WorldWideScience

Sample records for high cross-link density

  1. Crosslink density, oxidation and chain scission in retrieved, highly cross-linked UHMWPE tibial bearings.

    Science.gov (United States)

    Reinitz, Steven D; Currier, Barbara H; Levine, Rayna A; Van Citters, Douglas W

    2014-05-01

    Irradiated, thermally stabilized, highly cross-linked UHMWPE bearings have demonstrated superior wear performance and improved in vitro oxidation resistance compared with terminally gamma-sterilized bearings, yet retrieval analysis reveals unanticipated in vivo oxidation in these materials despite fewer or no measurable free radicals. There has been little evidence to date that the oxidation mechanism in thermally stabilized materials is the same as that in conventional materials, and so it is unknown whether oxidation in these materials is leading to chain scission and a degradation of mechanical properties, molecular weight, and crosslink density. The aim of this study was to determine whether measured in vivo oxidation in retrieved, highly cross-linked tibial bearings corresponds with a decreasing crosslink density. Analysis of three tibial bearing materials revealed that crosslink density decreased following in vivo duration, and that the change in crosslink density was strongly correlated with oxidation. The results suggest that oxidation in highly cross-linked materials is causing chain scissions that may, in time, impact the material properties. If in vivo oxidation continues over longer durations, there is potential for a clinically significant degradation of mechanical properties.

  2. Effect of electron-irradiation on cross-link density and crystalline structure of low- and high-density polyethylene

    Science.gov (United States)

    Khonakdar, H. A.; Jafari, S. H.; Wagenknecht, U.; Jehnichen, D.

    2006-01-01

    Low- and high-density polyethylenes (LDPE and HDPE) were cross-linked in solid state by electron beam irradiation. Molar mass between cross-link joints, Mc, and cross-link density, ν, were calculated using rubber elasticity theory and hot set data. The results showed that the ν and creep modulus increased and creep strain and Mc decreased with increasing irradiation dose. As compared to HDPE, the LDPE had higher ν and lower Mc values at a similar irradiation dose. X-ray analysis and differential scanning calorimetry investigation of first heating cycle revealed no changes in crystalline structure of the irradiated samples. This was attributed to immobilization of radicals frozen in the crystalline phase. As a result of hindered mobility of the polymeric chains, these radicals were not able to cross-link the chains in the crystalline region. However, after melting of the crystals and during subsequent re-solidification process, different levels of crystallinity were developed depending on the applied irradiation dose. The irradiated samples with higher dose had lower crystallization and melting temperatures with reduced crystallinities. These confined crystallization behaviors, observed after a series of cooling and heating cycles, could be attributed to the decrease in the Mc values. The length of chain segment needed for usual crystallization by chain folding is decreased due to formation of cross-link joints and hence the crystallization process was hindered.

  3. High-density functionalization and cross-linking of DNA: "click" and "bis-click" cycloadditions performed on alkynylated oligonucleotides with fluorogenic anthracene azides.

    Science.gov (United States)

    Pujari, Suresh S; Ingale, Sachin A; Seela, Frank

    2014-10-15

    High density functionalization of DNA with ethynyl and octadiynyl side chains followed by CuAAC "click labeling" with 9-azidomethylanthracene was performed. Alkynyl DNA was also cross-linked with fluorogenic 9,10-bis-azidomethylanthracene employing the "bis-click" reaction. By this means the fluorescence of the anthracene moiety was imparted to the virtually nonfluorescent DNA. Phosphoramidites of 8-aza-7-deaza-2'-deoxyadenosine with short and long linker arms in a steric nondemanding 7-position were utilized in solid phase oligodeoxynucleotide synthesis. High density alkynylated DNA-without anthracene residues-was found to be of comparable stability with both long and short linker arms. High density anthracene functionalized DNA became less stable with the short linker compared to that with the long linker connectivity. Interstrand cross-linked homodimers constructed from alkynylated oligonucleotides with fluorogenic 9,10-bis-azidomethylanthracene were hybridized with complementary strands to form double helices. They are more stable when the linker was located at a terminus than in a central position. Short linker anthracene adducts were destabilizing compared to long linker adducts. The fluorogenic anthracene residues not only have a significant effect on the duplex stability, but also impart fluorescence to the species. Fluorescence of cross-linked double helices with long linker connectivity was quenched when the cross-link was in a terminal position and was dequenched when the linker was connecting the two double helices at the center of the molecule. The fluorescence of the anthracene cross-linked double helices was strongly increased (dequenched) when the correct base pair was formed, while no change occurred upon mismatch formation.

  4. Fabrication of Stretchable Nanocomposites with High Energy Density and Low Loss from Cross-Linked PVDF Filled with Poly(dopamine) Encapsulated BaTiO3.

    Science.gov (United States)

    Xie, Yunchuan; Yu, Yangyang; Feng, Yefeng; Jiang, Wanrong; Zhang, Zhicheng

    2017-01-25

    In this report, a simple solution-cast method was employed to prepare poly(dopamine) (PDA) encapsulated BaTiO3 (BT) nanoparticle (PDA@BT) filled composites using PVDF matrix cross-linked by the free radical initiator. The effects of both the particle encapsulation and matrix cross-linking on the mechanical and dielectric properties of the composites were carefully investigated. The results suggested that the introduction of BT particles improved permittivity of the composites to ∼30 at 100 Hz when particle contents of only 7 wt % were utilized. This was attributed to the enhanced polarization, which was induced by high permittivity ceramic particles. Compared to bare BT, PDA@BT particles could be dispersed more homogeneously in the matrix, and the catechol groups of PDA layer might form chelation with free ions present in the matrix. The latter might depress the ion conduction loss in the composites. Other results revealed that the formation of hydrogen-bonding between the PDA layer and the polymer, especially the chemical cross-linking across the matrix, resulted in increased Young' modulus by ∼25%, improved breakdown strength by ∼40%, and declined conductivity by nearly 1 order of magnitude when compared to BT filled composites. The composite films filled with PDA@BTs indicated greater energy storage capacities by nearly 190% when compared to the pristine matrix. More importantly, the excellent mechanical performance allowed the composite films to adopt uni- or biaxially stretching, a crucial feature required for the realization of high breakdown strength. This work provided a facile strategy for fabrication of flexible and stretchable dielectric composites with depressed dielectric loss and enhanced energy storage capacity at low filler loadings (<10 wt %).

  5. Influence of cross-link structure, density and mechanical properties in the mesoscale deformation mechanisms of collagen fibrils.

    Science.gov (United States)

    Depalle, Baptiste; Qin, Zhao; Shefelbine, Sandra J; Buehler, Markus J

    2015-12-01

    Collagen is a ubiquitous protein with remarkable mechanical properties. It is highly elastic, shows large fracture strength and enables substantial energy dissipation during deformation. Most of the connective tissue in humans consists of collagen fibrils composed of a staggered array of tropocollagen molecules, which are connected by intermolecular cross-links. In this study, we report a three-dimensional coarse-grained model of collagen and analyze the influence of enzymatic cross-links on the mechanics of collagen fibrils. Two representatives immature and mature cross-links are implemented in the mesoscale model using a bottom-up approach. By varying the number, type and mechanical properties of cross-links in the fibrils and performing tensile test on the models, we systematically investigate the deformation mechanisms of cross-linked collagen fibrils. We find that cross-linked fibrils exhibit a three phase behavior, which agrees closer with experimental results than what was obtained using previous models. The fibril mechanical response is characterized by: (i) an initial elastic deformation corresponding to the collagen molecule uncoiling, (ii) a linear regime dominated by molecule sliding and (iii) the second stiffer elastic regime related to the stretching of the backbone of the tropocollagen molecules until the fibril ruptures. Our results suggest that both cross-link density and type dictate the stiffness of large deformation regime by increasing the number of interconnected molecules while cross-links mechanical properties determine the failure strain and strength of the fibril. These findings reveal that cross-links play an essential role in creating an interconnected fibrillar material of tunable toughness and strength.

  6. An Investigation on Rheology of Peroxide Cross-linking of Low Density Polyethylene

    DEFF Research Database (Denmark)

    Ghasemi, Ismaeil; Rasmussen, Henrik K.; Szabo, Peter

    2005-01-01

    One of the most important post-reactor modifications of polyethylene is cross-linking. It improves some properties of polyethylene such as environmental stress cracking resistance, chemical and abrasion resistance, and service temperature. In this study, the effect of peroxide cross-linking on th......One of the most important post-reactor modifications of polyethylene is cross-linking. It improves some properties of polyethylene such as environmental stress cracking resistance, chemical and abrasion resistance, and service temperature. In this study, the effect of peroxide cross......-linking on the rheological behaviour of low density polyethylene was investigated by using a combination of creep test and differential scanning calorimeter (DSC) in isotherm condition. The used peroxide was di-cumyl peroxide and its concentration was 2 wt%. The experiments were carried out at 150,160, and 170 degrees C...

  7. Insights into the swelling process and drug release mechanisms from cross-linked pectin/high amylose starch matrices

    Directory of Open Access Journals (Sweden)

    Fernanda M. Carbinatto

    2014-02-01

    Full Text Available Cross-linked pectin/high amylose mixtures were evaluated as a new excipient for matrix tablets formulations, since the mixing of polymers and cross-linking reaction represent rational tools to reach materials with modulated and specific properties that meet specific therapeutic needs. Objective: In this work the influence of polymer ratio and cross-linking process on the swelling and the mechanism driving the drug release from swellable matrix tablets prepared with this excipient was investigated. Methods: Cross-linked samples were characterized by their micromeritic properties (size and shape, density, angle of repose and flow rate and liquid uptake ability. Matrix tablets were evaluated according their physical properties and the drug release rates and mechanisms were also investigated. Results: Cross-linked samples demonstrated size homogeneity and irregular shape, with liquid uptake ability insensible to pH. Cross-linking process of samples allowed the control of drug release rates and the drug release mechanism was influenced by both polymer ratio and cross-linking process. The drug release of samples with minor proportion of pectin was driven by an anomalous transport and the increase of the pectin proportion contributed to the erosion of the matrix. Conclusion: The cross-linked mixtures of high amylose and pectin showed a suitable excipient for slowing the drug release rates.

  8. Effects of alginate hydrogel cross-linking density on mechanical and biological behaviors for tissue engineering.

    Science.gov (United States)

    Jang, Jinah; Seol, Young-Joon; Kim, Hyeon Ji; Kundu, Joydip; Kim, Sung Won; Cho, Dong-Woo

    2014-09-01

    An effective cross-linking of alginate gel was made through reaction with calcium carbonate (CaCO3). We used human chondrocytes as a model cell to study the effects of cross-linking density. Three different pore size ranges of cross-linked alginate hydrogels were fabricated. The morphological, mechanical, and rheological properties of various alginate hydrogels were characterized and responses of biosynthesis of cells encapsulated in each gel to the variation in cross-linking density were investigated. Desired outer shape of structure was maintained when the alginate solution was cross-linked with the applied method. The properties of alginate hydrogel could be tailored through applying various concentrations of CaCO3. The rate of synthesized GAGs and collagens was significantly higher in human chondrocytes encapsulated in the smaller pore structure than that in the larger pore structure. The expression of chondrogenic markers, including collagen type II and aggrecan, was enhanced in the smaller pore structure. It was found that proper structural morphology is a critical factor to enhance the performance and tissue regeneration.

  9. THE EFFECTS OF HIGH DOSE IRRADIATION ON THE CROSS-LINKING OF VITAMIN E-BLENDED ULTRAHIGH MOLECULAR WEIGHT POLYETHYLENE

    Science.gov (United States)

    Oral, Ebru; Beckos, Christine Godleski; Malhi, Arnaz S.; Muratoglu, Orhun K.

    2008-01-01

    Vitamin E-stabilized, highly cross-linked ultrahigh molecular weight polyethylene (UHMWPE) is a promising oxidation and wear resistant UHMWPE with improved mechanical strength in comparison with the first generation, irradiated and melted UHMWPE. One approach of incorporating vitamin E in UHMWPE is through blending of vitamin E in UHMWPE powder followed by consolidation and radiation crosslinking. However radiation crosslinking efficiency of UHMWPE decreases in the presence of vitamin E. Therefore an optimum vitamin E concentration and radiation dose level needs to be determined to achieve a cross-link density comparable to 100-kGy irradiated and melted UHMWPE, which has shown excellent wear properties in vivo. We investigated the cross-link density and mechanical properties of vitamin E-blended UHMWPEs as a function of vitamin E concentration in the blend and gamma irradiation doses up to 200 kGy. We found that 0.3 wt% vitamin E-blended UHMWPE could not be cross-linked above a cross-link density achieved at a radiation dose of 65 kGy for virgin UHMWPE and 1.0 wt% vitamin E-blended UHMWPE could not be cross-linked above a cross-link density achieved at a radiation dose of 25 kGy for virgin UHMWPE even when the former were irradiated to a radiation dose of 200 kGy. In addition, higher plasticity at vitamin E concentrations at and above 0.3 wt% indicated that increased chain scissioning may be prevalent. Since the wear resistance of this irradiated UHMWPE would be expected to be low, vitamin E concentrations equal to or above 0.3 wt% are not recommended for subsequent irradiation to achieve a wear resistant cross-linked UHMWPE. The long–term oxidative stability of irradiated blends with low vitamin E concentrations has yet to be studied to determine an optimum between cross-link density and long-term oxidative stability. PMID:18514813

  10. Radiation cross-linking in ultra-high molecular weight polyethylene for orthopaedic applications

    OpenAIRE

    Oral, Ebru; Muratoglu, Orhun K.

    2007-01-01

    The motivation for radiation cross-linking of ultra-high molecular weight polyethylene (UHMWPE) is to increase its wear resistance to be used as bearing surfaces for total joint arthroplasty. However, radiation also leaves behind long-lived residual free radicals in this polymer, the reactions of which can detrimentally affect mechanical properties. In this review, we focus on the radiation cross-linking and oxidative stability of first and second generation highly cross-linked UHMWPEs develo...

  11. Cross-linking density alters early metabolic activities in chondrocytes encapsulated in poly(ethylene glycol) hydrogels and cultured in the rotating wall vessel.

    Science.gov (United States)

    Villanueva, Idalis; Klement, Brenda J; von Deutsch, Daniel; Bryant, Stephanie J

    2009-03-01

    In designing a tissue engineering strategy for cartilage repair, selection of both the bioreactor, and scaffold is important to the development of a mechanically functional tissue. The hydrodynamic environment associated with many bioreactors enhances nutrient transport, but also introduces fluid shear stress, which may influence cellular response. This study examined the combined effects of hydrogel cross-linking and the hydrodynamic environment on early chondrocyte response. Specifically, chondrocytes were encapsulated in poly(ethylene glycol) (PEG) hydrogels having two different cross-linked structures, corresponding to a low and high cross-linking density. Both cross-linked gels yielded high water contents (92% and 79%, respectively) and mesh sizes of 150 and 60 A respectively. Cell-laden PEG hydrogels were cultured in rotating wall vessels (RWV) or under static cultures for up to 5 days. Rotating cultures yielded low fluid shear stresses (production, and matrix deposition for glycosaminoglycans (GAG). In static cultures, gel cross-linking had no effect on DNA content, NO production, or GAG production; although GAG production increased with culture time for both cross-linked gels. In rotating cultures, DNA content increased, NO production decreased, and overall GAG production decreased when compared to static controls for the low cross-linked gels. For the high cross-linked gels, the hydrodynamic environment had no effect on DNA content, but exhibited similar results to the low cross-linked gel for NO production, and matrix production. Our findings demonstrated that at early culture times, when there is limited matrix production, the hydrodynamic environment dramatically influences cell response in a manner dependent on the gel cross-linking, which may impact long-term tissue development.

  12. Coarse-Grained Molecular Dynamics Study of the Curing and Properties of Highly Cross-Linked Epoxy Polymers.

    Science.gov (United States)

    Aramoon, Amin; Breitzman, Timothy D; Woodward, Christopher; El-Awady, Jaafar A

    2016-09-08

    In this work, a coarse-grained model is developed for highly cross-linked bisphenol A diglycidyl ether epoxy resin with diaminobutane hardener. In this model, all conformationally relevant coarse-grained degrees of freedom are accounted for by sampling over the free-energy surfaces of the atomic structures using quantum mechanical simulations. The interaction potentials between nonbonded coarse-grained particles are optimized to accurately predict the experimentally measured density and glass-transition temperature of the system. In addition, a new curing algorithm is also developed to model the creation of highly cross-linked epoxy networks. In this algorithm, to create a highly cross-linked network, the reactants are redistributed from regions with an excessive number of reactive molecules to regions with a lower number of reactants to increase the chances of cross-linking. This new algorithm also dynamically controls the rate of cross-linking at each local region to ensure uniformity of the resulting network. The curing simulation conducted using this algorithm is able to develop polymeric networks having a higher average degree of cross-linking, which is more uniform throughout the simulation cell as compared to that in the networks cured using other curing algorithms. The predicted gel point from the current curing algorithm is in the acceptable theoretical and experimental range of measured values. Also, the resulting cross-linked microstructure shows a volume shrinkage of 5%, which is close to the experimentally measured volume shrinkage of the cured epoxy. Finally, the thermal expansion coefficients of materials in the glassy and rubbery states show good agreement with the experimental values.

  13. Sorption of substituted indoles on highly cross-linked polystyrene from water-acetonitrile solutions

    Science.gov (United States)

    Shafigulin, R. V.; Myakishev, A. A.; Il'Ina, E. A.; Il'in, M. M.; Davankov, V. A.; Bulanova, A. V.

    2011-07-01

    The sorption of first synthesized indole derivatives by highly cross-linked polystyrenes from water-acetonitrile solutions was studied by high-performance liquid chromatography. The retention factors and differences in the Gibbs energy of adsorption from infinite diluted solutions were calculated, and the applicability of the Snyder-Soczewinski and Scott-Kucera models for describing the chromatographic retention of sorbates on a polymer network of highly cross-linked polystyrene was shown.

  14. PROSPECTS OF HIGH-CURRENT ELECTRON BEAMS APPLICATION TO RADIATION POLYETHYLENE CROSS-LINKING

    Directory of Open Access Journals (Sweden)

    A.G. Gurin

    2013-09-01

    Full Text Available A possibility of applying a pulse-periodic high-current induction electron accelerators to radiation polyethylene cross-linking is considered in the article. A comparative analysis with other devices used for irradiation is made.

  15. Highly stable ionic-covalent cross-linked sulfonated poly(ether ether ketone) for direct methanol fuel cells

    Science.gov (United States)

    Lei, Linfeng; Zhu, Xingye; Xu, Jianfeng; Qian, Huidong; Zou, Zhiqing; Yang, Hui

    2017-05-01

    A novel ionic cross-linked sulfonated poly(ether ether ketone) containing equal content of sulfonic acid and pendant tertiary amine groups (TA-SPEEK) has been initially synthesized for the application in direct methanol fuel cells (DMFCs). By adjusting the ratio of p-xylene dibromide to tertiary amine groups of TA-SPEEK, a series of ionic-covalent cross-linked membranes (C-SPEEK-x) with tunable degree of cross-linking are prepared. Compared with the pristine membrane, the ionic and ionic-covalent cross-linked proton exchange membranes (PEMs) exhibit reduced methanol permeability and improved mechanical properties, dimensional and oxidative stability. The proton conductivity and methanol selectivity of protonated TA-SPEEK and C-SPEEK-x at 25 °C is up to 0.109 S cm-1 and 3.88 × 105 S s cm-3, respectively, which are higher than that of Nafion 115. The DMFC incorporating C-SPEEK-25 exhibits a maximum power density as high as 35.3 mW cm-2 with 4 M MeOH at 25 °C (31.8 mW cm-2 for Nafion 115). Due to the highly oxidative stability of the membrane, no obvious performance degradation of the DMFC is observed after more than 400 h operation, indicating such cost-effective ionic-covalent cross-linked membranes have substantial potential as alternative PEMs for DMFC applications.

  16. Vitamin E-diffused highly cross-linked UHMWPE particles induce less osteolysis compared to highly cross-linked virgin UHMWPE particles in vivo

    DEFF Research Database (Denmark)

    Bichara, David A; Malchau, Erik; Sillesen, Nanna H

    2014-01-01

    when compared to virgin gamma irradiated cross-linked UHMWPE. Groups received equal amount of particulate debris overlaying the calvarium for 10 days. Calvarial bone was examined using high resolution micro-CT and histomorphometric analyses. There was a statistically significant difference between...... virgin (12.2%±8%) and VE-UHMWPE (3%±1.4%) groups in regards to bone resorption (P=0.005) and inflammatory fibrous tissue overlaying the calvaria (0.48 vs. 0.20, P

  17. Vitamin E-diffused highly cross-linked UHMWPE particles induce less osteolysis compared to highly cross-linked virgin UHMWPE particles in vivo.

    Science.gov (United States)

    Bichara, David A; Malchau, Erik; Sillesen, Nanna H; Cakmak, Selami; Nielsen, G Petur; Muratoglu, Orhun K

    2014-09-01

    Recent in vitro findings suggest that UHMWPE wear particles containing vitamin E (VE) may have reduced biologic activity and decreased osteolytic potential. We hypothesized that particles from VE-stabilized, radiation cross-linked UHMWPE would cause less osteolysis in a murine calvarial bone model when compared to virgin gamma irradiated cross-linked UHMWPE. Groups received equal amount of particulate debris overlaying the calvarium for 10 days. Calvarial bone was examined using high resolution micro-CT and histomorphometric analyses. There was a statistically significant difference between virgin (12.2%±8%) and VE-UHMWPE (3%±1.4%) groups in regards to bone resorption (P=0.005) and inflammatory fibrous tissue overlaying the calvaria (0.48 vs. 0.20, PUHMWPE particles have reduced osteolytic potential in vivo when compared to virgin UHMWPE.

  18. Comparison of Wear and Oxidation in Retrieved Conventional and Highly Cross-Linked UHMWPE Tibial Inserts.

    Science.gov (United States)

    Currier, Barbara H; Currier, John H; Franklin, Katherine J; Mayor, Michael B; Reinitz, Steven D; Van Citters, Douglas W

    2015-12-01

    Two groups of retrieved tibial inserts from one manufacturer's knee system were analyzed to evaluate the effect of a highly cross-linked bearing surface on wear and in vivo oxidation. The two groups ((1) conventional gamma-inert sterilized and (2) highly cross-linked, coupled with the same rough (Ra=0.25) Ti-6Al-4V tray) were matched with statistically similar in vivo duration and patient variables. The retrieved inserts were analyzed for ketone oxidation and wear in the form of dimensional change. The difference in oxidation rate between highly cross-linked and conventional gamma-inert sterilized inserts did not reach statistical significance. Observations suggest that the majority of wear can be accounted for by the backside interface with the rough Ti-6Al-4V tray; however, wear measured by thickness-change rate was statistically indistinguishable between the two bearing materials.

  19. Cross-linked aromatic cationic polymer electrolytes with enhanced stability for high temperature fuel cell applications

    DEFF Research Database (Denmark)

    Ma, Wenjia; Zhao, Chengji; Yang, Jingshuai

    2012-01-01

    Diamine-cross-linked membranes were prepared from cross-linkable poly(arylene ether ketone) containing pendant cationic quaternary ammonium group (QPAEK) solution by a facile and general thermal curing method using 4,4′-diaminodiphenylmethane with rigid framework and 1,6-diaminohexane with flexible...... framework as cross-linker, respectively. Self-cross-linked cationic polymer electrolytes membranes were also prepared for comparison. The diamines were advantageously distributed within the polymeric matrix and its amine function groups interacted with the benzyl bromide of QPAEK, resulting in a double...... that the diamine-cross-linked membranes using the rigid cross-linker show much improved properties than that using the flexible cross-linker. More properties relating to the feasibility in high temperature proton exchange membrane fuel cell applications were investigated in detail....

  20. Influence of ethanol concentration on softening tests for cross-link density evaluation of dental composites

    Directory of Open Access Journals (Sweden)

    Rafael Ratto de Moraes

    2007-03-01

    Full Text Available This study investigated the influence of ethanol concentration on softening tests for cross-link density evaluation (microhardness of dental composites. Specimens of Filtek Z100 (3M ESPE were light-activated by standard or pulse-delay methods. After initial Knoop hardness readings (KHN1, half of specimens (n = 10 for each irradiation method was stored in 100% ethanol, and half in 75% ethanol, during 24 hours, and hardness was determined anew. Hardness deterioration (DKHN was recorded as the difference between pre and post-storage values. KHN1 data were submitted to one-way ANOVA and Tukey's test (alpha = 0.05, and hardness deterioration was analyzed by two-way ANOVA and Tukey's test (alpha= 0.05. For KHN1, no significant differences were detected between the activation modes (p = 0.697. Samples light-activated by the pulse-delay method presented significantly higher softening compared to the standard mode when samples were immersed in 100% ethanol. Conversely, no significant differences between curing modes were detected for samples stored in 75% ethanol.

  1. Vitamin E diffused highly cross-linked polyethylene in total hip arthroplasty at five years

    DEFF Research Database (Denmark)

    Nebergall, Audrey K; Greene, M. E.; Laursen, M B

    2017-01-01

    AIMS: The objective of this five-year prospective, blinded, randomised controlled trial (RCT) was to compare femoral head penetration into a vitamin E diffused highly cross-linked polyethylene (HXLPE) liner with penetration into a medium cross-linked polyethylene control liner using radiostereome......AIMS: The objective of this five-year prospective, blinded, randomised controlled trial (RCT) was to compare femoral head penetration into a vitamin E diffused highly cross-linked polyethylene (HXLPE) liner with penetration into a medium cross-linked polyethylene control liner using...... radiostereometric analysis. PATIENTS AND METHODS: Patients scheduled for total hip arthroplasty (THA) were randomised to receive either the study E1 (32 patients) or the control ArComXL polyethylene (35 patients). The median age (range) of the overall cohort was 66 years (40 to 76). RESULTS: The five-year median...... (interquartile range) proximal femoral head penetration into the E1 was -0.05 mm (-0.13 to -0.02) and 0.07 mm (-0.03 to 0.16) for ArComXL. At three and five years, the penetration was significantly greater in the ArComXL group compared with the E1 group (p = 0.029 and p = 0.019, respectively). All patient...

  2. Dynamic Heterogeneity in Highly Cross-linked Epoxy in the Vicinity of Glass Transition

    Science.gov (United States)

    Lin, Po-Han; Khare, Rajesh

    2010-03-01

    Cross-linked epoxy has been widely used in aerospace and electronics industries. The highly cross-linked nature of these systems leads to different chain dynamics as compared to the linear polymeric systems. In this work, we have used molecular dynamics (MD) simulations to study the dynamic heterogeneity in cross-linked epoxy near the glass transition temperature. Well-relaxed atomistic models of cross-linked epoxy were first created by employing the simulated annealing polymerization approach. The specific epoxy system studied consisted of diglycidyl ether of bisphenol-A (DGEBA) as the epoxy monomer and trimethylene glycol di-p-aminobenzoate (TMAB) as the cross-linker. The glass transition temperature of these model structures was determined from MD simulation by monitoring their volume-temperature behaviour in a stepwise cooling run. The chain dynamics of these systems were characterized by their local translational and orientational mobility. Furthermore, dynamic heterogeneity was studied by analyzing the spatial distribution of the mobile and immobile atoms in the system near the glass transition temperature.

  3. Wear measurement of highly cross-linked UHMWPE using a 7Be tracer implantation technique.

    Science.gov (United States)

    Wimmer, Markus A; Laurent, Michel P; Dwiwedi, Yasha; Gallardo, Luis A; Chipps, Kelly A; Blackmon, Jeffery C; Kozub, Raymond L; Bardayan, Daniel W; Gross, Carl J; Stracener, Daniel W; Smith, Michael S; Nesaraja, Caroline D; Erikson, Luke; Patel, Nidhi; Rehm, Karl E; Ahmad, Irshad; Greene, John P; Greife, Uwe

    2013-04-01

    The very low wear rates achieved with the current highly cross-linked ultrahigh molecular weight polyethylenes (UHMWPE) used in joint prostheses have proven to be difficult to measure accurately by gravimetry. Tracer methods are therefore being explored. The purpose of this study was to perform a proof-of-concept experiment on the use of the radioactive tracer beryllium-7 ((7)Be) for the determination of in vitro wear in a highly cross-linked orthopedic UHMWPE. Three cross-linked and four conventional UHMWPE pins made from compression-molded GUR 1050, were activated with 10(9) to 10(10) (7)Be nuclei using a new implantation setup that produced a homogenous distribution of implanted nuclei up to 8.5 μm below the surface. The pins were tested for wear in a six-station pin-on-flat apparatus for up to 7.1 million cycles (178 km). A Germanium gamma detector was employed to determine activity loss of the UHMWPE pins at preset intervals during the wear test. The wear of the cross-linked UHMWPE pins was readily detected and estimated to be 17 ± 3 μg per million cycles. The conventional-to-cross-linked ratio of the wear rates was 13.1 ± 0.8, in the expected range for these materials. Oxidative degradation damage from implantation was negligible; however, a weak dependence of wear on implantation dose was observed limiting the number of radioactive tracer atoms that can be introduced. Future applications of this tracer technology may include the analysis of location-specific wear, such as loss of material in the post or backside of a tibial insert.

  4. Molecular dynamics simulations of highly cross-linked polymer networks: prediction of thermal and mechanical properties

    Science.gov (United States)

    Shenogina, Natalia; Tsige, Mesfin; Mukhopadhyay, Sharmila; Patnaik, Soumya

    2012-02-01

    We use all-atom molecular dynamics (MD) simulations to predict the mechanical and thermal properties of thermosetting polymers. Atomistic simulation is a promising tool which can provide detailed structure-property relationships of densely cross-linked polymer networks. In this work we study the thermo-mechanical properties of thermosetting polymers based on amine curing agents and epoxy resins and have focused on the DGEBA/DETDA epoxy system. At first we describe the modeling approach to construction of realistic all-atom models of densely cross-linked polymer matrices. Subsequently, a series of atomistic simulations was carried out to examine the simulation cell size effect as well as the role of cross-linking density and chain length of the resin strands on thermo-mechanical properties at different temperatures. Two different methods were used to deform the polymer networks. Both static and dynamic approaches to calculating the mechanical properties were considered and the thermo-mechanical properties obtained from our simulations were found in reasonable agreement with experimental values.

  5. Flammability of radiation cross-linked low density polyethylene as an insulating material for wire and cable

    Science.gov (United States)

    Basfar, A. A.

    2002-03-01

    Various formulations of low-density polyethylene blended with ethylene vinyl acetate were prepared to improve the flame retardancy for wire and cable applications. The prepared formulations were cross-linked by γ-rays to 50, 100, 150 and 200 kGy in the presence of trimethylolpropane triacrylate (TMPTA). The effect of thermal aging on mechanical properties of these formulations were investigated. In addition, the influence of various combinations of aluminum trihydroxide and zinc borate as flame retardant fillers on the flammability was explored. Limiting oxygen index (LOI) and average extent of burning were used to characterize the flammability of investigated formulations. An improved flame retardancy of low density polyethylene was achieved by various combinations of flame ratardant fillers and cross-linking by gamma radiation.

  6. Reasons for revision of first-generation highly cross-linked polyethylenes.

    Science.gov (United States)

    Kurtz, Steven M; Medel, Francisco J; MacDonald, Daniel W; Parvizi, Javad; Kraay, Matthew J; Rimnac, Clare M

    2010-09-01

    Over a 10-year period, we prospectively evaluated the reasons for revision of contemporary and highly cross-linked polyethylene formulations in amulticenter retrieval program. Two hundred twelve consecutive retrievals were classified as conventional gamma inert sterilized (n = 37), annealed (Cross fire,[Stryker Orthopedics, Mahwah, NJ] n = 72), or remelted (Longevity [Zimmer ,Warsaw, Ind], XLPE[Smith and Nephew, Memphis, Tenn], Durasul [Zimmer,Warsaw, Ind] n = 103) liners. The most frequent reasons for revision were loosening (35%), instability(28%), and infection (21%) and were not related to polyethylene formulation (P = .17). Annealed and remelted liners had comparable linear penetration rates(0.03 and 0.04 mm/y, respectively, on average), and these were significantly lower than the rate in conventional retrievals (0.11 mm/y, P ≤ .0005). This retrieval study including first-generation highly cross linked liners demonstrated lower wear than conventional polyethylene. Although loosening remained as the most prevalent reason for revision, we could not demonstrate a relationship between wear and loosening.The long-term clinical performance of first-generation highly cross-linked liners remains promising based on the midterm outcomes of the components documented in this study [corrected].

  7. Development of optimum process for electron beam cross-linking of high density polyethylene thermal energy storage pellets, process scale-up and production of application qualities of material

    Science.gov (United States)

    Salyer, I. O.

    1980-01-01

    The electron irradiation conditions required to prepare thermally from stable high density polyethylene (HDPE) were defined. The conditions were defined by evaluating the heat of fusion and the melting temperature of several HDPE specimens. The performance tests conducted on the specimens, including the thermal cycling tests in the thermal energy storage unit are described. The electron beam irradiation tests performed on the specimens, in which the total radiation dose received by the pellets, the electron beam current, the accelerating potential, and the atmospheres were varied, are discussed.

  8. Cross-linked multilayer-dye films deposited onto silica surfaces with high affinity for pepsin

    Science.gov (United States)

    Bucatariu, Florin; Ghiorghita, Claudiu-Augustin; Cocarta, Ana-Irina; Dragan, Ecaterina Stela

    2016-12-01

    Cross-linked thin films based on pH-responsive polymers with a specific ligand inside the organic layer are useful materials in separation processes or in fabrication of controlled delivery systems. Herein, we report the step-by-step deposition of polymer multilayers based on poly(ethyleneimine) (PEI), poly(acrylic acid) (PAA) and poly(sodium methacrylate) (PMAA) followed by the Congo red (CR) immobilization onto composite Daisogel silica microparticles and silicon wafers. The non-crosslinked composites were not stable in extreme basic medium (pH = 13), while thermal and chemical cross-linked samples with CR inside were stable over a wide range of pH. The interaction properties of different proteins [pepsin (PEP), lysozyme, trypsin, bovine serum albumin] with modified solid surfaces were followed by potentiometric titrations, UV and AFM measurements. Only the PEP macromolecules were sorbed onto the Daisogel composite microparticles with CR inside the cross-linked multilayer. The maximum sorbed amount was nearly 200 mg PEP/g Daisogel//(PEI/PAA)4.5 + CR. This high sorbed amount was in accordance with the AFM images, the average high and roughness increased drastically after the sorption of PEP.

  9. Preliminary clinical and radiographic results of large ceramic heads on highly cross-linked polyethylene.

    Science.gov (United States)

    Meftah, Morteza; Ebrahimpour, Prouskeh Bruce; He, Chuan; Ranawat, Amar S; Ranawat, Chitranjan S

    2011-06-14

    Data are limited regarding large ceramic femoral heads with highly cross-linked polyethylene. We hypothesized that large ceramic head articulation with highly cross-linked polyethylene is safe with a low wear rate, comparable to metal-on-highly cross-linked polyethylene.The study group comprised 63 patients (72 hips) who had undergone total hip replacement (THR) with ceramic-on-highly cross-linked polyethylene between April 2006 and March 2007 with a minimum 2-year follow-up. Postoperative Western Ontario and Mc-Master Universities Arthritis Index (WOMAC) and Hospital for Special Surgery (HSS) scores were used for clinical assessment. Six-week and 2-year radiographs were analyzed by 2 independent observers using Roman 1.70 software. Twenty-six patients (29 hips) had 32-mm and 37 patients (43 hips) had 36-mm Biolox delta ceramic femoral heads (Ceramtec, Plochingen, Germany). Mean patient age was 60.9 ± 8.9 years, and mean follow-up was 2.9 ± 0.5 years. Mean postoperative WOMAC and HSS hip scores were 30.4 and 36.6, respectively. Mean wear at 1 and 2 years postoperatively was 0.06 ± 0.28 and 0.006 ± 0.12 mm/yr for all hips, respectively. Mean wear at 1 and 2 years postoperatively for the 32-mm femoral head was 0.063 ± 0.278 and 0.007 ± 0.126 mm/yr, respectively, and for the 36-mm femoral head was 0.057 ± 0.292 and 0.006 ± 0.118 mm/yr, respectively. No patient had any clinical complications, such as reoperation, infection, fractures, or radiographic evidence of osteolysis or loosening. The early results of THR with large ceramic heads demonstrate high safety and efficacy. Our data with 2-year follow-up show low wear rates, similar to published data for metal-on-highly cross-linked polyethylene.

  10. Cross-linked comb-shaped anion exchange membranes with high base stability

    Energy Technology Data Exchange (ETDEWEB)

    Li, NW; Wang, LZ; Hickner, M

    2014-01-01

    A unique one-step cross-linking strategy that connects quaternary ammonium centers using Grubbs II-catalyzed olefin metathesis was developed. The cross-linked anion exchange membranes showed swelling ratios of less than 10% and hydroxide conductivities of 18 to 40 mS cm(- 1). Cross-linking improved the membranes' stability to hydroxide degradation compared to their non-cross-linked analogues.

  11. Biopolymers from vegetable oils via catalyst- and solvent-free "click" chemistry: effects of cross-linking density.

    Science.gov (United States)

    Hong, Jian; Luo, Qiang; Wan, Xianmei; Petrović, Zoran S; Shah, Bipin K

    2012-01-09

    New monomers were prepared by introducing the azide groups in castor, canola, corn, soybean, and linseed oils. Polymerization of the azidated oils with alkynated soybean oil under thermal "click" chemistry conditions (without using a solvent or a catalyst) yielded fully cross-linked elastomers (1-5) of almost the same density (1.05 × 10(-3) kg/m(3)). The degree of cross-linking gradually increased from the castor-derived polymer (220 mol/m(3)) to the linseed-derived polymer (683 mol/m(3)). A systematic correlation between the degree of cross-linking and the thermal and mechanical properties was observed in these biopolymers. Tensile strength (0.62-3.39 MPa) and glass transition temperature (-5 to 16 °C) increased and the linear thermal expansion coefficient decreased in the series from the canola-derived polymer (2) to the linseed-derived polymer (5). The castor-derived polymer (1) that possesses an additional hydroxyl group per fatty acid chain behaved differently.

  12. Cross-linked carbon network with hierarchical porous structure for high performance solid-state electrochemical capacitor

    Science.gov (United States)

    Cheng, Yongliang; Huang, Liang; Xiao, Xu; Yao, Bin; Hu, Zhimi; Li, Tianqi; Liu, Kang; Zhou, Jun

    2016-09-01

    The development of portable electronics strongly requires flexible, lightweight, and inexpensive energy-storage devices with high power density, long cycling stability, and high reliability. In this work, we prepare a flexible solid-state electrochemical capacitor using cross-linked hierarchical porous carbon network as electrode material via electrospinning and carbonization process. This device can reversibly deliver a maximum energy density of 10.18 W h/kg with excellent cycling stability which achieves 95% capacitance retention after 20000 charge/discharge cycles. Moreover, it also demonstrates outstanding mechanical flexibility and excellent capacitance retention even when the device is repeatedly bended 10000 cycles under 90°. All of these results suggest its promising perspective in flexible energy storage device.

  13. Study the adsorption of sulfates by high cross-linked polystyrene divinylbenzene anion-exchange resin

    Science.gov (United States)

    Fathy, Mahmoud; Moghny, Th. Abdel; Awadallah, Ahmed E.; El-Bellihi, Abdel-Hameed A.-A.

    2017-03-01

    In response to rising concerns about the effect of sulfate on water quality, human health, and agriculture, many jurisdictions around the world are imposing tighter regulations for sulfate discharge. This is driving the need for environmental compliance in industries like mining, metal processing, pulp and paper, sewage treatment, and chemical manufacturing. The sulfate removal from synthetic water by high cross-linked polystyrene divinylbenzene resin was studied at batch experiments in this study. The effect of pH, contact time, sulfates concentration, and adsorbent dose on the sulfate sequestration was investigated. The optimum conditions were studied on Saline water as a case study. The results showed that with increasing of the absorbent amount; contact time, and pH improve the efficiency of sulfate removal. The maximum sulfates uptake was obtained in pH and contact time 3.0 and 120 min, respectively. Also, with increasing initial concentration of sulfates in water, the efficiency of sulfate removal decreased. The obtained results in this study were matched with Freundlich isotherm and pseudo-second-order kinetic. The maximum adsorption capacity (Qm) and constant rate were found 0.318 (mg/g) and 0.21 (mg/g.min), respectively. This study also showed that in the optimum conditions, the sulfate removal efficiency from Saline water by 0.1 mg/L sulfates was 65.64 %. Eventually, high cross-linked polystyrene divinylbenzene resin is recommended as a suitable and low cost absorbent to sulfate removal from aqueous solutions.

  14. In vitro and in vivo characteristics of core-shell type nanogel particles: optimization of core cross-linking density and surface poly(ethylene glycol) density in PEGylated nanogels.

    Science.gov (United States)

    Tamura, Masato; Ichinohe, Satoshi; Tamura, Atsushi; Ikeda, Yutaka; Nagasaki, Yukio

    2011-09-01

    The biocompatibility and body distribution of PEGylated polyamine nanogels composed of chemically cross-linked poly(2-N,N-(diethylamino)ethyl methacrylate) (PEAMA) gel cores surrounded by poly(ethylene glycol) (PEG) chains were investigated to evaluate their feasibility as drug nanocarriers for systemic administration. PEGylated nanogels with different cross-linking densities (1, 2, and 5mol.%) were prepared to evaluate their biocompatibilities by in vitro cytotoxicity assay, hemolysis assay, and in vivo acute toxicity assay. The toxic effect of the PEGylated nanogels derived from polyamine gel cores was significantly reduced when the cross-linking density was increased, and those with a cross-linking density of 5mol.% showed a remarkably high median lethal dose (LD(50)) value >200mgkg(-1),despite the abundance of amino groups in the core. One hour after intravenous injection the PEGylated nanogels were found to have been eliminated from the systemic circulation, and less than 1% of the injected dose (ID) remained in the bloodstream. To improve the blood circulation time by increasing the surface PEG density of the PEGylated nanogels post-PEGylation of the PEGylated nanogels (via the Menschutkin reaction between tertiary amines of the PEAMA gel core and bromobenzyl-terminated short PEG) was carried out. A biodistribution study of these post-PEGylated nanogels revealed that the blood circulation time of the nanogels was definitely prolonged as the PEG content was increased. Therefore, the precise design of PEGylated nanogels with increased cross-linking densities in their polyamine gel cores and increased surface PEG densities seems promising for systemic applications. Copyright © 2011 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

  15. Highly cross-linked polyethylene in hip resurfacing arthroplasty: long-term follow-up.

    Science.gov (United States)

    Amstutz, Harlan C; Takamura, Karren M; Ebramzadeh, Edward; Le Duff, Michel J

    2015-01-01

    Highly cross-linked polyethylene (XLPE) has improved wear properties. This study reports the results of a small series of patients treated over 10 years ago with a metal-on-XLPE hip resurfacing.A total of 21 hips in 20 patients received a hip resurfacing with a cobalt-chromium metal femoral head and metal-backed acetabular cup lined with a XLPE insert and were retrospectively studied. Kaplan-Meier Survivorship was calculated.Five patients who had initial extreme cystic disease in the femoral head failed due to femoral loosening. Survivorship was 95.2% at 5 years and 81.0% at 10 years.We found that XLPE wear was not implicated in these failures, which were primarily attributed to poor bone quality of the femoral head, early bone preparation, cementing technique and excessive head reaming to near the neck diameter, necessitated for the implantation of a thick two-part socket.

  16. Physically Cross-linked Polymer Binder Induced by Reversible Acid-Base Interaction for High-Performance Silicon Composite Anodes.

    Science.gov (United States)

    Lim, Sanghyun; Chu, Hodong; Lee, Kukjoo; Yim, Taeeun; Kim, Young-Jun; Mun, Junyoung; Kim, Tae-Hyun

    2015-10-28

    Silicon is greatly promising for high-capacity anode materials in lithium-ion batteries (LIBs) due to their exceptionally high theoretical capacity. However, it has a big challenge of severe volume changes during charge and discharge, resulting in substantial deterioration of the electrode and restricting its practical application. This conflict requires a novel binder system enabling reliable cyclability to hold silicon particles without severe disintegration of the electrode. Here, a physically cross-linked polymer binder induced by reversible acid-base interaction is reported for high performance silicon-anodes. Chemical cross-linking of polymer binders, mainly based on acidic polymers including poly(acrylic acid) (PAA), have been suggested as effective ways to accommodate the volume expansion of Si-based electrodes. Unlike the common chemical cross-linking, which causes a gradual and nonreversible fracturing of the cross-linked network, a physically cross-linked binder based on PAA-PBI (poly(benzimidazole)) efficiently holds the Si particles even after the large volume changes due to its ability to reversibly reconstruct ionic bonds. The PBI-containing binder, PAA-PBI-2, exhibited large capacity (1376.7 mAh g(-1)), high Coulombic efficiency (99.1%) and excellent cyclability (751.0 mAh g(-1) after 100 cycles). This simple yet efficient method is promising to solve the failures relating with pulverization and isolation from the severe volume changes of the Si electrode, and advance the realization of high-capacity LIBs.

  17. Clinical safety and wear resistance of the phospholipid polymer-grafted highly cross-linked polyethylene liner.

    Science.gov (United States)

    Moro, Toru; Takatori, Yoshio; Tanaka, Sakae; Ishihara, Kazuhiko; Oda, Hiromi; Kim, Yoon Taek; Umeyama, Takashige; Fukatani, Eisei; Ito, Hideya; Kyomoto, Masayuki; Oshima, Hirofumi; Tanaka, Takeyuki; Kawaguchi, Hiroshi; Nakamura, Kozo

    2016-11-03

    To reduce the production of wear particles and subsequent aseptic loosening, we created a human articular cartilage-mimicked surface for a highly cross-linked polyethylene liner, whose surface grafted layer consisted of a biocompatible phospholipid polymer, poly(2-methacryloyloxyethyl phosphorylcholine). Although our previous in vitro findings showed that poly(2-methacryloyloxyethyl phosphorylcholine)-grafted particles were biologically inert and caused no subsequent bone resorptive responses, and poly(2-methacryloyloxyethyl phosphorylcholine) grafting markedly decreased wear in hip joint simulator tests, the clinical safety, and in vivo wear resistance of poly(2-methacryloyloxyethyl phosphorylcholine)-grafted highly cross-linked polyethylene liners remained open to question. Therefore, in the present study, we evaluated clinical and radiographic outcomes of poly(2-methacryloyloxyethyl phosphorylcholine)-grafted highly cross-linked polyethylene liners 5 years subsequent to total hip replacement in 68 consecutive patients. No reoperation was required for any reason, and no adverse events were associated with the implanted liners. The average Harris Hip Score increased from 38.6 preoperatively to 96.5 5 years postoperatively, and health-related quality of life, as indicated by the Short Form 36 Health Survey, improved. Radiographic analyses showed no periprosthetic osteolysis or implant migration. Between 1 and 5 years postoperatively, the mean steady-state wear rate was 0.002 mm/year, which represented a marked reduction relative to other highly cross-linked polyethylene liners, and appeared to be unaffected by patient-related or surgical factors. Although longer follow up is required, poly(2-methacryloyloxyethyl phosphorylcholine)-grafted highly cross-linked polyethylene liners improved mid-term clinical outcomes. The clinical safety and wear-resistance results are encouraging with respect to the improvement of long-term clinical outcomes with poly(2

  18. Highly Stable and Porous Cross-Linked Polymers for Efficient Photocatalysis

    Energy Technology Data Exchange (ETDEWEB)

    Xie, Zhigang; Wang, Cheng; deKrafft, Kathryn E.; Lin, Wenbin

    2011-02-23

    Porous cross-linked polymers (PCPs) with phosphorescent [Ru(bpy)₃]{sup 2+} and [Ir(ppy)₂(bpy)]{sup +} building blocks were obtained via octacarbonyldicobalt (Co₂(CO)₈)-catalyzed alkyne trimerization reactions. The resultant Ru- and Ir-PCPs exhibited high porosity with specific surface areas of 1348 and 1547 m²/g, respectively. They are thermally stable at up to 350 °C in air and do not dissolve or decompose in all solvents tested, including concentrated hydrochloric acid. The photoactive PCPs were shown to be highly effective, recyclable, and reusable heterogeneous photocatalysts for aza-Henry reactions, α-arylation of bromomalonate, and oxyamination of an aldehyde, with catalytic activities comparable to those of the homogeneous [Ru(bpy)₃]{sup 2+} and [Ir(ppy)₂(bpy)]{sup +} photocatalysts. This work highlights the potential of developing photoactive PCPs as highly stable, molecularly tunable, and recyclable and reusable heterogeneous photocatalysts for a variety of important organic transformations.

  19. Cross-linked Polyethylenimine as Potential DNA Vector for Gene Delivery with High Efficiency and Low Cytotoxicity

    Institute of Scientific and Technical Information of China (English)

    Wei DONG; Guang-Hui JIN; Shu-Feng LI; Qi-Ming SUN; Ding-Yuan MA; Zi-Chun HUA

    2006-01-01

    Polyethylenimine (PEI) has been known as an efficient gene carrier with the highest cationic charge potential. High transfection efficiency of PEI, along with its cytotoxicity, strongly depends on its molecular weight. To enhance its gene delivery efficiency and minimize cytotoxicity, we have synthesized small cross-linked PEI with biodegradable linkages and evaluated their transfection efficiencies in vitro. In this study, branched PEI with a molecular weight of 800 Da was cross-linked by small diacrylate [ 1,4-butanediol diacrylate or ethyleneglycol dimethacrylate (EGDMA)] for 2-6 h. The efficiencies of the cross-linked PEI in in vitro transfection of plasmid DNA containing enhanced green fluorescent protein (EGFP) reporter gene were assessed in melanoma B 16F10 cell line and other cell lines. Flow cytometry was used to quantify the cellular entry efficiency of plasmid and the transgene expression level. The cytotoxicities of the cross-linked PEI in these cells were evaluated by MTT assay. EGDMA-PEI 800-4h, a typical cross-linked PEI reported here, mediated a more efficient expression of reporter gene than the commercially available 25-kDa branched PEI control, and resulted in a 9-fold increase in gene delivery in B16F10 cells and a 16-fold increase in 293T cells, while no cytotoxicity was found at the optimized condition for gene delivery. Furthermore, the transfection activity of polyplexes was preserved in the presence of serum proteins.

  20. Three Year RSA Evaluation of Vitamin E Diffused Highly Cross-linked Polyethylene Liners and Cup Stability

    DEFF Research Database (Denmark)

    Sillesen, Nanna H; Greene, Meridith E; Nebergall, Audrey K;

    2015-01-01

    Vitamin E diffusion into highly cross-linked polyethylene (E-XLPE) is a method for enhancing oxidative stability of acetabular liners. The purpose of this study was to evaluate in vivo penetration of E-XLPE using radiostereometric analysis (RSA). Eighty-four hips were recruited into a prospective...

  1. Temperature dependence of creep compliance of highly cross-linked epoxy: A molecular simulation study

    Energy Technology Data Exchange (ETDEWEB)

    Khabaz, Fardin, E-mail: rajesh.khare@ttu.edu; Khare, Ketan S., E-mail: rajesh.khare@ttu.edu; Khare, Rajesh, E-mail: rajesh.khare@ttu.edu [Department of Chemical Engineering, Texas Tech University, Lubbock, TX 79409 (United States)

    2014-05-15

    We have used molecular dynamics (MD) simulations to study the effect of temperature on the creep compliance of neat cross-linked epoxy. Experimental studies of mechanical behavior of cross-linked epoxy in literature commonly report creep compliance values, whereas molecular simulations of these systems have primarily focused on the Young’s modulus. In this work, in order to obtain a more direct comparison between experiments and simulations, atomistically detailed models of the cross-linked epoxy are used to study their creep compliance as a function of temperature using MD simulations. The creep tests are performed by applying a constant tensile stress and monitoring the resulting strain in the system. Our results show that simulated values of creep compliance increase with an increase in both time and temperature. We believe that such calculations of the creep compliance, along with the use of time temperature superposition, hold great promise in connecting the molecular insight obtained from molecular simulation at small length- and time-scales with the experimental behavior of such materials. To the best of our knowledge, this work is the first reported effort that investigates the creep compliance behavior of cross-linked epoxy using MD simulations.

  2. Characteristics of highly cross-linked polyethylene wear debris in vivo.

    Science.gov (United States)

    Baxter, Ryan M; MacDonald, Daniel W; Kurtz, Steven M; Steinbeck, Marla J

    2013-04-01

    Despite the widespread implementation of highly cross-linked polyethylene (HXLPE) liners to reduce the clinical incidence of osteolysis, it is not known if the improved wear resistance will outweigh the inflammatory potential of HXLPE wear debris generated in vivo. Thus, we asked: What are the differences in size, shape, number, and biological activity of polyethylene wear particles obtained from primary total hip arthroplasty revision surgery of conventional polyethylene (CPE) versus remelted or annealed HXLPE liners? Pseudocapsular tissue samples were collected from revision surgery of CPE and HXLPE (annealed and remelted) liners, and digested using nitric acid. The isolated polyethylene wear particles were evaluated using scanning electron microscopy. Tissues from both HXLPE cohorts contained an increased percentage of submicron particles compared to the CPE cohort. However, the total number of particles was lower for both HXLPE cohorts, as a result there was no significant difference in the volume fraction distribution and specific biological activity (SBA; the relative biological activity per unit volume) between cohorts. In contrast, based on the decreased size and number of HXLPE wear debris there was a significant decrease in total particle volume (mm(3)/g of tissue). Accordingly, when the SBA was normalized by total particle volume (mm(3)/gm tissue) or by component wear volume rate (mm(3)/year), functional biological activity of the HXLPE wear debris was significantly decreased compared to the CPE cohort. Indications for this study are that the osteolytic potential of wear debris generated by HXLPE liners in vivo is significantly reduced by improvements in polyethylene wear resistance. Copyright © 2013 Wiley Periodicals, Inc.

  3. Characteristics of highly cross-linked polyethylene wear debris in vivo

    Science.gov (United States)

    Baxter, Ryan M.; MacDonald, Daniel W.; Kurtz, Steven M.; Steinbeck, Marla J.

    2014-01-01

    Despite the widespread implementation of highly cross-linked polyethylene (HXLPE) liners to reduce the clinical incidence of osteolysis, it is not known if the improved wear resistance will outweigh the inflammatory potential of HXLPE wear debris generated in vivo. Thus, we asked: What are the differences in size, shape, number, and biological activity of polyethylene wear particles obtained from primary total hip arthroplasty revision surgery of conventional polyethylene (CPE) versus remelted or annealed HXLPE liners? Pseudocapsular tissue samples were collected from revision surgery of CPE and HXLPE (annealed and remelted) liners, and digested using nitric acid. The isolated polyethylene wear particles were evaluated using scanning electron microscopy. Tissues from both HXLPE cohorts contained an increased percentage of submicron particles compared to the CPE cohort. However, the total number of particles was lower for both HXLPE cohorts, as a result there was no significant difference in the volume fraction distribution and specific biological activity (SBA; the relative biological activity per unit volume) between cohorts. In contrast, based on the decreased size and number of HXLPE wear debris there was a significant decrease in total particle volume (mm3/g of tissue). Accordingly, when the SBA was normalized by total particle volume (mm3/gm tissue) or by component wear volume rate (mm3/year), functional biological activity of the HXLPE wear debris was significantly decreased compared to the CPE cohort. Indications for this study are that the osteolytic potential of wear debris generated by HXLPE liners in vivo is significantly reduced by improvements in polyethylene wear resistance. PMID:23436587

  4. Wear Measurement of Highly Cross-linked UHMWPE using a 7Be Tracer Implantation Technique

    Energy Technology Data Exchange (ETDEWEB)

    Wimmer, Markus A. [Rush Uniiv. Medical Center; Laurent, Michael P. [Rush Univ. Medical Center; Dwivedi, Yasha [Rush Univ. Medical Center; Gallardo, Luis A. [Rush Univ. Medical Center; Chipps, K. [Colorado School of Mines, Golden; Blackmon, Jeffery C [Louisiana State University; Kozub, R. L. [Tennessee Technological University; Bardayan, Daniel W [ORNL; Gross, Carl J [ORNL; Stracener, Daniel W [ORNL; Smith, Michael Scott [ORNL; Nesaraja, Caroline D [ORNL; Erikson, Luke [Colorado School of Mines, Golden; Patel, Nidhi [Colorado School of Mines, Golden; Rehm, Karl E. [Argonne National Laboratory (ANL); Ahmad, Irshad [Argonne National Laboratory (ANL); Greene, John P. [Argonne National Laboratory (ANL); Greife, Uwe [Colorado School of Mines, Golden

    2013-01-01

    The very low wear rates achieved with the current highly cross-linked ultrahigh molecular weight polyethylenes (UHMWPE) used in joint prostheses have proven to be difficult to measure accurately by gravimetry. Tracer methods are there- fore being explored. The purpose of this study was to perform a proof-of-concept experiment on the use of the radioactive tracer beryllium-7 (7Be) for the determination of in vitro wear in a highly cross-linked orthopedic UHMWPE. Three cross-linked and four conventional UHMWPE pins made from compression- molded GUR 1050, were activated with 109 to 1010 7Be nuclei using a new implantation setup that produced a homogenous distribution of implanted nuclei up to 8.5 lm below the surface. The pins were tested for wear in a six-station pin-on-flat appara- tus for up to 7.1 million cycles (178 km). A Germanium gamma detector was employed to determine activity loss of the UHMWPE pins at preset intervals during the wear test. The wear of the cross-linked UHMWPE pins was readily detected and esti- mated to be 17 6 3 lg per million cycles. The conventional-to- cross-linked ratio of the wear rates was 13.1 6 0.8, in the expected range for these materials. Oxidative degradation dam- age from implantation was negligible; however, a weak depend- ence of wear on implantation dose was observed limiting the number of radioactive tracer atoms that can be introduced. Future applications of this tracer technology may include the analysis of location-specific wear, such as loss of material in the post or backside of a tibial insert.

  5. Cross-Linking Density and Temperature Effects on the Self-Assembly of SiO2-PNIPAAm Core-Shell Particles at Interfaces

    NARCIS (Netherlands)

    Nazli, Kadriye Oezlem; Pester, Christian W.; Konradi, Artjom; Boeker, Alexander; van Rijn, Patrick

    2013-01-01

    SiO2PNIPAAm coreshell microgels (PNIPAAm=poly(N-isopropylacrylamide)) with various internal cross-linking densities and different degrees of polymerization were prepared in order to investigate the effects of stability, packing, and temperature responsiveness at polarapolar interfaces. The effects w

  6. Cross-linking chemistry of squid beak.

    Science.gov (United States)

    Miserez, Ali; Rubin, Daniel; Waite, J Herbert

    2010-12-03

    In stark contrast to most aggressive predators, Dosidicus gigas (jumbo squids) do not use minerals in their powerful mouthparts known as beaks. Their beaks instead consist of a highly sclerotized chitinous composite with incremental hydration from the tip to the base. We previously reported l-3,4-dihydroxyphenylalanine (dopa)-histidine (dopa-His) as an important covalent cross-link providing mechanical strengthening to the beak material. Here, we present a more complete characterization of the sclerotization chemistry and describe additional cross-links from D. gigas beak. All cross-links presented in this report share common building blocks, a family of di-, tri-, and tetra-histidine-catecholic adducts, that were separated by affinity chromatography and high performance liquid chromatography (HPLC) and identified by tandem mass spectroscopy and proton nuclear magnetic resonance ((1)H NMR). The data provide additional insights into the unusually high cross-link density found in mature beaks. Furthermore, we propose both a low molecular weight catechol, and peptidyl-dopa, to be sclerotization agents of squid beak. This appears to represent a new strategy for forming hard tissue in animals. The interplay between covalent cross-linking and dehydration on the graded properties of the beaks is discussed.

  7. In vitro and in vivo characteristics of core–shell type nanogel particles: Optimization of core cross-linking density and surface poly(ethylene glycol) density in PEGylated nanogels

    OpenAIRE

    Tamura, Masato; Ichinohe, Satoshi; Tamura, Atsushi; Ikeda, Yutaka; Nagasaki, Yukio

    2011-01-01

    The biocompatibility and body distribution of PEGylated polyamine nanogels composed of chemically cross-linked poly(2-N,N-(diethylamino)ethyl methacrylate) (PEAMA) gel cores surrounded by poly(ethylene glycol) (PEG) chains were investigated to evaluate their feasibility as drug nanocarriers for systemic administration. PEGylated nanogels with different cross-linking densities (1, 2, and 5 mol.%) were prepared to evaluate their biocompatibilities by in vitro cytotoxicity assay, hemolysis assay...

  8. Effect of Cross-linking Density on Creep and Recovery Behavior in Epoxy-Based Shape Memory Polymers (SMEPs) for Structural Applications

    Science.gov (United States)

    Rao, Kavitha V.; Ananthapadmanabha, G. S.; Dayananda, G. N.

    2016-12-01

    Epoxy-based shape memory polymers (SMEPs) are gaining importance in the area of aerospace structures due to their high strength and stiffness which is a primary requirement for an SMEP in structural applications. The understanding of viscoelastic behavior of SMEPs is very essential to assess their shape memory effect. In the present work, three types of SMEPs with varying cross-linking densities were developed by curing an aromatic epoxy resin with aliphatic amines. Glass transition temperature ( T g) was measured for these SMEPs using advanced rheometric expansion system, and from the T g measurements, a range of temperatures from glassy to rubbery regimes were chosen. At selected temperatures, creep-recovery tests were performed in order to evaluate the viscoelastic behavior of SMEPs and also to investigate the effect of temperature on creep-recovery. Further, a three-parameter viscoelastic model (Zener) was used to fit the data obtained from experiments. Model parameters like moduli of the springs and viscosity of the dashpot were evaluated by curve fitting. Results revealed that Zener model was well suited to describe the viscoelastic behavior of SMEPs as a function of test temperatures.

  9. Drainage dynamics of thin liquid foam films containing soft PNiPAM microgels: influence of the cross-linking density and concentration.

    Science.gov (United States)

    Keal, L; Lapeyre, V; Ravaine, V; Schmitt, V; Monteux, C

    2016-12-21

    We investigate the drainage dynamics of thin liquid foam films containing PNiPAM microgel suspensions with two cross-linking densities (1.5 and 5 mol% BIS) and at two microgel concentrations (0.1 and 1% wt). For this purpose, we use a thin-film pressure balance apparatus that can apply a controlled and sudden hydrostatic pressure on a film, and record the subsequent film thinning as a function of time. Once the film thickness has reached a stationary value, we test the adhesion between the interfaces of the film by reducing the pressure and measuring the angle between the film and the meniscus. This angle increases on reduction of pressure for adhesive films, which resists the separation of their interfaces. Non-adhesive films separate easily, and the meniscus angle stays constant. At a low microgel concentration, the more densely cross-linked microgels (5 mol% BIS) tend to drain into more adhesive films than the more loosely cross-linked particles (1.5 mol% BIS). The adhesion results from particles that bridge the two air-water interfaces of the film and are shared between them. In these cases, the film, which is initially stabilized by a bilayer of microgel particles, rearrange to a state where the microgels bridge the interfaces. These results are discussed and compared with previous studies at a low concentration of microgels, which have shown that emulsions stabilized with densely cross-linked microgels are more adhesive and less resistant to mechanical stresses than those obtained with lower cross-linking densities. In addition, micron-scale depleted zones with no microgels are observed in the films stabilized with the 5 mol% BIS particles, which eventually lead to the rupture of the films. At 1% wt, the films drain slowly, are not adhesive and have the thickness of a bilayer of microgel; while at 0.1% wt, the films have the thickness of a monolayer of microgel, are adhesive and show bridging. From the thin liquid foam film thicknesses we extract a rough

  10. Graphene oxide-immobilized NH₂-terminated silicon nanoparticles by cross-linked interactions for highly stable silicon negative electrodes.

    Science.gov (United States)

    Sun, Cheng; Deng, Yuanfu; Wan, Lina; Qin, Xusong; Chen, Guohua

    2014-07-23

    There is a great interest in the utilization of silicon-based anodes for lithium-ion batteries. However, its poor cycling stability, which is caused by a dramatic volume change during lithium-ion intercalation, and intrinsic low electric conductivity hamper its industrial applications. A facile strategy is reported here to fabricate graphene oxide-immobilized NH2-terminated silicon nanoparticles (NPs) negative electrode (Si@NH2/GO) directed by hydrogen bonding and cross-linked interactions to enhance the capacity retention of the anode. The NH2-modified Si NPs first form strong hydrogen bonds and covalent bonds with GO. The Si@NH2/GO composite further forms hydrogen bonds and covalent bonds with sodium alginate, which acts as a binder, to yield a stable composite negative electrode. These two chemical cross-linked/hydrogen bonding interactions-one between NH2-modified Si NPs and GO, and another between the GO and sodium alginate-along with highly mechanically flexible graphene oxide, produced a robust network in the negative electrode system to stabilize the electrode during discharge and charge cycles. The as-prepared Si@NH2/GO electrode exhibits an outstanding capacity retention capability and good rate performance, delivering a reversible capacity of 1000 mAh g(-1) after 400 cycles at a current of 420 mA g(-1) with almost 100% capacity retention. The results indicated the importance of system-level strategy for fabricating stable electrodes with improved electrochemical performance.

  11. Highly Cross-Linked Polyethylene in Total Hip and Knee Replacement: Spatial Distribution of Molecular Orientation and Shape Recovery Behavior

    Directory of Open Access Journals (Sweden)

    Yasuhito Takahashi

    2014-01-01

    Full Text Available The present study investigated effects of processing procedures on morphology of highly cross-linked and re-melted UHMWPE (XLPE in total hip and knee arthroplasty (THA, TKA. The shape recovery behavior was also monitored via uniaxial compression test at room temperature after non-destructive characterizations of the in-depth microstructure by confocal/polarized Raman spectroscopy. The goal of this study was to relate the manufacturing-induced morphology to the in vivo micromechanical performance, and ultimately to explore an optimal structure in each alternative joint bearing. It was clearly confirmed that the investigated XLPE hip and knee implants, which were produced from different orthopaedic grade resins (GUR 1050 and GUR 1020, consisted of two structural regions in the as-received states: the near-surface transitional anisotropic layer (≈100 μm thickness and the bulk isotropic structural region. These XLPEs exhibited a different crystalline anisotropy and molecular texture within the near-surface layers. In addition, the knee insert showed a slightly higher efficiency of shape recovery against the applied strain over the hip liner owing to a markedly higher percentage of the bulk amorphous phase with intermolecular cross-linking. The quantitative data presented in this study might contribute to construct manufacturing strategies for further rationalized structures as alternative bearings in THA and TKA.

  12. Highly stable pyridinium-functionalized cross-linked anion exchange membranes for all vanadium redox flow batteries

    Science.gov (United States)

    Zeng, L.; Zhao, T. S.; Wei, L.; Zeng, Y. K.; Zhang, Z. H.

    2016-11-01

    It has recently been demonstrated that the use of anion exchange membranes (AEMs) in vanadium redox flow batteries (VRFBs) can reduce the migration of vanadium ions through the membrane due to the Donnan exclusion effect among the positively charged functional groups and vanadium ions. However, AEMs are plagued by low chemical stability in harsh chemical environments. Here we propose and fabricate a pyridinium-functionalized cross-linked AEM for VRFBs. The pyridinium-functionalized bromomethylated poly (2,6-dimethyl-1,4-phenylene oxide) exhibits a superior chemical stability as a result of the strengthened internal cross-linking networks and the chemical inertness of the polymer backbone. Therefore, the membrane exhibits littler decay in a harsh environment for 20 days during the course of an ex situ immersion test. A cycling test also demonstrates that the VRFB assembled with the membrane enable to retain 80% of the initial discharge capacity over 537 cycles with a capacity decay rate of 0.037% cycle-1. Meanwhile, the membrane also shows a low vanadium permeability and a reasonably high conductivity in supporting electrolytes. Hence, all the measurements and performance tests reported in this work suggest that the membrane is a promising AEM for redox flow batteries to achieve excellent cycling stability and superior cell performance.

  13. High removal rate of cross-linked SU-8 resist using hydrogen radicals generated by tungsten hot-wire catalyzer

    Energy Technology Data Exchange (ETDEWEB)

    Kono, Akihiko, E-mail: a.kono@neptune.kanazawa-it.ac.jp [Kanazawa Institute of Technology, 7-1 Ougigaoka, Nonoichi, Ishikawa 921-8501 (Japan); Arai, Yu; Maruoka, Takeshi; Yamamoto, Masashi; Goto, Yousuke; Takahashi, Seiji; Nishiyama, Takashi [Kanazawa Institute of Technology, 7-1 Ougigaoka, Nonoichi, Ishikawa 921-8501 (Japan); Horibe, Hideo [Osaka City University, Sugimoto, Sumiyoshiku, Osaka 558-8585 (Japan)

    2014-07-01

    This paper discusses the removal of chemically amplified negative-tone i-line resist SU-8 using hydrogen radicals generated by the catalytic decomposition of H{sub 2} molecules in H{sub 2}/N{sub 2} mixed gas (H{sub 2}:N{sub 2} = 10:90 vol.%) using a tungsten hot-wire catalyzer. SU-8 resists with exposure doses from 7 to 280 mJ/cm{sup 2} were removed by hydrogen radicals, although the SU-8 removal rate was independent of the exposure dose. The SU-8 removal rate increased with both substrate and catalyzer temperature, in addition to a decrease in the distance between the catalyzer and substrate. A high removal rate for cross-linked SU-8 with an exposure dose of 14 mJ/cm{sup 2} of approximately 4 μm/min was achieved with a catalyzer to substrate distance of 20 mm, and catalyzer and initial substrate temperatures of 2400 and 165 °C, respectively. - Highlights: • Chemically amplified negative-tone i-line resist SU-8 removed by hydrogen radicals • Hydrogen radicals generated by catalytic H{sub 2} decomposition using hot-wire catalyzer • The cross-linked SU-8 resist was removed at a rate of approximately 4 μm/min.

  14. Highly cross-linked polyethylene in total hip and knee replacement: spatial distribution of molecular orientation and shape recovery behavior.

    Science.gov (United States)

    Takahashi, Yasuhito; Masaoka, Toshinori; Pezzotti, Giuseppe; Shishido, Takaaki; Tateiwa, Toshiyuki; Kubo, Kosuke; Yamamoto, Kengo

    2014-01-01

    The present study investigated effects of processing procedures on morphology of highly cross-linked and re-melted UHMWPE (XLPE) in total hip and knee arthroplasty (THA, TKA). The shape recovery behavior was also monitored via uniaxial compression test at room temperature after non-destructive characterizations of the in-depth microstructure by confocal/polarized Raman spectroscopy. The goal of this study was to relate the manufacturing-induced morphology to the in vivo micromechanical performance, and ultimately to explore an optimal structure in each alternative joint bearing. It was clearly confirmed that the investigated XLPE hip and knee implants, which were produced from different orthopaedic grade resins (GUR 1050 and GUR 1020), consisted of two structural regions in the as-received states: the near-surface transitional anisotropic layer (≈100 μm thickness) and the bulk isotropic structural region. These XLPEs exhibited a different crystalline anisotropy and molecular texture within the near-surface layers. In addition, the knee insert showed a slightly higher efficiency of shape recovery against the applied strain over the hip liner owing to a markedly higher percentage of the bulk amorphous phase with intermolecular cross-linking. The quantitative data presented in this study might contribute to construct manufacturing strategies for further rationalized structures as alternative bearings in THA and TKA.

  15. Interplay between human high mobility group protein 1 and replication protein A on psoralen-cross-linked DNA

    DEFF Research Database (Denmark)

    Reddy, Madhava C; Christensen, Jesper; Vasquez, Karen M

    2005-01-01

    Human high mobility group box (HMGB) 1 and -2 proteins are highly conserved and abundant chromosomal proteins that regulate chromatin structure and DNA metabolism. HMGB proteins bind preferentially to DNA that is bent or underwound and to DNA damaged by agents such as cisplatin, UVC radiation......, and benzo[a]pyrenediol epoxide (BPDE). Binding of HMGB1 to DNA adducts is thought to inhibit nucleotide excision repair (NER), leading to cell death, but the biological roles of these proteins remain obscure. We have used psoralen-modified triplex-forming oligonucleotides (TFOs) to direct a psoralen-DNA...... interstrand cross-link (ICL) to a specific site to determine the effect of HMGB proteins on recognition of these lesions. Our results reveal that human HMGB1 (but not HMGB2) binds with high affinity and specificity to psoralen ICLs, and interacts with the essential NER protein, replication protein A (RPA...

  16. Mechanisms of plastic deformation in highly cross-linked UHMWPE for total hip components--the molecular physics viewpoint.

    Science.gov (United States)

    Takahashi, Yasuhito; Shishido, Takaaki; Yamamoto, Kengo; Masaoka, Toshinori; Kubo, Kosuke; Tateiwa, Toshiyuki; Pezzotti, Giuseppe

    2015-02-01

    Plastic deformation is an unavoidable event in biomedical polymeric implants for load-bearing application during long-term in-vivo service life, which involves a mass transfer process, irreversible chain motion, and molecular reorganization. Deformation-induced microstructural alterations greatly affect mechanical properties and durability of implant devices. The present research focused on evaluating, from a molecular physics viewpoint, the impact of externally applied strain (or stress) in ultra-high molecular weight polyethylene (UHMWPE) prostheses, subjected to radiation cross-linking and subsequent remelting for application in total hip arthroplasty (THA). Two different types of commercial acetabular liners, which belong to the first-generation highly cross-linked UHMWPE (HXLPE), were investigated by means of confocal/polarized Raman microprobe spectroscopy. The amount of crystalline region and the spatial distribution of molecular chain orientation were quantitatively analyzed according to a combined theory including Raman selection rules for the polyethylene orthorhombic structure and the orientation distribution function (ODF) statistical approach. The structurally important finding was that pronounced recrystallization and molecular reorientation increasingly appeared in the near-surface regions of HXLPE liners with increasing the amount of plastic (compressive) deformation stored in the microstructure. Such molecular rearrangements, occurred in response to external strains, locally increase surface cross-shear (CS) stresses, which in turn trigger microscopic wear processes in HXLPE acetabular liners. Thus, on the basis of the results obtained at the molecular scale, we emphasize here the importance of minimizing the development of irrecoverable deformation strain in order to retain the pristine and intrinsically high wear performance of HXLPE components.

  17. Three Year RSA Evaluation of Vitamin E Diffused Highly Cross-linked Polyethylene Liners and Cup Stability.

    Science.gov (United States)

    Sillesen, Nanna H; Greene, Meridith E; Nebergall, Audrey K; Nielsen, Poul T; Laursen, Mogens B; Troelsen, Anders; Malchau, Henrik

    2015-07-01

    Vitamin E diffusion into highly cross-linked polyethylene (E-XLPE) is a method for enhancing oxidative stability of acetabular liners. The purpose of this study was to evaluate in vivo penetration of E-XLPE using radiostereometric analysis (RSA). Eighty-four hips were recruited into a prospective 10-year RSA. This is the first evaluation of the multicenter cohort after 3-years. All patients received E-XLPE liners (E1, Biomet) and porous-titanium coated cups (Regenerex, Biomet). There was no difference (P=0.450) in median femoral head penetration into the E-XLPE liners at 3-years comparing cobalt-chrome heads (-0.028mm; inter-quartile range (IQR) - 0.065 to 0.047) with ceramic heads (-0.043mm, IQR - 0.143to0.042). The 3-year follow-up indicates minimal E-XLPE liner penetration regardless of head material and minimal early cup movement.

  18. Comparison of steady state femoral head penetration rates between two highly cross-linked polyethylenes in total hip arthroplasty.

    Science.gov (United States)

    Whittaker, John-Paul; Charron, Kory D; McCalden, Richard W; Macdonald, Steven J; Bourne, Robert B

    2010-08-01

    Given that the manufacture of highly cross-linked polyethylene (HXLPE) is not standardized, the behavior of these materials may vary. Our study compares minimum 5-year steady state femoral head penetration rates using the Martell method, in 2 HXPLEs produced by different manufacturers. Patients received a primary hip arthroplasty using an uncemented acetabular component with an HXLPE liner and a 28-mm femoral head. Forty-seven patients in group A received an HXLPE liner (Reflection XLPE, Smith and Nephew Inc, Memphis, Tenn), and 36 patients in group B received a different HXLPE liner (Longevity, Zimmer Inc, Warsaw, Ind). Average follow-up was 6.42 years in group A and 7.64 years in group B. The steady state head penetration rates were not significantly (P > .05) different between the HXPLE groups over the midterm with 0.026 mm/y and 0.025 mm/y in groups A and B, respectively.

  19. Wear in conventional and highly cross-linked polyethylene cups: a 5-year follow-up study.

    Science.gov (United States)

    Olyslaegers, Christophe; Defoort, Koen; Simon, Jean-Pierre; Vandenberghe, Luc

    2008-06-01

    Highly cross-linked polyethylene (XLPE) has been introduced in total hip arthroplasty in an effort to reduce polyethylene wear and the associated periprosthetic osteolysis. Our aim was to demonstrate these reduced wear rates in a 2-dimensional head penetration model and to perform a clinical comparison of both groups using the Harris Hip Score (and SF-36 questionnaire). Sixty hips with a Trilogy XLPE liner (Zimmer) were matched and compared to a control group of 20 conventional Trilogy PE liners (Zimmer). No differences in clinical outcome were seen, but a statistically significant reduction in linear wear was observed in the XLPEgroup, after 5 years. It is clear that, because of the reduction and stabilization of free radicals in polyethylene, a reduction in annual wear can be achieved.

  20. Cross-Linking Amine-Rich Compounds into High Performing Selective CO2 Absorbents

    Science.gov (United States)

    Andreoli, Enrico; Dillon, Eoghan P.; Cullum, Laurie; Alemany, Lawrence B.; Barron, Andrew R.

    2014-12-01

    Amine-based absorbents play a central role in CO2 sequestration and utilization. Amines react selectively with CO2, but a drawback is the unproductive weight of solvent or support in the absorbent. Efforts have focused on metal organic frameworks (MOFs) reaching extremely high CO2 capacity, but limited selectivity to N2 and CH4, and decreased uptake at higher temperatures. A desirable system would have selectivity (cf. amine) and high capacity (cf. MOF), but also increased adsorption at higher temperatures. Here, we demonstrate a proof-of-concept where polyethyleneimine (PEI) is converted to a high capacity and highly selective CO2 absorbent using buckminsterfullerene (C60) as a cross-linker. PEI-C60 (CO2 absorption of 0.14 g/g at 0.1 bar/90°C) is compared to one of the best MOFs, Mg-MOF-74 (0.06 g/g at 0.1 bar/90°C), and does not absorb any measurable amount of CH4 at 50 bar. Thus, PEI-C60 can perform better than MOFs in the sweetening of natural gas.

  1. Borate cross-linked graphene oxide-chitosan as robust and high gas barrier films

    Science.gov (United States)

    Yan, Ning; Capezzuto, Filomena; Lavorgna, Marino; Buonocore, Giovanna G.; Tescione, Fabiana; Xia, Hesheng; Ambrosio, Luigi

    2016-05-01

    Chitosan (CS) is one of the most promising polymers due to its biocompatibility, biodegradability, and natural abundance. However, its poor mechanical and barrier properties make it difficult to satisfy a wide range of applications. Herein, borate ions, originating from the hydrolysis of sodium tetraborate decahydrate (borax), have been used to crosslink chitosan and graphene oxide (GO) nanocomposites. Chitosan films consisting of 1.0 wt% boron and 1.0 wt% GO exhibit a significant improvement in both the toughness and oxygen barrier properties compared to pristine chitosan. In particular the tensile strength of the samples after thermal treatment increases by ~160% compared to pristine chitosan, whereas their oxygen permeability reduces by ~90%. This is ascribed to the chemical crosslinking between chitosan and GO nanoplatelets through borate ions, as well as the formation of a layered morphology with graphene nanoplatelets oriented parallel to the sample surface. The exceptional robust and high gas barrier film has promising application in the packaging industry. The borate-crosslinking chemistry represents the potential strategy for improving properties of other polymer nanocomposites.Chitosan (CS) is one of the most promising polymers due to its biocompatibility, biodegradability, and natural abundance. However, its poor mechanical and barrier properties make it difficult to satisfy a wide range of applications. Herein, borate ions, originating from the hydrolysis of sodium tetraborate decahydrate (borax), have been used to crosslink chitosan and graphene oxide (GO) nanocomposites. Chitosan films consisting of 1.0 wt% boron and 1.0 wt% GO exhibit a significant improvement in both the toughness and oxygen barrier properties compared to pristine chitosan. In particular the tensile strength of the samples after thermal treatment increases by ~160% compared to pristine chitosan, whereas their oxygen permeability reduces by ~90%. This is ascribed to the chemical

  2. Functional hydrophilic polystyrene beads with uniformly size and high cross-linking degree facilitated rapid separation of exenatide.

    Science.gov (United States)

    Li, Qiang; Zhao, Lan; Zhang, Rongyue; Huang, Yongdong; Zhang, Yan; Zhang, Kun; Wu, Xuexing; Zhang, Zhigang; Gong, Fangling; Su, Zhiguo; Ma, Guanghui

    2016-04-01

    A high cross-linking polystyrene(PSt)-based anion-exchange material with uniformly size, high ion exchange capacity, and high hydrophilicity was synthesized by a novel surface functionalization approach in this study. Uniformly sized PSt microspheres were prepared by the membrane emulsion polymerization strategy, and then modified by (1) conversing resid ual surface vinyl groups to epoxy groups followed by quaternization, and (2) decorating aromatic ring matrix including nitration, reduction and attachment of glycidyltrimethylammonium chloride. The 3-D morphology and porous features of microspheres were observed by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The surface of the modified PSt became roughness but the particle size remained same. Meanwhile, FT-IR spectra and laser scanning confocal microscope (LCSM) indicated that the modification groups had been successfully covalently coated onto the PSt microspheres. Modified PSt microspheres showed greatly improved hydrophilicity and biocompatibility with 0.387mmol/mL ion exchange capacity (IEC). In the application evaluation procedure, exenatide can be purified from 42.9% (peptide crudes) to 88.6% by modified PSt column with 97.1% recovery yield. This modified PSt microspheres had a large potential in application for efficient separation of peptides.

  3. Physical Characterization Of High Amylose/Pectin Mixtures Cross-Linked With Sodium Trimetaphosphate; Caracterizacao fisica de misturas alta amilose/pectina reticuladas com trimetafosfato de sodio

    Energy Technology Data Exchange (ETDEWEB)

    Carbinatto, F.M.; Cury, B.S.F.; Evangelista, R.C., E-mail: curybsf@fcfar.unesp.b [UNESP, Araraquara, SP (Brazil). Fac. de Ciencias Farmaceuticas

    2010-07-01

    Some researches have reported that pectin and high amylose mixtures presented superior mechanical properties in relation to those of the isolated polymers. In this work, mixtures at different ratios (1:4; 1:1) of pectin and high amylose were crosslinked with sodium trimetaphosphate at different degrees by varying reaction conditions. All samples were characterized by rheological and X-ray diffraction analyses. Samples without cross-linker were prepared as control. The oscillatory dynamic tests showed that all samples exhibited predominant elastic behavior, although cross-linked samples presented higher G' values, suggesting that crosslinking by phosphorylation resulted in more strength structures. The diffractograms showed that cross-linked samples underwent structural modifications that resulted in increase of crystallinity due to cross-linking process. (author)

  4. Novel myopic refractive correction with transepithelial very high-fluence collagen cross-linking applied in a customized pattern: early clinical results of a feasibility study

    Directory of Open Access Journals (Sweden)

    Kanellopoulos AJ

    2014-04-01

    Full Text Available Anastasios John Kanellopoulos LaserVision.gr Institute, Athens, Greece, and New York Medical School, New York, NY, USA Background: The purpose of this study is to report the safety and efficacy of a new application of collagen cross-linking using a novel device to achieve predictable refractive myopic changes in virgin corneas. Methods: Four cases were treated with a novel device employing very high-fluence collagen cross-linking applied in a myopic pattern. Prior to treatment, riboflavin solution was applied to the intact epithelium. The collagen cross-linking device was then engaged for a total of 12 J/cm2, to be applied transepithelially in a predetermined pattern. Cornea clarity, corneal keratometry, and corneal topography were evaluated by both Placido disc and Scheimpflug imaging, along with cornea anterior segment optical coherence tomography and endothelial cell counts. Results: An average of 2.3 diopters was achieved in the first week in all four cases treated with the very high-fluence myopic collagen cross-linking intervention. There was a slight regression to 1.44 diopters at 1 month, which remained stable at 6-month follow-up. The mean keratometry change was from 44.90 diopters to 43.46 diopters. There was no significant change in endothelial cell counts or corneal clarity. There was some mild change in epithelial thickness distribution, with the treated area showing a slight but homogeneous reduction in mean thickness from 52 µm to 44 µm. Conclusion: This report describes the novel application of very high-fluence collagen cross-linking with a predictable well defined myopic refractive (flattening corneal effect. This technique has the advantages of essentially no postoperative morbidity, immediate visual rehabilitation, and the potential for tapering until the desired result is achieved. Keywords: myopia, refractive correction, high-fluence collagen cross-linking, clinical results

  5. Wear resistance of the biocompatible phospholipid polymer-grafted highly cross-linked polyethylene liner against larger femoral head.

    Science.gov (United States)

    Moro, Toru; Takatori, Yoshio; Kyomoto, Masayuki; Ishihara, Kazuhiko; Kawaguchi, Hiroshi; Hashimoto, Masami; Tanaka, Takeyuki; Oshima, Hirofumi; Tanaka, Sakae

    2015-07-01

    The use of larger femoral heads to prevent the dislocation of artificial hip joints has recently become more common. However, concerns about the subsequent use of thinner polyethylene liners and their effects on wear rate have arisen. Previously, we prepared and evaluated the biological and mechanical effects of a novel highly cross-linked polyethylene (CLPE) liner with a nanometer-scaled graft layer of poly(2-methacryloyloxyethyl phosphorylcholine) (PMPC). Our findings showed that the PMPC-grafted particles were biologically inert and caused no subsequent bone resorptive responses and that the PMPC-grafting markedly decreased wear in a hip joint simulator. However, the metal or ceramic femoral heads used in this previous study had a diameter of 26 mm. Here, we investigated the wear-resistance of the PMPC-grafted CLPE liner with a 40-mm femoral head during 10 × 10(6) cycles of loading in the hip joint simulator. The results provide preliminary evidence that the grafting markedly decreased gravimetric wear rate and the volume of wear particles, even when coupled with larger femoral heads. Thus, we believe the PMPC-grafting will prolong artificial hip joint longevity both by preventing aseptic loosening and by improving the stability of articular surface.

  6. The Space Charge Effect on the Discharge Current in Cross-Linked Polyethylene under High AC Voltages

    Science.gov (United States)

    Kwon, Yoon-Hyeok; Hwangbo, Seung; Lee, June-Ho; Yi, Dong-Young; Han, Min-Koo

    2003-12-01

    The space charge distributions in solid dielectrics have been usually investigated by means of the pulsed electroacoustic (PEA) method. However, most previous studies have been limited to the phenomenological analysis under DC voltages. In our study, the space charge distribution in cross-linked polyethylene (XLPE) has been measured using AC voltages by means of the modified PEA method. Simultaneously, the streamer discharges in an air gap have been measured in order to investigate the relationship between space charge and discharge current, and the relationship has been adapted to the case of dielectric barrier discharge. At high AC voltages, discharge current increases to the critical point, but no further increase is exhibited over the critical voltage and the discharge pattern is resolved by the space charge. This result indicates that the frequency effect and space charge characteristics of dielectric materials are preferred to the voltage effect in the adaptation to dielectric barrier discharge. The results well explain the space charge effect on partial discharge and the dielectric barrier discharge phenomenon.

  7. Highly cross-linked polyethylene acetabular liners retrieved four to five years after revision surgery: a report of two cases.

    Science.gov (United States)

    Teeter, Matthew G; Naudie, Douglas D R; Charron, Kory D; Holdsworth, David W

    2010-08-01

    There is currently considerable interest in the use of highly cross-linked polyethylene (XLPE) acetabular liners for total hip arthroplasty (THA). In literature, only a single retrieval analysis of one type of XLPE liner implanted for greater than four years exists. The purpose of the present report is to quantify surface deviations in two XLPE liners implanted during revision THA and retrieved between four to five years after implantation. The two XLPE acetabular liners (Reflection, Smith and Nephew Inc., Memphis, TN) were retrieved from patients undergoing their second revision surgery, at 4.90 and 4.07 years. The retrieved liners and a new, non-implanted, unworn liner of the same size were scanned using micro-computed tomography (micro-CT). Articular surface deviation maps were created by comparing the retrievals to the unworn liner, based on the liner geometry obtained from micro-CT. The linear penetration rates were found to be 0.018 and 0.008 mm/year. Localized scratches and pits with deviations greater than 0.205 mm were also found on the articular surfaces of both liners. The XLPE liners retrieved from the two cases demonstrated low linear penetration rates. Regions with greater focal deviations were also apparent, likely due to third-body wear. The results are consistent with previously published clinical follow-ups of other XLPE liners.

  8. Rotational echo double resonance detection of cross-links formed in mussel byssus under high-flow stress.

    Science.gov (United States)

    McDowell, L M; Burzio, L A; Waite, J H; Schaefer, J

    1999-07-16

    13C2H rotational echo double resonance NMR has been used to provide the first evidence for the formation of quinone-derived cross-links in mussel byssal plaques. Labeling of byssus was achieved by allowing mussels to filter feed from seawater containing L-[phenol-4-13C]tyrosine and L-[ring-d4]tyrosine for 2 days. Plaques and threads were harvested from two groups of mussels over a period of 28 days. One group was maintained in stationary water while the other was exposed to turbulent flow at 20 cm/s. The flow-stressed byssal plaques exhibited significantly enhanced levels of 5, 5'-di-dihydroxyphenylalanine cross-links. The average concentration of di-dihydroxyphenylalanine cross-links in byssal plaques is 1 per 1800 total protein amino acid residues.

  9. Highly stable CO2/N2 and CO2/CH4 selectivity in hyper-cross-linked heterocyclic porous polymers.

    Science.gov (United States)

    Saleh, Muhammad; Lee, Han Myoung; Kemp, K Christian; Kim, Kwang S

    2014-05-28

    The largest obstacles for landfill/flue gas separation using microporous materials are small adsorption values and low selectivity ratios. This study demonstrates that these adsorption and selectivity challenges can be overcome by utilizing a series of hyper-cross-linked heterocyclic polymer networks. These microporous organic polymers (MOPs) were synthesized in a single step by inexpensive Friedel-Crafts-catalyzed reactions using dimethoxymethane as an external linker. The amorphous networks show moderate Brunauer-Emmett-Teller surface areas up to 1022 m(2) g(-1), a narrow pore size distribution in the range from 6 to 8 Å, and high physicochemical stability. Owing to the presence of the heteroatomic pore surfaces in the networks, they exhibit maximum storage capacities for CO2 of 11.4 wt % at 273 K and 1 atm. Additionally, remarkable selectivity ratios for CO2 adsorption over N2 (100) and CH4 (15) at 273 K were obtained. More importantly, as compared with any other porous materials, much higher selectivity for CO2/N2 (80) and CO2/CH4 (15) was observed at 298 K, showing that these selectivity ratios remain high at elevated temperature. The very high CO2/N2 selectivity values are ascribed to the binding affinity of abundantly available electron-rich basic heteroatoms, high CO2 isoteric heats of adsorption (49-38 kJ mol(-1)), and the predominantly microporous nature of the MOPs. Binding energies calculated using the high level of ab initio theory showed that the selectivity is indeed attributed to the heteroatom-CO2 interactions. By employing an easy and economical synthesis procedure these MOPs with high thermochemical stability are believed to be a promising candidate for selective CO2 capture.

  10. Five-Year Experience of Vitamin E-Diffused Highly Cross-Linked Polyethylene Wear in Total Hip Arthroplasty Assessed by Radiostereometric Analysis

    DEFF Research Database (Denmark)

    Nebergall, Audrey K; Troelsen, Anders; Rubash, Harry E;

    2016-01-01

    BACKGROUND: Vitamin E-diffused highly cross-linked polyethylene (VEPE) was developed to reduce oxidation without compromising mechanical strength. The purpose of this study was to evaluate VEPE in vivo using radiostereometric analysis (RSA) and patient-reported outcome measures (PROMs). METHODS: ...

  11. Wear resistant performance of highly cross-linked and annealed ultra-high molecular weight polyethylene against ceramic heads in total hip arthroplasty.

    Science.gov (United States)

    Sato, Taishi; Nakashima, Yasuharu; Akiyama, Mio; Yamamoto, Takuaki; Mawatari, Taro; Itokawa, Takashi; Ohishi, Masanobu; Motomura, Goro; Hirata, Masanobu; Iwamoto, Yukihide

    2012-12-01

    The purpose of this study was to examine the effects of ceramic femoral head material, size, and implantation periods on the wear of annealed, cross-linked ultra-high molecular weight polyethylene (UHMWPE) (XLPE) in total hip arthroplasty compared to non-cross-linked conventional UHMWPE (CPE). XLPE was fabricated by cross-linking with 60 kGy irradiation and annealing. Femoral heads made from zirconia and alumina ceramics and cobalt-chrome (CoCr) of 22 or 26 mm diameter were used. In this retrospective cohort study, the femoral head penetration into the cup was measured digitally on radiographs of 367 hips with XLPE and 64 hips with CPE. The average follow-up periods were 6.3 and 11.9 years, respectively. Both XLPE creep and wear rates were significantly lower than those of CPE (0.19 mm vs. 0.44 mm, 0.0001 mm/year vs. 0.09 mm/year, respectively). Zirconia displayed increased wear rates compared to alumina in CPE; however, there was no difference among head materials in XLPE (0.0008, 0.00007, and -0.009 mm/year for zirconia, alumina, and CoCr, respectively). Neither head size or implantation period impacted XLPE wear. In contrast to CPE, XLPE displayed low wear rates surpassing the effects of varying femoral head material, size, implantation period, and patient demographics. Further follow-up is required to determine the long-term clinical performance of the annealed XLPE.

  12. Wear and migration of highly cross-linked and conventional cemented polyethylene cups with cobalt chrome or Oxinium femoral heads: a randomized radiostereometric study of 150 patients.

    Science.gov (United States)

    Kadar, Thomas; Hallan, Geir; Aamodt, Arild; Indrekvam, Kari; Badawy, Mona; Skredderstuen, Arne; Havelin, Leif Ivar; Stokke, Terje; Haugan, Kristin; Espehaug, Birgitte; Furnes, Ove

    2011-08-01

    This randomized study was performed to compare wear and migration of five different cemented total hip joint articulations in 150 patients. The patients received either a Charnley femoral stem with a 22.2 mm head or a Spectron EF femoral stem with a 28 mm head. The Charnley articulated with a γ-sterilized Charnley Ogee acetabular cup. The Spectron EF was used with either EtO-sterilized non-cross-linked polyethylene (Reflection All-Poly) or highly cross-linked (Reflection All-Poly XLPE) cups, combined with either cobalt chrome (CoCr) or Oxinium femoral heads. The patients were followed with repeated RSA measurements for 2 years. After 2 years, the EtO-sterilized non-cross-linked Reflection All-Poly cups had more than four times higher proximal penetration than its highly cross-linked counterpart. Use of Oxinium femoral heads did not affect penetration at 2 years compared to heads made of CoCr. Further follow-up is needed to evaluate the benefits, if any, of Oxinium femoral heads in the clinical setting. The Charnley Ogee was not outperformed by the more recently introduced implants in our study. We conclude that this prostheses still represents a standard against which new implants can be measured.

  13. In situ thermally cross-linked polyacrylonitrile as binder for high-performance silicon as lithium ion battery anode.

    Science.gov (United States)

    Shen, Lanyao; Shen, Lian; Wang, Zhaoxiang; Chen, Liquan

    2014-07-01

    Electrode integrity and electric contact between particles and between particle and current collector are critical for electrochemical performance, especially for that of electrode materials with large volume change during cycling and with poor electric conductivity. We report on the in situ thermally cross-linked polyacrylonitrile (PAN) as a binder for silicon-based anodes of lithium-ion batteries. The electrode delivers excellent cycle life and rate capability with a reversible capacity of about 1450 mA h g(-1) even after 100 cycles. The improved electrochemical performance of such silicon electrodes is attributed to heat-treatment-induced cross-linking and the formation of conjugated PAN. These findings open new avenues to explore other polymers for both anode and cathode electrodes of rechargeable batteries.

  14. Preparation and Characterization of Epoxy Resin Cross-Linked with High Wood Pyrolysis Bio-Oil Substitution by Acetone Pretreatment

    Directory of Open Access Journals (Sweden)

    Yi Liu

    2017-03-01

    Full Text Available The use of cost effective solvents may be necessary to store wood pyrolysis bio-oil in order to stabilize and control its viscosity, but this part of the production system has not been explored. Conversely, any rise in viscosity during storage, that would occur without a solvent, will add variance to the production system and render it cost ineffective. The purpose of this study was to modify bio-oil with a common solvent and then react the bio-oil with an epoxy for bonding of wood without any loss in properties. The acetone pretreatment of the bio-oil/epoxy mixture was found to improve the cross-linking potential and substitution rate based on its mechanical, chemical, and thermal properties. Specifically, the bio-oil was blended with epoxy resin at weight ratios ranging from 2:1 to 1:5 and were then cured. A higher bio-oil substitution rate was found to lower the shear bond strength of the bio-oil/epoxy resins. However, when an acetone pretreatment was used, it was possible to replace the bio-oil by as much as 50% while satisfying usage requirements. Extraction of the bio-oil/epoxy mixture with four different solvents demonstrated an improvement in cross-linking after acetone pretreatment. ATR-FTIR analysis confirmed that the polymer achieved a higher cross-linked structure. DSC and TGA curves showed improved thermal stability with the addition of the acetone pretreatment. UV-Vis characterization showed that some functional groups of the bio-oil to epoxy system were unreacted. Finally, when the resin mixture was utilized to bond wood, the acetone pretreatment coupled with precise tuning of the bio-oil:epoxy ratio was an effective method to control cross-linking while ensuring acceptable bond strength.

  15. Highly Cross-Linked Versus Conventional Polyethylene in Posterior-Stabilized Total Knee Arthroplasty at a Mean 5-Year Follow-up.

    Science.gov (United States)

    Meneghini, R Michael; Lovro, Luke R; Smits, Shelly A; Ireland, Philip H

    2015-10-01

    Concerns of highly cross-linked polyethylene (XLPE) in total knee arthroplasty (TKA) exist regarding fatigue resistance and oxidation, particularly in posterior-stabilized (PS) designs. A prospective cohort study of 114 consecutive PS TKAs utilized conventional polyethylene in 50 knees and second-generation annealed XLPE in 64 TKAs. Clinical (Short-Form 36, Knee Society Scores, and LEAS) and radiographic outcomes were evaluated at a mean of 5 years in 103 TKAs. Mean KSS scores were 12 points higher (P=0.01) and SF-36 physical function subset 14 points higher (P=0.005) in the XLPE group. There was no radiographic osteolysis or mechanical failure related to the tibial polyethylene in either group. At 5-year follow-up, no deleterious effects related to highly cross-linked posterior stabilized tibial polyethylene inserts were observed.

  16. Long-term safety and efficacy follow-up of prophylactic higher fluence collagen cross-linking in high myopic laser-assisted in situ keratomileusis

    Directory of Open Access Journals (Sweden)

    Kanellopoulos AJ

    2012-07-01

    Full Text Available Anastasios John KanellopoulosLaservision.gr Institute, Athens, Greece, and New York University Medical School, New York, NY, USABackground: The purpose of this study was to evaluate the safety and efficacy of ultraviolet A irradiation cross-linking on completion for cases of high myopic laser-assisted in situ keratomileusis (LASIK.Methods: Forty-three consecutive LASIK cases treated with femtosecond laser flap and the WaveLight excimer platform were evaluated perioperatively for uncorrected visual acuity, best corrected spectacle visual acuity, refraction, keratometry, topography, total and flap pachymetry, corneal optical coherence tomography, and endothelial cell count. All eyes at the completion of LASIK had cross-linking through the repositioned flap, with higher fluence (10 mW/cm2 ultraviolet light of an average 370 µm wavelength and 10 mW/cm2 fluence applied for 3 minutes following an earlier single instillation of 0.1% riboflavin within the flap interface. Mean follow-up duration was 3.5 (range 1.0–4.5 years.Results: Mean uncorrected visual acuity changed from 0.2 to 1.2, best corrected spectacle visual acuity from 1.1 to 1.2, spherical equivalent from -7.5 diopters (D to -0.2 D, keratometry from 44.5 D to 38 D, flap pachymetry from 105 µm to, total pachymetry from 525 to 405, and endothelial cell count from 2750 to 2800. None of the cases developed signs of ectasia or significant regression during follow-up.Conclusion: Prophylactic collagen cross-linking for high-risk LASIK cases appears to be a safe and effective adjunctive treatment for refractive regression and potential ectasia. This application may be viewed as prophylactic customization of the biomechanical behavior of corneal collagen.Keywords: prophylactic collagen cross-linking, laser-assisted in situ keratomileusis, high-risk, post-LASIK ectasia

  17. Optimisation of the reaction conditions for the production of cross-linked starch with high resistant starch content.

    Science.gov (United States)

    Kahraman, Kevser; Koksel, Hamit; Ng, Perry K W

    2015-05-01

    The optimum reaction conditions (temperature and pH) for the preparation of cross-linked (CL) corn and wheat starches with maximum resistant starch (RS) content were investigated by using response surface methodology (RSM). According to the preliminary results, five levels were selected for reaction temperature (38-70 °C) and pH (10-12) in the main study. RS contents of the CL corn and wheat starch samples increased with increasing temperature and pH, and pH had a greater influence on RS content than had temperature. The maximum RS content (with a maximum p value of 0.4%) was obtained in wheat starch cross-linked at 38 °C and pH 12. In the case of CL corn starch, the optimum condition was 70 °C and pH 12. CL corn and wheat starch samples were also produced separately under the optimum conditions and their RS contents were 80.4% and 83.9%, respectively. These results were also in agreement with the values predicted by RSM.

  18. Boron cross-linked graphene oxide/polyvinyl alcohol nanocomposite gel electrolyte for flexible solid-state electric double layer capacitor with high performance

    KAUST Repository

    Huang, Yi-Fu

    2014-06-01

    A new family of boron cross-linked graphene oxide/polyvinyl alcohol (GO-B-PVA) nanocomposite gels is prepared by freeze-thaw/boron cross-linking method. Then the gel electrolytes saturated with KOH solution are assembled into electric double layer capacitors (EDLCs). Structure, thermal and mechanical properties of GO-B-PVA are explored. The electrochemical properties of EDLCs using GO-B-PVA/KOH are investigated, and compared with those using GO-PVA/KOH gel or KOH solution electrolyte. FTIR shows that boron cross-links are introduced into GO-PVA, while the boronic structure inserted into agglomerated GO sheets is demonstrated by DMA analysis. The synergy effect of the GO and the boron crosslinking benefits for ionic conductivity due to unblocking ion channels, and for improvement of thermal stability and mechanical properties of the electrolytes. Higher specific capacitance and better cycle stability of EDLCs are obtained by using the GO-B-PVA/KOH electrolyte, especially the one at higher GO content. The nanocomposite gel electrolytes with excellent electrochemical properties and solid-like character are candidates for the industrial application in high-performance flexible solid-state EDLCs. © 2014 Elsevier Ltd.

  19. IN SITU PREPARED TiO2 NANOPARTICLES CROSS-LINKED SULFONATED PVA MEMBRANES WITH HIGH PROTON CONDUCTIVITY FOR DMFC

    Directory of Open Access Journals (Sweden)

    Jignasa N. Solanki

    2016-07-01

    Full Text Available Organic/inorganic membranes based on sulfonated poly(vinyl alcohol (SPVA and in situ prepared TiO2 nanoparticles nanocomposite membranes with various compositions were prepared to use as proton exchange membranes in direct membrane fuel cells. Poly(vinyl alcohol (PVA was sulfonated and cross-linked separately by 4-formylbenzene-1,3-disulfonic acid disodium salt hydrate and glutaraldehyde. The ion exchange capacity and proton conductivity of the membranes increased with increasing amount of TiO2 nanoparticles. The composite membranes with 15 wt% TiO2 exhibited excellent proton conductivity of 0.0822 S cm-1, as well as remarkably low methanol permeability of 1.11×10-9 cm2 s-1. The thermal stability and durability were also superior and performance in methanol fuel cell was also reasonably good

  20. Vitamin-E blended and infused highly cross-linked polyethylene for total hip arthroplasty: a comparison of three-dimensional crystalline morphology and strain recovery behavior.

    Science.gov (United States)

    Takahashi, Yasuhito; Masaoka, Toshinori; Yamamoto, Kengo; Shishido, Takaaki; Tateiwa, Toshiyuki; Kubo, Kosuke; Pezzotti, Giuseppe

    2014-08-01

    Vitamin-E (α-tocopherol) is now recognized worldwide as one of the most promising antioxidant agents for highly cross-linked polyethylene (HXLPE) used in total joint replacements. In the contemporary manufacturing processes, two alternative methods are currently accepted to incorporate this antioxidant into polyethylene microstructure: (i) blending vitamin-E before consolidation and radiation crosslinking; (ii) infusing vitamin-E via a homogenizing heat treatment after radiation crosslinking. However, the effects of these technological differences on crystalline morphology and mechanical behavior of polyethylene remains to be fully elucidated. The aim of this paper is to quantitatively evaluate the microstructural differences of commercially available vitamin-E blended and infused HXLPE liner (referred to as Liner BL and IF, respectively). For this purpose, confocal/polarized Raman spectroscopy was used to systematically examine the three-phase percentages (amorphous (αa), crystalline (αc), and intermediate third phase (αt)), preferential molecular orientation (θp), and degree of crystalline anisotropy (〈P2(cosβ)〉). Additionally, we compared the time-dependent deformation of Liner BL and IF as obtained by uniaxial stress relaxation tests followed by strain recovery. Distinctive features of the near-surface αc, θp, and〈P2(cosβ)〉 were clearly observed within the first 35μm in the two studied liners. Despite the equivalent level of the bulk αc and 〈P2(cosβ)〉, higher restoring force against a uniaxial strain was observed in Liner IF, which reflects a higher crosslink density in its amorphous phase. On the other hands, a higher degree of surface orientational randomness was detected in Liner BL, which is structurally more beneficial for minimizing the in-vivo occurrence of strain-softening-assisted wear.

  1. Wear performance of neat and vitamin E blended highly cross-linked PE under severe conditions: The combined effect of accelerated ageing and third body particles during wear test.

    Science.gov (United States)

    Affatato, Saverio; De Mattia, Jonathan Salvatore; Bracco, Pierangiola; Pavoni, Eleonora; Taddei, Paola

    2016-12-01

    The objective of this study is to evaluate the effects of third-body particles on the in vitro wear behaviour of three different sets of polyethylene acetabular cups after prolonged testing in a hip simulator and accelerated ageing. Vitamin E-blended, cross-linked polyethylene (XLPE_VE), cross-linked polyethylene (XLPE) and conventional polyethylene (STD_PE) acetabular cups were simulator tested for two million cycles under severe conditions (i.e. by adding third-body particles to the bovine calf serum lubricant). Micro-Fourier Transform Infrared and micro-Raman spectroscopic analyses, differential scanning calorimetry, and crosslink density measurements were used to characterize the samples at a molecular level. The STD_PE cups had twice mass loss than the XLPE_VE components and four times than the XLPE samples; statistically significant differences were found between the mass losses of the three sets of cups. The observed wear trend was justified on the basis of the differences in cross-link density among the samples (XLPE>XLPE_VE>STD_PE). FTIR crystallinity profiles, bulk DSC crystallinity and surface micro-Raman crystallinity seemed to have a similar behaviour upon testing: all of them (as well as the all-trans and ortho-trans contents) revealed the most significant changes in XLPE and XLPE_VE samples. The more severe third-body wear testing conditions determined more noticeable changes in all spectroscopic markers with respect to previous tests. Unexpectedly, traces of bulk oxidation were found in both STD_PE (unirradiated) and XLPE (remelting-stabilized), which were expected to be stable to oxidation; on the contrary, XLPE_VE demonstrated a high oxidative stability in the present, highly demanding conditions.

  2. Thirteen-Year Evaluation of Highly Cross-Linked Polyethylene Articulating With Either 28-mm or 36-mm Femoral Heads Using Radiostereometric Analysis and Computerized Tomography

    DEFF Research Database (Denmark)

    Nebergall, Audrey K; Greene, Meridith E; Rubash, Harry

    2016-01-01

    radiograph, and CT follow-up. The 1-year and 13-year plain radiographs as well as the CT scans were analyzed for the presence of osteolysis. RESULTS: The 13-year mean ± standard error steady-state wear was 0.05 ± 0.02 mm with no significant increase over time or between the 2 head size groups. Two patients......BACKGROUND: The objective of this 13-year prospective evaluation of highly cross-linked ultra high molecular weight polyethylene (HXLPE) was to (1) assess the long-term wear of HXLPE articulating with 2 femoral head sizes using radiostereometric analysis (RSA) and to (2) determine if osteolysis...

  3. A comparison of the wear and physical properties of silane cross-linked polyethylene and ultra-high molecular weight polyethylene.

    Science.gov (United States)

    Sakoda, H; Voice, A M; McEwen, H M; Isaac, G H; Hardaker, C; Wroblewski, B M; Fisher, J

    2001-12-01

    Cross-linked polyethylenes are being introduced widely in acetabular cups in hip prostheses as a strategy to reduce the incidence of wear debris-induced osteolysis. It will be many years before substantial clinical data can be collected on the wear of these new materials. Silane cross-linked polyethylene (XLPE) was introduced into clinical practice in a limited series of acetabular cups in 1986 articulating against 22.225-mm alumina ceramic femoral heads and showed reduced wear rates compared with conventionally sterilized (gamma irradiation in air) ultra-high molecular weight polyethylene (UHMWPE). We compared the wear of XLPE manufactured in 1986 with the wear of UHMWPE manufactured in 1986 in nonirradiated and irradiated forms. In the nonirradiated forms, the wear of XLPE was 3 times less than UHWMPE when articulating against smooth counterfaces. The nonirradiated materials did not show signs of oxidation. In the irradiated forms, only UHMWPE showed high levels of oxidation, and this caused a substantial increase in wear. Antioxidants added to XLPE during processing gave resistance to oxidative degradation. When sliding against scratched counterfaces, the wear of UHMWPE increased by a factor of 2 to 3 times. Against the same scratched counterfaces, the wear of XLPE increased dramatically by 30 to 200 times. This difference may be attributed to the reduction in toughness of XLPE. Clinically, XLPE has been articulated against damage-resistant ceramic heads, and this probably has been an important factor in contributing to reduced wear. New cross-linked polyethylenes differ considerably from XLPE. This study indicates that it is prudent to examine the wear of new polyethylenes under a range of conditions that may occur in vivo.

  4. Simulation of Fracture Nucleation in Cross-Linked Polymer Networks

    Science.gov (United States)

    Moller, J. C.; Barr, S. A.; Schultz, E. J.; Breitzman, T. D.; Berry, R. J.

    2013-02-01

    A novel atomistic simulation method is developed whereby polymer systems can undergo strain-rate-controlled deformation while bond scission is enabled. The aim is to provide insight into the nanoscale origins of fracture. Various highly cross-linked epoxy systems including various resin chain lengths and levels of nonreactive dilution were examined. Consistent with the results of physical experiments, cured resin strength increased and ductility decreased with increasing cross-link density. An analysis of dihedral angle activity shows the locations in the molecular network that are most absorptive of mechanical energy. Bond scission occurred principally at cross-link sites as well as between phenyl rings in the bisphenol moiety. Scissions typically occurred well after yield and were accompanied by steady increases in void size and dihedral angle motion between bisphenol moieties and at cross-link sites. The methods developed here could be more broadly applied to explore and compare the atomistic nature of deformation for various polymers such that mechanical and fracture properties could be tuned in a rational way. This method and its results could become part of a solution system that spans multiple length and time scales and that could more completely represent such mechanical events as fracture.

  5. Highly Flexible and Self-Healable Thermal Interface Material Based on Boron Nitride Nanosheets and a Dual Cross-Linked Hydrogel.

    Science.gov (United States)

    Jiang, Hongbo; Wang, Zifeng; Geng, Huiyuan; Song, Xiufeng; Zeng, Haibo; Zhi, Chunyi

    2017-03-22

    The booming growth of flexible and stretchable electronic devices with increasing power and multifunctionalities calls for novel highly efficient thermal interface materials (TIMs) with versatile functions, such as high deformability and self-healing ability, whereas traditional metallic-based or grease-based ones could hardly provide. Herein, we report a highly flexible and self-healable dual-cross-linked hydrogel-based nanocomposite filled with hexagonal boron nitride (h-BN) nanosheets fabricated by in situ polymerization of acrylic acid (AA). The thermal conductivity of the composites can be tuned by adjusting both fraction of BNNSs and water content. Although a solid, the highly flexible characteristic of the developed TIMs enables a perfect ability to replicate the texture of a rough surface, which may greatly enhance thermal transfer between adjacent surfaces. By increasing the water content to soften the material, it can be recycled and reused for different kinds of rough surface. In addition, benefiting from the dual-cross-linked structure, the composites are capable of recovering both mechanical strength and thermal conductivity even from severe structural breakdowns, for example, three consecutive cutting and healing cycles. This study may pave the way to fabrication of multifunctional highly flexible TIMs, which may promote the development of heat dissipation materials.

  6. Catalytic trimerization of aromatic nitriles and triaryl-s-triazine ring cross-linked high temperature resistant polymers and copolymers made thereby

    Science.gov (United States)

    Hsu, L. C. (Inventor)

    1979-01-01

    Triazine compounds and cross-linked polymer compositions are made by heating aromatic nitriles to a temperature in the range of from about 100 C to about 700 C, and preferably in the range of from about 200 C to about 350 C, in the presence of a catalyst or mixture of catalysts selected from one or more of the following groups: (1) organic sulfonic and sulfinic acids, (2) organic phosphonic and phosphinic acids, and (3)metallic acetylacetonates, at a pressure in the range of from about atmospheric pressure to about 10,000 psi and preferably in the range of from about 200 psi to about 750 psi. Aromatic nitrile-modified (terminated and/or appended) imide, benzimidazole, imidazopyrrolone, quinoxaline, and other condensation type prepolymers or their precopolymers are made which are trimerized with or without a filler by the aforementioned catalytic trimerization process into triaryl-s-triazine ring containing or cross-linked polymeric or copolymeric products useful in applications requiring high thermal-oxidative stability and high performance structural properties at elevated temperatures.

  7. Initiated Chemical Vapor Deposition (iCVD) of Highly Cross-Linked Polymer Films for Advanced Lithium-Ion Battery Separators.

    Science.gov (United States)

    Yoo, Youngmin; Kim, Byung Gon; Pak, Kwanyong; Han, Sung Jae; Song, Heon-Sik; Choi, Jang Wook; Im, Sung Gap

    2015-08-26

    We report an initiated chemical vapor deposition (iCVD) process to coat polyethylene (PE) separators in Li-ion batteries with a highly cross-linked, mechanically strong polymer, namely, polyhexavinyldisiloxane (pHVDS). The highly cross-linked but ultrathin pHVDS films can only be obtained by a vapor-phase process, because the pHVDS is insoluble in most solvents and thus infeasible with conventional solution-based methods. Moreover, even after the pHVDS coating, the initial porous structure of the separator is well preserved owing to the conformal vapor-phase deposition. The coating thickness is delicately controlled by deposition time to the level that the pore size decreases to below 7% compared to the original dimension. The pHVDS-coated PE shows substantially improved thermal stability and electrolyte wettability. After incubation at 140 °C for 30 min, the pHVDS-coated PE causes only a 12% areal shrinkage (versus 90% of the pristine separator). The superior wettability results in increased electrolyte uptake and ionic conductivity, leading to significantly improved rate performance. The current approach is applicable to a wide range of porous polymeric separators that suffer from thermal shrinkage and poor electrolyte wetting.

  8. Three-dimensional cross-linked Polyaniline fiber/N-doped porous carbon with enhanced electrochemical performance for high-performance supercapacitor

    Science.gov (United States)

    Guo, ShuaiNan; Shen, HaoKai; Tie, ZhongFu; Zhu, Sheng; Shi, PengHui; Fan, JinChen; Xu, QunJie; Min, YuLin

    2017-08-01

    In this work, we design a novel and facile strategy to synthesize a three-dimensional (3D) cross-linked structural composite with PANI and MOF-derived N-doped porous carbon composite (3CPC). The novel and facile method realize interconnected structure composed of an ultrahigh surface area of N-doped porous carbon and conductive PANI fiber, which can offer more contact area between the electrode material and electrolyte to provide more active sites for charge storage and shorten the pathway for electron transfer. As a result, the 3CPC shows an extraordinarily efficient specific capacity of 755 F g-1 and good cycling stability at a current density of 1 A g-1 in 1 M H2SO4, which suggests its potential application as an efficient material for supercapacitor.

  9. Synthesis and properties of reprocessable sulfonated polyimides cross-linked via acid stimulation for use as proton exchange membranes

    Science.gov (United States)

    Zhang, Boping; Ni, Jiangpeng; Xiang, Xiongzhi; Wang, Lei; Chen, Yongming

    2017-01-01

    Cross-linked sulfonated polyimides are one of the most promising materials for proton exchange membrane (PEM) applications. However, these cross-linked membranes are difficult to reprocess because they are insoluble. In this study, a series of cross-linkable sulfonated polyimides with flexible pendant alkyl side chains containing trimethoxysilyl groups is successfully synthesized. The cross-linkable polymers are highly soluble in common solvents and can be used to prepare tough and smooth films. Before the cross-linking reaction is complete, the membranes can be reprocessed, and the recovery rate of the prepared films falls within an acceptable range. The cross-linked membranes are obtained rapidly when the cross-linkable membranes are immersed in an acid solution, yielding a cross-linking density of the gel fraction of greater than 90%. The cross-linked membranes exhibit high proton conductivities and tensile strengths under hydrous conditions. Compared with those of pristine membranes, the oxidative and hydrolytic stabilities of the cross-linked membranes are significantly higher. The CSPI-70 membrane shows considerable power density in a direct methanol fuel cell (DMFC) test. All of these results suggest that the prepared cross-linked membranes have great potential for applications in proton exchange membrane fuel cells.

  10. Fluorinated and Thermo-Cross-Linked Polyhedral Oligomeric Silsesquioxanes: New Organic-Inorganic Hybrid Materials for High-Performance Dielectric Application.

    Science.gov (United States)

    Wang, Jiajia; Sun, Jing; Zhou, Junfeng; Jin, Kaikai; Fang, Qiang

    2017-04-12

    A fluorinated and thermo-cross-linked polyhedral oligomeric silsesquioxane (POSS) has been successfully synthesized by thermal polymerization of a fluorinated POSS monomer having an inorganic silsesquioxane core and organic side chains bearing thermo-cross-linkable trifluorovinyl ether groups. This new inorganic-organic hybrid polymer shows high thermostability with a 5 wt % loss temperature of 436 °C, as well as good transparency (a sheet with an average thickness of 1.5 mm shows high transmittance of 92% varying from 400 to 1100 nm). Moreover, the polymer exhibits both low dielectric constant (polymer also shows low water uptake (polymer is very suitable to be utilized as a high-performance dielectric material for fabrication of high-frequency printed circuit boards or encapsulation resins for integrated circuit dies in the microelectronic industry. Furthermore, this work also provides a route for the preparation of fluorinated POSS-based polymers.

  11. Design and Synthesis of Cross-Linked Copolymer Membranes Based on Poly(benzoxazine and Polybenzimidazole and Their Application to an Electrolyte Membrane for a High-Temperature PEM Fuel Cell

    Directory of Open Access Journals (Sweden)

    Hyuk Chang

    2013-01-01

    Full Text Available Elevated-temperature (100~200 °C polymer electrolyte membrane (PEM fuel cells have many features, such as their high efficiency and simple system design, that make them ideal for residential micro-combined heat and power systems and as a power source for fuel cell electric vehicles. A proton-conducting solid-electrolyte membrane having high conductivity and durability at elevated temperatures is essential, and phosphoric-acid-containing polymeric material synthesized from cross-linked polybenzoxazine has demonstrated feasible characteristics. This paper reviews the design rules, synthesis schemes, and characteristics of this unique polymeric material. Additionally, a membrane electrode assembly (MEA utilizing this polymer membrane is evaluated in terms of its power density and lifecycle by an in situ accelerated lifetime test. This paper also covers an in-depth discussion ranging from the polymer material design to the cell performance in consideration of commercialization requirements.

  12. 交联密度法研究硅烷偶联剂对室温硫化硅橡胶性能的影响%A cross-linking density method study of the effect of a silane coupling agent on the performance of room temperature vulcanized (RTV) silicone rubber

    Institute of Scientific and Technical Information of China (English)

    苏清福; 杨宇; 李刚; 杨小平

    2013-01-01

    The cross-linking density method was used to investigate the effects of a coupling agent on the mechanical properties and the high and low temperature performance of silica-enhanced hydroxyl-terminated phenylsiloxane rubber. Mechanical properties, SEM, cross-linking density, DSC, DMA, and TGA analysis all showed that the chemical cross-linking density ratio was the greatest when the mass fraction of γ-aminopropyltriethoxysilane ( KH550) was 6 parts per hundreds of hydroxyl-terminated phenylsiloxane rubber, which resulted in room temperature vulcanized silicone rubber with the highest tensile properties, as well as the optimum interface adhesion between silica and the silicone rubber. Meanwhile, the lower glass transition temperature, which resulted from the decrease in the physical cross-linking density ratio, indicated the improvement of the low temperature resistance of the silicone rubber. The increase in the chemical cross-linking density ratio showed that the heat resistance of RTV silicone rubber was improved.%采用交联密度法探讨了硅烷偶联剂对SiO2增强端羟基苯基硅橡胶的作用机理及高低温性能的影响.对室温硫化硅橡胶的力学性能、交联密度、热性能等进行了测试,测试结果表明:当γ-氨丙基三乙氧基硅烷(KH550)用量为6份时,室温硫化硅橡胶的化学交联密度比例最大,力学性能最优,SiO2与硅橡胶的界面性能最好;硅橡胶交联体系中物理交联比例的减小导致玻璃化转变温度降低,硅橡胶的耐低温性能改善;化学交联密度比例增加,硅橡胶的耐热性提高.

  13. Computational exploration of polymer nanocomposite mechanical property modification via cross-linking topology

    Energy Technology Data Exchange (ETDEWEB)

    Lacevic, N; Gee, R; Saab, A; Maxwell, R

    2008-04-24

    Molecular dynamics simulations have been performed in order to study the effects of nanoscale filler cross-linking topologies and loading levels on the mechanical properties of a model elastomeric nanocomposite. The model system considered here is constructed from octa-functional polyhedral oligomeric silsesquioxane (POSS) dispersed in a poly(dimethylsiloxane) (PDMS) matrix. Shear moduli, G, have been computed for pure and for filled and unfilled PDMS as a function of cross-linking density, POSS fill loading level, and polymer network topology. The results reported here show that G increases as the cross-linking (covalent bonds formed between the POSS and the PDMS network) density increases. Further, G is found to have a strong dependence on cross-linking topology. The increase in shear modulus, G, for POSS filled PDMS is significantly higher than that for unfilled PDMS cross-linked with standard molecular species, suggesting an enhanced reinforcement mechanism for POSS. In contrast, in blended systems (POSS/PDMS mixture with no cross-linking) G was not observed to significantly increase with POSS loading. Finally, we find intriguing differences in the structural arrangement of bond strains between the cross-linked and the blended systems. In the unfilled PDMS the distribution of highly strained bonds appears to be random, while in the POSS filled system, the strained bonds form a net-like distribution that spans the network. Such a distribution may form a structural network 'holding' the composite together and resulting in increases in G compared to an unfilled, cross-linked system. These results are of importance for engineering of new POSS-based multifunctional materials with tailor-made mechanical properties.

  14. Computational exploration of polymer nanocomposite mechanical property modification via cross-linking topology.

    Science.gov (United States)

    Lacevic, Naida; Gee, Richard H; Saab, Andrew; Maxwell, Robert

    2008-09-28

    Molecular dynamics simulations have been performed in order to study the effects of nanoscale filler cross-linking topologies and loading levels on the mechanical properties of a model elastomeric nanocomposite. The model system considered here is constructed from octafunctional polyhedral oligomeric silsesquioxane (POSS) dispersed in a poly(dimethylsiloxane) (PDMS) matrix. Shear moduli, G, have been computed for pure and for filled and unfilled PDMS as a function of cross-linking density, POSS fill loading level, and polymer network topology. The results reported here show that G increases as the cross-linking (covalent bonds formed between the POSS and the PDMS network) density increases. Further, G is found to have a strong dependence on cross-linking topology. The increase in shear modulus, G, for POSS filled PDMS is significantly higher than that for unfilled PDMS cross-linked with standard molecular species, suggesting an enhanced reinforcement mechanism for POSS. In contrast, in blended systems (POSS/PDMS mixture with no cross-linking) G was not observed to significantly increase with POSS loading. Finally, we find intriguing differences in the structural arrangement of bond strains between the cross-linked and the blended systems. In the unfilled PDMS the distribution of highly strained bonds appears to be random, while in the POSS filled system, the strained bonds form a netlike distribution that spans the network. Such a distribution may form a structural network "holding" the composite together and resulting in increases in G compared to an unfilled, cross-linked system. These results are of importance for engineering of new POSS-based multifunctional materials with tailor-made mechanical properties.

  15. Novel thermoplastic vulcanizates (TPVs based on silicone rubber and polyamide exploring peroxide cross-linking

    Directory of Open Access Journals (Sweden)

    K. Naskar

    2014-04-01

    Full Text Available Novel thermoplastic vulcanizates (TPVs based on silicone rubber (PDMS and polyamide (PA12 have been prepared by dynamic vulcanization process. The effect of dynamic vulcanization and influence of various types of peroxides as cross-linking agents were studied in detail. All the TPVs were prepared at a ratio of 50/50 wt% of silicone rubber and polyamide. Three structurally different peroxides, namely dicumyl peroxide (DCP, 3,3,5,7,7-pentamethyl 1,2,4-trioxepane (PMTO and cumyl hydroperoxide (CHP were taken for investigation. Though DCP was the best option for curing the silicone rubber, at high temperature it suffers from scorch safety. An inhibitor 2,2,6,6-tetramethylpiperidinyloxyl (TEMPO was added with DCP to stabilize the radicals in order to increase the scorch time. Though CHP (hydroperoxide had higher half life time than DCP at higher temperature, it has no significant effect on cross-linking of silicone rubber. PMTO showed prolonged scorch safety and better cross-linking efficiency rather than the other two. TPVs of DCP and PMTO were made up to 11 minutes of mixing. Increased values of tensile strength and elongation at break of PMTO cross-linked TPV indicate the superiority of PMTO. Scanning electron micrographs correlate with mechanical properties of the TPVs. High storage modulus (E' and lower loss tangent value of the PMTO cross-linked TPV indicate the higher degree of cross-linking which is also well supported by the overall cross-link density value. Thus PMTO was found to be the superior peroxide for cross-linking of silicone rubber at high temperature.

  16. Fine-tuned characterization at the solid/solution interface of organotin compounds grafted onto cross-linked polystyrene by using high-resolution MAS NMR spectroscopy.

    Science.gov (United States)

    Martins, José C; Mercier, Frédéric A G; Vandervelden, Alexander; Biesemans, Monique; Wieruszeski, Jean-Michel; Humpfer, Eberhard; Willem, Rudolph; Lippens, Guy

    2002-08-02

    The structural characterization of organotin compounds that are grafted onto insoluble cross-linked polymers has necessarily been limited to elemental analysis, infrared spectroscopy, and in a few instances, solid-state NMR spectroscopy. This important bottleneck in the development of such grafted systems has been addressed by using high-resolution magic angle spinning (hr-MAS) NMR spectroscopy. The great potential of this technique is demonstrated through the structural characterization of diphenylbutyl-(3,4) and dichlorobutylstannanes (5,6), grafted onto divinylbenzene cross-linked polystyrene by means of a suitable linker (1, 2). First, conditions suitable for the application of hr-MAS NMR spectroscopy were identified by characterizing the (1)H resonance line widths of the grafted organotin moiety following swelling of the functionalized beads in eight representative solvents. The presence of clearly identifiable tin coupling patterns in both the 1D (13)C and 2D (1)H-(13)C HSQC spectra, and the incorporation of (119)Sn chemical shift and connectivity information from hr-MAS 1D (119)Sn and 2D (1)H-(119)Sn HMQC spectra, provide an unprecedented level of characterization of grafted organotins directly at the solid/liquid interface. In addition, the use of hr-MAS (119)Sn NMR for reaction monitoring, impurity detection, and quantification and assessment of the extent of coordination reveals its promise as a novel tool for the investigation of polymer-grafted organotin compounds. The approach described here should be sufficiently general for extension to a variety of other nuclei of interest in polymer-supported organometallic chemistry.

  17. INFLUENCE OF CHEMICAL CROSS-LINKING ON THE CREEP-BEHAVIOR OF ULTRA-HIGH-MOLECULAR-WEIGHT POLYETHYLENE FIBERS

    NARCIS (Netherlands)

    PENNING, JP; PRAS, HE; PENNINGS, AJ

    1994-01-01

    In this study, the effect of chemical crosslinking on the creep behavior of high-strength fibers, obtained by gel-spinning and subsequent hot-drawing of ultra-high molecular weight polyethylene (UHMWPE), is examined. In the first part of the paper, the general aspects of the creep behavior of these

  18. Confocal Raman spectroscopic analysis of cross-linked ultra-high molecular weight polyethylene for application in artificial hip joints.

    Science.gov (United States)

    Pezzotti, Giuseppe; Kumakura, Tsuyoshi; Yamada, Kiyotaka; Tateiwa, Toshiyuki; Puppulin, Leonardo; Zhu, Wenliang; Yamamoto, Kengo

    2007-01-01

    Confocal spectroscopic techniques are applied to selected Raman bands to study the microscopic features of acetabular cups made of ultra-high molecular weight polyethylene (UHMWPE) before and after implantation in vivo. The micrometric lateral resolution of a laser beam focused on the polymeric surface (or subsurface) enables a highly resolved visualization of 2-D conformational population patterns, including crystalline, amorphous, orthorhombic phase fractions, and oxidation index. An optimized confocal probe configuration, aided by a computational deconvolution of the optical probe, allows minimization of the probe size along the in-depth direction and a nondestructive evaluation of microstructural properties along the material subsurface. Computational deconvolution is also attempted, based on an experimental assessment of the probe response function of the polyethylene Raman spectrum, according to a defocusing technique. A statistical set of high-resolution microstructural data are collected on a fully 3-D level on gamma-ray irradiated UHMWPE acetabular cups both as-received from the maker and after retrieval from a human body. Microstructural properties reveal significant gradients along the immediate material subsurface and distinct differences are found due to the loading history in vivo, which cannot be revealed by conventional optical spectroscopy. The applicability of the confocal spectroscopic technique is valid beyond the particular retrieval cases examined in this study, and can be easily extended to evaluate in-vitro tested components or to quality control of new polyethylene brands. Confocal Raman spectroscopy may also contribute to rationalize the complex effects of gamma-ray irradiation on the surface of medical grade UHMWPE for total joint replacement and, ultimately, to predict their actual lifetime in vivo.

  19. Review of current indications for combined very high fluence collagen cross-linking and laser in situ keratomileusis surgery

    Directory of Open Access Journals (Sweden)

    Anastasios John Kanellopoulos

    2013-01-01

    Full Text Available In this brief review we will discuss the reasoning and evolution of our current use of combined very high-fluence collagen crosslinking and laser in situ keratomileusis. Several presentations and pertinent publications are reviewed, along with the key steps of the enhanced LASIK procedure. Long term outcome data support the safety and efficacy of LASIK Xtra in stabilizing myopic but also hyperopic LASIK results.In conclusion, we have compelling evidence that LASIK Xtra is a safe and effective adjunct.

  20. Sub-6 nm Thin Cross-Linked Dopamine Films with High Pressure Stability for Organic Solvent Nanofiltration

    KAUST Repository

    Perez Manriquez, Liliana

    2016-07-11

    Interfacial polymerization of dopamine and terephtaloyl chloride is performed on a porous crosslinked polyacrylonitrile support membrane. The resulting polymer layer has a smooth surface and is ultrathin (about 5 nm). The chemical nature of the interfacially polymerized layer is characterized by Fourier transform infrared spectroscopy and by X-ray photoelectron spectroscopy. The thin-film composite membrane is stable in aggressive solvents like dimethylformamide (DMF) and the membrane shows high solvent permeances combined with a molecular weight cut-off below 800 g mol-1. The remarkable stability in DMF, the ease of preparation as well as the extremely thin and smooth selective layer make this new type of bioinspired membrane attractive for solvent resistant nanofiltration. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  1. Cross-linked branching nanohybrid polymer electrolyte with monodispersed TiO2 nanoparticles for high performance lithium-ion batteries

    Science.gov (United States)

    Ma, Cheng; Zhang, Jinfang; Xu, Mingquan; Xia, Qingbing; Liu, Jiatu; Zhao, Shuai; Chen, Libao; Pan, Anqiang; Ivey, Douglas G.; Wei, Weifeng

    2016-06-01

    Nanohybrid polymer electrolytes (NHPE) with ceramic particles have attracted significant attention owing to their improvement in electrochemical performance. However, particle aggregation and weak nanoparticle/polymer matrix interaction restrict their further application in lithium-ion batteries (LIBs). We demonstrate a facile in-situ polymerization/crystallization method to synthesize a homogeneous TiO2-grafted NHPE with a cross-linked branching structure, comprised of ion-conducting poly(ethylene glycol) methyl ether methacrylate (PEGMEM) and non-polar stearyl methacrylate (SMA). This technique is different from existing methods of blending functionalized ceramic particles into the polymer matrix. Highly monodispersed TiO2 nanocrystals enhance the effective interfacial interactions between particles and polymer matrix, which suppress the crystallization of ethylene oxide (EO) groups and facilitate forming continuously interconnected ion-conducting channels. Moreover, an increased dissociation degree of Li salt can also be achieved. The TiO2-grafted NHPE exhibits superior electrochemical properties with an ionic conductivity of 1.1 × 10-4 S cm-1 at 30 °C, a high lithium ion transference number and excellent interfacial compatibility with the lithium electrode. In particular, a lithium-ion battery based on TiO2-grafted NHPE demonstrates good C-rate performance, as well as excellent cycling stability with an initial discharge capacity of 153.5 mAh g-1 and a capacity retention of 96% after 300 cycles at 1 C (80 °C).

  2. Collagen cross linking: Current perspectives

    Directory of Open Access Journals (Sweden)

    Srinivas K Rao

    2013-01-01

    Full Text Available Keratoconus is a common ectatic disorder occurring in more than 1 in 1,000 individuals. The condition typically starts in adolescence and early adulthood. It is a disease with an uncertain cause and its progression is unpredictable, but in extreme cases, vision deteriorates and can require corneal transplant surgery. Corneal collagen cross-linking (CCL with riboflavin (C3R is a recent treatment option that can enhance the rigidity of the cornea and prevent disease progression. Since its inception, the procedure has evolved with newer instrumentation, surgical techniques, and is also now performed for expanded indications other than keratoconus. With increasing experience, newer guidelines regarding optimization of patient selection, the spectrum of complications and their management, and combination procedures are being described. This article in conjunction with the others in this issue, will try and explore the uses of collagen cross-linking (CXL in its current form.

  3. Comparison of 10-year clinical wear of annealed and remelted highly cross-linked polyethylene: A propensity-matched cohort study.

    Science.gov (United States)

    Hamai, Satoshi; Nakashima, Yasuharu; Mashima, Naohiko; Yamamoto, Takuaki; Kamada, Tomomi; Motomura, Goro; Imai, Hiroshi; Fukushi, Jun-Ichi; Miura, Hiromasa; Iwamoto, Yukihide

    2016-06-01

    No previous studies comparing the clinical wear rates of the two different kinds of cross-linked ultra-high-molecular-weight polyethylene (XLPE), annealed and remelted, are available. We compared the creep and steady wear rates of 36 matched pairs (72 hips in total) adjusting for baseline characteristics with propensity score matching techniques. Zirconia femoral heads with 26-mm diameter were used in all cases. The femoral-head cup penetration was measured digitally on radiographs. Significantly greater creep (p=0.006) was detected in the remelted (0.234mm) than annealed (0.159mm) XLPE. However, no significant difference (p=0.19) was found between the steady wear rates (0.003 and 0.008mm/year, respectively) of the annealed and remelted XLPE. Multiple regression analyses showed that remelted XLPE is significant independent variable (p0.05) on the steady wear rates. No patients exhibited above the osteolysis threshold of 0.1mm/year, progressive radiolucencies, osteolysis, or polyethylene fracture. This propensity-matched cohort study document no significant difference in wear resistant performances of annealed and remelted XLPE over an average period of 10 years.

  4. Cross-linked polybenzimidazole membranes for high temperature proton exchange membrane fuel cells with dichloromethyl phosphinic acid as a cross-linker

    DEFF Research Database (Denmark)

    Noye, Pernille; Li, Qingfeng; Pan, Chao;

    2008-01-01

    . The produced cross-linked membranes show increased mechanical strength, making it possible to achieve higher phosphoric acid doping levels and therefore higher proton conductivity. Oxidative stability is significantly improved and thermal stability is sufficient in a temperature range of up to 250 degrees C, i......Phosphoric acid doped polybenzimidazole (PBI) membranes have been covalently cross-linked with dichloromethyl phosphinic acid (DCMP). FT-IR measurements showed new bands originating from bonds between the hydrogen bearing nitrogen in the imidazole group of PBI and the CH2 group in DCMP...

  5. 2500 high-quality genomes reveal that the biogeochemical cycles of C, N, S and H are cross-linked by metabolic handoffs in the terrestrial subsurface

    Science.gov (United States)

    Anantharaman, K.; Brown, C. T.; Hug, L. A.; Sharon, I.; Castelle, C. J.; Shelton, A.; Bonet, B.; Probst, A. J.; Thomas, B. C.; Singh, A.; Wilkins, M.; Williams, K. H.; Tringe, S. G.; Beller, H. R.; Brodie, E.; Hubbard, S. S.; Banfield, J. F.

    2015-12-01

    Microorganisms drive the transformations of carbon compounds in the terrestrial subsurface, a key reservoir of carbon on earth, and impact other linked biogeochemical cycles. Our current knowledge of the microbial ecology in this environment is primarily based on 16S rRNA gene sequences that paint a biased picture of microbial community composition and provide no reliable information on microbial metabolism. Consequently, little is known about the identity and metabolic roles of the uncultivated microbial majority in the subsurface. In turn, this lack of understanding of the microbial processes that impact the turnover of carbon in the subsurface has restricted the scope and ability of biogeochemical models to capture key aspects of the carbon cycle. In this study, we used a culture-independent, genome-resolved metagenomic approach to decipher the metabolic capabilities of microorganisms in an aquifer adjacent to the Colorado River, near Rifle, CO, USA. We sequenced groundwater and sediment samples collected across fifteen different geochemical regimes. Sequence assembly, binning and manual curation resulted in the recovery of 2,542 high-quality genomes, 27 of which are complete. These genomes represent 1,300 non-redundant organisms comprising both abundant and rare community members. Phylogenetic analyses involving ribosomal proteins and 16S rRNA genes revealed the presence of up to 34 new phyla that were hitherto unknown. Less than 11% of all genomes belonged to the 4 most commonly represented phyla that constitute 93% of all currently available genomes. Genome-specific analyses of metabolic potential revealed the co-occurrence of important functional traits such as carbon fixation, nitrogen fixation and use of electron donors and electron acceptors. Finally, we predict that multiple organisms are often required to complete redox pathways through a complex network of metabolic handoffs that extensively cross-link subsurface biogeochemical cycles.

  6. Gelation threshold of cross-linked polymer brushes.

    Science.gov (United States)

    Hoffmann, Max; Lang, Michael; Sommer, Jens-Uwe

    2011-02-01

    The cross-linking of polymer brushes is studied using the bond-fluctuation model. By mapping the cross-linking process into a two-dimensional (2D) percolation problem within the lattice of grafting points, we investigate the gelation transition in detail. We show that the particular properties of cross-linked polymer brushes can be reduced to the distribution of bonds which are formed between the grafted chains, and we propose scaling arguments to relate the gelation threshold to the chain length and the grafting density. The gelation threshold is lower than the percolation threshold for 2D bond percolation because of the longer range and broad distribution of bonds formed by the cross-linking process. We term this type of percolation problem star percolation. We observe a broad crossover from mean-field to critical percolation behavior by analyzing the cluster size distribution near the gelation threshold.

  7. Electrospinning formaldehyde cross-linked zein solutions

    Science.gov (United States)

    In order to develop zein fibers with improved physical properties and solvent resistance, formaldehyde was used as the cross-linking reagent before spinning. The cross-linking reaction was carried out in either acetic acid or ethanolic-HCl where the amount of cross-linking reagent was between 1 and...

  8. Corneal collagen cross-linking

    Directory of Open Access Journals (Sweden)

    Jankov II Mirko

    2010-01-01

    Full Text Available Corneal collagen cross-linking (CXL with riboflavin and ultraviolet-A (UVA is a new technique of corneal tissue strengthening by using riboflavin as a photosensitizer and UVA to increase the formation of intra- and interfibrillar covalent bonds by photosensitized oxidation. Keratocyte apoptosis in the anterior segment of the corneal stroma all the way down to a depth of about 300 microns has been described and a demarcation line between the treated and untreated cornea has been clearly shown. It is important to ensure that the cytotoxic threshold for the endothelium has not been exceeded by strictly respecting the minimal corneal thickness. Confocal microscopy studies show that repopulation of keratocytes is already visible 1 month after the treatment, reaching its pre-operative quantity and quality in terms of functional morphology within 6 months after the treatment. The major indication for the use of CXL is to inhibit the progression of corneal ectasias, such as keratoconus and pellucid marginal degeneration. CXL may also be effective in the treatment and prophylaxis of iatrogenic keratectasia, resulting from excessively aggressive photoablation. This treatment has also been used to treat infectious corneal ulcers with apparent favorable results. Combination with other treatments, such as intracorneal ring segment implantation, limited topography-guided photoablation and conductive keratoplasty have been used with different levels of success.

  9. Poly(2-methacryloyloxyethyl phosphorylcholine)-grafted highly cross-linked polyethylene liner in primary total hip replacement: one-year results of a prospective cohort study.

    Science.gov (United States)

    Takatori, Yoshio; Moro, Toru; Kamogawa, Morihide; Oda, Hiromi; Morimoto, Shuhei; Umeyama, Takashige; Minami, Manabu; Sugimoto, Hideharu; Nakamura, Shigeru; Karita, Tatsuro; Kim, Juntaku; Koyama, Yurie; Ito, Hideya; Kawaguchi, Hiroshi; Nakamura, Kozo

    2013-06-01

    To control particle-induced osteolysis in total hip replacement (THR), we developed a new technique to graft poly(2-methacryloyloxyethyl phosphorylcholine) onto the surface of polyethylene liners. A prospective cohort study was conducted to investigate the clinical safety of this novel bearing surface. Between April 2007 and September 2008, we recruited a prospective consecutive series of 80 patients in five participating hospitals. These patients received a cementless THR; a 26-mm-diameter cobalt-chromium-molybdenum alloy ball and a poly(2-methacryloyloxyethyl phosphorylcholine)-grafted cross-linked polyethylene liner were used for the bearing couplings. These individuals were followed a year postoperatively. An evaluation of clinical performance was conducted through an assessment of hip joint function based on the evaluation chart authorized by the Japanese Orthopaedic Association. No patients were lost to follow-up. No adverse events were found to be correlated with the implanted liners. The average hip joint function score improved from 43.2 preoperatively to 91.7 postoperatively at 1 year. There was no implant migration nor periprosthetic osteolysis detected on radiographic analysis. On the basis of our results, we conclude that poly(2-methacryloyloxyethyl phosphorylcholine)-grafted cross-linked polyethylene liners are a safe implant option for hip replacement surgery for short-term clinical use.

  10. Effects of vitamin E-diffused highly cross-linked UHMWPE particles on inflammation, apoptosis and immune response against S. aureus.

    Science.gov (United States)

    Chen, Weishen; Bichara, David A; Suhardi, Jeremy; Sheng, Puyi; Muratoglu, Orhun K

    2017-10-01

    Particle-induced osteolysis and periprosthetic joint infection (PJI) are closely associated with periprosthetic tissue immune function. The objective of this study was to determine the effects of polyethylene particles on inflammation and response against S. aureus. Effects that vitamin E-diffused cross-linked UHMWPE (VE-PE) particles had on apoptosis, inflammation, and bactericidal activities compared to virgin cross-linked UHMWPE (control PE) particles were examined. Murine RAW 264.7 macrophages exposed to VE-PE particles in vitro were less apoptotic, secreted less tumor necrosis factor (TNF)-α, and responded more effectively against lipopolysaccharide or S. aureus compared to control PE particles. Implantation of VE-PE particles in murine calvaria in vivo caused less reactive oxygen species generation, less apoptosis, and less osteolysis compared to control PE particles. Implantation of PE particles in mice calvaria for 28 days, followed by inoculation with S. aureus in the same site where PE particles were implanted, demonstrated enhanced S. aureus clearance in the VE-PE group at day 33 after inoculation. These findings indicate that VE-PE particles might be less inflammatory and might preserve innate immunity of local tissue, allowing for enhanced clearance of bacteria. Copyright © 2017. Published by Elsevier Ltd.

  11. Photo-cross-linking of amniotic membranes for limbal epithelial cell cultivation

    Energy Technology Data Exchange (ETDEWEB)

    Lai, Jui-Yang, E-mail: jylai@mail.cgu.edu.tw

    2014-12-01

    In the present study, we developed photo-cross-linked amniotic membrane (AM) as a limbal stem cell niche. After ultraviolet (UV) irradiation for varying time periods, the biological tissues were studied by determinations of cross-linking structure, degradability, and nutrient permeation ability. Our results showed that the number of cross-links per unit mass of AM significantly increased with increasing illumination time from 5 to 50 min. However, the cross-link formation was inhibited by longer irradiation time (i.e., 150 min), probably due to the scission of tissue collagen chains through irradiation. The biological stability and matrix permeability of photo-cross-linked AM materials strongly depended on their cross-linking densities affected by the UV irradiation. In vitro biocompatibility studies including cell viability and pro-inflammatory gene expression analyses demonstrated that, irrespective of the irradiation time employed, the physically cross-linked biological tissues exhibited negligible cytotoxicity and similar interleukin-6 (IL-6) mRNA levels. The data clearly indicate that these AM matrices do not cause potential harm to the corneal epithelial cells. After the growth of limbal epithelial cells (LECs) on AM substrates, Western blot analyses were conducted to examine the expression of ABCG2. It was found that the ability of UV-irradiated AM to maintain the undifferentiated precursor cell phenotype was significantly enhanced with increasing extent of photo-cross-linking. In summary, the UV irradiation time may have a profound influence on the fabrication of photo-cross-linked AM matrices for LEC cultivation. - Highlights: • We report the development of photo-cross-linked AM as a limbal stem cell niche. • Cross-linked structure of tissue materials was controlled by UV irradiation time. • Biostability and matrix permeability of AM depended on cross-linking density. • All the studied photo-cross-linked AM showed good in vitro biocompatibility.

  12. DC conduction and breakdown characteristics of Al2O3/cross-linked polyethylene nanocomposites for high voltage direct current transmission cable insulation

    Science.gov (United States)

    Park, Yong-Jun; Kwon, Jung-Hun; Sim, Jae-Yong; Hwang, Ju-Na; Seo, Cheong-Won; Kim, Ji-Ho; Lim, Kee-Joe

    2014-08-01

    We have discussed a cross-linked polyethylene (XLPE) nanocomposite insulating material that is able to DC voltage applications. Nanocomposites, which are composed in polymer matrix mixed with nano-fillers, have received considerable attention because of their potential benefits as dielectrics. The nano-sized alumina oxide (Al2O3)/XLPE nanocomposite was prepared, and three kinds of test, such as DC breakdown, DC polarity reversal breakdown, and volume resistivity were performed. By the addition of nano-sized Al2O3 filler, both the DC breakdown strength and the volume resistivity of XLPE were increased. A little homogeneous space charge was observed in Al2O3/XLPE nanocomposite material in the vicinity of electrode through the polarity reversal breakdown test. From these results, it is thought that the addition of Al2O3 nano-filler is effective for the improvement of DC electrical insulating properties of XLPE.

  13. Chemical cross-linking of Chlamydia trachomatis

    DEFF Research Database (Denmark)

    Birkelund, Svend; Lundemose, AG; Christiansen, Gunna

    1988-01-01

    Purified elementary bodies (EBs) of Chlamydia trachomatis serovar L2 were analyzed by chemical cross-linking with disuccinimidyl selenodipropionate. The effect of the cross-linking was analyzed by immunoblotting sodium dodecyl sulfate-polyacrylamide gel electrophoresis-separated components which...

  14. Photo-cross-linked poly(ethylene carbonate) elastomers: synthesis, in vivo degradation, and determination of in vivo degradation mechanism.

    Science.gov (United States)

    Cornacchione, L A; Qi, B; Bianco, J; Zhou, Z; Amsden, B G

    2012-10-01

    Low-molecular-weight poly(ethylene carbonate) diols of varying molecular weight were generated through catalyzed thermal degradation of high-molecular-weight poly(ethylene carbonate). These polymers were then end functionalized with acrylate groups. The resulting α,ω-diacrylates were effectively photo-cross-linked upon exposure to long-wave UV light in the presence of a photoinitiator to yield rubbery networks of low sol content. The degree of cross-linking effectively controlled the in vivo degradation rate of the networks by adherent macrophages; higher cross-link densities yielded slower degradation rates. The cross-link density did not affect the number of adherent macrophages at the elastomer/tissue interface, indicating that cross-linking affected the susceptibility of the elastomer to degradative species released by the macrophages. The reactive species likely responsible for in vivo degradation appears to be superoxide anion, as the in vivo results were in agreement with in vitro degradation via superoxide anion, while cholesterol esterase, known to degrade similar poly(alkylene carbonate)s, had no affect on elastomer degradation.

  15. The Cross - linking reaction of HEC

    Institute of Scientific and Technical Information of China (English)

    XIONG Jian; YE Jun; XUAN Zhiyong; XIE Guohui

    2001-01-01

    @@ Cellulose ethers are important components for light industries such as food and papermaking industries. Its modification research is a frontline science to widen their uses and realize their industrialization. The target of modification is to make high production value, low input and meet the needs better in industries. O-(2-hydroxyethl) cellulose (HEC) is one of the best-known cellulose ether derivatives. It is mainly used as thickeners, dispersants, adhesives, extenders, and films because of its water solubility and gel-forming properties. The present research,by means of cross-linking, we study the influence on HEC about rheological behavior.This will provide a feasible scheme for cellulose ethers modification.

  16. The Cross - linking reaction of HEC

    Institute of Scientific and Technical Information of China (English)

    XIONG; Jian

    2001-01-01

    Cellulose ethers are important components for light industries such as food and papermaking industries. Its modification research is a frontline science to widen their uses and realize their industrialization. The target of modification is to make high production value, low input and meet the needs better in industries.  O-(2-hydroxyethl) cellulose (HEC) is one of the best-known cellulose ether derivatives. It is mainly used as thickeners, dispersants, adhesives, extenders, and films because of its water solubility and gel-forming properties. The present research,by means of cross-linking, we study the influence on HEC about rheological behavior.This will provide a feasible scheme for cellulose ethers modification.……

  17. Yield and Failure Behavior Investigated for Cross-Linked Phenolic Resins Using Molecular Dynamics

    Science.gov (United States)

    Monk, Joshua D.; Lawson, John W.

    2016-01-01

    Molecular dynamics simulations were conducted to fundamentally evaluate the yield and failure behavior of cross-linked phenolic resins at temperatures below the glass transition. Yield stress was investigated at various temperatures, strain rates, and degrees of cross-linking. The onset of non-linear behavior in the cross-linked phenolic structures was caused by localized irreversible molecular rearrangements through the rotation of methylene linkers followed by the formation or annihilation of neighboring hydrogen bonds. The yield stress results, with respect to temperature and strain rate, could be fit by existing models used to describe yield behavior of amorphous glasses. The degree of cross-linking only indirectly influences the maximum yield stress through its influence on glass transition temperature (Tg), however there is a strong relationship between the degree of cross-linking and the failure mechanism. Low cross-linked samples were able to separate through void formation, whereas the highly cross-linked structures exhibited bond scission.

  18. The effect of cross-link distributions in axially-ordered, cross-linked networks

    Science.gov (United States)

    Bennett, C. Brad; Kruczek, James; Rabson, D. A.; Matthews, W. Garrett; Pandit, Sagar A.

    2013-07-01

    Cross-linking between the constituent chains of biopolymers has a marked effect on their materials’ properties. In certain of these materials, such as fibrillar collagen, increases in cross-linking lead to an increase in the melting temperature. Fibrillar collagen is an axially-ordered network of cross-linked polymer chains exhibiting a broadened denaturation transition, which has been explained in terms of the successive denaturation with temperature of multiple species. We model axially-ordered, cross-linked materials as stiff chains with distinct arrangements of cross-link-forming sites. Simulations suggest that systems composed of chains with identical arrangements of cross-link-forming sites exhibit critical behavior. In contrast, systems composed of non-identical chains undergo a crossover. This model suggests that the arrangement of cross-link-forming sites may contribute to the broadening of the denaturation transition in fibrillar collagen.

  19. Betanin reduces the accumulation and cross-links of collagen in high-fructose-fed rat heart through inhibiting non-enzymatic glycation.

    Science.gov (United States)

    Han, Junyan; Tan, Chang; Wang, Yiheng; Yang, Shaobin; Tan, Dehong

    2015-02-05

    We attempted to determine whether betanin (from natural pigments) that has antioxidant properties would be protective against fructose-induced diabetic cardiac fibrosis in Sprague-Dawley rats. Fructose water solution (30%) was accessed freely, and betanin (25 and 100 mg/kg/d) was administered by intra-gastric gavage continuously for 60 d. Rats were sacrificed after overnight fast. The rat blood and left ventricle were collected. In vitro antiglycation assay in bovine serum albumin/fructose system was also performed. In rats treated only with fructose, levels of plasma markers: glucose, insulin, HOMA and glycated hemoglobin rised, left ventricle collagen accumulated and cross-linked, profibrotic factor-transforming growth factor (TGF)-β1 and connective tissue growth factor (CTGF) protein expression increased, and soluble collagen decreased, compared with those in normal rats, showing fructose induces diabetic cardiac fibrosis. Treatment with betanin antagonized the changes of these parameters, demonstrating the antifibrotic role of betanin in the selected diabetic models. In further mechanistic study, betanin decreased protein glycation indicated by the decreased levels of protein glycation reactive intermediate (methylglyoxal), advanced glycation end product (N(ε)-(carboxymethyl) lysine) and receptors for advanced glycation end products (AGEs), antagonized oxidative stress and nuclear factor-κB activation elicited by fructose feeding, suggesting inhibition of glycation, oxidative stress and nuclear factor-κB activation may be involved in the antifibrotic mechanisms. Betanin also showed anitglycative effect in BSA/fructose system, which supported that anitglycation was involved in betanin's protective roles in vivo. Taken together, the potential for using betanin as an auxillary therapy for diabetic cardiomyopathy deserves to be explored further.

  20. Preliminary Characterization of Genipin-Cross-Linked Silk Sericin/Poly(vinyl alcohol Films as Two-Dimensional Wound Dressings for the Healing of Superficial Wounds

    Directory of Open Access Journals (Sweden)

    Tippawan Siritientong

    2013-01-01

    Full Text Available The genipin-cross-linked silk sericin/poly(vinyl alcohol (PVA films were developed aiming to be applied as two-dimensional wound dressings for the treatment of superficial wounds. The effects of genipin cross-linking concentration on the physical and biological properties of the films were investigated. The genipin-cross-linked silk sericin/PVA films showed the increased surface density, tensile strength, and percentage of elongation, but decreased percentage of light transmission, water vapor transmission rate, and water swelling, compared to the non-cross-linked films. This explained that the cross-linking bonds between genipin and silk sericin would reduce the mobility of molecular chains within the films, resulting in the more rigid molecular structure. Silk sericin was released from the genipin-cross-linked films in a sustained manner. In addition, either L929 mouse fibroblast or HaCat keratinocyte cells showed high percentage of viability when cultured on the silk sericin/PVA films cross-linked with 0.075 and 0.1% w/v genipin. The in vivo safety test performed according to ISO 10993-6 confirmed that the genipin-cross-linked silk sericin/PVA films were safe for the medical usages. The efficacy of the films for the treatment of superficial skin wounds will be further investigated in vivo and clinically. The genipin-cross-linked silk sericin/PVA films would be promising choices of two-dimensional wound dressings for the treatment of superficial wounds.

  1. Effectiveness of trimethylopropane trimethacrylate for the electron-beam-irradiation-induced cross-linking of polylactic acid

    Energy Technology Data Exchange (ETDEWEB)

    Ng, Hon-Meng [Department of Chemical Engineering, Faculty of Engineering and Science, Universiti Tunku Abdul Rahman, Jalan Genting Kelang, 53300 Setapak, Kuala Lumpur (Malaysia); Bee, Soo-Tueen, E-mail: beest@utar.edu.my [Department of Chemical Engineering, Faculty of Engineering and Science, Universiti Tunku Abdul Rahman, Jalan Genting Kelang, 53300 Setapak, Kuala Lumpur (Malaysia); Ratnam, C.T. [Radiation Processing Technology Division, Malaysian Nuclear Agency, Bangi, 43000 Kajang, Selangor (Malaysia); Sin, Lee Tin; Phang, Yee-Yao; Tee, Tiam-Ting [Department of Chemical Engineering, Faculty of Engineering and Science, Universiti Tunku Abdul Rahman, Jalan Genting Kelang, 53300 Setapak, Kuala Lumpur (Malaysia); Rahmat, A.R. [Department of Polymer Engineering, Faculty of Chemical Engineering, Universiti Teknologi Malaysia, 81310 UTM Skudai, Johor (Malaysia)

    2014-01-15

    Highlights: • Investigation of trimethylopropane trimethacrylate (TMPTMA) on electron beam irradiated PLA. • Irradiated PLA blends were weakened by incorporation of high amount of TMPTMA. • TMPTMA interacts with polymer free radicals to build crosslinking network. -- Abstract: The purpose of this research was to investigate the effects of various loading levels of trimethylopropane trimethacrylate (TMPTMA) on the properties of polylactic acid (PLA) cross-linked via electron-beam irradiation. PLA was compounded with 3–5 wt.% of TMPTMA to induce cross-linking upon subjection to electron-beam irradiation doses of 25–250 kGy. The physical properties of the PLA samples were characterised by means of X-ray diffraction, gel fraction and scanning electron microscopy analyses on fractured surfaces after tensile tests. The presence of TMPTMA in PLA was found to effectively increase the crystallite size and gel fraction. However, higher loading levels of TMPTMA could compromise the properties of the PLA/TMPTMA samples, indicating that a larger amount of monomer free radicals might promote degradation within the substantially cross-linked amorphous phase. Irradiation-induced cross-linking in the samples could improve the cross-linking density while decreasing the elongation and interfering with the crystallisation. These effects are caused by the intensive irradiation-induced chain scission that is responsible for the deterioration of the mechanical and crystalline properties of the samples.

  2. FTIR Spectroscopic Studies on Cross Linking of SU-8 Photoresist

    Science.gov (United States)

    Kalaiselvi, S. M. P.; Tan, T. L.; Rawat, R. S.; Lee, P.; Heussler, S. P.; Breese, M. B. H.

    2013-11-01

    The usage of chemically-amplified, negative tone SU-8 photoresist is numerous, spanning industrial, scientific and medical fields. Hence, in this study, some preliminary studies were conducted to understand the dosage and heat treatment requirements of the SU-8 photoresist essential for pattern generation using X-ray lithography. In this work, using Synchrotron as the X-ray source, SU-8 photoresist was characterized for X-ray lithography in terms of its process parameters such as X-ray exposure dose, post exposure bake (PEB) time and temperature for various photoresist thicknesses which is considered worthwhile in view of applications of SU-8 for the fabrication of very high aspect ratio micro structures. The process parameters were varied and the resultant cross linking of the molecular chains of the photoresist was accurately monitored using a Fourier Transform Infra-Red (FTIR) spectrometer and the results are discussed. The infrared absorption peak at 914 cm-1 in the spectrum of the SU-8 photoresist was found to be a useful indicator for the completion of cross linking in the SU-8 photoresist. Results show that the cross linking of the SU-8 photoresist is at a higher rate from 0 J/cm3 to 30 J/cm3 after which the peak almost saturates regardless of the PEB time. It is a good evidence for the validation of dosage requirement of SU-8 photoresist for effective completion of cross linking, which in turn is a requirement for efficient fabrication of micro and nano structures. An analogous behavior was also observed between the extent of cross linking and the PEB time and temperature. The rate of cross linking declines after a certain period of PEB time regardless of PEB temperature. The obtained results also show a definite relation between variation of the absorbance area of the peak at 914 cm-1 and the X-ray exposure dose.

  3. Blind testing of cross-linking/mass spectrometry hybrid methods in CASP11.

    Science.gov (United States)

    Schneider, Michael; Belsom, Adam; Rappsilber, Juri; Brock, Oliver

    2016-09-01

    Hybrid approaches combine computational methods with experimental data. The information contained in the experimental data can be leveraged to probe the structure of proteins otherwise elusive to computational methods. Compared with computational methods, the structures produced by hybrid methods exhibit some degree of experimental validation. In spite of these advantages, most hybrid methods have not yet been validated in blind tests, hampering their development. Here, we describe the first blind test of a specific cross-link based hybrid method in CASP. This blind test was coordinated by the CASP organizers and utilized a novel, high-density cross-linking/mass-spectrometry (CLMS) approach that is able to collect high-density CLMS data in a matter of days. This experimental protocol was developed in the Rappsilber laboratory. This approach exploits the chemistry of a highly reactive, photoactivatable cross-linker to produce an order of magnitude more cross-links than homobifunctional cross-linkers. The Rappsilber laboratory generated experimental CLMS data based on this protocol, submitted the data to the CASP organizers which then released this data to the CASP11 prediction groups in a separate, CLMS assisted modeling experiment. We did not observe a clear improvement of assisted models, presumably because the properties of the CLMS data-uncertainty in cross-link identification and residue-residue assignment, and uneven distribution over the protein-were largely unknown to the prediction groups and their approaches were not yet tailored to this kind of data. We also suggest modifications to the CLMS-CASP experiment and discuss the importance of rigorous blind testing in the development of hybrid methods. Proteins 2016; 84(Suppl 1):152-163. © 2016 The Authors Proteins: Structure, Function, and Bioinformatics Published by Wiley Periodicals, Inc.

  4. Cross-linked structure of network evolution

    Science.gov (United States)

    Bassett, Danielle S.; Wymbs, Nicholas F.; Porter, Mason A.; Mucha, Peter J.; Grafton, Scott T.

    2014-03-01

    We study the temporal co-variation of network co-evolution via the cross-link structure of networks, for which we take advantage of the formalism of hypergraphs to map cross-link structures back to network nodes. We investigate two sets of temporal network data in detail. In a network of coupled nonlinear oscillators, hyperedges that consist of network edges with temporally co-varying weights uncover the driving co-evolution patterns of edge weight dynamics both within and between oscillator communities. In the human brain, networks that represent temporal changes in brain activity during learning exhibit early co-evolution that then settles down with practice. Subsequent decreases in hyperedge size are consistent with emergence of an autonomous subgraph whose dynamics no longer depends on other parts of the network. Our results on real and synthetic networks give a poignant demonstration of the ability of cross-link structure to uncover unexpected co-evolution attributes in both real and synthetic dynamical systems. This, in turn, illustrates the utility of analyzing cross-links for investigating the structure of temporal networks.

  5. Cross-linked structure of network evolution

    Energy Technology Data Exchange (ETDEWEB)

    Bassett, Danielle S., E-mail: dsb@seas.upenn.edu [Department of Bioengineering, University of Pennsylvania, Philadelphia, Pennsylvania 19104 (United States); Department of Physics, University of California, Santa Barbara, California 93106 (United States); Sage Center for the Study of the Mind, University of California, Santa Barbara, California 93106 (United States); Wymbs, Nicholas F.; Grafton, Scott T. [Department of Psychology and UCSB Brain Imaging Center, University of California, Santa Barbara, California 93106 (United States); Porter, Mason A. [Oxford Centre for Industrial and Applied Mathematics, Mathematical Institute, University of Oxford, Oxford OX2 6GG (United Kingdom); CABDyN Complexity Centre, University of Oxford, Oxford, OX1 1HP (United Kingdom); Mucha, Peter J. [Carolina Center for Interdisciplinary Applied Mathematics, Department of Mathematics, University of North Carolina, Chapel Hill, North Carolina 27599 (United States); Department of Applied Physical Sciences, University of North Carolina, Chapel Hill, North Carolina 27599 (United States)

    2014-03-15

    We study the temporal co-variation of network co-evolution via the cross-link structure of networks, for which we take advantage of the formalism of hypergraphs to map cross-link structures back to network nodes. We investigate two sets of temporal network data in detail. In a network of coupled nonlinear oscillators, hyperedges that consist of network edges with temporally co-varying weights uncover the driving co-evolution patterns of edge weight dynamics both within and between oscillator communities. In the human brain, networks that represent temporal changes in brain activity during learning exhibit early co-evolution that then settles down with practice. Subsequent decreases in hyperedge size are consistent with emergence of an autonomous subgraph whose dynamics no longer depends on other parts of the network. Our results on real and synthetic networks give a poignant demonstration of the ability of cross-link structure to uncover unexpected co-evolution attributes in both real and synthetic dynamical systems. This, in turn, illustrates the utility of analyzing cross-links for investigating the structure of temporal networks.

  6. Analytical characterisation of glutardialdehyde cross-linking products in gelatine-gum arabic complex coacervates

    Energy Technology Data Exchange (ETDEWEB)

    Fuguet, Elisabet [Advanced Measurement and Imaging, Unilever Food and Health Research Institute, Olivier van Noortlaan 120, 3133 AT Vlaardingen (Netherlands)], E-mail: eli.fuguet@gmail.com; Platerink, Chris van [Advanced Measurement and Imaging, Unilever Food and Health Research Institute, Olivier van Noortlaan 120, 3133 AT Vlaardingen (Netherlands); Department of Biomolecular Mass Spectrometry, Bijvoet Center for Biomolecular Research, Utrecht University, Sorbonnelaan 16, 3584 CA Utrecht (Netherlands); Janssen, Hans-Gerd [Advanced Measurement and Imaging, Unilever Food and Health Research Institute, Olivier van Noortlaan 120, 3133 AT Vlaardingen (Netherlands); van' t Hoff Institute for Molecular Sciences, University of Amsterdam, Nieuwe Achtergracht 166, 1018 WV Amsterdam (Netherlands)

    2007-11-26

    Encapsulates having shells of cross-linked mixtures of proteins and polysaccharides are widely used in the food and pharmaceutical industry for controlled release of actives and flavour compounds. In order to be able to predict the behaviour and the release characteristics of the microcapsules, a better understanding of the nature and extent of the cross-linking reaction is needed. Several analytical techniques were applied for the characterisation of glutardialdehyde (GDA) cross-linked encapsulates made of gelatine and gum arabic. To allow the use of sensitive, high-resolution methods such as chromatography and mass spectrometry, the sample first had to be hydrolysed. In this way, a mixture of amino acids, small peptides and the cross-link moieties was obtained. High-resolution liquid chromatography coupled to high-resolution mass spectrometry (HPLC-MS) was applied to detect possible cross-link markers through a comparison of HPLC-MS mass-chromatograms obtained for cross-linked and non-cross-linked coacervates. HPLC-MS/MS was used to identify the species responsible for the differences. Cross-linking occurred between GDA molecules and lysine and hydroxylysine {epsilon}-amino groups, and up to eight cross-link products of different nature could be identified. They included pyridinium ions and Schiff bases, and also unreacted GDA condensation products. Next, based on the insight gained in the possible chemical structures present in the cross-link markers, methods for selective labelling of these functionalities were employed to allow easier detection of related reaction products. Both liquid chromatography (LC) and gas chromatography (GC) were used in these experiments. Unfortunately, these approaches failed to detect new cross-link markers, most likely as a result of the low levels at which these are present.

  7. Method of preparing cross-linked enzyme particles

    NARCIS (Netherlands)

    Mateo, C.; Van Langen, L.M.; Van Rantwijk, F.

    2004-01-01

    The invention relates to a method of preparing cross-linked enzyme particles using a cross-linking agent. According to the invention, the enzyme particles are formed and subsequently cross-linked using a cross-linking agent having at least n reactive groups where N>=3 and a molecular weight of

  8. Method of preparing cross-linked enzyme particles

    NARCIS (Netherlands)

    Mateo, C.; Van Langen, L.M.; Van Rantwijk, F.

    2004-01-01

    The invention relates to a method of preparing cross-linked enzyme particles using a cross-linking agent. According to the invention, the enzyme particles are formed and subsequently cross-linked using a cross-linking agent having at least n reactive groups where N>=3 and a molecular weight of >2,00

  9. The cross linking of EPDM and NBR rubber

    Directory of Open Access Journals (Sweden)

    Samardžija-Jovanović Suzana

    2005-01-01

    Full Text Available In the process of macromolecule cross linking, the choice of type and quantity of the components and the experimental conditions are important to obtain the new cross linked materials with better mechanical and chemical characteristics. The cross linking method depends on the rubber type and structure. Intermolecular cross linking results in the formation elastomer network. The basis of the cross linking process, between ethylene propylene diene rubber (EPDM and acrylonitrile butadiene rubber (NBR, is a chemical reaction. Fillers and other additives are present in different mass ratios in the material. The exploitation properties of the cross linked materials depend on the quantity of additive in the cross linked systems.

  10. Synthesis and Properties of Cross-Linked Polyamide Aerogels

    Science.gov (United States)

    Williams, Jarrod C.; Meador, Mary Ann; McCorkle, Linda

    2015-01-01

    We report the first synthesis of cross-linked polyamide aerogels through step growth polymerization using a combination of diamines, diacid chloride and triacid chloride. Polyamide oligomers endcapped with amines are prepared as stable solutions in N-methylpyrrolidinone from several different diamine precursors and 1,3-benzenedicarbonyl dichloride. Addition of 1,3,5-benzenetricarbonyl trichloride yields gels which form in under five minutes according to the scheme shown. Solvent exchange of the gels into ethanol, followed by drying using supercritical CO2 extraction gives colorless aerogels with densities around 0.1 to 0.2 gcm3. Thicker monolithes of the polyamide aerogels are stiff and strong, while thin films of certain formulations are highly flexible, durable, and even translucent. These materials may have use as insulation for deployable space structures, rovers, habitats or extravehicular activity suits as well as in many terrestrial applications. Strucure property relationships of the aerogels, including surface area, mechanical properties, and thermal conductivity will be discussed.

  11. Covalently Cross-Linked Sulfone Polybenzimidazole Membranes with Poly(Vinylbenzyl Chloride) for Fuel Cell Applications

    DEFF Research Database (Denmark)

    Yang, Jingshuai; Aili, David; Li, Qingfeng;

    2013-01-01

    Covalently cross-linked polymer membranes were fabricated from poly(aryl sulfone benzimidazole) (SO(2) PBI) and poly(vinylbenzyl chloride) (PVBCl) as electrolytes for high-temperature proton-exchange-membrane fuel cells. The cross-linking imparted organo insolubility and chemical stability against...

  12. Self-assembly made durable: water-repellent materials formed by cross-linking fullerene derivatives.

    Science.gov (United States)

    Wang, Jiaobing; Shen, Yanfei; Kessel, Stefanie; Fernandes, Paulo; Yoshida, Kaname; Yagai, Shiki; Kurth, Dirk G; Möhwald, Helmuth; Nakanishi, Takashi

    2009-01-01

    Fullerene flakes: A diacetylene-functionalized fullerene derivative self-organizes into flakelike microparticles (see picture). Both the diacetylene and C(60) moieties can be effectively cross-linked, which leads to supramolecular materials with remarkable resistivity to solvent, heat, and mechanical stress. Moreover, the surface of the cross-linked flakelike objects is highly durable and water-repellent.

  13. Cytokines and growth factors cross-link heparan sulfate

    Science.gov (United States)

    Migliorini, Elisa; Thakar, Dhruv; Kühnle, Jens; Sadir, Rabia; Dyer, Douglas P.; Li, Yong; Sun, Changye; Volkman, Brian F.; Handel, Tracy M.; Coche-Guerente, Liliane; Fernig, David G.; Lortat-Jacob, Hugues; Richter, Ralf P.

    2015-01-01

    The glycosaminoglycan heparan sulfate (HS), present at the surface of most cells and ubiquitous in extracellular matrix, binds many soluble extracellular signalling molecules such as chemokines and growth factors, and regulates their transport and effector functions. It is, however, unknown whether upon binding HS these proteins can affect the long-range structure of HS. To test this idea, we interrogated a supramolecular model system, in which HS chains grafted to streptavidin-functionalized oligoethylene glycol monolayers or supported lipid bilayers mimic the HS-rich pericellular or extracellular matrix, with the biophysical techniques quartz crystal microbalance (QCM-D) and fluorescence recovery after photobleaching (FRAP). We were able to control and characterize the supramolecular presentation of HS chains—their local density, orientation, conformation and lateral mobility—and their interaction with proteins. The chemokine CXCL12α (or SDF-1α) rigidified the HS film, and this effect was due to protein-mediated cross-linking of HS chains. Complementary measurements with CXCL12α mutants and the CXCL12γ isoform provided insight into the molecular mechanism underlying cross-linking. Fibroblast growth factor 2 (FGF-2), which has three HS binding sites, was also found to cross-link HS, but FGF-9, which has just one binding site, did not. Based on these data, we propose that the ability to cross-link HS is a generic feature of many cytokines and growth factors, which depends on the architecture of their HS binding sites. The ability to change matrix organization and physico-chemical properties (e.g. permeability and rigidification) implies that the functions of cytokines and growth factors may not simply be confined to the activation of cognate cellular receptors. PMID:26269427

  14. Feruloylated arabinoxylans are oxidatively cross-linked by extracellular maize peroxidase but not by horseradish peroxidase.

    Science.gov (United States)

    Burr, Sally J; Fry, Stephen C

    2009-09-01

    Covalent cross-linking of soluble extracellular arabinoxylans in living maize cultures, which models the cross-linking of wall-bound arabinoxylans, is due to oxidation of feruloyl esters to oligoferuloyl esters and ethers. The oxidizing system responsible could be H2O2/peroxidase, O2/laccase, or reactive oxygen species acting non-enzymically. To distinguish these possibilities, we studied arabinoxylan cross-linking in vivo and in vitro. In living cultures, exogenous, soluble, extracellular, feruloylated [pentosyl-3H]arabinoxylans underwent cross-linking, beginning abruptly 8 d after sub-culture. Cross-linking was suppressed by iodide, an H2O2 scavenger, indicating dependence on endogenous H2O2. However, exogenous H2O2 did not cause precocious cross-linking, despite the constant presence of endogenous peroxidases, suggesting that younger cultures contained natural cross-linking inhibitors. Dialysed culture-filtrates cross-linked [3H]arabinoxylans in vitro only if H2O2 was also added, indicating a peroxidase requirement. This cross-linking was highly ionic-strength-dependent. The peroxidases responsible were heat-labile, although relatively heat-stable peroxidases (assayed on o-dianisidine) were also present. Surprisingly, added horseradish peroxidase, even after heat-denaturation, blocked the arabinoxylan-cross-linking action of maize peroxidases, suggesting that the horseradish protein was a competing substrate for [3H]arabinoxylan coupling. In conclusion, we show for the first time that cross-linking of extracellular arabinoxylan in living maize cultures is an action of apoplastic peroxidases, some of whose unusual properties we report.

  15. Feruloylated Arabinoxylans Are Oxidatively Cross-Linked by Extracellular Maize Peroxidase but Not by Horseradish Peroxidase

    Institute of Scientific and Technical Information of China (English)

    Sally J. Burr; Stephen C. Fry

    2009-01-01

    Covalent cross-linking of soluble extraceUular arabinoxylans in living maize cultures, which models the cross-linking of wall-bound arabinoxylans, is due to oxidation of feruloyl esters to oligoferuloyl esters and ethers. The oxidizing system responsible could be H_2O_2/peroxidase, O_2/laccase, or reactive oxygen species acting non-enzymically. To distinguish these possibilities, we studied arabinoxylan cross-linking in vivo and in vitro. In living cultures, exogenous, soluble, extra-cellular, feruloylated [pentosyl-~3H]arabinoxylans underwent cross-linking, beginning abruptly 8 d after sub-culture. Cross-linking was suppressed by iodide, an H_2O_2 scavenger, indicating dependence on endogenous H2O2. However, exogenous H_2O_2 did not cause precocious cross-linking, despite the constant presence of endogenous peroxidases, suggesting that younger cultures contained natural cross-linking inhibitors. Dialysed culture-filtrates cross-linked [~3H]arabinoxylans in vitro only if H_20_2 was also added, indicating a peroxiclase requirement. This cross-linking was highly ionic-strength-dependent. The peroxidases responsible were heat-labile, although relatively heat-stable peroxidases (assayed on o-dianisidine) were also present, Surprisingly, added horseradish peroxidase, even after heat-denaturation, blocked the arabinoxylan-cross-linking action of maize peroxidases, suggesting that the horseradish protein was a competing substrate for [~3H]arabino-xylan coupling. In conclusion, we show for the first time that cross-linking of extracellular arabinoxylan in living maize cultures is an action of apoplastic peroxidases, some of whose unusual properties we report.

  16. High Density Matter

    Directory of Open Access Journals (Sweden)

    Stone J.R.

    2013-12-01

    Full Text Available The microscopic composition and properties of matter at super-saturation densities have been the subject of intense investigation for decades. The scarcity of experimental and observational data has led to the necessary reliance on theoretical models. There remains great uncertainty in these models which, of necessity, have to go beyond the over-simple assumption that high density matter consists only of nucleons and leptons. Heavy strange baryons, mesons and quark matter in different forms and phases have to be included to fulfil basic requirements of fundamental laws of physics. In this contribution latest developments in construction of the Equation of State (EoS of high-density matter at zero and finite temperature assuming different composition of matter will be discussed. Critical comparison of model EoS with available experimental data from heavy ion collisions and observations on neutron stars, including gravitational mass, radii and cooling patterns and data on X-ray burst sources and low mass X-ray binaries are made. Fundamental differences between the EoS of low-density, high temperature matter, such as is created in heavy ion collisions and of high-density, low temperature compact objects is discussed.

  17. Viscoelastic Model of Cross-Linked Polyethylene Including Effects of Temperature and Crystallinity

    Science.gov (United States)

    Olasz, L.; Gudmundson, P.

    2005-12-01

    Characterization of the mechanical behavior of cross-linked polyethylene (XLPE) commonly used in high voltage cable insulation was performed by an extensive set of isothermal uniaxial tensile relaxation tests. Tensile relaxation experiments were complemented by pressure-volume-temperature experiments as well as density and crystallinity measurements. Based on the experimental results, a viscoelastic power law model with four parameters was formulated, incorporating temperature and crystallinity dependence. It was found that a master curve can be developed by both horizontal and vertical shifting of the relaxation curves. The model was evaluated by making comparisons of the predicted stress responses with the measured responses in relaxation tests with transient temperature histories.

  18. [Corneal collagen cross-linking for keratoconus].

    Science.gov (United States)

    Zotov, V V; Pashtaev, N P; Pozdeeva, N A

    2015-01-01

    Over the last decade, corneal collagen cross-linking (CXL) has become a conventional treatment method for progressive keratoconus. Laboratory studies have shown that CXL increases the diameter of collagen fibers and also the number of intra- and interfibrillar cross-links, thus, increasing biomechanical strength of the irradiated cornea. As confirmed by a series of clinical and randomized controlled trials, CXL is able to slow down and, perhaps, to stop the progression of keratoconus. In most post-CXL patients visual acuity improves, while keratometric readings, spherical equivalent, and higher order aberrations reduce. Although published results prove CXL effective in the treatment of progressive keratoconus, its late consequences are yet unknown. This article reviews the stages of CXL development and results of published experimental and clinical studies. Prospects for CXL modifications that do not require epithelial debridement are discussed.

  19. Effects of Supercritical CO 2 Conditioning on Cross-Linked Polyimide Membranes

    KAUST Repository

    Kratochvil, Adam M.

    2010-05-25

    The effects of supercritical CO2 (scCO2) conditioning on high-performance cross-linked polyimide membranes is examined through gas permeation and sorption experiments. Under supercritical conditions, the cross-linked polymers do not exhibit a structural reorganization of the polymer matrix that was observed in the non-cross-linkable, free acid polymer. Pure gas permeation isotherms and mixed gas permeabilities and selectivities show the cross-linked polymers to be much more stable to scCO2 conditioning than the free acid polymer. In fact, following scCO2 conditioning, the mixed gas CO2 permeabilities of the cross-linked polymers increased while the CO2/CH4 separation factors remained relatively unchanged. This response highlights the stability and high performance of these cross-linked membranes in aggressive environments. In addition, this response reveals the potential for the preconditioning of cross-linked polymer membranes to enhance productivity without sacrificing efficiency in practical applications which, in effect, provides another tool to \\'tune\\' membrane properties for a given separation. Finally, the dual mode model accurately describes the sorption and dilation characteristics of the cross-linked polymers. The changes in the dual mode sorption model parameters before and after the scCO2 exposure also provide insights into the alterations in the different glassy samples due to the cross-linking and scCO2 exposure. © 2010 American Chemical Society.

  20. Characterization of Cross-Linked Lipase Aggregates

    DEFF Research Database (Denmark)

    Prabhavathi Devi, Bethala Lakshmi Anu; Guo, Zheng; Xu, Xuebing

    2009-01-01

    Commercially available microbial lipases from different sources were immobilized as cross-linked enzyme aggregates (CLEAs) using different precipitants and glutaraldehyde as cross-linkers. These CLEAs were assayed based on esterification between lauric acid and n-propanol in solvent-free systems...... change upon CLEA formation. This work presents a characterization of CLEAs based on an esterification activity assay, which is useful for exploring the synthetic application potential of CLEA technology with favorable perspectives....

  1. Thermal Analyse sof Cross-Linked Polyethylene

    Directory of Open Access Journals (Sweden)

    Radek Polansky

    2007-01-01

    Full Text Available The paper summarizes results obtained during the structural analyses measurements (Differential Scanning Calorimetry DSC, Thermogravimetry TG, Thermomechanical analysis TMA and Fourier transform infrared spectroscopy FT-IR. The samples of cross-linked polyethylene cable insulation were tested via these analyses. The DSC and TG were carried out using simultaneous thermal analyzer TA Instruments SDT Q600 with connection of Fourier transform infrared spectrometer Nicolet 380. Thermomechanical analysis was carried out by TMA Q400EM TA Instruments apparatus.

  2. Permanent Set of Cross-Linking Networks: Comparison of Theory with Molecular Dynamics Simulations

    DEFF Research Database (Denmark)

    Rottach, Dana R.; Curro, John G.; Budzien, Joanne

    2006-01-01

    The permanent set of cross-linking networks is studied by molecular dynamics. The uniaxial stress for a bead-spring polymer network is investigated as a function of strain and cross-link density history, where cross-links are introduced in unstrained and strained networks. The permanent set...... is found from the strain of the network after it returns to the state-of-ease where the stress is zero. The permanent set simulations are compared with theory using the independent network hypothesis, together with the various theoretical rubber elasticity theories: affine, phantom, constrained junction...

  3. Permanent Set of Cross-Linking Networks: Comparison of Theory with Molecular Dynamics Simulations

    DEFF Research Database (Denmark)

    Rottach, Dana R.; Curro, John G.; Budzien, Joanne;

    2006-01-01

    is found from the strain of the network after it returns to the state-of-ease where the stress is zero. The permanent set simulations are compared with theory using the independent network hypothesis, together with the various theoretical rubber elasticity theories: affine, phantom, constrained junction......The permanent set of cross-linking networks is studied by molecular dynamics. The uniaxial stress for a bead-spring polymer network is investigated as a function of strain and cross-link density history, where cross-links are introduced in unstrained and strained networks. The permanent set...

  4. Collagen cross-linking in thin corneas

    Directory of Open Access Journals (Sweden)

    Prema Padmanabhan

    2013-01-01

    Full Text Available Collagen cross-linking (CXL has become the standard of care for progressive keratoconus, after numerous clinical studies have established its efficacy and safety in suitably selected eyes. The standard protocol is applicable in eyes which have a minimum corneal thickness of 400 μm after epithelial debridement. This prerequisite was stipulated to protect the corneal endothelium and intraocular tissues from the deleterious effect of ultraviolet-A (UVA radiation. However, patients with keratoconus often present with corneal thickness of less than 400 μm and could have otherwise benefited from this procedure. A few modifications of the standard procedure have been suggested to benefit these patients without a compromise in safety. Transepithelial cross-linking, pachymetry-guided epithelial debridement before cross-linking, and the use of hypoosmolar riboflavin are some of the techniques that have been attempted. Although clinical data is limited at the present time, these techniques are worth considering in patients with thin corneas. Further studies are needed to scientifically establish their efficacy and safety.

  5. Preliminary In Vitro Assessment of Stem Cell Compatibility with Cross-Linked Poly(ε-caprolactone urethane Scaffolds Designed through High Internal Phase Emulsions

    Directory of Open Access Journals (Sweden)

    Sylvie Changotade

    2015-01-01

    Full Text Available By using a high internal phase emulsion process, elastomeric poly(ε-caprolactone urethane (PCLU scaffolds were designed with pores size ranging from below 150 μm to 1800 μm and a porosity of 86% making them suitable for bone tissue engineering applications. Moreover, the pores appeared to be excellently interconnected, promoting cellularization and future bone ingrowth. This study evaluated the in vitro cytotoxicity of the PCLU scaffolds towards human mesenchymal stem cells (hMSCs through the evaluation of cell viability and metabolic activity during extract test and indirect contact test at the beginning of the scaffold lifetime. Both tests demonstrated that PCLU scaffolds did not induce any cytotoxic response. Finally, direct interaction of hMSCs and PCLU scaffolds showed that PCLU scaffolds were suitable for supporting the hMSCs adhesion and that the cells were well spread over the pore walls. We conclude that PCLU scaffolds may be a good candidate for bone tissue regeneration applications using hMSCs.

  6. Infrared microspectroscopic determination of collagen cross-links in articular cartilage

    Science.gov (United States)

    Rieppo, Lassi; Kokkonen, Harri T.; Kulmala, Katariina A. M.; Kovanen, Vuokko; Lammi, Mikko J.; Töyräs, Juha; Saarakkala, Simo

    2017-03-01

    Collagen forms an organized network in articular cartilage to give tensile stiffness to the tissue. Due to its long half-life, collagen is susceptible to cross-links caused by advanced glycation end-products. The current standard method for determination of cross-link concentrations in tissues is the destructive high-performance liquid chromatography (HPLC). The aim of this study was to analyze the cross-link concentrations nondestructively from standard unstained histological articular cartilage sections by using Fourier transform infrared (FTIR) microspectroscopy. Half of the bovine articular cartilage samples (n=27) were treated with threose to increase the collagen cross-linking while the other half (n=27) served as a control group. Partial least squares (PLS) regression with variable selection algorithms was used to predict the cross-link concentrations from the measured average FTIR spectra of the samples, and HPLC was used as the reference method for cross-link concentrations. The correlation coefficients between the PLS regression models and the biochemical reference values were r=0.84 (p<0.001), r=0.87 (p<0.001) and r=0.92 (p<0.001) for hydroxylysyl pyridinoline (HP), lysyl pyridinoline (LP), and pentosidine (Pent) cross-links, respectively. The study demonstrated that FTIR microspectroscopy is a feasible method for investigating cross-link concentrations in articular cartilage.

  7. Novel antimicrobial superporous cross-linked chitosan/pyromellitimide benzoyl thiourea hydrogels.

    Science.gov (United States)

    Mohamed, Nadia A; Abd El-Ghany, Nahed A; Fahmy, Mona M

    2016-01-01

    In this work, chitosan (CS) was cross-linked with different amounts of pyromellitimide benzoyl thiourea moieties. The structure of the cross-linked CS was confirmed by elemental analyses, FTIR and (1)H- NMR spectroscopy. The cross-linking process proceeds via reacting of the amino groups of CS with the isothiocyanate groups of the N,N'-bis [4-(isothiocyanate carbonyl)phenyl] pyromellitimide cross-linker. The amount of the cross-linker was varied with respect to CS to produce four new pyromellitimide benzoyl thiourea cross-linked CS (PIBTU-CS) hydrogels designated as PIBTU-CS-1, PIBTU-CS-2, PIBTU-CS-3, and PIBTU-CS-4 of increasing cross-linking degree percent of 11, 22, 44 and 88%, respectively. The scanning electron microscopy observation indicates the extremely porous structure of the hydrogels. XRD results showed that the crystallinity of CS was decreased upon cross-linking. The four hydrogels exhibit a higher antibacterial activity on Bacillus subtilis and Streptococcus pneumoniae as Gram positive bacteria and against Escherichia coli as Gram negative bacteria and higher antifungal activity on Aspergillus fumigatus, Syncephalastrum racemosum and Geotricum candidum than that of the parent CS as shown from their higher inhibition zone diameters and their lower MIC values. The swell ability of the hydrogel as well as their antimicrobial activity increased with increasing cross-linking density.

  8. Cross-linking for microbial keratitis

    Directory of Open Access Journals (Sweden)

    Jayesh Vazirani

    2013-01-01

    Full Text Available The success of collagen cross-linking as a clinical modality to modify the clinical course in keratoconus seems to have fueled the search for alternative applications for this treatment. Current clinical data on its efficacy is limited and laboratory data seems to indicate that it performs poorly against resistant strains of bacteria and against slow growing organisms. However, the biological plausibility of crosslinking and the lack of effective strategies in managing infections with these organisms continue to focus attention on this potential treatment. Well-conducted experimental and clinical studies with controls are required to answer the questions of its efficacy in future.

  9. A randomised controlled trial comparing highly cross-linked and contemporary annealed polyethylene after a minimal eight-year follow-up in total hip arthroplasty using cemented acetabular components.

    Science.gov (United States)

    Langlois, J; Atlan, F; Scemama, C; Courpied, J P; Hamadouche, M

    2015-11-01

    Most published randomised controlled trials which compare the rates of wear of conventional and cross-linked (XL) polyethylene (PE) in total hip arthroplasty (THA) have described their use with a cementless acetabular component. We conducted a prospective randomised study to assess the rates of penetration of two distinct types of PE in otherwise identical cemented all-PE acetabular components. A total of 100 consecutive patients for THA were randomised to receive an acetabular component which had been either highly XL then remelted or moderately XL then annealed. After a minimum of eight years follow-up, 38 hips in the XL group and 30 hips in the annealed group had complete data (mean follow-up of 9.1 years (7.6 to 10.7) and 8.7 years (7.2 to 10.2), respectively). In the XL group, the steady state rate of penetration from one year onwards was -0.0002 mm/year (sd 0.108): in the annealed group it was 0.1382 mm/year (sd 0.129) (Mann-Whitney U test, p XLPE cemented acetabular component.

  10. Riboflavin cross-linking of collagen porous scaffolds for periodontal regeneration

    Directory of Open Access Journals (Sweden)

    Seciu A-M.

    2016-05-01

    Full Text Available Periodontitis treatment using occlusive membranes presented variable efficacy due to their rapid degradation in the complex biologic environment of the damaged periodontium. The aim of this study was to prepare novel composites based on collagen, chondroitin sulfate and fibronectin, and to establish the optimal parameters for their photochemical cross-linking using riboflavin and UV exposure. The degree of cross-linking, biodegradability and density of all scaffold variants were investigated. Their cytotoxicity was evaluated in a culture of gingival fibroblasts by MTT assay and light microscopy. The results indicated that the higher the cross-linking degree, the lower was the scaffold biodegradation. Cell culture studies showed that composite scaffolds were favorable for cellular survival. In conclusion, the cross-linking method using riboflavin and UV exposure resulted in stable and biocompatible collagen-based composite scaffolds that could be used for periodontitis treatment.

  11. A novel strategy for preparing mechanically robust ionically cross-linked alginate hydrogels

    Energy Technology Data Exchange (ETDEWEB)

    Jejurikar, Aparna; Lawrie, Gwen; Groendahl, Lisbeth [School of Chemistry and Molecular Biosciences, University of Queensland, Brisbane, Queensland 4072 (Australia); Martin, Darren, E-mail: l.grondahl@uq.edu.au [Australian Institute for Bioengineering and Nanotechnology, University of Queensland, Brisbane, Queensland 4072 (Australia)

    2011-04-15

    The properties of alginate films modified using two cross-linker ions (Ca{sup 2+} and Ba{sup 2+}), comparing two separate cross-linking techniques (the traditional immersion (IM) method and a new strategy in a pressure-assisted diffusion (PD) method), are evaluated. This was achieved through measuring metal ion content, water uptake and film stability in an ionic solution ([Ca{sup 2+}] = 2 mM). Characterization of the internal structure and mechanical properties of hydrated films were established by cryogenic scanning electron microscopy and tensile testing, respectively. It was found that gels formed by the PD technique possessed greater stability and did not exhibit any delamination after 21 day immersion as compared to gels formed by the IM technique. The Ba{sup 2+} cross-linked gels possessed significantly higher cross-linking density as reflected in lower water content, a more dense internal structure and higher Young's modulus compared to Ca{sup 2+} cross-linked gels. For the Ca{sup 2+} cross-linked gels, a large improvement in the mechanical properties was observed in gels produced by the PD technique and this was attributed to thicker pore walls observed within the hydrogel structure. In contrast, for the Ba{sup 2+} cross-linked gels, the PD technique resulted in gels that had lower tensile strength and strain energy density and this was attributed to phase separation and larger macropores in this gel.

  12. High Density QCD

    CERN Document Server

    Ducati, M B G

    2001-01-01

    The dynamics of high partonic density QCD is presented considering, in the double logarithm approximation, the parton recombination mechanism built in the AGL formalism, developed including unitarity corrections for the nucleon as well for nucleus. It is shown that these corrections are under theoretical control. The resulting non linear evolution equation is solved in the asymptotic regime, and a comprehensive phenomenology concerning Deep Inelastic Scattering like $F_2$, $F_L$, $F_2^c$. $\\partial F_2/ \\partial \\ln Q^2$, $\\partial F^A_2/ \\partial \\ln Q^2$, etc, is presented. The connection of our formalism with the DGLAP and BFKL dynamics, and with other perturbative (K) and non-perturbative (MV-JKLW) approaches is analised in detail. The phenomena of saturation due to shadowing corrections and the relevance of this effect in ion physics and heavy quark production is emphasized. The implications to e-RHIC, HERA-A, and LHC physics and some open questions are mentioned.

  13. Enzymatic characterization of transglutaminase from Streptomyces mobaraensis DSM 40587 in high salt and effect of enzymatic cross-linking of yak milk proteins on functional properties of stirred yogurt.

    Science.gov (United States)

    Zhang, L; Zhang, L; Yi, H; Du, M; Ma, C; Han, X; Feng, Z; Jiao, Y; Zhang, Y

    2012-07-01

    Streptomyces transglutaminase (TGase) purified from high-salt medium was characterized and applied into yak yogurts. The purified enzyme presented a Michaelis constant of 40.47 mmol and a maximum velocity of 44.44 U/mg of protein for N-carboxybenzoyl-l-glutaminyl-glycine in the hydroxamate procedure. The purified TGase exhibited optimum activity at 55°C and pH 6.0. The enzyme was not stable above 50°C and was stable within a pH range of 5.0 to 10.0 at 4°C for 12h and pH 5.0 to 9.0 at 37°C for 30 min. The TGase activity was not affected by Ca(2+), K(+), Ba(2+), or Na(+), but slightly inhibited by Fe(2+), Mg(2+), and Mn(2+), and strongly by Cu(2+) and Zn(2+). To explore yak milk products, it was used to produce yogurt and TGase was used. It was found that TGase-catalyzed cross-linking was effective in improving functional properties of stirred yak yogurt. Treated yogurt produced a strong acid gel, higher consistency, cohesiveness, index of viscosity, and creamier mouth feel than the untreated product. Furthermore, yak yogurt treated with TGase presented lower wet yak hair or sweat odor, or both. Therefore, TGase can be used to pave the way for exploration of novel yak products to overcome the issues of peculiar wet yak hair or sweat odor, or both.

  14. Stabilized sulfonated aromatic polymers by in situ solvothermal cross-linking

    Directory of Open Access Journals (Sweden)

    Maria Luisa eDi Vona

    2014-10-01

    Full Text Available The cross-link reaction via sulfone bridges of sulfonated polyetheretherketone (SPEEK by thermal treatment at 180 °C in presence of dimethylsulfoxide (DMSO is discussed. The modifications of properties subsequent to the cross-linking are presented. The mechanical strength as well as the hydrolytic stability increased with the thermal treatment time, i.e., with the degree of cross-linking. The proton conductivity was determined as function of temperature, IEC, degree of cross-linking and hydration number. The memory effect, which is the membrane ability to remember the water uptake reached at high temperature also at lower temperature, is exploited in order to achieve high values of conductivity. Membranes swelled at 110 °C can reach a conductivity of 0.14 S/cm at 80°C with a hydration number ( of 73.

  15. Comparative study of PBI Cross Linked Utilizing Agents of Varying Steric Configurations

    DEFF Research Database (Denmark)

    Kirkebcek, Andreas; Aili, David; Li, Qingfeng;

    2016-01-01

    The high thermal and chemical stability of poly[2,2'-(m-phenylene)-5,5' bibenzimidazole] (PBI) accounts for its wise spread use in high temperature polymer electrolyte membrane fuel cells (HT- PEMFC). By doping the membrane with phosphoric acid (PA) ionic conductivity is obtained. Thus conductivity...... ionic or covalent cross linking. When considering such, little attention is devoted to explore the effect of the sterical configuration of the cross linking agent. In this contribution three different cross linking agents are utilized to evaluate how these affects final membrane properties....... is dependent on the amount of PA present within the membrane. However mechanical properties are reduced are significantly reduced due to the plasticizing effect shown by PA [1]. This effect is due to PBI chain displacement. This effect can be lessened by use of cross linking [2-4]. This can be obtained using...

  16. Use of proteinase K nonspecific digestion for selective and comprehensive identification of interpeptide cross-links: application to prion proteins.

    Science.gov (United States)

    Petrotchenko, Evgeniy V; Serpa, Jason J; Hardie, Darryl B; Berjanskii, Mark; Suriyamongkol, Bow P; Wishart, David S; Borchers, Christoph H

    2012-07-01

    Chemical cross-linking combined with mass spectrometry is a rapidly developing technique for structural proteomics. Cross-linked proteins are usually digested with trypsin to generate cross-linked peptides, which are then analyzed by mass spectrometry. The most informative cross-links, the interpeptide cross-links, are often large in size, because they consist of two peptides that are connected by a cross-linker. In addition, trypsin targets the same residues as amino-reactive cross-linkers, and cleavage will not occur at these cross-linker-modified residues. This produces high molecular weight cross-linked peptides, which complicates their mass spectrometric analysis and identification. In this paper, we examine a nonspecific protease, proteinase K, as an alternative to trypsin for cross-linking studies. Initial tests on a model peptide that was digested by proteinase K resulted in a "family" of related cross-linked peptides, all of which contained the same cross-linking sites, thus providing additional verification of the cross-linking results, as was previously noted for other post-translational modification studies. The procedure was next applied to the native (PrP(C)) and oligomeric form of prion protein (PrPβ). Using proteinase K, the affinity-purifiable CID-cleavable and isotopically coded cross-linker cyanurbiotindipropionylsuccinimide and MALDI-MS cross-links were found for all of the possible cross-linking sites. After digestion with proteinase K, we obtained a mass distribution of the cross-linked peptides that is very suitable for MALDI-MS analysis. Using this new method, we were able to detect over 60 interpeptide cross-links in the native PrP(C) and PrPβ prion protein. The set of cross-links for the native form was used as distance constraints in developing a model of the native prion protein structure, which includes the 90-124-amino acid N-terminal portion of the protein. Several cross-links were unique to each form of the prion protein, including

  17. Macrophage response to cross-linked and conventional UHMWPE.

    Science.gov (United States)

    Sethi, Rajiv K; Neavyn, Mark J; Rubash, Harry E; Shanbhag, Arun S

    2003-07-01

    To prevent wear debris-induced osteolysis and aseptic loosening, cross-linked ultra-high molecular weight polyethylene's (UHMWPE) with improved wear resistance have been developed. Hip simulator studies have demonstrated very low wear rates with these new materials leading to their widespread clinical use. However, the biocompatibility of this material is not known. We studied the macrophage response to cross-linked UHMWPE (XLPE) and compared it to conventional UHMWPE (CPE) as well as other clinically used orthopaedic materials such as titanium-alloy (TiAlV) and cobalt-chrome alloy (CoCr). Human peripheral blood monocytes and murine macrophages, as surrogates for cells mediating peri-implant inflammation, were cultured onto custom designed lipped disks fabricated from the test materials to isolate cells. Culture supernatants were collected at 24 and 48h and analyzed for cytokines such as IL-1alpha, IL-1beta, TNF-alpha and IL-6. Total RNA was extracted from adherent cells and gene expression was analyzed using qualitative RT-PCR. In both in vitro models, macrophages cultured on cross-linked and conventional polyethylene released similar levels of cytokines, which were also similar to levels on control tissue culture dishes. Macrophages cultured on TiAlV and CoCr-alloy released significantly higher levels of cytokines. Human monocytes from all donors varied in the magnitude of cytokines released when cultured on identical surfaces. The variability in individual donor responses to TiAlV and CoCr surfaces may reflect how individuals respond differently to similar stimuli and perhaps reveal a predisposed sensitivity to particular materials.

  18. Cross-link guided molecular modeling with ROSETTA.

    Directory of Open Access Journals (Sweden)

    Abdullah Kahraman

    Full Text Available Chemical cross-links identified by mass spectrometry generate distance restraints that reveal low-resolution structural information on proteins and protein complexes. The technology to reliably generate such data has become mature and robust enough to shift the focus to the question of how these distance restraints can be best integrated into molecular modeling calculations. Here, we introduce three workflows for incorporating distance restraints generated by chemical cross-linking and mass spectrometry into ROSETTA protocols for comparative and de novo modeling and protein-protein docking. We demonstrate that the cross-link validation and visualization software Xwalk facilitates successful cross-link data integration. Besides the protocols we introduce XLdb, a database of chemical cross-links from 14 different publications with 506 intra-protein and 62 inter-protein cross-links, where each cross-link can be mapped on an experimental structure from the Protein Data Bank. Finally, we demonstrate on a protein-protein docking reference data set the impact of virtual cross-links on protein docking calculations and show that an inter-protein cross-link can reduce on average the RMSD of a docking prediction by 5.0 Å. The methods and results presented here provide guidelines for the effective integration of chemical cross-link data in molecular modeling calculations and should advance the structural analysis of particularly large and transient protein complexes via hybrid structural biology methods.

  19. Glutaraldehyde vapor cross-linked nanofibrous PVA mat with in situ formed silver nanoparticles.

    Science.gov (United States)

    Destaye, Addisu Getachew; Lin, Cheng-Keng; Lee, Cheng-Kang

    2013-06-12

    Polyvinyl alcohol (PVA) nanofibrous mat can be easily prepared via electrospinning its aqueous solution. However, the obtained nanofibrous mat is instantaneously dissolved in water. Therefore, rendering the environmentally friendly nanofibrous mat water insoluble by cross-linking mechanism is of great interest. The electrospun PVA nanofibrous mat with an average fiber diameter of ca. 400 nm could be effectively cross-linked by glutaraldehyde vapor at room temperature. The cross-linking not only resulted in a water-insoluble nanofibrous mat but also generated an excess amount of unreacted aldehyde functional groups that could reduce silver salts into silver nanoparticles. The in situ formed silver nanoparticles along the fibrous surface showed excellent antimicrobial activity against Escherichia coli. The vapor cross-linked nanofibrous mat shows a high potential to be used for efficiently capturing and killing pathogenic bacteria.

  20. Synthesis and Characterisation of Novel Cross Linked Biopolyesters from Olive Oil as Eco-friendly Biodegradable Materials

    Directory of Open Access Journals (Sweden)

    J. Shakina

    2012-01-01

    Full Text Available Novel cross linked biopolyesters were synthesised from naturally available olive oil, oligomeric polytriglyceride fumarate (o-PTF was prepared by glycerolysis of the olive oil followed by condensation with maleic anhydride. The (o-PTF was characterised by spectral (FTIR, UV, NMR and physicochemical properties (specific gravity, viscosity, saponification value, iodine value. The molecular weight of o-PTF was estimated using gel permeation chromatography (GPC. The cross linked biopolyesters were prepared by treating o-PTF of olive with N-vinyl-2-pyrrolidone and vinyl acetate. The cross linked biopolyesters were evaluated for spectral properties (FT IR, cross linked density, thermal properties, mechanical properties and biodegradation. The potential antifungal and anti bacterial activities of the newly prepared biopolyesters were evaluated. The environment degradation was assessed by soil burial test. The outcome of the studies has revealed that the newly prepared cross linked biopolyesters are potential biodegradable material for various consumer application like package materials and agricultural applications.

  1. Cross Linked Metal Particles for Low Noise Bolometer Materials

    Science.gov (United States)

    2016-12-12

    SECURITY CLASSIFICATION OF: This final report summarizes WSU’s progress from 4/2/2015 to 09/30/2016 on the project, "Cross-linked Metal Particles ...2016 Final Report: Cross-linked Metal Particles for Low-noise Bolometer Materials The views, opinions and/or findings contained in this report are...peer-reviewed journals: Number of Papers published in non peer-reviewed journals: Final Report: Cross-linked Metal Particles for Low-noise Bolometer

  2. One-step electrospinning of cross-linked chitosan fibers.

    Science.gov (United States)

    Schiffman, Jessica D; Schauer, Caroline L

    2007-09-01

    Chitin is a nitrogen-rich polysaccharide that is abundant in crustaceans, mollusks, insects, and fungi and is the second most abundant organic material found in nature next to cellulose. Chitosan, the N-deacetylated derivative of chitin, is environmentally friendly, nontoxic, biodegradable, and antibacterial. Fibrous mats are typically used in industries for filter media, catalysis, and sensors. Decreasing fiber diameters within these mats causes many beneficial effects such as increased specific surface area to volume ratios. When the intrinsically beneficial effects of chitosan are combined with the enhanced properties of nanofibrous mats, applications arise in a wide range of fields, including medical, packaging, agricultural, and automotive. This is particularly important as innovative technologies that focus around bio-based materials are currently of high urgency, as they can decrease dependencies on fossil fuels. We have demonstrated that Schiff base cross-linked chitosan fibrous mats can be produced utilizing a one-step electrospinning process that is 25 times faster and, therefore, more economical than a previously reported two-step vapor-cross-linking method. These fibrous mats are insoluble in acidic, basic, and aqueous solutions for 72 h. Additionally, this improved production method results in a decreased average fiber diameter, which measures 128 +/- 40 nm. Chemical and structural analyses were conducted utilizing Fourier transform infrared spectroscopy, solubility studies, and scanning electron microscopy.

  3. Characterization of the receptor for endothelial cell growth factor (ECGF) by affinity cross-linking

    Energy Technology Data Exchange (ETDEWEB)

    Friesel, R.; Burgess, W.H.; Mehlman, T.; Maciag, T.

    1986-05-01

    The authors have demonstrated high affinity receptors for ECGF on endothelial cells by covalent cross-linking of (/sup 125/I)-ECGF with disuccinimidyl suberate and observe a single chain cross-linked polypeptide species with an apparent M/sub r/ of 170K. The M/sub r/ 170K species represents (/sup 125/I)-ECGF bound to its receptor since (i) excess unlabeled ECGF inhibits the cross-linking of (/sup 125/I)-ECGF, (ii) labeling of the M/sub r/170K species does not take place in the absence of cross-linker, (iii) cells previously shown to be refractory to ECGF and lack ECGF receptors do not yield a cross-linked species, (iv) the cross-linked species can be immunoprecipitated with anti-ECGF antibodies, and (v) preincubation of cells with ECGF at 37/sup 0/C significantly reduces cross-linking while incubation at 4/sup 0/C does not. These data demonstrate that ECGF induced cell proliferation occurs through the occupancy of a specific cell surface polypeptide receptor with an apparent M/sub r/ of 150K, and suggests that internalization of the receptor-ligand complex may be relevant to ECGF-induced signal transduction.

  4. Directing the oligomer size distribution of peroxidase-mediated cross-linked bovine alpha-lactalbumin.

    Science.gov (United States)

    Heijnis, Walter H; Wierenga, Peter A; van Berkel, Willem J H; Gruppen, Harry

    2010-05-12

    Enzymatic protein cross-linking is a powerful tool to change protein functionality. For optimal functionality in gel formation, the size of the cross-linked proteins needs to be controlled, prior to heating. In the current study, we addressed the optimization of the horseradish peroxidase-mediated cross-linking of calcium-depleted bovine alpha-lactalbumin. To characterize the formed products, the molecular weight distribution of the cross-linked protein was determined by size exclusion chromatography. At low ionic strength, more dimers of alpha-lactalbumin are formed than at high ionic strength, while the same conversion of monomers is observed. Similarly, at pH 5.9 more higher oligomers are formed than at pH 6.8. This is proposed to be caused by local changes in apo alpha-lactalbumin conformation as indicated by circular dichroism spectroscopy. A gradual supply of hydrogen peroxide improves the yield of cross-linked products and increases the proportion of higher oligomers. In conclusion, this study shows that the size distribution of peroxidase-mediated cross-linked alpha-lactalbumin can be directed toward the protein oligomers desired.

  5. Cross-linking proteins by laccase-catalyzed oxidation: importance relative to other modifications.

    Science.gov (United States)

    Steffensen, Charlotte L; Andersen, Mogens L; Degn, Peter E; Nielsen, Jacob H

    2008-12-24

    Laccase-catalyzed oxidation was able to induce intermolecular cross-links in beta-lactoglobulin, and ferulic acid-mediated laccase-catalyzed oxidation was able to induce intermolecular cross-links in alpha-casein, whereas transglutaminase cross-linked only alpha-casein. In addition, different patterns of laccase-induced oxidative modifications were detected, including dityrosine formation, formation of fluorescent tryptophan oxidation products, and carbonyls derived from histidine, tryptophan, and methionine. Laccase-catalyzed oxidation as well as transglutaminase induced only minor changes in surface tension of the proteins, and the changes could not be correlated to protein cross-linking. The presence of ferulic acid was found to influence the effect of laccase, allowing laccase to form irreducible intermolecular cross-links in beta-lactoglobulin and resulting in proteins exercising higher surface tensions due to cross-linking as well as other oxidative modifications. The outcome of using ferulic acid-mediated laccase-catalyzed oxidation to modify the functional properties of proteinaceous food components or other biosystems is expected to be highly dependent on the protein composition, resulting in different changes of the functional properties.

  6. Cross-linked chitosan improves the mechanical properties of calcium phosphate-chitosan cement.

    Science.gov (United States)

    Aryaei, Ashkan; Liu, Jason; Jayatissa, Ahalapitiya H; Jayasuriya, A Champa

    2015-09-01

    Calcium phosphate (CaP) cements are highly applicable and valuable materials for filling bone defects by minimally invasive procedures. The chitosan (CS) biopolymer is also considered as one of the promising biomaterial candidates in bone tissue engineering. In the present study, some key features of CaP-CS were significantly improved by developing a novel CaP-CS composite. For this purpose, CS was the first cross-linked with tripolyphosphate (TPP) and then mixed with CaP matrix. A group of CaP-CS samples without cross-linking was also prepared. Samples were fabricated and tested based on the known standards. Additionally, the effect of different powder (P) to liquid (L) ratios was also investigated. Both cross-linked and uncross-linked CaP-CS samples showed excellent washout resistance. The most significant effects were observed on Young's modulus and compressive strength in wet condition as well as surface hardness. In dry conditions, the Young's modulus of cross-linked samples was slightly improved. Based on the presented results, cross-linking does not have a significant effect on porosity. As expected, by increasing the P/L ratio of a sample, ductility and injectability were decreased. However, in the most cases, mechanical properties were enhanced. The results have shown that cross-linking can improve the mechanical properties of CaP-CS and hence it can be used for bone tissue engineering applications.

  7. Digestibility of β-lactoglobulin following cross-linking by Trametes versicolor laccase and apple polyphenols

    Directory of Open Access Journals (Sweden)

    DRAGANA STANIĆ-VUČINIĆ

    2011-06-01

    Full Text Available β-Lactoglobulin (BLG is an important nutrient of dairy products and an important allergen in cow’s milk allergy. The aim of this study was to investigate the potential of laccase to cross-link BLG in the presence of an apple phenolic extract (APE and to characterize the obtained products for their digestibility by pepsin and pancreatin. The composition of the apple phenolics used for cross-linking was determined by liquid chromatography–electrospray ionization-mass spectrometry (LC–ESI-MS. The apple phenolic extract contained significant amounts of quercetin glycosides, catechins and chlorogenic acid. The laccase cross-linked BLG in the presence of apple phenolics. The polymerization rendered the protein insoluble in the reaction mixture. Sodium dodecyl sulfate–polyacrylamide gel electrophoresis (SDS-PAGE analysis of the cross-linking reaction mixture revealed a heterogeneous mixture of high molecular masses (cross-linked BLG, with a fraction of the BLG remaining monomeric. Enzymatic processing of BLG by laccase and apple polyphenols as mediators can decrease the biphasal pepsin–pancreatin digestibility of the monomeric and cross-linked protein, thus decreasing its nutritional value. In addition, reduced BLG digestibility can decrease its allergenic potential. Apple polyphenols can find usage in the creation of new, more functional food products, designed to prevent obesity and hypersensitivity-related disorders.

  8. Characterization of the somatogenic receptor in rat liver. Hydrodynamic properties and affinity cross-linking

    Energy Technology Data Exchange (ETDEWEB)

    Husman, B.; Haldosen, L.A.; Andersson, G.; Gustafsson, J.A.

    1988-03-15

    Rat liver somatogenic receptors have been characterized by gel permeation chromatography, sucrose density gradients in H/sub 2/O and D/sub 2/O, and affinity cross-linking using /sup 125/I-bovine growth hormone (bGH) as a specific somatogenic receptor ligand. Cross-linking of /sup 125/I-bovine growth hormone to a Triton X-100-treated low density fraction isolated from livers of late pregnant rats followed by sodium dodecylsulfate-polyacrylamide gel electrophoresis under reducing conditions showed three major binders with Mr 95,000, 86,000, and 43,000 and a minor binder of Mr 55,000, after correction for bound ligand assuming a 1:1 binding ratio of ligand-receptor. The Mr 86,000, 55,000, and 43,000 species were recovered in the detergent-soluble supernatant after high-speed centrifugation, whereas the Mr 95,000 species remained Triton X-100 insoluble. Detergent-soluble /sup 125/I-bGH-receptor complexes were further analyzed by sedimentation into sucrose density gradients. The sedimentation coefficient was S20,w = 5.2 S and the partial specific volume v = 0.72 ml/g. Gel permeation chromatography on a Sepharose S-400 column indicated a Stokes radius of 61 A for the /sup 125/I-bGH-receptor-Triton X-100 complex. Based on these figures, the molecular weight of the complex was calculated as 131,100. The molecular weight of the ligand-free receptor-Triton X-100 complex was calculated as Mr 109,100. Affinity cross-linking and sodium dodecyl sulfate-polyacrylamide gel electrophoresis of the 61 A peak from Sephacryl S-400 chromatography (cf. above) showed two binding entities, one major and one minor with Mr values 86,000 and 43,000, respectively, in the absence of reductant. When electrophoresis was run in the presence of reductant the Mr 43,000 species was the major binding entity.

  9. Corneal crossed links: a new alternative in the treatment of ectasia

    Directory of Open Access Journals (Sweden)

    Maygret Alberro Hernández

    2009-09-01

    Full Text Available Cross-linking a technique that allows increasing the creation of covalent links through the process of photo-oxidation among the collagen fibers and enhance the corneal biomechanical stabilization. The main objective of this procedure is to stop the development of ectasia. The indications include the Keratoconus and Pellucid Marginal Degeneration. This can reduce the necessity for permanent keratoplasty and is highly efficient in the treatment and prophylaxis of keratectasia after ablation caused by laser. Many reviewed articles prove the security and efficacy of this treatment. The confocal microscopy techniques have shown significant swelling and resistance of corneal stroma after this procedure. Density of endothelial cell and transparency of the cornea and crystallin remain unchanged. This is a simple, safe and non-invasive technique with promising results. Since this is not expensive it could be particularly useful in developing countries where corneal transplant and other procedures are very expensive.

  10. Supercritical CO2 Foaming of Radiation Cross-Linked Isotactic Polypropylene in the Presence of TAIC

    Directory of Open Access Journals (Sweden)

    Chen-Guang Yang

    2016-12-01

    Full Text Available Since the maximum foaming temperature window is only about 4 °C for supercritical CO2 (scCO2 foaming of pristine polypropylene, it is important to raise the melt strength of polypropylene in order to more easily achieve scCO2 foaming. In this work, radiation cross-linked isotactic polypropylene, assisted by the addition of a polyfunctional monomer (triallylisocyanurate, TAIC, was employed in the scCO2 foaming process in order to understand the benefits of radiation cross-linking. Due to significantly enhanced melt strength and the decreased degree of crystallinity caused by cross-linking, the scCO2 foaming behavior of polypropylene was dramatically changed. The cell size distribution, cell diameter, cell density, volume expansion ratio, and foaming rate of radiation-cross-linked polypropylene under different foaming conditions were analyzed and compared. It was found that radiation cross-linking favors the foamability and formation of well-defined cell structures. The optimal absorbed dose with the addition of 2 wt % TAIC was 30 kGy. Additionally, the foaming temperature window was expanded to about 8 °C, making the handling of scCO2 foaming of isotactic polypropylene much easier.

  11. Increasing Thermal Stability of Gelatin by UV-Induced Cross-Linking with Glucose

    Directory of Open Access Journals (Sweden)

    Evan M. Masutani

    2014-01-01

    Full Text Available The effects of ultraviolet (254 nm radiation on a hydrated gelatin-glucose matrix were investigated for the development of a physiologically thermostable substrate for potential use in cell scaffold production. Experiments conducted with a differential scanning calorimeter indicate that ultraviolet irradiation of gelatin-glucose hydrogels dramatically increases thermal stability such that no melting is observed at temperatures of at least 90°C. The addition of glucose significantly increases the yield of cross-linked product, suggesting that glucose has a role in cross-link formation. Comparisons of lyophilized samples using scanning electron microscopy show that irradiated materials have visibly different densities.

  12. Radiation cross-linked polyolefin-insulated wire

    Science.gov (United States)

    Sano, K.; Ishitani, H.

    Because radiation cross-linked polyolefin has excellent mechanical heat resistance, its application limit can be expanded extremely by improving the resistance against heat oxidation and flame. This paper is concerning a halogen free radiation cross-linked polyolefin-insulated wire having excellent heat resistance and flameretardant property, which is used for appliances.

  13. Study and application of conformance control or water shutoff agent with delayed cross-linking and high strength%缓凝高强度调堵剂的研制与应用

    Institute of Scientific and Technical Information of China (English)

    汤元春; 崔永亮; 钱志鸿; 马惠; 邓秀模; 朱伟民

    2014-01-01

    There are high injection pressure ,big PI value of injection wells ,and serious channeling between oil and wa-ter wells in some special reservoirs .In these reservoirs ,the common type of particle plugging agent can pollute or not be in-jected into the reservoirs ,and the gel plugging agent can not plug water channels because of lower strength .Thus,two new types of plugging agents with delayed cross -linking and high strength ,respectively called DHG -1 and HHG-1,were developed ,which consis of acrylamide and polyacrylamide .Under the condition of 70℃,the initial gel times were extended from several hours to more than 5 days,and the final strengths were respectively 3.8 ×104 mPa· s and 1.4 ×104 mPa· s for the two systems .The lab experiments indicated that the blocking rates of the two plugging agents were more than 95%,and the plugging agent can have priority in entering the high permeability layer by controlling the injection rate ,and the techni-cal parameters can meet the needs of the special reservoirs .These two systems had been applied alone or compositely in 5 wells such as W5-8 well .The success rate of measures was 100%,and had a cumulative incremental oil of 1 992.3 tons.%一些特殊性油藏注水井由于注水压力高,PI值高,油水井间窜流严重,目前常用的颗粒型堵剂注不进或污染油层,凝胶型强度低堵不住水道。以丙烯酰胺、聚丙烯酰胺为主剂,研制出DHG-1和HHG-1两种新型缓凝高强度调堵剂。在70℃条件下,两种堵剂初始成胶时间由几小时延长至5 d以上,终凝强度分别达到3.8×104 mPa· s和1.2×104 mPa· s。室内堵塞率均大于95%,通过控制注入速度,堵剂可优先进入高渗目的层,各项技术参数可满足特殊性油藏调堵的需要。两种体系单独或复合应用于韦5-8等4口井的调堵试验,措施成功率100%,已累计增油1992.3 t。

  14. Simulation and theory of self-assembly and network formation in reversibly cross-linked equilibrium polymers

    Science.gov (United States)

    Kindt, James T.

    2005-10-01

    A simulation model of hard spheres capable of reversible assembly into chains, which then may reversibly cross-link into networks, has been studied through grand canonical Monte Carlo simulation. Effects of varying intra- and interchain bond strengths, chain flexibilities, and restrictions on cross-linking angle were investigated. Observations including chain-length distributions and phase separation could be captured in most cases using a simple model theory. The coupling of chain growth to cross-linking was shown to be highly sensitive to the treatment of cross-linking by chain ends. In some systems, ladderlike domains of several cross-links joining two chains were common, resulting from cooperativity in the cross-linking. Extended to account for this phenomenon, the model theory predicts that such cooperativity will suppress phase separation in weakly polymerizing chains and at high cross-link concentration. In the present model, cross-linking stabilizes the isotropic phase with respect to the nematic phase, causing a shift in the isotropic-nematic transition to higher monomer concentration than in simple equilibrium polymers.

  15. Research Progress in Corneal Cross-linking Agents

    Institute of Scientific and Technical Information of China (English)

    Na Li; Xiujun Peng; Zhengjun Fan

    2014-01-01

    Corneal collagen cross-linking with UVA-riboflavin is cur-rently the only method for preventing the progression of kera-toconus from the pathological perspective. Topical application of a direct cross-linking agent is now attracting widespread at-tention in clinical settings..This article reviews the research progress in the application of indirect or direct cross-linking agents (e.g., riboflavin, glucose, ribose, glutaraldehyde, formaldehyde,.glyceraldehyde,.short chain aliphatic β-nitro alcohol, and genipin) in the treatment of corneal diseases and analyzes the cross-linking efficacy,.toxicity,.and merits and disadvantages of each cross-linking agent,.providing clinical information for further studies.

  16. High density photovoltaic

    Energy Technology Data Exchange (ETDEWEB)

    Haigh, R.E.; Jacobson, G.F.; Wojtczuk, S. [Spire Corp., Bedford, MA (United States)

    1997-10-14

    Photovoltaic technology can directly generate high voltages in a solid state material through the series interconnect of many photovoltaic diodes. We are investigating the feasibility of developing an electrically isolated, high-voltage power supply using miniature photovoltaic devices that convert optical energy to electrical energy.

  17. Cross-linked hyaluronic acid in pressure ulcer prevention.

    Science.gov (United States)

    Beniamino, P; Vadalà, M; Laurino, C

    2016-07-02

    Long-term bedridden patients are at high risk of acquring pressure ulcers (PUs). In this group of patients, prevention is necessary to cut the health costs, improve quality of life and reduce the mortality. Here, we evaluated the effectiveness of a cross-linked hyaluronic acid (HA) as plastic bulking-agent filling and remodelling the deep dermis and subcutaneous space of the skin areas exposed to the risk of necrosis. Our work hypothesis has been to inflate a sub-dermal elastic cushion, filled with a natural ECM component, with the aim to induce a stronger tissue background resistant to the ulcerative process. All the patients had an increased risk of PUs, at the sacral, ileum or heel skin. Patients were being nursed accordingly to the standard orthopaedic ward management with a pressure relieveing air mattress. The standard protocol consisted in body mobilisation every 3 hours, 24 hours a day and accurate cleaning of the skin with liquid soap and water without any towel friction and without adding any cream or lotion for the skin protection. Our filling protocol enclosed: accurate disinfection of the skin to be injected with povidone-iodine solution, followed by a local anaesthesia with 28G 13 mm needle, injecting 1.5 ml of 1% xylocaine. Then slow, deep, subcutaneous injection of cross-linked HA was performed with a 18G long needle, in order to deliver a homogeneous, soft gel layer underneath and around the whitish erythematous skin edges at risk of ulceration. Patients' tolerability of the compound and adverse events were also recorded. There were 15 patients (78-94 years old) who participated in the study. All tolerated the procedure very well and no serious side effects were declared. No skin pressure ulceration was detected in the four weeks follow-up Conclusion: We have demonstrated the safety and tolerability of a cross-linked HA subdermal injection in PUs prevention. The compound stratifies in a soft, elastic, interstitial bulk into the deep dermis, thus

  18. Polymer-additive extraction via pressurized fluids and organic solvents of variously cross-linked poly(methylmethacrylates).

    Science.gov (United States)

    Nazem, N; Taylor, L T

    2002-04-01

    Variously cross-linked poly(methylmethacrylates) (PMMAs) are synthesized with three additives incorporated at theoretically 1000 microg of the additive per gram of prepared polymer. The additives are Irganox 1010, Irganox 1076, and Irgafos 168. The in-house" synthesized polyacrylates are then subjected to supercritical fluid extraction (SFE) to determine if additive recovery is a function of percent cross-linking. Although considerable work in this regard has been performed with non-cross-linked polyolefins, the literature is lacking regarding polyacrylates. Some additive degradation apparently occurs during the synthesis, as judged by the increased complexity of the extract high-performance liquid chromatographic trace and the low percent recoveries observed especially for the Irganoxes. For low polymer cross-linking (1%), it appears that both PMMA synthetic reproducibility and readily observed polymer swelling during SFE are serious issues that adversely affect additive percent recovery and precision of results. Higher percent cross-linking yields more consistent analytical data than low percent cross-linking, even though the amount of additive extracted in all PMMA samples (regardless of cross-linking percentage) is essentially the same whether the extraction is via SFE or liquid-solid extraction with methylene chloride. Results for comparably cross-linked poly(ethylmethacrylate) and poly(butylmethacrylate) are similar to PMMA.

  19. Dehydration of an ethanol/water azeotrope through alginate-DNA membranes cross-linked with metal ions by pervaporation.

    Science.gov (United States)

    Uragami, Tadashi; Banno, Masashi; Miyata, Takashi

    2015-12-10

    To obtain high dehydration membranes for an ethanol/water azeotrope, dried blend membranes prepared from mixtures of sodium alginate (Alg-Na) and sodium deoxyribonucleate (DNA-Na) were cross-linked by immersing in a methanol solution of CaCl2 or MaCl2. In the dehydration of an ethanol/water azeotropic mixture by pervaporation, the effects of immersion time in methanol solution of CaCl2 or MaCl2 on the permeation rate and water/ethanol selectivity through Alg-DNA/Ca(2+) and Alg-DNA/Mg(2+) cross-linked membranes were investigated. Alg-DNA/Mg(2+) cross-linked membrane immersed for 12h in methanol solution of MaCl2 exhibited the highest water/ethanol selectivity. This results from depressed swelling of the membranes by formation of a cross-linked structure. However, excess immersion in solution containing cross-linker led to an increase in the hydrophobicity of cross-linked membrane. Therefore, the water/ethanol selectivity of Alg-DNA/Mg(2+) cross-linked membranes with an excess immersion in cross-linking solution was lowered. The relationship between the structure of Alg-DNA/Ca(2+) and Alg-DNA/Mg(2+) cross-linked membranes and their permeation and separation characteristics during pervaporation of an ethanol/water azeotropic mixture is discussed in detail.

  20. Synthesis and Characterization of Poly(maleic Anhydride)s Cross-linked Polyimide Aerogels

    Science.gov (United States)

    Guo, Haiquan; Meador, Mary Ann B.

    2015-01-01

    With the development of technology for aerospace applications, new thermal insulation materials are required to be flexible and capable of surviving high heat flux. For instance, flexible insulation is needed for inflatable aerodynamic decelerators which are used to slow spacecraft for entry, descent and landing (EDL) operations. Polyimide aerogels have low density, high porosity, high surface area, and better mechanical properties than silica aerogels and can be made into flexible thin films, thus they are potential candidates for aerospace needs. The previously reported cross-linkers such as octa(aminophenyl)silsesquioxane (OAPS) and 1,3,5-triaminophenoxybenzene (TAB) are either expensive or not commercially available. Here, we report the synthesis of a series of polyimide aerogels cross-linked using various commercially available poly(maleic anhydride)s, as seen in Figure 1. The amine end capped polyimide oligomers were made with 3,3,4,4-biphenyltetracarboxylic dianhydride (BPDA) and diamine combinations of dimethylbenzidine (DMBZ) and 4, 4-oxydianiline (ODA). The resulting aerogels have low density (0.12 gcm3 to 0.16 gcm3), high porosity (90) and high surface area (380-554 m2g). The effect of the different poly(maleic anhydride) cross-linkers and polyimide backbone structures on density, shrinkage, porosity, surface area, mechanical properties, moisture resistance and thermal properties will be discussed.

  1. Cross-linking study on skeletal muscle actin: properties of suberimidate-treated actin.

    Science.gov (United States)

    Ohara, O; Takahashi, S; Ooi, T; Fujiyoshi, Y

    1982-06-01

    Cross-linking experiments were performed on muscle skeletal actin, using imidoesters of various chain lengths. Chemical analyses on all products except one (derived from succinimidate) show evidence of the presence of intramolecular cross-links in the molecule. The detailed properties of suberimidate-treated actin (SA) are as follows: SA contains nearly 1 mol of intramolecular cross-link per mol of actin and less than 15% of intermolecularly cross-linked products. Even at a low salt concentration, SA is polymeric, exchanges slowly its bound nucleotide with free nucleotides in solution, and shows an F-actin-type CD spectrum. Electron micrographs of SA reveal that SA exists actually as fibrous polymers in solutions of low ionic strength, although the fibers seem to be less rigid than those at high salt concentration. The F-form of SA at a high salt concentration is indistinguishable from intact F-actin. SA can bind heavy meromyosin and activate the ATPase of heavy meromyosin as observed for intact F-actin. Tropomyosin binds SA only at a high salt concentration. These results show that SA possesses the properties of F-actin even in media of low salt concentration, which are favorable for depolymerization of F-actin. Thus, we may infer that the conformation of SA is frozen in the F-state of actin by the introduction of intramolecular cross-links in the protein.

  2. High Energy Density Capacitors Project

    Data.gov (United States)

    National Aeronautics and Space Administration — NASA?s future space science missions cannot be realized without the state of the art energy storage devices which require high energy density, high reliability, and...

  3. Elasticity of cross-linked semiflexible biopolymers under tension.

    Science.gov (United States)

    von der Heydt, Alice; Wilkin, Daniel; Benetatos, Panayotis; Zippelius, Annette

    2013-09-01

    Aiming at the mechanical properties of cross-linked biopolymers, we set up and analyze a model of two weakly bending wormlike chains subjected to a tensile force, with regularly spaced inter-chain bonds (cross-links) represented by harmonic springs. Within this model, we compute the force-extension curve and the differential stiffness exactly and discuss several limiting cases. Cross-links effectively stiffen the chain pair by reducing thermal fluctuations transverse to the force and alignment direction. The extra alignment due to cross-links increases both with growing number and with growing strength of the cross-links, and is most prominent for small force f. For large f, the additional, cross-link-induced extension is subdominant except for the case of linking the chains rigidly and continuously along their contour. In this combined limit, we recover asymptotically the elasticity of a weakly bending wormlike chain without constraints, stiffened by a factor of 4. The increase in differential stiffness can be as large as 100% for small f or large numbers of cross-links.

  4. The wear of cross-linked polyethylene against itself.

    Science.gov (United States)

    Joyce, T J; Ash, H E; Unsworth, A

    1996-01-01

    Cross-linked polyethylene (XLPE) may have an application as a material for an all-plastic surface replacement finger joint. It is inexpensive, biocompatible and can be injection-moulded into the complex shapes that are found on the ends of the finger bones. Further, the cross-linking of polyethylene has significantly improved its mechanical properties. Therefore, the opportunity exists for an all-XLPE joint, and so the wear characteristics of XLPE sliding against itself have been investigated. Wear tests were carried out on both reciprocating pin-on-plate machines and a finger function simulator. The reciprocating pin-on-plate machines had pins loaded at 10 N and 40 N. All pin-on-plate tests show wear factors from the plates very much greater than those of the pins. After 349 km of sliding, a mean wear factor of 0.46 x 10(-6) mm3/N m was found for the plates compared with 0.021 x 10(-6) mm3/N m for the pins. A fatigue mechanism may be causing this phenomenon of greater plate wear. Tests using the finger function simulator give an average wear rate of 0.22 x 10(-6) mm3/N m after 368 km. This sliding distance is equivalent to 12.5 years of use in vivo. The wear factors found were comparable with those of ultra-high molecular weight polyethylene (UHMWPE) against a metallic counterface and, therefore, as the loads across the finger joint are much less than those across the knee or the hip, it is probable that an all-XLPE finger joint will be viable from a wear point of view.

  5. Molecular Structures of Isolevuglandin-Protein Cross-Links.

    Science.gov (United States)

    Bi, Wenzhao; Jang, Geeng-Fu; Zhang, Lei; Crabb, John W; Laird, James; Linetsky, Mikhail; Salomon, Robert G

    2016-10-17

    Isolevuglandins (isoLGs) are stereo and structurally isomeric γ-ketoaldehydes produced through free radical-induced oxidation of arachidonates. Some isoLG isomers are also generated through enzymatic cyclooxygenation. Post-translational modification of proteins by isoLGs is associated with loss-of-function, cross-linking and aggregation. We now report that a low level of modification by one or two molecules of isoLG has a profound effect on the activity of a multi subunit protease, calpain-1. Modification of one or two key lysyl residues apparently suffices to abolish catalytic activity. Covalent modification of calpain-1 led to intersubunit cross-linking. Hetero- and homo-oligomers of the catalytic and regulatory subunits of calpain-1 were detected by SDS-PAGE with Western blotting. N-Acetyl-glycyl-lysine methyl ester and β-amyloid(11-17) peptide EVHHQKL were used as models for characterizing the cross-linking of protein lysyl residues resulting from adduction of iso[4]LGE2. Aminal, bispyrrole, and trispyrrole cross-links of these two peptides were identified and fully characterized by mass spectrometry. Aminal and bispyrrole dimers were both detected. Furthermore, a complex mixture of derivatives of the bispyrrole cross-link containing one or more additional atoms of oxygen was found. Interesting differences are evident in the predominant cross-link type generated in the reaction of iso[4]LGE2 with these peptides. More aminal cross-links versus bispyrrole are formed during the reaction of the dipeptide with iso[4]LGE2. In contrast, more bispyrrole versus aminal cross-links are formed during the reaction of EVHHQKL with iso[4]LGE2. It is tempting to speculate that the EVHHQKL peptide-pyrrole modification forms noncovalent aggregates that favor the production of covalent bispyrrole cross-links because β-amyloid(11-17) tends to spontaneously oligomerize.

  6. Current status of accelerated corneal cross-linking

    Directory of Open Access Journals (Sweden)

    Michael Mrochen

    2013-01-01

    Full Text Available Corneal cross-linking with riboflavin is a technique to stabilize or reduce corneal ectasia, in diseases such as keratoconus and post-laser-assisted in situ keratomileusis (LASIK ectasia. There is an interest by patient as well as clinicians to reduce the overall treatment time. Especially, the introduction of corneal cross-linking in combination with corneal laser surgery demands a shorter treatment time to assure a sufficient patient flow. The principles and techniques of accelerated corneal cross-linking is discussed.

  7. Effects of partial hydrolysis and subsequent cross-linking on wheat gluten physicochemical properties and structure.

    Science.gov (United States)

    Wang, Kaiqiang; Luo, Shuizhong; Cai, Jing; Sun, Qiaoqiao; Zhao, Yanyan; Zhong, Xiyang; Jiang, Shaotong; Zheng, Zhi

    2016-04-15

    The rheological behavior and thermal properties of wheat gluten following partial hydrolysis using Alcalase and subsequent microbial transglutaminase (MTGase) cross-linking were investigated. The wheat gluten storage modulus (G') and thermal denaturation temperature (Tg) were significantly increased from 2.26 kPa and 54.43°C to 7.76 kPa and 57.69°C, respectively, by the combined action of partial hydrolysis (DH 0.187%) and cross-linking. The free SH content, surface hydrophobicity, and secondary structure analysis suggested that an appropriate degree of Alcalase-based hydrolysis allowed the compact wheat gluten structure to unfold, increasing the β-sheet content and surface hydrophobicity. This improved its molecular flexibility and exposed additional glutamine sites for MTGase cross-linking. SEM images showed that a compact 3D network formed, while SDS-PAGE profiles revealed that excessive hydrolysis resulted in high-molecular-weight subunits degrading to smaller peptides, unsuitable for cross-linking. It was also demonstrated that the combination of Alcalase-based partial hydrolysis with MTGase cross-linking might be an effective method for modifying wheat gluten rheological behavior and thermal properties.

  8. Synthesis, Characterization, and Antibacterial Activity of Cross-Linked Chitosan-Glutaraldehyde

    Directory of Open Access Journals (Sweden)

    Long-Biao Guo

    2013-05-01

    Full Text Available This present study deals with synthesis, characterization and antibacterial activity of cross-linked chitosan-glutaraldehyde. Results from this study indicated that cross-linked chitosan-glutaraldehyde markedly inhibited the growth of antibiotic-resistant Burkholderia cepacia complex regardless of bacterial species and incubation time while bacterial growth was unaffected by solid chitosan. Furthermore, high temperature treated cross-linked chitosan-glutaraldehyde showed strong antibacterial activity against the selected strain 0901 although the inhibitory effects varied with different temperatures. In addition, physical-chemical and structural characterization revealed that the cross-linking of chitosan with glutaraldehyde resulted in a rougher surface morphology, a characteristic Fourier transform infrared (FTIR band at 1559 cm−1, a specific X-ray diffraction peak centered at 2θ = 15°, a lower contents of carbon, hydrogen and nitrogen, and a higher stability of glucose units compared to chitosan based on scanning electron microscopic observation, FTIR spectra, X-ray diffraction pattern, as well as elemental and thermo gravimetric analysis. Overall, this study indicated that cross-linked chitosan-glutaraldehyde is promising to be developed as a new antibacterial drug.

  9. Cross-Linking Poly(lactic acid) Film Surface by Neutral Hyperthermal Hydrogen Molecule Bombardment.

    Science.gov (United States)

    Du, Wangli; Shao, Hong; He, Zhoukun; Tang, Changyu; Liu, Yu; Shen, Tao; Zhu, Yan; Lau, Woon-ming; Hui, David

    2015-12-16

    Constructing a dense cross-linking layer on a polymer film surface is a good way to improve the water resistance of poly(lactic acid) (PLA). However, conventional plasma treatments have failed to achieve the aim as a result of the unavoidable surface damage arising from the charged species caused by the uncontrolled high energy coming from colliding ions and electrons. In this work, we report a modified plasma method called hyperthermal hydrogen-induced cross-linking (HHIC) technology to construct a dense cross-linking layer on PLA film surfaces. This method produces energy-controlled neutral hyperthermal hydrogen, which selectively cleaves C-H bonds by molecule collision from the PLA film without breaking other bonds (e.g., C-C bonds in the polymer backbone), and results in subsequent cross-linking of the carbon radicals generated from the organic molecules. The formation of a dense cross-linking layer can serve as a barrier layer to significantly improve both the hydrophobicity and water vapor barrier property of the PLA film. Because of the advantage of selective cleavage of C-H bonds by HHIC treatment, the original physical properties (e.g., mechanical strength and light transmittance) of the PLA films are well-preserved.

  10. Design and Preparation of Cross-Linked Polystyrene Nanoparticles for Elastomer Reinforcement

    Directory of Open Access Journals (Sweden)

    Ming Lu

    2010-01-01

    Full Text Available Cross-linked polystyrene (PS particles in a latex form were synthesized by free radical emulsion polymerization. The nano-PS-filled elastomer composites were prepared by the energy-saving latex compounding method. Results showed that the PS particles took a spherical shape in the size of 40–60 nm with a narrow size distribution, and the glass-transition temperature of the PS nanoparticles increased with the cross-linking density. The outcomes from the mechanical properties demonstrated that when filled into styrene-butadiene rubber (SBR, nitrile-butadiene rubber (NBR, and natural rubber (NR, the cross-linked PS nano-particles exhibited excellent reinforcing capabilities in all the three matrices, and the best in the SBR matrix. In comparison with that of the carbon black filled composites, another distinguished advantage of the cross-linked PS particles filled elastomer composites was found to be light weight in density, which could help to save tremendous amount of energy when put into end products.

  11. Improvement on Physical Properties of Pullulan Films by Novel Cross-Linking Strategy.

    Science.gov (United States)

    Chen, Chieh-Ting; Chen, Kuan-I; Chiang, Hsin-Han; Chen, Yu-Kuo; Cheng, Kuan-Chen

    2017-01-01

    Pullulan based films possess several advantages, including high transparency, low toxicity, good biodegradability, good mechanical properties, and low oxygen permeability, are preferable for food packaging. The application of pullulan films on food packaging, however, has inherent disadvantage of high water solubility. In this study, glutaraldehyde and glycerol were used as the cross-linking reagent and the plasticizer respectively to improve water resistance and physical properties of the pullulan films. Effects of cross-linking degree on physical properties, including water absorptions, swelling behaviors, water vapor permeability and tensile strengths of films were evaluated. FTIR results demonstrated that the pullulan films were successfully cross-linked by glutaraldehyde. The tensile strength of pullulan films could be enhanced significantly (P glycerol as a plasticizer enhanced the extensibility of films as well as the hydrophilicity, resulting in higher water vapor permeability.

  12. Changes in mechanical properties due to gamma irradiation of high-density polyethylene (HDPE

    Directory of Open Access Journals (Sweden)

    S. S. Cota

    2007-06-01

    Full Text Available This paper presents an experimental analysis of the effect of dose and dose rate parameters during gamma irradiation of high-density polyethylene (HDPE samples. Considerations concerning the influence of these parameters on HDPE mechanical strength properties as a result of the predominance of oxidative degradation or of cross-linking are presented. The experimental results show an improvement of HDPE mechanical strength as dose increases, indicating the predominance of cross-linking over oxidative degradation and that lower doses are necessary to obtain a similar change in resistance parameters when radiation is applied at lower dose rates, showing that gamma radiation affects the HDPE in a more efficient way at lower dose rates.

  13. Changes in mechanical properties due to gamma irradiation of high-density polyethylene (HDPE)

    Energy Technology Data Exchange (ETDEWEB)

    Cota, S.S.; Vasconcelos, V.; Senne Junior, M.; Carvalho, L.L.; Rezende, D.B.; Correa, R.F. [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)]. E-mail: sdsc@cdtn.br

    2007-04-15

    This paper presents an experimental analysis of the effect of dose and dose rate parameters during gamma irradiation of high-density polyethylene (HDPE) samples. Considerations concerning the influence of these parameters on HDPE mechanical strength properties as a result of the predominance of oxidative degradation or of cross-linking are presented. The experimental results show an improvement of HDPE mechanical strength as dose increases, indicating the predominance of cross-linking over oxidative degradation and that lower doses are necessary to obtain a similar change in resistance parameters when radiation is applied at lower dose rates, showing that gamma radiation affects the HDPE in a more efficient way at lower dose rates. (author)

  14. Higher number of pentosidine cross-links induced by ribose does not alter tissue stiffness of cancellous bone

    Energy Technology Data Exchange (ETDEWEB)

    Willems, Nop M.B.K., E-mail: n.willems@acta.nl [Dept. of Orthodontics, Academic Centre for Dentistry Amsterdam (ACTA), University of Amsterdam and VU University, Gustav Mahlerlaan 3004, 1081 LA Amsterdam (Netherlands); Dept. of Oral Cell Biology and Functional Anatomy, MOVE Research Institute, Academic Centre for Dentistry Amsterdam (ACTA), University of Amsterdam and VU University, Gustav Mahlerlaan 3004, 1081 LA Amsterdam (Netherlands); Langenbach, Geerling E.J. [Dept. of Oral Cell Biology and Functional Anatomy, MOVE Research Institute, Academic Centre for Dentistry Amsterdam (ACTA), University of Amsterdam and VU University, Gustav Mahlerlaan 3004, 1081 LA Amsterdam (Netherlands); Stoop, Reinout [Dept. of Metabolic Health Research, TNO, P.O. Box 2215, 2301 CE Leiden (Netherlands); Toonder, Jaap M.J. den [Dept. of Mechanical Engineering, Eindhoven University of Technology, P.O. Box 513, 5600 MB Eindhoven (Netherlands); Mulder, Lars [Dept. of Biomedical Engineering, Eindhoven University of Technology, P.O. Box 513, 5600 MB Eindhoven (Netherlands); Zentner, Andrej [Dept. of Orthodontics, Academic Centre for Dentistry Amsterdam (ACTA), University of Amsterdam and VU University, Gustav Mahlerlaan 3004, 1081 LA Amsterdam (Netherlands); Everts, Vincent [Dept. of Oral Cell Biology and Functional Anatomy, MOVE Research Institute, Academic Centre for Dentistry Amsterdam (ACTA), University of Amsterdam and VU University, Gustav Mahlerlaan 3004, 1081 LA Amsterdam (Netherlands)

    2014-09-01

    The role of mature collagen cross-links, pentosidine (Pen) cross-links in particular, in the micromechanical properties of cancellous bone is unknown. The aim of this study was to examine nonenzymatic glycation effects on tissue stiffness of demineralized and non-demineralized cancellous bone. A total of 60 bone samples were derived from mandibular condyles of six pigs, and assigned to either control or experimental groups. Experimental handling included incubation in phosphate buffered saline alone or with 0.2 M ribose at 37 °C for 15 days and, in some of the samples, subsequent complete demineralization of the sample surface using 8% EDTA. Before and after experimental handling, bone microarchitecture and tissue mineral density were examined by means of microcomputed tomography. After experimental handling, the collagen content and the number of Pen, hydroxylysylpyridinoline (HP), and lysylpyridinoline (LP) cross-links were estimated using HPLC, and tissue stiffness was assessed by means of nanoindentation. Ribose treatment caused an up to 300-fold increase in the number of Pen cross-links compared to nonribose-incubated controls, but did not affect the number of HP and LP cross-links. This increase in the number of Pen cross-links had no influence on tissue stiffness of both demineralized and nondemineralized bone samples. These findings suggest that Pen cross-links do not play a significant role in bone tissue stiffness. - Highlights: • The assessment of effects of glycation in bone using HPLC, microCT, and nanoindentation • Ribose incubation: 300‐fold increase in the number of pentosidine cross-links • 300‐fold increase in the number of pentosidine cross-links: no changes in bone tissue stiffness.

  15. Covalently cross-linked polyetheretherketone proton exchange membrane for DMFC

    CSIR Research Space (South Africa)

    Luo, H

    2009-05-01

    Full Text Available -7 cm2/s) and good electrochemical stability. The results suggested that cross-linked polyetheretherketone membrane is particularly promising to be used as proton exchange membrane for the direct methanol fuel cell application....

  16. Photochemical Patterning of Ionically Cross-Linked Hydrogels

    Directory of Open Access Journals (Sweden)

    Marion Bruchet

    2013-08-01

    Full Text Available Iron(III cross-linked alginate hydrogel incorporating sodium lactate undergoes photoinduced degradation, thus serving as a biocompatible positive photoresist suitable for photochemical patterning. Alternatively, surface etching of iron(III cross-linked hydrogel contacting lactic acid solution can be used for controlling the thickness of the photochemical pattering. Due to biocompatibility, both of these approaches appear potentially useful for advanced manipulation with cell cultures including growing cells on the surface or entrapping them within the hydrogel.

  17. ROLE OF CORNEAL COLLAGEN CROSS LINKING IN KERATOCONUS

    OpenAIRE

    Atul; Superna; Bhimasankar; Vijayleela

    2015-01-01

    To evaluate the outcome of collagen cross linkage using riboflavin 0.1% and ultraviolet A radiation of a wavelength 370nm . PURPOSE : To determine the effect of collagen cross linking for keratoconus on pachymetry , corneal topography, uncorrected visual acuity, specular count, IOP at 1, 3, 6 months . METHODS : The current study was designed as a prospective interventional trial of corneal collagen cross - linking in subjects w...

  18. Filler reinforcement in cross-linked elastomer nanocomposites: insights from fully atomistic molecular dynamics simulation.

    Science.gov (United States)

    Pavlov, Alexander S; Khalatur, Pavel G

    2016-06-28

    Using a fully atomistic model, we perform large-scale molecular dynamics simulations of sulfur-cured polybutadiene (PB) and nanosilica-filled PB composites. A well-integrated network without sol fraction is built dynamically by cross-linking the coarse-grained precursor chains in the presence of embedded silica nanoparticles. Initial configurations for subsequent atomistic simulations are obtained by reverse mapping of the well-equilibrated coarse-grained systems. Based on the concept of "maximally inflated knot" introduced by Grosberg et al., we show that the networks simulated in this study behave as mechanically isotropic systems. Analysis of the network topology in terms of graph theory reveals that mechanically inactive tree-like structures are the dominant structural components of the weakly cross-linked elastomer, while cycles are mainly responsible for the transmission of mechanical forces through the network. We demonstrate that quantities such as the system density, thermal expansion coefficient, glass transition temperature and initial Young's modulus can be predicted in qualitative and sometimes even in quantitative agreement with experiments. The nano-filled system demonstrates a notable increase in the glass transition temperature and an approximately two-fold increase in the nearly equilibrium value of elastic modulus relative to the unfilled elastomer even at relatively small amounts of filler particles. We also examine the structural rearrangement of the nanocomposite subjected to tensile deformation. Under high strain-rate loading, the formation of structural defects (microcavities) within the polymer bulk is observed. The nucleation and growth of cavities in the post-yielding strain hardening regime mainly take place at the elastomer/nanoparticle interfaces. As a result, the cavities are concentrated just near the embedded nanoparticles. Therefore, while the silica nanofiller increases the elastic modulus of the elastomer, it also creates a more

  19. Elasticity of cross-linked semiflexible biopolymers under tension

    CERN Document Server

    von der Heydt, Alice; Benetatos, Panayotis; Zippelius, Annette

    2013-01-01

    Aiming at the mechanical properties of cross-linked biopolymers, we set up and analyze a model of two weakly bending wormlike chains subjected to a tensile force, with regularly spaced inter-chain bonds (cross-links) represented by harmonic springs. Within this model, we compute the force-extension curve and the differential stiffness exactly and discuss several limiting cases. Cross-links effectively stiffen the chain pair by reducing thermal fluctuations transverse to the force and alignment direction. The extra alignment due to cross-links increases both with growing number and with growing strength of the cross-links, and is most prominent for small force f. For large f, the additional, cross-link-induced extension is subdominant except for the case of linking the chains rigidly and continuously along their contour. In this combined limit, we recover asymptotically the elasticity of a weakly bending wormlike chain without constraints, stiffened by a factor four. The increase in differential stiffness can ...

  20. 1,3-Diphenylethenylcarbazolyl-Based Monomer for Cross-Linked Hole Transporting Layers

    Directory of Open Access Journals (Sweden)

    Maryte Daskeviciene

    2015-05-01

    Full Text Available A new cross-linkable monomer containing 1,3-diphenylethenylcarbazolyl-based hole-transporting moieties and four reactive epoxy groups, was prepared by a multistep synthesis route from 1,3-bis(2,2-diphenylethenyl-9H-carbazol-2-ol and its application for the in situ formation of cross-linked hole transporting layers was investigated. A high concentration of flexible aliphatic epoxy chains ensures good solubility and makes this compound an attractive cross-linking agent. The synthesized compounds were characterized by various techniques, including differential scanning calorimetry, xerographic time of flight, and electron photoemission in air methods.

  1. ROMP-based thermosetting polymers from modified castor oil with various cross-linking agents

    Science.gov (United States)

    Ding, Rui

    Polymers derived from bio-renewable resources are finding an increase in global demand. In addition, polymers with distinctive functionalities are required in certain advanced fields, such as aerospace and civil engineering. In an attempt to meet both these needs, the goal of this work aims to develop a range of bio-based thermosetting matrix polymers for potential applications in multifunctional composites. Ring-opening metathesis polymerization (ROMP), which recently has been explored as a powerful method in polymer chemistry, was employed as a unique pathway to polymerize agricultural oil-based reactants. Specifically, a novel norbornyl-functionalized castor oil alcohol (NCA) was investigated to polymerize different cross-linking agents using ROMP. The effects of incorporating dicyclopentadiene (DCPD) and a norbornene-based crosslinker (CL) were systematically evaluated with respect to curing behavior and thermal mechanical properties of the polymers. Isothermal differential scanning calorimetry (DSC) was used to investigate the conversion during cure. Dynamic DSC scans at multiple heating rates revealed conversion-dependent activation energy by Ozawa-Flynn-Wall analysis. The glass transition temperature, storage modulus, and loss modulus for NCA/DCPD and NCA/CL copolymers with different cross-linking agent loading were compared using dynamic mechanical analysis. Cross-link density was examined to explain the very different dynamic mechanical behavior. Mechanical stress-strain curves were developed through tensile test, and thermal stability of the cross-linked polymers was evaluated by thermogravimetric analysis to further investigate the structure-property relationships in these systems.

  2. High Energy Density Laboratory Astrophysics

    CERN Document Server

    Lebedev, Sergey V

    2007-01-01

    During the past decade, research teams around the world have developed astrophysics-relevant research utilizing high energy-density facilities such as intense lasers and z-pinches. Every two years, at the International conference on High Energy Density Laboratory Astrophysics, scientists interested in this emerging field discuss the progress in topics covering: - Stellar evolution, stellar envelopes, opacities, radiation transport - Planetary Interiors, high-pressure EOS, dense plasma atomic physics - Supernovae, gamma-ray bursts, exploding systems, strong shocks, turbulent mixing - Supernova remnants, shock processing, radiative shocks - Astrophysical jets, high-Mach-number flows, magnetized radiative jets, magnetic reconnection - Compact object accretion disks, x-ray photoionized plasmas - Ultrastrong fields, particle acceleration, collisionless shocks. These proceedings cover many of the invited and contributed papers presented at the 6th International Conference on High Energy Density Laboratory Astrophys...

  3. Nondestructive fluorescence-based quantification of threose-induced collagen cross-linking in bovine articular cartilage

    Science.gov (United States)

    Kinnunen, Jussi; Kokkonen, Harri T.; Kovanen, Vuokko; Hauta-Kasari, Markku; Vahimaa, Pasi; Lammi, Mikko J.; Töyräs, Juha; Jurvelin, Jukka S.

    2012-09-01

    Extensive collagen cross-linking affects the mechanical competence of articular cartilage: it can make the cartilage stiffer and more brittle. The concentrations of the best known cross-links, pyridinoline and pentosidine, can be accurately determined by destructive high-performance liquid chromatography (HPLC). We explore a nondestructive evaluation of cross-linking by using the intrinsic fluorescence of the intact cartilage. Articular cartilage samples from bovine knee joints were incubated in threose solution for 40 and 100 h to increase the collagen cross-linking. Control samples without threose were also prepared. Excitation-emission matrices at wavelengths of 220 to 950 nm were acquired from the samples, and the pentosidine and pyridinoline cross-links and the collagen concentrations were determined using HPLC. After the threose treatment, pentosidine and lysyl pyridinole (LP) concentrations increased. The intrinsic fluorescence, excited below 350 nm, decreased and was related to pentosidine [r=-0.90, 240/325 nm (excitation/emission)] or LP (r=-0.85, 235/285 nm) concentrations. Due to overlapping, the changes in emission could not be linked specifically to the recorded cross-links. However, the fluorescence signal enabled a nondestructive optical estimate of changes in the pentosidine and LP cross-linking of intact articular cartilage.

  4. Triosidines: novel Maillard reaction products and cross-links from the reaction of triose sugars with lysine and arginine residues

    National Research Council Canada - National Science Library

    Tessier, Frederic J; Monnier, Vincent M; Sayre, Lawrence M; Kornfield, Julia A

    2003-01-01

    The role of the highly reactive triose sugars glyceraldehyde and glyceraldehyde-3-phosphate in protein cross-linking and other amino acid modifications during the Maillard reaction was investigated...

  5. Cross-linked polyethylenimine–tripolyphosphate nanoparticles for gene delivery

    Directory of Open Access Journals (Sweden)

    Huang XZ

    2014-10-01

    Full Text Available Xianzhang Huang,1 Sujing Shen,2 Zhanfeng Zhang,1 Junhua Zhuang1 1Department of Laboratory Science, Second Affiliated Hospital of Guangzhou University of Chinese Medicine, 2Department of Laboratory Science, Guangdong Second Provincial Traditional Chinese Medicine Hospital, Guangzhou, People’s Republic of China Abstract: The high transfection efficiency of polyethylenimine (PEI makes it an attractive potential nonviral genetic vector for gene delivery and therapy. However, the highly positive charge of PEI leads to cytotoxicity and limits its application. To reduce the cytotoxicity of PEI, we prepared anion-enriched nanoparticles that combined PEI with tripolyphosphate (TPP. We then characterized the PEI-TPP nanoparticles in terms of size, zeta potential, and Fourier-transform infrared (FTIR spectra, and assessed their transfection efficiency, cytotoxicity, and ability to resist deoxyribonuclease (DNase I digestion. The cellular uptake of PEI-TPP with phosphorylated internal ribosome entry site–enhanced green fluorescent protein C1 or FAM (fluorouracil, Adriamycin [doxorubicin] and mitomycin-labeled small interfering ribonucleic acids (siRNAs was monitored by fluorescence microscopy and confocal laser microscopy. The efficiency of transfected delivery of plasmid deoxyribonucleic acid (DNA and siRNA in vitro was 1.11- to 4.20-fold higher with the PEI-TPP particles (7.6% cross-linked than with the PEI, at all N:P ratios (nitrogen in PEI to phosphorus in DNA tested. The cell viability of different cell lines was more than 90% at the chosen N:P ratios of PEI-TPP/DNA complexes. Moreover, PEI-TPP nanoparticles resisted digestion by DNase I for more than 2 hours. The time-dependent absorption experiment showed that 7.6% of cross-linked PEI-TPP particles were internalized by 293T cells within 1 hour. In summary, PEI-TPP nanoparticles effectively transfected cells while conferring little or no toxicity, and thus have potential application in gene

  6. Saturation and High Density QCD

    OpenAIRE

    Mueller, A. H.

    2005-01-01

    Recent progress in understanding general properties of high energy scattering near the unitarity limit, where high density gluon components of the wavefunction are dominant, is reviewed. The similarity of the QCD problem and that of reaction-diffusion processes in statistical physics is emphasized. The energy dependence of the saturation momentum and the status of geometric scaling are discussed.

  7. Sub- T g Cross-Linking of a Polyimide Membrane for Enhanced CO 2 Plasticization Resistance for Natural Gas Separation

    KAUST Repository

    Qiu, Wulin

    2011-08-09

    Decarboxylation-induced thermal cross-linking occurs at elevated temperatures (∼15 °C above glass transition temperature) for 6FDA-DAM:DABA polyimides, which can stabilize membranes against swelling and plasticization in aggressive feed streams. Despite this advantage, such a high temperature might result in collapse of substructure and transition layers in the asymmetric structure of a hollow fibers based on such a material. In this work, the thermal cross-linking of the 6FDA-DAM:DABA at temperatures much below the glass transition temperature (∼387 °C by DSC) was demonstrated. This sub-Tg cross-linking capability enables extension to asymmetric structures useful for large scale membranes. The resulting polymer membranes were characterized by swelling in known solvents for the un-cross-linked materials, TGA analysis, and permeation tests of aggressive gas feed stream at higher pressure. The annealing temperature and time clearly influence the degree of cross-linking of the membranes, and results in a slight difference in selectivity for membranes under various cross-linking conditions. Results indicate that the sub-Tg thermal cross-linking of 6FDA-DAM:DABA dense film membrane can be carried out completely even at a temperature as low as 330 °C. Permeabilities were tested for the polyimide membranes using both pure gases (He, O2, N2, CH4, CO2) and mixed gases (CO2/CH4). The selectivity of the cross-linked membrane can be maintained even under very aggressive CO2 operating conditions that are not possible without cross-linking. Moreover, the plasticization resistance was demonstrated up to 700 psia for pure CO 2 gas or 1000 psia for 50% CO2 mixed gas feeds. © 2011 American Chemical Society.

  8. Probing Protein 3D Structures and Conformational Changes Using Electrochemistry-Assisted Isotope Labeling Cross-Linking Mass Spectrometry

    Science.gov (United States)

    Zheng, Qiuling; Zhang, Hao; Wu, Shiyong; Chen, Hao

    2016-05-01

    This study presents a new chemical cross-linking mass spectrometry (MS) method in combination with electrochemistry and isotope labeling strategy for probing both protein three-dimensional (3D) structures and conformational changes. For the former purpose, the target protein/protein complex is cross-linked with equal mole of premixed light and heavy isotope labeled cross-linkers carrying electrochemically reducible disulfide bonds (i.e., DSP-d0 and DSP-d8 in this study, DSP = dithiobis[succinimidyl propionate]), digested and then electrochemically reduced followed with online MS analysis. Cross-links can be quickly identified because of their reduced intensities upon electrolysis and the presence of doublet isotopic peak characteristics. In addition, electroreduction converts cross-links into linear peptides, facilitating MS/MS analysis to gain increased information about their sequences and modification sites. For the latter purpose of probing protein conformational changes, an altered procedure is adopted, in which the protein in two different conformations is cross-linked using DSP-d0 and DSP-d8 separately, and then the two protein samples are mixed in 1:1 molar ratio. The merged sample is subjected to digestion and electrochemical mass spectrometric analysis. In such a comparative cross-linking experiment, cross-links could still be rapidly recognized based on their responses to electrolysis. More importantly, the ion intensity ratios of light and heavy isotope labeled cross-links reveal the conformational changes of the protein, as exemplified by examining the effect of Ca2+ on calmodulin conformation alternation. This new cross-linking MS method is fast and would have high value in structural biology.

  9. Sensitizing potential of enzymatically cross-linked peanut proteins in a mouse model of peanut allergy.

    NARCIS (Netherlands)

    Smit, Joost|info:eu-repo/dai/nl/250600706

    2014-01-01

    SCOPE: The cross-linking of proteins by enzymes to form high-molecular-weight protein, aggregates can be used to tailor the technological or physiological functionality of food products. Aggregation of dietary proteins by food processing may promote allergic sensitization, but the effects of enzymat

  10. Protein structure prediction guided by cross-linking restraints - A systematic evaluation of the impact of the cross-linking spacer length

    CERN Document Server

    Hofmann, Tommy; Meiler, Jens; Kalkhof, Stefan

    2015-01-01

    Recent development of high-resolution mass spectrometry (MS) instruments enables chemical cross-linking (XL) to become a high-throughput method for obtaining structural information about proteins. Restraints derived from XL-MS experiments have been used successfully for structure refinement and protein-protein docking. However, one formidable question is under which circumstances XL-MS data might be sufficient to determine a protein's tertiary structure de novo? Answering this question will not only include understanding the impact of XL-MS data on sampling and scoring within a de novo protein structure prediction algorithm, it must also determine an optimal cross-linker type and length for protein structure determination. While a longer cross-linker will yield more restraints, the value of each restraint for protein structure prediction decreases as the restraint is consistent with a larger conformational space. In this study, the number of cross-links and their discriminative power was systematically analyz...

  11. Cross-linking of polytetrafluoroethylene during room-temperature irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Pugmire, David L [Los Alamos National Laboratory; Wetteland, Chris J [Los Alamos National Laboratory; Duncan, Wanda S [Los Alamos National Laboratory; Lakis, Rollin E [Los Alamos National Laboratory; Schwartz, Daniel S [Los Alamos National Laboratory

    2008-01-01

    Exposure of polytetrafluoroethylene (PTFE) to {alpha}-radiation was investigated to detennine the physical and chemical effects, as well as to compare and contrast the damage mechanisms with other radiation types ({beta}, {gamma}, or thermal neutron). A number of techniques were used to investigate the chemical and physical changes in PTFE after exposure to {alpha}-radiation. These techniques include: Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), and fluorescence spectroscopy. Similar to other radiation types at low doses, the primary damage mechanism for the exposure of PTFE to {alpha}-radiation appears to be chain scission. Increased doses result in a change-over of the damage mechanism to cross-linking. This result is not observed for any radiation type other than {alpha} when irradiation is performed at room temperature. Finally, at high doses, PTFE undergoes mass-loss (via smallfluorocarbon species evolution) and defluorination. The amount and type of damage versus sample depth was also investigated. Other types of radiation yield damage at depths on the order of mm to cm into PTFE due to low linear energy transfer (LET) and the correspondingly large penetration depths. By contrast, the {alpha}-radiation employed in this study was shown to only induce damage to a depth of approximately 26 {mu}m, except at very high doses.

  12. Collagen/elastin hydrogels cross-linked by squaric acid.

    Science.gov (United States)

    Skopinska-Wisniewska, J; Kuderko, J; Bajek, A; Maj, M; Sionkowska, A; Ziegler-Borowska, M

    2016-03-01

    Hydrogels based on collagen and elastin are very valuable materials for medicine and tissue engineering. They are biocompatible; however their mechanical properties and resistance for enzymatic degradation need to be improved by cross-linking. Up to this point many reagents have been tested but more secure reactants are still sought. Squaric acid (SqAc), 3,4-dihydroxy 3-cyclobutene 1,2-dione, is a strong, cyclic acid, which reacts easily with amine groups. The properties of hydrogels based on collagen/elastin mixtures (95/5, 90/10) containing 5%, 10% and 20% of SqAc and neutralized via dialysis against deionized water were tested. Cross-linked, 3-D, transparent hydrogels were created. The cross-linked materials are stiffer and more resistant to enzymatic degradation than those that are unmodified. The pore size, swelling ability and surface polarity are reduced due to 5% and 10% of SqAc addition. At the same time, the cellular response is not significantly affected by the cross-linking. Therefore, squaric acid would be regarded as a safe, effective cross-linking agent.

  13. Cross-linking reaction kinetics of non-crystalline cassava starch in middle and high temperature wet processes%非晶化木薯淀粉交联反应动力学

    Institute of Scientific and Technical Information of China (English)

    罗明辉; 邓燕芳; 卢龙

    2013-01-01

    以非晶化木薯淀粉为原料,通过湿法交联合成淀粉磷酸酯,研究了非晶化木薯淀粉交联反应动力学过程,计算出表观活化能 Ea,讨论了不同温度对交联反应速率的影响。通过与木薯原淀粉湿法交联对比,研究了非晶化处理对淀粉后续反应的影响。结果表明,非晶化处理后,淀粉交联反应的反应取代度和反应程度均提高,表观活化能降低了23%,反应活性得到大大提高。%The starch diphosphate was synthesized by non-crystalline cassava starch through wet process. The influence of temperature on reaction rate was discussed.The kinetics and apparent activation energy of non-crystalline cassava starch in cross-linking reaction were studied.Compared with raw cassava starch,the influence of non-crystallization on consequent reaction was studied.The results showed the degree of sub-stitution and extent of reaction were both increased after non-crystallization,the apparent activation energy was descended by 23%,and the reaction activity was improved.

  14. Extreme dryness and DNA-protein cross-links

    Science.gov (United States)

    Bieger-Dose, A.; Dose, K.; Meffert, R.; Mehler, M.; Risi, S.

    Exposure of fungal conidia (Aspergillus ochraceus) or spores of Bacillus subtilis to extreme dryness or vacuum induces DNA lesions, including strand breaks and the formation of DNA-protein cross-links. In wet cells only a small amount of protein is bound to DNA, but exposure to conditions of lowered water activity results in an increasing number of cross-links between DNA and proteins. In fungal conidia these cross-links are detected after selective iodination (125J) of the DNA-bound proteins followed by gel electrophoresis and subsequent autoradiography. Another approach is the labelling of DNA with 32p by means of nick translation and the detection of differences in the electrophoretic mobility of DNA before and after digestion with proteinase K of proteins bound to DNA.

  15. Computer simulation of randomly cross-linked polymer networks

    CERN Document Server

    Williams, T P

    2002-01-01

    In this work, Monte Carlo and Stochastic Dynamics computer simulations of mesoscale model randomly cross-linked networks were undertaken. Task parallel implementations of the lattice Monte Carlo Bond Fluctuation model and Kremer-Grest Stochastic Dynamics bead-spring continuum model were designed and used for this purpose. Lattice and continuum precursor melt systems were prepared and then cross-linked to varying degrees. The resultant networks were used to study structural changes during deformation and relaxation dynamics. The effects of a random network topology featuring a polydisperse distribution of strand lengths and an abundance of pendant chain ends, were qualitatively compared to recent published work. A preliminary investigation into the effects of temperature on the structural and dynamical properties was also undertaken. Structural changes during isotropic swelling and uniaxial deformation, revealed a pronounced non-affine deformation dependant on the degree of cross-linking. Fractal heterogeneiti...

  16. Food-contact epoxy resin: co-variation between migration and degree of cross-linking. Part II.

    Science.gov (United States)

    Lambert, C; Larroque, M; Subirats, J T; Gérard, J F

    1998-04-01

    The study of epoxy resin composed of bisphenol A diglycidylether (BADGE), bisphenol F diglycidylether (BFDGE) (base), and primary aliphatic polyamines (hardener), has confirmed the interest of measuring certain physical parameters in order to evaluate the density of cross-linking of the network and thus predict the risks of resin molecules migrating into foodstuffs. This suggestion had been made in a preceding study on an epoxy resin composed of bisphenol A diglycidylether (BADGE) and primary aromatic polyamines. Samples with different densities of cross-linking, obtained by subjecting the resin to different curing temperatures (5, 20, 50 and 90 degrees C) for 7 days, were studied. The density of cross-linking increased with curing temperature, as indicated by the increase in glass transition temperature, the increased stability of the rubber storage modulus E'rub (increase in cross-link nodes), the fall in relaxation enthalpies (reduction in physical ageing) and the decreased amplitude of the loss-factor tan delta (reduction in chain mobility). Maximum cross-linking was obtained in the resin cured at 90 degrees C (temperature above Tg infinity). Concurrently, tests of migration into different liquid food simultants (distilled water, distilled water/ethanol/acetic acid, distilled water/ethanol) revealed a considerable reduction in specific migrations of BADGE and BFDGE, and of unidentified peaks.

  17. High-density multicore fibers

    DEFF Research Database (Denmark)

    Takenaga, K.; Matsuo, S.; Saitoh, K.;

    2016-01-01

    High-density single-mode multicore fibers were designed and fabricated. A heterogeneous 30-core fiber realized a low crosstalk of −55 dB. A quasi-single-mode homogeneous 31-core fiber attained the highest core count as a single-mode multicore fiber....

  18. Effect of Conductive Inorganic Fillers on Space Charge Accumulation Characteristics in Cross-linked Polyethylene

    Science.gov (United States)

    Harada, Hiroshi; Hayashi, Nobuya; Tanaka, Yasuhiro; Maeno, Takashi; Mizuno, Takehiko; Takahashi, Tohru

    We have observed space charge profiles in cross-linked polyethylene (XLPE) under dc high electric field using the PEA (pulsed electro-acoustic) system to study the relationship between space charge behavior and dielectric breakdown. In our previous research work, we have found that a large amount of, so called, packet-like charge generates in low density polyethylene (LDPE) under high dc electric field of more than 100 kV/mm. The packet-like charge enhances the electric field locally in bulk of the sample, and then finally it leads a breakdown. On the other hand, a new type of XLPE which was made through adding conductive inorganic fillers, shows a good dc dielectric breakdown characteristic and high volume resistivity under dc stress. In this report, we tried to observe the space charge behavior under high dc electric field in this material. From the results, it is found that the charge injection is effectively suppressed by adding only a small amount of conductive inorganic fillers to XLPE.

  19. High density matter at RHIC

    Indian Academy of Sciences (India)

    Thomas S Ullrich

    2004-02-01

    QCD predicts a phase transition between hadronic matter and a quark-gluon plasma at high energy density. The relativistic heavy ion collider (RHIC) at Brookhaven National Laboratory is a new facility dedicated to the experimental study of matter under extreme conditions. Already the first round of experimental results at RHIC indicated that the conditions to create a new state of matter are indeed reached in the collisions of heavy nuclei. Studies of particle spectra and their correlations at low transverse momenta provide evidence of strong pressure gradients in the highly interacting dense medium and hint that we observe a system in thermal equilibrium. Recent runs with high statistics allow us to explore the regime of hard-scattering processes where the suppression of hadrons at large transverse momentum, and quenching of di-jets are observed thus providing further evidence for extreme high density matter created in collisions at RHIC.

  20. Structure and kinetics of chemically cross-linked protein gels from small-angle X-ray scattering

    CERN Document Server

    Kaieda, Shuji; Halle, Bertil

    2014-01-01

    Glutaraldehyde (GA) reacts with amino groups in proteins, forming intermolecular cross-links that, at sufficiently high protein concentration, can transform a protein solution into a gel. Although GA has been used as a cross-linking reagent for decades, neither the cross-linking chemistry nor the microstructure of the resulting protein gel have been clearly established. Here we use small-angle X-ray scattering (SAXS) to characterise the microstructure and structural kinetics of gels formed by cross-linking of pancreatic trypsin inhibitor, myoglobin or intestinal fatty acid-binding protein. By comparing the scattering from gels and dilute solutions, we extract the structure factor and the pair correlation function of the gel. The protein gels are spatially heterogeneous, with dense clusters linked by sparse networks. Within the clusters, adjacent protein molecules are almost in contact, but the protein concentration in the cluster is much lower than in a crystal. At the $\\sim$ 1 nm SAXS resolution, the native ...

  1. Laccase-Based CLEAs: Chitosan as a Novel Cross-Linking Agent

    Directory of Open Access Journals (Sweden)

    Alexandre Arsenault

    2011-01-01

    Full Text Available Laccase from Coriolopsis Polyzona was insolubilized as cross-linked enzyme aggregates (CLEAs for the first time with chitosan as the cross-linking agent. Concentrations between 0.01 and 1.867 g/L of chitosan were used and between 0.05 and 600 mM of 1-ethyl-3-(3-dimethylaminopropylcarbodiimide hydrochloride. The laccase was precipitated using ammonium sulphate and cross-linked simultaneously. Specific activity and thermal stability of these biocatalysts were measured. Activities of up to 737 U/g were obtained when 2,2-azino-bis-(3-ethylbenzthiazoline-6-sulfonic acid (ABTS was used as a substrate. Moreover, the stability of these biocatalysts was improved with regards to thermal degradation compared to free laccase when exposed to denaturing conditions of high temperature and low pH. The CLEAs stability against chemical denaturants was also tested but no significant improvement was detected. The total amount of ABTS to be oxidized during thermal degradation by CLEAs and free laccase was calculated and the insolubilized enzymes were reported to oxidize more substrate than free laccase. The formation conditions were analyzed by response surface methodology in order to determine an optimal environment for the production of efficient laccase-based CLEAs using chitosan as the cross-linking agent. After 24 hours of formation at pH 3 and at 4°C without agitation, the CLEAs exhibit the best specific activity.

  2. Cross-linking methods of electrospun fibrinogen scaffolds for tissue engineering applications

    Energy Technology Data Exchange (ETDEWEB)

    Sell, Scott A; Garg, Koyal; McClure, Michael J; Bowlin, Gary L [Department of Biomedical Engineering, Virginia Commonwealth University, Richmond, VA 23284-3067 (United States); Francis, Michael P [Department of Pathology, Virginia Commonwealth University, Richmond, VA 23298-0709 (United States); Simpson, David G [Department of Anatomy and Neurobiology, Virginia Commonwealth University, Richmond, VA 23298-0709 (United States)], E-mail: glbowlin@vcu.edu

    2008-12-15

    The purpose of this study was to enhance the mechanical properties and slow the degradation of an electrospun fibrinogen scaffold, while maintaining the scaffold's high level of bioactivity. Three different cross-linkers were used to achieve this goal: glutaraldehyde vapour, 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide hydrochloride (EDC) in ethanol and genipin in ethanol. Scaffolds with a fibrinogen concentration of 120 mg ml{sup -1} were electrospun and cross-linked with one of the aforementioned cross-linkers. Mechanical properties were determined through uniaxial tensile testing performed on scaffolds incubated under standard culture conditions for 1 day, 7 days and 14 days. Cross-linked scaffolds were seeded with human foreskin fibroblasts (BJ-GFP-hTERT) and cultured for 7, 14 and 21 days, with histology and scanning electron microscopy performed upon completion of the time course. Mechanical testing revealed significantly increased peak stress and modulus values for the EDC and genipin cross-linked scaffolds, with significantly slowed degradation. However, cross-linking with EDC and genipin was shown to have some negative effect on the bioactivity of the scaffolds as cell migration throughout the thickness of the scaffold was slowed.

  3. Effect of dual modification with hydroxypropylation and cross-linking on physicochemical properties of taro starch.

    Science.gov (United States)

    Hazarika, Bidyut Jyoti; Sit, Nandan

    2016-04-20

    Dual modification of taro starch by hydroxypropylation and cross-linking was carried out and the properties of the modified starches were investigated. Two different levels of hydroxypropylation (5 and 10%) and cross-linking (0.05 and 0.10%) were used in different sequences. The amylose contents of the starch decreased due to single and dual modification. For the dual-modified starches, the swelling, solubility and clarity was found to increase with level of hydroxypropylation and decrease with level of cross-linking. The freeze-thaw stability of the dual-modified starches was also affected by the sequence of modification. The viscosities of the cross-linked and dual-modified starches were more than native and hydroxypropylated starches. The firmness of the dual-modified starches was also higher than native and single modified starches. The dual-modified starches have benefits of both type of modifications and could be used for specific purposes e.g. food products requiring high viscosity as well as freeze-thaw stability.

  4. Novel cross linked guar gum-g-poly(acrylate) porous superabsorbent hydrogels: Characterization and swelling behaviour in different environments.

    Science.gov (United States)

    Chandrika, Ksv Poorna; Singh, Anupama; Rathore, Abhishek; Kumar, Anil

    2016-09-20

    A new series of eco-friendly cross linked guar gum-g-poly(acrylate) porous superabsorbent hydrogels was prepared by in situ grafting polymerization and cross-linking on to a natural guar gum employing N,N-methylene bis acrylamide as cross linker. Morphological and structural characterization of the prepared hydrogels (SPHs) done by Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and solid state C(13) NMR spectroscopy confirmed formation of porous grafted and crosslinked hydrogel structure. Increase in cross linker concentration in the feed mass exhibited decrease in porosity and increase in density of the hydrogels. Swelling of an optimized hydrogel (SPH) in response to external stimuli namely, salt solutions, fertilizer solutions, temperature, and pH exhibited high swelling ratios in various environments. Swelling rate of the SPH was faster than the corresponding nonporous superabsorbent hydrogel. The prepared hydrogels can serve as excellent carriers of pesticides, fertilizers and agriculturally important microbes. Biocontrol formulations based on a representative SPH exhibited excellent shelf-life characteristics and bioefficacy against phytopathogenic fungus Pythium aphanidermatum.

  5. A New Life for Cross-Linked Plastic Waste as Aggregates and Binder Modifier for Asphalt Mixtures

    Directory of Open Access Journals (Sweden)

    Liliana M. B. Costa

    2017-06-01

    Full Text Available Every year, millions of tons of plastic waste, with potential to be reused, are wasted in landfills. Based on a literature review and in a local market analysis, cross-linked polyethylene (PEX waste arose as the material with the greatest potential to be tested for incorporation in asphalt mixtures due to the difficulty in its recycling and the lack of solutions for its reuse. Thus, in the present work, mixtures produced with and without PEX were tested in order to compare their performance, aiming at understanding if this waste could successfully be used as an alternative material for this type of application. Thus, water sensitivity, rutting resistance, stiffness modulus and fatigue cracking resistance tests were carried out on asphalt mixtures with up to 5% PEX. Based on the results obtained, it can be concluded that the incorporation of PEX in asphalt mixtures is a viable solution for paving works, especially when high service temperatures are expected. It also decreases the density of the mixture, which can be attractive to lighten structures. Thus, this technology contributes to give new life to cross-linked polyethylene plastic waste.

  6. High density fluoride glass calorimeter

    Science.gov (United States)

    Xie, Q.; Scheltzbaum, J.; Akgun, U.

    2014-04-01

    The unprecedented radiation levels in current Large Hadron Collider runs, and plans to even increase the luminosity creates a need for new detector technologies to be investigated. Quartz plates to replace the plastic scintillators in current LHC calorimeters have been proposed in recent reports. Quartz based Cherenkov calorimeters can solve the radiation damage problem, however light production and transfer have proven to be challenging. This report summarizes the results from a computational study on the performance of a high-density glass calorimeter. High-density, scintillating, fluoride glass, CHG3, was used as the active material. This glass has been developed specifically for hadron collider experiments, and is known for fast response time, in addition to high light yield. Here, the details of a Geant4 model for a sampling calorimeter prototype with 20 layers, and its hadronic as well as electromagnetic performances are reported.

  7. Encapsulation of volatiles by homogenized partially-cross linked alginates.

    Science.gov (United States)

    Inguva, Pavan K; Ooi, Shing Ming; Desai, Parind M; Heng, Paul W S

    2015-12-30

    Cross-linked calcium alginate gels are too viscous to be efficaciously incorporated into spray dried formulations. Thus, viscosity reduction is essential to ensure the processability of calcium alginate gels to be sprayed. Viscosity reduction by high pressure homogenization can open new formulation possibilities. Presently, testing of microcapsule integrity is also limited because either single particle tests neglect collective particle behaviours in bulk or bulk testing methods are often associated with single compressions which may not fully characterize individual particle strengths. The aim of this study was sub-divided into three objectives. First objective was to evaluate the impact of high pressure homogenization on gel viscosity. Second objective was to explore the use of the homogenized gels with modified starch for microencapsulation by spray drying. The final objective was to develop a stamping system as microcapsule strength tester that can assess microcapsules in bulk and evaluate the impact of multiple compressions. Collectively, this study would lead towards developing a pressure-activated patch of microcapsules with encapsulated volatiles and the method to assess the patch efficacy. The alginate gels largely experienced an exponential decay in viscosity when homogenized. Furthermore, the homogenized gels were successfully incorporated in spray drying formulations for microencapsulation. The custom-designed microcapsule strength tester was successfully used and shown to possess the required sensitivity to discern batches of microcapsules containing volatiles to have different release profiles. Addition of homogenized gels strengthened the microcapsules only at high wall to core ratios with low mass-load alginate gels. High mass-load gels weaken the microcapsules, exhibiting a higher release at low stamping pressures and wrinkling on the microcapsules surface.

  8. 1,2,3,4-Diepoxybutane-induced DNA-protein cross-linking in human fibrosarcoma (HT1080) cells.

    Science.gov (United States)

    Gherezghiher, Teshome B; Ming, Xun; Villalta, Peter W; Campbell, Colin; Tretyakova, Natalia Y

    2013-05-03

    1,2,3,4-Diepoxybutane (DEB) is the key carcinogenic metabolite of 1,3-butadiene (BD), an important industrial and environmental chemical present in urban air and in cigarette smoke. DEB is a genotoxic bis-electrophile capable of cross-linking cellular biomolecules to form DNA-DNA and DNA-protein cross-links (DPCs). In the present work, mass spectrometry-based proteomics was employed to characterize DEB-mediated DNA-protein cross-linking in human fibrosarcoma (HT1080) cells. Over 150 proteins including histones, high mobility group proteins, transcription factors, splicing factors, and tubulins were found among those covalently cross-linked to chromosomal DNA in the presence of DEB. A large portion of the cross-linked proteins are known factors involved in DNA binding, transcriptional regulation, cell signaling, DNA repair, and DNA damage response. HPLC-ESI(+)-MS/MS analysis of total proteolytic digests revealed the presence of 1-(S-cysteinyl)-4-(guan-7-yl)-2,3-butanediol conjugates, confirming that DEB forms DPCs between cysteine thiols within proteins and the N-7 guanine positions within DNA. However, relatively high concentrations of DEB were required to achieve significant DPC formation, indicating that it is a poor cross-linking agent as compared to antitumor nitrogen mustards and platinum compounds.

  9. Biochemical properties of bioplastics made from wheat gliadins cross-linked with cinnamaldehyde.

    Science.gov (United States)

    Balaguer, M Pau; Gómez-Estaca, Joaquín; Gavara, Rafael; Hernandez-Munoz, Pilar

    2011-12-28

    The aim of this work has been to study the modification of gliadin films with cinnamaldehyde as a potential cross-linker agent. The molecular weight profile and cross-linking density showed that cinnamaldehyde increased reticulation in the resulting films. The participation of free amino groups of the protein in the newly created entanglements could be a possible mechanism of connection between the polypeptidic chains. The combination of a Schiff base and a Michael addition is a feasible approach to understanding this mechanism. The protein solubility in different media pointed to lower participation by both noncovalent and disulfide bonds in stabilizing the structure of the cross-linked films. The new covalent bonds formed by the cinnamaldehyde treatment hampered water absorption and weight loss, leading to more water-resistant matrices which had not disintegrated after 5 months. The properties of this novel bioplastic could be modified to suit the intended application by using cinnamaldehyde, a naturally occurring compound.

  10. Integrated Cryogenic Satellite Communications Cross-Link Receiver Experiment

    Science.gov (United States)

    Romanofsky, R. R.; Bhasin, K. B.; Downey, A. N.; Jackson, C. J.; Silver, A. H.; Javadi, H. H. S.

    1995-01-01

    An experiment has been devised which will validate, in space, a miniature, high-performance receiver. The receiver blends three complementary technologies; high temperature superconductivity (HTS), pseudomorphic high electron mobility transistor (PHEMT) monolithic microwave integrated circuits (MMIC), and a miniature pulse tube cryogenic cooler. Specifically, an HTS band pass filter, InP MMIC low noise amplifier, HTS-sapphire resonator stabilized local oscillator (LO), and a miniature pulse tube cooler will be integrated into a complete 20 GHz receiver downconverter. This cooled downconverter will be interfaced with customized signal processing electronics and integrated onto the space shuttle's 'HitchHiker' carrier. A pseudorandom data sequence will be transmitted to the receiver, which is in low Earth orbit (LEO), via the Advanced Communication Technology Satellite (ACTS) on a 20 GHz carrier. The modulation format is QPSK and the data rate is 2.048 Mbps. The bit error rate (BER) will be measured in situ. The receiver is also equipped with a radiometer mode so that experiment success is not totally contingent upon the BER measurement. In this mode, the receiver uses the Earth and deep space as a hot and cold calibration source, respectively. The experiment closely simulates an actual cross-link scenario. Since the receiver performance depends on channel conditions, its true characteristics would be masked in a terrestrial measurement by atmospheric absorption and background radiation. Furthermore, the receiver's performance depends on its physical temperature, which is a sensitive function of platform environment, thermal design, and cryocooler performance. This empirical data is important for building confidence in the technology.

  11. Advanced Corneal Cross-Linking System with Fluorescence Dosimetry

    Directory of Open Access Journals (Sweden)

    Marc D. Friedman

    2012-01-01

    Full Text Available Purpose. This paper describes an advanced system that combines corneal cross-linking with riboflavin with fluorescence dosimetry, the ability to measure riboflavin diffusion within the cornea both before and during UVA treatment. Methods and Results. A corneal cross-linking system utilizing a digital micromirror device (DMD was assembled and used to measure diffusion coefficients of 0.1% riboflavin in 20% dextran in porcine eyes. A value of (3.3±0.2×10−7 cm2/s was obtained for the stroma. Diffusion coefficients for the transepithelial formulation of 0.1% riboflavin in 0.44% saline and 0.02% BAK were also measured to be 4.7±0.3×10−8 cm2/s for epithelium only and (4.6±0.4×10−7 cm2/s for stroma only. Riboflavin consumption during a UVA treatment was also demonstrated. Conclusion. A new advanced corneal cross-linking system with fluorescence dosimetry of riboflavin has been demonstrated. It is hoped that this method may play a significant role in determining the underlying mechanisms of corneal cross-linking and assist with the development of additional riboflavin formulations. Moreover, dosimetry may prove valuable in providing a method to account for the biological differences between individuals, potentially informing cornea-specific UVA treatment doses in real time.

  12. The Database of Ribosomal Cross-links: an update.

    OpenAIRE

    Baranov, P V; Kubarenko, A V; Gurvich, O L; Shamolina, T A; Brimacombe, R

    1999-01-01

    The Database of Ribosomal Cross-links (DRC) was created in 1997. Here we describe new data incorporated into this database and several new features of the DRC. The DRC is freely available via World Wide Web at http://visitweb.com/database/ or http://www. mpimg-berlin-dahlem.mpg.de/ approximately ag_ribo/ag_brimacombe/drc/

  13. Elasticity of Rigidly Cross-Linked Networks of Athermal Filaments

    NARCIS (Netherlands)

    Zagar, Goran; Onck, Patrick R.; Van der Giessen, Erik

    2011-01-01

    Actin filaments assemble into network-like structures and play an important role in various cellular mechanical processes. It is known that the response of actin networks cross-linked by stiff proteins is characterized by two distinct regimes: (i) a linear stress strain response for small deformatio

  14. Molecular mechanisms in deformation of cross-linked hydrogel nanocomposite.

    Science.gov (United States)

    Mathesan, Santhosh; Rath, Amrita; Ghosh, Pijush

    2016-02-01

    The self-folding behavior in response to external stimuli observed in hydrogels is potentially used in biomedical applications. However, the use of hydrogels is limited because of its reduced mechanical properties. These properties are enhanced when the hydrogels are cross-linked and reinforced with nanoparticles. In this work, molecular dynamics (MD) simulation is applied to perform uniaxial tension and pull out tests to understand the mechanism contributing towards the enhanced mechanical properties. Also, nanomechanical characterization is performed using quasi static nanoindentation experiments to determine the Young's modulus of hydrogels in the presence of nanoparticles. The stress-strain responses for chitosan (CS), chitosan reinforced with hydroxyapatite (HAP) and cross-linked chitosan are obtained from uniaxial tension test. It is observed that the Young's modulus and maximum stress increase as the HAP content increases and also with cross-linking process. Load displacement plot from pullout test is compared for uncross-linked and cross-linked chitosan chains on hydroxyapatite surface. MD simulation reveals that the variation in the dihedral conformation of chitosan chains and the evolution of internal structural variables are associated with mechanical properties. Additional results reveal that the formation of hydrogen bonds and electrostatic interactions is responsible for the above variations in different systems.

  15. Porous Cross-Linked Polyimide-Urea Networks

    Science.gov (United States)

    Meador, Mary Ann B. (Inventor); Nguyen, Baochau N. (Inventor)

    2015-01-01

    Porous cross-linked polyimide-urea networks are provided. The networks comprise a subunit comprising two anhydride end-capped polyamic acid oligomers in direct connection via a urea linkage. The oligomers (a) each comprise a repeating unit of a dianhydride and a diamine and a terminal anhydride group and (b) are formulated with 2 to 15 of the repeating units. The subunit was formed by reaction of the diamine and a diisocyanate to form a diamine-urea linkage-diamine group, followed by reaction of the diamine-urea linkage-diamine group with the dianhydride and the diamine to form the subunit. The subunit has been cross-linked via a cross-linking agent, comprising three or more amine groups, at a balanced stoichiometry of the amine groups to the terminal anhydride groups. The subunit has been chemically imidized to yield the porous cross-linked polyimide-urea network. Also provided are wet gels, aerogels, and thin films comprising the networks, and methods of making the networks.

  16. Femtosecond laser collagen cross-linking without traditional photosensitizers

    Science.gov (United States)

    Guo, Yizang; Wang, Chao; Celi, Nicola; Vukelic, Sinisa

    2015-03-01

    Collagen cross-linking in cornea has the capability of enhancing its mechanical properties and thereby providing an alternative treatment for eye diseases such as keratoconus. Currently, riboflavin assisted UVA light irradiation is a method of choice for cross-link induction in eyes. However, ultrafast pulsed laser interactions may be a powerful alternative enabling in-depth treatment while simultaneously diminishing harmful side effects such as, keratocyte apoptosis. In this study, femtosecond laser is utilized for treatment of bovine cornea slices. It is hypothesized that nonlinear absorption of femtosecond laser pulses plays a major role in the maturation of immature cross-links and the promotion of their growth. Targeted irradiation with tightly focused laser pulses allows for the absence of a photosensitizing agent. Inflation test was conducted on half treated porcine cornea to identify the changes of mechanical properties due to laser treatment. Raman spectroscopy was utilized to study subtle changes in the chemical composition of treated cornea. The effects of treatment are analyzed by observing shifts in Amide I and Amide III bands, which suggest deformation of the collagen structure in cornea due to presence of newly formed cross-links.

  17. Scleral lens tolerance after corneal cross-linking for keratoconus

    NARCIS (Netherlands)

    Visser, Esther Simone; Soeters, Nienke; Tahzib, Nayyirih G.

    2015-01-01

    Purpose. Subjective and objective evaluation of scleral lens tolerance and fitting before and after corneal cross-linking (CXL) for progressive keratoconus. Methods. In this prospective cohort, evaluations were made of 18 unilateral eyes in patients who underwent CXL and had been wearing scleral len

  18. Lactoferrin binding to transglutaminase cross-linked casein micelles

    NARCIS (Netherlands)

    Anema, S.G.; de Kruif, C.G.

    2012-01-01

    Casein micelles in skim milk were either untreated (untreated milk) or were cross-linked using transglutaminase (TGA-milk). Added lactoferrin (LF) bound to the casein micelles and followed Langmuir adsorption isotherms. The adsorption level was the same in both milks and decreased the micellar zeta

  19. Polyimide Aerogels with Three-Dimensional Cross-Linked Structure

    Science.gov (United States)

    Meador, Mary Ann B. (Inventor)

    2016-01-01

    A method for creating a three dimensional cross-linked polyimide structure includes dissolving a diamine, a dianhydride, and a triamine in a solvent, imidizing a polyamic acid gel by heating the gel, extracting the gel in a second solvent, supercritically drying the gel, and removing the solvent to create a polyimide aerogel.

  20. 21 CFR 177.2420 - Polyester resins, cross-linked.

    Science.gov (United States)

    2010-04-01

    .... Pentaerythritol. Polyoxypropylene ethers of 4,4′-isopropylide-nediphenol (containing an average of 2-7.5 moles of...-pentanediol. (3) Cross-linking agents: Butyl acrylate. Butyl methacrylate. Ethyl acrylate. Ethylhexyl acrylate... the production of the resins or added thereto to impart desired technical or physical...

  1. Cross-linked enzyme aggregates (CLEAs): stable and recyclable biocatalysts

    NARCIS (Netherlands)

    Sheldon, R.A.

    2007-01-01

    The key to obtaining an optimum performance of an enzyme is often a question of devising an effective method for its immobilization. In the present review, we describe a novel, versatile and effective methodology for enzyme immobilization as CLEAs (cross-linked enzyme aggregates). The method is

  2. Hyper-cross-linked, hybrid membranes via interfacial polymerization

    NARCIS (Netherlands)

    Raaijmakers, M.J.T.

    2015-01-01

    Hyper-cross-linked, hybrid membranes consist of covalent networks of alternating organic and inorganic, or biological groups. This thesis reports on the preparation of such hybrid networks via interfacial polymerization. The structure-property relationships of the hybrid networks depend strongly on

  3. High energy density aluminum battery

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Gilbert M.; Paranthaman, Mariappan Parans; Dai, Sheng; Dudney, Nancy J.; Manthiram, Arumugan; McIntyre, Timothy J.; Sun, Xiao-Guang; Liu, Hansan

    2016-10-11

    Compositions and methods of making are provided for a high energy density aluminum battery. The battery comprises an anode comprising aluminum metal. The battery further comprises a cathode comprising a material capable of intercalating aluminum or lithium ions during a discharge cycle and deintercalating the aluminum or lithium ions during a charge cycle. The battery further comprises an electrolyte capable of supporting reversible deposition and stripping of aluminum at the anode, and reversible intercalation and deintercalation of aluminum or lithium at the cathode.

  4. High energy density aluminum battery

    Science.gov (United States)

    Brown, Gilbert M.; Paranthaman, Mariappan Parans; Dai, Sheng; Dudney, Nancy J.; Manthiram, Arumugan; McIntyre, Timothy J.; Sun, Xiao-Guang; Liu, Hansan

    2016-10-11

    Compositions and methods of making are provided for a high energy density aluminum battery. The battery comprises an anode comprising aluminum metal. The battery further comprises a cathode comprising a material capable of intercalating aluminum or lithium ions during a discharge cycle and deintercalating the aluminum or lithium ions during a charge cycle. The battery further comprises an electrolyte capable of supporting reversible deposition and stripping of aluminum at the anode, and reversible intercalation and deintercalation of aluminum or lithium at the cathode.

  5. Injectable, high-density collagen gels for annulus fibrosus repair: An in vitro rat tail model.

    Science.gov (United States)

    Borde, Brandon; Grunert, Peter; Härtl, Roger; Bonassar, Lawrence J

    2015-08-01

    A herniated intervertebral disc often causes back pain when disc tissue is displaced through a damaged annulus fibrosus. Currently, the only methods available for annulus fibrosus repair involve mechanical closure of defect, which does little to address biological healing in the damaged tissue. Collagen hydrogels are injectable and have been used to repair annulus defects in vivo. In this study, high-density collagen hydrogels at 5, 10, and 15 mg/mL were used to repair defects made to intact rat caudal intervertebral discs in vitro. A group of gels at 15 mg/mL were also cross-linked with riboflavin at 0.03 mM, 0.07 mM, or 0.10 mM. These cross-linked, high-density collagen gels maintained their presence in the defect under loading and contributed positively to the mechanical response of damaged discs. Discs exhibited increases to 95% of undamaged effective equilibrium and instantaneous moduli as well as up to fourfold decreases in effective hydraulic permeability from the damaged discs. These data suggest that high-density collagen gels may be effective at restoring mechanical function of injured discs as well as potential vehicles for the delivery of biological agents such as cells or growth factors that may aid in the repair of the annulus fibrosus.

  6. Oegylated and cross-linking carbazole dendrons and dendrimers: Synthesis, characterization, assembly and thin film fabrication

    Science.gov (United States)

    Felipe, Mary Jane Legaspi

    2011-12-01

    Dendrimers and dendrons (fractional dendrimers) are macromolecular structures that have well-defined molecular weights and precise number of functional groups. Tailoring these structures has provided designer molecules that can be used for various applications including drug delivery, sensors, and anti-biofouling surfaces. Overall, this dissertation provides novel protocols for the understanding of molecular design, synthesis, and structure-property relationship of OEGylated and conjugated carbazole dendrons and dendrimers. In this design, the use of oligo(ethylene glycol) (OEG) allows for the fabrication of biocompatible materials and imparts hydrophilicity on the structure while the carbazole functionality allows the cross-linking of these designer molecules. Such fine-tuning of macromolecular structures leading to the fabrication of anti-biofouling thin films, nanostructuring at the air-water interface, and assembly into supramolecular superstructures are considered in this dissertation. Chapter 2 details the synthesis, characterization, and electrochemical cross-linking of OEGylated linear dendrons and "Janus-type" dendrimers. Cross-linking the carbazole moieties enables the deposition of these films on Au, indium tin oxide-coated glass, and doped silicon through cyclic voltammetry and provides films with secondary level of organization imparted by the inter- and intra-molecular interaction among the carbazole units. Chapter 3 describes the fabrication of nonspecific protein adsorption resistant surfaces through electrochemical grafting of three different dendrons on SAM carbazole-coated gold substrates. The predictable shape of each dendron and the ability to cross-link the carbazole units have enabled parametrization of OEG conformation and density on these interfaces. Chapter 4 demonstrates the fundamental architectural requirements for obtaining stable films with OEGylated linear dendron molecules providing a new architectural design of nanostructuring

  7. Preparation of High Strength Silicon Nitride Ceramic Fibers From Polycarbosilane Fibers byγ-Ray Irradiation and Thermal Cross-Linking%γ辐照联合热交联聚碳硅烷先驱丝热解制备高强度氮化硅陶瓷纤维

    Institute of Scientific and Technical Information of China (English)

    黎阳; 高家诚; 许云书

    2014-01-01

    在空气气氛中采用γ射线辐照处理聚碳硅烷(PCS)先驱丝,辐照先驱丝经 Ar中热交联、NH3中热解氨化、N2中高温氮化处理制备了氮化硅陶瓷纤维。研究了热交联处理对辐照先驱丝化学结构、凝胶含量、氨化陶瓷产率、抗拉强度、微观形貌及氧含量的影响。结果表明:热交联处理生成了 Si—CH2—Si 和 Si—O—Si 桥连结构,桥连结构使PCS先驱丝实现凝胶化;热交联处理不仅大幅提高了辐照 PCS先驱丝的氨化陶瓷产率,还提高了热解所得氮化硅陶瓷纤维的抗拉强度,而且还降低了陶瓷纤维的氧含量;吸收剂量为1.0 MGy的辐照丝经热交联处理后,其热解所得氮化硅陶瓷纤维抗拉强度达2.05 GPa,氧质量分数仅为9.5%。%Polycarbosilane (PCS)precursor fibers were irradiated byγ-ray in air.Silicon nitride ceramic fibers were obtained from the irradiated PCS fibers by process of thermal cross-linking treatment in Ar,ammoniation pyrolysis in NH3 and high temperature nitriding treatment in N2 .The effects of thermal cross-linking treatment on chemical structure,gel content,ammoniation ceramic yield,tensile strength,microstructure and oxygen content were studied.The results show that bridge structures of Si—CH2—Si and Si—O—Si are formed in the PCS fibers by thermal cross-linking treatment and make the PCS fibers become gelling.The ammoniation ceramic yield of the irradiated PCS fibers increases sharply after thermal cross-linking treatment.The tensile strength of the silicon nitride ceramic fibers increases sharply, while the oxygen content decreases. After thermal cross-linking treatment,the tensile strength of the silicon nitride ceramic fibers derived from the PCS fibers with absorbed dose of 1.0 MGy reaches 2.05 GPa and the oxygen mass fraction is 9.5%.

  8. Wood Sawdust/Natural Rubber Ecocomposites Cross-Linked by Electron Beam Irradiation

    Directory of Open Access Journals (Sweden)

    Elena Manaila

    2016-06-01

    Full Text Available The obtaining and characterization of some polymeric eco-composites based on wood sawdust and natural rubber is presented. The natural rubber was cross-linked using the electron beam irradiation. The irradiation doses were of 75, 150, 300 and 600 kGy and the concentrations of wood sawdust were of 10 and 20 phr, respectively. As a result of wood sawdust adding, the physical and mechanical properties such as hardness, modulus at 100% elongation and tensile strength, showed significant improvements. The presence of wood sawdust fibers has a reinforcing effect on natural rubber, similar or better than of mineral fillers. An increase in the irradiation dose leads to the increasing of cross-link density, which is reflected in the improvement of hardness, modulus at 100% elongation and tensile strength of blends. The cross-linking rates, appreciated using the Flory-Rehner equation, have increased with the amount of wood sawdust in blends and with the irradiation dose. Even if the gel fraction values have varied irregularly with the amount of wood sawdust and irradiation dose it was over 90% for all blends, except for the samples without wood sawdust irradiated with 75 kGy. The water uptake increased with increasing of fiber content and decreased with the irradiation dose.

  9. Effect of Addition of Soybean Oil and Gamma-Ray Cross-linking on the Nanoporous HDPE Membrane

    Directory of Open Access Journals (Sweden)

    Jong-Seok Park

    2012-01-01

    Full Text Available A nanoporous high-density polyethylene (HDPE membrane was prepared by a wet process. Soybean oil and dibutyl phthalate (DBP were premixed as codiluents, and gamma-rays were used for the cross-linking of HDPE. The pore volume of the nanoporous HDPE membranes with soybean oil was affected by the extracted amount of oil. The tensile strength of the membrane improved with an increasing absorbed dose up to 60 kGy, but decreased at 80 kGy due to severe degradation. The ionic conductivity of the nanoporous HDPE membrane did not really change with an increasing absorbed dose because the pores had already been formed before the gamma-ray radiation. Finally, the electrochemical stability of the HDPE membrane increased when the absorbed dose increased up to 60 kGy.

  10. Fabrication and properties of irradiation-cross-linked poly(vinyl alcohol)/clay aerogel composites.

    Science.gov (United States)

    Chen, Hong-Bing; Liu, Bo; Huang, Wei; Wang, Jun-Sheng; Zeng, Guang; Wu, Wen-Hao; Schiraldi, David A

    2014-09-24

    Poly(vinyl alcohol) (PVOH)/clay aerogel composites were fabricated by an environmentally friendly freeze-drying of the aqueous precursor suspensions, followed by cross-linking induced by gamma irradiation without chemical additives. The influences of cross-linking conditions, i.e., absorbed dose and polymer loading as well as density on the aerogel structure and properties, were investigated. The absorbed dose of 30 kGy was found to be the optimum dose for fabricating strong PVOH composites; the compressive modulus of an aerogel prepared from an aqueous suspension containing 2 wt % PVOH/8 wt % clay increased 10-fold, and that containing 1 wt % PVOH/9 wt % clay increased 12 times upon cross-linking with a dose of 30 kGy. Increasing the solids concentration led to an increase in the mechanical strength, in accordance with the changes in microstructure from layered structure to network structure. The increase of absorbed dose also led to decreased porous size of the network structure. Cross-linking and the increase of the PVOH lead to decreased thermal stability. The strengthened PVOH/clay aerogels possess very low flammability, as measured by cone calorimetry, with heat, smoke, and volatile products release value decreasing as increasing clay content. The mechanism of flame retardation in these materials was investigated with weight loss, FTIR, WAXD, and SEM of the burned residues. The proposed mechanism is that with decreasing fuel content (increasing clay content), increased heat and mass transport barriers are developed; simultaneously low levels of thermal conductivity are maintained during the burning.

  11. Effectiveness of trimethylopropane trimethacrylate for the electron-beam-irradiation-induced cross-linking of polylactic acid

    Science.gov (United States)

    Ng, Hon-Meng; Bee, Soo-Tueen; Ratnam, C. T.; Sin, Lee Tin; Phang, Yee-Yao; Tee, Tiam-Ting; Rahmat, A. R.

    2014-01-01

    The purpose of this research was to investigate the effects of various loading levels of trimethylopropane trimethacrylate (TMPTMA) on the properties of polylactic acid (PLA) cross-linked via electron-beam irradiation. PLA was compounded with 3-5 wt.% of TMPTMA to induce cross-linking upon subjection to electron-beam irradiation doses of 25-250 kGy. The physical properties of the PLA samples were characterised by means of X-ray diffraction, gel fraction and scanning electron microscopy analyses on fractured surfaces after tensile tests. The presence of TMPTMA in PLA was found to effectively increase the crystallite size and gel fraction. However, higher loading levels of TMPTMA could compromise the properties of the PLA/TMPTMA samples, indicating that a larger amount of monomer free radicals might promote degradation within the substantially cross-linked amorphous phase. Irradiation-induced cross-linking in the samples could improve the cross-linking density while decreasing the elongation and interfering with the crystallisation. These effects are caused by the intensive irradiation-induced chain scission that is responsible for the deterioration of the mechanical and crystalline properties of the samples.

  12. Study on Electric Charge Trapping in Cross-linking Polyethylene and Byproducts by using Molecular Orbital Calculation

    Science.gov (United States)

    Takada, Tatsuo; Hayase, Yuji; Miyake, Hiroaki; Tanaka, Yasuhiro; Yoshida, Masafumi

    This paper reports an examination of hetero-space charge trapping site in cross linked polyethylene (XLPE) using Molecular Orbital calculation. We chose a simple model for polyethylene (C24H50) with one molecular of acetophenone (one of cross linking byproducts), for the examination of XLPE sample. Molecular Orbital calculation can give the microscopic information of electron energy levels, electron density distributions and electro-static potential maps for the simple molecular mode of XLPE. It is presumed that the negative hetero-space charge (electron) and positive hetero-space charge (hole) were trapped at the permanent dipole of acetophenone, and the hole carrier could move in the polyethylene chain.

  13. Oxidation increases mucin polymer cross-links to stiffen airway mucus gels.

    Science.gov (United States)

    Yuan, Shaopeng; Hollinger, Martin; Lachowicz-Scroggins, Marrah E; Kerr, Sheena C; Dunican, Eleanor M; Daniel, Brian M; Ghosh, Sudakshina; Erzurum, Serpel C; Willard, Belinda; Hazen, Stanley L; Huang, Xiaozhu; Carrington, Stephen D; Oscarson, Stefan; Fahy, John V

    2015-02-25

    Airway mucus in cystic fibrosis (CF) is highly elastic, but the mechanism behind this pathology is unclear. We hypothesized that the biophysical properties of CF mucus are altered because of neutrophilic oxidative stress. Using confocal imaging, rheology, and biochemical measures of inflammation and oxidation, we found that CF airway mucus gels have a molecular architecture characterized by a core of mucin covered by a web of DNA and a rheological profile characterized by high elasticity that can be normalized by chemical reduction. We also found that high levels of reactive oxygen species in CF mucus correlated positively and significantly with high concentrations of the oxidized products of cysteine (disulfide cross-links). To directly determine whether oxidation can cross-link mucins to increase mucus elasticity, we exposed induced sputum from healthy subjects to oxidizing stimuli and found a marked and thiol-dependent increase in sputum elasticity. Targeting mucin disulfide cross-links using current thiol-amino structures such as N-acetylcysteine (NAC) requires high drug concentrations to have mucolytic effects. We therefore synthesized a thiol-carbohydrate structure (methyl 6-thio-6-deoxy-α-D-galactopyranoside) and found that it had stronger reducing activity than NAC and more potent and fast-acting mucolytic activity in CF sputum. Thus, oxidation arising from airway inflammation or environmental exposure contributes to pathologic mucus gel formation in the lung, which suggests that it can be targeted by thiol-modified carbohydrates.

  14. Transient Anisocoria after Corneal Collagen Cross-Linking

    Science.gov (United States)

    Kymionis, George D.; Grentzelos, Michael A.; Stojanovic, Nela; Paraskevopoulos, Theodore A.; Detorakis, Efstathios T.

    2014-01-01

    Purpose. To report a case with transient anisocoria after corneal collagen cross-linking (CXL). Methods. Case report. Results. A 24-year-old male underwent corneal collagen cross-linking (CXL) in his right eye for keratoconus. At the end of the procedure, the pupil of the treated eye was irregular and dilated, while the pupil of the fellow eye was round, regular, and reactive (anisocoria). The following day, pupils were round, regular, and reactive in both eyes. Conclusion. Anisocoria may be a transient and innocuous complication after CXL. A possible cause for this complication might be the anesthetic drops used before and during the surgical procedure or/and the ultraviolet A irradiation during the treatment. PMID:25276451

  15. Transient Anisocoria after Corneal Collagen Cross-Linking

    Directory of Open Access Journals (Sweden)

    George D. Kymionis

    2014-01-01

    Full Text Available Purpose. To report a case with transient anisocoria after corneal collagen cross-linking (CXL. Methods. Case report. Results. A 24-year-old male underwent corneal collagen cross-linking (CXL in his right eye for keratoconus. At the end of the procedure, the pupil of the treated eye was irregular and dilated, while the pupil of the fellow eye was round, regular, and reactive (anisocoria. The following day, pupils were round, regular, and reactive in both eyes. Conclusion. Anisocoria may be a transient and innocuous complication after CXL. A possible cause for this complication might be the anesthetic drops used before and during the surgical procedure or/and the ultraviolet A irradiation during the treatment.

  16. Light-harvesting cross-linked polymers for efficient heterogeneous photocatalysis.

    Science.gov (United States)

    Wang, Cheng; Xie, Zhigang; deKrafft, Kathryn E; Lin, Wenbin

    2012-04-01

    Nonporous, phosphorescent cross-linked polymers (Ru-CP and Ir-CP) were synthesized via Pd-catalyzed Sonogashira cross-coupling reactions between tetra(p-ethynylphenyl)methane and dibrominated Ru(bpy)(3)(2+) or Ir(ppy)(2)(bpy)(+), respectively. The resultant particulate cross-linked polymer (CP) materials have very high catalyst loadings (76.3 wt % for Ru-CP and 71.6 wt % for Ir-CP), and are nonporous with negligibly small surface areas (2.9 m(2)/g for Ru-CP and 2.7 m(2)/g for Ir-CP). Despite their nonporous nature, the insoluble CP materials serve as highly active and recyclable heterogeneous photocatalysts for a range of organic transformations such as aza-Henry reaction, aerobic amine coupling, and dehalogenation of benzyl bromoacetate. An efficient light-harvesting mechanism, which involves collection of photons by exciting the (3)MLCT states of the phosphors and migration of the excited states to the particle surface, is proposed to account for the very high catalytic activities of these nonporous CPs. Steady-state and time-resolved emission data, as well as the reduced catalytic activity of Os(bpy)(3)(2+)-doped Ru-CPs supports efficient excited state migration for the CP frameworks. This work uncovers a new strategy in designing highly efficient photocatalysts based on light-harvesting cross-linked polymers.

  17. The effect of an additional phosphite stabilizer on the properties of radiation cross-linked vitamin E blends of UHMWPE.

    Science.gov (United States)

    Oral, Ebru; Neils, Andrew; Yabannavar, Pooja; Muratoglu, Orhun K

    2014-06-01

    Antioxidant stabilization of radiation cross-linked ultrahigh molecular weight polyethylene (UHMWPE) has been introduced to improve the oxidative stability of total joint implant bearing surfaces. Blending of an antioxidant with UHMWPE resin powder followed by consolidation and radiation cross-linking has been cleared by the FDA for use in both total hips and total knees for designs incorporating two antioxidants, namely vitamin E and Covernox™ (a medical grade version of Irganox™ 1010). The antioxidants in the polymer are expected to protect the polymer during consolidation, during radiation cross-linking, on the shelf before implantation, and in vivo after implantation. To maximize the protection of the polymer afforded by the antioxidant in vivo, a novel approach may be the use of multiple antioxidants, especially to protect the primary antioxidant for a longer period of time. We hypothesized that the addition of a phosphite stabilizer (Irgafos 168™) commonly used in conjunction with hindered phenolic antioxidants in polymer processing could improve the oxidative stability of radiation cross-linked blends of vitamin E. To test our hypothesis, we prepared UHMWPE blends with 0.05 wt% Irgafos and 0.05 wt% vitamin E and compared its cross-link density, wear resistance, tensile properties, and impact strength to control blends containing only vitamin E. Our hypothesis was not supported; the cross-link density of UHMWPE was significantly decreased by the additive without additional benefit to oxidative stability. To our knowledge, this was the first attempt at using multiple stabilizers in medical grade UHMWPE.

  18. EFFECT OF CROSSLINK DENSITY ON THE HIGH PRESSURE CRYSTALLIZATION OF UHMWPE

    Science.gov (United States)

    Oral, Ebru; Beckos, Christine Godleski; Ghali, Bassem W.; Lozynsky, Andrew J.; Muratoglu, Orhun K.

    2010-01-01

    Ultrahigh molecular weight polyethylene (UHMWPE) is a bearing surface material for total joint implants. It is radiation cross-linked for high wear resistance and is melted or treated with vitamin E for oxidative stability. We investigated high pressure crystallization (HPC) of irradiated UHMWPE as an alternative method to improve the mechanical strength while stabilizing the residual free radicals from radiation crosslinking. HPC of uncross-linked UHMWPE has resulted in the formation of extended chain crystals and increased crystallinity, leading to improved strength. We hypothesized that increased cross-link density would hinder crystallization during HPC due to decreased chain mobility. Therefore, we investigated the crystalline structure and tensile mechanical properties of high pressure crystallized 25-, 65- and 100-kGy irradiated UHMWPE. We also determined free radical content and wear. The strength of 25- and 65-kGy irradiated UHMWPEs was improved by HPC with increased crystallinity and crystal size. 100-kGy irradiated UHMWPE did not show improved strength, supporting our hypothesis that decreased chain mobility would hinder crystal formation and strength improvement. None of the HPC irradiated UHMWPEs contained detectable free radicals and their wear properties were maintained, suggesting oxidative and mechanical stability in the long term. Therefore, HPC can be used effectively for imparting oxidative stability while strength improvement can be achieved for irradiated UHMWPE with low to moderate crosslink density. PMID:19213055

  19. Electrochemical Characterization of Ultrathin Cross-Linked Metal Nanoparticle Films.

    Science.gov (United States)

    Han, Chu; Percival, Stephen J; Zhang, Bo

    2016-09-06

    Here we report the preparation, characterization, and electrochemical study of conductive, ultrathin films of cross-linked metal nanoparticles (NPs). Nanoporous films ranging from 40 to 200 nm in thickness composed of gold and platinum NPs of ∼5 nm were fabricated via a powerful layer-by-layer spin coating process. This process allows preparation of uniform NP films as large as 2 × 2 cm(2) with precise control over thickness, structure, and electrochemical and electrocatalytic properties. Gold, platinum, and bimetallic NP films were fabricated and characterized using cyclic voltammetry, scanning electron microscopy, and conductance measurements. Their electrocatalytic activity toward the oxygen reduction reaction (ORR) was investigated. Our results show that the electrochemical activity of such NP films is initially hindered by the presence of dense thiolate cross-linking ligands. Both electrochemical cycling and oxygen plasma cleaning are effective means in restoring their electrochemical activity. Gold NP films have higher electric conductivity than platinum possibly due to more uniform film structure and closer particle-particle distance. The electrochemical and electrocatalytic performance of platinum NP films can be greatly enhanced by the incorporation of gold NPs. This work focuses on electrochemical characterization of cross-linked NP films and demonstrates several unique properties. These include quick and easy preparation, ultrathin and uniform film thickness, tunable structure and composition, and transferability to many other substrates.

  20. Poly(methyl vinyl ether-co-maleic acid)-polyethylene glycol nanocomposites cross-linked in situ with cellulose nanowhiskers.

    Science.gov (United States)

    Goetz, Lee; Foston, Marcus; Mathew, Aji P; Oksman, Kristiina; Ragauskas, Arthur J

    2010-10-11

    Nanocomposites were developed by cross-linking cellulose nanowhiskers with poly(methyl vinyl ether-co-maleic acid) and polyethylene glycol. Nuclear magnetic resonance (NMR) studies showed cross-linking occurs between the matrix and cellulose nanowhiskers via an esterification reaction. Proton NMR T(2) relaxation experiments provided information on the mobility of the polymer chains within the matrix, which can be related to the structure of the cross-linked nanocomposite. The nanocomposite was found to consist of mobile chain portions between cross-linked junction points and immobilized chain segments near or at those junction points, whose relative fraction increased upon further incorporation of cellulose nanowhiskers. Atomic force microscopy images showed a homogeneous dispersion of nanowhiskers in the matrix even at high nanowhisker content, which can be attributed to cross-linking of the nanowhiskers in the matrix. Relative humidity conditions were found to affect the mechanical properties of the composites negatively while the nanowhiskers content had a positive effect. It is expected that the cross-links between the matrix and the cellulose nanowhiskers trap the nanowhiskers in the cross-linked network, preventing nanowhisker aggregation subsequently producing cellulose nanocomposites with unique mechanical behaviors. The results show that in situ cross-linking of cellulose nanowhiskers with a matrix polymer is a promising route to obtain nanocomposites with well dispersed nanowhiskers, tailored nanostructure, and mechanical performance.

  1. Thermally Conductive-Silicone Composites with Thermally Reversible Cross-links.

    Science.gov (United States)

    Wertz, J T; Kuczynski, J P; Boday, D J

    2016-06-08

    Thermally conductive-silicone composites that contain thermally reversible cross-links were prepared by blending diene- and dienophile-functionalized polydimethylsiloxane (PDMS) with an aluminum oxide conductive filler. This class of thermally conductive-silicones are useful as thermal interface materials (TIMs) within Information Technology (IT) hardware applications to allow rework of valuable components. The composites were rendered reworkable via retro Diels-Alder cross-links when temperatures were elevated above 130 °C and required little mechanical force to remove, making them advantageous over other TIM materials. Results show high thermal conductivity (0.4 W/m·K) at low filler loadings (45 wt %) compared to other TIM solutions (>45 wt %). Additionally, the adhesion of the material was found to be ∼7 times greater at lower temperatures (25 °C) and ∼2 times greater at higher temperatures (120 °C) than commercially available TIMs.

  2. Monitoring human lymphocytic DNA-protein cross-links as biomarkers of biologically active doses of chromate.

    Science.gov (United States)

    Costa, M; Zhitkovich, A; Toniolo, P; Taioli, E; Popov, T; Lukanova, A

    1996-10-01

    A simple and sensitive assay for DNA-protein cross-links has been used as a biomarker of chromate exposure and early carcinogenic effects. Pilot studies of DNA-protein cross-links in peripheral blood lymphocytes have been conducted with individuals who had higher exposure to chromate, including welders, and with individuals who had lower levels of exposure such as residents living in a chromium-contaminated area in Jersey City, New Jersey. Studies were also conducted in two Bulgarian cities (Jambol and Burgas) with different levels of air pollution and Cr(VI) exposure and in chrome platers in Bulgaria who had high exposure to chromate. DNA-protein cross-links in U.S. welders and in individuals living in Hudson County, New Jersey around chromium-contaminated areas were significantly higher compared to matched controls. Although blood and urinary levels of chromium were not extensively studied in these populations, we were able to obtain these measurements in the Bulgarian population. Chromium levels in red blood cells of controls living in Burgas were in the order of 1 to 2 ppb chromium, and these individuals had the lowest levels of DNA-protein cross-links. However, the chromium levels in Jambol ranged from about 2 to 7 ppb in red blood cells of city residents to about 22 ppb in chrome platers. DNA-protein cross-links were saturated at about 7 to 8 ppb chromium in the red blood cells, and cross-links correlated well only with chromium levels in red blood cells. Urinary chromium levels did not correlate well with either DNA-protein cross-links or chromium levels in with red blood cells.

  3. Scleral wound healing with cross-link technique using riboflavin and ultraviolet A on rabbit eyes.

    Science.gov (United States)

    Damasceno, Nadyr A; Miguel, Nadia C; Ventura, Marcelo Palis; Burnier, Miguel; Avila, Marcos P; Damasceno, Eduardo F

    2017-01-01

    The aim of study was to evaluate the cross-link using riboflavin and ultraviolet A (UVA) for improving scleral wound healing. This was an experimental study involving four New Zealand rabbits (eight eyes). Therapy procedure was chosen for the right eye and control procedure for the left one. UVA irradiation of 365 nm with a surface irradiance of 3 mW/cm(2) and a photosensitizer of riboflavin drops were applied for 30 minutes on the right eye at 2 mm from the limbus. Sclerotomy incision was performed at 2 mm from the limbus in both right (on the cross-link-treated area) and left eye. Then, 30 days after surgery, a morphological analysis and histological staining with hematoxylin-eosin and picrosirius red were performed, and the sclerotomy cicatrization of right and left eyes was compared. The variables investigated were as follows: sclerotomy incision pictures and measurements were made using the ImageJ Software. Scleral thickness was measured (employing the anterior optical coherence tomography and the digital caliper). Collagen fiber density stained with picrosirius red staining was measured using the Image Pro Plus software. The morphological analysis showed that in all samples, the right eye presented sclerotomy closure, and in two eyes, among them, there were no visible edges of the sclerotomies incision. The left eye presented sclerotomy closure and incision edges. The Image Pro demonstrated a higher density of collagen fibers in the right eye when compared to the one. The statistical analysis was significant when compared to the collagen fiber density in the treated eyes with the control eyes. The cross-link procedure resulted in a better sclerotomy wound healing.

  4. Fluorescent and cross-linked organic-inorganic hybrid nanoshells for monitoring drug delivery.

    Science.gov (United States)

    Sun, Lijuan; Liu, Tianhui; Li, Hua; Yang, Liang; Meng, Lingjie; Lu, Qinghua; Long, Jiangang

    2015-03-04

    Functionalized and monodisperse nanoshells have attracted significant attention owing to their well-defined structure, unique properties, and wide range of potential applications. Here, the synthesis of cross-linked organic-inorganic hybrid nanoshells with strong fluorescence properties was reported via a facile precipitation polymerization of hexachlorocyclotriphosphazene (HCCP) and fluorescein on silica particles used as templates. The resulting poly(cyclotriphosphazene-co-fluorescein) (PCTPF) nanoshells were firm cross-linked shells with ∼2.2 nm mesopores that facilitated the transport of drug molecules. The fluorescent nanoshells also exhibited excellent water dispersibility and biocompatibility; thus, they can be considered as ideal drug vehicles with high doxorubicin storage capacity (26.2 wt %) and excellent sustained release (up to 14 days). Compared to doxorubicin (DOX) alone, the PCTPF nanoshells more efficiently delivered DOX into and killed cancer cells. Moreover, the PCTPF nanoshells also exhibited remarkable fluorescent emission properties and improved photobleaching stability in both suspension and solid state owing to the covalent immobilization of fluorescein in the highly cross-linked organic-inorganic hybrids. The exceptional fluorescent properties enabled the release of DOX as well as the distribution of nanoshells and DOX to be monitored.

  5. Synthesis of cross-linked carbon nanotube mats and their applications

    Science.gov (United States)

    Ventura, Darryl N.

    2011-12-01

    Carbon nanotubes (CNTs) possess excellent tensile strength and electron transport properties that make them a promising component in future materials and technologies. The covalent cross-linking of carbon nanotubes is one avenue of producing thin, flexible mats that can be used in a variety of applications. Here we describe the cross-linking of functionalized CNTs through the Michael addition and imine formation reaction schemes. Our method of cross-linking is an improvement over traditional techniques such as laser irradiation because it is not detrimental to the nanotube structure. Our method also does not rely on weak van der Waals interactions that are sometimes used in the synthesis of nanotube mats. Furthermore, our filtration-from-suspension procedure can be readily scaled up for industrial use and does not require high pressure or high temperature reaction chambers. Such CNT-based composites can be used in a wide variety of applications. We demonstrate their use in a hydrogen sensor and a dye-sensitized solar cell.

  6. A copper-hydrogen peroxide redox system induces dityrosine cross-links and chemokine oligomerisation.

    Science.gov (United States)

    MacGregor, Helen J; Kato, Yoji; Marshall, Lindsay J; Nevell, Thomas G; Shute, Janis K

    2011-12-01

    The activity of the chemoattractant cytokines, the chemokines, in vivo is enhanced by oligomerisation and aggregation on glycosaminoglycan (GAG), particularly heparan sulphate, side chains of proteoglycans. The chemokine RANTES (CCL5) is a T-lymphocyte and monocyte chemoattractant, which has a minimum tetrameric structure for in vivo activity and a propensity to form higher order oligomers. RANTES is unusual among the chemokines in having five tyrosine residues, an amino acid susceptible to oxidative cross-linking. Using fluorescence emission spectroscopy, Western blot analysis and LCMS-MS, we show that a copper/H2O2 redox system induces the formation of covalent dityrosine cross-links and RANTES oligomerisation with the formation of tetramers, as well as higher order oligomers. Amongst the transition metals tested, namely copper, nickel, mercury, iron and zinc, copper appeared unique in this respect. At high (400 μM) concentrations of H2O2, RANTES monomers, dimers and oligomers are destroyed, but heparan sulphate protects the chemokine from oxidative damage, promoting dityrosine cross-links and multimer formation under oxidative conditions. Low levels of dityrosine cross-links were detected in copper/H2O2-treated IL-8 (CXCL8), which has one tyrosine residue, and none were detected in ENA-78 (CXCL5), which has none. Redox-treated RANTES was fully functional in Boyden chamber assays of T-cell migration and receptor usage on activated T-cells following RANTES oligomerisation was not altered. Our results point to a protective, anti-oxidant, role for heparan sulphate and a previously unrecognised role for copper in chemokine oligomerisation that may offer an explanation for the known anti-inflammatory effect of copper-chelators such as penicillamine and tobramycin.

  7. EGDMA-cross-linked polystyrene resin: An efficient support for gel phase peptide synthesis

    Indian Academy of Sciences (India)

    P K Ajikumar; K S Devaky

    2000-08-01

    This article illustrates the application of a 2% ethyleneglycol dimethacrylate-cross-linked polystyrene support (EGDMA-PS) in manual solid phase peptide synthesis. This copolymer has been characterised and optimised for peptide synthesis by performing the synthesis of a few model peptides and two biologically important peptides. EGDMA-cross-linked polystyrene support was prepared by the suspension polymerisation of the monomers EGDMA and styrene. EGDMA-PS resin undergoes facile swelling in a variety of solvents, both polar and nonpolar, used in peptide synthesis. The polymer was functionalised by Friedel-Crafts chloromethylation reaction. Peptides were assembled on a 2% cross-linked chloromethyl polymer support of capacity 1.63 mmol Cl/g. The biological peptides synthesised are an 11-residue peptide ATP binding site of the CDC2 kinase and a difficult sequence-a nineresidue peptide 34-42 corresponding to a portion of the hydrophobic terminus of the-amyloid protein 1-42. After synthesis, the peptides were cleaved from the support by treating with neat TFA. Purity of the peptides obtained in good yield was checked by TLC and HPLC methods and found to be fairly high.

  8. Application of cross-linked and hydrolyzed arabinoxylans in baking of model rye bread.

    Science.gov (United States)

    Buksa, Krzysztof; Nowotna, Anna; Ziobro, Rafał

    2016-02-01

    The role of water extractable arabinoxylan with varying molar mass and structure (cross-linked vs. hydrolyzed) in the structure formation of rye bread was examined using a model bread. Instead of the normal flour, the dough contained starch, arabinoxylan and protein, which were isolated from rye wholemeal. It was observed that the applied mixes of these constituents result in a product closely resembling typical rye bread, even if arabinoxylan was modified (by cross-linking or hydrolysis). The levels of arabinoxylan required for bread preparation depended on its modification and mix composition. At 3% protein, the maximum applicable level of poorly soluble cross-linked arabinoxylan was 3%, as higher amounts of this preparation resulted in an extensively viscous dough and diminished bread volume. On the other hand highly soluble, hydrolyzed arabinoxylan could be used at a higher level (6%) together with larger amounts of rye protein (3% or 6%). Further addition of arabinoxylan leads to excessive water absorption, resulting in a decreased viscosity of the dough during baking and insufficient gas retention. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. Capacity of cognitive radio under imperfect secondary and cross link channel state information

    KAUST Repository

    Sboui, Lokman

    2011-09-01

    In this paper, we study the ergodic capacity of secondary user channel in a spectrum sharing scenario in which the secondary transmitter is instantaneously aware of estimated versions of the cross link (between the secondary transmitter and the primary receiver) and the secondary link Channel State Information (CSI). The secondary link optimal power profile along with the ergodic capacity are derived for a class of fading channels, under an average power constraint and an instantaneous interference outage constraint. We also show that our framework is rather general as it encompasses several previously studied spectrum sharing settings as special cases. In order to gain some insights on the capacity behavior, numerical results are shown for independent Rayleigh fading channels where it is found for instance, that at low SNR regime, only the secondary channel estimation matters and that the cross link CSI has no effect on the ergodic capacity; whereas at high SNR regime, the capacity is rather driven by the cross link CSI. © 2011 IEEE.

  10. Optimizing performance in cross-linking negative-tone molecular resists

    Science.gov (United States)

    Lawson, Richard A.; Narcross, Hannah; Sharp, Brandon; Chun, Jun Sung; Neisser, Mark; Tolbert, Laren M.; Henderson, Clifford L.

    2015-03-01

    Many different types of non-traditional resist designs have shown promise for future generations of patterning, but there is a greater need for understanding and developing additives and ancillary materials for these novel resists compared to traditional polymeric positive tone systems which are quite mature. With the goal of meeting some of these needs, we carried out multiple different studies of negative tone molecular resists based on epoxide cross-linking. We have developed methods for controlling cross-linking in these materials using photo-decomposable nucleophiles (PDNs) which have shown resolution improvements in one resist from 26 nm down to 18 nm so far. Aqueous base developed systems have been made by introducing phenol groups to these resists. Although the first molecule designed successfully patterns in aqueous base, its performance is limited compared to organic solvent development. A series of di-functional epoxide molecular resists have been made and generally show much worse sensitivity than a fourfunctional epoxide resist. Underlayers (ULs) have been designed specifically to leverage the high reactivity of epoxides to create ULs that can cross-link to the resist. These ULs improve the adhesion of some of these molecular resists, but also show significant sensitivity improvements compared to imaging on bare silicon. Sensitivity in one resist was improved by 5-12 mJ/cm2 simply by using the UL.

  11. Multiple and sequential data acquisition method: an improved method for fragmentation and detection of cross-linked peptides on a hybrid linear trap quadrupole Orbitrap Velos mass spectrometer.

    Science.gov (United States)

    Rudashevskaya, Elena L; Breitwieser, Florian P; Huber, Marie L; Colinge, Jacques; Müller, André C; Bennett, Keiryn L

    2013-02-05

    The identification and validation of cross-linked peptides by mass spectrometry remains a daunting challenge for protein-protein cross-linking approaches when investigating protein interactions. This includes the fragmentation of cross-linked peptides in the mass spectrometer per se and following database searching, the matching of the molecular masses of the fragment ions to the correct cross-linked peptides. The hybrid linear trap quadrupole (LTQ) Orbitrap Velos combines the speed of the tandem mass spectrometry (MS/MS) duty circle with high mass accuracy, and these features were utilized in the current study to substantially improve the confidence in the identification of cross-linked peptides. An MS/MS method termed multiple and sequential data acquisition method (MSDAM) was developed. Preliminary optimization of the MS/MS settings was performed with a synthetic peptide (TP1) cross-linked with bis[sulfosuccinimidyl] suberate (BS(3)). On the basis of these results, MSDAM was created and assessed on the BS(3)-cross-linked bovine serum albumin (BSA) homodimer. MSDAM applies a series of multiple sequential fragmentation events with a range of different normalized collision energies (NCE) to the same precursor ion. The combination of a series of NCE enabled a considerable improvement in the quality of the fragmentation spectra for cross-linked peptides, and ultimately aided in the identification of the sequences of the cross-linked peptides. Concurrently, MSDAM provides confirmatory evidence from the formation of reporter ions fragments, which reduces the false positive rate of incorrectly assigned cross-linked peptides.

  12. Controlled delivery of valsartan by cross-linked polymeric matrices: Synthesis, in vitro and in vivo evaluation.

    Science.gov (United States)

    Sohail, Muhammad; Ahmad, Mahmood; Minhas, Muhammad Usman; Ali, Liaqat; Khalid, Ikrima; Rashid, Haroon

    2015-06-20

    The purpose of study was to develop chemically cross-linked chitosan-co-poly(AMPS) hydrogel based on low molecular weight chitosan for pH-responsive and controlled drug delivery of a model drug. Cross-linking was achieved chemically, by using free radical polymerization technique. Polymer (low molecular weight chitosan) was chemically cross-linked with monomer (2-acrylamido-2-methylpropane sulfonic acid) in aqueous medium. N, N'-Methylenebisacrylamide (MBA) was used as cross-linking agent. Sodium hydrogen sulfite (SHS) and ammonium peroxodisulphate (APS) were used as initiators in a chemical reaction. Hydrogels were characterized by FT-IR, SEM and DSC. Swelling studies and pH-sensitivity of hydrogels were studies at pH 1.2 and 7.4. Chitosan-co-poly(AMPS) hydrogels were administered to rabbits orally to evaluate its pharmacokinetic behavior. As a result of successful cross-linking of polymer and monomer, novel co-polymer has been developed, having suitable characteristics as desired for controlled release drug delivery system. Maximum swelling, drug loading and release have been observed at pH 7.4. In vivo results exhibited significant drug release and absorption at pH 7.4 in rabbits. It is concluded that highly swelling chitosan-AMPS based hydrogels were developed having pH independent swelling and pH dependent drug release properties. These hydrogels have great potential to be used for loading and controlled release of various therapeutic agents.

  13. Entrapment of methyl parathion hydrolase in cross-linked poly(γ-glutamic acid)/gelatin hydrogel.

    Science.gov (United States)

    Xie, Jianfei; Zhang, Huiwen; Li, Xu; Shi, Yuanliang

    2014-02-10

    Methyl parathion hydrolase (MPH) is an important enzyme in hydrolyzing toxic organophosphorus (OP) compounds. However, MPH is easily deactivated when subjected to extreme environmental conditions and is difficult to recover from the reaction system for reuse, thereby limiting its practical application. To address these shortcomings, we examined the entrapment of MPH in an environment-friendly, biocompatible and biodegradable cross-linked poly(γ-glutamic acid)/gelatin hydrogel. The cross-linked poly(γ-glutamic acid)/gelatin hydrogels were prepared with different gelatin/poly(γ-glutamic acid) mass ratios using water-soluble carbodiimide as the cross-linking agent. The MPH-entrapped cross-linked poly(γ-glutamic acid)/gelatin hydrogel (CPE-MPH) not only possessed improved thermostability, pH stability, and reusability but also exhibited enhanced efficiency in hydrolyzing OP compounds. Furthermore, CPE-MPH possesses high water-absorbing and water-retaining capabilities. We believe that the cross-linked poly(γ-glutamic acid)/gelatin hydrogels are an attractive carrier for the entrapment of diverse enzymes, affording a new approach for enzyme entrapment.

  14. Comparative studies on performance of radiation-induced and thermal cross-linked ion-exchange membrane for water electrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Chakrabarty, Tina; Jasti, Amaranadh [Electro-Membrane Processes Division, Central Salt and Marine Chemicals Research Institute, Council of Scientific and Industrial Research (CSIR), G. B. Marg, Bhavnagar 364002, Gujarat (India); Goel, N.K. [Radiation Technology Division, Bhabha Atomic Research Center, Trombay, Mumbai (India); Shahi, Vinod K., E-mail: vkshahi@csmcri.or [Electro-Membrane Processes Division, Central Salt and Marine Chemicals Research Institute, Council of Scientific and Industrial Research (CSIR), G. B. Marg, Bhavnagar 364002, Gujarat (India); Sabharwal, Sunil [Radiation Technology Division, Bhabha Atomic Research Center, Trombay, Mumbai (India)

    2011-07-15

    Radiation-induced and thermal cross-linked sulfonated poly(ether sulfone) (SPS)-sulfonated poly(ether ether ketone) (SPK) composite ion-exchange membranes (SPS/SPK({gamma}) and SPS/SPK(T), respectively) were prepared. Their performances for water electrolysis were comparatively assessed. Thermal cross-linked membrane (SPS/SPK(T)) showed cross-linking of part functional groups (-SO{sub 3}H) and thus deterioration in membrane conductivity. While, radiation-induced cross-linked membrane (SPS/SPK({gamma})) avoided any cross-linking between functional groups and thus conductivity. Electrolysis performances of these membranes were evaluated in comparison with Nafion117 membrane. Relatively low current efficiency (CE) for SPS/SPK and SPS/SPK(T) membranes was due to their high mass transfer (water) via electro-osmotic drag, which was negligible for SPS/SPK({gamma}) membrane. SPS/SPK({gamma}) membrane exhibited comparable stabilities and water splitting performance with Nafion117 membrane, which revealed its suitability as substitute for electrochemical applications.

  15. Comparative studies on performance of radiation-induced and thermal cross-linked ion-exchange membrane for water electrolysis

    Science.gov (United States)

    Chakrabarty, Tina; Jasti, Amaranadh; Goel, N. K.; Shahi, Vinod K.; Sabharwal, Sunil

    2011-07-01

    Radiation-induced and thermal cross-linked sulfonated poly(ether sulfone) (SPS)-sulfonated poly(ether ether ketone) (SPK) composite ion-exchange membranes (SPS/SPK(γ) and SPS/SPK(T), respectively) were prepared. Their performances for water electrolysis were comparatively assessed. Thermal cross-linked membrane (SPS/SPK(T)) showed cross-linking of part functional groups (-SO 3H) and thus deterioration in membrane conductivity. While, radiation-induced cross-linked membrane (SPS/SPK(γ)) avoided any cross-linking between functional groups and thus conductivity. Electrolysis performances of these membranes were evaluated in comparison with Nafion117 membrane. Relatively low current efficiency (CE) for SPS/SPK and SPS/SPK(T) membranes was due to their high mass transfer (water) via electro-osmotic drag, which was negligible for SPS/SPK(γ) membrane. SPS/SPK(γ) membrane exhibited comparable stabilities and water splitting performance with Nafion117 membrane, which revealed its suitability as substitute for electrochemical applications.

  16. Scleral wound healing with cross-link technique using riboflavin and ultraviolet A on rabbit eyes

    Directory of Open Access Journals (Sweden)

    Damasceno NA

    2017-07-01

    Full Text Available Nadyr A Damasceno,1 Nadia C Miguel,2 Marcelo Palis Ventura,3 Miguel Burnier Jr,4 Marcos P Avila,5 Eduardo F Damasceno3 1Ophthalmology Department, Hospital Naval Marcílio Dias, 2Laboratory of Neurohistology and Cell Ultrastructure, Instituto de Ciências Biomédicas, Universidade Federal do Rio de Janeiro, Rio de Janeiro, 3Ophthalmology Department, Universidade Federal Fluminense, Niterói, Brazil; 4Ophthalmology Department, McGill University, Montreal, QC, Canada; 5Ophthalmology Department, Universidade Federal de Goiás, Goiania, Brazil Purpose: The aim of study was to evaluate the cross-link using riboflavin and ultraviolet A (UVA for improving scleral wound healing.Materials and methods: This was an experimental study involving four New Zealand rabbits (eight eyes. Therapy procedure was chosen for the right eye and control procedure for the left one. UVA irradiation of 365 nm with a surface irradiance of 3 mW/cm2 and a photosensitizer of riboflavin drops were applied for 30 minutes on the right eye at 2 mm from the limbus. Sclerotomy incision was performed at 2 mm from the limbus in both right (on the cross-link-treated area and left eye. Then, 30 days after surgery, a morphological analysis and histological staining with hematoxylin–eosin and picrosirius red were performed, and the sclerotomy cicatrization of right and left eyes was compared. The variables investigated were as follows: sclerotomy incision pictures and measurements were made using the ImageJ Software. Scleral thickness was measured (employing the anterior optical coherence tomography and the digital caliper. Collagen fiber density stained with picrosirius red staining was measured using the Image Pro Plus software.Results: The morphological analysis showed that in all samples, the right eye presented sclerotomy closure, and in two eyes, among them, there were no visible edges of the sclerotomies incision. The left eye presented sclerotomy closure and incision edges

  17. Density limits investigation and high density operation in EAST tokamak

    Science.gov (United States)

    Zheng, Xingwei; Li, Jiangang; Hu, Jiansheng; Liu, Haiqing; Jie, Yinxian; Wang, Shouxin; Li, Jiahong; Duan, Yanming; Li, Miaohui; Li, Yongchun; Zhang, Ling; Ye, Yang; Yang, Qingquan; Zhang, Tao; Cheng, Yingjie; Xu, Jichan; Wang, Liang; Xu, Liqing; Zhao, Hailin; Wang, Fudi; Lin, Shiyao; Wu, Bin; Lyu, Bo; Xu, Guosheng; Gao, Xiang; Shi, Tonghui; He, Kaiyang; Lan, Heng; Chu, Nan; Cao, Bin; Sun, Zhen; Zuo, Guizhong; Ren, Jun; Zhuang, Huidong; Li, Changzheng; Yuan, Xiaolin; Yu, Yaowei; Wang, Houyin; Chen, Yue; Wu, Jinhua; EAST Team

    2016-05-01

    Increasing the density in a tokamak is limited by the so-called density limit, which is generally performed as an appearance of disruption causing loss of plasma confinement, or a degradation of high confinement mode which could further lead to a H  →  L transition. The L-mode and H-mode density limit has been investigated in EAST tokamak. Experimental results suggest that density limits could be triggered by either edge cooling or excessive central radiation. The L-mode density limit disruption is generally triggered by edge cooling, which leads to the current profile shrinkage and then destabilizes a 2/1 tearing mode, ultimately resulting in a disruption. The L-mode density limit scaling agrees well with the Greenwald limit in EAST. The observed H-mode density limit in EAST is an operational-space limit with a value of 0.8∼ 0.9{{n}\\text{GW}} . High density H-mode heated by neutral beam injection (NBI) and lower hybrid current drive (LHCD) are analyzed, respectively. The constancy of the edge density gradients in H-mode indicates a critical limit caused perhaps by e.g. ballooning induced transport. The maximum density is accessed at the H  →  L transition which is generally caused by the excessive core radiation due to high Z impurities (Fe, Cu). Operating at a high density (>2.8× {{10}19} {{\\text{m}}-3} ) is favorable for suppressing the beam shine through NBI. High density H-mode up to 5.3× {{10}19}{{\\text{m}}-3}~≤ft(∼ 0.8{{n}\\text{GW}}\\right) could be sustained by 2 MW 4.6 GHz LHCD alone, and its current drive efficiency is studied. Statistics show that good control of impurities and recycling facilitate high density operation. With careful control of these factors, high density up to 0.93{{n}\\text{GW}} stable H-mode operation was carried out heated by 1.7 MW LHCD and 1.9 MW ion cyclotron resonance heating with supersonic molecular beam injection fueling.

  18. Solvent effects on the physicochemical properties of the cross-linked histidine-tyrosine ligand of cytochrome c oxidase.

    Science.gov (United States)

    McDonald, William J; Einarsdóttir, Olöf

    2010-05-20

    Density functional theory was used to explore the effects of aqueous solvation on the structure, vibrational frequencies, and the electronic absorption spectrum of 2-(4-methylimidazol-1-yl)-phenol (Me-ImPhOH), a chemical analogue of the cross-linked histidine-tyrosine Cu(B) ligand of cytochrome c oxidase. In addition, the phenolic-OH pK(a), the anodic redox potential for the biring radical/anion couple, and the phenolic-OH bond dissociation energy were calculated relative to phenol using a series of isodesmic reactions. In the gas phase, the imidazole moiety stabilizes the biring anion for all the models and greatly decreases the phenolic-OH pK(a) relative to phenol. Moreover, the conductor-like polarizable continuum model (C-PCM)-water-solvated reactions predict Delta pK(a) values that are five times smaller than the gas-phase reactions, in agreement with the proposed role of the cross-linked histidine-tyrosine as a proton donor in the enzyme. For the neutral biring radical solvation models, the imidazole moiety induces a high degree of asymmetry into the phenol ring when compared to unmodified phenoxyl radical. The biring radical pi-bonds of the imidazole ring are more localized when compared to unmodified 1-methylimidazole and Me-ImPhOH solvation models, suggesting reduced aromaticity for all biring radical solvation models. The C-PCM-water-solvated reactions predict relative biring radical reduction potentials that are an order of magnitude smaller than the gas-phase reactions. The biring O-H bond is weakened relative to phenol by less than 4 kcal/mol for all the reactions studied, suggesting that the imidazole moiety does not facilitate H-atom abstraction in the enzyme. Together, these results demonstrate the sensitive nature of the proton and electron donating ability of the histidine-tyrosine cross-linked ligand in cytochrome c oxidase and suggest that for quantitative predictions of reaction energies and thermodynamic properties, models of this ligand

  19. DNA interstrand cross-linking by a mycotoxic diepoxide.

    Science.gov (United States)

    Millard, J T; Katz, J L; Goda, J; Frederick, E D; Pierce, S E; Speed, T J; Thamattoor, D M

    2004-06-01

    The diepoxide mycotoxin (2R, 3R, 8R, 9R)-4,6-decadiyne-2,3:8,9-diepoxy-1,10-diol (repandiol) was both isolated from the mushroom Hydnum repandum and synthesized de novo. Repandiol was found to form interstrand cross-links within a restriction fragment of DNA, linking deoxyguanosines on opposite strands primarily within the 5'-GNC and 5'-GNNC sequences preferred by diepoxyoctane. However, repandiol was a significantly less efficient cross-linker than either of the diepoxyalkanes (diepoxyoctane and diepoxybutane) to which it was compared.

  20. Newer protocols and future in collagen cross-linking

    Directory of Open Access Journals (Sweden)

    Arthur B Cummings

    2013-01-01

    Full Text Available Corneal Cross-Linking (CXL is an established surgical procedure for the treatment of corneal disorders such as corneal ectasia and keratoconus. This method of treatment stabilises the corneal structure and increases rigidity, reducing the requirement for corneal transplantation. Since its development, many scientific studies have been conducted to investigate ways of improving the procedure. Biomechanical stability of the cornea after exposure to UV-A light, and the effect of shortening procedure time has been some of the many topics explored

  1. Probing native protein structures by chemical cross-linking, mass spectrometry, and bioinformatics.

    Science.gov (United States)

    Leitner, Alexander; Walzthoeni, Thomas; Kahraman, Abdullah; Herzog, Franz; Rinner, Oliver; Beck, Martin; Aebersold, Ruedi

    2010-08-01

    Chemical cross-linking of reactive groups in native proteins and protein complexes in combination with the identification of cross-linked sites by mass spectrometry has been in use for more than a decade. Recent advances in instrumentation, cross-linking protocols, and analysis software have led to a renewed interest in this technique, which promises to provide important information about native protein structure and the topology of protein complexes. In this article, we discuss the critical steps of chemical cross-linking and its implications for (structural) biology: reagent design and cross-linking protocols, separation and mass spectrometric analysis of cross-linked samples, dedicated software for data analysis, and the use of cross-linking data for computational modeling. Finally, the impact of protein cross-linking on various biological disciplines is highlighted.

  2. Comparative investigation of thermal and mechanical properties of cross-linked epoxy polymers with different curing agents by molecular dynamics simulation.

    Science.gov (United States)

    Jeyranpour, F; Alahyarizadeh, Gh; Arab, B

    2015-11-01

    Molecular dynamics (MD) simulations were carried out to predict the thermal and mechanical properties of the cross-linked epoxy system composed of DGEBA resin and the curing agent TETA. To investigate the effects of curing agents, a comprehensive and comparative study was also performed on the thermal and mechanical properties of DGEBA/TETA and DGEBA/DETDA epoxy systems such as density, glass transition temperature (Tg), coefficient of thermal expansion (CTE) and elastic properties of different cross-linking densities and different temperatures. The results indicated that the glass transition temperature of DGEBA/TETA system calculated through density-temperature data, ∼ 385-395 °K, for the epoxy system with the cross-linking density of 62.5% has a better agreement with the experimental value (Tg, ∼ 400 °K) in comparison to the value calculated through the variation of cell volume in terms of temperature, 430-440 °K. They also indicated that CTE related parameters and elastic properties including Young, Bulk, and shear's moduli, and Poisson's ratio have a relative agreement with the experimental results. Comparison between the thermal and mechanical properties of epoxy systems of DGEBA/TETA and DGEBA/DETDA showed that the DGEBA/DETDA has a higher Tg in all cross linking densities than that of DGEBA/TETA, while higher mechanical properties was observed in the case of DGEBA/TETA in almost all cross linking densities.

  3. Probing the structure of human protein disulfide isomerase by chemical cross-linking combined with mass spectrometry

    DEFF Research Database (Denmark)

    Peng, Li; Rasmussen, Morten Ib; Chailyan, Anna

    2014-01-01

    Protein disulfide-isomerase (PDI) is a four-domain flexible protein that catalyzes the formation of disulfide bonds in the endoplasmic reticulum. Here we have analyzed native PDI purified from human placenta by chemical cross-linking followed by mass spectrometry (CXMS). In addition to PDI...... the sample contained soluble calnexin and ERp72. Extensive cross-linking was observed within the PDI molecule, both intra- and inter-domain, as well as between the different components in the mixture. The high sensitivity of the analysis in the current experiments, combined with a likely promiscuous...... interaction pattern of the involved proteins, revealed relatively densely populated cross-link heat maps. The established X-ray structure of the monomeric PDI could be confirmed; however, the dimer as presented in the existing models does not seem to be prevalent in solution as modeling on the observed cross...

  4. Cross-linking e segmento de anel corneano intraestromal

    Directory of Open Access Journals (Sweden)

    Adimara da Candelaria Renesto

    2011-02-01

    Full Text Available O cross-linking corneano é um procedimento usado para a estabilização mecânica e aumento da rigidez corneana em pacientes com ceratocone (reduzindo a possibilidade de progressão, e também em processos inflamatórios de afinamento corneano. Os segmentos de anéis corneanos intraestromais têm como princípio o aplanamento central da córnea. Inicialmente utilizados para correção de baixa miopia, a principal indicação atual é em pacientes com ceratocone, para melhorar a acuidade visual não corrigida, a acuidade visual corrigida e permitir uma melhor tolerância ao uso de lentes de contato como também retardar a necessidade de um transplante de córnea. O objetivo deste artigo é revisar algumas publicações relacionadas ao cross-linking corneano e à inserção do segmento de anel intraestromal, apresentando suas indicações, resultados e complicações relatadas até o momento.

  5. Fiber optic immunosensor for cross-linked fibrin concentration

    Science.gov (United States)

    Moskowitz, Samuel E.

    2000-08-01

    Working with calcium ions in the blood, platelets produce thromboplastin which transforms prothrombin into thrombin. Removing peptides, thrombin changes fibrinogen into fibrin. Cross-linked insoluble fibrin polymers are solubilized by enzyme plasmin found in blood plasma. Resulting D-dimers are elevated in patients with intravascular coagulation, deep venous thrombosis, pulmonary embolism, myocardial infarction, multiple trauma, cancer, impaired renal and liver functions, and sepsis. Consisting principally of a NIR 780 nm GaAlAs laser diode and a 800 nm avalanche photodiode (APD), the fiber-optic immunosensor can determined D-dimer concentration to levels detected by a second antibody which is labeled with NN 382 fluorescent dye. An evanescent wave traveling on an excitation optical fiber excites the antibody-antigen fluorophore complex. Concentration of cross-linked fibrin is directly proportional to the APD measured intensity of fluorescence. NIR fluorescence has advantages of low background interference, short fluorescence lifetime, and large difference between excitation and emission peaks. Competitive ELISA test for D-dimer concentration requires trained personnel performing a time consuming operation.

  6. Phosphate uptake studies of cross-linked chitosan bead materials.

    Science.gov (United States)

    Mahaninia, Mohammad H; Wilson, Lee D

    2017-01-01

    A systematic experimental study is reported that provides a molecular based understanding of cross-linked chitosan beads and their adsorption properties in aqueous solution containing phosphate dianion (HPO4(2-)) species. Synthetically modified chitosan using epichlorohydrin and glutaraldehyde cross-linkers result in surface modified beads with variable hydrophile-lipophile character and tunable HPO4(2-) uptake properties. The kinetic and thermodynamic adsorption properties of cross-linked chitosan beads with HPO4(2-) species were studied in aqueous solution. Complementary structure and physicochemical characterization of chitosan beads via potentiometry, Raman spectroscopy, DSC, and dye adsorption measurements was carried out to establish structure-property relationships. The maximum uptake (Qm) of bead systems with HPO4(2-) at equilibrium was 52.1mgg(-1); whereas, kinetic uptake results for chitosan bead/phosphate systems are relatively rapid (0.111-0.113min(-1)) with an intraparticle diffusion rate-limiting step. The adsorption process follows a multi-step pathway involving inner- and outer-sphere complexes with significant changes in hydration. Phosphate uptake strongly depends on the composition and type of cross-linker used for preparation of chitosan beads. The adsorption isotherms and structural characterization of bead systems illustrate the role of surface charge, hydrophile-lipophile balance, adsorption site accessibility, and hydration properties of the chitosan bead surface. Copyright © 2016 Elsevier Inc. All rights reserved.

  7. Adsorption of methyl orange onto protonated cross-linked chitosan

    Directory of Open Access Journals (Sweden)

    Ruihua Huang

    2017-01-01

    Full Text Available The adsorption of methyl orange (MO from aqueous solutions on protonated cross-linked chitosan was studied in a batch system. The results showed that the adsorption of MO onto protonated cross-linked chitosan was affected significantly by initial MO concentration, adsorbent dosage, adsorption temperature, and contact time. The pH value of solution had a minor impact on the adsorption of MO in a pH range of 1.0–9.1. The equilibrium isotherms at different temperatures (293, 303, and 313 K and pH values (4.5, 6.7, and 9.1 were investigated. Langmuir model was able to describe these Equilibrium data fitted perfectly. The maximum monolayer adsorption capacities obtained from the Langmuir model were 89.29, 130.9, and 180.2 mg/g at 293, 303, and 313 K, respectively. Adsorption kinetics at different concentrations (100, 200 and 300 mg/L and pH values (4.5, 6.7 and 9.1 were also studied. The kinetics was correlated well with the pseudo second-order model.

  8. Supermacroporous chemically cross-linked poly(aspartic acid) hydrogels.

    Science.gov (United States)

    Gyarmati, Benjámin; Mészár, E Zsuzsanna; Kiss, Lóránd; Deli, Mária A; László, Krisztina; Szilágyi, András

    2015-08-01

    Chemically cross-linked poly(aspartic acid) (PASP) gels were prepared by a solid-liquid phase separation technique, cryogelation, to achieve a supermacroporous interconnected pore structure. The precursor polymer of PASP, polysuccinimide (PSI) was cross-linked below the freezing point of the solvent and the forming crystals acted as templates for the pores. Dimethyl sulfoxide was chosen as solvent instead of the more commonly used water. Thus larger temperatures could be utilized for the preparation and the drawback of increase in specific volume of water upon freezing could be eliminated. The morphology of the hydrogels was characterized by scanning electron microscopy and interconnectivity of the pores was proven by the small flow resistance of the gels. Compression tests also confirmed the interconnected porous structure and the complete re-swelling and shape recovery of the supermacroporous PASP hydrogels. The prepared hydrogels are of interest for several biomedical applications as scaffolding materials because of their cytocompatibility, controllable morphology and pH-responsive character.

  9. Microbial Keratitis After Collagen Cross-linking Treatment

    Directory of Open Access Journals (Sweden)

    Banu Torun Acar

    2012-07-01

    Full Text Available A 33-year-old woman presented with pain, redness, and diminution of vision that occurred 2 days after collagen cross-linking had been performed for keratoconus in the right eye. Culture results from the patient's contact lens and corneal scrapings were positive for Staphylococcus epidermidis. According to the results of antibiotic susceptibility testing, the patient was treated with hourly topical fortified vancomycin and exocin. Before collagen cross-linking, the best-corrected visual acuity (BCVA was 4/10, the manifest refraction was -7.00 -1.755 3°. Four months after the procedure, the BCVA was 4/10, the manifest refraction was -5.50 -1.75 10°. Slit-lamp examination revealed a mild residual haze in the upper midperipheral cornea, and stromal opacities had disappeared. Collagen crosslinking is less invasive compared to other methods for treatment of keratoconus, but epithelial debridement and bandage contact lens wearing may lead to the development of bacterial keratitis. (Turk J Oph thal mol 2012; 42: 300-2

  10. Covalently Cross-Linked Arabinoxylans Films for Debaryomyces hansenii Entrapment

    Directory of Open Access Journals (Sweden)

    Ramsés González-Estrada

    2015-06-01

    Full Text Available In the present study, wheat water extractable arabinoxylans (WEAX were isolated and characterized, and their capability to form covalently cross-linked films in presence of Debaryomyces hansenii was evaluated. WEAX presented an arabinose to xylose ratio of 0.60, a ferulic acid and diferulic acid content of 2.1 and 0.04 µg∙mg−1 WEAX, respectively and a Fourier Transform Infra-Red (FT-IR spectrum typical of WEAX. The intrinsic viscosity and viscosimetric molecular weight values for WEAX were 3.6 dL∙g−1 and 440 kDa, respectively. The gelation of WEAX (1% w/v with and without D. hansenii (1 × 107 CFU∙cm−2 was rheologically investigated by small amplitude oscillatory shear. The entrapment of D. hansenii decreased gel elasticity from 1.4 to 0.3 Pa, probably by affecting the physical interactions between WEAX chains. Covalently cross-linked WEAX films containing D. hansenii were prepared by casting. Scanning electron microscopy images show that WEAX films containing D. hansenii were porous and consisted of granular-like and fibre microstructures. Average tensile strength, elongation at break and Young’s modulus values dropped when D. hansenii was present in the film. Covalently cross-lined WEAX containing D. hansenii could be a suitable as a functional entrapping film.

  11. Tea derived galloylated polyphenols cross-link purified gastrointestinal mucins.

    Directory of Open Access Journals (Sweden)

    Pantelis Georgiades

    Full Text Available Polyphenols derived from tea are thought to be important for human health. We show using a combination of particle tracking microrheology and small-angle neutron scattering that polyphenols acts as cross-linkers for purified gastrointestinal mucin, derived from the stomach and the duodenum. Both naturally derived purified polyphenols, and green and black tea extracts are shown to act as cross-linkers. The main active cross-linking component is found to be the galloylated forms of catechins. The viscosity, elasticity and relaxation time of the mucin solutions experience an order of magnitude change in value upon addition of the polyphenol cross-linkers. Similarly small-angle neutron scattering experiments demonstrate a sol-gel transition with the addition of polyphenols, with a large increase in the scattering at low angles, which is attributed to the formation of large scale (>10 nm heterogeneities during gelation. Cross-linking of mucins by polyphenols is thus expected to have an impact on the physicochemical environment of both the stomach and duodenum; polyphenols are expected to modulate the barrier properties of mucus, nutrient absorption through mucus and the viscoelastic microenvironments of intestinal bacteria.

  12. Thermal and mechanical properties of e-beam irradiated butt-fusion joint in high-density polyethylene pipes

    Science.gov (United States)

    Vijayan, Vipin; Pokharel, Pashupati; Kang, Min Kwan; Choi, Sunwoong

    2016-05-01

    The effects of electron beam irradiation on the thermal and mechanical properties of a butt-fusion joint in high density polyethylene (HDPE) pipes were investigated. Differential scanning calorimetry, X-ray diffraction, and Fourier transform infra-red spectroscopy of welded samples revealed the changes of crystallinity due to the cross linking effect of electron beam irradiation. The suppression of the degree of crystallinity with increasing the irradiation dose from 0 kGy to 500 kGy indicated that the e-beam radiation induced cross-links among the polymer chains at the weld zone. The cross-link junction at the joint of HDPE pipe prevented chain folding and reorganization leading to the formation of imperfect crystallites with smaller size and also less in content. Tensile test of the welded samples with different dose of e-beam irradiation showed the increased values of the yield stress and Young's modulus as a function of irradiation dose. On the other hand, the elongation at break diminished clearly with increasing the irradiation doses.

  13. Thermally Cross-Linked Anion Exchange Membranes from Solvent Processable Isoprene Containing Ionomers

    Science.gov (United States)

    2015-01-15

    capacities (IECs). Solution cast membranes were thermally cross- linked to form anion exchange membranes. Cross-linking was achieved by taking advantage...distribution is unlimited. Thermally Cross-Linked Anion Exchange Membranes from Solvent Processable Isoprene Containing Ionomers The views...Box 12211 Research Triangle Park, NC 27709-2211 Anion Exchnage Membrane, Polymer synthesis, Morphology, Anion Conductivity REPORT DOCUMENTATION PAGE

  14. Small Strain Topological Effects of Biopolymer Networks with Rigid Cross-Links

    NARCIS (Netherlands)

    Zagar, G.; Onck, P. R.; Van der Giessen, E.; Garikipati, K; Arruda, EM

    2010-01-01

    Networks of cross-linked filamentous biopolymers form topological structures characterized by L, T and X cross-link types of connectivity 2, 3 and 4, respectively. The distribution of cross-links over these three types proofs to be very important for the initial elastic shear stiffness of isotropic

  15. Cross-linking of dermal sheep collagen using a water-soluble carbodiimide

    NARCIS (Netherlands)

    Olde Damink, L.H.H.; Dijkstra, P.J.; Luyn, van M.J.A.; Wachem, van P.B.; Nieuwenhuis, P.; Feijen, J.

    1996-01-01

    A cross-linking method for collagen-based biomaterials was developed using the water-soluble carbodiimide 1-ethyl-3-(3-dimethyl aminopropyl)carbodiimide hydrochloride (EDC). Cross-linking using EDC involves the activation of carboxylic acid groups to give O-acylisourea groups, which form cross-links

  16. In situ cross-linked electrospun fiber scaffold of collagen for fabricating cell-dense muscle tissue.

    Science.gov (United States)

    Takeda, Naoya; Tamura, Kenichi; Mineguchi, Ryo; Ishikawa, Yumiko; Haraguchi, Yuji; Shimizu, Tatsuya; Hara, Yusuke

    2016-06-01

    Engineered muscle tissues used as transplant tissues in regenerative medicine should have a three-dimensional and cell-dense structure like native tissue. For fabricating a 3D cell-dense muscle tissue from myoblasts, we proposed the electrospun type I collagen microfiber scaffold of the string-shape like a harp. The microfibers were oriented in the same direction to allow the myoblasts to align, and were strung at low density with micrometer intervals to create space for the cells to occupy. To realize this shape of the scaffold, we employed in situ cross-linking during electrospinning process for the first time to collagen fibers. The collagen microfibers in situ cross-linked with glutaraldehyde stably existed in the aqueous media and completely retained the original shape to save the spaces between the fibers for over 14 days. On the contrary, the conventional cross-linking method by exposure to a glutaraldehyde aqueous solution vapor partially dissolved and damaged the fiber to lose a low-density shape of the scaffold. Myoblasts could penetrate into the interior of the in situ cross-linked string-shaped scaffold and form the cell-dense muscle tissues. Histochemical analysis showed the total area occupied by the cells in the cross section of the tissue was approximately 73 %. Furthermore, the resulting muscle tissue fabricated from primary myoblasts showed typical sarcomeric cross-striations and the entire tissue continuously pulsated by autonomous contraction. Together with the in situ cross-linking, the string-shaped scaffold provides an efficient methodology to fabricate a cell-dense 3D muscle tissue, which could be applied in regenerative medicine in future.

  17. PERVAPORATION PROPERTIES OF PDMS MEMBRANES CURED WITH DIFFERENT CROSS-LINKING REAGENTS FOR ETHANOL CONCENTRATION FROM AQUEOUS SOLUTIONS

    Institute of Scientific and Technical Information of China (English)

    Xia Zhan; Ji-ding Li; Jun-qi Huang; Cui-xian Chen

    2009-01-01

    Ethanol perm-selective PDMS/PVDF composite membranes were prepared by curing polydimethylsiloxane (PDMS) with various cross-linking reagents, such as tetraethoxylsilane (TEOS), γ-aminopropyltriethoxylsilane (APTEOS), phenyltrimethoxylsilane (PTMOS) and octyltrimethoxylsilane (OTMOS) as well. The cross-linking density and surface properties of the PDMS active layer were adjusted by varying cross-linking reagents. The pervaporation performance of PDMS membranes cured with different cross-linking reagents was investigated in detail. As temperature increased, the total flux of the four kinds of membranes all increased exponentially, and the separation factor followed a reversed order. The increase of thickness of PDMS layers depressed the total flux of composite membranes and had no obvious effect on selectivity of ethanol. It was found that the composite membrane cured by PTMOS showed much better separation performance compared with other membranes. A resistance-in-series model was used to investigate and estimate the overall mass transfer coefficients and boundary layer mass transfer coefficients of ethanol and water according to experimental results. The measured diffusivities of ethanol and water in PDMS membranes had a magnitude of 10-10 m2·s-1 and 10-11 m2·s-1 at 313.15 K, respectively.

  18. Surface-gradient cross-linked polyethylene acetabular cups: oxidation resistance and wear against smooth and rough femoral balls.

    Science.gov (United States)

    Shen, Fu-Wen; McKellop, Harry

    2005-01-01

    Two methods were developed and evaluated for cross-linking the bearing surface of a polyethylene acetabular cup to a limited depth, in order to improve its resistance to wear without degrading the mechanical properties of the bulk of the component. In the first method, low-energy electron beams were used to cross-link only the bearing surface of the cups to a maximum depth of about 2 mm. The cups then were annealed at 100 degrees C in vacuum for 3 or 6 days to reduce the residual free radicals, and the resultant resistance to oxidation was compared by artificially aging the cups at 80 degrees C in air. Chemically cross-linked surface layers were produced by coating the bearing surfaces of the cups with a thin layer of polyethylene powder mixed with 1% weight peroxide, and compressing them at 6.9 MPa (1000 psi) and 170 degrees C. This resulted in a cross-linked surface layer that extended about 3 mm deep, with a gradual transition to conventional (noncross-linked) polyethylene in the bulk of the implant. In hip simulator wear tests with highly polished (implant quality) femoral balls, both types of surface cross-linking were found to improve markedly the wear resistance of the acetabular cups. In tests with roughened femoral balls, the wear rates were much higher and were comparable to those obtained with similarly roughened balls against noncross-linked polyethylene cups in a previous study, indicating that the full benefit of cross-linking may not be realized under conditions of severe third-body abrasion. Nevertheless, these results show a promising approach for optimizing the wear resistance and the bulk mechanical properties of polyethylene components in total joint arthroplasty.

  19. Determination of the relationship between collagen cross-links and the bone-tissue stiffness in the porcine mandibular condyle.

    Science.gov (United States)

    Willems, Nop M B K; Mulder, Lars; Bank, Ruud A; Grünheid, Thorsten; den Toonder, Jaap M J; Zentner, Andrej; Langenbach, Geerling E J

    2011-04-07

    Although bone-tissue stiffness is closely related to the degree to which bone has been mineralized, other determinants are yet to be identified. We, therefore, examined the extent to which the mineralization degree, collagen, and its cross-links are related to bone-tissue stiffness. A total of 50 cancellous and cortical bone samples were derived from the right mandibular condyles of five young and five adult female pigs. The degree of mineralization of bone (DMB) was assessed using micro-computed tomography. Using high-performance liquid chromatography, we quantified the collagen content and the number of cross-links per collagen molecule of two enzymatic cross-links: hydroxylysylpyridinoline (HP) and lysylpyridinoline (LP), and one non-enzymatic cross-link: pentosidine (Pen). Nanoindentation was used to assess bone-tissue stiffness in three directions, and multiple linear regressions were used to calculate the correlation between collagen properties and bone-tissue stiffness, with the DMB as first predictor. Whereas the bone-tissue stiffness of cancellous bone did not differ between the three directions of nanoindentation, or between the two age groups, cortical bone-tissue stiffness was higher in the adult tissue. After correction for DMB, the cross-links studied did not increase the explained variance. In the young group, however, LP significantly improved the explained variance in bone-tissue stiffness. Approximately half of the variation in bone-tissue stiffness in cancellous and cortical bone was explained by the DMB and the LP cross-links and thus they cannot be considered the sole determinants of the bone-tissue stiffness.

  20. Biocatalytic cross-linking of pectic polysaccharides for designed food functionality

    DEFF Research Database (Denmark)

    Zaidel, Dayang Norulfairuz Abang; Meyer, Anne S.

    2012-01-01

    Recent research has demonstrated how cross-linking of pectic polysaccharides to obtain gel formation can be promoted by enzymatic catalysis reactions, and provide opportunities for functional upgrading of pectic polysaccharides present in agro-industrial sidestreams. This review highlights...... the mechanisms of formation of functional pectic polysaccharide cross-links, including covalent cross-links (notably phenolic esters and uronyl ester linkages) and non-covalent, ionic cross-links (which involve calcium and borate ester links). The treatise examines how such cross-links can be designed via...

  1. Induction and repair of DNA cross-links induced by sulfur mustard in the A-549 cell line followed by a comet assay.

    Science.gov (United States)

    Jost, Petr; Svobodova, Hana; Stetina, Rudolf

    2015-07-25

    Sulfur mustard is a highly toxic chemical warfare agent with devastating impact on intoxicated tissues. DNA cross-links are probably the most toxic DNA lesions induced in the cell by sulfur mustard. The comet assay is a very sensitive method for measuring DNA damage. In the present study using the A-549 lung cell line, the comet assay protocol was optimized for indirect detection of DNA cross-links induced by sulfur mustard. The method is based on the additional treatment of the assayed cells containing cross-links with the chemical mutagen, styrene oxide. Alkali-labile adducts of styrene oxide cause DNA breaks leading to the formation of comets. A significant dose-dependent reduction of DNA migration of the comet's tail was found after exposing cells to sulfur mustard, indicative of the amount of sulfur mustard induced cross-links. The remarkable decrease of % tail DNA could be observed as early as 5min following exposure to sulfur mustard and the maximal effect was found after 30min, when DNA migration was reduced to the minimum. Sulfur mustard preincubated in culture medium without cells lost its ability to induce cross-links and had a half-life of about 15min. Pre-incubation longer than 30min does not lead to a significant increase in cross-links when applied to cells. However, the amount of cross-links is decreased during further incubation due to repair. The current modification of the comet assay provides a useful tool for detecting DNA cross-links induced by sulfur mustard and could be used for detection of other DNA cross-linking agents such as chemotherapeutic drugs.

  2. High-density lipoprotein cholesterol: How High

    Directory of Open Access Journals (Sweden)

    G Rajagopal

    2012-01-01

    Full Text Available The high-density lipoprotein cholesterol (HDL-C is considered anti-atherogenic good cholesterol. It is involved in reverse transport of lipids. Epidemiological studies have found inverse relationship of HDL-C and coronary heart disease (CHD risk. When grouped according to HDL-C, subjects having HDL-C more than 60 mg/dL had lesser risk of CHD than those having HDL-C of 40-60 mg/dL, who in turn had lesser risk than those who had HDL-C less than 40 mg/dL. No upper limit for beneficial effect of HDL-C on CHD risk has been identified. The goals of treating patients with low HDL-C have not been firmly established. Though many drugs are known to improve HDL-C concentration, statins are proven to improve CHD risk and mortality. Cholesteryl ester transfer protein (CETP is involved in metabolism of HDL-C and its inhibitors are actively being screened for clinical utility. However, final answer is still awaited on CETP-inhibitors.

  3. Stiffening of semiflexible biopolymers and cross-linked networks

    CERN Document Server

    Van Dillen, T; Van der Giessen, E

    2006-01-01

    We study the mechanical stiffening behavior in two-dimensional (2D) cross-linked networks of semiflexible biopolymer filaments under simple shear. Filamental constituents immersed in a fluid undergo thermally excited bending motions. Pulling out these undulations results in an increase in the axial stiffness. We analyze this stiffening behavior of 2D semiflexible filaments in detail: we first investigate the average, {static} force-extension relation by considering the initially present undulated configuration that is pulled straight under a tensile force, and compare this result with the average response in which undulation dynamics is allowed during pulling, as derived earlier by MacKintosh and coworkers. We will show that the resulting mechanical behavior is rather similar, but with the axial stiffness being a factor 2 to 4 larger in the dynamic model. Furthermore, we study the stretching contribution in case of extensible filaments and show that, for 2D filaments, the mechanical response is dominated by {...

  4. Swelling properties of cross-linked DNA gels.

    Science.gov (United States)

    Costa, Diana; Miguel, M Graça; Lindman, Björn

    2010-07-12

    This work represents our contribution to the field of physical chemistry of DNA gels, and concerns the synthesis and study of novel chemically cross-linked DNA gels. The use of covalent DNA gels is a very promising way to study DNA-cosolute interactions, as well as the dynamic behaviour of DNA and cationic compacting agents, like lipids, surfactants and polycations. Manipulating DNA in new ways, like DNA networks, allows a better understanding and characterization of DNA-cosolute complexes at the molecular level, and also allows us to follow the assembly structures of these complexes. The use of responsive polymer gels for targeted delivery of toxic and/or labile drugs has, during the past few years, shown to be a promising concept. The features found in the proposed system would find applications in a broader field of gel/drug interaction, for the development of controlled release and targeted delivery devices.

  5. Conventional Versus Cross-Linked Polyethylene for Total Hip Arthroplasty.

    Science.gov (United States)

    Surace, Michele F; Monestier, Luca; Vulcano, Ettore; Harwin, Steven F; Cherubino, Paolo

    2015-09-01

    The clinical and radiographic outcomes of 88 patients who underwent primary total hip arthroplasty with either conventional polyethylene or cross-linked polyethylene (XLPE) from the same manufacturer were compared. There were no significant differences between the 2 subpopulations regarding average age, gender, side affected, or prosthetic stem and cup size. The average follow-up was 104 months (range, 55 to 131 months). To the authors' knowledge, this is the longest follow-up for this particular insert. Clinical and radiographic evaluations were performed at 1, 3, 6, and 12 months and then annually. Results showed that XLPE has a significantly greater wear reduction than that of standard polyethylene in primary total hip arthroplasty. At the longest available follow-up for these specific inserts, XLPE proved to be effective in reducing wear.

  6. Studies on N-vinylformamide cross-linked copolymers

    Science.gov (United States)

    Świder, Joanna; Tąta, Agnieszka; Sokołowska, Katarzyna; Witek, Ewa; Proniewicz, Edyta

    2015-12-01

    Copolymers of N-vinylformamide (NVF) cross-linked with three multifunctional monomers, including divinylbenzene (DVB), ethylene glycol dimethacrylate (EGDMA), and N,N‧-methylenebisacrylamide (MBA) were synthetized by a three-dimensional free radical polymerization in inverse suspension using 2,2‧-azobis(2-methylpropionamide) dihydrochloride (AIBA) as an initiator. Methyl silicon oil was used as the continuous phase during the polymerization processes. Fourier-transform adsorption infrared (FT-IR) spectra revealed the presence of silicone oil traces and suggested that silicone oil strongly interacted with the copolymers surface. Purification procedure allowed to completely remove the silicon oil traces from P(NVF-co-DVB) only. The morphology and the structure of the investigated copolymers were examined by optical microscopy, FT-IR, and FT-Raman (Fourier-transform Raman spectroscopy) methods.

  7. Non-cross-linked polystyrene-supported 2-imidazolidinone chiral auxiliary: synthesis and application in asymmetric alkylation reactions

    Science.gov (United States)

    Nguyen, Quynh Pham Bao

    2013-01-01

    Summary Asymmetric alkylation reactions using non-cross-linked polystyrene (NCPS)-supported 2-imidazolidinone chiral auxiliaries were successfully investigated with excellent diastereocontrol (>99% de). The recovery and the recycling of this soluble polymer-supported chiral auxiliary were achieved in order to produce highly optical pure carboxylic acids. PMID:24204423

  8. Utilizing Mechanistic Cross-Linking Technology to Study Protein-Protein Interactions: An Experiment Designed for an Undergraduate Biochemistry Lab

    Science.gov (United States)

    Finzel, Kara; Beld, Joris; Burkart, Michael D.; Charkoudian, Louise K.

    2017-01-01

    Over the past decade, mechanistic cross-linking probes have been used to study protein-protein interactions in natural product biosynthetic pathways. This approach is highly interdisciplinary, combining elements of protein biochemistry, organic chemistry, and computational docking. Herein, we described the development of an experiment to engage…

  9. Cross-linked polyvinyl pyridine coated glass particle catalyst support and aqueous composition or polyvinyl pyridine adducted microspheres

    Science.gov (United States)

    Rembaum, Alan (Inventor); Gupta, Amitava (Inventor); Volksen, Willi (Inventor)

    1981-01-01

    Microspheres are produced by cobalt gamma radiation initiated polymerization of a dilute aqueous vinyl pyridine solution. Addition of cross-linking agent provides higher surface area beads. Addition of monomers such as hydroxyethylmethacrylate acrylamide or methacrylamide increases hydrophilic properties and surface area of the beads. High surface area catalytic supports are formed in the presence of controlled pore glass substrate.

  10. Grass Cell Walls: A Story of Cross-Linking

    Science.gov (United States)

    Hatfield, Ronald D.; Rancour, David M.; Marita, Jane M.

    2017-01-01

    Cell wall matrices are complex composites mainly of polysaccharides, phenolics (monomers and polymers), and protein. We are beginning to understand the synthesis of these major wall components individually, but still have a poor understanding of how cell walls are assembled into complex matrices. Valuable insight has been gained by examining intact components to understand the individual elements that make up plant cell walls. Grasses are a prominent group within the plant kingdom, not only for their important roles in global agriculture, but also for the complexity of their cell walls. Ferulate incorporation into grass cell wall matrices (C3 and C4 types) leads to a cross-linked matrix that plays a prominent role in the structure and utilization of grass biomass compared to dicot species. Incorporation of p-coumarates as part of the lignin structure also adds to the complexity of grass cell walls. Feruoylation results in a wall with individual hemicellulosic polysaccharides (arabinoxylans) covalently linked to each other and to lignin. Evidence strongly suggests that ferulates not only cross-link arabinoxylans, but may be important factors in lignification of the cell wall. Therefore, the distribution of ferulates on arabinoxylans could provide a means of structuring regions of the matrix with the incorporation of lignin and have a significant impact upon localized cell wall organization. The role of other phenolics in cell wall formation such as p-coumarates (which can have concentrations higher than ferulates) remains unknown. It is possible that p-coumarates assist in the formation of lignin, especially syringyl rich lignin. The uniqueness of the grass cell wall compared to dicot sepcies may not be so much in the gross composition of the wall, but how the distinctive individual components are organized into a functional wall matrix. These features are discussed and working models are provided to illustrate how changing the organization of feruoylation and p

  11. Peptidoglycan Cross-Linking in Glycopeptide-Resistant Actinomycetales

    Science.gov (United States)

    Hugonnet, Jean-Emmanuel; Haddache, Nabila; Veckerlé, Carole; Dubost, Lionel; Marie, Arul; Shikura, Noriyasu; Mainardi, Jean-Luc; Rice, Louis B.

    2014-01-01

    Synthesis of peptidoglycan precursors ending in d-lactate (d-Lac) is thought to be responsible for glycopeptide resistance in members of the order Actinomycetales that produce these drugs and in related soil bacteria. More recently, the peptidoglycan of several members of the order Actinomycetales was shown to be cross-linked by l,d-transpeptidases that use tetrapeptide acyl donors devoid of the target of glycopeptides. To evaluate the contribution of these resistance mechanisms, we have determined the peptidoglycan structure of Streptomyces coelicolor A(3)2, which harbors a vanHAX gene cluster for the production of precursors ending in d-Lac, and Nonomuraea sp. strain ATCC 39727, which is devoid of vanHAX and produces the glycopeptide A40296. Vancomycin retained residual activity against S. coelicolor A(3)2 despite efficient incorporation of d-Lac into cytoplasmic precursors. This was due to a d,d-transpeptidase-catalyzed reaction that generated a stem pentapeptide recognized by glycopeptides by the exchange of d-Lac for d-Ala and Gly. The contribution of l,d-transpeptidases to resistance was limited by the supply of tetrapeptide acyl donors, which are essential for the formation of peptidoglycan cross-links by these enzymes. In the absence of a cytoplasmic metallo-d,d-carboxypeptidase, the tetrapeptide substrate was generated by hydrolysis of the C-terminal d-Lac residue of the stem pentadepsipeptide in the periplasm in competition with the exchange reaction catalyzed by d,d-transpeptidases. In Nonomuraea sp. strain ATCC 39727, the contribution of l,d-transpeptidases to glycopeptide resistance was limited by the incomplete conversion of pentapeptides into tetrapeptides despite the production of a cytoplasmic metallo-d,d-carboxypeptidase. Since the level of drug production exceeds the level of resistance, we propose that l,d-transpeptidases merely act as a tolerance mechanism in this bacterium. PMID:24395229

  12. Anisotropic Thermal Conductivity Measurements on Cross-Linked Polybutadienes in Uniaxial Elongation

    Science.gov (United States)

    Venerus, David C.; Kolev, Dimitre

    2008-07-01

    Cross-linked elastomers have numerous applications including automobiles, sporting goods, and biomedical devices. During both their processing and application, these materials experience large mechanical stresses and thermal gradients. In this study, we investigate the mechanical and thermal transport behavior of cross-linked polybutadienes. These materials have been prepared by cross linking well-entangled polybutadienes using an organic peroxide cross-linking agent at low concentration. Samples obtained after nearly complete conversion of the cross-linking agent, which can be characterized as lightly cross-linked (i.e., more than 10 entanglements per cross-link), were subjected to a series of large strain, uniaxial deformations. Measurements of the tensile stress and two components of the thermal conductivity tensor will be reported as a function of elongation. These data are also used to examine the stress-thermal rule in which the stress and thermal conductivity tensors are linearly related.

  13. Effects of Composition of Iron-Cross-Linked Alginate Hydrogels for Cultivation of Human Dermal Fibroblasts

    Directory of Open Access Journals (Sweden)

    Ikuko Machida-Sano

    2012-01-01

    Full Text Available We investigated the suitability of ferric-ion-cross-linked alginates (Fe-alginate with various proportions of L-guluronic acid (G and D-mannuronic acid (M residues as a culture substrate for human dermal fibroblasts. High-G and high-M Fe-alginate gels showed comparable efficacy in promoting initial cell adhesion and similar protein adsorption capacities, but superior cell proliferation was observed on high-G than on high-M Fe-alginate as culture time progressed. During immersion in culture medium, high-G Fe-alginate showed little change in gel properties in terms of swelling and polymer content, but the properties of high-M Fe-alginate gel were altered due to loss of ion cross-linking. However, the degree of cell proliferation on high-M Fe-alginate gel was improved after it had been stabilized by immersion in culture medium until no further changes occurred. These results suggest that the mode of cross-linkage between ferric ions and alginate differs depending on alginate composition and that the major factor giving rise to differences in cell growth on the two types of Fe-alginate films is gel stability during culture, rather than swelling of the original gel, polymer content, or protein adsorption ability. Our findings may be useful for extending the application of Fe-alginate to diverse biomedical fields.

  14. Mass spectrometric analysis of a UV-cross-linked protein-DNA complex: tryptophans 54 and 88 of E. coli SSB cross-link to DNA

    DEFF Research Database (Denmark)

    Steen, H; Petersen, J; Mann, M

    2001-01-01

    Protein-nucleic acid complexes are commonly studied by photochemical cross-linking. UV-induced cross-linking of protein to nucleic acid may be followed by structural analysis of the conjugated protein to localize the cross-linked amino acids and thereby identify the nucleic acid binding site. Mass....... coli single-stranded DNA binding protein (SSB) that was UV-cross-linked to a 5-iodouracil containing DNA oligomer. Two methods were optimized to circumvent the need for standard liquid chromatography and gel electrophoresis, thereby dramatically increasing the overall sensitivity of the analysis....... Enzymatic degradation of protein and oligonucleotide was combined with miniaturized sample preparation methods for enrichment and desalting of cross-linked peptide-nucleic acid heteroconjugates from complex mixtures prior to mass spectrometric analysis. Detailed characterization of the peptidic component...

  15. Neutron scattering and ab initio molecular dynamics study of cross-linking in biomedical phosphate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Parsons, A J; Ahmed, I; Rudd, C D [Division of Materials, Mechanics and Structures, Faculty of Engineering, University of Nottingham, Nottingham NG7 2RD (United Kingdom); Cuello, G J; Pellegrini, E; Richard, D; Johnson, M R, E-mail: andrew.parsons@nottingham.ac.uk [Institut Laue-Langevin, BP 156, 38042 Grenoble (France)

    2010-12-08

    Details of the microscopic structure of phosphate glasses destined for biomedical applications, which include sodium, magnesium and calcium cations, have been obtained from the static structure factor measured by means of neutron scattering. A complementary, molecular dynamics study has been performed on a range of phosphate glasses using density functional theory methods, which allow structural fluctuations, including bond breaking, in the liquid phase before quenching to the glass phase. Good agreement between experiment and simulation allows the molecular dynamics trajectories to be analysed in detail. In particular, attention is focused on the cross-linking of divalent cations in contrast with the structural aspects associated with monovalent cations. Magnesium cations are found equidistant and bridging between the phosphorus atoms of different phosphate chains, leading to a shorter phosphorus-phosphorus second neighbour distance (that is, a more compact packing of neighbouring phosphate chains) compared to the effect of sodium cations. Calcium cations show behaviour intermediate between those of magnesium and sodium. Molecular dynamics simulations give access to the cation mobility, which is lowest for magnesium, reflecting its structural, cross-linking role.

  16. Oligo(ethylene glycol)-sidechain microgels prepared in absence of cross-linking agent: Polymerization, characterization and variation of particle deformability.

    Science.gov (United States)

    Welsch, Nicole; Lyon, L Andrew

    2017-01-01

    We present a systematic study of self-cross-linked microgels formed by precipitation polymerization of oligo ethylene glycol methacrylates. The cross-linking density of these microgels and, thus, the network flexibility can be easily tuned through the modulation of the reaction temperature during polymerization. Microgels prepared in absence of any difunctional monomer, i.e. cross-linker, show enhanced deformability and particle spreading on solid surfaces as compared to microgels cross-linked with varying amounts of poly(ethylene glycol diacrylate) (PEG-DA) in addition to self-crosslinking. Particles prepared at low reaction temperatures exhibit the highest degree of spreading due to the lightly cross-linked and flexible polymer network. Moreover, AFM force spectroscopy studies suggest that cross-linker-free microgels constitute of a more homogeneous polymer network than PEG-DA cross-linked particles and have elastic moduli at the particle apex that are ~5 times smaller than the moduli of 5 mol-% PEG-DA cross-linked microgels. Resistive pulse sensing experiments demonstrate that microgels prepared at 75 and 80°C without PEG-DA are able to deform significantly to pass through nanopores that are smaller than the microgel size. Additionally, we found that polymer network flexibility of microgels is a useful tool to control the formation of particle dewetting patterns. This offers a promising new avenue for build-up of 2D self-assembled particle structures with patterned chemical and mechanical properties.

  17. Self-reinforcement and protein sustained delivery of hyaluronan hydrogel by tailoring a dually cross-linked network

    Energy Technology Data Exchange (ETDEWEB)

    Luo, Chunhong; Xu, Guoguang; Wang, Xinghui [Department of Materials Science and Engineering, College of Science and Engineering, Jinan University, Guangzhou 510632 (China); Tu, Mei; Zeng, Rong; Rong, Jianhua [Department of Materials Science and Engineering, College of Science and Engineering, Jinan University, Guangzhou 510632 (China); Engineering Research Center of Artificial Organs and Materials, Ministry of Education, Guangzhou 510632 (China); Zhao, Jianhao, E-mail: jhzhao@jnu.edu.cn [Department of Materials Science and Engineering, College of Science and Engineering, Jinan University, Guangzhou 510632 (China); Engineering Research Center of Artificial Organs and Materials, Ministry of Education, Guangzhou 510632 (China)

    2015-01-01

    A series of self-reinforcing hyaluronan hydrogels were developed to improve mechanical properties and protein sustained delivery thanks to a dually cross-linked network. Hyaluronan gel particles (HGPs, 1–5 μm in diameter) with different cross-linking densities, i.e. HGPs-1.5, HGPs-3 and HGPs-15, were prepared in an inverse emulsion system and used as the reinforcing phase after glycidyl methacrylation, while glycidyl methacrylated hyaluronan with a substitution degree of 45.2% was synthesized as the matrix phase. These two phases were cross-linked under ultraviolet irradiation to form self-reinforcing hyaluronan hydrogels (srHAs) that showed typical cross-linked structure of HGPs connecting the matrix phase by cross-section observation. In comparison to hyaluronan bulk gels and their blends with HGPs, srHAs distinctly enhanced the mechanical properties and BSA long-term sustained delivery, especially srHA-1.5 showed the highest compressive modulus of 220 ± 15 kPa and the slowest BSA delivery (67% release at 14 d). The 3T3 fibroblast cell culture showed that all the srHAs had no cytotoxicity. - Highlights: • New self-reinforcing HA hydrogels with a dually cross-linked network were developed. • Self-reinforcing HA hydrogels greatly enhanced the mechanical properties. • Self-reinforcing HA hydrogels prolonged the sustained delivery of BSA. • The self-reinforcing mechanism and BSA diffusion mechanism were discussed. • Self-reinforcing HA hydrogels had no cytotoxicity to 3T3 fibroblast cells.

  18. Characterization of Cross-linked Alkaline Lignin/Poly (Vinyl Alcohol Film with a Formaldehyde Cross-linker

    Directory of Open Access Journals (Sweden)

    Ling Su

    2014-06-01

    Full Text Available On the basis of previous experiments, industrial alkaline lignin/poly (vinyl alcohol (PVOH cross-linked films, industrial alkaline lignin/poly (vinyl alcohol blend films, and neat poly (vinyl alcohol films were prepared by casting. The films were investigated by Fourier transform infra-red spectroscopy (FTIR, X-ray diffraction (XRD, thermogravimetry analysis (TGA, and dynamic mechanical analysis (DMA. The water contact angles for the three kinds of films were studied as well. The crosslinking reaction between alkaline lignin and PVOH was strong, which was attributed to the high hydrolysis degree of PVOH and the high reactivity of formaldehyde. Compared with the neat PVOH film, the crystallinity of the cross-linked film decreased slightly; the thermal stability of the cross-linked film was higher; DMA analysis showed that the Tg and the tanδ magnitude of the alkaline lignin/PVOH reaction film both decreased slightly. Lignin and the cross-linking reaction both improved the water resistance of films. Therefore, this research has provided a detailed analysis of the characterization of the films while exploring the potential of direct usage of industrial alkaline lignin in polymer materials.

  19. Plasmodium falciparum liver stage antigen-1 is cross-linked by tissue transglutaminase

    Directory of Open Access Journals (Sweden)

    Doerig Christian

    2011-01-01

    Full Text Available Abstract Background Plasmodium falciparum sporozoites injected by mosquitoes into the blood rapidly enter liver hepatocytes and undergo pre-erythrocytic developmental schizogony forming tens of thousands of merozoites per hepatocyte. Shortly after hepatocyte invasion, the parasite starts to produce Liver Stage Antigen-1 (LSA-1, which accumulates within the parasitophorous vacuole surrounding the mass of developing merozoites. The LSA-1 protein has been described as a flocculent mass, but its role in parasite development has not been determined. Methods Recombinant N-terminal, C-terminal or a construct containing both the N- and C- terminal regions flanking two 17 amino acid residue central repeat sequences (LSA-NRC were subjected to in vitro modification by tissue transglutaminase-2 (TG2 to determine if cross-linking occurred. In addition, tissue sections of P. falciparum-infected human hepatocytes were probed with monoclonal antibodies to the isopeptide ε-(γ-glutamyllysine cross-bridge formed by TG2 enzymatic activity to determine if these antibodies co-localized with antibodies to LSA-1 in the growing liver schizonts. Results This study identified a substrate motif for (TG2 and a putative casein kinase 2 phosphorylation site within the central repeat region of LSA-1. The function of TG2 is the post-translational modification of proteins by the formation of a unique isopeptide ε-(γ-glutamyllysine cross-bridge between glutamine and lysine residues. When recombinant LSA-1 protein was crosslinked in vitro by purified TG2 in a calcium dependent reaction, a flocculent mass of protein was formed that was highly resistant to degradation. The cross-linking was not detectably affected by phosphorylation with plasmodial CK2 in vitro. Monoclonal antibodies specific to the very unique TG2 catalyzed ε- lysine cross-bridge co-localized with antibodies to LSA-1 in infected human hepatocytes providing visual evidence that LSA-1 was cross-linked in vivo

  20. Importing low-density ideas to high-density revitalisation

    DEFF Research Database (Denmark)

    Anrholtz, Jens; Ibsen, Christian Lyhne; Ibsen, Flemming

    2016-01-01

    Why did union officials from a high-union-density country like Denmark choose to import an organising strategy from low-density countries such as the US and the UK? Drawing on in-depth interviews with key union officials and internal documents, the authors of this article argue two key points. Fi...... cherry-pick some elements while leaving fundamental aspects out. The study nevertheless indicates that a lack of coherency and model-fit to Danish industrial relations might hamper the positive effects of the organising strategy....

  1. High Energy Density Capacitors Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Capacitor size and reliability are often limiting factors in pulse power, high speed switching, and power management and distribution (PMAD) systems. T/J...

  2. Characterization of Interstrand DNA-DNA Cross-Links Using the α-Hemolysin Protein Nanopore.

    Science.gov (United States)

    Zhang, Xinyue; Price, Nathan E; Fang, Xi; Yang, Zhiyu; Gu, Li-Qun; Gates, Kent S

    2015-12-22

    Nanopore-based sensors have been studied extensively as potential tools for DNA sequencing, characterization of epigenetic modifications such as 5-methylcytosine, and detection of microRNA biomarkers. In the studies described here, the α-hemolysin protein nanopore embedded in a lipid bilayer was used for the detection and characterization of interstrand cross-links in duplex DNA. Interstrand cross-links are important lesions in medicinal chemistry and toxicology because they prevent the strand separation that is required for read-out of genetic information from DNA in cells. In addition, interstrand cross-links are used for the stabilization of duplex DNA in structural biology and materials science. Cross-linked DNA fragments produced unmistakable current signatures in the nanopore experiment. Some cross-linked substrates gave irreversible current blocks of >10 min, while others produced long current blocks (10-100 s) before the double-stranded DNA cross-link translocated through the α-hemolysin channel in a voltage-driven manner. The duration of the current block for the different cross-linked substrates examined here may be dictated by the stability of the duplex region left in the vestibule of the nanopore following partial unzipping of the cross-linked DNA. Construction of calibration curves measuring the frequency of cross-link blocking events (1/τon) as a function of cross-link concentration enabled quantitative determination of the amounts of cross-linked DNA present in samples. The unique current signatures generated by cross-linked DNA in the α-HL nanopore may enable the detection and characterization of DNA cross-links that are important in toxicology, medicine, and materials science.

  3. Evaluation of the wear performance of a polycarbonate-urethane acetabular component in a hip joint simulator and comparison with UHMWPE and cross-linked UHMWPE.

    Science.gov (United States)

    St John, Kenneth; Gupta, Minakshi

    2012-07-01

    Acetabular hip joint components manufactured from gamma-sterilized ultra high molecular weight polyethylene (UHMWPE), gamma cross-linked UHMWPE, or polycarbonate-urethane (PCU) polymers were evaluated in a hip joint simulator, using cobalt alloy femoral components, for at least 5 million cycles. The volume of material losses due to wear was calculated for each type of sample, based upon mass loss measurements, every 500,000 cycles. The loss of material for the conventional UHMWPE was much higher than for the cross-linked UHMWPE, showing about a 70% reduction in wear due to cross-linking. The material loss for the PCU samples appears to have been at least 24% lower than for the cross-linked UHMWPE. Based upon these results, the PCU material seems to have potential for use as an alternative bearing material to UHMWPE for total hip replacement surgeries.

  4. Electronic DC transformer with high power density

    NARCIS (Netherlands)

    Pavlovský, M.

    2006-01-01

    This thesis is concerned with the possibilities of increasing the power density of high-power dc-dc converters with galvanic isolation. Three cornerstones for reaching high power densities are identified as: size reduction of passive components, reduction of losses particularly in active components

  5. Aluminum-induced dreierketten chain cross-links increase the mechanical properties of nanocrystalline calcium aluminosilicate hydrate

    Science.gov (United States)

    Geng, Guoqing; Myers, Rupert J.; Li, Jiaqi; Maboudian, Roya; Carraro, Carlo; Shapiro, David A.; Monteiro, Paulo J. M.

    2017-03-01

    The incorporation of Al and increased curing temperature promotes the crystallization and cross-linking of calcium (alumino)silicate hydrate (C-(A-)S-H), which is the primary binding phase in most contemporary concrete materials. However, the influence of Al-induced structural changes on the mechanical properties at atomistic scale is not well understood. Herein, synchrotron radiation-based high-pressure X-ray diffraction is used to quantify the influence of dreierketten chain cross-linking on the anisotropic mechanical behavior of C-(A-)S-H. We show that the ab-planar stiffness is independent of dreierketten chain defects, e.g. vacancies in bridging tetrahedra sites and Al for Si substitution. The c-axis of non-cross-linked C-(A-)S-H is more deformable due to the softer interlayer opening but stiffens with decreased spacing and/or increased zeolitic water and Ca2+ of the interlayer. Dreierketten chain cross-links act as ‘columns’ to resist compression, thus increasing the bulk modulus of C-(A-)S-H. We provide the first experimental evidence on the influence of the Al-induced atomistic configurational change on the mechanical properties of C-(A-)S-H. Our work advances the fundamental knowledge of C-(A-)S-H on the lowest level of its hierarchical structure, and thus can impact the way that innovative C-(A-)S-H-based cementitious materials are developed using a ‘bottom-up’ approach.

  6. Thermo-responsive shell cross-linked PMMA-b-P(NIPAAm-co-NAS) micelles for drug delivery.

    Science.gov (United States)

    Chang, Cong; Wei, Hua; Wu, De-Qun; Yang, Bin; Chen, Ni; Cheng, Si-Xue; Zhang, Xian-Zheng; Zhuo, Ren-Xi

    2011-11-28

    Thermo-responsive amphiphilic poly(methyl methacrylate)-b-poly(N-isopropylacrylamide-co-N-acryloxysuccinimide) (PMMA-b-P(NIPAAm-co-NAS)) block copolymer was synthesized by successive RAFT polymerizations. The uncross-linked micelles were facilely prepared by directly dissolving the block copolymer in an aqueous medium, and the shell cross-linked (SCL) micelles were further fabricated by the addition of ethylenediamine as a di-functional cross-linker into the micellar solution. Optical absorption measurements showed that the LCST of uncross-linked and cross-linked micelles was 31.0°C and 40.8°C, respectively. Transmission electron microscopy (TEM) showed that both uncross-linked and cross-linked micelles exhibited well-defined spherical shape in aqueous phase at room temperature, while the SCL micelles were able to retain the spherical shape with relatively smaller dimension even at 40°C due to the cross-linked structure. In vitro drug release study demonstrated a slower and more sustained drug release behavior from the SCL micelles at high temperature as compared with the release profile of uncross-linked micelles, indicating the great potential of SCL micelles developed herein as novel smart carriers for controlled drug release.

  7. Long-term durability of HT-PEM fuel cells based on thermally cross-linked polybenzimidazole

    Science.gov (United States)

    Søndergaard, Tonny; Cleemann, Lars Nilausen; Becker, Hans; Aili, David; Steenberg, Thomas; Hjuler, Hans Aage; Seerup, Larisa; Li, Qingfeng; Jensen, Jens Oluf

    2017-02-01

    Long-term durability of high temperature polymer electrolyte membrane fuel cells based on thermally cross-linked polybenzimidazole membranes was studied and compared with reference membranes based on linear polybenzimidazole. The test was conducted at 160 °C under constant load currents of 200 mA cm-2 for periods of 1000, 4400, and 13,000 h. Extensive beginning-of-life (BoL) and end-of-test (EoT) characterisation was carried out, and disturbance of the steady state operated cells was minimised by limiting in-line diagnostics to the low-invasive technique of electrochemical impedance spectroscopy (EIS). Up until the operating time of 9200 h, the cell equipped with the cross-linked membrane showed an average degradation rate of 0.5 μV h-1, compared to 2.6 μV h-1 for the reference membrane, though parallel tests for a shorter period of time showed deviations, likely due to malfunctioning contact between layers or cell components. For the full test period of 13,000 h, the average voltage decay rate was about 1.4 and 4.6 μV h-1 for cells equipped with cross-linked and linear polybenzimidazole membranes, respectively. EIS and post-test analysis revealed that the cross-linked membrane showed better stability in terms of area specific resistance due to improved acid retention characteristics.

  8. Fabrication of cross-linked hydrazone covalent organic frameworks by click chemistry and application to solid phase microextraction.

    Science.gov (United States)

    Wu, Mingxue; Chen, Gang; Ma, Jiutong; Liu, Ping; Jia, Qiong

    2016-12-01

    Covalent organic frameworks (COFs) are an emerging class of porous organic frameworks with diverse promising applications. Herein, we presented the first example of cross-linked hydrazone COFs (cross-linked COFs) coating via thiol-ene click chemistry for solid phase microextraction (SPME). Strong covalent bonds and interlayer of the prepared networks ensured the adsorption capacity and durability of the novel SPME fiber. π-π conjugated structure existed because of abundant phenyl rings and -C=N groups in the cross-lined COFs. A series of characterizations indicated that the cross-linked COFs possessed large surface areas, high porosities and stabilities as well as hydrophobicities. The fiber was applied to SPME of pesticide residues coupled with gas chromatography with an electron capture detector (GC-ECD). Under the optimum experimental conditions, enhancement factors in the range of 2190-10,998 were obtained, illustrating that the cross-linked COFs possessed remarkable preconcentration ability. The low detection limits of 0.0003-0.0023ngkg(-1) were achieved with relative standard deviations (RSDs) in the range of 3.4-7.6% (intra-batch) and 5.7-11.6% (inter-batch), respectively. Recovery values in the range of 78.2-107.0% were obtained when the SPME-GC method was applied to the analysis of pesticides in cucumber samples. Copyright © 2016 Elsevier B.V. All rights reserved.

  9. Stable Bioactive Enzyme-Containing Multilayer Films Based on Covalent Cross-Linking from Mussel-Inspired Adhesives.

    Science.gov (United States)

    Longo, Johan; Garnier, Tony; Mateescu, Mihaela; Ponzio, Florian; Schaaf, Pierre; Jierry, Loïc; Ball, Vincent

    2015-11-17

    The use of immobilized enzymes is mandatory for the easy separation of the enzyme, the unreacted substrates, and the obtained products to allow repeated enzymatic assays without cumbersome purification steps. The immobilization procedure is however critical to obtain a high fraction of active enzyme. In this article, we present an enzyme immobilization strategy based on a catechol functionalized alginate. We demonstrate that alkaline phosphatase (ALP) remains active in multilayered films made with alginate modified with catechol moieties (AlgCat) for long duration, that is, up to 7 weeks, provided the multilayered architecture is cross-linked with sodium periodate. This cross-linking reaction allows to create covalent bonds between the amino groups of ALP and the quinone group carried by the modified alginate. In the absence of cross-linking, the enzymatic activity is rapidly lost and this reduction is mainly due to enzyme desorption. We also show that NaIO4 cross-linked (AlgCat-Alp)n films can be freeze-dried and reused at least 3 weeks later without lost in enzymatic activity.

  10. Remarkable swelling capability of amino acid based cross-linked polymer networks in organic and aqueous medium.

    Science.gov (United States)

    Roy, Saswati Ghosh; Haldar, Ujjal; De, Priyadarsi

    2014-03-26

    This work reports design and synthesis of side chain amino acid based cross-linked polymeric gels, able to switch over from organogel to hydrogel by a simple deprotection reaction and showing superabsorbancy in water. Amino acid based methacrylate monomers, tert-butoxycarbonyl (Boc)-l/d-alanine methacryloyloxyethyl ester (Boc-l/d-Ala-HEMA), have been polymerized in the presence of a cross-linker via conventional free radical polymerization (FRP) and the reversible addition-fragmentation chain transfer (RAFT) technique for the synthesis of cross-linked polymer gels. The swelling behaviors of these organogels are investigated in organic solvents, and they behave as superabsorbent materials for organic solvents such as dichloromethane, acetone, tetrahydrofuran, etc. Swollen cross-linked polymer gels release the absorbed organic solvent rapidly. After Boc group deprotection from the pendant alanine moiety, the organogels transform to the hydrogels due to the formation of side chain ammonium (-NH3(+)) groups, and these hydrogels showed a significantly high swelling ratio (∼560 times than their dry volumes) in water. The morphology of organogels and hydrogels is studied by field emission scanning electron microscopy (FE-SEM). Amino acid based cross-linked gels could find applications as absorbents for oil spilled on water as well as superabsorbent hydrogels.

  11. Mapping the miRNA interactome by cross-linking ligation and sequencing of hybrids (CLASH).

    Science.gov (United States)

    Helwak, Aleksandra; Tollervey, David

    2014-03-01

    RNA-RNA interactions have critical roles in many cellular processes, but studying them is difficult and laborious. Here we describe an experimental procedure, termed cross-linking ligation and sequencing of hybrids (CLASH), which allows high-throughput identification of sites of RNA-RNA interaction. During CLASH, a tagged bait protein is UV-cross-linked in cell cultures to stabilize RNA interactions, and it is purified under denaturing conditions. RNAs associated with the bait protein are partially truncated, and the ends of RNA duplexes are ligated together. After linker addition, cDNA library preparation and high-throughput sequencing, the ligated duplexes give rise to chimeric cDNAs, which unambiguously identify RNA-RNA interaction sites independent of bioinformatic predictions. This protocol is optimized for studying miRNA targets bound by Argonaute (AGO) proteins, but it should be easily adapted for other RNA-binding proteins and classes of RNA. The protocol requires ∼5 d to complete, excluding the time required for high-throughput sequencing and bioinformatic analyses.

  12. Riboflavin-ultraviolet a corneal cross-linking for keratoconus

    Directory of Open Access Journals (Sweden)

    El-Raggal Tamer

    2009-01-01

    Full Text Available Purpose: To evaluate the safety, efficacy of riboflavin-ultraviolet A irradiation (UVA corneal cross-linking and present refractive changes induced by the treatment in cases of keratoconus. Materials and Methods: The study includes 15 eyes of 9 patients with keratoconus with an average keratometric (K reading less than 54 D and minimal corneal thickness greater than 420 microns. The corneal epithelium was removed manually within the central 8.5 mm diameter area and the cornea was soaked with riboflavin eye drops (0.1% in 20% dextran t-500 for 30 minutes followed by exposure to UVA radiation (365 nm, 3 mW/cm 2 for 30 minutes. During the follow-up period, uncorrected visual acuity (UCVA, best spectacle-corrected visual acuity (BSCVA, manifest refraction, slit lamp examination and topographic changes were recorded at the first week, first month, 3 and 6 months. Results: There was statistically significant improvement of UCVA from a preoperative mean of 0.11 ± 0.07 (range 0.05-0.3 to a postoperative mean of 0.15 ± 0.06 (range 0.1-0.3 (P < 0.05. None of the eyes lost lines of preoperative UCVA but 1 eye lost 1 line of preoperative BSCVA. The preoperative mean K of 49.97 ± 2.81 D (range 47.20-51.75 changed to 48.34 ± 2.64 D (range 45.75-50.40. This decrease in K readings was statistically significant (P < 0.05. All eyes developed minimal faint stromal haze that cleared in 14 eyes within 1 month. In only 1 eye, this resulted in a very faint corneal scar. Other sight threatening complications were not encountered in this series. Progression of the original disease was not seen in any of the treated eyes within 6 months of follow-up. Conclusion: Riboflavin-UVA corneal cross-linking is a safe and promising method for keratoconus. Larger studies with longer follow up are recommended.

  13. High regression rate, high density hybrid fuels Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR program will investigate high energy density novel nanofuels combined with high density binders for use with an N2O oxidizer. Terves has developed...

  14. High energy density lithium batteries

    CERN Document Server

    Aifantis, Katerina E; Kumar, R Vasant

    2010-01-01

    Cell phones, portable computers and other electronic devices crucially depend on reliable, compact yet powerful batteries. Therefore, intensive research is devoted to improving performance and reducing failure rates. Rechargeable lithium-ion batteries promise significant advancement and high application potential for hybrid vehicles, biomedical devices, and everyday appliances. This monograph provides special focus on the methods and approaches for enhancing the performance of next-generation batteries through the use of nanotechnology. Deeper understanding of the mechanisms and strategies is

  15. Wear of cross-linked polyethylene against itself: a material suitable for surface replacement of the finger joint.

    Science.gov (United States)

    Sibly, T F; Unsworth, A

    1991-05-01

    Cross-linking of polyethylene (XLPE) has dramatically improved its properties in industrial applications, and it may also have some application in the field of human joint replacement. Additionally it has the advantage of permitting a lower molecular weight base material to be used, so that components may be injection moulded rather than machined. This study therefore investigates the wear resistance of medical grade cross-linked polyethylene (XLPE), cross-linked by a silane-grafting process, with a molecular weight between cross links of 5430 g mol(-1). This first report investigates the wear resistance of XLPE against itself, because for certain joints, such as the metacarpo-phalangeal joint, the material may have a high enough wear resistance to allow both bearing surfaces to be made from it. Tests were carried out both on a reciprocating pin and plate machine with pins loaded at 10 and 40 N and also on a new finger joint simulator, which simulates the loads applied to and the movements of, the metacarpo-phalangeal joint. An average wear rate of 1.8 x 10(-6) mm3 N-1 m-1 was found (range 0.9-2.75 x 10(-6) mm3 N-1 m-1). This is about six times greater than the wear rate of non-cross-linked ultra high molecular weight polyethylene (UHMWPE) against stainless steel, but for applications with low loading, such as the metacarpo-phalangeal joint, this material is shown to have adequate wear resistance. The coefficient of friction was 0.1, which is similar to that of UHMWPE on stainless steel.

  16. Mono-dispersed cross-linked polystyrene micro-spheres prepared by seed swelling polymerization method

    Institute of Scientific and Technical Information of China (English)

    Dongsha WANG; Yanjun LIU

    2008-01-01

    A two-step swelling procedure was adopted to synthesize mono-dispersed and highly cross-linked poly (St-divinylbenzene) particles with PSt micro-spheres (1.80 μmin diameter). The PSt micro-spheres were prepared by a dispersion polymerization method and used as seeds. The effects of monomer concentration, ratio of ethanol to water, swelling reagents, crosslinking reagents, swelling temper-ature and agitation speed on particle size were investigated in detail. The morphologies and size distributions of these micro-spheres were examined by SEM and particle size analysis (PSA). The Tg of the micro-spheres was measured by DSC. The results indicate that the particles (6.20 μm in diameter) exhibit excellent mono dispersed property and high crosslinking degree when the concentration of the swelling reagent was 25%, the concentration of the cross-linking reagents was 23%, the swelling temperature was 30℃ and the stirring speed was 150 r/min.

  17. Continuous Sensing Photonic Lab-on-a-Chip Platform Based on Cross-Linked Enzyme Crystals.

    Science.gov (United States)

    Conejero-Muriel, Mayte; Rodríguez-Ruiz, Isaac; Verdugo-Escamilla, Cristóbal; Llobera, Andreu; Gavira, José A

    2016-12-06

    Microfluidics or lab-on-a-chip technology offer clear advantages over conventional systems such as a dramatic reduction of reagent consumption or a shorter analysis time, which are translated into cost-effective systems. In this work, we present a photonic enzymatic lab-on-a-chip reactor based on cross-linked enzyme crystals (CLECs), able to work in continuous flow, as a highly sensitive, robust, reusable, and stable platform for continuous sensing with superior performance as compared to the state of the art. The microreactor is designed to facilitate the in situ crystallization and crystal cross-linking generating enzymatically active material that can be stored for months/years. Thus, and by means of monolithically integrated micro-optics elements, continuous enzymatic reactions can be spectrophotometrically monitored. Lipase, an enzyme with industrial significance for catalyzed transesterification, hydrolysis, and esterification reactions, is used to demonstrate the potential of the microplatforms as both a continuous biosensor and a microreactor for the synthesis of high value compounds.

  18. [Healing of osseous defects by guided bone regeneration using ribose cross linked collagen membranes].

    Science.gov (United States)

    Tal, H

    2004-07-01

    The ultimate goal of periodontal therapy has long been the complete regeneration of the periodontal attachment apparatus. Guided Tissue Regeneration (GTR) and Guided Bone Regeneration (GBR) are two regenerative procedures which converted this goal from a dream to reality. In search of a biocompatible resorbable tissue barrier, collagen, being a natural protein and a weak antigen, has attracted much interest and became the focus of much intention during the 80's and the 90's. The understanding that cross linking of collagen with aldehyde sugars, especially ribose, produces collagen which is highly resistant to resorption in vivo led to the development of a "natural" Crossed-Linked Collagen Barrier (CB-SX). Animal and Human studies have shown that the newly developed membrane is biocompatible, remains intact in the tissues 6 months and more, and results in impressive guided tissue/bone regeneration. Spontaneous early exposure of the membrane is common but the healing potential of the resulted tissue dehiscence is favorable with no tendency for bacterial infection. The commercial version of the CB-SX is especially suitable for GBR procedures; it is highly recommended that the gingival flaps involved will properly be released, will lack tension, and be thoroughly sutured.

  19. Nafion-assisted cross-linking of sulfonated poly(arylene ether ketone) bearing carboxylic acid groups and their composite membranes for fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Haidan; Zhao, Chengji; Na, Hui [Alan G. MacDiarmid Institute, College of Chemistry, Jilin University, Qianjin street 2699, Changchun 130012, Jilin (China)

    2010-06-01

    In this study, a new type of cross-linked composite membrane is prepared and considered for its potential applications in direct methanol fuel cell. Nafion and sulfonated poly(arylene ether ketone) bearing carboxylic acid groups (SPAEK-C) are blended and subsequently cross-linked by a Friedel-Craft reaction using the carboxylic acid groups in the SPAEK-C to achieve lower methanol permeability. The perfluoroalkyl sulfonic acid groups of Nafion act as a benign solid catalyst, which assist the cross-linking of SPAEK-C. The physical and chemical characterizations of the cross-linked composite membranes are performed by varying the contents of SPAEK-C. The c-Nafion-15% membrane exhibits appropriate water uptake (10.49-25.22%), low methanol permeability (2.57 x 10{sup -7} cm{sup 2} s{sup -1}), and high proton conductivity (0.179 S cm{sup -1} at 80 C). DSC and FTIR analyze suggest the cross-linking reaction. These results show that the self-cross-linking of SPAEK-C in the Nafion membrane can effectively reduce methanol permeability while maintaining high proton conductivity. (author)

  20. Energy harvesting from vibration with cross-linked polypropylene piezoelectrets

    Directory of Open Access Journals (Sweden)

    Xiaoqing Zhang

    2015-07-01

    Full Text Available Piezoelectret films are prepared by modification of the microstructure of polypropylene foam sheets cross-linked by electronic irradiation (IXPP, followed by proper corona charging. Young’s modulus, relative permittivity, and electromechanical coupling coefficient of the fabricated films, determined by dielectric resonance spectra, are about 0.7 MPa, 1.6, and 0.08, respectively. Dynamic piezoelectric d33 coefficients up to 650 pC/N at 200 Hz are achieved. The figure of merit (FOM, d33 ⋅ g33 for a more typical d33 value of 400 pC/N is about 11.2 GPa−1. Vibration-based energy harvesting with one-layer and two-layer stacks of these films is investigated at various frequencies and load resistances. At an optimum load resistance of 9 MΩ and a resonance frequency of 800 Hz, a maximum output power of 120 μW, referred to the acceleration g due to gravity, is obtained for an energy harvester consisting of a one-layer IXPP film with an area of 3.14 cm2 and a seismic mass of 33.7 g. The output power can be further improved by using two-layer stacks of IXPP films in electric series. IXPP energy harvesters could be used to energize low-power electronic devices, such as wireless sensors and LED lights.

  1. Cross-linking da cornea: protocolo padrão

    Directory of Open Access Journals (Sweden)

    Marcony R. Santhiago

    Full Text Available RESUMO O objetivo desta revisão é de determinar as indicações e eficácia da cirurgia que promove novas ligações covalentes entre as fibras de colágeno da córnea, conhecida como Cross-Linking (CXL, assim como esclarecer seus objetivos. O ceratocone é uma doença ectasica da córnea, bilateral, assimétrica, que, principalmente, cursa com encurvamento e afinamentos progressivo, e se inicia em geral na segunda década de vida. O uso primário do CXL tem sido na interrupção da progressão do Ceratocone. Apesar do conhecido encurvamento no estroma da córnea ocorrer nesses pacientes, a fisiopatologia por trás do ceratocone ainda é desconhecida e parece ser multifatorial. Pela evidencia literária disponível até o momento, o CXL da córnea esta, portanto indicado nos pacientes com doença em progressão. Concluímos que existe evidencia suficiente para afirmar que o CXL da córnea é eficaz na estabilização da doença ectásica da cornea.

  2. Energy harvesting from vibration with cross-linked polypropylene piezoelectrets

    Science.gov (United States)

    Zhang, Xiaoqing; Wu, Liming; Sessler, Gerhard M.

    2015-07-01

    Piezoelectret films are prepared by modification of the microstructure of polypropylene foam sheets cross-linked by electronic irradiation (IXPP), followed by proper corona charging. Young's modulus, relative permittivity, and electromechanical coupling coefficient of the fabricated films, determined by dielectric resonance spectra, are about 0.7 MPa, 1.6, and 0.08, respectively. Dynamic piezoelectric d33 coefficients up to 650 pC/N at 200 Hz are achieved. The figure of merit (FOM, d33 ṡ g33) for a more typical d33 value of 400 pC/N is about 11.2 GPa-1. Vibration-based energy harvesting with one-layer and two-layer stacks of these films is investigated at various frequencies and load resistances. At an optimum load resistance of 9 MΩ and a resonance frequency of 800 Hz, a maximum output power of 120 μW, referred to the acceleration g due to gravity, is obtained for an energy harvester consisting of a one-layer IXPP film with an area of 3.14 cm2 and a seismic mass of 33.7 g. The output power can be further improved by using two-layer stacks of IXPP films in electric series. IXPP energy harvesters could be used to energize low-power electronic devices, such as wireless sensors and LED lights.

  3. Energy harvesting from vibration with cross-linked polypropylene piezoelectrets

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Xiaoqing [Shanghai Key Laboratory of Special Artificial Microstructure Materials and Technology & School of Physics Science and Engineering, Tongji University, Shanghai 200092 (China); Institute for Telecommunications Technology, Merckstrasse 25, 64283 Darmstadt (Germany); Wu, Liming [Shanghai Key Laboratory of Special Artificial Microstructure Materials and Technology & School of Physics Science and Engineering, Tongji University, Shanghai 200092 (China); Sessler, Gerhard M., E-mail: g.sessler@nt.tu-darmstadt.de [Institute for Telecommunications Technology, Merckstrasse 25, 64283 Darmstadt (Germany)

    2015-07-15

    Piezoelectret films are prepared by modification of the microstructure of polypropylene foam sheets cross-linked by electronic irradiation (IXPP), followed by proper corona charging. Young’s modulus, relative permittivity, and electromechanical coupling coefficient of the fabricated films, determined by dielectric resonance spectra, are about 0.7 MPa, 1.6, and 0.08, respectively. Dynamic piezoelectric d{sub 33} coefficients up to 650 pC/N at 200 Hz are achieved. The figure of merit (FOM, d{sub 33} ⋅ g{sub 33}) for a more typical d{sub 33} value of 400 pC/N is about 11.2 GPa{sup −1}. Vibration-based energy harvesting with one-layer and two-layer stacks of these films is investigated at various frequencies and load resistances. At an optimum load resistance of 9 MΩ and a resonance frequency of 800 Hz, a maximum output power of 120 μW, referred to the acceleration g due to gravity, is obtained for an energy harvester consisting of a one-layer IXPP film with an area of 3.14 cm{sup 2} and a seismic mass of 33.7 g. The output power can be further improved by using two-layer stacks of IXPP films in electric series. IXPP energy harvesters could be used to energize low-power electronic devices, such as wireless sensors and LED lights.

  4. Subclinical inflammatory response after accelerated corneal cross-linking

    Institute of Scientific and Technical Information of China (English)

    Hassan Hashemi; Nahid Ashraf; Ebrahim Jafarzadehpur; Alireza Hedayatfar; Soheila Asgari

    2016-01-01

    Background: To evaluate the inlfammatory response after accelerated collagen cross-linking (CXL) in eyes with keratoconus. Methods: Consecutive eyes with keratoconus undergoing CXL surgery were included in this non-randomized interventional study. Aqueous lfare was measured pre- and post-operatively with a laser lfare photometer at 1 week, 1, 3 and 6 months after CXL. Results: Sixty eyes of 60 patients were entered into the study. Before CXL, the mean lfare value was 4.5 photons per millisecond (ph/ms). The lfare values observed at week 1 (7.1 ph/ms; P=0.008), month 1 (6.5 ph/ms; P=0.04), month 3 (6.7 ph/ms; P=0.004) and month 6 (6.7 ph/ms; P=0.004) were signiifcantly higher compared to baseline. Flare values were not signiifcantly different from week 1 up to 6 months after CXL (P=0.930). No statistically significant correlation was detected between the amount of inlfammation and keratometric indices. Conclusions: Accelerated CXL in patients with keratoconus may cause a subclinical inflammatory response which is evident as slight but rather long-lasting rise of aqueous lfare.

  5. Pyridinium cross-links in heritable disorders of collagen

    Energy Technology Data Exchange (ETDEWEB)

    Pasquali, M.; Still, M.J.; Dembure, P.P. [Emory Univ., Atlanta, GA (United States)] [and others

    1995-12-01

    Ehlers-Danlos syndrome (EDS) is a heterogeneous group of inherited disorders of collagen that is characterized by skin fragility, skin hyperextensibility, and joint hypermobility. EDS type VI is caused by impaired collagen lysyl hydroxylase (procollagen-lysine, 2-oxoglutarate 5-dioxygenase; E.C.1.14.11.4), the ascorbate-dependent enzyme that hydroxylates lysyl residues on collagen neopeptides. Different alterations in the gene for collagen lysyl hydroxylase have been reported in families with EDS type VI. In EDS type VI, impairment of collagen lysyl hydroxylase results in a low hydroxylysine content in mature collagen. Hydroxylysine is a precursor of the stable, covalent, intermolecular cross-links of collagen, pyridinoline (Pyr), and deoxypyridinoline (Dpyr). Elsewhere we reported in preliminary form that patients with EDS type VI had a distinctive alteration in the urinary excretion of Pyr and Dpyr. In the present study, we confirm that the increased Dpyr/Pyr ratio is specific for EDS type VI and is not observed in other inherited or acquired collagen disorders. In addition, we find that skin from patients with EDS type VI has reduced Pyr and increased Dpyr, which could account for the organ pathology. 19 refs., 1 tab.

  6. Characteristics of recycled and electron beam irradiated high density polyethylene samples

    Energy Technology Data Exchange (ETDEWEB)

    Cardoso, Jessica R.; Gabriel, Leandro; Geraldo, Aurea B.C.; Moura, Eduardo, E-mail: jrcardoso@ipen.br, E-mail: lgabriell@gmail.com, E-mail: ageraldo@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2015-07-01

    Polymers modification by irradiation is a well-known process that allows degradation and cross-linking in concurrent events; this last is expected when an increase of mechanical properties is required. Actually, the interest of recycling and reuse of polymeric material is linked to the increase of plastics ending up in waste streams. Therefore, these both irradiation and recycling process may be conducted to allow a new use to this material that would be discarded by an improvement of its mechanical properties. In this work, the High Density Polyethylene (HDPE) matrix has been recycled five times from original substrate. The electron beam irradiation process was applied from 50 kGy to 200 kGy in both original and recycled samples; in this way, mechanical properties and thermal characteristics were evaluated. The results of applied process and material characterization are discussed. (author)

  7. Different Topographic Response Between Mild to Moderate and Advanced Keratoconus After Accelerated Collagen Cross-linking.

    Science.gov (United States)

    Chan, Tommy C Y; Chow, Vanissa W S; Jhanji, Vishal; Wong, Victoria W Y

    2015-08-01

    To evaluate the clinical and topographic effects after accelerated corneal collagen cross-linking (CXL) in keratoconus. This was a prospective interventional study in 25 eyes of 24 Asian patients with keratoconus, where 10 eyes in group 1 had mild to moderate keratoconus with the steepest keratometry reading (Kmax) keratoconus with Kmax ≥ 58.0 D. The patients underwent accelerated CXL with 18 W/cm UV-A light for 5 minutes. Clinical and topographic parameters were obtained before and 1 year after treatment. Overall, spectacle-corrected distance visual acuity, refraction, average keratometry readings, Kmax, anterior elevation at the apex, and corneal endothelial cell density remained stable (P keratoconus but not as effective in the less progressed counterparts.

  8. Nonlinear behavior of ionically and covalently cross-linked alginate hydrogels

    Science.gov (United States)

    Hashemnejad, Seyedmeysam; Zabet, Mahla; Kundu, Santanu

    2015-03-01

    Gels deform differently under applied load and the deformation behavior is related to their network structures and environmental conditions, specifically, strength and density of crosslinking, polymer concentration, applied load, and temperature. Here, we investigate the mechanical behavior of both ionically and covalent cross-linked alginate hydrogel using large amplitude oscillatory shear (LAOS) and cavitation experiments. Ionically-bonded alginate gels were obtained by using divalent calcium. Alginate volume fraction and alginate to calcium ratio were varied to obtain gels with different mechanical properties. Chemical gels were synthesized using adipic acid dihdrazide (AAD) as a cross-linker. The non-linear rheological parameters are estimated from the stress responses to elucidate the strain softening behavior of these gels. Fracture initiation and propagation mechanism during shear rheology and cavitation experiments will be presented. Our results provide a better understanding on the deformation mechanism of alginate gel under large-deformation.

  9. Dehydration Mechanism of Secondary Cross-linked Gels%二次交联凝胶脱水机理研究

    Institute of Scientific and Technical Information of China (English)

    罗宪波; 武海燕; 周晶; 蒲万芬; 赵金洲

    2005-01-01

    In this paper, microscopic characteristics of preformed gels (PGs) and secondary cross-linked gels (SCG) with the same concentration were analyzed by atomic force microscopy (AFM). Experimental results indicate that the microstructure of secondary cross-linked gels is a thick 3-D network, in which micro-holes and irregular macro-holes are embedded. The maximum width of the irregular macro-holes is 200 nm. In the SCG, two different chemical bonds were formed, which leads to the structural inhomogeneity and the asymmetry of the crosslinking density. The structural inhomogeneity of SCG results in the formation of irregular macro-holes. The excessive cross-linking density is the primary reason for dehydration of SCG and the presence of irregular macro-holes in SCG can facilitate dehydration.

  10. Cross-links between ribosomal proteins of 30S subunits in 70S tight couples and in 30S subunits.

    Science.gov (United States)

    Lambert, J M; Boileau, G; Cover, J A; Traut, R R

    1983-08-01

    Ribosome 70S tight couples and 30S subunits derived from them were modified with 2-iminothiolane under conditions where about two sulfhydryl groups per protein were added to the ribosomal particles. The 70S and 30S particles were not treated with elevated concentrations of NH4Cl, in contrast to those used in earlier studies. The modified particles were oxidized to promote disulfide bond formation. Proteins were extracted from the cross-linked particles by using conditions to preclude disulfide interchange. Disulfide-linked protein complexes were fractionated on the basis of charge by electrophoresis in polyacrylamide/urea gels at pH 5.5. The proteins from sequential slices of the urea gels were analyzed by two-dimensional diagonal polyacrylamide/sodium dodecyl sulfate gel electrophoresis. Final identification of proteins in cross-linked complexes was made by radioiodination of the proteins, followed by two-dimensional polyacrylamide/urea gel electrophoresis. Attention was focused on cross-links between 30S proteins. We report the identification of 27 cross-linked dimers and 2 trimers of 30S proteins, all but one of which were found in both 70S ribosomes and free 30S subunits in similar yield. Seven of the cross-links, S3-S13, S13-S21, S14-S19, S7-S12, S9-S13, S11-S21, and S6-S18-S21, have not been reported previously when 2-iminothiolane was used. Cross-links S3-S13, S13-S21, S7-S12, S11-S21, and S6-S18-S21 are reported for the first time. The identification of the seven new cross-links is illustrated and discussed in detail. Ten of the dimers reported in the earlier studies of Sommer & Traut (1976) [Sommer, A., & Traut, R. R. (1976) J. Mol. Biol. 106, 995-1015], using 30S subunits treated with high salt concentrations, were not found in the experiments reported here.

  11. Analysis of protein-nucleic acid interactions by photochemical cross-linking and mass spectrometry

    DEFF Research Database (Denmark)

    Steen, Hanno; Jensen, Ole Nørregaard

    2002-01-01

    Photochemical cross-linking is a commonly used method for studying the molecular details of protein-nucleic acid interactions. Photochemical cross-linking aids in defining nucleic acid binding sites of proteins via subsequent identification of cross-linked protein domains and amino acid residues....... Mass spectrometry (MS) has emerged as a sensitive and efficient analytical technique for determination of such cross-linking sites in proteins. The present review of the field describes a number of MS-based approaches for the characterization of cross-linked protein-nucleic acid complexes...... and for sequencing of peptide-nucleic acid heteroconjugates. The combination of photochemical cross-linking and MS provides a fast screening method to gain insights into the overall structure and formation of protein-oligonucleotide complexes. Because the analytical methods are continuously refined and protein...

  12. Characterization of the deoxyguanosine-lysine cross-link of methylglyoxal.

    Science.gov (United States)

    Petrova, Katya V; Millsap, Amy D; Stec, Donald F; Rizzo, Carmelo J

    2014-06-16

    Methylglyoxal is a mutagenic bis-electrophile that is produced endogenously from carbohydrate precursors. Methylglyoxal has been reported to induce DNA-protein cross-links (DPCs) in vitro and in cultured cells. Previous work suggests that these cross-links are formed between guanine and either lysine or cysteine side chains. However, the chemical nature of the methylglyoxal induced DPC have not been determined. We have examined the reaction of methylglyoxal, deoxyguanosine (dGuo), and Nα-acetyllysine (AcLys) and determined the structure of the cross-link to be the N2-ethyl-1-carboxamide with the lysine side chain amino group (1). The cross-link was identified by mass spectrometry and the structure confirmed by comparison to a synthetic sample. Further, the cross-link between methylglyoxal, dGuo, and a peptide (AcAVAGKAGAR) was also characterized. The mechanism of cross-link formation is likely to involve an Amadori rearrangement.

  13. Fabrication of patterned calcium cross-linked alginate hydrogel films and coatings through reductive cation exchange.

    Science.gov (United States)

    Bruchet, Marion; Melman, Artem

    2015-10-20

    Calcium cross-linked alginate hydrogels are widely used in targeted drug delivery, tissue engineering, wound treatment, and other biomedical applications. We developed a method for preparing homogeneous alginate hydrogels cross-linked with Ca(2+) cations using reductive cation exchange in homogeneous iron(III) cross-linked alginate hydrogels. Treatment of iron(III) cross-linked alginate hydrogels with calcium salts and sodium ascorbate results in reduction of iron(III) cations to iron(II) that are instantaneously replaced with Ca(2+) cations, producing homogeneous ionically cross-linking hydrogels. Alternatively, the cation exchange can be performed by photochemical reduction in the presence of calcium chloride using a sacrificial photoreductant. This approach allows fabrication of patterned calcium alginate hydrogels through photochemical patterning of iron(III) cross-linked alginate hydrogel followed by the photochemical reductive exchange of iron cations to calcium.

  14. An Open Data Format for Visualization and Analysis of Cross-Linked Mass Spectrometry Results.

    Science.gov (United States)

    Hoopmann, Michael R; Mendoza, Luis; Deutsch, Eric W; Shteynberg, David; Moritz, Robert L

    2016-11-01

    Protein-protein interactions are an important element in the understanding of protein function, and chemical cross-linking shotgun mass spectrometry is rapidly becoming a routine approach to identify these specific interfaces and topographical interactions. Protein cross-link data analysis is aided by dozens of algorithm choices, but hindered by a lack of a common format for representing results. Consequently, interoperability between algorithms and pipelines utilizing chemical cross-linking remains a challenge. pepXML is an open, widely-used format for representing spectral search algorithm results that has facilitated information exchange and pipeline development for typical shotgun mass spectrometry analyses. We describe an extension of this format to incorporate cross-linking spectral search results. We demonstrate application of the extension by representing results of multiple cross-linking search algorithms. In addition, we demonstrate adapting existing pepXML-supporting software pipelines to analyze protein cross-linking results formatted in pepXML. Graphical Abstract ᅟ.

  15. Blind testing cross-linking/mass spectrometry under the auspices of the 11th critical assessment of methods of protein structure prediction (CASP11 [version 1; referees: 1 approved, 2 approved with reservations

    Directory of Open Access Journals (Sweden)

    Adam Belsom

    2016-12-01

    Full Text Available Determining the structure of a protein by any method requires various contributions from experimental and computational sides. In a recent study, high-density cross-linking/mass spectrometry (HD-CLMS data in combination with ab initio structure prediction determined the structure of human serum albumin (HSA domains, with an RMSD to X-ray structure of up to 2.5 Å, or 3.4 Å in the context of blood serum. This paper reports the blind test on the readiness of this technology through the help of Critical Assessment of protein Structure Prediction (CASP. We identified between 201-381 unique residue pairs at an estimated 5% FDR (at link level albeit with missing site assignment precision evaluation, for four target proteins. HD-CLMS proved reliable once crystal structures were released. However, improvements in structure prediction using cross-link data were slight. We identified two reasons for this. Spread of cross-links along the protein sequence and the tightness of the spatial constraints must be improved. However, for the selected targets even ideal contact data derived from crystal structures did not allow modellers to arrive at the observed structure. Consequently, the progress of HD-CLMS in conjunction with computational modeling methods as a structure determination method, depends on advances on both arms of this hybrid approach.

  16. Tailoring the properties of cholecyst-derived extracellular matrix using carbodiimide cross-linking.

    LENUS (Irish Health Repository)

    Burugapalli, Krishna

    2009-01-01

    Modulation of properties of extracellular matrix (ECM) based scaffolds is key for their application in the clinical setting. In the present study, cross-linking was used as a tool for tailoring the properties of cholecyst-derived extracellular matrix (CEM). CEM was cross-linked with varying cross-linking concentrations of N,N-(3-dimethyl aminopropyl)-N\\'-ethyl carbodiimide (EDC) in the presence of N-hydroxysuccinimide (NHS). Shrink temperature measurements and ATR-FT-IR spectra were used to determine the degree of cross-linking. The effect of cross-linking on degradation was tested using the collagenase assay. Uniaxial tensile properties and the ability to support fibroblasts were also evaluated as a function of cross-linking. Shrink temperature increased from 59 degrees C for non-cross-linked CEM to 78 degrees C for the highest EDC cross-linking concentration, while IR peak area ratios for the free -NH(2) group at 3290 cm(-1) to that of the amide I band at 1635 cm(-1) decreased with increasing EDC cross-linking concentration. Collagenase assay demonstrated that degradation rates for CEM can be tailored. EDC concentrations 0 to 0.0033 mmol\\/mg CEM were the cross-linking concentration range in which CEM showed varied susceptibility to collagenase degradation. Furthermore, cross-linking concentrations up to 0.1 mmol EDC\\/mg CEM did not have statistically significant effect on the uniaxial tensile strength, as well as morphology, viability and proliferation of fibroblasts on CEM. In conclusion, the degradation rates of CEM can be tailored using EDC-cross-linking, while maintaining the mechanical properties and the ability of CEM to support cells.

  17. In vitro cross-linking of elastin peptides and molecular characterization of the resultant biomaterials.

    Science.gov (United States)

    Heinz, Andrea; Ruttkies, Christoph K H; Jahreis, Günther; Schräder, Christoph U; Wichapong, Kanin; Sippl, Wolfgang; Keeley, Fred W; Neubert, Reinhard H H; Schmelzer, Christian E H

    2013-04-01

    Elastin is a vital protein and the major component of elastic fibers which provides resilience to many vertebrate tissues. Elastin's structure and function are influenced by extensive cross-linking, however, the cross-linking pattern is still unknown. Small peptides containing reactive allysine residues based on sequences of cross-linking domains of human elastin were incubated in vitro to form cross-links characteristic of mature elastin. The resultant insoluble polymeric biomaterials were studied by scanning electron microscopy. Both, the supernatants of the samples and the insoluble polymers, after digestion with pancreatic elastase or trypsin, were furthermore comprehensively characterized on the molecular level using MALDI-TOF/TOF mass spectrometry. MS(2) data was used to develop the software PolyLinX, which is able to sequence not only linear and bifunctionally cross-linked peptides, but for the first time also tri- and tetrafunctionally cross-linked species. Thus, it was possible to identify intra- and intermolecular cross-links including allysine aldols, dehydrolysinonorleucines and dehydromerodesmosines. The formation of the tetrafunctional cross-link desmosine or isodesmosine was unexpected, however, could be confirmed by tandem mass spectrometry and molecular dynamics simulations. The study demonstrated that it is possible to produce biopolymers containing polyfunctional cross-links characteristic of mature elastin from small elastin peptides. MALDI-TOF/TOF mass spectrometry and the newly developed software PolyLinX proved suitable for sequencing of native cross-links in proteolytic digests of elastin-like biomaterials. The study provides important insight into the formation of native elastin cross-links and represents a considerable step towards the characterization of the complex cross-linking pattern of mature elastin. Copyright © 2013 Elsevier B.V. All rights reserved.

  18. A covalently cross-linked gel derived from the epidermis of the pilot whale Globicephala melas.

    Science.gov (United States)

    Baum, C; Fleischer, L-G; Roessner, D; Meyer, W; Siebers, D

    2002-01-01

    The rheological properties of the stratum corneum of the pilot whale (Globicephala melas) were investigated with emphasis on their significance to the self-cleaning abilities of the skin surface smoothed by a jelly material enriched with various hydrolytic enzymes. The gel formation of the collected fluid was monitored by applying periodic-harmonic oscillating loads using a stress-controlled rheometer. In the mechanical spectrum of the gel, the plateau region of the storage modulus G' (120 Pa) were independent of frequency (omega = 43.98 to 0.13 rad x s(-1), tau = 15 Pa, T = 20 degrees C), indicating high elastic performance of a covalently cross-linked viscoelastic solid. In addition, multi-angle laser light scattering experiments (MALLS) were performed to analyse the potential time-dependent changes in the weight-average molar mass of the samples. The observed increase showed that the gel formation is based on the assembly of covalently cross-linked aggregates. The viscoelastic properties and the shear resistance of the gel assure that the enzyme-containing jelly material smoothing the skin surface is not removed from the stratum corneum by shear regimes during dolphin jumping. The even skin surface is considered to be most important for the self-cleaning abilities of the dolphin skin against biofouling.

  19. Internal acetylene unit as a cross-link site for polyimides

    Energy Technology Data Exchange (ETDEWEB)

    Takeichi, T.; Tanikawa, M. [Toyohashi Univ. of Technology (Japan)

    1995-12-01

    We have been studying on the cross-linking behavior of internal acetylenes linked meta-meta to aromatic connecting units which were introduced into the polyimide backbone utilizing 3,3`-diaminodiphenylacetylene (m-intA). In this study, we studied on the cross-linking behavior of internal acetylenes linked para-para to aromatic connecting units. The internal acetylene units were introduced into the polyimide backbone by the reaction of 4,4`-diaminodiphenylacetylene (p-intA) with such acid anhydrides as biphenyltetracarboxylic dianhydride (BPDA), pyromellitic dianhydride (PMDA), and 2,2-bis(3,4-dicarboxyphenyl)hexafluoropropane dianhydride (6FDA). The polyimides showed exotherm on DSC: The onset of the exotherm of p-intA appeared at around 330-390{degrees}C, which is 10-50{degrees}C higher than that of m-intA. The exotherm disappeared after thermal treatment at 400{degrees}C, suggesting the progress of crosslinking between acetylene units. The polyimides cured at 350{degrees}C or 400{degrees}C showed increased Tg and improved physical properties at high temperatures as confirmed by viscoelastic analyses. It was also made clear that polyimides containing p-intA showed higher modulus compared with polyimides containing m-intA, especially when coupled with BPDA and PMDA.

  20. Entrapment of cross-linked cellulase colloids in alginate beads for hydrolysis of cellulose.

    Science.gov (United States)

    Nguyen, Le Truc; Lau, Yun Song; Yang, Kun-Lin

    2016-09-01

    Entrapment of enzymes in calcium alginate beads is a popular enzyme immobilization method. However, leaching of immobilized enzymes from the alginate beads is a common problem because enzyme molecules are much smaller than the pore size of alginate beads (∼200nm). To address this issue, we employ a millifluidic reactor to prepare cross-linked cellulase aggregate (XCA) colloids with a uniform size (∼300nm). Subsequently, these colloids are immobilized in calcium alginate beads as biocatalysts to hydrolyze cellulose substrates. By using fluorescent microscopy, we conclude that the immobilized XCA colloids distribute uniformly inside the beads and do not leach out from the beads after long-term incubation. Meanwhile, the pore size of the alginate beads is big enough for the cellulose substrates and fibers to diffuse into the beads for hydrolysis. For example, palm oil fiber and microcrystalline cellulose can be hydrolyzed within 48h and release reducing sugar concentrations up to 2.48±0.08g/l and 4.99±0.09g/l, respectively. Moreover, after 10 cycles of hydrolysis, 96.4% of the XCA colloids remain inside the alginate beads and retain 67% of the original activity. In contrast, free cellulase immobilized in the alginate beads loses its activity completely after 10 cycles. The strategy can also be used to prepare other types of cross-linked enzyme aggregates with high uniformity. Copyright © 2016 Elsevier B.V. All rights reserved.

  1. Removal of anionic azo dyes from aqueous solution by functional ionic liquid cross-linked polymer

    Energy Technology Data Exchange (ETDEWEB)

    Gao, Hejun [Key Laboratory of Colloid and Interface Chemistry, Shandong University, Ministry of Education, Jinan 250100 (China); Chemical Synthesis and Pollution Control Key Laboratory of Sichuan Province, China West Normal University, Nanchong 637000 (China); Kan, Taotao [CNOOC Energy Technology and Services-oilfield Technology Services Co., Tanggu, Tianjin 300452 (China); Zhao, Siyuan; Qian, Yixia; Cheng, Xiyuan; Wu, Wenli [School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Wang, Xiaodong [Shandong Provincial Analysis and Test Center, Jinan 250100 (China); Zheng, Liqiang, E-mail: lqzheng@sdu.edu.cn [Key Laboratory of Colloid and Interface Chemistry, Shandong University, Ministry of Education, Jinan 250100 (China)

    2013-10-15

    Highlights: • Equilibrium, kinetic and thermodynamic of adsorption of dyes onto PDVB-IL was investigated. • PDVB-IL has a high adsorption capacity to treat dyes solution. • Higher adsorption capacity is due to the functional groups of PDVB-IL. • Molecular structure of dyes influences the adsorption capacity. -- Abstract: A novel functional ionic liquid based cross-linked polymer (PDVB-IL) was synthesized from 1-aminoethyl-3-vinylimidazolium chloride and divinylbenzene for use as an adsorbent. The physicochemical properties of PDVB-IL were investigated by Fourier transform infrared spectroscopy, scanning electron microscopy and thermogravimetric analysis. The adsorptive capacity was investigated using anionic azo dyes of orange II, sunset yellow FCF, and amaranth as adsorbates. The maximum adsorption capacity could reach 925.09, 734.62, and 547.17 mg/g for orange II, sunset yellow FCF and amaranth at 25 °C, respectively, which are much better than most of the other adsorbents reported earlier. The effect of pH value was investigated in the range of 1–8. The result shows that a low pH value is found to favor the adsorption of those anionic azo dyes. The adsorption kinetics and isotherms are well fitted by a pseudo second-order model and Langmuir model, respectively. The adsorption process is found to be dominated by physisorption. The introduction of functional ionic liquid moieties into cross-linked poly(divinylbenzene) polymer constitutes a new and efficient kind of adsorbent.

  2. Multivalent anchoring and cross-linking of mussel-inspired antifouling surface coatings.

    Science.gov (United States)

    Wei, Qiang; Becherer, Tobias; Mutihac, Radu-Cristian; Noeske, Paul-Ludwig Michael; Paulus, Florian; Haag, Rainer; Grunwald, Ingo

    2014-08-11

    In this work, we combine nature's amazing bioadhesive catechol with the excellent bioinert synthetic macromolecule hyperbranched polyglycerol (hPG) to prepare antifouling surfaces. hPG can be functionalized by different amounts of catechol groups for multivalent anchoring and cross-linking because of its highly branched architecture. The catecholic hPGs can be immobilized on various surfaces including metal oxides, noble metals, ceramics, and polymers via simple incubation procedures. The effect of the catechol amount on the immobilization, surface morphology, stability, and antifouling performance of the coatings was studied. Both anchoring and cross-linking interactions provided by catechols can enhance the stability of the coatings. When the catechol groups on the hPG are underrepresented, the tethering of the coating is not effective; while an overrepresentation of catechol groups leads to protein adsorption and cell adhesion. Thus, only a well-balanced amount of catechols as optimized and described in this work can supply the coatings with both good stability and antifouling ability.

  3. Alkaline membrane fuel cells with in-situ cross-linked ionomers

    Energy Technology Data Exchange (ETDEWEB)

    Leng, YJ; Wang, LZ; Hickner, MA; Wang, CY

    2015-01-10

    Improving cell performance and durability through both new materials and membrane electrode processing optimization is needed for the commercialization of alkaline membrane fuel cell (AMFC) technologies. In this work, we adopted an in-situ cross-linking strategy of an anion-conducting block copolymer to prepare durable ionomers for use in alkaline membrane fuel cells (AMFCs). Our goal was to use new ionomers and binders with an aim at improving long-term stability of AMFCs, especially at high operation temperatures. At 80 degrees C, AMFCs with in-situ cross-linked ionomers showed promising stability with an operating life time of more than 350 hours at 100 mA/cm(2). We found that the optimized electrode fabrication process and operating conditions can significantly improve the durability performance of AMFCs. For example, a suitable electrode binder in addition to the ion-conducting ionomer can greatly enhance the durability performance of AMFCs. Operating fuel cells under a cathode over-humification condition can also enhance the long-term stability of AMFCs. (C) 2014 Elsevier Ltd. All rights reserved.

  4. Characterization of Chemical and Physical Properties of Hydroxypropylated and Cross-linked Arrowroot (Marantha arundinacea Starch

    Directory of Open Access Journals (Sweden)

    Rijanti Rahaju Maulani

    2013-12-01

    Full Text Available The modern food industry and a variety of food products require tolerant starch as raw material for processing in a broad range of techniques, from preparation to storage and distribution. Dual modification of arrowroot starch using hydroxypropylation and cross-linking was carried out to overcome the lack of native arrowroot starch in food processing application. The modifications applied were: combined propylene oxide (8%, 10%, and 12%; sodium tri meta phosphate/STMP (1%, 2%, and 3%; and sodium tri poly phosphate/STPP (4%, 5%, and 6%. These modifications significantly affected the composition of the amylose and amylopectin and the amount of phosphorus in the granules. Higher amounts of phosphate salt gave a higher phosphorus content, which increased the degree of substitution (DS and the degree of cross-link. Arrowroot starch that was modified using a concentration of 8-10% propylene oxide and 1-2% STMP : 3-5% STPP produced a starch with < 0.4% phosphorus content. A higher concentration of propylene oxide provided a higher degree of hydroxypropyl. The changed physical properties of the modified granular arrowroot starch were examined through SEM testing, and its changed crystalline patterns through X-ray diffraction measurements. Especially, provision of a high concentration of propylene oxide (12% combined with 3% STMP : 6% STPP affected the granular morphology and the crystallinity.

  5. The Influence of Chitosan Cross-linking on the Properties of Alginate Microparticles with Metformin Hydrochloride—In Vitro and In Vivo Evaluation

    Directory of Open Access Journals (Sweden)

    Marta Szekalska

    2017-01-01

    Full Text Available Sodium alginate is a polymer with unique ability to gel with different cross-linking agents in result of ionic and electrostatic interactions. Chitosan cross-linked alginate provides improvement of swelling and mucoadhesive properties and might be used to design sustained release dosage forms. Therefore, the aim of this research was to develop and evaluate possibility of preparing chitosan cross-linked alginate microparticles containing metformin hydrochloride by the spray-drying method. In addition, influence of cross-linking agent on the properties of microparticles was evaluated. Formulation of microparticles prepared by the spray drying of 2% alginate solution cross-linked by 0.1% chitosan was characterized by good mucoadhesive properties, high drug loading and prolonged metformin hydrochloride release. It was shown that designed microparticles reduced rat glucose blood level, delayed absorption of metformin hydrochloride and provided stable plasma drug concentration. Additionally, histopathological studies of pancreas, liver and kidneys indicated that all prepared microparticles improved degenerative changes in organs of diabetic rats. Moreover, no toxicity effect and no changes in rats behavior after oral administration of chitosan cross-linked alginate microparticles were noted.

  6. The Influence of Chitosan Cross-linking on the Properties of Alginate Microparticles with Metformin Hydrochloride-In Vitro and In Vivo Evaluation.

    Science.gov (United States)

    Szekalska, Marta; Sosnowska, Katarzyna; Zakrzeska, Agnieszka; Kasacka, Irena; Lewandowska, Alicja; Winnicka, Katarzyna

    2017-01-22

    Sodium alginate is a polymer with unique ability to gel with different cross-linking agents in result of ionic and electrostatic interactions. Chitosan cross-linked alginate provides improvement of swelling and mucoadhesive properties and might be used to design sustained release dosage forms. Therefore, the aim of this research was to develop and evaluate possibility of preparing chitosan cross-linked alginate microparticles containing metformin hydrochloride by the spray-drying method. In addition, influence of cross-linking agent on the properties of microparticles was evaluated. Formulation of microparticles prepared by the spray drying of 2% alginate solution cross-linked by 0.1% chitosan was characterized by good mucoadhesive properties, high drug loading and prolonged metformin hydrochloride release. It was shown that designed microparticles reduced rat glucose blood level, delayed absorption of metformin hydrochloride and provided stable plasma drug concentration. Additionally, histopathological studies of pancreas, liver and kidneys indicated that all prepared microparticles improved degenerative changes in organs of diabetic rats. Moreover, no toxicity effect and no changes in rats behavior after oral administration of chitosan cross-linked alginate microparticles were noted.

  7. Effect of Cross-Linking and Enzymatic Hydrolysis Composite Modification on the Properties of Rice Starches

    Directory of Open Access Journals (Sweden)

    Gao-Qiang Liu

    2012-07-01

    Full Text Available Native rice starch lacks the versatility necessary to function adequately under rigorous industrial processing, so modified starches are needed to meet the functional properties required in food products. This work investigated the impact of enzymatic hydrolysis and cross-linking composite modification on the properties of rice starches. Rice starch was cross-linked with epichlorohydrin (EPI with different concentrations (0.5%, 0.7%, 0.9% w/w, on a dry starch basis, affording cross-linked rice starches with the three different levels of cross-linking that were named R1, R2, and R3, respectively. The cross-linked rice starches were hydrolyzed by α-amylase and native, hydrolyzed, and hydrolyzed cross-linked rice starches were comparatively studied. It was found that hydrolyzed cross-linked rice starches showed a lower the degree of amylase hydrolysis compared with hydrolyzed rice starch. The higher the degree of cross-linking, the higher the capacity to resist enzyme hydrolysis. Hydrolyzed cross-linked rice starches further increased the adsorptive capacities of starches for liquids and decreased the trend of retrogradation, and it also strengthened the capacity to resist shear compared to native and hydrolyzed rice starches.

  8. Density Estimation Trees in High Energy Physics

    CERN Document Server

    Anderlini, Lucio

    2015-01-01

    Density Estimation Trees can play an important role in exploratory data analysis for multidimensional, multi-modal data models of large samples. I briefly discuss the algorithm, a self-optimization technique based on kernel density estimation, and some applications in High Energy Physics.

  9. Lathyrism-induced alterations in collagen cross-links influence the mechanical properties of bone material without affecting the mineral

    Science.gov (United States)

    Paschalis, E.P.; Tatakis, D.N.; Robins, S.; Fratzl, P.; Manjubala, I.; Zoehrer, R.; Gamsjaeger, S.; Buchinger, B.; Roschger, A.; Phipps, R.; Boskey, A.L.; Dall'Ara, E.; Varga, P.; Zysset, P.; Klaushofer, K.; Roschger, P.

    2011-01-01

    In the present study a rat animal model of lathyrism was employed to decipher whether anatomically confined alterations in collagen cross-links are sufficient to influence the mechanical properties of whole bone. Animal experiments were performed under an ethics committee approved protocol. Sixty-four female (47 day old) rats of equivalent weights were divided into four groups (16 per group): Controls were fed a semi-synthetic diet containing 0.6% calcium and 0.6% phosphorus for 2 or 4 weeks and β-APN treated animals were fed additionally with β-aminopropionitrile (0.1% dry weight). At the end of this period the rats in the four groups were sacrificed, and L2–L6 vertebra were collected. Collagen cross-links were determined by both biochemical and spectroscopic (Fourier transform infrared imaging (FTIRI)) analyses. Mineral content and distribution (BMDD) were determined by quantitative backscattered electron imaging (qBEI), and mineral maturity/crystallinity by FTIRI techniques. Micro-CT was used to describe the architectural properties. Mechanical performance of whole bone as well as of bone matrix material was tested by vertebral compression tests and by nano-indentation, respectively. The data of the present study indicate that β-APN treatment changed whole vertebra properties compared to non-treated rats, including collagen cross-links pattern, trabecular bone volume to tissue ratio and trabecular thickness, which were all decreased (p < 0.05). Further, compression tests revealed a significant negative impact of β-APN treatment on maximal force to failure and energy to failure, while stiffness was not influenced. Bone mineral density distribution (BMDD) was not altered either. At the material level, β-APN treated rats exhibited increased Pyd/Divalent cross-link ratios in areas confined to a newly formed bone. Moreover, nano-indentation experiments showed that the E-modulus and hardness were reduced only in newly formed bone areas under the influence

  10. Alkaline battery containing a separator of a cross-linked copolymer of vinyl alcohol and unsaturated carboxylic acid

    Science.gov (United States)

    Hsu, L. C.; Philipp, W. H.; Sheibley, D. W.; Gonzalez-Sanabria, O. D. (Inventor)

    1985-01-01

    A battery separator for an alkaline battery is described. The separator comprises a cross linked copolymer of vinyl alcohol units and unsaturated carboxylic acid units. The cross linked copolymer is insoluble in water, has excellent zincate diffusion and oxygen gas barrier properties and a low electrical resistivity. Cross linking with a polyaldehyde cross linking agent is preferred.

  11. ROLE OF CORNEAL COLLAGEN CROSS LINKING IN KERATOCONUS

    Directory of Open Access Journals (Sweden)

    Atul

    2015-09-01

    Full Text Available To evaluate the outcome of collagen cross linkage using riboflavin 0.1% and ultraviolet A radiation of a wavelength 370nm . PURPOSE : To determine the effect of collagen cross linking for keratoconus on pachymetry , corneal topography, uncorrected visual acuity, specular count, IOP at 1, 3, 6 months . METHODS : The current study was designed as a prospective interventional trial of corneal collagen cross - linking in subjects with progressive keratoconus between a period of J anuary 2013 to J uly 2014 including 50 eyes of 30 patients. This study rece ived approval from Ethics committee. Informed written consent was obtained from all patients prior to treatment. RESULTS: Mean follow up period of 6 months. There was statistically significant decline in effective k readings from mean pre op (51.7D to pos t op value (49.65D . Pachymetry showed initial increase post operatively followed by reduction in corneal thickness in 3 month s follow up , followed by gradual increase in thickness over a period of 6 months though it was not equivalent to pre - operative values. paired t test p value was 0.00 1 in 1 n 3 month and 0. 043 in 6 month, concluding significant reduction in early post op period with im provement over time . Specular count reduced from pre - op (2673.80 levels to post - op (2654.60 levels ,the reduction in specular count was not statistically significant P value (0.014 The uncorrected visual acuity showed decrease in refractive error with in crease in visual acuity gradually over 6 months, log MAR scale visual acuity was used for statistical analysis with P value (0.001 which was statistically significant .visual acuity improved by 1.5 lines in snellens equivalence or from 0.5 to 0.4 in log MA R char y ± 20cells/mm 3 , P value(0. 001 . IOP statically show ed no significant change in pre - operative and post operatively , paired t test p value was 0. 44 showing it was not significant . CONCLUSIONS : 1. Visual acuity improved in

  12. The theory and art of corneal cross-linking

    Directory of Open Access Journals (Sweden)

    Rebecca McQuaid

    2013-01-01

    Full Text Available Before the discovery of corneal cross-linking (CXL, patients with keratoconus would have had to undergo corneal transplantation, or wear rigid gas permeable lenses (RGPs that would temporarily flatten the cone, thereby improving the vision. The RGP contact lens (CL would not however alter the corneal stability and if the keratoconus was progressive, the continued steepening of the cone would occur under the RGP CL. To date, the Siena Eye has been the largest study to investigate long term effects of standard CXL. Three hundred and sixty-three eyes were treated and monitored over 4 years, producing reliable long-term results proving long-term stability of the cornea by halting the progression of keratoconus, and proving the safety of the procedure. Traditionally, CXL requires epithelial removal prior to corneal soakage of a dextran-based 0.1% riboflavin solution, followed by exposure of ultraviolet-A (UV-A light for 30 min with an intensity of 3 mW/cm2. A series of in vitro investigations on human and porcine corneas examined the best treatment parameters for standard CXL, such as riboflavin concentration, intensity, wavelength of UV-A light, and duration of treatment. Photochemically, CXL is achieved by the generation of chemical bonds within the corneal stroma through localized photopolymerization, strengthening the cornea whilst minimizing exposure to the surrounding structures of the eye. In vitro studies have shown that CXL has an effect on the biomechanical properties of the cornea, with an increased corneal rigidity of approximately 70%. This is a result of the creation of new chemical bonds within the stroma.

  13. Transglutaminases: widespread cross-linking enzymes in plants.

    Science.gov (United States)

    Serafini-Fracassini, Donatella; Del Duca, Stefano

    2008-08-01

    Transglutaminases have been studied in plants since 1987 in investigations aimed at interpreting some of the molecular mechanisms by which polyamines affect growth and differentiation. Transglutaminases are a widely distributed enzyme family catalysing a myriad of biological reactions in animals. In plants, the post-translational modification of proteins by polyamines forming inter- or intra-molecular cross-links has been the main transglutaminase reaction studied. The few plant transglutaminases sequenced so far have little sequence homology with the best-known animal enzymes, except for the catalytic triad; however, they share a possible structural homology. Proofs of their catalytic activity are: (a) their ability to produce glutamyl-polyamine derivatives; (b) their recognition by animal transglutaminase antibodies; and (c) biochemical features such as calcium-dependency, etc. However, many of their fundamental biochemical and physiological properties still remain elusive. It has been detected in algae and in angiosperms in different organs and sub-cellular compartments, chloroplasts being the best-studied organelles. Possible roles concern the structural modification of specific protein substrates. In chloroplasts, transglutaminases appear to stabilize the photosynthetic complexes and Rubisco, being regulated by light and other factors, and possibly exerting a positive effect on photosynthesis and photo-protection. In the cytosol, they modify cytoskeletal proteins. Preliminary reports suggest an involvement in the cell wall construction/organization. Other roles appear to be related to fertilization, abiotic and biotic stresses, senescence and programmed cell death, including the hypersensitive reaction. The widespread occurrence of transglutaminases activity in all organs and cell compartments studied suggests a relevance for their still incompletely defined physiological roles. At present, it is not possible to classify this enzyme family in plants owing to

  14. Institute for High Energy Density Science

    Energy Technology Data Exchange (ETDEWEB)

    Wootton, Alan [Univ. of Texas, Austin, TX (United States)

    2017-01-13

    The project objective was for the Institute of High Energy Density Science (IHEDS) at the University of Texas at Austin to help grow the High Energy Density (HED) science community, by connecting academia with the Z Facility (Z) and associated staff at Sandia National Laboratories (SNL). IHEDS was originally motivated by common interests and complementary capabilities at SNL and the University of Texas System (UTX), in 2008.

  15. Investigation of cross-linking poly(methyl methacrylate) as a guiding material in block copolymer directed self-assembly

    Science.gov (United States)

    Seidel, Robert; Rincon Delgadillo, Paulina; Ramirez-Hernandez, Abelardo; Wu, Hengpeng; Her, Youngjun; Yin, Jian; Nealey, Paul; de Pablo, Juan; Gronheid, Roel

    2014-03-01

    Directed self-assembly (DDSA) of block copolymers ((BCP) is attracting a growing amount of interest as a techhnique to expand traditional lithography beyond its current limits. It has reecently been demonstrated that chemoepitaxy can be used to successfully ddirect BCP assembly to form large arrays off high-density features. The imec DSA LiNe flow uses lithography and trim-etch to produce a "prepattern" of cross-linked polystyrene (PS) stripes, which in turn guide the formation of assembled BCPP structures. Thhe entire process is predicated on the preferential interaction of the respective BCP domains with particular regionss of the underlying prepattern. The use of polystyrene as the guiding material is not uniquely required, however, and in fact may not even be preferable. This study investigates an alternate chemistry -- crosslinked poly(methyl methacrylate), X-PMMA, -- as the underlying polymer mat, providing a route to higher auto-affinity and therefore a stronger guiding ability. In addition to tthe advantages of the chemistry under investigation, this study explores the broader theme of extending BCP DSA to other materials.

  16. Shape-memory behavior of cross-linked semi-crystalline polymers and their blends

    Directory of Open Access Journals (Sweden)

    I. Kolesov

    2015-03-01

    Full Text Available The present study deals with thermally induced one-way and invertible two-way shape-memory effect (SME in covalent networks on the basis of crystallizable (copolymers and their blends and is an attempt to generalize the results of own investigation received by the authors in the last ten years. The main focus of work clearly lies on research of covalently crosslinked binary and ternary blends having two and three crystalline phases with different thermal stability, respectively. The existence of two or three crystalline phases possessing different melting and crystallization temperatures in heterogeneous polymer networks can lead to triple-shape or even quadruple-shape behavior of such networks. However, the performed investigations point to crucial effect of phase morphology of crosslinked polymer blends on multiplicity of their shapememory behavior beside the influence of blend content, crystallinity and cross-link density of blend phases as well as of processing conditions. For instance, triple-shape memory behavior in binary blends can be realized only if the continuous phase has a lower melting temperature than the dispersed phase. Cross-linked polymer blends are a facile alternative to expensive and complex synthesis of interpenetrating or block-copolymer networks used for shape memory polymers. In addition to findings of experimental investigation of SME in crystallizable covalent polymer networks, the results of modeling their shape-memory behavior on the basis of self-developed physically reasonable model have been briefly described and discussed. Thereby, good accordance between results of theory and experiment was achieved with physically justified fitting parameters.

  17. Template-assisted fabrication of free-standing nanorod arrays of a hole-conducting cross-linked triphenylamine derivative: toward ordered bulk-heterojunction solar cells.

    Science.gov (United States)

    Haberkorn, Niko; Gutmann, Jochen S; Theato, Patrick

    2009-06-23

    Free-standing nanorod arrays of a thermally cross-linked semiconducting triphenylamine were fabricated on conductive ITO/glass substrates via an anodic aluminum oxide (AAO) template-assisted approach. By using a solution wetting method combined with a subsequent thermal imprinting step to fill the nanoporous structure of the template with a cross-linkable triphenylamine derivative, a polymeric replication of the AAO was obtained after thermal curing and selective removal of the template. To obtain well-aligned and free-standing nanorod arrays, aggregation and collapse of the nanorods were prevented by optimizing their aspect ratio and applying a freeze-drying technique to remove the aqueous medium after the etching step. Because of their electrochemical properties and their resistance against organic solvents after curing, these high density nanorod arrays have potential application in organic photovoltaics.

  18. Molecular dynamics simulation of cross-linked urea-formaldehyde polymers for self-healing nanocomposites: prediction of mechanical properties and glass transition temperature.

    Science.gov (United States)

    Arab, Behrouz; Shokuhfar, Ali

    2013-11-01

    Urea-formaldehyde polymers, which are utilized in the adhesives industry, have recently been shown to be suitable materials for synthesizing micro/nanocapsules for use in self-healing (nano)composites. In this study, molecular dynamics was employed to simulate the process in which urea and formaldehyde are cross-linked via methylene and ether cross linkers, and to study the structure and mechanical/thermal properties of simulated poly(urea-formaldehyde)s (PUFs). The elastic stiffness constants of the simulated materials were calculated using the constant-strain (static) method. A temperature cycle was applied to the cross-linked PUFs, and the glass transition behavior of each material was investigated through the mean squared displacement (MSD) and temperature evolution of the energy and the specific volume of the polymer. The simulation results confirmed that there was considerable improvement in the properties of the poly(UF) materials upon cross linking. The radial distribution function was also used to study the local structures of the polymers, and this revealed that increasing the temperature and cross linking density results in a significant drop in hydrogen bonding intensity in the cross-linked PUF systems.

  19. Strongly Interacting Matter at High Energy Density

    Energy Technology Data Exchange (ETDEWEB)

    McLerran,L.

    2008-09-07

    This lecture concerns the properties of strongly interacting matter (which is described by Quantum Chromodynamics) at very high energy density. I review the properties of matter at high temperature, discussing the deconfinement phase transition. At high baryon density and low temperature, large N{sub c} arguments are developed which suggest that high baryonic density matter is a third form of matter, Quarkyonic Matter, that is distinct from confined hadronic matter and deconfined matter. I finally discuss the Color Glass Condensate which controls the high energy limit of QCD, and forms the low x part of a hadron wavefunction. The Glasma is introduced as matter formed by the Color Glass Condensate which eventually thermalizes into a Quark Gluon Plasma.

  20. SYNTHESIS AND CATALYTIC PROPERTIES OF CROSS-LINKED HYDROPHOBICALLY ASSOCIATING POLY(ALKYLMETHYLDIALLYLAMMONIUM BROMIDES)

    NARCIS (Netherlands)

    WANG, GJ; ENGBERTS, JBFN

    1994-01-01

    Cross-linked, hydrophobically associating homo- and copolymers were synthesized by free-radical cyclo(co)polymerization of alkylmethyldiallylammonium bromide monomers with a small amount of N,N'-methylenebisacrylamide in aqueous solution using ammonium persulfate as the initiator. The cross-linked h

  1. Rheological properties of dispersions of enzymatically cross-linked apo-α-lactalbumin

    NARCIS (Netherlands)

    Saricay, Yunus; Wierenga, Peter A.; Vries, de Renko

    2016-01-01

    The enzymatic cross-linking of apo-α-lactalbumin (α-LA) with horseradish peroxidase (HRP) leads to the formation of hydrophilic protein aggregates with controlled size and architecture. We explore the rheological properties of dispersions of these HRP-cross-linked α-LA aggregates with a hydrodyna

  2. PREPARATION OF NOVEL METALLIC AND BIMETALLIC CROSS-LINKED POLY (VINYL ALCOHOL) NANOCOMPOSITES UNDER MICROWAVE IRRADIATION

    Science.gov (United States)

    A facile method utilizing microwave irradiation is described that accomplishes the cross-linking reaction of PVA with metallic and bimetallic systems. Nanocomposites of PVA-cross-linked metallic systems such as Pt, Cu, and In and bimetallic systems such as Pt-In, Ag-Pt, Pt-Fe, Cu...

  3. NOVEL METALLIC AND BIMETALLIC CROSS-LINKED POLY (VINYL ALCOHOL) NANOCOMPOSITES PREPARED UNDER MICROWAVE IRRADIATION

    Science.gov (United States)

    A facile microwave irradiation approach that results in a cross-linking reaction of poly (vinyl alcohol) (PVA) with metallic and bimetallic systems is described. Nanocomposites of PVA cross-linked metallic systems such as Pt, Cu, and In and bimetallic systems such as Pt-In, Ag-P...

  4. Quantification of carboxyl groups in carbodiimide cross-linked collagen sponges

    NARCIS (Netherlands)

    Everaerts, Frank; Torrianni, Mark; Hendriks, Marc; Feijen, Jan

    2007-01-01

    Glutaraldehyde (GA) fixation of bioprosthetic tissue is a well adapted technique, with commercial products on the market for almost 40 years. Amine groups present in tissue react with GA to form different types of cross-links. An estimation of the degree of cross-linking of the tissue can be obtaine

  5. Glucose-mediated cross-linking of collagen in rat tendon and skin

    NARCIS (Netherlands)

    Mentink, CJAL; Hendriks, M; Levels, AAG; Wolffenbuttel, BHR

    2002-01-01

    Back-ground: Cross-linking of macromolecules like collagen plays an important role in the development of complications in diabetes and ageing. One of the underlying mechanisms of this cross-linking is the formation of advanced glycation endproducts (AGEs). Methods: In this study, we assessed the use

  6. Peroxidase-mediated cross-linking of a tyrosine-containing peptide with ferulic acid

    NARCIS (Netherlands)

    Oudgenoeg, G.; Hilhorst, R.; Piersma, S.R.; Boeriu, C.G.; Gruppen, H.; Hessing, M.; Voragen, A.G.J.; Laane, C.

    2001-01-01

    The tyrosine-containing peptide Gly-Tyr-Gly (GYG) was oxidatively cross-linked by horseradish peroxidase in the presence of hydrogen peroxide. As products, covalently coupled di- to pentamers of the peptide were identified by LC-MS. Oxidative cross-linking of ferulic acid with horseradish peroxidase

  7. Biodegradation of differently cross-linked collagen membranes: an experimental study in the rat.

    NARCIS (Netherlands)

    Rothamel, D.; Schwarz, F.; Sager, M.; Herten, M. van; Sculean, A.; Becker, J.M.

    2005-01-01

    The aim of the present study was to compare the biodegradation of differently cross-linked collagen membranes in rats. Five commercially available and three experimental membranes (VN) were included: (1) BioGide (BG) (non-cross-linked porcine type I and III collagens), (2) BioMend (BM), (3) BioMendE

  8. Thermally cross-linked superparamagnetic iron oxide nanoparticles: synthesis and application as a dual imaging probe for cancer in vivo.

    Science.gov (United States)

    Lee, Haerim; Yu, Mi Kyung; Park, Sangjin; Moon, Sungmin; Min, Jung Jun; Jeong, Yong Yeon; Kang, Hae-Won; Jon, Sangyong

    2007-10-24

    We report the fabrication and characterization of thermally cross-linked superparamagnetic iron oxide nanoparticles (TCL-SPION) and their application to the dual imaging of cancer in vivo. Unlike dextran-coated cross-linked iron oxide nanoparticles, which are prepared by a chemical cross-linking method, TCL-SPION are prepared by a simple, thermal cross-linking method using a Si-OH-containing copolymer. The copolymer, poly(3-(trimethoxysilyl)propyl methacrylate-r-PEG methyl ether methacrylate-r-N-acryloxysuccinimide), was synthesized by radical polymerization and used as a coating material for as-synthesized magnetite (Fe3O4) SPION. The polymer-coated SPION was further heated at 80 degrees C to induce cross-linking between the -Si(OH)3 groups in the polymer chains, which finally generated TCL-SPION bearing a carboxyl group as a surface functional group. The particle size, surface charge, presence of polymer-coating layers, and the extent of thermal cross-linking were characterized and confirmed by various measurements, including dynamic light scattering, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. The carboxyl TCL-SPION was converted to amine-modified TCL-SPION and then finally to Cy5.5 dye-conjugated TCL-SPION for use in dual (magnetic resonance/optical) in vivo cancer imaging. When the Cy5.5 TCL-SPION was administered to Lewis lung carcinoma tumor allograft mice by intravenous injection, the tumor was unambiguously detected in T2-weighted magnetic resonance images as a 68% signal drop as well as in optical fluorescence images within 4 h, indicating a high level of accumulation of the nanomagnets within the tumor site. In addition, ex vivo fluorescence images of the harvested tumor and other major organs further confirmed the highest accumulation of the Cy5.5 TCL-SPION within the tumor. It is noteworthy that, despite the fact that TCL-SPION does not bear any targeting ligands on its surface, it was highly effective for tumor

  9. Investigation of anisotropic thermal transport in cross-linked polymers

    Science.gov (United States)

    Simavilla, David Nieto

    Thermal transport in lightly cross-linked polyisoprene and polybutadine subjected to uniaxial elongation is investigated experimentally. We employ two experimental techniques to assess the effect that deformation has on this class of materials. The first technique, which is based on Forced Rayleigh Scattering (FRS), allows us to measure the two independent components of the thermal diffusivity tensor as a function of deformation. These measurements along with independent measurements of the tensile stress and birefringence are used to evaluate the stress-thermal and stress-optic rules. The stress-thermal rule is found to be valid for the entire range of elongations applied. In contrast, the stress-optic rule fails for moderate to large stretch ratios. This suggests that the degree of anisotropy in thermal conductivity depends on both orientation and tension in polymer chain segments. The second technique, which is based on infrared thermography (IRT), allows us to measure anisotropy in thermal conductivity and strain induced changes in heat capacity. We validate this method measurements of anisotropic thermal conductivity by comparing them with those obtained using FRS. We find excellent agreement between the two techniques. Uncertainty in the infrared thermography method measurements is estimated to be about 2-5 %. The accuracy of the method and its potential application to non-transparent materials makes it a good alternative to extend current research on anisotropic thermal transport in polymeric materials. A second IRT application allows us to investigate the dependence of heat capacity on deformation. We find that heat capacity increases with stretch ratio in polyisoprene specimens under uniaxial extension. The deviation from the equilibrium value of heat capacity is consistent with an independent set of experiments comparing anisotropy in thermal diffusivity and conductivity employing FRS and IRT techniques. We identify finite extensibility and strain

  10. Preparation of Cross-Linked Glucoamylase Aggregates Immobilization by Using Dextrin and Xanthan Gum as Protecting Agents

    Directory of Open Access Journals (Sweden)

    Xiao-Dong Li

    2016-05-01

    Full Text Available In this paper glucoamylase from Aspergillus niger was immobilized by using a modified version of cross-linked enzyme aggregates (CLEA. The co-aggregates were cross-linked with glutaraldehyde; meanwhile dextrin and xanthan gum as protecting agents were added, which provides high affinity with the enzyme molecules. The immobilized glucoamylase was stable over a broad range of pH (3.0–8.0 and temperature (55–75 °C; dependence shows more catalytic activity than a free enzyme. The thermostability, kinetic behavior, and first-order inactivation rate constant (ki were investigated. The two types of protector made the immobilized glucoamylase more robust than the free form. Both of the immobilized enzymes have excellent recyclability, retaining over 45% of the relative activity after 24 runs. In addition, immobilized enzymes reduced only 40% of the initial activity after three months by the storability measure, indicating high activity.

  11. Determination of the 1-ethyl-3-[(3-dimethylamino)propyl]-carbodiimide- induced cross-link between the beta and epsilon subunits of Escherichia coli F1-ATPase.

    Science.gov (United States)

    Dallmann, H G; Flynn, T G; Dunn, S D

    1992-09-15

    The zero-length cross-link between the inhibitory epsilon subunit and one of three catalytic beta subunits of Escherichia coli F1-ATPase (alpha 3 beta 3 gamma delta epsilon), induced by a water-soluble carbodiimide, 1-ethyl-3-[(3-dimethylamino) propyl]-carbodiimide (EDC), has been determined at the amino acid level. Lability of cross-linked beta-epsilon to base suggested an ester cross-link rather than the expected amide. A 10-kDa cross-linked CNBr fragment derived from beta-epsilon was identified by electrophoresis on high percentage polyacrylamide gels. Sequence analysis of this peptide revealed the constituent peptides to be Asp-380 to Met-431 of beta and Glu-96 to Met-138 of epsilon. Glu-381 of beta was absent from cycle 2 indicating that it was one of the cross-linked residues, but no potential cross-linked residue in epsilon was identified in this analysis. A form of epsilon containing a methionine residue in place of Val-112 (epsilon V112M) was produced by site-directed mutagenesis. epsilon V112M was incorporated into F1-ATPase which was then cross-linked with EDC. An 8-kDa cross-linked CNBr fragment of beta-epsilon V112M was shown to contain the peptide of epsilon between residues Glu-96 and Met-112 and the peptide of beta between residues Asp-380 and Met-431. Again residue Glu-381 of beta was notably reduced and no missing residue from the epsilon peptide could be identified, but the peptide sequence limited the possible choices to Ser-106, Ser-107, or Ser-108. Furthermore, an epsilon mutant in which Ser-108 was replaced by cysteine could no longer be cross-linked to a beta subunit in F1-ATPase by EDC. Both mutant forms of epsilon supported growth of an uncC-deficient E. coli strain and inhibited F1-ATPase. These results indicate that the EDC-induced cross-link between the beta and epsilon subunits of F1-ATPase is an ester linkage between beta-Glu-381 and, likely, epsilon-Ser-108. As these residues must be located immediately adjacent to one another in F1

  12. Spin polarization in high density quark matter

    DEFF Research Database (Denmark)

    Bohr, Henrik; Panda, Prafulla K.; Providênci, Constanca

    2013-01-01

    We investigate the occurrence of a ferromagnetic phase transition in high density hadronic matter (e.g., in the interior of a neutron star). This could be induced by a four-fermion interaction analogous to the one which is responsible for chiral symmetry breaking in the Nambu-Jona-Lasinio model......, to which it is related through a Fierz transformation. Flavor SU(2) and flavor SU(3) quark matter are considered. A second-order phase transition is predicted at densities about 5 times the normal nuclear matter density. It is also found that in flavor SU(3) quark matter, a first-order transition from...

  13. Assessment of protein function following cross-linking by alpha-dicarbonyls.

    Science.gov (United States)

    Miller, Antonia G; Gerrard, Juliet A

    2005-06-01

    Protein cross-linking via the Maillard reaction with alpha-dicarbonyl compounds has been the subject of intense scrutiny in the literature. We report here a study of the impact of this cross-linking on enzyme function. Protein function following glycation was examined by treating ribonuclease A with methylglyoxal, glyoxal, and diacetyl, which cross-linked the enzyme and impaired its activity. The effects of two reported Maillard reaction inhibitors, aminoguanidine and 3,5-dimethylpyrazole-1-carboxamidine, on the cross-linking reaction were assessed, with a parallel measurement of the effect on enzyme activity. The results demonstrate that preventing protein cross-linking does not necessarily preserve enzyme activity. These results cast doubt on the likely efficacy of some purported antiaging compounds in vivo.

  14. Characteristic of hyaluronic acid derivative films cross-linked by polyethylene glycol of low water content

    Institute of Scientific and Technical Information of China (English)

    Chen Jinghua; Chen Jingtao; Xu Zheng; Gu Qisheng

    2008-01-01

    Objective: To test the characteristics of byaluronic acid (HA) derivative cross-linked by polyethylene glycol films of low water content. Methods: The cross-linked HA film with 200 μm thickness was got at atmospheric pressure at 25℃ for 5 d. After dried, cross-linked films of 10 mm×10 mm were weighed and immersed in phosphate buffered saline (PBS pH 7.45) at 37℃ for 24 h. Then the solution fraction and water content were estimated. Meanwhile, cross-linked HA derivative films were immersed in phosphate buffered saline (PBS: pH 7.45) at 37℃ for determined time and then implanted subcutaneously in the back of white rats to test in vitro or in vivo degradation characteristic. Results and Conclusion: HA hydrogel cross-linked by polyethylene glycol with water content is as low as 60% and this kind of HA derivative has a slow degradation rate.

  15. Theoretical studies of the functional role of the cross-linked histidine-tyrosine copper-B ligand of cytochrome c oxidase

    Science.gov (United States)

    McDonald, William J.

    In the present work density functional theory calculations were performed to explore the vibrational and electronic spectral changes associated with proton and electron transfer from the CuB center at the active site of cytochrome c oxidase that lead to the formation of either the PR or PM intermediates in the catalytic reduction of dioxygen to water. Furthermore, the thermodynamics of proton and electron transfer from the cross-linked histidine-tyrosine Cu B ligand were explored to assess the possible role of this ligand as a proton and/or electron donor during enzymatic turnover. Characteristic calculated cross-linked imidazole-phenolate and imidazole-phenoxyl radical vibrational frequencies and isotope shifts are in good agreement with the vibrational spectra of the PR and PM intermediates of the bo3 quinol oxidase from E. coli and R. sphaeroides and P. denitrificans suggesting that the Y244 (bovine numbering) is deprotonated in the PR intermediate, and is a tyrosyl radical in P M. Furthermore, using isodesmic reactions, the cross-linked phenol is found to be a significantly stronger acid than an unmodified phenol in the gas-phase, and likely in the inhomogeneous low-dielectric environment of the membrane bound enzyme, supporting the conclusion that the cross-linked tyrosine is a proton donor during enzymatic turnover. Time-dependent density functional theory calculations qualitatively reproduce the red-shift in the UV/visible absorption spectrum of a cross-linked imidazole-phenolate anion compared to the imidazole-phenol. Furthermore, the unique ˜500 nm absorption of a cross-linked imidazole-phenoxyl radical is correctly predicted using TDDFT and may be assigned as an imidazole-phenoxyl radical pi-to-pi* transition. Furthermore, this absorption is predicted in the spectrum of a Cu2+-imidazole-phenoxyl biradical model.

  16. Disuccinimidyl suberate cross-linked hemoglobin as a novel red blood cell substitute

    Institute of Scientific and Technical Information of China (English)

    LU; Xiuling; ZHENG; Chunyang; XU; Yuhong; SU; Zhiguo

    2005-01-01

    Disuccinimidyl suberate (DSS) intramolecularly cross-linked hemoglobin (Hb) was developed as a novel red blood cell substitute. A multi-angle laser light scattering detector coupled with size exclusion HPLC was applied to determine the molecular weight of the modified Hb. SDS-PAGE was also used as a complement. It was proved that 83.8% of the product was intramolecularly cross-linked Hb with weight-average molecular weights (Mw) of 67.5 kD, 12% was dimeric Hb with Mw of 146.6 kD, and 4.2% was trimeric Hb with Mw of 306.4 kD. The tetramer structure of the cross-linked Hb was stable as shown in size-exclusion chromatography using a mobile phase containing 1 mol/L MgCl2. Analysis by LC-MS demonstrated that the reaction of DSS with Hb mainly took place between the twoα subunits within a Hb molecule, resulting in stabilization of the tetramer structure. However, the cross-linking was not site-specific. The P50 of the cross-linked Hb decreased from 21.8 mmHg to 14.3 mmHg, and the Hill coefficient decreased from 2.22 to 1.41. Result of isoelectric focusing showed that the pI of DSS cross-linked Hb was in the range of 4.6-5.2, similar to that of serum albumin. The safety of DSS cross-linked Hb was favored by animal tests on rats and guinea pigs. Exchange transfusion experiment with DSS cross-linked Hb using rats as a model indicated no pressor effect or other significant side effects. The characteristics and properties of DSS cross-linked Hb were also compared with that of diaspirin cross-linked Hb reported in the literature.

  17. The high density Z-pinch

    Energy Technology Data Exchange (ETDEWEB)

    McCall, G.H.

    1988-01-01

    During the past few years techniques have been developed for producing pinches in solid deuterium. The conditions which exist in these plasmas are quiet different from those produced earlier. The pinch is formed from a fiber of solid deuterium rather than from a low density gas, and the current is driven by a low impedance, high voltage pulse generator. Because of the high initial density, it is not necessary to compress the pinch to reach thermonuclear conditions, and the confinement time required for energy production is much shorter than for a gas. The experimental results, which have been verified by experiments performed at higher current were quite surprising and encouraging. The pinch appeared to be stable for a time much longer than the Alfven radial transit time. In this paper, however, I argue that the pinch is not strictly stable, but it does not appear to disassemble in a catastrophic fashion. It appears that there may be a distinction between stability and confinement in the high density pinch. In the discussion below I will present the status of the high density Z-pinch experiments at laboratories around the world, and I will describe some of the calculational and experimental results. I will confine my remarks to recent work on the high density pinch. 17 refs. 10 figs.

  18. Mechanically Strong, Polymer Cross-linked Aerogels (X-Aerogels)

    Science.gov (United States)

    Leventis, Nicholas

    2006-01-01

    Aerogels comprise a class of low-density, high porous solid objects consisting of dimensionally quasi-stable self-supported three-dimensional assemblies of nanoparticles. Aerogels are pursued because of properties above and beyond those of the individual nanoparticles, including low thermal conductivity, low dielectric constant and high acoustic impedance. Possible applications include thermal and vibration insulation, dielectrics for fast electronics, and hosting of functional guests for a wide variety of optical, chemical and electronic applications. Aerogels, however, are extremely fragile materials, hence they have found only limited application in some very specialized environments, for example as Cerenkov radiation detectors in certain types of nuclear reactors, aboard spacecraft as collectors of hypervelocity particles (refer to NASA's Stardust program) and as thermal insulators on planetary vehicles on Mars (refer to Sojourner Rover in 1997 and Spirit and Opportunity in 2004). Along these lines, the X-Aerogel is a new NASA-developed strong lightweight material that has resolved the fragility problem of traditional (native) aerogels. X-Aerogels are made by applying a conformal polymer coating on the surfaces of the skeletal nanoparticles of native aerogels (see Scanning Electron Micrographs). Since the relative amounts of the polymeric crosslinker and the backbone are comparable, X-Aerogels can be viewed either as aerogels modified by the templated accumulation of polymer on the skeletal nanoparticles, or as nanoporous polymers made by remplated casting of polymer on a nanostructured framework. The most striking feature of X-Aerogels is that for a nominal 3-fold increase in density (still a ultralighweight material), the mechanical strength can be up to 300 times higher than the strength of the underlying native aerogel. Thus, X-Aerogels combine a multiple of the specific compressive strength of steel, with the the thermal conductivity of styrofoam. X

  19. Evaluation of cross-linked aggregates from purified Bacillus subtilis levansucrase mutants for transfructosylation reactions

    Directory of Open Access Journals (Sweden)

    Munguia Agustin

    2009-07-01

    Full Text Available Abstract Background Increasing attention has been focused on inulin and levan-type oligosaccharides, including fructosyl-xylosides and other fructosides due to their nutraceutical properties. Bacillus subtilis levansucrase (LS catalyzes the synthesis of levan from sucrose, but it may also transfer the fructosyl moiety from sucrose to acceptor molecules included in the reaction medium. To study transfructosylation reactions with highly active and robust derivatives, cross-linked enzyme aggregates (CLEAs were prepared from wild LS and two mutants. CLEAs combine the catalytic features of pure protein preparations in terms of specific activity with the mechanical behavior of industrial biocatalysts. Results Two types of procedures were used for the preparation of biocatalysts from purified wild type LS (WT LS B. subtilis and the R360K and Y429N LS mutants: purified enzymes aggregated with glutaraldehyde (cross-linked enzyme aggregates: CLEAs, and covalently immobilized enzymes in Eupergit C®. The biocatalysts were characterized and used for fructoside synthesis using xylose as an acceptor model. CLEAs were able to catalyze the synthesis of fructosides as efficiently as soluble enzymes. The specific activity of CLEAs prepared from wild type LS (44.9 U/mg of CLEA, R360K (56.5 U/mg of CLEA and Y429N (1.2 U/mg of CLEA mutants were approximately 70, 40 and 200-fold higher, respectively, than equivalent Eupergit C® immobilized enzyme preparations (U/mg of Eupergit, where units refer to global LS activity. In contrast, the specific activity of the free enzymes was 160, 171.2 and 1.5 U/mg of protein, respectively. Moreover, all CLEAs had higher thermal stability than corresponding soluble enzymes. In the long term, the operational stability was affected by levan synthesis. Conclusion This is the first report of cross-linked transglycosidases aggregates. CLEAs prepared from purified LS and mutants have the highest specific activity for immobilized

  20. Cooperative assembly of Zn cross-linked artificial tripeptides with pendant hydroxyquinoline ligands.

    Science.gov (United States)

    Zhang, Meng; Gallagher, Joy A; Coppock, Matthew B; Pantzar, Lisa M; Williams, Mary Elizabeth

    2012-11-01

    An artificial peptide with three pendant hydroxyquinoline (hq) ligands on a palindromic backbone was designed and used to form multimetallic assemblies. Reaction of the tripeptide with zinc acetate led to a highly fluorescent tripeptide duplex with three Zn(II) coordinative cross-links. The binding process was monitored using spectrophotometric absorbance and emission titrations; NMR spectroscopy and mass spectrometry confirmed the identity and stoichiometry of the product structure. Titrations monitoring duplex formation of the zinc-tripeptide structure had a sigmoidal shape, equilibrium constant larger than the monomeric analogue, and a Hill coefficient >1, all of which indicate positive cooperativity. Photophysical characterization of the quantum yield, excited state lifetime, and polarization anisotropy are compared with the monometallic zinc-hq analogue. A higher than expected quantum yield for the trimetallic complex suggests a structure in which the central chromophore is shielded from solvent by π-stacking with neighboring Zn(II) complexes.

  1. A core cross-linked polymeric micellar platium(IV) prodrug with enhanced anticancer efficiency.

    Science.gov (United States)

    Hou, Jie; Shang, Jincai; Jiao, Chengbin; Jiang, Peiyue; Xiao, Huijie; Luo, Lan; Liu, Tongjun

    2013-07-01

    A core cross-linked polymeric micellar cisplatin(IV) conjugate prodrug is prepared by attaching the cisplatin(IV) to mPEG-b-PLL biodegradable copolymers to form micellar nanoparticles that can disintegrate to release the active anticancer agent cisplatin(II) in a mild reducing environment. Moreover, in vitro studies show that this cisplatin(IV) conjugate prodrug displays enhanced cytotoxicity against HepG2 cancer cells compared with cisplatin(II). Further studies demonstrate that the high cellular uptake and platinum-DNA adduct of this cisplatin(IV) conjugate prodrug can induce more cancer-cell apoptosis than cisplatin(II), which is responsible for its enhanced anticancer activity.

  2. Fabrication and morphology of spongelike polymer material based on cross-linked sulfonated polystyrene particles.

    Science.gov (United States)

    Ji, Xiang; Wang, Mozhen; Xu, Dezhi; Ge, Xuewu; Liu, Huarong; Tang, Tao

    2012-04-03

    A novel spongelike polymer material has been fabricated by γ-ray induced polymerization of methylmethacrylate (MMA) in an emulsion containing cross-linked sulfonated polystyrene (CSP) particles. Scanning electron microscopy (SEM) images reveal that the spongelike structure is made up of interlinked nanosized PMMA particles with micrometer-sized CSP-PMMA particles embedded inside. The nitrogen adsorption isotherm discloses that the spongelike material has a high specific surface area of 29 m(2)/g and a narrow pore size distribution of 60-120 nm. The formation mechanism is discussed in this paper, which indicates that the key steps to form the spongelike material include a Pickering emulsion stabilized by the CSP particles, followed by the swelling process of MMA into these particles. This approach offers a more convenient alternative to prepare polymeric spongelike material without any etching procedure.

  3. Stabilization of porcine pancreatic elastase crystals by glutaraldehyde cross-linking.

    Science.gov (United States)

    Hofbauer, Stefan; Brito, José A; Mulchande, Jalmira; Nogly, Przemyslaw; Pessanha, Miguel; Moreira, Rui; Archer, Margarida

    2015-10-01

    Elastase is a serine protease from the chymotrypsin family of enzymes with the ability to degrade elastin, an important component of connective tissues. Excessive elastin proteolysis leads to a number of pathological diseases. Porcine pancreatic elastase (PPE) is often used for drug development as a model for human leukocyte elastase (HLE), with which it shares high sequence identity. Crystals of PPE were grown overnight using sodium sulfate and sodium acetate at acidic pH. Cross-linking the crystals with glutaraldehyde was needed to resist the soaking procedure with a diethyl N-(methyl)pyridinyl-substituted oxo-β-lactam inhibitor. Crystals of PPE bound to the inhibitor belonged to the orthorhombic space group P2₁2₁2₁, with unit-cell parameters a = 51.0, b = 58.3, c = 74.9 Å, and diffracted to 1.8 Å resolution using an in-house X-ray source.

  4. Krebs cycle metabolon: structural evidence of substrate channeling revealed by cross-linking and mass spectrometry.

    Science.gov (United States)

    Wu, Fei; Minteer, Shelley

    2015-02-02

    It has been hypothesized that the high metabolic flux in the mitochondria is due to the self-assembly of enzyme supercomplexes (called metabolons) that channel substrates from one enzyme to another, but there has been no experimental confirmation of this structure or the channeling. A structural investigation of enzyme organization within the Krebs cycle metabolon was accomplished by in vivo cross-linking and mass spectrometry. Eight Krebs cycle enzyme components were isolated upon chemical fixation, and interfacial residues between mitochondrial malate dehydrogenase, citrate synthase, and aconitase were identified. Using constraint protein docking, a low-resolution structure for the three-enzyme complex was achieved, as well as the two-fold symmetric octamer. Surface analysis showed formation of electrostatic channeling upon protein-protein association, which is the first structural evidence of substrate channeling in the Krebs cycle metabolon.

  5. Stabilization of human prostate acid phosphatase by cross-linking with diimidoesters.

    Science.gov (United States)

    Wasylewska, E; Dulińska, J; Trubetskoy, V S; Torchilin, V P; Ostrowski, W S

    1987-01-01

    1. Modification of dimeric human prostate acid phosphatase (EC 3.1.3.2) by diimidoesters leads to the formation of water-soluble preparations of high enzymatic activity, resistant to denaturing agents. 2. Monomeric, dimeric, trimeric and tetrameric species were found in SDS-polyacrylamide gel electrophoresis of the phosphatase cross-linked with dimethyl-suberimidate, and dimeric, trimeric and tetrameric enzymatically active species on thin-layer Sephadex 200 gel filtration. This molecular pattern evidenced formation of the inter-subunit covalent linkages. All molecular forms are immunoreactive against the polyclonal rabbit anti-phosphatase antibodies. 3. The catalytic properties of the modified phosphatase are almost the same as those of the native enzyme. Differences in the optical properties between the modified and the native enzymes point to slight conformational transitions in the modified enzyme.

  6. Antioxidant films based on cross-linked methyl cellulose and native Chilean berry for food packaging applications.

    Science.gov (United States)

    López de Dicastillo, Carol; Rodríguez, Francisco; Guarda, Abel; Galotto, Maria José

    2016-01-20

    Development of antioxidant and antimicrobial active food packaging materials based on biodegradable polymer and natural plant extracts has numerous advantages as reduction of synthetic additives into the food, reduction of plastic waste, and food protection against microorganisms and oxidation reactions. In this way, active films based on methylcellulose (MC) and maqui (Aristotelia chilensis) berry fruit extract, as a source of antioxidants agents, were studied. On the other hand, due to the high water affinity of MC, this polymer was firstly cross-linked with glutaraldehyde (GA) at different concentrations. The results showed that the addition of GA decreased water solubility, swelling, water vapor permeability of MC films, and the release of antioxidant substances from the active materials increased with the concentration of GA. Natural extract and active cross-linked films were characterized in order to obtain the optimal formulation with the highest antioxidant activity and the best physical properties for latter active food packaging application.

  7. Cross-linking effect on dielectric properties of polypropylene thin films and applications in electric energy storage

    Science.gov (United States)

    Yuan, Xuepei; Chung, T. C. Mike

    2011-02-01

    A family of cross-linked polypropylene (x-PP) thin film dielectrics is systematically studied to understand the cross-linking effect on the dielectric properties. Evidently, the butylstyrene (BSt) cross-linkers increase both the dielectric constant (ɛ) and breakdown strength (E), without increasing energy loss. An x-PP dielectric, with 3.65 mol % BSt cross-linkers, exhibits a ɛ ˜3, which is independent of a wide range of temperatures and frequencies, slim D-E hysteresis loops, high breakdown strength (E=650 MV/m), narrow breakdown distribution, and reliable energy storage capacity >5 J/cm3 (double that of state-of-the-art biaxially oriented polypropylene capacitors), without showing any increase in energy loss.

  8. Differential Enzymatic 16O/18O Labelling for the Detection of Cross-Linked Nucleic Acid-Protein Heteroconjugates.

    Science.gov (United States)

    Flett, Fiona J; Sachsenberg, Timo; Kohlbacher, Oliver; Mackay, C Logan; Interthal, Heidrun

    2017-09-08

    Cross-linking of nucleic acids to proteins in combination with mass spectrometry permits the precise identification of interacting residues between nucleic acid-protein complexes. However, the mass spectrometric identification and characterisation of cross-linked nucleic acid-protein heteroconjugates within a complex sample is challenging. Here we establish a novel enzymatic differential 16O/18O labelling approach, which uniquely labels heteroconjugates. We have developed an automated data analysis workflow based on OpenMS for the identification of differentially isotopically labelled heteroconjugates against a complex background. We validated our method using synthetic model DNA oligonucleotide-peptide heteroconjugates which were subjected to the labelling reaction and analysed by high resolution FT-ICR mass spectrometry.

  9. Synthesis of G-N2-(CH2)3-N2-G Trimethylene DNA interstrand cross-links

    Science.gov (United States)

    Gruppi, Francesca; Salyard, Tracy L. Johnson; Rizzo, Carmelo J.

    2014-01-01

    The synthesis of G-N2-(CH2)3-N2-G trimethylene DNA interstrand cross-links (ICLs) in a 5′-CG-3′ and 5′-GC-3′ sequence from oligodeoxynucleotides containing N2-(3-aminopropyl)-2′-deoxyguanosine and 2-fluoro-O6-(trimethylsilylethyl)inosine is presented. Automated solid-phase DNA synthesis was used for unmodified bases and modified nucleotides were incorporated via their corresponding phosphoramidite reagent by a manual coupling protocol. The preparation of the phosphoramidite reagents for incorporation of N2-(3-aminopropyl)-2′-deoxyguanosine is reported. The high-purity trimethylene DNA interstrand cross-link product is obtained through a nucleophilic aromatic substitution reaction between the N2-(3-aminopropyl)-2′-deoxyguanosine and 2-fluoro-O6-(trimethylsilylethyl)inosine containing oligodeoxynucleotides. PMID:25431636

  10. Cytocompatible in situ cross-linking of degradable LbL films based on thiol-exchange reaction.

    Science.gov (United States)

    Yang, Sung Ho; Choi, Jinsu; Palanikumar, L; Choi, Eun Seong; Lee, Juno; Kim, Juan; Choi, Insung S; Ryu, Ja-Hyoung

    2015-08-01

    Formation of both mechanically durable and programmably degradable layer-by-layer (LbL) films in a biocompatible fashion has potential applications in cell therapy, tissue engineering, and drug-delivery systems, where the films are interfaced with living cells. In this work, we developed a simple but versatile method for generating in situ cross-linked and responsively degradable LbL films, based on the thiol-exchange reaction, under highly cytocompatible conditions (aqueous solution at pH 7.4 and room temperature). The cytocompatibility of the processes was confirmed by coating individual yeast cells with the cross-linked LbL films and breaking the films on demand, while maintaining the cell viability. In addition, the processes were applied to the controlled release of an anticancer drug in the HeLa cells.

  11. Corneal changes following collagen cross linking and simultaneous topography guided photoablation with collagen cross linking for keratoconus

    Directory of Open Access Journals (Sweden)

    Prema Padmanabhan

    2014-01-01

    Full Text Available Purpose: To compare the outcome of Collagen cross-linking (CXL with that following topography-guided customized ablation treatment (T-CAT with simultaneous CXL in eyes with progressive keratoconus. Materials and Methods: This was a prospective, non-randomized single centre study of 66 eyes with progressive keratoconus. Of these, 40 eyes underwent CXL and 26 eyes underwent T-CAT + CXL. The refractive, topographic, tomographic and aberrometric changes measured at baseline, 1, 3 and 6 months post-operatively were compared between both groups. Results: After a mean follow-up of 7.7 ± 1.3 months, the mean retinoscopic cylinder decreased by 1.02 ± 3.16 D in the CXL group ( P = 0.1 and 2.87 ± 3.22 D in the T-CAT + CXL group ( P = 0.04. The Best corrected visual acuity increased by 2 lines or more in 10% of eyes in the CXL group and in 23.3% of eyes in the T-CAT + CXL group. The mean steepest-K reduced by 0.40 ± 3.71 D ( P = 0.77 in the CXL group and by 2.91 ± 2.01D ( P = 0.03 in the T-CAT + CXL group. The sag factor and surface asymmetry index showed no significant change in the CXL group but reduced by 3.59 ± 5.94 D ( P = 0.01 and 0.72 ± 1.18 ( P = 0.02 respectively in the T-CAT + CXL group. There was a significant increase in the highest posterior corneal elevation in both groups (9.57 ± 14.93 μ in the CXL group and 7.85 ± 9.25 μ in the T-CAT + CXL group, P ≤ 0.001 for both. There was significantly greater reduction of mean coma ( P < 0.001 and mean higher-order aberrations ( P = 0.01 following T-CAT + CXL compared to CXL. Conclusions: CAT + CXL is an effective approach to confer biomechanical stability and to improve the corneal contour in eyes with keratoconus and results in better refractive, topographic and aberrometric outcomes than CXL alone.

  12. Integrated Workflow for Structural Proteomics Studies Based on Cross-Linking/Mass Spectrometry with an MS/MS Cleavable Cross-Linker.

    Science.gov (United States)

    Arlt, Christian; Götze, Michael; Ihling, Christian H; Hage, Christoph; Schäfer, Mathias; Sinz, Andrea

    2016-08-16

    Cross-linking combined with mass spectrometry (MS) has evolved as an alternative strategy in structural biology for characterizing three-dimensional structures of protein assemblies and for mapping protein-protein interactions. Here, we describe an integrated workflow for an automated identification of cross-linked products that is based on the use of a tandem mass spectrometry (MS/MS) cleavable cross-linker (containing a 1,3-bis-(4-oxo-butyl)-urea group, BuUrBu) generating characteristic doublet patterns upon fragmentation. We evaluate different fragmentation methods available on an Orbitrap Fusion mass spectrometer for three proteins and an E. coli cell lysate. An updated version of the dedicated software tool MeroX was employed for a fully automated identification of cross-links. The strength of our cleavable cross-linker is that characteristic patterns of the cross-linker as well as backbone fragments of the connected peptides are already observed at the MS/MS level, eliminating the need for conducting MS(3) or sequential CID (collision-induced dissociation)- and ETD (electron transfer dissociation)-MS/MS experiments. This makes our strategy applicable to a broad range of mass spectrometers with MS/MS capabilities. For purified proteins and protein complexes, our workflow using CID-MS/MS acquisition performs with high confidence, scoring cross-links at 0.5% false discovery rate (FDR). The cross-links provide structural insights into the intrinsically disordered tetrameric tumor suppressor protein p53. As a time-consuming manual inspection of cross-linking data is not required, our workflow will pave the way for making the cross-linking/MS approach a routine technique for structural proteomics studies.

  13. Incorporation of pentraxin 3 into hyaluronan matrices is tightly regulated and promotes matrix cross-linking.

    Science.gov (United States)

    Baranova, Natalia S; Inforzato, Antonio; Briggs, David C; Tilakaratna, Viranga; Enghild, Jan J; Thakar, Dhruv; Milner, Caroline M; Day, Anthony J; Richter, Ralf P

    2014-10-31

    Mammalian oocytes are surrounded by a highly hydrated hyaluronan (HA)-rich extracellular matrix with embedded cumulus cells, forming the cumulus cell·oocyte complex (COC) matrix. The correct assembly, stability, and mechanical properties of this matrix, which are crucial for successful ovulation, transport of the COC to the oviduct, and its fertilization, depend on the interaction between HA and specific HA-organizing proteins. Although the proteins inter-α-inhibitor (IαI), pentraxin 3 (PTX3), and TNF-stimulated gene-6 (TSG-6) have been identified as being critical for COC matrix formation, its supramolecular organization and the molecular mechanism of COC matrix stabilization remain unknown. Here we used films of end-grafted HA as a model system to investigate the molecular interactions involved in the formation and stabilization of HA matrices containing TSG-6, IαI, and PTX3. We found that PTX3 binds neither to HA alone nor to HA films containing TSG-6. This long pentraxin also failed to bind to products of the interaction between IαI, TSG-6, and HA, among which are the covalent heavy chain (HC)·HA and HC·TSG-6 complexes, despite the fact that both IαI and TSG-6 are ligands of PTX3. Interestingly, prior encounter with IαI was required for effective incorporation of PTX3 into TSG-6-loaded HA films. Moreover, we demonstrated that this ternary protein mixture made of IαI, PTX3, and TSG-6 is sufficient to promote formation of a stable (i.e. cross-linked) yet highly hydrated HA matrix. We propose that this mechanism is essential for correct assembly of the COC matrix and may also have general implications in other inflammatory processes that are associated with HA cross-linking. © 2014 by The American Society for Biochemistry and Molecular Biology, Inc.

  14. High Density Metamaterials for Visible Light

    Science.gov (United States)

    2016-11-28

    Split Ring Resonator Metamaterials with Fundamental Magnetic Resonance in the Middle Visible Spectrum,” Adv. Opt. Mater., vol. 2, no. 3, pp. 280–285...AFRL-AFOSR-JP-TR-2016-0097 High density metamaterials for visible light Dao Hua Zhang NANYANG TECHNOLOGICAL UNIVERSITY Final Report 11/28/2016...COVERED (From - To)  16 Jul 2014 to 15 Jul 2016 4. TITLE AND SUBTITLE High density metamaterials for visible light 5a.  CONTRACT NUMBER 5b.  GRANT

  15. A quarksonic matter at high isospin density

    CERN Document Server

    Cao, Gaoqing; Huang, Xu-Guang

    2016-01-01

    Analogous to the quarkyonic matter at high baryon density in which the quark Fermi seas and the baryonic excitations coexist, it is argued that a "quarksonic matter" phase appears at high isospin density where the quark (antiquark) Fermi seas and the mesonic excitations coexist. We explore this phase in detail in both large $N_c$ and asymptotically free limits: In large $N_c$ limit, we sketch a phase diagram for the quarksonic matter. In the asymptotically free limit, we study the pion superfluidity and thermodynamics of the quarksonic matter by using both perturbative calculations and effective model.

  16. Polysiloxane Functionalized Carbon Dots and Their Cross-Linked Flexible Silicone Rubbers for Color Conversion and Encapsulation of White LEDs.

    Science.gov (United States)

    Wang, Yunfeng; Yin, Zhengmao; Xie, Zheng; Zhao, Xinxin; Zhou, Chuanjian; Zhou, Shuyun; Chen, Ping

    2016-04-20

    In this work, aminopropylmethylpolysiloxane (AMS) functionalized luminescent carbon dots (AMS-CDs) were prepared via a one-step solvothermal method. AMS-CDs could be self- or co-cross-linking with AMS to form 3D flexible transparent silicone rubbers (SRs) where CDs acted as cross-linking points, so the loading fraction of AMS-CDs could be adjusted from 10 to 100 wt %, thus modulating fluorescence properties and flexibility of silicone rubbers. Because of the self-curing property and high thermal stability, AMS-CDs were also studied in white LEDs (WLEDs), serving as a color conversion and encapsulation layer of GaN based blue LEDs simultaneously that would avoid the traditional problem of poor compatibility between emitting and packaging materials. And the color coordinate of AMS-CDs based WLEDs (0.33, 0.28) was very close to the pure white light. In addition, the obtained CDs cross-linked SRs had good transparency (T > 80%) at 510-1400 nm and high refractive indexes (1.33-1.54) that could meet the need of commercial packaging materials and optical application. AMS-CDs were also promising to be used in the UV LEDs based WLEDs according to their wide wavelength emission and flexible optoelectronic device.

  17. Exceptionally stable polymer electrolyte for a lithium battery based on cross-linking by a residue-free process

    Science.gov (United States)

    Daigle, Jean-Christophe; Asakawa, Yuichiro; Vijh, Ashok; Hovington, Pierre; Armand, Michel; Zaghib, Karim

    2016-11-01

    In this paper, we report the synthesis of cross-linked copolymers of glycidyl methacrylate (GMA) and poly (ethylene glycol) methyl methacrylate (PEGMA) for use as solid polymer electrolytes (SPE). The cross-linking is performed with volatile ethylene diamine, thus preventing the accumulation of undesirable precursors in the final membrane. The structure of the cross-linked polymer electrolyte was investigated by 13C solid NMR and its physical properties were examined by DSC, TGA and stress-strain tests. The ionic conductivities were determined by AC Impedance, which showed that the SPEs have good conductivities (10-5 Scm-1) at 80 °C. The highest capacity measured with these polymers was 151 mAh g-1 at C/6 and 80 °C for a LFP/SPE/Lithium battery. The retention capacity is high, at 97% after 80 cycles at different rates of cycling. The Young's modulus of the membranes is as high as 1 GPa. The SEM images showed no evidence of lithium dendrites and no degradation after cycling. Therefore, the polymer is a good candidate for battery operation over a long time. Especially important is the ability of this polymer to prevent growth of dendrites on the Li-metal electrode.

  18. Single- and double-ion type cross-linked polysiloxane solid electrolytes for lithium cells

    Science.gov (United States)

    Tsutsumi, Hiromori; Yamamoto, Masahiro; Morita, Masayuki; Matsuda, Yoshiharu; Nakamura, Takashi; Asai, Hiroyuki

    Polymeric solid electrolytes, that have poly(dimethylsiloxane) (PMS) backbone and cross-linked network, were applied to a rechargeable lithium battery system. Single- (PMS-Li) and double-ion type (PMS-LiClO 4) electrolytes were prepared from the same prepolymers. Lithium electrode in the both electrolytes showed reversible stripping and deposition of lithium. Intercalation and deintercalation processes of lithium ion between lithium-manganese composite oxide (Li xMnO 2) electrode and the electrolytes were also confirmed by cyclic voltammetry, however, peak current decreased with several cycles in both cases. The model cell, Li/PMS-Li/Li xMnO 2 cell had 1.4 mA h g -1 (per 1 g of active material, current density: 3.77 μA cm -2), and the Li/PMS-LiClO 4/Li xMnO 2 cell had 1.6 mA h g -1 (current density: 75.3 μA cm -2).

  19. Single- and double-ion type cross-linked polysiloxane solid electrolytes for lithium cells

    Energy Technology Data Exchange (ETDEWEB)

    Tsutsumi, Hiromori; Yamamoto, Masahiro; Morita, Masayuki; Matsuda, Yoshiharu (Dept. of Applied Chemistry and Chemical Engineering, Faculty of Engineering, Yamaguchi Univ., Ube (Japan)); Nakamura, Takashi; Asai, Hiroyuki (Dow Corning Toray Silicone Co. Ltd., Ichihara (Japan))

    1993-01-19

    Polymeric solid electrolytes, that have poly(dimethylsiloxane) (PMS) backbone and cross-linked network, were applied to a rechargeable lithium battery system. Single- (PMS-Li) and double-ion type (PMS-LiClO[sub 4]) electrolytes were prepared from the same prepolymers. Lithium electrode in the both electrolytes showed reversible stripping and deposition of lithium. Intercalation and deintercalation processes of lithium ion between lithium-manganese composite oxide (Li[sub x]MnO[sub 2]) electrode and the electrolytes were also confirmed by cyclic voltammetry, however, peak current decreased with several cycles in both cases. The model cell, Li/PMS-Li/Li[sub x]MnO[sub 2] cell had 1.4 mA h g[sup -1] (per 1 g of active material, current density: 3.77 [mu]A cm[sup -2]), and the Li/PMS-LiClO[sub 4]/Li[sub x]MnO[sub 2] cell had 1.6 mA h g[sup -1] (current density: 75.3 [mu]A cm[sup -2]). (orig.).

  20. Tailoring Elastic Properties of Silica Aerogels Cross-Linked with Polystyrene

    Science.gov (United States)

    Nguyen, Baochau N.; Meador, Mary Ann B.; Tousley, Marissa E.; Shonkwiler, Brian; McCorkle, Linda; Scheiman, Daniel A.; Palczer, Anna

    2009-01-01

    The effect of incorporating an organic linking group, 1,6-bis(trimethoxysilyl)hexane (BTMSH), into the underlying silica structure of a styrene cross-linked silica aerogel is examined. Vinyltrimethoxysilane (VTMS) is used to provide a reactive site on the silica backbone for styrene polymerization. Replacement of up to 88 mol 1 of the silicon from tetramethoxyorthosilicate with silicon derived from BTMSH and VTMS during the making of silica gels improves the elastic behavior in some formulations of the crosslinked aerogels, as evidenced by measurement of the recovered length after compression of samples to 251 strain. This is especially true for some higher density formulations, which recover nearly 100% of their length after compression to 251 strain twice. The compressive modulus of the more elastic monoliths ranged from 0.2 to 3 MPa. Although some of these monoliths had greatly reduced surface areas, changing the solvent used to produce the gels from methanol to ethanol increased the surface area in one instance from 6 to 220 sq m2/g with little affect on the modulus, elastic recovery, porosity, or density.

  1. Chemistry and physical properties of melt-processed and solution-cross-linked corn zein.

    Science.gov (United States)

    Sessa, David J; Mohamed, Abdellatif; Byars, Jeffrey A

    2008-08-27

    Corn zein was cross-linked with glutaraldehyde (GDA) using glacial acetic acid (HAc) as catalyst. The objectives are to evaluate the swelling characteristics of GDA cross-linked zein gels in water, ethanol, and their combinations. Similar formulations, upon solvent evaporation, form films. The mechanical properties of the films are compared to compression molded tensile bars from GDA melt-processed zein as a second objective. Chemistry of the cross-linking reaction was based on the aldehyde binding characteristics defined by use of fluorescence spectroscopy; sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE) to demonstrate the cross-linking reaction; FTIR to observe absorption differences of the cross-linked product; differential scanning calorimetry, dynamic mechanical analysis and thermogravimetric analysis to assess thermal properties; and the use of Instron Universal Testing Machine to evaluate mechanical properties. A reaction mechanism for acid catalyzed GDA cross-linking of zein is proposed. Thermal and mechanical properties of tensile bars cut from either film or formed by compression molding were similar, where both showed increased tensile strengths, ductility and stiffness when compared with unmodified controls. Samples that were reacted with 8% GDA by weight based on weight of zein from either process retained their integrity when tensile bars from each were subjected to boiling water for 10 min or soaking in either water or HAc for 24 h. The melt-processed, cross-linked zein is a more environmentally friendly method that would eliminate the need for HAc recovery.

  2. Modified gum arabic cross-linked gelatin scaffold for biomedical applications

    Energy Technology Data Exchange (ETDEWEB)

    Sarika, P.R. [Department of Chemistry, Indian Institute of Space Science and Technology, Valiamala, Thiruvananthapuram, Kerala 695 547 (India); Cinthya, Kuriakose [Tissue Culture Laboratory, Biomedical Technology Wing, Sree Chitra Tirunal Institute for Medical Sciences and Technology, Poojappura, Thiruvananthapuram, Kerala 695 012 (India); Jayakrishnan, A. [Department of Biotechnology, Indian Institute of Technology Madras, Chennai 600 036 (India); Anilkumar, P.R., E-mail: anilkumarpr@sctimst.ac.in [Tissue Culture Laboratory, Biomedical Technology Wing, Sree Chitra Tirunal Institute for Medical Sciences and Technology, Poojappura, Thiruvananthapuram, Kerala 695 012 (India); James, Nirmala Rachel, E-mail: nirmala@iist.ac.in [Department of Chemistry, Indian Institute of Space Science and Technology, Valiamala, Thiruvananthapuram, Kerala 695 547 (India)

    2014-10-01

    The present work deals with development of modified gum arabic cross-linked gelatin scaffold for cell culture. A new biocompatible scaffold was developed by cross-linking gelatin (Gel) with gum arabic, a polysaccharide. Gum arabic was subjected to periodate oxidation to obtain gum arabic aldehyde (GAA). GAA was reacted with gelatin under appropriate pH to prepare the cross-linked hydrogel. Cross-linking occurred due to Schiff's base reaction between aldehyde groups of oxidized gum arabic and amino groups of gelatin. The scaffold prepared from the hydrogel was characterized by swelling properties, degree of cross-linking, in vitro degradation and scanning electron microscopy (SEM). Cytocompatibility evaluation using L-929 and HepG2 cells confirmed non-cytotoxic and non-adherent nature of the scaffold. These properties are essential for generating multicellular spheroids and hence the scaffold is proposed to be a suitable candidate for spheroid cell culture. - Highlights: • Gum arabic cross-linked gelatin scaffold was developed for tissue engineering. • Cross-linking was achieved by Schiff's base reaction. • The scaffold is non-cytotoxic and non adherent to fibroblast and hepatocytes. • The scaffolds are potential candidates for spheroid cell culture.

  3. Understanding chemical reactivity for homo- and heterobifunctional protein cross-linking agents.

    Science.gov (United States)

    Chen, Fan; Nielsen, Simone; Zenobi, Renato

    2013-07-01

    Chemical cross-linking, combined with mass spectrometry, has been applied to map three-dimensional protein structures and protein-protein interactions. Proper choice of the cross-linking agent, including its reactive groups and spacer arm length, is of great importance. However, studies to understand the details of reactivity of the chemical cross-linkers with proteins are quite sparse. In this study, we investigated chemical cross-linking from the aspects of the protein structures and the cross-linking reagents involved, by using two structurally well-known proteins, glyceraldehyde 3-phosohate dehydrogenase and ribonuclease S. Chemical cross-linking reactivity was compared using a series of homo- and hetero-bifunctional cross-linkers, including bis(sulfosuccinimidyl) suberate, dissuccinimidyl suberate, bis(succinimidyl) penta (ethylene glycol), bis(succinimidyl) nona (ethylene glycol), m-maleimidobenzoyl-N-hydroxysulfosuccinimide ester, 2-pyridyldithiol-tetraoxaoctatriacontane-N-hydrosuccinimide and succinimidyl-[(N-maleimidopropionamido)-tetracosaethyleneglycol]ester. The protein structure itself, especially the distances between target amino acid residues, was found to be a determining factor for the cross-linking efficiency. Moreover, the reactive groups of the chemical cross-linker also play an important role; a higher cross-linking reaction efficiency was found for maleimides compared to 2-pyrimidyldithiols. The reaction between maleimides and sulfhydryl groups is more favorable than that between N-hydroxysuccinimide esters and amine groups, although cysteine residues are less abundant in proteins compared to lysine residues. Copyright © 2013 John Wiley & Sons, Ltd.

  4. Shell and core cross-linked poly(L-lysine)/poly(acrylic acid) complex micelles.

    Science.gov (United States)

    Hsieh, Yi-Hsuan; Hsiao, Yung-Tse; Jan, Jeng-Shiung

    2014-12-21

    We report the versatility of polyion complex (PIC) micelles for the preparation of shell and core cross-linked (SCL and CCL) micelles with their surface properties determined by the constituent polymer composition and cross-linking agent. The negatively and positively charged PIC micelles with their molecular structure and properties depending on the mixing weight percentage and polymer molecular weight were first prepared by mixing the negatively and positively charged polyions, poly(acrylic acid) (PAA) and poly(L-lysine) (PLL). The feasibility of preparing SCL micelles was demonstrated by cross-linking the shell of the negatively and positively charged micelles using cystamine and genipin, respectively. The core of the micelles can be cross-linked by silica deposition to stabilize the assemblies. The shell and/or core cross-linked micelles exhibited excellent colloid stability upon changing solution pH. The drug release from the drug-loaded SCL micelles revealed that the controllable permeability of the SCL micelles can be achieved by tuning the cross-linking degree and the SCL micelles exhibited noticeable pH-responsive behavior with accelerated release under acidic conditions. With the versatility of cross-linking strategies, it is possible to prepare a variety of SCL and CCL micelles from PIC micelles.

  5. Preparation and Characterization of Ionotropic Cross-Linked Chitosan Microparticles for Controlled Release of Aceclofenac

    Directory of Open Access Journals (Sweden)

    N. G. Raghavendra Rao

    2010-04-01

    Full Text Available Aceclofenac, (2-[2-[2-(2, 6-dichlorophenyl aminophenyl] acety] oxyacetic acid a non-steroidal anti-inflammatory drug (NSAID, has been indicated for various conditions like post-traumatic pain, rheumatoid arthritis, ankylosing spondylitis. Multiple-unit systems have been reported to avoid the variations in gastric emptying and different transit rates through gastro-intestinal and spread over a large area preventing exposure of the absorbing site to high drug concentration on chronic dosing. The purpose of this study was therefore to develop aceclofenac loaded chitosan microparticles by ionotropic gelation method. Drug loading efficiency (DLE of microparticles was found between 62.20 to 92.93 % and depended on the formulation variables. Increase in the Tripolyphosphate (TPP concentration, pH of the TPP solution and cross-linking time decreased the drug release. The particle size decreased with increase in cross-linking time and found between the ranges of 1194.1 to 1568.9 µm. Drug release showed slight burst effect in phosphate buffer pH 7.4 in first hour followed by prolonged release for 8 hrs. FTIR and DSC revealed that there was no interaction between drug and polymer. The release data was fitted into first order, zero order and Higuchi model to find release kinetics. The values of regression coefficient r2 were found to be greater (£ 0.9541 for first order than for zero order (£ 0.8740 and the r2 value for Higuchi was £ 0.9805 suggesting diffusion controlled process. The result concluded that TPP-chitosan microparticles developed by ionotropic gelation method might become potential delivery system to prolonging the release of aceclofenac.

  6. Pickering emulsions stabilized by whey protein nanoparticles prepared by thermal cross-linking.

    Science.gov (United States)

    Wu, Jiande; Shi, Mengxuan; Li, Wei; Zhao, Luhai; Wang, Ze; Yan, Xinzhong; Norde, Willem; Li, Yuan

    2015-03-01

    A Pickering (o/w) emulsion was formed and stabilized by whey protein isolate nanoparticles (WPI NPs). Those WPI NPs were prepared by thermal cross-linking of denatured WPI proteins within w/o emulsion droplets at 80°C for 15 min. During heating of w/o emulsions containing 10% (w/v) WPI proteins in the water phase, the emulsions displayed turbid-transparent-turbid phase transitions, which is ascribed to the change in the size of the protein-containing water droplets caused by thermal cross-linking between denatured protein molecules. The transparent stage indicated the formation of WPI NPs. WPI NPs of different sizes were obtained by varying the mixing speed. WPI NPs of 200-500 nm were selected to prepare o/w Pickering emulsions because of their good stability against coalescence. By Confocal Laser Scanning Microscopy, it was observed that WPI NPs were closely packed and distributed at the surface of the emulsion droplets. By measuring water contact angles of WPI NPs films, it was found that under most conditions WPI NPs present good partial wetting properties, but that at the isoelectric point (pI) and high ionic strength the particles become more hydrophobic, resulting in less stable Pickering emulsion. Thus, at pH above and below the pI of WPI NPs and low to moderate ionic strengths (1-10 mM), and with a WPI NPs concentration of 2% (w/v), a stable Pickering emulsion can be obtained. The results may provide useful information for applications of WPI NPs in environmentally friendly and food grade applications, notably in food, pharmaceutical and cosmetic products.

  7. High energy density in multisoliton collisions

    Science.gov (United States)

    Saadatmand, Danial; Dmitriev, Sergey V.; Kevrekidis, Panayotis G.

    2015-09-01

    Solitons are very effective in transporting energy over great distances and collisions between them can produce high energy density spots of relevance to phase transformations, energy localization and defect formation among others. It is then important to study how energy density accumulation scales in multisoliton collisions. In this study, we demonstrate that the maximal energy density that can be achieved in collision of N slowly moving kinks and antikinks in the integrable sine-Gordon field, remarkably, is proportional to N2, while the total energy of the system is proportional to N . This maximal energy density can be achieved only if the difference between the number of colliding kinks and antikinks is minimal, i.e., is equal to 0 for even N and 1 for odd N and if the pattern involves an alternating array of kinks and antikinks. Interestingly, for odd (even) N the maximal energy density appears in the form of potential (kinetic) energy, while kinetic (potential) energy is equal to zero. The results of the present study rely on the analysis of the exact multisoliton solutions for N =1 ,2 , and 3 and on the numerical simulation results for N =4 ,5 ,6 , and 7. The effect of weak Hamiltonian and non-Hamiltonian perturbations on the maximal energy density in multikink collisions is also discussed as well as that of the collision relative phase. Based on these results one can speculate that the soliton collisions in the sine-Gordon field can, in principle, controllably produce very high energy density. This can have important consequences for many physical phenomena described by the Klein-Gordon equations.

  8. Bifunctional alkylating agent-mediated MGMT-DNA cross-linking and its proteolytic cleavage in 16HBE cells.

    Science.gov (United States)

    Cheng, Jin; Ye, Feng; Dan, Guorong; Zhao, Yuanpeng; Wang, Bin; Zhao, Jiqing; Sai, Yan; Zou, Zhongmin

    2016-08-15

    Nitrogen mustard (NM), a bifunctional alkylating agent (BAA), contains two alkyl arms and can act as a cross-linking bridge between DNA and protein to form a DNA-protein cross-link (DPC). O(6)-methylguanine-DNA methyltransferase (MGMT), a DNA repair enzyme for alkyl adducts removal, is found to enhance cell sensitivity to BAAs and to promote damage, possibly due to its stable covalent cross-linking with DNA mediated by BAAs. To investigate MGMT-DNA cross-link (mDPC) formation and its possible dual roles in NM exposure, human bronchial epithelial cell line 16HBE was subjected to different concentrations of HN2, a kind of NM, and we found mDPC was induced by HN2 in a concentration-dependent manner, but the mRNA and total protein of MGMT were suppressed. As early as 1h after HN2 treatment, high mDPC was achieved and the level maintained for up to 24h. Quick total DPC (tDPC) and γ-H2AX accumulation were observed. To evaluate the effect of newly predicted protease DVC1 on DPC cleavage, we applied siRNA of MGMT and DVC1, MG132 (proteasome inhibitor), and NMS-873 (p97 inhibitor) and found that proteolysis plays a role. DVC1 was proven to be more important in the cleavage of mDPC than tDPC in a p97-dependent manner. HN2 exposure induced DVC1 upregulation, which was at least partially contributed to MGMT cleavage by proteolysis because HN2-induced mDPC level and DNA damage was closely related with DVC1 expression. Homologous recombination (HR) was also activated. Our findings demonstrated that MGMT might turn into a DNA damage promoter by forming DPC when exposed to HN2. Proteolysis, especially DVC1, plays a crucial role in mDPC repair.

  9. Aluminum-induced dreierketten chain cross-links increase the mechanical properties of nanocrystalline calcium aluminosilicate hydrate

    Science.gov (United States)

    Geng, Guoqing; Myers, Rupert J.; Li, Jiaqi; Maboudian, Roya; Carraro, Carlo; Shapiro, David A.; Monteiro, Paulo J. M.

    2017-01-01

    The incorporation of Al and increased curing temperature promotes the crystallization and cross-linking of calcium (alumino)silicate hydrate (C-(A-)S-H), which is the primary binding phase in most contemporary concrete materials. However, the influence of Al-induced structural changes on the mechanical properties at atomistic scale is not well understood. Herein, synchrotron radiation-based high-pressure X-ray diffraction is used to quantify the influence of dreierketten chain cross-linking on the anisotropic mechanical behavior of C-(A-)S-H. We show that the ab-planar stiffness is independent of dreierketten chain defects, e.g. vacancies in bridging tetrahedra sites and Al for Si substitution. The c-axis of non-cross-linked C-(A-)S-H is more deformable due to the softer interlayer opening but stiffens with decreased spacing and/or increased zeolitic water and Ca2+ of the interlayer. Dreierketten chain cross-links act as ‘columns’ to resist compression, thus increasing the bulk modulus of C-(A-)S-H. We provide the first experimental evidence on the influence of the Al-induced atomistic configurational change on the mechanical properties of C-(A-)S-H. Our work advances the fundamental knowledge of C-(A-)S-H on the lowest level of its hierarchical structure, and thus can impact the way that innovative C-(A-)S-H-based cementitious materials are developed using a ‘bottom-up’ approach. PMID:28281635

  10. Supernovae and high density nuclear matter

    Energy Technology Data Exchange (ETDEWEB)

    Kahana, S.

    1986-01-01

    The role of the nuclear equation of state (EOS) in producing prompt supernova explosions is examined. Results of calculations of Baron, Cooperstein, and Kahana incorporating general relativity and a new high density EOS are presented, and the relevance of these calculations to laboratory experiments with heavy ions considered. 31 refs., 6 figs., 2 tabs.

  11. High Gluon Densities in Heavy Ions Collisions

    CERN Document Server

    Blaizot, Jean-Paul

    2016-01-01

    The early stages of heavy ion collisions are dominated by high density systems of gluons that carry each a small fraction $x$ of the momenta of the colliding nucleons. A distinguishing feature of such systems is the phenomenon of "saturation" which tames the expected growth of the gluon density as the energy of the collision increases. The onset of saturation occurs at a particular transverse momentum scale, the "saturation momentum", that emerges dynamically and that marks the onset of non-linear gluon interactions. At high energy, and for large nuclei, the saturation momentum is large compared to the typical hadronic scale, making high density gluons amenable to a description with weak coupling techniques. This paper reviews some of the challenges faced in the study of such dense systems of small $x$ gluons, and of the progress made in addressing them. The focus is on conceptual issues, and the presentation is both pedagogical, and critical. Examples where high gluon density could play a visible role in hea...

  12. High Density GEOSAT/GM Altimeter Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The high density Geosat/GM altimeter data south of 30 S have finally arrived. In addition, ERS-1 has completed more than 6 cycles of its 35-day repeat track. These...

  13. Structural and spectral characteristics of the cross-linked dimer derived from electrooxidation of cyclic 1,N2-propanoguanosine.

    Science.gov (United States)

    Murakami, Hiroya; Esaka, Yukihiro; Uno, Bunji

    2011-01-01

    The acetaldehyde-derived cyclic propano adduct of 2'-deoxyguanosine was easily oxidized electrochemically into the cross-linked dimer as an oxidative product. The structural and spectroscopic characteristics of the dimer were investigated by MS, (1)H and (13)C-NMR, UV, and DFT calculations. The dimer formation was inferred from a molecular ionic peak of m/z 705 ([(2M-2H)+H](+), M being the molecular weight of the monomer) on the ESI-MS spectra and the chemical formula as C(28)H(36)N(10)O(12) provided by the high-resolution ESI-MS results. The C2-N5 linkage between the two monomers in the dimer was deduced from the (1)H- and (13)C-NMR spectral results. In addition, the correlations in the 2-dimensional NMR spectra (DQF-COSY and HMBC) were consistently explained by the structure of the C2-N5 cross-linked dimer. UV spectral measurements also support the C2-N5 linking in the dimer formation. The formation of the cross-link dimer as an oxidative lesion of the acetaldehyde-derived cyclic propano adduct of guanosine is expected to interfere with DNA replication and to contribute to acetaldehyde-mediated genotoxicity.

  14. Adsorptive removal of lead and cadmium ions using Cross -linked CMC Schiff base: Isotherm, Kinetics and Catalytic Activity

    Directory of Open Access Journals (Sweden)

    P. Moganavally

    2016-03-01

    Full Text Available Water plays a vital role to human and other living organisms. Due to the effluent coming from chemical industries, the industrial activity, contamination of ground water level is goes on increasing nowadays. Therefore, there is a need to develop technologies that can remove toxic pollutants in wastewater. Hence the cross linked Carboxymethyl chitosan(CMC/ 2,3-dimethoxy Benzaldehyde Schiff base complex has been synthesized and characterized by using FT-IR and SEM analysis. All these results revealed that cross linked Schiff base has formed with high adsorption capacity. The prepared effective adsorbent used for the removal of heavy metals like lead (II and cadmium (II ions from aqueous solution and the adsorption data follow the Freundlich model, which follows pseudo first order kinetics. Effect of various parameters like solution pH, adsorbent dose and contact time for the removal of heavy metals has been studied. The synthesized sample undergoes catalytic oxidation process significantly at 24 hrs. The results showed that cross linked Schiff base is an effective, eco-friendly, low-cost adsorbent.

  15. A novel method for immobilization of proteins via entrapment of magnetic nanoparticles through epoxy cross-linking.

    Science.gov (United States)

    Iype, Tessy; Thomas, Jaiby; Mohan, Sangeetha; Johnson, Kochurani K; George, Ligi E; Ambattu, Lizebona A; Bhati, Aniruddha; Ailsworth, Kristen; Menon, Bindu; Rayabandla, Sunayana M; Jesudasan, Rachel A; Santhosh, Sam; Ramchand, Chaniyilparampu N

    2017-02-15

    A method for immobilization of functional proteins by chemical cross-linking of the protein of interest and uncoated iron oxide nanoparticles in the presence of Epichlorohydrin is described. As a result of the cross-linking, the proteins form a matrix in which the particles get entrapped. The optimum concentration of Epichlorohydrin that facilitates immobilization of protein without affecting the functional properties of the protein was determined. This method was used to immobilize several functional proteins and the development and functional activity of Protein A-magnetic nanoparticles (MNPs) is described here in detail. The Protein A-MNPs possess high binding capacity due to the increased surface area of uncoated nanoparticles and robust magnetic separation due to the absence of polymeric coating materials. Protein A-MNPs were successfully used for purification of antibodies and also for immunoprecipitation. We also immobilized enzymes such as horse radish peroxidase and esterase and found that by providing the optimum incubation time, temperature and protein to nanoparticle ratio, we can retain the activity and improve the stability of the enzyme. This study is the first demonstration that Epichlorohydrin can be used to entrap nanoparticles in a cross-linked matrix of protein without impairing the activity of immobilized protein.

  16. Grafted, cross-linked carbon black as a double-layer capacitor electrode material

    Energy Technology Data Exchange (ETDEWEB)

    Richner, R.; Mueller, S.; Wokaun, A.

    2001-03-01

    Isocyanate prepolymers readily react with oxidic functional groups on carbon black. On carbon black grafted with diisocyanates, reactive isocyanate groups are available for cross-linking to a polyurethane system. This cross-linked carbon black was considered as a new active material for electrochemical electrodes. Active material for electric double-layer capacitor electrodes was produced which had values of specific capacitance of up to 200 F/g. Cross-linking efficiencies of up to 58 % of the polymers utilised were achieved. (author)

  17. Characterization of solid UV cross-linked PEGDA for biological applications

    KAUST Repository

    Castro, David

    2013-10-20

    This paper reports on solid UV cross-linked Poly(ethylene)-glycol-diacrylate (PEGDA) as a material for microfluidic devices for biological applications. We have evaluated biocompatibility of PEGDA through two separate means: 1) by examining cell viability and attachment on cross-linked PEGDA surfaces for cell culture applications, and 2) by determining if cross-linked PEGDA inhibits the polymerase chain reaction (PCR) processes for on-chip PCR. Through these studies a correlation has been found between degree of curing and cell viability, attachment, as well as on PCR outcome.

  18. A genetic anomaly of oriented collagen biosynthesis and cross-linking: Keratoconus.

    Science.gov (United States)

    Bourges, J L; Robert, A M; Robert, L

    2015-02-01

    Oriented collagen biosynthesis is one of the major mechanisms involved in tissue and organ formation during development. Corneal biogenesis is one example. Defects in this process lead to anomalies in tissue structure and function. The transparency of cornea and its achievement are a good example as well as its pathological modifications. Keratoconus is one example of this type of pathologies, involving also inappropriate cross-linking of collagen fibers. Among the tentatives to correct this anomaly, the riboflavin-potentiated UV-cross-linking (CXL) of keratoconus corneas appears clinically satisfactory, although none of the experiments and clinical results published prove effective cross-linking. The published results are reviewed in this article.

  19. 甲醛交联法研究高温条件下大肠杆菌体内小分子热休克蛋白IbpB的客户蛋白%Research on the client proteins of small heat shock protein IbpB in Escherichia coli cells under a high temperature by formaldehyde cross-linking

    Institute of Scientific and Technical Information of China (English)

    石小东; 胡蕊; 胡秋梅

    2015-01-01

    目的:研究高温条件下小分子热休克蛋白IbpB在大肠杆菌体内的客户蛋白以及在此温度下IbpB对其客户蛋白的作用。方法构建表达IbpB蛋白的重组质粒pBAD-ibpB,pBAD质粒为对照,转化到BW25113-ΔibpB菌株。转化pBAD-ibpB质粒的BW25113-ΔibpB菌株在45℃热处理之后加入甲醛进行交联,亲和层析法对交联产物进行纯化,质谱法对捕获的客户蛋白进行鉴定,过氧化氢酶活性测定和蛋白热聚集体分离的方法检测IbpB对其客户蛋白的作用。结果质谱鉴定结果表明IbpB在高温条件下互相作用的客户蛋白主要是过氧化氢酶KatG、色氨酸降解酶TnaA和延伸因子EF-Tu;在ibpB敲除株中回补IbpB可以减少过氧化氢酶在高温条件下的活性丧失,可以阻止TnaA和EF-Tu在高温条件下发生的热聚集。结论 KatG、TnaA和EF-Tu是IbpB在高温条件下相互作用的主要客户蛋白,IbpB在高温条件下对上述客户蛋白具有明显的保护作用。%Objective To investigate the client proteins of small heat shock protein IbpB in Escherichia coli cells under a high temperature and the effect of IbpB on its client proteins at this temperature.Methods A recombinant vec-tor pBAD-ibpaB was constructed which could express IbpB protein, while the vector pBAD was used as a control.Both vectors were transfected into Escherichia coli BW25113-ΔibpB cell and then heated at 45℃ before formaldehyde cross-linking.The resultant products were purified by affinity chromatography, and the client proteins of interest were identified by mass spectrometry.Finally, the effects of IbpB on these client proteins under a high temperature were determined by catalase activity assay and protein thermal aggregation isolation.Results According to mass spectrometry, the client proteins interacting with IbpB under a high temperature included catalase KatG, tryptophanase TnaA and elongation factor EF-Tu.The addition of IbpB in

  20. INVESTIGATION OF MICROSTRUCTURE AND CONDUCTIVE MECHANISM OF HIGH DENSITY POLYETHYLENE/CARBON BLACK PARTICLE COMPOSITE BY POSITRON ANNIHILATION LIFETIME SPECTROSCOPY

    Institute of Scientific and Technical Information of China (English)

    Yang-mei Fan; Xian-fenga Zhang; Bang-jiao Ye; Xian-yi Zhou; Hui-min Weng; Jiang-feng Du; Rong-dian Han; Shao-jin Jia; Zhi-cheng Zhang

    2002-01-01

    The microstmcture and conductive mechanism of high density polyethylene/carbon black (HDPE/CB) composite were investigated by positron annihilation lifetime spectroscopy (PALS). The PALS were measured in two series of samples,one with various CB contents in the composites and the other with various γ-irradiation doses in HDPE/CB composite containing 20 wt% CB. It was found that CB particles distribute in the amorphous regions, the CB critical content value in HDPE/CB composite is about 16.7 wt% and the suitable γ-irradiation dose for improving the conductive behavior of HDPE/CB composite is about 20 Mrad. The result observed for the second set of samples suggests that γ-irradiation causes not only cross-linking in amorphous regions but also destruction of the partial crystalline structure. Therefore, a suitable irradiation dose, about 20 Mrad, can induce sufficient cross-linking in the amorphous regions without enhancing the decomposition of crystalline structure, so that the positive temperature coefficient (PTC) effect remains while the negative temperature coefficient (NTC) effect is suppressed. A new interpretation of the conductive mechanism, which might provide a more detailed explanation of the PTC effect and the NTC effect has been proposed.

  1. Mass spectrometric analysis of a UV-cross-linked protein-DNA complex: tryptophans 54 and 88 of E. coli SSB cross-link to DNA

    DEFF Research Database (Denmark)

    Steen, H; Petersen, J; Mann, M

    2001-01-01

    of two different peptide-DNA heteroconjugates was accomplished by matrix-assisted laser desorption/ionization mass spectrometry and allowed assignment of tryptophan-54 and tryptophan-88 as candidate cross-linked residues. Sequencing of those peptide-DNA heteroconjugates by nanoelectrospray quadrupole...

  2. Tissue-specific effects of aldose reductase inhibition on fluorescence and cross-linking of extracellular matrix in chronic galactosemia. Relationship to pentosidine cross-links.

    Science.gov (United States)

    Richard, S; Tamas, C; Sell, D R; Monnier, V M

    1991-08-01

    Chronic experimental hyperglycemia mediated by galactose has been shown to induce browning and cross-linking of rat tail tendon collagen that could be duplicated in vitro by nonenzymatic galactosylation. To investigate the nature of these changes, Sprague-Dawley rats were placed on a 33% galactose diet without and with sorbinil for 6 and 12 mo. Collagen-linked fluorescence and pentosidine cross-links increased with age and galactosemia in tail tendons (P less than 0.001) and skin but were essentially unresponsive to aldose reductase inhibition (ARI). In contrast, tendon breaking time in urea, a likely parameter of cross-linking, was markedly improved (P less than 0.001) by ARI. Fluorescence that was inhibited by sorbinil treatment was increased in pepsin and proteinase K digest of aortic tissue from galactosemic rats (P less than 0.001), but impaired enzymatic digestibility was not observed. Systolic blood pressure as potential consequence of aortic stiffening was not increased in galactosemia. These data suggest that fluorescence in skin and tendon might be in part due to advanced glycosylation and pentosidine formation because these were not decreased by ARI. However, they also suggest that nonfluorescent cross-links may also be forming because, in contrast to fluorescence, tail tendon breaking time was partly corrected by ARI. Thus, it appears that extracellular matrix changes in chronic galactosemia are complex, being partly attributable to advanced glycosylation and partly to polyol-pathway activation.

  3. Inverted bulk-heterojunction solar cell with cross-linked hole-blocking layer

    Science.gov (United States)

    Udum, Yasemin; Denk, Patrick; Adam, Getachew; Apaydin, Dogukan H.; Nevosad, Andreas; Teichert, Christian; S. White, Matthew.; S. Sariciftci, Niyazi.; Scharber, Markus C.

    2014-01-01

    We have developed a hole-blocking layer for bulk-heterojunction solar cells based on cross-linked polyethylenimine (PEI). We tested five different ether-based cross-linkers and found that all of them give comparable solar cell efficiencies. The initial idea that a cross-linked layer is more solvent resistant compared to a pristine PEI layer could not be confirmed. With and without cross-linking, the PEI layer sticks very well to the surface of the indium–tin–oxide electrode and cannot be removed by solvents used to process PEI or common organic semiconductors. The cross-linked PEI hole-blocking layer functions for multiple donor–acceptor blends. We found that using cross-linkers improves the reproducibility of the device fabrication process. PMID:24817837

  4. Molecular Dynamics Simulations of Polymer Networks Undergoing Sequential Cross-Linking and Scission Reactions

    DEFF Research Database (Denmark)

    Rottach, Dana R.; Curro, John G.; Budzien, Joanne;

    2007-01-01

    The effects of sequential cross-linking and scission of polymer networks formed in two states of strain are investigated using molecular dynamics simulations. Two-stage networks are studied in which a network formed in the unstrained state (stage 1) undergoes additional cross-linking in a uniaxia......The effects of sequential cross-linking and scission of polymer networks formed in two states of strain are investigated using molecular dynamics simulations. Two-stage networks are studied in which a network formed in the unstrained state (stage 1) undergoes additional cross...... good agreement with the predictions of Flory and Fricker. It was found that the fractional stress reduction upon removal of the first-stage cross-links could be accurately calculated from the slip tube model of Rubinstein and Panyukov modified to use the theoretical transfer functions of Fricker.  ...

  5. Hydrogen peroxide and ferulic acid-mediated oxidative cross-linking ...

    African Journals Online (AJOL)

    STORAGESEVER

    2009-12-15

    Dec 15, 2009 ... Oxidative cross-linked casein mediated by hydrogen peroxide and ferulic acid was prepared at ... functional properties of food proteins treated (Motoki and. Seguro, 1998 ..... Team of Northeast Agricultural University (No.

  6. CrossWork: Software-assisted identification of cross-linked peptides

    DEFF Research Database (Denmark)

    Rasmussen, Morten; Refsgaard, Jan; Peng, Li;

    2011-01-01

    The increased interest in chemical cross-linking for probing protein structure and interaction has led to a large increase in literature describing new cross-linkers and search programs. However, this has not led to a corresponding increase in the analysis of large and complex proteins. A major...... obstacle is that the new cross-linkers are either not readily available and/or have a low reactivity. In combination with aging search programs that are slow and have low sensitivity, or new search programs that are described but not released, these efforts do little to advance the field of cross......-linking. Here we present a method pipeline for chemical cross-linking, using two standard cross-linkers, BS3 and BS2G, combined with our freely available CrossWork search program. By this approach we generate cross-link data sufficient to derive structural information for large and complex proteins. Cross...

  7. A Review of Collagen Cross-Linking in Cornea and Sclera

    Directory of Open Access Journals (Sweden)

    Xiao Zhang

    2015-01-01

    Full Text Available Riboflavin/UVA cross-linking is a technique introduced in the past decades for the treatment of keratoconus, keratectasia, and infectious keratitis. Its efficacy and safety have been investigated with clinical and laboratory studies since its first clinical application by Wollensak for the treatment of keratoconus. Although its complications are encountered during clinical practice, such as infection inducing risk, minimal invasion merits a further investigation on its future application in clinical practice. Recently, collagen cross-linking in sclera shows a promising prospect. In present study, we summarized the representative studies describing the clinical and laboratory application of collagen cross-linking published in past decades and provided our opinion on the positive and negative results of cross-linking in the treatment of ophthalmic disorders.

  8. New insights into the pros and cons of cross-linking decellularized bioartificial organs.

    Science.gov (United States)

    Hussein, Kamal H; Park, Kyung-Mee; Lee, Yun-Suk; Woo, Jae-Seok; Kang, Byung-Jae; Choi, Ki-Young; Kang, Kyung-Sun; Woo, Heung-Myong

    2017-01-25

    ABSTRACTDecellularization is an attractive method for scaffold designing in regenerative medicine. The resulting extracellular matrix (ECM) consists of structural proteins such as collagen and elastin, growth factors, and glycosaminoglycans, which can direct site-appropriate remodeling after in vivo implantation. Mainly, collagen and elastin of ECM are exposed to the enzymatic biodegradation in the host. To control the biodegradation process, treatment of decellularized tissue by a cross-linking agent is required. Cross-linking also reduces antigenicity and increases the storage properties. Cross-linkers should be nontoxic, with the ability to preserve the ECM components, especially glycosaminoglycans and associated growth factors for retention of scaffold bioactivity. In this review, we describe the different cross-linking agents and methods of evaluation of cross-linking efficiency.

  9. Plasticizer migration from cross-linked flexible PVC. 1. Effects on tribology

    Science.gov (United States)

    Pannico, M.; Persico, P.; Ambrogi, V.; Carfagna, C.

    2010-06-01

    Utilization of soft PVC is restricted by plasticizer migration that can affect material properties, as well as its toxicity. Modifying the chemical structure of PVC is one of the most effective tool to reduce the diffusion of plasticizer. In this work, a soft cross-linked PVC was obtained using a difunctional amine, namely isophoron diamine (IPDA) as the cross-linking agent. The gel content (wt %) was evaluated by weighting the insoluble portion obtained through solvent extraction technique. Thermogravimetric analysis (TGA) revealed that cross-linking reactions promote thermal degradation phenomena in the polymer matrix. Tribological properties of soft uncross-linked, cross-linked and rigid PVC were determined. Soft formulations were held in contact for 32 days with rigid PVC sheets. Plasticizer migration towards the interface causes an increase of dynamic friction compared to that of the reference rigid PVC.

  10. Two-color QCD at high density

    Energy Technology Data Exchange (ETDEWEB)

    Boz, Tamer; Skullerud, Jon-Ivar [Department of Mathematical Physics, Maynooth University, Maynooth, Co. Kildare (Ireland); Centre for the Subatomic Structure of Matter, Adelaide University, Adelaide, SA 5005 (Australia); Giudice, Pietro [Universität Münster, Institut für Theoretische Physik, Münster (Germany); Hands, Simon [Department of Physics, College of Science, Swansea University, Swansea (United Kingdom); Williams, Anthony G. [Centre for the Subatomic Structure of Matter, Adelaide University, Adelaide, SA 5005 (Australia)

    2016-01-22

    QCD at high chemical potential has interesting properties such as deconfinement of quarks. Two-color QCD, which enables numerical simulations on the lattice, constitutes a laboratory to study QCD at high chemical potential. Among the interesting properties of two-color QCD at high density is the diquark condensation, for which we present recent results obtained on a finer lattice compared to previous studies. The quark propagator in two-color QCD at non-zero chemical potential is referred to as the Gor’kov propagator. We express the Gor’kov propagator in terms of form factors and present recent lattice simulation results.

  11. Preparation and characterization of stable cross-linked enzyme aggregates of novel laccase enzyme from Shewanella putrefaciens and using malachite green decolorization.

    Science.gov (United States)

    Sinirlioglu, Zeynep Aydin; Sinirlioglu, Deniz; Akbas, Fahri

    2013-10-01

    A novel type laccase from Shewanella putrefaciens was identified, expressed in Escherichia coli, characterized, prepared in cross-linked enzyme aggregates (CLEA) for industrial applications and investigated of decolorization activity on malchite green dye. Enzyme characterization was investigated by enzyme assay, SDS-PAGE and other biochemical reactions. Moreover, cross-linked enzyme aggregates were prepared and characterized. Saturated ammonium sulphate solution was used as the precipitating agent and cross linked with glutaraldehyde. These CLEA-laccase aggregates showed more catalytic efficiency and more stabilities compared to free laccase against harsh conditions of thermal and chemical agents as well as high reusability. Also it showed more decolorization ability. These results suggest that this CLEA is potentially usable in industrial applications. Copyright © 2013 Elsevier Ltd. All rights reserved.

  12. The level of cross-linking and the structure of anisotropic magnetorheological elastomers

    Energy Technology Data Exchange (ETDEWEB)

    Borin, Dmitry, E-mail: dmitry.borin@tu-dresden.de [Institute of Fluid Mechanics, Technische Universitaet Dresden, Dresden 01062 (Germany); Guenther, David [Institute of Fluid Mechanics, Technische Universitaet Dresden, Dresden 01062 (Germany); Hintze, Christian; Heinrich, Gert [Leibniz Institute of Polymer Research, Dresden 01069 (Germany); Odenbach, Stefan [Institute of Fluid Mechanics, Technische Universitaet Dresden, Dresden 01062 (Germany)

    2012-10-15

    The influence of the concentration of the magnetic powder on the level of cross-linking of magnetorheological elastomers (MREs) has been studied. Afterwards the structural characterisation of manufactured MREs has been performed by using non-destructive method, specifically the computed tomography. The correlation between internal structures of MREs and the developing of its cross-linking level during the curing was found. It was shown that changes in the concentration of the powder significantly affect morphologies of the sample.

  13. Analysis of glycation induced protein cross-linking inhibitory effects of some antidiabetic plants and spices

    OpenAIRE

    Perera, Handunge Kumudu Irani; Handuwalage, Charith Sandaruwan

    2015-01-01

    Background Protein cross-linking which occurs towards the latter part of protein glycation is implicated in the development of chronic diabetic complications. Glycation induced protein cross-linking inhibitory effects of nine antidiabetic plants and three spices were evaluated in this study using a novel, simple, electrophoresis based method. Methods Methanol extracts of thirteen plants including nine antidiabetic plants and three spices were used. Lysozyme and fructose were incubated at 37 °...

  14. Porphyrin-induced photodynamic cross-linking of hepatic heme-binding proteins.

    Science.gov (United States)

    Vincent, S H; Holeman, B; Cully, B C; Muller-Eberhard, U

    1986-01-27

    Three types of hepatic proteins, a heme-binding Z protein, a mixture of the glutathione S-transferases and a cytochrome P450 isozyme, were shown to be susceptible to photodynamic cross-linking and loss in antigenicity by naturally occurring porphyrins. At 50 microM, uroporphyrin caused the most and protoporphyrin the least photodecomposition. Hemopexin, a specific serum heme carrier, was photodecomposed but no cross-linking was detected. Heme and scavengers of singlet oxygen partially prevented protein photodecomposition.

  15. Smooth muscle cell phenotype modulation and contraction on native and cross-linked polyelectrolyte multilayers.

    Science.gov (United States)

    Moussallem, Maroun D; Olenych, Scott G; Scott, Shannon L; Keller, Thomas C S; Schlenoff, Joseph B

    2009-11-09

    Smooth muscle cells convert between a motile, proliferative "synthetic" phenotype and a sessile, "contractile" phenotype. The ability to manipulate the phenotype of aortic smooth muscle cells with thin biocompatible polyelectrolyte multilayers (PEMUs) with common surface chemical characteristics but varying stiffness was investigated. The stiffness of (PAH/PAA) PEMUs was varied by heating to form covalent amide bond cross-links between the layers. Atomic force microscopy (AFM) showed that cross-linked PEMUs were thinner than those that were not cross-linked. AFM nanoindentation demonstrated that the Young's modulus ranged from 6 MPa for hydrated native PEMUs to more than 8 GPa for maximally cross-linked PEMUs. Rat aortic A7r5 smooth muscle cells cultured on native PEMUs exhibited morphology and motility of synthetic cells and expression of the synthetic phenotype markers vimentin, tropomyosin 4, and nonmuscle myosin heavy chain IIB (nmMHCIIB). In comparison, cells cultured on maximally cross-linked PEMUs exhibited the phenotype markers calponin, smooth muscle myosin heavy chain (smMHC), myocardin, transgelin, and smooth muscle alpha-actin (smActin) that are characteristic of the smooth muscle "contractile" phenotype. Consistent with those cells being "contractile", A7r5 cells grown on cross-linked PEMUs produced contractile force when stimulated with a Ca(2+) ionophore.

  16. Cross-linked survey analysis is an approach for separating cause and effect in survey research.

    Science.gov (United States)

    Redelmeier, Donald A; Thiruchelvam, Deva; Lustig, Andrew J

    2015-01-01

    We developed a new research approach, called cross-linked survey analysis, to explore how an acute exposure might lead to changes in survey responses. The goal was to identify associations between exposures and outcomes while reducing some ambiguities related to interpreting cause and effect in survey responses from a population-based community questionnaire. Cross-linked survey analysis differs from a cross-sectional, longitudinal, and panel survey analysis by individualizing the timeline to the unique history of each respondent. Cross-linked survey analysis, unlike a repeated-measures self-matching design, does not track changes in a repeated survey question given to the same respondent at multiple time points. Pilot data from three analyses (n = 1,177 respondents) illustrate how a cross-linked survey analysis can control for population shifts, temporal trends, and reverse causality. Accompanying graphs provide an intuitive display to readers, summarize results, and show differences in response distributions. Population-based individual-level linkages also reduce selection bias and increase statistical power compared with a single-center cross-sectional survey. Cross-linked survey analysis has limitations related to unmeasured confounding, pragmatics, survivor bias, statistical models, and the underlying artifacts in survey responses. We suggest that a cross-linked survey analysis may help in epidemiology science using survey data. Copyright © 2015 Elsevier Inc. All rights reserved.

  17. Exogenous collagen cross-linking recovers tendon functional integrity in an experimental model of partial tear.

    Science.gov (United States)

    Fessel, Gion; Wernli, Jeremy; Li, Yufei; Gerber, Christian; Snedeker, Jess G

    2012-06-01

    We investigated the hypothesis that exogenous collagen cross-linking can augment intact regions of tendon to mitigate mechanical propagation of partial tears. We first screened the low toxicity collagen cross-linkers genipin, methylglyoxal and ultra-violet (UV) light for their ability to augment tendon stiffness and failure load in rat tail tendon fascicles (RTTF). We then investigated cross-linking effects in load bearing equine superficial digital flexor tendons (SDFT). Data indicated that all three cross-linking agents augmented RTTF mechanical properties but reduced native viscoelasticity. In contrast to effects observed in fascicles, methylglyoxal treatment of SDFT detrimentally affected tendon mechanical integrity, and in the case of UV did not alter tendon mechanics. As in the RTTF experiments, genipin cross-linking of SDFT resulted in increased stiffness, higher failure loads and reduced viscoelasticity. Based on this result we assessed the efficacy of genipin in arresting tendon tear propagation in cyclic loading to failure. Genipin cross-linking secondary to a mid-substance biopsy-punch significantly reduced tissue strains, increased elastic modulus and increased resistance to fatigue failure. We conclude that genipin cross-linking of injured tendons holds potential for arresting tendon tear progression, and that implications of the treatment on matrix remodeling in living tendons should now be investigated.

  18. A Comparative Study of the Characteristics of Cross-Linked, Oxidized and Dual-Modified Rice Starches

    Directory of Open Access Journals (Sweden)

    Feng-Xiang Yu

    2012-09-01

    Full Text Available Rice starch was cross-linked with epichlorohydrin (0.3%, w/w, on a dry starch basis and oxidized with sodium hypochlorite (2.5% w/w, respectively. Two dual-modified rice starch samples (oxidized cross-linked rice starch and cross-linked oxidized rice starch were obtained by the oxidation of cross-linked rice starch and the cross-linking of oxidized rice starch at the same level of reagents. The physicochemical properties of native rice starch, cross-linked rice starch and oxidized rice starch were also studied parallel with those of the two dual-modified rice starch samples using rapid visco analysis (RVA, differential scanning calorimetry (DSC, dynamic rheometry and scanning electron microscopy (SEM. It was found that the levels of cross-linking and oxidation used in this study did not cause any significant changes in the morphology of rice starch granules. Cross-linked oxidized starch showed lower swelling power (SP and solubility, and higher paste clarity in comparison with native starch. Cross-linked oxidized rice starch also had the lowest tendency of retrogradation and highest ability to resistant to shear compared with native, cross-linked, oxidized and oxidized cross-linked rice starches. These results suggest that the undesirable properties in native, cross-linked and oxidized rice starch samples could be overcome through dual-modification.

  19. Effect of hormone replacement therapy on the bone mass and urinary excretion of pyridinium cross-links

    Directory of Open Access Journals (Sweden)

    Dolores Perovano Pardini

    2000-01-01

    Full Text Available CONTEXT: The menopause accelerates bone loss and is associated with an increased bone turnover. Bone formation may be evaluated by several biochemical markers. However, the establishment of an accurate marker for bone resorption has been more difficult to achieve. OBJECTIVE: To study the effect of hormone replacement therapy (HRT on bone mass and on the markers of bone resorption: urinary excretion of pyridinoline and deoxypyridinoline. DESIGN: Cohort correlational study. SETTING: Academic referral center. SAMPLE: 53 post-menopausal women, aged 48-58 years. MAIN MEASUREMENTS: Urinary pyr and d-pyr were measured in fasting urine samples by spectrofluorometry after high performance liquid chromatography and corrected for creatinine excretion measured before treatment and after 1, 2, 4 and 12 months. Bone mineral density (BMD was measured by dual energy X-ray absorptiometry (DEXA before treatment and after 12 months of HRT. RESULTS: The BMD after HRT was about 4.7% (P < 0.0004; 2% (P < 0.002; and 3% (P < 0.01 higher than the basal values in lumbar spine, neck and trochanter respectively. There were no significant correlations between pyridinium cross-links and age, weight, menopause duration and BMD. The decrease in pyr and d-pyr was progressive after HRT, reaching 28.9% (P < 0.0002, and 42% (P < 0.0002 respectively after 1 year. CONCLUSIONS: Urinary pyridinoline and deoxypyridinoline excretion decreases early in hormone replacement therapy, reflecting a decrease in the bone resorption rate, and no correlation was observed with the bone mass evaluated by densitometry.

  20. Long term in vivo degradation and tissue response to photo-cross-linked elastomers prepared from star-shaped prepolymers of poly(epsilon-caprolactone-co-D,L-lactide).

    Science.gov (United States)

    Chapanian, Rafi; Tse, Man Y; Pang, Stephen C; Amsden, Brian G

    2010-03-01

    Long term in vivo degradation, and tissue response to, cylindrical elastomers made of photo-cross-linked star-poly(epsilon-caprolactone-co-D,L-lactide) triacrylate were investigated through subcutaneous implantation in rats. The elastomers were prepared via UV initiated crosslinking of prepolymers of equimolar amounts of monomers; a high crosslink density elastomer (ELAST 1250) was prepared from a prepolymer of 1250 Da and a low crosslink density elastomer (ELAST 7800) was prepared from a prepolymer of 7800 Da. The elastomers were characterized using cross-polarization magic angle spinning solid state (13)C NMR and attenuated total reflectance fourier transform infrared spectroscopy. The progress of the in vivo degradation process was followed by employing SEM, uniaxial tensile, mass loss, water uptake, and sol content measurements. The rate of in vivo degradation was faster than the rate of in vitro degradation for both ELAST 1250 and ELAST 7800. Long term in vivo degradation studies indicated that both elastomers undergo bulk hydrolysis along with surface erosion occurring due to the physiological environment. In the case of low cross-link density elastomers, the onset of mass loss was accompanied with an increase in both water uptake and sol content, whereas, in the case of high crosslink density elastomers, only the water uptake increased. This degradation pattern was due to crazing of the high crosslink density elastomers. ELAST 7800 cylinders were totally degraded, and ELAST 1250 cylinders had lost 80% of their mass, within 30 weeks. Aminor host reaction with minimal vascularity and inflammation was invoked, with a milder tissue response observed with more highly crosslinked cylinders.

  1. Method of high-density foil fabrication

    Energy Technology Data Exchange (ETDEWEB)

    Blue, Craig A.; Sikka, Vinod K.; Ohriner, Evan K.

    2003-12-16

    A method for preparing flat foils having a high density includes the steps of mixing a powdered material with a binder to form a green sheet. The green sheet is exposed to a high intensity radiative source adapted to emit radiation of wavelengths corresponding to an absorption spectrum of the powdered material. The surface of the green sheet is heated while a lower sub-surface temperature is maintained. An apparatus for preparing a foil from a green sheet using a radiation source is also disclosed.

  2. Characterization of a Cross-Linked Protein-Nucleic Acid Substrate Radical in the Reaction Catalyzed by RlmN

    Energy Technology Data Exchange (ETDEWEB)

    Silakov, Alexey; Grove, Tyler L.; Radle, Matthew I.; Bauerle, Matthew R.; Green, Michael T.; Rosenzweig, Amy C.; Boal, Amie K.; Booker, Squire J. [NWU; (Penn)

    2014-08-14

    RlmN and Cfr are methyltransferases/methylsynthases that belong to the radical S-adenosylmethionine superfamily of enzymes. RlmN catalyzes C2 methylation of adenosine 2503 (A2503) of 23S rRNA, while Cfr catalyzes C8 methylation of the exact same nucleotide, and will subsequently catalyze C2 methylation if the site is unmethylated. A key feature of the unusual mechanisms of catalysis proposed for these enzymes is the attack of a methylene radical, derived from a methylcysteine residue, onto the carbon center undergoing methylation to generate a paramagnetic protein–nucleic acid cross-linked species. This species has been thoroughly characterized during Cfr-dependent C8 methylation, but does not accumulate to detectible levels in RlmN-dependent C2 methylation. Herein, we show that inactive C118S/A variants of RlmN accumulate a substrate-derived paramagnetic species. Characterization of this species by electron paramagnetic resonance spectroscopy in concert with strategic isotopic labeling shows that the radical is delocalized throughout the adenine ring of A2503, although predominant spin density is on N1 and N3. Moreover, 13C hyperfine interactions between the radical and the methylene carbon of the formerly [methyl-13C]Cys355 residue show that the radical species exists in a covalent cross-link between the protein and the nucleic acid substrate. X-ray structures of RlmN C118A show that, in the presence of SAM, the substitution does not alter the active site structure compared to that of the wild-type enzyme. Together, these findings have new mechanistic implications for the role(s) of C118 and its counterpart in Cfr (C105) in catalysis, and suggest involvement of the residue in resolution of the cross-linked species via a radical mediated process

  3. HIGH DENSITY QCD WITH HEAVY-IONS

    CERN Multimedia

    The Addendum 1 to Volume 2 of the CMS Physics TDR has been published The Heavy-Ion analysis group completed the writing of a TDR summarizing the CMS plans in using heavy ion collisions to study high density QCD. The document was submitted to the LHCC in March and presented in the Open Session of the LHCC on May 9th. The study of heavy-ion physics at the LHC is promising to be very exciting. LHC will open a new energy frontier in ultra-relativistic heavy-ion physics. The collision energy of heavy nuclei at sNN = 5.5 TeV will be thirty times larger than what is presently available at RHIC. We will certainly probe quark and gluon matter at unprecedented values of energy density. The prime goal of this research programme is to study the fundamental theory of the strong interaction - Quantum Chromodynamics (QCD) - in extreme conditions of temperature, density and parton momentum fraction (low-x). Such studies, with impressive experimental and theoretical advances in recent years thanks to the wealth of high-qua...

  4. An investigation on chloroprene-compatibilized acrylonitrile butadiene rubber/high density polyethylene blends

    Directory of Open Access Journals (Sweden)

    Khalil Ahmed

    2015-11-01

    Full Text Available Blends of acrylonitrile butadiene rubber/high density polyethylene (NBR/HDPE compatibilized by Chloroprene rubber (CR were prepared. A fixed quantity of industrial waste such as marble waste (MW, 40 phr was also included. The effect of the blend ratio and CR on cure characteristics, mechanical and swelling properties of MW-filled NBR/HDPE blends was investigated. The results showed that the MW-filled NBR/HDPE blends revealed an increase in tensile strength, tear, modulus, hardness and cross-link density for increasing weight ratio of HDPE. The minimum torque (ML and maximum torque (MH of blends increased with increasing weight ratio of HDPE while scorch time (ts2 cure time (tc90, compression set and abrasion loss of blends decreased with increasing weight ratio of HDPE. The blends also showed a continuous reduction in elongation at break as well as swelling coefficient with increasing HDPE amount in blends. MW filled blends based on CR provided the most encouraging balance values of overall properties.

  5. Cross-linking of rabbit skeletal muscle troponin subunits: labeling of cysteine-98 of troponin C with 4-maleimidobenzophenone and analysis of products formed in the binary complex with troponin T and the ternary complex with troponins I and T.

    Science.gov (United States)

    Leszyk, J; Collins, J H; Leavis, P C; Tao, T

    1988-09-06

    The sulfhydryl-specific, heterobifunctional, photoactivatable cross-linker 4-maleimidobenzophenone (BPMal) was used to study the interaction of rabbit skeletal muscle troponin subunits TnC, TnT, and TnI. TnC was labeled at Cys-98 by the maleimide moiety of BPMal and then mixed with either TnT alone or TnI plus TnT, in the presence of Ca2+. Upon photolysis, TnI and/or TnT formed covalent cross-links with TnC. The cross-linked TnC-TnT heterodimer obtained from the binary complex was digested into progressively smaller cross-linked peptides that were purified by HPLC and then characterized by amino acid analysis and sequencing. An initial cross-linked CNBr fraction contained the expected peptide CB9 (residues 84-135) of TnC, plus CNBr peptides spanning residues 152-230 of TnT. Results from a peptic digest of the CNBr cross-linked fraction permitted the identification of residues 159-197 as the most highly cross-linked region in TnT. A final subtilisin digest yielded a heterogeneous cross-linked fraction, which suggested that an especially high degree of cross-links was formed in the vicinity of residues 175-178 (Met-Lys-Lys-Lys) of TnT. Although this region of TnT had previously been implicated in binding, we show here for the first time that it is close to Cys-98 of TnC. In an analogous study on the binary complex of TnC and TnI [Leszyk, J., Collins, J. H., Leavis, P. C., & Tao, T. (1987) Biochemistry 26, 7042-7047], we previously showed that Cys-98 of TnC was cross-linked mainly to CN4, the "inhibitory region", of TnI.(ABSTRACT TRUNCATED AT 250 WORDS)

  6. Cross-linked carbon networks constructed from N-doped nanosheets with enhanced performance for supercapacitors

    Science.gov (United States)

    Liu, Qingqing; Zhong, Jialiang; Sun, Zhipeng; Mi, Hongyu

    2017-02-01

    Hierarchically porous carbons offer great benefits for constructing advanced electrodes for energy-related applications. Herein, we reported facile synthesis of cross-linked carbon networks (HPCNs) made from N-doped nanosheets. By using MgO as self-sacrificial templates, the polyethylene glycol and melamine precursors were first uniformly coated on the template, and then annealed at the elevated temperature in inert atmosphere before removing the templates by mild acid etching. Interestingly, the capacitance performance of HPCNs could be easily modulated by adjusting the mass ratio of the precursors and templates, as well as the carbonization temperature. The optimized HPCNs showed specific capacitances of 192.6 F g-1 at 1.0 A g-1 and 156.2 F g-1 even at 20 A g-1 in 6.0 M KOH solution, and long-term cyclability with 85.5% capacitance retention at high current load of 10 A g-1 after 8000 successive cycles, which were attributed to structural merits of these continuous networks including high surface area of 370.8 m2 g-1, high pore volume of 1.65 cm3 g-1, as well as high nitrogen content of 9.920 wt.%. Owing to simplicity of the synthesis method and superior performance, such HPCNs may promise great potential in energy storage fields.

  7. Silica-shell cross-linked micelles encapsulating fluorescent conjugated polymers for targeted cellular imaging.

    Science.gov (United States)

    Tan, Happy; Zhang, Yu; Wang, Miao; Zhang, Zhongxing; Zhang, Xinhai; Yong, Anna Marie; Wong, Siew Yee; Chang, Alex Yuang-chi; Chen, Zhi-Kuan; Li, Xu; Choolani, Mahesh; Wang, John

    2012-01-01

    A bioinspired silification approach was successfully used to encapsulate fluorescent conjugated polymers inside silica-shell cross-linked polymeric micelles (CP-SSCL) in the highly benign synthesis environment of room temperature and near-neutral aqueous environment. Four different conjugated polymers were employed to demonstrate the versatility of the bioinspired silification, resulting in the formation of CP-SSCL with different emission wavelengths across the visible spectrum. The CP-SSCL are characterized by a large absorption coefficient and high quantum yield, indicating that they exhibit the required high fluorescence brightness for cellular imaging application. In addition, the CP-SSCL also exhibit a high colloidal stability and low cytotoxicity. The in vitro studies of using MDA-MB-231 breast cancer cells show that the CP-SSCL are successfully uptaken by the cancer cells and located at the cytoplasm of the cells. Furthermore, by conjugating folic acid on their surfaces, the uptake of CP-SSCL by MDA-MB-231 cells was enhanced significantly, suggesting their great potential for targeted imaging and early detection of cancer cells.

  8. Click Cross-Linking-Improved Waterborne Polymers for Environment-Friendly Coatings and Adhesives.

    Science.gov (United States)

    Hu, Jianqing; Peng, Kaimei; Guo, Jinshan; Shan, Dingying; Kim, Gloria B; Li, Qiyao; Gerhard, Ethan; Zhu, Liang; Tu, Weiping; Lv, Weizhong; Hickner, Michael A; Yang, Jian

    2016-07-13

    Waterborne polymers, including waterborne polyurethanes (WPU), polyester dispersions (PED), and polyacrylate emulsions (PAE), are employed as environmentally friendly water-based coatings and adhesives. An efficient, fast, stable, and safe cross-linking strategy is always desirable to impart waterborne polymers with improved mechanical properties and water/solvent/thermal and abrasion resistance. For the first time, click chemistry was introduced into waterborne polymer systems as a cross-linking strategy. Click cross-linking rendered waterborne polymer films with significantly improved tensile strength, hardness, adhesion strength, and water/solvent resistance compared to traditional waterborne polymer films. For example, click cross-linked WPU (WPU-click) has dramatically improved the mechanical strength (tensile strength increased from 0.43 to 6.47 MPa, and Young's modulus increased from 3 to 40 MPa), hardness (increased from 59 to 73.1 MPa), and water resistance (water absorption percentage dropped from 200% to less than 20%); click cross-linked PED (PED-click) film also possessed more than 3 times higher tensile strength (∼28 MPa) than that of normal PED (∼8 MPa). The adhesion strength of click cross-linked PAE (PAE-click) to polypropylene (PP) was also improved (from 3 to 5.5 MPa). In addition, extra click groups can be preserved after click cross-linking for further functionalization of the waterborne polymeric coatings/adhesives. In this work, we have demonstrated that click modification could serve as a convenient and powerful approach to significantly improve the performance of a variety of traditional coatings and adhesives.

  9. Biodegradation of differently cross-linked collagen membranes: an experimental study in the rat.

    Science.gov (United States)

    Rothamel, Daniel; Schwarz, Frank; Sager, Martin; Herten, Monika; Sculean, Anton; Becker, Jürgen

    2005-06-01

    The aim of the present study was to compare the biodegradation of differently cross-linked collagen membranes in rats. Five commercially available and three experimental membranes (VN) were included: (1) BioGide (BG) (non-cross-linked porcine type I and III collagens), (2) BioMend (BM), (3) BioMendExtend (BME) (glutaraldehyde cross-linked bovine type I collagen), (4) Ossix (OS) (enzymatic-cross-linked bovine type I collagen), (5) TutoDent (TD) (non-cross-linked bovine type I collagen, and (6-8) VN(1-3) (chemical cross-linked porcine type I and III collagens). Specimens were randomly allocated in unconnected subcutaneous pouches separated surgically on the back of 40 wistar rats, which were divided into five groups (2, 4, 8, 16, and 24 weeks), including eight animals each. After 2, 4, 8, 16, and 24 weeks of healing, the rats were sacrificed and explanted specimens were prepared for histologic and histometric analysis. The following parameters were evaluated: biodegradation over time, vascularization, tissue integration, and foreign body reaction. Highest vascularization and tissue integration was noted for BG followed by BM, BME, and VN(1); TD, VN(2), and VN(3) showed prolongated, while OS exhibited no vascularization. Subsequently, biodegradation of BG, BM, BME and VN(1) was faster than TD, VN(2), and VN(3). OS showed only a minute amount of superficial biodegradation 24 weeks following implantation. Biodegradation of TD, BM, BME, VN(2), and VN(3) was associated with the presence of inflammatory cells. Within the limits of the present study, it was concluded that cross-linking of bovine and porcine-derived collagen types I and III was associated with (i) prolonged biodegradation, (ii) decreased tissue integration and vascularization, and (iii) in case of TD, BM, BME, VN(2), and VN(3) foreign body reactions.

  10. Peroxide cross-linked UHMWPE blended with vitamin E.

    Science.gov (United States)

    Oral, Ebru; Doshi, Brinda N; Gul, Rizwan M; Neils, Andrew L; Kayandan, Sanem; Muratoglu, Orhun K

    2016-04-15

    Radiation crosslinked ultrahigh molecular weight polyethylene (UHMWPE) is the bearing surface material most commonly used in total joint arthroplasty because of its excellent wear resistance. Crosslinking agents such as peroxides can also effectively increase wear resistance but peroxide crosslinked UHMWPE has low oxidative stability. We hypothesized that the addition of an antioxidant to peroxide crosslinked UHMWPE could improve its oxidation resistance and result in mechanical, tribological, and oxidative properties equivalent to currently utilized radiation crosslinked UHMWPEs. Various vitamin E (0.1-1.0 wt % and peroxide concentration (0.5-1.5 wt %) combinations were studied to investigate changes in crosslink density, wear rate, mechanical properties, and oxidative stability in comparison to radiation crosslinked UHMWPE. Peroxide crosslinking was more efficient as compared to radiation crosslinking in the presence of vitamin E with the former resulting in lower wear rate with vitamin E concentrations above 0.3 wt %. The tensile mechanical properties were comparable to and the impact strength was higher than those of the clinically relevant radiation crosslinked controls. We also determined that gamma sterilization of peroxide crosslinked vitamin E blends improved wear resistance further. In summary, peroxide crosslinking of vitamin E-blended UHMWPE may provide a feasible and economical alternative to radiation for achieving clinically relevant properties for total joint implants using UHMWPE. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2016.

  11. High Spectral Density Optical Communication Technologies

    CERN Document Server

    Nakazawa, Masataka; Miyazaki, Tetsuya

    2010-01-01

    The latest hot topics of high-spectral density optical communication systems using digital coherent optical fibre communication technologies are covered by this book. History and meaning of a "renaissance" of the technology, requirements to the Peta-bit/s class "new generation network" are also covered in the first part of this book. The main topics treated are electronic and optical devices, digital signal processing including forward error correction, modulation formats as well as transmission and application systems. The book serves as a reference to researchers and engineers.

  12. Beyond the local density approximation : improving density functional theory for high energy density physics applications.

    Energy Technology Data Exchange (ETDEWEB)

    Mattsson, Ann Elisabet; Modine, Normand Arthur; Desjarlais, Michael Paul; Muller, Richard Partain; Sears, Mark P.; Wright, Alan Francis

    2006-11-01

    A finite temperature version of 'exact-exchange' density functional theory (EXX) has been implemented in Sandia's Socorro code. The method uses the optimized effective potential (OEP) formalism and an efficient gradient-based iterative minimization of the energy. The derivation of the gradient is based on the density matrix, simplifying the extension to finite temperatures. A stand-alone all-electron exact-exchange capability has been developed for testing exact exchange and compatible correlation functionals on small systems. Calculations of eigenvalues for the helium atom, beryllium atom, and the hydrogen molecule are reported, showing excellent agreement with highly converged quantumMonte Carlo calculations. Several approaches to the generation of pseudopotentials for use in EXX calculations have been examined and are discussed. The difficult problem of finding a correlation functional compatible with EXX has been studied and some initial findings are reported.

  13. Morphological and functional correlations in riboflavin UV A corneal collagen cross-linking for keratoconus.

    Science.gov (United States)

    Mazzotta, Cosimo; Caporossi, Tomaso; Denaro, Rosario; Bovone, Cristina; Sparano, Caterina; Paradiso, Anna; Baiocchi, Stefano; Caporossi, Aldo

    2012-05-01

    To investigate the correlations between corneal structural modifications assessed by in vivo corneal confocal microscopy with visual function [uncorrected visual acuity (UCVA), best spectacle-corrected visual acuity (BSCVA)] and morphological data (corneal topography, pachymetry, elevation analysis) after riboflavin UV A corneal collagen cross-linking (CXL) for the stabilization of progressive keratoconus. Forty-four eyes with progressive keratoconus were enrolled in the Siena Eye Cross Study (prospective nonrandomized phase II open trial). All eyes underwent Riboflavin UV A CXL. Preoperative and postoperative evaluation comprised: UCVA, BSCVA, optical pachymetry (Visante OCT, Zeiss, Germany), corneal topography (CSO, Florence, Italy) and tomography (Orbscan IIz; B&L, Rochester, NY, USA) and in vivo confocal microscopy (Heidelberg Retina Tomograph II; Rostock, Heidelberg Gmbh, Germany). Examinations were performed preoperatively 6 months and one day before treatment and at 1, 3, 6 and 12 months of follow-up. In vivo corneal confocal microscopy showed time-dependent postoperative epithelial and stromal modifications after cross-linking. Epithelial thinning associated with stromal oedema and keratocytes apoptosis explained initial tendency towards slightly reduced VA and more glare one month postoperatively in 70% of eyes. Furthermore, a statistically not significant early worsening of topographic mean K values was observed. Orbscan II analysis significantly underestimated pachymetric values after treatment. Pachymetric underestimation was rectified by high-resolution optical pachymetry provided by the Visante OCT system. After the third post-CXL month, epithelial thickening, disappearance of oedema and new collagen compaction recorded by in vivo corneal confocal microscopy explained the improvements in visual performance during the follow-up. Changes in stromal reflectivity and collagen compaction observed by in vivo confocal microscopy were associated with corneal

  14. Biomimetic hydration lubrication with various polyelectrolyte layers on cross-linked polyethylene orthopedic bearing materials.

    Science.gov (United States)

    Kyomoto, Masayuki; Moro, Toru; Saiga, Kenichi; Hashimoto, Masami; Ito, Hideya; Kawaguchi, Hiroshi; Takatori, Yoshio; Ishihara, Kazuhiko

    2012-06-01

    Natural joints rely on fluid thin-film lubrication by the hydrated polyelectrolyte layer of cartilage. However, current artificial joints with polyethylene (PE) surfaces have considerably less efficient lubrication and thus much greater wear, leading to osteolysis and aseptic loosening. This is considered a common factor limiting prosthetic longevity in total hip arthroplasty (THA). However, such wear could be mitigated by surface modification to mimic the role of cartilage. Here we report the development of nanometer-scale hydrophilic layers with varying charge (nonionic, cationic, anionic, or zwitterionic) on cross-linked PE (CLPE) surfaces, which could fully mimic the hydrophilicity and lubricity of the natural joint surface. We present evidence to support two lubrication mechanisms: the primary mechanism is due to the high level of hydration in the grafted layer, where water molecules act as very efficient lubricants; and the secondary mechanism is repulsion of protein molecules and positively charged inorganic ions by the grafted polyelectrolyte layer. Thus, such nanometer-scaled hydrophilic polymers or polyelectrolyte layers on the CLPE surface of acetabular cup bearings could confer high durability to THA prosthetics.

  15. In vivo Confocal Microscopy Report after Lasik with Sequential Accelerated Corneal Collagen Cross-Linking Treatment.

    Science.gov (United States)

    Mazzotta, Cosimo; Balestrazzi, Angelo; Traversi, Claudio; Caragiuli, Stefano; Caporossi, Aldo

    2014-01-01

    We report the first pilot qualitative confocal microscopic analysis of a laser in situ keratomileusis (Lasik) treatment combined with sequential high-fluence accelerated corneal collagen cross-linking, denominated Lasik XTra, by means of HRT II laser scanning in vivo confocal microscopy after a 6-month follow-up. After obtaining approval from the Siena University Hospital Institutional Review Board, a 33-year-old female patient underwent a Lasik XTra procedure in her left eye. Confocal analysis demonstrated induced slight corneal microstructural changes by the interaction between UV-A, riboflavin and corneal stromal collagen, beyond the interface to a depth of 160 µm, without adverse events at the interface and endothelial levels. This application may be considered a prophylactic biomechanical treatment, stiffening the intermediate corneal stroma to prevent corneal ectasia and stabilizing the clinical results of refractive surgery. According to our preliminary experiences, this combined approach may be useful in higher-risk Lasik patients for hyperopic treatments, high myopia and lower corneal thicknesses.

  16. Release effect of the active ingredients using a radiation cross linking technology

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, Seung Hyun; Ahn, Sung Jun; Park, Jong Seok; Jeong, Sung In; Gwon, Hui Jeong; Lim, Youn Mook [Research Division for Industry and Environment, Korea Atomic Energy Research Institute, Jeongeup (Korea, Republic of); Lee, Dong Yun [Dept. of Bioengineering, Division of Applied Chemical and Bio Engineering, Hanyang University, Seoul (Korea, Republic of)

    2015-12-15

    Typical radiation cross-linked hydrogels has the characteristic that high water content, but low emission efficiency of active ingredients. Therefore, the hydrogel was prepared by the addition to collagen, which is closely related to the formation of skin wrinkles in biocompatibility and highly water-soluble carboxymethyl cellulose sodium salt (CMC) in order to preparation of hydrogels has excellent emission efficiency of active ingredients. Hydrogels were prepared by dissolving CMC and collagen each of 0.5%, 10% concentration in deionized water. Then, prepared hydrogels are performed by gamma-radiation at 1, 3, 5 kGy irradiation dose. The results showed that the gel fraction of after irradiated 3 kGy hydrogel was higher than before irradiated gelation as long as the 55.3%. The swelling rate of irradiated 3 kGy hydrogel was lower than the non-irradiated sample. The compressive strength of 3 kGy irradiated hydrogel was the highest. The visco-elastic did not show any significant differences, even after irradiation. The CMC hydrogel in this study suggested a potential use as a material for the mask pack for improved emission efficiency of the active ingredient and anti-wrinkles.

  17. In vivo Confocal Microscopy Report after Lasik with Sequential Accelerated Corneal Collagen Cross-Linking Treatment

    Directory of Open Access Journals (Sweden)

    Cosimo Mazzotta

    2014-04-01

    Full Text Available We report the first pilot qualitative confocal microscopic analysis of a laser in situ keratomileusis (Lasik treatment combined with sequential high-fluence accelerated corneal collagen cross-linking, denominated Lasik XTra, by means of HRT II laser scanning in vivo confocal microscopy after a 6-month follow-up. After obtaining approval from the Siena University Hospital Institutional Review Board, a 33-year-old female patient underwent a Lasik XTra procedure in her left eye. Confocal analysis demonstrated induced slight corneal microstructural changes by the interaction between UV-A, riboflavin and corneal stromal collagen, beyond the interface to a depth of 160 µm, without adverse events at the interface and endothelial levels. This application may be considered a prophylactic biomechanical treatment, stiffening the intermediate corneal stroma to prevent corneal ectasia and stabilizing the clinical results of refractive surgery. According to our preliminary experiences, this combined approach may be useful in higher-risk Lasik patients for hyperopic treatments, high myopia and lower corneal thicknesses.

  18. Novel enzymatically cross-linked hyaluronan hydrogels support the formation of 3D neuronal networks.

    Science.gov (United States)

    Broguiere, Nicolas; Isenmann, Luca; Zenobi-Wong, Marcy

    2016-08-01

    Hyaluronan (HA) is an essential component of the central nervous system's extracellular matrix and its high molecular weight (MW) form has anti-inflammatory and anti-fibrotic properties relevant for regenerative medicine. Here, we introduce a new hydrogel based on high MW HA which is cross-linked using the transglutaminase (TG) activity of the activated blood coagulation factor XIII (FXIIIa). These HA-TG gels have significant advantages for neural tissue engineering compared to previous HA gels. Due to their chemical inertness in the absence of FXIIIa, the material can be stored long-term, is stable in solution, and shows no cytotoxicity. The gelation is completely cell-friendly due to the specificity of the enzyme and the gelation rate can be tuned from seconds to hours at physiological pH and independently of stiffness. The gels are injectable, and attach covalently to fibrinogen and fibrin, two common bioactive components in in vitro tissue engineering, as well as proteins present in vivo, allowing the gels to covalently bind to brain or spinal cord defects. These optimal chemical and bioactive properties of HA-TG gels enabled the formation of 3D neuronal cultures of unprecedented performance, showing fast neurite outgrowth, axonal and dendritic speciation, strong synaptic connectivity in 3D networks, and rapidly-occurring and long-lasting coordinated electrical activity.

  19. Synthesis, characterization and cytocompatibility of a poly(diol-tricarballylate) visible light photo-cross-linked biodegradable elastomer.

    Science.gov (United States)

    Shaker, Mohamed A; Doré, Jules J E; Younes, Husam M

    2010-01-01

    The synthesis, characterization and in vitro cytocompatibility of a new family of photo-cross-linked amorphous poly(diol-tricarballylate) (PDT) biodegradable elastomeric polyesters are reported. The synthesis was based on the polycondensation reaction between tricarballylic acid and alkylene diols, followed by acrylation. The prepared and acrylated poly(diol-tricarballylate) (APDT) was characterized by means of FT-IR, (1)H-NMR, GPC and DSC. Liquid-to-solid photo-curing was carried out by exposing the APDT to visible light in the presence of camphorquinone as a photoinitiator. The thermal properties, mechanical characteristics, sol content, long-term in vitro degradation and cytocompatibility of the prepared PDT elastomers were also reported. The mechanical and degradation properties of this new photocurable elastomer can be precisely controlled by varying the density of acrylate moieties in the matrix of the polymer, and through changes in the pre-polymer chain length. The use of visible light cross-linking, possibility of solventless drug loading, controllable mechanical properties and cytocompatibility of these new elastomers make them excellent candidates for use in controlled implantable drug-delivery systems of protein drugs and other biomedical applications.

  20. Effect of Cross-Linking on the Structure and Growth of Polymer Films Prepared by Interfacial Polymerization.

    Science.gov (United States)

    Berezkin, Anatoly V; Kudryavtsev, Yaroslav V

    2015-11-10

    Interfacial polymerization of tri- and bifunctional monomers (A3B2 polymerization) is investigated by dissipative particle dynamics to reveal an effect of cross-linking on the reaction kinetics and structure of the growing polymer film. Regardless of the comonomer reactivity and miscibility, the kinetics in an initially bilayer melt passes from the reaction to diffusion control. Within the crossover period, branched macromolecules undergo gelation, which drastically changes the scenario of the polymerization process. Comparison with the previously studied linear interfacial polymerization (Berezkin, A. V.; Kudryavtsev, Y. V. Linear Interfacial Polymerization: Theory and Simulations with Dissipative Particle Dynamics J. Chem. Phys. 2014, 141, 194906) shows similar conversion rates but very different product characteristics. Cross-linked polymer films are markedly heterogeneous in density, their average polymerization degree grows with the comonomer miscibility, and end groups are mostly trapped deeply in the film core. Products of linear interfacial polymerization demonstrate opposite trends as they are spontaneously homogenized by a convective flow of macromolecules expelled from the reactive zone to the film periphery, which we call the reactive extrusion effect and which is hampered in branched polymerization. Influence of the comonomer architecture on the polymer film characteristics could be used in various practical applications of interfacial polymerization, such as fabrication of membranes, micro- and nanocapsules and 3D printing.

  1. Effects of UV-Light and Silane Cross-Linking on the Properties of Polyethylene Cable Materials%紫外光与硅烷交联对聚乙烯电缆材料性能的影响

    Institute of Scientific and Technical Information of China (English)

    马宝红; 鲍文波; 姜国发; 高广刚

    2013-01-01

    In this paper,the cross-linking insulation cable materials based on linear low density polyethylene (LLDPE) resin was prepared by UV-light and silane cross-linking methods respectively.The effects of two kinds of cross-linking methods on properties were investigated.The experimental results demonstrated that the UV-light cross-linking method was more effective than the silane cross-linking method.The UV-light cross-linking polyethylene materials showed better properties,such as gel content,thermal contraction,ageing resistance and electric properties.%以线型低密度聚乙烯(LLDPE)为基体树脂,分别制备出紫外光交联与硅烷交联电缆用绝缘料.讨论了两种交联方法对聚乙烯绝缘材料性能的影响.结果表明:对于无色母填充的聚乙烯材料,紫外光交联后的样品在凝胶含量、热收缩、耐老化及电性能等方面均明显优于硅烷交联聚乙烯材料.

  2. Recycling of irradiated high-density polyethylene

    Science.gov (United States)

    Navratil, J.; Manas, M.; Mizera, A.; Bednarik, M.; Stanek, M.; Danek, M.

    2015-01-01

    Radiation crosslinking of high-density polyethylene (HDPE) is a well-recognized modification of improving basic material characteristics. This research paper deals with the utilization of electron beam irradiated HDPE (HDPEx) after the end of its lifetime. Powder of recycled HDPEx (irradiation dose 165 kGy) was used as a filler into powder of virgin low-density polyethylene (LDPE) in concentrations ranging from 10% to 60%. The effect of the filler on processability and mechanical behavior of the resulting mixtures was investigated. The results indicate that the processability, as well as mechanical behavior, highly depends on the amount of the filler. Melt flow index dropped from 13.7 to 0.8 g/10 min comparing the lowest and the highest concentration; however, the higher shear rate the lower difference between each concentration. Toughness and hardness, on the other hand, grew with increasing addition of the recycled HDPEx. Elastic modulus increased from 254 to 450 MPa and material hardness increased from 53 to 59 ShD. These results indicate resolving the problem of further recycling of irradiated polymer materials while taking advantage of the improved mechanical properties.

  3. High Energy Density aluminum/oxygen cell

    Science.gov (United States)

    Rudd, E. J.; Gibbons, D. W.

    An alternative to a secondary battery as the power source for vehicle propulsion is a fuel cell, an example of which is the metal/air cell using metals such as aluminum, zinc, or iron. Aluminum is a particularly attractive candidate, with high energy and power densities, environmentally acceptable and having a large, established industrial base for production and distribution. An aluminum/oxygen system is currently under development for a prototype unmanned, undersea vehicle (UUV) for the US navy and recent work has focussed upon low corrosion aluminum alloys, and an electrolyte management system for processing the by-products of the energy-producing reactions. This paper summarizes the progress made in both areas. Anode materials capable of providing high utilization factors over current densities ranging from 5 to 150 mA/cm 2 have been identified, such materials being essential to realize mission life for the UUV. With respect to the electrolyte management system, a filter/precipitator unit has been successfully operated for over 250 h in a large scale, half-cell system.

  4. Corneal healing after riboflavin ultraviolet-A collagen cross-linking determined by confocal laser scanning microscopy in vivo: early and late modifications.

    Science.gov (United States)

    Mazzotta, Cosimo; Traversi, Claudio; Baiocchi, Stefano; Caporossi, Orsola; Bovone, Cristina; Sparano, Maria Caterina; Balestrazzi, Angelo; Caporossi, Aldo

    2008-10-01

    To assess early and late micromorphological modifications of cross-linked corneas in vivo by means of Heidelberg Retinal Tomography (HRT) II confocal microscopy. Prospective nonrandomized open trial. Micromorphological examination of 44 cross-linked keratoconic corneas was performed in vivo by HRT II confocal laser scanning microscopy. Riboflavin ultraviolet (UV)-A-induced corneal collagen cross-linking (CXL) was performed according to the Siena protocol: pilocarpin 1% drops 30 minutes before, topical anesthesia with lidocaine 4% drops 15 minutes before irradiation, mechanical scraping of epithelium (9-mm-diameter area), preirradiation soaking for 10 minutes in riboflavin solution 0.1% (Ricrolin, Sooft, Italy) applied every 2.5 minutes for 30 minutes, 30 minutes exposure to solid-state UVA illuminator (Caporossi; Baiocchi; Mazzotta, X-linker, CSO, Italy), 8-mm-diameter irradiated area, energy delivered 3 mW/cm(2). All patients were examined by confocal scans preoperatively and at the following times after treatment: one, three, and six months, and one, two, and three years. No damage to the limbal region was observed. Epithelial regrowth was complete after four days of soft contact lens bandage. The anatomy of the subepithelial plexus was restored one year after the operation with full corneal sensitivity. Increased density of extracellular matrix in late postoperative period indicated cross-linked collagen to a depth of 340 microm expressed by a late demarcation line. In vivo confocal microscopy showed early and late modification of corneal microstructure after the treatment. The three-year stability of CXL recorded could be related to increased cross-links formation, synthesis of well-structured collagen and new lamellar interconnections.

  5. Characterization and in vitro and in vivo evaluation of cross-linked chitosan films as implant for controlled release of citalopram

    Indian Academy of Sciences (India)

    Patit P Kundu; Santosh Kumar Jindal; Manish Goswami

    2013-02-01

    The aim of the present study is to develop cross-linked chitosan (CH) films that can release drug over an extended period of time and that too in a controlled manner. A solution of different percentages of CH, is prepared in 1% lactic acid, followed by addition of citalopram (CTP) and then reacted with increasing amounts of glutaraldehyde (GL) to obtain films with different cross-linking densities. Prepared films are characterized for their physical and mechanical properties. The films are then subjected to in vitro drug release studies using pH 7.4 phosphate buffer saline (PBS) as dissolution medium and cumulative amount of drug released is calculated. Kinetic analysis of drug release is performed using Power law model and Higuchi’s model.With increase in concentration of CH, water absorption capacity and mechanical strength are increased; whereas, water vapour permeability and elasticity of the films are decreased. The effect of cross-linking agent, GL, is such that with an increase in the amount of GL, water vapour permeability, water absorption capacity and elasticity of the films are decreased; whereas, mechanical strength increased to some extent and then decreased. In vitro release studies indicate that films containing 3% CH, cross-linked with 2–3% GL and films containing 4%CH, cross-linked 1%GL are able to sustain the drug release for a prolonged time along with releasing almost complete drug in a desired period. Out of these batches, films containing 3% CH, cross-linked with 2–3% GL are having sufficient strength, water vapour permeation, water absorption capacity and elongation at break for implantation purpose. The in vitro degradation studies and histopathological studies were carried out with a sample film (batch C3 as in table 1) in rabbit model. In vitro degradation study indicates that the films maintained their integrity for desired implantation. The histopathological studies under optical microscope indicates that on implanting, there is no

  6. Preparation of cross-linked hen-egg white lysozyme crystals free of cracks

    Science.gov (United States)

    Yan, Er-Kai; Lu, Qin-Qin; Zhang, Chen-Yan; Liu, Ya-Li; He, Jin; Chen, Da; Wang, Bo; Zhou, Ren-Bin; Wu, Ping; Yin, Da-Chuan

    2016-01-01

    Cross-linked protein crystals (CLPCs) are very useful materials in applications such as biosensors, catalysis, and X-ray crystallography. Hence, preparation of CLPCs is an important research direction. During the preparation of CLPCs, an often encountered problem is that cracks may appear in the crystals, which may finally lead to shattering of the crystals into small pieces and cause problem in practical applications. To avoid cross-link induced cracking, it is necessary to study the cracking phenomenon in the preparation process. In this paper, we present an investigation on how to avoid cracking during preparation of CLPCs. An orthogonal experiment was designed to study the phenomenon of cross-link induced cracking of hen-egg white lysozyme (HEWL) crystals against five parameters (temperature, solution pH, crystal growth time, glutaraldehyde concentration, and cross-linking time). The experimental results showed that, the solution pH and crystal growth time can significantly affect cross-link induced cracking. The possible mechanism was studied, and optimized conditions for obtaining crack-free CLPCs were obtained and experimentally verified. PMID:27703210

  7. Incorporation of Decanethiol-Passivated Gold Nanoparticles into Cross-Linked Poly(Dimethylsiloxane Films

    Directory of Open Access Journals (Sweden)

    Motohiro Tagaya

    2011-01-01

    Full Text Available Cross-linking degree of a poly(dimethylsiloxane (PDMS film was controlled, and the incorporation of hydrophobic decanethiol-passivated gold (Au nanoparticles into the film was investigated. FT-IR spectra indicated that the hydrosilylation reaction between a vinyl group and a hydrosilyl group occurred with the cross-linking. The swelling degree of the film in toluene changed with a cross-linker concentration, indicating the control of the cross-linking degree of PDMS film. By EDX analysis, the amount of incorporated Au nanoparticles increased with decreasing a cross-linker concentration, indicating the enlarged free volume of the film. The Au nanoparticle-PDMS composite film containing a cross-linker at 6 wt% showed brown color attributed to plasmon resonance of Au nanoparticles, suggesting the Au nanoparticles in the film at monodispersion state. The UV-visible absorbance of the composite film decreased without spectralshift by swelling with toluene, and the changes were reversible. The aggregation among Au nanoparticles in the composite film after calcination also depended on the cross-linking degree. Thus, the control of cross-linking degree of PDMS film successfully leaded to a simple way of fabricating the Au nanoparticle-PDMS composite film at the mono-dispersion state.

  8. Mapping of the dimer interface of the Escherichia coli mannitol permease by cysteine cross-linking.

    Science.gov (United States)

    van Montfort, Bart A; Schuurman-Wolters, Gea K; Wind, Joyce; Broos, Jaap; Robillard, George T; Poolman, Bert

    2002-04-26

    A cysteine cross-linking approach was used to identify residues at the dimer interface of the Escherichia coli mannitol permease. This transport protein comprises two cytoplasmic domains and one membrane-embedded C domain per monomer, of which the latter provides the dimer contacts. A series of single-cysteine His-tagged C domains present in the native membrane were subjected to Cu(II)-(1,10-phenanthroline)(3)-catalyzed disulfide formation or cysteine cross-linking with dimaleimides of different length. The engineered cysteines were at the borders of the predicted membrane-spanning alpha-helices. Two residues were found to be located in close proximity of each other and capable of forming a disulfide, while four other locations formed cross-links with the longer dimaleimides. Solubilization of the membranes did only influence the cross-linking behavior at one position (Cys(73)). Mannitol binding only effected the cross-linking of a cysteine at the border of the third transmembrane helix (Cys(134)), indicating that substrate binding does not lead to large rearrangements in the helix packing or to dissociation of the dimer. Upon mannitol binding, the Cys(134) becomes more exposed but the residue is no longer capable of forming a stable disulfide in the dimeric IIC domain. In combination with the recently obtained projection structure of the IIC domain in two-dimensional crystals, a first proposal is made for alpha-helix packing in the mannitol permease.

  9. Site specificity of psoralen-DNA interstrand cross-linking determined by nuclease Bal31 digestion

    DEFF Research Database (Denmark)

    Zhen, W P; Buchardt, O; Nielsen, Henrik

    1986-01-01

    A novel method for determination of psoralen photo-cross-linking sites in double-stranded DNA is described, which is based on a pronounced inhibition of Bal31 exonuclease activity by psoralen-DNA interstrand cross-links. The results using a 51 base pair fragment of plasmid pUC19 and a 346 base pair...... fragment of pBR322 show that 5'-TA sequences are preferred cross-linking sites compared to 3'-TA sequences. They also indicate that sequences flanking the 5'-TA site influence the cross-linking efficiency at the site. The DNA photo-cross-linking by 4,5',8-trimethylpsoralen and 8-methoxypsoralen...... was analyzed, and these two psoralens showed identical site specificity. The 5'-TA preference is rationalized on the basis of the local DNA structure in terms of the pi-pi electronic interaction between the thymines and the intercalated psoralens, as well as on the base tilt angles of the DNA....

  10. A General Method for Targeted Quantitative Cross-Linking Mass Spectrometry

    Science.gov (United States)

    Chavez, Juan D.; Eng, Jimmy K.; Schweppe, Devin K.; Cilia, Michelle; Rivera, Keith; Zhong, Xuefei; Wu, Xia; Allen, Terrence; Khurgel, Moshe; Kumar, Akhilesh; Lampropoulos, Athanasios; Larsson, Mårten; Maity, Shuvadeep; Morozov, Yaroslav; Pathmasiri, Wimal; Perez-Neut, Mathew; Pineyro-Ruiz, Coriness; Polina, Elizabeth; Post, Stephanie; Rider, Mark; Tokmina-Roszyk, Dorota; Tyson, Katherine; Vieira Parrine Sant'Ana, Debora; Bruce, James E.

    2016-01-01

    Chemical cross-linking mass spectrometry (XL-MS) provides protein structural information by identifying covalently linked proximal amino acid residues on protein surfaces. The information gained by this technique is complementary to other structural biology methods such as x-ray crystallography, NMR and cryo-electron microscopy[1]. The extension of traditional quantitative proteomics methods with chemical cross-linking can provide information on the structural dynamics of protein structures and protein complexes. The identification and quantitation of cross-linked peptides remains challenging for the general community, requiring specialized expertise ultimately limiting more widespread adoption of the technique. We describe a general method for targeted quantitative mass spectrometric analysis of cross-linked peptide pairs. We report the adaptation of the widely used, open source software package Skyline, for the analysis of quantitative XL-MS data as a means for data analysis and sharing of methods. We demonstrate the utility and robustness of the method with a cross-laboratory study and present data that is supported by and validates previously published data on quantified cross-linked peptide pairs. This advance provides an easy to use resource so that any lab with access to a LC-MS system capable of performing targeted quantitative analysis can quickly and accurately measure dynamic changes in protein structure and protein interactions. PMID:27997545

  11. Ice templated and cross-linked xylan/nanocrystalline cellulose hydrogels.

    Science.gov (United States)

    Köhnke, Tobias; Elder, Thomas; Theliander, Hans; Ragauskas, Arthur J

    2014-01-16

    Structured xylan-based hydrogels, reinforced with cellulose nanocrystals (CNCs), have successfully been prepared from water suspensions by cross-linking during freeze-casting. In order to induce cross-linking during the solidification/sublimation operation, xylan was first oxidized using sodium periodate to introduce dialdehydes. The oxidized xylan was then mixed with CNCs after which the suspension was frozen unidirectionally in order to control the ice crystal formation and by that the pore morphology of the material. Finally the ice crystal templates were removed by freeze-drying. During the freeze-casting process hemiacetal bonds are formed between the aldehyde groups and hydroxyl groups, either on other xylan molecules or on CNCs, which cross-links the system. The proposed cross-linking reaction was confirmed by using cross-polarization magic angle spinning (CP/MAS) nuclear magnetic resonance (NMR) spectroscopy. The pore morphology of the obtained materials was analyzed by scanning electron microscopy (SEM). The materials were also tested for compressive strength properties, both in dry and water swollen state. All together this study describes a novel combined freeze-casting/cross-linking process which enables fabrication of nanoreinforced biopolymer-based hydrogels with controlled porosity and 3-D architecture.

  12. Studies on Cross-linking of succinic acid with chitosan/collagen

    Directory of Open Access Journals (Sweden)

    Tapas Mitra

    2013-01-01

    Full Text Available The present study summarizes the cross-linking property of succinic acid with chitosan /collagen. In detail, the chemistry behind the cross-linking and the improvement in mechanical and thermal properties of the cross-linked material were discussed with suitable instruments and bioinformatics tools. The concentration of succinic acid with reference to the chosen polymers was optimized. A 3D scaffold prepared using an optimized concentration of succinic acid (0.2% (w/v with chitosan (1.0% (w/v and similarly with collagen (0.5% (w/v, was subjected to surface morphology, FT-IR analysis, tensile strength assessment, thermal stability and biocompatibility. Results revealed, cross-linking with succinic acid impart appreciable mechanical strength to the scaffold material. In silico analysis suggested the prevalence of non-covalent interactions, which played a crucial role in improving the mechanical and thermal properties of the cross-linked scaffold. The resultant 3D scaffold may find application as wound dressing material, as an implant in clinical applications and as a tissue engineering material.

  13. Mechanical and biocompatible characterization of a cross-linked collagen-hyaluronic acid wound dressing.

    Science.gov (United States)

    Kirk, James F; Ritter, Gregg; Finger, Isaac; Sankar, Dhyana; Reddy, Joseph D; Talton, James D; Nataraj, Chandra; Narisawa, Sonoko; Millán, José Luis; Cobb, Ronald R

    2013-01-01

    Collagen scaffolds have been widely employed as a dermal equivalent to induce fibroblast infiltrations and dermal regeneration in the treatment of chronic wounds and diabetic foot ulcers. Cross-linking methods have been developed to address the disadvantages of the rapid degradation associated with collagen-based scaffolds. To eliminate the potential drawbacks associated with glutaraldehyde cross-linking, methods using a water soluble carbodiimide have been developed. In the present study, the glycosaminoglycan (GAG) hyaluronic acid (HA), was covalently attached to an equine tendon derived collagen scaffold using 1-ethyl-3-(3-dimethyl aminopropyl) carbodiimide (EDC) to create ntSPONGE The HA was shown to be homogeneously distributed throughout the collagen matrix. In vitro analyses of the scaffold indicated that the cross-linking enhanced the biological stability by decreasing the enzymatic degradation and increasing the thermal denaturation temperature. The material was shown to support the attachment and proliferation of mouse L929 fibroblast cells. In addition, the cross-linking decreased the resorption rate of the collagen as measured in an intramuscular implant model in rabbits. The material was also shown to be biocompatible in a variety of in vitro and in vivo assays. These results indicate that this cross-linked collagen-HA scaffold, ntSPONGE has the potential for use in chronic wound healing.

  14. Novel Technique of Transepithelial Corneal Cross-Linking Using Iontophoresis in Progressive Keratoconus

    Science.gov (United States)

    Raffa, Paolo; Rosati, Marianna

    2016-01-01

    In this work, the authors presented the techniques and the preliminary results at 6 months of a randomized controlled trial (NCT02117999) comparing a novel transepithelial corneal cross-linking protocol using iontophoresis with the Dresden protocol for the treatment of progressive keratoconus. At 6 months, there was a significant average improvement with an average flattening of the maximum simulated keratometry reading of 0.72 ± 1.20 D (P = 0.01); in addition, corrected distance visual acuity improved significantly (P = 0.08) and spherical equivalent refraction was significantly less myopic (P = 0.02) 6 months after transepithelial corneal cross-linking with iontophoresis. The novel protocol using iontophoresis showed comparable results with standard corneal cross-linking to halt progression of keratoconus during 6-month follow-up. Investigation of the long-term RCT outcomes are ongoing to verify the efficacy of this transepithelial corneal cross-linking protocol and to determine if it may be comparable with standard corneal cross-linking in the management of progressive keratoconus. PMID:27597895

  15. Novel Technique of Transepithelial Corneal Cross-Linking Using Iontophoresis in Progressive Keratoconus

    Directory of Open Access Journals (Sweden)

    Marco Lombardo

    2016-01-01

    Full Text Available In this work, the authors presented the techniques and the preliminary results at 6 months of a randomized controlled trial (NCT02117999 comparing a novel transepithelial corneal cross-linking protocol using iontophoresis with the Dresden protocol for the treatment of progressive keratoconus. At 6 months, there was a significant average improvement with an average flattening of the maximum simulated keratometry reading of 0.72±1.20 D (P=0.01; in addition, corrected distance visual acuity improved significantly (P=0.08 and spherical equivalent refraction was significantly less myopic (P=0.02 6 months after transepithelial corneal cross-linking with iontophoresis. The novel protocol using iontophoresis showed comparable results with standard corneal cross-linking to halt progression of keratoconus during 6-month follow-up. Investigation of the long-term RCT outcomes are ongoing to verify the efficacy of this transepithelial corneal cross-linking protocol and to determine if it may be comparable with standard corneal cross-linking in the management of progressive keratoconus.

  16. DNA interstrand cross-link induced by estrogens as well as their complete and synergic carcinogenesis

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The estrogens show negative activity in Ames test, but estrodiol and diethylstilbestrol in estrogens both are carcinogens based upon animal experiments and epidemiological investigation. It is concluded from the di-region theory, a mechanism conception put forward by one of the present authors, that the carcinogenesis of estrogens is switched on by the covalent cross-link between complementary DNA bases induced by them. We verified for the first time by the DNA alkaline elution method that both estrodiol and diethylstilbestrol cause covalent cross-link between DNA-protein and DNA interstrands after metabolic activation with dosage correlation, but neither the non-carcinogens cholesterol nor pyrene can lead to these sorts of cross-link in the same condition. It has been known that there is a synergetic effect between estrogen and pollution of polycyclic aromatic hydrocarbons. Although non-carcinogenic pyrene alone cannot induce cross-link, its addition with equal molar quantity to estrodiol culture causes synergically the total and DNA interstrand cross-link ratios to be respectively four and three times more than the ones in the cultivation with estrodiol only. It is shown that not only the estrodiol set off the formation of pyrene bi-radicals, but also the pyrene radicals arouse conversely the production of estrodiol bi-radicals.

  17. Cross-linked Composite Gel Polymer Electrolyte using Mesoporous Methacrylate-Functionalized SiO2 Nanoparticles for Lithium-Ion Polymer Batteries

    Science.gov (United States)

    Shin, Won-Kyung; Cho, Jinhyun; Kannan, Aravindaraj G.; Lee, Yoon-Sung; Kim, Dong-Won

    2016-05-01

    Liquid electrolytes composed of lithium salt in a mixture of organic solvents have been widely used for lithium-ion batteries. However, the high flammability of the organic solvents can lead to thermal runaway and explosions if the system is accidentally subjected to a short circuit or experiences local overheating. In this work, a cross-linked composite gel polymer electrolyte was prepared and applied to lithium-ion polymer cells as a safer and more reliable electrolyte. Mesoporous SiO2 nanoparticles containing reactive methacrylate groups as cross-linking sites were synthesized and dispersed into the fibrous polyacrylonitrile membrane. They directly reacted with gel electrolyte precursors containing tri(ethylene glycol) diacrylate, resulting in the formation of a cross-linked composite gel polymer electrolyte with high ionic conductivity and favorable interfacial characteristics. The mesoporous SiO2 particles also served as HF scavengers to reduce the HF content in the electrolyte at high temperature. As a result, the cycling performance of the lithium-ion polymer cells with cross-linked composite gel polymer electrolytes employing methacrylate-functionalized mesoporous SiO2 nanoparticles was remarkably improved at elevated temperatures.

  18. Cross-linked Composite Gel Polymer Electrolyte using Mesoporous Methacrylate-Functionalized SiO2 Nanoparticles for Lithium-Ion Polymer Batteries.

    Science.gov (United States)

    Shin, Won-Kyung; Cho, Jinhyun; Kannan, Aravindaraj G; Lee, Yoon-Sung; Kim, Dong-Won

    2016-05-18

    Liquid electrolytes composed of lithium salt in a mixture of organic solvents have been widely used for lithium-ion batteries. However, the high flammability of the organic solvents can lead to thermal runaway and explosions if the system is accidentally subjected to a short circuit or experiences local overheating. In this work, a cross-linked composite gel polymer electrolyte was prepared and applied to lithium-ion polymer cells as a safer and more reliable electrolyte. Mesoporous SiO2 nanoparticles containing reactive methacrylate groups as cross-linking sites were synthesized and dispersed into the fibrous polyacrylonitrile membrane. They directly reacted with gel electrolyte precursors containing tri(ethylene glycol) diacrylate, resulting in the formation of a cross-linked composite gel polymer electrolyte with high ionic conductivity and favorable interfacial characteristics. The mesoporous SiO2 particles also served as HF scavengers to reduce the HF content in the electrolyte at high temperature. As a result, the cycling performance of the lithium-ion polymer cells with cross-linked composite gel polymer electrolytes employing methacrylate-functionalized mesoporous SiO2 nanoparticles was remarkably improved at elevated temperatures.

  19. Cross-linked Composite Gel Polymer Electrolyte using Mesoporous Methacrylate-Functionalized SiO2 Nanoparticles for Lithium-Ion Polymer Batteries

    Science.gov (United States)

    Shin, Won-Kyung; Cho, Jinhyun; Kannan, Aravindaraj G.; Lee, Yoon-Sung; Kim, Dong-Won

    2016-01-01

    Liquid electrolytes composed of lithium salt in a mixture of organic solvents have been widely used for lithium-ion batteries. However, the high flammability of the organic solvents can lead to thermal runaway and explosions if the system is accidentally subjected to a short circuit or experiences local overheating. In this work, a cross-linked composite gel polymer electrolyte was prepared and applied to lithium-ion polymer cells as a safer and more reliable electrolyte. Mesoporous SiO2 nanoparticles containing reactive methacrylate groups as cross-linking sites were synthesized and dispersed into the fibrous polyacrylonitrile membrane. They directly reacted with gel electrolyte precursors containing tri(ethylene glycol) diacrylate, resulting in the formation of a cross-linked composite gel polymer electrolyte with high ionic conductivity and favorable interfacial characteristics. The mesoporous SiO2 particles also served as HF scavengers to reduce the HF content in the electrolyte at high temperature. As a result, the cycling performance of the lithium-ion polymer cells with cross-linked composite gel polymer electrolytes employing methacrylate-functionalized mesoporous SiO2 nanoparticles was remarkably improved at elevated temperatures. PMID:27189842

  20. Effects of cross-linking molecular weights in a hyaluronic acid-poly(ethylene oxide) hydrogel network on its properties

    Energy Technology Data Exchange (ETDEWEB)

    Noh, Insup [Department of Chemical Engineering, Seoul National University of Technology, 172 Gongnung-dong, Nowon-gu, Seoul 139-743 (Korea, Republic of); Kim, Gun-Woo [Department of Chemical Engineering, Seoul National University of Tech