WorldWideScience

Sample records for high concentration brines

  1. Purification of High Salinity Brine by Multi-Stage Ion Concentration Polarization Desalination

    Science.gov (United States)

    Kim, Bumjoo; Kwak, Rhokyun; Kwon, Hyukjin J.; Pham, Van Sang; Kim, Minseok; Al-Anzi, Bader; Lim, Geunbae; Han, Jongyoon

    2016-01-01

    There is an increasing need for the desalination of high concentration brine (>TDS 35,000 ppm) efficiently and economically, either for the treatment of produced water from shale gas/oil development, or minimizing the environmental impact of brine from existing desalination plants. Yet, reverse osmosis (RO), which is the most widely used for desalination currently, is not practical for brine desalination. This paper demonstrates technical and economic feasibility of ICP (Ion Concentration Polarization) electrical desalination for the high saline water treatment, by adopting multi-stage operation with better energy efficiency. Optimized multi-staging configurations, dependent on the brine salinity values, can be designed based on experimental and numerical analysis. Such an optimization aims at achieving not just the energy efficiency but also (membrane) area efficiency, lowering the true cost of brine treatment. ICP electrical desalination is shown here to treat brine salinity up to 100,000 ppm of Total Dissolved Solids (TDS) with flexible salt rejection rate up to 70% which is promising in a various application treating brine waste. We also demonstrate that ICP desalination has advantage of removing both salts and diverse suspended solids simultaneously, and less susceptibility to membrane fouling/scaling, which is a significant challenge in the membrane processes. PMID:27545955

  2. Purification of High Salinity Brine by Multi-Stage Ion Concentration Polarization Desalination

    Science.gov (United States)

    Kim, Bumjoo; Kwak, Rhokyun; Kwon, Hyukjin J.; Pham, Van Sang; Kim, Minseok; Al-Anzi, Bader; Lim, Geunbae; Han, Jongyoon

    2016-08-01

    There is an increasing need for the desalination of high concentration brine (>TDS 35,000 ppm) efficiently and economically, either for the treatment of produced water from shale gas/oil development, or minimizing the environmental impact of brine from existing desalination plants. Yet, reverse osmosis (RO), which is the most widely used for desalination currently, is not practical for brine desalination. This paper demonstrates technical and economic feasibility of ICP (Ion Concentration Polarization) electrical desalination for the high saline water treatment, by adopting multi-stage operation with better energy efficiency. Optimized multi-staging configurations, dependent on the brine salinity values, can be designed based on experimental and numerical analysis. Such an optimization aims at achieving not just the energy efficiency but also (membrane) area efficiency, lowering the true cost of brine treatment. ICP electrical desalination is shown here to treat brine salinity up to 100,000 ppm of Total Dissolved Solids (TDS) with flexible salt rejection rate up to 70% which is promising in a various application treating brine waste. We also demonstrate that ICP desalination has advantage of removing both salts and diverse suspended solids simultaneously, and less susceptibility to membrane fouling/scaling, which is a significant challenge in the membrane processes.

  3. Purification of High Salinity Brine by Multi-Stage Ion Concentration Polarization Desalination.

    Science.gov (United States)

    Kim, Bumjoo; Kwak, Rhokyun; Kwon, Hyukjin J; Pham, Van Sang; Kim, Minseok; Al-Anzi, Bader; Lim, Geunbae; Han, Jongyoon

    2016-08-22

    There is an increasing need for the desalination of high concentration brine (>TDS 35,000 ppm) efficiently and economically, either for the treatment of produced water from shale gas/oil development, or minimizing the environmental impact of brine from existing desalination plants. Yet, reverse osmosis (RO), which is the most widely used for desalination currently, is not practical for brine desalination. This paper demonstrates technical and economic feasibility of ICP (Ion Concentration Polarization) electrical desalination for the high saline water treatment, by adopting multi-stage operation with better energy efficiency. Optimized multi-staging configurations, dependent on the brine salinity values, can be designed based on experimental and numerical analysis. Such an optimization aims at achieving not just the energy efficiency but also (membrane) area efficiency, lowering the true cost of brine treatment. ICP electrical desalination is shown here to treat brine salinity up to 100,000 ppm of Total Dissolved Solids (TDS) with flexible salt rejection rate up to 70% which is promising in a various application treating brine waste. We also demonstrate that ICP desalination has advantage of removing both salts and diverse suspended solids simultaneously, and less susceptibility to membrane fouling/scaling, which is a significant challenge in the membrane processes.

  4. Steric stabilization of nanoparticles with grafted low molecular weight ligands in highly concentrated brines including divalent ions.

    Science.gov (United States)

    Worthen, Andrew J; Tran, Vu; Cornell, Kevin A; Truskett, Thomas M; Johnston, Keith P

    2016-02-21

    Whereas numerous studies of stabilization of nanoparticles (NPs) in electrolytes have examined biological fluids, the interest has grown recently in media with much higher ionic strengths including seawater and brines relevant to environmental science and subsurface oil and gas reservoirs. Given that electrostatic repulsion is limited at extremely high ionic strengths due to charge screening, we have identified ligands that are well solvated in concentrated brine containing divalent cations and thus provide steric stabilization of silica nanoparticles. Specifically, the hydrodynamic diameter of silica nanoparticles with grafted low molecular weight ligands, a diol ether, [3-(2,3-dihydroxypropoxy)propyl]-trimethoxysilane, and a zwitterionic sulfobetaine, 3-([dimethyl(3-trimethoxysilyl)propyl]ammonio)propane-1-sulfonate, is shown with dynamic light scattering to remain essentially constant, indicating lack of aggregation, at room temperature and up to 80 °C for over 30 days. An extended DLVO model signifies that steric stabilization is strongly dominant against van der Waals attraction for ∼10 nm particles given that these ligands are well solvated even in highly concentrated brine. In contrast, polyethylene glycol oligomers do not provide steric stabilization at elevated temperatures, even at conditions where the ligands are soluble, indicating complicating factors including bridging of the ether oxygens by divalent cations.

  5. Geochemistry of Aluminum in High Temperature Brines

    Energy Technology Data Exchange (ETDEWEB)

    Benezeth, P.; Palmer, D.A.; Wesolowski, D.J.

    1999-05-18

    The objective ofthis research is to provide quantitative data on the equilibrium and thermodynamic properties of aluminum minerals required to model changes in permeability and brine chemistry associated with fluid/rock interactions in the recharge, reservoir, and discharge zones of active geothermal systems. This requires a precise knowledge of the thermodynamics and speciation of aluminum in aqueous brines, spanning the temperature and fluid composition rangesencountered in active systems. The empirical and semi-empirical treatments of the solubility/hydrolysis experimental results on single aluminum mineral phases form the basis for the ultimate investigation of the behavior of complex aluminosilicate minerals. The principal objective in FY 1998 was to complete the solubility measurements on boehmite (AIOOH) inNaC1 media( 1 .O and 5.0 molal ionic strength, IOO-250°C). However, additional measurements were also made on boehmite solubility in pure NaOH solutions in order to bolster the database for fitting in-house isopiestic data on this system. Preliminary kinetic Measurements of the dissolution/precipitation of boehmite was also carried out, although these were also not planned in the earlier objective. The 1999 objectives are to incorporate these treatments into existing codes used by the geothermal industry to predict the chemistry ofthe reservoirs; these calculations will be tested for reliability against our laboratory results and field observations. Moreover, based on the success of the experimental methods developed in this program, we intend to use our unique high temperature pH easurement capabilities to make kinetic and equilibrium studies of pH-dependent aluminosilicate transformation reactions and other pH-dependent heterogeneous reactions.

  6. Prospects of the complex development of highly parameter geothermal brines

    Science.gov (United States)

    Alkhasov, A. B.; Alkhasova, D. A.; Ramazanov, A. Sh.; Kasparova, M. A.

    2015-06-01

    The high efficiency of complex processing of high-temperature hydrothermal brines with utilization of heat energy in a binary geothermal power plant and subsequent extraction of solved chemical compounds is shown. Promising technological schemes are given, where electric power, which is generated in the binary geothermal power plant, is used in a block to recover chemistry components. The technology for integrated processing of geothermal brines of the chloride-sodium-calcium type is developed, which provides the manufacture not only of marketable products but also of practically overall reagents of processed water that are necessary to realize the technology. Priority areas for development are indicated, and the preliminary estimates for a Berikey geothermal deposit are given. It is shown that only established resources of thermal brines of the Berikey deposit make it possible to produce more than 2000 t of lithium carbonate and, thereby, to completely provide Russian industry requirements for it.

  7. An aqueous thermodynamic model for the Pb 2+-Na +-K +-Ca 2+-Mg 2+-H +-Cl --SO 42--H 2O system to high concentration: application to WIPP brines

    Science.gov (United States)

    Felmy, Andrew R.; Onishi, Lisa M.; Foster, Nancy S.; Rustad, James R.; Rai, Dhanpat; Mason, Marvin J.

    2000-11-01

    The development of an aqueous thermodynamic model for the Pb 2+-Na +-K +-Ca 2+-Mg 2+-Cl --SO 42--H 2O system is presented, which is valid to high ionic strengths at 25°C. The model is based on the equations of Pitzer and has been parameterized from existing solubility, osmotic, electromotive force (emf), and spectroscopic data. To accurately represent the aqueous thermodynamics of Pb 2+ in concentrated chloride containing solutions required the inclusion of four Pb chloride species (i.e., PbCl +, PbCl 2(aq), PbCl 3-, and PbCl 42-) along with the necessary Pitzer ion interaction parameters for these species with the major electrolyte ions. The reliability of the final equilibrium model is tested against experimental solubility data on PbCl 2(c) and PbSO 4(c) in high ionic strength Waste Isolation Pilot Plant (WIPP) brines obtained as part of this study. On an overall basis the model accurately predicted the aqueous speciation, based on comparisons with our UV-Vis spectroscopy measurements, as well as the observed solubility. The model also proved satisfactory in predicting the observed solid phase assemblages, with the possible exception of those found in solutions high in KCl.

  8. Distinctive Microbial Community Structure in Highly Stratified Deep-Sea Brine Water Columns

    KAUST Repository

    Bougouffa, Salim

    2013-03-29

    Atlantis II and Discovery are two hydrothermal and hypersaline deep-sea pools in the Red Sea rift that are characterized by strong thermohalo-stratification and temperatures steadily peaking near the bottom. We conducted comprehensive vertical profiling of the microbial populations in both pools and highlighted the influential environmental factors. Pyrosequencing of the 16S rRNA genes revealed shifts in community structures vis-à-vis depth. High diversity and low abundance were features of the deepest convective layers despite the low cell density. Surprisingly, the brine interfaces had significantly higher cell counts than the overlying deep-sea water, yet they were lowest in diversity. Vertical stratification of the bacterial populations was apparent as we moved from the Alphaproteobacteria-dominated deep sea to the Planctomycetaceae- or Deferribacteres-dominated interfaces to the Gammaproteobacteria-dominated brine layers. Archaeal marine group I was dominant in the deep-sea water and interfaces, while several euryarchaeotic groups increased in the brine. Across sites, microbial phylotypes and abundances varied substantially in the brine interface of Discovery compared with Atlantis II, despite the near-identical populations in the overlying deep-sea waters. The lowest convective layers harbored interestingly similar microbial communities, even though temperature and heavy metal concentrations were very different. Multivariate analysis indicated that temperature and salinity were the major influences shaping the communities. The harsh conditions and the low-abundance phylotypes could explain the observed correlation in the brine pools.

  9. 盐田高浓度卤水蒸发的数学模型 及动力学研究%Theoretical Model and Dynamics Study of Highly Concentrated Brine Evaporation in Solar Pond

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    This paper is the first to treat the solar pond system as a special kind of chemical reactor and separation equipment in the light of theory of chemical engineering and has discussion on it in detail. Based on a great number of experimental data carried out outside field, the paper analyses and studies systematically the parameters of dynamics of brine of the quaternary system Na+,K+,Mg2+∥Cl--H2O during the evaporation period from the stage of sodium chloride to the stage of bischofite, and then analyses all the parameters theoretically and make some proper assumption that is proved by analysis of field data to deduce a theoretical relation of evaporation dynamic of highly concentrated brine in solar ponds, finally the paper develops a actual experimental model that describes the evaporation of the brine of the system of Na+,K+,Mg2+∥Cl--H2O.  The experimental model can be changed simply into an other form that can be effectively used in the design and management of solar ponds system production. The paper also discusses some way of using the experimental model in a computer automatic management system of solar ponds in the production in the industry in future. By analyzing all the experimental data tested in the outside field and the meteorological data, also the paper deals with the some relationship of the parameters above and give a result that will be significant for the effective.%首次从化学工程的角度,将盐田系统作为一类特殊的化学反应器和无机盐分离设备进行了详细的论述。在大量试验基础上,系统地分析和研究了Na+,K+,Mg2+∥Cl-,-H2O四元水盐体系卤水在天然蒸发状态下的宏观蒸发动力学参数。从理论上对与卤水蒸发相关的多种参数进行了分析和合理简化,概述了卤水蒸发过程中的质量传递规律。并在此基础上通过计算机模拟方法建立了四元水盐体系高浓度卤水在特定地域中进行天然蒸发的卤水宏观蒸发动力学

  10. Diverse methane concentrations in anoxic brines and underlying sediments, eastern Mediterranean Sea

    Digital Repository Service at National Institute of Oceanography (India)

    Karisiddaiah, S.M.

    Elevated methane (CH sub(4)) concentrations (128-2692x10 sup(3) nM) occur in the hypersaline anoxic brine pools of Bannock and Urania Basins, eastern Mediterranean Sea, compared to low concentrations (17-80x10 sup(3) nM) in the sediments below...

  11. Stabilization of high mercury contaminated brine purification sludge.

    Science.gov (United States)

    Zhuang, J Ming; Lo, Tony; Walsh, Tony; Lam, Tak

    2004-09-10

    The highly leachable mercury contaminants of brine purification sludge (BPS) generated from the Hg-cell electrolysis process in chlorine production can be stabilized in the treatment procedure employing ferric-lignin derivatives (FLD) (Ligmet binder) and Portland cement (PC). The stabilization effectiveness has been examined by time-based multiple toxicity characteristic leaching procedure (TCLP) tests and sequential TCLP tests. In a period of 50 days, the multiple TCLP tests showed a variation of less than 90 microg l(-1) for the leachable mercury level, and the sequential TCLP tests for the same sample displayed a declining TCLP mercury level. Based on this study, the stabilization of approximately 2000 t of brine purification sludge has been successfully processed with the ferric-lignin derivatives treatment.

  12. Extraction of rubidium from the concentrated brine rejected by integrated nuclear desalination systems

    Energy Technology Data Exchange (ETDEWEB)

    Nisan, S.; Laffore, F. [CEA Cadarache, DEN DER SESI, 13 - Saint Paul lez Durance (France); Poletiko, C.; Simon, N. [CEA Cadarache, DTN STPA LPC, 13 - Saint Paul lez Durance (France)

    2009-07-01

    Rubidium is one of the elements present in the concentrated brine rejected by desalination systems. In view of the potentially high price of the pore metal, it is worthwhile to investigate its extraction, even though presently the available Rb resources are adequate enough to meet the current demands. Two methods have been reported. The first makes use of the ion-exchange resins and the second of the complexation of Rb with specific molecules (calixarenes) followed by one or more nano-filtration/reverse osmosis (NF/RO) stages. First results of calculations indicate that the two methods would be technically very attractive but much experimentation would still be required before an industrial scale extraction process can be evolved. (authors)

  13. Ion association in concentrated NaCl brines from ambient to supercritical conditions: results from classical molecular dynamics simulations

    Directory of Open Access Journals (Sweden)

    Collings Matthew D

    2002-11-01

    Full Text Available Highly concentrated NaCl brines are important geothermal fluids; chloride complexation of metals in such brines increases the solubility of minerals and plays a fundamental role in the genesis of hydrothermal ore deposits. There is experimental evidence that the molecular nature of the NaCl–water system changes over the pressure–temperature range of the Earth's crust. A transition of concentrated NaCl–H2O brines to a "hydrous molten salt" at high P and T has been argued to stabilize an aqueous fluid phase in the deep crust. In this work, we have done molecular dynamic simulations using classical potentials to determine the nature of concentrated (0.5–16 m NaCl–water mixtures under ambient (25°C, 1 bar, hydrothermal (325°C, 1 kbar and deep crustal (625°C, 15 kbar conditions. We used the well-established SPCE model for water together with the Smith and Dang Lennard-Jones potentials for the ions (J. Chem. Phys., 1994, 100, 3757. With increasing temperature at 1 kbar, the dielectric constant of water decreases to give extensive ion-association and the formation of polyatomic (NanClmn-m clusters in addition to simple NaCl ion pairs. Large polyatomic (NanClmn-m clusters resemble what would be expected in a hydrous NaCl melt in which water and NaCl were completely miscible. Although ion association decreases with pressure, temperatures of 625°C are not enough to overcome pressures of 15 kbar; consequently, there is still enhanced Na–Cl association in brines under deep crustal conditions.

  14. Primary proteolysis of white brined goat cheese monitored by high molarity Tris buffer SDS- PAGE system

    National Research Council Canada - National Science Library

    Milenko Smiljanić; Mirjana B. Pešić; Miroljub B. Barać; Sladjana P. Stanojević; Snežana T. Jovanović; Ognjen D. Maćej

    2013-01-01

    The aim of this work was to investigate primary proteolysis of white brined goat cheese prepared from raw milk and to correlate with the results obtained with high-molarity Tris buffer electrophoretic system...

  15. Ion association in natural brines

    Science.gov (United States)

    Truesdell, A.H.; Jones, B.F.

    1969-01-01

    Natural brines, both surface and subsurface, are highly associated aqueous solutions. Ion complexes in brines may be ion pairs in which the cation remains fully hydrated and the bond between the ions is essentially electrostatic, or coordination complexes in which one or more of the hydration water molecules are replaced by covalent bonds to the anion. Except for Cl-, the major simple ions in natural brines form ion pairs; trace and minor metals in brines form mainly coordination complexes. Limitations of the Debye-Hu??ckel relations for activity coefficients and lack of data on definition and stability of all associated species in concentrated solutions tend to produce underestimates of the degree of ion association, except where the brines contain a very high proportion of Cl-. Data and calculations on closed basin brines of highly varied composition have been coupled with electrode measurements of single-ion activities in an attempt to quantify the degree of ion association. Such data emphasize the role of magnesium complexes. Trace metal contents of closed basin brines are related to complexes formed with major anions. Alkaline sulfo- or chlorocarbonate brines (western Great Basin) carry significant trace metal contents apparently as hydroxides or hydroxy polyions. Neutral high chloride brines (Bonneville Basin) are generally deficient in trace metals. With a knowledge of the thermodynamic properties of a natural water, many possible reactions with other phases (solids, gases, other liquids) may be predicted. A knowledge of these reactions is particularly important in the study of natural brines which may be saturated with many solid phases (silicates, carbonates, sulfates, etc.), which may have a high pH and bring about dissolution of other phases (silica, amphoteric hydroxides, CO2, etc.), and which because of their high density may form relatively stable interfaces with dilute waters. ?? 1969.

  16. ANODIC BEHAVIOR OF ALLOY 22 IN HIGH NITRATE BRINES AT TEMPERATURES HIGHER THAN 100C

    Energy Technology Data Exchange (ETDEWEB)

    G.O. LLEVBARE; J.C. ESTILL; A. YILMAZ; R.A. ETIEN; G.A. HUST M.L. STUART

    2006-04-20

    Alloy 22 (N06022) may be susceptible to crevice corrosion in chloride solutions. Nitrate acts as an inhibitor to crevice corrosion. Several papers have been published regarding the effect of nitrate on the corrosion resistance of Alloy 22 at temperatures 100 C and lower. However, very little is known about the behavior of this alloy in highly concentrated brines at temperatures above 100 C. In the current work, electrochemical tests have been carried out to explore the anodic behavior of Alloy 22 in high chloride high nitrate electrolytes at temperatures as high as 160 C at ambient atmospheres. Even though Alloy 22 may adopt corrosion potentials in the order of +0.5 V (in the saturated silver chloride scale), it does not suffer crevice corrosion if there is high nitrate in the solution. That is, the inhibitive effect of nitrate on crevice corrosion is active for temperatures higher than 100 C.

  17. Methodology Measuring Rare Earth Elements in High TDS Reservoir Brines Application as Natural Tracers in CCUS Studies

    Science.gov (United States)

    Smith, W.; Mcling, T. L.; Smith, R. W.; Neupane, H.

    2013-12-01

    In recent years rare earth elements (REE) have been demonstrated to be useful natural tracers for geochemical processes in aqueous environments. The application of REE's to carbon dioxide utilization and storage (CCUS) could provide researchers with a sensitive, inexpensive tool for tracking the movement of CO2 and displaced formation brines. By definition, geologic reservoirs that have been deemed suitable for carbon capture and storage contain formation brine with total dissolved solids (TDS) greater than 10,000 ppm and often these formation brines exceed 75,000 ppm TDS. This high TDS water makes it very difficult to measure REE, which typically occur at part per trillion concentrations. Critical to the use of REE for CCUS studies is the development of a procedure, which allows for the pre-concentration of REE's across a wide range of water quality. Additionally, due to the large number of samples that will need analysis, any developed procedure must be inexpensive, reproducible, and quick to implement. As part of the Big Sky Carbon Sequestration Project the INL's Center for Advance Energy Studies is developing REE pre-concentration procedures based on methods reported in the literature. While there are many REE pre-concentration procedures in the literature, our tests have shown these methods have difficulty at TDS greater than seawater (roughly 35,000 ppm TDS). Therefore, the ability to quantitatively measure REE's in formation brines with very high TDS has required the modification of an already developed procedure. After careful consideration and testing we selected methods modified after those described by Kingston et al., 1978 and Strachan et al., 1989 utilizing chelating media for very high TDS waters and ion-exchange media as detailed by Crock et al., 1984; Robinson et al., 1985; and Stetzenbach et al., 1994 for low TDS (<10,000 ppm TDS) waters. These modified procedures have been successfully tested in our laboratory and have proven effective in greatly

  18. Effect of acidification and salt concentration on two black brined olives from Sicily (cv moresca and giarraffa)

    Energy Technology Data Exchange (ETDEWEB)

    Romeo, F. V.; Piscopo, A.; Poiana, M.

    2010-07-01

    In the present work the effects of different brining treatments on mature table olives during natural fermentation were evaluated. The considered olive cultivars are typical of Sicily: Moresca and Giarraffa. They were harvested at pigmented state. The carpological data revealed their good quality as table olives. Natural fermentation was performed with or without acidification up to pH 4, and at 8% and 15% salt concentrations. The physical, chemical and microbiological changes in olives and brines were monitored throughout the processing period. The acidification affected and selected the microbial population and maintained the low pH necessary for the hygienic safety of the product. In fact, in Moresca brines,the lactic acid bacteria totally disappeared after 60 days of fermentation while in Giarraffa they maintained their presence in the brines up to 180 days with a value between 10{sup 4} UFC/mL and 106 UFC/mL, depending on the salt concentration. The microbial population was also affected by the polyphenol content, which was different between the cultivars. The color of olive fruits was greatly influenced by acidification and less by salt concentration. The addition of salt showed a different influence on the studied cultivars, in fact only the chemical analyses of Giarraffa showed a significant difference between the two levels of salt concentration. (Author) 19 refs.

  19. Evaluation of materials for systems using cooled, treated geothermal or high-saline brines

    Energy Technology Data Exchange (ETDEWEB)

    Suciu, D.F.; Wikoff, P.M.

    1982-09-01

    Lack of adequate quantities of clean surface water for use in wet (evaporative) cooling systems indicates the use of high-salinity waste waters, or cooled geothermal brines, for makeup purposes. High-chloride, aerated water represents an extremely corrosive environment. In order to determine metals suitable for use in such an environment, metal coupons were exposed to aerated, treated geothermal brine salted to a chloride concentration of 10,000 and 50,000 ppM (mg/L) for periods of up to 30 days. The exposed coupons were evaluated to determine the general, pitting, and crevice corrosion characteristics of the metals. The metals exhibiting corrosion resistance at 50,000 ppM chloride were then evaluated at 100,000 and 200,000 ppM chloride. Since these were screening tests to select materials for components to be used in a cooling system, with primary emphasis on condenser tubing, several materials were exposed for 4 to 10 months in pilot cooling tower test units with heat transfer for further corrosion evaluation. The results of the screening tests indicate that ferritic stainless steels (29-4-2 and SEA-CURE) exhibit excellent corrosion resistance at all levels of chloride concentration. Copper-nickel alloys (70/30 and Monel 400) exhibited excellent corrosion resistance in the high-saline water. The 70/30 copper-nickel alloy, which showed excellent resistance to general corrosion, exhibited mild pitting in the 30-day tests. This pitting was not apparent, however, after 6 months of exposure in the pilot cooling tower tests. The nickel-base alloys exhibited excellent corrosion resistance, but their high cost prevents their use unless no other material is found feasible. Other materials tested, although unsuitable for condenser tubing material, would be suitable as tube sheet material.

  20. Manufacture of Boron-free Magnesia with High Purity from Residual Brine

    Institute of Scientific and Technical Information of China (English)

    Fa Qiang LI; Bao Ping LING; Pei Hua MA

    2004-01-01

    A novel method for removing boron with ion exchange resin from residual brines to manufacture boron-free magnesia is described. The concentration of boron in the target magnesia manufactured thereby from Qinghai salt lakes is lower than 5μg/g, and the typical D50 size of product is 10.625μm.

  1. Modeling Coupled THM Processes and Brine Migration in Salt at High Temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Rutqvist, Jonny [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Blanco-Martin, Laura [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Molins, Sergi [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Trebotich, David [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Birkholzer, Jens [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2015-09-01

    In this report, we present FY2015 progress by Lawrence Berkeley National Laboratory (LBNL) related to modeling of coupled thermal-hydrological-mechanical-chemical (THMC) processes in salt and their effect on brine migration at high temperatures. This is a combined milestone report related to milestone Salt R&D Milestone “Modeling Coupled THM Processes and Brine Migration in Salt at High Temperatures” (M3FT-15LB0818012) and the Salt Field Testing Milestone (M3FT-15LB0819022) to support the overall objectives of the salt field test planning.

  2. Forward Osmosis Brine Drying

    Science.gov (United States)

    Flynn, Michael; Shaw, Hali; Hyde, Deirdre; Beeler, David; Parodi, Jurek

    2015-01-01

    The Forward Osmosis Brine Drying (FOBD) system is based on a technique called forward osmosis (FO). FO is a membrane-based process where the osmotic potential between brine and a salt solution is equalized by the movement of water from the brine to the salt solution. The FOBD system is composed of two main elements, the FO bag and the salt regeneration system. This paper discusses the results of testing of the FO bag to determine the maximum water recovery ratio that can be attained using this technology. Testing demonstrated that the FO bag is capable of achieving a maximum brine water recovery ratio of the brine of 95%. The equivalent system mass was calculated to be 95 kg for a feed similar to the concentrated brine generated on the International Space Station and 86 kg for an Exploration brine. The results have indicated that the FOBD can process all the brine for a one year mission for between 11% to 10% mass required to bring the water needed to make up for water lost in the brine if not recycled. The FOBD saves 685 kg and when treating the International Space Station brine and it saves 829 kg when treating the Exploration brine. It was also demonstrated that saturated salt solutions achieve a higher water recovery ratios than solids salts do and that lithium chloride achieved a higher water recovery ratio than sodium chloride.

  3. Brine treatment test for reinjection on Cerro Prieto geothermal field

    Energy Technology Data Exchange (ETDEWEB)

    Hurtado, R.; Mercado, S.; Gamino, H. (Departamento de Geotermia, Division de Fuentes de Energia, Instituto de Investigaciones Electricas, Justo Sierra y Herreros Sur 2098-Altos C.P. 21020, Mexicali, B.C. (MX))

    1989-01-01

    Reinjection of disposal brine from the Cerro Prieto Geothermal Power Plant System is attractive mainly because, on top of solving the brine disposal problem, it may significantly contribute to extend the reservoir useful lifetime, through thermal and hydraulic recharge. Because the high concentration of colloidal silica in the disposal brine, laboratory and pilot plant tests were conducted in order to develop the brine treatment process. Addition of 20-40 mg/1 lime to flashed and aged brine for 10-20 minutes yields a clarified brine relatively low in suspended solids (10-30 mg/1) when the over flow rate is 38.5 1/min-m/sup 2/. 1.1 mills/kWh was the estimated cost for treatment of 800 kg/s of separated brine from the Cerro Prieto I power station.

  4. A novel fucosyl glycosphingolipid of brine shrimp that is highly sensitive to endoglycoceramidase.

    Science.gov (United States)

    Xu, Xu; Horibata, Yasuhiro; Inagaki, Masanori; Hama, Yoichiro; Sakaguchi, Keishi; Goda, Hatsumi M; Okino, Nozomu; Ito, Makoto

    2009-12-01

    Endoglycoceramidase (EGCase; EC 3.2.1.123) is a glycohydrolase that hydrolyzes the glycosidic linkage between the oligosaccharide and ceramide of various glycosphingolipids. We previously reported that hydra produced EGCase to digest glycosphingolipids of brine shrimp (Artemia salina), a type of aquatic crustacean used as a diet for the culture of hydra (Horibata Y, Sakaguchi K, Okino N, Iida H, Inagaki M, Fujisawa T, Hama Y, Ito M. 2004. J Biol Chem. 279:33379-33389). We report here that a major glycosphingolipid of brine shrimp is unique in structure and highly sensitive to EGCase. The glycosphingolipid was extracted from freshly hatched brine shrimp by Folch's partition, followed by mild alkaline hydrolysis and purification with a Sep-Pak plus silica cartridge. The structure of brine shrimp glycosphingolipid was determined by gas chromatography, gas chromatography-mass spectrometry, fast-atom bombardment mass spectrometry, and (1)H-NMR spectrometry to be GlcNAcalpha1-2Fucalpha1-3Manbeta1-4Glcbeta1-1'Cer. Two major molecular species of the glycosphingolipid were identified; the sugar and sphingoid base of each were the same but the major fatty acid was C22:0 and 2-hydroxy C22:0, respectively. This is the first report describing the glycosphingolipid that has an internal fucosyl residue substituted with alpha1-2 N-acetylglucosaminyl residue. This study also suggests the biological relevance of the glycosphingolipid as a dietary source of hydra which possesses EGCase as a digestion enzyme.

  5. Coiled Brine Recovery Assembly (CoBRA): A New Approach to Recovering Water from Wastewater Brines

    Science.gov (United States)

    Pensinger, Stuart J.

    2015-01-01

    Brine water recovery represents a current technology gap in water recycling for human spaceflight. The role of a brine processor is to take the concentrated discharge from a primary wastewater processor, called brine, and recover most of the remaining water from it. The current state-of-the-art primary processor is the ISS Urine Processor Assembly (UPA) that currently achieves 70% water recovery. Recent advancements in chemical pretreatments are expected to increase this to 85% in the near future. This is a welcome improvement, yet is still not high enough for deep space transit. Mission architecture studies indicate that at least 95% is necessary for a Mars mission, as an example. Brine water recovery is the technology that bridges the gap between 85% and 95%, and moves life support systems one step closer to full closure of the water loop. Several brine water recovery systems have been proposed for human spaceflight, most of them focused on solving two major problems: operation in a weightless environment, and management and containment of brine residual. Brine residual is the leftover byproduct of the brine recovery process, and is often a viscous, sticky paste, laden with crystallized solid particles. Due to the chemical pretreatments added to wastewater prior to distillation in a primary processor, these residuals are typically toxic, which further complicates matters. Isolation of crewmembers from these hazardous materials is paramount. The Coiled Brine Recovery Assembly (CoBRA) is a recently developed concept from the Johnson Space Center that offers solutions to these challenges. CoBRA is centered on a softgoods evaporator that enables a passive fill with brine, and regeneration by discharging liquid brine residual to a collection bag. This evaporator is meant to be lightweight, which allows it to be discarded along with the accumulated brine solids contained within it. This paper discusses design and development of a first CoBRA prototype, and reports

  6. Brine Distribution after Vacuum Saturation

    DEFF Research Database (Denmark)

    Hedegaard, Kathrine; Andersen, Bertel Lohmann

    1999-01-01

    Experiments with the vacuum saturation method for brine in plugs of chalk showed that a homogeneous distribution of brine cannot be ensured at saturations below 20% volume. Instead of a homogeneous volume distribution the brine becomes concentrated close to the surfaces of the plugs...

  7. High epibenthic foraminiferal δ13C in the Recent deep Arctic Ocean: Implications for ventilation and brine release during stadials

    Science.gov (United States)

    Mackensen, Andreas

    2013-09-01

    Low planktic and benthic δ18O and δ13C values in sediments from the Nordic seas of cold stadials of the last glaciation have been attributed to brines, formed similar to modern ones in the Arctic Ocean. To expand on the carbon isotopes of this hypothesis, I investigated benthic δ13C from the modern Arctic Ocean. I show that mean δ13C values of live epibenthic foraminifera from the deep Arctic basins are higher than mean δ13C values of upper slope epibenthic foraminifera. This agrees with mean high δ13C values of dissolved inorganic carbon (DIC) in Arctic Bottom Water (ABW), which are higher than mean δ13CDIC values from shallower water masses of mainly Atlantic origin. However, adjustments for oceanic 13C Suess depletion raise subsurface and intermediate water δ13CDIC values over ABW δ13CDIC ones. Accordingly, during preindustrial Holocene times, the δ13CDIC of ABW was as high or even higher than today but lower than the δ13CDIC of younger subsurface and intermediate water. If brine-enriched water significantly ventilated ABW, brines should have had high δ13CDIC values. Analogously, high-δ13CDIC brines may have been formed in the Nordic seas during warm interstadials. During cold stadials, when most of the Arctic Ocean was perennially sea ice covered, a cessation of high-δ13CDIC brine rejection may have lowered δ13CDIC values of ABW, and ultimately the δ13CDIC in Nordic seas intermediate and deep water. So in contrast to the idea of enhanced brine formation during cold stadials, the results of this investigation imply that a cessation of brine rejection would be more likely.

  8. Effect of acidification and salt concentration on two black brined olives from Sicily (cv moresca and giarraffa

    Directory of Open Access Journals (Sweden)

    Romeo, Flora V.

    2010-09-01

    Full Text Available In the present work the effects of different brining treatments on mature table olives during natural fermentation were evaluated. The considered olive cultivars are typical of Sicily: Moresca and Giarraffa. They were harvested at pigmented state. The carpological data revealed their good quality as table olives. Natural fermentation was performed with or without acidification up to pH 4, and at 8% and 15% salt concentrations. The physical, chemical and microbiological changes in olives and brines were monitored throughout the processing period. The acidification affected and selected the microbial population and maintained the low pH necessary for the hygienic safety of the product. In fact, in Moresca brines,the lactic acid bacteria totally disappeared after 60 days of fermentation while in Giarraffa they maintained their presence in the brines up to 180 days with a value between 104 UFC/mL and 106 UFC/mL, depending on the salt concentration. The microbial population was also affected by the polyphenol content, which was different between the cultivars. The color of olive fruits was greatly influenced by acidification and less by salt concentration. The addition of salt showed a different influence on the studied cultivars, in fact only the chemical analyses of Giarraffa showed a significant difference between the two levels of salt concentration.

    En el presente trabajo, los efectos de diferentes tratamientos con salmuera en aceitunas de mesa maduras durante su fermentación natural fueron evaluados. Los cultivos de aceitunas considerados son típicos de Sicilia: Moresca y Giarraffa. Ellas son cosechadas en su estado maduro. Los datos carpológicos revelan su buena calidad como aceituna de mesa. La fermentación natural fue realizada con y sin acidificación hasta pH 4, y a una concentración de sal del 8% y 15%. Cambios físicos, químicos y microbiológicos de las aceitunas y salmueras a través de todo el

  9. Texture and antioxidant evolution of naturally green table olives as affected by different sodium chloride brine concentrations

    Directory of Open Access Journals (Sweden)

    Fadda, C.

    2014-03-01

    Full Text Available The results on the evolution of the texture and antioxidant activity during the processing of naturally fermented green olives are reported in the present study. The olives were brined with two different NaCl concentrations, 4 and 7%. A puncture test and a texture profile analysis (TPA test were carried out to evaluate texture, while the antioxidant activity was assessed in consideration of the loss of absorbance of a stable radical upon reaction with a polyphenolic olive extract. The puncture test revealed both an increase and decrease in peel and flesh hardness, respectively. The olives processed with 7% NaCl concentration showed higher peel hardness than olives brined with 4% salt. The texture profile analysis did not reveal any difference between the two salt concentrations used, but showed a decrease in the value of all parameters after 30 days of brining. The antioxidant activity of the polyphenolic extract decreased significantly during processing, with a major loss after the first 30 days of processing and was higher in the 7% brined olives, than the sample treated with 4% NaCl.En este trabajo se presentan los resultados sobre la evolución de la textura y la actividad antioxidante durante el proceso de fermentación natural de las aceitunas verdes. Los frutos se colocaron en salmueras con dos concentraciones de NaCl del 4% y 7%. Se evaluó la textura mediante ensayo de perforación y mediante análisis de perfil de textura (TPA, mientras que la actividad antioxidante se evaluó considerando la pérdida de absorbancia de un radical estable tras la reacción con un extracto polifenólico de las aceitunas. El ensayo de perforación reveló un aumento de la dureza de la piel y una reducción en la dureza de la pulpa. Las aceitunas procesadas con una concentración de NaCl del 7% mostraron una dureza mayor que aquellas tratadas con sal al 4%. El análisis del perfil de la textura no reveló diferencias entre las dos concentraciones usadas de

  10. Primary proteolysis of white brined goat cheese monitored by high molarity Tris buffer SDS- PAGE system

    Directory of Open Access Journals (Sweden)

    Milenko Smiljanić

    2013-08-01

    Full Text Available The aim of this work was to investigate primary proteolysis of white brined goat cheese prepared from raw milk and to correlate with the results obtained with high-molarity Tris buffer electrophoretic system. Proteolytic changes of white brined cheese were monitored by three parameters, the total protein, the water soluble proteins and the degree of proteolysis, whereas the change of major casein fractions was followed by electrophoresis in reducing conditions. Ripening caused a decrease of the total protein content, whereas in the first forty days the water soluble protein and the degree of proteolysis increased. Both casein fractions (αs- and β-casein of goat cheese were susceptible to primary proteolysis but to the different extent. αs1- casein disappeared during processing, whereas during 60-days of ripening the content of αs2 and β-casein was reduced by 38.90 %, and 30.72 %, respectively. Such trends of major casein fractions were strongly correlated with the degree of proteolysis and the moisture content, whereas no correlation was found between them and the water soluble protein content. The results of our investigation clearly suggested that SDS-PAGE method based on high-molarity Tris-buffer system could be a very useful for purposes of monitoring the white goat cheese proteolysis.

  11. Modeling Coupled THMC Processes and Brine Migration in Salt at High Temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Rutqvist, Jonny; Blanco Martin, Laura; Mukhopadhyay, Sumit; Houseworth, Jim; Birkholzer, Jens

    2014-08-14

    In this report, we present FY2014 progress by Lawrence Berkeley National Laboratory (LBNL) related to modeling of coupled thermal-hydrological-mechanical-chemical (THMC) processes in salt and their effect on brine migration at high temperatures. LBNL’s work on the modeling of coupled THMC processes in salt was initiated in FY2012, focusing on exploring and demonstrating the capabilities of an existing LBNL modeling tool (TOUGH-FLAC) for simulating temperature-driven coupled flow and geomechanical processes in salt. This work includes development related to, and implementation of, essential capabilities, as well as testing the model against relevant information and published experimental data related to the fate and transport of water. we provide more details on the FY2014 work, first presenting updated tools and improvements made to the TOUGH-FLAC simulator, and the use of this updated tool in a new model simulation of long-term THM behavior within a generic repository in a salt formation. This is followed by the description of current benchmarking and validations efforts, including the TSDE experiment. We then present the current status in the development of constitutive relationships and the dual-continuum model for brine migration. We conclude with an outlook for FY2015, which will be much focused on model validation against field experiments and on the use of the model for the design studies related to a proposed heater experiment.

  12. Natural Oxidation of Bromide to Bromine in Evaporated Dead Sea Brines

    Science.gov (United States)

    Gavrieli, Ittai; Golan, Rotem; Lazar, Boaz; Baer, Gidi; Zakon, Yevgeni; Ganor, Jiwchar

    2016-04-01

    Highly evaporated Dead Sea brines are found in isolated sinkholes along the Dead Sea. Many of these brines reach densities of over 1.3 kg/L and pHDead Sea brine that drain into the sinkholes. The low pH and the reddish to brownish hue of these brines were an enigma until recently. Despite the rather high total alkalinity (TA) of the Dead Sea (3.826 mmol/kg) the pH of the Dead Sea brine is known to be slightly acidic with a value of ~6.3. In comparison, seawater with the same alkalinity would have a pH value well above 8.3, meaning that H+ activity is 100 fold lower than that of Dead Sea brine. In the present work we assess the apparent dissociation constant value of boric acid (K`B) for the Dead Sea brine and use it to explain the brine's low pH value. We then show that pH decreases further as the brine evaporates and salinity increases. Finally we explain the reddish hue of the hypersaline brines in the sinkholes as due to the presence of dissolved bromine. The latter is the product of oxidation of dissolved bromide, a process that is enabled by the low pH of the hypersaline brines and their high bromide concentration.

  13. Diversity and characterization of mercury-resistant bacteria in snow, freshwater and sea-ice brine from the High Arctic

    DEFF Research Database (Denmark)

    Møller, Annette; Barkay, Tamar; Abu Al-Soud, Waleed;

    2011-01-01

    It is well-established that atmospheric deposition transports mercury from lower latitudes to the Arctic. The role of bacteria in the dynamics of the deposited mercury, however, is unknown. We characterized mercury-resistant bacteria from High Arctic snow, freshwater and sea-ice brine. Bacterial...... densities were 9.4 × 10(5), 5 × 10(5) and 0.9-3.1 × 10(3) cells mL(-1) in freshwater, brine and snow, respectively. Highest cultivability was observed in snow (11.9%), followed by freshwater (0.3%) and brine (0.03%). In snow, the mercury-resistant bacteria accounted for up to 31% of the culturable bacteria, but...

  14. Diversity and characterization of mercury-resistant bacteria in snow, freshwater and sea-ice brine from the High Arctic.

    Science.gov (United States)

    Møller, Annette K; Barkay, Tamar; Abu Al-Soud, Waleed; Sørensen, Søren J; Skov, Henrik; Kroer, Niels

    2011-03-01

    It is well-established that atmospheric deposition transports mercury from lower latitudes to the Arctic. The role of bacteria in the dynamics of the deposited mercury, however, is unknown. We characterized mercury-resistant bacteria from High Arctic snow, freshwater and sea-ice brine. Bacterial densities were 9.4 × 10(5), 5 × 10(5) and 0.9-3.1 × 10(3) cells mL(-1) in freshwater, brine and snow, respectively. Highest cultivability was observed in snow (11.9%), followed by freshwater (0.3%) and brine (0.03%). In snow, the mercury-resistant bacteria accounted for up to 31% of the culturable bacteria, but Arctic food chains.

  15. Contaminants of emerging concern in reverse osmosis brine concentrate from indirect/direct water reuse applications.

    Science.gov (United States)

    Romeyn, Travis R; Harijanto, Wesley; Sandoval, Sofia; Delagah, Saied; Sharbatmaleki, Mohamadali

    2016-01-01

    Water shortage is becoming more common due to droughts and global population increases resulting in the increasing popularity of water reuse to create new water sources. Reverse osmosis (RO) membrane systems are popular in these applications since they can produce drinking water quality effluent. Unfortunately, RO systems have the drawback of generating concentrate streams that contain contaminants rejected by the membrane including chemicals of emerging concern (CECs). CECs are chemicals such as hormones, steroids, pesticides, pharmaceuticals, and personal care products that are used for their intended purpose and then released into wastewater. CECs are believed to be detrimental to aquatic wildlife health and pose an unknown human health risk. This research gathered the existing knowledge on CEC presence in concentrate, available proven concentrate treatment methods, their CEC removal abilities, and current CEC regulations. It was found that 127 CECs have been measured in RO concentrate with 100 being detected at least once. The most potent treatment process available is UV/H2O2 as it offers the highest removal rates for the widest range of chemicals. The less expensive process of ozone/biologically activated carbon offers slightly lower removal abilities. This comprehensive report will provide the groundwork for better understanding, regulating and treating concentrate stream CECs.

  16. Experimental Study and Stabilization Mechanisms of Silica Nanoparticles Based Brine Mud with High Temperature Resistance for Horizontal Shale Gas Wells

    Directory of Open Access Journals (Sweden)

    Xian-yu Yang

    2015-01-01

    Full Text Available Previous studies showed that silica nanoparticles based fresh water drilling muds had good thermal stability up to 160°C; however its performance at high salt concentration was rather poor. Therefore, high performance silica nanoparticles based brine mud (NPBMs with high temperature resistance for horizontal shale gas wells was proposed. Thermal stability tests from ambient temperature to 180°C, along with pressure transmission tests and rheology analysis, were performed to evaluate comprehensive properties of the NPBMs. Results show that the NPBMs embody excellent salt tolerance and thermal resistance for their rheological parameters did not suffer significant fluctuation. Fluid loss of the NPBM-1 (4% NaCl plus 3% KCl at 180°C was only 7.6 mL while the NPBM-2 (10% NaCl plus 3% KCl had a fluid loss of 6.6 mL at 150°C. Low water activity and good lubricity of the NPBMs were beneficial to improve wellbore stability and reduce friction resistance. Pressure transmission tests on the NPBM-1 show that it can mitigate or even prevent the transmission of drilling mud pressure into shale thus improving wellbore stability. Additionally, optimal rheological models for the NPBM-1 and the NPBM-2 were Herschel-Bulkley model and Power Law model separately.

  17. Mercuric reductase genes (merA) and mercury resistance plasmids in High Arctic snow, freshwater and sea-ice brine.

    Science.gov (United States)

    Møller, Annette K; Barkay, Tamar; Hansen, Martin A; Norman, Anders; Hansen, Lars H; Sørensen, Søren J; Boyd, Eric S; Kroer, Niels

    2014-01-01

    Bacterial reduction in Hg(2+) to Hg(0) , mediated by the mercuric reductase (MerA), is important in the biogeochemical cycling of Hg in temperate environments. Little is known about the occurrence and diversity of merA in the Arctic. Seven merA determinants were identified among bacterial isolates from High Arctic snow, freshwater and sea-ice brine. Three determinants in Bacteriodetes, Firmicutes and Actinobacteria showed 99% similar to known merA's. Phylogenetic analysis showed the Bacteroidetes merA to be part of an early lineage in the mer phylogeny, whereas the Betaproteobacteria and Gammaproteobacteria merA appeared to have evolved recently. Several isolates, in which merA was not detected, were able to reduce Hg(2+) , suggesting presence of unidentified merA genes. About 25% of the isolates contained plasmids, two of which encoded mer operons. One plasmid was a broad host-range IncP-α plasmid. No known incompatibility group could be assigned to the others. The presence of conjugative plasmids, and an incongruent distribution of merA within the taxonomic groups, suggests horizontal transfer of merA as a likely mechanism for High Arctic microbial communities to adapt to changing mercury concentration.

  18. Sensitivity of Some Explosive/Brine Mixtures

    Science.gov (United States)

    1980-08-01

    concentration in brine mixtures. 3 Friction test results of brine mixtures. 10 4 Thermal test results of brine mixtures. 11 Li 71 - INTRODUCTION A...also carried out on these impact insensitive mixtures. Of the seven mixtures only the 15% M28-Comp. B sample passed the thermal test , since smoking

  19. 不同浓度盐水对鸭肉湿腌时传质动力的影响%Influence of brine concentration on mass transfer kinetics of duck during wet-curing

    Institute of Scientific and Technical Information of China (English)

    杜垒; 李艳逢; 周光宏; 徐幸莲; 王进; 肖治国; 陶明财

    2011-01-01

    Firstly , duck thigh meat were wet-cured using old brine which brined the water- boiled salted duck and other brine concentrations (5%, 15 % and 25% NaCl, w/w) following with the production process of water- boiled salted duck which was wet-curing after dry-curing ,then the changes of salt,water content and total weight were analyzed and intended to obtain the first data of mass transfer kinetics for duck thigh meat under different brine concentration and information of the basic mechanism of salted process. Results indicated that the brine concentration significantly affected the total weight changes of the duck thigh meat. The weight change and water content of the duck thigh meat increased with decreasing brine concentration, the salt content had an opposite change. 15 % NaCl(w/w) brine,the moderate salt concentration, was the most suitable for wet- curing just because of its higher process yields with high De value and lower health risks. Moreover,there were good linear relationships between total weight change and curing time, the correlation coefficients were all good. Experiments verified that the kinetics model was fit to curing process.%研究采用盐水鸭生产时使用的过饱和盐水--老卤和其他三种不同浓度的盐水(5%、15%和25%NaCl,w/w)对鸭腿肉按照盐水鸭的生产过程进行腌制,通过对腌制过程中鸭腿肉的食盐、水分和总重变化进行测定,以期获得不同盐水浓度下鸭肉的传质动力学数据,并获得腌制最适盐水浓度.结果表明,盐水浓度显著影响鸭腿肉在腌制过程中的传质变化.鸭腿肉的重量变化、水分获得都是随着盐水溶液浓度的降低而增加,盐分变化则相反.中等浓度的盐水溶液(15%NaCl,w/w)腌制的鸭肉产量较高,有较高的扩散速率--De值,对人体的损害较小.因此,较为适于用来腌制鸭肉.另外,腌制的预测模型和扩散公式计算得到的数据都有良好的线性关系,可以很好地适用于鸭腿肉的腌制实验研究.

  20. Optimal concentration of local well brine groundwater irrigation for Bamboo willow introduced to the arid areas in northern Xinjiang province, China

    Science.gov (United States)

    Han, Wei; Cao, Ling; Zhang, Ya; Cui, Kaiqiang; Wu, Shengli

    2015-04-01

    The adaptation and survive of introduced plants to local well brine groundwater irrigation is an important issue, while people introduce some plants to improve the local environment in the construction of urban greening oases in arid areas, north China. We measured some of the photosynthetic characteristics of introduced Bamboo willow irrigated by different local well brine groundwater in the wild controlled experiments, in May 2014 in Kelamayi city in north China, which to seek the most appropriate irrigation concentration of underground saline water, and to clarify the physiological ecological adaptation to the local habitat. The parameters, measured by Li-6400XT, a portable photosynthesis system, include the following ones, net photosynthetic rate (Pn), stomatal conductance (Gs), transpiration rate (Tr), the internal CO2 concentration (Ci) and efficiency of water application (WUE) of one-year old introduced Bamboo willow irrigated by set salinity groundwater gradient, as 0 g/L, 5 g/L and 10 g/L. the results showed that (1) In each salt water concentration, the diurnal variation curve of net photosynthetic rate showed as "bimodal curve" style, and obvious "midday depression". (2) The parameter Pn of Bamboo willow irrigated by salt water of 5g/L was highest compared with the other two, and the value Pn irrigated by salt water concentration of 10g/L down. The net photosynthetic rate would increase in the salt concentration of 10g/L. In conclusion, the salt groundwater concentration of 10g/L was the optimal concentration of local well brine groundwater irrigation for Bamboo willow introduced to the arid areas in northern Xinjiang province, China.

  1. Influence of brine concentration on sugar and sodium chloride diffusion during the processing of the green olive variety Arauco

    Directory of Open Access Journals (Sweden)

    Miras, N.

    2008-09-01

    Full Text Available The green olive variety Arauco were debittered using lye concentrations of, 2.50% NaOH.They were then subjected to two rinsing processes with tap water. Next, the olives were cured with brines at 7%, 10% and 13% sodium chloride concentration. During this curing process, the loss of reducing sugars from the olives, and the diffusion of sodium chloride into the olives were quantified. Effective diffusion coefficients of both solutes in the skin and the flesh were calculated for this period using a diffusion model for a composite hollow sphere. The skin effective diffusion coefficients for both solutes ranged from entre 8,27x10-14- m2/s to 4,04x10-13 m2/s. The flesh coefficients varied from 2,92x10-9 m2/s to 3,99x10-9 m2/s for sodium chloride and from 9,76x10-11 m2/s to 2,22x10-10 m2/s for reducing sugars.Aceitunas verdes variedad Arauco fueron tratadas con soluciones de hidróxido de sodio al 2,5%. Estas fueron luego sometidas a dos procesos de lavado con agua corriente. Posteriormente, las aceitunas fueron curadas en salmueras con concentraciones de 7%, 10% y 13% de cloruro de sodio. Durante este proceso de curado, se cuantificó la pérdida de azúcares reductores desde, y la difusión de cloruro de sodio hacia el interior de las aceitunas. Durante este período se calcularon los coeficientes efectivos de difusión de ambos solutos en la piel y la pulpa, utilizando un modelo de difusión en una esfera hueca compuesta. Los coeficientes efectivos de difusión de ambos solutos en la piel estuvieron en un rango entre 8,27x10-14- m2/s y 4,04x10-13 m2/s. Los coeficientes de la pulpa variaron entre 2,92x10-9 m2/s y 3,99x10-9 m2/s para el cloruro de sodio, y entre 9,76x10-11 m2/s y 2,22x10-10 m2/s para los azúcares reductores.

  2. Changes in microbial diversity of brined green asparagus upon treatment with high hydrostatic pressure.

    Science.gov (United States)

    Toledo Del Árbol, Julia; Pérez Pulido, Rubén; La Storia, Antonietta; Grande Burgos, Maria José; Lucas, Rosario; Ercolini, Danilo; Gálvez, Antonio

    2016-01-01

    The application of high hydrostatic pressure (HHP, 600MPa, 8 min) on brined green asparagus and the changes in bacterial diversity after treatments and during storage at 4 °C (30 days) or 22 °C (10 days) were studied. HHP treatments reduced viable cell counts by 3.6 log cycles. The residual surviving population did not increase during storage at 4 °C. However, bacterial counts significantly increased at 22 °C by day 3, leading to rapid spoilage. The microbiota of green asparagus was composed mainly by Proteobacteria (mainly Pantoea and Pseudomonas), followed by Firmicutes (mainly Lactococcus and Enterococcus) and to a less extent Bacteroidetes and Actinobacteria. During chill storage of untreated asparagus, the relative abundance of Proteobacteria as well as Enterococcus and Lactococcus decreased while Lactobacillus increased. During storage of untreated asparagus at 22 °C, the abundance of Bacteroidetes decreased while Proteobacteria increased during late storage. The HHP treatment determined a reduction of the Proteobacteria both early after treatment and during chill storage. In the HHP treated samples stored at 22 °C, the relative abundance of Pseudomonas rapidly decreased at day 1, with an increase of Bacteroidetes. This was followed by a marked increase in Enterobacteriaceae (Escherichia) simultaneously with increase in viable counts and spoilage. Results from the study indicate that the effect of HHP treatments on the viability ofmicrobial populations in foods also has an impact on the dynamics of microbial populations during the storage of the treated foods.

  3. Prediction of oxygen solubility in pure water and brines up to high temperatures and pressures

    Science.gov (United States)

    GENG, Ming; DUAN, Zhenhao

    2010-10-01

    A thermodynamic model is presented to calculate the oxygen solubility in pure water (273-600 K, 0-200 bar) and natural brines containing Na +, K +, Ca 2+, Mg 2+, Cl -, SO 42-, over a wide range of temperature, pressure and ionic strength with or close to experimental accuracy. This model is based on an accurate equation of state to calculate vapor phase chemical potential and a specific particle interaction model for liquid phase chemical potential. With this approach, the model can not only reproduce the existing experimental data, but also extrapolate beyond the data range from simple aqueous salt system to complicated brine systems including seawater. Compared with previous models, this model covers much wider temperature and pressure space in variable composition brine systems. A program for this model can be downloaded from the website: http://www.geochem-model.org.

  4. A study of the corrosion products of mild steel in high ionic strength brines.

    Science.gov (United States)

    Wang, Z; Moore, R C; Felmy, A R; Mason, M J; Kukkadapu, R K

    2001-01-01

    The corrosion layer on steel surfaces that formed after exposure to waste isolation pilot plant (WIPP) brines under anoxic conditions was characterized for chemical composition, thickness and phase composition. The chemical composition of the corrosion layer was determined both by X-ray photoelectron spectroscopy (XPS) and by chemical analysis of acid solutions used to remove the corrosion layer. Atomic force microscopic (AFM) images indicated that the brine-corroded surface layer shows extensive granulation along the contours of the steel surface that is characteristic of sharp polishing marks. The corrosion layer seemed to be porous and could be dissolved and detached in dilute hydrochloric acid. The corrosion layer appears to be composed of iron oxides with some ionic substitutions from the brines. The 77 K Mössbauer spectrum recorded for iron powder leached under similar conditions indicated the corrosion layer was comprised principally of green rust.

  5. Primary proteolysis of white brined cheese prepared from raw cow milk monitored by high-molarity Tris buffer SDS-PAGE system

    National Research Council Canada - National Science Library

    Milenko Smiljanić; Mirjana B. Pesic; Sladjana P. Stanojevic; Miroljub B. Barać

    2014-01-01

    The aim of this work was to investigate primary proteolysis of white brined cow cheese prepared from raw milk by SDS-electrophoretic method based on high-molarity Tris buffer system and to correlate...

  6. Simulation of the high-pressure phase equilibria of hydrocarbon-water/brine systems

    DEFF Research Database (Denmark)

    Zuo, You-Xiang; Stenby, Erling Halfdan; Guo, Tian-Min

    1996-01-01

    The major objectives of this work are: (1) extend the modified Patel-Teja (MPT) equation of state proposed for aqueous electrolyte systems (Zuo and Guo, 1991) to describe the liquid-liquid and vapor-liquid-liquid equilibria of hydrocarbon-water/brine systems through introducing an unconventional ...

  7. Analysis of Abnormal Phenomena in High Magnesium Boron Containing Salt Brine System%高镁含硼盐卤体系反常现象解析

    Institute of Scientific and Technical Information of China (English)

    乌志明; 崔香梅; 郑绵平

    2012-01-01

    Such phenomena as "supersaturated solubility", "salt formation by dilution" and "solubility increase of homonymy ion" exist in high magnesium boron containing salt brine system. Our research indicates that the magnesium chloride solution is neutral with medium or low concentration. It shows acidic property with high concentration and the pH value is lower than 4.5 when saturated. But many types of magnesium borate minerals are alkaline ones with pH value higher than 8.0. We know in general acid and base could hardly co-exist in an aqueous solution, but magnesium borate and magnesium chloride in high magnesium boron containing salt brine system do owing to the possession of the homonymy ion. The above mentioned abnormal phenomena can be satisfactorily interpreted with special acidity change of magnesium chloride solution and some related phase chemistry data.%高镁含硼盐卤体系中存在“过饱和溶解度”、“稀释成盐”和同名离子“增溶”等反常现象.研究发现:氯化镁溶液在中低浓度时显中性,在高浓度时显酸性,饱和时pH值小于4.5.而各种镁硼酸盐基本都是pH值大于8.0的碱性矿物.水溶液中酸碱难共存,但镁硼酸盐与氯化镁却因具有相同离子而能够在高镁含硼盐卤体系中共存.结合氯化镁溶液特殊酸度变化规律与相关相化学数据可较圆满的解释高镁含硼盐卤体系中的反常现象.

  8. Pilot Study on MBBR Process to Treat Reverse Osmosis Concentrated Brine%MBBR工艺处理反渗透浓盐水中试研究

    Institute of Scientific and Technical Information of China (English)

    尹航; 杜娟; 盛培展; 祝群力; 苗利利; 余迎春

    2015-01-01

    The effect of the process of moving bed biofilm reactor (MBBR) in treatment of reverse osmosis concentrated brine in steel industry was investigated through field pilot-scale experiment. The results showed that the effect of MBBR to remove ammonia nitrogen is very obvious, with the removal above 90%. The effect of COD removal by MBBR is also good, with the removal rate above 70%. This pilot experiment provided valuable experience for future practical engineering.%通过现场中试考察了MBBR工艺处理钢铁企业反渗透浓盐水的效果。中试结果表明,MBBR对于氨氮的去除效果明显,去除率稳定在90%以上;对浓盐水中COD也有很好的去除效果,去除率达70%以上。

  9. Effects of dry brining, liquid smoking and high-pressure treatment on the physical properties of aquacultured King salmon (Oncorhynchus tshawytscha) during refrigerated storage.

    Science.gov (United States)

    Kong, Kelvin Jia Wey; Alçiçek, Zayde; Balaban, Murat O

    2015-03-15

    Aquacultured King salmon (Oncorhynchus tshawytscha) pieces were dry brined with a salt/brown sugar mix, dipped in liquid smoke for 3 min, vacuum packed, high hydrostatic pressure (HHP) treated at 600 or 200 MPa for 5 min and stored at 4 °C for up to 40 days. The surface redness (average a*) of the samples increased after dry brining, then decreased after liquid smoke treatment. HHP did not change the outside color of liquid-smoked samples. However, the inside color changed depending on pressure. HHP-treated control samples without dry brining and liquid smoking changed to a pale pink color. HHP at 600 MPa resulted in a significant increase in hardness. Compared with fresh samples, dry-brined samples had reduced water activity, while samples dipped in liquid smoke had lower pH values. Dry brining and liquid smoking protect the outside color of salmon against changes caused by HHP. The increase in hardness may counteract the softening of the smoked salmon tissue over time. © 2014 Society of Chemical Industry.

  10. High-order Cu(II) chloro-complexes in LiCl brines: Insights from density function theory and molecular dynamics

    Science.gov (United States)

    Li, Hui-Ji; Yi, Hai-Bo; Xu, Jia-Jia

    2015-09-01

    Cu(II) complexation by chloride is relevant to the transport of copper in near-surface geologic environments, yet the existence of high-order Cu(II) chloro-complexes still remains in dispute. In this study, the structure characteristics and stabilities of [CuClx]2-xaq (x = 3, 4, 5) complexes have been investigated using density functional theory (DFT) methods and molecular dynamics (MD) simulations. [CuCl3]- and [CuCl4]2- species can both be tracked, while the [CuCl5]3-aq complex cannot be recorded during MD simulations of trace Cu2+ in chloride-rich brines. DFT calculations indicate that contact ion pair (CIP) conformers of [CuCl3]- species are less stable than its solvent separated ion pair (SSIP) conformers, in which one Cl- stays in the second coordination sphere of the centered Cu2+. MD simulations also reveal that the SSIP conformer is apt to appear in the aqueous solution than its CIP conformer. It seems that the third Cl- is more likely in the second coordination shell of center Cu2+ in [CuCl3]-. Meanwhile, the characteristic peak around 385 nm resolved in UV-Vis spectra experiments, which was attributed to the [CuCl3]- complex, could also be resulted from some SSIP structures of the [CuCl3]- complex. In MD simulations, the complex [CuCl4]2-aq is found more stable than [CuCl3]-aq. The surrounding water molecules around [CuClx]2-xaq (x = 3, 4) enhance their stabilities in Cl- brines, especially for [CuCl4]2-aq. The hydration shell of [CuCl4]2-aq species is more intact than that of [CuCl3]2-aq, and the residence time of a water molecule in the second coordination sphere of Cu ion in the [CuCl4]2-aq complex is also obviously longer than that of [CuCl3]-aq. The [CuCl4]2-aq complex can even be recorded in the less concentrated (6.33 m) Cl- solution, while the [CuCl3]-aq complex is tracked only in the 16.32 m Cl- brine. Meanwhile, the possibilities of [CuCl3]-aq and [CuCl4]2-aq complexes found in 16.32 m Cl- solutions both decrease with increasing temperature

  11. APPLICATION OF HIGH-RESOLUTION MAGNETIC METHOD AND GRADIENT METHOD TO LOCATE ABANDONED BRINE-WELLS IN HUTCHINSON, KANSAS, U.S.A.

    Institute of Scientific and Technical Information of China (English)

    CHEN Chao; XIA Jianghai; XIA Sihao; David Laflen; Stephen L. Williams

    2004-01-01

    After successfully locating one abandoned brine well by an electromagnetic method during testing in 2001 and five abandoned brine wells by a high-resolution magnetic method during 2002, a high-resolution magnetic method was again proposed to search for wells in 2003 when a second sensor was employed to acquire data for calculating the pseudo-vertical gradient of magnetic fields. Total area surveyed in 2003 was 1,024,000 ft2, which was divided into grids with an average size of 10,000 ft2 and distributed across eight different sites. Magnetic anomalies and their vertical gradients from known brine wells were first recorded as signatures to identify anomalies caused by possible buried brine wells. Of fifty-one verified anomalies, thirtyone anomalies were due to wells buried at depths from 0 to 8.5 ft: twenty-one 6- to 9-inch abandoned brine wells, seven 1.5- to 3-inch probable water wells, one 16-inch dewatering well for a construction site at a depth of 3 ft, and two 4-inch wells on the ground surface. Approximate monopole shaped anomalies were observed from all these wells after data corrections. However, the range of amplitudes of magnetic anomalies from 7,000 to 28,000 nT from these abandoned brine wells was measured. This range of anomalies is mainly due to the thickness and depth of buried wells. Anomaly amplitudes from 1.5- to 3-inch wells are 4,000 to 8,000 nT and linearly correlate with the buried depth. One 3-inch well that caused an anomaly of 13,000 nT could be the inner pipe of a brine well. Gradient anomalies are roughly in a range of 100 to 200 nT/inch for 1.5-to 3-inch wells and 200 to 300 nT/inch for brine wells.As indicated by the potential-field theory, gradient data possess higher horizontal resolution than the magnetic field itself. Gradient data provide valuable assistance in determining horizontal locations of anomaly sources for excavation. In practice, however, improvement in the horizontal resolution is limited by surveyline spacing. If only

  12. Distillation Brine Purification for Resource Recovery Applications

    Science.gov (United States)

    Wheeler, Raymond M.

    2014-01-01

    Wastewater processing systems for space generate residual brine that contains water and salts that could be recovered to life support consumables. The project assessed the use of ion-exchange resins to selectively remove salts from wastewater treatment brines. The resins were then regenerated for additional use. The intention would be to generate a Na/K and CI rich or purified brine that would then be processed into high value chemicals, such as acids, bases, and/or bleach.

  13. Brine disposal process for Morcinek coal mine

    Energy Technology Data Exchange (ETDEWEB)

    Tait, J.H. [Aquatech Services, Inc., Citrus Heights, CA (United States)

    1995-04-01

    This paper describes the work to develop a commercial brine disposal process for the Morcinek mine, located 45 km south of the city of Katowice in Poland. Currently, brine is discharged into the Odra river and methane from the mine is released into the atmosphere. The process would use the released methane and convert a large percentage of the brine into potable water for commercial use. Thus, the proposed process has two environmental benefits. The brine salinity is about 31,100 ppm. Major brine components are Na (10,300 ppm), Ca (1,170 ppm), Mg (460 ppm), Cl (18,500 ppm) and SO{sub 4}{sup 2-} (252 ppm). Present in smaller amounts are K, S, Sr, B, Ba and NO{sub 3}. The process integrates a reverse osmosis (RO) unit and a submerged combustion evaporator. Extensive studies made at the Lawrence Livermore National Laboratory established the pretreatment method of the brine before it enters the RO unit. Without adequate pretreatment, mineral phases in the brine would become super-saturated and would precipitate in the RO unit. The pretreatment consists of first adding sodium carbonate to increase both the pH and the carbonate concentration of the brine. This addition causes precipitation of carbonate solids containing Ca, Mg, Sr, and Ba. After filtration of these precipitates, the fluid is acidified with HCl to prevent precipitation in the RO unit as the brine increases in salinity.

  14. CaCO/sub 3/ precipitation in high temperature and pressure brines in the presence of scale inhibitors using novel saturation index calculations

    Energy Technology Data Exchange (ETDEWEB)

    Oddo, J.E.; Sloan, K.B.; Tomson, M.B.; Bebout, D.G.; Bachman, A.L. (eds.)

    1981-01-01

    A simplified method to calculate CaCO/sub 3/ saturation is developed using only commonly measured field parameters. The calculated saturation index (SI) and pH values are shown to be accurate at high temperatures and pressures in brines and are compared to less sophisticated and more complex calculations.

  15. Primary proteolysis of white brined cheese prepared from raw cow milk monitored by high-molarity Tris buffer SDS-PAGE system

    Directory of Open Access Journals (Sweden)

    Milenko Smiljanić

    2014-05-01

    Full Text Available The aim of this work was to investigate primary proteolysis of white brined cow cheese prepared from raw milk by SDS-electrophoretic method based on high-molarity Tris buffer system and to correlate with the results of other commonly used parameters. Proteolytic changes of white brined cow cheese were monitored by three parameters: total protein, water soluble proteins and degree of proteolysis. Changes of major casein fractions were followed by SDS-electrophoretic system in reducing conditions. The total protein content and moisture content of white brined cow cheese were significantly affected by ripening. Ripening in brine increased water soluble proteins and degree of proteolysis. Major caseins were differently resistant to proteolysis; αs-CN was more susceptible than β-CN. The αs-CN content was highly and negatively correlated with time of ripening and water soluble proteins whereas no significant correlation (p<0.05 between β-CN content and these parameters was found. Also, a strong significant correlation (p<0.05 between the amount of low molecular weight products and time of ripening, water soluble proteins and αs-CN content was observed. SDS-PAGE method used in this study could be useful for monitoring the white cow cheese proteolysis.

  16. Predictive modeling of selenium accumulation in brine shrimp in saline environments.

    Science.gov (United States)

    Byron, Earl R; Ohlendorf, Harry M; Redman, Aaron; Adams, William J; Marden, Brad; Grosell, Martin; Brooks, Marjorie L

    2011-07-01

    Great Salt Lake, Utah, is a large, terminal, hypersaline lake consisting of a northern more saline arm and a southern arm that is less saline. The southern arm supports a seasonally abundant fauna of low diversity consisting of brine shrimp (Artemia franciscana), 7 species of brine flies, and multiple species of algae. Although fish cannot survive in the main body of the lake, the lake is highly productive, and brine shrimp and brine fly populations support large numbers of migratory waterfowl and shorebirds, as well as resident waterfowl, shorebirds, and gulls. Selenium and other trace elements, metals, and nutrients are contaminants of concern for the lake because of their concentrations in municipal and industrial outfalls and runoff from local agriculture and the large urban area of Salt Lake City. As a consequence, the State of Utah recently recommended water quality standards for Se for the southern arm of Great Salt Lake based on exposure and risk to birds. The tissue-based recommendations (as measured in bird eggs) were based on the understanding that Se toxicity is predominately expressed through dietary exposure, and that the breeding shorebirds, waterfowl, and gulls of the lake are the receptors of most concern. The bird egg-based recommended standards for Se require a model to link bird egg Se concentrations to their dietary concentrations and water column values. This study analyzes available brine shrimp tissue Se data from a variety of sources, along with waterborne and water particulate (potential brine shrimp diet) Se concentrations, in an attempt to develop a model to predict brine shrimp Se concentrations from the Se concentrations in surrounding water. The model can serve as a tool for linking the tissue-based water quality standards of a key dietary item to waterborne concentrations. The results were compared to other laboratory and field-based models to predict brine shrimp tissue Se concentrations from ambient water and their diet. No

  17. 高矿化度水样中微量铀的测定%Trace Uranium Determination in High Salinity Brine

    Institute of Scientific and Technical Information of China (English)

    白静; 赵梁; 范芳丽; 吴晓蕾; 丁华杰; 雷富安; 田伟; 秦芝; 郭俊盛

    2011-01-01

    With the development of nuclear power industry in our country, the needs for uranium will increase drastically. But as the uranium resource in uranium mines are very limited, much attention has been paid on the uranium recovery from other resources, such as sea water and high salinity brine. Accurate determination of uranium concentration is very important, if uranium recovery was performed on this complicate water. Trace uranium determination in high salinity brine, for instance, salt lake and intercrystalline bittern samples, was studied in present work by using ultraviolet fluorescence method. As the instrument is stable, the optimal conditions for uranium determination are found to be: pH = 2-12, added fluorescence-enhancing agent amount of 500 μL; to reduce the negative effect of impurity ions on uranium determination, both direct dilution and TBP extraction fluorescence methods are investigated. The procedure used for TBP extraction fluorescence method is confirmed by employing different solvents as TBP diluent, and the uranium recov-ery rate is determined to be 85%. Under the optimal conditions, both methods mentioned above were used for analyzing uranium concentration in salt lake and intercrystalline bittern samples. The obtained results were compared with those measured by inductively coupled plasma mass spectrometry (ICP-MS) method. Good consistency among the results is founded, which clearly shows that the method can be used for uranium determination in high salinity brine.%通过系统对比实验,建立了一种适合于盐湖水、晶间卤水等高矿化度液体样品中微量铀的测定方法——紫外荧光法.在确定仪器测量稳定性的基础上,给出紫外荧光法测定铀的最佳条件为样品pH=2~12,荧光增强剂用量为500μL.为减少杂质离子对铀测定的干扰,分别采用直接稀释荧光法及TBP萃取荧光法进行铀的测定,确定了TBP萃取荧光法测量高矿化度水样中微量铀的步

  18. Assessing Radium Activity in Shale Gas Produced Brine

    Science.gov (United States)

    Fan, W.; Hayes, K. F.; Ellis, B. R.

    2015-12-01

    The high volumes and salinity associated with shale gas produced water can make finding suitable storage or disposal options a challenge, especially when deep well brine disposal or recycling for additional well completions is not an option. In such cases, recovery of commodity salts from the high total dissolved solids (TDS) of the brine wastewater may be desirable, yet the elevated concentrations of the naturally occurring radionuclides such as Ra-226 and Ra-228 in produced waters (sometimes substantially greater than the EPA limit of 5 pCi/L) may concentrate during these steps and limit salt recovery options. Therefore, assessing the potential presence of these Ra radionuclides in produced water from shale gas reservoir properties is desirable. In this study, we seek to link U and Th content within a given shale reservoir to the expected Ra content of produced brine by accounting for secular equilibrium within the rock and subsequent release to Ra to native brines. Produced brine from a series of Antrim shale wells and flowback from a single Utica-Collingwood shale well in Michigan were sampled and analyzed via ICP-MS to measure Ra content. Gamma spectroscopy was used to verify the robustness of this new Ra analytical method. Ra concentrations were observed to be up to an order of magnitude higher in the Antrim flowback water samples compared to those collected from the Utica-Collingwood well. The higher Ra content in Antrim produced brines correlates well with higher U content in the Antrim (19 ppm) relative to the Utica-Collingwood (3.5 ppm). We also observed an increase in Ra activity with increasing TDS in the Antrim samples. This Ra-TDS relationship demonstrates the influence of competing divalent cations in controlling Ra mobility in these clay-rich reservoirs. In addition, we will present a survey of geochemical data from other shale gas plays in the U.S. correlating shale U, Th content with produced brine Ra content. A goal of this study is to develop a

  19. Geophysical and geochemical signatures of Gulf of Mexico seafloor brines

    Directory of Open Access Journals (Sweden)

    S. B. Joye

    2005-05-01

    Full Text Available Geophysical, temperature, and discrete depth-stratified geochemical data illustrate differences between an actively venting mud volcano and a relatively quiescent brine pool in the Gulf of Mexico along the continental slope. Geophysical data, including laser-line scan mosaics and sub-bottom profiles, document the dynamic nature of both environments. Temperature profiles, obtained by lowering a CTD into the brine fluid, show that the venting brine was at least 10°C warmer than the bottom water. At the brine pool, two thermoclines were observed, one directly below the brine-seawater interface and a second about one meter below the first. At the mud volcano, substantial temperature variability was observed, with the core brine temperature being either slightly (~2°C in 1997 or substantially (19°C in 1998 elevated above bottom water temperature. Geochemical samples were obtained using a device called the "brine trapper" and concentrations of dissolved gases, major ions and nutrients were determined using standard techniques. Both brines contained about four times as much salt as seawater and steep concentration gradients of dissolved ions and nutrients versus brine depth were apparent. Differences in the concentrations of calcium, magnesium and potassium between the two brine fluids suggests that the fluids are derived from different sources or that brine-sediment reactions are more important at the mud volcano than the brine pool. Substantial concentrations of methane and ammonium were observed in both brines, suggesting that fluids expelled from deep ocean brines are important sources of methane and dissolved inorganic nitrogen to the surrounding environment.

  20. Bioencapsulation of metronidazole in adult brine shrimp (Artemia sp.).

    Science.gov (United States)

    Allender, Matthew C; Kastura, Mike; George, Robert; Bulman, Frank; Yarbrough, Jason; Cox, Sherry

    2011-06-01

    A description of bioencapsulation of metronidazole in adult brine shrimp (Artemia) for 2.5 g/L, 5 g/L, and 10 g/L treatment baths is presented. Metronidazole was detected in adult brine shrimp tissue after enrichment periods of 15 min, 30 min, 1 hr, 2 hr, 4 hr, 8 hr, 12 hr, and 24 hr. The assays were performed using high performance liquid chromatography. There was a positive relationship in both dose and time. When evaluating percent uptake, all three baths demonstrated a similar pattern. All three bath concentrations had a high initial concentration that fell at 30 min and slowly began to increase through the end of the study. Survival of shrimp was not affected by bath concentration but decreased over time in all treatment baths comparatively. It can be concluded that metronidazole can be successfully bioencapsulated in adult Artemia.

  1. Methanotrophy and sulfate reduction at the interface between Mediterranean seawater and the MgCl2-dominated Kryos brine basin

    Science.gov (United States)

    Steinle, Lea; Felber, Nicole; Casalino, Claudia; de Lange, Gert J.; Lehmann, Moritz F.; Stadnitskaia, Alina; Sinninghe Damste, Jaap S.; Tessarolo, Chiara; Treude, Tina; Zopfi, Jakob; Niemann, Helge

    2014-05-01

    The Kryos brine basin is located at ˜3000m water depth in the Eastern Mediterranean Sea. The anoxic brine originates from subsurface Messinian evaporites and is dominated by very high concentrations of MgCl2-equivalents (˜5M), making this environment challenging for live. The strong density difference between the brine and the overlying Mediterranean seawater impedes mixing, and the seawater-brine interface is thus characterized by a strong redox gradient. In the redoxcline, we observed sharp sulfate, sulfide and methane concentration gradients, from seawater background concentrations to high concentrations in the brine (˜150 mM sulfate, ˜250 μM sulfide, ˜50 μM methane). Right at the interface, under micro-oxic conditions, we determined methane oxidation rates of up to 60 nM/day, and sulfate reduction rates of up to 15 μM/day. Our findings of 13C-depleted biomarkers typical for aerobic methanotrophs (diplopterol, fatty acid C16:1ω8) indicate an aerobic mode of methane oxidation independent of sulfate reduction. Below the interface (within the anoxic brine), the presence of both methane and sulfate would make the anaerobic oxidation of methane with sulfate (AOM) thermodynamically feasible. However, while sulfate reduction rates were very high (500 μM/day), methane oxidation rates were not detectable suggesting inhibition of AOM. In the brine, we detected high concentrations of an unusual fatty acid (10Me-C16:0) indicative for sulfate reducing bacteria, which might be responsible for the high sulfate reduction rates. In addition, we also found archaeal lipids (archaeol, PMI) moderately depleted in 13C. Considering the absence of AOM activity, these lipids suggest a methanogenic, rather than methanotrophic origin of the archaea within the brine. All these results provide new and exciting insight into life in an extreme environment.

  2. Numerical analysis of seawater circulation in carbonate platforms: II. The dynamic interaction between geothermal and brine reflux circulation

    Science.gov (United States)

    Jones, G.D.; Whitaker, F.F.; Smart, P.L.; Sanford, W.E.

    2004-01-01

    Density-driven seawater circulation may occur in carbonate platforms due to geothermal heating and / or reflux of water of elevated salinity. In geothermal circulation lateral contrasts in temperature between seawater and platform groundwaters warmed by the geothermal heat flux result in upward convective flow, with colder seawater drawn into the platform at depth. With reflux circulation, platform-top waters concentrated by evaporation flow downward, displacing less dense underlying groundwaters. We have used a variable density groundwater flow model to examine the pattern, magnitude and interaction of these two different circulation mechanisms, for mesosaline platform-top waters (50???) and brines concentrated up to saturation with respect to gypsum (150???) and halite (246???). Geothermal circulation, most active around the platform margin, becomes restricted and eventually shut-off by reflux of brines from the platform interior towards the margin. The persistence of geothermal circulation is dependent on the rate of brine reflux, which is proportional to the concentration of platform-top brines and also critically dependent on the magnitude and distribution of permeability. Low permeability evaporites can severely restrict reflux whereas high permeability units in hydraulic continuity enhance brine transport. Reduction in permeability with depth and anisotropy of permeability (kv < < kh) focuses flow laterally in the shallow subsurface (<1 km), resulting in a horizontally elongated brine plume. Aquifer porosity and dispersivity are relatively minor controls on reflux. Platform brines can entrain surficial seawater when brine generating conditions cease but the platform-top remains submerged, a variant of reflux we term "latent reflux". Brines concentrated up to gypsum saturation have relatively long residence times of at least 100 times the duration of the reflux event. They thus represent a long-term control on post-reflux groundwater circulation, and

  3. Lithium brines: A global perspective: Chapter 14

    Science.gov (United States)

    Munk, LeeAnn; Hynek, Scott; Bradley, Dwight C.; Boutt, David; Labay, Keith A.; Jochens, Hillary; Verplanck, Philip L.; Hitzman, Murray W.

    2016-01-01

    Lithium is a critical and technologically important element that has widespread use, particularly in batteries for hybrid cars and portable electronic devices. Global demand for lithium has been on the rise since the mid-1900s and is projected to continue to increase. Lithium is found in three main deposit types: (1) pegmatites, (2) continental brines, and (3) hydrothermally altered clays. Continental brines provide approximately three-fourths of the world’s Li production due to their relatively low production cost. The Li-rich brine systems addressed here share six common characteristics that provide clues to deposit genesis while also serving as exploration guidelines. These are as follows: (1) arid climate; (2) closed basin containing a salar (salt crust), a salt lake, or both; (3) associated igneous and/or geothermal activity; (4) tectonically driven subsidence; (5) suitable lithium sources; and (6) sufficient time to concentrate brine. Two detailed case studies of Li-rich brines are presented; one on the longest produced lithium brine at Clayton Valley, Nevada, and the other on the world’s largest producing lithium brine at the Salar de Atacama, Chile.

  4. Expected brine movement at potential nuclear waste repository salt sites

    Energy Technology Data Exchange (ETDEWEB)

    McCauley, V.S.; Raines, G.E.

    1987-08-01

    The BRINEMIG brine migration code predicts rates and quantities of brine migration to a waste package emplaced in a high-level nuclear waste repository in salt. The BRINEMIG code is an explicit time-marching finite-difference code that solves a mass balance equation and uses the Jenks equation to predict velocities of brine migration. Predictions were made for the seven potentially acceptable salt sites under consideration as locations for the first US high-level nuclear waste repository. Predicted total quantities of accumulated brine were on the order of 1 m/sup 3/ brine per waste package or less. Less brine accumulation is expected at domal salt sites because of the lower initial moisture contents relative to bedded salt sites. Less total accumulation of brine is predicted for spent fuel than for commercial high-level waste because of the lower temperatures generated by spent fuel. 11 refs., 36 figs., 29 tabs.

  5. The study of aluminium anodes for high power density Al/air batteries with brine electrolytes

    Science.gov (United States)

    Nestoridi, Maria; Pletcher, Derek; Wood, Robert J. K.; Wang, Shuncai; Jones, Richard L.; Stokes, Keith R.; Wilcock, Ian

    Aluminium alloys containing small additions of both tin (∼0.1 wt%) and gallium (∼0.05 wt%) are shown to dissolve anodically at high rates in sodium chloride media at room temperatures; current densities >0.2 A cm -2 can be obtained at potentials close to the open circuit potential, ∼-1500 mV versus SCE. The tin exists in the alloys as a second phase, typically as ∼1 μm inclusions (precipitates) distributed throughout the aluminium structure, and anodic dissolution occurs to form pits around the tin inclusions. Although the distribution of the gallium in the alloy could not be established, it is also shown to be critical in the formation of these pits as well as maintaining their activity. The stability of the alloys to open circuit corrosion and the overpotential for high rate dissolution, both critical to battery performance, are shown to depend on factors in addition to elemental composition; both heat treatment and mechanical working influence the performance of the alloy. The correlation between alloy performance and their microstructure has been investigated.

  6. The study of aluminium anodes for high power density Al/air batteries with brine electrolytes

    Energy Technology Data Exchange (ETDEWEB)

    Nestoridi, Maria; Pletcher, Derek [School of Chemistry, The University, Southampton SO19 1BJ (United Kingdom); Wood, Robert J.K.; Wang, Shuncai [School of Engineering Sciences, The University, Southampton SO19 1BJ (United Kingdom); Jones, Richard L.; Stokes, Keith R.; Wilcock, Ian [dstl, Physical Sciences Department, Porton Down, Salisbury, Wilts SP4 0JQ (United Kingdom)

    2008-03-15

    Aluminium alloys containing small additions of both tin ({proportional_to}0.1 wt%) and gallium ({proportional_to}0.05 wt%) are shown to dissolve anodically at high rates in sodium chloride media at room temperatures; current densities >0.2 A cm{sup -2} can be obtained at potentials close to the open circuit potential, {proportional_to}-1500 mV versus SCE. The tin exists in the alloys as a second phase, typically as {proportional_to}1 {mu}m inclusions (precipitates) distributed throughout the aluminium structure, and anodic dissolution occurs to form pits around the tin inclusions. Although the distribution of the gallium in the alloy could not be established, it is also shown to be critical in the formation of these pits as well as maintaining their activity. The stability of the alloys to open circuit corrosion and the overpotential for high rate dissolution, both critical to battery performance, are shown to depend on factors in addition to elemental composition; both heat treatment and mechanical working influence the performance of the alloy. The correlation between alloy performance and their microstructure has been investigated. (author)

  7. High-efficiency solar concentrator

    Science.gov (United States)

    Lansing, F. L.; Dorman, J.

    1980-01-01

    A new type of solar concentrator is presented using liquid lenses and simple translational tracking mechanism. The concentrator achieves a 100:1 nominal concentration ratio and is compared in performance with a flat-plate collector having two sheets of glazing and non-selective coating. The results of the thermal analysis show that higher temperatures can be obtained with the concentrator than is possible with the non-concentrator flat-plate type. Furthermore, the thermal efficiency far exceeds that of the comparative flat-plate type for all operating conditions.

  8. Selective oxidation of bromide in wastewater brines from hydraulic fracturing.

    Science.gov (United States)

    Sun, Mei; Lowry, Gregory V; Gregory, Kelvin B

    2013-07-01

    Brines generated from oil and natural gas production, including flowback water and produced water from hydraulic fracturing of shale gas, may contain elevated concentrations of bromide (~1 g/L). Bromide is a broad concern due to the potential for forming brominated disinfection byproducts (DBPs) during drinking water treatment. Conventional treatment processes for bromide removal is costly and not specific. Selective bromide removal is technically challenging due to the presence of other ions in the brine, especially chloride as high as 30-200 g/L. This study evaluates the ability of solid graphite electrodes to selectively oxidize bromide to bromine in flowback water and produced water from a shale gas operation in Southwestern PA. The bromine can then be outgassed from the solution and recovered, as a process well understood in the bromine industry. This study revealed that bromide may be selectively and rapidly removed from oil and gas brines (~10 h(-1) m(-2) for produced water and ~60 h(-1) m(-2) for flowback water). The electrolysis occurs with a current efficiency between 60 and 90%, and the estimated energy cost is ~6 kJ/g Br. These data are similar to those for the chlor-alkali process that is commonly used for chlorine gas and sodium hydroxide production. The results demonstrate that bromide may be selectively removed from oil and gas brines to create an opportunity for environmental protection and resource recovery.

  9. Aerobic methanotrophic communities at the Red Sea brine-seawater interface

    Directory of Open Access Journals (Sweden)

    Rehab Z. Abdallah

    2014-09-01

    Full Text Available The central rift of the Red Sea contains 25 brine pools with different physicochemical conditions, dictating the diversity and abundance of the microbial community. Three of these pools, the Atlantis II, Kebrit and Discovery Deeps, are uniquely characterized by a high concentration of hydrocarbons. The brine-seawater interface, described as an anoxic-oxic (brine-seawater boundary, is characterized by a high methane concentration, thus favoring aerobic methane oxidation. The current study analyzed the aerobic free–living methane-oxidizing bacterial communities that potentially contribute to methane oxidation at the brine-seawater interfaces of the three aforementioned brine pools, using metagenomic pyrosequencing, 16S rRNA pyrotags and pmoA library constructs. The sequencing of 16S rRNA pyrotags revealed that these interfaces are characterized by high microbial community diversity. Signatures of aerobic methane-oxidizing bacteria were detected in the Atlantis II Interface (ATII-I and the Kebrit Deep Upper (KB-U and Lower (KB-L brine-seawater interfaces. Through phylogenetic analysis of pmoA, we further demonstrated that the ATII-I aerobic methanotroph community is highly diverse. We propose four ATII-I pmoA clusters. Most importantly, cluster 2 groups with marine methane seep methanotrophs, and cluster 4 represent a unique lineage of an uncultured bacterium with divergent alkane monooxygenases. Moreover, non-metric multidimensional scaling (NMDS based on the ordination of putative enzymes involved in methane metabolism showed that the Kebrit interface layers were distinct from the ATII-I and DD-I brine-seawater interfaces.

  10. Results for the Brine Evaporation Bag (BEB) Brine Processing Test

    Science.gov (United States)

    Delzeit, Lance; Flynn, Michael; Fisher, John; Shaw, Hali; Kawashima, Brian; Beeler, David; Howard, Kevin

    2015-01-01

    The recent Brine Processing Test compared the NASA Forward Osmosis Brine Dewatering (FOBD), Paragon Ionomer Water Processor (IWP), UMPQUA Ultrasonic Brine Dewatering System (UBDS), and the NASA Brine Evaporation Bag (BEB). This paper reports the results of the BEB. The BEB was operated at 70 deg C and a base pressure of 12 torr. The BEB was operated in a batch mode, and processed 0.4L of brine per batch. Two different brine feeds were tested, a chromic acid-urine brine and a chromic acid-urine-hygiene mix brine. The chromic acid-urine brine, known as the ISS Alternate Pretreatment Brine, had an average processing rate of 95 mL/hr with a specific power of 5kWhr/L. The complete results of these tests will be reported within this paper.

  11. Fundamental study of the effect of high-salinity brines on the friction and wear properties of stainless steels

    Energy Technology Data Exchange (ETDEWEB)

    Pearsall, K.J.; Govin, G.; Eliezer, Z.; Bebout, D.G.; Bachman, A.L. (eds.)

    1981-01-01

    Friction and corrosive wear experiments were performed in a geothermal-geopressured brine and in a 3% NaCl solution in a friction and wear electrolytic cell. The formation of a passive film on 304 stainless steel has a beneficial effect on the magnitude of the coefficient of friction. When pits are electrochemically introduced in the passive film, the friction coefficient becomes even lower than the passive coefficient of friction in the 3% NaCl, but does not significantly change for the brine. The effect of corrosive wear on the surface film is more difficult to assess. Auger spectroscopy was performed on wear surfaces (subjected to both electrochemical and mechanical action) and non-wear surfaces (subjected only to electrochemical action). The surface films formed in 3% NaCl in the non-wear and wear areas including pits consisted of Cr, Fe and Ni in ratios consistent to the bulk material plus 0. In brine the surface film consists of the same elements as above; however, the surface film associated with the non-wear area and the wear area pit show a Cr depletion. Yet, the wear area film is consistent with bulk as in the case of the 3% NaCl.

  12. Geophysical and geochemical signatures of Gulf of Mexico seafloor brines

    Directory of Open Access Journals (Sweden)

    S. B. Joye

    2005-01-01

    Full Text Available Geophysical, temperature, and discrete depth-stratified geochemical data illustrate differences between an actively venting mud volcano and a relatively quiescent brine pool in the Gulf of Mexico along the continental slope. Geophysical data, including laser-line scan mosaics and sub-bottom profiles, document the dynamic nature of both environments. Temperature profiles, obtained by lowering a CTD into the brine fluid, show that the venting brine was at least 10°C warmer than the bottom water. At the brine pool, thermal stratification was observed and only small differences in stratification were documented between three sampling times (1991, 1997 and 1998. In contrast, at the mud volcano, substantial temperature variability was observed, with the core brine temperature being slightly higher than bottom water (by 2°C in 1997 but substantially higher than bottom water (by 19°C in 1998. Detailed geochemical samples were obtained in 2002 using a device called the 'brine trapper' and concentrations of dissolved gases, major ions and nutrients were determined. Both brines contained about four times as much salt as seawater and steep concentration gradients of dissolved ions and nutrients versus brine depth were apparent. Differences in the concentrations of calcium, magnesium and potassium between the two brine fluids suggest that the fluids are derived from different sources, have different dilution/mixing histories, or that brine-sediment reactions are more important at the mud volcano. Substantial concentrations of methane, ammonium, and silicate were observed in both brines, suggesting that fluids expelled from deep ocean brines are important sources of these constituents to the surrounding environment.

  13. Design Status of the Capillary Brine Residual in Containment Water Recovery System

    Science.gov (United States)

    Callahan, Michael R.; Sargusingh, Miriam

    2016-01-01

    One of the goals of the AES Life Support System (LSS) Project is to achieve 98% water loop closure for long duration human exploration missions beyond low Earth orbit. To meet this objective, the AES LSS Project is developing technologies to recover water from wastewater brine; highly concentrated waste products generated from a primary water recovery system. The state of the art system used aboard the International Space Station (ISS) has the potential to recover up to 85% water from unine wastewater, leaving a significant amounts of water in the waste brine, the recovery of which is a critical technology gap that must be filled in order to enable long duration human exploration. Recovering water from the urine wastewater brine is complicated by the concentration of solids as water is removed from the brine, and the concentration of the corrosive, toxic chemicals used to stabilize the urine which fouls and degrades water processing hardware, and poses a hazard to operators and crew. Brine Residual in Containment (BRIC) is focused on solids management through a process of "in-place" drying - the drying of brines within the container used for final disposal. Application of in-place drying has the potential to improve the safety and reliability of the system by reducing the exposure to crew and hardware to the problematic brine residual. Through a collaboration between the NASA Johnson Space Center and Portland Status University, a novel water recovery system was developed that utilizes containment geometry to support passive capillary flow and static phase separation allowing free surface evaporation to take place in a microgravity environment. A notional design for an ISS demonstration system was developed. This paper describes the concept for the system level design.

  14. Toxicological investigations of Aloe ferox Mill. extracts using Brine shrimp (Artemia salina L.) assay

    National Research Council Canada - National Science Library

    Abosede, Wintola Olubunmi; Sunday, Arowosegbe; Jide, Afolayan Anthony

    2015-01-01

    Cytotoxicity of the extracts of Aloe ferox using brine shrimp was evaluated. Effects of the extracts on hatchability and lethality of brine shrimps were reported in terms of minimum inhibitory concentration and LD(50) respectively...

  15. Genesis of underground brine along south coast of Laizhou Bay: hydrochemical characteristics

    Institute of Scientific and Technical Information of China (English)

    JIANG Xueyan; YU Zhigang; NING Jinsong; CHEN Hongtao; MI Tiezhu

    2006-01-01

    Hydrochemistry of underground brines along south coast of Laizhou Bay, Shandong, China has been analyzed. Brine samples were collected from 43 wells in this area. It was considered that the brines were originated from seawater. However, whether they were formed by seawater evaporation or seawater freezing was not fully sure. We created a simple method by plotting Na/Cl vs. seawater concentration factor (SCF) and Ca/Mg vs. SCF to determine the brine formation geochemically. Comparison of our results to previous seawater freezing and evaporation experiments indicated that the brines were formed by seawater evaporation. The ratios of HCO3/Cl of some low salinity brines in the study area were relatively higher, indicating that the brines may have mixed with other waters after the generation. The Br/Cl ratios of the brines decreased annually in the past 20 to 30 years of exploitation, indicating downward permeation of the brine from which bromine was extracted.

  16. Using fluorescence to characterize dissolved organic matter in Antarctic sea ice brines

    Science.gov (United States)

    Stedmon, Colin A.; Thomas, David N.; Papadimitriou, Stathys; Granskog, Mats A.; Dieckmann, Gerhard S.

    2011-09-01

    Sea ice plays a dynamic role in the air-sea exchange of CO2. In addition to abiotic inorganic carbon fluxes, an active microbial community produces and remineralizes organic carbon, which can accumulate in sea ice brines as dissolved organic matter (DOM). In this study, the characteristics of DOM fluorescence in Antarctic sea ice brines from the western Weddell Sea were investigated. Two humic-like components were identified, which were identical to those previously found to accumulate in the deep ocean and represent refractory material. Three amino-acid-like signals were found, one of which was unique to the brines and another that was spectrally very similar to tryptophan and found both in seawater and in brine samples. The tryptophan-like fluorescence in the brines exhibited intensities higher than could be explained by conservative behavior during the freezing of seawater. Its fluorescence was correlated with the accumulation of nitrogen-rich DOM to concentrations up to 900 μmol L-1 as dissolved organic carbon (DOC) and, thus, potentially represented proteins released by ice organisms. A second, nitrogen-poor DOM fraction also accumulated in the brines to concentrations up to 200 μmol L-1 but was not correlated with any of the fluorescence signals identified. Because of the high C:N ratio and lack of fluorescence, this material is thought to represent extracellular polymeric substances, which consist primarily of polysaccharides. The clear grouping of the DOM pool into either proteinaceous or carbohydrate-dominated material indicates that the production and accumulation of these two subpools of DOM in sea ice brines is, to some extent, decoupled.

  17. Application of a Re-Pd bimetallic catalyst for treatment of perchlorate in waste ion-exchange regenerant brine.

    Science.gov (United States)

    Liu, Jinyong; Choe, Jong Kwon; Sasnow, Zachary; Werth, Charles J; Strathmann, Timothy J

    2013-01-01

    Concentrated sodium chloride (NaCl) brines are often used to regenerate ion-exchange (IX) resins applied to treat drinking water sources contaminated with perchlorate (ClO(4)(-)), generating large volumes of contaminated waste brine. Chemical and biological processes for ClO(4)(-) reduction are often inhibited severely by high salt levels, making it difficult to recycle waste brines. Recent work demonstrated that novel rhenium-palladium bimetallic catalysts on activated carbon support (Re-Pd/C) can efficiently reduce ClO(4)(-) to chloride (Cl(-)) under acidic conditions, and here the applicability of the process for treating waste IX brines was examined. Experiments conducted in synthetic NaCl-only brine (6-12 wt%) showed higher Re-Pd/C catalyst activity than in comparable freshwater solutions, but the rate constant for ClO(4)(-) reduction measured in a real IX waste brine was found to be 65 times lower than in the synthetic NaCl brine. Through a series of experiments, co-contamination of the IX waste brine by excess NO(3)(-) (which the catalyst reduces principally to NH(4)(+)) was found to be the primary cause for deactivation of the Re-Pd/C catalyst, most likely by altering the immobilized Re component. Pre-treatment of NO(3)(-) using a different bimetallic catalyst (In-Pd/Al(2)O(3)) improved selectivity for N(2) over NH(4)(+) and enabled facile ClO(4)(-) reduction by the Re-Pd/C catalyst. Thus, sequential catalytic treatment may be a promising strategy for enabling reuse of waste IX brine containing NO(3)(-) and ClO(4)(-).

  18. Capillary pressure and saturation relations for supercritical CO2 and brine in sand: High-pressure Pc(Sw) controller/meter measurements and capillary scaling predictions

    Science.gov (United States)

    Tokunaga, Tetsu K.; Wan, Jiamin; Jung, Jong-Won; Kim, Tae Wook; Kim, Yongman; Dong, Wenming

    2013-08-01

    In geologic carbon sequestration, reliable predictions of CO2 storage require understanding the capillary behavior of supercritical (sc) CO2. Given the limited availability of measurements of the capillary pressure (Pc) dependence on water saturation (Sw) with scCO2 as the displacing fluid, simulations of CO2 sequestration commonly rely on modifying more familiar air/H2O and oil/H2O Pc(Sw) relations, adjusted to account for differences in interfacial tensions. In order to test such capillary scaling-based predictions, we developed a high-pressure Pc(Sw) controller/meter, allowing accurate Pc and Sw measurements. Drainage and imbibition processes were measured on quartz sand with scCO2-brine at pressures of 8.5 and 12.0 MPa (45°C), and air-brine at 21°C and 0.1 MPa. Drainage and rewetting at intermediate Sw levels shifted to Pc values that were from 30% to 90% lower than predicted based on interfacial tension changes. Augmenting interfacial tension-based predictions with differences in independently measured contact angles from different sources led to more similar scaled Pc(Sw) relations but still did not converge onto universal drainage and imbibition curves. Equilibrium capillary trapping of the nonwetting phases was determined for Pc = 0 during rewetting. The capillary-trapped volumes for scCO2 were significantly greater than for air. Given that the experiments were all conducted on a system with well-defined pore geometry (homogeneous sand), and that scCO2-brine interfacial tensions are fairly well constrained, we conclude that the observed deviations from scaling predictions resulted from scCO2-induced decreased wettability. Wettability alteration by scCO2 makes predicting hydraulic behavior more challenging than for less reactive fluids.

  19. Brines as Sources of Long-term Subsurface Contamination

    Science.gov (United States)

    Flowers, T. C.; Hunt, J. R.

    2004-12-01

    Concentrated salt solutions, i.e. brines, are source terms for environmental contaminants released into surface waters and groundwaters. Brines arise from both natural and industrial processes such as natural salt deposits, solid rocket fuel production, landfill leachates, nuclear fuel reprocessing, and acid rock drainage. Additionally, many of the in-situ remediation fluids that have been implemented at the pilot or the field scale are also classified as brines. While brines are miscible with water, mixing processes are slow in the subsurface and this constrains the dilution of contaminants present within brines and the delivery of remediation fluids to sites where reactions are needed. The mixing of brines during their vertical migration through aquifers is determined by aquifer permeability as well as differences in density and viscosity between the brine and the ambient groundwater. The stability criterion for brine displacement was predicted in 1952 by Hill and the resulting dispersion at the mixing front is quantified by a compilation of literature data and the acquisition of new experimental data. As brines sink through aquifers, they become emplaced in less accessible locations where mass transfer models predict that contaminants within brines are slowly released into flowing groundwater. For radioactive wastes and environmental contaminants with very low acceptable concentrations, groundwater quality can be impacted for decades. Field data from a cooling water disposal site suggest that a dense brine is likely still present as a source term 40 years after waste disposal was stopped. Overall, analysis of pollution sources, quantification of transport processes, generalization of laboratory data, and limited evaluation of field data indicate that brines represent long-term sources of groundwater contamination and that source control has not been seriously addressed.

  20. Lithium isotope geochemistry and origin of Canadian shield brines.

    Science.gov (United States)

    Bottomley, D J; Chan, L H; Katz, A; Starinsky, A; Clark, I D

    2003-01-01

    Hypersaline calcium/chloride shield brines are ubiquitous in Canada and areas of northern Europe. The major questions relating to these fluids are the origin of the solutes and the concentration mechanism that led to their extreme salinity. Many chemical and isotopic tracers are used to solve these questions. For example, lithium isotope systematics have been used recently to support a marine origin for the Yellowknife shield brine (Northwest Territories). While having important chemical similarities to the Yellowknife brine, shield brines from the Sudbury/Elliot Lake (Ontario) and Thompson/Snow Lake (Manitoba) regions, which are the focus of this study, exhibit contrasting lithium behavior. Brine from the Sudbury Victor mine has lithium concentrations that closely follow the sea water lithium-bromine concentration trajectory, as well as delta6Li values of approximately -28/1000. This indicates that the lithium in this brine is predominantly marine in origin with a relatively minor component of crustal lithium leached from the host rocks. In contrast, the Thompson/Snow Lake brine has anomalously low lithium concentrations, indicating that it has largely been removed from solution by alteration minerals. Furthermore, brine and nonbrine mine waters at the Thompson mine have large delta6Li variations of approximately 30/1000, which primarily reflects mixing between deep brine with delta6Li of -35 +/- 2/1000 and near surface mine water that has derived higher delta6Li values through interactions with their host rocks. The contrary behavior of lithium in these two brines shows that, in systems where it has behaved conservatively, lithium isotopes can distinguish brines derived from marine sources.

  1. Quantification of sub-resolution porosity in carbonate rocks by applying high-salinity contrast brine using X-ray microtomography differential imaging

    Science.gov (United States)

    Lin, Qingyang; Al-Khulaifi, Yousef; Blunt, Martin J.; Bijeljic, Branko

    2016-10-01

    Characterisation of the pore space in carbonate reservoirs and aquifers is of utmost importance in a number of applications such as enhanced oil recovery, geological carbon storage and contaminant transport. We present a new experimental methodology that uses high-salinity contrast brine and differential imaging acquired by X-ray tomography to non-invasively obtain three-dimensional spatially resolved information on porosity and connectivity of two rock samples, Portland and Estaillades limestones, including sub-resolution micro-porosity. We demonstrate that by injecting 30 wt% KI brine solution, a sufficiently high phase contrast can be achieved allowing accurate three-phase segmentation based on differential imaging. This results in spatially resolved maps of the solid grain phase, sub-resolution micro-pores within the grains, and macro-pores. The total porosity values from the three-phase segmentation for two carbonate rock samples are shown to be in good agreement with Helium porosity measurements. Furthermore, our flow-based method allows for an accurate estimate of pore connectivity and a distribution of porosity within the sub-resolution pores.

  2. Insertion sequences enrichment in extreme Red sea brine pool vent

    KAUST Repository

    Elbehery, Ali H. A.

    2016-12-03

    Mobile genetic elements are major agents of genome diversification and evolution. Limited studies addressed their characteristics, including abundance, and role in extreme habitats. One of the rare natural habitats exposed to multiple-extreme conditions, including high temperature, salinity and concentration of heavy metals, are the Red Sea brine pools. We assessed the abundance and distribution of different mobile genetic elements in four Red Sea brine pools including the world’s largest known multiple-extreme deep-sea environment, the Red Sea Atlantis II Deep. We report a gradient in the abundance of mobile genetic elements, dramatically increasing in the harshest environment of the pool. Additionally, we identified a strong association between the abundance of insertion sequences and extreme conditions, being highest in the harshest and deepest layer of the Red Sea Atlantis II Deep. Our comparative analyses of mobile genetic elements in secluded, extreme and relatively non-extreme environments, suggest that insertion sequences predominantly contribute to polyextremophiles genome plasticity.

  3. Modeling acid-gas generation from boiling chloride brines

    Directory of Open Access Journals (Sweden)

    Sonnenthal Eric

    2009-11-01

    Full Text Available Abstract Background This study investigates the generation of HCl and other acid gases from boiling calcium chloride dominated waters at atmospheric pressure, primarily using numerical modeling. The main focus of this investigation relates to the long-term geologic disposal of nuclear waste at Yucca Mountain, Nevada, where pore waters around waste-emplacement tunnels are expected to undergo boiling and evaporative concentration as a result of the heat released by spent nuclear fuel. Processes that are modeled include boiling of highly concentrated solutions, gas transport, and gas condensation accompanied by the dissociation of acid gases, causing low-pH condensate. Results Simple calculations are first carried out to evaluate condensate pH as a function of HCl gas fugacity and condensed water fraction for a vapor equilibrated with saturated calcium chloride brine at 50-150°C and 1 bar. The distillation of a calcium-chloride-dominated brine is then simulated with a reactive transport model using a brine composition representative of partially evaporated calcium-rich pore waters at Yucca Mountain. Results show a significant increase in boiling temperature from evaporative concentration, as well as low pH in condensates, particularly for dynamic systems where partial condensation takes place, which result in enrichment of HCl in condensates. These results are in qualitative agreement with experimental data from other studies. Conclusion The combination of reactive transport with multicomponent brine chemistry to study evaporation, boiling, and the potential for acid gas generation at the proposed Yucca Mountain repository is seen as an improvement relative to previously applied simpler batch evaporation models. This approach allows the evaluation of thermal, hydrological, and chemical (THC processes in a coupled manner, and modeling of settings much more relevant to actual field conditions than the distillation experiment considered. The actual

  4. Modeling acid-gas generation from boiling chloride brines

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Guoxiang; Spycher, Nicolas; Sonnenthal, Eric; Steefel, Carl

    2009-11-16

    This study investigates the generation of HCl and other acid gases from boiling calcium chloride dominated waters at atmospheric pressure, primarily using numerical modeling. The main focus of this investigation relates to the long-term geologic disposal of nuclear waste at Yucca Mountain, Nevada, where pore waters around waste-emplacement tunnels are expected to undergo boiling and evaporative concentration as a result of the heat released by spent nuclear fuel. Processes that are modeled include boiling of highly concentrated solutions, gas transport, and gas condensation accompanied by the dissociation of acid gases, causing low-pH condensate. Simple calculations are first carried out to evaluate condensate pH as a function of HCl gas fugacity and condensed water fraction for a vapor equilibrated with saturated calcium chloride brine at 50-150 C and 1 bar. The distillation of a calcium-chloride-dominated brine is then simulated with a reactive transport model using a brine composition representative of partially evaporated calcium-rich pore waters at Yucca Mountain. Results show a significant increase in boiling temperature from evaporative concentration, as well as low pH in condensates, particularly for dynamic systems where partial condensation takes place, which result in enrichment of HCl in condensates. These results are in qualitative agreement with experimental data from other studies. The combination of reactive transport with multicomponent brine chemistry to study evaporation, boiling, and the potential for acid gas generation at the proposed Yucca Mountain repository is seen as an improvement relative to previously applied simpler batch evaporation models. This approach allows the evaluation of thermal, hydrological, and chemical (THC) processes in a coupled manner, and modeling of settings much more relevant to actual field conditions than the distillation experiment considered. The actual and modeled distillation experiments do not represent

  5. Design and development of a high-concentration photovoltaic concentrator

    Energy Technology Data Exchange (ETDEWEB)

    Hodge, R C

    1982-04-01

    The design and development of a high concentration photovoltaic concentrator module is discussed. The design concept described herein incorporates a curved groove domed Fresnel lens, a high concentration etched multiple vertical junction (EMVJ) solar cell and a passively cooled direct-bonded copper cell mount all packaged in a plastic module. Two seven inch diameter 1200x domed Fresnel lenses were fabricated using single point diamond turning technology. Testing at both GE and Sandia confirmed optical transmission efficiencies of over 83%. Samples of the latest available EMVJ cells were mounted and installed, with a domed Fresnel lens, into a prototype module. Subsequent testing demonstrated net lens-cell efficiencies of 10 to 13%. As a result of this program, salient conclusions have been formulated as to this technology.

  6. Effects of copper, cadmium, and zinc on the hatching success of brine shrimp (Artemia franciscana).

    Science.gov (United States)

    Brix, K V; Gerdes, R M; Adams, W J; Grosell, M

    2006-11-01

    Previous studies indicate that the hatching success of brine shrimp (Artemia franciscana) cysts is surprisingly sensitive to ambient metal concentrations. These studies estimated median effective concentrations (EC50s) of 7, 5, and 28 microg l-1 for Cd, Cu, and Zn, suggesting that the hatching end point for A. franciscana is the most sensitive tested to date for Cd and Zn in saline environments and comparable in sensitivity with the most sensitive tested to date for Cu. Furthermore, these data suggest that brine shrimp are at significant risk from Cu and Zn in Great Salt Lake (GSL), UT, where ambient concentrations as high as 10 and 14 microg l-1, respectively, have been measured. Given that brine shrimp appear to be successfully reproducing in GSL, we hypothesized that these toxicity values were either biased low as a result of an artifact of the test method used or that site-specific water-quality conditions in the lake had decreased metal bioavailability such that brine shrimp could successfully reproduce. To test these hypotheses, we initiated a step-wise series of experiments. First we investigated the effects of pretreatment of brine shrimp cysts with antibiotics on brine shrimp sensitivity to metals because previous investigators as part of their test methods have used antibiotics. Next we considered the effect of ionic composition of the artificial test media on sensitivity. Finally, we evaluated the effects of the site-specific water quality of the GSL on metal bioavailability and toxicity. Results indicate that pretreatment of cysts with antibiotics had no effect on sensitivity. However, we were unable to repeat the previous values for Cd and Zn, obtaining EC50s of 11,859 and 289 microg l-1 for Cd and Zn, respectively. For Cu, however, we estimated an EC50 of 12 microg l-1, so we conducted further testing on the artificial media, adjusting the media composition to better reflect the Ca2+ and HCO3- concentration of normal seawater. This increased the EC50

  7. Treatment methods for geothermal brines

    Energy Technology Data Exchange (ETDEWEB)

    Phillips, S.L.; Mathur, A.K.; Garrison, W.

    1979-04-01

    A survey is made of commercially available methods currently in use as well as those which might be used to prevent scaling and corrosion in geothermal brines. More emphasis is placed on scaling. Treatments are classified as inhibitors, alterants and coagulants; they are applied to control scaling and corrosion in fresh and waste geothermal brines. Recommendations for research in brine treatment are described.

  8. Preliminary Feasibility Testing of the BRIC Brine Water Recovery Concept

    Science.gov (United States)

    Callahan, Michael R.; Pensinger, Stuart; Pickering, Karen D.

    2011-01-01

    The Brine Residual In-Containment (BRIC) concept was developed as a new technology to recover water from spacecraft wastewater brines. Such capability is considered critical to closing the water loop and achieving a sustained human presence in space. The intention of the BRIC concept is to increase the robustness and efficiency of the dewatering process by performing drying inside the container used for the final disposal of the residual brine solid. Recent efforts in the development of BRIC have focused on preliminary feasibility testing using a laboratory- assembled pre-prototype unit. Observations of the drying behavior of actual brine solutions processed under BRIC-like conditions has been of particular interest. To date, experiments conducted with three types of analogue spacecraft wastewater brines have confirmed the basic premise behind the proposed application of in-place drying for these solutions. Specifically, the dried residual mass from these solutions have tended to exhibit characteristics of adhesion and flow that are expected to continue to challenge process stream management in spacecraft brine dewatering system designs. Yet, these same characteristics may favor the development of capillary- and surface-tension-based approaches envisioned as part of an ultimate microgravity-compatible BRIC design. In addition, preliminary feasibility testing of the BRIC pre-prototype confirmed that high rates of water recovery, up to 98% of the available brine water, may be possible while still removing the majority of the brine contaminants from the influent brine stream. These and other observations from testing are reported.

  9. Evaluation of Brine Processing Technologies for Spacecraft Wastewater

    Science.gov (United States)

    Shaw, Hali L.; Flynn, Michael; Wisniewski, Richard; Lee, Jeffery; Jones, Harry; Delzeit, Lance; Shull, Sarah; Sargusingh, Miriam; Beeler, David; Howard, Jeanie; Howard, Kevin; Harris, Linden; Parodi, Jurek; Kawashima, Brian

    2015-01-01

    Brine drying systems may be used in spaceflight. There are several advantages to using brine processing technologies for long-duration human missions including a reduction in resupply requirements and achieving high water recovery ratios. The objective of this project was to evaluate four technologies for the drying of spacecraft water recycling system brine byproducts. The technologies tested were NASA's Forward Osmosis Brine Drying (FOBD), Paragon's Ionomer Water Processor (IWP), NASA's Brine Evaporation Bag (BEB) System, and UMPQUA's Ultrasonic Brine Dewatering System (UBDS). The purpose of this work was to evaluate the hardware using feed streams composed of brines similar to those generated on board the International Space Station (ISS) and future exploration missions. The brine formulations used for testing were the ISS Alternate Pretreatment and Solution 2 (Alt Pretreat). The brines were generated using the Wiped-film Rotating-disk (WFRD) evaporator, which is a vapor compression distillation system that is used to simulate the function of the ISS Urine Processor Assembly (UPA). Each system was evaluated based on the results from testing and Equivalent System Mass (ESM) calculations. A Quality Function Deployment (QFD) matrix was also developed as a method to compare the different technologies based on customer and engineering requirements.

  10. Uranium(VI) solubility in carbonate-free WIPP brine

    Energy Technology Data Exchange (ETDEWEB)

    Lucchini, J.F.; Borkowski, M.; Richmann, M.K.; Reed, D.T. [Los Alamos National Lab. (LANL), Carlsbad, NM (United States). Earth and Environmental Sciences Div.

    2013-08-01

    The solubility of uranium(VI) was determined in WIPP-relevant brines as a function of pC{sub H+} and ionic strength, in the absence of carbonate. Carbonate concentration was below 2 x 10{sup -5} M, measured using the gas chromatography method. In the absence of carbonate, the uranium(VI) solubilities were about x 10{sup -6} M in GWB at pC{sub H+} {>=} 7 and about 10{sup -8}-10{sup -7} M in ERDA-6 brine at pC{sub H+} {>=} 8. Solubility of uranium(VI) was also measured in NaCl media at the same levels as in ERDA-6 brine. The data established a uranium solubility that was 10-100 times lower than published results from Diaz-Arocas and Grambow, and they are in good agreement with modeling results and other literature data. In the absence of carbonate, hydrolysis was the main complexation and precipitation mechanisms for uranium(VI) solubility at high ionic strength and pC{sub H+} {>=} 7. However, the effect of borate complexation was noticeable at pC{sub H+} {proportional_to} 8-9. (orig.)

  11. Experimental Work Conducted on MgO Inundated Hydration in WIPP-Relevant Brines

    Science.gov (United States)

    Deng, H.; Xiong, Y.; Nemer, M. B.; Johnsen, S.

    2009-12-01

    -saturated Q-brine, a high-ionic-strength (up to 15 m) brine from Asse, Germany. We used EQ3/6 to simulate MgO hydration and carbonation in a closed system containing brine and CO2 at atmospheric concentration by titrating periclase into the system. (EQ3/6 is a geochemical software package for speciation, solubility calculations and reaction path modeling.) EQ3/6 predicted Mg and Cl concentrations and pH similar to the experimentally observed values. EQ3/6 also predicted hydration products similar to thsoe observed experimentally. * This research is funded by WIPP programs administered by the U.S. Department of Energy. ** Sandia is a multiprogram laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the United States Department of Energy’s National Nuclear Security Administration under contract DE-AC04-94AL85000.

  12. Trichloroethylene Volatilization Enhancement by the Addition of a Brine Solution

    Science.gov (United States)

    Irizarry, M. L.; Padilla, I. Y.

    2008-12-01

    Trichloroethylene (TCE) is one of the most widely detected organic contaminants at National Priority List (NPL) sites. In many sites, TCE is trapped as a dense non-aqueous phase liquid (DNAPL) in formations of low permeability, and serves as long-term source of contamination. Cost effective remediation technologies that can be applied to tight formations need to be developed. This study investigates the enhancement of TCE volatilization from unsaturated clayey soils by adding a NaCl brine solution. It is postulated that the overall effect of the brine solution causing structured water around soil particles, increased relative permeability, and increased fugacity into the vapor phase, is to enhance TCE volatilization. TCE removal through the soil vapor extraction (SVE) technique can then be enhanced. Preliminary experimental work involves the use of static and dynamic flux reactors, containing TCE, water and clay. NaCl brine solution is added at different concentrations to evaluate the effect on TCE concentrations and volatilization rates. In the static flux mode, vapor concentrations in the headspace of sealed reactors are measured after a two-day period. In the dynamic flux mode, air is swept through the headspace of the reactors and TCE vapor concentrations are measured over time. Plots relating static TCE vapor concentration to brine concentration are used to show the effect of brine concentrations on TCE fugacity. Temporal concentration distributions of TCE show the effect of brine on the rate of volatilization. Keywords: Trichloroethylene (TCE), Soil vapor extraction (SVE), clay

  13. Reactive-transport modeling of fly ash-wate-brines interactions from laboratory-scale column studies

    Science.gov (United States)

    Mbugua, John M.; Catherine Ngila, J.; Kindness, Andrew; Demlie, Molla

    Dynamic leaching tests are important studies that provide more insights into time-dependent leaching mechanisms of any given solid waste. Hydrogeochemical modeling using PHREEQC was applied for column modeling of two ash recipes and brines generated from South African coal utility plants, Sasol and Eskom. The modeling results were part of a larger ash-brine study aimed at acquiring knowledge on (i) quantification and characterization of the products formed when ash is in contact with wate-brines in different scenarios, (ii) the mineralogical changes associated with wate-brine-ash interactions over time, (iii) species concentration, and (iv) leaching and transport controlling factors. The column modeling was successfully identified and quantified as important reactive mineralogical phases controlling major, minor and trace elements' release. The pH of the solution was found to be a very important controlling factor in leaching chemistry. The highest mineralogical transformation took place in the first 10 days of ash contact with either water or brines, and within 0.1 m from the column inflow. Many of the major and trace elements Ca, Mg, Na, K, Sr, S(VI), Fe, are leached easily into water systems and their concentration fronts were high at the beginning (within 0.1 m from the column inflow and within the first 10 days) upon contact with the liquid phase. However, their concentration decreased with time until a steady state was reached. Modeling results also revealed that geochemical reactions taking place during ash-wate-brine interactions does affect the porosity of the ash, whereas the leaching processes lead to increased porosity. Besides supporting experimental data, modeling results gave predictive insights on leaching of elements which may directly impact on the environment, particularly ground water. These predictions will help develop scenarios and offer potential guide for future sustainable waste management practices as a way of addressing the co

  14. Mirabilite solubility in equilibrium sea ice brines

    Science.gov (United States)

    Butler, Benjamin Miles; Papadimitriou, Stathys; Santoro, Anna; Kennedy, Hilary

    2016-06-01

    The sea ice microstructure is permeated by brine channels and pockets that contain concentrated seawater-derived brine. Cooling the sea ice results in further formation of pure ice within these pockets as thermal equilibrium is attained, resulting in a smaller volume of increasingly concentrated residual brine. The coupled changes in temperature and ionic composition result in supersaturation of the brine with respect to mirabilite (Na2SO4·10H2O) at temperatures below -6.38 °C, which consequently precipitates within the sea ice microstructure. Here, mirabilite solubility in natural and synthetic seawater derived brines, representative of sea ice at thermal equilibrium, has been measured in laboratory experiments between 0.2 and -20.6 °C, and hence we present a detailed examination of mirabilite dynamics within the sea ice system. Below -6.38 °C mirabilite displays particularly large changes in solubility as the temperature decreases, and by -20.6 °C its precipitation results in 12.90% and 91.97% reductions in the total dissolved Na+ and SO42- concentrations respectively, compared to that of conservative seawater concentration. Such large non-conservative changes in brine composition could potentially impact upon the measurement of sea ice brine salinity and pH, whilst the altered osmotic conditions may create additional challenges for the sympagic organisms that inhabit the sea ice system. At temperatures above -6.38 °C, mirabilite again displays large changes in solubility that likely aid in impeding its identification in field samples of sea ice. Our solubility measurements display excellent agreement with that of the FREZCHEM model, which was therefore used to supplement our measurements to colder temperatures. Measured and modelled solubility data were incorporated into a 1D model for the growth of first-year Arctic sea ice. Model results ultimately suggest that mirabilite has a near ubiquitous presence in much of the sea ice on Earth, and illustrate the

  15. Experimental study of the stability and activity of brines on the surface of Mars

    Science.gov (United States)

    Altheide, Travis S.

    This work contributes to the understanding of liquid water stability, with an emphasis on the role that dissolved solutes may have had on liquid water formation on Mars, past and present. In chapter 2, the stability of liquid water under martian conditions is explored through experiments on ferric sulfate brines. First, it is demonstrated that such brines can be formed starting from typical martian mineralogy. Ferric sulfates are quite soluble, up to 48 wt%, and can form solutions which remain liquid down to 205 +/-1 K at the eutectic. As a result of low water activities, these solutions exhibit evaporation rates 20 times lower than pure water. The combination of a low eutectic point and low evaporation rates allow subsurface liquids to be stable at high martian latitudes, where the majority of gullies and viscous flow features are located. Thus, the characteristics of ferric sulfate brines were further investigated in chapter 3, where the viscous properties of such solutions were measured, with respect to changing temperature and concentration. Using these results, the viscosity of these solutions on the formation of gullies was considered, where calculated fluid flow velocities were found to be in accordance with some estimates from image analyses of gully formations. In chapter 4, other Mars-relevant brines were studied and characterized under martian surface conditions. Magnesium and ferrous sulfate, and magnesium and ferric chloride brines were found to stabilize water, through lower evaporation rates and freezing point depression, much like the ferric sulfate brines. For these sulfate brines, it was found that the thermodynamic process of phase change, i.e. ice formation and/or salt crystallization, can affect the kinetic process of evaporation, through very low water activities in solution. Furthermore, in chapter 5 these studies were extended to recent results from the Phoenix mission, by examining the stability of perchlorate brines under conditions

  16. Producing a highly concentrated coal suspension

    Energy Technology Data Exchange (ETDEWEB)

    Mokudzu, K.; Atsudzima, T.; Kiyedzuka, Y.

    1983-06-03

    Coal from wet and dry grinding is loaded into a mixer with a mixer arm with the acquisition of a highly concentrated suspension. Foamers (for instance, alkylbenzolsulfonate) and foam stabilizers (for instance diethanolamide of lauric acid) are added in a ratio of 10 to (2 to 5). The high fluidity of the suspension is maintained by injecting air into the suspension and an 80 percent concentration of the suspension is achieved.

  17. 多效膜蒸馏过程用于海水和浓海水的深度浓缩%Study on deep concentration of seawater and brine by multiple-effect membrane distillation

    Institute of Scientific and Technical Information of China (English)

    王奔; 秦英杰; 王彬; 靳军宝; 刘立强

    2013-01-01

    This paper studied the feasibility of multiple-effect membrane distillation(MEMD) with ion exchange in the process of desalination and deep-concentration of fresh seawater and brine from a desalination plant. The selective decalcification process could remove >90% of calcium ions , effectively preventing membrane fouling from CaSO4 precipitation in highly concentrated seawater. This research investigated the influences of various operational conditions on the performances of the MEMD process and evaluated permeate flux (J) , gained output ration (GOR) , and permeate conductivity. The experimental results showed that the maximum J and GOR were 6.07 L/(m2·h) and 13.2 respectively. When the decalcified seawater were concentrated to 250 g/L under optimized operational conditions,the electrical conductivity of the permeate was less than 200μm/cm,and J and GOR were up to 3.61 L/(m2·h) and 4.96 respectively. Two MEMD modules from different membranes demonstrated a long-term stability of at least 45 days,indicating the feasibility of this process for deep desalination of sweater.%研究了离子交换法选择性脱钙与多效膜蒸馏相结合用于海水淡化和淡化厂浓水深度浓缩的可行性。海水或浓海水中钙离子能脱除90%以上,可防止高倍数浓缩时海水中硫酸钙沉淀对膜造成污染。本文以膜通量、造水比和馏出液电导率为多效膜蒸馏过程的性能指标,研究了操作条件对过程性能的影响。膜通量最高可达6.07 L/(m2·h),造水比最高可达13.2;当海水浓缩至250 g/L时,馏出液的电导率小于200μm/cm,膜通量和造水比仍可达3.61 L/(m2·h)和4.96。以除钙后的浓海水为料液,利用两种多效膜蒸馏组件分别进行了持续45天的操作稳定性实验研究,在试验期间膜组件性能没有明显下降。该研究结果表明,多效膜蒸馏结合选择性脱钙是适合于海水深度浓缩及资源综合利用的高效节能技术。

  18. Diversity and distribution of eukaryotic microbes in and around a brine pool adjacent to the Thuwal cold seeps in the Red Sea

    KAUST Repository

    Wang, Yong

    2014-02-04

    A hypoxic/suboxic brine pool at a depth of about 850 m was discovered near the Thuwal cold seeps in the Red Sea. Filled with high concentrations of hydrogen sulfide and ammonia, such a brine pool might limit the spread of eukaryotic organisms. Here, we compared the communities of the eukaryotic microbes in a microbial mat, sediments and water samples distributed in 7 sites within and adjacent to the brine pool. Taxonomic classification of the pyrosequenced 18S rRNA amplicon reads showed that fungi highly similar to the species identified along the Arabic coast were almost ubiquitous in the water and sediment samples, supporting their wide distribution in various environments. The microbial mat displayed the highest species diversity and contained grazers and a considerable percentage of unclassified species. Phylogeny-based methods revealed novel lineages representing a majority of the reads from the interface between the sea water and brine pool. Phylogenetic relationships with more reference sequences suggest that the lineages were affiliated with novel Alveolata and Euglenozoa inhabiting the interface where chemosynthetic prokaryotes are highly proliferative due to the strong chemocline and halocline. The brine sediments harbored abundant species highly similar to invertebrate gregarine parasites identified in different oxygen-depleted sediments. Therefore, the present findings support the uniqueness of some microbial eukaryotic groups in this cold seep brine system. 2014 Wang, Zhang, Cao, Shek, Tian, Wong, Batang, Al-suwailem and Qian.

  19. Diversity and distribution of eukaryotic microbes in and around a brine pool adjacent to the Thuwal cold seeps in the Red Sea.

    Science.gov (United States)

    Wang, Yong; Zhang, Wei Peng; Cao, Hui Luo; Shek, Chun Shum; Tian, Ren Mao; Wong, Yue Him; Batang, Zenon; Al-Suwailem, Abdulaziz; Qian, Pei-Yuan

    2014-01-01

    A hypoxic/suboxic brine pool at a depth of about 850 m was discovered near the Thuwal cold seeps in the Red Sea. Filled with high concentrations of hydrogen sulfide and ammonia, such a brine pool might limit the spread of eukaryotic organisms. Here, we compared the communities of the eukaryotic microbes in a microbial mat, sediments and water samples distributed in 7 sites within and adjacent to the brine pool. Taxonomic classification of the pyrosequenced 18S rRNA amplicon reads showed that fungi highly similar to the species identified along the Arabic coast were almost ubiquitous in the water and sediment samples, supporting their wide distribution in various environments. The microbial mat displayed the highest species diversity and contained grazers and a considerable percentage of unclassified species. Phylogeny-based methods revealed novel lineages representing a majority of the reads from the interface between the sea water and brine pool. Phylogenetic relationships with more reference sequences suggest that the lineages were affiliated with novel Alveolata and Euglenozoa inhabiting the interface where chemosynthetic prokaryotes are highly proliferative due to the strong chemocline and halocline. The brine sediments harbored abundant species highly similar to invertebrate gregarine parasites identified in different oxygen-depleted sediments. Therefore, the present findings support the uniqueness of some microbial eukaryotic groups in this cold seep brine system.

  20. Diversity and distribution of eukaryotic microbes in and around a brine pool adjacent to the Thuwal cold seeps in the Red Sea

    Directory of Open Access Journals (Sweden)

    Yong eWang

    2014-02-01

    Full Text Available A hypoxic/suboxic brine pool at a depth of about 850 m was discovered near the Thuwal cold seeps in the Red Sea. Filled with high concentrations of hydrogen sulfide and ammonia, such a brine pool might limit the spread of eukaryotic organisms. Here, we compared the communities of the eukaryotic microbes in a microbial mat, sediments and water samples distributed in 7 sites within and adjacent to the brine pool. Taxonomic classification of the pyrosequenced 18S rRNA amplicon reads showed that fungi highly similar to the species identified along the Arabic coast were almost ubiquitous in the water and sediment samples, supporting their wide distribution in various environments. The microbial mat displayed the highest species diversity and contained grazers and a considerable percentage of unclassified species. Phylogeny-based methods revealed novel lineages representing a majority of the reads from the interface between the sea water and brine pool. Phylogenetic relationships with more reference sequences suggest that the lineages were affiliated with novel Alveolata and Euglenozoa inhabiting the interface where chemosynthetic prokaryotes are highly proliferative due to the strong chemocline and halocline. The brine sediments harbored abundant species highly similar to invertebrate gregarine parasites identified in different oxygen-depleted sediments. Therefore, the present findings support the uniqueness of some microbial eukaryotic groups in this cold seep brine system.

  1. Advanced oxidation of iodinated X-ray contrast media in reverse osmosis brines: the influence of quenching.

    Science.gov (United States)

    Azerrad, Sara P; Gur-Reznik, Shirra; Heller-Grossman, Lilly; Dosoretz, Carlos G

    2014-10-01

    Among the main restrictions for the implementation of advanced oxidation processes (AOPs) for removal of micropollutants present in reverse osmosis (RO) brines of secondary effluents account the quenching performed by background organic and inorganic constituents. Natural organic matter (NOM) and soluble microbial products (SMP) are the main effluent organic matter constituents. The inorganic fraction is largely constituted by chlorides and bicarbonate alkalinity with sodium and calcium as main counterions. The quenching influence of these components, separately and their mixture, in the transformation of model compounds by UVA/TiO2 was studied applying synthetic brines solutions mimicking 2-fold concentrated RO secondary effluents brines. The results were validated using fresh RO brines. Diatrizoate (DTZ) and iopromide (IOPr) were used as model compound. They have been found to exhibit relative high resistance to oxidation process and therefore represent good markers for AOPs techniques. Under the conditions applied, oxidization of DTZ in the background of RO brines was strongly affected by quenching effects. The major contribution to quenching resulted from organic matter (≈70%) followed by bicarbonate alkalinity (≈30%). NOM displayed higher quenching than SMP in spite of its relative lower concentration. Multivalent cations, i.e., Ca(+2), were found to decrease effectiveness of the technique due to agglomeration of the catalyst. However this influence was lowered in presence of NOM. Different patterns of transformation were found for each model compound in which a delayed deiodination was observed for iopromide whereas diatrizoate oxidation paralleled deiodination.

  2. Brines formed by multi-salt deliquescence

    Energy Technology Data Exchange (ETDEWEB)

    Carroll, S; Rard, J; Alai, M; Staggs, K

    2005-11-04

    The FY05 Waste Package Environment testing program at Lawrence Livermore National Laboratory focused on determining the temperature, relative humidity, and solution compositions of brines formed due to the deliquescence of NaCl-KNO{sub 3}-NaNO{sub 3} and NaCl-KNO{sub 3}-NaNO{sub 3}-Ca(NO{sub 3}){sub 2} salt mixtures. Understanding the physical and chemical behavior of these brines is important because they define conditions under which brines may react with waste canister surfaces. Boiling point experiments show that NaCl-KNO{sub 3}-NaNO{sub 3} and NaCl-KNO{sub 3}-NaNO{sub 3}-Ca(NO{sub 3}){sub 2} salt mixtures form brines that transform to hydrous melts that do not truly 'dry out' until temperatures exceed 300 and 400 C, respectively. Thus a conducting solution is present for these salt assemblages over the thermal history of the repository. The corresponding brines form at lower relative humidity at higher temperatures. The NaCl-KNO{sub 3}-NaNO{sub 3} salt mixture has a mutual deliquescence relative humidity (MDRH) of 25.9% at 120 C and 10.8% at 180 C. Similarly, the KNO{sub 3}-NaNO{sub 3} salt mixture has MDRH of 26.4% at 120 C and 20.0% at 150 C. The KNO{sub 3}-NaNO{sub 3} salt mixture salts also absorb some water (but do not appear to deliquesce) at 180 C and thus may also contribute to the transfer of electrons at interface between dust and the waste package surface. There is no experimental evidence to suggest that these brines will degas and form less deliquescent salt assemblages. Ammonium present in atmospheric and tunnel dust (as the chloride, nitrate, or sulfate) will readily decompose in the initial heating phase of the repository, and will affect subsequent behavior of the remaining salt mixture only through the removal of a stoichiometric equivalent of one or more anions. Although K-Na-NO{sub 3}-Cl brines form at high temperature and low relative humidity, these brines are dominated by nitrate, which is known to inhibit corrosion at lower

  3. Crystallographic structure of sea ice along a salinity gradient and environmental control of microalgae in the brine cells

    Science.gov (United States)

    Legendre, L.; Aota, M.; Shirasawa, K.; Martineau, M.-J.; Ishikawa, M.

    1991-08-01

    Duplicate ice cores were taken in southeastern Hudson Bay (Canadian Arctic), at 8 stations along a transect, from the mouth of the Great Whale River to saline waters 25 km offshore. One core from each station was cut into 10-cm sections, which were melted at room temperature for determinations of salinity, nutrients, algal pigments and taxonomic composition of the microalgal assemblages. On the second core, thin sections were cut every 2 cm to optically determine the ratio of brine/gas pockets to the total sections. Relative volumes of brine in melted samples were computed from the observed ratios and calculated values, and used to convert per unit brine volume the concentrations of pigments, nutrients and algal cells, initially measured per unit volume of melted sample. Salinity of the melted samples indicate the presence of freshwater beneath the sea ice close to shore throughout the growth season, and the vertical salinity profiles suggest intermittent intrusions of freshwater. Nutrient concentrations in the brine were high, suggesting that microalgae in the brine cells were generally not nutrient limited. Concentrations of ice algae in the brine cells reached relatively high values, that are often of the same order as those reported for eutrophic marine waters. Statistical analyses identified the rate of ice growth as the most important factor controlling the vertical and horizontal distributions of algal biomass and taxonomic composition in the sea ice, along the salinity gradient. Higher biomasses were generally associated with slower ice growth and also possibly lower grazing activity. In addition, the rate of ice growth influenced the distribution of microalgal assemblages, with nitrogen limitation potentially playing a secondary role in some instances.

  4. The Effect of Synthetic Brine Constituents on the Rate of Arsenic Release from Arsenopyrite

    Science.gov (United States)

    Parthasarathy, H.; Dzombak, D. A.; Karamalidis, A.

    2013-12-01

    Geologic carbon dioxide storage (GCS) in deep saline sedimentary formations is a potential method for mitigating increased levels of atmospheric CO2. Injection of CO2 in those formations may induce dissolution of reservoir minerals. Leakage of CO2-saturated brines and native brines could impact overlying drinking water aquifers by contaminating them with toxic constituents. Of particular concern is the effect of CO2 on the rates of dissolution of arsenic and other toxic metals from reservoir minerals. The most common pure phase arsenic mineral in sedimentary geologic formations is arsenopyrite (FeAsS). Natural brines have high salinities (up to 7M), with high concentrations of Na+, Ca2+, Mg2+ and K+. The focus of this study is to examine the effect of brine components on the dissolution rate of arsenic from arsenopyrite. A small-scale flow-through column system was constructed for this purpose and is being used to measure arsenic release rates from arsenopyrite. Influent solutions of NaCl, CaCl2, and MgCl2 at equal ionic strengths were used to examine the effect of the cationic species. A cleaning procedure to remove prior surface oxidation on the surface of the arsenopyrite particles was also developed. Preliminary results with NaCl and CaCl2 at an ionic strength of 0.011M indicate that the rate of dissolution of arsenic is dependent on the cationic species but independent of ionic strength.

  5. FIELD IMPLEMENTATION PLAN FOR A WILLISTON BASIN BRINE EXTRACTION AND STORAGE TEST

    Energy Technology Data Exchange (ETDEWEB)

    Hamling, John; Klapperich, Ryan; Stepan, Daniel; Sorensen, James; Pekot, Lawrence; Peck, Wesley; Jacobson, Lonny; Bosshart, Nicholas; Hurley, John; Wilson, William; Kurz, Marc; Burnison, Shaughn; Salako, Olarinre; Musich, Mark; Botnen, Barry; Kalenze, Nicholas; Ayash, Scott; Ge, Jun; Jiang, Tao; Dalkhaa, Chantsalmaa; Oster, Benjamin; Peterson, Kyle; Feole, Ian; Gorecki, Charles; Steadman, Edward

    2016-03-31

    extraction and injection wells were selected during the Phase I efforts. These wells will be permitted as North Dakota Administrative Code Underground Injection Control Class II wells and will yield additional characterization data which will further refine the FIP in Phase II. An array of surface and downhole monitoring techniques will validate ARM performance against predictive simulation results. Infrastructure will be constructed to manage extracted fluids at the surface and provide brine to a treatment test bed facility. Treatment of extracted brine can provide a means of reducing extracted brine disposal volumes, an alternate source of water, and/or salable products for beneficial use. A test bed facility will be constructed to provide a means of demonstrating these technologies on a wide range of brine concentrations. Screening criteria based on a techno-economic and life cycle assessment were developed to select high-salinity brine treatment technologies for extended duration treatment (30–60 days) in Phase II. A detailed cost assessment determined total implementation costs for BEST of $19,901,065 million (DOE share $15,680,505). These costs are inclusive of all necessary equipment, infrastructure construction, operations and project closeout costs required to implement BEST. An ideal combination of key factors makes the Johnsons Corner site uniquely suited to be the BEST demonstration.

  6. Cellulase Inhibition by High Concentrations of Monosaccharides

    DEFF Research Database (Denmark)

    Hsieh, Chia-Wen; Cannella, David; Jørgensen, Henning

    2014-01-01

    that low free water availability contributes to cellulase inhibition. Of the hydrolytic enzymes involved, those acting on the cellulose substrate, that is, exo- and endoglucanases, were the most inhibited. The β -glucosidases were shown to be less sensitive to high monosaccharide concentrations except...

  7. High-dimensional entanglement concentration of twisted photon pairs High-dimensional entanglement concentration

    Science.gov (United States)

    Chen, L. X.; Wu, Q. P.

    2012-10-01

    Recently, Dada et al. reported on the experimental entanglement concentration and violation of generalized Bell inequalities with orbital angular momentum (OAM) [Nat. Phys. 7, 677 (2011)]. Here we demonstrate that the high-dimensional entanglement concentration can be performed in arbitrary OAM subspaces with selectivity. Instead of violating the generalized Bell inequalities, the working principle of present entanglement concentration is visualized by the biphoton OAM Klyshko picture, and its good performance is confirmed and quantified through the experimental Shannon dimensionalities after concentration.

  8. Microprobe analysis of brine shrimp grown on meteorite extracts

    Energy Technology Data Exchange (ETDEWEB)

    Kennedy, J. [National Isotope Centre, GNS Science, 30 Gracefield Road, Lower Hutt (New Zealand)]. E-mail: j.kennedy@gns.cri.nz; Mautner, M.N. [Soil, Plant and Ecological Sciences Division, Lincoln University (New Zealand) and Department of Chemistry, University of Canterbury, Christchurch 8001 (New Zealand)]. E-mail: m.mautner@solis1.com; Barry, B. [National Isotope Centre, GNS Science, 30 Gracefield Road, Lower Hutt (New Zealand); Markwitz, A. [National Isotope Centre, GNS Science, 30 Gracefield Road, Lower Hutt (New Zealand)

    2007-07-15

    Nuclear microprobe methods have been used to investigate the uptake and distribution of various elements by brine shrimps and their unhatched eggs when grown in extracts of the Murchison and Allende carbonaceous meteorites, which were selected as model space resources. Measurements were carried out using a focussed 2 MeV proton beam raster scanned over the samples in order to obtain the average elemental concentrations. Line scans across the egg and shrimp samples show uptake of elements such as Mg, Ni, S and P which are present in the meteorites. The results confirmed that carbonaceous chondrite materials can provide nutrients, including high levels of the essential nutrient phosphate. The concentrations of these elements varied significantly between shrimp and eggs grown in extracts of the two meteorite types, which can help in identifying optimal growth media. Our results illustrate that nuclear microprobe techniques can determine elemental concentrations in organisms exposed to meteorite derived media and thus help in identifying useful future resources.

  9. Extreme Red Sea: Life in the deep-sea anoxic brine lakes

    OpenAIRE

    2013-01-01

    Tectonic splitting of the Arabian and African plates originated the Red Sea together with one of the most unique, remote, and extreme environments on Earth: deep-sea anoxic brine lakes. They combine multiple extremes namely increased salinity (7-fold), temperature (up to 70°C), concentration of heavy metals (1,000- to 10,000-fold), and hydrostatic pressure [1]. Despite such harsh conditions, they harbor an unexpectedly high biodiversity and are teeming with life. Increased i...

  10. Tolerance to cadmium and cadmium-binding ligands in Great Salt Lake brine shrimp (Artemia salina)

    Energy Technology Data Exchange (ETDEWEB)

    Jayasekara, S.; Drown, D.B.; Sharma, R.P.

    1986-02-01

    Information on the accumulation of cadmium in cytosolic proteins of Great Lake brine shrimp (Artemia salina) was obtained from animals collected directly from the lake and also from animal hatched and maintained in three sublethal concentrations of cadmium (0.5, 2.0, 5.0 ppm) in saltwater aquaria. Brine shrimp growth under these conditions was monitored by measuring body lengths during a 7-day exposure period. Heat-stable, cadmium-binding ligands were isolated and identified by Sephadex G-75 chromatography and atomic absorption spectrophotometry. Cadmium was found to be equally distributed between high and low molecular weight proteins in animals collected from the lake and the 0.5 ppm cadmium group. There was also a slight growth stimulation noted in the 0.5-pm group. Higher cadmium incorporation was noted in low molecular weight fractions with increasing cadmium concentration in the exposure media. Low molecular weight fractions were also found to have high uv absorption characteristics at 250 nm and low absorption at 280 nm. Molecular weight of the cadmium-binding ligands was found to be 11,000 as estimated by the gel filtration method. De novo synthesis of this protein was increased as a function of cadmium concentration in the media. However, slow accumulation of cadmium in other protein fractions was also noticed in higher cadmium exposure groups, suggesting the existence of possible tolerance mechanisms in brine shrimp exposed to suspected acute cadmium concentrations.

  11. Geochemical implications of brine leakage into freshwater aquifers.

    Science.gov (United States)

    Wunsch, Assaf; Navarre-Sitchler, Alexis K; McCray, John E

    2013-01-01

    CO(2) injection into deep saline formations as a way to mitigate climate change raises concerns that leakage of saline waters from the injection formations will impact water quality of overlying aquifers, especially underground sources of drinking water (USDWs). This paper aims to characterize the geochemical composition of deep brines, with a focus on constituents that pose a human health risk and are regulated by the U.S. Environmental Protection Agency (USEPA). A statistical analysis of the NATCARB brine database, combined with simple mixing model calculations, show total dissolved solids and concentrations of chloride, boron, arsenic, sulfate, nitrate, iron and manganese may exceed plant tolerance or regulatory levels. Twelve agricultural crops evaluated for decreased productivity in the event of brine leakage would experience some yield reduction due to increased TDS at brine-USDW ratios of United States are almost three times higher than public and domestic withdrawals.

  12. 煤制烯烃浓盐水处理回用难点及工艺技术选择%Difficulties and Selection of Technologies for Treatment and Reuse of Concentrated Brine in Coal to Olefin Industry

    Institute of Scientific and Technical Information of China (English)

    万大军

    2015-01-01

    In view of the difficult points of treatment and reuse of the concentrated brine from CTO reverse osmosis, several feasible technical solutions have been put forward and studied. As a result, the combined processing of EDR and the bioaugmentation technique has more advantages. This paper expounds the many difficulties of “Wastewater Zero Discharge” in coal chemical industry. It illustrates that the separation salt and resource utilization will be development direction in the future.%针对煤制烯烃RO浓盐水具有低可生化性、高结垢离子的处理难点,提出并研究对比了各种可行的浓盐水处理工艺方案,结果表明以EDR和生物强化技术的组合工艺更具有优势。同时,阐述了废水零排放实现面临的诸多困难,指出分盐处理及资源化利用将是未来发展方向。

  13. Microbial changes and growth of Listeria monocytogenes during chilled storage of brined shrimp (Pandalus borealis).

    Science.gov (United States)

    Mejlholm, Ole; Kjeldgaard, Jette; Modberg, Anne; Vest, Mette Bohn; Bøknaes, Niels; Koort, Joanna; Björkroth, Johanna; Dalgaard, Paw

    2008-06-10

    Thirteen storage trials and ten challenge tests were carried out to examine microbial changes, spoilage and the potential growth of Listeria monocytogenes in brined shrimp (Pandalus borealis). Shrimp in brine as well as brined and drained shrimp in modified atmosphere packaging (MAP) were produced and studied. Different recipes were used to study the effect of preserving parameters (organic acids, pH and NaCl) on growth of microorganisms and shelf life at 7-8 degrees C or 12 degrees C. Particularly, brines with different concentrations of (i) benzoic, citric and sorbic acids or (ii) acetic, citric and lactic acids were studied. Furthermore, the effect of adding diacetate to brined shrimp was evaluated. A single batch of cooked and peeled shrimp was used to study both industrially and manually processed brined shrimp with respect to the effect of process hygiene on microbial changes and the shelf life of products. Concentrations of microorganisms on newly produced brined shrimp from an industrial scale processing line were 1.0-2.3 log (CFU g(-1)) higher than comparable concentrations in manually processed samples. This resulted in a substantially shorter shelf life and a more diverse spoilage microflora of the industrially processed brined shrimp. In addition, shelf life of brined shrimp was affected by the types and concentrations of organic acids and by the storage temperature as expected. The effect of MAP was less pronounced. Eighty-two isolates from the spoilage microflora of brined shrimp were identified and they included 53 lactic acid bacteria, 6 coagulase negative Staphylococcus spp., 18 Pseudomonas fluorescens and 5 yeast isolates. After storage at 7 degrees C, P. fluorescens, Enterococcus-like isolates, E. malodoratus, Carnobacterium maltaromaticum, coagulase negative Staphylococcus spp. and Lactobacillus sakei constituted the dominating microflora of shrimp in brines that contained benzoic, citric and sorbic acids as preservatives. L. sakei dominated the

  14. Molds in Brined Cucumbers: Cause of Softening During Air-Purging of Fermentations †

    Science.gov (United States)

    Costilow, Ralph N.; Gates, Karen; Lacy, Melvyn L.

    1980-01-01

    Softening of cucumbers in fermentations purged at high air-flow rates was caused by molds growing in the brined cucumbers, not in the brine. This conclusion is based on the following results: (i) no microorganisms were isolated in significant numbers from brines that caused softening of pasteurized brined cucumbers, (ii) no pectinolytic enzyme activities were produced in cucumber brines in the absence of cucumbers, (iii) the pickles in some air-purged fermentations became very soft without the appearance of any pectinolytic enzyme activity in the brine, (iv) mold hyphae were consistently observed in tissues of soft pickles, (v) molds consistently developed in cultures of slices of surface sterilized cucumbers taken from fermentations in which soft pickles were subsequently found, and (vi) molds belonging to the genera Alternaria, Fusarium, and Mucor isolated from slices all softened pasteurized brined cucumbers. Images PMID:16345619

  15. Microbial changes and growth of Listeria monocytogenes during chilled storage of brined shrimp ( Pandalus borealis )

    DEFF Research Database (Denmark)

    Mejlholm, Ole; Kjeldgaard, J.; Modberg, A.

    2008-01-01

    Thirteen storage trials and ten challenge tests were carried out to examine microbial changes, spoilage and the potential growth of Listeria monocytogenes in brined shrimp (Pandalus borealis). Shrimp in brine as well as brined and drained shrimp in modified atmosphere packaging (MAP) were produced...... and lactic acids were studied. Furthermore, the effect of adding diacetate to brined shrimp was evaluated. A single batch of cooked and peeled shrimp was used to study both industrially and manually processed brined shrimp with respect to the effect of process hygiene on microbial changes and the shelf life...... of products. Concentrations of microorganisms on newly produced brined shrimp from an industrial scale processing line were 1.0-2.3 log (CFU g(-1)) higher than comparable concentrations in manually processed samples. This resulted in a substantially shorter shelf life and a more diverse spoilage microflora...

  16. Study on the Separation of Concentrated Brine with Nanofiltration Membrane%浓海水纳滤膜分离实验研究

    Institute of Scientific and Technical Information of China (English)

    周秀云; 付静怡; 陈侠

    2012-01-01

    采用美国海德能公司ESNA1 - LF - 4040纳滤膜,在不同温度、压力等操作条件下,对海水淡化浓海水进行了分离实验研究.实验结果表明:操作压力提高,膜通量增大的同时截留率也略有提高;料液温度上升,膜通量增大但截留率下降;在操作压力为1.4 MPa,料液温度为28℃时该纳滤膜对浓海水中一价离子(Na+、Cl-、K+)的截留率均小于15%,对二价离子(Ca2+、Mg2+、SO42-)的截留率均大于35%,其中对 的截留率可达97%以上,从而为纳滤膜在浓海水中的综合利用提供了可行的工艺参数.%The nanofiltration membrane ESNA1 - LF - 4040 made by Hydranautics company of American is employed in this study. The experimental research on the separation of concentrated seawater is done under different operation conditions, such as temperature, pressure and so on. It is shown that the membrane flux and rejection rate will increase when increasing the operation pressure ; and if increase the operation temperate, the membrane flux will increase, but the rejection rate will decrease- Under the optimal operation condition of L4MPa and 28℃, the rejection rate of monovalent ions (Na+ , Cl- , K+ ) is less than 15% and the rejection rate of divalent ions (Ca2+ , Mg + , SO4- ) is more than 35% , and the rejection rate of SO4- is more than 97%. The experimental result will supply reasonable processing parameter for the further application of nanofiltration membrane in the separation of the concentrated seawater.

  17. Enhanced Brine Dewatering System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The purpose of the Enhanced Brine Dewatering System (EBDS) is to provide a scalable means of completely recovering usable water from byproducts created by reverse...

  18. Membrane Cells for Brine Electrolysis.

    Science.gov (United States)

    Tingle, M.

    1982-01-01

    Membrane cells were developed as alternatives to mercury and diaphragm cells for the electrolysis of brine. Compares the three types of cells, focusing on the advantages and disadvantages of membrane cells. (JN)

  19. Membrane Cells for Brine Electrolysis.

    Science.gov (United States)

    Tingle, M.

    1982-01-01

    Membrane cells were developed as alternatives to mercury and diaphragm cells for the electrolysis of brine. Compares the three types of cells, focusing on the advantages and disadvantages of membrane cells. (JN)

  20. Enhanced Brine Dewatering System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The purpose of the Enhanced Brine Dewatering System (EBDS) is to provide an easily scalable means of completely recovering usable water from byproducts created by...

  1. Development of the brine shrimp Artemia is accelerated during spaceflight

    Science.gov (United States)

    Spooner, B. S.; Metcalf, J.; DeBell, L.; Paulsen, A.; Noren, W.; Guikema, J. A.

    1994-01-01

    Developmentally arrested brine shrimp cysts have been reactivated during orbital spaceflight on two different Space Shuttle missions (STS-50 and STS-54), and their subsequent development has been compared with that of simultaneously reactivated ground controls. Flight and control brine shrimp do not significantly differ with respect to hatching rates or larval morphology at the scanning and transmission EM levels. A small percentage of the flight larvae had defective nauplier eye development, but the observation was not statistically significant. However, in three different experiments on two different flights, involving a total of 232 larvae that developed in space, a highly significant difference in degree of flight to control development was found. By as early as 2.25 days after reactivation of development, spaceflight brine shrimp were accelerated, by a full instar, over ground control brine shrimp. Although developing more rapidly, flight shrimp grew as long as control shrimp at each developmental instar or stage.

  2. Density-driven free-convection model for isotopically fractionated geogenic nitrate in sabkha brine

    Science.gov (United States)

    Wood, Warren W.; Böhlke, John Karl

    2017-01-01

    Subsurface brines with high nitrate (NO3−) concentration are common in desert environments as atmospheric nitrogen is concentrated by the evaporation of precipitation and little nitrogen uptake. However, in addition to having an elevated mean concentration of ∼525 mg/L (as N), NO3− in the coastal sabkhas of Abu Dhabi is enriched in 15N (mean δ15N ∼17‰), which is an enigma. A NO3− solute mass balance analysis of the sabkha aquifer system suggests that more than 90% of the nitrogen is from local atmospheric deposition and the remainder from ascending brine. In contrast, isotopic mass balances based on Δ17O, δ15N, and δ18O data suggest approximately 80 to 90% of the NO3− could be from ascending brine. As the sabkha has essentially no soil, no vegetation, and no anthropogenic land or water use, we propose to resolve this apparent contradiction with a density-driven free-convection transport model. In this conceptual model, the density of rain is increased by solution of surface salts, transporting near-surface oxygenated NO3− bearing water downward where it encounters reducing conditions and mixes with oxygen-free ascending geologic brines. In this environment, NO3− is partially reduced to nitrogen gas (N2), thus enriching the remaining NO3− in heavy isotopes. The isotopically fractionated NO3− and nitrogen gas return to the near-surface oxidizing environment on the upward displacement leg of the free-convection cycle, where the nitrogen gas is released to the atmosphere and new NO3− is added to the system from atmospheric deposition. This recharge/recycling process has operated over many cycles in the 8000-year history of the shallow aquifer, progressively concentrating and isotopically fractionating the NO3−.

  3. t-BAMBP萃取分离高钾钠卤水中的铷工艺研究%Extraction and separation of rubidium from high potassium and sodium contained brine using t-BAMBP

    Institute of Scientific and Technical Information of China (English)

    杨少华; 赖晓晖; 王君; 王浩然; 谢宝如

    2015-01-01

    以二甲苯为稀释剂的t-BAMBP萃取体系,从高钾钠卤水中萃取分离铷.研究有机相配比、料液碱度、相比、萃取时间及萃取温度对萃取分离铷效果的影响.结果表明:在有机相组成(体积分数)为30%t-BAMBP+70% 二甲苯,料液Rb+初始浓度为0.011 7 mol/L,料液碱度为0.4 mol/L,相比VO/VA (有机相体积比水相体积)为1/1,萃取时间为4 min,萃取温度为21℃的条件下,经过五级逆流萃取,铷萃取率达95.5%.通过对料液进行多段萃取处理,可获得高纯度的铷盐.%T-BAMBP extraction system with xylene as diluent was applied to separate rubidium from brine containing high potassium and sodium. The influences of organic phase composition, feed liquid alkalinity, organic-aqueous phase ratio, extraction time and temperature on extraction and separation efficiency were investigated. The results show that extraction rate of rubidium after five staged countercurrent extraction reaches 95.5 % using 30 % volume fraction t-BAMBP contained organic extractant with 0.4 mol/L feed liquid alkalinity, 0.011 7 mol/L initial concentration of Rb +, 1:1 phase ratio, 4 min extraction time and 21 ℃extraction temperature. Highly purified rubidium salt can be obtained through multistage extraction.

  4. Diverse microbial species survive high ammonia concentrations

    Science.gov (United States)

    Kelly, Laura C.; Cockell, Charles S.; Summers, Stephen

    2012-04-01

    Planetary protection regulations are in place to control the contamination of planets and moons with terrestrial micro-organisms in order to avoid jeopardizing future scientific investigations relating to the search for life. One environmental chemical factor of relevance in extraterrestrial environments, specifically in the moons of the outer solar system, is ammonia (NH3). Ammonia is known to be highly toxic to micro-organisms and may disrupt proton motive force, interfere with cellular redox reactions or cause an increase of cell pH. To test the survival potential of terrestrial micro-organisms exposed to such cold, ammonia-rich environments, and to judge whether current planetary protection regulations are sufficient, soil samples were exposed to concentrations of NH3 from 5 to 35% (v/v) at -80°C and room temperature for periods up to 11 months. Following exposure to 35% NH3, diverse spore-forming taxa survived, including representatives of the Firmicutes (Bacillus, Sporosarcina, Viridibacillus, Paenibacillus, Staphylococcus and Brevibacillus) and Actinobacteria (Streptomyces). Non-spore forming organisms also survived, including Proteobacteria (Pseudomonas) and Actinobacteria (Arthrobacter) that are known to have environmentally resistant resting states. Clostridium spp. were isolated from the exposed soil under anaerobic culture. High NH3 was shown to cause a reduction in viability of spores over time, but spore morphology was not visibly altered. In addition to its implications for planetary protection, these data show that a large number of bacteria, potentially including spore-forming pathogens, but also environmentally resistant non-spore-formers, can survive high ammonia concentrations.

  5. Aromatic hydrocarbons associated with brines from geopressured wells

    Energy Technology Data Exchange (ETDEWEB)

    1992-09-01

    The various operational wells were sampled on a monthly basis for the yield of the cryocondensate hydrocarbons. The total cryocondensate concentration as well as the concentrations in the brine and the gas after passing the separator system are summarized. The total cryocondensate yield is displayed.

  6. Distinguishing seawater from geologic brine in saline coastal groundwater using radium-226; an example from the Sabkha of the UAE

    Science.gov (United States)

    Kraemer, Thomas F.; Wood, Warren W.; Sanford, Ward E.

    2014-01-01

    Sabkhat (Salt flats) are common geographic features of low-lying marine coastal areas that develop under hyper-arid climatic conditions. They are characterized by the presence of highly concentrated saline solutions and evaporitic minerals, and have been cited in the geologic literature as present-day representations of hyper-arid regional paleohydrogeology, paleoclimatology, coastal processes, and sedimentation in the geologic record. It is therefore important that a correct understanding of the origin and development of these features be achieved. Knowledge of the source of solutes is an important first step in understanding these features. Historically, two theories have been advanced as to the main source of solutes in sabkha brines: an early concept entailing seawater as the obvious source, and a more recent and dynamic theory involving ascending geologic brine forced upward into the base of the sabkha by a regional hydraulic gradient in the underlying formations. Ra-226 could uniquely distinguish between these sources under certain circumstances, as it is typically present at elevated activity of hundreds to thousands of Bq/m3 (Becquerels per cubic meter) in subsurface formation brines; at exceedingly low activities in open ocean and coastal water; and not significantly supplied to water from recently formed marine sedimentary framework material. The coastal marine sabkha of the Emirate of Abu Dhabi was used to test this hypothesis. The distribution of Ra-226 in 70 samples of sabkha brine (mean: 700 Bq/m3), 7 samples of underlying deeper formation brine (mean: 3416 Bq/m3), the estimated value of seawater (< 16 Bq/m3) and an estimate of supply from sabkha sedimentary framework grains (<~6 Bq/m3) provide the first direct evidence that ascending geologic brine contributes significantly to the solutes of this sabkha system.

  7. Microbial metabolism in ice and brine at -5°C.

    Science.gov (United States)

    Bakermans, Corien; Skidmore, Mark L

    2011-08-01

    Metabolic activity, but not growth, has been observed in ice at temperatures from -5°C to -32°C. To improve understanding of metabolism in ice, we simultaneously examined various aspects of metabolism ((14) C-acetate utilization, macromolecule syntheses and viability via reduction of CTC) of the glacial isolates Sporosarcina sp. B5 and Chryseobacterium sp. V3519-10 during incubation in nutrient-rich ice and brine at -5°C for 50 days. Measured rates of acetate utilization and macromolecule syntheses were high in the first 20 days suggesting adjustment to the lower temperatures and higher salt concentrations of both the liquid vein network in the ice and the brine. Following this adjustment, reproductive growth of both organisms was evident in brine, and suggested for Sporosarcina sp. B5 in ice by increases in cell numbers and biomass. Chryseobacterium sp. V3519-10 cells incubated in ice remained active. These data indicate that neither low temperature nor high salt concentrations prohibit growth in ice, but some other aspect of living within ice slows growth to within the detection limits of current methodologies. These results imply that microbial growth is plausible in natural ice systems with comparable temperatures and sufficient nutrients, such as debris-rich basal ices of glaciers and ice masses. © 2011 Society for Applied Microbiology and Blackwell Publishing Ltd.

  8. Accessible reactive surface area and abiotic redox reactivity of iron oxyhydroxides in acidic brines

    Science.gov (United States)

    Strehlau, Jennifer H.; Toner, Brandy M.; Arnold, William A.; Penn, R. Lee

    2017-01-01

    The reactivity of iron oxyhydroxide nanoparticles in low pH and high ionic strength solutions was quantified to assess abiotic contributions to oxidation-reduction chemistry in acidic brine environments, such as mine groundwater seepage, lakes in Western Australia, and acid mine drainage settings, which are of global interest for their environmental impacts and unique geomicrobiology. Factors expected to influence accessible and reactive surface area, including Fe(II) adsorption and aggregate size, were measured as a function of pH and CaCl2 concentration and related to the kinetics of redox reactions in aqueous suspensions of synthetic goethite (α-FeOOH), akaganeite (β-FeOOH), and ferrihydrite (Fe10O14(OH)2) nanoparticles. Aqueous conditions and iron oxyhydroxides were chosen based on characterization of natural iron-rich mine microbial mats located in Soudan Underground Mine State Park, Minnesota, USA. Quinone species were used as redox sensors because they are well-defined probes and are present in natural organic matter. Fe(II) adsorption to the iron oxyhydroxide mineral surfaces from aqueous solution was measurable only at pH values above 4 and either decreased or was not affected by CaCl2 concentration. Concentrations at or above 0.020 M CaCl2 in acetate buffer (pH 4.5) induced particle aggregation. Assessment of Fe(II) adsorption and particle aggregation in acidic brine suggested that accessible reactive surface area may be limited in acidic brines. This was supported by observations of decreasing benzoquinone reduction rate by adsorbed Fe(II) at high CaCl2 concentration. In contrast, the hydroquinone oxidation rate increased at high CaCl2 concentrations, which may be due to suppressed adsorption of Fe(II) generated by the reaction. Results suggest that iron geochemical cycling in acidic brine environments will be substantially different than for iron oxyhydroxides in low-saline waters with circumneutral pH. These findings have implications for acidic

  9. Mineralogical changes of a well cement in various H2S-CO2(-brine) fluids at high pressure and temperature.

    Science.gov (United States)

    Jacquemet, Nicolas; Pironon, Jacques; Saint-Marc, Jérémie

    2008-01-01

    The reactivity of a crushed well cement in contact with (1) a brine with dissolved H2S-CO2; (2) a dry H2S-CO2 supercritical phase; (3) a two-phase fluid associating a brine with dissolved H2S-CO2 and a H2S-CO2 supercritical phase was investigated in batch experiments at 500 bar and 120, 200 degrees C. All of the experiments showed that following 15-60 days cement carbonation occurred. The H2S reactivity with cement is limited since it only transformed the ferrites (minor phases) by sulfidation. It appeared that the primary parameter controlling the degree of carbonation (i.e., the rate of calcium carbonates precipitation and CSH (Calcium Silicate Hydrates) decalcification) is the physical state of the fluid phase contacting the minerals. The carbonation degree is complete when the minerals contact at least the dry H2S-CO2 supercritical phase and partial when they contactthe brine with dissolved H2S-CO2. Aragonite (calcium carbonate polymorph) precipitated specifically within the dry H2S-CO2 supercritical phase. CSH cristallinity is improved by partial carbonation while CSH are amorphized by complete carbonation. However, the features evidenced in this study cannot be directly related to effective features of cement as a monolith. Further studies involving cement as a monolith are necessary to ascertain textural, petrophysical, and mechanical evolution of cement.

  10. Chemistry and geothermometry of brine produced from the Salton Sea Scientific drill hole, Imperial Valley, California

    Science.gov (United States)

    Thompson, J.M.; Fournier, R.O.

    1988-01-01

    The December 29-30, 1985, flow test of the State 2-14 well, also known as the Salton Sea Scientific drill hole, produced fluid from a depth of 1865-1877 m at a reservoir temperature of 305????5??C. Samples were collected at five different flashing pressures. The brines are Na-Ca-K-Cl-type waters with very high metal and low SO4 and HCO3 contents. Compositions of the flashed brines were normalized relative to the 25??C densities of the solutions, and an ionic charge balance was achieved by adjusting the Na concentration. Calculated Na/K geothermometer temperatures, using equations suggested by different investigators, range from 326?? to 364??C. The Mg/K2 method gives a temperature of about 350??C, Mg/Li2 about 282??, and Na/Li 395??-418??C. -from Authors

  11. Geochemistry of hydropressured brines in South Louisiana: potential for reaction with injected geopressured waste waters

    Energy Technology Data Exchange (ETDEWEB)

    Hanor, J.S.; Bebout, D.G.; Bachman, A.L. (eds.)

    1981-01-01

    Hydropressured, saline-water sands are being considered as possible sites for the disposal of geopressured-geothermal waste waters in South Louisiana. Probable injection horizons would most likely contain native brines of 120 to 140 g/l TDS. These brines show wide ranges in concentration of dissolved Ca, Sr, Ba, Fe, SO/sub 4/, and HCO/sub 3/, even within a restricted range of salinities. The probability is high that mineral precipitation will occur if untreated geopressured wastes are mixed with these waters. Clay migration and additional plugging of the injection well is possible if the injected wastes are significantly less saline than the native fluids. Costs of site-specific geochemical evaluation and chemical pre-treatment are thus factors which must be considered in the economic evaluation of deep well disposal of geopressured wastes in South Louisiana.

  12. Effect of iron cation on geochemical trapping of CO2 in brine

    Science.gov (United States)

    Liu, Qi; Maroto-Valer, Mercedes

    2014-05-01

    Carbon dioxide sequestration using brines has emerged as a promising technology to mitigate the adverse impacts of climate change due to its large storage capacity and favorable chemistries. However, the permanent storage (mineral trapping) of CO2 in brines takes significantly long periods of time as the formation and precipitation of carbonates is very slow .[1]. The main parameters reported to effect on mineral trapping of CO2 sequestration in brines are brine composition, brine pH, system temperature and pressure.[2, 3]. It is suggested that the precipitation of mineral carbonates is mostly dependent on brine pH. Previous studies by the authors concluded that iron in natural brines causes pH instability, but it was not ascertained whether ferric iron or ferrous iron caused pH instability .[4]. Accordingly, the aim of this project is to study synthetic brines mimicking the major ions found in natural brines and including different concentrations of ferric and ferrous iron. Three brines were prepared, as follows: Brine 1 was prepared with ferric Fe3+ iron, Brine 2 prepared with ferrous Fe2+ iron and Brine 3 prepared with no iron. A series of pH stability studies and carbonation reactions were conducted using the above three brines. It is concluded that the ferrous iron causes pH instability, while ferric iron might promote carbonate precipitation. .1. Garcia, S., et al., Sequestration of non-pure carbon dioxide streams in iron oxyhydroxide-containing saline repositories. International Journal of Greenhouse Gas Control, 2012. 7: p. 89-97. 2. Liu, Q. and M.M. Maroto-Valer, Investigation of the pH effect of a typical host rock and buffer solution on CO 2 sequestration in synthetic brines. Fuel Processing Technology, 2010. 91(10): p. 1321-1329. 3. Liu, Q. and M.M. MarotoValer, Parameters affecting mineral trapping of CO2 sequestration in brines. Greenhouse Gases: Science and Technology, 2011. 1(3): p. 211-222. 4. Druckenmiller, M.L. and M.M. Maroto-Valer, Carbon

  13. Physical chemistry of highly concentrated emulsions.

    Science.gov (United States)

    Foudazi, Reza; Qavi, Sahar; Masalova, Irina; Malkin, Alexander Ya

    2015-06-01

    This review explores the physics underlying the rheology of highly concentrated emulsions (HCEs) to determine the relationship between elasticity and HCE stability, and to consider whether it is possible to describe all physicochemical properties of HCEs on the basis of a unique physical approach. We define HCEs as emulsions with a volume fraction above the maximum closest packing fraction of monodisperse spheres, φm=0.74, even if droplets are not of polyhedron shape. The solid-like rheological behavior of HCEs is characterized by yield stress and elasticity, properties which depend on droplet polydispersity and which are affected by caging at volume fractions about the jamming concentration, φj. A bimodal size distribution in HCEs diminishes caging and facilitates droplet movement, resulting in HCEs with negligible yield stress and no plateau in storage modulus. Thermodynamic forces automatically move HCEs toward the lowest free energy state, but since interdroplet forces create local minimums - points beyond which free energy temporarily increases before it reaches the global minimum of the system - the free energy of HCEs will settle at a local minimum unless additional energy is added. Several attempts have been undertaken to predict the elasticity of HCEs. In many cases, the elastic modulus of HCEs is higher than the one predicted from classical models, which only take into account spatial repulsion (or simply interfacial energy). Improved models based on free energy calculation should be developed to consider the disjoining pressure and interfacial rheology in addition to spatial repulsion. The disjoining pressure and interfacial viscoelasticity, which result in the deviation of elasticity from the classical model, can be regarded as parameters for quantifying the stability of HCEs. Copyright © 2015 Elsevier B.V. All rights reserved.

  14. Corrosion mechanism of 13Cr stainless steel in completion fluid of high temperature and high concentration bromine salt

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Yan [Corrosion and Protection Center, Key Laboratory for Environmental Fracture (MOE), Institute for Advanced Materials and Technology, University of Science and Technology Beijing, Beijing 100083 (China); Xu, Lining, E-mail: xulining@ustb.edu.cn [Corrosion and Protection Center, Key Laboratory for Environmental Fracture (MOE), Institute for Advanced Materials and Technology, University of Science and Technology Beijing, Beijing 100083 (China); Lu, Minxu [Corrosion and Protection Center, Key Laboratory for Environmental Fracture (MOE), Institute for Advanced Materials and Technology, University of Science and Technology Beijing, Beijing 100083 (China); Meng, Yao [Beijing Institute of Aeronautical Materials, Beijing 100095 (China); Zhu, Jinyang; Zhang, Lei [Corrosion and Protection Center, Key Laboratory for Environmental Fracture (MOE), Institute for Advanced Materials and Technology, University of Science and Technology Beijing, Beijing 100083 (China)

    2014-09-30

    Highlights: • The corrosion behavior of 13Cr steel exposed to bromine salt completion fluid containing high concentration bromine ions was investigated. • There are passive circles around pits on the 13Cr steel surface after 7 d of exposure. • Macroscopic galvanic corrosion formed between the passive halo and the pit. • The mechanism of pitting corrosion on 13Cr stainless steel exposed to heavy bromine brine was established. - Abstract: A series of corrosion tests of 13Cr stainless steel were conducted in a simulated completion fluid environment of high temperature and high concentration bromine salt. Corrosion behavior of specimens and the component of corrosion products were investigated by means of scanning electron microscope (SEM), confocal laser scanning microscopy (CLSM) and X-ray photoelectron spectroscopy (XPS). The results indicate that 13Cr steel suffers from severe local corrosion and there is always a passive halo around every pit. The formation mechanism of the passive halo is established. OH{sup −} ligand generates and adsorbs in a certain scale because of abundant OH{sup −} on the surface around the pits. Passive film forms around each pit, which leads to the occurrence of passivation in a certain region. Finally, the dissimilarities in properties and morphologies of regions, namely the pit and its corresponding passive halo, can result in different corrosion sensitivities and may promote the formation of macroscopic galvanic pairs.

  15. Potentials of converting microalgae into brine shrimp Artemia

    OpenAIRE

    Sorgeloos, P.

    1985-01-01

    High densities of brine shrimp Artemia can be cultured in flow-through systems using the effluent of microalgae cultures as a combined source of culture medium and food. It has been proven at the "St. Croix Artificial Upwelling Mariculture Project" that in comparison with the fast growing clam Tapes japonica, brine shrimp assure a much more efficient conversion of plant into animal biomass. It appears from the given examples that microalgae conversion into brine shrimp Artemia offers efficien...

  16. High resolution spectrophotometry for identification of chlorine dioxide in concentrated chlorine solutions.

    Science.gov (United States)

    Gauw, R D; Emmert, G L; Bubnis, B; Gordon, G

    1999-12-06

    Electrolyzed salt brine generators hold great promise for water disinfection in small communities and remote locations. Electrolysis cell liquors have been reported to contain chlorine, chlorine dioxide and ozone. High resolution spectrophotometry was used to observe the presence (or absence) of a unique spectral absorbance pattern present in solutions containing 1-2 mg/l chlorine dioxide.

  17. CO2-brine-mineral Reactions in Geological Carbon Storage: Results from an EOR Experiment

    Science.gov (United States)

    Chapman, H.; Wigley, M.; Bickle, M.; Kampman, N.; Dubacq, B.; Galy, A.; Ballentine, C.; Zhou, Z.

    2012-04-01

    Dissolution of CO2 in brines and reactions of the acid brines ultimately dissolving silicate minerals and precipitating carbonate minerals are the prime long-term mechanisms for stabilising the light supercritical CO2 in geological carbon storage. However the rates of dissolution are very uncertain as they are likely to depend on the heterogeneity of the flow of CO2, the possibility of convective instability of the denser CO2-saturated brines and on fluid-mineral reactions which buffer brine acidity. We report the results of sampling brines and gases during a phase of CO2 injection for enhanced oil recovery in a small oil field. Brines and gases were sampled at production wells daily for 3 months after initiation of CO2 injection and again for two weeks after 5 months. Noble gas isotopic spikes were detected at producing wells within days of initial CO2 injection but signals continued for weeks, and at some producers for the duration of the sampling period, attesting to the complexity of gas-species pathways. Interpretations are complicated by the previous history of the oil field and re-injection of produced water prior to injection of CO2. However water sampled from some producing wells during the phase of CO2 injection showed monotonic increases in alkalinity and in concentrations of major cations to levels in excess of those in the injected water. The marked increase in Na, and smaller increases in Ca, Mg, Si, K and Sr are interpreted primarily to result from silicate dissolution as the lack of increase in S and Cl concentrations preclude additions of more saline waters. Early calcite dissolution was followed by re-precipitation. 87Sr/86Sr ratios in the waters apparently exceed the 87Sr/86Sr ratios of acetic and hydrochloric acid leaches of carbonate fractions of the reservoir rocks and the silicate residues from the leaching. This may indicate incongruent dissolution of Sr or larger scale isotopic heterogeneity of the reservoir. This is being investigated

  18. Chemical and isotopic characteristics of brines from three oil- and gas-producing sandstones in eastern Ohio, with applications to the geochemical tracing of brine sources

    Science.gov (United States)

    Breen, K.J.; Angelo, Clifford G.; Masters, Robert W.; Sedam, Alan C.

    1985-01-01

    Chemical and isotopic characteristics of selected inorganic constituents are reported for brines from the Berea Sandstone of Mississippian age, the Clinton sandstone, Albion Sandstone of Silurian age, and the Rose Run formation of Cambrian and Ordovician age in 24 counties in eastern Ohio. Ionic concentrations of dissolved constituents in brines from these formations generally fall in the following ranges (in millimoles per kilogram of brine): Na, Cl > 1,000; 100 Al, I, HCO3, SiO2 Mg, Na, Cl, K, SO4 and Br, and mean values of density and dissolved solids are significantly different at the 95-percent confidence level in each formation. Only potassium has a unique concentration range in each formation. Selected concentration ratios are identified as potential indicators for geochemical tracing of brines having some history of dilution. The k:Na ratios work best for identifying the source formation of an unidentified brine. Isotopic characteristics of hydrogen and oxygen indicate a meteoric origin for the water matrix of the brines. Sulfur isotopes may have utility for differentiating brines from oxidizing ground water.

  19. Carbon isotopic evidence for microbial control of carbon supply to Orca Basin at the brine-seawater interface

    Directory of Open Access Journals (Sweden)

    S. R. Shah

    2012-12-01

    Full Text Available Orca Basin, an intraslope basin on the Texas–Louisiana continental slope, hosts a hypersaline, anoxic brine in its lowermost 200 m. This brine contains a large reservoir of reduced and aged carbon, and appears to be stable at decadal time scales: concentrations and the isotopic composition of dissolved inorganic (DIC and organic carbon (DOC are similar to previous reports. Both DIC and DOC are more "aged" within the brine pool than in overlying water, and the isotopic contrast between brine carbon and seawater carbon is much greater for DIC than DOC. While the stable carbon isotopic composition of brine DIC points towards a combination of methane and organic carbon re-mineralization as its source, radiocarbon and box model results point to the brine interface as the major source region for DIC with oxidation of methane diffusing upwards from sediments supplying only limited DIC to the brine. This conclusion is consistent with previous studies reporting microbial activity focused at the seawater-brine interface. Isotopic similarities between DIC and DOC suggest a different relationship between these two carbon reservoirs than is typically observed in deep ocean basins. Radiocarbon values implicate the seawater-brine interface region as the likely source region for DOC as well as DIC. Further investigations of the seawater-brine interface are needed to advance our understanding of the specific microbial processes contributing to dissolved carbon storage in the Orca Basin brine.

  20. Energy storage in evaporated brine

    Energy Technology Data Exchange (ETDEWEB)

    MacDonald, R. Ian

    2010-09-15

    We propose storage of electrical energy in brine solutions by using the energy to enhance natural evaporation. Using properties of existing industrial evaporation technologies and estimates of power regeneration from brine by pressure retarded osmosis, efficiency near 100% is calculated. Modelling indicates that systems ranging from 50kW to 50MW output may be practical, with storage capacities of hours to days. The method appears to have potential to be economically competitive with other technologies over a wide range of capacity. It may present a large new application area that could aid the development of salinity-based power generation technology.

  1. High-Temperature, High-Concentration Solar Thermoelectric Generators

    Science.gov (United States)

    Warren, Emily; Baranowski, Lauryn; Olsen, Michele; Ndione, Paul; Netter, Judy; Goodrich, Alan; Gray, Matthew; Parilla, Philip; Ginley, David; Toberer, Eric

    2014-03-01

    Solar thermoelectric generators (STEGs) powered with concentrated solar energy have potential for use as primary energy converters or as topping-cycles for more conventional concentrated solar power (CSP) technologies. Modeling based on current record modules from JPL suggests thermoelectric efficiencies of 18 % could be experimentally expected with a temperature gradient of 1000 - 100°C. Integrating these state-of-the-art TEGs with a concentrating solar receiver requires simultaneous optimization of optical, thermal, and thermoelectric systems. This talk will discuss the modeling, design, and experimental testing of STEG devices under concentrated sunlight. We have developed a model that combines thermal circuit modeling with optical ray tracing to design selective absorber coatings and cavities to minimize radiation losses from the system. We have fabricated selective absorber coatings and demonstrated that these selective absorber films can minimize blackbody radiation losses at high temperature and are stable after thermal cycling to 1000°C. On-sun testing of STEG devices and thermal simulators is ongoing and preliminary results will be discussed.

  2. Production of high concentrations of yeast

    Energy Technology Data Exchange (ETDEWEB)

    1981-11-10

    A microbe is aerobically cultured using O/sub 2/ or a gas rich in O/sub 2/. The grown cells are washed, concentrated and a portion of the cells used as a seed culture. Thus, Saccharomyces cerevisiae (bakers' yeast) was cultured in a jar fermentor by flow down system maintaining the dissolved O/sub 2/ at 2-5 mg/L; volume of the initial medium containing 30% glucose was 350 mL and the initial washed cell concentration was 50 g dry cells/L. After 12 hours of cultivation, the volume of the medium increased to 750 mL and the cell concentration rose to 102 g dry cells/L; the yield was 49% with respect to glucose. The cells were washed and the cultivation was repeated by use of the washed cells; cell concentration reached 105 g dry cells/L.

  3. 深井岩盐卤水地热能综合利用研究%Study on Comprehensive Utilization of Deep Geothermal Brine

    Institute of Scientific and Technical Information of China (English)

    卜明

    2016-01-01

    本文对卤水携带的地热能进行了分析研究,在岩盐卤水井下处理的基础上,根据亨利定律P=EX,提出了携带地热卤水经"闪蒸"浓缩降温后,再与制盐蒸发冷凝水进行换热,使冷凝水中的热量转移至浓缩卤水中,提高温度后再进入制盐系统制盐. 这为深井岩盐地热与制盐冷凝水潜热综合利用提供了一种全新的思路与方法.%This paper analyzes and researches the geo thermal energy which is carrying by brine, and on the basis of the underground rock salt brine treatment, according to the Henry's law (P = EX), put forward carrying geothermal brine after "flash"condensed cooling and heat exchange with high evaporation condensation water, can make the condensed water in the heat transferred to the concentrated brine, raise the temperature and then put it into the salt making system. It provides a new thinking and method for the comprehensive utilization of deep geothermal brine and the latent heat of salt making condensation water.

  4. EOS7Cm: An improved TOUGH2 module for simulating non-isothermal multiphase and multicomponent flow in CO2-H2S-CH4-brine systems with high pressure, temperature and salinity

    Science.gov (United States)

    Lei, Hongwu; Li, Jun; Li, Xiaochun; Jiang, Zhenjiao

    2016-09-01

    Understanding the non-isothermal multiphase and multicomponent flow in a CO2-H2S-CH4-brine system is of critical importance in projects such as CO2 storage in deep saline aquifers, natural gas extraction using CO2 as the displacement fluid, and heat extraction from hot dry rocks using CO2 as the working fluid. Numerical simulation is a necessary tool to evaluate the chemical evolution in these systems. However, an accurate thermodynamic model for CO2-H2S-CH4-brine systems appropriate for high pressure, temperature, and salinity is still lacking. This study establishes the mutual solubility model for CO2-H2S-CH4-brine systems based on the fugacity-activity method for phase equilibrium. The model can predict mutual solubilities for pressure up to 1000 bar for CO2 and CH4, and 200 bar for H2S, for temperature up to 200 °C, and for salinity up to 6 mol/kg water. We incorporated the new model into TOUGH2/EOS7C, forming a new improved module we call EOS7Cm. Compared to the original EOS7C, EOS7Cm considers the effects of H2S and covers a larger range of temperature and salinity. EOS7Cm is employed in five examples, including CO2 injection with and without impurities (CH4 and/or H2S) into deep aquifers, CH4 extraction from aquifers by CO2 injection, and heat extraction from hot dry rock. The results are compared to those from TOUGH2/ECO2N, EOS7C and CMG, agreement among which serves to verify EOS7Cm.

  5. Precipitation of halite from supersaline brine from Tønder formation

    DEFF Research Database (Denmark)

    Arturi, Kasia; Søgaard, Erik Gydesen

    2014-01-01

    This project deals various treatments for geothermal brine, which is a highly salty solution containing more that 50 TDS (Total Dissolved Solids). This project focuses on the brine from Tønder formation (T=73°C), which has an extraordinarily high salt content NaCl ([C] = 300-310 g/l). According...

  6. Horizontally staggered lightguide solar concentrator with lateral displacement tracking for high concentration applications.

    Science.gov (United States)

    Ma, Hongcai; Wu, Lin

    2015-07-10

    We present the design of a horizontally staggered lightguide solar concentrator with lateral displacement tracking for high concentration applications. This solar concentrator consists of an array of telecentric primary concentrators, a horizontally staggered lightguide layer, and a vertically tapered lightguide layer. The primary concentrator is realized by two plano-aspheric lenses with lateral movement and maintains a high F-number over an angle range of ±23.5°. The results of the simulations show that the solar concentrator achieves a high concentration ratio of 500× with ±0.5° of acceptance angle by a single-axis tracker and dual lateral translation stages.

  7. 7 CFR 58.320 - Brine tanks.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Brine tanks. 58.320 Section 58.320 Agriculture....320 Brine tanks. Brine tanks used for the treating of parchment liners shall be constructed of... liners. The tank should also be provided with a satisfactory drainage outlet....

  8. Brine Sampling and Evaluation Program, 1991 report

    Energy Technology Data Exchange (ETDEWEB)

    Deal, D.E.; Abitz, R.J.; Myers, J.; Martin, M.L.; Milligan, D.J.; Sobocinski, R.W.; Lipponer, P.P.J. [International Technology Corp., Albuquerque, NM (United States); Belski, D.S. [Westinghouse Electric Corp., Carlsbad, NM (United States). Waste Isolation Div.

    1993-09-01

    The data presented in this report are the result of Brine Sampling and Evaluation Program (BSEP) activities at the Waste Isolation Pilot Plan (WIPP) during 1991. These BSEP activities document and investigate the origins, hydraulic characteristics, extent, and composition of brine occurrences in the Permian Salado Formation and seepage of that brine into the excavations at the WIPP. When excavations began at the WIPP in 1982, small brine seepages (weeps) were observed on the walls. Brine studies began as part of the Site Validation Program and were formalized as a program in its own right in 1985. During nine years of observations (1982--1991), evidence has mounted that the amount of brine seeping into the WIPP excavations is limited, local, and only a small fraction of that required to produce hydrogen gas by corroding the metal in the waste drums and waste inventory. The data through 1990 is discussed in detail and summarized by Deal and others (1991). The data presented in this report describes progress made during the calendar year 1991 and focuses on four major areas: (1) quantification of the amount of brine seeping across vertical surfaces in the WIPP excavations (brine ``weeps); (2) monitoring of brine inflow, e.g., measuring brines recovered from holes drilled downward from the underground drifts (downholes), upward from the underground drifts (upholes), and from subhorizontal holes; (3) further characterization of brine geochemistry; and (4) preliminary quantification of the amount of brine that might be released by squeezing the underconsolidated clays present in the Salado Formation.

  9. Actinide (III) solubility in WIPP Brine: data summary and recommendations

    Energy Technology Data Exchange (ETDEWEB)

    Borkowski, Marian; Lucchini, Jean-Francois; Richmann, Michael K.; Reed, Donald T.

    2009-09-01

    The solubility of actinides in the +3 oxidation state is an important input into the Waste Isolation Pilot Plant (WIPP) performance assessment (PA) models that calculate potential actinide release from the WIPP repository. In this context, the solubility of neodymium(III) was determined as a function of pH, carbonate concentration, and WIPP brine composition. Additionally, we conducted a literature review on the solubility of +3 actinides under WIPP-related conditions. Neodymium(III) was used as a redox-invariant analog for the +3 oxidation state of americium and plutonium, which is the oxidation state that accounts for over 90% of the potential release from the WIPP through the dissolved brine release (DBR) mechanism, based on current WIPP performance assessment assumptions. These solubility data extend past studies to brine compositions that are more WIPP-relevant and cover a broader range of experimental conditions than past studies.

  10. Impact of the brine from a desalination plant on a shallow seagrass ( Posidonia oceanica) meadow

    Science.gov (United States)

    Gacia, Esperança; Invers, Olga; Manzanera, Marta; Ballesteros, Enric; Romero, Javier

    2007-05-01

    Although seawater desalination has increased significantly over recent decades, little attention has been paid to the impact of the main by-product (hypersaline water: brine) on ecosystems. In the Mediterranean, potentially the most affected ecosystems are meadows of the endemic seagrass Posidonia oceanica. We studied the effect of brine on a shallow P. oceanica meadow exposed to reverse osmosis brine discharge for more than 6 years. P. oceanica proved to be very sensitive to both eutrophication and high salinities derived from the brine discharge. Affected plants showed high epiphyte load and nitrogen content in the leaves, high frequencies of necrosis marks, low total non-structural carbohydrates and low glutamine synthetase activity, compared to control plants. However, there was no indication of extensive decline of the affected meadow. This is probably due to its very shallow situation, which results in high incident radiation as well as fast dilution and dispersion of the brine plume.

  11. Hydrogeochemical characterization and groundwater quality assessment in intruded coastal brine aquifers (Laizhou Bay, China).

    Science.gov (United States)

    Zhang, Xiaoying; Miao, Jinjie; Hu, Bill X; Liu, Hongwei; Zhang, Hanxiong; Ma, Zhen

    2017-07-20

    The aquifer in the coastal area of the Laizhou Bay is affected by salinization processes related to intense groundwater exploitation for brine resource and for agriculture irrigation during the last three decades. As a result, the dynamic balances among freshwater, brine, and seawater have been disturbed and the quality of groundwater has deteriorated. To fully understand the groundwater chemical distribution and evolution in the regional aquifers, hydrogeochemical and isotopic studies have been conducted based on the water samples from 102 observation wells. Groundwater levels and salinities in four monitoring wells are as well measured to inspect the general groundwater flow and chemical patterns and seasonal variations. Chemical components such as Na(+), K(+), Ca(2+), Mg(2+), Sr(2+), Cl(-), SO4(2-), HCO3(-), NO3(-), F(-), and TDS during the same period are analyzed to explore geochemical evolution, water-rock interactions, sources of salt, nitrate, and fluoride pollution in fresh, brackish, saline, and brine waters. The decreased water levels without typical seasonal variation in the southeast of the study area confirm an over-exploitation of groundwater. The hydrogeochemical characteristics indicate fresh-saline-brine-saline transition pattern from inland to coast where evaporation is a vital factor to control the chemical evolution. The cation exchange processes are occurred at fresh-saline interfaces of mixtures along the hydraulic gradient. Meanwhile, isotopic data indicate that the brine in aquifers was either originated from older meteoric water with mineral dissolution and evaporation or repeatedly evaporation of retained seawater with fresher water recharge and mixing in geological time. Groundwater suitability for drinking is further evaluated according to water quality standard of China. Results reveal high risks of nitrate and fluoride contamination. The elevated nitrate concentration of 560 mg/L, which as high as 28 times of the standard content in

  12. Brine Transport Experiments in Granular Salt

    Energy Technology Data Exchange (ETDEWEB)

    Jordan, Amy B. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Boukhalfa, Hakim [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Caporuscio, Florie Andre [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Stauffer, Philip H. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-06-06

    To gain confidence in the predictive capability of numerical models, experimental validation must be performed to ensure that parameters and processes are correctly simulated. The laboratory investigations presented herein aim to address knowledge gaps for heat-generating nuclear waste (HGNW) disposal in bedded salt that remain after examination of prior field and laboratory test data. Primarily, we are interested in better constraining the thermal, hydrological, and physicochemical behavior of brine, water vapor, and salt when moist salt is heated. The target of this work is to use run-of-mine (RoM) salt; however during FY2015 progress was made using high-purity, granular sodium chloride.

  13. Brine Sampling and Evaluation Program, 1990 report

    Energy Technology Data Exchange (ETDEWEB)

    Deal, D.E.; Abitz, R.J.; Myers, J.; Case, J.B.; Martin, M.L.; Roggenthen, W.M. [International Technology Corp., Albuquerque, NM (United States); Belski, D.S. [Westinghouse Electric Corp., Carlsbad, NM (United States). Waste Isolation Div.

    1991-08-01

    The data presented in this report are the result of Brine Sampling and Evaluation Program (BSEP) activities at the Waste Isolation Pilot Plant (WIPP) during 1990. When excavations began in 1982, small brine seepages (weeps) were observed on the walls. These brine occurrences were initially described as part of the Site Validation Program. Brine studies were formalized in 1985. The BSEP activities document and investigate the origins, hydraulic characteristics, extent, and composition of brine occurrences in the Permian Salado Formation and seepage of that brine into the excavations at the WIPP. The brine chemistry is important because it assists in understanding the origin of the brine and because it may affect possible chemical reactions in the buried waste after sealing the repository. The volume of brine and the hydrologic system that drives the brine seepage also need to be understood to assess the long-term performance of the repository. After more than eight years of observations (1982--1990), no credible evidence exists to indicate that enough naturally occurring brine will seep into the WIPP excavations to be of practical concern. The detailed observations and analyses summarized herein and in previous BSEP reports confirm the evidence apparent during casual visits to the underground workings -- that the excavations are remarkably dry.

  14. Isolation and characterization of a heavy metal-resistant, thermophilic esterase from a Red Sea Brine Pool

    KAUST Repository

    Mohamed, Yasmine M.

    2013-11-28

    The Red Sea Atlantis II brine pool is an extreme environment that displays multiple harsh conditions such as high temperature, high salinity and high concentrations of multiple, toxic heavy metals. The survival of microbes in such an environment by utilizing resistant enzymes makes them an excellent source of extremophilic enzymes. We constructed a fosmid metagenomic library using DNA isolated from the deepest and most secluded layer of this pool. We report the isolation and biochemical characterization of an unusual esterase: EstATII. EstATII is thermophilic (optimum temperature, 65 C), halotolerant (maintains its activity in up to 4.5â€...M NaCl) and maintains at least 60% of its activity in the presence of a wide spectrum of heavy metals. The combination of biochemical characteristics of the Red Sea Atlantis II brine pool esterase, i.e., halotolerance, thermophilicity and resistance to heavy metals, makes it a potentially useful biocatalyst.

  15. Stability of polyvinyl alcohol-coated biochar nanoparticles in brine

    Science.gov (United States)

    Griffith, Christopher; Daigle, Hugh

    2017-01-01

    This paper reports on the dispersion stability of 150 nm polyvinyl alcohol coated biochar nanoparticles in brine water. Biochar is a renewable, carbon based material that is of significant interest for enhanced oil recovery operations primarily due to its wide ranging surface properties, low cost of synthesis, and low environmental toxicity. Nanoparticles used as stabilizing agents for foams (and emulsions) or in nanofluids have emerged as potential alternatives to surfactants for subsurface applications due to their improved stability at reservoir conditions. If, however, the particles are not properly designed, they are susceptible to aggregation because of the high salinity brines typical of oil and gas reservoirs. Attachment of polymers to the nanoparticle surface, through covalent bonds, provides steric stabilization, and is a necessary step. Our results show that as the graft density of polyvinyl alcohol increases, so too does the stability of nanoparticles in brine solutions. A maximum of 34 wt% of 50,000 Da polyvinyl alcohol was grafted to the particle surface, and the size of the particles was reduced from 3500 nm (no coating) to 350 nm in brine. After 24 h, the particles had a size of 500 nm, and after 48 h completely aggregated. 100,000 Da PVA coated at 24 wt% on the biochar particles were stable in brine for over 1 month with no change in mean particle size of 330 nm.

  16. Geochemistry of Salado Formation brines recovered from the Waste Isolation Pilot Plant (WIPP) repository

    Energy Technology Data Exchange (ETDEWEB)

    Abitz, R.; Myers, J.; Drez, P.; Deal, D.

    1990-01-01

    Intergranular brines recovered from the repository horizon of the Waste Isolation Pilot Plant (WIPP) have major- and trace-element compositions that reflect seawater evaporation and diagenetic processes. Brines obtained from repository drill holes are heterogenous with respect to composition, but their compositional fields are distinct from those obtained from fluid inclusions in WIPP halite. The heterogeneity of brine compositions within the drill-hole population indicates a lack of mixing and fluid homogenization within the salt at the repository level. Compositional differences between intergranular (drill hole) and intragranular (fluid inclusions) brines is attributed to isolation of the latter from diagenetic fluids that were produced from dehydration reactions involving gypsum and clay minerals. Modeling of brine-rock equilibria indicates that equilibration with evaporite minerals controls the concentrations of major elements in the brine. Drill-hole brines are in equilibrium with the observed repository minerals halite, anhydrite, magnesite, polyhalite and quartz. The equilibrium model supports the derivation of drill-hole brines from near-field fluid, rather than large-scale vertical migration of fluids from the overlying Rustler or underlying Castile Formations. 13 refs., 6 figs., 6 tabs.

  17. Survival of Escherichia coli O157:H7 during manufacture and storage of white brined cheese.

    Science.gov (United States)

    Osaili, Tareq M; Al-Nabulsi, Anas A; Olaimat, Amin N; Shaker, Reyad R; Taha, Mohammad; Holley, Richard A

    2014-09-01

    Escherichia coli O157:H7 is a major foodborne pathogen that causes severe disease in humans. Survival of E. coli O157:H7 during processing and storage of white brined cheese was investigated. Cheeses were prepared using pasteurized milk inoculated with a 4 strain E. coli O157:H7 cocktail (7 log(10) CFU/g) with or without yogurt starter culture (Lactobacillus delbrueckii ssp. bulgaricus and Streptococcus salivarius ssp. thermophilus) and stored in 10% or 15% NaCl brine at 10 and 21 ºC for 28 d. NaCl concentration, water activity (a(w)), pH, and numbers of E. coli O157:H7 and lactic acid bacteria (LAB) were determined in cheese and brine. E. coli O157:H7 was able to survive in cheese stored in both brines at 10 and 21 ºC regardless of the presence of starter LAB, although the latter significantly enhanced E. coli O157:H7 reduction in cheese or its brine at 10 ºC. E. coli O157:H7 numbers were reduced by 2.6 and 3.4 log(10) CFU/g in cheese stored in 10% and 15% NaCl brine, respectively, in the presence of starter LAB and by 1.4 and 2.3 log(10) CFU/g, respectively, in the absence of starter LAB at 10 ºC. The pathogen survived, but at lower numbers in the brines. The salt concentration of cheese stored in 10% brine remained about 5% during ripening, but in 15% brine, the NaCl level increased 1.6% to 8.1% (w/w) by 28 d. Values of pH and a(w) slightly decreased 1 d after exposure to brine and reached 5.5 to 6.6 and 0.88 to 0.94, respectively, in all treatments.

  18. Selective Recovery of Metals from Geothermal Brines

    Energy Technology Data Exchange (ETDEWEB)

    Ventura, Susanna [SRI International, Menlo Park, CA (United States); Bhamidi, Srinivas [SRI International, Menlo Park, CA (United States); Hornbostel, Marc [SRI International, Menlo Park, CA (United States); Nagar, Anoop [SRI International, Menlo Park, CA (United States); Perea, Elisabeth [SRI International, Menlo Park, CA (United States)

    2016-12-16

    The objective of this project was to determine the feasibility of developing a new generation of highly selective low-cost ion-exchange resins based on metal-ion imprinted polymers for the separation of metals from geothermal fluids. Expansion of geothermal energy production over the entire U.S. will involve exploitation of low-to-medium temperature thermal waters. Creating value streams from the recovery of critical and near-critical metals from these thermal waters will encourage geothermal expansion. Selective extraction of metals from geothermal fluids is needed to design a cost-effective process for the recovery of lithium and manganese-two near-critical metals with well-known application in the growing lithium battery industry. We have prepared new lithium- and manganese-imprinted polymers in the form of beads by crosslinking polymerization of a metal polymerizable chelate, where the metal acts as a template. Upon leaching out the metal template, the crosslinked polymer is expected to leave cavities defined by the ligand functional group with enhanced selectivity for binding the template metal. We have demonstrated that lithium- and manganese-imprinted polymer beads can be used as selective solid sorbents for the extraction of lithium and manganese from brines. The polymers were tested both in batch extractions and packed bed lab-scale columns at temperatures of 45-100°C. Lithium-imprinted polymers were found to have Li+ adsorption capacity as high as 2.8 mg Li+/g polymer at 45°C. Manganese-imprinted polymers were found to have a Mn2+ adsorption capacity of more than 23 mg Mn2+/g polymer at 75°C. The Li+ extraction efficiency of the Li-imprinted polymer was found to be more that 95% when a brine containing 390 ppm Li+, 410 ppm Na+, and 390 ppm K+ was passed through a packed bed of the polymer in a lab-scale column at 45°C. In brines containing 360 ppm Li

  19. Microbially mediated barite dissolution in anoxic brines

    Science.gov (United States)

    Ouyang, Bingjie; Akob, Denise M.; Dunlap, Darren S.; Renock, Devon

    2017-01-01

    Fluids injected into shale formations during hydraulic fracturing of black shale return with extraordinarily high total-dissolved-solids (TDS) and high concentrations of barium (Ba) and radium (Ra). Barite, BaSO4, has been implicated as a possible source of Ba as well as a problematic mineral scale that forms on internal well surfaces, often in close association with radiobarite, (Ba,Ra)SO4. The dissolution of barite by abiotic processes is well quantified. However, the identification of microbial communities in flowback and produced water necessitates the need to understand barite dissolution in the presence of bacteria. Therefore, we evaluated the rates and mechanisms of abiotic and microbially-mediated barite dissolution under anoxic and hypersaline conditions in the laboratory. Barite dissolution experiments were conducted with bacterial enrichment cultures established from produced water from Marcellus Shale wells located in northcentral Pennsylvania. These cultures were dominated by anaerobic halophilic bacteria from the genus Halanaerobium. Dissolved Ba was determined by ICP-OES and barite surfaces were investigated by SEM and AFM. Our results reveal that: 1) higher amounts of barium (up to ∼5 × ) are released from barite in the presence of Halanaerobium cultures compared to brine controls after 30 days of reaction, 2) etch pits that develop on the barite (001) surface in the presence of Halanaerobium exhibit a morphology that is distinct from those that form during control experiments without bacteria, 3) etch pits that develop in the presence of Halanaerobium exhibit a morphology that is similar to the morphology of etch pits formed in the presence of strong organic chelators, EDTA and DTPA, and 4) experiments using dialysis membranes to separate barite from bacteria suggest that direct contact between the two is not required in order to promote dissolution. These results suggest that Halanaerobium increase the rate of barite dissolution in anoxic and

  20. Selectivity and Mass Transfer Limitations in Pressure-Retarded Osmosis at High Concentrations and Increased Operating Pressures.

    Science.gov (United States)

    Straub, Anthony P; Osuji, Chinedum O; Cath, Tzahi Y; Elimelech, Menachem

    2015-10-20

    Pressure-retarded osmosis (PRO) is a promising source of renewable energy when hypersaline brines and other high concentration solutions are used. However, membrane performance under conditions suitable for these solutions is poorly understood. In this work, we use a new method to characterize membranes under a variety of pressures and concentrations, including hydraulic pressures up to 48.3 bar and concentrations of up to 3 M NaCl. We find membrane selectivity decreases as the draw solution concentration is increased, with the salt permeability coefficient increasing by a factor of 2 when the draw concentration is changed from 0.6 to 3 M NaCl, even when the applied hydraulic pressure is maintained constant. Additionally, we find that significant pumping energy is required to overcome frictional pressure losses in the spacer-filled feed channel and achieve suitable mass transfer on the feed side of the membrane, especially at high operating pressures. For a meter-long module operating at 41 bar, we estimate feedwater will have to be pumped in at a pressure of at least 3 bar. Both the reduced selectivity and increased pumping energy requirements we observe in PRO will significantly diminish the obtainable net energy, highlighting important new challenges for development of systems utilizing hypersaline draw solutions.

  1. Spectroscopy and detectability of liquid brines on mars

    Science.gov (United States)

    Massé, M.; Beck, P.; Schmitt, B.; Pommerol, A.; McEwen, A.; Chevrier, V.; Brissaud, O.; Séjourné, A.

    2014-03-01

    Recent geomorphological observations as well as chemical and thermodynamic studies demonstrate that liquid water should be stable today on the Martian surface at some times of the day. In Martian conditions, brines would be particularly more stable than pure water because salts can depress the freezing point and lower the evaporation rate of water. Despite this evidence, no clear spectral signature of liquid has been observed so far by the hyperspectral imaging spectrometers OMEGA and CRISM. However, past spectral analysis lacks a good characterization of brines' spectral signatures. This study thus aims to determine how liquid brines can be detected on Mars by spectroscopy. In this way, laboratory experiments were performed for reproducing hydration and dehydration cycles of various brines while measuring their spectral signatures. The resulting spectra first reveal a very similar spectral evolution for the various brine types and pure water, with the main difference observed at the end of the dehydration with the crystallization of various hydrated minerals from brines. The main characteristic of this spectral behavior is an important decoupling between the evolution of albedo and hydration bands depths. During most of the wetting/drying processes, spectra usually display a low albedo associated with shallow water absorption band depths. Strong water absorption band depth and high albedo are respectively only observed when the surface is very wet and when the surface is very dry. These experiments can thus explain why the currently active Martian features attributed to the action of a liquid are only associated with low albedo and very weak spectral signatures. Hydration experiments also reveal that deliquescence occurs easily even at low temperature and moderate soil water vapor pressure and could thus cause seasonal darkening on Mars. These experiments demonstrate that the absence of water absorptions in CRISM in the middle afternoon does not rule out water

  2. Reactive transport modeling to study changes in water chemistry induced by CO2 injection at the Frio-I brine pilot

    Energy Technology Data Exchange (ETDEWEB)

    Kharaka, Y.K; Doughty, C.; Freifeld, B.M.; Daley, T.M.; Xu, T.

    2009-11-01

    To demonstrate the potential for geologic storage of CO{sub 2} in saline aquifers, the Frio-I Brine Pilot was conducted, during which 1600 tons of CO{sub 2} were injected into a high-permeability sandstone and the resulting subsurface plume of CO{sub 2} was monitored using a variety of hydrogeological, geophysical, and geochemical techniques. Fluid samples were obtained before CO{sub 2} injection for baseline geochemical characterization, during the CO{sub 2} injection to track its breakthrough at a nearby observation well, and after injection to investigate changes in fluid composition and potential leakage into an overlying zone. Following CO{sub 2} breakthrough at the observation well, brine samples showed sharp drops in pH, pronounced increases in HCO{sub 3}{sup -} and aqueous Fe, and significant shifts in the isotopic compositions of H{sub 2}O and dissolved inorganic carbon. Based on a calibrated 1-D radial flow model, reactive transport modeling was performed for the Frio-I Brine Pilot. A simple kinetic model of Fe release from the solid to aqueous phase was developed, which can reproduce the observed increases in aqueous Fe concentration. Brine samples collected after half a year had lower Fe concentrations due to carbonate precipitation, and this trend can be also captured by our modeling. The paper provides a method for estimating potential mobile Fe inventory, and its bounding concentration in the storage formation from limited observation data. Long-term simulations show that the CO{sub 2} plume gradually spreads outward due to capillary forces, and the gas saturation gradually decreases due to its dissolution and precipitation of carbonates. The gas phase is predicted to disappear after 500 years. Elevated aqueous CO{sub 2} concentrations remain for a longer time, but eventually decrease due to carbonate precipitation. For the Frio-I Brine Pilot, all injected CO{sub 2} could ultimately be sequestered as carbonate minerals.

  3. Reactive transport modeling to study changes in water chemistry induced by CO2 injection at the Frio-I Brine Pilot

    Science.gov (United States)

    Xu, T.; Kharaka, Y.K.; Doughty, C.; Freifeld, B.M.; Daley, T.M.

    2010-01-01

    To demonstrate the potential for geologic storage of CO2 in saline aquifers, the Frio-I Brine Pilot was conducted, during which 1600 tons of CO2 were injected into a high-permeability sandstone and the resulting subsurface plume of CO2 was monitored using a variety of hydrogeological, geophysical, and geochemical techniques. Fluid samples were obtained before CO2 injection for baseline geochemical characterization, during the CO2 injection to track its breakthrough at a nearby observation well, and after injection to investigate changes in fluid composition and potential leakage into an overlying zone. Following CO2 breakthrough at the observation well, brine samples showed sharp drops in pH, pronounced increases in HCO3- and aqueous Fe, and significant shifts in the isotopic compositions of H2O and dissolved inorganic carbon. Based on a calibrated 1-D radial flow model, reactive transport modeling was performed for the Frio-I Brine Pilot. A simple kinetic model of Fe release from the solid to aqueous phase was developed, which can reproduce the observed increases in aqueous Fe concentration. Brine samples collected after half a year had lower Fe concentrations due to carbonate precipitation, and this trend can be also captured by our modeling. The paper provides a method for estimating potential mobile Fe inventory, and its bounding concentration in the storage formation from limited observation data. Long-term simulations show that the CO2 plume gradually spreads outward due to capillary forces, and the gas saturation gradually decreases due to its dissolution and precipitation of carbonates. The gas phase is predicted to disappear after 500 years. Elevated aqueous CO2 concentrations remain for a longer time, but eventually decrease due to carbonate precipitation. For the Frio-I Brine Pilot, all injected CO2 could ultimately be sequestered as carbonate minerals. ?? 2010 Elsevier B.V.

  4. Assessment of Brine Management for Geologic Carbon Sequestration

    Energy Technology Data Exchange (ETDEWEB)

    Breunig, Hanna M. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Birkholzer, Jens T. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Borgia, Andrea [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Price, Phillip N. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Oldenburg, Curtis M. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; McKone, Thomas E. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division

    2013-06-13

    reluctant to invest in capital intensive, high risk GCS projects; early technical, economic, and environmental assessments of brine management are extremely valuable for determining the potential role of GCS in the US. We performed a first order feasibility and economic assessment, at three different locations in the US, of twelve GCS extracted-­water management options, including: geothermal energy extraction, desalination, salt and mineral harvesting, rare-­earth element harvesting, aquaculture, algae biodiesel production, road de-­icing, enhanced geothermal system (EGS) recharge, underground reinjection, landfill disposal, ocean disposal, and evaporation pond disposal. Three saline aquifers from different regions of the US were selected as hypothetical GCS project sites to encompass variation in parameters that are relevant to the feasibility and economics of brine disposal. The three aquifers are the southern Mt. Simon Sandstone Formation in the Illinois Basin, IL; the Vedder Formation in the southern San Joaquin Basin, CA; and the Jasper Interval in the eastern Texas Gulf Basin, TX. These aquifers are candidates for GCS due to their physical characteristics and their close proximity to large CO2 emission sources. Feasibility and impacts were calculated using one mt-­CO2 injected as the functional unit of brine management. Scenarios were performed for typical 1000MW coal-­fired power plants (CFPP) that incurred an assumed 24 percent carbon capture energy penalty (EP), injected 90 percent of CO2 emissions (~9 million mt-­ CO2 injected annually), and treated extracted water onsite. Net present value (NPV), land requirements, laws and regulations, and technological limits were determined for each stage of disposal, and used to estimate feasibility. The boundary of the assessment began once extracted water was brought to the surface, and ended once the water evaporated,

  5. Gas content of Gladys McCall reservoir brine

    Energy Technology Data Exchange (ETDEWEB)

    Hayden, C.G.; Randolph, P.L.

    1987-05-29

    On October 8, 1983, after the first full day of production from Sand No.8 in the Gladys McCall well, samples of separator gas and separator brine were collected for laboratory P-V-T (pressure, volume, temperature) studies. Recombination of amounts of these samples based upon measured rates at the time of sample collection, and at reservoir temperature (290 F), revealed a bubble point pressure of 9200 psia. This is substantially below the reported reservoir pressure of 12,783 psia. The gas content of the recombined fluids was 30.19 SCF of dry gas/STB of brine. In contrast, laboratory studies indicate that 35.84 SCF of pure methane would dissolve in each STB of 95,000 mg/L sodium chloride brine. These results indicate that the reservoir brine was not saturated with natural gas. By early April, 1987, production of roughly 25 million barrels of brine had reduced calculated flowing bottomhole pressure to about 6600 psia at a brine rate of 22,000 STB/D. If the skin factor(s) were as high as 20, flowing pressure drop across the skin would still be only about 500 psi. Thus, some portion of the reservoir volume was believed to have been drawn down to below the bubble point deduced from the laboratory recombination of separator samples. When the pressure in a geopressured geothermal reservoir is reduced to below the bubble point pressure for solution gas, gas is exsolved from the brine flowing through the pores in the reservoir rock. This exsolved gas is trapped in the reservoir until the fractional gas saturation of pore volume becomes large enough for gas flow to commence through a continuous gas-filled channel. At the same time, the gas/brine ratio becomes smaller and the chemistry of the remaining solution gas changes for the brine from which gas is exsolved. A careful search was made for the changes in gas/brine ratio or solution gas chemistry that would accompany pressure dropping below the bubble point pressure. Changes of about the same magnitude as the scatter in

  6. The determination of vanadium in brines by atomic absorption spectroscopy

    Science.gov (United States)

    Crump-Wiesner, Hans J.; Feltz, H.R.; Purdy, W.C.

    1971-01-01

    A standard addition method is described for the determination of vanadium in brines by atomic absorption spectroscopy with a nitrous oxide-acetylene flame. Sample pH is adjusted to 1.0 with concentrated hydrochloric acid and the vanadium is directly extracted with 5% cupferron in methyl isobutyl ketone (MIBK). The ketone layer is then aspirated into the flame and the recorded absorption values are plotted as a function of the concentration of the added metal. As little as 2.5 ??g l-1 of vanadium can be detected under the conditions of the procedure. Tungsten and tin interfere when present in excess of 5 and 10 ??g ml-1, respectively. The concentrations of the two interfering ions normally found in brines are well below interference levels. ?? 1971.

  7. Chemical Composition and Enzymes Inhibitory, Brine Shrimp Larvae Toxicity, Antimicrobial and Antioxidant Activities of Caloplaca biatorina

    Directory of Open Access Journals (Sweden)

    Tahereh Valadbeigi

    2016-10-01

    Full Text Available Background This study evaluated the brine shrimp larvae toxicity and enzymes inhibitory especially anti-diabetic potential of Caloplaca biatorina via in vitro inhibition of α-amylase and α-glucosidase using the methanol extracts. Also aldehyde oxidase and xanthine oxidase enzymes inhibitory, cytotoxicity, and antioxidant activities of the species were determined. Methods In this experimental study, different concentrations of the extracts (0.2, 5.0, 1 and 1.5 mg/mL were incubated with enzyme substrate solution and the percentage of enzyme inhibitory activity and IC50 was calculated. Folin- Ciocalteu reagent and aluminium chloride colorimetric methods were used to estimate total phenolic and flavonoid content of extracts. The toxicity of the extract was assessed using the brine shrimp lethality bioassay. The minimal inhibitory concentration (MIC and minimum bactericidal concentration (MBC were determined. High-performance liquid chromatography and Thin-layer chromatography analysis were evaluated. The data were analyzed by SPSS V.21 software. Results Parietin, Emodin, 1,8-Dihydroxy-3-(hydroxymethyl-6- methoxy-9.10-anthracenedione and Rhein were identified. The extract showed strong α-glucosidase, aldehyde oxidase and xanthine oxidase inhibitory activities with IC50 value of 17.12, 40.09 and 11.02 µg/mL respectively. Also methanol extract displayed the strongest DPPH radical scavenging and brine shrimp toxicity (IC50 = 91.11 properties. Conclusions The result obtained suggests that the C. biatorina extract can be classified as non-toxic. Also, it revealed the antioxidant and antidiabetic potential of the lichen.

  8. The fate of Listeria monocytogenes in brine and on Gouda cheese following artificial contamination during brining

    NARCIS (Netherlands)

    Wemmenhove, E.; Beumer, R.R.; Hooijdonk, van A.C.M.; Zwietering, M.H.; Wells-Bennik, M.H.J.

    2014-01-01

    The fate of 3 different Listeria monocytogenes strains (Scott A, 2F and 6E) was studied independently in brine and on factory-scale Gouda cheeses that had been submerged in brine that was artificially contaminated with these individual strains. Viable numbers of L. monocytogenes in the brine

  9. Factors Impeding Enzymatic Wheat Gluten Hydrolysis at High Solid Concentrations

    NARCIS (Netherlands)

    Hardt, N.A.; Janssen, A.E.M.; Boom, R.M.; Goot, van der A.J.

    2014-01-01

    Enzymatic wheat gluten hydrolysis at high solid concentrations is advantageous from an environmental and economic point of view. However, increased wheat gluten concentrations result in a concentration effect with a decreased hydrolysis rate at constant enzyme-to-substrate ratios and a decreased

  10. Effect of brine marination on survival and growth of spoilage and pathogenic bacteria during processing and subsequent storage of ready-to-eat shrimp (Pandalus borealis)

    DEFF Research Database (Denmark)

    Mejlholm, Ole; Devitt, Tina D.; Dalgaard, Paw

    2012-01-01

    and growth during processing and subsequent storage of brined and drained shrimp in modified atmosphere packaging (MAP). Different brines with (i) acetic and lactic acids (AL) or (ii) benzoic, citric and sorbic acids (BCS) were studied. V. parahaemolyticus was inactivated in brine AL without shrimp whereas...... of the examined pathogens was able to grow at 7°C in brined and drained MAP shrimp that resembled commercial products. However, reducing the concentration of acetic and lactic acids by 50% resulted in relatively fast growth of L. monocytogenes in brined and drained MAP shrimp at 7°C. Growth of S. aureus...... and Salmonella was observed in similar products stored at 15°C. V. parahaemolyticus was reduced in brined and drained MAP shrimp stored at both 7 and 15°C. Based on the results of the present study, L. monocytogenes was identified as the greatest potential risk with respect to the safety of brined and drained...

  11. On the physico-chemical characteristics of brines

    Digital Repository Service at National Institute of Oceanography (India)

    Shirodkar, P.V.; Rao, P.V.S.S.D.P.; Singbal, S.Y.S.

    Analyses of the natural brines form the salt lakes, salt pans and the artificial brines obtained after the solar desalination of seawater respectively, showed wide differences in their physico-chemical characteristics. The natural brines are markEd...

  12. Refractive Secondary Solar Concentrator Demonstrated High-Temperature Operation

    Science.gov (United States)

    Wong, Wayne A.

    2002-01-01

    Space applications that utilize solar thermal energy--such as electric power conversion systems, thermal propulsion systems, and furnaces--require highly efficient solar concentration systems. The NASA Glenn Research Center is developing the refractive secondary concentrator, which uses refraction and total internal reflection to efficiently concentrate and direct solar energy. When used in combination with advanced lightweight primary concentrators, such as inflatable thin films, the refractive secondary concentrator enables very high system concentration ratios and very high temperatures. Last year, Glenn successfully demonstrated a secondary concentrator throughput efficiency of 87 percent, with a projected efficiency of 93 percent using an antireflective coating. Building on this achievement, Glenn recently successfully demonstrated high-temperature operation of the secondary concentrator when it was used to heat a rhenium receiver to 2330 F. The high-temperature demonstration of the concentrator was conducted in Glenn's 68-ft long Tank 6 thermal vacuum facility equipped with a solar simulator. The facility has a rigid panel primary concentrator that was used to concentrate the light from the solar simulator onto the refractive secondary concentrator. NASA Marshall Space Flight Center provided a rhenium cavity, part of a solar thermal propulsion engine, to serve as the high-temperature receiver. The prototype refractive secondary concentrator, measuring 3.5 in. in diameter and 11.2 in. long, is made of single-crystal sapphire. A water-cooled splash shield absorbs spillage light outside of the 3.5-in. concentrator aperture. Multilayer foil insulation composed of tungsten, molybdenum, and niobium is used to minimize heat loss from the hightemperature receiver. A liquid-cooled canister calorimeter is used to measure the heat loss through the multilayer foil insulation.

  13. Selenium biotransformations in an engineered aquatic ecosystem for bioremediation of agricultural wastewater via brine shrimp production.

    Science.gov (United States)

    Schmidt, Radomir; Tantoyotai, Prapakorn; Fakra, Sirine C; Marcus, Matthew A; Yang, Soo In; Pickering, Ingrid J; Bañuelos, Gary S; Hristova, Krassimira R; Freeman, John L

    2013-05-21

    An engineered aquatic ecosystem was specifically designed to bioremediate selenium (Se), occurring as oxidized inorganic selenate from hypersalinized agricultural drainage water while producing brine shrimp enriched in organic Se and omega-3 and omega-6 fatty acids for use in value added nutraceutical food supplements. Selenate was successfully bioremediated by microalgal metabolism into organic Se (seleno-amino acids) and partially removed via gaseous volatile Se formation. Furthermore, filter-feeding brine shrimp that accumulated this organic Se were removed by net harvest. Thriving in this engineered pond system, brine shrimp ( Artemia franciscana Kellogg) and brine fly (Ephydridae sp.) have major ecological relevance as important food sources for large populations of waterfowl, breeding, and migratory shore birds. This aquatic ecosystem was an ideal model for study because it mimics trophic interactions in a Se polluted wetland. Inorganic selenate in drainage water was metabolized differently in microalgae, bacteria, and diatoms where it was accumulated and reduced into various inorganic forms (selenite, selenide, or elemental Se) or partially incorporated into organic Se mainly as selenomethionine. Brine shrimp and brine fly larva then bioaccumulated Se from ingesting aquatic microorganisms and further metabolized Se predominately into organic Se forms. Importantly, adult brine flies, which hatched from aquatic larva, bioaccumulated the highest Se concentrations of all organisms tested.

  14. Fabrication and tolerances of optics for high concentration photovoltaics

    OpenAIRE

    Benitez Gimenez, Pablo; Miñano Dominguez, Juan Carlos; Ahmadpanaih, Hamed; Mendes Lopes, Joao; Zamora Herranz, Pablo

    2014-01-01

    High Concentration Photovoltaics (HCPV) require an optical system with high efficiency, low cost and large tolerance. We describe the particularities of the HCPV applications, which constrain the optics design and the manufacturing techonologies.

  15. Analysis of anions in geological brines using ion chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Merrill, R.M.

    1985-03-01

    Ion chromatographic procedures for the determination of the anions bromide, sulfate, nitrite, nitrate, phosphate, and iodide in brine samples have been developed and are described. The techniques have been applied to the analysis of natural brines, and geologic evaporites. Sample matrices varied over a range from 15,000 mg/L to 200,000 mg/L total halogens, nearly all of which is chloride. The analyzed anion concentrations ranged from less than 5 mg/L in the cases of nitrite, nitrate, and phosphate, to 20,000 mg/L in the case of sulfate. A technique for suppressing chloride and sulfate ions to facilitate the analysis of lower concentration anions is presented. Analysis times are typically less than 20 minutes for each procedure and the ion chromatographic results compare well with those obtained using more time consuming classical chemical analyses. 10 references, 14 figures.

  16. Microbial community of the deep-sea brine Lake Kryos seawater-brine interface is active below the chaotropicity limit of life as revealed by recovery of mRNA.

    Science.gov (United States)

    Yakimov, Michail M; La Cono, Violetta; Spada, Gina L; Bortoluzzi, Giovanni; Messina, Enzo; Smedile, Francesco; Arcadi, Erika; Borghini, Mireno; Ferrer, Manuel; Schmitt-Kopplin, Phillippe; Hertkorn, Norbert; Cray, Jonathan A; Hallsworth, John E; Golyshin, Peter N; Giuliano, Laura

    2015-02-01

    Within the complex of deep, hypersaline anoxic lakes (DHALs) of the Mediterranean Ridge, we identified a new, unexplored DHAL and named it 'Lake Kryos' after a nearby depression. This lake is filled with magnesium chloride (MgCl2 )-rich, athalassohaline brine (salinity > 470 practical salinity units), presumably formed by the dissolution of Messinian bischofite. Compared with the DHAL Discovery, it contains elevated concentrations of kosmotropic sodium and sulfate ions, which are capable of reducing the net chaotropicily of MgCl2 -rich solutions. The brine of Lake Kryos may therefore be biologically permissive at MgCl2 concentrations previously considered incompatible with life. We characterized the microbiology of the seawater-Kryos brine interface and managed to recover mRNA from the 2.27-3.03 M MgCl2 layer (equivalent to 0.747-0.631 water activity), thereby expanding the established chaotropicity window-for-life. The primary bacterial taxa present there were Kebrit Deep Bacteria 1 candidate division and DHAL-specific group of organisms, distantly related to Desulfohalobium. Two euryarchaeal candidate divisions, Mediterranean Sea Brine Lakes group 1 and halophilic cluster 1, accounted for > 85% of the rRNA-containing archaeal clones derived from the 2.27-3.03 M MgCl2 layer, but were minority community-members in the overlying interface-layers. These findings shed light on the plausibility of life in highly chaotropic environments, geochemical windows for microbial extremophiles, and have implications for habitability elsewhere in the Solar System. © 2014 Society for Applied Microbiology and John Wiley & Sons Ltd.

  17. Isolation and identification of oxidation products of syringol from brines and heated meat matrix.

    Science.gov (United States)

    Bölicke, Sarah-Maria; Ternes, Waldemar

    2016-08-01

    In this study we developed new extraction and detection methods (using HPLC-UV and LC-MS), making it possible to analyze the smoke phenol syringol and its oxidation products nitrososyringol, nitrosyringol, and the syringol dimer 3,3',5,5'-tetramethoxy-1,1'-biphenyl-4,4'-diol, which were identified in heated meat for the first time. Preliminary brine experiments performed with different concentrations of ascorbic acid showed that high amounts of this antioxidant also resulted in almost complete degradation of syringol and to formation of the oxidation products when the brines were heated at low pH values. Heat treatment (80°C) and subsequent simulated digestion applied to meat samples containing syringol, ascorbic acid and different concentrations of sodium nitrite produced 3,3',5,5'-tetramethoxy-1,1'-biphenyl-4,4'-diol even at a low nitrite level in the meat matrix, while nitroso- and nitrosyringol were isolated only after the digestion experiments. Increasing amounts of oxygen in the meat matrix decreased the syringol concentration and enhanced the formation of the reaction products in comparison to the samples without added oxygen. Copyright © 2016 Elsevier Ltd. All rights reserved.

  18. Weeks Island brine diffuser site study: baseline conditions and environmental assessment technical report

    Energy Technology Data Exchange (ETDEWEB)

    None

    1980-12-12

    This technical report presents the results of a study conducted at two alternative brine diffuser sites (A and B) proposed for the Weeks Island salt dome, together with an analysis of the potential physical, chemical, and biological effects of brine disposal for this area of the Gulf of Mexico. Brine would result from either the leaching of salt domes to form or enlarge oil storage caverns, or the subsequent use of these caverns for crude oil storage in the Strategic Petroleum Reserve (SPR) program. Brine leached from the Weeks Island salt dome would be transported through a pipeline which would extend from the salt dome either 27 nautical miles (32 statute miles) for Site A, or 41 nautical miles (47 statute miles) for Site B, into Gulf waters. The brine would be discharged at these sites through an offshore diffuser at a sustained peak rate of 39 ft/sup 3//sec. The disposal of large quantities of brine in the Gulf could have a significant impact on the biology and water quality of the area. Physical and chemical measurements of the marine environment at Sites A and B were taken between September 1977 and July 1978 to correlate the existing environmental conditions with the estimated physical extent of tthe brine discharge as predicted by the MIT model (US Dept. of Commerce, 1977a). Measurements of wind, tide, waves, currents, and stratification (water column structure) were also obtained since the diffusion and dispersion of the brine plume are a function of the local circulation regime. These data were used to calculate both near- and far-field concentrations of brine, and may also be used in the design criteria for diffuser port configuration and verification of the plume model. Biological samples were taken to characterize the sites and to predict potential areas of impact with regard to the discharge. This sampling focused on benthic organisms and demersal fish. (DMC)

  19. Brine shrimp cytotoxic activities of Hippophae rhamnoides Linn leaves extracts

    Institute of Scientific and Technical Information of China (English)

    JavidAli; BashirAhmad

    2015-01-01

    Objective: To evaluate brine shrimp lethality assay of solvent extracts (aqueous, methanol, ethanol, acetone, ethyl acetate, chloroform and n-hexane) of Hippophae rhamnoides (H. rhamnoides) leaves. Methods: Brine shrimp cytotoxicity assay was used to assess the cytotoxic potential of H. rhamnoides leaves extracts. Three vials for concentration of each extract were made and 10 shrimps per vial (30 shrimps per dilution) were transferred to specific concentration of each extract. Results: The mortality of aqueous extract was 46.7%, methanol extract was 46.7%, ethanolic extract was 50.0%, ethyl acetate was 26.7%, acetone extract was 33.3%, chloroform extract was 40.0% and n-hexane extract was 33.3%. The lowest LD50 was found in methanol extracts (1199.97 µg/mL). Brine shrimp cytotoxicity of tested extracts of H. rhamnoides showed that mortality rate was concentration dependent. Conclusions: It is concluded that bioactive components are present in all leaves extracts of H. rhamnoides, which could be accounted for its pharmacological effects. Thus, the results support the uses of this plant species in traditional medicine.

  20. The Effect of adjusting PH on Stretchability and Meltability to White Brined Nabulsi Cheese

    Directory of Open Access Journals (Sweden)

    Ayman S. Mazahreh

    2009-01-01

    Full Text Available Problem statement: Boiled white brined (Nabulsi cheese is the mostly consumed in Jordan; this cheese should show meltability and high stretchability in order to fit in the production of high quality Kunafa and other popular local sweets and pastries.The most outstanding characteristic of Nabulsi cheese is the long keeping ability (more than one year without cooling, since it is preserved in concentrated brine (up to 25%. Approach: This work was based on the hypothesis that it would be possible to imply meltability and stretchability to the cheese by adjusting pH to the original brine that may specifically act on cross linking bonds of casein. A new apparatus for measuring the actual stretchability was designed and constructed; measurements on different cheeses proved its validity and reliability to measurement stretchability up to 80cm. Detailed treatments revealed the success of the proposed assumption in inducing meltability and stretchability to cheese processed and preserved according to the traditional methods. Results: The following results were obtained: It is possible to imply a low but acceptable level of stretchability and meltability through adjustment of the pH in the range of 5.4-5.8 by adding calculated amount of citric acid considering the buffering capacity of the cheese and storing it for few weeks to reach equilibrium. Conclusion: Conformational experiments proved the applicability of the new method on commercial Nabulsi cheese samples. Sensory evaluation revealed the superiority of pH adjusting treatment specifically at pH 5.4 and 5.8 as well as commercial Mashmouleh cheese that has high meltability and stretchability when used in Kunafa making.

  1. Bead Evaporator for Complete Water and Salt Recovery from Brine Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A microgravity-compatible Brine Evaporation and Mineralization System (BEMS) is proposed for 100% water recovery from highly contaminated wastewater as well as water...

  2. USE OF REJECT BRINE FROM DESALINATION ON DIFFERENT DEVELOPMENT STAGES OF HYDROPONIC LETTUCE

    National Research Council Canada - National Science Library

    NILDO DA SILVA DIAS; FRANCISCO AÉCIO DE LIMA; CLÁUDIO RICARDO DA SILVA; OSVALDO NOGUEIRA DE SOUSA NETO; HANS RAJ GHEYI

    2011-01-01

    In order to evaluated the impact of the high salinity reject brine from reverse osmosis desalination on hydroponics lettuce cultivated in greenhouse an investigation was carried out in Mossoro, Northeast of Brazil (5º11...

  3. Study and Test of Process of Production of Potassium Chloride from High Calcium Potassium Bearing Brine in Salt Lake%利用盐湖高钙含钾卤水制取氯化钾工艺试验研究

    Institute of Scientific and Technical Information of China (English)

    朱晓东; 郑秀洁

    2011-01-01

    In some of chloride - type brine in Salt Lake of Qinghai. The cycling accumulation of calcium results in increasing growth of its concetration, which probably will make some effect on the production of potassium chloride from brine. This paper makes research on impact this type of high calcium potassium bearing brine has on production of potassium chloride by 4# Process . The research results show that calcium content in brine would have less impact on production of potassium chloride by 4# Process.%青海盐湖部分氯化物型卤水中,由于钙的循环积累,其浓度不断增高,这可能对从卤水中提取氯化钾带来一定影响.实验研究了该类型高钙含钾卤水对4#工艺制取氯化钾的影响,研究结果表明卤水中钙含量对4#工艺制取氯化钾影响较小.

  4. Utilization of Brine Sludge in Nonstructural Building Components: A Sustainable Approach

    Directory of Open Access Journals (Sweden)

    Mridul Garg

    2014-01-01

    Full Text Available The characterization and influence of brine sludge on the properties of cement-fly ash-sludge binders are presented. The reaction products formed during the hydration of binder provide an interlocking framework to physically encapsulate the waste particles and are responsible for the development of strength. The utilization of brine sludge in making paver blocks and bricks and the effect of sludge concentration on the engineering properties of these products are also discussed. These results clearly exhibited that brine sludge up to 35 and 25% can safely be utilized for making paver blocks and bricks, respectively. The leachability studies confirm that the metals ions and impurities in the sludge are substantially fixed in the matrix and do not readily leach from there. The utilization of brine sludge in construction materials could serve as an alternative solution to disposal and reduce pollution.

  5. Sampling of brine in cores of Precambrian granite from northern Illinois

    Science.gov (United States)

    Couture, Rex A.; Seitz, Martin G.; Steindler, Martin J.

    1983-09-01

    The composition of groundwater in deep-seated rocks is of great interest, both geochemically and in connection with the disposal of radioactive waste. However, sampling of deep-seated groundwater is expensive and often difficult. We describe here a simple technique for the elution of pore fluid (groundwater) from cores of igneous rocks, and we describe brine eluted from a core of Precambrian granite from Northern Illinois drill hole UPH-3. The brine is predominantly NaCl and CaCl2, with a Ca/Na mole ratio of about 0.05 to 0.1. From analysis of soluble chloride in a crushed sample the chloride concentration in the pore water is estimated as 2.3 M. The brine is similar to brine in the Illinois Basin, and it was probably derived from the overlying sediments.

  6. Synthesis of hydroxy sodalite from coal fly ash using waste industrial brine solution.

    Science.gov (United States)

    Musyoka, Nicholas M; Petrik, Leslie F; Balfour, Gillian; Gitari, Wilson M; Hums, Eric

    2011-01-01

    The effect of using industrial waste brine solution instead of ultra pure water was investigated during the synthesis of zeolites using three South African coal fly ashes as Si feedstock. The high halide brine was obtained from the retentate effluent of a reverse osmosis mine water treatment plant. Synthesis conditions applied were; ageing of fly ash was at 47 ° C for 48 hours, and while the hydrothermal treatment temperature was set at 140 ° C for 48 hours. The use of brine as a solvent resulted in the formation of hydroxy sodalite zeolite although unconverted mullite and hematite from the fly ash feedstock was also found in the synthesis product.

  7. Effects of plant downtime on the microbial community composition in the highly saline brine of a geothermal plant in the North German Basin.

    Science.gov (United States)

    Westphal, Anke; Lerm, Stephanie; Miethling-Graff, Rona; Seibt, Andrea; Wolfgramm, Markus; Würdemann, Hilke

    2016-04-01

    The microbial biocenosis in highly saline fluids produced from the cold well of a deep geothermal heat store located in the North German Basin was characterized during regular plant operation and immediately after plant downtime phases. Genetic fingerprinting revealed the dominance of sulfate-reducing bacteria (SRB) and fermentative Halanaerobiaceae during regular plant operation, whereas after shutdown phases, sequences of sulfur-oxidizing bacteria (SOB) were also detected. The detection of SOB indicated oxygen ingress into the well during the downtime phase. High 16S ribosomal RNA (rRNA) and dsrA gene copy numbers at the beginning of the restart process showed an enrichment of bacteria, SRB, and SOB during stagnant conditions consistent with higher concentrations of dissolved organic carbon (DOC), sulfate, and hydrogen sulfide in the produced fluids. The interaction of SRB and SOB during plant downtimes might have enhanced the corrosion processes occurring in the well. It was shown that scale content of fluids was significantly increased after stagnant phases. Moreover, the sulfur isotopic signature of the mineral scales indicated microbial influence on scale formation.

  8. Viruses-to-mobile genetic elements skew in the deep Atlantis II brine pool sediments

    KAUST Repository

    Adel, Mustafa

    2016-09-06

    The central rift of the Red Sea has 25 brine pools with different physical and geochemical characteristics. Atlantis II (ATIID), Discovery Deeps (DD) and Chain Deep (CD) are characterized by high salinity, temperature and metal content. Several studies reported microbial communities in these brine pools, but few studies addressed the brine pool sediments. Therefore, sediment cores were collected from ATIID, DD, CD brine pools and an adjacent brine-influenced site. Sixteen different lithologic sediment sections were subjected to shotgun DNA pyrosequencing to generate 1.47 billion base pairs (1.47 × 109 bp). We generated sediment-specific reads and attempted to annotate all reads. We report the phylogenetic and biochemical uniqueness of the deepest ATIID sulfur-rich brine pool sediments. In contrary to all other sediment sections, bacteria dominate the deepest ATIID sulfur-rich brine pool sediments. This decrease in virus-to-bacteria ratio in selected sections and depth coincided with an overrepresentation of mobile genetic elements. Skewing in the composition of viruses-to-mobile genetic elements may uniquely contribute to the distinct microbial consortium in sediments in proximity to hydrothermally active vents of the Red Sea and possibly in their surroundings, through differential horizontal gene transfer.

  9. Viruses-to-mobile genetic elements skew in the deep Atlantis II brine pool sediments.

    Science.gov (United States)

    Adel, Mustafa; Elbehery, Ali H A; Aziz, Sherry K; Aziz, Ramy K; Grossart, Hans-Peter; Siam, Rania

    2016-09-06

    The central rift of the Red Sea has 25 brine pools with different physical and geochemical characteristics. Atlantis II (ATIID), Discovery Deeps (DD) and Chain Deep (CD) are characterized by high salinity, temperature and metal content. Several studies reported microbial communities in these brine pools, but few studies addressed the brine pool sediments. Therefore, sediment cores were collected from ATIID, DD, CD brine pools and an adjacent brine-influenced site. Sixteen different lithologic sediment sections were subjected to shotgun DNA pyrosequencing to generate 1.47 billion base pairs (1.47 × 10(9) bp). We generated sediment-specific reads and attempted to annotate all reads. We report the phylogenetic and biochemical uniqueness of the deepest ATIID sulfur-rich brine pool sediments. In contrary to all other sediment sections, bacteria dominate the deepest ATIID sulfur-rich brine pool sediments. This decrease in virus-to-bacteria ratio in selected sections and depth coincided with an overrepresentation of mobile genetic elements. Skewing in the composition of viruses-to-mobile genetic elements may uniquely contribute to the distinct microbial consortium in sediments in proximity to hydrothermally active vents of the Red Sea and possibly in their surroundings, through differential horizontal gene transfer.

  10. Viruses-to-mobile genetic elements skew in the deep Atlantis II brine pool sediments

    Science.gov (United States)

    Adel, Mustafa; Elbehery, Ali H. A.; Aziz, Sherry K.; Aziz, Ramy K.; Grossart, Hans-Peter; Siam, Rania

    2016-09-01

    The central rift of the Red Sea has 25 brine pools with different physical and geochemical characteristics. Atlantis II (ATIID), Discovery Deeps (DD) and Chain Deep (CD) are characterized by high salinity, temperature and metal content. Several studies reported microbial communities in these brine pools, but few studies addressed the brine pool sediments. Therefore, sediment cores were collected from ATIID, DD, CD brine pools and an adjacent brine-influenced site. Sixteen different lithologic sediment sections were subjected to shotgun DNA pyrosequencing to generate 1.47 billion base pairs (1.47 × 109 bp). We generated sediment-specific reads and attempted to annotate all reads. We report the phylogenetic and biochemical uniqueness of the deepest ATIID sulfur-rich brine pool sediments. In contrary to all other sediment sections, bacteria dominate the deepest ATIID sulfur-rich brine pool sediments. This decrease in virus-to-bacteria ratio in selected sections and depth coincided with an overrepresentation of mobile genetic elements. Skewing in the composition of viruses-to-mobile genetic elements may uniquely contribute to the distinct microbial consortium in sediments in proximity to hydrothermally active vents of the Red Sea and possibly in their surroundings, through differential horizontal gene transfer.

  11. Numerical simulations of lab-scale brine-water mixing experiments.

    Energy Technology Data Exchange (ETDEWEB)

    Khalil, Imane; Webb, Stephen Walter

    2006-10-01

    Laboratory-scale experiments simulating the injection of fresh water into brine in a Strategic Petroleum Reserve (SPR) cavern were performed at Sandia National Laboratories for various conditions of injection rate and small and large injection tube diameters. The computational fluid dynamic (CFD) code FLUENT was used to simulate these experiments to evaluate the predictive capability of FLUENT for brine-water mixing in an SPR cavern. The data-model comparisons show that FLUENT simulations predict the mixing plume depth reasonably well. Predictions of the near-wall brine concentrations compare very well with the experimental data. The simulated time for the mixing plume to reach the vessel wall was underpredicted for the small injection tubes but reasonable for the large injection tubes. The difference in the time to reach the wall is probably due to the three-dimensional nature of the mixing plume as it spreads out at the air-brine or oil-brine interface. The depth of the mixing plume as it spreads out along the interface was within a factor of 2 of the experimental data. The FLUENT simulation results predict the plume mixing accurately, especially the water concentration when the mixing plume reaches the wall. This parameter value is the most significant feature of the mixing process because it will determine the amount of enhanced leaching at the oil-brine interface.

  12. Intercomparison of passive microwave sea ice concentration retrievals over the high-concentration Arctic sea ice

    DEFF Research Database (Denmark)

    andersen, susanne; Tonboe, R.; Kaleschke, L.

    2007-01-01

    [1] Measurements of sea ice concentration from the Special Sensor Microwave Imager (SSM/I) using seven different algorithms are compared to ship observations, sea ice divergence estimates from the Radarsat Geophysical Processor System, and ice and water surface type classification of 59 wide......-swath synthetic aperture radar (SAR) scenes. The analysis is confined to the high-concentration Arctic sea ice, where the ice cover is near 100%. During winter the results indicate that the variability of the SSM/I concentration estimates is larger than the true variability of ice concentration. Results from...... a trusted subset of the SAR scenes across the central Arctic allow the separation of the ice concentration uncertainty due to emissivity variations and sensor noise from other error sources during the winter of 2003-2004. Depending on the algorithm, error standard deviations from 2.5 to 5.0% are found...

  13. High Stokes shift perylene dyes for luminescent solar concentrators.

    Science.gov (United States)

    Sanguineti, Alessandro; Sassi, Mauro; Turrisi, Riccardo; Ruffo, Riccardo; Vaccaro, Gianfranco; Meinardi, Francesco; Beverina, Luca

    2013-02-25

    Highly efficient plastic based single layer Luminescent Solar Concentrators (LSCs) require the design of luminophores having complete spectral separation between absorption and emission spectra (large Stokes shift). We describe the design, synthesis and characterization of a new perylene dye possessing Stokes shift as high as 300 meV, fluorescent quantum yield in the LSC slab of 70% and high chemical and photochemical stability.

  14. Hair and toenail arsenic concentrations of residents living in areas with high environmental arsenic concentrations.

    OpenAIRE

    Hinwood, Andrea L; Sim, Malcolm R; Jolley, Damien; de Klerk, Nick; Bastone, Elisa B; Gerostamoulos, Jim; Drummer, Olaf H

    2003-01-01

    Surface soil and groundwater in Australia have been found to contain high concentrations of arsenic. The relative importance of long-term human exposure to these sources has not been established. Several studies have investigated long-term exposure to environmental arsenic concentrations using hair and toenails as the measure of exposure. Few have compared the difference in these measures of environmental sources of exposure. In this study we aimed to investigate risk factors for elevated hai...

  15. The Brine Shrimp's Butterfly Stroke

    CERN Document Server

    Johnson, Brennan; Dasi, Lakshmi Prasad

    2011-01-01

    We investigate the fluid dynamics of brine shrimp larvae swimming in this gallery of fluid motion video. Time resolved particle image velocimetry was performed using nano-particles as seeding material to measure the time dependent velocity and vorticity fields. The Reynolds number of the flow was roughly 8 and the Womerseley number (ratio of periodic forcing to viscous forcing) was about 5. Vorticity dynamics reveals the formation of a vortex ring structure at the tip of each arm at the beginning of the power stroke. This two vortex system evolves dramatically with time as the stroke progresses. The outer circulation is noted to weaken while the inner circulation strengthens over the power stroke. The gaining strength of the inner vortex correlates with the acceleration and forward movement of the larvae.

  16. Study of brine treatment. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1977-11-01

    Available information pertinent to the treatment of geothermal brines was collected by literature search and then evaluated and summarized for use by the electric utility and geothermal industries. The information was screened from the geothermal, oil and gas, wastewater disposal, and boiler water treatment industries. The current state of knowledge and methodology concerning the treatment of geothermal brines to control scaling and corrosion in geothermal electric power production was assessed. Currently, geothermal scale in pipes and wells is removed by physical or chemical methods. There is a growing effort on developing methods to control scale formation for both fresh and spent brines, including pH adjustment and application of an electrical potential for fresh fluids, and coagulation to treat spent fluids. Current methods of corrosion control center around planned replacement of piping and other plant components, with efforts focused primarily on development of materials with improved corrosion resistance. Recommendations for additional work to improve brine treatment include the following: (1) chemical and physical characterization of brine and scale compositions, (2) basic data on the mechanism of scale formation and the effects of inhibitors, (3) development of instrumentation to monitor geothermal brine constituents, (4) correlation of laboratory results with field test data, and (5) screening of currently available commercial inhibitors for application to geothermal brines. An annotated bibliography of the reference material used in this study is included.

  17. Applications of nonimaging optics for very high solar concentrations

    Energy Technology Data Exchange (ETDEWEB)

    O`Gallagher, J.; Winston, R.

    1997-12-31

    Using the principles and techniques of nonimaging optics, solar concentrations that approach the theoretical maximum can be achieved. This has applications in solar energy collection wherever concentration is desired. In this paper, we survey recent progress in attaining and using high and ultrahigh solar fluxes. We review a number of potential applications for highly concentrated solar energy and the current status of the associated technology. By making possible new and unique applications for intense solar flux, these techniques have opened a whole new frontier for research and development of potentially economic uses of solar energy.

  18. Buoyancy effects on upward brine displacement caused by CO2 injection

    Energy Technology Data Exchange (ETDEWEB)

    Oldenburg, C.M.; Rinaldi, A.

    2010-01-15

    Upward displacement of brine from deep reservoirs driven by pressure increases resulting from CO{sub 2} injection for geologic carbon sequestration may occur through improperly sealed abandoned wells, through permeable faults, or through permeable channels between pinch-outs of shale formations. The concern about upward brine flow is that, upon intrusion into aquifers containing groundwater resources, the brine may degrade groundwater. Because both salinity and temperature increase with depth in sedimentary basins, upward displacement of brine involves lifting fluid that is saline but also warm into shallower regions that contain fresher, cooler water. We have carried out dynamic simulations using TOUGH2/EOS7 of upward displacement of warm, salty water into cooler, fresher aquifers in a highly idealized two-dimensional model consisting of a vertical conduit (representing a well or permeable fault) connecting a deep and a shallow reservoir. Our simulations show that for small pressure increases and/or high-salinity-gradient cases, brine is pushed up the conduit to a new static steady-state equilibrium. On the other hand, if the pressure rise is large enough that brine is pushed up the conduit and into the overlying upper aquifer, flow may be sustained if the dense brine is allowed to spread laterally. In this scenario, dense brine only contacts the lower-most region of the upper aquifer. In a hypothetical case in which strong cooling of the dense brine occurs in the upper reservoir, the brine becomes sufficiently dense that it flows back down into the deeper reservoir from where it came. The brine then heats again in the lower aquifer and moves back up the conduit to repeat the cycle. Parameter studies delineate steady-state (static) and oscillatory solutions and reveal the character and period of oscillatory solutions. Such oscillatory solutions are mostly a curiosity rather than an expected natural phenomenon because in nature the geothermal gradient prevents the

  19. Assessment of Brine Management for Geologic Carbon Sequestration

    Energy Technology Data Exchange (ETDEWEB)

    Breunig, Hanna M. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Birkholzer, Jens T. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Borgia, Andrea [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Price, Phillip N. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Oldenburg, Curtis M. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; McKone, Thomas E. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division

    2013-06-13

    reluctant to invest in capital intensive, high risk GCS projects; early technical, economic, and environmental assessments of brine management are extremely valuable for determining the potential role of GCS in the US. We performed a first order feasibility and economic assessment, at three different locations in the US, of twelve GCS extracted-­water management options, including: geothermal energy extraction, desalination, salt and mineral harvesting, rare-­earth element harvesting, aquaculture, algae biodiesel production, road de-­icing, enhanced geothermal system (EGS) recharge, underground reinjection, landfill disposal, ocean disposal, and evaporation pond disposal. Three saline aquifers from different regions of the US were selected as hypothetical GCS project sites to encompass variation in parameters that are relevant to the feasibility and economics of brine disposal. The three aquifers are the southern Mt. Simon Sandstone Formation in the Illinois Basin, IL; the Vedder Formation in the southern San Joaquin Basin, CA; and the Jasper Interval in the eastern Texas Gulf Basin, TX. These aquifers are candidates for GCS due to their physical characteristics and their close proximity to large CO2 emission sources. Feasibility and impacts were calculated using one mt-­CO2 injected as the functional unit of brine management. Scenarios were performed for typical 1000MW coal-­fired power plants (CFPP) that incurred an assumed 24 percent carbon capture energy penalty (EP), injected 90 percent of CO2 emissions (~9 million mt-­ CO2 injected annually), and treated extracted water onsite. Net present value (NPV), land requirements, laws and regulations, and technological limits were determined for each stage of disposal, and used to estimate feasibility. The boundary of the assessment began once extracted water was brought to the surface, and ended once the water evaporated, was injected underground, or was discharged into

  20. Zooplankton at deep Red Sea brine pools

    KAUST Repository

    Kaartvedt, Stein

    2016-03-02

    The deep-sea anoxic brines of the Red Sea comprise unique, complex and extreme habitats. These environments are too harsh for metazoans, while the brine–seawater interface harbors dense microbial populations. We investigated the adjacent pelagic fauna at two brine pools using net tows, video records from a remotely operated vehicle and submerged echosounders. Waters just above the brine pool of Atlantis II Deep (2000 m depth) appeared depleted of macrofauna. In contrast, the fauna appeared to be enriched at the Kebrit Deep brine–seawater interface (1466 m).

  1. Electron beam treatment of exhaust gas with high NOx concentration

    Science.gov (United States)

    Licki, Janusz; Chmielewski, Andrzej G.; Pawelec, Andrzej; Zimek, Zbigniew; Witman, Sylwia

    2014-05-01

    Simulated exhaust gases with a high NOx concentration, ranging from 200 to 1700 ppmv, were irradiated by an electron beam from an accelerator. In the first part of this study, only exhaust gases were treated. Low NOx removal efficiencies were obtained for high NOx concentrations, even with high irradiation doses applied. In the second part of study, gaseous ammonia or/and vapor ethanol were added to the exhaust gas before its inlet to the plasma reactor. These additions significantly enhanced the NOx removal efficiency. The synergistic effect of high SO2 concentration on NOx removal was observed. The combination of electron beam treatment with the introduction of the above additions and with the performance of irradiation under optimal parameters ensured high NOx removal efficiency without the application of a solid-state catalyst.

  2. [Reasons of high concentration ammonium in Yellow River, China].

    Science.gov (United States)

    Zhang, Xue-qing; Xia, Xing-hui; Yang, Zhi-feng

    2007-07-01

    Ammonium nitrogen contamination is one of the major problems of the Yellow River in China. The speciation, concentration and sources of nitrogen compounds as well as the water environment conditions of the Yellow River had been analyzed to study the reasons for the fact that the ammonium nitrogen concentration was above the water quality standard. In addition, laboratory experiments had been carried out to investigate the effects of suspended sediment (SS) on nitrification rate. The results indicated that the presence of SS could accelerate the nitrification process, therefore, the effects of SS on nitrification rate was not the reason for the high level of ammonium nitrogen in the river. The excessive and continuous input of nitrogen contaminants to the river was the fundamental reason for the high concentration of ammonium nitrogen. Organic and ammonium nitrogen with high concentration inhibitted the nitrification processes. When the initial NH4+ -N concentrations were 10.1, 18.4 and 28.2 mg/L, nitrification efficiencies were 17.4%, 13.0% and 2.5%, respectively. When the initial organic nitrogen concentrations were 5.5 and 8.6 mg/L, the maximum concentrations of ammonium nitrogen produced by the oxidation of organic nitrogen would reach 0.47 and 1.69 mg/L and they would last for 2 days and 6 days, respectively. The oxygen-consuming organics and toxic substance existing in the river water could inhibit the activity of nitrifying bacteria, and thus lead to the accumulation of ammonium nitrogen. In addition, the high pH value of river water resulted in the high concentration of nonionic ammonium nitrogen which would reduce the activity of nitrifying bacteria and decrease the nitrification rates. Besides, low river runoff, low SS content and low activity of nitrifying bacteria resulted in the high level of ammonium nitrogen of the river in the low water season.

  3. Differences in Swallowing between High and Low Concentration Taste Stimuli

    Directory of Open Access Journals (Sweden)

    Ahmed Nagy

    2014-01-01

    Full Text Available Taste is a property that is thought to potentially modulate swallowing behavior. Whether such effects depend on taste, intensity remains unclear. This study explored differences in the amplitudes of tongue-palate pressures in swallowing as a function of taste stimulus concentration. Tongue-palate pressures were collected in 80 healthy women, in two age groups (under 40, over 60, stratified by genetic taste status (nontasters, supertasters. Liquids with different taste qualities (sweet, sour, salty, and bitter were presented in high and low concentrations. General labeled magnitude scale ratings captured perceived taste intensity and liking/disliking of the test liquids. Path analysis explored whether factors of taste, concentration, age group, and/or genetic taste status impacted: (1 perceived intensity; (2 palatability; and (3 swallowing pressures. Higher ratings of perceived intensity were found in supertasters and with higher concentrations, which were more liked/disliked than lower concentrations. Sweet stimuli were more palatable than sour, salty, or bitter stimuli. Higher concentrations elicited stronger tongue-palate pressures independently and in association with intensity ratings. The perceived intensity of a taste stimulus varies as a function of stimulus concentration, taste quality, participant age, and genetic taste status and influences swallowing pressure amplitudes. High-concentration salty and sour stimuli elicit the greatest tongue-palate pressures.

  4. High Black Carbon (BC) Concentrations along Indian National Highways

    Science.gov (United States)

    Kumar, S.; Singh, A. K.; Singh, R. P.

    2015-12-01

    Abstract:Black carbon (BC), the optically absorbing component of carbonaceous aerosol, has direct influence on radiation budget and global warming. Vehicular pollution is one of the main sources for poor air quality and also atmospheric pollution. The number of diesel vehicles has increased on the Indian National Highways during day and night; these vehicles are used for the transport of goods from one city to another city and also used for public transport. A smoke plume from the vehicles is a common feature on the highways. We have made measurements of BC mass concentrations along the Indian National Highways using a potable Aethalometer installed in a moving car. We have carried out measurements along Varanasi to Kanpur (NH-2), Varanasi to Durgapur (NH-2), Varanasi to Singrauli (SH-5A) and Varanasi to Ghazipur (NH-29). We have found high concentration of BC along highways, the average BC mass concentrations vary in the range 20 - 40 µg/m3 and found high BC mass concentrations up to 600 μg/m3. Along the highways high BC concentrations were characteristics of the presence of industrial area, power plants, brick kilns and slow or standing vehicles. The effect of increasing BC concentrations along the National Highways and its impact on the vegetation and human health will be presented. Key Words: Black Carbon; Aethalometer; mass concentration; Indian National Highways.

  5. An improved brine shrimp larvae lethality microwell test method.

    Science.gov (United States)

    Zhang, Yi; Mu, Jun; Han, Jinyuan; Gu, Xiaojie

    2012-01-01

    This article described an improved brine shrimp larvae lethality microwell test method. A simply designed connecting vessel with alternative photoperiod was used to culture and collect high yield of active Artemia parthenogenetica nauplii for brine shrimp larvae lethality microwell test. Using this method, pure A. parthenogenetica nauplii suspension was easily cultured and harvested with high density about 100-150 larvae per milliliter and the natural mortality was reduced to near zero by elimination of unnecessary artificial disturbance. And its sensitivity was validated by determination of LC(50)-24 h of different reference toxicants including five antitumor agents, two pesticides, three organic pollutants, and four heavy metals salts, most of which exhibited LC(50)-24 h between 0.07 and 58.43 mg/L except for bleomycin and mitomycin C with LC(50)-24 h over 300 mg/L.

  6. Brine Dewatering Using Ultrasonic Nebulization Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Recovery of water from brine is critically important for manned space exploration. Resupply of water is prohibitively costly for extended missions. It is anticipated...

  7. Brine Dewatering Using Ultrasonic Nebulization Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Recovery of water from brine is critically important for future manned space exploration. Resupply of water is prohibitively costly for such extended missions. Water...

  8. Space and Industrial Brine Drying Technologies

    Science.gov (United States)

    Jones, Harry W.; Wisniewski, Richard S.; Flynn, Michael; Shaw, Hali

    2014-01-01

    This survey describes brine drying technologies that have been developed for use in space and industry. NASA has long considered developing a brine drying system for the International Space Station (ISS). Possible processes include conduction drying in many forms, spray drying, distillation, freezing and freeze drying, membrane filtration, and electrical processes. Commercial processes use similar technologies. Some proposed space systems combine several approaches. The current most promising candidates for use on the ISS use either conduction drying with membrane filtration or spray drying.

  9. Chemical aspects of a brine pool at the East Flower Garden bank, northwestern Gulf of Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Brooks, J.M.; Bright, T.J.; Bernard, B.B.; Schwab, C.R.

    1979-07-01

    A small pool on the flank of the East Flower Garden bank at a depth of 72 m in the Gulf of Mexico contains anoxic, hypersaline (approx. 200 g.kg/sup -1/) water. The flux of brine into and out of the pool contributes to erosional processes on the bank. The bulk ionic composition of the brine is similar to that of the Orca Basin brine, but differences between the two in gaseous hydrocarbon and carbon isotope content indicate different modes of origin. High levels of bacterial activity in the brine are indicated by ATP (> 80 ng.liter/sup -1/), hydrogen sulfide (> 2000 ..mu..mol.liter/sup -1/), isotopically light ..sigma..CO/sub 2/ (delta/sup 13/C =-23/sup 0///sub 00/ and the apparent generaton of elemental sulfur.

  10. Sterile Filtration of Highly Concentrated Protein Formulations: Impact of Protein Concentration, Formulation Composition, and Filter Material.

    Science.gov (United States)

    Allmendinger, Andrea; Mueller, Robert; Huwyler, Joerg; Mahler, Hanns-Christian; Fischer, Stefan

    2015-10-01

    Differences in filtration behavior of concentrated protein formulations were observed during aseptic drug product manufacturing of biologics dependent on formulation composition. The present study investigates filtration forces of monoclonal antibody formulations in a small-scale set-up using polyvinylidene difluoride (PVDF) or polyethersulfone (PES) filters. Different factors like formulation composition and protein concentration related to differences in viscosity, as well as different filtration rates were evaluated. The present study showed that filtration behavior was influenced by the presence or absence of a surfactant in the formulation, which defines the interaction between filter membrane and surface active formulation components. This can lead to a change in filter resistance (PES filter) independent on the buffer system used. Filtration behavior was additionally defined by rheological non-Newtonian flow behavior. The data showed that high shear rates resulting from small pore sizes and filtration pressure up to 1.0 bar led to shear-thinning behavior for highly concentrated protein formulations. Differences in non-Newtonian behavior were attributed to ionic strength related to differences in repulsive and attractive interactions. The present study showed that the interplay of formulation composition, filter material, and filtration rate can explain differences in filtration behavior/filtration flux observed for highly concentrated protein formulations thus guiding filter selection.

  11. Denitrification of fertilizer wastewater at high chloride concentration

    DEFF Research Database (Denmark)

    Ucisik, Ahmed Süheyl; Henze, Mogens

    g/l. The results of the experiments showed that biological denitrification was feasible at the extreme environmental conditions prevailing in fertilizer wastewater. Stable continuous biological denitrfication of the synthetic high chloride wastewater was performed up to 77.4 g Cl/l at 37 degree C......Wastewater from fertilizer industry is characterized by high contents of chloride concentration, which normally vary between 60 and 76 g/l. Experiments with bilogical denitrification were performed in lab-scale "fill and draw" reactors with synthetic wastewater with chloride concentrations up to 77.4...

  12. Study of thermal-gradient-induced migration of brine inclusions in salt. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Olander, D.R.

    1984-08-01

    Natural salt deposits, which are being considered for high-level waste disposal, contain a small volume fraction of water in the form of brine inclusions distributed throughout the salt. Radioactive decay heating of the nuclear wastes will impose a temperature gradient on the surrounding salt which mobilizes the brine inclusions. Inclusions filled completely with brine (the all-liquid inclusions) migrate up the temperature gradient and eventually accumulate brine near the buried waste forms. The brine may slowly corrode or degrade the waste forms, which is undesirable. Therefore it is important to consider the migration of brine inclusions in salt under imposed temperature gradients to properly evaluate the performance of a future salt repository for nuclear wastes. The migration velocities of the inclusions were found to be dependent on temperature, temperature gradient, and inclusion shape and size. The velocities were also dictated by the interfacial mass transfer resistance at brine/solid interface. This interfacial resistance depends on the dislocation density in the crystal, which in turn, depends on the axial compressive loading of the crystal. At low axial loads, the dependence between the velocity and temperature gradient is nonlinear. At high axial loads, the interfacial resistance is reduced and the migration velocity depends linearly on the temperature gradient. All-liquid inclusions filled with mixed brines were also studied. For gas-liquid inclusions, helium, air and argon were compared. Migration studies were also conducted on single crystallites of natural salt as well as in polycrystalline natural salt samples. The behavior of the inclusions at large-ange grain boundaries was observed.

  13. Rapid and controlled transformation of nitrate in water and brine by stabilized iron nanoparticles

    Science.gov (United States)

    Xiong, Zhong; Zhao, Dongye; Pan, Gang

    2009-05-01

    Highly reactive zero-valent iron (ZVI) nanoparticles stabilized with carboxymethyl cellulose (CMC) were tested for reduction of nitrate in fresh water and brine. Batch kinetic tests showed that the pseudo first-order rate constant ( k obs) with the stabilized nanoparticles was five times greater than that for non-stabilized counterparts. The stabilizer not only increased the specific surface area of the nanoparticles, but also increased the reactive particle surface. The allocation between the two reduction products, NH4 + and N2, can be manipulated by varying the ZVI-to-nitrate molar ratio and/or applying a Cu-Pd bimetallic catalyst. Greater CMC-to-ZVI ratios lead to faster nitrate reduction. Application of a 0.05 M HEPES buffer increased the k obs value by 15 times compared to that without pH control. Although the presence of 6% NaCl decreased k obs by 30%, 100% nitrate was transformed within 2 h in the saline water. The technology provides a powerful alternative for treating water with concentrated nitrate such as ion exchange brine.

  14. Aromatic hydrocarbons associated with brines from geopressured wells. Annual report, [December 28, 1990--December 16, 1991

    Energy Technology Data Exchange (ETDEWEB)

    1992-09-01

    The various operational wells were sampled on a monthly basis for the yield of the cryocondensate hydrocarbons. The total cryocondensate concentration as well as the concentrations in the brine and the gas after passing the separator system are summarized. The total cryocondensate yield is displayed.

  15. High estrogen concentrations in receiving river discharge from a concentrated livestock feedlot.

    Science.gov (United States)

    Chen, Te-San; Chen, Ting-Chien; Yeh, Kuei-Jyum C; Chao, How-Ran; Liaw, Ean-Tun; Hsieh, Chi-Ying; Chen, Kuan-Chung; Hsieh, Lien-Te; Yeh, Yi-Lung

    2010-07-15

    Environmental estrogenic chemicals interrupt endocrine systems and generate reproductive abnormalities in wildlife, especially natural and synthetic estrogenic steroid hormones such as 17beta-estradiol (E2), estrone (E1), estriol (E3), 17alpha-ethynylestradiol (EE2), and diethylstilbestrol (DES). Concentrated animal feedlot operations (CAFOs) are of particular concern since large amounts of naturally excreted estrogens are discharged into aquatic environments. This study investigated E2, E1, E3, EE2, and DES with high performance liquid chromatography/tandem mass (HPLC-MS/MS) analyses along Wulo Creek in southern Taiwan, near a concentrated livestock feedlot containing 1,030,000 broiler chickens, 934,000 laying hens, 85,000 pigs, and 1500 cattle. Sampling was performed from December 2008 to May 2009, in which 54 samples were collected. Experimental results indicate that concentrations of EE2 were lower than the limit of detection (LOD), and concentrations of DES were only detected twice. Concentrations ranged from 7.4 to 1267 ng/L for E1, from not detected (ND) to 313.6 ng/L for E2, and from ND to 210 ng/L for E3. E1 had the highest average mass fraction (72.2 + or - 3.6%), which was significantly higher than E3 (16.2 + or - 1.7%) and E2 (11.5 + or - 2.6%). Additionally, the mean E2 equivalent quotient (EEQ) ranged from 17.3 to 137.9 ng-E2/L. Despite having a markedly lower concentration than E1, E2 more significantly contributed (52.4 + or - 6.0%) EEQ than E1 (19.7 + or - 3.5%). Moreover, the concentrations of E2, E1, and E3 upstream were significantly higher than concentrations downstream, suggesting a high attenuation effect and fast degradation in the study water. Most concentrations in winter season were higher than those of spring season due to the low dilution effect and low microbial activity in the winter season. Based on the results of this study, we recommend further treatment of the wastewater discharge from the feedlot.

  16. Biodegradation dynamics of high catechol concentrations by Aspergillus awamori.

    Science.gov (United States)

    Stanchev, Veselin; Stoilova, Ivanka; Krastanov, Albert

    2008-06-15

    The biodegradation process of high catechol concentrations by Aspergillus awamori was investigated. The values of the kinetic constants for a model of specific growth rate at different initial conditions were determined. At 1.0 g/L catechol concentration, the biodegradation process proceeded in the conditions of substrate limitation. At higher catechol concentrations (2.0 and 3.0 g/L) a presence of substrate inhibition was established. The dynamics of the specific catechol degradation rate was studied and the values of catechol and biomass concentrations, maximizing the specific catechol degradation rate, were estimated analytically. The specified ratio catechol/biomass could serve as a starting base for determination of the initial conditions for a batch process, for specifying the moment of feeding for a fed-batch process, and for monitoring and control of a continuous process by the aim of time-optimal control.

  17. Effective Wettability Measurements of CO2-Brine-Sandstone System at Different Reservoir Conditions

    Science.gov (United States)

    Al-Menhali, Ali; Krevor, Samuel

    2014-05-01

    , core-scale effective contact angle can be determined. In addition to providing a quantitative measure of the core-averaged wetting properties, the technique allows for the observation of shifts in contact angle with changing conditions. We examine the wettability changes of the CO2-brine system in Berea sandstone with variations in reservoir conditions including supercritical, gaseous and liquid CO2injection. We evaluate wettability variation within a single rock with temperature, pressure, and salinity across a range of conditions relevant to subsurface CO2 storage. This study will include results of measurements in a Berea sandstone sample across a wide range of conditions representative of subsurface reservoirs suitable for CO2 storage (5-20 MPa, 25-90 oC, 0-5 mol kg-1). The measurement uses X-ray CT imaging in a state of the art core flooding laboratory designed to operate at high temperature, pressure, and concentrated brines.

  18. High shear treatment of concentrates and drying conditions influence the solubility of milk protein concentrate powders.

    Science.gov (United States)

    Augustin, Mary Ann; Sanguansri, Peerasak; Williams, Roderick; Andrews, Helen

    2012-11-01

    The solubility of milk protein concentrate (MPC) powders was influenced by the method used for preparing the concentrate, drying conditions, and the type of dryer used. Increasing total solids of the ultrafiltered concentrates (23% total solids, TS) by diafiltration to 25% TS or evaporation to 31% TS decreased the solubility of MPC powders (80-83% protein, w/w dry basis), with ultrafiltration followed by evaporation to higher total solids having the greater detrimental effect on solubility. High shear treatment (homogenisation at 350/100 bar, microfluidisation at 800 bar or ultrasonication at 24 kHz, 600 watts) of ultrafiltered and diafiltered milk protein concentrates prior to spray drying increased the nitrogen solubility of MPC powders (82% protein, w/w dry basis). Of the treatments applied, microfluidisation was the most effective for increasing nitrogen solubility of MPC powders after manufacture and during storage. Manufacture of MPC powders (91% protein, w/w dry basis) prepared on two different pilot-scale dryers (single stage or two stage) from milk protein concentrates (20% TS) resulted in powders with different nitrogen solubility and an altered response to the effects of microfluidisation. Microfluidisation (400, 800 and 1200 bar) of the concentrate prior to drying resulted in increased long term solubility of MPC powders that were prepared on a single stage dryer but not those produced on a two stage spray dryer. This work demonstrates that microfluidisation can be used as a physical intervention for improving MPC powder solubility. Interactions between the method of preparation and treatment of concentrate prior to drying, the drying conditions and dryer type all influence MPC solubility characteristics.

  19. Flow behaviour of supercritical CO2 and brine in Berea sandstone during drainage and imbibition revealed by medical X-ray CT images

    Science.gov (United States)

    Zhang, Yi; Nishizawa, Osamu; Kiyama, Tamotsu; Chiyonobu, Shun; Xue, Ziqiu

    2014-06-01

    imbibition, changes reflecting the interfingering pattern across the replacement fronts. Although the permeability differences between high- and low-porosity layers were not sufficiently large to disturb the uniform flow of brine, the CO2 concentration in the high-porosity layers may have been caused by the differences of capillary pressure between wide and narrow pore throats, perhaps enhanced by an invasion percolation mechanism in flow-path networks.

  20. Technique for Separating Magnesium and Lithium from Salt Lake Brine with High Mg/Li Ratio%高镁锂比盐湖卤水镁锂分离工艺

    Institute of Scientific and Technical Information of China (English)

    张丽芬; 张大义; 欧阳红勇; 汪全义; 宁顺明; 万洪强

    2016-01-01

    以酸化提硼后卤水为原料,采用饱和氯化钾溶液作为沉镁剂,使用三步结晶法进行了沉淀镁并富集锂的研究。结果表明,通过3段蒸发结晶析出光卤石,可以有效地实现镁锂分离:添加95%理论用量的氯化钾可以把原卤水中的镁锂质量比由10.1∶1降低到0.39∶1,锂在滤液中总回收率为77.90%,并使锂浓度从10 g/L富集到49.30 g/L。%With the salt lake brine after boron recovery as raw material and saturated solution of potassium chloride for magnesium precipitation, research was carried out on separating lithium from magnesium by the process of three⁃step evaporation crystallization. The experimental results show that the separation between lithium and magnesium could be attained after carnallite precipitation through three⁃step evaporation crystallization. The mass ratio of magnesium to lithium was reduced from 10.1∶1 to 0.39∶1 with the addition of potassium chloride at 95% of theoretical amount, resulting in the total Li+ recovery from the filtrate reaching 77.90%, and Li+ concentration enriched from 10 g/L to 49.30 g/L.

  1. High-concentration planar microtracking photovoltaic system exceeding 30% efficiency

    Science.gov (United States)

    Price, Jared S.; Grede, Alex J.; Wang, Baomin; Lipski, Michael V.; Fisher, Brent; Lee, Kyu-Tae; He, Junwen; Brulo, Gregory S.; Ma, Xiaokun; Burroughs, Scott; Rahn, Christopher D.; Nuzzo, Ralph G.; Rogers, John A.; Giebink, Noel C.

    2017-08-01

    Prospects for concentrating photovoltaic (CPV) power are growing as the market increasingly values high power conversion efficiency to leverage now-dominant balance of system and soft costs. This trend is particularly acute for rooftop photovoltaic power, where delivering the high efficiency of traditional CPV in the form factor of a standard rooftop photovoltaic panel could be transformative. Here, we demonstrate a fully automated planar microtracking CPV system solar cell at >660× concentration ratio over a 140∘ full field of view. In outdoor testing over the course of two sunny days, the system operates automatically from sunrise to sunset, outperforming a 17%-efficient commercial silicon solar cell by generating >50% more energy per unit area per day in a direct head-to-head competition. These results support the technical feasibility of planar microtracking CPV to deliver a step change in the efficiency of rooftop solar panels at a commercially relevant concentration ratio.

  2. Microbial Diversity and Ecology in the Interfaces of the Deep-sea Anoxic Brine Pools in the Red Sea

    KAUST Repository

    Hikmawan, Tyas I.

    2015-05-01

    Deep-sea anoxic brine pools are one of the most extreme ecosystems on Earth, which are characterized by drastic changes in salinity, temperature, and oxygen concentration. The interface between the brine and overlaying seawater represents a boundary of oxic-anoxic layer and a steep gradient of redox potential that would initiate favorable conditions for divergent metabolic activities, mainly methanogenesis and sulfate reduction. This study aimed to investigate the diversity of Bacteria, particularly sulfate-reducing communities, and their ecological roles in the interfaces of five geochemically distinct brine pools in the Red Sea. Performing a comprehensive study would enable us to understand the significant role of the microbial groups in local geochemical cycles. Therefore, we combined culture-dependent approach and molecular methods, such as 454 pyrosequencing of 16S rRNA gene, phylogenetic analysis of functional marker gene encoding for the alpha subunits of dissimilatory sulfite reductase (dsrA), and single-cell genomic analysis to address these issues. Community analysis based on 16S rRNA gene sequences demonstrated high bacterial diversity and domination of Bacteria over Archaea in most locations. In the hot and multilayered Atlantis II Deep, the bacterial communities were stratified and hardly overlapped. Meanwhile in the colder brine pools, sulfatereducing Deltaproteobacteria were the most prominent bacterial groups inhabiting the interfaces. Corresponding to the bacterial community profile, the analysis of dsrA gene sequences revealed collectively high diversity of sulfate-reducing communities. Desulfatiglans-like dsrA was the prevalent group and conserved across the Red Sea brine pools. In addition to the molecular studies, more than thirty bacterial strains were successfully isolated and remarkably were found to be cytotoxic against the cancer cell lines. However, none of them were sulfate reducers. Thus, a single-cell genomic analysis was used to study

  3. Beryllium-10 concentrations in water samples of high northern latitudes

    Energy Technology Data Exchange (ETDEWEB)

    Strobl, C.; Eisenhauer, A.; Schulz, V.; Baumann, S.; Mangini, A. [Heidelberger Akademie der Wissenschaften, Heildelberg (Germany); Kubik, P.W. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1997-09-01

    {sup 10}Be concentrations in the water column of high northern latitudes were not available so far. We present different {sup 10}Be profiles from the Norwegian-Greenland Sea, the Arctic Ocean, and the Laptev Sea. (author) 3 fig., 3 refs.

  4. Optimization of Scatterer Concentration in High-Gain Scattering Media

    Institute of Scientific and Technical Information of China (English)

    ZHU Jiu-Gao; ZHU He-Yuan; SUN Die-Chi; DU Ge-Guo; LI Fu-Ming

    2001-01-01

    We report the scatterer concentration-dependent behaviour of laser action in high-gain scattering media. Amodified model of a random laser is proposed to explain the experimental results in good agreement. We mayuse this modified model to design and optimize the random laser system. A further detailed model is needed toquantitatively analyse the far-field distribution of random laser action.

  5. Organic geochemistry and brine composition in Great Salt, Mono, and Walker Lakes

    Science.gov (United States)

    Domagalski, Joseph L.; Orem, William H.; Eugster, Hans P.

    1989-11-01

    Samples of Recent sediments, representing up to 1000 years of accumulation, were collected from three closed basin lakes (Mono Lake, CA, Walker Lake, NV, and Great Salt Lake, UT) to assess the effects of brine composition on the accumulation of total organic carbon, the concentration of dissolved organic carbon, humic acid structure and diagenesis, and trace metal complexation. The Great Salt Lake water column is a stratified Na-Mg-Cl-SO 4 brine with low alkalinity. Algal debris is entrained in the high density (1.132-1.190 g/cc) bottom brines, and in this region maximum organic matter decomposition occurs by anaerobic processes, with sulfate ion as the terminal electron acceptor. Organic matter, below 5 cm of the sediment-water interface, degrades at a very slow rate in spite of very high pore-fluid sulfate levels. The organic carbon concentration stabilizes at 1.1 wt%. Mono Lake is an alkaline (Na-CO 3-Cl-SO 4) system. The water column is stratified, but the bottom brines are of lower density relative to the Great Salt Lake, and sedimentation of algal debris is rapid. Depletion of pore-fluid sulfate, near l m of core, results in a much higher accumulation of organic carbon, approximately 6 wt%. Walker Lake is also an alkaline system. The water column is not stratified, and decomposition of organic matter occurs by aerobic processes at the sediment-water interface and by anaerobic processes below. Total organic carbon and dissolved organic carbon concentrations in Walker Lake sediments vary with location and depth due to changes in input and pore-fluid sulfate concentrations. Nuclear magnetic resonance studies ( 13C) of humic substances and dissolved organic carbon provide information on the source of the Recent sedimentary organic carbon (aquatic vs. terrestrial), its relative state of decomposition, and its chemical structure. The spectra suggest an algal origin with little terrestrial signature at all three lakes. This is indicated by the ratio of aliphatic to

  6. [Toxic effects of high concentrations of ammonia on Euglena gracilis].

    Science.gov (United States)

    Liu, Yan; Shi, Xiao-Rong; Cui, Yi-Bin; Li, Mei

    2013-11-01

    Ammonia is among the common contaminants in aquatic environments. The present study aimed at evaluation of the toxicity of ammonia at high concentration by detecting its effects on the growth, pigment contents, antioxidant enzyme activities, and DNA damage (comet assay) of a unicellular microalga, Euglena gracilis. Ammonia restrained the growth of E. gracilis, while at higher concentrations, ammonia showed notable inhibition effect, the growth at 2 000 mg x L(-1) was restrained to 55.7% compared with that of the control; The contents of photosynthetic pigments and protein went up with increasing ammonia dosage and decreased when the ammonia concentration was above 1000 mg x L(-1); In addition, there was an obvious increase in SOD and POD activities, at higher concentration (2 000 mg x L(-1)), activities of SOD and POD increased by 30.7% and 49.4% compared with those of the control, indicating that ammonia could promote activities of antioxidant enzymes in E. gracilis; The degree of DNA damage observed in the comet assay increased with increasing ammonia concentration, which suggested that high dose of ammonia may have potential mutagenicity on E. gracilis.

  7. Using 81Kr and noble gases to characterize and date groundwater and brines in the Baltic Artesian Basin on the one-million-year timescale

    Science.gov (United States)

    Gerber, Christoph; Vaikmäe, Rein; Aeschbach, Werner; Babre, Alise; Jiang, Wei; Leuenberger, Markus; Lu, Zheng-Tian; Mokrik, Robert; Müller, Peter; Raidla, Valle; Saks, Tomas; Waber, H. Niklaus; Weissbach, Therese; Zappala, Jake C.; Purtschert, Roland

    2017-05-01

    Analyses for 81Kr and noble gases on groundwater from the deepest aquifer system of the Baltic Artesian Basin (BAB) were performed to determine groundwater ages and uncover the flow dynamics of the system on a timescale of several hundred thousand years. We find that the system is controlled by mixing of three distinct water masses: Interglacial or recent meteoric water (δ18O ≈ -10.4‰) with a poorly evolved chemical and noble gas signature, glacial meltwater (δ18O ⩽ -18‰) with elevated noble gas concentrations, and an old, high-salinity brine component (δ18O ⩾ -4.5‰, ⩾ 90 g Cl-/L) with strongly depleted atmospheric noble gas concentrations. The 81Kr measurements are interpreted within this mixing framework to estimate the age of the end-members. Deconvoluted 81Kr ages range from 300 ka to 1.3 Ma for interglacial or recent meteoric water and glacial meltwater. For the brine component, ages exceed the dating range of the ATTA-3 instrument of 1.3 Ma. The radiogenic noble gas components 4He∗ and 40Ar∗ are less conclusive but also support an age of > 1 Ma for the brine. Based on the chemical and noble gas concentrations and the dating results, we conclude that the brine originates from evaporated seawater that has been modified by later water-rock interaction. As the obtained tracer ages cover several glacial cycles, we discuss the impact of the glacial cycles on flow patterns in the studied aquifer system.

  8. High-efficiency organic solar concentrators for photovoltaics.

    Science.gov (United States)

    Currie, Michael J; Mapel, Jonathan K; Heidel, Timothy D; Goffri, Shalom; Baldo, Marc A

    2008-07-11

    The cost of photovoltaic power can be reduced with organic solar concentrators. These are planar waveguides with a thin-film organic coating on the face and inorganic solar cells attached to the edges. Light is absorbed by the coating and reemitted into waveguide modes for collection by the solar cells. We report single- and tandem-waveguide organic solar concentrators with quantum efficiencies exceeding 50% and projected power conversion efficiencies as high as 6.8%. The exploitation of near-field energy transfer, solid-state solvation, and phosphorescence enables 10-fold increases in the power obtained from photovoltaic cells, without the need for solar tracking.

  9. Bioleaching of marmatite in high concentration of iron

    Institute of Scientific and Technical Information of China (English)

    邱冠周; 吴伯增; 覃文庆; 蓝卓越

    2002-01-01

    Bioleaching of marmatite with a culture of Thiobacillus ferrooxidans and Thiobacillus thiooxidans in high concentration of iron was studied, the results show that the zinc leaching rate of the mixed culture is faster than that of the sole Thiobacillus ferrooxidans, the increasing iron concentration in leaching solution enhances the zinc leaching rate. The SEM analysis indicates that the chemical leaching residues is covered with porous solid layer of elemental sulfur, while elemental sulfur is not found in the bacterial leaching residues. The primary role of bacteria in bioleaching of sphalerite is to oxidize the chemical leaching products of ferrous ion and elemental sulfur, thus the indirect mechanism prevails in the bioleaching of marmatite.

  10. High concentration of calcium ions in Golgi apparatus

    Institute of Scientific and Technical Information of China (English)

    XUESHAOBAI; M.ROBERTNICOUD; 等

    1994-01-01

    The interphase NIH3T3 cells were vitally fluorescentstained with calcium indicator fluo-3 and Glogi probe C6-NBD-ceramide,and then the single cells were examined by laser scanning confocal microscopy(LSCFM) for subcellular distributions of Ca2+ and the location of Golgi apparatus.In these cells,the intracellular Ca2+ were found to be highly concentrated in the Golgi apparatus.The changes of distribution of cytosolic high Ca2+ region and the Golgi apparatus coincided with the cell cycle phase.In calcium free medium,when the plasma membrane of the cells which had been loaded with fluo-3/AM were permeated by digitonin,the fluorescence of the Golgi region decreased far less than that of the cytosol.Our results indicated that the Glogi lumen retained significantly high concentration of free calcium.

  11. Review of silicon solar cells for high concentrations

    Science.gov (United States)

    Schwartz, R. J.

    1982-06-01

    The factors that limit the performance of high concentration silicon solar cells are reviewed. The design of a conventional high concentration cell is discussed, together with the present state of the art. Unconventional cell designs that have been proposed to overcome the limitations of the conventional design are reviewed and compared. The current status of unconventional cells is reviewed. Among the unconventional cells discussed are the interdigitated back-contact cell, the double-sided cell, the polka dot cell, and the V-groove cell. It is noted that all the designs for unconventional cells require long diffusion lengths for high efficiency operation, even though the demands in this respect are less for those cells with the optical path longer than the diffusion path.

  12. Experimental biological effects assessment associated with on-shore brine discharge from the creation of gas storage caverns

    Science.gov (United States)

    Quintino, Victor; Rodrigues, Ana Maria; Freitas, Rosa; Ré, Ana

    2008-09-01

    Most of the studies on biological and ecological effects associated with brine discharge into the marine environment are related to the operation of desalination plants, for the production of freshwater. In this study we analysed the biological effects of a brine effluent from a completely different source, produced from the lixiviation of rock salt caves, for the creation of natural gas storage caverns. Lethal and sub-lethal endpoints following exposure to the brine were studied in a range of macrofauna species characteristic of the soft and hard bottom habitats in the vicinity of the discharge area, namely the isopod Eurydice pulchra, the annelids Sabellaria alveolata and Ophelia radiata, the sea-urchin Paracentrotus lividus and the bivalve Mytilus galloprovincialis. In a first series of experiments, brine, with salinity above 300, was diluted in distilled water to a salinity value close to that of the seawater in the discharge area (salinity 36) and, surprisingly, none of the exposed species was able to survive or develop into viable larvae. A second series of experiments exposed the species to brine diluted with seawater, simulating more realistic discharge circumstances. All the tested species at all the measured endpoints (adult survival, larval abnormal development, sperm fertilization success) showed negative biological effects in brine solutes always at a lower salinity than that of a salinity control obtained with concentrated seawater. The sub-lethal experiments with larval development of P. lividus, S. alveolata and M. galloprovincialis, and the fertilization success of P. lividus gave EC 50 values for the brine solute with salinity in the range of 40.9-43.5, whereas the EC 50 values for the concentrated seawater were in the range of salinity 44.2-49.0. It is hypothesised that differences in the ionic composition of the brine cause the inability of the species to tolerate the exposure to brine.

  13. Meltability and Stretchability of White Brined Cheese: Effect of Emulsifier Salts

    Directory of Open Access Journals (Sweden)

    Khaled Abu-Alruz

    2009-01-01

    Full Text Available Problem statement: This study was based on the hypothesis that by adding low concentrations of emulsifier salts, may specifically act on the cross linking bonds of the protein matrix, to the original brine (storage medium it would be possible to induce meltability and stretchability in white brined cheese. Approach: A new apparatus for measuring the actual stretchability was designed and constructed; measurements on different cheese samples proved its validity and reliability to measure stretchability. The apparatus was used to evaluate the effect of five types of emulsifier salts under different processing conditions. Results: It was found that by adding 0.2% (w/w Puromelt C1 or Monosodium phosphate to the brine of white brined cheese, higher levels of stretchability and meltability were induced after 2-4 weeks of storage. Conclusion: Addition of emulsifying salts was proved to be effective method in inducing meltability and stretchability of white brined cheese. Type of salt, its concentration, type of cheese and soaking time are factors that should be controlled to attain the optimum results.

  14. Decomposition of high concentration SF6 using an electron beam

    Science.gov (United States)

    Son, Youn-Suk; Lee, Sung-Joo; Choi, Chang Yong; Park, Jun-Hyeong; Kim, Tak-Hyun; Jung, In-Ha

    2016-07-01

    In this study, high concentration SF6 (2-10%) was decomposed using an electron beam irradiation. Various influential factors were investigated to improve the destruction and removal efficiency (DRE) of SF6. The initial concentrations of SF6, absorbed doses, SF6/H2 ratios and retention times were the main factors of concern. As a result, the DRE increased as the adsorbed dose and retention time increased. The DRE of SF6 also increased up to 20% approximately when H2 was added to the reaction mixture. On the other hand, the DRE of SF6 decreased as initial concentrations of SF6 increased. Finally, the main by-product formed from SF6 decomposition by the electron beam was HF.

  15. An evaporated seawater origin for the ore-forming brines in unconformity-related uranium deposits (Athabasca Basin, Canada): Cl/Br and δ 37Cl analysis of fluid inclusions

    Science.gov (United States)

    Richard, Antonin; Banks, David A.; Mercadier, Julien; Boiron, Marie-Christine; Cuney, Michel; Cathelineau, Michel

    2011-05-01

    Analyses of halogen concentration and stable chlorine isotope composition of fluid inclusions from hydrothermal quartz and carbonate veins spatially and temporally associated with giant unconformity-related uranium deposits from the Paleoproterozoic Athabasca Basin (Canada) were performed in order to determine the origin of chloride in the ore-forming brines. Microthermometric analyses show that samples contain variable amounts of a NaCl-rich brine (Cl concentration between 120,000 and 180,000 ppm) and a CaCl 2-rich brine (Cl concentration between 160,000 and 220,000 ppm). Molar Cl/Br ratios of fluid inclusion leachates range from ˜100 to ˜900, with most values between 150 and 350. Cl/Br ratios below 650 (seawater value) indicate that the high salinities were acquired by evaporation of seawater. Most δ 37Cl values are between -0.6‰ and 0‰ (seawater value) which is also compatible with a common evaporated seawater origin for both NaCl- and CaCl 2-rich brines. Slight discrepancies between the Cl concentration, Cl/Br, δ 37Cl data and seawater evaporation trends, indicate that the evaporated seawater underwent secondary minor modification of its composition by: (i) mixing with a minor amount of halite-dissolution brine or re-equilibration with halite during burial; (ii) dilution in a maximum of 30% of connate and/or formation waters during its migration towards the base of the Athabasca sandstones; (iii) leaching of chloride from biotites within basement rocks and (iv) water loss by hydration reactions in alteration haloes linked to uranium deposition. The chloride in uranium ore-forming brines of the Athabasca Basin has an unambiguous dominantly marine origin and has required large-scale seawater evaporation and evaporite deposition. Although the direct evidence for evaporative environments in the Athabasca Basin are lacking due to the erosion of ˜80% of the sedimentary pile, Cl/Br ratios and δ 37Cl values of brines have behaved conservatively at the basin

  16. Life at high salt concentrations, intracellular KCl concentrations, and acidic proteomes

    Directory of Open Access Journals (Sweden)

    Aharon eOren

    2013-11-01

    Full Text Available Extremely halophilic microorganisms that accumulate KCl for osmotic balance (the Halobacteriaceae, Salinibacter have a large excess of acidic amino acids in their proteins. This minireview explores the occurrence of acidic proteomes in halophiles of different physiology and phylogenetic affiliation. For fermentative bacteria of the order Halanaerobiales, known to accumulate KCl, an acidic proteome was predicted. However, this is not confirmed by genome analysis. The reported excess of acidic amino acids is due to a high content of Gln and Asn, which yield Glu and Asp upon acid hydrolysis. The closely related Halorhodospira halophila and Halorhodospira halochloris use different strategies to cope with high salt. The first has an acidic proteome and accumulates high KCl concentrations at high salt concentrations; the second does not accumulate KCl and lacks an acidic proteome. Acidic proteomes can be predicted from the genomes of some moderately halophilic aerobes that accumulate organic osmotic solutes (Halomonas elongata, Chromohalobacter salexigens and some marine bacteria. Based on the information on cultured species it is possible to understand the pI profiles predicted from metagenomic data from hypersaline environments.

  17. Strontium isotope systematics of mixing groundwater and oil-field brine at Goose Lake in northeastern Montana, USA

    Science.gov (United States)

    Peterman, Zell E.; Thamke, Joanna N.; Futa, Kiyoto; Preston, Todd

    2012-01-01

    Groundwater, surface water, and soil in the Goose Lake oil field in northeastern Montana have been affected by Cl−-rich oil-field brines during long-term petroleum production. Ongoing multidisciplinary geochemical and geophysical studies have identified the degree and local extent of interaction between brine and groundwater. Fourteen samples representing groundwater, surface water, and brine were collected for Sr isotope analyses to evaluate the usefulness of 87Sr/86Sr in detecting small amounts of brine. Differences in Sr concentrations and 87Sr/86Sr are optimal at this site for the experiment. Strontium concentrations range from 0.13 to 36.9 mg/L, and corresponding 87Sr/86Sr values range from 0.71097 to 0.70828. The local brine has 168 mg/L Sr and a 87Sr/86Sr value of 0.70802. Mixing relationships are evident in the data set and illustrate the sensitivity of Sr in detecting small amounts of brine in groundwater. The location of data points on a Sr isotope-concentration plot is readily explained by an evaporation-mixing model. The model is supported by the variation in concentrations of most of the other solutes.

  18. Impact of pressure and temperature on CO2-brine-mica contact angles and CO2-brine interfacial tension: Implications for carbon geo-sequestration.

    Science.gov (United States)

    Arif, Muhammad; Al-Yaseri, Ahmed Z; Barifcani, Ahmed; Lebedev, Maxim; Iglauer, Stefan

    2016-01-15

    Precise characterization of wettability of CO2-brine-rock system and CO2-brine interfacial tension at reservoir conditions is essential as they influence capillary sealing efficiency of caprocks, which in turn, impacts the structural and residual trapping during CO2 geo-sequestration. In this context, we have experimentally measured advancing and receding contact angles for brine-CO2-mica system (surface roughness ∼12nm) at different pressures (0.1MPa, 5MPa, 7MPa, 10MPa, 15MPa, 20MPa), temperatures (308K, 323K, and 343K), and salinities (0wt%, 5wt%, 10wt%, 20wt% and 30wt% NaCl). For the same experimental matrix, CO2-brine interfacial tensions have also been measured using the pendant drop technique. The results indicate that both advancing and receding contact angles increase with pressure and salinity, but decrease with temperature. On the contrary, CO2-brine interfacial tension decrease with pressure and increase with temperature. At 20MPa and 308K, the advancing angle is measured to be ∼110°, indicating CO2-wetting. The results have been compared with various published literature data and probable factors responsible for deviations have been highlighted. Finally we demonstrate the implications of measured data by evaluating CO2 storage heights under various operating conditions. We conclude that for a given storage depth, reservoirs with lower pressures and high temperatures can store larger volumes and thus exhibit better sealing efficiency.

  19. MR imaging of heterogeneity in partially frozen brine and their effect on ultrasonic wave propagation

    Science.gov (United States)

    Pradhan, O.; Matsushima, J.; Suzuki, M.

    2012-12-01

    Methane hydrate bearing sediment possesses unique seismic wave propagation properties. Both high seismic wave velocity and high wave attenuation are observed in methane hydrate bearing sediment. We used brine with salinity 2% in analogous to methane hydrate for conducting laboratory waveform measurement and characterization by using nuclear magnetic resonance (NMR) and magnetic resonance imaging (MRI) technique. When brine undergoes freezing, only pure water freezes into ice and salt remains in solution with successively increasing salinity and decreasing freezing point of the solution. Unfrozen brine is enclosed inside micro pores in ice, with exhibiting solid-liquid coexisting system. We used conventional pulse transmission technique to measure compressional wave velocity in partially frozen brine when brine is subjected cooling down to -12oC. Waveform measurement shows sudden increase in compressional wave velocity at temperature -3oC. Below -3oC, velocity increases slightly. Largest wave attenuation is observed at around -3oC. We conducted MRI experiment by using instrument Varian Unity Inova 4.7T. T1 weighted and diffusion weighted (DW) MR images were prepared by applying magnetic field gradient of 0.3 gauss/cm. We observe the spatial distribution of pores, microstructures and heterogeneity in partially frozen brine sample slices. Two dimensional apparent diffusion coefficient (ADC) maps are prepared from DW images with b-values 0 and 81 s/mm2 respectively. We estimate porosity quantitatively from each MR slices at temperature -3, -5, -7 and -12oC by using image analysis technique. Gassmann equation is applied to calculate compressional wave velocity from the porosity data and compared with the measured velocity obtained by waveform analysis technique. The NMR results show the existence of high and low mobility unfrozen brine in the pore space. MR imaging shows the heterogeneously distributed porosity values within a single slice with low porosity and high

  20. Modeling brine and nutrient dynamics in Antarctic sea ice: the case of dissolved silica

    Science.gov (United States)

    Vancoppenolle, M.; Goosse, H.; de Montety, A.; Fichefet, T.; Tremblay, B.; Tison, J.

    2009-12-01

    Sea ice ecosystems are characterized by micro-algae living in brine inclusions. The growth rate of ice algae depends on light and nutrient supply. Here, the interactions between nutrients and brine dynamics under the influence of algae are investigated using a one-dimensional model. The model includes snow and ice thermodynamics with brine physics and an idealized sea ice biological component, characterized by one nutrient, namely dissolved silica (DSi). In the model, DSi follows brine motion and is consumed by ice algae. Depending on physical ice characteristics, the brine flow is either advective, diffusive or turbulent. The vertical profiles of ice salinity and DSi concentration are solutions of advection-diffusion equations. The model is configured to simulate the typical thermodynamic regimes of first-year Antarctic pack ice. The simulated vertical profiles of salinity and DSi qualitatively reproduce observations. Analysis of results highlights the role of convection in the lowermost 5-10 cm of ice. Convection mixes saline, nutrient-poor brine with comparatively fresh, nutrient-rich seawater. This implies a rejection of salt to the ocean and a flux of DSi to the ice. In presence of growing algae, the simulated ocean-to-ice DSi flux increases by 0-115% compared to an abiotic situation. In turn, primary production and brine convection act in synergy to form a nutrient pump. The other important processes are the flooding of the surface by seawater and the percolation of meltwater. The former refills nutrients near the ice surface in spring. The latter, if present, tends to expell nutrients from the ice in summer. Sketch of salt (left) and nutrient (right) exchanges at the ice-ocean interface proposed in this paper.

  1. Valorisation of Ca and Mg by-products from mining and seawater desalination brines for water treatment applications

    OpenAIRE

    Casas Garriga, Sandra; Aladjem, Carlos; Larrotcha, Enric; Gibert Agulló, Oriol; Valderrama Angel, César Alberto; Cortina Pallás, José Luís

    2014-01-01

    BACKGROUNDBrines from the drainage of potash mine tailings and from seawater reverse osmosis (SWRO) desalination were previously evaluated as sources of NaCl for the chlor-alkali industry. Valorisation of NaCl as raw material is required to meet the membrane electrolysis specifications of NaCl saturation and control of interferences (Ca, Mg and sulphate). Brines concentration in NaCl was previously achieved for SWRO brines using electrodialysis (ED). In this work, valorisation of Ca and Mg by...

  2. Valorisation of Ca and Mg by-products from mining and seawater desalination brines for water treatment applications

    OpenAIRE

    Casas Garriga, Sandra; Aladjem, Carlos; Larrotcha, Enric; Gibert Agulló, Oriol; Valderrama Angel, César Alberto; Cortina Pallás, José Luís

    2014-01-01

    BACKGROUNDBrines from the drainage of potash mine tailings and from seawater reverse osmosis (SWRO) desalination were previously evaluated as sources of NaCl for the chlor-alkali industry. Valorisation of NaCl as raw material is required to meet the membrane electrolysis specifications of NaCl saturation and control of interferences (Ca, Mg and sulphate). Brines concentration in NaCl was previously achieved for SWRO brines using electrodialysis (ED). In this work, valorisation of Ca and Mg by...

  3. Biodegradation studies of oil sludge containing high hydrocarbons concentration

    Energy Technology Data Exchange (ETDEWEB)

    Olguin-Lora, P.; Munoz-Colunga, A.; Castorena-Cortes, G.; Roldan-Carrillo, T.; Quej Ake, L.; Reyes-Avila, J.; Zapata-Penasco, I.; Marin-Cruz, J.

    2009-07-01

    Oil industry has a significant impact on environment due to the emission of, dust, gases, waste water and solids generated during oil production all the way to basic petrochemical product manufacturing stages. the aim of this work was to evaluate the biodegradation of sludge containing high hydrocarbon concentration originated by a petroleum facility. A sludge sampling was done at the oil residuals pool (ORP) on a gas processing center. (Author)

  4. Effect of matrix components on UV/H2O2 and UV/S2O8(2-) advanced oxidation processes for trace organic degradation in reverse osmosis brines from municipal wastewater reuse facilities.

    Science.gov (United States)

    Yang, Yi; Pignatello, Joseph J; Ma, Jun; Mitch, William A

    2016-02-01

    When reverse osmosis brines from potable wastewater reuse plants are discharged to poorly-flushed estuaries, the concentrated organic contaminants are a concern for receiving water ecosystems. UV/hydrogen peroxide (UV/H2O2) and UV/persulfate (UV/S2O8(2-)) advanced oxidation processes (AOPs) may reduce contaminant burdens prior to discharge, but the effects of the high levels of halide, carbonate and effluent organic matter (EfOM) normally present in these brines are unclear. On the one hand, these substances may reduce process efficiency by scavenging reactive oxygen species (ROS), hydroxyl (OH) and sulfate (SO4(-) radicals. On the other, the daughter radicals generated by halide and carbonate scavenging may themselves degrade organics, offsetting the effect of ROS scavenging. UV/H2O2 and UV/S2O8(2-) AOPs were compared for degradation of five pharmaceuticals spiked into brines obtained from two reuse facilities and the RO influent from one of them. For UV/H2O2, EfOM scavenged ∼75% of the OH, reducing the degradation efficiency of the target contaminants to a similar extent; halide and carbonate scavenging and the reactivities of associated daughter radicals were less important. For UV/S2O8(2-), anions (mostly Cl(-)) scavenged ∼93% of the SO4(-). Because daughter radicals of Cl(-) contributed to contaminant degradation, the reduction in contaminant degradation efficiency was only ∼75-80%, with the reduction driven by daughter radical scavenging by EfOM. Conversion of SO4(-) to more selective halogen and carbonate radicals resulted in a wider range of degradation efficiencies among the contaminants. For both AOPs, 250 mJ/cm(2) average fluence achieved significant removal of four pharmaceuticals, with significantly better performance by UV/S2O8(2-) treatment for some constituents. Accounting for the lower brine flowrates, the energy output to achieve this fluence in brines is comparable to that often applied to RO permeates. However, much higher fluence was

  5. The brine shrimp artemia: adapted to critical life conditions.

    Science.gov (United States)

    Gajardo, Gonzalo M; Beardmore, John A

    2012-01-01

    The brine shrimp Artemia is a micro-crustacean, well adapted to the harsh conditions that severely hypersaline environments impose on survival and reproduction. Adaptation to these conditions has taken place at different functional levels or domains, from the individual (molecular-cellular-physiological) to the population level. Such conditions are experienced by very few equivalent macro-planktonic organisms; thus, Artemia can be considered a model animal extremophile offering a unique suite of adaptations that are the focus of this review. The most obvious is a highly efficient osmoregulation system to withstand up to 10 times the salt concentration of ordinary seawater. Under extremely critical environmental conditions, for example when seasonal lakes dry-out, Artemia takes refuge by producing a highly resistant encysted gastrula embryo (cyst) capable of severe dehydration enabling an escape from population extinction. Cysts can be viewed as gene banks that store a genetic memory of historical population conditions. Their occurrence is due to the evolved ability of females to "perceive" forthcoming unstable environmental conditions expressed by their ability to switch reproductive mode, producing either cysts (oviparity) when environmental conditions become deleterious or free-swimming nauplii (ovoviviparity) that are able to maintain the population under suitable conditions. At the population level the trend is for conspecific populations to be fragmented into locally adapted populations, whereas species are restricted to salty lakes in particular regions (regional endemism). The Artemia model depicts adaptation as a complex response to critical life conditions, integrating and refining past and present experiences at all levels of organization. Although we consider an invertebrate restricted to a unique environment, the processes to be discussed are of general biological interest. Finally, we highlight the benefits of understanding the stress response of

  6. The brine shrimp Artemia: adapted to critical life conditions

    Directory of Open Access Journals (Sweden)

    Gonzalo M Gajardo

    2012-06-01

    Full Text Available The brine shrimp Artemia is a micro-crustacean, well adapted to the harsh conditions that severely hypersaline environments impose on survival and reproduction. Adaptation to these conditions has taken place at different functional levels or domains, from the individual (molecular-cellular-physiological to the population level. Such conditions are experienced by very few equivalent macro-planktonic organisms; thus, Artemia can be considered a model animal extremophile offering a unique suite of adaptations that are the focus of this review. The most obvious is a highly efficient osmoregulation system to withstand up to 10 times the salt concentration of ordinary seawater. Under extremely critical environmental conditions, for example when seasonal lakes dry out, Artemia takes refuge by producing a highly resistant encysted gastrula embryo (cyst capable of severe dehydration enabling an escape from population extinction. Cysts can be viewed as gene banks that store a genetic memory of historical population conditions. Their occurrence is due to the evolved ability of females to perceive forthcoming unstable environmental conditions expressed by their ability to switch reproductive mode, producing either cysts (oviparity when environmental conditions become deleterious or free-swimming nauplii (ovoviviparity that are able to maintain the population under suitable conditions.At the population level the trend is for conspecific populations to be fragmented into locally adapted populations, whereas species are restricted to salty lakes in particular regions (regional endemism. The Artemia model depicts adaptation as a complex response to critical life conditions, integrating and refining past and present experiences at all levels of organization. Although we consider an invertebrate restricted to a unique environment, the processes to be discussed are of general biological interest. Finally, we highlight the benefits of understanding the stress

  7. Particle sedimentation monitoring in high-concentration slurries

    Science.gov (United States)

    Nagasawa, Yoshihiro; Kato, Zenji; Tanaka, Satoshi

    2016-11-01

    In this study, the sedimentation states of particles in high-concentration slurries were elucidated by monitoring their internal states. We prepared transparent high-concentration silica slurries by adjusting the refractive index of the aqueous glycerol liquid in which the particles were dispersed to match that of the silica particles. In addition, a fluorescent dye was dissolved in the liquid. Then, we directly observed the individual and flocculated particles in the slurries during sedimentation by confocal laser scanning fluorescent microscopy. The particles were found to sediment very slowly while exhibiting fluctuating motion. The particle sedimentation rate in the high-concentration slurry with the aqueous glycerol solution (η =0.068 Pa. s ) and a particle volume fraction on the order of 0.3 was determined to be 1.58 ± 0.66 μ m. min-1 on the basis of the obtained image sequences for 24.9 h. In-situ observation provides a large amount of information about the sedimentation behavior of particles in condensed matter.

  8. Improved Dispersion of Carbon Nanotubes in Polymers at High Concentrations

    Science.gov (United States)

    Liu, Chao-Xuan; Choi, Jin-Woo

    2012-01-01

    The polymer nanocomposite used in this work comprises elastomer poly(dimethylsiloxane) (PDMS) as a polymer matrix and multi-walled carbon nanotubes (MWCNTs) as a conductive nanofiller. To achieve uniform distribution of carbon nanotubes within the polymer, an optimized dispersion process was developed, featuring a strong organic solvent—chloroform, which dissolved PDMS base polymer easily and allowed high quality dispersion of MWCNTs. At concentrations as high as 9 wt.%, MWCNTs were dispersed uniformly through the polymer matrix, which presented a major improvement over prior techniques. The dispersion procedure was optimized via extended experimentation, which is discussed in detail. PMID:28348312

  9. Feasibility Study on High Concentrating Photovoltaic Power Towers

    Science.gov (United States)

    Frohberger, Dirk; Jaus, Joachim; Wiesenfarth, Maike; Schramek, Philipp; Bett, Andreas W.

    2010-10-01

    This paper presents an analysis on the concept of high concentrating PV power towers. A feasibility study is conducted in order to evaluate the future potential of this technology. Objective of the analysis is to provide an improved basis for establishing research and development priorities for the PV power tower concept. Performance assessments and cost calculations for a 1 MW prototype PV tower power are derived. Based on the assumption of a highly homogeneously illuminated receiver, levelized costs of electricity of 0.29 €/kWh have been calculated for a prototype PV tower power.

  10. Brine flow in heated geologic salt.

    Energy Technology Data Exchange (ETDEWEB)

    Kuhlman, Kristopher L.; Malama, Bwalya

    2013-03-01

    This report is a summary of the physical processes, primary governing equations, solution approaches, and historic testing related to brine migration in geologic salt. Although most information presented in this report is not new, we synthesize a large amount of material scattered across dozens of laboratory reports, journal papers, conference proceedings, and textbooks. We present a mathematical description of the governing brine flow mechanisms in geologic salt. We outline the general coupled thermal, multi-phase hydrologic, and mechanical processes. We derive these processes governing equations, which can be used to predict brine flow. These equations are valid under a wide variety of conditions applicable to radioactive waste disposal in rooms and boreholes excavated into geologic salt.

  11. Effects of high nitrogen concentrations on the growth of submersed macrophytes at moderate phosphorus concentrations.

    Science.gov (United States)

    Yu, Qing; Wang, Hong-Zhu; Li, Yan; Shao, Jian-Chun; Liang, Xiao-Min; Jeppesen, Erik; Wang, Hai-Jun

    2015-10-15

    Eutrophication of lakes leading to loss of submersed macrophytes and higher turbidity is a worldwide phenomenon, attributed to excessive loading of phosphorus (P). However, recently, the role of nitrogen (N) for macrophyte recession has received increasing attention. Due to the close relationship between N and P loading, disentanglement of the specific effects of these two nutrients is often difficult, and some controversy still exists as to the effects of N. We studied the effects of N on submersed macrophytes represented by Vallisneria natans (Lour.) Hara in pots positioned at three depths (0.4 m, 0.8 m, and 1.2 m to form a gradient of underwater light conditions) in 10 large ponds having moderate concentrations of P (TP 0.03 ± 0.04 mg L(-1)) and five targeted concentrations of total nitrogen (TN) (0.5, 2, 10, 20, and 100 mg L(-1)), there were two ponds for each treatment. To study the potential shading effects of other primary producers, we also measured the biomass of phytoplankton (ChlaPhyt) and periphyton (ChlaPeri) expressed as chlorophyll a. We found that leaf length, leaf mass, and root length of macrophytes declined with increasing concentrations of TN and ammonium, while shoot number and root mass did not. All the measured growth indices of macrophytes declined significantly with ChlaPhyt, while none were significantly related to ChlaPeri. Neither ChlaPhyt nor ChlaPeri were, however, significantly negatively related to the various N concentrations. Our results indicate that shading by phytoplankton unrelated to the variation in N loading and perhaps toxic stress exerted by high nitrogen were responsible for the decline in macrophyte growth.

  12. Wet oxidation of real coke wastewater containing high thiocyanate concentration.

    Science.gov (United States)

    Oulego, Paula; Collado, Sergio; Garrido, Laura; Laca, Adriana; Rendueles, Manuel; Díaz, Mario

    2014-01-01

    Coke wastewaters, in particular those with high thiocyanate concentrations, represent an important environmental problem because of their very low biodegradability. In this work, the treatment by wet oxidation of real coke wastewaters containing concentrations of thiocyanate above 17 mM has been studied in a 1-L semi-batch reactor at temperatures between 453 and 493 K, with total oxygen pressures in the range of 2.0-8.0 MPa. A positive effect of the matrix of real coke wastewater was observed, resulting in faster thiocyanate degradation than was obtained with synthetic wastewaters. Besides, the effect of oxygen concentration and temperature on thiocyanate wet oxidation was more noticeable in real effluents than in synthetic wastewaters containing only thiocyanate. It was also observed that the degree of mineralization of the matrix organic compounds was higher when the initial thiocyanate concentration increased. Taking into account the experimental data, kinetic models were obtained, and a mechanism implying free radicals was proposed for thiocyanate oxidation in the matrix considered. In all cases, sulphate, carbonates and ammonium were identified as the main reaction products of thiocyanate wet oxidation.

  13. Strategies for the production of high concentrations of bioethanol from seaweeds: production of high concentrations of bioethanol from seaweeds.

    Science.gov (United States)

    Yanagisawa, Mitsunori; Kawai, Shigeyuki; Murata, Kousaku

    2013-01-01

    Bioethanol has attracted attention as an alternative to petroleum-derived fuel. Seaweeds have been proposed as some of the most promising raw materials for bioethanol production because they have several advantages over lignocellulosic biomass. However, because seaweeds contain low contents of glucans, i.e., polysaccharides composed of glucose, the conversion of only the glucans from seaweed is not sufficient to produce high concentrations of ethanol. Therefore, it is also necessary to produce ethanol from other specific carbohydrate components of seaweeds, including sulfated polysaccharides, mannitol, alginate, agar and carrageenan. This review summarizes the current state of research on the production of ethanol from seaweed carbohydrates for which the conversion of carbohydrates to sugars is a key step and makes comparisons with the production of ethanol from lignocellulosic biomass. This review provides valuable information necessary for the production of high concentrations of ethanol from seaweeds.

  14. The brine shrimp ( Artemia parthenogenetica) as encapsulation organism for prophylactic chemotherapy of fish and prawn

    Science.gov (United States)

    Cao, Ji-Xiang; Bian, Bo-Zhong; Li, Ming-Ren

    1996-06-01

    Brine shrimp ( Artemia parthenogenetica) which had ingested three water-insoluble antibacterial drugs i.e. sulfadiazine(SD), oxytetracycline (OTC) and erythromycin estolate (ERY-Es) were fed to Tilapia and Mysis III of Penaeus orientalis K. The drug contents in the predators were then determined. After administration of drugs to Tilapia and Mysis III, through the bio-encapsulation of the brine shrimp, efficacious therapeutical concentration of OTC and ERY-Es (but not SD) in the predators could be reached and maintained for more than 8 hours.

  15. Chronic Diarrhea Associated with High Teriflunomide Blood Concentration

    OpenAIRE

    Duquette, André; Frenette, Anne Julie; Doré, Maxime

    2016-01-01

    Objective To report the case of a patient treated with leflunomide that presented with chronic diarrhea associated with high teriflunomide blood concentration. Case Summary An 84-year-old woman taking leflunomide 20 mg once daily for the past 2 years to treat rheumatoid arthritis (RA) was investigated for severe chronic diarrhea that had been worsening for the past 5 months. The patient’s general condition progressively deteriorated and included electrolyte imbalances and a transient loss of ...

  16. Effect of high soil copper concentration on mycorrhizal grapevines

    Science.gov (United States)

    Nogales, Amaia; Santos, Erika S.; Viegas, Wanda; Aran, Diego; Pereira, Sofia H.; Vidigal, Patricia; Lopes, Carlos M.; Abreu, M. Manuela

    2017-04-01

    Repeated application of Copper (Cu) based fungicides in vineyards since the end of the 19th century has led to a significant increase in the concentration of this chemical element in many viticultural soils. Although Cu is an essential micronutrient for most organisms, it can be toxic for the development and survival of plants and soil (micro)organisms at high concentrations and eventually lead to yield loses in viticulture, as it negatively affects key physiological and biogeochemical processes. However, some soil microorganisms, including arbuscular mycorrhizal fungi (AMF), have developed adaptive mechanisms for persistence in environments with supra-optimal levels of essential elements or in the presence of harmful ones, as well as for increasing plant tolerance to such abiotic stress conditions. The objective of this work was to evaluate the effect of a high total soil concentration of Cu on microbial soil activity as well as on the development of mycorrhizal and non-mycorrhizal grapevines. A microcosm assay was set up under greenhouse and controlled conditions. Touriga Nacional grapevine variety plants grafted onto 1103P rootstocks were inoculated either with the AMF Rhizophagus irregularis or Funneliformis mosseae, or were left as non-inoculated controls. After three months, they were transplanted to containers filled with 4 kg of a sandy soil (pH: 7.0; electrical conductivity: 0.08 mS/cm; [organic C]: 5.6 g/kg; [N-NO3]: 1.1 mg/kg; [N-NH4]: 2.5 mg/kg; [extractable K]: 45.1 mg/kg; [extractable P]: 52.3 mg/kg), collected near to a vineyard in Pegões (Portugal). Two treatments were carried out: with and without Cu application. The soil with high Cu concentration was prepared by adding 300 mg Cu/kg (in the form of an aqueous solution of CuSO4·5H2O) followed by an incubation during four weeks in plastic bags at room temperature in dark. Physico-chemical soil characteristics (pH, electrical conductivity and nutrients concentration in available fraction), soil

  17. Effects of brine migration on waste storage systems. Final report. [Thermomechanical effects

    Energy Technology Data Exchange (ETDEWEB)

    Gaffney, E.S.; Nickell, R.E.

    1979-05-15

    Processes which can lead to mobilization of brine adjacent to spent fuel or nuclear waste canisters and some of the thermomechanical consequences have been investigated. Velocities as high as 4 x 10/sup -7/ m s/sup -1/ (13 m y/sup -1/) are calculated at the salt/canister boundary. As much as 40 liters of pure NaCl brine could accumulate around each canister during a 10-year storage period. Accumulations of bittern brines would probably be less, in the range of 2 to 5 liters. With 0.5% water, NaCl brine accumulation over a 10-year storage cycle around a spent fuel canister producing 0.6 kW of heat is expected to be less than 1 liter for centimeter-size inclusions and less than 0.5 liter for millimeter-size inclusions. For bittern brines, about 25 years would be required to accumulate 0.4 liter. The most serious mechanical consequence of brine migration would be the increased mobility of the waste canister due to pressure solution. In pressure solution enhanced deformation, the existence of a thin film of fluid either between grains or between media (such as between a canister and the salt) provides a pathway by which the salt can be redistributed leading to a marked increase in strain rates in wet rock relative to dry rock. In salt, intergranular water will probably form discontinuous layers rather than films so that they would dominate pressure solution. A mathematical model of pressure solution indicates that pressure solution will not lead to appreciable canister motions except possibly in fine grained rocks (less than 10/sup -4/ m). In fine grained salts, details of the contact surface between the canister and the salt bed may lead to large pressure solution motions. A numerical model indicates that heat transfer in the brine layer surrounding a spent fuel canister is not conduction dominated but has a significant convective component.

  18. Particulate Matter Concentrations in East Oakland's High Street Corridor

    Science.gov (United States)

    Lei, P.; Jackson, J.; Lewis, R.; Marigny, A.; Mitchell, J. D.; Nguyen, R.; Philips, B.; Randle, D.; Romero, D.; Spears, D.; Telles, C.; Weissman, D.

    2012-12-01

    Particulate matter (PM) is a complex mixture of small solid pieces and/or liquid droplets in the air. High concentrations of PM can pose a serious health hazard because inhalation can result in breathing problems and/or aggravate asthma. Long term exposure can increase the likelihood of respiratory problems like asthma and emphysema as well as cancer. The smaller the particles, the deeper they can get into the respiratory system. For this reason, the smallest particles, those smaller than 2.5 micrometers in diameter (PM2.5), are the most dangerous. PM2.5 is largely emitted from motor vehicles burning fuels that don't break down fully. Our research team investigated the levels of PM2.5 as well as particles smaller than 10 micrometers (PM10) and total suspended particulate (TSP) along the northeast-southwest trending High Street Corridor, near Fremont High School in East Oakland, California. Using the Aerocet 531 mass particle counter, team members walked through neighborhoods and along major roads within a 1 mile radius of Fremont High School. The Aerocet 531 recorded two minute average measurements of all the relevant PM sizes, which are reported in mg/m3. Measurements were consistently taken in the morning, between 8:30 and 11:30 am. Preliminary results indicate maximum readings of all PM sizes at sites that are in close proximity to a major freeway (Interstate-880). These results support our initial hypothesis that proximity to major roads and freeways, especially those with high diesel-fuel burning truck traffic, would be the primary factor affecting PM concentration levels. Preliminary median and maximum readings all suggest particulate matter levels below what the EPA would consider unhealthy or risky.

  19. Disposal/recovery options for brine waters from oil and gas production in New York State. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Matsumoto, M.R.; Atkinson, J.F.; Bunn, M.D.; Hodge, D.S.

    1996-03-01

    Produced water from oil and gas operations, or brine as it is typically referred, may be characterized as being highly saline, with total dissolved solids greater than 100 g/L. If these bribes are disposed improperly there may be severe adverse environmental effects. Thus, it is important that brine be disposed using environmentally sound methods. Unfortunately, costs for the disposal of brine water are a significant burden to oil and gas producers in New York State. These costs and the relatively low market price of oil and natural gas have contributed to the decline in gas and oil production in New York State during the past 10 years. The objectives of this study were to evaluate new and existing options for brine disposal in New York State, examine the technical and economic merits of these options, and assess environmental impacts associated with each option. Two new disposal options investigated for New York State oil and gas producers included construction of a regional brine treatment facility to treat brine prior to discharge into a receiving water and a salt production facility that utilizes produced water as a feed stock. Both options are technically feasible; however, their economic viability depends on facility size and volume of brine treated.

  20. Influence of milk centrifugation, brining and ripening conditions in preventing gas formation by Clostridium spp. in Gouda cheese.

    Science.gov (United States)

    Su, Y C; Ingham, S C

    2000-03-25

    This study examined milk centrifugation, increased salt concentration, and low ripening temperature as potential strategies to prevent late blowing caused by gas-forming Clostridium spp. in Gouda cheese. The survival of clostridia spores in cheese brine and their ability to enter Gouda cheese during brining was also evaluated. Centrifugation (3000 x g for 30 s) of contaminated milk resulted in > 60% spore reduction, with increased spore reduction at greater centrifugal forces. Low levels of C. tyrobutyricum and C. sporogenes spores survived in saturated (23%, w/v) brine with 2% (v/v) added whey at 15 degrees C for 63 days, while C. beijerinckii and C. butyricum spores were not detectable on days 4 and 35, respectively. Spores of C. tyrobutyricum in brine infiltrated Gouda cheese during 2 h of brining at 13 degrees C resulted in production of small gas holes during ripening. In Gouda cheese slurry stored at 13 degrees C, three C. tyrobutyricum strains plus one of three C. sporogenes strains germinated in the slurry with no added salt. Of three C. tyrobutyricum strains stored at 13 degrees C in slurries with higher water-phase salt concentrations of 2.4 and 3.6%, two strains and one strain germinated, respectively. No germination of spores was detected in any cheese slurry stored at 5 or 8 degrees C. Milk centrifugation, increased percent water-phase salt, absence of spores in brine, and decreased ripening temperature are all potentially important measures against gas production by Clostridium spp. in Gouda cheese.

  1. Conceptual design of the Truscott brine lake solar-pond system, volume 1: Utility-independent scenario

    Science.gov (United States)

    1981-06-01

    A conceptual design was performed for a series of solar pond systems to provide pumping power for chloride control in the Red River Basin. In the chloride control project, briny waters are diverted so as not to pollute portable water. The diverted brine is stored in a dammed natural basin where, with the aid of natural evaporation, the brine is concentrated to the salinities required for the solar ponds. The brine is transferred to the ponds and injected at the proper levels to establish the gradients and storage layers. The solar ponds are to be located within the Truscott, Texas brine impoundment lake. Heat will be extracted from the ponds and used to drive organic Rankine-cycle turbine generators. The electricity produced will serve the pumping needs of the chloride control project, pump brine from the natural source to the evaporation ponds, pump concentrated brine from the evaporation ponds to the solar ponds, maintain the solar ponds, and supply all system parasitic loads. It was found that five solar ponds with eight organic Rankine-cycle turbine-generators would serve both the average and peaking power requirements of the pumping stations in the Truscott area as they come on-line.

  2. Ice Control with Brine on Highways

    DEFF Research Database (Denmark)

    Bolet, Lars

    During the years 1996-2006, the Division of Highways and Transportation in the former county of Funen gradually replaced pre-wetted salt with brine as de-icing agent in all her ice control activities. The replacement related to 1000 kilometres of highways. Jeopardizing neither road safety nor...

  3. Rheological Properties of Silica Nanoparticles in Brine and Brine-Surfactant Systems

    Science.gov (United States)

    Pales, Ashley; Kinsey, Erin; Li, Chunyan; Mu, Linlin; Bai, Lingyun; Clifford, Heather; Darnault, Christophe

    2016-04-01

    Rheological Properties of Silica Nanoparticles in Brine and Brine-Surfactant Systems Ashley R. Pales, Erin Kinsey, Chunyan Li, Linlin Mu, Lingyun Bai, Heather Clifford, and Christophe J. G. Darnault Department of Environmental Engineering and Earth Sciences, Laboratory of Hydrogeoscience and Biological Engineering, L.G. Rich Environmental Laboratory, Clemson University, Clemson, SC, USA Nanofluids are suspensions of nanometer sized particles in any fluid base, where the nanoparticles effect the properties of the fluid base. Commonly, nanofluids are water based, however, other bases such as ethylene-glycol, glycerol, and propylene-glycol, have been researched to understand the rheological properties of the nanofluids. This work aims to understand the fundamental rheological properties of silica nanoparticles in brine based and brine-surfactant based nanofluids with temperature variations. This was done by using variable weight percent of silica nanoparticles from 0.001% to 0.1%. Five percent brine was used to create the brine based nanofluids; and 5% brine with 2CMC of Tween 20 nonionic surfactant (Sigma-Aldrich) was used to create the brine-surfactant nanofluid. Rheological behaviors, such as shear rate, shear stress, and viscosity, were compared between these nanofluids at 20C and at 60C across the varied nanoparticle wt%. The goal of this work is to provide a fundamental basis for future applied testing for enhanced oil recovery. It is hypothesized that the addition of surfactant will have a positive impact on nanofluid properties that will be useful for enhance oil recovery. Differences have been observed in preliminary data analysis of the rheological properties between these two nanofluids indicating that the surfactant is having the hypothesized effect.

  4. 井矿盐卤水中硫酸钙颗粒沉降过程研究%Study on sedimentation process of calcium sulfate particles in well rock salt brine

    Institute of Scientific and Technical Information of China (English)

    王学魁; 李富华; 唐娜; 杜威; 张蕾; 程鹏高

    2017-01-01

    测定了硫酸钙颗粒在不同颗粒浓度和卤水浓度中沉降高度与时间的关系,测量的实际值与理论值做了对比,并分析了硫酸钙颗粒浓度和卤水浓度对硫酸钙颗粒沉降速率的影响.结果表明:沉降速率随硫酸钙颗粒浓度和卤水浓度的增加而减小;实验中的实际值远远小于理论值;硫酸钙颗粒浓度从5%(体积分数,下同)增至20%时,介质浓度高的沉降速率下降快;卤水浓度升高时,颗粒浓度高的沉降速率下降快.在纯水中,硫酸钙颗粒浓度为5%时,硫酸钙的沉降速率为19.1 mm/min.在卤水质量浓度为360 g/L、硫酸钙颗粒浓度为20%时,硫酸钙颗粒的沉降速度仅为0.33 mm/min.%The relationship between the settling height and time of calcium sulfate particles in different particle concentrat ions and brine concentrations was determined,the measured actual values and the theoretical values were compared.The effects of calcium sulfate particle concentrations and brine concentrations on the sedimentation rate of calcium sulfate particles were analyzed.Results showed that the deposition rate decreased along with the increasing of the concentrations of calcium sulfate granules and brine.The actual values in the experimnent were much smaller than the theoretical values.When the calcium sulfate particle concentration increased from 5% to 20% (volume fraction,same below),the sedimentation rate of the high concentration was decreased much more rapidly.As the brine concentration increasing,the sedimentation rate of high calcium sulfate particles was decreased quickly.The sedimentation rate was 19.10 mm/min in fresh water when the concentration of calcium sulfate particles was 5%.The sedimentation rate of calcium sulfate particles was only 0.33 mm/min when the mass concentration of brine was 360 g/L and the concentration of calcium sulfate was 20%.

  5. High manganese concentrations in rocks at Gale crater, Mars

    Science.gov (United States)

    Lanza, Nina L.; Fischer, Woodward W.; Wiens, Roger C.; Grotzinger, John; Ollila, Ann M.; Anderson, Ryan B.; Clark, Benton C.; Gellert, Ralf; Mangold, Nicolas; Maurice, Sylvestre; Le Mouélic, Stéphane; Nachon, Marion; Schmidt, Mariek E.; Berger, Jeffrey; Clegg, Samuel M.; Forni, Olivier; Hardgrove, Craig; Melikechi, Noureddine; Newsom, Horton E.; Sautter, Violaine

    2014-01-01

    The surface of Mars has long been considered a relatively oxidizing environment, an idea supported by the abundance of ferric iron phases observed there. However, compared to iron, manganese is sensitive only to high redox potential oxidants, and when concentrated in rocks, it provides a more specific redox indicator of aqueous environments. Observations from the ChemCam instrument on the Curiosity rover indicate abundances of manganese in and on some rock targets that are 1–2 orders of magnitude higher than previously observed on Mars, suggesting the presence of an as-yet unidentified manganese-rich phase. These results show that the Martian surface has at some point in time hosted much more highly oxidizing conditions than has previously been recognized.

  6. Shock initiation studies on high concentration hydrogen peroxide

    Energy Technology Data Exchange (ETDEWEB)

    Sheffield, Stephen A [Los Alamos National Laboratory; Dattelbaum, Dana M [Los Alamos National Laboratory; Stahl, David B [Los Alamos National Laboratory; Gibson, L. Lee [Los Alamos National Laboratory; Bartram, Brian D. [Los Alamos National Laboratory

    2009-01-01

    Concentrated hydrogen peroxide (H{sub 2}O{sub 2}) has been known to detonate for many years. However, because of its reactivity and the difficulty in handling and confining it, along with the large critical diameter, few studies providing basic information about the initiation and detonation properties have been published. We are conducting a study to understand and quantify the initiation and detonation properties of highly concentrated H{sub 2}O{sub 2} using a gas-driven two-stage gun to produce well defined shock inputs. Multiple magnetic gauges are used to make in-situ measurements of the growth of reaction and subsequent detonation in the liquid. These experiments are designed to be one-dimensional to eliminate any difficulties that might be encountered with large critical diameters. Because of the concern of the reactivity of the H{sub 2}O{sub 2} with the confining materials, a remote loading system has been developed. The gun is pressurized, then the cell is filled and the experiment shot within less than three minutes. TV cameras are attached to the target so the cell filling can be monitored. Several experiments have been completed on {approx}98 wt % H{sub 2}O{sub 2}/H{sub 2}O mixtures; initiation has been observed in some experiments that shows homogeneous shock initiation behavior. The initial shock pressurizes and heats the mixture. After an induction time, a thermal explosion type reaction produces an evolving reactive wave that strengthens and eventually overdrives the first wave producing a detonation. From these measurements, we have determined unreacted Hugoniot information, times (distances) to detonation (Pop-plot points) that indicate low sensitivity, and detonation velocities of high concentration H{sub 2}O{sub 2}/H{sub 2}O solutions that agree with earlier estimates.

  7. Shock initiation studies on high concentration hydrogen peroxide

    Energy Technology Data Exchange (ETDEWEB)

    Sheffield, Stephen A [Los Alamos National Laboratory; Dattelbaum, Dana M [Los Alamos National Laboratory; Stahl, David B [Los Alamos National Laboratory; Gibson, L. Lee [Los Alamos National Laboratory; Bartram, Brian D. [Los Alamos National Laboratory

    2009-01-01

    Concentrated hydrogen peroxide (H{sub 2}O{sub 2}) has been known to detonate for many years. However, because of its reactivity and the difficulty in handling and confining it, along with the large critical diameter, few studies providing basic information about the initiation and detonation properties have been published. We are conducting a study to understand and quantify the initiation and detonation properties of highly concentrated H{sub 2}O{sub 2} using a gas-driven two-stage gun to produce well defined shock inputs. Multiple magnetic gauges are used to make in-situ measurements of the growth of reaction and subsequent detonation in the liquid. These experiments are designed to be one-dimensional to eliminate any difficulties that might be encountered with large critical diameters. Because of the concern of the reactivity of the H{sub 2}O{sub 2} with the confining materials, a remote loading system has been developed. The gun is pressurized, then the cell is filled and the experiment shot within less than three minutes. TV cameras are attached to the target so the cell filling can be monitored. Several experiments have been completed on {approx}98 wt % H{sub 2}O{sub 2}/H{sub 2}O mixtures; initiation has been observed in some experiments that shows homogeneous shock initiation behavior. The initial shock pressurizes and heats the mixture. After an induction time, a thermal explosion type reaction produces an evolving reactive wave that strengthens and eventually overdrives the first wave producing a detonation. From these measurements, we have determined unreacted Hugoniot information, times (distances) to detonation (Pop-plot points) that indicate low sensitivity, and detonation velocities of high concentration H{sub 2}O{sub 2}/H{sub 2}O solutions that agree with earlier estimates.

  8. Changes of proteolysis and angiotensin-I converting enzyme-inhibitory activity in white-brined cheese as affected by adjunct culture and ripening temperature.

    Science.gov (United States)

    Sahingil, Didem; Hayaloglu, Ali A; Kirmaci, Huseyin A; Ozer, Barbaros; Simsek, Osman

    2014-11-01

    The effects of use of adjunct cultures (Lactobacillus helveticus and Lb. casei) and ripening temperatures (6 or 12 °C) on proteolysis and angiotensin-I converting enzyme (ACE)-inhibitory activity in white-brined cheeses were investigated during 120 d ripening. Proteolysis was monitored by urea-polyacrylamide gel electrophoresis (urea-PAGE) and reversed phase-HPLC (RP-HPLC) of water-insoluble and -soluble fractions of the cheeses, respectively. Urea-PAGE patterns of the samples revealed that the intensities of the bands representing casein fractions decreased in the experimental cheeses, being more pronounced in the cheeses made with adjunct cultures. Similarly, peptide profiles and the concentrations of individual and total free amino acids were influenced by both the adjunct cultures and ripening temperatures. The ACE-inhibitory activity of the water-soluble extracts of the cheeses were higher in the cheeses made using adjunct cultures (especially Lb. helveticus) and ripened at 12 °C. The ACE-inhibitory activity did not decrease during ripening. The contribution of Lb. helveticus to the development of proteolysis and ACE-inhibitory peptide activities were higher than that of Lb. casei. To conclude, the use of Lb. helveticus as adjunct culture in white-brined cheese and ripening at 12 °C would be recommended to obtain white-brined cheese with high ACE-I-inhibitory peptides activity and higher levels of preoteolysis.

  9. Experimental confirmation of liquid brines on Mars

    Science.gov (United States)

    Fischer, E.; Renno, N. O.; Martinez, G.

    2015-12-01

    The discovery of water ice and perchlorates in the shallow subsurface of Mars [1,2] is interesting because they could produce aqueous liquid solutions under Mars' present-day environmental conditions. We used the Michigan Mars Environmental Chamber [3] to simulate the pressure, temperature and relative humidity during the full diurnal cycle of sol 19 at the Phoenix landing site. Sol 19 was chosen because on this sol ice found in a shallow trench (Dodo-Goldilocks) at a depth of ~5 cm was removed with little effort [4], suggesting that it was a frozen brine (softer than freshwater ice), and because oblate spheroids found on a strut of the lander, possibly a saline mud, were observed to grow and darken (suggesting liquefaction) [4]. The results of our simulations show that early in the mission the frozen brine likely found in the Dodo-Goldilocks trench could melt in the morning, temporarily forming aqueous liquid solutions when the temperature in the trench was above the eutectic temperature of the Ca(ClO4)2 salt (~199 K). In addition, the results of our simulations indicate that the spheroids observed on a strut of the Phoenix lander were most likely droplets of liquid brines. Since halophilic terrestrial bacteria thrive in brines [5], our results suggest that Mars' polar region could potentially be a habitat for microorganisms. In addition, it has been suggested that frost could form on fine-grained terrains at Gale crater during the winter [6]. If this frost gets in contact with perchlorate salts, it could melt temporarily forming liquid brines.

  10. Source identification of high glyme concentrations in the Oder River.

    Science.gov (United States)

    Stepien, D K; Püttmann, W

    2014-05-01

    The objective of the following study was to identify the source of high concentrations of glycol diethers (diglyme, triglyme, and tetraglyme) in the Oder River. Altogether four sampling campaigns were conducted and over 50 surface samples collected. During the first two samplings of the Oder River in the Oderbruch region (km 626-690), glymes were detected at concentrations reaching 0.065 μg L(-1) (diglyme), 0.54 μg L(-1) (triglyme) and 1.7 μg L(-1) (tetraglyme). The subsequent sampling of the Oder River, from the area close to the source to the Poland-Germany border (about 500 km) helped to identify the possible area of the dominating glyme entry into the river between km 310 and km 331. During that sampling, the maximum concentration of triglyme was 0.46 μg L(-1) and tetraglyme 2.2 μg L(-1); diglyme was not detected. The final sampling focused on the previously identified area of glyme entry, as well as on tributaries of the Oder River. Samples from Czarna Woda stream and Kaczawa River contained even higher concentrations of diglyme, triglyme, and tetraglyme, reaching 5.2 μg L(-1), 13 μg L(-1) and 81 μg L(-1), respectively. Finally, three water samples were analyzed from a wastewater treatment plant receiving influents from a Copper Smelter and Refinery; diglyme, triglyme, and tetraglyme were present at a maximum concentration of 1700 μg L(-1), 13,000 μg L(-1), and 190,000 μg L(-1), respectively. Further research helped to identify the source of glymes in the wastewater. The gas desulfurization process Solinox uses a mixture of glymes (Genosorb(®)1900) as a physical absorption medium to remove sulfur dioxide from off-gases from the power plant. The wastewater generated from the process and from the maintenance of the equipment is initially directed to the wastewater treatment plant where it undergoes mechanical and chemical treatment processes before being discharged to the tributaries of the Oder River. Although monoglyme was

  11. Long term plutonium solubility and speciation studies in a synthetic brine

    Energy Technology Data Exchange (ETDEWEB)

    Nitsche, Heino; Roberts, K.; Xi, Ruihua [Lawrence Berkeley Lab., CA (United States)] [and others

    1993-12-31

    The rate at which elements can be transported in groundwater systems is governed in part by the solubility of the element in the groundwater. This report documents plutonium solubility experiments in a brine simulant relevant to the Waste Isolation Pilot Plant. Approximately 1 to 2.5 mL of five stock solutions containing single oxidation states of plutonium (Pu(IV)-polymer, Pu{sup 3+}, Pu{sup 4+}, PuO{sub 2}{sup +}, and PuO{sub 2}{sup 2+}) were added to {approximately}75 mL of synthetic H-17 Brine in five reaction vessels. Initial plutonium concentrations ranged from 1.3 {times} l0{sup {minus}4} to 5.l {times} l0{sup {minus}4} M (moles per liter) total plutonium. Because these initial concentrations were far above the plutonium solubility limit in H-17 Brine, plutonium-containing solids precipitated. Aqueous plutonium concentrations were measured over time until steady-state was reached, requiring over 300 days in H-17 Brine.

  12. Mass production of C50 carotenoids by Haloferax mediterranei in using extruded rice bran and starch under optimal conductivity of brined medium.

    Science.gov (United States)

    Chen, C Will; Hsu, Shu-hui; Lin, Ming-Tse; Hsu, Yi-hui

    2015-12-01

    Microbial carotenoids have potentially healthcare or medical applications. Haloferax mediterranei was difficult to economically grow into a large quantities as well as producing a valuable pigment of carotenoids. This study reports a novel investigation into the optimal conductivity on the mass production of carotenoids from H. mediterranei. The major component at about 52.4% in the extracted red pigment has been confirmed as bacterioruberin, a C50 carotenoids, by liquid chromatography separation and mass spectrometry analysis. By maintaining higher conductivity of 40 S/m in the brined medium, the cell concentration attained to 7.73 × 10(9) cells/L with low pigments concentration of 125 mg/L. When the conductivity was controlled at about 30 S/m, we obtained the highest cell concentration to 1.29 × 10(10) cells/L with pigments of 361.4 mg/L. When the conductivity was maintained at optimal 25 S/m, the pigments can be increased to maximum value of 555.6 mg/L at lower cell concentration of 9.22 × 10(9) cells/L. But conductivity below 20 S/m will cause the significant decrease in cell concentration as well as pigments due to the osmotic stress around the cells. Red pigment of carotenoids from an extremely halophilic archaebacterium could be efficiently produced to a high concentration by applying optimal conductivity control in the brined medium with extruded low-cost rice bran and corn starch.

  13. Metagenomic Insights into the Uncultured Diversity and Physiology of Microbes in Four Hypersaline Soda Lake Brines

    Science.gov (United States)

    Vavourakis, Charlotte D.; Ghai, Rohit; Rodriguez-Valera, Francisco; Sorokin, Dimitry Y.; Tringe, Susannah G.; Hugenholtz, Philip; Muyzer, Gerard

    2016-01-01

    Soda lakes are salt lakes with a naturally alkaline pH due to evaporative concentration of sodium carbonates in the absence of major divalent cations. Hypersaline soda brines harbor microbial communities with a high species- and strain-level archaeal diversity and a large proportion of still uncultured poly-extremophiles compared to neutral brines of similar salinities. We present the first “metagenomic snapshots” of microbial communities thriving in the brines of four shallow soda lakes from the Kulunda Steppe (Altai, Russia) covering a salinity range from 170 to 400 g/L. Both amplicon sequencing of 16S rRNA fragments and direct metagenomic sequencing showed that the top-level taxa abundance was linked to the ambient salinity: Bacteroidetes, Alpha-, and Gamma-proteobacteria were dominant below a salinity of 250 g/L, Euryarchaeota at higher salinities. Within these taxa, amplicon sequences related to Halorubrum, Natrinema, Gracilimonas, purple non-sulfur bacteria (Rhizobiales, Rhodobacter, and Rhodobaca) and chemolithotrophic sulfur oxidizers (Thioalkalivibrio) were highly abundant. Twenty-four draft population genomes from novel members and ecotypes within the Nanohaloarchaea, Halobacteria, and Bacteroidetes were reconstructed to explore their metabolic features, environmental abundance and strategies for osmotic adaptation. The Halobacteria- and Bacteroidetes-related draft genomes belong to putative aerobic heterotrophs, likely with the capacity to ferment sugars in the absence of oxygen. Members from both taxonomic groups are likely involved in primary organic carbon degradation, since some of the reconstructed genomes encode the ability to hydrolyze recalcitrant substrates, such as cellulose and chitin. Putative sodium-pumping rhodopsins were found in both a Flavobacteriaceae- and a Chitinophagaceae-related draft genome. The predicted proteomes of both the latter and a Rhodothermaceae-related draft genome were indicative of a “salt-in” strategy of

  14. Legal aspects and technical alternatives for the treatment of reservoir brines at the Activo Luna oilfield, Mexico.

    Science.gov (United States)

    Birkle, Peter; Cid Vázquez, Adolfo L; Fong Aguilar, J L

    2005-01-01

    Deep formation water, extracted as an undesired byproduct from on-shore production wells at the Activo Luna oilfield and processed in adjacent oil fields, are highly enriched in salt minerals, especially in sodium chloride (NaCl) (262 000 mg/L), but also in metals and nonmetals, such as strontium (Sr) (2068 mg/L), bromine (Br) (2034 mg/L), boron (B) (396 mg/ L), iodine (I) (43.4 mg/L), selenium (Se) (3.74 mg/L), and arsenic (As) (0.55 mg/L). Direct reinjection of the brine underground is not possible because of elevated pressure conditions within the petroleum reservoir. The disposal into near shore areas of the Gulf of Mexico without treatment must be rejected because of a) elevated concentrations of some toxic elements, such as B, silver (Ag), thallium (Tl), Se and cadmium (Cd), which exceed permissible limits of environmental legislation for surface discharge (Official Mexican norms NOM-001-ECOL-1998 and CE-CCA-001/89), and b) differences in density that could cause the descent of hypersaline fluid to the ocean floor, potentially affecting the diversity and survival of the benthic ecosystem. Conventional treatment techniques, such as microfiltration or reverse osmosis, are not suitable for the Activo Luna brines because of their extreme mineralization, which will cause pressure conditions exceeding 200 bars across the membrane. As an alternative process, the evaporation of the entire brine volume of approximately 200 m3/day by solar ponds or industrial crystallization plants is suggested. The residual precipitated residuals are composed mainly of chlorine (Cl) (9460 tons/year), sodium (Na) (4230 tons/ year), calcium (Ca) (1028 tons/year), potassium (K) (207 tons/year), and magnesium (Mg) (65.8 tons/year). As an alternative to its disposal on a dumpsite, some special minerals (especially NaCl, Mg, Sr, and Br) could be recovered for its economic value.

  15. Catalytic wet air oxidation of high concentration pharmaceutical wastewater.

    Science.gov (United States)

    Zhan, Wei; Wang, Xiaocong; Li, Daosheng; Ren, Yongzheng; Liu, Dongqi; Kang, Jianxiong

    2013-01-01

    In this study, we investigated the pretreatment of a high concentration pharmaceutical wastewater by catalytic wet air oxidation (CWAO) process. Different experiments were conducted to investigate the effects of the catalyst type, operating temperature, initial system pH, and oxygen partial pressure on the oxidation of the wastewater. Results show that the catalysts prepared by the co-precipitation method have better catalytic activity compared to others. Chemical oxygen demand (COD) conversion increased with the increase in temperature from 160 to 220 °C and decreased with the increase in pH. Moreover, the effect of the oxygen partial pressure on the COD conversion was significant only during the first 20 min of the reaction. Furthermore, the biodegradability of the wastewater improved greatly after CWAO, the ratio of BOD5/COD increased less than 0.1-0.75 when treated at 220 °C (BOD: biochemical oxygen demand).

  16. Acquisition and Analysis of Data from High Concentration Solutions

    KAUST Repository

    Besong, Tabot M.D.

    2016-05-13

    The problems associated with ultracentrifugal analysis of macromolecular solutions at high (>10 mg/ml) are reviewed. Especially for the case of solutes which are non-monodisperse, meaningful results are not readily achievable using sedimentation velocity approaches. It is shown however by both simulation and analysis of practical data that using a modified form of an algorithm (INVEQ) published in other contexts, sedimentation equilibrium (SE) profiles can be analysed successfully, enabling topics such as oligomer presence or formation to be defined.To achieve this, it is necessary to employ an approach in which the solution density, which in an SE profile is radius-dependent, is taken into consideration. Simulation suggests that any reasonable level of solute concentration can be analysed.

  17. Rheological properties of highly concentrated protein-stabilized emulsions.

    Science.gov (United States)

    Dimitrova, Tatiana D; Leal-Calderon, Fernando

    2004-05-20

    We prepared concentrated quasi monodisperse hexadecane-in-water emulsions stabilized by various proteins and investigated their rheological properties. Some protein-stabilized emulsions possess remarkably high elasticity and at the same time they are considerably fragile--they exhibit coalescence at yield strain and practically do not flow. The elastic storage modulus G' and the loss modulus G" of the emulsions were determined for different oil volume fractions above the random close packing. Surprisingly, the dimensionless elastic moduli G'/(sigma/a), sigma being the interfacial tension, and a being the mean drop radius, obtained for emulsions stabilized by different proteins do not collapse on a single master curve. They are almost always substantially higher than the corresponding values obtained for equivalent Sodium Dodecyl Sulfate (SDS)-stabilized emulsions. The unusually high elasticity cannot be attributed to a specificity of the continuous phase, because the osmotic equation of state of our emulsions is found identical to the one obtained for samples stabilized by classical surfactants. In parallel, we mimicked the thin films that separate the droplets in the concentrated emulsion and found that the protein adsorption layers contain a substantial number of sticky surface aggregates. These severely obstruct local rearrangements of individual drops in respect to their neighbors which leads to coalescence at yield strain. Furthermore, we found that G'/(sigma/a) is correlated (for a given oil volume fraction) to the dilatational elastic modulus, of the protein layer adsorbed on the droplets. The intrinsic elasticity of the protein layers, together with the blocked local rearrangements are considered as the main factors determining the unusual bulk elasticity of the studied emulsions.

  18. Do high concentrations of microcystin prevent Daphnia control of phytoplankton?

    Science.gov (United States)

    Chislock, Michael F; Sarnelle, Orlando; Jernigan, Lauren M; Wilson, Alan E

    2013-04-15

    Toxin-producing cyanobacteria have frequently been hypothesized to limit the ability of herbivorous zooplankton (such as Daphnia) to control phytoplankton biomass by inhibiting feeding, and in extreme cases, causing zooplankton mortality. Using limnocorral experiments in hyper-eutrophic ponds located in Alabama and Michigan (U.S.A.), we tested the hypothesis that high levels of cyanobacteria and microcystin, a class of hepatotoxins produced by several cyanobacterial genera, prevent Daphnia from strongly reducing phytoplankton abundance. At the start of the first experiment (Michigan), phytoplankton communities were dominated by toxic Microcystis and Anabaena (∼96% of total phytoplankton biomass), and concentrations of microcystin were ∼3 μg L⁻¹. Two weeks after adding Daphnia pulicaria from a nearby eutrophic lake, microcystin levels increased to ∼6.5 μg L⁻¹, yet Daphnia populations increased exponentially (r = 0.24 day⁻¹). By the third week, Daphnia had suppressed phytoplankton biomass by ∼74% relative to the no Daphnia controls and maintained reduced phytoplankton biomass until the conclusion of the five-week experiment. In the second experiment (Alabama), microcystin concentrations were greater than 100 μg L⁻¹, yet a mixture of three D. pulicaria clones from eutrophic lakes in southern MI increased and again reduced phytoplankton biomass, in this case by over 80%. The ability of Daphnia to increase in abundance and suppress phytoplankton biomass, despite high initial levels of cyanobacteria and microcystin, indicates that the latter does not prevent strong control of phytoplankton biomass by Daphnia genotypes that are adapted to environments with abundant cyanobacteria and associated cyanotoxins.

  19. Highly Concentrated Acetic Acid Poisoning: 400 Cases Reviewed

    Directory of Open Access Journals (Sweden)

    Konstantin Brusin

    2012-12-01

    Full Text Available Background: Caustic substance ingestion is known for causing a wide array of gastrointestinal and systemic complications. In Russia, ingestion of acetic acid is a major problem which annually affects 11.2 per 100,000 individuals. The objective of this study was to report and analyze main complications and outcomes of patients with 70% concentrated acetic acid poisoning. Methods: This was a retrospective study of patients with acetic acid ingestion who were treated at Sverdlovsk Regional Poisoning Treatment Center during 2006 to 2012. GI mucosal injury of each patient was assessed with endoscopy according to Zargar’s scale. Data analysis was performed to analyze the predictors of stricture formation and mortality. Results: A total of 400 patients with median age of 47 yr were included. GI injury grade I was found in 66 cases (16.5%, IIa in 117 (29.3%, IIb in 120 (30%, IIIa in 27 (16.7% and IIIb in 70 (17.5%. 11% of patients developed strictures and overall mortality rate was 21%. Main complications were hemolysis (55%, renal injury (35%, pneumonia (27% and bleeding during the first 3 days (27%. Predictors of mortality were age 60 to 79 years, grade IIIa and IIIb of GI injury, pneumonia, stages “I”, “F” and “L” of kidney damage according to the RIFLE scale and administration of prednisolone. Predictors of stricture formation were ingestion of over 100 mL of acetic acid and grade IIb and IIIa of GI injury. Conclusion: Highly concentrated acetic acid is still frequently ingested in Russia with a high mortality rate. Patients with higher grades of GI injury, pneumonia, renal injury and higher amount of acid ingested should be more carefully monitored as they are more susceptible to develop fatal consequences.          

  20. Kinetics of nitrate and perchlorate reduction in ion-exchange brine using the membrane biofilm reactor (MBfR).

    Science.gov (United States)

    Van Ginkel, Steven W; Ahn, Chang Hoon; Badruzzaman, Mohammad; Roberts, Deborah J; Lehman, S Geno; Adham, Samer S; Rittmann, Bruce E

    2008-09-01

    Several sources of bacterial inocula were tested for their ability to reduce nitrate and perchlorate in synthetic ion-exchange spent brine (30-45 g/L) using a hydrogen-based membrane biofilm reactor (MBfR). Nitrate and perchlorate removal fluxes reached as high as 5.4 g Nm(-2)d(-1) and 5.0 g ClO(4)m(-2)d(-1), respectively, and these values are similar to values obtained with freshwater MBfRs. Nitrate and perchlorate removal fluxes decreased with increasing salinity. The nitrate fluxes were roughly first order in H(2) pressure, but roughly zero-order with nitrate concentration. Perchlorate reduction rates were higher with lower nitrate loadings, compared to high nitrate loadings; this is a sign of competition for H(2). Nitrate and perchlorate reduction rates depended strongly on the inoculum. An inoculum that was well acclimated (years) to nitrate and perchlorate gave markedly faster removal kinetics than cultures that were acclimated for only a few months. These results underscore that the most successful MBfR bioreduction of nitrate and perchlorate in ion-exchange brine demands a well-acclimated inoculum and sufficient hydrogen availability.

  1. Pure Culture Fermentation of Brined Cucumbers.

    Science.gov (United States)

    Etchells, J L; Costilow, R N; Anderson, T E; Bell, T A

    1964-11-01

    The relative abilities of Pediococcus cerevisiae, Lactobacillus plantarum, L. brevis, and several other species of lactic acid bacteria to grow and produce acid in brined cucumbers were evaluated in pure culture fermentations. Such fermentations were made possibly by the use of two techniques, gamma radiation (0.83 to 1.00 Mrad) and hot-water blanching (66 to 80 C for 5 min), designed first to rid the cucumbers of naturally occurring, interfering, and competitive microbial groups prior to brining, followed by inoculation with the desired lactic acid bacteria. Of the nine species tested, strains of the three common to cucumber fermentations, P. cerevisiae, L. plantarum, and L. brevis, grew to the highest populations, and produced the highest levels of brine acidity and the lowest pH values in fermentations at 5.4 to 5.6% NaCl by weight; also, their sequence of active development in fermentations, with the use of a three-species mixture for inoculation, was in the species order just named. This sequence of occurrence was similar to that estimated by others for natural fermentations. The rates of growth and acid production in fermentations with a mixture of P. cerevisiae, L. plantarum, and L. brevis increased as the incubation temperature was increased from 21 to 27 to 32 C; however, the maximal populations and acidities attained were essentially the same for fermentations at each temperature. Further, these same three species were found to be the most salt tolerant of those tested; their upper limit for appreciable growth and measurable acid production was about 8% salt, whereas thermophilic species such as L. thermophilus, L. lactis, L. helveticus, L. fermenti, and L. delbrueckii exhibited a much lower salt tolerance, ranging from about 2.5 to 4.0%. However, certain strains of L. delbrueckii grew very rapidly in cucumbers brined at 2.5 to 3.0% salt, and produced sufficient acid in about 30 hr at 48 C to reduce the brine pH from above 7.0 to below 4.0. An inexpensive

  2. Understanding the role of brine ionic composition on oil recovery by assessment of wettability from colloidal forces.

    Science.gov (United States)

    Alshakhs, Mohammed J; Kovscek, Anthony R

    2016-07-01

    The impact of injection brine salinity and ionic composition on oil recovery has been an active area of research for the past 25years. Evidence from laboratory studies and field tests suggests that implementing certain modifications to the ionic composition of the injection brine leads to greater oil recovery. The role of salinity modification is attributed to its ability to shift wettability of a rock surface toward water wetness. The amount of trapped oil released depends on the nature of rock, oil, and brine surface interactions. Reservoir rocks exhibit different affinities to fluids. Carbonates show stronger adsorption of oil films as opposed to the strongly water-wet and mixed-wet sandstones. The concentration of divalent ions and total salinity of the injection brine are other important factors to consider. Accordingly, this paper provides a review of laboratory and field studies of the role of brine composition on oil recovery from carbonaceous rock as well as rationalization of results using DLVO (Derjaguin, Landau, Verwey and Overbeek) theory of surface forces. DLVO evaluates the contribution of each component of the oil/brine/rock system to the wettability. Measuring zeta potential of each pair of surfaces by a charged particle suspension method is used to estimate double layer forces, disjoining pressure, and contact-angle. We demonstrate the applicability of the DLVO approach by showing a comprehensive experimental study that investigates the effect of divalent ions in carbonates, and uses disjoining pressure results to rationalize observations from core flooding and direct contact-angle measurements.

  3. Inland Treatment of the Brine Generated from Reverse Osmosis Advanced Membrane Wastewater Treatment Plant Using Epuvalisation System

    Science.gov (United States)

    Qurie, Mohannad; Abbadi, Jehad; Scrano, Laura; Mecca, Gennaro; Bufo, Sabino A.; Khamis, Mustafa; Karaman, Rafik

    2013-01-01

    The reverse osmosis (RO) brine generated from the Al-Quds University wastewater treatment plant was treated using an epuvalisation system. The advanced integrated wastewater treatment plant included an activated sludge unit, two consecutive ultrafiltration (UF) membrane filters (20 kD and 100 kD cutoffs) followed by an activated carbon filter and a reverse osmosis membrane. The epuvalisation system consisted of salt tolerant plants grown in hydroponic channels under continuous water flowing in a closed loop system, and placed in a greenhouse at Al-Quds University. Sweet basil (Ocimum basilicum) plants were selected, and underwent two consecutive hydroponic flowing stages using different brine-concentrations: an adaptation stage, in which a 1:1 mixture of brine and fresh water was used; followed by a functioning stage, with 100% brine. A control treatment using fresh water was included as well. The experiment started in April and ended in June (2012). At the end of the experiment, analysis of the effluent brine showed a remarkable decrease of electroconductivity (EC), PO43−, chemical oxygen demand (COD) and K+ with a reduction of 60%, 74%, 70%, and 60%, respectively, as compared to the influent. The effluent of the control treatment showed 50%, 63%, 46%, and 90% reduction for the same parameters as compared to the influent. Plant growth parameters (plant height, fresh and dry weight) showed no significant difference between fresh water and brine treatments. Obtained results suggest that the epuvalisation system is a promising technique for inland brine treatment with added benefits. The increasing of channel number or closed loop time is estimated for enhancing the treatment process and increasing the nutrient uptake. Nevertheless, the epuvalisation technique is considered to be simple, efficient and low cost for inland RO brine treatment. PMID:23823802

  4. Inland Treatment of the Brine Generated from Reverse Osmosis Advanced Membrane Wastewater Treatment Plant Using Epuvalisation System

    Directory of Open Access Journals (Sweden)

    Mohannad Qurie

    2013-07-01

    Full Text Available The reverse osmosis (RO brine generated from the Al-Quds University wastewater treatment plant was treated using an epuvalisation system. The advanced integrated wastewater treatment plant included an activated sludge unit, two consecutive ultrafiltration (UF membrane filters (20 kD and 100 kD cutoffs followed by an activated carbon filter and a reverse osmosis membrane. The epuvalisation system consisted of salt tolerant plants grown in hydroponic channels under continuous water flowing in a closed loop system, and placed in a greenhouse at Al-Quds University. Sweet basil (Ocimum basilicum plants were selected, and underwent two consecutive hydroponic flowing stages using different brine-concentrations: an adaptation stage, in which a 1:1 mixture of brine and fresh water was used; followed by a functioning stage, with 100% brine. A control treatment using fresh water was included as well. The experiment started in April and ended in June (2012. At the end of the experiment, analysis of the effluent brine showed a remarkable decrease of electroconductivity (EC, PO43−, chemical oxygen demand (COD and K+ with a reduction of 60%, 74%, 70%, and 60%, respectively, as compared to the influent. The effluent of the control treatment showed 50%, 63%, 46%, and 90% reduction for the same parameters as compared to the influent. Plant growth parameters (plant height, fresh and dry weight showed no significant difference between fresh water and brine treatments. Obtained results suggest that the epuvalisation system is a promising technique for inland brine treatment with added benefits. The increasing of channel number or closed loop time is estimated for enhancing the treatment process and increasing the nutrient uptake. Nevertheless, the epuvalisation technique is considered to be simple, efficient and low cost for inland RO brine treatment.

  5. Inland treatment of the brine generated from reverse osmosis advanced membrane wastewater treatment plant using epuvalisation system.

    Science.gov (United States)

    Qurie, Mohannad; Abbadi, Jehad; Scrano, Laura; Mecca, Gennaro; Bufo, Sabino A; Khamis, Mustafa; Karaman, Rafik

    2013-07-03

    The reverse osmosis (RO) brine generated from the Al-Quds University wastewater treatment plant was treated using an epuvalisation system. The advanced integrated wastewater treatment plant included an activated sludge unit, two consecutive ultrafiltration (UF) membrane filters (20 kD and 100 kD cutoffs) followed by an activated carbon filter and a reverse osmosis membrane. The epuvalisation system consisted of salt tolerant plants grown in hydroponic channels under continuous water flowing in a closed loop system, and placed in a greenhouse at Al-Quds University. Sweet basil (Ocimum basilicum) plants were selected, and underwent two consecutive hydroponic flowing stages using different brine-concentrations: an adaptation stage, in which a 1:1 mixture of brine and fresh water was used; followed by a functioning stage, with 100% brine. A control treatment using fresh water was included as well. The experiment started in April and ended in June (2012). At the end of the experiment, analysis of the effluent brine showed a remarkable decrease of electroconductivity (EC), PO43-, chemical oxygen demand (COD) and K+ with a reduction of 60%, 74%, 70%, and 60%, respectively, as compared to the influent. The effluent of the control treatment showed 50%, 63%, 46%, and 90% reduction for the same parameters as compared to the influent. Plant growth parameters (plant height, fresh and dry weight) showed no significant difference between fresh water and brine treatments. Obtained results suggest that the epuvalisation system is a promising technique for inland brine treatment with added benefits. The increasing of channel number or closed loop time is estimated for enhancing the treatment process and increasing the nutrient uptake. Nevertheless, the epuvalisation technique is considered to be simple, efficient and low cost for inland RO brine treatment.

  6. Modelling acceptance of sunlight in high and low photovoltaic concentration

    Energy Technology Data Exchange (ETDEWEB)

    Leutz, Ralf, E-mail: ralf.leutz@leopil.com [Leutz Optics and Illumination UG (haftungsbeschränkt), Marburg (Germany)

    2014-09-26

    A simple model incorporating linear radiation characteristics, along with the optical trains and geometrical concentration ratios of solar concentrators is presented with performance examples for optical trains of HCPV, LCPV and benchmark flat-plate PV.

  7. Design philosophy and construction of a high concentration compound parabolic concentrator

    CSIR Research Space (South Africa)

    Roos, TH

    2010-09-01

    Full Text Available A compound parabolic concentrator (CPC) with a concentration ratio of 16:1 is under development at CSIR for volumetric receiver and solar fuels development. The ideal shape has been approximated by 6 and 12 facets in the longitudinal...

  8. Microbial diversity and activity in seafloor brine lake sediments (Alaminos Canyon block 601, Gulf of Mexico).

    Science.gov (United States)

    Crespo-Medina, M; Bowles, M W; Samarkin, V A; Hunter, K S; Joye, S B

    2016-09-01

    The microbial communities thriving in deep-sea brines are sustained largely by energy rich substrates supplied through active seepage. Geochemical, microbial activity, and microbial community composition data from different habitats at a Gulf of Mexico brine lake in Alaminos Canyon revealed habitat-linked variability in geochemistry that in turn drove patterns in microbial community composition and activity. The bottom of the brine lake was the most geochemically extreme (highest salinity and nutrient concentrations) habitat and its microbial community exhibited the highest diversity and richness indices. The habitat at the upper halocline of the lake hosted the highest rates of sulfate reduction and methane oxidation, and the largest inventories of dissolved inorganic carbon, particulate organic carbon, and hydrogen sulfide. Statistical analyses indicated a significant positive correlation between the bacterial and archaeal diversity in the bottom brine sample and NH4+ inventories. Other environmental factors with positive correlation with microbial diversity indices were DOC, H2 S, and DIC concentrations. The geochemical regime of different sites within this deep seafloor extreme environment exerts a clear selective force on microbial communities and on patterns of microbial activity.

  9. High-performance deployable structures for the support of high-concentration ratio solar array modules

    Science.gov (United States)

    Mobrem, M.

    1985-01-01

    A study conducted on high-performance deployable structures for the support of high-concentration ratio solar array modules is discussed. Serious consideration is being given to the use of high-concentration ratio solar array modules or applications such as space stations. These concentrator solar array designs offer the potential of reduced cost, reduced electrical complexity, higher power per unit area, and improved survivability. Arrays of concentrators, such as the miniaturized Cassegrainian concentrator modules, present a serious challenge to the structural design because their mass per unit area (5.7 kg/square meters) is higher than that of flexible solar array blankets, and the requirement for accurate orientation towards the Sun (plus or minus 0.5 degree) requires structures with improved accuracy potentials. In addition, use on a space station requires relatively high structural natural frequencies to avoid deleterious interactions with control systems and other large structural components. The objective here is to identify and evaluate conceptual designs of structures suitable for deploying and accurately supporting high-concentration ratio solar array modules.

  10. Design and development of a high-concentration and high-efficiency photovoltaic concentrator using a curved Fresnel lens

    Energy Technology Data Exchange (ETDEWEB)

    Scharlack, R.S.; Moffat, A.

    1983-08-01

    Thermo Electron has designed a high concentration photovoltaic module that uses a domed, point-focus Fresnel lens. Their design, design optimization process, and results from lens and receiver tests are described in this report. A complete module has not been fabricated and probably will not be fabricated in the future; however, Thermo Electron's optical design, analysis, and testing of both secondary optical units and domed Fresnel lenses have made a significant contribution to our project. Tooling errors prevented the lens from reaching its potential efficiency by the end of the contract, and resolution of these tooling problems is currently being attempted with a follow-on contract, No. 68-9463.

  11. Survival of Bifidobacterium longum and its effect on physicochemical properties and sensorial attributes of white brined cheese.

    Science.gov (United States)

    Gursoy, Oguz; Gokce, Ramazan; Con, Ahmet Hilmi; Kinik, Ozer

    2014-11-01

    Survival of the probiotic adjunct culture Bifidobacterium longum and cheese starters during ripening of white brined cheese, effect of the probiotic culture on physicochemical properties and sensorial attributes of cheeses were investigated throughout 90 d of ripening. Bifidobacterium longum were able to survive at higher levels (>10(7 )cfu/g cheese) than the therapeutic minimum (10(6)-10(7 )cfu/g cheese) after 90 d and did not have any negative effect on the survival of Streptococcus spp. (including common cheese starters). Incorporation of the probiotic adjunct into white brined cheese and high levels of their survival rates during ripening had an insignificant effect on the composition of cheeses. Results indicated that white brined cheese is a suitable food matrix for the delivery of B. longum used in this study, and white brined cheeses with B. longum may be considered as a probiotic dairy product.

  12. Phylogenetic analysis of bacteria in sea ice brine sampled from the Canada Basin, Arctic Ocean

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Bacterial diversity in sea ice brine samples which collected from four stations located at the Canada Basin, Arctic Ocean was analyzed by PCR-DGGE. Twenty-three 16S rDNA sequences of bacteria obtained from DGGE bands were cloned and sequenced. Phylogenetic analysis clustered these sequences within γ-proteobacteria, Cytophaga-Flexibacter-Bacteroides (CFB) group, Firmicutes and Actinobacteria. The phylotype of Pseudoalteromonas in the γ-proteobacteria was predominant and members of the CFB group and γ-proteobacteria were highly abundant in studied sea ice brine samples.

  13. In-Situ X-ray Tomography Study of Cement Exposed to CO2 Saturated Brine

    DEFF Research Database (Denmark)

    Chavez Panduro, E. A.; Torsæter, M.; Gawel, K.

    2017-01-01

    saturated brine is required. Here, we report in situ X-ray micro computed tomography (μ-CT) studies visualizing the microstructural changes upon exposure of cured Portland cement with an artificially engineered leakage path (cavity) to CO2 saturated brine at high pressure. Carbonation of the bulk cement......, self-healing of the leakage path in the cement specimen, and leaching of CaCO3 were thus directly observed. The precipitation of CaCO3, which is of key importance as a possible healing mechanism of fractured cement, was found to be enhanced in confined regions having limited access to CO2...

  14. A preliminary deposit model for lithium brines

    Science.gov (United States)

    Bradley, Dwight; Munk, LeeAnn; Jochens, Hillary; Hynek, Scott; Labay, Keith A.

    2013-01-01

    This report is part of an effort by the U.S. Geological Survey to update existing mineral deposit models and to develop new ones. The global transition away from hydrocarbons toward energy alternatives increases demand for many scarce metals. Among these is lithium, a key component of lithium-ion batteries for electric and hybrid vehicles. Lithium brine deposits account for about three-fourths of the world’s lithium production. Updating an earlier deposit model, we emphasize geologic information that might directly or indirectly help in exploration for lithium brine deposits, or for assessing regions for mineral resource potential. Special attention is given to the best-known deposit in the world—Clayton Valley, Nevada, and to the giant Salar de Atacama, Chile.

  15. Molecular Dynamics Simulation Study of Carbon Dioxide, Methane, and Their Mixture in the Presence of Brine

    KAUST Repository

    Yang, Yafan

    2017-10-03

    We perform molecular dynamics simulation study of CO2, methane, and their mixture in the presence of brine over a broad range of temperature (311–473 K), pressure (up to about 100 MPa), and NaCl concentration (up to about 14 wt %). The general decrease in the interfacial tension (IFT) values of the CH4–brine system with pressure and temperature is similar to that obtained for the corresponding CH4–water system. The IFT of methane and brine is a linearly increasing function of salt concentration, and the resulting slopes are dependent on the pressure. A similar behavior as methane is observed for such systems containing CO2 and CO2–CH4 mixture. The IFT of CO2 and brine increases linearly with increasing salt content; however, the resulting slopes are independent of pressure. The simulations show that the presence of CO2 decreases the IFT values of the CH4–water and CH4–brine systems, but the degree of reduction depends on the amount of CO2 in each sample, which is consistent with experimental evidence. These IFT values show a linear correlation with the amount of CO2, and the resulting slopes are dependent on the temperature and pressure. Furthermore, our results for the mole fractions of the different species in the CO2–CH4–water system at 323 K and 9 MPa are in agreement with those of experiments. The mole fractions of methane and CO2 in the water-rich phase decrease with increasing salt concentration, whereas that of H2O in the methane- or CO2-rich phases remains almost unaffected in all of the studied cases. Our results could be useful because of the importance of carbon dioxide sequestration and shale gas production.

  16. Brine shrimp lethality assay of Bacopa monnieri.

    Science.gov (United States)

    D'Souza, Prashanth; Deepak, Mundkinajeddu; Rani, Padmaja; Kadamboor, Sandhya; Mathew, Anjana; Chandrashekar, Arun P; Agarwal, Amit

    2002-03-01

    Successive petroleum ether, chloroform, ethanol and water extracts, a saponin rich fraction (SRF) and bacoside A isolated from Bacopa monnieri were tested for brine shrimp lethality. Successive ethanol extracts and SRF showed potent activity. Bacoside A showed the maximum activity with a LC(50) of 38.3 microg/mL. The results confirmed the previous reports of an anticancer effect of Bacopa monnieri and suggest bacoside A as the active constituent.

  17. Interstitial brines in playa sediments

    Science.gov (United States)

    Jones, B.F.; Van Denburgh, A.S.; Truesdell, A.H.; Rettig, S.L.

    1969-01-01

    Study of several closed drainages in the Great Basin has shown that the interstitial solutions of shallow, fine-grained playa deposits store a large quantity of dissolved solids and are often more concentrated than associated lakes and ponds, except in peripheral zones of stream or ground-water inflow. These interstitial fluids, when compared with local runoff, impoundments, or spring waters, commonly have a distinctive ionic composition which sometimes cannot be explained by either simple mixing of surface and subsurface inflow or by evaporative concentration. At Abert Lake, Oregon, the interstitial solute concentrations increased with depth to values as much as five times greater than the lake, except where springs indicate significant ground-water input. Where Na+, Cl, and CO2 species constitute more than 90% of the solutes, Na+ Cl- ratios in the lake water are lower than in interstitial solutions of bottom cores and higher than in playa fluids. At the same time, Na+ K+ ratios are highest in the fluids of lake bottom muds and lowest in playa interstitials. In deeper playa profiles, interstitial Na+ Cl- tended to decrease with depth (5 ft. maximum). In the Abert Lake area, as in other parts of the western Great Basin, Na+ Cl- ratios are indicative of total CO2 in solution and the effects of organic decay in surficial sediments. These ratios, coupled with data on silica and bulk density, show that higher PCO2 accompanying decay promotes silicate dissolution and hydrogen ion exchange, stripping alkalis from sediment which had preferentially adsorbed K+ when entering the lake. On subsequent loss of pore fluid in the playa regime, silica initially released to solution in the lake environment is readsorbed on dissolution products. ?? 1969.

  18. Carbon Nanofibers Modified Graphite Felt for High Performance Anode in High Substrate Concentration Microbial Fuel Cells

    Directory of Open Access Journals (Sweden)

    Youliang Shen

    2014-01-01

    Full Text Available Carbon nanofibers modified graphite fibers (CNFs/GF composite electrode was prepared for anode in high substrate concentration microbial fuel cells. Electrochemical tests showed that the CNFs/GF anode generated a peak current density of 2.42 mA cm−2 at a low acetate concentration of 20 mM, which was 54% higher than that from bare GF. Increase of the acetate concentration to 80 mM, in which the peak current density of the CNFs/GF anode greatly increased and was up to 3.57 mA cm−2, was seven times as that of GF anode. Morphology characterization revealed that the biofilms in the CNFs/GF anode were much denser than those in the bare GF. This result revealed that the nanostructure in the anode not only enhanced current generation but also could tolerate high substrate concentration.

  19. An Automatic High Efficient Method for Dish Concentrator Alignment

    OpenAIRE

    Yong Wang; Song Li; Jinshan Xu; Yijiang Wang; Xu Cheng; Changgui Gu; Shengyong Chen; Bin Wan

    2014-01-01

    Alignment of dish concentrator is a key factor to the performance of solar energy system. We propose a new method for the alignment of faceted solar dish concentrator. The isosceles triangle configuration of facet’s footholds determines a fixed relation between light spot displacements and foothold movements, which allows an automatic determination of the amount of adjustments. Tests on a 25 kW Stirling Energy System dish concentrator verify the feasibility, accuracy, and efficiency of our...

  20. Ice-brine and planktonic microheterotrophs from Saroma-ko Lagoon, Hokkaido (Japan): quantitative importance and trophodynamics

    Science.gov (United States)

    Sime-Ngando, Télesphore; Juniper, S. Kim; Demers, Serge

    1997-02-01

    Biologists have rarely had the opportunity to investigate the community characteristics and dynamics of heterotrophic microorganisms in highly productive first-year sea ice. In this study, sterile seawater was used as a salinity buffer to extract the ice-brine microheterotroph communities (bacteria, flagellates and ciliates) from a coastal lagoon in Japan (Saroma-ko, Hokkaido; 44°N, 144°E) during the late winter (February—March) of 1992. This procedure reduced osmotic shock during the melting of ice cores and allowed the recovery of up to 323% more cells than the traditional melting method. Most of the organisms were concentrated in the bottom 3-4 cm of the ice, where abundances were up to 33 times higher than in the plankton. In ice and plankton samples, heterotrophic flagellates were dominated by small species (sampling period while protozoa increased or attained their maximum number in late winter, toward the end of the sampling period. These observations support previous suggestions of the existence of a functional microbial food web within the sea-ice community. Heterotrophic flagellate biomass greatly exceeded bacterial biomass in the sea ice (30-60 x). Coupled with similar potential growth rates, this suggests the utilization of additional (non-bacterial) food items by ice-brine flagellates. Finally, the effects of salinity variations (ranging between 15 and 120 psu) on potential microheterotroph growth rates are discussed.

  1. Selection of common bean lines with high grain yield and high grain calcium and iron concentrations

    Directory of Open Access Journals (Sweden)

    Nerinéia Dalfollo Ribeiro

    2014-02-01

    Full Text Available Genetic improvement of common bean nutritional quality has advantages in marketing and can contribute to society as a food source. The objective of this study was to evaluate the genetic variability for grain yield, calcium and iron concentrations in grains of inbred common bean lines obtained by different breeding methods. For this, 136 F7 inbred lines were obtained using the Pedigree method and 136 F7 inbred lines were obtained using the Single-Seed Descent (SSD method. The lines showed genetic variability for grain yield, and concentrations of calcium and iron independently of the method of advancing segregating populations. The Pedigree method allows obtaining a greater number of lines with high grain yield. Selection using the SSD method allows the identification of a larger number of lines with high concentrations of calcium and iron in grains. Weak negative correlations were found between grain yield and calcium concentration (r = -0.0994 and grain yield and iron concentration (r = -0.3926. Several lines show genetic superiority for grain yield and concentrations of calcium and iron in grains and their selection can result in new common bean cultivars with high nutritional quality.

  2. Brine assemblages of ultrasmall microbial cells within the ice cover of Lake Vida, Antarctica.

    Science.gov (United States)

    Kuhn, Emanuele; Ichimura, Andrew S; Peng, Vivian; Fritsen, Christian H; Trubl, Gareth; Doran, Peter T; Murray, Alison E

    2014-06-01

    The anoxic and freezing brine that permeates Lake Vida's perennial ice below 16 m contains an abundance of very small (≤0.2-μm) particles mixed with a less abundant population of microbial cells ranging from >0.2 to 1.5 μm in length. Fluorescent DNA staining, electron microscopy (EM) observations, elemental analysis, and extraction of high-molecular-weight genomic DNA indicated that a significant portion of these ultrasmall particles are cells. A continuous electron-dense layer surrounding a less electron-dense region was observed by EM, indicating the presence of a biological membrane surrounding a cytoplasm. The ultrasmall cells are 0.192 ± 0.065 μm, with morphology characteristic of coccoid and diplococcic bacterial cells, often surrounded by iron-rich capsular structures. EM observations also detected the presence of smaller unidentified nanoparticles of 0.020 to 0.140 μm among the brine cells. A 16S rRNA gene clone library from the brine 0.1- to 0.2-μm-size fraction revealed a relatively low-diversity assemblage of Bacteria sequences distinct from the previously reported >0.2-μm-cell-size Lake Vida brine assemblage. The brine 0.1- to 0.2-μm-size fraction was dominated by the Proteobacteria-affiliated genera Herbaspirillum, Pseudoalteromonas, and Marinobacter. Cultivation efforts of the 0.1- to 0.2-μm-size fraction led to the isolation of Actinobacteria-affiliated genera Microbacterium and Kocuria. Based on phylogenetic relatedness and microscopic observations, we hypothesize that the ultrasmall cells in Lake Vida brine are ultramicrocells that are likely in a reduced size state as a result of environmental stress or life cycle-related conditions.

  3. Dependence of CO2-Brine Interfacial Tension on Aquifer Pressure, Temperature and Water Salinity

    Science.gov (United States)

    Bachu, S.; Bennion, B.

    2007-12-01

    Carbon dioxide storage in deep saline aquifers is a climate-change mitigation strategy that has significant potential in the short-to-medium term. The displacement of formation water by CO2 (drainage) and of CO2 by invading aquifer brine (imbibition) depend on the interfacial tension (IFT) of the CO2-brine system. To provide needed data, an extensive laboratory program was conducted for the measurement of the interfacial tension between CO2 and water or brine covering the ranges of 2 to 27 MPa pressure, 20°C to 125°C temperature, and 0 to 334,000 mg/l water salinity. The laboratory experiments were conducted using the pendant drop method combined with the Laplace solution for the profile of the brine drop in the CO2-rich environment. The analysis of the resulting set of 294 IFT measurements reveals that: 1) for conditions of constant temperature and water salinity, IFT decreases steeply with increasing pressure in the range PPc, with an asymptotic trend towards a constant value for high pressures; 2) for the same conditions of constant pressure and temperature, IFT increases with increasing water salinity, reflecting decreasing CO2 solubility in brine as salinity increases; 3) the dependence of IFT on temperature is more complex, depending on the CO2 phase. For TTc, with an asymptotic trend towards a constant value for high temperatures. These results indicate that, in the case of CO2 storage in deep saline aquifers, the formation water displacement by injected CO2 during the injection phase of CO2 storage and the CO2 displacement by invading brine during the CO2 migration phase depend on the in-situ conditions of pressure, temperature and water salinity through the effects that these primary variables have on the IFT between CO2 and aquifer brine. Since the IFT of CO2-brine systems affects relative permeability and capillary pressure, it is essential that the in-situ conditions and their effect of secondary variables are properly taken into account when

  4. An Automatic High Efficient Method for Dish Concentrator Alignment

    Directory of Open Access Journals (Sweden)

    Yong Wang

    2014-01-01

    for the alignment of faceted solar dish concentrator. The isosceles triangle configuration of facet’s footholds determines a fixed relation between light spot displacements and foothold movements, which allows an automatic determination of the amount of adjustments. Tests on a 25 kW Stirling Energy System dish concentrator verify the feasibility, accuracy, and efficiency of our method.

  5. Brine migration resulting from pressure increases in a layered subsurface system

    Science.gov (United States)

    Delfs, Jens-Olaf; Nordbeck, Johannes; Bauer, Sebastian

    2016-04-01

    intermediate aquifer above the injection formation, where brine settles down and flows from the fault zone into the aquifer. This effect changes buoyancy so that lower density brine from the upper aquifers can rise higher and at larger fluxes compared to the case when no intermediary aquifers are present. In general, uplift of brine originating from the intermediary aquifers is mainly restricted to the next overlying two to three permeable aquifers (200m-1000m) or even only to the next aquifer if injection pressures are lower than about 10 bar. If injection induced over-pressures are high, brine from the injection reservoir can dominate inflow into the freshwater reservoir at late times (tens of years). An extensive parameter variation shows the effects of individual parameters. It is found, e.g., that no brine enters the freshwater aquifer if fault permeability is lower than about 10-14 m2. Acknowledgments: This work is part of the ANGUS+ project (www.angusplus.de) and funded by the German Federal Ministry of Education and Research (BMBF) as part of the energy storage initiative "Energiespeicher".

  6. Starch source in high concentrate rations does not affect rumen pH, histamine and lipopolysaccharide concentrations in dairy cows

    NARCIS (Netherlands)

    Pilachai, R.; Schonewille, J.T.; Thamrongyoswittayakul, C.; Aiumlamai, S.; Wachirapakom, C.; Everts, H.; Hendriks, W.H.

    2012-01-01

    The replacement of ground corn by cassava meal on rumen pH, lipopolysaccharide (LPS) and histamine concentrations under typical Thai feeding conditions (high concentrate diets and rice straw as the sole source of roughage) was investigated. Four rumen-fistulated crossbred Holstein, non-pregnant, dry

  7. Cyanobacterial cytotoxicity versus toxicity to brine shrimp Artemia salina.

    Science.gov (United States)

    Hisem, Daniel; Hrouzek, Pavel; Tomek, Petr; Tomšíčková, Jana; Zapomělová, Eliška; Skácelová, Kateřina; Lukešová, Alena; Kopecký, Jiří

    2011-01-01

    Heterocytous cyanobacteria from various habitats were screened for toxicity to brine shrimp Artemia salina and the murine lymphoblastic cell line Sp/2 in order to compare these two testing models for evaluation of risk posed by cyanobacteria to human health. Methanol extracts of biomass and cultivation media were tested for toxicity and selected extracts were fractionated to determine the active fraction. We found a significant toxic effect to A. salina and to Sp/2 cells in 5.2% and 31% of studied extracts, respectively. Only 8.6% of the tested strains were highly toxic to both A. salina and the Sp/2 cell line, and only two of the tested strains were toxic to A. salina and not to the murine cell line. Therefore, it is likely that the toxic effect of cyanobacterial secondary metabolites mostly targets basal metabolic pathways present in mammal cells and so is not manifested in A. salina. We conclude that it is insufficient to monitor cytotoxicity of cyanobacteria using only the brine shrimp bioassay as was usual in the past, since cytotoxicity is a more frequent feature in cyanobacteria in comparison with toxicity to A. salina. A. salina toxicity test should not be used when estimating the possible health risk for humans. We suggest that in vitro mammal cells be used for these purposes.

  8. BELL PEPPER CULTIVATION WITH BRINE FROM BRACKISH WATER DESALINATION

    Directory of Open Access Journals (Sweden)

    CARLOS EDUARDO DE MOURA ARRUDA

    2011-01-01

    Full Text Available In desalination process, besides the potable water, highly salty and pollutant water (brine is generated, which can be used for producing crops since it is carefully monitored. In order to test this hypothesis, bell pepper plants, cv. 'Margarita', were grown in coconut fiber substrate under greenhouse and were irrigated with nutrient solutions prepared with tap water, brine from desalination plant, and its dilution with tap water at 75, 50 and 25%, giving a range of electrical conductivities of the nutrient solution (ECs of 2.6, 3.1, 6.6, 10.0 and 12.2 dS m-1 after the dilutions and fertilizers addition. Completely randomized blocks design was used with 5 treatments (salinity levels of the nutrient solutions and six replications. Leaf area, number of marketable fruit, total and marketable yield were reduced with ECs increase. The marketable yield of bell pepper 'Margarita' reduced 6.3% for each unitary increase of ECs above 2.6 dS m-1 (threshold salinity and the results suggest that in hydroponic system, the reduction of marketable yield with increasing ECs is promoted by reduction of the number of fruits per plant instead of a reduction of fruit mean weight.

  9. RO brine treatment and recovery by biological activated carbon and capacitive deionization process.

    Science.gov (United States)

    Tao, Guihe; Viswanath, Bala; Kekre, Kiran; Lee, Lai Yoke; Ng, How Yong; Ong, Say Leong; Seah, Harry

    2011-01-01

    The generation of brine solutions from dense membrane (reverse osmosis, RO or nanofiltration, NF) water reclamation systems has been increasing worldwide, and the lack of cost effective disposal options is becoming a critical water resources management issue. In Singapore, NEWater is the product of a multiple barrier water reclamation process from secondary treated domestic effluent using MF/UF-RO and UV technologies. The RO brine (concentrates) accounts for more than 20% of the total flow treated. To increase the water recovery and treat the RO brine, a CDI based process with BAC as pretreatment was tested. The results show that ion concentrations in CDI product were low except SiO2 when compared with RO feed water. CDI product was passed through a RO and the RO permeate was of better quality including low SiO2 as compared to NEWater quality. It could be beneficial to use a dedicated RO operated at optimum conditions with better performance to recover the water. BAC was able to achieve 15-27% TOC removal of RO brine. CDI had been tested at a water recovery ranging from 71.6 to 92.3%. CDI based RO brine treatment could improve overall water recovery of NEWater production over 90%. It was found that calcium phosphate scaling and organic fouling was the major cause of CDI pressure increase. Ozone disinfection and sodium bisulfite dosing were able to reduce CDI fouling rate. For sustainable operation of CDI organic fouling control and effective organic fouling cleaning should be further studied.

  10. Chemistry of brines in salt from the Waste Isolation Pilot Plant (WIPP), southeastern New Mexico: a preliminary investigation

    Energy Technology Data Exchange (ETDEWEB)

    Stein, C.L.; Krumhansl, J.L.

    1986-03-01

    We present here analyses of macro- and microscopic (intracrystalline) brines observed within the WIPP facility and in the surrounding halite, with interpretations regarding the origin and history of these fluids and their potential effect(s) on long-term waste storage. During excavation, several large fluid inclusions were recovered from an area of highly recrystallized halite in a thick salt bed at the repository horizon (2150 ft below ground level). In addition, 52 samples of brine ''weeps'' were collected from walls of recently excavated drifts at the same stratigraphic horizon from which the fluid inclusion samples are assumed to have been taken. Analyses of these fluids show that they differ substantially in composition from the inclusion fluids and cannot be explained by mixing of the fluid inclusion populations. Finally, holes in the facility floor that filled with brine were sampled but with no stratographic control; therefore it is not possible to interpret the compositions of these brines with any accuracy, except insofar as they resemble the weep compositions but with greater variation in both K/Mg and Na/Cl ratios. However, the Ca and SO/sub 4/ values for the floor holes are relatively close to the gypsum saturation curve, suggesting that brines filling floor holes have been modified by the presence of gypsum or anhydrite, possibly even originating in one or more of the laterally continuous anhydrite units referred to in the WIPP literature as marker beds. In conclusion, the wide compositional variety of fluids found in the WIPP workings suggest that (1) an interconnected hydrologic system which could effectively transport radonuclides away from the repository does not exist; (2) brine migration studies and experiments must consider the mobility of intergranular fluids as well as those in inclusions; and (3) near- and far-field radionuclide migration testing programs need to consider a wide range of brine compositions rather than a

  11. Impacts of harvesting on brine shrimp (Artemia franciscana) in Great Salt Lake, Utah, USA.

    Science.gov (United States)

    Sura, Shayna A; Belovsky, Gary E

    2016-03-01

    Selective harvesting can cause evolutionary responses in populations via shifts in phenotypic characteristics, especially those affecting life history. Brine shrimp (Artemia franciscana) cysts in Great Salt Lake (GSL), Utah, USA are commercially harvested with techniques that select against floating cysts. This selective pressure could cause evolutionary changes over time. Our objectives are to (1) determine if there is a genetic basis to cyst buoyancy, (2) determine if cyst buoyancy and nauplii mortality have changed over time, and (3) to examine GSL environmental conditions over time to distinguish whether selective harvesting pressure or a trend in environmental conditions caused changes in cyst buoyancy and nauplii mortality. Mating crosses between floating and sinking parental phenotypes with two food concentrations (low and high) indicated there is a genetic basis to cyst buoyancy. Using cysts harvested from 1991-2011, we found cyst buoyancy decreased and nauplii mortality increased over time. Data on water temperature, salinity, and chlorophyll a concentration in GSL from 1994 to 2011 indicated that although water temperature has increased over time and chlorophyll a concentration has decreased over time, the selective harvesting pressure against floating cysts is a better predictor of changes in cyst buoyancy and nauplii mortality over time than trends in environmental conditions. Harvesting of GSL A. franciscana cysts is causing evolutionary changes, which has implications for the sustainable management and harvesting of these cysts. Monitoring phenotypic characteristics and life-history traits of the population should be implemented and appropriate responses taken to reduce the impacts of the selective harvesting.

  12. Bandgap Engineering in High-Efficiency Multijunction Concentrator Cells

    Energy Technology Data Exchange (ETDEWEB)

    King, R. R.; Sherif, R. A.; Kinsey, G. S.; Kurtz, S.; Fetzer, C. M.; Edmondson, K. M.; Law, D. C.; Cotal, H. L.; Krut, D. D.; Ermer, J. H.; Karam, N. H.

    2005-08-01

    This paper discusses semiconductor device research paths under investigation with the aim of reaching the milestone efficiency of 40%. A cost analysis shows that achieving very high cell efficiencies is crucial for the realization of cost-effective photovoltaics, because of the strongly leveraging effect of efficiency on module packaging and balance-of systems costs. Lattice-matched (LM) GaInP/ GaInAs/ Ge 3-junction cells have achieved the highest independently confirmed efficiency at 175 suns, 25?C, of 37.3% under the standard AM1.5D, low-AOD terrestrial spectrum. Lattice-mismatched, or metamorphic (MM), materials offer still higher potential efficiencies, if the crystal quality can be maintained. Theoretical efficiencies well over 50% are possible for a MM GaInP/ 1.17-eV GaInAs/ Ge 3-junction cell limited by radiative recombination at 500 suns. The bandgap - open circuit voltage offset, (Eg/q) - Voc, is used as a valuable theoretical and experimental tool to characterize multijunction cells with subcell bandgaps ranging from 0.7 to 2.1 eV. Experimental results are presented for prototype 6-junction cells employing an active {approx}1.1-eV dilute nitride GaInNAs subcell, with active-area efficiency greater than 23% and over 5.3 V open-circuit voltage under the 1-sun AM0 space spectrum. Such cell designs have theoretical efficiencies under the terrestrial spectrum at 500 suns concentration exceeding 55% efficiency, even for lattice-matched designs.

  13. LPWCO method for the treatment of high concentrated organic wastewater

    Institute of Scientific and Technical Information of China (English)

    1998-01-01

    Based on wet air oxidation (WAO) and Fenton reagent, thispaper raises a new low pressure wet catalytic oxidation(LPWCO)which requires low pressure for the treatment of highlyconcentrated and refractory organic wastewater. Compared withgeneral wet air oxidation, the pressure of the treatment(0.1-0.6MPa) is only one of tens to percentage of latter(3.5-10MPa). Inaddition, its temperature is no more than 180℃.Compared withFenton reagent, while H2O2/COD(weight ratio) less than 1.2, theremoval of COD in the treatment is over twenty percents more thanFenton's even the value of COD is more than 14000mg/L. In thispaper, we study the effect factor of COD removal and the mechanismof this treatment. The existence of synergistic effect (catalytic oxidation and carbonization) for COD removal in H2SO4-Fenton reagent system under the condition of applied pressure and heating (0.1-0.6MPa, 104-165℃) was verified. The best condition of this disposal are as follows:H2O2/COD(weight ratio)=0.2-1.0, Fe2+ 0.6×10-3 mol, H2SO4 0.5mol, COD>1×104mg/L, the operating pressure is 0.1-0.6MPa and temperature is 104-165℃. This method suit to dispose the high-concentrated refractory wastewater, especially to the wastewater containing H2SO produced in the manufacture of pesticide, dyestuff and petrochemical works.

  14. High Oxygen Concentrations Adversely Affect the Performance of Pulmonary Surfactant.

    Science.gov (United States)

    Smallwood, Craig D; Boloori-Zadeh, Parnian; Silva, Maricris R; Gouldstone, Andrew

    2017-08-01

    Although effective in the neonatal population, exogenous pulmonary surfactant has not demonstrated a benefit in pediatric and adult subjects with hypoxic lung injury despite a sound physiologic rationale. Importantly, neonatal surfactant replacement therapy is administered in conjunction with low fractional FIO2 while pediatric/adult therapy is administered with high FIO2 . We suspected a connection between FIO2 and surfactant performance. Therefore, we sought to assess a possible mechanism by which the activity of pulmonary surfactant is adversely affected by direct oxygen exposure in in vitro experiments. The mechanical performance of pulmonary surfactant was evaluated using 2 methods. First, Langmuir-Wilhelmy balance was utilized to study the reduction in surface area (δA) of surfactant to achieve a low bound value of surface tension after repeated compression and expansion cycles. Second, dynamic light scattering was utilized to measure the size of pulmonary surfactant particles in aqueous suspension. For both experiments, comparisons were made between surfactant exposed to 21% and 100% oxygen. The δA of surfactant was 21.1 ± 2.0% and 35.8 ± 2.0% during exposure to 21% and 100% oxygen, respectively (P = .02). Furthermore, dynamic light-scattering experiments revealed a micelle diameter of 336.0 ± 12.5 μm and 280.2 ± 11.0 μm in 21% and 100% oxygen, respectively (P < .001), corresponding to a ∼16% decrease in micelle diameter following exposure to 100% oxygen. The characteristics of pulmonary surfactant were adversely affected by short-term exposure to oxygen. Specifically, surface tension studies revealed that short-term exposure of surfactant film to high concentrations of oxygen expedited the frangibility of pulmonary surfactant, as shown with the δA. This suggests that reductions in pulmonary compliance and associated adverse effects could begin to take effect in a very short period of time. If these findings can be demonstrated in vivo, a role for

  15. Partition behavior of virgin olive oil phenolic compounds in oil-brine mixtures during thermal processing for fish canning.

    Science.gov (United States)

    Sacchi, Raffaele; Paduano, Antonello; Fiore, Francesca; Della Medaglia, Dorotea; Ambrosino, Maria Luisa; Medina, Isabel

    2002-05-08

    The chemical modifications and partitioning toward the brine phase (5% salt) of major phenol compounds of extra virgin olive oil (EVOO) were studied in a model system formed by sealed cans filled with oil-brine mixtures (5:1, v/v) simulating canned-in-oil food systems. Filled cans were processed in an industrial plant using two sterilization conditions commonly used during fish canning. The partitioning of phenolic compounds toward brine induced by thermal processing was studied by reversed-phase high-performance liquid chromatographic analysis of the phenol fraction extracted from oils and brine. Hydroxytyrosol (1), tyrosol (2), and the complex phenolic compounds containing 1 and 2 (i.e., the dialdehydic form of decarboxymethyl oleuropein aglycon 3, the dialdehydic form of decarboxymethyl ligstroside aglycon 4, and the oleuropein aglycon 6) decreased in the oily phase after sterilization with a marked partitioning toward the brine phase. The increase of the total amount of 1 and 2 after processing, as well as the presence of elenolic acid 7 released in brine, revealed the hydrolysis of the ester bond of hydrolyzable phenolic compounds 3, 4, and 6 during thermal processing. Both phenomena (partitioning toward the water phase and hydrolysis) contribute to explain the loss of phenolic compounds exhibited by EVOO used as filling medium in canned foods, as well as the protection of n-3 polyunsaturated fatty acids in canned-in-EVOO fish products.

  16. Nature and origin of RSL: Spectroscopy and detectability of liquid brines in the near-infrared

    Science.gov (United States)

    Masse, Marion; Beck, Pierre; Schmitt, Bernard; Pommerol, Antoine; McEwen, Alfred; Chevrier, Vincent; Brissaud, Olivier

    2013-04-01

    If water has likely flowed on Mars in its early history, the current presence of liquid water is debatable. However, some recently discovered fea-tures named "Recurrent Slope Lineae" (RSL) suggest that superficial liquid can occur on present day Mars in a transient state [McEwen et al., 2011]. RSL are dark (up to 40% darker than the surrounding areas), narrow (0.5-5 m) and are mostly found in the southern mid-latitudes. Repeated MRO/HiRISE images reveal that they appear and grow during warm seasons and fade and disappear during cold seasons. They develop on steep slopes (25°-40°), favoring equator-facing slopes, times and places with peak temperatures of ~250-300K. The most likely formation process of RSL involves the presence of liquid brines near the surface. Brines are more stable on Mars than pure water [e.g. Chevrier et al., 2009] because salts can depress the freezing point of water by up to 70 K. However, this hypothesis suffers from the lack of clear identification of brines with the high resolution CRISM spectra. The mineralogical characterization of RSL is challenging because RSL are much smaller than the ~18 m pixel scale of CRISM data but spectral features diagnostic of water or brines [Hanley et al., 2010] are not observable even on the largest RSL. The goal of our study is to reproduce with laboratory experiments some hydration and dehydration cycles of different kind of brines mixed with basaltic soil. These experiments aim to understand the spectroscopic behavior of brines during these processes and to determine the diagnostic spectral features that we can expected to find for Martian RSL. We found that, if the surface displays a low albedo from the beginning of the hydration to the end of the dehydration, diagnostic brines absorption bands are only observed when the liquid film is formed. This is consistent with our current RSL observations. In the future, we need to acquire some new CRISM data when the formation of liquid brines is the most

  17. High-Efficiency Organic Solar Concentrators for Photovoltaics

    National Research Council Canada - National Science Library

    Michael J. Currie; Jonathan K. Mapel; Timothy D. Heidel; Shalom Goffri; Marc A. Baldo

    2008-01-01

    The cost of photovoltaic power can be reduced with organic solar concentrators. These are planar waveguides with a thin-film organic coating on the face and inorganic solar cells attached to the edges...

  18. In-situ fracture mapping using geotomography and brine tracers

    Energy Technology Data Exchange (ETDEWEB)

    Deadrick, F.J.; Ramirez, A.L.; Lytle, R.J.

    1981-01-01

    The Lawrence Livermore National Laboratory is currently assessing the capabilities of high resolution geophysical methods to characterize geologic sites for the disposal of high level nuclear waste. A successful experiment has recently been performed in which salt water tracers and high frequency electromagnetic waves were utilized to map rock mass fracture zones in-situ. Multiple cross-borehole EM transmissions were used to generate a tomographic image of the fractured rock region between two boreholes. The tomographs obtained correlate well with conventional wireline geophysical logs which can be used to infer the location of fractured zones in the rock mass. This indirect data suggests that the geotomography and brine tracer technique may have merit in mapping fractured zones between boreholes.

  19. Models of Geothermal Brine Chemistry

    Energy Technology Data Exchange (ETDEWEB)

    Nancy Moller Weare; John H. Weare

    2002-03-29

    Many significant expenses encountered by the geothermal energy industry are related to chemical effects. When the composition, temperature of pressure of the fluids in the geological formation are changed, during reservoir evolution, well production, energy extraction or injection processes, the fluids that were originally at equilibrium with the formation minerals come to a new equilibrium composition, temperature and pressure. As a result, solid material can be precipitated, dissolved gases released and/or heat lost. Most geothermal energy operations experience these phenomena. For some resources, they create only minor problems. For others, they can have serious results, such as major scaling or corrosion of wells and plant equipment, reservoir permeability losses and toxic gas emission, that can significantly increase the costs of energy production and sometimes lead to site abandonment. In future operations that exploit deep heat sources and low permeability reservoirs, new chemical problems involving very high T, P rock/water interactions and unknown injection effects will arise.

  20. Development of manufacturing capability for high-concentration, high-efficiency silicon solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Sinton, R.A.; Verlinden, P.J.; Crane, R.A.; Swanson, R.N. [SunPower Corp., Sunnyvale, CA (United States)

    1996-10-01

    This report presents a summary of the major results from a program to develop a manufacturable, high-efficiency silicon concentrator solar cell and a cost-effective manufacturing facility. The program was jointly funded by the Electric Power Research Institute, Sandia National Laboratories through the Concentrator Initiative, and SunPower Corporation. The key achievements of the program include the demonstration of 26%-efficient silicon concentrator solar cells with design-point (20 W/cm{sup 2}) efficiencies over 25%. High-performance front-surface passivations; that were developed to achieve this result were verified to be absolutely stable against degradation by 475 days of field exposure at twice the design concentration. SunPower demonstrated pilot production of more than 1500 of these cells. This cell technology was also applied to pilot production to supply 7000 17.7-cm{sup 2} one-sun cells (3500 yielded wafers) that demonstrated exceptional quality control. The average efficiency of 21.3% for these cells approaches the peak efficiency ever demonstrated for a single small laboratory cell within 2% (absolute). Extensive cost models were developed through this program and calibrated by the pilot-production project. The production levels achieved indicate that SunPower could produce 7-10 MW of concentrator cells per year in the current facility based upon the cell performance demonstrated during the program.

  1. Highly Sensitive Cadmium Concentration Sensor Using Long Period Grating

    Directory of Open Access Journals (Sweden)

    A. S. Lalasangi

    2011-08-01

    Full Text Available In this paper we have proposed a simple and effective Long Period Grating chemical sensor for detecting the traces of Cadmium (Cd++ in drinking water at ppm level. Long Period gratings (LPG were fabricated by point-by-point technique with CO2 laser. We have characterized the LPG concentration sensor sensitivity for different solutions of Cd concentrations varying from 0.01 ppm to 0.04 ppm by injecting white Light source and observed transmitted spectra using Optical Spectrum Analyzer (OSA. Proper reagents have been used in the solutions for detection of the Cd species. The overall shift in wavelength is 10 nm when surrounding medium gradually changed from water to 0.04 ppm of cadmium concentrations. A comparative study has been done using sophisticated spectroscopic atomic absorption spectrometer (AAS and Inductively Coupled Plasma (ICP instruments. The spectral sensitivity enhancement was done by modifying grating surface with gold nanoparticles.

  2. Methods and devices for high-throughput dielectrophoretic concentration

    Energy Technology Data Exchange (ETDEWEB)

    Simmons, Blake A. (San Francisco, CA); Cummings, Eric B. (Livermore, CA); Fiechtner, Gregory J. (Germantown, MD); Fintschenko, Yolanda (Livermore, CA); McGraw, Gregory J. (Ann Arbor, MI); Salmi, Allen (Escalon, CA)

    2010-02-23

    Disclosed herein are methods and devices for assaying and concentrating analytes in a fluid sample using dielectrophoresis. As disclosed, the methods and devices utilize substrates having a plurality of pores through which analytes can be selectively prevented from passing, or inhibited, on application of an appropriate electric field waveform. The pores of the substrate produce nonuniform electric field having local extrema located near the pores. These nonuniform fields drive dielectrophoresis, which produces the inhibition. Arrangements of electrodes and porous substrates support continuous, bulk, multi-dimensional, and staged selective concentration.

  3. Methods and devices for high-throughput dielectrophoretic concentration

    Science.gov (United States)

    Simmons, Blake A.; Cummings, Eric B.; Fiechtner, Gregory J.; Fintschenko, Yolanda; McGraw, Gregory J.; Salmi, Allen

    2010-02-23

    Disclosed herein are methods and devices for assaying and concentrating analytes in a fluid sample using dielectrophoresis. As disclosed, the methods and devices utilize substrates having a plurality of pores through which analytes can be selectively prevented from passing, or inhibited, on application of an appropriate electric field waveform. The pores of the substrate produce nonuniform electric field having local extrema located near the pores. These nonuniform fields drive dielectrophoresis, which produces the inhibition. Arrangements of electrodes and porous substrates support continuous, bulk, multi-dimensional, and staged selective concentration.

  4. Generation of porphyry copper deposits by gas-brine reaction in volcanic arcs

    Science.gov (United States)

    Blundy, J.; Mavrogenes, J.; Tattitch, B.; Sparks, S.; Gilmer, A.

    2015-03-01

    Porphyry copper deposits, that is, copper ore associated with hydrothermal fluids rising from a magma chamber, supply 75% of the world's copper. They are typically associated with intrusions of magma in the crust above subduction zones, indicating a primary role for magmatism in driving mineralization. However, it is not clear that a single, copper-rich magmatic fluid could trigger both copper enrichment and the subsequent precipitation of sulphide ore minerals within a zone of hydrothermally altered rock. Here we draw on observations of modern subduction zone volcanism to propose an alternative process for porphyry copper formation. We suggest that copper enrichment initially involves metalliferous, magmatic hyper-saline liquids, or brines, that exsolve from large, magmatic intrusions assembled in the shallow crust over tens to hundreds of thousands of years. In a subsequent step, sulphide ore precipitation is triggered by the interaction of the accumulated brines with sulphur-rich gases, liberated in short-lived bursts from the underlying mafic magmas. We use high-temperature and high-pressure laboratory experiments to simulate such gas-brine interactions. The experiments yield copper-iron sulphide minerals and hydrogen chloride gas at magmatic temperatures of 700-800 °C, with textural and chemical characteristics that resemble those in porphyry copper deposits. We therefore conclude that porphyry copper ore forms in a two-stage process of brine enrichment followed by gas-induced precipitation.

  5. Effects of NaCl on Fermentative Metabolism of Mature Green Tomatoes cv. Ailsa Craig in Brine

    Directory of Open Access Journals (Sweden)

    Sotirios Fragkostefanakis

    2010-01-01

    Full Text Available The effect of osmotic strength on gene expression and activity of the major enzymes of fermentative metabolism of mature green tomato fruit (Solanum lycopersicum cv. Ailsa Craig has been studied by exposing fruit to brine containing 0 (water, 5 and 10 % NaCl. The fruits were surface sterilized prior to treatment to prevent the growth of microbes naturally present on the skin of the fruit. Changes in fruit expression of fermentation genes and the activity of the respective enzymes as well as physicochemical quality characteristics (soluble solid content, titratable acidity, pH and firmness were studied in both fruit and brine for 0.5, 1, 1.5, 2, 3, 7 and 14 days. Discrepancies in responses that resulted from the different salt concentrations were obtained at molecular and quality levels. The complex kinetics of solutes between the fruit and the surrounding solution due to osmotic potential has led to different responses of the tissue to fermentation. Tomato fruit showed cracking soon after storage in water; water-stored fruit had higher titratable acidity, lower soluble solid content, and higher induction of anaerobic metabolism as indicated by the expression or the activity of the fermentation enzymes compared to fruit stored in brine with 5 or 10 % NaCl. No cracking was observed in fruit stored in 5 (isotonic or 10 % NaCl (hypertonic brine, though in the latter, signs of dehydration were observed. The presence of salt in brine reduced the intensity of fermentative metabolism as indicated by the lower gene expression and enzyme activity. However, fruit stored in brine with 5 % NaCl survived longer than with 0 or 10 % NaCl. The presence of 5 % NaCl in brine caused mild changes of both the fermentative metabolism and the physicochemical characteristics and prevented fruit deterioration during storage.

  6. Ice Control with Brine on Highways

    DEFF Research Database (Denmark)

    Bolet, Lars

    meant that six salt barns could be phased out. This made it possible to revise the staff's duty roster and thus meet the rest hour demands raised by the health and safety at work acts. Successful pre-salting is, of course, dependent on reliable weather forecasts and on staff well trained in the art...... traffic flow the spread rate of pure sodium chloride (and thus the environmental impact) in the pre-salting operations was cut back by more than one third. Compared to neighbouring counties the use of salt is less than fifty percent per square meter. In addition, supply of brine from two mixer-plants...

  7. Toxigenicity of enniatins from Western Australian Fusarium species to brine shrimp (Artemia franciscana).

    Science.gov (United States)

    Tan, Diana C; Flematti, Gavin R; Ghisalberti, Emilio L; Sivasithamparam, Krishnapillai; Barbetti, Martin J

    2011-04-01

    The high prevalence (14 of 24 isolates) of enniatin-producing isolates from Western Australian Fusarium species isolated from pasture legumes associated with sheep feed refusal and rat deaths, and the high toxicity of their crude extracts to brine shrimp (Artemia franciscana) from a previous study warranted further investigation of this class of mycotoxin. Crude extracts from Fusarium acuminatum, Fusarium avenaceum, Fusarium tricinctum and Fusarium sambucinum, along with enniatins A, A1, B and B1 purified from a Western Australian strain of F. acuminatum using semi-preparative HPLC, were bioassayed using brine shrimp. All Fusarium isolates produced both enniatins B and B1, except for F. tricinctum WAC 8019, and 11 of the 17 isolates produced enniatin A1. Overall, all of the F. avenaceum isolates produced high amounts of enniatins, in particular enniatin B. One isolate of F. acuminatum (WAC 5715) and of F. tricinctum (WAC 11486) also produced high amounts of both enniatins B and B1. Only F. acuminatum WAC 5715 produced enniatin A among the tested isolates. All four purified enniatins A, A1, B, B1, individually and in combination, caused brine shrimp toxicity after 6 h of exposure, implicating that this emerging class of mycotoxin as a cause of the acute toxicity to brine shrimp observed. The mixture of all four enniatins was the most toxic to brine shrimp compared to purified individual enniatins, where the relative toxicity order was B > B1 > A1 > A. Enniatin B was the individual most toxic enniatin with some bioactivity at 5 μg/mL and almost 100% brine shrimp death at 50 μg/mL after 24 h of exposure. This study is the first report to confirm the acute toxicity of enniatins A, A1, B and B1 to brine shrimp, and also highlights the need for further investigation of the potential toxicity of these cyclic hexadepsipeptides to animals and humans.

  8. High Quantum Efficiency and High Concentration Erbium-Doped Silica Glasses Fabricated by Sintering Nanoporous Glasses

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    A new method was used to prepare erbium-doped high silica (SiO2%>96%) glasses by sintering nanoporous glasses. The concentration of erbium ions in high silica glasses can be considerably more than that in silica glasses prepared by using conventional methods. The fluorescence of 1532 nm has an FWHM (Full Wave at Half Maximum) of 50 nm, wider than 35 nm of EDSFA (erbium-doped silica fiber amplifer), and hence the glass possesses potential application in broadband fiber amplifiers. The Judd-Ofelt theoretical analysis reflects that the quantum efficiency of this erbium-doped glass is about 0.78, although the erbium concentration in this glass (6×103) is about twenty times higher than that in silica glass. These excellent characteristics of Er-doped high silica glass will be conducive to its usage in optical amplifiers and microchip lasers.

  9. Interactive effect of selenium and mercury on development and mortality of brine shrimp, Artemia sp.

    Energy Technology Data Exchange (ETDEWEB)

    Forsythe, B.L. II; Bailey, F.C.; Klaine, S.J. [Clemson Univ., Pendleton, SC (United States)

    1994-12-31

    The interactions between organic mercury and selenium derivatives are well documented. Inorganic mercury has been shown to have a deleterious effect on the development of brine shrimp, Artemia franciscana while selenate has no effect. In this study, concentrations as low as 0.1 mg/l Hg (as Hg(NO{sub 3})2) slowed the rate of development. Selenate concentrations ranging from 0.1 to 5.0 mg/l as Se decreased the effect of Hg on brine shrimp developmental rate. Both selenate and inorganic mercury alone produced a dose-response with respect to nauplii mortality. Preliminary data suggest that combinations of selenate and inorganic mercury act antagonistically to lower this mortality.

  10. Generation of porphyry copper deposits by gas-brine reaction in volcanic arcs

    Science.gov (United States)

    Blundy, Jon; Mavrogenes, John; Tattitch, Brian; Sparks, Steve; Gilmer, Amy

    2014-05-01

    Porphyry copper deposits (PCDs) are characterised by a close spatial and temporal association with small, hypabyssal intrusions of silicic magmas in volcanic arcs. PCD formation requires elevated chlorine and water to concentrate copper in magmatic hypersaline liquids (or brines), and elevated sulphur to precipitate copper-rich sulphides. These twin requirements are hard to reconcile with experimental and petrological evidence that voluminous chlorine-rich, hydrous silicic magmas, of the variety favourable to copper enrichment, lack sufficient sulphur to precipitate directly the requisite quantities of sulphides. These features are, however, consistent with observations of active volcanic arcs whereby PCDs can be viewed as roots of dome volcanoes above shallow reservoirs where silicic magmas accumulate over long time spans. During protracted periods of dormancy metal-enriched dense brines accumulate in and above the silicic reservoir through slow, low-pressure degassing. Meanwhile cogenetic volatile-rich mafic magmas and their exsolved, sulphur and CO2-rich fluids accumulate in deeper reservoirs. Periodic destabilisation of these reservoirs leads to short-lived bursts of volcanism liberating sulphurous gases, which react with the shallow-stored brines to form copper-rich sulphides and acidic vapours. We test this hypothesis with a novel set of 'porphyry in a capsule' experiments designed to simulate low-pressure (1-2 kbar) interaction of basalt-derived, sulphur-rich gases with brine-saturated, copper-bearing, but sulphur-free, granite. Experiments were run at 720-850 ° C in cold-seal apparatus with basaltic andesite, loaded with H2O and S, situated below dacite, loaded with H2O, Cl and Cu. At run conditions both compositions are substantially degassed and crystallized. S-rich gas from the basaltic andesite ascends to react with Cu-rich brines exsolved from the dacite, Our experiments reveal the direct precipitation of copper-sulphide minerals, in vugs and veins

  11. Photocatalytic reduction of nitrate using titanium dioxide for regeneration of ion exchange brine

    OpenAIRE

    Yang,Ting; Doudrick, Kyle; Westerhoff, Paul

    2012-01-01

    Nitrate is often removed from groundwater by ion exchange (IX) before its use as drinking water. Accumulation of nitrate in IX brine reduces the efficiency of IX regeneration and the useful life of the regeneration brine. For the first time, we present a strategy to photocatalytically reduce nitrate in IX brine, thereby extending the use of the brine. Titanium dioxide (Evonik P90), acting as photocatalyst, reduced nitrate effectively in both synthetic brines and sulfate-removed IX brine when ...

  12. Review of the impacts of leaking CO 2 gas and brine on groundwater quality

    Energy Technology Data Exchange (ETDEWEB)

    Qafoku, Nikolla P.; Lawter, Amanda R.; Bacon, Diana H.; Zheng, Liange; Kyle, Jennifer; Brown, Christopher F.

    2017-06-01

    This review paper provides a synthetic view of the existing knowledge and summarizes data and findings of the recent literature on the subject of the potential leaking of CO2 from the deep subsurface storage reservoirs and the effects on aquifer quality. New ideas and concepts are developed and insights are also provided. The objectives of this paper are to: 1) present and discuss potential risks for groundwater degradation due to CO2 gas and brine exposure; 2) identify the set of geochemical data required to assess and predict aquifer responses to CO2 and brine leakage. Specifically, this paper will discuss the following issues: 1) Aquifer responses (such as changes in aqueous phase/groundwater chemical composition; changes in solid phase chemistry and mineralogy; changes in the extent and rate of reactions and processes and possible establishment of a new network of reactions and processes affecting or controlling overall mobility of major, minor, and trace elements; development of conceptual and reduced order models (ROMs) to describe and predict aquifer responses); 2) The degree of impact such as significant or insignificant changes in pH and major, minor, and trace element release that depend on the following controlling variables; the effect of leaking plume characteristics (gas composition, pure CO2 and/or CO2 -CH4 -H2S mixtures and brine concentration and composition (trace metals); aquifer properties [such as initial aqueous phase conditions and mineralogy: minerals controlling sediments’ response (e.g., calcite, Si bearing minerals, etc.)]; overview of relevant hydrogeological and geochemical processes related to the impact of CO2 gas and brine on groundwater quality; the fate of the elements released from sediments or transported with brine (such as precipitation/incorporation into minerals (calcite and other minerals), adsorption, electron transfer reactions, the role of natural attenuation; whether or not the release of metals following exposure to

  13. The effect of brine on the creep behaviour and dissolution chemistry of evaporites

    National Research Council Canada - National Science Library

    Souza, E De; Lee, R

    1998-01-01

    To evaluate operational problems in evaporite deposit utilization associated with brine, halite, sylvinite, and carnallitic ore were creep tested under unconfined conditions, both with and without added brine...

  14. Concentration measurement of yeast suspensions using high frequency ultrasound backscattering.

    Science.gov (United States)

    Elvira, Luis; Vera, Pedro; Cañadas, Francisco Jesús; Shukla, Shiva Kant; Montero, Francisco

    2016-01-01

    This work proposes the use of an ultrasound based technique to measure the concentration of yeasts in liquid suspension. This measurement was achieved by the detection and quantification of ultrasonic echoes backscattered by the cells. More specifically, the technique was applied to the detection and quantification of Saccharomyces cerevisiae. A theoretical approach was proposed to get the average density and sound speed of the yeasts, which were found to be 1116 kg/m(3) and 1679 m/s, respectively. These parameters were needed to model the waves backscattered by each single cell. A pulse-echo arrangement working around 50 MHz, being able to detect echoes from single yeasts was used to characterize experimentally yeast solutions from 10(2) to 10(7)cells/ml. The Non-negative Matrix Factorization denoising technique was applied for data analysis. This technique required a previous learning of the spectral patterns of the echoes reflected from yeasts in solution and the base noise from the liquid medium. Comparison between pulse correlation (without denoising) and theoretical and experimental pattern learning was made to select the best signal processing. A linear relation between ultrasound output and concentration was obtained with correlation coefficient R(2)=0.996 for the experimental learning. Concentrations from 10(4) to 10(7)cells/ml were detected above the base noise. These results show the viability of using the ultrasound backscattering technique to detect yeasts and measure their concentration in liquid cultures, improving the sensitivity obtained using spectrophotometric methods by one order of magnitude.

  15. Dimerization in Highly Concentrated Solutions of Phosphoimidazolide Activated Monomucleotides

    Science.gov (United States)

    Kanavarioti, Anastassia

    1997-08-01

    Phosphoimidazolide activated ribomononucleotides (*pN) are useful substrates for the non-enzymatic synthesis of polynucleotides. However, dilute neutral aqueous solutions of *pN typically yield small amounts of dimers and traces of polymers; most of *pN hydrolyzes to yield nucleoside 5'-monophosphate. Here we report the self-condensation of nucleoside 5'-phosphate 2-methylimidazolide (2-MeImpN with N = cytidine, uridine or guanosine) in the presence of Mg2+ in concentrated solutions, such as might have been found in an evaporating lagoon on prebiotic Earth. The product distribution indicates that oligomerization is favored at the expense of hydrolysis. At 1.0 M, 2-MeImpU and 2-MeImpC produce about 65% of oligomers including 4% of the 3',5'-linked dimer. Examination of the product distribution of the three isomeric dimers in a self-condensation allows identification of reaction pathways that lead to dimer formation. Condensations in a concentrated mixture of all three nucleotides (U,C,G mixtures) is made possible by the enhanced solubility of 2-MeImpG in such mixtures. Although percent yield of internucleotide linked dimers is enhanced as a function of initial monomer concentration, pyrophosphate dimer yields remain practically unchanged at about 20% for 2-MeImpU, 16% for 2-MeImpC and 25% of the total pyrophosphate in the U,C,G mixtures. The efficiency by which oligomers are produced in these concentrated solutions makes the evaporating lagoon scenario a potentially interesting medium for the prebiotic synthesis of dimers and short RNAs.

  16. Haloanaerobium kushneri sp. nov., an obligately halophilic, anaerobic bacterium from an oil brine

    Science.gov (United States)

    Bhupathiraju, V. K.; McInerney, M. J.; Woese, C. R.; Tanner, R. S.

    1999-01-01

    Three strains, designated VS-751T, VS-511 and VS-732, of a strictly anaerobic, moderately halophilic, Gram-negative, rod-shaped bacterium were isolated from a highly saline (15-20%) brine from an oil reservoir in central Oklahoma, USA. The optimal concentration of NaCl for growth of these three strains was 2 M (12%), and the strains also grew in the presence of an additional 1 M MgCl2. The strains were mesophilic and grew at a pH range of 6-8. Carbohydrates used by all three strains included glucose, fructose, arabinose, galactose, maltose, mannose, cellobiose, sucrose and inulin. Glucose fermentation products included ethanol, acetate, H2 and CO2, with formate produced by two of the three strains. Differences were noted among strains in the optimal temperature and pH for growth, the maximum and minimum NaCl concentration that supported growth, substrate utilization and cellular fatty acid composition. Despite the phenotypic differences among the three strains, analysis of the 16S rRNA gene sequences and DNA-DNA hybridizations showed that these three strains were members of the same genospecies which belonged to the genus Haloanaerobium. The phenotypic and genotypic characteristics of strains VS-751T, VS-511 and VS-732 are different from those of previously described species of Haloanaerobium. It is proposed that strain VS-751T (ATCC 700103T) be established as the type strain of a new species, Haloanaerobium kushneri.

  17. High concentrations of pepsin in bronchoalveolar lavage fluid from children with cystic fibrosis are associated with high interleukin-8 concentrations.

    LENUS (Irish Health Repository)

    McNally, P

    2012-02-01

    BACKGROUND: Gastro-oesophageal reflux is common in children with cystic fibrosis (CF) and is thought to be associated with pulmonary aspiration of gastric contents. The measurement of pepsin in bronchoalveolar lavage (BAL) fluid has recently been suggested to be a reliable indicator of aspiration. The prevalence of pulmonary aspiration in a group of children with CF was assessed and its association with lung inflammation investigated. METHODS: This was a cross-sectional case-control study. BAL fluid was collected from individuals with CF (n=31) and healthy controls (n=7). Interleukin-8 (IL-8), pepsin, neutrophil numbers and neutrophil elastase activity levels were measured in all samples. Clinical, microbiological and lung function data were collected from medical notes. RESULTS: The pepsin concentration in BAL fluid was higher in the CF group than in controls (mean (SD) 24.4 (27.4) ng\\/ml vs 4.3 (4.0) ng\\/ml, p=0.03). Those with CF who had raised pepsin concentrations had higher levels of IL-8 in the BAL fluid than those with a concentration comparable to controls (3.7 (2.7) ng\\/ml vs 1.4 (0.9) ng\\/ml, p=0.004). Within the CF group there was a moderate positive correlation between pepsin concentration and IL-8 in BAL fluid (r=0.48, p=0.04). There was no association between BAL fluid pepsin concentrations and age, sex, body mass index z score, forced expiratory volume in 1 s or Pseudomonas aeruginosa colonisation status. CONCLUSIONS: Many children with CF have increased levels of pepsin in the BAL fluid compared with normal controls. Increased pepsin levels were associated with higher IL-8 concentrations in BAL fluid. These data suggest that aspiration of gastric contents occurs in a subset of patients with CF and is associated with more pronounced lung inflammation.

  18. Design of the Brine Evaporation Bag for Increased Water Recovery in Microgravity

    Science.gov (United States)

    Hayden, Anna L.; Delzeit, Lance D.

    2015-01-01

    The existing water recovery system on the International Space Station (ISS) is limited to 75% reclamation; consequently, long duration space missions are currently unfeasible due to the large quantity of water necessary to sustain the crew. The Brine Evaporation Bag (BEB) is a proposed system to supplement the existing water recovery system aboard the ISS that can to increase water recovery to 99%. The largest barrier to high water recovery is mineral scaling inside the water recovery equipment, which leads to equipment failure; therefore, some water must remain to keep the minerals dissolved. This waste stream is liquid brine containing salts, acids, organics, and water. The BEB is designed to recover this remaining water while protecting the equipment from scale. The BEB consists of a sealed bag containing a hydrophobic membrane that allows water vapor and gas to pass through. It is operated under vacuum, heated, and continuously filled with brine to boil away the water. The water vapor is recovered and the solids are contained inside the bag for disposal. The BEB can dry the brine to a solid block. Ongoing work includes improving the design of the BEB and the evaporator to prevent leaks, maximize the rate of water removal, and minimize energy use and weight. Additional testing will determine whether designs are heat- or mass-transfer limited and the optimal water recovery rate.

  19. Long-Term Corrosion Potential Behavior of Alloy 22 in Hot 5 m CaCl2 + 5 m Ca(NO3)2 Brines

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez, M A; Carranza, R M; Stuart, M L; Rebak, R B

    2007-02-20

    Alloy 22 is a nickel base alloy highly resistant to all forms of corrosion. In very aggressive conditions (e.g. hot concentrated chloride containing brines) Alloy 22 could suffer localized attack, namely pitting and crevice corrosion. The occurrence of localized corrosion in a given environment is governed by the values of the critical potential (E{sub crit}) for crevice corrosion and the corrosion potential (E{sub corr}) that the alloy may establish in the studied environment. If E{sub corr} is equal or higher than E{sub crit}, localized corrosion may be expected. This paper discusses the evolution of E{sub corr} of Alloy 22 specimens in 5 m CaCl{sub 2} + 5 m Ca(NO{sub 3}){sub 2} brines at 100 C and 120 C. Two types of specimens were used, polished as-welded (ASW) creviced and noncreviced specimens and as-welded plus solution heat-treated (ASW+SHT) creviced specimens. The latter contained the black annealing oxide film on the surface. Results show that, for all types of Alloy 22 specimens the E{sub corr} was higher at 120 C than at 100 C, probably because a more protective film formed at the higher temperature. Specimens with the black oxide film on the surface showed more oscillations in the potential. None of the tested specimens suffered crevice corrosion probably because of the relatively high concentration of nitrate in the electrolyte, R = [NO3]/[Cl] = 1.

  20. High pressure inertial focusing for separating and concentrating bacteria at high throughput

    Science.gov (United States)

    Cruz, J.; Hooshmand Zadeh, S.; Graells, T.; Andersson, M.; Malmström, J.; Wu, Z. G.; Hjort, K.

    2017-08-01

    Inertial focusing is a promising microfluidic technology for concentration and separation of particles by size. However, there is a strong correlation of increased pressure with decreased particle size. Theory and experimental results for larger particles were used to scale down the phenomenon and find the conditions that focus 1 µm particles. High pressure experiments in robust glass chips were used to demonstrate the alignment. We show how the technique works for 1 µm spherical polystyrene particles and for Escherichia coli, not being harmful for the bacteria at 50 µl min-1. The potential to focus bacteria, simplicity of use and high throughput make this technology interesting for healthcare applications, where concentration and purification of a sample may be required as an initial step.

  1. Natural heat storage in a brine-filled solar pond in the Tully Valley of central New York

    Science.gov (United States)

    Hayhurst, Brett; Kappel, William M.

    2014-01-01

    The Tully Valley, located in southern Onondaga County, New York, has a long history of unusual natural hydrogeologic phenomena including mudboils (Kappel, 2009), landslides (Tamulonis and others, 2009; Pair and others, 2000), landsurface subsidence (Hackett and others, 2009; Kappel, 2009), and a brine-filled sinkhole or “Solar pond” (fig. 1), which is documented in this report. A solar pond is a pool of salty water (brine) which stores the sun’s energy in the form of heat. The saltwater naturally forms distinct layers with increasing density between transitional zones (haloclines) of rapidly changing specific conductance with depth. In a typical solar pond, the top layer has a low salt content and is often times referred to as the upper convective zone (Lu and others, 2002). The bottom layer is a concentrated brine that is either convective or temperature stratified dependent on the surrounding environment. Solar insolation is absorbed and stored in the lower, denser brine while the overlying halocline acts as an insulating layer and prevents heat from moving upwards from the lower zone (Lu and others, 2002). In the case of the Tully Valley solar pond, water within the pond can be over 90 degrees Fahrenheit (°F) in late summer and early fall. The purpose of this report is to summarize observations at the Tully Valley brine-filled sinkhole and provide supplemental climate data which might affect the pond salinity gradients insolation (solar energy).

  2. Minimizing the Environmental Impact of Sea Brine Disposal by Coupling Desalination Plants with Solar Saltworks: A Case Study for Greece

    Directory of Open Access Journals (Sweden)

    Stylianos Gialis

    2010-02-01

    Full Text Available The explosive increase in world population, along with the fast socio-economic development, have led to an increased water demand, making water shortage one of the greatest problems of modern society. Countries such as Greece, Saudi Arabia and Tunisia face serious water shortage issues and have resorted to solutions such as transporting water by ships from the mainland to islands, a practice that is expensive, energy-intensive and unsustainable. Desalination of sea-water is suitable for supplying arid regions with potable water, but extensive brine discharge may affect marine biota. To avoid this impact, we explore the option of directing the desalination effluent to a solar saltworks for brine concentration and salt production, in order to achieve a zero discharge desalination plant. In this context, we conducted a survey in order to evaluate the potential of transferring desalination brine to solar saltworks, so that its disposal to the sea is avoided. Our analysis showed that brine transfer by trucks is prohibitively expensive. In order to make the zero discharge desalination plant economically feasible, efforts should be directed into developing a more efficient technology that will result in the production of only a fraction of the brine that is produced from our systems today.

  3. Chemical and isotopic constrains on the origin of brine and saline groundwater in Hetao plain, Inner Mongolia.

    Science.gov (United States)

    Liu, Jun; Chen, Zongyu; Wang, Lijuan; Zhang, Yilong; Li, Zhenghong; Xu, Jiaming; Peng, Yurong

    2016-08-01

    The origin and evolution of brine and saline groundwater have always been a challenged work for geochemists and hydrogeologists. Chemical and isotopic data of brine and saline waters were used to trace the sources of salinity and therefore to understand the transport mechanisms of groundwater in Xishanzui, Inner Mongolia. Both Cl/Br (molar) versus Na/Br (molar) and Cl (meq/L) versus Na (meq/L) indicated that salinity was from halite dissolution or at least a significant impact by halite dissolution. The logarithmic plot of the concentration trends of Cl (mg/L) versus Br (mg/L) for the evaporation of seawater and the Qinghai Salt Lake showed that the terrestrial halite dissolution was the dominated contribution for the salinity of this brine. The stable isotope ratios of hydrogen and oxygen suggested that the origin of brine was from paleorecharge water which experienced mixing of modern water in shallow aquifer. δ(37)Cl values ranged from -0.02 to 3.43 ‰ (SMOC), and reflecting mixing of different sources. The Cl isotopic compositions suggest that the dissolution of halite by paleometeoric water had a great contribution to the salinity of brine, and the contributions of the residual seawater and the dissolution of halite by the Yellow River water could be excluded.

  4. New PSA high concentration solar furnace SF40

    Science.gov (United States)

    Rodriguez, Jose; Cañadas, Inmaculada; Zarza, Eduardo

    2016-05-01

    A new solar furnace has been designed and built at Plataforma Solar de Almería. In this work, its main components such as heliostat, concentrator, attenuator and test table, and the method used to align them are described. Other equipment like the auxiliary systems necessary for the solar operation, vacuum chamber and gas system are outlined too. Finally, the thermal characteristics of the focus were measured during a test campaign, where different planes along the optical axis were scanned with a radiometer, and the peak flux was obtained and is presented in the last section of this report.

  5. High-performance flat-panel solar thermoelectric generators with high thermal concentration.

    Science.gov (United States)

    Kraemer, Daniel; Poudel, Bed; Feng, Hsien-Ping; Caylor, J Christopher; Yu, Bo; Yan, Xiao; Ma, Yi; Wang, Xiaowei; Wang, Dezhi; Muto, Andrew; McEnaney, Kenneth; Chiesa, Matteo; Ren, Zhifeng; Chen, Gang

    2011-05-01

    The conversion of sunlight into electricity has been dominated by photovoltaic and solar thermal power generation. Photovoltaic cells are deployed widely, mostly as flat panels, whereas solar thermal electricity generation relying on optical concentrators and mechanical heat engines is only seen in large-scale power plants. Here we demonstrate a promising flat-panel solar thermal to electric power conversion technology based on the Seebeck effect and high thermal concentration, thus enabling wider applications. The developed solar thermoelectric generators (STEGs) achieved a peak efficiency of 4.6% under AM1.5G (1 kW m(-2)) conditions. The efficiency is 7-8 times higher than the previously reported best value for a flat-panel STEG, and is enabled by the use of high-performance nanostructured thermoelectric materials and spectrally-selective solar absorbers in an innovative design that exploits high thermal concentration in an evacuated environment. Our work opens up a promising new approach which has the potential to achieve cost-effective conversion of solar energy into electricity.

  6. Lygus hesperus (Heteroptera: Miridae) tolerates high concentrations of dietary nickel

    Institute of Scientific and Technical Information of China (English)

    ROBERT S. BOYD

    2007-01-01

    Nickel hyperaccumulator plants contain unusually elevated levels of Ni (> 1 000 μg Ni/g). Some insect herbivores, including Lygus hesperus (Western tarnished plant bug), have been observed feeding on the California Ni hyperaccumulator Streptanthus polygaloides. This bug may be able to utilize S. polygaloides as a host either through its feeding behavior or by physiological tolerance of Ni. This experiment determined the Ni tolerance of L. hesperus by offering insects artificial diet amended with 0,0.4, 1, 2, 4.5,10, 20 and 40 mmol Ni/L and recording survival. Survival varied due to Ni concentration, with diets containing 10 mmol Ni/L and greater resulting in significantly lower survival compared to the control (0 mmol Ni/L) treatment. Insects tolerated diet containing as much as 4.5 mmol Ni/L, a relatively elevated Ni concentration. I conclude that L. hesperus can feed on S. polygaloides because it is Ni-tolerant, probably due to physiological mechanisms that provide it with resistance to plant chemical defenses including elemental defenses such as hyperaccumulated Ni.

  7. A Novel Ion Exchange System to Purify Mixed ISS Waste Water Brines for Chemical Production and Enhanced Water Recovery

    Science.gov (United States)

    Lunn, Griffin; Spencer, LaShelle; Ruby, Anna-Maria; McCaskill, Andrew

    2014-01-01

    Current International Space Station water recovery regimes produce a sizable portion of waste water brine. This brine is highly toxic and water recovery is poor: a highly wasteful proposition. With new biological techniques that do not require waste water chemical pretreatment, the resulting brine would be chromium-free and nitrate rich which can allow possible fertilizer recovery for future plant systems. Using a system of ion exchange resins we can remove hardness, sulfate, phosphate and nitrate from these brines to leave only sodium and potassium chloride. At this point modern chlor-alkali cells can be utilized to produce a low salt stream as well as an acid and base stream. The first stream can be used to gain higher water recovery through recycle to the water separation stage while the last two streams can be used to regenerate the ion exchange beds used here, as well as other ion exchange beds in the ISS. Conveniently these waste products from ion exchange regeneration would be suitable as plant fertilizer. In this report we go over the performance of state of the art resins designed for high selectivity of target ions under brine conditions. Using ersatz ISS waste water we can evaluate the performance of specific resins and calculate mass balances to determine resin effectiveness and process viability. If this system is feasible then we will be one step closer to closed loop environmental control and life support systems (ECLSS) for current or future applications.

  8. High Energy Density Lithium Air Batteries for Oxygen Concentrators Project

    Data.gov (United States)

    National Aeronautics and Space Administration — For NASA's Exploration Medical Capabilities mission, extremely high specific energy power sources, with specific energy over 2000 Wh/kg, are urgently sought after....

  9. Conservação de filés de tilápia-do-nilo (Oreochromis niloticus em salga seca e salga úmida Nile tilapia (Oreochromis niloticus preservation by means of dry salting and saturated brine

    Directory of Open Access Journals (Sweden)

    F.S. Aiura

    2008-12-01

    Full Text Available Acompanhou-se o desenvolvimento dos processos da salga em salmoura saturada (salga úmida e salga seca de filés de tilápia-do-nilo (Oreochromis niloticus e avaliaram-se algumas características indicativas de qualidade do produto durante a estocagem. Os processos foram acompanhados por 156 horas na salga úmida e por 96 horas na salga seca, e os filés salgados foram estocados, respectivamente, por 60 e 45 dias à temperatura ambiente. Os teores máximos de cloreto nos filés (14% foram atingidos com 72 horas na salga úmida e com 36 horas na salga seca. Os filés de tilápia salgados em salmoura mantiveram as características próprias do produto por um período de 45 dias, e os submetidos à salga seca apresentaram baixo teor de umidade (6% e alta concentração de extrato etéreo (4,6%. Recomenda-se somente o processo de salga em salmoura saturada como forma de conservação dos filés de tilápia-do-nilo.The processes of salting of Nile tilapia fillets (Oreochromis niloticus submitted to saturated brine and dry salting were observed, and some characteristics that indicate the quality of the product during the storage were evaluated. The brine saturated process was followed up to 156 hours and the dry salting was followed up to 96 hours. When the salting finished, fillets were stored for 45 (dry salting and 60 days (saturated brine, respectively. The highest values for chloride in fillets (14% were reached within 72 hours in brine salting and 36 hours in dry salting. The tilapia fillets salted in brine kept the proper characteristics of the product for a period of 45 days and the fillets submitted to dry salting showed low moisture ratios (6% and a high concentration of lipids (4.6%. Thereby, it is only recommended the salting process in saturated brine to be used as a mean of conservation for Nile tilapia fillets.

  10. Brine production strategy modeling for active and integrated management of water resources in CCS

    Science.gov (United States)

    Court, B.; Celia, M. A.; Nordbotten, J. M.; Buscheck, T. A.; Elliot, T. J.; Bandilla, K.; Dobossy, M.

    2010-12-01

    Our society is at present highly dependent on coal, which will continue to play a major role in baseload electricity production in the coming decades. Most projected climate change mitigation strategies require CO2 Capture and Sequestration (CCS) as a vital element to stabilize CO2 atmospheric emissions. In these strategies, CCS will have to expand in the next two decades by several orders of magnitude compared to current worldwide implementation. At present the interactions among freshwater extraction, CO2 injection, and brine management are being considered too narrowly across CCS operations, and in the case of freshwater almost completely overlooked. Following the authors’ recently published overview of these challenges, an active and integrated management of water resources throughout CCS operations was proposed to avoid overlooking critical challenges that may become major obstacles to CCS implementation. Water resources management is vital for several reasons including that a coal-fired power plant retrofitted for CCS requires twice as much cooling water as the original plant. However this increased demand may be accommodated by brine extraction and treatment, which would concurrently function as large-scale pressure management and a potential source of freshwater. Synergistic advantages of such proactive integration that were identified led the authors to concluded that: Active management of CCS operations through an integrated approach -including brine production, treatment, use for cooling, and partial reinjection- can address challenges simultaneously with several synergistic advantages; and, that freshwater and brine must be linked to CO2 and pressure as key decision making parameters throughout CCS operations while recognizing scalability and potential pore space competition challenges. This work presents a detailed modeling investigation of a potential integration opportunity resulting from brine production. Technical results will focus solely on the

  11. Celecoxib concentration predicts decrease in prostaglandin E2 concentrations in nipple aspirate fluid from high risk women

    Directory of Open Access Journals (Sweden)

    Flynn John T

    2008-02-01

    Full Text Available Abstract Background Epidemiologic studies suggest that long term low dose celecoxib use significantly lowers breast cancer risk. We previously demonstrated that 400 mg celecoxib taken twice daily for 2 weeks lowered circulating plasma and breast nipple aspirate fluid (NAF prostaglandin (PGE2 concentrations in post- but not premenopausal high risk women. We hypothesized that circulating concentrations of celecoxib influenced PGE2 response, and that plasma levels of the drug are influenced by menopausal status. To address these hypotheses, the aims of the study were to determine: 1 if circulating plasma concentrations of celecoxib correlated with the change in plasma or NAF PGE2 concentrations from baseline to end of treatment, and 2 whether menopausal status influenced circulating levels of celecoxib. Methods Matched NAF and plasma were collected from 46 high risk women who were administered celecoxib twice daily for two weeks, 20 subjects receiving 200 mg and 26 subjects 400 mg of the agent. NAF and plasma samples were collected before and 2 weeks after taking celecoxib. Results In women taking 400 mg bid celecoxib, plasma concentrations of the agent correlated inversely with the change in NAF PGE2 levels from pre- to posttreatment. Nonsignificant trends toward higher celecoxib levels were observed in post- compared to premenopausal women. There was a significant decrease in NAF but not plasma PGE2 concentrations in postmenopausal women who took 400 mg celecoxib (p = 0.03. Conclusion In high risk women taking 400 mg celecoxib twice daily, plasma concentrations of celecoxib correlated with downregulation of PGE2 production by breast tissue. Strategies synergistic with celecoxib to downregulate PGE2 are of interest, in order to minimize the celecoxib dose required to have an effect.

  12. Waste Isolation Pilot Plant Performance Assessment: Radionuclide Release Sensitivity to Diminished Brine and Gas Flows to/from Transuranic Waste Disposal Areas

    Directory of Open Access Journals (Sweden)

    Brad A. Day

    2017-03-01

    Full Text Available Waste Isolation Pilot Plant repository releases are evaluated through the application of modified parameters to simulate accelerated creep closure, include capillary pressure effects on relative permeability, and increase brine and gas saturation in the operations and experimental (OPS/EXP areas. The modifications to the repository model result in increased pressures and decreased brine saturations in waste areas and increased pressures and brine saturations in the OPS/EXP areas. Brine flows up the borehole during a hypothetical drilling intrusion are nearly identical and brine flows up the shaft are decreased. The modified parameters essentially halt the flow of gas from the southern waste areas to the northern nonwaste areas, except as transported through the marker beds and anhydrite layers. The combination of slightly increased waste region pressures and very slightly decreased brine saturations result in a modest increase in spallings and no significant effect on direct brine releases, with total releases from the Culebra and cutting and caving releases unaffected. Overall, the effects on total high-probability mean releases from the repository are insignificant, with total low-probability mean releases minimally increased. It is concluded that the modified OPS/EXP area parameters have an insignificant effect on the prediction of total releases.

  13. Waste isolation pilot plant performance assessment: Radionuclide release sensitivity to diminished brine and gas flows to/from transuranic waste disposal areas

    Energy Technology Data Exchange (ETDEWEB)

    Day, Brad A.; Camphouse, R. C.; Zeitler, Todd R. [Sandia National Laboratories, Carlsbad (United States)

    2017-03-15

    Waste Isolation Pilot Plant repository releases are evaluated through the application of modified parameters to simulate accelerated creep closure, include capillary pressure effects on relative permeability, and increase brine and gas saturation in the operations and experimental (OPS/EXP) areas. The modifications to the repository model result in increased pressures and decreased brine saturations in waste areas and increased pressures and brine saturations in the OPS/EXP areas. Brine flows up the borehole during a hypothetical drilling intrusion are nearly identical and brine flows up the shaft are decreased. The modified parameters essentially halt the flow of gas from the southern waste areas to the northern nonwaste areas, except as transported through the marker beds and anhydrite layers. The combination of slightly increased waste region pressures and very slightly decreased brine saturations result in a modest increase in spallings and no significant effect on direct brine releases, with total releases from the Culebra and cutting and caving releases unaffected. Overall, the effects on total high-probability mean releases from the repository are insignificant, with total low-probability mean releases minimally increased. It is concluded that the modified OPS/EXP area parameters have an insignificant effect on the prediction of total releases.

  14. Determination of water quality variables, endotoxin concentration, and enterobacteriaceae concentration and identification in Southern High Plains dairy lagoons

    Science.gov (United States)

    The objectives of this study were to determine the concentration of endotoxin, determine 20 water quality variables, and identify and enumerate fungal and bacterial pathogens from United States southern High Plains dairy lagoons and control lakes during summer and winter. Water samples were collecte...

  15. High-Performance Near-Infrared Luminescent Solar Concentrators.

    Science.gov (United States)

    Rondão, Raquel; Frias, Ana R; Correia, Sandra F H; Fu, Lianshe; de Zea Bermudez, Verónica; André, Paulo S; Ferreira, Rute A S; Carlos, Luís D

    2017-04-12

    Luminescent solar concentrators (LSCs) appear as candidates to enhance the performance of photovoltaic (PV) cells and contribute to reduce the size of PV systems, decreasing, therefore, the amount of material needed and thus the cost associated with energy conversion. One way to maximize the device performance is to explore near-infrared (NIR)-emitting centers, resonant with the maximum optical response of the most common Si-based PV cells. Nevertheless, very few examples in the literature demonstrate the feasibility of fabricating LSCs emitting in the NIR region. In this work, NIR-emitting LSCs are reported using silicon 2,3-naphthalocyanine bis(trihexylsilyloxide) (SiNc or NIR775) immobilized in an organic-inorganic tri-ureasil matrix (t-U(5000)). The photophysical properties of the SiNc dye incorporated into the tri-ureasil host closely resembled those of SiNc in tetrahydrofuran solution (an absolute emission quantum yield of ∼0.17 and a fluorescence lifetime of ∼3.6 ns). The LSC coupled to a Si-based PV device revealed an optical conversion efficiency of ∼1.5%, which is among the largest values known in the literature for NIR-emitting LSCs. The LSCs were posteriorly coupled to a Si-based commercial PV cell, and the synergy between the t-U(5000) and SiNc molecules enabled an effective increase in the external quantum efficiency of PV cells, exceeding 20% in the SiNc absorption region.

  16. An astigmatic corrected target-aligned heliostat for high concentration

    Energy Technology Data Exchange (ETDEWEB)

    Zaibel, R.; Dagan, E.; Karni, J. [Solar Research Facility, The Weizmann Institute of Science, Rehovot (Israel); Ries, Harald [Ludwig-Maximilians-Universitaet, Sektion Physik, Munich (Germany)

    1995-05-28

    Conventional heliostats suffer from astigmatism for non-normal incidence. For tangential rays the focal length is shortened while for sagittal rays it is longer than the nominal focal length. Due to this astigmatism it is impossible to produce a sharp image of the sun, and the rays will be spread over a larger area. In order to correct this the heliostat should have different curvature radii along the sagittal and tangential direction in the heliostat plane just like a non axial part of a paraboloid. In conventional heliostats, where the first axis, fixed with respect to the ground, is vertical while the second, fixed with respect to the reflector surface, is horizontal, such an astigmatism correction is not practical because the sagittal and tangential directions rotate with respect to the reflector. We suggest an alternative mount where the first axis is oriented towards the target. The second axis, perpendicular to the first and tangent to the reflector, coincides with the tangential direction. With this mounting sagittal and tangential direction are fixed with respect to the reflector during operation. Therefore a partial astigmatism compensation is possible. We calculate the optimum correction and show the performance of the heliostat. We also show predicted yearly average concentrations

  17. Schiff base: A high affinity chemical agent to decrease the concentration of aflatoxin M1 in raw milk contaminated artificially

    Directory of Open Access Journals (Sweden)

    Frane Delaš

    2012-03-01

    Full Text Available In the present study were conducted the effect of pH (5.5, 6.0 and 6.5 and concentration of new synthesized 3-/2-aminophenylimino-(p-toluoyl/-4-hydroxy-6-(p-tolyl-2H-pyrane-2-one (Schiff base on decrease the concentration of aflatoxin M1 (AFM1 in raw milk contaminated with known concentration of this toxin. Experiments were carried out at temperature of 4 °C during 35 days. At pH 5.5 Schiff base concentration of 0.1 µmol/L was lessening the concentration of AFM1 after 35 days by 55 %. However, at pH 6.5 the most effective concentration for lessening of AFM1 was 0.5 µmol/L. Schiff base was not effective at pH value of 7 or higher. The ability of Schiff base to act as antimycotoxigenic agent provides new perspective for possibly using this compound to control AFM1 contamination in milk and to extent shelf lives of this food. Detection of toxicity of investigated Schiff base was performed by using the brine shrimp (Artemia salina larvae as an biological indicator to determine their sensitivity to this chemical agent.

  18. Toxicological investigations of Aloe ferox Mill. extracts using Brine shrimp (Artemia salina L.) assay.

    Science.gov (United States)

    Abosede, Wintola Olubunmi; Sunday, Arowosegbe; Jide, Afolayan Anthony

    2015-03-01

    Cytotoxicity of the extracts of Aloe ferox using brine shrimp was evaluated. Effects of the extracts on hatchability and lethality of brine shrimps were reported in terms of minimum inhibitory concentration and LD(50) respectively. The hatching success was in the order: aqueous root extract (39.8%) >aqueous leaf (26.5%) >acetone leaf (13.7%) > ethanol leaf extracts (2.5%). Hatchability in incubations of ethanol and acetone extracts was found to be dose - dependent, with hatching success decreasing as the concentration of the extracts increased. The lethality of extracts was in the order: aqueous leaf extract (4.7%) >aqueous root extract (4.2%) >acetone leaf extract (3.5%) >ethanol root extract (2.6%) > ethanol leaf extract (1.8%) >acetone root extract (0.7%). Mean mortality of nauplii in the control was higher (6.7%) than that of all the extracts. Based on Meyer's index of toxicity, the acetone leaf extract with LD(50) >1.0mg/mL could be considered as non toxic, while the ethanol root extract (LD(50) brine shrimp. Since the extracts of A. ferox have consistently exhibited significant pharmaceutical properties in-vitro, the non-toxic extracts could further be exploited for the development of plant-based pharmaceuticals.

  19. Brine Organisms and the Question of Habitat Specific Adaptation

    Science.gov (United States)

    Siegel, B. Z.; Siegel, S. M.; Speitel, Thomas; Waber, Jack; Stoecker, Roy

    1984-12-01

    Among the well-known ultrasaline terrestrial habitats, the Dead Sea in the Jordan Rift Valley and Don Juan Pond in the Upper Wright Valley represent two of the most extreme. The former is a saturated sodium chloride-magnesium sulfate brine in a hot desert, the latter a saturated calcium chloride brine in an Antarctic desert. Both Dead Sea and Don Juan water bodies themselves are limited in microflora, but the saline Don Juan algal mat and muds contain abundant nutrients and a rich and varied microbiota, including Oscillatoria, Gleocapsa, Chlorella, diatoms, Penicillium and bacteria. In such environments, the existence of an array of specific adaptations is a common, and highly reasonable, presumption, at least with respect to habitat-obligate forms. Nevertheless, many years of ongoing study in our laboratory have demonstrated that lichens (e.g. Cladonia), algae (e.g. Nostoc) and fungi (e.g. Penicillium, Aspergillus) from the humid tropics can sustain metabolism down to -40°C and growth down to -10°C in simulated Dead Sea or Don Juan (or similar) media without benefit of selection or gradual acclimation. Non-selection is suggested in fungi by higher growth rates from vegetative inocula than spores. The importance of nutrient parameters was also evident in responses to potassium and reduced nitrogen compounds. In view of the saline performance of tropical Nostoc, and its presence in the Antarctic dry valley soils, its complete absence in our Don Juan mat samples was and remains a puzzle. We suggest that adaptive capability is already resident in many terrestrial life forms not currently in extreme habitats, a possible reflection of evolutionary selection for wide spectrum environmental adaptability.

  20. Emulsifier development for high-concentrated reverse emulsions

    OpenAIRE

    Kovalenko, I. L.; V.P. Kuprin

    2016-01-01

    The reverse emulsions have found broad application in ore mining industry as matrixes of emulsion explosive substances and boring washing waters. The defining characteristic of reverse emulsions of industrial explosive substances is the high stability and immunity to crystallization. Aim: The aim of this work is to assess the mechanism of emulsifiers effect like SMO and some PIBSA-derivatives, that are most abundantly used in world practice, and also to develop an effective domestic emulsifie...

  1. High urinary phthalate concentration associated with delayed pubarche in girls

    DEFF Research Database (Denmark)

    Frederiksen, H; Sørensen, K; Mouritsen, A;

    2012-01-01

    Phthalates are a group of chemicals present in numerous consumer products. They have anti-androgenic properties in experimental studies and are suspected to be involved in human male reproductive health problems. A few studies have shown associations between phthalate exposure and changes...... and controls. We demonstrated that delayed pubarche, but not thelarche, was associated with high phthalate excretion in urine samples from 725 healthy school girls, which may suggest anti-androgenic actions of phthalates in our study group of girls....

  2. Deep Sea Memory of High Atmospheric CO2 Concentration

    Science.gov (United States)

    Mathesius, Sabine; Hofmann, Matthias; Caldeira, Ken; Schellnhuber, Hans Joachim

    2015-04-01

    Carbon dioxide removal (CDR) from the atmosphere has been proposed as a powerful measure to mitigate global warming and ocean acidification. Planetary-scale interventions of that kind are often portrayed as "last-resort strategies", which need to weigh in if humankind keeps on enhancing the climate-system stock of CO2. Yet even if CDR could restore atmospheric CO2 to substantially lower concentrations, would it really qualify to undo the critical impacts of past emissions? In the study presented here, we employed an Earth System Model of Intermediate Complexity (EMIC) to investigate how CDR might erase the emissions legacy in the marine environment, focusing on pH, temperature and dissolved oxygen. Against a background of a world following the RCP8.5 emissions path ("business-as-usual") for centuries, we simulated the effects of two massive CDR interventions with CO2 extraction rates of 5 GtC yr-1 and 25 GtC yr-1, respectively, starting in 2250. We found that the 5 GtC yr-1 scheme would have only minor ameliorative influence on the oceans, even after several centuries of application. By way of contrast, the extreme 25 GtC yr-1 scheme eventually leads to tangible improvements. However, even with such an aggressive measure, past CO2 emissions leave a substantial legacy in the marine environment within the simulated period (i.e., until 2700). In summary, our study demonstrates that anthropogenic alterations of the oceans, caused by continued business-as-usual emissions, may not be reversed on a multi-centennial time scale by the most aspirational geoengineering measures. We also found that a transition from the RCP8.5 state to the state of a strong mitigation scenario (RCP2.6) is not possible, even under the assumption of extreme extraction rates (25 GtC yr-1). This is explicitly demonstrated by simulating additional scenarios, starting CDR already in 2150 and operating until the atmospheric CO2 concentration reaches 280 ppm and 180 ppm, respectively. The simulated

  3. High plasma uric acid concentration: causes and consequences

    Directory of Open Access Journals (Sweden)

    de Oliveira Erick

    2012-04-01

    Full Text Available Abstract High plasma uric acid (UA is a precipitating factor for gout and renal calculi as well as a strong risk factor for Metabolic Syndrome and cardiovascular disease. The main causes for higher plasma UA are either lower excretion, higher synthesis or both. Higher waist circumference and the BMI are associated with higher insulin resistance and leptin production, and both reduce uric acid excretion. The synthesis of fatty acids (tryglicerides in the liver is associated with the de novo synthesis of purine, accelerating UA production. The role played by diet on hyperuricemia has not yet been fully clarified, but high intake of fructose-rich industrialized food and high alcohol intake (particularly beer seem to influence uricemia. It is not known whether UA would be a causal factor or an antioxidant protective response. Most authors do not consider the UA as a risk factor, but presenting antioxidant function. UA contributes to > 50% of the antioxidant capacity of the blood. There is still no consensus if UA is a protective or a risk factor, however, it seems that acute elevation is a protective factor, whereas chronic elevation a risk for disease.

  4. Evaporation Rates of Brine on Mars

    Science.gov (United States)

    Sears, D. W. G.; Chittenden, J.; Moore, S. R.; Meier, A.; Kareev, M.; Farmer, C. B.

    2004-01-01

    While Mars is now largely a dry and barren place, recent data have indicated that water has flowed at specific locations within the last approx. 10(exp 6) y. This had led to a resurgence of interest in theoretical and experimental work aimed at understanding the behavior of water on Mars. There are several means whereby the stability of liquid water on Mars could be increased, one being the presence solutes that would depress the freezing point. Salt water on Earth is about 0.5M NaCl, but laboratory experiments suggest that martian salt water is quite different. We recently began a program of laboratory measurements of the stability of liquid water, ice and ice-dust mixtures under martian conditions and here report measurements of the evaporation rate of 0.25M brine.

  5. Design requirements for high-efficiency high concentration ratio space solar cells

    Science.gov (United States)

    Rauschenbach, H.; Patterson, R.

    1980-01-01

    A miniaturized Cassegrainian concentrator system concept was developed for low cost, multikilowatt space solar arrays. The system imposes some requirements on solar cells which are new and different from those imposed for conventional applications. The solar cells require a circular active area of approximately 4 mm in diameter. High reliability contacts are required on both front and back surfaces. The back area must be metallurgically bonded to a heat sink. The cell should be designed to achieve the highest practical efficiency at 100 AMO suns and at 80 C. The cell design must minimize losses due to nonuniform illumination intensity and nonnormal light incidence. The primary radiation concern is the omnidirectional proton environment.

  6. PILOT TESTING: PRETREATMENT OPTIONS TO ALLOW RE-USE OF FRAC FLOWBACK AND PRODUCED BRINE FOR GAS SHALE RESOURCE DEVELOPMENT

    Energy Technology Data Exchange (ETDEWEB)

    Burnett, David

    2012-12-31

    The goal of the A&M DOE NETL Project No. DE-FE0000847 was to develop a mobile, multifunctional water treatment capability designed specifically for “pre-treatment” of field waste brine. The project consisted of constructing s mobile “field laboratory” incorporating new technology for treating high salinity produced water and using the lab to conduct a side-by-side comparison between this new technology and that already existing in field operations. A series of four field trials were performed utilizing the mobile unit to demonstrate the effectiveness of different technology suitable for use with high salinity flow back brines and produced water. The design of the mobile unit was based on previous and current work at the Texas A&M Separation Sciences Pilot Plant. The several treatment techniques which have been found to be successful in both pilot plant and field tests had been tested to incorporate into a single multifunctional process train. Eight different components were evaluated during the trials, two types of oil and grease removal, one BTEX removal step, three micro-filters, and two different nanofilters. The performance of each technique was measured by its separation efficiency, power consumption, and ability to withstand fouling. The field trials were a success. Four different field brines were evaluated in the first trial in New York. Over 16,000 gallons of brine were processed. Using a power cost of $.10 per kWh, media pretreatment power use averaged $0.004 per barrel, solids removal $.04 per barrel and brine “softening” $.84 per barrel. Total power cost was approximately $1.00 per barrel of fluid treated. In Pennsylvania, brines collected from frac ponds were tested in two additional trials. Each of the brines was converted to an oil-free, solids-free brine with no biological activity. Brines were stable over time and would be good candidates for use as a make-up fluid in a subsequent fracturing fluid design. Reports on all of the field

  7. Characterization of blood donors with high haemoglobin concentration

    DEFF Research Database (Denmark)

    Magnussen, K; Hasselbalch, H C; Ullum, H;

    2013-01-01

    Background and Objectives  The literature contains little on the prevalence and causes of high predonation haemoglobin levels among blood donors. This study aimed to characterize and develop an algorithm to manage would-be donors with polycythaemia. Materials and Methods  Between November 2009......, erythropoietin, ferritin, platelet count and leucocyte count, JAK2 V617 and JAK2 exon12 analysis, as well as other routine measurements. Results  Among 46 such donors, 39 had a history of smoking, which contributes to erythrocytosis. Two had PV, five had severe hypertension, one of them because of renal artery...

  8. Waste to Energy Potential - A High Concentration Anaerobic Bioreactor

    Science.gov (United States)

    2012-05-23

    REPORT DATE 23 MAY 2012 2. REPORT TYPE 3. DATES COVERED 00-00-2012 to 00-00-2012 4. TITLE AND SUBTITLE Waste to Energy Potential - A High...and fermentative bacteria break down organic carbon to VFAs Acetogens break down VFAs to CH3CO2 − and H2 + Acetoclastic methanogens break...s -999999 999999 7 481 su -999999 999999 0 .. -999999 999999 HCA8 pti Flo$&-tdgc Tan.\\ feed su -999999 999999 0 .. -999999 999999 A-l>o -999999

  9. Recent testing of secondary concentrators at NREL`s high-flux solar furnace

    Energy Technology Data Exchange (ETDEWEB)

    Jenkins, D.; Winston, R.; O`Gallagher, J. [Univ. of Chicago, IL (United States); Bingham, C.; Lewandowski, A.; Pitts, R.; Scholl, K. [National Renewable Energy Lab., Golden, CO (United States)

    1996-12-31

    Several tests have been completed on new secondary concentrators at the High-Flux Solar Furnace (HFSF) at the National Renewable Energy Laboratory (NREL). The first test measured the power from the exit of a High-Index secondary that achieves an average concentration of 50,000 suns. The second concentrator tested pumped an Nd:YAG laser crystal. The concentrator designs are presented, along with data from on-sun testing at the HFSF.

  10. Empirical formula for the refractive index of freezing brine

    DEFF Research Database (Denmark)

    Frisvad, Jeppe Revall

    2009-01-01

    The refractive index of freezing brine is important for example in order to estimate oceanic scattering as sea ice develops. Previously, no simple continuous expression was available for estimating the refractive index of brine at subzero temperatures. I show that extrapolation of the empirical...... formula for the refractive index of seawater by Quan and Fry [Appl. Opt. 34(18), 3477-3480 (1995)] provides a good fit to the refractive index of freezing brine for temperatures above -24 degrees celsius and salinities below 180 parts per thousand....

  11. Short-lived brine infiltration during upper amphibolite facies metamorphism in the continental collision zone

    Science.gov (United States)

    Higashino, Fumiko; Kawakami, Tetsuo; Tsuchiya, Noriyoshi; Satish-Kumar, Madhusoodhan; Ishikawa, Masahiro; Grantham, Geoffrey; Sakata, Shuhei; Hirata, Takafumi

    2017-04-01

    The importance of brine is increasingly recognized because of its role on mass transportation at the mid- to lower-crustal pressure-temperature (P-T) conditions (e.g., Newton & Manning, 2010). However, the passage and residence times of brine are not well understood. This study deals with garnet-hornblende (Grt-Hbl) veins, discordantly cutting the gneissose structure of garnet-orthopyroxene-hornblende gneiss from the central Sør Rondane Mountains (SRM), East Antarctica. The Cl contents of hornblende and biotite, K content of hornblende, and the thickness of Na-richer rims of plagioclase decreased with distance from the Grt-Hbl vein. The P-T conditions of the vein formation were estimated to be 680 °C, 0.69 GPa (Higashino et al., under review). In the wall rock in the vicinity of the vein, addition of Li, Cu, Rb, Ba, Pb, and U, which tend to be mobile in brines rather than in melts is observed, using Zr as an immobile element (Higashino et al., 2015). This indicates that the Grt-Hbl vein was formed by the infiltration of NaCl-KCl brine. Trace element concentrations in the wall rock minerals decrease with distance from the vein, and in most cases show concave up/down profiles. Distances where these concentrations in each mineral species become constant are dependent on elements, and not on mineral species. These profiles can be best modelled by diffusion equations, suggesting that the diffusion is the major process transferring the trace elements perpendicular to the vein. Although plagioclase does not show significant trace element zoning within each single grain, the discontinuous drop of anorthite content at rims is preserved. Thin brine films in grain boundaries presumably caused dissolution-reprecipitation (e.g., Ruiz-Agudo et al., 2014), and lattice diffusion in plagioclase would have followed this to form homogeneous trace element zonings. Therefore, the main process of brine infiltration into the wall rock is possibly grain boundary diffusion in wet

  12. High-order optical nonlinearities in nanocomposite films dispersed with semiconductor quantum dots at high concentrations

    Science.gov (United States)

    Tomita, Yasuo; Matsushima, Shun-suke; Yamagami, Ryu-ichi; Jinzenji, Taka-aki; Sakuma, Shohei; Liu, Xiangming; Izuishi, Takuya; Shen, Qing

    2017-06-01

    We describe the nonlinear optical properties of inorganic-organic nanocomposite films in which semiconductor CdSe quantum dots as high as 6.8 vol.% are dispersed. Open/closed Z-scan measurements, degenerate multi-wave mixing and femtosecond pump-probe/transient grating measurements are conducted. It is shown that the observed fifth-order optical nonlinearity has the cascaded third-order contribution that becomes prominent at high concentrations of CdSe QDs. It is also shown that there are picosecond-scale intensity-dependent and nanosecond-scale intensity-independent decay components in absorptive and refractive nonlinearities. The former is caused by the Auger process, while the latter comes from the electron-hole recombination process.

  13. Radioactive waste isolation in salt: geochemistry of brine in rock salt in temperature gradients and gamma-radiation fields - a selective annotated bibliography

    Energy Technology Data Exchange (ETDEWEB)

    Hull, A.B.; Williams, L.B.

    1985-07-01

    Evaluation of the extensive research concerning brine geochemistry and transport is critically important to successful exploitation of a salt formation for isolating high-level radioactive waste. This annotated bibliography has been compiled from documents considered to provide classic background material on the interactions between brine and rock salt, as well as the most important results from more recent research. Each summary elucidates the information or data most pertinent to situations encountered in siting, constructing, and operating a mined repository in salt for high-level radioactive waste. The research topics covered include the basic geology, depositional environment, mineralogy, and structure of evaporite and domal salts, as well as fluid inclusions, brine chemistry, thermal and gamma-radiation effects, radionuclide migration, and thermodynamic properties of salts and brines. 4 figs., 6 tabs.

  14. EXPERIMENTAL INVESTIGATIONS ON DIFFUSION CHARACTERISTICS OF HIGH CONCENTRATION JET FLOW IN NEAR REGION

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The diffusion characteristics of the high concentration jet flowissued from a round nozzle above the free surface into moving waterbody were experimentally investigated. By means of flow visualization technique, the diffusion behavior of the high concentration jet was observed and analysed, Concentration distribution in the near region was obtained by sampling and quantitative measurements. Experimental results indicate that the diffusion mechanics of the high concentration jet flow are greatly influenced by initial momentum, buoyancy, turbulent structure, ambient current and boundary conditions, showing complicated flow patterns and concentration distribution characteristics that are different from previous results for submerged jets.

  15. Optimisation of Fenton's reagent usage as a pre-treatment for fermentation brines.

    Science.gov (United States)

    Rivas, Francisco J; Beltrán, Fernando J; Gimeno, Olga; Alvarez, Pedro

    2003-01-31

    Pre-treatment of fermentation brines from green olives has been carried out by the Fe(II)/Fe(III)/H(2)O(2) system. Reagent concentration exerted a positive influence on chemical oxygen demand (COD) removal. Hydrogen peroxide uptake showed values in the range 0.3-1.6mol of COD eliminated per mol of H(2)O(2) consumed depending on operating conditions. The optimum working pH was found to be in the interval 2.0-3.5. Reaction temperature increased the COD degradation rate, although similar COD conversion values were obtained after 5h of treatment regardless of the value of this parameter. An analysis of the biodegradability of this type of effluent demonstrated the beneficial effect of the chemical pre-oxidation. According to the experimental results, it is suggested that there is an inhibitory effect of the wastewater due to its COD content and nature rather than attributable to the presence of high amounts of sodium chloride. Biodegradation efficiency increased as temperature was raised up to 30 degrees C. A further increase of this parameter up to 40 degrees C resulted in the death of the microorganisms.

  16. A computer program incorporating Pitzer's equations for calculation of geochemical reactions in brines

    Science.gov (United States)

    Plummer, L.N.; Parkhurst, D.L.; Fleming, G.W.; Dunkle, S.A.

    1988-01-01

    The program named PHRQPITZ is a computer code capable of making geochemical calculations in brines and other electrolyte solutions to high concentrations using the Pitzer virial-coefficient approach for activity-coefficient corrections. Reaction-modeling capabilities include calculation of (1) aqueous speciation and mineral-saturation index, (2) mineral solubility, (3) mixing and titration of aqueous solutions, (4) irreversible reactions and mineral water mass transfer, and (5) reaction path. The computed results for each aqueous solution include the osmotic coefficient, water activity , mineral saturation indices, mean activity coefficients, total activity coefficients, and scale-dependent values of pH, individual-ion activities and individual-ion activity coeffients , and scale-dependent values of pH, individual-ion activities and individual-ion activity coefficients. A data base of Pitzer interaction parameters is provided at 25 C for the system: Na-K-Mg-Ca-H-Cl-SO4-OH-HCO3-CO3-CO2-H2O, and extended to include largely untested literature data for Fe(II), Mn(II), Sr, Ba, Li, and Br with provision for calculations at temperatures other than 25C. An extensive literature review of published Pitzer interaction parameters for many inorganic salts is given. Also described is an interactive input code for PHRQPITZ called PITZINPT. (USGS)

  17. Water quality in the vicinity of Mosquito Creek Lake, Trumbull County, Ohio, in relation to the chemistry of locally occurring oil, natural gas, and brine

    Science.gov (United States)

    Barton, G.J.; Burruss, R.C.; Ryder, R.T.

    1998-01-01

    Sandstone water samples indicates that the gas is microbially generated, whereas the Clinton sandstone gases are thermogenically generated. Methane gas, in addition to crude oil, occurs naturally in the shallow Berea and Cussewago Sandstone aquifers in the Mosquito Creek Lake area and concentrations of dissolved methane are significant in the city of Cortland public-supply wells and in the domestic-supply wells near the southern shore of the lake. Water associated with oil and gas in the Clinton sandstone is a brine with high concentrations of chloride. Water from the Berea and Cussewago Sandstones, however, is fresh and potable. The contrasting geochemical characteristics are important for addressing water-quality issues that relate to oil and natural gas development in the Mosquito Creek area. A reexamination of the geologic framework and results of a subsurface-gas survey show that crude oil in the historic Mecca Oil Pool probably does not seep into Mosquito Creek Lake. Environmental samples show no evidence of any measurable release of oil, gas, or brine from the deeper Clinton sandstone oil and gas wells to the shallow aquifers, the lake, or lake tributaries. Brine is not associated with the hydrocarbons in the shallow Berea-Cussewago aquifer system and therefore cannot be a source of brine contamination. A mixing diagram constructed for dissolved bromide and chloride in surface water and water-supply wells shows no demonstrable mixing of these water resources with brine from the Clinton sandstone. There is some notable salinity in surface waters; however, the water is bromide poor, and a mixing diagram indicates that some local ground waters are influenced by halite solutions, presumably derived from leaching of road salt or from septic effluent.

  18. Emulsifier development for high-concentrated reverse emulsions

    Directory of Open Access Journals (Sweden)

    I.L. Kovalenko

    2016-05-01

    Full Text Available The reverse emulsions have found broad application in ore mining industry as matrixes of emulsion explosive substances and boring washing waters. The defining characteristic of reverse emulsions of industrial explosive substances is the high stability and immunity to crystallization. Aim: The aim of this work is to assess the mechanism of emulsifiers effect like SMO and some PIBSA-derivatives, that are most abundantly used in world practice, and also to develop an effective domestic emulsifier of reverse emulsions. Materials and methods: Using the semi-dynamic method with use of the reverse stalagmometer it was determined the decreasing in interfacial tension on “water / diesel fuel” border in the presence of 0.5 wt % sorbitan monooleate of various producers. Emulsions with use of the chosen emulsifiers using the dynamic mixer on the basis of monosolution of ammonium nitrate and diesel fuel have been produced. The emulsions have the following composition, wt %: ammonium nitrate – 76.8; water – 15.6; diesel fuel – 6.0; emulsifier – 1.6. Results: By the researches results of the interfacial tension “surfactant water / solution in diesel fuel”, the stability of emulsions using monosolution of ammonium nitrate and the IR spectrums of SMO of various producers it is established that presence in product of impurity of oleic acid, di- and trioleates leads to decreasing in interphase activity, increasing of emulsifier oil solubility and decreasing the resistance of emulsions to crystallization. On the basis of the spectral data analysis it is suggested about possibility of specific interaction on the mechanism of “spectral resonance” between emulsifiers of the PIBSA-MEA, LZX type and crystals nucleus of NH4NO3 ammonium nitrate in dispersed phase of emulsion. Amidation of vegetable oils by monoethanol amine is implemented at the reduced temperatures (90…100 °C. It was proved the availability mainly of fatty acids amides in product

  19. Experimental Study of Sorbitol Production by Zymomonas mobilis in High Sucrose Concentration

    OpenAIRE

    Rui Sérgio dos Santos Ferreira da Silva; João Batista Buzato; Maria Antonia Pedrine Colabone Celligoi; Marcos Roberto de Oliveira

    2004-01-01

    The sorbitol presents several industrial applications and its conventional production is of high cost and low yield. Sorbitol production by Zymomonas mobilis production has attracted attention as both production cost and environmental impact are low. The sorbitol plays an osmo-protective rule so that its production is promoted by high sugar concentrations. This work has evaluated the effect of high sucrose concentration in the sorbitol production. The raise of sucrose concentration from 100 t...

  20. Recovery Act: Molecular Simulation of Dissolved Inorganic Carbons for Underground Brine CO2 Sequestration

    Energy Technology Data Exchange (ETDEWEB)

    Goddard, William

    2012-11-30

    To further our understanding and develop the method for measuring the DICs under geological sequestration conditions, we studied the infrared spectra of DICs under high pressure and temperature conditions. First principles simulations of DICs in brine conditions were performed using a highly optimized ReaxFF-DIC forcefield. The thermodynamics stability of each species were determined using the 2PT method, and shown to be consistent with the Reax simulations. More importantly, we have presented the IR spectra of DIC in real brine conditions as a function of temperature and pressure. At near earth conditions, we find a breaking of the O-C-O bending modes into asymmetric and symmetric modes, separated by 100cm{sup -1} at 400K and 5 GPa. These results can now be used to calibrate FTIR laser measurements.

  1. INVESTIGATION ON PRODUCTION OF REFINED BRINE USED IN CHLORO—ALKALI MEMBRANE BY D 412 CHELATING RESIN

    Institute of Scientific and Technical Information of China (English)

    LIUFengzhi; LIHexian

    2001-01-01

    The adsorption property,the operating life,the operating exchange capacity and regeneration of D412 macroporous phosphonomethylamina chelating resin for removing Ca2+,Mg2+ and Fe2+ from high pH brine of alkali production by ionic membrane were investigated.The resin showed good physical-chemical and kinetic propoerty,high exchange capacity.excellent durability.

  2. INVESTIGATION ON PRODUCTION OF REFINED BRINE USED IN CHLORO-ALKALI MEMBRANE BY D412 CHELATING RESIN

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The adsorption property the operating life, the operating exchange capacity and regeneration of D412 macroporous phosphonomethylamina chelating resin for removing Ca2+,Mg2+ and Fe2+ from high pH brine of alkali production by ionic membrane were investigated The resin showed good physical-chemical and kinetic property, high exchange capacity, excellent durability.

  3. Molecular and phenetic characterization of the bacterial assemblage of Hot Lake, WA, an environment with high concentrations of magnesium sulphate, and its relevance to Mars

    Science.gov (United States)

    Kilmer, Brian R.; Eberl, Timothy C.; Cunderla, Brent; Chen, Fei; Clark, Benton C.; Schneegurt, Mark A.

    2014-01-01

    Hot Lake (Oroville, WA) is an athalassohaline epsomite lake that can have precipitating concentrations of MgSO4 salts, mainly epsomite. Little biotic study has been done on epsomite lakes and it was unclear whether microbes isolated from epsomite lakes and their margins would fall within recognized halotolerant genera, common soil genera or novel phyla. Our initial study cultivated and characterized epsotolerant bacteria from the lake and its margins. Approximately 100 aerobic heterotrophic microbial isolates were obtained by repetitive streak-plating in high-salt media including either 10% NaCl or 2 M MgSO4. The collected isolates were all bacteria, nearly evenly divided between Gram-positive and Gram-negative clades, the most abundant genera being Halomonas, Idiomarina, Marinobacter, Marinococcus, Nesterenkonia, Nocardiopsis and Planococcus. Bacillus, Corynebacterium, Exiguobacterium, Kocuria and Staphylococcus also were cultured. This initial study included culture-independent community analysis of direct DNA extracts of lake margin soil using PCR-based clone libraries and 16S rRNA gene phylogeny. Clones assigned to Gram-positive bacterial clades (70% of total clones) were dominated by sequences related to uncultured actinobacteria. There were abundant Deltaproteobacteria clones related to bacterial sulphur metabolisms and clones of Legionella and Coxiella. These epsomite lake microbial communities seem to be divided between bacteria primarily associated with hyperhaline environments rich in NaCl and salinotolerant relatives of common soil organisms. Archaea appear to be in low abundance and none were isolated, despite near-saturated salinities. Growth of microbes at very high concentrations of magnesium and other sulphates has relevance to planetary protection and life-detection missions to Mars, where scant liquid water may form as deliquescent brines and appear as eutectic liquids.

  4. Coiled Brine Recovery Assembly (CoBRA) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Coiled Brine Recovery Assembly (CoBRA) project will result in a proof-of-concept demonstration for a lightweight, compact, affordable, regenerable and disposable...

  5. Chlorate reduction in the brine circuit of a chlor-alkali electrolysis. Chlorat-Reduktion im Solekreislauf einer Chlor-Alkali-Elektrolyse

    Energy Technology Data Exchange (ETDEWEB)

    Rodermund, R.

    1983-02-25

    The influence of reactant concentrations and temperature on the rate and selectivity of the chlorate/hydrochloric acid reaction was determined experimentally. A model equation system was derived on the basis of a reaction mechanism describing the reaction between chlorate and hydrochloric acid at high H/sup +/ and Cl/sup -/ concentrations in the temperature range between 40 and 90/sup 0/C. The reaction of chlorate and hydrochloric acid was found to be sufficient to maintain a low chlorate level in the brine circuit of a chlor-alkali electrolysis. ClO/sub 2/ formation is negligible if suitable reaction conditions are chosen. Further, a model equation based on Henry's law was established for the solubility of ClO/sub 2/ in mixed solutions of HCl and NaCl in the temperature range of 40 to 90/sup 0/C.

  6. Recovery of biomolecules from marinated herring (Clupea harengus) brine using ultrafiltration through ceramic membranes

    DEFF Research Database (Denmark)

    Gringer, Nina; Hosseini, Seyed Vali; Svendsen, Tore;

    2015-01-01

    on recovery of high value biomolecules such as proteins, fatty acids, minerals, and phenolic compounds. Chemical and biological oxygen demand (COD, BOD5) as well as total suspended solids (TSS) were also measured to follow the performance of the ultrafiltration. The retentates contained 75-82% (95% TSS...... that ceramic ultrafiltration can recover biomolecules from marinated herring brines although pre-filtration optimization is still needed....

  7. Biochemical solubilization of toxic salts from residual geothermal brines and waste waters

    Science.gov (United States)

    Premuzic, Eugene T.; Lin, Mow S.

    1994-11-22

    A method of solubilizing metal salts such as metal sulfides in a geothermal sludge using mutant Thiobacilli selected for their ability to metabolize metal salts at high temperature is disclosed, The method includes the introduction of mutated Thiobacillus ferrooxidans and Thiobacillus thiooxidans to a geothermal sludge or brine. The microorganisms catalyze the solubilization of metal salts, For instance, in the case of metal sulfides, the microorganisms catalyze the solubilization to form soluble metal sulfates.

  8. Brine Shrimp Ecology In The Great Salt Lake, Utah

    OpenAIRE

    Wurtsbaugh, Wayne A.

    1995-01-01

    Hypersaline lakes are noted for their simple communities which facilitate understanding ecological interactions (Williams et al. 1990; Wurtsbaugh 1992; Jellison and Melack 1988). Nevertheless, we still cannot easily predict how environmental changes will effect the population dynamics in these lakes, at least in part because even these simple ecosystems may be more complex than we .realize. Many hypersaline lakes are dominated by the brine shrimp Artemia spp. The production of brine shrimp is...

  9. The effects of brine disposal on a subtidal meiofauna community

    Science.gov (United States)

    Riera, Rodrigo; Tuya, Fernando; Sacramento, Alicia; Ramos, Eva; Rodríguez, Myriam; Monterroso, Óscar

    2011-07-01

    Desalination plants generate notable (>1,000 s m 3) quantities of hypersaline brine which potentially affect the biological communities in the receiving area. We assessed whether proximity to a brine discharge point located off Gran Canaria (Canary Islands, eastern Atlantic) altered patterns in the abundance and assemblage structure of subtidal, soft-bottom, meiofauna. Samples were collected twice (May 2008 and January 2009) at 0, 15 and 30 m away from the brine discharge point, corresponding to a change in salinity from 45 to 36. Proximity to the brine discharge point affected overall meiofaunal abundances: lowest abundances were observed at 0 m (64.55 ± 39.86 ind 10 cm -2, mean ± SD) than at 15 (210.49 ± 121.01 ind 10 cm -2) and 30 m (361.88 ± 102.64 ind 10 cm -2) away from the brine discharge point. This pattern was particularly notable for the most conspicuous meiofaunal groups: nematodes and copepods, and meiofaunal assemblage structure also differed with varying proximity to the brine discharge point. Although multivariate techniques identified changes in salinity as a relevant driver of patterns in meiofaunal assemblage structure with varying proximity to the brine outfall, a shift in particle size composition between May 2008 and January 2009 also contributed to explain differences in meiofaunal abundances and assemblage structure with varying proximity to the brine discharge point. Hence, meiofauna can be considered a suitable tool to monitor environmental impacts derived from the discharge of hypersaline effluents on subtidal, soft-bottom, assemblages if potential confounding drivers, i.e. here temporal changes in particle size composition, are accounted for to avoid possible confusing interpretations.

  10. Survival of foodborne pathogens in natural cracked olive brines.

    Science.gov (United States)

    Medina, Eduardo; Romero-Gil, Verónica; Garrido-Fernández, Antonio; Arroyo-López, Francisco Noé

    2016-10-01

    This work reports the survival (challenge tests) of foodborne pathogen species (Escherichia coli, Staphylococcus aureus, Listeria monocytogenes, and Salmonella enterica) in Aloreña de Málaga table olive brines. The inhibitions were fit using a log-linear model with tail implemented in GInaFIT excel software. The olive brine had a considerable inhibitory effect on the pathogens. The residual (final) populations (Fp) after 24 h was below detection limit (olives for foodborne pathogenic microorganisms.

  11. Brines in Seepage Channels as Eluants for Subsurface Relict Biomolecules on Mars?

    Science.gov (United States)

    Wynn-Williams, David D.; Cabrol, Nathalie A.; Grin, Edmond A.; Haberle, Robert M.; Stoker, Carol R.

    2001-06-01

    Water, vital for life, not only maintains the integrity of structural and metabolic biomolecules, it also transports them in solution or colloidal suspension. Any flow of water through a dormant or fossilized microbial community elutes molecules that are potentially recognizable as biomarkers. We hypothesize that the surface seepage channels emanating from crater walls and cliffs in Mars Orbiter Camera images result from fluvial erosion of the regolith as low-temperature hypersaline brines. We propose that, if such flows passed through extensive subsurface catchments containing buried and fossilized remains of microbial communities from the wet Hesperian period of early Mars (~3.5 Ga ago), they would have eluted and concentrated relict biomolecules and delive red them to the surface. Life-supporting low-temperature hypersaline brines in Antarctic desert habitats provide a terrestrial analog for such a scenario. As in the Antarctic, salts would likely have accumulated in water-filled depressions on Mars by seasonal influx and evaporation. Liquid water in the Antarctic cold desert analogs occurs at -80°C in the interstices of shallow hypersaline soils and at -50°C in salt-saturated ponds. Similarly, hypersaline brines on Mars could have freezing points depressed below -50°C. The presence of hypersaline brines on Mars would have extended the amount of time during which life might have evolved. Phototrophic communities are especially important for the search for life because the distinctive structures and longevity of their pigments make excellent biomarkers. The surface seepage channels are therefore not only of geomorphological significance, but also provide potential repositories for biomolecules that could be accessed by landers.

  12. High catechin concentrations detected in Withania somnifera (ashwagandha by high performance liquid chromatography analysis

    Directory of Open Access Journals (Sweden)

    Sulaiman Siti

    2011-08-01

    Full Text Available Abstract Background Withania somnifera is an important medicinal plant traditionally used in the treatment of many diseases. The present study was carried out to characterize the phenolic acids, flavonoids and 1,1-diphenyl-2-picrylhydrazyl radical (DPPH scavenging activities in methanolic extracts of W. somnifera fruits, roots and leaves (WSFEt, WSREt and WSLEt. Methods WSFEt, WSREt and WSLEt was prepared by using 80% aqueous methanol and total polyphenols, flavonoids as well as DPPH radical scavenging activities were determined by spectrophotometric methods and phenolic acid profiles were determined by HPLC methods. Results High concentrations of both phenolics and flavonoids were detected in all parts of the plant with the former ranging between 17.80 ± 5.80 and 32.58 ± 3.16 mg/g (dry weight and the latter ranging between 15.49 ± 1.02 and 31.58 ± 5.07 mg/g. All of the three different plant parts showed strong DPPH radical scavenging activities (59.16 ± 1.20 to 91.84 ± 0.38%. Eight polyphenols (gallic, syringic, benzoic, p-coumaric and vanillic acids as well as catechin, kaempferol and naringenin have been identified by HPLC in parts of the plant as well. Among all the polyphenols, catechin was detected in the highest concentration (13.01 ± 8.93 to 30.61 ± 11.41 mg/g. Conclusion The results indicating that W. somnifera is a plant with strong therapeutic properties thus further supporting its traditional claims. All major parts of W. somnifera such as the roots, fruits and leaves provide potential benefits for human health because of its high content of polyphenols and antioxidant activities with the leaves containing the highest amounts of polyphenols specially catechin with strong antioxidant properties.

  13. Study and testing of direct contact heat exchangers for geothermal brines. Final report, June 1975--July 1976

    Energy Technology Data Exchange (ETDEWEB)

    Suratt, W.B.; Hart, G.K.

    1977-01-01

    The object of the work reported herein was to assess the technical and economic feasibility of preheating and evaporating a secondary fluid via direct contact with hot geothermal brine. The work covered a period of 12 months and included the design, construction, and testing of a unit which heats and vaporizes 10 gpm of isobutane by direct contact with 325/sup 0/F brine. The analytical and experimental efforts explored design and economic characteristics, including anticipated problem areas such as working fluid loss in the brine, production of a stable dispersion of the working fluid in brine, fluids separation, axial mixing and carry-over of water vapor with the working fluid. Isobutane was selected as the working fluid for tests primarily because of the favorable amount of net work produced per pound of geothermal brine and the low amount and cost of working fluid lost in the heat exchange process. The Elgin Spray Tower concept was selected for the preheater and boiler. The test apparatus includes a separate boiler and a separate preheater, each 6'' diameter by 6' high. Brine enters the top of each vessel and leaves the bottom. Isobutane enters the bottom of the preheater through a distributor plate to produce 0.15 inch diameter drops. The experimental unit operated with no major problems and demonstrated its hydraulic and thermal capabilities. Volumetric heat transfer coefficients obtained ranged up to 4000 BTU/hr /sup 0/F ft/sup 3/. Boiling heat transfer coefficients of as high as 17,000 BTU/hr /sup 0/F ft/sup 3/ were obtained with a design value of 10,000 BTU/hr /sup 0/F ft/sup 3/. Amount of isobutane in a 21 percent NaCl solution leaving the preheater was less than 40 ppM. A conceptual design and cost estimate was prepared for a direct contact heat exchange system sized for a 50 MW power plant.

  14. Silicate melt inclusion evidence for extreme pre-eruptive enrichment and post-eruptive depletion of lithium in silicic volcanic rocks of the western United States: implications for the origin of lithium-rich brines

    Science.gov (United States)

    Hofstra, Albert H.; Todorov, T.I.; Mercer, C.N.; Adams, D.T.; Marsh, E.E.

    2013-01-01

    To evaluate whether anatectic and/or highly fractionated lithophile element-enriched rhyolite tuffs deposited in arid lacustrine basins lose enough lithium during eruption, lithification, and weathering to generate significant Li brine resources, pre-eruptive melt compositions, preserved in inclusions, and the magnitude of post-eruptive Li depletions, evident in host rhyolites, were documented at six sites in the western United States. Each rhyolite is a member of the bimodal basalt-rhyolite assemblage associated with extensional tectonics that produced the Basin and Range province and Rio Grande rift, an evolving pattern of closed drainage basins, and geothermal energy or mineral resources. Results from the 0.8 Ma Bishop tuff (geothermal) in California, 1.3 to 1.6 Ma Cerro Toledo and Upper Bandelier tephra (geothermal) and 27.9 Ma Taylor Creek rhyolite (Sn) in New Mexico, 21.7 Ma Spor Mountain tuff (Be, U, F) and 24.6 Ma Pine Grove tuff (Mo) in Utah, and 27.6 Ma Hideaway Park tuff (Mo) in Colorado support the following conclusions. Melt inclusions in quartz phenocrysts from rhyolite tuffs associated with hydrothermal deposits of Sn, Mo, and Be are extremely enriched in Li (1,000s of ppm); those from Spor Mountain have the highest Li abundance yet recorded (max 5,200 ppm, median 3,750 ppm). Forty-five to 98% of the Li present in pre-eruptive magma was lost to the environment from these rhyolite tuffs. The amount of Li lost from the small volumes (1–10 km3) of Li-enriched rhyolite deposited in closed basins is sufficient to produce world-class Li brine resources. After each eruption, meteoric water leaches Li from tuff, which drains into playas, where it is concentrated by evaporation. The localized occurrence of Li-enriched rhyolites may explain why brines in arid lacustrine basins seldom have economic concentrations of Li. Considering that hydrothermal deposits of Sn, Mo, Be, U, and F may indicate potential for Li brines in nearby basins, we surmise that the

  15. In situ refractometry for concentration measurements in refrigeration systems

    Energy Technology Data Exchange (ETDEWEB)

    Newell, T.A. [Univ. of Illinois, Urbana, IL (United States). Dept. of Mechanical and Industrial Engineering

    1997-12-31

    An in situ refractometer was developed that is capable of measuring both the concentrations of oil in refrigerants, and the concentrations of aqueous coolant brines. A description of the technique, and example data are presented for R-134a/PAG oil, aqueous ethylene glycol, and aqueous propylene glycol solutions. The R-134a/PAG oil sensor data show a measurement sensitivity of less than 0.1% oil in the refrigerant, although error between data sets shows an uncertainty of approximately {+-}0.8%. Ethylene glycol and propylene glycol data show high signal level variations due to the large variation of the index of refraction between water and the glycols.

  16. High-Efficiency Solar Thermal Vacuum Demonstration Completed for Refractive Secondary Concentrator

    Science.gov (United States)

    Wong, Wayne A.

    2001-01-01

    Common to many of the space applications that utilize solar thermal energy--such as electric power conversion, thermal propulsion, and furnaces--is a need for highly efficient, solar concentration systems. An effort is underway at the NASA Glenn Research Center to develop the refractive secondary concentrator, which uses refraction and total internal reflection to efficiently concentrate and direct solar energy. When used in combination with advanced lightweight primary concentrators, the refractive secondary concentrator enables very high system concentration ratios (10,000 to 1) and very high temperatures (>2000 K). The innovative refractive secondary concentrator offers significant advantages over all other types of secondary concentrators. The refractive secondary offers the highest throughput efficiency, provides for flux tailoring, requires no active cooling, relaxes the pointing and tracking requirements of the primary concentrator, and enables very high system concentration ratios. This technology has broad applicability to any system that requires the conversion of solar energy to heat. Glenn initiated the development of the refractive secondary concentrator in support of Shooting Star, a solar thermal propulsion flight experiment, and continued the development in support of Space Solar Power.

  17. The Effect of Alkaline and Polymer Additives on Phase Behaviour of Surfactant-Oil-Brine System At High Salinity Conditions Effet des additifs alcalins et polymères sur le comportement des phases d'un système tensioactif-pétrole-saumure dans des conditions de forte salinité

    Directory of Open Access Journals (Sweden)

    Sayyouh M. H.

    2006-11-01

    Full Text Available This paper deals with the effect of alkali and polymer on the phase behavior of some available surfactants (Petrostep HMW - Safaniya crude oil-brine system and the phase relations were obtained after equilibrium at 25 and 70°C. It was found that the miscibility increases when using NaOH and with increasing concentration from 0. 5 to 1. 0% for reservoir salinity of 23% NaCl. Increasing NaCl concentration from 3. 84 to 23% decreases the system miscibility. Temperature increase and using of isopropyl alcohol decreases miscibility. Presence of polymer improves the miscibility on the water-rich side and decreases the miscibility on the oil-rich side. Cet article traite des effets des alcalis et des polymères sur l'équilibre des phases de certains systèmes disponibles combinant tensioactifs (Petrostep HMW, brut de Safaniya et saumure, et des rapports de phase obtenus après mise en équilibre à 25 et 70°C. On a constaté que la miscibilité augmente en cas d'utilisation de NaOH et avec une concentration croissante de 0,5 à 1,0 % pour une salinité du réservoir de 23 % NaCI. L'augmentation de la concentration de NaCI, de 3,84 à 23%, diminue la miscibilité du système. L'augmentation de la température et l'utilisation d'alcool isopropylique diminuent la miscibilité. La présence de polymère améliore la miscibilité pour la phase riche en eau et la diminue pour la phase riche en pétrole.

  18. Toxicity testing of restorative dental materials using brine shrimp larvae (Artemia salina).

    Science.gov (United States)

    Milhem, Manar M; Al-Hiyasat, Ahmad S; Darmani, Homa

    2008-01-01

    This study investigated the effect of extracts of different composites, glass ionomer cement (GIC)s and compomers on the viability of brine shrimp larvae. Ethanolic extracts of four dental composites (Z-100; Solitaire 2; Filtek P60 and Synergy), a conventional GIC (Ketac-Fil), a resin-modified glass ionomer cement (Vitremer), two compomers (F2000; Dyract AP), and a flowable compomer (Dyract Flow) were prepared from each material. Following evaporation of the ethanol, the extracts were resuspended in distilled water, which was then used to test the effects on the viability of brine shrimp larvae. For the composites, the extract of Synergy was the least toxic (88% viability) followed by the extracts of Solitaire 2, Z100 and P60 (75%, 67.5% and 50% viability, respectively). One-way ANOVA revealed highly significant differences between the resin composite materials (pbrine shrimp larvae followed by GICs and then composites.

  19. Efficient acetylation of primary amines and amino acids in environmentally benign brine solution using acetyl chloride

    Indian Academy of Sciences (India)

    Kaushik Basu; Suchandra Chakraborty; Achintya Kumar Sarkar; Chandan Saha

    2013-05-01

    Acetyl chloride is one of the most commonly available and cheap acylating agent but its high reactivity and concomitant instability in water precludes its use to carry out acetylation in aqueous medium. The present methodology illustrates the efficient acetylation of primary amines and amino acids in brine solution by means of acetyl chloride under weakly basic condition in the presence of sodium acetate and/or triethyl amine followed by trituration with aqueous saturated bicarbonate solution. This effort represents the first efficient use of this most reactive but cheap acetylating agent to acetylate amines in excellent yields in aqueous medium. This is a potentially useful green chemical transformation where reaction takes place in environment-friendly brine solution leading to easy work-up and isolation of the amide derivatives. Mechanistic rationale of this methodology is also important.

  20. High-sensitivity in situ QCLAS-based ammonia concentration sensor for high-temperature applications

    Science.gov (United States)

    Peng, W. Y.; Sur, R.; Strand, C. L.; Spearrin, R. M.; Jeffries, J. B.; Hanson, R. K.

    2016-07-01

    A novel quantum cascade laser (QCL) absorption sensor is presented for high-sensitivity in situ measurements of ammonia (hbox {NH}_3) in high-temperature environments, using scanned wavelength modulation spectroscopy (WMS) with first-harmonic-normalized second-harmonic detection (scanned WMS-2 f/1 f) to neutralize the effect of non-absorption losses in the harsh environment. The sensor utilized the sQ(9,9) transition of the fundamental symmetric stretch band of hbox {NH}_3 at 10.39 {\\upmu }hbox {m} and was sinusoidally modulated at 10 kHz and scanned across the peak of the absorption feature at 50 Hz, leading to a detection bandwidth of 100 Hz. A novel technique was used to select an optimal WMS modulation depth parameter that reduced the sensor's sensitivity to spectral interference from hbox {H}_2hbox {O} and hbox {CO}_2 without significantly sacrificing signal-to-noise ratio. The sensor performance was validated by measuring known concentrations of hbox {NH}_3 in a flowing gas cell. The sensor was then demonstrated in a laboratory-scale methane-air burner seeded with hbox {NH}_3, achieving a demonstrated detection limit of 2.8 ± 0.26 ppm hbox {NH}_3 by mole at a path length of 179 cm, equivalence ratio of 0.6, pressure of 1 atm, and temperatures of up to 600 K.

  1. Molecularly characterized solvent extracts and saponins from Polygonum hydropiper L show high anti-angiogenic, anti-tumor, brine shrimp and fibroblast NIH/3T3 cell line cytotoxicity

    Directory of Open Access Journals (Sweden)

    Muhammad eAyaz

    2016-03-01

    Full Text Available Polygonum hydropiper is used as anti-cancer and anti-rheumatic agent in folk medicine. This study was designed to investigate the anti-angiogenic, anti-tumor and cytotoxic potentials of different solvent extracts and isolated saponins. Samples were analyzed using GC, GC-MS to identify major and bioactive compounds. Quantitation of antiangiogenesis for the plant's samples including methanolic extract (Ph.Cr, its subsequent fractions; n-hexane (Ph.Hex, chloroform (Ph.Chf, ethyl acetate (Ph.EtAc, n-Butanol (Ph.Bt, aqueous (Ph.Aq, saponins (Ph.Sp were performed using the chick embryo chorioallantoic membrane (CAM assay. Potato disc anti-tumor assay was performed on Agrobacterium tumefaciens containing tumor inducing plasmid. Cytotoxicity was performed on Artemia salina and mouse embryonic fibroblast NIH/3T3 cell line using brine shrimps and MTT cells viability assays. The GC-MS analysis of Ph.Cr, Ph.Hex, Ph.Chf, Ph.Bt and Ph.EtAc identified 126, 124, 153, 131 and 164 compounds respectively. In anti-angiogenic assay, Ph.Chf, Ph.Sp, Ph.EtAc and Ph.Cr exhibited highest activity with IC50 of 28.65, 19.21, 88.75 and 461.53 µg/ml respectively. In anti-tumor assay, Ph.Sp, Ph.Chf, Ph.EtAc and Ph.Cr were most potent with IC50 of 18.39, 73.81, 217.19 and 342.53 µg/ml respectively. In MTT cells viability assay, Ph.Chf, Ph.EtAc, Ph.Sp were most active causing 79.00, 72.50 and 71.50% cytotoxicity respectively at 1000 µg/ml with the LD50 of 140, 160 and 175 µg/ml respectively. In overall study, Ph.Chf and Ph.Sp have shown overwhelming results which signifies their potentials as sources of therapeutic agents against cancer.

  2. Enrichment of extremophilic exoelectrogens in microbial electrolysis cells using Red Sea brine pools as inocula

    KAUST Repository

    Shehab, Noura A.

    2017-05-03

    Applying microbial electrochemical technologies for the treatment of highly saline or thermophilic solutions is challenging due to the lack of proper inocula to enrich for efficient exoelectrogens. Brine pools from three different locations (Valdivia, Atlantis II and Kebrit) in the Red Sea were investigated as potential inocula sources for enriching exoelectrogens in microbial electrolysis cells (MECs) under thermophilic (70°C) and hypersaline (25% salinity) conditions. Of these, only the Valdivia brine pool produced high and consistent current 6.8 ± 2.1 A/m2-anode in MECs operated at a set anode potential of +0.2 V vs. Ag/AgCl (+0.405 V vs. standard hydrogen electrode). These results show that exoelectrogens are present in these extreme environments and can be used to startup MEC under thermophilic and hypersaline conditions. Bacteroides was enriched on the anode of the Valdivia MEC, but it was not detected in the open circuit voltage reactor seeded with the Valdivia brine pool.

  3. Vitamin C at high concentrations induces cytotoxicity in malignant melanoma but promotes tumor growth at low concentrations.

    Science.gov (United States)

    Yang, Guang; Yan, Yao; Ma, Younan; Yang, Yixin

    2017-08-01

    Vitamin C has been used in complementary and alternative medicine for cancers regardless of its ineffectiveness in clinical trials and the paradoxical effects antioxidants have on cancer. Vitamin C was found to induce cytotoxicity against cancers. However, the mechanisms of action have not been fully elucidated, and the effects of vitamin C on human malignant melanoma have not been examined. This study revealed that vitamin C at millimolar concentrations significantly reduced the cell viability as well as invasiveness, and induced apoptosis in human malignant melanoma cells. Vitamin C displayed stronger cytotoxicity against the Vemurafenib-resistance cell line A2058 compared with SK-MEL-28. In contrast, vitamin C at micromolar concentrations promoted cell growth, migration and cell cycle progression, and protected against mitochondrial stress. Vemurafenib paradoxically activated the RAS-RAF-MEK-ERK signaling pathway in the Vemurafenib-resistant A2058, however, vitamin C abolished the activations. Vitamin C displayed synergistic cytotoxicity with Vemurafenib against the Vemurafenib-resistant A2058. In vivo assay suggested that lower dosage (equivalent to 0.5 g/70 kg) of vitamin C administered orally increased the melanoma growth. Therefore, vitamin C may exert pro- or anti-melanoma effect depending on concentration. The combination of vitamin C at high dosage and Vemurafenib is promising in overcoming the action of drug resistance. © 2017 Wiley Periodicals, Inc.

  4. Linking near- and far-field hydrodynamic models for simulation of desalination plant brine discharges.

    Science.gov (United States)

    Botelho, D A; Barry, M E; Collecutt, G C; Brook, J; Wiltshire, D

    2013-01-01

    A desalination plant is proposed to be the major water supply to the Olympic Dam Expansion Mining project. Located in the Upper Spencer Gulf, South Australia, the site was chosen due to the existence of strong currents and their likely advantages in terms of mixing and dilution of discharged return water. A high-resolution hydrodynamic model (Estuary, Lake and Coastal Ocean Model, ELCOM) was constructed and, through a rigorous review process, was shown to reproduce the intricate details of the Spencer Gulf dynamics, including those characterising the discharge site. Notwithstanding this, it was found that deploying typically adopted 'direct insertion' techniques to simulate the brine discharge within the hydrodynamic model was problematic. Specifically, it was found that in this study the direct insertion technique delivered highly conservative brine dilution predictions in and around the proposed site, and that these were grid and time-step dependent. To improve the predictive capability, a strategy to link validated computational fluid dynamics (CFD) predictions to hydrodynamic simulations was devised. In this strategy, environmental conditions from ELCOM were used to produce boundary conditions for execution of a suite of CFD simulations. In turn, the CFD simulations provided the brine dilutions and flow rates to be applied in ELCOM. In order to conserve mass in a system-wide sense, artificial salt sinks were introduced to the ELCOM model such that salt quantities were conserved. As a result of this process, ELCOM predictions were naturally very similar to CFD predictions near the diffuser, whilst at the same time they produced an area of influence (further afield) comparable to direct insertion methods. It was concluded that the linkage of the models, in comparison to direct insertion methods, constituted a more realistic and defensible alternative to predict the far-field dispersion of outfall discharges, particularly with regards to the estimation of brine

  5. Experimental investigation of CO{sub 2}-brine-rock interactions at elevated temperature and pressure: Implications for CO{sub 2} sequestration in deep-saline aquifers

    Energy Technology Data Exchange (ETDEWEB)

    Rosenbauer, Robert J.; Koksalan, Tamer; Palandri, James L. [U.S. Geological Survey, 345 Middlefield Road, Menlo Park, CA 94025 (United States)

    2005-10-15

    Deep-saline aquifers are potential repositories for excess CO{sub 2}, currently being emitted to the atmosphere from anthropogenic activities, but the reactivity of supercritical CO{sub 2} with host aquifer fluids and formation minerals needs to be understood. Experiments reacting supercritical CO{sub 2} with natural and synthetic brines in the presence and absence of limestone and plagioclase-rich arkosic sandstone showed that the reaction of CO{sub 2}-saturated brine with limestone results in compositional, mineralogical, and porosity changes in the aquifer fluid and rock that are dependent on initial brine composition, especially dissolved calcium and sulfate. Experiments reacting CO{sub 2}-saturated, low-sulfate brine with limestone dissolved 10% of the original calcite and increased rock porosity by 2.6%. Experiments reacting high-sulfate brine with limestone, both in the presence and absence of supercritical CO{sub 2}, were characterized by the precipitation of anhydrite, dolomitization of the limestone, and a final decrease in porosity of 4.5%. However, based on favorable initial porosity changes of about 15% due to the dissolution of calcite, the combination of CO{sub 2} co-injection with other mitigation strategies might help alleviate some of the well-bore scale and formation-plugging problems near the injection zone of a brine disposal well in Paradox Valley, Colorado, as well as provide a repository for CO{sub 2}. Experiments showed that the solubility of CO{sub 2} is enhanced in brine in the presence of limestone by 9% at 25 {sup o}C and 6% at 120 {sup o}C and 200 bar relative to the brine itself. The solubility of CO{sub 2} is enhanced also in brine in the presence of arkosic sandstone by 5% at 120 {sup o}C and 300 bar. The storage of CO{sub 2} in limestone aquifers is limited to only ionic and hydraulic trapping. However, brine reacted with supercritical CO{sub 2} and arkose yielded fixation and sequestration of CO{sub 2} in carbonate mineral phases

  6. Cytotoxic and apoptotic evaluations of marine bacteria isolated from brine-seawater interface of the Red Sea.

    KAUST Repository

    Sagar, Sunil

    2013-02-06

    High salinity and temperature combined with presence of heavy metals and low oxygen renders deep-sea anoxic brines of the Red Sea as one of the most extreme environments on Earth. The ability to adapt and survive in these extreme environments makes inhabiting bacteria interesting candidates for the search of novel bioactive molecules.

  7. Kinetics of nitrate and perchlorate reduction in ion exchange brine using the membrane biofilm reactor (MBfR)

    Science.gov (United States)

    Several sources of bacterial inocula were tested for their ability to reduce nitrate and perchlorate in synthetic ion-exchange spent brine (3-4.5% salinity) using a hydrogen-based membrane biofilm reactor (MBfR). Nitrate and perchlorate removal fluxes reached as high as 5.4 g N ...

  8. Complexation of Nd(III) with tetraborate ion and its effect on actinide (III) solubility in WIPP brine

    Energy Technology Data Exchange (ETDEWEB)

    Borkowski, Marian [Los Alamos National Laboratory; Richmann, Michael K [Los Alamos National Laboratory; Reed, Donald T [Los Alamos National Laboratory; Yongliang, Xiong [SNL

    2010-01-01

    The potential importance of tetraborate complexation on lanthanide(III) and actinide(III) solubility is recognized in the literature but a systematic study of f-element complexation has not been performed. In neodymium solubility studies in WIPP brines, the carbonate complexation effect is not observed since tetraborate ions form a moderately strong complex with neodymium(III). The existence of these tetraborate complexes was established for low and high ionic strength solutions. Changes in neodymium(III) concentrations in undersaturation experiments were used to determine the neodymium with tetraborate stability constants as a function of NaCl ionic strength. As very low Nd(III) concentrations have to be measured, it was necessary to use an extraction pre-concentration step combined with ICP-MS analysis to extend the detection limit by a factor of 50. The determined Nd(III) with borate stability constants at infinite dilution and 25 C are equal to log {beta}{sub 1} = 4.55 {+-} 0.06 using the SIT approach, equal to log {beta}{sub 1} = 4.99 {+-} 0.30 using the Pitzer approach, with an apparent log {beta}{sub 1} = 4.06 {+-} 0.15 (in molal units) at I = 5.6 m NaCl. Pitzer ion-interaction parameters for neodymium with tetraborate and SIT interaction coefficients were also determined and reported.

  9. Complexation of Nd(III) with tetraborate ion and its effect on actinide(III) solubility in WIPP brine

    Energy Technology Data Exchange (ETDEWEB)

    Borkowski, M.; Richmann, M.; Reed, D.T. [Earth and Environmental Sciences Div., Los Alamos National Lab., Carlsbad Operations, NM (United States); Xiong, Y. [Sandia National Labs., Carlsbad Program Group, Carlsbad, NM (United States)

    2010-07-01

    The potential importance of tetraborate complexation on lanthanide(III) and actinide(III) solubility is recognized in the literature but a systematic study of f-element complexation has not been performed. In neodymium solubility studies in WIPP brines, the carbonate complexation effect is not observed since tetraborate ions form a moderately strong complex with neodymium(III). The existence of these tetraborate complexes was established for low and high ionic strength solutions. Changes in neodymium(III) concentrations in undersaturation experiments were used to determine the neodymium with tetraborate stability constants as a function of NaCl ionic strength. As very low Nd(III) concentrations have to be measured, it was necessary to use an extraction pre-concentration step combined with ICP-MS analysis to extend the detection limit by a factor of 50. The determined Nd(III) with borate stability constants at infinite dilution and 25 C are equal to log {beta}{sub 1} = 4.55 {+-} 0.06 using the SIT approach, equal to log {beta}{sub 1} = 4.99 {+-} 0.30 using the Pitzer approach, with an apparent log {beta}{sub 1} = 4.06 {+-} 0.15 (in molal units) at I = 5.6 m NaCl. Pitzer ion-interaction parameters for neodymium with tetraborate and SIT interaction coefficients were also determined and reported. (orig.)

  10. Hydrological and Chemical Assessment of Groundwater Flow and Quality in Costal Brine Aquifers of Laizhou Bay, China

    Science.gov (United States)

    Zhang, Xiaoying; Hu, Bill X.; Miao, Jinjie

    2016-04-01

    In geological time, seawater had been intruded groundwater several times since Late Pleistocene in the coastal area of Laizhou Bay, china. This unique phenomenon caused freshwater and brine water interbedded each other in the aquifers and forged Laizhou Bay became a multiple sources dynamic coastal area. In the last two decades, massive exploitation of fresh groundwater and brine water has significantly increased seawater intrusion and strengthened mixture of brine water and freshwater in the coastal area, which threatens local groundwater resources and severely impacts local ecological geo-environment. In this study, the hydrological and chemical (HC) process was studied according to the monitoring wells and chemical ionic constituents. The groundwater level continuously decreasing rather than showing a typical seasonal variation in areas close to the depression cone. A groundwater divide was formed along Yingli-Houzhen-Yangzi accounted for the exploitation of fresh water in the south and brine extraction in the north. This divide prevented the saltwater intrusion to fresh groundwater further south in study area. The results also showed that during concentration process, a series of complex reactions including water chemistry metamorphic role and evolution took place, such as mineral precipitation, cation ion exchange, dedolomitization and silicate alteration, etc. This work highlighted hydrological-chemical coupling process and provided a better insight into hydrogeological system.

  11. 卤水中氧化镁提取工艺研究%Brine Preparation of Magnesium Oxide Process

    Institute of Scientific and Technical Information of China (English)

    向群; 王蓉

    2012-01-01

    The paper asks about extracting magnesium oxide from the brine. Brine-soda method to the purification of brine by adding sodium carbonate, the preparation of basic magnesium carbonate, basic magnesium carbonate magnesium oxide after calcination. The experimental results show that the Barium chloride concentration of 0.13 mol/L, and the water bath temperature of 40 ℃, feed rate the 5 mL/min, aging time for lh brine purification best. The ratio of raw materials to 110 %, the reaction temperature is 60℃, reaction time was 30 min, and Magnesium oxide yield.%采用卤水-纯碱法,向经过净化的卤水中加入碳酸钠,制取碱式碳酸镁,经过煅烧得到氧化镁。实验结果表明:反应浓度O.13mol/L、反应温度40℃、加科速度5mL/min、陈化时间1h时卤水的净化效果较好。原料配比110%、反应温度60℃、反应时间30min时氧化镁的收率较好。

  12. Quantitation of low concentrations of polysorbates in high protein concentration formulations by solid phase extraction and cobalt-thiocyanate derivatization.

    Science.gov (United States)

    Kim, Justin; Qiu, Jinshu

    2014-01-02

    A spectrophotometric method was developed to quantify low polysorbate (PS) levels in biopharmaceutical formulations containing high protein concentrations. In the method, Oasis HLB solid phase extraction (SPE) cartridge was used to extract PS from high protein concentration formulations. After loading a sample, the cartridge was washed with 4M guanidine HCl and 10% (v/v) methanol, and the retained PS was eluted by acetonitrile. Following the evaporation of acetonitrile, aqueous cobalt-thiocyanate reagent was added to react with the polyoxyethylene oxide chain of polysorbates to form a blue colored PS-cobaltothiocyante complex. This colored complex was then extracted into methylene chloride and measured spectrophotometrically at 620 nm. The method performance was evaluated on three products containing 30-40 mg L(-1) PS-20 and PS-80 in ≤70 g L(-1) protein formulations. The method was specific (no matrix interference identified in three types of protein formulations), sensitive (quantitation limit of 10 mg L(-1) PS) and robust with good precision (relative standard deviation ≤6.4%) and accuracy (spike recoveries from 95% to 101%). The linear range of the method for both PS-20 and PS-80 was 10 to 80 mg L(-1) PS. By diluting samples with 6M guanidine HCl and/or using different methylene chloride volumes to extract the colored complexes of standards and samples, the method could accurately and precisely quantify 40 mg L(-1) PS in up to 300 g L(-1) protein formulations.

  13. Brine Extraction and Treatment Strategies to Enhance Pressure Management and Control of CO2 Plumes in Deep Geologic Formations

    Energy Technology Data Exchange (ETDEWEB)

    Okwen, Roland [Univ. of Illinois, Champaign, IL (United States). Prairie Research Inst.; Frailey, Scott [Univ. of Illinois, Champaign, IL (United States). Prairie Research Inst.; Dastgheib, Seyed [Univ. of Illinois, Champaign, IL (United States). Prairie Research Inst.

    2017-06-14

    The overall goal of the this project is to develop and validate pressure management and carbon dioxide (CO2) plume control strategies that can address technical and economic barriers to commercial deployment of CO2 storage technologies, based on computational and field demonstration work at the Archer Daniels Midland Company (ADM) facility where the Illinois Basin–Decatur Project (IBDP) and the Illinois-Industrial Carbon Capture and Storage (IL-ICCS) projects are located. To accomplish the overall goal, the ISGS designed a brine extraction storage test (BEST) that could be completed in two phases. The goal of BEST Phase I was to evaluate the feasibilities of extraction well(s) placement, the brine extraction to CO2 injection rate ratio, extraction well completion, and brine treatment and handling. The goal of BEST Phase II would be to validate the brine extraction and treatment options deemed feasible in Phase I by (1) demonstrating the efficacy of brine extraction (BE) in managing pressure (i.e., formation) and the CO2 plume, and (2) demonstrating treatment of extracted brine with high total dissolved solids (TDS; >200,000 mg/L) using multiple advanced treatment technologies. This report details work done in Phase I. Several brine extraction and treatment scenarios were tested, simulated, and analyzed for their effectiveness in extracting brine. Initially a vertical well was studied; however, geologic modeling, reservoir modeling, and the existing facility and wellbore infrastructure dictated that the location of a vertical brine extraction well was limited to an area with no existing monitoring wells and where the well would be in relative proximity to an existing CO2 plume. Consequently, a vertical well was excluded, and a horizontal brine extraction well placed above the existing CO2 plume near two existing wells was studied. The horizontal well option allows the project to leverage the

  14. Investigation of oil injection into brine for the strategic petroleum reserve : hydrodynamics experiments with simulant liquids.

    Energy Technology Data Exchange (ETDEWEB)

    Castaneda, Jaime N.; Shollenberger, Kim Ann (California Polytechnic State University, San Luis Obispo, CA); Torczynski, John Robert; Cote, Raymond O.; Barney, Jeremy; O' Hern, Timothy John

    2003-10-01

    oil-droplet residence time in the brine. Reductions of these quantities would inhibit emulsion formation by limiting the contact between the oil and the brine. Videos of this flow were recorded for scaled flow rates that bracket the equivalent pumping rates in an SPR cavern. Image-processing analyses were performed to quantify the penetration depth of the oil jet, the width of the jet, and the deflection of the interface. The measured penetration depths are shallow, as predicted by penetration-depth models, in agreement with the assumption that the flow is buoyancy-dominated, rather than momentum-dominated. The turbulent penetration depth model provided a good estimate of the measured values for the 1-inch injection tube but overpredicted the penetration depth for the 1/2-inch injection tube. Adding a virtual origin term would improve the prediction for the 1/2-inch tube for low to nominal injection flow rates but could not capture the rollover seen at high injection flow rates. As expected, the J-tube yielded a much narrower plume because the flow was directed upward, unlike the downward-oriented straight-tube cases where the plume had to reverse direction, leading to a much wider effective plume area. Larger surface deflections were caused by the narrower plume emitted from the J-tube. Although velocity was not measured in these experiments, the video data showed that the J-tube plume was clearly faster than those emitted from the downward-oriented tubes. These results indicate that oil injection tube modifications could inhibit emulsion formation by reducing the amount of contact (both time and area) between the oil and the brine. Future studies will employ crude oil, saturated brine, and interfacial solids (sludge) from actual SPR caverns.

  15. Determining CO2-brine relative permeability and capillary pressure simultaneously: an insight to capillary entrance and end effects

    Science.gov (United States)

    Chen, X.; Kianinejad, A.; DiCarlo, D. A.

    2014-12-01

    CO2-brine relative permeability relations are important parameters in modeling scenarios such as CO2 sequestration in saline aquifers and CO2 enhanced recovery in oil reservoir. Many steady-state experimental studies on CO2-brine relative permeability showed that the CO2-brine relative permeability differs greatly from typical oil-brine relative permeability. Particularly, they reported a very small endpoint CO2 relative permeability of 0.1~0.2 at a relative high residual water saturation of 0.4~0.6. In this study, we hypothesize the measured low endpoint CO2 relative permeability in previous studies was an experimental artifact that is primary due to low CO2 viscosity. We conducted steady-state CO2 drainage experiments by co-injecting equlibrated CO2 and brine into a long (60.8 cm) and low permeability (116-mD) Berea sandstone core at 20 °C and 1500 psi. During every experiment, both the overall pressure drop across the core and the pressure drops of the five independent and continuous sections of the core were monitored. The in-situ saturation was measured with a medical X-ray Computed Tomography (CT) scanner. In the center three sections where saturation was uniform, we determined the relative permeability to both brine and CO2 phases. In the entrance and exit sections, both measured pressure gradients and saturation were non-uniform. To cope with this, we make several self-consistent assumptions that reveal the nature of capillary entrance and effect in steady-state two-phase core flooding experiments. Based on these assumptions we determined the relative permeability to CO2 and CO2-brine capillary pressure simultaneously using measured pressure drops. We found: (1) a much higher endpoint CO2 relative permeability of 0.58 at a water saturation of 48%, (2) the entrance region with non-uniform saturation expanded CO2 relative permeability data to much lower water saturation, (3) the determined CO2-brine capillary pressure curve is self-consistent and matches

  16. Design, Fabrication and Test of a High Efficiency Refractive Secondary Concentrator for Solar Applications

    Science.gov (United States)

    Wong, Wayne A.; Geng, Steven M.; Castle, Charles H.; Macosko, Robert P.

    2000-01-01

    Common to many of the space applications that utilize solar thermal energy such as electric power conversion, thermal propulsion, and furnaces, is a need for highly efficient, solar concentration systems. An effort is underway to develop the refractive secondary concentrator, which uses refraction and total internal reflection to efficiently concentrate and direct solar energy. When used in combination with advanced primary concentrators, the refractive secondary concentrator enables very high system concentration ratios (10,000 to 1) and very high temperatures (greater than 2000 K). Presented is an overview of the effort at the NASA Glenn Research Center to evaluate the performance of a prototype single crystal sapphire refractive secondary concentrator and to compare the performance with analytical models. The effort involves the design and fabrication of a secondary concentrator, design and fabrication of a calorimeter and its support hardware, calibration of the calorimeter, testing of the secondary concentrator in NASA Glenn's Tank 6 solar thermal vacuum facility, and comparing the test results with predictions. Test results indicate an average throughput efficiency of 87%. It is anticipated that reduction of a known reflection loss with an anti-reflective coating would result in a secondary concentrator throughput efficiency of approximately 93%.

  17. Genomic and Transcriptomic Evidence for Carbohydrate Consumption among Microorganisms in a Cold Seep Brine Pool

    KAUST Repository

    Zhang, Weipeng

    2016-11-15

    The detailed lifestyle of microorganisms in deep-sea brine environments remains largely unexplored. Using a carefully calibrated genome binning approach, we reconstructed partial to nearly-complete genomes of 51 microorganisms in biofilms from the Thuwal cold seep brine pool of the Red Sea. The recovered metagenome-assembled genomes (MAGs) belong to six different phyla: Actinobacteria, Proteobacteria, Candidatus Cloacimonetes, Candidatus Marinimicrobia, Bathyarchaeota, and Thaumarchaeota. By comparison with close relatives of these microorganisms, we identified a number of unique genes associated with organic carbon metabolism and energy generation. These genes included various glycoside hydrolases, nitrate and sulfate reductases, putative bacterial microcompartment biosynthetic clusters (BMC), and F420H2 dehydrogenases. Phylogenetic analysis suggested that the acquisition of these genes probably occurred through horizontal gene transfer (HGT). Metatranscriptomics illustrated that glycoside hydrolases are among the most highly expressed genes. Our results suggest that the microbial inhabitants are well adapted to this brine environment, and anaerobic carbohydrate consumption mediated by glycoside hydrolases and electron transport systems (ETSs) is a dominant process performed by microorganisms from various phyla within this ecosystem.

  18. Core-scale electrical resistivity tomography (ERT) monitoring of CO2-brine mixture in Fontainebleau sandstone

    Science.gov (United States)

    Bosch, David; Ledo, Juanjo; Queralt, Pilar; Bellmunt, Fabian; Luquot, Linda; Gouze, Philippe

    2016-07-01

    The main goal of the monitoring stage of Carbon Capture and Storage (CCS) is to obtain an accurate estimation of the subsurface CO2 accumulation and to detect any possible leakage. Laboratory experiments are necessary to investigate the small scale processes governing the CO2-brine-rock interaction. They also provide a means to calibrate the results coming from field scale geophysical methods. In this work we set up an experimental system which is able to perform Electrical Resistivity Tomography (ERT) measurements on centimeter-scale rock samples at various P-T conditions. We present the results of two new experiments related to CO2 monitoring, performed on a cylindrical (4 × 8 cm) Fontainebleau rock sample. In the first one, we have quantified the CO2 saturation at different volume fractions, representing zones from a deep saline aquifer with varying degrees of saturation. In the second one, we have monitored and quantified the effect of CO2 dissolution in the brine at a pressure of 40 bar during eight days, emulating the invasion of CO2 into a shallow aquifer. Results highlight the importance of accounting for the contribution of surface conductivity in highly CO2-saturated regions, even in clay-free rocks, and also for brine conductivity variation due to CO2 dissolution. Ignoring any of these effects will end up in a CO2 saturation underestimation. We present a modified CO2 saturation equation to account for these two influences.

  19. USE OF REJECT BRINE FROM DESALINATION ON DIFFERENT DEVELOPMENT STAGES OF HYDROPONIC LETTUCE

    Directory of Open Access Journals (Sweden)

    NILDO DA SILVA DIAS

    2011-01-01

    Full Text Available In order to evaluated the impact of the high salinity reject brine from reverse osmosis desalination on hydroponics lettuce cultivated in greenhouse an investigation was carried out in Mossoro, Northeast of Brazil (5º11'S, 37º20'O and 18m above sea. Two lettuce cultivars ('Verônica' and 'Babá de verão' were cultivated with a basic nutrient solution with 1.1 dS m-1 (control during the crop cycle (1-28 days after transplanting - DAT - T0 and with basic nutrient solution containing 50% of the reject water from desalinization with 4.8 dS m-1 exposed during 1-7, 21-28, 7-14 e 1-28 DAT (T1, T2, T3 and T4, respectively. The addition of 50% of brine reject from desalination into the hydroponic nutrient solution allows grow only 'Verônica' lettuce with no reduction in fresh biomass. This lettuce cultivar shows to be more tolerant to salinity for all exposure time with reject brine in the nutrition solution, despite the fact that 'Babá de Verão' cultivar is more productive.

  20. Toxicоlogical evaluation of the plant products using Brine Shrimp (Artemia salina L. model

    Directory of Open Access Journals (Sweden)

    Меntor R. Hamidi

    2014-04-01

    Full Text Available Many natural products could serve as the starting point in the development of modern medicines because of their numerous biological and pharmacological activities. However, some of them are known to carry toxicological properties as well. In order to achieve a safe treatment with plant products, numerous research studies have recently been focused on both pharmacology and toxicity of medicinal plants. Moreover, these studies employed efforts for alternative biological assays. Brine Shrimp Lethality Assay is the most convenient system for monitoring biological activities of various plant species. This method is very useful for preliminary assessment of toxicity of the plant extracts. Rapidness, simplicity and low requirements are several advantages of this assay. However, several conditions need to be completed, especially in the means of standardized experimental conditions (temperature, pH of the medium, salinity, aeration and light. The toxicity of herbal extracts using this assay has been determined in a concentration range of 10, 100 and 1000 µg/ml of the examined herbal extract. Most toxicity studies which use the Brine Shrimp Lethality Assay determine the toxicity after 24 hours of exposure to the tested sample. The median lethal concentration (LC50 of the test samples is obtained by a plot of percentage of the dead shrimps against the logarithm of the sample concentration. LC50 values are estimated using a probit regression analysis and compared with either Meyer’s or Clarkson’s toxicity criteria. Furthermore, the positive correlation between Meyer’s toxicity scale for Artemia salina and Gosselin, Smith and Hodge’s toxicity scale for higher animal models confirmed that the Brine Shrimp Lethality Assay is an excellent predictive tool for the toxic potential of plant extracts in humans.

  1. Redox states of underground brine system along the southern coast of the Laizhou Bay

    Institute of Scientific and Technical Information of China (English)

    JIANG Xueyan; YU Zhigang; NING Jinsong; CHEN Hongtao; MI Tiezhu

    2008-01-01

    Underground brine samples were collected along the southern coast of the Laizhou Bay,Shangdong,China in two field investigations in 2003.The brines are confined in the Quaternary sediment and underwent a series of geochemical changes.The redox states of these brines were assessed qualitatively based on the measurements of Eh and redox-sensitive species such as DO,NO NO3,Mn2+,Fe2+,SO2-4 in the brines.The redox condition of the underground brine is anoxic,and the redox reactions that controlled the redox potential of brines should be Fe (Ⅲ) reduction and sulfate reduction.

  2. Novel DDR Processing of Corn Stover Achieves High Monomeric Sugar Concentrations from Enzymatic Hydrolysis (230 g/L) and High Ethanol Concentration (10% v/v) During Fermentation

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Xiaowen; Jennings, Ed; Shekiro, Joe; Kuhn, Erik M.; O' Brien, Marykate; Wang, Wei; Schell, Daniel J.; Himmel, Mike; Elander, Richard T.; Tucker, Melvin P.

    2015-04-03

    Distilling and purifying ethanol, butanol, and other products from second and later generation lignocellulosic biorefineries adds significant capital and operating cost for biofuels production. The energy costs associated with distillation affects plant gate and life cycle analysis costs. Lower titers in fermentation due to lower sugar concentrations from pretreatment increase both energy and production costs. In addition, higher titers decrease the volumes required for enzymatic hydrolysis and fermentation vessels. Therefore, increasing biofuels titers has been a research focus in renewable biofuels production for several decades. In this work, we achieved over 200 g/L of monomeric sugars after high solids enzymatic hydrolysis using the novel deacetylation and disc refining (DDR) process on corn stover. The high sugar concentrations and low chemical inhibitor concentrations from the DDR process allowed ethanol titers as high as 82 g/L in 22 hours, which translates into approximately 10 vol% ethanol. To our knowledge, this is the first time that 10 vol% ethanol in fermentation derived from corn stover without any sugar concentration or purification steps has been reported. Techno-economic analysis shows the higher titer ethanol achieved from the DDR process could significantly reduce the minimum ethanol selling price from cellulosic biomass.

  3. Thermodynamically consistent description of the hydrodynamics of free surfaces covered by insoluble surfactants of high concentration

    OpenAIRE

    Thiele, Uwe; Archer, Andrew J.; Plapp, Mathis

    2012-01-01

    In this paper we propose several models that describe the dynamics of liquid films which are covered by a high concentration layer of insoluble surfactant. First, we briefly review the 'classical' hydrodynamic form of the coupled evolution equations for the film height and surfactant concentration that are well established for small concentrations. Then we re-formulate the basic model as a gradient dynamics based on an underlying free energy functional that accounts for wettability and capill...

  4. Incomplete Ion Dissociation Underlies the Weakened Attraction between DNA Helices at High Spermidine Concentrations

    OpenAIRE

    Yang,Jie; Rau, Donald C

    2005-01-01

    We have investigated the salt sensitivity of the hexagonal-to-cholesteric phase transition of spermidine-condensed DNA. This transition precedes the resolubilization of precipitated DNA that occurs at high spermidine concentration. The sensitivity of the critical spermidine concentration at the transition point to the anion species and the NaCl concentration indicates that ion pairing of this trivalent ion underlies this unusual transition. Osmotic pressure measurements of spermidine salt sol...

  5. Forsterite dissolution rates in Mg-sulfate-rich Mars-analog brines and implications of the aqueous history of Mars

    Science.gov (United States)

    Albright Olsen, Amanda; Hausrath, Elisabeth M.; Rimstidt, J. Donald

    2015-03-01

    High salinity brines, although rare on Earth's surface, may have been important in the geologic history of Mars. Increasing evidence suggests the importance of liquid brines in multiple locations on Mars. In order to interpret the effect of high ionic strength brines on olivine dissolution, which is widely present on Mars, 47 new batch reactor experiments combined with 35 results from a previous study conducted at 25°C from 1 sodium sulfate, magnesium nitrate, and potassium nitrate solutions with ionic strengths as high as 12 m show that very high ionic strength brines have an inhibitory effect of forsterite dissolution rates. Multiple linear regression analysis of the data suggests that the inhibition in dissolution rates is due to decreased water activity at high ionic strengths. Regression models also show that mMg up to 4 m and mSO4 up to 3 m have no effect on forsterite dissolution rates. The effect of decreasing dissolution rates with decreasing aH2O is consistent with the idea that water acts as a ligand that participates in the dissolution process. Less available water to participate in the dissolution reaction results in a slower dissolution rate. Multiple linear regression analysis of the data produces the rate equation log r = -6.81 - 0.52pH + 3.26log aH2O. Forsterite in dilute solutions with a water activity of one dissolves twice as fast as those in brines with a water activity of 0.8.

  6. Effects of a brine discharge over soft bottom Polychaeta assemblage

    Energy Technology Data Exchange (ETDEWEB)

    Pilar-Ruso, Yoana del [Dpto. de Ciencias del Mar y Biologia Aplicada, Universidad de Alicante, Campus de San Vicente del Raspeig, Ap. 99, E-03080, Alicante (Spain)], E-mail: yoana.delpilar@ua.es; Ossa-Carretero, Jose Antonio de la; Gimenez-Casalduero, Francisca; Sanchez-Lizaso, Jose Luis [Dpto. de Ciencias del Mar y Biologia Aplicada, Universidad de Alicante, Campus de San Vicente del Raspeig, Ap. 99, E-03080, Alicante (Spain)

    2008-11-15

    Desalination is a growing activity that has introduced a new impact, brine discharge, which may affect benthic communities. Although the role of polychaetes as indicators to assess organic pollution is well known, their tolerance to salinity changes has not been examined to such a great extent. The aim of this study was to examine the effect of brine discharge over soft bottom polychaete assemblage along the Alicante coast (Southeast Spain) over a two year period. Changes in the polychaete assemblage was analysed using univariate and multivariate techniques. We compared a transect in front of the discharge with two controls. At each transect we sampled at three depths (4, 10 and 15 m) during winter and summer. We have observed different sensitivity of polychaete families to brine discharges, Ampharetidae being the most sensitive, followed by Nephtyidae and Spionidae. Syllidae and Capitellidae showed some resistance initially, while Paraonidae proved to be a tolerant family. - The Polychaete assemblage is affected by the brine discharge of the Alicante desalination plant and we detect different sensitivity levels in polychaete families to brine impact.

  7. Searching for brine on Mars using Raman spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Fischer, E.

    2016-07-01

    In the last few years, water ice and perchlorate salts capable of melting this ice and producing liquid solutions have been discovered at the surface and shallow subsurface of Mars. In addition to via melting of ice, perchlorate salts may also form liquid solutions by absorbing water vapor when the relative humidity is above a certain threshold in a process known as deliquescence. Formed either by melting or deliquescence, liquid solutions (brine) are the most likely way of liquid water activity on the Martian surface and in the shallow subsurface and are therefore important to understand the habitability of Mars. Using Raman spectroscopy, we provide reference spectra of various mixing states of liquid water, water ice and calcium perchlorate, all of which can occur during brine formation. We focus on the perchlorate symmetric stretching band and the O-H stretching vibrational band to distinguish brine from crystalline salt and water ice. We show that perchlorate brines can be identified by analyzing the peaks and their widths in the decomposed Raman spectra of the investigated samples. This serves as an important reference for future in-situ Raman spectrometers on Mars, such as those on the ExoMars and Mars 2020 rovers and can aid in the detection of brine formation on Mars. (Author)

  8. Effect of digestion time on anaerobic digestion with high ammonia concentration

    Science.gov (United States)

    Oktavitri, Nur Indradewi; Purnobasuki, Hery; Kuncoro, Eko Prasetyo; Purnamasari, Indah; Semma Hadinnata, P.

    2016-03-01

    Anaerobic digestion was developed to treat high concentration organic compound efficiently in certain Digestion Time (DT). High ammonia concentration could influenced removal organic compound in digestion. This bench scale study investigated the effect of digestion time on anaerobic batch reactor with high ammonia concentration. Total Ammonia Nitrogen (TAN) concentration was adjusted 4000 and 5000 mg/1, Digestion time was ranged from 0-26 d, operation temperature was ranged from 28-29°C, inoculum was collected from slaughter house sludge. The degradation of Chemical Oxygen Demand (COD) correlated with digestion time. The concentration of TAN from synthetic wastewater contain 5000 mg/1 of TAN more fluctuated than those use 4000 mg/1 of TAN. However, the biogas production from wastewater contained 4000 mg/1 of TAN gradually increased until 24 d of DT. The reactor contain 5000 mg/1 of TAN only growth until 12 d and steady state at over 12 d of digestion time.

  9. Melatonin in Arabidopsis thaliana acts as plant growth regulator at low concentrations and preserves seed viability at high concentrations.

    Science.gov (United States)

    Hernández, Ismaél Gatica; Gomez, Federico José Vicente; Cerutti, Soledad; Arana, María Verónica; Silva, María Fernanda

    2015-09-01

    Since the discovery of melatonin in plants, several roles have been described for different species, organs, and developmental stages. Arabidopsis thaliana, being a model plant species, is adequate to contribute to the elucidation of the role of melatonin in plants. In this work, melatonin was monitored daily by UHPLC-MS/MS in leaves, in order to study its diurnal accumulation as well as the effects of natural and artificial light treatments on its concentration. Furthermore, the effects of exogenous application of melatonin to assess its role in seed viability after heat stress and as a regulator of growth and development of vegetative tissues were evaluated. Our results indicate that melatonin contents in Arabidopsis were higher in plants growing under natural radiation when compared to those growing under artificial conditions, and its levels were not diurnally-regulated. Exogenous melatonin applications prolonged seed viability after heat stress conditions. In addition, melatonin applications retarded leaf senescence. Its effects as growth promoter were dose and tissue-dependent; stimulating root growth at low concentrations and decreasing leaf area at high doses.

  10. Prodigious Effects of Concentration Intensification on Nanoparticle Synthesis: A High-Quality, Scalable Approach.

    Science.gov (United States)

    Williamson, Curtis B; Nevers, Douglas R; Hanrath, Tobias; Robinson, Richard D

    2015-12-23

    Realizing the promise of nanoparticle-based technologies demands more efficient, robust synthesis methods (i.e., process intensification) that consistently produce large quantities of high-quality nanoparticles (NPs). We explored NP synthesis via the heat-up method in a regime of previously unexplored high concentrations near the solubility limit of the precursors. We discovered that in this highly concentrated and viscous regime the NP synthesis parameters are less sensitive to experimental variability and thereby provide a robust, scalable, and size-focusing NP synthesis. Specifically, we synthesize high-quality metal sulfide NPs (200 g) relative to the current field of large-scale (0.1-5 g yields) and laboratory-scale (<0.1 g) efforts. Compared to conventional synthesis methods (hot injection with dilute precursor concentration) characterized by rapid growth and low yield, our highly concentrated NP system supplies remarkably controlled growth rates and a 10-fold increase in NP volumetric production capacity (86 g/L). The controlled growth, high yield, and robust nature of highly concentrated solutions can facilitate large-scale nanomanufacturing of NPs by relaxing the synthesis requirements to achieve monodisperse products. Mechanistically, our investigation of the thermal and rheological properties and growth rates reveals that this high concentration regime has reduced mass diffusion (a 5-fold increase in solution viscosity), is stable to thermal perturbations (∼64% increase in heat capacity), and is resistant to Ostwald ripening.

  11. High-concentration-gradient dispersion in porous media : experiments, analysis and approximations

    NARCIS (Netherlands)

    R.J. Schotting; H. Moser; S.M. Hassanizadeh

    1997-01-01

    textabstractVarious experimental and theoretical studies have shown that Fick's law, based on the assumption of a linear relation between solute dispersive mass flux and concentration gradient, is not valid when high concentration gradients are encountered in a porous medium. The value of the macrod

  12. Critical phenomena in ethylbenzene oxidation in acetic acid solution at high cobalt(II) concentrations

    NARCIS (Netherlands)

    Gavrichkov, AA; Zakharov, [No Value

    2005-01-01

    Critical phenomena in ethylbenzene oxidation in an acetic acid solution at high cobalt(ill) concentrations (from 0.01 to 0.2 mol L-1) were studied at 60-90 degrees C by the gasometric (O-2 absorption), spectrophotometric (Co-III accumulation), and chemiluminescence (relative concentration of radical

  13. Whey protein particles modulate mechanical properties of gels at high protein concentrations

    NARCIS (Netherlands)

    Saglam, D.; Venema, P.; Vries, de R.J.; Berg, van den L.; Linden, van der E.

    2014-01-01

    We have studied the influence of dense whey protein particles on the mechanical properties of whey protein isolate (WPI) gels at high protein concentrations (16–22% (w/w)). Incorporation of dense whey protein particles in the gel, while keeping the total protein concentration constant, leads to a co

  14. Rheology of dilute acid hydrolyzed corn stover at high solids concentration

    Science.gov (United States)

    M.R. Ehrhardt; T.O. Monz; T.W. Root; R.K. Connelly; Tim Scott; D.J. Klingenberg

    2010-01-01

    The rheological properties of acid hydrolyzed corn stover at high solids concentration (20–35 wt.%) were investigated using torque rheometry. These materials are yield stress fluids whose rheological properties can be well represented by the Bingham model. Yield stresses increase with increasing solids concentration and decrease with increasing hydrolysis reaction...

  15. Effect of dissolved oxygen concentration on the bioflocculation process in high loaded MBRs

    NARCIS (Netherlands)

    Faust, L.; Temmink, B.G.; Zwijnenburg, A.; Kemperman, A.J.B.; Rijnaarts, H.

    2014-01-01

    High-loaded membrane bioreactors (HL-MBRs), i.e. MBRs which are operated at extremely short sludge and hydraulic retention times, can be applied to flocculate and concentrate sewage organic matter. The concentrated organics can be used for energy recovery, or for the production of more valuable

  16. Chemical composition and distribution of lithium-rich brines in salar de Uyuni and nearby salars in southwestern Bolivia

    Science.gov (United States)

    Ericksen, G.E.; Vine, J.D.; Raul, Ballon A.

    1978-01-01

    Preliminary investigations at Salar de Uyuni and the nearby salars (salt pans) of Coipasa and Empexa in the southern part of the Bolivian Altiplano show the presence of widespread lithium-rich brines. Widely scattered brine samples from Salar de Uyuni, which has an area of about 9000 km2 and is the largest salt pan on earth, show lithium values ranging from 80 to 1500 ppm. High values of 300-700 ppm are most prevalent in an area of about 2500 km2 in the east-central and southeastern part of the salar. A few brine samples in small areas in Coipasa and Empexa Salars have values ranging from 170 to 580 ppm Li. All the brines are essentially saturated with halite and are moderately high in sulfate (5000-15,000 ppm SO4) but low in carbonate (Altiplano during late Pleistocene time, augmented by saline material carried to the salars by streams since final drying of this lake. Thermal springs associated with rhyolitic volcanic rocks of Quaternary age may have been a major source of the lithium. ?? 1978.

  17. A High-Efficiency Refractive Secondary Solar Concentrator for High Temperature Solar Thermal Applications

    Science.gov (United States)

    Piszczor, Michael F., Jr.; Macosko, Robert P.

    2000-01-01

    A refractive secondary solar concentrator is a non-imaging optical device that accepts focused solar energy from a primary concentrator and redirects that light, by means of refraction and total internal reflection (TIR) into a cavity where the solar energy is used for power and/or propulsion applications. This concept offers a variety of advantages compared to typical reflective secondary concentrators (or the use of no secondary at all): higher optical efficiency, minimal secondary cooling requirements, a smaller cavity aperture, a reduction of outgassing from the cavity and flux tailoring of the solar energy within the heat receiver. During the past 2 years, NASA Lewis has been aggressively developing this concept in support of the NASA Marshall Shooting Star Flight Experiment. This paper provides a brief overview of the advantages and technical challenges associated with the development of a refractive secondary concentrator and the fabrication of a working unit in support of the flight demonstration program.

  18. Investigating cold gelation properties of recombined highly concentrated micellar casein concentrate and cream for use in cheese making.

    Science.gov (United States)

    Lu, Y; McMahon, D J; Vollmer, A H

    2016-07-01

    Highly concentrated micellar casein concentrate (HC-MCC), a potential ingredient for cheese making, contains ~20% casein with ~70% of serum proteins removed by microfiltration and diafiltration of skim milk, followed by vacuum evaporation. Our objective was to investigate cold gelation properties of recombined concentrated milk (RCM) by mixing thawed frozen HC-MCC and cream under different casein levels, pH, and protein-to-fat ratios, and with addition of sodium citrate or calcium. The HC-MCC was recombined with cream using low shear at 50°C for 30 min, and rheological measurements were conducted. Cold-gelling temperature [the temperature at which storage modulus (G')=loss modulus (G″)] was linearly correlated with casein levels from 8.6 to 11.5% (R(2)=0.71), pH from 6.6 to 7.0 (R(2)=0.96), and addition of sodium citrate from 0 to 0.36mmol/g of casein (R(2)=0.80). At pH 7.0, gelation occurred at 12, 26, and 38°C with 9, 10, and 11% casein, respectively. At pH 6.6, 6.8, and 7.0, RCM with 12% casein gelled at a mean temperature of 12, 26, and 37°C, respectively. Adding calcium chloride at 0.17mmol/g of casein significantly increased cold-gelling temperature from 18 to ≥50°C, whereas no significant change was observed at levels up to 0.12mmol/g of casein. Different protein to fat ratios ranging from 0.8 to 1.2 did not significantly influence gelling temperature. In transmission electron micrographs of RCM with 12% casein, casein micelles were nonspherical and partially dissociated into small protein strands. Upon addition of calcium chloride at 0.21mmol/g of casein, casein micelles were more spherical and retained colloidal structure with the presence of aggregated casein micelles. These gelation processes of RCM with or without addition of trisodium citrate were both reversible. We propose that cold gelation of RCM occurs when protein strands that have been partially released from the casein micelles entangle, restrict their mobility, and form a fine

  19. Phytochemical and toxicity evaluation ofPhaleria macrocarpa (Scheff.) Boerl by MCF-7 cell line and brine shrimp lethality bioassay

    Institute of Scientific and Technical Information of China (English)

    Abul Kalam Azad; Wan Mohd Azizi Wan Sulaiman; Nushrat Khan Sunzida

    2016-01-01

    Objective:To evaluate the cytotoxicity ofPhaleria macrocarpa fruits extracts. Methods: The cytotoxicity test was carried out byin vitroMCF-7 cell line andin vivo brine shrimp lethality bioassay. Results: The preliminary phytochemical test showed the presence of alkaloids, carbohydrate, glycosides, saponin, terpene, steroids, phenols and flavonoids. TheMTT-assay results showed that the highest percentage of cell viability was 106.23% at concentration of 1.25µL and the lowest percentage was 13.04% at concentration of 10µL. Conclusions:TheMTT-assay and brine shrimp lethality bioassay results showed that the extract was non-toxic and it would be consumable as a herbal remedy.

  20. Simulation of H2O-vapor and Brine-CO2 in porous media with a Lattice Boltzmann Model.

    Science.gov (United States)

    Schaap, M. G.

    2014-12-01

    This DOE-BES funded study is a collaboration between Oregon State University (led by Dr. Dorthe Wildenschild) and the University of Arizona to investigate pore-scale aspects of capillary trapping to enhance the efficiency of geological CO2 sequestration. For the purposes of this project it is important to correctly simulate the physical conditions under which super-critical CO2 will be present after injection into the host rock. This means that the LB model should be able to handle the pressures, densities, temperatures in deep geological media. A logical way of dealing with is is to combine a single-component LB model with and Equation of State (EOS) that describes the physical interrelations among pressure, temperature and density. Previously, we showed that the Peng-Robinson (PR) EOS provides an excellent fit to super-critical conditions for the pure CO2 system. However, it is necessary to consider multi-component systems as the super-critical CO2 will be present with brines of varying salinity. A natural extension to the work under is to also treat the brine with an EOS. The brine will of be in a sub-critical state and it is therefore important to find an EOS that can faithfully match the physical conditions of brine between temperatures of 300 and 400K and pressures between 7 and 30 MPa. This study will present a number of EOS alternatives that attempt to correctly capture the density of the liquid branch of the water system for relevant temperatures and pressures. We will also propose modifications that allow us to deal with different brine concentrations and compare LB modeled interfacial tension and viscosity with published data. As a secondary objective we investigate whether it is possible to match water-vapor systems under ambient surface conditions relevant for vadose zone transport. Support: DOE DE-FG02-11ER16278

  1. Degradation of concrete-based barriers by Mg-containing brines: From laboratory experiments via reactive transport modelling to overall safety analysis in repository scale

    Science.gov (United States)

    Niemeyer, Matthias; Wilhelm, Stefan; Hagemann, Sven; Xie, Mingliang; Wollrath, Jürgen; Preuss, Jürgen

    2010-05-01

    The Morsleben nuclear waste repository (ERAM) for low- and intermediate-level radioactive waste is located in an old rock salt and potash mine in Northern Germany. From 1971 to 1998, approximately 36 800 m3 of waste have been disposed of. Now, waste disposal is finished, and the repository has to be backfilled and sealed. The closure concept is based on extensive backfilling of the salt mine with an inexpensive concrete mixture. The major disposal areas, containing most of the waste, will be isolated from the rest of the mine building by sealing the connecting access tunnels. The good geological situation (an intact cap rock with very small flow rates) provides an excellent basic condition for a safe repository. However, the access of water to the remaining parts of the mine cannot be excluded. The brines that are formed in contact with potash salts will contain Mg in a concentration that depends on various factors and cannot be predicted. For backfill and closure of the repository, no common material chemically stable against brines of all possible compositions is available. Salt concrete has a low permeability but is corroded by brines containing Mg, whilst concrete based on Sorel phases is decomposed if the Mg-content of the brines is too low. In each of these alternatives, corrosion results in a strong increase of permeability and a loss of the mechanical integrity of the material. However, for large hydraulic seals the flow of corroding brines is limited because of the high hydraulic resistance of the barrier. Thus, the barriers will persist for a long time in spite of the chemical incompatibility of building material and brine. For the planning of the backfill and closure measures as well as for the license application procedure it is crucial to demonstrate that the seals of the major disposal areas will keep their function for a sufficient long time. This lifetime depends among others on the corrosion capacity of the brine to the building material, on the

  2. Potassium double tungstate waveguides with high ytterbium concentration for optical amplification

    NARCIS (Netherlands)

    Yong, Yean-Sheng

    2017-01-01

    In this thesis, the research work concerning high ytterbium concentration potassium double tungstate waveguides catered for optical amplification purpose is presented. The scope of the research work includes the investigation of spectroscopic and optical gain properties in epitaxy layers with

  3. Methods to assess high-resolution subsurface gas concentrations and gas fluxes in wetland ecosystems

    DEFF Research Database (Denmark)

    Elberling, Bo; Kühl, Michael; Glud, Ronnie N.

    2013-01-01

    The need for measurements of soil gas concentrations and surface fluxes of greenhouse gases at high temporal and spatial resolution in wetland ecosystem has lead to the introduction of several new analytical techniques and methods. In addition to the automated flux chamber methodology for high......-resolution estimates of greenhouse gas fluxes across the soil-atmosphere interface, these high-resolution methods include microsensors for quantification of spatiotemporal concentration dynamics in O2 and N2O at micrometer scales, fiber-optic optodes for long-term continuous point measurements of O2 concentrations...... and peat soils are highly heterogeneous, containing a mosaic of dynamic macropore systems created by both macrofauna and flora leading to distinct spatial and temporal variations in gas concentration on a scale of millimeters and minutes. Applications of these new methodologies allow measurements...

  4. Concentration influences on recovery in a high gradient magnetic separation axial filter

    Energy Technology Data Exchange (ETDEWEB)

    Murariu, V.; Rezlescu, N.; Rotariu, O.; Badescu, V. [Inst. of Technical Physics, Iasi (Romania)

    1998-05-01

    The buildup differential equations for the case of a single wire in high gradient magnetic filtration (HGMF)-axial configuration taking into account the suspension concentration are solved. A new equation for the deposit contour surface at different moments and for different suspension concentrations are obtained. The existence of a particulate suspension concentration, for which the radial extension velocity of deposit is maximum, is evidenced. The recovery for an ordered ferromagnetic matrix is calculated. The influence of the solid particle concentration from suspension on the filtration efficiency is presented.

  5. Storage quality in different brines of pickled capers (Capparis spp.

    Directory of Open Access Journals (Sweden)

    Özcan, Musa

    1999-08-01

    Full Text Available Middle sized buds of Capparis spinosa L. var. spinosa and Capparis ovata Desf. var. canescens (Coss. Heywood collected from wild plants were pickled for two months. The buds after the fermentation were processed in 10% and 20% brines. Storage stability of the fermented capers was determined by physical, chemical and microbiological analysis at certain interval in 10 and 20% old or fresh brines 180 days. Storaged in 10% and 20% old or fresh brines for 180 days of pickled buds of both species maintained the product quality in all samples. Acidity was higher in old brine during storage. Lactic acid bacteria (LAB growth was observed only in 10% fresh brine, it decreased from initial and 30 days at C. ovata and C. spinosa, respectively. C. spinosa, compared with C. ovata was desirable due to low sediment and more firm texture. During storage of buds in fresh brines, sediment and off-flavour were not observed for both species. Pickled products can be stored in fresh brine long-term containing at least 10% salt concentration.

    Se encurtieron durante dos meses botones florales de tamaño intermedio de Capparis spinosa L. var. spinosa y Capparis ovata Desf. var. canescens (Coss recogidos de plantas silvestres. Las alcaparras después de la fermentación se conservaron en salmueras del 10% y 20%. Las alcaparras fermentadas fueron mantenidas durante 180 días en salmueras usadas o recién preparadas (frescas del 10 y 20%, determinándose a intervalos la estabilidad durante la conservación por análisis físicos, químicos y microbiológicos. La calidad del producto se mantuvo en todas las muestras de alcaparras fermentadas durante los 180 días, tanto en 10% como en 20% y en salmueras usadas o frescas. La acidez durante la conservación fue mayor en salmueras usadas. El crecimiento de bacterias del ácido láctico se observó sólo en salmueras frescas del 10

  6. Toxicity of organophosphates on morphology and locomotor behavior in brine shrimp, Artemia salina.

    Science.gov (United States)

    Venkateswara Rao, J; Kavitha, P; Jakka, N M; Sridhar, V; Usman, P K

    2007-08-01

    The acute toxicity and hatching success of four organophosphorus insecticides--acephate (ACEP), chlorpyrifos (CPP), monocrotophos (MCP), and profenofos (PF)--was studied in a short-term bioassay using brine shrimp, Artemia salina. Fifty percent hatchability inhibition concentration and median lethal concentration (LC(50)) values were calculated after probit transformation of the resulting data. Among the insecticides tested, CPP is found to be the most toxic and also to inhibit hatching success of A. salina cysts in a concentration-dependent manner. In addition, the effect of these pesticides on locomotor behavior (swimming speed) and morphologic differences were studied in LC(50)-exposed nauplii after 24 hours. The in vivo effect of these insecticides on acetylcholinesterase (Enzyme commission number (EC 3.1.1.7) activity was also determined in LC(50)-exposed nauplii after 24 hours. Maximum percent decrease in their swimming speed and significant morphologic alterations were noticed in CPP-exposed brine shrimps. The order of toxicity was CPP > PF > MCP > ACEP in all the parameters studied.

  7. Acute Oral Toxicity and Brine Shrimp Lethality of Elaeis guineensis Jacq., (Oil Palm Leaf Methanol Extract

    Directory of Open Access Journals (Sweden)

    Yeng Chen

    2010-11-01

    Full Text Available Elaeis guineensis (Arecaceae is widely used in West African traditional medicine for treating various ailments. An evaluation on the toxicity of extracts of this plant is crucial to support the therapeutic claims. The acute oral toxicity and brine shrimp lethality of a methanolic extract of this plant was tested. Oral administration of crude extract at the highest dose of 5,000 mg/kg resulted in no mortalities or evidence of adverse effects, implying that E. guineensis is nontoxic. Normal behavioral pattern, clinical signs and histology of vital organs confirm this evidence. The E. guineensis extracts screened for toxicity against brine shrimp had 50% lethal concentration (LC50 values of more than 1.0 mg/mL (9.00 and 3.87 mg/mL, at 6 and 24 h, respectively, confirming that the extract was not toxic. Maximum mortalities occurred at 100 mg/mL concentration while the least mortalities happened to be at 0.195 mg/mL concentration. The results of both tests confirm that E. guineensis is nontoxic and hence safe for commercial utilization.

  8. Acute oral toxicity and brine shrimp lethality of Elaeis guineensis Jacq., (oil palm leaf) methanol extract.

    Science.gov (United States)

    Syahmi, Abdul Rani Muhamad; Vijayarathna, Soundararajan; Sasidharan, Sreenivasan; Latha, Lachimanan Yoga; Kwan, Yuet Ping; Lau, Yee Ling; Shin, Lai Ngit; Chen, Yeng

    2010-11-10

    Elaeis guineensis (Arecaceae) is widely used in West African traditional medicine for treating various ailments. An evaluation on the toxicity of extracts of this plant is crucial to support the therapeutic claims. The acute oral toxicity and brine shrimp lethality of a methanolic extract of this plant was tested. Oral administration of crude extract at the highest dose of 5,000 mg/kg resulted in no mortalities or evidence of adverse effects, implying that E. guineensis is nontoxic. Normal behavioral pattern, clinical signs and histology of vital organs confirm this evidence. The E. guineensis extracts screened for toxicity against brine shrimp had 50% lethal concentration (LC₅₀) values of more than 1.0 mg/mL (9.00 and 3.87 mg/mL, at 6 and 24 h, respectively), confirming that the extract was not toxic. Maximum mortalities occurred at 100 mg/mL concentration while the least mortalities happened to be at 0.195 mg/mL concentration. The results of both tests confirm that E. guineensis is nontoxic and hence safe for commercial utilization.

  9. Subcutaneous absorption kinetics of two highly concentrated preparations of recombinant human growth hormone

    DEFF Research Database (Denmark)

    Laursen, Torben; Jørgensen, Jens Otto Lunde; Susgaard, Søren;

    1993-01-01

    Abstract OBJECTIVE: The relative bioavailability of two highly concentrated (12 IU/ml) formulations of biosynthetic human growth hormone (GH) administered subcutaneously was compared. DESIGN: A randomized, crossover study. Conventional GH therapy was withdrawn 72 hours before each study period. T....... CONCLUSIONS: There is no significant difference between the absorption kinetics and short-term metabolic effects of these two highly concentrated formulations of biosynthetic GH. The two formulations are bioequivalent....

  10. A Comparison of the Corrosion Resistance of Iron-Based Amorphous Metals and Austenitic Alloys in Synthetic Brines at Elevated Temperature

    Energy Technology Data Exchange (ETDEWEB)

    Farmer, J C

    2008-11-25

    Several hard, corrosion-resistant and neutron-absorbing iron-based amorphous alloys have now been developed that can be applied as thermal spray coatings. These new alloys include relatively high concentrations of Cr, Mo, and W for enhanced corrosion resistance, and substantial B to enable both glass formation and neutron absorption. The corrosion resistances of these novel alloys have been compared to that of several austenitic alloys in a broad range of synthetic brines, with and without nitrate inhibitor, at elevated temperature. Linear polarization and electrochemical impedance spectroscopy have been used for in situ measurement of corrosion rates for prolonged periods of time, while scanning electron microscopy (SEM) and energy dispersive analysis of X-rays (EDAX) have been used for ex situ characterization of samples at the end of tests. The application of these new coatings for the protection of spent nuclear fuel storage systems, equipment in nuclear service, steel-reinforced concrete will be discussed.

  11. Dispersive Tidal Plume Modeling of Brine Discharge from Reverse Osmosis (RO) Desalination System, Coral Bay, St. John, USVI using Finite Segment Steady-state Response Matrix (SSRM)

    Science.gov (United States)

    Yoon, J.; Shahvari, A.

    2011-12-01

    This characterization and modeling study of dispersive tidal plume of brine discharge from reverse osmosis (RO) desalination system is a part of the Environmental Assessment (EA) for a new reverse osmosis system in the Coral Bay, St. John, USVI (US Virgin Island). Main foci are on developing the tidal longitudinal (perpendicular to the shoreline) and lateral (parallel to the shoreline) dispersion coefficients and subsequently characterize dispersion and mixing characterization of the negatively buoyant brine discharge plume from the proposed reverse osmosis plant to evaluate the level of salinity variations in the nearshore mixing plume in regard to existing coral reef ecosystem. An in situ dye study was conducted by a marine biologist for this purpose to estimate brine discharge plume dispersion coefficients under oscillatory tidal transport and fate flux for current and proposed plant configuration. Additional tidal and surface runoff hydrologic data, bathymetric data and brine discharge characteristics in the vicinity of the brine discharge location are reflected in this study. With estimated dispersion coefficients, eighteen brine discharge scenarios were evaluated to model anticipated dispersive characteristics under varying operational conditions and ambient tidal current conditions for average measured salinity of 33.27 PSU in loco as well as a standard 35 PSU for typical nearshore water salinity variations. Modeling results indicated that the dispersive tidal plume of design brine discharge from reverse osmosis (RO) desalination system at a discharge of 150,000 gpd would raise salinity no higher than 0.0123 PSU in receiving nearshore estuarine water (Maximum concentration at the segment 3 = 33.2822 PSU at Δt = 12 hrs and 24 hrs in diurnal tidal cycle under when the brine discharge with Base+25% concentration, 81.25 PSU at brine discharge rate of 0.0066 m3/sec, and with a minimum direct overland flow efflux at 0.003 m3/sec - this is a "worst-case" operating

  12. Incomplete ion dissociation underlies the weakened attraction between DNA helices at high spermidine concentrations.

    Science.gov (United States)

    Yang, Jie; Rau, Donald C

    2005-09-01

    We have investigated the salt sensitivity of the hexagonal-to-cholesteric phase transition of spermidine-condensed DNA. This transition precedes the resolubilization of precipitated DNA that occurs at high spermidine concentration. The sensitivity of the critical spermidine concentration at the transition point to the anion species and the NaCl concentration indicates that ion pairing of this trivalent ion underlies this unusual transition. Osmotic pressure measurements of spermidine salt solutions are consistent with this interpretation. Spermidine salts are not fully dissociated at higher concentrations. The competition for DNA binding among the fully charged trivalent ion and the lesser charged complex species at higher concentrations significantly weakens attraction between DNA helices in the condensed state. This is contrary to the suggestion that the binding of spermidine at higher concentrations causes DNA overcharging and consequent electrostatic repulsion.

  13. Transcriptional analysis of adaptation to high glucose concentrations in Zymomonas mobilis.

    Science.gov (United States)

    Zhang, Kun; Shao, Huanhuan; Cao, Qinghua; He, Ming-Xiong; Wu, Bo; Feng, Hong

    2015-02-01

    The ethanologenic bacterium Zymomonas mobilis is usually tolerant to high concentrations of glucose. The addition of sorbitol decreases the lag phase and increases ethanol yield and productivity of the bacteria in high glucose concentrations. The molecular mechanisms of adaptation to high glucose concentrations and the effect of sorbitol are still unclear. In this study, microarray analysis was used to study the global transcriptional adaptation responses of Z. mobilis to high glucose concentrations. A total of 235 genes were differentially expressed when 220 g/L glucose was added with or without 10 mM sorbitol. These genes are involved in diverse aspects of cell metabolism and regulation, including membrane transporters, nitrogen metabolism, and plasmid-encoded genes. However, most differentially expressed genes were downregulated when sorbitol was added. Notably, the transcription of almost all genes involved in the Entner-Doudoroff and ethanol production pathways was not significantly affected. In addition, a prophage and a nitrogen-fixation cluster were significantly induced. These results revealed that Z. mobilis cells responded to high glucose concentrations by regulating the transcriptional levels of genes related to membrane channels and transporters, stress response mechanisms, and metabolic pathways. These data provide insight into the intracellular adaptation responses to high glucose concentrations and reveal strategies to engineer efficient ethanol fermentation in Z. mobilis.

  14. EXPERIMENTAL INVESTIGATIONS ON DIFFUSION CHARACTERISTICS OF HIGH CONCENTRATION JETS IN ENVIRONMENTAL CURRENTS

    Institute of Scientific and Technical Information of China (English)

    张燕; 王道增; 樊靖郁

    2002-01-01

    By means of flow visualization and quantitative measurement, the diffusionpattern and concentration distribution characteristics of high concentration jets verticallydischarged into shallow moving waterbody were experimentally investigated in waterchannel. The interactions between the high concentration jets and environmental flowconditions were analysed, and the formulae of impinging point coordinate and transversespread angle are gained from data analysis. Experimental results indicate that the jets showcomplicated flow patterns and diffusion characteristics in near region, which are differentfrom common submerged jets, and spread downstream in the manner of density currents.

  15. Ice Control with Brine Spread with Nozzles on Highways

    DEFF Research Database (Denmark)

    Bolet, Lars; Fonnesbech, Jens Kristian

    2010-01-01

    . The improvements gained by the county of Funen were mainly due to the use of technologies (brine spreading with nozzles) giving a more precise spread pattern than the traditional gritting of pre-wetted salt. The spread pattern for every spreader, tested in The County of Funen, has been meassured 3 hours after...... spreading on a highway with traffic. A total of 800 spots were measured for residual salt for every spreader. The measurements and the spread pattern for brine spreading with nozzles were so precisely, that we learned: “When there is moisture, water or ice on the road, we need to take into account...

  16. First Insights into the Viral Communities of the Deep-sea Anoxic Brines of the Red Sea

    KAUST Repository

    Antunes, Andre

    2015-10-31

    The deep-sea brines of the Red Sea include some of the most extreme and unique environments on Earth. They combine high salinities with increases in temperature, heavy metals, hydrostatic pressure, and anoxic conditions, creating unique settings for thriving populations of novel extremophiles. Despite a recent increase of studies focusing on these unusual biotopes, their viral communities remain unexplored. The current survey explores four metagenomic datasets obtained from different brine-seawater interface samples, focusing specifically on the diversity of their viral communities. Data analysis confirmed that the particle-attached viral communities present in the brine-seawater interfaces were diverse and generally dominated by Caudovirales, yet appearing distinct from sample to sample. With a level of caution, we report the unexpected finding of Phycodnaviridae, which infects algae and plants, and trace amounts of insect-infecting Iridoviridae. Results from Kebrit Deep revealed stratification in the viral communities present in the interface: the upper-interface was enriched with viruses associated with typical marine bacteria, while the lower-interface was enriched with haloviruses and halophages. These results provide first insights into the unexplored viral communities present in deep-sea brines of the Red Sea, representing one of the first steps for ongoing and future sampling efforts and studies.

  17. Reservoir engineering to accelerate dissolution of stored CO{sub 2} in brines

    Energy Technology Data Exchange (ETDEWEB)

    Keith, D.W.; Hassanzadeh, H.; Pooladi-Darvish, M. [Calgary Univ., AB (Canada). Dept. of Chemical and Petroleum Engineering

    2005-07-01

    Although deep aquifers are an important class of geologic storage system due to their large capacity, their storage efficiency and security pose considerable uncertainties in assessing carbon dioxide (CO{sub 2}) storage. Efficiency stipulates the fraction of total aquifer capacity that can be accessed for storage, while security refers to the possibility that stored CO{sub 2} will escape from the aquifer system by upward migration through natural or artificial weaknesses in the capping formation. The GEM (2003) simulator from Computer Modeling Group was used in this study to model the flow of multi-phase, multi-component fluids. Since the CO{sub 2} injected into a saline reservoir is 10-30 per cent less dense than the resident brines, it will flow horizontally in a horizontal aquifer, spreading under the caprock, and then flow upwards through any high permeability zone or artificial penetration. The free-phase CO{sub 2} eventually dissolves in the brines or is trapped as residual gas. Once dissolved, the resulting CO{sub 2}-rich brines are slightly denser than undersaturated brines, rendering them negatively buoyant, and reducing or eliminating the possibility of leakage. This study considered that the only relevant risk of leakage stems from mobile free-phase CO{sub 2}. As such, the storage performance depends on the likelihood that free-phase CO{sub 2} will leak out of the storage formation or alternatively the timescale over which significant leakage is expected to occur; and, the rate at which free-phase CO{sub 2} is immobilized by dissolution in the reservoir fluids or residual gas trapping. This study focused on increasing the rate of dissolution as a means of increasing the volumetric storage efficiency; steer large-scale movement of the free-phase CO{sub 2} bubble away from a known weakness in the caprock; accelerate dissolution through the development of density driven convection within the brine; and, decrease reservoir pressures near the point of

  18. [Study of high temperature water vapor concentration measurement method based on absorption spectroscopy].

    Science.gov (United States)

    Chen, Jiu-ying; Liu, Jian-guo; He, Jun-feng; He, Ya-bai; Zhang, Guang-le; Xu, Zhen-yu; Gang, Qiang; Wang, Liao; Yao, Lu; Yuan, Song; Ruan, Jun; Dai, Yun-hai; Kan, Rui-feng

    2014-12-01

    Tunable diode laser absorption spectroscopy (TDLAS) has been developed to realize the real-time and dynamic measurement of the combustion temperature, gas component concentration, velocity and other flow parameters, owing to its high sensitivity, fast time response, non-invasive character and robust nature. In order to obtain accurate water vapor concentration at high temperature, several absorption spectra of water vapor near 1.39 μm from 773 to 1273 K under ordinary pressure were recorded in a high temperature experiment setup using a narrow band diode laser. The absorbance of high temperature absorption spectra was calculated by combined multi-line nonlinear least squares fitting method. Two water vapor absorption lines near 7154.35 and 7157.73 cm(-1) were selected for measurement of water vapor at high temperature. A model method for high temperature water vapor concentration was first proposed. Water vapor concentration from the model method at high temperature is in accordance with theoretical reasoning, concentration measurement standard error is less than 0.2%, and the relative error is less than 6%. The feasibility of this measuring method is verified by experiment.

  19. The influence of closed brine pockets and permeable brine channels on the thermo-elastic properties of saline ice.

    Science.gov (United States)

    Marchenko, Aleksey; Lishman, Ben

    2017-02-13

    A model of the thermo-elastic behaviour of saline ice is formulated, and model solutions describing thermo-elastic waves (TEW) propagating into a half-space of the ice are investigated. The model is based on a proposal that saline ice is a matrix, which encompasses both closed brine pockets and permeable channels filled with brine. Experiments on the thermal expansion of saline ice samples, and on TEW in saline ice, have been performed in the cold laboratories of the University Centre in Svalbard and in University College London. The experimental data are compared with theoretical conclusions. The experimental data support our hypothesis that the brine in saline ice is divided between closed pockets and open, permeable channels.This article is part of the themed issue 'Microdynamics of ice'.

  20. The influence of closed brine pockets and permeable brine channels on the thermo-elastic properties of saline ice

    Science.gov (United States)

    Marchenko, Aleksey; Lishman, Ben

    2017-02-01

    A model of the thermo-elastic behaviour of saline ice is formulated, and model solutions describing thermo-elastic waves (TEW) propagating into a half-space of the ice are investigated. The model is based on a proposal that saline ice is a matrix, which encompasses both closed brine pockets and permeable channels filled with brine. Experiments on the thermal expansion of saline ice samples, and on TEW in saline ice, have been performed in the cold laboratories of the University Centre in Svalbard and in University College London. The experimental data are compared with theoretical conclusions. The experimental data support our hypothesis that the brine in saline ice is divided between closed pockets and open, permeable channels. This article is part of the themed issue 'Microdynamics of ice'.

  1. Trace element concentrations and gastrointestinal parasites of Arctic terns breeding in the Canadian High Arctic.

    Science.gov (United States)

    Provencher, J F; Braune, B M; Gilchrist, H G; Forbes, M R; Mallory, M L

    2014-04-01

    Baseline data on trace element concentrations are lacking for many species of Arctic marine birds. We measured essential and non-essential element concentrations in Arctic tern (Sterna paradisaea) liver tissue and brain tissue (mercury only) from Canada's High Arctic, and recorded the presence/absence of gastrointestinal parasites during four different phases of the breeding season. Arctic terns from northern Canada had similar trace element concentrations to other seabird species feeding at the same trophic level in the same region. Concentrations of bismuth, selenium, lead and mercury in Arctic terns were high compared to published threshold values for birds. Selenium and mercury concentrations were also higher in Arctic terns from northern Canada than bird species sampled in other Arctic areas. Selenium, mercury and arsenic concentrations varied across the time periods examined, suggesting potential regional differences in the exposure of biota to these elements. For unknown reasons, selenium concentrations were significantly higher in birds with gastrointestinal parasites as compared to those without parasites, while bismuth concentrations were higher in Arctic terns not infected with gastrointestinal parasites.

  2. Long-Term CO2 Exposure Experiments - Geochemical Effects on Brine-Saturated Reservoir Sandstone

    Science.gov (United States)

    Fischer, Sebastian; Zemke, Kornelia; Liebscher, Axel; Wandrey, Maren

    2010-05-01

    The injection of CO2 into deep saline aquifers is the most promising strategy for the reduction of CO2 emissions to the atmosphere via long-term geological storage. The study is part of the CO2SINK project conducted at Ketzin, situated 40 km west of Berlin. There, food grade CO2 has been pumped into the Upper Triassic Stuttgart Formation since June 2008. The main objective of the experimental program is to investigate the effects of long-term CO2 exposure on the physico-chemical properties of the reservoir rock. To achieve this goal, core samples from observation well Ktzi 202 have been saturated with synthetic brine and exposed to CO2 in high quality steel autoclaves at simulated reservoir P-T-conditions of 5.5 MPa and 40 ° C. The synthetic brine had a composition representative of the formation fluid (Förster et al., 2006) of 172.8 g/l NaCl, 8.0 g/l MgCl2×2H2O, 4.8 g/l CaCl2×2H2O and 0.6 g/l KCl. After 15 months, the first set of CO2-exposed samples was removed from the pressure vessels. Thin sections, XRD, SEM as well as EMP data were used to determine the mineralogical features of the reservoir rocks before and after the experiments. Additionally, NMR relaxation and MP was performed to measure poroperm and pore size distribution values of the twin samples. The analyzed samples are fine- to medium grained, moderately well- to well sorted and weakly consolidated sandstones. Quartz and plagioclase are the major components, while K-feldspar, hematite, white & dark mica, chlorite and illite are present in minor and varying amounts. Cements are composed of analcime, dolomite and anhydrite. Some samples show mm- to cm-scale cross-beddings. The laminae comprise lighter, quartz- and feldspar-dominated layers and dark-brownish layers with notably less quartz and feldspars. The results are consistent with those of Blaschke et al. (2008). The plagioclase composition indicates preferred dissolution of the Ca-component and a trend toward albite-rich phases or even pure

  3. High serum uric acid concentration predicts poor survival in patients with breast cancer.

    Science.gov (United States)

    Yue, Cai-Feng; Feng, Pin-Ning; Yao, Zhen-Rong; Yu, Xue-Gao; Lin, Wen-Bin; Qian, Yuan-Min; Guo, Yun-Miao; Li, Lai-Sheng; Liu, Min

    2017-08-26

    Uric acid is a product of purine metabolism. Recently, uric acid has gained much attraction in cancer. In this study, we aim to investigate the clinicopathological and prognostic significance of serum uric acid concentration in breast cancer patients. A total of 443 female patients with histopathologically diagnosed breast cancer were included. After a mean follow-up time of 56months, survival was analysed using the Kaplan-Meier method. To further evaluate the prognostic significance of uric acid concentrations, univariate and multivariate Cox regression analyses were applied. Of the clinicopathological parameters, uric acid concentration was associated with age, body mass index, ER status and PR status. Univariate analysis identified that patients with increased uric acid concentration had a significantly inferior overall survival (HR 2.13, 95% CI 1.15-3.94, p=0.016). In multivariate analysis, we found that high uric acid concentration is an independent prognostic factor predicting death, but insufficient to predict local relapse or distant metastasis. Kaplan-Meier analysis indicated that high uric acid concentration is related to the poor overall survival (p=0.013). High uric acid concentration predicts poor survival in patients with breast cancer, and might serve as a potential marker for appropriate management of breast cancer patients. Copyright © 2017. Published by Elsevier B.V.

  4. Haloanaerobium salsugo sp. nov., a moderately halophilic, anaerobic bacterium from a subterranean brine

    Energy Technology Data Exchange (ETDEWEB)

    Bhupathiraju, V.K.; Sharma, P.K.; Tanner, R.S.; McInerney, M.J. [Univ. of Oklahoma, Norman, OK (United States). Dept. of Botany and Microbiology; Oren, A. [Hebrew Univ. of Jerusalem (Israel); Woese, C.R. [Univ. of Illinois, Urbana, IL (United States). Dept. of Microbiology

    1994-07-01

    A strictly anaerobic, moderately halophilic, gram-negative bacterium was isolated from a highly saline oil field brine. The bacterium was a non-spore-forming, nonmotile rod, appearing singly, in pairs, or occasionally as long chains, and measured 0.3 to 0.4 by 2.6 to 4 {micro}m. The bacterium had a specific requirement for NaCl and grew at NaCl concentrations of between 6 and 24%, with optimal growth at 9% NaCl. The isolate grew at temperatures of between 22 and 51 C and pH values of between 5.6 and 8.0. The doubling time in a complex medium containing 10% NaCl was 9 h. Growth was inhibited by chloramphenicol, tetracycline, and penicillin but not by cycloheximide or azide. Fermentable substrates were predominantly carbohydrates. The end products of glucose fermentation were acetate, ethanol, CO{sub 2}, and H{sub 2}. The major components of the cellular fatty acids were C{sub 14:0}, C{sub 16:0}, C{sub 16:1}, and C{sub 17:0 cyc} acids. The DNA base composition of the isolate was 34 mol% G+C. Oligonucleotide catalog and sequence analyses of the 16S rRNA showed that strain VS-752{sup T} was most closely related to Haloanaerobium praevalens GSL{sup T} (ATCC 33744), the sole member of the genus Haloanaerobium. The authors propose that strain VS-752 (ATCC 51327) by established as the type strain of a new species, Haloanaerobium salsugo, in the genus Haloanaerobium. 40 refs., 3 figs, 5 tabs.

  5. Haloanaerobium salsugo sp. nov., a moderately halophilic, anaerobic bacterium from a subterranean brine.

    Science.gov (United States)

    Bhupathiraju, V K; Oren, A; Sharma, P K; Tanner, R S; Woese, C R; McInerney, M J

    1994-07-01

    A strictly anaerobic, moderately halophilic, gram-negative bacterium was isolated from a highly saline oil field brine. The bacterium was a non-spore-forming, nonmotile rod, appearing singly, in pairs, or occasionally as long chains, and measured 0.3 to 0.4 by 2.6 to 4 microns. The bacterium had a specific requirement for NaCl and grew at NaCl concentrations of between 6 and 24%, with optimal growth at 9% NaCl. The isolate grew at temperatures of between 22 and 51 degrees C and pH values of between 5.6 and 8.0. The doubling time in a complex medium containing 10% NaCl was 9 h. Growth was inhibited by chloramphenicol, tetracycline, and penicillin but not by cycloheximide or azide. Fermentable substrates were predominantly carbohydrates. The end products of glucose fermentation were acetate, ethanol, CO2, and H2. The major components of the cellular fatty acids were C14:0, C16:0, C16:1, and C17:0 cyc acids. The DNA base composition of the isolate was 34 mol% G+C. Oligonucleotide catalog and sequence analyses of the 16S rRNA showed that strain VS-752T was most closely related to Haloanaerobium praevalens GSLT (ATCC 33744), the sole member of the genus Haloanaerobium. We propose that strain VS-752 (ATCC 51327) be established as the type strain of a new species, Haloanaerobium salsugo, in the genus Haloanaerobium.

  6. Evaluation of polymer efficiency on the inhibition of calcium carbonate scale in synthetic brines; Avaliacao da acao de polimeros sobre a inibicao de incrustacoes de carbonato de calcio em salmouras sinteticas

    Energy Technology Data Exchange (ETDEWEB)

    Freitas, Juliana M.; Rodrigues, Jessica S.; Loureiro, Tatiana S.; Lucas, Elizabete F.; Spinelli, Luciana S. [Universidade Federal do Rio de Janeiro, Instituto de Macromoleculas, Laboratorio de Macromoleculas e Coloides na Industria de Petroleo, RJ (Brazil)], e-mail: julianamatos@ima.ufrj.br

    2011-07-01

    The inorganic scale results in serious problems for oil production. This scale results from the incompatibility between the chemical compositions of formation water and injection, and the changes of thermodynamic system. These deposits consist mainly of calcium carbonate and barium sulfate. In order to prevent the formation of these deposits, the petroleum industry has made use of chemicals that act as scale inhibitors. The aim of this study was to test the ability of two types of polymeric inhibitors prevent the formation of calcium carbonate from brines of different compositions with high concentrations of calcium. The inhibitors were tested at varying concentrations and at fixed conditions of temperature, pH, pressure and time. The estimated effectiveness of each inhibitor was measured by complexometric titration. The inhibitor carboxylic acid-based (poly (maleic acid)) was more efficient at relatively low concentrations, which is important both economically and environmentally. (author)

  7. An incidence of very high phosphate concentrations in the waters around Andaman Islands

    Digital Repository Service at National Institute of Oceanography (India)

    Reddy, C.V.G.; Murty, P.S.N.; Sankaranarayanan, V.N.

    at stations close to coasts; 2) vertical distribution of phosphates in 200 metre column does not appear to correspond to any regular accepted pattern and 3) all the phosphates having the abnormally high phosphate concentration were found to be highly turbid...

  8. Influence of Mechanical Activation on Acid Leaching Dephosphorization of High-phosphorus Iron Ore Concentrates

    Institute of Scientific and Technical Information of China (English)

    De-qing ZHU; Hao WANG; Jian PAN; Cong-cong YANG

    2016-01-01

    High pressure roll grinding (HPRG)and ball milling were compared to investigate the influence of me-chanical activation on the acid leaching dephosphorization of a high-phosphorus iron ore concentrate,which was man-ufactured through magnetizing roasting-magnetic separation of high-phosphorus oolitic iron ores.The results indica-ted that when high-phosphorus iron ore concentrates containing 54·92 mass% iron and 0·76 mass% phosphorus were directly processed through acid leaching,iron ore concentrates containing 55·74 mass% iron and 0·33 mass%phosphorus with an iron recovery of 84·64% and dephosphorization of 63·79% were obtained.When high-phosphor-us iron ore concentrates activated by ball milling were processed by acid leaching,iron ore concentrates containing 56·03 mass% iron and 0·21 mass% phosphorus with an iron recovery of 85·65% and dephosphorization of 77·49%were obtained.Meanwhile,when high-phosphorus iron ore concentrates activated by HPRG were processed by acid leaching,iron ore concentrates containing 58·02 mass% iron and 0·10 mass% phosphorus were obtained,with the iron recovery reaching 88·42% and the dephosphorization rate reaching 88·99%.Mechanistic studies demonstrated that ball milling can reduce the particle size,demonstrating a prominent reunion phenomenon.In contrast,HPRG pretreatment contributes to the formation of more cracks within the particles and selective dissociation of iron and P bearing minerals,which can provide the favorable kinetic conditions to accelerate the solid-liquid reaction rate.As such,the crystal structure is destroyed and the surface energy of mineral particles is strengthened by mechanical ac-tivation,further strengthening the dephosphorization.

  9. Prodigious Effects of Concentration Intensification on Nanoparticle Synthesis: A High-Quality, Scalable Approach

    KAUST Repository

    Williamson, Curtis B.

    2015-12-23

    © 2015 American Chemical Society. Realizing the promise of nanoparticle-based technologies demands more efficient, robust synthesis methods (i.e., process intensification) that consistently produce large quantities of high-quality nanoparticles (NPs). We explored NP synthesis via the heat-up method in a regime of previously unexplored high concentrations near the solubility limit of the precursors. We discovered that in this highly concentrated and viscous regime the NP synthesis parameters are less sensitive to experimental variability and thereby provide a robust, scalable, and size-focusing NP synthesis. Specifically, we synthesize high-quality metal sulfide NPs (<7% relative standard deviation for Cu2-xS and CdS), and demonstrate a 10-1000-fold increase in Cu2-xS NP production (>200 g) relative to the current field of large-scale (0.1-5 g yields) and laboratory-scale (<0.1 g) efforts. Compared to conventional synthesis methods (hot injection with dilute precursor concentration) characterized by rapid growth and low yield, our highly concentrated NP system supplies remarkably controlled growth rates and a 10-fold increase in NP volumetric production capacity (86 g/L). The controlled growth, high yield, and robust nature of highly concentrated solutions can facilitate large-scale nanomanufacturing of NPs by relaxing the synthesis requirements to achieve monodisperse products. Mechanistically, our investigation of the thermal and rheological properties and growth rates reveals that this high concentration regime has reduced mass diffusion (a 5-fold increase in solution viscosity), is stable to thermal perturbations (64% increase in heat capacity), and is resistant to Ostwald ripening.

  10. A novel mercuric reductase from the unique deep brine environment of atlantis II in the red sea

    KAUST Repository

    Sayed, Ahmed Anazadeh

    2013-11-26

    Aunique combination of physicochemical conditions prevails in the lower convective layer (LCL) of the brine pool at Atlantis II (ATII) Deep in the Red Sea. With a maximum depth of over 2000 m, the pool is characterized by acidic pH (5.3), high temperature (68 °C), salinity (26%), low light levels, anoxia, and high concentrations of heavy metals. We have established a metagenomic dataset derived from the microbial community in the LCL, and here we describe a gene for a novel mercuric reductase, a key component of the bacterial detoxification system for mercuric and organomercurial species. The metagenome-derived gene and an ortholog from an uncultured soil bacterium were synthesized and expressed in Escherichia coli. The properties of their products show that, in contrast to the soil enzyme, the ATII-LCL mercuric reductase is functional in high salt, stable at high temperatures, resistant to high concentrations of Hg2+, and efficiently detoxifies Hg2+ in vivo. Interestingly, despite the marked functional differences between the orthologs, their amino acid sequences differ by less than 10%. Site-directed mutagenesis and kinetic analysis of the mutant enzymes, in conjunction with three-dimensional modeling, have identified distinct structural features that contribute to extreme halophilicity, thermostability, and high detoxification capacity, suggesting that these were acquired independently during the evolution of this enzyme. Thus, our work provides fundamental structural insights into a novel protein that has undergone multiple biochemical and biophysical adaptations to promote the survival of microorganisms that reside in the extremely demanding environment of the ATII-LCL. © 2014 by The American Society for Biochemistry and Molecular Biology, Inc.

  11. Design and Evaluation of the Highly Concentrated Human IgG Formulation Using Cyclodextrin Polypseudorotaxane Hydrogels.

    Science.gov (United States)

    Higashi, Taishi; Tajima, Anna; Ohshita, Naoko; Hirotsu, Tatsunori; Abu Hashim, Irhan Ibrahim; Motoyama, Keiichi; Koyama, Sawako; Iibuchi, Ruriko; Mieda, Shiuhei; Handa, Kenji; Kimoto, Tomoaki; Arima, Hidetoshi

    2015-12-01

    To achieve the potent therapeutic effects of human immunoglobulin G (IgG), highly concentrated formulations are required. However, the stabilization for highly concentrated human IgG is laborious work. In the present study, to investigate the potentials of polypseudorotaxane (PPRX) hydrogels consisting of polyethylene glycol (PEG) and α- or γ-cyclodextrin (α- or γ-CyD) as pharmaceutical materials for highly concentrated human IgG, we designed the PPRX hydrogels including human IgG and evaluated their pharmaceutical properties. The α- and γ-CyDs formed PPRX hydrogels with PEG (M.W. 20,000) even in the presence of highly concentrated human IgG (>100 mg/mL). According to the results of (1)H-NMR, powder X-ray diffraction, and Raman microscopy, the formation of human IgG/CyD PPRX hydrogels was based on physical cross-linking arising from their columnar structures. The release profiles of human IgG from the hydrogels were in accordance with the non-Fickian diffusion model. Importantly, the stabilities of human IgG included into the hydrogels against thermal and shaking stresses were markedly improved. These findings suggest that PEG/CyD PPRX hydrogels are useful to prepare the formulation for highly concentrated human IgG.

  12. Possible salt mine and brined cavity sites for radioactive waste disposal in the northeastern southern peninsula of Michigan. [Seven possible sites are considered on the basis of listed criteria

    Energy Technology Data Exchange (ETDEWEB)

    Landes, K.K.; Bourne, H.L.

    1976-05-31

    A reconnaissance report on the possibilities for disposal of radioactive waste covers Michigan only, and is more detailed than an earlier one involving the northeastern states. Revised ''ground rules'' for pinpointing both mine and dissolved salt cavern sites for waste disposal include environmental, geologic, and economic factors. The Michigan basin is a structural bowl of Paleozoic sediments resting on downwarped Precambrian rocks. The center of the bowl is in Clare and Gladwin Counties, a short distance north of the middle of the Southern Peninsula. The strata dip toward this central area, and some stratigraphic sequences, including especially the salt-containing Silurian section, increase considerably in thickness in that direction. Lesser amounts of salt are also present in the north central part of the Lower Peninsula. Michigan has been an oil and gas producing state since 1925 and widespread exploration has had two effects on the selection of waste disposal sites: (1) large areas are leased for oil and gas; and (2) the borehole concentrations, whether producing wells, dry holes, or industrial brine wells that penetrated the salt section, should be avoided. Two types of nuclear waste, low level and high level, can be stored in man-made openings in salt beds. The storage facilities are created by (1) the development of salt mines where the depths are less than 3000 ft, and (2) cavities produced by pumping water into a salt bed, and bringing brine back out. The high level waste disposal must be confined to mines of limited depth, but the low level wastes can be accommodated in brine cavities at any depth. Seven potential prospects have been investigated and are described in detail.

  13. High Concentrating GaAs Cell Operation Using Optical Waveguide Solar Energy System

    Science.gov (United States)

    Nakamura, T.; Case, J. A.; Timmons, M. L.

    2004-01-01

    This paper discusses the result of the concentrating photovoltaic (CPV) cell experiments conducted with the Optical Waveguide (OW) Solar Energy System. The high concentration GaAs cells developed by Research Triangle Institute (RTI) were combined with the OW system in a "fiber-on-cell" configuration. The sell performance was tested up to the solar concentration of 327. Detailed V-I characteristics, power density and efficiency data were collected. It was shown that the CPV cells combined with the OW solar energy system will be an effective electric power generation device.

  14. Photorespiration and carbon concentrating mechanisms: two adaptations to high O2, low CO2 conditions.

    Science.gov (United States)

    Moroney, James V; Jungnick, Nadine; Dimario, Robert J; Longstreth, David J

    2013-11-01

    This review presents an overview of the two ways that cyanobacteria, algae, and plants have adapted to high O2 and low CO2 concentrations in the environment. First, the process of photorespiration enables photosynthetic organisms to recycle phosphoglycolate formed by the oxygenase reaction catalyzed by ribulose-1,5-bisphosphate carboxylase/oxygenase (Rubisco). Second, there are a number of carbon concentrating mechanisms that increase the CO2 concentration around Rubisco which increases the carboxylase reaction enhancing CO2 fixation. This review also presents possibilities for the beneficial modification of these processes with the goal of improving future crop yields.

  15. Influences of the Basin Brines on Extractable Bitumen of Kupferschiefer from southwestern Poland

    Institute of Scientific and Technical Information of China (English)

    孙玉壮

    2000-01-01

    A study of the influences of the basin brines on hydrocarbon generation of the Kupferschiefer in southwestern Poland has been carried out.The samples from the Konrad and Polkowics mines were analyzed by orgainc geochemical,microscopic and FTIR methods.The results indicate that organic matter of Kupferschiefer tends to decrease with the ascending,oxidizing brines,In the Konrad profile,the Kupferschiefer was strongly oxidized.The extract yields were depleted up to 50mg Ext/g Corg.Gas chromatography(GC) and gas chromatography-mass spctrometry(GC/MS) data indicate that the depletion occureed predominantly in saturated hydrocarbon compounds.The identified n-alkanes in smpale KD1 were depleted at least to 5000μg/g Corg.The aromatic compounds show a fidderent trend of variation.The concentrations of phenanthrene+ alkylphenanthrenes(Ph-PAH) and naphthalene+alkylnaphthalenes(Na-PAH) show a decrease,whereas sulfur polyaromatic hydrocarbons(S-PAH)and oxygen polyaromatic hydrocarbons(O-PAH) show an incrase under the influences of oxidizing brines,In the Polkowice profile,organic matter under the influences of oxidizing fluids shows a simlar trend of varation as in the Konrad mine.Analyses of polar compounds shed light on the oxidation processes at the molecule level.The dominant products of oxidation are aliphatic acid.alcohol and ester.FTIR results indicate that the oxidation of organic matter led to a decrease in aliphatic CH3 and an increase in C-O,C=O bands.

  16. Brine transport in porous media self-similar solutions

    NARCIS (Netherlands)

    C.J. van Duijn (Hans); L.A. Peletier (Bert); R.J. Schotting

    1996-01-01

    textabstractIn this paper we analyze a model for brine transport in porous media, which includes a mass balance for the fluid, a mass balance for salt, Darcy's law and an equation of state, which relates the fluid density to the salt mass fraction. This model incorporates the effect of local volume

  17. Solar desalination, brine and fine chemicals - a preliminary report

    Digital Repository Service at National Institute of Oceanography (India)

    Shirodkar, P.V.; Nagarajan, R.

    Solar stills put into operation by taking known quantities of sea water of different salinities varying from 27.75-36.27 x 10 super(3) during April-May 1990, indicated fresh water yield of 55-68% (av. 64). The volumes of brine as well as those...

  18. Solar desalination, brine and fine chemicals - a preliminary report

    Digital Repository Service at National Institute of Oceanography (India)

    Shirodkar, P.V.; Nagarajan, R.

    Solar stills put into operation by taking known quantities of sea water of different salinities varying from 27. 75 - 36.27 x 103 during April-May 1990, indicated fresh water yield of 55-68% (av. 64) The volumes of brine as well as those of bitterns...

  19. Brine Shrimp and Their Habitat, An Environmental Investigation.

    Science.gov (United States)

    National Wildlife Federation, Washington, DC.

    This environmental unit is one of a series designed for integration within the existing curriculum. The unit is self-contained and students are encouraged to work at their own speed. The philosophy of the unit is based on an experience-oriented process that encourages independent student work. This unit explores the life cycle of brine shrimp and…

  20. determination of toxicity levels of some savannah plants using brine ...

    African Journals Online (AJOL)

    DR. AMINU

    were determined at 95% confidence intervals by analyzing the data on a computer loaded with .... LC50 (µg/ml ). Curcubitacea. Momordica charantia Linn. Leaves. Anti-cancer. F1. 12 (389 – 0.08) ... pesticides using the brine shrimp lethality.