WorldWideScience

Sample records for high boiling organic

  1. Full evaporation headspace gas chromatography for sensitive determination of high boiling point volatile organic compounds in low boiling matrices.

    Science.gov (United States)

    Mana Kialengila, Didi; Wolfs, Kris; Bugalama, John; Van Schepdael, Ann; Adams, Erwin

    2013-11-08

    Determination of volatile organic components (VOC's) is often done by static headspace gas chromatography as this technique is very robust and combines easy sample preparation with good selectivity and low detection limits. This technique is used nowadays in different applications which have in common that they have a dirty matrix which would be problematic in direct injection approaches. Headspace by nature favors the most volatile compounds, avoiding the less volatile to reach the injector and column. As a consequence, determination of a high boiling solvent in a lower boiling matrix becomes challenging. Determination of VOCs like: xylenes, cumene, N,N-dimethylformamide (DMF), dimethyl sulfoxide (DMSO), N,N-dimethylacetamide (DMA), N-methyl-2-pyrrolidone (NMP), 1,3-dimethyl-2-imidazolidinone (DMI), benzyl alcohol (BA) and anisole in water or water soluble products are an interesting example of the arising problems. In this work, a headspace variant called full evaporation technique is worked out and validated for the mentioned solvents. Detection limits below 0.1 μg/vial are reached with RSD values below 10%. Mean recovery values ranged from 92.5 to 110%. The optimized method was applied to determine residual DMSO in a water based cell culture and DMSO and DMA in tetracycline hydrochloride (a water soluble sample). Copyright © 2013 Elsevier B.V. All rights reserved.

  2. Numerical simulation of flow boiling for organic fluid with high saturation temperature in vertical porous coated tube

    Energy Technology Data Exchange (ETDEWEB)

    Yang Dong, E-mail: dyang@mail.xjtu.edu.cn [State Key Laboratory of Multiphase Flow in Power Engineering, Xi' an Jiaotong University, Xi' an, Shaanxi Province 710049 (China); Pan Jie; Wu Yanhua; Chen Tingkuan [State Key Laboratory of Multiphase Flow in Power Engineering, Xi' an Jiaotong University, Xi' an, Shaanxi Province 710049 (China); Zhou, Chenn Q. [Department of Mechanical Engineering, Purdue University Calumet, Hammond, IN 46323 (United States)

    2011-08-15

    Highlights: > A model is developed for the prediction of flow boiling in vertical porous tubes. > The model assumes that the nucleate boiling plays an important role. > The present model can predict most of the experimental values within {+-}20%. > The results indicate the nucleate boiling contribution decreases from 50% to 15%. - Abstract: A semi-analytical model is developed for the prediction of flow boiling heat transfer inside vertical porous coated tubes. The model assumes that the forced convection and nucleate boiling coexist together in the annular flow regime. Conservations of mass, momentum, and energy are used to solve for the liquid film thickness and temperature. The heat flux due to nucleate boiling consists of those inside and outside micro-tunnels. To close the equations, a detailed analysis of various forces acting on the bubble is presented to predict its mean departure diameter. The active nucleation site density of porous layer is determined from the pool boiling correlation by introducing suppression factor. The flow boiling heat transfer coefficients of organic fluid (cumene) with high saturation temperature in a vertical flame-spraying porous coated tube are studied numerically. It is shown that the present model can predict most of the experimental values within {+-}20%. The numerical results also indicate that the nucleate boiling contribution to the overall heat transfer coefficient decreases from 50% to 15% with vapor quality increasing from 0.1 to 0.5.

  3. Experience in operation of the experimental atomic power plant ''ARBUS'' with the high-boiling organic coolant-moderator ditolylmethane

    Energy Technology Data Exchange (ETDEWEB)

    Tzikanov, V.A.; Aleksenko, Yu.N.; Tetyukov, V.D.; Kuprienko, V.A.; Kobzar, I.G.; Khramchenkov, V.A.; Mexcheryakov, M.P.; Zinoviev, V.I.

    1978-04-01

    Radiolytic damage to the ditolylmethane organic coolant-moderator of the ARBUS reactor was removed by vacuum distillation. The majority of the degraded ditolylmethane formed gaseous and high-boiling materials, which were easily removed by the vacuum distillation. Unsaturated hydrocarbons and low-boiling residues were a minor contribution to the impurities produced by radiolysis in the primary coolant loop. Radioactivity in the primary coolant loop was found to be caused primarily from corrosion products of the system, /sup 16/N from dissolved oxygen, and impurities in the coolant-moderator. These also were significantly reduced in the vacuum distillation process.

  4. High flux film and transition boiling

    Science.gov (United States)

    Witte, L. C.

    1993-02-01

    An investigation was conducted on the potential for altering the boiling curve through effects of high velocity and high subcooling. Experiments using water and Freon-113 flowing over cylindrical electrical heaters in crossflow were made to see how velocity and subcooling affect the boiling curve, especially the film and transition boiling regions. We sought subcooling levels down to near the freezing points of these two liquids to prove the concept that the critical heat flux and the minimum heat flux could be brought together, thereby averting the transition region altogether. Another emphasis was to gain insight into how the various boiling regions could be represented mathematically on various parts of the heating surface. Motivation for the research grew out of a realization that the effects of very high subcooling and velocity might be to avert the transition boiling altogether so that the unstable part of the boiling curve would not limit the application of high flux devices to temperatures less than the burnout temperatures. Summaries of results from the study are described. It shows that the potential for averting the transition region is good and points the way to further research that is needed to demonstrate the potential.

  5. Prediction of boiling points of organic compounds by QSPR tools.

    Science.gov (United States)

    Dai, Yi-min; Zhu, Zhi-ping; Cao, Zhong; Zhang, Yue-fei; Zeng, Ju-lan; Li, Xun

    2013-07-01

    The novel electro-negativity topological descriptors of YC, WC were derived from molecular structure by equilibrium electro-negativity of atom and relative bond length of molecule. The quantitative structure-property relationships (QSPR) between descriptors of YC, WC as well as path number parameter P3 and the normal boiling points of 80 alkanes, 65 unsaturated hydrocarbons and 70 alcohols were obtained separately. The high-quality prediction models were evidenced by coefficient of determination (R(2)), the standard error (S), average absolute errors (AAE) and predictive parameters (Qext(2),RCV(2),Rm(2)). According to the regression equations, the influences of the length of carbon backbone, the size, the degree of branching of a molecule and the role of functional groups on the normal boiling point were analyzed. Comparison results with reference models demonstrated that novel topological descriptors based on the equilibrium electro-negativity of atom and the relative bond length were useful molecular descriptors for predicting the normal boiling points of organic compounds. Copyright © 2013 Elsevier Inc. All rights reserved.

  6. High flux film and transition boiling

    Energy Technology Data Exchange (ETDEWEB)

    Witte, L.C.

    1990-01-01

    This report is a bench-scale experiment on transition boiling. The author gives a detailed description on experimental apparatus and conditions. The visual observed boiling phenomena; nucleate boiling and film boiling, and the effect of heat transfer are also elucidated. 10 refs., 11 figs., 1 tab.

  7. An Analytical Approach for Relating Boiling Points of Monofunctional Organic Compounds to Intermolecular Forces

    Science.gov (United States)

    Struyf, Jef

    2011-01-01

    The boiling point of a monofunctional organic compound is expressed as the sum of two parts: a contribution to the boiling point due to the R group and a contribution due to the functional group. The boiling point in absolute temperature of the corresponding RH hydrocarbon is chosen for the contribution to the boiling point of the R group and is a…

  8. An Analytical Approach for Relating Boiling Points of Monofunctional Organic Compounds to Intermolecular Forces

    Science.gov (United States)

    Struyf, Jef

    2011-01-01

    The boiling point of a monofunctional organic compound is expressed as the sum of two parts: a contribution to the boiling point due to the R group and a contribution due to the functional group. The boiling point in absolute temperature of the corresponding RH hydrocarbon is chosen for the contribution to the boiling point of the R group and is a…

  9. High level disinfection of a home care device; to boil or not to boil?

    Science.gov (United States)

    Winthrop, K L; Homestead, N

    2012-03-01

    We developed a percutaneous electrical transducer for home therapy of chronic pain, a device that requires high level disinfection between uses. The utility of boiling water to provide high level disinfection was evaluated by inoculating transducer pads with potential skin pathogens (Staphylococcus aureus, Mycobacterium terrae, Pseudomonas aeruginosa, Candida albicans) and subjecting them to full immersion in water boiling at 4200 feet elevation (95 °C). Log10 reductions in colony-forming units (cfu) at 10 min were 7.1, >6.3 and >5.5 for S. aureus, P. aeruginosa and C. albicans, respectively, but only 4.6 for M. terrae. At 15 min the reductions had increased to 7.5, >6.8, >6.6 and >7.5 cfu, respectively.

  10. Size-exclusion chromatography for the determination of the boiling point distribution of high-boiling petroleum fractions.

    Science.gov (United States)

    Boczkaj, Grzegorz; Przyjazny, Andrzej; Kamiński, Marian

    2015-03-01

    The paper describes a new procedure for the determination of boiling point distribution of high-boiling petroleum fractions using size-exclusion chromatography with refractive index detection. Thus far, the determination of boiling range distribution by chromatography has been accomplished using simulated distillation with gas chromatography with flame ionization detection. This study revealed that in spite of substantial differences in the separation mechanism and the detection mode, the size-exclusion chromatography technique yields similar results for the determination of boiling point distribution compared with simulated distillation and novel empty column gas chromatography. The developed procedure using size-exclusion chromatography has a substantial applicability, especially for the determination of exact final boiling point values for high-boiling mixtures, for which a standard high-temperature simulated distillation would have to be used. In this case, the precision of final boiling point determination is low due to the high final temperatures of the gas chromatograph oven and an insufficient thermal stability of both the gas chromatography stationary phase and the sample. Additionally, the use of high-performance liquid chromatography detectors more sensitive than refractive index detection allows a lower detection limit for high-molar-mass aromatic compounds, and thus increases the sensitivity of final boiling point determination. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. High heat flux transport by microbubble emission boiling

    Science.gov (United States)

    Suzuki, Koichi

    2007-10-01

    In highly subcooled flow boiling, coalescing bubbles on the heating surface collapse to many microbubbles in the beginning of transition boiling and the heat flux increases higher than the ordinary critical heat flux. This phenomenon is called Microbubble Emission Boiling, MEB. It is generated in subcooled flow boiling and the maximum heat flux reaches about 1 kW/cm2(10 MW/m2) at liquid subcooling of 40 K and liquid velocity of 0.5 m/s for a small heating surface of 10 mm×10 mm which is placed at the bottom surface of horizontal rectangular channel. The high pressure in the channel is observed at collapse of the coalescing bubbles and it is closely related the size of coalescing bubbles. Periodic pressure waves are observed in MEB and the heat flux increases linearly in proportion to the pressure frequency. The frequency is considered the frequency of liquid-solid exchange on the heating surface. For the large sized heating surface of 50 mm length×20 mm width, the maximum heat flux obtained is 500 W/cm2 (5 MW/m2) at liquid subcooling of 40 K and liquid velocity of 0.5 m/s. This is considerably higher heat flux than the conventional cooling limit in power electronics. It is difficult to remove the high heat flux by MEB for a longer heating surface than 50 mm by single channel type. A model of advanced cooling device is introduced for power electronics by subcooled flow boiling with impinging jets. Themaxumum cooling heat flux is 500 W/cm2 (5 MW/m2). Microbubble emission boiling is useful for a high heat flux transport technology in future power electronics used in a fuel-cell power plant and a space facility.

  12. Science 101: Why Does It Take Longer to Boil Potatoes at High Altitudes?

    Science.gov (United States)

    Robertson, Bill

    2017-01-01

    Why Does It Take Longer to Boil Potatoes at High Altitudes? This column provides background science information for elementary teachers. This month's issue looks at why water boils at different temperatures at different altitudes.

  13. High Heat Flux Burnout in Subcooled Flow Boiling

    Institute of Scientific and Technical Information of China (English)

    G.P.Celata; M.Cumo; 等

    1995-01-01

    The paper reports the results of an experimental research carried out at the Heat transfer divison of the Energy Department,C.R.Casaccia,on the thermal hydraulic characterization of subcooled flow boiling CHF under typical conditions of thermonuclear fusion reactors.I.e.high liquid velocity and subcooling.The experiment was carried out exploring the following parameters:channel diameter(from 2.5to 8.0 mm),heated length(10 and 15cm) ,liquid velocity (from 2 to 40m/s),exit pressure(from atmospheric to 5.0 MPa),inlet temperature(from 30 to 80℃),channel orientation (vertical and horizontal),A maximum CHF value of 60.6MW/m2 has been obtained under the following conditions:Tin-30°,p=2.5MPa,u=40m/s,D=2.5mm(smooth channel) Turbulence promoters(helically coiled wires)have been employed to further enhance the CHF attainable with subcooled flow boiling.Helically coiled wires allow an increase of 50% of the maximum CHF obtained with smooth channels.

  14. High conversion pressurized water reactor with boiling channels

    Energy Technology Data Exchange (ETDEWEB)

    Margulis, M., E-mail: maratm@post.bgu.ac.il [The Unit of Nuclear Engineering, Ben Gurion University of the Negev, POB 653, Beer Sheva 84105 (Israel); Shwageraus, E., E-mail: es607@cam.ac.uk [Department of Engineering, University of Cambridge, CB2 1PZ Cambridge (United Kingdom)

    2015-10-15

    Highlights: • Conceptual design of partially boiling PWR core was proposed and studied. • Self-sustainable Th–{sup 233}U fuel cycle was utilized in this study. • Seed-blanket fuel assembly lattice optimization was performed. • A coupled Monte Carlo, fuel depletion and thermal-hydraulics studies were carried out. • Thermal–hydraulic analysis assured that the design matches imposed safety constraints. - Abstract: Parametric studies have been performed on a seed-blanket Th–{sup 233}U fuel configuration in a pressurized water reactor (PWR) with boiling channels to achieve high conversion ratio. Previous studies on seed-blanket concepts suggested substantial reduction in the core power density is needed in order to operate under nominal PWR system conditions. Boiling flow regime in the seed region allows more heat to be removed for a given coolant mass flow rate, which in turn, may potentially allow increasing the power density of the core. In addition, reduced moderation improves the breeding performance. A two-dimensional design optimization study was carried out with BOXER and SERPENT codes in order to determine the most attractive fuel assembly configuration that would ensure breeding. Effects of various parameters, such as void fraction, blanket fuel form, number of seed pins and their dimensions, on the conversion ratio were examined. The obtained results, for which the power density was set to be 104 W/cm{sup 3}, created a map of potentially feasible designs. It was found that several options have the potential to achieve end of life fissile inventory ratio above unity, which implies potential feasibility of a self-sustainable Thorium fuel cycle in PWRs without significant reduction in the core power density. Finally, a preliminary three-dimensional coupled neutronic and thermal–hydraulic analysis for a single seed-blanket fuel assembly was performed. The results indicate that axial void distribution changes drastically with burnup. Therefore

  15. Numerical prediction of nucleate pool boiling heat transfer coefficient under high heat fluxes

    OpenAIRE

    Pezo Milada L.; Stevanović Vladimir D.

    2016-01-01

    This paper presents CFD (Computational Fluid Dynamics) approach to prediction of the heat transfer coefficient for nucleate pool boiling under high heat fluxes. Three-dimensional numerical simulations of the atmospheric saturated pool boiling are performed. Mathematical modelling of pool boiling requires a treatment of vapor-liquid two-phase mixture on the macro level, as well as on the micro level, such as bubble growth and departure from the heating surfa...

  16. Aging study of boiling water reactor high pressure injection systems

    Energy Technology Data Exchange (ETDEWEB)

    Conley, D.A.; Edson, J.L.; Fineman, C.F. [Lockheed Idaho Technologies Co., Idaho Falls, ID (United States)

    1995-03-01

    The purpose of high pressure injection systems is to maintain an adequate coolant level in reactor pressure vessels, so that the fuel cladding temperature does not exceed 1,200{degrees}C (2,200{degrees}F), and to permit plant shutdown during a variety of design basis loss-of-coolant accidents. This report presents the results of a study on aging performed for high pressure injection systems of boiling water reactor plants in the United States. The purpose of the study was to identify and evaluate the effects of aging and the effectiveness of testing and maintenance in detecting and mitigating aging degradation. Guidelines from the United States Nuclear Regulatory Commission`s Nuclear Plant Aging Research Program were used in performing the aging study. Review and analysis of the failures reported in databases such as Nuclear Power Experience, Licensee Event Reports, and the Nuclear Plant Reliability Data System, along with plant-specific maintenance records databases, are included in this report to provide the information required to identify aging stressors, failure modes, and failure causes. Several probabilistic risk assessments were reviewed to identify risk-significant components in high pressure injection systems. Testing, maintenance, specific safety issues, and codes and standards are also discussed.

  17. A high-fidelity approach towards simulation of pool boiling

    Energy Technology Data Exchange (ETDEWEB)

    Yazdani, Miad; Radcliff, Thomas; Soteriou, Marios; Alahyari, Abbas A. [United Technologies Research Center, East Hartford, Connecticut 06108 (United States)

    2016-01-15

    A novel numerical approach is developed to simulate the multiscale problem of pool-boiling phase change. The particular focus is to develop a simulation technique that is capable of predicting the heat transfer and hydrodynamic characteristics of nucleate boiling and the transition to critical heat flux on surfaces of arbitrary shape and roughness distribution addressing a critical need to design enhanced boiling heat transfer surfaces. The macro-scale of the phase change and bubble dynamics is addressed through employing off-the-shelf Computational Fluid Dynamics (CFD) methods for interface tracking and interphase mass and energy transfer. The micro-scale of the microlayer, which forms at early stage of bubble nucleation near the wall, is resolved through asymptotic approximation of the thin-film theory which provides a closed-form solution for the distribution of the micro-layer and its influence on the evaporation process. In addition, the sub-grid surface roughness is represented stochastically through probabilistic density functions and its role in bubble nucleation and growth is then represented based on the thermodynamics of nucleation process. This combination of deterministic CFD, local approximation, and stochastic representation allows the simulation of pool boiling on any surface with known roughness and enhancement characteristics. The numerical model is validated for dynamics and hydrothermal characteristics of a single nucleated bubble on a flat surface against available literature data. In addition, the prediction of pool-boiling heat transfer coefficient is verified against experimental measurements as well as reputable correlations for various roughness distributions and different surface orientations. Finally, the model is employed to demonstrate pool-boiling phenomenon on enhanced structures with reentrance cavities and to explore the effect of enhancement feature design on thermal and hydrodynamic characteristics of these surfaces.

  18. A high-fidelity approach towards simulation of pool boiling

    Science.gov (United States)

    Yazdani, Miad; Radcliff, Thomas; Soteriou, Marios; Alahyari, Abbas A.

    2016-01-01

    A novel numerical approach is developed to simulate the multiscale problem of pool-boiling phase change. The particular focus is to develop a simulation technique that is capable of predicting the heat transfer and hydrodynamic characteristics of nucleate boiling and the transition to critical heat flux on surfaces of arbitrary shape and roughness distribution addressing a critical need to design enhanced boiling heat transfer surfaces. The macro-scale of the phase change and bubble dynamics is addressed through employing off-the-shelf Computational Fluid Dynamics (CFD) methods for interface tracking and interphase mass and energy transfer. The micro-scale of the microlayer, which forms at early stage of bubble nucleation near the wall, is resolved through asymptotic approximation of the thin-film theory which provides a closed-form solution for the distribution of the micro-layer and its influence on the evaporation process. In addition, the sub-grid surface roughness is represented stochastically through probabilistic density functions and its role in bubble nucleation and growth is then represented based on the thermodynamics of nucleation process. This combination of deterministic CFD, local approximation, and stochastic representation allows the simulation of pool boiling on any surface with known roughness and enhancement characteristics. The numerical model is validated for dynamics and hydrothermal characteristics of a single nucleated bubble on a flat surface against available literature data. In addition, the prediction of pool-boiling heat transfer coefficient is verified against experimental measurements as well as reputable correlations for various roughness distributions and different surface orientations. Finally, the model is employed to demonstrate pool-boiling phenomenon on enhanced structures with reentrance cavities and to explore the effect of enhancement feature design on thermal and hydrodynamic characteristics of these surfaces.

  19. Boiling Heat-Transfer Processes and Their Application in the Cooling of High Heat Flux Devices

    Science.gov (United States)

    1993-06-01

    large for very smooth surfaces or highly wettable fluids (e.g., refrigerants or liquid metals) which can lead to explosive boiling (known as bumping) that...of the high wettability of liquid metals, high superheats are normally required to initiate boiling, in some cases having an explosive transition that...About the same time, Staub and Walmet (Ref. 175) identified the two regions before and after the point of significant vapor generation (SNVG) where the

  20. High-speed infrared thermography for the measurement of microscopic boiling parameters on micro- and nano-structured surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Park, Youngjae; Kim, Hyungdae [Kyung Hee Univ., Yongin (Korea, Republic of); Kim, Hyungmo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kim, Joonwon [POSTECH, Pohang (Korea, Republic of)

    2014-10-15

    Micro- and nano-scale structures on boiling surfaces can enhance nucleate boiling heat transfer coefficient (HTC) and critical heat flux (CHF). A few studies were conducted to explain the enhancements of HTC and CHF using the microscopic boiling parameters. Quantitative measurements of microscopic boiling parameters are needed to understand the physical mechanism of the boiling heat transfer augmentation on structured surfaces. However, there is no existing experimental techniques to conveniently measure the boiling parameters on the structured surfaces because of the small (high-speed infrared (IR) thermography to visualize liquid-vapor phase distribution during nucleate pool boiling on micro- and nano-structured surfaces. The visualization results are analyzed to obtain the microscopic boiling parameters. Finally, quantitative microscopic boiling parameters are used to interpret the enhancement of HTC and CHF. In this study, liquid-vapor phase distributions of each surface were clearly visualized by IR thermography during the nucleate boiling phenomena. From the visualization results, following microscopic boiling parameters were quantitatively measured by image processing. - Number density of dry patch, NDP IR thermography technique was demonstrated by nucleate pool boiling experiments with M- and N surfaces. The enhancement of HTC and CHF could be explained by microscopic boiling parameters.

  1. Duality of boiling systems and uncertainty phenomena

    Institute of Scientific and Technical Information of China (English)

    柴立合; 彭晓峰; 王补宣

    2000-01-01

    Interactions among dry patches at high heat flux are theoretically analyzed. The high heat flux boiling experiments on metal plate wall with different materials and thickness are correspondingly conducted. The duality of boiling system, i.e. hydrodynamic performance and self-organized performance is identified. A unified explanation of hydrodynamic models and dry patches models is given. The scatter and uncertainty in boiling data can be mainly attributed to the intrinsic duality, but not the sole surface effects. The present experimental results explain why the deviation point at high flux boiling is seen only on occasion and why the self-organization of dry patches is often ignored in available literature.

  2. High fidelity simulation of nucleate boiling and transition to critical heat flux on enhanced structures

    Science.gov (United States)

    Yazdani, Miad; Alahyari, Abbas; Radcliff, Thomas; Soteriou, Marios

    2015-11-01

    Surface enhancement is often is the primary approach for improved heat transfer performance of two-phase thermal systems particularly when they operate in nucleate boiling regime. This paper exploits the modeling capability developed by Yazdani et al. for simulation of nucleate boiling and transition to critical heat flux to study the nucleation phenomenon on various enhanced structures. The multi-scale of two-phase flow associated with boiling phenomena is addressed through combination of deterministic CFD for the macro-scale transport, asymptotic based representation of micro-layer, and stochastic representation of surface roughness so as to allow a high-fidelity simulation of boiling on an arbitrary surface. In addition, given the excessive complexity of surface structures often used for enhancement of boiling heat transfer, a phase-field-based method is developed to generate the structures where the numerical parameters in the phase-field model determine the topology of a given structure. The ``generated'' structure is then embedded into the two-phase flow model through virtual boundary method for the boiling simulation. The model is validated against experimental data for the boiling curve and the critical heat flux as well as nucleation and bubble dynamics characteristics.

  3. Design and optimization of a novel organic Rankine cycle with improved boiling process

    DEFF Research Database (Denmark)

    Andreasen, Jesper Graa; Larsen, U.; Knudsen, Thomas

    2015-01-01

    In this paper we present a novel organic Rankine cycle layout, named the organic split-cycle, designed for utilization of low grade heat. The cycle is developed by implementing a simplified version of the split evaporation concept from the Kalina split-cycle in the organic Rankine cycle in order....../pentane mixture which, for the 90 °C hot fluid inlet temperature case, achieves a 14.5% higher net power output than an optimized organic Rankine cycle using the same mixture. Two parameter studies suggest that optimum conditions for the organic split-cycle are when the temperature profile allows the minimum...... pinch point temperature difference to be reached at two locations in the boiler. Compared to the transcritical organic Rankine cycle, the organic split-cycle improves the boiling process without an entailing increase in the boiler pressure, thus enabling an efficient low grade heat to power conversion...

  4. Microgravity experiments on boiling and applications: research activity of advanced high heat flux cooling technology for electronic devices in Japan.

    Science.gov (United States)

    Suzuki, Koichi; Kawamura, Hiroshi

    2004-11-01

    Research and development on advanced high heat flux cooling technology for electronic devices has been carried out as the Project of Fundamental Technology Development for Energy Conservation, promoted by the New Energy and Industrial Technology Development Organization of Japan (NEDO). Based on the microgravity experiments on boiling heat transfer, the following useful results have obtained for the cooling of electronic devices. In subcooled flow boiling in a small channel, heat flux increases considerably more than the ordinary critical heat flux with microbubble emission in transition boiling, and dry out of the heating surface is disturbed. Successful enhancement of heat transfer is achieved by a capillary effect from grooved surface dual subchannels on the liquid supply. The critical heat flux increases 30-40 percent more than for ordinary subchannels. A self-wetting mechanism has been proposed, following investigation of bubble behavior in pool boiling of binary mixtures under microgravity. Ideas and a new concept have been proposed for the design of future cooling system in power electronics.

  5. Controlled tissue emulsification produced by high intensity focused ultrasound shock waves and millisecond boiling.

    Science.gov (United States)

    Khokhlova, Tatiana D; Canney, Michael S; Khokhlova, Vera A; Sapozhnikov, Oleg A; Crum, Lawrence A; Bailey, Michael R

    2011-11-01

    In high intensity focused ultrasound (HIFU) applications, tissue may be thermally necrosed by heating, emulsified by cavitation, or, as was recently discovered, emulsified using repetitive millisecond boiling caused by shock wave heating. Here, this last approach was further investigated. Experiments were performed in transparent gels and ex vivo bovine heart tissue using 1, 2, and 3 MHz focused transducers and different pulsing schemes in which the pressure, duty factor, and pulse duration were varied. A previously developed derating procedure to determine in situ shock amplitudes and the time-to-boil was refined. Treatments were monitored using B-mode ultrasound. Both inertial cavitation and boiling were observed during exposures, but emulsification occurred only when shocks and boiling were present. Emulsified lesions without thermal denaturation were produced with shock amplitudes sufficient to induce boiling in less than 20 ms, duty factors of less than 0.02, and pulse lengths shorter than 30 ms. Higher duty factors or longer pulses produced varying degrees of thermal denaturation combined with mechanical emulsification. Larger lesions were obtained using lower ultrasound frequencies. The results show that shock wave heating and millisecond boiling is an effective and reliable way to emulsify tissue while monitoring the treatment with ultrasound.

  6. A QSPR STUDY OF NORMAL BOILING POINT OF ORGANIC COMPOUNDS (ALIPHATIC ALKANES USING MOLECULAR DESCRIPTORS

    Directory of Open Access Journals (Sweden)

    B. Souyei

    2013-12-01

    Full Text Available A quantitative structure–property relationship (QSPR study is carried out to develop correlations that relate the molecular structures of organic compounds (Aliphatic Alkanes to their normal boiling point (NBP and two correlations were proposed for constitutionals and connectivity indices Models. The correlations are simple in application with good accuracy, which provide an easy, direct and relatively accurate way to calculate NBP. Such calculation gives us a model that gives results in remarkable correlations with the descriptors of blokes constitutionals (CON, and connectivity indices (CI (R2 = 0.950, δ = 0.766 (R2 = 0.969, δ = 0.782 respectively.

  7. High-Speed Visualization of Bubble Behaviors for Pool Boiling of R-141b

    Institute of Scientific and Technical Information of China (English)

    Yanhua DIAO; Yaohua ZHAO; Qiuliang WANG

    2006-01-01

    A visualization study on the behavior of bubbles has been carried out for pool boiling of R141b on a horizontal transparent heater at pressure 0.1 MPa. The behaviors of bubbles were recorded by a high-speed camera placed beneath the heater surface. The departure diameter, departure time of bubbles and nucleation site density at different heat flux were obtained. The visualization results show that bubble departure diameter and departure time decrease, while the nucleation site density increases as the heat flux increases. It is also observed that there is no liquid recruited into the microlayer in the experiment. Based on the experimental results, boiling curve for R141b was predicted by using the dynamic microlayer model. As a result, the agreement between the predictive result based on the dynamic microlayer model and the experiment data for boiling curve of R141b is good at high heat flux.

  8. Simulation of high-intensity focused ultrasound lesions in presence of boiling.

    Science.gov (United States)

    Grisey, Anthony; Yon, Sylvain; Letort, Véronique; Lafitte, Pauline

    2016-01-01

    The lesions induced by high-intensity focused ultrasound (HIFU) thermal ablations are particularly difficult to simulate due to the complexity of the involved phenomena. In particular, boiling has a strong influence on the lesion shape. Thus, it must be accounted for if it happens during the pulses to be modeled. However, no acoustic model enables the simulation of the resulting wave scattering. Therefore, we propose an equivalent model for the heat deposition pattern in the presence of boiling. Firstly, the acoustic field is simulated with k-Wave and the heat source term is calculated. Then, a thermal model is designed, including the equivalent model for boiling. It is rigorously calibrated and validated through the use of diversified ex vivo and in vivo data, including usually unexploited data types related to the bubble clouds. The proposed model enabled to efficiently simulate unitary pulses properties, including the sizes of the lesions, their morphology, the boiling onset time, and the influence of the boiling onset time on the lesions sizes. In this article, the whole procedure of model design, calibration, and validation is discussed. In addition to depicting the creative use of data, our modeling approach focuses on the understanding of the mechanisms influencing the shape of the lesion. Further work is required to study the influence of the remaining bubble clouds in the context of pulse groups.

  9. Visualization Study on High Heat Flux Boiling and Critical Heat Flux

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Satbyoul; Kim, Hyungdae [Kyung Hee University, Yongin (Korea, Republic of)

    2015-10-15

    In this study, an integrated visible and infrared-based experimental method is introduced to simultaneously measure the details of high-resolution liquid-vapor phase and heat transfer distributions on a heated wall. The dynamics and heat transfer at high heat flux boiling and critical heat flux were observed. The experiment was conducted in pool of saturated water under atmospheric pressure. There have been many studies to examine the physical mechanisms of nucleation boiling and critical heat flux over several decades. Several visible and infrared-based optical techniques for time-resolved high resolution measurements for liquid-vapor phase and heater surface temperature during boiling have been introduced to understand the characteristics and mechanisms of them. Liquid-vapor phase, temperature, and heat flux distributions on the heated surface were measured during pool boiling of water using the integrated total reflection and infrared thermometry technique. Qualitative examination of the data for high heat flux boiling and CHF was performed. The main contributions of this work are summarized below. The existence and behavior of dry patches lead the way toward CHF condition. Therefore, the mechanistic modeling of the CHF phenomenon necessarily needs to include the physical parameters related to dynamics of the large dry patch such as life time and size. In addition to the dynamic behavior of the dry patch, the thermal behavior of the hot patch is also important. Even though the dry area was rewetted, the stored thermal energy in the hot patch can be remained if the rewetting time is short and the subsequent dry patch is regenerated quickly.

  10. Magnetic resonance imaging of boiling induced by high intensity focused ultrasound.

    Science.gov (United States)

    Khokhlova, Tatiana D; Canney, Michael S; Lee, Donghoon; Marro, Kenneth I; Crum, Lawrence A; Khokhlova, Vera A; Bailey, Michael R

    2009-04-01

    Both mechanically induced acoustic cavitation and thermally induced boiling can occur during high intensity focused ultrasound (HIFU) medical therapy. The goal was to monitor the temperature as boiling was approached using magnetic resonance imaging (MRI). Tissue phantoms were heated for 20 s in a 4.7-T magnet using a 2-MHz HIFU source with an aperture and radius of curvature of 44 mm. The peak focal pressure was 27.5 MPa with corresponding beam width of 0.5 mm. The temperature measured in a single MRI voxel by water proton resonance frequency shift attained a maximum value of only 73 degrees C after 7 s of continuous HIFU exposure when boiling started. Boiling was detected by visual observation, by appearance on the MR images, and by a marked change in the HIFU source power. Nonlinear modeling of the acoustic field combined with a heat transfer equation predicted 100 degrees C after 7 s of exposure. Averaging of the calculated temperature field over the volume of the MRI voxel (0.3 x 0.5 x 2 mm(3)) yielded a maximum of 73 degrees C that agreed with the MR thermometry measurement. These results have implications for the use of MRI-determined temperature values to guide treatments with clinical HIFU systems.

  11. Numerical prediction of nucleate pool boiling heat transfer coefficient under high heat fluxes

    Directory of Open Access Journals (Sweden)

    Pezo Milada L.

    2016-01-01

    Full Text Available This paper presents CFD (Computational Fluid Dynamics approach to prediction of the heat transfer coefficient for nucleate pool boiling under high heat fluxes. Three-dimensional numerical simulations of the atmospheric saturated pool boiling are performed. Mathematical modelling of pool boiling requires a treatment of vapor-liquid two-phase mixture on the macro level, as well as on the micro level, such as bubble growth and departure from the heating surface. Two-phase flow is modelled by the two-fluid model, which consists of the mass, momentum and energy conservation equations for each phase. Interface transfer processes are calculated by the closure laws. Micro level phenomena on the heating surface are modelled with the bubble nucleation site density, the bubble resistance time on the heating wall and with the certain level of randomness in the location of bubble nucleation sites. The developed model was used to determine the heat transfer coefficient and results of numerical simulations are compared with available experimental results and several empirical correlations. A considerable scattering of the predictions of the pool boiling heat transfer coefficient by experimental correlations is observed, while the numerically predicted values are within the range of results calculated by well-known Kutateladze, Mostinski, Kruzhilin and Rohsenow correlations. The presented numerical modeling approach is original regarding both the application of the two-fluid two-phase model for the determination of heat transfer coefficient in pool boiling and the defined boundary conditions at the heated wall surface. [Projekat Ministarstva nauke Republike Srbije, br. 174014

  12. Difference Of Evaporation and Boiling for Heterogeneous Water Droplets in a High-Temperature Gas

    Directory of Open Access Journals (Sweden)

    Legros Jean Claude

    2015-01-01

    Full Text Available Experimental investigation of vapor formation was carried out on water droplets on fixed graphite substrate and heterogeneous droplets (containing solid single inclusions when heating in high-temperature gas. High-speed video shooting (up to 105 frames per second, optical method (Particle Image Velocimetry and TEMA Automotive software were used. We revealed two phase change mechanisms of heterogeneous liquid droplets. Effect of evaporation and boiling on evaporation times of water droplets was determined.

  13. Microwave super-heated boiling of organic liquids: Origin, effect and application

    NARCIS (Netherlands)

    Chemat, F.; Esveld, E.

    2001-01-01

    This paper reports the state of the art of the microwave super-heated boiling phenomenon. When a liquid is heated by microwaves, the temperature increases rapidly to reach a steady temperature while refluxing. It happens that this steady state temperature can be up to 40 K higher than the boiling po

  14. Numerical simulation in a subcooled water flow boiling for one-sided high heat flux in reactor divertor

    Energy Technology Data Exchange (ETDEWEB)

    Liu, P., E-mail: pinliu@aust.edu.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); University of Science and Technology of China, Hefei 230026 (China); School of Mechanical Engineering, Anhui University of Science and Technology, Huainan 232001 (China); Peng, X.B., E-mail: pengxb@ipp.ac.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); Song, Y.T. [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); University of Science and Technology of China, Hefei 230026 (China); Fang, X.D. [Institute of Air Conditioning and Refrigeration, Nanjing University of Aeronautics and Astronautics, Nanjing 210016 (China); Huang, S.H. [University of Science and Technology of China, Hefei 230026 (China); Mao, X. [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China)

    2016-11-15

    Highlights: • The Eulerian multiphase models coupled with Non-equilibrium Boiling model can effectively simulate the subcooled water flow boiling. • ONB and FDB appear earlier and earlier with the increase of heat fluxes. • The void fraction increases gradually along the flow direction. • The inner CuCrZr tube deteriorates earlier than the outer tungsten layer and the middle OFHC copper layer. - Abstract: In order to remove high heat fluxes for plasma facing components in International Thermonuclear Experimental Reactor (ITER) divertor, a numerical simulation of subcooled water flow boiling heat transfer in a vertically upward smooth tube was conducted in this paper on the condition of one-sided high heat fluxes. The Eulerian multiphase model coupled with Non-equilibrium Boiling model was adopted in numerical simulation of the subcooled boiling two-phase flow. The heat transfer regions, thermodynamic vapor quality (x{sub th}), void fraction and temperatures of three components on the condition of the different heat fluxes were analyzed. Numerical results indicate that the onset of nucleate boiling (ONB) and fully developed boiling (FDB) appear earlier and earlier with increasing heat flux. With the increase of heat fluxes, the inner CuCrZr tube will deteriorate earlier than the outer tungsten layer and the middle oxygen-free high-conductivity (OFHC) copper layer. These results provide a valuable reference for the thermal-hydraulic design of a water-cooled W/Cu divertor.

  15. Boiling Heat Transfer in High Temperature Generator of Absorption Chiller/Heater

    Science.gov (United States)

    Furukawa, Masahiro; Enomoto, Eiichi; Sekoguchi, Kotohiko

    The heat transfer performance of forced convective boiling was tested using a high temperature generator of absorption chiller/heater, the rear furnace wall of which was composed of two different surfaces; i. e., plain and sprayed heated surfaces. These two surfaces were bisymmetrically set. Wall surface temperatures of both the fire and fluid sides were measured at three locations along the upward flow direction in each heated surface for determining the heat flux and heat transfer coefficient. Nickel-chromium and alumina were employed as the spray materials. The test results show that the sprayed surface can yield a marked elevation in the heat transfer performance due to boiling on the plain surface. Therefore the level of heated surface temperature is largely reduced by means of the spraying surface treatment. This implies that the spraying would much improve a corrosive condition of the heated surface.

  16. Analysis of heat transfer under high heat flux nucleate boiling conditions

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Y.; Dinh, N. [3145 Burlington Laboratories, Raleigh, NC (United States)

    2016-07-15

    Analysis was performed for a heater infrared thermometric imaging temperature data obtained from high heat flux pool boiling and liquid film boiling experiments BETA. With the OpenFOAM solver, heat flux distribution towards the coolant was obtained by solving transient heat conduction of heater substrate given the heater surface temperature data as boundary condition. The so-obtained heat flux data was used to validate them against the state-of-art wall boiling model developed by D. R. Shaver (2015) with the assumption of micro-layer hydrodynamics. Good agreement was found between the model prediction and data for conditions away from the critical heat flux (CHF). However, the data indicate a different heat transfer pattern under CHF, which is not captured by the current model. Experimental data strengthen the notion of burnout caused by the irreversible hot spot due to failure of rewetting. The observation forms a basis for a detailed modeling of micro-layer hydrodynamics under high heat flux.

  17. Automated high-speed video analysis of the bubble dynamics in subcooled flow boiling

    Energy Technology Data Exchange (ETDEWEB)

    Maurus, Reinhold; Ilchenko, Volodymyr; Sattelmayer, Thomas [Technische Univ. Muenchen, Lehrstuhl fuer Thermodynamik, Garching (Germany)

    2004-04-01

    Subcooled flow boiling is a commonly applied technique for achieving efficient heat transfer. In the study, an experimental investigation in the nucleate boiling regime was performed for water circulating in a closed loop at atmospheric pressure. The test-section consists of a rectangular channel with a one side heated copper strip and a very good optical access. For the optical observation of the bubble behaviour the high-speed cinematography is used. Automated image processing and analysis algorithms developed by the authors were applied for a wide range of mass flow rates and heat fluxes in order to extract characteristic length and time scales of the bubbly layer during the boiling process. Using this methodology, a huge number of bubble cycles could be analysed. The structure of the developed algorithms for the detection of the bubble diameter, the bubble lifetime, the lifetime after the detachment process and the waiting time between two bubble cycles is described. Subsequently, the results from using these automated procedures are presented. A remarkable novelty is the presentation of all results as distribution functions. This is of physical importance because the commonly applied spatial and temporal averaging leads to a loss of information and, moreover, to an unjustified deterministic view of the boiling process, which exhibits in reality a very wide spread of bubble sizes and characteristic times. The results show that the mass flux dominates the temporal bubble behaviour. An increase of the liquid mass flux reveals a strong decrease of the bubble life - and waiting time. In contrast, the variation of the heat flux has a much smaller impact. It is shown in addition that the investigation of the bubble history using automated algorithms delivers novel information with respect to the bubble lift-off probability. (Author)

  18. A Photographic study of subcooled flow boiling burnout at high heat flux and velocity

    Energy Technology Data Exchange (ETDEWEB)

    Celata, G.P.; Mariani, A.; Zummo, G. [ENEA, National Institute of Thermal-Fluid Dynamics, Rome (Italy); Cumo, M. [University of Rome (Italy); Gallo, D. [University of Palermo (Italy). Department of Nuclear Engineering

    2007-01-15

    The present paper reports the results of a visualization study of the burnout in subcooled flow boiling of water, with square cross section annular geometry (formed by a central heater rod contained in a duct characterized by a square cross section). The coolant velocity is in the range 3-10m/s. High speed movies of flow pattern in subcooled flow boiling of water from the onset of nucleate boiling up to physical burnout of the heater are recorded. From video images (single frames taken with a stroboscope light and an exposure time of 1{mu}s), the following general behaviour of vapour bubbles was observed: when the rate of bubble generation is increasing, with bubbles growing in the superheated layer close to the heating wall, their coalescence produces a type of elongated bubble called vapour blanket. One of the main features of the vapour blanket is that it is rooted to the nucleation site on the heated surface. Bubble dimensions are given as a function of thermal-hydraulic tested conditions for the whole range of velocity until the burnout region. A qualitative analysis of the behaviour of four stainless steel heater wires with different macroscopic surface finishes is also presented, showing the importance of this parameter on the dynamics of the bubbles and on the critical heat flux. (author)

  19. A Review of Boiling Heat Transfer Processes at High Heat Flux

    Science.gov (United States)

    1991-04-01

    liquid metals) which can lead to explosive boiling (known as bumping) that can lead to structural damage to hardware. 3 Transition boiling occurs between...to initiate boiling, in some cases having an explosive transition that can cause structural damage to hardware. A thorough understanding of boiling...graphical correlations for the pressure drops encountered in their experiments. About the same time, Staub and Walmet (Ref. 173) identified the two regions

  20. Using Boiling for Treating Waste Activated Sludge

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    In this work we investigated the feasibility of using short time, low superheat boiling to treat biological sludge. The treated sludge exhibited reduced filterability and enhanced settleability. The boiling treatment released a large amount of extra-cellular polymers (ECPs) from the solid phase and reduced the microbial density levels of the total coliform bacteria and the heterotrophic bacteria. A diluted sludge is preferable for its high degree of organic hydrolysis and sufficient reduction in microbial density levels.

  1. High-intensity focused ultrasound monitoring using harmonic motion imaging for focused ultrasound (HMIFU) under boiling or slow denaturation conditions.

    Science.gov (United States)

    Hou, Gary Y; Marquet, Fabrice; Wang, Shutao; Apostolakis, Iason-Zacharias; Konofagou, Elisa E

    2015-07-01

    Harmonic motion imaging for focused ultrasound (HMIFU) is a recently developed high-intensity focused ultrasound (HIFU) treatment monitoring method that utilizes an amplitude-modulated therapeutic ultrasound beam to induce an oscillatory radiation force at the HIFU focus and estimates the focal tissue displacement to monitor the HIFU thermal treatment. In this study, the performance of HMIFU under acoustic, thermal, and mechanical effects was investigated. The performance of HMIFU was assessed in ex vivo canine liver specimens (n = 13) under slow denaturation or boiling regimes. A passive cavitation detector (PCD) was used to assess the acoustic cavitation activity, and a bare-wire thermocouple was used to monitor the focal temperature change. During lesioning with slow denaturation, high quality displacements (correlation coefficient above 0.97) were observed under minimum cavitation noise, indicating the tissue initial-softening-then- stiffening property change. During HIFU with boiling, HMIFU monitored a consistent change in lesion-to-background displacement contrast (0.46 ± 0.37) despite the presence of strong cavitation noise due to boiling during lesion formation. Therefore, HMIFU effectively monitored softening-then-stiffening during lesioning under slow denaturation, and detected lesioning under boiling with a distinct change in displacement contrast under boiling in the presence of cavitation. In conclusion, HMIFU was shown under both boiling and slow denaturation regimes to be effective in HIFU monitoring and lesioning identification without being significantly affected by cavitation noise.

  2. Anti-obesity effects of boiled tuna extract in mice with obesity induced by a high-fat diet.

    Science.gov (United States)

    Kim, Youngmin; Kwon, Mi-Jin; Choi, Jeong-Wook; Lee, Min-Kyeong; Kim, Chorong; Jung, Jaehun; Aprianita, Heny; Nam, Heesop; Nam, Taek-Jeong

    2016-10-01

    The aim of this study was to examine the anti-obesity effects of boiled tuna extract in C57BL/6N mice with obesity induced by a high-fat diet (HFD). We determined the anti-obesity effects of boiled tuna extract (100, 200, or 400 mg/kg) on the progression of HFD-induced obesity for 10 weeks. The mice were divided into 5 groups as follows: the normal diet (ND) group (n=10); the HFD group (n=10); the mice fed HFD and 100 mg/kg boiled tuna extract group (n=10); those fed a HFD and 200 mg/kg boiled tuna extract group (n=10); and those fed a HFD and 400 mg/kg boiled tuna extract group (n=10). Changes in body weight, fat content, serum lipid levels and lipogenic enzyme levels were measured. The consumption of boiled tuna extract lowered epididymal tissue weight and exerted anti-obesity effects, as reflected by the serum glucose, triglyceride (TG), total cholesterol (TC), high-density lipoprotein cholesterol (HDL‑C), low-density lipoprotein cholesterol (LDL-C), insulin and leptin levels. In addition, we demonstrated changes in liver adipogenic- and lipogenic-related protein expression by western blot analysis. Boiled tuna extract downregulated the levels of the CCAAT/enhancer-binding protein α, β and δ (C/EBPα, β, δ), and peroxisome proliferator-activated receptor-γ (PPAR-γ) adipocyte marker genes. Boiled tuna extract also attenuated adipogenic and lipogenic gene expression, namely the levels of fatty acid synthase (FAS), lipoprotein lipase (LPL), acetyl-CoA carboxylase (ACC), glucose transporter type 4 (Glut4) and phosphorylated adenosine monophosphate-activated protein kinase α and β (AMPKα, β) in a dose-dependent manner. Moreover, the consumption of boiled tuna extract restored the levels of superoxide dismutase (SOD), catalase (CAT), glutamic oxaloacetic transaminase (GOT), glutamic-pyruvate transaminase (GPT), aspartate transaminase (AST) and alanine transaminase (ALT) to those of the control group. These results

  3. Void fraction in horizontal bulk flow boiling at high flow qualities

    Energy Technology Data Exchange (ETDEWEB)

    Collado, Fancisco J.; Monne, Carlos [Dpto. de Ingenieria Mecanica, Universidad de Zaragoza-CPS, Maria de Luna 3, 50018-Zaragoza (Spain); Pascau, Antonio [Dpto. de Ciencia de los Materiales y Fluidos, Universidad de Zaragoza-CPS, Maria de Luna 3, 50018-Zaragoza (Spain)

    2008-04-15

    In this work, a new thermodynamic prediction of the vapor void fraction in bulk flow boiling, which is the core process of many energy conversion systems, is analyzed. The current heat balance is based on the flow quality, which is closely related to the measured void fraction, although some correlation for the vapor-liquid velocity ratio is needed. So here, it is suggested to work with the 'static' or thermodynamic quality, which is directly connected to the void fraction through the densities of the phases. Thus, the relation between heat and the mixture enthalpy (here based on the thermodynamic quality instead of the flow one) should be analyzed in depth. The careful void fraction data taken by Thom during the 'Cambridge project' for horizontal saturated flow boiling with high flow qualities ({<=}0.8) have been used for this analysis. As main results, first, we have found that the applied heat and the increment of the proposed thermodynamic enthalpy mixture throughout the heated duct do not agree, and for closure, a parameter is needed. Second, it has been checked that this parameter is practically equal to the classic velocity ratio or 'slip' ratio, suggesting that it should be included in a true thermodynamic heat balance. Furthermore, it has been clearly possible to improve the 'Cambridge project' correlations for the 'slip' ratio, here based on inlet pressure and water velocity, and heat flux. The calculated void fractions compare quite well with the measured ones. Finally, the equivalence of the suggested new heat balance with the current one through the 'slip' ratio is addressed. Highlighted is the same new energetic relation for saturated flow boiling that has been recently confirmed by the authors for Knights data, also taken during the 'Cambridge project', which include not only horizontal but also vertical upwards flows with moderate outlet flow quality ({<=}0.2). (author)

  4. BOILING OF WATER AND ORGANIC LIQUIDS ON LOW-TEMPERATURE POROUS SURFACES OF HEAT PIPES

    OpenAIRE

    Шаповал, Андрій Андрійович; Панов, Євген Миколайович; Сауліна, Юлія Валеріївна; Романчук, Борис Васильович; Трубійчук, Р. П.

    2015-01-01

    The experimental study results of the influence of porous metal fiber structures on the intensity of two-phase heat transfer of water and acetone boiling on porous surfaces in conditions of free movement and capillary transport of liquids are presented in the article. The experiments were realized using specially designed experimental installation simulated the operating conditions of heat pipes and thermosyphons. Such conditions are typical for two-phase heat transfer devices – heat pipes an...

  5. High Intensity Focused Ultrasound Monitoring using Harmonic Motion Imaging for Focused Ultrasound (HMIFU) under boiling or slow denaturation conditions

    Science.gov (United States)

    Hou, Gary Y.; Marquet, Fabrice; Wang, Shutao; Apostolakis, Iason-Zacharias; Konofagou, Elisa E.

    2015-01-01

    Harmonic Motion Imaging for Focused Ultrasound (HMIFU) is a recently developed High-Intensity Focused Ultrasound (HIFU) treatment monitoring method that utilizes an amplitude-modulated therapeutic ultrasound beam to induce an oscillatory radiation force at the HIFU focus and estimates the focal tissue displacement to monitor the HIFU thermal treatment. In this study, the performance of HMIFU under acoustic, thermal and mechanical effects were investigated. The performance of HMIFU was assessed in ex vivo canine liver specimens (n=13) under slow denaturation or boiling regimes. Passive Cavitation Detector (PCD) was used to assess the acoustic cavitation activity while a bare-wire thermocouple was used to monitor the focal temperature change. During lesioning with slow denaturation, high quality displacements (correlation coefficient above 0.97) were observed under minimum cavitation noise, indicating tissue the initial-softening-then-stiffening property change. During HIFU with boiling, HMIFU monitored a consistent change in lesion-to-background displacement contrast (0.46±0.37) despite the presence of strong cavitation noise due to boiling during lesion formation. Therefore, HMIFU effectively monitored softening-then-stiffening during lesioning under slow denaturation, and detected lesioning under boiling with a distinct change in displacement contrast under boiling in the presence of cavitation. In conclusion, HMIFU was shown effective in HIFU monitoring and lesioning identification without being significantly affected by cavitation noise. PMID:26168177

  6. Transient pool boiling heat transfer due to increasing heat inputs in subcooled water at high pressures

    Energy Technology Data Exchange (ETDEWEB)

    Fukuda, K. [Kobe Univ. of Mercantile Marine (Japan); Shiotsu, M.; Sakurai, A. [Kyoto Univ. (Japan)

    1995-09-01

    Understanding of transient boiling phenomenon caused by increasing heat inputs in subcooled water at high pressures is necessary to predict correctly a severe accident due to a power burst in a water-cooled nuclear reactor. Transient maximum heat fluxes, q{sub max}, on a 1.2 mm diameter horizontal cylinder in a pool of saturated and subcooled water for exponential heat inputs, q{sub o}e{sup t/T}, with periods, {tau}, ranging from about 2 ms to 20 s at pressures from atmospheric up to 2063 kPa for water subcoolings from 0 to about 80 K were measured to obtain the extended data base to investigate the effect of high subcoolings on steady-state and transient maximum heat fluxes, q{sub max}. Two main mechanisms of q{sub max} exist depending on the exponential periods at low subcoolings. One is due to the time lag of the hydrodynamic instability which starts at steady-state maximum heat flux on fully developed nucleate boiling (FDNB), and the other is due to the heterogenous spontaneous nucleations (HSN) in flooded cavities which coexist with vapor bubbles growing up from active cavities. The shortest period corresponding to the maximum q{sub max} for long period range belonging to the former mechanism becomes longer and the q{sub max}mechanism for long period range shifts to that due the HSN on FDNB with the increase of subcooling and pressure. The longest period corresponding to the minimum q{sub max} for the short period range belonging to the latter mechanism becomes shorter with the increase in saturated pressure. On the contrary, the longest period becomes longer with the increase in subcooling at high pressures. Correlations for steady-state and transient maximum heat fluxes were presented for a wide range of pressure and subcooling.

  7. Shock-induced heating and millisecond boiling in gels and tissue due to high intensity focused ultrasound.

    Science.gov (United States)

    Canney, Michael S; Khokhlova, Vera A; Bessonova, Olga V; Bailey, Michael R; Crum, Lawrence A

    2010-02-01

    Nonlinear propagation causes high-intensity ultrasound waves to distort and generate higher harmonics, which are more readily absorbed and converted to heat than the fundamental frequency. Although such nonlinear effects have been investigated previously and found to not significantly alter high-intensity focused ultrasound (HIFU) treatments, two results reported here change this paradigm. One is that at clinically relevant intensity levels, HIFU waves not only become distorted but form shock waves in tissue. The other is that the generated shock waves heat the tissue to boiling in much less time than predicted for undistorted or weakly distorted waves. In this study, a 2-MHz HIFU source operating at peak intensities up to 25,000 W/cm(2) was used to heat transparent tissue-mimicking phantoms and ex vivo bovine liver samples. Initiation of boiling was detected using high-speed photography, a 20-MHz passive cavitation detector and fluctuation of the drive voltage at the HIFU source. The time to boil obtained experimentally was used to quantify heating rates and was compared with calculations using weak shock theory and the shock amplitudes obtained from nonlinear modeling and measurements with a fiber optic hydrophone. As observed experimentally and predicted by calculations, shocked focal waveforms produced boiling in as little as 3 ms and the time to initiate boiling was sensitive to small changes in HIFU output. Nonlinear heating as a result of shock waves is therefore important to HIFU, and clinicians should be aware of the potential for very rapid boiling because it alters treatments.

  8. Biomass to fuels : Upgrading of flash pyrolysis oil by reactive distillation using a high boiling alcohol and acid catalysts

    NARCIS (Netherlands)

    Mahfud, F.H.; Melian Cabrera, I.V.; Manurung, R.M.; Heeres, H.J.

    2007-01-01

    We here report our studies on the upgrading of flash pyrolysis oil using an improved alcohol treatment method. The method consists of treating pyrolysis oil with a high boiling alcohol like n-butanol in the presence of a (solid) acid catalyst at 323-353 K under reduced pressure (<10 kPa). Using this

  9. Development of a high-performance boiling heat exchanger by improved liquid supply to narrow channels.

    Science.gov (United States)

    Ohta, Haruhiko; Ohno, Toshiyuki; Hioki, Fumiaki; Shinmoto, Yasuhisa

    2004-11-01

    A two-phase flow loop is a promising method for application to thermal management systems for large-scale space platforms handling large amounts of energy. Boiling heat transfer reduces the size and weight of cold plates. The transportation of latent heat reduces the mass flow rate of working fluid and pump power. To develop compact heat exchangers for the removal of waste heat from electronic devices with high heat generation density, experiments on a method to increase the critical heat flux for a narrow heated channel between parallel heated and unheated plates were conducted. Fine grooves are machined on the heating surface in a transverse direction to the flow and liquid is supplied underneath flattened bubbles by the capillary pressure difference from auxiliary liquid channels separated by porous metal plates from the main heated channel. The critical heat flux values for the present heated channel structure are more than twice those for a flat surface at gap sizes 2 mm and 0.7 mm. The validity of the present structure with auxiliary liquid channels is confirmed by experiments in which the liquid supply to the grooves is interrupted. The increment in the critical heat flux compared to those for a flat surface takes a maximum value at a certain flow rate of liquid supply to the heated channel. The increment is expected to become larger when the length of the heated channel is increased and/or the gravity level is reduced.

  10. Ethylene diamine-assisted synthesis of iron oxide nanoparticles in high-boiling polyolys.

    Science.gov (United States)

    Arndt, Darius; Zielasek, Volkmar; Dreher, Wolfgang; Bäumer, Marcus

    2014-03-01

    The decomposition of iron(III) acetylacetonate in high-boiling polyols such as diethylene glycole is an efficient way to produce water-soluble iron oxide nanoparticles (IONPs) with small sizes. We present an extension of this method by introducing ethylene diamine (EDA) or diethylene triamine (DTA) as a structure-directing agent and adding polyvinylpyrrolidone (PVP) as a stabilizing agent. The synthesis was studied with respect to effects of the chain length of the polyol used as solvent, the chain length of the structure-directing agent, the presence of PVP, the heating rate, and the nature of the precursor. By varying these parameters, we were able to show, that probably an interplay of the structure-directing agent and the polyol plays an important role for the stabilization and growth of the different facets of the IONP crystal. The chain length of the polyol used as solvent alters the influence of EDA or DTA as stabilizer of {111} facets, leading to IONPs with spherical, tetrahedral, or nanoplate morphology and mean diameters ranging from 4 nm up to 25 nm. PVP in the reaction medium narrows down particle size and shape distributions and promotes the formation of very stable, water-based colloidal solutions. The saturation magnetization of the particles was determined by a superconducting quantum interference device (SQUID) and their ability to act as a T2-contrast agent was tested by magnetic resonance imaging (MRI). Copyright © 2013 Elsevier Inc. All rights reserved.

  11. A high-fidelity approach towards heat transfer prediction of pool boiling

    Science.gov (United States)

    Yazdani, Miad; Alahyari, Abbas; Radcliff, Thomas

    2014-11-01

    A novel numerical approach is developed to simulate the multiscale problem of pool-boiling phase change with an unprecedented fidelity and cost. The particular focus is to predict the heat transfer coefficient of pool-boiling regime and its transition to critical heat flux on surfaces of arbitrary shape and roughness distribution. The large-scale of the phase change and bubble dynamics is addressed through employing off-the-shelf methods for interface tracking and interphase mass and energy transfer. The small-scale of the microlayer which forms at early stage of bubble nucleation is resolved through asymptotic approximation of the thin-film theory which provides a closed-form solution for the distribution of the micro-layer and its influence on the evaporation process. In addition, the surface roughness and its role in bubble nucleation and growth is represented based on thermodynamics of nucleation process which allows the simulation of pool boiling on any surface with known roughness and enhancement characteristics. The numerical model is validated for dynamics and hydrothermal characteristics of a single nucleated bubble on a flat surface against available literature data. In addition, the model's prediction of pool-boiling heat transfer coefficient is verified against reputable correlations for various roughness distributions and different surface alignment. Finally, the model is employed to demonstrate pool-boiling phenomenon on enhanced structures with reentrance cavities and to explore the effect of enhancement features on thermal and hydrodynamic characteristics of these surfaces.

  12. Nucleate pool boiling: High gravity to reduced gravity; liquid metals to cryogens

    Science.gov (United States)

    Merte, Herman, Jr.

    1988-01-01

    Requirements for the proper functioning of equipment and personnel in reduced gravity associated with space platforms and future space station modules introduce unique problems in temperature control; power generation; energy dissipation; the storage, transfer, control and conditioning of fluids; and liquid-vapor separation. The phase change of boiling is significant in all of these. Although both pool and flow boiling would be involved, research results to date include only pool boiling because buoyancy effects are maximized for this case. The effective application of forced convection boiling heat transfer in the microgravity of space will require a well grounded and cogent understanding of the mechanisms involved. Experimental results are presented for pool boiling from a single geometrical configuration, a flat surface, covering a wide range of body forces from a/g = 20 to 1 to a/g = 0 to -1 for a cryogenic liquid, and from a/g = 20 to 1 for water and a liquid metal. Similarities in behavior are noted for these three fluids at the higher gravity levels, and may reasonably be expected to continue at reduced gravity levels.

  13. Effects of boiling duration in processing of White Paeony Root on its overall quality evaluated by ultra-high performance liquid chromatography quadrupole/time-of-flight mass spectrometry based metabolomics analysis and high performance liquid chromatography quantification.

    Science.gov (United States)

    Ming, Kong; Xu, Jun; Liu, Huan-Huan; Xu, Jin-Di; Li, Xiu-Yang; Lu, Min; Wang, Chun-Ru; Chen, Hu-Biao; Li, Song-Lin

    2017-01-01

    Boiling processing is commonly used in post-harvest handling of White Paeony Root (WPR), in order to whiten the herbal materials and preserve the bright color, since such WPR is empirically considered to possess a higher quality. The present study was designed to investigate whether and how the boiling processing affects overall quality of WPR. First, an ultra-high performance liquid chromatography quadrupole/time-of-flight mass spectrometry-based metabolomics approach coupled with multivariate statistical analysis was developed to compare the holistic quality of boiled and un-boiled WPR samples. Second, ten major components in WPR samples boiled for different durations were quantitatively determined using high performance liquid chromatography to further explore the effects of boiling time on the holistic quality of WPR, meanwhile the appearance of the processed herbal materials was observed. The results suggested that the boiling processing conspicuously affected the holistic quality of WPR by simultaneously and inconsistently altering the chemical compositions and that short-time boiling processing between 2 and 10 min could both make the WPR bright-colored and improve the contents of major bioactive components, which were not achieved either without boiling or with prolonged boiling. In conclusion, short-term boiling (2-10 min) is recommended for post-harvest handling of WPR.

  14. Boiling Heat Transfer Measurements on Highly Conductive Surfaces Using Microscale Heater and Temperature Arrays

    Science.gov (United States)

    Kim, J.; Bae, S. W.; Whitten, M. W.; Mullen, J. D.; Quine, R. W.; Kalkur, T. S.

    1999-01-01

    Two systems have been developed to study boiling heat transfer on the microscale. The first system utilizes a 32 x 32 array of diodes to measure the local temperature fluctuations during boiling on a silicon wafer heated from below. The second system utilizes an array of 96 microscale heaters each maintained at constant surface temperature using electronic feedback loops. The power required to keep each heater at constant temperature is measured, enabling the local heat transfer coefficient to be determined. Both of these systems as well as some preliminary results are discussed.

  15. 硅烷高沸物的综合利用%Comprehensive utilization of high boiling silane

    Institute of Scientific and Technical Information of China (English)

    刘玲

    2000-01-01

    介绍了合成有机硅过程中产生的硅烷高沸物的组成、处理方法及其综合利用技术进展情况。简述了利用硅烷高沸物制备单硅烷、硅油、有机硅防水剂、有机硅树脂、消泡剂等产品的生产方法及技术特点。%The advances of components, treatment and comprehensive utilization of high boiling silane resulting from the synthesis of organo-silicone were introduced. The production methods and technical features of monosilane, silicone oil, silicone water-proofing agent and silicone resin using the high boiling silane were described.

  16. Design and optimization of a novel organic Rankine cycle with improved boiling process

    DEFF Research Database (Denmark)

    Andreasen, Jesper Graa; Larsen, U.; Knudsen, Thomas;

    2015-01-01

    In this paper we present a novel organic Rankine cycle layout, named the organic split-cycle, designed for utilization of low grade heat. The cycle is developed by implementing a simplified version of the split evaporation concept from the Kalina split-cycle in the organic Rankine cycle in order...

  17. Histological and biochemical analysis of mechanical and thermal bioeffects in boiling histotripsy lesions induced by high intensity focused ultrasound.

    Science.gov (United States)

    Wang, Yak-Nam; Khokhlova, Tatiana; Bailey, Michael; Hwang, Joo Ha; Khokhlova, Vera

    2013-03-01

    Recent studies have shown that shockwave heating and millisecond boiling in high-intensity focused ultrasound fields can result in mechanical fractionation or emulsification of tissue, termed boiling histotripsy. Visual observations of the change in color and contents indicated that the degree of thermal damage in the emulsified lesions can be controlled by varying the parameters of the exposure. The goal of this work was to examine thermal and mechanical effects in boiling histotripsy lesions using histologic and biochemical analysis. The lesions were induced in ex vivo bovine heart and liver using a 2-MHz single-element transducer operating at duty factors of 0.005-0.01, pulse durations of 5-500 ms and in situ shock amplitude of 73 MPa. Mechanical and thermal damage to tissue was evaluated histologically using conventional staining techniques (hematoxylin and eosin, and nicotinamide adenine dinucleotide-diaphorase). Thermal effects were quantified by measuring denaturation of salt soluble proteins in the treated region. According to histologic analysis, the lesions that visually appeared as a liquid contained no cellular structures larger than a cell nucleus and had a sharp border of one to two cells. Both histologic and protein analysis showed that lesions obtained with short pulses (thermal damage. Increasing the pulse duration resulted in an increase in thermal damage. However, both protein analysis and nicotinamide adenine dinucleotide-diaphorase staining showed less denaturation than visually observed as whitening of tissue. The number of high-intensity focused ultrasound pulses delivered per exposure did not change the lesion shape or the degree of thermal denaturation, whereas the size of the lesion showed a saturating behavior suggesting optimal exposure duration. This study confirmed that boiling histotripsy offers an effective, predictable way to non-invasively fractionate tissue into sub-cellular fragments with or without inducing thermal damage.

  18. PREDICTION OF THE VAPOR PRESSURE, BOILING POINT, HEAT OF VAPORIZATION AND DIFFUSION COEFFICIENT OF ORGANIC COMPOUNDS

    Science.gov (United States)

    The prototype computer program SPARC has been under development for several years to estimate physical properties and chemical reactivity parameters of organic compounds strictly from molecular structure. SPARC solute-solute physical process models have been developed and tested...

  19. Oscillate Boiling

    CERN Document Server

    Li, Fenfang; Nguyen, Dang Minh; Ohl, Claus-Dieter

    2016-01-01

    We report about an intriguing boiling regime occurring for small heaters embedded on the boundary in subcooled water. The microheater is realized by focusing a continuous wave laser beam to about $10\\,\\mu$m in diameter onto a 165\\,nm-thick layer of gold, which is submerged in water. After an initial vaporous explosion a single bubble oscillates continuously and repeatably at several $100\\,$kHz. The microbubble's oscillations are accompanied with bubble pinch-off leading to a stream of gaseous bubbles into the subcooled water. The self-driven bubble oscillation is explained with a thermally kicked oscillator caused by the non-spherical collapses and by surface pinning. Additionally, Marangoni stresses induce a recirculating streaming flow which transports cold liquid towards the microheater reducing diffusion of heat along the substrate and therefore stabilizing the phenomenon to many million cycles. We speculate that this oscillate boiling regime may allow to overcome the heat transfer thresholds observed dur...

  20. BOILING REACTORS

    Science.gov (United States)

    Untermyer, S.

    1962-04-10

    A boiling reactor having a reactivity which is reduced by an increase in the volume of vaporized coolant therein is described. In this system unvaporized liquid coolant is extracted from the reactor, heat is extracted therefrom, and it is returned to the reactor as sub-cooled liquid coolant. This reduces a portion of the coolant which includes vaporized coolant within the core assembly thereby enhancing the power output of the assembly and rendering the reactor substantially self-regulating. (AEC)

  1. Experimental investigation of film boiling on spheres using high-speed video

    Directory of Open Access Journals (Sweden)

    Fedoseenko Ivan

    2012-04-01

    Full Text Available The experimental investigation of saturated Freon-113 film boiling on spheres with different diameters at atmospheric pressure under conditions of free convection is executed. It was found that with increasing diameter of the sphere and the temperature difference is changing the wave motion of the vapor film with two-dimensional to three-dimensional mode. Also, found that in a range of regime parameters at which observed a three-dimensional interface motion, the destruction method of two-dimensional wave is similar to a series of three or more waves. I.e. was some system memory. When the temperature difference close to critical after the passage of a wave are possible the local contacts of liquid with a heated surface of the sphere. However, these contacts do not lead to degradation of the wave motion of the interface, and the film boiling crisis of saturated Freon-113 occurs smoothly in contrast to the crisis at boiling of saturated and subcooled water.

  2. Boiling liquid cauldron status report

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, M.A.

    1980-12-28

    The progress made over the past year in assessing the feasibility of the high-temperature, boiling cauldron blanket concept for the tanden mirror reactor is reviewed. The status of the proposed experiments and recently revised estimates of the vapor void fraction in the boiling pool are discussed.

  3. Measurement of nucleation site density, bubble departure diameter and frequency in pool boiling of water using high-speed infrared and optical cameras

    Energy Technology Data Exchange (ETDEWEB)

    Gerardi, Craig; Buongiorno, Jacopo; Hu, Lin-wen; McKrell, Thomas [Massachusetts Institute of Technology, Cambridge, MA (United States)], e-mail: jacopo@mit.edu

    2009-07-01

    A high-speed video and IR thermometry based technique has been used to obtain time and space resolved information on bubble nucleation and boiling heat transfer. This approach provides a fundamental and systematic method for investigating nucleate boiling in a very detailed fashion. Data on bubble departure diameter and frequency, growth and wait times, and nucleation site density are measured with relative ease. The data have been compared to the traditional decades-old and poorly-validated nucleate-boiling models and correlations. The agreement between the data and the models is relatively good. This study also shows that new insights into boiling heat transfer mechanisms can be obtained with the present technique. For example, our data and analysis suggest that a large contribution to bubble growth comes from heat transfer through the superheated liquid layer in addition to micro layer evaporation. (author)

  4. Pool boiling with high heat flux enabled by a porous artery structure

    Science.gov (United States)

    Bai, Lizhan; Zhang, Lianpei; Lin, Guiping; Peterson, G. P.

    2016-06-01

    A porous artery structure utilizing the concept of "phase separation and modulation" is proposed to enhance the critical heat flux of pool boiling. A series of experiments were conducted on a range of test articles in which multiple rectangular arteries were machined directly into the top surface of a 10.0 mm diameter copper rod. The arteries were then covered by a 2.0 mm thickness microporous copper plate through silver brazing. The pool wall was fabricated from transparent Pyrex glass to allow a visualization study, and water was used as the working fluid. Experimental results confirmed that the porous artery structure provided individual flow paths for the liquid supply and vapor venting, and avoided the detrimental effects of the liquid/vapor counter flow. As a result, a maximum heat flux of 610 W/cm2 over a heating area of 0.78 cm2 was achieved with no indication of dryout, prior to reaching the heater design temperature limit. Following the experimental tests, the mechanisms responsible for the boiling critical heat flux and performance enhancement of the porous artery structure were analyzed.

  5. 离子液体-顶空气相色谱法检测酮康唑中的多种高沸点有机残留溶剂%ILs as Headspace Matrix Medium for Determining High-boiling Organic Residual Solvent in Ketoconazole by HS-GC

    Institute of Scientific and Technical Information of China (English)

    李韶勇; 张琳; 倪美萍; 蒋晔

    2013-01-01

    ILs.The headspace vial was sealed and radiated under 150 W of microwave power for 75 s to accelarate the dissolution of Ketoconanzale.The sample solution was mainteined at the equilibration temperatute of 110 ℃ for 30 min and a volume of 1 mL headspace gas was directly injected into GC for analysis.A phenomenex ZB-1 capillary column (0.53 mm×60 m) with 5.00 μm film thickness was utilized for chromatographic separation of the solvents with FID as detector.A temperature programme was also employed.RESULTS An excellent seperation of ethanol,dichloromethane,ethyl acetate,butyl alcohol,pyridine,DMF and DMSO was achieved.The calibration curve was linear in the range of 1.25-200 mg·L-1 for ethanol,1.50-24.0 mg·L-1 for dichloromethane,12.5-200 mg·L-1 for ethyl acetate,12.5-200 mg·L-1 for butyl alcohol,0.500-8.00 mg·L-1 for pyridine,2.20-3.52 mg·L-1 for DMF and 12.5-200 mg·L-1 for DMSO.All the average recovery were limited in 89.8%-98.2% and RSD were less than 4.0%.For ethyl,the headspace efficiency of ILs increased with the growth of cation alkyl chain.For ethyl,DMF and DMSO,the headspace efficiency of ILs decreased with the growth of cation alkyl chain.However,the anion of ILs has minor impact on headspace efficiency.Ultimately,[Bmim][PF6] was chosen as the best headspace solvent.CONCLUSION The proposed method is easy,fast and sensitive.It is suitable for the simultaneous determination of ethanol,dichloromethane,ethyl acetate,butyl alcohol,pyridine,DMF and DMSO in Ketoconanzale,providing a new mean for the detection of residual solvent with high-boiling point.The headspace efficiency of ILs increased with the decrease of the cationic polarity for protic solvents and reduced with the decrease of cation polarity for aprotic solvents with nucleophilic ability,while the polarity of the anion has little influence on headspace efficiency.The results above mentioned provides a reference for choosing suitable ILs as headspace solvent to determinate residual solvent.

  6. Cooling of high power LED chip by boiling on the longitudinal finned surfaces

    Directory of Open Access Journals (Sweden)

    Shatskiy Evgeniy

    2016-01-01

    Full Text Available In this work, we have created a new experimental setup for studying heat transfer from a local heat source. The boiling heat transfer on the local heaters with a diameter of 5 and 1 mm has been investigated. It is shown that on the finned surfaces the overheating relative to the saturation temperature in comparison with a smooth surface decreases up to three times for the heater with a diameter of 5 mm. There is up to two times increase in heat transfer coefficient on finned surfaces as compared to the smooth ones. For finned surfaces on the heater with a diameter of 1 mm the surface overheating relative to the saturation temperature decreases in four times. More than three times increase is observed for the heat transfer coefficient on finned surfaces as compared to the smooth ones.

  7. Design Technique for the High-Boiling Propellant Storage and Preparation Facility at the Cosmodrome «Vostochny»

    Directory of Open Access Journals (Sweden)

    O. E. Denisov

    2014-01-01

    to tanks of the rocket-carriers through the pipeline.A direct supply of the prepared component to the rocket-carrier tanks allows a significantly decreasing equipment demand at the launch complex (LC owing to almost full abandonment of the near-launch storehouses and propellant-feed systems.The pipeline fuel remnants are discharged through the branch in the sump from which fuel can be directed to the storage capacities to have its future preparation again.Existing LC versus LC with the storage facility:- Each LC has a separate near-launch storehouse;- Each near-launch storehouse contains several charges to feed fuel tanks of rocket-carrier;- Each LC has the unique systems of propellant preparation.Application of storage facility:- storage facility allows bulk receipt and storage of high-boiling propellant to meet needs of all LC of the spaceport;- there are all means at the storage facility to prepare high-boiling propellant in all required parameters;- high-boiling propellant can be supplied from the storage facility using both transport capacities, and pipelines directly to the rocket-carrier tanks.Advantages:+ possibility to receive and store the bulk high-boiling propellant+ decreasing total demand of technological systems+ simplified spaceport infrastructureDisadvantages:- decreasing reliability rates caused by a lack of reservation of technological systems

  8. High reliability organizations

    NARCIS (Netherlands)

    Gallis, R.; Zwetsloot, G.I.J.M.

    2014-01-01

    High Reliability Organizations (HRO’s) are organizations that constantly face serious and complex (safety) risks yet succeed in realising an excellent safety performance. In such situations acceptable levels of safety cannot be achieved by traditional safety management only. HRO’s manage safety

  9. Assessing the mammalian toxicity of high-boiling petroleum substances under the rubric of the HPV program.

    Science.gov (United States)

    Gray, Thomas M; Simpson, Barry J; Nicolich, Mark J; Murray, F Jay; Verstuyft, Allen W; Roth, Randy N; McKee, Richard H

    2013-11-01

    In 1998, the US EPA announced the HPV Challenge Program, a voluntary chemical data collection effort. The Petroleum HPV Testing Group (PHPVTG(1)) volunteered to provide data on approximately 110 high boiling petroleum substances (HBPS), i.e. substances with final boiling points ≥ approximately 650°F (343°C). These HBPS are substances of unknown and variable composition (UVCBs) that are composed of numerous individual constituents. Toxicity studies have shown that some HBPS can produce systemic (repeat-dose) and developmental effects, and some are mutagenic under in vitro conditions. The papers in this supplement show that these effects are related to the profiles of aromatic constituents in these substances. Further, it is shown that the effects on selected repeat-dose and developmental toxicity endpoints and mutagenic activity in bacterial assays can be predicted from compositional information using models based on the aromatic-ring class profile, "ARC profile" as defined by gas chromatographic separation of the DMSO-soluble fraction of the starting materials. This chromatographic method and the predictive models provide an efficient means of characterizing for screening purposes the potential for repeat-dose, developmental effects and bacterial mutagenicity of HBPS and can reduce the number of animal tests that would be required if these tests were conducted on all 110 HBPS. Copyright © 2012. Published by Elsevier Inc.

  10. Intensive evaporation and boiling of a heterogeneous liquid droplet with an explosive disintegration in high-temperature gas area

    Directory of Open Access Journals (Sweden)

    Piskunov Maxim V.

    2016-01-01

    Full Text Available The using of the high-speed (not less than 105 frames per second video recording tools (“Phantom” and the software package ("TEMA Automotive" allowed carrying out an experimental research of laws of intensive vaporization with an explosive disintegration of heterogeneous (with a single solid nontransparent inclusion liquid droplet (by the example of water in high-temperature (500-800 K gases (combustion products. Times of the processes under consideration and stages (liquid heat-up, evaporation from an external surface, bubble boiling at internal interfaces, growth of bubble sizes, explosive droplet breakup were established. Necessary conditions of an explosive vaporization of a heterogeneous droplet were found out. Mechanisms of this process and an influence of properties of liquid and inclusion material on them were determined.

  11. Developmental toxicity following oral administration of a high-boiling coal liquid to pregnant rats

    Energy Technology Data Exchange (ETDEWEB)

    Hackett, P.L.; Rommereim, D.N.; Sikov, M.R.

    1984-01-01

    Heavy distillate (HD), the highest-boiling coal liquid from the solvent-refined coal-II process (SRC-II), was administered by intragastric (IG) intubation to pregnant rats. Five dose levels of HD (0.09, 0.14, 0.18, 0.36 and 0.74 g kg/sup -1/), were given daily from 12 to 16 days of gestation and the rats were killed at 20 days of gestation. Maternal body weights and weights of the liver, kidneys, spleen, adrenals, thymus, ovaries and the gravid uterus were obtained. Gravid uteri were evaluated for prenatal mortality. Live fetuses were examined for malformations and weighed; fetal lungs were excised and weighed. Maternal (extragestational) weight gains and thymic weights diminished in all groups that received the SRC material. Adrenal weights were increased in all treated animals, except for those in the lowest-dose group (0.9 g kg/sup -1/). There was significant maternal mortality at 0.74 g kg/sup -1/ and increased intrauterine mortality at doses of 0.37 and 0.74 g kg/sup -1/. Placental weight was depressed, and the incidence of fetal anomalies was increased at 0.14 g kg/sup -1/ and all higher dose levels. 19 references, 1 figure, 5 tables.

  12. Enhanced heat transfer in confined pool boiling

    Energy Technology Data Exchange (ETDEWEB)

    Rops, C.M. [TNO Science and Industry, P.O. Box 155, 2600 AD Delft (Netherlands)], E-mail: cor.rops@tno.nl; Lindken, R. [Laboratory for Aero and Hydrodynamics, Delft University of Technology (Netherlands); Velthuis, J.F.M. [TNO Science and Industry, P.O. Box 155, 2600 AD Delft (Netherlands); Westerweel, J. [Laboratory for Aero and Hydrodynamics, Delft University of Technology (Netherlands)

    2009-08-15

    We report the results of an experimental investigation of the heat transfer during nucleate boiling on a spatially confined boiling surface. The heat flux as a function of the boiling surface temperature was measured in pool boiling pots with diameters ranging from 15 mm down to 4.5 mm. It was found that a reduction of the pool diameter leads to an enhancement of the nucleate boiling heat flux for most of the boiling curve. Our experimental results indicate that this enhancement is not affected by the depth of the boiling pot, the material of the bounding wall, or the diameter of the inlet water supply. High-speed camera imaging shows that the heat transfer enhancement for the spatially confined pool boiling occurs in conjunction with a stable circulating flow, which is in contrast to the chaotic and mainly upward motion for boiling in larger pool diameters. An explanation for the enhancement of the heat transfer and the associated change in flow pattern is found in the singularisation of the nucleate boiling process.

  13. A study of boiling heat transfer as applied to the cooling of ball bearings in the high pressure oxygen turbopump of the space shuttle main engine

    Science.gov (United States)

    Schreiber, Will

    1986-01-01

    Two sets of ball bearings support the main shaft within the High Pressure Oxygen Turbopump (HPOTP) in the Space Shuttle Main Engine (SSME). In operation, these bearings are cooled and lubricated with high pressure liquid oxygen (LOX) flowing axially through the bearing assembly. Currently, modifications in the assembly design are being contemplated in order to enhance the lifetime of the bearings and to allow the HPOTP to operate under larger loads. An understanding of the fluid dynamics and heat transfer characteristics of the flowing LOX is necessary for the implementation of these design changes. The proposed computational model of the LOX fluid dynamics, in addition to dealing with a turbulent flow in a complex geometry, must address the complication associated with boiling and two-phase flow. The feasibility of and possible methods for modeling boiling heat transfer are considered. The theory of boiling as pertains to this particular problem is reviewed. Recommendations are given for experiments which would be necessary to establish validity for correlations needed to model boiling.

  14. Instability in flow boiling in microchannels

    CERN Document Server

    Saha, Sujoy Kumar

    2016-01-01

    This Brief addresses the phenomena of instability in flow boiling in microchannels occurring in high heat flux electronic cooling. A companion edition in the SpringerBrief Subseries on Thermal Engineering and Applied Science to “Critical Heat Flux in Flow Boiling in Microchannels,” and "Heat Transfer and Pressure Drop in Flow Boiling in Microchannels,"by the same author team, this volume is idea for professionals, researchers, and graduate students concerned with electronic cooling.

  15. A low viscosity, low boiling point, clean solvent system for the rapid crystallisation of highly specular perovskite films

    Energy Technology Data Exchange (ETDEWEB)

    Noel, Nakita K.; Habisreutinger, Severin N.; Wenger, Bernard; Klug, Matthew T.; Hörantner, Maximilian T.; Johnston, Michael B.; Nicholas, Robin J.; Moore, David T.; Snaith, Henry J.

    2017-01-01

    Perovskite-based photovoltaics have, in recent years, become poised to revolutionise the solar industry. While there have been many approaches taken to the deposition of this material, one-step spin-coating remains the simplest and most widely used method in research laboratories. Although spin-coating is not recognised as the ideal manufacturing methodology, it represents a starting point from which more scalable deposition methods, such as slot-dye coating or ink-jet printing can be developed. Here, we introduce a new, low-boiling point, low viscosity solvent system that enables rapid, room temperature crystallisation of methylammonium lead triiodide perovskite films, without the use of strongly coordinating aprotic solvents. Through the use of this solvent, we produce dense, pinhole free films with uniform coverage, high specularity, and enhanced optoelectronic properties. We fabricate devices and achieve stabilised power conversion efficiencies of over 18% for films which have been annealed at 100 degrees C, and over 17% for films which have been dried under vacuum and have undergone no thermal processing. This deposition technique allows uniform coating on substrate areas of up to 125 cm2, showing tremendous promise for the fabrication of large area, high efficiency, solution processed devices, and represents a critical step towards industrial upscaling and large area printing of perovskite solar cells.

  16. Pyrosequencing reveals high-temperature cellulolytic microbial consortia in Great Boiling Spring after in situ lignocellulose enrichment.

    Directory of Open Access Journals (Sweden)

    Joseph P Peacock

    Full Text Available To characterize high-temperature cellulolytic microbial communities, two lignocellulosic substrates, ammonia fiber-explosion-treated corn stover and aspen shavings, were incubated at average temperatures of 77 and 85°C in the sediment and water column of Great Boiling Spring, Nevada. Comparison of 109,941 quality-filtered 16S rRNA gene pyrosequences (pyrotags from eight enrichments to 37,057 quality-filtered pyrotags from corresponding natural samples revealed distinct enriched communities dominated by phylotypes related to cellulolytic and hemicellulolytic Thermotoga and Dictyoglomus, cellulolytic and sugar-fermenting Desulfurococcales, and sugar-fermenting and hydrogenotrophic Archaeoglobales. Minor enriched populations included close relatives of hydrogenotrophic Thermodesulfobacteria, the candidate bacterial phylum OP9, and candidate archaeal groups C2 and DHVE3. Enrichment temperature was the major factor influencing community composition, with a negative correlation between temperature and richness, followed by lignocellulosic substrate composition. This study establishes the importance of these groups in the natural degradation of lignocellulose at high temperatures and suggests that a substantial portion of the diversity of thermophiles contributing to consortial cellulolysis may be contained within lineages that have representatives in pure culture.

  17. Novel thermal management system using boiling cooling for high-powered lithium-ion battery packs for hybrid electric vehicles

    Science.gov (United States)

    Al-Zareer, Maan; Dincer, Ibrahim; Rosen, Marc A.

    2017-09-01

    A thermal management system is necessary to control the operating temperature of the lithium ion batteries in battery packs for electrical and hybrid electrical vehicles. This paper proposes a new battery thermal management system based on one type of phase change material for the battery packs in hybrid electrical vehicles and develops a three dimensional electrochemical thermal model. The temperature distributions of the batteries are investigated under various operating conditions for comparative evaluations. The proposed system boils liquid propane to remove the heat generated by the batteries, and the propane vapor is used to cool the part of the battery that is not covered with liquid propane. The effect on the thermal behavior of the battery pack of the height of the liquid propane inside the battery pack, relative to the height of the battery, is analyzed. The results show that the propane based thermal management system provides good cooling control of the temperature of the batteries under high and continuous charge and discharge cycles at 7.5C.

  18. Pool Boiling of Hydrocarbon Mixtures on Water

    Energy Technology Data Exchange (ETDEWEB)

    Boee, R.

    1996-09-01

    In maritime transport of liquefied natural gas (LNG) there is a risk of spilling cryogenic liquid onto water. The present doctoral thesis discusses transient boiling experiments in which liquid hydrocarbons were poured onto water and left to boil off. Composition changes during boiling are believed to be connected with the initiation of rapid phase transition in LNG spilled on water. 64 experimental runs were carried out, 14 using pure liquid methane, 36 using methane-ethane, and 14 using methane-propane binary mixtures of different composition. The water surface was open to the atmosphere and covered an area of 200 cm{sup 2} at 25 - 40{sup o}C. The heat flux was obtained by monitoring the change of mass vs time. The void fraction in the boiling layer was measured with a gamma densitometer, and a method for adapting this measurement concept to the case of a boiling cryogenic liquid mixture is suggested. Significant differences in the boil-off characteristics between pure methane and binary mixtures revealed by previous studies are confirmed. Pure methane is in film boiling, whereas the mixtures appear to enter the transitional boiling regime with only small amounts of the second component added. The results indicate that the common assumption that LNG will be in film boiling on water because of the high temperature difference, may be questioned. Comparison with previous work shows that at this small scale the results are influenced by the experimental apparatus and procedures. 66 refs., 76 figs., 28 tabs.

  19. Flow boiling heat transfer and pressure drop characteristics of R134a, R1234yf and R1234ze in a plate heat exchanger for organic Rankine cycle units

    DEFF Research Database (Denmark)

    Zhang, Ji; Desideri, Adriano; Kærn, Martin Ryhl

    2017-01-01

    . This paper is aimed at obtaining flow boiling heat transfer and pressure drop characteristics in a plate heat exchanger under the working conditions prevailing in the evaporator of organic Rankine cycle units. Two hydrofluoroolefins R1234yf and R1234ze, and one hydrofluorocarbon R134a, were selected...

  20. Accident source terms for boiling water reactors with high burnup cores.

    Energy Technology Data Exchange (ETDEWEB)

    Gauntt, Randall O.; Powers, Dana Auburn; Leonard, Mark Thomas

    2007-11-01

    The primary objective of this report is to provide the technical basis for development of recommendations for updates to the NUREG-1465 Source Term for BWRs that will extend its applicability to accidents involving high burnup (HBU) cores. However, a secondary objective is to re-examine the fundamental characteristics of the prescription for fission product release to containment described by NUREG-1465. This secondary objective is motivated by an interest to understand the extent to which research into the release and behaviors of radionuclides under accident conditions has altered best-estimate calculations of the integral response of BWRs to severe core damage sequences and the resulting radiological source terms to containment. This report, therefore, documents specific results of fission product source term analyses that will form the basis for the HBU supplement to NUREG-1465. However, commentary is also provided on observed differences between the composite results of the source term calculations performed here and those reflected NUREG-1465 itself.

  1. Enhanced mobility of poly(3-hexylthiophene) transistors by spin-coating from high-boiling-point solvents

    DEFF Research Database (Denmark)

    Chang, J.F.; Sun, B.Q.; Breiby, Dag Werner

    2004-01-01

    Chloroform is a general solvent for poly(3-hexylthiophene) (P3HT) active layers in field-effect transistors. However, its low boiling point and rapid evaporation limit the time for crystallization during the spin-coating process, and field-effect mobilities achieved for P3HT films spin-coated from...

  2. Experimental boiling heat transfer coefficients in the high temperature generator of a double effect absorption machine for the lithium bromide/water mixture

    Energy Technology Data Exchange (ETDEWEB)

    Marcos, J.D. [Escuela Tecnica Superior Ingenieria Industrial, UNED, c/Juan del Rosal 12, 28040 Madrid (Spain); Izquierdo, M. [Instituto de Ciencias de la Construccion Eduardo Torroja (CSIC), c/Serrano Galvache 4, 28033 Madrid (Spain); Escuela Politecnica Superior, Universidad Carlos III de Madrid, Avenida de la Universidad 30, 28911 Leganes, Madrid (Spain); Lizarte, R. [Escuela Politecnica Superior, Universidad Carlos III de Madrid, Avenida de la Universidad 30, 28911 Leganes, Madrid (Spain); Palacios, E. [Escuela Universitaria Ingenieria Tecnica Industrial, Universidad Politecnica de Madrid, C/ Ronda de Valencia 3, 28012 Madrid (Spain); Infante Ferreira, C.A. [Delft University of Technology, Engineering Thermodynamics, Leeghwaterstraat 44, 2628 CA Delft (Netherlands)

    2009-06-15

    The aim of this work is to determine the boiling heat transfer coefficients in the high temperature desorber (HTD) of an air-cooled double effect lithium bromide/water absorption prototype. The HTD is a plate heat exchanger (PHE) with thermal oil on one side, and a lithium bromide solution on the other side. Several experiments were performed with this PHE while the prototype was working with an outdoor dry bulb temperature around 42 C and condensation temperature around 55 C. The registered data allowed to calculate the global heat transfer coefficient and the heat transfer coefficient for the LiBr/water mixture in forced convective boiling. The pressure drop produced by the boiling of the refrigerant has been calculated as well. It has been verified that the largest part of the heat supplied in the generator is required for desorbing the refrigerant (except for the maximum solution mass flow), while the sensible heat varies from 10% to 50% of the total heat supplied. (author)

  3. Multi-parametric monitoring and assessment of high-intensity focused ultrasound (HIFU) boiling by harmonic motion imaging for focused ultrasound (HMIFU): an ex vivo feasibility study.

    Science.gov (United States)

    Hou, Gary Y; Marquet, Fabrice; Wang, Shutao; Konofagou, Elisa E

    2014-03-07

    Harmonic motion imaging for focused ultrasound (HMIFU) is a recently developed high-intensity focused ultrasound (HIFU) treatment monitoring method with feasibilities demonstrated in vitro and in vivo. Here, a multi-parametric study is performed to investigate both elastic and acoustics-independent viscoelastic tissue changes using the Harmonic Motion Imaging (HMI) displacement, axial compressive strain and change in relative phase shift during high energy HIFU treatment with tissue boiling. Forty three (n = 43) thermal lesions were formed in ex vivo canine liver specimens (n = 28). Two-dimensional (2D) transverse HMI displacement maps were also obtained before and after lesion formation. The same method was repeated in 10 s, 20 s and 30 s HIFU durations at three different acoustic powers of 8, 10, and 11 W, which were selected and verified as treatment parameters capable of inducing boiling using both thermocouple and passive cavitation detection (PCD) measurements. Although a steady decrease in the displacement, compressive strain, and relative change in the focal phase shift (Δϕ) were obtained in numerous cases, indicating an overall increase in relative stiffness, the study outcomes also showed that during boiling, a reverse lesion-to-background displacement contrast was detected, indicating potential change in tissue absorption, geometrical change and/or, mechanical gelatification or pulverization. Following treatment, corresponding 2D HMI displacement images of the thermal lesions also mapped consistent discrepancy in the lesion-to-background displacement contrast. Despite the expectedly chaotic changes in acoustic properties with boiling, the relative change in phase shift showed a consistent decrease, indicating its robustness to monitor biomechanical properties independent of the acoustic property changes throughout the HIFU treatment. In addition, the 2D HMI displacement images confirmed and indicated the increase in the thermal lesion size with

  4. Multi-parametric monitoring and assessment of High Intensity Focused Ultrasound (HIFU) boiling by Harmonic Motion Imaging for Focused Ultrasound (HMIFU): An ex vivo feasibility study

    Science.gov (United States)

    Hou, Gary Y.; Marquet, Fabrice; Wang, Shutao; Konofagou, Elisa E.

    2014-01-01

    Harmonic Motion Imaging for Focused Ultrasound (HMIFU) is a recently developed high-intensity focused ultrasound (HIFU) treatment monitoring method with feasibilities demonstrated in vitro and in vivo. Here, a multi-parametric study is performed to investigate both elastic and acoustics-independent viscoelastic tissue changes using the Harmonic Motion Imaging (HMI) displacement, axial compressive strain and change in relative phase-shift during high energy HIFU treatment with tissue boiling. Forty three (n=43) thermal lesions were formed in ex vivo canine liver specimens (n=28). Two dimensional (2D) transverse HMI displacement maps were also obtained before and after lesion formation. The same method was repeated in 10-s, 20-s and 30-s HIFU durations at three different acoustic powers of 8, 10, and 11W, which were selected and verified as treatment parameters capable of inducing boiling using both thermocouple and Passive Cavitation Detection (PCD) measurements. Although a steady decrease in the displacement, compressive strain, and relative change in the focal phase shift (Δφ) were obtained in numerous cases, indicating an overall increase in relative stiffness, the study outcomes also showed that during boiling, a reverse lesion-to-background displacement contrast was detected, indicating potential change in tissue absorption, geometrical change and/or, mechanical gelatification or pulverization. Following treatment, corresponding 2D HMI displacement images of the thermal lesions also mapped consistent discrepancy in the lesion-to-background displacement contrast. Despite unpredictable changes in acoustic properties with boiling, the relative change in phase shift showed a consistent decrease, indicating its robustness to monitor biomechanical properties independent of the acoustic property change throughout the HIFU treatment. In addition, the 2D HMI displacement images confirmed and indicated the increase in the thermal lesion size with treatment duration

  5. 估算有机物正常沸点的基团贡献法的研究进展%Research Progress of Group - contribution Methods for Estimating Normal Boiling Point of Organic Compounds

    Institute of Scientific and Technical Information of China (English)

    王小艳; 司继林

    2012-01-01

    Normal boiling points are one of the most important properties for organic compounds. Although there are many experimental values of the normal boiling point of organic compounds in the literature, but there are a few normal boiling point of the material cannot be obtained by experiment. We can obtain the normal boiling points by establishing the mathematical model, the group contribution method is the most important research methods to obtain the normal boiling point. A variety of group - contribution methods for estimating normal boiling point of organic compounds have been summarized. It has discussed the principles, advantages and disadvantages, application ranges of Joback method, C - G method, Xu - Wen method, position group contribution method, elements and bonds. The difference of these methods and the development trend of the methods for estimating normal boiling point of organic compounds was discussed.%有机物的正常沸点是重要的物性数据之一。尽管文献中有很多化合物正常沸点的实验值,但一些物质的正常沸点不能由实验获得,可以通过建立数学模型来估算缺少的有机物正常沸点,其中基团贡献法是人们获得正常沸点的最重要研究方法。本文对估算有机物正常沸点的基团贡献法进行了综述。主要介绍了Joback法、C—G法、许文法、定位分布贡献法、元素和化学键法等方法的原理、优缺点及应用范围;并对这些方法进行简单的比较;最后指出了有机物正常沸点的基团贡献法的发展趋势。

  6. Evaporation, Boiling and Bubbles

    Science.gov (United States)

    Goodwin, Alan

    2012-01-01

    Evaporation and boiling are both terms applied to the change of a liquid to the vapour/gaseous state. This article argues that it is the formation of bubbles of vapour within the liquid that most clearly differentiates boiling from evaporation although only a minority of chemistry textbooks seems to mention bubble formation in this context. The…

  7. Evaporation, Boiling and Bubbles

    Science.gov (United States)

    Goodwin, Alan

    2012-01-01

    Evaporation and boiling are both terms applied to the change of a liquid to the vapour/gaseous state. This article argues that it is the formation of bubbles of vapour within the liquid that most clearly differentiates boiling from evaporation although only a minority of chemistry textbooks seems to mention bubble formation in this context. The…

  8. 脂肪族含氧有机物沸点的定量构效关系%Quantitative structure-property relationship of normal boiling point of aliphatic oxygen-containing organic compounds

    Institute of Scientific and Technical Information of China (English)

    刘万强; 曹晨忠

    2012-01-01

    The descriptors of polarizability effect index (PEI),the number of effective carbon (Nc,e(f)> the differences in PEI and Nc,eff between the branching chain and straight chain isomers,SPEI and δ Nc,eff,are derived from molecular structure. The quantitative structure-property relationships (QSPRs) between these descriptors and boiling points of 520 aliphatic alcohols,ethers,aldehydes,ketones,acids,and esters were obtained separately. The QSPRs between these descriptors and boiling points were developed for 520 aliphatic oxygen-containing organic compounds by best subsets regression method. For the training set,the correlation coefficient R2 is 0. 9946 and the standard deviation GO is 6. 70 K. For the test set,R2 is 0. 9857 and s is 6. 10 K. The average relative error is 1. 19%. According to the regression equation,the influences of the number of effective carbon of alkyl,the role of functional groups and their interaction on the boiling point were analyzed. These results showed a good correlation between the boiling points of organic compounds and these descriptors derived from PEI for aliphatic alcohols,ethers,aldehydes,ketones,acids,and esters.

  9. A high-sensitivity magnetocardiography system with a divided gradiometer array inside a low boil-off Dewar

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Y H; Yu, K K; Kim, J M; Kwon, H; Kim, K, E-mail: yhlee@kriss.re.k [Korea Research Institute of Standards and Science, 1 Doryong, Yuseong, Daejeon 305-600 (Korea, Republic of)

    2009-11-15

    We fabricated a low-noise 64-channel first-order axial gradiometer system for measuring magnetocardiography (MCG) signals. The key technical features of the system are the compact structure of the gradiometer, division of the sensor array plate, direct mounting of the sensor plates into the Dewar bottom, reduced neck diameter of the liquid He Dewar, and compact readout electronics. To make the refill interval of liquid He longer, the distance between the compensation coil of the gradiometer and the input coil pads of the superconducting quantum interference device (SQUID) was reduced to 20 mm. By using direct ultrasonic bonding of Nb wires between the pickup coil wires and input coil pads, the superconductive connection structure became simple. The baseline of the first-order gradiometer is 70 mm, a little longer than for typical conventional axial gradiometers, to provide a larger signal amplitude for deep sources. The 64-channel gradiometer array consists of four blocks, and each block is fixed separately onto the bottom of the Dewar. The neck diameter of the He Dewar (192 mm) is smaller than the bottom diameter (280 mm) in which the gradiometers are distributed. The average boil-off rate of the Dewar is 3 l per day when the 64-channel system is in operation every day. Double relaxation oscillation SQUIDs (DROSs) having large flux-to-voltage transfer coefficients were used to operate SQUIDs via compact electronics. The magnetically shielded room (MSR) has a wall thickness of 80 mm, and consists of two layers of permalloy and one layer of aluminum. When the 64-channel system was installed inside the MSR, the field noise level of the system was about 3.5 fT{sub rms} Hz{sup -1/2} at 100 Hz. MCG measurements with high signal quality were done successfully using the developed system. In addition to the parameter analysis method, we developed software for the three-dimensional imaging of the myocardial current on a realistic image of the heart based on the anatomical

  10. Numerical solution of one-dimensional transient, two-phase flows with temporal fully implicit high order schemes: Subcooled boiling in pipes

    Energy Technology Data Exchange (ETDEWEB)

    López, R., E-mail: ralope1@ing.uc3m.es; Lecuona, A., E-mail: lecuona@ing.uc3m.es; Nogueira, J., E-mail: goriba@ing.uc3m.es; Vereda, C., E-mail: cvereda@ing.uc3m.es

    2017-03-15

    Highlights: • A two-phase flows numerical algorithm with high order temporal schemes is proposed. • Transient solutions route depends on the temporal high order scheme employed. • ESDIRK scheme for two-phase flows events exhibits high computational performance. • Computational implementation of the ESDIRK scheme can be done in a very easy manner. - Abstract: An extension for 1-D transient two-phase flows of the SIMPLE-ESDIRK method, initially developed for incompressible viscous flows by Ijaz is presented. This extension is motivated by the high temporal order of accuracy demanded to cope with fast phase change events. This methodology is suitable for boiling heat exchangers, solar thermal receivers, etc. The methodology of the solution consist in a finite volume staggered grid discretization of the governing equations in which the transient terms are treated with the explicit first stage singly diagonally implicit Runge-Kutta (ESDIRK) method. It is suitable for stiff differential equations, present in instant boiling or condensation processes. It is combined with the semi-implicit pressure linked equations algorithm (SIMPLE) for the calculation of the pressure field. The case of study consists of the numerical reproduction of the Bartolomei upward boiling pipe flow experiment. The steady-state validation of the numerical algorithm is made against these experimental results and well known numerical results for that experiment. In addition, a detailed study reveals the benefits over the first order Euler Backward method when applying 3rd and 4th order schemes, making emphasis in the behaviour when the system is subjected to periodic square wave wall heat function disturbances, concluding that the use of the ESDIRK method in two-phase calculations presents remarkable accuracy and computational advantages.

  11. Aspects of subcooled boiling

    Energy Technology Data Exchange (ETDEWEB)

    Bankoff, S.G. [Northwestern Univ., Evanston, IL (United States)

    1997-12-31

    Subcooled boiling boiling refers to boiling from a solid surface where the bulk liquid temperature is below the saturation temperature (subcooled). Two classes are considered: (1) nucleate boiling, where, for large subcoolings, individual bubbles grow and collapse while remaining attached to the solid wall, and (2) film boiling, where a continuous vapor film separates the solid from the bulk liquid. One mechanism by which subcooled nucleate boiling results in very large surface heat transfer coefficient is thought to be latent heat transport within the bubble, resulting from simultaneous evaporation from a thin residual liquid layer at the bubble base, and condensation at the polar bubble cap. Another is the increased liquid microconvection around the oscillating bubble. Two related problems have been attacked. One is the rupture of a thin liquid film subject to attractive and repulsive dispersion forces, leading to the formation of mesoscopic drops, which then coalesce and evaporate. Another is the liquid motion in the vicinity of an oscillating contact line, where the bubble wall is idealized as a wedge of constant angle sliding on the solid wall. The subcooled film boiling problem has been attacked by deriving a general long-range nonlinear evolution equation for the local thickness of the vapor layer. Linear and weakly-nonlinear stability results have been obtained. A number of other related problems have been attacked.

  12. The Relationship Between the Color Characteristics of the RGB Colorimetric System and the Physicochemical Properties of Petroleums and high Boiling Hydrocarbon Distillates

    Science.gov (United States)

    Dolomatov, M. Yu.; Yarmuhametova, G. U.

    2016-09-01

    An interrelation was established between physicochemical properties of oils and high boiling hydrocarbon distillates and their solutions' color characteristics defi ned in the RGB colorimetric system using a standard radiation source CIE D65. It was shown that by using color characteristics of solutions of the specifi ed objects, it was possible to determine their relative density, molecular mass, activation energy of viscous fl ow, and the coking value. Research results were confi rmed by statistical data processing using the methods of multivariate regression and correlation analysis.

  13. 有机硅高沸物制备硅油脱模剂的研究进展%Progress on Silicone Oil Mold-release Agent by Silicone High-boiling Compound

    Institute of Scientific and Technical Information of China (English)

    王宇光; 王晓英; 刘颖

    2013-01-01

    简述了有机硅高沸物制备硅油脱模剂的原理及流程,介绍了近年来有机硅高沸物制备硅油脱模剂的研究进展,并对国内有机硅高沸物制备硅油脱模剂的发展方向提出了建议.%This paper described the principles and processes of silicone oil mold-release agent preparation by high-boiling point organic silicon compounds, and introduced research reviews on the preparation of silicone oil mold-release agent, and some suggestions on development direction of silicone oil mold-release agent were proposed.

  14. Odd-Boiled Eggs

    Science.gov (United States)

    Kaminsky, Kenneth; Scheman, Naomi

    2010-01-01

    At a Shabbat lunch in Madrid not long ago, the conversation turned to the question of boiling eggs. One of the guests mentioned that a Dutch rabbi he knew had heard that in order to make it more likely that boiled eggs be kosher, you should add an egg to the pot if the number you began with was even. According to the laws of Kashruth, Jews may not…

  15. Improving efficiency and color purity of poly(9,9-dioctylfluorene) through addition of a high boiling-point solvent of 1-chloronaphthalene

    Science.gov (United States)

    Liang, Junfei; Yu, Lei; Zhao, Sen; Ying, Lei; Liu, Feng; Yang, Wei; Peng, Junbiao; Cao, Yong

    2016-07-01

    In this work, the β-phase of poly(9,9-dioctylfluorene) (PFO) was used as a probe to study the effects of the addition of a high boiling-point solvent of 1-chloronaphthalene on the nanostructures and electroluminescence of PFO films. Both absorption and photoluminescence spectra showed that the content of the β-phase in PFO film was obviously enhanced as a result of the addition of a small amount of 1-chloronaphthalene into the processing solvent of p-xylenes. Apparently rougher morphology associated with the effectively enhanced ordering of polymer chains across the entire film was observed for films processed from p-xylene solutions consisting of a certain amount of 1-chloronaphthalene, as revealed by atomic force microscopy and grazing incidence x-ray diffraction measurements. In addition to the effects on the nanostructures of films, of particular interest is that the performance and color purity of polymer light-emitting devices can be noticeably enhanced upon the addition of 1-chloronaphthalene. These observations highlight the importance of controlling the nanostructures of the emissive layer, and demonstrate that the addition of a low volume ratio of high boiling-point additive can be a promising strategy to attain high-performance polymer light-emitting diodes.

  16. Nucleate boiling heat transfer

    Energy Technology Data Exchange (ETDEWEB)

    Saiz Jabardo, J.M. [Universidade da Coruna (Spain). Escola Politecnica Superior], e-mail: mjabardo@cdf.udc.es

    2009-07-01

    Nucleate boiling heat transfer has been intensely studied during the last 70 years. However boiling remains a science to be understood and equated. In other words, using the definition given by Boulding, it is an 'insecure science'. It would be pretentious of the part of the author to explore all the nuances that the title of the paper suggests in a single conference paper. Instead the paper will focus on one interesting aspect such as the effect of the surface microstructure on nucleate boiling heat transfer. A summary of a chronological literature survey is done followed by an analysis of the results of an experimental investigation of boiling on tubes of different materials and surface roughness. The effect of the surface roughness is performed through data from the boiling of refrigerants R-134a and R-123, medium and low pressure refrigerants, respectively. In order to investigate the extent to which the surface roughness affects boiling heat transfer, very rough surfaces (4.6 {mu}m and 10.5 {mu}m ) have been tested. Though most of the data confirm previous literature trends, the very rough surfaces present a peculiar behaviour with respect to that of the smoother surfaces (Ra<3.0 {mu}m). (author)

  17. Designing High-Trust Organizations

    DEFF Research Database (Denmark)

    Jagd, Søren

    the existing management and research literature on building high-trust organizations. Then I explore Alan Fox’s (1974) analysis of low-trust vs. high-trust dynamics which, I argue, may serve as a theoretically stronger basis for understanding the issues management have to consider when designing hightrust......The specific problem considered in this paper is what are the key issues to consider for managers involved in designing high-trust organizations, a design problem still not properly explored. This paper intends to take the first step in filling this lacuna. In the paper, I first present...... organizations...

  18. Becoming a high reliability organization.

    Science.gov (United States)

    Christianson, Marlys K; Sutcliffe, Kathleen M; Miller, Melissa A; Iwashyna, Theodore J

    2011-01-01

    Aircraft carriers, electrical power grids, and wildland firefighting, though seemingly different, are exemplars of high reliability organizations (HROs)--organizations that have the potential for catastrophic failure yet engage in nearly error-free performance. HROs commit to safety at the highest level and adopt a special approach to its pursuit. High reliability organizing has been studied and discussed for some time in other industries and is receiving increasing attention in health care, particularly in high-risk settings like the intensive care unit (ICU). The essence of high reliability organizing is a set of principles that enable organizations to focus attention on emergent problems and to deploy the right set of resources to address those problems. HROs behave in ways that sometimes seem counterintuitive--they do not try to hide failures but rather celebrate them as windows into the health of the system, they seek out problems, they avoid focusing on just one aspect of work and are able to see how all the parts of work fit together, they expect unexpected events and develop the capability to manage them, and they defer decision making to local frontline experts who are empowered to solve problems. Given the complexity of patient care in the ICU, the potential for medical error, and the particular sensitivity of critically ill patients to harm, high reliability organizing principles hold promise for improving ICU patient care.

  19. Increasing Boiling Heat Transfer using Low Conductivity Materials.

    Science.gov (United States)

    Rahman, Md Mahamudur; Pollack, Jordan; McCarthy, Matthew

    2015-08-18

    We report the counterintuitive mechanism of increasing boiling heat transfer by incorporating low-conductivity materials at the interface between the surface and fluid. By embedding an array of non-conductive lines into a high-conductivity substrate, in-plane variations in the local surface temperature are created. During boiling the surface temperature varies spatially across the substrate, alternating between high and low values, and promotes the organization of distinct liquid and vapor flows. By systematically tuning the peak-to-peak wavelength of this spatial temperature variation, a resonance-like effect is seen at a value equal to the capillary length of the fluid. Replacing ~18% of the surface with a non-conductive epoxy results in a greater than 5x increase in heat transfer rate at a given superheat temperature. This drastic and counterintuitive increase is shown to be due to optimized bubble dynamics, where ordered pathways allow for efficient removal of vapor and the return of replenishing liquid. The use of engineered thermal gradients represents a potentially disruptive approach to create high-efficiency and high-heat-flux boiling surfaces which are naturally insensitive to fouling and degradation as compared to other approaches.

  20. Numerical Investigation of Boiling

    Science.gov (United States)

    Sagan, Michael; Tanguy, Sebastien; Colin, Catherine

    2012-11-01

    In this work, boiling is numerically investigated, using two phase flow direct numerical simulation based on a level set / Ghost Fluid method. Nucleate boiling implies both thermal issue and multiphase dynamics issues at different scales and at different stages of bubble growth. As a result, the different phenomena are investigated separately, considering their nature and the scale at which they occur. First, boiling of a static bubble immersed in an overheated liquid is analysed. Numerical simulations have been performed at different Jakob numbers in the case of strong density discontinuity through the interface. The results show a good agreement on bubble radius evolution between the theoretical evolution and numerical simulation. After the validation of the code for the Scriven test case, interaction of a bubble with a wall is studied. A numerical method taking into account contact angle is evaluated by comparing simulations of the spreading of a liquid droplet impacting on a plate, with experimental data. Then the heat transfer near the contact line is investigated, and simulations of nucleate boiling are performed considering different contact angles values. Finally, the relevance of including a model to take into account the evaporation of the micro layer is discussed.

  1. QSPR Calculation of Normal Boiling Points of Organic Molecules Based on the Use of Correlation Weighting of Atomic Orbitals with Extended Connectivity of Zero- and First-Order Graphs of Atomic Orbitals

    Directory of Open Access Journals (Sweden)

    Eduardo A. Castro

    2004-12-01

    Full Text Available We report the results of a calculation of the normal boiling points of a representative set of 200 organic molecules through the application of QSPR theory. For this purpose we have used a particular set of flexible molecular descriptors, the so called Correlation Weighting of Atomic Orbitals with Extended Connectivity of Zero- and First-Order Graphs of Atomic Orbitals. Although in general the results show suitable behavior to predict this physical chemistry property, the existence of some deviant behaviors points to a need to complement this index with some other sort of molecular descriptors. Some possible extensions of this study are discussed.

  2. Cryogenic Boil-Off Reduction System

    Science.gov (United States)

    Plachta, David W.; Guzik, Monica C.

    2014-03-01

    A computational model of the cryogenic boil-off reduction system being developed by NASA as part of the Cryogenic Propellant Storage and Transfer technology maturation project has been applied to a range of propellant storage tanks sizes for high-performing in-space cryogenic propulsion applications. This effort focuses on the scaling of multi-layer insulation (MLI), cryocoolers, broad area cooling shields, radiators, solar arrays, and tanks for liquid hydrogen propellant storage tanks ranging from 2 to 10 m in diameter. Component scaling equations were incorporated into the Cryogenic Analysis Tool, a spreadsheet-based tool used to perform system-level parametric studies. The primary addition to the evolution of this updated tool is the integration of a scaling method for reverse turbo-Brayton cycle cryocoolers, as well as the development and inclusion of Self-Supporting Multi-Layer Insulation. Mass, power, and sizing relationships are traded parametrically to establish the appropriate loiter period beyond which this boil-off reduction system application reduces mass. The projected benefit compares passive thermal control to active thermal control, where active thermal control is evaluated for reduced boil-off with a 90 K shield, zero boil-off with a single heat interception stage at the tank wall, and zero boil-off with a second interception stage at a 90 K shield. Parametric studies show a benefit over passive storage at loiter durations under one month, in addition to showing a benefit for two-stage zero boil-off in terms of reducing power and mass as compared to single stage zero boil-off. Furthermore, active cooling reduces the effect of varied multi-layer insulation performance, which, historically, has been shown to be significant.

  3. The law of stable equilibrium and the entropy-based boiling curve for flow boiling

    Energy Technology Data Exchange (ETDEWEB)

    Collado, F.J. [Universidad de Zaragoza (Spain). Dpto. Ingenieria Mecanica Motores Termicos

    2005-05-01

    Convective flow boiling in sub-cooled fluids is recognized as one of the few means of accommodating very high heat fluxes. There are many available correlations for predicting the inner wall temperature of the heated duct in the several regimes of the empirical Nukiyama boiling curve, although unfortunately there is no physical fundamentals of such curve. Recently, the author has shown that the classical entropy balance could contain key information about boiling heat transfer. So, it was found that the average thermal gap in the heated channel (the inner wall temperature minus the average temperature of the coolant fluid) was strongly correlated with the efficiency of a theoretical reversible engine placed in this thermal gap. From this new correlation, a new boiling curve plotting the wall temperature versus the average fluid temperature was derived and successfully checked against low- and high-pressure water data. This curve suggested a new and simple definition of the critical heat flux (CHF) namely, the value of the coolant average temperature at the maximum. In this work, after briefly reviewing the entropy balance of a non-equilibrium boiling flow and its relationship with the thermodynamic average temperature and the law of stable equilibrium (LSE), the possibilities of the new approach for the design of flow boiling cooling systems are highlighted. Finally, the strong correlation found between the reversible engine efficiency and the thermal driving force is verified again, now with high-pressure refrigerant 22 (R-22) data. (author)

  4. 定位分布贡献方法估算有机物正常沸点%Position group contribution method for predicting the normal boiling point of organic compounds

    Institute of Scientific and Technical Information of China (English)

    王强; 马沛生; 王昶; 夏淑倩

    2009-01-01

    A new position group contribution model iS proposed for the estimation of normal boiling data of organic compounds involving a carbon chain from C2 to C18. The characteristic of this method iS the use of position distribution function.It could distinguish most of isomers that include cis-or trans-structure from organic compounds.Contributions for hydrocarbons and hydrocarbon derivatives containing oxygen,nitrogen,chlorine,bromine and sulfur,are given.Compared with the predictions,results made use of the most common existing group contribution methods,the overall average absolute difference of boiling point predictions of 417 organic compounds is 4.2 K:and the average absolute percent derivation is 1.0%,which iS compared with 1 2-3 K and 3.2%with the method of Joback.12.1 K and 3.1%with the method of Constantinou-Gani.This new position contribution groups mcthod is not only much more accurate but also has the advantages of simplicity and stability.

  5. Thermodynamics of Flow Boiling Heat Transfer

    Science.gov (United States)

    Collado, F. J.

    2003-05-01

    Convective boiling in sub-cooled water flowing through a heated channel is essential in many engineering applications where high heat flux needs to be accommodated. It has been customary to represent the heat transfer by the boiling curve, which shows the heat flux versus the wall-minus-saturation temperature difference. However it is a rather complicated problem, and recent revisions of two-phase flow and heat transfer note that calculated values of boiling heat transfer coefficients present many uncertainties. Quite recently, the author has shown that the average thermal gap in the heated channel (the wall temperature minus the average temperature of the coolant) was tightly connected with the thermodynamic efficiency of a theoretical reversible engine placed in this thermal gap. In this work, whereas this correlation is checked again with data taken by General Electric (task III) for water at high pressure, a possible connection between this wall efficiency and the reversible-work theorem is explored.

  6. Geysering in boiling channels

    Energy Technology Data Exchange (ETDEWEB)

    Aritomi, Masanori; Takemoto, Takatoshi [Tokyo Institute of Technology, Tokyo (Japan); Chiang, Jing-Hsien [Japan NUS Corp. Ltd., Toyko (Japan)] [and others

    1995-09-01

    A concept of natural circulation BWRs such as the SBWR has been proposed and seems to be promising in that the primary cooling system can be simplified. The authors have been investigating thermo-hydraulic instabilities which may appear during the start-up in natural circulation BWRs. In our previous works, geysering was investigated in parallel boiling channels for both natural and forced circulations, and its driving mechanism and the effect of system pressure on geysering occurrence were made clear. In this paper, geysering is investigated in a vertical column and a U-shaped vertical column heated in the lower parts. It is clarified from the results that the occurrence mechanism of geysering and the dependence of system pressure on geysering occurrence coincide between parallel boiling channels in circulation systems and vertical columns in non-circulation systems.

  7. Oscillate boiling from microheaters

    Science.gov (United States)

    Li, Fenfang; Gonzalez-Avila, S. Roberto; Nguyen, Dang Minh; Ohl, Claus-Dieter

    2017-01-01

    We report about an intriguing boiling regime occurring for small heaters embedded on the boundary in subcooled water. The microheater is realized by focusing a continuous wave laser beam to about 10 μ m in diameter onto a 165-nm-thick layer of gold, which is submerged in water. After an initial vaporous explosion a single bubble oscillates continuously and repeatedly at several 100 kHz albeit with constant laser power input. The microbubble's oscillations are accompanied with bubble pinch-off, leading to a stream of gaseous bubbles in the subcooled water. The self-driven bubble oscillation is explained with a thermally kicked oscillator caused by surface attachment and by the nonspherical collapses. Additionally, Marangoni stresses induce a recirculating streaming flow which transports cold liquid towards the microheater, reducing diffusion of heat along the substrate and therefore stabilizing the phenomenon to many million cycles. We speculate that this oscillate boiling regime may overcome the heat transfer thresholds observed during the nucleate boiling crisis and offers a new pathway for heat transfer under microgravity conditions.

  8. Boiling incipience and convective boiling of neon and nitrogen

    Science.gov (United States)

    Papell, S. S.; Hendricks, R. C.

    1977-01-01

    Forced convection and subcooled boiling heat transfer data for liquid nitrogen and liquid neon were obtained in support of a design study for a 30 tesla cryomagnet cooled by forced convection of liquid neon. This design precludes nucleate boiling in the flow channels as they are too small to handle vapor flow. Consequently, it was necessary to determine boiling incipience under the operating conditions of the magnet system. The cryogen data obtained over a range of system pressures, fluid flow rates, and applied heat fluxes were used to develop correlations for predicting boiling incipience and convective boiling heat transfer coefficients in uniformly heated flow channels. The accuracy of the correlating equations was then evaluated. A technique was also developed to calculate the position of boiling incipience in a uniformly heated flow channel. Comparisons made with the experimental data showed a prediction accuracy of plus or minus 15 percent

  9. Influence of Pressure on Stable Film Boiling of Subcooled Liquid

    Science.gov (United States)

    Zabirov, A. R.; Yagov, V. V.; Kaban'kov, O. N.; Leksin, M. A.; Kanin, P. K.

    2016-11-01

    Film boiling of subcooled liquids is an integral part of the hardening process. Understanding of the mechanisms underlying film boiling is important for modeling processes in atomic power engineering and cryogenic technology. Stationary processes of film boiling of subcooled liquids under conditions of their free motion near cylindrical heaters, just as subcooled liquid turbulent flow past high-temperature surfaces, represent quite a different type of process. In cooling metal spheres heated to a high temperature by a subcooled water, a special regime of film boiling is observed (microbubble boiling) distinguished by high intensity of heat transfer. Such a regime has not been revealed up to now for nonaqueous liquids. The paper presents new experimental data on heat transfer regimes in cooling nickel spheres in subcooled isopropanol and perfluorohexane at pressures of up to 1 MPa. It has been established that stable film boiling is the main regime of heat transfer that accounts for the larger part of the total time of cooling. The regimes of highly intensive film boiling heat transfer were not observed in the entire range of operational parameters even in the case of extreme subcoolings of liquid below their saturation temperature (to 170 K). The intensity of heat transfer in stable film boiling increases noticeably with subcooling of a chilling liquid.

  10. Low-Flow Film Boiling Heat Transfer on Vertical Surfaces

    DEFF Research Database (Denmark)

    Munthe Andersen, J. G.; Dix, G. E.; Leonard, J. E.

    1976-01-01

    The phenomenon of film boiling heat transfer for high wall temperatures has been investigated. Based on the assumption of laminar flow for the film, the continuity, momentum, and energy equations for the vapor film are solved and a Bromley-type analytical expression for the heat transfer...... length, an average film boiling heat transfer coefficient is obtained....

  11. Direct Numerical Simulation and Visualization of Subcooled Pool Boiling

    Directory of Open Access Journals (Sweden)

    Tomoaki Kunugi

    2014-01-01

    Full Text Available A direct numerical simulation of the boiling phenomena is one of the promising approaches in order to clarify their heat transfer characteristics and discuss the mechanism. During these decades, many DNS procedures have been developed according to the recent high performance computers and computational technologies. In this paper, the state of the art of direct numerical simulation of the pool boiling phenomena during mostly two decades is briefly summarized at first, and then the nonempirical boiling and condensation model proposed by the authors is introduced into the MARS (MultiInterface Advection and Reconstruction Solver developed by the authors. On the other hand, in order to clarify the boiling bubble behaviors under the subcooled conditions, the subcooled pool boiling experiments are also performed by using a high speed and high spatial resolution camera with a highly magnified telescope. Resulting from the numerical simulations of the subcooled pool boiling phenomena, the numerical results obtained by the MARS are validated by being compared to the experimental ones and the existing analytical solutions. The numerical results regarding the time evolution of the boiling bubble departure process under the subcooled conditions show a very good agreement with the experimental results. In conclusion, it can be said that the proposed nonempirical boiling and condensation model combined with the MARS has been validated.

  12. The entropy balance for boiling flow

    Energy Technology Data Exchange (ETDEWEB)

    Collado, Francisco-Javier E-mail: fjk@posta.unizar.es

    2001-10-01

    Subcooled forced convection boiling of water is recognized as one of the best means of accommodating the very high heat fluxes that plasma facing components of fusion reactors have to withstand. The boiling curve, giving the wall temperature in function of the applied flux and flow conditions, is essential for the design of such cooling configurations. In this paper, a new entropy balance for subcooled boiling flow, which allows the wall temperature to be obtained, is presented and successfully compared with experimental data from the Joint US-EURATOM R and D Program. The derivation of this entropy balance is based on a new strict application of the Reynolds theorem to multiphase flows recently proposed by the author.

  13. Gravimetric analysis of the solubility of methane in high boiling hydrocarbons and petroleum products; Gravimetrische Bestimmung der Loeslichkeit von Methan in hoeher siedenden Kohlenwasserstoffen und Erdoelprodukten

    Energy Technology Data Exchange (ETDEWEB)

    Laux, H.; Rahimian, I. [Institut fuer Erdoel- und Erdgasforschung, Clausthal-Zellerfeld (Germany)

    2001-05-01

    The solubility of methane has a great influence on the colloid stability of crude oils at the conditions of production. Adequate data are needed for the modelling of the beginning of asphaltene precipitation as the result of the destabilization. Because such data are limited in the literature a magnetic suspension balance was used. By means of the magnetic suspension balance the solubility of gases in high boiling products can be determined by the weight difference resulting from the steped pressure reduction. The solubility of methane was investigated in different n-alkanes and squalane as well as a wax, a slack wax, a extract from the solvent raffination and a atmospheric crude oil residue. The aim was to investigate the influence of the molare weight, the structure and the composition of mixture on the solubility of methane. The pressure was varied in the region to 120 bar, the temperature was predominantly 75 C. The influence of the temperature on the solubility of methane was studied in the slack wax and the atmospheric residue. The results and the advantage as well as the disadvantage of the using of the magnetic suspension balance will be discussed. (orig.)

  14. Development of high-adhesion and boiling water-resistant glass paint%高附着耐水煮玻璃漆的研制

    Institute of Scientific and Technical Information of China (English)

    刘忠; 沈球旺; 周荣华; 崔岳崧

    2009-01-01

    合成了玻璃环氧底漆,讨论了附着力促进剂、树脂和固化剂种类及用量对涂料性能的影响.结果表明,以1.5%3-缩水甘油醚氧基丙基三甲氧基硅烷为附着力促进剂,以E-20环氧树脂为成膜物、腰果壳油改性酚醛胺为固化剂制成底漆,配合丙烯酸聚氨酯黑面漆,获得了高附着,耐水煮的玻璃漆.%An epoxy primer used on glass was synthesized, and the effects of categories and dosages of adhesion promoters, resins and curing agents were discussed. The results showed that a glass paint with high adhesion and boiling water resistance is obtained when acrylic polyurethane black top paint is combined with the primer prepared with 1.5% of 3-glycidoxypropyltrimethoxysilane as adhesion promoter, E-20 epoxy resin as film-forming material and cashew nut oil modified phenolic aldehyde amine as curing agent.

  15. Explosive Boiling at Very Low Heat Fluxes: A Microgravity Phenomenon

    Science.gov (United States)

    Hasan, M. M.; Lin, C. S.; Knoll, R. H.; Bentz, M. D.

    1993-01-01

    The paper presents experimental observations of explosive boiling from a large (relative to bubble sizes) flat heating surface at very low heat fluxes in microgravity. The explosive boiling is characterized as either a rapid growth of vapor mass over the entire heating surface due to the flashing of superheated liquid or a violent boiling spread following the appearance of single bubbles on the heating surface. Pool boiling data with saturated Freon 113 was obtained in the microgravity environment of the space shuttle. The unique features of the experimental results are the sustainability of high liquid superheat for long periods and the occurrence of explosive boiling at low heat fluxes (0.2 to 1.2 kW/sq m). For a heat flux of 1.0 kW/sq m a wall superheat of 17.9 degrees C was attained in ten minutes of heating. This was followed by an explosive boiling accompanied with a pressure spike and a violent bulk liquid motion. However, at this heat flux the vapor blanketing the heating surface could not be sustained. Stable nucleate boiling continued following the explosive boiling.

  16. Experimental study on the explosive boiling in saturated liquid nitrogen

    Institute of Scientific and Technical Information of China (English)

    DONG Zhaoyi; HUAI Xiulan; LIU Dengying

    2005-01-01

    Studies on the heat-transfer characteristics of liquid nitrogen (LN2) have received increasing attention. When there is a transient high heatflux input to the LN2, explosive boiling may take place. In this paper, using the high-power short-duration pulsed laser heating method and the high-speed photography technology, the experimental result of explosive boiling in saturated LN2 is illustrated; and the two exclusive characteristics of explosive boiling in LN2: changeover time and the relative long-time adherence of the bubble cluster to the surface, are investigated.

  17. 二甲基氯硅烷生产高沸物的综合利用研究进展%Progress in Application of Methyl Chlorosilane High-Boiling Point Residue

    Institute of Scientific and Technical Information of China (English)

    高风; 李永刚; 汪民康; 张文超; 周魁; 林萌; 黄世强

    2012-01-01

    The progress of comprehensive utilization of high-boiling point residue resulting from the production of methylchlorosilane by direct method within China and abroad was reviewed. The advantages and disadvantages of the methods were also summarized, and the directions for utilization of the high-boiling point residue were pointed.%介绍了国内外应用直接法生产甲基氯硅烷过程中产生的高沸物的综合利用研究进展,总结对比了各种方法的优势和不足,展望了高沸物综合利用前景并指出其发展方向.

  18. Cryogenic Propellant Boil-Off Reduction System

    Science.gov (United States)

    Plachta, D. W.; Christie, R. J.; Carlberg, E.; Feller, J. R.

    2008-03-01

    Lunar missions under consideration would benefit from incorporation of high specific impulse propellants such as LH2 and LO2, even with their accompanying boil-off losses necessary to maintain a steady tank pressure. This paper addresses a cryogenic propellant boil-off reduction system to minimize or eliminate boil-off. Concepts to do so were considered under the In-Space Cryogenic Propellant Depot Project. Specific to that was an investigation of cryocooler integration concepts for relatively large depot sized propellant tanks. One concept proved promising—it served to efficiently move heat to the cryocooler even over long distances via a compressed helium loop. The analyses and designs for this were incorporated into NASA Glenn Research Center's Cryogenic Analysis Tool. That design approach is explained and shown herein. Analysis shows that, when compared to passive only cryogenic storage, the boil-off reduction system begins to reduce system mass if durations are as low as 40 days for LH2, and 14 days for LO2. In addition, a method of cooling LH2 tanks is presented that precludes development issues associated with LH2 temperature cryocoolers.

  19. Electrically Driven Liquid Film Boiling Experiment

    Science.gov (United States)

    Didion, Jeffrey R.

    2016-01-01

    This presentation presents the science background and ground based results that form the basis of the Electrically Driven Liquid Film Boiling Experiment. This is an ISS experiment that is manifested for 2021. Objective: Characterize the effects of gravity on the interaction of electric and flow fields in the presence of phase change specifically pertaining to: a) The effects of microgravity on the electrically generated two-phase flow. b) The effects of microgravity on electrically driven liquid film boiling (includes extreme heat fluxes). Electro-wetting of the boiling section will repel the bubbles away from the heated surface in microgravity environment. Relevance/Impact: Provides phenomenological foundation for the development of electric field based two-phase thermal management systems leveraging EHD, permitting optimization of heat transfer surface area to volume ratios as well as achievement of high heat transfer coefficients thus resulting in system mass and volume savings. EHD replaces buoyancy or flow driven bubble removal from heated surface. Development Approach: Conduct preliminary experiments in low gravity and ground-based facilities to refine technique and obtain preliminary data for model development. ISS environment required to characterize electro-wetting effect on nucleate boiling and CHF in the absence of gravity. Will operate in the FIR - designed for autonomous operation.

  20. Calculation of Boil-Off Gas (BOG Generation of KC-1 Membrane LNG Tank with High Density Rigid Polyurethane Foam by Numerical Analysis

    Directory of Open Access Journals (Sweden)

    Jeong Hyeonwon

    2017-03-01

    Full Text Available Recently, a new type of LNG tank named “KC-1 membrane LNG tank” has been developed by Korean Gas Corporation (KOGAS, and Samsung Heavy Industries (SHI is currently building KC-1 membrane type LNG carriers. Unlike other LNG tanks, the KC-1 membrane LNG tank has a single-insulation structure rather than a double-insulation structure. For a given tank’s boundary condition, heat transfer analysis is performed from the external to the internal environment of the LNG tank by numerical simulation for three tanks. In each tank, the main thermally resistant layer of insulation is assembled with a High density rigid Polyurethane Foam (H-PUF, which is blown with one of three different types of hydrofluorocarbons-namely-HFC-365mfc, 245fa, and 245fa-e (enhanced. Advantage of such blowing agents is that it has a lower Ozone Depletion Potential (ODP than HCFC-141b or carbon dioxide (CO2 that has been used in the past as well as having low thermal conductivity. A Reduced Order Model is utilized to a 3-dimensional section of the insulation to calculate equivalent thermal conductivity. The equivalent thermal conductivity of the insulation is then applied to the rest of LNG tank, reducing the size of tank simulation domain as well as computation time. Tank’s two external and internal boundary conditions used are those defined by the International Code for the Construction and Equipment of Ships Carrying Liquefied Gases in Bulk (IGC and the United States Coast Guard (USCG conditions. Boil-off Rate (BOR of the tank that has the insulation with H-PUF blown with HFC-245fa resulted in 0.0927 %/day and 0.0745 %/day for IGC and USCG conditions, respectively.

  1. Research progresses and future directions on pool boiling heat transfer

    Directory of Open Access Journals (Sweden)

    M. Kumar

    2015-12-01

    Full Text Available This paper reviews the previous work carried on pool boiling heat transfer during heating of various liquids and commodities categorized as refrigerants and dielectric fluids, pure liquids, nanofluids, hydrocarbons and additive mixtures, as well as natural and synthetic colloidal solutions. Nucleate pool boiling is an efficient and effective method of boiling because high heat fluxes are possible with moderate temperature differences. It is characterized by the growth of bubbles on a heated surface. It occurs during boiling of liquids for excess temperature ranging from 5 to 30 °C in various processes related to high vaporization of liquid for specific purposes like sugarcane juice heating for jaggery making, milk heating for khoa making, steam generation, cooling of electronic equipments, refrigeration and etcetera. In this review paper, pool boiling method during heating of liquids for specific purpose is depicted. It is inferred that enhancement in pool boiling heat transfer is a challenging and complex task. Also, recent research and use of various correlations for natural convection pool boiling is reviewed.

  2. Film boiling of mercury droplets

    Science.gov (United States)

    Baumeister, K. J.; Schoessow, G. J.; Chmielewski, C. E.

    1975-01-01

    Vaporization times of mercury droplets in Leidenfrost film boiling on a flat horizontal plate are measured in an air atmosphere. Extreme care was used to prevent large amplitude droplet vibrations and surface wetting; therefore, these data can be compared to film boiling theory. For these data, diffusion from the upper surface of the drop is a dominant mode of mass transfer from the drop. A closed-form analytical film boiling theory is developed to account for the diffusive evaporation. Reasonable agreement between data and theory is seen.

  3. Subcooled boiling of nano-particle suspensions on Pt wires

    Institute of Scientific and Technical Information of China (English)

    LI Chunhui; WANG Buxuan; PENG Xiaofeng

    2004-01-01

    An experimental investigation is conducted to explore the subcooled boiling characteristics of nano-particle suspensions on Pt wires. Some phenomena are observed for the boiling of water-SiO2 nano-particle suspensions on Pt wires. The experiments show that there exist not any evident differences for boiling of pure water and of nano-particle suspensions at high heat fluxes. However, bubble overlap phenomenon can be easily found for nano-particle suspensions at low heat fluxes, which probably results from the increase of the attracter force between bubbles and of the bubble mass.

  4. 由扩散泵硅油高沸物制备高温润滑脂的性能%Property of High Temperature Grease with High-boiling Components of Diffusion Pump Silicone Oil

    Institute of Scientific and Technical Information of China (English)

    诸国建; 郑乾亮; 沈志晨; 惠逸磷

    2015-01-01

    Two silicone high temperature greases were prepared with high-boiling components of diffusion pump silicone oil as the base oil, and metal fatty acid soap as the thickener. Experiments show that both the physical and chemical indicators of the greases are good. The high-boiling components can be thickened by metal fatty acid soap, among which the silicone grease in which a single lithium-based soap with fatty acids can be used at a temperature not higher than 120℃. The silicone high-temperature lubricant grease of lithium soap with a fatty acid complex can be used below 200℃, temperature up to 250℃ for short-term use.%以制扩散泵用硅油的高沸物为基础油、脂肪酸锂单皂或脂脂酸锂复合皂为稠化剂,制备出2种有机硅高温润滑脂。测试表明,两种润滑脂的理化指标都不错。脂肪酸金属皂能够稠化高沸物,其中用脂肪酸锂基单皂制备的有机硅润滑脂能在温度不高于120℃条件下使用;而用脂肪酸复合锂皂制备的有机硅高温润滑脂可在200℃以下使用,短期使用温度可达250℃。

  5. Enhanced heat transfer in confined pool boiling

    NARCIS (Netherlands)

    Rops, C.M.; Lindken, R.; Velthuis, J.F.M.; Westerweel, J.

    2009-01-01

    We report the results of an experimental investigation of the heat transfer during nucleate boiling on a spatially confined boiling surface. The heat flux as a function of the boiling surface temperature was measured in pool boiling pots with diameters ranging from 15 mm down to 4.5 mm. It was found

  6. Enhanced heat transfer in confined pool boiling

    NARCIS (Netherlands)

    Rops, C.M.; Lindken, R.; Velthuis, J.F.M.; Westerweel, J.

    2009-01-01

    We report the results of an experimental investigation of the heat transfer during nucleate boiling on a spatially confined boiling surface. The heat flux as a function of the boiling surface temperature was measured in pool boiling pots with diameters ranging from 15 mm down to 4.5 mm. It was found

  7. Experiments of Pool Boiling Performance (Boiling Heat Transfer and Critical Heat Flux) on Designed Micro-Structures

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Seol Ha; Kang, Jun Young; Lee, Gi Chol; Kiyofumia, Moriyama; Kim, Moo Hwan; Park, Hyun Sun [POSTECH, Pohang (Korea, Republic of)

    2015-05-15

    In general, the evaluation of the boiling performance mainly focuses on two physical parameters: boiling heat transfer (BHT) and critical heat flux (CHF). In the nuclear power plants, both BHT and CHF contribute the nuclear system efficiency and safety, respectively. In this study, BHT and CHF of the pool boiling on well-organized fabricated structured (micro scaled) surface has been evaluated. As a results, BHT change on microstructured surface shows strongly dependent on Pin-fin effect analysis. In terms of CHF, critical size of micro structure for CHF enhancement has been observed and analyzed based on the capillary wicking effect. In this study, BHT and CHF of the pool boiling on well-organized fabricated structured (micro scaled) surface has been evaluated. As a results, BHT change on microstructured surface shows strongly dependent on the roughness ratio. The extended heat transfer area contributes the boiling heat transfer increase on the structured surface, and its quantitative analysis has been performed. In terms of CHF, the critical size of micro structure for CHF enhancement has been observed and analyzed based on the capillary wicking effect. We suggested a capillary limit to CHF delay for modeling capillary induced liquid inflow through microstructured surfaces. The critical size of the capillary limit on the prepared structured surface, determined by a model, could be reasonable explanation points for the experimental results (optimal size for CHF delay). The present experimental results also showed clearly the critical size (10 - 20 μm) for CHF delay, predicted by capillary limit analysis. This study provides fundamental insight into BHT and CHF enhancement of structured surfaces, and an optimal design guide for the required CHF and boiling heat-transfer performance. Finally, this study can contribute the basic understanding of the boiling on designed microstructure surface, and it also suggest the optimal micro scaled structured surface of boiling

  8. Nanowires for enhanced boiling heat transfer.

    Science.gov (United States)

    Chen, Renkun; Lu, Ming-Chang; Srinivasan, Vinod; Wang, Zhijie; Cho, Hyung Hee; Majumdar, Arun

    2009-02-01

    Boiling is a common mechanism for liquid-vapor phase transition and is widely exploited in power generation and refrigeration devices and systems. The efficacy of boiling heat transfer is characterized by two parameters: (a) heat transfer coefficient (HTC) or the thermal conductance; (b) the critical heat flux (CHF) limit that demarcates the transition from high HTC to very low HTC. While increasing the CHF and the HTC has significant impact on system-level energy efficiency, safety, and cost, their values for water and other heat transfer fluids have essentially remained unchanged for many decades. Here we report that the high surface tension forces offered by liquids in nanowire arrays made of Si and Cu can be exploited to increase both the CHF and the HTC by more than 100%.

  9. Film boiling on vertical surfaces.

    Science.gov (United States)

    Suryanarayana, N. V.; Merte, H., Jr.

    1972-01-01

    Film boiling of a saturated liquid on a vertical surface is analyzed to determine the local heat-transfer rates as a function of height and heater-surface superheat. Experiments show that the laminar-flow model is inadequate. A turbulent-vapor-flow model is used, and the influence of the interfacial oscillations is incorporated on a semiempirical basis. Measurements of local film boiling were obtained with a transient technique using saturated liquid nitrogen.

  10. Heat transfer and pressure drop in flow boiling in microchannels

    CERN Document Server

    Saha, Sujoy Kumar

    2016-01-01

    This Brief addresses the phenomena of heat transfer and pressure drop in flow boiling in micro channels occurring in high heat flux electronic cooling. A companion edition in the Springer Brief Subseries on Thermal Engineering and Applied Science to “Critical Heat Flux in Flow Boiling in Micro channels,” by the same author team, this volume is idea for professionals, researchers and graduate students concerned with electronic cooling.

  11. Enhanced Droplet Control by Transition Boiling

    Science.gov (United States)

    Grounds, Alex; Still, Richard; Takashina, Kei

    2012-10-01

    A droplet of water on a heated surface can levitate over a film of gas produced by its own evaporation in the Leidenfrost effect. When the surface is prepared with ratchet-like saw-teeth topography, these droplets can self-propel and can even climb uphill. However, the extent to which the droplets can be controlled is limited by the physics of the Leidenfrost effect. Here, we show that transition boiling can be induced even at very high surface temperatures and provide additional control over the droplets. Ratchets with acute protrusions enable droplets to climb steeper inclines while ratchets with sub-structures enable their direction of motion to be controlled by varying the temperature of the surface. The droplets' departure from the Leidenfrost regime is assessed by analysing the sound produced by their boiling. We anticipate these techniques will enable the development of more sophisticated methods for controlling small droplets and heat transfer.

  12. An experimental analysis of flow boiling and pressure drop in a brazed plate heat exchanger for organic Rankine cycle power systems

    DEFF Research Database (Denmark)

    Desideri, Adriano; Zhang, Ji; Kærn, Martin Ryhl

    2017-01-01

    Organic Rankine cycle power systems for low quality waste heat recovery applications can play a major role in achieving targets of increasing industrial processes efficiency and thus reducing the emissions of greenhouse gases. Low capacity organic Rankine cycle systems are equipped with brazed...... and pressure drop during vaporization at typical temperatures for low quality waste heat recovery organic Rankine cycle systems are presented for the working fluids HFC-245fa and HFO-1233zd. The experiments were carried out at saturation temperatures of 100°C, 115°C and 130°C and inlet and outlet qualities...

  13. Pressure Fluctuation of 1/fα in the Film Boiling of He Ⅱ

    Institute of Scientific and Technical Information of China (English)

    张鹏; 村上正秀; 王如竹

    2002-01-01

    A detailed study of the pressure oscillation induced by the film boiling of He Ⅱ is presented. The film boiling state and the stability of the vapour film are determined by the governing parameter (i.e. the immersion depth). It is found that the power density spectrum of the pressure oscillation induced by the film boiling displays the 1/fα-behaviour. The exponent α was found to be within the range from one to two, which indicates the existence of self-organized criticality in the film boiling of He Ⅱ.

  14. Creating Highly Reliable Accountable Care Organizations.

    Science.gov (United States)

    Vogus, Timothy J; Singer, Sara J

    2016-12-01

    Accountable Care Organizations' (ACOs) pursuit of the triple aim of higher quality, lower cost, and improved population health has met with mixed results. To improve the design and implementation of ACOs we look to organizations that manage similarly complex, dynamic, and tightly coupled conditions while sustaining exceptional performance known as high-reliability organizations. We describe the key processes through which organizations achieve reliability, the leadership and organizational practices that enable it, and the role that professionals can play when charged with enacting it. Specifically, we present concrete practices and processes from health care organizations pursuing high-reliability and from early ACOs to illustrate how the triple aim may be met by cultivating mindful organizing, practicing reliability-enhancing leadership, and identifying and supporting reliability professionals. We conclude by proposing a set of research questions to advance the study of ACOs and high-reliability research.

  15. CFD for Subcooled Flow Boiling: Parametric Variations

    Directory of Open Access Journals (Sweden)

    Roland Rzehak

    2013-01-01

    Full Text Available We investigate the present capabilities of CFD for wall boiling. The computational model used combines the Euler/Euler two-phase flow description with heat flux partitioning. Very similar modeling was previously applied to boiling water under high pressure conditions relevant to nuclear power systems. Similar conditions in terms of the relevant nondimensional numbers have been realized in the DEBORA tests using dichlorodifluoromethane (R12 as the working fluid. This facilitated measurements of radial profiles for gas volume fraction, gas velocity, liquid temperature, and bubble size. Robust predictive capabilities of the modeling require that it is validated for a wide range of parameters. It is known that a careful calibration of correlations used in the wall boiling model is necessary to obtain agreement with the measured data. We here consider tests under a variety of conditions concerning liquid subcooling, flow rate, and heat flux. It is investigated to which extent a set of calibrated model parameters suffices to cover at least a certain parameter range.

  16. CHF Phenomena by Photographic Study of Boiling Behavior due to Transient Heat Inputs

    Directory of Open Access Journals (Sweden)

    Jongdoc Park

    2012-01-01

    Full Text Available The transient boiling heat transfer characteristics in a pool of water and highly wetting liquids such as ethanol and FC-72 due to an exponentially increasing heat input of various rates were investigated using the 1.0 mm diameter experimental heater shaped in a horizontal cylinder for wide ranges of pressure and subcooling. The trend of critical heat flux (CHF values in relation to the periods was divided into three groups. The CHF belonging to the 1st group with a longer period occurs with a fully developed nucleate boiling (FDNB heat transfer process. For the 2nd group with shorter periods, the direct transition to film boiling from non boiling occurs as an explosive boiling. The direct boiling transition at the CHF from non-boiling regime to film boiling occurred without a heat flux increase. It was confirmed that the initial boiling behavior is significantly affected by the property and the wettability of the liquid. The photographic observations on the vapor bubble behavior during transitions to film boiling were performed using a high-speed video camera system.

  17. FUNDAMENTALS OF HIGH PERFORMANCE ORGANIZATIONS.

    Directory of Open Access Journals (Sweden)

    Maria Lúcia Gili Massi

    2013-06-01

    Full Text Available The objective of this article is to verify whether organizations’ high performance rests on their culture, which adjusts their cultural values, strategy, and external environment. A strong organizational culture has been reported as determinant of organizations’ performance. These studies approach the influence of values guiding and adjusting the organization’s strategic actions regarding its external environment. The bibliographic research showed that there are other variables impacting of organizations’ performance and it was concluded that the objective of this study was partially achieved.

  18. Experimental Investigation of Coolant Boiling in a Half-Heated Circular Tube - Final CRADA Report

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Wenhua [Argonne National Lab. (ANL), Argonne, IL (United States); Singh, Dileep [Argonne National Lab. (ANL), Argonne, IL (United States); France, David M. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-11-01

    Coolant subcooled boiling in the cylinder head regions of heavy-duty vehicle engines is unavoidable at high thermal loads due to high metal temperatures. However, theoretical, numerical, and experimental studies of coolant subcooled flow boiling under these specific application conditions are generally lacking in the engineering literature. The objective of this project was to provide such much-needed information, including the coolant subcooled flow boiling characteristics and the corresponding heat transfer coefficients, through experimental investigations.

  19. Electrohydrodynamics of boiling on microstructured surfaces for space applications

    Science.gov (United States)

    Saccone, Giacomo; Moran, Jeffrey L.; Bucci, Matteo; Buongiorno, Jacopo; di Marco, Paolo; Mit-Nuclear Science; Engineering Team; University Of Pisa-Destec Dept. Team

    2016-11-01

    Surface wettability is a major parameter in boiling heat transfer. It affects the departure of bubbles from the boiling surface and consequently determines the maximum heat flux transferrable in safe conditions, known as critical heat flux (CHF). Surface wettability can be enhanced through passive techniques, including micro-engineered surfaces and coatings, or through active techniques, e.g. by applying a tunable electric field (electrowetting) that modifies the bubble shape in such a way as to drive bubble detachment. The latter technique is particularly interesting for space applications, where the electric field is used to create a body force that compensates for the absence of gravity. The present work is focused on boiling heat transfer on surfaces whose wettability has been modified by passive and active techniques. We have built a pool boiling apparatus composed of a micro-structured heater acting as boiling surface and an axisymmetric electrode High-speed optical and infrared imaging have been used to investigate the dynamics of boiling phenomena. The aims of this project are twofold: to achieve a superior understanding of wetting phenomena, and to improve the efficiency of cooling devices for space applications.

  20. Simulated distillation by chromatography with supercritical fluid on high boiling petroleum fractions; Simulierte Destillation hochsiedender Erdoelfraktionen basierend auf der Chromatographie mit ueberkritischen Fluiden (SFC)

    Energy Technology Data Exchange (ETDEWEB)

    Kelemidou, K. [Inst. fuer Erdoel- und Erdgasforschung (IfE), Clausthal-Zellerfeld (Germany); Severin, D. [Inst. fuer Erdoel- und Erdgasforschung (IfE), Clausthal-Zellerfeld (Germany)

    1996-01-01

    Simulated Destillation (SD) is a suitable method to characterize highboiling petroleum fractions. SD is currently based on GC, which causes a limitation of the upper boiling end. Therefore chromatography with supercritical fluid (SFC) is applied as an alternative method for SD. Five highboiling fractions were separated by short path molecular distillation from a vacuum distillation residue and investigated by SFC. The conversion of the time in the boiling point axis was performed using Polywax 655 as a calibration mixture. The reproducibility of SFC using a pressure program was tested with Polywax 655, too. The comparison of SFC and GC based SD shows that SFC is a suitable alternative for highboiling petroleum fractions. (orig.) [Deutsch] Die Siedetemperaturverteilung, ermittelt ueber die Simulierte Destillation (SD), ist zur Charaktersisierung technischer Kohlenwasserstoffgemische in hohem Masse geeignet. Bislang wurde hierzu ausschliesslich die Gaschromatographie verwendet. Da hochsiedende Fraktionen nicht komplett GC-gaengig sind, wird versucht, die Chromatographie mit ueberkritischen Fluiden (SFC) alternativ fuer die Simulierte Destillation einzusetzen. Fuenf kurzwegmolekulardestillativ aus einem Vakuumdestillationsrueckstand gewonnene Fraktionen wurden mit der SFC chromatographiert. Zur Kalibrierung der Retentionsachse in eine Siedetemperaturachse wurde das n-Alkangemisch Polywax 655 verwendet. Mit Polywax 655 wurde auch die Reproduzierbarkeit der SFC geprueft. Der Vergleich mit der Simulierten Destillation, die auf der GC beruht, zeigt, dass die SFC eine durchaus geeignete Basis fuer die Simulierte Destillation hochsiedender Erdoelfraktionen bildet. (orig.)

  1. Flow boiling in expanding microchannels

    CERN Document Server

    Alam, Tamanna

    2017-01-01

    This Brief presents an up to date summary of details of the flow boiling heat transfer, pressure drop and instability characteristics; two phase flow patterns of expanding microchannels. Results obtained from the different expanding microscale geometries are presented for comparison and addition to that, comparison with literatures is also performed. Finally, parametric studies are performed and presented in the brief. The findings from this study could help in understanding the complex microscale flow boiling behavior and aid in the design and implementation of reliable compact heat sinks for practical applications.

  2. Deep desulfurization of full range and low boiling diesel streams from Kuwait Lower Fars heavy crude

    Energy Technology Data Exchange (ETDEWEB)

    Marafi, A.; Al-Hindi, A.; Stanislaus, A. [Petroleum and Refining Department, Petroleum Research and Studies Center, Kuwait Institute for Scientific Research (Kuwait)

    2007-09-15

    Information on feed quality and, in particular, various types of sulfur compounds present in the diesel (gas oil) fractions produced form different crudes and their HDS reactivities under different operating conditions are of a great value for the optimization and economics of the deep HDS process. This paper deals with deep desulfurization of gas oils obtained from a new heavy Kuwaiti crude, namely, Lower Fars (LF) which will be processed in the future at Kuwaiti refineries. Comparative studies were carried out to examine the extent of deep HDS, and the quality of diesel product using two gas oil feeds with different boiling ranges. The results revealed that the full range diesel feed stream produced from the LF crude was very difficult to desulfurize due to its low quality caused by high aromatics content (low feed saturation) together with the presence of high concentrations of organic nitrogen compounds and sterically hindered alkyl DBTs. The low-boiling range gas oil showed better desulfurization compared with the full range gas oil, however, deep desulfurization to 50 ppm sulfur was not achieved even at a temperature as high as 380 C for both feeds. The desulfurized diesel product from the low-boiling gas-oil feed was better in quality with respect to the S, N and PNA contents and cetane index than the full-range gas-oil feed. (author)

  3. Study of film boiling collapse behavior during vapor explosion

    Energy Technology Data Exchange (ETDEWEB)

    Yagi, Masahiro; Yamano, Norihiro; Sugimoto, Jun [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Abe, Yutaka; Adachi, Hiromichi; Kobayashi, Tomoyoshi

    1996-06-01

    Possible large scale vapor explosions are safety concern in nuclear power plants during severe accident. In order to identify the occurrence of the vapor explosion and to estimate the magnitude of the induced pressure pulse, it is necessary to investigate the triggering condition for the vapor explosion. As a first step of this study, scooping analysis was conducted with a simulation code based on thermal detonation model. It was found that the pressure at the collapse of film boiling much affects the trigger condition of vapor explosion. Based on this analytical results, basic experiments were conducted to clarify the collapse conditions of film boiling on a high temperature solid ball surface. Film boiling condition was established by flooding water onto a high temperature stainless steel ball heated by a high frequency induction heater. After the film boiling was established, the pressure pulse generated by a shock tube was applied to collapse the steam film on the ball surface. As the experimental boundary conditions, materials and size of the balls, magnitude of pressure pulse and initial temperature of the carbon and stainless steel balls were varied. The transients of pressure and surface temperature were measured. It was found that the surface temperature on the balls sharply decreased when the pressure wave passed through the film on balls. Based on the surface temperature behavior, the film boiling collapse pattern was found to be categorized into several types. Especially, the pattern for stainless steel ball was categorized into three types; no collapse, collapse and reestablishment after collapse. It was thus clarified that the film boiling collapse behavior was identified by initial conditions and that the pressure required to collapse film boiling strongly depended on the initial surface temperature. The present results will provide a useful information for the analysis of vapor explosions based on the thermal detonation model. (J.P.N.)

  4. Boiling heat transfer in dilute emulsions

    CERN Document Server

    Roesle, Matthew Lind

    2013-01-01

    Boiling Heat Transfer in Dilute Emulsions synthesizes recent advances and established understanding on the subject of boiling in dilute emulsions. Experimental results from various sources are collected and analyzed, including contemporary experiments that correlate visualization with heat transfer data. Published models of boiling heat transfer in dilute emulsions, and their implementation, are described and assessed against experimental data.

  5. Surface boiling of superheated liquid

    Energy Technology Data Exchange (ETDEWEB)

    Reinke, P. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1997-01-01

    A basic vaporization mechanism that possibly affects the qualitative and quantitative prediction of the consequences of accidental releases of hazardous superheated liquids was experimentally and analytically investigated. The studies are of relevance for the instantaneous failure of a containment vessel filled with liquefied gas. Even though catastrophical vessel failure is a rare event, it is considered to be a major technological hazard. Modeling the initial phase of depressurisation and vaporization of the contents is an essential step for the subsequent analysis of the spread and dispersion of the materials liberated. There is only limited understanding of this inertial expansion stage of the superheated liquid, before gravity and atmospheric turbulence begin to dominate the expansion. This work aims at a better understanding of the vaporization process and to supply more precise source-term data. It is also intended to provide knowledge for the prediction of the behavior of large-scale releases by the investigation of boiling on a small scale. Release experiments with butane, propane, R-134a and water were conducted. The vaporization of liquids that became superheated by sudden depressurisation was studied in nucleation-site-free glass receptacles. Several novel techniques for preventing undesired nucleation and for opening the test-section were developed. Releases from pipes and from a cylindrical geometry allowed both linear one-dimensional, and radial-front two-dimensional propagation to be investigated. Releases were made to atmospheric pressure over a range of superheats. It was found that, above a certain superheat temperature, the free surface of the metastable liquid rapidly broke up and ejected a high-velocity vapor/liquid stream. The zone of intense vaporization and liquid fragmentation proceeded as a front that advanced into the test fluids. No nucleation of bubbles in the bulk of the superheated liquid was observed. (author) figs., tabs., refs.

  6. 高强度聚焦超声焦域处气泡的空化与沸腾%Cavitation and Boiling of Bubbles at the Focal Region During High Intensity Focused Ultrasound Exposure

    Institute of Scientific and Technical Information of China (English)

    钟明松; 艾慧坚

    2012-01-01

    高强度聚焦超声(HIFU)致使组织产生热凝固性坏死,是一个非常复杂的瞬态过程.焦域处气泡的空化与沸腾行为在整个损伤过程中扮演着重要的角色.本文综述国内外学者对HIFU辐照过程中相关气泡行为的研究,就焦域处气泡的空化和沸腾的产生、相关的检测手段及其与强回声、靶区温升和损伤形态的关系进行概述.%High intensity focused ultrasound (HIFU) is a very complex transient process and can cause tissue coagulation necrosis. The cavitation and boiling behaviour of bubbles in the focal region play very important roles throughout an injury process. This paper reviews the research done by domestic and foreign scholars on behaviours of bubbles in HIFU irradiation process and summarizes in the focal region bubble cavitation and boiling generation! Related detective means and relationships with hyperecho, temperature rise of the focus and injury shape.

  7. A Prototype Therapy System for Transcutaneous Application of Boiling Histotripsy.

    Science.gov (United States)

    Maxwell, Adam D; Yuldashev, Petr V; Kreider, Wayne; Khokhlova, Tatiana D; Schade, George R; Hall, Timothy L; Sapozhnikov, Oleg A; Bailey, Michael R; Khokhlova, Vera A

    2017-08-14

    Boiling histotripsy is a method of focused ultrasound surgery that noninvasively applies millisecond-length pulses with high-amplitude shock fronts to generate liquefied lesions in tissue. Such a technique requires unique outputs compared to a focused ultrasound thermal therapy apparatus, particularly to achieve high in situ pressure levels through intervening tissue. This article describes the design and characterization of a system capable of producing the necessary pressure to transcutaneously administer boiling histotripsy therapy through clinically relevant overlying tissue paths using pulses with duration up to 10 ms. A high-voltage electronic pulser was constructed to drive a 1-MHz focused ultrasound transducer to produce shock waves with amplitude capable of generating boiling within the pulse duration in tissue. The system output was characterized by numerical modeling with the 3D Westervelt equation using boundary conditions established by acoustic holography measurements of the source field. Such simulations were found to be in agreement with directly measured focal waveforms. An existing derating method for nonlinear therapeutic fields was used to estimate in situ pressure levels at different tissue depths. The system was tested in ex vivo bovine liver samples to create boiling histotripsy lesions at depths up to 7 cm. Lesions were also created through excised porcine body wall (skin, adipose, muscle) with 3-5 cm thickness. These results indicate that the system is capable of producing the necessary output for transcutaneous ablation with boiling histotripsy.

  8. Study of rapid transient explosive boiling under short-pulsed laser heating

    Institute of Scientific and Technical Information of China (English)

    JIN Renxi; HUAI Xiulan; LIU Dengying

    2004-01-01

    Using acetone, ethanol, water and acetone-water mixture as test liquids, the rapid transient explosive boiling (RTEB) taking place under short-pulsed laser heating is observed in experiment. The behaviors of temperature variation are investigated via transient temperature measurement. The vapor bubble behaviors of RTEB are captured by high-speed photography, and the difference between RTEB and normal boiling is analyzed. The boiling heat transfer of RTEB is also discussed. It shows that the character of RTEB is far different from normal boiling.

  9. Pool boiling visualization on open microchannel surfaces

    Directory of Open Access Journals (Sweden)

    Kaniowski Robert

    2017-01-01

    Full Text Available The paper presents visualization investigations into pool boiling heat transfer for open minichannel surfaces. The experiments were carried out wih saturated water at atmospheric pressure. Parallel microchannels fabricated by machining were about 0.3 mm wide and 0.2 to 0.4 mm deep. High-speed videos were used as an aid to understanding the heat transfer mechanism. The visualization study aimed at identifying nucleation sites of the departing bubbles and determining their diameters and frequency at various superheats.

  10. Subcooled pool boiling CHF in ethanol

    OpenAIRE

    Park, Jongdoc; Fukuda, Katsuya; Liu, Qiusheng

    2006-01-01

    Steady-state and transient critical heat fluxes (CHFs) were measured using a 1.0 mm diameter horizontal cylinder in a pool of highly wetting liquid, such as ethanol, due to steady and transient heat generation rate for wide range of subcoolings and pressures. Boiling CHF was assumed to happen based on a kind of hydrodynamic instability (HI) at CHF, and the model is supposed that the increase in vapor generation from the cylinder surface causes a limit of the steady-state vapor escape flow whe...

  11. Educational Management Organizations as High Reliability Organizations: A Study of Victory's Philadelphia High School Reform Work

    Science.gov (United States)

    Thomas, David E.

    2013-01-01

    This executive position paper proposes recommendations for designing reform models between public and private sectors dedicated to improving school reform work in low performing urban high schools. It reviews scholarly research about for-profit educational management organizations, high reliability organizations, American high school reform, and…

  12. Educational Management Organizations as High Reliability Organizations: A Study of Victory's Philadelphia High School Reform Work

    Science.gov (United States)

    Thomas, David E.

    2013-01-01

    This executive position paper proposes recommendations for designing reform models between public and private sectors dedicated to improving school reform work in low performing urban high schools. It reviews scholarly research about for-profit educational management organizations, high reliability organizations, American high school reform, and…

  13. Experimental Study on Boiling Crisis in Pool Boiling

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Satbyoul; Kim, Hyungdae [Kyung Hee University, Yongin (Korea, Republic of)

    2016-10-15

    They postulated that failure in re-wetting of a dry patch by a cooling liquid is governed by microhydrodynamics near the wall. Chu et al. commonly observed that active coalescence of newly generated bubbles with preexisting bubbles results in a residual dry patch and prevents the complete rewetting of the dry patch, leading to CHF. In this work, to reveal the key physical mechanism of CHF during the rewetting process of a dry patch, dynamics of dry patches and thermal pattern of a boiling surface are simultaneously observed using TR and IR thermometry techniques. Local dynamics of dry patch and thermal pattern on a boiling surface in synchronized manner for both space and time using TR and IR thermometry were measured during pool boiling of water. Observation and quantitative examination of CHF was performed. - The hydrodynamic and thermal behaviors of irreversible dry patch were observed. The dry patches coalesce into a large dry patch and it locally dried out. Due to the failure of liquid rewetting, the dry patch is not completely rewetted, resulting in the burn out at which temperature is -140°C. - When temperature of a dry patch rises beyond the instantaneous nucleation temperature, several bubbles nucleate at the head of the advancing liquid meniscus and prevents the liquid front, and eventually the overheated dry patch remains alive after the departure of the massive bubble.

  14. Acoustic monitoring of sodium boiling in a liquid metal fast breeder reactor from autoregressive models

    Energy Technology Data Exchange (ETDEWEB)

    Geraldo, Issa Cherif [Laboratoire d’Automatique, Génie Informatique et Signal (LAGIS UMR CNRS 8219), Université Lille 1, Sciences et technologies, Avenue Paul Langevin, BP 48, 59651 Villeneuve d’Ascq CEDEX (France); Bose, Tanmoy [Indian Institute of Technology Kharagpur, Kharagpur 721302, West Bengal (India); Pekpe, Komi Midzodzi, E-mail: midzodzi.pekpe@univ-lille1.fr [Laboratoire d’Automatique, Génie Informatique et Signal (LAGIS UMR CNRS 8219), Université Lille 1, Sciences et technologies, Avenue Paul Langevin, BP 48, 59651 Villeneuve d’Ascq CEDEX (France); Cassar, Jean-Philippe [Laboratoire d’Automatique, Génie Informatique et Signal (LAGIS UMR CNRS 8219), Université Lille 1, Sciences et technologies, Avenue Paul Langevin, BP 48, 59651 Villeneuve d’Ascq CEDEX (France); Mohanty, A.R. [Indian Institute of Technology Kharagpur, Kharagpur 721302, West Bengal (India); Paumel, Kévin [CEA, DEN, Nuclear Technology Department, F-13108 Saint-Paul-lez-Durance (France)

    2014-10-15

    Highlights: • The work deals with sodium boiling detection in a liquid metal fast breeder reactor. • The authors choose to use acoustic data instead of thermal data. • The method is designed to not to be disturbed by the environment noises. • A real time boiling detection methods are proposed in the paper. - Abstract: This paper deals with acoustic monitoring of sodium boiling in a liquid metal fast breeder reactor (LMFBR) based on auto regressive (AR) models which have low computational complexities. Some authors have used AR models for sodium boiling or sodium–water reaction detection. These works are based on the characterization of the difference between fault free condition and current functioning of the system. However, even in absence of faults, it is possible to observe a change in the AR models due to the change of operating mode of the LMFBR. This sets up the delicate problem of how to distinguish a change in operating mode in absence of faults and a change due to presence of faults. In this paper we propose a new approach for boiling detection based on the estimation of AR models on sliding windows. Afterwards, classification of the models into boiling or non-boiling models is made by comparing their coefficients by two statistical methods, multiple linear regression (LR) and support vectors machines (SVM). The proposed approach takes into account operating mode information in order to avoid false alarms. Experimental data include non-boiling background noise data collected from Phenix power plant (France) and provided by the CEA (Commissariat à l’Energie Atomique et aux énergies alternatives, France) and boiling condition data generated in laboratory. High boiling detection rates as well as low false alarms rates obtained on these experimental data show that the proposed method is efficient for boiling detection. Most importantly, it shows that the boiling phenomenon introduces a disturbance into the AR models that can be clearly detected.

  15. On mechanism of explosive boiling in nanosecond regime

    Science.gov (United States)

    Çelen, Serap

    2016-06-01

    Today laser-based machining is used to manufacture vital parts for biomedical, aviation and aerospace industries. The aim of the paper is to report theoretical, numerical and experimental investigations of explosive boiling under nanosecond pulsed ytterbium fiber laser irradiation. Experiments were performed in an effective peak power density range between 1397 and 1450 MW/cm2 on pure titanium specimens. The threshold laser fluence for phase explosion, the pressure and temperature at the target surface and the velocity of the expulsed material were reported. A narrow transition zone was realized between the normal vaporization and phase explosion fields. The proof of heterogeneous boiling was given with detailed micrographs. A novel thermal model was proposed for laser-induced splashing at high fluences. Packaging factor and scattering arc radius terms were proposed to state the level of the melt ejection process. Results of the present investigation explain the explosive boiling during high-power laser interaction with metal.

  16. Technology of high-temperature organic coolant

    Energy Technology Data Exchange (ETDEWEB)

    Vorobei, M.P.; Makin, R.S.; Kuprienko, V.A. [and others

    1993-12-31

    A wide range of studies were carried out in RIAR on the problems connected with the use of high-temperature organic coolant at nuclear power plants. The work performed and successful experience gained in persistent operation of the ARBUS reactor confirmed the inherent safety characteristics, high operational reliability, as well as improved safety of stations with similar reactors. A large scope of studies were carried out at the ARBUS pilot reactor and loop with the organic coolant of the MIR reactor and a wide range of problems were solved. The studies are described.

  17. Unsteady heat transfer during subcooled film boiling

    Science.gov (United States)

    Yagov, V. V.; Zabirov, A. R.; Lexin, M. A.

    2015-11-01

    Cooling of high-temperature bodies in subcooled liquid is of importance for quenching technologies and also for understanding the processes initiating vapor explosion. An analysis of the available experimental information shows that the mechanisms governing heat transfer in these processes are interpreted ambiguously; a more clear-cut definition of the Leidenfrost temperature notion is required. The results of experimental observations (Hewitt, Kenning, and previous investigations performed by the authors of this article) allow us to draw a conclusion that there exists a special mode of intense heat transfer during film boil- ing of highly subcooled liquid. For revealing regularities and mechanisms governing intense transfer of energy in this process, specialists of Moscow Power Engineering Institute's (MPEI) Department of Engineering Thermal Physics conduct systematic works aimed at investigating the cooling of high-temperature balls made of different metals in water with a temperature ranging from 20 to 100°C. It has been determined that the field of temperatures that takes place in balls with a diameter of more than 30 mm in intense cooling modes loses its spherical symmetry. An approximate procedure for solving the inverse thermal conductivity problem for calculating the heat flux density on the ball surface is developed. During film boiling, in which the ball surface temperature is well above the critical level for water, and in which liquid cannot come in direct contact with the wall, the calculated heat fluxes reach 3-7 MW/m2.

  18. Heater size effect on subcooled pool boiling of FC-72

    Energy Technology Data Exchange (ETDEWEB)

    Raj, Rishi; Kim, Jungho [University of Maryland, College Park, MD (United States). Dept. of Mechanical Engineering

    2009-07-01

    Extensive research has been conducted on pool boiling using heaters larger than the capillary length. For large heaters and/or high gravity conditions, boiling is dominated by buoyancy, and the heat transfer is heater size independent. Much less is known about boiling on small heaters and at low gravity levels. The ratio of heater size L{sub h} to capillary length L{sub c} is an important parameter in the determination of heater size dependence on heat transfer. As the ratio L{sub h}/L{sub c} decreases due to a decrease in either heater size or gravity, surface tension forces become dominant. It is proposed that transition from buoyancy to surface tension dominated boiling occurs when the heater size and bubble departure diameter are of the same order. Previous work in variable gravity with flat surfaces has shown that the heat transfer was heater size independent only when the ratio L{sub h}/L{sub c} was considerably larger than 1. An array of 96 platinum resistance heater elements in a 10 x 10 configuration with individual elements 0.7 x 0.7 mm{sup 2} in size was used to vary heater size and measure the heat transfer. The threshold value of L{sub h}/L{sub c} above which pool boiling is heater size independent was found to be about 2.8. (author)

  19. Treatment of cork boiling wastewater using chemical oxidation and biodegradation.

    Science.gov (United States)

    Dias-Machado, Manuela; Madeira, Luis M; Nogales, Balbina; Nunes, Olga C; Manaia, Célia M

    2006-06-01

    Three cultures were enriched from cork boiling wastewater using tannic acid as the selective carbon substrate, at 25 degrees C and pH 7.2, 25 degrees C and pH 4.7 and 50 degrees C and pH 4.7. The enrichment culture obtained at neutral pH was composed of five culturable isolates, whereas from each acidic enrichment two bacterial strains were isolated. Mesophilic isolates were Gram negative bacteria belonging to the genera Klebsiella, Pseudomonas, Stenotrophomonas and Burkholderia. Thermophilic isolates were members of the genus Bacillus. Despite the capability of the enrichment cultures to use tannic acid as single carbon and energy source, those cultures were unable to reduce the total polyphenols or the total organic carbon content of cork boiling wastewater. In order to increase the bioavailability of the organic carbon in cork boiling wastewater, biodegradation was preceded by Fenton oxidation. It was demonstrated that the combined process, using small amounts of Fenton reagents and biodegradative inoculum added almost simultaneously to cork boiling wastewater, leads to TOC reductions of more than 90%.

  20. Technology of high temperature organic coolant

    Energy Technology Data Exchange (ETDEWEB)

    Makin, R.S.; Vorobei, M.P.; Kuprienko, V.A.; Starkov, V.A.; Tsykanov, V.A.; Checketkin, Y.V. [Research Institute of Atomic Reactors, Ulyanovsk (Russian Federation)

    1993-12-31

    Research has been performed on the problems related to the use of high temperature organic coolants in small and medium nuclear power plants. The work performed and also the experience of operating the ARBUS reactor confirmed the inherent safety features, reliability, and enhanced safety margins of the plants with this type of coolants. The advantages of this system and research highlights are presented.

  1. Organizing and Managing the Junior High Classroom.

    Science.gov (United States)

    Emmer, Edmund T.; And Others

    This manual provides guidelines and activities for organizing and managing junior high school classes. The first five chapters are devoted to the topic of getting ready for the beginning of the school year; the last four chapters suggest guidelines and activities that are helpful in maintaining a management system. Chapter 1 deals with organizing…

  2. Recent developments in high temperature organic polymers

    Science.gov (United States)

    Hergenrother, P. M.

    1991-01-01

    Developments in high temperature organic polymers during the last 5 years with major emphasis on polyimides and poly(arylene ether)s are discussed. Specific polymers or series of polymers have been selected to demonstrate unique properties or the effect chemical structure has upon certain properties. This article is not intended to be a comprehensive review of high temperature polymer advancements during the last 5 years.

  3. Zero boil-off system testing

    Science.gov (United States)

    Plachta, D. W.; Johnson, W. L.; Feller, J. R.

    2016-03-01

    Cryogenic propellants such as liquid hydrogen (LH2) and liquid oxygen (LO2) are a part of NASA's future space exploration plans due to their high specific impulse for rocket motors of upper stages. However, the low storage temperatures of LH2 and LO2 cause substantial boil-off losses for long duration missions. These losses can be eliminated by incorporating high performance cryocooler technology to intercept heat load to the propellant tanks and modulating the cryocooler temperature to control tank pressure. The technology being developed by NASA is the reverse turbo-Brayton cycle cryocooler and its integration to the propellant tank through a distributed cooling tubing network coupled to the tank wall. This configuration was recently tested at NASA Glenn Research Center in a vacuum chamber and cryoshroud that simulated the essential thermal aspects of low Earth orbit, its vacuum and temperature. This test series established that the active cooling system integrated with the propellant tank eliminated boil-off and robustly controlled tank pressure.

  4. Visualization of pool boiling from complex surfaces with internal tunnels

    Directory of Open Access Journals (Sweden)

    Pastuszko Robert

    2012-04-01

    Full Text Available The paper presents experimental investigations of boiling heat transfer for a system of connected narrow horizontal and vertical tunnels. These extended surfaces, named narrow tunnel structure (NTS, can be applied to electronic element cooling. The experiments were carried out with ethanol at atmospheric pressure. The tunnel external covers were manufactured out of 0.1 mm thick perforated copper foil (hole diameters 0.5 mm, sintered with the mini-fins, formed on the vertical side of the 10 mm high rectangular fins and horizontal inter-fin surface. Visualization studies were conducted with a transparent structured model of joined narrow tunnels limited with the perforated foil. The visualization investigations aimed to formulate assumptions for the boiling model through distinguishing boiling types and defining all phases of bubble growth.

  5. Micro-column enhanced boiling structure and its ramification

    Institute of Scientific and Technical Information of China (English)

    汤勇; 陆龙生; 袁冬; 苏达士

    2008-01-01

    Enhanced boiling experiments of two different enhanced structures were carried out in a thermosyphon loop evaporator chamber. One was micro-columns array structure (MCAS), which was fabricated on copper plate surface with interaction high speed wire electrode discharge machining (HS-WEDM). The other was the ramification of MCAS, named micro-column-array and sintered-copper compound structure (MSCS), which was fabricated with sintered method on micro-column array structure. Considering the wall superheat and critical heat flux (CHF), comparisons were made between them. The results show that both MCAS and MSCS can enhance the boiling heat transfer. It is also found that the enhanced boiling heat transfer ability of MSCS is changed obviously while the porosity of the sintered copper layer is changed.

  6. Research on the Characters of Boiling Heat Transfer from High Temperature Sphere to Water%高温球体与水的沸腾传热特性研究

    Institute of Scientific and Technical Information of China (English)

    沈正祥; 李金柱; 吕中杰; 黄风雷

    2013-01-01

    With the purpose of investigating the characteristics of heat transfer between high temperature liquid and water,the film boiling process from hot sphere surface was analyzed by an improved boiling model and free surface tracking method.The results show that,when the temperature of sphere is constant,the film thickness increases from stagnation point of particle,the temperature contribution decreases with non-linear posture and the velocity contribution is parabolic in film.With the increase of initial temperature of sphere,both the film thickness and peak value of vapor velocity raise,while the overall heat transfer coefficient decreases.Meanwhile,the numerical technique captures the evolution of instability at interface and the process of bubble growing,which reveal the dynamic process of boiling clearly.%为研究高温流体与水的传热特性,采用理论分析与自由界面追踪数值技术对高温球体表面的沸腾传热过程进行研究,得到球体表面传热特性的变化规律.分析结果表明,当球体温度不变时,蒸气膜层厚度自前滞点往后逐渐增大,膜层内温度呈非线性分布降低,速率呈抛物型分布.当球体温度提高时蒸气膜层厚度变大,相应的蒸气速率峰值也变大,球面传热系数却变小.数值仿真结果显示了气-液界面上不稳定性波动发展和气泡成长过程,较为真实地反映出沸腾传热的动态过程.

  7. Hysteresis of boiling for different tunnel-pore surfaces

    Directory of Open Access Journals (Sweden)

    Pastuszko Robert

    2015-01-01

    Full Text Available Analysis of boiling hysteresis on structured surfaces covered with perforated foil is proposed. Hysteresis is an adverse phenomenon, preventing high heat flux systems from thermal stabilization, characterized by a boiling curve variation at an increase and decrease of heat flux density. Experimental data were discussed for three kinds of enhanced surfaces: tunnel structures (TS, narrow tunnel structures (NTS and mini-fins covered with the copper wire net (NTS-L. The experiments were carried out with water, R-123 and FC-72 at atmospheric pressure. A detailed analysis of the measurement results identified several cases of type I, II and III for TS, NTS and NTS-L surfaces.

  8. Morphological control in polymer solar cells using low-boiling-point solvent additives

    Science.gov (United States)

    Mahadevapuram, Rakesh C.

    In the global search for clean, renewable energy sources, organic photovoltaics (OPVs) have recently been given much attention. Popular modern-day OPVs are made from solution-processible, carbon-based polymers (e.g. the model poly(3-hexylthiophene) that are intimately blended with fullerene derivatives (e.g. [6,6]-phenyl-C71-butyric acid methyl ester) to form what is known as the dispersed bulk-heterojunction (BHJ). This BHJ architecture has produced some of the most efficient OPVs to date, with reports closing in on 10% power conversion efficiency. To push efficiencies further into double digits, many groups have identified the BHJ nanomorphology---that is, the phase separations and grain sizes within the polymer: fullerene composite---as a key aspect in need of control and improvement. As a result, many methods, including thermal annealing, slow-drying (solvent) annealing, vapor annealing, and solvent additives, have been developed and studied to promote BHJ self-organization. Processing organic photovoltaic (OPV) blend solutions with high-boiling-point solvent additives has recently been used for morphological control in BHJ OPV cells. Here we show that even low-boiling-point solvents can be effective additives. When P3HT:PCBM OPV cells were processed with a low-boiling-point solvent tetrahydrafuran as an additive in parent solvent o-dichlorobenzene, charge extraction increased leading to fill factors as high as 69.5%, without low work-function cathodes, electrode buffer layers or thermal treatment. This was attributed to PCBM demixing from P3HT domains and better vertical phase separation, as indicated by photoluminescence lifetimes, hole mobilities, and shunt leakage currents. Dependence on solvent parameters and applicability beyond P3HT system was also investigated.

  9. Heat Transfer in Boiling Dilute Emulsion with Strong Buoyancy

    Science.gov (United States)

    Freeburg, Eric Thomas

    Little attention has been given to the boiling of emulsions compared to that of boiling in pure liquids. The advantages of using emulsions as a heat transfer agent were first discovered in the 1970s and several interesting features have since been studied by few researchers. Early research focuses primarily on pool and flow boiling and looks to determine a mechanism by which the boiling process occurs. This thesis looks at the boiling of dilute emulsions in fluids with strong buoyant forces. The boiling of dilute emulsions presents many favorable characteristics that make it an ideal agent for heat transfer. High heat flux electronics, such as those seen in avionics equipment, produce high heat fluxes of 100 W/cm2 or more, but must be maintained at low temperatures. So far, research on single phase convection and flow boiling in small diameter channels have yet to provide an adequate solution. Emulsions allow the engineer to tailor the solution to the specific problem. The fluid can be customized to retain the high thermal conductivity and specific heat capacity of the continuous phase while enhancing the heat transfer coefficient through boiling of the dispersed phase component. Heat transfer experiments were carried out with FC-72 in water emulsions. FC-72 has a saturation temperature of 56 °C, far below that of water. The parameters were varied as follows: 0% ≤ epsilon ≤ 1% and 1.82 x 1012 ≤ RaH ≤ 4.42 x 1012. Surface temperatures along the heated surface reached temperature that were 20 °C in excess of the dispersed phase saturation temperature. An increase of ˜20% was seen in the average Nusselt numbers at the highest Rayleigh numbers. Holography was used to obtain images of individual and multiple FC-72 droplets in the boundary layer next to the heated surface. The droplet diameters ranged from 0.5 mm to 1.3 mm. The Magnus effect was observed when larger individual droplets were injected into the boundary layer, causing the droplets to be pushed

  10. Gravity Effects in Microgap Flow Boiling

    Science.gov (United States)

    Robinson, Franklin; Bar-Cohen, Avram

    2017-01-01

    Increasing integration density of electronic components has exacerbated the thermal management challenges facing electronic system developers. The high power, heat flux, and volumetric heat generation of emerging devices are driving the transition from remote cooling, which relies on conduction and spreading, to embedded cooling, which facilitates direct contact between the heat-generating device and coolant flow. Microgap coolers employ the forced flow of dielectric fluids undergoing phase change in a heated channel between devices. While two phase microcoolers are used routinely in ground-based systems, the lack of acceptable models and correlations for microgravity operation has limited their use for spacecraft thermal management. Previous research has revealed that gravitational acceleration plays a diminishing role as the channel diameter shrinks, but there is considerable variation among the proposed gravity-insensitive channel dimensions and minimal research on rectangular ducts. Reliable criteria for achieving gravity-insensitive flow boiling performance would enable spaceflight systems to exploit this powerful thermal management technique and reduce development time and costs through reliance on ground-based testing. In the present effort, the authors have studied the effect of evaporator orientation on flow boiling performance of HFE7100 in a 218 m tall by 13.0 mm wide microgap cooler. Similar heat transfer coefficients and critical heat flux were achieved across five evaporator orientations, indicating that the effect of gravity was negligible.

  11. Gamma heated subassembly for sodium boiling experiments

    Energy Technology Data Exchange (ETDEWEB)

    Artus, S.C.

    1975-01-01

    The design of a system to boil sodium in an LMFBR is examined. This design should be regarded as a first step in a series of boiling experiments. The reactor chosen for the design of the boiling apparatus is the Experimental Breeder Reactor-II (EBR-II), located at the National Reactor Testing Station in Idaho. Criteria broadly classified as design objectives and design requirements are discussed.

  12. Blue emitting organic semiconductors under high pressure

    DEFF Research Database (Denmark)

    Knaapila, Matti; Guha, Suchismita

    2016-01-01

    This review describes essential optical and emerging structural experiments that use high GPa range hydrostatic pressure to probe physical phenomena in blue-emitting organic semiconductors including π-conjugated polyfluorene and related compounds. The work emphasizes molecular structure...... and intermolecular self-organization that typically determine transport and optical emission in π-conjugated oligomers and polymers. In this context, hydrostatic pressure through diamond anvil cells has proven to be an elegant tool to control structure and interactions without chemical intervention. This has been...... and intermolecular interactions on optical excitations, electron–phonon interaction, and changes in backbone conformations. This picture is connected to the optical high pressure studies of other π-conjugated systems and emerging x-ray scattering experiments from polyfluorenes which provides a structure-property map...

  13. Heteroarenes as high performance organic semiconductors.

    Science.gov (United States)

    Jiang, Wei; Li, Yan; Wang, Zhaohui

    2013-07-21

    The design, synthesis, and characterization of new organic semiconductors (OSCs) are important aspects for the development of next-generation optoelectronic devices. Structurally, organic semiconductors based on π-conjugated molecules can be easily modified via rational synthesis to tune multi-level self-assembled structures and discover novel chemical, optical, and electronic properties. Heteroarenes, which contain chalcogens and nitrogens in fused aromatic rings, are being developed as promising semiconducting materials for applications in a variety of electronic devices due to their outstanding optoelectronic properties. We highlight recent approaches toward realizing high performance p-channel field effect transistors based on linear heteroacenes and heteroatom annulated polycyclic aromatics (PAHs) as key functional components. These comprehensive, but carefully orchestrated approaches simultaneously address (i) practical synthesis, (ii) tunable self-assembled packing arrangement as well as (iii) high electronic performance.

  14. High pressure photophysics of organic molecules

    Energy Technology Data Exchange (ETDEWEB)

    Brey, L. A.

    1979-01-01

    High pressure spectroscopic studies on several classes of organic compounds were made both in fluid solution (to 10 kbar) and in polymeric media (to 40 kbar). The first three studies were conducted in fluid solution and concern the effect of solvent viscosity on the nonradiative deactivation rates from electronically excited states. Pressure was utilized to attain high viscosities in organic solvents at room temperature. The primary experimental technique used was fluorescence emission spectroscopy. In the fourth and last study observations were made both in fluid solution and in plastic films. The focus of this study was the effect of pressure on the solvent-chromophore dispersion interaction in several polyenes and the concomitant changes in both the radiative and non-radiative rates from the excited states. Extensive use was made of fluorescence lifetime measurements and excitation spectra. 105 references.

  15. Defluoridation of drinking water by boiling with brushite and calcite.

    Science.gov (United States)

    Larsen, M J; Pearce, E I F

    2002-01-01

    Existing methods for defluoridating drinking water involve expensive high technology or are slow, inefficient and/or unhygienic. A new method is now suggested, encompassing brushite and calcite suspension followed by boiling. Our aim was to examine the efficiency of the method and the chemical reactions involved. Brushite, 0.3-0.5 g, and an equal weight of calcite were suspended in 1 litre water containing 5-20 ppm fluoride. The suspensions were boiled in an electric kettle, left to cool and the calcium salts to sediment. Solution ion concentrations were determined and sediments were examined by X-ray diffraction. In distilled water initially containing 5, 10 and 20 ppm fluoride the concentration was reduced to 0.06, 0.4 and 5.9 ppm, respectively. Using Aarhus tap water which contained 2.6 mmol/l calcium the final concentrations were 1.2, 2.5 and 7.7 ppm, respectively, and runs without calcite gave results similar to those with calcite. Without boiling the fluoride concentration remained unaltered, as did the brushite and calcite salts, despite occasional agitation by hand. All solutions were supersaturated with respect to fluorapatite and hydroxyapatite and close to saturation with respect to brushite. Boiling produced well-crystallised apatite and traces of calcite, while boiling of brushite alone left a poorly crystallised apatite. We conclude that boiling a brushite/calcite suspension rapidly converts the two salts to apatite which incorporates fluoride if present in solution, and that this process may be exploited to defluoridate drinking water.

  16. Experimental demonstration of contaminant removal from fractured rock by boiling.

    Science.gov (United States)

    Chen, Fei; Liu, Xiaoling; Falta, Ronald W; Murdoch, Lawrence C

    2010-08-15

    This study was conducted to experimentally demonstrate removal of a chlorinated volatile organic compound from fractured rock by boiling. A Berea sandstone core was contaminated by injecting water containing dissolved 1,2-DCA (253 mg/L) and sodium bromide (144 mg/L). During heating, the core was sealed except for one end, which was open to the atmosphere to simulate an open fracture. A temperature gradient toward the outlet was observed when boiling occurred in the core. This indicates that steam was generated and a pressure gradient developed toward the outlet, pushing steam vapor and liquid water toward the outlet. As boiling occurred, the concentration of 1,2-DCA in the condensed effluent peaked up to 6.1 times higher than the injected concentration. When 38% of the pore volume of condensate was produced, essentially 100% of the 1,2-DCA was recovered. Nonvolatile bromide concentration in the condensate was used as an indicator of the produced steam quality (vapor mass fraction) because it can only be removed as a solute, and not as a vapor. A higher produced steam quality corresponds to more concentrated 1,2-DCA removal from the core, demonstrating that the chlorinated volatile compound is primarily removed by partitioning into vapor phase flow. This study has experimentally demonstrated that boiling is an effective mechanism for CVOC removal from the rock matrix.

  17. Experimental Study and Heat Transfer Analysis on the Boiling of Saturated Liquid Nitrogen under Transient Pulsed Laser Irradiation

    Institute of Scientific and Technical Information of China (English)

    Zhaoyi DONG; Xiulan HUAI

    2005-01-01

    The boiling behavior of the liquid nitrogen (LN2) under the transient high heat flux urgently needs to be researched systematically. In this paper, the high power short pulse duration laser was used to heat the saturated LN2 rapidly, and the high-speed photography aided by the spark light system was employed to take series of photos which displayed the process of LN2's boiling behavior under such conditions. Also, a special temperature measuring system was applied to record the temperature variation of the heating surface. The experiments indicated that an explosive boiling happened within LN2 by the laser heating, and a conventional boiling followed up after the newly-defined changeover time. By analyzing the temperature variation of the heating surface, it is found that the latent heat released by the crack of the bubbles in the bubble cluster induced by the explosive boiling is an important factor that greatly influences the boiling heat transfer mechanism.

  18. The Physics of Boiling at Burnout

    Science.gov (United States)

    Theofanous, T. G.; Tu, J. P.; Dinh, T. N.; Salmassi, T.; Dinh, A. T.; Gasljevic, K.

    2000-01-01

    The basic elements of a new experimental approach for the investigation of burnout in pool boiling are presented. The approach consists of the combined use of ultrathin (nano-scale) heaters and high speed infrared imaging of the heater temperature pattern as a whole, in conjunction with highly detailed control and characterization of heater morphology at the nano and micron scales. It is shown that the burnout phenomenon can be resolved in both space and time. Ultrathin heaters capable of dissipating power levels, at steady-state, of over 1 MW/square m are demonstrated. A separation of scales is identified and it is used to transfer the focus of attention from the complexity of the two-phase mixing layer in the vicinity of the heater to a micron-scaled microlayer and nucleation and associated film-disruption processes within it.

  19. Experimental study on convective boiling heat transfer in narrow-gap annulus tubes

    Institute of Scientific and Technical Information of China (English)

    LI Bin; ZHAO Jian-Fu; ZHOU Fang-De; TANG Ze-Mei; HU Wen-Rui

    2004-01-01

    Since convective boiling or highly subcooled single-phase forced convection in micro-channels is an effective cooling mechanism with a wide range of applications, more experimental and theoretical studies are required to explain and verify the forced convection heat transfer phenomenon in narrow channels. In this experimental study, we model the convective boiling behavior of water with low latent heat substance Freon 113 (R-113), with the purpose of saving power consumption and visualizing experiments. Both heat transfer and pressure drop characteristics were measured in subcooled and saturated concentric narrow gap forced convection boiling. Data were obtained to qualitatively identify the effects of gap size, pressure, flow rate and wall superheat on boiling regimes and the transition between various regimes. Some significant differences from unconfined forced convection boiling were found,and also, the flow patterns in narrow vertical annulus tubes have been studied quantitatively.

  20. Boiling flow through diverging microchannel

    Indian Academy of Sciences (India)

    V S Duryodhan; S G Singh; Amit Agrawal

    2013-12-01

    An experimental study of flow boiling through diverging microchannel has been carried out in this work, with the aim of understanding boiling in nonuniform cross-section microchannel. Diverging microchannel of 4° of divergence angle and 146 m hydraulic diameter (calculated at mid-length) has been employed for the present study with deionised water as working fluid. Effect of mass flux (118–1182 kg/m2-s) and heat flux (1.6–19.2 W/cm2) on single and two-phase pressure drop and average heat transfer coefficient has been studied. Concurrently, flow visualization is carried out to document the various flow regimes and to correlate the pressure drop and average heat transfer coefficient to the underlying flow regime. Four flow regimes have been identified from the measurements: bubbly, slug, slug–annular and periodic dry-out/rewetting. Variation of pressure drop with heat flux shows one maxima which corresponds to transition from bubbly to slug flow. It is shown that significantly large heat transfer coefficient (up to 107 kW/m2-K) can be attained for such systems, for small pressure drop penalty and with good flow stability.

  1. Boiling process in oil coolers on porous elements

    Directory of Open Access Journals (Sweden)

    Genbach Alexander A.

    2016-01-01

    Full Text Available Holography and high-speed filming were used to reveal movements and deformations of the capillary and porous material, allowing to calculate thermo-hydraulic characteristics of boiling liquid in the porous structures. These porous structures work at the joint action of capillary and mass forces, which are generalised in the form of dependences used in the calculation for oil coolers in thermal power plants (TPP. Furthermore, the mechanism of the boiling process in porous structures in the field of mass forces is explained. The development process of water steam formation in the mesh porous structures working at joint action of gravitational and capillary forces is investigated. Certain regularities pertained to the internal characteristics of boiling in cells of porous structure are revealed, by means of a holographic interferometry and high-speed filming. Formulas for calculation of specific thermal streams through thermo-hydraulic characteristics of water steam formation in mesh structures are obtained, in relation to heat engineering of thermal power plants. This is the first calculation of heat flow through the thermal-hydraulic characteristics of the boiling process in a reticulated porous structure obtained by a photo film and holographic observations.

  2. Transient boiling crisis of cryogenic liquids

    NARCIS (Netherlands)

    Deev, [No Value; Kharitonov, VS; Kutsenko, KV; Lavrukhin, AA

    2004-01-01

    This paper introduces a new physical model of boiling crisis under rapid increase of power on the heated surface. The calculation of the time interval of the transition to film boiling in cryogenic liquids was carried out depending on heat flux and pressure. The obtained results are in good

  3. Transient boiling crisis of cryogenic liquids

    NARCIS (Netherlands)

    Deev, [No Value; Kharitonov, VS; Kutsenko, KV; Lavrukhin, AA

    2004-01-01

    This paper introduces a new physical model of boiling crisis under rapid increase of power on the heated surface. The calculation of the time interval of the transition to film boiling in cryogenic liquids was carried out depending on heat flux and pressure. The obtained results are in good agreemen

  4. Boiling turbulent Rayleigh-Bénard convection

    NARCIS (Netherlands)

    Lakkaraju, R.

    2013-01-01

    A fundamental understanding of liquid-vapor phase transitions, mainly boiling phenomenon, is essential due to its omnipresence in science and technology. In industries, many empirical correlations exist on the heat transport to get an optimized and efficient thermal design of the boiling equipment.

  5. Boiling turbulent Rayleigh-Bénard convection

    NARCIS (Netherlands)

    Lakkaraju, R.

    2013-01-01

    A fundamental understanding of liquid-vapor phase transitions, mainly boiling phenomenon, is essential due to its omnipresence in science and technology. In industries, many empirical correlations exist on the heat transport to get an optimized and efficient thermal design of the boiling equipment.

  6. Heat Transfer Performances of Pool Boiling on Metal-Graphite Composite Surfaces

    Science.gov (United States)

    Zhang, Nengli; Chao, David F.; Yang, Wen-Jei

    2000-01-01

    Nucleate boiling, especially near the critical heat flux (CHF), can provide excellent economy along with high efficiency of heat transfer. However, the performance of nucleate boiling may deteriorate in a reduced gravity environment and the nucleate boiling usually has a potentially dangerous characteristic in CHF regime. That is, any slight overload can result in burnout of the boiling surface because the heat transfer will suddenly move into the film-boiling regime. Therefore, enhancement of nucleate boiling heat transfer becomes more important in reduced gravity environments. Enhancing nucleate boiling and critical heat flux can be reached using micro-configured metal-graphite composites as the boiling surface. Thermocapillary force induced by temperature difference between the graphite-fiber tips and the metal matrix, which is independent of gravity, will play an important role in bubble detachment. Thus boiling heat transfer performance does not deteriorate in a reduced-gravity environment. Based on the existing experimental data, and a two-tier theoretical model, correlation formulas are derived for nucleate boiling on the copper-graphite and aluminum-graphite composite surfaces, in both the isolated and coalesced bubble regimes. Experimental studies were performed on nucleate pool boiling of pentane on cooper-graphite (Cu-Gr) and aluminum-graphite (Al-Gr) composite surfaces with various fiber volume concentrations for heat fluxes up to 35 W per square centimeter. It is revealed that a significant enhancement in boiling heat transfer performance on the composite surfaces is achieved, due to the presence of micro-graphite fibers embedded in the matrix. The onset of nucleate boiling (the isolated bubble regime) occurs at wall superheat of about 10 C for the Cu-Gr surface and 15 C for the Al-Gr surface, much lower than their respective pure metal surfaces. Transition from an isolated bubble regime to a coalesced bubble regime in boiling occurs at a superheat of

  7. Very High Performance Organic Photonic Devices

    Science.gov (United States)

    2008-01-15

    warta,.w. Stehie, R.& Karl, N, Ultraput. high moability organic pluonocondluctors. Appi Phys. A36. cold weld. Finally, the strike layer between the...Roman, and 0. Inganas. J1. AppI . Phys. C. Silva. Phys. Rev. Lett. 92, 247402 (2004). 86. 487 (1999). 36T Offermans, P. A. van Hal, S. C. J. Meskers. M... AppI . Phys. 97. 103706 093502( (2005). (2005). 38K. L. Mutolo. E. 1. Mayo, B. P. Rand, S. R. Forre%t. and M. E. 27 . Riedel. J. Parisi. V. Dyakonov. L

  8. Boiling as Household Water Treatment in Cambodia: A Longitudinal Study of Boiling Practice and Microbiological Effectiveness

    Science.gov (United States)

    Brown, Joseph; Sobsey, Mark D.

    2012-01-01

    This paper focuses on the consistency of use and microbiological effectiveness of boiling as it is practiced in one study site in peri-urban Cambodia. We followed 60 randomly selected households in Kandal Province over 6 months to collect longitudinal data on water boiling practices and effectiveness in reducing Escherichia coli in household drinking water. Despite > 90% of households reporting that they used boiling as a means of drinking water treatment, an average of only 31% of households had boiled water on hand at follow-up visits, suggesting that actual use may be lower than self-reported use. We collected 369 matched untreated and boiled water samples. Mean reduction of E. coli was 98.5%; 162 samples (44%) of boiled samples were free of E. coli (boiled water in a covered container was associated with safer product water than storage in an uncovered container. PMID:22826487

  9. Boiling of the interface between two immiscible liquids below the bulk boiling temperatures of both components.

    Science.gov (United States)

    Pimenova, Anastasiya V; Goldobin, Denis S

    2014-11-01

    We consider the problem of boiling of the direct contact of two immiscible liquids. An intense vapour formation at such a direct contact is possible below the bulk boiling points of both components, meaning an effective decrease of the boiling temperature of the system. Although the phenomenon is known in science and widely employed in technology, the direct contact boiling process was thoroughly studied (both experimentally and theoretically) only for the case where one of liquids is becoming heated above its bulk boiling point. On the contrary, we address the case where both liquids remain below their bulk boiling points. In this paper we construct the theoretical description of the boiling process and discuss the actualisation of the case we consider for real systems.

  10. Fluid phase thermodynamics : I) nucleate pool boiling of oxygen under magnetically enhanced gravity and II) superconducting cavity resonators for high-stability frequency references and precision density measurements of helium-4 gas

    Science.gov (United States)

    Corcovilos, Theodore Allen

    Although fluids are typically the first systems studied in undergraduate thermodynamics classes, we still have only a rudimentary phenomenological understanding of these systems outside of the classical and equilibrium regimes. Two experiments will be presented. First, we present progress on precise measurements of helium-4 gas at low temperatures (1 K-5 K). We study helium because at low densities it is an approximately ideal gas but at high densities the thermodynamic properties can be predicted by numerical solutions of Schroedinger's equation. By utilizing the high resolution and stability in frequency of a superconducting microwave cavity resonator we can measure the dielectric constant of helium-4 to parts in 109, corresponding to an equivalent resolution in density. These data will be used to calculate the virial coefficients of the helium gas so that we may compare with numerical predictions from the literature. Additionally, our data may allow us to measure Boltzmann's constant to parts in 108, a factor of 100 improvement over previous measurements. This work contains a description of the nearly-completed apparatus and the methods of operation and data analysis for this experiment. Data will be taken by future researchers.The second experiment discussed is a study of nucleate pool boiling. To date, no adequate quantitative model exists of this everyday phenomenon. In our experiment, we vary one parameter inaccessible to most researchers, gravity, by applying a magnetic force to our test fluid, oxygen. Using this technique, we may apply effective gravities of 0-80 times Earth's gravitational acceleration (g). In this work we present heat transfer data for the boiling of oxygen at one atmosphere ambient pressure for effective gravity values between 1g and 16g . Our data describe two relationships between applied heat flux and temperature differential: at low heat flux the system obeys a power law and at high heat flux the behavior is linear. We find that the

  11. High Reliability Organizations--Medication Safety.

    Science.gov (United States)

    Yip, Luke; Farmer, Brenna

    2015-06-01

    High reliability organizations (HROs), such as the aviation industry, successfully engage in high-risk endeavors and have low incidence of adverse events. HROs have a preoccupation with failure and errors. They analyze each event to effect system wide change in an attempt to mitigate the occurrence of similar errors. The healthcare industry can adapt HRO practices, specifically with regard to teamwork and communication. Crew resource management concepts can be adapted to healthcare with the use of certain tools such as checklists and the sterile cockpit to reduce medication errors. HROs also use The Swiss Cheese Model to evaluate risk and look for vulnerabilities in multiple protective barriers, instead of focusing on one failure. This model can be used in medication safety to evaluate medication management in addition to using the teamwork and communication tools of HROs.

  12. Boiling on fins with wire screen of variable effective conductivity

    Directory of Open Access Journals (Sweden)

    Orzechowski Tadeusz

    2017-01-01

    Full Text Available The high scale of integration of modern equipment used for medical, military and other purposes puts heavy demands as regards the removal of great heat fluxes. This can be achieved only in exchangers that apply the phase change phenomena. Among many methods to improve boiling heat transfer, the wire mesh covering demonstrates some advantages due to the possibilities of designing the desired microstructure parameters, availability on the market, and low cost. The wire mesh microstucture with specified geometrical parameters produces anisotropy in conductivity. The different arrangement of the mesh layers relative to the direction of the heat flux is a cause of the change of temperature distribution within the layer. The consequence is a respective change in the discharge conditions of the gas phase and liquid feed. The experiments were conducted on fins covered with a single layer of copper mesh with lumen of 38 % and boiling FC-72 at ambient pressure. Compared with the smooth surface, the wire mesh structures yield an increase in the heat transfer rate at boiling. It is also shown that nucleate boiling is initiated at lower wall superheat. Formulas for longitudinal and perpendicular thermal conductivity are given for different mesh structure arrangements.

  13. On the eruptive boiling in silicon-based microchannels

    Energy Technology Data Exchange (ETDEWEB)

    Lee, P.C.; Pan, Chin [Department of Engineering and System Science, National Tsing Hua University, Hsinchu 30043 (China)

    2008-09-15

    This study investigates experimentally eruptive boiling in a silicon-based rectangular microchannel with a hydraulic diameter of 33.7 {mu}m, a width of 99.8 {mu}m and a depth-to-width ratio of 0.203. The microchannel is made of SOI wafer and prepared using bulk micro-machining and anodic bonding. The surface roughness for both the bottom and the side walls was measured using an atomic force microscope. The evolution of the eruptive boiling of water in the smooth microchannel was clearly observed using an ultra high-speed video camera (up to 50,000 frames/s) at mass fluxes of 417 and 625 kg/m{sup 2} s and a heat flux from 14.9 to 372 kW/m{sup 2}. It is confirmed that eruptive boiling is a form of rapid bubble nucleation after which the bubble merges with a slug bubble downstream in a short distance or evolve to a slug bubble. The bubble frequency in all of the cases studied is provided. Eruptive boiling may be predicted classically with nano-sized cavities that are consistent with the measured surface roughness. (author)

  14. Pool boiling on the superhydrophilic surface with TiO2 nanotube arrays

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Surface with TiO2 nanotube arrays(TNTAs)is superhydrophilic and of great specific area.This paper investigates the pool boiling characteristics at the thermal interface with TNTAs.The results show that the TNTAs interface can enhance the pool boiling heat transfer compared to the pure Ti metal plate.The bubbles formed at the initial nucleation state are very small and released in higher frequency.The pool boiling heat transfer enhancement at the TNTAs interface may be attributed to the high density of nucleate site,high intrinsic heating area of nanotubes layer,superhydrophilicity and the vertically oriented nanotube structure.

  15. Visualization of boiling flow structure in a natural circulation boiling loop

    Energy Technology Data Exchange (ETDEWEB)

    Karmakar, Arnab; Paruya, Swapan, E-mail: swapanparuya@gmail.com

    2015-04-15

    Highlights: • Vapor–liquid jet flows in natural circulation boiling loop. • Flow patterns and their transitions during geysering instability in the loop. • Evaluation of the efficiency of the needle probe in detecting the vapor–liquid and boiling flow structure. - Abstract: The present study reports vapor–liquid jet flows, flow patterns and their transitions during geysering instability in a natural circulation boiling loop under varied inlet subcooling ΔT{sub sub} (30–50 °C) and heater power Q (4–5 kW). Video imaging, voltage measurement using impedance needle probe, measurement of local pressure and loop flow rate have been carried out in this study. Power spectra of the voltage, the pressure and the flow rate reveal that at a high ΔT{sub sub} the jet flows have long period (21.36–86.95 s) and they are very irregular with a number of harmonics. The period decreases and becomes regular with a decrease of ΔT{sub sub}. The periods of the jet flows at ΔT{sub sub} = 30–50 °C and Q = 4 kW are in close agreement with those obtained from the video imaging. The probe was found to be more efficient than the pressure sensor in detecting the jet flows within an uncertainty of 9.5% and in detecting a variety of bubble classes. Both the imaging and the probe consistently identify the bubbly flow/vapor-mushrooms transition or the bubbly flow/slug flow transition on decreasing ΔT{sub sub} or on increasing Q.

  16. Bubble and boundary layer behaviour in subcooled flow boiling

    Energy Technology Data Exchange (ETDEWEB)

    Maurus, Reinhold; Sattelmayer, Thomas [Lehrstuhl fuer Thermodynamik, Technische Universitaet Muenchen, 85747 Garching (Germany)

    2006-03-15

    Subcooled flow boiling is a commonly applied technique for achieving efficient heat transfer. In the study, an experimental investigation in the nucleate boiling regime was performed for water circulating in a closed loop at atmospheric pressure. The horizontal orientated test-section consists of a rectangular channel with a one side heated copper strip and good optical access. Various optical observation techniques were applied to study the bubble behaviour and the characteristics of the fluid phase. The bubble behaviour was recorded by the high-speed cinematography and by a digital high resolution camera. Automated image processing and analysis algorithms developed by the authors were applied for a wide range of mass flow rates and heat fluxes in order to extract characteristic length and time scales of the bubbly layer during the boiling process. Using this methodology, the bubbles were automatically analysed and the bubble size, bubble lifetime, waiting time between two cycles were evaluated. Due to the huge number of observed bubbles a statistical analysis was performed and distribution functions were derived. Using a two-dimensional cross-correlation algorithm, the averaged axial phase boundary velocity profile could be extracted. In addition, the fluid phase velocity profile was characterised by means of the particle image velocimetry (PIV) for the single phase flow as well as under subcooled flow boiling conditions. The results indicate that the bubbles increase the flow resistance. The impact on the flow exceeds by far the bubbly region and it depends on the magnitude of the boiling activity. Finally, the ratio of the averaged phase boundary velocity and of the averaged fluid velocity was evaluated for the bubbly region. (authors)

  17. Mathematical and experimental modeling of nucleate boiling heat transfer in liquid nitrogen

    Science.gov (United States)

    Fusco, Ciro

    The investigation of nucleate boiling heat transfer, because of its complexity, is usually carried out experimentally and by using phenomenological approximations. The purpose of this work is to capture the essential features of nucleate boiling heat transfer in liquid nitrogen and to formulate a theoretical description useful for the prediction of the temperature fluctuations and beat flux. Experimental analysis was coupled with mathematical modeling to elucidate nucleate boiling heat transfer. The experimental setting consists of a platinum wire immersed in liquid nitrogen. A current is passed through the wire while the resistance is measured. The orientation of the wire can be changed from horizontal to vertical. The fluctuations of the wire temperature are measured. Using high-speed analysis, we characterized nucleate boiling heat transfer from the wire as occurring in two distinct phases or regimes: discrete nucleate boiling and transition boiling. We defined discrete nucleate boiling as the phase during which the active nucleation sites are clearly distinguishable from one another with no bubble coalescence occurring between adjacent sites. The high-speed analysis helped also to compute the frequencies, diameters, and nucleation density of departing bubbles as well as the energy loss by a single bubble during the discrete nucleate boiling regime. These parameters were subsequently used to formulate a mathematical model to simulate by discrete time steps the discrete nucleate boiling heat transfer from the platinum wire. The average temperature of the wire can be adequately modeled with only one variable, the power input. In addition to predicting the average temperature of the wire in the discrete nucleate boiling regime the model predicts well the average temperature of the wire in the conduction and convection regime and the transition regime. The model also reproduces the fluctuation of temperature in the discrete nucleate boiling regime. The mathematical

  18. Nucleate Pool Boiling Experiments (NPBX) on the International Space Station

    Science.gov (United States)

    Dhir, Vijay Kumar; Warrier, Gopinath R.; Aktinol, Eduardo; Chao, David; Eggers, Jeffery; Sheredy, William; Booth, Wendell

    2012-11-01

    During the period of March-May 2011, a series of boiling experiments was carried out in the Boiling Experimental Facility (BXF) located in the Microgravity Science Glovebox (MSG) of the International Space Station (ISS). The BXF Facility was carried to ISS on Space Shuttle Mission STS-133 on February 24, 2011. Nucleate Pool Boiling Experiment (NPBX) was one of the two experiments housed in the BXF. Results of experiments on single bubble dynamics (e.g., inception and growth), multiple bubble dynamics (lateral merger and departure, if any), nucleate pool boiling heat transfer, and critical heat flux are described. In the experiments Perfluoro-n-hexane was used as the test liquid. The system pressure was varied from 51 to 243 kPa, pool temperature was varied from 30° to 59°C, and test surface temperature was varied from 40° to 80°C. The test surface was a polished aluminum disc (1 mm thick, 89.5 mm in diameter) heated from below with strain gage heaters. Five cylindrical cavities were formed on the surface with four cavities located at the corners of a square and one in the middle. During experiments the magnitude of mean gravity level normal to the heater surface varied from 1.2 × 10 - 7g e to 6 × 10 - 7g e . The results of the experiments show that a single bubble continues to grow to occupy the size of the chamber without departing from the heater surface. During lateral merger of bubbles, at high superheats a large bubble may lift off from the surface but continues to hover near the surface. Neighboring bubbles are continuously pulled into the large bubble. At low superheats bubbles at neighboring sites simply merge to yield a larger bubble. The larger bubble mostly locates in the middle of the heated surface and serves as a vapor sink. The latter mode continues to persist when boiling is occurring all over the heater surface. Heat fluxes for steady state nucleate boiling and critical heat fluxes are found to be much lower than those obtained under earth

  19. Modeling acid-gas generation from boiling chloride brines

    Directory of Open Access Journals (Sweden)

    Sonnenthal Eric

    2009-11-01

    Full Text Available Abstract Background This study investigates the generation of HCl and other acid gases from boiling calcium chloride dominated waters at atmospheric pressure, primarily using numerical modeling. The main focus of this investigation relates to the long-term geologic disposal of nuclear waste at Yucca Mountain, Nevada, where pore waters around waste-emplacement tunnels are expected to undergo boiling and evaporative concentration as a result of the heat released by spent nuclear fuel. Processes that are modeled include boiling of highly concentrated solutions, gas transport, and gas condensation accompanied by the dissociation of acid gases, causing low-pH condensate. Results Simple calculations are first carried out to evaluate condensate pH as a function of HCl gas fugacity and condensed water fraction for a vapor equilibrated with saturated calcium chloride brine at 50-150°C and 1 bar. The distillation of a calcium-chloride-dominated brine is then simulated with a reactive transport model using a brine composition representative of partially evaporated calcium-rich pore waters at Yucca Mountain. Results show a significant increase in boiling temperature from evaporative concentration, as well as low pH in condensates, particularly for dynamic systems where partial condensation takes place, which result in enrichment of HCl in condensates. These results are in qualitative agreement with experimental data from other studies. Conclusion The combination of reactive transport with multicomponent brine chemistry to study evaporation, boiling, and the potential for acid gas generation at the proposed Yucca Mountain repository is seen as an improvement relative to previously applied simpler batch evaporation models. This approach allows the evaluation of thermal, hydrological, and chemical (THC processes in a coupled manner, and modeling of settings much more relevant to actual field conditions than the distillation experiment considered. The actual

  20. Modeling acid-gas generation from boiling chloride brines

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Guoxiang; Spycher, Nicolas; Sonnenthal, Eric; Steefel, Carl

    2009-11-16

    This study investigates the generation of HCl and other acid gases from boiling calcium chloride dominated waters at atmospheric pressure, primarily using numerical modeling. The main focus of this investigation relates to the long-term geologic disposal of nuclear waste at Yucca Mountain, Nevada, where pore waters around waste-emplacement tunnels are expected to undergo boiling and evaporative concentration as a result of the heat released by spent nuclear fuel. Processes that are modeled include boiling of highly concentrated solutions, gas transport, and gas condensation accompanied by the dissociation of acid gases, causing low-pH condensate. Simple calculations are first carried out to evaluate condensate pH as a function of HCl gas fugacity and condensed water fraction for a vapor equilibrated with saturated calcium chloride brine at 50-150 C and 1 bar. The distillation of a calcium-chloride-dominated brine is then simulated with a reactive transport model using a brine composition representative of partially evaporated calcium-rich pore waters at Yucca Mountain. Results show a significant increase in boiling temperature from evaporative concentration, as well as low pH in condensates, particularly for dynamic systems where partial condensation takes place, which result in enrichment of HCl in condensates. These results are in qualitative agreement with experimental data from other studies. The combination of reactive transport with multicomponent brine chemistry to study evaporation, boiling, and the potential for acid gas generation at the proposed Yucca Mountain repository is seen as an improvement relative to previously applied simpler batch evaporation models. This approach allows the evaluation of thermal, hydrological, and chemical (THC) processes in a coupled manner, and modeling of settings much more relevant to actual field conditions than the distillation experiment considered. The actual and modeled distillation experiments do not represent

  1. Boiling Heat Transfer to Halogenated Hydrocarbon Refrigerants

    Science.gov (United States)

    Yoshida, Suguru; Fujita, Yasunobu

    The current state of knowledge on heat transfer to boiling refrigerants (halogenated hydrocarbons) in a pool and flowing inside a horizontal tube is reviewed with an emphasis on information relevant to the design of refrigerant evaporators, and some recommendations are made for future research. The review covers two-phase flow pattern, heat transfer characteristics, correlation of heat transfer coefficient, influence of oil, heat transfer augmentation, boiling from tube-bundle, influence of return bend, burnout heat flux, film boiling, dryout and post-dryout heat transfer.

  2. 高温表面淹没过程中膜态沸腾的实验研究%Experimental Study on Film Boiling of High Temperature Surface During Immersion Quenching Process

    Institute of Scientific and Technical Information of China (English)

    刘斌; 潘良明; 陈德奇; 刘宏波

    2012-01-01

    Film boiling was widely applied in the process of metal heat treatment. The surface temperature and heat transfer coefficient of high temperature surface during immersion quenching process were experimentally studied. During the quenching process, the experimental results reveal that the transfer coefficient goes up to a peak near-lineally and then drops down at the gradually dropping temperature. The results show that the relationship between liquid level increasing speed and transfer coefficient is complicated and is not at a monotonous trend. According to the experimental results, a prediction model about the surface temperature vs time is established, which can predict the surface temperature well.%膜态沸腾在金属热处理等过程中有广泛的应用.本文研究了注水过程中高温表面膜态沸腾表面温度和表面换热系数的变化规律.实验发现:换热系数随表面温度的下降接近直线上升到最大值然后下降,液位上升速度对换热系数的影响较复杂,并不是单调的.根据实验数据,建立了表面温度随时间变化的预测模型,模型能很好地预测表面温度的变化规律.

  3. Criticality in the slowed-down boiling crisis at zero gravity.

    Science.gov (United States)

    Charignon, T; Lloveras, P; Chatain, D; Truskinovsky, L; Vives, E; Beysens, D; Nikolayev, V S

    2015-05-01

    Boiling crisis is a transition between nucleate and film boiling. It occurs at a threshold value of the heat flux from the heater called CHF (critical heat flux). Usually, boiling crisis studies are hindered by the high CHF and short transition duration (below 1 ms). Here we report on experiments in hydrogen near its liquid-vapor critical point, in which the CHF is low and the dynamics slow enough to be resolved. As under such conditions the surface tension is very small, the experiments are carried out in the reduced gravity to preserve the conventional bubble geometry. Weightlessness is created artificially in two-phase hydrogen by compensating gravity with magnetic forces. We were able to reveal the fractal structure of the contour of the percolating cluster of the dry areas at the heater that precedes the boiling crisis. We provide a direct statistical analysis of dry spot areas that confirms the boiling crisis at zero gravity as a scale-free phenomenon. It was observed that, in agreement with theoretical predictions, saturated boiling CHF tends to zero (within the precision of our thermal control system) in zero gravity, which suggests that the boiling crisis may be observed at any heat flux provided the experiment lasts long enough.

  4. Hypergravity to Explore the Role of Buoyancy in Boiling in Porous Media

    Science.gov (United States)

    Lioumbas, John S.; Krause, Jutta; Karapantsios, Thodoris D.

    2013-02-01

    Boiling in porous media is an active topic of research since it is associated with various applications, e.g. microelectronics cooling, wetted porous media as thermal barriers, food frying. Theoretical expressions customary scale boiling heat and mass transfer rates with the value of gravitational acceleration. Information obtained at low gravity conditions show a deviation from the above scaling law but refers exclusively to non-porous substrates. In addition, the role of buoyancy in boiling at varying gravitational levels (i.e. from microgravity—important to satellites and future Lunar and Martial missions, to high-g body forces—associated with fast aerial maneuvers) is still unknown since most experiments were conducted over a limited range of g-value. The present work aims at providing evidence regarding boiling in porous media over a broad range of hypergravity values. For this, a special device has been constructed for studying boiling inside porous media in the Large Diameter Centrifuge (LDC at ESA/ESTEC). LDC offers the unique opportunity to cancel the shear stresses and study only the effect of increased normal forces on boiling in porous media. The device permits measurement of the temperature field beneath the surface of the porous material and video recordings of bubble activity over the free surface of the porous material. The preliminary results presented from experiments conducted at terrestrial and hypergravity conditions, reveal for the first time the influence of increased levels of gravity on boiling in porous media.

  5. A Study of Nucleate Boiling with Forced Convection in Microgravity

    Science.gov (United States)

    Merte, Herman, Jr.

    1999-01-01

    bubble and the heater surface. The enhancement of the boiling process with low velocities in earth gravity for those orientations producing the formation of a liquid macrolayer described above, accompanied by "sliding" vapor bubbles, has been demonstrated. The enhancement was presented as a function of orientation, subcooling, and heated length, while a criterion for the heat transfer for mixed natural/forced convection nucleate boiling was given previously. A major unknown in the prediction and application of flow boiling heat transfer in microgravity is the upper limit of the heat flux for the onset of dryout (or critical heat flux - CHF), for given conditions of fluid-heater surfaces, including geometry, system pressure and bulk liquid subcooling. It is clearly understood that the behavior in microgravity will be no different than on earth with sufficiently high flow velocities, and would require no space experimentation. However, the boundary at which this takes place is still an unknown. Previous results of CHF measurements were presented for low velocity flow boiling at various orientations in earth gravity as a function of flow velocity and bulk liquid subcooling, along with preliminary measurements of bubble residence times on a flat heater surface. This showed promise as a parameter to be used in modeling the CHF, both in earth gravity and in microgravity. The objective of the work here is to draw attention to and show results of current modeling efforts for the CHF, with low velocities in earth gravity at different orientations and subcoolings. Many geometrical possibilities for a heater surface exist in flowing boiling, with boiling on the inner and outer surfaces of tubes perhaps being the most common. If the vapor bubble residence time on and departure size from the heater surface bear a relationship to the CHF, as results to be given indicate, it is important that visualization of and access to vapor bubble growth be conveniently available for research

  6. 21 CFR 872.6710 - Boiling water sterilizer.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Boiling water sterilizer. 872.6710 Section 872...) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6710 Boiling water sterilizer. (a) Identification. A boiling water sterilizer is an AC-powered device that consists of a container for boiling water...

  7. Boiling significantly promotes photodegradation of perfluorooctane sulfonate.

    Science.gov (United States)

    Lyu, Xian-Jin; Li, Wen-Wei; Lam, Paul K S; Yu, Han-Qing

    2015-11-01

    The application of photochemical processes for perfluorooctane sulfonate (PFOS) degradation has been limited by a low treatment efficiency. This study reports a significant acceleration of PFOS photodegradation under boiling condition compared with the non-boiling control. The PFOS decomposition rate increased with the increasing boiling intensity, but declined at a higher hydronium level or under oxygenation. These results suggest that the boiling state of solution resulted in higher effective concentrations of reactants at the gas-liquid interface and enhanced the interfacial mass transfer, thereby accelerating the PFOS decomposition. This study broadens our knowledge of PFOS photodegradation process and may have implications for development of efficient photodegradation technologies. Copyright © 2015 Elsevier Ltd. All rights reserved.

  8. Microlayer during boiling in narrow slot channels

    Science.gov (United States)

    Diev, Mikhail D.; Leontiev, Alexander I.

    1997-01-01

    An international space station Alpha will have a two-phase thermal control system. Boiling of a liquid ammonia will be a process of heat collection in evaporative heat exchangers. Unfortunately, only little data is available for boiling heat transfer in microgravity. Geometries of boiling channels working good in normal gravity are not appropriate in microgravity, and special means should be worked out to avoid some undesired events. From this point of view, the narrow slot channels may be assumed as a promising geometry for microgravity operation. During boiling in narrow slots, the vapor bubbles are flattened between the channel walls. The vapor phase and the channel wall are separated by a thin liquid film which is known as a microlayer. The paper presents the experimental results compared to the theoretical analysis, the paper also shows the narrow slot channels as a perspective configuration for microgravity applications.

  9. How To Boil the Perfect Egg

    Institute of Scientific and Technical Information of China (English)

    小雨

    2007-01-01

    A British inventor says he has cracked(破解)the age-old riddle(难题)of how to boil the perfect egg,get rid of(摆脱)the water. Simon Rhymes uses powerful light bulbs instead of boiling water to cook the egg. The gadget(小发明)does the job in six minutes,and then chons off(削)the top of

  10. The investigation of boiling crisis of nanofluids

    Directory of Open Access Journals (Sweden)

    Minakov Andrey

    2016-01-01

    Full Text Available Saturated boiling of nanofluids on a cylindrical heater with different diameters is experimentally studied. Studied nanofluids were prepared using distilled water and different metal oxides nanoparticles. The volume concentration of the nanoparticles was changed from 0.05 to 1%. It has been measured that the critical heat flux for nanofluids was much higher than for water. A strong dependence of CHF on the material and size of the nanoparticles and duration of boiling and size of heater was shown.

  11. Photophysics of organic molecules at high pressure

    Energy Technology Data Exchange (ETDEWEB)

    Mitchell, Dean James

    1978-01-01

    The pressure dependence of emission intensities, energies, and lifetimes of several classes of organic compounds in plastic media were investigated over the range 0-140 kilobars. The fluorescence intensity of 9-anthraldehyde, 9-acetylanthracene, and 9-benzoylanthracene increases remarkably with increasing pressure, accompanied by a large red shift in the emission spectrum. For azulene and several derivatives, the efficiency of fluorescence from both the second and first excited singlet states was pressure dependent as was the relative energy of these states. The rate of internal conversion depended strongly on the energy separating the relevant states. The energy and quantum efficiency of fluorescence for fluorenone in crystalline form and in several polymeric matrices was measured as a function of pressure. The quantum yield, ranged from 0.001 at low pressure to a maximum of about 0.1 at high pressure in paraffinic plastics. Fluorescence quantum yields and phosphorescence quantum yields and lifetimes were measured for pyrazine (P) 2,6-dimethylpyrazine and tetramethylpyrazine (TMP) in PMMA over the pessure range 20-120 kbar. An additional emission, which is attributed to excimer fluorescence, was also observed for these samples and for crystalline pyrazine. The phosphorescence radiative lifetime for P and TMP was about 18 ms.

  12. Flow boiling heat transfer in circulating fluidized bed

    Institute of Scientific and Technical Information of China (English)

    Xiaoguang REN; Jiangdong ZHENG; Sefiane KHELLII; Arumemi-Ikhide MICHAEL

    2009-01-01

    In order to enhance heat transfer and mitigate contamination in the boiling processes, a new type of vapor-liquid-solid (3-phase) circulating fluidized bed boil-ing system has been designed, combining a circulating fluidized bed with boiling heat transfer. Experimental results show an enhancement of the boiling curve. Flow visualization studies concerning flow hydrodynamics within the riser column are also conducted whose results are presented and discussed.

  13. Investigation of film boiling thermal hydraulics under FCI conditions. Results of a numerical study

    Energy Technology Data Exchange (ETDEWEB)

    Dinh, T.N.; Dinh, A.T.; Nourgaliev, R.R.; Sehgal, B.R. [Div. of Nuclear Power Safety Royal Inst. of Tech. (RIT), Brinellvaegen 60, 10044 Stockholm (Sweden)

    1998-01-01

    Film boiling on the surface of a high-temperature melt jet or of a melt particle is one of key phenomena governing the physics of fuel-coolant interactions (FCIs) which may occur during the course of a severe accident in a light water reactor (LWR). A number of experimental and analytical studies have been performed, in the past, to address film boiling heat transfer and the accompanying hydrodynamic aspects. Most of the experiments have, however, been performed for temperature and heat flux conditions, which are significantly lower than the prototypic conditions. For ex-vessel FCIs, high liquid subcooling can significantly affect the FCI thermal hydraulics. Presently, there are large uncertainties in predicting natural-convection film boiling of subcooled liquids on high-temperature surfaces. In this paper, research conducted at the Division of Nuclear Power Safety, Royal Institute of Technology (RIT/NPS), Stockholm, concerning film-boiling thermal hydraulics under FCI condition is presented. Notably, the focus is placed on the effects of (1) water subcooling, (2) high-temperature steam properties, (3) the radiation heat transfer and (4) mixing zone boiling dynamics, on the vapor film characteristics. Numerical investigations are performed using a novel CFD modeling concept named as the local-homogeneous-slip model (LHSM). Results of the analytical and numerical studies are discussed with respect to boiling dynamics under FCI conditions. (author)

  14. Pressure gradients and boiling as mechanisms for localizing ore in porphyry systems

    Science.gov (United States)

    Cunningham, Charles G.

    1978-01-01

    Fluid inclusions in ore zones of porphyry systems indicate that extensive boiling of hydrothermal fluids accompanies deposition of ore and gangue minerals. The boiling commonly accompanied a change from a lithostatic to a hydrostatic environment during evolution of an epizonal stock. Pressure gradients near the margin of the stock can determine whether ore or only a diffuse zone of mineralization is formed. A sharp drop in pressure in an epizonal environment is more likely to cause extensive boiling than a comparable change in a deeper environment, as the slope of the boiling curve steepens with an increase 'in pressure. The drop in pressure causes the hydrothermal fluids to boil and creates a crackle (stockwork) breccia, which hosts the veinlets of gangue quartz and ore minerals. The boiling selectively partitions CO2, H2S, and HCl into the vapor phase, changing the pH, composition, ionic strength, and thus the solubility product of metal complexes in the remaining liquid and causing the ore and gangue to come out of solution. Fluid inclusions trapped from boiling solutions can exhibit several forms, depending on the physical and chemical conditions of the hydrothermal fluid from which they were trapped. In one case, inclusions when heated can homogenize to either liquid or vapor at the same temperature, which is the true boiling temperature. In another case, homogenization of various inclusions can occur through a range of temperatures. The latter case results from the trapping of mixture of liquid and vapor. Variations in salinity can result from boiling of the hydrothermal fluid, or intermittent incorporation of high-salinity fluids from the magma, or trapping of fluids of varying densities at pressure-temperature conditions above the critical point of the fluid. In places, paleopressure-temperature transition zones can be recognized by fluid-inclusion homogenization temperatures and phase relationships and by the presence of anhydrite daughter minerals

  15. Boiling of simulated tap water: effect on polar brominated disinfection byproducts, halogen speciation, and cytotoxicity.

    Science.gov (United States)

    Pan, Yang; Zhang, Xiangru; Wagner, Elizabeth D; Osiol, Jennifer; Plewa, Michael J

    2014-01-01

    Tap water typically contains numerous halogenated disinfection byproducts (DBPs) as a result of disinfection, especially of chlorination. Among halogenated DBPs, brominated ones are generally significantly more toxic than their chlorinated analogues. In this study, with the aid of ultra performance liquid chromatography/electrospray ionization-triple quadrupole mass spectrometry by setting precursor ion scans of m/z 79/81, whole spectra of polar brominated DBPs in simulated tap water samples without and with boiling were revealed. Most polar brominated DBPs were thermally unstable and their levels were substantially reduced after boiling via decarboxylation or hydrolysis; the levels of a few aromatic brominated DBPs increased after boiling through decarboxylation of their precursors. A novel adsorption unit for volatile total organic halogen was designed, which enabled the evaluation of halogen speciation and mass balances in the simulated tap water samples during boiling. After boiling for 5 min, the overall level of brominated DBPs was reduced by 62.8%, of which 39.8% was volatilized and 23.0% was converted to bromide; the overall level of chlorinated DBPs was reduced by 61.1%, of which 44.4% was volatilized and 16.7% was converted to chloride; the overall level of halogenated DBPs was reduced by 62.3%. The simulated tap water sample without boiling was cytotoxic in a chronic (72 h) exposure to mammalian cells; this cytotoxicity was reduced by 76.9% after boiling for 5 min. The reduction in cytotoxicity corresponded with the reduction in overall halogenated DBPs. Thus, boiling of tap water can be regarded as a "detoxification" process and may reduce human exposure to halogenated DBPs through tap water ingestion.

  16. Critical heat flux maxima during boiling crisis on textured surfaces

    Science.gov (United States)

    Dhillon, Navdeep Singh; Buongiorno, Jacopo; Varanasi, Kripa K.

    2015-01-01

    Enhancing the critical heat flux (CHF) of industrial boilers by surface texturing can lead to substantial energy savings and global reduction in greenhouse gas emissions, but fundamentally this phenomenon is not well understood. Prior studies on boiling crisis indicate that CHF monotonically increases with increasing texture density. Here we report on the existence of maxima in CHF enhancement at intermediate texture density using measurements on parametrically designed plain and nano-textured micropillar surfaces. Using high-speed optical and infrared imaging, we study the dynamics of dry spot heating and rewetting phenomena and reveal that the dry spot heating timescale is of the same order as that of the gravity and liquid imbibition-induced dry spot rewetting timescale. Based on these insights, we develop a coupled thermal-hydraulic model that relates CHF enhancement to rewetting of a hot dry spot on the boiling surface, thereby revealing the mechanism governing the hitherto unknown CHF enhancement maxima. PMID:26346098

  17. A molecular dynamics study of phobic/philic nano-patterning on pool boiling heat transfer

    Science.gov (United States)

    Diaz, Ricardo; Guo, Zhixiong

    2017-03-01

    Molecular dynamics (MD) simulations were employed to investigate the pool boiling heat transfer of a liquid argon thin film on a flat, horizontal copper wall structured with vertical nanoscale pillars. The efficacy of phobic/philic nano-patterning for enhancing boiling heat transfer was scrutinized. Both nucleate and explosive boiling modes were considered. An error analysis demonstrated that the typical 2.5σ cutoff in MD simulations could under-predict heat flux by about 8.7 %, and 6σ cutoff was chosen here in order to maintain high accuracy. A new coordination number criterion was also introduced to better quantify evaporation characteristics. Results indicate that the argon-phobic/philic patterning tends to either have no effect, or decrease overall boiling heat flux, while the argon-philic nano-pillar/argon-philic wall shows the best heat transfer performance.

  18. Boiling crisis as inhibition of bubble detachment by the vapor recoil force

    CERN Document Server

    Nikolayev, Vadim; Garrabos, Yves

    2016-01-01

    Boiling crisis is a transition between nucleate and film boiling. In this communication we present a physical model of the boiling crisis based on the vapor recoil effect. Our numerical simulations of the thermally controlled bubble growth at high heat fluxes show how the bubble begins to spread over the heater thus forming a germ for the vapor film. The vapor recoil force not only causes the vapor spreading, it also creates a strong adhesion to the heater that prevents the bubble departure, thus favoring the further bubble spreading. Near the liquid-gas critical point, the bubble growth is very slow and allows the kinetics of the bubble spreading to be observed. Since the surface tension is very small in this regime, only microgravity conditions can preserve a convex bubble shape. Under such conditions, we observed an increase of the apparent contact angle and spreading of the dry spot under the bubble, thus confirming our model of the boiling crisis.

  19. A molecular dynamics study of phobic/philic nano-patterning on pool boiling heat transfer

    Science.gov (United States)

    Diaz, Ricardo; Guo, Zhixiong

    2016-07-01

    Molecular dynamics (MD) simulations were employed to investigate the pool boiling heat transfer of a liquid argon thin film on a flat, horizontal copper wall structured with vertical nanoscale pillars. The efficacy of phobic/philic nano-patterning for enhancing boiling heat transfer was scrutinized. Both nucleate and explosive boiling modes were considered. An error analysis demonstrated that the typical 2.5σ cutoff in MD simulations could under-predict heat flux by about 8.7 %, and 6σ cutoff was chosen here in order to maintain high accuracy. A new coordination number criterion was also introduced to better quantify evaporation characteristics. Results indicate that the argon-phobic/philic patterning tends to either have no effect, or decrease overall boiling heat flux, while the argon-philic nano-pillar/argon-philic wall shows the best heat transfer performance.

  20. A Novel Kinetic Model of Liquid Nitrogen's Explosive Boiling at the Initial Stage

    Institute of Scientific and Technical Information of China (English)

    HUAI Xiu-Lan; DONG Zhao-Yi; LI Zhi-Gang; YIN Tie-Nan; ZOU Yu

    2007-01-01

    The liquid nitrogen's explosive boiling characteristics under transient high heat flux have attracted increasing attentions of researchers over the world due to its wide applications. Although some experiments have been performed, the process and the characteristics at the initial stage, especially within 1μs, have not been described reasonably yet. Based on the related experiments and theoretical analysis, a novel kinetic model combined with quasi-fluid idea is presented to analyse the characteristics of liquid nitrogen's explosive boiling at the initial stage. The results indicate that the model can appropriately describe the liquid nitrogen's explosive boiling. The behaviour and the heat transfer characteristics of a single bubble are very different from those of the bubble cluster, thus the behaviour of individual bubbles could not be directly applied to describe the explosive boiling process at the initial stage.

  1. Experimental Investigation on Pool Boiling Heat Transfer With Ammonium Dodecyl Sulfate

    Directory of Open Access Journals (Sweden)

    Mr.P. Atcha Rao

    2015-11-01

    Full Text Available We have so many applications related to Pool Boiling. The Pool Boiling is mostly useful in arid areas to produce drinking water from impure water like sea water by distillation process. It is very difficult to distill the only water which having high surface tension. The surface tension is important factor to affect heat transfer enhancement in pool boiling. By reducing the surface tension we can increase the heat transfer rate in pool boiling. From so many years we are using surfactants domestically. It is proven previously by experiments that the addition of little amount of surfactant reduces the surface tension and increase the rate of heat transfer. There are different groups of surfactants. From those I‟m conducting experimentation with anionic surfactant Ammonium Dodecyl Sulfate (ADS, which is most human friendly and three times best soluble than Sodium Dodecyl Sulfate, to test the heat transfer enhancement.

  2. Pool boiling on rectangular fins with tunnel-pore structure

    Directory of Open Access Journals (Sweden)

    Pastuszko A.

    2013-04-01

    Full Text Available Complex experimental investigations were conducted in the area of pool boiling heat transfer on extended surfaces with internal tunnels limited by perforated foil. The experiments were carried out for water and R-123 at atmospheric pressure. The tunnel surfaces were fabricated from 0.05 – 0.1 mm thick perforated copper foil (pore diameters: 0.3, 0.4, 0.5 mm sintered with mini-fins formed by 5 and 10 mm high rectangular fins and horizontal inter-fin surface. The effect of the main fin height, pore diameters and tunnel pitch on nucleate pool boiling was examined. Substantial enhancement of heat transfer coefficient was observed for the investigated surfaces. The highest increase in the heat transfer coefficient was obtained for the 10 mm high fins – about 50kW/m2K for water and 15 kW/m2K for R-123. The investigated surfaces showed boiling heat transfer coefficients similar to those of existing tunnel-pore structures.

  3. Lattice Boltzmann modeling of boiling heat transfer: The boiling curve and the effects of wettability

    CERN Document Server

    Li, Q; Francois, M M; He, Y L; Luo, K H

    2015-01-01

    A hybrid thermal lattice Boltzmann (LB) model is presented to simulate thermal multiphase flows with phase change based on an improved pseudopotential LB approach [Q. Li, K. H. Luo, and X. J. Li, Phys. Rev. E 87, 053301 (2013)]. The present model does not suffer from the spurious term caused by the forcing-term effect, which was encountered in some previous thermal LB models for liquid-vapor phase change. Using the model, the liquid-vapor boiling process is simulated. The boiling curve together with the three boiling stages (nucleate boiling, transition boiling, and film boiling) is numerically reproduced in the LB community for the first time. The numerical results show that the basic features and the fundamental characteristics of boiling heat transfer are well captured, such as the severe fluctuation of transient heat flux in the transition boiling and the feature that the maximum heat transfer coefficient lies at a lower wall superheat than that of the maximum heat flux. Furthermore, the effects of the he...

  4. Cryogenic disturbance and its impact on soils of frost boil ecosystems of Taz peninsula, West Siberia

    Science.gov (United States)

    Myshonkov, Alexander; Matyshak, George; Petrzhik, Natalia

    2017-04-01

    different. Frost boils have lack of vegetatio and, as consequence, no organic matter in uppers pit horizons. We find organic horizon in interboil areas - it can be up to 15 cm height. Frost boils have higher moisture and temperature levels: 25,6 ±6 % and 12,5 ±0,8 °C, as compared with interboil areas: 15 ±4 % and 8,5 ±0,8 °C. Active layer is found on an average depth of 125±5 cm under the frost boils to 110±5 cm under the interboils. Chemical analysis shows that pH varies from neutral values at the bare spot ( 6-6.2) to a slightly acidic at microdepressions ( 5-5,3). These differences lead to the contrast in biological activity: CO2 flux is higher in the troughs than in spots (193 and 55 mg*m2/hour, resp.). BR results are the same: it is higher in troughs than in spots more than 10 times. Cryogenic processes actively influence on the soil formation and redistribution of substances in studied ecosystems. These facts of influence should be considered in different calculations.

  5. A review of film boiling at cryogenic temperatures.

    Science.gov (United States)

    Hsu, Y. Y.

    1972-01-01

    Film boiling occurs in the quenching of metals, the chilling of biological species, the regenerative cooling of rockets, and the cooling down of a cryogenic fuel tank. Occasionally film boiling is also found in a nuclear reactor or in a cryomagnet. Aspects of film boiling involving an unconstrained liquid mass are considered, giving attention to the evaporation time, the Leidenfrost temperature, solid-liquid contacts, the thermal properties of the solid, effects of coating or scale, wettability, the metastable condition, and the velocity effect on drops. Developments discussed with regard to pool boiling are related to vertical surfaces, film boiling from horizontal surfaces, film boiling from a horizontal cylinder, film boiling from a sphere, and film boiling of helium. Processes of film boiling in a channel are also analyzed.

  6. High-Power-Density Organic Radical Batteries.

    Science.gov (United States)

    Friebe, Christian; Schubert, Ulrich S

    2017-02-01

    Batteries that are based on organic radical compounds possess superior charging times and discharging power capability in comparison to established electrochemical energy-storage technologies. They do not rely on metals and, hence, feature a favorable environmental impact. They furthermore offer the possibility of roll-to-roll processing through the use of different printing techniques, which enables the cost-efficient fabrication of mechanically flexible devices. In this review, organic radical batteries are presented with the focus on the hitherto developed materials and the key properties thereof, e.g., voltage, capacity, and cycle life. Furthermore, basic information, such as significant characteristics, housing approaches, and applied additives, are presented and discussed in the context of organic radical batteries.

  7. High-symmetry organic scintillator systems

    Energy Technology Data Exchange (ETDEWEB)

    Feng, Patrick L.

    2017-07-18

    An ionizing radiation detector or scintillator system includes a scintillating material comprising an organic crystalline compound selected to generate photons in response to the passage of ionizing radiation. The organic compound has a crystalline symmetry of higher order than monoclinic, for example an orthorhombic, trigonal, tetragonal, hexagonal, or cubic symmetry. A photodetector is optically coupled to the scintillating material, and configured to generate electronic signals having pulse shapes based on the photons generated in the scintillating material. A discriminator is coupled to the photon detector, and configured to discriminate between neutrons and gamma rays in the ionizing radiation based on the pulse shapes of the output signals.

  8. High-symmetry organic scintillator systems

    Energy Technology Data Exchange (ETDEWEB)

    Feng, Patrick L.

    2017-09-05

    An ionizing radiation detector or scintillator system includes a scintillating material comprising an organic crystalline compound selected to generate photons in response to the passage of ionizing radiation. The organic compound has a crystalline symmetry of higher order than monoclinic, for example an orthorhombic, trigonal, tetragonal, hexagonal, or cubic symmetry. A photodetector is optically coupled to the scintillating material, and configured to generate electronic signals having pulse shapes based on the photons generated in the scintillating material. A discriminator is coupled to the photon detector, and configured to discriminate between neutrons and gamma rays in the ionizing radiation based on the pulse shapes of the output signals.

  9. Effect of Running Parameters on Flow Boiling Instabilities in Microchannels.

    Science.gov (United States)

    Zong, Lu-Xiang; Xu, Jin-Liang; Liu, Guo-Hua

    2015-04-01

    Flow boiling instability (FBI) in microchannels is undesirable because they can induce the mechanical vibrations and disturb the heat transfer characteristics. In this study, the synchronous optical visualization experimental system was set up. The pure acetone liquid was used as the working fluid, and the parallel triangle silicon microchannel heat sink was designed as the experimental section. With the heat flux ranging from 0-450 kW/m2 the microchannel demand average pressure drop-heater length (Δp(ave)L) curve for constant low mass flux, and the demand pressure drop-mass flux (Δp(ave)G) curve for constant length on main heater surface were obtained and studied. The effect of heat flux (q = 188.28, 256.00, and 299.87 kW/m2), length of main heater surface (L = 4.5, 6.25, and 8.00 mm), and mass flux (G = 188.97, 283.45, and 377.94 kg/m2s) on pressure drops (Ap) and temperatures at the central point of the main heater surface (Twc) were experimentally studied. The results showed that, heat flux, length of the main heater surface, and mass flux were identified as the important parameters to the boiling instability process. The boiling incipience (TBI) and critical heat flux (CHF) were early induced for the lower mass flux or the main heater surface with longer length. With heat flux increasing, the pressure drops were linearly and slightly decreased in the single liquid region but increased sharply in the two phase flow region, in which the flow boiling instabilities with apparent amplitude and long period were more easily triggered at high heat flux. Moreover, the system pressure was increased with the increase of the heat flux.

  10. Experimental Investigation of Flow Boiling in Parallel Mini-channels

    Science.gov (United States)

    Wu, Wan.; Zhang, M. T.; Zhang, X. B.; Xia, J. J.; Wen, S.-Z.; Wang, Z.-R.; He, Z.-H.; Huang, Z.-C.

    2015-07-01

    Flow boiling in micro-channels and mini-channels has received significant attention due to its capability for dissipating highflux heat, especially in the thermal management of high precision electronics. A heat sink with narrow rectangular mini-channels is designed to investigate flow boiling in the mini-channels, including the effect of gravity. It contains 14 parallel channels with a cross section, of 1×4mm 2, of which the hydraulic diameter is 1.6mm. The cooling capability, the temperature uniformity, and the temperature stability of the flow boiling in minichannels are investigated with R22, with total mass flow flux ranges from 35 to 70kg/m 2s. The results show that the cooling capability of the heat- sink is up to 340W(˜ 3.0W/cm 2), and the temperature difference is below 4 ∘C(even down to 2 ∘C) on the heat sink. The temperature uniformity isn't quite sensitive to heat flux. The instability has not been observed in the present researches.

  11. Boiling and quenching heat transfer advancement by nanoscale surface modification.

    Science.gov (United States)

    Hu, Hong; Xu, Cheng; Zhao, Yang; Ziegler, Kirk J; Chung, J N

    2017-07-21

    All power production, refrigeration, and advanced electronic systems depend on efficient heat transfer mechanisms for achieving high power density and best system efficiency. Breakthrough advancement in boiling and quenching phase-change heat transfer processes by nanoscale surface texturing can lead to higher energy transfer efficiencies, substantial energy savings, and global reduction in greenhouse gas emissions. This paper reports breakthrough advancements on both fronts of boiling and quenching. The critical heat flux (CHF) in boiling and the Leidenfrost point temperature (LPT) in quenching are the bottlenecks to the heat transfer advancements. As compared to a conventional aluminum surface, the current research reports a substantial enhancement of the CHF by 112% and an increase of the LPT by 40 K using an aluminum surface with anodized aluminum oxide (AAO) nanoporous texture finish. These heat transfer enhancements imply that the power density would increase by more than 100% and the quenching efficiency would be raised by 33%. A theory that links the nucleation potential of the surface to heat transfer rates has been developed and it successfully explains the current finding by revealing that the heat transfer modification and enhancement are mainly attributed to the superhydrophilic surface property and excessive nanoscale nucleation sites created by the nanoporous surface.

  12. Recent progress in high-pressure studies on organic conductors

    Directory of Open Access Journals (Sweden)

    Syuma Yasuzuka and Keizo Murata

    2009-01-01

    Full Text Available Recent high-pressure studies of organic conductors and superconductors are reviewed. The discovery of the highest Tc superconductivity among organics under high pressure has triggered the further progress of the high-pressure research. Owing to this finding, various organic conductors with the strong electron correlation were investigated under high pressures. This review includes the pressure techniques using the cubic anvil apparatus, as well as high-pressure studies of the organic conductors up to 10 GPa showing extraordinary temperature and pressure dependent transport phenomena.

  13. Pool boiling of water on nano-structured micro wires at sub-atmospheric conditions

    Science.gov (United States)

    Arya, Mahendra; Khandekar, Sameer; Pratap, Dheeraj; Ramakrishna, S. Anantha

    2016-09-01

    Past decades have seen active research in enhancement of boiling heat transfer by surface modifications. Favorable surface modifications are expected to enhance boiling efficiency. Several interrelated mechanisms such as capillarity, surface energy alteration, wettability, cavity geometry, wetting transitions, geometrical features of surface morphology, etc., are responsible for change in the boiling behavior of modified surfaces. Not much work is available on pool boiling at low pressures on microscale/nanoscale geometries; low pressure boiling is attractive in many applications wherein low operating temperatures are desired for a particular working fluid. In this background, an experimental setup was designed and developed to investigate the pool boiling performance of water on (a) plain aluminum micro wire (99.999 % pure) and, (b) nano-porous alumina structured aluminum micro wire, both having diameter of 250 µm, under sub-atmospheric pressure. Nano-structuring on the plain wire surface was achieved via anodization. Two samples, A and B of anodized wires, differing by the degree of anodization were tested. The heater length scale (wire diameter) was much smaller than the capillary length scale. Pool boiling characteristics of water were investigated at three different sub-atmospheric pressures of 73, 123 and 199 mbar (corresponding to T sat = 40, 50 and 60 °C). First, the boiling characteristics of plain wire were measured. It was noticed that at sub-atmospheric pressures, boiling heat transfer performance for plain wire was quite low due to the increased bubble sizes and low nucleation site density. Subsequently, boiling performance of nano-structured wires (both Sample A and Sample B) was compared with plain wire and it was noted that boiling heat transfer for the former was considerably enhanced as compared to the plain wire. This enhancement is attributed to increased nucleation site density, change in wettability and possibly due to enhanced pore scale

  14. Estimation of boiling points using density functional theory with polarized continuum model solvent corrections.

    Science.gov (United States)

    Chan, Poh Yin; Tong, Chi Ming; Durrant, Marcus C

    2011-09-01

    An empirical method for estimation of the boiling points of organic molecules based on density functional theory (DFT) calculations with polarized continuum model (PCM) solvent corrections has been developed. The boiling points are calculated as the sum of three contributions. The first term is calculated directly from the structural formula of the molecule, and is related to its effective surface area. The second is a measure of the electronic interactions between molecules, based on the DFT-PCM solvation energy, and the third is employed only for planar aromatic molecules. The method is applicable to a very diverse range of organic molecules, with normal boiling points in the range of -50 to 500 °C, and includes ten different elements (C, H, Br, Cl, F, N, O, P, S and Si). Plots of observed versus calculated boiling points gave R²=0.980 for a training set of 317 molecules, and R²=0.979 for a test set of 74 molecules. The role of intramolecular hydrogen bonding in lowering the boiling points of certain molecules is quantitatively discussed. Crown Copyright © 2011. Published by Elsevier Inc. All rights reserved.

  15. Burnout in subcooled flow boiling of water. A visual experimental study

    Energy Technology Data Exchange (ETDEWEB)

    Celata, G.P.; Mariani, A.; Zummo, G. [ENEA, Engineering Div., National Institute of Thermal Fluid-Dynamics, Rome (Italy); Cumo, M. [University of Rome la Sapienza, Rome (Italy)

    2000-12-01

    The objective of the present work is to perform a photographic study of the burnout in highly subcooled flow boiling, in order to provide a qualitative description of the flow pattern under different conditions of boiling regime: ONB (onset of nucleate boiling), subcooled flow boiling and thermal crisis. In particular, the flow visualisation is focused on the phenomena occurring on the heated wall during the thermal crisis up to the physical burnout of the heater. Vapour bubble parameters are measured from flow images recorded, while the wall temperature is measured with an indirect method, by recording the heater elongation during all flow regimes studied. The combination of bubble parameters and wall temperature measurements as well as direct observations of the flow pattern, for all flow regimes, are collected in graphs which provide a useful global point of view of boiling phenomena, especially during boiling crisis. Under these conditions, a detailed analysis of the mechanisms leading to the critical heat flux is reported, and the so called events sequence, from thermal crisis occurrence up to heater burnout, is illustrated. (authors)

  16. Boiling on Microconfigured Composite Surfaces Enhanced

    Science.gov (United States)

    Chao, David F.

    2000-01-01

    Boiling heat transfer is one of the key technologies for the two-phase active thermal-control system used on space platforms, as well as for the dynamic power systems aboard the International Space Station. Because it is an effective heat transfer mode, boiling is integral to many space applications, such as heat exchangers and other cooling devices. Nucleate boiling near the critical heat flux (CHF) can transport very large thermal loads with a much smaller device and much lower pumping power than for single-phase heat exchangers. However, boiling performance sharply deteriorates in a reduced-gravity environment, and operation in the CHF regime is somewhat perilous because of the risk of burnout to the device surface. New materials called microconfigured metal-graphite composites can enhance boiling. The photomicrograph shows the microconfiguration (x3000) of the copper-graphite (Cu-Gr) surface as viewed by scanning electronic microscope. The graphite fiber tips appear as plateaus with rugged surfaces embedded in the copper matrix. It has been experimentally demonstrated that this type of material manifests excellent boiling heat transfer performance characteristics and an increased CHF. Nonisothermal surfaces were less sensitive to variations of wall superheat in the CHF regime. Because of the great difference in conductivity between the copper base and the graphite fiber, the composite surfaces have a nonisothermal surface characteristic and, therefore, will have a much larger "safe" operating region in the CHF regime. In addition, the thermocapillary forces induced by the temperature differences between the fiber tips and the metal matrix play an important role in bubble detachment, and may not be adversely affected in a reduced-gravity environment. All these factors indicate that microconfigured composites may improve the reliability and economy (dominant factors in all space applications) of various thermal components found on spacecraft during future

  17. BOILING SLURRY REACTOR AND METHOD FO CONTROL

    Science.gov (United States)

    Petrick, M.; Marchaterre, J.F.

    1963-05-01

    The control of a boiling slurry nuclear reactor is described. The reactor consists of a vertical tube having an enlarged portion, a steam drum at the top of the vertical tube, and at least one downcomer connecting the steam drum and the bottom of the vertical tube, the reactor being filled with a slurry of fissionabie material in water of such concentration that the enlarged portion of the vertical tube contains a critical mass. The slurry boils in the vertical tube and circulates upwardly therein and downwardly in the downcomer. To control the reactor by controlling the circulation of the slurry, a gas is introduced into the downcomer. (AEC)

  18. Thermodynamic considerations on a boil-off gas recovery system; Considerations thermo-dynamiques sur le systeme de recuperation du gaz d'evaporation (boil-off)

    Energy Technology Data Exchange (ETDEWEB)

    Lanzi, D.; Vareschi, G. [SNAM S.p.A. (Italy); Sguera, O. [Snamprogetti S.p.A. (Italy)

    2000-07-01

    The Panigaglia LNG re-gasification terminal is equipped with a system recovering the boil-off gas produced during both the unloading and the re-gasification phases. The system consists of a compression station and an absorption column that condenses the boil-off by means of two packing bodies, made of INTALOX METAL ring-type, DN 1'' or 2'', depending on the quantity of boil-off available. The above configuration, which was built during the 1991 terminal revamping, was designed to optimise the previous plant facilities and compression works by compressing the boil-off up to 30 bar. At present, to reduce the operating costs deriving from the electric power consumption due to compression of the gas to high pressures, the possibility of running the column at a pressure less than 25 bar has been evaluated. A new processing solution has been studied. This configuration permits using the LNG coming from the low-pressure pumps and therefore an LNG temperature of 15 deg. C less than the one used in the original system. The maximum boil-off rate that can be absorbed has been calculated at different operating pressures. The thermodynamic (material and energy balance) behaviour of the column has been checked and the thermodynamic studies and statistical analysis have given satisfactory and consistent results. In parallel, the operating parameters referred to a period of about one year, during both the unloading and the operating phases, have been identified and analysed. (authors)

  19. An Investigation of Graduate Scientists' Understandings of Evaporation and Boiling.

    Science.gov (United States)

    Goodwin, Alan; Orlik, Yuri

    2000-01-01

    Uses a video presentation of six situations relating to the evaporation and boiling of liquids and the escape of dissolved gases from solution and investigates graduate scientists' understanding of the concepts of boiling and evaporation. (Author/YDS)

  20. The Separation of Trace Substance With High Boiling Point and Refractory Volatility From Liquor%白酒中微量高沸点难挥发性物质的分离

    Institute of Scientific and Technical Information of China (English)

    戴惠东; 张良均; 黎金霞

    2013-01-01

      采用复合溶剂间歇萃取精馏提取白酒中的微量高沸点难挥发性物质(主要是邻苯二甲酸二丁酯(DBP)和邻苯二甲酸二异丁酯(DIBP)),并同时考察溶剂种类、溶剂流率和回流比对分离效果的影响。实验结果表明:复合溶剂的最佳配比为7∶3(正戊烷与无水乙醚质量比);随着溶剂流率与回流比的增大,复合溶剂分离效果增强;在最佳配比下,当回流比为2、溶剂流率为13mL/min 时,塔釜中邻苯二甲酸二丁酯和邻苯二甲酸二异丁酯的质量分数可达95.56%。%The trace substances with high boiling point and refractory volatility in liquor (mainly are Dibutyl phthalate, DBP and Diisobutyl phthalate, DIBP) were extracted by batch extractive distillation with mixed solvent, at the same time the effect of different types of solvent, solvent flow rate and reflux ratio on separation efficiency was investigated. The results shows that the best proportion of n-pentane to diethyletheranhydrous is 7∶3, and the separation effect is improved with the increasing of solvent rate and reflux ratio, and under the conditions that the optimum value of solvent m (n-pentane):m (diethyletheranhydrous)=7∶3, reflux ratio is 2, and flow rate of solvent is 13mL/min, the mass fraction of DBP and DIBP in the bottom reaches 98.56%.

  1. Boiling heat transfer region with independence of the wall temperature

    Science.gov (United States)

    Mühlenbruch, G. H. D.; Schmidt, J.

    Extensive measurements of the intensive cooling of hot-rolled wires with temperatures between 1000 °C and 1100 °C are analysed. The analysis proves the existence of a convection-controlled boiling region, which has been previously observed by few authors in the case of high mass fluxes and high liquid subcooling. This region is characterised by an independence of the heat flux of the surface temperature. The heat flux depends essentially on the Reynolds number, the main influence parameter of the single phase convection, and on the liquid subcooling.

  2. Experimental and theoretical study on rapid transient nucleated boiling

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A laser heater has been used to impose a pulsed high power laser beam on a metal film inunersed in liquid to generate a very high rate of temperature rise up to 9.3 × 106K/s in the metal film. The rapid transient boiling phenomena have been observed and the temperature variations in the metal film have been measured. Theoretical calculations have been carried out with the fluctuation nucleation theory and the heat conduction theory to compare with the experimental results, and some results are reported.

  3. FLUIDIZED BED STEAM REFORMING ENABLING ORGANIC HIGH LEVEL WASTE DISPOSAL

    Energy Technology Data Exchange (ETDEWEB)

    Williams, M

    2008-05-09

    Waste streams planned for generation by the Global Nuclear Energy Partnership (GNEP) and existing radioactive High Level Waste (HLW) streams containing organic compounds such as the Tank 48H waste stream at Savannah River Site have completed simulant and radioactive testing, respectfully, by Savannah River National Laboratory (SRNL). GNEP waste streams will include up to 53 wt% organic compounds and nitrates up to 56 wt%. Decomposition of high nitrate streams requires reducing conditions, e.g. provided by organic additives such as sugar or coal, to reduce NOX in the off-gas to N2 to meet Clean Air Act (CAA) standards during processing. Thus, organics will be present during the waste form stabilization process regardless of the GNEP processes utilized and exists in some of the high level radioactive waste tanks at Savannah River Site and Hanford Tank Farms, e.g. organics in the feed or organics used for nitrate destruction. Waste streams containing high organic concentrations cannot be stabilized with the existing HLW Best Developed Available Technology (BDAT) which is HLW vitrification (HLVIT) unless the organics are removed by pretreatment. The alternative waste stabilization pretreatment process of Fluidized Bed Steam Reforming (FBSR) operates at moderate temperatures (650-750 C) compared to vitrification (1150-1300 C). The FBSR process has been demonstrated on GNEP simulated waste and radioactive waste containing high organics from Tank 48H to convert organics to CAA compliant gases, create no secondary liquid waste streams and create a stable mineral waste form.

  4. High Critical Current in Metal Organic Derived YBCO Films

    Science.gov (United States)

    2010-10-31

    Contract No. FA9550-07-C-0034 “High Critical Current in Metal Organic Derived YBCO Films” Final Report Prepared for: Dr. Harold...Critical Current in Metal Organic Derived YBCO Films 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT...Project focused on optimization of the Metal Organic Deposition (MOD) process for deposition thick, high critical current YBCO films for use in the

  5. Bubble Behavior in Nucleate Boiling Experiment Aboard the Space Shuttle

    OpenAIRE

    Koeln, Justin P.; Boulware, Jeffrey C.; Ban, Heng

    2009-01-01

    Boiling dynamics in microgravity need to be better understood before heat transfer systems based on boiling mechanism can be developed for space applications. This paper presents the results of a nucleate boiling experiment aboard Space Shuttle Endeavor (STS- 108). The experiment utilized nickel-chromium resistance wire to boil water in microgravity, and the data was recorded with a CCD camera and six thermistors. This data was analyzed to determine the behavior of bubble formation, detachmen...

  6. Heat transfer coefficient for boiling carbon dioxide

    DEFF Research Database (Denmark)

    Knudsen, Hans Jørgen Høgaard; Jensen, Per Henrik

    1998-01-01

    Heat transfer coefficient and pressure drop for boiling carbon dioxide (R744) flowing in a horizontal pipe has been measured. The calculated heat transfer coeeficient has been compared with the Chart correlation of Shah. The Chart Correlation predits too low heat transfer coefficient but the ratio...

  7. Heat transfer coeffcient for boiling carbon dioxide

    DEFF Research Database (Denmark)

    Knudsen, Hans Jørgen Høgaard; Jensen, Per Henrik

    1997-01-01

    Heat transfer coefficient and pressure drop for boiling carbon dioxide (R744) flowing in a horizontal pipe has been measured. The pipe is heated by condensing R22 outside the pipe. The heat input is supplied by an electrical heater wich evaporates the R22. With the heat flux assumed constant over...

  8. Big Bubbles in Boiling Liquids: Students' Views

    Science.gov (United States)

    Costu, Bayram

    2008-01-01

    The aim of this study was to elicit students' conceptions about big bubbles in boiling liquids (water, ethanol and aqueous CuSO[subscript 4] solution). The study is based on twenty-four students at different ages and grades. The clinical interviews technique was conducted to solicit students' conceptions and the interviews were analyzed to…

  9. Contact Angle Effects in Boiling Heat Transfer

    OpenAIRE

    Urquiola, Erwin; Fujita, Yasunobu

    2002-01-01

    This paper reports boiling experiments with pure water and surfactant solutions of SDS on horizontal heating surface. The static contact angle, rather than the surface tension value, was found to be the leading factor for the results and probably its prev

  10. Natural saltwater upconing by boils: field measurements and numerical modeling

    NARCIS (Netherlands)

    De Louw, Perry G.B.; Vandenbohede, A.; Oude Essink, Gualbert; Werner, Adrian D.

    2013-01-01

    Natural saltwater upconing caused by the preferential groundwater discharge of boils is a key proce ss in the salinization of Dutch deep polders. The factors controlling upconing by boil discharge and boil water salinities are poorly constrained and have not been previously documented. We addressed

  11. Nematodes: Model Organisms in High School Biology

    Science.gov (United States)

    Bliss, TJ; Anderson, Margery; Dillman, Adler; Yourick, Debra; Jett, Marti; Adams, Byron J.; Russell, RevaBeth

    2007-01-01

    In a collaborative effort between university researchers and high school science teachers, an inquiry-based laboratory module was designed using two species of insecticidal nematodes to help students apply scientific inquiry and elements of thoughtful experimental design. The learning experience and model are described in this article. (Contains 4…

  12. Teamwork as an Essential Component of High-Reliability Organizations

    OpenAIRE

    Baker, David P; Day, Rachel; Salas, Eduardo

    2006-01-01

    Organizations are increasingly becoming dynamic and unstable. This evolution has given rise to greater reliance on teams and increased complexity in terms of team composition, skills required, and degree of risk involved. High-reliability organizations (HROs) are those that exist in such hazardous environments where the consequences of errors are high, but the occurrence of error is extremely low. In this article, we argue that teamwork is an essential component of achieving high reliability ...

  13. Raw milk from vending machines: Effects of boiling, microwave treatment, and refrigeration on microbiological quality.

    Science.gov (United States)

    Tremonte, Patrizio; Tipaldi, Luca; Succi, Mariantonietta; Pannella, Gianfranco; Falasca, Luisa; Capilongo, Valeria; Coppola, Raffaele; Sorrentino, Elena

    2014-01-01

    In Italy, the sale of raw milk from vending machines has been allowed since 2004. Boiling treatment before its use is mandatory for the consumer, because the raw milk could be an important source of foodborne pathogens. This study fits into this context with the aim to evaluate the microbiological quality of 30 raw milk samples periodically collected (March 2013 to July 2013) from 3 vending machines located in Molise, a region of southern Italy. Milk samples were stored for 72 h at 4 °C and then subjected to different treatments, such as boiling and microwaving, to simulate domestic handling. The results show that all the raw milk samples examined immediately after their collection were affected by high microbial loads, with values very close to or even greater than those acceptable by Italian law. The microbial populations increased during refrigeration, reaching after 72 h values of about 8.0 log cfu/mL for Pseudomonas spp., 6.5 log cfu/mL for yeasts, and up to 4.0 log cfu/mL for Enterobacteriaceae. Boiling treatment, applied after 72 h to refrigerated milk samples, caused complete decontamination, but negatively affected the nutritional quality of the milk, as demonstrated by a drastic reduction of whey proteins. The microwave treatment at 900 W for 75 s produced microbiological decontamination similar to that of boiling, preserving the content in whey proteins of milk. The microbiological characteristics of raw milk observed in this study fully justify the obligation to boil the raw milk from vending machines before consumption. However, this study also showed that domestic boiling causes a drastic reduction in the nutritional value of milk. Microwave treatment could represent a good alternative to boiling, on the condition that the process variables are standardized for safe domestic application. Copyright © 2014 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  14. Correlation of pool boiling curves for the homogeous group freons

    Energy Technology Data Exchange (ETDEWEB)

    Westwater, J.W. (Dept. of Chemical Engineering, Univ. of Illnois, Urban, IL (US)); Zinn, J.C. (Monsanto, Co., St. Louis, MO (US)); Brodbeck, K.J. (Clorox Corp., Pleasanton, CA (US))

    1989-02-01

    A knowledge of the complete boiling curve q verses {Delta}T for a liquid, including the regimes of nucleate boiling, transition boiling, and a film boiling is needed for the design and operation of various types of heat transfer equipment. No general method exists for predicting the complete curve. Most difficult is the prediction of the nucleate boiling curve, the transition curve, and the temperature that separates the two. If the curve for every liquid at every pressure must be determined experimentally, we are faced with a formidable task. This paper shows that some simplification is possible for members of a homologous group.

  15. Microbiological Effectiveness of Disinfecting Water by Boiling in Rural Guatemala

    Science.gov (United States)

    Rosa, Ghislaine; Miller, Laura; Clasen, Thomas

    2010-01-01

    Boiling is the most common means of treating water in the home and the benchmark against which alternative point-of-use water treatment options must be compared. In a 5-week study in rural Guatemala among 45 households who claimed they always or almost always boiled their drinking water, boiling was associated with a 86.2% reduction in geometric mean thermotolerant coliforms (TTC) (N = 206, P boiling significantly improved the microbiological quality of drinking water, though boiled and stored drinking water is not always free of fecal contaminations. PMID:20207876

  16. Flow boiling in microgap channels experiment, visualization and analysis

    CERN Document Server

    Alam, Tamanna; Jin, Li-Wen

    2013-01-01

    Flow Boiling in Microgap Channels: Experiment, Visualization and Analysis presents an up-to-date summary of the details of the confined to unconfined flow boiling transition criteria, flow boiling heat transfer and pressure drop characteristics, instability characteristics, two phase flow pattern and flow regime map and the parametric study of microgap dimension. Advantages of flow boiling in microgaps over microchannels are also highlighted. The objective of this Brief is to obtain a better fundamental understanding of the flow boiling processes, compare the performance between microgap and c

  17. Interface Design Principles for High-Performance Organic Semiconductor Devices.

    Science.gov (United States)

    Nie, Wanyi; Gupta, Gautam; Crone, Brian K; Liu, Feilong; Smith, Darryl L; Ruden, P Paul; Kuo, Cheng-Yu; Tsai, Hsinhan; Wang, Hsing-Lin; Li, Hao; Tretiak, Sergei; Mohite, Aditya D

    2015-06-01

    Precise manipulation of organic donor-acceptor interfaces using spacer layers is demonstrated to suppress interface recombination in an organic photo-voltaic device. These strategies lead to a dramatic improvement in a model bilayer system and bulk-heterojunction system. These interface strategies are applicable to a wide variety of donor-acceptor systems, making them both fundamentally interesting and technologically relevant for achieving high efficiency organic electronic devices.

  18. Effect of Uniformly and Nonuniformly Coated Al2O3 Nanoparticles over Glass Tube Heater on Pool Boiling

    Directory of Open Access Journals (Sweden)

    Nitin Doifode

    2016-01-01

    Full Text Available Effect of uniformly and nonuniformly coated Al2O3 nanoparticles over plain glass tube heater on pool boiling heat transfer was studied experimentally. A borosilicate glass tube coated with Al2O3 nanoparticle was used as test heater. The boiling behaviour was studied by using high speed camera. Result obtained for pool boiling shows enhancement in heat transfer for nanoparticle coated surface heater and compared with plain glass tube heater. Also heat transfer coefficient for nonuniformly coated nanoparticles was studied and compared with uniformly coated and plain glass tube. Coating effect of nanoparticles over glass tube increases its surface roughness and thereby creates more nucleation sites.

  19. Cork boiling wastewater treatment and reuse through combination of advanced oxidation technologies.

    Science.gov (United States)

    Ponce-Robles, L; Miralles-Cuevas, S; Oller, I; Agüera, A; Trinidad-Lozano, M J; Yuste, F J; Malato, S

    2017-03-01

    Industrial preparation of cork consists of its immersion for approximately 1 hour in boiling water. The use of herbicides and pesticides in oak tree forests leads to absorption of these compounds by cork; thus, after boiling process, they are present in wastewater. Cork boiling wastewater shows low biodegradability and high acute toxicity involving partial inhibition of their biodegradation when conventional biological treatment is applied. In this work, a treatment line strategy based on the combination of advanced physicochemical technologies is proposed. The final objective is the reuse of wastewater in the cork boiling process; thus, reducing consumption of fresh water in the industrial process itself. Coagulation pre-treatment with 0.5 g/L of FeCl3 attained the highest turbidity elimination (86 %) and 29 % of DOC elimination. Similar DOC removal was attained when using 1 g/L of ECOTAN BIO (selected for ozonation tests), accompanied of 64 % of turbidity removal. Ozonation treatments showed less efficiency in the complete oxidation of cork boiling wastewater, compared to solar photo-Fenton process, under the studied conditions. Nanofiltration system was successfully employed as a final purification step with the aim of obtaining a high-quality reusable permeate stream. Monitoring of unknown compounds by LC-QTOF-MS allowed the qualitative evaluation of the whole process. Acute and chronic toxicity as well as biodegradability assays were performed throughout the whole proposed treatment line.

  20. Thermohydrodynamics of boiling in a van der Waals fluid.

    Science.gov (United States)

    Laurila, T; Carlson, A; Do-Quang, M; Ala-Nissila, T; Amberg, G

    2012-02-01

    We present a modeling approach that enables numerical simulations of a boiling Van der Waals fluid based on the diffuse interface description. A boundary condition is implemented that allows in and out flux of mass at constant external pressure. In addition, a boundary condition for controlled wetting properties of the boiling surface is also proposed. We present isothermal verification cases for each element of our modeling approach. By using these two boundary conditions we are able to numerically access a system that contains the essential physics of the boiling process at microscopic scales. Evolution of bubbles under film boiling and nucleate boiling conditions are observed by varying boiling surface wettability. We observe flow patters around the three-phase contact line where the phase change is greatest. For a hydrophilic boiling surface, a complex flow pattern consistent with vapor recoil theory is observed.

  1. Experimental investigation on the phenomena around the onset nucleate boiling during the impacting of a droplet on the hot surface

    Science.gov (United States)

    Mitrakusuma, Windy H.; Deendarlianto, Kamal, Samsul; Indarto, Nuriyadi, M.

    2016-06-01

    Onset of nucleate boiling of a droplet when impacted onto hot surface was investigated. Three kinds of surfaces, normal stainless steel (NSS), stainless steel with TiO2 coating (UVN), and stainless steel with TiO2 coating and radiated by ultraviolet ray were employed to examine the effect of wettability. The droplet size was 2.4 mm diameter, and dropped under different We number. The image is generated by high speed camera with the frame speed of 1000 fps. The boiling conditions are identified as natural convection, nucleate boiling, critical heat flux, transition, and film boiling. In the present report, the discussion will be focused on the beginning of nucleate boiling on the droplet. Nucleate boiling occurs when bubbles are generated. These bubbles are probably caused by nucleation on the impurities within the liquid rather than at nucleation sites on the heated surface because the bubbles appear to be in the bulk of the liquid instead of at the liquid-solid interface. In addition, the smaller the contact angle, the fastest the boiling.

  2. High mobility high efficiency organic films based on pure organic materials

    Science.gov (United States)

    Salzman, Rhonda F.; Forrest, Stephen R.

    2009-01-27

    A method of purifying small molecule organic material, performed as a series of operations beginning with a first sample of the organic small molecule material. The first step is to purify the organic small molecule material by thermal gradient sublimation. The second step is to test the purity of at least one sample from the purified organic small molecule material by spectroscopy. The third step is to repeat the first through third steps on the purified small molecule material if the spectroscopic testing reveals any peaks exceeding a threshold percentage of a magnitude of a characteristic peak of a target organic small molecule. The steps are performed at least twice. The threshold percentage is at most 10%. Preferably the threshold percentage is 5% and more preferably 2%. The threshold percentage may be selected based on the spectra of past samples that achieved target performance characteristics in finished devices.

  3. Characterization of SP1, a Stress-Responsive, Boiling-Soluble, Homo-Oligomeric Protein from Aspen1

    Science.gov (United States)

    Wang, Wang-Xia; Pelah, Dan; Alergand, Tal; Shoseyov, Oded; Altman, Arie

    2002-01-01

    sp1 cDNA was isolated from aspen (Populus tremula) plants by immunoscreening an expression library using polyclonal antibodies against BspA protein. BspA, which is a boiling-stable protein, accumulates in aspen plants in response to water stress and abscisic acid application (Pelah et al., 1995). The sp1 cDNA was found to encode a 12.4-kD generally hydrophilic protein with a hydrophobic C terminus, which is different from the BspA protein and was termed SP1 (stable protein 1). Northern-blot analysis revealed that sp1 encodes a small mRNA (about 0.6 kb) that is expressed in aspen plants under non-stress conditions and is accumulated after salt, cold, heat, and desiccation stress, and during the recovery from stress. The SP1 detected in plants remained soluble upon boiling, migrated both as a 12.4-kD band and a much higher mass of 116 kD on a 17% (w/v) Tricine-sodium dodecyl sulfate-polyacrylamide gel. Comparative protease digestion patterns, amino acid analyses, and the N-terminal sequences of the 12.4- and 116-kD proteins revealed that SP1 is homo-oligomeric. Furthermore, gel filtration chromatography analysis indicated that SP1 exists in aspen plants as a complex, composed of 12 subunits of 12.4 kD. A large number of sequences deduced from expressed sequence tags and genomic sequences of other organisms with unknown function show high homology to SP1. Thus, SP1 may represent a new protein family. Here, we present the first report on this putative protein family: the cloning, isolation, and characterization of SP1, a stress-responsive, boiling-soluble, oligomeric protein. PMID:12376651

  4. Organic light-emitting diodes: High-throughput virtual screening

    Science.gov (United States)

    Hirata, Shuzo; Shizu, Katsuyuki

    2016-10-01

    Computer networks, trained with data from delayed-fluorescence materials that have been successfully used in organic light-emitting diodes, facilitate the high-speed prediction of good emitters for display and lighting applications.

  5. Boiling Heat Transfer in Circulating Fluidized Beds

    Institute of Scientific and Technical Information of China (English)

    张利斌; 李修伦

    2001-01-01

    A model is proposed to predict boiling heat transfer coefficient in a three-phase circulating fluidized bed (CFB), which is a new type of evaporation boiling means for enhancing heat transfer and preventing fouling. To verify the model, experiments are conducted in a stainless steel column with 39 mm ID and 2.0 m height, in which the heat transfer coefficient is measured for different superficial velocities, steam pressures, particle concentrations and materials of particle. As the steam pressure and particle concentrations increase, the heat transfer coefficient in the bed increases. The heat transfer coefficient increases with the liquid velocity but it exhibits a local minimum.The heat transfer coefficient is correlated with cluster renewed model and two-mechanism method. The prediction of the model is in good agreement with experimental data.

  6. Boiling Heat Transfer in Circulating Fluidized Beds

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A model is proposed to predict boiling heat transfer coefficient in a three-phase circulating fluidized bed (CFB), which is a new type of evaporation boiling means for enhancing heat transfer and preventing fouling. To verify the model, experiments are conducted in a stainless steel column with 39mm ID and 2.0m height, in which the heat transfer coefficient is measured for different superficial velocities, steam pressures, particle concentrations and materials of particle. As the steam pressure and particle concentrations increase, the heat transfer coefficient in the bed increases. The heat transfer coefficient increases with the liquid velocity but it exhibits a local minimum. The heat transfer coefficient is correlated with cluster renewed model and two-mechanism method. The prediction of the model is in good agreement with experimental data.

  7. Dynamic Bubble Behaviour during Microscale Subcooled Boiling

    Institute of Scientific and Technical Information of China (English)

    WANG Hao; PENG Xiao-Feng; David M.Christopher

    2005-01-01

    @@ Bubble cycles, including initiation, growth and departure, are the physical basis of nucleate boiling. The presentinvestigation, however, reveals unusual bubble motions during subcooled nucleate boiling on microwires 25 orl00μm in diameter. Two types of bubble motions, bubble sweeping and bubble return, are observed in theexperiments. Bubble sweeping describes a bubble moving back and forth along the wire, which is motion parallelto the wire. Bubble return is the bubble moving back to the wire after it has detached or leaping above thewire. Theoretical analyses and numerical simulations are conducted to investigate the driving mechanisms forboth bubble sweeping and return. Marangoni flow from warm to cool regions along the bubble interface is foundto produce the shear stresses needed to drive these unusual bubble movements.

  8. Pool Boiling Heat Transfer on structured Surfaces

    Science.gov (United States)

    Addy, J.; Olbricht, M.; Müller, B.; Luke, A.

    2016-09-01

    The development in the process and energy sector shows the importance of efficient utilization of available resources to improve thermal devices. To achieve this goal, all thermal components have to be optimized continuously. Various applications of multi-phase heat and mass transfer have to be improved. Therefore, the heat transfer and the influence of surface roughness in nucleate boiling with the working fluid propane is experimentally investigated on structured mild steel tubes, because only few data are available in the literature. The mild steel tube is sandblasted to obtain different surface roughness. The measurements are carried out over wide ranges of heat flux and pressure. The experimental results are compared with correlations from literature and the effect of surface roughness on the heat transfer is discussed. It is shown that the heat transfer coefficient increases with increasing surface roughness, heat flux and reduced pressure at nucleate pool boiling.

  9. Self-propelled film-boiling liquids

    OpenAIRE

    Linke, H.; Aleman, B. J.; Melling, L. D.; Taormina, M. J.; Francis, M J; Dow-Hygelund, C. C.; Narayanan, V.; Taylor, R. P.; Stout, A.

    2005-01-01

    We report that liquids perform self-propelled motion when they are placed in contact with hot surfaces with asymmetric (ratchet-like) topology. The pumping effect is observed when the liquid is in the film-boiling regime, for many liquids and over a wide temperature range. We propose that liquid motion is driven by a viscous force exerted by vapor flow between the solid and the liquid.

  10. Design, Construction, and Qualification of a Microscale Heater Array for Use in Boiling Heat Transfer

    Science.gov (United States)

    Rule, T. D.; Kim, J.; Kalkur, T. S.

    1998-01-01

    Boiling heat transfer is an efficient means of heat transfer because a large amount of heat can be removed from a surface using a relatively small temperature difference between the surface and the bulk liquid. However, the mechanisms that govern boiling heat transfer are not well understood. Measurements of wall temperature and heat flux near the wall would add to the database of knowledge which is necessary to understand the mechanisms of nucleate boiling. A heater array has been developed which contains 96 heater elements within a 2.5 mm square area. The temperature of each heater element is held constant by an electronic control system similar to a hot-wire anemometer. The voltage that is being applied to each heater element can be measured and digitized using a high-speed A/D converter, and this digital information can be compiled into a series of heat-flux maps. Information for up to 10,000 heat flux maps can be obtained each second. The heater control system, the A/D system and the heater array construction are described in detail. Results are presented which show that this is an effective method of measuring the local heat flux during nucleate and transition boiling. Heat flux maps are obtained for pool boiling in FC-72 on a horizontal surface. Local heat flux variations are shown to be three to six times larger than variations in the spatially averaged heat flux.

  11. Prediction of subcooled flow boiling characteristics using two-fluid Eulerian CFD model

    Energy Technology Data Exchange (ETDEWEB)

    Braz Filho, Francisco A.; Ribeiro, Guilherme B., E-mail: gbribeiro@ieav.cta.br; Caldeira, Alexandre D.

    2016-11-15

    Highlights: • CFD multiphase model is used to predict subcooled flow boiling characteristics. • Better agreement is achieved for higher saturation pressures. • Onset of nucleate boiling and saturated boiling are well predicted. • CFD multiphase model tends to underestimate the void fraction. • Factors were adjusted in order to improve the void fraction results. - Abstract: The present study concerns a detailed analysis of flow boiling phenomena under high pressure systems using a two-fluid Eulerian approach provided by a Computational Fluid Dynamics (CFD) solver. For this purpose, a vertical heated pipe made of stainless steel with an internal diameter of 15.4 mm was considered as the modeled domain. Two different uniform heat fluxes and three saturation pressures were applied to the channel wall, whereas water mass flux of 900 kg/m{sup 2} s was considered for all simulation cases. The model was validated against a set of experimental data and results have indicated a promising use of the CFD technique for estimation of the wall temperature, the liquid bulk temperature and the location of the departure of nucleate boiling. Changes in factors applied in the modeling of the interfacial heat transfer coefficient and bubble departure frequency were suggested, allowing a better prediction of the void fraction along the heated channel. The commercial CFD solver FLUENT 14.5 was used for the model implementation.

  12. Boiling heat transfer of nanofluids--special emphasis on critical heat flux.

    Science.gov (United States)

    Kim, Sung Joong; Kim, Hyungdae

    2013-11-01

    As innovative nanotechnology-based heat-transfer media, nanofluids have evoked considerable interest among researchers owing to their improved thermal properties as well as their extendable applications to various high-power thermal systems. This paper presents a comprehensive review of recent research developments and patents pertaining to nanofluid boiling heat transfer. Nanofluids definitely offer a wide range of potential improvements in boiling heat-transfer performance. However, experimental data available from different studies are currently beset by numerous contradictions, suggesting that the fundamental mechanisms of nanofluid boiling heat transfer are not yet well understood. Consequently application of these technologies has been limited in some aspects. Only a small number of patents related to nanofluid boiling heat transfer have thus far been reported in the literature. Based on the present review, future technological development and research requirements in this area are outlined in line with technical challenges. To utilize nanofluid boiling heat-transfer technologies for practical applications, more systematic and fundamental studies are required to understand the physical mechanisms involved.

  13. Early Onset of Nucleate Boiling on Gas-covered Biphilic Surfaces.

    Science.gov (United States)

    Shen, Biao; Yamada, Masayuki; Hidaka, Sumitomo; Liu, Jiewei; Shiomi, Junichiro; Amberg, Gustav; Do-Quang, Minh; Kohno, Masamichi; Takahashi, Koji; Takata, Yasuyuki

    2017-05-17

    For phase-change cooling schemes for electronics, quick activation of nucleate boiling helps safeguard the electronics components from thermal shocks associated with undesired surface superheating at boiling incipience, which is of great importance to the long-term system stability and reliability. Previous experimental studies show that bubble nucleation can occur surprisingly early on mixed-wettability surfaces. In this paper, we report unambiguous evidence that such unusual bubble generation at extremely low temperatures-even below the boiling point-is induced by a significant presence of incondensable gas retained by the hydrophobic surface, which exhibits exceptional stability even surviving extensive boiling deaeration. By means of high-speed imaging, it is revealed that the consequently gassy boiling leads to unique bubble behaviour that stands in sharp contrast with that of pure vapour bubbles. Such findings agree qualitatively well with numerical simulations based on a diffuse-interface method. Moreover, the simulations further demonstrate strong thermocapillary flows accompanying growing bubbles with considerable gas contents, which is associated with heat transfer enhancement on the biphilic surface in the low-superheat region.

  14. Biotransformation of Organic Waste into High Quality Fertilizer

    DEFF Research Database (Denmark)

    Bryndum, Sofie

    there is a potential to increased nutrient recycling by reducing nutrient losses through improved management of the organic waste already designated as fertilizers and (2) composting has the potential to transform plant-derived organic waste into high-quality fertilizers if nutrient rich materials are added. Delaying......Agriculture faces several challenges of future provision of nutrients such as limited P reserves and increasing prices of synthetic fertilizers and recycling of nutrients from organic waste can be an important strategy for the long-term sustainability of the agricultural systems. Organically...... and S, is often low; and (3) the unbalanced composition of nutrients rarely matches crop demands. Therefore the objective of this project was to investigate the potential for (1) recycling nutrients from agro-industrial wastes and (2) compost biotransformation into high-quality organic fertilizers...

  15. Steady State Vapor Bubble in Pool Boiling

    Science.gov (United States)

    Zou, An; Chanana, Ashish; Agrawal, Amit; Wayner, Peter C.; Maroo, Shalabh C.

    2016-02-01

    Boiling, a dynamic and multiscale process, has been studied for several decades; however, a comprehensive understanding of the process is still lacking. The bubble ebullition cycle, which occurs over millisecond time-span, makes it extremely challenging to study near-surface interfacial characteristics of a single bubble. Here, we create a steady-state vapor bubble that can remain stable for hours in a pool of sub-cooled water using a femtosecond laser source. The stability of the bubble allows us to measure the contact-angle and perform in-situ imaging of the contact-line region and the microlayer, on hydrophilic and hydrophobic surfaces and in both degassed and regular (with dissolved air) water. The early growth stage of vapor bubble in degassed water shows a completely wetted bubble base with the microlayer, and the bubble does not depart from the surface due to reduced liquid pressure in the microlayer. Using experimental data and numerical simulations, we obtain permissible range of maximum heat transfer coefficient possible in nucleate boiling and the width of the evaporating layer in the contact-line region. This technique of creating and measuring fundamental characteristics of a stable vapor bubble will facilitate rational design of nanostructures for boiling enhancement and advance thermal management in electronics.

  16. Flow boiling test of GDP replacement coolants

    Energy Technology Data Exchange (ETDEWEB)

    Park, S.H. [comp.

    1995-08-01

    The tests were part of the CFC replacement program to identify and test alternate coolants to replace CFC-114 being used in the uranium enrichment plants at Paducah and Portsmouth. The coolants tested, C{sub 4}F{sub 10} and C{sub 4}F{sub 8}, were selected based on their compatibility with the uranium hexafluoride process gas and how well the boiling temperature and vapor pressure matched that of CFC-114. However, the heat of vaporization of both coolants is lower than that of CFC-114 requiring larger coolant mass flow than CFC-114 to remove the same amount of heat. The vapor pressure of these coolants is higher than CFC-114 within the cascade operational range, and each coolant can be used as a replacement coolant with some limitation at 3,300 hp operation. The results of the CFC-114/C{sub 4}F{sub 10} mixture tests show boiling heat transfer coefficient degraded to a minimum value with about 25% C{sub 4}F{sub 10} weight mixture in CFC-114 and the degree of degradation is about 20% from that of CFC-114 boiling heat transfer coefficient. This report consists of the final reports from Cudo Technologies, Ltd.

  17. Pressure drop in saturated flow boiling

    Energy Technology Data Exchange (ETDEWEB)

    Collado, Francisco J. [Universidad de Zaragoza, Zaragoza (Spain)

    2003-07-01

    A new mass balance for flow boiling have been recently suggested by the author following a quite simple idea: if the phases have different velocities, they can not cover the same distance -the control volume length for a 1-d system- in the same time. Thus, the time scales of the phases have to be different, and we should scale the time dependent magnitudes of one phase to the other one before combining them. Furthermore, it is reasonable to think that conservation equations should have to include in some manner this evident physical fact. In complete coherence with the former mass balance, a new energy balance, which does include the slip ratio has been also stated. This work, whilst reviews these new fundamentals for saturated flow boiling, stresses those aspects related with the prediction of the pressure drop in saturated flow boiling. The new correlations found for the data carefully measured by Thom during the Cambridge project would confirm the new two-phase flowapproach.

  18. Steady State Vapor Bubble in Pool Boiling.

    Science.gov (United States)

    Zou, An; Chanana, Ashish; Agrawal, Amit; Wayner, Peter C; Maroo, Shalabh C

    2016-02-03

    Boiling, a dynamic and multiscale process, has been studied for several decades; however, a comprehensive understanding of the process is still lacking. The bubble ebullition cycle, which occurs over millisecond time-span, makes it extremely challenging to study near-surface interfacial characteristics of a single bubble. Here, we create a steady-state vapor bubble that can remain stable for hours in a pool of sub-cooled water using a femtosecond laser source. The stability of the bubble allows us to measure the contact-angle and perform in-situ imaging of the contact-line region and the microlayer, on hydrophilic and hydrophobic surfaces and in both degassed and regular (with dissolved air) water. The early growth stage of vapor bubble in degassed water shows a completely wetted bubble base with the microlayer, and the bubble does not depart from the surface due to reduced liquid pressure in the microlayer. Using experimental data and numerical simulations, we obtain permissible range of maximum heat transfer coefficient possible in nucleate boiling and the width of the evaporating layer in the contact-line region. This technique of creating and measuring fundamental characteristics of a stable vapor bubble will facilitate rational design of nanostructures for boiling enhancement and advance thermal management in electronics.

  19. Evaluation of onset of nucleate boiling models

    Energy Technology Data Exchange (ETDEWEB)

    Huang, LiDong [Heat Transfer Research, Inc., College Station, TX (United States)], e-mail: lh@htri.net

    2009-07-01

    This article discusses available models and correlations for predicting the required heat flux or wall superheat for the Onset of Nucleate Boiling (ONB) on plain surfaces. It reviews ONB data in the open literature and discusses the continuing efforts of Heat Transfer Research, Inc. in this area. Our ONB database contains ten individual sources for ten test fluids and a wide range of operating conditions for different geometries, e.g., tube side and shell side flow boiling and falling film evaporation. The article also evaluates literature models and correlations based on the data: no single model in the open literature predicts all data well. The prediction uncertainty is especially higher in vacuum conditions. Surface roughness is another critical criterion in determining which model should be used. However, most models do not directly account for surface roughness, and most investigators do not provide surface roughness information in their published findings. Additional experimental research is needed to improve confidence in predicting the required wall superheats for nucleation boiling for engineering design purposes. (author)

  20. Experimental research on heat transfer to liquid sodium and its incipient boiling wall superheat in an annulus

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Liquid sodium is mainly used as a cooling fluid in the liquid metal fast breeder reactor (LMFBR), whose heat transfer, whether convective heat transfer or boiling heat transfer, is different from that of water. So it is important for both normal and accidental operations of LMFBR to perform experimental research on heat transfer to liquid sodium and its boiling heat transfer. This study deals with heat transfer with high temperature (300-700℃) and low Pe number (20~70) and heat transfer with low temperature (250~270℃) and high Pe number (125~860), and its incipient boiling wall superheat in an annulus. Research on heat transfer involves theoretical research and experiments on heat transfer to liquid sodium. It also focuses on the theoretical analysis and experimental research on its incipient boiling wall superheat at positive pressure in an annulus. Semiempirical correlations were obtained and they were well coincident with the experimental data.

  1. Effect of Low-Temperature and High-Pressure Boiling and NaCl Addition on Protein Content and Flavor Components of Bovine Bone Broth%低温高压及预先添加NaCl对牛骨汤的煮制效果及风味成分的影响

    Institute of Scientific and Technical Information of China (English)

    刘文营; 李迎楠; 成晓瑜; 贾晓云; 曲超; 李家鹏; 陈文华

    2016-01-01

    研究加压煮制对牛骨汤煮制效果的影响,并对预先添加NaCl对骨汤风味的影响进行分析。结果表明:低温高压相较于常规煮制,蛋白质溶出速率有显著提升。气质联用对风味物质进行检测结果显示:肉汤中酯类、杂环物质、酮类、烃类、酸类、醛类、芳香族化合物和醇类等均有不同程度的变化;加入NaCl煮制时肉汤中酯类、酸类、芳香族和醇类物质种类和相对含量均有不同程度的增加,杂环物质种类和相对含量较仅加压制备样品有显著下降;酮类、醛类和醇类物质种类均有不同程度的增加,但是相对含量均较对照组要小;烃类物质种类没有发生变化,但是相对含量明显增加。因此,加压煮制过程中添加NaCl,对牛骨汤中挥发性物质的种类有明显影响。%The effect of boiling under pressurized condition on the protein content of bovine bone broth was investigated as well as the effect of NaCl addition during boiling on its lfavor components. The dissolution rate of protein was signiifcantly accelerated under low-temperature and high-pressure conditions compared with the conventional boiling method. The esters, heterocyclic compounds, hydrocarbons, ketones, acids, aldehydes, aromatic compounds and alcohols in the broth changed to different extents as detected by GC-MS. The composition and relative contents of esters, acids, aromatic compounds and alcohols were increased upon NaCl addition during boiling, while those of heterocyclic compounds in the sample boiled under pressurized condition without NaCl addition were signiifcantly reduced. In addition, the numbers of ketones, aldehydes and alcohols were increased, but their relative contents were lower than in the control group. The composition of hydrocarbons did not change although their relative contents were signiifcantly enhanced. Thus, NaCl addition during boiling had a signiifcant effect on the composition of

  2. Stability monitoring for boiling water reactors

    Science.gov (United States)

    Cecenas-Falcon, Miguel

    1999-11-01

    A methodology is presented to evaluate the stability properties of Boiling Water Reactors based on a reduced order model, power measurements, and a non-linear estimation technique. For a Boiling Water Reactor, the feedback reactivity imposed by the thermal-hydraulics has an important effect in the system stability, where the dominant contribution to this feedback reactivity is provided by the void reactivity. The feedback reactivity is a function of the operating conditions of the system, and cannot be directly measured. However, power measurements are relatively easy to obtain from the nuclear instrumentation and process computer, and are used in conjunction with a reduced order model to estimate the gain of the thermal-hydraulics feedback using an Extended Kalman Filter. The reduced order model is obtained by estimating the thermal-hydraulic transfer function from the frequency-domain BWR code LAPUR, and the stability properties are evaluated based on the pair of complex conjugate eigenvalues. Because of the recursive nature of the Kalman Filter, an estimate of the decay ratio is generated every sampling time, allowing continuous estimation of the stability parameters. A test platform based on a nuclear-coupled boiling channel is developed to validate the capability of the BWR stability monitoring methodology. The thermal-hydraulics for the boiling channel is modeled and coupled with neutron kinetics to analyze the non-linear dynamics of the closed-loop system. The model uses point kinetics to study core-wide oscillations, and normalized modal kinetics are introduced to study out-of-phase oscillations. The coolant flow dynamics is dominant in the power fluctuations observed by in-core nuclear instrumentation, and additive white noise is added to the solution for the channel flow in the thermal-hydraulic model to generate noisy power time series. The operating conditions of the channel can be modified to accommodate a wide range of stability conditions

  3. Experimental study about ONB and subcooled boiling heat transfer

    Energy Technology Data Exchange (ETDEWEB)

    Changhong, P.; Myint, A.; Yun, G.; Dounan, J. [State Key Laboratory of Multiphase Flow in power engineering, Department of Nuclear and Thermal Power Engineering, Xian (China)

    2004-07-01

    Water subcooled boiling heat transfer were experimentally investigated in the vertical annuli with narrow gap. Subcooled flow boiling covers the region from the location where the bubbles forms on the wall to the location where the bulk temperature reaches saturated temperature. Three locations in the subcooled flow boiling have been identified by earlier researchers as the onset of nucleate boiling (ONB), the beginning of fully developed boiling, and the location where the thermodynamic quality is zero that is inferred from the enthalpy balance equation. The heat transfer regions are identified as single-phase heat transfer prior to ONB, partial boiling (PB) and fully developed boiling (FDB). In this study, the available models for predicting heat transfer in the different regions and the modified correlation can predict our experimental data: -) the heat flux of ONB can be predicted by the Unal correlation, nevertheless the h{sub FC} is calculated by the modified Dittus-Boelter correlations in the narrow annuli, -) Griffith's method can be modified to identify the beginning of fully develop boiling, -) in the partial boiling region, the heat transfer coefficient can be calculated by h{sub PB} equals (1-a)*h{sub L} + a*h{sub FDB}, and -) in the fully developed region, the correlation for saturated flow boiling can be employed to describe the heat transfer.

  4. Analysis of migrants from nylon 6 packaging films into boiling water.

    Science.gov (United States)

    Barkby, C T; Lawson, G

    1993-01-01

    Ultra-violet spectrophotometry (UV), high performance liquid chromatography (HPLC) and liquid chromatography coupled to mass spectroscopy (LC-MS) were used to identify and quantify oligomers extracted with boiling water from two different nylon 6 films used in boil-in-bag food packaging. The results indicated the loss of up to 1.5% of the original nylon film weight, into the boiling water, as caprolactam and cyclic oligomers up to the nonamer. Extraction time, thickness and type of film used, were found to be parameters which affected the levels of these migrants. These results will be relevant to situations in which food is cooked in the water used to heat the pouch contents.

  5. Enhancing flow boiling heat transfer in microchannels for thermal management with monolithically-integrated silicon nanowires.

    Science.gov (United States)

    Li, D; Wu, G S; Wang, W; Wang, Y D; Liu, Dong; Zhang, D C; Chen, Y F; Peterson, G P; Yang, Ronggui

    2012-07-11

    Thermal management has become a critical issue for high heat flux electronics and energy systems. Integrated two-phase microchannel liquid-cooling technology has been envisioned as a promising solution, but with great challenges in flow instability. In this work, silicon nanowires were synthesized in situ in parallel silicon microchannel arrays for the first time to suppress the flow instability and to augment flow boiling heat transfer. Significant enhancement in flow boiling heat transfer performance was demonstrated for the nanowire-coated microchannel heat sink, such as an early onset of nucleate boiling, a delayed onset of flow oscillation, suppressed oscillating amplitudes of temperature and pressure drop, and an increased heat transfer coefficient.

  6. Impact of boiling conditions on the molecular and sensory profile of a vegetable broth.

    Science.gov (United States)

    Mougin, Alice; Mauroux, Olivier; Matthey-Doret, Walter; Barcos, Eugenia Maria; Beaud, Fernand; Bousbaine, Ahmed; Viton, Florian; Smarrito-Menozzi, Candice

    2015-02-11

    Low-pressure cooking has recently been identified as an alternative to ambient and high-pressure cooking to provide food with enhanced organoleptic properties. This work investigates the impact of the cooking process at different pressures on the molecular and sensory profile of a vegetable broth. Experimental results showed similar sensory and chemical profiles of vegetable broths when boiling at 0.93 and 1.5 bar, while an enhancement of sulfur volatile compounds correlated with a greater leek content and savory aroma was observed when boiling at low pressure (80 °C/0.48 bar). Thus, low-pressure cooking would allow preserving the most labile volatiles likely due to the lower water boiling temperature and the reduced level of oxygen. This study evidenced chemical and sensory impact of pressure during cooking and demonstrated that the flavor profile of culinary preparations can be enhanced by applying low-pressure conditions.

  7. The Effect of Different Boiling and Filtering Devices on the Concentration of Disinfection By-Products in Tap Water

    OpenAIRE

    Glòria Carrasco-Turigas; Villanueva, Cristina M.; Fernando Goñi; Panu Rantakokko; Nieuwenhuijsen, Mark J.

    2013-01-01

    Disinfection by-products (DBPs) are ubiquitous contaminants in tap drinking water with the potential to produce adverse health effects. Filtering and boiling tap water can lead to changes in the DBP concentrations and modify the exposure through ingestion. Changes in the concentration of 4 individual trihalomethanes (THM4) (chloroform (TCM), bromodichloromethane (BDCM), dibromochloromethane (DBCM), and bromoform (TBM)), MX, and bromate were tested when boiling and filtering high bromine-conta...

  8. An electrical simulator of a nuclear fuel rod cooled by nucleate boiling

    Energy Technology Data Exchange (ETDEWEB)

    Costa, Antonio Carlos Lopes da [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)], e-mail: aclc@cdtn.br; Machado, Luiz; Koury, Ricardo Nicolau Nassar [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil). Dept. de Engenharia Mecanica], e-mail: luizm@demec.ufmg.br; Bonjour, Jocelyn [CETHIL, UMR5008, CNRS, INSA-Lyon (France)], e-mail: jocelyn.bonjour@insa-lyon.fr; Passos, Julio Cesar [Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil). Dept. de Engenharia Mecanica. LEPTEN/Boiling], e-mail: jpassos@emc.ufsc.br

    2009-07-01

    This study investigates an electrical heated test section designed to simulate a nuclear fuel rod. This simulator comprises a stainless steel vertical tube, with length and outside diameter of 600 mm and 10 mm, respectively, inside which there is a high power electrical resistor. The heat generated is removed by means of enhanced confined subcooled nucleate boiling of water in an annular space containing 153 small metal inclined discs. The tests were performed under electrical power and pressure up to 48 kW and 40 bar, respectively. The results show that the experimental boiling heat transfer coefficients are in good agreement with those calculated using the Jens-Lottes correlation. (author)

  9. On the lateral fluid motion during pool boiling via preferentially located cavities

    Science.gov (United States)

    Kapsenberg, F.; Strid, L.; Thiagarajan, N.; Narayanan, V.; Bhavnani, S. H.

    2014-04-01

    Passively generated lateral motion of fluid during pool boiling on asymmetrically textured meso-scale structures is discussed in this Letter. The surface texture is in the form of 30°-60° mm-scale ratchets with re-entrant cavities located on the 30° face. High speed visualization of growing bubbles from cavities indicates growth and departure normal to the 30° face of the ratchets. A semi-empirical model of net axial liquid velocity due to the non-vertical bubble growth is developed and validated in a pool boiling experiment.

  10. Lattice Boltzmann modeling of boiling heat transfer: The boiling curve and the effects of wettability

    OpenAIRE

    Li, Q; Kang, Q. J.; Francois, M. M.; He, Y. L.; Luo, K. H.

    2015-01-01

    A hybrid thermal lattice Boltzmann (LB) model is presented to simulate thermal multiphase flows with phase change based on an improved pseudopotential LB approach [Q. Li, K. H. Luo, and X. J. Li, Phys. Rev. E 87, 053301 (2013)]. The present model does not suffer from the spurious term caused by the forcing-term effect, which was encountered in some previous thermal LB models for liquid-vapor phase change. Using the model, the liquid-vapor boiling process is simulated. The boiling curve togeth...

  11. Direct Numerical Simulation of Boiling Multiphase Flows: State-of-the-Art, Modeling, Algorithmic and Computer Needs

    Energy Technology Data Exchange (ETDEWEB)

    Nourgaliev R.; Knoll D.; Mousseau V.; Berry R.

    2007-04-01

    The state-of-the-art for Direct Numerical Simulation (DNS) of boiling multiphase flows is reviewed, focussing on potential of available computational techniques, the level of current success for their applications to model several basic flow regimes (film, pool-nucleate and wall-nucleate boiling -- FB, PNB and WNB, respectively). Then, we discuss multiphysics and multiscale nature of practical boiling flows in LWR reactors, requiring high-fidelity treatment of interfacial dynamics, phase-change, hydrodynamics, compressibility, heat transfer, and non-equilibrium thermodynamics and chemistry of liquid/vapor and fluid/solid-wall interfaces. Finally, we outline the framework for the {\\sf Fervent} code, being developed at INL for DNS of reactor-relevant boiling multiphase flows, with the purpose of gaining insight into the physics of multiphase flow regimes, and generating a basis for effective-field modeling in terms of its formulation and closure laws.

  12. Experimental Research on Flash Boiling Spray of Dimethyl Ether

    Institute of Scientific and Technical Information of China (English)

    Peng Zhang

    2014-01-01

    The high-speed digital imaging technique is applied to observe the developing process of flash boiling spray of dimethyl ether at low ambient pressure, and the effects of nozzle opening pressure and nozzle hole diameter on the spray shape, spray tip penetration and spray angle during the injection are investigated. The experimental results show that the time when the vortex ring structure of flash boiling spray forms and its developing process are determined by the combined action of the bubble growth and breakup in the spray and the air drag on the leading end of spray;with the enhancement of nozzle opening pressure, the spray tip penetration increases and the spray angle decreases. The influence of nozzle hole diameter on the spray tip penetration is relatively complicated, the spray tip penetration is longer with a smaller nozzle hole diameter at the early stage of injection, while the situation is just opposite at the later stage of injection. This paper establishes that the variation of spray angle is consistent with that of nozzle hole diameter.

  13. Experimental research on flash boiling spray of dimethyl ether

    Science.gov (United States)

    Zhang, Peng

    2014-12-01

    The high-speed digital imaging technique is applied to observe the developing process of flash boiling spray of dimethyl ether at low ambient pressure, and the effects of nozzle opening pressure and nozzle hole diameter on the spray shape, spray tip penetration and spray angle during the injection are investigated. The experimental results show that the time when the vortex ring structure of flash boiling spray forms and its developing process are determined by the combined action of the bubble growth and breakup in the spray and the air drag on the leading end of spray; with the enhancement of nozzle opening pressure, the spray tip penetration increases and the spray angle decreases. The influence of nozzle hole diameter on the spray tip penetration is relatively complicated, the spray tip penetration is longer with a smaller nozzle hole diameter at the early stage of injection, while the situation is just opposite at the later stage of injection. This paper establishes that the variation of spray angle is consistent with that of nozzle hole diameter.

  14. Effect of superheat and electric field on saturated film boiling

    Science.gov (United States)

    Pandey, Vinod; Biswas, Gautam; Dalal, Amaresh

    2016-05-01

    The objective of this investigation is to study the influence of superheat temperature and applied uniform electric field across the liquid-vapor interface during film boiling using a coupled level set and volume of fluid algorithm. The hydrodynamics of bubble growth, detachment, and its morphological variation with electrohydrodynamic forces are studied considering the medium to be incompressible, viscous, and perfectly dielectric at near critical pressure. The transition in interfacial instability behavior occurs with increase in superheat, the bubble release being periodic both in space and time. Discrete bubble growth occurs at a smaller superheat whereas vapor columns form at the higher superheat values. Destabilization of interfacial motion due to applied electric field results in decrease in bubble separation distance and increase in bubble release rate culminating in enhanced heat transfer rate. A comparison of maximum bubble height owing to application of different intensities of electric field is performed at a smaller superheat. The change in dynamics of bubble growth due to increasing superheat at a high intensity of electric field is studied. The effect of increasing intensity of electric field on the heat transfer rate at different superheats is determined. The boiling characteristic is found to be influenced significantly only above a minimum critical intensity of the electric field.

  15. Water flow boiling behaviors in hydrophilic and hydrophobic microchannels

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Chiwoong; Yu, Dongin; Kim, Moohwan [Pohang University of Science and Technology (Korea, Republic of). Dept. of Mechanical Engineering

    2009-07-01

    The wettability is one of issues on two-phase flow in a microchannel. However, previous studies of wettability effect on two-phase flow have conducted only isothermal condition. Moreover, most studies have used conventional micro/mini-tubes due to difficulties of their fabrication. The objective of our study is to understand the wettability effect on flow boiling in a rectangular microchannel. In the first, new micro-electro-mechanical-system (MEMS) fabrication technique was developed to obtain a single glass rectangular microchannel and localized six micro heaters. A photosensitive glass was used as base material. The photosensitive glass is hydrophilic, so the hydrophobic microchannel was prepared by coating SAM, flow boiling experiments were conducted in hydrophilic and hydrophobic microchannels with micro heaters. The experiment range was the mass flux of 25 and 75 kg/m{sup 2}s, the heat flux of 30 - 430 k W/m2 and quality of 0 - 0.3. A working fluid was de-ionized and degassed water. The local heat transfer coefficient was evaluated at the local micro heater section. Also, flow regimes in the microchannel were visualized by using a high-speed camera with a long-distance microscope. Heat transfer was analyzed with visualization results. Heat transfer in the hydrophobic microchannel was enhanced by higher nucleation site density and delayed local dryout. The pressure drop in the hydrophobic microchannel was higher than that in the hydrophilic microchannel. (author)

  16. A review on boiling heat transfer enhancement with nanofluids.

    Science.gov (United States)

    Barber, Jacqueline; Brutin, David; Tadrist, Lounes

    2011-04-04

    There has been increasing interest of late in nanofluid boiling and its use in heat transfer enhancement. This article covers recent advances in the last decade by researchers in both pool boiling and convective boiling applications, with nanofluids as the working fluid. The available data in the literature is reviewed in terms of enhancements, and degradations in the nucleate boiling heat transfer and critical heat flux. Conflicting data have been presented in the literature on the effect that nanofluids have on the boiling heat-transfer coefficient; however, almost all researchers have noted an enhancement in the critical heat flux during nanofluid boiling. Several researchers have observed nanoparticle deposition at the heater surface, which they have related back to the critical heat flux enhancement.

  17. Water boiling inside carbon nanotubes: toward efficient drug release.

    Science.gov (United States)

    Chaban, Vitaly V; Prezhdo, Oleg V

    2011-07-26

    We show using molecular dynamics simulation that spatial confinement of water inside carbon nanotubes (CNTs) substantially increases its boiling temperature and that a small temperature growth above the boiling point dramatically raises the inside pressure. Capillary theory successfully predicts the boiling point elevation down to 2 nm, below which large deviations between the theory and atomistic simulation take place. Water behaves qualitatively different inside narrow CNTs, exhibiting transition into an unusual phase, where pressure is gas-like and grows linearly with temperature, while the diffusion constant is temperature-independent. Precise control over boiling by CNT diameter, together with the rapid growth of inside pressure above the boiling point, suggests a novel drug delivery protocol. Polar drug molecules are packaged inside CNTs; the latter are delivered into living tissues and heated by laser. Solvent boiling facilitates drug release.

  18. Infrared thermometry study of nanofluid pool boiling phenomena

    Science.gov (United States)

    2011-01-01

    Infrared thermometry was used to obtain first-of-a-kind, time- and space-resolved data for pool boiling phenomena in water-based nanofluids with diamond and silica nanoparticles at low concentration (boiling heat transfer (by as much as 50%) and an increase in the CHF (by as much as 100%). The bubble departure frequency and NSD were found to be lower in nanofluids compared with water for the same wall superheat. Furthermore, it was found that a porous layer of nanoparticles built up on the heater surface during nucleate boiling, which improved surface wettability compared with the water-boiled surfaces. Using the prevalent nucleate boiling models, it was possible to correlate this improved surface wettability to the experimentally observed reductions in the bubble departure frequency, NSD, and ultimately to the deterioration in the nucleate boiling heat transfer and the CHF enhancement. PMID:21711754

  19. High-efficiency organic solar concentrators for photovoltaics.

    Science.gov (United States)

    Currie, Michael J; Mapel, Jonathan K; Heidel, Timothy D; Goffri, Shalom; Baldo, Marc A

    2008-07-11

    The cost of photovoltaic power can be reduced with organic solar concentrators. These are planar waveguides with a thin-film organic coating on the face and inorganic solar cells attached to the edges. Light is absorbed by the coating and reemitted into waveguide modes for collection by the solar cells. We report single- and tandem-waveguide organic solar concentrators with quantum efficiencies exceeding 50% and projected power conversion efficiencies as high as 6.8%. The exploitation of near-field energy transfer, solid-state solvation, and phosphorescence enables 10-fold increases in the power obtained from photovoltaic cells, without the need for solar tracking.

  20. New Reactions and Strategies in Highly Selective Organic Synthesis

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    @@ Organic synthetic chemistry is a core area of chemical The achievements in research.this field have greatly enhanced our life quality worldwide by providing an impressive range of useful man-made substances, materials and drugs.However, practical organic synthesis requires high selectivity, productivity, atom economy, cost efficiency, operational simplicity, environmental friendliness, and low energy consumption.It is of great importance to conduct intensive research in the development of new organic reactions, new methods and strategies, as well as the synthesis of bioactive important molecules.

  1. Metal-Organic Frameworks for Highly Selective Separations

    Energy Technology Data Exchange (ETDEWEB)

    Omar M. Yaghi

    2009-09-28

    This grant was focused on the study of metal-organic frameworks with these specific objectives. (1) To examine the use of MOFs with well-defined open metal sites for binding of gases and small organics. (2) To develop a strategy for producing MOFs that combine large pore size with high surface area for their use in gas adsorption and separation of polycyclic organic compounds. (3) To functionalize MOFs for the storage of inert gases such as methane. A brief outline of our progress towards these objectives is presented here as it forms part of the basis for the ideas to be developed under the present proposal.

  2. A study of flow boiling phenomena using real time neutron radiography

    Science.gov (United States)

    Novog, David Raymond

    The operation and safety of both fossil-fuel and nuclear power stations depend on adequate cooling of the thermal source involved. This is usually accomplished using liquid coolants that are forced through the high temperature regions by a pumping system; this fluid then transports the thermal energy to another section of the power station. However, fluids that undergo boiling during this process create vapor that can be detrimental, and influence safe operation of other system components. The behavior of this vapor, or void, as it is generated and transported through the system is critical in predicting the operational and safety performance. This study uses two advanced penetrating radiation techniques, Real Time Neutron Radiography (RTNR), and High Speed X-Ray Tomography (HS-XCT), to examine void generation and transport behavior in a flow boiling system. The geometries studied were tube side flow boiling in a cylindrical configuration, and a similar flow channel with an internal twisted tape swirl flow generator. The heat transfer performance and pressure drop characteristics were monitored in addition to void distribution measurements, so that the impact of void distribution could be determined. The RTNR and heat transfer pipe flow studies were conducted using boiling Refrigerant 134a at pressures from 500 to 700 kPa, inlet subcooling from 3 to 12°C and mass fluxes from 55 to 170kg/m 2-s with heat fluxes up to 40 kW/m2. RTNR and HS-XCT were used to measure the distribution and size of the vapor phases in the channel for cylindrical tube-side flow boiling and swirl-flow boiling geometries. The results clearly show that the averaged void is similar for both geometries, but that there is a significant difference in the void distribution, velocity and transport behavior from one configuration to the next. Specifically, the void distribution during flow boiling in a cylindrical-tube test section showed that the void fraction was largest near the tube center and

  3. Travel to High Altitude Following Solid Organ Transplantation.

    Science.gov (United States)

    Luks, Andrew M

    2016-09-01

    Luks, Andrew M. Clinician's corner: travel to high altitude following solid organ transplantation. High Alt Med Biol. 17:147-156, 2016.-As they regain active lifestyles following successful organ transplantation, transplant recipients may travel to high altitude for a variety of activities, including skiing, climbing, and trekking. This review is intended to provide information for medical providers who may encounter transplant patients seeking advice before planned high altitude travel or care for medical issues that develop during the actual sojourn. There is currently limited information in the literature about outcomes during high-altitude travel following solid organ transplantation, but the available evidence suggests that the physiologic responses to hypobaric hypoxia are comparable to those seen in nontransplanted individuals and well-selected transplant recipients with no evidence of organ rejection can tolerate ascents as high as 6200 m. All transplant recipients planning high-altitude travel should undergo pretravel assessment and counseling with an emphasis on the recognition, prevention, and treatment of altitude illness, as well as the importance of preventing infection and limiting sun exposure. Transplant recipients can use the standard medications for altitude illness prophylaxis and treatment, but the choice and dose of medication should take into account the patient's preexisting medication regimen and current renal function. With careful attention to these and other details, the healthy transplant recipient can safely experience the rewards of traveling in the mountains.

  4. Experimental investigation on the boiling heat transfer of nanofluids on a flat plate in the presence of a magnetic field

    Science.gov (United States)

    Abdollahi, Ali; Reza Salimpour, Mohammad

    2016-11-01

    In this paper, the pool boiling heat transfer of Fe3O4 -deionized (DI) water as a magnetic nanofluid has been experimentally analyzed in the atmospheric pressure. The applied nanofluid within this research has been synthesized through a single step to retain a high stability. The repeatability and precision of the testing device with deionized water show a good agreement with the equations introduced in previous studies. Parametric studies on magnetic field, surface roughness, and magnetic nanofluid concentration are performed to reveal various aspects of the boiling heat transfer. In order to study the surface roughness, two surfaces with high average roughness (480nm) and low average roughness (7.3nm) were used. The obtained results indicate that the boiling heat transfer on the rough surface increases when raising the nanofluid concentration up to 0.1% volume concentration. In addition, it is observed that there is an optimum 0.1% volume concentration for the nanofluid which makes the boiling heat transfer coefficient increase up to 43%. Moreover, the heat transfer of a nanofluid with volume concentration of 0.1% is greater for the rough surface compared with the smooth one. The results of the experiments indicate that adding nanoparticles would not necessarily increase the boiling heat transfer coefficient. In fact, the surface roughness and the magnetic field gradient on the boiling surface were the main factors that could affect the boiling heat transfer coefficient significantly. The simultaneous analysis of magnetic field, surface roughness, and nanofluid concentration reveals that the boiling heat transfer coefficient of the magnetic nanofluid with 0.1% volume concentration in the presence of a magnetic field on the rough surface is higher than on the smooth surface. Our findings show that this increase is associated to the increase of nucleation sites concentration and bubble formation sites for the rough surface.

  5. Teamwork as an essential component of high-reliability organizations.

    Science.gov (United States)

    Baker, David P; Day, Rachel; Salas, Eduardo

    2006-08-01

    Organizations are increasingly becoming dynamic and unstable. This evolution has given rise to greater reliance on teams and increased complexity in terms of team composition, skills required, and degree of risk involved. High-reliability organizations (HROs) are those that exist in such hazardous environments where the consequences of errors are high, but the occurrence of error is extremely low. In this article, we argue that teamwork is an essential component of achieving high reliability particularly in health care organizations. We describe the fundamental characteristics of teams, review strategies in team training, demonstrate the criticality of teamwork in HROs and finally, identify specific challenges the health care community must address to improve teamwork and enhance reliability.

  6. Natural convection heat transfer characteristics of the molten metal pool with solidification by boiling coolant

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Jae Seon; Suh, Kune Yull; Chung, Chang Hyun [Seoul National University, Seoul (Korea, Republic of); Paark, Rae Joon; Kim, Sang Baik [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1997-12-31

    This paper presents results of experimental studies on the heat transfer and solidification of the molten metal pool with overlying coolant with boiling. The metal pool is heated from the bottom surface and coolant is injected onto the molten metal pool. Ad a result, the crust, which is a solidified layer, may form at the top of the molten metal pool. Heat transfer is accomplished by a conjugate mechanism, which consists of the natural convection of the molten metal pool, the conduction in the crust layer and the convective boiling heat transfer in the coolant. This work examines the crust formation and the heat transfer rate on the molten metal pool with boiling coolant. The simulant molten pool material is tin (Sn) with the melting temperature of 232 deg C. Demineralized water is used as the working coolant. The crust layer thickness was ostensibly varied by the heated bottom surface temperature of the test section, but not much affected by the coolant injection rate. The correlation between the Nusselt number and the Rayleigh number in the molten metal pool region of this study is compared against the crust formation experiment without coolant boiling and the literature correlations. The present experimental results are higher than those from the experiment without coolant boiling, but show general agreement with the Eckert correlation, with some deviations in the high and low ends of the Rayleigh number. This discrepancy is currently attributed to concurrent rapid boiling of the coolant on top of the metal layer. 10 refs., 4 figs., 1 tab. (Author)

  7. To what extent do Turkish high school students know about their body organs and organ systems?

    Directory of Open Access Journals (Sweden)

    Solmaz Aydın

    2016-02-01

    Full Text Available This study aimed to determine high school students' familiarity with body organs and knowledge about the systems to which organs belong. It also identifies their misconceptions and deficiencies and discusses their causes. The sample of the study consisted of 244 secondary students. The study used the descriptive survey method. The findings show that the heart, lungs, kidneys and stomach are the best known organs by the students, and that they most often identified organs in the circulatory, respiratory, urinary and digestive systems rather than other systems. In addition, there are no considerable differences between the ninth, tenth, eleventh grade classes and the twelfth grade students’ knowledge and misconceptions about organs and organ systems. The most basic misconceptions identified in this study is that a majority of the students who identified the small intestine, liver, pancreas, anus and intestine thought that these organs were parts of the excretory system. In Turkey's educational system, students are taught the urinary system as the excretory system. This leads students to think that these organs are not elements of the digestive system, but those of the excretory system, which is used to defecate the excretions. For this reason, this study will also discuss this situation.

  8. Boiling Experiment Facility for Heat Transfer Studies in Microgravity

    Science.gov (United States)

    Delombard, Richard; McQuillen, John; Chao, David

    2008-01-01

    Pool boiling in microgravity is an area of both scientific and practical interest. By conducting tests in microgravity, it is possible to assess the effect of buoyancy on the overall boiling process and assess the relative magnitude of effects with regards to other "forces" and phenomena such as Marangoni forces, liquid momentum forces, and microlayer evaporation. The Boiling eXperiment Facility is now being built for the Microgravity Science Glovebox that will use normal perfluorohexane as a test fluid to extend the range of test conditions to include longer test durations and less liquid subcooling. Two experiments, the Microheater Array Boiling Experiment and the Nucleate Pool Boiling eXperiment will use the Boiling eXperiment Facility. The objectives of these studies are to determine the differences in local boiling heat transfer mechanisms in microgravity and normal gravity from nucleate boiling, through critical heat flux and into the transition boiling regime and to examine the bubble nucleation, growth, departure and coalescence processes. Custom-designed heaters will be utilized to achieve these objectives.

  9. Investigation of Enhanced Boiling Heat Transfer from Porous Surfaces

    Institute of Scientific and Technical Information of China (English)

    LinZhiping; MaTongze; 等

    1994-01-01

    Experimental investigations of boiling heat transfer from porous surfaces at atmospheric pressure were performne.The porous surfaces are plain tubes coverd with metal screens.V-shaped groove tubes covered with screens,plain tubes sintered with screens.and V-shaped groove tubes sintered with screens,The experimental results show that sintering metal screens around spiral V-shaped groove tubes can greatly improve the boiling heat transfer,The boiling hystesis was observed in the experiment.This paper discusses the mechanism of the boiling heat transfer from those kinds of porous surfaces stated above.

  10. Boiling point: government neglect, corporate abuse, and Canada's water crisis

    National Research Council Canada - National Science Library

    Barlow, Maude

    2016-01-01

    "In Boiling Point, bestselling author and activist Maude Barlow lays bare the issues facing Canada's water reserves, including long-outdated water laws, unmapped and unprotected groundwater reserves...

  11. Pool boiling heat transfer performance of Newtonian nanofluids

    Energy Technology Data Exchange (ETDEWEB)

    Soltani, Saide; Etemad, Seyed Gholamreza [Isfahan University of Technology, Department of Chemical Engineering, Isfahan (Iran); Thibault, Jules [University of Ottawa, Department of Chemical and Biological Engineering, Ottawa, ON (Canada)

    2009-10-15

    Experimental measurements were carried out on the boiling heat transfer characteristics of {gamma}-Al{sub 2}O{sub 3}/water and SnO{sub 2}/water Newtonian nanofluids. Nanofluids are liquid suspensions containing nanoparticles with sizes smaller than 100 nm. In this research, suspensions with different concentrations of {gamma}-Al{sub 2}O{sub 3} and SnO{sub 2} nanoparticles in water were studied under nucleate pool boiling heat transfer conditions. Results show that nanofluids possess noticeably higher boiling heat transfer coefficients than the base fluid. The boiling heat transfer coefficients depend on the type and concentration of nanoparticles. (orig.)

  12. Boiling heat transfer modern developments and advances

    CERN Document Server

    Lahey, Jr, RT

    2013-01-01

    This volume covers the modern developments in boiling heat transfer and two-phase flow, and is intended to provide industrial, government and academic researchers with state-of-the-art research findings in the area of multiphase flow and heat transfer technology. Special attention is given to technology transfer, indicating how recent significant results may be used for practical applications. The chapters give detailed technical material that will be useful to engineers and scientists who work in the field of multiphase flow and heat transfer. The authors of all chapters are members of the

  13. Explosive Boiling of Superheated Cryogenic Liquids

    CERN Document Server

    Baidakov, V G

    2007-01-01

    The monograph is devoted to the description of the kinetics of spontaneous boiling of superheated liquefied gases and their solutions. Experimental results are given on the temperature of accessible superheating, the limits of tensile strength of liquids due to processes of cavitation and the rates of nucleation of classical and quantum liquids. The kinetics of evolution of the gas phase is studied in detail for solutions of cryogenic liquids and gas-saturated fluids. The properties of the critical clusters (bubbles of critical sizes) of the newly evolving gas phase are analyzed for initial st

  14. Heat transfer coefficient for boiling carbon dioxide

    DEFF Research Database (Denmark)

    Knudsen, Hans Jørgen Høgaard; Jensen, Per Henrik

    1998-01-01

    between the measured and the calculated heat transfer coefficient is nearly constant and equal 1.9. With this factor the correlation predicts the measured data within 14% (RMS). The pressure drop is of the same order as the measuring uncertainty and the pressure drop has not been compared with correlation's.......Heat transfer coefficient and pressure drop for boiling carbon dioxide (R744) flowing in a horizontal pipe has been measured. The calculated heat transfer coeeficient has been compared with the Chart correlation of Shah. The Chart Correlation predits too low heat transfer coefficient but the ratio...

  15. Simplified Production of Organic Compounds Containing High Enantiomer Excesses

    Science.gov (United States)

    Cooper, George W. (Inventor)

    2015-01-01

    The present invention is directed to a method for making an enantiomeric organic compound having a high amount of enantiomer excesses including the steps of a) providing an aqueous solution including an initial reactant and a catalyst; and b) subjecting said aqueous solution simultaneously to a magnetic field and photolysis radiation such that said photolysis radiation produces light rays that run substantially parallel or anti-parallel to the magnetic field passing through said aqueous solution, wherein said catalyst reacts with said initial reactant to form the enantiomeric organic compound having a high amount of enantiomer excesses.

  16. Modal control of unstable boiling states in three-dimensional nonlinear pool-boiling

    NARCIS (Netherlands)

    van Gils, R.W.; Speetjens, M.F.M; Zwart, Heiko J.; Nijmeijer, H.

    2014-01-01

    Topic is feedback stabilisation of a nonlinear pool-boiling system in three spatial dimensions (3D). Regulation of its unstable (non-uniform) equilibria has great potential for application in micro-electronics cooling and thermal-management systems. Here, as a first step, stabilisation of such 3D

  17. Modal control of unstable boiling states in three-dimensional nonlinear pool-boiling

    NARCIS (Netherlands)

    Gils, van R.W.; Speetjens, M.F.M; Zwart, H.J.; Nijmeijer, H.

    2014-01-01

    Topic is feedback stabilisation of a nonlinear pool-boiling system in three spatial dimensions (3D). Regulation of its unstable (non-uniform) equilibria has great potential for application in micro-electronics cooling and thermal-management systems. Here, as a first step, stabilisation of such 3D eq

  18. Parametric investigation on transient boiling heat transfer of metal rod cooled rapidly in water pool

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Chi Young [Department of Fire Protection Engineering, Pukyong National University, 45, Yongso-ro, Nam-gu, Busan 48513 (Korea, Republic of); Kim, Sunwoo, E-mail: swkim@alaska.edu [Mechanical Engineering Department, University of Alaska Fairbanks, P. O. Box 755905, Fairbanks, AK 99775-5905 (United States)

    2017-03-15

    Highlights: • Effects of liquid subcooling, surface coating, material property, and surface oxidation are examined. • Liquid subcooling affects remarkably the quenching phenomena. • Cr-coated surfaces for ATF might extend the quenching duration. • Solids with low heat capacity shorten the quenching duration. • Surface oxidation can affect strongly the film boiling heat transfer and MFB point. - Abstract: In this work, the effects of liquid subcooling, surface coating, material property, and surface oxidation on transient pool boiling heat transfer were investigated experimentally using the vertical metal rod and quenching method. The change in rod temperature was measured with time during quenching, and the visualization of boiling around the test specimen was performed using the high-speed video camera. As the test materials, the zircaloy (Zry), stainless steel (SS), niobium (Nb), and copper (Cu) were tested. In addition, the chromium-coated niobium (Cr-Nb) and chromium-coated stainless steel (Cr-SS) were prepared for accident tolerant fuel (ATF) application. Low liquid subcooling and Cr-coating shifted the quenching curve to the right, which indicates a prolongation of quenching duration. On the other hand, the material with small heat capacity and surface oxidation caused the quenching curve to move to the left. To examine the influence of the material property and surface oxidation on the film boiling heat transfer performance and minimum film boiling (MFB) point in more detail, the wall temperature and heat flux were calculated from the present transient temperature profile using the inverse heat transfer analysis, and then the curves of wall temperature and heat flux in the film boiling regime were obtained. In the present experimental conditions, the effect of material property on the film boiling heat transfer performance and MFB point seemed to be minor. On the other hand, based on the experimental results of the Cu test specimen, the surface

  19. Flow Structures Around Micro-bubbles During Subcooled Nucleate Boiling

    Institute of Scientific and Technical Information of China (English)

    WANG Hao; PENG Xiao-Feng; David M. Christopher; WANG Bu-Xuan

    2005-01-01

    The flow structures were investigated around micro bubbles on extremely thin wires during subcooled nucleate boiling. Jet flows emanating from the bubbles were observed visually with the fluid field measurement using high-speed photography and a PIV system. The jet flows induced a strong pumping effect around a bubble. The multi-jet structure was further observed experimentally, indicating the evolution of flow structure around micro bubbles. Numerical simulations explore that the jet flows were induced by a strong Marangoni effect due to high temperature gradients near the wire. The bubble interface with multi-jet structure has abnormal temperature distribution such that the coolest parts were observed at two sides of a bubble extending into the subcooled bulk liquid rather than at the top. Evaporation and condensation on the bubble interface play important roles not only in controlling the intensity of the jet flow, but also in bringing out the multi-jet structure.

  20. Optimizing the Combination of Smoking and Boiling on Quality of Korean Traditional Boiled Loin (M. longissimus dorsi).

    Science.gov (United States)

    Choi, Yun-Sang; Kim, Hyun-Wook; Hwang, Ko-Eun; Song, Dong-Heon; Kim, Yong-Jae; Jung, Tae-Jun; Kim, Young-Boong; Kim, Cheon-Jei

    2015-01-01

    The combined effects of smoking and boiling on the proximate composition, technological quality traits, shear force, and sensory characteristics of the Korean traditional boiled loin were studied. Cooking loss, processing loss, and shear force were lower in the smoked/boiled samples than those in the control (without smoking treatment) (pboiled loin samples between the control and treatment did not differ significantly in protein, fat, or ash contents, or pH values (p>0.05). The treated samples had higher score for overall acceptability than the control (pboiled loin treated with smoking for 60 min before boiling had improved physicochemical properties and sensory characteristics.

  1. Flow impinging effect of critical heat flux and nucleation boiling heat transfer on a downward facing heating surface

    Energy Technology Data Exchange (ETDEWEB)

    Hsieh, Huai-En; Chen, Mei-Shiue; Chen, Jyun-Wei; Lin, Wei-Keng; Pei, Bau-Shei [National Tsing Hua Univ., Taiwan (China). Inst. of Nuclear Engineering and Science

    2015-05-15

    Boiling heat transfer has a high heat removal capability in convective cooling. However, the heat removal capability of downward-facing boiling is significantly worse than that of upward-facing cases because of the confined buoyancy effect. This study was inspired by the conception of external reactor vessel cooling (ERVC) condition relevant to the in-vessel retention (IVR) design of Westinghouse AP1000 plant. In the present study, a small-scale test facility had been established to investigate the local phenomena of boiling heat transfer under a downward-facing horizontal heated surface with impinging coolant flow. In this study, the surface temperature, heat flux information and several specific scenes of bubbles are taken down throughout the boiling processes for detailed investigation. It is observed that bubbles are confined under the downward-facing heated surface, which causes a worse heat transfer rate and a lower critical heat flux (CHF) limit than upward-facing boiling. Nevertheless, the impinging coolant flow is found to disturb the thermal boundary layer formed by the heated surface, so the CHF increases with an increase of coolant flow rate. In addition, during nucleate boiling, it is discovered that the growth, combination and dissipation of bubbles induce turbulent wakes and therefore enhance the heat transfer capability.

  2. Development boiling to sprinkled tube bundle

    Directory of Open Access Journals (Sweden)

    Kracík Petr

    2016-01-01

    Full Text Available This paper presents results of a studied heat transfer coefficient at the surface of a sprinkled tube bundle where boiling occurs. Research in the area of sprinkled exchangers can be divided into two major parts. The first part is research on heat transfer and determination of the heat transfer coefficient at sprinkled tube bundles for various liquids, whether boiling or not. The second part is testing of sprinkle modes for various tube diameters, tube pitches and tube materials and determination of individual modes’ interface. All results published so far for water as the falling film liquid apply to one to three tubes for which the mentioned relations studied are determined in rigid laboratory conditions defined strictly in advance. The sprinkled tubes were not viewed from the operational perspective where there are more tubes and various modes may occur in different parts with various heat transfer values. The article focuses on these processes. The tube is located in a low-pressure chamber where vacuum is generated using an exhauster via ejector. The tube consists of smooth copper tubes of 12 mm diameter placed horizontally one above another.

  3. Development boiling to sprinkled tube bundle

    Science.gov (United States)

    Kracík, Petr; Pospíšil, Jiří

    2016-03-01

    This paper presents results of a studied heat transfer coefficient at the surface of a sprinkled tube bundle where boiling occurs. Research in the area of sprinkled exchangers can be divided into two major parts. The first part is research on heat transfer and determination of the heat transfer coefficient at sprinkled tube bundles for various liquids, whether boiling or not. The second part is testing of sprinkle modes for various tube diameters, tube pitches and tube materials and determination of individual modes' interface. All results published so far for water as the falling film liquid apply to one to three tubes for which the mentioned relations studied are determined in rigid laboratory conditions defined strictly in advance. The sprinkled tubes were not viewed from the operational perspective where there are more tubes and various modes may occur in different parts with various heat transfer values. The article focuses on these processes. The tube is located in a low-pressure chamber where vacuum is generated using an exhauster via ejector. The tube consists of smooth copper tubes of 12 mm diameter placed horizontally one above another.

  4. Knowledge and abilities catalog for nuclear power plant operators: Boiling water reactors, Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-08-01

    The Knowledge and Abilities Catalog for Nuclear Power Plant Operators: Boiling-Water Reactors (BWRs) (NUREG-1123, Revision 1) provides the basis for the development of content-valid licensing examinations for reactor operators (ROs) and senior reactor operators (SROs). The examinations developed using the BWR Catalog along with the Operator Licensing Examiner Standards (NUREG-1021) and the Examiner`s Handbook for Developing Operator Licensing Written Examinations (NUREG/BR-0122), will cover the topics listed under Title 10, Code of Federal Regulations, Part 55 (10 CFR 55). The BWR Catalog contains approximately 7,000 knowledge and ability (K/A) statements for ROs and SROs at BWRs. The catalog is organized into six major sections: Organization of the Catalog, Generic Knowledge and Ability Statements, Plant Systems grouped by Safety Functions, Emergency and Abnormal Plant Evolutions, Components, and Theory. Revision 1 to the BWR Catalog represents a modification in form and content of the original catalog. The K/As were linked to their applicable 10 CFR 55 item numbers. SRO level K/As were identified by 10 CFR 55.43 item numbers. The plant-wide generic and system generic K/As were combined in one section with approximately one hundred new K/As. Component Cooling Water and Instrument Air Systems were added to the Systems Section. Finally, High Containment Hydrogen Concentration and Plant Fire On Site evolutions added to the Emergency and Abnormal Plant Evolutions section.

  5. High Gain Hybrid Graphene-Organic Semiconductor Phototransistors

    NARCIS (Netherlands)

    Huisman, Everardus H.; Shulga, Artem G.; Zomer, Paul J.; Tombros, Nikolaos; Bartesaghi, Davide; Bisri, Satria Zulkarnaen; Loi, Maria A.; Koster, L. Jan Anton; van Wees, Bart J.

    2015-01-01

    Hybrid phototransistors of graphene and the organic semiconductor poly(3-hexylthiophene-2,5-diyl) (P3HT) are presented. Two types of phototransistors are demonstrated with a charge carrier transit time that differs by more than 6 orders of magnitude. High transit time devices are fabricated using a

  6. Electric fields effect on the rise of single bubbles during boiling

    Energy Technology Data Exchange (ETDEWEB)

    Siedel, Samuel; Cioulachtjian, Serge; Bonjour, Jocelyn [CETHIL - UMR 5008 CNRS INSA-Lyon Univ. Lyon 1, INLSA-Lyon (France)], e-mail: jocelyn.bonjour@insa-lyon.fr

    2009-07-01

    An experimental study of saturated pool boiling on a single artificial nucleation site without and with the application of an electric field on the boiling surface has been conducted. N-pentane is boiling on a copper surface and is recorded with a high speed camera providing high quality pictures and movies. The accuracy of the visualization allowed establishing an experimental bubble growth law from a large number of experiments. This law shows that the evaporation rate is decreasing during the bubble growth, and underlines the importance of liquid motion induced by the preceding bubble. Bubble rise is therefore studied: once detached, bubbles accelerate vertically until reaching a maximum velocity in good agreement with a correlation from literature. The bubbles then turn to another direction. The effect of applying an electric field on the boiling surface in finally studied. In addition to changes of the bubble shape, changes are also shown in the liquid plume and the convective structures above the surface. Lower maximum rising velocities were measured in the presence of electric fields, especially with a negative polarity. (author)

  7. Acoustic field interaction with a boiling system under terrestrial gravity and microgravity.

    Science.gov (United States)

    Sitter, J S; Snyder, T J; Chung, J N; Marston, P L

    1998-11-01

    Pool boiling experiments from a platinum wire heater in FC-72 liquid were conducted under terrestrial and microgravity conditions, both with and without the presence of a high-intensity acoustic standing wave within the fluid. The purpose of this research was to study the interaction between an acoustic field and a pool boiling system in normal gravity and microgravity. The absence of buoyancy in microgravity complicates the process of boiling. The acoustic force on a vapor bubble generated from a heated wire in a standing wave was shown to be able to play the role of buoyancy in microgravity. The microgravity environment was achieved with 0.6 and 2.1-s drop towers. The sound was transmitted through the fluid medium by means of a half wavelength sonic transducer driven at 10.18 kHz. At high enough acoustic pressure amplitudes cavitation and streaming began playing an important role in vapor bubble dynamics and heat transfer. Several different fixed heat fluxes were chosen for the microgravity experiment and the effects of acoustics on the surface temperature of the heater were recorded and the vapor bubble movement was filmed. Video images of the pool boiling processes and heat transfer data are presented.

  8. Multiphysics modeling of two-phase film boiling within porous corrosion deposits

    Science.gov (United States)

    Jin, Miaomiao; Short, Michael

    2016-07-01

    Porous corrosion deposits on nuclear fuel cladding, known as CRUD, can cause multiple operational problems in light water reactors (LWRs). CRUD can cause accelerated corrosion of the fuel cladding, increase radiation fields and hence greater exposure risk to plant workers once activated, and induce a downward axial power shift causing an imbalance in core power distribution. In order to facilitate a better understanding of CRUD's effects, such as localized high cladding surface temperatures related to accelerated corrosion rates, we describe an improved, fully-coupled, multiphysics model to simulate heat transfer, chemical reactions and transport, and two-phase fluid flow within these deposits. Our new model features a reformed assumption of 2D, two-phase film boiling within the CRUD, correcting earlier models' assumptions of single-phase coolant flow with wick boiling under high heat fluxes. This model helps to better explain observed experimental values of the effective CRUD thermal conductivity. Finally, we propose a more complete set of boiling regimes, or a more detailed mechanism, to explain recent CRUD deposition experiments by suggesting the new concept of double dryout specifically in thick porous media with boiling chimneys.

  9. A highly porous metal-organic framework for large organic molecule capture and chromatographic separation.

    Science.gov (United States)

    Li, Pei-Zhou; Su, Jie; Liang, Jie; Liu, Jia; Zhang, Yuanyuan; Chen, Hongzhong; Zhao, Yanli

    2017-03-25

    A highly porous metal-organic framework (MOF) with large pores was successfully obtained via solvothermal assembly of a "click"-extended tricarboxylate ligand and Zn(ii) ions. The inherent feature of large-molecule accessible pores endows the MOF with a unique property for utilization toward large guest molecules.

  10. Boiling treatment of ABS and PS plastics for flotation separation.

    Science.gov (United States)

    Wang, Chong-qing; Wang, Hui; Wu, Bao-xin; Liu, Qun

    2014-07-01

    A new physical method, namely boiling treatment, was developed to aid flotation separation of acrylonitrile-butadiene-styrene (ABS) and polystyrene (PS) plastics. Boiling treatment was shown to be effective in producing a hydrophilic surface on ABS plastic. Fourier Transform Infrared analysis was conducted to investigate the mechanism of boiling treatment of ABS. Surface rearrangement of polymer may be responsible for surface change of boiling treated ABS, and the selective influence of boiling treatment on the floatability of boiling treated plastics may be attributed to the difference in the molecular mobility of polymer chains. The effects of flotation time, frother concentration and particle size on flotation behavior of simple plastic were investigated. Based on flotation behavior of simple plastic, flotation separation of boiling treatment ABS and PS with different particle sizes was achieved efficiently. The purity of ABS and PS was up to 99.78% and 95.80%, respectively; the recovery of ABS and PS was up to 95.81% and 99.82%, respectively. Boiling treatment promotes the industrial application of plastics flotation and facilitates plastic recycling.

  11. Thermal-hydraulic performance of convective boiling jet array impingement

    Science.gov (United States)

    Jenkins, R.; De Brún, C.; Kempers, R.; Lupoi, R.; Robinson, A. J.

    2016-09-01

    Jet impingement boiling is investigated with regard to heat transfer and pressure drop performance using a novel laser sintered 3D printed jet impingement manifold design. Water was the working fluid at atmospheric pressure with inlet subcooling of 7oC. The convective boiling performance of the impinging jet system was investigated for a flat copper target surface for 2700≤Re≤5400. The results indicate that the heat transfer performance of the impinging jet is independent of Reynolds number for fully developed boiling. Also, the investigation of nozzle to plate spacing shows that low spacing delays the onset of nucleate boiling causing a superheat overshoot that is not observed with larger gaps. However, no sensitivity to the gap spacing was measured once boiling was fully developed. The assessment of the pressure drop performance showed that the design effectively transfers heat with low pumping power requirements. In particular, owing to the insensitivity of the heat transfer to flow rate during fully developed boiling, the coefficient of performance of jet impingement boiling in the fully developed boiling regime deteriorates with increased flow rate due to the increase in pumping power flux.

  12. Critical heat flux in flow boiling in microchannels

    CERN Document Server

    Saha, Sujoy Kumar

    2015-01-01

    This Brief concerns the important problem of critical heat flux in flow boiling in microchannels. A companion edition in the SpringerBrief Subseries on Thermal Engineering and Applied Science to “Heat Transfer and Pressure Drop in Flow Boiling in Microchannels,” by the same author team, this volume is idea for professionals, researchers, and graduate students concerned with electronic cooling.

  13. Rewetting and Flow Film Boiling Along Hot Surface

    Institute of Scientific and Technical Information of China (English)

    王补宣Thermal Engineering Department; Tsinghua University; Beijing 100084; PRC; 彭晓峰

    1994-01-01

    The recent investigations on the rewettmg and film boiling of liquid flowing along a hot/heated surface are briefly reviewed and discussed.Some advanced theoretical analyses are conducted and new conclusions achieved.These investigations describe the fundamental characteristics of liquid flow boiling and further the complicated rewetting phenomena,and have resulted in considerable insight intothe mechanism.

  14. Prospective Primary School Teachers' Perceptions on Boiling and Freezing

    Science.gov (United States)

    Senocak, Erdal

    2009-01-01

    The aim of this study was to investigate the perceptions of prospective primary school teachers on the physical state of water during the processes of boiling and freezing. There were three stages in the investigation: First, open-ended questions concerning the boiling and freezing of water were given to two groups of prospective primary school…

  15. Comparison of direct boiling method with commercial kits for extracting fecal microbiome DNA by Illumina sequencing of 16S rRNA tags.

    Science.gov (United States)

    Peng, Xin; Yu, Ke-Qiang; Deng, Guan-Hua; Jiang, Yun-Xia; Wang, Yu; Zhang, Guo-Xia; Zhou, Hong-Wei

    2013-12-01

    Low cost and high throughput capacity are major advantages of using next generation sequencing (NGS) techniques to determine metagenomic 16S rRNA tag sequences. These methods have significantly changed our view of microorganisms in the fields of human health and environmental science. However, DNA extraction using commercial kits has shortcomings of high cost and time constraint. In the present study, we evaluated the determination of fecal microbiomes using a direct boiling method compared with 5 different commercial extraction methods, e.g., Qiagen and MO BIO kits. Principal coordinate analysis (PCoA) using UniFrac distances and clustering showed that direct boiling of a wide range of feces concentrations gave a similar pattern of bacterial communities as those obtained from most of the commercial kits, with the exception of the MO BIO method. Fecal concentration by boiling method affected the estimation of α-diversity indices, otherwise results were generally comparable between boiling and commercial methods. The operational taxonomic units (OTUs) determined through direct boiling showed highly consistent frequencies with those determined through most of the commercial methods. Even those for the MO BIO kit were also obtained by the direct boiling method with high confidence. The present study suggested that direct boiling could be used to determine the fecal microbiome and using this method would significantly reduce the cost and improve the efficiency of the sample preparation for studying gut microbiome diversity. © 2013 Elsevier B.V. All rights reserved.

  16. Computation of boiling water on circular finned tubes

    Energy Technology Data Exchange (ETDEWEB)

    Fan, C.C.; Liaw, S.P. [National Taiwan Ocean Univ., Keelung (Taiwan, Province of China). Dept. of Mechanical and Marine Engineering

    1999-04-01

    This study investigates the maximum heat transfer rate and the critical temperature of circular finned tubes in a boiling liquid. The analysis is conducted numerically by solving a two-dimensional heat conduction equation in a steady state. The dependence between heat flux and the temperature at the inner wall of the tube is quantified. Varying the width, height, and pitch of fins, an optimal finned tube with efficient heat transfer rate can be obtained. In the theoretical approach the successive over relaxation (S.O.R.) accompanied with Multi-grid scheme is used. The local heat transfer rates are assumed to follow power-law-type temperature dependence. The initial guess at very high temperatures or so-called a cooling process is also executed in a same way. The results reveal that increasing either the width or the height of a fin increases the total heat transfer rate.

  17. Interface oscillation of subcooled flow boiling in locally heated microchannels

    Science.gov (United States)

    Liu, J. T.; Peng, X. F.

    2009-02-01

    An investigation was conducted to understand flow boiling of subcooled de-ionized water in locally heated parallel microchannels. High-speed visualization technology was employed to visually observe the transient phase change process in an individual microchannel. Signal analysis method was employed in studying the interface movement and phase change process. The phase change at locally heated condition was different from those at entirely heated condition where elongated bubble(s) stayed quasi-stable for a long time without venting out. Diversified and intensive interface oscillation was observed occurring on both of the upstream and downstream bubble caps. Evaporation and condensation modes were characterized with distinguished oscillation frequencies. The film-driven oscillations of both evaporating and condensing interfaces generally operated at higher frequencies than the oscillations driven by nucleation or dropwise condensation.

  18. Boiling visualization on vertical fins with tunnel-pore structures

    Directory of Open Access Journals (Sweden)

    Kaniowski Robert

    2012-04-01

    Full Text Available The paper presents experimental studies of nucleate boiling heat transfer from a system of connected horizontal and vertical subsurface tunnels. The experiments were carried out for water at atmospheric pressure. The tunnel external covers were manufactured out of perforated copper foil (holes diameter 0.3 mm, sintered with the mini-fins, formed on the vertical side of the 10 mm high rectangular fins and horizontal inter-fin surface. The image acquisition speed was 493 fps (at resolution 400 × 300 pixels with Photonfocus PHOT MV-D1024-160-CL camera. Visualization investigations aimed to identify nucleation sites and flow patterns and to determine the bubble departure diameter and frequency at various superheats for vertical tunnels. At low superheat vapor bubbles are generated nearly exclusively by the vertical tunnel. At medium values of superheat, pores of the horizontal tunnel activate.

  19. Investigation of vapor film motion regularities at boiling liquids

    Directory of Open Access Journals (Sweden)

    Zeigarnik Y.U.

    2013-04-01

    Full Text Available The experimental investigation of the saturated Freon-113 and distilled water film boiling on spheres with different diameters at atmospheric pressure under conditions of free convection is executed. With high-speed video average thickness and cumulative distribution function of vapor film as a function of the angle was measured. It was found that with increasing the angle the average thickness of vapor film can change by different laws depending on diameter of the sphere and the temperature difference. It was found also that the increase in the average vapor film thickness with increasing angle is more connected with the increase of large components of cumulative distribution function. It also noted the presence of quasi-periodic pulsations of the vapor film thickness in the lower part, which eventually largely determine the behavior of the interface at large angles.

  20. Flow boiling of water on nanocoated surfaces in a microchannel

    CERN Document Server

    Phan, Hai Trieu; Marty, Philippe; Colasson, Stéphane; Gavillet, Jérôme

    2010-01-01

    Experiments were performed to study the effects of surface wettability on flow boiling of water at atmospheric pressure. The test channel is a single rectangular channel 0.5 mm high, 5 mm wide and 180 mm long. The mass flux was set at 100 kg/m2 s and the base heat flux varied from 30 to 80 kW/m2. Water enters the test channel under subcooled conditions. The samples are silicone oxide (SiOx), titanium (Ti), diamond-like carbon (DLC) and carbon-doped silicon oxide (SiOC) surfaces with static contact angles of 26{\\deg}, 49{\\deg}, 63{\\deg} and 103{\\deg}, respectively. The results show significant impacts of surface wettability on heat transfer coefficient.

  1. Expanded organic building units for the construction of highly porous metal-organic frameworks.

    Science.gov (United States)

    Kong, Guo-Qiang; Han, Zhi-Da; He, Yabing; Ou, Sha; Zhou, Wei; Yildirim, Taner; Krishna, Rajamani; Zou, Chao; Chen, Banglin; Wu, Chuan-De

    2013-10-25

    Two new organic building units that contain dicarboxylate sites for their self-assembly with paddlewheel [Cu2(CO2)4] units have been successfully developed to construct two isoreticular porous metal-organic frameworks (MOFs), ZJU-35 and ZJU-36, which have the same tbo topologies (Reticular Chemistry Structure Resource (RCSR) symbol) as HKUST-1. Because the organic linkers in ZJU-35 and ZJU-36 are systematically enlarged, the pores in these two new porous MOFs vary from 10.8 Å in HKUST-1 to 14.4 Å in ZJU-35 and 16.5 Å in ZJU-36, thus leading to their higher porosities with Brunauer-Emmett-Teller (BET) surface areas of 2899 and 4014 m(2) g(-1) for ZJU-35 and ZJU-36, respectively. High-pressure gas-sorption isotherms indicate that both ZJU-35 and ZJU-36 can take up large amounts of CH4 and CO2, and are among the few porous MOFs with the highest volumetric storage of CH4 under 60 bar and CO2 under 30 bar at room temperature. Their potential for high-pressure swing adsorption (PSA) hydrogen purification was also preliminarily examined and compared with several reported MOFs, thus indicating the potential of ZJU-35 and ZJU-36 for this important application. Studies show that most of the highly porous MOFs that can volumetrically take up the greatest amount of CH4 under 60 bar and CO2 under 30 bar at room temperature are those self-assembled from organic tetra- and hexacarboxylates that contain m-benzenedicarboxylate units with the [Cu2(CO2)4] units, because this series of MOFs can have balanced porosities, suitable pores, and framework densities to optimize their volumetric gas storage. The realization of the two new organic building units for their construction of highly porous MOFs through their self-assembly with [Cu2(CO2)4] units has provided great promise for the exploration of a large number of new tetra- and hexacarboxylate organic linkers based on these new organic building units in which different aromatic backbones can be readily incorporated

  2. Numerical study of subcooled boiling phenomena using a component analysis code, CUPID

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Ba-Ro; Lee, Yeon-Gun [Jeju National University, Jeju (Korea, Republic of)

    2015-10-15

    In this study, a couple of subcooled boiling experiments at high- (> 10 bar) and low-pressure (near atmospheric pressure) conditions are analyzed using a three-dimensional thermal-hydraulic component code, CUPID. And then the analysis results compared with the results using MARS-KS code. Subcooled boiling experiments at high- and low pressure conditions are analyzed using a three dimensional thermal-hydraulic component code, CUPID. The predictions of the CUPID code shows good agreement with Christenses's data and Bartolomey's data obtained at high pressure conditions. Subcooled boiling is encountered in many industrial applications in the power and process industry. In nuclear reactors, under certain conditions, subcooled boiling may be encountered in the core. The movement of bubbles generated by subcooled boiling affect the heat transfer characteristics and the pressure drop of the system. Thus some experimental and analysis using safety codes works have been already performed by previous investigators. It has been reported that the existing safety analysis codes have some weaknesses in predicting subcooled boiling phenomena at low pressure conditions. Thus, it is required to improve the predictive capability of thermal-hydraulic analysis codes on subcooled boiling phenomenon at low-pressure conditions. At low pressure condition, the CUPID code generally is overestimated prediction of the void fraction. Thus, we did selected submodels in the heat partitioning model by sensitivity analysis. Selected submodels of M{sub c}ase 4 are Kocamustafaogullari and Ishii correlation model of active nucleate site density, N' and Fritz correlation model of bubble departure diameter, d{sub Bd} . And then, case 5 - 8 are reanalysis using submodels of M{sub c}ase 4. The calculated void fraction is compared the default CUPID code model to the modified CUPID code model. As a result, average void fraction error was reduced from 0.081 to 0.011 and 0.128 to 0.024, 0

  3. Influence of the wettability on the boiling onset.

    Science.gov (United States)

    Bourdon, B; Rioboo, R; Marengo, M; Gosselin, E; De Coninck, J

    2012-01-17

    Experimental investigation of pool boiling is conducted in stationary conditions over very smooth bronze surfaces covered by a very thin layer of gold presenting various surface treatments to isolate the role of wettability. We show that even with surfaces presenting mean roughness amplitudes below 10 nm the role of surface topography is of importance. The study shows also that wettability alone can trigger the boiling and that the boiling position on the surface can be controlled by chemical grafting using for instance alkanethiol. Moreover, boiling curves, that is, heat flux versus the surface superheat (which is the difference between the solid surface temperature and the liquid saturation temperature), are recorded and enabled to quantify, for this case, the significant reduction of the superheat at the onset of incipient boiling due to wettability. © 2011 American Chemical Society

  4. Mechanistic Multidimensional Modeling of Forced Convection Boiling Heat Transfer

    Directory of Open Access Journals (Sweden)

    Michael Z. Podowski

    2009-01-01

    Full Text Available Due to the importance of boiling heat transfer in general, and boiling crisis in particular, for the analysis of operation and safety of both nuclear reactors and conventional thermal power systems, extensive efforts have been made in the past to develop a variety of methods and tools to evaluate the boiling heat transfer coefficient and to assess the onset of temperature excursion and critical heat flux (CHF at various operating conditions of boiling channels. The objective of this paper is to present mathematical modeling concepts behind the development of mechanistic multidimensional models of low-quality forced convection boiling, including the mechanisms leading to temperature excursion and the onset of CHF.

  5. Boiling in porous media; Ebullition en milieux poreux

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-11

    This conference day of the French society of thermal engineers was devoted to the analysis of heat transfers and fluid flows during boiling phenomena in porous media. This book of proceedings comprises 8 communications entitled: `boiling in porous medium: effect of natural convection in the liquid zone`; `numerical modeling of boiling in porous media using a `dual-fluid` approach: asymmetrical characteristic of the phenomenon`; `boiling during fluid flow in an induction heated porous column`; `cooling of corium fragment beds during a severe accident. State of the art and the SILFIDE experimental project`; `state of knowledge about the cooling of a particulates bed during a reactor accident`; `mass transfer analysis inside a concrete slab during fire resistance tests`; `heat transfers and boiling in porous media. Experimental analysis and modeling`; `concrete in accidental situation - influence of boundary conditions (thermal, hydric) - case studies`. (J.S.)

  6. An experimental investigation of critical heat flux performance of hypervapotron in subcooled boiling

    Science.gov (United States)

    Chen, Peipei

    The successful use of subcooled flow boiling for high heat flux components requires that the critical heat flux (CHF), i.e., a fast reduction in the boiling heat transfer, must be avoided. Among the many techniques available to enhance CHF, particular attention has been focused on the hypervapotron concept. In this study, the CHF characteristics of the hypervapotron were experimentally investigated using a simulant fluid, R134a, which has been found to be an effective modeling fluid to simulate CHF in water-cooled environments. An experimental and modeling study of the subcooled boiling heat transfer on plain surface and hypervapotron has been conduced. A test facility was designed and constructed to perform required boiling heat transfer experiments. A high speed visualization system was utilized to give details of bubble formation and departure and of nucleation site density. Surface measurements of various specimens were performed to investigate the relationship between nucleation sites and surface microstructure. Full characterization of the hypervapotron effect as a function of fluid thermal hydraulic conditions was accomplished. A non-dimensional CHF correlation for smooth rectangular channels and the hypervapotron channel was developed and compared with experimental data in this work. In addition, a hot-spot model was developed to give predictions of critical heat flux on both plain and hypervapotron surfaces. It was developed on observations of bubble formation, departure and coalescence, and on the confirmation of nucleation structure on the heating surface. Finally, a numerical code was successfully developed to give CHF predictions for hypervapotron configurations. The simulation indicates that the better performance of CHF in hypervapotron configurations is a result of high conductivity material with augmented heating surfaces in subcooled boiling environment. Different fin dimensions were also tested numerically to compare the experimental results, and

  7. Transient measurement of temperature oscillation during noisy film boiling in superfluid helium II

    Institute of Scientific and Technical Information of China (English)

    ZHANG; Peng

    2001-01-01

    [1]Kobayashi, H.?Yasukochi, K., Maximum and minimum heat flux and temperature fluctuation in film-boiling states in superfluid helium, Adv. Cryog. Eng., 1980, 25: 372.[2]Kobayashi, H.?Yasukochi, K., A sample configuration effect on the heat transfer from metal surfaces to pressurized He II, Proc. ICEC, 1980, 8: 217.[3]Schwerdtner, M. V., Stamm, G., Tosi, A. N. et al. The boiling-up process in He II. Optical measurements and visualization, Cryogenics, 1992, 32: 775.[4]Schwerdtner, M. V., Poppes, W., Schmidt, D. W., Distortion of temperature signals in He II due to probe geometry, and a new improved probe, Cryogenics, 1989, 29: 132.[5]Shimazaki, T., Murakami, M.?Iida, T., Second sound wave heat transfer, thermal boundary layer formation and boiling: highly transient heat transport phenomena in He II, Cryogenics, 1995, 35: 645.[6]Zhang, P., Study of physical mechanism of film boiling in He II, Doctoral dissertation, Shanghai Jiaotong University, China, 1998.[7]Arp, V., State equation of liquid helium-4 from 0.8 to 2.5K, J. Low Temp. Phys., 1990, 79: 93.[8]Zhang, P., Kimura, S., Murakami, M. et al., Non-planar and non-linear second sound wave in He II, Chinese Physics Letters, 2000, 17: 43.

  8. Transient interaction of a boiling melt with a pulsed Nd:YAG-laser

    Science.gov (United States)

    Samarjy, R. S. M.; Kaplan, A. F. H.

    2017-01-01

    The boiling front induced by a pulsed Nd:YAG-laser at very slow translation speed was studied. The purpose is to understand fundamental melt movement mechanisms. The melt was observed by high speed imaging, with and without illumination. When switching on the laser beam a hole is drilled through a bulk of melt. The hole expands and the boiling pressure gradually opens the melt bridge, instead developing an interaction front similar to cutting. These conditions remain in quasi-steady state during the pulse. The ablation pressure from boiling shears waves down the front and keeps the melt downwards in a stable position. When switching off, the waves smoothen and in absence of boiling the surface tension drags the melt back upwards, to semi-torus-like Catenoid shape. Evidence on the large melt pool and its shape was achieved by three-dimensional reconstruction from cross section macrographs. The basic findings how melt can move with and without ablation pressure can enable controlled melt dynamics for various laser processing techniques, like remote cutting, ablation, keyhole welding or drilling.

  9. Transition process leading to microbubble emission boiling on horizontal circular heated surface in subcooled pool

    Science.gov (United States)

    Ueno, Ichiro; Ando, Jun; Horiuchi, Kazuna; Saiki, Takahito; Kaneko, Toshihiro

    2016-11-01

    Microbubble emission boiling (MEB) produces a higher heat flux than critical heat flux (CHF) and therefore has been investigated in terms of its heat transfer characteristics as well as the conditions under which MEB occurs. Its physical mechanism, however, is not yet clearly understood. We carried out a series of experiments to examine boiling on horizontal circular heated surfaces of 5 mm and of 10 mm in diameter, in a subcooled pool, paying close attention to the transition process to MEB. High-speed observation results show that, in the MEB regime, the growth, condensation, and collapse of the vapor bubbles occur within a very short time. In addition, a number of fine bubbles are emitted from the collapse of the vapor bubbles. By tracking these tiny bubbles, we clearly visualize that the collapse of the vapor bubbles drives the liquid near the bubbles towards the heated surface, such that the convection field around the vapor bubbles under MEB significantly differs from that under nucleate boiling. Moreover, the axial temperature gradient in a heated block (quasi-heat flux) indicates a clear difference between nucleate boiling and MEB. A combination of quasi-heat flux and the measurement of the behavior of the vapor bubbles allows us to discuss the transition to MEB. This work was financially supported by the 45th Research Grant in Natural Sciences from The Mitsubishi Foundation (2014 - 2015), and by Research Grant for Boiler and Pressurized Vessels from The Japan Boiler Association (2016).

  10. Effects of Hull Scratching, Soaking, and Boiling on Antinutrients in Japanese Red Sword Bean (Canavalia gladiata).

    Science.gov (United States)

    Une, Satsuki; Nonaka, Koji; Akiyama, Junich

    2016-10-01

    The effects of hull processing, soaking, and boiling on the content or activity of antinutrients in the red sword bean (RSB; Canavalia gladiata) were investigated. RSB seeds were compared with kidney bean (KB; Phaseolus vulgaris) seeds that are starch based and often used as processed products in Japan. RSB seeds had higher weight, thicker hull, and higher protein content, but lower moisture content compared with KB seeds. Because of the strong and thick hull, the relative water absorption of untreated RSB seeds was very low after soaking. Seeds were soaked after dehulling, scratching, and roasting. The results showed that hull scratching was the optimal method for increasing water absorption during soaking compared with dehulling and roasting. After soaking, the water used for soaking was discarded, since it had a high content of polyphenols and bitter taste, and RSB seeds were boiled in fresh water for 20, 40, and 60 min. The results showed that polyphenol and tannin contents, antioxidant activity, and hemagglutinating activity, as well as maltase, sucrase, and trypsin inhibitor activities in scratched RSB seeds decreased significantly after boiling compared with those in raw seeds, whereas amylase inhibitor activity showed no significant change. Overall, it was concluded that the combination of hull scratching, soaking, and boiling in fresh water can reduce thermal-stable or sensitive antinutrients in RSB and thus, significantly improve its nutritional value. © 2016 Institute of Food Technologists®.

  11. Single-bubble dynamics in pool boiling of one-component fluids.

    Science.gov (United States)

    Xu, Xinpeng; Qian, Tiezheng

    2014-06-01

    We numerically investigate the pool boiling of one-component fluids with a focus on the effects of surface wettability on the single-bubble dynamics. We employed the dynamic van der Waals theory [Phys. Rev. E 75, 036304 (2007)], a diffuse-interface model for liquid-vapor flows involving liquid-vapor transition in nonuniform temperature fields. We first perform simulations for bubbles on homogeneous surfaces. We find that an increase in either the contact angle or the surface superheating can enhance the bubble spreading over the heating surface and increase the bubble departure diameter as well and therefore facilitate the transition into film boiling. We then examine the dynamics of bubbles on patterned surfaces, which incorporate the advantages of both hydrophobic and hydrophilic surfaces. The central hydrophobic region increases the thermodynamic probability of bubble nucleation while the surrounding hydrophilic region hinders the continuous bubble spreading by pinning the contact line at the hydrophobic-hydrophilic intersection. This leads to a small bubble departure diameter and therefore prevents the transition from nucleate boiling into film boiling. With the bubble nucleation probability increased and the bubble departure facilitated, the efficiency of heat transfer on such patterned surfaces is highly enhanced, as observed experimentally [Int. J. Heat Mass Transfer 57, 733 (2013)]. In addition, the stick-slip motion of contact line on patterned surfaces is demonstrated in one-component fluids, with the effect weakened by surface superheating.

  12. Single-bubble dynamics in pool boiling of one-component fluids

    KAUST Repository

    Xu, Xinpeng

    2014-06-04

    We numerically investigate the pool boiling of one-component fluids with a focus on the effects of surface wettability on the single-bubble dynamics. We employed the dynamic van der Waals theory [Phys. Rev. E 75, 036304 (2007)], a diffuse-interface model for liquid-vapor flows involving liquid-vapor transition in nonuniform temperature fields. We first perform simulations for bubbles on homogeneous surfaces. We find that an increase in either the contact angle or the surface superheating can enhance the bubble spreading over the heating surface and increase the bubble departure diameter as well and therefore facilitate the transition into film boiling. We then examine the dynamics of bubbles on patterned surfaces, which incorporate the advantages of both hydrophobic and hydrophilic surfaces. The central hydrophobic region increases the thermodynamic probability of bubble nucleation while the surrounding hydrophilic region hinders the continuous bubble spreading by pinning the contact line at the hydrophobic-hydrophilic intersection. This leads to a small bubble departure diameter and therefore prevents the transition from nucleate boiling into film boiling. With the bubble nucleation probability increased and the bubble departure facilitated, the efficiency of heat transfer on such patterned surfaces is highly enhanced, as observed experimentally [Int. J. Heat Mass Transfer 57, 733 (2013)]. In addition, the stick-slip motion of contact line on patterned surfaces is demonstrated in one-component fluids, with the effect weakened by surface superheating.

  13. Template fabrication of highly ordered arrays of organic semiconductor nanowires

    Energy Technology Data Exchange (ETDEWEB)

    Heckel, Christian; Ostendorp, Stefan; Lei, Yong; Wilde, Gerhard [Institut fuer Materialphysik, Muenster (Germany)

    2011-07-01

    Porous alumina membrane (PAM) is a widely used template for the fabrication of highly ordered arrays of one-dimensional (1D) nanostructures. The structural parameters of the PAMs are adjustable, including the pore diameter and spacing, and the thickness of the membranes. And thus the structures of the 1D nanomaterials prepared using PAMs can be controlled. On the other hand, the investigation of organic semiconductors opens a new field of applications in computer technology like twistable displays or printing integrated circuits. In the current work, these two technologies are combined by depositing organic n-type semiconductors into the pores of PAMs using different synthesizing processes such as molecular evaporation and solution-phase self-assembly. As a result, highly ordered arrays of organic semiconducting wires are obtained within the pores with a diameter of about 50 nm, which indicates that it is possible to fill the pores with organic materials.The properties of these ''filled'' membranes are characterized by measuring the electrical properties of several nanowires pooled together and also of single nanowires by AFM-based methods.

  14. Hybrid modelling of a sugar boiling process

    CERN Document Server

    Lauret, Alfred Jean Philippe; Gatina, Jean Claude

    2012-01-01

    The first and maybe the most important step in designing a model-based predictive controller is to develop a model that is as accurate as possible and that is valid under a wide range of operating conditions. The sugar boiling process is a strongly nonlinear and nonstationary process. The main process nonlinearities are represented by the crystal growth rate. This paper addresses the development of the crystal growth rate model according to two approaches. The first approach is classical and consists of determining the parameters of the empirical expressions of the growth rate through the use of a nonlinear programming optimization technique. The second is a novel modeling strategy that combines an artificial neural network (ANN) as an approximator of the growth rate with prior knowledge represented by the mass balance of sucrose crystals. The first results show that the first type of model performs local fitting while the second offers a greater flexibility. The two models were developed with industrial data...

  15. Heat transfer coeffcient for boiling carbon dioxide

    DEFF Research Database (Denmark)

    Knudsen, Hans Jørgen Høgaard; Jensen, Per Henrik

    1997-01-01

    transfer coefficient but the ratio between the measured and the calculated heat transfer coefficient is nearly constant and equal 1.9. With this factor the correlation predicts the measured data within 14% (RMS). The pressure drop is of the same order as the measuring uncertainty and the pressure drop has......Heat transfer coefficient and pressure drop for boiling carbon dioxide (R744) flowing in a horizontal pipe has been measured. The pipe is heated by condensing R22 outside the pipe. The heat input is supplied by an electrical heater wich evaporates the R22. With the heat flux assumed constant over...... the whole surface and with measured temperature difference between the inner surface and the evaporation temperature a mean heat transfer coefficient is calculated. The calculated heat transfer coefficient has been compared with the Chart Correlation of Shah. The Chart Correlation predicts too low heat...

  16. Tuning the crystal polymorphs of organic semiconductor towards high performance organic transistors (Conference Presentation)

    Science.gov (United States)

    Zhen, Yonggang; He, Ping; Yi, Yuanping; Hu, Wenping

    2016-11-01

    Generally, the differences in crystal polymorph exhibit different narrow band structures, electron-phonon coupling, optoelectronic characteristics and charge transport properties, thus leading to different device performances of organic semiconductors for application in organic field-effect transistors (OFETs). Nowadays it still remains a big challenge to control organic crystal polymorph because the slight non-directional intermolecular interactions lead to the very small differences instructure and energy of cystal phases with several alternative packing arrangements. Therefore, the control of the crystal polymorphism towards high device performance has become a crucial issue in the field of organic semiconductors. Thienoacenes have been intensively investigated as very promising organic semiconductors with high stability and superior mobility for OFETs in the last decade. However, scare studies focused on the crystal polymorph of thienoacenes. Herein, we report the controllable growth of different crystal phases of dihexyl-substituted dibenzo[d,d']thieno[3,2-b;4,5-b']dithiophene (C6-DBTDT), which was synthesized in a new, facile and efficient method. Furthermore, OFETs based on microribbon-shaped β phase crystals showed the hole mobility up to 18.9 cm2 V-1 s-1, which is one of the highest value for p-type organic semiconductors measured under ambient conditions, while platelet-shaped α phase crystals displayed the lower hole mobility of 8.5 cm2 V-1 s-1. We clearly demonstrated that the selective growth of different crystal polymorph for C6-DBTDT can be achieved by using different substrate and solvents. The simple drop-cast fabrication with controllable crystal phase and air operation stability would open the possibility of thienoacene derivatives in the construction of micro- and nanoelectronics.

  17. Sodium boiling detection in LMFBRs by acoustic-neutronic cross correlation

    Energy Technology Data Exchange (ETDEWEB)

    Wright, S.A.

    1977-01-01

    The acoustic and neutronic noise signals caused by boiling are the signals primarily considered likely to detect sodium boiling in an LMFBR. Unfortunately, these signals may have serious signal-to-noise problems due to strong background noise sources. Neutronic-acoustic cross correlation techniques are expected to provide a means of improving the signal-to-noise ratio. This technique can improve the signal-to-noise ratio because the neutronic and acoustic signals due to boiling are highly correlated near the bubble repetition frequency, while the background noise sources are expected to be uncorrelated (or at most weakly correlated). An experiment was designed to show that the neutronic and acoustic noise signals are indeed highly correlated. The experiment consisted of simulating the void and pressure effects of local sodium boiling in the core of a zero-power reactor (ARK). The analysis showed that the neutronic and acoustic noise signals caused by boiling are almost perfectly correlated in a wide frequency band about the bubble repetition frequency. The results of the experiments were generalized to full-scale reactors to compare the inherent effectiveness of the methods which use the neutronic or acoustic signals alone with a hybrid method, which cross correlates the neutronic and acoustic signals. It was concluded that over a zone of the reactor where the void coefficient is sufficiently large (approximately 85 percent the core volume), the cross correlation method can provide a more rapid detection system for a given signal-to-noise ratio. However, where the void coefficient is small, one must probably rely on the acoustic method alone.

  18. Multiphysics modeling of two-phase film boiling within porous corrosion deposits

    Energy Technology Data Exchange (ETDEWEB)

    Jin, Miaomiao, E-mail: mmjin@mit.edu; Short, Michael, E-mail: hereiam@mit.edu

    2016-07-01

    Porous corrosion deposits on nuclear fuel cladding, known as CRUD, can cause multiple operational problems in light water reactors (LWRs). CRUD can cause accelerated corrosion of the fuel cladding, increase radiation fields and hence greater exposure risk to plant workers once activated, and induce a downward axial power shift causing an imbalance in core power distribution. In order to facilitate a better understanding of CRUD's effects, such as localized high cladding surface temperatures related to accelerated corrosion rates, we describe an improved, fully-coupled, multiphysics model to simulate heat transfer, chemical reactions and transport, and two-phase fluid flow within these deposits. Our new model features a reformed assumption of 2D, two-phase film boiling within the CRUD, correcting earlier models' assumptions of single-phase coolant flow with wick boiling under high heat fluxes. This model helps to better explain observed experimental values of the effective CRUD thermal conductivity. Finally, we propose a more complete set of boiling regimes, or a more detailed mechanism, to explain recent CRUD deposition experiments by suggesting the new concept of double dryout specifically in thick porous media with boiling chimneys. - Highlights: • A two-phase model of CRUD's effects on fuel cladding is developed and improved. • This model eliminates the formerly erroneous assumption of wick boiling. • Higher fuel cladding temperatures are predicted when accounting for two-phase flow. • Double-peaks in thermal conductivity vs. heat flux in experiments are explained. • A “double dryout” mechanism in CRUD is proposed based on the model and experiments.

  19. Mixture interlayer for high performance organic-inorganic perovskite photodetectors

    Science.gov (United States)

    Tang, Feng; Chen, Qi; Chen, Lei; Ye, Fengye; Cai, Jinhua; Chen, Liwei

    2016-09-01

    Organic-inorganic perovskites are promising light absorbing active materials for photodetectors; however, the performance of current organic-inorganic perovskite-based photodetectors are limited by the high dark current due to hole injection at the cathode interlayer typically composed of fullerene derivatives. We have developed a mixture interlayer by simply blending polymethyl methacrylate (PMMA) with [6,6]-phenyl-C61-butyric acidmethyl ester (PCBM). Scanning Kelvin probe microscopy imaging reveals that the presence of PMMA reduced the work function of the PCBM:PMMA interlayer, which leads to increased energy barrier for hole injection and better hole-blocking property. Optimized perovskite photodetector with PCBM:PMMA hole-blocking interlayer exhibits a high detectivity of 1.1 × 1013 Jones, a broad linear dynamic range of 112 dB, and a fast response time of 2.2 μs.

  20. Can Highly Oxidized Organics Contribute to Atmospheric New Particle Formation?

    Science.gov (United States)

    Ortega, Ismael K; Donahue, Neil M; Kurtén, Theo; Kulmala, Markku; Focsa, Cristian; Vehkamäki, Hanna

    2016-03-10

    Highly oxidized organic molecules may play a critical role in new-particle formation within Earth's atmosphere along with sulfuric acid, which has long been considered as a key compound in this process. Here we explore the interactions of these two partners, using quantum chemistry to find the formation free energies of heterodimers and trimers as well as the fastest evaporation rates of (2,2) tetramers. We find that the heterodimers are more strongly bound than pure sulfuric acid dimers. Their stability correlates well with the oxygen to carbon ratio of the organics, their volatility, and the number of hydrogen bonds formed. Most of the stable trimers contain one sulfuric acid and two organics (1,2), whereas many (2,2) tetramers evaporate quickly, probably due to the stability of (1,2) clusters. This finding agrees with recent experimental studies that show how new-particle formation involving oxidized organics and sulfuric acid may be rate-limited by activation of (1,2) trimers, confirming the importance of this process in the atmosphere.

  1. OH-initiated heterogeneous aging of highly oxidized organic aerosol

    Energy Technology Data Exchange (ETDEWEB)

    Kessler, Sean H.; Nah, Theodora; Daumit, Kelly E.; Smith, Jared D.; Leone, Stephen R.; Kolb, Charles E.; Worsnop, Douglas R.; Wilson, Kevin R.; Kroll, Jesse H.

    2011-12-05

    The oxidative evolution (“aging”) of organic species in the atmosphere is thought to have a major influence on the composition and properties of organic particulate matter, but remains poorly understood, particularly for the most oxidized fraction of the aerosol. Here we measure the kinetics and products of the heterogeneous oxidation of highly oxidized organic aerosol, with an aim of better constraining such atmospheric aging processes. Submicron particles composed of model oxidized organics—1,2,3,4-butanetetracarboxylic acid (C{sub 8}H{sub 10}O{sub 8}), citric acid (C{sub 6}H{sub 8}O{sub 7}), tartaric acid (C{sub 4}H{sub 6}O{sub 6}), and Suwannee River fulvic acid—were oxidized by gas-phase OH in a flow reactor, and the masses and elemental composition of the particles were monitored as a function of OH exposure. In contrast to our previous studies of less-oxidized model systems (squalane, erythritol, and levoglucosan), particle mass did not decrease significantly with heterogeneous oxidation. Carbon content of the aerosol always decreased somewhat, but this mass loss was approximately balanced by an increase in oxygen content. The estimated reactive uptake coefficients of the reactions range from 0.37 to 0.51 and indicate that such transformations occur at rates corresponding to 1-2 weeks in the atmosphere, suggesting their importance in the atmospheric lifecycle of organic particulate matter.

  2. Transition boiling heat transfer and the film transition regime

    Science.gov (United States)

    Ramilison, J. M.; Lienhard, J. H.

    1987-01-01

    The Berenson (1960) flat-plate transition-boiling experiment has been recreated with a reduced thermal resistance in the heater, and an improved access to those portions of the transition boiling regime that have a steep negative slope. Tests have been made in Freon-113, acetone, benzene, and n-pentane boiling on horizontal flat copper heaters that have been mirror-polished, 'roughened', or teflon-coated. The resulting data reproduce and clarify certain features observed by Berenson: the modest surface finish dependence of boiling burnout, and the influence of surface chemistry on both the minimum heat flux and the mode of transition boiling, for example. A rational scheme of correlation yields a prediction of the heat flux in what Witte and Lienhard (1982) previously identified as the 'film-transition boiling' region. It is also shown how to calculate the heat flux at the boundary between the pure-film, and the film-transition, boiling regimes, as a function of the advancing contact angle.

  3. Transition boiling heat transfer and the film transition regime

    Science.gov (United States)

    Ramilison, J. M.; Lienhard, J. H.

    1987-01-01

    The Berenson (1960) flat-plate transition-boiling experiment has been recreated with a reduced thermal resistance in the heater, and an improved access to those portions of the transition boiling regime that have a steep negative slope. Tests have been made in Freon-113, acetone, benzene, and n-pentane boiling on horizontal flat copper heaters that have been mirror-polished, 'roughened', or teflon-coated. The resulting data reproduce and clarify certain features observed by Berenson: the modest surface finish dependence of boiling burnout, and the influence of surface chemistry on both the minimum heat flux and the mode of transition boiling, for example. A rational scheme of correlation yields a prediction of the heat flux in what Witte and Lienhard (1982) previously identified as the 'film-transition boiling' region. It is also shown how to calculate the heat flux at the boundary between the pure-film, and the film-transition, boiling regimes, as a function of the advancing contact angle.

  4. Rejection of trace organic compounds by high-pressure membranes.

    Science.gov (United States)

    Kim, T U; Amy, G; Drewes, J E

    2005-01-01

    High-pressure membranes, encompassing reverse osmosis (RO), nanofiltration (NF), and low-pressure RO, may provide an effective treatment barrier for trace organic compounds including disinfection by-products (DBPs), pesticides, solvents, endocrine disrupting compounds (EDCs) and pharmaceutically active compounds (PhACs). The objective is to develop a mechanistic understanding of the rejection of trace organic compounds by high-pressure membranes, based on an integrated framework of compound properties, membrane properties, and operational conditions. Eight trace organic compounds, four DBPs and four chlorinated (halogenated) solvents, are being emphasized during an initial study, based on considerations of compound properties, occurrence, and health effects (regulations). Four polyamide FilmTec membranes; three reverse osmosis/RO (BW-400, LE-440, XLE-440) and one nanofiltration/NF (NF-90); are being characterized according to pure water permeability (PWP), molecular weight cutoff (MWCO), hydrophobicity (contact angle), and surface charge (zeta potential). It is noteworthy that rejections of compounds of intermediate hydrophobicity by the candidate membranes were observed to be less than salt rejections reported for these membranes, suggesting that transport of these solutes through these membranes is facilitated by solute-membrane interactions. We are continuing with diffusion cell measurements to describe solute-membrane interactions by estimation of diffusion coefficients through membranes pores, either hindered or facilitated.

  5. Bubble Dynamics, Two-Phase Flow, and Boiling Heat Transfer in Microgravity

    Science.gov (United States)

    Chung, Jacob N.

    1998-01-01

    wall temperature and heat flux near the wall would add to the database of knowledge which is necessary to understand the mechanisms of nucleate boiling. A heater array has been developed which contains 96 heater elements within a 2.5 mm square area. The temperature of each heater element is held constant by an electronic control system similar to a hot-wire anemometer. The voltage that is being applied to each heater element can be measured and digitized using a high-speed Analog to Digital (A/D) converter, and this digital information can be compiled into a series of heat-flux maps. Information for up to 10,000 heat flux maps can be obtained each second. The heater control system, the A/D system and the heater array construction are described in detail. Results are presented which show that this is an effective method of measuring the local heat flux during nucleate and transition boiling. Heat flux maps are obtained for pool boiling in FC-72 on a horizontal surface. Local heat flux variations are shown to be three to six times larger than variations in the spatially averaged heat flux.

  6. Rigid, Conjugated Macrocycles for High Performance Organic Photodetectors.

    Science.gov (United States)

    Zhang, Boyuan; Trinh, M Tuan; Fowler, Brandon; Ball, Melissa; Xu, Qizhi; Ng, Fay; Steigerwald, Michael L; Zhu, X-Y; Nuckolls, Colin; Zhong, Yu

    2016-12-21

    Organic photodetectors (OPDs) are attractive for their high optical absorption coefficient, broad wavelength tunability, and compatibility with lightweight and flexible devices. Here we describe a new molecular design that enables high performance organic photodetectors. We use a rigid, conjugated macrocycle as the electron acceptor in devices to obtain high photocurrent and low dark current. We make a direct comparison between the devices made with the macrocyclic acceptor and an acyclic control molecule; we find that the superior performance of the macrocycle originates from its rigid, conjugated, and cyclic structure. The macrocycle's rigid structure reduces the number of charged defects originating from deformed sp(2) carbons and covalent defects from photo/thermoactivation. With this molecular design, we are able to suppress dark current density while retaining high responsivity in an ultrasensitive nonfullerene OPD. Importantly, we achieve a detectivity of ∼10(14) Jones at near zero bias voltage. This is without the need for extra carrier blocking layers commonly employed in fullerene-based devices. Our devices are comparable to the best fullerene-based photodetectors, and the sensitivity at low working voltages (<0.1 V) is a record for nonfullerene OPDs.

  7. Performance of rotating drum biofilter for volatile organic compound removal at high organic loading rates

    Institute of Scientific and Technical Information of China (English)

    YANG Chunping; CHEN Hong; ZENG Guangming; ZHU Xueqing; SUIDAN Makram T

    2008-01-01

    Uneven distribution of volatile organic compounds (VOCs) and biomass,and excess biomass accumulation in some biofilters hinder the application of biofiltration technology.An innovative multilayer rotating drum biofilter (RDB) was developed to correct these problems.The RDB was operated at an empty bed contact time (EBCT) of 30 s and a rotational rate of 1.0 r/rain.Diethyl ether was chosen as the model VOC.Performance of the RDB was evaluated at organic loading rates of 32.1,64.2,128,and 256 g ether/(m3·h) (16.06 g ether/(m3·h) ≈1.0 kg chemical oxygen demand (COD)/(m3·d)).The EBCT and organic loading rates were recorded on the basis of the medium volume.Results show that the ether removal efficiency decreased with an increased VOC loading rate.Ether removal efficiencies exceeding 99% were achieved without biomass control even at a high VOC loading rate of 128 g ether/(m3·h). However,when the VOC loading rate was increased to 256 g ether/(m3·h),the average removal efficiency dropped to 43%.Nutrient limitation possibly contributed to the drop in ether removal efficiency.High biomass accumulation rate was also observed in the medium at the two higher ether loading rates,and removal of the excess biomass in the media was necessary to maintain stable performance. This work showed that the RDB is effective in the removal of diethyl ether from waste gas streams even at high organic loading rates. The results might help establish criteria for designing and operating RDBs.

  8. High quality transparent conductive electrodes in organic photovoltaic devices

    Energy Technology Data Exchange (ETDEWEB)

    Chakaroun, M. [XLIM Institute, UMR 6172, Universite de Limoges/CNRS, 123 Avenue Albert Thomas, 87060 Limoges (France); Lucas, B., E-mail: bruno.lucas@unilim.f [XLIM Institute, UMR 6172, Universite de Limoges/CNRS, 123 Avenue Albert Thomas, 87060 Limoges (France); Ratier, B. [XLIM Institute, UMR 6172, Universite de Limoges/CNRS, 123 Avenue Albert Thomas, 87060 Limoges (France); Defranoux, C.; Piel, J.P. [SOPRA-SA, 26 rue Pierre Joigneaux, 92270 Bois-Colombes (France); Aldissi, M. [XLIM Institute, UMR 6172, Universite de Limoges/CNRS, 123 Avenue Albert Thomas, 87060 Limoges (France)

    2009-12-15

    The use of indium tin oxide (ITO) in conjunction with polymeric substrates requires deposition at low temperatures or room temperature, and with a limited or no thermal treatment. This process results in high resistivity materials. To achieve practical resistivity levels, we replaced ITO, the workhorse in organic optoelectronic devices, with an ITO/Ag/ITO tri-layer anode. This material yielded the desired electrical properties without a significant effect on its optical properties. For example, a sheet resistance of 15 {Omega}/{open_square} and an optical transmission of 90% at 550 nm were obtained for a tri-layer film in which thickness of each ITO layer is 50 nm and the Ag layer thickness is 8 nm. The use of these tri-layer anodes in CuPc-C{sub 60}-based organic solar cells led to an increase in the fill factor under illumination, and thus an improvement of the external power conversion efficiency.

  9. High brightness diode-pumped organic solid-state laser

    CERN Document Server

    Zhao, Zhuang; Nafa, Malik; Chénais, Sébastien; Forget, Sébastien

    2015-01-01

    High-power, diffraction-limited organic solid-state laser operation has been achieved in a vertical external cavity surface-emitting organic laser (VECSOL), pumped by a low-cost compact blue laser diode. The diode-pumped VECSOLs were demonstrated with various dyes in a polymer matrix, leading to laser emissions from 540 nm to 660 nm. Optimization of both the pump pulse duration and output coupling leads to a pump slope efficiency of 11% for a DCM based VECSOLs. We report output pulse energy up to 280 nJ with 100 ns long pump pulses, leading to a peak power of 3.5 W in a circularly symmetric, diffraction-limited beam.

  10. High brightness diode-pumped organic solid-state laser

    Science.gov (United States)

    Zhao, Zhuang; Mhibik, Oussama; Nafa, Malik; Chénais, Sébastien; Forget, Sébastien

    2015-02-01

    High-power, diffraction-limited organic solid-state laser operation has been achieved in a vertical external cavity surface-emitting organic laser (VECSOL), pumped by a low-cost compact blue laser diode. The diode-pumped VECSOLs were demonstrated with various dyes in a polymer matrix, leading to laser emissions from 540 nm to 660 nm. Optimization of both the pump pulse duration and output coupling leads to a pump slope efficiency of 11% for a DCM based VECSOLs. We report output pulse energy up to 280 nJ with 100 ns long pump pulses, leading to a peak power of 3.5 W in a circularly symmetric, diffraction-limited beam.

  11. Solution-Processable Organic Molecule for High-Performance Organic Solar Cells with Low Acceptor Content.

    Science.gov (United States)

    Wang, Kun; Guo, Bing; Xu, Zhuo; Guo, Xia; Zhang, Maojie; Li, Yongfang

    2015-11-11

    A new planar D2-A-D1-A-D2 structured organic molecule with bithienyl benzodithiophene (BDT) as central donor unit D1 and fluorine-substituted benzothiadiazole (BTF) as acceptor unit and alkyl-dithiophene as end group and donor unit D2, BDT-BTF, was designed and synthesized for the application as donor material in organic solar cells (OSCs). BDT-BTF shows a broad absorption in visible region, suitable highest occupied molecular orbital energy level of -5.20 eV, and high hole mobility of 1.07 × 10(-2) cm(2)/(V s), benefitted from its high coplanarity and strong crystallinity. The OSCs based on BDT-BTF as donor (D) and PC71BM as acceptor (A) at a D/A weight ratio of 3:1 without any extra treatment exhibit high photovoltaic performance with Voc of 0.85 V, Jsc of 10.48 mA/cm(2), FF of 0.66, and PCE of 5.88%. The morphological study by transmission electron microscopy reveals that the blend of BDT-BTF and PC71BM (3:1, w/w) possesses an appropriate interpenetrating D/A network for the exciton separation and charge carrier transport, which agrees well with the good device performance. The optimized D/A weight ratio of 3:1 is the lowest acceptor content in the active layer reported so far for the high-performance OSCs, and the organic molecules with the molecular structure like BDT-BTF could be promising high-performance donor materials in solution-processable OSCs.

  12. CADASTER QSPR Models for Predictions of Melting and Boiling Points of Perfluorinated Chemicals.

    Science.gov (United States)

    Bhhatarai, Barun; Teetz, Wolfram; Liu, Tao; Öberg, Tomas; Jeliazkova, Nina; Kochev, Nikolay; Pukalov, Ognyan; Tetko, Igor V; Kovarich, Simona; Papa, Ester; Gramatica, Paola

    2011-03-14

    Quantitative structure property relationship (QSPR) studies on per- and polyfluorinated chemicals (PFCs) on melting point (MP) and boiling point (BP) are presented. The training and prediction chemicals used for developing and validating the models were selected from Syracuse PhysProp database and literatures. The available experimental data sets were split in two different ways: a) random selection on response value, and b) structural similarity verified by self-organizing-map (SOM), in order to propose reliable predictive models, developed only on the training sets and externally verified on the prediction sets. Individual linear and non-linear approaches based models developed by different CADASTER partners on 0D-2D Dragon descriptors, E-state descriptors and fragment based descriptors as well as consensus model and their predictions are presented. In addition, the predictive performance of the developed models was verified on a blind external validation set (EV-set) prepared using PERFORCE database on 15 MP and 25 BP data respectively. This database contains only long chain perfluoro-alkylated chemicals, particularly monitored by regulatory agencies like US-EPA and EU-REACH. QSPR models with internal and external validation on two different external prediction/validation sets and study of applicability-domain highlighting the robustness and high accuracy of the models are discussed. Finally, MPs for additional 303 PFCs and BPs for 271 PFCs were predicted for which experimental measurements are unknown. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Bubble Coalescence Heat Transfer During Subcooled Nucleate Pool Boiling

    Institute of Scientific and Technical Information of China (English)

    Abdoulaye Coulibaly; LIN Xipeng; Bi Jingliang; David M Christopher

    2012-01-01

    Bubble coalescence during subcooled nucleate pool boiling was investigated experimentally using constant wall temperature boundary conditions while the wall heat flux was measured at a various locations to understand the effects of coalescence on the heat transfer. The observations showed that the coalesced bubble moved and oscillated on the heater surface with significant heat transfer variations prior to departure. Some observations also showed coalescence with no increase in the heat transfer rate. The heat flux for boiling with coalescence fluctuated much more than for single bubble boiling due to the vaporization of the liquid layer trapped between the bubbles.

  14. Boiling Heat Transfer on Porous Surfaces with Vapor Channels

    Institute of Scientific and Technical Information of China (English)

    吴伟; 杜建华; 王补宣

    2002-01-01

    Boiling heat transfer on porous coated surfaces with vapor channels was investigated experimentally to determine the effects of the size and density of the vapor channels on the boiling heat transfer. Observations showed that bubbles escaping from the channels enhanced the heat transfer. Three regimes were identified: liquid flooding, bubbles in the channel and the bottom drying out region. The maximum heat transfer occurred for an optimum vapor channel density and the boiling heat transfer performance was increased if the channels were open to the bottom of the porous coating.

  15. Modeling of Heat Exchange with Developed Nucleate Boiling on Tenons

    Directory of Open Access Journals (Sweden)

    A. V. Оvsiannik

    2007-01-01

    Full Text Available The paper proposes a thermal and physical model for heat exchange processes with developed nucleate boiling on the developed surfaces (tenons with various contours of heat transfer surface. Dependences for calculating convective heat exchange factor have been obtained on the basis of modeling representation. Investigations have shown that an intensity of convective heat exchange does not depend on tenon profile when boiling takes place on the tenons. The intensity is determined by operating conditions, thermal and physical properties of liquid, internal characteristics of boiling processes and geometrical characteristics of a tenon.

  16. Models and Stability Analysis of Boiling Water Reactors

    Energy Technology Data Exchange (ETDEWEB)

    John Dorning

    2002-04-15

    We have studied the nuclear-coupled thermal-hydraulic stability of boiling water reactors (BWRs) using a model that includes: space-time modal neutron kinetics based on spatial w-modes; single- and two-phase flow in parallel boiling channels; fuel rod heat conduction dynamics; and a simple model of the recirculation loop. The BR model is represented by a set of time-dependent nonlinear ordinary differential equations, and is studied as a dynamical system using the modern bifurcation theory and nonlinear dynamical systems analysis. We first determine the stability boundary (SB) - or Hopf bifurcation set- in the most relevant parameter plane, the inlet-subcooling-number/external-pressure-drop plane, for a fixed control rod induced external reactivity equal to the 100% rod line value; then we transform the SB to the practical power-flow map used by BWR operating engineers and regulatory agencies. Using this SB, we show that the normal operating point at 100% power is very stable, that stability of points on the 100% rod line decreases as the flow rate is reduced, and that operating points in the low-flow/high-power region are least stable. We also determine the SB that results when the modal kinetics is replaced by simple point reactor kinetics, and we thereby show that the first harmonic mode does not have a significant effect on the SB. However, we later show that it nevertheless has a significant effect on stability because it affects the basin of attraction of stable operating points. Using numerical simulations we show that, in the important low-flow/high-power region, the Hopf bifurcation that occurs as the SB is crossed is subcritical; hence, growing oscillations can result following small finite perturbations of stable steady-states on the 100% rod line at points in the low-flow/high-power region. Numerical simulations are also performed to calculate the decay ratios (DRs) and frequencies of oscillations for various points on the 100% rod line. It is

  17. Genotoxicity studies in the ST cross of the Drosophila wing spot test of sunflower and soybean oils before and after frying and boiling procedures.

    Science.gov (United States)

    Demir, Eşref; Marcos, Ricard; Kaya, Bülent

    2012-10-01

    Sunflower and soybean oils were tested for genotoxicity in the Drosophila wing somatic mutation and recombination assay. Results indicate that both oils produce genotoxic effects when tested without any previous frying or boiling processes. Boiling sunflower oil during fifteen, thirty and sixty minutes significantly increased its genotoxic response; nevertheless, after frying potatoes this oil showed a significant decrease in the genotoxic activity. On the other hand, boiling and frying soybean oil in the same conditions results in a decrease of its genotoxic potential. We have also detected that the amount of total polar materials increases significantly in oils submitted to frying or boiling process. Nevertheless, in oils obtained after frying potatoes, the amount of TPM was higher than after boiling. It is suggested that this effect is probably due to the amount of non-volatile TPM, the fatty acid composition of the oils, the types of frying oil, the high frying temperature and time, and the number of boiling and frying. This is the first study reporting genotoxicity data in Drosophila for the boiling and frying of both sunflower and soybean oils. Copyright © 2012 Elsevier Ltd. All rights reserved.

  18. Governing metal-organic frameworks towards high stability.

    Science.gov (United States)

    Li, Na; Xu, Jian; Feng, Rui; Hu, Tong-Liang; Bu, Xian-He

    2016-06-30

    Metal-organic frameworks (MOFs) constructed with metal ions/clusters and organic ligands have emerged as an important family of porous materials for various applications. However, the stability of this class of materials is crucial for their practical applications, which might be improved by varying their chemical composition and/or structurally tuning them. To fabricate MOFs with high stability, several strategies for enhancing the stability of MOFs have been developed, in which the strength of metal-ligand bonds is especially considered: the use of highly charged cations and higher pKa ligands, and varying the chemical functionality of linkers. On the other hand, the regulation of their structural architectures is also investigated: interpenetrated frameworks, multi-walled frameworks, and self-strengthening of the frameworks. In addition, the surface modification can also improve the stability of the materials. In this review, we introduce and summarize these strategies from the viewpoint of structural tuning and component choosing, providing useful instructions for the further design and synthesis of MOFs with high-level stability.

  19. Highly stable organic fluorescent nanorods for living- cell imaging

    Institute of Scientific and Technical Information of China (English)

    Minhuan Lan[1,3; Jinfeng Zhang[1,3; Xiaoyue Zhu[1; Pengfei Wang[2; Xianfeng Chen[1; Chun-Sing Lee[1; Wenjun Zhang[1

    2015-01-01

    Metal-free, organic-dye-based fluorescent nanorods were fabricated through a simple solvent-exchange procedure. The as-prepared nanorods exhibit low toxicity to living cells and excellent photostability. Furthermore, they are stable in solutions of various pHs and high ionic strength and in solutions with interfering metal ions. Compared with the free DPP-Br molecules in THF, these nanorods exhibit larger Stokes shift, broader absorption spectra, and greatly improved photostability. We successfully demonstrated the application of the nanorods, including their aforementioned beneficial characteristics, as a good fluorescence probe for bio-imaging.

  20. High Methane Storage Capacity in Aluminum Metal–Organic Frameworks

    OpenAIRE

    Gándara, Felipe; Furukawa, Hiroyasu; Lee, Seungkyu; Yaghi, Omar M.

    2014-01-01

    The use of porous materials to store natural gas in vehicles requires large amounts of methane per unit of volume. Here we report the synthesis, crystal structure and methane adsorption properties of two new aluminum metal–organic frameworks, MOF-519 and MOF-520. Both materials exhibit permanent porosity and high methane volumetric storage capacity: MOF-519 has a volumetric capacity of 200 and 279 cm3 cm–3 at 298 K and 35 and 80 bar, respectively, and MOF-520 has a volumetric capacity of 162 ...

  1. 40 CFR 180.1056 - Boiled linseed oil; exemption from requirement of tolerance.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Boiled linseed oil; exemption from... From Tolerances § 180.1056 Boiled linseed oil; exemption from requirement of tolerance. Boiled linseed... “boiled linseed oil.” This exemption is limited to use on rice before edible parts form. ...

  2. Zero Boil Off System for Cryogen Storage Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This work proposes to develop a zero boil off (ZBO) dewar using a two-stage pulse-tube cooler together with two innovative, continuous-flow cooling loops and an...

  3. Boiling local heat transfer enhancement in minichannels using nanofluids.

    Science.gov (United States)

    Chehade, Ali Ahmad; Gualous, Hasna Louahlia; Le Masson, Stephane; Fardoun, Farouk; Besq, Anthony

    2013-03-18

    This paper reports an experimental study on nanofluid convective boiling heat transfer in parallel rectangular minichannels of 800 μm hydraulic diameter. Experiments are conducted with pure water and silver nanoparticles suspended in water base fluid. Two small volume fractions of silver nanoparticles suspended in water are tested: 0.000237% and 0.000475%. The experimental results show that the local heat transfer coefficient, local heat flux, and local wall temperature are affected by silver nanoparticle concentration in water base fluid. In addition, different correlations established for boiling flow heat transfer in minichannels or macrochannels are evaluated. It is found that the correlation of Kandlikar and Balasubramanian is the closest to the water boiling heat transfer results. The boiling local heat transfer enhancement by adding silver nanoparticles in base fluid is not uniform along the channel flow. Better performances and highest effect of nanoparticle concentration on the heat transfer are obtained at the minichannels entrance.

  4. Boiling of HFE-7100 on a Straight Pin Fin

    Institute of Scientific and Technical Information of China (English)

    Z. W. Liu; W.W. Lin; D.J. Lee; J.P. Hsu

    2001-01-01

    This paper deals with an experimental investigation of pin fin boiling of saturated and subcooled HFE-7100 under atmospheric pressure. Fin base temperature and heat flux data are measured along with the fin tip temperature. The basic features of boiling stability of HFE-7100 boiling on pin fin had been reported for the first time. For a given liquid/heating surface combination there exist upper steady-state (USS) branch and lower steady-state (LSS)branch, and a large, unstable regime located in between. Zones with different stability characteristics are mapped according to boiling on fins with different aspect ratios. Liquid subcooling can largely enhance heat transfer performance. A longer fin can provide a safer operation.

  5. Self-Sustaining Thorium Boiling Water Reactors

    Directory of Open Access Journals (Sweden)

    Ehud Greenspan

    2012-10-01

    Full Text Available A thorium-fueled water-cooled reactor core design approach that features a radially uniform composition of fuel rods in stationary fuel assembly and is fuel-self-sustaining is described. This core design concept is similar to the Reduced moderation Boiling Water Reactor (RBWR proposed by Hitachi to fit within an ABWR pressure vessel, with the following exceptions: use of thorium instead of depleted uranium for the fertile fuel; elimination of the internal blanket; and elimination of absorbers from the axial reflectors, while increasing the length of the fissile zone. The preliminary analysis indicates that it is feasible to design such cores to be fuel-self-sustaining and to have a comfortably low peak linear heat generation rate when operating at the nominal ABWR power level of nearly 4000 MWth. However, the void reactivity feedback tends to be too negative, making it difficult to have sufficient shutdown reactivity margin at cold zero power condition. An addition of a small amount of plutonium from LWR used nuclear fuel was found effective in reducing the magnitude of the negative void reactivity effect and enables attaining adequate shutdown reactivity margin; it also flattens the axial power distribution. The resulting design concept offers an efficient incineration of the LWR generated plutonium in addition to effective utilization of thorium. Additional R&D is required in order to arrive at a reliable practical and safe design.

  6. Experimental study of multi-scale heat transfer characteristics at pool boiling

    Science.gov (United States)

    Serdyukov, V.; Surtaev, A.

    2017-01-01

    This study presents the results of the experimental investigation of local and integral characteristics of heat transfer at liquid pool boiling. Saturated ethanol and water were used as the working fluids. Thin, resistively heated indium-tin oxide films deposited onto the sapphire substrates were used as the heaters. The synchronized measurements of the heater surface temperature field and dynamics of vapor bubbles were performed by high-speed infrared thermography with the frame rate of 1000 fps and resolution of up to 0.13 μm/px and high-speed video recording. In this paper new data on major local boiling characteristics, such as nucleation site density, dynamics of vapor bubbles, temporal characteristics and nucleation frequency at different heat fluxes and superheating and their comparison with correlations are presented.

  7. Organ and tissue donation: what do high school students know?

    Directory of Open Access Journals (Sweden)

    Marcela Cristina de Lemos

    2007-09-01

    Full Text Available Objectives: To know the opinion of senior high school students in publicand private schools on the process of donating and transplanting organsand tissues, and their desire to be donors. Methods: A descriptive crosssectionalstudy, conducted from 2004 to 2005, on the opinion/knowledgeof senior high school students in public and private schools in the VilaMariana region of the city of São Paulo, on the process of organ and tissuedonation and transplantation. The convenience sample was made up of140 (81% students from two private schools and 167 (51% studentsfrom a public school. The project was approved by the Research EthicsCommittee of the UNIFESP. Results: Data showed that 163 (53.1%students believe that donation is by presumed consent and 147 (47.9%that consider that it occurs by informed consent. Of the public schoolstudents, 120 (71.9% believe that transplants are public and free ofcharge in Brazil versus 94 (67.1% of the students from private schools.Students know that donations may be made by living or dead donors(121 - 86.4% private schools versus 113 – 67.7% public school. Wehighlight that 22 (15.7% of the private school students and 16 (9.6%of those from the public school believe that the commerce of organs isallowed in Brazil. As to intentions of being a donor, 108 (77.1% of theprivate school students declared themselves organ and tissue donorsversus 106 (63.5% from the public school, and 63 (59.4% from thepublic versus 61 (56.5% from the private schools have already informedtheir families. Conclusion: There was no difference in knowledge andopinion among the students from the public and private schools as toaspects regarding donation and transplantation.

  8. Correlations estimate volume distilled using gravity, boiling point

    Energy Technology Data Exchange (ETDEWEB)

    Moreno, A.; Consuelo Perez de Alba, M. del; Manriquez, L.; Guardia Mendoz, P. de la [Inst. Mexicano del Petroleo, Mexico City (Mexico)

    1995-10-23

    Mathematical nd graphic correlations have been developed for estimating cumulative volume distilled as a function of crude API gravity and true boiling point (TBP). The correlations can be used for crudes with gravities of 21--34{degree} API and boiling points of 150--540 C. In distillation predictions for several mexican and Iraqi crude oils, the correlations have exhibited accuracy comparable to that of laboratory measurements. The paper discusses the need for such a correlation and the testing of the correlation.

  9. Taylor stability of viscous fluids with application to film boiling

    Science.gov (United States)

    Dhir, V. K.; Lienhard, J. H.

    1973-01-01

    The dispersion relation is evaluated numerically for Taylor waves in a viscous unstable interface with surface tension. The solution takes account of transverse curvature and the numerical evaluations apply to horizontal cylindrical, as well as to plane, interfaces. The result is verified with frequency and wavelength data obtained during film boiling on horizontal wires. A very general empirical correlation is given, en passant, for the vapor blanket thickness during film boiling.

  10. Nucleate Boiling Heat Transfer Studied Under Reduced-Gravity Conditions

    Science.gov (United States)

    Chao, David F.; Hasan, Mohammad M.

    2000-01-01

    Boiling is known to be a very efficient mode of heat transfer, and as such, it is employed in component cooling and in various energy-conversion systems. In space, boiling heat transfer may be used in thermal management, fluid handling and control, power systems, and on-orbit storage and supply systems for cryogenic propellants and life-support fluids. Recent interest in the exploration of Mars and other planets and in the concept of in situ resource utilization on the Martian and Lunar surfaces highlights the need to understand how gravity levels varying from the Earth's gravity to microgravity (1g = or > g/g(sub e) = or > 10(exp -6)g) affect boiling heat transfer. Because of the complex nature of the boiling process, no generalized prediction or procedure has been developed to describe the boiling heat transfer coefficient, particularly at reduced gravity levels. Recently, Professor Vijay K. Dhir of the University of California at Los Angeles proposed a novel building-block approach to investigate the boiling phenomena in low-gravity to microgravity environments. This approach experimentally investigates the complete process of bubble inception, growth, and departure for single bubbles formed at a well-defined and controllable nucleation site. Principal investigator Professor Vijay K. Dhir, with support from researchers from the NASA Glenn Research Center at Lewis Field, is performing a series of pool boiling experiments in the low-gravity environments of the KC 135 microgravity aircraft s parabolic flight to investigate the inception, growth, departure, and merger of bubbles from single- and multiple-nucleation sites as a function of the wall superheat and the liquid subcooling. Silicon wafers with single and multiple cavities of known characteristics are being used as test surfaces. Water and PF5060 (an inert liquid) were chosen as test liquids so that the role of surface wettability and the magnitude of the effect of interfacial tension on boiling in reduced

  11. Biogas production from substrates with high amounts of organic nitrogen

    Energy Technology Data Exchange (ETDEWEB)

    Prechtl, S.; Faulstich, M. [ATZ-EVUS Development Center for Process Engineering, Sulzbach-Rosenberg (Germany)

    2004-07-01

    Thermophilic fermentation is a favoured method for treating animal by-products because of its short hydraulic retention time and hygienic features. However, substrates with high organic nitrogen content can create problems in the fermentation process due to the high ammonium concentration produced during anaerobic degradation. More economical and ecological solutions for treating animal by-products are also needed to address concerns of the Bovine Spongiform Encephalopathy (BSE) crisis. This study considered a recycling concept based on the Thermal Pressure Hydrolysis (TPH) process with subsequent anaerobic digestion. A heat exchange system was also developed. The sterilization in the TPH reactor guarantees complete disinfection. The study examined the reactor temperature, pH-value, hydraulic retention time, organic loading rate and degradation performance. The amount of volatile fatty acids in the effluent of the anaerobic reactor suggests good biological degradation. A combined heat and power station with an electrical efficiency of 38 per cent made it possible to produce up to 780 kWh of electricity from 1,000 kg of raw material. 6 refs., 2 tabs., 1 fig.

  12. Influence of Boiling Duration of GCSB-5 on Index Compound Content and Antioxidative and Anti-inflammatory Activity.

    Science.gov (United States)

    Lee, In-Hee; Chung, Hwa-Jin; Shin, Joon-Shik; Ha, In-Hyuk; Kim, Me-Riong; Koh, Wonil; Lee, Jinho

    2017-01-01

    GCSB-5, an herbal drug composition with an anti-inflammatory effect, is prepared by boiling, which is the most common herbal extraction method in traditional Korean medicine. Several parameters are involved in the process, i.e., extractant type, herb-to-extractant ratio, extraction temperature and pressure, and total boiling time. The aim of this study was to examine the influence of boiling time on index compound amount and the antioxidative and anti-inflammatory activities of GCSB-5. Different samples of GCSB-5 were obtained by decocting for 30, 60, 90, 120, 150, and 240 min. Each sample was tested for hydrogen ion concentration (pH), total soluble solid content (TSSC), marker compound profiles, and antioxidative and anti-inflammatory activity. pH was found to decrease while TSSC increased with extended decoction. Marker compound contents for GCSB-5 (acanthoside D for Acanthopanax sessiliflorus Seem, 20-hydroxyecdysone for Achyranthes japonica Nakai, and pinoresinol diglucoside for Eucommia ulmoides Oliver) remained relatively constant regardless of the length of boiling. Total D-glucose amount increased with longer boiling. The antioxidative and anti-inflammatory potentials of GCSB-5 were not substantially affected by decoction duration. Biological characteristics and marker compound content of GCSB-5 were not altered significantly in prolonged boiling. Longer boiling duration of GCSB-5 did not increase yield in a time-dependent manner, but yields of 210 and 240 min samples were significantly higherHydrogen ion concentration of GCSB-5 samples decreased while total soluble solid content and D-glucose concentration levels increased with boiling durationAlthough concentrations of some index compounds increased with extended boiling duration of GCSB-5, increase was small and not in a direct proportional relationshipAntioxidative and anti-inflammatory properties of GCSB-5 were not substantially affected by decoction duration. Abbreviations used: CAM: Complementary

  13. Infrared thermometry study of nanofluid pool boiling phenomena

    Directory of Open Access Journals (Sweden)

    Hu Lin-wen

    2011-01-01

    Full Text Available Abstract Infrared thermometry was used to obtain first-of-a-kind, time- and space-resolved data for pool boiling phenomena in water-based nanofluids with diamond and silica nanoparticles at low concentration (<0.1 vol.%. In addition to macroscopic parameters like the average heat transfer coefficient and critical heat flux [CHF] value, more fundamental parameters such as the bubble departure diameter and frequency, growth and wait times, and nucleation site density [NSD] were directly measured for a thin, resistively heated, indium-tin-oxide surface deposited onto a sapphire substrate. Consistent with other nanofluid studies, the nanoparticles caused deterioration in the nucleate boiling heat transfer (by as much as 50% and an increase in the CHF (by as much as 100%. The bubble departure frequency and NSD were found to be lower in nanofluids compared with water for the same wall superheat. Furthermore, it was found that a porous layer of nanoparticles built up on the heater surface during nucleate boiling, which improved surface wettability compared with the water-boiled surfaces. Using the prevalent nucleate boiling models, it was possible to correlate this improved surface wettability to the experimentally observed reductions in the bubble departure frequency, NSD, and ultimately to the deterioration in the nucleate boiling heat transfer and the CHF enhancement.

  14. Infrared thermometry study of nanofluid pool boiling phenomena.

    Science.gov (United States)

    Gerardi, Craig; Buongiorno, Jacopo; Hu, Lin-Wen; McKrell, Thomas

    2011-03-16

    Infrared thermometry was used to obtain first-of-a-kind, time- and space-resolved data for pool boiling phenomena in water-based nanofluids with diamond and silica nanoparticles at low concentration (heat transfer coefficient and critical heat flux [CHF] value, more fundamental parameters such as the bubble departure diameter and frequency, growth and wait times, and nucleation site density [NSD] were directly measured for a thin, resistively heated, indium-tin-oxide surface deposited onto a sapphire substrate. Consistent with other nanofluid studies, the nanoparticles caused deterioration in the nucleate boiling heat transfer (by as much as 50%) and an increase in the CHF (by as much as 100%). The bubble departure frequency and NSD were found to be lower in nanofluids compared with water for the same wall superheat. Furthermore, it was found that a porous layer of nanoparticles built up on the heater surface during nucleate boiling, which improved surface wettability compared with the water-boiled surfaces. Using the prevalent nucleate boiling models, it was possible to correlate this improved surface wettability to the experimentally observed reductions in the bubble departure frequency, NSD, and ultimately to the deterioration in the nucleate boiling heat transfer and the CHF enhancement.

  15. High-Performance Long-Term-Stable Dopant-Free Perovskite Solar Cells and Additive-Free Organic Solar Cells by Employing Newly Designed Multirole π-Conjugated Polymers.

    Science.gov (United States)

    Kranthiraja, Kakaraparthi; Gunasekar, Kumarasamy; Kim, Hyunji; Cho, An-Na; Park, Nam-Gyu; Kim, Seonha; Kim, Bumjoon J; Nishikubo, Ryosuke; Saeki, Akinori; Song, Myungkwan; Jin, Sung-Ho

    2017-06-01

    Perovskite solar cells (PSCs) and organic solar cells (OSCs) are promising renewable light-harvesting technologies with high performance, but the utilization of hazardous dopants and high boiling additives is harmful to all forms of life and the environment. Herein, new multirole π-conjugated polymers (P1-P3) are developed via a rational design approach through theoretical hindsight, further successfully subjecting them into dopant-free PSCs as hole-transporting materials and additive-free OSCs as photoactive donors, respectively. Especially, P3-based PSCs and OSCs not only show high power conversion efficiencies of 17.28% and 8.26%, but also display an excellent ambient stability up to 30 d (for PSCs only), owing to their inherent superior optoelectronic properties in their pristine form. Overall, the rational approach promises to support the development of environmentally and economically sustainable PSCs and OSCs. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Neutralized wettability effect of superhydrophilic Cr-layered surface on pool boiling critical heat flux

    Energy Technology Data Exchange (ETDEWEB)

    Son, Hong Hyun; Jeong, Ui Ju; Seo, Gwang Hyeok; Jeun, Gyoo Dong; Kim, Sung Joong [KAERI, Daejeon (Korea, Republic of)

    2016-05-15

    The former method is deemed challenging due to longer development period and license issue. In this regard, FeCrAl, Cr, and SiC have been received positive attention as ATF coating materials because they are highly resistant to high temperature steam reaction causing massive hydrogen generation. In this study, Cr was selected as a target deposition material on the metal substrate because we found that Cr-layered surface becomes superhydrophilic, favorable to delaying the triggering of the critical heat flux (CHF). Thus in order to investigate the effect of Cr-layered superhydrophilic surfaces (under explored coating conditions) on pool boiling heat transfer, pool boiling experiment was conducted in the saturated deionized water under atmospheric pressure. As a physical vapor deposition (PVD) method, the DC magnetron sputtering technique was introduced to develop Cr-layered nanostructure. As a control variable of DC sputtering, substrate temperature was selected. Surface wettability and nanostructure were analyzed as major surface parameters on the CHF. We believe that highly dense micro/nano structure without nucleation cavities and inner pores neutralized the wettability effect on the CHF. Moreover, superhydrophilic surface with deficient cavity density rather hinders active nucleation. This emphasizes the importance of micro/nano structure surface for enhanced boiling heat transfer.

  17. Entropy generation analysis for film boiling: A simple model of quenching

    Science.gov (United States)

    Lotfi, Ali; Lakzian, Esmail

    2016-04-01

    In this paper, quenching in high-temperature materials processing is modeled as a superheated isothermal flat plate. In these phenomena, a liquid flows over the highly superheated surfaces for cooling. So the surface and the liquid are separated by the vapor layer that is formed because of the liquid which is in contact with the superheated surface. This is named forced film boiling. As an objective, the distribution of the entropy generation in the laminar forced film boiling is obtained by similarity solution for the first time in the quenching processes. The PDE governing differential equations of the laminar film boiling including continuity, momentum, and energy are reduced to ODE ones, and a dimensionless equation for entropy generation inside the liquid boundary and vapor layer is obtained. Then the ODEs are solved by applying the 4th-order Runge-Kutta method with a shooting procedure. Moreover, the Bejan number is used as a design criterion parameter for a qualitative study about the rate of cooling and the effects of plate speed are studied in the quenching processes. It is observed that for high speed of the plate the rate of cooling (heat transfer) is more.

  18. RUBI -a Reference mUltiscale Boiling Investigation for the Fluid Science Laboratory

    Science.gov (United States)

    Schweizer, Nils; Stelzer, Marco; Schoele-Schulz, Olaf; Picker, Gerold; Ranebo, Hans; Dettmann, Jan; Minster, Olivier; Toth, Balazs; Winter, Josef; Tadrist, Lounes; Stephan, Peter; Grassi, Walter; di Marco, Paolo; Colin, Catherine; Piero Celata, Gian; Thome, John; Kabov, Oleg

    Boiling is a two-phase heat transfer process where large heat fluxes can be transferred with small driving temperature differences. The high performance of boiling makes the process very interesting for heat transfer applications and it is widely used in industry for example in power plants, refrigeration systems, and electronics cooling. Nevertheless, due to the large number of involved phenomena and their often highly dynamic nature a fundamental understanding and closed theoretical description is not yet accomplished. The design of systems incorporating the process is generally based on empirical correlations, which are commonly accompanied by large uncertainties and, thus, has to be verified by expensive test campaigns. Hence, strong efforts are currently made to develop applicable numerical tools for a reliable prediction of the boiling heat transfer performance and limits. In order to support and validate this development and, in particular as a precondition, to enhance the basic knowledge about boiling the comprehensive multi-scale experiment RUBI (Reference mUlti-scale Boiling Investigation) for the Fluid Science Laboratory on board the ISS is currently in preparation. The scientific objectives and requirements of RUBI have been defined by the members of the ESA topical team "Boiling and Multiphase Flow" and addresses fundamental aspects of boiling phenomena. The main objectives are the measurement of wall temperature and heat flux distribution underneath vapour bubbles with high spatial and tem-poral resolution by means of IR thermography accompanied by the synchronized high-speed observation of the bubble shapes. Furthermore, the fluid temperature in the vicinity and inside of the bubbles will be measured by a micro sensor array. Additional stimuli are the generation of an electric field above the heating surface and a shear flow created by a forced convection loop. The objective of these stimuli is to impose forces on the bubbles and investigate the

  19. Boiling Heat Transfer Mechanisms in Earth and Low Gravity: Boundary Condition and Heater Aspect Ratio Effects

    Science.gov (United States)

    Kim, Jungho

    2004-01-01

    Boiling is a complex phenomenon where hydrodynamics, heat transfer, mass transfer, and interfacial phenomena are tightly interwoven. An understanding of boiling and critical heat flux in microgravity environments is of importance to space based hardware and processes such as heat exchange, cryogenic fuel storage and transportation, electronic cooling, and material processing due to the large amounts of heat that can be removed with relatively little increase in temperature. Although research in this area has been performed in the past four decades, the mechanisms by which heat is removed from surfaces in microgravity are still unclear. Recently, time and space resolved heat transfer data were obtained in both earth and low gravity environments using an array of microheaters varying in size between 100 microns to 700 microns. These heaters were operated in both constant temperature as well as constant heat flux mode. Heat transfer under nucleating bubbles in earth gravity were directly measured using a microheater array with 100 m resolution operated in constant temperature mode with low and high subcooled bulk liquid along with images from below and from the side. The individual bubble departure diameter and energy transfer were larger with low subcooling but the departure frequency increased at high subcooling, resulting in higher overall heat transfer. The bubble growth for both subcoolings was primarily due to energy transfer from the superheated liquid layer relatively little was due to wall heat transfer during the bubble growth process. Oscillating bubbles and sliding bubbles were also observed in highly subcooled boiling. Transient conduction and/or microconvection was the dominant heat transfer mechanism in the above cases. A transient conduction model was developed and compared with the experimental data with good agreement. Data was also obtained with the heater array operated in a constant heat flux mode and measuring the temperature distribution across

  20. Void fraction prediction in saturated flow boiling

    Energy Technology Data Exchange (ETDEWEB)

    Francisco J Collado [Dpto de Ingenieria Mecanica-Motores Termicos, CPS-B, Universidad de Zaragoza, Maria de Luna 50018-Zaragoza (Spain)

    2005-07-01

    Full text of publication follows: An essential element in thermal-hydraulics is the accurate prediction of the vapor void fraction, or fraction of the flow cross-sectional area occupied by steam. Recently, the author has suggested to calculate void fraction working exclusively with thermodynamic properties. It is well known that the usual 'flow' quality, merely a mass flow rate ratio, is not at all a thermodynamic property because its expression in function of thermodynamic properties includes the slip ratio, which is a parameter of the process not a function of state. By the other hand, in the classic and well known expression of the void fraction - in function of the true mass fraction of vapor (also called 'static' quality), and the vapor and liquid densities - does not appear the slip ratio. Of course, this would suggest a direct procedure for calculating the void fraction, provided we had an accurate value of the true mass fraction of vapor, clearly from the heat balance. However the classic heat balance is usually stated in function of the 'flow' quality, what sounds really contradictory because this parameter, as we have noted above, is not at all a thermodynamic property. Then we should check against real data the actual relationship between the thermodynamic properties and the applied heat. For saturated flow boiling just from the inlet of the heated tube, and not having into account the kinetic and potential terms, the uniform applied heat per unit mass of inlet water and per unit length (in short, specific linear heat) should be closely related to a (constant) slope of the mixture enthalpy. In this work, we have checked the relation between the specific linear heat and the thermodynamic enthalpy of the liquid-vapor mixture using the actual mass fraction. This true mass fraction is calculated using the accurate measurements of the outlet void fraction taken during the Cambridge project by Knights and Thom in the sixties for

  1. High exposures to organic solvents among graffiti removers.

    Science.gov (United States)

    Anundi, H; Lind, M L; Friis, L; Itkes, N; Langworth, S; Edling, C

    1993-01-01

    The exposure to organic solvents among 12 graffiti removers was studied. Health effects were also assessed by structured interview and a symptom questionnaire. Blood and urine samples were collected at the end of the day of air sampling. The concentrations of dichloromethane, glycol ethers, trimethylbenzenes and N-methyl-2-pyrrolidinone in the breathing zone of each worker were measured during one working day. The 8-h time-weighted average exposure to dichloromethane ranged from 18 to 1200 mg/m3. The Swedish Permissible Exposure Limit value for dichloromethane is 120 mg/m3. The air concentrations of glycol ethers, trimethylbenzenes and N-methyl-2-pyrrolidinone were low or not detectable. No exposure-related deviations in the serum concentrations of creatinine, aspartate transaminase, alanine transaminase, gamma-glutamyl transpeptidase or hyaluronan or the urine concentrations of alpha 1-microglobulin, beta 2-microglobulin or N-acetyl-beta-glucosaminidase were found. Irritative symptoms of the eyes and upper respiratory tract were more prevalent than in the general population. This study demonstrates that old knowledge about work hazards is not automatically transferred to new professions. Another aspect is that the public is also exposed as the job is performed during daytime in underground stations. At least for short periods, bystanders may be exposed to high concentrations of organic solvent vapours. People with predisposing conditions, e.g. asthmatics, may risk adverse reactions.

  2. Observation of Boiling Structure and CHF Phenomena between Parallel Vertical Plates Submerged in a Pool

    Energy Technology Data Exchange (ETDEWEB)

    Chu, In-Cheol; Euh, Dong Jin; Song, Chul-Hwa [KAERI, Daejeon (Korea, Republic of)

    2015-05-15

    The dynamic behavior of dry areas or phase distribution on the heating surface were observed by total reflection technique and DEPIcT. Instantaneous two-dimensional temperature distribution of a boiling surface was measured by infrared thermometry. These studies reported that the key physics of the CHF triggering mechanism was the dynamic behavior of the dry area under the massive bubble hovering on a surface and the appearance of a non-rewetting dry area. The gap between parallel vertical fuel plates ranges from 2 to 3 mm, typically for the research reactors. In addition, boiling in a confined narrow channel is encountered in high-performance heat exchangers and electronics component cooling. The CHF value for a vertical plate in a pool is strongly affected by the existence of the narrow confinement. However, the studies to identify the local boiling structure on a heating surface and CHF mechanism for this kind of geometry are quite lacking. In this study, CHF phenomena as well as global and local boiling structures near a heating surface were observed for a vertical narrow channel submerged in a pool, using total reflection and shadow graph visualization techniques. In-depth visualization studies were made to observe the global and local boiling structures, dynamic behavior of the dry area, and its rewetting process in a vertical narrow channel submerged in a pool of saturated Freon R-113. Based on this observation, new CHF mechanism was suggested for the present boiling configuration. The periodic feature of a slug flow prevailed above the heat flux of 77.2% CHF. The heating surface under the slug bubble was almost dry, but this large dry patch was effectively rewetted as the slug tail region rushed into the region covered by the slug bubble. The dry area fraction in the slug tail region increased gradually with an increase in the heat flux, and the rewetting efficiency of the slug tail region became deteriorated due to an enhancement of bubble nucleation

  3. Heat transfer mechanisms in microgravity flow boiling.

    Science.gov (United States)

    Ohta, Haruhiko

    2002-10-01

    The objective of this paper is to clarify the mechanisms of heat transfer and dryout phenomena in flow boiling under microgravity conditions. Liquid-vapor behavior in annular flow, encountered in the moderate quality region, has extreme significance for practical application in space. To clarify the gravity effect on the heat transfer observed for an upward flow in a tube, the research described here started from the measurement of pressure drop for binary gas-liquid mixture under various gravity conditions. The shear stress acting on the surface of the annular liquid film was correlated by an empirical method. Gravity effects on the heat transfer due to two-phase forced convection were investigated by the analysis of velocity and temperature profiles in the film. The results reproduce well the trends of heat transfer coefficients varying with the gravity level, quality, and mass velocity. Dryout phenomena in the moderate quality region were observed in detail by the introduction of a transparent heated tube. At heat fluxes just lower and higher than CHF value, a transition of the heat transfer coefficient was calculated from oscillating wall temperature, where a series of opposing heat transfer trends--the enhancement due to the quenching of dried areas or evaporation from thin liquid films and the deterioration due to the extension of dry patches--were observed between the passage of disturbance waves. The CHF condition that resulted from the insufficient decrease of wall temperature in the period of enhanced heat transfer was overcome by a temperature increase in the deterioration period. No clear effect of gravity on the mechanisms of dryout was observed within the range of experiments.

  4. Studying heat transfer enhancement for water boiling on a surface with micro- and nanorelief

    Science.gov (United States)

    Kuzma-Kichta, Yu. A.; Lavrikov, A. V.; Shustov, M. V.; Chursin, P. S.; Chistyakova, A. V.; Zvonarev, Yu. A.; Zhukov, V. M.; Vasil'eva, L. T.

    2014-03-01

    We present the results from a study of heat transfer enhancement for bulk water boiling at atmospheric pressure on a surface with micro- and nanorelief, including a relief formed from silicon carbide and aluminum oxide nanoparticles. Horizontally oriented steel tube 1.2 mm in diameter and copper plate 15 × 3 mm in size were selected as test sections. The process was recorded by means of a video camera, and the values of heat transfer, critical heat fluxes, and contact angles were measured. The use of surface with micro- and nanorelief makes it possible to obtain a significantly higher critical heat flux and boiling heat transfer coefficient owing to a change of surface wettability. The results of investigations can find use in compact heat exchangers, refrigerating plants, heat pipes, in the mirrors of high-capacity lasers, in the targets and resonators of charged particle accelerators and for external cooling of reactor vessels under emergency conditions.

  5. Zero Boil-Off System Design and Thermal Analysis of the Bimodal Thermal Nuclear Rocket

    Science.gov (United States)

    Christie, Robert J.; Plachta, David W.

    2006-01-01

    Mars exploration studies at NASA are evaluating vehicles that incorporate Bimodal Nuclear Thermal Rocket (BNTR) propulsion which use a high temperature nuclear fission reactor and hydrogen to produce thermal propulsion. The hydrogen propellant is to be stored in liquid state for periods up to 18 months. To prevent boil-off of the liquid hydrogen, a system of passive and active components are needed to prevent heat from entering the tanks and to remove any heat that does. This report describes the design of the system components used for the BNTR Crew Transfer Vehicle and the thermal analysis performed. The results show that Zero Boil-Off (ZBO) can be achieved with the electrical power allocated for the ZBO system.

  6. Bubble dynamics and heat transfer for pool boiling on hydrophilic, superhydrophobic and biphilic surfaces

    Science.gov (United States)

    Teodori, E.; Palma, T.; Valente, T.; Moita, A. S.; Moreira, A. L. N.

    2016-09-01

    This paper proposes a detailed analysis of bubble dynamics to describe pool boiling heat transfer in extreme wetting scenarios (superhydrophobic vs hydrophilic). A mechanistic approach, based on extensive post-processing allows quantifying the relative advantage of the superhydrophobic surfaces to endorse the onset of boiling at very low superheats (1-2K) vs their worse heat transfer performance associated to the swift formation of an insulating vapour film. Based on this analysis, a simple biphilic surface is created. The results suggest that for high heat fluxes, bubble dynamics is dominated by the emission of very small bubbles, which seems to affect the interaction mechanisms, precluding the emission of the large bubbles from the surface, thus compromising the good performance of the biphilic surfaces.

  7. Explosive boiling of a metallic glass superheated by nanosecond pulse laser ablation

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, M. Q., E-mail: mqjiang@imech.ac.cn, E-mail: lhdai@lnm.imech.ac.cn [State Key Laboratory of Nonlinear Mechanics, Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190 (China); Institute of Materials Physics, Westfälische Wilhelms-Universität Münster, Münster 48149 (Germany); Wei, Y. P. [Key Laboratory of Mechanics in Fluid Solid Coupling Systems, Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190 (China); Wilde, G. [Institute of Materials Physics, Westfälische Wilhelms-Universität Münster, Münster 48149 (Germany); Dai, L. H., E-mail: mqjiang@imech.ac.cn, E-mail: lhdai@lnm.imech.ac.cn [State Key Laboratory of Nonlinear Mechanics, Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190 (China)

    2015-01-12

    We report an explosive boiling in a Zr-based (Vitreloy 1) bulk metallic glass irradiated by a nanosecond pulse laser with a single shot. This critical phenomenon is accompanied by the ejection of high-temperature matter from the target and the formation of a liquid-gas spinodal pattern on the irradiated area. An analytical model reveals that the glassy target experiences the normal heating (melting) and significant superheating, eventually culminating in explosive boiling near the spinodal limit. Furthermore, the time lag of nucleation and the critical radius of vapor bubbles are theoretically predicted, which are in agreement with the experimental observations. This study provides the investigation on the instability of a metallic glass liquid near the thermodynamic critical temperature.

  8. Performance evaluation of the cavities on nucleate boiling at microscale level

    CERN Document Server

    Mu, Yu-Tong; Kang, Qinjun; Tao, Wen-Quan

    2015-01-01

    Nucleate boiling heat transfer (NBHT) from enhanced structures is an effective way to dissipate high heat flux. In the present study, the cavities behaviours for nucleation on roughened surface are numerically studied on the entire ebullition cycle based on a phase-change lattice Boltzmann method without introducing any artificial disturbances. The adopted model is firstly validated with the Laplace law and the two phase coexistence curve, and then applied to investigate the effects of cavity structure on NBHT. The bubble departure diameter, departure frequency and total boiling heat flux of an ebullition cycle are also explored. It is demonstrated that the cavity widths and the cavity grooves show significant influence on the features of NBHT. Cavity with circular groove in the present research shows the best performance for NBHT in terms of the averaged heat flux and bubble release frequency. When a specific cavity is combined with other different cavities on roughened surfaces its nucleation process on dif...

  9. High methane storage capacity in aluminum metal-organic frameworks.

    Science.gov (United States)

    Gándara, Felipe; Furukawa, Hiroyasu; Lee, Seungkyu; Yaghi, Omar M

    2014-04-09

    The use of porous materials to store natural gas in vehicles requires large amounts of methane per unit of volume. Here we report the synthesis, crystal structure and methane adsorption properties of two new aluminum metal-organic frameworks, MOF-519 and MOF-520. Both materials exhibit permanent porosity and high methane volumetric storage capacity: MOF-519 has a volumetric capacity of 200 and 279 cm(3) cm(-3) at 298 K and 35 and 80 bar, respectively, and MOF-520 has a volumetric capacity of 162 and 231 cm(3) cm(-3) under the same conditions. Furthermore, MOF-519 exhibits an exceptional working capacity, being able to deliver a large amount of methane at pressures between 5 and 35 bar, 151 cm(3) cm(-3), and between 5 and 80 bar, 230 cm(3) cm(-3).

  10. High Methane Storage Capacity in Aluminum Metal–Organic Frameworks

    Science.gov (United States)

    2015-01-01

    The use of porous materials to store natural gas in vehicles requires large amounts of methane per unit of volume. Here we report the synthesis, crystal structure and methane adsorption properties of two new aluminum metal–organic frameworks, MOF-519 and MOF-520. Both materials exhibit permanent porosity and high methane volumetric storage capacity: MOF-519 has a volumetric capacity of 200 and 279 cm3 cm–3 at 298 K and 35 and 80 bar, respectively, and MOF-520 has a volumetric capacity of 162 and 231 cm3 cm–3 under the same conditions. Furthermore, MOF-519 exhibits an exceptional working capacity, being able to deliver a large amount of methane at pressures between 5 and 35 bar, 151 cm3 cm–3, and between 5 and 80 bar, 230 cm3 cm–3. PMID:24661065

  11. Aging of organic materials around high-energy particle accelerators

    Science.gov (United States)

    Tavlet, Marc

    1997-08-01

    Around particle accelerators used for fundamental research on the basic structure of matter, materials and components are exposed to ionizing radiation caused by beam losses in the proton machines and by synchrotron radiation in the lepton machines. Furthermore, with the high-energy and high-intensity collisions produced from future colliders, radiation damage is also to be expected in particle-physics detectors. Therefore, for a safe and reliable operation, the radiation aging of most of the components has to be assessed prior to their selection. An extensive radiation-damage test program has been carried out at CERN for decades on a routine basis and many results have been published. The tests have mainly concentrated on magnet-coil insulations and cable-insulating materials; they are carried out in accordance with the IEC 544 standard which defines the mechanical tests to be performed and the methods of degradation evaluation. The mechanical tests are also used to assess the degradation of composite structural materials. Moreover, electrical properties of high-voltage insulations and optical properties of organic scintillators and wave guides have also been studied. Our long-term experience has pointed out many parameters to be taken into account for the estimate of the lifetime of components in the radiation environment of our accelerators. One of the main parameters is the dose-rate effect, but the influence of other parameters has sometimes to be taken into account.

  12. Organic/Inorganic Nano-hybrids with High Dielectric Constant for Organic Thin Film Transistor Applications

    Science.gov (United States)

    Yu, Yang-Yen; Jiang, Ai-Hua; Lee, Wen-Ya

    2016-11-01

    The organic material soluble polyimide (PI) and organic-inorganic hybrid PI-barium titanate (BaTiO3) nanoparticle dielectric materials (IBX, where X is the concentration of BaTiO3 nanoparticles in a PI matrix) were successfully synthesized through a sol-gel process. The effects of various BaTiO3 contents on the hybrid film performance and performance optimization were investigated. Furthermore, pentacene-based organic thin film transistors (OTFTs) with PI-BaTiO3/polymethylmethacrylate or cyclic olefin copolymer (COC)-modified gate dielectrics were fabricated and examined. The hybrid materials showed effective dispersion of BaTiO3 nanoparticles in the PI matrix and favorable thermal properties. X-ray diffraction patterns revealed that the BaTiO3 nanoparticles had a perovskite structure. The hybrid films exhibited high formability and planarity. The IBX hybrid dielectric films exhibited tunable insulating properties such as the dielectric constant value and capacitance in ranges of 4.0-8.6 and 9.2-17.5 nF cm-2, respectively. Adding the modified layer caused the decrease of dielectric constant values and capacitances. The modified dielectric layer without cross-linking displayed a hydrophobic surface. The electrical characteristics of the pentacene-based OTFTs were enhanced after the surface modification. The optimal condition for the dielectric layer was 10 wt% hybrid film with the COC-modified layer; moreover, the device exhibited a threshold voltage of 0.12 V, field-effect mobility of 4.32 × 10-1 cm2 V-1 s-1, and on/off current of 8.4 × 107.

  13. Studies on sodium boiling phenomena in out of pile rod bundles for various accidental situations in Liquid Metal Fast Breeder Reactors (LMFBR) experiments and interpretations

    Science.gov (United States)

    Seiler, J. M.; Rameau, B.

    Bundle sodium boiling in nominal geometry for different accident conditions is reviewed. Voiding of a subassembly is controlled by not only hydrodynamic effects but mainly by thermal effects. There is a strong influence of the thermal inertia of the bundle material compared to the sodium thermal inertia. Flow instability, during a slow transient, can be analyzed with numerical tools and estimated using simplified approximations. Stable boiling operational conditions under bundle mixed convection (natural convection in the reactor) can be predicted. Voiding during a fast transient can be approximated from single channel calculations. The phenomenology of boiling behavior for a subassembly with inlet completely blocked, submitted to decay heat and lateral cooling; two-phase sodium flow pressure drop in a tube of large hydraulic diameter under adiabatic conditions; critical flow phenomena and voiding rate under high power, slow transient conditions; and onset of dry out under local boiling remains problematical.

  14. Nano-inspired fluidic interactivity for boiling heat transfer: impact and criteria

    Science.gov (United States)

    Kim, Beom Seok; Choi, Geehong; Shin, Sangwoo; Gemming, Thomas; Cho, Hyung Hee

    2016-01-01

    The enhancement of boiling heat transfer, the most powerful energy-transferring technology, will lead to milestones in the development of high-efficiency, next-generation energy systems. Perceiving nano-inspired interface functionalities from their rough morphologies, we demonstrate interface-induced liquid refreshing is essential to improve heat transfer by intrinsically avoiding Leidenfrost phenomenon. High liquid accessibility of hemi-wicking and catalytic nucleation, triggered by the morphological and hydrodynamic peculiarities of nano-inspired interfaces, contribute to the critical heat flux (CHF) and the heat transfer coefficient (HTC). Our experiments show CHF is a function of universal hydrodynamic characteristics involving interfacial liquid accessibility and HTC is improved with a higher probability of smaller nuclei with less superheat. Considering the interface-induced and bulk liquid accessibility at boiling, we discuss functionalizing the interactivity between an interface and a counteracting fluid seeking to create a novel interface, a so-called smart interface, for a breakthrough in boiling and its pragmatic application in energy systems. PMID:27708341

  15. Tissue Erosion Using Shock Wave Heating and Millisecond Boiling in HIFU Fields

    Science.gov (United States)

    Canney, Michael S.; Khokhlova, Tatiana D.; Khokhlova, Vera A.; Bailey, Michael R.; Ha Hwang, Joo; Crum, Lawrence A.

    2010-03-01

    A wide variety of treatment protocols have been employed in high intensity focused ultrasound (HIFU) treatments, and the resulting bioeffects observed include both mechanical as well as thermal effects. In recent studies, there has been significant interest in generating purely mechanical damage using protocols with short, microsecond pulses. Tissue erosion effects have been attained by operating HIFU sources using short pulses of 10-20 cycles, low duty cycles (<1%), and pulse average intensities of greater than 20 kW/cm2. The goal of this work was to use a modified pulsing protocol, consisting of longer, millisecond-long pulses of ultrasound and to demonstrate that heating and rapid millisecond boiling from shock wave formation can be harnessed to induce controlled mechanical destruction of soft tissue. Experiments were performed in excised bovine liver and heart tissue using a 2-MHz transducer. Boiling activity was monitored during exposures using a high voltage probe in parallel with the HIFU source. In situ acoustic fields and heating rates were determined for exposures using a novel derating approach for nonlinear HIFU fields. Several different exposure protocols were used and included varying the duty cycle, pulse length, and power to the source. After exposures, the tissue was sectioned, and the gross lesion morphology was observed. Different types of lesions were induced in experiments that ranged from purely thermal to purely mechanical depending on the pulsing protocol used. Therefore, shock wave heating and millisecond boiling may be an effective method for reliably generating significant tissue erosion effects.

  16. Nano-inspired fluidic interactivity for boiling heat transfer: impact and criteria.

    Science.gov (United States)

    Kim, Beom Seok; Choi, Geehong; Shin, Sangwoo; Gemming, Thomas; Cho, Hyung Hee

    2016-10-06

    The enhancement of boiling heat transfer, the most powerful energy-transferring technology, will lead to milestones in the development of high-efficiency, next-generation energy systems. Perceiving nano-inspired interface functionalities from their rough morphologies, we demonstrate interface-induced liquid refreshing is essential to improve heat transfer by intrinsically avoiding Leidenfrost phenomenon. High liquid accessibility of hemi-wicking and catalytic nucleation, triggered by the morphological and hydrodynamic peculiarities of nano-inspired interfaces, contribute to the critical heat flux (CHF) and the heat transfer coefficient (HTC). Our experiments show CHF is a function of universal hydrodynamic characteristics involving interfacial liquid accessibility and HTC is improved with a higher probability of smaller nuclei with less superheat. Considering the interface-induced and bulk liquid accessibility at boiling, we discuss functionalizing the interactivity between an interface and a counteracting fluid seeking to create a novel interface, a so-called smart interface, for a breakthrough in boiling and its pragmatic application in energy systems.

  17. Enhancement of Pool Boiling Heat Transfer to Lithium Bromide Aqueous Solution

    Science.gov (United States)

    Furukawa, Masahiro; Kaji, Masuo; Suyama, Takayuki; Sekoguchi, Kotohiko

    An experimental study on enhancement of nucleate pool boiling heat tranfer by placing a sponge metal close to a plain heated surface was conducted in order to improve the heat transfer performance of the high temperature generator of absorption chiller/heater. The sponge metal has three dimensional porous mesh framework like sponge. Boiling curves of water under the atmospheric pressure were compared with those of lithium bromide aqueous solution of mass concentration 55 to 58%. Heat transfer characteristics were improved by 2 to3 times both for water and lithium bromide aqueous solution when the sponge metal was placed on the heated surface with and without cleareance. Three kinds of sponge metals were used for lithium bromide aqueous solution under the reduced pressure (24 kPa). At lower heat fluxes,#6 sponge metal which has the finest mesh and the lowest porosity shows excellent results. At high heat fluxes, however,it causes deterioration of heat transfer. Over the wide range of heat fluxes,# 4 sponge metal was found to be most suitable and the optimal clearence was determined as 0.5 mm. The sponge metal is of good practical use as a device to enhance the boiling, since no special manufacturing is required for placing it on the heated surface.

  18. Nano-inspired fluidic interactivity for boiling heat transfer: impact and criteria

    Science.gov (United States)

    Kim, Beom Seok; Choi, Geehong; Shin, Sangwoo; Gemming, Thomas; Cho, Hyung Hee

    2016-10-01

    The enhancement of boiling heat transfer, the most powerful energy-transferring technology, will lead to milestones in the development of high-efficiency, next-generation energy systems. Perceiving nano-inspired interface functionalities from their rough morphologies, we demonstrate interface-induced liquid refreshing is essential to improve heat transfer by intrinsically avoiding Leidenfrost phenomenon. High liquid accessibility of hemi-wicking and catalytic nucleation, triggered by the morphological and hydrodynamic peculiarities of nano-inspired interfaces, contribute to the critical heat flux (CHF) and the heat transfer coefficient (HTC). Our experiments show CHF is a function of universal hydrodynamic characteristics involving interfacial liquid accessibility and HTC is improved with a higher probability of smaller nuclei with less superheat. Considering the interface-induced and bulk liquid accessibility at boiling, we discuss functionalizing the interactivity between an interface and a counteracting fluid seeking to create a novel interface, a so-called smart interface, for a breakthrough in boiling and its pragmatic application in energy systems.

  19. Micro-bubble emission boiling with the cavitation bubble blow pit

    Science.gov (United States)

    Inada, Shigeaki; Shinagawa, Kazuaki; Illias, Suhaimi Bin; Sumiya, Hiroyuki; Jalaludin, Helmisyah A.

    2016-09-01

    The miniaturization boiling (micro-bubble emission boiling [MEB]) phenomenon, with a high heat removal capacity that contributes considerably to the cooling of the divertor of the nuclear fusion reactor, was discovered in the early 1980s. Extensive research on MEB has been performed since its discovery. However, the progress of the application has been delayed because the generation mechanism of MEB remains unclear. Reasons for this lack of clarity include the complexity of the phenomenon itself and the high-speed phase change phenomenon in which boiling and condensation are rapidly generated. In addition, a more advanced thermal technique is required to realize the MEB phenomenon at the laboratory scale. To the authors’ knowledge, few studies have discussed the rush mechanism of subcooled liquid to the heating surface, which is critical to elucidating the mechanism behind MEB. This study used photographic images to verify that the cavitation phenomenon spreads to the inside of the superheated liquid on the heating surface and thus clarify the mechanism of MEB.

  20. Micro-bubble emission boiling with the cavitation bubble blow pit

    Science.gov (United States)

    Inada, Shigeaki; Shinagawa, Kazuaki; Illias, Suhaimi Bin; Sumiya, Hiroyuki; Jalaludin, Helmisyah A.

    2016-01-01

    The miniaturization boiling (micro-bubble emission boiling [MEB]) phenomenon, with a high heat removal capacity that contributes considerably to the cooling of the divertor of the nuclear fusion reactor, was discovered in the early 1980s. Extensive research on MEB has been performed since its discovery. However, the progress of the application has been delayed because the generation mechanism of MEB remains unclear. Reasons for this lack of clarity include the complexity of the phenomenon itself and the high-speed phase change phenomenon in which boiling and condensation are rapidly generated. In addition, a more advanced thermal technique is required to realize the MEB phenomenon at the laboratory scale. To the authors’ knowledge, few studies have discussed the rush mechanism of subcooled liquid to the heating surface, which is critical to elucidating the mechanism behind MEB. This study used photographic images to verify that the cavitation phenomenon spreads to the inside of the superheated liquid on the heating surface and thus clarify the mechanism of MEB. PMID:27628271

  1. Inspection of Pool Boiling with Superhydrophilic and Superhydrophobic Coating

    Energy Technology Data Exchange (ETDEWEB)

    Son, Gyumin; Moon, Sung Bo; Bang, In Cheol [UNIST, Ulsan (Korea, Republic of)

    2015-05-15

    In conventional nuclear power plants, increasing critical heat flux (CHF) margin by converting existing parts is economically meaningful since it means overall energy production increase without building additional power plants. There were researches to enhance margin from the very beginning of the commercialization of nuclear power plants and many efforts have led to current model of plants, optimized for both safety and production efficiency. Examples are mixing vane which is actually applied to plants nowadays, using nanofluids to enhance heat transfer coefficient (HTC), trying porous surfaces and so on. Takata et al. studied effects of surface wettability by using hydrophobic coating and observed enhanced nucleate boiling at coated surface regions. Betz et al. experimented superhydrophilic (SHPi), superhydrophobic (SHPo), and superbiphilic surfaces. Results indicate heat transfer coefficient enhancement due to increase of nucleation sites by hydrophobic regions and constrained diameter of growing bubbles by hydrophilic regions. Although it would be rough to apply their concept to real reactor coolant surface wall, understanding the possibility of enhanced boiling is meaningful. In this paper, SHPi and SHPo coatings were applied to wire at traditional pool boiling experiment by Nukiyama. By observing altered CHF margin and nucleate boiling, the effects of each coating and their tendencies are discussed. SHPi, SHPo and bare wire's pool boiling was investigated and their boiling graphs were discussed. SHPi shows enhancement in CHF while SHPo's case is more complicated since there were variables like partial CHF or micro scale bubbles. Additional experiment could be comparing HTC, checking whether hydrophobic wire's nucleate boiling enhancement can exceed the decreased CHF margin. More sophisticated method to remove unwanted bubbles should be considered such as using degassed water.

  2. High-Efficiency Organic Solar Concentrators for Photovoltaics

    National Research Council Canada - National Science Library

    Michael J. Currie; Jonathan K. Mapel; Timothy D. Heidel; Shalom Goffri; Marc A. Baldo

    2008-01-01

    The cost of photovoltaic power can be reduced with organic solar concentrators. These are planar waveguides with a thin-film organic coating on the face and inorganic solar cells attached to the edges...

  3. Highly Bright White Organic Light-Emitting Diode

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    @@ A highly bright white organic light-emitting diode (OLED) was realized by using a highly bright blue emitting layer, 1,7-diphenyl-4-biphenyl-3,5-dimethyl-l,7-dihydrodipyrazolo[3,4-b;4',3'-e]pyridine (PAP-Ph), together with a 4-(dicyanomethylene)-2-methyl-6-(4-dimethylaminostyryl)-4H-pyran (DCM)-doped Alq [tris(8-hydroxyquinolinato) aluminum (Ⅲ)] layer to provide the blue, red and green emission for color mixing. With appropriate thickness control, the white-light OLED has a performance that reaches 24700 cd/m2 at 15 V, 1.93 lm/W at 6.5 V, and >300 cd/m2 at 7.7 mA/em2. The Commission Internationale de l'Eclairage (CIE) coordinates of the emitted light vary in a very small range, from (0.35, 0.34) to (0.34, 0.35), when forward voltages change from 6 to 12 V.

  4. Highly Bright White Organic Light-Emitting Diode

    Institute of Scientific and Technical Information of China (English)

    KO; C.; W.

    2001-01-01

    A highly bright white organic light-emitting diode (OLED) was realized by using a highly bright blue emitting layer, 1,7-diphenyl-4-biphenyl-3,5-dimethyl-l,7-dihydrodipyrazolo[3,4-b;4',3'-e]pyridine (PAP-Ph), together with a 4-(dicyanomethylene)-2-methyl-6-(4-dimethylaminostyryl)-4H-pyran (DCM)-doped Alq [tris(8-hydroxyquinolinato) aluminum (Ⅲ)] layer to provide the blue, red and green emission for color mixing. With appropriate thickness control, the white-light OLED has a performance that reaches 24700 cd/m2 at 15 V, 1.93 lm/W at 6.5 V, and >300 cd/m2 at 7.7 mA/em2. The Commission Internationale de l'Eclairage (CIE) coordinates of the emitted light vary in a very small range, from (0.35, 0.34) to (0.34, 0.35), when forward voltages change from 6 to 12 V.  ……

  5. Small molecule semiconductors for high-efficiency organic photovoltaics.

    Science.gov (United States)

    Lin, Yuze; Li, Yongfang; Zhan, Xiaowei

    2012-06-01

    Organic photovoltaic cells (OPVs) are a promising cost-effective alternative to silicon-based solar cells, and possess light-weight, low-cost, and flexibility advantages. Significant progress has been achieved in the development of novel photovoltaic materials and device structures in the last decade. Nowadays small molecular semiconductors for OPVs have attracted considerable attention, due to their advantages over their polymer counterparts, including well-defined molecular structure, definite molecular weight, and high purity without batch to batch variations. The highest power conversion efficiencies of OPVs based on small molecular donor/fullerene acceptors or polymeric donor/fullerene acceptors are up to 6.7% and 8.3%, respectively, and meanwhile nonfullerene acceptors have also exhibited some promising results. In this review we summarize the developments in small molecular donors, acceptors (fullerene derivatives and nonfullerene molecules), and donor-acceptor dyad systems for high-performance multilayer, bulk heterojunction, and single-component OPVs. We focus on correlations of molecular chemical structures with properties, such as absorption, energy levels, charge mobilities, and photovoltaic performances. This structure-property relationship analysis may guide rational structural design and evaluation of photovoltaic materials (253 references).

  6. Highly Charged Protein Ions: The Strongest Organic Acids to Date.

    Science.gov (United States)

    Zenaidee, Muhammad A; Leeming, Michael G; Zhang, Fangtong; Funston, Toby T; Donald, William A

    2017-07-10

    The basicity of highly protonated cytochrome c (cyt c) and myoglobin (myo) ions were investigated using tandem mass spectrometry, ion-molecule reactions (IMRs), and theoretical calculations as a function of charge state. Surprisingly, highly charged protein ions (HCPI) can readily protonate non-polar molecules and inert gases, including Ar, O2 , and N2 in thermal IMRs. The most HCPIs that can be observed are over 130 kJ mol(-1) less basic than the least basic neutral organic molecules known (tetrafluoromethane and methane). Based on theoretical calculations, it is predicted that protonated cyt c and myo ions should spontaneously lose a proton to vacuum for charge states in which every third residue is protonated. In this study, HCPIs are formed where every fourth residue on average is protonated. These results indicate that protein ions in higher charge states can be formed using a low-pressure ion source to reduce proton-transfer reactions between protein ions and gases from the atmosphere. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. Controlling excitons. Concepts for phosphorescent organic LEDs at high brightness

    Energy Technology Data Exchange (ETDEWEB)

    Reineke, Sebastian

    2009-11-15

    This work focusses on the high brightness performance of phosphorescent organic light-emitting diodes (OLEDs). The use of phosphorescent emitter molecules in OLEDs is essential to realize internal electron-photon conversion efficiencies of 100 %. However, due to their molecular nature, the excited triplet states have orders of magnitude longer time constants compared to their fluorescent counterparts which, in turn, strongly increases the probability of bimolecular annihilation. As a consequence, the efficiencies of phosphorescent OLEDs decline at high brightness - an effect known as efficiency roll-off, for which it has been shown to be dominated by triplet-triplet annihilation (TTA). In this work, TTA of the archetype phosphorescent emitter Ir(ppy){sub 3} is investigated in time-resolved photoluminescence experiments. For the widely used mixed system CBP:Ir(ppy){sub 3}, host-guest TTA - an additional unwanted TTA channel - is experimentally observed at high excitation levels. By using matrix materials with higher triplet energies, this effect is efficiently suppressed, however further studies show that the efficiency roll-off of Ir(ppy)3 is much more pronounced than predicted by a model based on Foerster-type energy transfer, which marks the intrinsic limit for TTA. These results suggest that the emitter molecules show a strong tendency to form aggregates in the mixed film as the origin for enhanced TTA. Transmission electron microscopy images of Ir(ppy){sub 3} doped mixed films give direct proof of emitter aggregates. Based on these results, two concepts are developed that improve the high brightness performance of OLEDs. In a first approach, thin intrinsic matrix interlayers are incorporated in the emission layer leading to a one-dimensional exciton confinement that suppresses exciton migration and, consequently, TTA. The second concept reduces the efficiency roll-off by using an emitter molecule with slightly different chemical structure, i.e. Ir(ppy){sub 2

  8. Boiling-Water Reactor internals aging degradation study. Phase 1

    Energy Technology Data Exchange (ETDEWEB)

    Luk, K.H. [Oak Ridge National Lab., TN (United States)

    1993-09-01

    This report documents the results of an aging assessment study for boiling water reactor (BWR) internals. Major stressors for BWR internals are related to unsteady hydrodynamic forces generated by the primary coolant flow in the reactor vessel. Welding and cold-working, dissolved oxygen and impurities in the coolant, applied loads and exposures to fast neutron fluxes are other important stressors. Based on results of a component failure information survey, stress corrosion cracking (SCC) and fatigue are identified as the two major aging-related degradation mechanisms for BWR internals. Significant reported failures include SCC in jet-pump holddown beams, in-core neutron flux monitor dry tubes and core spray spargers. Fatigue failures were detected in feedwater spargers. The implementation of a plant Hydrogen Water Chemistry (HWC) program is considered as a promising method for controlling SCC problems in BWR. More operating data are needed to evaluate its effectiveness for internal components. Long-term fast neutron irradiation effects and high-cycle fatigue in a corrosive environment are uncertainty factors in the aging assessment process. BWR internals are examined by visual inspections and the method is access limited. The presence of a large water gap and an absence of ex-core neutron flux monitors may handicap the use of advanced inspection methods, such as neutron noise vibration measurements, for BWR.

  9. Transport Phenomena in Thin Rotating Liquid Films Including: Nucleate Boiling

    Science.gov (United States)

    Faghri, Amir

    2005-01-01

    In this grant, experimental, numerical and analytical studies of heat transfer in a thin liquid film flowing over a rotating disk have been conducted. Heat transfer coefficients were measured experimentally in a rotating disk heat transfer apparatus where the disk was heated from below with electrical resistance heaters. The heat transfer measurements were supplemented by experimental characterization of the liquid film thickness using a novel laser based technique. The heat transfer measurements show that the disk rotation plays an important role on enhancement of heat transfer primarily through the thinning of the liquid film. Experiments covered both momentum and rotation dominated regimes of the flow and heat transfer in this apparatus. Heat transfer measurements have been extended to include evaporation and nucleate boiling and these experiments are continuing in our laboratory. Empirical correlations have also been developed to provide useful information for design of compact high efficiency heat transfer devices. The experimental work has been supplemented by numerical and analytical analyses of the same problem. Both numerical and analytical results have been found to agree reasonably well with the experimental results on liquid film thickness and heat transfer Coefficients/Nusselt numbers. The numerical simulations include the free surface liquid film flow and heat transfer under disk rotation including the conjugate effects. The analytical analysis utilizes an integral boundary layer approach from which

  10. Boiling heat transfer in a small horizontal rectangular channel

    Energy Technology Data Exchange (ETDEWEB)

    Tran, T.N.; Wambsganss, M.W.; Jendrzejczyk, J.A. [Argonne National Lab., IL (United States); France, D.M. [Illinois Univ., Chicago, IL (United States). Dept. of Mechanical Engineering

    1993-08-01

    Compact heat exchangers have traditionally found wide application in the transportation industry, where they are used as evaporators and condensers in vapor compression cycles for air conditioning and refrigeration. Such heat exchangers possess numerous attractive features including high thermal effectiveness, small size, low weight, design flexibility, and pure counterflow, and they can accommodate multiple streams. Today, there is a widespread interest in expanding the range of application of compact heat exchangers to include phase-change heat transfer in the process industries, among others. An overall objective of this effort is to provide the basis for establishing design technology in this area. In the present study, small channel flow boiling heat transfer was extended to a rectangular channel (4.06 {times} 1.70 mm) using refrigerant 12 (R-12). As with the circular tube studies, the flow channel wall was electrically heated providing a constant heat flux. Tests were performed over a quality range of 0.15 to 0.80, and large ranges of mass fluxes (50 to 400 kg/m{sup 2}s) and heat flux (4 to 34 kW/m{sup 2}). Heat transfer was measured and results are compared with correlation predictions.

  11. Specifics of boiling and condensation in upward flow in minichannel systems

    Science.gov (United States)

    Kuznetsov, V. V.; Safonov, S. A.; Shamirzaev, A. S.

    2015-12-01

    The results of experimental and numerical studies focused on determining the mechanism of heat transfer during boiling and condensation in a single-row system of minichannels in upward flow conditions at a mass flux of 30 and 50 kg/(m2 s) are presented. Refrigerant R21, which models cryogenic liquids at low temperatures, was used as the working liquid. The determining influence of self-organization of the flow under the influence of capillary forces on the processes of heat transfer during a phase transition in the system of minichannels at low mass and heat fluxes was revealed.

  12. Gravity and Heater Size Effects on Pool Boiling Heat Transfer

    Science.gov (United States)

    Kim, Jungho; Raj, Rishi

    2014-01-01

    The current work is based on observations of boiling heat transfer over a continuous range of gravity levels between 0g to 1.8g and varying heater sizes with a fluorinert as the test liquid (FC-72/n-perfluorohexane). Variable gravity pool boiling heat transfer measurements over a wide range of gravity levels were made during parabolic flight campaigns as well as onboard the International Space Station. For large heaters and-or higher gravity conditions, buoyancy dominated boiling and heat transfer results were heater size independent. The power law coefficient for gravity in the heat transfer equation was found to be a function of wall temperature under these conditions. Under low gravity conditions and-or for smaller heaters, surface tension forces dominated and heat transfer results were heater size dependent. A pool boiling regime map differentiating buoyancy and surface tension dominated regimes was developed along with a unified framework that allowed for scaling of pool boiling over a wide range of gravity levels and heater sizes. The scaling laws developed in this study are expected to allow performance quantification of phase change based technologies under variable gravity environments eventually leading to their implementation in space based applications.

  13. Marangoni heat transfer in subcooled nucleate pool boiling

    Energy Technology Data Exchange (ETDEWEB)

    Petrovic, S.; Robinson, T.; Judd, R.L. [McMaster University, Hamilton, ON (Canada). Dept. of Mechanical Engineering

    2004-11-01

    The liquid motion induced by surface tension variation, termed the Marangoni effect, and its contribution to boiling heat transfer has been an issue of much controversy. Boiling heat transfer theory, although acknowledging its existence, considers its contribution to heat transfer to be insignificant in comparison with buoyancy induced convection. However, recent microgravity experiments have shown that although the boiling mechanism in a reduced gravity environment is different, the corresponding heat transfer rates are similar to those obtained under normal gravity conditions, raising questions about the validity of the assumption. An experimental investigation was performed in which distilled water was gradually heated to boiling conditions on a copper heater surface at four different levels of subcooling. Photographic investigation of the bubbles appearing on the surface was carried out in support of the measurements. The results obtained indicate that Marangoni convection associated with the bubbles formed by the air dissolved in the water which emerged from solution when the water was heated sufficiently, significantly influenced the heat transfer rate in subcooled nucleate pool boiling. A heat transfer model was developed in order to explain the phenomena observed. (author)

  14. Boiling crisis and non-equilibrium drying transition

    CERN Document Server

    Nikolayev, Vadim

    2016-01-01

    Boiling crisis is the rapid formation of the quasi-continuous vapor film between the heater and the liquid when the heat supply exceeds a critical value. We propose a mechanism for the boiling crisis that is based on the spreading of the dry spot under a vapor bubble. The spreading is initiated by the vapor recoil force, a force coming from the liquid evaporation into the bubble. Since the evaporation intensity increases sharply near the triple contact line, the influence of the vapor recoil can be described as a change of the apparent contact angle. Therefore, for the most usual case of complete wetting of the heating surface by the liquid, the boiling crisis can be understood as a drying transition from complete to partial wetting. The state of nucleate boiling, which is boiling in its usual sense, is characterized by a very large rate of heat transfer from the heating surface to the bulk because the superheated liquid is carried away from the heating surface by the departing vapor bubbles. If the heating p...

  15. Numerical investigation of nucleate pool boiling heat transfer

    Directory of Open Access Journals (Sweden)

    Stojanović Andrijana D.

    2016-01-01

    Full Text Available Multidimensional numerical simulation of the atmospheric saturated pool boiling is performed. The applied modelling and numerical methods enable a full representation of the liquid and vapour two-phase mixture behaviour on the heated surface, with included prediction of the swell level and heated wall temperature field. In this way the integral behaviour of nucleate pool boiling is simulated. The micro conditions of bubble generation at the heated wall surface are modelled by the bubble nucleation site density, the liquid wetting contact angle and the bubble grow time. The bubble nucleation sites are randomly located within zones of equal size, where the number of zones equals the nucleation site density. The conjugate heat transfer from the heated wall to the liquid is taken into account in wetted heated wall areas around bubble nucleation sites. The boiling curve relation between the heat flux and the heated wall surface temperature in excess of the saturation temperature is predicted for the pool boiling conditions reported in the literature and a good agreement is achieved with experimentally measured data. The influence of the nucleation site density on the boiling curve characteristic is confirmed. In addition, the influence of the heat flux intensity on the spatial effects of vapour generation and two-phase flow are shown, such as the increase of the swell level position and the reduced wetting of the heated wall surface by the heat flux increase. [Projekat Ministarstva nauke Republike Srbije, br. TR-33018 i br. OI-174014

  16. Experimental method for characterizing CVOC removal from fractured clays during boiling.

    Science.gov (United States)

    Liu, Xiaoling; Tan, Tianwu; Falta, Ronald W; Murdoch, Lawrence C

    2013-09-01

    Conventional remediation methods that rely on contact with contaminants can be ineffective in fractured media, but thermal methods of remediation involving CVOC stripping at boiling temperature show promise. However, limited experimental data are available to characterize thermal remediation because of challenges associated with high temperature. This research reports an experimental method using uniformly contaminated clay packed into two types of experimental cells, a rigid-wall stainless steel tube and a flexible-wall Teflon tube in a pressurized chamber. Both tubes are 5 cm in diameter and approximately 25 cm long. This laboratory apparatus was developed as a 1D physical model for contaminant transport in a cylindrical matrix towards a fracture, which is represented by one end of the cylinder and serves as the outlet of vapor and contaminant. The clay was contaminated with dissolved 1,2-dichloroethane (DCA) and bromide, and the columns were heated to more than 100 °C and then the top end was depressurized to atmospheric pressure to induce boiling. The outflow was condensed and analyzed for contaminant mass. The flexible-wall cell was confined to 100 kPa (gage), allowing equilibrium boiling temperatures of approximately 120 °C to be maintained. The clay was sampled before and after heating and extracted to determine the DCA distribution along the length of the column. During a typical test in the rigid-wall cell, internal temperatures and pressures along the column during heating reached the saturated vapor pressure curve. DCA concentrations in the recovered condensate were up to 12 times of the initial pore concentration in the clay. Less than 5% of non-volatile bromide was recovered. Significant removal of DCA and water occurred along the entire length of the clay column. This suggests that boiling was occurring in the clay matrix.

  17. Physicochemical and sensory evaluation of some cooking banana (Musa spp.) for boiling and frying process.

    Science.gov (United States)

    Belayneh, M; Workneh, T S; Belew, D

    2014-12-01

    Experiments were conducted to study physicochemical properties of four cooking banana varieties (Cardaba, Nijiru, Matoke and Kitawira) and to determine their suitability for chips processing and boiling quality. A randomized complete block design with three replications was employed. Pulp to peel ratio, pulp firmness (before and after), total soluble solids, pH, titratable acidity, ascorbic acid, ease of peeling, pulp water absorption, duration of cooking (or boiling) and dry matter are the most important parameters to evaluate the quality of cooking banana including plantain. The different variety affected the fruit physical characteristics significantly (P ≤ 0.05). The Cardaba varieties fruit was found to be the heaviest and the longest. The Kitawira and Nijiru varieties had the smallest, shortest and thinnest fruit. The Cardaba contained 88 % more edible portions per unit fresh weight than the peel. The Nijiru, Matoke and Kitawira contained more pulp weight than peel weight. Most fruit chemical quality parameters were significantly (P ≤ 0.05) affected by the varieties. Similarly, the boiling and chips qualities were significantly (P ≤ 0.05) affected by varieties. Among others, the Cardaba variety was found to have high fruit weight, fruit length, fruit girth, fruit volume, total soluble solids, ascorbic acid, dry matter and low total titratable acidity. Thus, Cardaba provided the best quality boiled pulp which can serve for diversified culinary purposes. Generally, the Nijiru, Kitawira and Matoke varieties were found to be superior to produce acceptable quality chips. These varieties are recommended for chips development by food processors in Ethiopia.

  18. Induction of a chemoattractant transcriptional response by a Campylobacter jejuni boiled cell extract in colonocytes

    Directory of Open Access Journals (Sweden)

    Connerton Phillippa L

    2009-02-01

    Full Text Available Abstract Background Campylobacter jejuni, the commonest cause of bacterial diarrhoea worldwide, can also induce colonic inflammation. To understand how a previously identified heat stable component contributes to pro-inflammatory responses we used microarray and real-time quantitative PCR to investigate the transcriptional response to a boiled cell extract of Campylobacter jejuni NCTC 11168. Results RNA was extracted from the human colonocyte line HCA-7 (clone 29 after incubation for 6 hours with Campylobacter jejuni boiled cell extract and was used to probe the Affymetrix Human Genome U133A array. Genes differentially affected by Campylobacter jejuni boiled cell extract were identified using the Significance Score algorithm of the Bioconductor software suite and further analyzed using the Ingenuity Pathway Analysis program. The chemokines CCL20, CXCL3, CXCL2, Interleukin 8, CXCL1 and CXCL6 comprised 6 of the 10 most highly up-regulated genes, all with Significance Scores ≥ 10. Members of the Tumor Necrosis Factor α/Nuclear Factor-κB super-family were also significantly up-regulated and involved in the most significantly regulated signalling pathways (Death receptor, Interleukin 6, Interleukin 10, Toll like receptor, Peroxisome Proliferator Activated Receptor-γ and apoptosis. Ingenuity Pathway Analysis also identified the most affected functional gene networks such as cell movement, gene expression and cell death. In contrast, down-regulated genes were predominantly concerned with structural and metabolic functions. Conclusion A boiled cell extract of Campylobacter jejuni has components that can directly switch the phenotype of colonic epithelial cells from one of resting metabolism to a pro-inflammatory one, particularly characterized by increased expression of genes for leukocyte chemoattractant molecules.

  19. Development of Empirical Correlation to Calculate Pool Boiling Heat Transfer of Tandem Tubes

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Myeong-Gie [Andong National University, Andong (Korea, Republic of)

    2015-10-15

    The heat exchanging tubes are in vertical alignment. For the cases, the upper tube is affected by the lower tube. Since heat transfer is closely related to the conditions of tube surface, bundle geometry, and liquid, lots of studies have been carried out for the several decades to investigate the combined effects of those factors on pool boiling heat transfer. One of the most important parameters in the analysis of a tube array is the pitch ( P ) between tubes. Many researchers have been investigated its effect on heat transfer enhancement for the tube bundles and the tandem tubes. The effect of a tube array on heat transfer enhancement was also studied for application to the flooded evaporators. Cornwell and Schuller studied the sliding bubbles by high speed photography to account the enhancement of heat transfer observed at the upper tubes of a bundle. The study by Memory et al. shows the effects of the enhanced surface and oil adds to the heat transfer of tube bundles. They identified that, for the structured and porous bundles, oil addition leads to a steady decrease in performance. The flow boiling of n-pentane across a horizontal tube bundle was investigated experimentally by Roser et al. They identified that convective evaporation played a significant part of the total heat transfer. The fouling of the tube bundle under pool boiling was also studied by Malayeri et al. They identified that the mechanisms of fouling on the middle and top heater substantially differ from those at the bottom heater.

  20. Production of tyramine by Enterococcus faecalis strains in water-boiled salted duck.

    Science.gov (United States)

    Liu, Fang; Du, Lihui; Xu, Weiyan; Wang, Daoying; Zhang, Muhan; Zhu, Yongzhi; Xu, Weimin

    2013-05-01

    The potential to produce biogenic amines was investigated with 15 Lactococcus lactis and 15 Enterococcus faecalis strains isolated from water-boiled salted duck. The production of biogenic amines from the isolated strains grown in de Man Rogosa Sharpe broth containing precursor amino acids was determined by thin-layer chromatography and high-performance liquid chromatography. None of the L. lactis strains produced any biogenic amines, whereas 12 strains of E. faecalis produced tyramine and b -phenylethylamine. PCR assays were used to detect the presence of tyrosine decarboxylase genes in all of the isolated strains. Only the 12 biogenic amine-producing Enterococcus strains had a 924-bp fragment characteristic for the tyrosine decarboxylase gene. The comparison of the amplified partial tyrDC gene sequences of the 12 positive Enterococcus strains revealed 99% similarity within the same species. The tyramine production of the sterilized water-boiled salted duck inoculated with E. faecalis R612Z1 increased significantly during storage. This study reveals that the isolated E. faecalis strains can produce tyramine and β-phenylethylamine in the medium; however, they can only produce tyramine in water-boiled salted duck.

  1. Pool boiling heat transfer on vertical fins with wire mesh structures

    Directory of Open Access Journals (Sweden)

    Pastuszko Robert

    2012-04-01

    Full Text Available Experimental investigations into pool boiling heat transfer on finned arrays with internal tunnels limited by copper wire mesh were conducted. The experiments were carried out for water, ethanol and fluorinert FC-72 at atmospheric pressure. The wire net with mesh aperture of 0.3 and 0.5 mm, sintered with the vertical side of the 10 mm high rectangular fins and horizontal inter-fin surface formed a system of connected tunnels. Tunnel width was 0.6 and 1.0 mm. Substantial enhancement of heat transfer coefficient was observed for the investigated surfaces. In water, ethanol and FC-72 boiling the highest increase in the heat transfer coefficient was obtained for the surface with mesh aperture of 0.5 mm and tunnel width of 0.6 mm. The ratio of boiling heat transfer coefficients for the investigated fins with mesh covering and smooth fins (10 mm height, at the heat flux 100 kW/m2, was about 3 for water and ethanol as working fluids.

  2. Xanthophyll content of selected vegetables commonly consumed in the Philippines and the effect of boiling.

    Science.gov (United States)

    Pasaporte, Melvin S; Rabaya, Friche Jay R; Toleco, Mitchellrey M; Flores, Dulce M

    2014-09-01

    The purpose of this study was to quantify xanthophylls in selected vegetables commonly consumed in the Philippines and to investigate the effect of boiling on their availability. Thirteen vegetables were grouped into green-leafy and non-leafy. Results showed that fresh malunggay contains the highest amount of lutein (167.1±6.1 μg/g), neoxanthin (48.66±2.31 μg/g), and violaxanthin (37.86±1.76 μg/g) while mais has the highest zeaxanthin (269.1±11.8 μg/g). Statistically, there is no significant difference (p>0.1) in xanthophyll content between fresh leafy and non-leafy samples. However, 15-min boiling (100 °C) changed this, resulting in a significant difference (pBoiling increased the availability of lutein and neoxanthin, while an opposite effect was observed for zeaxanthin and violaxanthin. Results also showed that consuming 20 g of cooked malunggay (Moringa oleifera) can provide 100% the recommended level of lutein (10 mg) for eye health, while 8 g of cooked mais (Zea mays) a day can provide a high enough level (2 mg) of zeaxanthin. Copyright © 2014 Elsevier Ltd. All rights reserved.

  3. Analysis of moving surface structures at a laser-induced boiling front

    Science.gov (United States)

    Matti, R. S.; Kaplan, A. F. H.

    2014-10-01

    Recently ultra-high speed imaging enabled to observe moving wave patterns on metal melts that experience laser-induced boiling. In laser materials processing a vertical laser-induced boiling front governs processes like keyhole laser welding, laser remote fusion cutting, laser drilling or laser ablation. The observed waves originate from temperature variations that are closely related to the melt topology. For improved understanding of the essential front mechanisms and of the front topology, for the first time a deeper systematic analysis of the wave patterns was carried out. Seven geometrical shapes of bright or dark domains were distinguished and categorized, in particular bright peaks of three kinds and dark valleys, often inclined. Two categories describe special flow patterns at the top and bottom of the front. Dynamic and statistical analysis has revealed that the shapes often combine or separate from one category to another when streaming down the front. The brightness of wave peaks typically fluctuates during 20-50 μs. This variety of thermal wave observations is interpreted with respect to the accompanying surface topology of the melt and in turn for governing local mechanisms like absorption, shadowing, boiling, ablation pressure and melt acceleration. The findings can be of importance for understanding the key process mechanisms and for optimizing laser materials processing.

  4. High magnetic field studies of BEDT-TTF organic conductors

    Energy Technology Data Exchange (ETDEWEB)

    Honold, M.M

    1999-07-01

    This Thesis gives a detailed account of the high magnetic field properties of {alpha}-phase BEDT-TTF charge-transfer salts, with particular focus on the salts {alpha}-(BEDT-TTF){sub 2}KHg(SCN){sub 4} and {alpha}-(BEDT-TTF){sub 2}TlHg(SCN){sub 4}. The existence of the bulk quantum Hall effect and its eventual destruction in the high-field limit is shown by a variety of experimental means, including magnetoresistance, magnetisation and Hall potential oscillation studies; the latter are based on a new technique specifically developed for this purpose. Chapter 1 introduces the concept of organic conductors and emphasises their potential as prototype systems of reduced dimensionality; in Chapter 2, the necessary physics and experimental techniques for their investigation are outlined. Following model calculations which suggested the possibility of the quantum Hall effect in {alpha}-phase BEDT-TTF salts, measurements of the Hall resistivity were carried out on {alpha}-(BEDT-TTF){sub 2}TlHg(SCN){sub 4} (described in Chapter 3). These exhibit a series of plateaux and represent the direct observation of the quantum Hall effect in a bulk material. Chapter 4 reports the discovery of an anomalous magnetotransport mode in the interplane resistance of {alpha}-(BEDT-TTF){sub 2}KHg(SCN){sub 4} which involves the suppression and phase inversion of the Shubnikov-de Haas oscillations at low temperatures. This is interpreted as the action of a two-dimensional chiral Fermi liquid formed from the current-carrying edge states of each quantum Hall layer. Chapter 5 reports the first observation of magnetic breakdown in the high-field phase of {alpha}-(BEDT-TTF){sub 2}KHg(SCN){sub 4}, allowing an improved description of the high-field Fermi surface topology. These results are used to develop a new model for the nested low-field Fermi surface which can explain experimental evidence previously unaccounted for. Studies of the limiting behaviour of Hall potential oscillations in Chapter 6 show

  5. Development of a novel infrared-based visualization technique to detect liquid-gas phase dynamics on boiling surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hyung Dae [Kyunghee University, Yongin (Korea, Republic of)

    2011-05-15

    Complex two-phase heat transfer phenomena such as nucleate boiling, critical heat flux, quenching and condensation govern the thermal performance of Light Water Reactors (LWRs) under normal operation and during transients/accidents. These phenomena are typically characterized by the presence of a liquid vapor- solid contact line on the surface from/to which the heat is transferred. For example, in nucleate boiling, a significant fraction of the energy needed for bubble growth comes from evaporation of a liquid meniscus, or microlayer, underneath the bubble itself. As the liquid vapor- solid line at the edge of the meniscus retreats, a circular dry patch in the middle of the bubble is exposed; the speed of the triple line retreat is a measure of the ability of the surface to transfer heat to the bubble. At very high heat fluxes, near the upper limit of the nucleate boiling regime, also known as Critical Heat Flux (CHF), the situation is characterized by larger dry areas on the surface, dispersed within an interconnected network of liquid menisci. In quenching heat transfer, which refers to the rapid cooling of a very hot object by immersion in a cooler liquid, the process is initially dominated by film boiling. In film boiling a continuous vapor film completely separates the liquid phase from the solid surface: however, as the temperature gets closer to the Leidenfrost point, intermittent and short-lived liquid-solid contacts occur at discrete locations on the surface, thus creating liquid vapor- solid interfaces once again. Ultimately, if bubble nucleation ensues at such contact points, the vapor film is disrupted and the heat transfer regime transitions from film boiling to transition boiling. Finally, in dropwise condensation, the phase transition from vapor to liquid occurs via formation of discrete droplets on the surface, and the resulting liquid-vapor-solid triple line is where heat transfer is most intense. To gain insight into and enable mechanistic

  6. Numerical simulation of pool boiling of a Lennard-Jones liquid

    KAUST Repository

    Inaoka, Hajime

    2013-09-01

    We performed a numerical simulation of pool boiling by a molecular dynamics model. In the simulation, a liquid composed of Lennard-Jones particles in a uniform gravitational field is heated by a heat source at the bottom of the system. The model successfully reproduces the change in regimes of boiling from nucleate boiling to film boiling with the increase of the heat source temperature. We present the pool boiling curve by the model, whose general behavior is consistent with those observed in experiments of pool boiling. © 2013 Elsevier B.V. All rights reserved.

  7. Highly fluorescent xerogels with entrapped carbon dots for organic scintillators

    Energy Technology Data Exchange (ETDEWEB)

    Quaranta, A., E-mail: quaranta@ing.unitn.it [University of Trento, Department of Industrial Engineering, via Mesiano, 77, 38123 Trento (Italy); Laboratori Nazionali di Legnaro, INFN, Viale dell' Università, 2, 35020 Legnaro (PD) (Italy); Carturan, S. [Laboratori Nazionali di Legnaro, INFN, Viale dell' Università, 2, 35020 Legnaro (PD) (Italy); University of Padova, Department of Physics and Astronomy “Galileo Galilei”, Via Marzolo, 8, 35131 Padova (Italy); Campagnaro, A.; Dalla Palma, M. [University of Trento, Department of Industrial Engineering, via Mesiano, 77, 38123 Trento (Italy); Laboratori Nazionali di Legnaro, INFN, Viale dell' Università, 2, 35020 Legnaro (PD) (Italy); Giarola, M.; Daldosso, N. [University of Verona, Department of Informatics, Strada le Grazie,15, 37134 Verona (Italy); Maggioni, G. [Laboratori Nazionali di Legnaro, INFN, Viale dell' Università, 2, 35020 Legnaro (PD) (Italy); University of Padova, Department of Physics and Astronomy “Galileo Galilei”, Via Marzolo, 8, 35131 Padova (Italy); Mariotto, G. [University of Verona, Department of Informatics, Strada le Grazie,15, 37134 Verona (Italy)

    2014-02-28

    Organically modified silicate thin film and bulk samples were prepared using [3-(2-aminoethylamino)propyl]trimethoxysilane (AEAP-TMOS) as precursor with the addition of different amounts of AEAP-TMOS functionalized C-dots, prepared by reaction of AEAP-TMOS and citric acid at high temperature. The synthesis of surface functionalized C-dots was followed by Fourier Transform Infrared (FTIR) spectroscopy, and the C-dots optical properties were characterized by optical absorption and UV–vis fluorescence. Thin xerogel films and bulk samples were studied by FTIR, Raman and fluorescence spectroscopy. Intense blue-green emission was observed by UV excitation of functionalized C-dots. Carbon quantum dot (CQD) luminescence was preserved also in the xerogel matrices, and the energy transfer from the matrix to CQDs, which is a key characteristic for scintillation detectors, was investigated in the two systems. - Highlights: • Functionalized carbon dots were synthesized. • Carbon dots were dispersed in hybrid xerogel bulk and thin film. • Carbon dots exhibit a strong tunable blue luminescence. • Xerogels were characterized by FT-IR, Raman and fluorescence spectroscopies. • Energy transfer processes were evidenced between C-dots and xerogel matrix.

  8. High content image cytometry in the context of subnuclear organization.

    Science.gov (United States)

    De Vos, W H; Van Neste, L; Dieriks, B; Joss, G H; Van Oostveldt, P

    2010-01-01

    The organization of proteins in space and time is essential to their function. To accurately quantify subcellular protein characteristics in a population of cells with regard for the stochasticity of events in a natural context, there is a fast-growing need for image-based cytometry. Simultaneously, the massive amount of data that is generated by image-cytometric analyses, calls for tools that enable pattern recognition and automated classification. In this article, we present a general approach for multivariate phenotypic profiling of individual cell nuclei and quantification of subnuclear spots using automated fluorescence mosaic microscopy, optimized image processing tools, and supervised classification. We demonstrate the efficiency of our analysis by determination of differential DNA damage repair patterns in response to genotoxic stress and radiation, and we show the potential of data mining in pinpointing specific phenotypes after transient transfection. The presented approach allowed for systematic analysis of subnuclear features in large image data sets and accurate classification of phenotypes at the level of the single cell. Consequently, this type of nuclear fingerprinting shows potential for high-throughput applications, such as functional protein assays or drug compound screening.

  9. Inkjet printed organic electrochemical transistors with highly conducting polymer electrolytes

    Science.gov (United States)

    Afonso, Mónica; Morgado, Jorge; Alcácer, Luís

    2016-10-01

    Organic Electrochemical Transistors (OECTs) were fabricated with two kinds of highly conducting polymer electrolytes, one with cations of small dimensions (Li+) and the other with cations of large dimensions (1-ethyl-3-methylimidazolium, EMI+). All OECTs exhibit transconductance values in the millisiemens range. Those with the larger EMI+ cations reach higher transconductance values and the saturated region of their I(V) characteristics extends to drain negative voltages of the order of -2 V without breakdown. These OECTs aim at potential applications for which it is relevant to use a solid polymer electrolyte instead of an aqueous electrolyte, namely, for integration in complex devices or in sensors and transducers where the electrolyte film may act as a membrane to prevent direct contact of the active material (PEDOT:PSS) with the biological media. The choice of electrolytes with cations of disparate sizes aims at assessing the nature (Faradaic or capacitive) of the processes occurring at the electrolyte/channel interface. The results obtained are consistent with a Faradaic-based operation mechanism.

  10. High Performance Organ-Specific Nuclear Medicine Imagers.

    Science.gov (United States)

    Majewski, Stan

    2006-04-01

    One of the exciting applications of nuclear science is nuclear medicine. Well-known diagnostic imaging tools such as PET and SPECT (as well as MRI) were developed as spin-offs of basic scientific research in atomic and nuclear physics. Development of modern instrumentation for applications in particle physics experiments offers an opportunity to contribute to development of improved nuclear medicine (gamma and positron) imagers, complementing the present set of standard imaging tools (PET, SPECT, MRI, ultrasound, fMRI, MEG, etc). Several examples of new high performance imagers developed in national laboratories in collaboration with academia will be given to demonstrate this spin-off activity. These imagers are designed to specifically image organs such as breast, heart, head (brain), or prostate. The remaining and potentially most important challenging application field for dedicated nuclear medicine imagers is to assist with cancer radiation treatments. Better control of radiation dose delivery requires development of new compact in-situ imagers becoming integral parts of the radiation delivery systems using either external beams or based on radiation delivery by inserting or injecting radioactive sources (gamma, beta or alpha emitters) into tumors.

  11. Boiling heat transfer on fins – experimental and numerical procedure

    Directory of Open Access Journals (Sweden)

    Orzechowski T.

    2014-03-01

    Full Text Available The paper presents the research methodology, the test facility and the results of investigations into non-isothermal surfaces in water boiling at atmospheric pressure, together with a discussion of errors. The investigations were conducted for two aluminium samples with technically smooth surfaces and thickness of 4 mm and 10 mm, respectively. For the sample of lower thickness, on the basis of the surface temperature distribution measured with an infrared camera, the local heat flux and the heat transfer coefficient were determined and shown in the form of a boiling curve. For the thicker sample, for which 1-D model cannot be used, numerical calculations were conducted. They resulted in obtaining the values of the local heat flux on the surface the invisible to the infrared, camera i.e. on the side on which the boiling of the medium proceeds.

  12. Changes of enthalpy slope in subcooled flow boiling

    Energy Technology Data Exchange (ETDEWEB)

    Collado, Francisco J.; Monne, Carlos [Universidad de Zaragoza-CPS, Departamento de Ingenieria Mecanica-Motores Termicos, Zaragoza (Spain); Pascau, Antonio [Universidad de Zaragoza-CPS, Departamento de Ciencia de los Materiales y Fluidos-Mecanica de Fluidos, Zaragoza (Spain)

    2006-03-01

    Void fraction data in subcooled flow boiling of water at low pressure measured by General Electric in the 1960s are analyzed following the classical model of Griffith et al. (in Proceedings of ASME-AIChE heat transfer conference, 58-HT-19, 1958). In addition, a new proposal for analyzing one-dimensional steady flow boiling is used. This is based on the physical fact that if the two phases have different velocities, they cannot cover the same distance - the control volume length - in the same time. So a slight modification of the heat balance is suggested, i.e., the explicit inclusion of the vapor-liquid velocity ratio or slip ratio as scaling time factor between the phases, which is successfully checked against the data. Finally, the prediction of void fraction using correlations of the net rate of change of vapor enthalpy in the fully developed regime of subcooled flow boiling is explored. (orig.)

  13. Changes of enthalpy slope in subcooled flow boiling

    Science.gov (United States)

    Collado, Francisco J.; Monné, Carlos; Pascau, Antonio

    2006-03-01

    Void fraction data in subcooled flow boiling of water at low pressure measured by General Electric in the 1960s are analyzed following the classical model of Griffith et al. (in Proceedings of ASME-AIChE heat transfer conference, #58-HT-19, 1958). In addition, a new proposal for analyzing one-dimensional steady flow boiling is used. This is based on the physical fact that if the two phases have different velocities, they cannot cover the same distance—the control volume length—in the same time. So a slight modification of the heat balance is suggested, i.e., the explicit inclusion of the vapor liquid velocity ratio or slip ratio as scaling time factor between the phases, which is successfully checked against the data. Finally, the prediction of void fraction using correlations of the net rate of change of vapor enthalpy in the fully developed regime of subcooled flow boiling is explored.

  14. Minimizing wafer defectivity during high-temperature baking of organic films in 193nm lithography

    Science.gov (United States)

    Randall, Mai; Longstaff, Christopher; Ueda, Kenichi; Nicholson, Jim; Winter, Thomas

    2006-03-01

    Demands for continued defect reduction in 300mm IC manufacturing is driving process engineers to examine all aspects of the apply process for improvement. Process engineers, and their respective tool sets, are required to process films at temperatures above the boiling point of the casting solvents. This can potentially lead to the sublimation of the film chemical components. The current methods used to minimize wafer defectivity due to bake residues include frequent cleaning of bake plate modules and surrounding equipment, process optimization, and hardware improvements until more robust chemistries are available. IBM has evaluated the Tokyo Electron CLEAN TRACK TM ACT TM 12 high exhaust high temperature hotplate (HHP) lid to minimize wafer level contamination due to the outgasing of a bottom anti-reflective coating (BARC) films during the high temperature bake process. Goal was to minimize airborne contamination (particles in free space), reduce hotplate contamination build up, and ultimately reduce defects on the wafer. This evaluation was performed on a 193nm BARC material. Evaluation data included visual hardware inspections, airborne particle counting, relative thickness build up measurements on hotplate lids, wafer level defect measurements, and electrical open fail rate. Film coat thickness mean and uniformity were also checked to compare the high exhaust HHP with the standard HHP lid. Chemical analysis of the HHP module residue was performed to identify the source material. The work will quantify potential cost savings achieved by reducing added wafer defects during processing and extending PM frequency for equipment cleaning.

  15. Several Organic Salts with High Two-Photon Active

    Institute of Scientific and Technical Information of China (English)

    TIAN, Yu-Peng; JIANG, Min-Hua; WANG, He-Zhou; FANG, Qi

    2001-01-01

    Several organic salts with D-A molecular structure and different counterion have been prepared and experimentally investigated. The two-photon induced frequency-upconverted spectra and two-photon pumped lasing are measured for the organic salt solutions in various solvents. The results indicate that counterions have influence on their stability and lasing property.

  16. Managing high need for achievement in youth organizations

    Directory of Open Access Journals (Sweden)

    Mihaela Vlad

    2007-05-01

    Full Text Available Student organizations in Romania are beginning to take their role as "bridge builders" more and more seriously. In order to effectively link the theoretical world in the classroom to the social realities and the demand of the labour market, these student organizations need: solid values, the ability to provide challenging development opportunities for members and not least, determined and inspiring managers.

  17. An experimental investigation of liquid methane convection and boiling in rocket engine cooling channels

    Science.gov (United States)

    Trujillo, Abraham Gerardo

    In the past decades, interest in developing hydrocarbon-fueled rocket engines for deep spaceflight missions has continued to grow. In particular, liquid methane (LCH4) has been of interest due to the weight efficiency, storage, and handling advantages it offers over several currently used propellants. Deep space exploration requires reusable, long life rocket engines. Due to the high temperatures reached during combustion, the life of an engine is significantly impacted by the cooling system's efficiency. Regenerative (regen) cooling is presented as a viable alternative to common cooling methods such as film and dump cooling since it provides improved engine efficiency. Due to limited availability of experimental sub-critical liquid methane cooling data for regen engine design, there has been an interest in studying the heat transfer characteristics of the propellant. For this reason, recent experimental studies at the Center for Space Exploration Technology Research (cSETR) at the University of Texas at El Paso (UTEP) have focused on investigating the heat transfer characteristics of sub-critical CH4 flowing through sub-scale cooling channels. To conduct the experiments, the csETR developed a High Heat Flux Test Facility (HHFTF) where all the channels are heated using a conduction-based thermal concentrator. In this study, two smooth channels with cross sectional geometries of 1.8 mm x 4.1 mm and 3.2 mm x 3.2 mm were tested. In addition, three roughened channels all with a 3.2 mm x 3.2 mm square cross section were also tested. For the rectangular smooth channel, Reynolds numbers ranged between 68,000 and 131,000, while the Nusselt numbers were between 40 and 325. For the rough channels, Reynolds numbers ranged from 82,000 to 131,000, and Nusselt numbers were between 65 and 810. Sub-cooled film-boiling phenomena were confirmed for all the channels presented in this work. Film-boiling onset at Critical Heat Flux (CHF) was correlated to a Boiling Number (Bo) of

  18. On Boiling of Crude Oil under Elevated Pressure

    CERN Document Server

    Pimenova, Anastasiya V

    2015-01-01

    We construct a thermodynamic model for theoretical calculation of the boiling process of multicomponent mixtures of hydrocarbons (e.g., crude oil). The model governs kinetics of the mixture composition in the course of the distillation process along with the boiling temperature increase. The model heavily relies on the theory of dilute solutions of gases in liquids. Importantly, our results are applicable for modelling the process under elevated pressure (while the empiric models for oil cracking are not scalable to the case of extreme pressure), such as in an oil field heated by lava intrusions.

  19. Towards High Performance Organic Photovoltaic Cells: A Review of Recent Development in Organic Photovoltaics

    Directory of Open Access Journals (Sweden)

    Junsheng Yu

    2014-09-01

    Full Text Available Organic photovoltaic cells (OPVs have been a hot topic for research during the last decade due to their promising application in relieving energy pressure and environmental problems caused by the increasing combustion of fossil fuels. Much effort has been made toward understanding the photovoltaic mechanism, including evolving chemical structural motifs and designing device structures, leading to a remarkable enhancement of the power conversion efficiency of OPVs from 3% to over 15%. In this brief review, the advanced progress and the state-of-the-art performance of OPVs in very recent years are summarized. Based on several of the latest developed approaches to accurately detect the separation of electron-hole pairs in the femtosecond regime, the theoretical interpretation to exploit the comprehensive mechanistic picture of energy harvesting and charge carrier generation are discussed, especially for OPVs with bulk and multiple heterojunctions. Subsequently, the novel structural designs of the device architecture of OPVs embracing external geometry modification and intrinsic structure decoration are presented. Additionally, some approaches to further increase the efficiency of OPVs are described, including thermotics and dynamics modification methods. Finally, this review highlights the challenges and prospects with the aim of providing a better understanding towards highly efficient OPVs.

  20. Application of S{gamma} Model for the Mechanistic Bubble Size Prediction in the Subcooled Boiling Flow with CFD Code

    Energy Technology Data Exchange (ETDEWEB)

    Yun, B. J.; Song, C. H. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Splawski, A.; Lo, S. [CD-adapco, Melville (United States)

    2010-10-15

    Accurate simulation of subcooled boiling flow is essential for the operation and safety of nuclear power plants (NPP). In recent years, the use of computational fluid dynamics (CFD) codes has been extended to the analysis of multi-dimensional two-phase flow for the NPP. Among the applications of CFD code for the NPP analysis, the first target was selected as a mechanistic prediction of DNB (Departure from Nucleate Boiling) in PWR. In DNB-type CHF (Critical Heat Flux), the expected flow regime is bubbly or churn turbulent flow in the high mass flux and high heat flux condition and thus subcooled boiling is also one of the key phenomena for the precise prediction of DNB. In this paper, S{gamma},which is a mechanistic transport equation for the bubble parameters, was examined in a CFD code with the objective of enhancing the prediction capability of subcooled boiling flows. The models were applied in the STAR-CD 4.12 software

  1. The Food Web of Boiling Springs Lake Appears Dominated by the Heterolobosean Tetramitus thermacidophilus Strain BSL.

    Science.gov (United States)

    Reeder, William H H; Sanck, Jessica; Hirst, Marissa; Dawson, Scott C; Wolfe, Gordon V

    2015-01-01

    We studied the protist grazers of Boiling Springs Lake (BSL), an acid geothermal feature in Lassen Volcanic National Park, using a combination of culture and genetic approaches. The major predator in BSL is a vahlkampfiid ameba closely related (95% 18S+ITS rRNA identity) to Tetramitus thermacidophilus, a heterolobose ameboflagellate recently isolated from volcanic geothermal acidic sites in Europe and Russia, as well as an uncultured heterolobosean from the nearby Iron Mountain acid mine drainage site. Tetramitus thermacidophilus strain BSL is capable of surviving the physical extremes of BSL, with optimal growth at 38-50 °C and pH 2-5. This bacterivore also ingested conidiospores of the ascomycete Phialophora sp., but ultrastructural observations reveal the latter may not be readily digested, and conidia were not separable from the ameoboflagellate culture, suggesting a possible symbiosis. DGGE fingerprint transects studies showed the organism is restricted to near-lake environs, and we detected an average of ~500 viable cysts/cm(3) sediment on the shoreline. Other grazing protists were isolated from lakeshore environments, including the lobose amebae Acanthamoeba sp. and Hartmannella sp., and the kinetoplastid flagellate Bodo sp., but none could tolerate both low pH and high temperature. These appear to be restricted to cooler near lake geothermal features, which also contain other potential grazer morphotypes observed but not successfully cultured, including ciliates, euglenids, testate amebae, and possible cercozoans. We compare the food web of BSL with other acidic or geothermal sites, and discuss the impact of protists in this unique environment.

  2. LPWCO method for the treatment of high concentrated organic wastewater

    Institute of Scientific and Technical Information of China (English)

    1998-01-01

    Based on wet air oxidation (WAO) and Fenton reagent, thispaper raises a new low pressure wet catalytic oxidation(LPWCO)which requires low pressure for the treatment of highlyconcentrated and refractory organic wastewater. Compared withgeneral wet air oxidation, the pressure of the treatment(0.1-0.6MPa) is only one of tens to percentage of latter(3.5-10MPa). Inaddition, its temperature is no more than 180℃.Compared withFenton reagent, while H2O2/COD(weight ratio) less than 1.2, theremoval of COD in the treatment is over twenty percents more thanFenton's even the value of COD is more than 14000mg/L. In thispaper, we study the effect factor of COD removal and the mechanismof this treatment. The existence of synergistic effect (catalytic oxidation and carbonization) for COD removal in H2SO4-Fenton reagent system under the condition of applied pressure and heating (0.1-0.6MPa, 104-165℃) was verified. The best condition of this disposal are as follows:H2O2/COD(weight ratio)=0.2-1.0, Fe2+ 0.6×10-3 mol, H2SO4 0.5mol, COD>1×104mg/L, the operating pressure is 0.1-0.6MPa and temperature is 104-165℃. This method suit to dispose the high-concentrated refractory wastewater, especially to the wastewater containing H2SO produced in the manufacture of pesticide, dyestuff and petrochemical works.

  3. Length Scale and Gravity Effects on Microgravity Boiling Heat Transfer

    Science.gov (United States)

    Kim, Jungho; McQuillen, John; Balombin, Joe

    2002-01-01

    Boiling is a complex phenomenon where hydrodynamics, heat transfer, mass transfer, and interfacial phenomena are tightly interwoven. An understanding of boiling and critical heat flux in microgravity environments is of importance to space based hardware and processes such as heat exchange, cryogenic fuel storage and transportation, electronic cooling, and material processing due to the large amounts of heat that can be removed with relatively little increase in temperature. Although research in this area has been performed in the past four decades, the mechanisms by which heat is removed from surfaces in microgravity are still unclear. In earth gravity, buoyancy is an important parameter that affects boiling heat transfer through the rate at which bubbles are removed from the surface. A simple model describing the bubble departure size based on a quasistatic force balance between buoyancy and surface tension is given by the Fritz [I] relation: Bo(exp 1/2) = 0.0208 theta where Bo is the ratio between buoyancy and surface tension forces. For small, rapidly growing bubbles, inertia associated with the induced liquid motion can also cause bubble departure. In microgravity, the magnitude of effects related to natural convection and buoyancy are small and physical mechanisms normally masked by natural convection in earth gravity such as Marangoni convection can substantially influence the boiling and vapor bubble dynamics. CHF (critical heat transfer) is also substantially affected by microgravity. In 1 g environments, Bo has been used as a correlating parameter for CHF. Zuber's CHF model for an infinite horizontal surface assumes that vapor columns formed by the merger of bubbles become unstable due to a Helmholtz instability blocking the supply of liquid to the surface. The jets are spaced lambda(sub D) apart, where lambda(sub D) = 2pi square root of 3[(sigma)/(g(rho(sub l) - rho(sub v)](exp 1/2) = 2pi square root of 3 L Bo(exp -1/2) = square root of 3 lambda(sub c

  4. A one-dimensional semi-empirical model considering transition boiling effect for dispersed flow film boiling

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yu-Jou [Institute of Nuclear Engineering and Science, National Tsing Hua University, Hsinchu 30013, Taiwan, ROC (China); Pan, Chin, E-mail: cpan@ess.nthu.edu.tw [Institute of Nuclear Engineering and Science, National Tsing Hua University, Hsinchu 30013, Taiwan, ROC (China); Department of Engineering and System Science, National Tsing Hua University, Hsinchu 30013, Taiwan, ROC (China); Low Carbon Energy Research Center, National Tsing Hua University, Hsinchu 30013, Taiwan, ROC (China)

    2017-05-15

    Highlights: • Seven heat transfer mechanisms are studied numerically by the model. • A semi-empirical method is proposed to account for the transition boiling effect. • The parametric effects on the heat transfer mechanisms are investigated. • The thermal non-equilibrium phenomenon between vapor and droplets is investigated. - Abstract: The objective of this paper is to develop a one-dimensional semi-empirical model for the dispersed flow film boiling considering transition boiling effects. The proposed model consists of conservation equations, i.e., vapor mass, vapor energy, droplet mass and droplet momentum conservation, and a set of closure relations to address the interactions among wall, vapor and droplets. The results show that the transition boiling effect is of vital importance in the dispersed flow film boiling regime, since the flowing situation in the downstream would be influenced by the conditions in the upstream. In addition, the present paper, through evaluating the vapor temperature and the amount of heat transferred to droplets, investigates the thermal non-equilibrium phenomenon under different flowing conditions. Comparison of the wall temperature predictions with the 1394 experimental data in the literature, the present model ranging from system pressure of 30–140 bar, heat flux of 204–1837 kW/m{sup 2} and mass flux of 380–5180 kg/m{sup 2} s, shows very good agreement with RMS of 8.80% and standard deviation of 8.81%. Moreover, the model well depicts the thermal non-equilibrium phenomenon for the dispersed flow film boiling.

  5. 77 FR 3009 - Knowledge and Abilities Catalog for Nuclear Power Plant Operators: Advanced Boiling Water Reactors

    Science.gov (United States)

    2012-01-20

    ... From the Federal Register Online via the Government Publishing Office NUCLEAR REGULATORY COMMISSION Knowledge and Abilities Catalog for Nuclear Power Plant Operators: Advanced Boiling Water Reactors..., ``Knowledge and Abilities Catalog for Nuclear Power Plant Operators: Advanced Boiling Water Reactors.''...

  6. A Study of the Influence of Solid Particles on Boiling Hysteresis

    Institute of Scientific and Technical Information of China (English)

    M.H.Shi; J.Ma

    1992-01-01

    Experiments have been performed to determine the effects on boiling hysteresis of locally fluidized particles contained in a liquid that serves as coolant for electronic equipment.The results show that Iocally fluidized particles can diminish boiling hysteresis.

  7. 76 FR 14437 - Economic Simplified Boiling Water Reactor Standard Design: GE Hitachi Nuclear Energy; Issuance of...

    Science.gov (United States)

    2011-03-16

    ... From the Federal Register Online via the Government Publishing Office ] NUCLEAR REGULATORY COMMISSION Economic Simplified Boiling Water Reactor Standard Design: GE Hitachi Nuclear Energy; Issuance of... GE Hitachi Nuclear Energy (GEH) for the economic simplified boiling water reactor (ESBWR) standard...

  8. Microaerobic biodegradation of high organic load wastewater by ...

    African Journals Online (AJOL)

    USER

    2010-06-21

    Jun 21, 2010 ... reported the application of PSB in wastewater treatment, many researchers had ... industries since organic industrial wastewater strength is dependent on the raw .... its addition in a system is not endless, in a biological system ...

  9. A New Correlation to Predict Nucleate Pool Boiling Heat Transfer in Vertical Annuli with Closed Bottoms

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Myeong Gie [Andong National University, Andong (Korea, Republic of)

    2012-05-15

    It is important to find a way of enhancing heat transfer coefficients if the space for heat exchanger installation is limited, as it is in advanced light water reactors. One of the effective methods to increase heat transfer coefficients (h{sub b}) of pool boiling is to consider a confined space. It is well known from the literature that the confined boiling is an effective technique to enhance heat transfer. Once the flow inlet at the tube bottom is closed, a very rapid increase in heat transfer coefficient is observed at low heat fluxes (q{sup '}). The similar tendency is observed regardless of the geometric shape. Yao and Chang and Kang investigated a vertical annulus while Rops et al. investigated a confined plate. Fujita et al., in other wise, used parallel plates with side and bottom inflow is restricted. Around the upper region of the annulus with closed bottoms the downward liquid interrupts the upward movement of the bubble slugs. Thereafter, bubbles are coalescing into much bigger bubbles while fluctuating up and down in the annular space. As the heat flux increases (1) the isolate bubble region, (2) the coalesced big size bubble region, and (3) the dryout region is observed in series. The major causes of the heat transfer enhancement are related with the liquid film evaporation and active liquid agitation. Literature review on the previous studies about crevice effects on pool boiling denotes that heat transfer is highly dependent on the geometric parameters. Therefore, it is necessary to quantify the effect of each geometric parameter to estimate heat transfer coefficients accurately. Although some correlations were developed to predict pool boiling heat transfer in confined spaces based on open bottoms, the application of them to a confined space with closed bottoms could result in much error. To overcome the limits of the published correlations, Kang developed a correlation to predict pool boiling heat transfer in annuli with closed bottoms

  10. Effect of boiling regime on melt stream breakup in water

    Energy Technology Data Exchange (ETDEWEB)

    Spencer, B.W.; Gabor, J.D.; Cassulo, J.C.

    1986-01-01

    A study has been performed examining the breakup and mixing behavior of an initially coherent stream of high-density melt as it flows downward through water. This work has application to the quenching of molten core materials as they drain downward during a postulated severe reactor accident. The study has included examination of various models of breakup distances based upon interfacial instabilities dominated either by liquid-liquid contact or by liquid-vapor contact. A series of experiments was performed to provide a data base for assessment of the various modeling approaches. The experiments involved Wood's metal (T/sub m/ = 73/sup 0/C, rho = 9.2 g/cm/sup 3/, d/sub j/ = 20 mm) poured into a deep pool of water. The temperature of the water and wood's metal were varied to span the range from single-phase, liquid-liquid contact to the film boiling regime. Experiment results showed that breakup occurred largely as a result of the spreading and entrainment from the leading edge of the jet. However, for streams of sufficient lengths a breakup length could be discerned at which there was no longer a coherent central core of the jet to feed the leading edge region. The erosion of the vertical trailing column is by Kelvin-Helmoltz instabilities and related disengagement of droplets from the jet into the surrounding fluid. For conditions of liquid-liquid contact, the breakup length has been found to be about 20 jet diameters; when substantial vapor is produced at the interface due to heat transfer from the jet to the water, the breakup distance was found to range to as high as 50 jet diameters. The former values are close to the analytical prediction of Taylor, whereas the latter values are better predicted by the model of Epstein and Fauske.

  11. Impact of different wort boiling temperatures on the beer foam stabilizing properties of lipid transfer protein 1.

    Science.gov (United States)

    Van Nierop, Sandra N E; Evans, David E; Axcell, Barry C; Cantrell, Ian C; Rautenbach, Marina

    2004-05-19

    Beer consumers demand satisfactory and consistent foam stability; thus, it is a high priority for brewers. Beer foam is stabilized by the interaction between certain beer proteins, including lipid transfer protein 1 (LTP1), and isomerized hop alpha-acids, but destabilized by lipids. In this study it was shown that the wort boiling temperature during the brewing process was critical in determining the final beer LTP1 content and conformation. LTP1 levels during brewing were measured by an LTP1 ELISA, using antinative barley LTP1 polyclonal antibodies. It was observed that the higher wort boiling temperatures ( approximately 102 degrees C), resulting from low altitude at sea level, reduced the final beer LTP1 level to 2-3 microg/mL, whereas the lower wort boiling temperatures ( approximately 96 degrees C), resulting from higher altitudes (1800 m), produced LTP1 levels between 17 and 35 microg/mL. Low levels of LTP1 in combination with elevated levels of free fatty acids (FFA) resulted in poor foam stability, whereas beer produced with low levels of LTP1 and FFA had satisfactory foam stability. Previous studies indicated the need for LTP1 denaturing to improve its foam stabilizing properties. However, the results presented here show that LTP1 denaturation reduces its ability to act as a binding protein for foam-damaging FFA. These investigations suggest that wort boiling temperature is an important factor in determining the level and conformation of LTP1, thereby favoring satisfactory beer foam stability.

  12. The effect of different boiling and filtering devices on the concentration of disinfection by-products in tap water.

    Science.gov (United States)

    Carrasco-Turigas, Glòria; Villanueva, Cristina M; Goñi, Fernando; Rantakokko, Panu; Nieuwenhuijsen, Mark J

    2013-01-01

    Disinfection by-products (DBPs) are ubiquitous contaminants in tap drinking water with the potential to produce adverse health effects. Filtering and boiling tap water can lead to changes in the DBP concentrations and modify the exposure through ingestion. Changes in the concentration of 4 individual trihalomethanes (THM4) (chloroform (TCM), bromodichloromethane (BDCM), dibromochloromethane (DBCM), and bromoform (TBM)), MX, and bromate were tested when boiling and filtering high bromine-containing tap water from Barcelona. For filtering, we used a pitcher-type filter and a household reverse osmosis filter; for boiling, an electric kettle, a saucepan, and a microwave were used. Samples were taken before and after each treatment to determine the change in the DBP concentration. pH, conductivity, and free/total chlorine were also measured. A large decrease of THM4 (from 48% to 97%) and MX concentrations was observed for all experiments. Bromine-containing trihalomethanes were mostly eliminated when filtering while chloroform when boiling. There was a large decrease in the concentration of bromate with reverse osmosis, but there was a little effect in the other experiments. These findings suggest that the exposure to THM4 and MX through ingestion is reduced when using these household appliances, while the decrease of bromate is device dependent. This needs to be considered in the exposure assessment of the epidemiological studies.

  13. The Effect of Different Boiling and Filtering Devices on the Concentration of Disinfection By-Products in Tap Water

    Directory of Open Access Journals (Sweden)

    Glòria Carrasco-Turigas

    2013-01-01

    Full Text Available Disinfection by-products (DBPs are ubiquitous contaminants in tap drinking water with the potential to produce adverse health effects. Filtering and boiling tap water can lead to changes in the DBP concentrations and modify the exposure through ingestion. Changes in the concentration of 4 individual trihalomethanes (THM4 (chloroform (TCM, bromodichloromethane (BDCM, dibromochloromethane (DBCM, and bromoform (TBM, MX, and bromate were tested when boiling and filtering high bromine-containing tap water from Barcelona. For filtering, we used a pitcher-type filter and a household reverse osmosis filter; for boiling, an electric kettle, a saucepan, and a microwave were used. Samples were taken before and after each treatment to determine the change in the DBP concentration. pH, conductivity, and free/total chlorine were also measured. A large decrease of THM4 (from 48% to 97% and MX concentrations was observed for all experiments. Bromine-containing trihalomethanes were mostly eliminated when filtering while chloroform when boiling. There was a large decrease in the concentration of bromate with reverse osmosis, but there was a little effect in the other experiments. These findings suggest that the exposure to THM4 and MX through ingestion is reduced when using these household appliances, while the decrease of bromate is device dependent. This needs to be considered in the exposure assessment of the epidemiological studies.

  14. Retention of iron and zinc in yam flour and boiled yam processed from white yam (D. rotundata) varieties.

    Science.gov (United States)

    Maziya-Dixon, Busie; Alamu, Emmanuel Oladeji; Dufie Wireko-Manu, Faustina; Robert, Asiedu

    2017-05-01

    This study investigated the impact of processing on retention of iron and zinc in D. rotundata. Fresh tubers were processed into boiled yam and yam flour and analyzed for zinc, iron, and physicochemical properties. Percent true retention (%TR) was assessed using paired samples and a formula that compensated for loss or gain of moisture and soluble solids. The retention of iron ranged from 55.5% to 98.7% in boiled yam and 25.2% to 54.9% in yam flour; retention of zinc ranged from 49.3% to 97.5% in boiled yam and 18. 9% to 43.1% in yam flour. The amount of iron retained in boiled yam correlated with the amount in the fresh samples (r = .79), likewise in yam flour (r = .82). A similar trend was observed for zinc. From our study, we conclude that retention of iron and zinc is dependent on the variety and processing method used. The information from this study can be used by food scientists and nutritionists in choosing the appropriate processing to increase the retention of high levels of micronutrient in yams and by the yam breeders to adjust their germplasm breeding activities.

  15. The Effect of Different Boiling and Filtering Devices on the Concentration of Disinfection By-Products in Tap Water

    Science.gov (United States)

    Carrasco-Turigas, Glòria; Villanueva, Cristina M.; Goñi, Fernando; Rantakokko, Panu; Nieuwenhuijsen, Mark J.

    2013-01-01

    Disinfection by-products (DBPs) are ubiquitous contaminants in tap drinking water with the potential to produce adverse health effects. Filtering and boiling tap water can lead to changes in the DBP concentrations and modify the exposure through ingestion. Changes in the concentration of 4 individual trihalomethanes (THM4) (chloroform (TCM), bromodichloromethane (BDCM), dibromochloromethane (DBCM), and bromoform (TBM)), MX, and bromate were tested when boiling and filtering high bromine-containing tap water from Barcelona. For filtering, we used a pitcher-type filter and a household reverse osmosis filter; for boiling, an electric kettle, a saucepan, and a microwave were used. Samples were taken before and after each treatment to determine the change in the DBP concentration. pH, conductivity, and free/total chlorine were also measured. A large decrease of THM4 (from 48% to 97%) and MX concentrations was observed for all experiments. Bromine-containing trihalomethanes were mostly eliminated when filtering while chloroform when boiling. There was a large decrease in the concentration of bromate with reverse osmosis, but there was a little effect in the other experiments. These findings suggest that the exposure to THM4 and MX through ingestion is reduced when using these household appliances, while the decrease of bromate is device dependent. This needs to be considered in the exposure assessment of the epidemiological studies. PMID:23476675

  16. The effect of heating direction on flow boiling heat transfer of R134a in micro-channels

    Science.gov (United States)

    Xu, Mingchen; Jia, Li; Dang, Chao; Peng, Qi

    2017-04-01

    This paper presents effects of heating directions on heat transfer performance of R134a flow boiling in micro- channel heat sink. The heat sink has 30 parallel rectangular channels with cross-sectional dimensions of 500μm width 500μm depth and 30mm length. The experimental operation condition ranges of the heat flux and the mass flux were 13.48 to 82.25 W/cm2 and 373.3 to 1244.4 kg/m2s respectively. The vapor quality ranged from 0.07 to 0.93. The heat transfer coefficients of top heating and bottom heating both were up to 25 kW/m2 K. Two dominate transfer mechanisms of nucleate boiling and convection boiling were observed according to boiling curves. The experimental results indicated that the heat transfer coefficient of bottom heating was 13.9% higher than top heating in low heat flux, while in high heat flux, the heat transfer coefficient of bottom heating was 9.9%.higher than the top heating, because bubbles were harder to divorce the heating wall. And a modified correlation was provided to predict heat transfer of top heating.

  17. High-pressure high-temperature phase diagram of organic crystal paracetamol

    Science.gov (United States)

    Smith, Spencer J.; Montgomery, Jeffrey M.; Vohra, Yogesh K.

    2016-01-01

    High-pressure high-temperature (HPHT) Raman spectroscopy studies have been performed on the organic crystal paracetamol in a diamond anvil cell utilizing boron-doped heating diamond anvil. Isobaric measurements were conducted at pressures up to 8.5 GPa and temperature up to 520 K in five different experiments. Solid state phase transitions from monoclinic Form I  →  orthorhombic Form II were observed at various pressures and temperatures as well as transitions from Form II  →  unknown Form IV. The melting temperature for paracetamol was observed to increase with increasing pressures to 8.5 GPa. This new data is combined with previous ambient temperature high-pressure Raman and x-ray diffraction data to create the first HPHT phase diagram of paracetamol.

  18. Measuring radon reduction in xenon boil-off gas

    Energy Technology Data Exchange (ETDEWEB)

    Bruenner, Stefan; Cichon, Dominick; Lindemann, Sebastian; Marrodan Undagoitia, Teresa; Simgen, Hardy [MPIK, Heidelberg (Germany)

    2016-07-01

    {sup 222}Rn, which originates from the decay of primordial {sup 238}U, is one of the major background sources for ultra-low background noble gas detectors. One of them is XENON1T, which is a dark matter direct detection experiment looking for hypothetical weakly interacting massive particles (WIMPs). It uses liquid xenon (LXe) as a detection medium and aims to be sensitive to spin-independent WIMP-nucleon cross-sections of σ∝2.10{sup -47} cm{sup 2} at a WIMP mass of ∝50 GeV/c{sup 2}. To achieve this goal, radon activity inside the detector must be limited to a few mBq/kg. One possible way for reducing the concentration of {sup 222}Rn inside such an LXe detector is using the so-called ''boil-off method''. It takes advantage of the fact, that the radon concentration in boil-off xenon is smaller compared to the concentration in the liquid xenon from which the boil-off xenon evaporated. This can be understood by the different vapor pressures of radon and xenon. In this talk, tests conducted at the MPIK are outlined which probe the feasibility and effectiveness of the boil-off method. The results prove, that a reduction of the radon concentration can indeed be achieved. In addition, an outlook for possible future applications of this technique is given.

  19. How long does it take to boil an egg? Revisited

    Energy Technology Data Exchange (ETDEWEB)

    Buay, D [Natural Sciences and Science Education, National Institute of Education, Nanyang Technological University, 1, Nanyang Walk, Singapore 637616 (Singapore); Foong, S K [Natural Sciences and Science Education, National Institute of Education, Nanyang Technological University, 1, Nanyang Walk, Singapore 637616 (Singapore); Kiang, D [Department of Physics, Chinese University of Hong Kong, Shatin, New Territories, Hong Kong (China); Kuppan, L [Natural Sciences and Science Education, National Institute of Education, Nanyang Technological University, 1, Nanyang Walk, Singapore 637616 (Singapore); Centre for Research in Pedagogy and Practice, National Institute of Education, Nanyang Technological University, 1, Nanyang Walk, Singapore 637616 (Singapore); Liew, V H [Natural Sciences and Science Education, National Institute of Education, Nanyang Technological University, 1, Nanyang Walk, Singapore 637616 (Singapore)

    2006-01-01

    How long does it take to boil an egg? Theoretical prediction, based on a simple adaptation of the solution to the exact thermal diffusion equation for a sphere, is consistent with experiments. The experimental data are also used to estimate an average value for the thermal diffusivity of an egg.

  20. Boiling heat transfer and droplet spreading of nanofluids.

    Science.gov (United States)

    Murshed, S M Sohel; de Castro, C A Nieto

    2013-11-01

    Nanofluids- a new class of heat transfer fluids have recently been a very attractive area of research due to their fascinating thermophysical properties and numerous potential benefits and applications in many important fields. However, there are many controversies and inconsistencies in reported arguments and experimental results on various thermal characteristics such as effective thermal conductivity, convective heat transfer coefficient and boiling heat transfer rate of nanofluids. As of today, researchers have mostly focused on anomalous thermal conductivity of nanofluids. Although investigations on boiling and droplet spreading are very important for practical application of nanofluids as advanced coolants, considerably fewer efforts have been made on these thermal features of nanofluids. In this paper, recent research and development in boiling heat transfer and droplet spreading of nanofluids are reviewed together with summarizing most related patents on nanofluids published in literature. Review reveals that despite some inconsistent results nanofluids exhibit significantly higher boiling heat transfer performance compared to their base fluids and show great promises to be used as advanced heat transfer fluids in numerous applications. However, there is a clear lack of in-depth understanding of heat transport mechanisms during phase change of nanofluids. It is also found that the nanofluids related patents are limited and among them most of the patents are based on thermal conductivity enhancement and synthesising processes of specific type of nanofluids.

  1. Geologic Controls of Sand Boil Formation at Buck Chute, Mississippi

    Science.gov (United States)

    2017-06-30

    Geology ........................................................................................................................... 4 2.3 Description of...18 3.1 Geology of the Lower Mississippi River Valley...Hypothesis Sand boil formation at the Buck Chute site is the result of geology consisting of point bar and abandoned channel deposits with a thin

  2. Investigation Status of Heat Exchange while Boiling Hydrocarbon Fuel

    Directory of Open Access Journals (Sweden)

    D. S. Obukhov

    2006-01-01

    Full Text Available The paper contains analysis of heat exchange investigations while boiling hydrocarbon fuel. The obtained data are within the limits of the S.S. Kutateladze dependence proposed in 1939. Heat exchange at non-stationary heat release has not been investigated. The data for hydrocarbon fuel with respect to critical density of heat flow are not available even for stationary conditions.

  3. High-performance organic transistors for printed circuits

    Science.gov (United States)

    Takeya, J.

    2014-10-01

    This presentation focuses on recent development of key technologies for printed LSIs which can provide future low-cost platforms for RFID tags, AD converters, data processors, and sensing circuitries. Such prospect bears increasing reality because of recent research innovations in the field of material chemistry, charge transport physics, and solution processes of printable organic semiconductors. Achieving band transport in state-of-the-art printable organic semiconductors, carrier mobility is elevated above 15 cm2/Vs, so that reasonable speed in moderately integrated logic circuits can be available. With excellent chemical and thermal stability for such compounds, we are developing simple integrated devices based on CMOS using p-type and n-type printed organic FETs. Particularly important are new processing technologies for continuous growth of inch-size organic single-crystalline semiconductor "wafers" from solution and for lithographical patterning of semiconductors and metal electrodes. Successful rectification and identification are demonstrated at 13.56 MHz with printed organic CMOS circuits for the first time.

  4. 77 FR 36014 - Initial Test Program of Emergency Core Cooling Systems for Boiling-Water Reactors

    Science.gov (United States)

    2012-06-15

    ... COMMISSION Initial Test Program of Emergency Core Cooling Systems for Boiling-Water Reactors AGENCY: Nuclear...-1277, ``Initial Test Program of Emergency Core Cooling Systems for Boiling- Water Reactors.'' This... testing features of emergency core cooling systems (ECCSs) for boiling-water reactors (BWRs). DATES...

  5. 76 FR 78096 - U.S. Advanced Boiling Water Reactor Aircraft Impact Design Certification Amendment

    Science.gov (United States)

    2011-12-16

    ... COMMISSION 10 CFR Part 52 RIN 3150-AI84 U.S. Advanced Boiling Water Reactor Aircraft Impact Design.... Advanced Boiling Water Reactor (U.S. ABWR) standard plant design to comply with the NRC's aircraft impact...--Design Certification Rule for the U.S. Advanced Boiling Water Reactor IV. Section-by-Section Analysis A...

  6. 77 FR 38338 - Dairyland Power Cooperative; La Crosse Boiling Water Reactor Exemption From Certain Security...

    Science.gov (United States)

    2012-06-27

    ... COMMISSION Dairyland Power Cooperative; La Crosse Boiling Water Reactor Exemption From Certain Security Requirements 1.0 Background The La Crosse Boiling Water Reactor (LACBWR) is owned and was operated by the..., which utilized a forced-circulation, direct-cycle boiling water reactor as its heat source. The plant is...

  7. 76 FR 3540 - U.S. Advanced Boiling Water Reactor Aircraft Impact Design Certification Amendment

    Science.gov (United States)

    2011-01-20

    ... COMMISSION 10 CFR Part 52 RIN 3150-AI84 U.S. Advanced Boiling Water Reactor Aircraft Impact Design... the U.S. Advanced Boiling Water Reactor (ABWR) standard plant design to comply with the NRC's aircraft...--Design Certification Rule for the U.S. Advanced Boiling Water Reactor IV. Section-by-Section Analysis A...

  8. Microbial biogeochemistry of Boiling Springs Lake: a physically dynamic, oligotrophic, low-pH geothermal ecosystem.

    Science.gov (United States)

    Siering, P L; Wolfe, G V; Wilson, M S; Yip, A N; Carey, C M; Wardman, C D; Shapiro, R S; Stedman, K M; Kyle, J; Yuan, T; Van Nostrand, J D; He, Z; Zhou, J

    2013-07-01

    Boiling Springs Lake (BSL) in Lassen Volcanic National Park, California, is North America's largest hot spring, but little is known about the physical, chemical, and biological features of the system. Using a remotely operated vessel, we characterized the bathymetry and near-surface temperatures at sub-meter resolution. The majority of the 1.2 ha, pH 2.2 lake is 10 m deep and 50-52 °C, but temperatures reach 93 °C locally. We extracted DNA from water and sediments collected from warm (52 °C) and hot (73-83 °C) sites separated by 180 m. Gene clone libraries and functional gene microarray (GeoChip 3.0) were used to investigate the BSL community, and uptake of radiolabeled carbon sources was used to assess the relative importance of heterotrophic vs. autotrophic production. Microbial assemblages are similar in both sites despite the strong temperature differential, supporting observations of a dynamic, convectively mixed system. Bacteria in the Actinobacteria and Aquificales phyla are abundant in the water column, and Archaea distantly related to known taxa are abundant in sediments. The functional potential appears similar across a 5-year time span, indicating a stable community with little inter-annual variation, despite the documented seasonal temperature cycle. BSL water-derived DNA contains genes for complete C, N, and S cycles, and low hybridization to probes for N and S oxidation suggests that reductive processes dominate. Many of the detected genes for these processes were from uncultivated bacteria, suggesting novel organisms are responsible for key ecosystem services. Selection imposed by low nutrients, low pH, and high temperature appear to result in low diversity and evenness of genes for key functions involved in C, N, and S cycling. Conversely, organic degradation genes appear to be functionally redundant, and the rapid assimilation of radiolabeled organic carbon into BSL cells suggests the importance of allochthonous C fueling heterotrophic

  9. Phosphorescent organic light emitting diodes with high efficiency and brightness

    Science.gov (United States)

    Forrest, Stephen R; Zhang, Yifan

    2015-11-12

    An organic light emitting device including a) an anode; b) a cathode; and c) an emissive layer disposed between the anode and the cathode, the emissive layer comprising an organic host compound and a phosphorescent compound exhibiting a Stokes Shift overlap greater than 0.3 eV. The organic light emitting device may further include a hole transport layer disposed between the emissive layer and the anode; and an electron transport layer disposed between the emissive layer and the cathode. In some embodiments, the phosphorescent compound exhibits a phosphorescent lifetime of less than 10 .mu.s. In some embodiments, the concentration of the phosphorescent compound ranges from 0.5 wt. % to 10 wt. %.

  10. Microwave-Assisted Superheating and/or Microwave-Specific Superboiling (Nucleation-Limited Boiling of Liquids Occurs under Certain Conditions but is Mitigated by Stirring

    Directory of Open Access Journals (Sweden)

    Anthony Ferrari

    2015-12-01

    Full Text Available Temporary superheating and sustained nucleation-limited “superboiling” of unstirred liquids above the normal atmospheric boiling point have been documented during microwave heating. These phenomena are reliably observed under prescribed conditions, although the duration (of superheating and magnitude (of superheating and superboiling vary according to system parameters such as volume of the liquid and the size and shape of the vessel. Both phenomena are mitigated by rapid stirring with an appropriate stir bar and/or with the addition of boiling chips, which provide nucleation sites to support the phase-change from liquid to gas. With proper experimental design and especially proper stirring, the measured temperature of typical organic reaction mixtures heated at reflux will be close to the normal boiling point temperature of the solvent, whether heated using microwave radiation or conventional convective heat transfer. These observations are important to take into consideration when comparing reaction rates under conventional and microwave heating.

  11. Numerical Investigation of Microgravity Tank Pressure Rise Due to Boiling

    Science.gov (United States)

    Hylton, Sonya; Ibrahim, Mounir; Kartuzova, Olga; Kassemi, Mohammad

    2015-01-01

    The ability to control self-pressurization in cryogenic storage tanks is essential for NASAs long-term space exploration missions. Predictions of the tank pressure rise in Space are needed in order to inform the microgravity design and optimization process. Due to the fact that natural convection is very weak in microgravity, heat leaks into the tank can create superheated regions in the liquid. The superheated regions can instigate microgravity boiling, giving rise to pressure spikes during self-pressurization. In this work, a CFD model is developed to predict the magnitude and duration of the microgravity pressure spikes. The model uses the Schrage equation to calculate the mass transfer, with a different accommodation coefficient for evaporation at the interface, condensation at the interface, and boiling in the bulk liquid. The implicit VOF model was used to account for the moving interface, with bounded second order time discretization. Validation of the models predictions was carried out using microgravity data from the Tank Pressure Control Experiment, which flew aboard the Space Shuttle Mission STS-52. Although this experiment was meant to study pressurization and pressure control, it underwent boiling during several tests. The pressure rise predicted by the CFD model compared well with the experimental data. The ZBOT microgravity experiment is scheduled to fly on February 2016 aboard the ISS. The CFD model was also used to perform simulations for setting parametric limits for the Zero-Boil-Off Tank (ZBOT) Experiments Test Matrix in an attempt to avoid boiling in the majority of the test runs that are aimed to study pressure increase rates during self-pressurization. *Supported in part by NASA ISS Physical Sciences Research Program, NASA HQ, USA

  12. Experimental Investigation of Pool Boiling Heat Transfer Enhancement in Microgravity in the Presence of Electric Fields

    Science.gov (United States)

    Herman, Cila

    1999-01-01

    In boiling high heat fluxes are possible driven by relatively small temperature differences, which make its use increasingly attractive in aerospace applications. The objective of the research is to develop ways to overcome specific problems associated with boiling in the low gravity environment by substituting the buoyancy force with the electric force to enhance bubble removal from the heated surface. Previous studies indicate that in terrestrial applications nucleate boiling heat transfer can be increased by a factor of 50, as compared to values obtained for the same system without electric fields. The goal of our research is to experimentally explore the mechanisms responsible for EHD heat transfer enhancement in boiling in low gravity conditions, by visualizing the temperature distributions in the vicinity of the heated surface and around the bubble during boiling using real-time holographic interferometry (HI) combined with high-speed cinematography. In the first phase of the project the influence of the electric field on a single bubble is investigated. Pool boiling is simulated by injecting a single bubble through a nozzle into the subcooled liquid or into the thermal boundary layer developed along the flat heater surface. Since the exact location of bubble formation is known, the optical equipment can be aligned and focused accurately, which is an essential requirement for precision measurements of bubble shape, size and deformation, as well as the visualization of temperature fields by HI. The size of the bubble and the frequency of bubble departure can be controlled by suitable selection of nozzle diameter and mass flow rate of vapor. In this approach effects due to the presence of the electric field can be separated from effects caused by the temperature gradients in the thermal boundary layer. The influence of the thermal boundary layer can be investigated after activating the heater at a later stage of the research. For the visualization experiments a

  13. Estimating the physicochemical properties of polyhalogenated aromatic and aliphatic compounds using UPPER: part 1. Boiling point and melting point.

    Science.gov (United States)

    Admire, Brittany; Lian, Bo; Yalkowsky, Samuel H

    2015-01-01

    The UPPER (Unified Physicochemical Property Estimation Relationships) model uses enthalpic and entropic parameters to estimate 20 biologically relevant properties of organic compounds. The model has been validated by Lian and Yalkowsky on a data set of 700 hydrocarbons. The aim of this work is to expand the UPPER model to estimate the boiling and melting points of polyhalogenated compounds. In this work, 19 new group descriptors are defined and used to predict the transition temperatures of an additional 1288 compounds. The boiling points of 808 and the melting points of 742 polyhalogenated compounds are predicted with average absolute errors of 13.56 K and 25.85 K, respectively. Copyright © 2014 Elsevier Ltd. All rights reserved.

  14. Highly porous organic polymers bearing tertiary amine group and their exceptionally high CO2 uptake capacities

    Science.gov (United States)

    Gomes, Ruth; Bhaumik, Asim

    2015-02-01

    We report a very simple and unique strategy for synthesis of a tertiary amine functionalized high surface area porous organic polymer (POP) PDVTA-1 through the co-polymerization of monomers divinylbenzene (DVB) and triallylamine (TAA) under solvothermal reaction conditions. Two different PDVTA-1 samples have been synthesized by varying the molar ratio of the monomers. The porous polymeric materials have been thoroughly characterized by solid state 13C CP MAS-NMR, FT-IR and UV-vis spectroscopy, N2 sorption, HR TEM and FE SEM to understand its chemical environment, nanostructure, bonding, morphology and related surface properties. PDVTA-1 with higher amine content (DVB/TAA=4.0) showed exceptionally high CO2 uptake capacity of 85.8 wt% (19.5 mmol g-1) at 273 K and 43.69 wt% (9.93 mmol g-1) at 298 K under 3 bar pressure, whereas relatively low amine loaded material (DVB/TAA=7.0) shows uptake capacity of 59.2 wt% (13.45 mmol g-1) at 273 K and 34.36 wt% (7.81 mmol g-1) at 298 K. Highly porous nanostructure together with very high surface area and basicity at the surface due to the presence of abundant basic tertiary amine N-sites in the framework of PDVTA-1 could be responsible for very high CO2 adsorption.

  15. Oxygen as a promoter for efficient degradation of organic pollutants by high-temperature and high-pressure electrochemistry.

    Science.gov (United States)

    Zhou, Minghua; Lei, Lecheng; Dai, Qizhou

    2007-07-07

    The introduction of oxygen in electrochemical oxidation at relatively high temperature and pressure as a promoter resulting in synergetic effects, greatly improves the mineralization of high-concentrated organic pollutants.

  16. Overview and Computational Approach for Studying the Physicochemical Characterization of High-Boiling-Point Petroleum Fractions (350°C+ Approche informatique pour l’étude des propriétés physico-chimiques de fraction pétrolière lourde (350°C+

    Directory of Open Access Journals (Sweden)

    Plazas Tovar L.

    2012-06-01

    Full Text Available The processing and upgrading of high-boilingpoint petroleum fractions, containing a large number of components from different groups (paraffins, olefins, naphthenes, aromatics require an in-depth evaluation. In order to characterize them, their thermodynamic and thermophysical properties must be determined. This work presents a computational approach based on the breakdown of the petroleum fraction into pseudocomponents defined by a trial-and-error exercise in which the mass- and molar-balance errors were minimized. Cases studies are illustrated to three heavy residues 400°C+ from “W, Y and Z” crude oil. This procedure requires the boiling point distillation curve and the density of the whole fraction as the input bulk properties. The methods proposed according to available correlations in the literature and standard industrial methods were mainly used to estimate properties that include the basic properties (normal boiling point, density and Watson factor characterization, the thermodynamic properties (molar mass and critical properties and the thermophysical and transport properties (kinematic viscosity, thermal conductivity, specific heat capacity and vapor pressure. The methodology developed has shown to be a useful tool for calculating a remarkably broad range of physicochemical properties of high-boiling-point petroleum fractions with good accuracy when the bulk properties are available, since computational approach gave an overall absolute deviation lower than 10% when compared with the experimental results obtained in the research laboratories LDPS/LOPCA/UNICAMP. Le traitement et la valorisation des fractions pétrolières lourdes nécessitent une étude très détaillée dans la mesure où le pétrole contient un très grand nombre de composants différents (paraffines, oléfines, naphtènes, arômes. Afin de caractériser les fractions, il est indispensable de déterminer les propriétés thermodynamiques et thermophysiques des

  17. 高强度聚焦超声辐照离体组织中空化泡和沸腾泡对辐照后即刻B超声像图中强回声的贡献%Contribution of cavitation and boiling bubbles to hyperecho in B-mode ultrasound images immediately after in vitro tissue exposed to high intensity focused ultrasound

    Institute of Scientific and Technical Information of China (English)

    艾慧坚; 钟明松; 李发琪; 王彬; 易华容; 王琦; 王智彪

    2012-01-01

    [目的]研究高强度聚焦超声(high intensity focused ultrasound,HIFU)辐照离体牛肝组织中的空化泡和沸腾泡对辐照后即刻B超声像图中强回声的贡献.[方法]将牛肝组织简单随机分成2组,每组20块.一组使用200W声功率的HIFU辐照2s,以在HIFU焦域处只产生空化泡,另一组使用50W声功率的HIFU辐照80s,以在焦域处只产生沸腾泡.在辐照过程中,使用置于HIFU声焦点旁1mm的热电偶对焦域处的温度进行测量,并通过计算机的RS232串口进行记录.同时,使用被动空化检测(passive cavitation detection,PCD)系统测取牛肝组织内传播出的声信号,并在LabVIEW开发平台上编程以获得该信号的频谱,计算该频谱在3~7MHz内滤除谐波后的均方根值(root mean square,RMS).记录HIFU辐照后即刻的B超声像图,与辐照前同一位置的声像图进行比较.辐照结束后将牛肝切开,观察是否有损伤形成.[结果]200W声功率的HIFU辐照离体牛肝组织后即刻B超声像图中有19次未出现强同声,PCD系统所检测信号的频谱中出现明显的宽带噪声,辐照开始后RMS增大,焦点处的最高温度为(61.10±6.18)℃.50W声功率的HIFU辐照离体牛肝组织后即刻B超声像图中有19次出现强回声,PCD系统所测信号频谱中未见宽带噪声,RMS未见增大,焦域处的最高温度为(93.34±3.37)℃.辐照后,所有牛肝组织中均出现了凝固性坏死.[结论]HIFU辐照后即刻B超声像图中强回声出现的主要原因是辐照过程中产生的沸腾泡,非空化泡.%Objective To study the contribution of cavitation and boiling bubbles to hyperecho in B-mode ultrasound images immediately after in vitro bovine liver tissue exposed to high intensity focused ultrasound (HIFU). Methods Forty bovine liver tissue blocks were divided into group A and group B, 20 in each group. Group A was exposed to 200 W acoustic power HIFU for 2 s to induce cavitation bubbles in the focal region of HIFU and group B

  18. CHF Phenomena by Photographic Study of Boiling Behavior due to Transient Heat Inputs

    OpenAIRE

    Jongdoc Park; Katsuya Fukuda; Qiusheng Liu

    2012-01-01

    The transient boiling heat transfer characteristics in a pool of water and highly wetting liquids such as ethanol and FC-72 due to an exponentially increasing heat input of various rates were investigated using the 1.0 mm diameter experimental heater shaped in a horizontal cylinder for wide ranges of pressure and subcooling. The trend of critical heat flux (CHF) values in relation to the periods was divided into three groups. The CHF belonging to the 1st group with a longer period occurs with...

  19. Pool film boiling from rotating and stationary spheres in liquid nitrogen. [for SSME turbopump ball bearings

    Science.gov (United States)

    Cuan, Winston M.; Schwartz, Sidney H.

    1988-01-01

    Results are presented for a preliminary experiment involving a saturated pool boiling at 1 atm from rotating 2 and 3 inch diameter spheres which were immersed in LN2. Additional results are presented for a stationary 2 inch diameter sphere quenched in LN2, which were obtained with a more versatile and complete experimental apparatus. The speed of the rotational tests varied from 0 to 10,000 rpm. The stationary experiments parametrically varied pressure and subcooling levels from 0 to 600 psig and from 0 to 50 F, respectively. During the rotational tests, a high speed photographic analysis was undertaken to measure the thickness of the vapor film surrounding the sphere.

  20. Zero Boil Off Cryogen Storage for Future Launchers

    Science.gov (United States)

    Valentian, D.; Plachta, D.; Kittel, P.; Hastings, L. J.; Salerno, Louis J.; Arnold, James O. (Technical Monitor)

    2001-01-01

    Zero boil off (ZBO) cryogen storage using both cryocoolers and passive insulation technologies will enable long-term exploration missions by allowing designers to optimize tankage without the need for excess cryogen storage to account for boil off. Studies of ZBO (zero boil off) have been on-going in the USA for several years. More recently, a review of the needs of advanced space propulsion took place in Europe. This showed the interest of the European community in cryogenic propulsion for planetary missions as well as the use of liquid hydrogen for large power electric propulsion (manned Mars missions). Although natural boiling could be acceptable for single leg missions, passive insulation techniques yield roughly a I% per month cryogen loss and this would not be cost effective for robotic planetary missions involving storage times greater than one year. To make economic sense, long-term exploration missions require lower tank capacity and longer storage times. Recent advances in cryocooler technology, resulting in vast improvements in both cooler efficiency and reliability, make ZBO is a clear choice for planetary exploration missions. Other, more near term applications of ZBO include boil-off reduction or elimination applied to first and upper stages of future earth-to-orbit (ETO) launchers. This would extend launch windows and reduce infrastructure costs. Successors to vehicles like Ariane 5 could greatly benefit by implementing ZBO. Zero Boil Off will only be successful in ETO launcher applications if it makes economic sense to implement. The energy cost is only a fraction of the total cost of buying liquid cryogen, the rest being transportation and other overhead. Because of this, higher boiling point cryogens will benefit more from on-board liquefaction, thus reducing the infrastructure costs. Since hydrogen requires a liquefier with at least a 17% efficiency just to break even from a cost standpoint, one approach for implementing ZBO in upper stages would