 1994 arose from the combustion of fossil fuels in the energy sector. The annual mass emission of sulphur dioxide has fallen by 58% over this period, due to the reductions in outputs from coal and petroleum fired plants. The influence of natural-gas power generation has played an important part in this reduction. Four major pieces of environmental legislation have been enacted to control sulphur-dioxide emissions: the Control of Pollution Act 1974, and three EEC Directives are discussed. The UK emissions in 1994 were 49% below the 1980 baseline and 9% ahead of the 1998 EU target level. The protocol on the reduction of sulphur-dioxide emissions, adopted in 1985, required a cut in the total SO 2 emissions of 30% by 1993, based on 1980 levels. The UK achieved a reduction of 37% by the end of 1993. Sulphur-dioxide emissions are predicted to fall according to the six scenarios in Energy paper 65 as a reference case. The predicted decline is in line with the UNECE targets set for 2010. (Copyright (c) 1999 Elsevier Science B.V., Amsterdam. All rights reserved.)

  17. Study of the corrosion of metallic coatings and alloys containing aluminum in a mixed atmosphere - sulphur, oxygen - at high temperatures

    International Nuclear Information System (INIS)

    Fellmann, Daniel

    1982-01-01

    The objective of this research thesis is the development of materials for a sulphur experimental loop allowing the thermodynamic properties of such an energy cycle to be checked. As solutions must comply with industrial methods, rare materials are excluded as they are too expensive or difficult to implement. Iron-based materials have been tested but could not have at the same time a good corrosion resistance and high temperature forming and mechanical toughness properties. Therefore, metallic coatings have been chosen, specifically alumina. After having reported a bibliographical study on corrosion by sulphur vapour and by oxygen and by sulphur-oxygen, the author presents the experimental materials and methods. Then, the author reports the study of mixed corrosion (by sulphur and oxygen together) of metallic alloys (ferritic and austeno-ferritic alloys, aluminium and titanium alloys), and of the corrosion of FeAlx coatings, of AlTix alloys [fr

  18. Forest fuel and sulphur

    International Nuclear Information System (INIS)

    Lundborg, A.

    1994-10-01

    This report illustrates the sulphur cycle in forest fuel and in the forest ecosystem. The hypothesis is that sulphur dioxide from combustion of forest fuel is not more acidifying than sulphur that is mineralized from tree biomass if it is left in the forest instead of being burnt. The report gives an overview of the sulphur cycle in general together with the acidifying effect of sulphur. The sulphur content in wood biomass is about 1 mg/g in the needles and 0.2-0.3 mg/g in wood. Chipped forest fuel contains 0.2-0.5 mg S/g. A removal of 40 tonnes of felling residues per hectare may contain about 8-30 kg S. The sulphur occurs both in organic, often reduced, form and as sulphate. In situations of high availability to sulphur there will be an increased proportion of sulphate. After combustion some, perhaps half, of the sulphur is left in the ashes, most of which appears to be sulphate. In mineralisation of reduced organic sulphur, of type R-SH, the sulphur is released in the form of sulphide. Hydrogen sulphide, H2S, can be oxidised by microbes to sulphate, which should be acidifying (2 H+ will remain). A very rough estimate suggests that emissions of sulphur dioxide from forest fuel, spread over the period the trees are growing, and on the area from which the trees are taken, corresponds to 0.5% of the sulphur deposition in southern Sweden. Sulphur emissions from biofuel combustion are much lower than Sweden's and the EU's most stringent emission limits for coal. Whole-tree removal with return of ashes will theoretically give a considerable reduction in soil acidity since large quantities of nitrogen are removed and thus the acidifying effect of nitrogen will not occur. This should be of greater importance for forest acidification than the effect of biomass sulphur. 80 refs, numerous tabs

  19. Unstacked double-layer templated graphene for high-rate lithium-sulphur batteries

    Science.gov (United States)

    Zhao, Meng-Qiang; Zhang, Qiang; Huang, Jia-Qi; Tian, Gui-Li; Nie, Jing-Qi; Peng, Hong-Jie; Wei, Fei

    2014-03-01

    Preventing the stacking of graphene is essential to exploiting its full potential in energy-storage applications. The introduction of spacers into graphene layers always results in a change in the intrinsic properties of graphene and/or induces complexity at the interfaces. Here we show the synthesis of an intrinsically unstacked double-layer templated graphene via template-directed chemical vapour deposition. The as-obtained graphene is composed of two unstacked graphene layers separated by a large amount of mesosized protuberances and can be used for high-power lithium-sulphur batteries with excellent high-rate performance. Even after 1,000 cycles, high reversible capacities of ca. 530 mA h g-1 and 380 mA h g-1 are retained at 5 C and 10 C, respectively. This type of double-layer graphene is expected to be an important platform that will enable the investigation of stabilized three-dimensional topological porous systems and demonstrate the potential of unstacked graphene materials for advanced energy storage, environmental protection, nanocomposite and healthcare applications.

  20. Sumpor u ugljenu (Sulphur in Coal

    Directory of Open Access Journals (Sweden)

    Rađenović, A.

    2004-12-01

    Full Text Available The presence of sulphur in coal possesses important environmetal problems in its usage. The sulphur dioxide (S02 emissions produced during coal combustion account for a significant proportion of the total global output of anthropogenic SO2. The extent of sulphur separation depends on several variables such as the form of sulphur in coal, intimacy of contact between minerals and the products of devolatilization. The total sulphur in coal varies in the range of 0.2 - 11 wt %, although in most cases it is beetwen 1 and 3 wt %. Sulphur occurs in a variety of both inorganic and organic forms. Inorganic sulphur is found mainly as iron pyrite, marcasite, pyrrhotite, sphalerite, galena, chalcopirite and as sulphates (rarely exceeds w = 0,1 %. Organic sulphur is found in aromatic rings and aliphatic functionalities usually as mercaptans, aliphatic and aryl sulfides, disulfides and thiophenes. Organic and pyritic sulphur quantities depend on coal rank. Higher rank coals tend to have a high proportion of labile sulphur. All the organic sulphur is bivalent and it is spread throughout the organic coal matrix. Sulphur occurs in all the macerals and most minerals. Vitrinite contains the major part of organic sulphur and metals. Elemental sulphur is produced during coal weathering. The depolymerization methods as pyrolysis and hydrogenation are very drastic methods wich change the structure of the coal and the sulphur groups. In the case of pyrolysis, high levels of desulphurization, in chars and additional production of liquid hydrocarbon can be achieved. Thiophenes and sulphides were the major sulphur components of tars from coal pyrolysis. Hyrdogen sulphide and the lower mercaptans and sulphides were found in the volatile matters. Hydrogen sulphide and thiophenes are practically the only sulphur products of coal hydrogenation. H2S is produced in char hydrodesulphurization. A number of options are available for reducing sulphur emissions including the

  1. Sulphur in Poland

    Directory of Open Access Journals (Sweden)

    Seman Peter

    2001-12-01

    Full Text Available Poland belongs to one of the last countries with native sulphur mining. Its history begun in 15th century. Deposit area of Tarnobrzeg re-presents 80% of all known sulphur reserves in this country. All of explored deposits in this area were created by metasomatic alteration of sulphur bearing limestones with sulphur mineralised liquids, which arised from melt gypsum. The average content is 25 - 30% of sulphur in Tarnobrzeg area. Considerable parts of deposits are created by calcite and native sulphur. Gypstone, baryte and stroncianite have only minera-logic occurencies. The extensive native sulphur deposits account for 88% of the country´s sulphur production. There were five sulphur mines in operation: Jeziórko, Grêbów, Machów I, Machów II and Basznia, but operations in Basznia were ended in 1992 and Machów and Machów II were liquidated. The sixth mine Osiek is currently producing. Only the Machów I mine operated an open-pit extraction and refining process, the other four mines producing sulphur using a modified Frasch method that gives elemental sulphur of up to 99,9% purity. Sulphur is an important export commodity with foreign sales totalling around 1.5 - 2.5 Mt/y. Modern benefication methods, which allowing to achieve sulphur from hydrocarbons, are causing decrease of native sulphur prices in the world and bringing about reduction of mining activities for this raw material in Poland.

  2. Mathematical modelling of demineralisation of high sulphur coal by bioleaching

    Energy Technology Data Exchange (ETDEWEB)

    Weerasekara, N.S.; Frutos, F.J.G.; Cara, J.; Lockwood, F.C. [University of London Imperial College of Science Technology & Medicine, London (United Kingdom)

    2008-02-15

    During coal combustion various toxic compounds are generated from its sulphur content. Their environmental impacts are considered to be very important. While there are various conventional preparation methods to remove the sulphur in the fuel, recent work reveals that newly-isolated micro-organisms, naturally present in coal, have the ability to reduce its sulphur content. The removal of sulphur using biological leaching involving acidophilic iron oxidising bacteria like Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans are examined and a computational technique based on computational fluid dynamics is developed to model the biological leaching of sulphur from coal. The model was validated against a pack-column experiment carried out for iron separation during 60 days. The mathematical model predicted iron separation over time is similar to experimental measurements, with an average difference of 5.5%. According to the experimental results, there was an overall reduction of 33% of pyrite, whereas the model prediction was 32%. The model results shows overall good agreement with pack-column experimental data.

  3. Nuclear physical express analysis of solid fuel sulphur content

    International Nuclear Information System (INIS)

    Pak, Yu.; Ponomaryova, M

    2005-01-01

    Full text: Sulphur content is an important qualitative coal parameter. The problem of coal sulphur content determining remains one of the most important both in Kazakhstan and in other coal-mining countries. The traditional method of sampling, the final stage of which is chemical analysis of coal for sulphur, is characterized by high labour intensity and low productivity. That's why it is ineffective for mass express analytical quality control and technological schemes of coal processing control. In this connection it is very urgent to develop a method of coal sulphur content on the base of a series nuclear-geophysical equipment with an isotope source of primary radiation, allowing to increase analysis representativity and maximally take into account coal real composition inconstancy. To solve the problem set it is necessary to study the main laws of X-ray-radiometric method applied to the coal quality analysis for working out instrumental methods of speed determining of coal sulphur content with satisfactory accuracy for technological tasks, to determine laws of changing the flows of characteristic X-ray and scattered radiation from coal sulphur content of various real composition and to optimize methodical and hardware parameters, providing minimal error of sulphur content control. On the base of studying laws of real composition coal components and their interconnections with sulphur content there has been substantiated the expediency of using hardware functions of calcium and iron to control coal sulphur contents; there has been suggested a model to estimate the methodical error of coal sulphur content determining on the base of the data about sensitivity to sulphur and effecting factors using ultimate methods of coal components substitution methods allowing to optimize sulphur control parameters; there has been worked out an algorithm of X-ray-radiometric control of sulphur content based on the sequential radiating the analyzed coal with gamma-radiation of

  4. Effects of sulphur ion implantation on the electrochemical behaviour of two stainless steels in sulphuric medium

    International Nuclear Information System (INIS)

    Nader-Roux, J.; Becdelievre, A.M. de; Gaillard, F.; Roux, R.; Becdelievre, J. de

    1986-01-01

    The electrochemical behaviour in sulphuric acid of two austenitic stainless steels (AISI 304 L and AISI 321) modified by sulphur ion implantation has been studied. Surface analysis of oxygen and sulphur by LEEIXS and XRFS were performed before and after polarization on unimplanted and on implanted samples. I/E curves with implanted steels reveal an important corrosion peak (α peak) recovering widely the active peak of unimplanted samples. For high implanted doses, another peak (β peak) appears in the passive range. High doses implanted steels polarized in the range of the α peak exhibit a sulphur enriched black surface layer. SEM examination of this layer shows it is constituted by flakes rolling up themselves. The formation of a superficial non-protective sulphide layer and the internal stresses of this layer explain the corrosion enhancement of sulphur implanted materials. After dissolution of this layer the behaviour of unimplanted steels is found again. (author)

  5. Effect of sulphur forms on colour and residue of sulphur during the storage at drying grapes by sulphur

    Directory of Open Access Journals (Sweden)

    Boztepe Özlem

    2016-01-01

    Full Text Available Turkey is the world leader in the manufacture and export of seedless raisins. Requirement of golden bleached raisins is increasing in food Industry of especially cake, bread and pastry year by year. In this research, the lowest residual value and the practical realization of such production was intended to determine by drying grapes with application of sulphur. In this case, sulphur residue and colour situations were determined during 12-mounth-storage according to sulphur forms. In this study sulphur studies were applied by Vitis Vinifera cv. “Sultani Çekirdeksiz” with Na2S2O5, which is liquid source of sulphur and SO2, which is gas source of sulphur. SO2 application were studied during 3, 6 and 8 hours and liquid form of sulphur is Na2S2O5 that was used during by 10, 20 and 30 minutes. Applications were prepared with 3 replicates which contain 20 kg fresh grape in each replicate. In conclusion, changes in dried grape have been identified in point of colour (chroma and hue and the sulphur content was determined according to sulphur forms in packing. Gas form of sulphur (SO2 which was applied 3 hours, gave the best result during 12-mounth-storage for colour and sulphur residue.

  6. Reinforced sulphur concrete

    NARCIS (Netherlands)

    2014-01-01

    Reinforced sulphur concrete wherein one or more metal reinforcing members are in contact with sulphur concrete is disclosed. The reinforced sulphur concrete comprises an adhesion promoter that enhances the interaction between the sulphur and the one or more metal reinforcing members.

  7. High-performance graphene/sulphur electrodes for flexible Li-ion batteries using the low-temperature spraying method

    Science.gov (United States)

    Kumar, Pushpendra; Wu, Feng-Yu; Hu, Lung-Hao; Ali Abbas, Syed; Ming, Jun; Lin, Chia-Nan; Fang, Jason; Chu, Chih-Wei; Li, Lain-Jong

    2015-04-01

    Elementary sulphur (S) has been shown to be an excellent cathode material in energy storage devices such as Li-S batteries owing to its very high capacity. The major challenges associated with the sulphur cathodes are structural degradation, poor cycling performance and instability of the solid-electrolyte interphase caused by the dissolution of polysulfides during cycling. Tremendous efforts made by others have demonstrated that encapsulation of S materials improves their cycling performance. To make this approach practical for large scale applications, the use of low-cost technology and materials has become a crucial and new focus of S-based Li-ion batteries. Herein, we propose to use a low temperature spraying process to fabricate graphene/S electrode material, where the ink is composed of graphene flakes and the micron-sized S particles prepared by grinding of low-cost S powders. The S particles are found to be well hosted by highly conductive graphene flakes and consequently superior cyclability (~70% capacity retention after 250 cycles), good coulombic efficiency (~98%) and high capacity (~1500 mA h g-1) are obtained. The proposed approach does not require high temperature annealing or baking; hence, another great advantage is to make flexible Li-ion batteries. We have also demonstrated two types of flexible batteries using sprayed graphene/S electrodes.Elementary sulphur (S) has been shown to be an excellent cathode material in energy storage devices such as Li-S batteries owing to its very high capacity. The major challenges associated with the sulphur cathodes are structural degradation, poor cycling performance and instability of the solid-electrolyte interphase caused by the dissolution of polysulfides during cycling. Tremendous efforts made by others have demonstrated that encapsulation of S materials improves their cycling performance. To make this approach practical for large scale applications, the use of low-cost technology and materials has become

  8. Oxidation of inorganic compounds of sulphur by various sulphur bacteria

    Energy Technology Data Exchange (ETDEWEB)

    Parker, C D; Prisk, J

    1953-01-01

    Cultures of thiobacillus thiooxidans, Th. thioparus, Th. novellus, Thiobacillus b strains t and kand Th. concretivorus, Thiobacillus x and the m strains, organisms isolated from concrete were examined to elucidate the mode of oxidation and to establish the identity of the organisms recently isolated from corroded concrete. Thiosulphate was oxidized by all these bacteria. Th. thiooxidans, Th. concretivorus and Thiobacillus x first converted it to tetrathionate and sulphate and then oxidized the tetrathionate to sulphate and free sulphuric acid. Thiobaciullus x differed from the other two in that, owing to a lesser acid tolerance, some tetrathionate was found in the final products of oxidation. Th. Thioparus converted thiosulphate to sulphate and sulphur, followed by partial oxidation of the sulphur to sulphuric acid. Th. novellus produced sulphate and sulphuric acid. Thiobacillus b, the t and k strains and the m strains formed sulphate and tetrathionate with temporary increase in pH value; only Thiobacillus x oxidized tetrationate, yielding sulphate and sulphuric acid. Elementary sulphur was oxidized by Th. thiooxidans, th. Concretivorus, thiobacillus x and Th. thioparus; the rates of oxidation decreased in that order, and the only product was sulphuric acid. Hydrogen sulphide was oxidized only at low concentrations and only by th. Concretivorus and Thiobacillus x; sulphuric acid was the end-product, and elementary sulphur may have been an intermediate. Thiobacillus x differed from Th. thiooxidans in pH range for growth and from Th. thioparus in its method of oxidation of thiosulphate, tetrathionate and H/sub 2/S. The m strains were similar to thiobacillus b and the t and k strains of trautwein.

  9. Sulphur uptake and yield of soybean as influenced by sulphur fertilization

    International Nuclear Information System (INIS)

    Shamima, N.; Farid, A. T. M.

    2005-01-01

    Effect of sulphur fertilization (0, 20, 40, 60 and 80 kg/ha) on sulphur uptake and seed yield was studied in sohag and Bangladesh soybean-4 varieties in the field of Bangladesh Agricultural Research Institute, Gazipur during the winter (rabi) seasons of 2000-2001 and 2001-2002 in grey Terrace soil (Albaquept). Addition of slphur fertilizer exerted significant influence on the yield attributes of soybean varieties. Sulphur uptake also significantly responded to the application of sulphur fertilizer. Variety Bangladesh soybean-4 was found superior to sohag in respect of sulphur uptake and yield. Greater sulphur utilization was observed at lower levels of fertilizer application. Seed yield and sulphur uptake were increased with the application of 40 kg/ ha for sohag and 60 kg/ha for Bangladesh soybean-4. Response of seed yield to added sulphur was quadratic. The economic optimum doses were found to be 49 kg s/ha for sohag and 52 kg s/ha for Bangladesh soybean-4, yielding 2060 and 2354 kg/ha, respectively. (author)

  10. Recent Development of Carbonaceous Materials for Lithium–Sulphur Batteries

    Directory of Open Access Journals (Sweden)

    Xingxing Gu

    2016-11-01

    Full Text Available The effects of climate change are just beginning to be felt, and as such, society must work towards strategies of reducing humanity’s impact on the environment. Due to the fact that energy production is one of the primary contributors to greenhouse gas emissions, it is obvious that more environmentally friendly sources of power are required. Technologies such as solar and wind power are constantly being improved through research; however, as these technologies are often sporadic in their power generation, efforts must be made to establish ways to store this sustainable energy when conditions for generation are not ideal. Battery storage is one possible supplement to these renewable energy technologies; however, as current Li-ion technology is reaching its theoretical capacity, new battery technology must be investigated. Lithium–sulphur (Li–S batteries are receiving much attention as a potential replacement for Li-ion batteries due to their superior capacity, and also their abundant and environmentally benign active materials. In the spirit of environmental harm minimization, efforts have been made to use sustainable carbonaceous materials for applications as carbon–sulphur (C–S composite cathodes, carbon interlayers, and carbon-modified separators. This work reports on the various applications of carbonaceous materials applied to Li–S batteries, and provides perspectives for the future development of Li–S batteries with the aim of preparing a high energy density, environmentally friendly, and sustainable sulphur-based cathode with long cycle life.

  11. Influence of sulphur and phosphorus on the hot deformation of Fe-Cr 13% high purity steel

    International Nuclear Information System (INIS)

    Lahreche, M.; Bouzabata, B.; Kobylanski, A.

    1995-01-01

    A series of Fe-Cr13%-C high purity steels containing increasing volume fractions of Sulphur (30, 60 and 100ppm) and Phosphorus (30, 60 and 100ppm) were prepared in order to study their hot deformation properties by tensile tests at various strain rates (10 -1 s -1 to 10 -4 s -1 ) and at temperatures from 700 C to 1100 C. It is observed that the hot ductility is lowered at 1000 C with the addition of sulphur. However, this decrease is relatively small (about 30% for 100ppm of sulphur) and quite similar for all additions of sulphur. When phosphorus is added, the embrittlement is along the whole deformed specimen. The usual criteria of ductility by parameter Z do not seem to be sufficient to describe this embrittlement. (orig.)

  12. Sulphur-containing compounds in sulphur-rich crude oils from hypersaline lake sediments and their geochemical implications

    NARCIS (Netherlands)

    Sinninghe Damsté, J.S.; Guoying, S.; Jiamo, F.; Brassell, S.C.; Gowar, A.P.; Eglinton, G.; Leeuw, J.W. de; Schenck, P.A.

    1987-01-01

    Three sulphur-rich commercial crude oils have been studied, which contain sulphur as high as up to 4 —12 %. These samples were collected from Tertiary hypersaline lake sediments of the Jianghan Basin, Hubei Province at different depths, but above the oil generation threshold (2200m). FPD-GC and

  13. CLINSULF sub-dew-point process for sulphur recovery

    Energy Technology Data Exchange (ETDEWEB)

    Heisel, M.; Marold, F.

    1988-01-01

    In a 2-reactor system, the CLINSULF process allows very high sulphur recovery rates. When operated at 100/sup 0/C at the outlet, i.e. below the sulphur solidification point, a sulphur recovery rate of more than 99.2% was achieved in a 2-reactor series. Assuming a 70% sulphur recovery in an upstream Claus furnace plus sulphur condenser, an overall sulphur recovery of more than 99.8% results for the 2-reactor system. This is approximately 2% higher than in conventional Claus plus SDP units, which mostly consist of 4 reactors or more. This means the the CLINSULF SSP process promises to be an improvement both in respect of efficiency and low investment cost.

  14. Sulphur recirculation for reduced boiler corrosion; Minskad pannkorrosion med svavelrecirkulation

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Sven; Karlsson, Martin (Goetaverken Miljoe AB, Goeteborg (Sweden)); Blomqvist, Evalena; Baefver, Linda; Claesson, Frida; Davidsson, Kent (SP Sveriges Tekniska Forskningsinstitut, Boraas (Sweden)); Froitzheim, Jan; Pettersson, Jesper; Steenari, Britt-Marie (Chalmers Tekniska Hoegskola, Oorganisk miljoekemi, Goeteborg (Sweden))

    2010-03-15

    Sulphur recirculation is a new technology for reducing boiler corrosion and dioxin formation, which was demonstrated in full-scale tests performed at the Renova Waste to Energy plant at Saevenaes in Goeteborg (Sweden). Sulphur is recirculated from the flue gas cleaning back to the boiler, which reduces the chloride content of the deposits, which in turn reduces boiler corrosion and dioxin formation. Sulphur dioxide was separated from the flue gas in a wet scrubber by adding hydrogen peroxide, producing sulphuric acid. The sulphuric acid was injected into the furnace using nozzles with atomization air, surrounded by recirculated flue gas for improved mixing. By recirculating the sulphur, the sulphur dioxide concentration was increased in the boiler. Each sulphur atom passed the boiler several times and no external sulphur had to be added. Dioxin, ash, deposits and particle samplings together with 1000 h corrosion probe measurements were performed for normal operation (reference) and with sulphur recirculation respectively. During spring 2009, reference measurements were made and the recirculation system was installed and tested. During autumn 2009, a long term test with sulphur recirculation was made. An SO{sub 2} concentration of approximately 800 mg/m3 (n, d.g.) was maintained in the boiler by the system except during a period of extremely low sulphur content in the waste. The sulphur dioxide stack concentrations have been far below the emission limit. Sulphuric acid dew point measurements have shown that the sulphuric acid dosage did not lead to elevated SO{sub 3} concentrations, which may otherwise lead to low temperature corrosion. The chlorine content of both fly ash and boiler ash decreased and the sulphur content increased during the sulphur recirculation tests. The molar chlorine/sulphur ratio (Cl/S) decreased by two thirds in the fly ash as well as in the boiler ash, except for one sample. With sulphur recirculation in operation, the deposit growth was

  15. High-performance graphene/sulphur electrodes for flexible Li-ion batteries using the low-temperature spraying method

    KAUST Repository

    Kumar, Pushpendra

    2015-01-01

    Elementary sulphur (S) has been shown to be an excellent cathode material in energy storage devices such as Li-S batteries owing to its very high capacity. The major challenges associated with the sulphur cathodes are structural degradation, poor cycling performance and instability of the solid-electrolyte interphase caused by the dissolution of polysulfides during cycling. Tremendous efforts made by others have demonstrated that encapsulation of S materials improves their cycling performance. To make this approach practical for large scale applications, the use of low-cost technology and materials has become a crucial and new focus of S-based Li-ion batteries. Herein, we propose to use a low temperature spraying process to fabricate graphene/S electrode material, where the ink is composed of graphene flakes and the micron-sized S particles prepared by grinding of low-cost S powders. The S particles are found to be well hosted by highly conductive graphene flakes and consequently superior cyclability (∼70% capacity retention after 250 cycles), good coulombic efficiency (∼98%) and high capacity (∼1500 mA h g-1) are obtained. The proposed approach does not require high temperature annealing or baking; hence, another great advantage is to make flexible Li-ion batteries. We have also demonstrated two types of flexible batteries using sprayed graphene/S electrodes. © The Royal Society of Chemistry 2015.

  16. Sulphur cement pre-composition and process for preparing such sulphur cement pre-composition

    NARCIS (Netherlands)

    2013-01-01

    The invention provides a process for the preparation of a sulphur cement pre-composition comprising reacting sulphur modifier with polysulphide-containing organosilane to obtain in the presence of sulphur the sulphur cement pre-composition, wherein the organosilane has the general molecular formula:

  17. Isotopic equilibria between sulphur solute species at high temperature

    International Nuclear Information System (INIS)

    Robinson, B.W.

    1978-01-01

    Sulphur solute species in ore solutions and geothermal discharges include HSO 4 - , SO 4 2- , H 2 S, and HS - , as well as the ion-paired species, NaHS 0 , NaHSO 4 - and Na 2 SO 4 0 . Observed sulphate-sulphide fractionation factors and the rates of attainment of isotopic equilibrium are likely to depend on the nature of the sulphur species actually taking part in these isotopic equilibria. Preliminary experiments in alkaline solution (pH 10.1 at 20 0 C) were carried out in a gold cell. No significant isotope fractionation was observed between the SO 4 2- and HS - in 29 days at 200 0 C, 63days at 300 0 C, or 90 days at 250 0 C. However, similar experiments at 350 0 C in sealed gold capsules at room temperature pH 8.5 showed slow exchange(t( 1 / 2 ) was calculated to be 510 days for the SO 4 2- -HS - exchange reaction using the theoretical fractionation of 20.2 0 / 00 ). The addition of NaCl appeared to have no affect on the exchange. However, pH strongly controls the reaction rate, and exchange probably involves H 2 S and the HSO 4 - ion. Additional preliminary experiments were conducted with a fivefold increase in the sulphur concentration; a decrease in t( 1 / 2 ) to 142 days resulted. Some inter-relationship between sulphur concentration and exchange rate thus exists. The important controlling parameters of isotope exchange (temperature, pH, and ΣS) can be seen to have influenced exchange in natural systems.(auth.)

  18. Design and modeling of an advanced marine machinery system including waste heat recovery and removal of sulphur oxides

    DEFF Research Database (Denmark)

    Frimann Nielsen, Rasmus; Haglind, Fredrik; Larsen, Ulrik

    2014-01-01

    the efficiency of machinery systems. The wet sulphuric acid process is an effective way of removing flue gas sulphur oxides from land-based coal-fired power plants. Moreover, organic Rankine cycles (ORC) are suitable for heat to power conversion for low temperature heat sources. This paper describes the design...... that an ORC placed after the conventional waste heat recovery system is able to extract the sulphuric acid from the exhaust gas, while at the same time increase the combined cycle thermal efficiency by 2.6%. The findings indicate that the technology has potential in marine applications regarding both energy...... and modeling of a highly efficient machinery system which includes the removal of exhaust gas sulphur oxides. The system consists of a two-stroke diesel engine, the wet sulphuric process for sulphur removal, a conventional steam Rankine cycle and an ORC. Results of numerical modeling efforts suggest...

  19. Sulphur fertilization influences the sulphur species composition in Allium sativum: sulphomics using HPLC-ICPMS/MS-ESI-MS/MS.

    Science.gov (United States)

    Raab, Andrea; Ronzan, Marilena; Feldmann, Joerg

    2017-10-18

    Garlic (A. sativum) contains a large number of small sulphur (S)-containing metabolites, which are important for its taste and smell and vary with A. sativum variety and growth conditions. This study was designed to investigate the influence of different sulphur-fertilization regimes on low molecular weight S-species by attempting the first sulphur mass balance in A. sativum roots and bulbs using HPLC-ICPMS/MS-ESI-MS/MS. Species unspecific quantification of acid soluble S-containing metabolites was achieved using HPLC-ICP-MS/MS. For identification of the compounds, high resolution ESI-MS (Orbitrap LTQ and q-TOF) was used. The plants contained up to 54 separated sulphur-containing compounds, which constitute about 80% of the total sulphur present in A. sativum. The roots and bulbs of A. sativum contained the same compounds, but not necessarily the same amounts and proportions. The S-containing metabolites in the roots reacted more sensitively to manipulations of sulphur fertilization than those compounds in the bulbs. In addition to known compounds (e.g. γ-glutamyl-S-1-propenylcysteine) we were able to identify and partially quantify 31 compounds. Three as yet undescribed S-containing compounds were also identified and quantified for the first time. Putative structures were assigned to the oxidised forms of S-1-propenylmercaptoglutathione, S-2-propenylmercaptoglutathione, S-allyl/propenyl-containing PC-2 and 2-amino-3-[(2-carboxypropyl)sulfanyl]propanoic acid. The parallel use of ICP-MS/MS as a sulphur-specific detector and ESI-MS as a molecular detector simplifies the identification and quantification of sulphur containing metabolites without species specific standards. This non-target analysis approach enables a mass balance approach and identifies the occurrence of the so far unidentified organosulphur compounds. The experiments showed that the sulphur-fertilization regime does not influence sulphur-speciation, but the concentration of some S

  20. Sulphurous Mineral Waters: New Applications for Health

    Directory of Open Access Journals (Sweden)

    Jose Manuel Carbajo

    2017-01-01

    Full Text Available Sulphurous mineral waters have been traditionally used in medical hydrology as treatment for skin, respiratory, and musculoskeletal disorders. However, driven by recent intense research efforts, topical treatments are starting to show benefits for pulmonary hypertension, arterial hypertension, atherosclerosis, ischemia-reperfusion injury, heart failure, peptic ulcer, and acute and chronic inflammatory diseases. The beneficial effects of sulphurous mineral waters, sulphurous mud, or peloids made from sulphurous mineral water have been attributed to the presence of sulphur mainly in the form of hydrogen sulphide. This form is largely available in conditions of low pH when oxygen concentrations are also low. In the organism, small amounts of hydrogen sulphide are produced by some cells where they have numerous biological signalling functions. While high levels of hydrogen sulphide are extremely toxic, enzymes in the body are capable of detoxifying it by oxidation to harmless sulphate. Hence, low levels of hydrogen sulphide may be tolerated indefinitely. In this paper, we review the chemistry and actions of hydrogen sulphide in sulphurous mineral waters and its natural role in body physiology. This is followed by an update of available data on the impacts of exogenous hydrogen sulphide on the skin and internal cells and organs including new therapeutic possibilities of sulphurous mineral waters and their peloids.

  1. Modification of oxide inclusions in calcium-treated Al-killed high sulphur steels

    NARCIS (Netherlands)

    Gollapalli, Veerababu; Rao, M.B.Venkata; Karamched, P.S.; Borra, C.R.; Roy, G.G.; Srirangam, Prakash

    2018-01-01

    A study has been carried out to understand the modification of alumina inclusions in Al-killed high sulphur steel with calcium treatment. For calcium treatment to be effective, a general practice is to desulphurise the steel to prevent the formation of solid CaS inclusions that are harmful to

  2. Concentration of volatile sulphur-containing compounds along the gastrointestinal tract of pigs fed a high-sulphur or a low-sulphur diet

    DEFF Research Database (Denmark)

    Poulsen, Henrik Vestergaard; Canibe, Nuria; Finster, Kai

    2010-01-01

    Volatile sulphur-containing compounds (VSC) are formed in large quantities in the gastrointestinal tract (GI-tract) of pigs and upon excretion from the animal; these compounds are released from the faeces causing emission of foul odour. However, very little is known about the rate and extent of t...

  3. Impact of sulphur fumigation on the chemistry of ginger.

    Science.gov (United States)

    Wu, Cheng-Ying; Kong, Ming; Zhang, Wei; Long, Fang; Zhou, Jing; Zhou, Shan-Shan; Xu, Jin-Di; Xu, Jun; Li, Song-Lin

    2018-01-15

    Ginger (Zingiberis Rhizoma), a commonly-consumed food supplement, is often sulphur-fumigated during post-harvest handling, but it remains unknown if sulphur fumigation induces chemical transformations in ginger. In this study, the effects of sulphur fumigation on ginger chemicals were investigated by ultra-high performance liquid chromatography coupled with quadrupole time-of-flight mass spectrometry (UHPLC-QTOF-MS/MS)-based metabolomics. The results showed that sulphur fumigation significantly altered the holistic chemical profile of ginger by triggering chemical transformations of certain original components. 6-Gingesulphonic acid, previously reported as a naturally-occurring component in ginger, was revealed to be a sulphur fumigation-induced artificial derivative, which was deduced to be generated by electrophilic addition of 6-shogaol to sulphurous acid. Using UHPLC-QTOF-MS/MS extracting ion analysis with 6-gingesulphonic acid as a characteristic chemical marker, all the commercial ginger samples inspected were determined to be sulphur-fumigated. The research outcomes provide a chemical basis for further comprehensive safety and efficacy evaluations of sulphur-fumigated ginger. Copyright © 2017 Elsevier Ltd. All rights reserved.

  4. Sulphurous mineral waters

    Directory of Open Access Journals (Sweden)

    Iluta Alexandru

    2011-09-01

    Full Text Available Sulphurous waters contain at least 1mg H2S, HS, S or thiosulphate per liter or complex colloidal sulfur water is presented as of simple or mixed sulphide (alkali, carbonated, chlorinated sodium.In the sulphurous waters, sulfur is found in several forms (hydrogen sulfide, free sulfide, sulfide groups, polysulfides acids. Yellow, opalescent white precipitate and deposit a glass of water on the bottom of sulphur oxidation by indicates the intensity of the wateroxidation process by oxygen in the air.

  5. Enhanced high temperature thermoelectric response of sulphuric acid treated conducting polymer thin films

    KAUST Repository

    Sarath Kumar, S. R.; Kurra, Narendra; Alshareef, Husam N.

    2015-01-01

    We report the high temperature thermoelectric properties of solution processed pristine and sulphuric acid treated poly(3, 4-ethylenedioxythiophene):poly(4-styrenesulfonate) (or PEDOT:PSS) films. The acid treatment is shown to simultaneously enhance the electrical conductivity and Seebeck coefficient of the metal-like films, resulting in a five-fold increase in thermoelectric power factor (0.052 W/m. K ) at 460 K, compared to the pristine film. By using atomic force micrographs, Raman and impedance spectra and using a series heterogeneous model for electrical conductivity, we demonstrate that acid treatment results in the removal of PSS from the films, leading to the quenching of accumulated charge-induced energy barriers that prevent hopping conduction. The continuous removal of PSS with duration of acid treatment also alters the local band structure of PEDOT:PSS, resulting in simultaneous enhancement in Seebeck coefficient.

  6. Enhanced high temperature thermoelectric response of sulphuric acid treated conducting polymer thin films

    KAUST Repository

    Sarath Kumar, S. R.

    2015-11-24

    We report the high temperature thermoelectric properties of solution processed pristine and sulphuric acid treated poly(3, 4-ethylenedioxythiophene):poly(4-styrenesulfonate) (or PEDOT:PSS) films. The acid treatment is shown to simultaneously enhance the electrical conductivity and Seebeck coefficient of the metal-like films, resulting in a five-fold increase in thermoelectric power factor (0.052 W/m. K ) at 460 K, compared to the pristine film. By using atomic force micrographs, Raman and impedance spectra and using a series heterogeneous model for electrical conductivity, we demonstrate that acid treatment results in the removal of PSS from the films, leading to the quenching of accumulated charge-induced energy barriers that prevent hopping conduction. The continuous removal of PSS with duration of acid treatment also alters the local band structure of PEDOT:PSS, resulting in simultaneous enhancement in Seebeck coefficient.

  7. THE SOLUBILITY OF MILAS BAUXITE ORE IN SULPHURIC ACI

    Directory of Open Access Journals (Sweden)

    Mustafa GULFEN

    2001-06-01

    Full Text Available The effects of calcination conditions,sulphuric acid concentrations and dissolvingtemperature and period as parameters to thesolubility of the bauxite ore from Gobekdagı reservesin Mugla-Milas region were investigated. The bauxitesamples were calcined in different periods at differenttemperatures. Then the solubility of the calcinedbauxite samples in sulphuric acid solution wasexamined. Dissolving activation energy (Ea wascalculated using the optimum kinetics equation andthe results obtained from the solubility studiesexamined dissolving temperatures and periods

  8. Biological parameters in technogenic soils of a former sulphur mine

    Science.gov (United States)

    Siwik-Ziomek, Anetta; Brzezińska, Małgorzata; Lemanowicz, Joanna; Koper, Jan; Szarlip, Paweł

    2018-04-01

    This study was conducted on the soils originating from a reclamation area of the former sulphur mine in Tarnobrzeg, Poland. Soil was sampled 16 years after the completion of mining works with the open-pit method at Machów, as well as 7 years after sulphur mining via the `smelting' method in the Jeziórko mine was abandoned. Several biological parameters were examined: soil respiration, soil microbial biomass and the activity of rhodanese and arylsulphatase enzymes taking part in sulphur transformation within the site's soils. The soils showed a high total sulphur and sulphates content. The SO42- constituted a large fraction of total sulphur, in some cases, exceeding 80% or even 95% of total sulphur. The soil pH decreased due to the degrading effects of sulphur mining. In the soils studied from the locations with the lowest soil pH value, no activity of arylsulphatase was reported and the activity of rhodanese was lowest. The highest soil respiration values were recorded from the 0-5 cm layer in the areas covered with forest vegetation. A high soil respiration value at the waste heap at Machów wherein a very high concentration of Stot and SO42- was observed can be due to the ability of fungi to produce hyphal strands and to survive unfavourable conditions.

  9. Organically bound sulphur in coal: A molecular approach

    NARCIS (Netherlands)

    Sinninghe Damsté, J.S.; Leeuw, J.W. de

    1992-01-01

    A critical review of literature concerning the molecular characterization of low and high molecular weight organosulphur constitutents present in coal as well as a detailed analysis of organic sulphur compounds present in flash evaporates and pyrolysates of a suite of coals ranging in sulphur

  10. Quantification of sulphur amino acids by ultra-high performance liquid chromatography in aquatic invertebrates.

    Science.gov (United States)

    Thera, Jennifer C; Kidd, Karen A; Dodge-Lynch, M Elaine; Bertolo, Robert F

    2017-12-15

    We examined the performance of an ultra-high performance liquid chromatography method to quantify protein-bound sulphur amino acids in zooplankton. Both cysteic acid and methionine sulfone were linear from 5 to 250 pmol (r 2  = 0.99), with a method detection limit of 13 pmol and 9 pmol, respectively. Although there was no matrix effect on linearity, adjacent peaks and co-eluting noise from the invertebrate proteins increased the detection limits when compared to common standards. Overall, performance characteristics were reproducible and accurate, and provide a means for quantifying sulphur amino acids in aquatic invertebrates, an understudied group. Copyright © 2017 Elsevier Inc. All rights reserved.

  11. A new approach for the determination of sulphur in food samples by high-resolution continuum source flame atomic absorption spectrometer.

    Science.gov (United States)

    Ozbek, N; Baysal, A

    2015-02-01

    The new approach for the determination of sulphur in foods was developed, and the sulphur concentrations of various fresh and dried food samples determined using a high-resolution continuum source flame atomic absorption spectrometer with an air/acetylene flame. The proposed method was optimised and the validated using standard reference materials, and certified values were found to be within the 95% confidence interval. The sulphur content of foods ranged from less than the LOD to 1.5mgg(-1). The method is accurate, fast, simple and sensitive. Copyright © 2014 Elsevier Ltd. All rights reserved.

  12. Use of stable sulphur isotopes to monitor directly the behaviour of sulphur in coal during thermal desulphurization

    Science.gov (United States)

    Liu, Chao-Li; Hackley, Keith C.; Coleman, D.D.

    1987-01-01

    A method has been developed using stable sulphur isotope analyses to monitor the behaviour of sulphur forms in a coal during thermal desulphurization. In this method, the natural stable isotopic composition of the pyritic and organic sulphur in coal is used as a tracer to follow their mobility during the desulphurization process. This tracer method is based on the fact that the isotopic compositions of pyritic and organic sulphur are significantly different in some coals. Isotopic results of pyrolysis experiments at temperatures ranging from 350 to 750 ??C indicate that the sulphur released with the volatiles is predominantly organic sulphur. The pyritic sulphur is evolved in significant quantities only when pyrolysis temperatures exceed 500 ??C. The presence of pyrite seems to have no effect on the amount of organic sulphur evolved during pyrolysis. The chemical and isotopic mass balances achieved from three different samples of the Herrin (No. 6) coal of the Illinois Basin demonstrate that this stable isotope tracer method is quantitative. The main disadvantage of this tracing technique is that not all coals contain isotopically distinct organic and pyritic sulphur. ?? 1987.

  13. Polioencephalomalacia in ruminants caused by excessive amount of sulphur - a review

    Directory of Open Access Journals (Sweden)

    Lutnicki Krzysztof

    2014-06-01

    Full Text Available Polioencephalomalacia as a result of sulphur excess is a growing problem in cattle and sheep, mainly in young, growing animals. It is common in different regions of the world. The disease develops favoured by certain conditions such as sustained provision of feed and water with high sulphur content, use of dietary supplements containing sulphur, and a habitat with high hydrogen sulphide concentration. Pathogenesis of the disease is complex, but very important are oxidative-antioxidative imbalance, dysfunction of vessels, and secondary cerebral cortex ischaemia as a result of direct and/or indirect action of sulphur metabolites, namely hydrogen sulphide, sulphides, and sulphites. Clinical signs and changes in the cerebral cortex in the form of degenerative necrotic lesions are similar to those observed in polioencephalomalacia caused by vitamin B1 deficiency, and lead and salt intoxication. Highly increased sulphur content (more than 0.3-0.4 of dry matter in the diet is the basis for differential diagnosis, as well the high concentration of hydrogen sulphide in gas and sulphides in rumen fluid. In prophylaxis and treatment the most important measure is to limit sulphur intake and in acute cases to neutralise low pH in rumen and administer vitamin B1 injections.

  14. Passivation of chalcopyrite during the leaching with sulphuric acid solution in presence of sodium nitrate

    Directory of Open Access Journals (Sweden)

    Sokić Miroslav D.

    2010-01-01

    Full Text Available In this work, the process of the chalcopyrite leaching in sulphuric acid solution was investigated. Sodium nitrate was used as oxidant in the leaching process. Chemical reactions of leaching and their thermodynamic possibilities are predicted based on the calculated Gibbs energies and analysis of E−pH diagrams. The negative values of the Gibbs energy show that all chemical reactions are thermodynamically feasible at atmospheric pressure and in a temperature range 25-90°C. At high electrode potential and low pH values, Cu2+, Fe2+ and Fe3+ ions exist in water solutions. The increase of temperature reduces the probability of Fe3+ ion existence in the system. The chalcopyrite concentrate, enriched in the “Rudnik” flotation plant, with 27.08% Cu, 25.12% Fe, 4.15% Zn and 2.28% Pb was used in the work. XRD and DTA analysis of the concentrate reveals that the sample contains mainly the chalcopyrite with small amount of sphalerite. For the description of the reaction of leaching process the leach residuals, obtained at different conditions, were chosen for XRD, TG/DTA and SEM/EDX analyses. The elemental sulphur and chalcopyrite phases identified in leach residuals confirm our prediction that the elemental sulphur is formed during the leaching process. Accordingly, elemental sulphur is the main product of the reaction, while a minor amount of sulphide sulphur is oxidized to sulphate during the leaching. The sulphur formed during the reaction was precipitated at the particle surfaces, and slowed down the leaching rate in the final stage of leaching process. In the initial stage, the reaction rate was controlled by the surface reaction. The mechanism, latter has been changed into a diffusion controlled one.

  15. Role of sulphur in rice production

    International Nuclear Information System (INIS)

    Sachdev, Pamila; Sachdev, M.S.

    2002-01-01

    Sulphur is an essential plant nutrient growing in international importance. Rice farmers usually apply nitrogen, phosphorus and potassium at high rates to the crop. Whenever there is an imbalance between off take and input of nutrients, it may lead to a decline in soil fertility and increase incidence of deficiencies of certain plant nutrients especially sulphur and zinc. On the basis of available information, nutritional requirement, uptake values, crop response and measures to overcome S deficiency are some of the aspects critically dealt with

  16. Clean utilization of high sulphur petroleum coke by circulating fluidized bed combustion (CFBC) in Romania

    International Nuclear Information System (INIS)

    Dragos, L.; Flueraru, C.; Girjoaba, M.

    1996-01-01

    The economic and environmental problems caused by inefficient utilization of residual high-sulphur petroleum coke resulted from oil cracking in Romania is discussed. A special research programme applying CFBC technology has been carried out in the Institute for Power Equipment, Bucharest. The results from both laboratory facilities and pilot plant are presented. The main operating conditions and parameters are pointed out. Data on quality and composition of petroleum coke, combustion efficiency, temperature range in different zones and flue gas composition at distinct operating loads are given. The results obtained will be used for innovative design of CFBC boilers based on petroleum coke. A project for implementing a CFBC boiler in one of the Romanian oil refineries is being developed. An analysis of technical and economic advantages of these boilers for energy generation is presented

  17. Sulphur in liquid fuels 2002

    Energy Technology Data Exchange (ETDEWEB)

    Guthrie, J. [Environment Canada, Gatineau, PQ (Canada). Fuels Div., Oil, Gas and Energy Branch ; Sabourin, R. [Carleton Univ., Ottawa, ON (Canada)

    2003-08-01

    Environment Canada has developed new regulations for sulphur content in fuels in an effort to align with requirements recently passed by the U.S. Environmental Protection Agency. This report summarizes data regarding sulphur content in liquid fuels for the year 2002. The requirements of the Sulphur in Gasoline Regulation came into effect in 2002, limiting the average sulphur content of gasoline to 150 mg/kg. In January 2005, a 30 mg/kg average limit will come into effect. Also, in July 2002, the Sulphur in Diesel Fuel Regulation stipulated a maximum limit of 500 mg/kg for on-road diesel fuel. The new regulation continues this limit until mid-2006 at which time a 15 mg/kg limit will come into effect for on-road diesel fuel. Nationally, the average sulphur content in gasoline in 2002 was 246 mg/kg, which was 14.3 per cent lower than in 2001. The data covers the period from January 1 to December 31, 2002 and was obtained from petroleum refineries and importing companies that are required to submit quarterly information to the regional office of Environment Canada. Failure to comply results in penalties. The report includes data for aviation turbo fuel, motor gasoline, aviation gasoline, kerosene oil, low-sulphur diesel fuel, diesel fuel, light fuel oil, and heavy fuel oil. 16 tabs., 17 figs., 7 appendices.

  18. Origin of organic sulphur compounds and sulphur-containing high molecular weight substances in sediments and immature crude oils

    NARCIS (Netherlands)

    Sinninghe Damsté, J.S.; Rijpstra, W.I.C.; Leeuw, J.W. de; Schenck, P.A.

    1988-01-01

    The distribution patterns of Organic Sulphur Compounds (OSC), occurring in certain sediments and immature crude oils, were compared with those of the corresponding hydrocarbons. Because of the complexity of the OSC mixtures, they were desulphurized to hydrocarbons (n-alkanes, isoprenoid alkanes,

  19. Comparison of the SAWNUC model with CLOUD measurements of sulphuric acid-water nucleation.

    Science.gov (United States)

    Ehrhart, Sebastian; Ickes, Luisa; Almeida, Joao; Amorim, Antonio; Barmet, Peter; Bianchi, Federico; Dommen, Josef; Dunne, Eimear M; Duplissy, Jonathan; Franchin, Alessandro; Kangasluoma, Juha; Kirkby, Jasper; Kürten, Andreas; Kupc, Agnieszka; Lehtipalo, Katrianne; Nieminen, Tuomo; Riccobono, Francesco; Rondo, Linda; Schobesberger, Siegfried; Steiner, Gerhard; Tomé, António; Wimmer, Daniela; Baltensperger, Urs; Wagner, Paul E; Curtius, Joachim

    2016-10-27

    Binary nucleation of sulphuric acid-water particles is expected to be an important process in the free troposphere at low temperatures. SAWNUC (Sulphuric Acid Water Nucleation) is a model of binary nucleation that is based on laboratory measurements of the binding energies of sulphuric acid and water in charged and neutral clusters. Predictions of SAWNUC are compared for the first time comprehensively with experimental binary nucleation data from the CLOUD chamber at European Organization for Nuclear Research. The experimental measurements span a temperature range of 208-292 K, sulphuric acid concentrations from 1·10 6 to 1·10 9  cm -3 , and distinguish between ion-induced and neutral nucleation. Good agreement, within a factor of 5, is found between the experimental and modeled formation rates for ion-induced nucleation at 278 K and below and for neutral nucleation at 208 and 223 K. Differences at warm temperatures are attributed to ammonia contamination which was indicated by the presence of ammonia-sulphuric acid clusters, detected by an Atmospheric Pressure Interface Time of Flight (APi-TOF) mass spectrometer. APi-TOF measurements of the sulphuric acid ion cluster distributions ( (H2SO4)i·HSO4- with i = 0, 1, ..., 10) show qualitative agreement with the SAWNUC ion cluster distributions. Remaining differences between the measured and modeled distributions are most likely due to fragmentation in the APi-TOF. The CLOUD results are in good agreement with previously measured cluster binding energies and show the SAWNUC model to be a good representation of ion-induced and neutral binary nucleation of sulphuric acid-water clusters in the middle and upper troposphere.

  20. Energy, target, projectile and multiplicity dependences of intermittency behaviour in high energy O(Si,S) induced interactions

    International Nuclear Information System (INIS)

    Adamovich, M.I.; Alexandrov, Y.A.; Chernyavski, M.M.; Gerassimov, S.G.; Kharlamov, S.P.; Larionova, V.G.; Maslennikova, N.V.; Orlova, G.I.; Peresadko, N.G.; Salmanova, N.A.; Tretyakova, M.I.; Ameeva, Z.U.; Andreeva, N.P.; Anzon, Z.V.; Bubnov, V.I.; Chasnikov, I.Y.; Eligbaeva, G.Z.; Eremenko, G.Z.; Gaitinov, A.S.; Kalyachkina, G.S.; Kanygina, E.K.; Skakhova, C.I.; Bhalla, K.B.; Kumar, V.; Lal, P.; Lokanathan, S.; Mookerjee, S.; Raniwala, R.; Raniwala, S.; Burnett, T.H.; Grote, J.; Koss, T.; Lord, J.; Skelding, D.; Strausz, S.C.; Wilkes, R.J.; Cai, X.; Huang, H.; Liu, L.S.; Qian, W.Y.; Wang, H.Q.; Zhou, D.C.; Zhou, J.C.; Chernova, L.P.; Gadzhieva, S.I.; Gulamov, K.G.; Kadyrov, F.G.; Lukicheva, N.S.; Navotny, V.S.; Svechnikova, L.N.; Friedlander, E.M.; Heckman, H.H.; Lindstrom, P.J.; Garpman, S.; Jakobsson, B.; Otterlund, I.; Persson, S.; Soederstroem, K.; Stenlund, E.; Judek, B.; Nasyrov, S.H.; Petrov, N.V.; Xu, G.F.; Zheng, P.Y.

    1991-01-01

    Fluctuations of charged particles in high energy oxygen, silicon and sulphur induced interactions are investigated with the method of scaled factorial moments. It is found that for decreasing bin size down to δη∝0.1 the EMU01 data exhibits intermittent behaviour. The intermittency indexes are found to decrease with increasing incident energy and multiplicity and to increase with increasing target mass. It seems also to increase as the projectile mass increases. (orig.)

  1. A search for the sulphur hexafluoride cation with intense, few cycle laser pulses

    Energy Technology Data Exchange (ETDEWEB)

    Dota, Krithika; Mathur, Deepak, E-mail: atmol1@tifr.res.in [Tata Institute of Fundamental Research, 1 Homi Bhabha Road, Mumbai 400 005 (India); Centre for Atomic and Molecular Physics, Manipal University, Manipal 576 104 (India); Dharmadhikari, Aditya K. [Tata Institute of Fundamental Research, 1 Homi Bhabha Road, Mumbai 400 005 (India); Dharmadhikari, Jayashree A. [Centre for Atomic and Molecular Physics, Manipal University, Manipal 576 104 (India); Patra, Kaustuv; Tiwari, Ashwani K. [Indian Institute of Science Education and Research - Kolkata, Mohanpur 741 252 (India)

    2013-11-21

    It is well established that upon ionization of sulphur hexafluoride, the SF{sub 6}{sup +} ion is never observed in mass spectra. Recent work with ultrashort intense laser pulses has offered indications that when strong optical field are used, the resulting “bond hardening” can induce changes in the potential energy surfaces of molecular cations such that molecular ions that are normally unstable may, indeed, become metastable enough to enable their detection by mass spectrometry. Do intense, ultrashort laser pulses permit formation of SF{sub 6}{sup +}? We have utilized intense pulses of 5 fs, 11 fs, and 22 fs to explore this possibility. Our results are negative: no evidence is discovered for SF{sub 6}{sup +}. However, multiply charged sulphur and fluorine ions from highly charged SF{sub 6}{sup q+} ions are observed that enable us to resolve the controversy regarding the kinetic energy release accompanying formation of F{sup +} fragment ions. Quantum chemical computations of field-distorted potential energy curves of SF{sub 6} and its molecular ion enable us to rationalize our non-observation of SF{sub 6}{sup +}. Our findings have implications for high harmonic generation from SF{sub 6} in the few-cycle regime.

  2. Removing sulphur oxides from a fluid stream

    Science.gov (United States)

    Katz, Torsten; Riemann, Christian; Bartling, Karsten; Rigby, Sean Taylor; Coleman, Luke James Ivor; Lail, Marty Alan

    2014-04-08

    A process for removing sulphur oxides from a fluid stream, such as flue gas, comprising: providing a non-aqueous absorption liquid containing at least one hydrophobic amine, the liquid being incompletely miscible with water; treating the fluid stream in an absorption zone with the non-aqueous absorption liquid to transfer at least part of the sulphur oxides into the non-aqueous absorption liquid and to form a sulphur oxide-hydrophobic amine-complex; causing the non-aqueous absorption liquid to be in liquid-liquid contact with an aqueous liquid whereby at least part of the sulphur oxide-hydrophobic amine-complex is hydrolyzed to release the hydrophobic amine and sulphurous hydrolysis products, and at least part of the sulphurous hydrolysis products is transferred into the aqueous liquid; separating the aqueous liquid from the non-aqueous absorption liquid. The process mitigates absorbent degradation problems caused by sulphur dioxide and oxygen in flue gas.

  3. Pyroclastic sulphur eruption at Poas Volcano, Costa Rica

    Energy Technology Data Exchange (ETDEWEB)

    Francis, P.W.; Thorpe, R.S.; Brown, G.C.; Glasscock, J.

    1980-01-01

    The recent Voyager missions to Jupiter have highlighted the role of sulphur in volcanic processes on io. Although fumarolic sulphur and SO/sub 2/ gas are almost universal in terrestrial active volcanoes, and rare instances of sulphur lava flows have been reported, sulphur in a pyroclastic form has only been described from Poas Volcano, Costa Rica. Here we amplify the original descriptions by Bennett and Raccichini and describe a recent eruption of pyroclastic sulphur scoria and ejected blocks that are characterised by miniature sulphur stalactites and stalagmites.

  4. Sulphur mustard degradation on zirconium doped Ti-Fe oxides

    Energy Technology Data Exchange (ETDEWEB)

    Stengl, Vaclav, E-mail: stengl@iic.cas.cz [Department of Solid State Chemistry, Institute of Inorganic Chemistry AS CR v.v.i 250 68 Husinec-Rez (Czech Republic); Grygar, Tomas Matys [Department of Solid State Chemistry, Institute of Inorganic Chemistry AS CR v.v.i 250 68 Husinec-Rez (Czech Republic); Oplustil, Frantisek; Nemec, Tomas [Military Technical Institute of Protection Brno Veslarska 230, 628 00 Brno (Czech Republic)

    2011-09-15

    Highlights: {yields} New stechiometric materials for sulphur mustard degradation. {yields} High degree of degradation, more then 95% h{sup -1}. {yields} One-pot synthesis procedure. - Abstract: Zirconium doped mixed nanodispersive oxides of Ti and Fe were prepared by homogeneous hydrolysis of sulphate salts with urea in aqueous solutions. Synthesized nanodispersive metal oxide hydroxides were characterised as the Brunauer-Emmett-Teller (BET) surface area and Barrett-Joiner-Halenda porosity (BJH), X-ray diffraction (XRD), infrared (IR) spectroscopy, scanning electron microscopy (SEM) with energy-dispersive X-ray (EDX) microanalysis, and acid-base titration. These oxides were taken for an experimental evaluation of their reactivity with sulphur mustard (chemical warfare agent HD or bis(2-chloroethyl)sulphide). The presence of Zr{sup 4+} dopant tends to increase both the surface area and the surface hydroxylation of the resulting doped oxides in such a manner that it can contribute to enabling the substrate adsorption at the oxide surface and thus accelerate the rate of degradation of warfare agents. The addition of Zr{sup 4+} to the hydrolysis of ferric sulphate with urea shifts the reaction route and promotes formation of goethite at the expense of ferrihydrite. We discovered that Zr{sup 4+} doped oxo-hydroxides of Ti and Fe exhibit a higher degradation activity towards sulphur mustard than any other yet reported reactive sorbents. The reaction rate constant of the slower parallel reaction of the most efficient reactive sorbents is increased with the increasing amount of surface base sites.

  5. Preparation of combustible material from high sulphur coal by means of pyrolysis: magnetic separation; Obtencion de combustibles limpios a partir de carbones con altos contenidos en azure mediante procesos de pirolisis: separacion magnetica

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-11-01

    Basic studies on coal desulphurization by pyrolysis have been carried out with a series of low rank coals with high total sulphur contents and differences in the distribution of sulphur forms. The evolved sulphur compounds were studied by sulphide selective electrode H{sub 2}S and Fourier transform infrared (FTIR) spectroscopy. The mechanisms affecting the sulphur removal during pyrolysis have been studied by scanning electron microscopy coupled with energy dispersive X-ray (SEM-EDX), X-ray diffraction (XRD) and photoelectronic spectroscopy (XPS). A sample coal of 11 Tm, representative of the Teruel basins was processed at pilot scale in a rotary kiln (coal HR). A series of pyrolysis runs simulating the experimental conditions of the rotary kiln were also carried out in laboratory scale. The magnetic behaviour of the chars from the rotary kiln and from the lab-scale pyrolysis was tested. The efficiency of the desulphurization, including pyrolysis and magnetic separation, was calculated. Chars from rotary kiln were tested by thermogravimetric analysis, air reactivity and carbon efficiency combustion in fluidized bed.

  6. Sulphate sulphur concentration in vegetable crops, soil and ground water in the region affected by the sulphur dioxide emission from Plock oil refinery (central Poland)

    International Nuclear Information System (INIS)

    Mikula, W.

    1995-01-01

    Research was carried out in 1984-1990 in the region affected by the sulphur dioxide emission from one of the greatest oil refineries in Europe (Plock, central Poland). The sulphate sulphur concentration in the vegetable crops (red beet, carrot, parsley, bean, cabbage and dill), the soil and in ground water was defined in selected allotment gardens of Plock city and in a household garden located in the rural area about 25 km from the town. The highest amount of sulphur was found in the vegetable crops cultivated in the garden situated in the closest vicinity of the refinery. Sulphate sulphur contents harmful for plants (above 0.50 per cent d.m.) were noted in cabbage and carrot leaves in almost all the gardens (except one). The soil in all examined gardens was characterised by high sulphate sulphur concentration, which considerably exceeds the maximum amount admissible for light soil in Poland, i.e. 0.004 per cent d.m. The sulphate sulphur concentration in ground water in all the gardens exceeded the highest permissible content in drinking water in Poland. The sulphate sulphur content in the soil and ground water was not significantly dependent on the garden's distance from the refinery. Generally, the above normal sulphate sulphur concentrations occurred quite universally in the examined region and they concerned all the considered environmental components (vegetable crops, soil, ground water) and all the gardens. 22 refs., 6 tabs

  7. Sulphur in the Sculptor dwarf spheroidal galaxy. Including NLTE corrections

    NARCIS (Netherlands)

    Skúladóttir, Á.; Andrievsky, S. M.; Tolstoy, E.; Hill, V.; Salvadori, S.; Korotin, S. A.; Pettini, M.

    In Galactic halo stars, sulphur has been shown to behave like other α-elements, but until now, no comprehensive studies have been done on this element in stars of other galaxies. Here, we use high-resolution ESO VLT/FLAMES/GIRAFFE spectra to determine sulphur abundances for 85 stars in the Sculptor

  8. Investigating the significance of zero-point motion in small molecular clusters of sulphuric acid and water

    International Nuclear Information System (INIS)

    Stinson, Jake L.; Ford, Ian J.; Kathmann, Shawn M.

    2014-01-01

    The nucleation of particles from trace gases in the atmosphere is an important source of cloud condensation nuclei, and these are vital for the formation of clouds in view of the high supersaturations required for homogeneous water droplet nucleation. The methods of quantum chemistry have increasingly been employed to model nucleation due to their high accuracy and efficiency in calculating configurational energies; and nucleation rates can be obtained from the associated free energies of particle formation. However, even in such advanced approaches, it is typically assumed that the nuclei have a classical nature, which is questionable for some systems. The importance of zero-point motion (also known as quantum nuclear dynamics) in modelling small clusters of sulphuric acid and water is tested here using the path integral molecular dynamics method at the density functional level of theory. The general effect of zero-point motion is to distort the mean structure slightly, and to promote the extent of proton transfer with respect to classical behaviour. In a particular configuration of one sulphuric acid molecule with three waters, the range of positions explored by a proton between a sulphuric acid and a water molecule at 300 K (a broad range in contrast to the confinement suggested by geometry optimisation at 0 K) is clearly affected by the inclusion of zero point motion, and similar effects are observed for other configurations

  9. Feasibility of high-resolution continuum source molecular absorption spectrometry in flame and furnace for sulphur determination in petroleum products

    Science.gov (United States)

    Kowalewska, Zofia

    2011-07-01

    For the first time, high-resolution molecular absorption spectrometry with a high-intensity xenon lamp as radiation source has been applied for the determination of sulphur in crude oil and petroleum products. The samples were analysed as xylene solutions using vaporisation in acetylene-air flame or in an electrothermally heated graphite furnace. The sensitive rotational lines of the CS molecule, belonging to the ∆ν = 0 vibrational sequence within the electronic transition X 1∑ + → A 1П, were applied. For graphite furnace molecular absorption spectrometry, the Pd + Mg organic modifier was selected. Strong interactions with Pd atoms enable easier decomposition of sulphur-containing compounds, likely through the temporal formation of Pd xS y molecules. At the 258.056 nm line, with the wavelength range covering central pixel ± 5 pixels and with application of interactive background correction, the detection limit was 14 ng in graphite furnace molecular absorption spectrometry and 18 mg kg -1 in flame molecular absorption spectrometry. Meanwhile, application of 2-points background correction found a characteristic mass of 12 ng in graphite furnace molecular absorption spectrometry and a characteristic concentration of 104 mg kg -1 in flame molecular absorption spectrometry. The range of application of the proposed methods turned out to be significantly limited by the properties of the sulphur compounds of interest. In the case of volatile sulphur compounds, which can be present in light petroleum products, severe difficulties were encountered. On the contrary, heavy oils and residues from distillation as well as crude oil could be analysed using both flame and graphite furnace vaporisation. The good accuracy of the proposed methods for these samples was confirmed by their mutual consistency and the results from analysis of reference samples (certified reference materials and home reference materials with sulphur content determined by X-ray fluorescence

  10. Feasibility of high-resolution continuum source molecular absorption spectrometry in flame and furnace for sulphur determination in petroleum products

    Energy Technology Data Exchange (ETDEWEB)

    Kowalewska, Zofia, E-mail: zofia.kowalewska@obr.pl

    2011-07-15

    For the first time, high-resolution molecular absorption spectrometry with a high-intensity xenon lamp as radiation source has been applied for the determination of sulphur in crude oil and petroleum products. The samples were analysed as xylene solutions using vaporisation in acetylene-air flame or in an electrothermally heated graphite furnace. The sensitive rotational lines of the CS molecule, belonging to the {Delta}{nu} = 0 vibrational sequence within the electronic transition X{sup 1}{Sigma}{sup +} {yields} A{sup 1}{Pi}, were applied. For graphite furnace molecular absorption spectrometry, the Pd + Mg organic modifier was selected. Strong interactions with Pd atoms enable easier decomposition of sulphur-containing compounds, likely through the temporal formation of Pd{sub x}S{sub y} molecules. At the 258.056 nm line, with the wavelength range covering central pixel {+-} 5 pixels and with application of interactive background correction, the detection limit was 14 ng in graphite furnace molecular absorption spectrometry and 18 mg kg{sup -1} in flame molecular absorption spectrometry. Meanwhile, application of 2-points background correction found a characteristic mass of 12 ng in graphite furnace molecular absorption spectrometry and a characteristic concentration of 104 mg kg{sup -1} in flame molecular absorption spectrometry. The range of application of the proposed methods turned out to be significantly limited by the properties of the sulphur compounds of interest. In the case of volatile sulphur compounds, which can be present in light petroleum products, severe difficulties were encountered. On the contrary, heavy oils and residues from distillation as well as crude oil could be analysed using both flame and graphite furnace vaporisation. The good accuracy of the proposed methods for these samples was confirmed by their mutual consistency and the results from analysis of reference samples (certified reference materials and home reference materials with

  11. Changes in the content of water-soluble sulphur in the soil after an application of straw and elemental sulphur

    Directory of Open Access Journals (Sweden)

    Pavel Ryant

    2007-01-01

    Full Text Available The changes in the content of water-soluble sulphur in the soil after the application of straw and elemental sulphur (ES were explored in a 2-year vegetation pot experiment. The following variants were included in the experiment: 1 unfertilised control; 2 wheat straw; 3 rape straw; 4 ES; 5 wheat straw + ES; 6 rape straw + ES. The two types of straw were applied in a dose of 32 g of dry matter and elemental sulphur was applied in a dose of 0.42 g per pot, i.e. 6 kg of soil. The unsatisfactory C:N ratio in the straw was optimised to 25:1 by adding nitrogen in urea. Soil samples were taken prior to sowing of the model plant (spring wheat in 2005 and white mustard in 2006 and then in regular monthly intervals until harvesting (5 times a year. The content of water-soluble sulphur in the soil was evaluated by multifactorial analysis of variance monitoring the effect of the crop, date of soil sampling, application of straw and elemental sulphur.The contents of water-soluble sulphur differed statistically significantly (P > 0.999 when growing the individual model plants. When growing white mustard in 2006 the amount of available sulphur was by 1/5 higher and could have been partly affected by the warm year 2006, as compared to 2005 when spring wheat was grown. Significant differences (P > 0.999 were also discovered among the dates of soil sampling; higher values were detected before the sowing of model plants, i.e. after incubation in the winter, during vegetation the content of water-soluble sulphur decreased and sulphur showed the significantly highest values at the harvest of model plants. When wheat straw was applied the sulphur content did not increase and this may be associated with the wide C:S ratio, whereas after the application of rape straw the content of water-soluble sulphur increased by one third more than in the unfertilised control. The application of elemental sulphur also significantly increased the amount of water-soluble sulphur in

  12. Sulphur isotope measurements on sulphates from Antarctic atmospheric precipitations, lake waters and salt efflorescences: a contribution to the study of the natural sulphur cycle

    International Nuclear Information System (INIS)

    Wand, U.; Maass, I.; Haendel, D.

    1987-01-01

    Sulphur isotope analyses are an important tool for the study of the natural sulphur cycle. However, on the northern hemisphere such studies particularly of the atmospheric component of the cycle are seriously hampered and in many regions practically impossible because of the high emission rate of anthropogenic sulphur. Only in remote areas of the world such as the Antarctic 34 S analyses can be used with success to identify the various natural sulphur sources (marine, biogenic and volcanic sources). We report here preliminary results of 34 S isotope measurements on sulphates from recent atmospheric precipitations (snow), lake waters and salt efflorescences sampled in the Schirmacher Oasis and the Wohlthat Massif, central Queen Maud Land, East Antarctica. Except for 4 efflorescence samples the sulphates investigated in this work are enriched in 34 S relative to the meteoritic sulphur standard (CDT). On an average the sulphates of our study area are isotopically lighter than those from the McMurdo region, South Victoria land. The latter region is characterized by the predominance of salts of marine origin. (author)

  13. Quantitative Aspects of Sulphur Metabolism in the Ruminant

    Energy Technology Data Exchange (ETDEWEB)

    Landis, J. [Institut fuer Tierernaehrung, Eidgenoessische Technische Hochschule, Zurich (Switzerland)

    1968-07-01

    In a series of four experiments {sup 35}S sulphate was given intra-ruminally to lactating dairy goats at feeding times (twice daily) during periods of 10 to 11 d. Rumen contents were sampled on the 8th, 9th and 10th day of {sup 35}S application. Radioactivity was determined in the volatile sulphur fraction (sulphide-sulphur) and in protein-bound sulphur (fraction insoluble in trichloroacetic acid). The ratio between the specific activities of protein sulphur and of sulphide sulphur was considered to be an estimate for that fraction of sulphur-containing amino acids present in the proteins of rumen contents, which was synthesized by microorganisms. This interpretation is based on the assumption that sulphide is the most important source of inorganic sulphur for the synthesis of sulphur amino acids and that incorporation of inorganic sulphur compounds of a a higher state of oxidation into organic molecules may quantitatively be neglected. In three experiments the animals received rations containing 16% to 17% crude protein. In these experiments the ratio of specific activities of protein and sulphide sulphur was found to vary from 0.32 to 0.41. According to the assumptions mentioned above, this would indicate that 32 to 41% of the total amount of protein-bound sulphur amino acids were synthesized by microorganisms from inorganic (sulphide) sulphur. In the fourth experiment the animal received a ration containing only 10% protein but supplemented with urea to bring the total crude protein content to 13%. In this experiment the ratio of specific activities was 0.70, indicating a much higher contribution of microbial synthesis of sulphur amino acids than in the experiments with a more abundant protein supply. The time course of the specific activity of protein-bound-sulphur in the milk is taken as a reference base for an interpretation of labelling of body proteins in terms of turnover rates.

  14. Simultaneous analysis of gaseous and particulate sulphur in the atmosphere by x-ray fluorescence spectrometry

    International Nuclear Information System (INIS)

    Matsuda, Yatsuka; Mamuro, Tetsuo

    1975-01-01

    An analytical technique for the simultaneous measurements of the atmospheric concentrations of SO 2 gas and sulphur absorbed by aerosol particles has been developed. Aerosol particles are collected on membrane filter and at the same time SO 2 gas is captured on alkali impregnated filter. The sulphur content in each filter is measured by an energy dispersive X -ray fluorescence spectrometer consisting of a Si(Li) semiconductor detector connected to a multi-channel pulse height analyzer and an excitation source of 55 Fe. Two methods are acceptable for the determination of the sulphur content in impregnated filter by X-ray fluorescence analysis. In the first method X-ray fluorescence analysis is made after the collected sulphur gas diffused and distributed uniformly enough throughout the filter, and in the second method X-ray fluorescence analysis gas to be finished before the diffusion of the collected sulphur becomes appreciable. (author)

  15. Thermal stability studies on atomically clean and sulphur passivated InGaAs surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Chauhan, Lalit; Hughes, Greg [School of Physical Sciences, Dublin City University, Glasnevin, Dublin 9 (Ireland)

    2013-03-15

    High resolution synchrotron radiation core level photoemission measurements have been used to study the high temperature stability of sulphur passivated InGaAs surfaces and comparisons made with atomically clean surfaces subjected to the same annealing temperatures. Sulphur passivation of clean InGaAs surfaces prepared by the thermal removal of an arsenic capping layer was carried out using an in situ molecular sulphur treatment in ultra high vacuum. The elemental composition of the surfaces of these materials was measured at a series of annealing temperatures up to 530 C. Following a 480 C anneal In:Ga ratio was found to have dropped by 33% on sulphur passivated surface indicating a significant loss of indium, while no drop in indium signal was recorded at this temperature on the atomically InGaAs surface. No significant change in the As surface concentration was measured at this temperature. These results reflect the reduced thermal stability of the sulphur passivated InGaAs compared to the atomically clean surface which has implications for device fabrication. (Copyright copyright 2013 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  16. Assessment of sulphur and H2S corrosion by use of simultaneous ER, galvanic and optical measurements

    DEFF Research Database (Denmark)

    Hemmingsen, Tor; Hilbert, Lisbeth Rischel; Nielsen, Lars Vendelbo

    2003-01-01

    Sulphur and H2S corrosion on carbon steel is relevant in a range of industrial applications, including oil and gas production, district heating systems, and geothermal energy production. Bacterial activity may participate in the sulphur cycle and contribute to H2S production. As a part...

  17. Sulphur removal in IGCC projects

    Energy Technology Data Exchange (ETDEWEB)

    Cross, F. (Parsons (United Kingdom))

    1998-01-01

    The technology for recovering elemental sulphur from H[sub 2]S bearing gases is well established. The modified Claus Process is the principal work-horse in sulphur recovery and can customarily achieve conversion efficiencies of 95% or better. Nowadays, such a level of recovery is no longer sufficient in most instances and sulphur recovery facility must then include some form of enhanced recovery, usually by treating the Claus tail gas. A number of processes have been introduced to enable the overall recovery to be increased. Recoveries in excess of 99% are both feasible and economic. Use of oxygen in place has become very popular in cases where oxygen is available cheaply or where capacity increases are designed. Most IGCC projects needing an air separation plant would automatically benefit from extending the use of oxygen to the sulphur recovery plant. The most popular route to minimising sulphur emissions in the context of IGCC projects has involved an oxygen based Claus plant followed by tail gas hydrogenation, hydrogen sulphide recovery and its recycle to the Claus section. The recovery of H[sub 2]S from the Claus tail gas can be integrated with the main gas treating system in the gasification plant. The cost advantage of doing so is significant. Parsons has been involved with the technology since 1949 and has been responsible for developments such as the ammonia burning Claus and jointly with Unocal, the BSRP tail gas process and Selectox processes. Recent innovations in response changing environmental and production requirements have included catalytic and tail gas processes which reduce sulphur emissions. 6 figs., 2 tabs.

  18. Sulphur removal in IGCC projects

    Energy Technology Data Exchange (ETDEWEB)

    Cross, F. [Parsons (United Kingdom)

    1998-12-31

    The technology for recovering elemental sulphur from H{sub 2}S bearing gases is well established. The modified Claus Process is the principal work-horse in sulphur recovery and can customarily achieve conversion efficiencies of 95% or better. Nowadays, such a level of recovery is no longer sufficient in most instances and sulphur recovery facility must then include some form of enhanced recovery, usually by treating the Claus tail gas. A number of processes have been introduced to enable the overall recovery to be increased. Recoveries in excess of 99% are both feasible and economic. Use of oxygen in place has become very popular in cases where oxygen is available cheaply or where capacity increases are designed. Most IGCC projects needing an air separation plant would automatically benefit from extending the use of oxygen to the sulphur recovery plant. The most popular route to minimising sulphur emissions in the context of IGCC projects has involved an oxygen based Claus plant followed by tail gas hydrogenation, hydrogen sulphide recovery and its recycle to the Claus section. The recovery of H{sub 2}S from the Claus tail gas can be integrated with the main gas treating system in the gasification plant. The cost advantage of doing so is significant. Parsons has been involved with the technology since 1949 and has been responsible for developments such as the ammonia burning Claus and jointly with Unocal, the BSRP tail gas process and Selectox processes. Recent innovations in response changing environmental and production requirements have included catalytic and tail gas processes which reduce sulphur emissions. 6 figs., 2 tabs.

  19. Comparison of the SAWNUC model with CLOUD measurements of sulphuric acid-water nucleation

    CERN Document Server

    Ehrhart, Sebastian; Almeida, Joao; Amorim, Antonio; Barmet, Peter; Bianchi, Federico; Dommen, Josef; Dunne, Eimear M; Duplissy, Jonathan; Franchin, Alessandro; Kangasluoma, Juha; Kirkby, Jasper; Kürten, Andreas; Kupc, Agnieszka; Lehtipalo, Katrianne; Nieminen, Tuomo; Riccobono, Francesco; Rondo, Linda; Schobesberger, Siegfried; Steiner, Gerhard; Tomé, António; Wimmer, Daniela; Baltensperger, Urs; Wagner, Paul E; Curtius, Joachim

    2016-01-01

    Binary nucleation of sulphuric acid-water particles is expected to be an important process in the free troposphere at low temperatures. SAWNUC (Sulphuric Acid Water Nucleation) is a model of binary nucleation that is based on laboratory measurements of the binding energies of sulphuric acid and water in charged and neutral clusters. Predictions of SAWNUC are compared for the first time comprehensively with experimental binary nucleation data from the CLOUD chamber at European Organization for Nuclear Research. The experimental measurements span a temperature range of 208–292 K, sulphuric acid concentrations from 1·106 to 1·109 cm−3, and distinguish between ion-induced and neutral nucleation. Good agreement, within a factor of 5, is found between the experimental and modeled formation rates for ion-induced nucleation at 278 K and below and for neutral nucleation at 208 and 223 K. Differences at warm temperatures are attributed to ammonia contamination which was indicated by the presence of ammonia-sulphu...

  20. Sulphur in the metal poor globular cluster NGC 6397

    Science.gov (United States)

    Koch, A.; Caffau, E.

    2011-10-01

    Sulphur (S) is a non-refractory α-element that is not locked into dust grains in the interstellar medium. Thus no correction to the measured, interstellar sulphur abundance is needed and it can be readily compared to the S content in stellar photospheres. Here we present the first measurement of sulphur in the metal poor globular cluster (GC) NGC 6397, as detected in a MIKE/Magellan high signal-to-noise, high-resolution spectrum of one red giant star. While abundance ratios of sulphur are available for a larger number of Galactic stars down to an [Fe/H] of ~ -3.5 dex, no measurements in globular clusters more metal poor than -1.5 dex have been reported so far. We find aNLTE, 3-D abundance ratio of [S/Fe] = +0.52 ± 0.20 (stat.) ± 0.08 (sys.), based on theS I, Multiplet 1 line at 9212.8 Å. This value is consistent with a Galactic halo plateau as typical of other α-elements in GCs and field stars, but we cannot rule out its membership with a second branch of increasing [S/Fe] with decreasing [Fe/H], claimed in the literature, which leads to a large scatter at metallicities around - 2 dex. The [S/Mg] and [S/Ca] ratios in this star are compatible with a Solar value to within the (large) uncertainties. Despite the very large scatter in these ratios across Galactic stars between literature samples, this indicates that sulphur traces the chemical imprints of the other α-elements in metal poor GCs. Combined with its moderate sodium abundance ([S/Na]NLTE = 0.48), the [S/Fe] ratio in this GC extends a global, positive S-Na correlation that is not seen in field stars and might indicate that proton-capture reactions contributed to the production of sulphur in the (metal poor) early GC environments. This paper includes data gathered with the 6.5 m Magellan Telescopes located at Las Campanas Observatory, Chile.

  1. Impact of pedospheric and atmospheric sulphur nutrition on sulphur metabolism of Allium cepa L., a species with a potential sink capacity for secondary sulphur compounds

    NARCIS (Netherlands)

    Durenkamp, M.; De Kok, L.J.

    Onion (Afflum cepa L.) was able to use atmospheric H2S as sole sulphur source for growth. The foliarly absorbed H2S was rapidly metabolized into water-soluble, non-protein thiol compounds, including cysteine, and subsequently into other sulphur compounds in the shoots. In H2S-exposed plants, the

  2. Steam reforming of commercial ultra-low sulphur diesel

    Energy Technology Data Exchange (ETDEWEB)

    Boon, J.; Van Dijk, E.; De Munck, S.; Van den Brink, R. [Energy research Centre of The Netherlands, ECN Hydrogen and Clean Fossil Fuels, P.O. Box 1, NL1755ZG Petten (Netherlands)

    2011-03-11

    Two main routes for small-scale diesel steam reforming exist: low-temperature pre-reforming followed by well-established methane steam reforming on the one hand and direct steam reforming on the other hand. Tests with commercial catalysts and commercially obtained diesel fuels are presented for both processes. The fuels contained up to 6.5 ppmw sulphur and up to 4.5 vol.% of biomass-derived fatty acid methyl ester (FAME). Pre-reforming sulphur-free diesel at around 475C has been tested with a commercial nickel catalyst for 118 h without observing catalyst deactivation, at steam-to-carbon ratios as low as 2.6. Direct steam reforming at temperatures up to 800C has been tested with a commercial precious metal catalyst for a total of 1190 h with two catalyst batches at steam-to-carbon ratios as low as 2.5. Deactivation was neither observed with lower steam-to-carbon ratios nor for increasing sulphur concentration. The importance of good fuel evaporation and mixing for correct testing of catalysts is illustrated. Diesel containing biodiesel components resulted in poor spray quality, hence poor mixing and evaporation upstream, eventually causing decreasing catalyst performance. The feasibility of direct high temperature steam reforming of commercial low-sulphur diesel has been demonstrated.

  3. Steam reforming of commercial ultra-low sulphur diesel

    Science.gov (United States)

    Boon, Jurriaan; van Dijk, Eric; de Munck, Sander; van den Brink, Ruud

    Two main routes for small-scale diesel steam reforming exist: low-temperature pre-reforming followed by well-established methane steam reforming on the one hand and direct steam reforming on the other hand. Tests with commercial catalysts and commercially obtained diesel fuels are presented for both processes. The fuels contained up to 6.5 ppmw sulphur and up to 4.5 vol.% of biomass-derived fatty acid methyl ester (FAME). Pre-reforming sulphur-free diesel at around 475 °C has been tested with a commercial nickel catalyst for 118 h without observing catalyst deactivation, at steam-to-carbon ratios as low as 2.6. Direct steam reforming at temperatures up to 800 °C has been tested with a commercial precious metal catalyst for a total of 1190 h with two catalyst batches at steam-to-carbon ratios as low as 2.5. Deactivation was neither observed with lower steam-to-carbon ratios nor for increasing sulphur concentration. The importance of good fuel evaporation and mixing for correct testing of catalysts is illustrated. Diesel containing biodiesel components resulted in poor spray quality, hence poor mixing and evaporation upstream, eventually causing decreasing catalyst performance. The feasibility of direct high temperature steam reforming of commercial low-sulphur diesel has been demonstrated.

  4. Assessing the suitability of Norway spruce wood as an environmental archive for sulphur

    International Nuclear Information System (INIS)

    Barrelet, T.; Ulrich, A.; Rennenberg, H.; Zwicky, C.N.; Kraehenbuehl, U.

    2008-01-01

    The aim of this study was to assess the suitability of Norway spruces (Picea abies L. Karst.) as an environmental archive for sulphur. For this purpose spruce trees were sampled in two distinct regions of Switzerland: the Alps and the Swiss Plateau, which differ significantly with respect to S immission. Wood samples were measured using two methods: LASER Ablation high resolution inductively coupled plasma mass spectrometry (LA-HR-ICP-MS) and inductively coupled plasma optical emission spectrometry (ICP-OES) after acid digestion. Independently corroborated by previous measurements of sulphur in peat bogs, the rise and fall of sulphur dioxide pollution in Switzerland appears to be reflected in spruce wood sulphur content. While the wood sulphur content profile of trees sampled in the Alps is relatively flat, the profiles of trees located on the Swiss Plateau display a characteristic sulphur peak. This corresponds to air pollution data in the different regions and indicates that the trees reacted on the changing S supply and recorded a pollution signal in the wood. - Norway spruce is a suitable archive for sulphur when physiological aspects and limitations are taken into account

  5. Sulphur oxidising bacteria in mangrove ecosystem: A review ...

    African Journals Online (AJOL)

    Sulphur-oxidizing bacteria such as photoautotrophs, chemolithotrophs and heterotrophs play an important role in the mangrove environment for the oxidation of the toxic sulphide produced by sulphur reducing bacteria and act as a key driving force behind all sulphur transformations in the mangrove ecosystem which is ...

  6. K lines in the sulphur isonuclear sequence

    International Nuclear Information System (INIS)

    Palmeri, P.; Mendoza, C.; Bautista, M.A.; Garcia, J.; Kallman, T.R.

    2006-01-01

    Accurate and complete sets of atomic data are being computed for the radiative and Auger processes giving rise to K lines in ions of sulphur. AUTOSTRUCTURE, HFR and BPRM codes are used, taking into account configuration interaction, core relaxation and relativistic effects so as to generate data following an approach used in our previous studies on iron and oxygen. Level energies, wavelengths, A-values and Auger rates are compared with available measurements and previous calculations

  7. Regional modelling of anthropogenic sulphur in Southeast Asia

    Science.gov (United States)

    Engardt, M.; Leong, C. P.

    A co-operative research project between the Malaysian Meteorological Service (MMS) and the Swedish Meteorological and Hydrological Institute (SMHI) focussing on the usage of an atmospheric transport and chemistry model, has just been initiated. Here, we describe the main features of the dispersion model and discuss a first set of calculations in light of available measurements of sulphuric species in Southeast Asia. According to our results, anthropogenic sulphur concentrations and depositions are particularly high near the large cities of the region, around a metal smelter in the southern Philippines, and in a region extending from northern Vietnam into southeastern China. These areas coincide with the high-emissions regions of Southeast Asia and we tentatively conclude that regional transport of acidifying species is not as far-reaching as in the mid-latitudes. From our calculations, and from supporting measurements we conclude that most of rural Southeast Asia is not yet severely affected by anthropogenic sulphur, but given the rapid rate of economical development in this region the situation may deteriorate quickly. Areas that are particularly at risk include the large cities, northern Vietnam, most of central Thailand, most of peninsular Malaysia, eastern Sumatra and parts of Java, all of which receive total-sulphur depositions in excess of 0.5 g S m -2 yr -1. Our model simulates sulphate in precipitation in accordance with measurements, but it has a tendency to overestimate atmospheric SO 2. It remains to be investigated whether this is a problem in the model formulation or a result of unrepresentative sampling. An immediate continuation of this study should be performed with higher spatial resolution than the currently used 100×100 km 2. Other imperfections in this model study, which should be addressed in future work, include parameterised vertical transport in deep convective clouds, the influence of natural emissions (primarily from volcanoes) on the

  8. The fate of sulphur in the Cu-based Chemical Looping with Oxygen Uncoupling (CLOU) Process

    International Nuclear Information System (INIS)

    Adánez-Rubio, Iñaki; Abad, Alberto; Gayán, Pilar; García-Labiano, Francisco; Diego, Luis F. de; Adánez, Juan

    2014-01-01

    Highlights: • 15 h of CLOU experiments using lignite were carried out in a continuously unit. • The sulphur split between fuel- and air-reactor streams in the process was analysed. • Most of the sulphur introduced with the fuel exits as SO 2 at the fuel-reactor. • The use of a carbon separation system to reduce the S emission was evaluated. • Coals with high S content can be burnt in a CLOU process with a Cu-based material. - Abstract: The Chemical Looping with Oxygen Uncoupling (CLOU) process is a type of Chemical Looping Combustion (CLC) technology that allows the combustion of solid fuels with air, as with conventional combustion, through the use of oxygen carriers that release gaseous oxygen inside the fuel reactor. The aim of this work was to study the behaviour of the sulphur present in fuel during CLOU combustion. Experiments using lignite as fuel were carried out in a continuously operated 1.5 kW th CLOU unit during more than 15 h. Particles containing 60 wt.% CuO on MgAl 2 O 4 , prepared by spray drying, were used as the oxygen carrier in the CLOU process. The temperature in the fuel reactor varied between 900 and 935 °C. CO 2 capture, combustion efficiency and the sulphur split between fuel and air reactor streams in the process were analysed. Complete combustion of the fuel to CO 2 and H 2 O was found in all experiments. Most of the sulphur introduced with the fuel exited as SO 2 at the fuel reactor outlet, although a small amount of SO 2 was measured at the air reactor outlet. The SO 2 concentration in the air reactor exit flow decreased as the temperature in the fuel reactor increased. A carbon capture efficiency of 97.6% was achieved at 935 °C, with 87.9 wt.% of the total sulphur exiting as SO 2 in the fuel reactor. Both the reactivity and oxygen transport capacity of the oxygen carrier were unaffected during operation with a high sulphur content fuel, and agglomeration problems did not occur. Predictions were calculated regarding the use

  9. Simultaneous analyses of gaseous and particulate sulphur compounds in the atmosphere by x-ray fluorescence spectrometry, (1)

    International Nuclear Information System (INIS)

    Matsuda, Yatsuka; Mamuro, Tetsuo

    1974-01-01

    An analytical technique for the simultaneous measurements of the atmospheric concentrations of SO 2 gas and sulphur absorbed by aerosol particles has been developed. Aerosol particles are collected on membrane filter and at the same time SO 2 gas is captured on alkali impregnated filter. The sulphur content in each filter is measured by an energy dispersive X-ray fluorescence spectrometer consisting of a Si(Li) semiconductor detector connected to a multichannel pulse hight analyzer and an excitation source of 55 Fe. Two methods are acceptable for the determination of the sulphur content in impregnated filter by X-ray fluorescence analysis. In the first method X-ray fluorescence analysis is made after the collected sulphur has diffused and distributed uniformly enough throughout filter, and in the second method X-ray fluorescence analysis has to be finished before the diffusion of the collected sulphur becomes appreciable. (auth.)

  10. Vapor mercury uptake with sulphur impregnated active carbons derived using sulphur dioxide

    International Nuclear Information System (INIS)

    Tong, S.; Methta, H.; Ahmed, I.; Morris, E.; Fuentes de Maria, L.; Jia, C.Q.

    2008-01-01

    Active carbon adsorption is the primary technology used for removal of vapour mercury from flue gases in coal-fired power plants, municipal solid waste combustors, and other sources. It can be carried out using two different processes, notably injection of powder active carbon into flue gas streams upstream of the particulate collection devices, and filtration with a granular active carbon fixed bed downstream of the flue gas desulphurization units and/or particulate collectors. This paper presented an investigation of vapour mercury uptake performance of laboratory-made sulphur impregnated active carbons (SIACs) using a fixed bed reactor in a temperature range of 25 to 200 degrees Celsius. The materials and methods as well as the properties of activated carbons studied were presented. The experimental set-up was also described. The paper discussed the effects of initial concentration, the flow rate, the loading amount of SIACs, temperature, and the sulphur impregnation on the mercury uptake performance. The study showed that SIACs produced with sulphur dioxide exhibited a more complicated behaviour when temperature was varied, implying a mixed adsorption mechanism. 10 refs., 3 tabs., 8 figs

  11. The useful application of sulphur-bound waste materials

    NARCIS (Netherlands)

    Alkemade, M.M.C.; Koene, J.I.A.

    1996-01-01

    An immobilization process is described which is based on sulphur (instead of cement) as a binding agent for the treatment of hazardous waste materials. Elemental sulphur is able to bind chemically metals such as mercury and, to a lesser extent, lead as metal sulphides. Furthermore, sulphur forms a

  12. Utilization of activated carbon loaded with sulphur for sulphur fertilization in agriculture; Verwertung von mit Schwefel beladener Aktivkohle als Schwefelduenger in der Landwirtschaft

    Energy Technology Data Exchange (ETDEWEB)

    Kirfel, Kristina; Hoffmann, Heide [Humboldt Univ. Berlin (Germany). AG Agraroekologie und Oekologischer Landbau

    2013-01-15

    Due to the decrease of atmospheric sulphur deposition, sulphur fertilization has gained significance for agriculture in recent years. Carbon-sulphur-pellets (CSP), activated carbon pellets loaded with sulphur, previously used for desulphurization in biogas plants, are up to now disposed of as waste. In this context the question arises if CSP could be of use for sulphur fertilization of agricultural crops. The objective of this study was to test sulphur release and plant availability from, and plant tolerance towards CSP. A pot experiment using Zea mays with different shares of CSP was carried out. Leaf green intensity of vital plants, indicating plants' current nutritional status, was measured and differences in plant development were documented regularly. At the end of the trial period biomass and elemental contents of the test plants, as well as electrical conductivity and pH-value of the substrate-CSP-mixtures were determined. Amendments of 0.2 m.-% to 1.0 m.-% had a positive effect on plants' dry mass yield; higher shares led to considerable yield losses. By addition of CSP, sulphur content in the plant dry mass increased compared to the control without sulphur fertilization. This result indicates that sulphur adsorbed to activated carbon becomes plant available when applicated to cultural substrate. (orig.)

  13. Preparation and characterization compatible pellets for immobilization of colloidal sulphur nanoparticles

    Science.gov (United States)

    Adlim, M.; Zarlaida, F.; Khaldun, I.; Dewi, R.; Jamilah, M.

    2018-03-01

    Mercury pollution in atmosphere is dominated by mercury vapour release from coal burning and gold-amalgam separation in gold mining. The initial steps in formulating a compatible mercury absorbent for mercury stabilization was fabrication of pellet supported colloidal sulphur. Sulphur is used to stabilize mercury vapour by formation of metacinnabar that has much lower toxicity. The sulphur reactivity toward mercury vapour can be enhanced by using colloidal sulphur nanoparticles immobilized on compatible pellets. Clay pellets would have heat resistance but in fact, they were less stable in aqueous solution although their stability increased with inclusion of rice husk ash and sawdust or pineapple leaf fibre in the composite. Pellets made of rice husk ash and polyvinyl acetate were stable in water at least for 24 hours. Sulphur from thiosulfate precursor that immobilized onto surface of pellet using chitosan as the stabilizer and the binding agent gave lower sulphur content compared to sulphur from other precursors (sulphur powder and sulphur-CS2). Sulphur from thiosulfate precursor was in form of colloid, has nanosize, and disperse particles on the surface of rice husk ash pellets. Sulphur immobilization methods affect on sulphur particles exposure on the pellet surface.

  14. High pressure treatments accelerate changes in volatile composition of sulphur dioxide-free wine during bottle storage.

    Science.gov (United States)

    Santos, Mickael C; Nunes, Cláudia; Rocha, M Angélica M; Rodrigues, Ana; Rocha, Sílvia M; Saraiva, Jorge A; Coimbra, Manuel A

    2015-12-01

    The impact of high hydrostatic pressure (HHP) treatments on volatile composition of sulphur dioxide-free wines during bottle storage was studied. For this purpose, white and red wines were produced without sulphur dioxide (SO2) and, at the end of the alcoholic fermentation, the wines were pressurised at 500 MPa and 425 MPa for 5 min. Wine with 40 ppm of SO2 and a wine without a preservation treatment were used as controls. More than 160 volatile compounds, distributed over 12 chemical groups, were identified in the wines by an advanced gas chromatography technique. The pressurised wines contained a higher content of furans, aldehydes, ketones, and acetals, compared with unpressurised wines after 9 months of storage. The changes in the volatile composition indicate that HHP treatments accelerated the Maillard reaction, and alcohol and fatty acid oxidation, leading to wines with a volatile composition similar to those of faster aged and/or thermally treated wines. Copyright © 2015 Elsevier Ltd. All rights reserved.

  15. Sulphur isotope variations in the atmosphere

    International Nuclear Information System (INIS)

    Newman, L.; Krouse, H.R.; Grinenko, V.A.

    1991-01-01

    The measurement of the isotope ratios of sulphur and oxygen can in principal be used to assess sulphur inputs into, transformation within, and removal from the atmosphere. Major inputs arise from both anthropogenic and biogenic activities. Transformations arise from oxidation, neutralization, and other chemical reactions. Advection causes dilution and the main removal processes are dry deposition (governed by gravitation and diffusion) and rain. The admixture of sources can be discerned from their isotopic signatures whereas transformations and removal can be followed from the isotopic fractionation that might occur. In this chapter, the atmospheric sulphur cycle and the associated chemistry are summarized. Also presented is information on natural isotopic variations and fundamental concepts relating to the use of isotopic data to delineate anthropogenic S in the atmosphere. Examples of successful applications of these concepts are given. Finally, consideration is given to the potential of using isotopically enriched sulphur to study transport and transformation of atmospheric S compounds. Refs, figs and tabs

  16. Potential to reduce emissions of sulphur dioxide through reducing sulphur levels in heavy and light fuel oils - a discussion paper

    International Nuclear Information System (INIS)

    Tushingham, M.; Bellamy, J.

    2001-01-01

    Background information on the sulphur levels in light fuel oil (used in residential heating) and heavy fuel oil (used as industrial fuel oil) is provided. In addition to the description of sulphur levels in light and heavy fuel oils, the report also provides a summary of regulatory limits in Canada and elsewhere, and a description of the emission benefits of decreasing sulphur in fuels. 4 refs., 10 tabs., 12 figs

  17. Source of sulphur in the Ebro Basin (Northern Spain). Tertiary nonmarine evaporite deposits as evidenced by sulphur isotopes

    International Nuclear Information System (INIS)

    Birnbaum, S.J.; Coleman, D.

    1979-01-01

    The Ebro Basin is an intermontane basin, located in northern Spain, filled with Tertiary (largely Oligocene and Miocene) elastic and chemical deposits. Sulphur isotopes are utilized to determine the source of sulphur in the sulphate deposits (predominantly gypsum with accessory thenardite, mirabolite and epsomite). Data obtained from Tertiary gypsum rocks produce a range of delta 34 S values from +9.16% to + 14.02% with a mean of +13.61%. Data obtained from Triassic gypsum rocks (in source area) produce a range from +13.73% to +15.14%, with a mean of +14.66%. Values for Tertiary marine water range from +18% to +24%. These data indicate a nonmarine origin for sulpur within the Tertiary sulphate rocks. The contribution of Triassic sulphur to the groundwater system, plus varying degrees of dilution by isotopically lighter (atmospheric and sulphide) sulphur, best explains the isotopic ratios observed in the Tertiary Basin deposits. (Auth.)

  18. Development of the floating sulphur biofilm reactor for sulphide ...

    African Journals Online (AJOL)

    Development of the floating sulphur biofilm reactor for sulphide oxidation in biological water treatment systems. ... The effect of influent sulphide concentrations, flow rate and reactor dimensions on the sulphur biofilm formation were investigated for the optimisation of elemental sulphur recovery and sulphide removal ...

  19. Distribution of sulphur and trace elements in peat. [Literature survey with some additional sulphur analyses

    Energy Technology Data Exchange (ETDEWEB)

    Huttunen, S; Karhu, M

    1981-01-01

    A survey on the literature and contemporary research was made on peat sulphur and trace element studies. Marked variance between different peatlands and peat types has been noted. The available information is still inadequate for generalizations or statistical analysis mainly due to methodological variations and temporal and spatial variations in results. At the moment, the criteria applied in peatland inventories and evaluations are inadequate with respect to peat quality determinations. To some extent the quality of fuel peat should be determined in a mire inventory prior to peatland utilization. The areas over sulphide clay and some sulphate depositions may considerably increase the peat sulphur content. A proposal has been made to include the sulphur content monitoring in the cases where it exceeds 0.3 per cent. The trace elements may also bring about an increase in peat emissions if the deepest peat layers or polluted layers are burnt. The most important elements in this respect are Al, Fe, Mn, Pb, Zn, V, Ni, Hg, Cu, Cr, as well as As and U. The first ten because of the relatively high concentrations and last two because of pollution or toxocity and ore deposit factors. The peat hydrogen ion concentration has a positive correlation with copper and vanadium. The correlation is positive with the cobalt and nickel contents when the pH is low, and negative at a higher pH. A general peat type correlation shows maximum trace element contents in basal Carex peats with subsoil effects. The peat ash content and the Ti, Pb, V, Cr, Ni and S contents have positive correlations.

  20. Comparative study on sulphur reduction from heavy petroleum - Solvent extraction and microwave irradiation approach

    Energy Technology Data Exchange (ETDEWEB)

    Mohammed, Abdullahi Dyadya; Isah, Abubakar Garba; Umaru, Musa; Ahmed, Shehu [Department of Chemical Engineering, Federal University of Technology, P.M.B 65, Minna (Nigeria); Abdullahi, Yababa Nma [National Petroleum Investment Management Services (Nigeria National Petroleum Corporation), Lagos (Nigeria)

    2012-07-01

    Sulphur- containing compounds in heavy crude oils are undesirable in refining process as they affect the quality of the final product, cause catalyst poisoning and deactivation in catalytic converters as well as causing corrosion problems in oil pipelines, pumps and refining equipment aside environmental pollution from their combustion and high processing cost. Sulphur reduction has being studied using microwave irradiation set at 300W for 10 and 15minutes and oxidative- solvent extraction method using n- heptane and methanol by 1:1, 1:2 and 1:3 crude- solvent ratios after being oxidized with hydrogen peroxide, H2O2 oxidants. Percentage sulphur removal with n- heptane solvent by 1:1 and 1:2 are 81.73 and 85.47%; but extraction using methanol by different observed ratios gave less sulphur reduction. Indeed when microwave irradiated at 300W for 10 and 15minutes, 53.68 and 78.45% reduction were achieved. This indicates that microwave irradiation had caused oxidation by air in the oven cavity and results to formation of alkyl radicals and sulphoxide from sulphur compound in the petroleum. The prevailing sulphur found in the crude going by FT-IR results is sulphides which oxidized to sulphoxide or sulphones. It is clear that sulphur extraction with heptane is more efficient than microwave irradiation but economically due to demands for solvent and its industrial usage microwave irradiation can serve as alternative substitute for sulphur reduction in petroleum. Sulphur reduction by microwave radiation should be up- scaled from laboratory to a pilot plant without involving extraction column in the refining.

  1. Impurity photovoltaic effect in silicon solar cell doped with sulphur: A numerical simulation

    International Nuclear Information System (INIS)

    Azzouzi, Ghania; Chegaar, Mohamed

    2011-01-01

    The impurity photovoltaic effect (IPV) has mostly been studied in various semiconductors such as silicon, silicon carbide and GaAs in order to increase infrared absorption and hence cell efficiency. In this work, sulphur is used as the IPV effect impurity incorporated in silicon solar cells. For our simulation we use the numerical device simulator (SCAPS). We calculate the solar cell performances (short circuit current density J sc , open circuit voltage V oc , conversion efficiency η and quantum efficiency QE). We study the influence of light trapping and certain impurity parameters like impurity concentration and position in the gap on the solar cell performances. Simulation results for IPV effect on silicon doped with sulphur show an improvement of the short circuit current and the efficiency for sulphur energy levels located far from the middle of the band gap especially at E c -E t =0.18 eV.

  2. How sulphur was dislodged to sustain plant operation

    International Nuclear Information System (INIS)

    Verma, A.N.; Agarwal, A.K.

    1997-01-01

    Heavy Water Plant (Kota) employs chemical exchange between water and hydrogen sulphide gas. Formation of sulphur is a known phenomena during production of heavy water in G.S. process plants. It is observed that after three years of plant operation this sulphur is enough to choke the cold tower trays causing flooding of exchange towers and resultant decrease in throughput. G.S. process plants normally go for major turn around once in four years when sulphur is either manually cleaned or removed by steam wash after hydrogen sulphide gas has been removed from the system and towers have been fully decontaminated. As throughput starts decreasing after third year and plant operation becomes more difficult in fourth year, HWP (Kota) had evolved a procedure of heating the towers for dislodging sulphur from sieve trays when plant is running. With these procedures plant operation could be sustained without tower floodings even in fourth year, before plant could go for major turn around for manual removal of sulphur

  3. Organic sulphur in macromolecular sedimentary organic matter. II. Analysis of distributions of sulphur-containing pyrolysis products using multivariate techniques

    NARCIS (Netherlands)

    Sinninghe Damsté, J.S.; Eglinton, T.I.; Pool, W.; Leeuw, J.W. de; Eijkel, G.; Boon, J.J.

    1992-01-01

    This study describes the analysis of sulphur-containing products from Curie-point pyrolysis (Py) of eighty-five samples (kerogens, bitumen, and petroleum asphaltenes and coals) using gas chromatography (GC) in combination with sulphur-selective detection. Peak areas of approximately forty individual

  4. The mechanism of photosystem-II inactivation during sulphur deprivation-induced H2 production in Chlamydomonas reinhardtii.

    Science.gov (United States)

    Nagy, Valéria; Vidal-Meireles, André; Podmaniczki, Anna; Szentmihályi, Klára; Rákhely, Gábor; Zsigmond, Laura; Kovács, László; Tóth, Szilvia Z

    2018-05-01

    Sulphur limitation may restrain cell growth and viability. In the green alga Chlamydomonas reinhardtii, sulphur limitation may induce H 2 production lasting for several days, which can be exploited as a renewable energy source. Sulphur limitation causes a large number of physiological changes, including the inactivation of photosystem II (PSII), leading to the establishment of hypoxia, essential for the increase in hydrogenase expression and activity. The inactivation of PSII has long been assumed to be caused by the sulphur-limited turnover of its reaction center protein PsbA. Here we reinvestigated this issue in detail and show that: (i) upon transferring Chlamydomonas cells to sulphur-free media, the cellular sulphur content decreases only by about 25%; (ii) as demonstrated by lincomycin treatments, PsbA has a significant turnover, and other photosynthetic subunits, namely RbcL and CP43, are degraded more rapidly than PsbA. On the other hand, sulphur limitation imposes oxidative stress early on, most probably involving the formation of singlet oxygen in PSII, which leads to an increase in the expression of GDP-L-galactose phosphorylase, playing an essential role in ascorbate biosynthesis. When accumulated to the millimolar concentration range, ascorbate may inactivate the oxygen-evolving complex and provide electrons to PSII, albeit at a low rate. In the absence of a functional donor side and sufficient electron transport, PSII reaction centers are inactivated and degraded. We therefore demonstrate that the inactivation of PSII is a complex and multistep process, which may serve to mitigate the damaging effects of sulphur limitation. © 2018 The Authors The Plant Journal © 2018 John Wiley & Sons Ltd.

  5. Effect of Sulphur Fertilization on Grain Quality and Protein Composition of Durum Wheat (Triticum durum Desf.

    Directory of Open Access Journals (Sweden)

    Marianna Pompa

    2009-12-01

    Full Text Available The reduction of atmosphere emission of SO2 and the massive use of fertilizers high in nitrogen and phosphorus resulted in a decrease of the sulphur content in the soil. In durum wheat cultivation, sulphur supply plays a key role not only for plant growth, but also for grain quality. Sulphur is an essential macronutrient primarily used to synthesize methionine and cysteine and it is also involved in establishing protein structures by disulphide bonds. The aim of this study was to evaluate the effect of sulphur nutrition on grain quality and protein composition of durum wheat cultivars grown under water deficit conditions, typical of Mediterranean areas. To this purpose, in the 2003-2004 and 2004-2005 crop seasons a field trial was carried out by comparing two water regimes (irrigated and rainfed, two sulphur fertilizer levels and two durum wheat cultivars. Under our experimental conditions, an increase in protein and gluten content in the rainfed treatment and a positive effect of sulphur fertilization on quality parameters were observed. Few changes were observed in protein composition in response to sulphur fertilization.

  6. Two stage fluid bed-plasma gasification process for solid waste valorisation: Technical review and preliminary thermodynamic modelling of sulphur emissions

    International Nuclear Information System (INIS)

    Morrin, Shane; Lettieri, Paola; Chapman, Chris; Mazzei, Luca

    2012-01-01

    Highlights: ► We investigate sulphur during MSW gasification within a fluid bed-plasma process. ► We review the literature on the feed, sulphur and process principles therein. ► The need for research in this area was identified. ► We perform thermodynamic modelling of the fluid bed stage. ► Initial findings indicate the prominence of solid phase sulphur. - Abstract: Gasification of solid waste for energy has significant potential given an abundant feed supply and strong policy drivers. Nonetheless, significant ambiguities in the knowledge base are apparent. Consequently this study investigates sulphur mechanisms within a novel two stage fluid bed-plasma gasification process. This paper includes a detailed review of gasification and plasma fundamentals in relation to the specific process, along with insight on MSW based feedstock properties and sulphur pollutant therein. As a first step to understanding sulphur partitioning and speciation within the process, thermodynamic modelling of the fluid bed stage has been performed. Preliminary findings, supported by plant experience, indicate the prominence of solid phase sulphur species (as opposed to H 2 S) – Na and K based species in particular. Work is underway to further investigate and validate this.

  7. Development of a Linear Flow Channel Reactor for sulphur removal ...

    African Journals Online (AJOL)

    2013-09-23

    Sep 23, 2013 ... gation of sulphur production in floating sulphur biofilms as a means for addressing this problem. These 50 µm ... Preliminary studies on the use of the FSB system for sulphur removal in Integrated Managed Passive Treatment ...

  8. Distribution of sulphur into products from waste tire pyrolysis

    International Nuclear Information System (INIS)

    Susa, D.; Haydary, J.; Markos, J.

    2012-01-01

    Tire pyrolysis is getting growing attention as an effective waste tire disposal method in comparison to environmentally less friendly methods like dumping or incineration. But the scrap tire sulphur content can be a potential obstacle to scrap tire utilization as a fuel. In this paper the distribution of sulphur into tire pyrolysis yields, solid (char) and liquid (tar), was investigated. The pyrolysis experiments were carried out under different conditions to determine the partitioning of sulphur into pyrolysis products. The influence of different temperatures and reaction times was investigated in a laboratory flow reactor under nitrogen atmosphere. Solid and liquid residues were collected and analyzed by elemental analysis. The sulphur content in residual char and tar was determined using an elemental analyzer and the sulphur forms in tar were characterized by the X-ray photoelectron spectroscopy (XPS). (Authors)

  9. Optimal sulphuric acid production using Acidithiobacillus caldus ...

    African Journals Online (AJOL)

    AFRICAN JOURNALS ONLINE (AJOL) · Journals · Advanced Search · USING ... oxygen uptake rate of 1.35 g/L.day (OUR), 52% sulphur conversion at a rate of 0.83 ... achieving a sulphuric acid production rate of 2.76 g/L.day (dP/dt), while the ...

  10. Discontinuities in Jovian sulphur plasma

    Energy Technology Data Exchange (ETDEWEB)

    Mekler, Y [Jet Propulsion Lab., Pasadena, CA (USA); Eviatar, A; Siscoe, G L

    1979-10-01

    In recent years, the Jovian sulphur nebula, which is the only component of the thermal plasma in the magnetosphere of Jupiter which emits in the visible, has been the subject of considerable study. A large number of investigators have come up with widely differing models for the density, composition and temperature of the Jovian magnetospheric plasma. In this paper a different characteristic of the sulphur emission, namely its radial distribution is discussed and an attempt is made to assess its implications for the plasma and magnetic field configuration of the inner magnetosphere of Jupiter.

  11. Comparison of methods for the determination of reduced inorganic sulphur in acid sulphate soils

    International Nuclear Information System (INIS)

    Santomartino, S.L.

    1999-01-01

    Full text: The management of acid sulphate soils requires analytical methods that provide accurate data on the quantity of reduced inorganic sulphur within a soil, as it is this fraction that produces acid upon oxidation. This study uses sulphidic Coode Island Silt samples to compare common analytical methods including POCAS (Peroxide Oxidation-Combined Acidity and Sulphate) which consists of TSA (Total Sulphidic Acidity), S pos (Peroxide Oxidisable Sulphur), TOS (Total Oxidisable Sulphur) and chromium-reducible sulphur. The determination of total sulphur by Leco sulphur is strongly correlated with, but slightly less than, that analysed by XRF. Comparison of soil sulphide content by chromium-reducible sulphur, TSA and TOS methods indicates that TOS values are substantially higher than both other methods. The problem with the TOS method lies in the sulphate extraction procedure. Hot distilled water and HCI are commonly used as extractants, however hot distilled water fails to remove organic sulphur, thereby overestimating the sulphide content of the soil. Leco carbon analyses verify that a substantial proportion of organic matter exists within the samples. The HCI extraction process, which uses Ion Chromatography to analyse for sulphate, produces highly inaccurate results due to the interference of the sulphate peak by the chloride peak during analysis. An alternative method involving HCI extraction and XRF analysis of the soil residue is currently being undertaken. The use of KCI to extract sulphate generally produces values similar to the hot distilled water method. The sulphidic content measured by TSA is strongly correlated with, but slightly higher than that determined by the chromium-reducible sulphur method. This is attributed to the use of hydrogen peroxide in the TSA method, which oxidises organic matter to organic acids in addition to oxidising sulphides. These preliminary findings indicate that the chromium-reducible sulphur method is the most suitable

  12. Sulphur oxidising bacteria in mangrove ecosystem: A review

    African Journals Online (AJOL)

    SAM

    2014-07-16

    Jul 16, 2014 ... factors such as salinity and nutrient availability highly variable. Mangrove .... sulphate and converts it into organic sulphur compound. (Subba Rao ..... of organic fertilizer long favored in Australia. .... Fish. Technol. Soc. 21:126-130. Dias ACF, Andreote FD, Rigonato J, Fiore MF, Melo IS, Araujo WL. (2010).

  13. Sulphur self–retention and sulphur dioxide capture with active calcium minerals in mineral–rich coals / Mchabe, D.

    OpenAIRE

    Mchabe, Dursman

    2011-01-01

    In order to provide information for the development of clean coal technology, the sulphur self–retention and sulphur dioxide capturing properties of minerals present in low grade coals was investigated. This study consisted of detailed mineral analyses of coal and ash samples using results obtained from QEMSCAN and separate retention (coal) and capture (ash) experiments with laboratory scale reactors. Typical South African coal samples were used in this study. The ash content v...

  14. Muon transfer to sulphur dioxide

    International Nuclear Information System (INIS)

    Mulhauser, F.; Schneuwly, H.

    1993-01-01

    A systematic study of muon capture and muon transfer has been performed in seven different H 2 + SO 2 gas mixtures. From the single-exponential time structure of the muonic sulphur x-rays, one determines the lifetime of the μp atoms under the given experimental conditions. The reduced muon transfer rates to the sulphur dioxide molecule, deduced from these lifetimes, all agree well with each other. The muonic oxygen time spectra show an additional structure as if μp atoms of another kind were present. Comparable time structures are observed in a D 2 + SO 2 mixture. (author)

  15. Distribution of sulphur and trace elements in peat. A literature survey with some additional sulphur analyses

    Energy Technology Data Exchange (ETDEWEB)

    Huttunen, S; Karhu, M

    1981-01-01

    A survey on the literature and contemporary research was made on peat sulphur and trace element studies. Marked variance between different peatlands and peat types has been noted. The available information is still inadequate for generalizations or statistical analysis mainly due to methodological variations and temporal and spatial variations in results. At the moment, the criteria applied in peatland inventories and evaluations are inadequate with respect to peat quality determinations. To some extent the quality of fuel peat should be determined in a mire inventory prior to peatland utilization. The areas over sulphide clay and some sulphate depositions may considerably increase the peat sulphur content. A proposal has been made to include the sulphur content monitoring in the cases where it exceeds 0.3 per cent. The trace elements may also bring about an increase in peat emissions if the deepest peat layers or polluted layers are burnt. The most important elements in this respect are Al, Fe, Mn, Pb, Zn, V, Ni, Hg, Cu, Cr, as well as As and U. The first ten because of the relatively high concentrations and last two because of pollution or toxocity and ore deposit factors. The peat hydrogen ion concentration has a positive correlation with copper and vanadium. The correlation is positive with the cobalt and nickel contents when the pH is low, and negative at a higher pH. A general peat type correlation shows maximum trace element contents in basal Carex peats with subsoil effects. The peat ash content and the Ti, Pb, V, Cr, Ni, and S contents have positive correlations. (Refs. 290).

  16. Availability and uptake of sulphur by mustard in three soils in Udaipur valley

    International Nuclear Information System (INIS)

    Kataria, S.K.; Shriniwas

    1976-01-01

    The differential behaviour of three soils (Bargaon, Bhatewar red and Bhatewar black) for availability of sulphur to mustard was studied in a greenhouse pot culture experiment using five doses of sulphur (0,20,40,80,120 ppm) applied as 35 S tagged ammonium sulphate. Application of sulphur significantly increased the dry matter of mustard over control, however, maximum dry matter was obtained when sulphur was applied at 40 ppm level, thereafter, any higher doses did not prove beneficial. Sulphur content in the plant tissue and percent of sulphur in the plant derived from fertilizer increased with successive doses of applied sulphur. (author)

  17. Integrated laboratory scale demonstration experiment of the hybrid sulphur cycle and preliminary scale-up

    International Nuclear Information System (INIS)

    Leybros, J.; Rivalier, P.; Saturnin, A.; Charton, S.

    2010-01-01

    The hybrid sulphur cycle is today one of the most promising processes to produce hydrogen on a massive scale within the scope of high temperature nuclear reactors development. Thus, the Fuel Cycle Technology Department at CEA Marcoule is involved in studying the hybrid sulphur process from a technical and economical performance standpoint. Based on mass and energy balance calculations, a ProsimPlus TM flow sheet and a commercial plant design were prepared. This work includes a study on sizing of the main equipment. The capital cost has been estimated using the major characteristics of main equipment based upon formulae and charts published in literature. A specific approach has been developed for electrolysers. Operational costs are also proposed for a plant producing 1000 mol/s H 2 . Bench scale and pilot experiments must focus on the electrochemical step due to limited experimental data. Thus, a pilot plant with a hydrogen capacity of 100 NL/h was built with the aim of acquiring technical and technological data for electrolysis. This pilot plant was designed to cover a wide range of operating conditions: sulphuric acid concentrations up to 60 wt.%, temperatures up to 100 deg. C and pressures up to 10 bar. New materials and structures recently developed for fuel cells, which are expected to yield significant performance improvements when applied to classical electrochemical processes, will be tested. All experiments will be coupled with phenomenological simulation tools developed jointly with the experimental programme. (authors)

  18. Molecular understanding of sulphuric acid-amine particle nucleation in the atmosphere.

    Science.gov (United States)

    Almeida, João; Schobesberger, Siegfried; Kürten, Andreas; Ortega, Ismael K; Kupiainen-Määttä, Oona; Praplan, Arnaud P; Adamov, Alexey; Amorim, Antonio; Bianchi, Federico; Breitenlechner, Martin; David, André; Dommen, Josef; Donahue, Neil M; Downard, Andrew; Dunne, Eimear; Duplissy, Jonathan; Ehrhart, Sebastian; Flagan, Richard C; Franchin, Alessandro; Guida, Roberto; Hakala, Jani; Hansel, Armin; Heinritzi, Martin; Henschel, Henning; Jokinen, Tuija; Junninen, Heikki; Kajos, Maija; Kangasluoma, Juha; Keskinen, Helmi; Kupc, Agnieszka; Kurtén, Theo; Kvashin, Alexander N; Laaksonen, Ari; Lehtipalo, Katrianne; Leiminger, Markus; Leppä, Johannes; Loukonen, Ville; Makhmutov, Vladimir; Mathot, Serge; McGrath, Matthew J; Nieminen, Tuomo; Olenius, Tinja; Onnela, Antti; Petäjä, Tuukka; Riccobono, Francesco; Riipinen, Ilona; Rissanen, Matti; Rondo, Linda; Ruuskanen, Taina; Santos, Filipe D; Sarnela, Nina; Schallhart, Simon; Schnitzhofer, Ralf; Seinfeld, John H; Simon, Mario; Sipilä, Mikko; Stozhkov, Yuri; Stratmann, Frank; Tomé, Antonio; Tröstl, Jasmin; Tsagkogeorgas, Georgios; Vaattovaara, Petri; Viisanen, Yrjo; Virtanen, Annele; Vrtala, Aron; Wagner, Paul E; Weingartner, Ernest; Wex, Heike; Williamson, Christina; Wimmer, Daniela; Ye, Penglin; Yli-Juuti, Taina; Carslaw, Kenneth S; Kulmala, Markku; Curtius, Joachim; Baltensperger, Urs; Worsnop, Douglas R; Vehkamäki, Hanna; Kirkby, Jasper

    2013-10-17

    Nucleation of aerosol particles from trace atmospheric vapours is thought to provide up to half of global cloud condensation nuclei. Aerosols can cause a net cooling of climate by scattering sunlight and by leading to smaller but more numerous cloud droplets, which makes clouds brighter and extends their lifetimes. Atmospheric aerosols derived from human activities are thought to have compensated for a large fraction of the warming caused by greenhouse gases. However, despite its importance for climate, atmospheric nucleation is poorly understood. Recently, it has been shown that sulphuric acid and ammonia cannot explain particle formation rates observed in the lower atmosphere. It is thought that amines may enhance nucleation, but until now there has been no direct evidence for amine ternary nucleation under atmospheric conditions. Here we use the CLOUD (Cosmics Leaving OUtdoor Droplets) chamber at CERN and find that dimethylamine above three parts per trillion by volume can enhance particle formation rates more than 1,000-fold compared with ammonia, sufficient to account for the particle formation rates observed in the atmosphere. Molecular analysis of the clusters reveals that the faster nucleation is explained by a base-stabilization mechanism involving acid-amine pairs, which strongly decrease evaporation. The ion-induced contribution is generally small, reflecting the high stability of sulphuric acid-dimethylamine clusters and indicating that galactic cosmic rays exert only a small influence on their formation, except at low overall formation rates. Our experimental measurements are well reproduced by a dynamical model based on quantum chemical calculations of binding energies of molecular clusters, without any fitted parameters. These results show that, in regions of the atmosphere near amine sources, both amines and sulphur dioxide should be considered when assessing the impact of anthropogenic activities on particle formation.

  19. Effect of sulphur on the strengthening of a Zr-Nb alloy

    International Nuclear Information System (INIS)

    Chang, K.I.; Hong, S.I.

    2008-01-01

    The effect of sulphur on the strengthening and the thermally activated deformation of cold-worked Zr-1 Nb alloy was investigated. In the present study, the sulphur strengthening was observed even at room temperature unlike the previous study of Ferrer et al. The flow stress increased by 65 MPa at room temperature with the addition of sulphur as little as 20 ppm. With further increase of sulphur content up to 300 ppm, negligible change of the flow stress was observed. The additive strengthening behavior in which the entire stress-strain curve shift upward by the friction stress due to the addition of sulphur was observed in the Zr-Nb alloy of the present study. The activation volume decreased slightly (from 110b 3 to 80b 3 ) with the addition of 300 ppm sulphur at room temperature. The rate-controlling mechanism of the deformation can best be explained by the dislocation interaction mechanism in which the segregation of alloying elements such as oxygen and sulphur atoms affects the activation length of dislocations

  20. Modified sulphur cement: A low porosity encapsulation material for low, medium and alpha waste

    International Nuclear Information System (INIS)

    Dalen, A. van; Rijpkema, J.E.

    1989-01-01

    Modified sulphur cement, available under the trade name Chement 2000, is a thermoplastic candidate material for the matrix of low, intermediate and alpha radioactive waste. The main source of sulphur is the desulphurization of fossil fuels. In view of the future increase of this product a modified compound of sulphur has been developed at the US Bureau of Mines. Modified sulphur cement as matrix material has properties in common with Portland or blast furnace cement and bitumen. The mechanical strength is comparable to hydraulic cement products. The process to incorporate waste materials is identical to bitumization. The leachability and the resistance to attack by chemicals is nearly the same as for bituminized products. This study showed also that the radiation resistance is high without radiolytic gas production and without change in dimensions (swelling). The rigidity of the matrix is a disadvantage when internal pressures are built up. The thermal conductivity and the heat of combustion of sulphur is low resulting in slow damage to the waste form under fire conditions, even when the temperature of self ignition in air is 220 0 C. The low leachability, the very slow effective diffusion of H 2 O and HTO, and the low permeability is due to the small pore diameters in the modified sulphur matrix. The loading capacity of modified sulphur cement depends on grain size and distribution and is for ungraded ashes, precipitates, dried sludges, etc., in the order of 40-50% of weight. The price of Chement 2000 per tonne is equal to those of blown bitumen

  1. The certification of the contents (mass fractions) of sulphur in six coals

    Energy Technology Data Exchange (ETDEWEB)

    Griepink, B; Maier, E A; Wilkinson, H C [CEC, Bruxelles (Belgium)

    1990-01-01

    This report presents the preparation and the certification of the sulphur content of six coal reference materials: low volatile steam coal (CRM 331), high volatile industrial coal (CRM 332), coking steam coal (CRM 333), anthracite (CRM 334), flame coal (CRM 335) and high volatile steam coal (CRM 336), as well as the homogeneity and stability studies. The analytical work leading to certification is also presented. The certified mass fractions for total sulphur in CRMs 331, 332, 333, 334, 335 and 336 respectively are 4.99 mg/g, 9.61 mg/g, 13.44 mg/g, 16.09 mg/g, 50.8 mg/g and 32.90 mg/g.

  2. Reactions of sulphur mustard on impregnated carbons.

    Science.gov (United States)

    Prasad, G K; Singh, Beer

    2004-12-31

    Activated carbon of surface area 1100 m2/gm is impregnated with 4% sodium hydroxide plus 3% Cr(VI) as CrO3 with and without 5% ethylene diamine (EDA), 4% magnesium nitrate and 5% ruthenium chloride by using their aqueous solutions. These carbons are characterized for surface area analysis by BET conventional method and exposed to the vapours of sulphur mustard (HD) at room temperature (30 degrees C). After 24 h, the reaction products are extracted in dichloromethane and analyzed using gas chromatography and mass spectrometry (GC-MS). Hemisulphur mustard, thiodiglycol, 1,4-oxathiane are observed to be the products of reaction between sulphur mustard and NaOH/CrO3/C system, whereas on NaOH/CrO3/EDA/C system HD reacted to give 1,4-thiazane. On Mg(NO3)2/C system it gave hemisulphur mustard and thiodiglycol. On RuCl3/C system it degraded to divinyl sulphone. Residual sulphur mustard is observed along with reaction products in all systems studied. Reaction mechanisms are also proposed for these interesting surface reactions. Above-mentioned carbons can be used in filtration systems for protection against hazardous gases such as sulphur mustard.

  3. Reactions of sulphur mustard on impregnated carbons

    International Nuclear Information System (INIS)

    Prasad, G.K.; Singh, Beer

    2004-01-01

    Activated carbon of surface area 1100 m 2 /gm is impregnated with 4% sodium hydroxide plus 3% Cr(Vi) as CrO 3 with and without 5% ethylene diamine (EDA), 4% magnesium nitrate and 5% ruthenium chloride by using their aqueous solutions. These carbons are characterized for surface area analysis by BET conventional method and exposed to the vapours of sulphur mustard (HD) at room temperature (30 deg. C). After 24 h, the reaction products are extracted in dichloromethane and analyzed using gas chromatography and mass spectrometry (GC-MS). Hemisulphur mustard, thiodiglycol, 1,4-oxathiane are observed to be the products of reaction between sulphur mustard and NaOH/CrO 3 /C system, whereas on NaOH/CrO 3 /EDA/C system HD reacted to give 1,4-thiazane. On Mg(NO 3 ) 2 /C system it gave hemisulphur mustard and thiodiglycol. On RuCl 3 /C system it degraded to divinyl sulphone. Residual sulphur mustard is observed along with reaction products in all systems studied. Reaction mechanisms are also proposed for these interesting surface reactions. Above-mentioned carbons can be used in filtration systems for protection against hazardous gases such as sulphur mustard

  4. Development of a Temperature Programmed Identification Technique to Characterize the Organic Sulphur Functional Groups in Coal

    Directory of Open Access Journals (Sweden)

    Moinuddin Ghauri

    2017-06-01

    Full Text Available The Temperature Programmed Reduction (TPR technique is employed for the characterisation of various organic sulphur functional groups in coal. The TPR technique is modified into the Temperature Programmed Identification technique to investigate whether this method can detect various functional groups corresponding to their reduction temperatures. Ollerton, Harworth, Silverdale, Prince of Wales coal and Mequinenza lignite were chosen for this study. High pressure oxydesulphurisation of the coal samples was also done. The characterization of various organic sulphur functional groups present in untreated and treated coal by the TPR method and later by the TPI method confirmed that these methods can identify the organic sulphur groups in coal and that the results based on total sulphur are comparable with those provided by standard analytical techniques. The analysis of the untreated and treated coal samples showed that the structural changes in the organic sulphur matrix due to a reaction can be determined.

  5. SULPHUR CONTAINING LICKS AND THEIR EFFECT ON THE ...

    African Journals Online (AJOL)

    amounts of sulphur, there are some of particular importance such as the vitamins thiamine and biotin. Sulphur is also ingested in the inorganic sulphide and sulphate forms, fractions of which are utilized in metabolic processes, whereas substantial portions are also excreted. It has been determined that thiol cornpounds.

  6. Sulphur-containing Amino Acids: Protective Role Against Free Radicals and Heavy Metals.

    Science.gov (United States)

    Colovic, Mirjana B; Vasic, Vesna M; Djuric, Dragan M; Krstic, Danijela Z

    2018-01-30

    Sulphur is an abundant element in biological systems, which plays an important role in processes essential for life as a constituent of proteins, vitamins and other crucial biomolecules. The major source of sulphur for humans is plants being able to use inorganic sulphur in the purpose of sulphur-containing amino acids synthesis. Sulphur-containing amino acids include methionine, cysteine, homocysteine, and taurine. Methionine and cysteine are classified as proteinogenic, canonic amino acids incorporated in protein structure. Sulphur amino acids are involved in the synthesis of intracellular antioxidants such as glutathione and N-acetyl cysteine. Moreover, naturally occurring sulphur-containing ligands are effective and safe detoxifying agents, often used in order to prevent toxic metal ions effects and their accumulation in human body. Literature search for peer-reviewed articles was performed using PubMed and Scopus databases, and utilizing appropriate keywords. This review is focused on sulphur-containing amino acids - methionine, cysteine, taurine, and their derivatives - glutathione and N-acetylcysteine, and their defense effects as antioxidant agents against free radicals. Additionally, the protective effects of sulphur-containing ligands against the toxic effects of heavy and transition metal ions, and their reactivation role towards the enzyme inhibition are described. Sulphur-containing amino acids represent a powerful part of cell antioxidant system. Thus, they are essential in the maintenance of normal cellular functions and health. In addition to their worthy antioxidant action, sulphur-containing amino acids may offer a chelating site for heavy metals. Accordingly, they may be supplemented during chelating therapy, providing beneficial effects in eliminating toxic metals. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

  7. A compact XRF unit for determining total sulphur content in coals

    International Nuclear Information System (INIS)

    Sumitra, T.; Chankow, N.; Punnachaiya, S.; Srisatit, S.

    1994-01-01

    A microcomputer based x-ray fluorescence (XRF) unit was developed for off-line determination of total sulphur content in coal samples. The unit consisted of the x-ray exciting/measuring set and the microcomputer with a plug-in interface card. An Fe-55 radioisotope was used as the exciting source while a krypton-filled proportional counter was used to measure x-rays from the samples. The x-ray spectrum was simultaneously displayed on the microcomputer screen. For quantitative determination of sulphur, the intensities of sulphur K x-rays as well as calcium K x-rays and scattered x-rays were taken into account. The unit was tested with finely-ground, dried and compressed lignite, subbituminous and bituminous samples. If was found that for low-calcium coals, the results were in good agreement with those obtained from the standard chemical analysis method within ± 0.2% and within ± 0.5%S for high-calcium coals. 2 refs., 2 tabs., 3 figs

  8. The reducibility of sulphuric acid and sulphate in aqueous solution

    International Nuclear Information System (INIS)

    Grauer, R.

    1991-07-01

    In connection with the Swedish project for final storage of spent fuel elements it was necessary to assess whether dissolved sulphate can corrode the copper canister. A simple reaction between copper and sulphate is thermodynamically impossible, but copper can react to give copper sulphide if an additional electron donor such as iron(II) is available. The problem was extended to the more general question of the reducibility of sulphur(VI) in dilute aqueous solution. Chemical reduction of sulphate does not take place in dilute solution at temperatures below 100 o C. In experiments on the reduction of sulphates under hydrothermal conditions a reaction only takes place at temperatures above 275-300 o C. The oxidising action of sulphuric acid on metals becomes perceptible only at acid concentrations over 45-50%. In experiments on the cathodic reduction of 74% sulphuric acid the formation of hydrogen sulphide and elementary sulphur starts, depending on the current density, at 50-130 o C, and polarographic measurements suggest that the reducible species is not the hydrogen sulphate ion but molecular sulphuric acid. The resistance of copper to oxygen-free sulphuric acid up to a concentration of 60% is well-known. Numerous processes in industrial electrochemistry take place in sulphuric acid or sulphate electrolytes. The reversible metal/metal-sulphate electrodes of lead and cadmium are unstable relative to the corresponding metal sulphides. Nevertheless the reversible lead sulphate electrode does not fail from sulphide formation. All these facts confirm that sulphur(VI) in dilute solution is completely inert towards chemical reducing agents and also to cathodic reduction. Thus corrosion of copper by sulphate under final-storage conditions and in the absence of sulphate reducing bacteria can be almost certainly be ruled out. (author) 5 figs., 85 refs

  9. Effects of acid conditions on element distribution beneath a sulphur basepad

    International Nuclear Information System (INIS)

    Sevigny, J.H.; Fennell, J.W.; Sharma, A.

    1997-04-01

    A reconnaissance-scale study was conducted to determine the extent of acid conditions beneath a sulphur basepad at Canadian Occidental's Balzac sour gas plant and to examine the effects of acid conditions on element distribution in the subsurface. Sulphur which is extracted from sour natural gas is stored in large blocks directly on the ground. The elemental sulphur will oxidize to H 2 SO 4 under aerobic conditions and with the proper microorganisms can result in possible removal of metals from the soil and transportation in the groundwater. The basepad at the sour gas plant is 36 years old and is covered by about 1 metre of elemental sulphur. EM31 terrain conductivity and electrical resistivity tomography geophysical surveys were conducted to determine aerial and subsurface bulk electrical conductivity. The objective was to locate the indurated layer using the geophysical techniques and soil boring. The extent of acid conditions beneath the sulphur block was determined. Migration rates for the site were also estimated. Results suggested that minimal soil and groundwater impact can be expected from sulphur blocks overlying properly buffered soils, and that synthetic liners beneath sulphur blocks may not be a necessary measure at sour gas plants in Alberta. 19 refs., 6 tabs., 6 figs., 5 appendices

  10. Sulphur Extraction at Bryan Mound

    Energy Technology Data Exchange (ETDEWEB)

    Kirby, Carolyn L [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Lord, Anna C. Snider [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-08-01

    The Bryan Mound caprock was subjected to extens ive sulphur mining prior to the development of the Strategic Petroleum Reserve. Undoubtedl y, the mining has modified the caprock integrity. Cavern wells at Bryan Mound have been subject to a host of well integr ity concerns with many likely compromised by the cavernous capro ck, surrounding corrosive environment (H 2 SO 4 ), and associated elevated residual temperatures al l of which are a product of the mining activities. The intent of this study was to understand the sulphur mining process and how the mining has affected the stability of the caprock and how the compromised caprock has influenced the integrity of the cavern wells. After an extensiv e search to collect pert inent information through state agencies, literature sear ches, and the Sandia SPR librar y, a better understanding of the caprock can be inferred from the knowledge gaine d. Specifically, the discovery of the original ore reserve map goes a long way towards modeling caprock stability. In addition the gained knowledge of sulphur mining - subs idence, superheated corrosive wa ters, and caprock collapse - helps to better predict the post mi ning effects on wellbore integrity. This page intentionally left blank

  11. Selective environmental stress from sulphur emitted by continental flood basalt eruptions

    Science.gov (United States)

    Schmidt, Anja; Skeffington, Richard; Thordarson, Thorvaldur; Self, Stephen; Forster, Piers; Rap, Alexandru; Ridgwell, Andy; Fowler, David; Wilson, Marjorie; Mann, Graham; Wignall, Paul; Carslaw, Ken

    2016-04-01

    Several biotic crises during the past 300 million years have been linked to episodes of continental flood basalt volcanism, and in particular to the release of massive quantities of magmatic sulphur gas species. Flood basalt provinces were typically formed by numerous individual eruptions, each lasting years to decades. However, the environmental impact of these eruptions may have been limited by the occurrence of quiescent periods that lasted hundreds to thousands of years. Here we use a global aerosol model to quantify the sulphur-induced environmental effects of individual, decade-long flood basalt eruptions representative of the Columbia River Basalt Group, 16.5-14.5 million years ago, and the Deccan Traps, 65 million years ago. For a decade-long eruption of Deccan scale, we calculate a decadal-mean reduction in global surface temperature of 4.5 K, which would recover within 50 years after an eruption ceased unless climate feedbacks were very different in deep-time climates. Acid mists and fogs could have caused immediate damage to vegetation in some regions, but acid-sensitive land and marine ecosystems were well-buffered against volcanic sulphur deposition effects even during century-long eruptions. We conclude that magmatic sulphur from flood basalt eruptions would have caused a biotic crisis only if eruption frequencies and lava discharge rates had been high and sustained for several centuries at a time.

  12. Abatements of reduced sulphur compounds, colour, and organic matter from indigo dyeing effluents by electrocoagulation.

    Science.gov (United States)

    Tünay, Olcay; Simşeker, Merve; Kabdaşli, Isik; Olmez-Hanci, Tugba

    2014-08-01

    In the present study, the treatability of indigo dyeing effluents by the electrocoagulation (EC) process using stainless steel electrodes was experimentally investigated. The samples used were concentrated with main pollutant parameters of chemical oxygen demand (COD) (1000-1100 mg/L), reduced sulphur species (over 2000 mg SO2-(3)/L), and colour (0.12-0.13 1/cm). The study focused on the effect of main operation parameters on the EC process performance in terms of abatement of reduced sulphur compounds as well as decolourization and organic matter reduction. Results indicated that the performance of EC proved to be high providing total oxidation of the reduced sulphur compounds, almost complete decolourization, and COD removal up to 90%. Increasing applied current density from 22.5 to 45 mA/cm2 appreciably improved abatement of the reduced sulphur compounds for Sample I, but a further increase in the applied current density to 67.5 mA/cm2 did not accelerate the conversion rate to sulphate. The process performance was adversely affected by increasing initial concentration of the reduced sulphur compounds. Decolourization and organic matter removal efficiency enhanced with increasing applied current density. The main removal mechanism of the reduced sulphur compounds by EC was explained as conversion to sulphate via oxidation. Conversion rate to sulphate fitted pseudo-first-order kinetics very well.

  13. Effects of Different Forms and Doses of Sulphur Application on Wheat

    Directory of Open Access Journals (Sweden)

    Halil Erdem

    2016-11-01

    Full Text Available Deficiency of sulphur (S is an important limiting factor of plant growth for sustainable agricultural production. The decline in sulphur dioxide emission, decrease in S-containing fertilizer consumption due to the high cost of S-fertilizers, breeding of new high yielding species are the well known causes of S-deficiency. A greenhouse experiment was conducted to investigate the effects of several doses of K2SO4-S, CaSO4-S and elemental-S applied on growth, shoot dry matter yield, S and N concentrations of wheat cultivar. The experiments were conducted in three soils differed from available S concentrations. Effects of different S-treatments (0, 25, 50 and 100 mg S kg-1 and S-forms had significant effects on shoot dry matter yields of plants. Sulphur from different S-sources did not increase shoot S-concentrations in Eskisehir and Konya soils, but increase was significant obtained in the Harran soil. Shoot S-concentration in Harran soil for zero K2SO4 treatment was 0.09%, the values were 0.22, 0.26 and 0.27% respectively for 25, 50 and 100 mg kg-1 treatments. The results indicated significant effects of S-treatments on plant growth and yield mostly based on soil properties, especially the available S-levels

  14. RNA-based molecular survey of biodiversity of limestone tombstone microbiota in response to atmospheric sulphur pollution.

    Science.gov (United States)

    Villa, F; Vasanthakumar, A; Mitchell, R; Cappitelli, F

    2015-01-01

    Outdoor stoneworks sustain biofilm formation and are constantly at risk of deterioration by micro-organisms. In this study, the biofilm microflora of historic limestone tombstones located in a highly polluted urban environment (Cambridge, MA) and in a less polluted location (Lexington, MA) were compared using comprehensive RNA-based molecular analyses of 16S rRNA gene sequences as well as sequences of genes for different pathways of sulphur metabolism (soxB, apsA, dsrA). The metabolically active micro-organisms detected by denaturing gradient gel electrophoresis analysis of 16S rRNA fragments were predominantly represented by cyanobacteria (belonging to the family Nostocaceae and to the genus Chroococcidiopsis) in both polluted and unpolluted environments. The investigation of soxB, apsA, dsrA transcripts reflected the abundance and the diversity of sulphur-oxidizing and sulphate-reducing bacteria in the Cambridge samples in comparison with the Lexington samples. The investigation revealed that in addition to phototrophic sulphur bacteria belonging to the genera Thiocapsa, Halochromatium, Allochromatium, Thiococcus and Thermochromatium, other sulphate-oxidizing prokaryotes (e.g. the genus Thiobacillus) as well as sequences of Deltaproteobacteria from the genus Desulfovibrio occurred at the polluted urban site. The interactions between the main functional groups retrieved from the limestone tombstones were discussed. The biofilm microflora inhabiting historic limestones are a multi-component open ecosystem sensitively reacting to all environmental factors including air pollutants. Little is known about specific target groups that are active in the biofilm and their physiological functions. For the first time, transcripts involved in important energy-yielding processes were investigated to reveal the metabolic capabilities of the microflora in response to atmospheric sulphur pollution. This work provides novel and important information about the ecology of limestone

  15. Seasonal and annual variability of coastal sulphur plumes in the northern Benguela upwelling system.

    Directory of Open Access Journals (Sweden)

    Thomas Ohde

    Full Text Available We investigated the seasonal and annual variability of surface sulphur plumes in the northern Benguela upwelling system off Namibia because of their significant impacts on the marine ecosystem, fishing industry, aquaculture farming and tourism due to their toxic properties. We identified the sulphur plumes in ocean colour satellite data of the medium resolution imaging spectrometer (MERIS for the 2002-2012 time period using the differences in the spectral properties of Namibian Benguela optical water types. The sulphur events have a strong seasonal cycle with pronounced main and off-seasons forced by local and remote-driven processes. The main peak season is in late austral summer and early austral autumn at the beginning of the annual upwelling cycle caused by increasing equatorwards alongshore winds. The sulphur plume activity is high between February and April during the seasonal oxygen minimum associated with the seasonal reduction of cross-shore ventilation of the bottom waters, the seasonal southernmost position of the Angola Benguela Frontal Zone, the seasonal maximum of water mass fractions of South Atlantic and Angola Gyre Central Waters as well as the seasonal arrival of the downwelling coastal trapped waves. The off-season is in austral spring and early austral summer during increased upwelling intensity and enhanced oxygen supply. The annual variability of sulphur events is characterized by very high activities in years 2004, 2005 and 2010 interrupted by periods of lower activity in years 2002 to 2003, 2006 to 2009 and 2011 to 2012. This result can be explained by the relative contributions or adding effects of local and remote-driven forces (from the equatorial area. The probability for the occurrence of sulphur plumes is enhanced in years with a lower annual mean of upwelling intensity, decreased oxygen supply associated with decreased lateral ventilation of bottom waters, more southern position of the Angola Benguela Frontal Zone

  16. Seasonal and annual variability of coastal sulphur plumes in the northern Benguela upwelling system.

    Science.gov (United States)

    Ohde, Thomas; Dadou, Isabelle

    2018-01-01

    We investigated the seasonal and annual variability of surface sulphur plumes in the northern Benguela upwelling system off Namibia because of their significant impacts on the marine ecosystem, fishing industry, aquaculture farming and tourism due to their toxic properties. We identified the sulphur plumes in ocean colour satellite data of the medium resolution imaging spectrometer (MERIS) for the 2002-2012 time period using the differences in the spectral properties of Namibian Benguela optical water types. The sulphur events have a strong seasonal cycle with pronounced main and off-seasons forced by local and remote-driven processes. The main peak season is in late austral summer and early austral autumn at the beginning of the annual upwelling cycle caused by increasing equatorwards alongshore winds. The sulphur plume activity is high between February and April during the seasonal oxygen minimum associated with the seasonal reduction of cross-shore ventilation of the bottom waters, the seasonal southernmost position of the Angola Benguela Frontal Zone, the seasonal maximum of water mass fractions of South Atlantic and Angola Gyre Central Waters as well as the seasonal arrival of the downwelling coastal trapped waves. The off-season is in austral spring and early austral summer during increased upwelling intensity and enhanced oxygen supply. The annual variability of sulphur events is characterized by very high activities in years 2004, 2005 and 2010 interrupted by periods of lower activity in years 2002 to 2003, 2006 to 2009 and 2011 to 2012. This result can be explained by the relative contributions or adding effects of local and remote-driven forces (from the equatorial area). The probability for the occurrence of sulphur plumes is enhanced in years with a lower annual mean of upwelling intensity, decreased oxygen supply associated with decreased lateral ventilation of bottom waters, more southern position of the Angola Benguela Frontal Zone, increased mass

  17. Being green on sulphur: Targets, measures and side-effects

    DEFF Research Database (Denmark)

    Kontovas, Christos A.; Panagakos, George; Psaraftis, Harilaos N.

    2016-01-01

    to sea to reduce congestion, and might ultimately (under certain circumstances) increase the overall level of CO2 emissions along the entire supply chain. The purpose of this chapter is to investigate the potential effect of sulphur regulations on the share of cargo transported by the waterborne mode vis......Green House Gas (GHG) emissions are not the only emissions of concern to the international transport community. SOx emissions are non-GHG emissions that are caused by the presence of sulphur in the fuel. As the maximum percentage of sulphur in automotive and aviation fuels is strictly regulated...

  18. Distribution and isotopic abundance of sulphur in recent marine sediments off southern California

    Energy Technology Data Exchange (ETDEWEB)

    Kaplan, I R; Emergy, K O; Rittenberg, S C

    1963-01-01

    Analyses of sulphur compounds in basin sediments off southern California indicate that elemental sulphur, free sulphide, hydrotroilite, organic sulphur, sulphate and pyrite are present in quantities that vary with environment and depth in the sediments. Pyrite is generally the most abundant form, occurring in oxidizing as well as in reducing sediments and often constituting 90% of total sulphur. A material balance indicates that the total sulphur content is far in excess of the sulphate-sulphur initially trapped in the interstitial water. This evidence, together with failure to detect significant alternate sources, suggests that sulphate-sulphur is extracted from the overlying sea water at the sediment-water interface. Isotope measurements confirm many of the conclusions suggested by the quantitative chemical analyses. The show that biological sulphate reduction is the single most important process in the sulphur cycle. The sulphide released is converted to hydrotrolite and then to pyrite. Elemental and organic sulphur appear to be continually forming and reacting in the sediment column. The organic sulphur released from decaying organic matter apparently plays only a small role in the sulphur economy. Enrichment in S/sup 32/ ranging from 9 to 62% was measured in pyrite fragments, a spread similar to that previously observed in ancient sediments. Data from field and laboratory experiments were combined to determine rate of sulphate reduction, number of sulphate reducing bacteria and the amount of organic matter decomposed during sulphate reduction in the sediment, as well as rate of renewal of water in the basins. The results suggest that the methods used may have many applications for elucidating in situ rate processes.

  19. Pyrotechnic countermeasures: IV. Radiometric performance of a sulphur-based Flare composition

    Energy Technology Data Exchange (ETDEWEB)

    Koch, Ernst-Christian [NATO Munitions Safety Information Analysis Center (MSIAC), Brussels (Belgium)

    2008-10-15

    Radiometric performance of a sulphur-based flare composition has been investigated. Composition comprising sulphur, potassium perchlorate and antimony sulphide has acceptable band ratio but an order of magnitude weaker spectral efficiency than typical carbon-based compositions. The use of other sulphur compounds with potential for increased performance is discussed. For part III see Ref. [1]. (Abstract Copyright [2008], Wiley Periodicals, Inc.)

  20. Sulphur XANES Analysis of Cultured Human Prostate Cancer Cells

    International Nuclear Information System (INIS)

    Kwiatek, W.M.; Podgorczyk, M.; Paluszkiewicz, Cz.; Balerna, A.; Kisiel, A.

    2008-01-01

    Prostate cancer is one of the most commonly diagnosed cancers in men throughout the world. It is believed that changes to the structure of protein binding sites, altering its metabolism, may play an important role in carcinogenesis. Sulphur, often present in binding sites, can influence such changes through its chemical speciation. Hence there is a need for precise investigation of coordination environment of sulphur. X-ray absorption near edge structure spectroscopy offers such possibility. Cell culture samples offer histologically well defined areas of good homogeneity, suitable for successful and reliable X-ray absorption near edge structure analysis. This paper presents sulphur speciation data collected from three different human prostate cancer cell lines (PC-3, LNCaP and DU-145). Sulphur X-ray absorption near edge structure analysis was performed on K-edge structure. The spectra of cells were compared with those of cancerous tissue and with organic substances as well as inorganic compounds. (authors)

  1. Absolute photoabsorption oscillator strengths by electron energy loss methods: the valence and S 2p and 2s inner shells of sulphur dioxide in the discrete and continuum regions (3.5-260 eV)

    International Nuclear Information System (INIS)

    Feng, R.; Cooper, G.; Burton, G.R.; Brion, C.E.; Avaldi, L.

    1999-01-01

    Absolute photoabsorption oscillator strengths (cross-sections) for the valence shell discrete and continuum regions of sulphur dioxide from 3.5 to 51 eV have been measured using high resolution (∼0.05 eV FWHM) dipole (e,e) spectroscopy. A wide-range spectrum, covering both the valence shell and the S 2p and 2s inner shells, has also been obtained from 5 to 260 eV at low resolution (∼1 eV FWHM), and this has been used to determine the absolute oscillator strength scale using valence shell TRK (i.e., S(0)) sum-rule normalization. The present measurements have been undertaken in order to investigate the recently discovered significant quantitative errors in our previously published low resolution dipole (e,e) work on sulphur dioxide (Cooper et al., Chem. Phys. 150 (1991) 237; 150 (1991) 251). These earlier measurements were also in poor agreement with other previously published direct photoabsorption measurements. We now report new absolute photoabsorption oscillator strengths using both high and low resolution dipole (e,e) spectroscopies. These new measurements cover a wider energy range and are much more consistent with the previously published direct photoabsorption measurements. The accuracy of our new measurements is confirmed by an S(-2) dipole sum-rule analysis which gives a static dipole polarizability for sulphur dioxide in excellent agreement (within 3.5%) with previously reported polarizability values. Other dipole sums S(u) (u=-1,-3 to -6,-8,-10) and logarithmic dipole sums L(u) (u=-1 to -6) are also determined from the presently reported absolute oscillator strength distributions. (Copyright (c) 1999 Elsevier Science B.V., Amsterdam. All rights reserved.)

  2. Radioisotopic determination methods of sulphur dispersion and sulphur blooming in rubber compounds

    International Nuclear Information System (INIS)

    Goraczka, W.; Koczorowska, E.

    1997-01-01

    It is well known that the concentration of sulphur in rubber compounds essentially effects the structure of the vulkanizate network. But there are no efficient and accurate methods to estimate the dispersion and migration (blooming) of curatives in raw rubber. In the work radioisotope methods have been analyzed to study the dispersion of curatives, physical and chemical processes in rubber and to optimize technical conditions of tire production. The radioactivity of the 35 S isotope introduced into rubber compounds has been measured by volumetric and surface methods. It was proved that the radioisotopic methods can be used in the studies. Experimental data of the effect of selected technological factors on these processes are presented. Rubber compounds containing soluble sulphur were made for such investigations. These methods permit detection of concentrations 10 -6 g of the radioactive isotope per 0.1 g of rubber compound. The sensitivity of these methods enables the investigation of radioisotope behaviour in rubber compounds during processing on an industrial scale without any hazards for workers

  3. Determination of sulphur with total reflection x-ray spectrometry

    International Nuclear Information System (INIS)

    Steinmeyer, S.; Kolbesen, B.O.

    2000-01-01

    The potential and limitations of total reflection x-ray spectrometry (TXRF) were tested for the quantitative determination of the light element sulphur in inorganic and biological samples. As representatives of inorganic samples alkali, transition metal, magnesium and aluminum sulphates were investigated. As biological samples the sulphur containing amino acid methionine and the pharmaceutical drug insulin were chosen. All measurements were performed on a TXRF-spectrometer EXTRA IIA (Atomika Instruments, Oberschleissheim/Germany) using tungsten L-radiation as the excitation tube. Various concentrations of all samples ranging from 20 mg/l to 0.5 mg/l were determined. In addition the surface topography and thickness of the dry residue of these samples were investigated with SEM and a thickness profilometer (Alpha-Step). The result show that the reliable determination of sulphur in sulphates depends on the cation involved. Alkali sulphates like Na 2 SO 4 , or K 2 SO 4 form bulky residues resulting in significant deviations of the recovery rate of sulphur. In this case the use of smoothing detergents like 1 % HF, 1 % malic acid and 2 % hydrazinhydrat was found to be necessary for accurate determination. The results for the biological samples agree well with the expected values. The investigations lead to the conclusion that TXRF combined with a proper samples preparation is well suited for the determination of sulphur in different samples with various concentrations and matrices. (author)

  4. Ethanol and biogas production after steam pretreatment of corn stover with or without the addition of sulphuric acid

    Directory of Open Access Journals (Sweden)

    Bondesson Pia-Maria

    2013-01-01

    Full Text Available Abstract Background Lignocellulosic biomass, such as corn stover, is a potential raw material for ethanol production. One step in the process of producing ethanol from lignocellulose is enzymatic hydrolysis, which produces fermentable sugars from carbohydrates present in the corn stover in the form of cellulose and hemicellulose. A pretreatment step is crucial to achieve efficient conversion of lignocellulosic biomass to soluble sugars, and later ethanol. This study has investigated steam pretreatment of corn stover, with and without sulphuric acid as catalyst, and examined the effect of residence time (5–10 min and temperature (190–210°C on glucose and xylose recovery. The pretreatment conditions with and without dilute acid that gave the highest glucose yield were then used in subsequent experiments. Materials pretreated at the optimal conditions were subjected to simultaneous saccharification and fermentation (SSF to produce ethanol, and remaining organic compounds were used to produce biogas by anaerobic digestion (AD. Results The highest glucose yield achieved was 86%, obtained after pretreatment at 210°C for 10 minutes in the absence of catalyst, followed by enzymatic hydrolysis. The highest yield using sulphuric acid, 78%, was achieved using pretreatment at 200°C for 10 minutes. These two pretreatment conditions were investigated using two different process configurations. The highest ethanol and methane yields were obtained from the material pretreated in the presence of sulphuric acid. The slurry in this case was split into a solid fraction and a liquid fraction, where the solid fraction was used to produce ethanol and the liquid fraction to produce biogas. The total energy recovery in this case was 86% of the enthalpy of combustion energy in corn stover. Conclusions The highest yield, comprising ethanol, methane and solids, was achieved using pretreatment in the presence of sulphuric acid followed by a process configuration in

  5. Improved Performance and Safety for High Energy Batteries Through Use of Hazard Anticipation and Capacity Prediction

    Science.gov (United States)

    Atwater, Terrill

    1993-01-01

    Prediction of the capacity remaining in used high rate, high energy batteries is important information to the user. Knowledge of the capacity remaining in used batteries results in better utilization. This translates into improved readiness and cost savings due to complete, efficient use. High rate batteries, due to their chemical nature, are highly sensitive to misuse (i.e., over discharge or very high rate discharge). Battery failure due to misuse or manufacturing defects could be disastrous. Since high rate, high energy batteries are expensive and energetic, a reliable method of predicting both failures and remaining energy has been actively sought. Due to concerns over safety, the behavior of lithium/sulphur dioxide cells at different temperatures and current drains was examined. The main thrust of this effort was to determine failure conditions for incorporation in hazard anticipation circuitry. In addition, capacity prediction formulas have been developed from test data. A process that performs continuous, real-time hazard anticipation and capacity prediction was developed. The introduction of this process into microchip technology will enable the production of reliable, safe, and efficient high energy batteries.

  6. Efficacy and phytotoicity of lime sulphur in organic apple production

    NARCIS (Netherlands)

    Holb, I.J.; Jong, de P.F.; Heijne, B.

    2003-01-01

    Curative and preventive efficacy and phytotoxicity of lime sulphur spray schedules, based on a warning system, were evaluated in the Netherlands during two growing seasons under field conditions. In most cases, lime sulphur treatments applied either curatively or preventively resulted in

  7. First Description of Sulphur-Oxidizing Bacterial Symbiosis in a Cnidarian (Medusozoa Living in Sulphidic Shallow-Water Environments.

    Directory of Open Access Journals (Sweden)

    Sylvie Abouna

    Full Text Available Since the discovery of thioautotrophic bacterial symbiosis in the giant tubeworm Riftia pachyptila, there has been great impetus to investigate such partnerships in other invertebrates. In this study, we present the occurrence of a sulphur-oxidizing symbiosis in a metazoan belonging to the phylum Cnidaria in which this event has never been described previously.Scanning Electron Microscope (SEM, Transmission Electron Microscope (TEM observations and Energy-dispersive X-ray spectroscopy (EDXs analysis, were employed to unveil the presence of prokaryotes population bearing elemental sulphur granules, growing on the body surface of the metazoan. Phylogenetic assessments were also undertaken to identify this invertebrate and microorganisms in thiotrophic symbiosis. Our results showed the occurrence of a thiotrophic symbiosis in a cnidarian identified as Cladonema sp.This is the first report describing the occurrence of a sulphur-oxidizing symbiosis in a cnidarian. Furthermore, of the two adult morphologies, the polyp and medusa, this mutualistic association was found restricted to the polyp form of Cladonema sp.

  8. First Description of Sulphur-Oxidizing Bacterial Symbiosis in a Cnidarian (Medusozoa) Living in Sulphidic Shallow-Water Environments.

    Science.gov (United States)

    Abouna, Sylvie; Gonzalez-Rizzo, Silvina; Grimonprez, Adrien; Gros, Olivier

    2015-01-01

    Since the discovery of thioautotrophic bacterial symbiosis in the giant tubeworm Riftia pachyptila, there has been great impetus to investigate such partnerships in other invertebrates. In this study, we present the occurrence of a sulphur-oxidizing symbiosis in a metazoan belonging to the phylum Cnidaria in which this event has never been described previously. Scanning Electron Microscope (SEM), Transmission Electron Microscope (TEM) observations and Energy-dispersive X-ray spectroscopy (EDXs) analysis, were employed to unveil the presence of prokaryotes population bearing elemental sulphur granules, growing on the body surface of the metazoan. Phylogenetic assessments were also undertaken to identify this invertebrate and microorganisms in thiotrophic symbiosis. Our results showed the occurrence of a thiotrophic symbiosis in a cnidarian identified as Cladonema sp. This is the first report describing the occurrence of a sulphur-oxidizing symbiosis in a cnidarian. Furthermore, of the two adult morphologies, the polyp and medusa, this mutualistic association was found restricted to the polyp form of Cladonema sp.

  9. The implications of the new sulphur limits on the European Ro-Ro sector

    DEFF Research Database (Denmark)

    Zis, Thalis; Psaraftis, Harilaos N.

    -based alternatives. The exact repercussions of the new sulphur limits are difficult to identify in the wake of significant recent reductions of the fuel prices for both low-sulphur and heavy fuel oil. This paper presents a modal split model that estimates modal shifts vis-a-vis competing maritime and land......In an effort to reduce the environmental impacts of maritime transportation, the International Maritime Organization (IMO) designated special Sulphur Emission ControlAreas (SECAs) where ships are required to use low-sulphur fuel. In January 2015, the sulphur limit within SECAs was lowered to 0.......1%, which can only be achieved if vessels are using pricier ultra-low sulphur fuel, or invest in abatement technologies. The increased operating costs borne by Ro-Ro operators in SECAs due to the stricter limits can result in the shutting down of some routes and a redistribution of cargo flows with land...

  10. Sulphur-oxidising and Sulphate-reducing Communities in Brazilian Mangrove Sediments

    NARCIS (Netherlands)

    Varon-Lopez, Maryeimy; Dias, A.C.F; Fasanella, C.C.; Durrer, A.; Melo, I.S.; Kuramae, E.E.; Andreote, F.D.

    2014-01-01

    Mangrove soils are anaerobic environments rich in sulphate and organic matter. Although the sulphur cycle is one of the major actors in this ecosystem, little is known regarding the sulphur bacteria communities in mangrove soils. We investigated the abundance, composition and diversity of

  11. Di- or polysulphide-bound biomarkers in sulphur-rich geomacromolecules as revealed by selective chemolysis

    Science.gov (United States)

    Kohnen, Math E. l.; Sinninghe Damsté, Jaap S.; Kock-van Dalen, A. c.; Jan, W. De Leeuw

    1991-05-01

    Three types of sulphur-rich high-molecular-weight material in the alkylsulphide, the polar, and the asphaltene fractions isolated from the bitumen of an immature bituminous shale from the Vena del Gesso basin (Italy) were desulphurised using Raney Ni and were treated with MeLi/MeI, a chemical degradation method which cleaves selectively and quantitatively di- or polysulphide linkages. The products formed were characterised by gas chromatography-mass spectrometry. Raney Ni desulphurisation revealed that these S-rich macromolecules are in substantial part composed of sulphur-linked biomarkers with linear, branched, isoprenoid, steroid, hopanoid, and carotenoid carbon skeletons. MeLi/Mel treatment provided evidence that a major part of the total amount of macromolecularly bound biomarkers are linked via di- or polysulphide moieties to the macromolecular network. Since the di- or polysulphide linkages are attached at specific positions of the bound biomarkers it is proposed that they are formed by intermolecular incorporation reactions of HS x- into low-molecular-weight functionalised biological lipids during early diagenesis. The different properties (solubility and molecular weight) of the sulphur-rich macromolecules in the alkylsulphide, the resin, and the asphaltene fractions can be explained simply by differences in degree of sulphur cross-linking.

  12. Analytical protocols for the determination of sulphur compounds characteristic of the metabolism of Chlorobium limicola

    Directory of Open Access Journals (Sweden)

    A. Aliboni

    2015-09-01

    Full Text Available Chlorobium limicola belongs to the green sulphur bacteria that has a potential for technological applications such as biogas clean up oxidising hydrogen sulphide to elemental sulphur through photosynthetic process. In the present work, analytical methods are described for the determination of different sulphur species in C. limicola cultures – sulphide by GC-FPD, sulphate by ionic HPLC and elemental sulphur by RP HPLC. The latter method eliminates the need for chloroform extraction of water suspensions of elemental sulphur. Data from sulphide and elemental sulphur analyses have been compared with ones coming from more traditional analytical methodologies.

  13. Sulphur and lead isotopes in strata-bound deposits, ch. 8

    International Nuclear Information System (INIS)

    Sangster, D.F.

    1976-01-01

    The use of sulphur and lead isotopes as isotopic tracers in the study of ore deposits containing these elements is reviewed. A discussion of the general theory, including abundance and fractionation of sulphur isotopes, single-stage leads, and anomalous leads (two-stage) is given. Attention is paid to sulphur isotopes enclosed in deposits which are located in marine host rocks and in rocks of continental or near-continental origin, as well as in deposits of the conglomerate-U(-Au) type. The lead isotope content of volcanogenic massive sulphide deposits and carbonate-hosted lead-zinc deposits is discussed

  14. Hydrothermal Alteration in an Acid-Sulphate Geothermal Field: Sulphur Springs, Saint Lucia

    Science.gov (United States)

    Joseph, E. P.; Barrett, T. J.

    2017-12-01

    Sulphur Springs is a vigorous geothermal field associated with the Soufrière Volcanic Centre in southern Saint Lucia. Bubbling hydrothermal pools are rich in sodium-calcium sulphate, with pHs of 3-7 and temperatures of 41-97ºC. Fumaroles have temperatures up to, and at times above, 100°C. Gases from bubbling pools and fumaroles have high contents of CO2 (601-993 mmol/mol) and H2S (3-190 mmol/mol). To investigate the nature and extent of hydrothermal alteration, detailed chemical analysis was carried out on 25 altered rocks, 10 sediments from pools and creeks in the main discharge area, and 15 little-altered rocks up to 2 km away from geothermal field. Eight altered samples were also analysed for stable isotope compositions, with mineralogy determined by X-ray diffraction and mineral liberation analysis. Least-altered host rocks comprise calc-alkaline feldspar-quartz-porphyritic dacites of near-uniform composition that form massive domes and volcaniclastic units. These rocks were emplaced 10-30 Ka ago (Lindsay et al. 2013). Within the geothermal field, the dacites have been highly altered to kaolinite, quartz, cristobalite, alunite, natroalunite, smectite, native sulphur, jarosite, gypsum and amorphous compounds. Muds from grey to blackish hydrothermal pools additionally contain iron sulphides, mainly pyrite. Despite intense alteration of the original dacites, Zr and Ti have remained essentially immobile, allowing the calculation of mass changes. Major depletions of Fe, Mg, Ca, Na and commonly Si occur over an area of at least 200 x 400 m. The most altered rocks also show losses of Al, light REE and Y, implying leaching by highly acidic waters. A few altered rocks have, however, gained Al together with Si and P. Also present are m-scale zones of silica + native sulphur, wherein the silica appears to represent a residue from the leaching of dacite, rather than a hydrothermal addition. Delta-34S values of samples containing mixtures of sulphates, native sulphur and

  15. Measurement of sulphur-35 in the coolant gas of the Windscale Advanced Gas-Cooled Reactor

    International Nuclear Information System (INIS)

    Sandalls, F.J.

    1978-03-01

    Sulphur is an important element in some food chains and the release of radioactive sulphur to the environment must be closely controlled if the chemical form is such that it is available or potentially available for entering food chains. The presence of sulphur-35 in the coolant gas of the Windscale Advanced Gas-Cooled Reactor warranted a study to assess the quantity and chemical form of the radioactive sulphur in order to estimate the magnitude of the potential environmental hazard which might arise from the release of coolant gas from Civil Advanced Gas-Cooled Reactors. A combination of gas chromatographic and radiochemical analyses revealed carbonyl sulphide to be the only sulphur-35 compound present in the coolant gas of the Windscale Reactor. The concentration of carbonyl sulphide was found to lie in the range 40 to 100 x 10 -9 parts by volume and the sulphur-35 specific activity was about 20 mCi per gramme. The analytical techniques are described in detail. The sulphur-35 appears to be derived from the sulphur and chlorine impurities in the graphite. A method for the preparation of carbonyl sulphide labelled with sulphur-35 is described. (author)

  16. Isotope exchange reaction in uranous-uranyl-sulphuric acid system

    International Nuclear Information System (INIS)

    Ling Daren; Yue Tingsheng; Mu Dehai; Wang Yani

    1990-01-01

    The kinetics of the isotope exchange reaction between U(IV) and U(VI) has been studied in low concentrations of sulphuric acid. A minimum exchange rate appears at 0.25 M H 2 SO 4 . From the rates at different temperatures ranging from 20deg to 35deg C, an apparent activation energy of 86 kcal/mole was calculated. The exchange rate was found to be accelerated by the addition of ferrous ions, and a half-life of less than 1 s, was obtained. Probable mechanisms for the acceleration of the uranium isotope exchange reactions by acidity and ferrous ions are proposed. (orig.)

  17. Mesoporous titanium-manganese dioxide for sulphur mustard and soman decontamination

    International Nuclear Information System (INIS)

    Stengl, Vaclav; Bludska, Jana; Oplustil, Frantisek; Nemec, Tomas

    2011-01-01

    Highlights: → New nano-dispersive materials for warfare agents decontamination. → 95% decontamination activities for sulphur mustard. → New materials base on titanium and manganese oxides. -- Abstract: Titanium(IV)-manganese(IV) nano-dispersed oxides were prepared by a homogeneous hydrolysis of potassium permanganate and titanium(IV) oxo-sulphate with 2-chloroacetamide. Synthesised samples were characterised using Brunauer-Emmett-Teller (BET) surface area and Barrett-Joiner-Halenda porosity (BJH), X-ray diffraction (XRD), infrared spectroscopy (IR), and scanning electron microscopy (SEM). These oxides were taken for an experimental evaluation of their reactivity with sulphur mustard (HD or bis(2-chloroethyl)sulphide) and soman (GD or (3,3'-dimethylbutan-2-yl)-methylphosphonofluoridate). Mn 4+ content affects the decontamination activity; with increasing Mn 4+ content the activity increases for sulphur mustard and decreases for soman. The best decontamination activities for sulphur mustard and soman were observed for samples TiMn 3 7 with 18.6 wt.% Mn and TiMn 5 with 2.1 wt.% Mn, respectively.

  18. Fractal and variability analysis of simulations in ozone level due to oxides of nitrogen and sulphur

    Science.gov (United States)

    Bhardwaj, Rashmi; Pruthi, Dimple

    2017-10-01

    Air pollution refers to the release of pollutants into the air. These pollutants are detrimental to human the planet as a whole. Apart from causing respiratory infections and pulmonary disorders, rising levels of Nitrogen Dioxide is worsening ozone pollution. Formation of Ground-level ozone involves nitrogen oxides and volatile gases in the sunlight. Volatile gases are emitted from vehicles primarily. Ozone is harmful gas and its exposure can trigger serious health effects as it damages lung tissues. In order to decrease the level of ozone, level of oxides leading to ozone formation has to be dealt with. This paper deals with the simulations in ozone due to oxides of nitrogen and sulphur. The data from Central Pollution Control Board shows positive correlation for ozone with oxides of sulphur and nitrogen for RK Puram, Delhi in India where high concentration of ozone has been found. The correlation between ozone and sulphur, nitrogen oxides is moderate during summer while weak during winters. Ozone with nitrogen and sulphur dioxide follow persistent behavior as Hurst exponent is between 0.5 and 1. The fractal dimension for Sulphur dioxide is 1.4957 indicating the Brownian motion. The behavior of ozone is unpredictable as index of predictability is close to zero.

  19. Investigation on the effect of heavy diesel fraction properties on product sulphur during ultra deep diesel hydrodesulphurization

    Energy Technology Data Exchange (ETDEWEB)

    Stratiev, D.; Tzingov, T. [Research and Development Dept., Lukoil Neftochim Bourgas, Bourgas (Bulgaria); Galkin, V. [Future Development Dept., Lukoil Neftochim Bourgas, Bourgas (Bulgaria)

    2006-02-01

    This work investigates the hydrotreatment of heavy diesel fractions in order to achieve product sulphurs of 50 and 10 ppm. The heavy diesel fractions were obtained in the Lukoil Neftochim Bulgaria (LNB) crude distillation and vacuum distillation units (SRGO1, SRGO2, AGO, LVGO ASTM D-86 95%vol. of 360, 392 395, and 377 C respectively) by distillation of crude oil type ''Ural'', containing some quantities of naphtha, atmospheric residue, vacuum gas oil and low sulphur crude oil, in the mild hydrocracking unit (MHC diesel 95%vol. of 389 C) and in the fluid catalytic cracking unit - heavy cycle oil (FCC HCO; 95%vol. of 360 C). The diesel fractions were hydrotreated in a trickle bed pilot plant at following conditions: reactor inlet temperature range of 300-380 C; liquid hourly space velocity (LHSV) range of 0.5-3.0 h{sup -1}, total reactor pressure range of 3.5- 7.0 MPa; treating gas/feedstock ratio of 250 Nm{sup 3}/m{sup 3}. It was found that in the investigated range of operating conditions the product sulphur depended linearly on the LHSV. As a measure of the diesel hydrodesulphurization (HDS) reactivity the LHSV at 360 C reactor inlet temperature was interpolated at a constant product sulphur level of 50 ppm and extrapolated at 10 ppm sulphur. It was found that the most refractory feedstock was the diesel mixture 80%SRGO1 / 20%FCCHCO (LHSV of 0.4 h{sup -1} for 50 ppm and 0.2 h{sup -1} for 10 ppm sulphur). The catalyst volume increase required to reduce the product sulphur from 50 to 10 ppm was found to be as high as twice for all diesel fractions except the MHC diesel. This material required five times the catalyst volume for the product sulphur reduction from 50 to 10 ppm. The total reactor pressure was found to have less impact on the product sulphur than the LHSV. Doubling the reactor pressure from 3.5 to 7.0 MPa by hydrotreatment of LVGO reduced the product sulphur as low as twice while the reduction of the LHSV from 1 to 0.5 h{sup -1} at a

  20. Interrogating trees for isotopic archives of atmospheric sulphur deposition and comparison to speleothem records

    International Nuclear Information System (INIS)

    Wynn, P.M.; Loader, N.J.; Fairchild, I.J.

    2014-01-01

    Palaeorecords which depict changes in sulphur dynamics form an invaluable resource for recording atmospheric pollution. Tree rings constitute an archive that are ubiquitously available and can be absolutely dated, providing the potential to explore local- to regional-scale trends in sulphur availability. Rapid isotopic analysis by a novel “on-line” method using elemental analyser isotope ratio mass spectrometry (EA-IRMS) is developed, achieving sample precision of <0.4‰ using sample sizes of 40 mg wood powder. Tree cores from NE Italy show trends in pollution, evidenced through increasing concentrations of sulphur towards the youngest growth, and inverse trends in sulphur isotopes differentiating modern growth with light sulphur isotopes (+0.7‰) from pre-industrial growth (+7.5‰) influenced by bedrock composition. Comparison with speleothem records from the same location demonstrate replication, albeit offset in isotopic value due to groundwater storage. Using EA-IRMS, tree ring archives form a valuable resource for understanding local- to regional-scale sulphur pollution dynamics. - Highlights: • Sulphur isotopes from tree rings are analysed using ‘on-line’ EA combustion. • Isotopes differentiate modern growth influenced by pollution from pre-industrial growth. • Biogeochemical cycling imparts minimal delay in sulphur incorporation into tree rings. • Trends in pollution are replicated between speleothems and trees from the same location. - Sulphur isotopes extracted from tree ring records are used to identify twentieth century pollution dynamics at the local- to regional-scale

  1. Effect of Thiobacillus thioparus 1904 and sulphur addition on odour emission during aerobic composting.

    Science.gov (United States)

    Gu, Wenjie; Sun, Wen; Lu, Yusheng; Li, Xia; Xu, Peizhi; Xie, Kaizhi; Sun, Lili; Wu, Hangtao

    2018-02-01

    The effects of sulphur and Thiobacillus thioparus 1904 on odour emissions during composting were studied. Results indicated that the sulphur addition reduced the pH and decreased cumulative emission of ammonia and the nitrogen loss by 47.80% and 44.23%, respectively, but the amount of volatile sulphur compounds (VSCs) and the sulphur loss increased. The addition of T. thioparus 1904 effectively reduced the cumulative emissions of H 2 S, methyl sulphide, methanethiol, dimethyl disulphide and the sulphur loss by 33.24%, 81.24%, 32.70%, 54.22% and 54.24%, respectively. T. thioparus 1904 also limited the nitrogen loss. The combined application of sulphur and T. thioparus 1904 resulted in the greatest amount of nitrogen retention. The accumulation of ammonia emissions was reduced by 63.33%, and the nitrogen loss was reduced by 71.93%. The combined treatment did not increase the emission of VSCs. The application of sulphur and T. thioparus 1904 may help to control the odour of compost. Copyright © 2017. Published by Elsevier Ltd.

  2. Hepatobiliary scintigraphy with 99Tcsup(m)-HIDA and 99Tcsup(m)-sulphur colloid

    International Nuclear Information System (INIS)

    Pedersen, S.A.; Oster-Jorgensen, E.; Schoubye, J.; Odense Univ.

    1980-01-01

    The results of a study comparing the ability of 99 Tcsup(m)-sulphur colloid and 99 Tcsup(m)- HIDA to demonstrate circumsribed defects and obstruction of the biliary flow to the intestines are reported. As regards focal liver diseases, colloid scintigraphy (SC) had a nosographic sensitivity and specificity of 0.87 and 0.85, respectively. The corresponding figures for the HIDA scintigraphy were 0.40 and 0.92. Concerning the diagnosis of extrahepatic obstrtuction, sulphur colloid scintigraphy had a nosographic sensitivity and specificity of 0.31 and 0.94. The corresponding figures for HIDA scintigraphy were 0.69 and 0.84. The most frequent cause of false results was pattern of hepatocellular disease in sulphur colloid scans in patients with a longstanding biliary onbstruction. The second most frequent error was due to circumscribed defects in SC as well as in HIDA scans in patients with obstructive diseases and a high value of serum bilirubin. A third source of error was the pattern of an obstruction in HIDA scans in patients with focal diseases. The significance of the star pattern the sulphur colloid scan in patients with obstruction is stressed, as the significance of this pattern not has been evaluated previously. It is concluded that the two different scintigraphic methods are complementary tools in the examination of patients with liver diseases. (orig.) [de

  3. Pore development in anodic alumina in sulphuric acid and borax electrolytes

    International Nuclear Information System (INIS)

    Garcia-Vergara, S.J.; Skeldon, P.; Thompson, G.E.; Habakaki, H.

    2007-01-01

    The formation of porous anodic films on an Al-3.5 at.%W alloy is compared in sulphuric acid and borax electrolytes in order to investigate pore development processes. The findings disclose that for anodizing in sulphuric acid, the pores develop mainly due to the influences of field-induced plasticity of the film and growth stresses; in borax, field-assisted dissolution dominates. The films formed in sulphuric acid are consequently much thicker than the layer of oxidized alloy and tungsten species are retained in the film. In contrast, with borax, the films and oxidized alloy layers are of similar thickness and tungsten species are lost to the electrolyte. Efficiencies of film growth are also significantly different, about 65% in sulphuric acid and about 52% in borax. The retention of tungsten species during anodizing in sulphuric acid is due to the localization of tungsten in the inner regions of the barrier layer and cell walls, with a layer of anodic alumina separating the tungsten-containing regions from the electrolyte. For borax, the tungsten is distributed more uniformly through the film material, enabling loss of tungsten species to the electrolyte from the pore base

  4. Evaluation of the protein concentration in enzymes via the determination of sulphur by TXRF

    International Nuclear Information System (INIS)

    Mertens, M.; Rittmeyer, C.; Kolbesen, B.O.

    2000-01-01

    Total reflection x-ray fluorescence spectrometry (TXRF) offers many advantages for the identification of trace elements in biological samples like enzymes, tissues or plants. Without any preliminary treatment elements may be determined with high accuracy especially transition metals like Fe, Ni, Cu, Mo and the alkaline earth metal Ca. A further aspect of the investigation of enzymes is the simple and simultaneous determination of light elements. Especially sulphur is of interest. The element sulphur exists mainly in the two amino, acids methionine and cysteine as well as in iron-sulphur clusters and may be used for an easy and simultaneous calculation of the protein concentration. Hence the quantitative determination of sulphur by TXRF allows a cross-check regarding of the conventional quantitative determination of protein concentration by, for example, the Lowry method. On the basis of three enzymes of different origins and molecular weights the presentation will show the influence of the bio-organic matrix and different buffer media on element determination by TXRF. As is already known the influence of the matrix on the detection of light elements is stronger than on transition metals. It can be discussed whether layer thickness and layer effects of the drying residues (characterization by SEM and thickness profilometer (ALPHA-step)) and / or self absorption effects as well as the excitation are of significance. The results indicate that with enzymes of low molecular weight a reliable determination of sulphur is possible whereas those with higher molecular weights gave poorer results on account of the matrix effects described. (author)

  5. Sulphur loading of respirable and inhalable dust at a platinum smelter / Swanepoel J.D.

    OpenAIRE

    Swanepoel, Johannes Deon.

    2012-01-01

    The contribution that sulphur, in the form of sulphates, has on ill health is still a focal point of many a study, especially in environmental studies depicting the effects that particulate air pollution has on health. Although the implication of sulphur on particulate matter is not yet well defined, numerous studies do state that the presence of sulphur on particulate matter contributes to poor health. Sulphur adhered to dust has been associated with cardiovascular mortality and the ability ...

  6. An isotope view on ionising radiation as a source of sulphuric acid

    DEFF Research Database (Denmark)

    Enghoff, Martin Andreas Bødker; Bork, Nicolai Christian; Hattori, S.

    2012-01-01

    Sulphuric acid is an important factor in aerosol nucleation and growth. It has been shown that ions enhance the formation of sulphuric acid aerosols, but the exact mechanism has remained undetermined. Furthermore some studies have found a deficiency in the sulphuric acid budget, suggesting a miss...... yields of the experiments, suggests a mechanism in which ionising radiation may lead to hydrated ion clusters that serve as nanoreactors for S(IV) to S(VI) conversion....

  7. An isotopic analysis of ionising radiation as a source of sulphuric acid

    DEFF Research Database (Denmark)

    Enghoff, Martin Andreas Bødker; Bork, Nicolai Christian; Hattori, S.

    2012-01-01

    Sulphuric acid is an important factor in aerosol nucleation and growth. It has been shown that ions enhance the formation of sulphuric acid aerosols, but the exact mechanism has remained undetermined. Furthermore some studies have found a deficiency in the sulphuric acid budget, suggesting a miss...... of the experiments, suggests a mechanism in which ionising radiation may lead to hydrated ion clusters that serve as nanoreactors for S(IV) to S(VI) conversion....

  8. Muonium states and dynamics in phosphorus and sulphur

    International Nuclear Information System (INIS)

    Cox, S.F.J.; Cottrell, S.P.; Hopkins, G.A.; Kay, M.; Pratt, F.L.

    1997-01-01

    The various states formed by positive muons implanted into phosphorus and sulphur have been characterized as a model for interstitial hydrogen, of which little is known in these elements. Repolarization studies reveal muonium-like states in each case, giving estimates of the hyperfine parameters and, for sulphur at least, an indication of the coexistence of a molecular radical state. The longitudinal-field relaxation functions suggest conversion of the paramagnetic states to diamagnetic, i.e. ionization or chemical reaction, in competition with strong spin-lattice relaxation

  9. Sulphur levels in saliva as an estimation of sulphur status in cattle: a validation study

    NARCIS (Netherlands)

    Dermauw, V.; Froidmont, E.; Dijkstra, J.; Boever, de J.L.; Vyverman, W.; Debeer, A.E.; Janssens, G.P.J.

    2012-01-01

    Effective assessment of sulphur (S) status in cattle is important for optimal health, yet remains difficult. Rumen fluid S concentrations are preferred, but difficult to sample under practical conditions. This study aimed to evaluate salivary S concentration as estimator of S status in cattle.

  10. Galactic evolution of sulphur as traced by globular clusters

    Science.gov (United States)

    Kacharov, N.; Koch, A.; Caffau, E.; Sbordone, L.

    2015-05-01

    Context. Sulphur is an important volatile α element, but its role in the Galactic chemical evolution is still uncertain, and more observations constraining the sulphur abundance in stellar photospheres are required. Aims: We derive the sulphur abundances in red giant branch (RGB) stars in three Galactic halo globular clusters (GC) that cover a wide metallicity range (-2.3 noise (S/N ~ 200 per px) spectra in the region of the S I multiplet 3 at 1045 nm for 15 GC stars selected from the literature (six stars in M 4,six stars in M 22, and three stars in M 30). Multiplet 3 is better suited for S abundance derivation than the more commonly used lines of multiplet 1 at 920 nm, since its lines are not blended by telluric absorption or other stellar features at low metallicity. Results: We used spectral synthesis to derive the [S/Fe] ratio of the stars assuming local thermodynamic equilibrium (LTE). We find mean [S/Fe]LTE = 0.58 ± 0.01 ± 0.20 dex (statistical and systematic error) for M 4, [S/Fe]LTE = 0.57 ± 0.01 ± 0.19 dex for M 22, and [S/Fe]LTE = 0.55 ± 0.02 ± 0.16 dex for M 30. The negative NLTE corrections are estimated to be in the order of the systematic uncertainties. We do not detect star-to-star variations of the S abundance in any of the observed GCs, with the possible exception of two individual stars, one in M 22 and one in M 30, which appear to be highly enriched in S. Conclusions: With the tentative exception of two stars with measured high S abundances, we conclude that sulphur behaves like a typical α element in the studied Galactic GCs, showing enhanced abundances with respect to the solar value at metallicities below [Fe/H]-1.0 dex without a considerable spread. Based on observations made with ESO telescopes at the La Silla Paranal Observatory under programmes ID 091.B-0171(A).The reduced spectra and the best fit synthetic models are available at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (ftp://130.79.128.5) or via http

  11. Effects of geothermal energy utilization on stream biota and water quality at The Geysers, California. Final report. [Big Sulphur, Little Sulphur, Squaw, and Pieta Creeks

    Energy Technology Data Exchange (ETDEWEB)

    LeGore, R.S.

    1975-01-01

    The discussion is presented under the following section headings: biological studies, including fish, insects, and microbiology; stream hydrology; stream water quality, including methods and results; the contribution of tributaries to Big Sulphur Creek, including methods, results, and tributary characterization; standing water at wellheads; steam condensate quality; accidental discharges; trout spawning bed quality; major conclusions; list of references; and appendices. It is concluded that present operational practices at Geysers geothermal field do not harm the biological resources in adjacent streams. The only effects of geothermal development observed during the study were related to operational accidents. (JGB)

  12. 78 FR 64526 - Information Collection Activities: Sulphur Operations; Submitted for Office of Management and...

    Science.gov (United States)

    2013-10-29

    ...: Sulphur Operations; Submitted for Office of Management and Budget (OMB) Review; Comment Request ACTION: 30... paperwork requirements in the regulations under Subpart P, Sulphur Operations. This notice also provides the..., Currently Under Review). SUPPLEMENTARY INFORMATION: Title: 30 CFR 250, Subpart P, Sulphur Operations. OMB...

  13. An analytical procedure for determination of sulphur species and isotopes in boreal acid sulphate soils and sediments

    Directory of Open Access Journals (Sweden)

    K. BACKLUND

    2008-12-01

    Full Text Available An analytical scheme suitable for boreal acid sulphate (AS soils and sediments was developed on the basis of existing methods. The presented procedure can be used to quantify and discriminate among acid volatile sulphide, cold chromium reducible sulphur, hot chromium reducible sulphur, elemental sulphur, sulphate sulphur, organic sulphur, total reducible sulphur and total sulphur. The sulphur fractions are recovered as either Ag2S or BaSO4 precipitates and can further be used for isotope analysis. Overlaps between sulphur species are common during speciation, and must be minimized. Some of these overlaps are caused by poor sampling and storage, inappropriate conditions during the distillation, or natural variations in the sample (e.g. Fe3+ interference and grain size. The procedural impact was determined by conducting tests on both artificial and natural samples containing one or several sulphur species. The method is applied on reduced sediment from an AS soil locality (Överpurmo and a brackish lake (Larsmo Lake in western Finland and the results, including S-isotopes, are discussed.;

  14. Mesoporous titanium-manganese dioxide for sulphur mustard and soman decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Stengl, Vaclav, E-mail: stengl@iic.cas.cz [Department of Solid State Chemistry, Institute of Inorganic Chemistry AS CR v.v.i., 250 68 Rez (Czech Republic); Bludska, Jana [Department of Solid State Chemistry, Institute of Inorganic Chemistry AS CR v.v.i., 250 68 Rez (Czech Republic); Oplustil, Frantisek; Nemec, Tomas [Military Technical Institute of Protection Brno, Veslarska 230, 628 00 Brno (Czech Republic)

    2011-11-15

    Highlights: {yields} New nano-dispersive materials for warfare agents decontamination. {yields} 95% decontamination activities for sulphur mustard. {yields} New materials base on titanium and manganese oxides. -- Abstract: Titanium(IV)-manganese(IV) nano-dispersed oxides were prepared by a homogeneous hydrolysis of potassium permanganate and titanium(IV) oxo-sulphate with 2-chloroacetamide. Synthesised samples were characterised using Brunauer-Emmett-Teller (BET) surface area and Barrett-Joiner-Halenda porosity (BJH), X-ray diffraction (XRD), infrared spectroscopy (IR), and scanning electron microscopy (SEM). These oxides were taken for an experimental evaluation of their reactivity with sulphur mustard (HD or bis(2-chloroethyl)sulphide) and soman (GD or (3,3'-dimethylbutan-2-yl)-methylphosphonofluoridate). Mn{sup 4+} content affects the decontamination activity; with increasing Mn{sup 4+} content the activity increases for sulphur mustard and decreases for soman. The best decontamination activities for sulphur mustard and soman were observed for samples TiMn{sub 3}7 with 18.6 wt.% Mn and TiMn{sub 5} with 2.1 wt.% Mn, respectively.

  15. Effect of both sulphur content and deoxidation degree on the hot ductility of resulphurized austenitic stainless steels in the solidified state

    International Nuclear Information System (INIS)

    Botella, J.; Sanchez, R.

    1998-01-01

    The manufacture of free machining austenitic stainless steels features a specific drawback derived from their high sulphur content, which is needed for generating, into the austenitic matrix inclusions to optimize the different machining operations. However, sulphur has ahamfull effect on hot workability. This paper deals with assessing the effect of sulphur content and deoxidation level on the hot ductility of resulphurized austenitic stainless steels in as cast condition. Hot tensile tests were conducted on a Gleeble machine, at temperatures between 1,150 and 1,250 degree celsius, studying a suctility factor as a function of sulphur content, deoxidation degree, as well as type, size and distribution of sulfides. Results point out the harmful effect of increasing sulphur and oxygen contents on the hot workability of resulphurized austenitic stainless steels, and the need to control carefully the level of oxides of these steels. (Author) 5 refs

  16. Reduction of Sulphur Content of Urals Crude Oil Prior to Processing ...

    African Journals Online (AJOL)

    The presence of sulphur in crude oil poses enormous challenges as regards its negative environmental and economic impacts. As such, the safety of the personnel and the equipment is at high risk during the processing of Urals crude oil in Kaduna Refining and Petrochemical Company (KRPC) because of its sour nature.

  17. Sulphur isotope variations in the mantle from ion microprobe analyses of micro-sulphide inclusions

    International Nuclear Information System (INIS)

    Chaussidon, M.; Albarede, F.; Sheppard, S.M.F.

    1989-01-01

    21 samples of sulphide trapped either as liquid globules or grains in various minerals (olivine, pyroxenes, ilmenite and garnet) or rocks (basalt glasses, peridotites, eclogites and kimberlites) of mantle origin, have been analysed for their sulphur isotope, and their Cu, Ni, Fe compositions by ion microprobe. The results show a wide range of δ 34 S values between -4.9±1 and +8±1per mille. Sulphides with high nickel contents (up to 40% pentlandite), corresponding mostly to residual peridotites, have δ 34 S values ranging from -3.2per mille to +3.6per mille with a mode of +3±1per mille, compared to low Ni content sulphides, mostly contained in pyroxenites, OIB and kimberlites, ranging from -3.6per mille to +8per mille with a mode of +1±1per mille. The δ 34 S of sulphides originating from within the mantle are variable. The sulphide globules with high Ni contents and δ 34 S values close to +3per mille, are probably produced by 10-20% partial melting of a mantle source containing 300 ppm sulphur as an upper limit and having a δ 34 S value of +0.5±0.5per mille. This difference in δ 34 S values suggests a high-temperature S-isotope fractionation of ≅+3per mille between liquid sulphide and the sulphur dissolved in the silicate liquid. The sulphur isotopes balance in the system upper mantle + oceanic crust + continental crust + seawater requires a mean δ 34 S value of the primitive upper mantle of +0.5per mille, slightly but significantly different from that of chondrites (+0.2±0.2per mille). (orig.)

  18. Intensification of zinc dissolution process in sulphuric acid

    Directory of Open Access Journals (Sweden)

    Stanojević D.

    2005-01-01

    Full Text Available Many high purity salts are produced by dissolving pure metal in non-oxidizing mineral acids. If hydrogen overpotential on the given metal is high, then the rate of overall process is defined by reaction of hydrogen ion reduction. This study investigated the possibility of accelerated dissolving of metal zinc in sulphuric acid by introducing copper cathode on which evolving hydrogen is much easier than on zinc. It was found out that the acceleration of zinc dissolving is possible and, at constant surface of copper cathode depends on the quality of electrical contact between copper electrode and zinc.

  19. Synergistic inhibition between o-phenanthroline and chloride ion for steel corrosion in sulphuric acid

    International Nuclear Information System (INIS)

    Li Xueming; Tang Libin; Li Lin; Mu Guannan; Liu Guangheng

    2006-01-01

    The corrosion inhibition of cold rolled steel in 0.5 M sulphuric acid in the presence of o-phenanthroline and sodium chloride (NaCl) has been investigated by using weight loss and electrochemical techniques. The experimental data suggest that the inhibition efficiency increases with increasing NaCl concentration in the presence of 0.0002 M o-phenanthroline, but decreases with increasing temperature. A synergistic effect is observed when o-phenanthroline and chloride ions are used together to prevent cold rolled steel corrosion in 0.5 M sulphuric acid. The polarization curves showed that the complex of o-phenanthroline and NaCl acts as a mixed type inhibitor. The experimental results suggested that the presence of chloride ions in the solution stabilized the adsorption of o-phenanthroline molecules on the metal surface and improved the inhibition efficiency of o-phenanthroline. The adsorption of the complex accords with the Langmuir adsorption isotherm. Some thermodynamic parameters such as adsorption heat, adsorption entropy and adsorption free energy have been calculated by employing thermodynamic equations. Kinetic parameters such as apparent activation energy and pre-exponential factor have been calculated and discussed

  20. Leaching of basic oxygen furnace sludge with sulphuric acid

    Directory of Open Access Journals (Sweden)

    Andrea Miškufová

    2010-03-01

    Full Text Available In this study the hydrometallurgical processing of BOF sludge in the sulphuric acid solutions under atmospheric pressureand temperatures up to 100 °C is investigated on a laboratory scale. The influence of sulphuric acid concentration, temperature, timeand liquid to solid ratio (L:S on the leaching process was studied. The main aim of this study was to determine optimal conditions whenthe maximum amount of zinc passes into the solution.

  1. Sulphur management in onion (Allium cepa) cultivation in hills of Himachal Pradesh.

    Science.gov (United States)

    Jaggi, R C; Sharma, R K

    2010-05-01

    Field experiment were conducted at CSK HPKV Research Farm, Palampur during Rabi seasons of 2000-01 and 2001-02, to study the response of onion (Allium cepa var Patna red) at four sulphur levels (0, 15, 30 and 60 kg ha(-1)) applied through Gypsum and S95. The analysis was done to allocate the limited availability of sulphur for maximizing net profit over fertilizer cost. The results show that the dose of sulphur under its full availability is 43.02 kg ha(-1). But under its scarce availability the maximum benefit would occur when it is applied up to 32.11 kg ha(-1) followed by even distribution of fertilizer i.e. 20 kg ha(-1). The returns following sulphur application at these rates, would be Rs 69340, 73092 and 68700 ha(-1) respectively.

  2. An approach for degradation of grape seed and skin proanthocyanidin polymers into oligomers by sulphurous acid.

    Science.gov (United States)

    Luo, Lanxin; Cui, Yan; Cheng, Jinhui; Fang, Bairui; Wei, Zongmin; Sun, Baoshan

    2018-08-01

    To develop an efficient method for degradation of grape seed and skin proanthocyanidins polymers into oligomers, an optimized sulphurous acid degradation conditions for grape seed with the temperature of 60 °C, reaction time of 60 min and sample-sulphurous acid ratio of 1:0.2, and for grape skin with the temperature of 40 °C, reaction time of 60 min and sample-sulphurous acid ratio of 1:0.2, were established. Afterwards, HSCCC and prep-HPLC were used to fractionate and isolate individual proanthocyanidin oligomers from the degradation products. Total of ten dimeric or trimeric procyanidins were obtained, and most of them presented high yield (from 0.7 mg to 13.6 mg per run in grape seed and from 0.5 mg to 4.1 mg per run in grape skin) and high purity (over 90%). The proposed method provides a new way for large preparation of oligomeric proanthocyanidins from naturally abundant and wasted polymeric ones. Copyright © 2018 Elsevier Ltd. All rights reserved.

  3. Integrated sulphur management : gas, oil sands, reclamation and the challenges of fluctuating demand

    International Nuclear Information System (INIS)

    Pineau, R.

    2009-01-01

    International Commodities Export Corporation is a privately held company that provides fully integrated service offerings to add maximum value in designing, building, owning, and operating sulphur assets. The company also offers in-house, engineering, procurement and project management, as well as supply management, transportation and distribution services. It also has expertise in marine transportation. This presentation discussed integrated sulphur management, with particular focus on gas, oil sands, reclamation and the challenges of fluctuating demand. The presentation provided an overview of the sulphur market and oil sands sulphur. Key considerations for oil sands producers were also presented. The challenges of fluctuating demand include price and volume considerations; logistics; geography and distance to market; export/offshore versus domestic/United States; seasonal considerations; and an inelastic sulphur market. The presentation concluded with a status update of ICEC's initiative and the advantages of Prince Rupert, an economically viable export infrastructure to producers without onsite forming facilities. figs

  4. Mercury and sulphur among the High Medieval alchemists: from Rāzī and Avicenna to Albertus Magnus and pseudo-Roger Bacon.

    Science.gov (United States)

    Newman, William R

    2014-11-01

    This essay challenges the often expressed view that the principles of metals, namely mercury and sulphur, were generally viewed by alchemists as being of a 'metaphysical' character that made them inaccessible to the tools and operations of the laboratory. By examining a number of Arabo-Latin and Latin alchemical texts in circulation before the end of the thirteenth century, the author presents evidence that most alchemists of the period considered mercury and sulphur to be materials subject to techniques of purification in the same way that naturally occurring salts and minerals could be freed of their impurities or dross. The article also points to the immense influence of Avicenna and Albertus Magnus in formulating the theory that mercury and sulphur were compounds of different materials, containing both fixed and unfixed components. Finally, the author briefly examines the relationship between this materialist approach to the principles and the chymical atomism of early modern authors who were deeply aware of medieval alchemical literature.

  5. Master curves for the sulphur assisted crosslinking reaction of natural rubber in the presence of nano- and nano-structured sp2 carbon allotropes

    Directory of Open Access Journals (Sweden)

    S. Musto

    2017-06-01

    Full Text Available In this paper, master curves are reported for the crosslinking of a diene rubber with a sulphur based system in the presence of either nano- or nano-structured carbon allotropes, such as carbon nanotubes (CNT, a nanosized graphite with high surface area (HSAG and carbon black (CB. Poly(1,4-cis-isoprene from Hevea Brasiliensis was the diene rubber and crosslinking was performed in temperatures ranging from 151 to 180 °C, with carbon allotropes below and above their percolation threshold. Such carbon allotropes were characterized by different aspect ratio, surface area and pH. However, in the crosslinking reaction, they revealed common behaviour. In fact, the specific interfacial area could be used to correlate crosslinking parameters, such as induction time (ts1 and activation energy (Ea calculated by applying the autocatalytic model. Monotonous decrease of ts1 and increase of Ea were observed, with points lying on master curves, regardless of the nature of the carbon allotropes. Remarkable differences were however observed in the structure of the crosslinking network: when the carbon allotrope was above the percolation threshold much larger crosslinking density was obtained in the presence of CNT whereas composites based on HSAG became soluble in hydrocarbon solvent, after the reaction with a thiol. Proposed explanation of these results is based on the reactivity of carbon allotropes with sulphur and sulphur based compounds, demonstrated through the reaction of 1-dodecanethiol and sulphur with CNT and HSAG and with a model substrate such as anthracene.

  6. Sulphur removal from used automotive lubricating oil by ionizing radiation

    International Nuclear Information System (INIS)

    Scapin, Marcos Antonio; Duarte, Celina Lopes; Sato, Ivone Mulako

    2007-01-01

    Following the worldwide evolution with the purpose of a higher control of vehicular emissions, the specialists have looked for clean technologies and efficient procedures to make vehicular emissions free of pollutants. Much attention is given to the sulphur concentration in the gasoline, diesel and lubricating oils. The ionizing radiation is a promising technology for the removal of this pollutant when compared to other conventional treatment methods. In this work, the ionizing radiation was used to remove in significant levels the presence of sulphur in automotive motor oil. A 1000 mL sample of used automotive lubricating oil from a gas station was collected. This sample was fractioned and irradiated with 10, 20 50, 100, 200 and 500 kGy doses in a 60 Co irradiator (GAMMACELL-220 - 12 kCi). The 50 and 70% (v/v) of MilliQ water and 30% (v/v) of hydrogen peroxide was used to improve the radiolysis The sulphur element before and after the irradiation was determined by X-ray fluorescence technique (WDXRF) using the Fundamental Parameters Method. The results showed approximately 70% sulphur removal at 500 kGy irradiation dose with 70% (v/v) of MilliQ water addition. (author)

  7. Effect of sulphur fertilisation on yield and quality of white mustard seeds

    Directory of Open Access Journals (Sweden)

    Pavel Ryant

    2009-01-01

    Full Text Available The objective of the present study was to estimate the effect of different forms of sulphur on yields and qualitative parameters of white mustard seeds. This topic was studied in 2004 in the form of a pot trial in a vegetation hall and linked up with an identical experiment with spring wheat conducted in 2003. Besides the control variant not fertilised with sulphur (1 we fertilised the soil with elemental sulphur (2, ammonium sulphate (3 and gypsum (4 and applied foliar dressing of elemental sulphur with bentonite (5. For all variants the nitrogen dose was 0.9 g per pot (0.15 g . kg−1 of soil and for va­riants 2 to 4 it was 1 g of sulphur per pot (0.17 g. kg−1 of soil. Foliar dressing of elemental sulphur (S0 was not applied until the stage of six true leaves in a dose of 10 kg per ha (0.032 g per pot.Significantly higher yields of white mustard seeds were achieved after foliar application of S0 which can be also due to its fungicide action. The variants where gypsum was applied showed the highest average number of branches and pods and also straw yields. After gypsum fertilisation or foliar application of S0 the oil content in the mustard seeds exceeded 25%; this is the minimal content required for the production of good quality mustard. The 1000-seed weight was significantly higher after foliar application of S0. The proportion of seeds greyish on the surface, a sign of mildew, significantly decreased after fertilisation with all forms of sulphur, but most of all after foliar application of S0.Fertilisation with ammonium sulphate reduced the exchangeable soil reaction after harvest. On the other hand gypsum alkalised the soil environment and increased the content of available calcium and water-soluble sulphur. The soil of the variant where foliar dressing of S0 was applied had a higher content of available calcium after harvest. The least amount of available sulphur and phosphorus in the soil was seen after foliar

  8. Investigation of the possibility of binding fly ash particles by elemental sulphur

    Directory of Open Access Journals (Sweden)

    Vidojković V.

    2006-01-01

    Full Text Available Thermal power plants in Serbia use lignite for electrical power production The secondary product of coal combustion is fly ash in the amount of 17%. Fly ash causes the pollution of air, water and soil, and also cause many human, especially lung diseases. Secondary sulphur is a product of crude oil refining. The aim of this study was to investigate the use of sulphur as a bonding material in ultra fine particle agglomeration (smaller than 63 μm in fly ash. The agglomeration should make the ash particles larger and heavy enough to fall without flying fractions. The experiments showed that during the homogenization of the ashes and sulphur from 150 to 170 °C in a reactor with intensive mixing, an amount of 15% sulphur was sufficient to bond particles and cause agglomeration without visible flying fractions.

  9. Transport of metals and sulphur in magmas by flotation of sulphide melt on vapour bubbles

    Science.gov (United States)

    Mungall, J. E.; Brenan, J. M.; Godel, B.; Barnes, S. J.; Gaillard, F.

    2015-03-01

    Emissions of sulphur and metals from magmas in Earth’s shallow crust can have global impacts on human society. Sulphur-bearing gases emitted into the atmosphere during volcanic eruptions affect climate, and metals and sulphur can accumulate in the crust above a magma reservoir to form giant copper and gold ore deposits, as well as massive sulphur anomalies. The volumes of sulphur and metals that accumulate in the crust over time exceed the amounts that could have been derived from an isolated magma reservoir. They are instead thought to come from injections of multiple new batches of vapour- and sulphide-saturated magmas into the existing reservoirs. However, the mechanism for the selective upward transfer of sulphur and metals is poorly understood because their main carrier phase, sulphide melt, is dense and is assumed to settle to the bottoms of magma reservoirs. Here we use laboratory experiments as well as gas-speciation and mass-balance models to show that droplets of sulphide melt can attach to vapour bubbles to form compound drops that float. We demonstrate the feasibility of this mechanism for the upward mobility of sulphide liquids to the shallow crust. Our work provides a mechanism for the atmospheric release of large amounts of sulphur, and contradicts the widely held assumption that dense sulphide liquids rich in sulphur, copper and gold will remain sequestered in the deep crust.

  10. Di- or polysulphide-bound biomarkers in sulphur-rich geomacromolecules as revealed by selective chemolysis

    NARCIS (Netherlands)

    Sinninghe Damsté, J.S.; Kohnen, M.E.L.; Kock-van Dalen, A.C.; Leeuw, J.W. de

    1991-01-01

    Three types of sulphur-rich, high-molecular-weight material in the alkylsulphide, the polar and the asphaltene fracions isolated from the bitumen of an immature bituminous shale from the Vena del Gesso basin (Italy) were desulphurised.

  11. Effect of feedstock end boiling point on product sulphur during ultra deep diesel hydrodesulphurization

    Energy Technology Data Exchange (ETDEWEB)

    Stratiev, D.; Ivanov, A.; Jelyaskova, M. [Lukoil Neftochim Bourgas AD, Bourgas (Bulgaria)

    2004-12-01

    An investigation was carried out to test the feasibility of producing 50 and 10 ppm sulphur diesel in a conventional hydrotreating unit operating at low pressure conditions by varying the feedstock end boiling point. Middle distillate fractions distilled from a mixture of Ural crude oil, reduced crude, vacuum gas oil, naphtha and low sulphur crude oils with 95% vol. points of 274, 359, 343, 333, and 322 C (ASTM D-86 method) and sulphur contents of 0.36, 0.63, 0.99, 0.57, and 0.47%, respectively, were hydrotreated using the Akzo Nobel Stars family Co-Mo KF-757 catalyst in a trickle bed pilot plant at following conditions: reactor inlet temperature range of 320-360 C; liquid hourly space velocity (LHSV) range of 1-2 h{sup -1}; total reactor pressure of 3.5 MPa; treating gas: feedstock ratio of 250 Nm{sup 3}/m{sup 3}. It was found that the determinant factor for the attainment of ultra low sulphur levels during middle distillate hydrodesulphurization was not the total sulphur content in the feed but the content of the material boiling above 340 C (according to TBP). For all LHSVs and reactor inlet temperatures studied the product sulphur dependence on the feed 340 C+ fraction content was approximated by second order power law. The specification of 50 ppm sulphur was achieved with all studied feedstocks. However the 10ppm sulphur limit could be met only by feedstocks with 95% vol. points below 333 C, which is accompanied by about 10% reduction of the diesel potential. The hydrotreatment tests on a blend 80% straight run gas oil (ASTM D-86 95% vol. of 274 C)/20%FCC LCO (ASTM D-86 95% vol. of 284 C) showed product sulphur levels which were not higher than those obtained by hydrotreatment of the straight run gas oil, indicating that undercutting the FCC LCO gives the refiner the opportunity to increase the potential for the production of 10 ppm sulphur diesel at the conditions of the conventional hydrotreating unit operating at low pressure. The product cetane index was

  12. Aspects of using biomass as energy source for power generation

    Directory of Open Access Journals (Sweden)

    Tîrtea Raluca-Nicoleta

    2017-07-01

    Full Text Available Biomass represents an important source of renewable energy in Romania with about 64% of the whole available green energy. Being a priority for the energy sector worldwide, in our country the development stage is poor compared to solar and wind energy. Biomass power plants offer great horizontal economy development, local and regional economic growth with benefic effects on life standard. The paper presents an analysis on biomass to power conversion solutions compared to fossil fuels using two main processes: combustion and gasification. Beside the heating value, which can be considerably higher for fossil fuels compared to biomass, a big difference between fossil fuels and biomass can be observed in the sulphur content. While the biomass sulphur content is between 0 and approximately 1%, the sulphur content of coal can reach 4%. Using coal in power plants requires important investments in installations of flue gas desulfurization. If limestone is used to reduce SO2 emissions, then additional carbon dioxide moles will be released during the production of CaO from CaCO3. Therefore, fossil fuels not only release a high amount of carbon dioxide through burning, but also through the caption of sulphur dioxide, while biomass is considered CO2 neutral. Biomass is in most of the cases represented by residues, so it is a free fuel compared to fossil fuels. The same power plant can be used even if biomass or fossil fuels is used as a feedstock with small differences. The biomass plant could need a drying system due to high moisture content of the biomass, while the coal plant will need a desulfurization installation of flue gas and additional money will be spent with fuel purchasing.

  13. Dispersion of sulphur in the northern hemisphere. A study with a 3-dimensional time-resolved model

    Energy Technology Data Exchange (ETDEWEB)

    Tarrason, L

    1996-12-31

    This thesis on atmospheric dispersion of sulphur presents a calculation of intercontinental transport of oxidized sulphur and allocates different contributions to sulphur background levels over Europe. It is found that a significant fraction of anthropogenic sulphur (AS) is transported out of continental boundaries thus affecting the background levels over major parts of the northern hemisphere. Over Europe, the contribution of AS from North America is similar in amount to that of Asian AS and natural sources from the North Atlantic Ocean. Although the yearly contribution of intercontinental transport to deposition of sulphur over Europe is quite small, it can be much more important over certain areas and seasons and is comparable to the contributions from individual European countries. The calculations are based on a three-dimensional Eulerian time-resolved model that describes sulphur dispersion in the atmosphere in connection with large-scale synoptic flows and agree well with observations. The thesis emphasizes the role of synoptic scale atmospheric motions in determining intercontinental transport of sulphur. It indicates the need to resolve individual cyclones and anticyclones in order to describe the dispersion and distribution of atmospheric sulphur in the northern hemisphere and stresses the value of comparing model calculations with observations, both in atmospheric chemistry studies and in climate applications. 260 refs., 50 figs., 17 tabs.

  14. Dispersion of sulphur in the northern hemisphere. A study with a 3-dimensional time-resolved model

    Energy Technology Data Exchange (ETDEWEB)

    Tarrason, L.

    1995-12-31

    This thesis on atmospheric dispersion of sulphur presents a calculation of intercontinental transport of oxidized sulphur and allocates different contributions to sulphur background levels over Europe. It is found that a significant fraction of anthropogenic sulphur (AS) is transported out of continental boundaries thus affecting the background levels over major parts of the northern hemisphere. Over Europe, the contribution of AS from North America is similar in amount to that of Asian AS and natural sources from the North Atlantic Ocean. Although the yearly contribution of intercontinental transport to deposition of sulphur over Europe is quite small, it can be much more important over certain areas and seasons and is comparable to the contributions from individual European countries. The calculations are based on a three-dimensional Eulerian time-resolved model that describes sulphur dispersion in the atmosphere in connection with large-scale synoptic flows and agree well with observations. The thesis emphasizes the role of synoptic scale atmospheric motions in determining intercontinental transport of sulphur. It indicates the need to resolve individual cyclones and anticyclones in order to describe the dispersion and distribution of atmospheric sulphur in the northern hemisphere and stresses the value of comparing model calculations with observations, both in atmospheric chemistry studies and in climate applications. 260 refs., 50 figs., 17 tabs.

  15. Sulphur Mustard Poisoning and Its Complications in Iranian Veterans

    Directory of Open Access Journals (Sweden)

    Beeta Balali-Mood

    2009-09-01

    Full Text Available Sulphur mustard is a chemical warfare agent, which was largelyused during the World War One and in Iraq-Iran conflict. It mayalso be used as a chemical terrorism agent. Therefore, medicalprofessions should have sufficient knowledge and be preparedfor medical intervention of any such chemical attack.Sulphur mustard exerts direct toxic effects on the eyes, skin,and respiratory tract, with subsequent systemic actions on thenervous, immunologic, hematologic, digestive, and reproductivesystems. It is an alkylating agent that affects DNA synthesis andthus, delayed complications have been considered since theWorld War One. Cases of malignancies in the target organs particularlyin hematopoietic, respiratory, and digestive systemswere reported. Common delayed respiratory complications includechronic bronchitis, bronchiectasis, frequent bronchopneumonia,and pulmonary fibrosis, all of which tend to deterioratewith time. Severe dry skin, delayed keratitis, and reduction ofnatural killer cells with subsequent increased risk of infectionsand malignancies are also among the most distressing long-termconsequences of sulphur mustard intoxication. However, despiteextensive research that has been conducted on Iranian veteransduring the past decades, major gaps continue to remain in thesulphur mustard literature. Immunological and neurological dysfunctionsand the relationship between exposure to sulphur mustardand mutagenicity, carcinogenicity, and teratogenicity areimportant fields that require further studies, particularly on Iranianveterans with chronic health problems caused by sulphurmustard poisoning. There is also a paucity of information on themedical management of acute and delayed toxic effects of sulphurmustard poisoning, a subject that greatly challenges themedical professions.

  16. Application of sulphur isotope ratios to examine weaning patterns and freshwater fish consumption in Roman Oxfordshire, UK

    Science.gov (United States)

    Nehlich, Olaf; Fuller, Benjamin T.; Jay, Mandy; Mora, Alice; Nicholson, Rebecca A.; Smith, Colin I.; Richards, Michael P.

    2011-09-01

    This study investigates the application of sulphur isotope ratios (δ 34S) in combination with carbon (δ 13C) and nitrogen (δ 15N) ratios to understand the influence of environmental sulphur on the isotopic composition of archaeological human and faunal remains from Roman era sites in Oxfordshire, UK. Humans ( n = 83), terrestrial animals ( n = 11), and freshwater fish ( n = 5) were analysed for their isotope values from four locations in the Thames River Valley, and a broad range of δ 34S values were found. The δ 34S values from the terrestrial animals were highly variable (-13.6‰ to +0.5‰), but the δ 34S values of the fish were clustered and 34S-depleted (-20.9‰ to -17.3‰). The results of the faunal remains suggest that riverine sulphur influenced the terrestrial sulphur isotopic signatures. Terrestrial animals were possibly raised on the floodplains of the River Thames, where highly 34S-depleted sulphur influenced the soil. The humans show the largest range of δ 34S values (-18.8‰ to +9.6‰) from any archaeological context to date. No differences in δ 34S values were found between the males (-7.8 ± 6.0‰) and females (-5.3 ± 6.8‰), but the females had a linear correlation ( R2 = 0.71; p eating solely terrestrial protein resources and others showing a diet almost exclusively based on freshwater protein such as fish. Such large dietary variability was not visible by analysing only the carbon and nitrogen isotope ratios, and this research represents the largest and most detailed application of δ 34S analysis to examine dietary practices (including breastfeeding and weaning patterns) during the Romano-British Period.

  17. Growth and yield response of sunflower (helianthus annuus l.) to sulphur and boron application

    International Nuclear Information System (INIS)

    Tahir, M.; Shah, S.A.; Tanveer, A.; Rehman, H.U.

    2014-01-01

    An experiment was conducted to study the growth and yield response of sunflower to sulphur and boron application. Sulphur (control, 15, 30 kg/ha) and foliar sprays of 1% boron solution (control, spray at 4 week after emergence, 20 days after first spray, at 4 weeks after germination + 20 days after first spray) was applied in soil. The results showed significant increase of all growth and yield parameters by varying levels of sulphur and boron application. Application of 30 kg sulphur/ha enhanced stem diameter (1.99 cm), number of achene per head (765.75) and oil content (36.42%). In case of combined use of sulphur and boron application, maximum plant height (171 cm), head diameter (20.71 cm), 1000-achene weight (54.56 g), biological yield (16.49 t/ha) and achene yield (3.99 t/ha) was recorded by the application of 2 sprays of boron solution (1%) at 4 weeks after germination and reproductive stage. (author)

  18. Use of PSA for design of emergency mitigation systems in a hydrogen production plant using General Atomics SI cycle technology. Section 2: Sulphuric acid decomposition

    International Nuclear Information System (INIS)

    Mendoza, A.; Nelson, P.F.; Francois, J.L.

    2010-01-01

    Throughout the past decades, the need to reduce greenhouse gas emissions has prompted the development of technologies for the production of clean fuels through the use of zero emissions primary energy resources, such as heat from high temperature nuclear reactors. One of the most promising of these technologies is the generation of hydrogen by the sulphur-iodine cycle coupled to a high temperature nuclear reactor, initially proposed by General Atomics. By its nature and because these will have to be large-scale plants, development of these technologies from its current phase to its procurement and construction phase, will have to incorporate emergency mitigation systems in all its sections and nuclear-chemical 'tie-in points' to prevent unwanted events that can compromise the integrity of the plant and the nearby population centres. For the particular case of the SI thermochemical cycle, a large number of safety studies have been developed; however, most of these studies have focused on hydrogen explosions and failures in the primary cooling system. While these are the most catastrophic events, it is also true that there are many other events that without having a direct impact on the nuclear-chemical coupling, could jeopardise plant operations, safety of people in nearby communities and bring economic consequences. This study examined one of these events, which is the formation of a toxic cloud driven by an uncontrolled leakage of concentrated sulphuric acid in the second section of the General Atomics SI cycle. In this section, the concentration of sulphuric acid is close to 90% in conditions of high temperature and positive pressure. Under these conditions, sulphuric acid and sulphur oxides from the reactor would immediately form a toxic cloud, that in contact with operators could cause fatalities, or could produce choking, respiratory problems and eye irritation to people in neighbouring towns. The methodology used for this analysis is the design based on

  19. Implantation induced electrical isolation of sulphur doped GaN xAs1-x layers

    International Nuclear Information System (INIS)

    Ahmed, S.; Lin, J.; Haq, A.; Sealy, B.

    2005-01-01

    The study of III-N-V semiconductor alloys, especially GaN x As 1-x has been increasing in the last few years. The strong dependence of the band gap on the nitrogen content has made this material important for a variety of applications, including long wavelength optoelectronic devices and high efficiency solar cells. We report on the effects of sulphur doping implants on the achieved electrical isolation in GaN x As 1-x layers using proton bombardment. Sulphur ions were implanted in MOCVD-grown GaN x As 1-x layers (1.4 μm thick with nominal x = 1%) with multiple energies creating approximately uniform doping profiles in the range of about 1 x 10 18 -5 x 10 19 cm -3 . Several proton implants were performed in order to find the threshold dose (minimum dose to achieve maximum sheet resistivity) for the electrical isolation of n-type GaN x As 1-x layers. Results show that the sheet resistance of n-type layers can be increased by about five orders of magnitude by proton implantation and the threshold dose to convert a conductive layer to a highly resistive one depends on the original free carrier concentration. The study of annealing temperature dependence of sheet resistivity in proton-isolated GaN x As 1-x layers shows that the electrical isolation can be preserved up to 450 and 500 deg. C when the implantation is performed at RT and 77 K with threshold dose, respectively. These results for n-type GaN x As 1-x layers are novel and have ramifications for device engineers

  20. Sulphur isotopes in a metamorphogenic gold deposit, Macraes mine, Otago Schist, New Zealand

    International Nuclear Information System (INIS)

    Craw, D.; Hall, A.J.; Fallick, A.E.; Boyce, A.J.

    1995-01-01

    The Macraes gold quartz vein deposit, New Zealand, is located in a shear zone cutting greenschist facies metasediments of the Otago Schist. The deposit has been interpreted as being metamorphogenic in origin as there is no evidence for coeval magmatic activity in the Otago Schist orogen. The immediate host rock at the Macraes deposit is pyritic (δ 34 S = -2.7 to -1.3 per mil ) and locally weakly graphitic schist, a rare rock type in the Otago Schist. Sulphur isotope analyses of pyrite and arsenopyrite extracts from auriferous veins and wall-rock schist provide a similar narrow range in δ 34 S values, from -3.0 to -1.0 per mil (n=9). The lack of isotopically depleted sulphur, the narrow range in values, and the replacement sulphide textures help discount a primary bacteriogenic origin for host-rock sulphide. Sulphide in both veins and wall rock is of hydrothermal origin. Sulphides in metasediments and metavolcanics elsewhere in the Otago Schist have δ 34 S in the narrow range -6 to +6 per mil. The sulphur isotope data are consistent with origin of hydrothermal sulphur within the metamorphic pile but provide no constraint on specific rock types which contributed the sulphur to the hydrothermal fluid. The study demonstrates that sulphur isotopic signatures near zero per mil can arise without any direct magmatic input into the mineralisation process. (author). 34 refs., 2 figs., 1 tab

  1. The effect of sulphur-terminated GaAs substrates on the MOVPE growth of CuGaS2 thin films

    International Nuclear Information System (INIS)

    Berndt, P.R.; Botha, J.R.; Branch, M.S.; Leitch, A.W.R.; Kirmse, H.; Neumann, W.; Weber, J.

    2007-01-01

    In this study, various CuGaS 2 layers were grown on GaAs (001) substrates using metalorganic vapour phase epitaxy, for the purpose of studying the effect of sulphur-termination of the substrate on layer quality. The resultant films were investigated using X-ray diffractometry, and transmission electron microscopy, with high-resolution transmission electron microscopy providing additional insights into crystallite growth on the control substrates. This paper will demonstrate that sulphur-termination limits substrate degradation. In the absence of sulphur-termination, atypical three-dimensional MOVPE growth is observed, with epitaxial crystallites varying in size from 10 nm to 200 nm. Substrate degradation inhibits lateral growth at the interface resulting in amorphous regions, cavities, and epitaxial crystallites demonstrating overgrowth into mushroom-like structures

  2. Selective methods for polyphenols and sulphur dioxide determination in wines.

    Science.gov (United States)

    García-Guzmán, Juan J; Hernández-Artiga, María P; Palacios-Ponce de León, Lourdes; Bellido-Milla, Dolores

    2015-09-01

    A critical review to the methods recommended by international bodies and widely used in the winery industry and research studies was performed. A Laccase biosensor was applied to the selective determination of polyphenols in wines. The biosensor response was characterised and it responds mainly to o-diphenols which are the principal polyphenols responsible for the stability and sensory qualities of wines. The spectrophotometric method to determine free and total sulphur dioxide recommended for beers was applied directly to wines. A sampling of 14 red and white wines was performed and they were analysed for biosensor polyphenol index (IBP) and sulphur dioxide concentration (SO2). The antioxidant capacity by the ABTS(+) spectrophotometric method was also determined. A correlation study was performed to elucidate the influence of the polyphenols and SO2 on the wines stability. High correlations were found between IBP and antioxidant capacity and low correlation between SO2 and antioxidant capacity. To evaluate the benefits of wine drinking a new parameter (IBP/SO2) is proposed. Copyright © 2015 Elsevier Ltd. All rights reserved.

  3. Nitrogen and Sulphur Relations in Effecting Yield and Quality of Cereals and Oilseed Crops

    Directory of Open Access Journals (Sweden)

    B.K. Nad

    2001-01-01

    Full Text Available Nitrogen and sulphur, both vital structural elements, are especially needed for the synthesis of proteins and oils. Investigations revealed the required application of sulphur is one half to one third the amount of nitrogen, and the ratio becomes narrower in mustard (Brassica juncea L., followed by wheat and rice. The efficiency of an increased level of nitrogen required a proportionately higher amount of sulphur. A critical investigation on the effective utilization of applied vis-à-vis absorbed nitrogen in wheat and mustard envisaged accumulation of NO3-N in vegetative parts when sulphur remained proportionately low. Application of sulphur hastened the chemical reduction of absorbed NO3– for its effective utilization. The effect was more pronounced in mustard than in wheat. Easily available forms of sulphur, like ammonium sulphate and gypsum, as compared to pyrite or elemental sulphur, maintained adequate N to S ratio in rice, resulting in a reduction in the percent of unfilled grain, a major consideration in rice yield. A narrow N to S ratio, with both at higher levels, increased the oil content but raised the saponification value of the oil, a measure of free fatty acids. Whereas, a proportionately narrow N to S ratio at moderate dose resulted in adequately higher seed and oil yield with relatively low saponification value, associated with increased iodine value of the oil, indicating respectively low free fatty acids and higher proportion of unsaturated fatty acids, an index for better quality of the oil.

  4. The recovery of sulphur, uranium and gold from residues in OFS scheme

    International Nuclear Information System (INIS)

    Ruhmer, W.T.; Botha, F.; Adams, J.S.

    1978-01-01

    This article describes a project comprising three plants for the flotation of pyrite, a twin-stream uranium plant in which high-grade slimes and pyrite can be leached separately, a pyrite burning sulphuric acid plant, and a plant for the recovery of gold from calcines. Details of these plants including capital costs and estimate production are given

  5. Prediction of sulphur content in the industrial hydrotreatment process

    Energy Technology Data Exchange (ETDEWEB)

    Lukec, Ivana; Lukec, Darko [Model d.o.o, Pazinska 36, 10110 Zagreb (Croatia); Sertic-Bionda, Katica [Faculty of Chemical Engineering and Technology, Marulicev trg 19, 10000, Zagreb (Croatia)

    2008-03-15

    The artificial neural network models were developed to determine sulphur content in the hydrotreatment product. Two models for two different types of feed were developed: light gas oil and vacuum gas oil. The developed ANN models use 6 input variables that are continuously measured in the process and are in accordance with the engineering knowledge and thermodynamics of hydrotreatment processes. Given models show good predictability of sulphur content in the hydrotreatment product and are, therefore, used in practice for continuous monitoring and optimization. This kind of application can be easily developed in any other hydrotreatment process with the available adequate historical data. (author)

  6. Waste utilization in electric energy industry

    International Nuclear Information System (INIS)

    Parate, N.S.; Harris, E.

    1991-01-01

    This paper reports that electric energy is an integral element of today's economy and the standard quality of life. The availability of energy at an affordable cost has always been of basic concern because of the intimate relationship of energy to our societal development and progress. Coal and Uranium are the primary alternative energy sources for large electric power plants. Coal remains the dominant fuel for electric generation. The pressurized fluidized bed combustion technology has the potential of utilizing all types of coal, including coal with high ash, high sulphur, and high moisture content. Fluidized bed combustion is a firing technique which fulfills today's pollution control requirements without downstream flue gas cleaning plants like scrubbers, baghouses, and precipitators

  7. Solid state radiolysis of sulphur-containing amino acids. Cysteine, cystine and methionine

    International Nuclear Information System (INIS)

    Franco Cataldo; Pietro Ragni; Susana Iglesias-Groth; Arturo Manchado

    2011-01-01

    The sulphur-containing proteinaceous amino acids l-cysteine, l-cystine and l-methionine were irradiated in the solid state to a dose of 3.2 MGy. This dose corresponds to that delivered by radionuclide decay in a timescale of 1.05 x 10 9 years to the organic matter buried at a depth >20 m in comets and asteroids. The purity of the sulphur-containing amino acids was studied by differential scanning calorimetry (DSC) before and after the solid state radiolysis and the preservation of the chirality after the radiolysis was studied by chirooptical methods (optical rotatory dispersion, ORD) and by FT-IR spectroscopy. Although the high radiation dose of 3.2 MGy delivered, all the amino acids studied show a high radiation resistance. The best radiation resistance was offered by l-cysteine. The radiolysis of l-cysteine leads to the formation of l-cystine. The radiation resistance of l-methionine is not at the level of l-cysteine but also l-methionine is able to survive the dose of 3.2 MGy. Furthermore in all cases examined the preservation of chirality after radiolysis was clearly observed by the ORD spectroscopy although a certain level of radioracemization was measured in all cases. The radioracemization is minimal in the case of l-cysteine and is more pronounced in the case of l-methionine. In conclusion, the study shows that the sulphur-containing amino acids can survive for 1.05 x 10 9 years and, after extrapolation of the data, even to the age of the Solar System i.e. to 4.6 x 10 9 years. (author)

  8. Self-cementitious properties of fly ashes from CFBC boilers co-firing coal and high-sulphur petroleum coke

    International Nuclear Information System (INIS)

    Sheng Guanghong; Li Qin; Zhai Jianping; Li Feihu

    2007-01-01

    Self-cementitious properties of fly ash from circulating fluidized bed combustion boiler co-firing coal and high-sulphur petroleum coke (CPFA) were investigated. CPFA was self-cementitious which was affected by its fineness and chemical compositions, especially the contents of SO 3 and free lime (f-CaO). Higher contents of SO 3 and f-CaO were beneficial to self-cementitious strength; the self-cementitious strength increases with a decrease of its 45 μm sieve residue. The expansive ratio of CPFA hardened paste was high because of generation of ettringite (AFt), which was influenced by its water to binder ratio (W/A), curing style and grinding of the ash. The paste cured in water had the highest expansive ratio, and grinding of CPFA was beneficial to its volume stability. The hydration products of CPFA detected by X-ray diffraction (XRD) and scanning electron microscopy (SEM) were portlandite, gypsum, AFt and hydrated calcium silicate (C-S-H)

  9. Studies on the availability of sulphur in four soil series of soil and water management project, Patiala

    International Nuclear Information System (INIS)

    Sharma, Kesho Ram; Dev, G.

    1974-01-01

    Differential behaviour of four soils series (Banra, Fatehpur, Temple and Samana) for availability of S to wheat (Kalyan-sona) was studied in a pot experiment using five doses of labelled sulphur (0, 5, 10, 20 and 40 kg/ha) applied as (NH 4 ) 2 35 SO 4 . The yield, sulphur content and total removal of sulphur by plant, was found dependent upon sulphur supplying power of the soil, which was confirmed by the radioassay data as well. (author)

  10. Chemical deactivation of Ag/Al2O3 by sulphur for the selective reduction of NOx using hydrocarbons

    International Nuclear Information System (INIS)

    Houel, Valerie; Millington, Paul; Pollington, Stephen; Poulston, Stephen; Rajaram, Raj R.; Tsolakis, Athanasios

    2006-01-01

    The hydrocarbon-SCR activity of Ag/Al 2 O 3 catalysts is severely deactivated after low temperature (350 o C) sulphur ageing in the form of SO 2 exposure. Catalysts aged with SO 2 , NO and hydrocarbon present accumulate a significantly larger amount of SO 4 2- than those aged in the presence of only O 2 , H 2 O and SO 2 when exposed to an equivalent amount of S. Following sulphation of the catalyst most of the sulphur can be removed by a high temperature (600 o C) treatment in the reaction gas. Regeneration in the absence of hydrocarbon is ineffective. The hydrocarbon-SCR activity of the sulphated catalyst using model hydrocarbons such as n-C 8 H 18 can be restored after a high temperature pre-treatment in the reaction gases. However this desulphation process fails to regenerate the hydrocarbon-SCR activity when diesel fuel is used in the activity test. TPR studies show that a major fraction of the sulphur species present in the catalyst is removed by such pre-treatment, but the slight residual amount of sulphur is sufficient to inhibit the activation of the diesel fuel on the Ag catalyst. The nature of the hydrocarbon species present for the hydrocarbon-SCR reaction and during the regeneration strongly influences the activity. In general aromatics such as C 7 H 8 are less effective for reducing NO x and regenerating the sulphated catalyst. (author)

  11. Gamma rays from fast neutron capture in silicon and sulphur

    International Nuclear Information System (INIS)

    Lindholm, A.; Nilsson, L.; Bergqvist, I.

    1975-01-01

    Gamma-ray spectra from neutron capture in natural samples of silicon and sulphur have been recorded at eight neutron energies between 4 and 15 MeV. Time-of-flight techniques were used to improve the signal-to-background ratio and the gamma radiation was detected by a large NaI(Tl) scintillator. Cross sections have been determined for transitions to individual (or groups of) levels in the final nucleus. Calculations based on the direct-semidirect model show that this model gives a reasonable description of the shapes of the gamma-ray spectra, but fails to account for observed excitation functions. The inclusion of the compound-nucleus capture process gives a conclusive improvement in the description of the excitation functions, in particular at low neutron energies. The ability of the compound-nucleus model to account for the shapes of the gamma-ray spectra is as good as that of the direct-semidirect model. At higher neutron energies, an improvement is obtained for transitions to the region of weakly bound levels, where the single-particle structure is poorly known. (Auth.)

  12. The effect of sulphur-terminated GaAs substrates on the MOVPE growth of CuGaS{sub 2} thin films

    Energy Technology Data Exchange (ETDEWEB)

    Berndt, P.R. [Department of Physics, Nelson Mandela Metropolitan University, Port Elizabeth (South Africa)]. E-mail: pearl.berndt@nmmu.ac.za; Botha, J.R. [Department of Physics, Nelson Mandela Metropolitan University, Port Elizabeth (South Africa); Branch, M.S. [Department of Physics, Nelson Mandela Metropolitan University, Port Elizabeth (South Africa); Leitch, A.W.R. [Department of Physics, Nelson Mandela Metropolitan University, Port Elizabeth (South Africa); Kirmse, H. [Institute of Physics, Chair of Crystallography, Humboldt University of Berlin, Berlin (Germany); Neumann, W. [Institute of Physics, Chair of Crystallography, Humboldt University of Berlin, Berlin (Germany); Weber, J. [Institute for Applied Physics-Semiconductor Physics, University of Technology, Dresden (Germany)

    2007-05-31

    In this study, various CuGaS{sub 2} layers were grown on GaAs (001) substrates using metalorganic vapour phase epitaxy, for the purpose of studying the effect of sulphur-termination of the substrate on layer quality. The resultant films were investigated using X-ray diffractometry, and transmission electron microscopy, with high-resolution transmission electron microscopy providing additional insights into crystallite growth on the control substrates. This paper will demonstrate that sulphur-termination limits substrate degradation. In the absence of sulphur-termination, atypical three-dimensional MOVPE growth is observed, with epitaxial crystallites varying in size from 10 nm to 200 nm. Substrate degradation inhibits lateral growth at the interface resulting in amorphous regions, cavities, and epitaxial crystallites demonstrating overgrowth into mushroom-like structures.

  13. Sulphur abundances in halo giants from the [S ı] line at 1082 nm and the [S ı] triplet around 1045 nm

    DEFF Research Database (Denmark)

    Jönsson, H.; Ryde, N.; Nissen, Poul Erik

    2011-01-01

    to clarify this situation by measuring the sulphur abundance in a sample of halo giants using two diagnostics: the S i triplet around 1045 nm and the [S i] line at 1082 nm. The latter of the two is not believed to be sensitive to non-LTE effects. We can thereby minimize the uncertainties in the diagnostic...... used and estimate the usefulness of the triplet for the sulphur determination in halo K giants. We will also be able to compare our sulphur abundance differences from the two diagnostics with the expected non-LTE effects in the 1045 nm triplet previously calculated by others. Methods. High...... diagnostics using tailored 1D model atmospheres and relying on non-LTE corrections from the litterature. Effects of convective inhomogeneities in the stellar atmospheres are investigated. Results. The sulphur abundances derived from both the [S i] line and the non-LTE corrected 1045 nm triplet favor a flat...

  14. Effects of phosphorus, silicon and sulphur on microstructural evolution in austenitic stainless steels during electron irradiation

    International Nuclear Information System (INIS)

    Fukuya, K.; Nakahigashi, S.; Ozaki, S.; Shima, S.

    1991-01-01

    Fe-18Cr-9Ni-1,5Mn austenitic alloys containing phosphorus, silicon and sulphur were irradiated by 1 MeV electrons at 573-773 K. Phosphorus increased the interstitial loop nucleation and decreased the void swelling by increasing void number density and suppressing void growth. Silicon had a similar effect to phosphorus but its effect was weaker than phosphorus. Sulphur enhanced void swelling through increasing the void density. Nickel enrichment at grain boundaries was suppressed only in the alloy containing phosphorus. These phosphorus effects may be explained by a strong interaction with interstitials resulting in a high density of sinks for point defects. (orig.)

  15. The separation of sulphur-35 and phosphorus-32 from urine and their subsequent estimation

    International Nuclear Information System (INIS)

    Kramer, G.H.

    1981-07-01

    A method has been developed that will specifically separate sulphur-35 and phosphorus-32 from urine. Interfering cations are removed by cation exchange and differential precipitation is used to remove the unwanted anion(s). The anion of interest is estimated by liquid scintillation counting and recoveries are 95% for sulphur-35 and 70% for phosphorus-32. The detection limits for sulphur-35 and phosphorus-32 are estimated to be 1.5 pCi and 1.3 pCi, respectively (1 pCi = 37 mBq)

  16. Sulphur-oxidizing and sulphate-reducing communities in Brazilian mangrove sediments.

    Science.gov (United States)

    Varon-Lopez, Maryeimy; Dias, Armando Cavalcante Franco; Fasanella, Cristiane Cipolla; Durrer, Ademir; Melo, Itamar Soares; Kuramae, Eiko Eurya; Andreote, Fernando Dini

    2014-03-01

    Mangrove soils are anaerobic environments rich in sulphate and organic matter. Although the sulphur cycle is one of the major actors in this ecosystem, little is known regarding the sulphur bacteria communities in mangrove soils. We investigated the abundance, composition and diversity of sulphur-oxidizing (SOB) and sulphate-reducing (SRB) bacteria in sediments from three Brazilian mangrove communities: two contaminated, one with oil (OilMgv) and one with urban waste and sludge (AntMgv), and one pristine (PrsMgv). The community structures were assessed using quantitative real-time polymerase chain reaction (qPCR), polymerase chain reaction-denaturing gradient gel electrophoresis (PCR-DGGE) and clone libraries, using genes for the enzymes adenosine-5'-phosphosulphate reductase (aprA) and sulphite reductase (Dsr) (dsrB). The abundance for qPCR showed the ratio dsrB/aprA to be variable among mangroves and higher according to the gradient observed for oil contamination in the OilMgv. The PCR-DGGE patterns analysed by Nonmetric Multidimensional Scaling revealed differences among the structures of the three mangrove communities. The clone libraries showed that Betaproteobacteria, Gammaproteobacteria and Deltaproteobacteria were the most abundant groups associated with sulphur cycling in mangrove sediments. We conclude that the microbial SOB and SRB communities in mangrove soils are different in each mangrove forest and that such microbial communities could possibly be used as a proxy for contamination in mangrove forests. © 2013 John Wiley & Sons Ltd and Society for Applied Microbiology.

  17. Three-dimensional sulphur/nitrogen co-doped reduced graphene oxide as high-performance supercapacitor binder-free electrodes

    Science.gov (United States)

    Huo, Jinghao; Zheng, Peng; Wang, Xiaofei; Guo, Shouwu

    2018-06-01

    Sulphur/nitrogen co-doped reduced graphene oxide (SNG) aerogels were prepared by a simple solvothermal method with l-cysteine-assisted in ethylene glycol. The morphology and composition tests showed that the S/N heteroatoms were evenly distributed on SNG microsheets, and these microsheets were further composed of SNG aerogels with three-dimensional (3D) porous structure. The cyclic voltammetry and galvanostatic charge/discharge tests illustrated the SNG bind-free electrode possessed electric double-layer capacitance and pseudocapacitance, and had a capacitance of 254 F g-1 at a current density of 1 A g-1. After the 5000 cycles tests, the capacitance retained 83.54% at a current density of 2 A g-1. Meanwhile, the electrochemical impedance spectroscopy data shown the electrode materials had excellent capacity and good conductivity. Hence, the SNG aerogel prepared by l-cysteine-assisted solvothermal method is a great material for high-performance supercapacitors.

  18. Cea assessment of the sulphur-iodine cycle for hydrogen production

    International Nuclear Information System (INIS)

    Caries, Ph.; Vitart, X.; Yvon, P.

    2010-01-01

    The sulphur-iodine cycle is a promising process for hydrogen production using nuclear heat: - it is a purely thermochemical cycle, implying that hydrogen production will scale with volume rather than surface; - it only involves fluids, thus avoiding the often difficult handling of solids; - its heat requirements are well matched to the temperatures available from a Generation IV very/high temperature reactor. These characteristics seem very attractive for high efficiency and low cost massive hydrogen production. On the other hand, the efficiency of the cycle may suffer from the large over-stoichiometries of water and iodine and the very important heat exchanges it involves; furthermore, due to lack of adequate thermodynamic models, its efficiency is difficult to assess with confidence. Besides, the large quantities of chemicals that need to be handled, and the corrosiveness of these chemicals, are factors not to be overlooked in terms of investment and operation costs. In order to assess the actual potential of the sulphur-iodine cycle for massive hydrogen production at a competitive cost, CEA has been conducting an important programme on this cycle, ranging from thermodynamic measurements to hydrogen production cost evaluation, with flow sheet optimisation, component sizing and investment cost estimation as intermediate steps. The paper will present the method used, the status of both efficiency and production cost estimations, and discuss perspectives for improvement. (authors)

  19. Kinetics and mechanism of sphalerite leaching by sodium nitrate in sulphuric acid solution

    Directory of Open Access Journals (Sweden)

    Sokić M.

    2012-01-01

    Full Text Available Interest for application of hydrometallurgical processes in a processing of complex sulphide ores and concentrates has increased in recent years. Their application provides better metal recoveries and reduced emission of gaseous and toxic ageneses in the environment. The kinetics and mechanism of sphalerite leaching from complex sulphide concentrate with sulphuric acid and sodium nitrate solution at standard conditions was presented in this paper. The influences of temperature and time on the leaching degree of zinc were investigated and kinetic analysis of the process was accomplished. With temperature increasing from 60 to 90°C, the zinc leaching increased from 25.23% to 71.66% after 2 hours, i.e. from 59.40% to 99.83% after 4 hours. The selected kinetic model indicated that the diffusion through the product layer was the rate-controlling step during the sphalerite leaching. The activation energy was determined to be 55 kJ/mol in the temperature range 60-90°C. XRD, light microscopy and SEM/EDX analyses of the complex concentrate and leach residue confirmed formation of elemental sulphur and diffusion-controlled leaching mechanism.

  20. Relationship between sulphate and sulphur dioxide in the air

    Energy Technology Data Exchange (ETDEWEB)

    Fugas, M; Gentilizza, M

    1978-01-01

    The relationship between the sulphate in suspended particulates and sulphur dioxide in the air was studied in various urban and industrial areas. The relationship is best described by the equation y = ax/sup b/, where y is the percentage of the sulphate S in the total S (sulphate and sulphur dioxide) and x is the concentration of the total S in the air. The regression coefficients a and b seem to be characteristics of the area. In urban areas studied so far a was between 316 and 378 and b between -0.74 and -0.83. In industrial areas polluted by dust which contains elevated concentrations of metals a was between 91 and 107 and b between -0.35 and -0.49. In the area polluted by cement dust there was practically no correlation between the sulphate S (%) and the total S, but a relatively high correlation between absolute amounts of the sulphate S and the total S. The relations indicate that the limitation of SO/sub 2/ conversion is influenced by aerosol composition. Aerosols containing certain metals may promote the conversion by a catalytic effect while alkaline substances by increasing the pH. Whether this can only happen in the plume or in the air as well remains to be clarified.

  1. Rubber composites cured with sulphur and peroxide and ...

    Indian Academy of Sciences (India)

    Besides classical applications of rubber products in tyres, ... application of sulphur curing systems leads to the forming ..... mobile sulphidic cross-links which promote crystallization of NR. ... PhD Thesis (Kingston, Ontario: Queen's University).

  2. The implications of the new sulphur limits on the European Ro-Ro sector

    DEFF Research Database (Denmark)

    Zis, Thalis; Psaraftis, Harilaos N.

    2017-01-01

    In an effort to reduce the environmental impacts of maritime transportation, the International Maritime Organization (IMO) designated special Sulphur Emission Control Areas (SECAs) where ships are required to use low-sulphur fuel. In January 2015, the sulphur limit within SECAs was lowered to 0...... and the redistribution of transport. Recommendations to mitigate and reverse the negative side-effects of such environmental legislation are proposed....... analyses on market share data, cargo values, freight rates, and haulers rates are conducted. Emissions inventories are constructed to assess the environmental efficacy of the SECA regulation. The novelty of the proposed model lies in the examination of the ex-post implications of shutting down a service...

  3. Canopy interaction with precipitation and sulphur deposition in two boreal forests of Quebec, Canada

    International Nuclear Information System (INIS)

    Marty, C.; Houle, D.; Duchesne, L.; Gagnon, C.

    2012-01-01

    The interaction of atmospheric sulphur (S) was investigated within the canopies of two boreal forests in Québec, Canada. The net canopy exchange approach, i.e. the difference between S–SO 4 in throughfall and precipitation, suggests high proportion of dry deposition in winter (up to 53%) as compared to summer (1–9%). However, a 3.5‰ decrease in δ 18 O–SO 4 throughfall in summer compared to incident precipitation points towards a much larger proportion of dry deposition during the warm season. We suggest that a significant fraction of dry deposition (about 1.2 kg ha −1 yr −1 , representing 30–40% of annual wet S deposition) which contributed to the decreased δ 18 O–SO 4 in throughfall was taken up by the canopy. Overall, these results showed that, contrary to what is commonly considered, S interchanges in the canopy could be important in boreal forests with low absolute atmospheric S depositions. - Highlights: ► We investigated sulphur interactions with the canopy of two boreal forests, Québec. ► Sulphur interchanges within the canopy were large and vary with seasons. ► About 1.2 kg S–SO 4 ha −1 yr −1 was taken up by the canopy during warm seasons. ► This represents 30–40% of annual wet S–SO 4 deposition. ► Canopy uptake must be considered for sulphur budget estimations in boreal forests. - The equivalent of 30–40% of annual wet S–SO 4 deposition was taken up by the canopy of two boreal forests during warm seasons.

  4. Accidental sulphuric acid poisoning in a newborn | Abdulkadir ...

    African Journals Online (AJOL)

    Accidental sulphuric acid poisoning in a newborn. I Abdulkadir, L Hassan, F Abdullahi, FD Akeredolu, S Purdue, M Okpe, AM Sobowale, OA Adewumi, U Abdullahi, MA Onadiran, TT Sholadoye, S Baba, WN Ogala ...

  5. The non-participation of organic sulphur in acid mine drainage generation.

    Science.gov (United States)

    Casagrande, D J; Finkelman, R B; Caruccio, F T

    1989-12-01

    Acid mine drainage is commonly associated with land disturbances that encounter and expose iron sulphides to oxidising atmospheric conditions. The attendant acidic conditions solubilise a host of trace metals. Within this flow regime the potential exists to contaminate surface drinking water supplies with a variety of trace materials. Accordingly, in evaluating the applications for mines located in the headwaters of water sheds, the pre-mining prediction of the occurrence of acid mine drainage is of paramount importance.There is general agreement among investigators that coal organic sulphur is a nonparticipant in acid mine drainage generation; however, there is no scientific documentation to support this concensus. Using simulated weathering, kinetic, mass balance, petrographic analysis and a peroxide oxidation procedure, coal organic sulphur is shown to be a nonparticipant in acid mine drainage generation. Calculations for assessing the acid-generating potential of a sedimentary rock should not include organic sulphur content.

  6. High temperature corrosion behaviour of Ti-46.6Al-1.4Mn-2Mo in environments of low oxygen and high sulphur potentials at 750 and 900 C

    International Nuclear Information System (INIS)

    Du, H.L.; Datta, P.K.; Hwang, S.K.

    1997-01-01

    In this paper, the oxidation and sulphidation behaviour of a TiAl-based intermetallic, Ti-46.6Al-1.4Mn-2Mo (at%) with duplex and laminar microstructures, was investigated in environments of H 2 /H 2 S/H 2 O at 750 and 900 C. The corrosion kinetics of the intermetallic were determined by means of discontinuous gravimetry and the as-received and exposed samples were characterised using SEM, EDX and XRD. The weight gain/time data in the oxygen and sulphur containing environment used indicated parabolic kinetics with Kp∝10 -12 g 2 /cm 4 /s at 750 C and cubic kinetics at 900 C. The increase in exposure temperature did not significantly change the corrosion behaviour of the materials. The material showed the development of a multilayered scale consisting of an outermost TiO 2 layer beneath which an Al 2 O 3 layer existed: the formation of MnS and Al 2 S 3 was observed to occur between the oxide layers and substrate. This paper will discuss the significance of these results and consider the mechanisms responsible for degradation of this type of intermetallics in high sulphur and low oxygen environment with reference to their limit of temperature tolerance. (orig.)

  7. Trends in atmospheric deposition fluxes of sulphur and nitrogen in Czech forests

    International Nuclear Information System (INIS)

    Hůnová, Iva; Maznová, Jana; Kurfürst, Pavel

    2014-01-01

    We present the temporal trends and spatial changes of deposition of sulphur and nitrogen in Czech forests based on records from long-term monitoring. A statistically significant trend for sulphur was detected at most of the sites measuring for wet, dry, and total deposition fluxes and at many of these the trend was also present for the period after 2000. The spatial pattern of the changes in sulphur deposition flux between 1995 and 2011 shows the decrease over the entire forested area in a wide range of 18.1–0.2 g m −2 year −1 with the most pronounced improvement in formerly most impacted regions. Nitrogen still represents a considerable stress in many areas. The value of nitrogen deposition flux of 1 g m −2 year −1 is exceeded over a significant portion of the country. On an equivalent basis, the ion ratios of NO 3 − /SO 4 2− and NH 4 + /SO 4 2− in precipitation show significantly increasing trends in time similarly to those of pH. -- Highlights: • Significant decrease of sulphur deposition at most of sites has been recorded. • Nitrogen deposition still represents a considerable stress in Czech forests. • Significantly increasing trends of NO 3 − /SO 4 2− , NH 4 + /SO 4 2− , and pH in precipitation. -- While sulphur deposition significantly decreased with the highest improvement in formerly most affected areas, nitrogen deposition still represents a considerable stress in Czech forests

  8. Effects of phosphorus and sulphur on dry matter yield of maize ( Zea ...

    African Journals Online (AJOL)

    A screen-house experiment was conducted to investigate the effects of phosphorus (P) and sulphur (S) on maize dry-matter yield (MDY) in soils of five locations (Obantoko I, II, Alabata I, II, and III) in Abeokuta, Ogun State of Nigeria. Three levels of sulphur (0, 10 and 20 kg S ha–1) and phosphorus (0, 30 and 45 kg P ha–1) ...

  9. Fate of gypsum-sulphur applied to soybean on Typic haplustepts

    International Nuclear Information System (INIS)

    Saharan, Neelam; Rattan, R.K.

    2004-01-01

    Field experiments were conducted on the sulphur-deficient Typic Haplustepts of the IARI farm for two consecutive, kharif seasons viz. 1996 and 1997 with soybean cultivar Pusa 22 as the crop. Varying rates of S as gypsum were basally applied in the main plots adjacent to the micro plots (1 m x 1 m) to quantify the partitioning of the fertilizer-sulphur taken up by soybean and its distribution in the soil profile. Soybean responded to the application of sulphur, with increase in yield being obtained up to rate of 40 kg S ha -1 . Data computed on distribution of the S derived from labelled gypsum and percent S utilization by the soybean crop increased from 13.23 and 4.15 to 23.41 and 6.39, respectively. During 1996, the per cent utilization of labelled S ranged from 5.6 to 8.8. Monitoring of added sulphur in the soil profile up to a depth of 1 m revealed maximum accumulation of the added S in 30-60 cm soil layer. With the help of 35 S around 11 to 18 per cent of the added S was traced in 60-100 cm soil layer. It can be concluded from the data for two years that during kharif season the application of S through water soluble sources like ammonium sulphate and ammonium phosphate sulphate should be avoided because even S from the sparingly soluble gypsum migrated to a depth of 1 m during the cropping season. (author)

  10. NA35: sulphur-gold collision

    CERN Multimedia

    1991-01-01

    In this image the real particles produced by the collision of a 6400 GeV sulphur ion with a gold target can be seen as they pass through a streamer chamber. Streamer chambers consist of a gas chamber through which a strong pulsed electric field is passed, creating sparks as a charged particle passes through it. The NA35 experiment, which was in operation in the 1980s, was part of CERN's ongoing heavy ion project.

  11. Soil and applied sulphur utilization by sunflower grown on vertisol under rainfed conditions

    International Nuclear Information System (INIS)

    Sreemannarayana, B.; Sreenivasa Raju, A.

    1993-01-01

    In a field experiment, conducted with sunflower genotypes viz., Morden, APSH-11, and EC 68414 grown on a local black clay loam soil, fertilizer sulphur (labelled with 35 S) was applied at the rate of 0, 20, 40 and 60 kg S/ha through gypsum and ammonium sulphate. Among the sunflower genotypes, EC 68414 utilized maximum sulphur from the sources at any given growth stage i.e., star, bud, flowering and maturity. Sulphur applied through ammonium sulphate resulted in highest S utilization by all the genotypes at all the stages of growth. Though, sulphur uptake showed an increase, the S utilization decreased with increase in levels of S. The S uptake was highest at 60 kg S/ha level applied through any of the sources. The soil S uptake was higher than fertilizer S uptake at any given stage of crop. Maximum yields were recorded at 40 kg S/ha level signifying that this dose is optimum for sunflower grown on black clay loam soils. (author). 17 refs., 3 tabs

  12. Total mineral material, acidity, sulphur, and nitrogen in rain and snow at Kentville, Nova Scotia

    Energy Technology Data Exchange (ETDEWEB)

    Herman, F A; Gorham, E

    1957-01-01

    Analyses of total ash, sulphur, ph, ammonia, and nitrate nitrogen have been made on 23 monthly precipitation samples and 17 individual snow samples collected between June 1952 and May 1954 at Kentville, Nova Scotia, in a predominantly agricultural area. Mean annual supply of total mineral ash was 95 kg/ha, of sulphur 9.1 hg/ha, of ammonia nitrogen 2.8 kg/ha, and of nitrate nitrogen 1.1 kg/ha. Average pH was 5.7, and rains more acid than this exhibited higher levels of both nitrate and sulphur, and a marked correlation between the latter and ammonia. Snow samples had much lower concentrations of ash, sulphur, and nitrogen than rain samples collected in the same months, which may perhaps indicate a lower efficiency of snow flakes in removing materials from the atmosphere.

  13. Sulphur Nutrition and its Effect on Yield and Oil Content of Oilseed Rape (Brassica Napus L.

    Directory of Open Access Journals (Sweden)

    Mária Varényiová

    2017-01-01

    Full Text Available The aim of the experiment was to study the importance of sulphur in oilseed rape (Brassica napus L. nutrition as well as the effect of rising doses of sulphur in combination with nitrogen on yield, oiliness, oil production, nutrients content in seed and nutrients uptake by rapeseed. The plot–scale experiment was established in years 2013/14 and 2014/15 within the agricultural cooperative in Mojmírovce. There were four fertilization treatments on 600 m2 experimental plots in three replications in this experiment. The first treatment was unfertilized control. Other three treatments were fertilized by the same nitrogen dose of 160 kg.ha−1 and by increasing doses of sulphur. The second treatment was fertilized by a dose of 15 kg.ha−1 S, the third by a dose of 40 kg.ha−1 and a dose of 65 kg.ha−1 S was applied at the fourth treatment. The highest average yield 3.96 t.ha-1 was found when a dose of 40 kg.ha−1 S was applied. The application of sulphur in a dose of 65 kg.ha−1 was accompanied by a yield decrease by 11.4 % as compared to the treatment where a sulphur dose of 40 kg.ha−1 was used. An average oil content of 45.1, 45.5, and 44.0 % was found in treatments in which the doses of sulphur of 15, 40 and 65 kg.ha−1 were applied. No significant difference among the treatments fertilized by sulphur was found. The average oil production reached 1809, 1802 and 1595 kg.ha−1 in cases of treatments fertilized by sulphur doses of 15, 40 and 65 kg.ha−1.

  14. Analytical protocols for characterisation of sulphur-free lignin

    NARCIS (Netherlands)

    Gosselink, R.J.A.; Abächerli, A.; Semke, H.; Malherbe, R.; Käuper, P.; Nadif, A.; Dam, van J.E.G.

    2004-01-01

    Interlaboratory tests for chemical characterisation of sulphur-free lignins were performed by five laboratories to develop useful analytical protocols, which are lacking, and identify quality-related properties. Protocols have been established for reproducible determination of the chemical

  15. Analysis of sulphur, phosphorus and silica in metals, alloys, inorganic compounds and solvents

    International Nuclear Information System (INIS)

    Upadhya, J.C.; Naik, S.S.; Khedikar, W.K.; Sudersanan, M.; Mathur, P.K

    1999-10-01

    Procedures for the analysis of sulphur, phosphorus and silica in various metals and alloys like mild steel, carbon steel and stainless steel as well as nickel base alloys are described. Procedures were also developed for the analysis of sulphur in thoria pellets and in other materials like crack check fluids, coal etc. Typical results obtained are summarised. (author)

  16. Kinetics of bromide catalysed oxidation of dextrose by cerium (IV) in aqueous sulphuric acid solution

    International Nuclear Information System (INIS)

    Sharma, J.; Sah, M.P.

    1994-01-01

    Kinetics of bromide catalysed oxidation of dextrose by Ce IV in aqueous sulphuric acid medium show first order dependence each in dextrose and cerium(IV). The reaction rate decreases on increasing the concentration of hydrogen ion. The increase in [HSO 4 - ] or [SO 4 2- ] decreases the rate. The bromide ion shows positive catalytic effect on the reaction rate. The value of activation energy has been calculated and a suitable mechanism confirming to the kinetic data is proposed. (author). 3 refs., 3 tabs

  17. Past and future trends in concentrations of sulphur and nitrogen compounds in the Arctic

    DEFF Research Database (Denmark)

    Hole, Lars R.; Christensen, Jesper H.; Ruoho-Airola, Tuija

    2009-01-01

    Recent trends in nitrogen and sulphur compounds in air and precipitation from a range of Arctic monitoring stations are presented, with seasonal data from the late 70s to 2004 or 2005. Earlier findings of declining sulphur concentrations are confirmed for most stations, while the pattern is less ...

  18. Thermodynamic of the associated cycle and application to the assembly of thermochemical iodine sulphur cycle and a nuclear engine for the hydrogen production

    International Nuclear Information System (INIS)

    Dumont, Y.

    2008-01-01

    This thesis is devoted to the design of an assembly of a hydrogen production process by the thermochemical iodine-sulphur cycle and a nuclear reactor. The suggested coupling network uses a power cycle which produces a work which is directly used for the heat pump running. The purpose of this thermodynamic cycle association is to recover the rejected energy at low temperature of a process to provide the energy needs of this same process at high temperature. This association is applied to the studied coupling. The construction of the energy distribution network is designed by the pinch analysis. In the case of a conventional coupling, the efficiency of hydrogen production is 22.0%. By integrating the associated cycles into the coupling, the efficiency of production is 42.6%. The exergetic efficiency, representative of the energy using quality, increases from 58.7% to 85.4%. (author) [fr

  19. Catalysts macroporosity and their efficiency in sulphur sub-dew point Claus tail gas treating processes

    Energy Technology Data Exchange (ETDEWEB)

    Tsybulevski, A.M.; Pearson, M. [Alcoa Industrial Chemicals, 16010 Barker`s Point Lane, Houston, TX (United States); Morgun, L.V.; Filatova, O.E. [All-Russian Research Institute of Natural Gases and Gas Technologies VNIIGAZ, Moscow (Russian Federation); Sharp, M. [Porocel Corporation, Westheimer, Houston, TX (United States)

    1996-10-08

    The efficiency of 4 samples of alumina catalyst has been studied experimentally in the course of the Claus `tail gas` treating processes at the sulphur sub-dew point (TGTP). The samples were characterized by the same chemical and crystallographic composition, the same volume of micropores, the same surface area and the same catalytic activity but differed appreciably in the volume of macropores. An increase in the effective operation time of the catalysts before breakthrough of unrecoverable sulphur containing compounds, with the increasing macropore volume has been established. A theoretical model of the TGTP has been considered and it has been shown that the increase in the sulphur capacity of the catalysts with a larger volume of macropores is due to an increase in the catalysts efficiency factor and a slower decrease in their diffusive permeability during filling of micropores by sulphur

  20. Application of sodium carbonate prevents sulphur poisoning of catalysts in automated total mercury analysis

    Science.gov (United States)

    McLagan, David S.; Huang, Haiyong; Lei, Ying D.; Wania, Frank; Mitchell, Carl P. J.

    2017-07-01

    Analysis of high sulphur-containing samples for total mercury content using automated thermal decomposition, amalgamation, and atomic absorption spectroscopy instruments (USEPA Method 7473) leads to rapid and costly SO2 poisoning of catalysts. In an effort to overcome this issue, we tested whether the addition of powdered sodium carbonate (Na2CO3) to the catalyst and/or directly on top of sample material increases throughput of sulphur-impregnated (8-15 wt%) activated carbon samples per catalyst tube. Adding 5 g of Na2CO3 to the catalyst alone only marginally increases the functional lifetime of the catalyst (31 ± 4 g of activated carbon analyzed per catalyst tube) in relation to unaltered catalyst of the AMA254 total mercury analyzer (17 ± 4 g of activated carbon). Adding ≈ 0.2 g of Na2CO3 to samples substantially increases (81 ± 17 g of activated carbon) catalyst life over the unaltered catalyst. The greatest improvement is achieved by adding Na2CO3 to both catalyst and samples (200 ± 70 g of activated carbon), which significantly increases catalyst performance over all other treatments and enables an order of magnitude greater sample throughput than the unaltered samples and catalyst. It is likely that Na2CO3 efficiently sequesters SO2, even at high furnace temperatures to produce Na2SO4 and CO2, largely negating the poisonous impact of SO2 on the catalyst material. Increased corrosion of nickel sampling boats resulting from this methodological variation is easily resolved by substituting quartz boats. Overall, this variation enables an efficient and significantly more affordable means of employing automated atomic absorption spectrometry instruments for total mercury analysis of high-sulphur matrices.

  1. Experiences in sulphur capture in a 30 MWth Circulating Fluidized Bed boiler under oxy-combustion conditions

    International Nuclear Information System (INIS)

    Gómez, M.; Fernández, A.; Llavona, I.; Kuivalainen, R.

    2014-01-01

    CO 2 and SO 2 from fossil fuel combustion are contributors to greenhouse effect and acid rain respectively. Oxy-combustion technology produces a highly concentrated CO 2 stream almost ready for capture. Circulating Fluidized Bed (CFB) boiler technology allows in-situ injection of calcium-based sorbents for efficient SO 2 capture. CIUDEN's 30 MWth CFB boiler, supplied by Foster Wheeler and located at the Technology Development Centre for CO 2 Capture and Transport (es.CO 2 ) in Spain, is the first of its kind for executing test runs at large pilot scale under both air-combustion and oxy-combustion conditions. In this work, SO 2 emissions under different scenarios have been evaluated. Variables such as limestone composition, Ca/S molar ratio and bed temperature among others have been considered along different test runs in both air-combustion and oxy-combustion conditions to analyse its influence on SO 2 abatement. Fly and bottom ash, together with flue gas analysis have been carried-out. Desulphurization performance tests results are presented. - Highlights: •Sulphur capture efficiency (%) was higher in oxy-combustion compared to air-combustion in a 30 MW thermal CFB boiler using anthracite and limestone as sulphur sorbent. •For a Ca/S molar ratio higher than 2.6 there was barely any improvement on sulphur capture efficiency for both air-combustion and oxy-combustion conditions in a 30 MW thermal CFB boiler using anthracite and limestone as sulphur sorbent. •Optimum temperature for sulphur capture at a fixed Ca/S molar ratio is around 880–890 °C under oxy-combustion conditions and for anthracite coal with limestone as sorbent in a 30 MW thermal CFB boiler

  2. Low mass dimuon production in 200 GeV/c per nucleon sulphur ion collisions on heavy targets

    International Nuclear Information System (INIS)

    Vasseur, G.

    1989-11-01

    The HELIOS/2 experiment at CERN studies, among other features, low mass muon pairs production in 200 GeV/c per nucleon sulphur-nucleus interactions, compared to proton-nucleus interactions at the same energy. As muons interact weakly with nuclear matter, they provide relatively clean information on the initial state of these collisions. In addition, an anomalous production of low mass dileptons, with an unusual quadratic dependence upon multiplicity, could be a signature of quark-gluon plasma. To get the target produced dimuon signal, two sources of backgrounds have to be removed: the dimuon production in the dump and the pion and kaon decays into muons. After subtraction of these backgrounds, acceptance correction and normalization, a dimuon signal is obtained, especially at low mass. It is compatible with known sources of low mass dimuons: vector meson decays and Dalitz pairs. In proton-nucleus, this result is in contradiction with previous experiments. In sulphur-nucleus, no great effect giving evidence of quark-gluon plasma formation is observed [fr

  3. The remaining percentage of 32P after burning of sulphur tablet containing 32P

    International Nuclear Information System (INIS)

    Ke Weiqing

    1991-01-01

    Three types of sulphur tablet containing 32 P are made artificially. The remaining percentage of 32 P after burning of three types of sulphur tablets containing 32 P is 98.1 ± 1.3% for 1st and 2nd types and 97.2 ± 2.8% for 3rd type

  4. Hydrofluoric–nitric–sulphuric-acid surface treatment of tungsten for carbon fibre-reinforced composite hybrids in space applications

    Energy Technology Data Exchange (ETDEWEB)

    Kanerva, M., E-mail: Mikko.Kanerva@aalto.fi [Aalto University, School of Engineering, Department of Applied Mechanics, P.O.B. 14300, FI-00076 Aalto (Finland); Johansson, L.-S.; Campbell, J.M. [Aalto University, School of Chemical Technology, Department of Forest Products Technology, P.O.B. 16300, FI-00076 Aalto (Finland); Revitzer, H. [Aalto University, School of Chemical Technology, Department of Chemistry, P.O.B. 16300, FI-00076 Aalto (Finland); Sarlin, E. [Tampere University of Technology, Department of Materials Science, P.O.B. 589, FI-33101 Tampere (Finland); Brander, T.; Saarela, O. [Aalto University, School of Engineering, Department of Applied Mechanics, P.O.B. 14300, FI-00076 Aalto (Finland)

    2015-02-15

    Highlights: • XPS and AFM analysis of the effect of hydrofluoric–nitric–sulphuric-acid on tungsten. • Dreiling's model established 54.4% thinning of WO{sub 3} due to 67 s treatment. • Strain energy release rate increased ≈8.4 J/m{sup 2} at the interface. • Failure loci analysis expressed the oxide and carbon fibre surfaces as weak points. - Abstract: Hybrid material systems, such as combinations of tungsten foils and carbon fibre-reinforced plastic (CFRP), are replacing metal alloy concepts in spacecraft enclosures. However, a good adhesion between the tungsten oxide scale and the epoxy resin used is required. Here, the effects of a hydrofluoric–nitric–sulphuric-acid (HFNS) treatment on tungsten oxides and subsequent adhesion to CFRP are analysed using atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and fracture testing. The work shows that HFNS treatment results in decreased oxygen content, over 50% thinner tungsten trioxide (WO{sub 3}) layer and increased nano-roughness on thin tungsten foils. Fracture testing established a 39% increase in the average critical strain for tungsten–CFRP specimens after HFNS treatment was carried out on tungsten. The effect of the oxide scale modification regarding the critical strain energy release rate was ΔG{sub c}≈ 8.4 J/m{sup 2}.

  5. Effect of NPK fertilization and elemental sulphur on growth and yield of lowbush blueberry

    Directory of Open Access Journals (Sweden)

    M. STARAST

    2008-12-01

    Full Text Available The aim of the research was to determine the effect of fertilizers on the pH of former arable soils and on the growth and the yield of the lowbush blueberry (Vaccinium angustifolium Ait.. Lowbush blueberry fertilization experiments were established in 1999 at two locations – at Kärla, Saaremaa, West Estonia and at Vasula, Tartu County, South Estonia. Experimental sites were situated on different soils: soil pHKCl at Kärla was 5.5 and at Vasula 6.2. Elemental sulphur and acidifying fertilizers (ammonium sulfate, potassium sulfate and superphosphate were used in both plantations. Fertilizers were applied based on nutrient in the soil and sulphur was applied at 100 g m–2. Plant growth was recorded in 2001, 2002 and 2003. A positive influence of NPK fertilization on yield was found in both Kärla and Vasula, and yield were 336 g and 41 g higher compared to the control, respectively. The vegetative growth and yield of blueberry depended significantly on soil pH. Elemental sulphur increased soil acidity and on loamy sand soil did not increase plant productivity. The sulphur effect on soil pH began to decrease three years after application. Sulphur can be recommended to increase soil acidity in nutrient-rich soil but, not nutrient poor soil with light texture, where only NPK fertilizers were effective.;

  6. Trading sulphur emissions under the Second Sulphur Protocol

    Energy Technology Data Exchange (ETDEWEB)

    Foersund, Finn R.; Naevdal, Eric

    1997-07-01

    Emission trading is a potent policy instrument in theoretical analyses of environmental policy. However, trading in emission quotas of non-uniformly dispersed pollutants requires that the offsetting quantities vary with location of sources. Such a system is not yet in use. The Second Sulphur Protocol for Europe makes it possible to try out a system of ``exchange rates`` through a clause allowing ``joint implementation`` of emission reductions. In this report, the authors investigate some properties of a system with exogenous exchange rates within a simultaneous trade model based on cost efficiency. Incorporation of constraints on depositions in third party countries may be necessary in order to get third party country cooperation. It is demonstrated that imposition of constraints is feasible, but it is also revealed what demands such incorporation places on the design of the institutional setting. Constraints on trade should only be introduced when the concern for the environment of the various receptors fail to be captured adequately by the calibration of the exchange rates. 16 refs., 2 figs., 3 tabs.

  7. WATER PINCH TECHNOLOGY APPLICATION TO MINIMIZE SULPHUROUS WASTEWATER IN AN OIL REFINERY

    Directory of Open Access Journals (Sweden)

    Gabriel Orlando Lobelles Sardiñas

    2017-01-01

    Full Text Available In oil refining industries there is a high water consumption, which influences the high production costs and impacts the environment due to the discharge of their wastes. It is known that there are no technological conditions for the reuse of industrial water at the oil refineries, based on hydroskimming processes. The objective of this study is to implement the process integration methodology, Water Pinch, to a sour water stripper unit, as a unitary process of an oil refinery, to minimize the amount of sulphurous waste water and reduce contamination of the bay that receives these wastes. The technology is applied to evaluate the volume of sulphurous wastewater generated in the Cienfuegos oil refinery. This technology allows identifying opportunities for recovery and reuse of water, based on concentration ranges of contaminants. To achieve this purpose, a sour water stripper tower was assessed with the help of Water Pinch software, which provided an optimized distribution network, as a proposed technological improvement. This facilitated to recover and reuse 667 757, 28 m3 of water per year, and 1 035 023, 78 CUC were saved, at the same time the amount of polluting effluents decreased in approximately 2 % of non-reusable treated water.

  8. Jet A and low sulphur diesel production and blending experience in a synthetic crude-rich environment

    International Nuclear Information System (INIS)

    1997-01-01

    The Sunoco Sarnia Refinery has produced large volumes of high quality Jet A and Low Sulphur Diesel without major capital investment. They have done this by blending the synergy between hydrocracked and synthetic-based distillate stocks. The Sunoco Sarnia Refinery has two crude units, a Catalytic Cracker, a Hydrocracker and a Hydrogen unit, two reformers, Alkylation and BTX units. It also has the usual facilities such as gas plants, gasoline treater, and a naphtha pre-treater for former feed and an amine sulphur unit. Refinery distillate products, crudes used, components used for blending the distillate products, cost of the facilities and average production of each product were reviewed. A schematic of the Sarnia Refinery Distillate Production Facility was provided. 1 tab., 1 fig

  9. Density of states of adsorbed sulphur atoms on pristine and defective graphene layers

    International Nuclear Information System (INIS)

    Arellano, J S

    2017-01-01

    The density of states for adsorbed sulphur atom on a graphene layer system is discussed for pristine graphene layer and for mono and divacancies on the graphene layer. To our knowledge this is the first time that an entire adsorption of the sulphur atom is reported at the plane of the carbon atoms, when there is a pair of closer vacancies at the graphene layer. (paper)

  10. Sulphur chemistry in the L1544 pre-stellar core

    Science.gov (United States)

    Vastel, Charlotte; Quénard, D.; Le Gal, R.; Wakelam, V.; Andrianasolo, A.; Caselli, P.; Vidal, T.; Ceccarelli, C.; Lefloch, B.; Bachiller, R.

    2018-05-01

    The L1544 pre-stellar core has been observed as part of the ASAI IRAM 30m Large Program as well as follow-up programs. These observations have revealed the chemical richness of the earliest phases of low-mass star-forming regions. In this paper we focus on the twenty-one sulphur bearing species (ions, isotopomers and deuteration) that have been detected in this spectral-survey through fifty one transitions: CS, CCS, C3S, SO, SO2, H2CS, OCS, HSCN, NS, HCS+, NS+ and H2S. We also report the tentative detection (4 σ level) for methyl mercaptan (CH3SH). LTE and non-LTE radiative transfer modelling have been performed and we used the NAUTILUS chemical code updated with the most recent chemical network for sulphur to explain our observations. From the chemical modelling we expect a strong radial variation for the abundances of these species, which mostly are emitted in the external layer where non thermal desorption of other species has previously been observed. We show that the chemical study cannot be compared to what has been done for the TMC-1 dark cloud, where the abundance is supposed constant along the line of sight, and conclude that a strong sulphur depletion is necessary to fully reproduce our observations of the prototypical pre-stellar core L1544.

  11. First approach to studies of sulphur electron DOS in prostate cancer cell lines and tissues studied by XANES

    International Nuclear Information System (INIS)

    Kwiatek, Wojciech M.; Czapla, Joanna; Podgorczyk, Magdalena; Kisiel, Andrzej; Konior, Jerzy; Balerna, Antonella

    2011-01-01

    Urological cancers comprise approximately one-third of all cancers diagnosed in men worldwide and out of these, prostate cancer is the most common one (). Several risk factors such as age, hormone levels, environmental conditions and family history are suspected to play a role in the onset of this disease of otherwise obscure aetiology. It is therefore the medical need that drives multidisciplinary research in this field, carried out by means of various experimental and theoretical techniques. Out of many relevant factors, it is believed that sulphur can take an important part in cancer transformations. We have investigated the prostate cancer cell lines and tissues, along with selected organic and inorganic compounds used as references, by the X-ray absorption fine structure spectroscopy near the sulphur edge energy region. Particularly, the comparison of the experimental results collected during XANES measurements and theoretical calculations of electron density of states with use of the FEFF8 code and LAPW (linearised augmented plane-wave) method has been performed and in this work the first results of our studies are presented. - Highlights: → Different forms of sulphur has been found in prostate cancer cells. → FEFF8 code and LAPW method gave fairly good correspondence with the experiment. → LAPW is able to reproduce the fine structure of the absorption spectra. → Calculated DOS showed the influence of core atom on the shape of XANES spectra.

  12. Dry deposition of sulphur on the Mpumalanga highveld: a pilot study using the inferential method

    CSIR Research Space (South Africa)

    Zunckel, M

    1996-10-01

    Full Text Available contributions come from SO2 at night and from particulates during the day in both seasons. The contribution to the total dry deposition sulphur load by particulates at night appears to be negligible. Assuming that sulphur precipitation for the two monitoring...

  13. DNA damage in internal organs after cutaneous exposure to sulphur mustard

    Energy Technology Data Exchange (ETDEWEB)

    Batal, Mohamed [Laboratoire « Lésions des Acides Nucléiques », Université Joseph Fourier – Grenoble 1/CEA/Institut Nanoscience et Cryogénie/SCIB, UMR-E3, Grenoble (France); Département de Toxicologie et Risques Chimiques, Unité de Brûlure Chimique, Institut de Recherche Biomédicale des Armées, Antenne de La Tronche, BP87, F-38702 La Tronche Cedex (France); Boudry, Isabelle; Mouret, Stéphane; Cléry-Barraud, Cécile; Wartelle, Julien [Département de Toxicologie et Risques Chimiques, Unité de Brûlure Chimique, Institut de Recherche Biomédicale des Armées, Antenne de La Tronche, BP87, F-38702 La Tronche Cedex (France); Bérard, Izabel [Laboratoire « Lésions des Acides Nucléiques », Université Joseph Fourier – Grenoble 1/CEA/Institut Nanoscience et Cryogénie/SCIB, UMR-E3, Grenoble (France); Douki, Thierry, E-mail: thierry.douki@cea.fr [Laboratoire « Lésions des Acides Nucléiques », Université Joseph Fourier – Grenoble 1/CEA/Institut Nanoscience et Cryogénie/SCIB, UMR-E3, Grenoble (France)

    2014-07-01

    Sulphur mustard (SM) is a chemical warfare agent that attacks mainly skin, eye and lungs. Due to its lipophilic properties, SM is also able to diffuse through the skin and reach internal organs. DNA represents one of the most critical molecular targets of this powerful alkylating agent which modifies DNA structure by forming monoadducts and biadducts. These DNA lesions are involved in the acute toxicity of SM as well as its long-term carcinogenicity. In the present work we studied the formation and persistence of guanine and adenine monoadducts and guanine biadducts in the DNA of brain, lungs, kidneys, spleen, and liver of SKH-1 mice cutaneously exposed to 2, 6 and 60 mg/kg of SM. SM-DNA adducts were detected in all studied organs, except in liver at the two lowest doses. Brain and lungs were the organs with the highest level of SM-DNA adducts, followed by kidney, spleen and liver. Monitoring the level of adducts for three weeks after cutaneous exposure showed that the lifetime of adducts were not the same in all organs, lungs being the organ with the longest persistence. Diffusion from skin to internal organs was much more efficient at the highest compared to the lowest dose investigated as the result of the loss of the skin barrier function. These data provide novel information on the distribution of SM in tissues following cutaneous exposures and indicate that brain is an important target. - Highlights: • Sulphur mustard reaches internal organs after skin exposure • Adducts are detected in the DNA of internal organs • Brain is the organ with the highest level of DNA damage • The barrier function of skin is lost at high dose of sulphur mustard • DNA adducts persist in organs for 2 or 3 weeks.

  14. DNA damage in internal organs after cutaneous exposure to sulphur mustard

    International Nuclear Information System (INIS)

    Batal, Mohamed; Boudry, Isabelle; Mouret, Stéphane; Cléry-Barraud, Cécile; Wartelle, Julien; Bérard, Izabel; Douki, Thierry

    2014-01-01

    Sulphur mustard (SM) is a chemical warfare agent that attacks mainly skin, eye and lungs. Due to its lipophilic properties, SM is also able to diffuse through the skin and reach internal organs. DNA represents one of the most critical molecular targets of this powerful alkylating agent which modifies DNA structure by forming monoadducts and biadducts. These DNA lesions are involved in the acute toxicity of SM as well as its long-term carcinogenicity. In the present work we studied the formation and persistence of guanine and adenine monoadducts and guanine biadducts in the DNA of brain, lungs, kidneys, spleen, and liver of SKH-1 mice cutaneously exposed to 2, 6 and 60 mg/kg of SM. SM-DNA adducts were detected in all studied organs, except in liver at the two lowest doses. Brain and lungs were the organs with the highest level of SM-DNA adducts, followed by kidney, spleen and liver. Monitoring the level of adducts for three weeks after cutaneous exposure showed that the lifetime of adducts were not the same in all organs, lungs being the organ with the longest persistence. Diffusion from skin to internal organs was much more efficient at the highest compared to the lowest dose investigated as the result of the loss of the skin barrier function. These data provide novel information on the distribution of SM in tissues following cutaneous exposures and indicate that brain is an important target. - Highlights: • Sulphur mustard reaches internal organs after skin exposure • Adducts are detected in the DNA of internal organs • Brain is the organ with the highest level of DNA damage • The barrier function of skin is lost at high dose of sulphur mustard • DNA adducts persist in organs for 2 or 3 weeks

  15. Effects of sulphur addition on modification and mechanical ...

    African Journals Online (AJOL)

    CW Onyia, BA Okorie, NI Amalu, SI Neife ... The results showed that the addition of sulphur to Al-12wt%Si alloy modified the Al-Si eutectic ... of the eutectic silicon structure with significant decrease in mechanical properties of the alloy and this ...

  16. Population ecology of the tonguefish Symphurus thermophilus (Pisces; Pleuronectiformes; Cynoglossidae) at sulphur-rich hydrothermal vents on volcanoes of the northern Mariana Arc

    Science.gov (United States)

    Tunnicliffe, Verena; Tyler, Jennifer; Dower, John F.

    2013-08-01

    Flatfish are a major component of the hydrothermal vent community on three seamounts of the northern Mariana Volcanic Arc in the northwest Pacific. Nikko, Kasuga-2 and Daikoku seamounts host vent fields between 375 and 480 m depth where high temperature vents release molten sulphur. The small cynoglossid tonguefish, Symphurus thermophilus Munroe and Hashimoto, is ubiquitous in all vent habitats observed on these seamounts: among extensive fields of tubeworms and mussels and on solid sulphur surfaces on Nikko; on sulphur-rich sediments and barnacle-covered boulders on Kasuga-2; and on recent sulphur flows and on broad areas of loose and semi-consolidated sediments on Daikoku. We recorded repeated forays by individuals onto flows of molten sulphur as these surfaces cooled. Based on observations using ROVs, the mean density is 90 fish/m2 with maximum counts over 200 fish/m2 on Daikoku sediments. Compared to collected tonguefish from Daikoku and Kasuga-2, those from Nikko have significantly greater lengths and, on average, six times the mass. Otolith data indicate upper ages of 13 years with Nikko tonguefish growing significantly faster. Diets of tonguefish on the three seamounts reflect the different habitats and prey availability; in Daikoku specimens, small crustaceans and polychaetes are most common while on Nikko, gut contents are predominantly larger shrimp. We made the unusual observation of stunned midwater fish falling to the seafloor near the vents where S. thermophilus immediately attacked them. This tonguefish has a wide diet range and foraging behaviour that likely influence the differing growth rates and sizes of fish inhabiting the different vent sites. Limited genetic data suggest that larval exchange probably occurs among sites where the common habitat factor is high levels of elemental sulphur forming hard and partly unconsolidated substrata. Here, in the northern range of the Mariana Trench Marine National Monument, S. thermophilus, despite having an

  17. Separation of uranium, molibdenum and vanadium in sulphuric solutions by extraction with alamine 336

    International Nuclear Information System (INIS)

    Floh, B.

    1976-01-01

    Alamine 336 - varsol - sulphuric acid-water system used for uranium, molibdenum and vanadium extraction, from sulphuric leaching and an appropriate plan for fractioning those elements are investigated. The behavior of cited elements in pure solutions followed by interaction that occurs in both bynary and tertiary systems are studied. Distribution coefficient is regarded for measuring such effects [pt

  18. Sulphur bacteria mediated formation of Palaeoproterozoic phosphorites

    Science.gov (United States)

    Joosu, Lauri; Lepland, Aivo; Kirsimäe, Kalle

    2014-05-01

    Modern phosphorite formation is typically associated with high productivity in upwelling areas where apatite (Ca-phosphate) precipitation is mediated by sulphur oxidising bacteria [1]. They inhabit the oxic/anoxic interface within the upper few centimetres of sediment column, accumulating phosphate in their cells under oxic conditions and releasing it rapidly when conditions become anoxic. Sulphur bacteria are known to live in close association with a consortium of anaerobic methane oxidising archaea and syntrophic sulphate-reducing bacteria. Paleoproterozoic, c. 2.0 Ga Zaonega Formation in Karelia, Russia contains several P-rich intervals in the upper part of 1500 m thick succession of organic-rich sedimentary rocks interlayered with mafic tuffs and lavas. Apatite in these P-rich intervals forms impure laminae, lenses and round-oval nodules which diameters typically range from 300 to 1000 μm. Individual apatite particles in P-rich laminae and nodules commonly occur as cylinders that are 1-8 μm long and have diameters of 0.5-4 μm. Cross-sections of best preserved cylindrical apatite particles reveal a thin outer rim whereas the internal parts consist of small anhedral elongated crystallites, intergrown with carbonaceous material. During recrystallization the outer rim thickens towards interior and cylinders may attain hexagonal crystal habit, but their size and shape remains largely unchanged [2]. The sizes of Zaonega nodules are similar to giant sulphide-oxidising bacteria known from modern and ancient settings [3, 4]. Individual apatite cylinders and aggregates have shapes and sizes similar to the methanotrophic archaea that inhabit microbial mats in modern seep/vent areas where they operate in close associations with sulphur-oxidising microbial communities [5]. Seep/vent influence during the Zaonega phosphogenesis is indicated by variable, though positive Eu anomaly, expected in magmatically active sedimentary environment experiencing several lava flows

  19. Specification of a technically justified limiting value for sulphur concentrations in heating oil in order to enhance the use of high-efficiency boiler technology in oil heating systems; Ermittlung eines technisch begruendeten Grenzwertes fuer Schwefelgehalte im Heizoel zur Foerderung des Einsatzes von Brennwerttechnologie in Oelheizungsanlagen

    Energy Technology Data Exchange (ETDEWEB)

    Bellingen, E.-M.; Kuechen, C. [Institut fuer Wirtschaftliche Oelheizung e.V., Hamburg (Germany); Haase, F.; Wilckens, H. [Deutsche Shell AG, Hamburg (Germany); Sinnen, H.D. [VEBA AG, Duesseldorf (Germany)

    2002-04-01

    Different oil condensing boilers, which were available on the German market, have been investigated in order to determine the relevant limit for sulphur content in domestic heating oil. Up to now, the condensate from oil condensing boilers has to be neutralized in many cases due to local legislation. The composition of the condensates from oil boilers came out to be similar to the condensate from gas condensing boilers, as long as the sulphur content of heating oil is below 100 mg/kg. As the neutralization of condensate from gas condensing boilers is usually not required up to 200 kW-boilers, there should be no technical reason for neutralization, as long as the sulphur content is below 100 mg/kg. However, boiler manufactures are convinced, that only if the sulphur content is as low as 50 mg/kg, it will be possible to develop reliable oil condensing boilers for a reasonable price. Calculations of the total energy consumption came to the result, that primary energy can be saved. The increase of efficiency on the boiler side has more influence than the energy needed for desulphurization. (orig.) [German] Zur Bestimmung eines technisch begruendeten Schwefelgrenzwertes fuer ein neues 'schwefelarmes' Heizoel EL wurden Untersuchungen mit Heizoelen unterschiedlichen Schwefelgehaltes an verschiedenen auf dem Markt verfuegbaren Oelbrennwertgeraeten durchgefuehrt. Zur Zeit wird durch das ATV Arbeitsblatt A-251 eine Neutralisation von Kondensaten aus Oelbrennwertanlagen gefordert. Die Untersuchungen zeigen, dass bei Schwefelgehalten unter 100 mg/kg die Kondensate aehnliche Zusammensetzungen aufweisen wie Kondensate aus Gasbrennwertgeraeten. Die Voraussetzung fuer eine Befreiung von der Neutralisationsverpflichtung bei der Verwendung dieser Brennstoffe ist damit aus technischer Sicht gegeben. Fuer die Entwicklung von neuen, kompakten und preiswerten Oelbrennwertgeraeten wird von der Heizgeraeteindustrie ein Schwefelgehalt von max. 50 mg/kg fuer notwendig gehalten

  20. Modelled transport and deposition of sulphur over Southern Africa

    CSIR Research Space (South Africa)

    Zunckel, M

    2000-01-01

    Full Text Available Ambient SO2 concentrations and atmospheric deposition of sulphur resulting from emissions on the industrialised highveld region of South Africa are estimated using the multi-scale atmospheric transport and chemistry (MATCH) modelling system...

  1. Electron capture detection of sulphur gases in carbon dioxide at the parts-per-billion level

    International Nuclear Information System (INIS)

    Pick, M.E.

    1979-01-01

    A gas chromatograph with an electron capture detector has been used to determine sulphur gases in CO 2 at the parts-per-billion level, with particular application to the analysis of coolant from CO 2 cooled nuclear reactors. For COS, CS 2 , CH 3 SH, H 2 S and (CH 3 ) 2 S 2 the detector has a sensitivity comparable with the more commonly used flame photometric detector, but it is much less sensitive towards (CH 3 ) 2 S and thiophene. In addition, the paper describes a simple method for trapping sulphur gases which might enable detection of sub parts-per-billion levels of sulphur compounds. (Auth.)

  2. Marinobacterium sp. strain DMS-S1 uses dimethyl sulphide as a sulphur source after light-dependent transformation by excreted flavins.

    Science.gov (United States)

    Hirano, Hiroyuki; Yoshida, Takako; Fuse, Hiroyuki; Endo, Takayuki; Habe, Hiroshi; Nojiri, Hideaki; Omori, Toshio

    2003-06-01

    Marinobacterium sp. strain DMS-S1 is a unique marine bacterium that can use dimethyl sulphide (DMS) as a sulphur source only in the presence of light. High-performance liquid chromatography (HPLC) analyses of the culture supernatant revealed that excreted factors, which could transform DMS to dimethyl sulphoxide (DMSO) under light, are FAD and riboflavin. In addition, FAD appeared to catalyse the photolysis of DMS to not only DMSO but also methanesulphonate (MSA), formate, formaldehyde and sulphate. As strain DMS-S1 can use sulphate and MSA as a sole sulphur source independently of light, the excretion of flavins appeared to support the growth on DMS under light. Furthermore, three out of 12 marine bacteria from IAM culture collection were found to be able to grow on DMS with the aid of photolysis by the flavins excreted. This is the first report that bacteria can use light to assimilate oceanic organic sulphur compounds outside the cells by excreting flavins as photosensitizers.

  3. Volatile sulphur compounds in morning breath of human volunteers.

    NARCIS (Netherlands)

    Snel, J.; Burgering, M.; Smit, B.; Noordman, W.; Tangerman, A.; Winkel, E.G.; Kleerebezem, M.

    2011-01-01

    OBJECTIVE: morning breath contains elevated concentrations of volatile sulphur components (VSCs). Therefore, morning breath is recognised as a surrogate target for interventions on breath quality. Nevertheless, factors influencing morning breath are poorly understood. Our aim was to evaluate

  4. Volatile sulphur compounds in morning breath of human volunteers

    NARCIS (Netherlands)

    Snel, Johannes; Burgering, Maurits; Smit, Bart; Noordman, Wouter; Tangerman, Albert; Winkel, Edwin G.; Kleerebezem, Michiel

    Objective: Morning breath contains elevated concentrations of volatile sulphur components (VSCs). Therefore, morning breath is recognised as a surrogate target for interventions on breath quality. Nevertheless, factors influencing morning breath are poorly understood. Our aim was to evaluate

  5. Sulphur mountain: Cosmic ray intensity records

    International Nuclear Information System (INIS)

    Venkatesan, D.; Mathews, T.

    1985-01-01

    This book deals with the comic ray intensity registrations at the Sulphur Mountain Cosmic Ray Laboratory. The time series of intensity form a valuable data-set, for studying cosmic ray intensity variations and their dependence on solar activity. The IGY neutron monitor started operating from July 1, 1957 and continued through 1963. Daily mean values are tabulated for the period and these are also represented in plots. This monitor was set up by the National Research Council of Canada

  6. Optimisation of Dilute Sulphuric Acid Hydrolysis of Waste ...

    African Journals Online (AJOL)

    Dilute sulphuric acid hydrolysis of waste paper was investigated in this study. The effects of acid concentration, time, temperature and liquid to solid ratio on the total reducing sugar concentration were studied over three levels using a four variable Box-Behnken design (BBD). A statistical model was developed for the ...

  7. On the effects of organic matter and sulphur-containing compounds on the CCN activation of combustion particles

    Directory of Open Access Journals (Sweden)

    A. Petzold

    2005-01-01

    Full Text Available The European PartEmis project (Measurement and prediction of emissions of aerosols and gaseous precursors from gas turbine engines was focussed on the characterisation and quantification of exhaust emissions from a gas turbine engine. The combustion aerosol characterisation included on-line measurements of mass and number concentration, size distribution, mixing state, thermal stability of internally mixed particles, hygroscopicity, cloud condensation nuclei (CCN activation potential, and off-line analysis of chemical composition. Based on this extensive data set, the role of sulphuric acid coating and of the organic fraction of the combustion particles for the CCN activation was investigated. Modelling of CCN activation was conducted using microphysical and chemical properties obtained from the measurements as input data. Coating the combustion particles with water-soluble sulphuric acid, increases the potential CCN activation, or lowers the activation diameter, respectively. The adaptation of a Köhler model to the experimental data yielded coatings from 0.1 to 3 vol-% of water-soluble matter, which corresponds to an increase in the fraction of CCN-activated combustion particles from ≤10−4 to ≌10−2 at a water vapour saturation ratio Sw=1.006. Additional particle coating by coagulation of combustion particles and aqueous sulphuric acid particles formed by nucleation further reduces the CCN activation diameter. In contrast, particles containing a large fraction of non-volatile organic compounds grow significantly less at high relative humidity than particles with a lower content of non-volatile OC. The resulting reduction in the potential CCN activation with an increasing fraction of non-volatile OC becomes visible as a trend in the experimental data. While a coating of water-soluble sulphuric acid increases the potential CCN activation, or lowers the activation diameter, respectively, the non-volatile organic compounds, mainly found at

  8. Influence of sulphur and multi-component fertilizer application on the content of Cu, Zn and Mn in different types of soil under maize

    Directory of Open Access Journals (Sweden)

    Barbara MURAWSKA

    2017-09-01

    Full Text Available The aim of the study was to determine the influence of the soil type and differential sulphur rates used with or without Basfoliar 36 Extra on the soil pH as well as the amount of available forms of copper, zinc and manganese based on the micro plots field experiment. Moreover, the relationship between the studied microelements was examined. The experiment was performed in two-factor design; the first-order factor was the soil type (Typic Hapludolls, Typic Hapludalfs, Typic Haplorthods, Typic Endoaquolls, while the second-order factor - fertilization with sulphur and compound fertilizer - Basfoliar 36 Extra. The plant tested was Rota cultivar maize. The use of sulphur and sulphur combined with Basfoliar 36 Extra changed the classification of the soils in terms of their pH. In the soils under study, as a result of the 10-years application of sulphur and/or foliar fertiliser with NPK fertilization as well as growing maize in monoculture showing a high uptake of macro- and micro-nutrients, there was reported a clear decrease in the content of zinc, copper and manganese, as compared with the initial content. With that in mind, one shall assume that growing maize in a 10-year monoculture is connected with an intensive use of soils, which can result in a clear deficit of the elements studied in soil.

  9. Effect of soil moisture on sulphur accumulation in overground plant organs and their harm in emmission conditions

    Energy Technology Data Exchange (ETDEWEB)

    Navara, J; Horvath, I; Hauskrecht, I

    1972-01-01

    The effect of different soil moisture on sulphur accumulation in the overground organs of Fagopyrum esculentum, moench in immission conditions is dealt with in this paper. The results obtained have shown that even under equal soil conditions, equal nutrient supply and age evenness of the analyzed material the total sulphur content of leaves grown in immission conditions (sulphur oxides, hydrogen sulphide, carbon disulphide, etc.) at equal soil moisture was essentially higher when compared with unirrigated plants and corresponded also to the degree of harm and crop reduction of the experimental plants. Therefore it is necessary when utilizing sulphur content of indicating plants, which serves for a large-area diagnosis of vegetation harm with immissions, to take into consideration, in addition to other factors (soil, nutrition, age of plants), the soil moisture as well.

  10. Physico-chemical conversion of sulphur dioxide in a power plant plume

    International Nuclear Information System (INIS)

    Lewin, E.E.

    1978-03-01

    A review is given of the actual knowledge of SO 2 atmospheric processes gained from laboratory and field experiments. Implementation is described of the instrumentation, operational procedures and analytical methods in connection with a field study of the conversion and dispersion of SO 2 in an oil-fired power plant plume. Furthermore, the preliminary results are included of five experiments performed until the end of 1976. Measurements were performed from an aircraft and included continuous registration of NOsub(x), SO 2 , SF 6 , and particle concentrations, as well as temperature and humidity. It was planned to label sulphur from the source in question with sulphur-35. However, this part of the experiment had to be abandoned because of public opinion on the use of radioactive tracers. Sulphur hexafluoride was used as an internal tracer for the plume. A half-life for SO 2 of about 30 min was determined from one of the experiments. In this connection the possibility of using NOsub(x) as a conservative tracer is shown. Possible ways of removal are discussed and the rate of two of the processes is calculated by means of a model describing the chemical conversion in a dispersing plume. (author)

  11. Energy balance calculations and assessment of two thermochemical sulfur cycles

    International Nuclear Information System (INIS)

    Leger, D.; Lessart, P.; Manaud, J.P.; Benizri, R.; Courvoisier, P.

    1978-01-01

    Thermochemical cyclic processes which include the highly endothermal decomposition of sulphuric acid are promising for hydrogen production by water-splitting. Our study is directed toward two cycles of this family, each involving the formation and decomposition of sulphuric acid and including other reactions using iron sulphide for the first and oxides and bromides of copper and magnesium for the second. Thermochemical analyses of the two cycles are undertaken. Thermodynamic studies of the reactions are carried out, taking into account possible side-reactions. The concentration of reactants, products and by-products resulting from simultaneous equilibria are calculated, the problems of separation thoroughly studied and the flow-diagrams of the processes drawn up. Using as heat source the helium leaving a 3000 MWth high temperature nuclear reactor and organizing internal heat exchange the enthalpy diagrams are drawn up and the net energy balances evaluated. The overall thermal efficiencies are about 28%, a value corresponding to non-optimized process schemes. Possible improvements aiming at energy-saving and increased efficiency are indicated

  12. Incisional Colopexy for Treatment of Chronic, Recurrent Colocloacal Prolapse in a Sulphur-Crested Cockatoo (Cacatua galerita)

    NARCIS (Netherlands)

    van Zeeland, Yvonne; Schoemaker, Nico; van Sluijs, Freek

    2014-01-01

    Objective To report a surgical technique for treatment of chronic, recurrent cloacal prolapse in a sulphur-crested cockatoo (Cacatua galerita). Study Design Clinical report Animals Sulphur-crested cockatoo (n = 1) Methods The bird was admitted with a 2-year history of periodic lethargy, decreased

  13. Leaching of a Cu-Co ore from Congo using sulphuric acidhydrogen peroxide leachants

    Directory of Open Access Journals (Sweden)

    Seo S.Y.

    2013-01-01

    Full Text Available A Cu-Co ore from Katinga Province, the Republic of Congo containing 1.5% Co and 1.6% Cu was tested to determine the leachability of Cu and Co using sulphuric acid and hydrogen peroxide mixtures at different conditions. Without hydrogen peroxide, the maximum extraction of copper and cobalt were found to be ~80% and ~15%, respectively when the acid concentration was varied between 0.36 - 1.1M. When hydrogen peroxide was added (0.008-0.042M, Cu recovery was enhanced to ~90%. Recoveries of ~90% of Co could be achieved at 20ºC, using leachants consisting of 0.36M sulphuric acid and 0.025M hydrogen peroxide after 3 hours. The reaction time to reach 90% Co extraction was reduced to less than 2 hours at 30ºC. Stabcal modelling of the Eh-pH diagrams shows the importance of hydrogen peroxide as a reductant. The decrease of solution potential (300-350 mV by adding hydrogen peroxide was confirmed by Eh measurements during the tests. The leaching follows the shrinking core model kinetics, where the rate constant is linearly dependent on hydrogen peroxide concentration in the range 0-0.025M and proportional to (1/r2 where r is the average radius of the mineral particles. The activation energy for the leaching process is 72.3 kJ/mol.

  14. Effects of cold stratification, sulphuric acid, submersion in hot and ...

    African Journals Online (AJOL)

    Effects of cold stratification, sulphuric acid, submersion in hot and tap water pretreatments in the greenhouse and open field conditions on germination of bladder-Senna ( Colutea armena Boiss. and Huet.) seeds.

  15. Efficiency of Syrian and Indian rock phosphates for maize in two soils amended with sulphur

    International Nuclear Information System (INIS)

    Kanacri, S.

    1995-01-01

    A greenhouse pot experiment was conducted to evaluate the fertilizer use efficiency of three Syrian rock phosphates in comparison to Mussoorie rock phosphate from India for maize grown in a laterite (ultisol) and an alluvial (entisol) soil amended with sulphur, and using sup 3 sup 2 P-labelled triple superphosphate (TSP). Results showed that application of rock phosphates (RPs) to laterite soil significantly increased the dry matter yields of maize shoots, whereas, in alluvial soil, RPs were not found effective in increasing the yields. Data further indicated that all the three Syrian RPs were equally efficient in increasing dry matter yields in laterite soil and were superior to Mussoorie rock phosphate (MRP). Sulphur added in combination with RPs significantly enhanced the dry matter production as well as 'A' value of alluvial soil. Application of sulphur in conjunction with RPs significantly increased the 'A' value of laterite soil however, sulphur did not contribute to any significant increase in the yields. Syrian RPs were more reactive in soils than Mussoorie RP. (author). 7 refs., 6 tabs

  16. Efficiency of Syrian and Indian rock phosphates for maize in two soils amended with sulphur

    International Nuclear Information System (INIS)

    Kanacri, Saloi; Bhujbal, B.M.

    1993-01-01

    A greenhouse pot experiment was conducted to evaluate the fertilizer use efficiency of three Syrian rock phosphates in comparison to Mussoorie rock phosphate from India for maize grown in a laterite (ultisol) and an alluvial (entisol) soil amended with sulphur, and using 32 P-labelled triple superphosphate (TSP). Results showed that application of rock phosphates (RPs) to laterite soil significantly increased the dry matter yields of maize shoots, whereas, in alluvial soil, RPs were not found effective in increasing the yields. Data further indicated that all the three Syrian RPs were equally efficient in increasing dry matter yields in laterite soil and were superior to Mussoorie rock phosphate (MRP). Sulphur added in combination with RPs significantly enhanced the dry matter production as well as 'A'value of alluvial soil. Application of sulphur in conjunction with RPs significantly increased the 'A' value of laterite soil, however, sulphur did not contribute to any significant increase in the yields. Syrian RPs were more reactive in soils than Mussoorie RP. (author). 7 refs., 6 tabs

  17. Hot atom chemistry of sulphur

    International Nuclear Information System (INIS)

    Todorovski, D. S.; Koleva, D. P.

    1982-01-01

    An attempt to cover all papers dealing with the hot atom chemistry of sulpphur is made. Publications which: a) only touch the problem, b) contain some data, indirectly connected with sulphur hot atom chemistry, c) deal with 35 S-production from a chloride matrix, are included as well. The author's name and literature source are given in the original language, transcribed, when it is necessary, in latine. A number of primery and secondary documents have been used including Chemical Abstracts, INIS Atomindex, the bibliographies of A. Siuda and J.-P. Adloff for 1973 - 77, etc. (authors)

  18. Are the lessons of the techno-economic studies on the sulphur-iodine cycle applicable to the other cycles?

    International Nuclear Information System (INIS)

    Werkoff, F.; Mansilla, C.

    2007-01-01

    Further advances in nuclear energy system design can broaden the opportunities for the use of nuclear energy. To explore these opportunities, several countries are involved in a forum on the development of next generation nuclear energy systems known as 'Generation IV'. Six concepts have been chosen by the forum, to be studied. The Very High Temperature Reactor (VHTR) offers perspectives for producing electricity and hydrogen with high efficiencies. Nuclear production of hydrogen by thermochemical means is one of the prime candidates for powering the hydrogen economy without producing green house gases. Among them, the Sulphur-Iodine (S-I) thermochemical cycle appeared well fitted with the VHTR, due to the temperature needed for the decomposition of the sulphuric acid. It was invented in the 1970's and it benefits from a revival of interest in the framework of Generation IV. In the last past years, assessments of the S-I process, coupled with a VHTR have been carried out. It appeared that these assessments have to be considered, looking with a particular care to the recommendations of the Generation IV crosscutting economics group [1]: a Generation IV system will: 1. Have a clear life-cost advantage over other energy systems. 2. Have a level of financial risk comparable to other energy projects. The experience gained from techno-economic studies [2, 3] which consider the S-I cycle, indicates that the choice of alternatives cycles to the S-I one must be driven by the characteristic of a previously selected nuclear reactor, mainly the temperature at the nuclear core outlet. Moreover, the net efficiency of the thermochemical cycle must be higher than a reference value defined from the alkaline electrolysis fed by the electricity produced from the selected reactor. Besides, the technical feasibility of the thermochemical processes is not yet established and the production cost of hydrogen from these processes is the result of the sum of several cost factors which are

  19. Effect of drought stress and sulphur fertilizer on quantity and quality yield of psyllium (Plantago ovata L. in Baluchestan

    Directory of Open Access Journals (Sweden)

    M. Mousavi nik

    2016-05-01

    Full Text Available Management of chemical fertilizers application is very important issues on environment and plant yield especially in arid and-semi arid region. In order to determine the effects of drought stresses and fertilizer levels on quantity and quality yields of psyllium (Plantago ovata L., a study was conducted as split plot based on randomized complete block design with four replications at the Natural Resources and Agriculture Researches Center of Balouchestan, Iran, during growing season of 2009-2010. Treatments included different irrigation regimes (three, five and eight times irrigation during the growing season as main plots and four levels of sulphur fertilizer (0, 75, 150 and 225 kg.ha-1 sulphur as sub plot. The results showed that the irrigation regimes and sulphur fertilizer had significant effects on seed and biological yield of psyllium, so the highest seed and biological yields obtained in eight times irrigation. Also, the maximum of these factors were achieved in 225 kg.ha-1 sulphur. The highest harvest index and 1000- seed weight, No. seed per spike and No. spike per plant were observed in eight times irrigation and 225 kg.ha-1 sulphur. The highest plant height was obtained in eight times irrigation and 225 kg.ha-1 sulphur and the maximum mucilage percentage and proline content were obtained in three times irrigation. The maximum mucilage yield and carbohydrate content were achieved in eight times irrigation. Among sulphur fertilizer, the highest amounts for all factors were achieved in 225 kg.ha-1 sulphur. There was positive and significant correlation between seed yield with spike No. per plant, Seed No. per spike, 1000-Seed, biological yield and mucilage yield.

  20. Impact of sulphurous water politzer inhalation on audiometric parameters in children with otitis media with effusion.

    Science.gov (United States)

    Mirandola, Prisco; Gobbi, Giuliana; Malinverno, Chiara; Carubbi, Cecilia; Ferné, Filippo M; Artico, Marco; Vitale, Marco; Vaccarezza, Mauro

    2013-03-01

    The positive effects of spa therapy on ear, nose, and throat pathology are known but robust literature in this field, is still lacking. The aim of this study was to assess through a retrospective analysis, the effects on otitis media with effusion of Politzer endotympanic inhalation of sulphurous waters in children aged 5-9 years. A cohort of 95 patients was treated with Politzer insufflations of sulphurous water: 58 patients did a cycle consisting of a treatment of 12 days per year for three consecutive years; 37 patients followed the same procedure for 5 years consecutively. The control population was represented by untreated, age-matched children. A standard audiometric test was used before and after each cycle of treatment. One cycle of Politzer inhalation of sulphur-rich water improved the symptoms. Three cycles definitively stabilized the improvement of hearing function. Our results show that otitis media with effusion in children can be resolved by an appropriate non-pharmacological treatment of middle ear with sulphur-rich water.

  1. Mesoporous iron–manganese oxides for sulphur mustard and soman degradation

    Energy Technology Data Exchange (ETDEWEB)

    Štengl, Václav, E-mail: stengl@iic.cas.cz [Department of Solid State Chemistry, Institute of Inorganic Chemistry AS CR, v.v.i., 250 68 Řež (Czech Republic); J.E. Purkyně University in Ústí nad Labem, Faculty of Environment, 400 96 Ústí nad Labem (Czech Republic); Grygar, Tomáš Matys [Department of Solid State Chemistry, Institute of Inorganic Chemistry AS CR, v.v.i., 250 68 Řež (Czech Republic); J.E. Purkyně University in Ústí nad Labem, Faculty of Environment, 400 96 Ústí nad Labem (Czech Republic); Bludská, Jana [Department of Solid State Chemistry, Institute of Inorganic Chemistry AS CR, v.v.i., 250 68 Řež (Czech Republic); Opluštil, František; Němec, Tomáš [Military Technical Institute of Protection Brno, Veslařská 230, 628 00 Brno (Czech Republic)

    2012-12-15

    Graphical abstract: Display Omitted Highlights: ► New nanodispersive materials based on Fe and Mn oxides for degradations of warfare agents. ► The best activities for the degradation of sulphur mustard (97.9% in 64 min) and soman (97.9% in 64 min). ► One pot synthesis with friendly transformed to industrial conditions. -- Abstract: Substituted iron(III)–manganese(III, IV) oxides, ammonio-jarosite and birnessite, were prepared by a homogeneous hydrolysis of potassium permanganate and iron(III) sulphate with 2-chloroacetamide and urea, respectively. Synthesised oxides were characterised using Brunauer–Emmett–Teller (BET) surface area and Barrett–Joiner–Halenda porosity (BJH), X-ray diffraction (XRD), infrared spectroscopy (IR), Raman spectroscopy and scanning electron microscopy (SEM). The oxides were taken for an experimental evaluation of their reactivity against sulphur mustard (HD) and soman (GD). When ammonio-jarosite formation is suppressed by adding urea to the reaction mixture, the reaction products are mixtures of goethite, schwertmannite and ferrihydrite, and their degradation activity against soman considerably increases. The best activities for the degradation of sulphur mustard (97.9% in 64 min) and soman (97.9% in 64 min) were observed for FeMn{sub 7}5 with 32.6 wt.% Fe (36.8 wt.% Mn) and FeMn{sub 3}7U with 60.8 wt.% Fe (10.1 wt.% Mn) samples, respectively.

  2. Mesoporous iron–manganese oxides for sulphur mustard and soman degradation

    International Nuclear Information System (INIS)

    Štengl, Václav; Grygar, Tomáš Matys; Bludská, Jana; Opluštil, František; Němec, Tomáš

    2012-01-01

    Graphical abstract: Display Omitted Highlights: ► New nanodispersive materials based on Fe and Mn oxides for degradations of warfare agents. ► The best activities for the degradation of sulphur mustard (97.9% in 64 min) and soman (97.9% in 64 min). ► One pot synthesis with friendly transformed to industrial conditions. -- Abstract: Substituted iron(III)–manganese(III, IV) oxides, ammonio-jarosite and birnessite, were prepared by a homogeneous hydrolysis of potassium permanganate and iron(III) sulphate with 2-chloroacetamide and urea, respectively. Synthesised oxides were characterised using Brunauer–Emmett–Teller (BET) surface area and Barrett–Joiner–Halenda porosity (BJH), X-ray diffraction (XRD), infrared spectroscopy (IR), Raman spectroscopy and scanning electron microscopy (SEM). The oxides were taken for an experimental evaluation of their reactivity against sulphur mustard (HD) and soman (GD). When ammonio-jarosite formation is suppressed by adding urea to the reaction mixture, the reaction products are mixtures of goethite, schwertmannite and ferrihydrite, and their degradation activity against soman considerably increases. The best activities for the degradation of sulphur mustard (97.9% in 64 min) and soman (97.9% in 64 min) were observed for FeMn 7 5 with 32.6 wt.% Fe (36.8 wt.% Mn) and FeMn 3 7U with 60.8 wt.% Fe (10.1 wt.% Mn) samples, respectively.

  3. Studies on uptake and translocation of sulphur in oil seed rape plant using 35S tracer technique

    International Nuclear Information System (INIS)

    Zhang Qinzheng; Wang Xiaochang

    1995-01-01

    The experiments were conducted to investigate the uptake and translocation of 35 S in oil seed rape at different stages. The results showed that uptake of sulphur from soil by rape plant were 23.59%, 31.65% and 49.13% of sulphur applied at transplanting, bolting and flowering stage, respectively. About 40% of 35 S taken from soil was located in seeds for transplanting and flowering stage applying. About 20% of sulphur applied on top four leaves at various stages of growth was remained in labelled leaves and 21%∼23% was transported to pods with majority in branch pods. 40%∼60% of sulphur which was applied on surface of pods at lower stem at different time after flowering was remained in shell of labelled pods and 13%∼16.8% of that was transferred into seeds of labelled pods. Recoveries of labelled sulphur applied on pods from seeds of pods at branches were less than 10%. The transportation of 35 S from labelled sites to seeds of labelled pods and unlabelled pods was declined sharply as labelling was carried out at 6 weeks after flowering

  4. Primordial helium abundance determination using sulphur as metallicity tracer

    Science.gov (United States)

    Fernández, Vital; Terlevich, Elena; Díaz, Angeles I.; Terlevich, Roberto; Rosales-Ortega, F. F.

    2018-05-01

    The primordial helium abundance YP is calculated using sulphur as metallicity tracer in the classical methodology (with YP as an extrapolation of Y to zero metals). The calculated value, YP, S = 0.244 ± 0.006, is in good agreement with the estimate from the Planck experiment, as well as, determinations in the literature using oxygen as the metallicity tracer. The chemical analysis includes the sustraction of the nebular continuum and of the stellar continuum computed from simple stellar population synthesis grids. The S+2 content is measured from the near infrared [SIII]λλ9069Å, 9532Å lines, while an ICF(S3 +) is proposed based on the Ar3 +/Ar2 + fraction. Finally, we apply a multivariable linear regression using simultaneously oxygen, nitrogen and sulphur abundances for the same sample to determine the primordial helium abundance resulting in YP - O, N, S = 0.245 ± 0.007.

  5. Certification of reference materials by energy-dispersive x-ray fluorescence spectrometry?

    DEFF Research Database (Denmark)

    Christensen, Leif Højslet; Heydorn, Kaj

    1985-01-01

    This paper studies the precision and accuracy that can be achieved using energy-dispersive x-ray fluorescence spectrometry for the determination of total sulphur content in BCR 38 Fly Ash issued by the European Community Bureau of Reference.......This paper studies the precision and accuracy that can be achieved using energy-dispersive x-ray fluorescence spectrometry for the determination of total sulphur content in BCR 38 Fly Ash issued by the European Community Bureau of Reference....

  6. effects of sulphur addition on addition on and mechanical properties

    African Journals Online (AJOL)

    User

    234-8034714355. 8034714355. 1. EFFECTS OF SULPHUR ADDITION ON. ADDITION ON. 2. AND MECHANICAL PROPERTIES O. 3. 4. C. W. Onyia. 5. 1DEPT. OF METALLURGICAL AND MATERIALS. 6. 2, 4DEPT. OF METALLURGICAL ...

  7. Chlorine- and Sulphur-substituted Pyrrolo[3,4-b]quinolines and ...

    African Journals Online (AJOL)

    Chlorine- and Sulphur-substituted Pyrrolo[3,4-b]quinolines and Related Derivatives .... J. Chem., 2003, 56, 40–46,. . .... It is evident from the above that by judicious selection and application of reagents ...

  8. Chemical and isotopic characteristics of geothermal fluids from Sulphur Springs, Saint Lucia

    Science.gov (United States)

    Joseph, Erouscilla P.; Fournier, Nicolas; Lindsay, Jan M.; Robertson, Richard; Beckles, Denise M.

    2013-03-01

    Sulphur Springs is a vigorous, geothermal field associated with the active Soufrière Volcanic Centre in southern Saint Lucia, Lesser Antilles island arc. The 'Sulphur Springs Park' is an important tourist attraction (touted as the 'world's only drive-through volcano') with some of the hot pools being developed into recreational pools. Some 200,000 people visit the park each year. Since 2001, the hydrothermal fluids of Sulphur Springs have been sampled as part of an integrated volcanic monitoring programme for the island. Gas and water samples were analysed to characterise the geochemistry of the hydrothermal system, and to assess the equilibrium state and subsurface temperatures of the reservoir. This has also enabled us, for the first time, to establish baseline data for future geochemical monitoring. The gases are of typical arc-type composition, with N2 excess and low He and Ar content. The dry gas composition is dominated by CO2 (ranging from 601-993 mmol/mol), with deeper magmatic sourced H2S-rich vapour undergoing boiling and redox changes in the geothermal reservoir to emerge with a hydrothermal signature in the fumarolic gases. Fluid contributions from magmatic degassing are also evident, mainly from the moderate to high contents of HCl and deeply-sourced H2S gas, respectively. Sulphur Springs hydrothermal waters have acid-sulphate type compositions (SO4 = 78-4008 mg/L; pH = 3-7), and are of primarily meteoric origin which have been affected by evaporation processes based on the enrichment in both δ18O and δD (δ18O = - 1 to 15‰ and δD = - 9 to 14‰ respectively) in relation to the global meteoric water line (GMWL). These waters are steam-heated water typically formed by absorption of H2S-rich gases in the near surface oxygenated groundwaters. Reservoir temperatures calculated from the evaluation of gas equilibria in the CO2-CH4-H2 system reveal higher temperatures (190 to 300 °C) than those derived from quartz geothermometry (95 to 169 °C), which

  9. Cellulose sulphuric acid as a biodegradable catalyst for conversion ...

    Indian Academy of Sciences (India)

    This article describes simple and efficient method for the diazotization and azidation of different aromatic amines over cellulose sulphuric acid, sodium nitrite and sodium azide under mild conditions at room temperature. Various aryl amines possessing electron-withdrawing groups or electron-donating groups have been ...

  10. Past and future trends in concentrations of sulphur and nitrogen compounds in the Arctic

    DEFF Research Database (Denmark)

    Hole, Lars R.; Christensen, Jesper H.; Ruoho-Airola, Tuija

    2009-01-01

    Recent trends in nitrogen and sulphur compounds in air and precipitation from a range of Arctic monitoring stations are presented, with seasonal data from the late 70s to 2004 or 2005. Earlier findings of declining sulphur concentrations are confirmed for most stations, while the pattern is less...... clear for reduced and oxidized nitrogen. In fact there are positive trends for nitrogen compounds in air at several stations. Acidity is generally reduced at many stations while the precipitation amount is either increasing or stable. Variability of sulphate concentrations in air for the period 1991......-2000 is reasonably well reproduced at most stations using an Eulerian, hemispherical model. Results for nitrogen compounds are weaker. Scenario studies show that even if large sulphur emission reductions take place in important source regions in South-East Asia in the coming decades, only small changes in Arctic...

  11. Continental scale Antarctic deposition of sulphur and black carbon from anthropogenic and volcanic sources

    Directory of Open Access Journals (Sweden)

    H.-F. Graf

    2010-03-01

    Full Text Available While Antarctica is often described as a pristine environment, there is an increasing awareness of the potential threats from local pollution sources including tourist ships and emissions associated with scientific activities. However, to date there has been no systematic attempt to model the impacts of such pollutants at the continental scale. Indeed, until very recently there was not even a sulphur emission budget available for Antarctica. Here we present the first comprehensive study of atmospheric pollution in Antarctica using a limited area chemistry climate model, and a monthly emissions inventory for sulphur from maintenance of research stations, ground and air traffic, shipping and the active Erebus volcano. We find that ship emissions, both sulphurous and black carbon, dominate anthropogenic pollution near the ground. Their prevalence is likely to rise dramatically if recent trends in tourism continue.

  12. Hvede, rug og triticale til energi - input, udbytte og kvalitet

    DEFF Research Database (Denmark)

    Jørgensen, Johannes Ravn

    2000-01-01

    Yield and quality of wheat, rye or triticale for energy purposes have been evaluated in field trials. Triticale and rye had a higher biomass production than wheat in spite of a lower input of nitrogen. The straw fraction contained more chloride, potassium and sodium than the grain fraction...... of chloride and sulphur in the straw as well as content of potassium, sodium and ash may be reduced due to precipitation before harvest........ These minerals may lead to corrosion processes, ash slagging and fouling. The grain fraction contained more sulphur and nitrogen, which may lead to emission of SO2 and NOx. Fertilizers containing chloride and sulphur, may lead to an increased content of chloride and sulphur in the straw fraction. Content...

  13. Bismuth ions are metabolized into autometallographic traceable bismuth-sulphur quantum dots

    Directory of Open Access Journals (Sweden)

    M Stoltenberg

    2009-06-01

    Full Text Available Bismuth – sulphur quantum dots can be silver enhanced by autometallography (AMG. In the present study, autometallographic silver enhanced bismuth-sulphur nanocrystals were isolated from unfixed cryo-sections of kidneys and livers of rats exposed to bismuth (Bi207 subnitrate. After being subjected to AMG all the organic material was removed by sonication and enzymatic digestion and the silver enhanced Bi- S quantum dots spun down by an ultracentrifuge and analyzed by scintillation. The analysis showed that the autometallographic technique traces approximately 94% of the total bismuth. This implies that the injected bismuth is ultimately captured in bismuthsulphur quantum dots, i.e., that Bi-S nanocrystals are the end product of bismuth metabolism

  14. Reactive extraction and recovery of levulinic acid, formic acid and furfural from aqueous solutions containing sulphuric acid

    NARCIS (Netherlands)

    Brouwer, Thomas; Blahusiak, Marek; Babic, Katarina; Schuur, Boelo

    2017-01-01

    Levulinic acid (LA) can be produced from lignocellulosic materials via hydroxylation followed by an acid-catalyzed conversion of hexoses. Inorganic homogeneous catalysts are mostly used, in particular sulphuric acid, yielding a mixture of LA with sulphuric acid, formic acid (FA) and furfural.

  15. [Sulphureous mud-bath therapy and changes in blood pressure: observational investigation].

    Science.gov (United States)

    Costantino, M; Marongiu, M B; Russomanno, G; Conti, V; Manzo, V; Filippelli, A

    2015-01-01

    The chronic arthropathies currently appear to be a major cause of disability with a negative impact on quality of life and health care spending. The mud-bath therapy is a spa treatment that induces benefic effects in chronic rheumatic diseases. It has long been debated on the assumption that the mud-bath spa therapy could have adverse cardiovascular effects which often induce caution and even a contraindication to the use of this treatment in chronic arthropathies associated with cardiovascular alterations such as hypertension. The aim of this observational study was to investigate, in arthrorheumatic subjects, the effects of sulphureous mud-bath cycle on blood pressure and the possible appearance of adverse drug reaction. 169 patients, with age range 42-86 years, suffering by chronic arthropathies were treated with sulphureous mud-bath therapy for 2 weeks. According to the arterial pressure values, measured before the spa treatment, the patients considered were divided in three groups: with normal blood pressure (NOR group); with high blood pressure, after, the latter group was divided in IPET (patients in treatment with antihypertensive drugs) and IPENT (patients not in antihypertensive therapy). The arterial pressure values, maximum and minimum, expressed in mmHg, were detected in the first (T1) - sixth (T6) and twelfth (T12) day of spa treatment. The media arterial pressure values collected before and after T1, before and after T6, before and after T12 , before T1 and after T12 were compared. The data, presented as mean±SD, were compared with the paired Student t test. A p value ≤0.05 was considered significant. The comparison between the mean values detected in pre and post T1, pre and post T6, pre and post T12 have showed that sulphureous mud-bath therapy induced a significant (pmud-bath therapy (post-T12) vs baseline (pre-T1) have demonstrated: in IPET and IPENT groups a significant (pmud-bath therapy in interdisciplinary therapeutic p rotocol of patients

  16. Velocity of crack growing of Inconel-600, sensitized, contaminated with sulphur in PWR type reactors

    International Nuclear Information System (INIS)

    Castano, M. L.; Blazquez, F.; Gomez Briceno, D.; Lagares, A.

    1998-01-01

    The origin of the vessel head penetration cracking of Jose Cabrera NPP has been attributed to an IGA/SCC process in a highly sensitized Alloy 600 assisted by sulphur species, as both acid sulphates and reduced species originated by the thermal breakdown of the cationic resins present in the primary coolant. The thermal degradation of the cationic resins leads sulphonic acid group scission and sulphates. Under the operating conditions the reduction of sulphates to sulphides is produced. The sulphides formed from the reduction of sulphate can precipitate with metallic cations and be incorporated into the oxide layers of the materials, preferably into nickel alloys. Others components at Jose Cabrera NPP are fabricated from sensitized alloy 600, as bottom vessel penetrations. In order to determine the influence of sulphur incorporated to the oxide layers of bottom vessel penetration alloy 600, an experimental work has been performed to obtained crack growth rate data under PWR primary conditions on sensitized alloy 600. (Author) 5 refs

  17. Use of acoustic emission technique to study the spalling behaviour of oxide scales on Ni-10Cr-8Al containing sulphur and/or yttrium impurity

    International Nuclear Information System (INIS)

    Khanna, A.S.; Quadakkers, W.J.; Jonas, H.

    1989-01-01

    It is now well established that the presence of small amounts of sulphur impurity in a NiCrAl-based alloy causes a deleterious effect on their high temperature oxidation behaviour. It is, however, not clear whether the adverse effect is due to a decrease in the spalling resistance of the oxide scale or due to an enhanced scale growth. In order to confirm which of the factors is dominating, two independent experimental techniques were used in the investigation of the oxidation behaviour of Ni-10Cr-8Al containing sulphur- and/or yttrium additions: conventional thermogravimetry, to study the scale growth rates and acoustic emission analysis to study the scale adherence. The results indicated that the dominant factor responsible for the deleterious effect of sulphur impurity on the oxidation of a Ni-10Cr-8Al alloy, was a significant change in the growth rate and the composition of the scale. Addition of yttrium improved the oxidation behaviour, not only by increasing the scale adherence, but also by reducing the scale growth due to gettering of sulphur. (orig.) [de

  18. Development of the floating sulphur biofilm reactor for sulphide ...

    African Journals Online (AJOL)

    driniev

    The formation of floating sulphur biofilm was observed in the microbial ecology studies of tannery ponds undertaken by the. Environmental Biotechnology Group at Rhodes University. This was related to the steep Redox gradients established at the air/ water interface of anaerobic, organically loaded and actively sulphate ...

  19. Reprint of “Experiences in sulphur capture in a 30 MWth Circulating Fluidized Bed boiler under oxy-combustion conditions”

    International Nuclear Information System (INIS)

    Gómez, M.; Fernández, A.; Llavona, I.; Kuivalainen, R.

    2015-01-01

    CO 2 and SO 2 from fossil fuel combustion are contributors to greenhouse effect and acid rain respectively. Oxy-combustion technology produces a highly concentrated CO 2 stream almost ready for capture. Circulating Fluidized Bed (CFB) boiler technology allows in-situ injection of calcium-based sorbents for efficient SO 2 capture. CIUDEN's 30 MWth CFB boiler, supplied by Foster Wheeler and located at the Technology Development Centre for CO 2 Capture and Transport (es.CO 2 ) in Spain, is the first of its kind for executing test runs at large pilot scale under both air-combustion and oxy-combustion conditions. In this work, SO 2 emissions under different scenarios have been evaluated. Variables such as limestone composition, Ca/S molar ratio and bed temperature among others have been considered along different test runs in both air-combustion and oxy-combustion conditions to analyse its influence on SO 2 abatement. Fly and bottom ash, together with flue gas analysis have been carried-out. Desulphurization performance tests results are presented. - Highlights: • Sulphur capture efficiency (%) was higher in oxy-combustion compared to air-combustion in a 30 MW thermal CFB boiler using anthracite and limestone as sulphur sorbent. • For a Ca/S molar ratio higher than 2.6 there was barely any improvement on sulphur capture efficiency for both air-combustion and oxy-combustion conditions in a 30 MW thermal CFB boiler using anthracite and limestone as sulphur sorbent. • Optimum temperature for sulphur capture at a fixed Ca/S molar ratio is around 880–890 °C under oxy-combustion conditions and for anthracite coal with limestone as sorbent in a 30 MW thermal CFB boiler

  20. Short communication: Laboratory approach to the use of sulphur and kaolin as preventive control against Drosophila suzukii

    Energy Technology Data Exchange (ETDEWEB)

    Pérez-Guerrero, S.; Molina, J.M.

    2016-11-01

    Drosophila suzukii (Matsumura, 1931) is an invasive pest from South East Asia that was detected for the first time in Southern Europe in 2008. This species can damage a wide range of soft-skinned fruits crops affecting ripening fruits and causing important economic losses. Since the exclusive use of chemical insecticides for controlling D. suzukii may prompt the appearance of resistance and environmental pollution, alternative methods compatible with sustainable management are required. In this study, commercial formulations of powdered sulphur and kaolin were tested as a preventive method applied to blueberry fruits under laboratory conditions. In no-choice assay, powdered sulphur had a significant effect on oviposition and adult emergency with reductions of 76% and 77%, respectively. In addition, sulphur displayed a significant toxicity on males and lethal effect with over 40% adult mortality seven days after exposure. The choice assay confirmed and improved the powdered sulphur effects, with reductions of 98% and 96% in oviposition and adult emergence, respectively. In contrast, kaolin produced no significant reduction in infestation and adult mortality during no-choice and choice assays. These outcomes suggest that preventive use of powdered sulphur could be considered for sustainable control of D. suzukii in some berry crops. (Author)

  1. Short communication: Laboratory approach to the use of sulphur and kaolin as preventive control against Drosophila suzukii

    Directory of Open Access Journals (Sweden)

    Sergio Pérez-Guerrero

    2016-06-01

    Full Text Available Drosophila suzukii (Matsumura, 1931 is an invasive pest from South East Asia that was detected for the first time in Southern Europe in 2008. This species can damage a wide range of soft-skinned fruits crops affecting ripening fruits and causing important economic losses. Since the exclusive use of chemical insecticides for controlling D. suzukii may prompt the appearance of resistance and environmental pollution, alternative methods compatible with sustainable management are required. In this study, commercial formulations of powdered sulphur and kaolin were tested as a preventive method applied to blueberry fruits under laboratory conditions. In no-choice assay, powdered sulphur had a significant effect on oviposition and adult emergency with reductions of 76% and 77%, respectively. In addition, sulphur displayed a significant toxicity on males and lethal effect with over 40% adult mortality seven days after exposure. The choice assay confirmed and improved the powdered sulphur effects, with reductions of 98% and 96% in oviposition and adult emergence, respectively. In contrast, kaolin produced no significant reduction in infestation and adult mortality during no-choice and choice assays. These outcomes suggest that preventive use of powdered sulphur could be considered for sustainable control of D. suzukii in some berry crops.

  2. ONCE GRAND, NOW FORGOTTEN: WHAT DO WE KNOW ABOUT THE SUPERHIGH-ORGANIC-SULPHUR RAŠA COAL?

    Directory of Open Access Journals (Sweden)

    Gordana Medunić

    2016-10-01

    Full Text Available The Istrian coal mines, located in the eastern part of the Istrian Peninsula (Northern Adriatic Sea, Croatia had by far the most important and economically the most valuable deposits of the anthracite coal reserves in Croatia since the 18th century until the year 1999, when their excavation and use in the coal-fired power plant Plomin ceased. The coal is found within the Palaeocene Kozina limestone beds. Four coal basins, Karojba, Sveti Martin, Pićan, and the Labin basin, hosted seven coal mines, e.g. Tupljak, Potpićan, Kozljak, Štrmac, Raša, Ripenda, and Krapan. The coal has been generally known under the name of Raša coal. It is exceptional in world terms due to its high content of organic sulphur, which can be up to 14%. Herewithin, this paper reviews Croatian scientific publications devoted to various aspects of Raša coal, along with the most important publications on either similar coals or relevant subjects worldwide. A brief introduction deals with the role of coal in electricity production, and the history of coal mining in Istria. The following chapter summarises current knowledge of the coal sulphur geochemistry, with several examples of high-sulphur coals from India and China. It is followed by the geological, geochemical, and physical characterisation of Raša coal. Since perturbations to ecosystems caused by coal combustion have been documented in numerous papers from a number of countries, Croatian studies carried out to determine the impact of Raša coal combustion on the local environment are also presented.

  3. In-situ Spectroscopic Studies and Modelling of Crystallization Processes of Sulphuric Acid Catalysts

    DEFF Research Database (Denmark)

    Oehlers, C.; Fehrmann, Rasmus; Masters, Stephen Grenville

    1996-01-01

    Deactivation of commercial and prototype sulphuric acid catalysts has been investigated in-situ by ESR spectroscopy. The influence of support pore structure,and the chemical composition of the catalyst and the gas phase was dicussed.A statistical lattice model was applied to describe the crystall......Deactivation of commercial and prototype sulphuric acid catalysts has been investigated in-situ by ESR spectroscopy. The influence of support pore structure,and the chemical composition of the catalyst and the gas phase was dicussed.A statistical lattice model was applied to describe...

  4. Sulphur simulations for East Asia using the MATCH model with meteorological data from ECMWF

    Energy Technology Data Exchange (ETDEWEB)

    Engardt, Magnuz

    2000-03-01

    As part of a model intercomparison exercise, with participants from a number of Asian, European and American institutes, sulphur transport and conversion calculations were conducted over an East Asian domain for 2 different months in 1993. All participants used the same emission inventory and simulated concentration and deposition at a number of prescribed geographic locations. The participants were asked to run their respective model both with standard parameters, and with a set of given parameters, in order to examine the different behaviour of the models. The study included comparison with measured data and model-to-model intercomparisons, notably source-receptor relationships. We hereby describe the MATCH model, used in the study, and report some typical results. We find that although the standard and the prescribed set of model parameters differed significantly in terms of sulphur conversion and wet scavenging rate, the resulting change in atmospheric concentrations and surface depositions only change marginally. We show that it is often more critical to choose a representative gridbox value than selecting a parameter from the suite available. The modelled, near-surface, atmospheric concentration of sulphur in eastern China is typically 5- 10 {mu}g S m{sup -3}, with large areas exceeding 20 {mu}g S m{sup -3}. In southern Japan the values range from 2-5 {mu}g S m{sup -3} . Atmospheric SO{sub 2} dominates over sulphate near the emission regions while sulphate concentrations are higher over e.g. the western Pacific. The sulphur deposition exceeds several g sulphur m{sup -2} year{sup -1} in large areas of China. Southern Japan receives 03-1 g S m{sup -2} year{sup -1}. In January, the total wet deposition roughly equals the dry deposition, in May - when it rains more in the domain - total wet deposition is ca. 50% larger than total dry deposition.

  5. Uptake and metabolism of sulphur dioxide by Arabidopsis thaliana

    NARCIS (Netherlands)

    van der Kooij, T.A.W.; De Kok, L.J.; Haneklaus, S.; Schnug, E.

    Arabidopsis thaliana (L.) Heynh. was exposed to various concentrations of SO2 during almost the entire life cycle. No negative effects of SO2 on shoot biomass production were observed. There was a linear relation between the deposition of SO2 and the atmospheric SO2 concentration. Sulphur

  6. Sources of increase in lowermost stratospheric sulphurous and carbonaceous aerosol background concentrations during 1999–2008 derived from CARIBIC flights

    Directory of Open Access Journals (Sweden)

    Johan Friberg

    2014-03-01

    Full Text Available This study focuses on sulphurous and carbonaceous aerosol, the major constituents of particulate matter in the lowermost stratosphere (LMS, based on in situ measurements from 1999 to 2008. Aerosol particles in the size range of 0.08–2 µm were collected monthly during intercontinental flights with the CARIBIC passenger aircraft, presenting the first long-term study on carbonaceous aerosol in the LMS. Elemental concentrations were derived via subsequent laboratory-based ion beam analysis. The stoichiometry indicates that the sulphurous fraction is sulphate, while an O/C ratio of 0.2 indicates that the carbonaceous aerosol is organic. The concentration of the carbonaceous component corresponded on average to approximately 25% of that of the sulphurous, and could not be explained by forest fires or biomass burning, since the average mass ratio of Fe to K was 16 times higher than typical ratios in effluents from biomass burning. The data reveal increasing concentrations of particulate sulphur and carbon with a doubling of particulate sulphur from 1999 to 2008 in the northern hemisphere LMS. Periods of elevated concentrations of particulate sulphur in the LMS are linked to downward transport of aerosol from higher altitudes, using ozone as a tracer for stratospheric air. Tropical volcanic eruptions penetrating the tropical tropopause are identified as the likely cause of the particulate sulphur and carbon increase in the LMS, where entrainment of lower tropospheric air into volcanic jets and plumes could be the cause of the carbon increase.

  7. On the formation of sulphuric acid – amine clusters in varying atmospheric conditions and its influence on atmospheric new particle formation

    Directory of Open Access Journals (Sweden)

    I. K. Ortega

    2012-10-01

    Full Text Available Sulphuric acid is a key component in atmospheric new particle formation. However, sulphuric acid alone does not form stable enough clusters to initiate particle formation in atmospheric conditions. Strong bases, such as amines, have been suggested to stabilize sulphuric acid clusters and thus participate in particle formation. We modelled the formation rate of clusters with two sulphuric acid and two amine molecules (JA2B2 at varying atmospherically relevant conditions with respect to concentrations of sulphuric acid ([H2SO4], dimethylamine ([DMA] and trimethylamine ([TMA], temperature and relative humidity (RH. We also tested how the model results change if we assume that the clusters with two sulphuric acid and two amine molecules would act as seeds for heterogeneous nucleation of organic vapours (other than amines with higher atmospheric concentrations than sulphuric acid. The modelled formation rates JA2B2 were functions of sulphuric acid concentration with close to quadratic dependence, which is in good agreement with atmospheric observations of the connection between the particle formation rate and sulphuric acid concentration. The coefficients KA2B2 connecting the cluster formation rate and sulphuric acid concentrations as JA2B2=KA2B2[H2SO4]2 turned out to depend also on amine concentrations, temperature and relative humidity. We compared the modelled coefficients KA2B2 with the corresponding coefficients calculated from the atmospheric observations (Kobs from environments with varying temperatures and levels of anthropogenic influence. By taking into account the modelled behaviour of JA2B2 as a function of [H2SO4], temperature and RH, the atmospheric particle formation rate was reproduced more closely than with the traditional semi-empirical formulae based on sulphuric acid concentration only. The formation rates of clusters with two sulphuric acid and two amine molecules with different amine compositions (DMA or TMA or one of both had

  8. [Therapeutic effect of the association between pulmonary ventilation and aerosol--inhalation with sulphureous mineral water in the chronic bronchopneumopathies].

    Science.gov (United States)

    Lopalco, M; Proia, A R; Fraioli, A; Serio, A; Cammarella, I; Petraccia, L; Grassi, M

    2004-04-01

    Our research evaluates the efficacy of the inalation therapy by mineral sulphureous water in patients suffering from cronic bronchopneumopathy. From August to October 2002, two groups of patients, randomly selected, suffering from cronic bronchopneumonopathy, were studied at spa center "Pompeo" in Ferentino (FR). Every patient was treated daily during a cycle of twelve days. The first group was treated by pneumonic mechanical ventilation associated to sulphureous water aerosolinalation, the second by mechanical pulmonary ventilation associated to sulphureous water aerosol-inalation medicated with flunisolide. Every patient carried out spirometry, before and after treatment, and the measurement of FEV1 was considered a good parameter to evaluate the respiratory function. All patients reported an improvement in symptoms as dyspnea and cough. Results obtained show a significant functional improvement of respiratory function in both groups, evaluated by FEV1. Equal efficacy treating the patients by medicated and not medicated treatments stress the therapeutic role of mineral sulphureous waters in chronic bronchopneumopathies. Our research points out the usefullness of pneumonic ventilation associated with sulphureous water aerosol-inalation in patients suffering from chronic bronchopneumopathies.

  9. Sulphur-containing compounds in the essential oil of Ferula alliacea roots and their mass spectral fragmentation patterns.

    Science.gov (United States)

    Kasaian, Jamal; Asili, Javad; Iranshahi, Mehrdad

    2016-10-01

    Context GC-MS analysis is the best way to characterize volatile sulphur-containing compounds. Ferula (Apiaceae) is a genus of perennial herbs. Due to the occurrence of essential oils or oleoresins in the Ferula species, these plants usually possess strong aromatic scent. Terpenoid compounds were the most abundant constituents of Ferula oils, however, in some of Ferula species, the essential oils were dominated by volatile sulphur-containing compounds. Objectives Ferula alliacea Boiss. is considered one of the sources of the oleo-gum-resin asafoetida. In this study, we analyzed the hydrodistilled essential oil from its dried roots and provide new data about retention indices and mass fragmentation patterns of some volatile sulphur-containing compounds that are useful for future studies on this class of compounds. Materials and methods The roots of F. alliacea were collected during the flowering stage of plant, from Bezgh, Kashmar to Neishabour road, Khorasan-Razavi province, Iran, in June 2012. The oil was obtained by hydrodistillation using a Clevenger apparatus and analyzed by GC-MS. Results This is the first report on phytochemical analysis of F. alliacea roots. Seventy-six components, representing 99.5% of the oil, were characterized. The major components were 10-epi-γ-eudesmol (22.3%), valerianol (12.5%), hinesol (8.3%), guaiol (7.3%) and Z-propenyl-sec-butyl trisulphide (6.5%). Predominant mass fragment ions of the identified sulphur-containing compounds are explained in this paper. Conclusion The volatile oil of F. alliacea mostly contains oxygenated sesquiterpenes, however, its odour was dominated by sulphur-containing compounds. The most abundant sulphur-containing compound includes Z-propenyl-sec-butyl trisulphide (6.5%).

  10. Effects of sulphuric acid, mechanical scarification and wet heat ...

    African Journals Online (AJOL)

    Effects of different treatment methods on the germination of seeds of Parkia biglobosa (mimosaceae) were carried out. Prior treatment of seeds with sulphuric acid, wet heat and mechanical scarification were found to induce germination of the dormant seeds. These methods could be applied to raise seedlings of the plant for ...

  11. Use of Hg-Electroplated-Pt Ultramicroelectrode for Determining Elemental Sulphur in Naphtha Samples

    Directory of Open Access Journals (Sweden)

    Carlos Eduardo de Andrade

    2012-01-01

    Full Text Available This paper describes the applicability of a Hg-electroplated-Pt ultramicroelectrode in the quantification of elemental sulphur in naphtha samples by square-wave voltammetry. A reproducible deposition methodology was studied and is reported in this paper. This methodology is innovative and relies on the quality of the mercury stock solution to obtain reproducible surfaces required for the analytical methodology. All analyses were performed using a Hg-electroplated-Pt ultramicroelectrode (Hg-Pt UME due to the low sensibility of such devices to ohmic drops in resistive solutions. The responses of the peak areas in voltammetric experiments were linear in all of the range studied. The method developed here is accurate and reproducible, with a detection limit of 0.010 mg L−1 and a good recovery range for both standard solutions of elemental sulphur (85 to 99% and real naphtha sample (79%. These results attest to the potential for the application of this electroanalytical methodology in determining elemental sulphur in naphtha samples containing mercaptans and disulphides.

  12. Gonadal cell kinetics in male mice treated with sulphur-35 during prenatal development

    International Nuclear Information System (INIS)

    Satyanarayana Reddy, K.; Reddy, P.P.; Reddi, O.S.

    1980-01-01

    Investigations on the possible hazards of the use of internally administered radioisotopes in human medicine either as therapeutic or diagnostic agents before or during child bearing age are of late gaining importance. The present investigation has been taken up to screen the effects of sulphur-35 on spermatogonia. CBA pregnant mice were injected (ip) with a dose of 20 μ Ci of sulphur-35 on 3.5, 10.5 or 15.5 days of gestation. At the similar intervals pregnant mice injected with physiological saline were kept for control data. All the animals were allowed to litter and F 1 male progeny were killed at maturity at the age of 10 weeks and the testes collected. Sections of both the testes were prepared and stained by PAS-haematoxylin technique and the survival of spermatogonia types A, Int and B and preleptotene spermatocytes was evaluated. There was a significant reduction in all the cell types in the sulphur-35 treated animals. Thus the results indicate the cell-killing effect of radionuclide. (auth.)

  13. Gonadal cell kinetics in male mice treated with sulphur-35 during prenatal development

    Energy Technology Data Exchange (ETDEWEB)

    Satyanarayana Reddy, K; Reddy, P P; Reddi, O S [Osmania Univ., Hyderabad (India). Inst. of Genetics

    1980-11-01

    Investigations on the possible hazards of the use of internally administered radioisotopes in human medicine either as therapeutic or diagnostic agents before or during child bearing age are of late gaining importance. The present investigation has been taken up to screen the effects of sulphur-35 on spermatogonia. CBA pregnant mice were injected (ip) with a dose of 20 ..mu.. Ci of sulphur-35 on 3.5, 10.5 or 15.5 days of gestation. At the similar intervals pregnant mice injected with physiological saline were kept for control data. All the animals were allowed to litter and F/sub 1/ male progeny were killed at maturity at the age of 10 weeks and the testes collected. Sections of both the testes were prepared and stained by PAS-haematoxylin technique and the survival of spermatogonia types A, Int and B and preleptotene spermatocytes was evaluated. There was a significant reduction in all the cell types in the sulphur-35 treated animals. Thus the results indicate the cell-killing effect of radionuclide.

  14. Pengaruh Nisbah Energi-Protein, Nitrogen-Sulfur dan Kalsium-Fosfor Terhadap Produk Metabolisme Rumen dan Kecernaan Substrat

    Directory of Open Access Journals (Sweden)

    S.N.O. Suwandyastuti

    2013-10-01

    Full Text Available Influence of the ratio of energy-protein, nitrogen-sulphur, and calsium-phosphor upon rumen metabolism product and digestibility of substrat ABSTRACT. The Rumen microbes are capable to digest the glucosa polymer of plant waste for energy source and can used the Non Protein Nitrogen (NPN for body protein synthesis, if the other precussor (Sulphur, Phospor and Branch Chain of Carbon are available.  To know the effectivity of the utilization of plant waste for energy, an experiment have been conducted by in vitro method, used the Randomized Black Design, four replication, factorial 33.  The factors tested are : (1 three levels of energy : protein (E/P ratio : 4, 5 and 6; (2 three levels of Nitrogen : Sulphur (N/Sratio: 7.5, 10 and 12.5; (3 three levels of Calsium : Phospor (Ca/P ratio : 0.5, 1 and 2. The variables measured are : synthesis of protein microbes (SPM ; production of Volatile Fatty Acid (VFA and Nitrogen Ammonia (N-NH3; the digestibility of substrat. Based on the all variable measured, the experiment can be concluded : (1 the effectivity of the utilization of rice straw will be increased if it used is fortified with 50 percent TDN as energy source (E/P=4, 0.20 percent dry matter of sulphur (N/S=10 and 0.0625 - 0.125 percent dry matter (DM of phospor (Ca/P=1.0 – 2.0; (2 To stimulate the activity of cellulolytic microbes, its need the fortification of sulphur until reach the optimum level (must be investigated.

  15. Future fuels: Canada's coast-to-coast network of refineries is emerging from a $3-billion-plus spending binge to take the lead in producing low sulphur gasoline

    International Nuclear Information System (INIS)

    Lunan, D.

    2004-01-01

    A series of investments to convert Canada's 22 operating refineries to produce low-sulphur gasoline are discussed. The investment involves more than $3-billion that will transform Canada's portfolio of aging refineries into one of the most efficient in the western world, and in the process reduce sulphur content in Canadian gasoline to 30 ppm. In some cases the refitting will be completed years ahead of the required 2005 deadline. Total refining capacity in Canada is about 2.5 million barrels per day of crude oil, which includes 580,000 barrels per day of capacity that is dedicated to upgrading bitumen into synthetic crude oil. The initiative to update the refineries was led by Irving Oil, which launched a one billion dollar refit of its 250,000 barrels per day Saint John refinery in the year 2000. Irving Oil's efforts were driven by the company's marketing program in the United States where regional fuel quality standards are higher than national standards either in Canada or the United States. Shell Canada and Imperial Oil are also on track to meet the 30 ppm sulphur level ahead of schedule. For example, Shell Canada is cooperating with Suncor Energy Products in the construction of a hydrotreater at Suncor's Sarnia refinery which will be used to reduce sulphur content of diesel from both the Shell and Suncor refineries, while Imperial Oil is investing over $520 million to refit its refineries in Alberta, Ontario and Nova Scotia. Petro-Canada too, has embarked on a $450 million capital program late in 2003 to introduce low sulphur gasoline; this was in addition to the $1.2 billion program to integrate its bitumen production, upgrading and refining operations. Ultramar launched its $300 million desulphurization program in late 2002; the project is now nearing completion. Refit of Ultramar's Jean Gaulin refinery on Quebec's South Shore will also include a 30,000 barrels per day continuous regeneration platformer to provide a second hydrogen source for the

  16. Physical and chemical processes of sulphur dioxide in the plume from an oil-fired power station

    International Nuclear Information System (INIS)

    Flyger, H.; Lewin, E.; Lund Thomsen, E.; Fenger, J.; Lyck, E.; Gryning, S.E.

    1977-03-01

    The Danish contribution to the EUROCOP COST 61a project is described. Work concerned the physical and chemical reactions of sulphur dioxide released from a power station. The investigation was based on the application of two tracers. Inactive, inert SF 6 is used to monitor the dispersion of and deposition from the plume; it was intended to use radioactive 35 SO 2 to determine the degree of oxidation of sulphur released from the stack; so far, however, public reaction has prevented the use of a release of activity in field experiments. The report describes the construction and testing of airborne instruments for continuous registration of sulphur dioxide, nitrogen oxides, ozone and the tracer SF 6 , as well as for measurements of temperature and humidity. Sulphur samples were collected on filter paper in a specially constructed low volume air sampler, and the subsequent chemical analysis in the laboratory is described. Finally, the problem of navigation is treated. It is shown that nitrogen oxides may be used as an internal tracer in plume experiments. Preliminary experiments based on inactive analysis only indicated an overall half-life for SO 2 in the plume of about half an hour. (author)

  17. Design and modeling of an advanced marine machinery system including waste heat recovery and removal of sulphur oxides

    DEFF Research Database (Denmark)

    Frimann Nielsen, Rasmus; Haglind, Fredrik; Larsen, Ulrik

    2013-01-01

    -stroke diesel engine and a conventional waste heat recovery system. The results suggest that an organic Rankine cycle placed after the conventional waste heat recovery system is able to extract the sulphuric acid from the exhaust gas, while at the same time increase power generation from waste heat by 32...... consists of a two-stroke diesel engine, the wet sulphuric process for sulphur removal and an advanced waste heat recovery system including a conventional steam Rankine cycle and an organic Rankine cycle. The results are compared with those of a state-of-the-art machinery system featuring a two...

  18. An evaluation of ambient sulphur dioxide concentrations from passive degassing of the Sulphur Springs, Saint Lucia geothermal system: Implications for human health

    Science.gov (United States)

    Joseph, Erouscilla P.; Beckles, Denise M.; Cox, Leonette; Jackson, Viveka B.; Alexander, Dominic

    2015-10-01

    Sulphur Springs Park in Saint Lucia is a site of energetic geothermal activity associated with the potentially active Soufrière Volcanic Centre. The Park is one of Saint Lucia's most important tourist attractions, and is marketed as the 'world's only drive-in volcano'. It has an on-site staff of tour guides and vendors, as well as over 200,000 visitors annually. There are also a number of residents living in the areas bordering the Park. Recreational use is made of the geothermal waters for bathing, application of mud masques, and in some cases drinking. As part of the University of the West Indies, Seismic Research Centre's (UWI-SRC's) overall volcano monitoring programme for Saint Lucia, the volcanic emissions at Sulphur Springs (hot springs, mud pools and fumaroles) have been regularly monitored since 2001. In recent years, visitors, staff, and management at the Park have expressed concern about the health effects of exposure to volcanic emissions from the hydrothermal system. In response to this, SRC has expanded its regular geothermal monitoring programme to include a preliminary evaluation of ambient sulphur dioxide (SO2) concentrations in and around the Park, to assess the possible implications for human health. Passive diffusion tubes were used to measure the atmospheric SO2 concentrations at various sites in Sulphur Springs Park (SSP), in the town of Soufrière and in the capital of Castries. Measurements of average monthly ambient SO2 with the passive samplers indicated that during the dry season period of April to July 2014 concentration at sites closest to the main vents at SSP (Group 1), which are routinely used by staff and visitors, frequently exceeded the WHO 10-minute AQG for SO2 of 500 μg/m3. However, for sites that were more distal to the main venting area (Groups 2 and 3), the average monthly ambient SO2 did not exceed the WHO 10-minute AQG for SO2 of 500 μg/m3 during the entire monitoring period. The measured concentrations and dispersion

  19. Effect of irrigation frequency and application levels of sulphur ...

    African Journals Online (AJOL)

    A field experiment was conducted at Indian Agricultural Research Institute, New Delhi during the crop season of 2007 to 2008 and 2008 to 2009 to study the effect of irrigation and sulphur on yield and water use efficiency of Indian mustard (Brassica juncea var. PusaJagannath). The experiment was carried out in split plot ...

  20. A comparison of decontamination effects of commercially available detergents in rats pre-exposed to topical sulphur mustard.

    Science.gov (United States)

    Misik, Jan; Jost, Petr; Pavlikova, Ruzena; Vodakova, Eva; Cabal, Jiri; Kuca, Kamil

    2013-06-01

    The genotoxic vesicant sulphur mustard [bis-2-(chloroethyl)sulphide] is a chemical warfare agent which is easily available due to its relatively simple synthesis. Thus, sulphur mustard is a potential agent for mass contamination. In this study, we focused on sulphur mustard toxicity and decontamination in a rat model using commercially available detergent mixtures for dermal decontamination. Male Wistar rats were percutaneously treated with sulphur mustard and subjected to wet decontamination 2 min postexposure. Commercially produced detergents Neodekont™, Argos™, Dermogel™ and FloraFree™ were tested for their decontamination efficacy against an exposed group and their protective ratios determined. The results showed that all tested detergent solutions produced an increase in the median lethal dose [LD(50) = 9.83 (5.87-13.63) mg·kg(-1)] in comparison to controls, which led to increased survival of experimental animals. In general, all tested detergents provided modest decontamination efficacy (PR = 2.0-5.7). The highest protective ratio (5.7) was consistently achieved with Argos™. Accordingly, Argos™ should be considered in further investigation of mass casualty decontamination.

  1. Means of supply of extremely low-sulphur oil to the power plants of Stenungsund and Karlshamn

    International Nuclear Information System (INIS)

    1986-10-01

    The power plants in question are estimated to produce 10 TWh electric power per year and use about 2.4 Mtons of heavy fuel oil. This will imply a considerable increase of emission of acidifying sulphur oxides. The report discusses the cost of supplying low-sulphur fuel oils. The cost is compared with the cost of the installation of desulphurization of flue gas, oils or gasification

  2. SULPHUR AVAILABILITY IN BRAZILIAM SOILS: RESPONSE TO SULPHUR FERTILIZING IN PRESENCE AND AUSENCE OF LIMING DISPONIBILIDADE DE ENXOFRE EM SOLOS BRASILEIROS: RESPOSTA À ADUBAÇÃO SULFATADA NA PRESENÇA E AUSÊNCIA DE CALAGEM

    Directory of Open Access Journals (Sweden)

    Eurípedes Malavolta

    2007-09-01

    Full Text Available

    A greenhouse experiment was carried out with surface samples of 12 soils from the States of São Paulo, Minas Gerais and Goiás (Brazil. Carbon (C content varied from 0.50 to 3.03%, sulphur from 0.0104 to 0.0319% and clay varied from 8 to 60%. Corn (Zea mays L. was grown in two successive croppings in presence of three rates of S (0, 20 and 40 ppm applied as gypsum, previously incubated in presence and absence of lime. Dry matter production did not show significant difference due to the two croppings of the soils; sulphur uptake, otherwise, was thoroughly lower in the second cropping, indicating the depletion of native and applied sulphur. Sandy soils have a lower supplying power of sulphur due to its effective small reserve. Clayey soils, moreover “cerrado” soils with higher carbon contents, possess greater croppings and sulphur uptake potentials, provided the soil acidity is neutralized. Liming, besides its role as soil acidity neutralizer and as calcium and magnesium supplier, showed positive interaction with sulphur and a synergistic effect on the depletion of soils native sulphur. The rates of sulphur which maximized dry matter yield and sulphur absorption varied in the range of 20 to 70 ppm, being the highest requirements found in clayey soils with no liming.

    Conduziu-se um experimento em casa de vegetação com amostras superficiais de 12 solos, provenientes dos Estados de São Paulo, Minas Gerais e Goiás (Brasil, com teores de carbono variando entre 0,5 e 3,03%, de enxofre total entre 0,0104 e 0,319% e de argila entre 8 e 60%. Os solos foram submetidos a dois cultivos sucessivos com milho (Zea mays L., com os tratamentos: 12 solos, 3 doses de gesso (0, 20 e 40 ppm de S, previamente incubados na ausência e presença de calagem. A produção de matéria seca da parte a

  3. Effect of elemental sulphur and compost on pH, electrical ...

    African Journals Online (AJOL)

    Safir

    2012-01-19

    Jan 19, 2012 ... 42/34. T.N.V. 4.5. P (mg kg-1) ... and extracted with 2.0 M HCl) were measured with similar methods ... react with carbonate in calcareous soil and neutralize it. Neilson ... oxidation in soil, the sulphuric acid formed reacted with.

  4. effects of sulphur addition on addition on and mechanical properties

    African Journals Online (AJOL)

    User

    on the microstructure and mechanical properties of sand cast been investigated ... owed that the addition of sulphur to Al-12wt%Si alloy. 12wt%Si alloy .... 28 materials. 29. Element. Aluminum. Silicon. Al. Si. Ca. Fe. Cu. Zn. Mn. Mg. Cr. B. 99.71.

  5. Effect of dietary molybdenum and sulphur on the copper status of ...

    African Journals Online (AJOL)

    in all groups receiving supplementary Mo. A dietary supplement of 70 mg Mo for a restricted period is ... Keywords: Sheep nutrition, copper toxicity, molybdenum toxicity, sulphur. ..... observation supports the suggestion by Dick, et af. (1975).

  6. Mantle to surface degassing of carbon- and sulphur-rich alkaline magma at El Hierro, Canary Islands

    Science.gov (United States)

    Longpré, Marc-Antoine; Stix, John; Klügel, Andreas; Shimizu, Nobumichi

    2017-02-01

    Basaltic volcanoes transfer volatiles from the mantle to the surface of the Earth. The quantification of deep volatile fluxes relies heavily on estimates of the volatile content of primitive magmas, the best archive of which is provided by melt inclusions. Available data from volcanoes producing mafic alkaline lavas in a range of tectonic settings suggest high volatile fluxes, but information remains sparse, particularly for intraplate ocean islands. Here we present measurements of volatile and trace element concentrations, as well as sulphur speciation, in olivine-hosted melt inclusions and matrix glasses from quenched basanite lava balloon samples from the 2011-2012 submarine eruption at El Hierro, Canary Islands. The results reveal remarkably high concentrations of dissolved volatiles and incompatible trace elements in this magma, with ∼80 ppm Nb and up to 3420 ppm CO2, 3.0 wt.% H2O and 5080 ppm S. Reconstructed primitive CO2 contents, considering CO2/Nb systematics and possible CO2 sequestration in shrinkage bubbles, reach weight percent levels, indicating that carbon is a major constituent of Canary Island magmas at depth and that exsolution of a CO2-rich fluid begins in the mantle at pressures in excess of 1 GPa. Correlations between sulphur concentration, sulphur speciation and water content suggest strong reduction of an initially oxidised mantle magma, likely controlled by coupled H2O and S degassing. This late-stage redox change may have triggered sulphide saturation, recorded by globular sulphide inclusions in clinopyroxene and ulvöspinel. The El Hierro basanite thus had a particularly high volatile-carrying capacity and released a minimum of 1.3-2.1 Tg CO2 and 1.8-2.9 Tg S to the environment, causing substantial stress on the local submarine ecosystem. These results highlight the important contribution of alkaline ocean island volcanoes, such as the Canary Islands, to volatile fluxes from the mantle.

  7. Eco-restoration of a high-sulphur coal mine overburden dumping site in northeast India: A case study

    Science.gov (United States)

    Dowarah, J.; Deka Boruah, H. P.; Gogoi, J.; Pathak, N.; Saikia, N.; Handique, A. K.

    2009-10-01

    Eco-restoration of mine overburden (OB) or abandoned mine sites is a major environmental concern. In the present investigation, an integrated approach was used to rejuvenate a high-sulphur mine OB dumping site in the Tirap Collieries, Assam, India, which is situated in the Indo-Burma mega-biodiversity hotspot. A mine OB is devoid of true soil character with poor macro and micronutrient content and contains elevated concentrations of trace and heavy metals. Planting of herbs, shrubs, cover crops and tree species at close proximity leads to primary and secondary sere state succession within a period of 3 to 5 years. A variety of plant species were screened for potential use in restoration: herbs, including Sccharum spontaneum, Cymbopogon winterianus Jowitt (citronella), and Cymbopogon flexuosus (lemon grass) cover plants, including Mimosa strigillosa, M. striata, and M. pigra; shrubs, including Sesbania rostrata (dhaincha) and Cassia streata (cassia); and tree species, including Gmelina arborea (gomari) and Dalbergia sissoo (sissoo). Amendment with unmined soil and bio-organic matter was required for primary establishment of some plant species. Management of these plant species at the site will ensure long term sustainable eco-restoration of the coal mine-degraded land.

  8. Eco-restoration of a high-sulphur coal mine overburden dumping site in northeast India: A case study

    Energy Technology Data Exchange (ETDEWEB)

    Dowarah, J.; Boruah, H.P.D.; Gogoi, J.; Pathak, N.; Saikia, N.; Handique, A.K. [CSIR, Jorhat (India). North East Institute of Science & Technology

    2009-10-15

    Eco-restoration of mine overburden (OB) or abandoned mine sites is a major environmental concern. In the present investigation, an integrated approach was used to rejuvenate a high-sulphur mine OB dumping site in the Tirap Collieries, Assam, India, which is situated in the Indo-Burma mega-biodiversity hotspot. A mine OB is devoid of true soil character with poor macro and micronutrient content and contains elevated concentrations of trace and heavy metals. Planting of herbs, shrubs, cover crops and tree species at close proximity leads to primary and secondary sere state succession within a period of 3 to 5 years. A variety of plant species were screened for potential use in restoration: herbs, including Sccharum spontaneum, Cymbopogon winterianus Jowitt (citronella), and Cymbopogon flexuosus (lemon grass) cover plants, including Mimosa strigillosa, M. striata, and M. pigra; shrubs, including Sesbania rostrata (dhaincha) and Cassia streata (cassia); and tree species, including Gmelina arborea (gomari) and Dalbergia sissoo (sissoo). Amendment with unmined soil and bio-organic matter was required for primary establishment of some plant species. Management of these plant species at the site will ensure long term sustainable eco-restoration of the coal mine-degraded land.

  9. A METHODOLOGY BASED ON AN ECOLOGICAL ECONOMY APPROACH FOR THE INTEGRATING MANAGEMENT OF THE SULPHUROUS WATER IN AN OIL REFINERY

    Directory of Open Access Journals (Sweden)

    Gabriel Orlando Lobelles Sardiñas

    2016-10-01

    Full Text Available Despite the current highly stringent international standards regulating the contaminating emissions to the environment, the Oil refinery of Cienfuegos is still generating liquid and gaseous emissions contaminating the environment. The construction of new units as part of the Refinery expansion leads to an increase of these emissions due to the lack of technologies for the reutilization of the sulphurous water. The objective of this paper is to propose a methodology for the integral management of the sulphurous residual water in the oil refining process, including the evaluation and selection of the most feasible technological variant to minimize the sulphur contamination of water and the resulting emissions during the process. The methodology is based on the ecological economy tools, allowing a comprehensible evaluation of six technological variants at the refinery of Cienfuegos. The Life Cycle Assessment was applied (ACV by its Spanish acronym, by means of the software SimaPro 7.1. It was evaluated through the Eco Speed Method, to minimize the possible uncertainty. An economic evaluation was performed, taking into account the external costs for a more comprehensive analysis, enabling, along with the ecological indicators, the selection of the best technological variant, achieving a methodology based on a comprehensive evaluation, and as a positive impact, the implementation of the chosen variant (V5, 98.27% of the process water was recovered, as well as the sulphur that recovered from 94 to 99.8 %, reducing the emissions from 12 200 to 120 mg/Nm3 as SO2.

  10. Distribution of Sulphur in Soils Formed from Different Parent ...

    African Journals Online (AJOL)

    ABSTRACT: A study on the profile distribution of sulphate - sulphur (SO4-S) and the relationship with some soil properties was carried out in three ... Aluminum, content and nature of organic matter, pH and the presence of other ions. ... were extracted using 1N neutral ammonium acetate. (NH4OAC) and Ca and Mg was ...

  11. Quantification of chemical sulphur species in bulk soil and organic sulphur fractions by S K-edge Xanes spectroscopy

    DEFF Research Database (Denmark)

    Boye, K; Almkvist, G; Nilsson, S I

    2011-01-01

    residue (CR) incorporation and farmyard manure (FYM) application, with equal applications of mineral nutrients were included in the study. In the new data treatment method, internally calibrated spectra of dilute solutions (30 mm) of model compounds were used to fit the sample spectra. This greatly...... the opposite trend was observed. Sulphur XANES spectroscopy of acetylacetone extracts of physically protected and unprotected organic S in two of the soils revealed that physical protection was not related to S speciation; however, intermediate forms of oxidized S species appeared to accumulate in the residual...

  12. Sodium-sulphur batteries for electric road vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Mangan, M.F. (Chloride Silent Power Ltd., Runcorn (UK))

    1989-04-01

    The sodium sulphur couple is, in principle, very well behaved and has operational characteristics which make it ideal for electric vehicle use. Design of the battery system for road use requires that a number of practical considerations are addressed. In particular, the battery operates at 350 deg C and requires a thermal enclosure with thermal management. The cell interconnection network must address the consequences of end-of-life failure and the voltages across the individual cells should be limited, both in charge and discharge. (author).

  13. Exposure of CR39 Stacks to Oxygen and Sulphur Beams at the CERN-SPS

    CERN Multimedia

    2002-01-01

    We plan to expose 8 stacks of CR39 sheets to oxygen and sulphur ions of 60 and 200~GeV at the CERN-SPS.\\\\ \\\\ The main purpose of the exposures is the calibration of the CR39 sheets used for a large area experimental search for magnetic monopoles at the Gran Sasso Laboratory (experiment MACRO). \\\\ \\\\ The stacks have 20~layers of CR39, each layer 13~cm~x~7~cm and 1.4~mm thick. A copper absorber is located after the first 6 layers. \\\\ \\\\ We require exposures of about 2000 tracks per cm$^2$ over the entire area of the stack with a uniform illumination. The standard beam used for the emulsion experiments is normally adequate for this purpose.\\\\ \\\\ We have performed one exposure to sulphur ions. The etched tracks have been measured automatically with the Elbeck image analyser system. We measured the incoming sulphur ions as well as the nuclear fragments produced in the copper absorber. Clean separation among the peaks due to the various fragments is obtained (there is no indication of nuclei with fractional electri...

  14. Optimization of growth parameters of hydrogenated amorphous silicon-sulphur alloys

    International Nuclear Information System (INIS)

    Al-Dallal, S.; Aljishi, S.; Arekat, S.; Al-alawi, S.M.; Hammam, H.

    1995-01-01

    Hydrogenated amorphous silicon sulphur thin films were grown by capacitively coupled radio frequency glow discharge decomposition of SiH/sub 4/ + He) and H/sub 2/S + He) gas mixtures. In this work we report on a study undertaken to instigative the effect of deposition conditions on the optoelectronic properties of a-Si,S:H films. Three series of deposition conditions on the optoelectronic properties of a-Si,S:H films. Three series of films were prepared using a constant flow rate of the gaseous mixture while varying one of the other deposition parameters: substrate temperature, RF powder and process pressure. The films are characterized via IR measurements, optical transmission, photothermal deflection spectroscopy, photoluminescence, the constant photocurrent methods and conductivity measurements. Results indicate that a relatively high power level and a high substrate temperature are necessary to obtain the best films. (author) 8 figs

  15. Growth of Sulphuric Acid Nanoparticles Under Wet and Dry Conditions

    Czech Academy of Sciences Publication Activity Database

    Škrabalová, Lenka; Brus, David; Antilla, T.; Ždímal, Vladimír; Lihavainen, H.

    2014-01-01

    Roč. 14, č. 12 (2014), s. 6461-6475 ISSN 1680-7316 R&D Projects: GA AV ČR IAA200760905 Grant - others:AFCEP(FI) 1118615 Institutional support: RVO:67985858 Keywords : binary nucleation * sulphuric acid - water * condensational growth Subject RIV: BJ - Thermodynamics Impact factor: 5.053, year: 2014

  16. Nuclear accident dosimetry: the calibration of Geiger-Mueller and 2π proportional counters for sulphur and gold

    International Nuclear Information System (INIS)

    Delafield, H.J.; Reading, A.H.

    1981-10-01

    A reference, 2π precision counter was set up at Harwell and absolutely calibrated for the measurement of sulphur discs ( 32 P) and gold foils ( 198 Au) used in the UK personnel criticality dosimeter. Sample sulphur discs and gold foils were irradiated in the GLEEP reactor at Harwell, counted in the 2π counter, and their activities absolutely assayed by the National Physical Laboratory. The 2π counter was then used to intercalibrate the GM counters used routinely for the assessment of the criticality dosimeter. The mean measured efficiencies of the GM counters were found to be for 32 P in sulphur discs within +- 4%, and for gold ( 198 Au) within +- 6% of the values given by previous calibrations. (author)

  17. Modelling of catalytic oxidation of NH3 and reduction of NO on limestone during sulphur capture

    DEFF Research Database (Denmark)

    Kiil, Søren; Bhatia, Suresh K.; Dam-Johansen, Kim

    1996-01-01

    activity with respect to each species involved. An existing particle model, the Grain-Micrograin Model, which simulates sulphur capture on limestone under oxidizing conditions is considered in the modelling. Simulation results in good qualitative agreement with experimental data are obtained here......A theoretical study of the complex transient system of simultaneous sulphur capture and catalytic reactions of N-containing compounds taking place on a single limestone particle is conducted. The numerical technique developed previously by the authors (Kiil et al. 1994) based on collocation...... for the catalytic chemistry of NH3 during simultaneous sulphur capture on a Stevns Chalk particle. The reduction of NO by NH3 over CaSO4 (which is the product of the reaction between SO2, O2 and limestone) was found to be important because this reaction could explain the change in selectivity with increased solid...

  18. Evaluation of Plants and Weeds Extract on the Corrosion Inhibition of Mild Steel in Sulphuric Acid

    Directory of Open Access Journals (Sweden)

    Abida Begum

    2011-01-01

    Full Text Available Experiments were performed in order to determine the inhibitive effects of extracts of plants and weeds namely Parthenium hysterophorus, Dathura stromonium, Azadirachta indica, Helianthus annuus leaves extract for mild steel in sulphuric acid by using weight loss and thermometric technique. Results demonstrated that, all the experimental inhibitors show an adsorption on steel surface according to Langmuir’s isotherm. The inhibition efficiency increased with increase in the concentration of all tested inhibitors to attain a maximum value at 1.0%. Free energy values for adsorption process show that the process is spontaneous. The kinetic treatment of the results shows first order kinetics.

  19. Three-decade changes in chemical composition of precipitation in Guangzhou city, southern China: has precipitation recovered from acidification following sulphur dioxide emission control?

    Directory of Open Access Journals (Sweden)

    Yunting Fang

    2013-09-01

    Full Text Available We examined if precipitation had recovered from acidification in Guangzhou, the third biggest city in China, and if sulphur deposition in precipitation had decreased, and to what extent if yes, following abatement strategies in sulphur dioxide (SO2 emission and energy use implemented since 2001. SO2 emissions were decreasing steadily since 2001, but a marked recovery of precipitation acidity occurred only since 2005; precipitation pH values decreased from 4.65 in 2001 to 4.34 in 2005 and then increased to 5.08 in 2010, while in the same period acid rain (pH<5.6 frequency increased from 70% to 81% and then decreased to 48%. During this period, the change in pH value and sulphate concentration more reflected the patterns of SO2 emission at provincial and national scales than at the local scale, suggesting that precipitation chemical composition was largely controlled by the emissions of pollutants from surrounding areas of the study city. Since 2001, sulphate deposition in precipitation decreased significantly (by 40% but nitrogen deposition remained unaltered. More importantly, the current sulphur (43 kg S ha−1 yr−1 as sulphate and nitrogen depositions (35 kg N ha−1 yr−1 as ammonium plus nitrate in 2010 were still among the highest in China. These results highlight the fact that ambient sulphur and nitrogen deposition still pose a threat to the health of both terrestrial and aquatic ecosystems. Precipitation may become more acidified in the future because the deposition of alkaline dusts containing calcium is also likely to decrease with stricter SO2 emission control policy and reduced construction activities. Additionally, we recommend that a reduction of emissions of nitrogen and chlorine bearing pollutants is urgently required for complete control on acid deposition.

  20. Increased energy efficiency and the rebound effect: Effects on consumption and emissions

    International Nuclear Information System (INIS)

    Braennlund, Runar; Ghalwash, Tarek; Nordstroem, Jonas

    2007-01-01

    The main objective of this paper is to examine how exogenous technological progress, in terms of an increase in energy efficiency, affects consumption choice by Swedish households and thereby emissions of carbon dioxide (CO 2 ), sulphur dioxide (SO 2 ) and nitrogen oxide (NO x ). The aim of the paper is closely related to the discussion of what is termed the 'rebound effect'. To neutralise the rebound effect, we estimate the necessary change in CO 2 tax, i.e. the CO 2 tax that keeps CO 2 emissions at their initial level. In addition, we estimate how this will affect emissions of sulphur dioxide and nitrogen oxides. The results indicate that an increase in energy efficiency of 20% will increase emissions of CO 2 by approximately 5%. To reduce the CO 2 emissions to their initial level, the CO 2 tax must be raised by 130%. This tax increase will reduce the emissions of sulphur dioxide to below their initial level, but will leave the emissions of nitrogen oxides at a higher level than initially. Thus, if marginal damages from sulphur dioxide and nitrogen dioxide are non-constant, additional policy instruments are needed

  1. Sulphur extended oil sand mix : paving material for lower transport cost and CO{sub 2} reduction : ASRL Syncrude research project 1995

    Energy Technology Data Exchange (ETDEWEB)

    Aquin d' , G. [Con-Sul Inc., Missoula, MT (United States)

    2010-07-01

    This power point presentation discussed the use of sulphur-enhanced oil sands (SEOS) as a paving mixture. Sulphur has been added to asphaltic bitumen paving processes since the 1850s. Research into sulphur additions has been conducted by various Canadian industry members and institutions. A study in 1995 investigated the use of SEOS as a temporary paving material. The benefits of using SEOS included lower capital costs and lower greenhouse gas (GHG) impacts. Increases in equipment efficiency were also observed. Researchers are now developing mixing protocols and testing various paving materials in relation to temperature regimes and percentages of sulphur. Sand, limestone, coke, and rubber additions are also being evaluated, as well as the behaviour of SEOS in freeze-thaw cycles. To date, the studies have indicated that a 30 percent sulphur, 10 percent sand, and 60 percent oil sand mixture provides optimal compression and behaviour under freeze-thaw conditions. The use of SEOS paving at oil sands mine sites will reduce truck and road maintenance as well as reduce fuel emissions and consumption rates. tabs., figs.

  2. Effect of oxygen potential on sulphur dioxide activation of oil sands fluid coke and characteristics of activated coke in mercury adsorption

    International Nuclear Information System (INIS)

    Morris, E.A.; Jia, C.Q.; Tong, S.

    2007-01-01

    A sulphur-impregnated activated carbon (SIAC) technology was modified for use in copper smelters in order to mitigate mercury and sulphur dioxide (SO 2 ) emissions. Elemental sulphur was captured as a co-product. The study examined the feasibility of reducing levels of SO 2 using fluid coke in the copper smelter flue. SIAC properties were optimized in order to capture vapour phase mercury. Raw fluid coke samples were used to measure SO 2 flow rates. Gas composition was varied to mimic concentrations found during normal operation of copper converters. Gas chromatography was used to analyze reactions products and to prove the hypothesis that mercury capacity is influenced by the oxygen potential of the activation gas due to changes in surface sulphur types developed from reduced sulphur species. Results of the study showed that oxygen levels at 5 per cent did not play a significant role in pore development. It was concluded that increased residence times contributed to reductions in SO 2 and elemental S yields. 13 refs., 1 tab., 7 figs

  3. Modelling the fate of sulphur-35 in crops. 1. Calibration data

    International Nuclear Information System (INIS)

    Collins, Chris; Cunningham, Nathan

    2005-01-01

    Gas-cooled nuclear power plants in the UK release sulphur-35 during their routine operation. The gas is in the form of COS which can be readily assimilated by vegetation. It is therefore necessary to be able to model the uptake of such releases in order to quantify any potential contamination of the food chain. To develop such models experimental data are required. A series of experiments was undertaken to determine the rate of deposition, the partition and subsequent loss of sulphur-35 in crops exposed to CO 35 S. The mass normalised deposition rate was similar for the range of crops tested, while the partition of the 35 S paralleled the growth of crop components. There was no significant loss of radioactivity other than that expected from radioactive decay. - The deposition, fate and loss of 35 S in crops were quantified following exposure to COS

  4. Synergetic effect of sulphur and nitrogen oxides on corrosion of ...

    African Journals Online (AJOL)

    The synergetic effect of nitrogen dioxide (NO2) and sulphur dioxide (SO2) on corrosion of galvanized iron roofing sheets has been investigated. The field studies were conducted in Ibeno and Ebocha (Niger Delta, Nigeria). Specimens of the roofing sheets were exposed for one year to outdoor environment to record the ...

  5. Assessment of pollution due to oxides of sulphur and nitrogen at Tarapur

    International Nuclear Information System (INIS)

    Sudheendran, V.; Pimple, K.G.; Rao, D.D.; Chandramouli, S.; Iyer, R.S.; Hegde, A.G.

    1995-01-01

    An Environmental Survey Laboratory (ESL) was established in 1964 to monitor and assess the dispersion of radioactive releases from the power station in the environmental matrices. ESL has been making measurements of ambient sulphur dioxide concentration in the atmosphere at a few selected locations since 1984. The residential areas which are in the vicinity of the chemical zone experience acute effects of sulphur dioxide pollution from time to time depending upon the seasonal variations of meteorological parameters. The proposed commissioning of a thermal power station in the region (Dahanu) gives added importance to the estimation of SO 2 and NO 2 concentrations in the atmosphere. The paper presents data and assessment of the prevailing status with respect to above pollutants close to the industrial zone. (author). 5 refs., 3 tabs., 2 figs

  6. In-situ degradation of sulphur mustard using (1R)-(-)-(camphorylsulphonyl) oxaziridine impregnated adsorbents

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, Abha, E-mail: abha_052002@yahoo.co.in [Industrial Toxicology Research Centre, Mahatam Gandhi Marg, Lucknow, UP (India); Saxena, Amit; Singh, Beer [Defence Research and Development Establishment, Jhansi Road, Gwalior, MP (India)

    2009-12-30

    Bis-2-chloroethyl sulphide (sulphur mustard or HD) is an extremely toxic and persistent chemical warfare agent. For in-situ degradation of HD and its analogues (simulants), i.e., dibutyl sulphide (DBS) and ethyl 2-hydroxyethyl sulphide (HEES), different adsorbents systems loaded with (1R)-(-)-(camphorylsulphonyl) oxaziridine were prepared. Solution of sulphur mustard and its simulants was prepared in carbon tetrachloride and taken for uniform adsorption on the impregnated systems using incipient volume. Degradation kinetics monitored by GC/FID were found to be first-order. The half-life of degradation reactions for simulants was obtained in less than 30 and for HD in 120 min. From the studied kinetics it was observed that reaction was very rapid with simulants and decreased rate was found for HD. The order of reactivity of MgO/Oxa system for HD and simulants was found to be DBS > HEES > HD. Reaction products of the oxidation reaction of simulants and HD on adsorbents were extracted in dichloromethane and analysed by GC-MS. The products were found to be non-toxic sulphoxide. The objective of the study is to develop a reactive adsorbent for in-situ degradation of sulphur mustard which could be used in nuclear biological and chemical (NBC) filtration systems.

  7. The effect of nitrogen and sulphur on the agronomical and water use ...

    African Journals Online (AJOL)

    The effect of nitrogen and sulphur on the agronomical and water use efficiencies of canola (Brassica napus L.) grown in selected localities of the Western Cape province, South Africa. Wonder Ngezimana, Gert A. Agenbag ...

  8. Studies on Corrosion of Annealed and Aged 18 Ni 250 Grade Maraging Steel in Sulphuric Acid Medium

    OpenAIRE

    Poornima, T.; Jagannatha, Nayak; Shetty, A. Nityananda

    2010-01-01

    The corrosion behavior of aged and annealed sample of 18 Ni 250 grade maraging steel was investigated in varied conditions of concentration and temperature of sulphuric acid medium, using electrochemical techniques like Tafel polarization and electrochemical impedance spectroscopy (EIS). The results obtained from both the techniques are in good agreement. These results have shown increase in corrosion rate of aged specimen with increase in concentration and temperature of sulphuric acid. With...

  9. Effects of sulphuric acid and hot water treatments on seed ...

    African Journals Online (AJOL)

    A study was carried out to investigate the effects of sulphuric acid and hot water treatments on the germination of Tamarind (Tamarindus indica L). Seeds were placed on moistened filter papers in 28 cm diameter Petri dishes under laboratory condition for germination. 330 seeds of T. indica (10 seeds per Petri dish) with ...

  10. Extraction of Zinc and Manganese from Alkaline and Zinc-Carbon Spent Batteries by Citric-Sulphuric Acid Solution

    Directory of Open Access Journals (Sweden)

    Francesco Ferella

    2010-01-01

    Full Text Available The paper is focused on the recovery of zinc and manganese from alkaline and zinc-carbon spent batteries. Metals are extracted by sulphuric acid leaching in the presence of citric acid as reducing agent. Leaching tests are carried out according to a 24 full factorial design, and empirical equations for Mn and Zn extraction yields are determined from experimental data as a function of pulp density, sulphuric acid concentration, temperature, and citric acid concentration. The highest values experimentally observed for extraction yields were 97% of manganese and 100% of zinc, under the following operating conditions: temperature 40∘C, pulp density 20%, sulphuric acid concentration 1.8 M, and citric acid 40 g L-1. A second series of leaching tests is also performed to derive other empirical models to predict zinc and manganese extraction. Precipitation tests, aimed both at investigating precipitation of zinc during leaching and at evaluating recovery options of zinc and manganese, show that a quantitative precipitation of zinc can be reached but a coprecipitation of nearly 30% of manganese also takes place. The achieved results allow to propose a battery recycling process based on a countercurrent reducing leaching by citric acid in sulphuric solution.

  11. Effects of elemental sulphur on heavy metal uptake by plants growing on municipal sewage sludge.

    Science.gov (United States)

    Dede, Gulgun; Ozdemir, Saim

    2016-01-15

    In this study experiment was carried out to determine the phytoextraction potential of six plant species (Conium maculatum, Brassica oleraceae var. oleraceae, Brassica juncea, Datura stramonium, Pelargonium hortorum and Conyza canadensis) grown in a sewage sludge medium amended with metal uptake promoters. The solubility of Cu, Cd and Pb was significantly increased with the application of elemental S due to decrease of pH. Faecal coliform number was markedly decreased by addition of elemental sulphur. The extraction of Cu, Cr and Pb from sewage sludge by using B. juncea plant was observed as 65%, 65% and 54% respectively that is statistically similar to EDTA as sulphur. The bioaccumulation factors were found higher (>1) in the plants tested for Cu and Pb like B. juncea. Translocation index (TI) calculated values for Cd and Pb were greater than one (>1) in both C. maculatum and B. oleraceae var. oleraceae. The results cleared that the amendment of sludge with elemental sulphur showed potential to solubilize heavy metals in phytoremediation as much as EDTA. Copyright © 2015 Elsevier Ltd. All rights reserved.

  12. Anion-exchange Studies of Radioactive Trace Elements in Sulphuric Acid Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Samsahl, K

    1963-01-15

    As part of a chemical group separation procedure used as a pretreatment in gamma spectrometric analysis, a study has been made of the adsorption from sulphuric acid solutions on strongly basic anion exchange resins, prepared in the hydroxide and the sulphate forms, of trace activities of Na, P, K, Ca, Sc, Cr, Mn, Fe, Co, Ni, Cu, Zn, Ga, Rb, Sr, Zr, Nb, Mo, Tc, Ag, Cd, In, Cs, Ba, La, Ce, Hf, Ta, W, Ir, Pa and Np. Besides adsorbing some of the trace elements in the solution, the anion exchange resin in the hydroxide form will neutralize the bulk of the sulphuric acid. This makes possible the subsequent sequential separation of chloride complexes on short anion-exchange columns by a stepwise increasing of the HCl concentration of the solution. On the basis of the results obtained in the present and earlier experiments, a new improved chemical group-separation procedure for mixtures of radioactive trace elements is outlined.

  13. Quantifying Sulphur Emissions and Atmospheric Aerosol Loading From the 1730-36 Lanzarote Eruption

    Science.gov (United States)

    Sharma, K.; Blake, S.; Self, S.

    2005-12-01

    The AD 1730-36 eruption of Lanzarote (Canary Islands) is the third largest basaltic fissure eruption known to have occurred in the last 1000 years, after the Icelandic events of Laki (AD 1783-84) and Eldgja (AD 934). Our new volume estimates suggest that the Lanzarote eruption produced ~6 km3 of alkali basalt magma along a 15-km long, E-W trending fissure. Eruptive activity occurred in five distinct phases. Each phase began with Strombolian fire fountain activity, building large spatter and scoria cones. This was accompanied and followed by effusive aa and pahoehoe lava flow emplacement. As studies in Iceland have shown, this type of sustained fissure eruption can release large amounts of SO2 to the upper atmosphere, leading to the formation of sulphate aerosol clouds and causing widespread environmental damage and human suffering. Matrix glasses in scoria and surface lava samples have 80-300 ppm S (EMPA) and 300-600 ppm H2O (FTIR), whereas glass inclusions in olivine have 420-2650 ppm S and 1000-5000 ppm H2O. Low sulphur inclusions are believed to be partially degassed, representing melt that was trapped during degassing-induced crystallization that occurred as a result of shallow decompression. The inclusions with the highest sulphur contents trap the original un-degassed melt, as indicated by their consistent S/K2O ratio (0.22). The high sulphur contents are also consistent with our finding, from olivine-spinel equilibria, that the magma was relatively oxidized (log fO2 -4.8) therefore favouring the formation of sulphate species and preventing sulphide saturation. Our glass analyses indicate that 40 Mt of SO2 was injected into the upper troposphere - lower stratosphere via 12-16-km-high eruption plumes and that over half this amount was released during the first year of activity. This figure correlates with published Greenland ice-core (GISP-2) data that shows an acidity spike in 1731, suggesting stratospheric transport of sulphate aerosol to the North during

  14. Energy and power alternatives

    International Nuclear Information System (INIS)

    Messerle, H.K.

    1992-01-01

    Taking into consideration the need for a safe energy supply, rising demand for energy worldwide and limited oil reserves, alternative energy resources for bulk power are discussed. They are nuclear fuel, fluidized bed combustion of coal, coal gasification with combined cycle process, coal-oil mixture combustion and MHD power generation process. It is pointed out that the major environmental impact of fossil fuels is in accumulation of greenhouse gases in the atmosphere and air pollution due to sulphur emission. (M.G.B.)

  15. Hydrogen production by high-temperature gas-cooled reactor. Conceptual design of advanced process heat exchangers of the HTTR-IS hydrogen production system

    International Nuclear Information System (INIS)

    Sakaba, Nariaki; Ohashi, Hirofumi; Sato, Hiroyuki; Hara, Teruo; Kato, Ryoma; Kunitomi, Kazuhiko

    2008-01-01

    Nuclear hydrogen production is necessary in an anticipated hydrogen society that demands a massive quantity of hydrogen without economic disadvantage. Japan Atomic Energy Agency (JAEA) has launched the conceptual design study of a hydrogen production system with a near-term plan to connect it to Japan's first high-temperature gas-cooled reactor HTTR. The candidate hydrogen production system is based on the thermochemical water-splitting iodine sulphur (IS) process.The heat of 10 MWth at approximately 900degC, which can be provided by the secondary helium from the intermediate heat exchanger of the HTTR, is the energy input to the hydrogen production system. In this paper, we describe the recent progresses made in the conceptual design of advanced process heat exchangers of the HTTR-IS hydrogen production system. A new concept of sulphuric acid decomposer is proposed. This involves the integration of three separate functions of sulphuric acid decomposer, sulphur trioxide decomposer, and process heat exchanger. A new mixer-settler type of Bunsen reactor is also designed. This integrates three separate functions of Bunsen reactor, phase separator, and pump. The new concepts are expected to result in improved economics through construction and operation cost reductions because the number of process equipment and complicated connections between the equipment has been substantially reduced. (author)

  16. Gas chromatographic sulphur speciation in heavy crude oil using a modified standard D5623 method and microfluidic Deans switching.

    Science.gov (United States)

    Heshka, Nicole E; Choy, Joanne M; Chen, Jinwen

    2017-12-29

    A modification to American Society for Testing and Materials (ASTM) method D5623 is proposed to enable successful and repeatable analysis of heavy crude oil samples. A two-dimensional gas chromatography configuration was implemented, with separation of sulphur compounds occurring on two columns. A Deans switch is used to enable heart-cutting of volatile sulphur compounds onto a DB-Sulfur stationary phase, and separation occurs concurrently with the backflushing of the primary column. The use of a sulphur-selective detector increases selectivity, and 22 volatile sulphur species are quantified in less than 15min, which is almost half the time of the original ASTM method. Samples ranging from light distillation cuts to whole crudes (boiling from 100°C to >750°C) were analyzed with minimal sample preparation. The calculated limit of detection was 0.7mg/kg, repeatability was 3% relative standard deviation (RSD), and a linear range of 1-250mg/kg was obtained, with an R 2 value of 0.994 or better, depending on the compound. Crown Copyright © 2017. Published by Elsevier B.V. All rights reserved.

  17. Sulphur isotopes as tracers of the influence of a coal-fired power plant on a Scots pine forest in Catalonia (NE Spain)

    Science.gov (United States)

    Puig, R.; Àvila, A.; Soler, A.

    Stable sulphur isotopes and major ionic composition were analysed in precipitation and throughfall samples from a Scots pine ( Pinus sylvestris, L.) forest near the Cercs coal-fired power plant (Catalonia, NE Spain). The purpose of the study was to determine the main sources of sulphur deposition on this pine forest. Sulphur isotope measurements from the SO 2 power plant stack emissions were used to identify the isotopic signature of this source. Net throughfall fluxes of sulphur (26.1 kg S ha 1 yr -1) and nitrogen (16.3 kg N ha -1 yr -1) were higher—5-25 times higher for S and 5-15 times for N—at this site than in other forests in Catalonia. Sulphur isotope analysis confirmed that the net throughfall fluxes of sulphur were mostly due to the dry deposition of the SO 2 power plant emissions onto the pine canopies. Two potential atmospheric end-members were distinguished: regional background rainwater (δ 34S=+7.2‰) and power plant emissions (δ 34S=-2.8‰). By applying a two-component sulphur isotope mixing model, we found that during periods of low power plant activity (⩽10 emission h day -1), 62% of the throughfall sulphate could be attributed to the power plant emissions. At higher activity periods (⩾14 emission h day -1), this contribution rose to 73%. Although power plant contribution to bulk deposition was lower in both cases (34% and 45%), the possible influence of sulphate coming with long-range transport events from the polluted areas in the Mediterranean basin (δ 34S≈0‰) was not discarded.

  18. Sulphur content of Red pine (Pinus brutia) needles and barkas indicator of atmospheric pollution in Southwest Turkey

    DEFF Research Database (Denmark)

    Gemici, M.; Gemici, Y.; Tan, Kit

    2006-01-01

    of SO2 emission. The highest increase was observed in two-year-old needles. We thus conclude that the sulphur content of two-year-old needles can be a bioindicator of some importance if the cause of tree death is known to be SO2. The sulphur content of bark samples was found to be lower in less polluted...

  19. Produtividade da soja no cerrado influenciada pelas fontes de enxofre Soybean grain yield in cerrado region influenced by sulphur sources

    Directory of Open Access Journals (Sweden)

    Dirceu Luiz Broch

    2011-09-01

    Full Text Available O enxofre é um componente de proteínas e aminoácidos em plantas, sendo exigido em boa quantidade por leguminosas, pelo alto acúmulo de proteínas nessas espécies. Com isso, este trabalho teve por objetivo verificar a influência de diferentes fontes de enxofre sobre a produtividade de grãos na cultura da soja. O experimento foi instalado na área experimental da Fundação MS, em Maracajú, MS, em três anos consecutivos no delineamento de blocos ao acaso, com quatro repetições, submetidas à análise de variância conjunta. Foram implantadas as cultivares BRS-133 (2002/03 e 2003/04 e CD 202 (2004/05. Como tratamento foram avaliados: as adições de enxofre na forma de superfosfato simples, MAP sulfurado + Sulfurgran, Sulfurgran, enxofre elementar, gesso granulado, Fosmag 509M6, gesso agrícola a lanço e testemunha, sem a aplicação. A soja responde à aplicação de enxofre em solos das regiões do cerrado brasileiro, sendo necessária, na maioria das vezes, a fertilização com este nutriente para obtenção de altas produtividades. A grande maioria das fontes de enxofre utilizadas foi eficiente em fornecer este nutriente para a soja, com destaque para a aplicação de MAP Sulfurado + Sulfurgran, Formag 509M6 e gesso agrícola a lanço, que promoveram as melhores produtividades de grãos. O enxofre elementar não foi eficiente em disponibilizar S para a cultura.Sulphur is a component of protein and aminoacids in plants, being required in an expressive amount by leguminous, as function of high protein levels in these plants. Then, this work aimed to verify the influence of different sulphur sources on soybean grain yield. The experiment was carried out at the experimental area of Fundação MS, Maracajú, MS, in three consecutive years in a randomized block design with four replications, submitted to variance analysis of group experiments. The cultivars used were BRS-133 (2002/03 and 2003/04 and CD 202 (2004/05. As treatments, it was

  20. Chemical transport of niobium(V) oxide and of lithium niobate with sulphur

    International Nuclear Information System (INIS)

    Schaefer, H.

    1988-01-01

    Niobium(V) oxide is transported by means of sulphur (calculated for 10 bar at 1223 K) from 1273 → 1173 K. The same applies for lithium niobate. Similar experiments of lithium oxide lead to turbidity of the quartz ampoule. (author)

  1. Liver metastases: Sulphur hexafluoride-enhanced ultrasonography for lesion detection: a systematic review

    NARCIS (Netherlands)

    Cabassa, Paolo; Bipat, Shandra; Longaretti, Laura; Morone, Mario; Maroldi, Roberto

    2010-01-01

    This is a systematic review to evaluate the accuracy of contrast-enhanced ultrasonography (CEUS) performed with "SonoVue" (sulphur hexafluoride) in the detection of hepatic metastases. The MEDLINE, EMBASE and COCHRANE Databases were searched, regardless of language, for relevant articles published

  2. Green approach to corrosion inhibition of mild steel in hydrochloric acid and sulphuric acid solutions by the extract of Murraya koenigii leaves

    Energy Technology Data Exchange (ETDEWEB)

    Quraishi, M.A., E-mail: maquraishi@rediffmail.com [Department of Applied Chemistry, Institute of Technology, Banaras Hindu University, Varanasi 221005 (India); Singh, Ambrish; Singh, Vinod Kumar [Udai Pratap Autonomous College, Varanasi 221002 (India); Yadav, Dileep Kumar; Singh, Ashish Kumar [Department of Applied Chemistry, Institute of Technology, Banaras Hindu University, Varanasi 221005 (India)

    2010-07-01

    The inhibition of the corrosion of mild steel in hydrochloric acid and sulphuric acid solutions by the extract of Murraya koenigii leaves has been studied using weight loss, electrochemical impedance spectroscopy (EIS), linear polarization and potentiodynamic polarization techniques. Inhibition was found to increase with increasing concentration of the leaves extract. The effect of temperature, immersion time and acid concentration on the corrosion behavior of mild steel in 1 M HCl and 0.5 M H{sub 2}SO{sub 4} with addition of extract was also studied. The inhibition was assumed to occur via adsorption of the inhibitor molecules on the metal surface. The adsorption of the extract on the mild steel surface obeys the Langmuir adsorption isotherm. The activation energy as well as other thermodynamic parameters (Q, {Delta}H*, and {Delta}S*) for the inhibition process was calculated. These thermodynamic parameters show strong interaction between inhibitor and mild steel surface. The results obtained show that the extract of the leaves of M. koenigii could serve as an effective inhibitor of the corrosion of mild steel in hydrochloric and sulphuric acid media.

  3. Environmental effects of energy forest (short rotation willow)

    International Nuclear Information System (INIS)

    Frank, K.

    1994-01-01

    This paper deals with environmental effects of producing and combusting energy forest fuel. Energy forest means short rotation willow (Salix). Supposed effects of sewage sludge application are discussed as well. Energy forestry on agricultural land implies both advantages and disadvantages for the environment. Leaf litter (humified leaves) increases the humus content in the top soil. The soil fauna is also positively affected. Until now performed studies about nitrogen leakage from fields cultivated with energy forest (Salix), have not given any distinct results. A retarded drainage within energy forest fields is on the other hand noticed. While the root system of Salix is active during a long period of the year, the nitrogen leakage become less compared to traditional cultivation. The content of plant nutrients and organic matter in sewage sludge make a resource that can be useful for agricultural purposes, especially for energy forest cultivation. The content of heavy metals and organic emissions contradicts sludge application to agricultural land. Sewage sludge with todays quality increases somewhat the content of heavy metals in the soil. This condition can be counteracted to a certain extent by growing energy forest. It has been established that Salix has high ability to heavy metal uptake, especially cadmium. Growing energy forest on drained farm land is connected with a risk for root penetration into the drainage system. With enough water and plant nutrients in the top soil the risk is reduced. Shallow depth of the pipes increases the risk. Combustion of wood chip from energy forests (and other types of biomass) gives especially two advantages. It does not give any net contribution of carbon dioxide to the atmosphere. The sulphur discharge will be minimal since the sulphur content in wood fuels is low. Discharge of nitrogen oxide and hydrocarbons may give some problems. These can be reduced by technological measures when combusting. 27 refs, 4 tabs

  4. Yeast strains role on the sulphur dioxyde combinations of wines obtained from noble rot and raisining grapes

    Directory of Open Access Journals (Sweden)

    Isabelle Masneuf-Pomarède

    2000-03-01

    Full Text Available The influence of four industrial and indigenous yeast strains on the sulphur dioxide combinations of wines obtained from noble rot and raisining grapes is studied in different growth of the Sauternes area and one growth in the Jurançon area. The analysis of ketonic compounds (pyruvic acid and 2-oxo-glutaric acid, acetaldehyde and PC50 on the wines clearly showed significant statistical difference between the yeast strains for the sulphur dioxide combination. By adding the same dosage of sulphiting, the free SO2 levels are variable depending on the yeast strain used. One strain (Zymaflore ST, isolated from a spontaneous fermentation of a botrytised must, giving wines with low PC50 values, is well adapted for the noble rot must vinification. The choice of the yeast strain is a parameter of importance to limit the sulphur dioxide amount in the wines.

  5. Electrochemical Determination of Low Molecular Mass Thiols Content in Potatoes (Solanum tuberosum Cultivated in the Presence of Various Sulphur Forms and Infected by Late Blight (Phytophora infestans

    Directory of Open Access Journals (Sweden)

    Rene Kizek

    2008-05-01

    Full Text Available In the present paper potato plants were cultivated in the presence of ammonium sulphate or elemental sulphur supplementation into the soil to reveal the effects of different sulphur forms on content of nitrogen, phosphorus, potassium, calcium, magnesium and sulphur, and yield of tubers. During the investigation of the influence of different sulphur forms on yield of potato tubers we did not observe significant changes. Average weight of tubers of control plants per one experimental pot was 355 g. Application of sulphur in both forms resulted in moderate potato tubers weight reduction per one experimental pot compared to control group; average value ranged from 320 to 350 g per one experimental pot. Further we treated the plants with two different supplementation of sulphur with cadmium(II ions (4 mg of cadmium(II acetate per kilogram of the soil. The significantly lowest cadmium content (p < 0.05 was determined in tissues of plants treated with the highest dosage of elemental sulphur (0.64 mg Cd/kg compared to control plants (0.82 mg Cd/kg. We also aimed our attention on the cadmium content in proteins, lipids or soluble carbohydrates and ash. Application of sulphate as well as elemental sulphur resulted in significant cadmium content reduction in lipid fraction compared to control plants. In addition to this we quantified content of low molecular mass thiols in potatoes tissues. To determine the thiols content we employed differential pulse voltammetry Brdicka reaction. After twelve days of the treatment enhancing of thiols level was observed in all experimental groups regardless to applied sulphur form and its concentration. Finally we evaluated the effect of sulphur supplementation on Phytophora infestans infection of potato plants.

  6. Silica Sulphuric Acid as an Efficient Catalyst for the Catalytic and ...

    African Journals Online (AJOL)

    NJD

    presence of a catalytic amount of silica sulphuric acid under micellar media in moderate to good yields. KEYWORDS. Sodium ... Production of aromatic nitro compounds is an important industrial process and involves the unsolved problems of ... V7 and Re9) and titanium and chromium silicates.10 Some of the procedures ...

  7. New perspectives for the petroleum industry. Bioprocesses for the selective removal of sulphur, nitrogen and metals

    International Nuclear Information System (INIS)

    Zerlia, T.

    2000-01-01

    Fuel biocatalytic conversion is a process that removes, through selective enzyme-catalyzed reactions, sulphur, nitrogen and metals. The mild operating conditions, the specificity of reactions and the quality of coproducts (particularly the organo sulphur compounds, a source for the petrochemical industry) are just a few of the attractive aspects of this new technology which could open a new world of possibilities in the technology and in the environmental impact of fuels. The paper shows the state-of-the-art of the research and applications of bioprocesses to the petroleum field [it

  8. Levels of cystathionine gamma lyase production by Geotrichum candidum in synthetic media and correlation with the presence of sulphur flavours in cheese.

    Science.gov (United States)

    Gente, Stéphanie; La Carbona, Stéphanie; Guéguen, Micheline

    2007-03-10

    Geotrichum candidum is a cheese-ripening agent with the potential to produce sulphur flavour compounds in soft cheeses. We aimed to develop an alternative test for predicting the aromatic (sulphur flavours) potential of G. candidum strains in soft cheese. Twelve strains of G. candidum with different levels of demethiolase activity (determined by a chemical method) in YEL-met (yeast extract, lactate methionine) medium were studied. We investigated cgl (cystathionine gamma lyase) gene expression after culture in three media - YEL-met, casamino acid and curd media - and then carried out sensory analysis on a Camembert cheese matrix. We found no correlation between demethiolase activity in vitro and cgl gene expression. Sensory analysis (detection of sulphur flavours) identified different aromatic profiles linked to cgl expression, but not to demethiolase activity. The RT-PCR technique described here is potentially useful for predicting the tendency of a given strain of G. candidum to develop sulphur flavours in cheese matrix. This is the first demonstration that an in vitro molecular approach could be used as a predictive test for evaluating the potential of G. candidum strains to generate sulphur compounds in situ (Camembert cheese matrix).

  9. Wet precipitators for sulphuric acid plants

    International Nuclear Information System (INIS)

    Ojanpera, R.O.

    1989-01-01

    Both the service requirements and design construction details have changed considerably in recent years for wet electrostatic precipitators as used for gas cleaning ahead of metallurgical sulphuric acid plants. Increased concern over acid quality has resulted in more emphasis on dust efficiencies compared to collection of acid mist. Also, higher static operating pressures have caused large structural loads on casing and internal components. In this paper these two issues are addressed in the following ways: Recognition that all dusts do not collect similarly. The mechanism by which various dusts collect affect the design of the entire wet gas cleaning system. Use of both traditional and newer materials of construction to accommodate the higher design pressures while still maintaining corrosion resistance

  10. Biotic conversion of sulphate to sulphide and abiotic conversion of sulphide to sulphur in a microbial fuel cell using cobalt oxide octahedrons as cathode catalyst.

    Science.gov (United States)

    Chatterjee, Pritha; Ghangrekar, M M; Rao, Surampalli; Kumar, Senthil

    2017-05-01

    Varying chemical oxygen demand (COD) and sulphate concentrations in substrate were used to determine reaction kinetics and mass balance of organic matter and sulphate transformation in a microbial fuel cell (MFC). MFC with anodic chamber volume of 1 L, fed with wastewater having COD of 500 mg/L and sulphate of 200 mg/L, could harvest power of 54.4 mW/m 2 , at a Coulombic efficiency of 14%, with respective COD and sulphate removals of 90 and 95%. Sulphide concentration, even up to 1500 mg/L, did not inhibit anodic biochemical reactions, due to instantaneous abiotic oxidation to sulphur, at high inlet sulphate. Experiments on abiotic oxidation of sulphide to sulphur revealed maximum oxidation taking place at an anodic potential of -200 mV. More than 99% sulphate removal could be achieved in a MFC with inlet COD/sulphate of 0.75, giving around 1.33 kg/m 3  day COD removal. Bioelectrochemical conversion of sulphate facilitating sulphur recovery in a MFC makes it an interesting pollution abatement technique.

  11. An elevation-based regional model for interpolating sulphur and nitrogen deposition

    Czech Academy of Sciences Publication Activity Database

    Kopáček, Jiří; Posch, M.; Hejzlar, Josef; Oulehle, F.; Volková, Alena

    2012-01-01

    Roč. 50, April (2012), s. 287-296 ISSN 1352-2310 R&D Projects: GA ČR(CZ) GA526/09/0567 EU Projects: European Commission(XE) 244121 - REFRESH Institutional support: RVO:60077344 Keywords : atmospheric deposition * sulphur * nitrogen * Vltava river Subject RIV: DI - Air Pollution ; Quality Impact factor: 3.110, year: 2012

  12. Thermal energy distribution analysis for hydrogen production in RGTT200K conceptual design

    International Nuclear Information System (INIS)

    Tumpal Pandiangan; Ign Djoko Irianto

    2011-01-01

    RGTT200K is a high temperature gas-cooled reactor (HTGR) which conceptually designed for power generation, hydrogen production and desalination. Hydrogen production process in this design uses thermochemical method of Iodine-Sulphur. To increase the thermal conversion efficiency in hydrogen production installations, it needs to design a thermal energy distribution and temperature associated with the process of thermo-chemical processes in the method of Iodine-Sulphur. In this method there are 7 kinds of processes: (i) H 2 SO4 decomposition reaction (ii) treatment of vaporization (iii) treatment of pre vaporizer (iv) treatment of flash 4 (v) treatment of decomposition of HI (vi) treatment of the flash 1-3 and (vii) Bunsen reaction. To regulate the distribution of energy and temperature appropriate to the needs of each process used 3 pieces of heat exchanger (HE). Calculation of energy distribution through the distribution of helium gas flow has been done with Scilab application programs, so that can know the distribution of thermal energy for production of 1 mole of hydrogen. From this model, it can calculate the thermal energy requirement for production of hydrogen at the desired capacity. In the conceptual design of RGTT200K, helium discharge has been designed by 20 kg/s, so that an efficient hydrogen production capacity needed to produce 15347.8 for 21.74 mole of H 2 . (author)

  13. Determination of chloride and sulphur in sodium by ion chromatography and its application to PFBR sodium samples

    International Nuclear Information System (INIS)

    Vijayalakshmi, S.; Ushalakshmi, K.

    2011-01-01

    Analytical method using ion chromatography was developed for the determination of chloride and sulphur in sodium. In this method, sodium was dissolved in water and various sulphur species present in the sample was oxidized to sulphate using hydrogen peroxide. Carbon dioxide gas was passed through the solution to convert sodium hydroxide to carbonate solution. The resulting sample solution was analysed using suppressed Ion chromatography employing carbonate eluent. This method was applied to the analysis of sodium samples procured for prototype fast breeder reactor. (author)

  14. Analysis of the reactivity of sulphur compounds in petroleum cuts: kinetics and modelling of hydro-treating; Analyse de la reactivite des composes soufres dans les coupes petrolieres: cinetique et modelisation de l'hydrotraitement

    Energy Technology Data Exchange (ETDEWEB)

    Lopez Garcia, C

    2000-12-01

    The study of the hydro-treating of middle distillates comprised the following steps: - Identification and reactivity study of the sulphur compounds present in these petroleum cuts; - Modelling of the process by a chemical kinetic approach. The hydro-treating of middle distillates is a refining process that allows elimination of organic compounds containing sulphur, nitrogen, oxygen and metals. The process also hydrogenates the aromatic compounds providing improved cetane index gas-oils while respecting the regulations that severely limit the content of sulphur compounds. The extension and the improvement of a kinetic model for the hydro-treating of LCO gas-oils (light cycle oil gas-oils) are presented in this work. In order to improve the hydro-desulfurization model predictions, a detailed identification of the sulphur compounds contained in LCO gas-oils was carried out using gas chromatography with a sulphur chemiluminescence detector (GC-SCD). The most refractory sulphur compounds (alkyl-di-benzothiophenes) were identified and lumped into different families. Based on a lumped reaction scheme with a Langmuir-Hinshelwood representation, the model takes into account the influence of temperature, total pressure and hydrogen sulphide partial pressure on the reaction rates for hydro-desulfurization, hydro-denitrogenation and hydro-de-aromatization. The model parameter estimation was based on experiments that were carried out on a micro-pilot unit using an industrial sulfided NiMo/Al{sub 2}O{sub 3} catalyst and LCO feedstocks. The analytical study of the sulphur compounds was also extended to the case of straight run gas-oils (SR). For these feedstocks, a method using high-resolution mass spectrometry coupled with gas chromatography (GC-HRMS) was developed. In this way, the kinetic model can now be extended for the SR gas-oil hydro-treating or for LCO-SR mixtures. (author)

  15. Unravelling the sulphur isotope systematics of an alkaline magmatic province: implications for REE mineralization and exploration

    Science.gov (United States)

    Hutchison, W.; Finch, A.; Boyce, A.; Friis, H.; Borst, A. M.; Horsburgh, N. J.

    2017-12-01

    Some of the world's best alkaline rare earth element (REE) deposits are formed in magmatic systems that are sealed (i.e., those that are autometasomatised and maintain reducing conditions). Conversely, in open systems where oxidizing fluids infiltrate, it is commonly assumed that REE are redistributed over a wider (less concentrated) zone. Sulphur isotope fractionation is sensitive to variations in temperature and redox, and, although sulphide minerals are relatively abundant in alkaline systems, there have been few attempts to test these hypotheses and develop a sulphur isotope proxy for alkaline metasomatism and formation of associated REE deposits. The Gardar Rift Province in southern Greenland was volcanically active in two periods between 1300 and 1100 Ma and is an ideal natural laboratory to explore sulphur isotope systematics because a near-complete alkaline magmatic lineage is exposed. We present new δ34S from across the province with a particular focus on three alkaline systems (Ilímaussaq, Motzfeldt and Ivigtût) that also host major REE deposits. Primitive mafic rocks from regional Gardar dykes and lavas have a restricted range of δ34S between 0 and 3 ‰ and fractional crystallization imparts no observable change in δ34S. In a few cases high-δ34S rocks (>15 ‰) occur when intrusive units have assimilated local sedimentary crust (δ34S = 25 ‰). Most δ34S variation takes place in the roof zones of alkaline intrusions during late-magmatic and hydrothermal stages, and we identify clear differences between the complexes. At Ilímaussaq, where the magmatic series is exceptionally reduced (below QFM buffer), roof zone δ34S remains narrow (0-3 ‰). At Motzfeldt, a more open oxidizing roof zone (MH buffer), δ34S ranges from -12 ‰ in late-stage fluorite veins to +12 ‰ where local crust has been assimilated. Ivigtût is intermediate between these end-members varying between -5 to +5 ‰. The δ34S variations primarily relate to temperature and

  16. Zinc chelates as new activators for sulphur vulcanization of acrylonitrile-butadiene elastomer

    Directory of Open Access Journals (Sweden)

    2009-04-01

    Full Text Available The goal of this work was to apply several zinc chelates as activators for sulphur vulcanization of acrylonitrilebutadiene elastomer (NBR, in order to find alternatives for the conventionally used zinc oxide. In this article, we discuss the effects of different zinc complexes on the cure characteristics, crosslinks distribution in the elastomer network and mechanical properties of acrylonitrile-butadiene rubber. Zinc chelates seem to be good substitutes for zinc oxide as activators for sulphur vulcanization of NBR rubber, without detrimental effects on the crosslinking process and physical properties of the obtained vulcanizates. Moreover, application of zinc complexes allows to reduce the amount of zinc ions in rubber compounds by 40% compared to conventionally crosslinked vulcanizates with zinc oxide. It is a very important ecological goal since zinc oxide is classified as toxic to aquatic species and its amount in rubber products must be reduced below 2.5% at least. From a technological point of view it is a very important challenge.

  17. Determination of sulphur-35 impurity in solutions of phosphorus-32

    International Nuclear Information System (INIS)

    Rodriguez Pasques, R.H.; Iglicki, F.A; Cittadini, P.E.

    1982-01-01

    A method has been developed in order to evaluate the activity of sulphur-35 impurity in solutions of phosphorus-32. The procedure is based on the precipitation on benzidine sulphate in acid solution and further purification by dissolving and reprecipitating under appropriate conditions. 35 S beta radiation is measured with and end-window gas counter. A correction for any remaining 32 P is determined by differential absorption through aluminum. (author) [es

  18. Predicting sulphur and nitrogen deposition using a simple statistical method

    Czech Academy of Sciences Publication Activity Database

    Oulehle, F.; Kopáček, Jiří; Chuman, T.; Černohous, V.; Hůnová, I.; Hruška, Jakub; Krám, Pavel; Lachmaová, Z.; Navrátil, Tomáš; Štěpánek, Petr; Tesař, Miroslav; Christopher, Evans D.

    2016-01-01

    Roč. 140, sep (2016), s. 456-468 ISSN 1352-2310 Grant - others:EHP(CZ) EHP-CZ02-OV-1-014-2014 Program:CZ02 Institutional support: RVO:67179843 ; RVO:60077344 ; RVO:67985831 ; RVO:67985874 Keywords : precipitation * sulphur * nitrogen * deposition * monitoring * upscaling Subject RIV: EH - Ecology, Behaviour; DD - Geochemistry (GLU-S); DI - Air Pollution ; Quality (BC-A); BK - Fluid Dynamics (UH-J) Impact factor: 3.629, year: 2016

  19. Why high energy physics

    International Nuclear Information System (INIS)

    Diddens, A.N.; Van de Walle, R.T.

    1981-01-01

    An argument is presented for high energy physics from the point of view of the practitioners. Three different angles are presented: The cultural consequence and scientific significance of practising high energy physics, the potential application of the results and the discovery of high energy physics, and the technical spin-offs from the techniques and methods used in high energy physics. (C.F.)

  20. Analysis of the reactivity of sulphur compounds in petroleum cuts: kinetics and modelling of hydro-treating; Analyse de la reactivite des composes soufres dans les coupes petrolieres: cinetique et modelisation de l'hydrotraitement

    Energy Technology Data Exchange (ETDEWEB)

    Lopez Garcia, C.

    2000-12-01

    The study of the hydro-treating of middle distillates comprised the following steps: - Identification and reactivity study of the sulphur compounds present in these petroleum cuts; - Modelling of the process by a chemical kinetic approach. The hydro-treating of middle distillates is a refining process that allows elimination of organic compounds containing sulphur, nitrogen, oxygen and metals. The process also hydrogenates the aromatic compounds providing improved cetane index gas-oils while respecting the regulations that severely limit the content of sulphur compounds. The extension and the improvement of a kinetic model for the hydro-treating of LCO gas-oils (light cycle oil gas-oils) are presented in this work. In order to improve the hydro-desulfurization model predictions, a detailed identification of the sulphur compounds contained in LCO gas-oils was carried out using gas chromatography with a sulphur chemiluminescence detector (GC-SCD). The most refractory sulphur compounds (alkyl-di-benzothiophenes) were identified and lumped into different families. Based on a lumped reaction scheme with a Langmuir-Hinshelwood representation, the model takes into account the influence of temperature, total pressure and hydrogen sulphide partial pressure on the reaction rates for hydro-desulfurization, hydro-denitrogenation and hydro-de-aromatization. The model parameter estimation was based on experiments that were carried out on a micro-pilot unit using an industrial sulfided NiMo/Al{sub 2}O{sub 3} catalyst and LCO feedstocks. The analytical study of the sulphur compounds was also extended to the case of straight run gas-oils (SR). For these feedstocks, a method using high-resolution mass spectrometry coupled with gas chromatography (GC-HRMS) was developed. In this way, the kinetic model can now be extended for the SR gas-oil hydro-treating or for LCO-SR mixtures. (author)

  1. INVESTIGATION OF DISSOLVED SULPHATE IN VARIOUS GEOTHERMAL FIELDS OF SUMATRA USING OXYGEN AND SULPHUR ISOTOPES

    Directory of Open Access Journals (Sweden)

    E. Ristin Pujiindiyati

    2010-06-01

    Full Text Available There are at least 30 high temperature systems; eleven active volcanoes, five degassing volcanoes and one caldera volcano controlled by Sumatra Fault Zone over a length of 1700 km. To understand this geothermal field system, some information about geochemistry including isotope composition in its fluid is needed. Sulphur-34 and oxygen-18 isotopes in dissolved sulphate pair have been used to determine the origin of acidic fluid of sulphate and to evaluate the process involved. The fluids from eight hot springs, two fumaroles, four deep wells and crater have been collected in along Sumatra geothermal fields. Sulphur-34 (d 34S (SO4, 0/00 CDT and oxygen-18 (d 18O (SO4, 0/00 SMOW in sulphate is analyzed according to Robinson-Kusakabe and Rafter method, respectively. The d 34S (SO4 values from Sibayak wells are more enriched of 16.8 0/00 to 18.2 0/0 that may indicate the dissolution of anhydrite minerals or isotope partitioning in hydration of SO2. The d 34S (SO4 values from two fumaroles (Pusuk Bukit - North Sumatra and Rantau Dadap - South Sumatra are at depleted value of -0.150/00 and 1.80/00, those are close to d 34S from magmatic sulphur.  In general, the d 34S (SO4 of springs spread in a wide range of 5.250/00 to14.20/00 and show a mixing process between atmospheric sulphate and sulphate from deep wells. The d 18O (SO4 from wells exhibits depleted value around -3.60/00 suggesting that 87.5% of sulphate oxygen is derived from groundwater oxygen and 12.5% is derived from atmospheric molecular oxygen in sulphide oxidation reaction. In the other hand, hot springs (except Semurup, crater and fumaroles have enriched value of d 18O (SO4. These enriched values suggest that a higher percentage of atmospherically derived oxygen compared to those from the depth.   Keywords: isotope, geothermal, Sumatra

  2. Analyses on the formation of atmospheric particles and stabilized sulphuric acid clusters

    Energy Technology Data Exchange (ETDEWEB)

    Paasonen, P.

    2012-11-01

    Aerosol particles have various effects on our life. They affect the visibility and have diverse health effects, but are also applied in various applications, from drug inhalators to pesticides. Additionally, aerosol particles have manifold effects on the Earths' radiation budget and thus on the climate. The strength of the aerosol climate effect is one of the factors causing major uncertainties in the global climate models predicting the future climate change. Aerosol particles are emitted to atmosphere from various anthropogenic and biogenic sources, but they are also formed from precursor vapours in many parts of the world in a process called atmospheric new particle formation (NPF). The uncertainties in aerosol climate effect are partly due to the current lack of knowledge of the mechanisms governing the atmospheric NPF. It is known that gas phase sulphuric acid most certainly plays an important role in atmospheric NPF. However, also other vapours are needed in NPF, but the exact roles or even identities of these vapours are currently not exactly known. In this thesis I present some of the recent advancements in understanding of the atmospheric NPF in terms of the roles of the participating vapours and the meteorological conditions. Since direct measurements of new particle formation rate in the initial size scale of the formed particles (below 2 nm) are so far infrequent in both spatial and temporal scales, indirect methods are needed. The work presented on the following pages approaches the NPF from two directions: by analysing the observed formation rates of particles after they have grown to sizes measurable with widely applied instruments (2 nm or larger), and by measuring and modelling the initial sulphuric acid cluster formation. The obtained results can be summarized as follows. (1) The observed atmospheric new particle formation rates are typically connected with sulphuric acid concentration to the power close to two. (2) Also other compounds, most

  3. Maximum permissible continuous release rates of phosphorus-32 and sulphur-35 to atmosphere in a milk producing area

    Energy Technology Data Exchange (ETDEWEB)

    Bryant, P M

    1963-01-01

    A method is given for calculating, for design purposes, the maximum permissible continuous release rates of phosphorus-32 and sulphur-35 to atmosphere with respect to milk contamination. In the absence of authoritative advice from the Medical Research Council, provisional working levels for the concentration of phosphorus-32 and sulphur-35 in milk are derived, and details are given of the agricultural assumptions involved in the calculation of the relationship between the amount of the nuclide deposited on grassland and that to be found in milk. The agricultural and meteorological conditions assumed are applicable as an annual average to England and Wales. The results (in mc/day) for phosphorus-32 and sulphur-35 for a number of stack heights and distances are shown graphically; typical values, quoted in a table, include 20 mc/day of phosphorus-32 and 30 mc/day of sulfur-35 as the maximum permissible continuous release rates with respect to ground level releases at a distance of 200 metres from pastureland.

  4. Air quality in the Kootenays: fine particulate (PM10) airborne metals and sulphur dioxide levels, 1993-1999

    International Nuclear Information System (INIS)

    2000-09-01

    Air quality monitoring data collected in the Kootenays over a seven year period from 1993 to 1999 are summarized in an effort to inform the public about air quality in the Kootenays and to assist them in understanding air quality monitoring results. Data includes hourly (TEOM) and weekly (NAPS) data for particulate matter (PM 1 0) airborne metals (arsenic, cadmium, lead and zinc) and sulphur dioxide. Analysis of monitoring data showed that particulate matter levels remained constant in most communities, with Johnson Lake and Slocan reporting the lowest levels, while Golden had the highest values during this period. Trail-Butler Park showed a clear declining trend in PM 1 0. Airborne metals and sulphur dioxide levels have decreased in the Kootenays during the seven year period, with only occasional exceedances of both Level A and B air quality objectives in some communities. The report includes a detailed description of the sampling methodology and the analyzed results for PM 1 0, airborne metals and sulphur dioxide for 10 communities in the region. 6 refs., 1 tab., 16 figs., 1 map

  5. A new biological method for preparing certain sulphurated substances labelled with S35

    International Nuclear Information System (INIS)

    Chapeville, F.; Maier-Huser, H.; Fromageot, P.

    1962-01-01

    Previous investigations have shown that the yolk-sac of embryonic bird's eggs can be used to produce the following reactions: (a) reduction of sulphate to sulphite; (b) fixation of the sulphite on the carbon chain produced by the desulf-hydration of l-cysteine, with formation of l-cysteic acid; (c) decarboxylation of the l-cysteine acid into taurine. The enzymatic system which causes reaction (b) has been purified. It also acts as a catalyst in the sulphur-exchange between the cysteine and the mineral sulphide. The authors have utilized these data in preparing sulphurated substances labelled with S 35 : taurine S 35 , l-cysteine S 35 and l-cysteic acid S 35 . For each of the three, they discuss the chemical reactions involved, the methods of preparation, the experimental conditions of extraction and purity-control, together with the yields and specific activities obtained. (authors) [fr

  6. Tightening rules of the oil game; Industry preparing for sulphur-free products

    International Nuclear Information System (INIS)

    Ropponen, V.M.

    2002-01-01

    Increasing demand for sulphur-free fuels is the major driving force behind Fortum's oil refining investments. Environmental regulations are also setting the direction for oil retail network investments and will lead to closure of some retail sites. The year 2001 was marked by fluctuations in crude oil prices and low refining margins

  7. Effect of Nitric and Oxalic Acid Addition on Hard Anodizing of AlCu4Mg1 in Sulphuric Acid

    Directory of Open Access Journals (Sweden)

    Maximilian Sieber

    2018-02-01

    Full Text Available The anodic oxidation process is an established means for the improvement of the wear and corrosion resistance of high-strength aluminum alloys. For high-strength aluminum-copper alloys of the 2000 series, both the current efficiency of the anodic oxidation process and the hardness of the oxide coatings are significantly reduced in comparison to unalloyed substrates. With regard to this challenge, recent investigations have indicated a beneficial effect of nitric acid addition to the commonly used sulphuric acid electrolytes both in terms of coating properties and process efficiency. The present work investigates the anodic oxidation of the AlCu4Mg1 alloy in a sulphuric acid electrolyte with additions of nitric acid as well as oxalic acid as a reference in a full-factorial design of experiments (DOE. The effect of the electrolyte composition on process efficiency, coating thickness and hardness is established by using response functions. A mechanism for the participation of the nitric acid additive during the oxide formation is proposed. The statistical significance of the results is assessed by an analysis of variance (ANOVA. Eventually, scratch testing is applied in order to evaluate the failure mechanisms and the abrasion resistance of the obtained conversion coatings.

  8. High Pressure Oxydesulphurisation of Coal—Effect of Oxidizing Agent, Solvent, Shear and Agitator Configuration

    Directory of Open Access Journals (Sweden)

    Moinuddin Ghauri

    2016-06-01

    Full Text Available The ambient temperature high pressure oxydesulphurisation technique was investigated to reduce the sulphur content. Prince of Wales coal was chosen for this study. The focus of the study was to investigate the reduction of both pyritic and organic sulphur while changing the KMnO4/Coal ratio, agitation speed, agitator configuration, and shear. The effect of different concentrations of acetone as a solvent and effect of particle size on the sulphur removal was also studied by a series of experimental runs at ambient temperature. Heating value recovery was found to be increased with the decreased KMnO4/Coal ratio and with decreased acetone concentration. It was found that sulphur removal was enhanced with the increase in shear using a turbine impeller. The effect of particle size was more significant on the pyritic sulphur removal as compared to the organic sulphur removal while heating value recovery was found to increase with decreased desulphurization tome for both, under atmospheric and high pressure.

  9. Sulphur dissociation in nuclear emulsion at 3.7 and 200A GeV

    Energy Technology Data Exchange (ETDEWEB)

    El-Nadi, M.; Abdelsalam, A.; Shaat, E.A.; Abou Moussa, Z. [Physics Department, Faculty of Science, Cairo University, Giza (Egypt); Hussien, A. [Physics Department, Faculty of Science, Cairo University, Fayoum Branch, Fayoum (Egypt); Ali-Mossa, N. [Basic Science Department, Faculty of Engineering, Banha Branch, Zagazig University, Banha (Egypt); Kamel, S.; Hafiz, M.E. [Physics Department, Faculty of Education, Ain Shams University, Cairo (Egypt); Abdel-Waged, K.H. [Physics Department, Faculty of Science, Zagazig University, Banha (Egypt)

    2002-02-01

    In this work, the electromagnetic dissociation (EMD) of sulphur projectile induced by two widely differing energies in nuclear emulsions is investigated. Although the percentages of EMD events of the total numbers of studied interactions are relatively small, i.e. 5.7 and 14.4% for 3.7 and 200A GeV interactions respectively, one could extract some results out of them. The emission of a proton through the {sup 32}S({gamma}, p){sup 31}P channel is found to be a dominant process (43.8%) at 200A GeV whereas the single alpha emission through the {sup 32}S({gamma}, {alpha}){sup 28}Si channel is the dominant one (34.0%) at 3.7A GeV. Multiplicity distributions of hydrogen and helium isotopes as well as the measured probabilities for the different modes of fragmentation are studied. The comparison of the present results, from electromagnetic and peripheral nuclear interactions, indicates the effective role of the different reaction mechanisms at ultra-relativistic energy (200A GeV). The experimental inclusive cross sections of different fragmentation modes produced in the EMD of {sup 32}S ions at 200A GeV were found to be in satisfactory agreement with the predictions of the combined approach of Pshenichnov et al. (author)

  10. Fertilizer nitrogen recovery by onion (Allium cepa) as influenced by N and S application in a sulphur deficient soil

    International Nuclear Information System (INIS)

    Sachdev, M.S.; Sachdev, P.; Mittal, R.B.; Luthra, V.K.

    1991-01-01

    A field experiment was conducted in a sulphur deficient sandy loam soil to evaluate the fertilizer N-utilization by onion (Allium cepa) using 15 N-labelled urea. The fresh bulb yield of onion significantly increased with the application of both nitrogen and sulphur. The recovery of fertilizer N by onion was 23.4 to 34.4 per cent at 60 kg N/ha and between 17.5 and 19.3 per cent at 120 kg/ha level. Application of nitrogen with sulphur at 20 kg S/ha through gypsum resulted in significant increase in per cent utilization of urea nitrogen. Nearly 57 to 68 per cent of the residual fertilizer N could be traced in soil after the harvest of onion crop, whereas, 9 to 14 per cent of the applied fertilizer N could not be accounted for. (author). 8 refs., 3 tabs., 2 figs

  11. Migration of methyl and phenyl radicals, oxygen and sulphur atoms in certain diphenylthiophosphorane derivatives under electron impact

    International Nuclear Information System (INIS)

    Cauquis, G.; Divisia, B.; Ulrich, J.

    The fragmentation of various diphenylthiophosphoranes (Ph 2 P(S)R) subjected to electron impact gives rise to rearrangements dependent on the nature of the radical R. Migrations of phenyl or methyl radicals from phosphorus towards sulphur were thus observed for R=Ph, CH 3 , CH 2 Ph and NH 2 . When an electrophilic centre is formed, during a fragmentation, on a carbon in the α-position of the diphenylthiophosphoranyl radical, migrations of sulphur atoms and phenyl radicals take place from the phosphorus towards the carbon. This is found to be the case with certain fragmentations of diazo 5 and 6 compounds [fr

  12. SULPHUR-CONTAINING AMINO ACIDS METABOLISM IN EXPERIMENTAL HYPER- AND HYPOTHYROIDISM IN RATS.

    Science.gov (United States)

    Nechiporuk, V; Zaichko, N; Korda, М; Melnyk, A; Koloshko, O

    2017-10-01

    Hyper- and hypothyroidism are some of the most common endocrinopathies that cause many metabolic disorders including amino acids metabolism. However, a specific molecular mechanism of thyroid hormones influence on sulphur-containing amino acids metabolism has not been established. The aim of our research was to investigate experimentally the influence of thyroid gland functional state on the main enzymatic systems of sulphur-containing amino acids metabolism in liver and kidneys, the content of homocysteine, cysteine and H2S in blood. The rats were administered with L-thyroxine and mercazolil to simulate the states of hyper- and hypothyroidism, which were confirmed by the content of fT3, fT4 and TSH in the blood. In liver and kidneys of the animals with hypothyroidism we observed the decrease in the activity of enzymes of remethylation cycle of S-adenosylmethioninsyntase, S-adenosylhomocysteinhyhdrolase, betaine-homocysteine methyltransferase. Suppression of transsulfuration transformation of homocysteine to cysteine in hypothyroidism was mainly due to the inhibition of cystathionine synthase activity of cystathionine-β-synthase, wherein cystathionase activity of cystathionine-γ-lyase was not changed. In animals with hypothyroidism we also noticed the inhibition of cysteine desulfunation reactions: the activity of enzymes of cystathionine-β-synthase, cystathionine-γ-lyase and cysteine aminotransferase significantly decreased in liver and kidneys. Experimental hyperthyroidism was accompanied by increase in activity of remethylation cycle enzymes, increase in cystationine synthase activity of cystathionine-β-synthase in liver and activity of these enzymes in kidneys. The simulation of hyperthyroidism led to the decrease of homocysteine concentration, and of hypothyroidism - to the increase of homocysteine and cysteine concentrations and reduced H2S content in blood of the animals. Thus, the significant risk factors for the development of atherosclerosis

  13. MOLECULAR COMPLEXES OF SULPHUR DIOXIDE WITH N,O-CONTAINING ORGANIC BASES (REVIEW

    Directory of Open Access Journals (Sweden)

    R. E. Khoma

    2016-10-01

    Full Text Available The literature data on the synthesis, stoichiometry, structure and relative stability of molecular  complexes of sulphur dioxide with N,O-containing organic bases have been systematized and  generalized. It was shown that the yield of the reaction product of sulfur dioxide with organic  bases (such as amines are strongly influenced by the conditions of synthesis: the nature of  the solvent (basicity, polarity, the temperature and SO2:L ratio in the reaction medium. The stoichiometry of SO2*nL molecular complexes depends on ligand denticity, as well as its  ability to H-bonding. The reaction of the sulfur oxide (IV with organic bases can give S←N and S←O complexes. With the increase of the value of base proton affinity the decrease ΔrSN values has been marked. Characteristic parameter Δr SN = r SN – a1(rS+ rN (where rSNis the S←N donor-acceptor bond length has been determined by microwave spectroscopy and X-ray analysis, rSand rNwere the tabulated values of the homopolar covalent radii of sulphur and nitrogen heteroatoms. The dependence of formation enthalpy of molecular complexes of basic amines and spectral characteristics has been noted; enthalpy-entropy compensation for S←N and S←O complex-es has been stated. Despite the limited experimental data on the thermodynamics of complex formation and the lengths of donor-acceptor bonds for the same compounds it has been found bond S←N strength in SO2 molecular complexes to depend on the intrinsic value of ΔrSN. The contribution of van der Waals forces and charge transfer forces to the formation of molecular complexes of sulphur dioxide has been stated.

  14. Sulphur enrichment in a sediment core from the central western continental margin of India

    Digital Repository Service at National Institute of Oceanography (India)

    Rao, P.S.; Rao, Ch.M.

    deposited in anoxic environment. Our study indicate that the excess sulphur is mainly due to the addition of sulphides from the shallow regions by mass sedimentation processes rather than water column sulphide formation as observed in anoxic environment...

  15. Response of sulphur dynamics in European catchments to decreasing sulphate deposition

    Czech Academy of Sciences Publication Activity Database

    Prechtel, A.; Alewell, C.; Armbruster, M.; Bittersohl, J.; Cullen, J.; Evans, C. D.; Helliwell, R.; Kopáček, Jiří; Marchetto, A.; Matzner, E.; Meesenburg, H.; Moldan, F.; Moritz, K.; Veselý, J.; Wright, R. F.

    2001-01-01

    Roč. 5, č. 3 (2001), s. 311-325 ISSN 1027-5606 R&D Projects: GA ČR GA206/00/0063 Grant - others:CEC RECOVER(XE) 2010-EVK1-CT-1999-00018; GMER(DE) PT BEO51-0339476; CEC(XE) EMERGE-EVK1-CT-1999-00032 Keywords : acidification reversal * sulphur * sulphate release Subject RIV: DJ - Water Pollution ; Quality Impact factor: 1.127, year: 2001

  16. Valorisation of waste ilmenite mud in the manufacture of sulphur polymer cement.

    Science.gov (United States)

    Contreras, Manuel; Gázquez, Manuel Jesús; García-Díaz, Irene; Alguacil, Francisco J; López, Félix A; Bolívar, Juan Pedro

    2013-10-15

    This paper reports the preparation of sulphur polymer cements (SPCs) incorporating waste ilmenite mud for use in concrete construction works. The ilmenite mud raw material and the mud-containing SPCs (IMC-SPCs) were characterised physico-chemically and radiologically. The optimal IMC-SPC mixture had a sulphur/mud ratio (w/w) of 1.05 (mud dose 20 wt%); this cement showed the greatest compressive strength (64 MPa) and the lowest water absorption coefficient (0.4 g cm(-2) at 28 days). Since ilmenite mud is enriched in natural radionuclides, such as radium isotopes (2.0·10(3) Bq kg(-1)(228)Ra and 5.0·10(2) Bq kg(-1)(226)Ra), the IMC-SPCs were subjected to leaching experiments, which showed their environmental impact to be negligible. The activity concentration indices for the different radionuclides in the IMC-SPCs containing 10% and 20% ilmenite mud met the demands of international standards for materials used in the construction of non-residential buildings. Copyright © 2013 Elsevier Ltd. All rights reserved.

  17. Nature of the Electrochemical Properties of Sulphur Substituted LiMn2O4 Spinel Cathode Material Studied by Electrochemical Impedance Spectroscopy

    Directory of Open Access Journals (Sweden)

    Monika Bakierska

    2016-08-01

    Full Text Available In this work, nanostructured LiMn2O4 (LMO and LiMn2O3.99S0.01 (LMOS1 spinel cathode materials were comprehensively investigated in terms of electrochemical properties. For this purpose, electrochemical impedance spectroscopy (EIS measurements as a function of state of charge (SOC were conducted on a representative charge and discharge cycle. The changes in the electrochemical performance of the stoichiometric and sulphur-substituted lithium manganese oxide spinels were examined, and suggested explanations for the observed dependencies were given. A strong influence of sulphur introduction into the spinel structure on the chemical stability and electrochemical characteristic was observed. It was demonstrated that the significant improvement in coulombic efficiency and capacity retention of lithium cell with LMOS1 active material arises from a more stable solid electrolyte interphase (SEI layer. Based on EIS studies, the Li ion diffusion coefficients in the cathodes were estimated, and the influence of sulphur on Li+ diffusivity in the spinel structure was established. The obtained results support the assumption that sulphur substitution is an effective way to promote chemical stability and the electrochemical performance of LiMn2O4 cathode material.

  18. Sulphur poisoning of palladium catalysts used for methane combustion: Effect of the support

    International Nuclear Information System (INIS)

    Escandon, Lara S.; Ordonez, Salvador; Vega, Aurelio; Diez, Fernando V.

    2008-01-01

    Four different supported palladium catalysts (using alumina, silica, zirconia and titania as supports), prepared by incipient wetness impregnation, were tested as catalysts for methane oxidation in presence of sulphur dioxide. The catalyst supported on zirconia showed the best performance, whereas the silica-supported one showed the fastest deactivation. Temperature-programmed desorption experiments of the poisoned catalysts suggest that SO 2 adsorption capacity of the support plays a key role in the catalyst poisoning. In order to study the effect of promoters, expected to improve the thermal stability and thioresistance of the catalyst, commercial zirconia modified by yttrium and lantane was tested as supports. It was found that the presence of these promoters does not improve the performance of the zirconia-supported catalyst. A deactivation model - considering two different active sites (fresh and poisoning), pseudo-first order dependence on methane concentration and poisoning rate depending on sulphur concentration and fraction of non-poisoned palladium - was used for modelling the deactivation behaviour

  19. Treatment of reduced sulphur compounds and SO2 by Gas Phase Advanced Oxidation

    DEFF Research Database (Denmark)

    Meusinger, Carl; Bluhme, Anders Brostrøm; Ingemar, Jonas L.

    2017-01-01

    Reduced sulphur compounds (RSCs) emitted from pig farms are a major problem for agriculture, due to their health and environmental impacts and foul odour. This study investigates the removal of RSCs, including H2S, and their oxidation product SO2 using Gas Phase Advanced Oxidation (GPAO). GPAO...... is a novel air cleaning technique which utilises accelerated atmospheric chemistry to oxidise pollutants before removing their oxidation products as particles. Removal efficiencies of 24.5% and 3.9% were found for 461 ppb of H2S and 714 ppb of SO2 in a laboratory system (volumetric flow Q = 75 m3/h......). A numerical model of the reactor system was developed to explore the basic features of the system; its output was in fair agreement with the experiment. The model verified the role of OH radicals in initiating the oxidation chemistry. All sulphur removed from the gas phase was detected as particulate matter...

  20. The diagnostic value of 111In-oxine or 99mTc-sulphur-colloid-labelled leucocytes in patients with inflammation of bones and hip endoprothesis

    International Nuclear Information System (INIS)

    Kostadinowa, I.; Dontschev, M.; Dojtschinov, A.; Kynev, W.; Kowatschewa, S.

    1990-01-01

    Scintigraphy with leukocytes, labelled with 99m Tc sulphur colloid or 111 In-oxide, in 41 patients with suspected inflammation in endoprothetic hip joints (n=23) or infectious complications after femoral fracture (n=18) has shown to be a highly specific and useful tool in orthopaedic routine diagnosis. (orig.) [de

  1. Formation and colloidal behaviour of elemental sulphur produced from the biological oxidation of hydrogensulphide

    NARCIS (Netherlands)

    Janssen, A.J.H.

    1996-01-01


    The formation and aggregation of elemental sulphur from the microbiological oxidation of hydrogensulphide (H 2 S) by a mixed population of aerobic Thiobacillus -like bacteria has been investigated. Sulphide is

  2. Evaluation of modified atmosphere bag and sulphur dioxide concentrations applied on highbush blueberries fruit (Vaccinium corymbosum L.) cv. Emerald

    OpenAIRE

    Rodríguez, Mario; Wyss, Anddy; Hormazábal, Nelson

    2015-01-01

    Aiming to evaluate techniques for modified atmosphere and application of sulphur anhydride upon parameters of quality of postharvest on blueberry fruit (Vaccinium corymbosum L.) cv. Emerald, an experiment of six treatments was conducted, given by the combination of two factors, modified atmosphere (with and without) and different concentrations of sulphur dioxide (generated by 0, 1 and 2 g of sodium metabisulphite) during 7, 14, 21 and 28 days at 0 °C. The dose of 2 g of modified atmosphere s...

  3. A Colonial Conundrum: Boy with Sulphur-Crested Cockatoo

    Directory of Open Access Journals (Sweden)

    Elisabeth Findlay

    2008-12-01

    Full Text Available This paper presents a detailed analysis of the perplexing painting Boy with Sulphur-Crested Cockatoo. Unfortunately, there is little information on the provenance of the portrait, including the identity of the artist, sitter and patron. It will be argued that it is the work of Augustus Earle and that it is a portrait of Daniel Cooper II and was commissioned by his uncle, also named Daniel Cooper. The aim of this article is to start to unravel the ambiguities of the image, and I suggest that the painting is a strong statement on the rights of freed convicts in Australian colonial society

  4. Influence of phosphorous and sulphur as well as grain size on creep in pure copper

    International Nuclear Information System (INIS)

    Andersson, Henrik; Seitisleam, Facredin; Sandstroem, Rolf

    1999-12-01

    Uniaxial creep tests have been performed at 175 deg C for extruded oxygen-free copper. The effect of different contents of phosphorous and sulphur as well as different grain sizes have been studied. The copper with < 1 ppm phosphorous and with a 6 ppm sulphur content showed significantly lower creep life and ductility than batches with higher P content. An increase of the P content to 29 ppm increased the creep life and ductility, but a further increase did not affect the properties further. A similar drop in the creep properties was found in the material with a grain size of about 2000 μm. A reduction of the mean grain size to 800 μm had a beneficial effect on the creep ductility. A further reduction of the grain size did not give any further improvements. All tests except those with a phosphorous content of less than 1 ppm P and those with a mean grain size of about 2000 μm failed at an elongation greater than 20%, most of them at 30-40%. The variation in sulphur content from 6 to 12 ppm did not affect the creep properties. The main creep rupture mechanisms were found to be cavitation and microcracking at the grain boundaries. Master curves for extrapolation are provided for creep rupture as well as for 5% and 10% creep strain

  5. Environmental and economic gains of the conversion of the Zvolen (Slovakia) district CHP plant from low quality brown coal combustion to co-firing of biomass and low-sulphur brown coal

    International Nuclear Information System (INIS)

    Ilavsky, Jan; Jankovsky, Julius

    2006-01-01

    Zvolen CHP plant was originally commissioned in 1954. Overall installed output is 311 MW in heat production and 44,3 MW in power. Annual supply to the consumers was 788,910 GJ of heat and 102,459 GJ of electricity in 2004. Some 60 % of the heat production was used for heat and hot water supply to more than 9,000 houses and apartments and 40 % to industrial consumers. It uses pulverized lignite with up to 1 % of sulphur content as fuel. The content of sulphur in emitted flue gas is as high as 3,500-4,000 mg SO 2 /m 3 . It causes serious environmental problems in the region. New national limits for greenhouse gases emissions are 1.700 mg SO 2 /m 3 and 600 mg NO x /m 3 with effect from 1 January 2007. CHP is not able to achieve them without substantial improvement of technology with very high investment costs. Several alternatives of technical changes have been analysed in a study. Shift from lignite to low-sulphur content brown coal with co-firing of biomass has been identified economically most feasible and environmentally acceptable solution. The paper presents results of the study analysing the whole chain from biomass resources in the region up to the technical solutions for boilers reconstruction. The first part of the study was focused at identification of biomass resources for energy use from forestry, wood processing industry and agriculture. Ecological, economic and operational factors limiting utilization of potential biomass resources were identified and factored into calculations. Two boilers, each of them with the output of 108 MW t , will be reconstructed for co-firing of pulverized low sulphur content brown coal and biomass. Biomass will share up to 30% of the combusted fuel. After the reconstruction one boiler will remain with the same output of 108 MW t and the other will be with the output of 65 MW t . Power will be produced by the back pressure 25 MW e turbine. Chips will be stored in 9.000 m 3 open depot and in 3.000 m 3 silo. Chips will be fed

  6. Eaglet property, southeastern British Columbia: Re-Os geochronology, sulphur isotopes, and thermobarometry

    Czech Academy of Sciences Publication Activity Database

    Hora, Z. D.; Stein, H.; Žák, Karel; Dobeš, P.

    2018-01-01

    Roč. 2017, č. 1 (2018), s. 157-166 ISSN 0381-243X Institutional support: RVO:67985831 Keywords : Eaglet deposit * MINFILE 093A 046 * fluorite * celestite * molybdenite * sulphur isotopes * Re-Os geochronology * fluid inclusion microthermobarometry Subject RIV: DB - Geology ; Mineralogy OBOR OECD: Geology http://cmscontent.nrs.gov.bc.ca/geoscience/PublicationsCatalogue/Fieldwork/Documents/2017/P2018-1.pdf

  7. Computer Simulation of Microsegregation of Sulphur and Manganese and Formation of MnS Inclusions while Casting Rail Steel

    Directory of Open Access Journals (Sweden)

    Kalisz D.

    2016-12-01

    Full Text Available The quality of rail steel is conditioned by its high mechanic qualities, which greatly depend on the presence of undesired nonmetallic inclusions. The paper is devoted to the segregation of components, mainly sulphur, and the formation of manganese sulphide in the process of steel solidification, at the casting rate of 100 and 500 K/min. Sulphur is a steel component which disadvantageously influences its numerous parameters. The oxide-sulphide and sulphide precipitations cause cracks and lower the strength of the material. This phenomenon was modeled with the use of author’s computer program based on Matsumiya interdendritic microsegregation model. The main assumptions of this model and thermodynamic conditions of inclusion formation during casting of steel are discussed in this paper. Two cases were analyzed: in the first one the MnS was assumed to form a pure and constant compound, whereas in the other one the manganese sulfide was precipitated as a component of a liquid oxide solution, and its activity was lower than unity. The final conclusion is that chemical composition of steel is the major parameter deciding about the formation of MnS inclusions.

  8. Chronic aspartame intake causes changes in the trans-sulphuration pathway, glutathione depletion and liver damage in mice

    Directory of Open Access Journals (Sweden)

    Isabela Finamor

    2017-04-01

    Full Text Available No-caloric sweeteners, such as aspartame, are widely used in various food and beverages to prevent the increasing rates of obesity and diabetes mellitus, acting as tools in helping control caloric intake. Aspartame is metabolized to phenylalanine, aspartic acid, and methanol. Our aim was to study the effect of chronic administration of aspartame on glutathione redox status and on the trans-sulphuration pathway in mouse liver. Mice were divided into three groups: control; treated daily with aspartame for 90 days; and treated with aspartame plus N-acetylcysteine (NAC. Chronic administration of aspartame increased plasma alanine aminotransferase (ALT and aspartate aminotransferase activities and caused liver injury as well as marked decreased hepatic levels of reduced glutathione (GSH, oxidized glutathione (GSSG, γ-glutamylcysteine ​​(γ-GC, and most metabolites of the trans-sulphuration pathway, such as cysteine, S-adenosylmethionine (SAM, and S-adenosylhomocysteine ​​(SAH. Aspartame also triggered a decrease in mRNA and protein levels of the catalytic subunit of glutamate cysteine ligase (GCLc and cystathionine γ-lyase, and in protein levels of methionine adenosyltransferase 1A and 2A. N-acetylcysteine prevented the aspartame-induced liver injury and the increase in plasma ALT activity as well as the decrease in GSH, γ-GC, cysteine, SAM and SAH levels and GCLc protein levels. In conclusion, chronic administration of aspartame caused marked hepatic GSH depletion, which should be ascribed to GCLc down-regulation and decreased cysteine levels. Aspartame triggered blockade of the trans-sulphuration pathway at two steps, cystathionine γ-lyase and methionine adenosyltransferases. NAC restored glutathione levels as well as the impairment of the trans-sulphuration pathway.

  9. Chronic aspartame intake causes changes in the trans-sulphuration pathway, glutathione depletion and liver damage in mice.

    Science.gov (United States)

    Finamor, Isabela; Pérez, Salvador; Bressan, Caroline A; Brenner, Carlos E; Rius-Pérez, Sergio; Brittes, Patricia C; Cheiran, Gabriele; Rocha, Maria I; da Veiga, Marcelo; Sastre, Juan; Pavanato, Maria A

    2017-04-01

    No-caloric sweeteners, such as aspartame, are widely used in various food and beverages to prevent the increasing rates of obesity and diabetes mellitus, acting as tools in helping control caloric intake. Aspartame is metabolized to phenylalanine, aspartic acid, and methanol. Our aim was to study the effect of chronic administration of aspartame on glutathione redox status and on the trans-sulphuration pathway in mouse liver. Mice were divided into three groups: control; treated daily with aspartame for 90 days; and treated with aspartame plus N-acetylcysteine (NAC). Chronic administration of aspartame increased plasma alanine aminotransferase (ALT) and aspartate aminotransferase activities and caused liver injury as well as marked decreased hepatic levels of reduced glutathione (GSH), oxidized glutathione (GSSG), γ-glutamylcysteine ​​(γ-GC), and most metabolites of the trans-sulphuration pathway, such as cysteine, S-adenosylmethionine (SAM), and S-adenosylhomocysteine ​​(SAH). Aspartame also triggered a decrease in mRNA and protein levels of the catalytic subunit of glutamate cysteine ligase (GCLc) and cystathionine γ-lyase, and in protein levels of methionine adenosyltransferase 1A and 2A. N-acetylcysteine prevented the aspartame-induced liver injury and the increase in plasma ALT activity as well as the decrease in GSH, γ-GC, cysteine, SAM and SAH levels and GCLc protein levels. In conclusion, chronic administration of aspartame caused marked hepatic GSH depletion, which should be ascribed to GCLc down-regulation and decreased cysteine levels. Aspartame triggered blockade of the trans-sulphuration pathway at two steps, cystathionine γ-lyase and methionine adenosyltransferases. NAC restored glutathione levels as well as the impairment of the trans-sulphuration pathway. Copyright © 2017. Published by Elsevier B.V.

  10. Ultrasound-assisted extraction for total sulphur measurement in mine tailings

    International Nuclear Information System (INIS)

    Khan, Adnan Hossain; Shang, Julie Q.; Alam, Raquibul

    2012-01-01

    Highlights: ► We develop a total sulphur measuring procedure of mine tailings. ► Ultrasound is used in the sample pre-treatment process. ► Full factorial design is applied to identify the best level of effecting factors. - Abstract: A sample preparation method for percentage recovery of total sulphur (%S) in reactive mine tailings based on ultrasound-assisted digestion (USAD) and inductively coupled plasma-optical emission spectroscopy (ICP-OES) was developed. The influence of various methodological factors was screened by employing a two-level and three-factor (2 3 ) full factorial design and using KZK-1, a sericite schist certified reference material (CRM), to find the optimal combination of studied factors and %S. Factors such as the sonication time, temperature and acid combination were studied, with the best result identified as 20 min of sonication, 80 °C temperature and 1 ml of HNO 3 :1 ml of HCl, which can achieve 100% recovery for the selected CRM. Subsequently a fraction of the 2 3 full factorial design was applied to mine tailings. The percentage relative standard deviation (%RSD) for the ultrasound method is less than 3.0% for CRM and less than 6% for the mine tailings. The investigated method was verified by X-ray diffraction analysis. The USAD method compared favorably with existing methods such as hot plate assisted digestion method, X-ray fluorescence and LECO™-CNS method.

  11. Influence of farmyard manure on the utilization of labelled phosphorus and sulphur by brinjal (Solanum Melongena L.)

    International Nuclear Information System (INIS)

    Bhattacharya, Pratap; Ghosh, G.

    2002-01-01

    Influence of FYM, phosphorus and sulphur application on dry matter yield, fertilizer phosphorus and sulphur uptake and their utilization by brinjal (Solanum Melongena L.) fruits and leaves were studied by a pot culture experiment in a Typic ustocrept soil of IARI farm. Two levels if FYM, viz., 0 and 25 t ha -1 four levels of phosphorus viz., 0, 30, 60 and 90 kg P 2 O 5 ha -1 and three levels of sulphur viz., 0, 15 and 30 kg ha -1 were applied in all possible combinations. Maximum dry weight of fruits and leaves was reported due to combined application of 15 kg S ha -1 level. 60 kg P 2 O 5 ha -1 with FYM. Combined effect of FYM with lower level of P (30 kg P 2 O 5 ha -1 ) and 30 kg ha -1 level of S gave higher per cent utilization of applied P by fruits and leaves. On the other hand combined effect of FYM with lower dose of S (15 kg ha -1 ) and 60 kg ha -1 level of P 2 O 5 gave higher per cent utilization of applied S by brinjal. (author)

  12. High energy neutron radiography

    International Nuclear Information System (INIS)

    Gavron, A.; Morley, K.; Morris, C.; Seestrom, S.; Ullmann, J.; Yates, G.; Zumbro, J.

    1996-01-01

    High-energy spallation neutron sources are now being considered in the US and elsewhere as a replacement for neutron beams produced by reactors. High-energy and high intensity neutron beams, produced by unmoderated spallation sources, open potential new vistas of neutron radiography. The authors discuss the basic advantages and disadvantages of high-energy neutron radiography, and consider some experimental results obtained at the Weapons Neutron Research (WNR) facility at Los Alamos

  13. Kinetics and thermodynamics of aluminium dissolution in 1.0M sulphuric acid containing chloride ions

    Energy Technology Data Exchange (ETDEWEB)

    Abdel-Gaber, A.M. [Department of Chemistry, Faculty of Science, Alexandria University, P.O. Box 426, Ibrahimia, Alexandria 21321 (Egypt)]. E-mail: ashrafmoustafa@yahoo.com; Abd-El-Nabey, B.A. [Department of Chemistry, Faculty of Science, Alexandria University, P.O. Box 426, Ibrahimia, Alexandria 21321 (Egypt); Sidahmed, I.M. [Department of Chemistry, Faculty of Science, Alexandria University, P.O. Box 426, Ibrahimia, Alexandria 21321 (Egypt); El-Zayady, A.M. [Department of Chemistry, Faculty of Science, Alexandria University, P.O. Box 426, Ibrahimia, Alexandria 21321 (Egypt); Saadawy, M. [Department of Chemistry, Faculty of Science, Alexandria University, P.O. Box 426, Ibrahimia, Alexandria 21321 (Egypt)

    2006-08-01

    The dissolution of aluminium in 1M sulphuric acid solutions containing different chloride ion concentrations (0.01-0.06M) were studied at 25, 30, 35 and 40deg. C using electrochemical impedance spectroscopy (EIS) technique and polarization curves measurements. The kinetic rate equation, under the experimental condition described, was derived and found to verify the following relationship:V=k{sub obs}K{sub 2}C{sub Cl{sup -}}{sup n}1+K{sub 2}C{sub Cl{sup -}}{sup n}where V is the corrosion rate, k{sub obs} and K{sub 2} are the dissolution rate constant of aluminium oxide-chloride complex and the equilibrium constant of chloride ions adsorbed at aluminium oxide surface, respectively. The kinetic and thermodynamic energy parameters were calculated and their values indicate that chloride ions are chemisorbed onto the aluminium oxide surface and the formation of oxide-chloride complex is the rate-determining step.

  14. The recuperation of sulphuric acid out of contaminated solutions by electro electrodialysis

    International Nuclear Information System (INIS)

    Cattoir, S.

    1997-05-01

    The dismantling of a nuclear reactor results in large amounts of contaminated waste. The amount of waste is minimized by so-called decontamination processes. These decontamination processes result in decontaminated metal as well as contaminated effluents, containing acid and metal salts. Standard treatment of these effluents involves neutralisation of the acid using sodium hydroxide, resulting in the precipitation of hydroxides; and evaporation of the solvent. However, if the acid is extracted out of the decontamination effluents prior to neutralisation, this acid can be re-used in the decontamination process, substantially reducing the final waste. This report investigates the possibility of using Electro Electrodialysis (EED) for the extraction of 900 moles of sulphuric acid out of a 1 m 3 contaminated solution, containing 22 kg of ferrous, chromous, cerous and nickel ions and 1000 moles of sulphuric acid. EED removes acids out of acid/salts solutions, using an electrolyser equipped with an anionic membrane: the acid-anion is displaced by migration through the membrane while the proton is displaced by electrolysis. This report gives a full description of the technique, the lab-scale apparatus, the analyses involved in studying the technique on lab-scale or monitoring it on full scale, the choice of electrode and membrane and of process parameters such as temperature and current density. On lab scale, EED can displace 90% of the acid out of the acid/salt solution just described, at a current density as high as 0.14 A.cm -2 , at 50 degrees Celsius, if the cathode and the anode are of smoothed platina or of platinised titanium, and the anion selective membrane is the Neosepta AMH -membrane of Tokuyama. The study of EED still needs to be completed with a further study of metal deposition on the cathode, and a comparison of the technique to other (electro)membrane techniques

  15. Short term effects of ambient sulphur dioxide and particulate matter on mortality in 12 European cities : Results from time series data from the APHEA project

    NARCIS (Netherlands)

    Katsouyanni, K; Touloumi, G; Spix, C; Schwartz, J; Balducci, F; Medina, S; Rossi, G; Wojtyniak, B; Sunyer, J; Bacharova, L; Schouten, JP; Ponka, A; Anderson, HR

    1997-01-01

    Objectives: To carry out a prospective combined quantitative analysis of the associations between all cause mortality and ambient particulate matter and sulphur dioxide. . Design: Analysis of time series data on daily number of deaths from all causes and concentrations of sulphur dioxide and

  16. High to ultra-high power electrical energy storage.

    Science.gov (United States)

    Sherrill, Stefanie A; Banerjee, Parag; Rubloff, Gary W; Lee, Sang Bok

    2011-12-14

    High power electrical energy storage systems are becoming critical devices for advanced energy storage technology. This is true in part due to their high rate capabilities and moderate energy densities which allow them to capture power efficiently from evanescent, renewable energy sources. High power systems include both electrochemical capacitors and electrostatic capacitors. These devices have fast charging and discharging rates, supplying energy within seconds or less. Recent research has focused on increasing power and energy density of the devices using advanced materials and novel architectural design. An increase in understanding of structure-property relationships in nanomaterials and interfaces and the ability to control nanostructures precisely has led to an immense improvement in the performance characteristics of these devices. In this review, we discuss the recent advances for both electrochemical and electrostatic capacitors as high power electrical energy storage systems, and propose directions and challenges for the future. We asses the opportunities in nanostructure-based high power electrical energy storage devices and include electrochemical and electrostatic capacitors for their potential to open the door to a new regime of power energy.

  17. High-energy detector

    Science.gov (United States)

    Bolotnikov, Aleksey E [South Setauket, NY; Camarda, Giuseppe [Farmingville, NY; Cui, Yonggang [Upton, NY; James, Ralph B [Ridge, NY

    2011-11-22

    The preferred embodiments are directed to a high-energy detector that is electrically shielded using an anode, a cathode, and a conducting shield to substantially reduce or eliminate electrically unshielded area. The anode and the cathode are disposed at opposite ends of the detector and the conducting shield substantially surrounds at least a portion of the longitudinal surface of the detector. The conducting shield extends longitudinally to the anode end of the detector and substantially surrounds at least a portion of the detector. Signals read from one or more of the anode, cathode, and conducting shield can be used to determine the number of electrons that are liberated as a result of high-energy particles impinge on the detector. A correction technique can be implemented to correct for liberated electron that become trapped to improve the energy resolution of the high-energy detectors disclosed herein.

  18. Energy Systems High-Pressure Test Laboratory | Energy Systems Integration

    Science.gov (United States)

    Facility | NREL Energy Systems High-Pressure Test Laboratory Energy Systems High-Pressure Test Laboratory In the Energy Systems Integration Facility's High-Pressure Test Laboratory, researchers can safely test high-pressure hydrogen components. Photo of researchers running an experiment with a hydrogen fuel

  19. Satellite Monitoring of Ash and Sulphur Dioxide for the mitigation of Aviation Hazards: Part II. Validation of satellite-derived Volcanic Sulphur Dioxide Levels.

    Science.gov (United States)

    Koukouli, MariLiza; Balis, Dimitris; Dimopoulos, Spiros; Clarisse, Lieven; Carboni, Elisa; Hedelt, Pascal; Spinetti, Claudia; Theys, Nicolas; Tampellini, Lucia; Zehner, Claus

    2014-05-01

    The eruption of the Icelandic volcano Eyjafjallajökull in the spring of 2010 turned the attention of both the public and the scientific community to the susceptibility of the European airspace to the outflows of large volcanic eruptions. The ash-rich plume from Eyjafjallajökull drifted towards Europe and caused major disruptions of European air traffic for several weeks affecting the everyday life of millions of people and with a strong economic impact. This unparalleled situation revealed limitations in the decision making process due to the lack of information on the tolerance to ash of commercial aircraft engines as well as limitations in the ash monitoring and prediction capabilities. The European Space Agency project Satellite Monitoring of Ash and Sulphur Dioxide for the mitigation of Aviation Hazards, was introduced to facilitate the development of an optimal End-to-End System for Volcanic Ash Plume Monitoring and Prediction. This system is based on comprehensive satellite-derived ash plume and sulphur dioxide [SO2] level estimates, as well as a widespread validation using supplementary satellite, aircraft and ground-based measurements. The validation of volcanic SO2 levels extracted from the sensors GOME-2/MetopA and IASI/MetopA are shown here with emphasis on the total column observed right before, during and after the Eyjafjallajökull 2010 eruptions. Co-located ground-based Brewer Spectrophotometer data extracted from the World Ozone and Ultraviolet Radiation Data Centre, WOUDC, were compared to the different satellite estimates. The findings are presented at length, alongside a comprehensive discussion of future scenarios.

  20. Very high energy colliders

    International Nuclear Information System (INIS)

    Richter, B.

    1986-03-01

    The luminosity and energy requirements are considered for both proton colliders and electron-positron colliders. Some of the basic design equations for high energy linear electron colliders are summarized, as well as design constraints. A few examples are given of parameters for very high energy machines. 4 refs., 6 figs

  1. Suncor Energy 1996 annual report

    International Nuclear Information System (INIS)

    1996-01-01

    A review of revenues, expenditures and earnings, and 1996 operational highlights of Suncor Energy were presented. Suncor Energy is a leader in oil sands extraction and upgrading technology. In 1996 the company increased its earnings to $187 million, an increase of 24% over the previous year. It achieved record production of 77,600 barrels per day, up from 76,000 barrels per day in 1995. It commissioned a $190 million sulphur dioxide reduction plant which, in concert with other improvements, will cut sulphur dioxide emissions to 25 per cent of 1990 levels. It achieved regulatory approvals on plant expansion and the Steepbank Mine project. It began construction of the bridge across the Athabasca River that will connect Suncor's oil sands plant with the new Steepbank Mine. It added 30 million barrels of oil equivalent of proven new reserves and initiated the first phase of the Burnt Lake heavy oil project. It repositioned and restructured its wholesale and retail marketing businesses in Ontario and Quebec and positioned its Sunoco branded retail business in the top 10 per cent of its markets. Goals for 1997, for each of the company's three business divisions, were also given prominent attention. tabs., figs

  2. Synthesis of palladium@gold nanoalloys/nitrogen and sulphur-functionalized multiple graphene aerogel for electrochemical detection of dopamine

    Energy Technology Data Exchange (ETDEWEB)

    Li, Ruiyi; Yang, Tingting [School of Chemical and Material Engineering, Jiangnan University, Wuxi 214122 (China); Li, Zaijun, E-mail: zaijunli@jiangnan.edu.cn [School of Chemical and Material Engineering, Jiangnan University, Wuxi 214122 (China); Key Laboratory of Food Colloids and Biotechnology, Ministry of Education, Wuxi 214122 (China); Gu, Zhiguo; Wang, Guangli; Liu, Junkang [School of Chemical and Material Engineering, Jiangnan University, Wuxi 214122 (China)

    2017-02-15

    Integration of noble metal nanomaterials on graphene nanosheets potentially paves one way to improve their electronic, chemical and electrochemical properties. The study reported synthesis of palladium@gold nanoalloys/nitrogen and sulphur-functionalized multiple graphene aerogel composite (Pd@Au/N,S-MGA). The as-prepared composite offers a well-defined three-dimensional architecture with rich of mesopores. The Pd@Au nanoalloys were dispersed on the graphene framework networks and their active sites were fully exposed. The unique structure achieves to ultra high electron/ion conductivity, electrocatalytic activity and structural stability. The sensor based on the Pd@Au/N,S-MGA creates ultrasensitive electrochemical response towards dopamine due to significantly electrochemical synergy between Pd, Au and N,S-MGA. Its differential pulse voltammetric signal linearly increases with the increase of dopamine concentration in the range from 1.0 × 10{sup −9} M to 4.0 × 10{sup −5} M with the detection limit of 3.6 × 10{sup −10} M (S/N = 3). The analytical method provides the advantage of sensitivity, reproducibility, rapidity and long-term stability. It has been successfully applied in the detection of trace dopamine in biological samples. The study also opens a window on the electronic properties of graphene aerogel and metal nanomaterials as well their nanohybrids to meet needs of further applications as nanoelectronics in diagnosis, bioanalysis and catalysis. - Graphical abstract: We reported a new palladium@gold nanoalloys/nitrogen and sulphur-functionalized multiple graphene aerogel. The sensor based on the nanohybrid exhibits ultrahigh sensitivity, reproducibility and stability to electrochemical detection of dopamine. - Highlights: • We reported Pd@A/nitrogen and sulphur-functionalized multiple graphene aerogel. • The nanohybrid offers unique three-dimensional architecture with rich of mesopores. • The architecture achieve to ultrahigh

  3. Synthesis of palladium@gold nanoalloys/nitrogen and sulphur-functionalized multiple graphene aerogel for electrochemical detection of dopamine

    International Nuclear Information System (INIS)

    Li, Ruiyi; Yang, Tingting; Li, Zaijun; Gu, Zhiguo; Wang, Guangli; Liu, Junkang

    2017-01-01

    Integration of noble metal nanomaterials on graphene nanosheets potentially paves one way to improve their electronic, chemical and electrochemical properties. The study reported synthesis of palladium@gold nanoalloys/nitrogen and sulphur-functionalized multiple graphene aerogel composite (Pd@Au/N,S-MGA). The as-prepared composite offers a well-defined three-dimensional architecture with rich of mesopores. The Pd@Au nanoalloys were dispersed on the graphene framework networks and their active sites were fully exposed. The unique structure achieves to ultra high electron/ion conductivity, electrocatalytic activity and structural stability. The sensor based on the Pd@Au/N,S-MGA creates ultrasensitive electrochemical response towards dopamine due to significantly electrochemical synergy between Pd, Au and N,S-MGA. Its differential pulse voltammetric signal linearly increases with the increase of dopamine concentration in the range from 1.0 × 10"−"9 M to 4.0 × 10"−"5 M with the detection limit of 3.6 × 10"−"1"0 M (S/N = 3). The analytical method provides the advantage of sensitivity, reproducibility, rapidity and long-term stability. It has been successfully applied in the detection of trace dopamine in biological samples. The study also opens a window on the electronic properties of graphene aerogel and metal nanomaterials as well their nanohybrids to meet needs of further applications as nanoelectronics in diagnosis, bioanalysis and catalysis. - Graphical abstract: We reported a new palladium@gold nanoalloys/nitrogen and sulphur-functionalized multiple graphene aerogel. The sensor based on the nanohybrid exhibits ultrahigh sensitivity, reproducibility and stability to electrochemical detection of dopamine. - Highlights: • We reported Pd@A/nitrogen and sulphur-functionalized multiple graphene aerogel. • The nanohybrid offers unique three-dimensional architecture with rich of mesopores. • The architecture achieve to ultrahigh electron

  4. European transboundary acidifying air pollution. Ten years calculated fields and budgets to the end of the first Sulphur Protocol

    Energy Technology Data Exchange (ETDEWEB)

    Barrett, K.; Seland, Oe.; Foss, A.; Mylona, S.; Sandnes, H.; Styve, H.; Tarrason, L.

    1995-07-01

    The Cooperative Programme for the Monitoring and Evaluation of the Long Range Transmission and Air Pollutants in Europe, EMEP, plays an integral part in data collection and scientific cooperation for implementation of the 1979 Geneva Convention on Long Range Transboundary Air Pollution. Within EMEP, the Meteorological Synthesizing Centre - West (MSC-W) is an international technical centre. The purpose of the MSC-W, focusing in part on acidifying substances, is to estimate the concentrations of relevant sulphur and nitrogen pollutants across Europe on the basis of emission information and meteorological data, and to estimate the transboundary fluxes of these substances. Responding to these specific obligations, the report presents calculations of sulphur and nitrogen concentrations and depositions and of their transboundary fluxes. The calculations are performed by the receptor oriented one layer trajectory (Lagrangian) acid deposition model, which during 1995 has been used to estimate acidifying pollutant fluxes for the ten year period 1985-1994. This corresponds to the period between initial signing and conclusion of the first Sulphur Protocol, signed in Helsinki in 1985. 90 refs., 42 figs., 43 tabs.

  5. Air quality in the Kootenays: fine particulate (PM{sub 1}0) airborne metals and sulphur dioxide levels, 1993-1999

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    Air quality monitoring data collected in the Kootenays over a seven year period from 1993 to 1999 are summarized in an effort to inform the public about air quality in the Kootenays and to assist them in understanding air quality monitoring results. Data includes hourly (TEOM) and weekly (NAPS) data for particulate matter (PM{sub 1}0) airborne metals (arsenic, cadmium, lead and zinc) and sulphur dioxide. Analysis of monitoring data showed that particulate matter levels remained constant in most communities, with Johnson Lake and Slocan reporting the lowest levels, while Golden had the highest values during this period. Trail-Butler Park showed a clear declining trend in PM{sub 1}0. Airborne metals and sulphur dioxide levels have decreased in the Kootenays during the seven year period, with only occasional exceedances of both Level A and B air quality objectives in some communities. The report includes a detailed description of the sampling methodology and the analyzed results for PM{sub 1}0, airborne metals and sulphur dioxide for 10 communities in the region. 6 refs., 1 tab., 16 figs., 1 map.

  6. Removal of sulphur-containing odorants from fuel gases for fuel cell-based combined heat and power applications

    Energy Technology Data Exchange (ETDEWEB)

    De Wild, P.J.; Nyqvist, R.G.; De Bruijn, F.A.; Stobbe, E.R. [ECN Hydrogen and Clean Fossil Fuels, Petten (Netherlands)

    2006-02-15

    Natural gas (NG) and liquefied petroleum gas (LPG) are important potential feedstocks for the production of hydrogen for fuel cell-based (e.g. proton exchange membrane fuel cells (PEMFC)) or solid oxide fuel Cells (SOFC) combined heat and power (CHP) applications. To prevent detrimental effects on the (electro)catalysts in fuel cell-based combined heat and power installations (FC-CHP), sulphur removal from the feedstock is mandatory. An experimental bench-marking study of adsorbents has identified several candidates for the removal of sulphur containing odorants at low temperature. Among these adsorbents a new material has been discovered that offers an economically attractive means to remove TetraHydroThiophene (THT), the main European odorant, from natural gas at ambient temperature. The material is environmentally benign, easy to use and possesses good activity (residual sulphur levels below 20 ppbv) and capacity for the common odorant THT in natural gas. When compared to state-of-the-art metal-promoted active carbon the new material has a THT uptake capacity that is up to 10 times larger, depending on temperature and pressure. Promoted versions of the new material have shown potential for the removal of THT at higher temperatures and/or for the removal of other odorants such as mercaptans from natural gas or from LPG.

  7. Removal of sulphur-containing odorants from fuel gases for fuel cell-based combined heat and power applications

    Energy Technology Data Exchange (ETDEWEB)

    de Wild, P.J.; Nyqvist, R.G.; de Bruijn, F.A.; Stobbe, E.R. [Energy Research Centre of The Netherlands ECN, P.O. Box 1, 1755 ZG Petten (Netherlands)

    2006-09-22

    Natural gas (NG) and liquefied petroleum gas (LPG) are important potential feedstocks for the production of hydrogen for fuel cell-based (e.g. proton exchange membrane fuel cells (PEMFC) or solid oxide fuel Cells (SOFC) combined heat and power (CHP) applications. To prevent detrimental effects on the (electro)catalysts in fuel cell-based combined heat and power installations (FC-CHP), sulphur removal from the feedstock is mandatory. An experimental bench-marking study of adsorbents has identified several candidates for the removal of sulphur containing odorants at low temperature. Among these adsorbents a new material has been discovered that offers an economically attractive means to remove TetraHydroThiophene (THT), the main European odorant, from natural gas at ambient temperature. The material is environmentally benign, easy to use and possesses good activity (residual sulphur levels below 20ppbv) and capacity for the common odorant THT in natural gas. When compared to state-of-the-art metal-promoted active carbon the new material has a THT uptake capacity that is up to 10 times larger, depending on temperature and pressure. Promoted versions of the new material have shown potential for the removal of THT at higher temperatures and/or for the removal of other odorants such as mercaptans from natural gas or from LPG. (author)

  8. Ultrasound-assisted extraction for total sulphur measurement in mine tailings

    Energy Technology Data Exchange (ETDEWEB)

    Khan, Adnan Hossain, E-mail: ad_li2@yahoo.com [Department of Civil and Environmental Engineering, University of Western Ontario (Canada); Shang, Julie Q.; Alam, Raquibul [Department of Civil and Environmental Engineering, University of Western Ontario (Canada)

    2012-10-15

    Highlights: Black-Right-Pointing-Pointer We develop a total sulphur measuring procedure of mine tailings. Black-Right-Pointing-Pointer Ultrasound is used in the sample pre-treatment process. Black-Right-Pointing-Pointer Full factorial design is applied to identify the best level of effecting factors. - Abstract: A sample preparation method for percentage recovery of total sulphur (%S) in reactive mine tailings based on ultrasound-assisted digestion (USAD) and inductively coupled plasma-optical emission spectroscopy (ICP-OES) was developed. The influence of various methodological factors was screened by employing a two-level and three-factor (2{sup 3}) full factorial design and using KZK-1, a sericite schist certified reference material (CRM), to find the optimal combination of studied factors and %S. Factors such as the sonication time, temperature and acid combination were studied, with the best result identified as 20 min of sonication, 80 Degree-Sign C temperature and 1 ml of HNO{sub 3}:1 ml of HCl, which can achieve 100% recovery for the selected CRM. Subsequently a fraction of the 2{sup 3} full factorial design was applied to mine tailings. The percentage relative standard deviation (%RSD) for the ultrasound method is less than 3.0% for CRM and less than 6% for the mine tailings. The investigated method was verified by X-ray diffraction analysis. The USAD method compared favorably with existing methods such as hot plate assisted digestion method, X-ray fluorescence and LECO Trade-Mark-Sign -CNS method.

  9. Environment sensitive embedding energies of impurities, and grain boundary stability in tantalum

    International Nuclear Information System (INIS)

    Krasko, G.L.

    1996-01-01

    Metalloid impurities have a very low solubility in tantalum, and therefore prefer to segregate at the grain boundaries (GBs). In order to analyze the energetics of the impurities on the tantalum GB, the LMTO calculations were performed on a simple 8-atom supercell emulating a typical (capped trigonal prism) GB environment. The so-called environment-sensitive embedding energies were calculated for hydrogen, boron, carbon, nitrogen, oxygen, phosphorus, and sulphur, as a function of the electron charge density due to the host atoms at the impurity site. The calculations showed that, at the electron density typical of a GB, carbon has the lowest energy (followed by Nitrogen and Boron) and thus would compete with the other impurities for the site on the GB, tending to displace them from the GB. The above energies were then used in a modified Finnis-Sinclair embedded atom approach for calculating the cohesive energies and the equilibrium interplanar distances in the vicinity of a (111) Σ3 tilt GB plane, both for the clean GB and that with an impurity. These distances were found to oscillate, returning to the value corresponding to the equilibrium spacing between (111) planes in bulk BCC tantalum by the 10th--12th plane off the GB. Carbon, nitrogen and boron somewhat dampen the deformation wave (making the oscillations less than in the clean GB), while oxygen, phosphorus and sulphur result in an increase of the oscillations. The cohesive energies follow the same trend, the GB with carbon being the most stable. Thus, carbon, nitrogen and boron may be thought of as being cohesion enhancers, while oxygen, phosphorus and sulphur result in decohesion effects

  10. Qualitative scale for estimating sulphur dioxide air pollution in England and Wales using epiphytic lichens

    Energy Technology Data Exchange (ETDEWEB)

    Hawksworth, D L; Rose, F

    1970-01-01

    The sulphur dioxide in the air can be estimated qualitatively by studying the lichens growing on trees. A ten-point scale has been constructed and used in pilot surveys in England and Wales, Southeast England and the city of Leicester.

  11. Respiratory effects of sulphur dioxide : a hierarchical multicity analysis in the APHEA 2 study

    NARCIS (Netherlands)

    Sunyer, J; Atkinson, R; Ballester, F; Le Tertre, A; Ayres, JG; Forastiere, F; Forsberg, B; Vonk, JM; Bisanti, L; Anderson, RH; Schwartz, J; Katsouyanni, K

    Background: Sulphur dioxide (SO2) was associated with hospital admissions for asthma in children in the original APHEA study, but not with other respiratory admissions. Aims: To assess the association between daily levels of SO2 and daily levels of respiratory admissions in a larger and more recent

  12. High energy physics advisory panel's subpanel on vision for the future of high-energy physics

    International Nuclear Information System (INIS)

    1994-05-01

    This report was requested by the Secretary of Energy to (1) define a long-term program for pursuing the most important high-energy physics goals since the termination of the Superconducting Super Collider (SSC) project, (2) assess the current US high-energy physics program, and (3) make recommendations regarding the future of the field. Subjects on which recommendations were sought and which the report addresses were: high-energy physics funding priorities; facilitating international collaboration for future construction of large high-energy physics facilities; optimizing uses of the investment made in the SSC; how to encourage displaced scientists and engineers to remain in high-energy physics and to attract young scientists to enter the field in the future. The report includes a description of the state of high-energy physics research in the context of history, a summary of the SSC project, and documentation of the report's own origins and development

  13. Bromine monoxide / sulphur dioxide ratios in relation to volcanological observations at Mt. Etna 2006–2009

    Directory of Open Access Journals (Sweden)

    G. Giuffrida

    2012-12-01

    Full Text Available Over a 3-yr period, from 2006 to 2009, frequent scattered sunlight DOAS measurements were conducted at Mt. Etna at a distance of around 6 km downwind from the summit craters. During the same period and in addition to these measurements, volcanic observations were made by regularly visiting various parts of Mt. Etna. Here, results from these measurements and observations are presented and their relation is discussed. The focus of the investigation is the bromine monoxide/sulphur dioxide (BrO / SO2 ratio, and its variability in relation to volcanic processes. That the halogen/sulphur ratio can serve as a precursor or indicator for the onset of eruptive activity was already proposed by earlier works (e.g. Noguchi and Kamiya 1963; Menyailov, 1975; Pennisi and Cloarec, 1998; Aiuppa et al., 2002. However, there is still a limited understanding today because of the complexity with which halogens are released, depending on magma composition and degassing conditions. Our understanding of these processes is far from complete, for example of the rate and mechanism of bubble nucleation, growth and ascent in silicate melts (Carroll and Holloway, 1994, the halogen vapour-melt partitioning and the volatile diffusivity in the melt (Aiuppa et al., 2009. With this study we aim to add one more piece to the puzzle of what halogen/sulphur ratios might tell about volcanic activities. Our data set shows an increase of the BrO / SO2 ratio several weeks prior to an eruption, followed by a decline before and during the initial phase of eruptive activities. Towards the end of activity or shortly thereafter, the ratio increases to baseline values again and remains more or less constant during quiet phases. To explain the observed evolution of the BrO / SO2 ratio, a first empirical model is proposed. This model suggests that bromine, unlike chlorine and fluorine, is less soluble in the magmatic melt than sulphur. By using the DOAS method to determine SO2, we actually

  14. Modification of the sulphur resistance of platinum by addition of metals for aromatics hydrogenation; Modification de la thioresistance du platine par ajouts d'elements metalliques pour l'hydrogenation d'aromatiques

    Energy Technology Data Exchange (ETDEWEB)

    Guillon, E

    1999-09-15

    The aim of this study is based on the understanding of sulphur resistance of platinum catalytic systems. In this work, bimetallic systems (Pt-Ge, Pt-Au and Pt-Pd) supported on {gamma}-alumina have been studied. Preparation methods have been chosen to give the best control of the physicochemical properties of final system. Electronic and geometrical properties of the metallic phase were characterised by various techniques (TPR, infrared spectroscopy of adsorbed CO (IR(CO)), EXAFS, LEIS). Ortho-xylene hydrogenation in presence of 100 ppm of sulphur was used as model catalytic test in order to study the sulphur resistance of the catalysts. It has been shown that germanium and palladium act as electro-acceptors toward platinum. The ranking of catalytic activity in presence of sulphur is as followed: Pt-Pd > Pt-Au {approx_equal} Pt >> Pt-Ge {approx_equal} 0. The best sulphur resistance for Pt-Pd was obtained for the composition Pt{sub 20}Pd{sub 80} (Pd/Pt=4). An eggshell PdS structure with Pt (sulfur free) core is proposed. These works show that the sulphur resistance of platinum is not only linked with its electronic properties. They allow us to propose an original concept of sulphur resistant catalyst taking into account each catalytic parameters such as chemical bonding of S and aromatic compounds on the metallic site, physico-chemical characteristics of the bimetallic aggregates (particle size, structure, surface composition) and electronic modification of surface atoms in bimetallic catalysts. (author)

  15. Resonance-enhanced multiphoton ionization photoelectron spectroscopy of even-parity autoionizing Rydberg states of atomic sulphur

    NARCIS (Netherlands)

    Woutersen, S.; de Milan, J.B.; de Lange, C.A.; Buma, W.J.

    1997-01-01

    Several previously unobserved Rydberg states of the sulphur atom above the lowest ionization threshold are identified and assigned using (2 + 1) resonance-enhanced multiphoton-ionization photoelectron spectroscopy. All states were accessed by two-photon transitions from either the 3P ground or the

  16. Hair analysis as a useful procedure for detection of vapour exposure to chemical warfare agents: simulation of sulphur mustard with methyl salicylate.

    Science.gov (United States)

    Spiandore, Marie; Piram, Anne; Lacoste, Alexandre; Josse, Denis; Doumenq, Pierre

    2014-06-01

    Chemical warfare agents (CWA) are highly toxic compounds which have been produced to kill or hurt people during conflicts or terrorist attacks. Despite the fact that their use is strictly prohibited according to international convention, populations' exposure still recently occurred. Development of markers of exposure to CWA is necessary to distinguish exposed victims from unexposed ones. We present the first study of hair usage as passive sampler to assess contamination by chemicals in vapour form. This work presents more particularly the hair adsorption capacity for methyl salicylate used as a surrogate of the vesicant sulphur mustard. Chemical vapours toxicity through the respiratory route has historically been defined through Haber's law's concentration-time (Ct) product, and vapour exposure of hair to methyl salicylate was conducted with various times or doses of exposure in the range of incapacitating and lethal Ct products corresponding to sulphur mustard. Following exposure, extraction of methyl salicylate from hair was conducted by simple soaking in dichloromethane. Methyl salicylate could be detected on hair for vapour concentration corresponding to about one fifth of the sulphur mustard concentration that would kill 50% of exposed individuals (LCt50). The amount of methyl salicylate recovered from hair increased with time or dose of exposure. It showed a good correlation with the concentration-time product, suggesting that hair could be used like a passive sampler to assess vapour exposure to chemical compounds. It introduces great perspectives concerning the use of hair as a marker of exposure to CWA. Copyright © 2014 John Wiley & Sons, Ltd.

  17. Sulphur self as a bioindicator of air pollution

    International Nuclear Information System (INIS)

    Sihelska, N.; Semerad, M.; Cernansky, S.; Ruzickova, J.; Takacova, A.

    2015-01-01

    Road transport is one of the major sources of air polluting emissions. An average passenger car produces emissions of 228 g/km, trucks produce emissions of around 317 g/km. Emissions from combustion engines contain carbon dioxide, water vapour, nitrogen oxides, ammonia, carbon monoxide, unburned hydrocarbons, sulphur dioxide and various solids. Emissions also contain compounds of toxic metals/metalloids - arsenic, cadmium, chrome, nickel and lead. To detect metal/metalloid contamination from vehicle emissions, samples were collected and analyzed from biomass and soil near Bratislava's busiest road. We focused our attention on concentration of metals/metalloids in Laetiporus sulphureus because it's a very popular edible mushroom. Mushrooms are very good proxies for the state of nearby environment because of their excellent accumulation ability. (authors)

  18. Carbon- versus sulphur-based zinc binding groups for carbonic anhydrase inhibitors?

    Science.gov (United States)

    Supuran, Claudiu T

    2018-12-01

    A set of compounds incorporating carbon-based zinc-binding groups (ZBGs), of the type PhX (X = COOH, CONH 2 , CONHNH 2 , CONHOH, CONHOMe), and the corresponding derivatives with sulphur(VI)-based ZBGs (X = SO 3 H, SO 2 NH 2 , SO 2 NHNH 2 , SO 2 NHOH, SO 2 NHOMe) were tested as inhibitors of all mammalian isoforms of carbonic anhydrase (CA, EC 4.2.1.1), CA I-XV. Three factors connected with the ZBG influenced the efficacy as CA inhibitor (CAI) of the investigated compounds: (i) the pKa of the ZBG; (ii) its geometry (tetrahedral, i.e. sulphur-based, versus trigonal, i.e. carbon-based ZBGs), and (iii) orientation of the organic scaffold induced by the nature of the ZBG. Benzenesulphonamide was the best inhibitor of all isoforms, but other ZBGs led to interesting inhibition profiles, although with an efficacy generally reduced when compared to the sulphonamide. The nature of the ZBG also influenced the CA inhibition mechanism. Most of these derivatives were zinc binders, but some of them (sulfonates, carboxylates) may interact with the enzyme by anchoring to the zinc-coordinated water molecule or by other inhibition mechanisms (occlusion of the active site entrance, out of the active site binding, etc.). Exploring structurally diverse ZBGs may lead to interesting new developments in the field of CAIs.

  19. Molecular indicators for palaeoenvironmental change in a Messinian evaporitic sequence (Vena del Gesso, Italy). II: High-resolution variations in abundances and 13C contents of free and sulphur-bound carbon skeletons in a single marl bed

    Science.gov (United States)

    Kenig, F.; Damste, J. S.; Frewin, N. L.; Hayes, J. M.; De Leeuw, J. W.

    1995-01-01

    The extractable organic matter of 10 immature samples from a marl bed of one evaporitic cycle of the Vena del Gesso sediments (Gessoso-solfifera Fm., Messinian, Italy) was analyzed quantitatively for free hydrocarbons and organic sulphur compounds. Nickel boride was used as a desulphurizing agent to recover sulphur-bound lipids from the polar and asphaltene fractions. Carbon isotopic compositions (delta vs PDB) of free hydrocarbons and of S-bound hydrocarbons were also measured. Relationships between these carbon skeletons, precursor biolipids, and the organisms producing them could then be examined. Concentrations of S-bound lipids and free hydrocarbons and their delta values were plotted vs depth in the marl bed and the profiles were interpreted in terms of variations in source organisms, 13 C contents of the carbon source, and environmentally induced changes in isotopic fractionation. The overall range of delta values measured was 24.7%, from -11.6% for a component derived from green sulphur bacteria (Chlorobiaceae) to -36.3% for a lipid derived from purple sulphur bacteria (Chromatiaceae). Deconvolution of mixtures of components deriving from multiple sources (green and purple sulphur bacteria, coccolithophorids, microalgae and higher plants) was sometimes possible because both quantitative and isotopic data were available and because either the free or S-bound pool sometimes appeared to contain material from a single source. Several free n-alkanes and S-bound lipids appeared to be specific products of upper-water-column primary producers (i.e. algae and cyanobacteria). Others derived from anaerobic photoautotrophs and from heterotrophic protozoa (ciliates), which apparently fed partly on Chlorobiaceae. Four groups of n-alkanes produced by algae or cyanobacteria were also recognized based on systematic variations of abundance and isotopic composition with depth. For hydrocarbons probably derived from microalgae, isotopic variations are well correlated with

  20. Density and energy of supernova remnants

    Energy Technology Data Exchange (ETDEWEB)

    Canto, J [Manchester Univ. (UK). Dept. of Astronomy

    1977-12-01

    The effects of an interstellar magnetic field on the gas flow behind a strong shock front are considered. The ambient density and energy of supernova remnants are estimated from the intensity ratio of sulphur lines I(6717)/I(6731). It is found that, on average, the ambient density around galactic supernova remnants is 4 cm/sup -3/. The total energy appears to be the same for all supernova remnants (to within a factor = approximately 5). A mean value of 4 10/sup 51/ erg is found.

  1. The X-ray fluorescent method for determination of total sulphur in bituminous coals

    International Nuclear Information System (INIS)

    Widowska-Kusmierska, J.; Siess, K.

    1979-01-01

    The X-ray fluorescent technique for the determination of total sulphur covering concentrations from 0,1 to 10% has been applied for bituminous coals showing a great variability in qualitative and quantitative composition of mineral matter (ash). The described method is a quick one giving results during one hour. The obtained good accuracy of determinations gives prospects for wide industrial application. (author)

  2. Impact of dia- and catagenesis on sulphur and oxygen sequestration of biomarkers as revealed by artificial maturation of an immature sedimentary rock

    Science.gov (United States)

    Koopmans, M.P.; De Leeuw, J. W.; Lewan, M.D.; Sinninghe, Damste J.S.

    1996-01-01

    Hydrous pyrolysis of an immature (R(a)??? 0.25%) sulphur-rich marl from the Gessoso-solfifera Formation (Messinian) in the Vena del Gesso Basin was carried out at 160C ??? T ???330 C for 72 h, to study the effect of progressive diagenesis and early catagenesis on the abundance and distribution of sulphur-containing and sulphur- and oxygen-linked carbon skeletons in low-molecular-weight and highmolecular-weight fractions (e.g. kerogen). To this end, compounds in the saturated hydrocarbon fraction, monoaromatic hydrocarbon fraction, polyaromatic hydrocarbon fraction, alkylsulphide fraction and ketone fraction were quantified, as well as compounds released after desulphurisation of the polar fraction and HI/LiAIH4 treatment of the desulphurised polar fraction. Sulphur-bound phytane and (20R)-5??,14??,17??(H) and (20R)-5??,14??,17??(H) C27 C29 steranes in the polar fraction become less abundant with increasing maturation temperature, whereas the amount of their corresponding hydrocarbons increases in the saturated hydrocarbon fraction. Carbon skeletons that are bound in the kerogen by multiple bonds (e.g. C38 n-alkane and isorenieratane) are first released into the polar fraction, and then as free hydrocarbons. These changes occur at relatively low levels of thermal maturity (R(a) <0.6%), as evidenced by the 'immature' values of biomarker maturity parameters such as the ????/(????+ ???? + ????) C35 hopane ratio and the 22S/(22S + 22R)-17??,21??(H) C35 hopane ratio. Sulphur- and oxygen-bound moieties, present in the polar fraction, are not stable with increasing thermal maturation. However, alkylthiophenes, ketones. 1,2-di-n-alkylbenzenes and free n-alkanes seem to be stable thermal degradation products of these sulphur- and oxygen-bound moieties. Thus, apart from free n-alkanes, which are abundantly present in more mature sedimentary rocks and crude oils, alkylthiophenes, 1,2-di-n-alkylbenzenes and ketones can also be expected to occur. The positions of the thiophene

  3. Performance Recognition for Sulphur Flotation Process Based on Froth Texture Unit Distribution

    Directory of Open Access Journals (Sweden)

    Mingfang He

    2013-01-01

    Full Text Available As an important indicator of flotation performance, froth texture is believed to be related to operational condition in sulphur flotation process. A novel fault detection method based on froth texture unit distribution (TUD is proposed to recognize the fault condition of sulphur flotation in real time. The froth texture unit number is calculated based on texture spectrum, and the probability density function (PDF of froth texture unit number is defined as texture unit distribution, which can describe the actual textual feature more accurately than the grey level dependence matrix approach. As the type of the froth TUD is unknown, a nonparametric kernel estimation method based on the fixed kernel basis is proposed, which can overcome the difficulty when comparing different TUDs under various conditions is impossible using the traditional varying kernel basis. Through transforming nonparametric description into dynamic kernel weight vectors, a principle component analysis (PCA model is established to reduce the dimensionality of the vectors. Then a threshold criterion determined by the TQ statistic based on the PCA model is proposed to realize the performance recognition. The industrial application results show that the accurate performance recognition of froth flotation can be achieved by using the proposed method.

  4. A novel approach to mitigating sulphur dioxide emissions and producing a mercury sorbent material using oil-sands fluid coke

    International Nuclear Information System (INIS)

    Morris, E.; Jia, C.Q.; Tong, S.

    2008-01-01

    Pyrometallurgical smelting operations are a major source of sulphur dioxide (SO 2 ) which is a precursor to acid rain and increased levels of UV-B penetration in boreal lakes. Mercury is also released in copper smelter off-gas, which can bioaccumulate and cause neurological disorders and death in humans. Fluid coke is produced in massive quantities as a by-product of bitumen upgrading at Syncrude Canada's facility in Fort McMurray, Alberta. Oilsands fluid coke can be used to reduce SO 2 and produce elemental sulphur as a co-product. This process was dubbed SOactive. The reaction physically activates the fluid coke to produce a sulphur-impregnated activated carbon (SIAC) which is known as ECOcarbon. Some studies have indicated that SIAC is well suited for the removal of vapour phase mercury, mainly due to the formation of stable mercuric sulphide species. This paper discussed the findings made to date in relation to the SOactive process and the characterization of ECOcarbons. The paper discussed the use of fluid coke for reducing SO 2 emissions while producing elemental sulphur as well as coke-SO 2 -oxygen (O 2 ) and coke-SO 2 -water (H 2 O) systems. The paper also examined the production of SIAC products for use in capturing vapour phase mercury. The paper presented the materials and methodology, including an illustration of the apparatus used in reduction of SO 2 and activation of fluid coke. It was concluded that more work is still needed to analyse the effect of O 2 and SO 2 reduction and SIAC properties under smelter flue gas conditions. 10 refs., 1 tab., 8 figs

  5. Comparison between two plant nitrogen and sulphur determination methods: impact on wheat sulphur diagnostics Comparación de métodos de determinación de nitrógeno y azufre en planta: implicancia en el diagnóstico de azufre en trigo

    Directory of Open Access Journals (Sweden)

    Nahuel I Reussi Calvo

    2008-12-01

    Full Text Available The nitrogen and sulphur ratio (N:S in plants is often used as a sulphur diagnostics tool in wheat. This ratio requires two different analyses results for its calculation, and thus involves two sources of analytical error. The objective of this work was to compare the accuracy and reliability of the Dumas dry combustion method for N and S determination in plant, compared to traditional methods of wet digestion, and its use as a sulphur diagnostics tool in wheat. The N and S determination was carried out in wheat plant samples from four experiments carried out in the 2006 growing season in the southwestern Buenos Aires province. A highly significant correlation was obtained between both methods (r = 0.99 and r = 0.74 for N and S, respectively. The quantity of N recuperated by the Dumas method was not significantly different to the Kjeldahl method, however, the reliability of the former was higher (low variability coefficient. The method of turbidimetry with wet digestion underestimated (20% the sulphur concentration compared to the Dumas method. Moreover, the sulphur percent recovered from standard samples was 83 % and 96 % for the turbidimetry and Dumas methods, respectively. The underestimation of plant sulphur concentration by the turbidimetry method resulted in a low percentage of samples correctly diagnosed (25, 18.7 and 50% for Z22, Z24 and Z31, respectively. However, the percent of samples correctly diagnosed was high by the Dumas method (94, 94 and 100% for Z22, Z24 and Z31, respectively. The results of this work indicate that the reliability of the N:S ratio is limited by the S analysis accuracy. On the other hand, the N recovery for both methods was similar.La relación nitrógeno (N: azufre (S total es utilizada frecuentemente para el diagnóstico de deficiencias de S en trigo. Para determinar este índice es necesario la realización de dos análisis diferentes, y por lo tanto, es afectada por dos errores analíticos. El objetivo fue

  6. 30 CFR 256.52 - Bond requirements for an oil and gas or sulphur lease.

    Science.gov (United States)

    2010-07-01

    ... included in the Gulf of Mexico. Areawide bonds issued in the Gulf of Mexico will cover oil and gas or sulphur operations offshore the Atlantic Coast. The three areas are: (1) The Gulf of Mexico and the area... Treasury securities under this paragraph (f), you must monitor their value. If their market value falls...

  7. Dosimetry of high energy radiation

    CERN Document Server

    Sahare, P D

    2018-01-01

    High energy radiation is hazardous to living beings and a threat to mankind. The correct estimation of the high energy radiation is a must and a single technique may not be very successful. The process of estimating the dose (the absorbed energy that could cause damages) is called dosimetry. This book covers the basic technical knowledge in the field of radiation dosimetry. It also makes readers aware of the dangers and hazards of high energy radiation.

  8. Charged kaon and pion production at midrapidity in proton nucleus and sulphur nucleus collisions

    CERN Document Server

    Boggild, H.; Dodd, J.; Esumi, S.; Fabjan, C.W.; Fields, D.E.; Franz, A.; Hansen, K.H.; Humanic, T.J.; Jacak, B.V.; Kalechofsky, H.; Lee, Y.Y.; Leltchouk, M.; Lorstad, B.; Maeda, N.; Miyabayashi, A.; Murray, M.; Nishimura, S.; Pandey, S.U.; Piuz, F.; Polychronakos, V.; Potekhin, M.; Poulard, G.; Sakaguchi, A.; Sarabura, M.; Simon-Gillo, J.; Schmidt-Sorensen, J.; Sondheim, W.; Sugitate, T.; Sullivan, J.P.; Sumi, Y.; van Hecke, H.; Willis, W.J.; Wolf, K.

    1999-01-01

    The NA44 collaboration has measured charged kaon and pion distributions at midrapidity in sulphur and proton collisions with nuclear targets at 200 and 450 GeV/c per nucleon, respectively. The inverse slopes of kaons are larger than those of pions. The difference in the inverse slopes of pions, kaons and protons, all measured in our spectrometer, increases with system size and is consistent with the buildup of collective flow for larger systems. The target dependence of both the yields and inverse slopes is stronger for the sulphur beam suggesting the increased importance of secondary rescattering for SA reactions. The rapidity density, dN/dy, of both K+ and K- increases more rapidly with system size than for pi+ in a similar rapidity region. This trend continues with increasing centrality, and according to RQMD, it is caused by secondary reactions between mesons and baryons. The K-/K+ ratio falls with increasing system size but more slowly than the pbar/p ratio. The pi-/pi+ ratio is close to unity for all sy...

  9. High energy physics advisory panel`s subpanel on vision for the future of high-energy physics

    Energy Technology Data Exchange (ETDEWEB)

    1994-05-01

    This report was requested by the Secretary of Energy to (1) define a long-term program for pursuing the most important high-energy physics goals since the termination of the Superconducting Super Collider (SSC) project, (2) assess the current US high-energy physics program, and (3) make recommendations regarding the future of the field. Subjects on which recommendations were sought and which the report addresses were: high-energy physics funding priorities; facilitating international collaboration for future construction of large high-energy physics facilities; optimizing uses of the investment made in the SSC; how to encourage displaced scientists and engineers to remain in high-energy physics and to attract young scientists to enter the field in the future. The report includes a description of the state of high-energy physics research in the context of history, a summary of the SSC project, and documentation of the report`s own origins and development.

  10. High energy hadron scattering

    International Nuclear Information System (INIS)

    Johnson, R.C.

    1980-01-01

    High energy and small momentum transfer 2 'yields' 2 hadronic scattering processes are described in the physical framework of particle exchange. Particle production in high energy collisions is considered with emphasis on the features of inclusive reactions though with some remarks on exclusive processes. (U.K.)

  11. High- and middle-energy geothermics

    International Nuclear Information System (INIS)

    Anon.

    1995-01-01

    High and middle energy geothermal resources correspond to temperature intervals of 220-350 C and 90-180 C, respectively, and are both exploited for electricity production. Exploitation techniques and applications of high and of middle energy geothermics are different. High energy geothermics is encountered in active volcanic and tectonic zones, such as the circum-Pacific fire-belt, the lesser Antilles, the peri-Mediterranean Alpine chain or the African rift zone. The geothermal steam is directly expanded in a turbine protected against gas and minerals corrosion. About 350 high energy plants are distributed in more than 20 different countries and represent 6000 M We. The cost of high energy installed geothermal kWh ranges from 0.20 to 0.50 French Francs. Middle energy geothermics is encountered in sedimentary basins (between 2000 and 4000 m of depth), in localized fractured zones or at lower depth in the high energy geothermal fields. Heat exchangers with organic fluid Rankine cycle technology is used to produce electricity. Unit power of middle energy plants generally ranges from few hundreds of k W to few MW and correspond to a worldwide installed power of about 400 M We. The annual progression of geothermal installed power is estimated to 4 to 8 % in the next years and concerns principally the circum-Pacific countries. In France, geothermal resources are mainly localized in overseas departments. (J.S.). 3 photos

  12. Superconducting magnets in high energy physics

    International Nuclear Information System (INIS)

    Prodell, A.G.

    1978-01-01

    The applications of superconducting magnets in high energy physics in the last ten years have made feasible developments which are vital to high energy research. These developments include high magnetic field, large volume detectors, such as bubble chambers, required for effective resolution of high energy particle trajectories, particle beam transport magnets, and superconducting focusing and bending magnets for the very high energy accelerators and storage rings needed to pursue the study of interactions between elementary particles. The acceptance of superconductivity as a proven technology in high energy physics was reinforced by the recognition that the existing large accelerators using copper-iron magnets had reached practical limits in terms of magnetic field intensity, cost, space, and energy usage, and that large-volume, high-field, copper-iron magnets were not economically feasible. Some of the superconducting magnets and associated systems being used in and being developed for high energy physics are described

  13. Major changes in forest carbon and nitrogen cycling caused by declining sulphur deposition

    Czech Academy of Sciences Publication Activity Database

    Oulehle, F.; Evans, C. D.; Hofmeister, J.; Krejci, R.; Tahovská, K.; Persson, T.; Cudlín, Pavel; Hruška, J.

    2011-01-01

    Roč. 17, č. 10 (2011), 3115–3129 ISSN 1354-1013 R&D Projects: GA MŠk OC10022 Institutional research plan: CEZ:AV0Z60870520 Keywords : acidification * carbon * deposition * DOC * forest floor * leaching * nitrogen * nitrogen saturation * soil * sulphur Subject RIV: DD - Geochemistry Impact factor: 6.862, year: 2011 http://onlinelibrary.wiley.com/doi/10.1111/j.1365-2486.2011.02468.x/pdf

  14. High energy colliders

    International Nuclear Information System (INIS)

    Palmer, R.B.; Gallardo, J.C.

    1997-02-01

    The authors consider the high energy physics advantages, disadvantages and luminosity requirements of hadron (pp, p anti p), lepton (e + e - , μ + μ - ) and photon-photon colliders. Technical problems in obtaining increased energy in each type of machine are presented. The machines relative size are also discussed

  15. High Average Power, High Energy Short Pulse Fiber Laser System

    Energy Technology Data Exchange (ETDEWEB)

    Messerly, M J

    2007-11-13

    Recently continuous wave fiber laser systems with output powers in excess of 500W with good beam quality have been demonstrated [1]. High energy, ultrafast, chirped pulsed fiber laser systems have achieved record output energies of 1mJ [2]. However, these high-energy systems have not been scaled beyond a few watts of average output power. Fiber laser systems are attractive for many applications because they offer the promise of high efficiency, compact, robust systems that are turn key. Applications such as cutting, drilling and materials processing, front end systems for high energy pulsed lasers (such as petawatts) and laser based sources of high spatial coherence, high flux x-rays all require high energy short pulses and two of the three of these applications also require high average power. The challenge in creating a high energy chirped pulse fiber laser system is to find a way to scale the output energy while avoiding nonlinear effects and maintaining good beam quality in the amplifier fiber. To this end, our 3-year LDRD program sought to demonstrate a high energy, high average power fiber laser system. This work included exploring designs of large mode area optical fiber amplifiers for high energy systems as well as understanding the issues associated chirped pulse amplification in optical fiber amplifier systems.

  16. Energy dependence of ulrathin LiF-dosemeters for high energy electrons and high energy X-radiation

    International Nuclear Information System (INIS)

    Kupfer, T.

    1977-02-01

    The energy dependence of ultrathin LiF-dosemeters for high energy electrons (5-40 MeV) and high energy X-radiation (6 MV, 42 MV) is experimentally determined. The experimental values are compared to values calculted earlier by other authors. The influence of the thickness of the dosemeters have been considered by comparison of experimental values for 0.03 mm thick dosemeters and theoretical values for 0.13 mm and 0.38 mm thick ones. Also different commersially available dosemeters have been compared by experiments. It is difficult to draw any other conclutions about the energy dependence than that the variation of the relative responce is within +- 3 percent (2S). However the results seems to be sulficient for clinical applications

  17. The heat source of Ruapehu crater lake; deductions from the energy and mass balances

    Science.gov (United States)

    Hurst, A. W.; Bibby, H. M.; Scott, B. J.; McGuinness, M. J.

    1991-05-01

    Regular observations of temperature, outflow rates and water chemistry of Crater Lake, Mt. Ruapehu, New Zealand have been made for the last 25 years. These data have been used to derive a model of the dynamics of the lake, and determine the input of energy, mass, and chloride from the volcano to the Crater Lake. The recent, relatively quiescent state of the volcano, when virtually no heat has been input to the lake, has also enabled an assessment to be made of the surface heat loss characteristics, which play an important role in the model of the lake. The modelling suggests that since about 1982 the ratio of the volcanic heat to mass added to the base of the lake is about 6 MJ/kg, which is not compatible with heating of the lake by magmatic steam alone. Thus, only about 50% of the heating has been by magmatic steam. It is suggested that heat could be transferred from a magmatic source to the region below the lake by a heat-pipe mechanism, commonly associated with geothermal systems. The simultaneous upward movement of vapour phase, and downward movement of liquid phase from condensed vapour allows efficient heat transfer without overall mass transfer. The permeability necessary to supply the required heat is of the order of 10 darcy, and is consistent with a rubble filled vent. For at least the last five years, there has been a characteristic pattern in the Crater Lake temperature record, with alternate heating and cooling phases. The heating phase generally lasts for one or two months, while the cooling phase lasts for six months to a year. A possible explanation for this cyclic behaviour is the presence of a layer of liquid sulphur under Crater Lake, acting as a partial barrier between the heat-pipe and the lake. The unusual variations of the viscosity of liquid sulphur with temperature will mean that at temperatures greater than 160°C, the layer of sulphur becomes highly viscous and would block any upwards steam flow and hence stop the heat input to Crater

  18. The isotopic composition and content of sulphur in soils of Kansk-Achinsk fuel power generation complex

    International Nuclear Information System (INIS)

    Grinenko, L.N.; Grinenko, V.A.

    1991-01-01

    In the 1970s the first phase of a large coal-burning power complex was brought into operation in the Kansk-Achinsk region of the Soviet Union. The target consumption for this complex is 50 x 10 6 tonnes yr -1 and most of this is supplied from local open-pit mines. The emission of SO 2 from this plant caused concern as to its impact on the local environment and prompted a study of the sulphurous depositions. Monitoring the areal extent and distribution of the deposited S and its fate in the environment can be a mammoth task involving continual measurement of many biological and physical factors including atmospheric concentrations, wind speed, emission rates, and forms of S in soil, plants, and animals. A possible alternative for evaluating the amount, distribution, and fate of the emitted S in the ecosystem is stable sulphur isotope analyses since different coals and SO 2 from their combustion often have δ 34 S values differing from those of soils and plants in the region. The study reported here was initiated to see if the δ 34 S values for emissions differed significantly from the natural environment. Assuming that the difference was sufficient, a second objective was to document changes that have occurred in the sulphur isotope compositions of the environmental receptors over time. Soil samples from 23 sites were collected and analysed for S content and δ 34 S values. Coal, cinder and ash collected from furnaces and SO 2 from the combustion products were similarly analysed. Figs and tabs

  19. Probable damage to tundra biota through sulphur dioxide destruction of lichens

    Energy Technology Data Exchange (ETDEWEB)

    Schofield, E; Hamilton, W L

    1970-01-01

    Lichens, which are important components of many Arctic ecosystems, are extremely sensitive to SO/sub 2/ pollution. Recent oilfield development in Arctic North America seems likely to eliminate lichens from large areas because of a unique combination of biological and meteorological factors. Probable future oilfield development in Greenland and the Soviet Union indicates that SO/sub 2/ pollution will become an increasingly serious threat to Arctic ecosystems. Therefore, uncontrolled burning of crude oil, fuel oil, and natural gas, should be avoided, and adequate sulphur-extraction facilities should be installed.

  20. Response of fodder legumes berseem (trifolium alexandrinum, L) shaftal (trifolium resupinatum L) and lucerne (medicago sative, L) to sulphur fertilization for nodulatin, forage yield and nitrogen fixation

    International Nuclear Information System (INIS)

    Idris, M.; Zeb, A.; Iqbal, M.M.

    2001-01-01

    The effect of sulphur fertilization (10, 20 mg/kg soil) applied as ground elemental sulphur (98% S) on the forage yield and biological nitrogen fixation of three fodder legumes (Lucerne, Shaftal and Berseem) was studied under pot culture condition. Basal dozes of nitrogen (N), phosphorus (P/sub 2/O/sub 5) and potash (K/sub 2/O) at 10, 40, 20 mg /kg soil were applied to each pot. The result revealed that the application of sulphur did not cause any significant improvement in the nontidal response of Lucerne, Shaftal and berseem. Dry matter yield of forage in four cuts, however was improved significantly in the range of 16.0 to 57.0% for Lucerne, 9.0 to 53.0% for shaftal and 15.0 to 81.0% for berseem by sulphur fertilizations. Biological nitrogen fixation in shoots as revealed by shoot N yield difference exhibited a significant increase by 20.0 to 62.0% for Lucerne, 13.0 to 59.0% for shaftal and 25.0 to 89.0% for berseem in 4 cuts, while in roots biological nitrogen fixation exhibited a significant increase by 5.0 to 25.0% for Lucerne, 11.0 to 41.0 percent for shaftal and 21.0 to 38.0 percent for berseem as result of sulphur fertilization. (author)

  1. The high energy galaxy

    International Nuclear Information System (INIS)

    Cesarsky, C.J.

    1986-08-01

    The galaxy is host to a wide variety of high energy events. I review here recent results on large scale galactic phenomena: cosmic-ray origin and confinement, the connexion to ultra high energy gamma-ray emission from X-ray binaries, gamma ray and synchrotron emission in interstellar space, galactic soft and hard X-ray emission

  2. Consequences of the Swedish energy policy

    International Nuclear Information System (INIS)

    Almstroem, P.

    2000-01-01

    Sweden is unique among the industrialised nations of the world to be affected by a decision that puts its whole future and welfare at risk. The parliamentary decision on energy policy made in spring 1997, is considered a highly unfortunate one. The decision to start a premature phasing-out of nuclear power is especially serious. In order to transform Sweden into an ecological model country, the 'transition program' was launched by the Government. It proposed investments in reducing the electricity consumption and research and development of new energy technology renewable energy sources which produced no results. It is also important to reconsider the environmental consequences of the closure of Barsebaeck NPP. A comparison of emissions in Sweden and Denmark, which has no NPPs reveals that Denmark emits 10 times more carbon dioxide and 20 times more sulphur dioxide and nitrogen oxides. The renewable energy sources will become commercially competitive in the future, but meanwhile the Kyoto objective can be reached only by continuing to use nuclear power as long as it is commercially competitive and as long as there are no other ecologically sustainable systems

  3. The recovery of uranium, gold and sulphur from residues from South African mines

    International Nuclear Information System (INIS)

    Toens, P.D.

    1978-10-01

    The slimes dams resulting from the operations of gold and gold/uranium mines situated within the Witwatersrand Basin contain low concentrations of gold, uranium and pyrite. As a result of a marked increase in the prices of both gold and uranium in recent years, two schemes involving the recovery of these minerals also the manufacture of sulphuric acid as a by-product are operating profitably. Further schemes are under investigation [af

  4. High energy physics and grid computing

    International Nuclear Information System (INIS)

    Yu Chuansong

    2004-01-01

    The status of the new generation computing environment of the high energy physics experiments is introduced briefly in this paper. The development of the high energy physics experiments and the new computing requirements by the experiments are presented. The blueprint of the new generation computing environment of the LHC experiments, the history of the Grid computing, the R and D status of the high energy physics grid computing technology, the network bandwidth needed by the high energy physics grid and its development are described. The grid computing research in Chinese high energy physics community is introduced at last. (authors)

  5. Modification of the sulphur resistance of platinum by addition of metals for aromatics hydrogenation; Modification de la thioresistance du platine par ajouts d'elements metalliques pour l'hydrogenation d'aromatiques

    Energy Technology Data Exchange (ETDEWEB)

    Guillon, E.

    1999-09-15

    The aim of this study is based on the understanding of sulphur resistance of platinum catalytic systems. In this work, bimetallic systems (Pt-Ge, Pt-Au and Pt-Pd) supported on {gamma}-alumina have been studied. Preparation methods have been chosen to give the best control of the physicochemical properties of final system. Electronic and geometrical properties of the metallic phase were characterised by various techniques (TPR, infrared spectroscopy of adsorbed CO (IR(CO)), EXAFS, LEIS). Ortho-xylene hydrogenation in presence of 100 ppm of sulphur was used as model catalytic test in order to study the sulphur resistance of the catalysts. It has been shown that germanium and palladium act as electro-acceptors toward platinum. The ranking of catalytic activity in presence of sulphur is as followed: Pt-Pd > Pt-Au {approx_equal} Pt >> Pt-Ge {approx_equal} 0. The best sulphur resistance for Pt-Pd was obtained for the composition Pt{sub 20}Pd{sub 80} (Pd/Pt=4). An eggshell PdS structure with Pt (sulfur free) core is proposed. These works show that the sulphur resistance of platinum is not only linked with its electronic properties. They allow us to propose an original concept of sulphur resistant catalyst taking into account each catalytic parameters such as chemical bonding of S and aromatic compounds on the metallic site, physico-chemical characteristics of the bimetallic aggregates (particle size, structure, surface composition) and electronic modification of surface atoms in bimetallic catalysts. (author)

  6. Energy spectra and asymmetry of charged particle emission in the muon minus capture by nuclei

    International Nuclear Information System (INIS)

    Balandin, M.P.; Grebenyuk, V.M.; Sinov, V.G.; Konin, A.D.

    1978-01-01

    Energy spectra of separated-by-mass single-charged particles at the capture of 130 MeV negative muons by carbon, oxygen, magnesium and sulphur have been measured. The experimental results are compared with the theoretical calculations at the assumption of preequilibrium decay of collective states described by the hydrodynamical model. The measurement of asymmetry of charged particle emission in sulphur and megnesium was carried out by hte method of muon spin precession in a magnetic field. Theoretical curves describe correctly the exponential spectra character, but the yields obtained are 2-3 times less than the experimental results

  7. The influences of sulphur and phosphorus additions on the creep cavitation characteristics in type 304 stainless steels

    International Nuclear Information System (INIS)

    Jun Hwa Hong; Soo Woo Nam; Sun Pil Choi

    1986-01-01

    The effects of impurities on creep cavitation characteristics in type 304 stainless steels with and without additions of sulphur and/or phosphorus have been studied using four experimental heats. Over a limited range of stress at 1000 K, the change in size distribution of creep cavities and carbide precipitates, and the level of impurity segregation with the amount of addition have been investigated. It is found that phosphorus accelerates the nucleation of creep cavities, but retards the growth of them. However, sulphur had little effect on both nucleation and growth of the cavities. It has also been found that ageing prior to testing inhibits creep cavitation. The effects of impurities on cavitation are analysed and discussed from the viewpoint of the change in the segregation of impurities and the precipitation of carbides due to impurity additions. (author)

  8. Ergo betters estimates after shaky first years. [Recovery of gold, uranium and sulphuric acid

    Energy Technology Data Exchange (ETDEWEB)

    1982-05-20

    Having completed its fourth year of full operation, East Rand Gold and Uranium (ERGO) has established itself as a succesful low-cost gold producer. The recovering of gold, uranium and sulphuric acid from some old slimes dams has beaten its production estimates for 1981 till the end of March 1982. Overall Ergo has settled down well from its first years of production.

  9. Effect of the synthetic zeolite modification on its physicochemical and catalytic properties in the preparation of the catalysts effectively removing sulphur dioxide from exhaust gases

    Directory of Open Access Journals (Sweden)

    Marcewicz-Kuba Agnieszka

    2016-06-01

    Full Text Available This work presents the research results of the influence of modification deSONOx type catalyst of the sulfur dioxide emissions in the process of the hard coal combustion. The addition of zeolite catalysts modified by transition metal ions: V, Mg, activated by zinc sorbent with or without graphite addition caused the deeper burning of coal grains. The addition of the deSOx catalysts to the coal resulted in lowered sulphur dioxide emission. The addition of unmodified zeolite to coal during combustion reduced sulphur dioxide emission at about 5%. The modification of the support by both V and Mg reduced the amount of sulphur dioxide significantly. The obtained results of SO2 removal from exhaust gases were from 34.5% for Sip/Mg to 68.3% for Sip/V.

  10. 发烟硫酸浓度互换公式的推导%Derivation about Concentrations Exchanging Formula of Fuming Sulphuric Acid

    Institute of Scientific and Technical Information of China (English)

    谭靖辉; 唐淑贞

    2011-01-01

    指出发烟硫酸是游离态SO3的H2SO4溶液,运用质量守恒定律对发烟硫酸浓度互换公式进行了推导,阐述了使用该公式的注意事项。%Fuming sulphuric acid was regarded as SO3 of free state in sulfuric acid solution,concentrations exchanging formula of fuming sulphuric acid was deduced by mass conservation law,attentions of formula were expounded.

  11. Future of high energy physics

    International Nuclear Information System (INIS)

    Panofsky, W.K.H.

    1984-06-01

    A rough overview is given of the expectations for the extension of high energy colliders and accelerators into the xtremely high energy range. It appears likely that the SSC or something like it will be the last gasp of the conventional method of producing high energy proton-proton collisions using synchrotron rings with superconducting magnets. It is likely that LEP will be the highest energy e+e - colliding beam storage ring built. The future beyond that depends on the successful demonstrations of new technologies. The linear collider offers hope in this respect for some extension in energy for electrons, and maybe even for protons, but is too early to judge whether, by how much, or when such an extension will indeed take place

  12. The diffusion of sulphur from moulding sand to cast and methods of its elimination

    Directory of Open Access Journals (Sweden)

    M. Hosadyna

    2009-10-01

    Full Text Available The care of high quality castings requires taking into account the possible negative influence of decomposition products of moulding and core sands on the structure of castings produced. Such products are emitted both from the sands of I generation, meaning sands bound by bentonite, especially those containing carbon forming additives, as well as from the sands of II generation, meaning the sands with the binding materials or even the sands without any binders, such as the forms produced by using the LOST FOAM technology. The literature often refers to the negative effects of nitrogen emitted from the sands with the urea resins on the tendency to create surface defects. That is why the aim of this study was to assess the degree of sulphur diffusion to the ferroalloy castings and the proposal of its limitation.

  13. Preliminary model and validation of molten carbonate fuel cell kinetics under sulphur poisoning

    Science.gov (United States)

    Audasso, E.; Nam, S.; Arato, E.; Bosio, B.

    2017-06-01

    MCFC represents an effective technology to deal with CO2 capture and relative applications. If used for these purposes, due to the working conditions and the possible feeding, MCFC must cope with a different number of poisoning gases such as sulphur compounds. In literature, different works deal with the development of kinetic models to describe MCFC performance to help both industrial applications and laboratory simulations. However, in literature attempts to realize a proper model able to consider the effects of poisoning compounds are scarce. The first aim of the present work is to provide a semi-empirical kinetic formulation capable to take into account the effects that sulphur compounds (in particular SO2) have on the MCFC performance. The second aim is to provide a practical example of how to effectively include the poisoning effects in kinetic models to simulate fuel cells performances. To test the reliability of the proposed approach, the obtained formulation is implemented in the kinetic core of the SIMFC (SIMulation of Fuel Cells) code, an MCFC 3D model realized by the Process Engineering Research Team (PERT) of the University of Genova. Validation is performed through data collected at the Korea Institute of Science and Technology in Seoul.

  14. The reducibility of sulphuric acid and sulphate in aqueous solution (translated from German)

    International Nuclear Information System (INIS)

    Grauer, R.

    1990-07-01

    In connection with the Swedish project for the final storage of spent fuel elements it was necessary to assess whether dissolved sulphate can corrode the copper canister without the intervention of sulphate-reducing bacteria. A simple reaction between copper and sulphate is thermodynamically impossible. On the other hand, copper can react to give copper sulphide if an additional electron donor such as iron is available. Because little specific information is available about this subject the problem was extended to the much more general question of the reducibility of sulphur in dilute aqueous solution. It is a part of the general knowledge of chemistry, and there is also unanimity about it in the geochemical literature, that purely chemical reduction of sulphate does not take place in dilute solution at temperatures below 100 degrees C. This fact is, however, poorly documented and it was therefore necessary to substantiate it by drawing on numerous individual findings from different areas of pure and applied chemistry. The investigation confirms that sulphur in dilute solution is completely inert towards chemical reducing agents and also to cathodic reduction. Thus corrosion of copper by sulphate under final-storage conditions and in the absence of sulphate reducing bacteria can be ruled out with a probability verging on certainty. (85 refs.)

  15. Support of the EMEP-project: European wide depositions of sulphur and nitrogen compounds as a consequence of sulphur, nitrogen oxides and ammonia emissions; Unterstuetzung der EMEP-Modellrechnungen: Europaweite Deposition schwefel- und stickstoffhaltiger Verbindungen als Folge der Emissionen von Schwefel, Stickoxiden und Ammoniak

    Energy Technology Data Exchange (ETDEWEB)

    Krueger, O [Hamburg Univ. (Germany). Meteorologisches Inst.; Grassl, H [Hamburg Univ. (Germany). Meteorologisches Inst.

    1994-01-01

    For the European long range transport model EMEP the parametrisations of dry and wet deposition were improved. The dry deposition of sulphur and ammonia was improved in the source grid element with a high resolution Eulerian model. The wet deposition was improved over sea areas. With satellite measurements of the SSM/I it was demonstrated, that a detailed treatment of precipitation processes in the norwegian weather forecast model LAM50 with a prognostic equation for the cloud water content, in contrast to the routine version, provides more realistic precipitation fields for air pollution modelling. The agreement between modelled and observed concentrations of sulphur and nitrogen compounds in air and precipitation is within a range of 40 to 70%. (orig.) [Deutsch] Es wurden beim europaweiten Ausbreitungsmodell EMEP die Parametrisierungen der Trocken- und Nassdeposition verbessert. Bei der Trockendeposition wurde die Ablagerung von Schwefeldioxid und Ammoniak im Quellgitterelement mit einem hochaufloesenden Eulerschen Modell verbessert. Die Nassdeposition wurde ueber Seegebieten verbessert. Es konnte mit Satellitenmessungen des SSM/I nachgewiesen werden, dass sie ausfuehrlichere Behandlung der Niederschlagsprozesse im Norwegischen Wetterdienstmodell LAM50, anders als in seiner Routineversion, mit einer prognostischen Gleichung fuer den Wolkenwassergehalt realistischere Niederschlagshoehen fuer die Stofftransportmodellierung liefert. Vergleiche von Modellrechnungen und Messdaten zeigen fuer Schwefel- und Stickstoffverbindungen fuer Konzentrationen in der Luft und im Niederschlag Abweichungen von 40 bis 70%. (orig.)

  16. A Gas Calorimeter for High-Energy Experiment and Study of High-Energy Cascade Shower

    Energy Technology Data Exchange (ETDEWEB)

    Miyata, Hitoshi [Univ. of Tsukuba (Japan)

    1984-09-01

    High energy behavior of the electromagnetic cascade shower has been studied. high energy showers were created by electron and hadron beams with energies between 25 GeV and 150 GeV at Fermi National Accelerator Laboratory. The showers were observed by a shower detector consisting of multi-layer of lead plates and proportional chambers. The experimental results were analyzed with special emphasis on the fluctuation problem of the electromagnetic cascade shower.

  17. Trend of heavy metal and sulphur deposition in Finland from the 1980`s to 1990`s

    Energy Technology Data Exchange (ETDEWEB)

    Kubin, E.; Lippo, H. [Forest Research Inst., Muhos (Finland)

    1995-12-31

    The moss technique to survey atmospheric heavy metal deposition was developed in Sweden in the late 1960`s. The surveys has extended from regional and national basis to cover all the Nordic countries in 1985, to northern Europe in 1990 and to a large part of Europe in 1990-92. National reports have also been published in many countries. The Forest Research Institute established a network of 3009 secret permanent monitoring sites all over the country in 1985 and 1986 for forest inventory and for monitoring the situation and changes in the forests. One essential part has been to study the effects of air pollution - including heavy metal and sulphur deposition on forests. Deposition has been monitored by collecting bioindicators and analysing the element concentrations. The purpose of this report is to show the trend of the heavy metal and sulphur deposition from the 1980`s to 1990`s and in addition to produce information about the emission sources. (author)

  18. Trend of heavy metal and sulphur deposition in Finland from the 1980`s to 1990`s

    Energy Technology Data Exchange (ETDEWEB)

    Kubin, E; Lippo, H [Forest Research Inst., Muhos (Finland)

    1996-12-31

    The moss technique to survey atmospheric heavy metal deposition was developed in Sweden in the late 1960`s. The surveys has extended from regional and national basis to cover all the Nordic countries in 1985, to northern Europe in 1990 and to a large part of Europe in 1990-92. National reports have also been published in many countries. The Forest Research Institute established a network of 3009 secret permanent monitoring sites all over the country in 1985 and 1986 for forest inventory and for monitoring the situation and changes in the forests. One essential part has been to study the effects of air pollution - including heavy metal and sulphur deposition on forests. Deposition has been monitored by collecting bioindicators and analysing the element concentrations. The purpose of this report is to show the trend of the heavy metal and sulphur deposition from the 1980`s to 1990`s and in addition to produce information about the emission sources. (author)

  19. A Literature Review on the Mechanism of Action of Sulphur and Nitrogen Mustard

    Science.gov (United States)

    1989-07-01

    for years is also poeqible (Aasted et al, 1987; Colardyn et al, 1986). Severely poisoned individuals exhibit bone marrow depression and may die from...MMS does not produce the enhanced depression of DNA synthesis in sensitive cells, compared to resistant cells, produced by sulphur mustard and...Compound MATD 1 Protection (mg/mouse) index 2 WR-3689 15 159 WR-2721 15 44 Aminoethylcysteine 80 27 N- acetylcysteine 8 26 Glutathione 60 22 Cysteine 8

  20. High energy cosmic ray astronomy

    International Nuclear Information System (INIS)

    Fonseca, V.

    1996-01-01

    A brief introduction to High Energy Cosmic Ray Astronomy is presented. This field covers a 17 decade energy range (2.10 4 -10 20 ) eV. Recent discoveries done with gamma-ray detectors on-board satellites and ground-based Cherenkov devices are pushing for a fast development of new and innovative techniques, specially in the low energy region which includes the overlapping of satellite and ground-based measurements in the yet unexplored energy range 20 keV-250 GeV. Detection of unexpected extremely high energy events have triggered the interest of the international scientific community. (orig.)

  1. Energy sector

    International Nuclear Information System (INIS)

    1995-01-01

    Within the framework of assessing the state of the environment in Lebanon, this chapter describes primary energy demand, the electricity generating sector and environmental impacts arising from the energy sector.Apart from hydropower and traditional energy sources, which together represent 1.7% of energy consumption, all energy in Lebanon derives from imported petroleum products and some coal.Tables present the imports of different petroleum products (Gasoil, Kerosene, fuel oil, coal etc...), their use, the energy balance and demand.Energy pricing and pricing policies, formal and informal electricity generations in Lebanon are described emphasized by tables. The main environmental impacts are briefly summarized. Thermal power stations give rise to emissions of Sulphur dioxide (SO 2 ), particulates, oxides of nitrogen (NO x ) and CO/CO 2 from combustion of primary fuel informally generated power from both industry and domestic consumption produce particulate materials and emissions of NO x and SO 2 projected emissions of SO 2 from the power sector with the present generating capacity and with the new combined cycle power plants in operation are shown. Other environmental impacts are described. Recommendations for supply and environment policy are presented

  2. Extraction mechanism of Sc(III) from sulphuric acid solution by primary amine N1923

    International Nuclear Information System (INIS)

    Le Shaoming; Li Deqian; Ni Jiazan

    1987-01-01

    The extraction mechanism of Sc(III) from sulphuric acid solution by primary amine N 1923 (RNH 2 ) has been investigated by means of slope, isomolar continuous variation and saturation methods. The effect of temperature on the extraction of Sc(III) is observed. The extraction equilibrium constant and thermodynamic functions (ΔH, ΔS and ΔG) are obtained. The IR and NMR of extracted compound are measured

  3. The determination of sulphur in copper, nickel and aluminium alloys by proton activation analysis

    International Nuclear Information System (INIS)

    Vandecasteele, C.; Dewaele, J.; Esprit, M.; Goethals, P.

    1981-01-01

    The 34 S(p,n) 34 sup(m)Cl reaction, induced by 13 MeV protons is used for the determination of sulphur in copper, nickel and aluminium alloys. The 34 sup(m)Cl is separated by repeated precipitation as silver chloride. The results obtained were resp. 3.08 +- 0.47, 1.47 +- 0.17 and -1 for copper, nickel and aluminium alloys. (orig.)

  4. High energy dosimetry

    International Nuclear Information System (INIS)

    Ruhm, W.

    2010-01-01

    Full text: Currently, quantification of doses from high-energy radiation fields is a topical issue. This is so because high-energy neutrons play an important role for radiation exposure of air crew members and personnel outside the shielding of ion therapy facilities. In an effort to study air crew exposure from cosmic radiation in detail, two Bonner Sphere Spectrometers (BSSs) have recently been installed to measure secondary neutrons from cosmic radiation, one at the environmental research station 'Schneefernerhaus' at an altitude of 2650 m on the Zugspitze mountain, Germany, the other at the Koldewey station close to the North Pole on Spitsbergen. Based on the measured neutron fluence distributions and on fluence-to-dose conversion coefficients, mean ambient dose equivalent rate values of 75.0 ± 2.9 nSv/h and 8.7 ± 0.6 nSv/h were obtained for October 2008, respectively. Neutrons with energies above about 20 MeV contribute about 50% to dose, at 2650 m. Ambient dose equivalent rates measured by means of a standard rem counter and an extended rem counter at the Schneefernerhaus confirm this result. In order to study the response of state-of-the-art radiation instrumentation in such a high-energy radiation field, a benchmark exercise that included both measurements in and simulation of the stray neutron radiation field at the high-energy particle accelerator at GSI, Germany, were performed. This CONRAD (COordinated Network for RAdiation Dosimetry) project was funded by the European Commission, and the organizational framework was provided by the European Radiation Dosimetry Group, EURADOS. The Monte Carlo simulations of the radiation field and the experimental determination of the neutron spectra with various Bonner Sphere Spectrometers suggest the neutron fluence distributions to be very similar to those of secondary neutrons from cosmic radiation. The results of this intercomparison exercise in terms of ambient dose equivalent are also discussed

  5. Combined experimental and numerical kinetic characterization of NR vulcanized with sulphur, N terbutyl, 2 benzothiazylsulphenamide and N,N diphenyl guanidine

    Energy Technology Data Exchange (ETDEWEB)

    Milani, G., E-mail: gabriele.milani@polimi.it [Politecnico di Milano, Piazza Leonardo da Vinci 32, 20133 Milan (Italy); Hanel, T.; Donetti, R. [Pirelli Tyre, Via Alberto e Piero Pirelli 25, 20126 Milan (Italy); Milani, F. [Chem. Co, Via J.F.Kennedy 2, 45030 Occhiobello (Italy)

    2016-06-08

    The paper presents the final results of a comprehensive experimental and numerical analysis aimed at deeply investigating the behavior of Natural Rubber (NR) vulcanized with sulphur in presence of different accelerators during standard rheometer tests. NR in presence of sulphur and two different accelerators (DPG and TBBS) in various concentrations is investigated, changing the curing temperature in the range 150-180°C and obtaining rheometer curves with a step of 10°C. Sulphur-TBBS concentrations considered are 1-1, 1-3, 3-3 and 3-1, with DPG at 1-4 phr respectively. A total of 48 experimental rheometer curves is so obtained. To fit experimental data, the general reaction scheme proposed by Han and co-workers for vulcanized sulphur NR is re-adapted and suitably modified taking into account the single contributions of the different accelerators. Chain reactions initiated by the formation of macro-compounds responsible for the formation of the unmatured crosslinked polymer are accounted for. In presence of two accelerators, reactions are assumed to proceed in parallel, making the practically effective hypothesis that there is no interaction between the two accelerators. From the simplified kinetic scheme adopted, a closed form solution is found for the crosslink density, with the only limitation that the induction period is excluded from computations. For each experimented case on the same blend, reaction kinetic constants provided by the model are utilized to deduce their trend in the Arrhenius space, also outside the temperature range inspected. Rather close linearity is found in the majority of the cases. A comparative analysis is carefully conducted among the constants at the different concentrations of S, TBBS and DPG investigated, allowing a prediction of curing behavior at any vulcanization temperature and with concentrations not experimentally tested, without the need of addition costly experimentation.

  6. Combined experimental and numerical kinetic characterization of NR vulcanized with sulphur, N terbutyl, 2 benzothiazylsulphenamide and N,N diphenyl guanidine

    International Nuclear Information System (INIS)

    Milani, G.; Hanel, T.; Donetti, R.; Milani, F.

    2016-01-01

    The paper presents the final results of a comprehensive experimental and numerical analysis aimed at deeply investigating the behavior of Natural Rubber (NR) vulcanized with sulphur in presence of different accelerators during standard rheometer tests. NR in presence of sulphur and two different accelerators (DPG and TBBS) in various concentrations is investigated, changing the curing temperature in the range 150-180°C and obtaining rheometer curves with a step of 10°C. Sulphur-TBBS concentrations considered are 1-1, 1-3, 3-3 and 3-1, with DPG at 1-4 phr respectively. A total of 48 experimental rheometer curves is so obtained. To fit experimental data, the general reaction scheme proposed by Han and co-workers for vulcanized sulphur NR is re-adapted and suitably modified taking into account the single contributions of the different accelerators. Chain reactions initiated by the formation of macro-compounds responsible for the formation of the unmatured crosslinked polymer are accounted for. In presence of two accelerators, reactions are assumed to proceed in parallel, making the practically effective hypothesis that there is no interaction between the two accelerators. From the simplified kinetic scheme adopted, a closed form solution is found for the crosslink density, with the only limitation that the induction period is excluded from computations. For each experimented case on the same blend, reaction kinetic constants provided by the model are utilized to deduce their trend in the Arrhenius space, also outside the temperature range inspected. Rather close linearity is found in the majority of the cases. A comparative analysis is carefully conducted among the constants at the different concentrations of S, TBBS and DPG investigated, allowing a prediction of curing behavior at any vulcanization temperature and with concentrations not experimentally tested, without the need of addition costly experimentation.

  7. Gasoline reformulation to reduce exhaust emissions in Finnish conditions. Influence of sulphur and benzene contents of gasoline on exhaust emissions

    International Nuclear Information System (INIS)

    Kytoe, M.; Aakko, P.; Lappi, M.

    1994-01-01

    At earlier stages of the study it was found that the exhaust emissions from cars are reduced when using fuels with no more than 4 wt% of oxygen. At this stage of the study the work focused on impacts of the sulphur and benzene content of gasoline on exhaust emissions in Finland. Sulphur in gasoline retards the operation of the catalyst, and consequently the exhaust emissions of catalyst cars increase if the sulphur content of the fuel increases. In the present study, evaporation during refuelling were measured for fuels with varying vapour pressures and benzene contents of gasoline. The total hydrocarbon evaporation was reduced by 22 % (10 g) when the vapour pressure of gasoline was reduced from 85 kPa to 65 kPa. Correspondingly, benzene evaporation during refuelling was reduced to a third when the benzene content of the fuel was reduced from the level of 3 wt% to 1 wt%. The reduction of the sulphur content of gasoline from 500 ppm to 100 ppm affected regulated exhaust emissions from the catalyst car at +22 deg C as follows: CO emission was reduced on average by 14 % (0.175 g/km), CH emission by 7 % (0.010 g/km) and NO x emission by 9 % (0.011 g/km). At-7 deg C the percentual changes were smaller. When the benzene content of the fuel was reduced from 3 wt% to 1 wt%, the benzene emission from the catalyst cars was reduced by 20-30 % and from the non-catalyst cars on average by 30 % both at +22 deg C and -7 deg C. The benzene emission ranged 3-22 mg/km for the catalyst cars and 40-90 mg/km for the non-catalyst cars at +22 deg C in the FTP test

  8. High voltage tests of an electrostatic accelerator for different mixtures of gases at various pressures

    International Nuclear Information System (INIS)

    Hellborg, R.

    1996-01-01

    An account is given of high voltage tests of an electrostatic accelerator. High voltage conditioning is measured and is reported for the same accelerator tube after different periods of usage. Tests of different mixtures of sulphur hexafluoride and nitrogen have been performed. A considerable amount of data was obtained for various parameters connected with the high voltage system for different proportions of nitrogen in sulphur hexafluoride at various gas pressures. (orig.)

  9. Moderate energy ions for high energy density physics experiments

    International Nuclear Information System (INIS)

    Grisham, L.R.

    2004-01-01

    This paper gives the results of a preliminary exploration of whether moderate energy ions (≅0.3-3 MeV/amu) could be useful as modest-cost drivers for high energy density physics experiments. It is found that if the target thickness is chosen so that the ion beam enters and then leaves the target in the vicinity of the peak of the dE/dX (stopping power) curve, high uniformity of energy deposition may be achievable while also maximizing the amount of energy per beam particle deposited within the target

  10. High energy hadron spin-flip amplitude

    International Nuclear Information System (INIS)

    Selyugin, O.V.

    2016-01-01

    The high-energy part of the hadron spin-flip amplitude is examined in the framework of the new high-energy general structure (HEGS) model of the elastic hadron scattering at high energies. The different forms of the hadron spin-flip amplitude are compared in the impact parameter representation. It is shown that the existing experimental data of the proton-proton and proton-antiproton elastic scattering at high energy in the region of the diffraction minimum and at large momentum transfer give support in the presence of the energy-independent part of the hadron spin-flip amplitude with the momentum dependence proposed in the works by Galynskii-Kuraev. [ru

  11. Ozone and sulphur dioxide effects on leaf water potential of Petunia

    Energy Technology Data Exchange (ETDEWEB)

    Elkiey, T.; Ormrod, D.P.

    1979-01-01

    Three cultivars of Petunia hydrida Vilm., of differing ozone visible injury sensitivity, were exposed to 40 parts per hundred million (pphm) ozone and/or 80 pphm SO/sub 2/ for 4 h to study the relationships of leaf water potential, pollutant exposure, and cultivar sensitivity. Ozone substantially decreased leaf water potential in cv White Cascade but not in cv Capri or White Magic. Sulphur dioxide did not affect leaf water potential but delayed ozone-induced changes. Cultivar sensitivity to ozone-induced changes in leaf water potential was not related to cultivar sensitivity to ozone-induced visible injury.

  12. Computing in high energy physics

    Energy Technology Data Exchange (ETDEWEB)

    Watase, Yoshiyuki

    1991-09-15

    The increasingly important role played by computing and computers in high energy physics is displayed in the 'Computing in High Energy Physics' series of conferences, bringing together experts in different aspects of computing - physicists, computer scientists, and vendors.

  13. Computing in high energy physics

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Sarah; Devenish, Robin [Nuclear Physics Laboratory, Oxford University (United Kingdom)

    1989-07-15

    Computing in high energy physics has changed over the years from being something one did on a slide-rule, through early computers, then a necessary evil to the position today where computers permeate all aspects of the subject from control of the apparatus to theoretical lattice gauge calculations. The state of the art, as well as new trends and hopes, were reflected in this year's 'Computing In High Energy Physics' conference held in the dreamy setting of Oxford's spires. The conference aimed to give a comprehensive overview, entailing a heavy schedule of 35 plenary talks plus 48 contributed papers in two afternoons of parallel sessions. In addition to high energy physics computing, a number of papers were given by experts in computing science, in line with the conference's aim – 'to bring together high energy physicists and computer scientists'.

  14. Effect of vermicomposting on calcium, sulphur and some heavy metal content of different biodegradable organic wastes under liming and microbial inoculation.

    Science.gov (United States)

    Das, Debabrata; Bhattacharyya, Pradip; Ghosh, B C; Banik, Pabitra

    2012-01-01

    A study was conducted to evaluate the changes in total calcium and sulphur and some heavy metal (Zn, Cu, and Pb) concentration of different organic wastes affected by liming and microorganism inoculation. Vermicomposting was an effective technology for disposal of organic substrates like municipal solid wastes (MSW), possessing comparatively higher concentration of heavy metals. The addition of lime in initial organic substrates significantly (P ≤ 0.05) increased total calcium and total sulphur content of vermicomposts. Inoculation of microorganisms significantly (P ≤ 0.05) reduced the heavy metal content of final products as compared to control. Fungal strains were comparatively more effective in detoxification of heavy metals than B. polymyxa.

  15. Computing in high energy physics

    International Nuclear Information System (INIS)

    Watase, Yoshiyuki

    1991-01-01

    The increasingly important role played by computing and computers in high energy physics is displayed in the 'Computing in High Energy Physics' series of conferences, bringing together experts in different aspects of computing - physicists, computer scientists, and vendors

  16. Long-term sedimentary recycling of rare sulphur isotope anomalies.

    Science.gov (United States)

    Reinhard, Christopher T; Planavsky, Noah J; Lyons, Timothy W

    2013-05-02

    The accumulation of substantial quantities of O2 in the atmosphere has come to control the chemistry and ecological structure of Earth's surface. Non-mass-dependent (NMD) sulphur isotope anomalies in the rock record are the central tool used to reconstruct the redox history of the early atmosphere. The generation and initial delivery of these anomalies to marine sediments requires low partial pressures of atmospheric O2 (p(O2); refs 2, 3), and the disappearance of NMD anomalies from the rock record 2.32 billion years ago is thought to have signalled a departure from persistently low atmospheric oxygen levels (less than about 10(-5) times the present atmospheric level) during approximately the first two billion years of Earth's history. Here we present a model study designed to describe the long-term surface recycling of crustal NMD anomalies, and show that the record of this geochemical signal is likely to display a 'crustal memory effect' following increases in atmospheric p(O2) above this threshold. Once NMD anomalies have been buried in the upper crust they are extremely resistant to removal, and can be erased only through successive cycles of weathering, dilution and burial on an oxygenated Earth surface. This recycling results in the residual incorporation of NMD anomalies into the sedimentary record long after synchronous atmospheric generation of the isotopic signal has ceased, with dynamic and measurable signals probably surviving for as long as 10-100 million years subsequent to an increase in atmospheric p(O2) to more than 10(-5) times the present atmospheric level. Our results can reconcile geochemical evidence for oxygen production and transient accumulation with the maintenance of NMD anomalies on the early Earth, and suggest that future work should investigate the notion that temporally continuous generation of new NMD sulphur isotope anomalies in the atmosphere was likely to have ceased long before their ultimate disappearance from the rock record.

  17. High Energy Physics Departments - Overview

    International Nuclear Information System (INIS)

    Bartke, J.

    1999-01-01

    Following the tradition, the activities of the seven new units created in 1997 on the basis of the former Department of High Energy Physics are presented under a common header, they are: Department of Particle Theory (Dept 5); Department of Leptonic Interactions (Dept 11); Department of Hadron Structure (Dept 12); Department of High Energy Nuclear Interactions (Dept 13); The ALICE Experiment Laboratory (NAL); The ATLAS Experiment Laboratory (NAT); High Energy Physics Detector Construction Group (PBD). The research covers a variety of problems of the experimental and theoretical high energy particle physics: the hadronic and leptonic interactions with nucleons and nuclei (characteristics of particle production, including heavy quark physics), e + e - interactions and tests of the Standard Model (also radiative corrections), ultrarelativistic heavy ion interactions and search for the quark-gluon plasma, as well as the spectra, composition and interactions of high energy cosmic ray particles. Research on detectors and accelerator components as well as the development of the apparatus for the high energy physics experiments at future accelerators: LHC (CERN, Geneva), RHIC (Brookhaven), B-Factory (KEK, Tsukuba) and TESLA (DESY) is also presented. The technology of new materials with unique properties such as carbon-carbon composites is also worked on from the point of view of their application in high energy physics experiments. The Division is located in a separate building on the campus of the University of Mining and Metallurgy (UMM). This location, close to the Jagiellonian University (JU), facilitates the collaboration with the latter and with the UMM. The joint weekly seminars carried out for nearly 40 years prove this long term tradition. A substantial part of the activities is teaching and training students from the academic community in Cracow. Joint research, teaching and academic training in the high energy physics are carried out within the M. Miesowicz

  18. Energetic and exergetic life cycle analysis to explain the hidden costs and effects of current sulphur utilisation

    NARCIS (Netherlands)

    Brehmer, B.; Sanders, J.P.M.

    2007-01-01

    Typically life cycle analyses of the fertiliser industry are based on averages of outdated technology. Sulphur is a major element, emerging as a primary nutrient on its own accord and as a feed for other fertiliser production, namely phosphoric acid. Recent developments sparked by governmental

  19. THE EFFECT OF SULPHURIC ACID CONCENTRATION ON SOLVENT EXTRACTION OF ReO4 - BY THE LONG-CHAIN ALIPHATIC TERTIARY AMINES AND ALCOHOLS

    Directory of Open Access Journals (Sweden)

    Aleksander G. Kasikov

    2010-06-01

    Full Text Available The effect of sulphuric acid concentration on solvent extraction of ReO4- by the long-chain aliphatic tertiary amines and alcohols in a wide range of H2SO4 concentrations in initial solutions is discussed. It has been established that the influence of the sulphuric acid concentration on rhenium solvent extraction is largely due to the extraction process mechanism. In the case of the anion-exchange mechanism, ReO4- is best extracted from weakly acidic solutions, whereas when the hydrate-solvate mechanism takes place – from solutions containing 4-7 mole/l H2SO4.

  20. Hydrogen production by the iodine-sulphur thermochemical cycle. Total and partial pressure measurements

    International Nuclear Information System (INIS)

    D Doizi; V Dauvois; J L Roujou; V Delanne; P Fauvet; B Larousse; O Hercher; P Carles; C Moulin

    2006-01-01

    The iodine sulphur thermochemical cycle appears to be one of the most promising candidate for the massive production of hydrogen using nuclear energy. The key step in this cycle is the HI distillation section which must be optimized to get a good efficiency of the overall cycle. The concept of reactive versus extractive distillation of HI has been proposed because of its potentiality. The design and the optimization of the reactive distillation column requires the knowledge of the liquid vapour equilibrium over the ternary HI-I 2 -H 2 O mixtures up to 300 C and 100 bars. A general methodology based on three experimental devices imposed by the very corrosive and concentrated media will be described: 1) I1 for the total pressure measurement versus different ternary compositions. 2) I2 for the partial and total pressure measurements around 130 C and 2 bars to validate the choice of the analytical optical 'online' techniques we have proposed. 3) I3 for the partial and total pressures measurements in the process domain. The results obtained on pure samples, binary mixtures HI-H 2 O and ternary mixtures using an experimental design analysis in the experimental device I2 will be discussed. (authors)