Multicomponent mixed dopant optimization for rapid screening of polycyclic aromatic hydrocarbons using ultra high performance liquid chromatography coupled to atmospheric pressure photoionization high-resolution mass spectrometry

KAUST Repository

Sioud, Salim

2012-05-04

RATIONALE To enhance the ionization efficiencies in atmospheric pressure photoionization mass spectrometry a dopant with favorable ionization energy such as chlorobenzene is typically used. These dopants are typically toxic and difficult to mix with water-soluble organic solvents. In order to achieve a more efficient and less toxic dopant, a multicomponent mixed dopant was explored. METHODS A multicomponent mixed dopant for non-targeted rapid screening of polycyclic aromatic hydrocarbons (PAHs) was developed and optimized using ultra high performance liquid chromatography (UPLC) coupled to atmospheric pressure photoionization high-resolution mass spectrometry. Various single and multicomponent mixed dopants consisting of ethanol, chlorobenzene, bromobenzene, anisole and toluene were evaluated. RESULTS Fourteen out of eighteen PAHs were successfully separated and detected at low pg/μL levels within 5 min with high mass accuracy ≤4 ppm. The optimal mixed multicomponent dopant consisted of ethanol/chlorobenzene/bromobenzene/anisole (98.975:0.1:0.9:0.025, v/v %) and it improved the limit of detection (LOD) by 2- to 10-fold for the tested PAHs compared to those obtained with pure chlorobenzene. CONCLUSIONS A novel multicomponent dopant that contains 99% ethanol and 1% mixture of chlorobenzene, bromobenzene and anisole was found to be an effective dopant mixture to ionize PAHs. The developed UPLC multicomponent dopant assisted atmospheric pressure photoionization high-resolution mass spectrometry offered a rapid non targeted screening method for detecting the PAHs at low pg/;μL levels within a 5 min run time with high mass accuracy a;circ4 ppm. Copyright © 2012 John Wiley & Sons, Ltd.

About influence of buffer porous layers between epitaxial layers of heterostructure on distributions of concentrations of dopants in heterobipolar transistors

Directory of Open Access Journals (Sweden)

E Pankratov

2016-10-01

Full Text Available In this paper we introduce an approach to manufacture a heterobipolar transistors. Framework this approach we consider doping by diffusion or by ion implantation of required parts of a heterostructure with special configuration and optimization of annealing of dopant and/or radiation defects. In this case one have possibility to manufacture bipolar transistors, which include into itself p-n-junctions with higher sharpness and smaller dimensions. We also consider influence of presents of buffer porous layers between epitaxial layers of heterostructure on distributions of concentrations of dopants in the considered transistors. An approach to decrease value of mismatch-induced stress has been considered.

Effect of oxygen vacancy and dopant concentration on the magnetic properties of high spin Co2+ doped TiO2 nanoparticles

International Nuclear Information System (INIS)

Choudhury, B.; Choudhury, A.; Maidul Islam, A.K.M.; Alagarsamy, P.; Mukherjee, M.

2011-01-01

Co doped TiO 2 nanoparticles have been synthesized by a simple sol-gel route taking 7.5, 9.5 and 10.5 mol% of cobalt concentration. Formation of nanoparticles is confirmed by XRD and TEM. Increase in d-spacing occurs for (0 0 4) and (2 0 0) peak with increase in impurity content. Valence states of Co and its presence in the doped material is confirmed by XPS and EDX. The entire vacuum annealed samples show weak ferromagnetism. Increased magnetization is found for 9.5 mol% but this value again decreases for 10.5 mol% due to antiferromagnetic interactions. A blocking temperature of 37.9 K is obtained, which shows shifting to high temperature as the dopant concentration is increased. The air annealed sample shows only paramagnetic behavior. Temperature dependent magnetic measurements for the air annealed sample shows antiferromagnetic behavior with a Curie-Weiss temperature of -16 K. Here we report that oxygen vacancy and cobalt aggregates are a key factor for inducing ferromagnetism-superparamagnetism in the vacuum annealed sample. Appearance of negative Curie-Weiss temperature reveals the presence of antiferromagnetic Co 3 O 4 , which is the oxidation result of metallic Co or cobalt clusters present on the host TiO 2 . - Research highlights: → Oxygen vacancy induces ferromagnetism in cobalt doped anatase TiO2 nanoparticles. → On air annealing the sample loses ferromagnetism giving rise to paramagnetism. → Saturation magnetization decreases at higher doping concentration. → Blocking of magnetic moment occurs due to the presence of cobalt clusters.

Direct observation of dopant distribution in GaAs compound semiconductors using phase-shifting electron holography and Lorentz microscopy.

Science.gov (United States)

Sasaki, Hirokazu; Otomo, Shinya; Minato, Ryuichiro; Yamamoto, Kazuo; Hirayama, Tsukasa

2014-06-01

Phase-shifting electron holography and Lorentz microscopy were used to map dopant distributions in GaAs compound semiconductors with step-like dopant concentration. Transmission electron microscope specimens were prepared using a triple beam focused ion beam (FIB) system, which combines a Ga ion beam, a scanning electron microscope, and an Ar ion beam to remove the FIB damaged layers. The p-n junctions were clearly observed in both under-focused and over-focused Lorentz microscopy images. A phase image was obtained by using a phase-shifting reconstruction method to simultaneously achieve high sensitivity and high spatial resolution. Differences in dopant concentrations between 1 × 10(19) cm(-3) and 1 × 10(18) cm(-3) regions were clearly observed by using phase-shifting electron holography. We also interpreted phase profiles quantitatively by considering inactive layers induced by ion implantation during the FIB process. The thickness of an inactive layer at different dopant concentration area can be measured from the phase image. © The Author 2014. Published by Oxford University Press on behalf of The Japanese Society of Microscopy. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Tuning Nanocrystal Surface Depletion by Controlling Dopant Distribution as a Route Toward Enhanced Film Conductivity

Science.gov (United States)

Staller, Corey M.; Robinson, Zachary L.; Agrawal, Ankit; Gibbs, Stephen L.; Greenberg, Benjamin L.; Lounis, Sebastien D.; Kortshagen, Uwe R.; Milliron, Delia J.

2018-05-01

Electron conduction through bare metal oxide nanocrystal (NC) films is hindered by surface depletion regions resulting from the presence of surface states. We control the radial dopant distribution in tin-doped indium oxide (ITO) NCs as a means to manipulate the NC depletion width. We find in films of ITO NCs of equal overall dopant concentration that those with dopant-enriched surfaces show decreased depletion width and increased conductivity. Variable temperature conductivity data shows electron localization length increases and associated depletion width decreases monotonically with increased density of dopants near the NC surface. We calculate band profiles for NCs of differing radial dopant distributions and, in agreement with variable temperature conductivity fits, find NCs with dopant-enriched surfaces have narrower depletion widths and longer localization lengths than those with dopant-enriched cores. Following amelioration of NC surface depletion by atomic layer deposition of alumina, all films of equal overall dopant concentration have similar conductivity. Variable temperature conductivity measurements on alumina-capped films indicate all films behave as granular metals. Herein, we conclude that dopant-enriched surfaces decrease the near-surface depletion region, which directly increases the electron localization length and conductivity of NC films.

Diffusion of ion-implanted B in high concentration P- and As-doped silicon

International Nuclear Information System (INIS)

Fair, R.B.; Pappas, P.N.

1975-01-01

The diffusion of ion-implanted B in Si in the presence of a uniform background of high concentration P or As was studied by correlating numerical profile calculations with profiles determined by secondary-ion mass spectrometry (SIMS). Retarded B diffusion is observed in both As- and P-doped Si, consistent with the effect of the local Fermi-level position in the Si band gap on B diffusivity, D/sub B/. It is shown that D/sub B/ is linearly dependent on the free hole concentration, p, over the range 0.1 less than p/n/sub ie/ less than 30, where n/sub ie/ is the effective intrinsic electron concentration. This result does not depend on the way in which the background dopant has been introduced (implantation predeposition or doped-oxide source), nor the type of dopant used (P or As). (U.S.)

Deprotonation effect of tetrahydrofuran-2-carbonitrile buffer gas dopant in ion mobility spectrometry.

Science.gov (United States)

Fernandez-Maestre, Roberto; Meza-Morelos, Dairo; Wu, Ching

2016-06-15

When dopants are introduced into the buffer gas of an ion mobility spectrometer, spectra are simplified due to charge competition. We used electrospray ionization to inject tetrahydrofuran-2-carbonitrile (F, 2-furonitrile or 2-furancarbonitrile) as a buffer gas dopant into an ion mobility spectrometer coupled to a quadrupole mass spectrometer. Density functional theory was used for theoretical calculations of dopant-ion interaction energies and proton affinities, using the hybrid functional X3LYP/6-311++(d,p) with the Gaussian 09 program that accounts for the basis set superposition error; analytes structures and theoretical calculations with Gaussian were used to explain the behavior of the analytes upon interaction with F. When F was used as a dopant at concentrations below 1.5 mmol m(-3) in the buffer gas, ions were not observed for α-amino acids due to charge competition with the dopant; this deprotonation capability arises from the production of a dimer with a high formation energy that stabilized the positive charge and created steric hindrance that deterred the equilibrium with analyte ions. F could not completely strip other compounds of their charge because they either showed steric hindrance at the charge site that deterred the approach of the dopant (2,4-lutidine, and DTBP), formed intramolecular bonds that stabilized the positive charge (atenolol), had high proton affinity (2,4-lutidine, DTBP, valinol and atenolol), or were inherently ionic (tetraalkylammonium ions). This selective deprotonation suggests the use of F to simplify spectra of complex mixtures in ion mobility and mass spectrometry in metabolomics, proteomics and other studies that generate complex spectra with thousands of peaks. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

High-resolution three-dimensional mapping of semiconductor dopant potentials

DEFF Research Database (Denmark)

Twitchett, AC; Yates, TJV; Newcomb, SB

2007-01-01

Semiconductor device structures are becoming increasingly three-dimensional at the nanometer scale. A key issue that must be addressed to enable future device development is the three-dimensional mapping of dopant distributions, ideally under "working conditions". Here we demonstrate how a combin......Semiconductor device structures are becoming increasingly three-dimensional at the nanometer scale. A key issue that must be addressed to enable future device development is the three-dimensional mapping of dopant distributions, ideally under "working conditions". Here we demonstrate how...... a combination of electron holography and electron tomography can be used to determine quantitatively the three-dimensional electrostatic potential in an electrically biased semiconductor device with nanometer spatial resolution....

The use of isoprene as a novel dopant in negative ion atmospheric pressure photoionization mass spectrometry coupled to high-performance liquid chromatography.

Science.gov (United States)

Dousty, Faezeh; O'Brien, Rob

2015-06-15

As in the case with positive ion atmospheric pressure photoionization (PI-APPI), the addition of dopants significantly improves the sensitivity of negative ion APPI (NI-APPI). However, the research on dopant-assisted-NI-APPI has been quite limited compared to the studies on dopant-assisted PI-APPI. This work presents the potential of isoprene as a novel dopant for NI-APPI. Thirteen compounds, possessing suitable gas-phase ion energetic properties in order to make stable negative ions, were selected. Dopants were continuously introduced into a tee junction prior to the ion source through a fused-silica capillary, while analytes were directly injected into the same tee. Then both were mixed with the continuous solvent from high-performance liquid chromatography (HPLC), nebulized, and entered the source. The nebulized stream was analyzed by APPI tandem quadrupole mass spectrometry in the negative ion mode. The results obtained using isoprene were compared with those obtained by using toluene as a dopant and dopant-free NI-APPI. Isoprene enhanced the ionization intensities of the studied compounds, which were found to be comparable and, in some cases, more effective than toluene. The mechanisms leading to the observed set of negative analyte ions were also discussed. Because in NI-APPI, thermal electrons, which are produced during the photoionization of a dopant, are considered the main reagent ions, both isoprene and toluene promoted the ionization of analytes through the same mechanisms, as expected. Isoprene was shown to perform well as a novel dopant for NI-APPI. Isoprene has a high photoabsorption cross section in the VUV region; therefore, its photoionization leads to a highly effective production of thermal electrons, which further promotes the ionization of analytes. In addition, isoprene is environmentally benign and less toxic compared to currently used dopants. Copyright © 2015 John Wiley & Sons, Ltd.

Two-dimensional dopant profiling for shallow junctions by TEM and AFM

International Nuclear Information System (INIS)

Yoo, K.

2000-01-01

The present work concerns the development of the Etch/TEM and Etch/AFM methods to obtain quantitative 2-D dopant profiles for the ultra shallow p-n junctions of the next generation of metal-oxide-semiconductor field effect transistors (MOSFETs). For these methods, thin foil (TEM) or bulk (AFM) cross-sectional specimens were etched using a dopant selective chemical so that local areas of the dopant implanted source/drain (S/D) regions were etched to different depths. The surface topography of the S/D regions was determined from the thickness fringes for the TEM method and by the direct measurement for the AFM method. The local etched depths were converted to etch rates, and these were then converted to corresponding 1-D and 2-D dopant profiles by the experimentally independent etch rate calibration curves. Shallow junction MOSFET samples were designed and fabricated with junction depths 60nm (n + /p), 80nm (n + /p) and 120nm (p + /n) using 0.25μm process technology. A new method using SOG (Spin-on-Glass) contributed to the high quality XTEM thin foil specimens. Controlled stirring of the etchant increased the dopant concentration selectivity and etching consistency. Computer modelling simulated the isotropic etching behaviours, which can introduce the significant error in dopant profiling for shallow and abrupt junction samples. Comprehensive quantitative results enabled the optimum etching time to be determined for the first time. Etch/TEM method gave 1-D dopant profiles that showed good agreement with 1-D Spreading Resistance Probe (SRP) dopant profiles for determining junction depths. 2-D dopant profiles gave L eff , i.e. the shortest lateral distance between the S/D junctions, of major importance for MOSFET performance. Values for L eff of 161, 159 and 123nm were determined from 60, 80 and 120nm junction depth samples respectively, compared with the 215nm MOSFET gate length. The resolution and accuracy of the Etch/TEM method are estimated as 2 and 10nm

Extended OLED operational lifetime through phosphorescent dopant profile management

Science.gov (United States)

Forrest, Stephen R.; Zhang, Yifan

2017-05-30

This disclosure relates, at least in part, an organic light emitting device, which in some embodiments comprises an anode; a cathode; a first emissive layer disposed between the anode and the cathode, the first emissive layer comprising an electron transporting compound and a phosphorescent emissive dopant compound; and wherein the phosphorescent emissive dopant compound has a concentration gradient, in the emissive layer, which varies from the cathode side of the first emissive layer to the anode side of the emissive layer.

Effect of Cu-Dopant on the Structural, Magnetic and Electrical Properties of ZnO

Science.gov (United States)

Aryanto, D.; Kurniawan, C.; Subhan, A.; Sudiro, T.; Sebayang, P.; Ginting, M.; Siregar, S. M. K.; Nasruddin, M. N.

2017-05-01

Zn1- x Cu x O (x = 0, 2, 3, and 4 at.%) was synthesized by using solid-state reaction technique. The ZnO and CuO powders were mixed and then milled by using high-speed shaker mill. The influence of Cu dopants on the structure, magnetic, and electrical properties was investigated by using XRD, VSM, and I-V and C-V measurements. The XRD analysis showed that the Zn1- x Cu x O had hexagonal wurtzite polycrystalline. The diffraction intensity decreased and the peak position shifted directly to a higher 2θ angle with increasing the dopant concentration. Furthermore, the lattice parameters decreased when the ZnO was doped with x = 0.04, which indicated that the crystal structure changed. The increase of Cu dopants was believed to affect the magnetic and electrical properties of ZnO.

Industrially feasible, dopant-free, carrier-selective contacts for high-efficiency silicon solar cells

KAUST Repository

Yang, Xinbo

2017-05-31

Dopant-free, carrier-selective contacts (CSCs) on high efficiency silicon solar cells combine ease of deposition with potential optical benefits. Electron-selective titanium dioxide (TiO) contacts, one of the most promising dopant-free CSC technologies, have been successfully implemented into silicon solar cells with an efficiency over 21%. Here, we report further progress of TiO contacts for silicon solar cells and present an assessment of their industrial feasibility. With improved TiO contact quality and cell processing, a remarkable efficiency of 22.1% has been achieved using an n-type silicon solar cell featuring a full-area TiO contact. Next, we demonstrate the compatibility of TiO contacts with an industrial contact-firing process, its low performance sensitivity to the wafer resistivity, its applicability to ultrathin substrates as well as its long-term stability. Our findings underscore the great appeal of TiO contacts for industrial implementation with their combination of high efficiency with robust fabrication at low cost.

Dopant density from maximum-minimum capacitance ratio of implanted MOS structures

International Nuclear Information System (INIS)

Brews, J.R.

1982-01-01

For uniformly doped structures, the ratio of the maximum to the minimum high frequency capacitance determines the dopant ion density per unit volume. Here it is shown that for implanted structures this 'max-min' dopant density estimate depends upon the dose and depth of the implant through the first moment of the depleted portion of the implant. A a result, the 'max-min' estimate of dopant ion density reflects neither the surface dopant density nor the average of the dopant density over the depletion layer. In particular, it is not clear how this dopant ion density estimate is related to the flatband capacitance. (author)

P2 Asymmetry of Au's M-band Flux and its smoothing effect due to high-Z ablator dopants

Science.gov (United States)

Li, Yongsheng; Zhai, Chuanlei; Ren, Guoli; Gu, Jianfa; Huo, Wenyi; Meng, Xujun; Ye, Wenhua; Lan, Ke; Zhang, Weiyan

2017-10-01

X-ray drive asymmetry is one of the main seeds of low-mode implosion asymmetry that blocks further improvement of the nuclear performance of ``high-foot'' experiments on the National Ignition Facility. More particularly, the P2 asymmetry of Au's M-band flux can also severely influence the implosion performance. Here we study the smoothing effect of mid- and/or high-Z dopants in ablator on M-band flux asymmetries, by modeling and comparing the implosion processes of a Ge-doped and a Si-doped ignition capsule driven by x-ray sources with asymmetric M-band flux. As the results, (1) mid- or high-Z dopants absorb M-band flux and re-emit isotropically, helping to smooth M-band flux arriving at the ablation front, therefore reducing the P2 asymmetries of the imploding shell and hot spot; (2) the smoothing effect of Ge-dopant is more remarkable than Si-dopant due to its higher opacity than the latter in Au's M-band; and (3) placing the doped layer at a larger radius in ablator is more efficient. Applying this effect may not be a main measure to reduce the low-mode implosion asymmetry, but might be of significance in some critical situations such as Inertial Confinement Fusion (ICF) experiments very near the performance cliffs of asymmetric x-ray drives.

Variation of thermophysical parameters of PCM CaCl2.6H2O with dopant from T-history data analysis

Science.gov (United States)

Sutjahja, I. M.; Silalahi, Alfriska O.; Sukmawati, Nissa; Kurnia, D.; Wonorahardjo, S.

2018-03-01

T-history is a powerful method for deriving the thermophysical parameters of a phase change material (PCM), which consists of solid and liquid specific heats as well as latent heat enthalpy. The performance of a PCM for thermal energy storage could be altered by chemical dopants added directly to the PCM in order to form a stable suspension. We described in this paper the role of chemical dopants in the variation of thermophysical parameters for CaCl2 · 6H2O inorganic PCM with 1 wt% and 2 wt% dopant concentration and BaSO4 (1 wt%) as a nucleator using the T-history method. The dopant consists graphite and CuO nanoparticles. The data analysis follows the original method proposed by (Zhang et al 1999 Meas. Sci. Technol. 10 201–205) and its modification by (Hong et al 2004 Int. J. Refrig. 27 360–366). In addition, the enthalpy-temperature curve is obtained by adopting a method proposed by (Marín et al 2003 Meas. Sci. Technol. 14 184–189). We found that the solid specific heat tends to increase non-linearly with increased dopant concentration for all dopants. The increased liquid specific heat, however, indicates the optimum value for 1 wt% graphite dopant. In contrast, the CuO dopant shows a smaller increase in dopant concentration. The specific heat data are analyzed based on the interacting mesolayer model for a nanofluid. The heat of fusion show strong variation with dopant type, in agreement with other experimental data for various PCMs and dopant particles.

Predicting Low Energy Dopant Implant Profiles in Semiconductors using Molecular Dynamics

Energy Technology Data Exchange (ETDEWEB)

Beardmore, K.M.; Gronbech-Jensen, N.

1999-05-02

The authors present a highly efficient molecular dynamics scheme for calculating dopant density profiles in group-IV alloy, and III-V zinc blende structure materials. Their scheme incorporates several necessary methods for reducing computational overhead, plus a rare event algorithm to give statistical accuracy over several orders of magnitude change in the dopant concentration. The code uses a molecular dynamics (MD) model to describe ion-target interactions. Atomic interactions are described by a combination of 'many-body' and pair specific screened Coulomb potentials. Accumulative damage is accounted for using a Kinchin-Pease type model, inelastic energy loss is represented by a Firsov expression, and electronic stopping is described by a modified Brandt-Kitagawa model which contains a single adjustable ion-target dependent parameter. Thus, the program is easily extensible beyond a given validation range, and is therefore truly predictive over a wide range of implant energies and angles. The scheme is especially suited for calculating profiles due to low energy and to situations where a predictive capability is required with the minimum of experimental validation. They give examples of using the code to calculate concentration profiles and 2D 'point response' profiles of dopants in crystalline silicon and gallium-arsenide. Here they can predict the experimental profile over five orders of magnitude for <100> and <110> channeling and for non-channeling implants at energies up to hundreds of keV.

Boron, arsenic and phosphorus dopant incorporation during low temperature low pressure silicon epitaxial growth

International Nuclear Information System (INIS)

Borland, J.O.; Thompson, T.; Tagle, V.; Benzing, W.

1987-01-01

Submicron silicon epitaxial structures with very abrupt epi/substrate transition widths have been realized through the use of low temperature silicon epitaxial growth techniques. At these low temperature and low pressure epitaxial growth conditions there is minimal, if any, dopant diffusion from the substrate into the epilayer during deposition. The reincorporation of autodoped dopant as well as the incorporation of intentional dopant can be a trade-off at low temperatures and low pressures. For advanced CMOS and Bi-CMOS technologies, five to six orders of magnitude change in concentration levels are desirable. In this investigation, all of the epitaxial depositions were carried out in an AMC-7810 epi-reactor with standard jets for a turbulent mixing system, and using a modified center inject configuration to achieve a single pass laminar flow system. To simulate the reincorporation of various autodoped dopant, the authors ran a controlled dopant flow of 100 sccm for each of the three dopants (boron, phosphorus and arsenic) to achieve the controlled background dopant level in the reactor gas stream

Prospects for photosensitive dopants in liquid argon

International Nuclear Information System (INIS)

Anderson, D.F.

1990-12-01

Evidence is presented that the addition of a few ppM of a photosensitive dopant to a U/liquid argon or Pb/liquid argon calorimeter will make a substantial reduction in the e/π ratio. Previous results indicating high voltage problems and no change in the e/π ratio in tests of photosensitive dopants with the Fermilab D0 experiment's U/liquid argon tests calorimeter are also explained. 13 refs., 3 figs

High-performance germanium n+/p junction by nickel-induced dopant activation of implanted phosphorus at low temperature

International Nuclear Information System (INIS)

Huang Wei; Lu Chao; Yu Jue; Wei Jiang-Bin; Chen Chao-Wen; Wang Jian-Yuan; Xu Jian-Fang; Li Cheng; Chen Song-Yan; Lai Hong-Kai; Wang Chen; Liu Chun-Li

2016-01-01

High-performance Ge n + /p junctions were fabricated at a low formation temperature from 325 °C to 400 °C with a metal(nickel)-induced dopant activation technique. The obtained NiGe electroded Ge n + /p junction has a rectification ratio of 5.6× 10 4 and a forward current of 387 A/cm 2 at −1 V bias. The Ni-based metal-induced dopant activation technique is expected to meet the requirement of the shallow junction of Ge MOSFET. (paper)

Analysis of the dopant distribution in Co-deposited organic thin films by scanning transmission electron microscopy

International Nuclear Information System (INIS)

Paredes, Yolanda A.; Campos, Andrea P.C.; Achete, Carlos A.; Cremona, Marco

2015-01-01

Organic light-emitting diodes using phosphorescent dyes (PHOLEDs) have excellent performance, with internal quantum efficiencies approaching 100%. To maximize their performance, PHOLED devices use a conductive organic host material with a sufficiently dispersed phosphorescent guest to avoid concentration quenching. Fac-tris(2-phenylpyridine) iridium, [Ir(ppy)_3] is one of the most widely used green phosphorescent organic compounds. In this work, we used scanning transmission electron microscopy (STEM) equipped with HAADF (high-angle annular dark-field) and EDS (energy dispersive X-ray spectroscopy) detectors to analyze the distribution of the [Ir(ppy)_3] concentration in the host material. This analysis technique, employed for the first time in co-deposited organic thin films, can simultaneously obtain an image and its respective chemical information, allowing for definitive characterization of the distribution and morphology of [Ir(ppy)_3]. The technique was also used to analyze the effect of the vibration of the substrate during thermal co-deposition of the [Ir(ppy)_3] molecules into an organic matrix. - Highlights: • We present a methodology to analyze the dopant distribution in organic thin films. • The method combines HAADF-STEM imaging and EDS X-ray spectroscopy. • Ir(ppy)_3 dopant was co-deposited into Spiro2-CBP organic matrix. • The dopant was co-deposited with and without substrate vibration. • Images and chemical information of the dopant were simultaneously obtained.

PIXE channeling for concentration and location measurements of Zn- and Cd-dopants in InP single crystals

International Nuclear Information System (INIS)

Vogt, J.; Krause, H.; Flagmeyer, R.; Otto, G.; Lux, M.

1993-01-01

We present results of the determination of Cd- and Zn-dopants in InP single crystals using the PIXE and RBS spectrometry at our 2 MeV Van de Graaff accelerator. The (100) oriented crystals were doped by thermodiffusion of Cd and Zn atoms. For concentration and localization measurements we used the ion-channeling technique and energy dispersive spectrometry of proton induced X-ray emission (PIXE). Angular scans of the K-lines of In, Cd and Zn were obtained. The strong In X-rays were attenuated by a rhodium foil in front of the low energy Ge detector. The PIXE-channeling results were compared with SIMS and Hall-effect measurements. (orig.)

Improvement of efficiency roll-off in blue phosphorescence OLED using double dopants emissive layer

Energy Technology Data Exchange (ETDEWEB)

Yoo, Seung Il; Yoon, Ju An; Kim, Nam Ho; Kim, Jin Wook; Kang, Jin Sung; Moon, Chang-Bum [Department of Green Energy & Semiconductor Engineering, Hoseo University, Asan (Korea, Republic of); Kim, Woo Young, E-mail: wykim@hoseo.edu [Department of Green Energy & Semiconductor Engineering, Hoseo University, Asan (Korea, Republic of); Department of Engineering Physics, McMaster University, Hamilton, Ontario L8S 4L7 (Canada)

2015-04-15

Blue phosphorescent organic light-emitting diodes (PHOLEDs) were fabricated using double dopants FIrpic and FIr6 in emissive layer (EML) with structure of ITO/NPB (700 Å)/mCP:FIrpic-8%:FIr6-x% (300 Å)/TPBi (300 Å)/Liq (20 Å)/Al (1200 Å). We optimized concentration of the second dopant FIr6 in the presence of a fixed FIrpic to observe its effect on electrical performance of PHOLED device. 24.8 cd/A of luminous efficiency was achieved by the device with dopant ratio of 8%FIrpic:4%FIr6 in EML. Efficiency roll-off was also improved 20% compared to the PHOLED device singly dopped with FIrpic or FIr6 only. Second doping proved its effect in stabilizing charge balance in EML and enhancing energy transfer of triplet excitons between two dopants. - Highlights: • We fabricated blue PHOLED with double blue phosphorescent dopants in single EML. • Efficiency roll-off was improved by using double dopant in single EML. • The host–dopant transfer is discussed by analyzing the photo-absorption and photoluminescence. • The spectroscopic analysis using multi-peak fits with a Gaussian function.

P2 asymmetry of Au's M-band flux and its smoothing effect due to high-Z ablator dopants

Directory of Open Access Journals (Sweden)

Yongsheng Li

2017-03-01

Full Text Available X-ray drive asymmetry is one of the main seeds of low-mode implosion asymmetry that blocks further improvement of the nuclear performance of “high-foot” experiments on the National Ignition Facility [Miller et al., Nucl. Fusion 44, S228 (2004]. More particularly, the P2 asymmetry of Au's M-band flux can also severely influence the implosion performance of ignition capsules [Li et al., Phys. Plasmas 23, 072705 (2016]. Here we study the smoothing effect of mid- and/or high-Z dopants in ablator on Au's M-band flux asymmetries, by modeling and comparing the implosion processes of a Ge-doped ignition capsule and a Si-doped one driven by X-ray sources with P2 M-band flux asymmetry. As the results, (1 mid- or high-Z dopants absorb hard X-rays (M-band flux and re-emit isotropically, which helps to smooth the asymmetric M-band flux arriving at the ablation front, therefore reducing the P2 asymmetries of the imploding shell and hot spot; (2 the smoothing effect of Ge-dopant is more remarkable than Si-dopant because its opacity in Au's M-band is higher than the latter's; and (3 placing the doped layer at a larger radius in ablator is more efficient. Applying this effect may not be a main measure to reduce the low-mode implosion asymmetry, but might be of significance in some critical situations such as inertial confinement fusion (ICF experiments very near the performance cliffs of asymmetric X-ray drives.

Dopant concentration dependent magnetism of Cu-doped TiO{sub 2} nanocrystals

Energy Technology Data Exchange (ETDEWEB)

Anitha, B.; Khadar, M. Abdul, E-mail: mabdulkhadar@rediffmail.com [University of Kerala, Centre for Nanoscience and Nanotechnology (India)

2016-06-15

Undoped and Cu-doped nanocrystals of TiO{sub 2} having the size range of 8–11 nm were synthesized by peroxide gel method. XRD analysis using Rietveld refinement confirmed anatase phase with a small percentage of rutile content for undoped TiO{sub 2} nanocrystals while a pure anatase phase with preferential growth along [004] direction was observed for nanocrystals of Cu-doped TiO{sub 2}. Variation in the intensity ratios of the XRD peaks of the doped samples compared to that of the undoped sample offered an evidence for the substitutional incorporation of Cu ions in the TiO{sub 2} lattice. The preferential growth of the nanocrystals along the [004] direction was verified using HRTEM analysis. Cu doping extended the optical absorption edge of TiO{sub 2} nanocrystals to the visible spectral region and caused a blue shift and broadening of the E{sub g} (1) Raman active mode of anatase TiO{sub 2}. Undoped TiO{sub 2} sample showed a weak ferromagnetism superimposed on a diamagnetic background while Cu-doped TiO{sub 2} samples exhibited a weak ferromagnetism in the low-field region with a paramagnetic component in the high-field region. The magnetic moment exhibited by the doped samples is interpreted as the resultant of a weak ferromagnetic moment in the low-field region arising from the presence of defects near the surface of TiO{sub 2} nanoparticles or from the interaction of the substituted Cu ions with the oxygen vacancies, and the paramagnetic contribution from the increased Cu dopant concentration near the surface of the particles arising from self-purification mechanism.

Analysis of the dopant distribution in Co-deposited organic thin films by scanning transmission electron microscopy

Energy Technology Data Exchange (ETDEWEB)

Paredes, Yolanda A. [Center of Nanotechnology and Nanoscience, Universidad de las Fuerzas Armadas ESPE, Sangolqui 171-5-31B (Ecuador); Campos, Andrea P.C.; Achete, Carlos A. [DIMAT—INMETRO, Xerém, Duque de Caxias, RJ 25250-020 (Brazil); Cremona, Marco [DIMAT—INMETRO, Xerém, Duque de Caxias, RJ 25250-020 (Brazil); Department of Physics, Pontifícia Universidade Católica do Rio de Janeiro, PUC-Rio, Rio de Janeiro, RJ 22453-970 (Brazil)

2015-12-01

Organic light-emitting diodes using phosphorescent dyes (PHOLEDs) have excellent performance, with internal quantum efficiencies approaching 100%. To maximize their performance, PHOLED devices use a conductive organic host material with a sufficiently dispersed phosphorescent guest to avoid concentration quenching. Fac-tris(2-phenylpyridine) iridium, [Ir(ppy){sub 3}] is one of the most widely used green phosphorescent organic compounds. In this work, we used scanning transmission electron microscopy (STEM) equipped with HAADF (high-angle annular dark-field) and EDS (energy dispersive X-ray spectroscopy) detectors to analyze the distribution of the [Ir(ppy){sub 3}] concentration in the host material. This analysis technique, employed for the first time in co-deposited organic thin films, can simultaneously obtain an image and its respective chemical information, allowing for definitive characterization of the distribution and morphology of [Ir(ppy){sub 3}]. The technique was also used to analyze the effect of the vibration of the substrate during thermal co-deposition of the [Ir(ppy){sub 3}] molecules into an organic matrix. - Highlights: • We present a methodology to analyze the dopant distribution in organic thin films. • The method combines HAADF-STEM imaging and EDS X-ray spectroscopy. • Ir(ppy){sub 3} dopant was co-deposited into Spiro2-CBP organic matrix. • The dopant was co-deposited with and without substrate vibration. • Images and chemical information of the dopant were simultaneously obtained.

Two-dimensional dopant profiling of gallium nitride p-n junctions by scanning capacitance microscopy

Science.gov (United States)

Lamhamdi, M.; Cayrel, F.; Frayssinet, E.; Bazin, A. E.; Yvon, A.; Collard, E.; Cordier, Y.; Alquier, D.

2016-04-01

Two-dimensional imaging of dopant profiles for n and p-type regions are relevant for the development of new power semiconductors, especially for gallium nitride (GaN) for which classical profiling techniques are not adapted. This is a challenging task since it needs a technique with simultaneously good sensitivity, high spatial resolution and high dopant gradient resolution. To face these challenges, scanning capacitance microscopy combined with Atomic Force Microscopy is a good candidate, presenting reproducible results, as demonstrated in literature. In this work, we attempt to distinguish reliably and qualitatively the various doping concentrations and type at p-n and unipolar junctions. For both p-n and unipolar junctions three kinds of samples were prepared and measured separately. The space-charge region of the p-n metallurgical junction, giving rise to different contrasts under SCM imaging, is clearly observed, enlightening the interest of the SCM technique.

Two-dimensional dopant profiling of gallium nitride p–n junctions by scanning capacitance microscopy

Energy Technology Data Exchange (ETDEWEB)

Lamhamdi, M. [GREMAN UMR 7347-Université de Tours, 10 Rue Thales de Milet, BP 7155, 37071 Tours (France); Ecole national des sciences appliquées khouribga, Université Hassan 1er, 26000 Settat (Morocco); Cayrel, F. [GREMAN UMR 7347-Université de Tours, 10 Rue Thales de Milet, BP 7155, 37071 Tours (France); Frayssinet, E. [CRHEA-CNRS, Rue Bernard Grégory, Sophia Antipolis, 06560 Valbonne (France); Bazin, A.E.; Yvon, A.; Collard, E. [STMicroelectronics, 16 Rue Pierre et Marie Curie, BP 7155, 37071 Tours (France); Cordier, Y. [CRHEA-CNRS, Rue Bernard Grégory, Sophia Antipolis, 06560 Valbonne (France); Alquier, D. [GREMAN UMR 7347-Université de Tours, 10 Rue Thales de Milet, BP 7155, 37071 Tours (France)

2016-04-01

Two-dimensional imaging of dopant profiles for n and p-type regions are relevant for the development of new power semiconductors, especially for gallium nitride (GaN) for which classical profiling techniques are not adapted. This is a challenging task since it needs a technique with simultaneously good sensitivity, high spatial resolution and high dopant gradient resolution. To face these challenges, scanning capacitance microscopy combined with Atomic Force Microscopy is a good candidate, presenting reproducible results, as demonstrated in literature. In this work, we attempt to distinguish reliably and qualitatively the various doping concentrations and type at p–n and unipolar junctions. For both p–n and unipolar junctions three kinds of samples were prepared and measured separately. The space-charge region of the p–n metallurgical junction, giving rise to different contrasts under SCM imaging, is clearly observed, enlightening the interest of the SCM technique.

Effect of Dopant Activation on Device Characteristics of InGaN-based Light Emitting Diodes

Science.gov (United States)

Lacroce, Nicholas; Liu, Guangyu; Tan, Chee-Keong; Arif, Ronald A.; Lee, Soo Min; Tansu, Nelson

2015-03-01

Achieving high uniformity in growths and device characteristics of InGaN-based light-emitting diodes (LEDs) is important for large scale manufacturing. Dopant activation and maintaining control of variables affecting dopant activation are critical steps in the InGaN-based light emitting diodes (LEDs) fabrication process. In the epitaxy of large scale production LEDs, in-situ post-growth annealing is used for activating the Mg acceptor dopant in the p-AlGaN and p-GaN of the LEDs. However, the annealing temperature varies with respect to position in the reactor chamber, leading to severe uniform dopant activation issue across the devices. Thus, it is important to understand how the temperature gradient and the resulting variance in Mg acceptor activation will alter the device properties. In this work, we examine the effect of varying p-type doping levels in the p-GaN layers and AlGaN electron blocking layer of the GaN LEDs on the optoelectronic properties including the band profile, carrier concentration, current density, output power and quantum efficiency. By understanding the variations and its effect, the identification of the most critical p-type doping layer strategies to address this variation will be clarified.

Using Dopants to Tune Oxygen Vacancy Formation in Transition Metal Oxide Resistive Memory.

Science.gov (United States)

Jiang, Hao; Stewart, Derek A

2017-05-17

Introducing dopants is an important way to tailor and improve electronic properties of transition metal oxides used as high-k dielectric thin films and resistance switching layers in leading memory technologies, such as dynamic and resistive random access memory (ReRAM). Ta 2 O 5 has recently received increasing interest because Ta 2 O 5 -based ReRAM demonstrates high switching speed, long endurance, and low operating voltage. However, advances in optimizing device characteristics with dopants have been hindered by limited and contradictory experiments in this field. We report on a systematic study on how various metal dopants affect oxygen vacancy formation in crystalline and amorphous Ta 2 O 5 from first principles. We find that isoelectronic dopants and weak n-type dopants have little impact on neutral vacancy formation energy and that p-type dopants can lower the formation energy significantly by introducing holes into the system. In contrast, n-type dopants have a deleterious effect and actually increase the formation energy for charged oxygen vacancies. Given the similar doping trend reported for other binary transition metal oxides, this doping trend should be universally valid for typical binary transition metal oxides. Based on this guideline, we propose that p-type dopants (Al, Hf, Zr, and Ti) can lower the forming/set voltage and improve retention properties of Ta 2 O 5 ReRAM.

Dopant redistribution and electrical activation in silicon following ultra-low energy boron implantation and excimer laser annealing

International Nuclear Information System (INIS)

Whelan, S.; La Magna, A.; Privitera, V.; Mannino, G.; Italia, M.; Bongiorno, C.; Fortunato, G.; Mariucci, L.

2003-01-01

Excimer laser annealing (ELA) of ultra-low-energy (ULE) B-ion implanted Si has been performed. High-resolution transmission electron microscopy has been used to assess the as-implanted damage and the crystal recovery following ELA. The electrical activation and redistribution of B in Si during ELA has been investigated as a function of the laser energy density (melted depth), the implant dose, and the number of laser pulses (melt time). The activated and retained dose has been evaluated with spreading resistance profiling and secondary ion mass spectrometry. A significant amount of the implanted dopant was lost from the sample during ELA. However, the dopant that was retained in crystal material was fully activated following rapid resolidification. At an atomic concentration below the thermodynamic limit, the activation efficiency (dose activated/dose implanted into Si material) was a constant for a fixed melt depth, irrespective of the dose implanted and hence the total activated dose was raised as the implant dose was increased. The electrical activation was increased for high laser energy density annealing when the dopant was redistributed over a deeper range

High Thermoelectric Figure of Merit by Resonant Dopant in Half-Heusler Alloys

OpenAIRE

Chen, Long; Liu, Yamei; He, Jian; Tritt, Terry M.; Poon, S. Joseph

2017-01-01

Half-Heusler alloys have been one of the benchmark high temperature thermoelectric materials owing to their thermal stability and promising figure of merit ZT. Simonson et al. early showed that small amounts of vanadium doped in Hf0.75Zr0.25NiSn enhanced the Seebeck coefficient and correlated the change with the increased density of states near the Fermi level. We herein report a systematic study on the role of vanadium (V), niobium (Nb), and tantalum (Ta) as prospective resonant dopants in e...

MOS Capacitance—Voltage Characteristics II. Sensitivity of Electronic Trapping at Dopant Impurity from Parameter Variations

International Nuclear Information System (INIS)

Jie Binbin; Sah Chihtang

2011-01-01

Low-frequency and high-frequency Capacitance—Voltage (C—V) curves of Metal—Oxide—Semiconductor Capacitors (MOSC), including electron and hole trapping at the dopant donor and acceptor impurities, are presented to illustrate giant trapping capacitances, from > 0.01C OX to > 10C OX . Five device and materials parameters are varied for fundamental trapping parameter characterization, and electrical and optical signal processing applications. Parameters include spatially constant concentration of the dopant-donor-impurity electron trap, N DD , the ground state electron trapping energy level depth measured from the conduction band edge, E C –E D , the degeneracy of the trapped electron at the ground state, g D , the device temperature, T, and the gate oxide thickness, x OX . (invited papers)

Understanding and controlling transient enhanced dopant diffusion in silicon

International Nuclear Information System (INIS)

Stolk, P.A.; Gossmann, H.J.; Eaglesham, D.J.; Jacobson, D.C.; Poate, J.M.; Luftman, H.S.

1995-01-01

Implanted B and P dopants in Si exhibit transient enhanced diffusion (TED) during initial annealing which arises from the excess interstitials generated by the implant. In order to study the mechanisms of TED, the authors have used B doping marker layers in Si to probe the injection of interstitials from near-surface, non-amorphizing Si implants during annealing. The in-diffusion of interstitials is limited by trapping at impurities and has an activation energy of ∼3.5 eV. Substitutional C is the dominant trapping center with a binding energy of 2--2.5 eV. The high interstitial supersaturation adjacent to the implant damage drives substitutional B into metastable clusters at concentrations below the B solid solubility limit. Transmission electron microscopy shows that the interstitials driving TED are emitted from {311} defect clusters in the damage region at a rate which also exhibits an activation energy of 3.6 eV. The population of excess interstitials is strongly reduced by incorporating substitutional C in Si to levels of ∼10 19 /cm 3 prior to ion implantation. This provides a promising method for suppressing TED, thus enabling shallow junction formation in future Si devices through dopant implantation

The effect of dopants on laser imprint mitigation

Science.gov (United States)

Phillips, Lee; Gardner, John H.; Bodner, Stephen E.; Colombant, Denis; Dahlburg, Jill

1999-11-01

An intact implosion of a pellet for direct-drive ICF requires that the perturbations imprinted by the laser be kept below some threshold. We report on simulations of targets that incorporate very small concentrations of a high-Z dopant in the ablator, to increase the electron density in the ablating plasma, causing the laser to be absorbed far enough from the solid ablator to achieve a substantial degree of thermal smoothing. These calculations were performed using NRL's FAST radiation hydrodynamics code(J.H. Gardner, A.J. Schmitt, et al., Phys. Plasmas) 5, 1935 (1998), incorporating the flux-corrected transport algorithm and opacities generated by an STA code, with non-LTE radiation transport based on the Busquet method.

A β-cyclodextrin based binary dopant for polyaniline: Structural, thermal, electrical, and sensing performance

Energy Technology Data Exchange (ETDEWEB)

Sen, Tanushree; Mishra, Satyendra [University Institute of Chemical Technology, North Maharashtra University, Jalgaon 425001, Maharashtra (India); Shimpi, Navinchandra G., E-mail: navin_shimpi@rediffmail.com [Department of Chemistry, University of Mumbai, Kalina, Mumbai 400098, Maharashtra (India)

2017-06-15

Highlights: • A binary dopant based on β-cyclodextrin has been proposed for PANI. • The binary dopant provided long term stability to electrically conducting PANI. • The β-cyclodextrin based binary dopant rendered PANI sensitive towards CO at RT. - Abstract: The effect of hydrochloric acid/β-cyclodextrin (HCl/β-CD) binary dopant on the morphological, thermal, electrical, and sensing properties of PANI was investigated and compared with those of the conventionally doped PANI. The PANI samples were characterized using FTIR, UV–Vis, {sup 1}H NMR, and FESEM. Significant changes were observed in the structural, thermal, and electrical character of PANI doped with the HCl/β-CD binary dopant. A higher doping level was obtained for the PANI-binary dopant system, as observed from its {sup 1}H NMR spectra. Moreover, the binary dopant imparted long-term stability to the sensor in its conductive form. In addition, the PANI-binary dopant system exhibited a significantly high gas response towards carbon monoxide gas at room temperature.

Dopant distributions in n-MOSFET structure observed by atom probe tomography

International Nuclear Information System (INIS)

Inoue, K.; Yano, F.; Nishida, A.; Takamizawa, H.; Tsunomura, T.; Nagai, Y.; Hasegawa, M.

2009-01-01

The dopant distributions in an n-type metal-oxide-semiconductor field effect transistor (MOSFET) structure were analyzed by atom probe tomography. The dopant distributions of As, P, and B atoms in a MOSFET structure (gate, gate oxide, channel, source/drain extension, and halo) were obtained. P atoms were segregated at the interface between the poly-Si gate and the gate oxide, and on the grain boundaries of the poly-Si gate, which had an elongated grain structure along the gate height direction. The concentration of B atoms was enriched near the edge of the source/drain extension where the As atoms were implanted.

Dopant distributions in n-MOSFET structure observed by atom probe tomography.

Science.gov (United States)

Inoue, K; Yano, F; Nishida, A; Takamizawa, H; Tsunomura, T; Nagai, Y; Hasegawa, M

2009-11-01

The dopant distributions in an n-type metal-oxide-semiconductor field effect transistor (MOSFET) structure were analyzed by atom probe tomography. The dopant distributions of As, P, and B atoms in a MOSFET structure (gate, gate oxide, channel, source/drain extension, and halo) were obtained. P atoms were segregated at the interface between the poly-Si gate and the gate oxide, and on the grain boundaries of the poly-Si gate, which had an elongated grain structure along the gate height direction. The concentration of B atoms was enriched near the edge of the source/drain extension where the As atoms were implanted.

High thermoelectric figure of merit by resonant dopant in half-Heusler alloys

Science.gov (United States)

Chen, Long; Liu, Yamei; He, Jian; Tritt, Terry M.; Poon, S. Joseph

2017-06-01

Half-Heusler alloys have been one of the benchmark high temperature thermoelectric materials owing to their thermal stability and promising figure of merit ZT. Simonson et al. early showed that small amounts of vanadium doped in Hf0.75Zr0.25NiSn enhanced the Seebeck coefficient and correlated the change with the increased density of states near the Fermi level. We herein report a systematic study on the role of vanadium (V), niobium (Nb), and tantalum (Ta) as prospective resonant dopants in enhancing the ZT of n-type half-Heusler alloys based on Hf0.6Zr0.4NiSn0.995Sb0.005. The V doping was found to increase the Seebeck coefficient in the temperature range 300-1000 K, consistent with a resonant doping scheme. In contrast, Nb and Ta act as normal n-type dopants, as evident by the systematic decrease in electrical resistivity and Seebeck coefficient. The combination of enhanced Seebeck coefficient due to the presence of V resonant states and the reduced thermal conductivity has led to a state-of-the-art ZT of 1.3 near 850 K in n-type (Hf0.6Zr0.4)0.99V0.01NiSn0.995Sb0.005 alloys.

Dopant atoms as quantum components in silicon nanoscale devices

Science.gov (United States)

Zhao, Xiaosong; Han, Weihua; Wang, Hao; Ma, Liuhong; Li, Xiaoming; Zhang, Wang; Yan, Wei; Yang, Fuhua

2018-06-01

Recent progress in nanoscale fabrication allows many fundamental studies of the few dopant atoms in various semiconductor nanostructures. Since the size of nanoscale devices has touched the limit of the nature, a single dopant atom may dominate the performance of the device. Besides, the quantum computing considered as a future choice beyond Moore's law also utilizes dopant atoms as functional units. Therefore, the dopant atoms will play a significant role in the future novel nanoscale devices. This review focuses on the study of few dopant atoms as quantum components in silicon nanoscale device. The control of the number of dopant atoms and unique quantum transport characteristics induced by dopant atoms are presented. It can be predicted that the development of nanoelectronics based on dopant atoms will pave the way for new possibilities in quantum electronics. Project supported by National Key R&D Program of China (No. 2016YFA0200503).

Dopant concentration and thermoluminescence (TL) properties of tailor-made Ge-doped SiO2 fibres

International Nuclear Information System (INIS)

Zahaimi, Nurul Arina; Ooi Abdullah, Mohd Haris Ridzuan; Zin, Hafiz; Abdul Rahman, Ahmad Lutfi; Hashim, Suhairul; Saripan, Mohd Iqbal; Paul, Mukul Chandra; Bradley, D.A.; Abdul Rahman, Ahmad Taufek

2014-01-01

Study focuses on characterisation of diverse concentrations of Ge-doped SiO 2 fibre as a potential thermoluminescence (TL) system for radiotherapy dosimetry. Irradiations were made using a linear accelerator providing 6 MV and 10 MV photon beams. Investigation has been done on various doped core diameter Ge-doped SiO 2 glass fibres such as commercial telecommunication fibres of 8 µm and 9 µm (CorActive High Tech, Canada), tailor-made fibres of 23 and 50 µm produced by the Central Glass and Ceramic Research Institute Kolkata, and tailor-made fibres of 11 µm produced by the University of Malaya Photonics Research Centre. The fibres have been characterised for TL sensitivity, reproducibility, dose- and energy-dependence. The area under the TL glow curve increases with increasing core diameter. For repeat irradiations at a fixed dose the dosimeter produces a flat response better than 4% (1SD) of the mean of the TL distribution. Minimal TL signal fading was found, less than 0.5% per day post irradiation. Linearity of TL has been observed with a correlation coefficient (r 2 ) of better than 0.980 (at 95% confidence level). For particular dopant concentrations, the least square fits show the change in TL yield, in counts per second per unit mass, obtained from 50 µm core diameter fibres irradiated at 6 MV of photon to be 8 times greater than that of 8 µm core diameter fibre. With respect to energy response, the TL yield at 10 MV decreases by∼5% compared to that at 6 MV, primarily due to the lower mass energy absorption coefficient at higher photon energy. These early results indicate that selectively screened fibres can be developed into a promising TL system, offering high spatial resolution capability and, with this, verification of complex radiotherapy dose distributions. - Highlights: • We examined the TL glow curve intensity for various diameter sizes of germanium doped silica glass fibre. • TL sensitivity increased with the increase of fibre core

The interplay between dopants and oxygen vacancies in the magnetism of V-doped TiO2

KAUST Repository

Grau-Crespo, Ricardo

2011-08-03

Density functional theory calculations indicate that the incorporation of V into Ti lattice positions of rutile TiO2 leads to magnetic V 4 + species, but the extension and sign of the coupling between dopant moments confirm that ferromagnetic order cannot be reached via low-concentration doping in the non-defective oxide. Oxygen vacancies can introduce additional magnetic centres, and we show here that one of the effects of vanadium doping is to reduce the formation energies of these defects. In the presence of both V dopants and O vacancies all the spins tend to align with the same orientation. We conclude that V doping favours the ferromagnetic behaviour of TiO2 not only by introducing spins associated with the dopant centres but also by increasing the concentration of oxygen vacancies with respect to the pure oxide. © 2001 IOP Publishing Ltd.

The interplay between dopants and oxygen vacancies in the magnetism of V-doped TiO2

KAUST Repository

Grau-Crespo, Ricardo; Schwingenschlö gl, Udo

2011-01-01

Density functional theory calculations indicate that the incorporation of V into Ti lattice positions of rutile TiO2 leads to magnetic V 4 + species, but the extension and sign of the coupling between dopant moments confirm that ferromagnetic order cannot be reached via low-concentration doping in the non-defective oxide. Oxygen vacancies can introduce additional magnetic centres, and we show here that one of the effects of vanadium doping is to reduce the formation energies of these defects. In the presence of both V dopants and O vacancies all the spins tend to align with the same orientation. We conclude that V doping favours the ferromagnetic behaviour of TiO2 not only by introducing spins associated with the dopant centres but also by increasing the concentration of oxygen vacancies with respect to the pure oxide. © 2001 IOP Publishing Ltd.

Exciton-dopant and exciton-charge interactions in electronically doped OLEDs

International Nuclear Information System (INIS)

Williams, Christopher; Lee, Sergey; Ferraris, John; Zakhidov, A. Anvar

2004-01-01

The electronic dopants, like tetrafluorocyanoquinodimethane (F 4 -TCNQ) molecules, used for p-doping of hole transport layers in organic light-emitting diodes (OLEDs) are found to quench the electroluminescence (EL) if they diffuse into the emissive layer. We observed EL quenching in OLED with F 4 -TCNQ doped N,N'-diphenyl-N'N'-bis(1-naphthyl)-1,1'-biphenyl-4,4'-diamine hole transport layer at large dopant concentrations, >5%. To separate the effects of exciton-dopant quenching, from exciton-polaron quenching we have intentionally doped the emissive layer of (8-tris-hydroxyquinoline) with three acceptors (A) of different electron affinities: F 4 -TCNQ, TCNQ, and C 60 , and found that C 60 is the strongest EL-quencher, while F 4 -TCNQ is the weakest, contrary to intuitive expectations. The new effects of charge transfer and usually considered energy transfer from exciton to neutral (A) and charged acceptors (A - ) are compared as channels for non-radiative Ex-A decay. At high current loads the EL quenching is observed, which is due to decay of Ex on free charge carriers, hole polarons P + . We consider contributions to Ex-P + interaction by short-range charge transfer and describe the structure of microscopic charge transfer (CT)-processes responsible for it. The formation of metastable states of 'charged excitons' (predicted and studied by Agranovich et al. Chem. Phys. 272 (2001) 159) by electron transfer from a P to an Ex is pointed out, and ways to suppress non-radiative Ex-P decay are suggested

Perspective analysis of tri gate germanium tunneling field-effect transistor with dopant segregation region at source/drain

Science.gov (United States)

Liu, Liang-kui; Shi, Cheng; Zhang, Yi-bo; Sun, Lei

2017-04-01

A tri gate Ge-based tunneling field-effect transistor (TFET) has been numerically studied with technology computer aided design (TCAD) tools. Dopant segregated Schottky source/drain is applied to the device structure design (DS-TFET). The characteristics of the DS-TFET are compared and analyzed comprehensively. It is found that the performance of n-channel tri gate DS-TFET with a positive bias is insensitive to the dopant concentration and barrier height at n-type drain, and that the dopant concentration and barrier height at a p-type source considerably affect the device performance. The domination of electron current in the entire BTBT current of this device accounts for this phenomenon and the tri-gate DS-TFET is proved to have a higher performance than its dual-gate counterpart.

Dependence of the up-conversion emission of Li+ co-doped Y2O3:Er3+ films with dopant concentration

International Nuclear Information System (INIS)

Meza-Rocha, A.N.; Huerta, E.F.; Caldiño, U.; Carmona-Téllez, S.; Bettinelli, M.; Speghini, A.; Pelli, S.; Righini, G.C.

2015-01-01

The effect of dopant concentration on the up-conversion emission, and in particular on the Er 3+ related green and red emissions of spray pyrolysis deposited films of Y 2 O 3 :Er 3+ co-doped with Li + , is reported. Er 3+ concentrations in the films in the range of 1.1–5.6 at% (1.5–14 at% Er 3+ in the spraying solution) were studied, as well as the effect of co-doping them with Li + . Large concentrations of Er 3+ favor the red emission, especially for contents higher than 10 at% in the spraying solution. Li + co-doping improves the green and red emissions up to 365 and 171 times, respectively, depending on the Er 3+ and Li + concentrations. - Highlights: Up-converting Y 2 O 3 :Er 3+ and Y 2 O 3 :Er 3+ , Li + films were deposited by spray pyrolysis. The effect of Li + co-doping on the green and red UC Er 3+ emission is reported. Li + co-doping improves the green and red emission up to 365 and 171 times

Comparative concentration analysis of Cr and Co in FeSi2 films performed by ERDA and RBS

International Nuclear Information System (INIS)

Bohne, W.; Reinsperger, G.-U.; Roehrich, J.; Roeschert, G.; Selle, B.; Stauss, P.

2000-01-01

Thin films of β-FeSi 2 doped by Co or Cr were grown on Si substrates by molecular beam epitaxy (MBE) using three separately controlled evaporation sources. The dopant concentration was measured concurrently by heavy-ion ERDA with 129 Xe ions of 140-250 MeV, by heavy-ion RBS with 15 MeV 14 N and by standard RBS with 1.4 MeV 4 He ions. Among these techniques, the TOF-ERDA was most powerful in providing a high mass resolution and a low detection limit for Co and Cr (∼0.1 at.%). Because of the complete overlap of the dopant signals with the Fe signal the standard RBS spectra were evaluated by relying on the differences between the scattering cross-sections from the dopant atoms and Fe. This approach proved to be applicable as far as the dopants had a constant depth profile with sufficiently high concentration. For Cr concentrations exceeding the miscibility limit the RBS results deviate significantly from those of ERDA due to increasing dopant depth inhomogeneities

Multicomponent mixed dopant optimization for rapid screening of polycyclic aromatic hydrocarbons using ultra high performance liquid chromatography coupled to atmospheric pressure photoionization high-resolution mass spectrometry

KAUST Repository

Sioud, Salim; Amad, Maan H.; Al-Talla, Zeyad

2012-01-01

with water-soluble organic solvents. In order to achieve a more efficient and less toxic dopant, a multicomponent mixed dopant was explored. METHODS A multicomponent mixed dopant for non-targeted rapid screening of polycyclic aromatic hydrocarbons (PAHs

Materials properties of hafnium and zirconium silicates: Metal interdiffusion and dopant penetration studies

Science.gov (United States)

Quevedo Lopez, Manuel Angel

Hafnium and Zirconium based gate dielectrics are considered potential candidates to replace SiO2 or SiON as the gate dielectric in CMOS processing. Furthermore, the addition of nitrogen into this pseudo-binary alloy has been shown to improve their thermal stability, electrical properties, and reduce dopant penetration. Because CMOS processing requires high temperature anneals (up to 1050°C), it is important to understand the diffusion properties of any metal associated with the gate dielectric in silicon at these temperatures. In addition, dopant penetration from the doped polysilicon gate into the Si channel at these temperatures must also be studied. Impurity outdiffusion (Hf, Zr) from the dielectric, or dopant (B, As, P) penetration through the dielectric into the channel region would likely result in deleterious effects upon the carrier mobility. In this dissertation extensive thermal stability studies of alternate gate dielectric candidates ZrSixOy and HfSixO y are presented. Dopant penetration studies from doped-polysilicon through HfSixOy and HfSixOyNz are also presented. Rutherford Backscattering Spectroscopy (RBS), Heavy Ion RBS (HI-RBS), X-ray Photoelectron Spectroscopy (XPS), High Resolution Transmission Electron Microscopy (HR-TEM), and Time of Flight and Dynamic Secondary Ion Mass Spectroscopy (ToF-SIMS, D-SIMS) methods were used to characterize these materials. The dopant diffusivity is calculated by modeling of the dopant profiles in the Si substrate. In this disseration is reported that Hf silicate films are more stable than Zr silicate films, from the metal interdiffusion point of view. On the other hand, dopant (B, As, and P) penetration is observed for HfSixO y films. However, the addition of nitrogen to the Hf - Si - O systems improves the dopant penetration properties of the resulting HfSi xOyNz films.

Dopant ink composition and method of fabricating a solar cell there from

Energy Technology Data Exchange (ETDEWEB)

Loscutoff, Paul; Wu, Kahn; Molesa, Steven Edward

2017-10-25

Dopant ink compositions and methods of fabricating solar cells there from are described. A dopant ink composition may include a cross-linkable matrix precursor, a bound dopant species, and a solvent. A method of fabricating a solar cell may include delivering a dopant ink composition to a region above a substrate. The dopant ink composition includes a cross-linkable matrix precursor, a bound dopant species, and a solvent. The method also includes baking the dopant ink composition to remove a substantial portion of the solvent of the dopant ink composition, curing the baked dopant ink composition to cross-link a substantial portion of the cross-linkable matrix precursor of the dopant ink composition, and driving dopants from the cured dopant ink composition toward the substrate.

Dopant ink composition and method of fabricating a solar cell there from

Science.gov (United States)

Loscutoff, Paul; Wu, Kahn; Molesa, Steven Edward

2015-03-31

Dopant ink compositions and methods of fabricating solar cells there from are described. A dopant ink composition may include a cross-linkable matrix precursor, a bound dopant species, and a solvent. A method of fabricating a solar cell may include delivering a dopant ink composition to a region above a substrate. The dopant ink composition includes a cross-linkable matrix precursor, a bound dopant species, and a solvent. The method also includes baking the dopant ink composition to remove a substantial portion of the solvent of the dopant ink composition, curing the baked dopant ink composition to cross-link a substantial portion of the cross-linkable matrix precursor of the dopant ink composition, and driving dopants from the cured dopant ink composition toward the substrate.

Mechanism of dopant-vacancy association in α-quartz GeO2

KAUST Repository

Wang, Hao; Chroneos, Alexander; Schwingenschlö gl, Udo

2013-01-01

Improving the electron mobility of devices such as Ge metal oxide semiconductor field effect transistors requires good Ge/dielectric interfaces. GeO2 thus is reconsidered as a passivation layer for Ge. However, O-vacancies need to be controlled as they have a deleterious impact on the properties. We employ electronic structure calculations to investigate the introduction of trivalent ions (Al, Y, and La) in α-quartz GeO2. The binding energies of the dopant-vacancy pairs reveal that dopants can be used to control the O-vacancies and reduce the induced dangling bonds. It is proposed that the introduction of Al will limit the concentration of O-vacancies at low Fermi energy.

Mechanism of dopant-vacancy association in α-quartz GeO2

KAUST Repository

Wang, Hao

2013-02-28

Improving the electron mobility of devices such as Ge metal oxide semiconductor field effect transistors requires good Ge/dielectric interfaces. GeO2 thus is reconsidered as a passivation layer for Ge. However, O-vacancies need to be controlled as they have a deleterious impact on the properties. We employ electronic structure calculations to investigate the introduction of trivalent ions (Al, Y, and La) in α-quartz GeO2. The binding energies of the dopant-vacancy pairs reveal that dopants can be used to control the O-vacancies and reduce the induced dangling bonds. It is proposed that the introduction of Al will limit the concentration of O-vacancies at low Fermi energy.

Functionally Graded Thermoelectric Material though One Step Band Gap and Dopant Engineering

DEFF Research Database (Denmark)

Jensen, Ellen Marie; Borup, Kasper Andersen; Cederkrantz, Daniel

, and dopant concentration. Parameters relevant to the thermoelectric properties have been determined along the pulling direction. All of these properties exhibit the wanted gradient. It has thereby been shown that engineering of the electrical contributions to the thermoelectric properties of a material...

New cyclometalated Iridium(III) beta-dicetone complex as phosphorescent dopant in Organic light emitting devices

Science.gov (United States)

Ivanov, P.; Petrova, P.; Stanimirov, S.; Tomova, R.

2017-01-01

A new Bis[4-(benzothiazolato-N,C2‧-2-yl)-N,N-dimethylaniline]Iridium(III) acetylacetonate (Me2N-bt) 2Ir(acac) was synthesized and identified by 1H NMR and elemental analysis. The application of the new compound as a dopant in the hole transporting layer (HTL) of Organic light emitting diode (OLED) structure: HTL/EL/ETL, where HTL was N,N’-bis(3-methylphenyl)-N,N’-diphenylbenzidine (TPD), incorporated in Poly(N-vinylcarbazole) (PVK) matrix, EL - electroluminescent layer of Bis(8-hydroxy-2-methylquinoline)-(4-phenylpheno-xy)aluminum (BAlq) and ETL - electron-transporting layer of Tris-(8-hydroxyquinoline) aluminum (Alq3) or Bis[2-(2-benzothiazoly) phenolato]zinc (Zn(btz)2). We established that the electroluminescent spectra of OLEDs at different concentrations of the dopant were basically the sum of the greenish-blue emission of BAlq and yellowish-green emission of Ir complex. It was found that with increasing of the dopant concentration the relative electroluminescent intensity of Iridium complex emission increased and this of BAlq decreased and as a result the fine tuning of OLED color was observed.

New cyclometalated iridium(III) complex as a phosphorescent dopant in organic light emitting devices

Science.gov (United States)

Ivanov, P.; Tomova, R.; Petrova, P.; Stanimirov, S.; Petkov, I.

2014-05-01

A new cyclometalated iridium (III) bis[2-(4-chlorophenyl)benzothiazolato-N,C2]-acetylacetonate, (Cl-bt)2Ir(acac), was synthesized and identified by 1H NMR and elemental analysis. The application was studied of the new compound as a dopant in the hole transporting layer (HTL) of the following organic light emitting diode (OLED) structure: HTL/EL/ETL, where HTL was 4,4'-bis(9H-carbazol-9-yl)biphenyl (CBP) or N,N'-bis(3-methylphenyl)-N,N'-diphenylbenzidine (TPD), incorporated in a poly(N-vinylcarbazole) (PVK) matrix; EL was an electroluminescent layer of bis(8-hydroxy-2-methylquinoline)-(4-phenylpheno-xy) aluminum (BAlq); and ETL was an electron-transporting layer of bis[2-(2-benzothiazoly) phenolato]zinc(II) (Zn(btz)2). We established that the electroluminescence spectra of the OLEDs at different dopant concentrations were basically the sum of the greenish-blue emission of BAlq and the yellowish-green emission of the Ir complex. It was also found that increasing the dopant concentration resulted in an increase in the relative electroluminescent intensity of the Ir complex emission, while that of BAlq decreased, thus a fine tuning of the OLED color was observed.

Physical properties of high-Tc superconducting oxides. Modification of tc using organic dopants. Final report. Proprietes physiques d'oxydes supraconducteurs a haute Tc. Modification de tc sous l'effet de dopants organiques

Energy Technology Data Exchange (ETDEWEB)

Brau, A

1993-01-01

An attempt was made to significantly modify the Tc transition temperature of certain copper-based superconducting oxides by introducing organic or mineral dopants, and to study the mobility of 300K-carriers in crystallized tallium-base superconducting oxides. Since the critical transition temperature of superconducting oxides is highly influenced by the density of the free carriers they contain, the authors tried making superconducting powders react with either an organic electron acceptor or a mineral compound. The goal was to increase the density of the holes by altering the copper's degree of oxidation. Their preparatory work showed a direct charge-transfer reaction between the electron-donor copper and the acceptor TCNQ and studied the degree to which the electron acceptor can alter the copper's oxidation. Initial results also showed that dopants can affect superconducting Tc and the course of R(T) curves.

Directed Atom-by-Atom Assembly of Dopants in Silicon.

Science.gov (United States)

Hudak, Bethany M; Song, Jiaming; Sims, Hunter; Troparevsky, M Claudia; Humble, Travis S; Pantelides, Sokrates T; Snijders, Paul C; Lupini, Andrew R

2018-05-17

The ability to controllably position single atoms inside materials is key for the ultimate fabrication of devices with functionalities governed by atomic-scale properties. Single bismuth dopant atoms in silicon provide an ideal case study in view of proposals for single-dopant quantum bits. However, bismuth is the least soluble pnictogen in silicon, meaning that the dopant atoms tend to migrate out of position during sample growth. Here, we demonstrate epitaxial growth of thin silicon films doped with bismuth. We use atomic-resolution aberration-corrected imaging to view the as-grown dopant distribution and then to controllably position single dopants inside the film. Atomic-scale quantum-mechanical calculations corroborate the experimental findings. These results indicate that the scanning transmission electron microscope is of particular interest for assembling functional materials atom-by-atom because it offers both real-time monitoring and atom manipulation. We envision electron-beam manipulation of atoms inside materials as an achievable route to controllable assembly of structures of individual dopants.

Influence of the dopant during the one step mechano-chemical synthesis of sodium alanate

International Nuclear Information System (INIS)

Rongeat, C; Geipel, C; Llamas-Jansa, I; Schultz, L; Gutfleisch, O

2009-01-01

High-pressure reactive milling under hydrogen atmosphere is used for the one-step synthesis of doped sodium alanate. In-situ monitoring of the pressure and the temperature inside the vial gives a direct feedback about the reactions occurring during the milling. This information is used to study the influence of the dopant during synthesis, e.g. the amount of dopant added. The study of the pressure variations during milling is a reliable tool for screening the efficiency of different dopants.

Theory of space charge limited currents in films and nanowires with dopants

Science.gov (United States)

Zhang, Xiaoguang; Pantelides, Sokrates

2015-03-01

We show that proper description of the space charge limited currents (SCLC) in a homogeneous bulk material must account fully for the effect of the dopants and the interplay between dopants and traps. The sharp rise in the current at the trap-filled-limit (TFL) is partially mitigated by the dopant energy levels and the Frenkel effect, namely the lowering of the ionization energy by the electric field, which is screened by the free carriers. In nanowires, lack of effective screening causes the trap occupation at small biases to reach a high level comparable to the TFL in bulk. This explains the high current density in SCLCs observed in nanowires. This work is supported by the LDRD program at ORNL. Portion of this research was conducted at the Center for Nanophase Materials Sciences, which is a DOE Office of Science User Facility.

Influence of pentavalent dopant addition to polarization and bioactivity of hydroxyapatite

International Nuclear Information System (INIS)

Dhal, Jharana; Bose, Susmita; Bandyopadhyay, Amit

2013-01-01

Influence of pentavalent tantalum doping in bulk hydroxyapatite (HAp) ceramics has been investigated for polarizability and bioactivity. Phase analysis from X-ray diffraction measurement indicates that increasing dopant concentration decreased the amount of HAp phase and increased β-TCP and/or α-TCP phases during sintering at 1250 °C in a muffle furnace. Results from thermally stimulated depolarization current (TSDC) measurements showed that doping hindered charge storage ability in HAp ceramics, and doped samples stored fewer charge compared to pure HAp. However, doping enhanced wettability of HAp samples, which was improved further due to polarization. In vitro human osteoblast cell–material interaction study revealed an increase in bioactivity due to dopant addition and polarization compared to pure HAp. This increase in bioactivity was attributed to the increase in wettability due to surface charge and dopant addition. - Highlights: • Tantalum doping makes HAp unstable during sintering at 1250 °C and forms TCP. • Tantalum doping reduces charge storage ability of HAp ceramics. • Even with lower charge storage ability tantalum doping improves wettability. • Tantalum doping enhances bioactivity of calcium phosphate based sintered compacts

Finite element simulations of electrostatic dopant potentials in thin semiconductor specimens for electron holography

Energy Technology Data Exchange (ETDEWEB)

Somodi, P.K.; Twitchett-Harrison, A.C.; Midgley, P.A. [Department of Materials Science and Metallurgy, University of Cambridge, Pembroke Street, Cambridge CB2 3QZ (United Kingdom); Kardynał, B.E. [Peter Grünberg Institute 9, Forschungszentrum Jülich, D-52425 Jülich (Germany); Barnes, C.H.W. [Department of Physics, University of Cambridge, Madingley Road, Cambridge CB3 0HE (United Kingdom); Dunin-Borkowski, R.E., E-mail: rafaldb@gmail.com [Ernst Ruska-Centre for Microscopy and Spectroscopy with Electrons and Peter Grünberg Institute 5, Forschungszentrum Jülich, D-52425 Jülich (Germany)

2013-11-15

Two-dimensional finite element simulations of electrostatic dopant potentials in parallel-sided semiconductor specimens that contain p–n junctions are used to assess the effect of the electrical state of the surface of a thin specimen on projected potentials measured using off-axis electron holography in the transmission electron microscope. For a specimen that is constrained to have an equipotential surface, the simulations show that the step in the projected potential across a p–n junction is always lower than would be predicted from the properties of the bulk device, but is relatively insensitive to the value of the surface state energy, especially for thicker specimens and higher dopant concentrations. The depletion width measured from the projected potential, however, has a complicated dependence on specimen thickness. The results of the simulations are of broader interest for understanding the influence of surfaces and interfaces on electrostatic potentials in nanoscale semiconductor devices. - Highlights: • Finite element simulations are performed to calculate electrostatic dopant potentials in TEM specimens that contain p–n junctions. • The effect of the electrical state of the specimen surface on the projected potential is assessed for equipotential specimen surfaces. • The step in projected potential is always found to be lower than the step in potential in the bulk device. • The step in projected potential is least sensitive to surface state energy for thicker specimens and higher dopant concentrations. • The depletion width measured from the projected potential has a complicated dependence on specimen thickness.

Finite element simulations of electrostatic dopant potentials in thin semiconductor specimens for electron holography

International Nuclear Information System (INIS)

Somodi, P.K.; Twitchett-Harrison, A.C.; Midgley, P.A.; Kardynał, B.E.; Barnes, C.H.W.; Dunin-Borkowski, R.E.

2013-01-01

Two-dimensional finite element simulations of electrostatic dopant potentials in parallel-sided semiconductor specimens that contain p–n junctions are used to assess the effect of the electrical state of the surface of a thin specimen on projected potentials measured using off-axis electron holography in the transmission electron microscope. For a specimen that is constrained to have an equipotential surface, the simulations show that the step in the projected potential across a p–n junction is always lower than would be predicted from the properties of the bulk device, but is relatively insensitive to the value of the surface state energy, especially for thicker specimens and higher dopant concentrations. The depletion width measured from the projected potential, however, has a complicated dependence on specimen thickness. The results of the simulations are of broader interest for understanding the influence of surfaces and interfaces on electrostatic potentials in nanoscale semiconductor devices. - Highlights: • Finite element simulations are performed to calculate electrostatic dopant potentials in TEM specimens that contain p–n junctions. • The effect of the electrical state of the specimen surface on the projected potential is assessed for equipotential specimen surfaces. • The step in projected potential is always found to be lower than the step in potential in the bulk device. • The step in projected potential is least sensitive to surface state energy for thicker specimens and higher dopant concentrations. • The depletion width measured from the projected potential has a complicated dependence on specimen thickness

Oxygen-induced high diffusion rate of magnesium dopants in GaN/AlGaN based UV LED heterostructures.

Science.gov (United States)

Michałowski, Paweł Piotr; Złotnik, Sebastian; Sitek, Jakub; Rosiński, Krzysztof; Rudziński, Mariusz

2018-05-23

Further development of GaN/AlGaN based optoelectronic devices requires optimization of the p-type material growth process. In particular, uncontrolled diffusion of Mg dopants may decrease the performance of a device. Thus it is meaningful to study the behavior of Mg and the origins of its diffusion in detail. In this work we have employed secondary ion mass spectrometry to study the diffusion of magnesium in GaN/AlGaN structures. We show that magnesium has a strong tendency to form Mg-H complexes which immobilize Mg atoms and restrain their diffusion. However, these complexes are not present in samples post-growth annealed in an oxygen atmosphere or Al-rich AlGaN structures which naturally have a high oxygen concentration. In these samples, more Mg atoms are free to diffuse and thus the average diffusion length is considerably larger than for a sample annealed in an inert atmosphere.

The ionization mechanisms in direct and dopant-assisted atmospheric pressure photoionization and atmospheric pressure laser ionization.

Science.gov (United States)

Kauppila, Tiina J; Kersten, Hendrik; Benter, Thorsten

2014-11-01

A novel, gas-tight API interface for gas chromatography-mass spectrometry was used to study the ionization mechanism in direct and dopant-assisted atmospheric pressure photoionization (APPI) and atmospheric pressure laser ionization (APLI). Eight analytes (ethylbenzene, bromobenzene, naphthalene, anthracene, benzaldehyde, pyridine, quinolone, and acridine) with varying ionization energies (IEs) and proton affinities (PAs), and four common APPI dopants (toluene, acetone, anisole, and chlorobenzene) were chosen. All the studied compounds were ionized by direct APPI, forming mainly molecular ions. Addition of dopants suppressed the signal of the analytes with IEs above the IE of the dopant. For compounds with suitable IEs or Pas, the dopants increased the ionization efficiency as the analytes could be ionized through dopant-mediated gas-phase reactions, such as charge exchange, proton transfer, and other rather unexpected reactions, such as formation of [M + 77](+) in the presence of chlorobenzene. Experiments with deuterated toluene as the dopant verified that in case of proton transfer, the proton originated from the dopant instead of proton-bound solvent clusters, as in conventional open or non-tight APPI sources. In direct APLI using a 266 nm laser, a narrower range of compounds was ionized than in direct APPI, because of exceedingly high IEs or unfavorable two-photon absorption cross-sections. Introduction of dopants in the APLI system changed the ionization mechanism to similar dopant-mediated gas-phase reactions with the dopant as in APPI, which produced mainly ions of the same form as in APPI, and ionized a wider range of analytes than direct APLI.

Dopant-induced ignition of helium nanoplasmas—a mechanistic study

Science.gov (United States)

Heidenreich, Andreas; Schomas, Dominik; Mudrich, Marcel

2017-12-01

Helium (He) nanodroplets irradiated by intense near-infrared laser pulses form a nanoplasma by avalanche-like electron impact ionizations (EIIs) even at lower laser intensities where He is not directly field ionized, provided that the droplets contain a few dopant atoms which provide seed electrons for the EII avalanche. In this theoretical paper on calcium and xenon doped He droplets we elucidate the mechanism which induces ionization avalanches, termed ignition. We find that the partial loss of seed electrons from the activated droplets starkly assists ignition, as the Coulomb barrier for ionization of helium is lowered by the electric field of the dopant cations, and this deshielding of the cation charges enhances their electric field. In addition, the dopant ions assist the acceleration of the seed electrons (slingshot effect) by the laser field, supporting EIIs of He and also causing electron loss by catapulting electrons away. The dopants’ ability to lower the Coulomb barriers at He as well as the slingshot effect decrease with the spatial expansion of the dopant, causing a dependence of the dopants’ ignition capability on the dopant mass. Here, we develop criteria (impact count functions) to assess the ignition capability of dopants, based on (i) the spatial overlap of the seed electron cloud with the He atoms and (ii) the overlap of their kinetic energy distribution with the distribution of Coulomb barrier heights at He. The relatively long time delays between the instants of dopant ionization and ignition (incubation times) for calcium doped droplets are determined to a large extent by the time it takes to deshield the dopant ions.

Non-metallic dopant modulation of conductivity in substoichiometric tantalum pentoxide: A first-principles study

Science.gov (United States)

Bondi, Robert J.; Fox, Brian P.; Marinella, Matthew J.

2017-06-01

We apply density-functional theory calculations to predict dopant modulation of electrical conductivity (σo) for seven dopants (C, Si, Ge, H, F, N, and B) sampled at 18 quantum molecular dynamics configurations of five independent insertion sites into two (high/low) baseline references of σo in amorphous Ta2O5, where each reference contains a single, neutral O vacancy center (VO0). From this statistical population (n = 1260), we analyze defect levels, physical structure, and valence charge distributions to characterize nanoscale modification of the atomistic structure in local dopant neighborhoods. C is the most effective dopant at lowering Ta2Ox σo, while also exhibiting an amphoteric doping behavior by either donating or accepting charge depending on the host oxide matrix. Both B and F robustly increase Ta2Ox σo, although F does so through elimination of Ta high charge outliers, while B insertion conversely creates high charge O outliers through favorable BO3 group formation, especially in the low σo reference. While N applications to dope and passivate oxides are prevalent, we found that N exacerbates the stochasticity of σo we sought to mitigate; sensitivity to the N insertion site and some propensity to form N-O bond chemistries appear responsible. We use direct first-principles predictions of σo to explore feasible Ta2O5 dopants to engineer improved oxides with lower variance and greater repeatability to advance the manufacturability of resistive memory technologies.

Study of Liquid Argon Dopants for LHC Hadron Calorimetry

CERN Multimedia

2002-01-01

Hadron calorimetry based on the Liquid Argon Ionisation Chamber technique is one of the choice techniques for LHC-experimentation. A systematic study of the effect of selected dopants on Liquid Argon (LAr) will be carried out with the aim to achieve an improvement on: \\item (i)~``Fast Liquid Argon'' search and study of dopants to increase the drift velocity. It has been already shown that CH&sub4. added at a fraction of one percent increases the drift velocity by a factor of two or more. \\item (ii)~``Compensated Liquid Argon'' search and study of dopants to increase the response to densely ionising particles, resulting in improved compensation, such as photosensitive dopants. \\end{enumerate}\\\\ \\\\ Monitoring of the parameters involved in understanding the response of a calorimeter is essential. In case of doped LAr, the charge yield, the non-saturated drift velocity and the electron lifetime in the liquid should be precisely and simultaneously monitored as they all vary with the level of dopant concentrati...

Charge separation technique for metal-oxide-silicon capacitors in the presence of hydrogen deactivated dopants

International Nuclear Information System (INIS)

Witczak, Steven C.; Winokur, Peter S.; Lacoe, Ronald C.; Mayer, Donald C.

2000-01-01

An improved charge separation technique for metal-oxide-silicon (MOS) capacitors is presented which accounts for the deactivation of substrate dopants by hydrogen at elevated irradiation temperatures or small irradiation biases. Using high-frequency capacitance-voltage (C-V) measurements, radiation-induced inversion voltage shifts are separated into components due to oxide trapped charge, interface traps and deactivated dopants, where the latter is computed from a reduction in Si capacitance. In the limit of no radiation-induced dopant deactivation, this approach reduces to the standard midgap charge separation technique used widely for the analysis of room-temperature irradiations. The technique is demonstrated on a p-type MOS capacitor irradiated with 60 Co γ-rays at 100 C and zero bias, where the dopant deactivation is significant

Defect evolution and dopant activation in laser annealed Si and Ge

DEFF Research Database (Denmark)

Cristiano, F.; Shayesteh, M.; Duffy, R.

2016-01-01

Defect evolution and dopant activation are intimately related to the use of ion implantation and annealing, traditionally used to dope semiconductors during device fabrication. Ultra-fast laser thermal annealing (LTA) is one of the most promising solutions for the achievement of abrupt and highly...... doped junctions. In this paper, we report some recent investigations focused on this annealing method, with particular emphasis on the investigation of the formation and evolution of implant/anneal induced defects and their impact on dopant activation. In the case of laser annealed Silicon, we show...

Effects of co-dopants on the magnetic properties of Ni–Zn ferrites

Energy Technology Data Exchange (ETDEWEB)

Wang, Sea-Fue, E-mail: sfwang@ntut.edu.tw; Hsu, Yung-Fu; Chou, Kai-Mou; Tsai, Jeng-Ting

2015-01-15

In this study, substitution of co-dopants into the Ni{sub 0.4}Zn{sub 0.6}Fe{sub 2}O{sub 4} ceramic was performed. Al{sup 3+}, Sn{sup 4+} and Ti{sup 4+} ions were added to the Ni{sub 0.4}Zn{sub 0.4}Li{sub 0.10}Fe{sub 2.10}O{sub 4} ceramic to improve magnetic properties. After sintering, all samples were indexed on a spinel structure and no detectable second phase was observed. When the concentration of dopants increased, the grain size of the Ni–Zn ferrites increased from 1.40 to 6.05 μm and the saturation magnetization declined from 428.8 emu/cm{sup 3} to 374.0 emu/cm{sup 3}. Amongst the systems investigated, the Ni{sub 0.4}Zn{sub 0.4}Li{sub 0.10}Al{sub 0.050}Fe{sub 2.050}O{sub 4}, Ni{sub 0.4}Zn{sub 0.425}Li{sub 0.10}Ti{sub 0.025}Fe{sub 2.050}O{sub 4}, and Ni{sub 0.4}Zn{sub 0.450}Li{sub 0.10}Ti{sub 0.050}Fe{sub 2.000}O{sub 4} ceramics revealed promising magnetic properties for applications. The measured initial permeability and quality factor were respectively 291.9 and 45.1 for the Ni{sub 0.4}Zn{sub 0.4}Li{sub 0.10}Al{sub 0.050}Fe{sub 2.050}O{sub 4} ceramic, 316.9 and 42.5 for the Ni{sub 0.4}Zn{sub 0.425}Li{sub 0.10}Ti{sub 0.025}Fe{sub 2.050}O{sub 4} ceramic, 429.4 and 34.8 for the Ni{sub 0.4}Zn{sub 0.450}Li{sub 0.10}Ti{sub 0.050}Fe{sub 2.000}O{sub 4} ceramic. The high initial permeability and quality factor values associated with good electrical resistivity (>10{sup 6} Ω-cm) qualify the ceramics for high frequency applications. - Highlights: • Co-dopants Al{sup 3+}–Li{sup +}, Sn{sup 4+}–Li{sup +}, and Ti{sup 4}–Li{sup +} were substituted into Ni–Zn lattices. • Grain size of Ni–Zn ferrites grew from 1.40 to 6.05 μm with rising dopants content. • Saturation magnetization declined from 428.8 to 374.0 emu/cm{sup 3} with adding dopants. • Ni{sub 0.4}Zn{sub 0.4}Li{sub 0.10}Al{sub 0.050}Fe{sub 2.050}O{sub 4} ceramic showed an μ{sub i} of 291.9 and a Q{sub f} of 45.1.

Chromium 51 em K2CrO4: reactions of dopant atoms in solid state

International Nuclear Information System (INIS)

Valim, J.B.; Nascimento, R.L.G. do; Collins, C.H.; Collins, K.E.

1986-01-01

The study of the chemistry of 'dopant' 51 Cr(III) atoms in crystalline Cr(VI) compounds began as a sub-field of Hot Atom Chemistry. We shall review the attempts to use 'dopant' chromium-51 atoms as surrogate chromium recoil atoms with the special property of having a low-energy, recoil-dam-age-free history. These dopant atoms have shown behaviors very similar to those of high energy recoil 51 Gr atoms, thus offering little hope of learning about special damage site structures and reactions by behavioral differences. Recent work has shown that at least some of the 'dopant' 51 Cr(III) is present as a second, non-chromate solid phase in 'doped crystal' experiments. Monodisperse 51 Cr(OH) 3 particles mixed with pure K 2 CrO 4 are very reactive. (Author) [pt

Metalorganic chemical vapor deposition of ZnO:N using NO as dopant

International Nuclear Information System (INIS)

Dangbegnon, J.K.; Talla, K.; Roro, K.T.; Botha, J.R.

2009-01-01

Highly c-axis orientated ZnO was grown by metal organic chemical vapor deposition (MOCVD) using NO as both oxidant and nitrogen dopant source. The properties of the deposited material are investigated by X-ray diffraction to study the crystalline quality of the thin films. Photoluminescence measurements are used to determine the optical properties of the material as a function of VI/II ratio and post growth-annealing temperature. Two transitions appear at 3.228 and 3.156 eV and are interpreted as involving active nitrogen acceptors. An increase in the NO flow increases the concentration of nitrogen in the films, which are activated by subsequent annealing at 600 deg. C in an oxygen ambient.

Metalorganic chemical vapor deposition of ZnO:N using NO as dopant

Energy Technology Data Exchange (ETDEWEB)

Dangbegnon, J.K., E-mail: JulienKouadio.Dangbegnon@nmmu.ac.z [Department of Physics, PO Box 77000, Nelson Mandela Metropolitan University, Port Elizabeth (South Africa); Talla, K.; Roro, K.T.; Botha, J.R. [Department of Physics, PO Box 77000, Nelson Mandela Metropolitan University, Port Elizabeth (South Africa)

2009-12-01

Highly c-axis orientated ZnO was grown by metal organic chemical vapor deposition (MOCVD) using NO as both oxidant and nitrogen dopant source. The properties of the deposited material are investigated by X-ray diffraction to study the crystalline quality of the thin films. Photoluminescence measurements are used to determine the optical properties of the material as a function of VI/II ratio and post growth-annealing temperature. Two transitions appear at 3.228 and 3.156 eV and are interpreted as involving active nitrogen acceptors. An increase in the NO flow increases the concentration of nitrogen in the films, which are activated by subsequent annealing at 600 deg. C in an oxygen ambient.

Two-dimensional dopant profiling by electrostatic force microscopy using carbon nanotube modified cantilevers

International Nuclear Information System (INIS)

Chin, S.-C.; Chang, Y.-C.; Chang, C.-S.; Tsong, T T; Hsu, Chen-Chih; Wu, Chih-I; Lin, W-H; Woon, W-Y; Lin, L-T; Tao, H-J

2008-01-01

A two-dimensional (2D) dopant profiling technique is demonstrated in this work. We apply a unique cantilever probe in electrostatic force microscopy (EFM) modified by the attachment of a multiwalled carbon nanotube (MWNT). Furthermore, the tip apex of the MWNT was trimmed to the sharpness of a single-walled carbon nanotube (SWNT). This ultra-sharp MWNT tip helps us to resolve dopant features to within 10 nm in air, which approaches the resolution achieved by ultra-high vacuum scanning tunnelling microscopy (UHV STM). In this study, the CNT-probed EFM is used to profile 2D buried dopant distribution under a nano-scale device structure and shows the feasibility of device characterization for sub-45 nm complementary metal-oxide-semiconductor (CMOS) field-effect transistors

Application of dopant-free hole transport materials for perovskite solar cells

International Nuclear Information System (INIS)

Franckevincius, M.; Gulbinas, V.; Gratzel, M.; Zakeeruddin, S.; Pauerle, P.; Mishra, A.; Steck, C.

2015-01-01

In this work we present the synthesis, characterization and application of a series of additive and dopant free hole transport materials (HTM) for solid-state perovskite-based solar cells. Newly synthesized HTMs showed strong absorption in the visible spectral range and suitable HOMO-LUMO energy levels for the application for methylammonium lead(II) iodide (CH_3NH_3PbI_3) perovskite. Dopant-free perovskite solar cells have been fabricated using CH_3NH_3PbI_3 perovskite and the newly synthesized HTMs following sequential deposition method, which allows us to reach power conversion efficiencies as high as 11.4 %. The easy of synthesis, low cost and relatively high performance of newly synthesized HTMs has great prospects for commercial applications in the near-future. (authors)

The Impact of Dopant Segregation on the Maximum Carrier Density in Si:P Multilayers.

Science.gov (United States)

Keizer, Joris G; McKibbin, Sarah R; Simmons, Michelle Y

2015-07-28

Abrupt dopant profiles and low resistivity are highly sought after qualities in the silicon microelectronics industry and, more recently, in the development of an all epitaxial Si:P based quantum computer. If we increase the active carrier density in silicon to the point where the material becomes superconducting, while maintaining a low thermal budget, it will be possible to fabricate nanoscale superconducting devices using the highly successful technique of depassivation lithography. In this work, we investigate the dopant profile and activation in multiple high density Si:P δ-layers fabricated by stacking individual layers with intervening silicon growth. We determine that dopant activation is ultimately limited by the formation of P-P dimers due to the segregation of dopants between multilayers. By increasing the encapsulation thickness between subsequent layers, thereby minimizing the formation of these deactivating defects, we are able to achieve an active carrier density of ns = 4.5 ×10(14) cm(-2) for a triple layer. The results of electrical characterization are combined with those of secondary ion mass spectroscopy to construct a model that accurately describes the impact of P segregation on the final active carrier density in Si:P multilayers. Our model predicts that a 3D active carrier density of 8.5 × 10(20) cm(-3) (1.7 atom %) can be achieved.

High-efficiency concentrator silicon solar cells

Energy Technology Data Exchange (ETDEWEB)

Sinton, R.A.; Cuevas, A.; King, R.R.; Swanson, R.M. (Stanford Univ., CA (USA). Solid-State Electronics Lab.)

1990-11-01

This report presents results from extensive process development in high-efficiency Si solar cells. An advanced design for a 1.56-cm{sup 2} cell with front grids achieved 26% efficiency at 90 suns. This is especially significant since this cell does not require a prismatic cover glass. New designs for simplified backside-contact solar cells were advanced from a status of near-nonfunctionality to demonstrated 21--22% for one-sun cells in sizes up to 37.5 cm{sup 2}. An efficiency of 26% was achieved for similar 0.64-cm{sup 2} concentrator cells at 150 suns. More fundamental work on dopant-diffused regions is also presented here. The recombination vs. various process and physical parameters was studied in detail for boron and phosphorous diffusions. Emitter-design studies based solidly upon these new data indicate the performance vs design parameters for a variety of the cases of most interest to solar cell designers. Extractions of p-type bandgap narrowing and the surface recombination for p- and n-type regions from these studies have a generality that extends beyond solar cells into basic device modeling. 68 refs., 50 figs.

Three-dimensional analysis of Eu dopant atoms in Ca-α-SiAlON via through-focus HAADF-STEM imaging

Energy Technology Data Exchange (ETDEWEB)

Saito, Genki, E-mail: genki@eng.hokudai.ac.jp; Yamaki, Fuuta; Kunisada, Yuji; Sakaguchi, Norihito; Akiyama, Tomohiro

2017-04-15

Highlights: • Through-focus HAADF-STEM imaging was studied. • Spatial distribution of Eu atoms in Ca-α-SiAlON was analyzed. • A large convergence semi-angle increased the depth resolution. • The radial distribution function of Eu dopants was analyzed. - Abstract: Three-dimensional (3D) distributional analysis of individual dopant atoms in materials is important to development of optical, electronic, and magnetic materials. In this study, we adopted through-focus high-angle annular dark-field (HAADF) imaging for 3D distributional analysis of Eu dopant atoms in Ca-α-SiAlON phosphors. In this context, the effects of convergence semi-angle and Eu z-position on the HAADF image contrast were investigated. Multi-slice image simulation revealed that the contrast of the dopant site was sensitive to change of the defocus level. When the defocus level matched the depth position of a Eu atom, the contrast intensity was significantly increased. The large convergence semi-angle greatly increased the depth resolution because the electron beam tends spread instead of channeling along the atomic columns. Through-focus HAADF-STEM imaging was used to analyze the Eu atom distribution surrounding 10 nm cubes with defocus steps of 0.68 nm each. The contrast depth profile recorded with a narrow step width clearly analyzed the possible depth positions of Eu atoms. The radial distribution function obtained for the Eu dopants was analyzed using an atomic distribution model that was based on the assumption of random distribution. The result suggested that the Ca concentration did not affect the Eu distribution. The decreased fraction of neighboring Eu atoms along z-direction might be caused by the enhanced short-range Coulomb-like repulsive forces along the z-direction.

Ti-dopant-enhanced photocatalytic activity of a CaFe{sub 2}O{sub 4}/MgFe{sub 2}O{sub 4} bulk heterojunction under visible-light irradiation

Energy Technology Data Exchange (ETDEWEB)

Borse, Pramod H. [International Advanced Research Center for Powder Metallurgy and New Materials, Hyderabad (India); Kim, Jae Y.; Lee, Jae S. [Pohang University of Science and Technology, Pohang (Korea, Republic of); Lim, Kwon T. [Pukyong National University, Busan (Korea, Republic of); Jeong, Euh D.; Bae, Jong S.; Yoon, Jang H.; Yu, Seong M.; Kim, Hyun G. [Korea Basic Science Institute, Busan (Korea, Republic of)

2012-07-15

The effect substitution of Ti{sup 4+} at the Fe{sup 3+} site in a CaFe{sub 2}O{sub 4{sup -}}MgFe{sub 2}O{sub 4} bulk hetero-junction (BH) lattice photocatalyst was explored and the Ti ion concentration was optimized to fabricate an efficient photocatalyst. A BH consisting of an optimum dopant concentration (Ti{sup +4}) level of x = 0.03 exhibited an increased band gap and generated a 1.5 times higher photocurrent. The newly fabricated Ti ion doped photocatalyst showed an enhanced quantum yield (up to ∼13.3%) for photodecomposition of a H{sub 2}O-CH{sub 3}OH mixture, as compared to its undoped BH counterpart under visible light (λ ≥ 420 nm). In contrast, the material doped with a very high Ti-dopant concentration displayed deteriorated photochemical properties. An efficient charge-separation induced by Ti-ion doping seems to be responsible for the higher photocatalytic activity in a doped bulk BH.

Transport in Silicon Nanowires: Role of Radial Dopant Profile

DEFF Research Database (Denmark)

Markussen, Troels; Rurali, Riccardo; Jauho, Antti-Pekka

2008-01-01

distributions of P dopant impurities. We find that the radial distribution of the dopants influences the conductance properties significantly: surface doped wires have longer mean-free paths and smaller sample-to-sample fluctuations in the cross-over from ballistic to diffusive transport. These findings can...

Sc and Nb Dopants in SrCoO3 Modulate Electronic and Vacancy Structures for Improved Water Splitting and SOFC Cathodes

KAUST Repository

Tahini, Hassan A.; Tan, Xin; Zhou, Wei; Zhu, Zhonghua; Schwingenschlö gl, Udo; Smith, Sean C.

2017-01-01

SrCoO3 is a promising material in the field of electrocatalysis. Difficulties in synthesising the material in its cubic phase have been overcome by doping it with Sc and Nb ions [Mater. Horiz.2015, 2, 495–501]. Using ab initio calculations and special quasi random structures we undertake a systematic study of these dopants in order to elucidate the effect of doping on electronic structure of the SrCoO3 host and the formation of oxygen vacancies. We find that while the overall electronic structure of SrCoO3 is preserved, increasing the Sc fraction leads to a decrease of electrical conductivity, in agreement with earlier experimental work. For low Sc and Nb doping fractions we find that the oxygen vacancy formation increases relative to undoped SrCoO3. However, as the dopants concentration is increased the vacancy formation energy drops significantly, indicating a strong tendency to accommodate high concentration of oxygen vacancies and hence non-stoichiometry. This is explained based on the electronic instabilities caused by the presence of Sc ions which weakens the B-O interactions as well as the increased degree of electron delocalization on the oxygen sublattice. Sc dopants also shift the p-band centre closer to the Fermi level, which can be associated with experimentally reported improvements in oxygen evolution reactions. These findings provide crucial baseline information for the design of better electrocatalysts for oxygen evolution reactions as well as fuel-cell cathode materials.

Sc and Nb Dopants in SrCoO3 Modulate Electronic and Vacancy Structures for Improved Water Splitting and SOFC Cathodes

KAUST Repository

Tahini, Hassan A.

2017-01-12

SrCoO3 is a promising material in the field of electrocatalysis. Difficulties in synthesising the material in its cubic phase have been overcome by doping it with Sc and Nb ions [Mater. Horiz.2015, 2, 495–501]. Using ab initio calculations and special quasi random structures we undertake a systematic study of these dopants in order to elucidate the effect of doping on electronic structure of the SrCoO3 host and the formation of oxygen vacancies. We find that while the overall electronic structure of SrCoO3 is preserved, increasing the Sc fraction leads to a decrease of electrical conductivity, in agreement with earlier experimental work. For low Sc and Nb doping fractions we find that the oxygen vacancy formation increases relative to undoped SrCoO3. However, as the dopants concentration is increased the vacancy formation energy drops significantly, indicating a strong tendency to accommodate high concentration of oxygen vacancies and hence non-stoichiometry. This is explained based on the electronic instabilities caused by the presence of Sc ions which weakens the B-O interactions as well as the increased degree of electron delocalization on the oxygen sublattice. Sc dopants also shift the p-band centre closer to the Fermi level, which can be associated with experimentally reported improvements in oxygen evolution reactions. These findings provide crucial baseline information for the design of better electrocatalysts for oxygen evolution reactions as well as fuel-cell cathode materials.

Microwave modulation characteristics of twisted liquid crystals with chiral dopant

Directory of Open Access Journals (Sweden)

Rui Yuan

2017-01-01

Full Text Available Adding a chiral dopant in twisted nematic (TN liquid crystal cell can stabilize the orientation of liquid crystal molecules, particularly in high TN (HTN or super TN (STN liquid crystal cells. The difference in pitches in liquid crystal is induced by the chiral dopant, and these different pitches affect the orientation of liquid crystal director under an external applied voltage and influence the characteristics of microwave modulation. To illustrate this point, the microwave phase shift per unit length (MPSL versus voltage is calculated on the basis of the elastic theory of liquid crystal and the finite-difference iterative method. Enhancing the pitch induced by the chiral dopant in liquid crystal increases the MPSLs, but the stability of the twisted structures is decreased. Thus, appropriate pitches of 100d, 4d, and 2d can be applied in TN, HTN, and STN cells with cell gap d to enhance the characteristics of microwave modulation and stabilize the structures in twisted cell. This method can improve the characteristics of liquid crystal microwave modulators such that the operating voltage and the size of such phase shifters can be decreased.

Interplay of dopants and defects in making Cu doped TiO{sub 2} nanoparticle a ferromagnetic semiconductor

Energy Technology Data Exchange (ETDEWEB)

Choudhury, Biswajit, E-mail: biswa.tezu@gmail.com [Department of Physics, Tezpur University, Napaam 784028, Assam (India); Choudhury, Amarjyoti [Department of Physics, Tezpur University, Napaam 784028, Assam (India); Borah, Debajit [Department of Chemical Engineering, Indian Institute of Technology Guwahati, Guwahati 781039, Assam (India)

2015-10-15

Here we have studied the role of oxygen defects and Cu dopants on ferromagnetism in Cu doped TiO{sub 2} nanoparticles with nominal Cu concentration of 2%, 4% and 6 mol%. Electron paramagnetic resonance (EPR) spectra analysis reveals the presence of Cu{sup 2+} in the distorted octahedral coordination of TiO{sub 2}. Cu d-states undergo strong p-d coupling with the valence band O 2p state of TiO{sub 2} resulting the extended absorption hump in the visible region. Photoluminescence results reveal the presence of oxygen defect related emission peaks in Cu doped TiO{sub 2}. Room temperature ferromagnetism is observed in all the Cu doped TiO{sub 2} nanoparticles. Saturation magnetization is the highest at 4 mol% and then there is a decrease in magnetization at 6 mol%. Ferromagnetism completely disappears on calcinations of 4% Cu doped TiO{sub 2} in air at 450 °C for 8 h. It is speculated that both oxygen vacancies and Cu d-states are involved in the room temperature ferromagnetism. Spin polarization occurs by the formation of bound magnetic polaron between electrons in Cu{sup 2+}d-states and the unpaired spins in oxygen vacancies. Presence of Cu{sup 2+}-Cu{sup 2+}d-d exchange interaction and Cu{sup 2+}-O{sup 2−}-Cu{sup 2+} antiferromagnetic superexchange interactions might have resulted in the reduction in magnetization at 6 mol% Cu. - Graphical abstract: Ferromagnetism in Cu doped TiO{sub 2} requires presence of both Cu dopant and oxygen vacancies. - Highlights: • Cu doped TiO{sub 2} nanoparticle displays room temperature ferromagnetism. • Ferromagnetism requires presence of both Cu and oxygen vacancies. • Antiferromagnetic interaction persists at high Cu dopant concentration. • Paramagnetism appears on air annealing of the doped system for longer period.

Chemical and Electrochemical Synthesis of Polypyrrole Using Carrageenan as a Dopant: Polypyrrole/Multi-Walled Carbon Nanotube Nanocomposites

Directory of Open Access Journals (Sweden)

Mostafizur Rahaman

2018-06-01

Full Text Available In this article, iota-carrageenan (IC and kappa-carrageenan (KC are used as dopants for the chemical and electrochemical synthesis of polypyrrole (PPy. The composites of chemically synthesized PPy with multi-walled carbon nanotubes (MWNTs were prepared using an in situ technique. Both the dialyzed and non-dialyzed IC and KC were used as dopants for electrochemical polymerization of pyrrole. Chemically synthesized PPy and PPy/MWNTs composites were studied by ultraviolet visible (UV-vis absorption spectra to investigate the effect of the concentration and the incorporation of MWNTs. In addition, the electrical, thermal, mechanical, and microscopic characterizations of these films were performed to examine the effect of the dopants and MWNTs on these properties, along with their surface morphology. The films of electrochemically polymerized PPy were characterized using UV-vis absorption spectra, scanning electron microscopy, and cyclic voltammetry (CV. The results were then compared with the chemical polymerized PPy.

Influence of nitrogen dopants on N-doped TiO2 electrodes and their applications in dye-sensitized solar cells

International Nuclear Information System (INIS)

Guo Wei; Shen Yihua; Boschloo, Gerrit; Hagfeldt, Anders; Ma Tingli

2011-01-01

Highlights: → Three different types of nanocrystalline N-doped TiO 2 synthesized by several nitrogen dopants. → N-doped DSCs achieves a high conversion efficiency of 8.32%. → Ammonia acts as good nitrogen dopants. → Enhanced photocurrent of ca. 36% in N-doped DSCs. → Less charge are needed to get a high open-circuit voltage in N-doped films. - Abstract: Three different types of nanocrystalline, N-doped TiO 2 electrodes were synthesized using several nitrogen dopants through wet methods. The obtained nanocrystalline, N-doped TiO 2 electrodes possessed different crystallite sizes, surface areas, and N-doping amounts. Characterizations were performed to reveal the nitrogen-doping processes for the wet methods using ammonia, urea, and triethylamine as the nitrogen dopants. Additionally, a high conversion efficiency of 8.32% was achieved by the dye-sensitized solar cells, based on the N-doped TiO 2 electrodes. For instance, in comparison with the commercial P25 (5.76%) and pure anatase TiO 2 electrodes (7.14%), significant improvements (44% and 17%, respectively) in the efficiencies were obtained. The findings also indicated that the ammonia nitrogen dopant was more efficient than other two nitrogen dopants. The electron transports, electron lifetimes, and charge recombination in the dye-sensitized N-doped TiO 2 solar cells also differed from those in the pure TiO 2 -based dye-sensitized solar cells (DSCs). Specifically, an enhanced photocurrent of ca. 36% in N-doped DSCs resulted from the synergistic effects of the high dye uptake and the efficient electron transport. Moreover, the relationship between charge and voltage revealed that less charge was needed to get a high open-circuit voltage in the N-doping films.

Influence of Mn-dopant on the properties of α-FeOOH particles precipitated in highly alkaline media

International Nuclear Information System (INIS)

Krehula, Stjepko; Music, Svetozar

2006-01-01

The effects of Mn-dopant on the formation of solid solutions α-(Fe, Mn)OOH in dependence on the initial concentration ratio r = [Mn]/([Mn] + [Fe]), as well as on the size and morphology of the corresponding particles were investigated using Moessbauer and FT-IR spectroscopies, high-resolution scanning electron microscopy (FE SEM) and an energy dispersive X-ray analyser (EDS). The value of the hyperfine magnetic field of 34.9 T, as recorded for the reference α-FeOOH sample at RT, decreased linearly up to 21.4 T for sample with r = 0.1667. Only a paramagnetic doublet at RT was recorded for sample with r = 0.2308, a ferrite phase was additionally found for r = 0.3333. Fe-OH bending IR bands, δ OH and γ OH , were influenced by the Mn-substitution as manifested through their gradual shifts. FE SEM micrographs showed a great elongation of the starting acicular particles along the c-axis with an increase in Mn-doping. For r = 0.1667 and 0.2308 star-shaped and dendritic twin α-(Fe, Mn)OOH particles were observed. The length of these α-(Fe, Mn)OOH particles decreased, whereas their width increased. The α-Fe 2 O 3 phase was not detected in any of the samples prepared

Computational Study of Nb-Doped-SnO₂/Pt Interfaces: Dopant Segregation, Electronic Transport, and Catalytic Properties

DEFF Research Database (Denmark)

Fu, Qiang; Halck, Niels Bendtsen; Hansen, Heine Anton

2017-01-01

functional theory and non equilibrium Green's function study, we investigate the Nb segregation at Pt/NTO interfaces under operational electrochemical conditions, and reveal the resulting effects on the electronic transport, as well as the catalytic properties. We find that the Nb dopants tend to aggregate......Carbon black, a state-of-the-art cathode material for proton exchange membrane fuel cells (PEMFCs), suffers from severe corrosion in practical applications. Niobium-doped tin dioxide (NTO) is a promising alternative to support the Pt catalysts at the cathodes. Here, through a combined density....... The electronic conductivities of the Pt/NTO systems are not particularly sensitive to the distance of the Nb dopants relative to the interface, but depend explicitly on the Nb concentration and configuration. Through a dopant induced ligand effect, the NTO substrates can improve the catalytic activity of the Pt...

Reaction of N,N'-dimethylformamide and divalent viologen molecule to generate an organic dopant for molybdenum disulfide

Science.gov (United States)

Fukui, A.; Miura, K.; Ichimiya, H.; Tsurusaki, A.; Kariya, K.; Yoshimura, T.; Ashida, A.; Fujimura, N.; Kiriya, D.

2018-05-01

Tuning the carrier concentration is essential for semiconducting materials to apply optoelectronic devices. Molybdenum disulfide (MoS2) is a semiconducting material composed of atomically thin (˜0.7 nm thickness) layers. To dope thin MoS2, instead of using conventional atom/ion injection processes, a surface charge transfer method was successfully applied. In this study, we report a simple preparation method of a molecular dopant applicable to the doping process. The method follows a previous report for producing a molecular dopant, benzyl viologen (BV) which shows electron doping to MoS2. To prepare dopant BV molecules, a reduction process with a commercially available divalent BV by sodium borohydride (NaBH4) is required; however, the reaction requires a large consumption of NaBH4. NaBH4 drastically reacts with the solvent water itself. We found a reaction process of BV in an organic solvent, N,N'-dimethylformamide (DMF), by adding a small amount of water dissolving the divalent BV. The reaction is mild (at room temperature) and is autonomous once DMF comes into contact with the divalent BV aqueous solution. The reaction can be monitored with a UV-Vis spectrometer, and kinetic analysis indicates two reaction steps between divalent/monovalent/neutral viologen isomers. The product was soluble in toluene and did not dissolve in water, indicating it is similar to the reported dopant BV. The synthesized molecule was found to act as a dopant for MoS2 by applying a metal-oxide-semiconductor field-effect-transistor (MOSFET) structure. The process is a general method and applicable to other viologen-related dopants to tune the electronic structure of 2D materials to facilitate generating atomically thin devices.

Reaction of N,N’-dimethylformamide and divalent viologen molecule to generate an organic dopant for molybdenum disulfide

Directory of Open Access Journals (Sweden)

A. Fukui

2018-05-01

Full Text Available Tuning the carrier concentration is essential for semiconducting materials to apply optoelectronic devices. Molybdenum disulfide (MoS2 is a semiconducting material composed of atomically thin (∼0.7 nm thickness layers. To dope thin MoS2, instead of using conventional atom/ion injection processes, a surface charge transfer method was successfully applied. In this study, we report a simple preparation method of a molecular dopant applicable to the doping process. The method follows a previous report for producing a molecular dopant, benzyl viologen (BV which shows electron doping to MoS2. To prepare dopant BV molecules, a reduction process with a commercially available divalent BV by sodium borohydride (NaBH4 is required; however, the reaction requires a large consumption of NaBH4. NaBH4 drastically reacts with the solvent water itself. We found a reaction process of BV in an organic solvent, N,N’-dimethylformamide (DMF, by adding a small amount of water dissolving the divalent BV. The reaction is mild (at room temperature and is autonomous once DMF comes into contact with the divalent BV aqueous solution. The reaction can be monitored with a UV-Vis spectrometer, and kinetic analysis indicates two reaction steps between divalent/monovalent/neutral viologen isomers. The product was soluble in toluene and did not dissolve in water, indicating it is similar to the reported dopant BV. The synthesized molecule was found to act as a dopant for MoS2 by applying a metal-oxide-semiconductor field-effect-transistor (MOSFET structure. The process is a general method and applicable to other viologen-related dopants to tune the electronic structure of 2D materials to facilitate generating atomically thin devices.

A reliable method for the counting and control of single ions for single-dopant controlled devices

International Nuclear Information System (INIS)

Shinada, T; Kurosawa, T; Nakayama, H; Zhu, Y; Hori, M; Ohdomari, I

2008-01-01

By 2016, transistor device size will be just 10 nm. However, a transistor that is doped at a typical concentration of 10 18 atoms cm -3 has only one dopant atom in the active channel region. Therefore, it can be predicted that conventional doping methods such as ion implantation and thermal diffusion will not be available ten years from now. We have been developing a single-ion implantation (SII) method that enables us to implant dopant ions one-by-one into semiconductors until the desired number is reached. Here we report a simple but reliable method to control the number of single-dopant atoms by detecting the change in drain current induced by single-ion implantation. The drain current decreases in a stepwise fashion as a result of the clusters of displaced Si atoms created by every single-ion incidence. This result indicates that the single-ion detection method we have developed is capable of detecting single-ion incidence with 100% efficiency. Our method potentially could pave the way to future single-atom devices, including a solid-state quantum computer

Dopant profile engineering of advanced Si MOSFET's using ion implantation

International Nuclear Information System (INIS)

Stolk, P.A.; Ponomarev, Y.V.; Schmitz, J.; Brandenburg, A.C.M.C. van; Roes, R.; Montree, A.H.; Woerlee, P.H.

1999-01-01

Ion implantation has been used to realize non-uniform, steep retrograde (SR) dopant profiles in the active channel region of advanced Si MOSFET's. After defining the transistor configuration, SR profiles were formed by dopant implantation through the polycrystalline Si gate and the gate oxide (through-the-gate, TG, implantation). The steep nature of the as-implanted profile was retained by applying rapid thermal annealing for dopant activation and implantation damage removal. For NMOS transistors, TG implantation of B yields improved transistor performance through increased carrier mobility, reduced junction capacitances, and reduced susceptibility to short-channel effects. Electrical measurements show that the gate oxide quality is not deteriorated by the ion-induced damage, demonstrating that transistor reliability is preserved. For PMOS transistors, TG implantation of P or As leads to unacceptable source/drain junction broadening as a result of transient enhanced dopant diffusion during thermal activation

Hard-Wired Dopant Networks and the Prediction of High Transition Temperatures in Ceramic Superconductors

International Nuclear Information System (INIS)

Phillips, J.C.

2010-01-01

The review multiple successes of the discrete hard-wired dopant network model ZZIP, and comment on the equally numerous failures of continuum models, in describing and predicting the properties of ceramic superconductors. The prediction of transition temperatures can be regarded in several ways, either as an exacting test of theory, or as a tool for identifying theoretical rules for defining new homology models. Popular first principle methods for predicting transition temperatures in conventional crystalline superconductors have failed for cuprate HTSC, as have parameterized models based on CuO2 planes (with or without apical oxygen). Following a path suggested by Bayesian probability, it was found that the glassy, self-organized dopant network percolative model is so successful that it defines a new homology class appropriate to ceramic superconductors. The reasons for this success in an exponentially complex (non-polynomial complete, NPC) problem are discussed, and a critical comparison is made with previous polynomial (PC) theories. The predictions are successful for the superfamily of all ceramics, including new non-cuprates based on FeAs in place of CuO2.

Nucleophilic Aromatic Substitution Between Halogenated Benzene Dopants and Nucleophiles in Atmospheric Pressure Photoionization.

Science.gov (United States)

Kauppila, Tiina J; Haack, Alexander; Kroll, Kai; Kersten, Hendrik; Benter, Thorsten

2016-03-01

In a preceding work with dopant assisted-atmospheric pressure photoionization (DA-APPI), an abundant ion at [M + 77](+) was observed in the spectra of pyridine and quinoline with chlorobenzene dopant. This contribution aims to reveal the identity and route of formation of this species, and to systematically investigate structurally related analytes and dopants. Compounds containing N-, O-, and S-lone pairs were investigated with APPI in the presence of fluoro-, chloro-, bromo-, and iodobenzene dopants. Computational calculations on a density functional theory (DFT) level were carried out to study the reaction mechanism for pyridine and the different halobenzenes. The experimental and computational results indicated that the [M + 77](+) ion was formed by nucleophilic aromatic ipso-substitution between the halobenzene radical cation and nucleophilic analytes. The reaction was most efficient for N-heteroaromatic compounds, and it was weakened by sterical effects and enhanced by resonance stabilization. The reaction was most efficient with chloro-, bromo-, and iodobenzenes, whereas with fluorobenzene the reaction was scarcely observed. The calculated Gibbs free energies for the reaction between pyridine and the halobenzenes were shown to increase in the order I < Br < Cl < F. The reaction was found endergonic for fluorobenzene due to the strong C-F bonding, and exergonic for the other halobenzenes. For fluoro- and chlorobenzenes the reaction was shown to proceed through an intermediate state corresponding to [M + dopant](+), which was highly stable for fluorobenzene. For the bulkier bromine and iodine, this intermediate did not exist, but the halogens were shown to detach already during the approach by the nucleophile.

Influence of Ag doping concentration on structural and optical properties of CdS thin film

International Nuclear Information System (INIS)

Kumar, Pragati; Saxena, Nupur; Gupta, Vinay; Agarwal, Avinash

2015-01-01

This work shows the influence of Ag concentration on structural properties of pulsed laser deposited nanocrystalline CdS thin film. X-ray photoelectron spectroscopy (XPS) studies confirm the dopant concentration in CdS films and atomic concentration of elements. XPS studies show that the samples are slightly sulfur deficient. GAXRD scan reveals the structural phase transformation from cubic to hexagonal phase of CdS without appearance of any phase of CdO, Ag 2 O or Ag 2 S suggesting the substitutional doping of Ag ions. Photoluminescence studies illustrate that emission intensity increases with increase in dopant concentration upto 5% and then decreases for higher dopant concentration

Influence of Ag doping concentration on structural and optical properties of CdS thin film

Energy Technology Data Exchange (ETDEWEB)

Kumar, Pragati, E-mail: pkumar.phy@gmail.com [Department of Physics, Bareilly College, Bareilly, 243 005, Uttar Pradesh (India); Department of Physics and Astrophysics, University of Delhi, Delhi, 110 007 (India); Saxena, Nupur; Gupta, Vinay [Department of Physics and Astrophysics, University of Delhi, Delhi, 110 007 (India); Agarwal, Avinash [Department of Physics, Bareilly College, Bareilly, 243 005, Uttar Pradesh (India)

2015-05-15

This work shows the influence of Ag concentration on structural properties of pulsed laser deposited nanocrystalline CdS thin film. X-ray photoelectron spectroscopy (XPS) studies confirm the dopant concentration in CdS films and atomic concentration of elements. XPS studies show that the samples are slightly sulfur deficient. GAXRD scan reveals the structural phase transformation from cubic to hexagonal phase of CdS without appearance of any phase of CdO, Ag{sub 2}O or Ag{sub 2}S suggesting the substitutional doping of Ag ions. Photoluminescence studies illustrate that emission intensity increases with increase in dopant concentration upto 5% and then decreases for higher dopant concentration.

Metal (M) dopant centred local structures, high-pressure synthesis and bulk superconductivity in YBa sub 2 (Cu sub 1 sub - sub x M sub x) sub 3 O sub 7 sub - subdelta: M = Fe, Co, Ni

CERN Document Server

Shi, F; Bresser, W J; Boolchand, P; McDaniel, D

1997-01-01

Depression of T sub c by the dopants Fe or Co, but not Ni, is spectacularly reversed by synthesis of the titled cuprates at high P instead of ambient P of oxygen with T sub c enhanced from 32 to 82 K for M=Fe at x=0.10. With Fe dopant, Moessbauer spectroscopy reveals a conversion of a tetrahedral (A) into a trigonal bipyramidal coordinated (C) Fe chain site by oxygen addition in the chains upon high-P processing. The A->C site transformation is elucidated and extended to the case of Co dopant, and its consequences for superconducting behaviour discussed. (author). Letter-to-the-editor

Electroluminescence of organic light-emitting diodes with an ultra-thin layer of dopant

Energy Technology Data Exchange (ETDEWEB)

Li Weizhi [State Key Lab of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China); Yu Junsheng [State Key Lab of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China)], E-mail: jsyu@uestc.edu.cn; Wang, Tao [State Key Lab of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China); Jiang, Yadong [State Key Lab of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China)], E-mail: jiangyd@uestc.edu.cn; Wei, Bangxiong [State Key Lab of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China)

2008-03-15

Conventional fluorescent dyes, i.e., 4-(dicyanomethylene)-2-t-butyl-6(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB), 5,12-dihydro-5,12-dimethylquino [2,3-b]acridine-7,14-dione (DMQA) and 5,6,11,12-tetraphenylnaphthacene (Rubrene), were used to investigate the performance of organic light-emitting diodes (OLEDs) based on indium tin oxide (ITO)/N,N'-bis-(1-naphthyl)-N,N'-diphenyl-1,1'-biphenyl-4,4'-diamine (NPB)/tris-(8-hydroxyquinolate)-aluminum (Alq{sub 3})/MgAg. The dyes were either inserted into devices as an ultra-thin film at the NPB/Alq{sub 3} interface by sequential evaporation, or doped into the Alq{sub 3} emission layer by co-evaporation with the doping ratio about 2%. Electroluminescence (EL) spectra of devices indicated that concentration quenching effect (CQE) of the dye-dopant was slightly bigger in the former than in the latter, while the degrees of CQE for three dopants are in the order of DMQA > DCJTB > Rubrene suggested by the difference in EL spectra and performances of devices. In addition, EL process of device with an ultra-thin layer of dopant is dominated by direct carrier trapping (DCT) process due to almost no holes recombine with electrons in Alq{sub 3}-host layer.

An extended five-stream model for diffusion of ion-implanted dopants in monocrystalline silicon

International Nuclear Information System (INIS)

Khina, B.B.

2007-01-01

Low-energy high-dose ion implantation of different dopants (P, Sb, As, B and others) into monocrystalline silicon with subsequent thermal annealing is used for the formation of ultra-shallow p-n junctions in modern VLSI circuit technology. During annealing, dopant activation and diffusion in silicon takes place. The experimentally observed phenomenon of transient enhanced diffusion (TED), which is typically ascribed to the interaction of diffusing species with non-equilibrium point defects accumulated in silicon due to ion damage, and formation of small clusters and extended defects, hinders further down scaling of p-n junctions in VLSI circuits. TED is currently a subject of extensive experimental and theoretical investigation in many binary and multicomponent systems. However, the state-of-the-art mathematical models of dopant diffusion, which are based on the so-called 'five-stream' approach, and modern TCAD software packages such as SUPREM-4 (by Silvaco Data Systems, Ltd.) that implement these models encounter severe difficulties in describing TED. Solving the intricate problem of TED suppression and development of novel regimes of ion implantation and rapid thermal annealing is impossible without elaboration of new mathematical models and computer simulation of this complex phenomenon. In this work, an extended five-stream model for diffusion in silicon is developed which takes into account all possible charge states of point defects (vacancies and silicon self-interstitials) and diffusing pairs 'dopant atom-vacancy' and 'dopant atom-silicon self-interstitial'. The model includes the drift terms for differently charged point defects and pairs in the internal electric field and the kinetics of interaction between unlike 'species' (generation and annihilation of pairs and annihilation of point defects). Expressions for diffusion coefficients and numerous sink/source terms that appear in the non-linear, non-steady-state reaction-diffusion equations are derived

Anomalous radial and angular strain relaxation around dilute p-, isoelectronic-, and n-type dopants in Si crystal

Energy Technology Data Exchange (ETDEWEB)

Zhao, Mingshu [School of Physical Sciences, University of Science and Technology of China, Hefei, Anhui Province 230026 (China); Dong, Juncai, E-mail: dongjc@ihep.ac.cn [Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049 (China); Chen, Dongliang [Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049 (China)

2017-02-01

Doping is widely applied in yielding desirable properties and functions in silicon technology; thus, fully understanding the relaxation mechanism for lattice-mismatch strain is of fundamental importance. Here we systematically study the local lattice distortion near dilute IIIA-, IVA-, and VA-group substitutional dopants in Si crystal using density functional theory, and anomalous radial and angular strain relaxation modes are first revealed. Both the nearest-neighbor (NN) bond-distances and the tetrahedral bond-angles are found to exhibit completely opposite dependence on the electronic configurations for the low Z (Z<26) and high Z (Z>26) dopants. More surprisingly, negative and positive angular shifts for the second NN twelve Si2 atoms are unveiled surrounding the p- and n-type dopants, respectively. While electron localization function shows that the doped hole and electron are highly localized near the dopants, hence being responsible for the abnormal angular shifts, a universal radial strain relaxation mechanism dominated by a competition of the Coulomb interactions among the ion-core, bond-charge, and the localized hole or electron is also proposed. These findings may prove to be instrumental in precise design of silicon-based solotronics.

High hole mobility p-type GaN with low residual hydrogen concentration prepared by pulsed sputtering

Science.gov (United States)

Arakawa, Yasuaki; Ueno, Kohei; Kobayashi, Atsushi; Ohta, Jitsuo; Fujioka, Hiroshi

2016-08-01

We have grown Mg-doped GaN films with low residual hydrogen concentration using a low-temperature pulsed sputtering deposition (PSD) process. The growth system is inherently hydrogen-free, allowing us to obtain high-purity Mg-doped GaN films with residual hydrogen concentrations below 5 × 1016 cm-3, which is the detection limit of secondary ion mass spectroscopy. In the Mg profile, no memory effect or serious dopant diffusion was detected. The as-deposited Mg-doped GaN films showed clear p-type conductivity at room temperature (RT) without thermal activation. The GaN film doped with a low concentration of Mg (7.9 × 1017 cm-3) deposited by PSD showed hole mobilities of 34 and 62 cm2 V-1 s-1 at RT and 175 K, respectively, which are as high as those of films grown by a state-of-the-art metal-organic chemical vapor deposition apparatus. These results indicate that PSD is a powerful tool for the fabrication of GaN-based vertical power devices.

Effect of different carbon fillers and dopant acids on electrical ...

Indian Academy of Sciences (India)

The nature of both the carbon filler and the dopant acid can significantly influence the conductivity of these nanocomposites. This paper describes the effects of carbon fillers like carbon black (CB), graphite (GR) and muti-walled carbon nanotubes (MWCNT) and of dopant acids like methane sulfonic acid (MSA), camphor ...

Dynamics of δ-dopant redistribution during heterostructure growth

Science.gov (United States)

Pankratov, E. L.

2007-06-01

It has recently been shown that growth of a multilayer structure with one or more delta-layers at high temperature leads to spreading and asymmetrization of the dopant distribution [see, for example, E.F.J. Schubert, Vac. Sci. Technol. A. 8, 2980 (1990), A.M. Nazmul, S. Sugahara, M. Tanaka, J. Crystal Growth 251, 303 (2003); R.C. Newman, M.J. Ashwin, M.R. Fahy, L. Hart, S.N. Holmes, C. Roberts, X. Zhang, Phys. Rev. B 54, 8769 (1996); E.F. Schubert, J.M. Kuo, R.F. Kopf, H.S. Luftman, L.C. Hopkins, N.J. Sauer, J. Appl. Phys. 67, 1969 (1990); P.M. Zagwijn, J.F. van der Veen, E. Vlieg, A.H. Reader, D.J. Gravesteijn, J. Appl. Phys. 78, 4933 (1995); W.S. Hobson, S.J. Pearton, E.F. Schubert, G. Cabaniss, Appl. Phys. Lett. 55, 1546 (1989); Delta Doping of Semiconductors, edited by E.F. Schubert (Cambridge University Press, Cambridge, 1996); Yu.N. Drozdov, N.B. Baidus', B.N. Zvonkov, M.N. Drozdov, O.I. Khrykin, V.I. Shashkin, Semiconductors 37, 194 (2003); E. Skuras, A.R. Long, B. Vogele, M.C. Holland, C.R. Stanley, E.A. Johnson, M. van der Burgt, H. Yaguchi, J. Singleton, Phys. Rev. B 59, 10712 (1999); G. Li, C. Jagadish, Solid-State Electronics 41, 1207 (1997)]. In this work analytical and numerical analysis of dopant dynamics in a delta-doped area of a multilayer structure has been accomplished using Fick's second law. Some reasons for asymmetrization of a delta-dopant distribution are illustrated. The spreading of a delta-layer has been estimated using example materials of a multilayer structure, a delta-layer and an overlayer.

Valence and atomic size dependent exchange barriers in vacancy-mediated dopant diffusion

International Nuclear Information System (INIS)

Nelson, J.S.; Schultz, P.A.; Wright, A.F.

1998-01-01

First-principles pseudopotential calculations of dopant-vacancy exchange barriers indicate a strong dependency on dopant valence and atomic size, in contrast to current models of vacancy-mediated dopant diffusion. First-row elements (B, C, N) are found to have exchange barriers which are an order of magnitude larger than the assumed value of 0.3 eV (the Si vacancy migration energy). copyright 1998 American Institute of Physics

Coupling of erbium dopants to yttrium orthosilicate photonic crystal cavities for on-chip optical quantum memories

Energy Technology Data Exchange (ETDEWEB)

Miyazono, Evan; Zhong, Tian; Craiciu, Ioana; Kindem, Jonathan M.; Faraon, Andrei, E-mail: faraon@caltech.edu [T. J. Watson Laboratory of Applied Physics, California Institute of Technology, 1200 E California Blvd, Pasadena, California 91125 (United States)

2016-01-04

Erbium dopants in crystals exhibit highly coherent optical transitions well suited for solid-state optical quantum memories operating in the telecom band. Here, we demonstrate coupling of erbium dopant ions in yttrium orthosilicate to a photonic crystal cavity fabricated directly in the host crystal using focused ion beam milling. The coupling leads to reduction of the photoluminescence lifetime and enhancement of the optical depth in microns-long devices, which will enable on-chip quantum memories.

Color optimization of single emissive white OLEDs via energy transfer between RGB fluorescent dopants

Energy Technology Data Exchange (ETDEWEB)

Kim, Nam Ho; Kim, You-Hyun; Yoon, Ju-An; Lee, Sang Youn [Department of Green Energy and Semiconductor Engineering, Hoseo University, Asan (Korea, Republic of); Ryu, Dae Hyun [Department of Information Technology, Hansei University, Gunpo (Korea, Republic of); Wood, Richard [Department of Engineering Physics, McMaster University, Hamilton, Ontario, Canada L8S 4L7 (Canada); Moon, C.-B. [Department of Green Energy and Semiconductor Engineering, Hoseo University, Asan (Korea, Republic of); Kim, Woo Young, E-mail: wykim@hoseo.edu [Department of Green Energy and Semiconductor Engineering, Hoseo University, Asan (Korea, Republic of); Department of Engineering Physics, McMaster University, Hamilton, Ontario, Canada L8S 4L7 (Canada)

2013-11-15

The electroluminescent characteristics of white organic light-emitting diodes (WOLEDs) were investigated including single emitting layer (SEL) with an ADN host and dopants; BCzVBi, C545T, and DCJTB for blue, green and red emission, respectively. The structure of the high efficiency WOLED device was; ITO/NPB(700 Å)/ADN: BCzVBi-7%:C545T-0.05%:DCJTB-0.1%(300 Å)/Bphen(300 Å)/Liq(20 Å)/Al(1200 Å) for mixing three primary colors. Luminous efficiency was 9.08 cd/A at 3.5 V and Commission Intenationale de L’eclairage (CIE{sub x,y}) coordinates of white emission was measured as (0.320, 0.338) at 8 V while simulated CIE{sub x,y} coordinates were (0.336, 0.324) via estimation from each dopant's PL spectrum. -- Highlights: • This paper observes single-emissive-layered white OLED using fluorescent dopants. • Electrical and optical properties are analyzed. • Color stability of white OLED is confirmed for new planar light source.

Color optimization of single emissive white OLEDs via energy transfer between RGB fluorescent dopants

International Nuclear Information System (INIS)

Kim, Nam Ho; Kim, You-Hyun; Yoon, Ju-An; Lee, Sang Youn; Ryu, Dae Hyun; Wood, Richard; Moon, C.-B.; Kim, Woo Young

2013-01-01

The electroluminescent characteristics of white organic light-emitting diodes (WOLEDs) were investigated including single emitting layer (SEL) with an ADN host and dopants; BCzVBi, C545T, and DCJTB for blue, green and red emission, respectively. The structure of the high efficiency WOLED device was; ITO/NPB(700 Å)/ADN: BCzVBi-7%:C545T-0.05%:DCJTB-0.1%(300 Å)/Bphen(300 Å)/Liq(20 Å)/Al(1200 Å) for mixing three primary colors. Luminous efficiency was 9.08 cd/A at 3.5 V and Commission Intenationale de L’eclairage (CIE x,y ) coordinates of white emission was measured as (0.320, 0.338) at 8 V while simulated CIE x,y coordinates were (0.336, 0.324) via estimation from each dopant's PL spectrum. -- Highlights: • This paper observes single-emissive-layered white OLED using fluorescent dopants. • Electrical and optical properties are analyzed. • Color stability of white OLED is confirmed for new planar light source

Local structure investigation of Ga and Yb dopants in Co4Sb12 skutterudites

Science.gov (United States)

Hu, Yanyun; Chen, Ning; Clancy, J. P.; Salvador, James R.; Kim, Chang-Yong; Shi, Xiaoya; Li, Qiang; Kim, Young-June

2017-12-01

We report comprehensive x-ray absorption spectroscopy studies at both the Ga K edge and Yb L2 edge to elucidate the local structure of Ga and Yb dopants in YbxGayCo4Sb12 . Our extended x-ray absorption fine structure (EXAFS) data confirm that Ga atoms occupy two crystallographic sites: one is the 24 g site replacing Sb, and the other is the 2 a site in the off-center void position. We find that the occupancy ratio of these two sites varies significantly as a function of the filling fraction of additional Yb, which exclusively occupies the 2 a on-center site. At low concentrations of Yb, Ga24 g and Ga2 a dopants coexist and they form a charge-compensated compound defect proposed by Qiu et al. [Adv. Funct. Mater. 23, 3194 (2013), 10.1002/adfm.201202571]. The Ga24 g occupancy increases gradually with increasing Yb concentration, and almost all Ga occupies the 24 g site for the highest Yb concentration studied (x =0.4 ). In addition to the local structural evidence provided by our EXAFS data, we also present x-ray absorption near-edge structure (XANES) spectra, which show a small Ga K -edge energy shift as a function of Yb concentration consistent with the change from predominantly Ga2 a to Ga24 g states. Our result suggests that the increased solubility of Yb in Yb-Ga co-doped Co4Sb12 skutterudites is due to the increased Ga24 g electron acceptor, and thus provides an important strategy to optimize the carrier concentration in partially filled skutterudites.

Germania and Alumina Dopant Diffusion and Viscous Flow Effects at Preparation of Doped Optical Fibers

Directory of Open Access Journals (Sweden)

Jens Kobelke

2017-01-01

Full Text Available We report on germania and alumina dopant profile shift effects at preparation of compact optical fibers using packaging methods (Stack-and-Draw method, Rod-in-Tube (RiT technique. The sintering of package hollow volume by viscous flow results in a shift of the core-pitch ratio in all-solid microstructured fibers. The ratio is increased by about 5% in the case of a hexagonal package. The shift by diffusion effects of both dopants is simulated for typical slow speed drawing parameters. Thermodynamic approximations of surface dissociation of germania doped silica suggest the need of an adequate undoped silica barrier layer to prevent an undesired bubble formation at fiber drawing. In contrast, alumina doping does not estimate critical dissociation effects with vaporous aluminium oxide components. We report guide values of diffusion length of germania and alumina for the drawing process by kinetic approximation. The germania diffusion involves a small core enlargement, typically in the sub-micrometer scale. Though, the alumina diffusion enlarges it by a few micrometers. A drawn pure alumina preform core rod transforms to an amorphous aluminosilicate core with a molar alumina concentration of only about 50% and a non-gaussian concentration profile.

Atom-probe for FinFET dopant characterization

Energy Technology Data Exchange (ETDEWEB)

Kambham, A.K., E-mail: kambham@imec.be [K.U.Leuven, Instituut voor Kern-en Stralings fysika, Celestijnenlaan 200D, B-3001, Leuven (Belgium); IMEC, Kapeldreef 75, B-3001 Leuven (Belgium); Mody, J.; Gilbert, M.; Koelling, S.; Vandervorst, W. [K.U.Leuven, Instituut voor Kern-en Stralings fysika, Celestijnenlaan 200D, B-3001, Leuven (Belgium); IMEC, Kapeldreef 75, B-3001 Leuven (Belgium)

2011-05-15

With the continuous shrinking of transistors and advent of new transistor architectures to keep in pace with Moore's law and ITRS goals, there is a rising interest in multigate 3D-devices like FinFETs where the channel is surrounded by gates on multiple surfaces. The performance of these devices depends on the dimensions and the spatial distribution of dopants in source/drain regions of the device. As a result there is a need for new metrology approach/technique to characterize quantitatively the dopant distribution in these devices with nanometer precision in 3D. In recent years, atom probe tomography (APT) has shown its ability to analyze semiconductor and thin insulator materials effectively with sub-nm resolution in 3D. In this paper we will discuss the methodology used to study FinFET-based structures using APT. Whereas challenges and solutions for sample preparation linked to the limited fin dimensions already have been reported before, we report here an approach to prepare fin structures for APT, which based on their processing history (trenches filled with Si) are in principle invisible in FIB and SEM. Hence alternative solutions in locating and positioning them on the APT-tip are presented. We also report on the use of the atom probe results on FinFETs to understand the role of different dopant implantation angles (10{sup o} and 45{sup o}) when attempting conformal doping of FinFETs and provide a quantitative comparison with alternative approaches such as 1D secondary ion mass spectrometry (SIMS) and theoretical model values. -- Research highlights: {yields} This paper provides the information on how to characterize the FinFET devices using atom probe tomography (APT). {yields} Importance of this work is to assess the performance of these devices at different processing conditions by extracting the compositional profiles. {yields} The performance of these devices depends on the dimensions and the spatial distribution of dopants in source/drain regions

Atom-probe for FinFET dopant characterization

International Nuclear Information System (INIS)

Kambham, A.K.; Mody, J.; Gilbert, M.; Koelling, S.; Vandervorst, W.

2011-01-01

With the continuous shrinking of transistors and advent of new transistor architectures to keep in pace with Moore's law and ITRS goals, there is a rising interest in multigate 3D-devices like FinFETs where the channel is surrounded by gates on multiple surfaces. The performance of these devices depends on the dimensions and the spatial distribution of dopants in source/drain regions of the device. As a result there is a need for new metrology approach/technique to characterize quantitatively the dopant distribution in these devices with nanometer precision in 3D. In recent years, atom probe tomography (APT) has shown its ability to analyze semiconductor and thin insulator materials effectively with sub-nm resolution in 3D. In this paper we will discuss the methodology used to study FinFET-based structures using APT. Whereas challenges and solutions for sample preparation linked to the limited fin dimensions already have been reported before, we report here an approach to prepare fin structures for APT, which based on their processing history (trenches filled with Si) are in principle invisible in FIB and SEM. Hence alternative solutions in locating and positioning them on the APT-tip are presented. We also report on the use of the atom probe results on FinFETs to understand the role of different dopant implantation angles (10 o and 45 o ) when attempting conformal doping of FinFETs and provide a quantitative comparison with alternative approaches such as 1D secondary ion mass spectrometry (SIMS) and theoretical model values. -- Research highlights: → This paper provides the information on how to characterize the FinFET devices using atom probe tomography (APT). → Importance of this work is to assess the performance of these devices at different processing conditions by extracting the compositional profiles. → The performance of these devices depends on the dimensions and the spatial distribution of dopants in source/drain regions. → In this publication we

Origin of electrolyte-dopant dependent sulfur poisoning of SOFC anodes.

Science.gov (United States)

Zeng, ZhenHua; Björketun, Mårten E; Ebbesen, Sune; Mogensen, Mogens B; Rossmeisl, Jan

2013-05-14

The mechanisms governing the sulfur poisoning of the triple phase boundary (TPB) of Ni-XSZ (X2O3 stabilized zirconia) anodes have been investigated using density functional theory. The calculated sulfur adsorption energies reveal a clear correlation between the size of the cation dopant X(3+) and the sulfur tolerance of the Ni-XSZ anode; the smaller the ionic radius, the higher the sulfur tolerance. The mechanistic study shows that the size of X(3+) strongly influences XSZ's surface energy, which in turn determines the adhesion of Ni to XSZ. The Ni-XSZ interaction has a direct impact on the Ni-S interaction and on the relative stability of reconstructed and pristine Ni(100) facets at the TPB. Together, these two effects control the sulfur adsorption on the Ni atoms at the TPB. The established relationships explain experimentally observed dopant-dependent anode performances and provide a blueprint for the future search for and preparation of highly sulfur tolerant anodes.

Finite element simulations of electrostatic dopant potentials in thin semiconductor specimens for electron holography.

Science.gov (United States)

Somodi, P K; Twitchett-Harrison, A C; Midgley, P A; Kardynał, B E; Barnes, C H W; Dunin-Borkowski, R E

2013-11-01

Two-dimensional finite element simulations of electrostatic dopant potentials in parallel-sided semiconductor specimens that contain p-n junctions are used to assess the effect of the electrical state of the surface of a thin specimen on projected potentials measured using off-axis electron holography in the transmission electron microscope. For a specimen that is constrained to have an equipotential surface, the simulations show that the step in the projected potential across a p-n junction is always lower than would be predicted from the properties of the bulk device, but is relatively insensitive to the value of the surface state energy, especially for thicker specimens and higher dopant concentrations. The depletion width measured from the projected potential, however, has a complicated dependence on specimen thickness. The results of the simulations are of broader interest for understanding the influence of surfaces and interfaces on electrostatic potentials in nanoscale semiconductor devices. © 2013 Elsevier B.V. All rights reserved.

Metal modulation epitaxy growth for extremely high hole concentrations above 1019 cm-3 in GaN

Science.gov (United States)

Namkoong, Gon; Trybus, Elaissa; Lee, Kyung Keun; Moseley, Michael; Doolittle, W. Alan; Look, David C.

2008-10-01

The free hole carriers in GaN have been limited to concentrations in the low 1018cm-3 range due to the deep activation energy, lower solubility, and compensation from defects, therefore, limiting doping efficiency to about 1%. Herein, we report an enhanced doping efficiency up to ˜10% in GaN by a periodic doping, metal modulation epitaxy growth technique. The hole concentrations grown by periodically modulating Ga atoms and Mg dopants were over ˜1.5×1019cm-3.

Manipulation and analysis of a single dopant atom in GaAs

NARCIS (Netherlands)

Wijnheijmer, A.P.

2011-01-01

This thesis focuses on the manipulation and analysis of single dopant atoms in GaAs by scanning tunneling microscopy (STM) and spectroscopy (STS) at low temperatures. The observation of ionization rings is one of the key results, showing that we can control the charge state of a single dopant atom

Magnetic properties of ZnO nanowires with Li dopants and Zn vacancies

Energy Technology Data Exchange (ETDEWEB)

Guan, Xinhong; Cai, Ningning [Key Laboratory of Information Photonics and Optical Communications (Beijing University of Posts and Telecommunications), Ministry of Education, P.O. Box 72, Beijing 100876 (China); Yang, Chuanghua [School of Physics and Telecommunication Engineering, Shanxi University of Technology (SNUT), Hanzhong 723001, Shanxi (China); Chen, Jun [Beijing Applied Physics and Computational Mathematics, Beijing 100088 (China); Lu, Pengfei, E-mail: photon.bupt@gmail.com [Key Laboratory of Information Photonics and Optical Communications (Beijing University of Posts and Telecommunications), Ministry of Education, P.O. Box 72, Beijing 100876 (China)

2016-04-30

The electronic and magnetic properties of ZnO nanowire with Li dopants and vacancies have been investigated using first-principles density functional theory. It is found that the Zn vacancy can induce magnetism while increasing the formation energy of the system. However, the calculated results indicate that the introduction of Li-dopants will reduce the formation energy of system. We also have studied the magnetic couplings with vacancies as well as their corresponding configurations with Li-dopants for four configurations of ZnO nanowires. The results show that ferromagnetic properties can be improved/reversed after the introduction of Li-dopants. Ferromagnetic mechanism is originated from the fierce p–p hybridization of O near the Fermi level. We find that ferromagnetism of Li-doped ZnO nanowires with Zn vacancies can be realized at room temperature and they are promising spintronic materials. - Highlights: • Li-dopants will reduce the formation energy of ZnO nanowires with Zn vacancy. • The fierce p–p hybridization of O near Fermi level is responsible for FM properties. • Li-doped ZnO–V{sub Zn} nanowire is a promising FM semiconductor material.

Carrier illumination measurement of dopant lateral diffusion

International Nuclear Information System (INIS)

Budiarto, E.; Segovia, M.; Borden, P.; Felch, S.

2005-01-01

This paper describes the application of the carrier illumination technique to non-destructively measure the lateral diffusion of implanted dopants after annealing. Experiments to validate the feasibility of this method employed test structures with a constant line width of 300 nm and varying undoped spaces of 100-5000 nm. The test patterns were implanted with a p-type dopant and annealed in a 3 x 3 matrix. For each implant condition, the measured lateral diffusion was found to increase with annealing temperature, as expected. More interestingly, the lateral diffusion was not observed to relate to the vertical diffusion by a fixed proportionality factor, as is usually assumed. The ratio of lateral to vertical diffusion varies with annealing temperature, with a trend that depends on the implant condition

Tuning Cu dopant of Zn 0.5 Cd 0.5 S nanocrystals enables high-performance photocatalytic H 2 evolution from water splitting under visible-light irradiation

Energy Technology Data Exchange (ETDEWEB)

Mei, Zongwei; Zhang, Bingkai; Zheng, Jiaxin; Yuan, Sheng; Zhuo, Zengqing; Meng, Xianguang; Chen, Zonghai; Amine, Khalil; Yang, Wanli; Wang, Lin. -Wang; Wang, Wei; Wang, Shufeng; Gong, Qihuang; Li, Jun; Liu, Fu. -Sheng; Pan, Feng

2016-08-01

Cu-doping into Zn1-xCdxS can greatly enhance the photocatalytic H2 evolution from water splitting under visible-light irradiation. However, it is still controversial for how the Cu-dopant improves this performance. Here, we report that appropriate Cu-doped Zn0.5Cd0.5S nanocrystals reach 21.4 mmol/h/g of H2 evolution rate without cocatalyst in the visible-light region, which is also 2.8 times as high as that of the undoped counterpart, and the corresponding apparent quantum efficiency is 18.8% at 428 nm. It is firstly confirmed that the Cu2+ changes into Cu+ after being doped by soft X-ray absorption spectroscopy (sXAS). We theoretically propose that the transformation of 2Cu2+ to 2Cu+ results in one adjacent S2- vacancy (VS) in host during the doping process, while the Cu+-dopant and VS attract the photoexcited holes and electrons, respectively. Accordingly, the photocatalytic activity is improved due to the enhanced separation of photoexcited carriers accompanied with the enhanced light absorption resulting from the Cu+-dopant and 2Cu+/VS complex as possible active site for photocatalytic H2 evolution.

High mobility and high concentration Type-III heterojunction FET

Science.gov (United States)

Tsu, R.; Fiddy, M. A.; Her, T.

2018-02-01

The PN junction was introduced in transistors by doping, resulting in high losses due to Coulomb scattering from the dopants. The MOSFET introduced carriers in the form of electrons and holes with an applied bias to the oxide barrier, resulting in carrier transfer without doping. This avoids high scattering losses and dominates the IC industries. With heterojunctions having valence-band maxima near and even above the conduction-band minimum in the formation of Type-III superlattices, very useful devices, introduced by Tsu, Sai-Halacz, and Esaki, soon followed. If the layer thicknesses are more than the carrier mean-free-path, incoherent scattering results in the formation of carrier transfer via diffusion instead of opening up new energy gaps. The exploitation of carriers without scattering represents a new and significant opportunity in what we call a Broken Gap Heterojunction FET.

Site-selective dopant profiling of p-n junction specimens in the dual-beam FIB/SEM system

International Nuclear Information System (INIS)

Chee, K W A; Beanland, R; Midgley, P A; Humphreys, C J

2010-01-01

Results from site-specific dopant profiling in a dual-beam FIB/SEM system are reported. Si specimens containing p-n junctions were milled using Ga + ion beam energies ranging from 30 keV to 2 keV, and analysed in situin the vacuum chamber. We compare the dopant contrast observed when milling a cleaved surface to that obtained from a side-wall of a trench cut using 30 kV Ga + ions, and using successively lower ion beam energies. The latter technique is suitable for site-specific dopant profiling. We find that lower energy ion beam milling significantly improves contrast, but only achieves 50 % of that observed on a freshly-cleaved surface. Furthermore, the contrast on a side-wall previously milled using high energy Ga + ions is less than that of a cleaved surface subjected to the same ion beam energy.

Photoreflection investigations of the dopant activation in InP doped with beryllium ions

International Nuclear Information System (INIS)

Avakyants, L.P.; Bokov, P.Yu.; Chervyakov, A.V.

2005-01-01

The processes of the dopant activation in the InP crystals implanted with Be + ions (energy 100 keV, dose 10 13 cm -2 and subsequent thermal annealing during 10 s) have been studied by means of photoreflection spectroscopy. Spectral lines of the crystal InP were absent in the photoreflection spectra of the samples annealed at temperatures less then 400 Deg C. This fact is connected with the disordering of the crystal structure due to the ion implantation. In the temperature range 400-700 Deg C the lines from InP band gap (1.34 eV) and conductance band-spin-orbit splitting valence subband (1.44 eV) have been observed due to the recovery of the crystal structure. In the photoreflectance spectra of a 800 Deg C annealed sample the Franz-Keldysh oscillations have been observed, which can be an evidence in favour of the dopant activation. Carrier concentration calculated from the period of Franz-Keldysh oscillations was equal to 2.2 x 10 16 cm -3 [ru

A phononic crystal strip based on silicon for support tether applications in silicon-based MEMS resonators and effects of temperature and dopant on its band gap characteristics

Directory of Open Access Journals (Sweden)

Thi Dep Ha

2016-04-01

Full Text Available Phononic crystals (PnCs and n-type doped silicon technique have been widely employed in silicon-based MEMS resonators to obtain high quality factor (Q as well as temperature-induced frequency stability. For the PnCs, their band gaps play an important role in the acoustic wave propagation. Also, the temperature and dopant doped into silicon can cause the change in its material properties such as elastic constants, Young’s modulus. Therefore, in order to design the simultaneous high Q and frequency stability silicon-based MEMS resonators by two these techniques, a careful design should study effects of temperature and dopant on the band gap characteristics to examine the acoustic wave propagation in the PnC. Based on these, this paper presents (1 a proposed silicon-based PnC strip structure for support tether applications in low frequency silicon-based MEMS resonators, (2 influences of temperature and dopant on band gap characteristics of the PnC strips. The simulation results show that the largest band gap can achieve up to 33.56 at 57.59 MHz and increase 1280.13 % (also increase 131.89 % for ratio of the widest gaps compared with the counterpart without hole. The band gap properties of the PnC strips is insignificantly effected by temperature and electron doping concentration. Also, the quality factor of two designed length extensional mode MEMS resonators with proposed PnC strip based support tethers is up to 1084.59% and 43846.36% over the same resonators with PnC strip without hole and circled corners, respectively. This theoretical study uses the finite element analysis in COMSOL Multiphysics and MATLAB softwares as simulation tools. This findings provides a background in combination of PnC and dopant techniques for high performance silicon-based MEMS resonators as well as PnC-based MEMS devices.

A phononic crystal strip based on silicon for support tether applications in silicon-based MEMS resonators and effects of temperature and dopant on its band gap characteristics

Energy Technology Data Exchange (ETDEWEB)

Ha, Thi Dep, E-mail: hathidep@yahoo.com [School of Electronic Engineering, University of Electronic Science and Technology of China, Chengdu 611731 (China); Faculty of Electronic Technology, Industrial University of Ho Chi Minh City, Hochiminh City (Viet Nam); Bao, JingFu, E-mail: baojingfu@uestc.edu.cn [School of Electronic Engineering, University of Electronic Science and Technology of China, Chengdu 611731 (China)

2016-04-15

Phononic crystals (PnCs) and n-type doped silicon technique have been widely employed in silicon-based MEMS resonators to obtain high quality factor (Q) as well as temperature-induced frequency stability. For the PnCs, their band gaps play an important role in the acoustic wave propagation. Also, the temperature and dopant doped into silicon can cause the change in its material properties such as elastic constants, Young’s modulus. Therefore, in order to design the simultaneous high Q and frequency stability silicon-based MEMS resonators by two these techniques, a careful design should study effects of temperature and dopant on the band gap characteristics to examine the acoustic wave propagation in the PnC. Based on these, this paper presents (1) a proposed silicon-based PnC strip structure for support tether applications in low frequency silicon-based MEMS resonators, (2) influences of temperature and dopant on band gap characteristics of the PnC strips. The simulation results show that the largest band gap can achieve up to 33.56 at 57.59 MHz and increase 1280.13 % (also increase 131.89 % for ratio of the widest gaps) compared with the counterpart without hole. The band gap properties of the PnC strips is insignificantly effected by temperature and electron doping concentration. Also, the quality factor of two designed length extensional mode MEMS resonators with proposed PnC strip based support tethers is up to 1084.59% and 43846.36% over the same resonators with PnC strip without hole and circled corners, respectively. This theoretical study uses the finite element analysis in COMSOL Multiphysics and MATLAB softwares as simulation tools. This findings provides a background in combination of PnC and dopant techniques for high performance silicon-based MEMS resonators as well as PnC-based MEMS devices.

Metal modulation epitaxy growth for extremely high hole concentrations above 1019 cm-3 in GaN

International Nuclear Information System (INIS)

Namkoong, Gon; Trybus, Elaissa; Lee, Kyung Keun; Moseley, Michael; Doolittle, W. Alan; Look, David C.

2008-01-01

The free hole carriers in GaN have been limited to concentrations in the low 10 18 cm -3 range due to the deep activation energy, lower solubility, and compensation from defects, therefore, limiting doping efficiency to about 1%. Herein, we report an enhanced doping efficiency up to ∼10% in GaN by a periodic doping, metal modulation epitaxy growth technique. The hole concentrations grown by periodically modulating Ga atoms and Mg dopants were over ∼1.5x10 19 cm -3

The Origin of Improved Electrical Double-Layer Capacitance by Inclusion of Topological Defects and Dopants in Graphene for Supercapacitors.

Science.gov (United States)

Chen, Jiafeng; Han, Yulei; Kong, Xianghua; Deng, Xinzhou; Park, Hyo Ju; Guo, Yali; Jin, Song; Qi, Zhikai; Lee, Zonghoon; Qiao, Zhenhua; Ruoff, Rodney S; Ji, Hengxing

2016-10-24

Low-energy density has long been the major limitation to the application of supercapacitors. Introducing topological defects and dopants in carbon-based electrodes in a supercapacitor improves the performance by maximizing the gravimetric capacitance per mass of the electrode. However, the main mechanisms governing this capacitance improvement are still unclear. We fabricated planar electrodes from CVD-derived single-layer graphene with deliberately introduced topological defects and nitrogen dopants in controlled concentrations and of known configurations, to estimate the influence of these defects on the electrical double-layer (EDL) capacitance. Our experimental study and theoretical calculations show that the increase in EDL capacitance due to either the topological defects or the nitrogen dopants has the same origin, yet these two factors improve the EDL capacitance in different ways. Our work provides a better understanding of the correlation between the atomic-scale structure and the EDL capacitance and presents a new strategy for the development of experimental and theoretical models for understanding the EDL capacitance of carbon electrodes. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Photo-dissociation of hydrogen passivated dopants in gallium arsenide

International Nuclear Information System (INIS)

Tong, L.; Larsson, J.A.; Nolan, M.; Murtagh, M.; Greer, J.C.; Barbe, M.; Bailly, F.; Chevallier, J.; Silvestre, F.S.; Loridant-Bernard, D.; Constant, E.; Constant, F.M.

2002-01-01

A theoretical and experimental study of the photo-dissociation mechanisms of hydrogen passivated n- and p-type dopants in gallium arsenide is presented. The photo-induced dissociation of the Si Ga -H complex has been observed for relatively low photon energies (3.48 eV), whereas the photo-dissociation of C As -H is not observed for photon energies up to 5.58 eV. This fundamental difference in the photo-dissociation behavior between the two dopants is explained in terms of the localized excitation energies about the Si-H and C-H bonds

Dynamics of Defects and Dopants in Complex Systems: Si and Oxide Surfaces and Interfaces

Science.gov (United States)

Kirichenko, Taras; Yu, Decai; Banarjee, Sanjay; Hwang, Gyeong

2004-10-01

Fabrication of forthcoming nanometer scale electronic devices faces many difficulties including formation of extremely shallow and highly doped junctions. At present, ultra-low-energy ion implantation followed by high-temperature thermal annealing is most widely used to fabricate such ultra-shallow junctions. In the process, a great challenge lies in achieving precise control of redistribution and electrical activation of dopant impurities. Native defects (such as vacancies and interstitials) generated during implantation are known to be mainly responsible for the TED and also influence significantly the electrical activation/deactivation. Defect-dopant dynamics is rather well understood in crystalline Si and SiO2. However, little is known about their diffusion and annihilation (or precipitation) at the surfaces and interfaces, despite its growing importance in determining junction profiles as device dimensions get smaller. In this talk, we will present our density functional theory calculation results on the atomic and electronic structure and dynamical behavior of native defects and dopant-defect complexes in disordered/strained Si and oxide systems, such as i) clean and absorbent-modified Si(100) surface and subsurface layers, ii) amorphous-crystalline Si interfaces and iii) amorphous SiO2/Si interfaces. The fundamental understanding and data is essential in developing a comprehensive kinetic model for junction formation, which would contribute greatly in improving current process technologies.

The influence of a Cr-dopant on the properties of α-FeOOH particles precipitated in highly alkaline media

International Nuclear Information System (INIS)

Krehula, Stjepko; Music, Svetozar

2009-01-01

The effects of a Cr-dopant on the precipitation of acicular α-FeOOH particles, the formation of solid solutions, particle size and shape were investigated using X-ray powder diffraction (XRD), Moessbauer and Fourier transform infrared (FT-IR) spectroscopies and field emission scanning electron microscopy (FE-SEM). Acicular and monodisperse α-FeOOH particles were precipitated at a very high pH by heating the suspension obtained by adding a tetramethylammonium hydroxide solution to an aqueous solution of FeCl 3 . The influence of the Cr-dopant was investigated by addition of various amounts of Cr 3+ ions to the initial FeCl 3 solution, where r = 100[Cr]/([Cr] + [Fe]) stands for the added amount of Cr. XRD analysis of the obtained powders (with r values from 0 to 23.08) showed only the presence of the diffraction lines characteristic for α-FeOOH. Moessbauer spectroscopy showed a decrease in hyperfine magnetic field of α-FeOOH with an increase in Cr addition which indicates Cr incorporation into the α-FeOOH structure. The OH bending bands in the FT-IR spectra showed only a slight change in position with an increase in r, but the considerable increase in the lattice band wave number indicated a decrease in thickness of the lath-like α-FeOOH particles. This conclusion was confirmed by FE-SEM observations

One- and two-dimensional dopant/carrier profiling for ULSI

Science.gov (United States)

Vandervorst, W.; Clarysse, T.; De Wolf, P.; Trenkler, T.; Hantschel, T.; Stephenson, R.; Janssens, T.

1998-11-01

Dopant/carrier profiles constitute the basis of the operation of a semiconductor device and thus play a decisive role in the performance of a transistor and are subjected to the same scaling laws as the other constituents of a modern semiconductor device and continuously evolve towards shallower and more complex configurations. This evolution has increased the demands on the profiling techniques in particular in terms of resolution and quantification such that a constant reevaluation and improvement of the tools is required. As no single technique provides all the necessary information (dopant distribution, electrical activation,..) with the requested spatial and depth resolution, the present paper attempts to provide an assessment of those tools which can be considered as the main metrology technologies for ULSI-applications. For 1D-dopant profiling secondary ion mass spectrometry (SIMS) has progressed towards a generally accepted tool meeting the requirements. For 1D-carrier profiling spreading resistance profiling and microwave surface impedance profiling are envisaged as the best choices but extra developments are required to promote them to routinely applicable methods. As no main metrology tool exist for 2D-dopant profiling, main emphasis is on 2D-carrier profiling tools based on scanning probe microscopy. Scanning spreading resistance (SSRM) and scanning capacitance microscopy (SCM) are the preferred methods although neither of them already meets all the requirements. Complementary information can be extracted from Nanopotentiometry which samples the device operation in more detail. Concurrent use of carrier profiling tools, Nanopotentiometry, analysis of device characteristics and simulations is required to provide a complete characterization of deep submicron devices.

Highly efficient and concentration-insensitive organic light-emitting devices based on self-quenching-resistant orange–red iridium complex

Energy Technology Data Exchange (ETDEWEB)

Qi, Yige; Wang, Xu [State Key Laboratory of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China); Li, Ming [College of Chemistry, Sichuan University, Chengdu 610064 (China); Lu, Zhiyun, E-mail: luzhiyun@scu.edu.cn [College of Chemistry, Sichuan University, Chengdu 610064 (China); Yu, Junsheng, E-mail: jsyu@uestc.edu.cn [State Key Laboratory of Electronic Thin Films and Integrated Devices, School of Optoelectronic Information, University of Electronic Science and Technology of China (UESTC), Chengdu 610054 (China)

2014-11-15

Orange–red phosphorescent organic light-emitting devices (PHOLEDs) with high efficiency and concentration insensitivity based on a novel iridium complex, bis[2-(biphenyl-4-yl)benzothiazole-N,C{sup 2}′]iridium(III) (acetylacetonate) [(4Phbt){sub 2}Ir(acac)], were fabricated. With the heavily doped emissive layer (EML) of 4,4′-N,N′-dicarbazolylbiphenyl (CBP): (4Phbt){sub 2}Ir(acac) in a wide and easily controlled dopant concentration range from 12 wt% to 24 wt%, a maximum power efficiency of 29 lm/W and an external quantum efficiency of >16% of the PHOLEDs were obtained, implying the insensitivity of electroluminescence (EL) properties to doping concentration. Meanwhile, a maximum power efficiency of 5.0 lm/W was achieved from a non-doped device with neat (4Phbt){sub 2}Ir(acac) as the EML, indicating a superior property of self-quenching resistance. The mechanism of direct exciton formation, in which exciton-formation regions are distributed throughout the EML, is responsible for the significant alleviation of triplet–triplet annihilation and superior EL performance. - Highlights: • Highly efficient and concentration-insensitive PHOLEDs were obtained. • The high efficiency of non-doped PHOLEDs indicated a quenching-resistant property. • The independence of EL spectra on doping concentration was observed. • The heavily doped devices were dominated by mechanism of direct exciton formation.

Nanoarchitectonics for Controlling the Number of Dopant Atoms in Solid Electrolyte Nanodots.

Science.gov (United States)

Nayak, Alpana; Unayama, Satomi; Tai, Seishiro; Tsuruoka, Tohru; Waser, Rainer; Aono, Masakazu; Valov, Ilia; Hasegawa, Tsuyoshi

2018-02-01

Controlling movements of electrons and holes is the key task in developing today's highly sophisticated information society. As transistors reach their physical limits, the semiconductor industry is seeking the next alternative to sustain its economy and to unfold a new era of human civilization. In this context, a completely new information token, i.e., ions instead of electrons, is promising. The current trend in solid-state nanoionics for applications in energy storage, sensing, and brain-type information processing, requires the ability to control the properties of matter at the ultimate atomic scale. Here, a conceptually novel nanoarchitectonic strategy is proposed for controlling the number of dopant atoms in a solid electrolyte to obtain discrete electrical properties. Using α-Ag 2+ δ S nanodots with a finite number of nonstoichiometry excess dopants as a model system, a theory matched with experiments is presented that reveals the role of physical parameters, namely, the separation between electrochemical energy levels and the cohesive energy, underlying atomic-scale manipulation of dopants in nanodots. This strategy can be applied to different nanoscale materials as their properties strongly depend on the number of doping atoms/ions, and has the potential to create a new paradigm based on controlled single atom/ion transfer. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effect of rare earth dopants on structural and mechanical properties of nanoceria synthesized by combustion method

International Nuclear Information System (INIS)

Akbari-Fakhrabadi, A.; Meruane, V.; Jamshidijam, M.; Gracia-Pinilla, M.A.; Mangalaraja, R.V.

2016-01-01

Structural characteristics of combustion synthesized, calcined and densified pure and doped nanoceria with tri-valent cations of Er, Y, Gd, Sm and Nd were analyzed by X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM). The results showed that the as-synthesized and calcined nanopowders were mesoporous and calculated lattice parameters were close to theoretical ion-packing model. The effect of dopants on elastic modulus, microhardness and fracture toughness of sintered pure and doped ceria were investigated. It was observed that tri-valent cation dopants increased the hardness of the ceria, whereas the fracture toughness and elastic modulus were decreased.

Transition Metal Dopants Essential for Producing Ferromagnetism in Metal Oxide Nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Johnson, Lydia; Thurber, Aaron P.; Anghel, Josh; Sabetian, Maryam; Engelhard, Mark H.; Tenne, D.; Hanna, Charles; Punnoose, Alex

2010-08-13

Recent claims that ferromagnetism can be produced in nanoparticles of metal oxides without the presence of transition metal dopants has been refuted in this work by investigating 62 high quality well-characterized nanoparticle samples of both undoped and Fe doped (0-10% Fe) ZnO. The undoped ZnO nanoparticles showed zero or negligible magnetization, without any dependence on the nanoparticle size. However, chemically synthesized Zn₁₋xFexO nanoparticles showed clear ferromagnetism, varying systematically with Fe concentration. Furthermore, the magnetic properties of Zn₁₋xFexO nanoparticles showed strong dependence on the reaction media used to prepare the samples. The zeta potentials of the Zn₁₋xFexO nanoparticles prepared using different reaction media were significantly different, indicating strong differences in the surface structure. Electron paramagnetic resonance studies clearly showed that the difference in the ferromagnetic properties of Zn₁₋xFexO nanoparticles with different surface structures originate from differences in the fraction of the doped Fe³⁺ ions that are coupled ferromagnetically.

Doping efficiency analysis of highly phosphorous doped epitaxial/amorphous silicon emitters grown by PECVD for high efficiency silicon solar cells

Energy Technology Data Exchange (ETDEWEB)

El-Gohary, H.G.; Sivoththaman, S. [Waterloo Univ., ON (Canada). Dept. of Electrical and Computer Engineering

2008-08-15

The efficient doping of hydrogenated amorphous and crystalline silicon thin films is a key factor in the fabrication of silicon solar cells. The most popular method for developing those films is plasma enhanced chemical vapor deposition (PECVD) because it minimizes defect density and improves doping efficiency. This paper discussed the preparation of different structure phosphorous doped silicon emitters ranging from epitaxial to amorphous films at low temperature. Phosphine (PH{sub 3}) was employed as the doping gas source with the same gas concentration for both epitaxial and amorphous silicon emitters. The paper presented an analysis of dopant activation by applying a very short rapid thermal annealing process (RTP). A spreading resistance profile (SRP) and SIMS analysis were used to detect both the active dopant and the dopant concentrations, respectively. The paper also provided the results of a structural analysis for both bulk and cross-section at the interface using high-resolution transmission electron microscopy and Raman spectroscopy, for epitaxial and amorphous films. It was concluded that a unity doping efficiency could be achieved in epitaxial layers by applying an optimized temperature profile using short time processing rapid thermal processing technique. The high quality, one step epitaxial layers, led to both high conductive and high doping efficiency layers.

On substrate dopant engineering for ET-SOI MOSFETs with UT-BOX

International Nuclear Information System (INIS)

Wu Hao; Xu Miao; Wan Guangxing; Zhu Huilong; Zhao Lichuan; Tong Xiaodong; Zhao Chao; Chen Dapeng; Ye Tianchun

2014-01-01

The importance of substrate doping engineering for extremely thin SOI MOSFETs with ultra-thin buried oxide (ES-UB-MOSFETs) is demonstrated by simulation. A new substrate/backgate doping engineering, lateral non-uniform dopant distributions (LNDD) is investigated in ES-UB-MOSFETs. The effects of LNDD on device performance, V t -roll-off, channel mobility and random dopant fluctuation (RDF) are studied and optimized. Fixing the long channel threshold voltage (V t ) at 0.3 V, ES-UB-MOSFETs with lateral uniform doping in the substrate and forward back bias can scale only to 35 nm, meanwhile LNDD enables ES-UB-MOSFETs to scale to a 20 nm gate length, which is 43% smaller. The LNDD degradation is 10% of the carrier mobility both for nMOS and pMOS, but it is canceled out by a good short channel effect controlled by the LNDD. Fixing V t at 0.3 V, in long channel devices, due to more channel doping concentration for the LNDD technique, the RDF in LNDD controlled ES-UB-MOSFETs is worse than in back-bias controlled ES-UB-MOSFETs, but in the short channel, the RDF for LNDD controlled ES-UB-MOSFET is better due to its self-adaption of substrate doping engineering by using a fixed thickness inner-spacer. A novel process flow to form LNDD is proposed and simulated. (semiconductor devices)

Self-assembling nano-diameter needlelike pinning centers in YBCO, utilizing a foreign element dopant

Energy Technology Data Exchange (ETDEWEB)

Sawh, Ravi-Persad [Texas Center for Superconductivity and Physics Department, University of Houston, 632 Science and Research Bldg 1, Houston Texas 77204-5005 (United States); Weinstein, Roy [Texas Center for Superconductivity and Physics Department, University of Houston, 632 Science and Research Bldg 1, Houston Texas 77204-5005 (United States); Obot, Victor [Department of Mathematics, Texas Southern University, 3100 Cleburne St, Houston Texas 77004-4597 (United States); Parks, Drew [Texas Center for Superconductivity and Physics Department, University of Houston, 632 Science and Research Bldg 1, Houston Texas 77204-5005 (United States); Gandini, Alberto [Texas Center for Superconductivity and Physics Department, University of Houston, 632 Science and Research Bldg 1, Houston Texas 77204-5005 (United States); Skorpenske, Harley [Texas Center for Superconductivity and Physics Department, University of Houston, 632 Science and Research Bldg 1, Houston Texas 77204-5005 (United States)

2006-06-01

Although pinning centers created by irradiation presently produce the highest J{sub c}, it is probable that ultimately these will be emulated by chemical pinning centers. The best pinning centers produced by irradiation nevertheless provide guidelines for desirable morphology of chemical pinning structures. The highest J{sub c} produced earlier in textured HTS was obtained using isotropic high-energy ions produced by fission of {sup 235}U. This so-called U/n process produces pinning centers of diameter {<=} 4.5 nm, with an effective length of {approx}2.7 {mu}m. Maximum J{sub c} occurs for pinning center density of {approx}10{sup 10} cm{sup -3}. We use this as a model for desired chemical pinning centers. Our approach to introducing chemical pinning centers has been to produce precipitates within the HTS containing elements not native to the HTS, and to seek needlelike (columnar) deposits of small diameter. We report here on the formation of needlelike or columnar deposits in textured Y123 containing a dopant foreign to Y123. It serves as a demonstration that self-assembling nanometer diameter columns utilizing a dopant foreign to the HTS system are a feasible goal. These deposits, however, do not fully meet the ultimate requirements of pinning centers because the desired deposits should be smaller. The self-assembling columns formed contain titanium, are {approx}500 nm in diameter, and up to 10 {mu}m long. The size and morphology of the deposits vary with the mass of admixed Ti dopant. J{sub c} is decreased for small dopant mass. At larger dopant masses needlelike precipitates form, and J{sub c} increases again. A small range of mass of admixed Ti exists in which J{sub c} is enhanced by pinning. In the range of admixed Ti mass studied in these experiments there is a negligible effect on T{sub c}. Magnetization studies of J{sub c} are also reported.

Dopant-assisted negative photoionization Ion mobility spectrometry coupled with on-line cooling inlet for real-time monitoring H2S concentration in sewer gas.

Science.gov (United States)

Peng, Liying; Jiang, Dandan; Wang, Zhenxin; Hua, Lei; Li, Haiyang

2016-06-01

Malodorous hydrogen sulfide (H2S) gas often exists in the sewer system and associates with the problems of releasing the dangerous odor to the atmosphere and causing sewer pipe to be corroded. A simple method is in demand for real-time measuring H2S level in the sewer gas. In this paper, an innovated method based on dopant-assisted negative photoionization ion mobility spectrometry (DANP-IMS) with on-line semiconductor cooling inlet was put forward and successfully applied for the real-time measurement of H2S in sewer gas. The influence of moisture was effectively reduced via an on-line cooling method and a non-equilibrium dilution with drift gas. The limits of quantitation for the H2S in ≥60% relative humidity air could be obtained at ≤79.0ng L(-1) with linear ranges of 129-2064ng L(-1). The H2S concentration in a sewer manhole was successfully determined while its product ions were identified by an ion-mobility time-of-fight mass spectrometry. Finally, the correlation between sewer H2S concentration and the daily routines and habits of residents was investigated through hourly or real-time monitoring the variation of sewer H2S in manholes, indicating the power of this DANP-IMS method in assessing the H2S concentration in sewer system. Copyright © 2016 Elsevier B.V. All rights reserved.

Dopant Adsorption and Incorporation at Irradiated GaN Surfaces

Science.gov (United States)

Sun, Qiang; Selloni, Annabella; Myers, Thomas; Doolittle, W. Alan

2006-03-01

Mg and O are two of the common dopants in GaN, but, in spite of extensive investigation, the atomic scale understanding of their adsorption and incorporation is still incomplete. In particular, high-energy electron irradiation, such as occurring during RHEED, has been reported to have an important effect on the incorporation of these impurities, but no study has addressed the detailed mechanisms of this effect yet. Here we use DFT calculations to study the adsorption and incorporation of Mg and O at the Ga- and N-polar GaN surfaces under various Ga, Mg and O coverage conditions as well as in presence of light or electron beam-induced electronic excitation. We find that the adsorption and incorporation of the two impurities have opposite surface polarity dependence: substitutional Mg prefers to incorporate at the GaN(0001) surface, while O prefers to adsorb and incorporate at the N-polar surface. In addition, our results indicate that in presence of light irradiation the tendency of Mg to surface-segregate is reduced. The O adsorption energy on the N-polar surface is also significantly reduced, consistent with the experimental observation of a much smaller concentration of oxygen in the irradiated samples.

Model of dopant action in oxide cathodes

International Nuclear Information System (INIS)

Engelsen, Daniel den; Gaertner, Georg

2005-01-01

The paper describes an electrochemical model, which largely explains the formation of Ba in the oxide cathode at activation and normal operation. In a non-doped oxide cathode electrolysis of BaO is, besides the exchange reaction from the activators in the cathode nickel, an important source of Ba. By doping with rare earth oxides the conductivity of the oxide layer increases, which implies that the potential difference during current drawing over the oxide layer becomes lower and electrolysis of BaO is suppressed. This implies that the part of the electronic conductivity of the (Ba,Sr)O layer induced by the dopants also controls the sensitivity for poisoning: the higher the dopant level, the larger the sensitivity for poisoning. Furthermore, the suppression of electrolysis during normal operation largely explains why doped oxide cathodes have a better life performance than non-doped cathodes. Finally a hypothesis on the enhancement of sintering upon doping is presented

Dopant effects on charge transport to enhance performance of phosphorescent white organic light emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Zhu, Liping; Chen, Jiangshan; Ma, Dongge, E-mail: mdg1014@ciac.ac.cn [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, University of Chinese Academy of Sciences, Changchun 130022 (China)

2015-11-07

We compared the performance of phosphorescent white organic light emitting diodes (WOLEDs) with red-blue-green and green-blue-red sequent emissive layers. It was found that the influence of red and green dopants on electron and hole transport in emissive layers leads to the large difference in the efficiency of fabricated WOLEDs. This improvement mechanism is well investigated by the current density-voltage characteristics of single-carrier devices based on dopant doped emissive layers and the comparison of electroluminescent and photoluminescence spectra, and attributed to the different change of charge carrier transport by the dopants. The optimized device achieves a maximum power efficiency, current efficiency, and external quantum efficiency of 37.0 lm/W, 38.7 cd/A, and 17.7%, respectively, which are only reduced to 32.8 lm/W, 38.5 cd/A, and 17.3% at 1000 cd/m{sup 2} luminance. The critical current density is as high as 210 mA/cm{sup 2}. It can be seen that the efficiency roll-off in phosphorescent WOLEDs can be well improved by effectively designing the structure of emissive layers.

Invalidity of the Fermi liquid theory and magnetic phase transition in quasi-1D dopant-induced armchair-edged graphene nanoribbons

Science.gov (United States)

Hoi, Bui Dinh; Davoudiniya, Masoumeh; Yarmohammadi, Mohsen

2018-04-01

Based on theoretically tight-binding calculations considering nearest neighbors and Green's function technique, we show that the magnetic phase transition in both semiconducting and metallic armchair graphene nanoribbons with width ranging from 9.83 Å to 69.3 Å would be observed in the presence of injecting electrons by doping. This transition is explained by the temperature-dependent static charge susceptibility through calculation of the correlation function of charge density operators. This work showed that charge concentration of dopants in such system plays a crucial role in determining the magnetic phase. A variety of multicritical points such as transition temperatures and maximum susceptibility are compared in undoped and doped cases. Our findings show that there exist two different transition temperatures and maximum susceptibility depending on the ribbon width in doped structures. Another remarkable point refers to the invalidity (validity) of the Fermi liquid theory in nanoribbons-based systems at weak (strong) concentration of dopants. The obtained interesting results of magnetic phase transition in such system create a new potential for magnetic graphene nanoribbon-based devices.

Spectroscopic diagnostics of NIF ICF implosions using line ratios of Kr dopant in the ignition capsule

Science.gov (United States)

Dasgupta, Arati; Ouart, Nicholas; Giuiani, John; Clark, Robert; Schneider, Marilyn; Scott, Howard; Chen, Hui; Ma, Tammy

2017-10-01

X ray spectroscopy is used on the NIF to diagnose the plasma conditions in the ignition target in indirect drive ICF implosions. A platform is being developed at NIF where small traces of krypton are used as a dopant to the fuel gas for spectroscopic diagnostics using krypton line emissions. The fraction of krypton dopant was varied in the experiments and was selected so as not to perturb the implosion. Our goal is to use X-ray spectroscopy of dopant line ratios produced by the hot core that can provide a precise measurement of electron temperature. Simulations of the krypton spectra using a 1 in 104 atomic fraction of krypton in direct-drive exploding pusher with a range of electron temperatures and densities show discrepancies when different atomic models are used. We use our non-LTE atomic model with a detailed fine-structure level atomic structure and collisional-radiative rates to investigate the krypton spectra at the same conditions. Synthetic spectra are generated with a detailed multi-frequency radiation transport scheme from the emission regions of interest to analyze the experimental data with 0.02% Kr concentration and compare and contrast with the existing simulations at LLNL. Work supported by DOE/NNSA; Part of this work was also done under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract No. DE-AC52-07NA27344.

Preparation and characterization of electrodeposited SnS:In thin films: Effect of In dopant

Science.gov (United States)

Kafashan, Hosein; Balak, Zohre

2017-09-01

SnS:In thin films were grown on fluorine doped tin oxide (FTO) substrate by cathodic electrodeposition technique. The solution was containing 2 mM SnCl2 and 16 mM Na2S2O3 and different amounts of 1 mM InCl3 as In-dopant. The pH, bath temperature, deposition time, and deposition potential (E) were fixed at 2.1, 60 °C, 30 min, and - 1 V, respectively. The XRD results showed that the synthesized films were polycrystalline orthorhombic SnS. The XPS results demonstrated that the films were composed of Sn, S and In. According to the FESEM images, an increase in In-dopant concentration leads to a change in morphology from grain-like to sheet-like having a nanoscale thickness of 20-80 nm and fiber-like. The PL spectra of undoped SnS exhibited four emission peaks including a UV peak, two blue emission peaks, and an IR emission peak. According to the UV-Vis spectra, the direct band gap of SnS:In thin films was estimated to be 1.40-1.66 eV.

Bistable Si dopants in the GaAs (1 1 0) surface

International Nuclear Information System (INIS)

Smakman, E P; Koenraad, P M

2015-01-01

In this review, recent work is discussed on bistable Si dopants in the GaAs (1 1 0) surface, studied by scanning tunneling microscopy (STM). The bistability arises because the dopant atom can switch between a positive and a negative charge state, which are associated with two different lattice configurations. Manipulation of the Si atom charge configuration is achieved by tuning the local band bending with the STM tip. Furthermore, illuminating the sample with a laser also influences the charge state, allowing the operation of the dopant atom as an optical switch. The switching dynamics without illumination is investigated in detail as a function of temperature, lateral tip position, and applied tunneling conditions. A physical model is presented that independently describes the thermal and quantum tunneling contributions to the switching frequency and charge state occupation of a single Si atom. The basic functionality of a memory cell is demonstrated employing a single bistable Si dopant as the active element, using the STM tip as a gate to write and read the information. (topical review)

Impact of dopant profiles on the end of range defects for low energy germanium preamorphized silicon

International Nuclear Information System (INIS)

Camillo-Castillo, R.A.; Law, M.E.; Jones, K.S.

2004-01-01

As the industry continues to aggressively scale CMOS technology, the shift to lower energy ion implantation becomes essential. The consequent shallower amorphous layers result in dopant profiles that are in closer proximity to the end of range (EOR) damage and therefore a better understanding of the interaction between the dopant atoms and the EOR is required. A study is conducted on the influence of dopant profiles on the behavior of the EOR defects. Czochralski-grown silicon wafers are preamorphized with 1 x 10 15 cm -2 , 10 keV Ge + ions and subsequently implanted with 1 x 10 15 cm -2 , 1 keV B + ions. A sequence of rapid thermal and furnace anneals are performed at 750 deg. C under a nitrogen ambient for periods of 1 s up to 6 h. Plan view transmission electron microscopy (PTEM) reveals a significant difference in the defect evolution for samples with and without boron, suggesting that the boron influences the evolution of the EOR defects. The extended defects observed for samples which contain boron appear as dot-like defects which are unstable and dissolve after very short anneal times. The defect evolution however, in samples without boron follows an Oswald ripening behavior and form {3 1 1}-type defects and dislocation loops. Hall effect measurements denote a high initial activation and subsequent deactivation of the dopant atoms which is characteristic of the formation of boron interstitial clusters. Diffusion analyses via secondary ion mass spectroscopy (SIMS) support this theory

Effects of small-angle mistilts on dopant visibility in ADF-STEM imaging of nanocrystals

Energy Technology Data Exchange (ETDEWEB)

Held, Jacob T.; Duncan, Samuel; Mkhoyan, K. Andre, E-mail: mkhoyan@umn.edu

2017-06-15

Highlights: • ADF-STEM is powerful technique for 3D location of substitutionally doped atoms. • The effects of specimen mistilt on ADF-STEM imaging of doped atoms are evaluated. • Visibility changes over 0–30 mrad mistilts are large enough to preclude 3D dopant location. • Dopant visibility is a strong function of specimen mistilt and cannot be ignored. - Abstract: Quantitative ADF-STEM imaging paired with image simulations has proven to be a powerful technique for determining the three dimensional location of substitutionally doped atoms in thin films. Expansion of this technique to lightly-doped nanocrystals requires an understanding of the influence of specimen mistilt on dopant visibility due to the difficulty of accurate orientation determination in such systems as well as crystal movement under the beam. In this study, the effects of specimen mistilt on ADF-STEM imaging are evaluated using germanium-doped silicon nanocrystals as model systems. It is shown that dopant visibility is a strong function of specimen mistilt, and the accuracy of specimen orientation is an important factor in the analysis of three-dimensional dopant location, but the sensitivity to mistilt can be weakened by increasing the STEM probe convergence angle and optimizing ADF detector inner angle.

Planar Perovskite Solar Cells with High Open-Circuit Voltage Containing a Supramolecular Iron Complex as Hole Transport Material Dopant.

Science.gov (United States)

Saygili, Yasemin; Turren-Cruz, Silver-Hamill; Olthof, Selina; Saes, Bartholomeus Wilhelmus Henricus; Pehlivan, Ilknur Bayrak; Saliba, Michael; Meerholz, Klaus; Edvinsson, Tomas; Zakeeruddin, Shaik M; Grätzel, Michael; Correa-Baena, Juan-Pablo; Hagfeldt, Anders; Freitag, Marina; Tress, Wolfgang

2018-04-26

In perovskite solar cells (PSCs), the most commonly used hole transport material (HTM) is spiro-OMeTAD, which is typically doped by metalorganic complexes, for example, based on Co, to improve charge transport properties and thereby enhance the photovoltaic performance of the device. In this study, we report a new hemicage-structured iron complex, 1,3,5-tris(5'-methyl-2,2'-bipyridin-5-yl)ethylbenzene Fe(III)-tris(bis(trifluoromethylsulfonyl)imide), as a p-type dopant for spiro-OMeTAD. The formal redox potential of this compound was measured as 1.29 V vs. the standard hydrogen electrode, which is slightly (20 mV) more positive than that of the commercial cobalt dopant FK209. Photoelectron spectroscopy measurements confirm that the iron complex acts as an efficient p-dopant, as evidenced in an increase of the spiro-OMeTAD work function. When fabricating planar PSCs with the HTM spiro-OMeTAD doped by 5 mol % of the iron complex, a power conversion efficiency of 19.5 % (AM 1.5G, 100 mW cm -2 ) is achieved, compared to 19.3 % for reference devices with FK209. Open circuit voltages exceeding 1.2 V at 1 sun and reaching 1.27 V at 3 suns indicate that recombination at the perovskite/HTM interface is low when employing this iron complex. This work contributes to recent endeavors to reduce recombination losses in perovskite solar cells. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

The Effect of Acceptor and Donor Doping on Oxygen Vacancy Concentrations in Lead Zirconate Titanate (PZT).

Science.gov (United States)

Slouka, Christoph; Kainz, Theresa; Navickas, Edvinas; Walch, Gregor; Hutter, Herbert; Reichmann, Klaus; Fleig, Jürgen

2016-11-22

The different properties of acceptor-doped (hard) and donor-doped (soft) lead zirconate titanate (PZT) ceramics are often attributed to different amounts of oxygen vacancies introduced by the dopant. Acceptor doping is believed to cause high oxygen vacancy concentrations, while donors are expected to strongly suppress their amount. In this study, La 3+ donor-doped, Fe 3+ acceptor-doped and La 3+ /Fe 3+ -co-doped PZT samples were investigated by oxygen tracer exchange and electrochemical impedance spectroscopy in order to analyse the effect of doping on oxygen vacancy concentrations. Relative changes in the tracer diffusion coefficients for different doping and quantitative relations between defect concentrations allowed estimates of oxygen vacancy concentrations. Donor doping does not completely suppress the formation of oxygen vacancies; rather, it concentrates them in the grain boundary region. Acceptor doping enhances the amount of oxygen vacancies but estimates suggest that bulk concentrations are still in the ppm range, even for 1% acceptor doping. Trapped holes might thus considerably contribute to the charge balancing of the acceptor dopants. This could also be of relevance in understanding the properties of hard and soft PZT.

The Effect of Acceptor and Donor Doping on Oxygen Vacancy Concentrations in Lead Zirconate Titanate (PZT

Directory of Open Access Journals (Sweden)

Christoph Slouka

2016-11-01

Full Text Available The different properties of acceptor-doped (hard and donor-doped (soft lead zirconate titanate (PZT ceramics are often attributed to different amounts of oxygen vacancies introduced by the dopant. Acceptor doping is believed to cause high oxygen vacancy concentrations, while donors are expected to strongly suppress their amount. In this study, La3+ donor-doped, Fe3+ acceptor-doped and La3+/Fe3+-co-doped PZT samples were investigated by oxygen tracer exchange and electrochemical impedance spectroscopy in order to analyse the effect of doping on oxygen vacancy concentrations. Relative changes in the tracer diffusion coefficients for different doping and quantitative relations between defect concentrations allowed estimates of oxygen vacancy concentrations. Donor doping does not completely suppress the formation of oxygen vacancies; rather, it concentrates them in the grain boundary region. Acceptor doping enhances the amount of oxygen vacancies but estimates suggest that bulk concentrations are still in the ppm range, even for 1% acceptor doping. Trapped holes might thus considerably contribute to the charge balancing of the acceptor dopants. This could also be of relevance in understanding the properties of hard and soft PZT.

Profiling N-Type Dopants in Silicon

Czech Academy of Sciences Publication Activity Database

Hovorka, Miloš; Mika, Filip; Mikulík, P.; Frank, Luděk

2010-01-01

Roč. 51, č. 2 (2010), s. 237-242 ISSN 1345-9678 R&D Projects: GA ČR GP102/09/P543; GA AV ČR IAA100650803 Institutional research plan: CEZ:AV0Z20650511 Keywords : silicon * dopant contrast * photoemission electron microscopy * scanning electron microscopy Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering Impact factor: 0.779, year: 2010 http://www.jim.or.jp/journal/e/51/02/237.html

Addition of photosensitive dopants to the D0 liquid argon calorimeter

International Nuclear Information System (INIS)

Amos, N.A.; Anderson, D.F.

1992-10-01

The addition of photosensitive dopants to liquid argon greatly enhances the signal from heavily ionizing particles. Since binding energy losses we correlated with the heavily ionizing component in hadronic showers, the addition of photosensitive dopants has been suggested as a mechanism to tune the e/π ratio in liquid argon calorimeters. A measurement was performed at the FNAL test beam, adding 4 ppM tetramethylgermanium to the Dφ uranium-liquid argon calorimeter. An increase in response for electromagnetic and hadronic showers was observed, with no net change in the e/π ratio

Solution-processed organic thermoelectric materials exhibiting doping-concentration-dependent polarity.

Science.gov (United States)

Hwang, Sunbin; Potscavage, William J; Yang, Yu Seok; Park, In Seob; Matsushima, Toshinori; Adachi, Chihaya

2016-10-26

Recent progress in conducting polymer-based organic thermoelectric generators (OTEGs) has resulted in high performance due to high Seebeck coefficient, high electrical conductivity (σ), and low thermal conductivity obtained by chemically controlling the materials's redox levels. In addition to improving the properties of individual OTEGs to obtain high performance, the development of solution processes for the fabrication of OTEG modules is necessary to realize large thermoelectric voltage and low-cost mass production. However, the scarcity of good candidates for soluble organic n-type materials limits the use of π-leg module structures consisting of complementary elements of p- and n-type materials because of unbalanced transport coefficients that lead to power losses. In particular, the extremely low σ of n-type materials compared with that of p-type materials is a serious challenge. In this study, poly(pyridinium phenylene) (P(PymPh)) was tested as an n-type semiconductor in solution-processed OTEGs, and the carrier density was controlled by a solution-based chemical doping process using the dopant sodium naphthalenide, a well-known reductant. The electronic structures and doping mechanism of P(PymPh) were explored based on the changes in UV-Vis-IR absorption, ultraviolet photoelectron, and X-ray photoelectron spectra. By controlling the dopant concentration, we demonstrate a maximum n-type power factor of 0.81 μW m -1 K -2 with high σ, and at higher doping concentrations, a switch from n-type to p-type TE operation. This is one of the first cases of a switch in polarity just by increasing the concentration of the reductant and may open a new route for simplified fabrication of complementary organic layers.

Magnetoresistance and charge transport in graphene governed by nitrogen dopants.

Science.gov (United States)

Rein, Markus; Richter, Nils; Parvez, Khaled; Feng, Xinliang; Sachdev, Hermann; Kläui, Mathias; Müllen, Klaus

2015-02-24

We identify the influence of nitrogen-doping on charge- and magnetotransport of single layer graphene by comparing doped and undoped samples. Both sample types are grown by chemical vapor deposition (CVD) and transferred in an identical process onto Si/SiO2 wafers. We characterize the samples by Raman spectroscopy as well as by variable temperature magnetotransport measurements. Over the entire temperature range, the charge transport properties of all undoped samples are in line with literature values. The nitrogen doping instead leads to a 6-fold increase in the charge carrier concentration up to 4 × 10(13) cm(-2) at room temperature, indicating highly effective doping. Additionally it results in the opening of a charge transport gap as revealed by the temperature dependence of the resistance. The magnetotransport exhibits a conspicuous sign change from positive Lorentz magnetoresistance (MR) in undoped to large negative MR that we can attribute to the doping induced disorder. At low magnetic fields, we use quantum transport signals to quantify the transport properties. Analyses based on weak localization models allow us to determine an orders of magnitude decrease in the phase coherence and scattering times for doped samples, since the dopants act as effective scattering centers.

Dopant-Free and Carrier-Selective Heterocontacts for Silicon Solar Cells: Recent Advances and Perspectives.

Science.gov (United States)

Gao, Pingqi; Yang, Zhenhai; He, Jian; Yu, Jing; Liu, Peipei; Zhu, Juye; Ge, Ziyi; Ye, Jichun

2018-03-01

By combining the most successful heterojunctions (HJ) with interdigitated back contacts, crystalline silicon (c-Si) solar cells (SCs) have recently demonstrated a record efficiency of 26.6%. However, such SCs still introduce optical/electrical losses and technological issues due to parasitic absorption/Auger recombination inherent to the doped films and the complex process of integrating discrete p + - and n + -HJ contacts. These issues have motivated the search for alternative new functional materials and simplified deposition technologies, whereby carrier-selective contacts (CSCs) can be formed directly with c-Si substrates, and thereafter form IBC cells, via a dopant-free method. Screening and modifying CSC materials in a wider context is beneficial for building dopant-free HJ contacts with better performance, shedding new light on the relatively mature Si photovoltaic field. In this review, a significant number of achievements in two representative dopant-free hole-selective CSCs, i.e . , poly(3,4-ethylene dioxythiophene):poly(styrenesulfonate)/Si and transition metal oxides/Si, have been systemically presented and surveyed. The focus herein is on the latest advances in hole-selective materials modification, interfacial passivation, contact resistivity, light-trapping structure and device architecture design, etc. By analyzing the structure-property relationships of hole-selective materials and assessing their electrical transport properties, promising functional materials as well as important design concepts for such CSCs toward high-performance SCs have been highlighted.

Carrier transport assisted by dopants in doped poly(N-vinylcarbozole) light-emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Chen Xiaohong [Institute of Optoelectronic Technology, Bejing Jiaotong University, Beijing 100044 (China); Liu Ming [Institute of Optoelectronic Technology, Bejing Jiaotong University, Beijing 100044 (China); Xu Zheng [Institute of Optoelectronic Technology, Bejing Jiaotong University, Beijing 100044 (China); Hou Yanbing [Institute of Optoelectronic Technology, Bejing Jiaotong University, Beijing 100044 (China); Teng Feng [Institute of Optoelectronic Technology, Bejing Jiaotong University, Beijing 100044 (China); Xu Xurong [Institute of Optoelectronic Technology, Bejing Jiaotong University, Beijing 100044 (China)

2004-04-07

We have investigated the transient electroluminescence (EL) onset of the double-layer light-emitting devices made from poly(N-vinylcarbozole) (PVK) doped with 4-(dicyanomethylene)-2-t-butyl-6(1, 1, 7, 7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB) and tris(8-hydroxy-quinoline) aluminium (Alq{sub 3}). For the double-layered device in which PVK was doped with 0.1 wt% DCJTB, the EL onset of PVK lags that of DCJTB and Alq{sub 3}, while the EL onset of DCJTB and Alq{sub 3} is simultaneous. However, the EL emission of the double-layered device of PVK/Alq{sub 3} originates only from Alq{sub 3}. The results show that DCJTB dopants can not only help to tunnel electrons from Alq{sub 3} zone to PVK but can also assist electrons transfer in PVK under high electric field by hopping between DCJTB molecules or from DCJTB to PVK sites at a low doping concentration of 0.1 wt%. When the DCJTB doping concentration is 4.0 wt%, the EL onset of Alq{sub 3} lags that of DCJTB. The difference in the EL onsets of DCJTB, Alq{sub 3} and PVK is attributed to the slow build-up of the internal space charge in the vicinity of the interface between PVK and Alq{sub 3}. The electron potential difference of the interface between Alq{sub 3} and PVK doped by DCJTB can be adjusted by changing the DCJTB doping concentration in double-layer devices.

Influence of Ni-dopant on the properties of synthetic goethite

International Nuclear Information System (INIS)

Krehula, Stjepko; Music, Svetozar; Popovic, Stanko

2005-01-01

The influence of Ni-dopant on the properties of α-FeOOH was investigated by XRD, FT-IR, 57 Fe Moessbauer spectroscopy and transmission electron microscopy. α-FeOOH was synthesized at a highly alkaline pH by precipitation from the FeCl 3 solution with the addition of tetramethylammonium hydroxide and autoclaving at 160 o C. The samples doped with Ni 2+ ions were precipitated in the same way, but in the presence of varying concentrations of NiCl 2 . Solid solutions, having the structure of α-FeOOH, were observed in samples with the Ni/Fe ratio up to 0.05. Upon increasing the amount of Ni-dopant the XRD lines were gradually broadened. The sample with the ratio Ni/Fe=0.10 showed NiFe 2 O 4 , besides the dominant phase having the structure type of α-FeOOH. Shifts of IR bands at 892 and 796cm -1 were not observed in all samples doped with Ni. For the ratio Ni/Fe=0.10, the IR bands centered at 631 and 404cm -1 were significantly broadened. RT Moessbauer spectrum of undoped α-FeOOH and Ni-doped α-FeOOH showed distributions of hyperfine magnetic fields. B hf decreased from 35.1T for an undoped α-FeOOH to 32.1T for α-FeOOH containing Ni 2+ ions (Ni/Fe=0.05). The saturation of the α-FeOOH structure with Ni 2+ ions in amounts higher than ∼5mol% was also observed by Moessbauer spectroscopy. The particle size (length) of acicular α-FeOOH particles with a maximum in the interval 180-220nm was slightly decreased with Ni-doping, but the distribution of the length/width ratio showed no change, having a maximum at 4-5. TEM photographs additionally showed small populations of cubic-shaped or pseudocubic particles of ∼10nm in size for the ratio Ni/Fe=0.05 and about 10-20nm in size for the ratio Ni/Fe=0.10. These particles were assigned to NiFe 2 O 4

Observation of two-dimensional p-type dopant diffusion across a p+-InP/n–-InGaAs interface using scanning electron microscopy

International Nuclear Information System (INIS)

Tsurumi, Daisuke; Hamada, Kotaro; Kawasaki, Yuji

2013-01-01

Scanning electron microscopy (SEM) with potential calculations has been shown to be effective for the detection of p-type dopant diffusion, even across a Zn doped p + -InP/non-doped n – -InGaAs/n + -InP heterojunction. Heterojunction samples were observed using SEM and the electrostatic potential was calculated from Zn concentration profiles obtained by secondary ion mass spectrometry. The sensitivity of SEM for the potential was derived from the SEM observations and potential calculation results. The results were then used to investigate the dependence of the SEM contrast on the Zn diffusion length across the p + -InP/non-doped n – -InGaAs interface. Accurate dopant mapping was difficult when the Zn diffusion length was shorter than 30 nm, because the heterojunction affects the potential at the interface. However, accurate dopant mapping was possible when the Zn diffusion length was longer than 30 nm, because the factor dominating the potential variation was not the heterojunction, but rather Zn diffusion 30 nm distant from the interface. Thus, Zn diffusion further than 30 nm from a Zn-doped p + -InP/non-doped n – -InGaAs interface can be effectively detected by secondary electron (SE) imaging. SE imaging with potential calculations can be widely used for accurate dopant mapping, even at heterojunctions, and is, therefore, expected to be of significant assistance to the compound semiconductor industry.

Quantified Hole Concentration in AlGaN Nanowires for High-Performance Ultraviolet Emitters

KAUST Repository

Zhao, Chao; Ebaid, Mohamed; Zhang, Huafan; Priante, Davide; Janjua, Bilal; Zhang, Daliang; Wei, Nini; Alhamoud, Abdullah; Shakfa, M. Khaled; Ng, Tien Khee; Ooi, Boon S.

2018-01-01

P-type doping in wide bandgap and new classes of ultra-wide bandgap materials has long been a scientific and engineering problem. The challenges arise from the large activation energy of dopants and high densities of dislocations in materials. We report here, a significantly enhanced p-type conduction using high-quality AlGaN nanowires. For the first time, the hole concentration in Mg-doped AlGaN nanowires is quantified. The incorporation of Mg into AlGaN was verified by correlation with photoluminescence and Raman measurements. The open-circuit potential measurements further confirmed the p-type conductivity; while Mott-Schottky experiments measured a hole concentration of 1.3×1019 cm-3. These results from photoelectrochemical measurements allow us to design prototype ultraviolet (UV) light-emitting diodes (LEDs) incorporating the AlGaN quantum-disks-in-nanowire and optimized p-type AlGaN contact layer for UV-transparency. The ~335-nm LEDs exhibited a low turn-on voltage of 5 V with a series resistance of 32 Ω, due to the efficient p-type doping of the AlGaN nanowires. The bias-dependent Raman measurements further revealed the negligible self-heating of devices. This study provides an attractive solution to evaluate electrical properties of AlGaN, which is applicable to other wide bandgap nanostructures. Our results are expected to open doors to new applications for wide and ultra-wide bandgap materials.

Quantified Hole Concentration in AlGaN Nanowires for High-Performance Ultraviolet Emitters

KAUST Repository

Zhao, Chao

2018-05-29

P-type doping in wide bandgap and new classes of ultra-wide bandgap materials has long been a scientific and engineering problem. The challenges arise from the large activation energy of dopants and high densities of dislocations in materials. We report here, a significantly enhanced p-type conduction using high-quality AlGaN nanowires. For the first time, the hole concentration in Mg-doped AlGaN nanowires is quantified. The incorporation of Mg into AlGaN was verified by correlation with photoluminescence and Raman measurements. The open-circuit potential measurements further confirmed the p-type conductivity; while Mott-Schottky experiments measured a hole concentration of 1.3×1019 cm-3. These results from photoelectrochemical measurements allow us to design prototype ultraviolet (UV) light-emitting diodes (LEDs) incorporating the AlGaN quantum-disks-in-nanowire and optimized p-type AlGaN contact layer for UV-transparency. The ~335-nm LEDs exhibited a low turn-on voltage of 5 V with a series resistance of 32 Ω, due to the efficient p-type doping of the AlGaN nanowires. The bias-dependent Raman measurements further revealed the negligible self-heating of devices. This study provides an attractive solution to evaluate electrical properties of AlGaN, which is applicable to other wide bandgap nanostructures. Our results are expected to open doors to new applications for wide and ultra-wide bandgap materials.

Controlled light emission from white organic light-emitting devices with a single blue-emitting host and multiple fluorescent dopants

International Nuclear Information System (INIS)

Chin, Byung Doo; Kim, Jai Kyeong; Park, O Ok

2007-01-01

In this work, we fabricated white organic light-emitting devices (WOLEDs) containing a layered light-emitting region composed of a single blue-emitting host and different fluorescent dopant materials. The effects of varying the dye-doping ratio and emitting layer thickness on the efficiency, lifetime, spectral voltage-dependence and white balance were investigated for devices with a blue/orange stacked layer structure. Addition of a blue host layer doped with a green-emitting dopant, to give a blue/green/orange emitter, resulted in a broadband white spectrum without the need for a charge-blocking interlayer. The composition of blue, green and orange dopants in the host and the thickness of each emitting layer were optimized, resulting in a device efficiency of 9-11 cd A -1 even at a high brightness of 10 000 cd m -2 (achieved at a bias voltage of less than 9 V) with an emission spectrum suitable for lighting applications

Metal oxalate complexes as novel inorganic dopants: Studies on ...

Indian Academy of Sciences (India)

Unknown

UV-visible and IR spectral features not only confirmed the polyaniline doping by complex anions but also substantiated ... MoS3 dopant. Although inorganic metal complexes bear- ... distilled water and then with methanol and acetone until.

Controlling energy transfer between multiple dopants within a single nanoparticle

Science.gov (United States)

DiMaio, Jeffrey R.; Sabatier, Clément; Kokuoz, Baris; Ballato, John

2008-01-01

Complex core-shell architectures are implemented within LaF3 nanoparticles to allow for a tailored degree of energy transfer (ET) between different rare earth dopants. By constraining specific dopants to individual shells, their relative distance to one another can be carefully controlled. Core-shell LaF3 nanoparticles doped with Tb3+ and Eu3+ and consisting of up to four layers were synthesized with an outer diameter of ≈10 nm. It is found that by varying the thicknesses of an undoped layer between a Tb3+-doped layer and a Eu3+-doped layer, the degree of ET can be engineered to allow for zero, partial, or total ET from a donor ion to an acceptor ion. More specifically, the ratio of the intensities of the 541-nm Tb3+ and 590 nm Eu3+ peaks was tailored from core-shell configuration that restricts ET is used. Beyond simply controlling ET, which can be limiting when designing materials for optical applications, this approach can be used to obtain truly engineered spectral features from nanoparticles and composites made from them. Further, it allows for a single excitation source to yield multiple discrete emissions from numerous lanthanide dopants that heretofore would have been quenched in a more conventional active optical material. PMID:18250307

Titanium dioxide nanotube membranes for solar energy conversion: effect of deep and shallow dopants.

Science.gov (United States)

Ding, Yuchen; Nagpal, Prashant

2017-04-12

Nanostructured titanium dioxide (TiO 2 ) has been intensively investigated as a material of choice for solar energy conversion in photocatalytic, photoelectrochemical, photovoltaic, and other photosensitized devices for converting light into chemical feedstocks or electricity. Towards management of light absorption in TiO 2 , while the nanotubular structure improves light absorption and simultaneous charge transfer to mitigate problems due to the indirect bandgap of the semiconductor, typically dopants are used to improve light absorption of incident solar irradiation in the wide bandgap of TiO 2 . While these dopants can be critical to the success of these solar energy conversion devices, their effect on photophysical and photoelectrochemical properties and detailed photokinetics are relatively under-studied. Here, we show the effect of deep and shallow metal dopants on the kinetics of photogenerated charged carriers in TiO 2 and the resulting effect on photocatalytic and photoelectrochemical processes using these nanotube membranes. We performed a detailed optical, electronic, voltammetry and electrochemical impedance study to understand the effect of shallow and deep metal dopants (using undoped and niobium- and copper-doped TiO 2 nanotubes) on light absorption, charge transport and charge transfer processes. Using wireless photocatalytic methylene blue degradation and carbon dioxide reduction, and wired photoelectrochemical device measurements, we elucidate the effect of different dopants on solar-to-fuel conversion efficiency and simultaneously describe the photokinetics using a model, to help design better energy conversion devices.

Molecular Electrical Doping of Organic Semiconductors: Fundamental Mechanisms and Emerging Dopant Design Rules.

Science.gov (United States)

Salzmann, Ingo; Heimel, Georg; Oehzelt, Martin; Winkler, Stefanie; Koch, Norbert

2016-03-15

-Dirac occupation of which ultimately determines the doping efficiency, thus emerges as key challenge. As a first step, the formation of charge transfer complexes is identified as being detrimental to the doping efficiency, which suggests sterically shielding the functional core of dopant molecules as an additional design rule to complement the requirement of low ionization energies or high electron affinities in efficient n-type or p-type dopants, respectively. In an extended outlook, we finally argue that, to fully meet this challenge, an improved understanding is required of just how the admixture of dopant molecules to organic semiconductors does affect the density of states: compared with their inorganic counterparts, traps for charge carriers are omnipresent in organic semiconductors due to structural and chemical imperfections, and Coulomb attraction between ionized dopants and free charge carriers is typically stronger in organic semiconductors owing to their lower dielectric constant. Nevertheless, encouraging progress is being made toward developing a unifying picture that captures the entire range of doping induced phenomena, from ion-pair to complex formation, in both conjugated polymers and molecules. Once completed, such a picture will provide viable guidelines for synthetic and supramolecular chemistry that will enable further technological advances in organic and hybrid organic/inorganic devices.

Quantitative dopant profiling in semiconductors. A new approach to Kelvin probe force microscopy

Energy Technology Data Exchange (ETDEWEB)

Baumgart, Christine

2012-07-01

Failure analysis and optimization of semiconducting devices request knowledge of their electrical properties. To meet the demands of today's semiconductor industry, an electrical nanometrology technique is required which provides quantitative information about the doping profile and which enables scans with a lateral resolution in the sub-10 nm range. In the presented work it is shown that Kelvin probe force microscopy (KPFM) is a very promising electrical nanometrology technique to face this challenge. The technical and physical aspects of KPFM measurements on semiconductors required for the correct interpretation of the detected KPFM bias are discussed. A new KPFM model is developed which enables the quantitative correlation between the probed KPFM bias and the dopant concentration in the investigated semiconducting sample. Quantitative dopant profiling by means of the new KPFM model is demonstrated by the example of differently structured, n- and p-type doped silicon. Additionally, the transport of charge carriers during KPFM measurements, in particular in the presence of intrinsic electric fields due to vertical and horizontal pn junctions as well as due to surface space charge regions, is discussed. Detailed investigations show that transport of charge carriers in the semiconducting sample is a crucial aspect and has to be taken into account when aiming for a quantitative evaluation of the probed KPFM bias.

Aggregation in thin-film silver: Induced by chlorine and inhibited by alloying with two dopants

International Nuclear Information System (INIS)

Koike, Katsuhiko; Shimada, Koichi; Fukuda, Shin

2009-01-01

The Ag aggregation mechanism triggered by chlorine (Cl) is discussed. The frontier orbital theory by K. Fukui is applied in order to determine the growing point in the silver (Ag) cluster. Ag in the thin-film silver would grow to Ag n Cl and stack, triggered by Cl from the outside according to the mechanism described. This would lead to an aggregate with a high Ag density. It is suggested that this would be the generating mechanism of the silver-gray aggregate consisting mostly of Ag, which is generated by exposing it to Cl. Two tactics in order to prevent restrain aggregation induced by Cl according to the mechanism are proposed. Tactic 1 is a restraining of structure change to a plane in the process of Ag 6 Cl + Ag → Ag 7 Cl. Tactic 2 is the trapping of Cl before it generates a bond to Ag. The ability of the two combined dopants with the abilities of tactics 1 and 2, such as in an Ag alloy including palladium and copper (APC), and including neodymium and gold (ANA) is expected to be very high. The aggregation resistance of an Ag alloy including two dopants is evaluated by a salt water immersion test. The APC and ANA demonstrated a very high resistance to Cl, because of the combination of the dopants working with tactic 1 (Pd, Au) and tactic 2 (Cu, Nd). The multilayer sputter coating with an ANA layer demonstrated a very interesting profile where the light transmittance and the electrical sheet resistance are almost the same as the multilayer sputter coating with a pure Ag. The multilayer sputter coating with AIS also demonstrates a very interesting profile, where the light transmittance is higher than the multilayer sputter coating with a pure Ag.

Dopant-free twinning superlattice formation in InSb and InP nanowires

Energy Technology Data Exchange (ETDEWEB)

Yuan, Xiaoming [School of Physics and Electronics, Hunan Key Laboratory for Supermicrostructure and Ultrafast Process, Central South University, Changsha, Hunan (China); Department of Electronic Materials Engineering, Research School of Physics and Engineering, The Australian National University, Canberra, ACT (Australia); Guo, Yanan; Caroff, Philippe; Tan, Hark Hoe; Jagadish, Chennupati [Department of Electronic Materials Engineering, Research School of Physics and Engineering, The Australian National University, Canberra, ACT (Australia); He, Jun [School of Physics and Electronics, Hunan Key Laboratory for Supermicrostructure and Ultrafast Process, Central South University, Changsha, Hunan (China)

2017-11-15

Periodic arrangement of twin planes creates a controllable polytype that can affect both the electronic and optical properties of nanowires. The approach that is most used for inducing twinning superlattice (TSL) formation in III-V nanowires is introducing impurity dopants during growth. Here, we demonstrate that controlling the growth parameters is sufficient to produce regular twinning planes in Au-catalysed InSb and InP nanowires. Our results show that TSL formation in InSb nanowires only exists in a very narrow growth window. We suggest that growth conditions induce a high concentration of In (or Sb) in the Au droplet, which plays a similar role to that of surfactant impurities such as Zn, and increases the droplet wetting angle to yield a geometry that is favorable for TSL formation. The demonstration of TSL structure in InSb and InP nanowires by controlling the input of In (or Sb) further enhances fundamental understanding of TSL formation in III-V nanowires and allows us to tune the properties of these nanowires by crystal phase engineering. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Dopant-free twinning superlattice formation in InSb and InP nanowires

International Nuclear Information System (INIS)

Yuan, Xiaoming; Guo, Yanan; Caroff, Philippe; Tan, Hark Hoe; Jagadish, Chennupati; He, Jun

2017-01-01

Periodic arrangement of twin planes creates a controllable polytype that can affect both the electronic and optical properties of nanowires. The approach that is most used for inducing twinning superlattice (TSL) formation in III-V nanowires is introducing impurity dopants during growth. Here, we demonstrate that controlling the growth parameters is sufficient to produce regular twinning planes in Au-catalysed InSb and InP nanowires. Our results show that TSL formation in InSb nanowires only exists in a very narrow growth window. We suggest that growth conditions induce a high concentration of In (or Sb) in the Au droplet, which plays a similar role to that of surfactant impurities such as Zn, and increases the droplet wetting angle to yield a geometry that is favorable for TSL formation. The demonstration of TSL structure in InSb and InP nanowires by controlling the input of In (or Sb) further enhances fundamental understanding of TSL formation in III-V nanowires and allows us to tune the properties of these nanowires by crystal phase engineering. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

The influence of Zn-dopant on the precipitation of α-FeOOH in highly alkaline media

International Nuclear Information System (INIS)

Krehula, Stjepko; Music, Svetozar; Skoko, Zeljko; Popovic, Stanko

2006-01-01

The influence of Zn-dopant on the precipitation of α-FeOOH in highly alkaline media was monitored by X-ray diffraction (XRD), 57 Fe Moessbauer and Fourier transform infrared (FT-IR) spectroscopies and field emission scanning electron microscopy (FE SEM). Acicular and monodisperse α-FeOOH particles were precipitated at a very high pH by adding a tetramethylammonium hydroxide solution to an aqueous solution of FeCl 3 . The XRD analysis of the samples precipitated in the presence of Zn 2+ ions showed the formation of solid solutions of α-(Fe, Zn)OOH up to a concentration ratio r = [Zn]/([Zn] + [Fe]) = 0.0909. ZnFe 2 O 4 was additionally formed in the precipitate for r = 0.1111, whereas the three phases α-FeOOH, α-Fe 2 O 3 and ZnFe 2 O 4 were formed for r 0.1304. In the corresponding FT-IR spectra, the Fe-OH and Fe-O stretching bands were sensitive to the Zn 2+ substitution, whereas the Fe-OH bending bands of α-FeOOH at 892 and 796 cm -1 were almost insensitive. The Moessbauer spectra showed a high sensitivity to the formation of α-(Fe, Zn)OOH solid solutions which were monitored on the basis of a decrease in B hf values in dependence on Zn-doping. A strictly linear decrease in B hf for α-FeOOH doped with Zn 2+ ions was measured up to r = 0.0291, whereas for r = 0.0476 and higher there was a deviation from linearity. The presence of α-(Fe, Zn)OOH, α-Fe 2 O 3 and ZnFe 2 O 4 phases in the samples was determined quantitatively by Moessbauer spectroscopy. Likewise, Moessbauer spectroscopy did not show any formation of the solid solutions of α-Fe 2 O 3 with Zn 2+ ions. FE SEM showed a strong effect of Zn-doping on the elongation of acicular α-FeOOH particles (∼500-700 nm in length) up to r = 0.1111. For r = 0.1304 the sizes of ZnFe 2 O 4 particles were around 30-50 nm, and those of α-Fe 2 O 3 particles were around 500 nm, whereas a relatively small number of very elongated α-(Fe, Zn)OOH particles was observed. A possible mechanism of the formation of �

Study of the response reduction of LiF:Mg, Ti dosimeter for high dose dosimetry

Energy Technology Data Exchange (ETDEWEB)

Torkzadeh, Falamarz [Nuclear Sciences and Technology Research Institute, Tehran (Iran, Islamic Republic of). Radiation Applications Research School; AEOI, Tehran (Iran, Islamic Republic of); Faripour, Heidar [Nuclear Sciences and Technology Research Institute, Tehran (Iran, Islamic Republic of). Laser and Optics Research School; AEOI, Tehran (Iran, Islamic Republic of); Mardashti, Forough; Manouchehri, Farhad [Nuclear Sciences and Technology Research Institute, Tehran (Iran, Islamic Republic of). Radiation Applications Research School

2017-07-15

A single crystal and 5 polycrystalline samples of LiF:Mg, Ti and their pellets were prepared and investigated so as to apply thermoluminescence high gamma dose dosimetry. Three zones of single crystal with dopant concentrations of 200 ppm of Mg and 20 ppm of Ti were also used to prepare the single crystal samples. For polycrystalline samples, dopant concentrations of 0.062 mol% Mg and Ti concentrations in the range of 0.016 and 0.046 mol% were used. All the samples were exposed to gamma doses of 1 kGy to 700 kGy and their response changes were determined by a gamma dose test of about 60 mGy. According to the results obtained, the use of response reduction by curve-fitting up to about 300 kGy can be performed reliably for high dose gamma dosimetry.

A helical naphthopyran dopant for photoresponsive cholesteric liquid crystals

OpenAIRE

Kim, Yuna; Frigoli, Michel; Vanthuyne, Nicolas; Tamaoki, Nobuyuki

2017-01-01

The first photoresponsive cholesteric liquid crystal comprising a photoisomerizable helical naphthopyran derivative dopant and a nematic liquid crystal is reported. An unprecedented helical twisting power switching ratio of over 90% allowed us to demonstrate multi-cycle rotational motion of micro-objects by UV light irradiation.

Charge Exchange Reaction in Dopant-Assisted Atmospheric Pressure Chemical Ionization and Atmospheric Pressure Photoionization.

Science.gov (United States)

Vaikkinen, Anu; Kauppila, Tiina J; Kostiainen, Risto

2016-08-01

The efficiencies of charge exchange reaction in dopant-assisted atmospheric pressure chemical ionization (DA-APCI) and dopant-assisted atmospheric pressure photoionization (DA-APPI) mass spectrometry (MS) were compared by flow injection analysis. Fourteen individual compounds and a commercial mixture of 16 polycyclic aromatic hydrocarbons were chosen as model analytes to cover a wide range of polarities, gas-phase ionization energies, and proton affinities. Chlorobenzene was used as the dopant, and methanol/water (80/20) as the solvent. In both techniques, analytes formed the same ions (radical cations, protonated molecules, and/or fragments). However, in DA-APCI, the relative efficiency of charge exchange versus proton transfer was lower than in DA-APPI. This is suggested to be because in DA-APCI both dopant and solvent clusters can be ionized, and the formed reagent ions can react with the analytes via competing charge exchange and proton transfer reactions. In DA-APPI, on the other hand, the main reagents are dopant-derived radical cations, which favor ionization of analytes via charge exchange. The efficiency of charge exchange in both DA-APPI and DA-APCI was shown to depend heavily on the solvent flow rate, with best efficiency seen at lowest flow rates studied (0.05 and 0.1 mL/min). Both DA-APCI and DA-APPI showed the radical cation of chlorobenzene at 0.05-0.1 mL/min flow rate, but at increasing flow rate, the abundance of chlorobenzene M(+.) decreased and reagent ion populations deriving from different gas-phase chemistry were recorded. The formation of these reagent ions explains the decreasing ionization efficiency and the differences in charge exchange between the techniques. Graphical Abstract ᅟ.

Effect of Mg{sup 2+} and Ti{sup 4+} dopants on the structural, magnetic and high-frequency ferromagnetic properties of barium hexaferrite

Energy Technology Data Exchange (ETDEWEB)

Shams, Mohammad H. [Department of Physics, University of Isfahan, Hezar Jarib Street, Isfahan 81746-73441 (Iran, Islamic Republic of); Rozatian, Amir S.H., E-mail: a.s.h.rozatian@phys.ui.ac.ir [Department of Physics, University of Isfahan, Hezar Jarib Street, Isfahan 81746-73441 (Iran, Islamic Republic of); Yousefi, Mohammad H. [Department of Physics, University of Isfahan, Hezar Jarib Street, Isfahan 81746-73441 (Iran, Islamic Republic of); Valíček, Jan [Institute of Physics, Faculty of Mining and Geology, VŠB – Technical University of Ostrava, 17. Listopadu 15, 70833 Ostrava-Poruba (Czech Republic); Šepelák, Vladimir [Institute of Nanotechnology, Karlsruhe Institute of Technology, 76344 Eggenstein-Leopoldshafen (Germany); Slovak Academy of Sciences, Watsonova 45, 04001 Košice (Slovakia)

2016-02-01

The doped barium hexaferrite, BaFe{sub 12−x}(Mg{sub 0.5}Ti{sub 0.5}){sub x}O{sub 19} with 1≤x≤5, is synthesized by a solid state ceramic method. Its crystalline structure, morphology, as well as static and dynamic magnetic properties are investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), vibrating sample magnetometry, and vector network analysis, respectively. The cation distribution of Mg{sup 2+} and Ti{sup 4+} in the hexagonal structure of BaFe{sub 12−x}(Mg{sub 0.5}Ti{sub 0.5}){sub x}O{sub 19} is investigated by {sup 57}Fe Mössbauer spectroscopy. The effect of Mg{sup 2+} and Ti{sup 4+} dopants on static and high-frequency magnetic properties of the ferrite is studied. - Highlights: • The BaFe{sub 12−x}(MgTi){sub 0.5x}O{sub 19} (x =1– 5) are synthesized by a solid state reaction method. • The Mg{sup 2+} and Ti{sup 4+} dopants take positions 12k for x=1 and 4f{sub 1} and 4f{sub 2} for x=5. • The coercivity and magnetization are decreased with an increase in Mg–Ti content. • The ferromagnetic resonance frequency is decreased with increase of x. • The FMR is shifted to lower frequencies due to the reduction of the anisotropy field.

Influence of temperature and dopant concentration on structural, morphological and optical properties of nanometric Ce1-xErxO2-δ (x = 0.05–0.20) as a pigment

KAUST Repository

Stojmenović, Marija

2015-07-31

Ceramic pigments based on cerium oxide were synthesized by self–propagating room temperature method and their color properties were assessed from the viewpoint of potential environmentally nontoxic pink pigments. Thermal stabilities of the pigments were examined at 600, 900 and 1200 ºC. According to X–ray powder diffraction and Raman spectroscopy results, all obtained pigments were single–phase solid solutions of cerium oxide, independent of the concentration of dopants. The X–ray analysis showed that the crystallites were of nanometric dimensions, as recorded and by transmission electron microscopy analysis. Color characteristics of solid solutions, which depended on concentracion erbium ions and calcination temperature, and their position in the chromaticity diagram were studied by ultraviolet–visible spectrophotometry, which confirmed potential application of environmentally friendly pigments of desired color. The color efficiency of pigments was also evaluated by colorimetric analysis.

Influence of temperature and dopant concentration on structural, morphological and optical properties of nanometric Ce1-xErxO2-δ (x = 0.05–0.20) as a pigment

KAUST Repository

Stojmenović, Marija; Milenković, Maja C.; Banković, Predrag T.; Zunic, Milan; Gulicovski, Jelena J.; Pantić, Jelena R.; Bošković, Snežana B.

2015-01-01

Ceramic pigments based on cerium oxide were synthesized by self–propagating room temperature method and their color properties were assessed from the viewpoint of potential environmentally nontoxic pink pigments. Thermal stabilities of the pigments were examined at 600, 900 and 1200 ºC. According to X–ray powder diffraction and Raman spectroscopy results, all obtained pigments were single–phase solid solutions of cerium oxide, independent of the concentration of dopants. The X–ray analysis showed that the crystallites were of nanometric dimensions, as recorded and by transmission electron microscopy analysis. Color characteristics of solid solutions, which depended on concentracion erbium ions and calcination temperature, and their position in the chromaticity diagram were studied by ultraviolet–visible spectrophotometry, which confirmed potential application of environmentally friendly pigments of desired color. The color efficiency of pigments was also evaluated by colorimetric analysis.

N-Type delta Doping of High-Purity Silicon Imaging Arrays

Science.gov (United States)

Blacksberg, Jordana; Hoenk, Michael; Nikzad, Shouleh

2005-01-01

A process for n-type (electron-donor) delta doping has shown promise as a means of modifying back-illuminated image detectors made from n-doped high-purity silicon to enable them to detect high-energy photons (ultraviolet and x-rays) and low-energy charged particles (electrons and ions). This process is applicable to imaging detectors of several types, including charge-coupled devices, hybrid devices, and complementary metal oxide/semiconductor detector arrays. Delta doping is so named because its density-vs.-depth characteristic is reminiscent of the Dirac delta function (impulse function): the dopant is highly concentrated in a very thin layer. Preferably, the dopant is concentrated in one or at most two atomic layers in a crystal plane and, therefore, delta doping is also known as atomic-plane doping. The use of doping to enable detection of high-energy photons and low-energy particles was reported in several prior NASA Tech Briefs articles. As described in more detail in those articles, the main benefit afforded by delta doping of a back-illuminated silicon detector is to eliminate a "dead" layer at the back surface of the silicon wherein high-energy photons and low-energy particles are absorbed without detection. An additional benefit is that the delta-doped layer can serve as a back-side electrical contact. Delta doping of p-type silicon detectors is well established. The development of the present process addresses concerns specific to the delta doping of high-purity silicon detectors, which are typically n-type. The present process involves relatively low temperatures, is fully compatible with other processes used to fabricate the detectors, and does not entail interruption of those processes. Indeed, this process can be the last stage in the fabrication of an imaging detector that has, in all other respects, already been fully processed, including metallized. This process includes molecular-beam epitaxy (MBE) for deposition of three layers, including

Technical report Development of a piezoelectric inkjet dopant delivery device for an atmospheric pressure photoionization source with liquid chromatography/mass spectrometry

KAUST Repository

Amad, Maan H.

2013-01-01

This paper describes a simple robust and integrated piezoelectric actuated printhead as a dopant delivery system for atmospheric pressure photoionization with liquid chromatography/mass spectrometry The newly designed dopant delivery system avoids problems associated with traditional liquid delivery systems such as solvent immiscibility backpressure and increased post-column dead volume issues The performance of the new device was tested and evaluated using chlorobenzene as a dopant with a test mixture consisting of 18 different polycyclic aromatic hydrocarbons (PAHs) The results show that the new system works robustly at low dopant consumption level (16 uL min-1) consuming only approximately 5% of the amount used by conventional sources The low dopant consumption has resulted in up to a 20-fold reduction in signal intensity of tested PAH molecules but has led to less presence of background cluster ions and dopant trace contaminant background ions in the source area Consequently all tested PAHs were detected with excellent signal-to-noise ratio with at least two-to ten-fold improvements in the limit of detection and quantification compared to those obtained with traditional dopant assistance using a post-column addition method © IM Publications LLP 2013.

Application of real space Kerker method in simulating gate-all-around nanowire transistors with realistic discrete dopants*

International Nuclear Information System (INIS)

Li Chang-Sheng; Ma Lei; Guo Jie-Rong

2017-01-01

We adopt a self-consistent real space Kerker method to prevent the divergence from charge sloshing in the simulating transistors with realistic discrete dopants in the source and drain regions. The method achieves efficient convergence by avoiding unrealistic long range charge sloshing but keeping effects from short range charge sloshing. Numerical results show that discrete dopants in the source and drain regions could have a bigger influence on the electrical variability than the usual continuous doping without considering charge sloshing. Few discrete dopants and the narrow geometry create a situation with short range Coulomb screening and oscillations of charge density in real space. The dopants induced quasi-localized defect modes in the source region experience short range oscillations in order to reach the drain end of the device. The charging of the defect modes and the oscillations of the charge density are identified by the simulation of the electron density. (paper)

n-type dopants in (001) β-Ga2O3 grown on (001) β-Ga2O3 substrates by plasma-assisted molecular beam epitaxy

Science.gov (United States)

Han, Sang-Heon; Mauze, Akhil; Ahmadi, Elaheh; Mates, Tom; Oshima, Yuichi; Speck, James S.

2018-04-01

Ge and Sn as n-type dopants in (001) β-Ga2O3 films were investigated using plasma-assisted molecular beam epitaxy. The Ge concentration showed a strong dependence on the growth temperature, whereas the Sn concentration remains independent of the growth temperature. The maximum growth temperature at which a wide range of Ge concentrations (from 1017 to 1020 cm-3) could be achieved was 675 °C while the same range of Sn concentration could be achieved at growth temperature of 750 °C. Atomic force microscopy results revealed that higher growth temperature shows better surface morphology. Therefore, our study reveals a tradeoff between higher Ge doping concentration and high quality surface morphology on (001) β-Ga2O3 films grown by plasma-assisted molecular beam epitaxy. The Ge doped films had an electron mobility of 26.3 cm2 V-1 s-1 at the electron concentration of 6.7 × 1017 cm-3 whereas the Sn doped films had an electron mobility of 25.3 cm2 V-1 s-1 at the electron concentration of 1.1 × 1018 cm-3.

Modulation of the acidity of niobic acid by ion-doping: Effects of nature and amount of the dopant ions

Energy Technology Data Exchange (ETDEWEB)

Carniti, Paolo [Dipartimento di Chimica, Università degli Studi di Milano (UNIMI), Milano (Italy); Gervasini, Antonella, E-mail: antonella.gervasini@unimi.it [Dipartimento di Chimica, Università degli Studi di Milano (UNIMI), Milano (Italy); Marzo, Matteo [Dipartimento di Chimica, Università degli Studi di Milano (UNIMI), Milano (Italy); Auroux, Aline [Université Lyon 1, CNRS, UMR 5256, (IRCELYON), Villeurbanne (France)

2013-09-10

Highlights: ► Mitigation of the surface acidity of niobic acid was pursued by K-, Ba-, and Nd-doping. ► Thermal techniques of study were effective for the acidity study. ► The nature of the dopant influences the effectiveness of the acidity tuning of niobic acid. ► The acidity of the doped surfaces decreased with increasing the dopant species added to niobic acid. ► The samples showed different acidity when measured in gas–solid phase (intrinsic acidity) and water (effective acidity). - Abstract: The acidity of niobic acid (NBO) has been successfully mitigated and tuned by addition of K{sup +}, Ba{sup 2+} and Nd{sup 3+} dopant species in amounts from 1 to 15 atom nm{sup −2}. The characterization of the intrinsic acid properties of the samples was performed by adsorption of NH{sub 3} in a volumetric–microcalorimetric coupled line and by temperature programmed desorption (TPD) of 2-phenylethylamine in a thermogravimetric apparatus. The K-dopant was more effective in decreasing the acidity of niobic acid than the Ba- and Nd-dopants. Complementary measurements of the effective acidity of the samples in water by base titrations with 2-phenylethylamine completed the study and revealed a different picture of the effect of the three dopants on the NBO acidity in water. All the results indicated that the K-dopant targeted more selectively the Brønsted acid sites, acting as an ion-exchanger, while Ba- and Nd-species predominantly acted on the Lewis acid sites of the NBO surface.

Phosphorus doped and defects engineered graphene for improved electrochemical sensing: synergistic effect of dopants and defects

International Nuclear Information System (INIS)

Chu, Ke; Wang, Fan; Tian, Ye; Wei, Zhen

2017-01-01

Heteroatom-doped graphene materials emerged as promising metal-free catalysts have recently attracted a growing interest in electrochemical sensing applications. However, their catalytic activity and sensing performances still need to be further improved. Herein, we reported the development of unique phosphorus (P)-doped and plasma-etched graphene (denoted as PG-E) as an efficient metal-free electrocatalyst for dopamine (DA) sensing. It was demonstrated that introducing both P-dopants and plasma-engineered defects in graphene could synergistically improve the activity toward electrocatalytic oxidation of DA by increasing the accessible active sites and promoting the electron transport capability. The resulting PG-E modified electrode showed exceptional DA sensing performances with low detection limit, high selectivity and good stability. These results suggested that the synergistic effect of dopants and defects might be an important factor for developing the advanced graphene-based metal-free catalysts for electrochemical sensing.

Location of rare-earth dopants on LiCAF and LiSAF laser hosts via XRD, EXAFS and computer modeling technique

International Nuclear Information System (INIS)

Valerio, Mario Ernesto Giroldo; Amaral, Jomar Batista de; Baldochi, Sonia Licia Vera; Mazzocchi, L.; Sasaki, Jose Marcos; Jackson, Robert A.

2004-01-01

Full text: Cr-doped LiCaAlF 6 (LiCAF) and LiSrAlF 6 (LiSAF) were used as laser operating in the near infrared region. Ce-doped LiCAF and LiSAF have been reported as leading candidates for tunable all-solid-state lasers in the UV region. Spectroscopic properties of LiCaAlF 6 : Nd suggest that this crystal can be used as selective optical filter and refractive element for 157 nm photolithography. The question of whether the RE dopant will prefer the Li + , the M 2+ site or the Al 3+ site is not yet known. Nevertheless most of the optical properties of these hosts including their laser action depend on the local symmetry, charge compensation mechanism and possible deformation of the lattice. In the present work, Powder X-ray Diffraction (XRD), X-ray Absorption Spectroscopy (XAS), Spectro fluorimetry, combined with computer modeling, were used to study the local structure around the dopant and determine the site occupied by them and also the distance and nature of the co-ordinating atoms. The compounds were prepared from commercially available CaF2 and SrF2 powders of high purity; LiF previously purified by the zone melting method, and AlF3 and RE dopants obtained from the hydro fluorination of commercial Al 2 O 3 . The synthesis of 2 mol % RE doped LiCAF and LiSAF samples were performed in a platinum reactor. The compositions were 2 mol % LiF and AlF3 enriched to compensate for their high vaporization. Powder XRD measurements were performed at room temperature in a Rigaku DMAX diffractometer in step scan mode using Cu K radiation. The Rietveld method (DBWS-9807a software) was employed in the analysis of the patterns. It was found that in the doped samples the concentration of the LiCAF or LiSAF phases are 84-95% and a small amount of AlF 3 and α - Li 3 AlF 6 were formed. The XAS experiments were performed on and above the L III absorption edge of the Er, Ho and Nd ions in fluorescence and transmission mode at room temperature in the XAS station at the LNLS, Campinas

Polycrystalline silicon carbide dopant profiles obtained through a scanning nano-Schottky contact

International Nuclear Information System (INIS)

Golt, M. C.; Strawhecker, K. E.; Bratcher, M. S.; Shanholtz, E. R.

2016-01-01

The unique thermo-electro-mechanical properties of polycrystalline silicon carbide (poly-SiC) make it a desirable candidate for structural and electronic materials for operation in extreme environments. Necessitated by the need to understand how processing additives influence poly-SiC structure and electrical properties, the distribution of lattice defects and impurities across a specimen of hot-pressed 6H poly-SiC processed with p-type additives was visualized with high spatial resolution using a conductive atomic force microscopy approach in which a contact forming a nano-Schottky interface is scanned across the sample. The results reveal very intricate structures within poly-SiC, with each grain having a complex core-rim structure. This complexity results from the influence the additives have on the evolution of the microstructure during processing. It was found that the highest conductivities localized at rims as well as at the interface between the rim and the core. The conductivity of the cores is less than the conductivity of the rims due to a lower concentration of dopant. Analysis of the observed conductivities and current-voltage curves is presented in the context of nano-Schottky contact regimes where the conventional understanding of charge transport to diode operation is no longer valid.

Polycrystalline silicon carbide dopant profiles obtained through a scanning nano-Schottky contact

Energy Technology Data Exchange (ETDEWEB)

Golt, M. C.; Strawhecker, K. E.; Bratcher, M. S. [U.S. Army Research Laboratory, WMRD, Aberdeen Proving Ground, Maryland 21005 (United States); Shanholtz, E. R. [ORISE, Belcamp, Maryland 21017 (United States)

2016-07-14

The unique thermo-electro-mechanical properties of polycrystalline silicon carbide (poly-SiC) make it a desirable candidate for structural and electronic materials for operation in extreme environments. Necessitated by the need to understand how processing additives influence poly-SiC structure and electrical properties, the distribution of lattice defects and impurities across a specimen of hot-pressed 6H poly-SiC processed with p-type additives was visualized with high spatial resolution using a conductive atomic force microscopy approach in which a contact forming a nano-Schottky interface is scanned across the sample. The results reveal very intricate structures within poly-SiC, with each grain having a complex core-rim structure. This complexity results from the influence the additives have on the evolution of the microstructure during processing. It was found that the highest conductivities localized at rims as well as at the interface between the rim and the core. The conductivity of the cores is less than the conductivity of the rims due to a lower concentration of dopant. Analysis of the observed conductivities and current-voltage curves is presented in the context of nano-Schottky contact regimes where the conventional understanding of charge transport to diode operation is no longer valid.

Effect of substrate type, dopant and thermal treatment on ...

Indian Academy of Sciences (India)

Effect of substrate type, dopant and thermal treatment on physicochemical properties of TiO2–SnO2 sol–gel films. I STAMBOLOVA. ∗. , V BLASKOV, S VASSILEV†, M SHIPOCHKA and A LOUKANOV‡. Institute of General and Inorganic Chemistry, †Institute of Electrochemistry and Energy Systems, BAS,. Acad. G. Bonchev ...

Solvent effects on dopant-free pH-falling polymerization of aniline

Czech Academy of Sciences Publication Activity Database

Rakić, A. A.; Vukomanović, M.; Trifunovic, S.; Travas-Sejdic, J.; Chaudhary, O. J.; Horský, Jiří; Ciric-Marjanovic, G.

2015-01-01

Roč. 209, November (2015), s. 279-296 ISSN 0379-6779 Institutional support: RVO:61389013 Keywords : dopant-free template -free method * nanostructures * polyaniline Subject RIV: CD - Macromolecular Chemistry Impact factor: 2.299, year: 2015

High concentration agglomerate dynamics at high temperatures.

Science.gov (United States)

Heine, M C; Pratsinis, S E

2006-11-21

The dynamics of agglomerate aerosols are investigated at high solids concentrations that are typical in industrial scale manufacture of fine particles (precursor mole fraction larger than 10 mol %). In particular, formation and growth of fumed silica at such concentrations by chemical reaction, coagulation, and sintering is simulated at nonisothermal conditions and compared to limited experimental data and commercial product specifications. Using recent chemical kinetics for silica formation by SiCl4 hydrolysis and neglecting aerosol polydispersity, the evolution of the diameter of primary particles (specific surface area, SSA), hard- and soft-agglomerates, along with agglomerate effective volume fraction (volume occupied by agglomerate) is investigated. Classic Smoluchowski theory is fundamentally limited for description of soft-agglomerate Brownian coagulation at high solids concentrations. In fact, these high concentrations affect little the primary particle diameter (or SSA) but dominate the soft-agglomerate diameter, structure, and volume fraction, leading to gelation consistent with experimental data. This indicates that restructuring and fragmentation should affect product particle characteristics during high-temperature synthesis of nanostructured particles at high concentrations in aerosol flow reactors.

High-concentration boron doping of graphene nanoplatelets by simple thermal annealing and their supercapacitive properties.

Science.gov (United States)

Yeom, Da-Young; Jeon, Woojin; Tu, Nguyen Dien Kha; Yeo, So Young; Lee, Sang-Soo; Sung, Bong June; Chang, Hyejung; Lim, Jung Ah; Kim, Heesuk

2015-05-05

For the utilization of graphene in various energy storage and conversion applications, it must be synthesized in bulk with reliable and controllable electrical properties. Although nitrogen-doped graphene shows a high doping efficiency, its electrical properties can be easily affected by oxygen and water impurities from the environment. We here report that boron-doped graphene nanoplatelets with desirable electrical properties can be prepared by the simultaneous reduction and boron-doping of graphene oxide (GO) at a high annealing temperature. B-doped graphene nanoplatelets prepared at 1000 °C show a maximum boron concentration of 6.04 ± 1.44 at %, which is the highest value among B-doped graphenes prepared using various methods. With well-mixed GO and g-B2O3 as the dopant, highly uniform doping is achieved for potentially gram-scale production. In addition, as a proof-of-concept, highly B-doped graphene nanoplatelets were used as an electrode of an electrochemical double-layer capacitor (EDLC) and showed an excellent specific capacitance value of 448 F/g in an aqueous electrolyte without additional conductive additives. We believe that B-doped graphene nanoplatelets can also be used in other applications such as electrocatalyst and nano-electronics because of their reliable and controllable electrical properties regardless of the outer environment.

High-concentration boron doping of graphene nanoplatelets by simple thermal annealing and their supercapacitive properties

Science.gov (United States)

Yeom, Da-Young; Jeon, Woojin; Tu, Nguyen Dien Kha; Yeo, So Young; Lee, Sang-Soo; Sung, Bong June; Chang, Hyejung; Lim, Jung Ah; Kim, Heesuk

2015-05-01

For the utilization of graphene in various energy storage and conversion applications, it must be synthesized in bulk with reliable and controllable electrical properties. Although nitrogen-doped graphene shows a high doping efficiency, its electrical properties can be easily affected by oxygen and water impurities from the environment. We here report that boron-doped graphene nanoplatelets with desirable electrical properties can be prepared by the simultaneous reduction and boron-doping of graphene oxide (GO) at a high annealing temperature. B-doped graphene nanoplatelets prepared at 1000 °C show a maximum boron concentration of 6.04 ± 1.44 at %, which is the highest value among B-doped graphenes prepared using various methods. With well-mixed GO and g-B2O3 as the dopant, highly uniform doping is achieved for potentially gram-scale production. In addition, as a proof-of-concept, highly B-doped graphene nanoplatelets were used as an electrode of an electrochemical double-layer capacitor (EDLC) and showed an excellent specific capacitance value of 448 F/g in an aqueous electrolyte without additional conductive additives. We believe that B-doped graphene nanoplatelets can also be used in other applications such as electrocatalyst and nano-electronics because of their reliable and controllable electrical properties regardless of the outer environment.

Low-cost copper complexes as p-dopants in solution processable hole transport layers

Energy Technology Data Exchange (ETDEWEB)

Kellermann, Renate [Department for Materials Science and Engineering, Chair for Materials for Electronics and Energy Technology, Friedrich-Alexander-University Erlangen-Nuremberg, Erlangen 91058 (Germany); Siemens AG – Corporate Technology, Guenther-Scharowsky-Str. 1, Erlangen 91058 (Germany); Taroata, Dan; Maltenberger, Anna; Hartmann, David; Schmid, Guenter [Siemens AG – Corporate Technology, Guenther-Scharowsky-Str. 1, Erlangen 91058 (Germany); Brabec, Christoph J. [Department for Materials Science and Engineering, Chair for Materials for Electronics and Energy Technology, Friedrich-Alexander-University Erlangen-Nuremberg, Erlangen 91058 (Germany)

2015-09-07

We demonstrate the usage of the Lewis-acidic copper(II)hexafluoroacetylacetonate (Cu(hfac){sub 2}) and copper(II)trifluoroacetylacetonate (Cu(tfac){sub 2}) as low-cost p-dopants for conductivity enhancement of solution processable hole transport layers based on small molecules in organic light emitting diodes (OLEDs). The materials were clearly soluble in mixtures of environmentally friendly anisole and xylene and spin-coated under ambient atmosphere. Enhancements of two and four orders of magnitude, reaching 4.0 × 10{sup −11} S/cm with a dopant concentration of only 2 mol% Cu(hfac){sub 2} and 1.5 × 10{sup −9} S/cm with 5 mol% Cu(tfac){sub 2} in 2,2′,7,7′-tetra(N,N-ditolyl)amino-9,9-spiro-bifluorene (spiro-TTB), respectively, were achieved. Red light emitting diodes were fabricated with reduced driving voltages and enhanced current and power efficiencies (8.6 lm/W with Cu(hfac){sub 2} and 5.6 lm/W with Cu(tfac){sub 2}) compared to the OLED with undoped spiro-TTB (3.9 lm/W). The OLED with Cu(hfac){sub 2} doped spiro-TTB showed an over 8 times improved LT{sub 50} lifetime of 70 h at a starting luminance of 5000 cd/m{sup 2}. The LT{sub 50} lifetime of the reference OLED with PEDOT:PSS was only 8 h. Both non-optimized OLEDs were operated at similar driving voltage and power efficiency.

Dopant induced single electron tunneling within the sub-bands of single silicon NW tri-gate junctionless n-MOSFET

Science.gov (United States)

Uddin, Wasi; Georgiev, Yordan M.; Maity, Sarmistha; Das, Samaresh

2017-09-01

We report 1D electron transport of silicon junctionless tri-gate n-type transistor at 4.2 K. The step like curve observed in the current voltage characteristic suggests 1D transport. Besides the current steps for 1D transport, we found multiple spikes within individual steps, which we relate to inter-band single electron tunneling, mediated by the charged dopants available in the channel region. Clear Coulomb diamonds were observed in the stability diagram of the device. It is shown that a uniformly doped silicon nanowire can provide us the window for the single electron tunnelling. Back-gate versus front-gate color plot, where current is in a color scale, shows a crossover of the increased conduction region. This is a clear indication of the dopant-dopant interaction. It has been shown that back-gate biasing can be used to tune the coupling strength between the dopants.

Tris(2-(1 H -pyrazol-1-yl)pyridine)cobalt(III) as p-Type Dopant for Organic Semiconductors and Its Application in Highly Efficient Solid-State Dye-Sensitized Solar Cells

KAUST Repository

Burschka, Julian

2011-11-16

Chemical doping is an important strategy to alter the charge-transport properties of both molecular and polymeric organic semiconductors that find widespread application in organic electronic devices. We report on the use of a new class of Co(III) complexes as p-type dopants for triarylamine-based hole conductors such as spiro-MeOTAD and their application in solid-state dye-sensitized solar cells (ssDSCs). We show that the proposed compounds fulfill the requirements for this application and that the discussed strategy is promising for tuning the conductivity of spiro-MeOTAD in ssDSCs, without having to rely on the commonly employed photo-doping. By using a recently developed high molar extinction coefficient organic D-π-A sensitizer and p-doped spiro-MeOTAD as hole conductor, we achieved a record power conversion efficiency of 7.2%, measured under standard solar conditions (AM1.5G, 100 mW cm -2). We expect these promising new dopants to find widespread applications in organic electronics in general and photovoltaics in particular. © 2011 American Chemical Society.

Origin of electrolyte-dopant dependent sulfur poisoning of SOFC anodes

DEFF Research Database (Denmark)

Zeng, Zhenhua; Björketun, Mårten E; Ebbesen, Sune

2013-01-01

The mechanisms governing the sulfur poisoning of the triple phase boundary (TPB) of Ni-XSZ (X2O3 stabilized zirconia) anodes have been investigated using density functional theory. The calculated sulfur adsorption energies reveal a clear correlation between the size of the cation dopant X3...

On the roles of the dopants in LiF: Mg,Cu,Na,Si thermoluminescent material

International Nuclear Information System (INIS)

Lee, J. I.; Kim, J. L.; Chang, S. Y.; Chung, K. S.; Choe, H. S.

2005-01-01

In this paper, some results of the study on the roles of the dopants in the LiF:Mg,Cu,Na,Si thermoluminescent (TL) material that was developed at the Korea Atomic Energy Research Inst. for radiation protection are presented. Although there have been many studies to investigate the roles of the dopants in LiF:Mg,Cu,P TL material in the TL process, there are some discrepancies in the understanding of the roles of Cu and P between various researchers. In case of LiF:Mg,Cu,Na,Si TL material, there are a few studies on the roles of the dopants. Three kinds of samples in each of which one dopant is excluded, and the optimised sample, were prepared for this study. The measurements and analysis of the three-dimensional TL spectra, based on the temperature, wavelength and intensity, and the glow curves for those samples are used in this study. The results show that Mg plays a role in the trapping of the charge carriers and Cu plays a role in the luminescence recombination process; however, the effect of Na and Si on the glow curve structure and the TL emission spectra is much less than that of Mg and Cu. It is considered that Na and Si each plays a role in the improvement of the luminescence efficiency. (authors)

Efficient photoluminescence of Dy3+ at low concentrations in nanocrystalline ZrO2

International Nuclear Information System (INIS)

Diaz-Torres, L.A.; Rosa, E. de la; Salas, P.; Romero, V.H.; Angeles-Chavez, C.

2008-01-01

Nanocrystalline ZrO 2 :Dy 3+ were prepared by sol-gel and the structural and photoluminescence properties characterized. The crystallite size ranges from 20 to 50 nm and the crystalline phase is a mixture of tetragonal and monoclinic structure controlled by dopant concentration. Strong white light produced by the host emission band centered at ∼460 nm and two strong Dy 3+ emission bands, blue (488 nm) and yellow (580 nm), under direct excitation at 350 nm were observed. The highest efficiency was obtained for 0.5 mol% of Dy 3+ . Emission is explained in terms of high asymmetry of the host suggesting that Dy 3+ are substituted mainly into Zr 4+ lattice sites at the crystallite surface. Luminescence quenching is explained in terms of cross-relaxation of intermediate Dy 3+ levels. - Graphical abstract: White light emission from ∼70 nm ZrO 2 :Dy 3+ nanocrystals. The highest efficiency was obtained for 0.5 mol% of dopant and the dominant crystalline structure was monoclinic

Complex EUV imaging reflectometry: spatially resolved 3D composition determination and dopant profiling with a tabletop 13nm source

Science.gov (United States)

Porter, Christina L.; Tanksalvala, Michael; Gerrity, Michael; Miley, Galen P.; Esashi, Yuka; Horiguchi, Naoto; Zhang, Xiaoshi; Bevis, Charles S.; Karl, Robert; Johnsen, Peter; Adams, Daniel E.; Kapteyn, Henry C.; Murnane, Margaret M.

2018-03-01

With increasingly 3D devices becoming the norm, there is a growing need in the semiconductor industry and in materials science for high spatial resolution, non-destructive metrology techniques capable of determining depth-dependent composition information on devices. We present a solution to this problem using ptychographic coherent diffractive imaging (CDI) implemented using a commercially available, tabletop 13 nm source. We present the design, simulations, and preliminary results from our new complex EUV imaging reflectometer, which uses coherent 13 nm light produced by tabletop high harmonic generation. This tool is capable of determining spatially-resolved composition vs. depth profiles for samples by recording ptychographic images at multiple incidence angles. By harnessing phase measurements, we can locally and nondestructively determine quantities such as device and thin film layer thicknesses, surface roughness, interface quality, and dopant concentration profiles. Using this advanced imaging reflectometer, we can quantitatively characterize materials-sciencerelevant and industry-relevant nanostructures for a wide variety of applications, spanning from defect and overlay metrology to the development and optimization of nano-enhanced thermoelectric or spintronic devices.

Three dimensional mapping of Fe dopants in ceria nanocrystals using direct spectroscopic electron tomography

Energy Technology Data Exchange (ETDEWEB)

Goris, Bart; Meledina, Maria; Turner, Stuart [EMAT, University of Antwerp, Groenenborgerlaan 171, 2020 Antwerp (Belgium); Zhong, Zhichao [Centrum Wiskunde & Informatica, P.O. Box 94079, 1090 GB Amsterdam (Netherlands); Batenburg, K. Joost [Centrum Wiskunde & Informatica, P.O. Box 94079, 1090 GB Amsterdam (Netherlands); Mathematical Institute, Leiden University, Niels Bohrweg 1, 2333CA Leiden (Netherlands); Bals, Sara [EMAT, University of Antwerp, Groenenborgerlaan 171, 2020 Antwerp (Belgium)

2016-12-15

Electron tomography is a powerful technique for the 3D characterization of the morphology of nanostructures. Nevertheless, resolving the chemical composition of complex nanostructures in 3D remains challenging and the number of studies in which electron energy loss spectroscopy (EELS) is combined with tomography is limited. During the last decade, dedicated reconstruction algorithms have been developed for HAADF-STEM tomography using prior knowledge about the investigated sample. Here, we will use the prior knowledge that the experimental spectrum of each reconstructed voxel is a linear combination of a well-known set of references spectra in a so-called direct spectroscopic tomography technique. Based on a simulation experiment, it is shown that this technique provides superior results in comparison to conventional reconstruction methods for spectroscopic data, especially for spectrum images containing a relatively low signal to noise ratio. Next, this technique is used to investigate the spatial distribution of Fe dopants in Fe:Ceria nanoparticles in 3D. It is shown that the presence of the Fe{sup 2+} dopants is correlated with a reduction of the Ce atoms from Ce{sup 4+} towards Ce{sup 3+}. In addition, it is demonstrated that most of the Fe dopants are located near the voids inside the nanoparticle. - Highlights: • A direct tomographic reconstruction technique is proposed for spectroscopic data. • Spectrum fitting is combined with a tomography reconstruction in a single step. • The technique yields superior results for data with a low signal to noise ratio. • The technique is applied to map Fe dopants in ceria nanoparticles.

An insight into the dopant selection for CeO2-based resistive-switching memory system: a DFT and experimental study

Science.gov (United States)

Hussain, Fayyaz; Imran, Muhammad; Rana, Anwar Manzoor; Khalil, R. M. Arif; Khera, Ejaz Ahmad; Kiran, Saira; Javid, M. Arshad; Sattar, M. Atif; Ismail, Muhammad

2018-03-01

The aim of this study is to figure out better metal dopants for CeO2 for designing highly efficient non-volatile memory (NVM) devices. The present DFT work involves four different metals doped interstitially and substitutionally in CeO2 thin films. First principle calculations involve electron density of states (DOS) and partial density of states (PDOS), and isosurface charge densities are carried out within the plane-wave density functional theory using GGA and GGA + U approach by employing the Vienna ab initio simulation package VASP. Isosurface charge density plots confirmed that interstitial doping of Zr and Ti metals truly assists in generating conduction filaments (CFs), while substitutional doping of these metals cannot do so. Substitutional doping of W may contribute in generating CFs in CeO2 directly, but its interstitial doping improves conductivity of CeO2. However, Ni-dopant is capable of directly generating CFs both as substitutional and interstitial dopants in ceria. Such a capability of Ni appears acting as top electrode in Ni/CeO2/Pt memory devices, but its RS behavior is not so good. On inserting Zr layer to make Ni/Zr:CeO2/Pt memory stacks, Ni does not contribute in RS characteristics, but Zr plays a vital role in forming CFs by creating oxygen vacancies and forming ZrO2 interfacial layer. Therefore, Zr-doped devices exhibit high-resistance ratio of 104 and good endurance as compared to undoped devices suitable for RRAM applications.

A combined theoretical and experimental investigation about the influence of the dopant in the anodic electropolymerization of α-tetrathiophene

International Nuclear Information System (INIS)

Aleman, Carlos; Oliver, Ramon; Brillas, Enric; Casanovas, Jordi; Estrany, Francesc

2006-01-01

This work presents an experimental and theoretical investigation about the influence of the dopant in the electropolymerization of α-tetrathiophene. The results derived from anodic polymerization of α-tetrathiophene using SCN - , Cl - , Br - , NO 3 - ClO 3 - andClO 4 - as dopant agents are compared with theoretical results provided by quantum mechanical calculations on 1:1 charge-transfer complexes formed by α-tetrathiophene and X=SCN, Cl, Br, NO 3 , ClO 3 and ClO 4 . The consistency between experimental and theoretical results allows explain and rationalize the influence of the dopant in the electropolymerization of α-tetrathiophene

Damage accumulation and dopant migration during shallow As and Sb implantation into Si

Energy Technology Data Exchange (ETDEWEB)

Werner, M.; Berg, J.A. van den E-mail: j.a.vandenberg@salford.ac.uk; Armour, D.G.; Vandervorst, W.; Collart, E.H.J.; Goldberg, R.D.; Bailey, P.; Noakes, T.C.Q

2004-02-01

The damage evolution and concomitant dopant redistribution as a function of ion fluence during ultra shallow, heavy ion implants into Si have been investigated using medium energy ion scattering (MEIS) and secondary ion mass spectrometry (SIMS). These studies involved As and Sb ions implanted at room temperature, at energies of 2.5 and 2 keV to doses from 3 x 10{sup 13} to 5 x 10{sup 15} cm{sup -2}. MEIS is capable of detecting both the displaced atom and implant profiles with sub-nanometre depth resolution. These studies show that for doses up to 1 x 10{sup 14} cm{sup -2} (at which an amorphous layer is formed) the damage build up does not follow the energy deposition function. Instead it proceeds through the initial formation of a {approx}4 nm wide amorphous layer immediately under the oxide, that grows inwards into the bulk with increasing dose. This behaviour is explained in terms of the migration of some of the interstitials produced along the length of the collision cascade to the oxide or amorphous/crystal Si interface, where their trapping nucleates the growth of a shallow amorphous layer and the subsequent planar growth inwards of the damage layer. Although for doses {>=}4 x 10{sup 14} cm{sup -2} the As depth profiles agreed well with TRIM calculations, for lower doses As was observed to have a shallower profile, {approx}2 nm nearer to the surface. This behaviour is related the growth of the amorphous layer and ascribed to the movement of As into the near-surface amorphous layer (probably mediated by point defect migration) in which the larger dopant is accommodated more easily. SIMS studies have confirmed this dopant segregation effect. Shallow Sb implants also exhibit this novel dopant movement effect for low doses in combination with a damage evolution similar to As.

Damage accumulation and dopant migration during shallow As and Sb implantation into Si

International Nuclear Information System (INIS)

Werner, M.; Berg, J.A. van den; Armour, D.G.; Vandervorst, W.; Collart, E.H.J.; Goldberg, R.D.; Bailey, P.; Noakes, T.C.Q.

2004-01-01

The damage evolution and concomitant dopant redistribution as a function of ion fluence during ultra shallow, heavy ion implants into Si have been investigated using medium energy ion scattering (MEIS) and secondary ion mass spectrometry (SIMS). These studies involved As and Sb ions implanted at room temperature, at energies of 2.5 and 2 keV to doses from 3 x 10 13 to 5 x 10 15 cm -2 . MEIS is capable of detecting both the displaced atom and implant profiles with sub-nanometre depth resolution. These studies show that for doses up to 1 x 10 14 cm -2 (at which an amorphous layer is formed) the damage build up does not follow the energy deposition function. Instead it proceeds through the initial formation of a ∼4 nm wide amorphous layer immediately under the oxide, that grows inwards into the bulk with increasing dose. This behaviour is explained in terms of the migration of some of the interstitials produced along the length of the collision cascade to the oxide or amorphous/crystal Si interface, where their trapping nucleates the growth of a shallow amorphous layer and the subsequent planar growth inwards of the damage layer. Although for doses ≥4 x 10 14 cm -2 the As depth profiles agreed well with TRIM calculations, for lower doses As was observed to have a shallower profile, ∼2 nm nearer to the surface. This behaviour is related the growth of the amorphous layer and ascribed to the movement of As into the near-surface amorphous layer (probably mediated by point defect migration) in which the larger dopant is accommodated more easily. SIMS studies have confirmed this dopant segregation effect. Shallow Sb implants also exhibit this novel dopant movement effect for low doses in combination with a damage evolution similar to As

Lattice site location of electrical dopant impurities in group-III nitrides

CERN Document Server

Amorim, Lígia; Temst, Kristiaan; Wahl, Ulrich

Dopants are impurities introduced in semiconductors in small quantities to tailor the material characteristics, the effects of which depend on the exact site the dopant occupies in the crystal lattice. The lattice location of impurities is, thus, crucial for the overall understanding of the semiconductor characteristics. In general, several techniques can be used to investigate the lattice site of an impurity, the most accurate and dedicated being emission channeling. However, a characteristic of this technique is that it requires the implantation of radioactive probes, usually created and accelerated in a radioactive ion beam facility. In some cases, emission channeling might however be the only technique capable to investigate the lattice sites occupied by the impurity atoms, provided an appropriate isotope for this technique can be used. For instance, the use of other methods such as Rutherford backscattering spectrometry, perturbed angular correlations, Mössbauer spectroscopy and extended X-ray absorptio...

Ionization of EPA contaminants in direct and dopant-assisted atmospheric pressure photoionization and atmospheric pressure laser ionization.

Science.gov (United States)

Kauppila, Tiina J; Kersten, Hendrik; Benter, Thorsten

2015-06-01

Seventy-seven EPA priority environmental pollutants were analyzed using gas chromatography-mass spectrometry (GC-MS) equipped with an optimized atmospheric pressure photoionization (APPI) and an atmospheric pressure laser ionization (APLI) interface with and without dopants. The analyzed compounds included e.g., polycyclic aromatic hydrocarbons (PAHs), nitro compounds, halogenated compounds, aromatic compounds with phenolic, acidic, alcohol, and amino groups, phthalate and adipatic esters, and aliphatic ethers. Toluene, anisole, chlorobenzene, and acetone were tested as dopants. The widest range of analytes was ionized using direct APPI (66/77 compounds). The introduction of dopants decreased the amount of compounds ionized in APPI (e.g., 54/77 with toluene), but in many cases the ionization efficiency increased. While in direct APPI the formation of molecular ions via photoionization was the main ionization reaction, dopant-assisted (DA) APPI promoted ionization reactions, such as charge exchange and proton transfer. Direct APLI ionized a much smaller amount of compounds than APPI (41/77 compounds), showing selectivity towards compounds with low ionization energies (IEs) and long-lived resonantly excited intermediate states. DA-APLI, however, was able to ionize a higher amount of compounds (e.g. 51/77 with toluene), as the ionization took place entirely through dopant-assisted ion/molecule reactions similar to those in DA-APPI. Best ionization efficiency in APPI and APLI (both direct and DA) was obtained for PAHs and aromatics with O- and N-functionalities, whereas nitro compounds and aliphatic ethers were the most difficult to ionize. Halogenated aromatics and esters were (mainly) ionized in APPI, but not in APLI.

Crystal structure, chemical bond and enhanced performance of β-Zn4Sb3 compounds with interstitial indium dopant

International Nuclear Information System (INIS)

Tang, Dingguo; Zhao, Wenyu; Yu, Jian; Wei, Ping; Zhou, Hongyu; Zhu, Wanting; Zhang, Qingjie

2014-01-01

Highlights: • The interstitial In dopant leads to the local structural perturbations in β-Zn 4 Sb 3 . • The simultaneous increases in α and σ are observed in the In-doped Zn 4 Sb 3 compounds. • The In dopant plays different doping behaviors by the dopant contents in the samples. • A maximum ZT of 1.41 at 700 K is achieved for the In-doped Zn 4 Sb 3 compounds. - Abstract: In-doped β-Zn 4 Sb 3 compounds (Zn 4−x In x Sb 3 , 0 ⩽ x ⩽ 0.24) were prepared by melt-quenching and spark plasma sintering technology in the work. The resultant samples were systematically investigated by X-ray diffraction, X-ray photoelectron spectroscopy, differential scanning calorimetry and thermoelectric property measurements. The In dopant was identified to preferentially occupy the interstitial site in β-Zn 4 Sb 3 and led to the local structural perturbations near the 12c Sb2 and 36f Zn1 sites. The Auger parameters of Zn and Sb indicated that the increase in the valence of Zn was attributed to the charge transfer from Zn to In atoms. The binding energies of In 3d 5/2 core level showed that the interstitial In dopant was n-type dopant (In 3+ ) in slightly In-doped Zn 4−x In x Sb 3 , but acted as acceptor and was p-type dopant (In + ) in heavily In-doped ones. The discovery provides a reasonable explanation for the puzzled relation between σ and x for Zn 4−x In x Sb 3 . Simultaneously increasing the electrical conductivity and Seebeck coefficient of Zn 4−x In x Sb 3 can be realized through the local structural perturbations. The significantly enhanced power factor and the intrinsic low thermal conductivity resulted in a remarkable increase in the dimensionless figure of merit (ZT). The highest ZT reached 1.41 at 700 K for Zn 3.82 In 0.18 Sb 3 and increased by 68% compared with that of the undoped β-Zn 4 Sb 3

Heterovalent Dopant Incorporation for Bandgap and Type Engineering of Perovskite Crystals

KAUST Repository

Abdelhady, Ahmed L.

2016-01-02

Controllable doping of semiconductors is a fundamental technological requirement for electronic and optoelectronic devices. As intrinsic semiconductors, hybrid perovskites have so far been a phenomenal success in photovoltaics. The inability to dope these materials heterovalently (or aliovalently) has greatly limited their wider utilizations in electronics. Here we show an efficient in situ chemical route that achieves the controlled incorporation of trivalent cations (Bi3+, Au3+, or In3+) by exploiting the retrograde solubility behavior of perovskites. We term the new method dopant incorporation in the retrograde regime. We achieve Bi3+ incorporation that leads to bandgap tuning (∼300 meV), 104 fold enhancement in electrical conductivity, and a change in the sign of majority charge carriers from positive to negative. This work demonstrates the successful incorporation of dopants into perovskite crystals while preserving the host lattice structure, opening new avenues to tailor the electronic and optoelectronic properties of this rapidly emerging class of solution-processed semiconductors. © 2016 American Chemical Society.

Excitonic pathway to photoinduced magnetism in colloidal nanocrystals with nonmagnetic dopants.

Science.gov (United States)

Pinchetti, Valerio; Di, Qiumei; Lorenzon, Monica; Camellini, Andrea; Fasoli, Mauro; Zavelani-Rossi, Margherita; Meinardi, Francesco; Zhang, Jiatao; Crooker, Scott A; Brovelli, Sergio

2018-02-01

Electronic doping of colloidal semiconductor nanostructures holds promise for future device concepts in optoelectronic and spin-based technologies. Ag + is an emerging electronic dopant in III-V and II-VI nanostructures, introducing intragap electronic states optically coupled to the host conduction band. With its full 4d shell Ag + is nonmagnetic, and the dopant-related luminescence is ascribed to decay of the conduction-band electron following transfer of the photoexcited hole to Ag + . This optical activation process and the associated modification of the electronic configuration of Ag + remain unclear. Here, we trace a comprehensive picture of the excitonic process in Ag-doped CdSe nanocrystals and demonstrate that, in contrast to expectations, capture of the photohole leads to conversion of Ag + to paramagnetic Ag 2+ . The process of exciton recombination is thus inextricably tied to photoinduced magnetism. Accordingly, we observe strong optically activated magnetism and diluted magnetic semiconductor behaviour, demonstrating that optically switchable magnetic nanomaterials can be obtained by exploiting excitonic processes involving nonmagnetic impurities.

Heterovalent Dopant Incorporation for Bandgap and Type Engineering of Perovskite Crystals

KAUST Repository

Abdelhady, Ahmed L.; Saidaminov, Makhsud I.; Banavoth, Murali; Adinolfi, Valerio; Voznyy, Oleksandr; Katsiev, Khabiboulakh; Alarousu, Erkki; Comin, Riccardo; Dursun, Ibrahim; Sinatra, Lutfan; Sargent, Edward H.; Mohammed, Omar F.; Bakr, Osman

2016-01-01

Controllable doping of semiconductors is a fundamental technological requirement for electronic and optoelectronic devices. As intrinsic semiconductors, hybrid perovskites have so far been a phenomenal success in photovoltaics. The inability to dope these materials heterovalently (or aliovalently) has greatly limited their wider utilizations in electronics. Here we show an efficient in situ chemical route that achieves the controlled incorporation of trivalent cations (Bi3+, Au3+, or In3+) by exploiting the retrograde solubility behavior of perovskites. We term the new method dopant incorporation in the retrograde regime. We achieve Bi3+ incorporation that leads to bandgap tuning (∼300 meV), 104 fold enhancement in electrical conductivity, and a change in the sign of majority charge carriers from positive to negative. This work demonstrates the successful incorporation of dopants into perovskite crystals while preserving the host lattice structure, opening new avenues to tailor the electronic and optoelectronic properties of this rapidly emerging class of solution-processed semiconductors. © 2016 American Chemical Society.

Effect of La and W dopants on dielectric and ferroelectric properties of PZT thin films prepared by sol-gel process

International Nuclear Information System (INIS)

Xiao, Mi; Zhang, Zebin; Zhang, Weikang; Zhang, Ping

2018-01-01

La or W-doped lead zirconate titanate thin films (PLZT or PZTW) were prepared on platinized silicon substrates by sol-gel process. The effects of La or W dopant on the phase development, microstructure, dielectric and ferroelectric characteristics of films were studied. For PLZT films, the optimum doping concentration was found to be 2 mol%. While for PZTW films, the dielectric and ferroelectric properties were found to be improved as the doping concentration increased. The fatigue properties of PLZT and PZTW thin films were also investigated, the results showed that A- or B-site donor doping could improve the fatigue properties of PZT thin films. The theory of oxygen vacancy was used to explain the performance improvement caused by donor doping. (orig.)

Effect of La and W dopants on dielectric and ferroelectric properties of PZT thin films prepared by sol-gel process

Science.gov (United States)

Xiao, Mi; Zhang, Zebin; Zhang, Weikang; Zhang, Ping

2018-01-01

La or W-doped lead zirconate titanate thin films (PLZT or PZTW) were prepared on platinized silicon substrates by sol-gel process. The effects of La or W dopant on the phase development, microstructure, dielectric and ferroelectric characteristics of films were studied. For PLZT films, the optimum doping concentration was found to be 2 mol%. While for PZTW films, the dielectric and ferroelectric properties were found to be improved as the doping concentration increased. The fatigue properties of PLZT and PZTW thin films were also investigated, the results showed that A- or B-site donor doping could improve the fatigue properties of PZT thin films. The theory of oxygen vacancy was used to explain the performance improvement caused by donor doping.

The effect of dopant-induced electron traps on spectrum evolution of doped organic light-emitting devices

Energy Technology Data Exchange (ETDEWEB)

Zhan, Y.Q. [Surface Physics Laboratory (National Key Laboratory), Lab of Advanced Materials, Fudan University, Shanghai 200433 (China)]. E-mail: yqzhan@fudan.edu.cn; Zhou, J. [Surface Physics Laboratory (National Key Laboratory), Lab of Advanced Materials, Fudan University, Shanghai 200433 (China); Zhou, Y.C. [Surface Physics Laboratory (National Key Laboratory), Lab of Advanced Materials, Fudan University, Shanghai 200433 (China); Wu, Y. [Surface Physics Laboratory (National Key Laboratory), Lab of Advanced Materials, Fudan University, Shanghai 200433 (China); Yang, H. [Surface Physics Laboratory (National Key Laboratory), Lab of Advanced Materials, Fudan University, Shanghai 200433 (China); Li, F.Y. [Surface Physics Laboratory (National Key Laboratory), Lab of Advanced Materials, Fudan University, Shanghai 200433 (China); Ding, X.M. [Surface Physics Laboratory (National Key Laboratory), Lab of Advanced Materials, Fudan University, Shanghai 200433 (China); Hou, X.Y. [Surface Physics Laboratory (National Key Laboratory), Lab of Advanced Materials, Fudan University, Shanghai 200433 (China)]. E-mail: xyhou@fudan.edu.cn

2007-05-07

A prototype of light emitting device with two symmetrically located Al/LiF electrodes is fabricated to study the voltage dependence of emission spectra. 4-(dicyanomethylene)-2-methyl-6- (pdimethylaminostyryl)-4H-pyran doped tris-(8-hydroxy-quinolinato) aluminum thin film is the emitting layer of the device. Experiments show that with increasing applied voltage the emission intensity of the device decreases, of which the dopant emission intensity decreases more steeply than that of the host. Based on the theory of space-charge-limited current in insulator with a single shallow trap level it is deduced that the photoluminescence intensity of the dopant emission decreases linearly with applied voltage, in good agreement with experimental measurements. The evolution of the emission spectra can be well explained by the suggested mechanism that the electrons are trapped in the dopant molecules, which blocks the energy transfer from the host, and leads to more excitons in the host to emit light.

The effect of dopant-induced electron traps on spectrum evolution of doped organic light-emitting devices

International Nuclear Information System (INIS)

Zhan, Y.Q.; Zhou, J.; Zhou, Y.C.; Wu, Y.; Yang, H.; Li, F.Y.; Ding, X.M.; Hou, X.Y.

2007-01-01

A prototype of light emitting device with two symmetrically located Al/LiF electrodes is fabricated to study the voltage dependence of emission spectra. 4-(dicyanomethylene)-2-methyl-6- (pdimethylaminostyryl)-4H-pyran doped tris-(8-hydroxy-quinolinato) aluminum thin film is the emitting layer of the device. Experiments show that with increasing applied voltage the emission intensity of the device decreases, of which the dopant emission intensity decreases more steeply than that of the host. Based on the theory of space-charge-limited current in insulator with a single shallow trap level it is deduced that the photoluminescence intensity of the dopant emission decreases linearly with applied voltage, in good agreement with experimental measurements. The evolution of the emission spectra can be well explained by the suggested mechanism that the electrons are trapped in the dopant molecules, which blocks the energy transfer from the host, and leads to more excitons in the host to emit light

Amino Acid Functionalization of Doped Single-Walled Carbon Nanotubes: Effects of Dopants and Side Chains as Well as Zwitterionic Stabilizations.

Science.gov (United States)

Jiang, Lisha; Zhu, Chang; Fu, Yujie; Yang, Gang

2017-04-06

Functionalization of single-walled carbon nanotubes (SWCNTs) is necessitated in a number of conditions such as drug delivery, and here amino acid functionalization of SWCNTs is conducted within the framework of density functional theory. Functionalization efficiencies of Gly are largely determined by dopants, as a combined effect of atomic radius, electronic configuration, and distortion to SWCNTs. Different functionalization sites in Gly have divergent interaction strengths with M/SWCNTs that decline as O b > N > O a , and this trend seems almost independent of the identity of metallic dopants. B/SWCNT behaves distinctly and prefers to the N site. Dopants affect principally interaction strengths, while amino acids regulate significantly both functionalization configurations and interaction energies. Then focus is given to stabilization of zwitterionic amino acids due to enhanced interactions with the widely used zwitterionic drugs. All metallic dopants render zwitterionic Gly to be the most stable, and side chains in amino acids rather than dopants in M/SWCNTs cause more pronounced effects to zwitterionic stabilizations. Charge transfers between amino acids and M/SWCNTs are closely associated with zwitterionic stabilization effects, and different charge transfer mechanisms between M/SWCNTs and metal ions are interpreted. Thus, this work provides a comprehensive understanding of amino acid functionalization of M/SWCNTs.

A combined theoretical and experimental investigation about the influence of the dopant in the anodic electropolymerization of {alpha}-tetrathiophene

Energy Technology Data Exchange (ETDEWEB)

Aleman, Carlos [Departament d' Enginyeria Quimica, E.T.S. d' Enginyeria Industrial de Barcelona, Universitat Politecnica de Catalunya, Diagonal 647, Barcelona E-08028 (Spain)], E-mail: carlos.aleman@upc.edu; Oliver, Ramon [Unitat de Quimica Industrial, E.U.E. Tecnica Industrial de Barcelona, Universitat Politecnica de Catalunya, Comte d' Urgell 187, Barcelona E-08036 (Spain); Brillas, Enric [Departament de Quimica Fisica, Facultat de Quimica, Universitat de Barcelona, Marti i Franques 1, Barcelona E-08028 (Spain); Casanovas, Jordi [Departament de Quimica, Escola Politecnica Superior, Universitat de Lleida, c/Jaume II No. 69, Lleida E-25001 (Spain); Estrany, Francesc [Unitat de Quimica Industrial, E.U.E. Tecnica Industrial de Barcelona, Universitat Politecnica de Catalunya, Comte d' Urgell 187, Barcelona E-08036 (Spain)], E-mail: francesc.estrany@upc.edu

2006-04-21

This work presents an experimental and theoretical investigation about the influence of the dopant in the electropolymerization of {alpha}-tetrathiophene. The results derived from anodic polymerization of {alpha}-tetrathiophene using SCN{sup -}, Cl{sup -}, Br{sup -}, NO{sub 3}{sup -}ClO{sub 3}{sup -}andClO{sub 4}{sup -} as dopant agents are compared with theoretical results provided by quantum mechanical calculations on 1:1 charge-transfer complexes formed by {alpha}-tetrathiophene and X=SCN, Cl, Br, NO{sub 3}, ClO{sub 3} and ClO{sub 4}. The consistency between experimental and theoretical results allows explain and rationalize the influence of the dopant in the electropolymerization of {alpha}-tetrathiophene.

Direct imaging of dopant distribution in polycrystalline ZnO films

Czech Academy of Sciences Publication Activity Database

Lorenzo, F.; Aebersold, A.B.; Morales-Masis, M.; Ledinský, Martin; Escrig, S.; Vetushka, Aliaksi; Alexander, D.T.L.; Hessler-Wyser, A.; Fejfar, Antonín; Hébert, C.; Nicolay, S.; Ballif, C.

2017-01-01

Roč. 9, č. 8 (2017), s. 7241-7248 ISSN 1944-8244 R&D Projects: GA ČR GC16-10429J Institutional support: RVO:68378271 Keywords : dopant distribution * film polarity * grain boundaries * NanoSIMS * polycrystalline film * zinc oxide Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 7.504, year: 2016

Dopant concentration dependence of radiation-induced positive hysteresis of Ce:GSO and Ce:GSOZ

International Nuclear Information System (INIS)

Yanagida, Takayuki; Fujimoto, Yutaka; Watanabe, Kenichi

2014-01-01

Positive hysteresis and radiation tolerance to high-dose radiation exposure were investigated for Ce 0.5, 1, and 1.5%-doped Gd 2 SiO 5 (GSO) and for Zr co-doped GSO with the same Ce concentrations (GSOZ). When they were irradiated by 200–800 Gy 60 Co in 200 Gy steps, all Ce-doped GSO samples exhibited light yield enhancement (positive hysteresis). On the other hand, the light yield of GSOZ decreased greatly. Ce 0.5%-doped GSO showed the highest positive hysteresis, with ∼20% light yield enhancement. When the Ce concentration was increased, the positive hysteresis became weaker. - Highlights: • Positive hysteresis Ce 0.5, 1, and 1.5% doped GSO and GSOZ are studied. • Ce 0.5, 1, and 1.5% doped GSO show the positive hysteresis by 2–8 M rad 60 Co irradiation. • Ce 0.5, 1, and 1.5% doped GSOZ do not show the positive hysteresis. • By Zn co-doping, radiation tolerance of GSO becomes weaker. • By dense Ce doping, radiation tolerance of GSO and GSOZ are improved

Dopant activation in Sn-doped Ga{sub 2}O{sub 3} investigated by X-ray absorption spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Siah, S. C., E-mail: sincheng@alum.mit.edu; Brandt, R. E.; Jaramillo, R.; Buonassisi, T., E-mail: buonassisi@mit.edu [Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Lim, K. [SLAC National Accelerator Laboratory, Stanford Synchrotron Radiation Lightsource, Menlo Park, California 94025 (United States); Department of Materials Science and Engineering, Stanford University, Stanford, California 94305 (United States); Schelhas, L. T.; Toney, M. F. [SLAC National Accelerator Laboratory, Stanford Synchrotron Radiation Lightsource, Menlo Park, California 94025 (United States); Heinemann, M. D. [PVcomB, Helmholtz-Zentrum Berlin, 12489 Berlin (Germany); Chua, D.; Gordon, R. G. [Department of Chemistry Materials Science and Chemical Biology, Harvard University, Cambridge, Massachusetts 02138 (United States); Wright, J.; Segre, C. U. [Physics Department and CSRRI, Illinois Institute of Technology, Chicago, Illinois 60616 (United States); Perkins, J. D. [National Renewable Energy Laboratory, Golden, Colorado 80401 (United States)

2015-12-21

Doping activity in both beta-phase (β-) and amorphous (a-) Sn-doped gallium oxide (Ga{sub 2}O{sub 3}:Sn) is investigated by X-ray absorption spectroscopy (XAS). A single crystal of β-Ga{sub 2}O{sub 3}:Sn grown using edge-defined film-fed growth at 1725 °C is compared with amorphous Ga{sub 2}O{sub 3}:Sn films deposited at low temperature (<300 °C). Our XAS analyses indicate that activated Sn dopant atoms in conductive single crystal β-Ga{sub 2}O{sub 3}:Sn are present as Sn{sup 4+}, preferentially substituting for Ga at the octahedral site, as predicted by theoretical calculations. In contrast, inactive Sn atoms in resistive a-Ga{sub 2}O{sub 3}:Sn are present in either +2 or +4 charge states depending on growth conditions. These observations suggest the importance of growing Ga{sub 2}O{sub 3}:Sn at high temperature to obtain a crystalline phase and controlling the oxidation state of Sn during growth to achieve dopant activation.

Two dimensional dopant diffusion study by scanning capacitance microscopy and TSUPREM IV process simulation

International Nuclear Information System (INIS)

Kim, J.; McMurray, J. S.; Williams, C. C.; Slinkman, J.

1998-01-01

We report the results of a 2-step two-dimensional (2D) diffusion study by Scanning Capacitance Microscopy (SCM) and 2D TSUPREM IV process simulation. A quantitative 2D dopant profile of gate-like structures consisting heavily implanted n+ regions separated by a lighter doped n-type region underneath 0.56 μm gates is measured with the SCM. The SCM is operated in the constant-change-in-capacitance mode. The 2-D SCM data is converted to dopant density through a physical model of the SCM/silicon interaction. This profile has been directly compared with 2D TSUPREM IV process simulation and used to calibrate the simulation parameters. The sample is then further subjected to an additional diffusion in a furnace for 80 minutes at 1000C. The SCM measurement is repeated on the diffused sample. This final 2D dopant profile is compared with a TSUPREM IV process simulation tuned to fit the earlier profile with no change in the parameters except the temperature and time for the additional diffusion. Our results indicate that there is still a significant disagreement between the two profiles in the lateral direction. TSUPREM IV simulation considerably underestimates the diffusion under the gate region

Secondary ions mass spectroscopy measurements of dopant impurities in highly stressed InGaN laser diodes

International Nuclear Information System (INIS)

Marona, L.; Suski, T.; Perlin, P.; Czernecki, R.; Leszczynski, M.; Bockowski, M.; Jakiela, R.; Najda, S. P.

2011-01-01

We performed a systematic secondary ions mass spectroscopy (SIMS) study of dopant impurities in life-time stressed InGaN laser devices in order to investigate the main degradation mechanism that is observed in nitride laser diodes. A continuous wave (cw) current density of 3 kA/cm 2 was applied to InGaN laser diodes over an extended period of time and we observed the characteristic square root degradation of optical power. We compared the SIMS profiles of Mg, H, and Si impurities in the aged devices and observe that the impurities are remarkably stable over 10 000 h of cw operation. Nor is there any SIMS evidence of p-contact metals penetrating into the semiconductor material. Thus our SIMS results are contrary to what one would expect for impurity diffusion causing the observed square root degradation characteristic.

High-flux solar concentration with imaging designs

Energy Technology Data Exchange (ETDEWEB)

Feuermann, D. [Ben-Gurion University of the Negev (Israel). Jacob Blaustein Institute for Desert Research; Gordon, J.M. [Ben-Gurion University of the Negev (Israel). Jacob Blaustein Institute for Desert Research; Ben-Gurion University of the Negev (Israel). Dept. of Mechanical Engineering; Ries, H. [Ries and Partners, Munich (Germany)

1999-02-01

Most large solar concentrators designed for high flux concentration at high collection efficiency are based on imaging primary mirrors and nonimaging secondary concentrators. In this paper, we offer an alternative purely imaging two-stage solar concentrator that can attain high flux concentration at high collection efficiency. Possible practical virtues include: (1) an inherent large gap between absorber and secondary mirror; (2) a restricted angular range on the absorber; and (3) an upward-facing receiver where collected energy can be extracted via the (shaded) apex of the parabola. We use efficiency-concentration plots to characterize the solar concentrators considered, and to evaluate the potential improvements with secondary concentrators. (author)

Two opposite hysteresis curves in semiconductors with mobile dopants

OpenAIRE

Lee, Jae Sung; Lee, Shin Buhm; Kahng, Byungnam; Noh, Tae Won

2012-01-01

Recent experimental researches on semiconductors with mobile dopants (SMD) have reported unconventional hysteretic current-voltage (I-V) curves, which form dynamically in either one of the two opposite directions, the counter-figure-eight and figure-eight ways. However the fundamental theory for the formation of the two directions is still absent, and this poses a major barrier for researches oriented to applications. Here, we introduce a theoretical model to explain the origin of the two dir...

Advances in highly doped upconversion nanoparticles.

Science.gov (United States)

Wen, Shihui; Zhou, Jiajia; Zheng, Kezhi; Bednarkiewicz, Artur; Liu, Xiaogang; Jin, Dayong

2018-06-20

Lanthanide-doped upconversion nanoparticles (UCNPs) are capable of converting near-infra-red excitation into visible and ultraviolet emission. Their unique optical properties have advanced a broad range of applications, such as fluorescent microscopy, deep-tissue bioimaging, nanomedicine, optogenetics, security labelling and volumetric display. However, the constraint of concentration quenching on upconversion luminescence has hampered the nanoscience community to develop bright UCNPs with a large number of dopants. This review surveys recent advances in developing highly doped UCNPs, highlights the strategies that bypass the concentration quenching effect, and discusses new optical properties as well as emerging applications enabled by these nanoparticles.

Dopant-site-dependent scattering by dislocations in epitaxial films of perovskite semiconductor BaSnO3

Directory of Open Access Journals (Sweden)

Useong Kim

2014-05-01

Full Text Available We studied the conduction mechanism in Sb-doped BaSnO3 epitaxial films, and compared its behavior with that of the mechanism of its counterpart, La-doped BaSnO3. We found that the electron mobility in BaSnO3 films was reduced by almost 7 times when the dopant was changed from La to Sb, despite little change in the effective mass of the carriers. This indicates that the scattering rate of conduction electrons in the BaSnO3 system is strongly affected by the site at which the dopants are located. More importantly, we found that electron scattering by threading dislocations also depends critically on the dopant site. We propose that the large enhancement of scattering by the threading dislocations in Sb-doped BaSnO3 films is caused by the combination effect of the change in the distribution of Sb impurities in the films, the formation of the Sb impurity clusters near the threading dislocations, and the conduction electron clustering near the Sb impurities.

The Effect of Dopant-Free Hole-Transport Polymers on Charge Generation and Recombination in Cesium-Bismuth-Iodide Solar Cells.

Science.gov (United States)

Zhu, Huimin; Johansson, Malin B; Johansson, Erik M J

2018-03-22

The photovoltaic characteristics of CsBi 3 I 10 -based solar cells with three dopant-free hole-conducting polymers are investigated. The effect on charge generation and charge recombination in the solar cells using the different polymers is studied and the results indicate that the choice of polymer strongly affects the device properties. Interestingly, for the solar cell with poly[[2,3-bis(3-octyloxyphenyl)-5,8-quinoxalinediyl]-2,5-thiophenediyl] (TQ1), the photon-to-current conversion spectrum is highly improved in the red wavelength region, suggesting that the polymer also contributes to the photocurrent generation in this case. This report provides a new direction for further optimization of Bi-halide solar cells by using dopant-free hole-transporting polymers and shows that the energy levels and the interaction between the Bi-halide and the conducting polymers are very important for solar cell performance. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

A molecular dynamics study on the oxygen diffusion in doped fluorites: the effect of the dopant distribution

Energy Technology Data Exchange (ETDEWEB)

Tarancon, A. [M2E/XaRMAE/IREC, Department of Advanced Materials for Energy Applications, Catalonia Institute for Energy Research (IREC), Josep Pla 2, Torre 2, B2, 08019 Barcelona (Spain); Morata, A.; Peiro, F. [MIND/XaRMAE/IN2UB, Department of Electronics, University of Barcelona, Marti i Franques 1, 08028 Barcelona (Spain); Dezanneau, G. [Laboratoire Structures, Proprietes et Modelisation des Solides, Grande Voie des Vignes, Ecole Centrale Paris, F-92295 Chatenay-Malabry Cedex (France)

2011-02-15

The effect of the dopant distribution on the oxygen diffusion in doped fluorites typically used for solid oxide fuel cells electrolyte applications has been analysed by using molecular dynamics simulations. The oxygen mass transport in both yttria-stabilized zirconia (YSZ) and gadolinia-doped ceria has been studied and compared in the range of temperatures between 1,159 and 1,959 K. A new methodology based on the analysis of local environments is used to describe the diffusion process at an atomic scale. Preferred vacancy migration pathways, most suitable conduction models, energy landscapes and jump efficiency have been detailed for each material. Finally, a particular case of non-random distribution of dopants in YSZ is presented in order to quantitatively evaluate the effect of the dopant pattern on the mass transport properties and the potential of the methodology developed here for understanding and foreseeing real configurations at the nanoscale. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

High resistance to sulfur poisoning of Ni with copper skin under electric field

Energy Technology Data Exchange (ETDEWEB)

Xu, Xiaopei; Zhang, Yanxing [College of Physics and Materials Science, Henan Normal University, Xinxiang, Henan 453007 (China); Yang, Zongxian, E-mail: yzx@henannu.edu.cn [College of Physics and Materials Science, Henan Normal University, Xinxiang, Henan 453007 (China); Collaborative Innovation Center of Nano Functional Materials and Applications, Kaifeng, Henan Province (China)

2017-02-12

The effects of sulfur poisoning on the (1 0 0), (1 1 0) and (1 1 1) surfaces of pure Ni and Cu/Ni alloy are studied in consideration of the effect of electric field. The effects of Cu dopants on the S poisoning characteristics are analyzed by the means of the density functional theory results in combination with thermodynamics data using the ab initio atomistic thermodynamic method. When the Cu concentration increases to 50% on the surface layer of the Cu/Ni alloy, the (1 1 0) surface becomes the most vulnerable to the sulfur poisoning. Ni with a copper skin can mostly decrease the sulfur poisoning effect. Especially under the electric field of 1.0 V/Å, the sulfur adsorption and phase transition temperature can be further reduced. We therefore propose that Ni surfaces with copper skin can be very effective to improve the resistance to sulfur poisoning of the Ni anode under high electric field. - Highlights: • The electric field and Cu dopant effects on S poisoning feature of Ni are analyzed. • The present of large electric field can enhance S tolerance. • Cu dopant concentration affect the surface electronic structure of Ni. • 100% Cu doping on surface Ni layer can mostly decrease the sulfur poison.

Dependence of the Mg-related acceptor ionization energy with the acceptor concentration in p-type GaN layers grown by molecular beam epitaxy

International Nuclear Information System (INIS)

Brochen, Stéphane; Brault, Julien; Chenot, Sébastien; Dussaigne, Amélie; Leroux, Mathieu; Damilano, Benjamin

2013-01-01

Hall effect and capacitance-voltage C(V) measurements were performed on p-type GaN:Mg layers grown on GaN templates by molecular beam epitaxy with a high range of Mg-doping concentrations. The free hole density and the effective dopant concentration N A −N D as a function of magnesium incorporation measured by secondary ion mass spectroscopy clearly reveal both a magnesium doping efficiency up to 90% and a strong dependence of the acceptor ionization energy Ea with the acceptor concentration N A . These experimental observations highlight an isolated acceptor binding energy of 245±25 meV compatible, at high acceptor concentration, with the achievement of p-type GaN:Mg layers with a hole concentration at room temperature close to 10 19 cm −3

Semiconductive materials and associated uses thereof

Science.gov (United States)

Lynn, Kelvin; Jones, Kelly; Ciampi, Guido

2012-10-09

High rate radiation detectors are disclosed herein. The detectors include a detector material disposed inside the container, the detector material containing cadmium, tellurium, and zinc, a first dopant containing at least one of aluminum, chlorine, and indium, and a second dopant containing a rare earth metal. The first dopant has a concentration of about 500 to about 20,000 atomic parts per billion, and the second dopant has a concentration of about 200 to about 20,000 atomic parts per billion.

Quantitative Characterization of the Nanoscale Local Lattice Strain Induced by Sr Dopants in La1.92Sr0.08CuO4

Science.gov (United States)

Lin, J. Q.; Liu, X.; Blackburn, E.; Wakimoto, S.; Ding, H.; Islam, Z.; Sinha, S. K.

2018-05-01

The nanometer scale lattice deformation brought about by the dopants in the high temperature superconducting cuprate La2 -xSrx CuO4 (x =0.08 ) was investigated by measuring the associated x-ray diffuse scattering around multiple Bragg peaks. A characteristic diffuse scattering pattern was observed, which can be well described by continuum elastic theory. With the fitted dipole force parameters, the acoustic-type lattice deformation pattern was reconstructed and found to be of similar size to lattice thermal vibration at 7 K. Our results address the long-term concern of dopant introduced local lattice inhomogeneity, and show that the associated nanometer scale lattice deformation is marginal and cannot, alone, be responsible for the patched variation in the spectral gaps observed with scanning tunneling microscopy in the cuprates.

The Role of Dopant Ions on Charge Injection and Transport in Electrochemically Doped Quantum Dot Films.

Science.gov (United States)

Gudjonsdottir, Solrun; van der Stam, Ward; Kirkwood, Nicholas; Evers, Wiel H; Houtepen, Arjan J

2018-05-16

Control over the charge density is very important for implementation of colloidal semiconductor nanocrystals into various optoelectronic applications. A promising approach to dope nanocrystal assemblies is charge injection by electrochemistry, in which the charge compensating electrolyte ions can be regarded as external dopant ions. To gain insight into the doping mechanism and the role of the external dopant ions, we investigate charge injection in ZnO nanocrystal assemblies for a large series of charge compensating electrolyte ions with spectroelectrochemical and electrochemical transistor measurements. We show that charge injection is limited by the diffusion of cations in the nanocrystal films as their diffusion coefficient are found to be ∼7 orders of magnitude lower than those of electrons. We further show that the rate of charge injection depends strongly on the cation size and cation concentration. Strikingly, the onset of electron injection varies up to 0.4 V, depending on the size of the electrolyte cation. For the small ions Li + and Na + the onset is at significantly less negative potentials. For larger ions (K + , quaternary ammonium ions) the onset is always at the same, more negative potential, suggesting that intercalation may take place for Li + and Na + . Finally, we show that the nature of the charge compensating cation does not affect the source-drain electronic conductivity and mobility, indicating that shallow donor levels from intercalating ions fully hybridize with the quantum confined energy levels and that the reorganization energy due to intercalating ions does not strongly affect electron transport in these nanocrystal assemblies.

The Role of Dopant Ions on Charge Injection and Transport in Electrochemically Doped Quantum Dot Films

Science.gov (United States)

2018-01-01

Control over the charge density is very important for implementation of colloidal semiconductor nanocrystals into various optoelectronic applications. A promising approach to dope nanocrystal assemblies is charge injection by electrochemistry, in which the charge compensating electrolyte ions can be regarded as external dopant ions. To gain insight into the doping mechanism and the role of the external dopant ions, we investigate charge injection in ZnO nanocrystal assemblies for a large series of charge compensating electrolyte ions with spectroelectrochemical and electrochemical transistor measurements. We show that charge injection is limited by the diffusion of cations in the nanocrystal films as their diffusion coefficient are found to be ∼7 orders of magnitude lower than those of electrons. We further show that the rate of charge injection depends strongly on the cation size and cation concentration. Strikingly, the onset of electron injection varies up to 0.4 V, depending on the size of the electrolyte cation. For the small ions Li+ and Na+ the onset is at significantly less negative potentials. For larger ions (K+, quaternary ammonium ions) the onset is always at the same, more negative potential, suggesting that intercalation may take place for Li+ and Na+. Finally, we show that the nature of the charge compensating cation does not affect the source-drain electronic conductivity and mobility, indicating that shallow donor levels from intercalating ions fully hybridize with the quantum confined energy levels and that the reorganization energy due to intercalating ions does not strongly affect electron transport in these nanocrystal assemblies. PMID:29718666

Current status of models for transient phenomena in dopant diffusion and activation

International Nuclear Information System (INIS)

Pichler, P.; Stiebel, D.

2002-01-01

Transient phenomena caused by ion-implantation processes have been studied for more than 25 years now with a continuously increasing number of research articles published in this field per year. One driving force of this research is the ongoing miniaturization of ULSI MOS and bipolar technology which uses extensively the capabilities of technology-computer-aided-design (TCAD). The other driving force which attracts also academic institutions and research institutes is the high complexity of the phenomena, involving the interaction of dopants, intrinsic point defects, extended defects and impurities like carbon as well as the interactions of mobile defects with surfaces and interfaces and their redistribution in multilayer structures. This paper outlines some recent advances towards a quantitative description of such phenomena

n-Dopants Based on Dimers of Benzimidazoline Radicals: Structures and Mechanism of Redox Reactions.

Science.gov (United States)

Zhang, Siyuan; Naab, Benjamin D; Jucov, Evgheni V; Parkin, Sean; Evans, Eric G B; Millhauser, Glenn L; Timofeeva, Tatiana V; Risko, Chad; Brédas, Jean-Luc; Bao, Zhenan; Barlow, Stephen; Marder, Seth R

2015-07-20

Dimers of 2-substituted N,N'-dimethylbenzimidazoline radicals, (2-Y-DMBI)2 (Y=cyclohexyl (Cyc), ferrocenyl (Fc), ruthenocenyl (Rc)), have recently been reported as n-dopants for organic semiconductors. Here their structural and energetic characteristics are reported, along with the mechanisms by which they react with acceptors, A (PCBM, TIPS-pentacene), in solution. X-ray data and DFT calculations both indicate a longer C-C bond for (2-Cyc-DMBI)2 than (2-Fc-DMBI)2 , yet DFT and ESR data show that the latter dissociates more readily due to stabilization of the radical by Fc. Depending on the energetics of dimer (D2 ) dissociation and of D2 -to-A electron transfer, D2 reacts with A to form D(+) and A(-) by either of two mechanisms, differing in whether the first step is endergonic dissociation or endergonic electron transfer. However, the D(+) /0.5 D2 redox potentials-the effective reducing strengths of the dimers-vary little within the series (ca. -1.9 V vs. FeCp2 (+/0) ) (Cp=cyclopentadienyl) due to cancelation of trends in the D(+/0) potential and D2 dissociation energy. The implications of these findings for use of these dimers as n-dopants, and for future dopant design, are discussed. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

n-Dopants Based on Dimers of Benzimidazoline Radicals: Structures and Mechanism of Redox Reactions

KAUST Repository

Zhang, Siyuan

2015-06-18

Dimers of 2-substituted N,N\\'-dimethylbenzimidazoline radicals, (2-Y-DMBI)2 (Y=cyclohexyl (Cyc), ferrocenyl (Fc), ruthenocenyl (Rc)), have recently been reported as n-dopants for organic semiconductors. Here their structural and energetic characteristics are reported, along with the mechanisms by which they react with acceptors, A (PCBM, TIPS-pentacene), in solution. X-ray data and DFT calculations both indicate a longer C-C bond for (2-Cyc-DMBI)2 than (2-Fc-DMBI)2, yet DFT and ESR data show that the latter dissociates more readily due to stabilization of the radical by Fc. Depending on the energetics of dimer (D2) dissociation and of D2-to-A electron transfer, D2 reacts with A to form D+ and A- by either of two mechanisms, differing in whether the first step is endergonic dissociation or endergonic electron transfer. However, the D+/0.5D2 redox potentials-the effective reducing strengths of the dimers-vary little within the series (ca. -1.9V vs. FeCp2+/0) (Cp=cyclopentadienyl) due to cancelation of trends in the D+/0 potential and D2 dissociation energy. The implications of these findings for use of these dimers as n-dopants, and for future dopant design, are discussed. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

n-Dopants Based on Dimers of Benzimidazoline Radicals: Structures and Mechanism of Redox Reactions

KAUST Repository

Zhang, Siyuan; Naab, Benjamin D.; Jucov, Evgheni V.; Parkin, Sean; Evans, Eric G B; Millhauser, Glenn L.; Timofeeva, Tatiana V.; Risko, Chad; Bredas, Jean-Luc; Bao, Zhenan; Barlow, Stephen; Marder, Seth R.

2015-01-01

Dimers of 2-substituted N,N'-dimethylbenzimidazoline radicals, (2-Y-DMBI)2 (Y=cyclohexyl (Cyc), ferrocenyl (Fc), ruthenocenyl (Rc)), have recently been reported as n-dopants for organic semiconductors. Here their structural and energetic characteristics are reported, along with the mechanisms by which they react with acceptors, A (PCBM, TIPS-pentacene), in solution. X-ray data and DFT calculations both indicate a longer C-C bond for (2-Cyc-DMBI)2 than (2-Fc-DMBI)2, yet DFT and ESR data show that the latter dissociates more readily due to stabilization of the radical by Fc. Depending on the energetics of dimer (D2) dissociation and of D2-to-A electron transfer, D2 reacts with A to form D+ and A- by either of two mechanisms, differing in whether the first step is endergonic dissociation or endergonic electron transfer. However, the D+/0.5D2 redox potentials-the effective reducing strengths of the dimers-vary little within the series (ca. -1.9V vs. FeCp2+/0) (Cp=cyclopentadienyl) due to cancelation of trends in the D+/0 potential and D2 dissociation energy. The implications of these findings for use of these dimers as n-dopants, and for future dopant design, are discussed. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Atomic-level spatial distributions of dopants on silicon surfaces: toward a microscopic understanding of surface chemical reactivity

Science.gov (United States)

Hamers, Robert J.; Wang, Yajun; Shan, Jun

1996-11-01

We have investigated the interaction of phosphine (PH 3) and diborane (B 2H 6) with the Si(001) surface using scanning tunneling microscopy, infrared spectroscopy, and ab initio molecular orbital calculations. Experiment and theory show that the formation of PSi heterodimers is energetically favorable compared with formation of PP dimers. The stability of the heterodimers arises from a large strain energy associated with formation of PP dimers. At moderate P coverages, the formation of PSi heterodimers leaves the surface with few locations where there are two adjacent reactive sites. This in turn modifies the chemical reactivity toward species such as PH 3, which require only one site to adsorb but require two adjacent sites to dissociate. Boron on Si(001) strongly segregates into localized regions of high boron concentration, separated by large regions of clean Si. This leads to a spatially-modulated chemical reactivity which during subsequent growth by chemical vapor deposition (CVD) leads to formation of a rough surface. The implications of the atomic-level spatial distribution of dopants on the rates and mechanisms of CVD growth processes are discussed.

Ternary logic implemented on a single dopant atom field effect silicon transistor

NARCIS (Netherlands)

Klein, M.; Mol, J.A.; Verduijn, J.; Lansbergen, G.P.; Rogge, S.; Levine, R.D.; Remacle, F.

2010-01-01

We provide an experimental proof of principle for a ternary multiplier realized in terms of the charge state of a single dopant atom embedded in a fin field effect transistor (Fin-FET). Robust reading of the logic output is made possible by using two channels to measure the current flowing through

Highly doped layer for tunnel junctions in solar cells

Science.gov (United States)

Fetzer, Christopher M.

2017-08-01

A highly doped layer for interconnecting tunnel junctions in multijunction solar cells is presented. The highly doped layer is a delta doped layer in one or both layers of a tunnel diode junction used to connect two or more p-on-n or n-on-p solar cells in a multijunction solar cell. A delta doped layer is made by interrupting the epitaxial growth of one of the layers of the tunnel diode, depositing a delta dopant at a concentration substantially greater than the concentration used in growing the layer of the tunnel diode, and then continuing to epitaxially grow the remaining tunnel diode.

Horizontally staggered lightguide solar concentrator with lateral displacement tracking for high concentration applications.

Science.gov (United States)

Ma, Hongcai; Wu, Lin

2015-07-10

We present the design of a horizontally staggered lightguide solar concentrator with lateral displacement tracking for high concentration applications. This solar concentrator consists of an array of telecentric primary concentrators, a horizontally staggered lightguide layer, and a vertically tapered lightguide layer. The primary concentrator is realized by two plano-aspheric lenses with lateral movement and maintains a high F-number over an angle range of ±23.5°. The results of the simulations show that the solar concentrator achieves a high concentration ratio of 500× with ±0.5° of acceptance angle by a single-axis tracker and dual lateral translation stages.

The effect of random dopant fluctuation on threshold voltage and drain current variation in junctionless nanotransistors

International Nuclear Information System (INIS)

Rezapour, Arash; Rezapour, Pegah

2015-01-01

We investigate the effect of dopant random fluctuation on threshold voltage and drain current variation in a two-gate nanoscale transistor. We used a quantum-corrected technology computer aided design simulation to run the simulation (10000 randomizations). With this simulation, we could study the effects of varying the dimensions (length and width), and thicknesses of oxide and dopant factors of a transistor on the threshold voltage and drain current in subthreshold region (off) and overthreshold (on). It was found that in the subthreshold region the variability of the drain current and threshold voltage is relatively fixed while in the overthreshold region the variability of the threshold voltage and drain current decreases remarkably, despite the slight reduction of gate voltage diffusion (compared with that of the subthreshold). These results have been interpreted by using previously reported models for threshold current variability, load displacement, and simple analytical calculations. Scaling analysis shows that the variability of the characteristics of this semiconductor increases as the effects of the short channel increases. Therefore, with a slight increase of length and a reduction of width, oxide thickness, and dopant factor, we could correct the effect of the short channel. (paper)

Cementification for radioactive waste including high-concentration sodium sulfate and high-concentration radioactive nuclide

International Nuclear Information System (INIS)

Miyamoto, Shinya; Sato, Tatsuaki; Sasoh, Michitaka; Sakurai, Jiro; Takada, Takao

2005-01-01

For the cementification of radioactive waste that has large concentrations of sodium sulfate and radioactive nuclide, a way of fixation for sulfate ion was studied comprising the pH control of water in contact with the cement solid, and the removal of the excess water from the cement matrix to prevent hydrogen gas generation with radiolysis. It was confirmed that the sulfate ion concentration in the contacted water with the cement solid is decreased with the formation of ettringite or barium sulfate before solidification, the pH value of the pore water in the cement solid can control less than 12.5 by the application of zeolite and a low-alkali cement such as alumina cement or fly ash mixed cement, and removal of the excess water from the cement matrix by heating is possible with aggregate addition. Consequently, radioactive waste including high-concentration sodium sulfate and high-concentration radioactive nuclide can be solidified with cementitious materials. (author)

Low-temperature thermal decomposition of heavy petroleum distillates: interconnection between the electrical properties and concentration of paramagnetic centres

Science.gov (United States)

Dolomatov, M.; Gafurov, M.; Rodionov, A.; Mamin, G.; González, L. Miquel; Vakhin, A.; Petrov, A.; Bakhtizin, R.; Khairudinov, I.; Orlinskii, S.

2018-05-01

Changes of paramagnetic centers (PC) concentration in petroleum dispersed systems (PDS) are studied in the process of low-temperature thermolysis. Complex investigation of physicochemical, rheological and electrophysical properties of high-boiling oil fractions is performed. Based on the analysis of the experimental results it can be concluded that the PDS under investigation can be regarded as amorphous broadband organic semiconductors for which PC plays a role of dopant. It shows the perspectives of the asphaltenes usage as a basis for the photovoltaic devices.

Dopant-site-dependent scattering by dislocations in epitaxial films of perovskite semiconductor BaSnO{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Kim, Useong; Park, Chulkwon; Kim, Rokyeon; Mun, Hyo Sik; Kim, Hoon Min; Kim, Namwook; Yu, Jaejun; Char, Kookrin, E-mail: kchar@phya.snu.ac.kr [Center for Strongly Correlated Materials Research, Department of Physics and Astronomy, Seoul National University, Seoul 151-747 (Korea, Republic of); Ha, Taewoo; Kim, Jae Hoon [Department of Physics, Yonsei University, Seoul 120-749 (Korea, Republic of); Kim, Hyung Joon; Kim, Tai Hoon; Kim, Kee Hoon [Center for Novel States of Complex Materials Research, Department of Physics and Astronomy, Seoul National University, Seoul 151-747 (Korea, Republic of)

2014-05-01

We studied the conduction mechanism in Sb-doped BaSnO{sub 3} epitaxial films, and compared its behavior with that of the mechanism of its counterpart, La-doped BaSnO{sub 3}. We found that the electron mobility in BaSnO{sub 3} films was reduced by almost 7 times when the dopant was changed from La to Sb, despite little change in the effective mass of the carriers. This indicates that the scattering rate of conduction electrons in the BaSnO{sub 3} system is strongly affected by the site at which the dopants are located. More importantly, we found that electron scattering by threading dislocations also depends critically on the dopant site. We propose that the large enhancement of scattering by the threading dislocations in Sb-doped BaSnO{sub 3} films is caused by the combination effect of the change in the distribution of Sb impurities in the films, the formation of the Sb impurity clusters near the threading dislocations, and the conduction electron clustering near the Sb impurities.

Theoretical study of nitrogen-doped graphene nanoflakes: Stability and spectroscopy depending on dopant types and flake sizes.

Science.gov (United States)

Lin, Chih-Kai

2018-03-05

As nitrogen-doped graphene has been widely applied in optoelectronic devices and catalytic reactions, in this work we have investigated where the nitrogen atoms tend to reside in the material and how they affect the electron density and spectroscopic properties from a theoretical point of view. DFT calculations on N-doped hexagonal and rectangular graphene nanoflakes (GNFs) showed that nitrogen atoms locating on zigzag edges are obviously more stable than those on armchair edges or inside flakes, and interestingly, the N-hydrogenated pyridine moiety could be preferable to pure pyridine moiety in large models. The UV-vis absorption spectra of these nitrogen-doped GNFs display strong dependence on flake sizes, where the larger flakes have their major peaks in lower energy ranges. Moreover, the spectra exhibit different connections to various dopant types and positions: the graphitic-type dopant species present large variety in absorption profiles, while the pyridinic-type ones show extraordinary uniform stability and spectra independent of dopant positions/numbers and hence are hardly distinguishable from each other. © 2018 Wiley Periodicals, Inc. © 2018 Wiley Periodicals, Inc.

Solutions to defect-related problems in implanted silicon by controlled injection of vacancies by high-energy ion irradiation

International Nuclear Information System (INIS)

Roth, E.G.; Holland, O.W.; Duggan, J.L.

1999-01-01

Amorphization and a dual implant technique have been used to manipulate residual defects that persist following implantation and post-implant thermal treatments. Residual defects can often be attributed to ion-induced defect excesses. A defect is considered to be excess when it occurs in a localized region at a concentration greater than its complement. Sources of excess defects include spatially separated Frenkel pairs, excess interstitials resulting from the implanted atoms, and sputtering. Preamorphizing prior to dopant implantation has been proposed to eliminate dopant broadening due to ion channeling as well as dopant diffusion during subsequent annealing. However, transient-enhanced diffusion (TED) of implanted boron has been observed in pre-amorphized Si. The defects driving this enhanced boron diffusion are thought to be the extended interstitial-type defects that form below the amorphous-crystalline interface during implantation. A dual implantation process was applied in an attempt to reduce or eliminate this interfacial defect band. High-energy, ion implantation is known to inject a vacancy excess in this region. Vacancies were implanted at a concentration coincident with the excess interstitials below the a-c interface to promote recombination between the two defect species. Preliminary results indicate that a critical fluence, i.e., a sufficient vacancy concentration, will eliminate the interstitial defects. The effect of the reduction or elimination of these interfacial defects upon TED of boron will be discussed. Rutherford backscattering/channeling and cross section transmission electron microscopy analyses were used to characterize the defect structure within the implanted layer. Secondary ion mass spectrometry was used to profile the dopant distributions. copyright 1999 American Institute of Physics

Study of Sequential Dexter Energy Transfer in High Efficient Phosphorescent White Organic Light-Emitting Diodes with Single Emissive Layer

Science.gov (United States)

Kim, Jin Wook; You, Seung Il; Kim, Nam Ho; Yoon, Ju-An; Cheah, Kok Wai; Zhu, Fu Rong; Kim, Woo Young

2014-11-01

In this study, we report our effort to realize high performance single emissive layer three color white phosphorescent organic light emitting diodes (PHOLEDs) through sequential Dexter energy transfer of blue, green and red dopants. The PHOLEDs had a structure of; ITO(1500 Å)/NPB(700 Å)/mCP:Firpic-x%:Ir(ppy)3-0.5%:Ir(piq)3-y%(300 Å)/TPBi(300 Å)/Liq(20 Å)/Al(1200 Å). The dopant concentrations of FIrpic, Ir(ppy)3 and Ir(piq)3 were adjusted and optimized to facilitate the preferred energy transfer processes attaining both the best luminous efficiency and CIE color coordinates. The presence of a deep trapping center for charge carriers in the emissive layer was confirmed by the observed red shift in electroluminescent spectra. White PHOLEDs, with phosphorescent dopant concentrations of FIrpic-8.0%:Ir(ppy)3-0.5%:Ir(piq)3-0.5% in the mCP host of the single emissive layer, had a maximum luminescence of 37,810 cd/m2 at 11 V and a luminous efficiency of 48.10 cd/A at 5 V with CIE color coordinates of (0.35, 0.41).

Crystal structure, chemical bond and enhanced performance of β-Zn{sub 4}Sb{sub 3} compounds with interstitial indium dopant

Energy Technology Data Exchange (ETDEWEB)

Tang, Dingguo [State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan University of Technology, Wuhan 430070 (China); Key Laboratory of Catalysis and Materials Science of the State Ethnic Affair Commission and Ministry of Education, South-Central University for Nationalities, Wuhan 430074 (China); Zhao, Wenyu, E-mail: wyzhao@whut.edu.cn [State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan University of Technology, Wuhan 430070 (China); Yu, Jian; Wei, Ping; Zhou, Hongyu; Zhu, Wanting [State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan University of Technology, Wuhan 430070 (China); Zhang, Qingjie, E-mail: zhangqj@whut.edu.cn [State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan University of Technology, Wuhan 430070 (China)

2014-07-15

Highlights: • The interstitial In dopant leads to the local structural perturbations in β-Zn{sub 4}Sb{sub 3}. • The simultaneous increases in α and σ are observed in the In-doped Zn{sub 4}Sb{sub 3} compounds. • The In dopant plays different doping behaviors by the dopant contents in the samples. • A maximum ZT of 1.41 at 700 K is achieved for the In-doped Zn{sub 4}Sb{sub 3} compounds. - Abstract: In-doped β-Zn{sub 4}Sb{sub 3} compounds (Zn{sub 4−x}In{sub x}Sb{sub 3}, 0 ⩽ x ⩽ 0.24) were prepared by melt-quenching and spark plasma sintering technology in the work. The resultant samples were systematically investigated by X-ray diffraction, X-ray photoelectron spectroscopy, differential scanning calorimetry and thermoelectric property measurements. The In dopant was identified to preferentially occupy the interstitial site in β-Zn{sub 4}Sb{sub 3} and led to the local structural perturbations near the 12c Sb2 and 36f Zn1 sites. The Auger parameters of Zn and Sb indicated that the increase in the valence of Zn was attributed to the charge transfer from Zn to In atoms. The binding energies of In 3d{sub 5/2} core level showed that the interstitial In dopant was n-type dopant (In{sup 3+}) in slightly In-doped Zn{sub 4−x}In{sub x}Sb{sub 3}, but acted as acceptor and was p-type dopant (In{sup +}) in heavily In-doped ones. The discovery provides a reasonable explanation for the puzzled relation between σ and x for Zn{sub 4−x}In{sub x}Sb{sub 3}. Simultaneously increasing the electrical conductivity and Seebeck coefficient of Zn{sub 4−x}In{sub x}Sb{sub 3} can be realized through the local structural perturbations. The significantly enhanced power factor and the intrinsic low thermal conductivity resulted in a remarkable increase in the dimensionless figure of merit (ZT). The highest ZT reached 1.41 at 700 K for Zn{sub 3.82}In{sub 0.18}Sb{sub 3} and increased by 68% compared with that of the undoped β-Zn{sub 4}Sb{sub 3}.

Synthesis and characterization of the polyaniline dopant Schiff base

Directory of Open Access Journals (Sweden)

Mirian Y. Matsumoto

2012-06-01

Full Text Available The Schiff base, N-salicilidenoanilina was used as dopant to induce polymerization of aniline and thus preparing polyaniline (PAni. The different conditions of preparation, including Schiff base structure, and the dosage of acidity reaction medium, were investigated to discuss the influence of these conditions relative conductivity of the resulting samples. The products were also characterized by Fourier transform infrared (FTIR, ultraviolet-visible (UV-Vis, electrochemical impedance spectroscopy (EIE. The results showed the synthesis conditions play an important in the formation and the final properties of the polyaniline

Shallow dopants in nanostructered and in isotopically engineered silicon

Energy Technology Data Exchange (ETDEWEB)

Stegner, Andre Rainer

2011-01-15

This work addressed two major topics. The first part was dedicated to the investigation of the doping properties of Si nanostructures. There, we have reported our results on Si nanoparticles with particular focus on questions concerning the atomic incorporation efficiency of dopants, their compensation by surface defects, and the change of their localization due to confinement effects. In the second part of this thesis, we have addressed several open questions concerning the spin properties of shallow acceptor states in bulk Si crystals with different isotope compositions. As far as the first part is concerned, ESR and SIMS have been used to quantitatively investigate the P doping efficiency and the interrelationship of Si-db states and P doping in freestanding Si-NCs over a wide range of diameters. Two types of Si-db defect states, the P{sub b} center and the D center, were identified, where the P{sub b} centers are found at concentrations comparable to bulk Si/SiO{sub 2} interfaces. Moreover, the incorporation of P donors and B acceptors in amorphous Si nanoparticles was demonstrated via ESR. Employing EDMR, we investigated the spin-dependent transport through Si-NC networks. The selectivity and the high sensitivity of EDMR enabled the observation of isolated neutral donor states, which exhibit a characteristic hyperfine splitting in samples with very small diameters. This opened up a possibility for the direct study of the properties of the donor wave function in Si-NCs. To this end, we have used the hyperfine splitting as a spectroscopic measure to monitor the localization of donor wave functions when going from the bulk to the nanoscale. As far as the spin properties of shallow acceptors in Si are concerned, we have addressed a number of fundamental questions concerning the line shape, the magnitude of the residual broadening and the substructure of the boron resonances observed in low-temperature EPR experiments. Performing EPR measurements on different

What is the origin of concentration quenching of Cu"+ luminescence in glass?

International Nuclear Information System (INIS)

Jiménez, José A.

2016-01-01

Monovalent copper-doped luminescent glasses are attractive materials for white light-emitting devices, photonic waveguides, and solar spectral conversion in photovoltaic cells. However, the occurrence of concentration quenching in such is not fully understood at present. In this work, calcium-phosphate glasses with high concentrations of luminescent Cu"+ ions have been prepared by a simple melt-quench method via CuO and SnO co-doping. The aim is to elucidate the origin of concentration quenching of Cu"+ light emission. A spectroscopic characterization was carried out by optical absorption and photoluminescence (PL) spectroscopy including emission decay dynamics. The concentrations of both CuO and SnO dopants were varied as 5, 10 and 15 mol%. Monovalent copper content is estimated in the CuO/SnO-containing glasses following the assessment of the concentration dependence of Cu"2"+ absorption in the visible for CuO singly-doped glasses. Contrary to the conventionally acknowledged direct Cu"+→Cu"2"+ transfer, the data supports a Cu"+–Cu"+ energy migration channel at the origin of the PL quenching.

Determination of gold and cobalt dopants in advanced materials based on tin oxide by slurry sampling high-resolution continuum source graphite furnace atomic absorption spectrometry

Science.gov (United States)

Filatova, Daria G.; Eskina, Vasilina V.; Baranovskaya, Vasilisa B.; Vladimirova, Svetlana A.; Gaskov, Alexander M.; Rumyantseva, Marina N.; Karpov, Yuri A.

2018-02-01

A novel approach is developed for the determination of Co and Au dopants in advanced materials based on tin oxide using high-resolution continuum source graphite furnace atomic absorption spectrometry (HR CS GFAAS) with direct slurry sampling. Sodium carboxylmethylcellulose (Na-CMC) is an effective stabilizer for diluted suspensions. Use Na-CMC allows to transfer the analytes into graphite furnace completely and reproducibly. The relative standard deviation obtained by HR CS GFAAS was not higher than 4%. Accuracy was proven by means inductively coupled plasma mass spectrometry (ICP-MS) in solutions after decomposition as a comparative technique. To determine Au and Co in the volume of SnO2, the acid decomposition conditions (HCl, HF) of the samples were suggested by means of an autoclave in a microwave oven.

Trivalent dopants on ZnO semiconductor obtained by mechanical milling

Energy Technology Data Exchange (ETDEWEB)

Damonte, L.C., E-mail: damonte@fisica.unlp.edu.a [Dto. De Fisica, UNLP, IFLP-CONICET, C.C.67 (1900) La Plata (Argentina); Dto. De Fisica Aplicada, Universidad Politecnica de Valencia, Valencia (Spain); Donderis, V. [Dto. De Ingenieria Electrica, Universidad Politecnica de Valencia, Cami de Vera s/n, 46071 Valencia (Spain); Hernandez-Fenollosa, M.A. [Dto. De Fisica Aplicada, Universidad Politecnica de Valencia, Valencia (Spain)

2009-08-26

Al-doped ZnO powders were obtained by mechanical milling. This n-type oxide material is of interest for application in electronic devices as solar cells. The incorporation of the metal dopant into the ZnO wurtzite structure has been verified by X-ray diffraction, positron annihilation spectroscopy and optical analysis. The optical reflection measurements were strongly affected by the Al incorporation. The positron annihilation spectroscopy constituted an adequate probe to sense the cation substitution in the doped semiconductor.

Trivalent dopants on ZnO semiconductor obtained by mechanical milling

International Nuclear Information System (INIS)

Damonte, L.C.; Donderis, V.; Hernandez-Fenollosa, M.A.

2009-01-01

Al-doped ZnO powders were obtained by mechanical milling. This n-type oxide material is of interest for application in electronic devices as solar cells. The incorporation of the metal dopant into the ZnO wurtzite structure has been verified by X-ray diffraction, positron annihilation spectroscopy and optical analysis. The optical reflection measurements were strongly affected by the Al incorporation. The positron annihilation spectroscopy constituted an adequate probe to sense the cation substitution in the doped semiconductor.

Diagnosing the Stagnation Conditions of MagLIF Implosions Using Co and Kr dopants

Science.gov (United States)

Harding, E. C.; Hansen, S. B.; Harvey-Thompson, A. J.; Weis, M. R.; Hahn, K. D.; Gomez, M. R.; Knapp, P. F.; Slutz, S. A.; Geissel, M.; Ampleford, D. J.; Jennings, C. A.; Peterson, K.; Rochau, G. A.; Doron, R.; Stambulchik, E.; Nedostup, O.; Maron, Y.; Golovkin, I.

2017-10-01

Recent experiments on the Z-machine tested several new diagnostic techniques for investigating the stagnation conditions and the origins of the mix present in a Magnetized Liner Inertial Fusion (MagLIF) target. For the first time we have collected K-shell spectra from a low-concentration, Kr dopant placed in the gaseous D2 fuel. In addition, thin Co coatings were strategically applied to three different internal surfaces of the target in order to assess which surfaces actively contribute to the contamination of the fuel. Both imaging spectroscopy and narrow-band crystal imaging were used to identify the location of He-like Co ions. The Te and ne of the Co is inferred by fitting the He-alpha lines and the near-by Li-like satellites. The experimental measurements and the challenges associated with the analysis will be discussed. Sandia Natl Lab is a multi-mission laboratory managed and operated by National Technology and Engineering Solutions of Sandia, LLC., a wholly owned subsidiary of Honeywell International, Inc., for the U.S. DOE NNSA under contract DE-NA-0003525.

Method of making highly sinterable lanthanum chromite powder

Science.gov (United States)

Richards, Von L.; Singhal, Subhash C.

1992-01-01

A highly sinterable powder consisting essentially of LaCrO.sub.3, containing from 5 weight % to 20 weight % of a chromite of dopant Ca, Sr, Co, Ba, or Mg and a coating of a chromate of dopant Ca, Sr, Co, Ba, or Mg; is made by (1) forming a solution of La, Cr, and dopant; (2) heating their solutions; (3) forming a combined solution having a desired ratio of La, Cr, and dopant and heating to reduce solvent; (4) forming a foamed mass under vacuum; (5) burning off organic components and forming a charred material; (6) grinding the charred material; (7) heating the char at from 590.degree. C. to 950 C. in inert gas containing up to 50,000 ppm O.sub.2 to provide high specific surface area particles; (8) adding that material to a mixture of a nitrate of Cr and dopant to form a slurry; (9) grinding the particles in the slurry; (10) freeze or spray drying the slurry to provide a coating of nitrates on the particles; and (11) heating the coated particles to convert the nitrate coating to a chromate coating and provide a highly sinterable material having a high specific surface area of over 7 m.sup.2 /g.

A survey of acceptor dopants for β-Ga2O3

Science.gov (United States)

Lyons, John L.

2018-05-01

With a wide band gap, high critical breakdown voltage and commercially available substrates, Ga2O3 is a promising material for next-generation power electronics. Like most wide-band-gap semiconductors, obtaining better control over its electrical conductivity is critically important, but has proven difficult to achieve. Although efficient p-type doping in Ga2O3 is not expected, since theory and experiment indicate the self-trapping of holes, the full development of this material will require a better understanding of acceptor dopants. Here the properties of group 2, group 5 and group 12 acceptor impurities in β-Ga2O3 are explored using hybrid density functional calculations. All impurities are found to exhibit acceptor transition levels above 1.3 eV. After examining formation energies as a function of chemical potential, Mg (followed closely by Be) is determined to be the most stable acceptor species.

Sintering of nickel catalysts. Effects of time, atmosphere, temperature, nickel-carrier interactions, and dopants

Energy Technology Data Exchange (ETDEWEB)

Sehested, Jens; Gelten, Johannes A.P.; Helveg, Stig [Haldor Topsoee A/S, Nymoellevej 55, DK-2800 Kgs. Lyngby (Denmark)

2006-08-01

Supported nickel catalysts are widely used in the steam-reforming process for industrial scale production of hydrogen and synthesis gas. This paper provides a study of sintering in nickel-based catalysts (Ni/Al{sub 2}O{sub 3} and Ni/MgAl{sub 2}O{sub 4}). Specifically the influence of time, temperature, atmosphere, nickel-carrier interactions and dopants on the rate of sintering is considered. To probe the sintering kinetics, all catalysts were analyzed by sulfur chemisorption to determine the Ni surface area. Furthermore selected samples were further analyzed using X-ray diffraction (XRD), mercury porosimetry, BET area measurements, and electron microscopy (EM). The observed sintering rates as a function of time, temperature, and P{sub H{sub 2}O}/P{sub H{sub 2}} ratio were consistent with recent model predictions [J. Sehested, J.A.P. Gelten, I.N. Remediakis, H. Bengaard, J.K. Norskov, J. Catal. 223 (2004) 432] over a broad range of environmental conditions. However, exposing the catalysts to severe sintering conditions the loss of nickel surface area is faster than model predictions and the deviation is attributed to a change in the sintering mechanism and nickel removal by nickel-carrier interactions. Surprisingly, alumina-supported Ni particles grow to sizes larger than the particle size of the carrier indicating that the pore diameter does not represent an upper limit for Ni particle growth. The effects of potassium promotion and sulfur poisoning on the rates of sintering were also investigated. No significant effects of the dopants were observed after ageing at ambient pressure. However, at high pressures of steam and hydrogen (31bar and H{sub 2}O:H{sub 2}=10:1) potassium promotion increased the sintering rate relative to that of the unpromoted catalyst. Sulfur also enhances the rate of sintering at high pressures, but the effect of sulfur is less than for potassium. (author)

Transient enhanced diffusion of dopants in preamorphized Si layers

International Nuclear Information System (INIS)

Claverie, A.; Bonafos, C.; Omri, M.; Mauduit, B. de; Ben Assayag, G.; Martinez, A.; Alquier, D.; Mathiot, D.

1997-01-01

Transient Enhanced Diffusion (TED) of dopants in Si is the consequence of the evolution, upon annealing, of a large supersaturation of Si self-interstitial atoms left after ion bombardment. In the case of amorphizing implants, this supersaturation is located just beneath the c/a interface and evolves through the nucleation and growth of End-Of-Range (EOR) defects. For this reason, the authors discuss here the relation between TED and EOR defects. Modelling of the behavior of these defects upon annealing allows one to understand why and how they affect dopant diffusion. This is possible through the development of the Ostwald ripening theory applied to extrinsic dislocation loops. This theory is shown to be readily able to quantitatively describe the evolution of the defect population (density, size) upon annealing and gives access to the variations of the mean supersaturation of Si self-interstitial atoms between the loops and responsible for TED. This initial supersaturation is, before annealing, at least 5 decades larger than the equilibrium value and exponentially decays with time upon annealing with activation energies that are the same than the ones observed for TED. It is shown that this time decay is precisely at the origin of the transient enhancement of boron diffusivity through the interstitial component of boron diffusion. Side experiments shed light on the effect of the proximity of a free surface on the thermal behavior of EOR defects and allow us to quantitatively describe the space and time evolutions of boron diffusivity upon annealing of preamorphized Si layers

Importance of doping, dopant distribution, and defects on electronic band structure alteration of metal oxide nanoparticles: Implications for reactive oxygen species

International Nuclear Information System (INIS)

Saleh, Navid B.; Milliron, Delia J.; Aich, Nirupam; Katz, Lynn E.; Liljestrand, Howard M.; Kirisits, Mary Jo

2016-01-01

Metal oxide nanoparticles (MONPs) are considered to have the potency to generate reactive oxygen species (ROS), one of the key mechanisms underlying nanotoxicity. However, the nanotoxicology literature demonstrates a lack of consensus on the dominant toxicity mechanism(s) for a particular MONP. Moreover, recent literature has studied the correlation between band structure of pristine MONPs to their ability to introduce ROS and thus has downplayed the ROS-mediated toxicological relevance of a number of such materials. On the other hand, material science can control the band structure of these materials to engineer their electronic and optical properties and thereby is constantly modulating the pristine electronic structure. Since band structure is the fundamental material property that controls ROS-producing ability, band tuning via introduction of dopants and defects needs careful consideration in toxicity assessments. This commentary critically evaluates the existing material science and nanotoxicity literature and identifies the gap in our understanding of the role of important crystal structure features (i.e., dopants and defects) on MONPs' electronic structure alteration as well as their ROS-generation capability. Furthermore, this commentary provides suggestions on characterization techniques to evaluate dopants and defects on the crystal structure and identifies research needs for advanced theoretical predictions of their electronic band structures and ROS-generation abilities. Correlation of electronic band structure and ROS will not only aid in better mechanistic assessment of nanotoxicity but will be impactful in designing and developing ROS-based applications ranging from water disinfection to next-generation antibiotics and even cancer therapeutics. - Highlights: • Metal oxide nanoparticles (MONPs) produce reactive oxygen species (ROS) • Band structure of pristine MONPs is different than those with dopants/defects • Dopants/defects modulate

Importance of doping, dopant distribution, and defects on electronic band structure alteration of metal oxide nanoparticles: Implications for reactive oxygen species

Energy Technology Data Exchange (ETDEWEB)

Saleh, Navid B., E-mail: navid.saleh@utexas.edu [Department of Civil, Architectural, and Environmental Engineering, University of Texas, Austin, TX 78712 (United States); Milliron, Delia J. [McKetta Department of Chemical Engineering, University of Texas, Austin, TX 78712 (United States); Aich, Nirupam [Department of Civil, Structural and Environmental Engineering, University at Buffalo, The State University of New York, Buffalo, NY, 14260 (United States); Katz, Lynn E.; Liljestrand, Howard M.; Kirisits, Mary Jo [Department of Civil, Architectural, and Environmental Engineering, University of Texas, Austin, TX 78712 (United States)

2016-10-15

Metal oxide nanoparticles (MONPs) are considered to have the potency to generate reactive oxygen species (ROS), one of the key mechanisms underlying nanotoxicity. However, the nanotoxicology literature demonstrates a lack of consensus on the dominant toxicity mechanism(s) for a particular MONP. Moreover, recent literature has studied the correlation between band structure of pristine MONPs to their ability to introduce ROS and thus has downplayed the ROS-mediated toxicological relevance of a number of such materials. On the other hand, material science can control the band structure of these materials to engineer their electronic and optical properties and thereby is constantly modulating the pristine electronic structure. Since band structure is the fundamental material property that controls ROS-producing ability, band tuning via introduction of dopants and defects needs careful consideration in toxicity assessments. This commentary critically evaluates the existing material science and nanotoxicity literature and identifies the gap in our understanding of the role of important crystal structure features (i.e., dopants and defects) on MONPs' electronic structure alteration as well as their ROS-generation capability. Furthermore, this commentary provides suggestions on characterization techniques to evaluate dopants and defects on the crystal structure and identifies research needs for advanced theoretical predictions of their electronic band structures and ROS-generation abilities. Correlation of electronic band structure and ROS will not only aid in better mechanistic assessment of nanotoxicity but will be impactful in designing and developing ROS-based applications ranging from water disinfection to next-generation antibiotics and even cancer therapeutics. - Highlights: • Metal oxide nanoparticles (MONPs) produce reactive oxygen species (ROS) • Band structure of pristine MONPs is different than those with dopants/defects • Dopants/defects modulate

Imaging Dirac-mass disorder from magnetic dopant atoms in the ferromagnetic topological insulator Crx(Bi0.1Sb0.9)2-xTe3.

Science.gov (United States)

Lee, Inhee; Kim, Chung Koo; Lee, Jinho; Billinge, Simon J L; Zhong, Ruidan; Schneeloch, John A; Liu, Tiansheng; Valla, Tonica; Tranquada, John M; Gu, Genda; Davis, J C Séamus

2015-02-03

To achieve and use the most exotic electronic phenomena predicted for the surface states of 3D topological insulators (TIs), it is necessary to open a "Dirac-mass gap" in their spectrum by breaking time-reversal symmetry. Use of magnetic dopant atoms to generate a ferromagnetic state is the most widely applied approach. However, it is unknown how the spatial arrangements of the magnetic dopant atoms influence the Dirac-mass gap at the atomic scale or, conversely, whether the ferromagnetic interactions between dopant atoms are influenced by the topological surface states. Here we image the locations of the magnetic (Cr) dopant atoms in the ferromagnetic TI Cr0.08(Bi0.1Sb0.9)1.92Te3. Simultaneous visualization of the Dirac-mass gap Δ(r) reveals its intense disorder, which we demonstrate is directly related to fluctuations in n(r), the Cr atom areal density in the termination layer. We find the relationship of surface-state Fermi wavevectors to the anisotropic structure of Δ(r) not inconsistent with predictions for surface ferromagnetism mediated by those states. Moreover, despite the intense Dirac-mass disorder, the anticipated relationship [Formula: see text] is confirmed throughout and exhibits an electron-dopant interaction energy J* = 145 meV·nm(2). These observations reveal how magnetic dopant atoms actually generate the TI mass gap locally and that, to achieve the novel physics expected of time-reversal symmetry breaking TI materials, control of the resulting Dirac-mass gap disorder will be essential.

Influence of dopant concentration on the electrical properties of the CdSe-PMMA nanocomposite

Energy Technology Data Exchange (ETDEWEB)

Kaur, Ramneek; Tripathi, S. K., E-mail: surya@pu.ac.in, E-mail: surya-tr@yahoo.com [Department of Physics, Center of Advanced Study in Physics, Panjab University, Chandigarh-160 014 (India)

2016-05-06

This paper reports the synthesis and electrical characterization of CdSe-PMMA nanocomposite. CdSe-PMMA nanocomposite has been prepared by ex-situ technique through chemical route. The influence of three different Ag doping concentrations on the electrical properties has been studied in the temperature range ∼ 303-353 K. Transmission electron micrograph reveals the spherical morphology of the CdSe nanoparticles and their proper dispersion in the PMMA matrix. The electrical conduction of the polymer nanocomposites is through thermally activated process with single activation energy. With Ag doping, initially the activation energy increases upto 0.2 % Ag doping concentration but with further increase in Ag concentration, it decreases. This behavior has been discussed on the basis of randomly oriented grain boundaries and defect states. Thus, the results indicate that the transport properties of the polymer nanocomposites can be tailored by controlled doping concentration.

Influence of dopant concentration on the electrical properties of the CdSe-PMMA nanocomposite

International Nuclear Information System (INIS)

Kaur, Ramneek; Tripathi, S. K.

2016-01-01

This paper reports the synthesis and electrical characterization of CdSe-PMMA nanocomposite. CdSe-PMMA nanocomposite has been prepared by ex-situ technique through chemical route. The influence of three different Ag doping concentrations on the electrical properties has been studied in the temperature range ∼ 303-353 K. Transmission electron micrograph reveals the spherical morphology of the CdSe nanoparticles and their proper dispersion in the PMMA matrix. The electrical conduction of the polymer nanocomposites is through thermally activated process with single activation energy. With Ag doping, initially the activation energy increases upto 0.2 % Ag doping concentration but with further increase in Ag concentration, it decreases. This behavior has been discussed on the basis of randomly oriented grain boundaries and defect states. Thus, the results indicate that the transport properties of the polymer nanocomposites can be tailored by controlled doping concentration.

What is the origin of concentration quenching of Cu{sup +} luminescence in glass?

Energy Technology Data Exchange (ETDEWEB)

Jiménez, José A., E-mail: jimenez.materials@gmail.com

2016-10-01

Monovalent copper-doped luminescent glasses are attractive materials for white light-emitting devices, photonic waveguides, and solar spectral conversion in photovoltaic cells. However, the occurrence of concentration quenching in such is not fully understood at present. In this work, calcium-phosphate glasses with high concentrations of luminescent Cu{sup +} ions have been prepared by a simple melt-quench method via CuO and SnO co-doping. The aim is to elucidate the origin of concentration quenching of Cu{sup +} light emission. A spectroscopic characterization was carried out by optical absorption and photoluminescence (PL) spectroscopy including emission decay dynamics. The concentrations of both CuO and SnO dopants were varied as 5, 10 and 15 mol%. Monovalent copper content is estimated in the CuO/SnO-containing glasses following the assessment of the concentration dependence of Cu{sup 2+} absorption in the visible for CuO singly-doped glasses. Contrary to the conventionally acknowledged direct Cu{sup +}→Cu{sup 2+} transfer, the data supports a Cu{sup +}–Cu{sup +} energy migration channel at the origin of the PL quenching.

A new method to characterize dopant profiles in NMOSFETs using conventional transmission electron microscopy

International Nuclear Information System (INIS)

Kawamura, Kazuo; Ikeda, Kazuto; Terauchi, Masami

2004-01-01

We have developed a new method using conventional transmission electron microscopy (TEM) to obtain two dimensional dopant profiles in silicon and applied it to 40 nm-gate-length N + /p metal oxide semiconductor field effect transistors (MOSFETs). The results are consistent with those of selective-chemically etched samples observed by TEM. This method, using focused ion beam (FIB) sample preparation and conventional TEM, has the great advantage of simple sample preparation and high spatial resolution compared to other characterization methods, such as atomic capacitance microscopy, spreading resistance microscopy, and TEM combined with selective chemical etching. This indicates that this method can be applicable to the analysis of FETs at the 65 nm or smaller node

A theoretical study of dopant atom detection and probe behavior in STEM

Science.gov (United States)

Mittal, Anudha

Very detailed information about the atomic and electronic structure of materials can be obtained via atomic-scale resolution scanning transmission electron microscopy (STEM). These experiments reach the limits of current microscopes, which means that optimal experimental design is a key ingredient in success. The step following experiment, extraction of information from experimental data is also complex. Comprehension of experimental data depends on comparison with simulated data and on fundamental understanding of aspects of scattering behavior. The research projects discussed in this thesis are formulated within three large concepts. 1. Usage of simulation to suggest experimental technique for observation of a particular structural feature.. Two specific structural features are explored. One is the characterization of a substitutional dopant atom in a crystal. Annular dark field scanning transmission electron microscope (ADF-STEM) images allow detection of individual dopant atoms in a crystal based on contrast between intensities of doped and non-doped column in the image. The magnitude of the said contrast is heavily influenced by specimen and microscope parameters. Analysis of multislice-based simulations of ADF-STEM images of crystals doped with one substitutional dopant atom for a wide range of crystal thicknesses, types and locations of dopant atom inside the crystal, and crystals with different atoms revealed trends and non-intuitive behaviors in visibility of the dopant atom. The results provide practical guidelines for the optimal experimental setup regarding both the microscope and specimen conditions in order to characterize the presence and location of a dopant atom. Furthermore, the simulations help in recognizing the cases where detecting a single dopant atom via ADF-STEM imaging is not possible. The second is a more specific case of detecting intrinsic twist in MoS2 nanotubes. Objective molecular dynamics simulations coupled with a density

Imaging of dopant distribution in optical fibers with an orthogonal TOF SIMS

Czech Academy of Sciences Publication Activity Database

Lorinčík, Jan; Kašík, Ivan; Vaniš, Jan; Sedláček, L.; Dluhoš, J.

2014-01-01

Roč. 46, č. 1 (2014), s. 238-240 ISSN 0142-2421. [19th International Conference on Secondary Ion Mass Spectrometry ( SIMS ). Jeju, 29.09.2013-04.10.2013] Grant - others:GA AV ČR(CZ) M100761202 Institutional support: RVO:67985882 Keywords : TOF SIMS * Optical fibers * Dopant Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering Impact factor: 1.245, year: 2014

Self Consistent Ambipolar Transport and High Frequency Oscillatory Transient in Graphene Electronics

Science.gov (United States)

2015-08-17

scholarships or fellowships for further studies in science, mathematics, engineering or technology fields: Student Metrics This section only applies...whereas strong Coulomb scattering arising from the charged dopants would offset the effect. In graphene, the absence of an energy gap guarantees carriers...carrier dynamics, as long as the Coulomb scattering (dopant concentration) can be kept weak, as shown in Ref. 68 and later on in this analysis. Note

Photosensitive self-assembling materials as functional dopants for organic photovoltaic cells

Czech Academy of Sciences Publication Activity Database

Bubnov, Alexej; Iwan, A.; Cigl, Martin; Boharewicz, B.; Tazbir, I.; Wójcik, K.; Sikora, A.; Hamplová, Věra

2016-01-01

Roč. 6, č. 14 (2016), s. 11577-11590 ISSN 2046-2069 R&D Projects: GA MŠk 7AMB13PL041; GA MŠk(CZ) LD14007; GA ČR GA15-02843S Grant - others:EU - ICT(XE) COST Action IC1208 Institutional support: RVO:68378271 Keywords : self-assembling materials * functional dopants * organic photovoltaic cells * azo group * liquid crystal Subject RIV: JI - Composite Materials Impact factor: 3.108, year: 2016

Study of the chlorine as dopant in synthesized polymers by plasma; Estudio del cloro como dopante en polimeros sintetizados por plasma

Energy Technology Data Exchange (ETDEWEB)

Vasquez, M.; Cruz, G.; Olayo, M.G. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico); Timoshina, T. [ESIQIE, IPN, 07738 Mexico D.F. (Mexico); Morales, J.; Olayo, R. [UAM-I, 09340 Mexico D.F. (Mexico)

2003-07-01

In the search of new and better dopants for semiconductor polymers, in this work the synthesis by plasma and the characterization of two doped polymers with chlorine, Pyrrole (PPy) and Thiophene (PTh) is presented. The characterization of the polymers it was carried out by FT-lR, it shows the C-Cl vibration that it is confirmed with the X-ray photoelectron spectroscopy technique (XPS). The elementary analysis shows a greater quantity of Cl in the PTh-CI compared with PPy-CI. However, this effect is not reflected in the electric conductivity since the PTh-Cl presents a lightly greater conductivity than the PPy-CI. SEM shows a formed structure of small agglomerated spheres of different size. (Author)

Control of oxygen vacancies and Ce+3 concentrations in doped ceria nanoparticles via the selection of lanthanide element

International Nuclear Information System (INIS)

Shehata, N.; Meehan, K.; Hudait, M.; Jain, N.

2012-01-01

The effect of lanthanides that have positive association energies with oxygen vacancies, such as samarium and neodymium, and the elements with negative association energies, such as holmium and erbium, on ionization state of cerium and, consequentially, the oxygen vacancy concentration in doped ceria nanoparticles are investigated in this article. Structural and optical characterizations of the doped and undoped ceria nanoparticles, synthesized using chemical precipitation, are carried out using transmission electron microscopy, X-ray diffractometry, optical absorption spectroscopy, and fluorescence spectroscopy. It is deduced that the negative association energy dopants decrease the conversion of Ce +4 into Ce +3 and, hence, scavenge the oxygen vacancies, evidenced by the observed increase in the allowed direct bandgap, decrease in the integrated fluorescence intensity, and increased the size of doped nanoparticles. The opposite trends are obtained when the positive association dopants are used. It is concluded that the determining factor as to whether a lanthanide dopant in ceria acts as a generator or scavenger of oxygen vacancies in ceria nanoparticles is the sign of the association energy between the element and the oxygen vacancies. The ability to tailor the ionization state of cerium and the oxygen vacancy concentration in ceria has applications in a broad range of fields, which include catalysis, biomedicine, electronics, and environmental sensing.

Investigation of the ionization mechanism of polycyclic aromatic hydrocarbons using an ethanol/bromobenzene/chlorobenzene/anisole mixture as a dopant in liquid chromatography/atmospheric pressure photoionization mass spectrometry

KAUST Repository

Amad, Maan H.

2012-09-23

RATIONALE An ethanol-based multicomponent dopant consisting of ethanol/chlorobenzene/bromobenzene/anisole (98.975:0.1:0.9:0.025, v/v/v/v) has been used as a dopant for atmospheric pressure photoionization (APPI) of polycyclic aromatic hydrocarbons (PAHs). In this study the mechanism of ionization of PAHs assisted by the ethanol-based multicomponent dopant is investigated. METHODS The reactant background cluster ions of the ethanol-based multicomponent dopant observed in the positive ion APPI were studied. These studies were performed to investigate the mechanism behind the generation of a molecular radical cation (M +•) for PAHs by APPI assisted by the ethanol-based multicomponent dopant. Full scan and MS/MS analyses were conducted using an LTQ Orbitrap mass spectrometer. The effect of acidification of the mobile phase on the dopant cluster ion formation was also investigated. RESULTS With the ethanol-based multicomponent dopant, a single type of molecular radical cation M +• was observed for the studied PAHs. The characteristic ion signal of the multicomponent dopant mixture consisted of mainly anisole photoions at m/z 108.05697 and its adduct ions at m/z 124.05188 and 164.07061. The anisole ion response at m/z 108.05697 was stable in the presence of acetonitrile, methanol, water and 0.1% formic acid mobile phase composition. CONCLUSIONS The abundance formation of anisole photoions shows the universality of this multicomponent dopant in ionizing compounds with ionization energy ranging from 7.1-8.2 eV. Since the ionization energy of anisole is 8.2 eV and is lower than those of chlorobenzene (9.07 eV) and bromobenzene (9.0 eV), the mechanism of formation of anisole photoions even with its very minute amounts was not only governed by its photoionization by the krypton lamp photon energy (10.0 eV and 10.6 eV), but also by charge transfer from bromobenzene and chlorobenzene radical cations. PAH molecules were mainly ionized by charge transfer reaction from

Investigation of the ionization mechanism of polycyclic aromatic hydrocarbons using an ethanol/bromobenzene/chlorobenzene/anisole mixture as a dopant in liquid chromatography/atmospheric pressure photoionization mass spectrometry

KAUST Repository

Amad, Maan H.; Sioud, Salim

2012-01-01

RATIONALE An ethanol-based multicomponent dopant consisting of ethanol/chlorobenzene/bromobenzene/anisole (98.975:0.1:0.9:0.025, v/v/v/v) has been used as a dopant for atmospheric pressure photoionization (APPI) of polycyclic aromatic hydrocarbons (PAHs). In this study the mechanism of ionization of PAHs assisted by the ethanol-based multicomponent dopant is investigated. METHODS The reactant background cluster ions of the ethanol-based multicomponent dopant observed in the positive ion APPI were studied. These studies were performed to investigate the mechanism behind the generation of a molecular radical cation (M +•) for PAHs by APPI assisted by the ethanol-based multicomponent dopant. Full scan and MS/MS analyses were conducted using an LTQ Orbitrap mass spectrometer. The effect of acidification of the mobile phase on the dopant cluster ion formation was also investigated. RESULTS With the ethanol-based multicomponent dopant, a single type of molecular radical cation M +• was observed for the studied PAHs. The characteristic ion signal of the multicomponent dopant mixture consisted of mainly anisole photoions at m/z 108.05697 and its adduct ions at m/z 124.05188 and 164.07061. The anisole ion response at m/z 108.05697 was stable in the presence of acetonitrile, methanol, water and 0.1% formic acid mobile phase composition. CONCLUSIONS The abundance formation of anisole photoions shows the universality of this multicomponent dopant in ionizing compounds with ionization energy ranging from 7.1-8.2 eV. Since the ionization energy of anisole is 8.2 eV and is lower than those of chlorobenzene (9.07 eV) and bromobenzene (9.0 eV), the mechanism of formation of anisole photoions even with its very minute amounts was not only governed by its photoionization by the krypton lamp photon energy (10.0 eV and 10.6 eV), but also by charge transfer from bromobenzene and chlorobenzene radical cations. PAH molecules were mainly ionized by charge transfer reaction from

Origin and Quenching of Novel ultraviolet and blue emission in NdGaO3: Concept of Super-Hydrogenic Dopants.

Science.gov (United States)

Ghosh, Siddhartha; Saha, Surajit; Liu, Zhiqi; Motapothula, M; Patra, Abhijeet; Yakovlev, Nikolai; Cai, Yao; Prakash, Saurav; Huang, Xiao Hu; Tay, Chuan Beng; Cong, Chun Xiao; Bhatt, Thirumaleshwara; Dolmanan, Surani B; Chen, Jianqiang; Lü, Weiming; Huang, Zhen; Tripathy, Sudhiranjan; Chua, Soo Jin; Yu, Ting; Asta, Mark; Ariando, A; Venkatesan, T

2016-11-03

In this study we report the existence of novel ultraviolet (UV) and blue emission in rare-earth based perovskite NdGaO 3 (NGO) and the systematic quench of the NGO photoluminescence (PL) by Ce doping. Study of room temperature PL was performed in both single-crystal and polycrystalline NGO (substrates and pellets) respectively. Several NGO pellets were prepared with varying Ce concentration and their room temperature PL was studied using 325 nm laser. It was found that the PL intensity shows a systematic quench with increasing Ce concentration. XPS measurements indicated that nearly 50% of Ce atoms are in the 4+ state. The PL quench was attributed to the novel concept of super hydrogenic dopant (SHD)", where each Ce 4+ ion contributes an electron which forms a super hydrogenic atom with an enhanced Bohr radius, due to the large dielectric constant of the host. Based on the critical Ce concentration for complete quenching this SHD radius was estimated to be within a range of 0.85 nm and 1.15 nm whereas the predicted theoretical value of SHD radius for NdGaO3 is ~1.01 nm.

Effects of Lithium Dopant on Size and Morphology of Magnesium Oxide Nano powders

International Nuclear Information System (INIS)

Mohd Sufri Mastuli; Siti Nur Hazlinda Hasbu; Noraziahwati Ibrahim; Mohd Azizi Nawawi; Mohd Sufri Mastuli

2014-01-01

Lithium doped of magnesium oxide powders have been synthesized using the sol-gel method with magnesium acetate tetrahydrate, oxalic acid dihydrate and lithium acetate dihydrate used as the starting materials. The dried sol-gel products were calcined at 950 degree Celsius for 36 h to form the Li doped-MgO samples. The calcined samples were characterized using X-Ray diffraction (XRD) and field emission scanning electron microscopy (FESEM). The present work is investigated the effect of lithium ion on the band gap energy of studied samples. The band gap energies were obtained from a Tauc plot that drawn based on absorption edge of each sample that measured using a UV-Vis spectrophotometer. It is found that the doped and undoped MgO samples showed a slightly different in their band gap energies. The lithium ion that present in the MgO as a dopant affects the crystallite size and morphology of the final products. Our study shows that the lithium dopant can modified optical properties of the metal oxide which to be beneficial in some industrial applications. (author)

Spectroscopic XPEEM of highly conductive SI-doped GaN wires

Energy Technology Data Exchange (ETDEWEB)

Renault, O., E-mail: olivier.renault@cea.fr [Univ. Grenoble Alpes, F-38000 Grenoble (France); CEA, LETI, MINATEC Campus, F-38054 Grenoble (France); Morin, J. [Univ. Grenoble Alpes, F-38000 Grenoble (France); CEA, LETI, MINATEC Campus, F-38054 Grenoble (France); Tchoulfian, P. [Univ. Grenoble Alpes, F-38000 Grenoble (France); CEA, LETI, MINATEC Campus, F-38054 Grenoble (France); CNRS, Inst. NEEL, F-38042 Grenoble (France); Chevalier, N. [Univ. Grenoble Alpes, F-38000 Grenoble (France); CEA, LETI, MINATEC Campus, F-38054 Grenoble (France); Feyer, V. [Peter Grünberg Institute (PGI-6) and JARA-FIT, Research Center Jülich, D-52425 Jülich (Germany); Pernot, J. [Univ. Grenoble Alpes, F-38000 Grenoble (France); CNRS, Inst. NEEL, F-38042 Grenoble (France); Institut Universitaire de France, F-75005 Paris (France); Schneider, C.M. [Peter Grünberg Institute (PGI-6) and JARA-FIT, Research Center Jülich, D-52425 Jülich (Germany)

2015-12-15

Using soft X-ray photoelectron emission microscopy (XPEEM), complemented by scanning Auger microscopy (SAM) and scanning capacitance microscopy, we have quantitatively studied the incorporation of silicon and band bending at the surface (m-facet) of an individual, highly conductive Si-doped GaN micro-wires (Tchoulfian et al., Applied Physics Letters 102 (12), 2013). Electrically active n-dopants Si atoms in Ga interstitial sites are detected as nitride bonding states in the high-resolution Si2p core level spectra, and represent only a small fraction (<10%) of the overall Si surface concentration measured by SAM. The derived carrier concentration of 2×10{sup 21} at cm{sup −3} is in reasonable agreement with electrical measurements. A consistent surface band bending of ~1 eV is directly evidenced by surface photo-voltage measurements. Such an approach combining different surface-sensitive microscopies is of interest for studying other heavily doped semiconducting wires. - Highlights: • XPEEM analysis of state-of-the-art, heavily doped GaN wires with insights on the issue of the origin of the increased conductivity. • Combined microscopic approach with Scanning Auger microscopy and X-ray Photoeletron Emission Microscopy, to quantity the electrically active Si-dopants in GaN. • The determined concentration is found in reasonable agreement with the one derived from bulk electrical measurements. • The proposed method is of interest for studying the electronics and chemistry of doping in other heavily doped semiconducting wires.

Effect of anionic dopants on thickness, morphology and electrical properties of polypyrrole ultra-thin films prepared by in situ chemical polymerization

Energy Technology Data Exchange (ETDEWEB)

Mahmoodian, Mehrnoosh [Dep. of Polymer Engineering, Nanostructured Materials Research Center, Sahand University of Technology, Tabriz 51335-1996 (Iran, Islamic Republic of); Pourabbas, Behzad, E-mail: pourabas@sut.ac.ir [Dep. of Polymer Engineering, Nanostructured Materials Research Center, Sahand University of Technology, Tabriz 51335-1996 (Iran, Islamic Republic of); Mohajerzadeh, Shams [Nano-Electronics and Thin Film Lab, School of Electrical and Computer Engineering, University of Tehran, P.O. Box 14395/515, Tehran (Iran, Islamic Republic of)

2015-05-29

The effect of different dopant anions on deposition and characteristics of polypyrrole (PPy) thin film has been studied in this work. Ultra-thin films of conducting PPy were deposited on insulating surfaces of glass and oxidized silicon wafer by in situ chemical polymerization in the presence of different anionic dopants including sodium dodecylbenzenesulfonate, sodium dodecyl sulfate, α-naphthalene sulfonic acid, anthraquinone-2-sulfonic acid sodium salt monohydrate/5-sulfosalicylic acid dehydrate, and camphor sulfonic acid. Hydrophilic/hydrophobic properties and morphology of the self-assembled monolayer of N-(3-trimethoxysilylpropyl)pyrrole, the surface modifying agent in this work, and PPy thin films were characterized before and after deposition by contact angle measurements, field emission scanning electron microscopy, and atomic force microscopy. Chemical structure, thickness, and conductivity of the thin films were also studied by attenuated total reflectance Fourier transform infrared spectrometer, ellipsometry, and four-point probe measurements. The results showed deposition of thin films of conducting PPy with comparable thickness in the range of 6-31 nm and different morphologies, uniformity, and smoothness with average roughness in the range of 0.3-6 nm and relatively high range of conductivity on the modified surfaces. - Highlights: • Conducting thin films of polypyrrole were deposited on glass and SiO{sub 2} substrates. • Surface modification using pyrrole-silane was employed prior to polymerization. • Films as thin as ≈ 7 nm were deposited using different surfactant/counter ions. • Chemistry of the counter ion affects thickness, conductivity and morphology. • Lower thickness/higher conductivity were obtained by structurally flexible dopants.

Pyrolysis synthesis of Zn{sub 2}SiO{sub 4}:Mn{sup 2+} phosphors – effect of fuel, flux and co-dopants

Energy Technology Data Exchange (ETDEWEB)

Sivakumar, V.; Lakshmanan, Arunachalam, E-mail: arunachalamlakshmanan@yahoo.com

2014-01-15

Green emitting α-Zn{sub 2}SiO{sub 4}:Mn{sup 2+} phosphors were made by pyrolysis route at 600 °C followed by sintering at a moderate temperature of 1000 °C for 1 h duration. The effects of different fuels (urea, citric acid, polyethylene glycol and glycine), flux materials (H{sub 3}BO{sub 3}, NH{sub 4}Cl, NH{sub 4}F, NH{sub 4}Br, BaCl{sub 2}, BaBr{sub 2}, CaF{sub 2} and BaF{sub 2}), divalant co-dopants (Ca{sup 2+}, Ba{sup 2+}, Mg{sup 2+} and Sr{sup 2+}), trivalent co-dopants (Al{sup 3+}, Y{sup 3+} and Gd{sup 3+}) and sintering temperature (800–1000 °C) on the photoluminescence (PL) efficiency of Zn{sub 2}SiO{sub 4}:Mn{sup 2+} were studied. Among the fuels, urea and among the flux, H{sub 3}BO{sub 3} gave a maximum broad band green PL emission peak at 525 nm on excitation at 254 nm. Divalent co-dopants improved the PL intensity much more than the trivalent co-dopants used. Highest PL efficiency was observed with Sr{sup 2+} co-doped Zn{sub 2}SiO{sub 4}:Mn{sup 2+} sintered at 1000 °C in reducing atmosphere which was 20% higher than that of the commercial Zn{sub 2}SiO{sub 4}:Mn{sup 2+}. The formation of a single crystalline phase of willemite structure in the α-Zn{sub 2}SiO{sub 4}:Mn{sup 2+} samples synthesized was confirmed by powder XRD measurements. -- Highlights: • Zn{sub 2}SiO{sub 4}:Mn{sup 2+} green phosphors were made by pyrolysis route. • Effect of fuel, flux and co dopant on PL intensity. • Enhancement in luminescence with divalent co-dopants, notably Sr. • PL efficiency 20% higher than that of the commercial phosphor. • XRD confirm single phase willemite structure of Zn{sub 2}SiO{sub 4}:Mn{sup 2+}.

Thermodynamic modelling of fast dopant diffusion in Si

Science.gov (United States)

Saltas, V.; Chroneos, A.; Vallianatos, F.

2018-04-01

In the present study, nickel and copper fast diffusion in silicon is investigated in the framework of the cBΩ thermodynamic model, which connects point defect parameters with the bulk elastic and expansion properties. All the calculated point defect thermodynamic properties (activation Gibbs free energy, activation enthalpy, activation entropy, and activation volume) exhibit temperature dependence due to the non-linear anharmonic behavior of the isothermal bulk modulus of Si. Calculated activation enthalpies (0.15-0.16 eV for Ni and 0.17-0.19 eV for Cu) are in agreement with the reported experimental results. Small values of calculated activation volumes for both dopants (˜4% of the mean atomic volume) are consistent with the interstitial diffusion of Ni and Cu in Si.

Synthesis of highly luminescent Mn:ZnSe/ZnS nanocrystals in aqueous media

International Nuclear Information System (INIS)

Fang Zheng; Wu Ping; Zhong Xinhua; Yang Yongji

2010-01-01

High-quality water-dispersible Mn 2+ -doped ZnSe core/ZnS shell (Mn:ZnSe/ZnS) nanocrystals have been synthesized directly in aqueous media. Overcoating a high bandgap ZnS shell around the Mn:ZnSe cores can bring forward an efficient energy transfer from the ZnSe host nanocrystals to the dopant Mn. The quantum yields of the dopant Mn photoluminescence in the as-prepared water-soluble Mn:ZnSe/ZnS core/shell nanocrystals can be up to 35 ± 5%. The optical features and structure of the obtained Mn:ZnSe/ZnS core/shell nanocrystals have been characterized by UV-vis, PL spectroscopy, TEM, XRD and ICP elementary analysis. The influences of various experimental variables, including the Mn concentration, the Se/Zn molar ratio as well as the kind and amount of capping ligand used in the core production and shell deposition process, on the luminescent properties of the obtained Mn:ZnSe/ZnS nanocrystals have been systematically investigated.

Determination of the dopant weight fraction in polyaniline films using a quartz-crystal microbalance

Czech Academy of Sciences Publication Activity Database

Ayad, M. M.; Zaki, E. A.; Stejskal, Jaroslav

2007-01-01

Roč. 515, č. 23 (2007), s. 8381-8385 ISSN 0040-6090 R&D Projects: GA AV ČR IAA4050313 Institutional research plan: CEZ:AV0Z40500505 Keywords : dopant weight fraction * polyaniline * polyaniline film Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.693, year: 2007

Improving stability of photoluminescence of ZnSe thin films grown by molecular beam epitaxy by incorporating Cl dopant

International Nuclear Information System (INIS)

Wang, J. S.; Shen, J. L.; Chen, W. J.; Tsai, Y. H.; Wang, H. H.; Yang, C. S.; Chen, R. H.; Tsai, C. D.

2011-01-01

This investigation studies the effect of chlorine (Cl) dopant in ZnSe thin films that were grown by molecular beam epitaxy on their photoluminescence (PL) and the stability thereof. Free excitonic emission was observed at room-temperature in the Cl-doped sample. Photon irradiation with a wavelength of 404 nm and a power density of 9.1 W/cm 2 has a much stronger effect on PL degradation than does thermal heating to a temperature of 150 deg. C. Additionally, this study shows that the generation of nonradiative centers by both photon irradiation and thermal heating can be greatly inhibited by incorporating Cl dopant.

In silico evaluation of highly efficient organic light-emitting materials

Science.gov (United States)

Kwak, H. Shaun; Giesen, David J.; Hughes, Thomas F.; Goldberg, Alexander; Cao, Yixiang; Gavartin, Jacob; Dixon, Steve; Halls, Mathew D.

2016-09-01

Design and development of highly efficient organic and organometallic dopants is one of the central challenges in the organic light-emitting diodes (OLEDs) technology. Recent advances in the computational materials science have made it possible to apply computer-aided evaluation and screening framework directly to the design space of organic lightemitting diodes (OLEDs). In this work, we will showcase two major components of the latest in silico framework for development of organometallic phosphorescent dopants - (1) rapid screening of dopants by machine-learned quantum mechanical models and (2) phosphorescence lifetime predictions with spin-orbit coupled calculations (SOC-TDDFT). The combined work of virtual screening and evaluation would significantly widen the design space for highly efficient phosphorescent dopants with unbiased measures to evaluate performance of the materials from first principles.

Optical acetone vapor sensors based on chiral nematic liquid crystals and reactive chiral dopants

NARCIS (Netherlands)

Cachelin, P.; Green, J.P.; Peijs, T.; Heeney, M.; Bastiaansen, C.W.M.

2016-01-01

Accurate monitoring of exposure to organic vapors, such as acetone, is an important part of maintaining a safe working environment and adhering to long- and short-term exposure limits. Here, a novel acetone vapor detection system is described based on the use of a reactive chiral dopant in a nematic

Characterization of high concentration dust generator

International Nuclear Information System (INIS)

Shimura, Toichiro; Yokochi, Akira

1999-01-01

This paper describes the development of fluidized bed type high concentration dust generator that keeps for long period dust concentration range of about 10 mg/m 3 for the study of working place monitoring system and evaluation of respirator. The generator is keeping constant powder in fluidized bed for keeping the dust concentration. It is necessary to keep constant feeding rate of powder in order to keep the quantity of dust in the fluidized bed. Our generator enables to obtain constant feeding rate by a screw feeder and by using mixed powder with fluidising particles (glass beads) before feeding. The generator produces high concentration dust of 11.3 mg/m 3 ± 1.0 mg/m 3 for about 5 hours and keeps the dust size 4.2-4.6 μm in mass median aerodynamic diameter with reasonable reproducibility. (author)

CaSO4:DY,Mn: A new and highly sensitive thermoluminescence phosphor for versatile dosimetry

Science.gov (United States)

Bahl, Shaila; Lochab, S. P.; Kumar, Pratik

2016-02-01

With the advent of newer techniques for dose reduction coupled with the development of more sensitive detectors, the radiation doses in radiological medical investigation are decreasing. Nevertheless, keeping the tenet in mind that all radiation doses could entail risk, there is a need to develop more sensitive dosimeters capable of measuring low doses. This paper gives the account of the development of a new and sensitive phosphor CaSO4:Dy,Mn and its characterization. The standard production procedure based on the recrystallization method was used to prepare CaSO4:Dy,Mn. The Thermoluminescence (TL) studies were carried out by exposing it with gamma radiation (Cs-137) from 10 μGy to 100 Gy. The theoretical studies to determine the number of peaks and kinetic parameters related to the TL glow peaks in CaSO4:Dy,Mn was performed using the Computerized Glow Curve Deconvolution (CGCD) method. Experiments were performed to determine optimum concentration of the dopants Dysprosium (Dy) and Mangnese (Mn) in the host CaSO4 so that maximum sensitivity of the phosphor may be achieved. The optimum dopant concentration turned out to be 0.1 mol%. As there were two dopants Dy and Mn their relative ratio were varied in steps of 0.025 keeping the concentration of total dopant (Dy and Mn) 0.1 mol% always. The maximum TL intensity was seen in the CaSO4:Dy(0.025),Mn(0.075) combination. The TL sensitivity of this phosphor was found to be about 2 and 1.8 times higher than that of popular phosphor CaSO4:Dy and LiF:Mg,Cu,P (TLD-700H) respectively. This new phosphor CaSO4:Dy,Mn showed fading of 11% which is similar to that of the standard phosphor CaSO4:Dy. The paper concludes that the new, highly sensitive TL phosphor CaSO4:Dy,Mn has shown higher sensitivity and hence the potential to replace commonly used CaSO4:Dy.

High Temperature Thermoelectric Properties of ZnO Based Materials

DEFF Research Database (Denmark)

Han, Li

of the dopants and dopant concentrations, a large power factor was obtainable. The sample with the composition of Zn0.9Cd0.1Sc0.01O obtained the highest zT ∼0.3 @1173 K, ~0.24 @1073K, and a good average zT which is better than the state-of-the-art n-type thermoelectric oxide materials. Meanwhile, Sc-doped Zn......This thesis investigated the high temperature thermoelectric properties of ZnO based materials. The investigation first focused on the doping mechanisms of Al-doped ZnO, and then the influence of spark plasma sintering conditions on the thermoelectric properties of Al, Ga-dually doped Zn......O. Following that, the nanostructuring effect for Al-doped ZnO was systematically investigated using samples with different microstructure morphologies. At last, the newly developed ZnCdO materials with superior thermoelectric properties and thermal stability were introduced as promising substitutions...

Dopant induced variations in microstructure and optical properties of CeO2 nanoparticles

International Nuclear Information System (INIS)

Mohanty, Bhaskar Chandra; Lee, Jong Won; Yeon, Deuk-Ho; Jo, Yeon-Hwa; Kim, Jong Hak; Cho, Yong Soo

2011-01-01

Research highlights: → Dopant (Zr 4+ , La 3+ , and Ca 2+ ) induced phase stability, and changes in microstructure and optical properties of CeO 2 nanoparticles have been studied. → The nanoparticles were prepared by hydrothermal synthesis of nitrate solutions. → The results show modification of the unit cell parameter by -0.39, +0.83 and +0.16% for doping of 20% Zr 4+ , La 3+ , and Ca 2+ , respectively. → For each batch prepared, nanoparticles with a narrow size distribution of 5-15 nm have been obtained. These particles are single crystals mostly having polygonal two-dimensional projections. → UV-visible spectra of doped particles exhibit shift of the absorption edge and absorption peak with respect to those of the undoped ones and has been attributed to compensation of Ce 3+ and decreasing crystallite size as result of doping. -- Abstract: Nanocrystalline CeO 2 particles doped in the range of 0-20% of Ca 2+ , La 3+ , and Zr 4+ have been prepared from hydrothermal synthesis of nitrate solutions at 200 o C and the influences of the dopants on microstructure and optical properties of the nanoparticles have been investigated. The unit cell parameter is found to be modified by -0.39, +0.83 and +0.16% for doping of 20% Zr 4+ , La 3+ , and Ca 2+ , respectively. For each batch prepared, nanoparticles with a narrow size distribution of 5-15 nm have been obtained. A high-resolution transmission electron microscopy investigation reveals that these particles are single crystals mostly having hexagonal, square or circular two-dimensional projections. UV-visible spectra of doped powders exhibit shift of the absorption edge and absorption peak with respect to those of the undoped CeO 2 particles and has been attributed to compensation of Ce 3+ and decreasing crystallite size as result of doping.

Influence of indium concentration and substrate temperature on the physical characteristics of chemically sprayed ZnO:In thin films deposited from zinc pentanedionate and indium sulfate

International Nuclear Information System (INIS)

Castaneda, L; Morales-Saavedra, O G; Cheang-Wong, J C; Acosta, D R; Banuelos, J G; Maldonado, A; Olvera, M de la L

2006-01-01

Chemically sprayed indium-doped zinc oxide thin films (ZnO:In) were deposited on glass substrates starting from zinc pentanedionate and indium sulfate. The influence of both the dopant concentration in the starting solution and the substrate temperature on the transport, morphology, composition, linear and nonlinear optical (NLO) properties of the ZnO:In thin films were studied. The structure of all the ZnO:In thin films was polycrystalline, and variation in the preferential growth with the indium content in the solution was observed: from an initial (002) growth in films with low In content, switching to a predominance of (101) planes for intermediate dopant regime, and finally turning to a (100) growth for heavily doped films. The crystallite size was found to decrease with doping concentration and range from 36 to 23 nm. The film composition and the dopant concentration were determined by Rutherford backscattering spectrometry; these results showed that the films are almost stoichiometric ZnO. The optimum deposition conditions leading to conductive and transparent ZnO:In thin films were also found. In this way a resistivity of 4 x 10 -3 Ω cm and an average transmittance in the visible spectra of 85%, with a (101) preferential growth, were obtained in optimized ZnO:In thin films

Dopant-Modulating Mechanism of Lithium Adsorption and Diffusion at the Graphene /Li2S Interface

Science.gov (United States)

Guo, Lichao; Li, Jiajun; Wang, Huayu; Zhao, Naiqin; Shi, Chunsheng; Ma, Liying; He, Chunnian; He, Fang; Liu, Enzuo

2018-02-01

Graphene modification is one of the most effective routes to enhance the electrochemical properties of the transition-metal sulfide anode for Li-ion batteries and the Li2S cathode for Li-S batteries. Boron, nitrogen, oxygen, phosphorus, and sulfur doping greatly affect the electrochemical properties of Li2S /graphene . Here, we investigate the interfacial binding energy, lithium adsorption energy, interface diffusion barrier, and electronic structure by first-principles calculations to unveil the diverse effects of different dopants during interfacial lithiation reactions. The interfacial lithium storage follows the pseudocapacitylike mechanism with intercalation character. Two different mechanisms are revealed to enhance the interfacial lithium adsorption and diffusion, which are the electron-deficiency host doping and the vacancylike structure evolutions with bond breaking. The synergistic effect between different dopants with diverse doping effects is also proposed. The results give a theoretical basis for the materials design with doped graphene as advanced materials modification for energy storage.

Characteristics of titanium oxide memristor with coexistence of dopant drift and a tunnel barrier

International Nuclear Information System (INIS)

Tian Xiao-Bo; Xu Hui

2014-01-01

The recent published experimental data of titanium oxide memristor devices which are tested under the same experimental conditions exhibit the strange instability and complexity of these devices. Such undesired characteristics preclude the understanding of the device conductive processes and the memristor-based practical applications. The possibility of the coexistence of dopant drift and tunnel barrier conduction in a memristor provides preliminary explanations for the undesired characteristics. However, current research lacks detailed discussion about the coexistence case. In this paper, dopant drift and tunnel barrier-based theories are first analyzed for studying the relations between parameters and physical variables which affect characteristics of memristors, and then the influences of each parameter change on the conductive behaviors in the single and coexistence cases of the two mechanisms are simulated and discussed respectively. The simulation results provide further explanations of the complex device conduction. Theoretical methods of eliminating or reducing the coexistence of the two mechanisms are proposed, in order to increase the stability of the device conduction. This work also provides the support for optimizing the fabrications of memristor devices with excellent performance

On exceeding the solubility limit of Cr+3 dopants in SnO2 nanoparticles based dilute magnetic semiconductors

Science.gov (United States)

URS, Kusuma; Bhat, S. V.; Kamble, Vinayak

2018-04-01

The paper investigates the magnetic behavior of chromium doped SnO2 Dilute Magnetic Semiconductor (DMS) nanoparticles, through structural, spectroscopic, and magnetic studies. A non-equilibrium solution combustion method is adopted to synthesize 0-5 at. % Cr doped SnO2 nanoparticles. The detailed spectroscopic studies on the system using micro-Raman spectroscopy, x-ray photoelectron spectroscopy, and electron paramagnetic resonance spectroscopy along with the structural analysis confirm the presence of Cr in 3+ oxidation state, which substitutes at Sn4+ site in SnO6 octahedra of the rutile structure. This doping is found to enhance the defects in the system, i.e., oxygen vacancies. All the synthesized SnO2 nanoparticles (with or without dopants) are found to exhibit Room Temperature Ferromagnetism (RTFM). This occurrence of RTFM is attributed to the magnetic exchange interaction through F-centers of oxygen vacancies as well as dopant magnetic impurities and explained through the Bound Magnetic Polaron (BMP) model of DMS systems. Nonetheless, as the doping of Cr is further increased beyond 2%, the solubility limit is achieved. This antiferromagnetic exchange interaction from interstitial Cr dopants dominates over the BMP mechanism and, hence, leads to the decrease in the net magnetic moment drastically.

Screening based approach and dehydrogenation kinetics for MgH2: Guide to find suitable dopant using first-principles approach.

Science.gov (United States)

Kumar, E Mathan; Rajkamal, A; Thapa, Ranjit

2017-11-14

First-principles based calculations are performed to investigate the dehydrogenation kinetics considering doping at various layers of MgH 2 (110) surface. Doping at first and second layer of MgH 2 (110) has a significant role in lowering the H 2 desorption (from surface) barrier energy, whereas the doping at third layer has no impact on the barrier energy. Molecular dynamics calculations are also performed to check the bonding strength, clusterization, and system stability. We study in details about the influence of doping on dehydrogenation, considering the screening factors such as formation enthalpy, bulk modulus, and gravimetric density. Screening based approach assist in finding Al and Sc as the best possible dopant in lowering of desorption temperature, while preserving similar gravimetric density and Bulk modulus as of pure MgH 2 system. The electron localization function plot and population analysis illustrate that the bond between Dopant-Hydrogen is mainly covalent, which weaken the Mg-Hydrogen bonds. Overall we observed that Al as dopant is suitable and surface doping can help in lowering the desorption temperature. So layer dependent doping studies can help to find the best possible reversible hydride based hydrogen storage materials.

Improved dehydrogenation of TiF{sub 3}-doped NaAIH{sub 4} using mesoporous SiO{sub 2} as a co-dopant

Energy Technology Data Exchange (ETDEWEB)

Li, Y.; Zheng, S.; Fang, F.; Song, Y.; Sun, D. [Fudan Univ., Shanghai (China). Dept. of Materials Science

2010-07-01

This paper examined the improved dehydrogenation of titanium fluoride (TiF{sub 3})-doped sodium aluminum hydride (NaAIH{sub 4}) using mesoporous silicon dioxide (SiO{sub 2}) as a Co-dopant. The study revealed that the amount of hydrogen evolved was 3.8 wt. per cent for the pristine NaAlH{sub 4} and approximately 4.2 wt. per cent for the TiF{sub 3}-doped NaAlH{sub 4}. It increased to 4.9-5.0 wt. per cent once the samples were doped with mesoporous SiO{sub 2}. A favorable synergistic effect on the NaAlH{sub 4} dehydrogenation was achieved as mesoporous SiO{sub 2} was added as a co-dopant along with TiF{sub 3} which was associated with the nanosized pores and high specific surface area of mesoporous SiO{sub 2}. The catalytic mechanism of mesoporous SiO{sub 2} was more physical than chemical relative to the catalytic mechanism of TiF{sub 3}. 1 fig.

Towards chiral distributions of dopants in microporous frameworks: helicoidal supramolecular arrangement of (1R,2S)-ephedrine and transfer of chirality.

Science.gov (United States)

Gómez-Hortigüela, Luis; Álvaro-Muñoz, Teresa; Bernardo-Maestro, Beatriz; Pérez-Pariente, Joaquín

2015-01-07

A molecular-mechanics computational study is performed in order to analyze the arrangement of (1R,2S)-(-)-ephedrine molecules within the 12-MR channels of the AFI aluminophosphate microporous framework and the influence on the spatial distribution of dopants embedded in the tetrahedral network. Results showed that ephedrine molecules arrange exclusively as dimers by π-π stacking of the aromatic rings within the AFI channels. Interestingly, the asymmetric nature of ephedrine and the presence of H-bond-forming groups (NH2 and OH) involve a preferential orientation where consecutive dimers within the channels are rotated by an angle of +30°; this is driven by the establishment of inter-dimer H-bonds. This preferential orientation leads to the development of a supramolecular enantiomerically-pure helicoidal (chiral) arrangement of ephedrine dimers. In addition, the computational results demonstrate that the particular molecular structure of ephedrine imparts a strong trend to attract negative charges to the vicinity of the NH2(+) positively-charged groups. Hence divalent dopants such as Mg, whose replacement by trivalent Al in the aluminophosphate network involves the generation of a negative charge, will tend to locate close to the NH2(+) molecular groups, suggesting that an imprinting of the organic arrangement to the spatial distribution of dopants would be feasible. Combined with the trend of ephedrine to arrange in a helicoidal fashion, an enantiomerically-pure helicoidal distribution of dopants would be expected, thus inducing a new type of chirality in microporous materials.

In silico optimization of phase-change materials for digital memories: a survey of first-row transition-metal dopants for Ge₂Sb₂Te₅.

Science.gov (United States)

Skelton, J M; Elliott, S R

2013-05-22

Phase-change materials are the alloys at the heart of an emerging class of next-generation, non-volatile digital memory technologies. However, the widely studied Ge-Sb-Te system possesses several undesirable properties, and enhancing its properties, e.g. by doping, is an area of active research. Various first-row transition-metal dopants have been shown to impart useful property enhancements, but a systematic study of the entire period has yet to be undertaken, and little has been done to investigate their interaction with the host material at the atomic level. We have carried out first-principles computer simulations of the complete phase-change cycle in Ge2Sb2Te5 doped with each of the ten first-row transition metals. In this article, we present a comprehensive survey of the electronic, magnetic and optical properties of these doped materials. We discuss in detail their atomic-level structure, and relate the microscopic behaviours of the dopant atoms to their influence on the Ge2Sb2Te5 host. By considering an entire family of similar materials, we identify trends and patterns which might be used to predict suitable dopants for optimizing materials for specific phase-change applications. The computational method employed here is general, and this materials-discovery approach could be applied in the future to study other families of potential dopants for such materials.

Phosphorus {delta}-doped silicon: mixed-atom pseudopotentials and dopant disorder effects

Energy Technology Data Exchange (ETDEWEB)

Carter, Damien J; Marks, Nigel A [Nanochemistry Research Institute, Curtin University, PO Box U1987, Perth WA 6845 (Australia); Warschkow, Oliver; McKenzie, David R, E-mail: d.carter@curtin.edu.au [Centre for Quantum Computer Technology, School of Physics, University of Sydney, Sydney, NSW 2006 (Australia)

2011-02-11

Within a full density functional theory framework we calculate the band structure and doping potential for phosphorus {delta}-doped silicon. We compare two different representations of the dopant plane; pseudo-atoms in which the nuclear charge is fractional between silicon and phosphorus, and explicit arrangements employing distinct silicon and phosphorus atoms. While the pseudo-atom approach offers several computational advantages, the explicit model calculations differ in a number of key points, including the valley splitting, the Fermi level and the width of the doping potential. These findings have implications for parameters used in device modelling.

Multijunction Photovoltaic Technologies for High-Performance Concentrators: Preprint

Energy Technology Data Exchange (ETDEWEB)

McConnell, R.; Symko-Davies, M.

2006-05-01

Multijunction solar cells provide high-performance technology pathways leading to potentially low-cost electricity generated from concentrated sunlight. The National Center for Photovoltaics at the National Renewable Energy Laboratory has funded different III-V multijunction solar cell technologies and various solar concentration approaches. Within this group of projects, III-V solar cell efficiencies of 41% are close at hand and will likely be reported in these conference proceedings. Companies with well-developed solar concentrator structures foresee installed system costs of $3/watt--half of today's costs--within the next 2 to 5 years as these high-efficiency photovoltaic technologies are incorporated into their concentrator photovoltaic systems. These technology improvements are timely as new large-scale multi-megawatt markets, appropriate for high performance PV concentrators, open around the world.

Change in Dielectric Properties in the Microwave Frequency Region of Polypyrrole–Coated Textiles during Aging

Directory of Open Access Journals (Sweden)

Eva Hakansson

2016-07-01

Full Text Available Complex permittivity of conducting polypyrrole (PPy-coated Nylon-Lycra textiles is measured using a free space transmission measurement technique over the frequency range of 1–18 GHz. The aging of microwave dielectric properties and reflection, transmission and absorption for a period of 18 months is demonstrated. PPy-coated fabrics are shown to be lossy over the full frequency range. The levels of absorption are shown to be higher than reflection in the tested samples. This is attributed to the relatively high resistivity of the PPy-coated fabrics. Both the dopant concentration and polymerisation time affect the total shielding effectiveness and microwave aging behaviour. Distinguishing either of these two factors as being exclusively the dominant mechanism of shielding effectiveness is shown to be difficult. It is observed that the PPy-coated Nylon-Lycra samples with a p-toluene sulfonic acid (pTSA concentration of 0.015 M and polymerisation times of 60 min and 180 min have 37% and 26% decrease in total transmission loss, respectively, upon aging for 72 weeks at room temperature (20 °C, 65% Relative humidity (RH. The concentration of the dopant also influences the microwave aging behaviour of the PPy-coated fabrics. The samples with a higher dopant concentration of 0.027 mol/L pTSA are shown to have a transmission loss of 32.6% and 16.5% for short and long polymerisation times, respectively, when aged for 72 weeks. The microwave properties exhibit better stability with high dopant concentration and/or longer polymerization times. High pTSA dopant concentrations and/or longer polymerisation times result in high microwave insertion loss and are more effective in reducing the transmission and also increasing the longevity of the electrical properties.

Introduction of high oxygen concentrations into silicon wafers by high-temperature diffusion

International Nuclear Information System (INIS)

Casse, G.; Glaser, M.; Lemeilleur, F.; Ruzin, A.; Wegrzecki, M.

1999-01-01

The tolerance of silicon detectors to hadron irradiation can be improved by the introduction of a high concentration of oxygen into the starting material. High-resistivity Floating-Zone (FZ) silicon is required for detectors used in particle physics applications. A significantly high oxygen concentration (>10 17 atoms cm -3 ) cannot readily be achieved during the FZ silicon refinement. The diffusion of oxygen at elevated temperatures from a SiO 2 layer grown on both sides of a silicon wafer is a simple and effective technique to achieve high and uniform concentrations of oxygen throughout the bulk of a 300 μm thick silicon wafer

(Invited) Pure Dopant Deposition of B and Ga for Ultrashallow Junctions in Si-based Devices

NARCIS (Netherlands)

Nanver, L.K.; Sammak, A.; Mohammadi, V.; Mok, K.R.C.; Qi, L.; Sakic, A.; Golshani, N.; Darakhshandeh, J.; Scholtes, T.M.L.; De Boer, W.B.

2012-01-01

Envisioning wide future relevance, work is reviewed here on the pure dopant deposition of boron (PureB), gallium (PureGa) and the combination of the two (PureGaB), as used in the fabrication of nanometer shallow p+n Si and/or Ge diodes. Focus is placed on the special properties that have put these

Ge p-channel tunneling FETs with steep phosphorus profile source junctions

Science.gov (United States)

Takaguchi, Ryotaro; Matsumura, Ryo; Katoh, Takumi; Takenaka, Mitsuru; Takagi, Shinichi

2018-04-01

The solid-phase diffusion processes of three n-type dopants, i.e., phosphorus (P), arsenic (As), and antimony (Sb), from spin-on-glass (SOG) into Ge are compared. We show that P diffusion can realize both the highest impurity concentration (˜7 × 1019 cm-3) and the steepest impurity profile (˜10 nm/dec) among the cases of the three n-type dopants because the diffusion coefficient is strongly dependent on the dopant concentration. As a result, we can conclude that P is the most suitable dopant for the source formation of Ge p-channel TFETs. Using this P diffusion, we fabricate Ge p-channel TFETs with high-P-concentration and steep-P-profile source junctions and demonstrate their operation. A high ON current of ˜1.7 µA/µm is obtained at room temperature. However, the subthreshold swing and ON current/OFF current ratio are degraded by any generation-recombination-related current component. At 150 K, SSmin of ˜108 mV/dec and ON/OFF ratio of ˜3.5 × 105 are obtained.

Extremely high concentration of folates in premature newborns.

Science.gov (United States)

Zikavska, T; Brucknerova, I

2014-01-01

Extremely high concentration of folates in premature newborns: case reports. Folates are a group of water soluble compounds, which are important for metabolic processes in human body. These are important during periods of rapid cell growth. The most accurate indicator of long-term folate level status in the body is the determination of red blood cell (RBC) folate concentrations. The optimal level of RBC folate is not known in neonatal period. Authors discuss the reasons for extremely high level of RBC folate concentrations. In our work we present the cases of two premature newborns with extremely high level of RBC folate concentrations, which were analyzed immunochemically on the first day of life and after six weeks of life. In both cases we measured RBC folate concentrations on the 1st day of life. After 6 weeks we found extremely high RBC folate concentration level (5516.67 ng/ml) in the first case after RBC transfusions. In second case after two months of life the RBC folate concentration level was doubled (2335.1 ng/ml) until 24 hours after RBC transfusion compared to levels after birth. The normal range of RBC folate values vary in newborns. The upper limit of daily dose of folic acid in pregnancy and neonatal period is not known. On the other hand it is an easily excreted water-soluble vitamin but in premature newborn it can lead to the disruption of metabolic balance and slow its degradation. Some factors can have an impact on RBC folate concentration. Blood transfusion can be one of the main influences on RBC folate concentration. To clarify these mechanisms further studies are required (Ref. 29).

Study of Sn and Mg doping effects on TiO2/Ge stack structure by combinatorial synthesis

Science.gov (United States)

Nagata, Takahiro; Suzuki, Yoshihisa; Yamashita, Yoshiyuki; Ogura, Atsushi; Chikyow, Toyohiro

2018-04-01

The effects of Sn and Mg doping of a TiO2 film on a Ge substrate were investigated to improve leakage current properties and Ge diffusion into the TiO2 film. For systematic analysis, dopant-composition-spread TiO2 samples with dopant concentrations of up to 20.0 at. % were fabricated by RF sputtering and a combinatorial method. X-ray photoelectron spectroscopy revealed that the instability of Mg doping of TiO2 at dopant concentrations above 10.5 at. %. Both Sn and Mg dopants reduced Ge diffusion into TiO2. Sn doping enhanced the crystallization of the rutile phase, which is a high-dielectric-constant phase, although the Mg-doped TiO2 film indicated an amorphous structure. Sn-doping indicated systematic leakage current reduction with increasing dopant concentration. Doping at Sn concentrations higher than 16.8 at. % improved the leakage properties (˜10-7 A/cm2 at -3.0 V) and capacitance-voltage properties of metal-insulator-semiconductor (MIS) operation. The Sn doping of TiO2 may be useful for interface control and as a dielectric material for Ge-based MIS capacitors.

Stress concentration effects in high pressure components

International Nuclear Information System (INIS)

Aller, J.E.

1990-01-01

This paper examines the stress concentration effects of sideholes in thick walled, high pressure cylinders. It has been shown that the theoretical stress concentration factor at the intersection of a small crossbore in a closed end, thick walled cylinder varies between 3.0 and 4.0. Tests have shown that this effect can be greatly reduced in practice by carefully radiusing the bore intersection and autofrettaging the cylinder. It has also been shown that the minimum stress concentration factor occurs when the main bore and sidehole or crossbore have the same diameter, and the radius of the intersection is approximately equal to the sidehole radius. When the bore and sidehole intersection angle decreases from 90 degrees, the stress concentration factor increases significantly. Knowledge of these fundamental relationships can be used in maintaining, as well ad designing, high pressure equipment

Doping process of p-type GaN nanowires: A first principle study

Science.gov (United States)

Xia, Sihao; Liu, Lei; Diao, Yu; Feng, Shu

2017-10-01

The process of p-type doping for GaN nanowires is investigated using calculations starting from first principles. The influence of different doping elements, sites, types, and concentrations is discussed. Results suggest that Mg is an optimal dopant when compared to Be and Zn due to its stronger stability, whereas Be atoms are more inclined to exist in the interspace of a nanowire. Interstitially-doped GaN nanowires show notable n-type conductivity, and thus, Be is not a suitable dopant, which is to be expected since systems with inner substitutional dopants are more favorable than those with surface substitutions. Both interstitial and substitutional doping affect the atomic structure near dopants and induce charge transfer between the dopants and adjacent atoms. By altering doping sites and concentrations, nanowire atomic structures remain nearly constant. Substitutional doping models show p-type conductivity, and Mg-doped nanowires with doping concentrations of 4% showing the strongest p-type conductivity. All doping configurations are direct bandgap semiconductors. This study is expected to direct the preparation of high-quality GaN nanowires.

Performance analysis of AlGaAs/GaAs tunnel junctions for ultra-high concentration photovoltaics

International Nuclear Information System (INIS)

García, I; Rey-Stolle, I; Algora, C

2012-01-01

An n ++ -GaAs/p ++ -AlGaAs tunnel junction with a peak current density of 10 100 A cm -2 is developed. This device is a tunnel junction for multijunction solar cells, grown lattice-matched on standard GaAs or Ge substrates, with the highest peak current density ever reported. The voltage drop for a current density equivalent to the operation of the multijunction solar cell up to 10 000 suns is below 5 mV. Trap-assisted tunnelling is proposed to be behind this performance, which cannot be justified by simple band-to-band tunnelling. The metal-organic vapour-phase epitaxy growth conditions, which are in the limits of the transport-limited regime, and the heavy tellurium doping levels are the proposed origins of the defects enabling trap-assisted tunnelling. The hypothesis of trap-assisted tunnelling is supported by the observed annealing behaviour of the tunnel junctions, which cannot be explained in terms of dopant diffusion or passivation. For the integration of these tunnel junctions into a triple-junction solar cell, AlGaAs barrier layers are introduced to suppress the formation of parasitic junctions, but this is found to significantly degrade the performance of the tunnel junctions. However, the annealed tunnel junctions with barrier layers still exhibit a peak current density higher than 2500 A cm -2 and a voltage drop at 10 000 suns of around 20 mV, which are excellent properties for tunnel junctions and mean they can serve as low-loss interconnections in multijunction solar cells working at ultra-high concentrations. (paper)

Case study of elevated layers of high sulfate concentration

International Nuclear Information System (INIS)

McNaughton, D.J.; Orgill, M.M.

1979-01-01

During studies in August 1976 that were part of the Multi-State Atmospheric Power Production Pollutant Study (MAP3S), Alkezweeny et al., (1977) noted that in the Milwaukee urban plume, layers of relatively high sulfate concentrations occurred at high altitudes with respect to the boundary layer. This paper represents a progress report on studies undertaken to investigate possible causes for a bimodel vertical profile of sulfate concentrations. Data presented by Alkezweeny et al., (1977) serve as a basis for this study. Data from August 23, 1976, and August 24, 1978, indicate concentrations relatively high in sulfate, at 1000 and 6000 ft, respectively, with lower concentrations at lower altitudes. Concentrations of trace metals also indicate no peaks in the vertical concentration profiles above the surface. Initial studies of the high, elevated sulfate concentrations have centered on the August 23 measurements taken over southeast Wisconsin using synoptic data from the national weather service, emissions data from the national emissions data bank system (EPA), air quality data from the national air surveillance network (EPA), and satellite photographs from the EROS Data Center

Defect- and dopant-controlled carbon nanotubes fabricated by self-assembly of graphene nanoribbons

Institute of Scientific and Technical Information of China (English)

Cun Zhang and Shaohua Chen

2015-01-01

Molecular dynamics simulations showed that a basal carbon nanotube can activate and guide the fabrication of single-walled carbon nanotubes （CNTs） on its internal surface by self-assembly of edge-unpassivated graphene nanoribbons with defects. Furthermore, the distribution of defects on self-assembled CNTs is controllable. The system temperature and defect fraction are two main factors that influence the success of self-assembly. Due to possible joint flaws formed at the boundaries under a relatively high constant temperature, a technique based on increasing the temperature is adopted. Self-assembly is always successful for graphene nanoribbons with relatively small defect fractions, while it will fail in cases with relatively large ones. Similar to the self-assembly of graphene nanoribbons with defects, graphene nanoribbons with different types of dopants can also be self-assembled into carbon nanotubes. The finding provides a possible fabrication technique not only for carbon nanotubes with metallic or semi-con- ductive properties but also for carbon nanotubes with electromagnetic induction characteristics.

Schottky Barrier Height Tuning via the Dopant Segregation Technique through Low-Temperature Microwave Annealing.

Science.gov (United States)

Fu, Chaochao; Zhou, Xiangbiao; Wang, Yan; Xu, Peng; Xu, Ming; Wu, Dongping; Luo, Jun; Zhao, Chao; Zhang, Shi-Li

2016-04-27

The Schottky junction source/drain structure has great potential to replace the traditional p/n junction source/drain structure of the future ultra-scaled metal-oxide-semiconductor field effect transistors (MOSFETs), as it can form ultimately shallow junctions. However, the effective Schottky barrier height (SBH) of the Schottky junction needs to be tuned to be lower than 100 meV in order to obtain a high driving current. In this paper, microwave annealing is employed to modify the effective SBH of NiSi on Si via boron or arsenic dopant segregation. The barrier height decreased from 0.4-0.7 eV to 0.2-0.1 eV for both conduction polarities by annealing below 400 °C. Compared with the required temperature in traditional rapid thermal annealing, the temperature demanded in microwave annealing is ~60 °C lower, and the mechanisms of this observation are briefly discussed. Microwave annealing is hence of high interest to future semiconductor processing owing to its unique capability of forming the metal/semiconductor contact at a remarkably lower temperature.

Effect of donor and acceptor dopants on crystallization, microstructural and dielectric behaviors of barium strontium titanate glass ceramics

Energy Technology Data Exchange (ETDEWEB)

Yadav, Avadhesh Kumar, E-mail: yadav.av11@gmail.com [Department of Physics, Dr. Bheem Rao Ambedkar Government Degree College, Anaugi, Kannauj (India); Gautam, C.R. [Department of Physics, University of Lucknow, Lucknow 226007 (India); Singh, Prabhakar [Department of Physics, Indian Institute of Technology (Banaras Hindu University), Varanasi 221005 (India)

2016-07-05

Bulk transparent barium strontium titanate borosilicate glasses in glass system (65-x)[(Ba{sub 0.6}Sr{sub 0.4}).TiO{sub 3}]-30[2SiO{sub 2}.B{sub 2}O{sub 3}]-5[K{sub 2}O]-x[A{sub 2}O{sub 3}], A = La, Fe (x = 2, 5 and 10) were prepared by rapid melt-quench technique and subsequently, converted into glass ceramics by regulated heat treatment process. The phase identification was carried out by X-ray powder diffraction and their surface morphology was studied by scanning electron microscopy. The dielectric properties were studied by impedance spectroscopic technique. Investigated glass samples were crystallized into major and secondary phases of Ba{sub 1.91}Sr{sub 0.09}TiO{sub 4} and Ba{sub 2}TiSi{sub 2}O{sub 8}, respectively. A very high dielectric constant having value upto 68000 was found in glass ceramic sample BST5K10F. This high value of dielectric constant was attributed to interfacial polarization, which arose due to conductivity difference among semiconducting crystalline phases, conducting grains and insulating grain boundaries. Donor dopant La{sub 2}O{sub 3} and acceptor dopant Fe{sub 2}O{sub 3} play an important role for enhancing crystallization, dielectric constant and retardation of dielectric loss in the samples. Moreover, higher value of dielectric constant and lower value of dielectric loss was found in Fe{sub 2}O{sub 3} doped samples in comparison to La{sub 2}O{sub 3} doped samples. - Highlights: • Bulk transparent barium strontium titanate glasses are successfully prepared. • A very high dielectric constant upto 68000 was found in glass ceramics. • La{sub 2}O{sub 3} and Fe{sub 2}O{sub 3} play role for enhancing value of dielectric constant. • Higher dielectric constant with low dielectric loss was found in Fe{sub 2}O{sub 3} doped sample. • Such glass ceramics may be used in making capacitors for high energy storage.

Acetate biodegradation by anaerobic microorganisms at high pH and high calcium concentration

International Nuclear Information System (INIS)

Yoshida, Takahiro

2011-01-01

Acetate biodegradation at a high pH and a high calcium concentration was examined to clarify the effect of bacterial activity on the migration of organic 14 C compounds in cementitious repositories. Tamagawa river sediment or Teganuma pond sediment was anaerobically cultured with 5 mM acetate and 10 mM nitrate at pH 9.5-12 at 30 o C. After 20 and 90 days, the acetate concentration of the culture medium was analyzed and found to have decreased below 5 mM at pH ≤ 11. On the other hand, it did not decrease when either sediment was incubated in the absence of nitrate. These results suggest that nitrate-reducing bacteria can biodegrade acetate under more alkaline conditions than the reported pH range in which nitrate-reducing bacteria can exhibit activity. Acetate biodegradation was also examined at a high calcium concentration. Sediments were anaerobically cultured at pH 9.5 with 5 mM acetate and 10 mM nitrate in solution, equilibrated with ordinary Portland cement hydrate, in which the Ca concentration was 14.6 mM. No decrease in acetate concentration after incubation of the sediments was observed, nor was it lower than in the absence of cementitious composition, suggesting that kinetics of acetate biodegradation by anaerobic microorganisms is lowered by a high Ca concentration. - Research highlights: → Acetate biodegradation at a high pH and a high calcium concentration was examined to clarify the effect of bacterial activity on the migration of organic 14 C compounds in cementitious repositories. → Nitrate-reducing bacteria can biodegrade acetate at pH ≤ 11. → Kinetics of acetate biodegradation by anaerobic microorganisms might be lowered by a high Ca concentration.

Effect of metallic dopants on the microstructure and mechanical properties of TiB2

Czech Academy of Sciences Publication Activity Database

Chlup, Zdeněk; Bača, L.; Halasová, Martina; Neubauer, E.; Hadraba, Hynek; Stelzer, N.; Roupcová, Pavla

2015-01-01

Roč. 35, č. 10 (2015), s. 2745-2754 ISSN 0955-2219 R&D Projects: GA ČR(CZ) GAP108/11/1644; GA MŠk(CZ) ED1.1.00/02.0068 Grant - others:The Austrian Research Promotion Agency (FFG)(AT) 834287 Institutional support: RVO:68081723 Keywords : Titanium diboride * Metallic dopants * Microstructure * Mechanical properties * Fracture behaviour1 Subject RIV: JL - Materials Fatigue, Friction Mechanics Impact factor: 2.933, year: 2015

Electrochemical synthesis of nanostructured Se-doped SnS: Effect of Se-dopant on surface characterizations

Science.gov (United States)

Kafashan, Hosein; Azizieh, Mahdi; Balak, Zohre

2017-07-01

SnS1-xSex nanostructures with different Se-dopant concentrations were deposited on fluorine doped tin oxide (FTO) substrate through cathodic electrodeposition technique. The pH, temperature, applied potential (E), and deposition time remained were 2.1, 60 °C, -1 V, and 30 min, respectively. SnS1-xSex nanostructures were characterized using X-ray diffraction (XRD), field emission scanning electron microcopy (FESEM), energy dispersive X-ray spectroscopy (EDX), room temperature photoluminescence (PL), and UV-vis spectroscopy. The XRD patterns revealed that the SnS1-xSex nanostructures were polycrystalline with orthorhombic structure. FESEM showed various kinds of morphologies in SnS1-xSex nanostructures due to Se-doping. PL and UV-vis spectroscopy were used to evaluate the optical properties of SnS1-xSex thin films. The PL spectra of SnS1-xSex nanostructures displayed four emission peaks, those are a blue, a green, an orange, and a red emission. UV-vis spectra showed that the optical band gap energy (Eg) of SnS1-xSex nanostructures varied between 1.22-1.65 eV, due to Se-doping.

Effects of Chromium Dopant on Ultraviolet Photoresponsivity of ZnO Nanorods

Science.gov (United States)

Mokhtari, S.; Safa, S.; Khayatian, A.; Azimirad, R.

2017-07-01

Structural and optical properties of bare ZnO nanorods, ZnO-encapsulated ZnO nanorods, and Cr-doped ZnO-encapsulated ZnO nanorods have been investigated. Encapsulated ZnO nanorods were grown using a simple two-stage method in which ZnO nanorods were first grown on a glass substrate directly from a hydrothermal bath, then encapsulated with a thin layer of Cr-doped ZnO by dip coating. Comparative study of x-ray diffraction patterns showed that Cr was successfully incorporated into the shell layer of ZnO nanorods. Moreover, energy-dispersive x-ray spectroscopy confirmed presence of Cr in this sample. It was observed that the thickness of the shell layer around the core of the ZnO nanorods was at least about 20 nm. Transmission electron microscopy of bare ZnO nanorods revealed single-crystalline structure. Based on optical results, both the encapsulation process and addition of Cr dopant decreased the optical bandgap of the samples. Indeed, the optical bandgap values of Cr-doped ZnO-encapsulated ZnO nanorods, ZnO-encapsulated ZnO nanorods, and bare ZnO nanorods were 2.89 eV, 3.15 eV, and 3.34 eV, respectively. The ultraviolet (UV) parameters demonstrated that incorporation of Cr dopant into the shell layer of ZnO nanorods considerably facilitated formation and transportation of photogenerated carriers, optimizing their performance as a practical UV detector. As a result, the photocurrent of the Cr-doped ZnO-encapsulated ZnO nanorods was the highest (0.6 mA), compared with ZnO-encapsulated ZnO nanorods and bare ZnO nanorods (0.21 mA and 0.06 mA, respectively).

HIGH PERFORMANCE CERIA BASED OXYGEN MEMBRANE

DEFF Research Database (Denmark)

2014-01-01

The invention describes a new class of highly stable mixed conducting materials based on acceptor doped cerium oxide (CeO2-8 ) in which the limiting electronic conductivity is significantly enhanced by co-doping with a second element or co- dopant, such as Nb, W and Zn, so that cerium and the co......-dopant have an ionic size ratio between 0.5 and 1. These materials can thereby improve the performance and extend the range of operating conditions of oxygen permeation membranes (OPM) for different high temperature membrane reactor applications. The invention also relates to the manufacturing of supported...

Organometallic tris(8-hydroxyquinoline)aluminum complexes as buffer layers and dopants in inverted organic solar cells

International Nuclear Information System (INIS)

Tolkki, Antti; Kaunisto, Kimmo; Heiskanen, Juha P.; Omar, Walaa A.E.; Huttunen, Kirsi; Lehtimäki, Suvi; Hormi, Osmo E.O.; Lemmetyinen, Helge

2012-01-01

Tris(8-hydroxyquinoline)aluminum (Alq 3 ) is a frequently used material for organic light emitting diodes. The electronic properties and solubility can be tuned by chemical tailoring of the quinoline part, which makes it an interesting candidate for organic solar cells. Steady-state absorption and fluorescence, as well as time-resolved fluorescence properties of the parent Alq 3 and a series of complexes consisting of derivatives, such as 4-substituted pyrazol, methylpyrazol, arylvinyl, and pyridinoanthrene moieties, of the quinoline ligand, were studied in solutions and in thin films. Suitability of the complexes as anodic buffer layers or dopants in inverted organic solar cells based on the well known bulk heterojunction of poly(3-hexylthiophene) (P3HT) and phenyl-C 61 -butyric acid methyl ester (PCBM) was tested. The devices equipped with the derivatives showed higher power conversion efficiency (η) compared to the photocells containing the parent Alq 3 . Open circuit voltage (V oc ) was increased when the derivatives were utilized as the anodic buffer layer. Doping of the P3HT:PCBM with a small amount of Alq 3 or its derivative improved short circuit current density, V oc , fill factor, and η, while the series resistance decreased. In addition, the devices were stable in air over several weeks without encapsulation. Possible mechanisms leading to the improvements in the photovoltaic performance by using the parent Alq 3 or its derivative as buffer layer or dopant are discussed. - Highlights: ► Tris(8-hydroxyquinoline)aluminum (Alq 3 ) complexes in inverted organic solar cells. ► The Alq 3 complexes were used as an anodic buffer layer and as a dopant. ► Efficiency increased and the derivatives revealed varying open circuit voltage. ► Photovoltaic performance was stable after storage in a dark ambient atmosphere.

High indoor radon concentrations in some Swedish waterworks

International Nuclear Information System (INIS)

Aakerblom, G.; Hagberg, N.; Mjoenes, L.; Heiberg, A.

2002-01-01

High indoor radon concentrations in buildings used for water treatment are not uncommon. When raw water is processed in an open system radon escapes from the water to the indoor air of the premises. It is not unusual that the staff of the waterworks have their offices in the building where the water is processed. If large volumes of water are processed and the evaporated radon can reach the workplaces the indoor radon concentration can be very high even if the radon concentration of the raw water is moderate. Groundwaters from aquifers in bedrock and soil and surface water that has been infiltrated through deposits of sand or gravel have the potential to cause high indoor radon levels. In surface water emanating directly from a lake or a river the radon concentrations are normally too low to cause problems. Three waterworks in central Sweden have been studied, Ludvika, Fredriksberg and Kolbaeck. The radon concentrations in the raw water of these waterworks are from 85 Bq/l to 300 Bq/l. Average indoor radon concentrations exceeding 17,000 Bq/m 3 have been measured in Ludvika with peaks of almost 37,000 Bq/m 3 . In Kolbaeck radon concentrations up to 56,000 Bq/m 3 have been measured. It is quite possible that employees of waterworks can receive doses exceeding 20 mSv per year (calculated according to ICRP:s dose conversion convention). Measurements of radon and gamma radiation from the waterworks are reported and methods to lower the indoor radon concentrations are discussed. (author)

Adaptive sensor-based ultra-high accuracy solar concentrator tracker

Science.gov (United States)

Brinkley, Jordyn; Hassanzadeh, Ali

2017-09-01

Conventional solar trackers use information of the sun's position, either by direct sensing or by GPS. Our method uses the shading of the receiver. This, coupled with nonimaging optics design allows us to achieve ultra-high concentration. Incorporating a sensor based shadow tracking method with a two stage concentration solar hybrid parabolic trough allows the system to maintain high concentration with acute accuracy.

High efficient white organic light emitting diodes

Energy Technology Data Exchange (ETDEWEB)

Seidel, Stefan; Krause, Ralf [Department of Materials Science VI, University of Erlangen-Nuremberg (Germany); Siemens AG, CT MM 1, Erlangen (Germany); Kozlowski, Fryderyk; Schmid, Guenter; Hunze, Arvid [Siemens AG, CT MM 1, Erlangen (Germany); Winnacker, Albrecht [Department of Materials Science VI, University of Erlangen-Nuremberg (Germany)

2007-07-01

Due to the rapid progress in the last years the performance of organic light emitting diodes (OLEDs) has reached a level where general lighting presents a most interesting application target. We demonstrate, how the color coordinates of the emission spectrum can be adjusted using a combinatorial evaporation tool to lie on the desired black body curve representing cold and warm white, respectively. The evaluation includes phosphorescent and fluorescent dye approaches to optimize lifetime and efficiency, simultaneously. Detailed results are presented with respect to variation of layer thicknesses and dopant concentrations of each layer within the OLED stack. The most promising approach contains phosphorescent red and green dyes combined with a fluorescent blue one as blue phosphorescent dopants are not yet stable enough to achieve long lifetimes.

Plasma Doping - Enabling Technology for High Dose Logic and Memory Applications

International Nuclear Information System (INIS)

Miller, T.; Godet, L.; Papasouliotis, G. D.; Singh, V.

2008-01-01

As logic and memory device dimensions shrink with each generation, there are more high dose implants at lower energies. Examples include dual poly gate (also referred to as counter-doped poly), elevated source drain and contact plug implants. Plasma Doping technology throughput and dopant profile benefits at these ultra high dose and lower energy conditions have been well established [1,2,3]. For the first time a production-worthy plasma doping implanter, the VIISta PLAD tool, has been developed with unique architecture suited for precise and repeatable dopant placement. Critical elements of the architecture include pulsed DC wafer bias, closed-loop dosimetry and a uniform low energy, high density plasma source. In this paper key performance metrics such as dose uniformity, dose repeatability and dopant profile control will be presented that demonstrate the production-worthiness of the VIISta PLAD tool for several high dose applications.

Low-temperature synthesis, structural and magnetic properties of self-dopant LaMnO{sub 3+δ} nanoparticles from a metal-organic polymeric precursor

Energy Technology Data Exchange (ETDEWEB)

Ahmad, Tokeer, E-mail: tahmad3@jmi.ac.in [Nanochemistry Laboratory, Department of Chemistry, Jamia Millia Islamia, New Delhi 110025 (India); Lone, Irfan H.; Ubaidullah, Mohd. [Nanochemistry Laboratory, Department of Chemistry, Jamia Millia Islamia, New Delhi 110025 (India); Coolhan, Kelsey [Department of Physics and Astronomy, Rowan University, 201 Mullica Hill Road, Glassboro, NJ 08028 (United States)

2013-11-15

Graphical abstract: Monophasic and highly crystalline Self-dopant LaMnO{sub 3+δ} nanoparticles (72 nm) have been successfully synthesized at low temperature (773 K) by metal citrate complex method based on Pechini-type reaction route which showed ferromagnetic interaction. Surface areas of LaMnO{sub 3+δ} nanoparticles were found to be 157.4 and 153 m{sup 2} g{sup −1} for the samples annealed at 773 K and 1173 K, respectively. - Highlights: • Self-dopant LaMnO{sub 3+δ} nanoparticles using Pechini-type reaction route at 773 K. • Size range varies from 72 to 80 nm. • Surface area varies from 153 to 157 m{sup 2} g{sup −1}. • Extensive characterization using sophisticated techniques. - Abstract: Self-dopant LaMnO{sub 3+δ} nanoparticles have been successfully synthesized by metal citrate complex method based on Pechini-type reaction route, at low temperature (773 K). Powder X-ray diffraction and transmission electron microscope revealed pure and nanostructured phase of LaMnO{sub 3+δ} (δ = 0.125) with an average grain size of ∼72 nm (773 K) and ∼80 nm (1173 K). DC-magnetization measurements under an applied magnetic field of H = ±60 kOe showed an increase in the magnetization with the increase of calcination temperature. Ferromagnetic nature shown by non-stoichiometric LaMnO{sub 3+δ} was verified by well-defined hysteresis loop with large remanent magnetization (M{sub r}) and coercive field (H{sub c}). Surface areas of LaMnO{sub 3+δ} nanoparticles were found to be 157.4 and 153 m{sup 2} g{sup −1} for the samples annealed at 773 K and 1173 K, respectively.

In silico optimization of phase-change materials for digital memories: a survey of first-row transition-metal dopants for Ge2Sb2Te5

International Nuclear Information System (INIS)

Skelton, J M; Elliott, S R

2013-01-01

Phase-change materials are the alloys at the heart of an emerging class of next-generation, non-volatile digital memory technologies. However, the widely studied Ge–Sb–Te system possesses several undesirable properties, and enhancing its properties, e.g. by doping, is an area of active research. Various first-row transition-metal dopants have been shown to impart useful property enhancements, but a systematic study of the entire period has yet to be undertaken, and little has been done to investigate their interaction with the host material at the atomic level. We have carried out first-principles computer simulations of the complete phase-change cycle in Ge 2 Sb 2 Te 5 doped with each of the ten first-row transition metals. In this article, we present a comprehensive survey of the electronic, magnetic and optical properties of these doped materials. We discuss in detail their atomic-level structure, and relate the microscopic behaviours of the dopant atoms to their influence on the Ge 2 Sb 2 Te 5 host. By considering an entire family of similar materials, we identify trends and patterns which might be used to predict suitable dopants for optimizing materials for specific phase-change applications. The computational method employed here is general, and this materials-discovery approach could be applied in the future to study other families of potential dopants for such materials. (paper)

Atomic ordering of the fluorine dopant in the $HgBa_{2}CuO_{4+\\delta}high-T_{c}$ superconductor

CERN Document Server

Correia, João Guilherme; Araújo, João Pedro; Bordet, P; Haas, Heinz; Le Floc'h, S; Lopes, A M L; Rita, E; Carvalho-Soares, João

2005-01-01

Lattice sites and collective ordering of fluorine atoms in oxygen- reduced samples of HgBa/sub 2/CuO/sub 4/ were investigated with the perturbed angular correlation technique by measuring the electric field gradients induced at /sup 199m/Hg nuclei. The experimental data were interpreted with the help of ab initio calculations of charge distributions for different fluorine configurations in Hg/sub m/Ba /sub 2m/Cu/sub m/O/sub 4m/F/sub n/, supercells. Internal parameters were allowed to relax, to cancel residual atomic forces due to the dopant. The experimental results show clearly that fluorine occupies only the center of the mercury mesh. For a fluorine content delta F>~0.35 the best agreement with theoretical data is obtained under the assumption that fluorine shows a tendency toward ordering along interstitial rows parallel to a, b. In conformity with experimental data from diffraction techniques the calculations show elongations of the O(2)-Hg-O(2) dumbbell and barium shifts towards the fluorine atoms as ef...

Effects of Zn2+ and Pb2+ dopants on the activity of Ga2O3-based photocatalysts for water splitting.

Science.gov (United States)

Wang, Xiang; Shen, Shuai; Jin, Shaoqing; Yang, Jingxiu; Li, Mingrun; Wang, Xiuli; Han, Hongxian; Li, Can

2013-11-28

Zn-doped and Pb-doped β-Ga2O3-based photocatalysts were prepared by an impregnation method. The photocatalyst based on the Zn-doped β-Ga2O3 shows a greatly enhanced activity in water splitting while the Pb-doped β-Ga2O3 one shows a dramatic decrease in activity. The effects of Zn(2+) and Pb(2+) dopants on the activity of Ga2O3-based photocatalysts for water splitting were investigated by HRTEM, XPS and time-resolved IR spectroscopy. A ZnGa2O4-β-Ga2O3 heterojunction is formed in the surface region of the Zn-doped β-Ga2O3 and a slower decay of photogenerated electrons is observed. The ZnGa2O4-β-Ga2O3 heterojunction exhibits type-II band alignment and facilitates charge separation, thus leading to an enhanced photocatalytic activity for water splitting. Unlike Zn(2+) ions, Pb(2+) ions are coordinated by oxygen atoms to form polyhedra as dopants, resulting in distorted surface structure and fast decay of photogenerated electrons of β-Ga2O3. These results suggest that the Pb dopants act as charge recombination centers expediting the recombination of photogenerated electrons and holes, thus decreasing the photocatalytic activity.

Simultaneous Conduction and Valence Band Quantization in Ultrashallow High-Density Doping Profiles in Semiconductors

Science.gov (United States)

Mazzola, F.; Wells, J. W.; Pakpour-Tabrizi, A. C.; Jackman, R. B.; Thiagarajan, B.; Hofmann, Ph.; Miwa, J. A.

2018-01-01

We demonstrate simultaneous quantization of conduction band (CB) and valence band (VB) states in silicon using ultrashallow, high-density, phosphorus doping profiles (so-called Si:P δ layers). We show that, in addition to the well-known quantization of CB states within the dopant plane, the confinement of VB-derived states between the subsurface P dopant layer and the Si surface gives rise to a simultaneous quantization of VB states in this narrow region. We also show that the VB quantization can be explained using a simple particle-in-a-box model, and that the number and energy separation of the quantized VB states depend on the depth of the P dopant layer beneath the Si surface. Since the quantized CB states do not show a strong dependence on the dopant depth (but rather on the dopant density), it is straightforward to exhibit control over the properties of the quantized CB and VB states independently of each other by choosing the dopant density and depth accordingly, thus offering new possibilities for engineering quantum matter.

Defect and dopant kinetics in laser anneals of Si

International Nuclear Information System (INIS)

La Magna, A.; Fisicaro, G.; Mannino, G.; Privitera, V.; Piccitto, G.; Svensson, B.G.; Vines, L.

2008-01-01

In this work a modeling approach is applied to investigate the kinetics of the defect-dopant system in the extremely far-from-the equilibrium conditions caused by the laser irradiation in Si. A rigorous derivation of the master equations for the evolution of the defect-impurity system is obtained starting from the Boltzmann's formalism. The model derived is not limited by the stringent hypothesis of instantaneous equilibration of the local system energy to the lattice thermal field. This fact allows: (a) the formalization of a reliable theoretical formalism for the study of evolving defect-impurity systems in a non-uniform fast varying thermal field and (b) the generalization of the kinetic parameters (e.g. diffusivity, clustering rate constants, etc.). Early comparisons between simulations and experimental analysis of the processes are discussed. These results indicate the reliability of the energetic calibration for the self-interstitial clusters derived using conventional thermal processes

Effects of added dopants on various triboluminescent properties of europium dibenzoylmethide triethylammonium (EuD4TEA)

Science.gov (United States)

Owens, Constance; Fontenot, Ross S.; Bhat, Kamala N.; Aggarwal, Mohan D.

2014-03-01

A triboluminescent (TL) material is one that emits light upon pressure, impact, friction, or mechanical shock. TL materials are desirable for investigation because they have the potential to be used as the active element for smart impact sensors. While the material europium dibenzoylmethide triethylammonium (EuD4TEA) produces a TL emission yield that can be observed by the naked eye, it is still not sufficiently bright for use in smart sensor devices. Previous studies have shown that additional materials can be combined with EuD4TEA in order to improve the TL emission yield. In this paper, we discuss the effects of doping on EuD4TEA at different concentrations with a variety of materials on the TL emission yield and decay times. The dopants that were used in this study were nicotine, dibutyl phosphate (DBP), and magnesium. We also discuss both the effects of pH on EuD4TEA, and the doping effects on impact energy. For testing triboluminescent properties, we use a custom-built drop tower that generates triboluminescence by fracturing compounds through impact. Collected data is analyzed using specially written LabVIEW programs.

Study of the chlorine as dopant in synthesized polymers by plasma

International Nuclear Information System (INIS)

Vasquez, M.; Cruz, G.; Olayo, M.G.; Timoshina, T.; Morales, J.; Olayo, R.

2003-01-01

In the search of new and better dopants for semiconductor polymers, in this work the synthesis by plasma and the characterization of two doped polymers with chlorine, Pyrrole (PPy) and Thiophene (PTh) is presented. The characterization of the polymers it was carried out by FT-lR, it shows the C-Cl vibration that it is confirmed with the X-ray photoelectron spectroscopy technique (XPS). The elementary analysis shows a greater quantity of Cl in the PTh-CI compared with PPy-CI. However, this effect is not reflected in the electric conductivity since the PTh-Cl presents a lightly greater conductivity than the PPy-CI. SEM shows a formed structure of small agglomerated spheres of different size. (Author)

Synthesis of Some Green Dopants for OLEDs Based on Arylamine 2,3-disubstituted Bithiophene Derivatives

Directory of Open Access Journals (Sweden)

Mi-Seon Song

2013-11-01

Full Text Available A series of green dopants based on 2,2-diphenylvinyl end-capped bithiophene and three different arylamine moieties (9-phenylcarbazole, triphenylamine, and N,N’-di-(p-tolylbenzeneamine were successfully synthesized by the Suzuki and Wittig coupling reactions. The photophysical properties of these compounds are reported. The strongest PL emitting compound with the 9-phenylcarbazole moiety has been used for fabricating an OLED device with good overall performance.

High-performance flat-panel solar thermoelectric generators with high thermal concentration

Science.gov (United States)

Kraemer, Daniel; Poudel, Bed; Feng, Hsien-Ping; Caylor, J. Christopher; Yu, Bo; Yan, Xiao; Ma, Yi; Wang, Xiaowei; Wang, Dezhi; Muto, Andrew; McEnaney, Kenneth; Chiesa, Matteo; Ren, Zhifeng; Chen, Gang

2011-07-01

The conversion of sunlight into electricity has been dominated by photovoltaic and solar thermal power generation. Photovoltaic cells are deployed widely, mostly as flat panels, whereas solar thermal electricity generation relying on optical concentrators and mechanical heat engines is only seen in large-scale power plants. Here we demonstrate a promising flat-panel solar thermal to electric power conversion technology based on the Seebeck effect and high thermal concentration, thus enabling wider applications. The developed solar thermoelectric generators (STEGs) achieved a peak efficiency of 4.6% under AM1.5G (1 kW m-2) conditions. The efficiency is 7-8 times higher than the previously reported best value for a flat-panel STEG, and is enabled by the use of high-performance nanostructured thermoelectric materials and spectrally-selective solar absorbers in an innovative design that exploits high thermal concentration in an evacuated environment. Our work opens up a promising new approach which has the potential to achieve cost-effective conversion of solar energy into electricity.

High-performance flat-panel solar thermoelectric generators with high thermal concentration.

Science.gov (United States)

Kraemer, Daniel; Poudel, Bed; Feng, Hsien-Ping; Caylor, J Christopher; Yu, Bo; Yan, Xiao; Ma, Yi; Wang, Xiaowei; Wang, Dezhi; Muto, Andrew; McEnaney, Kenneth; Chiesa, Matteo; Ren, Zhifeng; Chen, Gang

2011-05-01

The conversion of sunlight into electricity has been dominated by photovoltaic and solar thermal power generation. Photovoltaic cells are deployed widely, mostly as flat panels, whereas solar thermal electricity generation relying on optical concentrators and mechanical heat engines is only seen in large-scale power plants. Here we demonstrate a promising flat-panel solar thermal to electric power conversion technology based on the Seebeck effect and high thermal concentration, thus enabling wider applications. The developed solar thermoelectric generators (STEGs) achieved a peak efficiency of 4.6% under AM1.5G (1 kW m(-2)) conditions. The efficiency is 7-8 times higher than the previously reported best value for a flat-panel STEG, and is enabled by the use of high-performance nanostructured thermoelectric materials and spectrally-selective solar absorbers in an innovative design that exploits high thermal concentration in an evacuated environment. Our work opens up a promising new approach which has the potential to achieve cost-effective conversion of solar energy into electricity. © 2011 Macmillan Publishers Limited. All rights reserved

Facile, one-pot and scalable synthesis of highly emissive aqueous-based Ag,Ni:ZnCdS/ZnS core/shell quantum dots with high chemical and optical stability

Science.gov (United States)

Sahraei, Reza; Soheyli, Ehsan; Faraji, Zahra; Soleiman-Beigi, Mohammad

2017-11-01

We report here on a one-pot, mild and low cost aqueous-based synthetic route for the preparation of colloidally stable and highly luminescent dual-doped Ag,Ni:ZnCdS/ZnS core/shell quantum dots (QDs). The pure dopant emission of the Ni-doped core/shell QDs was found to be highly affected by the presence of a second dopant ion (Ag+). Results showed that the PL emission intensity increases while its peak position experiences an obvious blue shift with an increase in the content of Ag+ ions. Regarding the optical observations, we provide a simple scheme for absorption-recombination processes of the carriers through impurity centers. To obtain optimum conditions with a better emission characteristic, we also study the effect of different reaction parameters, such as refluxing temperature, the pH of the core and shell solution, molar ratio of the dopant ions (Ni:(Zn+Cd) and Ag:(Zn+Cd)), and concentration of the core and shell precursors. Nonetheless, the most effective parameter is the presence of the ZnS shell in a suitable amount to eliminate surface trap states and enhance their emission intensity. It can also improve the bio-compatibility of the prepared QDs by restricting the Cd2+ toxic ions inside the core of the QDs. The present suggested route also revealed the remarkable optical and chemical stability of the colloidal QDs which establishes them as a decent kind of nano-scale structure for light emitting applications, especially in biological technologies. The suggested process also has the potential to be scaled-up while maintaining the emission characteristics and structural quality necessary for industrial applications in optoelectronic devices.

Use of Cu+1 dopant and it's doping effects on polyaniline conducting system in water and tetrahydrofuran

Science.gov (United States)

Ali, Vazid; Kaur, Raminder; Kamal, Neel; Singh, Sukhmehar; Jain, S. C.; Kang, H. P. S.; Zulfequar, M.; Husain, M.

2006-04-01

The structural modification and properties of polymeric materials are of utmost importance in deciding their applications. In the present study, the synthesis of polyaniline (PANI) has been carried out via chemical oxidation in acidic medium by potassium-dichromate and the yield of synthesized polyaniline was found to be 75 80%. The copper per chlorate tetrabenzonitrile salt (CuClO4·4BN) used for chemical doping in synthesized polyaniline is stable in organic solvent like acetonitrile (AN) and benzonitrile (BN). The effect of Cu+1 oxidation state (dopant) in polyaniline has been characterized by FTIR. Electrical and dielectric measurements show the decrease in the intensity of the Cu+1 salt signal and the appearance of a radical signal due to the formation of oxidative coupled in polymeric species. Electrical and dielectric properties of doped polyaniline samples show significant changes due to the effect of dopant (CuClO4·4BN). It is observed that the conductivity is contributing both by formation of ionic complex and particularly dominated by electronic due to the mobility of charge carriers along the polyaniline chain.

Quantum confined Stark effects of single dopant in polarized hemispherical quantum dot: Two-dimensional finite difference approach and Ritz-Hassé variation method

Science.gov (United States)

El Harouny, El Hassan; Nakra Mohajer, Soukaina; Ibral, Asmaa; El Khamkhami, Jamal; Assaid, El Mahdi

2018-05-01

Eigenvalues equation of hydrogen-like off-center single donor impurity confined in polarized homogeneous hemispherical quantum dot deposited on a wetting layer, capped by insulated matrix and submitted to external uniform electric field is solved in the framework of the effective mass approximation. An infinitely deep potential is used to describe effects of quantum confinement due to conduction band offsets at surfaces where quantum dot and surrounding materials meet. Single donor ground state total and binding energies in presence of electric field are determined via two-dimensional finite difference approach and Ritz-Hassé variation principle. For the latter method, attractive coulomb correlation between electron and ionized single donor is taken into account in the expression of trial wave function. It appears that off-center single dopant binding energy, spatial extension and radial probability density are strongly dependent on hemisphere radius and single dopant position inside quantum dot. Influence of a uniform electric field is also investigated. It shows that Stark effect appears even for very small size dots and that single dopant energy shift is more significant when the single donor is near hemispherical surface.

Effect of dye-doped concentration on the charge carrier recombination in molecularly doped organic light-emitting devices

Energy Technology Data Exchange (ETDEWEB)

Chen Jiangshan; Ma Dongge [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Graduate School of the Chinese Academy of Sciences, Changchun 130022 (China)

2006-05-21

The effect of the concentration of 4-(dicyanomethylene)-2-t-butyl-6- (1, 1, 7, 7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB) as dopant in tris(8-hydroxyquinoline) aluminium (Alq{sub 3}) on the charge carrier recombination was studied by transient electroluminescence (EL). The electron-hole recombination coefficient ({gamma}) was determined from the long-time component of the temporal decay of the EL intensity after a rectangular voltage pulse was turned off. It was found that the coefficient monotonically decreased with an increase in the DCJTB-doping concentration. The monotonic decrease is attributed to concentration quenching on the excitons and coincided well with the reduction of the EL efficiency.

Influence of photochemical transformations upon optic-spectral characteristics of iodine cadmium crystals with copper dopant

International Nuclear Information System (INIS)

Novosad, S.S.

2000-01-01

The influence of photochemical transformations upon absorption. X-ray, photo- and thermostimulated luminescence of crystals CdI 2 :CuI, CdI 2 :CuI and CdI 2 :CuO grown by Stockbarger - Czochralski method has been studied. The photochemical reactions in crystals of iodine cadmium with the dopant of copper leads to reducing the intensity of X-ray, photo- and thermostimulated luminescence, the appearance of new luminescent centers is not observed

Effect of Low Nickel Dopant on Torque Transducer Response Function in High-Chromium Content ESR Stainless Tool Steels

Science.gov (United States)

Wiewel, Joseph L.; Hecox, Bryan G.; Orris, Jason T.; Boley, Mark S.

2007-03-01

The change in magnetoelastic torque transducer response was investigated as a low nickel content (up to 0.2%) is alloyed into an ESR (Electro-Slag-Refining) stainless tool steel with a chromium content of around 13%, which our previous studies have proven to be the ideal level of chromium content for optimal transducer performance. Two separate hollow steel 3/4-inch diameter shafts were prepared from ESR 416 and ESR 420 steel, respectively, the first having no nickel content and the second having 0.2% nickel content. The heat treatment of these steels consisted of a hardening process conducted in a helium atmosphere at 1038^oC, followed by an annealing at 871^oC for 5h and a 15^oC cool down rate. Prior and subsequent to the heat treatment processes, the circumferential and axial magnetic hysteresis properties of the samples were measured and their external field signals were mapped over the magnetically polarized regions both with and without applied shear stress up to 2500 psi on the samples. It was found that the effect of the low nickel dopant was to improve torque transducer sensitivity and linearity, but heat treatment worsened the performance of both samples.

Improving solid-state hydriding and dehydriding properties of the LiBH{sub 4} plus MgH{sub 2} system with the addition of Mn and V dopants

Energy Technology Data Exchange (ETDEWEB)

Crosby, Kyle; Wan, Xuefei; Shaw, Leon L. [Department of Chemical, Materials and Biomolecular Engineering, University of Connecticut, 97 North Eagleville Road, U-3136, Storrs, CT 06269 (United States)

2010-11-01

The hydriding process of the 2LiH + MgB{sub 2} mixture is controlled by outward diffusion of Mg and inward diffusion of Li and H within MgB{sub 2} crystals to form LiBH{sub 4}. This study explores the feasibility of using transition metal dopants, such as Mn and V, to enhance the diffusion rate and thus the hydriding kinetics. It is found that Mn can indeed enhance the hydriding kinetics of the 2LiH + MgB{sub 2} mixture, while V does not. The major factor in enhancing the diffusion rate and thus the hydriding kinetics is related to the dopant's ability to induce the lattice distortion of MgB{sub 2} crystals. This study demonstrates that the kinetics of the diffusion controlled solid-state hydriding process can be improved by doping if the dopant is properly selected. (author)

Organometallic tris(8-hydroxyquinoline)aluminum complexes as buffer layers and dopants in inverted organic solar cells

Energy Technology Data Exchange (ETDEWEB)

Tolkki, Antti, E-mail: antti.tolkki@tut.fi [Department of Chemistry and Bioengineering, Tampere University of Technology, P.O. Box 541, FI-33101, Tampere (Finland); Kaunisto, Kimmo [Department of Chemistry and Bioengineering, Tampere University of Technology, P.O. Box 541, FI-33101, Tampere (Finland); Heiskanen, Juha P. [Department of Chemistry and Bioengineering, Tampere University of Technology, P.O. Box 541, FI-33101, Tampere (Finland); Department of Chemistry, University of Oulu, P.O. Box 3000, FI-90014, Oulu (Finland); Omar, Walaa A.E. [Department of Chemistry, University of Oulu, P.O. Box 3000, FI-90014, Oulu (Finland); Chemistry Branch, Department of Science and Mathematics, Suez Canal University, Suez 43721 (Egypt); Huttunen, Kirsi; Lehtimaeki, Suvi [Department of Chemistry and Bioengineering, Tampere University of Technology, P.O. Box 541, FI-33101, Tampere (Finland); Hormi, Osmo E.O. [Department of Chemistry, University of Oulu, P.O. Box 3000, FI-90014, Oulu (Finland); Lemmetyinen, Helge [Department of Chemistry and Bioengineering, Tampere University of Technology, P.O. Box 541, FI-33101, Tampere (Finland)

2012-04-30

Tris(8-hydroxyquinoline)aluminum (Alq{sub 3}) is a frequently used material for organic light emitting diodes. The electronic properties and solubility can be tuned by chemical tailoring of the quinoline part, which makes it an interesting candidate for organic solar cells. Steady-state absorption and fluorescence, as well as time-resolved fluorescence properties of the parent Alq{sub 3} and a series of complexes consisting of derivatives, such as 4-substituted pyrazol, methylpyrazol, arylvinyl, and pyridinoanthrene moieties, of the quinoline ligand, were studied in solutions and in thin films. Suitability of the complexes as anodic buffer layers or dopants in inverted organic solar cells based on the well known bulk heterojunction of poly(3-hexylthiophene) (P3HT) and phenyl-C{sub 61}-butyric acid methyl ester (PCBM) was tested. The devices equipped with the derivatives showed higher power conversion efficiency ({eta}) compared to the photocells containing the parent Alq{sub 3}. Open circuit voltage (V{sub oc}) was increased when the derivatives were utilized as the anodic buffer layer. Doping of the P3HT:PCBM with a small amount of Alq{sub 3} or its derivative improved short circuit current density, V{sub oc}, fill factor, and {eta}, while the series resistance decreased. In addition, the devices were stable in air over several weeks without encapsulation. Possible mechanisms leading to the improvements in the photovoltaic performance by using the parent Alq{sub 3} or its derivative as buffer layer or dopant are discussed. - Highlights: Black-Right-Pointing-Pointer Tris(8-hydroxyquinoline)aluminum (Alq{sub 3}) complexes in inverted organic solar cells. Black-Right-Pointing-Pointer The Alq{sub 3} complexes were used as an anodic buffer layer and as a dopant. Black-Right-Pointing-Pointer Efficiency increased and the derivatives revealed varying open circuit voltage. Black-Right-Pointing-Pointer Photovoltaic performance was stable after storage in a dark ambient

High yield and facile microwave-assisted synthesis of conductive H_2SO_4 doped polyanilines

International Nuclear Information System (INIS)

Gizdavic-Nikolaidis, Marija R.; Jevremovic, Milutin M.; Milenkovic, Maja; Allison, Morgan C.; Stanisavljev, Dragomir R.; Bowmaker, Graham A.; Zujovic, Zoran D.

2016-01-01

The microwave-assisted synthesis of polyaniline (PANI) was performed using ammonium persulphate (APS) as oxidizing agent in 0.5 M–2.5 M concentration range of aqueous sulphuric acid (H_2SO_4) at 93 W applied microwave power of 10 min duration. The microwave (MW) synthesized PANIs had 3 times higher yield in comparison to PANI samples prepared using a classical method, CS (0 W MW power) at the same temperature for 10 min synthesis duration period. Fourier Transform Infrared (FTIR) and UV–Vis spectroscopies confirmed the formation of PANI structure in all products. The influence of H_2SO_4 acid dopant on the spin concentration of MW and CS H_2SO_4 doped PANI samples were examined by EPR spectroscopy, while the morphological characteristics were investigated by using scanning electron microscopy (SEM). XRD results showed amorphous phases in both MW and CS H_2SO_4 doped PANI samples. Conductivity measurements revealed ∼1.5 times higher conductivity values for MW H_2SO_4 doped PANI samples in comparison with PANI samples prepared by the CS method under same condition. The influence of sulfate anion in comparison to chloride anion as a dopant on morphological, dopant levels and conductivity properties of MW PANI samples were also investigated. - Highlights: • Nanoporous microwave synthesized doped polyanilines as chemical sensor material. • Morphology and physical properties of polyanilines depend on acid concentration. • Spin concentration is determined by the nature of the polyaniline synthesis.

Diffusion des dopants dans les dispositifs de la microélectronique : codiffusion de l'arsenic et du phosphore dans le silicium, étude unidimensionnelle et bidimensionnelle.

OpenAIRE

Rodriguez , Nicolas

2008-01-01

Si dopant diffusion in microelectronics devices has been studied in 1 and 2 dimensions. The codiffusion effects of As and P have been characterized for “drains” and “sources” fabrication of the latest transistor technology (90 nm). If these 2 dopants are concurrently located in Si, we observe an acceleration of As and P diffusion. This effect mainly depends on the As dose, and seems to be due to the modification of AsnV cluster characteristics and to an excess of vacancies in the coexistence ...

Applications of nonimaging optics for very high solar concentrations

International Nuclear Information System (INIS)

O'Gallagher, J.; Winston, R.

1997-01-01

Using the principles and techniques of nonimaging optics, solar concentrations that approach the theoretical maximum can be achieved. This has applications in solar energy collection wherever concentration is desired. In this paper, we survey recent progress in attaining and using high and ultrahigh solar fluxes. We review a number of potential applications for highly concentrated solar energy and the current status of the associated technology. By making possible new and unique applications for intense solar flux, these techniques have opened a whole new frontier for research and development of potentially economic uses of solar energy

Contributed Review: A review of the investigation of rare-earth dopant profiles in optical fibers

Energy Technology Data Exchange (ETDEWEB)

Sidiroglou, F.; Baxter, G. [Optical Technology Research Laboratory, College of Engineering and Science, Victoria University, P.O. Box 14428, Melbourne, VIC 8001 (Australia); Roberts, A. [School of Physics, The University of Melbourne, Melbourne, VIC 3010 (Australia)

2016-04-15

Rare-earth doped optical fibers have captivated the interest of many researchers around the world across the past three decades. The growth of this research field has been stimulated primarily through their application in optical communications as fiber lasers and amplifiers, although rare-earth doped optical fiber based devices are now finding important uses in many other scientific and industrial areas (for example, medicine, sensing, the military, and material processing). Such wide commercial interest has provided a strong incentive for innovative fiber designs, alternative glass compositions, and novel fabrication processes. A prerequisite for the ongoing progress of this research field is developing the capacity to provide high resolution information about the rare-earth dopant distribution profiles within the optical fibers. This paper constitutes a comprehensive review of the imaging techniques that have been utilized in the analysis of the distribution of the rare-earth ion erbium within the core of optical fibers.

Rheological behavior of high-concentration sodium caseinate dispersions.

Science.gov (United States)

Loveday, Simon M; Rao, M Anandha; Creamer, Lawrence K; Singh, Harjinder

2010-03-01

Apparent viscosity and frequency sweep (G', G'') data for sodium caseinate dispersions with concentrations of approximately 18% to 40% w/w were obtained at 20 degrees C; colloidal glass behavior was exhibited by dispersions with concentration >or=23% w/w. The high concentrations were obtained by mixing frozen powdered buffer with sodium caseinate in boiling liquid nitrogen, and allowing the mixtures to thaw and hydrate at 4 degrees C. The low-temperature G'-G'' crossover seen in temperature scans between 60 and 5 degrees C was thought to indicate gelation. Temperature scans from 5 to 90 degrees C revealed gradual decrease in G' followed by plateau values. In contrast, G'' decreased gradually and did not reach plateau values. Increase in hydrophobicity of the sodium caseinate or a decrease in the effective volume fraction of its aggregates may have contributed to these phenomena. The gelation and end of softening temperatures of the dispersions increased with the concentration of sodium caseinate. From an Eldridge-Ferry plot, the enthalpy of softening was estimated to be 29.6 kJ mol(-1). The results of this study should be useful for creating new products with high concentrations of sodium caseinate.

Simulation of plasma loading of high-pressure RF cavities

Energy Technology Data Exchange (ETDEWEB)

Yu, K. [Brookhaven National Lab. (BNL), Upton, NY (United States). Computational Science Initiative; Samulyak, R. [Brookhaven National Lab. (BNL), Upton, NY (United States). Computational Science Initiative; Stony Brook Univ., NY (United States). Dept. of Applied Mathematics and Statistics; Yonehara, K. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Freemire, B. [Northern Illinois Univ., DeKalb, IL (United States)

2018-01-11

Muon beam-induced plasma loading of radio-frequency (RF) cavities filled with high pressure hydrogen gas with 1% dry air dopant has been studied via numerical simulations. The electromagnetic code SPACE, that resolves relevant atomic physics processes, including ionization by the muon beam, electron attachment to dopant molecules, and electron-ion and ion-ion recombination, has been used. Simulations studies have also been performed in the range of parameters typical for practical muon cooling channels.

Simulation of plasma loading of high-pressure RF cavities

Science.gov (United States)

Yu, K.; Samulyak, R.; Yonehara, K.; Freemire, B.

2018-01-01

Muon beam-induced plasma loading of radio-frequency (RF) cavities filled with high pressure hydrogen gas with 1% dry air dopant has been studied via numerical simulations. The electromagnetic code SPACE, that resolves relevant atomic physics processes, including ionization by the muon beam, electron attachment to dopant molecules, and electron-ion and ion-ion recombination, has been used. Simulations studies have been performed in the range of parameters typical for practical muon cooling channels.

Comparison of high-density carbon implosions in unlined uranium versus gold hohlraums

Science.gov (United States)

Dewald, Eduard; Meezan, Nathan; Tommasini, Riccardo; Khan, Shahab; MacKinnon, Andrew; Berzak Hopkins, Laura; Divol, Laurent; Lepape, Sebastien; Moore, Alastair; Schneider, Marilyn; Pak, Arthur; Nikroo, Abbas; Landen, Otto

2016-10-01

In Inertial Confinement Fusion (ICF) implosions, laser energy is converted to x-ray radiation in hohlraums with High-Z walls. At radiation temperatures near 300 eV relevant for ICF experiments, the radiative losses in heating the wall are lower for U than for Au hohlraums. Furthermore, the intensity of the ``M-band'' x-rays with photon energies h ν >1.8 keV is lower for uranium, allowing for reduced capsule dopant concentrations employed to minimize inner ablator preheat and hence keep favorable fuel/ablator interface Atwood numbers. This in turn improves the ablator rocket efficiency and reduces the risk of polluting the hot-spot with emissive dopant material. The first uranium vacuum hohlraum experiments on the National Ignition Facility (NIF) with undoped high-density carbon (HDC, or diamond) capsules have demonstrated 30% lower ``M-band'' intensity relative to Au, resulting in lower inflight ablator thickness due to reduced preheat. In addition, fusion neutron yields are 2x higher in U than in Au hohlraums for D2-gas filled capsule implosions at ICF relevant velocities of 380 +/-20 km/s. These results have led the NIF ICF implosions to routinely employ U hohlraums. Prepared by LLNL under Contract DE-AC52-07NA27344.

Denitrification of fertilizer wastewater at high chloride concentration

DEFF Research Database (Denmark)

Ucisik, Ahmed Süheyl; Henze, Mogens

Wastewater from fertilizer industry is characterized by high contents of chloride concentration, which normally vary between 60 and 76 g/l. Experiments with bilogical denitrification were performed in lab-scale "fill and draw" reactors with synthetic wastewater with chloride concentrations up to 77.......4 g/l. The results of the experiments showed that biological denitrification was feasible at the extreme environmental conditions prevailing in fertilizer wastewater. Stable continuous biological denitrfication of the synthetic high chloride wastewater was performed up to 77.4 g Cl/l at 37 degree C...

Growth temperature and dopant species effects on deep levels in Si grown by low temperature molecular beam epitaxy

International Nuclear Information System (INIS)

Chung, Sung-Yong; Jin, Niu; Rice, Anthony T.; Berger, Paul R.; Yu, Ronghua; Fang, Z-Q.; Thompson, Phillip E.

2003-01-01

Deep-level transient spectroscopy measurements were performed in order to investigate the effects of substrate growth temperature and dopant species on deep levels in Si layers during low-temperature molecular beam epitaxial growth. The structures studied were n + -p junctions using B doping for the p layer and p + -n junctions using P doping for the n layer. While the density of hole traps H1 (0.38-0.41 eV) in the B-doped p layers showed a clear increase with decreasing growth temperature from 600 to 370 degree sign C, the electron trap density was relatively constant. Interestingly, the minority carrier electron traps E1 (0.42-0.45 eV) and E2 (0.257 eV), found in the B-doped p layers, are similar to the majority carrier electron traps E11 (0.48 eV) and E22 (0.269 eV) observed in P-doped n layers grown at 600 degree sign C. It is hypothesized that these dominating electron traps are associated with pure divacancy defects and are independent of the dopant species

First-principles study of the effects of halogen dopants on the properties of intergranular films in silicon nitride ceramics

International Nuclear Information System (INIS)

Painter, Gayle S.; Becher, Paul F.; Kleebe, H.-J.; Pezzotti, G.

2002-01-01

The nanoscale intergranular films that form in the sintering of ceramics often occur as adherent glassy phases separating the crystalline grains in the ceramic. Consequently, the properties of these films are often equal in importance to those of the constituent grains in determining the ceramic's properties. The measured characteristics of the silica-rich phase separating the crystalline grains in Si 3 N 4 and many other ceramics are so reproducible that SiO 2 has become a model system for studies of intergranular films (IGF's). Recently, the influence of fluorine and chlorine dopants in SiO 2 -rich IGF's in silicon nitride was precisely documented by experiment. Along with the expected similarities between the halogens, some dramatically contrasting effects were found. But the atomic-scale mechanisms distinguishing the effects F and Cl on IGF behavior have not been well understood. First-principles density functional calculations reported here provide a quantum-level description of how these dopant-host interactions affect the properties of IGF's, with specific modeling of F and Cl in the silica-rich IGF in silicon nitride. Calculations were carried out for the energetics, structural changes, and forces on the atoms making up a model cluster fragment of an SiO 2 intergranular film segment in silicon nitride with and without dopants. Results show that both anions participate in the breaking of bonds within the IGF, directly reducing the viscosity of the SiO 2 -rich film and promoting decohesion. Observed differences in the way fluorine and chlorine affect IGF behavior become understandable in terms of the relative stabilities of the halogens as they interact with Si atoms that have lost one if their oxygen bridges

Simultaneous enhancement of carrier mobility and concentration via tailoring of Al-chemical states in Al-ZnO thin films

Energy Technology Data Exchange (ETDEWEB)

Kumar, Manish, E-mail: manishk@skku.edu; Wen, Long; Sahu, Bibhuti B. [Center for Advance Plasma Surface Technology (CAPST), NU-SKKU Joint Institute for Plasma-Nano Materials (IPNM), School of Advanced Materials Science and Engineering, Sungkyunkwan University, Suwon-440746 (Korea, Republic of); Han, Jeon Geon [Center for Advance Plasma Surface Technology (CAPST), NU-SKKU Joint Institute for Plasma-Nano Materials (IPNM), School of Advanced Materials Science and Engineering, Sungkyunkwan University, Suwon-440746 (Korea, Republic of); Department of Industrial Engineering, Faculty of Engineering, Chiang Mai University, Chiang Mai-50200 (Thailand)

2015-06-15

Simultaneously achieving higher carriers concentration and mobility is a technical challenge against up-scaling the transparent-conductive performances of transparent-conductive oxides. Utilizing one order higher dense (∼1 × 10{sup 11} cm{sup −3}) plasmas (in comparison to the conventional direct current plasmas), highly c-axis oriented Al-doped ZnO films have been prepared with precise control over relative composition and chemical states of constituting elements. Tailoring of intrinsic (O vacancies) and extrinsic (ionic Al and zero-valent Al) dopants provide simultaneous enhancement in mobility and concentration of charge carriers. Room-temperature resistivity as low as 4.89 × 10{sup −4} Ω cm along the carrier concentration 5.6 × 10{sup 20} cm{sup −3} is obtained in 200 nm thick transparent films. Here, the control of atomic Al reduces the charge trapping at grain boundaries and subdues the effects of grain boundary scattering. A mechanism based on the correlation between electron-hole interaction and carrier mobility is proposed for degenerately doped wide band-gap semiconductors.

Highly concentrating Fresnel lenses

International Nuclear Information System (INIS)

Kritchman, E.M.; Friesem, A.A.; Yekutieli, G.

1979-01-01

A new type of concave Fresnel lens capable of concentrating solar radiation very near the ultimate concentration limit is considered. The differential equations that describe the lens are solved to provide computed solutions which are then checked by ray tracing techniques. The performance (efficiency and concentration) of the lens is investigated and compared to that of a flat Fresnel lens, showing that the new lens is preferable for concentrating solar radiation. (author)

Theoretical study of the local structures and the EPR parameters for RLNKB glasses with VO2+ and Cu2+ dopants

Science.gov (United States)

Ding, Chang-Chun; Wu, Shao-Yi; Wu, Li-Na; Zhang, Li-Juan; Peng, Li; Wu, Ming-He; Teng, Bao-Hua

2018-02-01

The electron paramagnetic resonance (EPR) parameters and local structures for impurities VO2+ and Cu2+ in RO-Li2O-Na2O-K2O-B2O3 (RLNKB; R = Zn, Mg, Sr and Ba) glasses are theoretically investigated by using the perturbation formulas of the EPR parameters for tetragonally compressed octahedral 3d1 and tetragonally elongated octahedral 3d9 clusters, respectively. The VO2+ and Cu2+ dopants are found to undergo the tetragonal compression (characterized by the negative relative distortion ratios ρ ≈ -3%, -0.98%, -1% and -0.8% for R = Zn, Mg, Sr and Ba) and elongation (characterized by the positive relative distortion ratios ρ ≈ 29%, 17%, 16% and 28%), respectively, due to the Jahn-Teller effect. Both dopants show similar overall decreasing trends of cubic field parameter Dq and covalency factor N with decreasing electronegativity of alkali earth cation R. The conventional optical basicities Λth and local optical basicities Λloc are calculated for both systems, and the local Λloc are higher for Cu2+ than for VO2+ in the same RLNKB glass, despite the opposite relationship for the conventional Λth. This point is supported by the weaker covalency or stronger ionicity for Cu2+ than VO2+ in the same RLNKB system, characterized by the larger N in the former. The above comparative analysis on the spectral and local structural properties would be helpful to understand structures and spectroscopic properties for the similar oxide glasses with transition-metal dopants of complementary electronic configurations.

Effect of Er{sub 2}O{sub 3} dopant on electrical and optical properties of potassium sodium niobate silicate glass-ceramics

Energy Technology Data Exchange (ETDEWEB)

Yongsiri, Ploypailin [Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Sirisoonthorn, Somnuk [National Metal and Materials Technology Center, Pathumthani 12120 (Thailand); Pengpat, Kamonpan, E-mail: kamonpan.p@cmu.ac.th [Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Materials Science Research Center, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand)

2015-09-15

Highlights: • The KNN–SiO{sub 2} doped Er{sub 2}O{sub 3} glass-ceramics was prepared by incorporation method. • High dielectric constant (458.41 at 100 kHz) and low loss (0.0005) could be obtained. • TEM and SEM confirmed the existence of KNN crystals embedded in glass matrix. • The Er{sub 2}O{sub 3} dopant causes insignificant effect on modifying E{sub g} value. - Abstract: In this study, transparent glass-ceramics from potassium sodium niobate (KNN)-silicate glass system doped with erbium oxide (Er{sub 2}O{sub 3}) were successfully prepared by incorporation method. KNN was added in glass batches as heterogeneous nucleating agent. The KNN powder was mixed with SiO{sub 2} and Er{sub 2}O{sub 3} dopant with KNN and Er{sub 2}O{sub 3} content varied between 70–80 and 0.5–1.0 mol%, respectively. Each batch was subsequently melted at 1300 °C for 15 min in a platinum crucible using an electric furnace. The quenched glasses were then subjected to heat treatment at various temperatures for 4 h. XRD results showed that the prepared glass ceramics contained crystals of KNN solid solution. In contrary, dielectric constant (ϵ{sub r}) and dielectric loss (tan δ) were found to increase with increasing heat treatment temperature. Additionally, optical properties such as absorbance and energy band gap have been investigated.

High yield and facile microwave-assisted synthesis of conductive H{sub 2}SO{sub 4} doped polyanilines

Energy Technology Data Exchange (ETDEWEB)

Gizdavic-Nikolaidis, Marija R., E-mail: m.gizdavic@auckland.ac.nz [School of Chemical Sciences, The University of Auckland, Private Bag 92019, Auckland Mail Centre, Auckland, 1142 (New Zealand); Faculty of Physical Chemistry, Studentski Trg 12-16, PO Box 137, 11001, Belgrade (Serbia); Jevremovic, Milutin M. [Public Company Nuclear Facilities of Serbia, 12-14 Mike Petrovica Alasa, Vinca, 11351, Belgrade (Serbia); Milenkovic, Maja [Faculty of Physical Chemistry, Studentski Trg 12-16, PO Box 137, 11001, Belgrade (Serbia); Allison, Morgan C. [School of Chemical Sciences, The University of Auckland, Private Bag 92019, Auckland Mail Centre, Auckland, 1142 (New Zealand); Stanisavljev, Dragomir R. [Faculty of Physical Chemistry, Studentski Trg 12-16, PO Box 137, 11001, Belgrade (Serbia); Bowmaker, Graham A. [School of Chemical Sciences, The University of Auckland, Private Bag 92019, Auckland Mail Centre, Auckland, 1142 (New Zealand); Zujovic, Zoran D. [School of Chemical Sciences, The University of Auckland, Private Bag 92019, Auckland Mail Centre, Auckland, 1142 (New Zealand); MacDiarmid Institute for Advanced Materials and Nanotechnology, Victoria University of Wellington, PO Box 600, Wellington, 6140 (New Zealand); Institute of General and Physical Chemistry, Studentski Trg 12-16, 11001, Belgrade (Serbia)

2016-04-15

The microwave-assisted synthesis of polyaniline (PANI) was performed using ammonium persulphate (APS) as oxidizing agent in 0.5 M–2.5 M concentration range of aqueous sulphuric acid (H{sub 2}SO{sub 4}) at 93 W applied microwave power of 10 min duration. The microwave (MW) synthesized PANIs had 3 times higher yield in comparison to PANI samples prepared using a classical method, CS (0 W MW power) at the same temperature for 10 min synthesis duration period. Fourier Transform Infrared (FTIR) and UV–Vis spectroscopies confirmed the formation of PANI structure in all products. The influence of H{sub 2}SO{sub 4} acid dopant on the spin concentration of MW and CS H{sub 2}SO{sub 4} doped PANI samples were examined by EPR spectroscopy, while the morphological characteristics were investigated by using scanning electron microscopy (SEM). XRD results showed amorphous phases in both MW and CS H{sub 2}SO{sub 4} doped PANI samples. Conductivity measurements revealed ∼1.5 times higher conductivity values for MW H{sub 2}SO{sub 4} doped PANI samples in comparison with PANI samples prepared by the CS method under same condition. The influence of sulfate anion in comparison to chloride anion as a dopant on morphological, dopant levels and conductivity properties of MW PANI samples were also investigated. - Highlights: • Nanoporous microwave synthesized doped polyanilines as chemical sensor material. • Morphology and physical properties of polyanilines depend on acid concentration. • Spin concentration is determined by the nature of the polyaniline synthesis.

High Quality Zinc Oxide Thin films and Nanostructures Prepared by Pulsed Laser Deposition for Photodetectors

KAUST Repository

Flemban, Tahani H.

2017-01-01

is attributed to defect/impurity bands mediated by Gd dopants. In this dissertation, I study the effects of Gd concentration, oxygen pressure using pulsed laser deposition (PLD), and thermal annealing on the optical and structural properties of undoped and Gd

Ultra flat ideal concentrators of high concentration

Energy Technology Data Exchange (ETDEWEB)

Chaves, Julio [IST, Physics Dept., Lisboa (Portugal); INETI-DER, Lisboa (Portugal); Collares-Pereira, Manuel [INETI-DER, Lisboa (Portugal)

2000-07-01

A new method for the design of nonimaging devices is presented. Its application to the design of ultra flat compact concentrators is analysed. These new concentrators are based on a combination of two stages: the first one is composed of a large number of small structures placed side by side and the second one is a very compact single device concentrating the radiation to the limit. These devices are ideal for 2D. These compact designs are much more compact than the traditional ones like lens-mirror combinations or parabolic primaries with nonimaging secondaries. Besides, they can be designed for any acceptance angle, while the traditional ones are limited to small acceptance angles. (Author)

Compensation of native donor doping in ScN: Carrier concentration control and p-type ScN

Science.gov (United States)

Saha, Bivas; Garbrecht, Magnus; Perez-Taborda, Jaime A.; Fawey, Mohammed H.; Koh, Yee Rui; Shakouri, Ali; Martin-Gonzalez, Marisol; Hultman, Lars; Sands, Timothy D.

2017-06-01

Scandium nitride (ScN) is an emerging indirect bandgap rocksalt semiconductor that has attracted significant attention in recent years for its potential applications in thermoelectric energy conversion devices, as a semiconducting component in epitaxial metal/semiconductor superlattices and as a substrate material for high quality GaN growth. Due to the presence of oxygen impurities and native defects such as nitrogen vacancies, sputter-deposited ScN thin-films are highly degenerate n-type semiconductors with carrier concentrations in the (1-6) × 1020 cm-3 range. In this letter, we show that magnesium nitride (MgxNy) acts as an efficient hole dopant in ScN and reduces the n-type carrier concentration, turning ScN into a p-type semiconductor at high doping levels. Employing a combination of high-resolution X-ray diffraction, transmission electron microscopy, and room temperature optical and temperature dependent electrical measurements, we demonstrate that p-type Sc1-xMgxN thin-film alloys (a) are substitutional solid solutions without MgxNy precipitation, phase segregation, or secondary phase formation within the studied compositional region, (b) exhibit a maximum hole-concentration of 2.2 × 1020 cm-3 and a hole mobility of 21 cm2/Vs, (c) do not show any defect states inside the direct gap of ScN, thus retaining their basic electronic structure, and (d) exhibit alloy scattering dominating hole conduction at high temperatures. These results demonstrate MgxNy doped p-type ScN and compare well with our previous reports on p-type ScN with manganese nitride (MnxNy) doping.

Technical report Development of a piezoelectric inkjet dopant delivery device for an atmospheric pressure photoionization source with liquid chromatography/mass spectrometry

KAUST Repository

Amad, Maan H.; Li, Erqiang; Sioud, Salim; Thoroddsen, Sigurdur T

2013-01-01

mixture consisting of 18 different polycyclic aromatic hydrocarbons (PAHs) The results show that the new system works robustly at low dopant consumption level (16 uL min-1) consuming only approximately 5% of the amount used by conventional sources The low

Electron transport investigation of layered MoO3 oxides doped with different concentrations of Nb2O5 oxide

International Nuclear Information System (INIS)

Al-Khawaja, S.; Kasem, M.

2008-07-01

The dc and ac electric conductivity has been studied for numerous samples of molybdenum oxide MoO 3 doped with niobium oxide Nb 2 O 5 elaborated via the solid state reactions. By means of the electric resistivity and dielectricity curves obtained as a function of temperature, and according to the dopant concentration, the behaviour of these compounds has been allocated. Most of the investigated samples, which are insulating at room temperature, have been witnessed to exhibit simultaneously two different electric comportments; metallic and semiconducting within the range of low and high temperatures respectively, designated by a critical temperature related to the nature of the material. Both of these behaviours are attributed electronically to ionic conduction mechanism, occurring in the solid material formed upon doping with Nb 2 O 5 , which is utterly diffused into the layered structure of MoO 3 particularly for x≥40% concentrations and accompanied by relaxation in the dielectric function between 5 Hz and 13 M Hz.(Authors)

Influence of dopant segregation on the work function and electrical properties of Ge-doped in comparison to Sn-doped In{sub 2}O{sub 3} thin films

Energy Technology Data Exchange (ETDEWEB)

Hoyer, Karoline L.; Hubmann, Andreas H.; Klein, Andreas [Surface Science Division, Institute of Materials Science, Technische Universitaet Darmstadt (Germany)

2017-02-15

Ge-doped In{sub 2}O{sub 3} thin films prepared by magnetron sputtering are studied using photoelectron spectroscopy and Hall effect measurements. Carrier conductivities of up to 8.35 x 10{sup 3} S cm{sup -1} and carrier mobilities of up to 57 cm{sup 2} V{sup -1}s{sup -1} are observed. The surface Ge concentration is enhanced by a factor of 2-3 compared to the concentration in the interior of the films. The surface Ge concentration increases with more oxidizing deposition conditions, in opposite to what has been reported for Sn-doped In{sub 2}O{sub 3}. Ge-doped In{sub 2}O{sub 3} films exhibit higher work functions as compared to Sn-doped films, in particular at oxidizing conditions. This is attributed to the formation of a GeO{sub 2} surface phase. While segregation of Sn reduces the carrier mobility due to grain boundary scattering, Ge segregation does not show such an effect. The differences are attributed to the different oxidation states of the segregated dopants, in agreement with the observed dependence of segregation on oxygen activity. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Substitutional Co dopant on the GaAs(110) surface: A first principles study

Energy Technology Data Exchange (ETDEWEB)

Fang, Zhou; Yi, Zhijun, E-mail: zhijunyi@cumt.edu.cn

2016-12-01

Using the first principles ground state method, the electronic properties of single Co dopant replacing one Ga atom on the GaAs(110) surface are studied. Our calculated local density of states (LDOS) at Co site presents several distinct peaks above the valence band maximum (VBM), and this agrees with recent experiments. Moreover, the calculated STM images at bias voltages of 2 eV and −2 eV also agree with experiments. We discussed the origin of Co impurity induced distinct peaks, which can be characterized with the hybridization between Co d orbitals and p-like orbitals of surface As and Ga atoms.

Feasibility of using a high power CO2 laser as an alternative source to test high heat load x-ray optics

International Nuclear Information System (INIS)

Fernandez, P.B.

1993-01-01

To determine the feasibility of using the CO 2 laser at LAL as an alternative heat source for x-ray optics tests, we have studied the absorption of the 10.6-micron laser light in silicon for two different dopant concentrations, using the resistivity as a predictor for the absorption length. We describe the results from these tests in this report

Atmospheric conditions during high ragweed pollen concentrations in Zagreb, Croatia

Science.gov (United States)

Prtenjak, Maja Telišman; Srnec, Lidija; Peternel, Renata; Madžarević, Valentina; Hrga, Ivana; Stjepanović, Barbara

2012-11-01

We examined the atmospheric conditions favourable to the occurrence of maximum concentrations of ragweed pollen with an extremely high risk of producing allergy. Over the 2002-2009 period, daily pollen data collected in Zagreb were used to identify two periods of high pollen concentration (> 600 grains/m3) for our analysis: period A (3-4 September 2002) and period B (6-7 September 2003). Synoptic conditions in both periods were very similar: Croatia was under the influence of a lower sector high pressure system moving slowly eastward over Eastern Europe. During the 2002-2009 period, this type of weather pattern (on ~ 70% of days), in conjunction with almost non-gradient surface pressure conditions in the area (on ~ 30% of days) characterised days when the daily pollen concentrations were higher than 400 grains/m3. Numerical experiments using a mesoscale model at fine resolution showed successful multi-day simulations reproducing the local topographic influence on wind flow and in reasonable agreement with available observations. According to the model, the relatively weak synoptic flow (predominantly from the eastern direction) allowed local thermal circulations to develop over Zagreb during both high pollen episodes. Two-hour pollen concentrations and 48-h back-trajectories indicated that regional-range transport of pollen grains from the central Pannonian Plain was the cause of the high pollen concentrations during period A. During period B, the north-westward regional-range transport in Zagreb was supplemented significantly by pronounced horizontal recirculation of pollen grains. This recirculation happened within the diurnal local circulation over the city, causing a late-evening increase in pollen concentration.

Efficacy of high iodine concentration contrast medium with saline pushing in hepatic CT in patients with chronic liver disease. Comparison of high doses-standard contrast medium concentration

International Nuclear Information System (INIS)

Matoba, Munetaka; Kondo, Tamaki; Nishikawa, Takahiro; Kuginuki, Yasuaki; Yokota, Hajime; Higashi, Kotaro; Tonami, Hisao

2006-01-01

The aim of this study was to compare the enhancement of liver parenchyama with high iodine concentration contrast medium with saline pushing to that with high doses standard iodine concentration in hepatic CT in patients with chronic liver disease. There was no statistically significant difference regarding to the enhancement of liver parenchyama between the 370 mgI/ml of contrast medium with saline pushing and high doses standard iodine concentration contrast medium. (author)

Use of p- and n-type vapor phase doping and sub-melt laser anneal for extension junctions in sub-32 nm CMOS technology

Energy Technology Data Exchange (ETDEWEB)

Nguyen, N.D., E-mail: Duy.Nguyen@imec.b [IMEC, Kapeldreef 75, B-3001 Leuven (Belgium); Rosseel, E. [IMEC, Kapeldreef 75, B-3001 Leuven (Belgium); Takeuchi, S. [IMEC, Kapeldreef 75, B-3001 Leuven (Belgium); Department of Physics and Astronomy, KU Leuven, B-3001 Leuven (Belgium); Everaert, J.-L. [IMEC, Kapeldreef 75, B-3001 Leuven (Belgium); Yang, L. [IMEC, Kapeldreef 75, B-3001 Leuven (Belgium); Department of Chemistry and INPAC Institute, KU Leuven, B-3001 Leuven (Belgium); Goossens, J.; Moussa, A.; Clarysse, T.; Richard, O.; Bender, H. [IMEC, Kapeldreef 75, B-3001 Leuven (Belgium); Zaima, S. [Department of Crystalline Materials Science, Graduate School of Engineering, Nagoya University, Furo-cho, Nagoya, 464-8603 (Japan); Sakai, A. [Department of System Innovation, Graduate School of Engineering Science, Osaka University, 1-3 Machikaneyama-cho, Toyonaka, Osaka 560-8531 (Japan); Loo, R. [IMEC, Kapeldreef 75, B-3001 Leuven (Belgium); Lin, J.C. [TSMC, R and D, 8, Li-Hsin 6th Rd., Hsinchu Science-Based Park, Hsinchu, Taiwan (China); TSMC assignee at IMEC, Kapeldreef 75, B-3001 Leuven (Belgium); Vandervorst, W. [IMEC, Kapeldreef 75, B-3001 Leuven (Belgium); Instituut voor Kern- en Stralingsfysika - IKS, KU Leuven, B-3001 Leuven (Belgium); Caymax, M. [IMEC, Kapeldreef 75, B-3001 Leuven (Belgium)

2010-01-01

We evaluated the combination of vapor phase doping and sub-melt laser anneal as a novel doping strategy for the fabrication of source and drain extension junctions in sub-32 nm CMOS technology, aiming at both planar and non-planar device applications. High quality ultra shallow junctions with abrupt profiles in Si substrates were demonstrated on 300 mm Si substrates. The excellent results obtained for the sheet resistance and the junction depth with boron allowed us to fulfill the requirements for the 32 nm as well as for the 22 nm technology nodes in the PMOS case by choosing appropriate laser anneal conditions. For instance, using 3 laser scans at 1300 {sup o}C, we measured an active dopant concentration of about 2.1 x 10{sup 20} cm{sup -} {sup 3} and a junction depth of 12 nm. With arsenic for NMOS, ultra shallow junctions were achieved as well. However, as also seen for other junction fabrication schemes, low dopant activation level and active dose (in the range of 1-4 x 10{sup 13} cm{sup -} {sup 2}) were observed although dopant concentration versus depth profiles indicate that the dopant atoms were properly driven into the substrate during the anneal step. The electrical deactivation of a large part of the in-diffused dopants was responsible for the high sheet resistance values.

Use of p- and n-type vapor phase doping and sub-melt laser anneal for extension junctions in sub-32 nm CMOS technology

International Nuclear Information System (INIS)

Nguyen, N.D.; Rosseel, E.; Takeuchi, S.; Everaert, J.-L.; Yang, L.; Goossens, J.; Moussa, A.; Clarysse, T.; Richard, O.; Bender, H.; Zaima, S.; Sakai, A.; Loo, R.; Lin, J.C.; Vandervorst, W.; Caymax, M.

2010-01-01

We evaluated the combination of vapor phase doping and sub-melt laser anneal as a novel doping strategy for the fabrication of source and drain extension junctions in sub-32 nm CMOS technology, aiming at both planar and non-planar device applications. High quality ultra shallow junctions with abrupt profiles in Si substrates were demonstrated on 300 mm Si substrates. The excellent results obtained for the sheet resistance and the junction depth with boron allowed us to fulfill the requirements for the 32 nm as well as for the 22 nm technology nodes in the PMOS case by choosing appropriate laser anneal conditions. For instance, using 3 laser scans at 1300 o C, we measured an active dopant concentration of about 2.1 x 10 20 cm - 3 and a junction depth of 12 nm. With arsenic for NMOS, ultra shallow junctions were achieved as well. However, as also seen for other junction fabrication schemes, low dopant activation level and active dose (in the range of 1-4 x 10 13 cm - 2 ) were observed although dopant concentration versus depth profiles indicate that the dopant atoms were properly driven into the substrate during the anneal step. The electrical deactivation of a large part of the in-diffused dopants was responsible for the high sheet resistance values.

Study on high concentration solar concentrator using a Fresnel lens with a secondary concentrator; Fresnel lens to niji shukokei wo mochiita solar chemistry yo kobairitsu shukokei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Aihara, T; Suzuki, A; Fujibayashi, K [Tokyo University of Agriculture and Technology, Tokyo (Japan)

1997-11-25

A high concentration light collection system for solar chemistry was devised by using an inexpensive Fresnel lens in a primary concentration system and a conical type concentrator in a secondary concentration system. A Fresnel lens alone would not achieve sufficiently high light collecting magnification to attain high temperatures because of restrictions in the opening angle as seen from a focus. Therefore, a secondary concentration system was installed on a focus for an attempt of stopping. Reflection plane of a three-dimensional compound parabolic concentrator (CPC) is a rotary parabolic plane, whose process is expensive because of its surface processing accuracy. Therefore, a conical type concentrator was employed as a secondary concentration system. This system may not be capable of achieving as high concentration as in the CPC, but its shape is simple and it is inexpensive. In its optimization, a complete black body surface placed in vacuum atmosphere was hypothesized as a light concentrating part for the secondary concentration system to calculate heat collecting efficiencies at respective temperature settings. Using simultaneously the secondary concentration system, rather than collecting heat by using a Fresnel lens alone, has attained as high value as from 5.99% (500 degC) to 43.47% (1400 degC). Economical high-temperature heat collection of solar chemistry level may be possible by using a Fresnel lens and a conical secondary concentration system. 1 ref., 7 figs., 2 tabs.

Role of dopant in annealing of chemical radiation damage in potassium nitrate

International Nuclear Information System (INIS)

Mohapatra, B.M.; Bhatta, D.

1984-01-01

The role of cationic vacancy in th annealing of gamma-irradiated potassium nitrate has been investigated using Ba 2+ as a dopant. Isothermal annealing data show that the pure potassium nitrate is immune to annealing above and below the temperature of crystal transition 127degC (Rhombic↔tTrigonal), while the doped crystals undergo recovery by a combination of one first order and one second order process above the phase change and by a second order process below this temperature. The recovery process above 127degC is initially fast (upto 1 hr) but subsequently it slows down to a pseudo-plateau. The proportion of damage which recombines by first and second order processes is 40.6 and 59.4 respectively. (author)

Large area high quality silicon detectors for scientific research and radioactivity monitoring in the environment

International Nuclear Information System (INIS)

Frolov, D.; Perevertailo, V.; Frolov, O.; Kononenko, Yu.; Pugatch, V.; Rozenfeld, A.

1995-01-01

Full text: Investigation of detector and special test structures made on detector wafers was carried out. Si wafer with a diameter of 76 mm, n-type, specific resistance 2-6 kΩ·cm, made of Si produced at a titanium-magnesium factory in Zaporozh'e (Ukraine) were used. C-V curves were measured on p + -n-junctions of various areas (0.1 cm 2 to 20 cm 2 ) and various configuration. In coordinated C 3 (dC/dV) -1 vs V initial parts of the curves are horizontal lines, that indicates a uniform dopant concentration into the depth of a sample, while starting with some voltage a rise is observed associated with full depletion of the sample. However this rise is more smooth then one described by a simple model. The smooth rise is due to non-uniformity of the depletion depth over the p + -n-junction area caused by non-uniform distribution of dopant concentration over the wafer surface. As a results, full depletion doesn't occur simultaneously in all regions of the junction and is stretched along the voltage scale. A theory is developed to define a distribution of the sample areas over full depletion voltage V fd or over dopant concentration N and, given a fixed voltage, to define the distribution of non-depleted junction ares over a thickness of non-depleted area. Results show possibility of non uniform N and, correspondingly, V fd by up to 2 times with big junction sizes. A high level of non-uniformity was observed not only on Si made in Zaporozh'e, but also on Wacker Si. This method of measurements and analysis may be helpful both in working with detectors and detector Si quality control. Measurements of current and capacitance in a gate-controlled junction (a MOS structure partially overlapped with a p + -n-junction) allowed division of surface into the depth of the crystal. Some peculiarities are observed in current curves compared to previous reports associated with low dopant concentration in our experiments. Local defect areas near the p-n-junction encouraging avalanche

Highly efficient red OLEDs using DCJTB as the dopant and delayed fluorescent exciplex as the host.

Science.gov (United States)

Zhao, Bo; Zhang, Tianyou; Chu, Bei; Li, Wenlian; Su, Zisheng; Wu, Hairuo; Yan, Xingwu; Jin, Fangming; Gao, Yuan; Liu, Chengyuan

2015-05-29

In this manuscript, we demonstrated a highly efficient DCJTB emission with delayed fluorescent exciplex TCTA:3P-T2T as the host. For the 1.0% DCJTB doped concentration, a maximum luminance, current efficiency, power efficiency and EQE of 22,767 cd m(-2), 22.7 cd A(-1), 21.5 lm W(-1) and 10.15% were achieved, respectively. The device performance is the best compared to either red OLEDs with traditional fluorescent emitter or traditional red phosphor of Ir(piq)3 doped into CBP host. The extraction of so high efficiency can be explained as the efficient triplet excitons up-conversion of TCTA:3P-T2T and the energy transfer from exciplex host singlet state to DCJTB singlet state.

Semiempirical and DFT computations of the influence of Tb(III) dopant on unit cell dimensions of cerium(III) fluoride.

Science.gov (United States)

Shyichuk, Andrii; Runowski, Marcin; Lis, Stefan; Kaczkowski, Jakub; Jezierski, Andrzej

2015-01-30

Several computational methods, both semiempirical and ab initio, were used to study the influence of the amount of dopant on crystal cell dimensions of CeF3 doped with Tb(3+) ions (CeF3 :Tb(3+) ). AM1, RM1, PM3, PM6, and PM7 semiempirical parameterization models were used, while the Sparkle model was used to represent the lanthanide cations in all cases. Ab initio calculations were performed by means of GGA+U/PBE projector augmented wave density functional theory. The computational results agree well with the experimental data. According to both computation and experiment, the crystal cell parameters undergo a linear decrease with increasing amount of the dopant. The computations performed using Sparkle/PM3 and DFT methods resulted in the best agreement with the experiment with the average deviation of about 1% in both cases. Typical Sparkle/PM3 computation on a 2×2×2 supercell of CeF3:Tb3+ lasted about two orders of magnitude shorter than the DFT computation concerning a unit cell of this material. © 2014 Wiley Periodicals, Inc.

High concentration suspended sediment measurments using acontinuous fiber optic in-stream transmissometer

Energy Technology Data Exchange (ETDEWEB)

Campbell, Chris G.; Laycak, Danny T.; Hoppes, William; Tran,Nguyen T.; Shi, Frank G.

2004-05-26

Suspended sediment loads mobilized during high flow periods in rivers and streams are largely uncharacterized. In smaller and intermittent streams, a large storm may transport a majority of the annual sediment budget. Therefore monitoring techniques that can measure high suspended sediment concentrations at semi-continuous time intervals are needed. A Fiber optic In-stream Transmissometer (FIT) is presented for continuous measurement of high concentration suspended sediment in storm runoff. FIT performance and precision were demonstrated to be reasonably good for suspended sediment concentrations up to 10g/L. The FIT was compared to two commercially available turbidity devices and provided better precision and accuracy at both high and low concentrations. Both turbidity devices were unable to collect measurements at concentrations greater than 4 g/L. The FIT and turbidity measurements were sensitive to sediment particle size. Particle size dependence of transmittance and turbidity measurement poses the greatest problem for calibration to suspended sediment concentration. While the FIT was demonstrated to provide acceptable measurements of high suspended sediment concentrations, approaches to real-time suspended sediment detection need to address the particle size dependence in concentration measurements.

Intrinsic and extrinsic diffusion of phosphorus, arsenic, and antimony in germanium

International Nuclear Information System (INIS)

Brotzmann, Sergej; Bracht, Hartmut

2008-01-01

Diffusion experiments of phosphorus (P), arsenic (As), and antimony (Sb) in high purity germanium (Ge) were performed at temperatures between 600 and 920 deg. C. Secondary ion mass spectrometry and spreading resistance profiling were applied to determine the concentration profiles of the chemically and electrically active dopants. Intrinsic and extrinsic doping conditions result in a complementary error function and box-shaped diffusion profiles, respectively. These profiles demonstrate enhanced dopant diffusion under extrinsic doping. Accurate modeling of dopant diffusion is achieved on the basis of the vacancy mechanism taking into account singly negatively charged dopant-vacancy pairs and doubly negatively charged vacancies. The activation enthalpy and pre-exponential factor for dopant diffusion under intrinsic condition were determined to 2.85 eV and 9.1 cm 2 s -1 for P, 2.71 eV and 32 cm 2 s -1 for As, and 2.55 eV and 16.7 cm 2 s -1 for Sb. With increasing atomic size of the dopants the activation enthalpy decreases. This is attributed to differences in the binding energy of the dopant-vacancy pairs

Cellulase Inhibition by High Concentrations of Monosaccharides

DEFF Research Database (Denmark)

Hsieh, Chia-Wen; Cannella, David; Jørgensen, Henning

2014-01-01

Biological degradation of biomass on an industrial scale culminates in high concentrations of end products. It is known that the accumulation of glucose and cellobiose, end products of hydrolysis, inhibit cellulases and decrease glucose yields. Aside from these end products, however, other monosa...

Multiphysics modelling and experimental validation of high concentration photovoltaic modules

International Nuclear Information System (INIS)

Theristis, Marios; Fernández, Eduardo F.; Sumner, Mike; O'Donovan, Tadhg S.

2017-01-01

Highlights: • A multiphysics modelling approach for concentrating photovoltaics was developed. • An experimental campaign was conducted to validate the models. • The experimental results were in good agreement with the models. • The multiphysics modelling allows the concentrator’s optimisation. - Abstract: High concentration photovoltaics, equipped with high efficiency multijunction solar cells, have great potential in achieving cost-effective and clean electricity generation at utility scale. Such systems are more complex compared to conventional photovoltaics because of the multiphysics effect that is present. Modelling the power output of such systems is therefore crucial for their further market penetration. Following this line, a multiphysics modelling procedure for high concentration photovoltaics is presented in this work. It combines an open source spectral model, a single diode electrical model and a three-dimensional finite element thermal model. In order to validate the models and the multiphysics modelling procedure against actual data, an outdoor experimental campaign was conducted in Albuquerque, New Mexico using a high concentration photovoltaic monomodule that is thoroughly described in terms of its geometry and materials. The experimental results were in good agreement (within 2.7%) with the predicted maximum power point. This multiphysics approach is relatively more complex when compared to empirical models, but besides the overall performance prediction it can also provide better understanding of the physics involved in the conversion of solar irradiance into electricity. It can therefore be used for the design and optimisation of high concentration photovoltaic modules.

Effect of Low Concentration Sn Doping on Optical Properties of CdS Films Grown by CBD Technique

Directory of Open Access Journals (Sweden)

Mohd Sabri Mohd Ghazali

2011-09-01

Full Text Available Thin and transparent films of doped cadmium sulfide (CdS were obtained on commercial glass substrates by Chemical Bath Deposition (CBD technique. The films were doped with low concentration of Sn, and annealed in air at 300 °C for 45 min. The morphological characterization of the films with different amounts of dopant was made using SEM and EDAX analysis. Optical properties of the films were evaluated by measuring transmittance using the UV-vis spectrophotometer. A comparison of the results revealed that lower concentration of Sn doping improves transmittance of CdS films and makes them suitable for application as window layer of CdTe/CIGS solar cells.

Hydrogen Storage Properties of Lithium Aluminohydride Modified by Dopants and Mechanochemistry

Energy Technology Data Exchange (ETDEWEB)

Hosokawa, Ketia [Iowa State Univ., Ames, IA (United States)

2002-01-01

Alkali metal aluminohydrides have high potential as solid hydrogen storage materials. They have been known for their irreversible dehydrogenation process below 100 atm until Bogdanovic et al succeeded in the re-hydrogenation of NaAlH₄ below 70 atm. They achieved 4 wt.% H₂ reversible capacity by doping NaAlH₄ with Ti and/or Fe organo-metallic compounds as catalysts. This suggests that other alkali and, possibly alkaline earth metal aluminohydrides can be used for reversible hydrogen storage when modified by proper dopants. In this research, Zr₂₇Ti₉Ni₃₈V₅Mn₁₆Cr₅, LaNi _4.85Sn_0.15, Al₃Ti, and PdCl₂ were combined with LiAlH₄ by ball-milling to study whether or not LiAlH₄ is capable to both absorb and desorb hydrogen near ambient conditions. X-ray powder diffraction, differential thermal analysis, and scanning electron microscopy were employed for sample characterizations. All four compounds worked as catalysts in the dehydrogenation reactions of both LiAlH₄ and Li₃AlH₆ by inducing the decomposition at lower temperature. However, none of them was applicable as catalyst in the reverse hydrogenation reaction at low to moderate hydrogen pressure.

Electron-beam-induced reactivation of Si dopants in hydrogenated two-dimensional AlGaAs heterostructures: a possible new route for III-V nanostructure fabrication

International Nuclear Information System (INIS)

Kurowski, Ludovic; Bernard, Dorothee; Constant, Eugene; Decoster, Didier

2004-01-01

Hydrogen incorporation in n-type Si-doped GaAs epilayers is a well-known process which leads to the neutralization of the active Si impurities with the formation of SiH complexes. Recently, we have shown that SiH complex dissociation and, consequently, Si-dopant reactivation could occur when the epilayers are exposed to an electron beam. Two epilayers have been studied: the first is a 0.35 μm thick hydrogenated Si-doped GaAs epilayer and the second is Si planar-doped AlGaAs/GaAs/InGaAs heterostructures. Firstly, Hall effect measurements have been carried out on the epilayers exposed, after RF hydrogen plasma exposition, to increasing electron doses with different injection energies. For the 2D heterostructures, we have observed that the free carrier density N s does not vary significantly for weak electron densities. This reactivation presents a threshold value, contrary to the 0.35 μm epilayer in which N s varies quite linearly. It will be shown that such phenomena might be attributed to the filling of surface states as the dopants are progressively reactivated. Then, using a high spatial resolution electron beam lithography system, nanometric conductive patterns have been fabricated starting from hydrogenated epilayers. Electric measurements have been performed and the results obtained show that about 15 nm spatial resolution could be expected. In conclusion, taking into account this spatial resolution, the high spatial contrast of conductivity which could be expected due to the existence of an electron dose threshold, and the high mobility of the AlGaAs/GaAs/InGaAs heterostructure, the effects described in this paper could open a new way for the fabrication of III-V 1D or 2D mesoscopic structures for electronic or optoelectronic applications

Structural and optical properties of vanadium doped SnO{sub 2} nanoparticles with high photocatalytic activities

Energy Technology Data Exchange (ETDEWEB)

Reddy, Ch. Venkata [School of Mechanical Engineering, Yeungnam University, Gyeongsan 712-749 (Korea, Republic of); Babu, B. [Department of Electronics and Computer Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of); Vattikuti, S.V. Prabhakar [School of Mechanical Engineering, Yeungnam University, Gyeongsan 712-749 (Korea, Republic of); Ravikumar, R.V.S.S.N. [Department of Physics, Acharya Nagarjuna University, Guntur, A.P. 522510 (India); Shim, Jaesool, E-mail: Jshim@ynu.ac.kr [School of Mechanical Engineering, Yeungnam University, Gyeongsan 712-749 (Korea, Republic of)

2016-11-15

Vanadium (0.01, 0.03 and 0.05 mol%) doped SnO{sub 2} nanoparticles have been synthesized using combustion synthesis method. The as-prepared nanoparticles were characterized using various measurements such as XRD, SEM with EDS, HRTEM, Raman spectroscopy, optical, PL, XPS and FT-IR techniques. The crystal structure and average particle sizes of the prepared nanoparticles were confirmed from the XRD. The average crystalline particle sizes were decreased by increasing the vanadium dopant concentration. The presence of vanadium as V{sup 4+} species in the host lattice was confirmed by X-ray photoelectron spectroscopy. The band gap energies were decreased by increasing dopant concentration. The 0.05 mol% doped sample showed higher photocatalytic activity than undoped, V-1 and V-3 in decomposing rhodamine B (RhB) under UV light irradiation. The Raman and IR spectra confirm the fundamental vibration of SnO{sub 2} host molecules.

Enhanced n-Doping Efficiency of a Naphthalenediimide-Based Copolymer through Polar Side Chains for Organic Thermoelectrics

KAUST Repository

Kiefer, David

2018-01-05

N-doping of conjugated polymers either requires a high dopant fraction or yields a low electrical conductivity because of their poor compatibility with molecular dopants. We explore n-doping of the polar naphthalenediimide–bithiophene copolymer p(gNDI-gT2) that carries oligoethylene glycol-based side chains and show that the polymer displays superior miscibility with the benzimidazole–dimethylbenzenamine-based n-dopant N-DMBI. The good compatibility of p(gNDI-gT2) and N-DMBI results in a relatively high doping efficiency of 13% for n-dopants, which leads to a high electrical conductivity of more than 10–1 S cm–1 for a dopant concentration of only 10 mol % when measured in an inert atmosphere. We find that the doped polymer is able to maintain its electrical conductivity for about 20 min when exposed to air and recovers rapidly when returned to a nitrogen atmosphere. Overall, solution coprocessing of p(gNDI-gT2) and N-DMBI results in a larger thermoelectric power factor of up to 0.4 μW K–2 m–1 compared to other NDI-based polymers.

Complete doping in solid-state by silica-supported perchloric acid as dopant solid acid: Synthesis and characterization of the novel chiral composite of poly [(±)-2-(sec-butyl) aniline

Energy Technology Data Exchange (ETDEWEB)

Farrokhzadeh, Abdolkarim; Modarresi-Alam, Ali Reza, E-mail: modaresi@chem.usb.ac.ir

2016-05-15

Poly [(±)-2-(sec-butyl) aniline]/silica-supported perchloric acid composites were synthesized by combination of poly[(±)-2-sec-butylaniline] base (PSBA) and the silica-supported perchloric acid (SSPA) as dopant solid acid in solid-state. The X-ray photoelectron spectroscopy (XPS) and CHNS results confirm nigraniline oxidation state and complete doping for composites (about 75%) and non-complete for the PSBA·HCl salt (about 49%). The conductivity of samples was (≈0.07 S/cm) in agreement with the percent of doping obtained of the XPS analysis. Also, contact resistance was determined by circular-TLM measurement. The morphology of samples by the scanning electron microscopy (SEM) and their coating were investigated by XPS, SEM-map and energy-dispersive X-ray spectroscopy (EDX). The key benefits of this work are the preparation of conductive chiral composite with the delocalized polaron structure under green chemistry and solid-state condition, the improvement of the processability by inclusion of the 2-sec-butyl group and the use of dopant solid acid (SSPA) as dopant. - Highlights: • The solid-state synthesis of the novel chiral composites of poly[(±)-2-(sec-butyl)aniline] (PSBA) and silica-supported perchloric acid (SSPA). • It takes 120 h for complete deprotonation of PSBA.HCl salt. • Use of SSPA as dopant solid acid for the first time to attain the complete doping of PSBA. • The coating of silica surface with PSBA.

Differences in Swallowing between High and Low Concentration Taste Stimuli

Directory of Open Access Journals (Sweden)

Ahmed Nagy

2014-01-01

Full Text Available Taste is a property that is thought to potentially modulate swallowing behavior. Whether such effects depend on taste, intensity remains unclear. This study explored differences in the amplitudes of tongue-palate pressures in swallowing as a function of taste stimulus concentration. Tongue-palate pressures were collected in 80 healthy women, in two age groups (under 40, over 60, stratified by genetic taste status (nontasters, supertasters. Liquids with different taste qualities (sweet, sour, salty, and bitter were presented in high and low concentrations. General labeled magnitude scale ratings captured perceived taste intensity and liking/disliking of the test liquids. Path analysis explored whether factors of taste, concentration, age group, and/or genetic taste status impacted: (1 perceived intensity; (2 palatability; and (3 swallowing pressures. Higher ratings of perceived intensity were found in supertasters and with higher concentrations, which were more liked/disliked than lower concentrations. Sweet stimuli were more palatable than sour, salty, or bitter stimuli. Higher concentrations elicited stronger tongue-palate pressures independently and in association with intensity ratings. The perceived intensity of a taste stimulus varies as a function of stimulus concentration, taste quality, participant age, and genetic taste status and influences swallowing pressure amplitudes. High-concentration salty and sour stimuli elicit the greatest tongue-palate pressures.

Enhancement of thermoelectric properties of Mg2Si compounds with Bi doping through carrier concentration tuning

Science.gov (United States)

Lee, Ji Eun; Cho, Sang-Hum; Oh, Min-Wook; Ryu, Byungi; Joo, Sung-Jae; Kim, Bong-Seo; Min, Bok-Ki; Lee, Hee-Woong; Park, Su-Dong

2014-07-01

The Bi-doped Mg2Si powder was fabricated with solid state reaction method and consolidated with hot pressing method and then its thermoelectric properties were investigated. The n-type transport properties were measured in all samples and temperature dependence of the electrical properties shows a behavior of degenerate semiconductors for Bi-doped samples. The electrical resistivity and the Seebeck coefficient were greatly reduced with Bi, which was mainly due to the increment of the carrier concentration. The samples have maximum carrier concentration of 8.2 × 1018 cm-3. The largest ZT value of 0.61 was achieve at 873 K for Mg2.04SiBi0.02. The Bi-doping was found to be an effective n-type dopant to adjust carrier concentration. [Figure not available: see fulltext.

High pressure inertial focusing for separating and concentrating bacteria at high throughput

Science.gov (United States)

Cruz, J.; Hooshmand Zadeh, S.; Graells, T.; Andersson, M.; Malmström, J.; Wu, Z. G.; Hjort, K.

2017-08-01

Inertial focusing is a promising microfluidic technology for concentration and separation of particles by size. However, there is a strong correlation of increased pressure with decreased particle size. Theory and experimental results for larger particles were used to scale down the phenomenon and find the conditions that focus 1 µm particles. High pressure experiments in robust glass chips were used to demonstrate the alignment. We show how the technique works for 1 µm spherical polystyrene particles and for Escherichia coli, not being harmful for the bacteria at 50 µl min-1. The potential to focus bacteria, simplicity of use and high throughput make this technology interesting for healthcare applications, where concentration and purification of a sample may be required as an initial step.

A comparison of the influence of different dopants on the radar-absorbing properties of barium hexaferrite

International Nuclear Information System (INIS)

Jones, M.; Suder, M.M.; Edge, A.J.J.; Stewart, G.A.; Hutchison, W.D.; Amiet, A.; Jewsbury, P.

2004-01-01

Full text: The ferromagnetic resonance of barium hexaferrite is at approximately 48 GHz, which sits well above the frequency bands employed by most radar systems. However, certain elements (or combinations of elements), when doped into the iron sub-lattice, have been observed to weaken the system's uniaxial magnetocrystalline anisotropy and thereby lower the ferromagnetic resonance frequency. This contribution presents a survey of ferromagnetic resonance frequencies published in the literature, as well as resonance frequencies that we have converted from published magnetic characterisations of the magnetic anisotropy. In several cases we have confirmed the reliability of such converted values, and new data will be presented for (Co 1/2 Zr 1/2 )- and (Co 1/2 Mo 1/2 )-doped barium hexaferrite. Our specimen materials were prepared by solid state reaction, and characterised using x-ray powder diffraction and 57 Fe Moessbauer spectroscopy. The electromagnetic response characteristics were recorded with a microwave network analyser, using either a co-axial specimen (0 - 18 GHz) or a larger, planar tile specimen (0 - 40 GHz). An ideal radar absorbing material would require just a small concentration of an inexpensive dopant to lower the ferromagnetic resonance frequency into the 0 - 2 GHz band that is typical of long-range radars. The likelihood of finding such a doped barium hexaferrite system will be discussed

Theoretical study of defects Cu{sub 3}SbSe{sub 4}: Search for optimum dopants for enhancing thermoelectric properties

Energy Technology Data Exchange (ETDEWEB)

Do, Dat T., E-mail: dodat@msu.edu; Mahanti, S.D., E-mail: mahanti@pa.msu.edu

2015-03-15

Highlights: • We present the first systematic study of defects in Cu{sub 3}SbSe{sub 4}. • Possible n-type and p-type dopants are suggested for Cu and Sb site. • Transition-metal substitutions on Sb potentially improve thermoelectric properties. • Transition-metal substitutions on Se strongly distort local crystal geometry. • p-type behavior of as synthesized Cu{sub 3}SbSe{sub 4} is most likely due to Cu. - Abstract: Cu{sub 3}SbSe{sub 4} is a promising thermoelectric material due to high thermopower (>400μV/K) at 300 K and higher. Although it has a simple crystal structure derived from zinc blende structure, previous work has shown that the physics of band gap formation is quite subtle due to the importance of active lone pair (5s{sup 2}) of Sb and the non-local exchange interaction between these and Se 5p electrons. Since for any application of semiconductors understanding the properties of defects is essential, we discuss the results of a systematic study of several point defects in Cu{sub 3}SbSe{sub 4} including vacancies and substitutions for each of the components. First principles calculations using density functional theory show that among variety of possible dopants, p-type doping can be done by substituting Sb with group IV elements including Sn, Ge, Pb and Ti and n-type doping can be done by replacing Cu by Mg, Zn. Doping at the Se site appears to be rather difficult. Electronic structure calculations also suggest that the p-type behavior seen in nominally pure Cu{sub 3}SbSe{sub 4} is most likely due to Cu vacancy rather than Se vacancy.

Interfacial Passivation of the p-Doped Hole-Transporting Layer Using General Insulating Polymers for High-Performance Inverted Perovskite Solar Cells.

Science.gov (United States)

Zhang, Fan; Song, Jun; Hu, Rui; Xiang, Yuren; He, Junjie; Hao, Yuying; Lian, Jiarong; Zhang, Bin; Zeng, Pengju; Qu, Junle

2018-05-01

Organic-inorganic lead halide perovskite solar cells (PVSCs), as a competing technology with traditional inorganic solar cells, have now realized a high power conversion efficiency (PCE) of 22.1%. In PVSCs, interfacial carrier recombination is one of the dominant energy-loss mechanisms, which also results in the simultaneous loss of potential efficiency. In this work, for planar inverted PVSCs, the carrier recombination is dominated by the dopant concentration in the p-doped hole transport layers (HTLs), since the F4-TCNQ dopant induces more charge traps and electronic transmission channels, thus leading to a decrease in open-circuit voltages (V OC ). This issue is efficiently overcome by inserting a thin insulating polymer layer (poly(methyl methacrylate) or polystyrene) as a passivation layer with an appropriate thickness, which allows for increases in the V OC without significantly sacrificing the fill factor. It is believed that the passivation layer attributes to the passivation of interfacial recombination and the suppression of current leakage at the perovskite/HTL interface. By manipulating this interfacial passivation technique, a high PCE of 20.3% is achieved without hysteresis. Consequently, this versatile interfacial passivation methodology is highly useful for further improving the performance of planar inverted PVSCs. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

[Condition optimization for bio-oxidation of high-S and high-As gold concentrate].

Science.gov (United States)

Yang, Caiyun; Dong, Bowen; Wang, Meijun; Ye, Zhiyong; Zheng, Tianling; Huang, Huaiguo

2015-12-04

To study the effects of temperature and lixivium return on the concentrate bio-oxidation and rate of gold cyanide leaching. The bioleaching of a high-sulphur (S) and high-arsenic (As) refractory gold concentrate was conducted, and we studied the effects of different temperature (40 ° and 45 °C) and lixivium return (0 and 600 mL) on the bio-oxidation efficiency. The bacterial community structure also was investigated by 16S rRNA gene clone library. The results showed that both the temperature and lixivium return significantly influenced the oxidation system. The temperature rising elevated the oxidation level, while the addition of lixivium depressed the oxidation. Dissimilarity and DCA (detrended correspondence analysis) indicated the effect of temperature on oxidation system was much greater than lixivium. The bacterial community was comprised by Acidithiocacillus caldu (71%) Leptospirillum ferriphilum (23%) and Sulfobacillus thermosulfidooxidans (6%) indicated by the clone library, and the OTU coverage based on 97% sequence similarity was as high as 93.67%. Temperature rising to 45 T would improve the oxidation efficiency while lixivium return would decrease it. This study is helpful to provide an important guiding value for the industry cost optimization of mesophile bacterial oxidation and reduction process.

Polyaspartic Acid Concentration Controls the Rate of Calcium Phosphate Nanorod Formation in High Concentration Systems

Energy Technology Data Exchange (ETDEWEB)

Krogstad, Daniel V. [Biosystems and; Wang, Dongbo [Biosystems and; Lin-Gibson, Sheng [Biosystems and

2017-08-31

Polyelectrolytes are known to greatly affect calcium phosphate (CaP) mineralization. The reaction kinetics as well as the CaP phase, morphology and aggregation state depend on the relative concentrations of the polyelectrolyte and the inorganic ions in a complex, nonlinear manner. This study examines the structural evolution and kinetics of polyaspartic acid (pAsp) directed CaP mineralization at high concentrations of polyelectrolytes, calcium, and total phosphate (19–30 mg/mL pAsp, 50–100 mM Ca2+, Ca/P = 2). Using a novel combination of characterization techniques including cryogenic transmission electron microscopy (cryo-TEM), spectrophotometry, X-ray total scattering pair distribution function analysis, and attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), it was determined that the CaP mineralization occurred over four transition steps. The steps include the formation of aggregates of pAsp stabilized CaP spherical nanoparticles (sNP), crystallization of sNP, oriented attachment of the sNP into nanorods, and further crystallization of the nanorods. The intermediate aggregate sizes and the reaction kinetics were found to be highly polymer concentration dependent while the sizes of the particles were not concentration dependent. This study demonstrates the complex role of pAsp in controlling the mechanism as well as the kinetics of CaP mineralization.

Neutron transmutation doping of polycrystalline silicon

International Nuclear Information System (INIS)

Cleland, J.W.; Westbrook, R.D.; Wood, R.F.; Young, R.T.

1976-04-01

Chemical vapor deposition (CVD) of doped silane has been used by others to deposit a polycrytalline silicon film (polysil) on metal or graphite substrates, but dopant migration to grain boundaries during deposition apparently prohibits attaining a uniform or desired dopant concentration. In contrast, we have used neutron transmutation doping to introduce a uniform phosphorus dopant concentration in commercially available undoped CVD polysil at doping concentrations greater than or equal to 2 x 10 15 cm -3 . Radiation damage annealing to 800 0 C did not indicate dopant migration. Carrier mobility increased with doping concentration and the minority carrier lifetime (MCL) appears to be comparable to that of neutron transmutation doped (NTD) single crystal Si. Application of this technique to photovoltaic solar cell fabrication is discussed

Selection of common bean lines with high grain yield and high grain calcium and iron concentrations

Directory of Open Access Journals (Sweden)

Nerinéia Dalfollo Ribeiro

2014-02-01

Full Text Available Genetic improvement of common bean nutritional quality has advantages in marketing and can contribute to society as a food source. The objective of this study was to evaluate the genetic variability for grain yield, calcium and iron concentrations in grains of inbred common bean lines obtained by different breeding methods. For this, 136 F7 inbred lines were obtained using the Pedigree method and 136 F7 inbred lines were obtained using the Single-Seed Descent (SSD method. The lines showed genetic variability for grain yield, and concentrations of calcium and iron independently of the method of advancing segregating populations. The Pedigree method allows obtaining a greater number of lines with high grain yield. Selection using the SSD method allows the identification of a larger number of lines with high concentrations of calcium and iron in grains. Weak negative correlations were found between grain yield and calcium concentration (r = -0.0994 and grain yield and iron concentration (r = -0.3926. Several lines show genetic superiority for grain yield and concentrations of calcium and iron in grains and their selection can result in new common bean cultivars with high nutritional quality.

Improved Performance and Reproducibility of Perovskite Solar Cells by Well-Soluble Tris(pentafluorophenyl)borane as a p-Type Dopant.

Science.gov (United States)

Ye, Tengling; Wang, Junhai; Chen, Wenbo; Yang, Yulin; He, Dongqing

2017-05-31

In this work, well-soluble tris(pentafluorophenyl)borane (BCF) is introduced for the first time into 2,2',7,7'-tetrakis(N,N'-di-p-methoxyphenylamine)-9,9'-spirobifluorene (spiro-OMeTAD) as a p-dopant. The conductivity of spiro-OMeTAD films is dramatically enhanced. When the BCF-doped spiro-OMeTAD film is used as a hole-transport layer (HTL) in perovskite solar cells (PSCs), nearly double increase in power conversion efficiency (PCE) is obtained compared to that of the PSCs based on a pristine spiro-OMeTAD HTL. By the introduction of lithium bis(trifluoromethanesulfonyl)imide and 4-tert-butylpyridine into the BCF-doped spiro-OMeTAD film, the conductivity of spiro-OMeTAD film can be further enhanced, and an optimum PCE of 14.65% is obtained. In addition, the average efficiency of the device and the reproducibility of BCF-based PSCs are better than those of FK209-based PSCs. The working mechanism of the BCF doping effect on spiro-OMeTAD is studied in detail. The strong electron-accepting ability, excellent solubility in common organic solvents, and the low cost make BCF a very attractive p-type dopant for spiro-OMeTAD.

Study of carrier concentration in single InP nanowires by luminescence and Hall measurements

International Nuclear Information System (INIS)

Lindgren, David; Hultin, Olof; Heurlin, Magnus; Storm, Kristian; Borgström, Magnus T; Samuelson, Lars; Gustafsson, Anders

2015-01-01

The free electron carrier concentrations in single InP core–shell nanowires are determined by micro-photoluminescence, cathodoluminescence (CL) and Hall effect measurements. The results from luminescence measurements were obtained by solving the Fermi–Dirac integral, as well as by analyzing the peak full width at half maximum (FWHM). Furthermore, the platform used for Hall effect measurements, combined with spot mode CL spectroscopy, is used to determine the carrier concentrations at specific positions along single nanowires. The results obtained via luminescence measurements provide an accurate and rapid feedback technique for the epitaxial development of doping incorporation in nanowires. The technique has been employed on several series of samples in which growth parameters, such as V/III-ratio, temperature and dopant flows, were investigated in an optimization procedure. The correlation between the Hall effect and luminescence measurements for extracting the carrier concentration of different samples were in excellent agreement. (paper)

Dopant spin states and magnetism of Sn{sub 1−x}Fe{sub x}O{sub 2} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Punnoose, A., E-mail: apunnoos@boisestate.edu; Dodge, Kelsey; Reddy, K. M.; Franco, Nevil; Chess, Jordan; Eixenberger, Josh [Department of Physics, Boise State University, Boise, Idaho 83725-1570 (United States); Beltrán, J. J. [Department of Physics, Boise State University, Boise, Idaho 83725-1570 (United States); Grupo de Estado Sólido, Facultad de Ciencias Exactas y Naturales, Universidad de Antioquia UdeA, Calle 70 No 52-21, Medellín (Colombia); Barrero, C. A. [Grupo de Estado Sólido, Facultad de Ciencias Exactas y Naturales, Universidad de Antioquia UdeA, Calle 70 No 52-21, Medellín (Colombia)

2014-05-07

This work reports detailed investigations of a series of ∼2.6 nm sized, Sn{sub 1−x}Fe{sub x}O{sub 2} crystallites with x = 0–0.10 using Mossbauer spectroscopy, x-ray photoelectron spectroscopy (XPS), electron paramagnetic resonance spectroscopy (EPR), and magnetometry to determine the oxidation state of Fe dopants and their role in the observed magnetic properties. The magnetic moment per Fe ion μ was the largest ∼6.48 × 10{sup −3} μ{sub B} for the sample with the lowest (0.001%) Fe doping, and it showed a rapid downward trend with increasing Fe doping. Majority of the Fe ions are in 3+ oxidation state occupying octahedral sites. Another significant fraction of Fe dopant ions is in 4+ oxidation state and a still smaller fraction might be existing as Fe{sup 2+} ions, both occupying distorted sites, presumably in the surface regions of the nanocrystals, near oxygen vacancies. These studies also suggest that the observed magnetism is not due to exchange coupling between Fe{sup 3+} spins. A more probable role for the multi-valent Fe ions may be to act as charge reservoirs, leading to charge transfer ferromagnetism.

High-concentration planar microtracking photovoltaic system exceeding 30% efficiency

Science.gov (United States)

Price, Jared S.; Grede, Alex J.; Wang, Baomin; Lipski, Michael V.; Fisher, Brent; Lee, Kyu-Tae; He, Junwen; Brulo, Gregory S.; Ma, Xiaokun; Burroughs, Scott; Rahn, Christopher D.; Nuzzo, Ralph G.; Rogers, John A.; Giebink, Noel C.

2017-08-01

Prospects for concentrating photovoltaic (CPV) power are growing as the market increasingly values high power conversion efficiency to leverage now-dominant balance of system and soft costs. This trend is particularly acute for rooftop photovoltaic power, where delivering the high efficiency of traditional CPV in the form factor of a standard rooftop photovoltaic panel could be transformative. Here, we demonstrate a fully automated planar microtracking CPV system 660× concentration ratio over a 140∘ full field of view. In outdoor testing over the course of two sunny days, the system operates automatically from sunrise to sunset, outperforming a 17%-efficient commercial silicon solar cell by generating >50% more energy per unit area per day in a direct head-to-head competition. These results support the technical feasibility of planar microtracking CPV to deliver a step change in the efficiency of rooftop solar panels at a commercially relevant concentration ratio.

Doping of two-dimensional MoS2 by high energy ion implantation

Science.gov (United States)

Xu, Kang; Zhao, Yuda; Lin, Ziyuan; Long, Yan; Wang, Yi; Chan, Mansun; Chai, Yang

2017-12-01

Two-dimensional (2D) materials have been demonstrated to be promising candidates for next generation electronic circuits. Analogues to conventional Si-based semiconductors, p- and n-doping of 2D materials are essential for building complementary circuits. Controllable and effective doping strategies require large tunability of the doping level and negligible structural damage to ultrathin 2D materials. In this work, we demonstrate a doping method utilizing a conventional high-energy ion-implantation machine. Before the implantation, a Polymethylmethacrylate (PMMA) protective layer is used to decelerate the dopant ions and minimize the structural damage to MoS2, thus aggregating the dopants inside MoS2 flakes. By optimizing the implantation energy and fluence, phosphorus dopants are incorporated into MoS2 flakes. Our Raman and high-resolution transmission electron microscopy (HRTEM) results show that only negligibly structural damage is introduced to the MoS2 lattice during the implantation. P-doping effect by the incorporation of p+ is demonstrated by Photoluminescence (PL) and electrical characterizations. Thin PMMA protection layer leads to large kinetic damage but also a more significant doping effect. Also, MoS2 with large thickness shows less kinetic damage. This doping method makes use of existing infrastructures in the semiconductor industry and can be extended to other 2D materials and dopant species as well.

Decrease of oxygen vacancy by Zn-doped for improving solar-blind photoelectric performance in β-Ga2O3 thin films

Science.gov (United States)

Guo, Daoyou; Qin, Xinyuan; Lv, Ming; Shi, Haoze; Su, Yuanli; Yao, Guosheng; Wang, Shunli; Li, Chaorong; Li, Peigang; Tang, Weihua

2017-11-01

Highly (201) oriented Zn-doped β-Ga2O3 thin films with different dopant concentrations were grown on (0001) sapphire substrates by radio frequency magnetron sputtering. With the increase of Zn dopant concentration, the crystal lattice expands, the energy band gap shrinks, and the oxygen vacancy concentration decreases. Both the metal semiconductor metal (MSM) structure photodetectors based on the pure and Zn-doped β-Ga2O3 thin films exhibit solar blind UV photoelectric property. Compared to the pure β-Ga2O3 photodetector, the Zn-doped one exhibits a lower dark current, a higher photo/dark current ratio, a faster photoresponse speed, which can be attributed to the decreases of oxygen vacancy concentration.[Figure not available: see fulltext.

Investigation of the areas of high radon concentration in Gyeongju

International Nuclear Information System (INIS)

Lee, Jung Min; Park, Chan Hee; Kim, Shin Jae; Moon, Joo Hyun

2013-01-01

The aim of this study was to survey the radon concentrations at 21 elementary schools in Gyeongju, Republic of Korea, to identify those schools with high radon concentrations. Considering their geological characteristics and the preliminary survey results, three schools were finally placed under close scrutiny. For these three schools, continuous measurements over 48 h were taken at the principal's and administration office. The radon concentrations at one school, Naenam, exceeded the action level (148 Bq/m 3 ) established by the U.S. EPA, while those at the other two schools were below that level. - Highlights: • Preliminary measurements of the indoor radon concentrations were performed at the auditoriums in 23 elementary schools in Gyeongju. • Considering the geological characteristics and preliminary survey results, three elementary schools were screened for closer scrutiny. • For the three schools, continuous measurements were made at their principal's and administration offices over 48-h period. • The scrutiny revealed one elementary school of high radon concentration much higher than the U.S. EPA action level

Doping of (Bi,Pb)-2223 with metal oxides

International Nuclear Information System (INIS)

Goehring, D.; Vogt, M.; Wischert, W.; Kemmler-Sack, S.

1997-01-01

The effect of doping on formation, superconductivity and pinning forces of (Bi,Pb)-2223 was studied for several dopants. They can be subdivided into promoters (Cu, Mn at low doping level of x=0.1 and Rh) and inhibitors (Mg, Al, Sn, Co, Y, Pd and high substitution levels of Mn and Ni) of the transformation of the precursor material into (Bi,Pb)-2223. According to X-ray diffraction (XRD) studies the incorporation of the dopant into the 2223 lattice is restricted to a very low doping level. Higher dopant concentrations are accompanied by a segregation of secondary phases. These segregations are not effective in the process of creating flux pinning centres. A depression of T c is observed for 2223 materials with the dopants Co, Ni and Pd. (orig.)

Effects of Ca-dopant on the pyroelectric, piezoelectric and dielectric properties of (Sr 0.6Ba 0.4) 4Na 2Nb 10O 30 ceramics

KAUST Repository

Yao, Yingbang

2012-12-01

Calcium-doped sodium strontium barium niobate (SBNN, (Sr 0.6Ba 0.4) 4-xCa xNa 2Nb 10O 30, 0 ≤ x ≤ 0.5) ceramics were prepared by a conventional solid-state reaction method. SBNN showed \\'filled\\' tetragonal tungsten-bronze structure with fully occupied A-sites. The tetragonal structure, as revealed by X-ray diffraction (XRD) and Raman spectroscopy, was not affected by the Ca-dopant. Effects of Ca-doping concentration on the phase transitions as well as ferroelectric, piezoelectric and pyroelectric properties of the SBNN ceramics were investigated. From the dielectric studies, two anomalies were observed, namely, a sharp normal ferroelectric transition at 260 °C and a broad maximum at round -110 °C. The later was affected by the Ca-doping concentration and its origin was discussed. At x = 0.3, the sample exhibited the highest pyroelectric coefficient of 168 μC/m 2 K and the largest piezoelectric coefficient (d 33) of 63 pC/N at room temperature. On the basis of our results, the pyroelectric properties of the SBNN were improved by Ca-doping. © 2012 Elsevier B.V. All rights reserved.

Effects of Ca-dopant on the pyroelectric, piezoelectric and dielectric properties of (Sr 0.6Ba 0.4) 4Na 2Nb 10O 30 ceramics

KAUST Repository

Yao, Yingbang; Mak, C. L.

2012-01-01

Calcium-doped sodium strontium barium niobate (SBNN, (Sr 0.6Ba 0.4) 4-xCa xNa 2Nb 10O 30, 0 ≤ x ≤ 0.5) ceramics were prepared by a conventional solid-state reaction method. SBNN showed 'filled' tetragonal tungsten-bronze structure with fully occupied A-sites. The tetragonal structure, as revealed by X-ray diffraction (XRD) and Raman spectroscopy, was not affected by the Ca-dopant. Effects of Ca-doping concentration on the phase transitions as well as ferroelectric, piezoelectric and pyroelectric properties of the SBNN ceramics were investigated. From the dielectric studies, two anomalies were observed, namely, a sharp normal ferroelectric transition at 260 °C and a broad maximum at round -110 °C. The later was affected by the Ca-doping concentration and its origin was discussed. At x = 0.3, the sample exhibited the highest pyroelectric coefficient of 168 μC/m 2 K and the largest piezoelectric coefficient (d 33) of 63 pC/N at room temperature. On the basis of our results, the pyroelectric properties of the SBNN were improved by Ca-doping. © 2012 Elsevier B.V. All rights reserved.

Hydrogen Storage Properties of Lithium Aluminohydride modified by dopants and mechanochemistry

Energy Technology Data Exchange (ETDEWEB)

Hosokawa, Keita [Iowa State Univ., Ames, IA (United States)

2002-01-01

Alkali metal aluminohydrides have high potential as solid hydrogen storage materials. They have been known for their irreversible dehydrogenation process below 100 atm until Bogdanovic et al [1, 2] succeeded in the re-hydrogenation of NaAlH₄ below 70 atm. They achieved 4 wt.% H₂ reversible capacity by doping NaAlH₄ with Ti and/or Fe organo-metalic compounds as catalysts. This suggests that other alkali and, possibly alkaline earth metal aluminohydrides can be used for reversible hydrogen storage when modified by proper dopants. In this research, Zr₂₇Ti₉Ni₃₈V₅Mn₁₆Cr₅, LaNi_4.85Sn_0.15, Al₃Ti, and PdCl₂ were combined with LiAlH₄ by ball-milling to study whether or not LiAlH₄ is capable to both absorb and desorb hydrogen near ambient conditions. X-ray powder diffraction, differential thermal analysis, and scanning electron microscopy were employed for sample characterizations. All four compounds worked as catalysts in the dehydrogenation reactions of both LiAlH₄ and Li₃AlH₆ by inducing the decomposition at lower temperature. However, none of them was applicable as catalyst in the reverse hydrogenation reaction at low to moderate hydrogen pressure.

Structural and dielectric studies of Zr and Co co-substituted Ni0.5Zn0.5Fe2O4 using sol-gel auto combustion method

Science.gov (United States)

Jalaiah, K.; Vijaya Babu, K.; Rajashekhar Babu, K.; Chandra Mouli, K.

2018-06-01

Zr and Co substituted Ni0.5Zn0.5 ZrxCuxFe2-2xO4 with x values varies from the 0.0 to 0.4 in steps of 0.08 wt% ferrites synthesized by using sol-gel auto combustion method. The XRD patterns give evidence for formation of the single phase cubic spinel. The lattice constant was initially decreased from 8.3995 Å to 8.3941 Å with dopant concentration for x = 0.00-0.08 thereafter the lattice parameter steeply increased up to 8.4129 Å fox x = 0.4 with increasing dopant concentration. The estimated crystallite size and measured particle sizes are in comparable nano size. The grain size initially increased 2.3137-3.0430 μm, later it decreased to 2.2952 μm with increasing dopant concentration. The prepared samples porosity shows the opposite trend to grain size. The FT-IR spectrum for prepared samples shows the Fd3m (O7h). The wavenumber for tetrahedral site increased from 579 cm-1 to 593 cm-1 with increasing dopant concentration and the wavenumber of octahedral site are initially decreased from 414 cm-1 to 400 cm-1 for x = 0.00 to x = 0.08 later increased to 422 cm-1 with increasing dopant concentration. The dielectric constant increased from 8.85 to 34.5127 with dopant increasing concentration. The corresponding loss factor was fallows the similar trend as dielectric constant. The AC conductivity increased with increasing dopant concentration from 3.0261 × 10-7 S/m to 4.4169 × 10-6 S/m.

Theoretical characterization of a class of orange dopants for white-light-emitting single polymers

International Nuclear Information System (INIS)

Hu, Bo; Yao, Chan; Wang, Qingwei; Zhang, Hao; Yu, Jiankang

2012-01-01

New single-polymer white electroluminescent systems containing two individual emission species − polyfluorene as a blue host and 2,1,3-benzothiadiazole(BTD) derivative as an orange dopant − have been designed and investigated on the basis of the quantum chemical calculations. Calculations show that the change of chemical composition along the backbone in BTD-based derivative yields modifications to the electronic and optical properties. Furthermore, by introducing electron-donating groups [−CH 3 , –OCH 3 , and –NH 2 ] on terminal N,N-disubstituted amino groups, desirable orange emission can be obtained and may be further combined with polyfluorene to form white light. Also, we estimate the reorganization energies upon cation or anion formation as one of the important parameters of mobility with the charge hopping model to determine whether the molecular structural changes may improve the hole/electron transport. The electrostatic surface potentials are finally taken into account to evaluate stability. -- Graphical abstract: New single-polymer white electroluminescent systems containing two individual emission species − polyfluorene as a blue host and 2,1,3-benzothiadiazole(BTD) derivative as an orange dopant − have been designed and investigated on the basis of the quantum chemical calculations. Highlights: ► The change of chemical composition along the backbone yields modifications to the electronic and optical properties. ► Introducing [–CH 3 , –OCH 3 , and –NH 2 ] on terminal N,N-disubstituted amino groups, desirable orange emission can be obtained. ► Desirable orange emission may be further combined with polyfluorene to form white light. ► Designed BTD-based derivatives can function as good hole or ambipolar transport materials in the OLEDs. ► According to the calculated electrostatic surface potentials, OMC-PZ has better stability than that of OMC-PZT.

Flat-plate solar array project process development area process research of non-CZ silicon material

Science.gov (United States)

1985-01-01

Three sets of samples were laser processed and then cell processed. The laser processing was carried out on P-type and N-type web at laser power levels from 0.5 joule/sq cm to 2.5 joule/sq cm. Six different liquid dopants were tested (3 phosphorus dopants, 2 boron dopants, 1 aluminum dopant). The laser processed web strips were fabricated into solar cells immediately after laser processing and after various annealing cycles. Spreading resistance measurements made on a number of these samples indicate that the N(+)P (phosphorus doped) junction is approx. 0.2 micrometers deep and suitable for solar cells. However, the P(+)N (or P(+)P) junction is very shallow ( 0.1 micrometers) with a low surface concentration and resulting high resistance. Due to this effect, the fabricated cells are of low efficiency. The maximum efficiency attained was 9.6% on P-type web after a 700 C anneal. The main reason for the low efficiency was a high series resistance in the cell due to a high resistance back contact.

Yellow emitting Iridium (III) phenyl-benzothiazole complexes with different β-diketone ancillary ligands as dopants in white organic light-emitting diodes

Science.gov (United States)

Ivanov, P.; Petrova, P.; Tomova, R.

2018-03-01

We discuss the influence of the type of β-diketone ancillary ligand in Iridium (III) bis phenyl-benzothiazole complexes ((bt)2Ir(β-diketone)) on their photophysical and electroluminescent properties when they are used as dopants in white organic light-emitting diodes (WOLED). For this purpose, we investigated four novel yellow cyclometalated complexes: (bt)2Ir(dbm), (bt)2Ir(fmtdbm), (bt)2Ir(tta) and (bt)2Ir(bsm), where dbm = 1,3-diphenylpropane-1,3-dionate; fmtdbm = 1-(4-fluorophenyl)-3-(4-methoxyphenyl)propane-1,3-dionate; tta = 4,4,4-trifluoro-1-(thiophene-2-yl)butane-1,3-dionate; and bsm = 1-phenylicosane-1,3-dionate). To obtain white light by mixing emissions of two complementary colors (yellow emitted by the dopant and blue, by another emitter), we chose the following OLED structure: ITO/doped HTL/ElL/ETL/M, where ITO was a transparent anode of In2O3:SnO2; M, a metallic Al cathode; HTL, 4,4’-Bis(9H-carbazol-9-yl)biphenyl (CBP) involved in a poly(N-vinylcarbazole) (PVK) matrix; ElL, an electroluminescent layer of aluminum(III)bis(2-methyl-8-quninolinato)-4-phenylphenolate (BAlq); and ETL, an electron-transporting layer of zinc(II)bis(2-2-hydroxyphenyl)benzothiazole. We found that all complexes are suitable candidates for fabrication of WOLED. The best results were demonstrated by the device doped with 2 wt % of (bt)2Ir(bsm), which had twice as high luminescence (1100 cd/m2) and one-and-a-half as high current efficiency (5 cd/A) as the device doped with 1.25 wt % of the known (bt)2Ir(acac), with its 580 cd/m2 and 3.4 cd/A at approximately the same CIE (Commission Internationale de L’Eclairage) (x/y) coordinates of the warm white light emitted by the two devices.

Improved electron injection and transport by use of baking soda as a low-cost, air-stable, n-dopant for solution-processed phosphorescent organic light-emitting diodes

Science.gov (United States)

Earmme, Taeshik; Jenekhe, Samson A.

2013-06-01

Sodium bicarbonate (baking soda, NaHCO3) is found to be an efficient low-cost, air-stable, and environmentally friendly n-dopant for electron-transport layer (ETL) in solution-processed phosphorescent organic light-emitting diodes (PhOLEDs). A 2.0-fold enhancement in power efficiency of blue PhOLEDs is observed by use of NaHCO3-doped 4,7-diphenyl-1,10-phenanthroline (BPhen) ETL. The bulk conductivity of NaHCO3-doped BPhen film is increased by 5 orders of magnitude. Enhanced performance of PhOLEDs is similarly observed by use of NaHCO3-doped 1,3,5-tris(m-pyrid-3-yl-phenyl)benzene ETL. These results demonstrate that sodium bicarbonate is an effective n-dopant in organic electronics.

Highly concentrated zinc oxide nanocrystals sol with strong blue emission

International Nuclear Information System (INIS)

Vafaee, M.; Sasani Ghamsari, M.; Radiman, S.

2011-01-01

Highly concentrated ZnO sol was synthesized by an improved sol-gel method. Water was used as a modifier to control the sol-gel reaction and provide a way to increase the sol concentration. Concentration of ZnO in the prepared sol is higher than from other methods. Optical absorption and photoluminescence were used to investigate optical properties of the prepared sol. FTIR test was performed to study the influence of water on the compounds of as-prepared sol. The size and morphology of ZnO nanoparticles have been studied by HRTEM. The prepared colloidal ZnO nanocrystals have narrow size distribution (5-8 nm) and showed strong blue emission. The prepared sol has enough potential for optoelectronic applications. - Research highlights: → Novel sol-gel route has been employed to prepare highly concentrated ZnO colloidal nanocrystals. → Water has been used to control the sources of emission in synthesized material. → A strong blue luminescent material has been obtained.

Efficient purification and concentration of viruses from a large body of high turbidity seawater.

Science.gov (United States)

Sun, Guowei; Xiao, Jinzhou; Wang, Hongming; Gong, Chaowen; Pan, Yingjie; Yan, Shuling; Wang, Yongjie

2014-01-01

Marine viruses are the most abundant entities in the ocean and play crucial roles in the marine ecological system. However, understanding of viral diversity on large scale depends on efficient and reliable viral purification and concentration techniques. Here, we report on developing an efficient method to purify and concentrate viruses from large body of high turbidity seawater. The developed method characterizes with high viral recovery efficiency, high concentration factor, high viral particle densities and high-throughput, and is reliable for viral concentration from high turbidity seawater. Recovered viral particles were used directly for subsequent analysis by epifluorescence microscopy, transmission electron microscopy and metagenomic sequencing. Three points are essential for this method:•The sampled seawater (>150 L) was initially divided into two parts, water fraction and settled matter fraction, after natural sedimentation.•Both viruses in the water fraction concentrated by tangential flow filtration (TFF) and viruses isolated from the settled matter fraction were considered as the whole viral community in high turbidity seawater.•The viral concentrates were re-concentrated by using centrifugal filter device in order to obtain high density of viral particles.

Comprehensive growth and characterization study on highly n-doped InGaAs as a contact layer for quantum cascade laser applications

Science.gov (United States)

Demir, Ilkay; Altuntas, Ismail; Bulut, Baris; Ezzedini, Maher; Ergun, Yuksel; Elagoz, Sezai

2018-05-01

We present growth and characterization studies of highly n-doped InGaAs epilayers on InP substrate by metal organic vapor phase epitaxy to use as an n-contact layer in quantum cascade laser applications. We have introduced quasi two-dimensional electrons between 10 s pulsed growth n-doped InGaAs epilayers to improve both carrier concentration and mobility of structure by applying pulsed growth and doping methods towards increasing the Si dopant concentration in InGaAs. Additionally, the V/III ratio optimization under fixed group III source flow has been investigated with this new method to understand the effects on both crystalline quality and electrical properties of n-InGaAs epilayers. Finally, we have obtained high crystalline quality of n-InGaAs epilayers grown by 10 s pulsed as a contact layer with 2.8 × 1019 cm‑3 carrier concentration and 1530 cm2 V‑1 s‑1 mobility.

Effect of aluminium concentration and boron dopant on environmental embrittlement in FeAl aluminides

International Nuclear Information System (INIS)

Liu, C.T.; George, E.P.

1991-01-01

This paper reports on the room-temperature tensile properties of FeAl aluminides determined as functions of aluminum concentration (35 to 43 at. % Al), test environment, and surface (oil) coating. The two lower aluminum alloys containing 35 and 36.5% Al are prone to severe environmental embrittlement, while the two higher aluminum alloys with 40 and 43% Al are much less sensitive to change in test environment and surface coating. The reason for the different behavior is that the grain boundaries are intrinsically weak in the higher aluminum alloys, and these weak boundaries dominate the low ductility and brittle fracture behavior of the 40 and 43% Al alloys. When boron is added to the 40% Al alloy as a grain-boundary strengthener, the environmental effect becomes prominent. In this case, the tensile ductility of the boron-doped alloy, just like that of the lower aluminum alloys, can be dramatically improved by control of test environment (e.g. dry oxygen vs air). Strong segregation of boron to the grain boundaries, with a segregation factor of 43, was revealed by Auger analyses

Growth of uniform lath-like α-(Fe,Al)OOH and disc-like α-(Fe,Al)2O3 nanoparticles in a highly alkaline medium

International Nuclear Information System (INIS)

Krehula, Stjepko; Music, Svetozar

2010-01-01

The effects of aluminium (Al 3+ )-dopant on the precipitation of uniform lath-like α-FeOOH particles, the obtention and growth of α-(Fe,Al)OOH and α-(Fe,Al) 2 O 3 solid solutions, particle size and shape were investigated using X-ray powder diffraction, Moessbauer and Fourier transform infrared spectroscopies, field emission scanning electron microscopy and energy dispersive X-ray spectroscopy. Acicular α-FeOOH particles, precipitated in a highly alkaline medium with the addition of tetramethylammonium hydroxide (TMAH), were used as reference material. The influence of Al-dopant was investigated by adding varying amounts of Al 3+ ions to the initial FeCl 3 solution. In the presence of lower concentrations of aluminium ions (up to 11.11 mol%) α-(Fe,Al)OOH as a single phase was formed, whereas higher concentrations led to an additional obtention and growth of α-(Fe,Al) 2 O 3 . Al-for-Fe substitution in the α-FeOOH and α-Fe 2 O 3 structures was confirmed by a decrease in the unit-cell dimensions, a decrease in the hyperfine magnetic field and an increase in the wave number of the infrared absorption bands. The presence of lower concentrations of aluminium ions (up to 11.11 mol%) in the precipitation system did not affect the size and shape of the α-(Fe,Al)OOH particles, whereas higher concentrations influenced a decrease in the length and aspect ratio. In the presence of 42.86 mol% Al 3+ ions fairly uniform disc-shaped α-(Fe,Al) 2 O 3 were formed.

Operation and scalability of dopant-segregated Schottky barrier MOSFETs with recessed channels

International Nuclear Information System (INIS)

Shih, Chun-Hsing; Hsia, Jui-Kai

2013-01-01

Recessed channels were used in scaled dopant-segregated Schottky barrier MOSFETs (DS-SBMOS) to control the severe short-channel effect. The physical operation and device scalability of the DS-SBMOS resulting from the presence of recessed channels and associated gate-corners are elucidated. The coupling of Schottky and gate-corner barriers has a key function in determining the on–off switching and drain current. The gate-corner barriers divide the channel into three regions for protection from the drain penetration field. To prevent resistive degradations in the drive current, an alternative asymmetric recessed channel (ARC) without a source-side gate-corner is proposed to simultaneously optimize both the short-channel effect and drive current in the scaled DS-SBMOS. By employing the proposed ARC architecture, the DS-SBMOS devices can be successfully scaled down, making them promising candidates for next-generation CMOS devices. (paper)

Investigation of MoO{sub x}/n-Si strong inversion layer interfaces via dopant-free heterocontact

Energy Technology Data Exchange (ETDEWEB)

Sun, Teng; Liu, Ruiyuan; Wu, Chen; Zhong, Yanan; Liu, Yuqiang; Wang, Yusheng; Han, Yujie; Xia, Zhouhui; Zou, Yatao; Song, Tao; Duhm, Steffen; Sun, Baoquan [Inst. of Functional Nano and Soft Materials (FUNSOM), Jiangsu Key Lab. for Carbon-Based Functional Materials and Devices, Collaborative Innovation Center of Suzhou Nano Science and Technology, Soochow Univ. (China); Wang, Rongbin [Inst. of Functional Nano and Soft Materials (FUNSOM), Jiangsu Key Lab. for Carbon-Based Functional Materials and Devices, Collaborative Innovation Center of Suzhou Nano Science and Technology, Soochow Univ. (China); Institut fuer Physik and IRIS Adlershof, Humboldt-Universitaet Berlin (Germany); Koch, Norbert [Institut fuer Physik and IRIS Adlershof, Humboldt-Universitaet Berlin (Germany); Helmholtz-Zentrum Berlin fuer Materialien und Energie GmbH, Berlin (Germany)

2017-07-15

Transition metal oxides (TMOs)/silicon (Si) heterocontact solar cells are currently under intensive investigation due to their simple fabrication process and less parasitic light absorption compared to traditional heterocontact counterparts. Effective segregation of carriers which is related to carrier-selective heterocontact is crucial for the performance of photovoltaic devices. Molybdenum oxide (MoO{sub x}, x ≤ 3), with a wide bandgap of ∝3.24 eV as well as defect bands derived from oxygen vacancies located inside the band gap, has been introduced to integrate with n-type Si (n-Si) as hole selective contact. Here, we utilize a stepwise in situ deposition of MoO{sub x} to investigate its interaction with Si by X-ray photoelectron spectroscopy (XPS) and ultraviolet photoelectron spectroscopy (UPS) measurements. A strong inversion layer originating from a charge transfer process is demonstrated in the n-Si surface region upon MoO{sub x} contact characterized by XPS, UPS, capacitance-voltage (C-V), and minority charge carrier lifetime mapping measurements. A dopant-free heterocontact is built within n-Si with a high built-in potential (V{sub bi}) of ∝0.80 V which benefits for acquiring a high open circuit voltage (V{sub oc}). These results give a detailed interpretation on the carrier transport mechanism of MoO{sub x}/n-Si heterocontact and also pave a new route toward fabricating high efficiency, low-cost solar cells. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

A compact spectrum splitting concentrator for high concentration photovoltaics based on the dispersion of a lens

Science.gov (United States)

He, J.; Flowers, C. A.; Yao, Y.; Atwater, H. A.; Rockett, A. A.; Nuzzo, R. G.

2018-06-01

Photovoltaic devices used in conjunction with functional optical elements for light concentration and spectrum splitting are known to be a viable approach for highly efficient photovoltaics. Conventional designs employ discrete optical elements, each with the task of either performing optical concentration or separating the solar spectrum. In the present work, we examine the performance of a compact photovoltaic architecture in which a single lens plays a dual role as both a concentrator and a spectrum splitter, the latter made possible by exploiting its intrinsic dispersion. A four-terminal two-junction InGaP/GaAs device is prepared to validate the concept and illustrates pathways for improvements. A spectral separation in the visible range is demonstrated at the focal point of a plano-convex lens with a geometric concentration ratio of 1104X with respect to the InGaP subcell.

Novel DDR Processing of Corn Stover Achieves High Monomeric Sugar Concentrations from Enzymatic Hydrolysis (230 g/L) and High Ethanol Concentration (10% v/v) During Fermentation

Energy Technology Data Exchange (ETDEWEB)

Chen, Xiaowen; Jennings, Ed; Shekiro, Joe; Kuhn, Erik M.; O' Brien, Marykate; Wang, Wei; Schell, Daniel J.; Himmel, Mike; Elander, Richard T.; Tucker, Melvin P.

2015-04-03

Distilling and purifying ethanol, butanol, and other products from second and later generation lignocellulosic biorefineries adds significant capital and operating cost for biofuels production. The energy costs associated with distillation affects plant gate and life cycle analysis costs. Lower titers in fermentation due to lower sugar concentrations from pretreatment increase both energy and production costs. In addition, higher titers decrease the volumes required for enzymatic hydrolysis and fermentation vessels. Therefore, increasing biofuels titers has been a research focus in renewable biofuels production for several decades. In this work, we achieved over 200 g/L of monomeric sugars after high solids enzymatic hydrolysis using the novel deacetylation and disc refining (DDR) process on corn stover. The high sugar concentrations and low chemical inhibitor concentrations from the DDR process allowed ethanol titers as high as 82 g/L in 22 hours, which translates into approximately 10 vol% ethanol. To our knowledge, this is the first time that 10 vol% ethanol in fermentation derived from corn stover without any sugar concentration or purification steps has been reported. Techno-economic analysis shows the higher titer ethanol achieved from the DDR process could significantly reduce the minimum ethanol selling price from cellulosic biomass.

Effect of additionally introduced Zn and Eu dopants on the photoluminescence spectra of Er-doped GaN crystals

International Nuclear Information System (INIS)

Mezdrogina, M.M.; Krivolapchuk, V.V.; Petrov, V.N.; Rodin, S.N.; Cherenkov, A.V.

2006-01-01

It is shown that the effect of dopants on the photoluminescence spectrum depends on the conductivity type of the initial GaN crystals. The sensitizing effect of emission is observed in wurtzite p-GaN crystals doped with Er. The same effect was previously observed in such crystals doped with Eu and Zn. In n-type GaN crystals sequentially doped with Eu, Zn, and Er, the emission is observed in visible and infrared ranges of the photoluminescence spectrum [ru

Gravitational settling of a highly concentrated system of solid spherical particles

Science.gov (United States)

Arkhipov, V. A.; Usanina, A. S.

2017-09-01

In the present paper, we report on the results of an experimental study of the process of gravity sedimentation of a cloud of monodispersed solid spherical particles with initial volume concentration C > 0.03, which was performed in a wide range of Reynolds numbers. An analytical estimate of the settling regimes of spherical particle clouds is presented. A new method for creating a spherical particle cloud with a high concentration of particles is proposed. A qualitative picture of the settling process of a highly concentrated particle cloud under gravity is revealed. A criterial dependence for the drag coefficient of a sedimenting spherical particle cloud as an entity is obtained.

Effect of annealing temperature and dopant concentration on the thermoluminescence sensitivity in LiF:Mg,Cu,Ag material.

Science.gov (United States)

Yahyaabadi, Akram; Torkzadeh, Falamarz; Rezaei Ochbelagh, Dariush; Hosseini Pooya, Seyed Mahdi

2018-04-24

LiF:Mg,Cu,Ag is a new dosimetry material that is similar to LiF:Mg,Cu,P in terms of dosimetric properties. The effect of the annealing temperature in the range of 200 to 350°C on the thermoluminescence (TL) sensitivity and the glow curve structure of this material at different concentrations of silver (Ag) was investigated. It has been demonstrated that the optimum values of the annealing temperature and the Ag concentration are 240°C and 0.1 mol% for better sensitivity, respectively. The TL intensity decreases at annealing temperatures lower than 240°C or higher than 240°C, reaching a minimum at 300°C and then again increases for various Ag concentrations. It was observed that the glow curve structure altered and the area under the low temperature peak as well as the area under the main dosimetric peak decreased with increasing annealing temperature. The position of the main dosimetric peak moved in the direction of higher temperatures, but at 320 and 350°C annealing temperatures, it shifted to lower temperatures. It was also observed that the TL sensitivity could partially be recovered by a combined annealing procedure. Copyright © 2018 John Wiley & Sons, Ltd.

Hydrogen Storage Properties of Lithium Aluminohydride Modified by Dopants and Mechanochemistry

Energy Technology Data Exchange (ETDEWEB)

Hosokawa, Keita [Iowa State Univ., Ames, IA (United States)

2002-01-01

Alkali metal aluminohydrides have high potential as solid hydrogen storage materials. They have been known for their irreversible dehydrogenation process below 100 atm until Bogdanovic et al [1, 2] succeeded in the re-hydrogenation of NaAlH₄ below 70 atm. They achieved 4 wt.% H₂ reversible capacity by doping NaAlH₄ with Ti and/or Fe organo-metalic compounds as catalysts. This suggests that other alkali and, possibly alkaline earth metal aluminohydrides can be used for reversible hydrogen storage when modified by proper dopants. In this research, Zr₂₇Ti₉Ni₃₈V₅Mn₁₆Cr₅, LaNi_4.85Sn_0.15, Al₃Ti, and PdCl₂ were combined , LaNi_4.85Sn_0.15, Al₃Ti, and PdCl₂ were combined with LiAlH₄ by ball-milling to study whether or not LiAlH₄ is capable to both absorb and desorb hydrogen near ambient conditions. X-ray powder diffraction, differential thermal analysis, and scanning electron microscopy were employed for sample characterizations. All four compounds worked as catalysts in the dehydrogenation reactions of both LiAlH₄ and Li₃AlH₆ by inducing the decomposition at lower temperature. However, none of them was applicable as catalyst in the reverse hydrogenation reaction at low to moderate hydrogen pressure.

Off-axis electron holography for the measurement of active dopants in silicon semiconductor devices

International Nuclear Information System (INIS)

Cooper, David

2016-01-01

There is a need in the semiconductor industry for a dopant profiling technique with nm-scale resolution. Here we demonstrate that off-axis electron holography can be used to provide maps of the electrostatic potential in semiconductor devices with nm-scale resolution. In this paper we will discuss issues regarding the spatial resolution and precision of the technique. Then we will discuss problems with specimen preparation and how this affects the accuracy of the measurements of the potentials. Finally we show results from experimental off-axis electron holography applied to nMOS and pMOS CMOS devices grown on bulk silicon and silicon- on-insulator type devices and present solutions to common problems that are encountered when examining these types of devices. (paper)

High Voltage Solar Concentrator Experiment with Implications for Future Space Missions

Science.gov (United States)

Mehdi, Ishaque S.; George, Patrick J.; O'Neill, Mark; Matson, Robert; Brockschmidt, Arthur

2004-01-01

This paper describes the design, development, fabrication, and test of a high performance, high voltage solar concentrator array. This assembly is believed to be the first ever terrestrial triple-junction-cell solar array rated at over 1 kW. The concentrator provides over 200 W/square meter power output at a nominal 600 Vdc while operating under terrestrial sunlight. Space-quality materials and fabrication techniques were used for the array, and the 3005 meter elevation installation below the Tropic of Cancer allowed testing as close as possible to space deployment without an actual launch. The array includes two concentrator modules, each with a 3 square meter aperture area. Each concentrator module uses a linear Fresnel lens to focus sunlight onto a photovoltaic receiver that uses 240 series-connected triple-junction solar cells. Operation of the two receivers in series can provide 1200 Vdc which would be adequate for the 'direct drive' of some ion engines or microwave transmitters in space. Lens aperture width is 84 cm and the cell active width is 3.2 cm, corresponding to a geometric concentration ratio of 26X. The evaluation includes the concentrator modules, the solar cells, and the materials and techniques used to attach the solar cells to the receiver heat sink. For terrestrial applications, a finned aluminum extrusion was used for the heat sink for the solar cells, maintaining a low cell temperature so that solar cell efficiency remains high.

Mitigation of houses with extremely high indoor radon concentrations

International Nuclear Information System (INIS)

Jiranek, M.; Neznal, M.

2006-01-01

Full text of publication follows: The paper reports on the experience of the Czech Technical University in dealing with mitigation of houses in which unusually high indoor radon concentrations were found. The whole process of remediation is illustrated by example of an old single-family house that was built in the area formed by highly permeable soils with high radon content in the soil air. T he house has a small cellar located under 1/5 of the ground floor area. Two types of floors, i.e. timber floors and cracked concrete slabs were found in the house. As a result of extremely high radon concentration in the sub-floor region (up to 600 kBq/m 3 ) and leaky structures in contact with soil, radon concentrations around 100 kBq/m 3 in the cellar and up to 60 kBq/m 3 in the living rooms on the ground floor were measured prior to mitigation. Mitigation measures that were carried out in the house consist of reconstruction of timber floors and installation of active soil depressurization. Timber floors were replaced with concrete slab fitted with damp proof membrane, thermal insulation and floor covering. The soil depressurization system was made up of two sections. The first section is composed of the network of perforated pipes inserted in the drainage layer placed under the new floors and four perforated tubes drilled under the existing floors. The soil air from this section is extracted by means of a roof fan installed at the top of the vertical exhaust pipe running inside the living space and terminating above the roof. The second section was designed to withdraw by means of a small fan radon-laden air from the filling in the floor above the cellar and from perforated tubes drilled into the sub-floor region under the rooms adjacent to the cellar. It serves also for the active ventilation of the cellar. Pressure, temperature and radon concentration sensors were installed into the drainage layer during the reconstruction of floors to record variations in these

Concentration of High Level Radioactive Liquid Waste. Basic data acquisition

Energy Technology Data Exchange (ETDEWEB)

Juvenelle, A.; Masson, M.; Garrido, M.H. [DEN/VRH/DRCP/SCPS/LPCP, BP 17171 - 30207 Bagnols sur Ceze Cedex (France)

2008-07-01

Full text of publication follows: In order to enhance its knowledge about the concentration of high level liquid waste (HLLW) from the nuclear fuel reprocessing process, a program of studies was defined by Cea. In a large field of acidity, it proposes to characterize the concentrated solution and the obtained precipitates versus the concentration factor. Four steps are considered: quantification of the salting-out effect on the concentrate acidity, acquisition of solubility data, precipitates characterisation versus the concentration factor through aging tests and concentration experimentation starting from simulated fission products solutions. The first results, reported here, connect the acidity of the concentrated solution to the concentration factor and allow us to precise the field of acidity (4 to 12 N) for the next experiments. In this field, solubility data of various elements (Ba, Sr, Zr...) are separately measured at room temperature, in nitric acid in a first time, then in the presence of various species present in medium (TBP, PO{sub 4}{sup 3-}). The reactions between these various elements are then investigated (formation of insoluble mixed compounds) by following the concentration cations in solution and characterising the precipitates. (authors)

Impact of dopant metal ions in the framework of parent zirconia on the n-heptane isomerization activity of the Pt/WO3-ZrO2 catalysts

Czech Academy of Sciences Publication Activity Database

Kaucký, Dalibor; Sobalík, Zdeněk; Hidalgo, J. M.; Černý, R.; Bortnovský, O.

2016-01-01

Roč. 420, AUG 2016 (2016), s. 107-114 ISSN 0304-5102 R&D Projects: GA MPO FR-TI3/316 Institutional support: RVO:61388955 Keywords : zirconia * tungstated zirconia * dopants Subject RIV: CF - Physical ; Theoretical Chemistry

High surface hole concentration p-type GaN using Mg implantation

International Nuclear Information System (INIS)

Long Tao; Yang Zhijian; Zhang Guoyi

2001-01-01

Mg ions were implanted on Mg-doped GaN grown by metalorganic chemical vapor deposition (MOCVD). The p-type GaN was achieved with high hole concentration (8.28 x 10 17 cm -3 ) conformed by Van derpauw Hall measurement after annealing at 800 degree C for 1 h. this is the first experimental report of Mg implantation on Mg-doped GaN and achieving p-type GaN with high surface hole concentration

Rheology of dilute acid hydrolyzed corn stover at high solids concentration.

Science.gov (United States)

Ehrhardt, M R; Monz, T O; Root, T W; Connelly, R K; Scott, C T; Klingenberg, D J

2010-02-01

The rheological properties of acid hydrolyzed corn stover at high solids concentration (20-35 wt.%) were investigated using torque rheometry. These materials are yield stress fluids whose rheological properties can be well represented by the Bingham model. Yield stresses increase with increasing solids concentration and decrease with increasing hydrolysis reaction temperature, acid concentration, and rheometer temperature. Plastic viscosities increase with increasing solids concentration and tend to decrease with increasing reaction temperature and acid concentration. The solids concentration dependence of the yield stress is consistent with that reported for other fibrous systems. The changes in yield stress with reaction conditions are consistent with observed changes in particle size. This study illustrates that torque rheometry can be used effectively to measure rheological properties of concentrated biomass.

Analysis of anabolic steroids in urine by gas chromatography-microchip atmospheric pressure photoionization-mass spectrometry with chlorobenzene as dopant.

Science.gov (United States)

Hintikka, Laura; Haapala, Markus; Kuuranne, Tiia; Leinonen, Antti; Kostiainen, Risto

2013-10-18

A gas chromatography-microchip atmospheric pressure photoionization-tandem mass spectrometry (GC-μAPPI-MS/MS) method was developed for the analysis of anabolic androgenic steroids in urine as their trimethylsilyl derivatives. The method utilizes a heated nebulizer microchip in atmospheric pressure photoionization mode (μAPPI) with chlorobenzene as dopant, which provides high ionization efficiency by producing abundant radical cations with minimal fragmentation. The performance of GC-μAPPI-MS/MS was evaluated with respect to repeatability, linearity, linear range, and limit of detection (LOD). The results confirmed the potential of the method for doping control analysis of anabolic steroids. Repeatability (RSD<10%), linearity (R(2)≥0.996) and sensitivity (LODs 0.05-0.1ng/mL) were acceptable. Quantitative performance of the method was tested and compared with that of conventional GC-electron ionization-MS, and the results were in good agreement. Copyright © 2013 Elsevier B.V. All rights reserved.

Size limit on the phosphorous doped silicon nanocrystals for dopant activation

Energy Technology Data Exchange (ETDEWEB)

Yang, P., E-mail: pengyuan.yang@surrey.ac.uk [Surrey Ion Beam Centre, Advanced Technology Institute, University of Surrey, Guildford GU2 5XH (United Kingdom); Gwilliam, R.M. [Surrey Ion Beam Centre, Advanced Technology Institute, University of Surrey, Guildford GU2 5XH (United Kingdom); Crowe, I.F.; Papachristodoulou, N.; Halsall, M.P. [Photon Science Institute, School of Electrical and Electronic Engineering, Alan Turing Building, University of Manchester, Manchester M13 9PL (United Kingdom); Hylton, N.P. [Blackett Laboratory, Department of Physics, Imperial College London, London SW7 2AZ (United Kingdom); Hulko, O.; Knights, A.P. [Department of Engineering Physics and the Centre for Emerging Device Technologies, McMaster University, 1280 Main Street West, Hamilton L8S 4L7, Ontario (Canada); Shah, M.; Kenyon, A.J. [Department of Electronic and Electrical Engineering, University College London, London WC1E 7JE (United Kingdom)

2013-07-15

We studied the photoluminescence spectra of silicon nanocrystals doped with and without phosphorus as a function of isothermal annealing time. Silicon nanocrystals were prepared by the implantation of 80 keV Si{sup +} into a 500 nm SiO{sub 2} film to an areal density of 8 × 10{sup 16} at/cm{sup 2}. Half of the samples were co-implanted with P{sup +} at 80 keV to 5 × 10{sup 15} at/cm{sup 2}. The photoluminescence of the annealed samples were photo-excited at wavelength of 405 nm. For short anneal times, when the nanocrystal size distribution has a relatively small mean diameter, formation in the presence of phosphorus yields an increase in the luminescence intensity and a blue shift in the emission peak compared with intrinsic nanocrystals. As the mean size increases with annealing time, this enhancement rapidly diminishes and the peak energy shifts to the red. Our results indicate the donor electron generation depends strongly on the nanocrystal size. We also found a critical limit above which it allows dopant activation.

Prodigious Effects of Concentration Intensification on Nanoparticle Synthesis: A High-Quality, Scalable Approach

KAUST Repository

Williamson, Curtis B.

2015-12-23

© 2015 American Chemical Society. Realizing the promise of nanoparticle-based technologies demands more efficient, robust synthesis methods (i.e., process intensification) that consistently produce large quantities of high-quality nanoparticles (NPs). We explored NP synthesis via the heat-up method in a regime of previously unexplored high concentrations near the solubility limit of the precursors. We discovered that in this highly concentrated and viscous regime the NP synthesis parameters are less sensitive to experimental variability and thereby provide a robust, scalable, and size-focusing NP synthesis. Specifically, we synthesize high-quality metal sulfide NPs (<7% relative standard deviation for Cu2-xS and CdS), and demonstrate a 10-1000-fold increase in Cu2-xS NP production (>200 g) relative to the current field of large-scale (0.1-5 g yields) and laboratory-scale (<0.1 g) efforts. Compared to conventional synthesis methods (hot injection with dilute precursor concentration) characterized by rapid growth and low yield, our highly concentrated NP system supplies remarkably controlled growth rates and a 10-fold increase in NP volumetric production capacity (86 g/L). The controlled growth, high yield, and robust nature of highly concentrated solutions can facilitate large-scale nanomanufacturing of NPs by relaxing the synthesis requirements to achieve monodisperse products. Mechanistically, our investigation of the thermal and rheological properties and growth rates reveals that this high concentration regime has reduced mass diffusion (a 5-fold increase in solution viscosity), is stable to thermal perturbations (64% increase in heat capacity), and is resistant to Ostwald ripening.

First-principles study on ferromagnetism in double perovskite Sr2AlTaO6 doped with Cu or Zn at B sites

Science.gov (United States)

Li, Y. D.; Wang, C. C.; Guo, Y. M.; Yu, Y.; Lu, Q. L.; Huang, S. G.; Li, Q. J.; Wang, H.; Cheng, R. L.; Liu, C. S.

2018-05-01

The possibilities of ferromagnetism induced by nonmagnetic dopants (Cu, Zn) in double perovskite Sr2AlTaO6 at B sites are investigated by density functional theory. Calculations reveal that substitutions at Ta-site tend to form high spin electronic configurations and could induce ferromagnetism which can be attributed to the hole-mediated p- d hybridization between Cu (or Zn) eg states and the neighboring O 2p states. The dopants preferably substitute at Al-site and adopt low spin electronic structures. Due to the smaller hole concentration and weaker covalent intensity, Sr2AlTaO6 with dopants at Al-site exhibits p-type metallic semiconductors without spin polarization.

Diverse microbial species survive high ammonia concentrations

Science.gov (United States)

Kelly, Laura C.; Cockell, Charles S.; Summers, Stephen

2012-04-01

Planetary protection regulations are in place to control the contamination of planets and moons with terrestrial micro-organisms in order to avoid jeopardizing future scientific investigations relating to the search for life. One environmental chemical factor of relevance in extraterrestrial environments, specifically in the moons of the outer solar system, is ammonia (NH3). Ammonia is known to be highly toxic to micro-organisms and may disrupt proton motive force, interfere with cellular redox reactions or cause an increase of cell pH. To test the survival potential of terrestrial micro-organisms exposed to such cold, ammonia-rich environments, and to judge whether current planetary protection regulations are sufficient, soil samples were exposed to concentrations of NH3 from 5 to 35% (v/v) at -80°C and room temperature for periods up to 11 months. Following exposure to 35% NH3, diverse spore-forming taxa survived, including representatives of the Firmicutes (Bacillus, Sporosarcina, Viridibacillus, Paenibacillus, Staphylococcus and Brevibacillus) and Actinobacteria (Streptomyces). Non-spore forming organisms also survived, including Proteobacteria (Pseudomonas) and Actinobacteria (Arthrobacter) that are known to have environmentally resistant resting states. Clostridium spp. were isolated from the exposed soil under anaerobic culture. High NH3 was shown to cause a reduction in viability of spores over time, but spore morphology was not visibly altered. In addition to its implications for planetary protection, these data show that a large number of bacteria, potentially including spore-forming pathogens, but also environmentally resistant non-spore-formers, can survive high ammonia concentrations.

Comparison of GaP and PH3 as dopant sources for STM-based device fabrication

International Nuclear Information System (INIS)

Goh, Kuan Eng Johnson; Oberbeck, L; Butcher, M J; Curson, N J; Ruess, F J; Simmons, M Y

2007-01-01

We present a comparative study of the use of a GaP solid source as an alternative to gaseous PH 3 for controlled phosphorus δ-doping of lithographic patterns on H:Si(001) fabricated by scanning tunnelling microscopy (STM). Whilst our electrical studies show that P δ-doping of Si with the GaP solid source and gaseous PH 3 result in essentially the same electrical characteristics, our STM studies reveal that P 2 molecules from the GaP source exhibit a lower selectivity between bare Si(001) and H:Si(001) compared to PH 3 molecules. We discuss the significance of our findings in the context of fabricating nanoscale P dopant devices in Si using STM-based lithography

High frequency measurement of nitrate concentration in the Lower Mississippi River, USA

Science.gov (United States)

Duan, Shuiwang; Powell, Rodney T.; Bianchi, Thomas S.

2014-11-01

Nutrient concentrations in the Mississippi River have increased dramatically since the 1950s, and high frequency measurements on nitrate concentration are required for accurate load estimations and examinations on nitrate transport and transformation processes. This three year record of high temporal resolution (every 2-3 h) data clearly illustrates the importance of high frequency sampling in improving load estimates and resolving variations in nitrate concentration with river flow and tributary inputs. Our results showed large short-term (days to weeks) variations in nitrate concentration but with no diurnal patterns. A repeatable and pronounced seasonal pattern of nitrate concentration was observed, and showed gradual increases from the lowest values in September (during base-flow), to the highest in June - which was followed by a rapid decrease. This seasonal pattern was only moderately linked with water discharge, and more controlled by nitrogen transformation/export from watershed as well as mixing patterns of the two primary tributaries (the upper Mississippi and the Ohio Rivers), which have distinctly different nitrate concentrations and flow patterns. Based on continuous in situ flow measurements, we estimated 554-886 × 106 kg of nitrate-N was exported from the Mississippi River system during years 2004-2006, which was <9% and <16% lower than U.S. Geological Survey's (USGS) estimates using their LOADEST or composite methods, respectively. USGS methods generally overestimated nitrate loads during rising stages and underestimated the loads during falling stages. While changes in nitrate concentrations in large rivers are generally not as responsive to alterations in diurnal inputs and/or watershed hydrology as small rivers, high-frequency water quality sampling would help in monitoring short-term (days to weeks) variations in nutrient concentration patterns and thus improve the accuracy of nutrient flux estimates.

Evaluation of radionuclide concentrations in high-level radioactive wastes

International Nuclear Information System (INIS)

Fehringer, D.J.

1985-10-01

This report describes a possible approach for development of a numerical definition of the term ''high-level radioactive waste.'' Five wastes are identified which are recognized as being high-level wastes under current, non-numerical definitions. The constituents of these wastes are examined and the most hazardous component radionuclides are identified. This report suggests that other wastes with similar concentrations of these radionuclides could also be defined as high-level wastes. 15 refs., 9 figs., 4 tabs

High surface hole concentration p-type GaN using Mg implantation

CERN Document Server

Long Tao; Zhang Guo Yi

2001-01-01

Mg ions were implanted on Mg-doped GaN grown by metalorganic chemical vapor deposition (MOCVD). The p-type GaN was achieved with high hole concentration (8.28 x 10 sup 1 sup 7 cm sup - sup 3) conformed by Van derpauw Hall measurement after annealing at 800 degree C for 1 h. this is the first experimental report of Mg implantation on Mg-doped GaN and achieving p-type GaN with high surface hole concentration

Effect of additionally introduced Zn and Eu dopants on the photoluminescence spectra of Er-Doped GaN crystals

International Nuclear Information System (INIS)

Mezdrogina, M. M.; Krivolapchuk, V. V.; Petrov, V. N.; Rodin, S. N.; Cherenkov, A. V.

2006-01-01

It is shown that the effect of dopants on the photoluminescence spectrum depends on the conductivity type of the initial GaN crystals. Sensitization of emission is observed in wurtzite p-GaN crystals doped with Er. The same effect was previously observed in such crystals doped with Eu and Zn. In n-type GaN crystals sequentially doped with Eu, Zn, and Er, emission is observed in the visible (λ = 360-440 and 530-560 nm) and IR (λ = 1.54 μm) spectral regions

Tuning the electronic properties of armchair carbon nanoribbons by a selective boron doping

International Nuclear Information System (INIS)

Navarro-Santos, P; Ricardo-Chavez, J L; Lopez-Sandoval, R; Reyes-Reyes, M; Rivera, J L

2010-01-01

Armchair carbon nanoribbons (ACNRs) substitutionally doped with boron atoms are investigated in the framework of first-principles density functional theory. Different boron-boron arrangements and concentrations are considered in order to simulate possible aggregation patterns, their structural stability and electronic behavior are determined as a function of ribbon size. In agreement with previous studies, our results show that the dopant atoms have in general a preference for edge sites, but specific effects appear as a function of concentration that importantly modify the properties of the ribbons compared to the pristine case. Interesting tendencies are discovered as a function of dopant concentration that significantly affect the electronic properties of the ribbons. We have found that BC 3 island formation and edge doping are the most important factors for the structural stabilization of the ribbons with high boron concentration (>7%) whereas for the cases of low boron concentrations ( 3 island patterns give rise to highly localized B states on top of the Fermi level, resulting in semiconducting behavior. On the other hand, when the average distance between the B atoms increases beyond island stoichiometry, the localization of their states is reduced and the ribbons may become metallic due to a band crossing caused by the lowering of the Fermi level resulting from the positive charge doping. Thus, tuning the dopant interaction would be an appropriate way to tailor the electronic properties of the ribbons in a convenient manner in view of potential technological applications.

High Efficiency Nanostructured III-V Photovoltaics for Solar Concentrator Application

Energy Technology Data Exchange (ETDEWEB)

Hubbard, Seth

2012-09-12

The High Efficiency Nanostructured III-V Photovoltaics for Solar Concentrators project seeks to provide new photovoltaic cells for Concentrator Photovoltaics (CPV) Systems with higher cell efficiency, more favorable temperature coefficients and less sensitivity to changes in spectral distribution. The main objective of this project is to provide high efficiency III-V solar cells that will reduce the overall cost per Watt for power generation using CPV systems.This work is focused both on a potential near term application, namely the use of indium arsenide (InAs) QDs to spectrally "tune" the middle (GaAs) cell of a SOA triple junction device to a more favorable effective bandgap, as well as the long term goal of demonstrating intermediate band solar cell effects. The QDs are confined within a high electric field i-region of a standard GaAs solar cell. The extended absorption spectrum (and thus enhanced short circuit current) of the QD solar cell results from the increase in the sub GaAs bandgap spectral response that is achievable as quantum dot layers are introduced into the i-region. We have grown InAs quantum dots by OMVPE technique and optimized the QD growth conditions. Arrays of up to 40 layers of strain balanced quantum dots have been experimentally demonstrated with good material quality, low residual stain and high PL intensity. Quantum dot enhanced solar cells were grown and tested under simulated one sun AM1.5 conditions. Concentrator solar cells have been grown and fabricated with 5-40 layers of QDs. Testing of these devices show the QD cells have improved efficiency compared to baseline devices without QDs. Device modeling and measurement of thermal properties were performed using Crosslight APSYS. Improvements in a triple junction solar cell with the insertion of QDs into the middle current limiting junction was shown to be as high as 29% under one sun illumination for a 10 layer stack QD enhanced triple junction solar cell. QD devices have strong

Defect phase diagram for doping of Ga2O3

Science.gov (United States)

Lany, Stephan

2018-04-01

For the case of n-type doping of β-Ga2O3 by group 14 dopants (C, Si, Ge, Sn), a defect phase diagram is constructed from defect equilibria calculated over a range of temperatures (T), O partial pressures (pO2), and dopant concentrations. The underlying defect levels and formation energies are determined from first-principles supercell calculations with GW bandgap corrections. Only Si is found to be a truly shallow donor, C is a deep DX-like (lattice relaxed donor) center, and Ge and Sn have defect levels close to the conduction band minimum. The thermodynamic modeling includes the effect of association of dopant-defect pairs and complexes, which causes the net doping to decline when exceeding a certain optimal dopant concentration. The optimal doping levels are surprisingly low, between about 0.01% and 1% of cation substitution, depending on the (T, pO2) conditions. Considering further the stability constraints due to sublimation of molecular Ga2O, specific predictions of optimized pO2 and Si dopant concentrations are given. The incomplete passivation of dopant-defect complexes in β-Ga2O3 suggests a design rule for metastable doping above the solubility limit.

Starch source in high concentrate rations does not affect rumen pH, histamine and lipopolysaccharide concentrations in dairy cows