WorldWideScience

Sample records for high bandwidth active

  1. Performance Evaluation of a High Bandwidth Liquid Fuel Modulation Valve for Active Combustion Control

    Science.gov (United States)

    Saus, Joseph R.; DeLaat, John C.; Chang, Clarence T.; Vrnak, Daniel R.

    2012-01-01

    At the NASA Glenn Research Center, a characterization rig was designed and constructed for the purpose of evaluating high bandwidth liquid fuel modulation devices to determine their suitability for active combustion control research. Incorporated into the rig s design are features that approximate conditions similar to those that would be encountered by a candidate device if it were installed on an actual combustion research rig. The characterized dynamic performance measures obtained through testing in the rig are planned to be accurate indicators of expected performance in an actual combustion testing environment. To evaluate how well the characterization rig predicts fuel modulator dynamic performance, characterization rig data was compared with performance data for a fuel modulator candidate when the candidate was in operation during combustion testing. Specifically, the nominal and off-nominal performance data for a magnetostrictive-actuated proportional fuel modulation valve is described. Valve performance data were collected with the characterization rig configured to emulate two different combustion rig fuel feed systems. Fuel mass flows and pressures, fuel feed line lengths, and fuel injector orifice size was approximated in the characterization rig. Valve performance data were also collected with the valve modulating the fuel into the two combustor rigs. Comparison of the predicted and actual valve performance data show that when the valve is operated near its design condition the characterization rig can appropriately predict the installed performance of the valve. Improvements to the characterization rig and accompanying modeling activities are underway to more accurately predict performance, especially for the devices under development to modulate fuel into the much smaller fuel injectors anticipated in future lean-burning low-emissions aircraft engine combustors.

  2. Network Bandwidth Utilization Forecast Model on High Bandwidth Network

    Energy Technology Data Exchange (ETDEWEB)

    Yoo, Wucherl; Sim, Alex

    2014-07-07

    With the increasing number of geographically distributed scientific collaborations and the scale of the data size growth, it has become more challenging for users to achieve the best possible network performance on a shared network. We have developed a forecast model to predict expected bandwidth utilization for high-bandwidth wide area network. The forecast model can improve the efficiency of resource utilization and scheduling data movements on high-bandwidth network to accommodate ever increasing data volume for large-scale scientific data applications. Univariate model is developed with STL and ARIMA on SNMP path utilization data. Compared with traditional approach such as Box-Jenkins methodology, our forecast model reduces computation time by 83.2percent. It also shows resilience against abrupt network usage change. The accuracy of the forecast model is within the standard deviation of the monitored measurements.

  3. High-Bandwidth Hybrid Sensor (HYSENS) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — ATA has demonstrated the primary innovation of combining a precision MEMS gyro (BAE SiRRS01) with a high bandwidth angular rate sensor, ATA's ARS-14 resulting in a...

  4. VISA IB Ultra-High Bandwidth, High Gain SASE FEL

    CERN Document Server

    Andonian, Gerard; Murokh, Alex; Pellegrini, Claudio; Reiche, Sven; Rosenzweig, J B; Travish, Gil

    2004-01-01

    The results of a high energy-spread SASE FEL experiment, the intermediary experiment linking the VISA I and VISA II projects, are presented. A highly chirped beam (~1.7%) was transported without correction of longitudinal aberrations in the ATF dogleg, and injected into the VISA undulator. The output FEL radiation displayed an uncharacteristicly large bandwidth (~11%) with extremely stable lasing and measured energy of about 2 microJoules. Start-to-end simulations reproduce key features of the measured results and provide an insight into the mechanisms giving rise to such a high bandwidth. These analyses are described as they relate to important considerations for the VISA II experiment.

  5. Fast Faraday Cup With High Bandwidth

    Science.gov (United States)

    Deibele, Craig E [Knoxville, TN

    2006-03-14

    A circuit card stripline Fast Faraday cup quantitatively measures the picosecond time structure of a charged particle beam. The stripline configuration maintains signal integrity, and stitching of the stripline increases the bandwidth. A calibration procedure ensures the measurement of the absolute charge and time structure of the charged particle beam.

  6. On the Bandwidth of High-Impedance Frequency Selective Surfaces

    CERN Document Server

    Costa, Filippo; Monorchio, Agostino; 10.1109/LAWP.2009.2038346

    2010-01-01

    In this letter, the bandwidth of high-impedance surfaces (HISs) is discussed by an equivalent circuit approach. Even if these surfaces have been employed for almost 10 years, it is sometimes unclear how to choose the shape of the frequency selective surface (FSS) on the top of the grounded slab in order to achieve the largest possible bandwidth. Here, we will show that the conventional approach describing the HIS as a parallel connection between the inductance given by the grounded dielectric substrate and the capacitance of the FSS may induce inaccurate results in the determination of the operating bandwidth of the structure. Indeed, in order to derive a more complete model and to provide a more accurate estimate of the operating bandwidth, it is also necessary to introduce the series inductance of the FSS.We will present the explicit expression for defining the bandwidth of a HIS, and we will show that the reduction of the FSS inductance results in the best choice for achieving wide operating bandwidth in c...

  7. High-bandwidth hybrid quantum repeater.

    Science.gov (United States)

    Munro, W J; Van Meter, R; Louis, Sebastien G R; Nemoto, Kae

    2008-07-25

    We present a physical- and link-level design for the creation of entangled pairs to be used in quantum repeater applications where one can control the noise level of the initially distributed pairs. The system can tune dynamically, trading initial fidelity for success probability, from high fidelity pairs (F=0.98 or above) to moderate fidelity pairs. The same physical resources that create the long-distance entanglement are used to implement the local gates required for entanglement purification and swapping, creating a homogeneous repeater architecture. Optimizing the noise properties of the initially distributed pairs significantly improves the rate of generating long-distance Bell pairs. Finally, we discuss the performance trade-off between spatial and temporal resources.

  8. Simple High-Bandwidth Sideband Locking with Heterodyne Readout

    CERN Document Server

    Reinhardt, Christoph; Sankey, Jack C

    2016-01-01

    We present a robust sideband laser locking technique that is ideally suited for applications requiring low probe power and heterodyne readout. By feeding back to a high-bandwidth voltage controlled oscillator, we lock a first-order phase-modulation sideband to a table-top high-finesse Fabry-Perot cavity, achieving a feedback bandwidth of 3.5 MHz with a single integrator, limited fundamentally by the signal delay. The directly measured transfer function of the closed feedback loop agrees with a model assuming ideal system components, and from this we suggest a modified design that should realistically achieve a bandwidth exceeding 6 MHz with a near-causally limited feedback gain of $4\\times 10^7$ at 1 kHz. The off-resonance optical carrier is used for alignment-free heterodyne readout, alleviating the need for a second laser or additional optical modulators.

  9. High speed and wide bandwidth delta-sigma ADCs

    CERN Document Server

    Bolatkale, Muhammed; Makinwa, Kofi A A

    2014-01-01

    This book describes techniques for realizing wide bandwidth (125MHz) over-sampled analog-to-digital converters (ADCs) in nanometer-CMOS processes.  The authors offer a clear and complete picture of system level challenges and practical design solutions in high-speed Delta-Sigma modulators.  Readers will be enabled to implement ADCs as continuous-time delta-sigma (CT∆Σ) modulators, offering simple resistive inputs, which do not require the use of power-hungry input buffers, as well as offering inherent anti-aliasing, which simplifies system integration. The authors focus on the design of high speed and wide-bandwidth ΔΣMs that make a step in bandwidth range which was previously only possible with Nyquist converters. More specifically, this book describes the stability, power efficiency, and linearity limits of ΔΣMs, aiming at a GHz sampling frequency.   • Provides overview of trends in Wide Bandwidth and High Dynamic Range analog-to-digital converters (ADCs); • Enables the design of a wide band...

  10. High-bandwidth remote flat panel display interconnect system

    Science.gov (United States)

    Peterson, Darrel G.

    1999-08-01

    High performance electronic displays (CRT, AMLCD, TFEL, plasma, etc.) require wide bandwidth electrical drive signals to produce the desired display images. When the image generation and/or image processing circuitry is located within the same line replaceable unit (LRU) as the display media, the transmission of the display drive signals to the display media presents no unusual design problems. However, many aircraft cockpits are severely constrained for available space behind the instrument panel. This often forces the system designer to specify that only the display media and its immediate support circuitry are to be mounted in the instrument panel. A wide bandwidth interconnect system is then required to transfer image data from the display generation circuitry to the display unit. Image data transfer rates of nearly 1.5 Gbits/second may be required when displaying full motion video at a 60 Hz field rate. In addition to wide bandwidth, this interconnect system must exhibit several additional key characteristics: (1) Lossless transmission of image data; (2) High reliability and high integrity; (3) Ease of installation and field maintenance; (4) High immunity to HIRF and electrical noise; (5) Low EMI emissions; (6) Long term supportability; and (7) Low acquisition and maintenance cost. Rockwell Collins has developed an avionics grade remote display interconnect system based on the American National Standards Institute Fibre Channel standard which meets these requirements. Readily available low cost commercial off the shelf (COTS) components are utilized, and qualification tests have confirmed system performance.

  11. Managing high-bandwidth real-time data storage

    Energy Technology Data Exchange (ETDEWEB)

    Bigelow, David D. [Los Alamos National Laboratory; Brandt, Scott A [Los Alamos National Laboratory; Bent, John M [Los Alamos National Laboratory; Chen, Hsing-Bung [Los Alamos National Laboratory

    2009-09-23

    There exist certain systems which generate real-time data at high bandwidth, but do not necessarily require the long-term retention of that data in normal conditions. In some cases, the data may not actually be useful, and in others, there may be too much data to permanently retain in long-term storage whether it is useful or not. However, certain portions of the data may be identified as being vitally important from time to time, and must therefore be retained for further analysis or permanent storage without interrupting the ongoing collection of new data. We have developed a system, Mahanaxar, intended to address this problem. It provides quality of service guarantees for incoming real-time data streams and simultaneous access to already-recorded data on a best-effort basis utilizing any spare bandwidth. It has built in mechanisms for reliability and indexing, can scale upwards to meet increasing bandwidth requirements, and handles both small and large data elements equally well. We will show that a prototype version of this system provides better performance than a flat file (traditional filesystem) based version, particularly with regard to quality of service guarantees and hard real-time requirements.

  12. Ultra-high bandwidth quantum secured data transmission

    Science.gov (United States)

    Dynes, James F.; Tam, Winci W.-S.; Plews, Alan; Fröhlich, Bernd; Sharpe, Andrew W.; Lucamarini, Marco; Yuan, Zhiliang; Radig, Christian; Straw, Andrew; Edwards, Tim; Shields, Andrew J.

    2016-10-01

    Quantum key distribution (QKD) provides an attractive means for securing communications in optical fibre networks. However, deployment of the technology has been hampered by the frequent need for dedicated dark fibres to segregate the very weak quantum signals from conventional traffic. Up until now the coexistence of QKD with data has been limited to bandwidths that are orders of magnitude below those commonly employed in fibre optic communication networks. Using an optimised wavelength divisional multiplexing scheme, we transport QKD and the prevalent 100 Gb/s data format in the forward direction over the same fibre for the first time. We show a full quantum encryption system operating with a bandwidth of 200 Gb/s over a 100 km fibre. Exploring the ultimate limits of the technology by experimental measurements of the Raman noise, we demonstrate it is feasible to combine QKD with 10 Tb/s of data over a 50 km link. These results suggest it will be possible to integrate QKD and other quantum photonic technologies into high bandwidth data communication infrastructures, thereby allowing their widespread deployment.

  13. Ultra-high bandwidth quantum secured data transmission

    Science.gov (United States)

    Dynes, James F.; Tam, Winci W-S.; Plews, Alan; Fröhlich, Bernd; Sharpe, Andrew W.; Lucamarini, Marco; Yuan, Zhiliang; Radig, Christian; Straw, Andrew; Edwards, Tim; Shields, Andrew J.

    2016-01-01

    Quantum key distribution (QKD) provides an attractive means for securing communications in optical fibre networks. However, deployment of the technology has been hampered by the frequent need for dedicated dark fibres to segregate the very weak quantum signals from conventional traffic. Up until now the coexistence of QKD with data has been limited to bandwidths that are orders of magnitude below those commonly employed in fibre optic communication networks. Using an optimised wavelength divisional multiplexing scheme, we transport QKD and the prevalent 100 Gb/s data format in the forward direction over the same fibre for the first time. We show a full quantum encryption system operating with a bandwidth of 200 Gb/s over a 100 km fibre. Exploring the ultimate limits of the technology by experimental measurements of the Raman noise, we demonstrate it is feasible to combine QKD with 10 Tb/s of data over a 50 km link. These results suggest it will be possible to integrate QKD and other quantum photonic technologies into high bandwidth data communication infrastructures, thereby allowing their widespread deployment. PMID:27734921

  14. High modulation bandwidth of a light-emitting diode with surface plasmon coupling (Conference Presentation)

    Science.gov (United States)

    Lin, Chun-Han; Tu, Charng-Gan; Yao, Yu-Feng; Chen, Sheng-Hung; Su, Chia-Ying; Chen, Hao-Tsung; Kiang, Yean-Woei; Yang, Chih-Chung

    2017-02-01

    Besides lighting, LEDs can be used for indoor data transmission. Therefore, a large modulation bandwidth becomes an important target in the development of visible LED. In this regard, enhancing the radiative recombination rate of carriers in the quantum wells of an LED is a useful method since the modulation bandwidth of an LED is related to the carrier decay rate besides the device RC time constant To increase the carrier decay rate in an LED without sacrificing its output power, the technique of surface plasmon (SP) coupling in an LED is useful. In this paper, the increases of modulation bandwidth by reducing mesa size, decreasing active layer thickness, and inducing SP coupling in blue- and green-emitting LEDs are illustrated. The results are demonstrated by comparing three different LED surface structures, including bare p-type surface, GaZnO current spreading layer, and Ag nanoparticles (NPs) for inducing SP coupling. In a single-quantum-well, blue-emitting LED with a circular mesa of 10 microns in radius, SP coupling results in a modulation bandwidth of 528.8 MHz, which is believed to be the record-high level. A smaller RC time constant can lead to a higher modulation bandwidth. However, when the RC time constant is smaller than 0.2 ns, its effect on modulation bandwidth saturates. The dependencies of modulation bandwidth on injected current density and carrier decay time confirm that the modulation bandwidth is essentially inversely proportional to a time constant, which is inversely proportional to the square-root of carrier decay rate and injected current density.

  15. Extravehicular Activity Operations Concepts Under Communication Latency and Bandwidth Constraints

    Science.gov (United States)

    Beaton, Kara H.; Chappell, Steven P.; Abercromby, Andrew F. J.; Miller, Matthew J.; Nawotniak, Shannon Kobs; Hughes, Scott; Brady, Allyson; Lim, Darlene S. S.

    2017-01-01

    The Biologic Analog Science Associated with Lava Terrains (BASALT) project is a multi-year program dedicated to iteratively develop, implement, and evaluate concepts of operations (ConOps) and supporting capabilities intended to enable and enhance human scientific exploration of Mars. This pa-per describes the planning, execution, and initial results from the first field deployment, referred to as BASALT-1, which consisted of a series of 10 simulated extravehicular activities (EVAs) on volcanic flows in Idaho's Craters of the Moon (COTM) National Monument. The ConOps and capabilities deployed and tested during BASALT-1 were based on previous NASA trade studies and analog testing. Our primary research question was whether those ConOps and capabilities work acceptably when performing real (non-simulated) biological and geological scientific exploration under 4 different Mars-to-Earth communication conditions: 5 and 15 min one-way light time (OWLT) communication latencies and low (0.512 Mb/s uplink, 1.54 Mb/s downlink) and high (5.0 Mb/s uplink, 10.0 Mb/s downlink) bandwidth conditions representing the lower and higher limits of technical communication capabilities currently proposed for future human exploration missions. The synthesized results of BASALT-1 with respect to the ConOps and capabilities assessment were derived from a variety of sources, including EVA task timing data, network analytic data, and subjective ratings and comments regarding the scientific and operational acceptability of the ConOp and the extent to which specific capabilities were enabling and enhancing, and are presented here. BASALT-1 established preliminary findings that baseline ConOp, software systems, and communication protocols were scientifically and operationally acceptable with minor improvements desired by the "Mars" extravehicular (EV) and intravehicular (IV) crewmembers, but unacceptable with improvements required by the "Earth" Mission Support Center. These data will provide a

  16. Modulator-Based, High Bandwidth Optical Links for HEP Experiments

    CERN Document Server

    Underwood, D G; Fernando, W S; Stanek, R W

    2012-01-01

    As a concern with the reliability, bandwidth and mass of future optical links in LHC experiments, we are investigating CW lasers and light modulators as an alternative to VCSELs. These links will be particularly useful if they utilize light modulators which are very small, low power, high bandwidth, and are very radiation hard. We have constructed a test system with 3 such links, each operating at 10 Gb/s. We present the quality of these links (jitter, rise and fall time, BER) and eye mask margins (10GbE) for 3 different types of modulators: LiNbO3-based, InP-based, and Si-based. We present the results of radiation hardness measurements with up to ~1012 protons/cm2 and ~65 krad total ionizing dose (TID), confirming no single event effects (SEE) at 10 Gb/s with either of the 3 types of modulators. These optical links will be an integral part of intelligent tracking systems at various scales from coupled sensors through intra-module and off detector communication. We have used a Si-based photonic transceiver to...

  17. High speed InAs electron avalanche photodiodes overcome the conventional gain-bandwidth product limit.

    Science.gov (United States)

    Marshall, Andrew R J; Ker, Pin Jern; Krysa, Andrey; David, John P R; Tan, Chee Hing

    2011-11-07

    High bandwidth, uncooled, Indium Arsenide (InAs) electron avalanche photodiodes (e-APDs) with unique and highly desirable characteristics are reported. The e-APDs exhibit a 3dB bandwidth of 3.5 GHz which, unlike that of conventional APDs, is shown not to reduce with increasing avalanche gain. Hence these InAs e-APDs demonstrate a characteristic of theoretically ideal electron only APDs, the absence of a gain-bandwidth product limit. This is important because gain-bandwidth products restrict the maximum exploitable gain in all conventional high bandwidth APDs. Non-limiting gain-bandwidth products up to 580 GHz have been measured on these first high bandwidth e-APDs.

  18. Highly efficient frequency conversion with bandwidth compression of quantum light

    Science.gov (United States)

    Allgaier, Markus; Ansari, Vahid; Sansoni, Linda; Eigner, Christof; Quiring, Viktor; Ricken, Raimund; Harder, Georg; Brecht, Benjamin; Silberhorn, Christine

    2017-01-01

    Hybrid quantum networks rely on efficient interfacing of dissimilar quantum nodes, as elements based on parametric downconversion sources, quantum dots, colour centres or atoms are fundamentally different in their frequencies and bandwidths. Although pulse manipulation has been demonstrated in very different systems, to date no interface exists that provides both an efficient bandwidth compression and a substantial frequency translation at the same time. Here we demonstrate an engineered sum-frequency-conversion process in lithium niobate that achieves both goals. We convert pure photons at telecom wavelengths to the visible range while compressing the bandwidth by a factor of 7.47 under preservation of non-classical photon-number statistics. We achieve internal conversion efficiencies of 61.5%, significantly outperforming spectral filtering for bandwidth compression. Our system thus makes the connection between previously incompatible quantum systems as a step towards usable quantum networks. PMID:28134242

  19. Highly efficient frequency conversion with bandwidth compression of quantum light

    Science.gov (United States)

    Allgaier, Markus; Ansari, Vahid; Sansoni, Linda; Eigner, Christof; Quiring, Viktor; Ricken, Raimund; Harder, Georg; Brecht, Benjamin; Silberhorn, Christine

    2017-01-01

    Hybrid quantum networks rely on efficient interfacing of dissimilar quantum nodes, as elements based on parametric downconversion sources, quantum dots, colour centres or atoms are fundamentally different in their frequencies and bandwidths. Although pulse manipulation has been demonstrated in very different systems, to date no interface exists that provides both an efficient bandwidth compression and a substantial frequency translation at the same time. Here we demonstrate an engineered sum-frequency-conversion process in lithium niobate that achieves both goals. We convert pure photons at telecom wavelengths to the visible range while compressing the bandwidth by a factor of 7.47 under preservation of non-classical photon-number statistics. We achieve internal conversion efficiencies of 61.5%, significantly outperforming spectral filtering for bandwidth compression. Our system thus makes the connection between previously incompatible quantum systems as a step towards usable quantum networks.

  20. Highly efficient frequency conversion with bandwidth compression of quantum light

    CERN Document Server

    Allgaier, Markus; Sansoni, Linda; Quiring, Viktor; Ricken, Raimund; Harder, Georg; Brecht, Benjamin; Silberhorn, Christine

    2016-01-01

    Hybrid quantum networks rely on efficient interfacing of dissimilar quantum nodes, since elements based on parametric down-conversion sources, quantum dots, color centres or atoms are fundamentally different in their frequencies and bandwidths. While pulse manipulation has been demonstrated in very different systems, to date no interface exists that provides both an efficient bandwidth compression and a substantial frequency translation at the same time. Here, we demonstrate an engineered sum-frequency-conversion process in Lithium Niobate that achieves both goals. We convert pure photons at telecom wavelengths to the visible range while compressing the bandwidth by a factor of 7.47 under preservation of non-classical photon-number statistics. We achieve internal conversion efficiencies of 75.5%, significantly outperforming spectral filtering for bandwidth compression. Our system thus makes the connection between previously incompatible quantum systems as a step towards usable quantum networks.

  1. High Bandwidth Short Stroke Rotary Fast Tool Servo

    Energy Technology Data Exchange (ETDEWEB)

    Montesanti, R C; Trumper, D L

    2003-08-22

    This paper presents the design and performance of a new rotary fast tool servo (FTS) capable of developing the 40 g's tool tip acceleration required to follow a 5 micron PV sinusoidal surface at 2 kHz with a planned accuracy of 50 nm, and having a full stroke of 50 micron PV at lower frequencies. Tests with de-rated power supplies have demonstrated a closed-loop unity-gain bandwidth of 2 kHz with 20 g's tool acceleration, and we expect to achieve 40 g's with supplies providing {+-} 16 Amp to the Lorentz force actuator. The use of a fast tool servo with a diamond turning machine for producing non-axisymmetric or textured surfaces on a workpiece is well known. Our new rotary FTS was designed to specifically accommodate fabricating prescription textured surfaces on 5 mm diameter spherical target components for High Energy Density Physics experiments on the National Ignition Facility Laser (NIF).

  2. High-gain, high-bandwidth, rail-to-rail, constant-gm CMOS operational amplifier

    Science.gov (United States)

    Huang, Hong-Yi; Wang, Bo-Ruei

    2013-01-01

    This study presents a high-gain, high-bandwidth, constant-gm , rail-to-rail operational amplifier (op-amp). The constant transconductance is improved with a source-to-bulk bias control of an input pair. A source degeneration scheme is also adapted to the output stage for receiving wide input range without degradation of the gain. Additionally, several compensation schemes are employed to enhance the stability. A test chip is fabricated in a 0.18 µm complementary metal-oxide semiconductor process. The active area of the op-amp is 181 × 173 µm2 and it consumes a power of 2.41 mW at a supply voltage of 1.8 V. The op-amp achieves a dc gain of 94.3 dB and a bandwidth of 45 MHz when the output capacitive load is connected to an effective load of 42.5 pF. A class-AB output stage combining a slew rate (SR) boost circuit provides a sinking current of 6 mA and an SR of 17 V/µs.

  3. An Octave Bandwidth, High PAE, Linear, Class J GaN High Power Amplifier

    Science.gov (United States)

    2012-03-12

    versus the modeled small-signal gain and return loss response of the Class J amplifier using a 45-W CREE GaN HEMT . The amplifier has a gain of 13 to...AFFTC-PA-12055 An Octave Bandwidth, High PAE, Linear, Class J GaN High Power Amplifier Kris Skowronski, Steve Nelson, Rajesh Mongia, Howard...Technical Paper 3. DATES COVERED (From - To) 11/11 – 03/12 (etc.) 4. TITLE AND SUBTITLE An Octave Bandwidth, High PAE, Linear, Class J GaN High

  4. Adaptive slope compensation for high bandwidth digital current mode controller

    DEFF Research Database (Denmark)

    Taeed, Fazel; Nymand, Morten

    2015-01-01

    An adaptive slope compensation method for digital current mode control of dc-dc converters is proposed in this paper. The compensation slope is used for stabilizing the inner current loop in peak current mode control. In this method, the compensation slope is adapted with the variations...... in converter duty cycle. The adaptive slope compensation provides optimum controller operation in term of bandwidth over wide range of operating points. In this paper operation principle of the controller is discussed. The proposed controller is implemented in an FPGA to control a 100 W buck converter...

  5. Ultra-low Noise, High Bandwidth, 1550nm HgCdTe APD Project

    Data.gov (United States)

    National Aeronautics and Space Administration — To meet the demands of future high-capacity free space optical communications links, a high bandwidth, near infrared (NIR), single photon sensitive optoelectronic...

  6. Knee implant imaging at 3 Tesla using high-bandwidth radiofrequency pulses.

    Science.gov (United States)

    Bachschmidt, Theresa J; Sutter, Reto; Jakob, Peter M; Pfirrmann, Christian W A; Nittka, Mathias

    2015-06-01

    To investigate the impact of high-bandwidth radiofrequency (RF) pulses used in turbo spin echo (TSE) sequences or combined with slice encoding for metal artifact correction (SEMAC) on artifact reduction at 3 Tesla in the knee in the presence of metal. Local transmit/receive coils feature increased maximum B1 amplitude, reduced SAR exposition and thus enable the application of high-bandwidth RF pulses. Susceptibility-induced through-plane distortion scales inversely with the RF bandwidth and the view angle, hence blurring, increases for higher RF bandwidths, when SEMAC is used. These effects were assessed for a phantom containing a total knee arthroplasty. TSE and SEMAC sequences with conventional and high RF bandwidths and different contrasts were tested on eight patients with different types of implants. To realize scan times of 7 to 9 min, SEMAC was always applied with eight slice-encoding steps and distortion was rated by two radiologists. A local transmit/receive knee coil enables the use of an RF bandwidth of 4 kHz compared with 850 Hz in conventional sequences. Phantom scans confirm the relation of RF bandwidth and through-plane distortion, which can be reduced up to 79%, and demonstrate the increased blurring for high-bandwidth RF pulses. In average, artifacts in this RF mode are rated hardly visible for patients with joint arthroplasties, when eight SEMAC slice-encoding steps are applied, and for patients with titanium fixtures, when TSE is used. The application of high-bandwidth RF pulses by local transmit coils substantially reduces through-plane distortion artifacts at 3 Tesla. © 2014 Wiley Periodicals, Inc.

  7. Study on Dielectric Resonator Antenna with Annular Patch for High Gain and Large Bandwidth

    Institute of Scientific and Technical Information of China (English)

    FENG Kuisheng; LI Na; MENG Qingwei; WANG Yongfeng; ZHANG Jingwei

    2015-01-01

    A new high-gain cylindrical Dielectric res-onator antenna (DRA) with a large bandwidth is proposed. A cylindrical Dielectric resonator (DR), a double-annular patch and a metallic cylinder are used to obtain a large bandwidth and a high gain. The mode TM12 excited in the patch is used to enhance the gain of the DRA, and the cavity formed by the metallic cylinder provides a further higher gain and a larger bandwidth. The measured results demonstrate that the proposed DRA achieves a large band-width of 23%from 5.3 to 6.8GHz with VSWR less than two and a high gain around 11 dBi.

  8. Novel high bandwidth wall shear stress sensor for ultrasonic cleaning applications

    Science.gov (United States)

    Gonzalez-Avila, S. Roberto; Prabowo, Firdaus; Ohl, Claus-Dieter

    2010-11-01

    Ultrasonic cleaning is due to the action of cavitation bubbles. The details of the cleaning mechanisms are not revealed or confirmed experimentally, yet several studies suggest that the wall shear stresses generated are very high, i.e. of the order of several thousand Pascal. Ultrasonic cleaning applications span a wide range from semiconductor manufacturing, to low pressure membrane cleaning, and the in the medical field cleaning of surgical instruments. We have developed a novel sensor to monitor and quantify cleaning activity which is (1) very sturdy, (2) has a high bandwidth of several megahertz, (3) is cheap in manufacturing costs, and (4) of very small size. We analyze the sensor signal by comparing its response time correlated to single laser induced cavitation bubbles using high-speed photography. Additionally, we will present first measurements in ultrasonic cleaning bathes using again high-speed photography. A preliminary discussion on the working mechanism of the sensor will be presented.

  9. THE IMPROVEMENT OF COMPUTER NETWORK PERFORMANCE WITH BANDWIDTH MANAGEMENT IN KEMURNIAN II SENIOR HIGH SCHOOL

    Directory of Open Access Journals (Sweden)

    Bayu Kanigoro

    2012-05-01

    Full Text Available This research describes the improvement of computer network performance with bandwidth management in Kemurnian II Senior High School. The main issue of this research is the absence of bandwidth division on computer, which makes user who is downloading data, the provided bandwidth will be absorbed by the user. It leads other users do not get the bandwidth. Besides that, it has been done IP address division on each room, such as computer, teacher and administration room for supporting learning process in Kemurnian II Senior High School, so wireless network is needed. The method is location observation and interview with related parties in Kemurnian II Senior High School, the network analysis has run and designed a new topology network including the wireless network along with its configuration and separation bandwidth on microtic router and its limitation. The result is network traffic on Kemurnian II Senior High School can be shared evenly to each user; IX and IIX traffic are separated, which improve the speed on network access at school and the implementation of wireless network.Keywords: Bandwidth Management; Wireless Network

  10. Using the Sirocco File System for high-bandwidth checkpoints.

    Energy Technology Data Exchange (ETDEWEB)

    Klundt, Ruth Ann; Curry, Matthew L.; Ward, H. Lee

    2012-02-01

    The Sirocco File System, a file system for exascale under active development, is designed to allow the storage software to maximize quality of service through increased flexibility and local decision-making. By allowing the storage system to manage a range of storage targets that have varying speeds and capacities, the system can increase the speed and surety of storage to the application. We instrument CTH to use a group of RAM-based Sirocco storage servers allocated within the job as a high-performance storage tier to accept checkpoints, allowing computation to potentially continue asynchronously of checkpoint migration to slower, more permanent storage. The result is a 10-60x speedup in constructing and moving checkpoint data from the compute nodes. This demonstration of early Sirocco functionality shows a significant benefit for a real I/O workload, checkpointing, in a real application, CTH. By running Sirocco storage servers within a job as RAM-only stores, CTH was able to store checkpoints 10-60x faster than storing to PanFS, allowing the job to continue computing sooner. While this prototype did not include automatic data migration, the checkpoint was available to be pushed or pulled to disk-based storage as needed after the compute nodes continued computing. Future developments include the ability to dynamically spawn Sirocco nodes to absorb checkpoints, expanding this mechanism to other fast tiers of storage like flash memory, and sharing of dynamic Sirocco nodes between multiple jobs as needed.

  11. High Speed and Wide Bandwidth Delta-Sigma ADCs

    NARCIS (Netherlands)

    Bolatkale, M.

    2013-01-01

    This thesis describes the theory, design and implementation of a high-speed, high-performance continuous-time delta-sigma (CTΔΣ) ADC for applications such as medical imaging, high-definition video processing, and wireline and wireless communications. In order to achieve a GHz clocking speed, this

  12. High Speed and Wide Bandwidth Delta-Sigma ADCs

    NARCIS (Netherlands)

    Bolatkale, M.

    2013-01-01

    This thesis describes the theory, design and implementation of a high-speed, high-performance continuous-time delta-sigma (CTΔΣ) ADC for applications such as medical imaging, high-definition video processing, and wireline and wireless communications. In order to achieve a GHz clocking speed, this th

  13. Extremelly High Bandwidth Rad Hard Data Acquisition System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Analog-to-digital converters (ADCs) are the key components for digitizing high-speed analog data in modern data acquisition systems, which is a critical part of...

  14. Extremelly High Bandwidth Rad Hard Data Acquisition System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Advancements in sensors/detectors are needed to support future NASA mission concepts including polarimetry, large format imaging arrays, and high-sensitivity...

  15. Plasma Sensor for High Bandwidth Mass-Flow Measurements at High Mach Numbers with RF Link Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposal is aimed at the development of a miniature high bandwidth (1 MHz class) plasma sensor for flow measurements at high enthalpies. This device uses a...

  16. High-Bandwidth Tactical-Network Data Analysis in a High-Performance-Computing (HPC) Environment: Device Status Data

    Science.gov (United States)

    2015-09-01

    5.1.1 Basic Components The Hydra data processing framework provides an object - oriented hierarchy for organizing data processing within an HPC...ARL-CR-0780 ● SEP 2015 US Army Research Laboratory High-Bandwidth Tactical-Network Data Analysis in a High-Performance-Computing...ARL-CR-0780 ● SEP 2015 US Army Research Laboratory High-Bandwidth Tactical-Network Data Analysis in a High-Performance-Computing (HPC

  17. Effective Actuation: High Bandwidth Actuators and Actuator Scaling Laws

    Science.gov (United States)

    2007-11-02

    piezo elements mounted on structural members and devices that exhibited aeroacoustic resonance. The former type of actuator ( piezo ) was considered...Raman and Kibens (Raman et al. 2000). These experiments involved high-frequency forcing applied to low-speed flows using wedge piezo actuators and... Subharmonic Interaction and Wall Influence," AIAA- 86-1047, May, 1986. Davis, S. A., 2000, "The manipulation of large and small flow structures in single and

  18. Fully Controllable Pancharatnam-Berry Metasurface Array with High Conversion Efficiency and Broad Bandwidth

    Science.gov (United States)

    Liu, Chuanbao; Bai, Yang; Zhao, Qian; Yang, Yihao; Chen, Hongsheng; Zhou, Ji; Qiao, Lijie

    2016-01-01

    Metasurfaces have powerful abilities to manipulate the properties of electromagnetic waves flexibly, especially the modulation of polarization state for both linearly polarized (LP) and circularly polarized (CP) waves. However, the transmission efficiency of cross-polarization conversion by a single-layer metasurface has a low theoretical upper limit of 25% and the bandwidth is usually narrow, which cannot be resolved by their simple additions. Here, we efficiently manipulate polarization coupling in multilayer metasurface to promote the transmission of cross-polarization by Fabry-Perot resonance, so that a high conversion coefficient of 80–90% of CP wave is achieved within a broad bandwidth in the metasurface with C-shaped scatters by theoretical calculation, numerical simulation and experiments. Further, fully controlling Pancharatnam-Berry phase enables to realize polarized beam splitter, which is demonstrated to produce abnormal transmission with high conversion efficiency and broad bandwidth. PMID:27703254

  19. Full phase stabilization of a Yb:fiber femtosecond frequency comb via high-bandwidth transducers

    NARCIS (Netherlands)

    Benko, C.; Ruehl, A.; Martin, M.J.; Eikema, K.S.E.; Fermann, M.E.; Hartl, I.; Ye, J.

    2012-01-01

    We present full phase stabilization of an amplified Yb:fiber femtosecond frequency comb using an intracavity electro-optic modulator and an acousto-optic modulator. These transducers provide high servo bandwidths of 580 kHz and 250 kHz for f(rep) and f(ceo), producing a robust and low phase noise fi

  20. High Bandwidth Rotary Fast Tool Servos and a Hybrid Rotary/Linear Electromagnetic Actuator

    Energy Technology Data Exchange (ETDEWEB)

    Montesanti, Richard Clement [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States)

    2005-09-01

    This thesis describes the development of two high bandwidth short-stroke rotary fast tool servos and the hybrid rotary/linear electromagnetic actuator developed for one of them. Design insights, trade-o® methodologies, and analytical tools are developed for precision mechanical systems, power and signal electronic systems, control systems, normal-stress electromagnetic actuators, and the dynamics of the combined systems.

  1. High-resolution and wide-bandwidth light intensity fiber optic displacement sensor for MEMS metrology.

    Science.gov (United States)

    Orłowska, Karolina; Świątkowski, Michał; Kunicki, Piotr; Kopiec, Daniel; Gotszalk, Teodor

    2016-08-01

    We report on the design, properties, and applications of a high-resolution and wide-bandwidth light intensity fiber optic displacement sensor for microelectromechanical system (MEMS) metrology. There are two types of structures that the system is dedicated to: vibrating with both high and low frequencies. In order to ensure high-frequency and high-resolution measurements, frequency down mixing and selective signal processing were applied. The obtained effective measuring bandwidth ranges from single hertz to 1 megahertz. The achieved resolution presented here is 116  pm/Hz1/2 and 138  pm/Hz1/2 for low-frequency and high-frequency operation modes, respectively, whereas the measurement of static displacement is 100 μm.

  2. Pickup design for high bandwidth bunch arrival-time monitors in free-electron lasers

    Energy Technology Data Exchange (ETDEWEB)

    Angelovski, Aleksandar; Penirschke, Andreas; Jakoby, Rolf [TU Darmstadt (Germany). Institut fuer Mikrowellentechnik und Photonik; Kuhl, Alexander; Schnepp, Sascha [TU Darmstadt (Germany). Graduate School of Computational Engineering; Bock, Marie Kristin; Bousonville, Michael; Schlarb, Holger [Deutsches Elektronen-Synchrotron DESY, Hamburg (Germany); Weiland, Thomas [TU Darmstadt (Germany). Institut fuer Theorie Elektromagnetischer Felder

    2012-07-01

    The increased demands for low bunch charge operation mode in the free-electron lasers (FELs) require an upgrade of the existing synchronization equipment. As a part of the laser-based synchronization system, the bunch arrival-time monitors (BAMs) should have a sub-10 femtosecond precision for high and low bunch charge operation. In order to fulfill the resolution demands for both modes of operation, the bandwidth of such a BAM should be increased up to a cutoff frequency of 40 GHz. In this talk, we present the design and the realization of high bandwidth cone-shaped pickup electrodes as a part of the BAM for the FEL in Hamburg (FLASH) and the European X-ray free-electron laser (European XFEL). The proposed pickup was simulated with CST STUDIO SUITE, and a non-hermetic model was built up for radio frequency (rf) measurements.

  3. Bullet: high bandwidth data dissemination using an overlay mesh

    OpenAIRE

    Kostic, D.; Rodriguez, A.; J. Albrecht; Vahdat, A.

    2003-01-01

    In recent years, overlay networks have become an effective alternative to IP multicast for efficient point to multipoint communication across the Internet. Typically, nodes self-organize with the goal of forming an efficient overlay tree, one that meets performance targets without placing undue burden on the underlying network. In this paper, we target high-bandwidth data distribution from a single source to a large number of receivers. Applications include large-file transfers and real-time ...

  4. Automatic high-bandwidth calibration and reconstruction of arbitrarily sampled parallel MRI.

    Directory of Open Access Journals (Sweden)

    Jan Aelterman

    Full Text Available Today, many MRI reconstruction techniques exist for undersampled MRI data. Regularization-based techniques inspired by compressed sensing allow for the reconstruction of undersampled data that would lead to an ill-posed reconstruction problem. Parallel imaging enables the reconstruction of MRI images from undersampled multi-coil data that leads to a well-posed reconstruction problem. Autocalibrating pMRI techniques encompass pMRI techniques where no explicit knowledge of the coil sensivities is required. A first purpose of this paper is to derive a novel autocalibration approach for pMRI that allows for the estimation and use of smooth, but high-bandwidth coil profiles instead of a compactly supported kernel. These high-bandwidth models adhere more accurately to the physics of an antenna system. The second purpose of this paper is to demonstrate the feasibility of a parameter-free reconstruction algorithm that combines autocalibrating pMRI and compressed sensing. Therefore, we present several techniques for automatic parameter estimation in MRI reconstruction. Experiments show that a higher reconstruction accuracy can be had using high-bandwidth coil models and that the automatic parameter choices yield an acceptable result.

  5. High-Bandwidth Dynamic Full-Field Profilometry for Nano-Scale Characterization of MEMS

    Energy Technology Data Exchange (ETDEWEB)

    Chen, L-C [Graduate Institute of Automation Technology, National Taipei University of Technology, 1 Sec. 3 Chung-Hsiao East Rd., Taipei, 106, Taiwan (China); Huang, Y-T [Graduate Institute of Automation Technology, National Taipei University of Technology, 1 Sec. 3 Chung-Hsiao East Rd., Taipei, 106, Taiwan (China); Chang, P-B [Graduate Institute of Mechanical and Electrical Engineering, National Taipei University of Technology, 1 Sec. 3 Chung-Hsiao East Rd., Taipei, 106, Taiwan (China)

    2006-10-15

    The article describes an innovative optical interferometric methodology to delivery dynamic surface profilometry with a measurement bandwidth up to 10MHz or higher and a vertical resolution up to 1 nm. Previous work using stroboscopic microscopic interferometry for dynamic characterization of micro (opto)electromechanical systems (M(O)EMS) has been limited in measurement bandwidth mainly within a couple of MHz. For high resonant mode analysis, the stroboscopic light pulse is insufficiently short to capture the moving fringes from dynamic motion of the detected structure. In view of this need, a microscopic prototype based on white-light stroboscopic interferometry with an innovative light superposition strategy was developed to achieve dynamic full-field profilometry with a high measurement bandwidth up to 10MHz or higher. The system primarily consists of an optical microscope, on which a Mirau interferometric objective embedded with a piezoelectric vertical translator, a high-power LED light module with dual operation modes and light synchronizing electronics unit are integrated. A micro cantilever beam used in AFM was measured to verify the system capability in accurate characterisation of dynamic behaviours of the device. The full-field seventh-mode vibration at a vibratory frequency of 3.7MHz can be fully characterized and nano-scale vertical measurement resolution as well as tens micrometers of vertical measurement range can be performed.

  6. A HIGH BANDWIDTH BIPOLAR POWER SUPPLY FOR THE FAST CORRECTORS IN THE APS UPGRADE*

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Ju; Sprau, Gary

    2017-06-25

    The APS Upgrade of a multi-bend achromat (MBA) storage ring requires a fast bipolar power supply for the fast correction magnets. The key performance requirement of the power supply includes a small-signal bandwidth of 10 kHz for the output current. This requirement presents a challenge to the design because of the high inductance of the magnet load and a limited input DC voltage. A prototype DC/DC power supply utilizing a MOSFET H-bridge circuit with a 500 kHz PWM has been developed and tested successfully. The prototype achieved a 10-kHz bandwidth with less than 3-dB attenuation for a signal 0.5% of the maximum operating current of 15 amperes. This paper presents the design of the power circuit, the PWM method, the control loop, and the test results.

  7. High-speed 405-nm superluminescent diode (SLD) with 807-MHz modulation bandwidth

    KAUST Repository

    Shen, Chao

    2016-08-25

    III-nitride LEDs are fundamental components for visible-light communication (VLC). However, the modulation bandwidth is inherently limited by the relatively long carrier lifetime. In this letter, we present the 405 nm emitting superluminescent diode (SLD) with tilted facet design on semipolar GaN substrate, showing a broad emission of ∼9 nm at 20 mW optical power. Owing to the fast recombination (τ<0.35 ns) through the amplified spontaneous emission, the SLD exhibits a significantly large 3-dB bandwidth of 807 MHz. A data rate of 1.3 Gbps with a bit-error rate of 2.9 × 10 was obtained using on-off keying modulation scheme, suggesting the SLD being a high-speed transmitter for VLC applications.

  8. Maximizing the bandwidth of coherent, mid-IR supercontinuum using highly nonlinear aperiodic nanofibers

    Science.gov (United States)

    Baili, Amira; Cherif, Rim; Heidt, Alexander; Zghal, Mourad

    2014-05-01

    We describe in detail a new procedure of maximizing the bandwidth of mid-infrared (mid-IR) supercontinuum (SC) in highly nonlinear microstructured As2Se3 and tellurite aperiodic nanofibers. By introducing aperiodic rings of first and secondary air holes into the cross-sections of our microstructured fiber designs, we achieve flattened and all-normal dispersion profiles over much broader bandwidths than would be possible with simple periodic designs. These fiber designs are optimized for efficient, broadband, and coherent SC generation in the mid-IR spectral region. Numerical simulations show that these designs enable the generation of a SC spanning over 2290 nm extending from 1140 to 3430 nm in 8 cm length of tellurite nanofiber with input energy of E = 200 pJ and a SC bandwidth of over 4700 nm extending from 1795 to 6525 nm generated in only 8 mm-length of As2Se3-based nanofiber with input energy as low as E = 100 pJ. This work provides a new type of broadband mid-IR SC source with flat spectral shape as well as excellent coherence and temporal properties by using aperiodic nanofibers with all-normal dispersion suitable for applications in ultrafast science, metrology, coherent control, non-destructive testing, spectroscopy, and optical coherence tomography in the mid-IR region.

  9. A Synthetic Bandwidth Method for High-Resolution SAR Based on PGA in the Range Dimension

    Directory of Open Access Journals (Sweden)

    Jincheng Li

    2015-06-01

    Full Text Available The synthetic bandwidth technique is an effective method to achieve ultra-high range resolution in an SAR system. There are mainly two challenges in its implementation. The first one is the estimation and compensation of system errors, such as the timing deviation and the amplitude-phase error. Due to precision limitation of the radar instrument, construction of the sub-band signals becomes much more complicated with these errors. The second challenge lies in the combination method, that is how to fit the sub-band signals together into a much wider bandwidth. In this paper, a novel synthetic bandwidth approach is presented. It considers two main errors of the multi-sub-band SAR system and compensates them by a two-order PGA (phase gradient auto-focus-based method, named TRPGA. Furthermore, an improved cut-paste method is proposed to combine the signals in the frequency domain. It exploits the redundancy of errors and requires only a limited amount of data in the azimuth direction for error estimation. Moreover, the up-sampling operation can be avoided in the combination process. Imaging results based on both simulated and real data are presented to validate the proposed approach.

  10. ICE-Based Custom Full-Mesh Network for the CHIME High Bandwidth Radio Astronomy Correlator

    Science.gov (United States)

    Bandura, K.; Cliche, J. F.; Dobbs, M. A.; Gilbert, A. J.; Ittah, D.; Mena Parra, J.; Smecher, G.

    New generation radio interferometers encode signals from thousands of antenna feeds across large bandwidth. Channelizing and correlating this data requires networking capabilities that can handle unprecedented data rates with reasonable cost. The Canadian Hydrogen Intensity Mapping Experiment (CHIME) correlator processes 8-bits from N=2,048 digitizer inputs across 400MHz of bandwidth. Measured in N2× bandwidth, it is the largest radio correlator that is currently commissioning. Its digital back-end must exchange and reorganize the 6.6terabit/s produced by its 128 digitizing and channelizing nodes, and feed it to the 256 graphics processing unit (GPU) node spatial correlator in a way that each node obtains data from all digitizer inputs but across a small fraction of the bandwidth (i.e. ‘corner-turn’). In order to maximize performance and reliability of the corner-turn system while minimizing cost, a custom networking solution has been implemented. The system makes use of Field Programmable Gate Array (FPGA) transceivers to implement direct, passive copper, full-mesh, high speed serial connections between sixteen circuit boards in a crate, to exchange data between crates, and to offload the data to a cluster of 256 GPU nodes using standard 10Gbit/s Ethernet links. The GPU nodes complete the corner-turn by combining data from all crates and then computing visibilities. Eye diagrams and frame error counters confirm error-free operation of the corner-turn network in both the currently operating CHIME Pathfinder telescope (a prototype for the full CHIME telescope) and a representative fraction of the full CHIME hardware providing an end-to-end system validation. An analysis of an equivalent corner-turn system built with Ethernet switches instead of custom passive data links is provided.

  11. Wide-Bandwidth, Wide-Beamwidth, High-Resolution, Millimeter-Wave Imaging for Concealed Weapon Detection

    Energy Technology Data Exchange (ETDEWEB)

    Sheen, David M.; Fernandes, Justin L.; Tedeschi, Jonathan R.; McMakin, Douglas L.; Jones, Anthony M.; Lechelt, Wayne M.; Severtsen, Ronald H.

    2013-06-12

    Active millimeter-wave imaging is currently being used for personnel screening at airports and other high-security facilities. The lateral resolution, depth resolution, clothing penetration, and image illumination quality obtained from next-generation systems can be significantly enhanced through the selection the aperture size, antenna beamwidth, center frequency, and bandwidth. In this paper, the results of an extensive imaging trade study are presented using both planar and cylindrical three-dimensional imaging techniques at frequency ranges of 10-20 GHz, 10 – 40 GHz, 40 – 60 GHz, and 75 – 105 GHz

  12. Applied Techniques for High Bandwidth Data Transfers across Wide Area Networks

    Institute of Scientific and Technical Information of China (English)

    JasonLee; BillAllcock; 等

    2001-01-01

    Large distributed systems such as Computational/Data Grids require large amounts of data to be co-located with the computing facilities for processing.From our work develogpin a scalable distributed network cache.we have gained experience with techniques necessary to achieve high data throughput over high bandwidth Wide Area Networks(WAN).In this paper,we discuss several hardware and software dsign techniques,and then describe their application to an implementation of an enhanced FTP protocol called GridFTP,We describe results from the Supercomputing 2000 conference.

  13. Designing and implementing Multibeam Smart Antennas for high bandwidth UAV communications using FPGAs

    Science.gov (United States)

    Porcello, J. C.

    Requirements for high bandwidth UAV communications are often necessary in order to move large amounts of mission information to/from Users in real-time. The focus of this paper is antenna beamforming for point-to-point, high bandwidth UAV communications in order to optimize transmit and receive power and support high data throughput communications. Specifically, this paper looks at the design and implementation of Multibeam Smart Antennas to implement antenna beamforming in an aerospace communications environment. The Smart Antenna is contrasted against Fast Fourier Transform (FFT) based beamforming in order to quantify the increase in both computational load and FPGA resources required for multibeam adaptive signal processing in the Smart Antenna. The paper begins with an overall discussion of Smart Antenna design and general beamforming issues in high bandwidth communications. Important design considerations such as processing complexity in a constrained Size, Weight and Power (SWaP) environment are discussed. The focus of the paper is with respect to design and implementation of digital beamforming wideband communications waveforms using FPGAs. A Multibeam Time Delay element is introduced based on Lagrange Interpolation. Design data for Multibeam Smart Antennas in FPGAs is provided in the paper as well as reference circuits for implementation. Finally, an example Multibeam Smart Antenna design is provided based on a Xilinx Virtex-7 FPGA. The Multibeam Smart Antenna example design illustrates the concepts discussed in the paper and provides design insight into Multibeam Smart Antenna implementation from the point of view of implementation complexity, required hardware, and overall system performance gain.

  14. Re-use of Low Bandwidth Equipment for High Bit Rate Transmission Using Signal Slicing Technique

    DEFF Research Database (Denmark)

    Wagner, Christoph; Spolitis, S.; Vegas Olmos, Juan José;

    : Massive fiber-to-the-home network deployment requires never ending equipment upgrades operating at higher bandwidth. We show effective signal slicing method, which can reuse low bandwidth opto-electronical components for optical communications at higher bit rates.......: Massive fiber-to-the-home network deployment requires never ending equipment upgrades operating at higher bandwidth. We show effective signal slicing method, which can reuse low bandwidth opto-electronical components for optical communications at higher bit rates....

  15. Influence of the fiber Bragg gratings with different reflective bandwidths in high power all-fiber laser oscillator

    Science.gov (United States)

    Wang, Jianming; Yan, Dapeng; Xiong, Songsong; Huang, Bao; Li, Cheng

    2017-01-01

    The effects of large-mode-area (LMA) fiber Bragg gratings (FBGs) with different reflective bandwidths on bi-directionally pumped ytterbium-doped single-mode all-fiber laser oscillator have been investigated experimentally. The forward laser output power and the backward signal leakage were measured and analyzed. It was found that the laser output power and efficiency depended on the bandwidth of the high-reflection (HR) FBG used in the laser cavity. The broader bandwidth gives higher laser efficiency, especially at high power level.

  16. Narrow-bandwidth high-order harmonics driven by long-duration hot spots

    Science.gov (United States)

    Kozlov, Maxim; Kfir, Ofer; Fleischer, Avner; Kaplan, Alex; Carmon, Tal; Schwefel, Harald G. L.; Bartal, Guy; Cohen, Oren

    2012-06-01

    We predict and investigate the emission of high-order harmonics by atoms that cross intense laser hot spots that last for a nanosecond or longer. An atom that moves through a nanometer-scale hot spot at characteristic thermal velocity can emit high-order harmonics in a similar fashion to an atom that is irradiated by a short-duration (picosecond-scale) laser pulse. We analyze the collective emission from a thermal gas and from a jet of atoms. In both cases, the line shape of a high-order harmonic exhibits a narrow spike with spectral width that is determined by the bandwidth of the driving laser. Finally, we discuss a scheme for producing long-duration laser hot spots with intensity in the range of the intensity threshold for high-harmonic generation. In the proposed scheme, the hot spot is produced by a long laser pulse that is consecutively coupled to a high-quality micro-resonator and a metallic nano-antenna. This system may be used for generating ultra-narrow bandwidth extreme-ultraviolet radiation through frequency up-conversion of a low-cost compact pump laser.

  17. Three-Axis Attitude Estimation With a High-Bandwidth Angular Rate Sensor

    Science.gov (United States)

    Bayard, David S.; Green, Joseph J.

    2013-01-01

    A continuing challenge for modern instrument pointing control systems is to meet the increasingly stringent pointing performance requirements imposed by emerging advanced scientific, defense, and civilian payloads. Instruments such as adaptive optics telescopes, space interferometers, and optical communications make unprecedented demands on precision pointing capabilities. A cost-effective method was developed for increasing the pointing performance for this class of NASA applications. The solution was to develop an attitude estimator that fuses star tracker and gyro measurements with a high-bandwidth angular rotation sensor (ARS). An ARS is a rate sensor whose bandwidth extends well beyond that of the gyro, typically up to 1,000 Hz or higher. The most promising ARS sensor technology is based on a magnetohydrodynamic concept, and has recently become available commercially. The key idea is that the sensor fusion of the star tracker, gyro, and ARS provides a high-bandwidth attitude estimate suitable for supporting pointing control with a fast-steering mirror or other type of tip/tilt correction for increased performance. The ARS is relatively inexpensive and can be bolted directly next to the gyro and star tracker on the spacecraft bus. The high-bandwidth attitude estimator fuses an ARS sensor with a standard three-axis suite comprised of a gyro and star tracker. The estimation architecture is based on a dual-complementary filter (DCF) structure. The DCF takes a frequency- weighted combination of the sensors such that each sensor is most heavily weighted in a frequency region where it has the lowest noise. An important property of the DCF is that it avoids the need to model disturbance torques in the filter mechanization. This is important because the disturbance torques are generally not known in applications. This property represents an advantage over the prior art because it overcomes a weakness of the Kalman filter that arises when fusing more than one rate

  18. APEnet+: high bandwidth 3D torus direct network for petaflops scale commodity clusters

    Science.gov (United States)

    Ammendola, R.; Biagioni, A.; Frezza, O.; Lo Cicero, F.; Lonardo, A.; Paolucci, P. S.; Rossetti, D.; Salamon, A.; Salina, G.; Simula, F.; Tosoratto, L.; Vicini, P.

    2011-12-01

    We describe herein the APElink+ board, a PCIe interconnect adapter featuring the latest advances in wire speed and interface technology plus hardware support for a RDMA programming model and experimental acceleration of GPU networking; this design allows us to build a low latency, high bandwidth PC cluster, the APEnet+ network, the new generation of our cost-effective, tens-of-thousands-scalable cluster network architecture. Some test results and characterization of data transmission of a complete testbench, based on a commercial development card mounting an Altera® FPGA, are provided.

  19. APEnet+: high bandwidth 3D torus direct network for petaflops scale commodity clusters

    CERN Document Server

    Ammendola, Roberto; Frezza, Ottorino; Cicero, Francesca Lo; Lonardo, Alessandro; Paolucci, Pier Stanislao; Rossetti, Davide; Salamon, Andrea; Salina, Gaetano; Simula, Francesco; Tosoratto, Laura; Vicini, Piero

    2011-01-01

    We describe herein the APElink+ board, a PCIe interconnect adapter featuring the latest advances in wire speed and interface technology plus hardware support for a RDMA programming model and experimental acceleration of GPU networking; this design allows us to build a low latency, high bandwidth PC cluster, the APEnet+ network, the new generation of our cost-effective, tens-of-thousands-scalable cluster network architecture. Some test results and characterization of data transmission of a complete testbench, based on a commercial development card mounting an Altera FPGA, are provided.

  20. Engineering the CernVM-Filesystem as a High Bandwidth Distributed Filesystem for Auxiliary Physics Data

    Science.gov (United States)

    Dykstra, D.; Bockelman, B.; Blomer, J.; Herner, K.; Levshina, T.; Slyz, M.

    2015-12-01

    A common use pattern in the computing models of particle physics experiments is running many distributed applications that read from a shared set of data files. We refer to this data is auxiliary data, to distinguish it from (a) event data from the detector (which tends to be different for every job), and (b) conditions data about the detector (which tends to be the same for each job in a batch of jobs). Relatively speaking, conditions data also tends to be relatively small per job where both event data and auxiliary data are larger per job. Unlike event data, auxiliary data comes from a limited working set of shared files. Since there is spatial locality of the auxiliary data access, the use case appears to be identical to that of the CernVM- Filesystem (CVMFS). However, we show that distributing auxiliary data through CVMFS causes the existing CVMFS infrastructure to perform poorly. We utilize a CVMFS client feature called "alien cache" to cache data on existing local high-bandwidth data servers that were engineered for storing event data. This cache is shared between the worker nodes at a site and replaces caching CVMFS files on both the worker node local disks and on the site's local squids. We have tested this alien cache with the dCache NFSv4.1 interface, Lustre, and the Hadoop Distributed File System (HDFS) FUSE interface, and measured performance. In addition, we use high-bandwidth data servers at central sites to perform the CVMFS Stratum 1 function instead of the low-bandwidth web servers deployed for the CVMFS software distribution function. We have tested this using the dCache HTTP interface. As a result, we have a design for an end-to-end high-bandwidth distributed caching read-only filesystem, using existing client software already widely deployed to grid worker nodes and existing file servers already widely installed at grid sites. Files are published in a central place and are soon available on demand throughout the grid and cached locally on the

  1. Engineering the CernVM-Filesystem as a High Bandwidth Distributed Filesystem for Auxiliary Physics Data

    Energy Technology Data Exchange (ETDEWEB)

    Dykstra, D. [Fermilab; Bockelman, B. [Nebraska U.; Blomer, J. [CERN; Herner, K. [Fermilab; Levshina, T. [Fermilab; Slyz, M. [Fermilab

    2015-12-23

    A common use pattern in the computing models of particle physics experiments is running many distributed applications that read from a shared set of data files. We refer to this data is auxiliary data, to distinguish it from (a) event data from the detector (which tends to be different for every job), and (b) conditions data about the detector (which tends to be the same for each job in a batch of jobs). Relatively speaking, conditions data also tends to be relatively small per job where both event data and auxiliary data are larger per job. Unlike event data, auxiliary data comes from a limited working set of shared files. Since there is spatial locality of the auxiliary data access, the use case appears to be identical to that of the CernVM- Filesystem (CVMFS). However, we show that distributing auxiliary data through CVMFS causes the existing CVMFS infrastructure to perform poorly. We utilize a CVMFS client feature called 'alien cache' to cache data on existing local high-bandwidth data servers that were engineered for storing event data. This cache is shared between the worker nodes at a site and replaces caching CVMFS files on both the worker node local disks and on the site's local squids. We have tested this alien cache with the dCache NFSv4.1 interface, Lustre, and the Hadoop Distributed File System (HDFS) FUSE interface, and measured performance. In addition, we use high-bandwidth data servers at central sites to perform the CVMFS Stratum 1 function instead of the low-bandwidth web servers deployed for the CVMFS software distribution function. We have tested this using the dCache HTTP interface. As a result, we have a design for an end-to-end high-bandwidth distributed caching read-only filesystem, using existing client software already widely deployed to grid worker nodes and existing file servers already widely installed at grid sites. Files are published in a central place and are soon available on demand throughout the grid and cached

  2. Memory bandwidth efficient two-layer reduced-resolution decoding of high-definition video

    Science.gov (United States)

    Comer, Mary L.

    2000-12-01

    This paper addresses the problem of efficiently decoding high- definition (HD) video for display at a reduced resolution. The decoder presented in this paper is intended for applications that are constrained not only in memory size, but also in peak memory bandwidth. This is the case, for example, during decoding of a high-definition television (HDTV) channel for picture-in-picture (PIP) display, if the reduced resolution PIP-channel decoder is sharing memory with the full-resolution main-channel decoder. The most significant source of video quality degradation in a reduced-resolution decoder is prediction drift, which is caused by the mismatch between the full-resolution reference frames used by the encoder and the subsampled reference frames used by the decoder. to mitigate the visually annoying effects of prediction drift, the decoder described in this paper operates at two different resolutions -- a lower resolution for B pictures, which do not contribute to prediction drift and a higher resolution for I and P pictures. This means that the motion-compensation unit (MCU) essentially operates at the higher resolution, but the peak memory bandwidth is the same as that required to decode at the lower resolution. Storage of additional data, representing the higher resolution for I and P pictures, requires a relatively small amount of additional memory as compared to decoding at the lower resolution. Experimental results will demonstrate the improvement in video quality achieved by the addition of the higher-resolution data in forming predictions for P pictures.

  3. High-bandwidth squeezed light at 1550 nm from a compact monolithic PPKTP cavity

    CERN Document Server

    Ast, Stefan; Schnabel, Roman

    2013-01-01

    We report the generation of squeezed vacuum states of light at 1550 nm with a broadband quantum noise reduction of up to 4.8 dB ranging from 5 MHz to 1.2 GHz sideband frequency. We used a custom-designed 2.6 mm long biconvex periodically-poled potassium titanyl phosphate (PPKTP) crystal. It featured reflectively coated end surfaces, 2.26 GHz of linewidth and generated the squeezing via optical parametric amplification. Two homodyne detectors with different quantum efficiencies and bandwidths were used to characterize the non-classical noise suppression. We measured squeezing values of up to 4.8 dB from 5 to 100 MHz and up to 3 dB from 100 MHz to 1.2 GHz. The squeezed vacuum measurements were limited by detection loss. We propose an improved detection scheme to measure up to 10 dB squeezing over 1 GHz. Our results of GHz bandwidth squeezed light generation provide new prospects for high-speed quantum key distribution.

  4. Mahanaxar: quality of service guarantees in high-bandwidth, real-time streaming data storage

    Energy Technology Data Exchange (ETDEWEB)

    Bigelow, David [Los Alamos National Laboratory; Bent, John [Los Alamos National Laboratory; Chen, Hsing-Bung [Los Alamos National Laboratory; Brandt, Scott [UCSC

    2010-04-05

    Large radio telescopes, cyber-security systems monitoring real-time network traffic, and others have specialized data storage needs: guaranteed capture of an ultra-high-bandwidth data stream, retention of the data long enough to determine what is 'interesting,' retention of interesting data indefinitely, and concurrent read/write access to determine what data is interesting, without interrupting the ongoing capture of incoming data. Mahanaxar addresses this problem. Mahanaxar guarantees streaming real-time data capture at (nearly) the full rate of the raw device, allows concurrent read and write access to the device on a best-effort basis without interrupting the data capture, and retains data as long as possible given the available storage. It has built in mechanisms for reliability and indexing, can scale to meet arbitrary bandwidth requirements, and handles both small and large data elements equally well. Results from our prototype implementation shows that Mahanaxar provides both better guarantees and better performance than traditional file systems.

  5. High Bandwidth Pickup Design for Bunch Arrival-time Monitors for Free-Electron Laser

    CERN Document Server

    Angelovski, Aleksandar; Hansli, Matthias; Penirschke, Andreas; Schnepp, Sascha M; Bousonville, Michael; Schlarb, Holger; Bock, Marie Kristin; Weiland, Thomas; Jakoby, Rolf

    2012-01-01

    In this paper, we present the design and realization of high bandwidth pickup electrodes with a cutoff frequency above 40 GHz. The proposed cone-shaped pickups are part of a bunch arrival-time monitor (BAM) designed for high (> 500 pC) and low (20 pC) bunch charge operation mode providing for a time resolution of less than 10 fs for both operation modes. The proposed design has a fast voltage response, low ringing, and a resonance-free spectrum. For assessing the influence of manufacturing tolerances on the performance of the pickups, an extensive tolerance study has been performed via numerical simulations. A non-hermetic model of the pickups was built for measurement and validation purposes. The measurement and simulation results are in good agreement and demonstrate the capability of the proposed pickup system to meet the given specifications.

  6. High bandwidth pickup design for bunch arrival-time monitors for free-electron laser

    Directory of Open Access Journals (Sweden)

    Aleksandar Angelovski

    2012-11-01

    Full Text Available In this paper, we present the design and realization of high bandwidth pickup electrodes with a cutoff frequency above 40 GHz. The proposed cone-shaped pickups are part of a bunch arrival-time monitor designed for high (>500  pC and low (20 pC bunch charge operation mode providing for a time resolution of less than 10 fs for both operation modes. The proposed design has a fast voltage response, low ringing, and a resonance-free spectrum. For assessing the influence of manufacturing tolerances on the performance of the pickups, an extensive tolerance study has been performed via numerical simulations. A nonhermetic model of the pickups was built for measurement and validation purposes. The measurement and simulation results are in good agreement and demonstrate the capability of the proposed pickup system to meet the given specifications.

  7. On Bandwidth Efficient Modulation for High-Data-Rate Wireless LAN Systems

    Directory of Open Access Journals (Sweden)

    Stolpman Victor

    2002-01-01

    Full Text Available We address the problem of high-data-rate orthogonal frequency division multiplexed (OFDM systems under restrictive bandwidth constraints. Based on recent theoretic results, multiple-input multiple-output (MIMO configurations are best suited for this problem. In this paper, we examine several MIMO configurations suitable for high rate transmission. In all scenarios considered, perfect channel state information (CSI is assumed at the receiver. In constrast, availability of CSI at the transmitter is addressed separately. We show that powerful space-time codes can be developed by combining some simple well-known techniques. In fact, we show that for certain configurations, these space-time MIMO configurations are near optimum in terms of outage capacity as compared to previously published codes. Performance evaluation of these techniques is demonstrated within the IEEE 802.11a framework via Monte Carlo simulations.

  8. Applied techniques for high bandwidth data transfers across wide area networks

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Jason; Gunter, Dan; Tierney, Brian; Allcock, Bill; Bester, Joe; Bresnahan, John; Tuecke, Steve

    2001-04-30

    Large distributed systems such as Computational/Data Grids require large amounts of data to be co-located with the computing facilities for processing. Ensuring that the data is there in time for the computation in today's Internet is a massive problem. From our work developing a scalable distributed network cache, we have gained experience with techniques necessary to achieve high data throughput over high bandwidth Wide Area Networks (WAN). In this paper, we discuss several hardware and software design techniques and issues, and then describe their application to an implementation of an enhanced FTP protocol called GridFTP. We also describe results from two applications using these techniques, which were obtained at the Supercomputing 2000 conference.

  9. High-Bandwidth Photon-Counting Detectors with Enhanced Near-Infrared Response Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Long-range optical telecommunications (LROT) impose challenging requirements on detector array sensitivity at 1064nm and arrays timing bandwidth. Large photonic...

  10. High bandwidth all-optical 3×3 switch based on multimode interference structures

    Science.gov (United States)

    Le, Duy-Tien; Truong, Cao-Dung; Le, Trung-Thanh

    2017-03-01

    A high bandwidth all-optical 3×3 switch based on general interference multimode interference (GI-MMI) structure is proposed in this study. Two 3×3 multimode interference couplers are cascaded to realize an all-optical switch operating at both wavelengths of 1550 nm and 1310 nm. Two nonlinear directional couplers at two outer-arms of the structure are used as all-optical phase shifters to achieve all switching states and to control the switching states. Analytical expressions for switching operation using the transfer matrix method are presented. The beam propagation method (BPM) is used to design and optimize the whole structure. The optimal design of the all-optical phase shifters and 3×3 MMI couplers are carried out to reduce the switching power and loss.

  11. Call Admission Control with Bandwidth Reallocation for Adaptive Multimedia in High-Rate Short-Range Wireless Networks

    Institute of Scientific and Technical Information of China (English)

    ZHAIXuping; BIGuangguo; XUPingping

    2005-01-01

    In high-rate short-range wireless networks,CAC (Call admission control) scheme plays an important role in quality of service provisioning for adaptive multimedia services. Three functions, namely bandwidth satisfaction function, revenue rate function and bandwidth reallocation cost function, are firstly introduced. Based on these functions, an efficient CAC scheme, the Rev-RT-BRA (Reservation-based and Revenue test with Bandwidth reallocation) CAC scheme is proposed. The main idea is that it reserves some bandwidth for service classes with higher admission priority. The performance of the Rev-RT-BRA CAC scheme is analyzed by solving a multidimension Markov process. Both the numerical and simulation results are given. The advantages of the proposedRev-RT-BRA CAC scheme are as follows. (1) It maximizes the overall bandwidth satisfaction function at any system state. (2) It solves the unfairness problem in admitting multiple classes of services with different bandwidth requirenlents. (3) The required admission priority level can be guaranteed for various classes of services.

  12. Tri-material multilayer coatings with high reflectivity and wide bandwidth for 25 to 50 nm extreme ultraviolet light

    Energy Technology Data Exchange (ETDEWEB)

    Aquila, Andrew; Salmassi, Farhad; Liu, Yanwei; Gullikson, Eric M.

    2009-09-09

    Magnesium/silicon carbide (Mg/SiC) multilayers have been fabricated with normal incidence reflectivity in the vicinity of 40% to 50% for wavelengths in the 25 to 50 nm wavelength range. However many applications, for example solar telescopes and ultrafast studies using high harmonic generation sources, desire larger bandwidths than provided by high reflectivity Mg/SiC multilayers. We investigate introducing a third material, Scandium, to create a tri-material Mg/Sc/SiC multilayer allowing an increase the bandwidth while maintaining high reflectivity.

  13. International distance education and the transition from ISDN to high-bandwidth Internet connectivity.

    Science.gov (United States)

    Vincent, Dale S; Berg, Benjamin W; Chitpatima, Suwicha; Hudson, Donald

    2002-12-01

    The Thailand Hawaii Assessment of Interactive Healthcare Initiative (THAI-HI) is an international distance-education project between two teaching hospitals in Honolulu and Bangkok that uses videoconferencing over three ISDN lines. A 'morning report' format is used to discuss clinical cases primarily covering infectious disease and critical-care topics. An audience response system is used at both sites to add interactivity. From July 2001 to May 2002, 816 health-care providers attended 20 clinical conferences. Audiences rated the conferences as highly relevant and as having high training value. Since the ISDN connection is expensive, we plan to convert the telecommunications to a high-bandwidth Internet connection. The Honolulu site will use a 45 Mbit/s commercial connection to the Hawaii Intranetwork Consortium, which links to the Abilene Network on the US mainland. The Bangkok hospital will use a 155 Mbit/s wireless optical connection to UNINET Thailand, which has a 45 Mbit/s circuit to Abilene.

  14. Radiation-tolerant, low-mass, high bandwidth, flexible printed circuit cables for particle physics experiments

    Science.gov (United States)

    McFadden, N. C.; Hoeferkamp, M. R.; Seidel, S.

    2016-09-01

    The design of meter long flexible printed circuit cables required for low-mass ultra-high speed signal transmission in the high radiation environment of the High Luminosity Large Hadron Collider is described. The design geometry is a differential embedded microstrip with 100 Ω nominal impedance. Minimal mass and maximal radiation hardness are pre-eminent considerations. Several dielectric materials are compared. To reduce mass, a cross hatched ground plane is applied. The long flexible printed circuit cables are characterized in bit error rate tests, attenuation versus frequency, mechanical response to temperature induced stress, and dimensional implications on radiation length. These tests are performed before and after irradiation with 1 MeV neutrons to 2×1016/cm2 and 800 MeV protons to 2×1016 1-MeV neutron equivalent/cm2. A 1.0 m Kapton cable with cross hatched ground plane, effective bandwidth of 4.976 gigabits per second, 0.0160% of a radiation length, and no detectable radiation-induced mechanical or electrical degradation is obtained.

  15. Radiation-tolerant, low-mass, high bandwidth, flexible printed circuit cables for particle physics experiments

    Energy Technology Data Exchange (ETDEWEB)

    McFadden, N.C.; Hoeferkamp, M.R.; Seidel, S.

    2016-09-11

    The design of meter long flexible printed circuit cables required for low-mass ultra-high speed signal transmission in the high radiation environment of the High Luminosity Large Hadron Collider is described. The design geometry is a differential embedded microstrip with 100 Ω nominal impedance. Minimal mass and maximal radiation hardness are pre-eminent considerations. Several dielectric materials are compared. To reduce mass, a cross hatched ground plane is applied. The long flexible printed circuit cables are characterized in bit error rate tests, attenuation versus frequency, mechanical response to temperature induced stress, and dimensional implications on radiation length. These tests are performed before and after irradiation with 1 MeV neutrons to 2×10{sup 16}/cm{sup 2} and 800 MeV protons to 2×10{sup 16} 1-MeV neutron equivalent/cm{sup 2}. A 1.0 m Kapton cable with cross hatched ground plane, effective bandwidth of 4.976 gigabits per second, 0.0160% of a radiation length, and no detectable radiation-induced mechanical or electrical degradation is obtained.

  16. Gbps wireless transceivers for high bandwidth interconnections in distributed cyber physical systems

    Science.gov (United States)

    Saponara, Sergio; Neri, Bruno

    2015-05-01

    In Cyber Physical Systems there is a growing use of high speed sensors like photo and video camera, radio and light detection and ranging (Radar/Lidar) sensors. Hence Cyber Physical Systems can benefit from the high communication data rate, several Gbps, that can be provided by mm-wave wireless transceivers. At such high frequency the wavelength is few mm and hence the whole transceiver including the antenna can be integrated in a single chip. To this aim this paper presents the design of 60 GHz transceiver architecture to ensure connection distances up to 10 m and data rate up to 4 Gbps. At 60 GHz there are more than 7 GHz of unlicensed bandwidth (available for free for development of new services). By using a CMOS SOI technology RF, analog and digital baseband circuitry can be integrated in the same chip minimizing noise coupling. Even the antenna is integrated on chip reducing cost and size vs. classic off-chip antenna solutions. Therefore the proposed transceiver can enable at physical layer the implementation of low cost nodes for a Cyber Physical System with data rates of several Gbps and with a communication distance suitable for home/office scenarios, or on-board vehicles such as cars, trains, ships, airplanes

  17. A 750MHz and a 8GHz High Bandwidth Digital FFT Spectrometer Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The scope of this project is to to develop a wide bandwidth, low power, and compact single board digital Fast Fourier Transform spectrometer (FFTS) optimized for the...

  18. High-Bandwidth Photon-Counting Detectors with Enhanced Near-Infrared Response Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Laser optical communications offer the potential to dramatically increase the link bandwidth and decrease the emitter power in long-range space communications....

  19. Design, analysis and testing of a parallel-kinematic high-bandwidth XY nanopositioning stage

    Energy Technology Data Exchange (ETDEWEB)

    Li, Chun-Xia; Gu, Guo-Ying; Yang, Mei-Ju; Zhu, Li-Min, E-mail: zhulm@sjtu.edu.cn [State Key Laboratory of Mechanical System and Vibration, School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China)

    2013-12-15

    This paper presents the design, analysis, and testing of a parallel-kinematic high-bandwidth XY nanopositioning stage driven by piezoelectric stack actuators. The stage is designed with two kinematic chains. In each kinematic chain, the end-effector of the stage is connected to the base by two symmetrically distributed flexure modules, respectively. Each flexure module comprises a fixed-fixed beam and a parallelogram flexure serving as two orthogonal prismatic joints. With the purpose to achieve high resonance frequencies of the stage, a novel center-thickened beam which has large stiffness is proposed to act as the fixed-fixed beam. The center-thickened beam also contributes to reducing cross-coupling and restricting parasitic motion. To decouple the motion in two axes totally, a symmetric configuration is adopted for the parallelogram flexures. Based on the analytical models established in static and dynamic analysis, the dimensions of the stage are optimized in order to maximize the first resonance frequency. Then finite element analysis is utilized to validate the design and a prototype of the stage is fabricated for performance tests. According to the results of static and dynamic tests, the resonance frequencies of the developed stage are over 13.6 kHz and the workspace is 11.2 μm × 11.6 μm with the cross-coupling between two axes less than 0.52%. It is clearly demonstrated that the developed stage has high resonance frequencies, a relatively large travel range, and nearly decoupled performance between two axes. For high-speed tracking performance tests, an inversion-based feedforward controller is implemented for the stage to compensate for the positioning errors caused by mechanical vibration. The experimental results show that good tracking performance at high speed is achieved, which validates the effectiveness of the developed stage.

  20. Controllable high bandwidth storage of optical information in a Bose-Einstein Condensate

    Science.gov (United States)

    Jayaseelan, Maitreyi; Schultz, Justin T.; Murphree, Joseph D.; Hansen, Azure; Bigelow, Nicholas P.

    2016-05-01

    The storage and retrieval of optical information has been of interest for a variety of applications including quantum information processing, quantum networks and quantum memories. Several schemes have been investigated and realized with weak, narrowband pulses, including techniques using EIT in solid state systems and both hot and cold atomic vapors. In contrast, we investigate the storage and manipulation of strong, high bandwidth pulses in a Bose-Einstein Condensate (BEC) of ultracold 87 Rb atoms. As a storage medium for optical pulses, BECs offer long storage times and preserve the coherence properties of the input information, suppressing unwanted thermal decoherence effects. We present numerical simulations of nanosecond pulses addressing a three-level lambda system on the D2 line of 87 Rb. The signal pulse is stored as a localized spin excitation in the condensate and can be moved or retrieved by reapplication of successive control pulses. The relative Rabi frequencies and areas of the pulses and the local atomic density in the condensate determine the storage location and readout of the signal pulse. Extending this scheme to use beams with a variety of spatial modes such as Hermite- and Laguerre-Gaussian modes offers an expanded alphabet for information storage.

  1. Wide bandwidth optical signals for high range resolution measurements in water

    Science.gov (United States)

    Nash, Justin; Lee, Robert; Mullen, Linda

    2016-05-01

    Measurements with high range resolution are needed to identify underwater threats, especially when two-dimensional contrast information is insufficient to extract object details. The challenge is that optical measurements are limited by scattering phenomena induced by the underwater channel. Back-scatter results in transmitted photons being directed back to the receiver before reaching the target of interest which induces a clutter signal for ranging and a reduction in contrast for imaging. Multiple small-angle scattering (forward-scatter) results in transmitted photons being directed to unintended regions of the target of interest (spatial spreading), while also stretching the temporal profile of a short optical pulse (temporal spreading). Spatial and temporal spreading of the optical signal combine to cause a reduction in range resolution in conventional laser imaging systems. NAVAIR has investigated ways in which wide bandwidth, modulated optical signals can be utilized to improve ranging and imaging performance in turbid water environments. Experimental efforts have been conducted to investigate channel effects on the propagated frequency content, as well as different filtering and processing techniques on the return signals to maximize range resolution. Of particular interest for the modulated pulses are coherent detection and processing techniques employed by the radar community, including methods to reduce sidelobe clutter. This paper will summarize NAVAIR's work and show that wideband optical signals, in combination with the CLEAN algorithm, can indeed provide enhancements to range resolution and 3D imagery in turbid water environments.

  2. Low latency, high bandwidth data communications between compute nodes in a parallel computer

    Science.gov (United States)

    Archer, Charles J.; Blocksome, Michael A.; Ratterman, Joseph D.; Smith, Brian E.

    2010-11-02

    Methods, parallel computers, and computer program products are disclosed for low latency, high bandwidth data communications between compute nodes in a parallel computer. Embodiments include receiving, by an origin direct memory access (`DMA`) engine of an origin compute node, data for transfer to a target compute node; sending, by the origin DMA engine of the origin compute node to a target DMA engine on the target compute node, a request to send (`RTS`) message; transferring, by the origin DMA engine, a predetermined portion of the data to the target compute node using memory FIFO operation; determining, by the origin DMA engine whether an acknowledgement of the RTS message has been received from the target DMA engine; if the an acknowledgement of the RTS message has not been received, transferring, by the origin DMA engine, another predetermined portion of the data to the target compute node using a memory FIFO operation; and if the acknowledgement of the RTS message has been received by the origin DMA engine, transferring, by the origin DMA engine, any remaining portion of the data to the target compute node using a direct put operation.

  3. A Lowpass Filter with Sharp Roll - off and High Relative Stopband Bandwidth Using Asymmetric High - Low Impedance Patches

    Directory of Open Access Journals (Sweden)

    As. Abdipour

    2015-09-01

    Full Text Available In this letter, a microstrip lowpass filter with -3 dB cut-off frequency at 1.286 GHz is proposed. By using two main resonators which are placed symmetrically around Y axis a sharp roll-off rate (250 dB/GHz is obtained. The proposed resonators are consisted of two asymmetric high-low impedance patches. To achieve a high relative stopband bandwidth (1.82 four high - low impedance resonators and four radial stubs as suppressing cells are employed. Furthermore, a flat insertion loss in the passband and a low return loss in the stopband can prove desired in-band and out-band frequency response. The proposed LPF has a high FOM about 63483.

  4. BASALT 1: Extravehicular Activity Science Operations Concepts under Communication Latency and Bandwidth Constraints at Craters of the Moon, Idaho

    Science.gov (United States)

    Chappell, Steven P.; Beaton, Kara; Miller, Matthew J.; Lim, Darlene S. S.; Abercromby, Andrew F. J.

    2017-01-01

    An over-arching goal of the multi-year Biologic Analog Science Associated with Lava Terrains (BASALT) project is to iteratively develop, implement, and evaluate concepts of operations (ConOps) and supporting capabilities intended to enable and enhance human exploration of Mars. Geological and biological scientific fieldwork is being conducted during four total deployments at two high-fidelity Mars analogs, all within simulated Mars mission conditions that are based on current architectural assumptions for Mars exploration missions. Specific capabilities being evaluated include the use of mobile science platforms, extravehicular informatics, communication and navigation packages, advanced science mission planning tools, and scientifically-relevant instrument packages to achieve the project goals. This paper describes the planning, execution, and results of the first field deployment, referred to as BASALT 1, which consisted of a series of 12 simulated extravehicular activities (EVAs) on the lava terrains of Craters of the Moon, Idaho. Scientific objectives of the EVAs related to determination of how microbial communities and habitability correlate with the physical and geochemical characteristics of chemically-altered basalt environments. The concept of operations (ConOps) and capabilities deployed and tested during BASALT 1 were based on extensive data from previous NASA trade studies and analog testing, and the primary research question was whether those ConOps and capabilities would work acceptably when performing real (non-simulated) biological and geological scientific exploration under four different communication scenarios. Specifically, communication latencies of 5 and 15 minutes one-way light time (OWLT) were tested; these delays fall within the range of 4 to 22 minute OWLT delays that would be experienced during a Mars mission. Science operations were also conducted under low bandwidth conditions (0.512 Mb/s uplink, 1.54 Mb/s downlink), representing a

  5. An InP-Based Dual-Depletion-Region Electroabsorption Modulator with Low Capacitance and Predicted High Bandwidth

    Institute of Scientific and Technical Information of China (English)

    SHAO Yong-Bo; ZHAO Ling-Juan; YU Hong-Yan; QIU Ji-Fang; QIU Ying-Ping; PAN Jiao-Qing; WANG Bao-Jun; ZHU Hong-Liang; WANG Wei

    2011-01-01

    A novel dual-depletion-region electroabsorption modulator (DDR-EAM) based on InP at 1550nm is fabricated.The measured capacitance and extinction ratio of the DDR-EAM reveal that the dual depletion region structure can reduce the device capacitance significantly without any degradation of extinction ratio.Moreover,the bandwidth of the DDR-EAM predicted by using an equivalent circuit model is larger than twice the bandwidth of the conventional lumped-electrode EAM (L-EAM).The electroabsorption modulator (EAM) is highly desirable as an external electro-optical modulator due to its high speed,low cost and capability of integration with other optical component such as DFB lasers,DBR lasers or semiconductor optical amplifiers.[1-4]So far,EAMs are typically fabricated by using lumped electrodes[1-4] and travelling-wave electrodes.[5-15]%A novel dual-depletion-region electroabsorption modulator (DDR-EAM) based on InP at 1550nm is fabricated. The measured capacitance and extinction ratio of the DDR-EAM reveal that the dual depletion region structure can reduce the device capacitance significantly without any degradation of extinction ratio. Moreover, the bandwidth of the DDR-EAM predicted by using an equivalent circuit model is larger than twice the bandwidth of the conventional lumped-electrode EAM (L-EAM).

  6. ICE-based Custom Full-Mesh Network for the CHIME High Bandwidth Radio Astronomy Correlator

    CERN Document Server

    Bandura, Kevin; Dobbs, Matt; Gilbert, Adam; Ittah, David; Parra, Juan Mena; Smecher, Graeme

    2016-01-01

    New generation radio interferometers encode signals from thousands of antenna feeds across large bandwidth. Channelizing and correlating this data requires networking capabilities that can handle unprecedented data rates with reasonable cost. The Canadian Hydrogen Intensity Mapping Experiment (CHIME) correlator processes 8-bits from N=2048 digitizer inputs across 400~MHz of bandwidth. Measured in $N^2~\\times $ bandwidth, it is the largest radio correlator that has been built. Its digital back-end must exchange and reorganize the 6.6~terabit/s produced by its 128 digitizing and channelizing nodes, and feed it to the 256-node spatial correlator in a way that each node obtains data from all digitizer inputs but across a small fraction of the bandwidth (i.e. `corner-turn'). In order to maximize performance and reliability of the corner-turn system while minimizing cost, a custom networking solution has been implemented. The system makes use of Field Programmable Gate Array (FPGA) transceivers to implement direct,...

  7. A high performance long-reach passive optical network with a novel excess bandwidth distribution scheme

    Science.gov (United States)

    Chao, I.-Fen; Zhang, Tsung-Min

    2015-06-01

    Long-reach passive optical networks (LR-PONs) have been considered to be promising solutions for future access networks. In this paper, we propose a distributed medium access control (MAC) scheme over an advantageous LR-PON network architecture that reroutes the control information from and back to all ONUs through an (N + 1) × (N + 1) star coupler (SC) deployed near the ONUs, thereby overwhelming the extremely long propagation delay problem in LR-PONs. In the network, the control slot is designed to contain all bandwidth requirements of all ONUs and is in-band time-division-multiplexed with a number of data slots within a cycle. In the proposed MAC scheme, a novel profit-weight-based dynamic bandwidth allocation (P-DBA) scheme is presented. The algorithm is designed to efficiently and fairly distribute the amount of excess bandwidth based on a profit value derived from the excess bandwidth usage of each ONU, which resolves the problems of previously reported DBA schemes that are either unfair or inefficient. The simulation results show that the proposed decentralized algorithms exhibit a nearly three-order-of-magnitude improvement in delay performance compared to the centralized algorithms over LR-PONs. Moreover, the newly proposed P-DBA scheme guarantees low delay performance and fairness even when under attack by the malevolent ONU irrespective of traffic loads and burstiness.

  8. High Speed Peltier Calorimeter for the Calibration of High Bandwidth Power Measurement Equipment

    CERN Document Server

    Frost, Damien F

    2015-01-01

    Accurate power measurements of electronic components operating at high frequencies are vital in determining where power losses occur in a system such as a power converter. Such power measurements must be carried out with equipment that can accurately measure real power at high frequency. We present the design of a high speed calorimeter to address this requirement, capable of reaching a steady state in less than 10 minutes. The system uses Peltier thermoelectric coolers to remove heat generated in a load resistance, and was calibrated against known real power measurements using an artificial neural network. A dead zone controller was used to achieve stable power measurements. The calibration was validated and shown to have an absolute accuracy of +/-8 mW (95% confidence interval) for measurements of real power from 0.1 to 5 W.

  9. Integrated high-speed DFB light source and narrow-bandwidth RCE photodetector for WDM fiber communication network application

    Science.gov (United States)

    Wang, Qiming; Li, Cheng; Pan, Zhong; Luo, Yi

    2000-10-01

    Electroabsorption (EA) modulator integrated with partially gain coupling distributed feedback (DFB) lasers have been fabricated and shown high single mode yield and wavelength stability. The small signal bandwidth is about 7.5 GHz. Strained Si1-xGex/Si multiple quantum well (MQW) resonant-cavity enhanced (RCE) photodetectors with SiO2/Si distributed Bragg reflector (DBR) as the mirrors have been fabricated and shown a clear narrow bandwidth response. The external quantum efficiency at 1.3 micrometer is measured to be about 3.5% under reverse bias of 16 V. A novel GaInNAs/GaAs MQW RCE p-i-n photodetector with high reflectance GaAs/AlAs DBR mirrors has also been demonstrated and shown the selectively detecting function with the FWHM of peak response of 12 nm.

  10. Silicon Photonics for All-Optical Processing and High-Bandwidth-Density Interconnects

    Science.gov (United States)

    Ophir, Noam

    The first chapter of the thesis provides motivation for the integration of silicon photonic modules into compute systems and surveys some of the recent developments in the field. The second chapter then proceeds to detail a technical case study of silicon photonic microring-based WDM links' scalability and power efficiency for these chip I/O applications which could be developed in the intermediate future. The analysis, initiated originally for a workshop on optical and electrical board and rack level interconnects, looks into a detailed model of the optical power budget for such a link capturing both single-channel aspects as well as WDM-operation-related considerations which are unique for a microring physical characteristics. The third chapter, while continuing on the theme silicon photonic high bandwidth density links, proceeds to detail the first experimental demonstration and characterization of an on-chip spatial division multiplexing (SDM) scheme based on microrings for the multiplexing and demultiplexing functionalities. In the context of more forward looking optical network-on-chip environments, SDM-enabled WDM photonic interconnects can potentially achieve superior bandwidth densities per waveguide compared to WDM-only photonic interconnects. The microring-based implementation allows dynamic tuning of the multiplexing and demultiplexing characteristic of the system which allows operation on WDM grid as well device tuning to combat intra-channel crosstalk. The characterization focuses on the first reported power penalty measurements for on-chip silicon photonic SDM link showing minimal penalties achievable with 3 spatial modes concurrently operating on a single waveguide with 10-Gb/s data carried by each mode. The fourth, fifth, and sixth chapters shift in topic from the application of silicon photonics to communication links to the evolving use of silicon waveguides for nonlinear all-optical processing. Chapter four primarily introduces and motivates

  11. Remote, Real-time Investigations of Extreme Environments Using High Power and Bandwidth Cabled Observatories: The OOI Regional Scale Nodes

    Science.gov (United States)

    Kelley, D. S.; Delaney, J. R.

    2012-12-01

    Methane hydrate deposits and hydrothermal vents are two of the most extreme environments on Earth. Seismic events and flow of gases from the seafloor support and modulate novel microbial communities within these systems. Although studied intensely for several decades, significant questions remain about the flux of heat, volatiles and microbial material from the subsurface to the hydrosphere in these dynamic environments. Quantification of microbial communities, their structure and abundances, and metabolic activities is in an infant state. To better understand these systems, the National Science Foundation's Ocean Observatory Initiative has installed high power (8 kW), high bandwidth (10 Gb/s) nodes on the seafloor that provide access to active methane seeps at Southern Hydrate Ridge, and at the most magmatically robust volcano on the Juan de Fuca Ridge - Axial Seamount. The real-time interactive capabilities of the cabled observatory are critical to studying gas-hydrate systems because many of the key processes occur over short time scales. Events such as bubble plume formation, the creation of collapse zones, and increased seepage in response to earthquakes require adaptive response and sampling capabilities. To meet these challenges a suite of instruments will be connected to the cable in 2013. These sensors include full resolution sampling by upward-looking sonars, fluid and gas chemical characterization by mass spectrometers and osmo samplers, long-term duration collection of seep imagery from cameras, and in situ manipulation of chemical sensors coupled with flow meters. In concert, this instrument suite will provide quantification of transient and more stable chemical fluxes. Similarly, at Axial Seamount the high bandwidth and high power fiber optic cables will be used to communicate with and power a diverse array of sensors at the summit of the volcano. Real-time high definition video will provide unprecedented views of macrofaunal and microbial communities

  12. A Low Power High Bandwidth Four Quadrant Analog Multiplier in 32 NM CNFET Technology

    Directory of Open Access Journals (Sweden)

    Vitrag Sheth

    2012-05-01

    Full Text Available Carbon Nanotube Field Effect Transistor (CNFET is a promising new technology that overcomes several limitations of traditional silicon integrated circuit technology. In recent years, the potential of CNFET for analog circuit applications has been explored. This paper proposes a novel four quadrant analog multiplier design using CNFETs. The simulation based on 32nm CNFET technology shows that the proposed multiplier has very low harmonic distortion (<0.45%, large input range (±400mV, large bandwidth (~50GHz and low power consumption (~247µW, while operating at a supply voltage of ±0.9V.

  13. Bandwidth and Noise in Spatiotemporally Modulated Mueller Matrix Polarimeters

    Science.gov (United States)

    Vaughn, Israel Jacob

    Polarimetric systems design has seen recent utilization of linear systems theory for system descriptions. Although noise optimal systems have been shown, bandwidth performance has not been addressed in depth generally and is particularly lacking for Mueller matrix (active) polarimetric systems. Bandwidth must be considered in a systematic way for remote sensing polarimetric systems design. The systematic approach facilitates both understanding of fundamental constraints and design of higher bandwidth polarimetric systems. Fundamental bandwidth constraints result in production of polarimetric "artifacts" due to channel crosstalk upon Mueller matrix reconstruction. This dissertation analyzes bandwidth trade-offs in spatio-temporal channeled Mueller matrix polarimetric systems. Bandwidth is directly related to the geometric positioning of channels in the Fourier (channel) space, however channel positioning for polarimetric systems is constrained both physically and by design parameters like domain separability. We present the physical channel constraints and the constraints imposed when the carriers are separable between space and time. Polarimetric systems are also constrained by noise performance, and there is a trade-off between noise performance and bandwidth. I develop cost functions which account for the trade-off between noise and bandwidth for spatio-temporal polarimetric systems. The cost functions allow a systems designer to jointly optimize systems with good bandwidth and noise performance. Optimization is implemented for a candidate spatio-temporal system design, and high temporal bandwidth systems resulting from the optimization are presented. Systematic errors which impact the bandwidth performance and mitigation strategies for these systematic errors are also presented. Finally, a portable imaging Mueller matrix system is built and analyzed based on the theoretical bandwidth analysis and system bandwidth optimization. Temporal bandwidth performance is

  14. Bandwidth-limited active suspension controller for an off-road vehicle based on co-simulation technology

    Institute of Scientific and Technical Information of China (English)

    Jinzhi FENG; Songlin ZHENG; Fan YU

    2008-01-01

    This paper presents the design process of a controller for bandwidth-limited active hydro-pneumatic suspension employed by an off-road vehicle based on co-simulation technology. First, a detailed multi-body dynamic model of the vehicle is established by using the ADAMS/View software package, which is followed by validation using a vehicle field test. Second, a combined PID and fuzzy controller is designed for the bandwidth-limited active suspension system and then programmed by means of S-functions in Matlab/Simulink, to which a data exchange interface with ADAMS/View is also defined. Third, the proposed control algorithm is implemented on the multi-body dynamic vehicle model to enable the co-simulation to run repeatedly until a more practical controller is achieved. In the end, the proposed active suspension system is compared with a conven-tional passive system. Simulation results show that the proposed active suspension system considerably improves both the ride and handling performance of the vehicle and therefore increases the maximum travel-ing speeds even on rough roads.

  15. A Broadband, Spectrally Flat, High Rep-rate Frequency Comb: Bandwidth Scaling and Flatness Enhancement of Phase Modulated CW through Cascaded Four-Wave Mixing

    CERN Document Server

    Supradeepa, V R

    2010-01-01

    We demonstrate a scheme to scale the bandwidth by several times while enhancing spectral flatness of frequency combs generated by intensity and phase modulation of CW lasers using cascaded four-wave mixing in highly nonlinear fiber.

  16. High-bandwidth Modulation of H2/Syngas Fuel to Control Combustion Dynamics in Micro-Mixing Lean Premix Systems

    Energy Technology Data Exchange (ETDEWEB)

    Jeff Melzak; Tim Lieuwen; Adel Mansour

    2012-01-31

    The goal of this program was to develop and demonstrate fuel injection technologies that will facilitate the development of cost-effective turbine engines for Integrated Gasification Combined Cycle (IGCC) power plants, while improving efficiency and reducing emissions. The program involved developing a next-generation multi-point injector with enhanced stability performance for lean premix turbine systems that burn hydrogen (H2) or synthesis gas (syngas) fuels. A previously developed injector that demonstrated superior emissions performance was improved to enhance static flame stability through zone staging and pilot sheltering. In addition, piezo valve technology was implemented to investigate the potential for enhanced dynamic stability through high-bandwidth modulation of the fuel supply. Prototype injector and valve hardware were tested in an atmospheric combustion facility. The program was successful in meeting its objectives. Specifically, the following was accomplished: Demonstrated improvement of lean operability of the Parker multi-point injector through staging of fuel flow and primary zone sheltering; Developed a piezo valve capable of proportional and high-bandwidth modulation of gaseous fuel flow at frequencies as high as 500 Hz; The valve was shown to be capable of effecting changes to flame dynamics, heat release, and acoustic signature of an atmospheric combustor. The latter achievement indicates the viability of the Parker piezo valve technology for use in future adaptively controlled systems for the mitigation of combustion instabilities, particularly for attenuating combustion dynamics under ultra-lean conditions.

  17. High-bandwidth multimode self-sensing in bimodal atomic force microscopy

    Directory of Open Access Journals (Sweden)

    Michael G. Ruppert

    2016-02-01

    Full Text Available Using standard microelectromechanical system (MEMS processes to coat a microcantilever with a piezoelectric layer results in a versatile transducer with inherent self-sensing capabilities. For applications in multifrequency atomic force microscopy (MF-AFM, we illustrate that a single piezoelectric layer can be simultaneously used for multimode excitation and detection of the cantilever deflection. This is achieved by a charge sensor with a bandwidth of 10 MHz and dual feedthrough cancellation to recover the resonant modes that are heavily buried in feedthrough originating from the piezoelectric capacitance. The setup enables the omission of the commonly used piezoelectric stack actuator and optical beam deflection sensor, alleviating limitations due to distorted frequency responses and instrumentation cost, respectively. The proposed method benefits from a more than two orders of magnitude increase in deflection to strain sensitivity on the fifth eigenmode leading to a remarkable signal-to-noise ratio. Experimental results using bimodal AFM imaging on a two component polymer sample validate that the self-sensing scheme can therefore be used to provide both the feedback signal, for topography imaging on the fundamental mode, and phase imaging on the higher eigenmode.

  18. Analysis and active compensation of microphonics in continuous wave narrow-bandwidth superconducting cavities

    Science.gov (United States)

    Neumann, A.; Anders, W.; Kugeler, O.; Knobloch, J.

    2010-08-01

    Many proposals for next generation light sources based on single pass free electron lasers or energy recovery linac facilities require a continuous wave (cw) driven superconducting linac. The effective beam loading in such machines is very small and in principle the cavities can be operated at a bandwidth of a few Hz and with less than a few kW of rf power. However, a power reserve is required to ensure field stability. A major error source is the mechanical microphonics detuning of the niobium cavities. To understand the influence of cavity detuning on longitudinal beam stability, a measurement program has been started at the horizontal cavity test facility HoBiCaT at HZB to study TESLA-type cavities. The microphonics detuning spectral content, peak detuning values, and the driving terms for these mechanical oscillations have been analyzed. In combination with the characterization of cw-adapted fast tuning systems based on the piezoelectric effect this information has been used to design a detuning compensation algorithm. It has been shown that a compensation factor between 2-7 is achievable, reducing the typical detuning of 2-3 Hz rms to below 0.5 Hz rms. These results were included in rf-control simulations of the cavities, and it was demonstrated that a phase stability below 0.02° can be achieved.

  19. Ultrawide bandwidth 1.55-um lasers

    Science.gov (United States)

    Morton, Paul A.; Tanbun-Ek, Tawee; Logan, Ralph A.; Ackerman, David A.; Shtengel, Gleb E.; Yadvish, R. D.; Sergent, A. M.; Sciortino, Paul F., Jr.

    1996-04-01

    This paper describes the essential elements for creating a practical wide bandwidth directly modulated laser source. This includes considerations of the intrinsic limitations of the laser structure, due to the resonant frequency and damping of the laser output, together with carrier transport issues to allow carriers in the device active region to be efficiently modulated at high speeds. the use of a P-doped compressively strained multiple-quantum well active region to provide high intrinsic speed and remove transport limitations is described, together with record setting results of 25 GHz modulation bandwidth for a 1.55 micrometer Fabry-Perot laser and 26 GHz bandwidth for a 1.55 micrometer DFB laser. The challenges of providing high bandwidth electrical connections to the laser on a suitable submount, together with fiber attachment and microwave packaging, are discussed. Results of fully packaged 1.55 micrometer DFB lasers with 25 Ghz modulation bandwidth are shown. Digital modulation of the packaged 1.55 micrometer DFB including impedance matching is described, and the transient wavelength chirp is presented. This low chirp is reduced further using an optical filter, to provide a 10 GBit/s source with chirp similar to that of an external electroabsorption modulator.

  20. High speed single-wavelength modulation and transmission at 2 μm under bandwidth-constrained condition.

    Science.gov (United States)

    Xu, Ke; Wu, Qiong; Xie, Yongqiang; Tang, Ming; Fu, Songnian; Liu, Deming

    2017-02-20

    The 2-μm optical band has gained much attention recently due to its potential applications in optical fiber communication systems. One constraint in this wavelength region is that the electrical bandwidth of components like modulators and photodetectors is limited by the immature manufacturing technologies. Here we experimentally demonstrated the high-speed signal generation and transmission under bandwidth-constrained scenario at 2-μm. It is enabled by the direct-detection optical filter bank multicarrier (FBMC) modulation technique with constant amplitude zero autocorrelation (CAZAC) equalization. We achieved a single wavelength 80 Gbit/s data rate using the 16-QAM FBMC modulation format which is the highest single channel bit rate at 2-μm according to our best knowledge. The signal is transmitted through a 100m-long solid-core fiber designed for single-mode transmission at 2-μm. The measured bit error rates of the signals are below the forward error correction limit of 3.8 × 10-3, and the 100m-fiber transmission brings negligible penalty.

  1. Low-bandwidth authentication.

    Energy Technology Data Exchange (ETDEWEB)

    Donnelly, Patrick Joseph; McIver, Lauren; Gaines, Brian R.; Anderson, Erik; Collins, Michael Joseph; Thomas,Kurt Adam; McDaniel, Austin

    2007-09-01

    Remotely-fielded unattended sensor networks generally must operate at very low power--in the milliwatt or microwatt range--and thus have extremely limited communications bandwidth. Such sensors might be asleep most of the time to conserve power, waking only occasionally to transmit a few bits. RFID tags for tracking or material control have similarly tight bandwidth constraints, and emerging nanotechnology devices will be even more limited. Since transmitted data is subject to spoofing, and since sensors might be located in uncontrolled environments vulnerable to physical tampering, the high-consequence data generated by such systems must be protected by cryptographically sound authentication mechanisms; but such mechanisms are often lacking in current sensor networks. One reason for this undesirable situation is that standard authentication methods become impractical or impossible when bandwidth is severely constrained; if messages are small, a standard digital signature or HMAC will be many times larger than the message itself, yet it might be possible to spare only a few extra bits per message for security. Furthermore, the authentication tags themselves are only one part of cryptographic overhead, as key management functions (distributing, changing, and revoking keys) consume still more bandwidth. To address this problem, we have developed algorithms that provide secure authentication while adding very little communication overhead. Such techniques will make it possible to add strong cryptographic guarantees of data integrity to a much wider range of systems.

  2. Low-bandwidth authentication.

    Energy Technology Data Exchange (ETDEWEB)

    Donnelly, Patrick Joseph; McIver, Lauren; Gaines, Brian R.; Anderson, Erik; Collins, Michael Joseph; Thomas,Kurt Adam; McDaniel, Austin

    2007-09-01

    Remotely-fielded unattended sensor networks generally must operate at very low power--in the milliwatt or microwatt range--and thus have extremely limited communications bandwidth. Such sensors might be asleep most of the time to conserve power, waking only occasionally to transmit a few bits. RFID tags for tracking or material control have similarly tight bandwidth constraints, and emerging nanotechnology devices will be even more limited. Since transmitted data is subject to spoofing, and since sensors might be located in uncontrolled environments vulnerable to physical tampering, the high-consequence data generated by such systems must be protected by cryptographically sound authentication mechanisms; but such mechanisms are often lacking in current sensor networks. One reason for this undesirable situation is that standard authentication methods become impractical or impossible when bandwidth is severely constrained; if messages are small, a standard digital signature or HMAC will be many times larger than the message itself, yet it might be possible to spare only a few extra bits per message for security. Furthermore, the authentication tags themselves are only one part of cryptographic overhead, as key management functions (distributing, changing, and revoking keys) consume still more bandwidth. To address this problem, we have developed algorithms that provide secure authentication while adding very little communication overhead. Such techniques will make it possible to add strong cryptographic guarantees of data integrity to a much wider range of systems.

  3. Comparison of State-of-the-Art Digital Control and Analogue Control for High Bandwidth Point of Load Converters

    DEFF Research Database (Denmark)

    Jakobsen, Lars Tønnes; Schneider, Henrik; Andersen, Michael Andreas E.

    2008-01-01

    The purpose of this paper is to present a comparison of state-of-the-art digital and analogue control for a Buck converter with synchronous rectification. The digital control scheme is based on a digital self-oscillating modulator that allows the sampling frequency to be higher than the switching...... frequency of the converter. Voltage mode control is used in both the analogue and digital control schemes. The experimental results show that it is possible to design a digitally controlled Buck converter that has the same performance as can be achieved using commercially available analogue control ICs....... The performance of the analogue system can however be increased by using a separate operational amplifier as error amplifier. Thus analogue control is still the best option if high control bandwidth and fast transient response to load steps are important design parameters....

  4. High-Bandwidth Atomic Force Microscopy Reveals A Mechanical spike Accompanying the Action Potential in mammalian Nerve Terminals

    Science.gov (United States)

    Salzberg, Brian M.

    2008-03-01

    Information transfer from neuron to neuron within nervous systems occurs when the action potential arrives at a nerve terminal and initiates the release of a chemical messenger (neurotransmitter). In the mammalian neurohypophysis (posterior pituitary), large and rapid changes in light scattering accompany secretion of transmitter-like neuropeptides. In the mouse, these intrinsic optical signals are intimately related to the arrival of the action potential (E-wave) and the release of arginine vasopressin and oxytocin (S-wave). We have used a high bandwidth (20 kHz) atomic force microscope (AFM) to demonstrate that these light scattering signals are associated with changes in nerve terminal volume, detected as nanometer-scale movements of a cantilever positioned on top of the neurohypophysis. The most rapid mechanical response, the ``spike'', has duration comparable to that of the action potential (˜2 ms) and probably reflects an increase in terminal volume due to H2O movement associated with Na^+-influx. Elementary calculations suggest that two H2O molecules accompanying each Na^+-ion could account for the ˜0.5-1.0 å increase in the diameter of each terminal during the action potential. Distinguishable from the mechanical ``spike'', a slower mechanical event, the ``dip'', represents a decrease in nerve terminal volume, depends upon Ca^2+-entry, as well as on intra-terminal Ca^2+-transients, and appears to monitor events associated with secretion. A simple hypothesis is that this ``dip'' reflects the extrusion of the dense core granule that comprises the secretory products. These dynamic high bandwidth AFM recordings are the first to monitor mechanical events in nervous systems and may provide novel insights into the mechanism(s) by which excitation is coupled to secretion at nerve terminals.

  5. Ultra-low Noise, High Bandwidth, 1550nm HgCdTe APD Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Voxtel Inc. proposes to optimize the design of a large area, 1.55?m sensitive HgCdTe avalanche photodiode (APD) that achieves high gain with nearly no excess noise....

  6. Electrothermal impedance spectroscopy measurement on high power LiMO2/Li4Ti5O12 battery cell with low bandwidth test setup

    DEFF Research Database (Denmark)

    Swierczynski, Maciej Jozef; Stroe, Daniel Loan; Stanciu, Tiberiu

    2015-01-01

    Modern lithium-ion batteries, like LiMO2/Li4Ti5O12 chemistry, are having very high power capability, which drives the need for precise thermal modelling of the battery. Battery thermal models are required to avoid possible safety issues (thermal runaways, high-temperature gradients) but also......-bandwidth and high-current capability for large format battery cells. Thus, this paper evaluates the possibility and accuracy of performing ETIS measurements with a standard battery test station (or bidirectional power supply) with low-bandwidth....

  7. Algorithms and Requirements for Measuring Network Bandwidth

    Energy Technology Data Exchange (ETDEWEB)

    Jin, Guojun

    2002-12-08

    This report unveils new algorithms for actively measuring (not estimating) available bandwidths with very low intrusion, computing cross traffic, thus estimating the physical bandwidth, provides mathematical proof that the algorithms are accurate, and addresses conditions, requirements, and limitations for new and existing algorithms for measuring network bandwidths. The paper also discusses a number of important terminologies and issues for network bandwidth measurement, and introduces a fundamental parameter -Maximum Burst Size that is critical for implementing algorithms based on multiple packets.

  8. Development of Advanced Low Emission Injectors and High-Bandwidth Fuel Flow Modulation Valves

    Science.gov (United States)

    Mansour, Adel

    2015-01-01

    Parker Hannifin Corporation developed the 3-Zone fuel nozzle for NASA's Environmentally Responsible Aviation Program to meet NASAs target of 75 LTO NOx reduction from CAEP6 regulation. The nozzle concept was envisioned as a drop-in replacement for currently used fuel nozzle stem, and is built up from laminates to provide energetic mixing suitable for lean direct injection mode at high combustor pressure. A high frequency fuel valve was also developed to provide fuel modulation for the pilot injector. Final testing result shows the LTO NOx level falling just shy of NASAs goal at 31.

  9. High Bandwidth Zero Voltage Injection Method for Sensorless Control of PMSM

    DEFF Research Database (Denmark)

    Ge, Xie; Lu, Kaiyuan; Kumar, Dwivedi Sanjeet

    2014-01-01

    High frequency signal injection is widely used in PMSM sensorless control system for low speed operations. The conventional voltage injection method often needs filters to obtain particular harmonic component in order to estimate the rotor position; or it requires several voltage pulses to be inj...... in a fast current regulation performance. Injection of zero voltage also minimizes the inverter voltage error effects caused by the dead-time.......High frequency signal injection is widely used in PMSM sensorless control system for low speed operations. The conventional voltage injection method often needs filters to obtain particular harmonic component in order to estimate the rotor position; or it requires several voltage pulses...... to be injected before the position may be estimated. In this paper, a single pulse zero voltage injection method is proposed. The rotor position is directly estimated from the current ripple at half of the switching frequency. No machine parameters are needed and using of filters is avoided. This results...

  10. Achieving High Resolution Measurements Within Limited Bandwidth Via Sensor Data Compression

    Science.gov (United States)

    2013-06-01

    are buffered separately and then saved when peaks are detected. The data are time stamped and inserted into a first-in, first-out ( FIFO ) buffer...16 samples around the peak are saved. These samples are combined with 2 solar sync words and 2 time stamp words, and are buffered into a FIFO for...Output Frame 5 A/D High Speed Fames Low Speed Fames Solar Buffer Peak Detect Time- Stamped Solar Pulse TX Buffer Solar FIFO

  11. High flux, narrow bandwidth compton light sources via extended laser-electron interactions

    Science.gov (United States)

    Barty, V P

    2015-01-13

    New configurations of lasers and electron beams efficiently and robustly produce high flux beams of bright, tunable, polarized quasi-monoenergetic x-rays and gamma-rays via laser-Compton scattering. Specifically, the use of long-duration, pulsed lasers and closely-spaced, low-charge and low emittance bunches of electron beams increase the spectral flux of the Compton-scattered x-rays and gamma rays, increase efficiency of the laser-electron interaction and significantly reduce the overall complexity of Compton based light sources.

  12. Wide bandwidth and high resolution planar filter array based on DBR-metasurface-DBR structures

    CERN Document Server

    Horie, Yu; Arbabi, Ehsan; Kamali, Seyedeh Mahsa; Faraon, Andrei

    2016-01-01

    We propose and experimentally demonstrate a planar array of optical bandpass filters composed of low loss dielectric metasurface layers sandwiched between two distributed Bragg reflectors (DBRs). The two DBRs form a Fabry-P\\'erot resonator whose center wavelength is controlled by the design of the transmissive metasurface layer which functions as a phase shifting element. We demonstrate an array of bandpass filters with spatially varying center wavelengths covering a wide range of operation wavelengths of 250 nm around {\\lambda} = 1550 nm ({\\Delta}{\\lambda}/{\\lambda} = 16%). The center wavelengths of each filter are independently controlled only by changing the in-plane geometry of the sandwiched metasurfaces, and the experimentally measured quality factors are larger than 700. The demonstrated filter array can be directly integrated on top of photodetector arrays to realize on-chip high-resolution spectrometers with free-space coupling.

  13. Development of Radiation-Tolerant, Low Mass, High Bandwidth Flexible Printed Circuit Cables for Particle Detection Applications

    Science.gov (United States)

    McFadden, Neil

    2016-03-01

    Design options for meter long flexible printed circuit cables required for low mass ultra-high speed signal transmission in the high radiation environment at the High Luminosity run of the Large Hadron Collider (LHC) are described. Two dielectric materials were considered in this study, Kapton and a Kapton/Teflon mixture. The design geometry is a differential embedded microstrip with nominal 100 Ω impedance. Minimal mass and maximal radiation hardness are pre-eminent considerations. The long flexible printed circuit cables are characterized in bit error rate tests (BERT), attenuation versus frequency, mechanical response to stress and temperature change, and RLC decomposition. These tests are performed before and after irradiation with 1 MeV neutrons to 2x1016/cm 2 and 800 MeV protons to 2x1016 1 MeV-neq/cm2. A 1.0 m Kapton cable, with bandwidth of 6.22 gigabits per second, 0.03% of a radiation length, and no radiation induced mechanical or electrical degradation is obtained.

  14. A Novel Multi-carrier Radar for High-speed Wide-bandwidth Stepped-Frequency GPR

    Science.gov (United States)

    Kyoo Kim, Dong; Choi, Young Woo; Kang, Do Wook

    2015-04-01

    Ground Penetrating Radar (GPR) is one of the non-destructive testing methods for studying underground situations by using the electro-magnetic wave radiation effect. Two classical sensing techniques, impulsive GPR and stepped-frequency GPR, are used for a long time in various GPR applications. Signal bandwidths generated by the two techniques ranges from several hundred MHz to several GHz. For the research area of pavement survey the surveying speed is emphasized, thus impulsive GPR has been preferred to stepped-frequency GPR. To make a complete single scan operation, stepped-frequency GPR needs over hundreds of different frequency continuous wave (CW) radiations within its signal bandwidth which is the main time taking process. In case of impulsive GPR, it needs also several repeated pulses, for example from 64 to 512 repeated pulses, to do a complete single scan operation. Although the two techniques need several repeated internal operation processes, impulsive GPR is generally considered to be fast than stepped-frequency GPR. On the other hand, many studies of stepped-frequency GPR emphasizes that high-resolution scanning accuracy can be achieved by controlling each frequency component differently, such as frequency power profile, flexible bandwidth control. In case of pavement survey area, high-accuracy scanning is required within one meter deep as well as high-speed survey. The required accuracy is up to several centimeter in the material where dielectric constant is about 10. When surveying pavement, multi-element array antenna gives advantages to the measurement accuracy enhancement, where the scanning region of a 3 meters wide paved road is divided into several sub-regions as the number of the antenna element. For example, when stepped-frequency GPR requires 6msec for single scan operation and 15-element antenna is considered, the survey speed is limited to 15km/h in order to scan the road every 5cm, which is slow compared with common driving condition on

  15. Level-1 Data Driver Card - A high bandwidth radiation tolerant aggregator board for detectors

    CERN Document Server

    Gkountoumis, Panagiotis; The ATLAS collaboration

    2017-01-01

    The Level-1 Data Driver Card (L1DDC) was designed for the needs of the future upgrades of the innermost stations of the ATLAS end-cap muon spectrometer. The L1DDC is a high speed aggregator board capable of communicating with multiple front-end electronic boards. It collects the Level-1 data along with monitoring data and transmits them to a network interface through bidirectional and/or unidirectional fiber links at 4.8 Gbps each. In addition, the L1DDC board distributes trigger, time and configuration data coming from the network interface to the front-end boards. The L1DDC is fully compatible with the Phase II upgrade where the trigger rate is expected to reach the 1 MHz. Three different types of L1DDC boards will be fabricated handling up to 10.080 Gbps of user data. It consist of custom made radiation tolerant ASICs: the GigaBit Transceiver (GBTx), the FEAST DC-DC converter, the Slow Control Adapter (SCA), and the Versatile Tranceivers (VTRX) and transmitters (VTTX). The overall scheme of the data acquis...

  16. High Bandwidth, Multi-Purpose Passive Radar Receiver Design For Aerospace and Geoscience Targets

    Science.gov (United States)

    Vertatschitsch, Laura

    uninterruptible power supply (UPS) for up to 1 hour of continuous operation. In this document we provide technical details of the hardware, firmware, and software of the system and design strategies and decisions. We cover the topic of coherent processing for passive radar, specifically an overview of the cross-ambiguity function as a detection mechanism. While the applications of a system like this are incredibly broad, the initial validation and performance analysis was applied specifically to detection of aircraft using Digital Television (DTV) broadcast as an illuminator. We present results of both stationary and mobile operation. In stationary operation, the same helicopter has been detected using two different DTV transmissions. Early mobile operation results show the Doppler-spread ground clutter and possible detection of aircraft. In addition to the fully-functional aircraft detection signal chain, alternative FPGA designs are presented with modes for fast sampling on two antennas or four antennas, with access to an aggregate 240 MHz of spectrum, with 8-bit samples. At these extremely high data rates, moderate data loss occurs while saving this data to disk, but as detailed within this document, it can be accounted for and the effects minimalized, still allowing for detection of aircraft. With these modes, FM transmission and DTV transmission can be captured synchronously from a single antenna and digitizer feed, an exciting result that offers promise for both aerospace and geoscience applications.

  17. Two-photon-excited fluorescence (TPEF) and fluorescence lifetime imaging (FLIM) with sub-nanosecond pulses and a high analog bandwidth signal detection

    Science.gov (United States)

    Eibl, Matthias; Karpf, Sebastian; Hakert, Hubertus; Weng, Daniel; Huber, Robert

    2017-02-01

    Two-photon excited fluorescence (TPEF) microscopy and fluorescence lifetime imaging (FLIM) are powerful imaging techniques in bio-molecular science. The need for elaborate light sources for TPEF and speed limitations for FLIM, however, hinder an even wider application. We present a way to overcome this limitations by combining a robust and inexpensive fiber laser for nonlinear excitation with a fast analog digitization method for rapid FLIM imaging. The applied sub nanosecond pulsed laser source is synchronized to a high analog bandwidth signal detection for single shot TPEF- and single shot FLIM imaging. The actively modulated pulses at 1064nm from the fiber laser are adjustable from 50ps to 5ns with kW of peak power. At a typically applied pulse lengths and repetition rates, the duty cycle is comparable to typically used femtosecond pulses and thus the peak power is also comparable at same cw-power. Hence, both types of excitation should yield the same number of fluorescence photons per time on average when used for TPEF imaging. However, in the 100ps configuration, a thousand times more fluorescence photons are generated per pulse. In this paper, we now show that the higher number of fluorescence photons per pulse combined with a high analog bandwidth detection makes it possible to not only use a single pulse per pixel for TPEF imaging but also to resolve the exponential time decay for FLIM. To evaluate the performance of our system, we acquired FLIM images of a Convallaria sample with pixel rates of 1 MHz where the lifetime information is directly measured with a fast real time digitizer. With the presented results, we show that longer pulses in the many-10ps to nanosecond regime can be readily applied for TPEF imaging and enable new imaging modalities like single pulse FLIM.

  18. Electro-optic prism-pair setup for efficient high bandwidth isochronous CEP phase shift or group delay generation

    Science.gov (United States)

    Gobert, Olivier; Mennerat, Gabriel; Cornaggia, Christian; Lupinski, Dominique; Perdrix, Michel; Guillaumet, Delphine; Lepetit, Fabien; Oksenhendler, Thomas; Comte, Michel

    2016-05-01

    We report the experimental demonstration of an electro-optic prism pair pure carrier-envelope phase (CEP) shifter at low voltage (shift of 1 rad for a voltage of 90 V, applied to a crystal of 5 mm aperture). Validating our mathematical model, the experiments prove that this set-up which uses two rubidium titanyl phosphate (RTP) crystals, can be used either as an efficient high bandwidth CEP shifter without modifying the group delay of an ultrashort pulse (isochronous CEP shifter) or alternatively as a group delay generator with quasi-constant CEP (Pure Group Delay generator). These two configurations which correspond to specific geometries are characterized by spectral interferometry with a 800 nm mode-locked Ti:sapphire laser. The results are in very good agreement with the model. In the pure group delay mode, a group delay of 2.3 fs is obtained at 1000 V/cm without significant CEP shift. In the isochronous mode, a shift of 5.5 rad at 1000 V/cm is generated without significant delay. The applied voltage is also lowered by a factor of nearly three in this configuration, compared to the case of an RTP rectangular slab of the same total length.

  19. Power spectrum analysis for optical tweezers. II: Laser wavelength dependence of parasitic filtering, and how to achieve high bandwidth

    DEFF Research Database (Denmark)

    Berg-Sørensen, Kirstine; Peterman, Erwin J G; Weber, Tom

    2006-01-01

    In a typical optical tweezers detection system, the position of a trapped object is determined from laser light impinging on a quadrant photodiode. When the laser is infrared and the photodiode is of silicon, they can act together as an unintended low-pass filter. This parasicit effect is due...... this detection system of optical tweezers a bandwidth, accuracy, and precision that are limited only by the data acquisition board's bandwidth and bandpass ripples, here 96.7 kHz and 0.005 dB, respectively. ©2006 American Institute of Physics...

  20. Weak-quasi-bandwidth and forward-bandwidth of graphs

    Institute of Scientific and Technical Information of China (English)

    原晋江

    1996-01-01

    Concepts of weak-quasi-bandwidth and forward-bandwidth of graphs are introduced. They are used to studythe following problems in graph theory: bandwidth, topological bandwidth, fill-in, profile, path-width, tree-width.

  1. Simulation and Analysis of Router Buffer Requirements in High Bandwidth-Delay Networks%高带宽延迟网络中路由器缓存需求的仿真分析

    Institute of Scientific and Technical Information of China (English)

    王建新; 李春泉; 黄家玮

    2009-01-01

    In order to meet the requirement for router buffer size in high bandwidth-delay networks, five typical buffer-sizing methods based on the TCP model are analyzed via the NS2 simulation, and the effects of various high-speed TCP protocols and active queue management (AQM) mechanisms on the buffer-sizing methods in high bandwidth-delay networks are discussed in detail. Simulated results show that: (1) the buffer-sizing methods based on different assumptions adapt to different network environments; (2) the validity of the existing cache mechanisms depends on the ratio of the bandwidth-delay product to the flow number; and (3) when high-speed TCP protocols and AQM mechanisms are used in high bandwidth-delay networks, the buffer size is greatly reduced.%文中针对当今高带宽延迟网络下路由器缓存大小的需求问题,通过NS2仿真实验,对基于TCP协议模型的5种典型的缓存设置方法展开研究,着重分析了在高带宽延迟网络下各种高速TCP协议和主动队列管理(AQM)机制对各种缓存设置方法的影响.仿真实验表明:基于不同假设前提的缓存设置方法适应于不同的网络负载环境;缓存机制的选择取决于网络带宽延迟乘积与流数的比值;在高带宽延迟网络下,当采用高速TCP协议和AQM机制时,缓存需求可以大大减小.

  2. High power, picosecond green laser based on a frequency-doubled, all-fiber, narrow-bandwidth, linearly polarized, Yb-doped fiber laser

    Science.gov (United States)

    Tian, Wenyan; Isyanova, Yelena; Stegeman, Robert; Huang, Ye; Chieffo, Logan R.; Moulton, Peter F.

    2016-03-01

    We report on the development of an all-fiber, 68-kW-peak-power, 16-ps-pulse-width, narrow-bandwidth, linearly polarized, 1064-nm fiber laser suitable for high-power, picosecond-pulse-width, green-light generation. Our 1064-nm fiber laser delivered an average power of up to 110 W at a repetition of 100- MHz in a narrow bandwidth, with minimal nonlinear distortion. We developed a high-power, picosecond green source at 532 nm through use of single-pass frequency-doubling of our 1064-nm fiber laser in lithium triborate (LBO). Using a 15-mm long LBO crystal, we have generated 30 W of average power in the second harmonic with 73-W of fundamental average power, for a conversion efficiency of 41%.

  3. High-Power and High-Efficiency 1.3- µm Superluminescent Diode With Flat-Top and Ultrawide Emission Bandwidth

    KAUST Repository

    Khan, Mohammed Zahed Mustafa

    2015-02-01

    We report on a flat-top and ultrawide emission bandwidth of 125 nm from InGaAsP/InP multiple quantum-well (MQW) superluminescent diode with antireflection coated and tilted ridge-waveguide device configuration. A total output power in excess of 70 mW with an average power spectral density of 0.56 mW/nm and spectral ripple ≤ 1.2 ± 0.5 dB is measured from the device. Wall-plug efficiency and output power as high as 14% and 80 mW, respectively, is demonstrated from this batch of devices. We attribute the broad emission to the inherent inhomogeneity of the electron-heavy-hole (e-hh) and electron-light-hole (e-lh) recombination of the ground state and the first excited state of the MQWs and their simultaneous emission.

  4. Novel high-gain, improved-bandwidth, finned-ladder V-band Traveling-Wave Tube slow-wave circuit design

    Science.gov (United States)

    Kory, Carol L.; Wilson, Jeffrey D.

    1994-01-01

    The V-band frequency range of 59-64 GHz is a region of the millimeter-wave spectrum that has been designated for inter-satellite communications. As a first effort to develop a high-efficiency V-band Traveling-Wave Tube (TWT), variations on a ring-plane slow-wave circuit were computationally investigated to develop an alternative to the more conventional ferruled coupled-cavity circuit. The ring-plane circuit was chosen because of its high interaction impedance, large beam aperture, and excellent thermal dissipation properties. Despite these advantages, however, low bandwidth and high voltage requirements have, until now, prevented its acceptance outside the laboratory. In this paper, the three-dimensional electrodynamic simulation code MAFIA (solution of MAxwell's Equation by the Finite-Integration-Algorithm) is used to investigate methods of increasing the bandwidth and lowering the operating voltage of the ring-plane circuit. Calculations of frequency-phase dispersion, beam on-axis interaction impedance, attenuation and small-signal gain per wavelength were performed for various geometric variations and loading distributions of the ring-plane TWT slow-wave circuit. Based on the results of the variations, a circuit termed the finned-ladder TWT slow-wave circuit was designed and is compared here to the scaled prototype ring-plane and a conventional ferruled coupled-cavity TWT circuit over the V-band frequency range. The simulation results indicate that this circuit has a much higher gain, significantly wider bandwidth, and a much lower voltage requirement than the scaled ring-plane prototype circuit, while retaining its excellent thermal dissipation properties. The finned-ladder circuit has a much larger small-signal gain per wavelength than the ferruled coupled-cavity circuit, but with a moderate sacrifice in bandwidth.

  5. Minimization of the impact of a broad bandwidth high-gain nonlinear preamplifier to the amplified spontaneous emission pedestal of the Vulcan petawatt laser facility.

    Science.gov (United States)

    Musgrave, I O; Hernandez-Gomez, C; Canny, D; Collier, J; Heathcote, R

    2007-10-01

    To generate petawatt pulses using the Vulcan Nd:glass laser requires a broad bandwidth high-gain preamplifier. The preamplifier used is an optical parametric amplifier that provides a total gain of 10(8) in three amplification stages. We report on a detailed investigation of the effect of the Vulcan optical parametric chirped pulse amplification (OPCPA) preamplifier on contrast caused by the amplified spontaneous emission (ASE) pedestal that extends up to 2 ns before the arrival of the main pulse. The contrast after compression is improved to 4x10(8) of the intensity of the main pulse using near-field apertures between the stages of the OPCPA preamplifier. Further reduction of the level of the ASE pedestal can be achieved at the cost of a reduction in amplified bandwidth by solely phosphate glass amplification after initial preamplification rather than a mixed glass amplification scheme.

  6. High-Bandwidth Tactical-Network Data Analysis in a High-Performance-Computing (HPC) Environment: Time Tagging the Data

    Science.gov (United States)

    2015-09-01

    1 ms. 15. SUBJECT TERMS tactical networks, data reduction, high-performance computing, data analysis, big data 16. SECURITY CLASSIFICATION OF...study of WIN-T IOTE ClockModel Issues.7 Fig. 5 Sample long-running ADMAS clock differences (3 clock model states...of the total cuts recorded (on the order of 0.00001% of cuts recorded). 7. Adametz J, McGowan J. Case study of WIN-T IOTE ClockModel issues

  7. High-Bandwidth Tactical-Network Data Analysis in a High-Performance-Computing (HPC) Environment: Introduction

    Science.gov (United States)

    2015-09-01

    ability to transport voice and data messages, with high assurance and minimal delays, as the unit maneuvers to accomplish its mission. Tactical...critical to such analysis efforts, in addition to metrics drawn from application-level interactions, such as Voice over futemet Protocol (VoiP...Network Performance Statistics. These provide information on the state of IP routing tables and radio-level connections, which informs the overall

  8. Generation of a spectrum with high flatness and high bandwidth in a short length of telecom fiber using microchip laser

    Science.gov (United States)

    Hernandez-Garcia, J. C.; Estudillo-Ayala, J. M.; Pottiez, O.; Rojas-Laguna, R.; Mata-Chavez, R. I.; Gonzalez-Garcia, A.

    2013-04-01

    In this work, we studied experimentally the generation of a supercontinuum spectrum induced in a piece of standard single-mode fiber using pulses from a microchip laser. For different values of fiber length, we obtained spectra with high flatness in visible and IR regions. The possibility to generate a spectrum with a high flatness and spectral width of more than ˜1100 nm (600 nm to over 1700 nm) in relatively short lengths of telecom fiber (˜57 m), using as the pump pulses with no more than a few kW peak power at a non-zero-dispersion wavelength, is attributed to the peculiar properties of the pulses generated by the pump source. The physical processes leading to the formation of the supercontinuum spectrum were studied by monitoring the growth of the spectrum while increasing the input power. The coupling efficiency between the microchip laser and the telecom fiber helped us obtain a very wide spectrum. This work shows that the use of conventional fiber for supercontinuum generation can be viewed as a cheap and efficient option, in particular for applications like optical metrology, coherence tomography and low noise sources for the characterization of devices.

  9. Optimal signal bandwidth for the recording of surface EMG activity of facial, jaw, oral, and neck muscles

    NARCIS (Netherlands)

    van Boxtel, A.

    2001-01-01

    Spontaneous pericranial electromyographic (EMG) activity is generally small and is contaminated by strong low-frequency artifacts. High-pass filtering should suppress artifacts but affect EMG signal power only minimally. In 24 subjects who performed a warned simple reaction time task, the optimal hi

  10. Laser damage comparisons of broad-bandwidth, high-reflection optical coatings containing TiO2, Nb2O5, or Ta2O5 high-index layers

    Science.gov (United States)

    Field, Ella S.; Bellum, John C.; Kletecka, Damon E.

    2017-01-01

    Broad bandwidth coatings allow angle of incidence flexibility and accommodate spectral shifts due to aging and water absorption. Higher refractive index materials in optical coatings, such as TiO2, Nb2O5, and Ta2O5, can be used to achieve broader bandwidths compared to coatings that contain HfO2 high index layers. We have identified the deposition settings that lead to the highest index, lowest absorption layers of TiO2, Nb2O5, and Ta2O5, via e-beam evaporation using ion-assisted deposition. We paired these high index materials with SiO2 as the low index material to create broad bandwidth high reflection coatings centered at 1054 nm for 45 deg angle of incidence and P polarization. High reflection bandwidths as large as 231 nm were realized. Laser damage tests of these coatings using the ISO 11254 and NIF-MEL protocols are presented, which revealed that the Ta2O5/SiO2 coating exhibits the highest resistance to laser damage, at the expense of lower bandwidth compared to the TiO2/SiO2 and Nb2O5/SiO2 coatings.

  11. Chemical Industry Bandwidth Study

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2006-12-01

    The Chemical Bandwidth Study provides a snapshot of potentially recoverable energy losses during chemical manufacturing. The advantage of this study is the use of "exergy" analysis as a tool for pinpointing inefficiencies.

  12. Bandwidth efficient coding

    CERN Document Server

    Anderson, John B

    2017-01-01

    Bandwidth Efficient Coding addresses the major challenge in communication engineering today: how to communicate more bits of information in the same radio spectrum. Energy and bandwidth are needed to transmit bits, and bandwidth affects capacity the most. Methods have been developed that are ten times as energy efficient at a given bandwidth consumption as simple methods. These employ signals with very complex patterns and are called "coding" solutions. The book begins with classical theory before introducing new techniques that combine older methods of error correction coding and radio transmission in order to create narrowband methods that are as efficient in both spectrum and energy as nature allows. Other topics covered include modulation techniques such as CPM, coded QAM and pulse design.

  13. Industrial Glass Bandwidth Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Rue, David M. [Gas Technology Inst., Des Plaines, IL (United States); Servaites, James [Gas Technology Inst., Des Plaines, IL (United States); Wolf, Warren [Gas Technology Inst., Des Plaines, IL (United States)

    2007-08-01

    This is a study on energy use and potential savings, or "bandwidth" study, for several glassmaking processes. Intended to provide a realistic estimate of the potential amount of energy that can be saved in an industrial process, the "bandwidth" refers to the difference between the amount of energy that would be consumed in a process using commercially available technology versus the minimum amount of energy needed to achieve those same results.

  14. Glass Industry Bandwidth Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Rue, David M. [Gas Technology Inst., Des Plaines, IL (United States)

    2006-07-01

    This is a study on energy use and potential savings, or "bandwidth" study, for several glassmaking processes. Intended to provide a realistic estimate of the potential amount of energy that can be saved in an industrial process, the "bandwidth" refers to the difference between the amount of energy that would be consumed in a process using commercially available technology versus the minimum amount of energy needed to achieve those same results.

  15. Industrial Glass Bandwidth Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Rue, David M. [Gas Technology Inst., Des Plaines, IL (United States); Servaites, James [Gas Technology Inst., Des Plaines, IL (United States); Wolf, Warren [Gas Technology Inst., Des Plaines, IL (United States)

    2007-08-01

    This is a study on energy use and potential savings, or "bandwidth" study, for several glassmaking processes. Intended to provide a realistic estimate of the potential amount of energy that can be saved in an industrial process, the "bandwidth" refers to the difference between the amount of energy that would be consumed in a process using commercially available technology versus the minimum amount of energy needed to achieve those same results.

  16. Glass Industry Bandwidth Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Rue, David M. [Gas Technology Inst., Des Plaines, IL (United States)

    2006-07-01

    This is a study on energy use and potential savings, or "bandwidth" study, for several glassmaking processes. Intended to provide a realistic estimate of the potential amount of energy that can be saved in an industrial process, the "bandwidth" refers to the difference between the amount of energy that would be consumed in a process using commercially available technology versus the minimum amount of energy needed to achieve those same results.

  17. Bandwidth challenge teams at SC2003 conference

    CERN Multimedia

    2003-01-01

    Results from the fourth annual High-Performance Bandwidth Challenge, held in conjunction with SC2003, the international conference on high-performance computing and networking which occurred last week in Phoenix, AZ (1 page).

  18. Bandwidth Reconfigurable Metamaterial Arrays

    Directory of Open Access Journals (Sweden)

    Nathanael J. Smith

    2014-01-01

    Full Text Available Metamaterial structures provide innovative ways to manipulate electromagnetic wave responses to realize new applications. This paper presents a conformal wideband metamaterial array that achieves as much as 10 : 1 continuous bandwidth. This was done by using interelement coupling to concurrently achieve significant wave slow-down and cancel the inductance stemming from the ground plane. The corresponding equivalent circuit of the resulting array is the same as that of classic metamaterial structures. In this paper, we present a wideband Marchand-type balun with validation measurements demonstrating the metamaterial (MTM array’s bandwidth from 280 MHz to 2800 MHz. Bandwidth reconfiguration of this class of array is then demonstrated achieving a variety of band-pass or band-rejection responses within its original bandwidth. In contrast with previous bandwidth and frequency response reconfigurations, our approach does not change the aperture’s or ground plane’s geometry, nor does it introduce external filtering structures. Instead, the new responses are realized by making simple circuit changes into the balanced feed integrated with the wideband MTM array. A variety of circuit changes can be employed using MEMS switches or variable lumped loads within the feed and 5 example band-pass and band-rejection responses are presented. These demonstrate the potential of the MTM array’s reconfiguration to address a variety of responses.

  19. Bimodal-sized quantum dots for broad spectral bandwidth emitter.

    Science.gov (United States)

    Zhou, Yinli; Zhang, Jian; Ning, Yongqiang; Zeng, Yugang; Zhang, Jianwei; Zhang, Xing; Qin, Li; Wang, Lijun

    2015-12-14

    In this work, a high-power and broadband superluminescent diode (SLD) is achieved utilizing bimodal-sized quantum dots (QDs) as active materials. The device exhibits a 3 dB bandwidth of 178.8 nm with output power of 1.3 mW under continuous-wave (CW) conditions. Preliminary discussion attributes the spectra behavior of the device to carrier transfer between small dot ensemble and large dot ensemble. Our result provides a new possibility to further broadening the spectral bandwidth and improving the CW output power of QD-SLDs.

  20. Bandwidth in bolometric interferometry

    Science.gov (United States)

    Charlassier, R.; Bunn, E. F.; Hamilton, J.-Ch.; Kaplan, J.; Malu, S.

    2010-05-01

    Context. Bolometric interferometry is a promising new technology with potential applications to the detection of B-mode polarization fluctuations of the cosmic microwave background (CMB). A bolometric interferometer will have to take advantage of the wide spectral detection band of its bolometers to be competitive with imaging experiments. A crucial concern is that interferometers are assumed to be significantly affected by a spoiling effect known as bandwidth smearing. Aims: We investigate how the bandwidth modifies the work principle of a bolometric interferometer and affects its sensitivity to the CMB angular power spectra. Methods: We obtain analytical expressions for the broadband visibilities measured by broadband heterodyne and bolometric interferometers. We investigate how the visibilities must be reconstructed in a broadband bolometric interferometer and show that this critically depends on hardware properties of the modulation phase shifters. If the phase shifters produce shifts that are constant with respect to frequency, the instrument works like its monochromatic version (the modulation matrix is not modified), while if they vary (linearly or otherwise) with respect to frequency, one has to perform a special reconstruction scheme, which allows the visibilities to be reconstructed in frequency subbands. Using an angular power spectrum estimator that accounts for the bandwidth, we finally calculate the sensitivity of a broadband bolometric interferometer. A numerical simulation is performed that confirms the analytical results. Results: We conclude that (i) broadband bolometric interferometers allow broadband visibilities to be reconstructed regardless of the type of phase shifters used and (ii) for dedicated B-mode bolometric interferometers, the sensitivity loss caused by bandwidth smearing is quite acceptable, even for wideband instruments (a factor of 2 loss for a typical 20% bandwidth experiment).

  1. Live Educational Outreach for Ocean Exploration: High-Bandwidth Ship-to-Shore Broadcasts Using Internet2

    Science.gov (United States)

    Coleman, D. F.; Ballard, R. D.

    2005-12-01

    During the past 3 field seasons, our group at the University of Rhode Island Graduate School of Oceanography, in partnership with the Institute for Exploration and a number of educational institutions, has conducted a series of ocean exploration expeditions with a significant focus on educational outreach through "telepresence" - utilizing live transmissions of video, audio, and data streams across the Internet and Internet2. Our educational partners include Immersion Presents, Boys and Girls Clubs of America, the Jason Foundation for Education, and the National Geographic Society, all who provided partial funding for the expeditions. The primary funding agency each year was NOAA's Office of Ocean Exploration and our outreach efforts were conducted in collaboration with them. During each expedition, remotely operated vehicle (ROV) systems were employed to examine interesting geological and archaeological sites on the seafloor. These expeditions include the investigation of ancient shipwrecks in the Black Sea in 2003, a survey of the Titanic shipwreck site in 2004, and a detailed sampling and mapping effort at the Lost City Hydrothermal Field in 2005. High-definition video cameras on the ROVs collected the footage that was then digitally encoded, IP-encapsulated, and streamed across a satellite link to a shore-based hub, where the streams were redistributed. During each expedition, live half-hour-long educational broadcasts were produced 4 times per day for 10 days. These shows were distributed using satellite and internet technologies to a variety of venues, including museums, aquariums, science centers, public schools, and universities. In addition to the live broadcasts, educational products were developed to enhance the learning experience. These include activity modules and curriculum-based material for teachers and informal educators. Each educational partner also maintained a web site that followed the expedition and provided additional background information

  2. Bandwidth in bolometric interferometry

    CERN Document Server

    Charlassier, R; Hamilton, J -Ch; Kaplan, J; Malu, S

    2009-01-01

    Bolometric Interferometry is a technology currently under development that will be first dedicated to the detection of B-mode polarization fluctuations in the Cosmic Microwave Background. A bolometric interferometer will have to take advantage of the wide spectral detection band of its bolometers in order to be competitive with imaging experiments. A crucial concern is that interferometers are presumed to be importantly affected by a spoiling effect known as bandwidth smearing. In this paper, we investigate how the bandwidth modifies the work principle of a bolometric interferometer and how it affects its sensitivity to the CMB angular power spectra. We obtain analytical expressions for the broadband visibilities measured by broadband heterodyne and bolometric interferometers. We investigate how the visibilities must be reconstructed in a broadband bolometric interferometer and show that this critically depends on hardware properties of the modulation phase shifters. Using an angular power spectrum estimator ...

  3. Optical conductivity measurements of GaTa4Se8 under high pressure: evidence of a bandwidth-controlled insulator-to-metal Mott transition.

    Science.gov (United States)

    Ta Phuoc, V; Vaju, C; Corraze, B; Sopracase, R; Perucchi, A; Marini, C; Postorino, P; Chligui, M; Lupi, S; Janod, E; Cario, L

    2013-01-18

    The optical properties of a GaTa(4)Se(8) single crystal are investigated under high pressure. At ambient pressure, the optical conductivity exhibits a charge gap of ≈0.12 eV and a broad midinfrared band at ≈0.55 eV. As pressure is increased, the low energy spectral weight is strongly enhanced and the optical gap is rapidly filled, pointing to an insulator to metal transition around 6 GPa. The overall evolution of the optical conductivity demonstrates that GaTa(4)Se(8) is a Mott insulator which undergoes a bandwidth-controlled Mott metal-insulator transition under pressure, in remarkably good agreement with theory. With the use of our optical data and ab initio band structure calculations, our results were successfully compared to the (U/D, T/D) phase diagram predicted by dynamical mean field theory for strongly correlated systems.

  4. Bandwidth Trading as Incentive

    Science.gov (United States)

    Eger, Kolja; Killat, Ulrich

    In P2P networks with multi-source download the file of interest is fragmented into pieces and peers exchange pieces with each other although they did not finish the download of the complete file. Peers can adopt different strategies to trade upload for download bandwidth. These trading schemes should give peers an incentive to contribute bandwidth to the P2P network. This chapter studies different trading schemes analytically and by simulations. A mathematical framework for bandwidth trading is introduced and two distributed algorithms, which are denoted as Resource Pricing and Reciprocal Rate Control, are derived. The algorithms are compared to the tit-for-tat principle in BitTorrent. Nash Equilibria and results from simulations of static and dynamic networks are presented. Additionally, we discuss how trading schemes can be combined with a piece selection algorithm to increase the availability of a full copy of the file. The chapter closes with an extension of the mathematical model which takes also the underlying IP network into account. This results in a TCP variant optimised for P2P content distribution.

  5. Polybinary modulation for bandwidth limited optical links

    DEFF Research Database (Denmark)

    Vegas Olmos, Juan José; Jurado-Navas, Antonio

    2015-01-01

    Optical links using traditional modulation formats are reaching a plateau in terms of capacity, mainly due to bandwidth limitations in the devices employed at the transmitter and receivers. Advanced modulation formats, which boost the spectral efficiency, provide a smooth migration path towards...... the recent results on poly binary modulation, comprising both binary and multilevel signals as seed signals. The results will show how poly binary modulation effectively reduces the bandwidth requirements on optical links while providing high spectral efficiency....

  6. Spectrophotometer spectral bandwidth calibration with absorption bands crystal standard.

    Science.gov (United States)

    Soares, O D; Costa, J L

    1999-04-01

    A procedure for calibration of a spectral bandwidth standard for high-resolution spectrophotometers is described. Symmetrical absorption bands for a crystal standard are adopted. The method relies on spectral band shape fitting followed by a convolution with the slit function of the spectrophotometer. A reference spectrophotometer is used to calibrate the spectral bandwidth standard. Bandwidth calibration curves for a minimum spectral transmission factor relative to the spectral bandwidth of the reference spectrophotometer are derived for the absorption bands at the wavelength of the band absorption maximum. The family of these calibration curves characterizes the spectral bandwidth standard. We calibrate the spectral bandwidth of a spectrophotometer with respect to the reference spectrophotometer by determining the spectral transmission factor minimum at every calibrated absorption band of the bandwidth standard for the nominal instrument values of the spectral bandwidth. With reference to the standard spectral bandwidth calibration curves, the relation of the spectral bandwidth to the reference spectrophotometer is determined. We determine the discrepancy in the spectrophotometers' spectral bandwidths by averaging the spectral bandwidth discrepancies relative to the standard calibrated values found at the absorption bands considered. A weighted average of the uncertainties is taken.

  7. 3Dwheel: 3-axis low-noise, high-bandwidth attitude actuation from a single momentum wheel using magnetic bearings.

    OpenAIRE

    Seddon, Jon; Pechev, Alexandre

    2009-01-01

    This paper proposes a new concept for attitude actuation for small satellites that uses active magnetic bearings to support and tilt a spinning rotor to provide 3-axis attitude control of the satellite using a single actuator. A controlled 3D motion in the spinning rotor provides a conventional torque output about the momentum axis and a gyroscopic torque output about any direction in the plane normal to the spinning axis. Therefore, a single tilting momentum-wheel can generate torque along t...

  8. Topology optimization of photonic crystal structures: a high-bandwidth low-loss T-junction waveguide

    DEFF Research Database (Denmark)

    Jensen, Jakob Søndergaard; Sigmund, Ole

    2005-01-01

    A T junction in a photonic crystal waveguide is designed with the topology-optimization method. The gradientbased optimization tool is used to modify the material distribution in the junction area so that the power transmission in the output ports is maximized. To obtain high transmission...

  9. Health care using high-bandwidth communication to overcome distance and time barriers for the Department of Defense

    Science.gov (United States)

    Mun, Seong K.; Freedman, Matthew T.; Gelish, Anthony; de Treville, Robert E.; Sheehy, Monet R.; Hansen, Mark; Hill, Mac; Zacharia, Elisabeth; Sullivan, Michael J.; Sebera, C. Wayne

    1993-01-01

    Image management and communications (IMAC) network, also known as picture archiving and communication system (PACS) consists of (1) digital image acquisition, (2) image review station (3) image storage device(s), image reading workstation, and (4) communication capability. When these subsystems are integrated over a high speed communication technology, possibilities are numerous in improving the timeliness and quality of diagnostic services within a hospital or at remote clinical sites. Teleradiology system uses basically the same hardware configuration together with a long distance communication capability. Functional characteristics of components are highlighted. Many medical imaging systems are already in digital form. These digital images constitute approximately 30% of the total volume of images produced in a radiology department. The remaining 70% of images include conventional x-ray films of the chest, skeleton, abdomen, and GI tract. Unless one develops a method of handling these conventional film images, global improvement in productivity in image management and radiology service throughout a hospital cannot be achieved. Currently, there are two method of producing digital information representing these conventional analog images for IMAC: film digitizers that scan the conventional films, and computed radiography (CR) that captures x-ray images using storage phosphor plate that is subsequently scanned by a laser beam.

  10. Bandwidth Estimation For Mobile Ad hoc Network (MANET

    Directory of Open Access Journals (Sweden)

    Rabia Ali

    2011-09-01

    Full Text Available In this paper we presents bandwidth estimation scheme for MANET, which uses some components of the two methods for the bandwidth estimation: 'Hello Bandwidth Estimation 'Listen Bandwidth Estimation. This paper also gives the advantages of the proposed method. The proposed method is based on the comparison of these two methods. Bandwidth estimation is an important issue in the Mobile Ad-hoc Network (MANET because bandwidth estimation in MANET is difficult, because each host has imprecise knowledge of the network status and links change dynamically. Therefore, an effective bandwidth estimation scheme for MANET is highly desirable. Ad hoc networks present unique advanced challenges, including the design of protocols for mobility management, effective routing, data transport, security, power management, and quality-of-service (QoS provisioning. Once these problems are solved, the practical use of MANETs will be realizable.

  11. Ultrahigh bandwidth signal processing

    DEFF Research Database (Denmark)

    Oxenløwe, Leif Katsuo

    2016-01-01

    Optical time lenses have proven to be very versatile for advanced optical signal processing. Based on a controlled interplay between dispersion and phase-modulation by e.g. four-wave mixing, the processing is phase-preserving, an hence useful for all types of data signals including coherent multi......-level modulation founats. This has enabled processing of phase-modulated spectrally efficient data signals, such as orthogonal frequency division multiplexed (OFDM) signa In that case, a spectral telescope system was used, using two time lenses with different focal lengths (chirp rates), yielding a spectral...... regeneratio These operations require a broad bandwidth nonlinear platform, and novel photonic integrated nonlinear platform like aluminum gallium arsenide nano-waveguides used for 1.28 Tbaud optical signal processing will be described....

  12. Bandwidth enhancement and time-delay signature suppression of chaotic signal from an optical feedback semiconductor laser by using cross phase modulation in a highly nonlinear fiber loop mirror

    Science.gov (United States)

    Wang, Liang-Yan; Zhong, Zhu-Qiong; Wu, Zheng-Mao; Lu, Dong; Chen, Xi; Chen, Jun; Xia, Guang-Qiong

    2016-11-01

    Based on a nonlinear fiber loop mirror (NOLM) composed of a fiber coupler (FC) and a highly nonlinear fiber (HNLF), a scheme is proposed to simultaneously realize the bandwidth enhancement and the time-delay signature (TDS) suppression of a chaotic signal generated from an external cavity optical feedback semiconductor laser. The simulation results show that, after passing through the NOLM, the bandwidth of chaotic signal can be efficiently enhanced and the TDS can be well suppressed under suitable operation parameters. Furthermore, the influences of the power-splitting ratio of the FC, the averaged power of the chaotic signal entering into the FC and the length of the HNLF on the chaotic bandwidth and TDS are analyzed, and the optimized parameters are determined.

  13. Efficient Bandwidth Management for Ethernet Passive Optical Networks

    KAUST Repository

    Elrasad, Amr Elsayed M.

    2016-05-15

    Polling (EGSIP), to compensate the unutilized bandwidth due to frame delineation. Our solution achieves delay reduction ratio up to 90% at high load. We also develop a Congestion Aware Limited Time (CALT) DBA scheme to detect and resolve temporary congestion in EPONs. CALT smartly adapts the optical networking unit (ONU) maximum transmission window according to the detected congestion level. Numerical results show that CALT is more robust at high load compared to other related published schemes. Regarding LR-EPONs, the main concern is large round trip delay mitigation. We address two problems, namely bandwidth over-granting in Multi-Thread Polling (MTP) and on-the-fly void filling. We combine, with some modifications, EGSIP and DES to resolve bandwidth over-granting in MTP. We also manage to adaptively tune MTP active running threads along with the offered load. Regarding on-the-fly void filling, Our approach, Parallel Void Thread (PVT), achieves large delay reduction for delay-sensitive traffic. PVT is designed as a plus function to DBA and can be combined with almost all DBA schemes proposed before. The powerful feature of our proposed solutions is integrability. We integrate our solutions together and form a multi-feature, robust, fairly simple, and well performing DBA scheme over LR-TWDM-EPONs. Our final contribution is about energy saving under target delay constraints. We tackle the problem of downstream based sleep time sizing and scheduling under required delay constraints. Simulation results show that our approach adheres to delay constraints and achieves almost ideal energy saving ratio at the same time.

  14. 37 GHz Direct-Modulation Bandwidth of Multi-Section InGaAsP/InP DBR-Laser with weakly coupled active grating section

    DEFF Research Database (Denmark)

    Kaiser, W.; Bach, L.; Reithmaier, J. P.;

    2003-01-01

    37 GHz direct-modulation bandwidth could be obtained by a multi-section design with an integrated weakly coupled DBR grating. The laser shows side mode suppression ratios of 45 dB and output powers exceeding 20 mW.......37 GHz direct-modulation bandwidth could be obtained by a multi-section design with an integrated weakly coupled DBR grating. The laser shows side mode suppression ratios of 45 dB and output powers exceeding 20 mW....

  15. Ultrahigh bandwidth signal processing

    Science.gov (United States)

    Oxenløwe, Leif Katsuo

    2016-04-01

    Optical time lenses have proven to be very versatile for advanced optical signal processing. Based on a controlled interplay between dispersion and phase-modulation by e.g. four-wave mixing, the processing is phase-preserving, and hence useful for all types of data signals including coherent multi-level modulation formats. This has enabled processing of phase-modulated spectrally efficient data signals, such as orthogonal frequency division multiplexed (OFDM) signals. In that case, a spectral telescope system was used, using two time lenses with different focal lengths (chirp rates), yielding a spectral magnification of the OFDM signal. Utilising such telescopic arrangements, it has become possible to perform a number of interesting functionalities, which will be described in the presentation. This includes conversion from OFDM to Nyquist WDM, compression of WDM channels to a single Nyquist channel and WDM regeneration. These operations require a broad bandwidth nonlinear platform, and novel photonic integrated nonlinear platforms like aluminum gallium arsenide nano-waveguides used for 1.28 Tbaud optical signal processing will be described.

  16. Theoretical Calculation of MMF's Bandwidth

    Institute of Scientific and Technical Information of China (English)

    LI Xiao-fu; JIANG De-sheng; YU Hai-hu

    2004-01-01

    The difference between over-filled launch bandwidth (OFL BW) and restricted mode launch bandwidth (RML BW) is described. A theoretical model is founded to calculate the OFL BW of grade index multimode fiber (GI-MMF),and the result is useful to guide the modification of the manufacturing method.

  17. Estimating Bottleneck Bandwidth using TCP

    Science.gov (United States)

    Allman, Mark

    1998-01-01

    Various issues associated with estimating bottleneck bandwidth using TCP are presented in viewgraph form. Specific topics include: 1) Why TCP is wanted to estimate the bottleneck bandwidth; 2) Setting ssthresh to an appropriate value to reduce loss; 3) Possible packet-pair solutions; and 4) Preliminary results: ACTS and the Internet.

  18. Bandwidth of Gaussian weighted Chirp

    DEFF Research Database (Denmark)

    Wilhjelm, Jens E.

    1993-01-01

    Four major time duration and bandwidth expressions are calculated for a linearly frequency modulated sinusoid with Gaussian shaped envelope. This includes a Gaussian tone pulse. The bandwidth is found to be a nonlinear function of nominal time duration and nominal frequency excursion of the chirp...

  19. Improved-Bandwidth Transimpedance Amplifier

    Science.gov (United States)

    Chapsky, Jacob

    2009-01-01

    The widest available operational amplifier, with the best voltage and current noise characteristics, is considered for transimpedance amplifier (TIA) applications where wide bandwidth is required to handle fast rising input signals (as for time-of-flight measurement cases). The added amplifier inside the TIA feedback loop can be configured to have slightly lower voltage gain than the bandwidth reduction factor.

  20. Compact antenna arrays with wide bandwidth and low sidelobe levels

    Science.gov (United States)

    Strassner, II, Bernd H.

    2014-09-09

    Highly efficient, low cost, easily manufactured SAR antenna arrays with lightweight low profiles, large instantaneous bandwidths and low SLL are disclosed. The array topology provides all necessary circuitry within the available antenna aperture space and between the layers of material that comprise the aperture. Bandwidths of 15.2 GHz to 18.2 GHz, with 30 dB SLLs azimuthally and elevationally, and radiation efficiencies above 40% may be achieved. Operation over much larger bandwidths is possible as well.

  1. VisIO: enabling interactive visualization of ultra-scale, time-series data via high-bandwidth distributed I/O systems

    Energy Technology Data Exchange (ETDEWEB)

    Mitchell, Christopher J [Los Alamos National Laboratory; Ahrens, James P [Los Alamos National Laboratory; Wang, Jun [UCF

    2010-10-15

    Petascale simulations compute at resolutions ranging into billions of cells and write terabytes of data for visualization and analysis. Interactive visuaUzation of this time series is a desired step before starting a new run. The I/O subsystem and associated network often are a significant impediment to interactive visualization of time-varying data; as they are not configured or provisioned to provide necessary I/O read rates. In this paper, we propose a new I/O library for visualization applications: VisIO. Visualization applications commonly use N-to-N reads within their parallel enabled readers which provides an incentive for a shared-nothing approach to I/O, similar to other data-intensive approaches such as Hadoop. However, unlike other data-intensive applications, visualization requires: (1) interactive performance for large data volumes, (2) compatibility with MPI and POSIX file system semantics for compatibility with existing infrastructure, and (3) use of existing file formats and their stipulated data partitioning rules. VisIO, provides a mechanism for using a non-POSIX distributed file system to provide linear scaling of 110 bandwidth. In addition, we introduce a novel scheduling algorithm that helps to co-locate visualization processes on nodes with the requested data. Testing using VisIO integrated into Para View was conducted using the Hadoop Distributed File System (HDFS) on TACC's Longhorn cluster. A representative dataset, VPIC, across 128 nodes showed a 64.4% read performance improvement compared to the provided Lustre installation. Also tested, was a dataset representing a global ocean salinity simulation that showed a 51.4% improvement in read performance over Lustre when using our VisIO system. VisIO, provides powerful high-performance I/O services to visualization applications, allowing for interactive performance with ultra-scale, time-series data.

  2. Optimal resource allocation in random networks with transportation bandwidths

    Science.gov (United States)

    Yeung, C. H.; Wong, K. Y. Michael

    2009-03-01

    We apply statistical physics to study the task of resource allocation in random sparse networks with limited bandwidths for the transportation of resources along the links. Recursive relations from the Bethe approximation are converted into useful algorithms. Bottlenecks emerge when the bandwidths are small, causing an increase in the fraction of idle links. For a given total bandwidth per node, the efficiency of allocation increases with the network connectivity. In the high connectivity limit, we find a phase transition at a critical bandwidth, above which clusters of balanced nodes appear, characterized by a profile of homogenized resource allocation similar to the Maxwell construction.

  3. Upgrade trigger: Bandwidth strategy proposal

    CERN Document Server

    Fitzpatrick, Conor; Meloni, Simone; Boettcher, Thomas Julian; Whitehead, Mark Peter; Dziurda, Agnieszka; Vesterinen, Mika Anton

    2017-01-01

    This document describes a selection strategy for the upgrade trigger using charm signals as a benchmark. The Upgrade trigger uses a 'Run 2-like' sequence consisting of a first and second stage, in between which the calibration and alignment is performed. The first stage, HLT1, uses an inclusive strategy to select beauty and charm decays, while the second stage uses offline-quality exclusive selections. A novel genetic algorithm-based bandwidth division is performed at the second stage to distribute the output bandwidth among different physics channels, maximising the efficiency for useful physics events. The performance is then studied as a function of the available output bandwidth.

  4. High-Bandwidth AFM-Based Rheology Reveals that Cartilage is Most Sensitive to High Loading Rates at Early Stages of Impairment

    Science.gov (United States)

    Nia, Hadi Tavakoli; Bozchalooi, Iman S.; Li, Yang; Han, Lin; Hung, Han-Hwa; Frank, Eliot; Youcef-Toumi, Kamal; Ortiz, Christine; Grodzinsky, Alan

    2013-01-01

    Utilizing a newly developed atomic-force-microscopy-based wide-frequency rheology system, we measured the dynamic nanomechanical behavior of normal and glycosaminoglycan (GAG)-depleted cartilage, the latter representing matrix degradation that occurs at the earliest stages of osteoarthritis. We observed unique variations in the frequency-dependent stiffness and hydraulic permeability of cartilage in the 1 Hz-to-10 kHz range, a frequency range that is relevant to joint motions from normal ambulation to high-frequency impact loading. Measurement in this frequency range is well beyond the capabilities of typical commercial atomic force microscopes. We showed that the dynamic modulus of cartilage undergoes a dramatic alteration after GAG loss, even with the collagen network still intact: whereas the magnitude of the dynamic modulus decreased two- to threefold at higher frequencies, the peak frequency of the phase angle of the modulus (representing fluid-solid frictional dissipation) increased 15-fold from 55 Hz in normal cartilage to 800 Hz after GAG depletion. These results, based on a fibril-reinforced poroelastic finite-element model, demonstrated that GAG loss caused a dramatic increase in cartilage hydraulic permeability (up to 25-fold), suggesting that early osteoarthritic cartilage is more vulnerable to higher loading rates than to the conventionally studied “loading magnitude”. Thus, over the wide frequency range of joint motion during daily activities, hydraulic permeability appears the most sensitive marker of early tissue degradation. PMID:23561529

  5. High-Bandwidth, High-Efficiency Envelope Tracking Power Supply for 40W RF Power Amplifier Using Paralleled Bandpass Current Sources

    DEFF Research Database (Denmark)

    Høyerby, Mikkel Christian Wendelboe; Andersen, Michael Andreas E.

    2005-01-01

    This paper presents a high-performance power conversion scheme for power supply applications that require very high output voltage slew rates (dV/dt). The concept is to parallel 2 switching bandpass current sources, each optimized for its passband frequency space and the expected load current....... The principle is demonstrated with a power supply, designed for supplying a 40 W linear RF power amplifier for efficient amplification of a 16-QAM modulated data stream...

  6. 高灵敏度微小卫星可变带宽接收机设计%Design of variable loop bandwidth high sensitivity micro-satellite receiver

    Institute of Scientific and Technical Information of China (English)

    张朝杰; 金小军; 杨伟君; 金仲和

    2011-01-01

    针对微小卫星发射功率低、天线增益小的特点对星载测控应答机提出的高接收灵敏度及高动态范围要求,研究卫星接收机的实现方法.提出一种基于正交欠采样技术及全数字载波恢复环的可变带宽卫星接收机结构.在全数字载波恢复环的实现中,通过相干自动增益控制(AGC)来控制环路带宽,使得在高信噪比下的环路带宽增大,从而获得更佳的跟踪性能;在低信噪比下,降低环路带宽使得接收机有更高的接收灵敏度.经实验测试可知,在250Hz环路带宽下,接收灵敏度为-144 dBm,动态范围达到80 dB以上.%The characteristic of low transmit power and antenna gain in micro-satellite requires high receiver sensitivity and high dynamic range for board transponders. A variable loop bandwidth receiver architecture based on all digital carrier recovery loop was presented using I/Q sub-sampling technique. A coherent automatic gain control (AGC) was used in order to control the loop bandwidth. The loop bandwidth was expanded to achieve better tracking performance at high signal to noise ratio; the loop bandwidth was decreased to realize high receiver sensitivity at low signal to noise ratio. -144 dBm receiver sensitivity was achieved and the dynamic range was better than 80 dB under the condition of 250 Hz loop bandwidth.

  7. A digital calibration technique for an ultra high-speed wide-bandwidth folding and interpolating analog-to-digital converter in 0.18-μm CMOS technology*

    Institute of Scientific and Technical Information of China (English)

    Yu Jinshan; Zhang Ruitao; Zhang Zhengping; Wang Yonglu; Zhu Can; Zhang Lei; Yu Zhou; Han Yong

    2011-01-01

    A digital calibration technique for an ultra high-speed folding and interpolating analog-to-digital converter in 0.18-μm CMOS technology is presented. The similar digital calibration techniques are taken for high 3-bit flash converter and low 5-bit folding and interpolating converter, which are based on well-designed calibration reference, calibration DAC and comparators. The spice simulation and the measured results show the ADC produces 5.9 ENOB with calibration disabled and 7.2 ENOB with calibration enabled for high-frequency wide-bandwidth analog input.

  8. Black Holes, Bandwidths and Beethoven

    CERN Document Server

    Kempf, A

    2000-01-01

    It is usually believed that a function whose Fourier spectrum is bounded can vary at most as fast as its highest frequency component. This is in fact not the case, as Aharonov, Berry and others drastically demonstrated with explicit counter examples, so-called superoscillations. The claim is that even the recording of an entire Beethoven symphony can occur as part of a signal with 1Hz bandwidth. Superoscillations have been suggested to account e.g. for transplanckian frequencies of black hole radiation. Here, we give an exact proof for generic superoscillations. Namely, we show that for every fixed bandwidth there exist functions which pass through any finite number of arbitrarily prespecified points. Further, we show that the behavior of bandlimited functions can be reliably characterized through an uncertainty relation for the standard deviation of the signals' samples taken at the Nyquist rate. This uncertainty relation generalizes to time-varying bandwidths.

  9. Upgrade trigger: Bandwidth strategy proposal

    CERN Document Server

    Boettcher, Thomas Julian; Meloni, Simone; Whitehead, Mark Peter; Williams, Mark Richard James

    2017-01-01

    This document describes a proposed selection strategy for the upgrade trigger using charm signals as a benchmark. The Upgrade trigger uses a 'Run2-like' sequence consisting of a first and second stage, in between which the calibration and alignment is performed. The first stage, HLT1, uses an inclusive strategy to select beauty and charm, while the second stage uses offline-quality exclusive selections. A novel genetic algorithm-based bandwidth division is performed at the second stage to maximise the output of useful physics events, and a range of possible signal efficiencies are presented as a function of the available bandwidth.

  10. Mining Industry Energy Bandwidth Study

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2007-07-01

    The Industrial Technologies Program (ITP) relies on analytical studies to identify large energy reduction opportunities in energy-intensive industries and uses these results to guide its R&D portfolio. The energy bandwidth illustrates the total energy-saving opportunity that exists in the industry if the current processes are improved by implementing more energy-efficient practices and by using advanced technologies. This bandwidth analysis report was conducted to assist the ITP Mining R&D program in identifying energy-saving opportunities in coal, metals, and mineral mining. These opportunities were analyzed in key mining processes of blasting, dewatering, drilling, digging, ventilation, materials handling, crushing, grinding, and separations.

  11. Optimization of Single-Sensor Two-State Hot-Wire Anemometer Transmission Bandwidth.

    Science.gov (United States)

    Ligęza, Paweł

    2008-10-28

    Hot-wire anemometric measurements of non-isothermal flows require the use of thermal compensation or correction circuitry. One possible solution is a two-state hot-wire anemometer that uses the cyclically changing heating level of a single sensor. The area in which flow velocity and fluid temperature can be measured is limited by the dimensions of the sensor's active element. The system is designed to measure flows characterized by high velocity and temperature gradients, although its transmission bandwidth is very limited. In this study, we propose a method to optimize the two-state hot-wire anemometer transmission bandwidth. The method is based on the use of a specialized constanttemperature system together with variable dynamic parameters. It is also based on a suitable measurement cycle paradigm. Analysis of the method was undertaken using model testing. Our results reveal a possible significant broadening of the two-state hot-wire anemometer's transmission bandwidth.

  12. All-optical bandwidth-tailorable radar

    CERN Document Server

    Zou, Weiwen; Long, Xin; Zhang, Siteng; Cui, Yuanjun; Chen, Jianping

    2015-01-01

    Radar has been widely used in military, security, and rescue. Metamaterial cloak is employed in stealth targets to evade radar detection. Hence modern radar should be reconfigurable at multi-bands for detecting stealth targets, which might be realized based on microwave photonics. Here, we demonstrate an all-optical bandwidth-tailorable radar architecture. It is a coherent system utilizing one mode-locked laser for both signal generation and reception. Heterodyning of two individually filtered optical pulses that are pre-chirped via wavelength-to-time mapping generates wideband linearly-chirped radar signal. The working bands can be flexibly tailored with desired bandwidth at user-preferred carrier frequency. After modulated onto the pre-chirped optical pulse, radar echoes are time-stretched and frequency-compressed by several times. The digitization becomes much easier without loss of detection ability. We believe that the demonstration can innovate the radar's architecture with ultra-high range resolution.

  13. Black holes, bandwidths and Beethoven

    Science.gov (United States)

    Kempf, Achim

    2000-04-01

    It is usually believed that a function φ(t) whose Fourier spectrum is bounded can vary at most as fast as its highest frequency component ωmax. This is, in fact, not the case, as Aharonov, Berry, and others drastically demonstrated with explicit counterexamples, so-called superoscillations. It has been claimed that even the recording of an entire Beethoven symphony can occur as part of a signal with a 1 Hz bandwidth. Bandlimited functions also occur as ultraviolet regularized fields. Their superoscillations have been suggested, for example, to resolve the trans-Planckian frequencies problem of black hole radiation. Here, we give an exact proof for generic superoscillations. Namely, we show that for every fixed bandwidth there exist functions that pass through any finite number of arbitrarily prespecified points. Further, we show that, in spite of the presence of superoscillations, the behavior of bandlimited functions can be characterized reliably, namely through an uncertainty relation: The standard deviation ΔT of samples φ(tn) taken at the Nyquist rate obeys ΔT>=1/4ωmax. This uncertainty relation generalizes to variable bandwidths. For ultraviolet regularized fields we identify the bandwidth as the in general spatially variable finite local density of degrees of freedom.

  14. Tunable-Bandwidth Filter System

    Science.gov (United States)

    Aye, Tin; Yu, Kevin; Dimov, Fedor; Savant, Gajendra

    2006-01-01

    A tunable-bandwidth filter system (TBFS), now undergoing development, is intended to be part of a remote-sensing multispectral imaging system that will operate in the visible and near infrared spectral region (wavelengths from 400 to 900 nm). Attributes of the TBFS include rapid tunability of the pass band over a wide wavelength range and high transmission efficiency. The TBFS is based on a unique integration of two pairs of broadband Raman reflection holographic filters with two rotating spherical lenses. In experiments, a prototype of the TBFS was shown to be capable of spectral sampling of images in the visible range over a 200-nm spectral range with a spectral resolution of .30 nm. The figure depicts the optical layout of a prototype of the TBFS as part of a laboratory multispectral imaging system for the spectral sampling of color test images in two orthogonal polarizations. Each pair of broadband Raman reflection holographic filters is mounted at an equatorial plane between two halves of a spherical lens. The two filters in each pair are characterized by steep spectral slopes (equivalently, narrow spectral edges), no ripple or side lobes in their pass bands, and a few nanometers of non-overlapping wavelength range between their pass bands. Each spherical lens and thus the filter pair within it is rotated in order to rapidly tune its pass band. The rotations of the lenses are effected by electronically controlled, programmable, high-precision rotation stages. The rotations are coordinated by electronic circuits operating under overall supervision of a personal computer in order to obtain the desired variation of the overall pass bands with time. Embedding the filters inside the spherical lenses increases the range of the hologram incidence angles, making it possible to continuously tune the pass and stop bands of the filters over a wider wavelength range. In addition, each spherical lens also serves as part of the imaging optics: The telephoto lens focuses

  15. Frequency response and bandwidth enhancement in Ge/Si avalanche photodiodes with over 840 GHz gain-bandwidth-product.

    Science.gov (United States)

    Zaoui, Wissem Sfar; Chen, Hui-Wen; Bowers, John E; Kang, Yimin; Morse, Mike; Paniccia, Mario J; Pauchard, Alexandre; Campbell, Joe C

    2009-07-20

    In this work we report a separate-absorption-charge-multiplication Ge/Si avalanche photodiode with an enhanced gain-bandwidth-product of 845 GHz at a wavelength of 1310 nm. The corresponding gain value is 65 and the electrical bandwidth is 13 GHz at an optical input power of -30 dBm. The unconventional high gain-bandwidth-product is investigated using device physical simulation and optical pulse response measurement. The analysis of the electric field distribution, electron and hole concentration and drift velocities in the device shows that the enhanced gain-bandwidth-product at high bias voltages is due to a decrease of the transit time and avalanche build-up time limitation at high fields.

  16. Black Holes, Bandwidths and Beethoven

    OpenAIRE

    Kempf, A.

    1999-01-01

    It is usually believed that a function whose Fourier spectrum is bounded can vary at most as fast as its highest frequency component. This is in fact not the case, as Aharonov, Berry and others drastically demonstrated with explicit counter examples, so-called superoscillations. It has been claimed that even the recording of an entire Beethoven symphony can occur as part of a signal with 1Hz bandwidth. Bandlimited functions also occur as ultraviolet regularized fields. Their superoscillations...

  17. Utility-based bandwidth allocation algorithm for heterogeneous wireless networks

    Institute of Scientific and Technical Information of China (English)

    CHAI Rong; WANG XiuJuan; CHEN QianBin; SVENSSON Tommy

    2013-01-01

    In next generation wireless network (NGWN), mobile users are capable of connecting to the core network through various heterogeneous wireless access networks, such as cellular network, wireless metropolitan area network (WMAN), wireless local area network (WLAN), and ad hoc network. NGWN is expected to provide high-bandwidth connectivity with guaranteed quality-of-service to mobile users in a seamless manner; however, this desired function demands seamless coordination of the heterogeneous radio access network (RAN) technologies. In recent years, some researches have been conducted to design radio resource management (RRM) architectures and algorithms for NGWN; however, few studies stress the problem of joint network performance optimization, which is an essential goal for a cooperative service providing scenario. Furthermore, while some authors consider the competition among the service providers, the QoS requirements of users and the resource competition within access networks are not fully considered. In this paper, we present an interworking integrated network architecture, which is responsible for monitoring the status information of different radio access technologies (RATs) and executing the resource allocation algorithm. Within this architecture, the problem of joint bandwidth allocation for heterogeneous integrated networks is formulated based on utility function theory and bankruptcy game theory. The proposed bandwidth allocation scheme comprises two successive stages, i.e., service bandwidth allocation and user bandwidth allocation. At the service bandwidth allocation stage, the optimal amount of bandwidth for different types of services in each network is allocated based on the criterion of joint utility maximization. At the user bandwidth allocation stage, the service bandwidth in each network is optimally allocated among users in the network according to bankruptcy game theory. Numerical results demonstrate the efficiency of

  18. Challenges in Polybinary Modulation for Bandwidth Limited Optical Links

    DEFF Research Database (Denmark)

    Vegas Olmos, Juan José; Tafur Monroy, Idelfonso; Madsen, Peter

    2016-01-01

    Optical links using traditional modulation formats are reaching a plateau in terms of capacity, mainly due to bandwidth limitations in the devices employed at the transmitter and receivers. Advanced modulation formats, which boost the spectral efficiency, provide a smooth migration path towards...... of the current research status of the key building blocks in polybinary systems. The results clearly show how polybinary modulation effectively reduces the bandwidth requirements on optical links while providing high spectral efficiency....

  19. Improving the Bandwidth Selection in Kernel Equating

    Science.gov (United States)

    Andersson, Björn; von Davier, Alina A.

    2014-01-01

    We investigate the current bandwidth selection methods in kernel equating and propose a method based on Silverman's rule of thumb for selecting the bandwidth parameters. In kernel equating, the bandwidth parameters have previously been obtained by minimizing a penalty function. This minimization process has been criticized by practitioners…

  20. 47 CFR 2.202 - Bandwidths.

    Science.gov (United States)

    2010-10-01

    ... RULES AND REGULATIONS Emissions § 2.202 Bandwidths. (a) Occupied bandwidth. The frequency bandwidth such.... Facsimile Analogue facsimile by sub-carrier frequency modulation of a single-sideband emission with reduced...: 1980 Hz=1.98 kHz 1K98F3C 5. Composite Emissions (See Table III-B) Radio-relay system,...

  1. Dynamic bandwidth allocation in GPON networks

    DEFF Research Database (Denmark)

    Ozimkiewiez, J.; Ruepp, Sarah Renée; Dittmann, Lars

    2009-01-01

    Two Dynamic Bandwidth Allocation algorithms used for coordination of the available bandwidth between end users in a GPON network have been simulated using OPNET to determine and compare the performance, scalability and efficiency of status reporting and non status reporting dynamic bandwidth allo...

  2. Characterization of Mn-modified Pb(Mg(13)Nb(23))O(3)-PbZrO(3)-PbTiO(3) single crystals for high power broad bandwidth transducers.

    Science.gov (United States)

    Zhang, Shujun; Lee, Sung-Min; Kim, Dong-Ho; Lee, Ho-Yong; Shrout, Thomas R

    2008-09-22

    The effect of MnO(2) addition on the dielectric and piezoelectric properties of 0.4Pb(Mg(13)Nb(23))O(3)-0.25PbZrO(3)-0.35PbTiO(3) single crystals was investigated. Analogous to acceptor doping in "hard" Pb(Zr,Ti)O(3) based polycrystalline materials, the Mn doped crystals exhibited enhanced mechanical Q ( approximately 1050) with low dielectric loss ( approximately 0.2%), while maintaining ultrahigh electromechanical coupling k(33)>90%, inherent in domain engineered single crystals. The effect of acceptor doping was also evident in the build-up of an internal bias (E(i) approximately 1.6 kVcm), shown by a horizontal offset in the polarization-field behavior. Together with the relatively high usage temperature (T(R-T) approximately 140 degrees C), the Mn doped crystals are promising candidates for high power and broad bandwidth transducers.

  3. Improvement of CBQ for bandwidth reclamation of RPR

    Science.gov (United States)

    Huang, Benxiong; Wang, Xiaoling; Xu, Ming; Shi, Lili

    2004-04-01

    The Resilient Packet Ring (RPR) IEEE 802.17 standard is under development as a new high-speed backbone technology for metropolitan area networks (MAN) [1]. Bandwidth reclamation has been concerned in RPR specifications from draft 0.1 to draft 2.4. According to specifications, allocated bandwidth can be reused, or reclaimed, by a lower priority service class whenever the reclamation does not effect the service guarantees of any equal or higher priority classes on the local station or on any other station on the ring [2]. The class-based queuing (CBQ) algorithm is proposed to implement link-sharing [3]. A hierarchical link-sharing structure can be used to specify guidelines for the distribution of 'excess" bandwidth [4] and it can rate-limit all classes to their allocated bandwidth. There is some sameness between the link-sharing of CBQ and bandwidth reclamation of RPR. The CBQ is a mature technology while RPR is a new technology. Given CBQ improvement and full use so as to make its thought suitable for bandwidth reclamation of RPR is the focus of our work. In this paper, we present the solution that can solve the reclamation problem, which proves to be effective by simulation.

  4. Ptychography with broad-bandwidth radiation

    Energy Technology Data Exchange (ETDEWEB)

    Enders, B., E-mail: bjoern.enders@ph.tum.de; Dierolf, M.; Stockmar, M.; Pfeiffer, F. [Lehrstuhl für Biomedizinische Physik, Physik-Department and Institut für Medizintechnik, Technische Universität München, 85747 Garching (Germany); Cloetens, P. [European Synchrotron Radiation Facility, 38043 Grenoble (France); Thibault, P. [Department of Physics and Astronomy, University College London, London (United Kingdom)

    2014-04-28

    Ptychography, a scanning Coherent Diffractive Imaging (CDI) technique, has quickly gained momentum as a robust method to deliver quantitative images of extended specimens. A current conundrum for the development of X-ray CDI is the conflict between a need for higher flux to reach higher resolutions and the requirement to strongly filter the incident beam to satisfy the tight coherence prerequisite of the technique. Latest developments in algorithmic treatment of ptychographic data indicate that the technique is more robust than initially assumed, so that some experimental limitations can be substantially relaxed. Here, we demonstrate that ptychography can be conducted in conditions that were up to now considered insufficient, using a broad-bandwidth X-ray beam and an integrating scintillator-based detector. Our work shows the wide applicability of ptychography and paves the way to high-throughput, high-flux diffractive imaging.

  5. Controlling Laser Plasma Instabilities Using Temporal Bandwidth

    Science.gov (United States)

    Tsung, Frank; Weaver, J.; Lehmberg, R.

    2016-10-01

    We are performing particle-in-cell simulations using the code OSIRIS to study the effects of laser plasma interactions in the presence of temporal bandwidth under conditions relevant to current and future experiments on the NIKE laser. Our simulations show that, for sufficiently large bandwidth (where the inverse bandwidth is comparable with the linear growth time), the saturation level, and the distribution of hot electrons, can be effected by the addition of temporal bandwidths (which can be accomplished in experiments using beam smoothing techniques such as ISI). We will quantify these effects and investigate higher dimensional effects such as laser speckles. This work is supported by DOE and NRL.

  6. A low-noise, high-bandwidth magnetically-levitated momentum-wheel for 3-axis attitude control from a single wheel

    OpenAIRE

    Seddon, Jon; Pechev, Alexandre

    2009-01-01

    This paper proposes a new concept for attitude actuation for small satellites that uses active magnetic bearings to support and tilt a spinning rotor to provide 3-axis attitude control of the satellite using a single actuator. A controlled 3D motion in the spinning rotor provides a conventional torque output about the momentum axis and a gyroscopic torque output about any direction in the plane normal to the spinning axis. Therefore, a single tilting momentum-wheel can generate torque along t...

  7. An Array Consisting of 10 High-Speed Side-Illuminated Evanescently Coupled Waveguide Photodetectors Each with a Bandwidth of 20 GHz

    Science.gov (United States)

    Lv, Qian-Qian; Ye, Han; Yin, Dong-Dong; Yang, Xiao-Hong; Han, Qin

    2015-12-01

    Not Available Supported by the High-Tech Research and Development Program of China under Grant Nos 2013AA031401, 2015AA016902 and 2015AA016904, the National Natural Science Foundation of China under Grant Nos 61176053, 61274069 and 61435002, and the National Basic Research Program of China under Grant No 2012CB933503.

  8. Improving the Bandwidth Utilization by Recycling the Unused Bandwidth in IEEE 802.16 Networks

    Directory of Open Access Journals (Sweden)

    Gowri T

    2012-03-01

    Full Text Available The Physical and MAC layers have been specified in IEEE 802.16 networks. The quality of service is ensured by the bandwidth reservation. The subscriber station should reserve the bandwidth more than its demand. But the bandwidth is fully utilized by SS but not all the time. So the bandwidth has recycled by the process of recycling the unused bandwidth. The main objective of the proposed scheme is to utilize the unused bandwidth by recycling and maintain the QOS service. By recycling the throughput can be improved which maintains the QOS in the proposed scheme. During this recycling process to maintain the QOS services, the amount of reserved bandwidth is not changed. The proposed scheme can utilize the unused bandwidth up to 70% on average. Protocols and the scheduling algorithms are used to improve the utilization and throughput.

  9. High-bandwidth AFM-based rheology is a sensitive indicator of early cartilage aggrecan degradation relevant to mouse models of osteoarthritis.

    Science.gov (United States)

    Nia, Hadi T; Gauci, Stephanie J; Azadi, Mojtaba; Hung, Han-Hwa; Frank, Eliot; Fosang, Amanda J; Ortiz, Christine; Grodzinsky, Alan J

    2015-01-02

    Murine models of osteoarthritis (OA) and post-traumatic OA have been widely used to study the development and progression of these diseases using genetically engineered mouse strains along with surgical or biochemical interventions. However, due to the small size and thickness of murine cartilage, the relationship between mechanical properties, molecular structure and cartilage composition has not been well studied. We adapted a recently developed AFM-based nano-rheology system to probe the dynamic nanomechanical properties of murine cartilage over a wide frequency range of 1 Hz to 10 kHz, and studied the role of glycosaminoglycan (GAG) on the dynamic modulus and poroelastic properties of murine femoral cartilage. We showed that poroelastic properties, highlighting fluid-solid interactions, are more sensitive indicators of loss of mechanical function compared to equilibrium properties in which fluid flow is negligible. These fluid-flow-dependent properties include the hydraulic permeability (an indicator of the resistance of matrix to fluid flow) and the high frequency modulus, obtained at high rates of loading relevant to jumping and impact injury in vivo. Utilizing a fibril-reinforced finite element model, we estimated the poroelastic properties of mouse cartilage over a wide range of loading rates for the first time, and show that the hydraulic permeability increased by a factor ~16 from knormal=7.80×10(-16)±1.3×10(-16) m(4)/N s to kGAG-depleted=1.26×10(-14)±6.73×10(-15) m(4)/N s after GAG depletion. The high-frequency modulus, which is related to fluid pressurization and the fibrillar network, decreased significantly after GAG depletion. In contrast, the equilibrium modulus, which is fluid-flow independent, did not show a statistically significant alteration following GAG depletion. Copyright © 2014 Elsevier Ltd. All rights reserved.

  10. Highly sensitive wide bandwidth photodetector based on internal photoemission in CVD grown p-type MoS2/graphene Schottky junction.

    Science.gov (United States)

    Vabbina, PhaniKiran; Choudhary, Nitin; Chowdhury, Al-Amin; Sinha, Raju; Karabiyik, Mustafa; Das, Santanu; Choi, Wonbong; Pala, Nezih

    2015-07-22

    Two dimensional (2D) Molybdenum disulfide (MoS2) has evolved as a promising material for next generation optoelectronic devices owing to its unique electrical and optical properties, such as band gap modulation, high optical absorption, and increased luminescence quantum yield. The 2D MoS2 photodetectors reported in the literature have presented low responsivity compared to silicon based photodetectors. In this study, we assembled atomically thin p-type MoS2 with graphene to form a MoS2/graphene Schottky photodetector where photo generated holes travel from graphene to MoS2 over the Schottky barrier under illumination. We found that the p-type MoS2 forms a Schottky junction with graphene with a barrier height of 139 meV, which results in high photocurrent and wide spectral range of detection with wavelength selectivity. The fabricated photodetector showed excellent photosensitivity with a maximum photo responsivity of 1.26 AW(-1) and a noise equivalent power of 7.8 × 10(-12) W/√Hz at 1440 nm.

  11. A Novel Dynamic Bandwidth Assignment Algorithm for Multi-Services EPONs

    Institute of Scientific and Technical Information of China (English)

    CHEN Xue; ZHANG Yang; HUANG Xiang; DENG Yu; SUN Shu-he

    2005-01-01

    In this paper we propose a novel Dynamic Bandwidth Assignment (DBA) algorithm for Ethernet-based Passive Optical Networks (EPON) which offers multiple kinds of services. To satisfy crucial Quality of Service (QoS) requirement for Time Division Multiplexing (TDM) service and achieve fair and high bandwidth utilization simultaneously, the algorithm integrates periodic, for TDM service, and polling granting for Ethernet service. Detailed simulation shows that the algorithm guarantees carrier-grade QoS for TDM service, high bandwidth utilization and good fairness of bandwidth assignment among Optical Network Units (ONU).

  12. Directing Traffic: Managing Internet Bandwidth Fairly

    Science.gov (United States)

    Paine, Thomas A.; Griggs, Tyler J.

    2008-01-01

    Educational institutions today face budgetary restraints and scarce resources, complicating the decision of how to allot bandwidth for campus network users. Additionally, campus concerns over peer-to-peer networking (specifically outbound Internet traffic) have increased because of bandwidth and copyright issues. In this article, the authors…

  13. 47 CFR 95.633 - Emission bandwidth.

    Science.gov (United States)

    2010-10-01

    ... SERVICES Technical Regulations Technical Standards § 95.633 Emission bandwidth. (a) The authorized... frequencies 151.820 MHz, 151.880 MHz, and 151.940 MHz are limited to 11.25 kHz. (2) Emissions on frequencies... 47 Telecommunication 5 2010-10-01 2010-10-01 false Emission bandwidth. 95.633 Section...

  14. Energy Bandwidth for Petroleum Refining Processes

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2006-10-01

    The petroleum refining energy bandwidth report analyzes the most energy-intensive unit operations used in U.S. refineries: crude oil distillation, fluid catalytic cracking, catalytic hydrotreating, catalytic reforming, and alkylation. The "bandwidth" provides a snapshot of the energy losses that can potentially be recovered through best practices and technology R&D.

  15. Bandwidth engineering of photonic crystal waveguide bends

    DEFF Research Database (Denmark)

    Borel, Peter Ingo; Frandsen, Lars Hagedorn; Harpøth, Anders;

    2004-01-01

    An effective design principle has been applied to photonic crystal waveguide bends fabricated in silicon-on-insulator material using deep UV lithography resulting in a large increase in the low-loss bandwidth of the bends. Furthermore, it is experimentally demonstrated that the absolute bandwidth...

  16. A System Theoretic Approach to Bandwidth Estimation

    OpenAIRE

    Liebeherr, Jorg; Fidler, Markus; Valaee, Shahrokh

    2008-01-01

    It is shown that bandwidth estimation in packet networks can be viewed in terms of min-plus linear system theory. The available bandwidth of a link or complete path is expressed in terms of a {\\em service curve}, which is a function that appears in the network calculus to express the service available to a traffic flow. The service curve is estimated based on measurements of a sequence of probing packets or passive measurements of a sample path of arrivals. It is shown that existing bandwidth...

  17. Average Bandwidth Allocation Model of WFQ

    Directory of Open Access Journals (Sweden)

    Tomáš Balogh

    2012-01-01

    Full Text Available We present a new iterative method for the calculation of average bandwidth assignment to traffic flows using a WFQ scheduler in IP based NGN networks. The bandwidth assignment calculation is based on the link speed, assigned weights, arrival rate, and average packet length or input rate of the traffic flows. We prove the model outcome with examples and simulation results using NS2 simulator.

  18. Investigation of Diagonal Antenna-Chassis Mode in Mobile Terminal LTE MIMO Antennas for Bandwidth Enhancement

    DEFF Research Database (Denmark)

    Zhang, Shuai; Zhao, Kun; Ying, Zhinong

    2015-01-01

    A diagonal antenna-chassis mode is investigated in long-term evolution multiple-input-multiple-output (LTE MIMO) antennas. The MIMO bandwidth is defined in this paper as the overlap range of the low-envelope correlation coefficient, high total efficiency, and -6-dB impedance matching bandwidths...

  19. Schottky Heterodyne Receivers With Full Waveguide Bandwidth

    Science.gov (United States)

    Hesler, Jeffrey; Crowe, Thomas

    2011-01-01

    Compact THz receivers with broad bandwidth and low noise have been developed for the frequency range from 100 GHz to 1 THz. These receivers meet the requirements for high-resolution spectroscopic studies of planetary atmospheres (including the Earth s) from spacecraft, as well as airborne and balloon platforms. The ongoing research is significant not only for the development of Schottky mixers, but also for the creation of a receiver system, including the LO chain. The new receivers meet the goals of high sensitivity, compact size, low total power requirement, and operation across complete waveguide bands. The exceptional performance makes these receivers ideal for the broader range of scientific and commercial applications. These include the extension of sophisticated test and measurement equipment to 1 THz and the development of low-cost imaging systems for security applications and industrial process monitoring. As a particular example, a WR-1.9SHM (400-600 GHz) has been developed (see Figure 1), with state-of-the-art noise temperature ranging from 1,000-1,800 K (DSB) over the full waveguide band. Also, a Vector Network Analyzer extender has been developed (see Figure 2) for the WR1.5 waveguide band (500 750 GHz) with 100-dB dynamic range.

  20. Recent Approaches for Broadening the Spectral Bandwidth in Resonant Cavity Optoelectronic Devices

    Directory of Open Access Journals (Sweden)

    Gun Wu Ju

    2015-01-01

    Full Text Available Resonant cavity optoelectronic devices, such as vertical cavity surface emitting lasers (VCSELs, resonant cavity enhanced photodetectors (RCEPDs, and electroabsorption modulators (EAMs, show improved performance over their predecessors by placing the active device structure inside a resonant cavity. The effect of the optical cavity, which allows wavelength selectivity and enhancement of the optical field due to resonance, allows the devices to be made thinner and therefore faster, while simultaneously increasing the quantum efficiency at the resonant wavelengths. However, the narrow spectral bandwidth significantly reduces operating tolerances, which leads to severe problems in applications such as optical communication, imaging, and biosensing. Recently, in order to overcome such drawbacks and/or to accomplish multiple functionalities, several approaches for broadening the spectral bandwidth in resonant cavity optoelectronic devices have been extensively studied. This paper reviews the recent progress in techniques for wide spectral bandwidth that include a coupled microcavity, asymmetric tandem quantum wells, and high index contrast distributed Bragg-reflectors. This review will describe design guidelines for specific devices together with experimental considerations in practical applications.

  1. Optimization of Single-Sensor Two-State Hot-Wire Anemometer Transmission Bandwidth

    Directory of Open Access Journals (Sweden)

    Paweł Ligęza

    2008-10-01

    Full Text Available Hot-wire anemometric measurements of non-isothermal flows require the use of thermal compensation or correction circuitry. One possible solution is a two-state hot-wire anemometer that uses the cyclically changing heating level of a single sensor. The area in which flow velocity and fluid temperature can be measured is limited by the dimensions of the sensor’s active element. The system is designed to measure flows characterized by high velocity and temperature gradients, although its transmission bandwidth is very limited. In this study, we propose a method to optimize the two-state hot-wire anemometer transmission bandwidth. The method is based on the use of a specialized constanttemperature system together with variable dynamic parameters. It is also based on a suitable measurement cycle paradigm. Analysis of the method was undertaken using model testing. Our results reveal a possible significant broadening of the two-state hot-wire anemometer's transmission bandwidth.

  2. Bandwidth utilization maximization of scientific RF communication systems

    Energy Technology Data Exchange (ETDEWEB)

    Rey, D. [Sandia National Lab., Albuquerque, NM (United States); Ryan, W. [New Mexico State Univ., Las Cruces, NM (United States); Ross, M.

    1997-01-01

    A method for more efficiently utilizing the frequency bandwidth allocated for data transmission is presented. Current space and range communication systems use modulation and coding schemes that transmit 0.5 to 1.0 bits per second per Hertz of radio frequency bandwidth. The goal in this LDRD project is to increase the bandwidth utilization by employing advanced digital communications techniques. This is done with little or no increase in the transmit power which is usually very limited on airborne systems. Teaming with New Mexico State University, an implementation of trellis coded modulation (TCM), a coding and modulation scheme pioneered by Ungerboeck, was developed for this application and simulated on a computer. TCM provides a means for reliably transmitting data while simultaneously increasing bandwidth efficiency. The penalty is increased receiver complexity. In particular, the trellis decoder requires high-speed, application-specific digital signal processing (DSP) chips. A system solution based on the QualComm Viterbi decoder and the Graychip DSP receiver chips is presented.

  3. 未来高带宽网络中FAST TCP与TCP Vegas的公平性分析%Fairness analysis of FAST TCP and TCP Vegas over future high-bandwidth internet

    Institute of Scientific and Technical Information of China (English)

    朱小松

    2012-01-01

    FAST TCP, a modern end-to-end protocol adopting queuing delay as a congestion measure. However, the lack of a precise measurement of queuing delay leads to a potential unfairness problem that FAST TCP flows may be discriminated against according to their starting times in a persistent congestion scenario, TCP Vegas also encounters the unfairness problem. The unfairness problem is quantitatively assessed by mathematical analysis and ns2 simulations, then, we compared FAST TCP with TCP Vegas. Consequently, FAST TCP demonstrates a competitive edge over TCP Vegas, under future high bandwidth-delay product environment. This conclusion will contribute to the improvement of FAST TCP for future reference.%FAST TCP是先进的端到端拥塞控制协议,采用队列时延作为拥塞度量.由于不能准确测得精确的队列时延,此协议中存有不公平的隐患,即在某些持续拥塞场景下,不同时刻启动的FAST TCP流会受到差别对待,TCP Vegas中同样存在不公平问题.通过数学分析和ns2仿真对这种不公平问题进行量化,进而比较FASTTCP与TCP Vegas在公平性问题上的性能差异.结果证明了在将来高带宽时延乘积网络环境下,FAST TCP在公平性上要明显优于TCP Vegas.这为对FAST TCP协议的改进给出了有价值的参照.

  4. Passive Mobile Bandwidth Classification Using Short Lived TCP Connections

    OpenAIRE

    Michelinakis, Foivos; Kreitz, Gunnar; Petrocco, Riccardo; Zhang, Boxun; Widmer, Joerg

    2015-01-01

    Consumption of multimedia content is moving from a residential environment to mobile phones. Optimizing Quality of Experience—smooth, quick, and high quality playback—is more difficult in this setting, due to the highly dynamic nature of wireless links. A key requirement for achieving this goal is estimating the available bandwidth of mobile devices. Ideally, this should be done quickly and with low overhead. One challenge is that the majority of connections on mobiles are short-l...

  5. Large scale probabilistic available bandwidth estimation

    CERN Document Server

    Thouin, Frederic; Rabbat, Michael

    2010-01-01

    The common utilization-based definition of available bandwidth and many of the existing tools to estimate it suffer from several important weaknesses: i) most tools report a point estimate of average available bandwidth over a measurement interval and do not provide a confidence interval; ii) the commonly adopted models used to relate the available bandwidth metric to the measured data are invalid in almost all practical scenarios; iii) existing tools do not scale well and are not suited to the task of multi-path estimation in large-scale networks; iv) almost all tools use ad-hoc techniques to address measurement noise; and v) tools do not provide enough flexibility in terms of accuracy, overhead, latency and reliability to adapt to the requirements of various applications. In this paper we propose a new definition for available bandwidth and a novel framework that addresses these issues. We define probabilistic available bandwidth (PAB) as the largest input rate at which we can send a traffic flow along a pa...

  6. Construction and experimental testing of the constant-bandwidth constant-temperature anemometer.

    Science.gov (United States)

    Ligeza, P

    2008-09-01

    A classical constant-temperature hot-wire anemometer enables the measurement of fast-changing flow velocity fluctuations, although its transmission bandwidth is a function of measured velocity. This may be a source of significant dynamic errors. Incorporation of an adaptive controller into the constant-temperature system results in hot-wire anemometer operating with a constant transmission bandwidth. The construction together with the results of experimental testing of a constant-bandwidth hot-wire anemometer prototype are presented in this article. During the testing, an approximately constant transmission bandwidth of the anemometer was achieved. The constant-bandwidth hot-wire anemometer can be used in measurements of high-frequency variable flows characterized by a wide range of velocity changes.

  7. Reconstruction in Time-Bandwidth Compression Systems

    CERN Document Server

    Chan, Jacky; Asghari, Mohammad H; Jalali, Bahram

    2014-01-01

    Recently it has been shown that the intensity time-bandwidth product of optical signals can be engineered to match that of the data acquisition instrument. In particular, it is possible to slow down an ultrafast signal, resulting in compressed RF bandwidth - a similar benefit to that offered by the Time-Stretch Dispersive Fourier Transform (TS-DFT) - but with reduced temporal record length leading to time-bandwidth compression. The compression is implemented using a warped group delay dispersion leading to non-uniform time stretching of the signal's intensity envelope. Decoding requires optical phase retrieval and reconstruction of the input temporal profile, for the case where information of interest is resides in the complex field. In this paper, we present results on the general behavior of the reconstruction process and its dependence on the signal-to-noise ratio. We also discuss the role of chirp in the input signal.

  8. Large-bandwidth planar photonic crystal waveguides

    DEFF Research Database (Denmark)

    Søndergaard, Thomas; Lavrinenko, Andrei

    2002-01-01

    A general design principle is presented for making finite-height photonic crystal waveguides that support leakage-free guidance of light over large frequency intervals. The large bandwidth waveguides are designed by introducing line defects in photonic crystal slabs, where the material in the lin......-free single-mode guidance is found for a large frequency interval covering 60% of the photonic band-gap.......A general design principle is presented for making finite-height photonic crystal waveguides that support leakage-free guidance of light over large frequency intervals. The large bandwidth waveguides are designed by introducing line defects in photonic crystal slabs, where the material in the line...... defect has appropriate dispersion properties relative to the photonic crystal slab material surrounding the line defect. A three-dimensional theoretical analysis is given for large-bandwidth waveguide designs based on a silicon-air photonic crystal slab suspended in air. In one example, the leakage...

  9. Bandwidth Assessment for MultiRotor UAVs

    Directory of Open Access Journals (Sweden)

    Ferrarese Gastone

    2017-06-01

    Full Text Available This paper is a technical note about the theoretical evaluation of the bandwidth of multirotor helicopters. Starting from a mathematical linear model of the dynamics of a multirotor aircraft, the transfer functions of the state variables that deeply affect the stability characteristics of the aircraft are obtained. From these transfer functions, the frequency response analysis of the system is effected. After this analysis, the bandwidth of the system is defined. This result is immediately utilized for the design of discrete PID controllers for hovering flight stabilization. Numeric simulations are shown to demonstrate that the knowledge of the bandwidth is a valid aid in the design of flight control systems of these machines.

  10. Improved space bandwidth product in image upconversion

    DEFF Research Database (Denmark)

    Dam, Jeppe Seidelin; Pedersen, Christian; Tidemand-Lichtenberg, Peter

    2012-01-01

    We present a technique increasing the space bandwidth product of a nonlinear image upconversion process used for spectral imaging. The technique exploits the strong dependency of the phase-matching condition in sum frequency generation (SFG) on the angle of propagation of the interacting fields...... with respect to the optical axis. Appropriate scanning of the phase-match condition (Δk=0) while acquiring images, allow us to perform monochromatic image reconstruction with a significantly increased space bandwidth product. We derive the theory for the image reconstruction process and demonstrate acquisition...... of images with >10 fold increase in space bandwidth product, i.e. the number of pixel elements, when compared to upconversion of images using fixed phase-match conditions....

  11. Long-pulse-width narrow-bandwidth solid state laser

    Science.gov (United States)

    Dane, C.B.; Hackel, L.A.

    1997-11-18

    A long pulse laser system emits 500-1000 ns quasi-rectangular pulses at 527 nm with near diffraction-limited divergence and near transform-limited bandwidth. The system consists of one or more flashlamp-pumped Nd:glass zig-zag amplifiers, a very low threshold stimulated-Brillouin-scattering (SBS) phase conjugator system, and a free-running single frequency Nd:YLF master oscillator. Completely passive polarization switching provides eight amplifier gain passes. Multiple frequency output can be generated by using SBS cells having different pressures of a gaseous SBS medium or different SBS materials. This long pulse, low divergence, narrow-bandwidth, multi-frequency output laser system is ideally suited for use as an illuminator for long range speckle imaging applications. Because of its high average power and high beam quality, this system has application in any process which would benefit from a long pulse format, including material processing and medical applications. 5 figs.

  12. Exploiting material softening in hard PZTs for resonant bandwidth enhancement

    Science.gov (United States)

    Leadenham, S.; Moura, A.; Erturk, A.

    2016-04-01

    Intentionally designed nonlinearities have been employed by several research groups to enhance the frequency bandwidth of vibration energy harvesters. Another type of nonlinear resonance behavior emerges from the piezoelectric constitutive behavior for high excitation levels and is manifested in the form of softening stiffness. This material nonlinearity does not result in the jump phenomenon in soft piezoelectric ceramics, e.g. PZT-5A and PZT-5H, due to their large internal dissipation. This paper explores the potential for wideband energy harvesting using a hard (relatively high quality factor) PZT-8 bimorph by exploiting its material softening. A wide range of base excitation experiments conducted for a set of resistive electrical loads confirms the frequency bandwidth enhancement.

  13. Large-bandwidth planar photonic crystal waveguides

    DEFF Research Database (Denmark)

    Søndergaard, Thomas; Lavrinenko, Andrei

    2002-01-01

    A general design principle is presented for making finite-height photonic crystal waveguides that support leakage-free guidance of light over large frequency intervals. The large bandwidth waveguides are designed by introducing line defects in photonic crystal slabs, where the material in the line...... defect has appropriate dispersion properties relative to the photonic crystal slab material surrounding the line defect. A three-dimensional theoretical analysis is given for large-bandwidth waveguide designs based on a silicon-air photonic crystal slab suspended in air. In one example, the leakage...

  14. High-Activity Dealloyed Catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Kongkanand, Anusorn [General Motors LLC, Pontiac, MI (United States)

    2014-09-30

    Reduction of costly Pt usage in proton exchange membrane fuel cell electrodes is one of the major challenges towards development and commercialization of fuel cell vehicles. Although few have met the initial-kinetic activity requirements in a realistic fuel cell device, no catalyst material has ever met the demanding fuel cell durability targets set by DOE. In this project, a team of 4 universities and 2 companies came together to investigate a concept that appeared promising in preliminary non-fuel cell tests then to further develop the catalyst to a mature level ready for vehicle implementation. The team consists of academia with technical leadership in their respective areas, a catalyst supplier, and a fuel cell system integrator.The tightly collaborative project enabled development of a highly active and durable catalyst with performance that significantly exceeds that of previous catalysts and meets the DOE targets for the first time (Figure 1A). The catalyst was then further evaluated in full-active-area stack in a realistic vehicle operating condition (Figure 1B). This is the first public demonstration that one can realize the performance benefit and Pt cost reduction over a conventional pure Pt catalyst in a long-term realistic PEMFC system. Furthermore, systematic analyses of a range of catalysts with different performance after fuel cell testing allowed for correlation between catalyst microstructure and its electrocatalytic activity and durability. This will in turn aid future catalyst development.

  15. 有源滤波器的模糊阈值变环宽滞环电流跟踪控制策略%A fuzzy threshold mutative bandwidth hysteresis current tracking control method for active power filter

    Institute of Scientific and Technical Information of China (English)

    刘心旸; 王杰; 王昕; 姚钢

    2011-01-01

    A fuzzy threshold mutative bandwidth hysteresis current tracking control method for the Active Power Filter (APF) current tracking module is presented. Based on the construction of APF device model and the analysis of the variation of hysteresis width, the purpose to achieve a limited frequency of switching is reached by using an internal fuzzy controller to dynamically adjust the loop width of hysteresis comparator device. Compared with the traditional hysteresis method, the proposed method has more excellent dynamic response and tracking precision, taking full advantage of conduction capability of the power switches, moreover,a reduction of the maximum switching frequency ensures that the device operates safely. Finally, the current tracking efficiency of the method above and the harmonic compensating capability to nonlinear loads are demonstrated by the simulation and experiment results in this paper.This work is supported by National Natural Science Foundation of China (No. 60674035).%针对有源电力滤波器(APF)的电流跟踪功能模块,提出了一种模糊阈值变环宽滞环电流跟踪控制算法.在构建APF装置模型并分析滞环宽度变化规律的基础上,通过使用内部模糊控制器用以动态地调节滞环比较器的环宽,从而达到了限定开关频率的目的.该方法相比于传统滞环比较方法具有更好的跟踪精度和动态性能,充分利用了开关器件的导通能力;同时由于降低了最大开关频率,从而保证了装置的安全运行.通过仿真与实际实验结果进一步验证了该算法的电流跟踪效果以及对于非线性装置产生的系统谐波的补偿能力.

  16. Real-Time Virtual Instruments for Remote Sensor Monitoring Using Low Bandwidth Wireless Networks

    Directory of Open Access Journals (Sweden)

    Biruk Gebre

    2008-06-01

    Full Text Available The development of a peer-to-peer virtual instrumentation system for remote acquisition, analysis and transmission of data on low bandwidth networks is described. The objective of this system is to collect high frequency/high bandwidth data from multiple sensors placed at remote locations and adaptively adjust the resolution of this data so that it can be transmitted on bandwidth limited networks to a central monitoring and command center. This is achieved by adaptively re-sampling (decimating the data from the sensors at the remote location before transmission. The decimation is adjusted to the available bandwidth of the communications network which is characterized in real-time. As a result, the system allows users at the remote command center to view high bandwidth data (at a lower resolution with user-aware and minimized latency. This technique is applied to an eight hydrophone data acquisition system that requires a 25.6 Mbps connection for the transmission of the full data set using a wireless connection with 1 – 3.5 Mbps variable bandwidth. This technique can be used for applications that require monitoring of high bandwidth data from remote sensors in research and education fields such as remote scientific instruments and visually driven control applications.

  17. Real-Time Virtual Instruments for Remote Sensor Monitoring Using Low Bandwidth Wireless Networks

    Directory of Open Access Journals (Sweden)

    Biruk Gebre

    2008-06-01

    Full Text Available The development of a peer-to-peer virtual instrumentation system for remote acquisition, analysis and transmission of data on low bandwidth networks is described. The objective of this system is to collect high frequency/high bandwidth data from multiple sensors placed at remote locations and adaptively adjust the resolution of this data so that it can be transmitted on bandwidth limited networks to a central monitoring and command center. This is achieved by adaptively re-sampling (decimating the data from the sensors at the remote location before transmission. The decimation is adjusted to the available bandwidth of the communications network which is characterized in real-time. As a result, the system allows users at the remote command center to view high bandwidth data (at a lower resolution with user-aware and minimized latency. This technique is applied to an eight hydrophone data acquisition system that requires a 25.6 Mbps connection for the transmission of the full data set using a wireless connection with 1 – 3.5 Mbps variable bandwidth. This technique can be used for applications that require monitoring of high bandwidth data from remote sensors in research and education fields such as remote scientific instruments and visually driven control applications.

  18. Use of dominant harmonic active filters in high power applications

    Science.gov (United States)

    Cheng, Po-Tai

    The application of power electronics equipment is increasing rapidly. It is estimated that 60% of electrical power will be processed by power electronics equipment by year 2000. These equipments typically require rectifiers for AC-DC power conversion. Due to their nonlinear nature, most rectifiers draw harmonic current from the utility grid. The harmonic current causes higher energy losses, and may excite resonance conditions in the utility grid. Harmonic standards such as IEEE 519 and IEC 1000-3-2 have been proposed to regulate the harmonic current and voltage levels. This work is to develop a dominant harmonic active filter (DHAF) to realize a cost-effective active filtering solution for nonlinear loads in the range of megawatt and above. The DHAF system achieves harmonic isolation at dominant harmonic frequencies, e.g. the 5th and 7th. This approach allows use of low switching frequency and small rating active filter inverters (1%--2% of the load MVA rating) for implementation. Review of conventional passive filters and various active filters based on high bandwidth PWM inverters is provided. The control theory of the DHAF system is presented. Comparison of the DHAF system and other dominant harmonic filtering approach is provided. Simulation results and laboratory prototype test results are presented to validate the effectiveness of the proposed DHAF system.

  19. An Adaptive Bandwidth Allocation for Energy Efficient Wireless Communication Systems

    Institute of Scientific and Technical Information of China (English)

    Yung-Fa Huang,Che-Hao Li; Chuan-Bi Lin; Chia-Chi Chang

    2015-01-01

    Abstract―In this paper, an energy efficient bandwidth allocation scheme is proposed for wireless communication systems. An optimal bandwidth expansion (OBE) scheme is proposed to assign the available system bandwidth for users. When the system bandwidth does not reach the full load, the remaining bandwidth can be energy-efficiently assigned to the other users. Simulation results show that the energy efficiency of the proposed OBE scheme outperforms the traditional same bandwidth expansion (SBE) scheme. Thus, the proposed OBE can effectively assign the system bandwidth and improve energy efficiency.

  20. Coherent temporal imaging with analog time-bandwidth compression

    CERN Document Server

    Asghari, Mohammad H

    2013-01-01

    We introduce the concept of coherent temporal imaging and its combination with the anamorphic stretch transform. The new system can measure both temporal profile of fast waveforms as well as their spectrum in real time and at high-throughput. We show that the combination of coherent detection and warped time-frequency mapping also performs time-bandwidth compression. By reducing the temporal width without sacrificing spectral resolution, it addresses the Big Data problem in real time instruments. The proposed method is the first application of the recently demonstrated Anamorphic Stretch Transform to temporal imaging. Using this method narrow spectral features beyond the spectrometer resolution can be captured. At the same time the output bandwidth and hence the record length is minimized. Coherent detection allows the temporal imaging and dispersive Fourier transform systems to operate in the traditional far field as well as in near field regimes.

  1. Compact silicon multimode waveguide spectrometer with enhanced bandwidth

    Science.gov (United States)

    Piels, Molly; Zibar, Darko

    2017-01-01

    Compact, broadband, and high-resolution spectrometers are appealing for sensing applications, but difficult to fabricate. Here we show using calibration data a spectrometer based on a multimode waveguide with 2 GHz resolution, 250 GHz bandwidth, and a 1.6 mm × 2.1 mm footprint. Typically, such spectrometers have a bandwidth limited by the number of modes supported by the waveguide. In this case, an on-chip mode-exciting element is used to repeatably excite distinct collections of waveguide modes. This increases the number of independent spectral channels from the number of modes to this number squared, resulting in an extension of the usable range. PMID:28290537

  2. Dynamic resource management using bandwidth brokers

    Institute of Scientific and Technical Information of China (English)

    Yu Chengzhi; Song Hantao; Hou Xianjun; Pan Chengsheng

    2006-01-01

    The admission control issue in the design of a centralized bandwidth broker model for dynamic control and management of QoS provisioning is studied. A two-phase differentiated flow treatment based dynamic admission control scheme under the centralized bandwidth broker model is proposed. In the proposed scheme, the flow requests are classified into two classes and get differentiated treatment according to their QoS demands. We demonstrate that this admission control scheme can not only improve the resource utilization but also guarantee the flows' QoS. Furthermore, the admission control is divided into two phases: edge admission control and interior admissio-n control. During the interior phase, the PoQ scheme is adopted, which enhances the call processing capability of the bandwidth broker. The simulation results show that the proposed scheme can result in lower flow blocking probability and higher resource utilization. And it also reduces the number of QoS state accesses/updates, thereby increasing the overall call processing capability of the bandwidth broker.

  3. A System Theoretic Approach to Bandwidth Estimation

    CERN Document Server

    Liebeherr, Jorg; Valaee, Shahrokh

    2008-01-01

    It is shown that bandwidth estimation in packet networks can be viewed in terms of min-plus linear system theory. The available bandwidth of a link or complete path is expressed in terms of a {\\em service curve}, which is a function that appears in the network calculus to express the service available to a traffic flow. The service curve is estimated based on measurements of a sequence of probing packets or passive measurements of a sample path of arrivals. It is shown that existing bandwidth estimation methods can be derived in the min-plus algebra of the network calculus, thus providing further mathematical justification for these methods. Principal difficulties of estimating available bandwidth from measurement of network probes are related to potential non-linearities of the underlying network. When networks are viewed as systems that operate either in a linear or in a non-linear regime, it is argued that probing schemes extract the most information at a point when the network crosses from a linear to a n...

  4. Adaptive bandwidth measurements of importance functions for speech intelligibility prediction.

    Science.gov (United States)

    Whitmal, Nathaniel A; DeRoy, Kristina

    2011-12-01

    The Articulation Index (AI) and Speech Intelligibility Index (SII) predict intelligibility scores from measurements of speech and hearing parameters. One component in the prediction is the "importance function," a weighting function that characterizes contributions of particular spectral regions of speech to speech intelligibility. Previous work with SII predictions for hearing-impaired subjects suggests that prediction accuracy might improve if importance functions for individual subjects were available. Unfortunately, previous importance function measurements have required extensive intelligibility testing with groups of subjects, using speech processed by various fixed-bandwidth low-pass and high-pass filters. A more efficient approach appropriate to individual subjects is desired. The purpose of this study was to evaluate the feasibility of measuring importance functions for individual subjects with adaptive-bandwidth filters. In two experiments, ten subjects with normal-hearing listened to vowel-consonant-vowel (VCV) nonsense words processed by low-pass and high-pass filters whose bandwidths were varied adaptively to produce specified performance levels in accordance with the transformed up-down rules of Levitt [(1971). J. Acoust. Soc. Am. 49, 467-477]. Local linear psychometric functions were fit to resulting data and used to generate an importance function for VCV words. Results indicate that the adaptive method is reliable and efficient, and produces importance function data consistent with that of the corresponding AI/SII importance function.

  5. Kernel bandwidth estimation for non-parametric density estimation: a comparative study

    CSIR Research Space (South Africa)

    Van der Walt, CM

    2013-12-01

    Full Text Available We investigate the performance of conventional bandwidth estimators for non-parametric kernel density estimation on a number of representative pattern-recognition tasks, to gain a better understanding of the behaviour of these estimators in high...

  6. Improved Radiation and Bandwidth of Triangular and Star Patch Antenna

    Directory of Open Access Journals (Sweden)

    M. Ramkumar Prabhu

    2012-06-01

    Full Text Available This study presents a hexagonal shape Defected Ground Structure (DGS implemented on two element triangular patch microstrip antenna array. The radiation performance of the antenna is characterized by varying the geometry and dimension of the DGS and also by locating the DGS at specific position which were simulated. Simulation and measurement results have verified that the antenna with DGS had improved the antenna without DGS. Measurement results of the hexagonal DGS have axial ratio bandwidth enhancement of 10 MHz, return loss improvement of 35%, mutual coupling reduction of 3 dB and gain enhancement of 1 dB. A new wideband and small size star shaped patch antenna fed capacitively by a small diamond shape patch is proposed. To enhance the impedance bandwidth, posts are incorporated under the patch antenna. HFSS high frequency simulator is employed to analyze the proposed antenna and simulated results on the return loss, the E- and H-plane radiation patterns and Gain of the proposed antenna are presented at various frequencies. The antenna is able to achieve in the range of 4-8.8 GHz an impedance bandwidth of 81% for return loss of less than-10 dB.

  7. Optimization of Quantum-Dot Molecular Beam Epitaxy for Broad Spectral Bandwidth Devices

    KAUST Repository

    Majid, M. A.

    2012-12-01

    The optimization of the key growth parameters for broad spectral bandwidth devices based on quantum dots is reported. A combination of atomic force microscopy, photoluminescence of test samples, and optoelectronic characterization of superluminescent diodes (SLDs) is used to optimize the growth conditions to obtain high-quality devices with large spectral bandwidth, radiative efficiency (due to a reduced defective-dot density), and thus output power. The defective-dot density is highlighted as being responsible for the degradation of device performance. An SLD device with 160 nm of bandwidth centered at 1230 nm is demonstrated.

  8. Bandwidth-sharing in LHCONE, an analysis of the problem

    Science.gov (United States)

    Wildish, T.

    2015-12-01

    The LHC experiments have traditionally regarded the network as an unreliable resource, one which was expected to be a major source of errors and inefficiency at the time their original computing models were derived. Now, however, the network is seen as much more capable and reliable. Data are routinely transferred with high efficiency and low latency to wherever computing or storage resources are available to use or manage them. Although there was sufficient network bandwidth for the experiments’ needs during Run-1, they cannot rely on ever-increasing bandwidth as a solution to their data-transfer needs in the future. Sooner or later they need to consider the network as a finite resource that they interact with to manage their traffic, in much the same way as they manage their use of disk and CPU resources. There are several possible ways for the experiments to integrate management of the network in their software stacks, such as the use of virtual circuits with hard bandwidth guarantees or soft real-time flow-control, with somewhat less firm guarantees. Abstractly, these can all be considered as the users (the experiments, or groups of users within the experiment) expressing a request for a given bandwidth between two points for a given duration of time. The network fabric then grants some allocation to each user, dependent on the sum of all requests and the sum of available resources, and attempts to ensure the requirements are met (either deterministically or statistically). An unresolved question at this time is how to convert the users’ requests into an allocation. Simply put, how do we decide what fraction of a network's bandwidth to allocate to each user when the sum of requests exceeds the available bandwidth? The usual problems of any resourcescheduling system arise here, namely how to ensure the resource is used efficiently and fairly, while still satisfying the needs of the users. Simply fixing quotas on network paths for each user is likely to lead

  9. Available Bandwidth Estimation in Network-Aware Applications for Wireless Campus e-Learning System

    OpenAIRE

    Mohd Faisal Ibrahim; Masita Jamal; Saadiah Yahya; Mohd Nasir Taib

    2012-01-01

    The constraint of a wireless network has motivated many researchers to develop network-aware applications that can dynamically adjust the users' demand based on network resources. For this to happen, applications need to have some mechanism that can estimate the network bandwidth by simply adjusting their behavior based on the collected network characteristics information. In the past, there have been several proposals that provide passive and active bandwidth estimation approaches for wired ...

  10. BACH:A Bandwidth-Aware Hybrid Cache Hierarchy Design with Nonvolatile Memories

    Institute of Scientific and Technical Information of China (English)

    Jishen Zhao; Cong Xu; Tao Zhang; Yuan Xie

    2016-01-01

    Limited main memory bandwidth is becoming a fundamental performance bottleneck in chip-multiprocessor (CMP) design. Yet directly increasing the peak memory bandwidth can incur high cost and power consump-tion. In this paper, we address this problem by proposing a memory, a bandwidth-aware reconfigurable cache hierarchy, BACH, with hybrid memory technologies. Components of our BACH design include a hybrid cache hierarchy, a reconfigura-tion mechanism, and a statistical prediction engine. Our hybrid cache hierarchy chooses different memory technologies with various bandwidth characteristics, such as spin-transfer torque memory (STT-MRAM), resistive memory (ReRAM), and embedded DRAM (eDRAM), to configure each level so that the peak bandwidth of the overall cache hierarchy is optimized. Our reconfiguration mechanism can dynamically adjust the cache capacity of each level based on the predicted bandwidth demands of running workloads. The bandwidth prediction is performed by our prediction engine. We evaluate the system performance gain obtained by BACH design with a set of multithreaded and multiprogrammed workloads with and without the limitation of system power budget. Compared with traditional SRAM-based cache design, BACH improves the system throughput by 58%and 14%with multithreaded and multiprogrammed workloads respectively.

  11. 980-nm VCSELs for optical interconnects at bandwidths beyond 40 Gb/s

    Science.gov (United States)

    Hofmann, W. H.; Moser, P.; Wolf, P.; Larisch, G.; Unrau, W.; Bimberg, D.

    2012-03-01

    The copper-induced communication bottleneck is inhibiting performance and environmental acceptance of today's supercomputers. Vertical-cavity surface-emitting lasers (VCSELs) are ideally suited to solve this dilemma. Indeed global players like Google, Intel, HP or IBM are now going for optical interconnects based on VCSELs. The required bandwidth per link, however, is fixed by the architecture of the data center. According to Google, a bandwidth of 40 Gb/s has to be accommodated. We recently realized ultra-high speed VCSELs suited for optical interconnects in data centers with record-high performance. The 980-nm wavelength was chosen to be able to realize densely-packed, bottom-emitting devices particularly advantageous for interconnects. These devices show error-free transmission at temperatures up to 155°C. Serial data-rates of 40 Gb/s were achieved up to 75° C. Peltier-cooled devices were modulated up to 50 Gb/s. These results were achieved from the sender side by a VCSEL structure with important improvements and from the receiver side by a receiver module supplied by u2t with some 30 GHz bandwidth. The novel VCSELs feature a new active region, a very short laser cavity, and a drastically improved thermal resistance by the incorporation of a binary bottom mirror. As these devices might be of industrial interest we had the epi-growth done by metal-organic chemical-vapor deposition at IQE Europe. Consequently, the devices were fabricated using a three-inch wafer process, and the apertures were formed by proprietary in-situ controlled selective wet oxidation. All device data were measured, mapped and evaluated by our fully automated probe station. Furthermore, these devices enable record-efficient data-transmission beyond 30 Gb/s, which is crucial for green photonics.

  12. DBAS: A Deployable Bandwidth Aggregation System

    CERN Document Server

    Habak, Karim; Harras, Khaled A

    2012-01-01

    The explosive increase in data demand coupled with the rapid deployment of various wireless access technologies have led to the increase of number of multi-homed or multi-interface enabled devices. Fully exploiting these interfaces has motivated researchers to propose numerous solutions that aggregate their available bandwidths to increase overall throughput and satisfy the end-user's growing data demand. These solutions, however, have faced a steep deployment barrier that we attempt to overcome in this paper. We propose a Deployable Bandwidth Aggregation System (DBAS) for multi-interface enabled devices. Our system does not introduce any intermediate hardware, modify current operating systems, modify socket implementations, nor require changes to current applications or legacy servers. The DBAS architecture is designed to automatically estimate the characteristics of applications and dynamically schedule various connections or packets to different interfaces. Since our main focus is deployability, we fully i...

  13. Sensor fusion methods for high performance active vibration isolation systems

    Science.gov (United States)

    Collette, C.; Matichard, F.

    2015-04-01

    Sensor noise often limits the performance of active vibration isolation systems. Inertial sensors used in such systems can be selected through a wide variety of instrument noise and size characteristics. However, the most sensitive instruments are often the biggest and the heaviest. Consequently, high-performance active isolators sometimes embed many tens of kilograms in instrumentation. The weight and size of instrumentation can add unwanted constraint on the design. It tends to lower the structures natural frequencies and reduces the collocation between sensors and actuators. Both effects tend to reduce feedback control performance and stability. This paper discusses sensor fusion techniques that can be used in order to increase the control bandwidth (and/or the stability). For this, the low noise inertial instrument signal dominates the fusion at low frequency to provide vibration isolation. Other types of sensors (relative motion, smaller but noisier inertial, or force sensors) are used at higher frequencies to increase stability. Several sensor fusion configurations are studied. The paper shows the improvement that can be expected for several case studies including a rigid equipment, a flexible equipment, and a flexible equipment mounted on a flexible support structure.

  14. Digital demodulator for wide bandwidth SAR

    DEFF Research Database (Denmark)

    Jørgensen, Jørn Hjelm

    2000-01-01

    A novel approach to the design of efficient digital quadrature demodulators for wide bandwidth SAR systems is described. Efficiency is obtained by setting the intermediate frequency to 1/4 the ADC sampling frequency. One channel is made filter-free by synchronizing the local oscillator...... with the output decimator. The filter required by the other channel is optimized through global search using the system level performance metrics integrated sidelobe level ratio (ISLR) and peak sidelobe level ratio (PSLR)....

  15. A Novel Dynamic Bandwidth Allocation Algorithm with Correction-based the Multiple Traffic Prediction in EPON

    Directory of Open Access Journals (Sweden)

    Ziyi Fu

    2012-10-01

    Full Text Available According to the upstream TDM in the system of Ethernet passive optical network (EPON, this paper proposes a novel dynamic bandwidth allocation algorithm which supports the mechanism with correction-based the multiple services estimation. To improve the real-time performance of the bandwidth allocation, this algorithm forecasts the traffic of high priority services, and then pre-allocate bandwidth for various priority services is corrected according to Gaussian distribution characteristics, which will make traffic prediction closer to the real traffic. The simulation results show that proposed algorithm is better than the existing DBA algorithm. Not only can it meet the delay requirement of high priority services, but also control the delay abnormity of low priority services. In addition, with rectification scheme, it obviously improves the bandwidth utilization.

  16. A wide bandwidth analog front-end circuit for 60-GHz wireless communication receiver

    Science.gov (United States)

    Furuta, M.; Okuni, H.; Hosoya, M.; Sai, A.; Matsuno, J.; Saigusa, S.; Itakura, T.

    2014-03-01

    This paper presents an analog front-end circuit for a 60-GHz wireless communication receiver. The feature of the proposed analog front-end circuit is a bandwidth more than 1-GHz wide. To expand the bandwidth of a low-pass filter and a voltage gain amplifier, a technique to reduce the parasitic capacitance of a transconductance amplifier is proposed. Since the bandwidth is also limited by on-resistance of the ADC sampling switch, a switch separation technique for reduction of the on-resistance is also proposed. In a high-speed ADC, the SNDR is limited by the sampling jitter. The developed high resolution VCO auto tuning effectively reduces the jitter of PLL. The prototype is fabricated in 65nm CMOS. The analog front-end circuit achieves over 1-GHz bandwidth and 27.2-dB SNDR with 224 mW Power consumption.

  17. Gaussian entanglement distribution with GHz bandwidth

    CERN Document Server

    Ast, Stefan; Mehmet, Moritz; Schnabel, Roman

    2016-01-01

    The distribution of Gaussian entanglement can be used to generate a mathematically-proven secure key for quantum cryptography. The distributed secret key rate is limited by the bandwidth of the nonlinear resonators used for entanglement generation, which is less than 100 MHz for current state-of-the-art setups. The development of an entanglement source with a higher bandwidth promises an increased measurement speed and a linear boost in the secure data rate. Here, we present the experimental realization of a continuous-variable entanglement source with a bandwidth of more than 1.25 GHz. The measured entanglement spectrum was quantified via the inseparability criterion introduced by Duan and coworkers with a critical value of 4 below which entanglement is certified. The measurements yielded an inseparability value of about 1.8 at a frequency of 300 MHz to about 2.8 at 1.2 GHz extending further to about 3.1 at 1.48 GHz. In the experiment we used two 2.6 mm long monolithic PPKTP crystal resonators to generate tw...

  18. A Novel Bandwidth Efficient Transmit Diversity Scheme Based on Water-filling

    Institute of Scientific and Technical Information of China (English)

    SHENCong; DAILin; ZHOUShidong; YAOYan

    2004-01-01

    In this paper we propose a novel bandwidth efficient transmit diversity scheme based on layered space-time architecture, in which Channel state information (CSI) is fully utilized to maximize channel capacity according to water-filling principle. It is shown that compared with V-BLAST, this new scheme can maintain the same high bandwidth efficiency, but achieve much better performance thanks to more effective transmission power allocation and diversity gain.

  19. Transmission Bandwidth Tunability of a Liquid-Filled Photonic Bandgap Fiber

    Institute of Scientific and Technical Information of China (English)

    ZOU Bing; LIU Yan-Ge; DU Jiang-Sing; WANG Zhi; HAN Ting-Ting; XU Jian-Bo; LI Yuan; LIU Bo

    2009-01-01

    @@ A temperature tunable photonic bandgap tiber (PBGF) is demonstrated by an index-guiding photonic crystal fiber filled with high-index liquid. The temperature tunable characteristics of the fiber axe experimentally and numerically investigated. Compression of transmission bandwidth of the PBGF is demonstrated by changing the temperature of part of the fiber. The tunable transmission bandwidth with a range of 250 nm is achieved by changing the temperature from 30℃ to 90℃.

  20. modeling the effect of bandwidth allocation on network performance

    African Journals Online (AJOL)

    a control algorithm that regulates the amount of bandwidth allocated to each ... planning, development and optimization of their networks. PROBLEM ... Network bandwidth design, simulation, and management ...... A Dictionary of Mechanical.

  1. Bandwidth Scale for Frequency Spectrum of Sea Waves

    Institute of Scientific and Technical Information of China (English)

    王伟; 孙孚; 钱成春; 邓拥军

    2000-01-01

    It is well known that energy spectrum bandwidth should be able to reflect the degree of energy concentration. However, the commonly used bandwidth factors defined by Longuet-Higgins could not fit the concept satisfactorily. A new kind of spectrum bandwidth scale factor with a clear physical meaning is given in the present paper and a constant is obtained which reveals the intrinsic characteristics of sea waves. Thereby a universal relationship between significant wave height of sea waves and spectrum bandwidth is established.

  2. Stimulated Brillouin scattering gain bandwidth reduction and applications in microwave photonics and optical signal processing

    Science.gov (United States)

    Preussler, Stefan; Schneider, Thomas

    2016-03-01

    Stimulated Brillouin scattering (SBS) is one of the most dominant nonlinear effects in standard single-mode fibers and its unique spectral characteristics, especially the narrow bandwidth, enable many different applications. Most of the applications would benefit from a narrower bandwidth. Different methods for the bandwidth reduction of SBS in optical fibers are presented and discussed. A bandwidth reduction down to 17% of the natural gain can be achieved by the superposition of the gain with two losses or the utilization of a multistage system. Furthermore, applications in the field of microwave photonics and optical signal processing like high-resolution spectroscopy of communication signals, the storage of optical data packets as well as the processing of frequency combs including generation of millimeter waves and ideal sinc-shaped Nyquist pulses are presented.

  3. Spin-torque diode with tunable sensitivity and bandwidth by out-of-plane magnetic field

    Science.gov (United States)

    Li, X.; Zheng, C.; Zhou, Y.; Kubota, H.; Yuasa, S.; Pong, Philip W. T.

    2016-06-01

    Spin-torque diodes based on nanosized magnetic tunnel junctions are novel microwave detectors with high sensitivity and wide frequency bandwidth. While previous reports mainly focus on improving the sensitivity, the approaches to extend the bandwidth are limited. This work experimentally demonstrates that through optimizing the orientation of the external magnetic field, wide bandwidth can be achieved while maintaining high sensitivity. The mechanism of the frequency- and sensitivity-tuning is investigated through analyzing the dependence of resonant frequency and DC voltage on the magnitude and the tilt angle of hard-plane magnetic field. The frequency dependence is qualitatively explicated by Kittel's ferromagnetic resonance model. The asymmetric resonant frequency at positive and negative magnetic field is verified by the numerical simulation considering the in-plane anisotropy. The DC voltage dependence is interpreted through evaluating the misalignment angle between the magnetization of the free layer and the reference layer. The tunability of the detector performance by the magnetic field angle is evaluated through characterizing the sensitivity and bandwidth under 3D magnetic field. The frequency bandwidth up to 9.8 GHz or maximum sensitivity up to 154 mV/mW (after impedance mismatch correction) can be achieved by tuning the angle of the applied magnetic field. The results show that the bandwidth and sensitivity can be controlled and adjusted through optimizing the orientation of the magnetic field for various applications and requirements.

  4. Varactor-tuned superconducting filter with constant absolute bandwidth at VHF-band

    Energy Technology Data Exchange (ETDEWEB)

    Li, Bo [Department of Physics, Tsinghua University, Beijing 100084 (China); Cao, Bisong, E-mail: bscao@tsinghua.edu.cn [Department of Physics, Tsinghua University, Beijing 100084 (China); Guo, Xubo; Zhang, Xiaoping [Department of Physics, Tsinghua University, Beijing 100084 (China); Chen, Yidong [Superconductor Technology Co., Ltd, Beijing 100085 (China); Wei, Bin; Jiang, Linan [Department of Physics, Tsinghua University, Beijing 100084 (China)

    2015-09-15

    Highlights: • A four-pole superconducting tunable filter at VHF-band with constant absolute bandwidth is proposed. • The novel resonator consists of a spiral-in-spiral-out (SISO) microstrip line with one end shorted to ground and the other loaded with a varactor diode. • Both combline and interdigital constructions for coupling are introduced, and tuned to meet the constant bandwidth requirements. • The measurements show bandwidth variation is less than 1.3% while tuning from 247.28 to 266.58 MHz, and a high Q{sub u} of 1600–5500 is archived. - Abstract: A four-pole superconducting tunable filter at VHF-band with constant absolute bandwidth is proposed. The resonator consists of a spiral-in-spiral-out (SISO) resonator with one end shorted to ground and the other end loaded with a varactor diode. Both combline and interdigital constructions for coupling are introduced, and tuned to meet the constant bandwidth requirement. The fabricated device has a compact size, a tuning range of 7.3% from 247.28 to 266.58, a 3-dB bandwidth of 2.32 ± 0.03 MHz. The insertion loss ranges from 0.5 to 1.6 dB, yielding a high unloaded Q of 1600–5500. The simulated and measured results show an excellent agreement.

  5. A passive available bandwidth estimation methodology

    OpenAIRE

    Cabellos Aparicio, Alberto; Thompson, John; García, Francisco J.; Domingo Pascual, Jordi

    2009-01-01

    The Available Bandwidth (AB) of an end-to-end path is its remaining capacity and it is an important metric for several applications such as overlay routing and P2P networking. That is why many AB estimation tools have been published recently. Most of these tools use the Probe Rate Model, which requires sending packet trains at a rate matching the AB. Its main issue is that it congests the path under measurement. We present a different approach: a novel passive methodology to estimate the AB ...

  6. Confocal microscopy via multimode fibers: fluorescence bandwidth

    Science.gov (United States)

    Loterie, Damien; Psaltis, Demetri; Moser, Christophe

    2016-03-01

    We recently described a method for confocal reflection imaging through fibers, as a way to increase contrast when imaging unstained biological specimens. Using a transmission matrix, focused spots can be created at the distal end of a fiber. The backscattered field coming back from the sample can be filtered using optical correlation to obtain spatial selectivity in the detection. In this proceedings article, we briefly review the working principle of this method, and we discuss how the scheme could be adapted to confocal fluorescence imaging. In particular, we show simulations of the achievable detection bandwidth when using step-index multimode fibers as imaging devices.

  7. Spectrum Assignment with Non-Deterministic Bandwidth of Spectrum Holein Cognitive Radio Networks

    Directory of Open Access Journals (Sweden)

    Huang Jie

    2016-01-01

    Full Text Available The spectrum allocation for cognitive radio networks (CRNs has received considerable studies under the assumption that the bandwidth of spectrum holes is static. However, in practice, the bandwidth of spectrum holes is time-varied due to primary user/secondary user (PU/SU activity and mobility, which result in non-determinacy. This paper studies the spectrum allocation for CRNs with non-deterministic bandwidth of spectrum holes. We present a novel probability density function (PDF model through order statistic to describe the non-deterministic bandwidth of spectrum holes and provide a bound to approximate it. After that, a statistical spectrum allocation model based on stochastic multiple knapsack problem (MKP is established for spectrum allocation with non-deterministic bandwidth of spectrum holes. To reduce the computational complexity, we transform this stochastic programming probleminto a constant MKP though exploiting the properties of cumulative distribution function (CDF, which can be solved via MTHG algorithm by using auxiliary variable. Simulation results illustrate that the proposed statistical spectrum allocation algorithm can achieve better performances compared to the existing algorithms when the bandwidth of spectrum holes istime-varied.

  8. Experimental study and design on high dynamic GNSS receiver using adaptive optimal bandwidth for carrier tracking loop%高动态GNSS接收机载波跟踪环自适应最优带宽设计与试验

    Institute of Scientific and Technical Information of China (English)

    唐康华; 武成锋; 杜亮; 何晓峰

    2014-01-01

    对于大多数高动态接收机,通常采用2阶FLL辅助的3阶PLL环路结构,由于存在FLL环路,导致跟踪精度的下降。针对卫星接收机的动态性能和信号载波功率噪声密度比,在综合考虑接收机跟踪环路中的各种误差源(热噪声、晶振误差、动态牵引误差等)的基础上,采用自适应最优带宽技术,设计一种适用于高动态的3阶PLL载波跟踪环。采用基于GPS数字中频信号的数字仿真和GNSS信号源对所设计的自适应最优带宽进行了验证,验证结果表明:在加速度为30g、过程中存在加加速度为30g/s的高动态情况下,采用18 Hz 3阶PLL不能对信号进行跟踪,而采用所设计的自适应最优带宽的3阶PLL环可以对信号进行可靠的跟踪;同时,和固定带宽接收机比较,所设计载波跟踪环环路能够跟踪50g的高动态Compass卫星信号,而采用固定带宽接收机失锁,并且定位精度优于1 m(2σ),测速精度优于0.2 m/s(2σ)。%For most GNSS receiver designs in high dynamic application, a second-order FLL aided 3rd order PLL is usually adopted as carrier tracking loop. Based on GNSS receiver dynamics and carrier power-to-noise density, the structure of GNSS receiver 3rd order PLL tracking loop for high dynamic applications was designed by using the adaptive optimal bandwidth method and taking the tracking errors(such as thermal noise, oscillator phase noise, dynamic stress error) into account. According to the designed adaptive optimal bandwidth method of the 3rd order PLL tracking loop, the digital simulation and test based GNSS simulator were performed. Simulation results show that on the condition of 30g line-of-sight acceleration and 30g/s jerk high dynamics, the designed adaptive optimal bandwidth method can track GNSS signal well, but when using the 18 Hz fixed-bandwidth 3rd order PLL, carrier tracking lock will be lost. When using the GNSS simulator, test results show that

  9. Bandwidth Partitioning in Decentralized Wireless Networks

    CERN Document Server

    Jindal, Nihar; Weber, Steven

    2007-01-01

    This paper addresses the following question, which is of interest in the design of a multiuser decentralized network. Given a total system bandwidth of W Hz and a fixed data rate constraint of R bps for each transmission, how many frequency slots N of size W/N should the band be partitioned into in order to maximize the number of simultaneous links in the network? Dividing the available spectrum results in two competing effects. On the positive side, a larger N allows for more parallel, non-interfering communications to take place in the same area. On the negative side, a larger N increases the SINR requirement for each link because the same information rate must be achieved over less bandwidth, which in turn increases the area consumed by each transmission. Exploring this tradeoff and determining the optimum value of N in terms of the system parameters is the focus of the paper. Using stochastic geometry, the optimal SINR threshold - which directly corresponds to the optimal spectral efficiency - is derived ...

  10. Bandwidth sharing networks with multiscale traffic

    Directory of Open Access Journals (Sweden)

    Mathieu Feuillet

    2015-03-01

    Full Text Available In multi-class communication networks, traffic surges due to one class of users can significantly degrade the performance for other classes. During these transient periods, it is thus of crucial importance to implement priority mechanisms that conserve the quality of service experienced by the affected classes, while ensuring that the temporarily unstable class is not entirely neglected. In this paper, we examine the complex interaction occurring between several classes of traffic when classes obtain bandwidth proportionally to their incoming traffic. We characterize the evolution of the performance measures of the network from the moment the initial surge takes place until the system reaches its equilibrium. Using a time-space-transition-scaling, we show that the trajectories of the temporarily unstable class can be described by a differential equation, while those of the stable classes retain their stochastic nature. In particular, we show that the temporarily unstable class evolves at a time-scale which is much slower than that of the stable classes. Although the time-scales decouple, the dynamics of the temporarily unstable and the stable classes continue to influence one another. We further proceed to characterize the obtained differential equations for several simple network examples. In particular, the macroscopic asymptotic behavior of the unstable class allows us to gain important qualitative insights on how the bandwidth allocation affects performance. We illustrate these results on several toy examples and we finally build a penalization rule using these results for a network integrating streaming and surging elastic traffic.

  11. Bandwidth Extension of Telephone Speech Aided by Data Embedding

    Directory of Open Access Journals (Sweden)

    David Malah

    2007-01-01

    Full Text Available A system for bandwidth extension of telephone speech, aided by data embedding, is presented. The proposed system uses the transmitted analog narrowband speech signal as a carrier of the side information needed to carry out the bandwidth extension. The upper band of the wideband speech is reconstructed at the receiving end from two components: a synthetic wideband excitation signal, generated from the narrowband telephone speech and a wideband spectral envelope, parametrically represented and transmitted as embedded data in the telephone speech. We propose a novel data embedding scheme, in which the scalar Costa scheme is combined with an auditory masking model allowing high rate transparent embedding, while maintaining a low bit error rate. The signal is transformed to the frequency domain via the discrete Hartley transform (DHT and is partitioned into subbands. Data is embedded in an adaptively chosen subset of subbands by modifying the DHT coefficients. In our simulations, high quality wideband speech was obtained from speech transmitted over a telephone line (characterized by spectral magnitude distortion, dispersion, and noise, in which side information data is transparently embedded at the rate of 600 information bits/second and with a bit error rate of approximately 3⋅10−4. In a listening test, the reconstructed wideband speech was preferred (at different degrees over conventional telephone speech in 92.5% of the test utterances.

  12. Bandwidth Extension of Telephone Speech Aided by Data Embedding

    Directory of Open Access Journals (Sweden)

    Sagi Ariel

    2007-01-01

    Full Text Available A system for bandwidth extension of telephone speech, aided by data embedding, is presented. The proposed system uses the transmitted analog narrowband speech signal as a carrier of the side information needed to carry out the bandwidth extension. The upper band of the wideband speech is reconstructed at the receiving end from two components: a synthetic wideband excitation signal, generated from the narrowband telephone speech and a wideband spectral envelope, parametrically represented and transmitted as embedded data in the telephone speech. We propose a novel data embedding scheme, in which the scalar Costa scheme is combined with an auditory masking model allowing high rate transparent embedding, while maintaining a low bit error rate. The signal is transformed to the frequency domain via the discrete Hartley transform (DHT and is partitioned into subbands. Data is embedded in an adaptively chosen subset of subbands by modifying the DHT coefficients. In our simulations, high quality wideband speech was obtained from speech transmitted over a telephone line (characterized by spectral magnitude distortion, dispersion, and noise, in which side information data is transparently embedded at the rate of 600 information bits/second and with a bit error rate of approximately . In a listening test, the reconstructed wideband speech was preferred (at different degrees over conventional telephone speech in of the test utterances.

  13. Unmanned Aircraft System Control and ATC Communications Bandwidth Requirements

    Science.gov (United States)

    Henriksen, Steve

    2008-01-01

    There are significant activities taking place to establish the procedures and requirements for safe and routine operation of unmanned aircraft systems (UAS) in the National Airspace System (NAS). Among the barriers to overcome in achieving this goal is the lack of sufficient frequency spectrum necessary for the UAS control and air traffic control (ATC) communications links. This shortcoming is compounded by the fact that the UAS control communications links will likely be required to operate in protected frequency spectrum, just as ATC communications links are, because they relate to "safety and regularity of flight." To support future International Telecommunications Union (ITU) World Radio Conference (WRC) agenda items concerning new frequency allocations for UAS communications links, and to augment the Future Communications Study (FCS) Technology Evaluation Group efforts, NASA Glenn Research Center has sponsored a task to estimate the UAS control and ATC communications bandwidth requirements for safe, reliable, and routine operation of UAS in the NAS. This report describes the process and results of that task. The study focused on long-term bandwidth requirements for UAS approximately through 2030.

  14. An analysis on the mid-latitude scintillation and coherence frequency bandwidth using transionospheric VHF signals

    Energy Technology Data Exchange (ETDEWEB)

    Juang, Zhen [Los Alamos National Laboratory; Roussel-dupre, Robert [Los Alamos National Laboratory

    2008-01-01

    An analysis was perfonned on the mid-latitude scintillation and coherence frequency bandwidth (Fcoh) using transionospheric VHF signal data. The data include 1062 events spanning from November 1997 to June 2002. Each event records FORTE satellite received VHF signals from LAPP located at Los Alamos, New Mexico. Fcohs were derived to study scintillation characteristics on diurnal and seasonal variations, as well as changes due to solar and geomagnetic activities. Comparisons to the VHFIUHF coherence frequency bandwidth studies previously reported at equatorial and mid-latitude regions are made using a 4th power frequency dependence relationship. Furthennore, a wideband ionospheric scintillation model, WBMOD, was used to estimate Fcohs and compared with our VHF Fcoh values. Our analysis indicates mid-latitude scintillation characteristics that are not previously revealed. At the VHF bottom frequency range (3035 MHz), distinguished smaller Fcohs are found in time period from sunset to midnight, in wann season from May to August, and in low solar activity years. The effects of geomagnetic storm activity on Fcoh are characterized by a sudden transition at a Kp index of 50-60. Comparisons with median Fcohs estimated from other studies validated our VHF Fcohs for daytime while an order of magnitude larger Fcohs are found for nighttime, implying a time-dependent issue in applying the 4th order power relationship. Furthermore, comparisons with WBMOD-estimated Fcohs indicated generally matched median scintillation level estimates while differences do exist for those events undergoing high geomagnetic stonn activity which may imply underestimates of scintillation level by the WBMOD in the mid-latitude regions.

  15. Bandwidth Analysis of Smart Meter Network Infrastructure

    DEFF Research Database (Denmark)

    Balachandran, Kardi; Olsen, Rasmus Løvenstein; Pedersen, Jens Myrup

    2014-01-01

    Advanced Metering Infrastructure (AMI) is a net-work infrastructure in Smart Grid, which links the electricity customers to the utility company. This network enables smart services by making it possible for the utility company to get an overview of their customers power consumption and also control...... devices in their costumers household e.g. heat pumps. With these smart services, utility companies can do load balancing on the grid by shifting load using resources the customers have. The problem investigated in this paper is what bandwidth require-ments can be expected when implementing such network...... to utilize smart meters and which existing broadband network technologies can facilitate this smart meter service. Initially, scenarios for smart meter infrastructure are identified. The paper defines abstraction models which cover the AMI scenarios. When the scenario has been identified a general overview...

  16. Optimal filter bandwidth for pulse oximetry

    Science.gov (United States)

    Stuban, Norbert; Niwayama, Masatsugu

    2012-10-01

    Pulse oximeters contain one or more signal filtering stages between the photodiode and microcontroller. These filters are responsible for removing the noise while retaining the useful frequency components of the signal, thus improving the signal-to-noise ratio. The corner frequencies of these filters affect not only the noise level, but also the shape of the pulse signal. Narrow filter bandwidth effectively suppresses the noise; however, at the same time, it distorts the useful signal components by decreasing the harmonic content. In this paper, we investigated the influence of the filter bandwidth on the accuracy of pulse oximeters. We used a pulse oximeter tester device to produce stable, repetitive pulse waves with digitally adjustable R ratio and heart rate. We built a pulse oximeter and attached it to the tester device. The pulse oximeter digitized the current of its photodiode directly, without any analog signal conditioning. We varied the corner frequency of the low-pass filter in the pulse oximeter in the range of 0.66-15 Hz by software. For the tester device, the R ratio was set to R = 1.00, and the R ratio deviation measured by the pulse oximeter was monitored as a function of the corner frequency of the low-pass filter. The results revealed that lowering the corner frequency of the low-pass filter did not decrease the accuracy of the oxygen level measurements. The lowest possible value of the corner frequency of the low-pass filter is the fundamental frequency of the pulse signal. We concluded that the harmonics of the pulse signal do not contribute to the accuracy of pulse oximetry. The results achieved by the pulse oximeter tester were verified by human experiments, performed on five healthy subjects. The results of the human measurements confirmed that filtering out the harmonics of the pulse signal does not degrade the accuracy of pulse oximetry.

  17. Bandwidth Improvement of UWB Microstrip Antenna Using Finite Ground Plane

    Directory of Open Access Journals (Sweden)

    Priyanka Mishra

    2015-06-01

    Full Text Available Microstrip antennas play a vital role in communication system. It is required in high performance wireless applications. But due to its resonant nature microstrip antennas have some considerable drawbacks like narrowband performance. Extensive study has been carried out on microstrip patch antennas in the recent past, but it still have large scope for improvement in the near future. To overcome narrow bandwidth problem, number of methods and techniques have been suggested and investigated, keeping in mind that the basic advantages of microstrip antenna should not be altered such as low profile, light weight, low cost and simple printed circuit structure. The area of investigation includes modification in geometrical shape of the antenna, use of resonators, use of dipole, and many other parameters. This paper presents a comparison between conventional microstrip antenna and microstip antenna with finite ground plane at ultra wideband. HFSS simulation tool is used here for antenna simulation. For feeding purpose microstrip feed line is used (50Ω. Optimized result provides impedance bandwidth of 7.2GHz with VSWR<2, operating frequency range is from 6.5GHz to 13.7GHz. Proposed antenna is useful for many ultra wideband applications.

  18. The Wideband Slope of Interference Channels: The Infinite Bandwidth Case

    CERN Document Server

    Shen, Minqi

    2010-01-01

    It is well known that minimum received energy per bit in the interference channel is $-1.59dB$ as if there were no interference. Thus, the best way to mitigate interference is to operate the interference channel in the low power regime, that is in the limit of infinite bandwidth. However, when the bandwidth is large, but finite, minimum received energy per bit alone does not characterize performance. Verdu introduced the wideband slope $\\mathcal{S}_{0}$ to characterize the performance in this regime. We show that a wideband slope of ${\\mathcal{S}_{0}}/{\\mathcal{S}_{0,{no interference}}}=1/2$ is achievable. This result is similar to recent results on degrees of freedom in the high SNR regime, and we use a type of interference alignment using delays to obtain the result. We also show that in many cases the wideband slope is upper bounded by ${\\mathcal{S}_{0}}/{\\mathcal{S}_{0,{no interference}}}\\leq 1/2}$ for large number of users $K$.

  19. Improving microwave antenna gain and bandwidth with phase compensation metasurface

    Directory of Open Access Journals (Sweden)

    Ke Chen

    2015-06-01

    Full Text Available Metasurface, as a planar version of artificial metamaterial, provide an effective way to manipulate electromagnetic wave propagation. Here, we present a transparent metasurface for compensating the out-of-phase radiation from a microstrip patch antenna to improve its radiation gain and bandwidth. Based on the equivalence principle of Huygens’ surface, we propose metasurface composed of both inductive and capacitive resonant elements which could produce high transmission with variable phase characteristics. Such metasurface mounted on a patch antenna can transform the spherical-like phase profile generated from the patch into an in-phase planar one. A prototype antenna has been fabricated and validated the squeezed radiation pattern with suppressed sidelobes as well as enhanced impedance bandwidth due to strong near-field coupling. As operating at around 5.7 GHz, the proposed antenna may have potential application in wireless communication systems especially for point-to-point data transmission. It is believed that the design methodology could also be scaled to other frequency bands such as millimeter or terahertz wave.

  20. Improving microwave antenna gain and bandwidth with phase compensation metasurface

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Ke; Yang, Zhongjie; Feng, Yijun, E-mail: yjfeng@nju.edu.cn; Zhu, Bo; Zhao, Junming; Jiang, Tian [Department of Electronic Engineering, School of Electronic Science and Engineering, Nanjing University, Nanjing, 210093 (China)

    2015-06-15

    Metasurface, as a planar version of artificial metamaterial, provide an effective way to manipulate electromagnetic wave propagation. Here, we present a transparent metasurface for compensating the out-of-phase radiation from a microstrip patch antenna to improve its radiation gain and bandwidth. Based on the equivalence principle of Huygens’ surface, we propose metasurface composed of both inductive and capacitive resonant elements which could produce high transmission with variable phase characteristics. Such metasurface mounted on a patch antenna can transform the spherical-like phase profile generated from the patch into an in-phase planar one. A prototype antenna has been fabricated and validated the squeezed radiation pattern with suppressed sidelobes as well as enhanced impedance bandwidth due to strong near-field coupling. As operating at around 5.7 GHz, the proposed antenna may have potential application in wireless communication systems especially for point-to-point data transmission. It is believed that the design methodology could also be scaled to other frequency bands such as millimeter or terahertz wave.

  1. Improving microwave antenna gain and bandwidth with phase compensation metasurface

    Science.gov (United States)

    Chen, Ke; Yang, Zhongjie; Feng, Yijun; Zhu, Bo; Zhao, Junming; Jiang, Tian

    2015-06-01

    Metasurface, as a planar version of artificial metamaterial, provide an effective way to manipulate electromagnetic wave propagation. Here, we present a transparent metasurface for compensating the out-of-phase radiation from a microstrip patch antenna to improve its radiation gain and bandwidth. Based on the equivalence principle of Huygens' surface, we propose metasurface composed of both inductive and capacitive resonant elements which could produce high transmission with variable phase characteristics. Such metasurface mounted on a patch antenna can transform the spherical-like phase profile generated from the patch into an in-phase planar one. A prototype antenna has been fabricated and validated the squeezed radiation pattern with suppressed sidelobes as well as enhanced impedance bandwidth due to strong near-field coupling. As operating at around 5.7 GHz, the proposed antenna may have potential application in wireless communication systems especially for point-to-point data transmission. It is believed that the design methodology could also be scaled to other frequency bands such as millimeter or terahertz wave.

  2. BECSI: Bandwidth Efficient Certificate Status Information Distribution Mechanism for VANETs

    Directory of Open Access Journals (Sweden)

    Carlos Gañán

    2013-01-01

    Full Text Available Certificate revocation is a challenging task, especiallyin mobile network environments such as vehicular ad Hoc networks (VANETs.According to the IEEE 1609.2 security standard for VANETs, public keyinfrastructure (PKI will provide this functionality by means of certificate revocation lists (CRLs.When a certificate authority (CAneeds to revoke a certificate, itglobally distributes CRLs.Transmitting these lists pose a problem as they require high update frequencies and a lot of bandwidth. In this article, we propose BECSI, aBandwidth Efficient Certificate Status Informationmechanism to efficiently distributecertificate status information (CSI in VANETs.By means of Merkle hash trees (MHT, BECSI allowsto retrieve authenticated CSI not onlyfrom the infrastructure but also from vehicles actingas mobile repositories.Since these MHTs are significantly smaller than the CRLs, BECSIreduces the load on the CSI repositories and improves the response time for the vehicles.Additionally, BECSI improves the freshness of the CSIby combining the use of delta-CRLs with MHTs.Thus, vehicles that have cached the most current CRLcan download delta-CRLs to have a complete list of revoked certificates.Once a vehicle has the whole list of revoked certificates, it can act as mobile repository.

  3. Investigating the influence of chromatic aberration and optical illumination bandwidth on fundus imaging in rats

    Science.gov (United States)

    Li, Hao; Liu, Wenzhong; Zhang, Hao F.

    2015-10-01

    Rodent models are indispensable in studying various retinal diseases. Noninvasive, high-resolution retinal imaging of rodent models is highly desired for longitudinally investigating the pathogenesis and therapeutic strategies. However, due to severe aberrations, the retinal image quality in rodents can be much worse than that in humans. We numerically and experimentally investigated the influence of chromatic aberration and optical illumination bandwidth on retinal imaging. We confirmed that the rat retinal image quality decreased with increasing illumination bandwidth. We achieved the retinal image resolution of 10 μm using a 19 nm illumination bandwidth centered at 580 nm in a home-built fundus camera. Furthermore, we observed higher chromatic aberration in albino rat eyes than in pigmented rat eyes. This study provides a design guide for high-resolution fundus camera for rodents. Our method is also beneficial to dispersion compensation in multiwavelength retinal imaging applications.

  4. Planning High-Risk High-Reward Activities.

    NARCIS (Netherlands)

    Casault, Sébastien

    2014-01-01

    This body of work addresses a gap in financial and economic theories related to assets that are typically associated with high uncertainty. Specifically, this thesis provides some foundational work towards a new way to quantify and explain how high-risk high-reward activities, such as exploration,

  5. Adaptable Bandwidth for Harmonic Step-Frequency Radar

    Directory of Open Access Journals (Sweden)

    Anthony F. Martone

    2015-01-01

    Full Text Available A spectrum sensing technique is described which is used to enhance the performance of harmonic step-frequency radar in the presence of harmful radio frequency (RF interference (RFI. This technique passively monitors the RF spectrum for subbands of high signal-to-interference-plus-noise ratio (SINR within a constrained bandwidth of interest. An optimal subband is selected for the harmonic radar that maximizes SINR and minimizes the range resolution cell size, two conflicting objectives. The approach is tested using an experimental setup that injects high power RFI into a harmonic step-frequency radar, which significantly degrades radar performance. It is shown that the proposed spectrum sensing technique significantly improves the SINR and the peak-to-average sidelobe power level of the harmonic radar at the sacrifice of range resolution.

  6. Frequency Bandwidth Optimization of Left-Handed Metamaterial

    Science.gov (United States)

    Chevalier, Christine T.; Wilson, Jeffrey D.

    2004-01-01

    Recently, left-handed metamaterials (LHM s) have been demonstrated with an effective negative index of refraction and with antiparallel group and phase velocities for microwave radiation over a narrow frequency bandwidth. In order to take advantage of these characteristics for practical applications, it will be beneficial to develop LHM s with increased frequency bandwidth response and lower losses. In this paper a commercial three-dimensional electromagnetic simulation code is used to explore the effects of geometry parameter variations on the frequency bandwidth of a LHM at microwave frequencies. Utilizing an optimizing routine in the code, a geometry was generated with a bandwidth more than twice as large as the original geometry.

  7. Effective Bandwidth Utilization in IEEE802.11 for VOIP

    CERN Document Server

    Bhanu, S Vijay; Balakrishnan, V

    2010-01-01

    Voice over Internet protocol (VoIP) is one of the most important applications for the IEEE 802.11 wireless local area networks (WLANs). For network planners who are deploying VoIP over WLANs, one of the important issues is the VoIP capacity. VoIP bandwidth consumption over a WAN is one of the most important factors to consider when building a VoIP infrastructure. Failure to account for VoIP bandwidth requirements will severely limit the reliability of a VoIP system and place a huge burden on the WAN infrastructure. Less bandwidth utilization is the key reasons for reduced number of channel accesses in VOIP. But in the QoS point of view the free bandwidth of atleast 1-5% will improve the voice quality. This proposal utilizes the maximum bandwidth by leaving 1-5% free bandwidth. A Bandwidth Data rate Moderation (BDM) algorithm has been proposed which correlates the data rate specified in IEEE802.11b with the free bandwidth. At each time BDM will calculate the bandwidth utilization before sending the packet to i...

  8. Influence of carrier dynamics on the modulation bandwidth of quantum-dot based nanocavity devices

    DEFF Research Database (Denmark)

    Lorke, Michael; Nielsen, Torben Roland; Mørk, Jesper

    2010-01-01

    We theoretically investigate the modulation response of quantum-dot based nanocavity light emitting devices. For high Purcell enhancement factors, our theory predicts the possibility of decreasing the modulation bandwidth with increasing scattering rate into the lasing quantum-dot state. This cou......We theoretically investigate the modulation response of quantum-dot based nanocavity light emitting devices. For high Purcell enhancement factors, our theory predicts the possibility of decreasing the modulation bandwidth with increasing scattering rate into the lasing quantum-dot state...

  9. Power and Efficiency Optimized in Traveling-Wave Tubes Over a Broad Frequency Bandwidth

    Science.gov (United States)

    Wilson, Jeffrey D.

    2001-01-01

    A traveling-wave tube (TWT) is an electron beam device that is used to amplify electromagnetic communication waves at radio and microwave frequencies. TWT's are critical components in deep space probes, communication satellites, and high-power radar systems. Power conversion efficiency is of paramount importance for TWT's employed in deep space probes and communication satellites. A previous effort was very successful in increasing efficiency and power at a single frequency (ref. 1). Such an algorithm is sufficient for narrow bandwidth designs, but for optimal designs in applications that require high radiofrequency power over a wide bandwidth, such as high-density communications or high-resolution radar, the variation of the circuit response with respect to frequency must be considered. This work at the NASA Glenn Research Center is the first to develop techniques for optimizing TWT efficiency and output power over a broad frequency bandwidth (ref. 2). The techniques are based on simulated annealing, which has the advantage over conventional optimization techniques in that it enables the best possible solution to be obtained (ref. 3). Two new broadband simulated annealing algorithms were developed that optimize (1) minimum saturated power efficiency over a frequency bandwidth and (2) simultaneous bandwidth and minimum power efficiency over the frequency band with constant input power. The algorithms were incorporated into the NASA coupled-cavity TWT computer model (ref. 4) and used to design optimal phase velocity tapers using the 59- to 64-GHz Hughes 961HA coupled-cavity TWT as a baseline model. In comparison to the baseline design, the computational results of the first broad-band design algorithm show an improvement of 73.9 percent in minimum saturated efficiency (see the top graph). The second broadband design algorithm (see the bottom graph) improves minimum radiofrequency efficiency with constant input power drive by a factor of 2.7 at the high band edge (64

  10. Bandwidth Efficient Hybrid Synchronization for Wireless Sensor Network

    DEFF Research Database (Denmark)

    Dnyaneshwar, Mantri; Prasad, Neeli R.; Prasad, Ramjee

    2015-01-01

    Data collection and transmission are the fundamental operations of Wireless Sensor Networks (WSNs). A key challenge in effective data collection and transmission is to schedule and synchronize the activities of the nodes with the global clock. This paper proposes the Bandwidth Efficient Hybrid...... Synchronization Data Aggregation Algorithm (BESDA) using spanning tree mechanism (SPT). It uses static sink and mobile nodes in the network. BESDA considers the synchronization of a local clock of node with global clock of the network. In the initial stage algorithm established the hierarchical structure...... in the network and then perform the pair-wise synchronization. With the mobility of node, the structure frequently changes causing an increase in energy consumption. To mitigate the problem BESDA aggregate data with the notion of a global timescale throughout the network and schedule based time-division multiple...

  11. A Novel Effective Bandwidth Based Call Admission Control for Multimedia CDMA Systems

    Institute of Scientific and Technical Information of China (English)

    PAN Su; FENG Guang-zheng; ZHU Qi

    2004-01-01

    A novel Call Admission Control (CAC) scheme is proposed for multimedia CDMA systems. The effective bandwidth of real time calls is reserved in the CAC with the consideration of active factors. The admission of non-real time calls is controlled by the system according to the residual effective bandwidth left from real time calls. Simulation results have shown that the novel CAC has greatly enlarged the admission region for real time calls and make the transmission delay of non-real time calls under an acceptable level.

  12. High effective silica fume alkali activator

    Indian Academy of Sciences (India)

    Vladimír Živica

    2004-04-01

    Growing demands on the engineering properties of cement based materials and the urgency to decrease unsuitable ecologic impact of Portland cement manufacturing represent significant motivation for the development of new cement corresponding to these aspects. One category represents prospective alkali activated cements. A significant factor influencing their properties is alkali activator used. In this paper we present a new high effective alkali activator prepared from silica fume and its effectiveness. According to the results obtained this activator seems to be more effective than currently used activators like natrium hydroxide, natrium carbonate, and water glass.

  13. Studies of bandwidth dependence of laser plasma instabilities driven by the Nike laser

    Science.gov (United States)

    Weaver, J.; Kehne, D.; Obenschain, S.; Serlin, V.; Schmitt, A. J.; Oh, J.; Lehmberg, R. H.; Brown, C. M.; Seely, J.; Feldman, U.

    2012-10-01

    Experiments at the Nike laser facility of the Naval Research Laboratory are exploring the influence of laser bandwidth on laser plasma instabilities (LPI) driven by a deep ultraviolet pump (248 nm) that incorporates beam smoothing by induced spatial incoherence (ISI). In early ISI studies with longer wavelength Nd:glass lasers (1054 nm and 527 nm),footnotetextObenschain, PRL 62(1989);Mostovych, PRL 62(1987);Peyser, Phys. Fluids B 3(1991). stimulated Raman scattering, stimulated Brillouin scattering, and the two plasmon decay instability were reduced when wide bandwidth ISI (δν/ν˜0.03-0.19%) pulses irradiated targets at moderate to high intensities (10^14-10^15 W/cm^2). The current studies will compare the emission signatures of LPI from planar CH targets during Nike operation at large bandwidth (δν˜1THz) to observations for narrower bandwidth operation (δν˜0.1-0.3THz). These studies will help clarify the relative importance of the short wavelength and wide bandwidth to the increased LPI intensity thresholds observed at Nike. New pulse shapes are being used to generate plasmas with larger electron density scale-lengths that are closer to conditions during pellet implosions for direct drive inertial confinement fusion.

  14. Memory bandwidth-scalable motion estimation for mobile video coding

    Science.gov (United States)

    Hsieh, Jui-Hung; Tai, Wei-Cheng; Chang, Tian-Sheuan

    2011-12-01

    The heavy memory access of motion estimation (ME) execution consumes significant power and could limit ME execution when the available memory bandwidth (BW) is reduced because of access congestion or changes in the dynamics of the power environment of modern mobile devices. In order to adapt to the changing BW while maintaining the rate-distortion (R-D) performance, this article proposes a novel data BW-scalable algorithm for ME with mobile multimedia chips. The available BW is modeled in a R-D sense and allocated to fit the dynamic contents. The simulation result shows 70% BW savings while keeping equivalent R-D performance compared with H.264 reference software for low-motion CIF-sized video. For high-motion sequences, the result shows our algorithm can better use the available BW to save an average bit rate of up to 13% with up to 0.1-dB PSNR increase for similar BW usage.

  15. Efficiently parallelized modeling of tightly focused, large bandwidth laser pulses

    CERN Document Server

    Dumont, Joey; Lefebvre, Catherine; Gagnon, Denis; MacLean, Steve

    2016-01-01

    The Stratton-Chu integral representation of electromagnetic fields is used to study the spatio-temporal properties of large bandwidth laser pulses focused by high numerical aperture mirrors. We review the formal aspects of the derivation of diffraction integrals from the Stratton-Chu representation and discuss the use of the Hadamard finite part in the derivation of the physical optics approximation. By analyzing the formulation we show that, for the specific case of a parabolic mirror, the integrands involved in the description of the reflected field near the focal spot do not possess the strong oscillations characteristic of diffraction integrals. Consequently, the integrals can be evaluated with simple and efficient quadrature methods rather than with specialized, more costly approaches. We report on the development of an efficiently parallelized algorithm that evaluates the Stratton-Chu diffraction integrals for incident fields of arbitrary temporal and spatial dependence. We use our method to show that t...

  16. MATLAB implementation of a dynamic clamp with bandwidth >125 KHz capable of generating INa at 37°C

    Science.gov (United States)

    Clausen, Chris; Valiunas, Virginijus; Brink, Peter R.; Cohen, Ira S.

    2012-01-01

    We describe the construction of a dynamic clamp with bandwidth >125 KHz that utilizes a high performance, yet low cost, standard home/office PC interfaced with a high-speed (16 bit) data acquisition module. High bandwidth is achieved by exploiting recently available software advances (code-generation technology, optimized real-time kernel). Dynamic-clamp programs are constructed using Simulink, a visual programming language. Blocks for computation of membrane currents are written in the high-level matlab language; no programming in C is required. The instrument can be used in single- or dual-cell configurations, with the capability to modify programs while experiments are in progress. We describe an algorithm for computing the fast transient Na+ current (INa) in real time, and test its accuracy and stability using rate constants appropriate for 37°C. We then construct a program capable of supplying three currents to a cell preparation: INa, the hyperpolarizing-activated inward pacemaker current (If), and an inward-rectifier K+ current (IK1). The program corrects for the IR drop due to electrode current flow, and also records all voltages and currents. We tested this program on dual patch-clamped HEK293 cells where the dynamic clamp controls a current-clamp amplifier and a voltage-clamp amplifier controls membrane potential, and current-clamped HEK293 cells where the dynamic clamp produces spontaneous pacing behavior exhibiting Na+ spikes in otherwise passive cells. PMID:23224681

  17. Optimal Bandwidth Selection in Observed-Score Kernel Equating

    Science.gov (United States)

    Häggström, Jenny; Wiberg, Marie

    2014-01-01

    The selection of bandwidth in kernel equating is important because it has a direct impact on the equated test scores. The aim of this article is to examine the use of double smoothing when selecting bandwidths in kernel equating and to compare double smoothing with the commonly used penalty method. This comparison was made using both an equivalent…

  18. 47 CFR 78.104 - Authorized bandwidth and emission designator.

    Science.gov (United States)

    2010-10-01

    ... SERVICES CABLE TELEVISION RELAY SERVICE Technical Regulations § 78.104 Authorized bandwidth and emission... within the frequency limits of the assigned channel. (c) The emission designator shall be specified in... 47 Telecommunication 4 2010-10-01 2010-10-01 false Authorized bandwidth and emission...

  19. Avoiding bandwidth collapse in long chains of coupled optical microresonators.

    Science.gov (United States)

    Mookherjea, Shayan; Schneider, Mark A

    2011-12-01

    Coupled photonic oscillators and resonators are sensitive to unavoidable nanoscale disorder, and localization in periodic structures induced by disorder leads eventually to a complete collapse of the bandwidth, which is generally considered problematic for device applications. Here, we investigate the dependence of bandwidth collapse on the interresonator coupling coefficient, a parameter controllable by lithography or device operation.

  20. E-Readiness Assessment Model for Low Bandwidth Environment

    Directory of Open Access Journals (Sweden)

    Nazir Ahmad Suhail

    Full Text Available This paper reports on assessment of an e-readiness model for low bandwidth environment. The main focus of the model is on technological (bandwidth related critical factors that are barrier to the adoption of technology mediated learning in developing cou ...

  1. Global path and bandwidth scheduling in inter-data-center IP/optical transport network

    Science.gov (United States)

    Zhao, Yang; Wang, Lei; Chen, Xue; Yang, Futao; Shi, Sheping; Wang, Huitao

    2016-07-01

    We propose a flow-oriented global path and bandwidth scheduling scheme for inter-data-center IP/optical network. To improve the throughput of network and reduce the mutual impact between flows, we allow each flow to be carried by a multi-path optical channel data unit (ODU) channel. In addition bandwidth is allocated to flows fairly according to weight. Simulation results reveal that compared to high-priority-first mechanism, the method proposed improves average bandwidth allocation ratio by about 15% and allocation fairness between flows by 30%. Furthermore, compared to pure IP network, router ports are significantly saved and network cost can be reduced by up to 40% with scheme proposed in unified controlled IP/optical network.

  2. Amplifying modeling for broad bandwidth pulse in Nd:glass based on hybrid-broaden mechanism

    Energy Technology Data Exchange (ETDEWEB)

    Sujingqin; Lanqin, L; Wenyi, W; Feng, J; Xiaofeng, W; Xiaomin, Z [Research Center of Laser Fusion, China Academy of Engineering Physics, P. O. Box 919-988, Mianyang, China, 621900 (China); Bin, L [School of Computer and Communication Engineering, Southwest Jiaotong University, Chengdu. China, 610031 (China)], E-mail: sujingqin@tom.com

    2008-05-15

    In this paper, the cross relaxation time is proposed to combine the homogeneous and inhomogeneous broaden mechanism for broad bandwidth pulse amplification model. The corresponding velocity equation, which can describe the response of inverse population on upper and low energy level of gain media to different frequency of pulse, is also put forward. The gain saturation and energy relaxation effect are also included in the velocity equation. Code named CPAP has been developed to simulate the amplifying process of broad bandwidth pulse in multi-pass laser system. The amplifying capability of multi-pass laser system is evaluated and gain narrowing and temporal shape distortion are also investigated when bandwidth of pulse and cross relaxation time of gain media are different. Results can benefit the design of high-energy PW laser system in LFRC, CAEP.

  3. Three-Dimensional Single-Port Labyrinthine Acoustic Metamaterial: Perfect Absorption with Large Bandwidth and Tunability

    Science.gov (United States)

    Zhang, Chi; Hu, Xinhua

    2016-12-01

    Metamaterials are engineered materials which exhibit fascinating properties unreachable by traditional materials. Here, we report on the design, fabrication, and experimental characterization of a three-dimensional single-port labyrinthine acoustic metamaterial. By using curled perforations with one end closed and with appropriate loss inside, the metamaterial can perfectly absorb airborne sounds in a low-frequency band. Both the position and the relative width of the band can be tuned flexibly. A trade-off is uncovered between the relative absorption bandwidth and thickness of the metamaterial. When the relative absorption bandwidth is as high as 51%, the requirement of deep-subwavelength thickness (0.07 λ ) can still be satisfied. We emphasize that the perfect absorption with large tunability in relative bandwidth (from 9% to >180 % ) was not attainable previously and may find applications ranging from noise reduction to sound imaging.

  4. Theoretical study on the ultra-narrow bandwidth tunable atomic filter with electromagnetically induced transparency

    Science.gov (United States)

    Liu, Yang; Li, Shu-qing; Feng, Zhong-ying; Liu, Xiao-fei; Gao, Jin-yue

    2016-12-01

    To obtain the weak signal light detection from the high background noise, we present a theoretical study on the ultra-narrow bandwidth tunable atomic filter with electromagnetically induced transparency. In a three-level Λ -type atomic system in the rubidium D1 line, the bandwidth of the EIT atomic filter is narrowed to ~6.5 \\text{MHz} . And the single peak transmission of the filter can be up to 86% . Moreover, the transmission wavelength can be tuned by changing the coupling light frequency. This theoretical scheme can also be applied to other alkali atomic systems.

  5. Metamaterial composite bandpass filter with an ultra-broadband rejection bandwidth of up to 240 terahertz

    DEFF Research Database (Denmark)

    Strikwerda, Andrew; Zalkovskij, Maksim; Lorenzen, Dennis Lund

    2014-01-01

    We present a metamaterial, consisting of a cross structure and a metal mesh filter, that forms a composite with greater functional bandwidth than any terahertz (THz) metamaterial to date. Metamaterials traditionally have a narrow usable bandwidth that is much smaller than common THz sources...... frequency (f) that is scalable from 0.86–8.51 THz, that highly extinguishes other frequencies up to >240 THz. The performance of these filters is demonstrated in experiment, using both air biased coherent detection and a Fourier transform infrared spectrometer (FTIR), as well as in simulation. We present...

  6. A Wideband Supply Modulator for 20MHz RF Bandwidth Polar PAs in 65nm CMOS

    NARCIS (Netherlands)

    Shrestha, R.; van der Zee, Ronan A.R.; de Graauw, Anton; Nauta, Bram

    2009-01-01

    Polar modulated RF amplifiers have the potential to enhance efficiency while achieving sufficient linearity for a signal having non-constant envelope. However, switching modulators used in such architectures to generate the envelope signal are difficult to implement because of the high bandwidth and

  7. Enclosure for handling high activity materials

    Energy Technology Data Exchange (ETDEWEB)

    Jimeno de Osso, F.

    1977-07-01

    One of the most important problems that are met at the laboratories producing and handling radioisotopes is that of designing, building and operating enclosures suitable for the safe handling of active substances. With this purpose in mind, an enclosure has been designed and built for handling moderately high activities under a shielding made of 150 mm thick lead. In this report a description is given of those aspects that may be of interest to people working in this field. (Author)

  8. Bandwidth enhancement of MgZnO-based MSM photodetectors by inductive gain peaking

    Science.gov (United States)

    Wang, Ping; Guo, Xinlu; Guo, Lixin; He, Jingfang; Yang, Yintang; Zhang, Zhiyong

    2016-08-01

    For high-speed optical communication applications, the bandwidth of photodetector would be a key limitation. In this work, the bandwidth property of MgZnO-based Metal-Semiconductor-Metal (MSM) photodetector considering RC and transit limitations is investigated on the basis of the series and enhanced gain peaked photodetector circuits proposed by us with different finger widths. To ensure the accuracy of parameters, the high-filed transportation characteristics of MgZnO are investigated by a three-valley ensemble Monte Carlo simulation combined with first principle calculations. The results show that the gain peaking technique, especially the enhanced gain peaking, can improve the bandwidth of MgZnO MSM photodetector to a maximum value of 61.28 GHz, corresponding to a bandwidth enhancement of 49% without undesired effects. Three-dimensional electromagnetic computation is further performed to design and simulate the on-chip-inductor. The value of the simulated inductor is approximately 0.0529 nH, which is in good agreement with the designed value of 0.0569 nH. This work benefits the development of high speed MgZnO MSM photodetector.

  9. Staged optimization algorithms based MAC dynamic bandwidth allocation for OFDMA-PON

    Science.gov (United States)

    Liu, Yafan; Qian, Chen; Cao, Bingyao; Dun, Han; Shi, Yan; Zou, Junni; Lin, Rujian; Wang, Min

    2016-06-01

    Orthogonal frequency division multiple access passive optical network (OFDMA-PON) has being considered as a promising solution for next generation PONs due to its high spectral efficiency and flexible bandwidth allocation scheme. In order to take full advantage of these merits of OFDMA-PON, a high-efficiency medium access control (MAC) dynamic bandwidth allocation (DBA) scheme is needed. In this paper, we propose two DBA algorithms which can act on two different stages of a resource allocation process. To achieve higher bandwidth utilization and ensure the equity of ONUs, we propose a DBA algorithm based on frame structure for the stage of physical layer mapping. Targeting the global quality of service (QoS) of OFDMA-PON, we propose a full-range DBA algorithm with service level agreement (SLA) and class of service (CoS) for the stage of bandwidth allocation arbitration. The performance of the proposed MAC DBA scheme containing these two algorithms is evaluated using numerical simulations. Simulations of a 15 Gbps network with 1024 sub-carriers and 32 ONUs demonstrate the maximum network throughput of 14.87 Gbps and the maximum packet delay of 1.45 ms for the highest priority CoS under high load condition.

  10. Bandwidth auction for SVC streaming in dynamic multi-overlay

    Science.gov (United States)

    Xiong, Yanting; Zou, Junni; Xiong, Hongkai

    2010-07-01

    In this paper, we study the optimal bandwidth allocation for scalable video coding (SVC) streaming in multiple overlays. We model the whole bandwidth request and distribution process as a set of decentralized auction games between the competing peers. For the upstream peer, a bandwidth allocation mechanism is introduced to maximize the aggregate revenue. For the downstream peer, a dynamic bidding strategy is proposed. It achieves maximum utility and efficient resource usage by collaborating with a content-aware layer dropping/adding strategy. Also, the convergence of the proposed auction games is theoretically proved. Experimental results show that the auction strategies can adapt to dynamic join of competing peers and video layers.

  11. Ultra-broad bandwidth parametric amplification at degeneracy.

    Science.gov (United States)

    Limpert, J; Aguergaray, C; Montant, S; Manek-Hönninger, I; Petit, S; Descamps, D; Cormier, E; Salin, F

    2005-09-19

    We report on a novel approach of ultra-broad bandwidth parametric amplification around degeneracy. A bandwidth of up to 400 nm centered around 800 nm is amplified in a BBO crystal by using chirped pump pulses with a bandwitdth as broad as 10 nm. A supercontinuum signal is generated in a microstructured fiber, having to first order a quadratic chirp, which is necessary to ensure temporal overlap of the interacting waves over this broad bandwidth. Furthermore, we discuss the potential of this approach for an octave-spanning parametric amplification.

  12. Energy efficiency in elastic-bandwidth optical networks

    DEFF Research Database (Denmark)

    Vizcaino, Jorge Lopez; Ye, Yabin; Tafur Monroy, Idelfonso

    2011-01-01

    The forecasted growth in the Internet traffic has made the operators and industry to be concerned about the power consumption of the networks, and to become interested in alternatives to plan and operate the networks in a more energy efficient manner. The introduction of OFDM, and its property...... of elastic bandwidth allocation, opens new horizons in the operation of optical networks. In this paper, we compare the network planning problem in an elastic bandwidth CO-OFDM-based network and a fixed-grid WDM network. We highlight the benefits that bandwidth elasticity and the selection of different...

  13. Efficiently parallelized modeling of tightly focused, large bandwidth laser pulses

    Science.gov (United States)

    Dumont, Joey; Fillion-Gourdeau, François; Lefebvre, Catherine; Gagnon, Denis; MacLean, Steve

    2017-02-01

    The Stratton-Chu integral representation of electromagnetic fields is used to study the spatio-temporal properties of large bandwidth laser pulses focused by high numerical aperture mirrors. We review the formal aspects of the derivation of diffraction integrals from the Stratton-Chu representation and discuss the use of the Hadamard finite part in the derivation of the physical optics approximation. By analyzing the formulation we show that, for the specific case of a parabolic mirror, the integrands involved in the description of the reflected field near the focal spot do not possess the strong oscillations characteristic of diffraction integrals. Consequently, the integrals can be evaluated with simple and efficient quadrature methods rather than with specialized, more costly approaches. We report on the development of an efficiently parallelized algorithm that evaluates the Stratton-Chu diffraction integrals for incident fields of arbitrary temporal and spatial dependence. This method has the advantage that its input is the unfocused field coming from the laser chain, which is experimentally known with high accuracy. We use our method to show that the reflection of a linearly polarized Gaussian beam of femtosecond duration off a high numerical aperture parabolic mirror induces ellipticity in the dominant field components and generates strong longitudinal components. We also estimate that future high-power laser facilities may reach intensities of {10}24 {{W}} {{cm}}-2.

  14. Modulation bandwidth enhancement of white-LED-based visible light communications using electrical equalizations

    Science.gov (United States)

    Kwon, D. H.; Yang, S. H.; Han, S. K.

    2015-01-01

    Utilizing the modulation capability of LEDs, there have been many studies about convergence technology to combine illumination and communication. The visible light communication (VLC) system has several advantages such as high security, immunity to RF interference and lower additional cost than comparing to LEDs just for illumination. However, modulation bandwidth of LEDs is not enough for various wireless communication systems. Since the commercial LEDs are designed only for lighting systems; we need an effort to enhance the modulation characteristics of LEDs. When the area of LED is increased, internal junction capacitance of LED is also increased depending on the area of LEDs and then the RC delay time of LED is increased. As a result, the modulation bandwidth of LEDs is limited by large RC delay time. In addition, frequency response of commercial white LED is degraded by the slow response time of the used yellow phosphor. Thus, modulation bandwidth of VLC system is limited to several MHz which is not enough to accommodate high data rate transmission. In this paper, we designed equalization circuit using RLC component for compensating the white LEDs frequency response. Also, we used blue filtering to improve frequency response of white LEDs, which is degraded by yellow phosphorescent component. Power loss by optical filtering and distance is compensated by convex lens. Consequently, we extend the modulation bandwidth of VLC system from 3 MHz to more than 180 MHz, and it allows NRZ-OOK data transmission up to 400 Mbps at 50 cm.

  15. High-activity liquid packaging design criteria

    Energy Technology Data Exchange (ETDEWEB)

    1994-05-01

    In recent studies, it has been acknowledged that there is an emerging need for packaging to transport high-activity liquid off the Hanford Site to support characterization and process development activities of liquid waste stored in underground tanks. These studies have dealt with specimen testing needs primarily at the Hanford Site; however, similar needs appear to be developing at other US Department of Energy (DOE) sites. The need to ship single and multiple specimens to offsite laboratories is anticipated because it is predicted that onsite laboratories will be overwhelmed by an increasing number and size (volume) of samples. Potentially, the specimen size could range from 250 mL to greater than 50 L. Presently, no certified Type-B packagings are available for transport of high-activity liquid radioactive specimens in sizes to support Site missions.

  16. Bandwidth allocation and pricing problem for a duopoly market

    Directory of Open Access Journals (Sweden)

    You Peng-Sheng

    2011-01-01

    Full Text Available This research discusses the Internet service provider (ISP bandwidth allocation and pricing problems for a duopoly bandwidth market with two competitive ISPs. According to the contracts between Internet subscribers and ISPs, Internet subscribers can enjoy their services up to their contracted bandwidth limits. However, in reality, many subscribers may experience the facts that their on-line requests are denied or their connection speeds are far below their contracted speed limits. One of the reasons is that ISPs accept too many subscribers as their subscribers. To avoid this problem, ISPs can set limits for their subscribers to enhance their service qualities. This paper develops constrained nonlinear programming to deal with this problem for two competitive ISPs. The condition for reaching the equilibrium between the two competitive firms is derived. The market equilibrium price and bandwidth resource allocations are derived as closed form solutions.

  17. Available Bandwidth Estimation Strategy Based on the Network Allocation Vector

    Directory of Open Access Journals (Sweden)

    Hongtao Liu

    2012-12-01

    Full Text Available Available bandwidth is of great importance to network Quality of Service assurance, network load balancing, streaming media rate control, routing, and congestion control, etc.. In this paper, the available bandwidth estimation strategy based on the Network Allocation Vector for Wireless Sensor Networks is proposed. According to the size of the average contention window, network nodes predict the probability of collision in process of frame transmission, and then estimate the number of retransmission. Through the collection of Hello packets periodically sent by neighbors, nodes obtain their Network Allocation Vector, and then estimate the available bandwidth. The simulation results show that the strategy is simple and effective, can accurately estimate the collision of data frames as well as the available bandwidth of Wireless Sensor Networks.

  18. Low and Expensive Bandwidth Remains Key Bottleneck for ...

    African Journals Online (AJOL)

    PROF. O. E. OSUAGWU

    2013-06-01

    Jun 1, 2013 ... + Department of Computer Science, Imo State University + South Eastern College of Computer ... The National Communications Commission (NCC) which is the Apex body that .... Low bandwidth slows down data transfer.

  19. An Improved Dynamic Bandwidth Allocation Algorithm for Ethernet PON

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    This paper proposes an improved Dynamic Bandwidth Allocation (DBA) algorithm for EPON, which combines static and traditional dynamic allocation schemes. Simulation result shows that the proposed algorithm may effectively improve the performance of packet delay.

  20. Radiation Bandwidth Improvement of Electromagnetic Band Gap Cavity Antenna

    Science.gov (United States)

    Chaabane, Abdelhalim; Djahli, Farid; Attia, Hussein; Denidni, Tayeb. A.

    2017-09-01

    In this paper, an electromagnetic band gap cavity antenna with improved radiation and impedance bandwidths is presented. The proposed antenna is constructed by placing a triple-layer heterogeneous printed-unprinted partially reflective surface (PRS) above a primary aperture-coupled patch antenna. The PRS unit-cell provides a positive gradient reflection phase behavior over the desired frequency range. A prototype antenna is fabricated and measured that highlighted its ability to achieve 3-dB gain bandwidth of about 35.9 %, from 7.93 GHz to 11.4 GHz, with a peak gain of 14.25 dBi at 8.5 GHz. In addition, the impedance bandwidth is 40.32 %, from 7.9 GHz to 11.89 GHz. Thus, the designed antenna outperforms many other competitors for improving the radiation bandwidth of planar antennas with the same presented concept.

  1. MULTILAYER MICROSTRIP ANTENNA QUALITY FACTOR OPTIMIZATION FOR BANDWIDTH ENHANCEMENT

    Directory of Open Access Journals (Sweden)

    M.C. SRIVASTAVA

    2012-12-01

    Full Text Available The impedance bandwidth, one of the important characteristics of microstrip patch antennas, can be significantly improved by using a multilayer dielectric configuration. In this paper the focus is on bandwidth enhancement technique of a multilayer patch antenna for X-band applications. In order to enhance the bandwidth, antenna losses are contained by controlling those quality factors which can have a significant impact on the bandwidth for a given permittivity and thickness of the substrate. This has been achieved by conformal transformation of the multidielectric microstrip antenna. For the ease of analysis Wheelers transformation is used to map the complex permittivity of a multilayer substrate to a single layer. Method of Moments and Finite Difference Time Domain approaches are used for the computation of results.

  2. Bandwidth Estimation in Wireless Lans for Multimedia Streaming Services

    Directory of Open Access Journals (Sweden)

    Heung Ki Lee

    2007-01-01

    Full Text Available The popularity of multimedia streaming services via wireless networks presents major challenges in the management of network bandwidth. One challenge is to quickly and precisely estimate the available bandwidth for the decision of streaming rates of layered and scalable multimedia services. Previous studies based on wired networks are too burdensome to be applied to multimedia applications in wireless networks. In this paper, a new method, IdleGap, is suggested to estimate the available bandwidth of a wireless LAN based on the information from a low layer in the protocol stack. We use a network simulation tool, NS-2, to evaluate our new method with various ranges of cross-traffic and observation times. Our simulation results show that IdleGap accurately estimates the available bandwidth for all ranges of cross-traffic (100 Kbps ∼ 1 Mbps with a very short observation time of 10 seconds.

  3. High activity carbon sorbents for mercury capture

    Energy Technology Data Exchange (ETDEWEB)

    George G. Stavropoulos; Irene S. Diamantopoulou; George E. Skodras; George P. Sakellaropoulos [Aristotle University of Thessaloniki, Thessaloniki (Greece). Chemical Process Engineering Laboratory

    2006-07-01

    High efficiency activated carbons have been prepared for removing mercury from gas streams. Starting materials used were petroleum coke, lignite, charcoal and olive seed waste, and were chemically activated with KOH. Produced adsorbents were primarily characterized for their porosity by N{sub 2} adsorption at 77K. Their mercury retention capacity was characterized based on the breakthrough curves. Compared with typical commercial carbons, they have exhibited considerably enhanced mercury adsorption capacity. An attempt has been made to correlate mercury entrapment and pore structure. It has been shown that physical surface area is increased during activation in contrast to the mercury adsorption capacity that initially increases and tends to decrease at latter stages. Desorption of active sites may be responsible for this behavior. 10 refs., 3 figs., 1 tab.

  4. Laser frequency bandwidth narrowing by photorefractive two-beam coupling.

    Science.gov (United States)

    Chomsky, D; Sternklar, S; Zigler, A; Jackel, S

    1992-04-01

    We present a theoretical analysis and experimental demonstration of a new method for spectral narrowing of laser radiation. The bandwidth narrowing is experienced by a laser beam subjected to a photorefractive two-beam coupling process. Contrary to the conventional method of frequency filtering by a Fabry-Perot étalon, this technique has no intrinsic finesse limitation on its resolution. A factor of 2 in frequency bandwidth narrowing is achieved with an argon-ion laser.

  5. Lightweight monitoring of label switched paths for bandwidth management

    OpenAIRE

    Vilà Talleda, Pere; Marzo i Lázaro, Josep Lluís; Calle Ortega, Eusebi; Carrillo, Liliana

    2004-01-01

    The purpose of resource management is the efficient and effective use of network resources, for instance bandwidth. In this article, a connection oriented network scenario is considered, where a certain amount of bandwidth is reserved for each label switch path (LSP), which is a logical path, in a MPLS or GMPLS environment. Assuming there is also some kind of admission control (explicit or implicit), these environments typically provide quality of service (QoS) guarantees. It could happen tha...

  6. A meta-substrate to enhance the bandwidth of metamaterials

    OpenAIRE

    Hongsheng Chen; Zuojia Wang; Runren Zhang; Huaping Wang; Shisheng Lin; Faxin Yu; Moser, Herbert O.

    2014-01-01

    We propose the concept of a meta-substrate to broaden the bandwidth of left-handed metamaterials. The meta-substrate, which behaves like an inhomogeneous magnetic substrate, is composed of another kind of magnetic metamaterials like metallic closed rings. When conventional metamaterial rings are printed on this kind of meta-substrate in a proper way, the interaction of the metamaterials units can be greatly enhanced, yielding an increased bandwidth of negative permeability. An equivalent circ...

  7. Bandwidth-Efficient Cooperative Relaying Schemes with Multiantenna Relay

    Directory of Open Access Journals (Sweden)

    Tho Le-Ngoc

    2008-05-01

    Full Text Available We propose coded cooperative relaying schemes in which all successfully decoded signals from multiple sources are forwarded simultaneously by a multiantenna relay to a common multiantenna destination to increase bandwidth efficiency. These schemes facilitate various retransmission strategies at relay and single-user and multiuser iterative decoding techniques at destination, suitable for trade-offs between performance, latency, and complexity. Simulation results show that the proposed schemes significantly outperform direct transmission under the same transmit power and bandwidth efficiency.

  8. Scaling Mesa Indium Phosphide DHBTs to Record Bandwidths

    Science.gov (United States)

    Lobisser, Evan

    Indium phosphide heterojunction bipolar transistors are able to achieve higher bandwidths at a given feature size than transistors in the Silicon material system for a given feature size. Indium phosphide bipolar transistors demonstrate higher breakdown voltages at a given bandwidth than both Si bipolars and field effect transistors in the InP material system. The high bandwidth of InP HBTs results from both intrinsic material parameters and bandgap engineering through epitaxial growth. The electron mobility in the InGaAs base and saturation velocity in the InP collector are both approximately three times higher than their counterparts in the SiGe material system. Resistance of the base can be made very low due to the large offset in the valence band between the InP emitter and the InGaAs base, which allows the base to be doped on the order of 1020 cm-3 with negligible reduction in emitter injection efficiency. This thesis deals with type-I, NPN dual-heterojunction bipolar transistors. The emitters are InP, and the base is InGaAs. There is a thin (˜ 10 nm) n-type InGaAs "setback" region, followed by a chirped superlattice InGaAs/InAlAs grade to the InP collector. The setback, grade, and collector are all lightly doped n-type. The emitter and collector are contacted through thin (˜ 5 nm) heavily doped n-type InGaAs layers to reduce contact resistivity. The primary focus of this work is increasing the bandwidth of InP HBTs through the proportional scaling of the device dimensions, both layer thicknesses and junction areas, as well as the reduction of the contact resistivities associated with the transistor. Essentially, all RC time constants and transit times must be reduced by a factor of two to double a transistor's bandwidth. Chapter 2 describes in detail the scaling laws and design principles for high frequency bipolar transistor design. A low-stress, blanket sputter deposited composite emitter metal process was developed. Refractory metal base contacts were

  9. Bandwidth Dependence of Laser Plasma Instabilities Driven by the Nike KrF Laser

    Science.gov (United States)

    Weaver, J. L.; Oh, J.; Seely, J.; Kehne, D.; Brown, C. M.; Obenschain, S.; Serlin, V.; Schmitt, A. J.; Phillips, L.; Lehmberg, R. H.; McLean, E.; Manka, C.; Feldman, U.

    2011-10-01

    The Nike krypton-fluoride (KrF) laser at the Naval Research Laboratory operates in the deep UV (248 nm) and employs beam smoothing by induced spatial incoherence (ISI). In the first ISI studies at longer wavelengths (1054 nm and 527 nm) [Obenschain, PRL 62, 768(1989);Mostovych, PRL, 59, 1193(1987); Peyser, Phys. Fluids B 3, 1479(1991)], stimulated Raman scattering, stimulated Brillouin scattering, and the two plasmon decay instability were reduced when wide bandwidth ISI (δν / ν ~ 0.03-0.19%) pulses irradiated targets at moderate to high intensities (1014-1015W/cm2) . Recent Nike work showed that the threshold for quarter critical instabilities increased with the expected wavelength scaling, without accounting for the large bandwidth (δν ~ 1-3 THz). New experiments will compare laser plasma instabilities (LPI) driven by narrower bandwidth pulses to those observed with the standard operation. The bandwidth of KrF lasers can be reduced by adding narrow filters (etalons or gratings) in the initial stages of the laser. This talk will discuss the method used to narrow the output spectrum of Nike, the laser performance for this new operating mode, and target observations of LPI in planar CH targets. Work supported by DoE/NNSA.

  10. Note: Expanding the bandwidth of the ultra-low current amplifier using an artificial negative capacitor

    Energy Technology Data Exchange (ETDEWEB)

    Xie, Kai, E-mail: kaixie@mail.xidian.edu.cn; Liu, Yan; Li, XiaoPing [School of Aerospace Science and Technology, Xidian University, Xi’an 710071 (China); Guo, Lixin [School of Physics and Optoelectronic Engineering, Xidian University, Xi’an 710071 (China); Zhang, Hanlu [School of Communication & Information Engineering, Xi’an University of Posts & Telecommunication, Xi’an 710121 (China)

    2016-04-15

    The bandwidth and low noise characteristics are often contradictory in ultra-low current amplifier, because an inevitable parasitic capacitance is paralleled with the high value feedback resistor. In order to expand the amplifier’s bandwidth, a novel approach was proposed by introducing an artificial negative capacitor to cancel the parasitic capacitance. The theory of the negative capacitance and the performance of the improved amplifier circuit with the negative capacitor are presented in this manuscript. The test was conducted by modifying an ultra-low current amplifier with a trans-impedance gain of 50 GΩ. The results show that the maximum bandwidth was expanded from 18.7 Hz to 3.3 kHz with more than 150 times of increase when the parasitic capacitance (∼0.17 pF) was cancelled. Meanwhile, the rise time decreased from 18.7 ms to 0.26 ms with no overshot. Any desired bandwidth or rise time within these ranges can be obtained by adjusting the ratio of cancellation of the parasitic and negative capacitance. This approach is especially suitable for the demand of rapid response to weak current, such as transient ion-beam detector, mass spectrometry analysis, and fast scanning microscope.

  11. On the Problem of Bandwidth Partitioning in FDD Block-Fading Single-User MISO/SIMO Systems

    Directory of Open Access Journals (Sweden)

    Josef A. Nossek

    2008-10-01

    Full Text Available We report on our research activity on the problem of how to optimally partition the available bandwidth of frequency division duplex, multi-input single-output communication systems, into subbands for the uplink, the downlink, and the feedback. In the downlink, the transmitter applies coherent beamforming based on quantized channel information which is obtained by feedback from the receiver. As feedback takes away resources from the uplink, which could otherwise be used to transfer payload data, it is highly desirable to reserve the “right” amount of uplink resources for the feedback. Under the assumption of random vector quantization, and a frequency flat, independent and identically distributed block-fading channel, we derive closed-form expressions for both the feedback quantization and bandwidth partitioning which jointly maximize the sum of the average payload data rates of the downlink and the uplink. While we do introduce some approximations to facilitate mathematical tractability, the analytical solution is asymptotically exact as the number of antennas approaches infinity, while for systems with few antennas, it turns out to be a fairly accurate approximation. In this way, the obtained results are meaningful for practical communication systems, which usually can only employ a few antennas.

  12. Bandwidth Reduction and Convergence Analysis of Extremum Seeking Control with Feedback Encoding

    Directory of Open Access Journals (Sweden)

    Vikum Sri Wijesinghe

    2016-11-01

    Full Text Available Frequently a physical plant of a control system has an optimum operating point such as the spark (or injection time of an internal combustion engine that results in maximum torque. Extremum Seeking Control (ESC is a method of adaptive control capable of locating and maintaining a plant at such an optimum operating point in real time. It is capable of doing so with minimal a priori knowledge of the plant and can also track slowly varying changes. Input perturbed ESC schemes that use periodic dither signals have the disadvantage of requiring a high bandwidth for sampling and correlating the plant output with the dither signal. If the feedback path were to be implemented over a packet switched communication network, the high bandwidth requirement could result in increased congestion and consequently packet delays and dropouts. As a solution encoding using sporadic (aperiodic sampling techniques can be used in the feedback path of the ESC scheme to reduce the required bandwidth. However, in order to ensure convergence of the ESC scheme with encoding, the effect of the signal reconstruction error due to encoding on the critical correlation stage has to be investigated. The contribution of this paper is an investigation of the convergence requirements and bandwidth performance of two encoding schemes; Memory Based Event Triggering (MBET and Event Triggered Adaptive Differential Modulation (ETADM. The results show that MBET can fail for objective functions with plateaus. ETADM fails when the number of ETADM steps used for reconstructing the plant output per perturbation cycle are too low to allow correlation. In terms of bandwidth reduction MBET performs better than ETADM (97% and 70% respectively. However, the use of MBET results in a longer convergence time.

  13. Production of high specific activity silicon-32

    Energy Technology Data Exchange (ETDEWEB)

    Phillips, D.R. [Los Alamos National Lab., NM (United States); Brzezinski, M.A. [Univ. of California, Santa Barbara, CA (United States). Marine Biotechnology Center

    1998-12-31

    This is the final report of a three-year, Laboratory Directed Research and Development Project (LDRD) at Los Alamos National Laboratory (LANL). There were two primary objectives for the work performed under this project. The first was to take advantage of capabilities and facilities at Los Alamos to produce the radionuclide {sup 32}Si in unusually high specific activity. The second was to combine the radioanalytical expertise at Los Alamos with the expertise at the University of California to develop methods for the application of {sup 32}Si in biological oceanographic research related to global climate modeling. The first objective was met by developing targetry for proton spallation production of {sup 32}Si in KCl targets and chemistry for its recovery in very high specific activity. The second objective was met by developing a validated field-useable, radioanalytical technique, based upon gas-flow proportional counting, to measure the dynamics of silicon uptake by naturally occurring diatoms.

  14. Active vibration isolation of high precision machines

    CERN Document Server

    Collette, C; Artoos, K; Hauviller, C

    2010-01-01

    This paper provides a review of active control strategies used to isolate high precisionmachines (e.g. telescopes, particle colliders, interferometers, lithography machines or atomic force microscopes) from external disturbances. The objective of this review is to provide tools to develop the best strategy for a given application. Firstly, the main strategies are presented and compared, using single degree of freedom models. Secondly, the case of huge structures constituted of a large number of elements, like particle colliders or segmented telescopes, is considered.

  15. Constant-bandwidth constant-temperature hot-wire anemometer.

    Science.gov (United States)

    Ligeza, P

    2007-07-01

    A constant-temperature anemometer (CTA) enables the measurement of fast-changing velocity fluctuations. In the classical solution of CTA, the transmission band is a function of flow velocity. This is a minor drawback when the mean flow velocity does not significantly change, though it might lead to dynamic errors when flow velocity varies over a considerable range. A modification is outlined, whereby an adaptive controller is incorporated in the CTA system such that the anemometer's transmission band remains constant in the function of flow velocity. For that purpose, a second feedback loop is provided, and the output signal from the anemometer will regulate the controller's parameters such that the transmission bandwidth remains constant. The mathematical model of a CTA that has been developed and model testing data allow a through evaluation of the proposed solution. A modified anemometer can be used in measurements of high-frequency variable flows in a wide range of velocities. The proposed modification allows the minimization of dynamic measurement errors.

  16. Bandwidth control of wavelength-selective uncooled infrared sensors using two-dimensional plasmonic absorbers

    Science.gov (United States)

    Ogawa, Shinpei; Fujisawa, Daisuke; Kimata, Masafumi

    2016-05-01

    Although standard uncooled infrared (IR) sensors can be used to record information such as the shape, position, and average radiant intensity of objects, these devices cannot capture color (that is, wavelength) data. Achieving wavelength selectivity would pave the way for the development of advanced uncooled IR sensors capable of providing color information as well as multi-color image sensors that would have significant advantages in applications such as fire detection, gas analysis, hazardous material recognition, and biological analysis. We have previously demonstrated an uncooled IR sensor incorporating a two-dimensional plasmonic absorber (2D PLA) that exhibits wavelength selectivity over a wide range in the mid- and long-IR regions. This PLA has a 2D Au-based periodic array of dimples, in which surface plasmon modes are induced and wavelength-selective absorption occurs. However, the dependence of the absorption bandwidth on certain structural parameters has yet to be clarified. The bandwidth of such devices is a vital factor when considering the practical application of these sensors to tasks such as gas detection. In the present study, control of the bandwidth was theoretically investigated using a rigorous coupled wave analysis approach. It is demonstrated that the dimple sidewall structure has a significant impact on the bandwidth and can be used to control both narrow- and broadband absorption. Increasing the sidewall slope was found to decrease the bandwidth due to suppression of cavity-mode resonance in the depth direction of the dimples. These results will contribute to the development of high-resolution, wavelength-selective uncooled IR sensors.

  17. Active Block Layout: A High Performance Block Layout Mechanism%Active Block Layout:一种高性能磁盘布局机制

    Institute of Scientific and Technical Information of China (English)

    卢军; 卢显良; 罗光春; 韩宏; 魏青松

    2003-01-01

    The access frequency of different files in file system is dissimilar. If file system can optimize the block lay-out of these hot files which are frequently accessed,the performance of file system will be improved. This paper pre-sents a high performance block layout mechanism: Active Block Layout (ABL). ABL can record the access frequencyof every file in file system and actively optimize the block layout of these hot files by block duplicating. The duplicatedblocks can be placed in the special zone of track,which is called "Cooling Zone". ABL can automatically determine theplacing position and the copy count of the blocks which need to be duplicated. In order to reduce the overhead of blockduplication,this paper also presents a mechanism which uses the potential disk bandwidth to realize the block duplica-tion,and does not obviously degrade the performance of file system.

  18. Effective bandwidth guaranteed routing schemes for MPLS traffic engineering

    Science.gov (United States)

    Wang, Bin; Jain, Nidhi

    2001-07-01

    In this work, we present online algorithms for dynamic routing bandwidth guaranteed label switched paths (LSPs) where LSP set-up requests (in terms of a pair of ingress and egress routers as well as its bandwidth requirement) arrive one by one and there is no a priori knowledge regarding future LSP set-up requests. In addition, we consider rerouting of LSPs in this work. Rerouting of LSPs has not been well studied in previous work on LSP routing. The need of LSP rerouting arises in a number of ways: occurrence of faults (link and/or node failures), re-optimization of existing LSPs' routes to accommodate traffic fluctuation, requests with higher priorities, and so on. We formulate the bandwidth guaranteed LSP routing with rerouting capability as a multi-commodity flow problem. The solution to this problem is used as the benchmark for comparing other computationally less costly algorithms studied in this paper. Furthermore, to more efficiently utilize the network resources, we propose online routing algorithms which route bandwidth demands over multiple paths at the ingress router to satisfy the customer requests while providing better service survivability. Traffic splitting and distribution over the multiple paths are carefully handled using table-based hashing schemes while the order of packets within a flow is preserved. Preliminary simulations are conducted to show the performance of different design choices and the effectiveness of the rerouting and multi-path routing algorithms in terms of LSP set-up request rejection probability and bandwidth blocking probability.

  19. Open-Loop Wide-Bandwidth Phase Modulation Techniques

    Directory of Open Access Journals (Sweden)

    Nitin Nidhi

    2011-01-01

    Full Text Available The ever-increasing growth in the bandwidth of wireless communication channels requires the transmitter to be wide-bandwidth and power-efficient. Polar and outphasing transmitter topologies are two promising candidates for such applications, in future. Both these architectures require a wide-bandwidth phase modulator. Open-loop phase modulation presents a viable solution for achieving wide-bandwidth operation. An overview of prior art and recent approaches for phase modulation is presented in this paper. Phase quantization noise cancellation was recently introduced to lower the out-of-band noise in a digital phase modulator. A detailed analysis on the impact of timing and quantization of the cancellation signal is presented. Noise generated by the transmitter in the receive band frequency poses another challenge for wide-bandwidth transmitter design. Addition of a noise transfer function notch, in a digital phase modulator, to reduce the noise in the receive band during phase modulation is described in this paper.

  20. High Energy Activation Data Library (HEAD-2009)

    CERN Document Server

    Korovin, Yury A; Konobeyev, Alexander Yu; Stankovskiy, Alexey Yu; Mashnik, Stepan G

    2010-01-01

    A proton activation data library for 682 nuclides from 1-H to 210-Po in the energy range from 150 MeV up to 1 GeV was developed. To calculate proton activation data, the MCNPX 2.6.0 and CASCADE/INPE codes were chosen. Different intranuclear cascade, preequilibrium, and equilibrium nuclear reaction models and their combinations were used. The optimum calculation models have been chosen on the basis of statistical correlations for calculated and experimental proton data taken from the EXFOR library of experimental nuclear data. All the data are written in ENDF-6 format. The library is called HEPAD-2008 (High-Energy Proton Activation Data). A revision of IEAF-2005 neutron activation data library has been performed: A set of nuclides for which the cross-section data can be (and were) updated using more modern and improved models is specified, and the corresponding calculations have been made in the present work. The new version of the library is called IEAF-2009. The HEPAD-2008 and IEAF-2009 are merged to the fin...

  1. High bandwidth on-chip capacitive tuning of microtoroid resonators

    CERN Document Server

    Baker, Christopher G; McAuslan, David L; Sheridan, Eoin; Bowen, Warwick P

    2016-01-01

    We report on the design, fabrication and characterization of silica microtoroid based cavity opto-electromechanical systems (COEMS). Electrodes patterned onto the microtoroid resonators allow for rapid capacitive tuning of the optical whispering gallery mode resonances while maintaining their ultrahigh quality factor, enabling applications such as efficient radio to optical frequency conversion, optical routing and switching applications.

  2. High bandwidth synaptic communication and frequency tracking in human neocortex

    NARCIS (Netherlands)

    Testa-Silva, Guilherme; Verhoog, Matthijs B; Linaro, Daniele; de Kock, Christiaan P J; Baayen, Johannes C; Meredith, Rhiannon M; De Zeeuw, Chris I; Giugliano, Michele; Mansvelder, Huibert D

    2014-01-01

    Neuronal firing, synaptic transmission, and its plasticity form the building blocks for processing and storage of information in the brain. It is unknown whether adult human synapses are more efficient in transferring information between neurons than rodent synapses. To test this, we recorded from c

  3. Wide bandwidth high efficiency power converter for rf amplifiers

    OpenAIRE

    Vasic, Miroslav

    2011-01-01

    Tradicionalmente, en el mundo de la amplificación de potencia de alta frecuencia, se han distinguido dos grandes familias de amplificadores de potencia, atendiendo al efecto de su utilización sobre las señales amplificadas por los mismos: lineales y no lineales. Los amplificadores lineales se han relacionado con las clases de amplificación A, B y AB generalmente poco eficaces en el aprovechamiento de la energía, mientras que los amplificadores no lineales se han asociado a clases de funcionam...

  4. Design of application specific high bandwidth Nyquist DAC

    NARCIS (Netherlands)

    Zhijun, Wei

    2008-01-01

    Digital-to-analog (DAC) converters translate digital codes into different physical quantities in voltage, current or charges. They are used either as a stand alone functional block in a big system or as a subsystem in analog-to-digital (ADC) converters. The DAC in this project is a subsystem in a tw

  5. High speed, real-time, camera bandwidth converter

    Science.gov (United States)

    Bower, Dan E; Bloom, David A; Curry, James R

    2014-10-21

    Image data from a CMOS sensor with 10 bit resolution is reformatted in real time to allow the data to stream through communications equipment that is designed to transport data with 8 bit resolution. The incoming image data has 10 bit resolution. The communication equipment can transport image data with 8 bit resolution. Image data with 10 bit resolution is transmitted in real-time, without a frame delay, through the communication equipment by reformatting the image data.

  6. Modulated method for efficient, narrow-bandwidth, laser Compton X-ray and gamma-ray sources

    Energy Technology Data Exchange (ETDEWEB)

    Barty, Christopher P. J.

    2017-07-11

    A method of x-ray and gamma-ray generation via laser Compton scattering uses the interaction of a specially-formatted, highly modulated, long duration, laser pulse with a high-frequency train of high-brightness electron bunches to both create narrow bandwidth x-ray and gamma-ray sources and significantly increase the laser to Compton photon conversion efficiency.

  7. Cascaded passive silicon microrings for large bandwidth slow light device

    Energy Technology Data Exchange (ETDEWEB)

    Li Yuntao; Hu Yingtao; Xiao Xi; Li Zhiyong; Yu Yude; Yu Jinzhong, E-mail: ytli@semi.ac.cn [State Key Laboratory of integrated Optoelectronics, Institute of Semiconductors, Chinese Academy of Sciences, P. O. Box 912, Beijing 100083 (China)

    2011-02-01

    Slow light devices have important applications in the areas of data buffering, signal processing, and phased array antenna. Cascaded microring resonators structure can obtain large delay and also enhance the bandwidth, which was considered as a potential approach for future on-chip optical buffer. In this paper, we demonstrated a large bandwidth slow light device using cascaded Silicon-on-insulator (SOI) based microring resonators. With carefully designed the gap between the bus and the ring waveguides and the distances between the adjacent rings, a 57 ps group delay was observed and 83 Gbps maximum allowable bit rate is suggested according the measured 3 dB spectral bandwidth in the 8-stage cascaded microrings.

  8. Correlation and image compression for limited-bandwidth CCD.

    Energy Technology Data Exchange (ETDEWEB)

    Thompson, Douglas G.

    2005-07-01

    As radars move to Unmanned Aerial Vehicles with limited-bandwidth data downlinks, the amount of data stored and transmitted with each image becomes more significant. This document gives the results of a study to determine the effect of lossy compression in the image magnitude and phase on Coherent Change Detection (CCD). We examine 44 lossy compression types, plus lossless zlib compression, and test each compression method with over 600 CCD image pairs. We also derive theoretical predictions for the correlation for most of these compression schemes, which compare favorably with the experimental results. We recommend image transmission formats for limited-bandwidth programs having various requirements for CCD, including programs which cannot allow performance degradation and those which have stricter bandwidth requirements at the expense of CCD performance.

  9. Bandwidth Extension of Speech Signals: A Comprehensive Review

    Directory of Open Access Journals (Sweden)

    N.Prasad

    2016-02-01

    Full Text Available Telephone systems commonly transmit narrowband (NB speech with an audio bandwidth limited to the traditional telephone band of 300-3400 Hz. To improve the quality and intelligibility of speech degraded by narrow bandwidth, researchers have tried to standardize the telephonic networks by introducing wideband (50-7000 Hz speech codecs. Wideband (WB speech transmission requires the transmission network and terminal devices at both ends to be upgraded to the wideband that turns out to be time-consuming. In this situation, novel Bandwidth extension (BWE techniques have been developed to overcome the limitations of NB speech. This paper discusses the basic principles, realization, and applications of BWE. Challenges and limitations of BWE are also addressed.

  10. Performance Investigation of Virtual Private Networks with Different Bandwidth Allocations

    Directory of Open Access Journals (Sweden)

    Ramaswamy Muthiah

    2010-01-01

    Full Text Available A Virtual Private Network (VPN provides private network connections over a publicly accessible shared network. The effective allocation of bandwidth for VPNs assumes significance in the present scenario due to varied traffic. Each VPN endpoint specifies bounds on the total amount of traffic that it is likely to send or receive at any time. The network provider tailors the VPN so that there is sufficient bandwidth for any traffic matrix that is consistent with these bounds. The approach incorporates the use of Ad-hoc On demand Distance Vector (AODV protocol, with a view to accomplish an enhancement in the performance of the mobile networks. The NS2 based simulation results are evaluated in terms of its metrics for different bandwidth allocations, besides analyzing its performance in the event of exigencies such as link failures. The results highlight the suitability of the proposed strategy in the context of real time applications.

  11. PRIORITY BASED BANDWIDTH ALLOCATION IN WIRELESS SENSOR NETWORKS

    Directory of Open Access Journals (Sweden)

    Mary Cherian

    2014-12-01

    Full Text Available Most of the sensor network applications need real time communication and the need for deadline aware real time communication is becoming eminent in these applications. These applications have different dead line requirements also. The real time applications of wireless sensor networks are bandwidth sensitive and need higher share of bandwidth for higher priority data to meet the dead line requirements. In this paper we focus on the MAC layer modifications to meet the real time requirements of different priority data. Bandwidth partitioning among different priority transmissions is implemented through MAC layer modifications. The MAC layer implements a queuing model that supports lower transfer rate for lower priority packets and higher transfer rate for real time packets with higher priority, minimizing the end to end delay. The performance of the algorithm is evaluated with varying node distribution.

  12. Analysis of bandwidth measurement methodologies over WLAN systems

    CERN Document Server

    Portoles-Comeras, Marc; Mangues-Bafalluy, Josep; Domingo-Pascual, Jordi

    2009-01-01

    WLAN devices have become a fundamental component of nowadays network deployments. However, even though traditional networking applications run mostly unchanged over wireless links, the actual interaction between these applications and the dynamics of wireless transmissions is not yet fully understood. An important example of such applications are bandwidth estimation tools. This area has become a mature research topic with well-developed results. Unfortunately recent studies have shown that the application of these results to WLAN links is not straightforward. The main reasons for this is that the assumptions taken to develop bandwidth measurements tools do not hold any longer in the presence of wireless links (e.g. non-FIFO scheduling). This paper builds from these observations and its main goal is to analyze the interaction between probe packets and WLAN transmissions in bandwidth estimation processes. The paper proposes an analytical model that better accounts for the particularities of WLAN links. The mod...

  13. Adaptive broadcasting mechanism for bandwidth allocation in mobile services.

    Science.gov (United States)

    Horng, Gwo-Jiun; Wang, Chi-Hsuan; Chou, Chih-Lun

    2014-01-01

    This paper proposes a tree-based adaptive broadcasting (TAB) algorithm for data dissemination to improve data access efficiency. The proposed TAB algorithm first constructs a broadcast tree to determine the broadcast frequency of each data and splits the broadcast tree into some broadcast wood to generate the broadcast program. In addition, this paper develops an analytical model to derive the mean access latency of the generated broadcast program. In light of the derived results, both the index channel's bandwidth and the data channel's bandwidth can be optimally allocated to maximize bandwidth utilization. This paper presents experiments to help evaluate the effectiveness of the proposed strategy. From the experimental results, it can be seen that the proposed mechanism is feasible in practice.

  14. A novel dynamic wavelength bandwidth allocation scheme over OFDMA PONs

    Science.gov (United States)

    Yan, Bo; Guo, Wei; Jin, Yaohui; Hu, Weisheng

    2011-12-01

    With rapid growth of Internet applications, supporting differentiated service and enlarging system capacity have been new tasks for next generation access system. In recent years, research in OFDMA Passive Optical Networks (PON) has experienced extraordinary development as for its large capacity and flexibility in scheduling. Although much work has been done to solve hardware layer obstacles for OFDMA PON, scheduling algorithm on OFDMA PON system is still under primary discussion. In order to support QoS service on OFDMA PON system, a novel dynamic wavelength bandwidth allocation (DWBA) algorithm is proposed in this paper. Per-stream QoS service is supported in this algorithm. Through simulation, we proved our bandwidth allocation algorithm performs better in bandwidth utilization and differentiate service support.

  15. Maximum bandwidth snapshot channeled imaging polarimeter with polarization gratings

    Science.gov (United States)

    LaCasse, Charles F.; Redman, Brian J.; Kudenov, Michael W.; Craven, Julia M.

    2016-05-01

    Compact snapshot imaging polarimeters have been demonstrated in literature to provide Stokes parameter estimations for spatially varying scenes using polarization gratings. However, the demonstrated system does not employ aggressive modulation frequencies to take full advantage of the bandwidth available to the focal plane array. A snapshot imaging Stokes polarimeter is described and demonstrated through results. The simulation studies the challenges of using a maximum bandwidth configuration for a snapshot polarization grating based polarimeter, such as the fringe contrast attenuation that results from higher modulation frequencies. Similar simulation results are generated and compared for a microgrid polarimeter. Microgrid polarimeters are instruments where pixelated polarizers are superimposed onto a focal plan array, and this is another type of spatially modulated polarimeter, and the most common design uses a 2x2 super pixel of polarizers which maximally uses the available bandwidth of the focal plane array.

  16. Design optimization of the distributed modal filtering rod fiber for increasing single mode bandwidth

    DEFF Research Database (Denmark)

    Jørgensen, Mette Marie; Petersen, Sidsel Rübner; Laurila, Marko;

    2012-01-01

    . Large preform tolerances are compensated during the fiber draw resulting in ultra low NA fibers with very large cores. In this paper, design optimization of the SM bandwidth of the DMF rod fiber is presented. Analysis of band gap properties results in a fourfold increase of the SM bandwidth compared......High-power fiber amplifiers for pulsed applications require large mode area (LMA) fibers having high pump absorption and near diffraction limited output. This improves the limiting factor of nonlinear effects, while maintaining good beam quality. Photonic crystal fibers allow realization of short...... to previous results, achieved by utilizing the first band of cladding modes. This covers of a large fraction of the Yb emission band, where wavelengths of 1030 nm and 1064 nm can be included....

  17. Influence of Reduced Graphene Oxide on Effective Absorption Bandwidth Shift of Hybrid Absorbers.

    Directory of Open Access Journals (Sweden)

    Shahid Ameer

    Full Text Available The magnetic nanoparticle composite NiFe2O4 has traditionally been studied for high-frequency microwave absorption with marginal performance towards low-frequency radar bands (particularly L and S bands. Here, NiFe2O4 nanoparticles and nanohybrids using large-diameter graphene oxide (GO sheets are prepared via solvothermal synthesis for low-frequency wide bandwidth shielding (L and S radar bands. The synthesized materials were characterized using XRD, SEM, FTIR and microwave magneto dielectric spectroscopy. The dimension of these solvothermally synthesized pristine particles and hybrids lies within 30-58 nm. Microwave magneto-dielectric spectroscopy was performed in the low-frequency region in the 1 MHz-3 GHz spectrum. The as-synthesized pristine nanoparticles and hybrids were found to be highly absorbing for microwaves throughout the L and S radar bands ( 4 GHz with limited selective bandwidth.

  18. Narrow bandwidth Thomson photon source development using Laser-Plasma Accelerators

    Science.gov (United States)

    Geddes, C. G. R.; van Tilborg, J.; Tsai, H.-E.; Toth, Cs.; Vay, J.-L.; Lehe, R.; Schroeder, C. B.; Esarey, E.; Rykovanov, S. G.; Grote, D. P.; Friedman, A.; Leemans, W. P.

    2016-10-01

    Compact, high-quality photon sources at MeV energies are being developed based on Laser-Plasma Accelerators (LPAs). An independent scattering laser with controlled pulse shaping in frequency and amplitude can be used together with laser guiding to realize high photon yield and narrow bandwidth. Simulations are presented on production of controllable narrow bandwidth sources using the beam and plasma capabilities of LPAs. Recent experiments and simulations demonstrate controllable LPAs in the energy range appropriate to MeV Thomson sources. Design of experiments and laser capabilities to combine these elements will be presented, towards a compact photon source system. A dedicated facility under construction will be described. Work supported by US DOE NNSA DNN R&D and by Sc. HEP under contract DE-AC02-05CH11231.

  19. Programmable bandwidth management in software-defined EPON architecture

    Science.gov (United States)

    Li, Chengjun; Guo, Wei; Wang, Wei; Hu, Weisheng; Xia, Ming

    2016-07-01

    This paper proposes a software-defined EPON architecture which replaces the hardware-implemented DBA module with reprogrammable DBA module. The DBA module allows pluggable bandwidth allocation algorithms among multiple ONUs adaptive to traffic profiles and network states. We also introduce a bandwidth management scheme executed at the controller to manage the customized DBA algorithms for all date queues of ONUs. Our performance investigation verifies the effectiveness of this new EPON architecture, and numerical results show that software-defined EPONs can achieve less traffic delay and provide better support to service differentiation in comparison with traditional EPONs.

  20. Modeling of Bandwidth Aggregation over Heterogeneous Wireless Access Networks

    DEFF Research Database (Denmark)

    Popovska Avramova, Andrijana; Dittmann, Lars

    2012-01-01

    Motivated by the multihomming capability of the mobile devices and the fact that the heterogeneous wireless access networks overlap in coverage, mobile operators are looking for solutions that will benefit by simultaneous use of the available multiple access interfaces. Multipath or multilink...... transfer deals with the problem on how to effectively aggregate the bandwidth by simultaneous usage of heterogeneous networks that a host is attached to in order to improve the throughput. This paper deals with a simulation based analysis of bandwidth aggregation techniques and their impact on higher layer...

  1. A meta-substrate to enhance the bandwidth of metamaterials.

    Science.gov (United States)

    Chen, Hongsheng; Wang, Zuojia; Zhang, Runren; Wang, Huaping; Lin, Shisheng; Yu, Faxin; Moser, Herbert O

    2014-06-12

    We propose the concept of a meta-substrate to broaden the bandwidth of left-handed metamaterials. The meta-substrate, which behaves like an inhomogeneous magnetic substrate, is composed of another kind of magnetic metamaterials like metallic closed rings. When conventional metamaterial rings are printed on this kind of meta-substrate in a proper way, the interaction of the metamaterials units can be greatly enhanced, yielding an increased bandwidth of negative permeability. An equivalent circuit analytical model is used to quantitatively characterize this phenomenon. Both numerical and experimental demonstrations are carried out, showing good agreement with theoretical predictions.

  2. Extending the Bandwidth of Electric Ring Resonator Metamaterial Absorber

    Institute of Scientific and Technical Information of China (English)

    LUO Hao; WANG Tao; GONG Rong-Zhou; NIE Yan; WANG Xian

    2011-01-01

    An efficient method is proposed to extend the bandwidth of a metamaterial absorber with multi-resonance structure. The basic unit cell of a metamaterial absorber consists of the electric ring resonator, dielectric substrate (FR-4)and split-wire. By assembling five sandwiched structures with different geometric dimensions into a unit cell, we obtain the superposition of five different absorption peaks.Finally the bandwidth of metamaterial absorption is extended and the full width at half maximum is up to 1.3 GHz. The simulated and experimental results are consistent.

  3. Theory of polaron bandwidth narrowing in organic molecular crystals

    Science.gov (United States)

    Hannewald, K.; Stojanović, V. M.; Schellekens, J. M.; Bobbert, P. A.; Kresse, G.; Hafner, J.

    2004-02-01

    We present a theoretical description of polaron bandwidth narrowing in organic molecular crystals. Based on a solution of a Holstein-Peierls model for tightly bound electrons interacting with phonons, an explicit expression for the temperature dependence of the electronic bandwidths is found. This formula generalizes the result of Holstein polaron theory by treating local and nonlocal electron-phonon coupling on equal footing. The usefulness of the method is demonstrated by model studies for oligo-acene crystals from which microscopic insight into the relevance of the different coupling mechanisms is obtained.

  4. Enhancing the Bandwidth of Gravitational-Wave Detectors with Unstable Optomechanical Filters.

    Science.gov (United States)

    Miao, Haixing; Ma, Yiqiu; Zhao, Chunnong; Chen, Yanbei

    2015-11-20

    Advanced interferometric gravitational-wave detectors use optical cavities to resonantly enhance their shot-noise-limited sensitivity. Because of positive dispersion of these cavities-signals at different frequencies pick up different phases, there is a tradeoff between the detector bandwidth and peak sensitivity, which is a universal feature for quantum measurement devices having resonant cavities. We consider embedding an active unstable filter inside the interferometer to compensate the phase, and using feedback control to stabilize the entire system. We show that this scheme in principle can enhance the bandwidth without sacrificing the peak sensitivity. However, the unstable filter under our current consideration is a cavity-assisted optomechanical device operating in the instability regime, and the thermal fluctuation of the mechanical oscillator puts a very stringent requirement on the environmental temperature and the mechanical quality factor.

  5. Mobile-based system for cost-effective e-learning contents delivery in resource and bandwidth constrained learning environments

    Directory of Open Access Journals (Sweden)

    Michael P. J. Mahenge

    2014-12-01

    Full Text Available The advancement in Information and Communication Technologies (ICTs has brought opportunities for the development of Smart Cities. The Smart City uses ICT to enhance performance and wellbeing, to reduce costs and resource consumption, and to engage more effectively and actively with its citizens. In particular, the education sector is adopting new ways of learning in Higher Education Institutions (HEIs through e-learning systems. While these opportunities exist, e-learning content delivery and accessibility in third world countries like Tanzania is still a challenge due to resource and network constrained environments. The challenges include: high cost of bandwidth connection and usage; high dependency on the Internet; limited mobility and portability features; inaccessibility during the offline period and shortage of ICT facilities. In this paper, we investigate the use of mobile technology to sustainably support education and skills development particularly in developing countries. Specifically, we propose a Cost-effective Mobile Based Learning Content Delivery system for resource and network constrained environments. This system can be applied to cost-effectively broaden and support education in many cities around the world, which are approaching the 'Smart City' concept in their own way, even with less available technology infrastructure. Therefore, the proposed solution has the potential to reduce the cost of the bandwidth usage, and cut down the server workload and the Internet usage overhead by synchronizing learning contents from some remote server to a local database in the user’s device for offline use. It will also improve the quality of experience and participation of learners as well as facilitate mobility and portability in learning activities, which also supports the all-compassing learning experience in a Smart City.

  6. Memristor-capacitor passive filters to tune both cut-off frequency and bandwidth

    Science.gov (United States)

    Ali, Shawkat; Hassan, Arshad; Hassan, Gul; Bae, Jinho; Lee, Chong Hyun

    2017-04-01

    In various optical sensor applications, programmable analog filters are desirable to reduce the hardware requirement. Memristor is two state programmable nonvolatile resistor, which has a small size and low power consumption. Using these resistance switching characteristics of a memristor, we propose a novel memristor-capacitor (MC) based printed low pass and high pass filters for analog circuits to achieve tunable cut-off frequencies and bandwidth. The cut-off frequencies of filters are controlled through a memristor state switching (HRS/LRS), whereas the capacitor has a fixed value. The proposed MC filters utilize graphene/poly 4-vinlyphenol (G/PVP) for dielectric layer of capacitors and Graphene Quatum Dots (GQDs)/PVP for an active layer of memristor, and these layers are fabricated on ITO coated flexible PET substrate through electrohydrodynamic (EHD) technique. Both MC filters are designed as parameters of two state memristance and a capacitance. From comparison between designed and fabricated filters, we show that they are matched quite well.

  7. Active inductor shunt peaking in high-speed VCSEL driver design

    CERN Document Server

    Liang, Futian; Hou, Suen; Liu, Chonghan; Liu, Tiankuan; Su, Da-Shung; Teng, Ping-Kun; Xiang, Annie; Ye, Jingbo; Jin, Ge

    2013-01-01

    An all transistor active inductor shunt peaking structure has been used in a prototype of 8-Gbps high-speed VCSEL driver which is designed for the optical link in ATLAS liquid Argon calorimeter upgrade. The VCSEL driver is fabricated in a commercial 0.25-um Silicon-on-Sapphire (SoS) CMOS process for radiation tolerant purpose. The all transistor active inductor shunt peaking is used to overcome the bandwidth limitation from the CMOS process. The peaking structure has the same peaking effect as the passive one, but takes a small area, does not need linear resistors and can overcome the process variation by adjust the peaking strength via an external control. The design has been tapped out, and the prototype has been proofed by the preliminary electrical test results and bit error ratio test results. The driver achieves 8-Gbps data rate as simulated with the peaking. We present the all transistor active inductor shunt peaking structure, simulation and test results in this paper.

  8. Reducing the Disk IO Bandwidth Bottleneck through Fast Floating Point Compression using Accelerators

    Directory of Open Access Journals (Sweden)

    Ajith Padyana

    2014-03-01

    Full Text Available Compute-intensive tasks in high-end high performance computing (HPC systems often generate large amounts of data, especially floating-point data that need to be transmitted over the network. Although computation speeds are very high, the overall performance of these applications is affected by the data transfer overhead. Moreover, as data sets are growing in size rapidly, bandwidth limitations pose a serious bottleneck in several scientific applications. Fast floating point compression can ameliorate the bandwidth limitations. If data is compressed well, then the amount of data transfer is reduced. This reduction in data transfer time comes at the expense of the increased computation required by compression and decompression. It is important for compression and decompression rates to be greater than the network bandwidth; otherwise, it will be faster to transmit uncompressed data directly [1]. Accelerators such as Graphics Processing Units (GPU provide much computational power. In this paper, we show that the computational power of GPUs and CellBE processor can be harnessed to provide sufficiently fast compression and decompression for this approach to be effective for data produced by many practical applications. In particularly, we use Holt`s Exponential smoothing algorithm from time series analysis, and encode the difference between its predictions and the actual data. This yields a lossless compression scheme. We show that it can be implemented efficiently on GPUs and CellBE to provide an effective compression scheme for the purpose of saving on data transfer overheads The primary contribution of this work lies in demonstrating the potential of floating point compression in reducing the I/O bandwidth bottleneck on modern hardware for important classes of scientific applications.

  9. Concrete with Highly Active Rice Husk Ash

    Institute of Scientific and Technical Information of China (English)

    FENG Qing-ge; LIN Qing-yu; YU Qi-jun; ZHAO San-ying; YANG Lu-feng; Shuichi Sugita

    2004-01-01

    The overall aim was to investigate the effect of highly active rice husk ash (RHA) produced by an industrial furnace on some properties of concrete. The strength, pore volume and pore distribution of concrete and the Ca(OH)2 content in concrete were investigated by JIS A 1108 (Method of test for compressive strength of concrete), a mercury instrument porosimeter, and the thermogravimetric analysis, respectively. The results show that,with RHA replacement of cement,the compressive strength of concrete is increased evidently;the average pore radius of concrete is greatly decreased, especially the portion of the pores greater than 20nm in radius is decreased while the amount of smaller pores is increased, and the more the RHA replacement, the less the amount of Ca(OH)2 in concrete. The latter two results are the main reasons for the strength enhancement of concrete.

  10. Improving Sensitivity and Bandwidth of an Atomic Magnetometer using Quantum Non-Demolition Measurement

    Science.gov (United States)

    Shah, Vishal; Vasilakis, Georgios; Romalis, Michael

    2009-05-01

    The fundamental sensitivity of an atomic magnetometer is limited by spin projection noise. In the case of uniform spin relaxation, it is well understood that it is not possible to improve the sensitivity using spin squeezing induced by quantum non-demolition (QND) measurement for measurement time scales longer than spin relaxation time [1, 2]. It is however possible to increase the bandwidth of the magnetometer using QND measurement. Here we experimentally demonstrate, in excellent agreement with the theory, an improvement in the bandwidth of our scalar alkali vapor atomic magnetometer using continuous QND measurement. We also investigate the possibility of improving sensitivity of our magnetometer in the special case in which the spin relaxation is time dependent. The case of time dependent spin relaxation naturally arises in high polarization regime in an alkali-alkali spin-exchange relaxation dominated atomic sample. [1] S. F. Huelga, Phys. Rev. Lett. 79, 3865 -- 3868, 1997. [2] M. Auzinsh, Phys. Rev. Lett. 93, 173002, 2004.

  11. Optimization of Connector Position Offset for Bandwidth Enhancement of a Multimode Optical Fiber Link

    Science.gov (United States)

    Rawat, Banmali

    2000-01-01

    The multimode fiber bandwidth enhancement techniques to meet the Gigabit Ethernet standards for local area networks (LAN) of the Kennedy Space Center and other NASA centers have been discussed. Connector with lateral offset coupling between single mode launch fiber cable and the multimode fiber cable has been thoroughly investigated. An optimization of connector position offset for 8 km long optical fiber link at 1300 nm with 9 micrometer diameter single mode fiber (SMF) and 50 micrometer diameter multimode fiber (MMF) coupling has been obtained. The optimization is done in terms of bandwidth, eye-pattern, and bit pattern measurements. It is simpler, is a highly practical approach and is cheaper as no additional cost to manufacture the offset type of connectors is involved.

  12. Narrow-bandwidth solar upconversion: design principles, efficiency limits, and case studies

    CERN Document Server

    Briggs, Justin A; Dionne, Jennifer A

    2013-01-01

    We employ a detailed balance approach to model a single-junction solar cell with a realistic narrow-band, non-unity-quantum-yield upconverter. As upconverter bandwidths are increased from 0 to 0.5 eV, maximum cell efficiencies increase from the Shockley-Queisser limit of 30.58% to over 43%. Such efficiency enhancements are calculated for upconverters with near-infrared spectral absorption bands, readily accessible with existing upconverters. While our model shows that current bimolecular and lanthanide-based upconverting materials will improve cell efficiencies by <1%, cell efficiencies can increase by several absolute percent with increased upconverter quantum yield - even without an increased absorption bandwidth. By examining the efficiency limits of a highly realistic solar cell-upconverter system, our model provides a platform for optimizing future solar upconverter designs.

  13. Wideband Spectroscopy: The Design and Implementation of a 3 GHz Bandwidth, 8192 Channel, Polyphase Digital Spectrometer

    Science.gov (United States)

    Monroe, Ryan M.

    2011-01-01

    A family of state-of-the-art digital Fourier transform spectrometers has been developed, with a combination of high bandwidth and fine resolution unavailable elsewhere. Analog signals consisting of radiation emitted by constituents in planetary atmospheres or galactic sources are downconverted and subsequently digitized by a pair of interleaved Analog-to-Digital Converters, (ADC). This 6 Gsps (giga-sample per second) digital representation of the analog signal is then processed through an FPGA-based streaming Fast Fourier Transform (FFT), the key development described below. Digital spectrometers have many advantages over previously used analog spectrometers, especially in terms of accuracy and resolution, both of which are particularly important for the type of scientific questions to be addressed with next-generation radiometers. the implementation, results and underlying math for this spectrometer, as well as, potential for future extension to even higher bandwidth, resolution and channel orthogonality, needed to support proposed future advanced atmospheric science and radioastronomy, are discussed.

  14. Broad-Bandwidth FPGA-Based Digital Polyphase Spectrometer

    Science.gov (United States)

    Jamot, Robert F.; Monroe, Ryan M.

    2012-01-01

    With present concern for ecological sustainability ever increasing, it is desirable to model the composition of Earth s upper atmosphere accurately with regards to certain helpful and harmful chemicals, such as greenhouse gases and ozone. The microwave limb sounder (MLS) is an instrument designed to map the global day-to-day concentrations of key atmospheric constituents continuously. One important component in MLS is the spectrometer, which processes the raw data provided by the receivers into frequency-domain information that cannot only be transmitted more efficiently, but also processed directly once received. The present-generation spectrometer is fully analog. The goal is to include a fully digital spectrometer in the next-generation sensor. In a digital spectrometer, incoming analog data must be converted into a digital format, processed through a Fourier transform, and finally accumulated to reduce the impact of input noise. While the final design will be placed on an application specific integrated circuit (ASIC), the building of these chips is prohibitively expensive. To that end, this design was constructed on a field-programmable gate array (FPGA). A family of state-of-the-art digital Fourier transform spectrometers has been developed, with a combination of high bandwidth and fine resolution. Analog signals consisting of radiation emitted by constituents in planetary atmospheres or galactic sources are downconverted and subsequently digitized by a pair of interleaved analog-to-digital converters (ADCs). This 6-Gsps (gigasample per second) digital representation of the analog signal is then processed through an FPGA-based streaming fast Fourier transform (FFT). Digital spectrometers have many advantages over previously used analog spectrometers, especially in terms of accuracy and resolution, both of which are particularly important for the type of scientific questions to be addressed with next-generation radiometers.

  15. 47 CFR 74.535 - Emission and bandwidth.

    Science.gov (United States)

    2010-10-01

    ... bandwidth: As specified by the following equation but in no event less than 50 decibels: A = 35 + 0.8(G − 50) + 10 Log10 B. (Attenuation greater than 80 decibels is not required.) Where: A = Attenuation (in decibels) below the mean output power level. G = Percent removed from the carrier frequency. B =...

  16. Bandwidth trading under misaligned objectives: decentralized measurement-based control

    NARCIS (Netherlands)

    Mandjes, M.R.H.; Ramakrishnan, M.

    2006-01-01

    This paper studies the interplay between a profit-maximizing network and a number of users competing for the finite bandwidth on each link. In our setting, the objectives of the network and the users are ‘misaligned’, in that the prices that optimize the network’s profit do not maximize the aggregat

  17. Optimization of bandwidth in 60^o photonic crystal waveguide bends

    DEFF Research Database (Denmark)

    Xing, P. F.; Borel, Peter Ingo; Frandsen, Lars Hagedorn;

    2005-01-01

    A systematic scheme utilizing 2D and 3D finite-difference time-domain calculations to design 60^o photonic crystal waveguide bends is presented. The method results in an improved transmission bandwidth from 70 to 160 nm in 2D simulations, and from 50 to 100 nm in 3D simulations. The design...

  18. A Preliminary Evaluation of Bandwidth Allocation Model Dynamic Switching

    Directory of Open Access Journals (Sweden)

    Rafael F. Reale

    2014-06-01

    Full Text Available Bandwidth Allocation Models (BAMs are used in order to define Bandwidth Constraints (BCs in a per-class basis for MPLS/DS-TE networks and effectively define how network resources like bandwidth are obtained and shared by applications. The BAMs proposed (MAM – Maximum Allocation Model, RDM – Russian Dolls Model, G-RDM – Generic RDM and AllocTC-Sharing attempt to optimize the use of bandwidth resources on a per-link basis with different allocation and resource sharing characteristics. As such, the adoption of distinct BAMs and/or changes in network resource demands (network traffic profile may result in different network traffic allocation and operational behavior for distinct BAMs. This paper evaluates the resulting network characteristics (li nk utilization, preemption and flows blocking of using BAMs dynamically with different traffic scenarios. In brief, it is investigated the dynamics of BAM switching with distinct traffic scenarios. The paper presents initially the investigated BAMs in relation to their behavior and resource allocation characteristics. Then, distinct BAMs are compared using different traffic scenarios in order to investigate the impact of a dynamic change of the BAM configured in the network. Finally, the paper shows that the adoption of a dynamic BAM allocation strategy may result in benefits for network operation in terms of link utilization, preemption and flows blocking.

  19. The effect of bandwidth in scale-free network traffic

    CERN Document Server

    Hu, M B; Wang, W X; Wu, Q S; Wu, Y H; Hu, Mao-Bin; Jiang, Rui; Wang, Wen-Xu; Wu, Qing-Song; Wu, Yong-Hong

    2006-01-01

    We model information traffic on scale-free networks by introducing the bandwidth as the delivering ability of links. We focus on the effects of bandwidth on the packet delivering ability of the traffic system to better understand traffic dynamic in real network systems. Such ability can be measured by a phase transition from free flow to congestion. Two cases of node capacity C are considered, i.e., C=constant and C is proportional to the node's degree. We figured out the decrease of the handling ability of the system together with the movement of the optimal local routing coefficient $\\alpha_c$, induced by the restriction of bandwidth. Interestingly, for low bandwidth, the same optimal value of $\\alpha_c$ emerges for both cases of node capacity. We investigate the number of packets of each node in the free flow state and provide analytical explanations for the optimal value of $\\alpha_c$. Average packets traveling time is also studied. Our study may be useful for evaluating the overall efficiency of networke...

  20. Characterizing the effective bandwidth of tri-stable energy harvesters

    Science.gov (United States)

    Panyam, Meghashyam; Daqaq, Mohammed F.

    2017-01-01

    Recently, it has been shown that nonlinear vibratory energy harvesters possessing a tri-stable potential function are capable of harvesting energy efficiently over a wider range of frequencies in comparison to harvesters with a double-well potential function. However, the effect of the design parameters of the harvester on the dynamic response and the effective bandwidth of such devices remains uninvestigated. To fill this void, this paper establishes an analytical approach to characterize the effective frequency bandwidth of harvesters that possess a hexic potential energy function. To achieve this goal, the method of multiple scales is utilized to construct analytical solutions describing the amplitude and stability of the intra- and inter-well dynamics of the harvester. Using these solutions, critical bifurcations in the parameter's space are identified and used to define an effective frequency bandwidth of the harvester. The influence of the electric parameters, namely, the time constant ratio (ratio between the period of the mechanical system and the time constant of the harvesting circuit) and the electromechanical coupling, on the effective frequency bandwidth is analyzed. Experimental studies performed on the harvester are presented to validate some of the theoretical findings.

  1. Gain-switched all-fiber laser with narrow bandwidth

    DEFF Research Database (Denmark)

    Larsen, Casper; Giesberts, M.; Nyga, S.;

    2013-01-01

    Gain-switching of a CW fiber laser is a simple and cost-effective approach to generate pulses using an all-fiber system. We report on the construction of a narrow bandwidth (below 0.1 nm) gain-switched fiber laser and optimize the pulse energy and pulse duration under this constraint. The extracted...

  2. Iterative Available Bandwidth Estimation for Mobile Transport Networks

    DEFF Research Database (Denmark)

    Ubeda Castellanos, Carlos; López Villa, Dimas; Teyeb, Oumer Mohammed;

    2007-01-01

    Available bandwidth estimation has lately been proposed to be used for end-to-end resource management in existing and emerging mobile communication systems, whose transport networks could end up being the bottleneck rather than the air interface. Algorithms for admission control, handover and ada...

  3. Frequency Selective Surfaces for extended Bandwidth backing reflector functions

    NARCIS (Netherlands)

    Pasian, M.; Neto, A.; Monni, S.; Ettorre, M.; Gerini, G.

    2008-01-01

    This paper deals with the use of Frequency Selective Surfaces (FSS) to increase the Efficiency × Bandwidth product in Ultra-Wide Band (UWB) antenna arrays whose efficiency is limited by the front-to-back ratio. If the backing reflector is realized in one metal plane solution its location will be sui

  4. BMCloud: Minimizing Repair Bandwidth and Maintenance Cost in Cloud Storage

    Directory of Open Access Journals (Sweden)

    Chao Yin

    2013-01-01

    Full Text Available To protect data in cloud storage, fault tolerance and efficient recovery become very important. Recent studies have developed numerous solutions based on erasure code techniques to solve this problem using functional repairs. However, there are two limitations to address. The first one is consistency since the Encoding Matrix (EM is different among clouds. The other one is repairing bandwidth, which is a concern for most of us. We addressed these two problems from both theoretical and practical perspectives. We developed BMCloud, a new low repair bandwidth, low maintenance cost cloud storage system, which aims to reduce repair bandwidth and maintenance cost. The system employs both functional repair and exact repair while it inherits advantages from the both. We propose the JUDGE_STYLE algorithm, which can judge whether the system should adopt exact repair or functional repair. We implemented a networked storage system prototype and demonstrated our findings. Compared with existing solutions, BMCloud can be used in engineering to save repair bandwidth and degrade maintenance significantly.

  5. A Practical Approach For Excess Bandwidth Distribution for EPONs

    KAUST Repository

    Elrasad, Amr

    2014-03-09

    This paper introduces a novel approach called Delayed Excess Scheduling (DES), which practically reuse the excess bandwidth in EPONs system. DES is suitable for the industrial deployment as it requires no timing constraint and achieves better performance compared to the previously reported schemes.

  6. Assessing Sufficiency and Quality of Bandwidth for Public Libraries

    Directory of Open Access Journals (Sweden)

    John Carlo Bertot

    2007-03-01

    Full Text Available Based on data collected as part of the 2006 Public Libraries and the Internet study, the authors assess the degree to which public libraries provide sufficient and quality bandwidth to support the library’s networked services and resources. The topic is complex due to the arbitrary assignment of a number of kilobytes per second (kbps used to define bandwidth. Such arbitrary definitions to describe bandwidth sufficiency and quality are not useful. Public libraries are indeed connected to the Internet and do provide public-access services and resources. It is, however, time to move beyond connectivity type and speed questions and consider issues of bandwidth sufficiency, quality, and the range of networked services that should be available to the public from public libraries. A secondary, but important issue is the extent to which libraries, particularly in rural areas, have access to broadband telecommunications services.

  7. Modern Fiber Optic Submarine Cable Telecommunication Systems Planning for Explosive Bandwidth Needs at Different Deployment Depths

    Directory of Open Access Journals (Sweden)

    Ahmed Nabih Zaki Rashed

    2012-10-01

    Full Text Available The explosive bandwidth needs, especially in the inter data center market, have pushed transmission data rates to 100 Gbit/sec and beyond. Current terrestrial fibers are inadequate for long haul, high bandwidth deployments. To solve these problems a new fiber is introduced for terrestrial high bandwidth deployments: different polymeric core fibers with enlarged effective area with a significant optical signal to noise ratio improvement over other conventional terrestrial single mode fibers. To ensure the new fiber may be deployed robustly a new coating structure was employed. A rigorous cable structure was then chosen for evaluation. Based on experimental data, both the deep ocean water temperature and pressure are tailored as functions of the water depth. As well as the product of the transmitted bit rate and the repeater spacing is processed over wide ranges of the affecting parameters. It is taken into account the estimation of the total cost of the submarine fiber cable system for transmission technique under considerations. The system capacity as well as the spectral losses, and the dispersion effects are parametrically investigated over wide range ranges of the set of affecting parameters {wavelength, ocean depth (and consequently the ocean pressure and temperature, and the chemical structure}.

  8. Modern Fiber Optic Submarine Cable Telecommunication Systems Planning for Explosive Bandwidth Needs at Different Deployment Depths

    Directory of Open Access Journals (Sweden)

    Ahmed Nabih Zaki Rashed

    2012-05-01

    Full Text Available The explosive bandwidth needs, especially in the inter data center market, have pushed transmission data rates to 100 Gbit/sec and beyond. Current terrestrial fibers are inadequate for long haul, high bandwidth deployments. To solve these problems a new fiber is introduced for terrestrial high bandwidth deployments: different polymeric core fibers with enlarged effective area with a significant optical signal to noise ratio improvement over other conventional terrestrial single mode fibers. To ensure the new fiber may be deployed robustly a new coating structure was employed. A rigorous cable structure was then chosen for evaluation. Based on experimental data, both the deep ocean water temperature and pressure are tailored as functions of the water depth. As well as the product of the transmitted bit rate and the repeater spacing is processed over wide ranges of the affecting parameters. It is taken into account the estimation of the total cost of the submarine fiber cable system for transmission technique under considerations. The system capacity as well as the spectral losses, and the dispersion effects are parametrically investigated over wide range ranges of the set of affecting parameters {wavelength, ocean depth (and consequently the ocean pressure and temperature, and the chemical structure}.

  9. High-Performance Harmonic Isolation and Load Voltage Regulation of the Three-Phase Series Active Filter Utilizing the Waveform Reconstruction Method

    DEFF Research Database (Denmark)

    Senturk, Osman Selcuk; Hava, Ahmet M.

    2009-01-01

    . The SAF-compensated system utilizing WRM provides highperformance load harmonic voltage isolation and load voltage regulation at steady-state and during transients compared to the system utilizing the synchronous reference-frame-based signal decomposition. In addition, reducing the line current sampling......This paper develops a waveform reconstruction method (WRM) for high accuracy and bandwidth signal decomposition of voltage-harmonic-type three-phase diode rectifier load voltage into its harmonic and fundamental components, which are utilized in the series active filter (SAF) control algorithms...

  10. Design of wide bandwidth pyramidal microwave absorbers using ferrite composites with broad magnetic loss spectra

    Science.gov (United States)

    Park, Myung-Jun; Kim, Sung-Soo

    2016-09-01

    Wide bandwidth microwave absorbers with a pyramidal shape and a significantly reduced thickness can be designed using high lossy ferrite materials with broad magnetic loss spectra. The microwave absorbing properties of pyramidal cone absorbers are analyzed using the transmission line approximation, which provides the reflection loss as a function of the material parameters and absorber geometry. Three types of ferrite materials (NiZn spinel ferrite, Co2Z hexaferrite, and RuCoM hexaferrite) are used as the absorbent fillers in a rubber matrix. Among these, Co2Z ferrite is the most suitable material for wide bandwidth pyramidal absorbers, due to its broad magnetic loss spectrum in the GHz frequency range. The optimal geometry of the pyramidal absorber is also determined using the transmission line theory. With the reduced total height of the pyramidal absorber (approximately 60 mm), a wide bandwidth (1.5-18 GHz with respect to the -20 dB reflection loss) can be realized. The proposed absorbers have a thickness advantage over the classical pyramidal ohmic absorbers; thus, they are suitable for small and semi-anechoic chambers.

  11. New methods for more effective use of bandwidth in MPLS networks with fast rerouting

    Science.gov (United States)

    Matsuoka, Yasuyuki; Kurimoto, Takashi; Nishikido, Jun; Urushidani, Shigeo

    2002-09-01

    Multi-protocol label switching (MPLS) technology is useful for IP Virtual Private Networks (IP-VPNs), guaranteeing bandwidth in IP (Internet Protocol) networks, and carrying out traffic engineering with explicit routing. The advantage of MPLS is its high capability to achieve of reliable networks when used with Fast Rerouting. However, Fast Rerouting requires a lot of network resources. This is because, for the rapid recovery of end-to-end communications after detection of failures, secondary LSPs must already have been reserved as detours in case there are failures on primary node-to-node links. The sharing of bandwidth among secondary LSPs is thus significant as a way of reducing the usage of network resources when Fast Rerouting is applied. In this paper, we propose a new routing algorithm in which bandwidth is shared among the secondary LSPs for multiple primary LSPs. This algorithm produces efficient network-level LSP designs. Three approaches to the dynamical changing of Open Shortest Path First (OSPF) link-cost metrics are applied in the algorithm. Each approach improves efficiency in the sharing of LSPs. The approaches are (1) the broader distribution of primary LSPs to reduce the need for detours in cases of single failures, (2) the concentration of secondary LSPs on links to increase the possibilities for bandwidth sharing, and (3) the distribution of secondary LSPs that cater to a certain failure, thus increasing the numbers of detouring LSPs which are independent of each other on the respective links. The scheme provides a slight improvement over the results of the conventional Dijkstra-algorithm calculation which is used in conventional OSPF. The proposed algorithms are applied with various network models that have been proposed in IETF Internet drafts, e.g.,

  12. [Estimation of rice LAI by using NDVI at different spectral bandwidths].

    Science.gov (United States)

    Wang, Fu-min; Huang, Jing-feng; Tang, Yan-lin; Wang, Xiu-zhen

    2007-11-01

    The canopy hyperspectral reflectance data of rice at its different development stages were collected from field measurement, and the corresponding NDVIs as well as the correlation coefficients of NDVIs and LAI were computed at extending bandwidth of TM red and near-infrared (NIR) spectra. According to the variation characteristics of best fitted R2 with spectral bandwidth, the optimal bandwidth was determined. The results showed that the correlation coefficients of LAI and ND-VI and the maximum R2 of the best fitted functions at different spectral bandwidths had the same variation trend, i.e., decreased with increasing bandwidth when the bandwidth was less than 60 nm. However, when the bandwidth was beyond 60 nm, the maximum R2 somewhat fluctuated due to the effect of NIR. The analysis of R2 variation with bandwidth indicated that 15 nm was the optimal bandwidth for the estimation of rice LAI by using NDVI.

  13. A system-level bandwidth design method for wormhole network-on-chip

    Science.gov (United States)

    Wang, Jian; Li, Yubai; Liao, Changjun

    2016-11-01

    To improve the Network-on-Chip (NoC) performance, we propose a system-level bandwidth design method customising the bandwidths of the NoC links. In details, we first built a mathematical model to catch the relationship between the NoC commutation latency and the NoC link bandwidth, and then develop a bandwidth allocation algorithm to automatically optimise the bandwidth for each NoC link. The experimental results show that our bandwidth-customising method improves the NoC performance compared to the traditional uniform bandwidth allocation method. Besides, it can also make our NoC to achieve the same communication performance level as the uniform bandwidth NoC but using fewer bandwidth resources, which is beneficial to save the NoC area and power.

  14. High-Throughput Analysis of Enzyme Activities

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Guoxin [Iowa State Univ., Ames, IA (United States)

    2007-01-01

    High-throughput screening (HTS) techniques have been applied to many research fields nowadays. Robot microarray printing technique and automation microtiter handling technique allows HTS performing in both heterogeneous and homogeneous formats, with minimal sample required for each assay element. In this dissertation, new HTS techniques for enzyme activity analysis were developed. First, patterns of immobilized enzyme on nylon screen were detected by multiplexed capillary system. The imaging resolution is limited by the outer diameter of the capillaries. In order to get finer images, capillaries with smaller outer diameters can be used to form the imaging probe. Application of capillary electrophoresis allows separation of the product from the substrate in the reaction mixture, so that the product doesn't have to have different optical properties with the substrate. UV absorption detection allows almost universal detection for organic molecules. Thus, no modifications of either the substrate or the product molecules are necessary. This technique has the potential to be used in screening of local distribution variations of specific bio-molecules in a tissue or in screening of multiple immobilized catalysts. Another high-throughput screening technique is developed by directly monitoring the light intensity of the immobilized-catalyst surface using a scientific charge-coupled device (CCD). Briefly, the surface of enzyme microarray is focused onto a scientific CCD using an objective lens. By carefully choosing the detection wavelength, generation of product on an enzyme spot can be seen by the CCD. Analyzing the light intensity change over time on an enzyme spot can give information of reaction rate. The same microarray can be used for many times. Thus, high-throughput kinetic studies of hundreds of catalytic reactions are made possible. At last, we studied the fluorescence emission spectra of ADP and obtained the detection limits for ADP under three different

  15. Metabolic Activity of Bacteria at High Pressure

    Science.gov (United States)

    Picard, A.; Daniel, I.; Oger, P.

    2008-12-01

    Over the last 20 years, there has been increasing evidence for the presence of a large number of microbes in the oceanic subsurface. Such a habitat has a very low energy input because it is deprived of light. A few meters below the sediment surface, conditions are already anoxic in most cases, sulfate reduction and/or methanogenesis becoming thus the primary respiratory reactions of organic matter. Neither the fate of methanogenesis, nor the fate of Dissimilatory Metal-Reduction (DMR) has been investigated so far as a function of pressure. For this reason, we measured experimentally the pressure limits of microbial anaerobic energetic metabolism. In practice, we measured in situ the kinetics of selenite respiration by the bacterial model Shewanella oneidensis MR-1 under high hydrostatic pressure (HHP) between 0 and 150 MPa at 30°C. MR-1 stationary-phase cells were used in Luria-Bertani (LB) medium amended with lactate as an additional electron donor and sodium selenite as an electron acceptor. In situ measurements were performed by X- ray Absorption Near-Edge Structure (XANES) spectroscopy in both a diamond-anvil cell and an autoclave. A red precipitate of amorphous Se(0) was virtually observed at any pressure to 150 MPa. A progressive reduction of selenite Se(IV) into selenium Se(0) was also observed in the evolution of XANES spectra with time. All kinetics between 0.1 and 150 MPa can be adjusted to a first order kinetic law. MR-1 respires all available selenite up to 60 MPa. Above 60 MPa, the respiration yield decreases linearly as a function of pressure and reaches 0 at 155 ±5 MPa. This indicates that selenite respiration by Shewanella oneidensis MR-1 stops at about 155 MPa, whereas its growth is arrested at 50 MPa. Hence, the present results show that the respiration of selenium by the strain MR-1 occurs efficiently up to 60 MPa and 30°C, i.e. from the surface of a continental sediment to an equivalent depth of about 2 km, or beneath a 5-km water column and

  16. Phase noise measurement of high-power fiber amplifiers

    Institute of Scientific and Technical Information of China (English)

    Hu Xiao; Xiaolin Wang; Yanxing Ma; Bing He; Pu Zhou; Jun Zhou; Xiaojun Xu

    2011-01-01

    We measure the phase fluctuation in a high-power fiber amplifier using a multi-dithering technique. Its fluctuation property is qualitatively analyzed by the power spectral density and integrated spectral density.Low frequency fluctuations caused by the environment are dominant in the phase fluctuations in an amplifier, whereas the high frequency components related to laser power affect the control bandwidth. The bandwidth requirement of the active phase-locking is calculated to be 300 Hz, 670 Hz, 1.6 kHz, and 3.9 kHz under the output power of 25,55, 125, and 180W, respectively. The approximately linear relationship between the control bandwidth and laser power needs to be further investigated.%@@ We measure the phase fluctuation in a high-power fiber amplifier using a multi-dithering technique.Its fluctuation property is qualitatively analyzed by the power spectral density and integrated spectral density.Low frequency fluctuations caused by the environment are dominant in the phase fluctuations in an am-plifier, whereas the high frequency components related to laser power affect the control bandwidth.The bandwidth requirement of the active phase-locking is calculated to be 300 Hz, 670 Hz, 1.6 kHz, and 3.9kHz under the output power of 25, 55, 125, and 180 W, respectively.The approximately linear relationship between the control bandwidth and laser power needs to be further investigated.

  17. The Bandwidths of a Matrix. A Survey of Algorithms

    Directory of Open Access Journals (Sweden)

    Mafteiu-Scai Liviu Octavian

    2014-12-01

    Full Text Available The bandwidth, average bandwidth, envelope, profile and antibandwidth of the matrices have been the subjects of study for at least 45 years. These problems have generated considerable interest over the years because of them practical relevance in areas like: solving the system of equations, finite element methods, circuit design, hypertext layout, chemical kinetics, numerical geophysics etc. In this paper a brief description of these problems are made in terms of their definitions, followed by a comparative study of them, using both approaches: matrix geometry and graph theory. Time evolution of the corresponding algorithms as well as a short description of them are made. The work also contains concrete real applications for which a large part of presented algorithms were developed.

  18. Conical Emission Patterns by Femtosecond Pulses with Different Spectral Bandwidths

    Institute of Scientific and Technical Information of China (English)

    LI Yue-Xun; ZENG Zhi-Nan; GE Xiao-Chun; CHEN Xiao-Wei; LI Ru-Xin; XU Zhi-Zhan

    2008-01-01

    @@ Different conical emission (CE) patterns are obtained experimentally at various incident powers and beam sizes of pump laser pulses with pulse durations of 7fs, 44fs and lOOfs.The results show that it is the incident power but not the incident power density that determines a certain CE pattern.In addition, the critical powers for similar CE patterns are nearly the same for the laser pulses with the same spectral bandwidth.Furthermore, as far as a certain CE pattern is concerned, the wider the spectral bandwidth of pump laser pulse is, the higher the critical power is.This will hopefully provide new insights for the generation of CE pattern in optical medium.

  19. Variable bandwidth and one-step local M-estimator

    Institute of Scientific and Technical Information of China (English)

    范剑青; 蒋建成

    2000-01-01

    A robust version of local linear regression smoothers augmented with variable bandwidth is studied. The proposed method inherits the advantages of local polynomial regression and overcomes the shortcoming of lack of robustness of least-squares techniques. The use of variable bandwidth enhances the flexibility of the resulting local M- estimators and makes them possible to cope well with spatially inho-mogeneous curves, heteroscedastic errors and nonuniform design densities. Under appropriate regularity conditions, it is shown that the proposed estimators exist and are asymptotically normal. Based on the robust estimation equation, one-step local M-estimators are introduced to reduce computational burden. It is demonstrated that the one-step local M-estimators share the same asymptotic distributions as the fully iterative M-estimators, as long as the initial estimators are good enough. In other words, the one-step local M-estimators reduce significantly the computation cost of the fully iterative M-estim

  20. GHz bandwidth noise eater hybrid optical amplifier: design guidelines.

    Science.gov (United States)

    Danion, Gwennaël; Bondu, François; Loas, Goulc'hen; Alouini, Mehdi

    2014-07-15

    This Letter describes the design of an optical amplifier system optimized to reduce the relative intensity noise (RIN) of the input signal, and discloses its performance in terms of intensity noise reduction and bandwidth, without phase noise degradation. This polarization-maintaining amplifier is composed of an erbium-doped fiber amplifier (EDFA) cascaded with a semiconductor optical amplifier (SOA). The EDFA is sized to feed the SOA with a constant power corresponding to the optimal saturation level for noise reduction, through coherent population oscillations. When properly optimized, such an amplifier provides, simultaneously, 17 dB optical gain, 5.4 dB noise factor, and 20 dB reduction of the input-RIN across a 3 GHz bandwidth, without any electronics feedback loop.

  1. Bandwidth-enhanced photopolymer waveguide hologram-based optical backplane

    Science.gov (United States)

    Bi, Hai; Tian, Chuhua; Chen, Ray T.; Han, Xuliang

    2005-01-01

    As multiprocessing comes into the mainstream, the board-to-board interconnects become even more critical. In a shared-memory multiprocessing system, the shared bus topology is the preferred interconnect scheme because its broadcast nature can be effectively utilized to reduce communication latency, lessen networking complexity, and support cache coherence. In the electrical domain, however, a major performance bottleneck is anticipated due to the restricted bus bandwidth. In this paper, an innovative architecture, optical centralized shared bus, is proposed for use in the multiprocessing systems. This architecture utilizes the terascale bandwidth capacity of substrate-guided optical interconnects, while at the same time, retaining the essential merits of the shared bus topology. Thus, a smooth migration with substantial multiprocessing performance improvement is expected. A conceptual emulation of the shared-memory multiprocessing scheme is demonstrated on a generic PCI subsystem with an optical centralized shared bus. The objective of this effort is to prove the technical feasibility from the architecture standpoint.

  2. Transportation dynamic on coupled networks with limited bandwidth

    CERN Document Server

    Li, Ming; Wang, Bing-Hong

    2016-01-01

    The communication networks in real world often couple with each other to save costs, which results in any network does not have a stand-alone function and efficiency. To investigate this, in this paper we propose a transportation model on two coupled networks with bandwidth sharing. We find that the free-flow state and the congestion state can coexist in the two coupled networks, and the free-flow path and congestion path can coexist in each network. Considering three bandwidth-sharing mechanisms, random, assortative and disassortative couplings, we also find that the transportation capacity of the network only depends on the coupling mechanism, and the fraction of coupled links only affects the performance of the system in the congestion state, such as the traveling time. In addition, with assortative coupling, the traffic capacity of the system will decrease significantly. However, the disassortative coupling has little influence on the transportation capacity of the system, which provides a good strategy t...

  3. Ultrawide Bandwidth 180°-Hybrid-Coupler in Planar Technology

    Directory of Open Access Journals (Sweden)

    Steffen Scherr

    2014-01-01

    Full Text Available A new concept of an ultrawide bandwidth 180°-hybrid-coupler is presented. The ultrawideband design approach is based on the excitation of a coplanar waveguide (CPW mode and a coupled slot line (CSL mode in the same double slotted planar waveguide. The coupler is suitable for realization in planar printed circuit board technology. For verification of the new concept a prototype was designed for the frequency range from 3 GHz to 11 GHz, built, and measured. The measurement results presented in this paper show a good agreement between simulation and measurement and demonstrate the very broadband performance of the new device. The demonstrated coupler with a size of 40 mm × 55 mm exhibits a fractional bandwidth of 114% centered at 7 GHz with a maximum amplitude imbalance of 0.8 dB and a maximum phase imbalance of 5°.

  4. A Constant Percentage Bandwidth Transform for Acoustic Signal Processing

    Science.gov (United States)

    1980-01-01

    defined a:- ’ho riti of the center frequency of a response peak to the -1 decibel bandwidth of that peak.) Though it has been extended in accuracy...F (w) on frequency. The solution of this problem necessitates the formalization of some simple ideas. First, define F (w) to be the -3 decibel ...the speech waveform, particularly during vowels and pauses. Interested primarily in taking advantage of this redundancy to facilitate time multiplexing

  5. Quantum gates with optimal bandwidth in noisy environments

    Science.gov (United States)

    Low, Guang Hao; Theodore, Yoder; Chuang, Isaac

    The traditional approach of open-loop quantum error correction suppresses certain systematic imperfections ɛ in quantum control to higher orders ɛ  (L) by a well-designed sequence of L imperfect quantum gates. However, this philosophy of maximal flatness leads to an ɛ-bandwidth that scales poorly with length and a residual that is easily overwhelmed by unaccounted sources of noise. We advance the paradigm of equiripple compensated gates that directly optimize for bandwidth given the limitations imposed by noise of magnitude δ, leading to dramatically improved performance. Where ɛ represent amplitude errors, we provide a formalism that generalizes both approaches and is effective at finding such gates. With it, we provide in closed-form the phase angles for an optimal family of population inversion gates with an ɛ -bandwidth of  (logδ-1/L) - a quadratic improvement over optimal maximally flat variants. We also construct optimal NOT gates and discuss extensions to other gates and error models.

  6. DC SQUID RF magnetometer with 200 MHz bandwidth

    Science.gov (United States)

    Talanov, Vladimir; Lettsome, Nesco; Orozco, Antonio; Cawthorne, Alfred; Borzenets, Valery

    2012-02-01

    Because of periodic flux-to-voltage transfer function, Superconducting QUantum Interference Device (SQUID) magnetometers operate in a closed-loop regime [1], which linearizes the response, and increases the dynamic range and sensitivity. However, a transmission line delay between the SQUID and electronics fundamentally limits the closed-loop bandwidth at 20 MHz [1], although the intrinsic bandwidth of SQUIDs is in gigahertz range. We designed a DC SQUID based RF magnetometer capable of wideband sensing coherent magnetic fields up to 200 MHz. To overcome the closed-loop bandwidth limitation, we utilized a low-frequency flux-modulated closed-loop to simultaneously lock the quasi-static magnetic flux and provide AC bias for the RF flux. The SQUID RF voltage is processed by RF electronics based on a double lock-in technique. This yields a signal proportional to the amplitude and phase of the RF magnetic flux, with more than four decades of a linear response. For YBaCuO SQUID on bi-crystal SrTiO substrate at 77 K we achieved a flux noise density of 4 μφ0/Hz at 190 MHz, which is similar to that measured at kHz frequencies with conventional flux-locked loop. [1] D. Drung, et al., Supercond. Sci. Technol. 19, S235 (2006).

  7. Bandwidth Enhancement Technique of the Meandered Monopole Antenna

    Directory of Open Access Journals (Sweden)

    Chien-Jen Wang

    2015-01-01

    Full Text Available A small dual-band monopole antenna with coplanar waveguide (CPW feeding structure is presented in this paper. The antenna is composed of a meandered monopole, an extended conductor tail, and an asymmetrical ground plane. Tuning geometrical structure of the ground plane excites an additional resonant frequency band and thus enhances the impedance bandwidth of the meandered monopole antenna. Unlike the conventional monopole antenna, the new resonant mode is excited by a slot trace of the CPW transmission line. The radiation performance of the slot mode is as similar as that of the monopole. The parametrical effect of the size of the one-side ground plane on impedance matching condition has been derived by the simulation. The measured impedance bandwidths, which are defined by the reflection coefficient of −6 dB, are 186 MHz (863–1049 MHz, 19.4% at the lower resonant band and 1320 MHz (1490–2810 MHz, 61.3% at the upper band. From the results of the reflection coefficients of the proposed monopole antenna, the operated bandwidths of the commercial wireless communication systems, such as GSM 900, DCS, IMT-2000, UMTS, WLAN, LTE 2300, and LTE 2500, are covered for uses.

  8. Allocating Bandwidth in Datacenter Networks:A Survey

    Institute of Scientific and Technical Information of China (English)

    陈丽; 李葆春; 李波

    2014-01-01

    Datacenters have played an increasingly essential role as the underlying infrastructure in cloud computing. As implied by the essence of cloud computing, resources in these datacenters are shared by multiple competing entities, which can be either tenants that rent virtual machines (VMs) in a public cloud such as Amazon EC2, or applications that embrace data parallel frameworks like MapReduce in a private cloud maintained by Google. It has been generally observed that with traditional transport-layer protocols allocating link bandwidth in datacenters, network traffic from competing applications interferes with each other, resulting in a severe lack of predictability and fairness of application performance. Such a critical issue has drawn a substantial amount of recent research attention on bandwidth allocation in datacenter networks, with a number of new mechanisms proposed to efficiently and fairly share a datacenter network among competing entities. In this article, we present an extensive survey of existing bandwidth allocation mechanisms in the literature, covering the scenarios of both public and private clouds. We thoroughly investigate their underlying design principles, evaluate the trade-off involved in their design choices and summarize them in a unified design space, with the hope of conveying some meaningful insights for better designs in the future.

  9. Comparing adaptive and fixed bandwidth-based kernel density estimates in spatial cancer epidemiology.

    Science.gov (United States)

    Lemke, Dorothea; Mattauch, Volkmar; Heidinger, Oliver; Pebesma, Edzer; Hense, Hans-Werner

    2015-03-31

    Monitoring spatial disease risk (e.g. identifying risk areas) is of great relevance in public health research, especially in cancer epidemiology. A common strategy uses case-control studies and estimates a spatial relative risk function (sRRF) via kernel density estimation (KDE). This study was set up to evaluate the sRRF estimation methods, comparing fixed with adaptive bandwidth-based KDE, and how they were able to detect 'risk areas' with case data from a population-based cancer registry. The sRRF were estimated within a defined area, using locational information on incident cancer cases and on a spatial sample of controls, drawn from a high-resolution population grid recognized as underestimating the resident population in urban centers. The spatial extensions of these areas with underestimated resident population were quantified with population reference data and used in this study as 'true risk areas'. Sensitivity and specificity analyses were conducted by spatial overlay of the 'true risk areas' and the significant (α=.05) p-contour lines obtained from the sRRF. We observed that the fixed bandwidth-based sRRF was distinguished by a conservative behavior in identifying these urban 'risk areas', that is, a reduced sensitivity but increased specificity due to oversmoothing as compared to the adaptive risk estimator. In contrast, the latter appeared more competitive through variance stabilization, resulting in a higher sensitivity, while the specificity was equal as compared to the fixed risk estimator. Halving the originally determined bandwidths led to a simultaneous improvement of sensitivity and specificity of the adaptive sRRF, while the specificity was reduced for the fixed estimator. The fixed risk estimator contrasts with an oversmoothing tendency in urban areas, while overestimating the risk in rural areas. The use of an adaptive bandwidth regime attenuated this pattern, but led in general to a higher false positive rate, because, in our study design

  10. Optimization Design Parameters of Electro-optic Modulators for Low Loss Wide Bandwidth Capability of Optical Communication Systems

    Directory of Open Access Journals (Sweden)

    Ahmed Nabih Zaki Rashed

    2012-06-01

    Full Text Available The effects of temperature, and operating signal wavelength on high frequency radio frequency transmission characteristics are deeply investigated against various materials based electro optic modulator devices such as lithium Niobate (LiNbO3, polymer, and semiconductor materials. On the other hand, we have developed the optimization of the electro optic modulator parameters where the effective index plays an essential role in the evaluation of the bandwidth structure. The effects of design parameters on the modulating voltage and optical bandwidth are also investigated for different materials based electro optic modulators by using rigorous transmission modeling techniques. The low loss wide bandwidth capability of optoelectronic systems makes them attractive for the transmission and processing of microwave signals, while the development of high capacity optical communication systems has required the use of modulation techniques in optical transmitters and receivers. This paper has presented the low loss wide bandwidth for different electrooptic modulators based on design of optimization parameters for high speed transmission performance.

  11. Bandwidth-Efficient Mutually Cooperative Relaying with Spatially Coordinate-Interleaved Orthogonal Design

    Science.gov (United States)

    Ryu, Hyun-Seok; Park, Kyung-Mi; Lee, Hee-Soo; Kang, Chung-Gu

    This letter proposes a type of mutually cooperative relaying (MCR) scheme based on a spatially coordinate-interleaved orthogonal design (SCID), in which two cooperative users are spatially multiplexed without bandwidth expansion. It provides not only diversity gain (with order of two) as in the existing MCR scheme, but also additional coding gain. Our simulation results demonstrate that the proposed SCID scheme is useful for improving the uplink performance as long as one user can find another active user as a close neighbor that is simultaneously communicating with the same destination, e.g., a base station in the cellular network.

  12. Production of medical radioisotopes with high specific activity in photonuclear reactions with γ-beams of high intensity and large brilliance

    Science.gov (United States)

    Habs, D.; Köster, U.

    2011-05-01

    We study the production of radioisotopes for nuclear medicine in ( γ, xn+ yp) photonuclear reactions or ( γ, γ') photoexcitation reactions with high-flux [(1013-1015) γ/s], small diameter ˜(100 μm)2 and small bandwidth (Δ E/ E≈10-3-10-4) γ beams produced by Compton back-scattering of laser light from relativistic brilliant electron beams. We compare them to (ion, xn+ yp) reactions with (ion = p,d, α) from particle accelerators like cyclotrons and (n, γ) or (n,f) reactions from nuclear reactors. For photonuclear reactions with a narrow γ-beam the energy deposition in the target can be managed by using a stack of thin target foils or wires, hence avoiding direct stopping of the Compton and pair electrons (positrons). However, for ions with a strong atomic stopping only a fraction of less than 10-2 leads to nuclear reactions resulting in a target heating, which is at least 105 times larger per produced radioactive ion and often limits the achievable activity. In photonuclear reactions the well defined initial excitation energy of the compound nucleus leads to a small number of reaction channels and enables new combinations of target isotope and final radioisotope. The narrow bandwidth γ excitation may make use of the fine structure of the Pygmy Dipole Resonance (PDR) or fluctuations in γ-width leading to increased cross sections. Within a rather short period compared to the isotopic half-life, a target area of the order of (100 μm)2 can be highly transmuted, resulting in a very high specific activity. ( γ, γ') isomer production via specially selected γ cascades allows to produce high specific activity in multiple excitations, where no back-pumping of the isomer to the ground state occurs. We discuss in detail many specific radioisotopes for diagnostics and therapy applications. Photonuclear reactions with γ-beams allow to produce certain radioisotopes, e.g. 47Sc, 44Ti, 67Cu, 103Pd, 117 m Sn, 169Er, 195 m Pt or 225Ac, with higher specific activity

  13. Two Bandwidth Packing Algorithms for the Centralized Wireless Network and Their Average-case Analysis

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    This paper presents a detail analysis of two bandwidth packing algorithms, used for processing connection requests in the centralized wireless network. Each call comes with a specific bandwidth request. A request can be satisfied only if there is sufficient bandwidth available during resource scheduling and allocation. Unsatisfied requests were held in a queue. The metric of bandwidth utilization ratio was used to quantify the performance of our algorithms. By theoretical analysis, our algorithms can improve the average bandwidth usage ratio significantly,about 8%~ 10% without adding much computation complexity. Moreover, our algorithms outperform next fit with fragmentation (NFF) algorithm when the bandwidth resource is scarce. In this paper, the contributions follows: Introducing bandwidth packing problem into wireless network; Proposing two new bandwidth packing algorithms for wireless network where the complicate scheduling algorithms are prohibited; Studying the average performance of our algorithms mathematically, which agree well with the simulation results.

  14. Bandwidth-variable tunable optical filter unit for illumination and spectral imaging systems using thin-film optical band-pass filters.

    Science.gov (United States)

    Hennig, Georg; Brittenham, Gary M; Sroka, Ronald; Kniebühler, Gesa; Vogeser, Michael; Stepp, Herbert

    2013-04-01

    An optical filter unit is demonstrated, which uses two successively arranged tunable thin-film optical band-pass filters and allows for simultaneous adjustment of the central wavelength in the spectral range 522-555 nm and of the spectral bandwidth in the range 3-16 nm with a wavelength switching time of 8 ms∕nm. Different spectral filter combinations can cover the complete visible spectral range. The transmitted intensity was found to decrease only linearly with the spectral bandwidth for bandwidths >6 nm, allowing a high maximum transmission efficiency of >75%. The image of a fiber bundle was spectrally filtered and analyzed in terms of position-dependency of the transmitted bandwidth and central wavelength.

  15. Subpicosecond electron-hole recombination time and terahertz-bandwidth photoresponse in freestanding GaAs epitaxial mesoscopic structures

    Science.gov (United States)

    Mikulics, Martin; Zhang, Jie; Serafini, John; Adam, Roman; Grützmacher, Detlev; Sobolewski, Roman

    2012-07-01

    We present the ultrafast (THz-bandwidth) photoresponse from GaAs single-crystal mesoscopic structures, such as freestanding whiskers and platelets fabricated by the top-down technique, transferred onto a substrate of choice, and incorporated into a coplanar strip line. We recorded electrical transients as short as ˜600 fs from an individual whisker photodetector. Analysis of the frequency spectrum of the photoresponse electrical signal showed that, intrinsically, our device was characterized by an ˜150-fs carrier lifetime and an overall 320-fs response. The corresponding 3-dB frequency bandwidth was 1.3 THz—the highest bandwidth ever reported for a GaAs-based photodetector. Simultaneously, as high-quality, epitaxially grown crystals, our GaAs structures exhibited mobility values as high as ˜7300 cm2/V.s, extremely low dark currents, and ˜7% intrinsic detection efficiency, which, together with their experimentally measured photoresponse repetition time of ˜1 ps, makes them uniquely suitable for terahertz-frequency optoelectronic applications, ranging from ultrafast photon detectors and counters to THz-bandwidth optical-to-electrical transducers and photomixers.

  16. Highly active thermally stable nanoporous gold catalyst

    Science.gov (United States)

    Biener, Juergen; Wittstock, Arne; Biener, Monika M.; Bagge-Hansen, Michael; Baeumer, Marcus; Wichmann, Andre; Neuman, Bjoern

    2016-12-20

    In one embodiment, a system includes a nanoporous gold structure and a plurality of oxide particles deposited on the nanoporous gold structure; the oxide particles are characterized by a crystalline phase. In another embodiment, a method includes depositing oxide nanoparticles on a nanoporous gold support to form an active structure and functionalizing the deposited oxide nanoparticles.

  17. Highly active thermally stable nanoporous gold catalyst

    Energy Technology Data Exchange (ETDEWEB)

    Biener, Juergen; Wittstock, Arne; Biener, Monika M.; Bagge-Hansen, Michael; Baeumer, Marcus; Wichmann, Andre; Neuman, Bjoern

    2016-12-20

    In one embodiment, a system includes a nanoporous gold structure and a plurality of oxide particles deposited on the nanoporous gold structure; the oxide particles are characterized by a crystalline phase. In another embodiment, a method includes depositing oxide nanoparticles on a nanoporous gold support to form an active structure and functionalizing the deposited oxide nanoparticles.

  18. Optimization of Gain, Impedance, and Bandwidth of Yagi-Uda Array Using Particle Swarm Optimization

    Directory of Open Access Journals (Sweden)

    Munish Rattan

    2008-01-01

    Full Text Available Particle swarm optimization (PSO is a new, high-performance evolutionary technique, which has recently been used for optimization problems in antennas and electromagnetics. It is a global optimization technique-like genetic algorithm (GA but has less computational cost compared to GA. In this paper, PSO has been used to optimize the gain, impedance, and bandwidth of Yagi-Uda array. To evaluate the performance of designs, a method of moments code NEC2 has been used. The results are comparable to those obtained using GA.

  19. Electric field and temperature measurement using ultra wide bandwidth pigtailed electro-optic probes.

    Science.gov (United States)

    Bernier, Maxime; Gaborit, Gwenaël; Duvillaret, Lionel; Paupert, Alain; Lasserre, Jean-Louis

    2008-05-01

    We present pigtailed electro-optic probes that allow a simultaneous measurement of high frequency electric fields and temperature using a unique laser probe beam. This has been achieved by the development of a novel probe design associated with a fully automated servo-controlled optical bench, initially developed to stabilize the electric field sensor response. The developed electro-optic probes present a stable response in outdoors conditions over a time duration exceeding 1 h, a frequency bandwidth from kHz to tens of GHz with a sensitivity of 0.7 Vm(-1)Hz(-(1/2)), and a temperature accuracy of 40 mK.

  20. Efficient, designable, and broad-bandwidth optical extinction via aspect-ratio-tailored silver nanodisks

    CERN Document Server

    Anquillare, E L; Hsu, C W; DeLacy, B G; Joannopoulos, J D; Johnson, S G; Soljacic, M

    2016-01-01

    Subwavelength resonators, ranging from single atoms to metallic nanoparticles, typically exhibit a narrow-bandwidth response to optical excitations. We computationally design and experimentally synthesize tailored distributions of silver nanodisks to extinguish light over broad and varied frequency windows. We show that metallic nanodisks are two-to-ten-times more efficient in absorbing and scattering light than common structures, and can approach fundamental limits to broadband scattering for subwavelength particles. We measure broadband extinction per volume that closely approaches theoretical predictions over three representative visible-range wavelength windows, confirming the high efficiency of nanodisks and demonstrating the collective power of computational design and experimental precision for developing new photonics technologies.

  1. A 10 MHz Bandwidth Continuous-Time Delta-Sigma Modulator for Portable Ultrasound Scanners

    DEFF Research Database (Denmark)

    Llimos Muntal, Pere; Jørgensen, Ivan Harald Holger; Bruun, Erik

    2016-01-01

    A fourth-order 1-bit continuous-time delta-sigma modulator designed in a 65 nm process for portable ultrasound scanners is presented in this paper. The loop filter consists of RCintegrators, with programmable capacitor arrays and resistors, and the quantizer is implemented with a high-speed clocked...... comparator and a pull-down clocked latch. The feedback signal is generated with voltage DACs based on transmission gates. Using this implementation, a small and low-power solution required for portable ultrasound scanner applications is achieved. The modulator has a bandwidth of 10 MHz with an oversampling...

  2. GHz-bandwidth upconversion detector using a unidirectional ring cavity to reduce multilongitudinal mode pump effects

    DEFF Research Database (Denmark)

    Meng, Lichun; Høgstedt, Lasse; Tidemand-Lichtenberg, Peter

    2017-01-01

    narrow-linewidth lasers in a fiber coupler while tuning their wavelength difference down to 10 pm or less. The SFG crystal is placed inside an Nd:YVO4 ring cavity that provides 1064 nm circulating pump powers of up to 150 W in unidirectional operation. Measured Fabry-Perot spectrum at 1064 nm confirms...... for cooling, the GHz-bandwidth upconverter can readily be extended to the mid-IR (2 - 5 mu m) as an alternative to cooled low-bandgap semiconductor detectors for applications such as high-speed free-space optical communications. (C) 2017 Optical Society of America...

  3. Optimization of bandwidth of communication channels of corporate networks

    Directory of Open Access Journals (Sweden)

    G. I. Bondarenko

    2014-09-01

    Full Text Available Introduction. This article contains overview of the organization of communication between applications on the corporate network. It is stated that the main digital channel (channel B - 64 kbit/s and the primary digital channel (channel E1 the digital stream - 2048 kbit/s are used as the main channels in corporate networks. Problem areas of the functioning of the corporate network are identified. There are the rent of communication channels, which is growing rapidly with increasing the quality and speed of data transmission, and optimal use of bandwidth of communication channels. Setting of task. Optimal use of transmission channels bandwidth and minimizing the rent cost of channels is possible in two ways - the use of compression techniques of voice and video information and the application of variable structure of channels by using various-speed transmission channels. Differential pulse code modulation, adaptive differential pulse code modulation are the modern methods of speech signals processing. Organization of various-speed channels is performed in the structure of the BCC (for speech signals or PCR (for video. Suggestions for optimizing the structure of the channel signals. Proposed method of various-speed channels formation by using the channel intervals appropriate BCC (octets in the structure of signals E1 as envelopes containing various-speed channels. Channels can be selected for synchronization procedure CRC to simplify recognition of channels in the structure of E1. In this case, the minimal speed in the channel is 4 kbit/s. Conclusions. The proposed structure of envelopes is based on octet channel intervals of standard group signal of the primary group plesiochronous hierarchy E1 when transferring various-speed digital signals maximum allows to use the bandwidth at a fixed structure of channel interval, it makes possible to agree on the structure of the various-speed signals with the existing in communication networks.

  4. Tunable polarization plasma channel undulator for narrow bandwidth photon emission

    Science.gov (United States)

    Rykovanov, S. G.; Wang, J. W.; Kharin, V. Yu.; Lei, B.; Schroeder, C. B.; Geddes, C. G. R.; Esarey, E.; Leemans, W. P.

    2016-09-01

    The theory of a plasma undulator excited by a short intense laser pulse in a parabolic plasma channel is presented. The undulator fields are generated either by the laser pulse incident off-axis and/or under the angle with respect to the channel axis. Linear plasma theory is used to derive the wakefield structure. It is shown that the electrons injected into the plasma wakefields experience betatron motion and undulator oscillations. Optimal electron beam injection conditions are derived for minimizing the amplitude of the betatron motion, producing narrow-bandwidth undulator radiation. Polarization control is readily achieved by varying the laser pulse injection conditions.

  5. Low Bandwidth Vocoding using EM Sensor and Acoustic Signal Processing

    Energy Technology Data Exchange (ETDEWEB)

    Ng, L C; Holzrichter, J F; Larson, P E

    2001-10-25

    Low-power EM radar-like sensors have made it possible to measure properties of the human speech production system in real-time, without acoustic interference [1]. By combining these data with the corresponding acoustic signal, we've demonstrated an almost 10-fold bandwidth reduction in speech compression, compared to a standard 2.4 kbps LPC10 protocol used in the STU-III (Secure Terminal Unit, third generation) telephone. This paper describes a potential EM sensor/acoustic based vocoder implementation.

  6. Frequency Bandwidth of Half-Wave Impedance Repeater

    Directory of Open Access Journals (Sweden)

    Marek Dvorsky

    2012-01-01

    Full Text Available This article brings in the second part general information about half-wave impedance repeater. The third part describes the basic functional principles of the half-wave impedance repeater using Smith chart. The main attention is focused in part four on the derivation of repeater frequency bandwidth depending on characteristics and load impedance of unknown feeder line. Derived dependences are based on the elementary features of the feeder lines with specific length. The described functionality is proved in part 4.3 by measurement of transformed impedance using vector several unbalanced feeder lines and network analyzer VNWA3+.

  7. Space bandwidth-efficient realizations of linear systems.

    Science.gov (United States)

    Kutay, M A; Erden, M F; Ozaktas, H M; Arkan, O; Güleryüz, O; Candan, C A

    1998-07-15

    One can obtain either exact realizations or useful approximations of linear systems or matrix-vector products that arise in many different applications by implementing them in the form of multistage or multichannel fractional Fourier-domain filters, resulting in space-bandwidth-efficient systems with acceptable decreases in accuracy. Varying the number and the configuration of filters enables one to trade off between accuracy and efficiency in a flexible manner. The proposed scheme constitutes a systematic way of exploiting the regularity or structure of a given linear system or matrix, even when that structure is not readily apparent.

  8. Bandwidth allocation for video under quality of service constraints

    CERN Document Server

    Anjum, Bushra

    2014-01-01

    We present queueing-based algorithms to calculate the bandwidth required for a video stream so that the three main Quality of Service constraints, i.e., end-to-end delay, jitter and packet loss, are ensured. Conversational and streaming video-based applications are becoming a major part of the everyday Internet usage. The quality of these applications (QoS), as experienced by the user, depends on three main metrics of the underlying network, namely, end-to-end delay, jitter and packet loss. These metrics are, in turn, directly related to the capacity of the links that the video traffic trave

  9. Implementasi Manajemen Bandwidth Dengan Disiplin Antrian Hierarchical Token Bucket (HTB Pada Sistem Operasi Linux

    Directory of Open Access Journals (Sweden)

    Muhammad Nugraha

    2016-09-01

    Full Text Available Important Problem on Internet networking is exhausted resource and bandwidth by some user while other user did not get service properly. To overcome that problem we need to implement traffic control and bandwidth management system in router. In this research author want to implement Hierarchical Token Bucket algorithm as queue discipline (qdisc to get bandwidth management accurately in order the user can get bandwidth properly. The result of this research is form the management bandwidth cheaply and efficiently by using Hierarchical Token Bucket qdisc on Linux operating system were able to manage the user as we want.

  10. Frequencies, bandwidths and magnitudes of vocal tract and surrounding tissue resonances, measured through the lips during phonation.

    Science.gov (United States)

    Hanna, Noel; Smith, John; Wolfe, Joe

    2016-05-01

    The frequencies, magnitudes, and bandwidths of vocal tract resonances are all important in understanding and synthesizing speech. High precision acoustic impedance spectra of the vocal tracts of 10 subjects were measured from 10 Hz to 4.2 kHz by injecting a broadband acoustic signal through the lips. Between 300 Hz and 4 kHz the acoustic resonances R (impedance minima measured through the lips) and anti-resonances R¯ (impedance maxima) associated with the first three voice formants, have bandwidths of ∼50 to 90 Hz for men and ∼70 to 90 Hz for women. These acoustic resonances approximate those of a smooth, dry, rigid cylinder of similar dimensions, except that their bandwidths indicate higher losses in the vocal tract. The lossy, inertive load and airflow caused by opening the glottis further increase the bandwidths observed during phonation. The vocal tract walls are not rigid and measurements show an acousto-mechanical resonance R0 ∼ 20 Hz and anti-resonance R¯0∼200 Hz. These give an estimate of wall inertance consistent with an effective thickness of 1-2 cm and a wall stiffness of 2-4 kN m(-1). The non-rigidity of the tract imposes a lower limit of the frequency of the first acoustic resonance fR1 and the first formant F1.

  11. Photonic-chip-based radio-frequency spectrum analyser with terahertz bandwidth

    Science.gov (United States)

    Pelusi, Mark; Luan, Feng; Vo, Trung D.; Lamont, Michael R. E.; Madden, Steven J.; Bulla, Douglas A.; Choi, Duk-Yong; Luther-Davies, Barry; Eggleton, Benjamin J.

    2009-03-01

    Signal processing at terahertz speeds calls for an enormous leap in bandwidth beyond the current capabilities of electronics, for which practical operation is currently limited to tens of gigahertz. This can be achieved through all-optical schemes making use of the ultrafast response of χ(3) nonlinear waveguides. Towards this objective, we have developed compact planar rib waveguides based on As2S3 glass, providing a virtual `lumped' high nonlinearity in a monolithic platform capable of integrating multiple functions. Here, we apply it to demonstrate, for the first time, a photonic-chip-based, all-optical, radio-frequency spectrum analyser with the performance advantages of distortion-free, broad measurement bandwidth (>2.5 THz) and flexible wavelength operation (that is, colourless). The key to this is the waveguide's high optical nonlinearity and dispersion-shifted design. Using the device, we characterize high-bit-rate (320 Gb s-1) optical signals impaired by various distortions. The demonstrated ultrafast, broadband capability highlights the potential for integrated chip-based signal processing at bit rates approaching and beyond Tb s-1.

  12. An Exponential Time 2-Approximation Algorithm for Bandwidth

    CERN Document Server

    Fürer, Martin; Kasiviswanathan, Shiva Prasad

    2009-01-01

    The bandwidth of a graph G on n vertices is the minimum b such that the vertices of G can be labeled from 1 to n such that the labels of every pair of adjacent vertices differ by at most b. In this paper, we present a 2-approximation algorithm for the bandwidth problem that takes worst-case O(1.9797^n) time and uses polynomial space. This improves both the previous best 2- and 3-approximation algorithms of Cygan et al. which have an O(3^n) and O(2^n) worst-case time bounds, respectively. Our algorithm is based on constructing bucket decompositions of the input graph. A bucket decomposition partitions the vertex set of a graph into ordered sets (called buckets) of (almost) equal sizes such that all edges are either incident on vertices in the same bucket or on vertices in two consecutive buckets. The idea is to find the smallest bucket size for which there exists a bucket decomposition. The algorithm uses a simple divide-and-conquer strategy along with dynamic programming to achieve this improved time bound.

  13. Variable bandwidth and one-step local M-estimator

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    A robust version of local linear regression smoothers augmented with variable bandwidth is studied. The proposed method inherits the advantages of local polynomial regression and overcomes the shortcoming of lack of robustness of least-squares techniques. The use of variable bandwidth enhances the flexibility of the resulting local M-estimators and makes them possible to cope well with spatially inhomogeneous curves, heteroscedastic errors and nonuniform design densities. Under appropriate regularity conditions, it is shown that the proposed estimators exist and are asymptotically normal. Based on the robust estimation equation, one-step local M-estimators are introduced to reduce computational burden. It is demonstrated that the one-step local M-estimators share the same asymptotic distributions as the fully iterative M-estimators, as long as the initial estimators are good enough. In other words, the one-step local M-estimators reduce significantly the computation cost of the fully iterative M-estimators without deteriorating their performance. This fact is also illustrated via simulations.

  14. An exponential time 2-approximation algorithm for bandwidth

    Energy Technology Data Exchange (ETDEWEB)

    Kasiviswanathan, Shiva [Los Alamos National Laboratory; Furer, Martin [PENNSYLVANIA STATE U; Gaspers, Serge [U OF MONTPELLIER, FRANCE

    2009-01-01

    The bandwidth of a graph G on n vertices is the minimum b such that the vertices of G can be labeled from 1 to n such that the labels of every pair of adjacent vertices differ by at most b. In this paper, we present a 2-approximation algorithm for the Bandwidth problem that takes worst-case {Omicron}(1.9797{sup n}) = {Omicron}(3{sup 0.6217n}) time and uses polynomial space. This improves both the previous best 2- and 3-approximation algorithms of Cygan et al. which have an {Omicron}*(3{sup n}) and {Omicron}*(2{sup n}) worst-case time bounds, respectively. Our algorithm is based on constructing bucket decompositions of the input graph. A bucket decomposition partitions the vertex set of a graph into ordered sets (called buckets) of (almost) equal sizes such that all edges are either incident on vertices in the same bucket or on vertices in two consecutive buckets. The idea is to find the smallest bucket size for which there exists a bucket decomposition. The algorithm uses a simple divide-and-conquer strategy along with dynamic programming to achieve this improved time bound.

  15. Bandwidth Optimization in Centralized WLANs for Different Traffic Types

    Directory of Open Access Journals (Sweden)

    Haines RJ

    2007-01-01

    Full Text Available Allocating bandwidth between different forms of coexisting traffic (such as web-browsing, streaming, and telephony within a wireless LAN is a challenging and interesting problem. Centralized coordination functions in wireless LANs offer several advantages over distributed approaches, having the benefit of a system overview at the controller, but obtaining a stable configuration of bandwidth allocation for the system is nontrivial. We present, review, and compare different mechanisms to achieve this end, and a number of different means of obtaining the configurations themselves. We describe an analytical model of the system under consideration and present two mathematical approaches to derive solutions for any system configuration and deployment, along with an adaptive feedback-based solution. We also describe a comprehensive simulation-based model for the problem, and a prototype that allows comparison of these approaches. Our investigations demonstrate that a self-adaptive dynamic approach far outperforms any static scheme, and that using a mathematical model to produce the configurations themselves confers several advantages.

  16. High-Performance 1.55-µm Superluminescent Diode Based on Broad Gain InAs/InGaAlAs/InP Quantum Dash Active Region

    KAUST Repository

    Khan, Mohammed Zahed Mustafa

    2014-08-01

    We report on the high-performance characteristics from superluminescent diodes (SLDs) based on four-stack InAs/InGaAlAs chirped-barrier thickness quantum dash (Qdash) in a well structure. The active region exhibits a measured broad gain spectrum of 140 nm, with a peak modal gain of ~41 cm-1. The noncoated two-section gainabsorber broad-area and ridge-waveguide device configuration exhibits an output power of > 20 mW and > 12 mW, respectively. The corresponding -3-dB bandwidths span ~82 nm and ~72 nm, with a small spectral ripple of <; 0.2 dB, related largely to the contribution from dispersive height dash ensembles of the highly inhomogeneous active region. These C-L communication band devices will find applications in various cross-disciplinary fields of optical metrology, optical coherent tomography, etc.

  17. Active control system for high speed windmills

    Science.gov (United States)

    Avery, D.E.

    1988-01-12

    A pump stroke is matched to the operating speed of a high speed windmill. The windmill drives a hydraulic pump for a control. Changes in speed of a wind driven shaft open supply and exhaust valves to opposite ends of a hydraulic actuator to lengthen and shorten an oscillating arm thereby lengthening and shortening the stroke of an output pump. Diminishing wind to a stall speed causes the valves to operate the hydraulic cylinder to shorten the oscillating arm to zero. A pressure accumulator in the hydraulic system provides the force necessary to supply the hydraulic fluid under pressure to drive the actuator into and out of the zero position in response to the windmill shaft speed approaching and exceeding windmill stall speed. 4 figs.

  18. A new low voltage level-shifted FVF current mirror with enhanced bandwidth and output resistance

    Science.gov (United States)

    Aggarwal, Bhawna; Gupta, Maneesha; Gupta, Anil Kumar; Sangal, Ankur

    2016-10-01

    This paper proposes a new high-performance level-shifted flipped voltage follower (LSFVF) based low-voltage current mirror (CM). The proposed CM utilises the low-supply voltage and low-input resistance characteristics of a flipped voltage follower (FVF) CM. In the proposed CM, level-shifting configuration is used to obtain a wide operating current range and resistive compensation technique is employed to increase the operating bandwidth. The peaking in frequency response is reduced by using an additional large MOSFET. Moreover, a very high output resistance (in GΩ range) along with low-current transfer error is achieved through super-cascode configuration for a wide current range (0-440 µA). Small signal analysis is carried out to show the improvements achieved at each step. The proposed CM is simulated by Mentor Graphics Eldospice in TSMC 0.18 µm CMOS, BSIM3 and Level 53 technology. In the proposed CM, a bandwidth of 6.1799 GHz, 1% settling time of 0.719 ns, input and output resistances of 21.43 Ω and 1.14 GΩ, respectively, are obtained with a single supply voltage of 1 V. The layout of the proposed CM has been designed and post-layout simulation results have been shown. The post-layout simulation results for Monte Carlo and temperature analysis have also been included to show the reliability of the CM against the variations in process parameters and temperature changes.

  19. Self-calibrating ultra-low noise, wide-bandwidth optomechanical accelerometer

    CERN Document Server

    Cervantes, Felipe Guzman; Pratt, Jon; Taylor, Jacob

    2013-01-01

    The reflection spectrum of an optical cavity is exquisitely sensitive to length variations, enabling precise and accurate displacement measurements. When combined with mechanical oscillators, such cavities can yield accelerometers of unprecedented resolution. Previously, accelerometer sensitivity enhancements were achieved by lowering the sensor's natural frequency and bandwidth. Detection near the thermal limit was achieved, but at high acceleration levels due to low oscillator mass. We present a novel self-calibrating accelerometer, capable of reaching nano-gn/rtHz sensitivities (micro-Gal/rtHz -- 1gn=9.81 m/s^2 -- equivalent displacement of attometer/rtHz) over a bandwidth of several kHz, and compare its accuracy to a calibrated commercial system. It consists of a compact (10.6 x 15 mm), high-mQ (5kg) fused-silica oscillator that utilizes fiber-optic micro-mirror cavities, for self-calibrated detection of the motions of its test-mass. This device provides a substantial improvement over conventional systems...

  20. Design of RFID Cloud Services in a Low Bandwidth Network Environment

    Directory of Open Access Journals (Sweden)

    John P.T. Mo

    2011-02-01

    Full Text Available The use of Information and Communication Technologies has significantly improved the efficiency of modern supply chains. Existing IT architecture is too rigid to allow new technologies such as RFID technologies to be implemented. With the aid of virtualisation and integrated with cloud services, infrastructure hardware and network devices can be consolidated into a physical device, reducing the cost of ownership. However, for such cloud services model to work correctly, a high speed network is required between each site and the cloud service provider. This poses huge challenges for real‐time system such as RFID‐enabled supply chains. Since modern supply chains operate on a global platform, it is almost impossible to assure availability of high speed networks across the global supply chain. This paper proposes two solutions to supplement the virtualisation and cloud services model. A sub‐cloud services solution, where each service is distributed across multiple hosts across different countries and regions is proposed to enhance accessibility to higher bandwidth networks. The second solution is the Queued Burst Device Compression system incorporates a compression service that compresses RFID data sets into much smaller packages. This solution is proved to work by a multiple‐in‐single‐out queuing model and is suitable for low bandwidth networks such as GPRS and 3G wireless environmenst.

  1. Theoretical study of amplified spontaneous emission intensity and bandwidth reduction in polymer

    Institute of Scientific and Technical Information of China (English)

    A. Hariri; S. Sarikhani

    2015-01-01

    Amplified spontaneous emission (ASE), including intensity and bandwidth, in a typical example of BuEH-PPV is calculated. For this purpose, the intensity rate equation is used to explain the reported experimental measurements of a BuEH-PPV sample pumped at different pump intensities from Ip=0.61 MW/cm2 to 5.2 MW/cm2. Both homogeneously and inhomogeneously broadened transition lines along with a model based on the geometrically dependent gain coefficient (GDGC) are examined and it is confirmed that for the reported measurements the homogeneously broadened line is respon-sible for the light–matter interaction. The calculation explains the frequency spectrum of the ASE output intensity extracted from the sample at different pump intensities, unsaturated and saturated gain coefficients, and ASE bandwidth reduction along the propagation direction. Both analytical and numerical calculations for verifying the GDGC model are presented in this paper. Although the introduced model has shown its potential for explaining the ASE behavior in a specific sample it can be universally used for the ASE study in different active media.

  2. Ultrahigh Responsivity-Bandwidth Product in a Compact InP Nanopillar Phototransistor Directly Grown on Silicon

    Science.gov (United States)

    Ko, Wai Son; Bhattacharya, Indrasen; Tran, Thai-Truong D.; Ng, Kar Wei; Adair Gerke, Stephen; Chang-Hasnain, Connie

    2016-09-01

    Highly sensitive and fast photodetectors can enable low power, high bandwidth on-chip optical interconnects for silicon integrated electronics. III-V compound semiconductor direct-bandgap materials with high absorption coefficients are particularly promising for photodetection in energy-efficient optical links because of the potential to scale down the absorber size, and the resulting capacitance and dark current, while maintaining high quantum efficiency. We demonstrate a compact bipolar junction phototransistor with a high current gain (53.6), bandwidth (7 GHz) and responsivity (9.5 A/W) using a single crystalline indium phosphide nanopillar directly grown on a silicon substrate. Transistor gain is obtained at sub-picowatt optical power and collector bias close to the CMOS line voltage. The quantum efficiency-bandwidth product of 105 GHz is the highest for photodetectors on silicon. The bipolar junction phototransistor combines the receiver front end circuit and absorber into a monolithic integrated device, eliminating the wire capacitance between the detector and first amplifier stage.

  3. Ultrahigh Responsivity-Bandwidth Product in a Compact InP Nanopillar Phototransistor Directly Grown on Silicon

    Science.gov (United States)

    Ko, Wai Son; Bhattacharya, Indrasen; Tran, Thai-Truong D.; Ng, Kar Wei; Adair Gerke, Stephen; Chang-Hasnain, Connie

    2016-01-01

    Highly sensitive and fast photodetectors can enable low power, high bandwidth on-chip optical interconnects for silicon integrated electronics. III-V compound semiconductor direct-bandgap materials with high absorption coefficients are particularly promising for photodetection in energy-efficient optical links because of the potential to scale down the absorber size, and the resulting capacitance and dark current, while maintaining high quantum efficiency. We demonstrate a compact bipolar junction phototransistor with a high current gain (53.6), bandwidth (7 GHz) and responsivity (9.5 A/W) using a single crystalline indium phosphide nanopillar directly grown on a silicon substrate. Transistor gain is obtained at sub-picowatt optical power and collector bias close to the CMOS line voltage. The quantum efficiency-bandwidth product of 105 GHz is the highest for photodetectors on silicon. The bipolar junction phototransistor combines the receiver front end circuit and absorber into a monolithic integrated device, eliminating the wire capacitance between the detector and first amplifier stage. PMID:27659796

  4. Ultrawide Bandwidth Receiver Based on a Multivariate Generalized Gaussian Distribution

    KAUST Repository

    Ahmed, Qasim Zeeshan

    2015-04-01

    Multivariate generalized Gaussian density (MGGD) is used to approximate the multiple access interference (MAI) and additive white Gaussian noise in pulse-based ultrawide bandwidth (UWB) system. The MGGD probability density function (pdf) is shown to be a better approximation of a UWB system as compared to multivariate Gaussian, multivariate Laplacian and multivariate Gaussian-Laplacian mixture (GLM). The similarity between the simulated and the approximated pdf is measured with the help of modified Kullback-Leibler distance (KLD). It is also shown that MGGD has the smallest KLD as compared to Gaussian, Laplacian and GLM densities. A receiver based on the principles of minimum bit error rate is designed for the MGGD pdf. As the requirement is stringent, the adaptive implementation of the receiver is also carried out in this paper. Training sequence of the desired user is the only requirement when implementing the detector adaptively. © 2002-2012 IEEE.

  5. Bandwidth Reservation Using Velocity and Handoff Statistics for Cellular Networks

    Institute of Scientific and Technical Information of China (English)

    Chuan-Lin Zhang; Kam Yiu Lam; Wei-Jia Jia

    2006-01-01

    The percentages of blocking and forced termination rates as parameters representing quality of services (QoS)requirements are presented. The relation between the connection statistics of mobile users in a cell and the handoff number and new call number in next duration in each cell is explored. Based on the relation, statistic reservation tactics are raised.The amount of bandwidth for new calls and handoffs of each cell in next period is determined by using the strategy. Using this method can guarantee the communication system suits mobile connection request dynamic. The QoS parameters:forced termination rate and blocking rate can be maintained steadily though they may change with the offered load. Some numerical experiments demonstrate this is a practical method with affordable overhead.

  6. Graphene metascreen for designing compact infrared absorbers with enhanced bandwidth

    KAUST Repository

    Chen, Pai-Yen

    2015-03-31

    We propose a compact, wideband terahertz and infrared absorber, comprising a patterned graphene sheet on a thin metal-backed dielectric slab. This graphene-based nanostructure can achieve a low or negative effective permeability, necessary for realizing the perfect absorption. The dual-reactive property found in both the plasmonic graphene sheet and the grounded highpermittivity slab introduces extra poles into the equivalent circuit model of the system, thereby resulting in a dual-band or broadband magnetic resonance that enhances the absorption bandwidth. More interestingly, the two-dimensional patterned graphene sheet significantly simplifies the design and fabrication processes for achieving resonant magnetic response, and allows the frequency-reconfigurable operation via electrostatic gating.

  7. Acousto-optical interaction bandwidth of more than 2 GHz

    Science.gov (United States)

    Petrov, Vladimir V.

    1996-12-01

    The way of extension of acousto-optical interaction frequency bandwidth to more than one octave is suggested. The main principle used for this aim is to design the electro-acoustical multi-element transducer with variable, along its length, parameters. In such a case to each frequency point inside chosen band exists the region of the transducer's length where, from one hand, the condition for good excitation of sound waves is fulfilled and from the other hand the Bragg condition is also fulfilled because of closed coincidence of real and necessary frequency dependencies of Bragg angle and of the angle of sound wave front inclination. This window moves from one end of the transducer to the other when frequency changes from minimum to maximum one inside the band. The closer real angle frequency dependence follows to necessary one than larger the length of transducer can be done and than more higher the diffraction efficiency can be reached.

  8. UNIFORM—PRICE AUCTION FOR BANDWIDTH ALLOCATION IN THE INTERNET

    Institute of Scientific and Technical Information of China (English)

    WeiJiaolong; ZhangChi

    2002-01-01

    It has been widely accepted that auctioning which is the pricing approach with minimal information requirement is a proper tool to manage scare network resources.Previous works focus on vickrey auction which is incentive compatible in classic auction theory.In the beginning of this letter,the faults of the most representative auction-based mechanisms are discussed.And then a new method called Uniform-Price Auction(UPA),which has the simplest auctiopn rule is proposed and its incentive compatibility in the network environment is also proved.Finally,the basic mode is extended to support applications which require minimum bandwidth guarantees for a given time period by introducing derivative market.and a market mechanism for network resource allocation which is predictable,riskless,and simple for eng-users is completed.

  9. Auction-based bandwidth allocation in the Internet

    Science.gov (United States)

    Wei, Jiaolong; Zhang, Chi

    2002-07-01

    It has been widely accepted that auctioning which is the pricing approach with minimal information requirement is a proper tool to manage scare network resources. Previous works focus on Vickrey auction which is incentive compatible in classic auction theory. In the beginning of this paper, the faults of the most representative auction-based mechanisms are discussed. And then a new method called uniform-price auction (UPA), which has the simplest auction rule is proposed and it's incentive compatibility in the network environment is also proved. Finally, the basic mode is extended to support applications which require minimum bandwidth guarantees for a given time period by introducing derivative market, and a market mechanism for network resource allocation which is predictable, riskless, and simple for end-users is completed.

  10. UNIFORM-PRICE AUCTION FOR BANDWIDTH ALLOCATION IN THE INTERNET

    Institute of Scientific and Technical Information of China (English)

    Wei Jiaolong; Zhang Chi

    2002-01-01

    It has been widely accepted that auctioning which is the pricing approach with minimal information requirement is a proper tool to manage scare network resources. Previous works focus on Vickrey auction which is incentive compatible in classic auction theory. In the beginning of this letter, the faults of the most representative auction-based mechanisms are discussed. And then a new method called Uniform-Price Auction (UPA), which has the simplest auction rule is proposed and its incentive compatibility in the network environment is also proved. Finally, the basic mode is extended to support applications which require minimum bandwidth guarantees for a given time period by introducing derivative market, and a market mechanism for network resource allocation which is predictable, riskless, and simple for end-users is completed.

  11. An improved harmony search algorithm with dynamically varying bandwidth

    Science.gov (United States)

    Kalivarapu, J.; Jain, S.; Bag, S.

    2016-07-01

    The present work demonstrates a new variant of the harmony search (HS) algorithm where bandwidth (BW) is one of the deciding factors for the time complexity and the performance of the algorithm. The BW needs to have both explorative and exploitative characteristics. The ideology is to use a large BW to search in the full domain and to adjust the BW dynamically closer to the optimal solution. After trying a series of approaches, a methodology inspired by the functioning of a low-pass filter showed satisfactory results. This approach was implemented in the self-adaptive improved harmony search (SIHS) algorithm and tested on several benchmark functions. Compared to the existing HS algorithm and its variants, SIHS showed better performance on most of the test functions. Thereafter, the algorithm was applied to geometric parameter optimization of a friction stir welding tool.

  12. Wide modulation bandwidth terahertz detection in 130 nm CMOS technology

    Science.gov (United States)

    Nahar, Shamsun; Shafee, Marwah; Blin, Stéphane; Pénarier, Annick; Nouvel, Philippe; Coquillat, Dominique; Safwa, Amr M. E.; Knap, Wojciech; Hella, Mona M.

    2016-11-01

    Design, manufacturing and measurements results for silicon plasma wave transistors based wireless communication wideband receivers operating at 300 GHz carrier frequency are presented. We show the possibility of Si-CMOS based integrated circuits, in which by: (i) specific physics based plasma wave transistor design allowing impedance matching to the antenna and the amplifier, (ii) engineering the shape of the patch antenna through a stacked resonator approach and (iii) applying bandwidth enhancement strategies to the design of integrated broadband amplifier, we achieve an integrated circuit of the 300 GHz carrier frequency receiver for wireless wideband operation up to/over 10 GHz. This is, to the best of our knowledge, the first demonstration of low cost 130 nm Si-CMOS technology, plasma wave transistors based fast/wideband integrated receiver operating at 300 GHz atmospheric window. These results pave the way towards future large scale (cost effective) silicon technology based terahertz wireless communication receivers.

  13. Adaptive Data Filtering of Inertial Sensors with Variable Bandwidth

    Science.gov (United States)

    Alam, Mushfiqul; Rohac, Jan

    2015-01-01

    MEMS (micro-electro-mechanical system)-based inertial sensors, i.e., accelerometers and angular rate sensors, are commonly used as a cost-effective solution for the purposes of navigation in a broad spectrum of terrestrial and aerospace applications. These tri-axial inertial sensors form an inertial measurement unit (IMU), which is a core unit of navigation systems. Even if MEMS sensors have an advantage in their size, cost, weight and power consumption, they suffer from bias instability, noisy output and insufficient resolution. Furthermore, the sensor's behavior can be significantly affected by strong vibration when it operates in harsh environments. All of these constitute conditions require treatment through data processing. As long as the navigation solution is primarily based on using only inertial data, this paper proposes a novel concept in adaptive data pre-processing by using a variable bandwidth filtering. This approach utilizes sinusoidal estimation to continuously adapt the filtering bandwidth of the accelerometer's data in order to reduce the effects of vibration and sensor noise before attitude estimation is processed. Low frequency vibration generally limits the conditions under which the accelerometers can be used to aid the attitude estimation process, which is primarily based on angular rate data and, thus, decreases its accuracy. In contrast, the proposed pre-processing technique enables using accelerometers as an aiding source by effective data smoothing, even when they are affected by low frequency vibration. Verification of the proposed concept is performed on simulation and real-flight data obtained on an ultra-light aircraft. The results of both types of experiments confirm the suitability of the concept for inertial data pre-processing. PMID:25648711

  14. Adaptive Data Filtering of Inertial Sensors with Variable Bandwidth

    Directory of Open Access Journals (Sweden)

    Mushfiqul Alam

    2015-02-01

    Full Text Available MEMS (micro-electro-mechanical system-based inertial sensors, i.e., accelerometers and angular rate sensors, are commonly used as a cost-effective solution for the purposes of navigation in a broad spectrum of terrestrial and aerospace applications. These tri-axial inertial sensors form an inertial measurement unit (IMU, which is a core unit of navigation systems. Even if MEMS sensors have an advantage in their size, cost, weight and power consumption, they suffer from bias instability, noisy output and insufficient resolution. Furthermore, the sensor’s behavior can be significantly affected by strong vibration when it operates in harsh environments. All of these constitute conditions require treatment through data processing. As long as the navigation solution is primarily based on using only inertial data, this paper proposes a novel concept in adaptive data pre-processing by using a variable bandwidth filtering. This approach utilizes sinusoidal estimation to continuously adapt the filtering bandwidth of the accelerometer’s data in order to reduce the effects of vibration and sensor noise before attitude estimation is processed. Low frequency vibration generally limits the conditions under which the accelerometers can be used to aid the attitude estimation process, which is primarily based on angular rate data and, thus, decreases its accuracy. In contrast, the proposed pre-processing technique enables using accelerometers as an aiding source by effective data smoothing, even when they are affected by low frequency vibration. Verification of the proposed concept is performed on simulation and real-flight data obtained on an ultra-light aircraft. The results of both types of experiments confirm the suitability of the concept for inertial data pre-processing.

  15. Narrow-Bandwidth Diode-Laser-Based Ultraviolet Light Source

    Institute of Scientific and Technical Information of China (English)

    PENG Yu; FANG Zhan-Jun; ZANG Er-Jun

    2011-01-01

    A compact, tunable and narrow-bandwidth laser source for ultraviolet radiation is presented. A grating stabilized diode laser at 1064 nm is frequency-stabilized to below 10 kHz by using a ultra low expansion (ULE) cavity. Injecting light of the diode laser into a tapered amplifier yields a power of 290mW. In a first frequency-doubling stage, about 47 mW of green light at 532nm is generated by using a periodical// poled KTP crystal. Subsequent second-harwonic generation employing a BBO crystal leads to about 30μW of ultraviolet light at 266nm.%A compact,tunable and narrow-bandwidth laser source for ultraviolet radiation is presented.A grating stabilized diode laser at 1064nm is frequency-stabilized to below 10kHz by using a ultra low expansion (ULE) cavity.Injecting light of the diode laser into a tapered amplifier yields a power of 290 mW.In a first frequency-doubling stage,about 47mW of green light at 532nm is generated by using a periodically poled KTP crystal.Subsequent second-harmonic generation employing a BBO crystal leads to about 30 μ W of ultraviolet light at 266nm.Hg is,so far,the heaviest nonradioactive atom that has been laser-cooled and trapped.Systematic evaluation of various sources of uncertainty for the Hg-based optical lattice clock is obtained and an accuracy of better than 10-1s is attainable,which is an order of magnitude of improvement over Sr or Yb based clocks because of the reduced susceptibility to the blackbody radiation field,which sets a major limitation on the accuracy of atomic clocks.[1] The 1S0-3p0 transition at 265.6 nm will be exploited as a clock transition.

  16. Bandwidth optimization design of a multi degree of freedom MEMS gyroscope.

    Science.gov (United States)

    Si, Chaowei; Han, Guowei; Ning, Jin; Yang, Fuhua

    2013-08-14

    A new robust multi-degree of freedom (multi-DOF) MEMS gyroscope is presented in this paper. The designed gyroscope has its bandwidth and amplification factor of the sense mode adjusted more easily than the previous reported multi-DOF MEMS gyroscopes. Besides, a novel spring system with very small coupling stiffness is proposed, which helps achieve a narrow bandwidth and a high amplification factor for a 2-DOF vibration system. A multi-DOF gyroscope with the proposed weak spring system is designed, and simulations indicate that when the operating frequency is set at 12.59 kHz, the flat frequency response region of the sense mode can be designed as narrow as 80 Hz, and the amplification factor of the sense mode at the operating frequency is up to 91, which not only protects the amplification factor from instability against process and temperature variations, but also sacrifices less performance. An experiment is also carried out to demonstrate the validity of the design. The multi-DOF gyroscope with the proposed weak coupling spring system is capable of achieving a good tradeoff between robustness and the performance.

  17. Bandwidth Optimization Design of a Multi Degree of Freedom MEMS Gyroscope

    Directory of Open Access Journals (Sweden)

    Fuhua Yang

    2013-08-01

    Full Text Available A new robust multi-degree of freedom (multi-DOF MEMS gyroscope is presented in this paper. The designed gyroscope has its bandwidth and amplification factor of the sense mode adjusted more easily than the previous reported multi-DOF MEMS gyroscopes. Besides, a novel spring system with very small coupling stiffness is proposed, which helps achieve a narrow bandwidth and a high amplification factor for a 2-DOF vibration system. A multi-DOF gyroscope with the proposed weak spring system is designed, and simulations indicate that when the operating frequency is set at 12.59 kHz, the flat frequency response region of the sense mode can be designed as narrow as 80 Hz, and the amplification factor of the sense mode at the operating frequency is up to 91, which not only protects the amplification factor from instability against process and temperature variations, but also sacrifices less performance. An experiment is also carried out to demonstrate the validity of the design. The multi-DOF gyroscope with the proposed weak coupling spring system is capable of achieving a good tradeoff between robustness and the performance.

  18. Bandwidth enhancement of electro-optic field sensing using photonic down-mixing with harmonic sidebands.

    Science.gov (United States)

    Lee, Dong-Joon; Whitaker, John F

    2008-09-15

    We demonstrate that harmonic sidebands of an electro-optic modulator's driving frequency can be used as the local oscillator in a photonic down-mixing process in order to significantly enhance the bandwidth of near-field, electro-optic, microwave measurements. The creation of second- and third-order-harmonic modulation sidebands on a laser-diode output are described, with heterodyne down-conversion of microwave signals taking place within an electro-optic sensor crystal. The measurement bandwidth of an electro-optic microwave probe can thus be enhanced by as much as a factor of three with respect to the use of conventional, fundamental-harmonic sidebands. Carrier-sideband analysis from the measured optical spectrum indicates that millimeter-wave-frequency local-oscillator sidebands can be created using a Ku-band electro-optic modulator and that the electro-optic-signal-modulation depth can be enhanced by suppressing the light-beam carrier component. Transverse near-field distributions from high frequency patch antennas are extracted using both second- and third-order-harmonic sidebands.

  19. Bandwidth enhancement of a dual band planar monopole antenna using meandered microstrip feeding.

    Science.gov (United States)

    Ahsan, M R; Islam, M T; Habib Ullah, M; Misran, N

    2014-01-01

    A meandered-microstrip fed circular shaped monopole antenna loaded with vertical slots on a high dielectric material substrate (ε r = 15) is proposed in this paper. The performance criteria of the proposed antenna have been experimentally verified by fabricating a printed prototype. The experimental results show that the proposed antenna has achieved wider bandwidth with satisfactory gain by introducing meandered-microstrip feeding in assistant of partial ground plane. It is observed that, the -10 dB impedance bandwidth of the proposed antenna at lower band is 44.4% (600 MHz-1 GHz) and at upper band is 28% (2.25 GHz-2.95 GHz). The measured maximum gains of -1.18 dBi and 4.87 dBi with maximum radiation efficiencies have been observed at lower band and upper band, respectively. The antenna configuration and parametric study have been carried out with the help of commercially available computer-aided EM simulator, and a good accordance is perceived in between the simulated and measured results. The analysis of performance criteria and almost consistent radiation pattern make the proposed antenna a suitable candidate for UHF RFID, WiMAX, and WLAN applications.

  20. High contrast imaging with an arbitrary aperture: active correction of aperture discontinuities: fundamental limits and practical trade- offs

    Science.gov (United States)

    Pueyo, Laurent; Norman, Colin; Soummer, Rémi; Perrin, Marshall; N'Diaye, Mamadou; Choquet, Élodie; Hoffmann, Jordan; Carlotti, Alexis; Mawet, Dimitri

    2014-08-01

    We present a new method to achieve high-contrast images using segmented and/or on-axis telescopes. Our approach relies on using two sequential Deformable Mirrors to compensate for the large amplitude excursions in the telescope aperture due to secondary support structures and / or segment gaps. We solve the highly non-linear Monge-Ampere equation that is the fundamental equation describing the physics of phase induced amplitude modulation. We determine the optimum configuration for our two sequential Deformable Mirror system and show that high-throughput and high contrast solutions can be achieved using realistic surface deformations that are accessible using existing technologies. We name this process Active Compensation of Aperture Discontinuities (ACAD). We show that for geometries similar to JWST, ACAD can attain at least 10-7 in contrast and an order of magnitude higher for future Extremely Large Telescopes, even when the pupil features a "missing segment" . Because the converging non-linear mappings resulting from our Deformable Mirror shapes damps near-field diffraction artifacts in the vicinity of the discontinuities this solution is particularly appealing in terms of spectral bandwidth. We present preliminary results that illustrate the performances of ACAD in the presence of diffraction for apertures for with secondary support structures of varying width and argue that the ultimate contrast achieved can by combining ACAD with modern wavefront control algorithms.

  1. Catalytically highly active top gold atom on palladium nanocluster.

    Science.gov (United States)

    Zhang, Haijun; Watanabe, Tatsuya; Okumura, Mitsutaka; Haruta, Masatake; Toshima, Naoki

    2011-10-23

    Catalysis using gold is emerging as an important field of research in connection with 'green' chemistry. Several hypotheses have been presented to explain the markedly high activities of Au catalysts. So far, the origin of the catalytic activities of supported Au catalysts can be assigned to the perimeter interfaces between Au nanoclusters and the support. However, the genesis of the catalytic activities of colloidal Au-based bimetallic nanoclusters is unclear. Moreover, it is still a challenge to synthesize Au-based colloidal catalysts with high activity. Here we now present the 'crown-jewel' concept (Supplementary Fig. S1) for preparation of catalytically highly Au-based colloidal catalysts. Au-Pd colloidal catalysts containing an abundance of top (vertex or corner) Au atoms were synthesized according to the strategy on a large scale. Our results indicate that the genesis of the high activity of the catalysts could be ascribed to the presence of negatively charged top Au atoms.

  2. Identification of highly active flocculant proteins in bovine blood.

    Science.gov (United States)

    Piazza, George J; Nuñez, Alberto; Garcia, Rafael A

    2012-03-01

    Synthetic polymeric flocculants are used extensively for wastewater remediation, soil stabilization, and reduction in water leakage from unlined canals. Sources of highly active, inexpensive, renewable flocculants are needed to replace synthetic flocculants. High kaolin flocculant activity was documented for bovine blood (BB) and blood plasma with several anticoagulant treatments. BB serum also had high flocculant activity. To address the hypothesis that some blood proteins have strong flocculating activity, the BB proteins were separated by SEC. Then, the major proteins of the flocculant-active fractions were separated by SDS-PAGE. Identity of the major protein components was determined by tryptic digestion and peptide analysis by MALDI TOF MS. The sequence of selected peptides was confirmed using TOF/TOF-MS/MS fragmentation. Hemoglobin dimer (subunits α and β) was identified as the major protein component of the active fraction in BB; its high flocculation activity was confirmed by testing a commercial sample of hemoglobin. In the same manner, three proteins from blood plasma (fibrinogen, γ-globulin, α-2-macroglobulin) were found to be highly active flocculants, but bovine serum albumin, α-globulin, and β-globulin were not flocculants. On a mass basis, hemoglobin, γ-globulin, α-2-macroglobulin were as effective as anionic polyacrylamide (PAM), a widely used synthetic flocculant. The blood proteins acted faster than PAM, and unlike PAM, the blood proteins flocculants did not require calcium salts for their activity.

  3. Social capital and physical activity among Croatian high school students.

    Science.gov (United States)

    Novak, D; Doubova, S V; Kawachi, I

    2016-06-01

    To examine factors associated with regular physical activity in Croatian adolescents. A cross-sectional survey among high school students was carried out in the 2013/14 school year. A survey was conducted among 33 high schools in Zagreb City, Croatia. Participants were students aged 17-18 years. The dependent variables were regular moderate to vigorous physical activity (MVPA) and overall physical activity measured by the short version of International Physical Activity Questionnaire and defined as 60 min or more of daily physical activity. The independent variables included family, neighborhood, and high school social capital. Other study covariates included: socio-economic status, self-rated health, psychological distress and nutritional status. The associations between physical activity and social capital variables were assessed separately for boys and girls through multiple logistic regression and inverse probability weighting in order to correct for missing data bias. A total of 1689 boys and 1739 girls responded to the survey. A higher percentage of boys reported performing regular vigorous and moderate physical activity (59.4%) and overall physical activity (83.4%), comparing with the girls (35.4% and 70%, respectively). For boys, high family social capital and high informal social control were associated with increased odds of regular MVPA (1.49, 95%CI: 1.18 - 1.90 and 1.26, 95%CI: 1.02 - 1.56, respectively), compared to those with low social capital. For girls, high informal social control was associated with regular overall physical activity (OR 1.38, 95% CI: 1.09 - 1.76). High social capital is associated with regular MVPA in boys and regular overall activity in girls. Intervention and policies that leverage community social capital might serve as an avenue for promotion of physical activity in youth. Copyright © 2016 The Royal Society for Public Health. Published by Elsevier Ltd. All rights reserved.

  4. A variable bandwidth assignment scheme for the Land Mobile Satellite experiment

    Science.gov (United States)

    Yan, T.-Y.; Li, V. O. K.

    The Mobile Satellite Experiment is a proposed experimental satellite-based communications network which provides data and voice communications to mobile terminals dispersed in geographically dispersed areas. In this paper, an analytical model is developed to calculate the performance of a Variable Bandwidth Assignment (VBA) Scheme. Under this scheme, the satellite channel bandwidth is dynamically reassigned so that a message may be transmitted in the shortest possible time. To transmit a long message, message channels will be reconfigured to have more bandwidth such that the transmission time is reduced, while to transmit a short message, the channel bandwidth will be shrunk such that the released bandwidth can be used to serve other messages. The model is illustrated with numerical examples. It is shown that a VBA scheme can achieve considerable improvement in transmission delays over a Fixed Bandwidth Assignment Scheme.

  5. Measuring End-To-End Bandwidth with Iperf Using Web100

    Energy Technology Data Exchange (ETDEWEB)

    Cottrell, Les

    2003-04-30

    End-to-end bandwidth estimation tools like Iperf though fairly accurate are intrusive. In this paper, we describe how with an instrumented TCP stack (Web100), we can estimate the end-to-end bandwidth accurately, while consuming significantly less network bandwidth and time. We modified Iperf to use Web100 to detect the end of slow-start and estimate the end-to-end bandwidth by measuring the amount of data sent for a short period (1 second) after the slow-start, when the TCP throughput is relatively stable. We obtained bandwidth estimates differing by less than 10% when compared to running Iperf for 20 seconds, and savings in bandwidth estimation time of up to 94% and savings in network traffic of up to 92%.

  6. ±25ppm repeatable measurement of trapezoidal pulses with 5MHz bandwidth

    CERN Document Server

    AUTHOR|(SzGeCERN)712364; Arpaia, Pasquale; Cerqueira Bastos, Miguel; Martino, Michele

    2015-01-01

    High-quality measurements of pulses are nowadays widely used in fields such as radars, pulsed lasers, electromagnetic pulse generators, and particle accelerators. Whilst literature is mainly focused on fast systems for nanosecond regime with relaxed metrological requirements, in this paper, the high-performance measurement of slower pulses in microsecond regime is faced. In particular, the experimental proof demonstration for a 15 MS/s,_25 ppm repeatable acquisition system to characterize the flat-top of 3 ms rise-time trapezoidal pulses is given. The system exploits a 5MHz bandwidth circuit for analogue signal processing based on the concept of flat-top removal. The requirements, as well as the conceptual and physical designs are illustrated. Simulation results aimed at assessing the circuit performance are also presented. Finally, an experimental case study on the characterization of a pulsed power supply for the klystrons modulators of the Compact Linear Collider (CLIC) under study at CERN is reported. In ...

  7. Bandwidth Enhancement between Graphics Processing Units on the Peripheral Component Interconnect Bus

    Directory of Open Access Journals (Sweden)

    ANTON Alin

    2015-10-01

    Full Text Available General purpose computing on graphics processing units is a new trend in high performance computing. Present day applications require office and personal supercomputers which are mostly based on many core hardware accelerators communicating with the host system through the Peripheral Component Interconnect (PCI bus. Parallel data compression is a difficult topic but compression has been used successfully to improve the communication between parallel message passing interface (MPI processes on high performance computing clusters. In this paper we show that special pur pose compression algorithms designed for scientific floating point data can be used to enhance the bandwidth between 2 graphics processing unit (GPU devices on the PCI Express (PCIe 3.0 x16 bus in a homebuilt personal supercomputer (PSC.

  8. Dual Polarized near Field Probe Based on OMJ in Waveguide Technology Achieving More Than Octave Bandwidth

    DEFF Research Database (Denmark)

    Foged, L. J.; Giacomini, A.; Morbidini, R.

    2014-01-01

    In classic probe-corrected spherical NF measurements, one of the main concerns is the probe [1], [2], [3]. Standard NF-FF transformation software applies probe correction with the assumption that the probe pattern behaves with μ=±1 azimuthal dependence. In reality, any physically realizable probe...... is just an approximation to this ideal case. Probe excitation errors, finite manufacturing tolerances and probe interaction with the mounting interface and absorbers are examples of uncertainties that can lead to presence of higher-order spherical modes in the probe pattern [4], [5]. Although probe...... correction techniques for high-order probes are feasible [6], they are highly demanding in terms of implementation complexity as well as in terms of calibration and post-processing time. In this paper, a new OMJ designed entirely in waveguide and capable of covering more than an octave bandwidth is presented...

  9. Electro-optic dual-comb interferometry over 40-nm bandwidth

    CERN Document Server

    Duran, Vicente; Torres-Company, Victor

    2016-01-01

    Dual-comb interferometry is a measurement technique that uses two laser frequency combs to retrieve complex spectra in a line-by-line basis. This technique can be implemented with electro-optic frequency combs, offering intrinsic mutual coherence, high acquisition speed and flexible repetition-rate operation. A challenge with the operation of this kind of frequency comb in dual-comb interferometry is its limited optical bandwidth. Here, we use coherent spectral broadening and demonstrate electro-optic dual-comb interferometry over the entire telecommunications C band (200 lines covering ~ 40 nm, measured within 10 microseconds at 100 signal-to-noise ratio per spectral line). These results offer new prospects for electro-optic dual-comb interferometry as a suitable technology for high-speed broadband metrology, for example in optical coherence tomography or coherent Raman microscopy.

  10. Bandwidth manipulation of quantum light by an electro-optic time lens

    CERN Document Server

    Karpinski, Michal; Wright, Laura J; Smith, Brian J

    2016-01-01

    The ability to manipulate the spectral-temporal waveform of optical pulses has enabled a wide range of applications from ultrafast spectroscopy to high-speed communications. Extending these concepts to quantum light has the potential to enable breakthroughs in optical quantum science and technology. However, filtering and amplifying often employed in classical pulse shaping techniques are incompatible with non-classical light. Controlling the pulsed mode structure of quantum light requires efficient means to achieve deterministic, unitary manipulation that preserves fragile quantum coherences. Here we demonstrate an electro-optic method for modifying the spectrum of non-classical light by employing a time lens. In particular we show highly-efficient wavelength-preserving six-fold compression of single-photon spectral intensity bandwidth, enabling over a two-fold increase of single-photon flux into a spectrally narrowband absorber. These results pave the way towards spectral-temporal photonic quantum informati...

  11. Bandwidth-Aware Scheduling of Workflow Application on Multiple Grid Sites

    Directory of Open Access Journals (Sweden)

    Harshadkumar B. Prajapati

    2014-01-01

    Full Text Available Bandwidth-aware workflow scheduling is required to improve the performance of a workflow application in a multisite Grid environment, as the data movement cost between two low-bandwidth sites can adversely affect the makespan of the application. Pegasus WMS, an open-source and freely available WMS, cannot fully utilize its workflow mapping capability due to unavailability of integration of any bandwidth monitoring infrastructure in it. This paper develops the integration of Network Weather Service (NWS in Pegasus WMS to enable the bandwidth-aware mapping of scientific workflows. Our work demonstrates the applicability of the integration of NWS by making existing Heft site-selector of Pegasus WMS bandwidth aware. Furthermore, this paper proposes and implements a new workflow scheduling algorithm—Level based Highest Input and Processing Weight First. The results of the performed experiments indicate that the bandwidth-aware workflow scheduling algorithms perform better than bandwidth-unaware algorithms: Random and Heft of Pegasus WMS. Moreover, our proposed workflow scheduling algorithm performs better than the bandwidth-aware Heft algorithms. Thus, the proposed bandwidth-aware workflow scheduling enhances capability of Pegasus WMS and can increase performance of workflow applications.

  12. The Prediction of Bandwidth On Need Computer Network Through Artificial Neural Network Method of Backpropagation

    Directory of Open Access Journals (Sweden)

    Ikhthison Mekongga

    2014-02-01

    Full Text Available The need for bandwidth has been increasing recently. This is because the development of internet infrastructure is also increasing so that we need an economic and efficient provider system. This can be achieved through good planning and a proper system. The prediction of the bandwidth consumption is one of the factors that support the planning for an efficient internet service provider system. Bandwidth consumption is predicted using ANN. ANN is an information processing system which has similar characteristics as the biologic al neural network.  ANN  is  chosen  to  predict  the  consumption  of  the  bandwidth  because  ANN  has  good  approachability  to  non-linearity.  The variable used in ANN is the historical load data. A bandwidth consumption information system was built using neural networks  with a backpropagation algorithm to make the use of bandwidth more efficient in the future both in the rental rate of the bandwidth and in the usage of the bandwidth.Keywords: Forecasting, Bandwidth, Backpropagation

  13. Minimum cost maximum flow algorithm for upstream bandwidth allocation in OFDMA passive optical networks

    Science.gov (United States)

    Wu, Yating; Kuang, Bin; Wang, Tao; Zhang, Qianwu; Wang, Min

    2015-12-01

    This paper presents a minimum cost maximum flow (MCMF) based upstream bandwidth allocation algorithm, which supports differentiated QoS for orthogonal frequency division multiple access passive optical networks (OFDMA-PONs). We define a utility function as the metric to characterize the satisfaction degree of an ONU on the obtained bandwidth. The bandwidth allocation problem is then formulated as maximizing the sum of the weighted total utility functions of all ONUs. By constructing a flow network graph, we obtain the optimized bandwidth allocation using the MCMF algorithm. Simulation results show that the proposed scheme improves the performance in terms of mean packet delay, packet loss ratio and throughput.

  14. Network coding based joint signaling and dynamic bandwidth allocation scheme for inter optical network unit communication in passive optical networks

    Science.gov (United States)

    Wei, Pei; Gu, Rentao; Ji, Yuefeng

    2014-06-01

    As an innovative and promising technology, network coding has been introduced to passive optical networks (PON) in recent years to support inter optical network unit (ONU) communication, yet the signaling process and dynamic bandwidth allocation (DBA) in PON with network coding (NC-PON) still need further study. Thus, we propose a joint signaling and DBA scheme for efficiently supporting differentiated services of inter ONU communication in NC-PON. In the proposed joint scheme, the signaling process lays the foundation to fulfill network coding in PON, and it can not only avoid the potential threat to downstream security in previous schemes but also be suitable for the proposed hybrid dynamic bandwidth allocation (HDBA) scheme. In HDBA, a DBA cycle is divided into two sub-cycles for applying different coding, scheduling and bandwidth allocation strategies to differentiated classes of services. Besides, as network traffic load varies, the entire upstream transmission window for all REPORT messages slides accordingly, leaving the transmission time of one or two sub-cycles to overlap with the bandwidth allocation calculation time at the optical line terminal (the OLT), so that the upstream idle time can be efficiently eliminated. Performance evaluation results validate that compared with the existing two DBA algorithms deployed in NC-PON, HDBA demonstrates the best quality of service (QoS) support in terms of delay for all classes of services, especially guarantees the end-to-end delay bound of high class services. Specifically, HDBA can eliminate queuing delay and scheduling delay of high class services, reduce those of lower class services by at least 20%, and reduce the average end-to-end delay of all services over 50%. Moreover, HDBA also achieves the maximum delay fairness between coded and uncoded lower class services, and medium delay fairness for high class services.

  15. High disease activity is related to low levels of physical activity in patients with ankylosing spondylitis.

    Science.gov (United States)

    Fongen, Camilla; Halvorsen, Silje; Dagfinrud, Hanne

    2013-12-01

    This study aims to compare physical activity (PA) level and exercise habits in patients with ankylosing spondylitis (AS) who have high disease activity with those who have low disease activity and, further, to compare both groups with population controls. Cross-sectional study design was used. The participants include 149 patients (mean age 49.3 (SD 11.1), 61% men, 54% high disease activity) and 133 controls (mean age 52.7 (SD11.3), 58% men). PA was reported with the International PA Questionnaire-Long and results were presented as weekly energy expenditure (metabolic equivalent, MET) in different intensities, domains, and proportion reaching health enhancing physical activity (HEPA). Types of PA were registered in a structured interview. The AS Disease Activity Score was used to assess patients' disease activity. Patients with high disease activity reported significantly lower total weekly energy expenditure (MET) than patients with low disease activity and controls (p = 0.02, p = 0.01, respectively) and lower amounts of walking (p < 0.01, p = 0.02, respectively) and vigorous activity (p = 0.06, p = 0.06, respectively). Only 41% of the patients with high disease activity reached HEPA compared to 61% of the patients with low disease activity (p = 0.02). Patients in general participated less in leisure PA performed outdoor and with higher intensities (MET ≥ 6) than controls.AS patients with high disease activity had lower weekly energy expenditure in PA than patients with low disease activity and controls, and were less likely to reach HEPA than patients with low disease activity. For optimal management, health professionals should focus on physical activity in their consultations with AS patients, especially those with high disease activity.

  16. High Resolution Screening of biologically active compounds and metabolites

    NARCIS (Netherlands)

    Kool, J.

    2007-01-01

    High Resolution Screening of biologically active compounds and metabolites Jeroen Kool Biotransformation enzymes play a crucial role in the metabolism of both endogenous compounds and xenobiotics. Usually, the detoxication of these compounds by biotransformation enzymes results in harmless metab

  17. Broad-bandwidth and low-loss metamaterials:theory, design and realization

    Institute of Scientific and Technical Information of China (English)

    LI Le-wei; YAO Hai-ying; WU Qun; CHEN Zhi-ning

    2006-01-01

    In this paper, we summarize some recent activities in the field ofmetamaterial research at the National University of Singapore (NUS). Integral equations are applied for electromagnetic modelling of supernatural materials. Some special characteristics of the metamaterials are shown. Moreover, quasi-static Lorentz theory and numerical method (i.e., the method of moments for solving the electric field integral equation) and the transmission line theory are both presented to obtain the effective constitutive relations of metamaterials, respectively. Finally, feasibility of fabricating metamaterials based on analysis of equivalent transmission line model in the microwave spectrum and even higher is also shown and correspondingly some broad-bandwidth and low-loss metamaterial structures are designed and synthesized.

  18. MOVING TOWARD SYNCHRONOUS OPTICAL NETWORK STRATEGIES FOR EFFICIENT TELECOMMUNICATIONS TRANSPORT WITH INCREASED CONFIGURATION FLEXIBILITY AND BANDWIDTH AVAILABILITY

    Directory of Open Access Journals (Sweden)

    Dr.S.S.Riaz Ahamed

    2010-07-01

    Full Text Available Optical networks are high-capacity telecommunications networks based on optical technologies and components that provide routing, grooming, and restoration at the wavelength level as well as wavelength-based services. As networks face increasing bandwidth demand and diminishing fiber availability, network providers are moving towards a crucial milestone in network evolution: the optical network. Optical networks, based on the emergence of the optical layer in transport networks, provide higher capacity and reduced costs for new applications such as the Internet, video and multimedia interaction, and advanced digital services. Synchronous optical network (SONET is a standard for optical telecommunications transport. The increased configuration flexibility and bandwidth availability of SONET provides significant advantages over the older telecommunications system.

  19. Exploit the Bandwidth Capacities of the Perfluorinated Graded Index Polymer Optical Fiber for Multi-Services Distribution

    Directory of Open Access Journals (Sweden)

    Paul Alain Rolland

    2011-06-01

    Full Text Available The study reported here deals with the exploitation of perfluorinated graded index polymer optical fiber bandwidth to add further services in a home/office network. The fiber properties are exhibited in order to check if perfluorinated graded index plastic optical fiber (PFGI-POF is suitable to support a multiplexing transmission. According to the high bandwidth length of plastic fibers, both at 850 nm and 1,300 nm, the extension of the classical baseband existing network is proposed to achieve a dual concept, allowing the indoor coverage of wireless signals transmitted using the Radio over Fiber technology. The simultaneous transmission of a 10 GbE signal and a wireless signal is done respectively at 850 nm and 1,300 nm on a single plastic fiber using wavelength division multiplexing commercially available devices. The penalties have been evaluated both in digital (Bit Error Rate measurement and radiofrequency (Error Vector Magnitude measurement domains.

  20. A NEW DESIGN IMPROVEMENT OF MICROSTRIP U-SHAPE ANTENNA FOR BANDWIDTH ENHANCEMENT USING EBG STRUCTURE DEFORMATION

    Directory of Open Access Journals (Sweden)

    SUDHAKAR SRIVASTAVA

    2012-06-01

    Full Text Available The purpose of this paper is to design a low profile, conformal, small size antenna with high bandwidth along with good compromise in other factors like gain, directivity, efficiency etc. A U-shape patch antenna with suitable geometry is taken to provide good response of bandwidth about 30 % at centre frequency 2.025 GHz.using FR-4 glass epoxy material, on insertion of EBG structure, creating deformities at ground plane side, the band width of the antenna is improved tremendously about 49.36 % at centre frequency 2.35 GHz. The new design of antenna is found suitable for various wireless communications for S-band. The design approach & Simulation results are shown with the help of MOM based full wave simulator IE3D.

  1. Murine erythrocytes contain high levels of lysophospholipase activity

    NARCIS (Netherlands)

    Kamp, J.A.F. op den; Roelofsen, B.; Sanderink, G.; Middelkoop, E.; Hamer, R.

    1984-01-01

    Murine erythrocytes were found to be unique in the high levels of lysophospholipase activity in the cytosol of these cells. The specific activity of the enzyme in the cytosol of the murine cells is 10-times higher than in the cytosol of rabbit erythrocytes and approximately three orders of magnitude

  2. The physical activity climate in Minnesota middle and high schools.

    Science.gov (United States)

    Samuelson, Anne; Lytle, Leslie; Pasch, Keryn; Farbakhsh, Kian; Moe, Stacey; Sirard, John Ronald

    2010-11-01

    This article describes policies, practices, and facilities that form the physical activity climate in Minneapolis/St. Paul, Minnesota metro area middle and high schools and examines how the physical activity climate varies by school characteristics, including public/private, school location and grade level. Surveys examining school physical activity practices, policies and environment were administered to principals and physical education department heads from 115 middle and high schools participating in the Transdisciplinary Research on Energetics and Cancer-Identifying Determinants of Eating and Activity (TREC-IDEA) study. While some supportive practices were highly prevalent in the schools studied (such as prohibiting substitution of other classes for physical education); other practices were less common (such as providing opportunity for intramural (noncompetitive) sports). Public schools vs. private schools and schools with a larger school enrollment were more likely to have a school climate supportive of physical activity. Although schools reported elements of positive physical activity climates, discrepancies exist by school characteristics. Of note, public schools were more than twice as likely as private schools to have supportive physical activity environments. Establishing more consistent physical activity expectations and funding at the state and national level is necessary to increase regular school physical activity.

  3. 78 FR 70567 - Nationwide Use of High Frequency and Ultra High Frequency Active SONAR Technology; Final...

    Science.gov (United States)

    2013-11-26

    ...] Nationwide Use of High Frequency and Ultra High Frequency Active SONAR Technology; Final Programmatic... Programmatic Environmental Assessment (PEA) for the Nationwide Use of High Frequency (HF) and Ultra High Frequency (UHF) Sound Navigation and Ranging (SONAR) Technology and Finding of No Significant Impact (FONSI...

  4. Wide bandwidth nanowire electromechanics on insulating substrates at room temperature

    Science.gov (United States)

    Sebastian, Abhilash; Mathew, John; Sengupta, Shamashis; Gokhale, Maheshwar; Bhattacharya, Arnab; Deshmukh, Mandar

    2013-03-01

    We present a simple fabrication scheme for nano-scale devices on insulating substrates. Doubly clamped InAs nanowire resonators with local gate configuration are fabricated on sapphire substrates. Parasitic capacitance is reduced on insulating substrates thus enabling measurements at all temperatures and particularly above room temperature, an essential requirement for NEMS sensors. Mechanical motion of the nanowire is capacitively actuated and detected using a network analyser. This technique provides wide bandwidth radio frequency transduction and allows the nanowire oscillations to be probed at a much faster rate compared to mixing techniques. Both in-plane and out-of-plane vibrational modes of the nanowire are observed and the non-linear response of the resonators is studied. Quality factor of the resonator increases at low temperatures. We also study the relation between mechanical motion and thermal strains in the nanowire. This opens up a new approach in studying thermal properties of nanostructures. Our method of fabrication can be extended to NEMS devices on flexible substrates and other nanostructures.

  5. Extraction of spatial information for low-bandwidth telerehabilitation applications

    Directory of Open Access Journals (Sweden)

    Kok Kiong Tan, PhD

    2014-09-01

    Full Text Available Telemedicine applications, based on two-dimensional (2D video conferencing technology, have been around for the past 15 to 20 yr. They have been demonstrated to be acceptable for face-to-face consultations and useful for visual examination of wounds and abrasions. However, certain telerehabilitation assessments need the use of spatial information in order to accurately assess the patient’s condition and sending three-dimensional video data over low-bandwidth networks is extremely challenging. This article proposes an innovative way of extracting the key spatial information from the patient’s movement during telerehabilitation assessment based on 2D video and then presenting the extracted data by using graph plots alongside the video to help physicians in assessments with minimum burden on existing video data transfer. Some common rehabilitation scenarios are chosen for illustrations, and experiments are conducted based on skeletal tracking and color detection algorithms using the Microsoft Kinect sensor. Extracted data are analyzed in detail and their usability discussed.

  6. Octave Bandwidth Orthomode Transducers for the Expanded Very Large Array

    Science.gov (United States)

    Coutts, Gordon M.

    2011-06-01

    Quadruple-ridge orthomode transducers (OMTs) have been designed to operate over a full octave bandwidth for the expanded very large array (EVLA) project. The OMT separates linearly polarized signal components by matching a circular waveguide input to two orthogonal coaxial outputs. The OMT is used in conjunction with a quadrature hybrid to detect circularly polarized signal components. This paper focuses on the 1 GHz-2 GHz L-Band OMT design, which has better than 18.8 dB measured return loss across the band, with no evidence of trapped-mode resonances. The OMT is designed with an emphasis on performance, ease of tuning and manufacturability since a large number of units are needed for the array application. Extensive parametric analyses were carried out, and nominal dimensions have been set to ensure the devices exceed RF specifications provided the parts are machined to within specified tolerances. With excellent wideband performance and a simplified manufacturing process, the proposed OMT would be amenable to much larger future array projects.

  7. QoS routing via multiple paths using bandwidth reservation

    Energy Technology Data Exchange (ETDEWEB)

    Rao, N.S.V.; Batsell, S.G.

    1998-01-01

    The authors address the problem of computing a multipath, consisting of possibly overlapping paths, to transmit data from the source node s to the destination node d over a computer network while ensuring deterministic bounds on end-to-end delay or delivery rate.They consider two generic routing problems within the framework wherein bandwidth can be reserved, and guaranteed, once reserved, on various links of the communication network. The first problem requires that a message of finite length be transmitted from s to d within {tau} units of time. The second problem requires that a sequential message of r units be transmitted at a rate of {eta} such that maximum time difference between two units that are received out of order is no more than q. They propose a polynomial-time algorithm to the first problem based on an adaptation of the classical Ford-Fulkerson`s method. They present simulation results to illustrate the applicability of the proposed algorithm. They show the second problem to be NP-complete, and propose a polynomial-time approximately solution.

  8. QoS routing via multiple paths using bandwidth reservation

    Energy Technology Data Exchange (ETDEWEB)

    Rao, N.S.V.; Batsell, S.G.

    1997-11-01

    The authors address the problem of computing a multipath, consisting of possibly overlapping paths, to transmit data from the source node s to the destination node d over a computer network while ensuring deterministic bounds on end-to-end delay or delivery rate. They consider two generic routing problems within the framework wherein bandwidth can be reserved, and guaranteed, once reserved, on various links of the communication network. The first problem requires that a message of finite length be transmitted from s to d within {tau} units of time. The second problem requires that a sequential message of r units be transmitted at a rate of {eta} such that maximum time difference between two units that are received out of order is no more than q. They propose a polynomial-time algorithm to the first problem based on an adaptation of the classical Ford-Fulkerson`s method. They present simulation results to illustrate the applicability of the proposed algorithm. They show the second problem to be NP-complete and propose a polynomial-time approximate solution.

  9. Experimental conditions affecting functional comparison of highly active glutathione transferases.

    Science.gov (United States)

    Fedulova, Natalia; Mannervik, Bengt

    2011-06-01

    Glutathione transferases (GSTs, EC 2.5.1.18) possess multiple functions and have potential applications in biotechnology. Direct evidence of underestimation of activity of human GST A3-3 and porcine GST A2-2 measured at submicromolar enzyme concentrations is reported here for the first time. The combination of time-dependent and enzyme concentration-dependent loss of activity and the choice of the organic solvent for substrates were found to cause irreproducibility of activity measurements of GSTs. These effects contribute to high variability of activity values of porcine GST A2-2 and human Alpha-class GSTs reported in the literature. Adsorption of GSTs to surfaces was found to be the main explanation of the observed phenomena. Several approaches to improved functional comparison of highly active GSTs are proposed.

  10. The TSU Streaming Video Astronomy Course - II, Video Interface Design and Bandwidth Considerations

    Science.gov (United States)

    Burks, G. S.; Smith, W.

    2004-12-01

    Researchers are developing an on-line video astronomy course at Tennessee State University. Many factors are taken into account when designing a first year course for a broad audience. The initial target audience is students attending historically black colleges and universities, tribal colleges, and other minority institutions, without an astronomy course. The primary goal is to attract students into a course of study that could prepare them to enter the NASA workforce. A secondary goal is to serve the general student population. The question we try to address here is: How can we deliver the video components of such a course in a way that will take into account the innate learning styles of most students and the limited access to very high speed internet lines in smaller colleges? The design for the video information interface will be discussed. The effect of limited bandwidth on video size and other features of the presentation design is also analyzed.

  11. Performance of the CMS Tracker Optical Links and Future Upgrade Using Bandwidth Efficient Digital Modulation

    CERN Document Server

    Dris, Stefanos; Troska, J

    2006-01-01

    The Compact Muon Solenoid (CMS) experiment at the Large Hadron Collider (LHC) particle accelerator will begin operation in 2007. The innermost CMS subdetector, the Tracker, comprises ~10 million detector channels read out by ~40 000 analog optical links. The optoelectronic components have been designed to meet the stringent requirements of a high energy physics (HEP) experiment in terms of radiation hardness, low mass and low power. Extensive testing has been performed on the components and on complete optical links in test systems. Their functionality and performance in terms of gain, noise, linearity, bandwidth and radiation hardness is detailed. Particular emphasis is placed on the gain, which directly affects the dynamic range of the detector data. It has been possible to accurately predict the variation in gain that will be observed throughout the system. A simulation based on production test data showed that the average gain would be ~38% higher than the design target at the Tracker operating temperatur...

  12. Note: A simple broad bandwidth undersampling frequency-domain digital diffuse optical spectroscopy system

    Science.gov (United States)

    Jung, Justin; Istfan, Raeef; Roblyer, Darren

    2014-07-01

    Near-Infrared frequency-domain technologies, such as Diffuse Optical Spectroscopy (DOS), have demonstrated growing potential in a number of clinical applications. The broader dissemination of this technology is limited by the complexity and cost of instrumentation. We present here a simple system constructed with off-the-shelf components that utilizes undersampling for digital frequency-domain dDOS measurements. Broadband RF sweeps (50-300 MHz) were digitally sampled at 25 MSPS; amplitude, phase, and optical property extractions were within 5% of network analyzer derived values. The use of undersampling for broad bandwidth dDOS provides a significant reduction in complexity, power consumption, and cost compared with high-speed ADCs and analog techniques.

  13. Battery-Bandwidth Based Handover Framework for 3G/WLAN Using Android Handheld Devices

    Directory of Open Access Journals (Sweden)

    Apoorva Prakash M V

    2014-06-01

    Full Text Available In a heterogeneous network environment, transparent horizontal and vertical handover is a much desired feature. Effective handover solution would allow mobile device users to stay steadily connected, seamlessly switching between different access networks. If it is consistently connected to networks which offers best Quality of Service (QoS then that would dramatically improve user experience. Switching of network requires more device energy and also high bandwidth to guarantee the QoS. Automatic handover between 3G and WLAN networks is typically done when the current network link is going down. Current devices does not consider these two major metrics during handover. Hence, we propose a framework for creating our own custom handover solutions which could run on the clients’ Android based mobile devices. To provide an example of using the framework, we implement and test our proposed framework in Android based hand held devices and showcase the improvement in QoS.

  14. An adaptive mechanism to guarantee the bandwidth fairness of TCP flows

    Institute of Scientific and Technical Information of China (English)

    张顺亮; 叶澄清

    2004-01-01

    End-to-end TCP (transmission control protocol) congestion control can cause unfairness among multiple TCP connections with different RTT (Round Trip Time). The throughput of TCP connection is inversely proportional to its RTT. To resolve this problem, researchers have proposed many methods. The existing proposals for RTT-aware conditioner work well when congestion level is low. However, they over-protect long RTT flows and starve short RTT flows when congestion level is high. Due to this reason, an improved method based on adaptive thought is proposed. According to the congestion level of networks, the mechanism can adaptively adjust the degree of the protection to long RTT flows. Extensive simulation experiments showed that the proposed mechanism can guarantee the bandwidth fairness of TCP flows effectively and outperforms the existing methods.

  15. Solid-core fiber with ultra-wide bandwidth transmission window due to inhibited coupling.

    Science.gov (United States)

    Grujic, Thomas; Kuhlmey, Boris T; Argyros, Alexander; Coen, Stéphane; de Sterke, C Martijn

    2010-12-01

    We experimentally demonstrate solid-core photonic crystal fibers that guide via the inhibited coupling mechanism. We measure an overall transmission window of more than an octave, as well as an uninterrupted width of almost one octave. The fiber is fabricated in polymer, with high-index ring-shaped inclusions. This type of fiber was conceived based on a simple model which shows that the cutoffs of the modes of a thin ring cluster around the cutoffs of planar waveguide modes. The model shows that such ring based fibers are closely related to kagome and square lattice hollow core fibers, and have transmission bandwidths that could in principle reach 1.6 octaves. Measured transmission properties are in good agreement with rigorous modelling.

  16. Demonstration of a Tunable-Bandwidth White Light Interferometer using Anomalous Dispersion in Atomic Vapor

    CERN Document Server

    Pati, G S; Salit, M; Shahriar, M S

    2006-01-01

    The concept of the 'white-light cavity' has recently generated considerable research interest in the context of gravitational wave detection. Cavity designs are proposed using negative (or anomalous) dispersion in an intracavity medium to make the cavity resonate over a large range of frequencies and still maintain a high cavity build-up. This paper presents the first experimental attempt and demonstration of white-light effect in a meter long ring cavity using an intracavity atomic medium. The medium's negative dispersion is caused by bi-frequency Raman gain in an atomic vapor cell. Although the white light condition was not perfectly achieved and improvements in experimental control are still desirable, significantly broad cavity response over bandwidth greater than 20 MHz has been observed. These devices will have potential applications in new generation laser interferometer gravitational wave detectors.

  17. An adaptive mechanism to guarantee the bandwidth fairness of TCP flows

    Institute of Scientific and Technical Information of China (English)

    张顺亮; 叶澄清

    2004-01-01

    End-to-end TCP(transmission control protocol)congestion control can cause unfairness among multiple TCP connections with different RTT(Round Trip Time). The throughput of TCP connection is inversely proportional to its RTT.To resolve this problem,researchers have proposed many methods. The existing proposals for RTT-aware conditioner work well when congestion level is low. However,they over-protect long RTT flows and starve short RTT flows when congestion level is high. Due to this reason,an improved method based on adaptive thought is proposed. According to the congestion level of networks,the mechanism can adaptively adjust the degree of the protection to long RTT flows. Extensive simulation experiments showed that the proposed mechanism can guarantee the bandwidth fairness of TCP flows effectively and outperforms the existing methods.

  18. Self-organized Balanced Resources in Random Networks with Transportation Bandwidths

    Science.gov (United States)

    Yeung, Chi Ho; Wong, K. Y. Michael

    We apply statistical physics to study the task of resource allocation in random networks with limited bandwidths for the transportation of resources along the links. We derive algorithms which searches the optimal solution without the need of a global optimizer. For networks with uniformly high connectivity, the resource shortage of a node becomes a well-defined function of its capacity. An efficient profile of the allocated resources is found, with clusters of node interconnected by an extensive fraction of unsaturated links, enabling the resource shortages among the nodes to remain balanced. The capacity-shortage relation exhibits features similar to the Maxwell’s construction. For scale-free networks, such an efficient profile is observed even for nodes of low connectivity.

  19. High Power VCSEL Device with Periodic Gain Active Region

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    High power vertical cavity surface emitting lasers(VCSEKLs) with large aperture have been fabricated through improving passivation, lateral oxidation and heat dissipation techniques. Different from conventional three quantum well structures, a periodic gain active region with nine quantum wells was incorporated into the VCSEL structure, with which high efficiency and high power operation were expected. The nine quantum wells were divided into three groups with each of them located at the antinodes of the ca...

  20. Effects of Signal Spectrum Bandwidth on Different PMD Compensation Feedback Methods

    Institute of Scientific and Technical Information of China (English)

    Na Young Kim; Duckey Lee; Sangin Kim; Namkyoo Park

    2003-01-01

    We compared efficiencies of different PMD compensation feedback methods against transmission signal bandwidth,including NRZ, RZ, CRZ format under various duty cycles. We found that the critical factor determining the efficiency of PMD compensation is not the modulation format, but the spectral bandwidth of the transmission signal.

  1. Effects of Signal Spectrum Bandwidth on Different PMD Compensation Feedback Methods

    Institute of Scientific and Technical Information of China (English)

    Na; Young; Kim; Duckey; Lee; Sangin; Kim; Namkyoo; Park

    2003-01-01

    We compared efficiencies of different PMD compensation feedback methods against transmission signal bandwidth, including NRZ, RZ, CRZ format under various duty cycles. We found that the critical factor determining the efficiency of PMD compensation is not the modulation format, but the spectral bandwidth of the transmission signal.

  2. A hybrid OFDM-TDM architecture with decentralized dynamic bandwidth allocation for PONs.

    Science.gov (United States)

    Cevik, Taner

    2013-01-01

    One of the major challenges of passive optical networks is to achieve a fair arbitration mechanism that will prevent possible collisions from occurring at the upstream channel when multiple users attempt to access the common fiber at the same time. Therefore, in this study we mainly focus on fair bandwidth allocation among users, and present a hybrid Orthogonal Frequency Division Multiplexed/Time Division Multiplexed architecture with a dynamic bandwidth allocation scheme that provides satisfying service qualities to the users depending on their varying bandwidth requirements. Unnecessary delays in centralized schemes occurring during bandwidth assignment stage are eliminated by utilizing a decentralized approach. Instead of sending bandwidth demands to the optical line terminal (OLT) which is the only competent authority, each optical network unit (ONU) runs the same bandwidth demand determination algorithm. ONUs inform each other via signaling channel about the status of their queues. This information is fed to the bandwidth determination algorithm which is run by each ONU in a distributed manner. Furthermore, Light Load Penalty, which is a phenomenon in optical communications, is mitigated by limiting the amount of bandwidth that an ONU can demand.

  3. 图的循环带宽和%CYCLIC BANDWIDTH SUM OF GRAPHS

    Institute of Scientific and Technical Information of China (English)

    郝建修

    2001-01-01

    Let G be a simple graph. The cyclic bandwidth sum problem is to determine a labeling of graph G in a cycle such that the total length of edges is as small as possible. In this paper, some upper and lower bounds on cyclic bandwidth sum of graphs are studied.

  4. Bandwidth Management in Universities in Zimbabwe: Towards a Responsible User Base through Effective Policy Implementation

    Science.gov (United States)

    Chitanana, Lockias

    2012-01-01

    This research was undertaken to investigate the issue of how to maximise or make efficient use of bandwidth. In particular, the research sought to find out about what universities in Zimbabwe are doing to manage their bandwidth. It was, therefore, appropriate to survey a sample of five universities and to catalogue their experiences. Results show…

  5. Bandwidth limitations in current mode and voltage mode integrated feedback amplifiers

    DEFF Research Database (Denmark)

    Bruun, Erik

    1995-01-01

    loop bandwidth remains constant for a feedback amplifier. The constant-bandwidth relations of such amplifier designs are reviewed in this paper and they are combined with the constraints imposed by technology when the feedback amplifier is to be designed in an integrated technology. From this analysis...

  6. Agent based Bandwidth Reservation Routing Technique in Mobile Ad Hoc Networks

    Directory of Open Access Journals (Sweden)

    Vishnu Kumar Sharma,

    2011-12-01

    Full Text Available In mobile ad hoc networks (MANETs, inefficient resource allocation causes heavy losses to the service providers and results in inadequate user proficiency. For improving and automating the quality of service of MANETs, efficient resource allocation techniques are required. In this paper, we propose an agent based bandwidth reservation technique for MANET. The mobile agent from the source starts forwarding the data packets through the path which has minimum cost, congestion and bandwidth. The status of every node is collected which includes the bottleneck bandwidth field and the intermediate node computes the available bandwidth on the link. At the destination, after updating the new bottleneck bandwidth field, the data packet is feedback to the source. In resource reservation technique, if the available bandwidth is greater than bottleneck bandwidth, then bandwidth reservation for the flow is done. Using rate monitoring and adjustment methodologies, rate control is performed for the congested flows. By simulation results, we show that the resource allocation technique reduces the losses and improves the network performance.

  7. A Hybrid OFDM-TDM Architecture with Decentralized Dynamic Bandwidth Allocation for PONs

    Science.gov (United States)

    Cevik, Taner

    2013-01-01

    One of the major challenges of passive optical networks is to achieve a fair arbitration mechanism that will prevent possible collisions from occurring at the upstream channel when multiple users attempt to access the common fiber at the same time. Therefore, in this study we mainly focus on fair bandwidth allocation among users, and present a hybrid Orthogonal Frequency Division Multiplexed/Time Division Multiplexed architecture with a dynamic bandwidth allocation scheme that provides satisfying service qualities to the users depending on their varying bandwidth requirements. Unnecessary delays in centralized schemes occurring during bandwidth assignment stage are eliminated by utilizing a decentralized approach. Instead of sending bandwidth demands to the optical line terminal (OLT) which is the only competent authority, each optical network unit (ONU) runs the same bandwidth demand determination algorithm. ONUs inform each other via signaling channel about the status of their queues. This information is fed to the bandwidth determination algorithm which is run by each ONU in a distributed manner. Furthermore, Light Load Penalty, which is a phenomenon in optical communications, is mitigated by limiting the amount of bandwidth that an ONU can demand. PMID:24194684

  8. Dynamic Wavelength and Bandwidth Allocation Using Adaptive Linear Prediction in WDM/TDM Ethernet Passive Optical Networks

    Institute of Scientific and Technical Information of China (English)

    LU Yi-yi; GUO Yong; HE Chen

    2009-01-01

    Hybrid wavelength-division-multiplexing (WDM)/time-division-multiplexing (TDM) ethernet passive optical networks (EPONs) can achieve low per-subscriber cost and scalability to increase the number of subscribers. This paper discusses dynamic wavelength and bandwidth allocation (DWBA) algorithm in hybrid WDM/TDM EPONs. Based on the correlation structure of the variable bit rate (VBR) video traffic, we propose a quality-of-service (QoS) supported DWBA using adaptive linear traffic prediction. Wavelength and timeslot are allocated dynamically by optical line terminal (OLT) to all optical network units (ONUs) based on the bandwidth requests and the guaranteed service level agreements (SLA) of all ONUs. Mean square error of the predicted average arriv-ing rate of compound video traffic during waiting period is minimized through Wiener-Hopf equation. Simulation results show that the DWBA-adaptive-linear-prediction (DWBA-ALP) algorithm can significantly improve the QoS performances in terms of low delay and high bandwidth utilization.

  9. Impact of bandwidth for various services in heterogeneous network and quality of service via communication technologies in Malaysian higher educational

    Directory of Open Access Journals (Sweden)

    Mohd Nazri ISMAIL

    2007-12-01

    Full Text Available This study focuses on heterogeneous services and communication technologies for retrieving and sending information between students and lecturers in Malaysian higher educational institutes. It intends to investigate pattern and significant level of various services implementation, convergence of communication technologies and bandwidth capacity for last mile users (students and lecturers. It is designed to determine which communication technologies, services, bandwidth capacity and QoS will achieve the highest level acceptance in Malaysian higher educational institutes. Heterogeneous environment can also generate mobility approaches. A survey method is used to collect data from respondents (System Network Administrator in Malaysian higher educational institutes. Statistical Analysis using t-test shows that implementation of high speed bandwidth for Internet (WAN achieved significant level. Frequency test are used to analyze the various services implementation via convergence of communication technologies in heterogeneous environment for retrieving information. The most apparent finding of this study is that various services implementation in higher educational institutes can affect convergence of communication technologies usage in accessing information over heterogeneous network environment between students and lecturers. The study or analysis confirms that Malaysia higher educational institutes have not achieved a maximum level of various services implementation via convergence of communication technologies between students and lecturers in heterogeneous network environment. Therefore, low convergence of communication technologies can produce a low mobility and ubiquitous interaction between students and lectures in Malaysian higher educational institutes.

  10. Miniaturization and Bandwidth Enhancement of a Microstrip Patch Antenna Using Magneto-Dielectric Materials for Proximity Fuze Application

    Science.gov (United States)

    Saini, Ashish; Thakur, Atul; Thakur, Preeti

    2017-03-01

    The exact calculation of height of burst has always been a challenge in the design of proximity fuzes. Radio frequency-based sensors can be designed for this purpose but the size and bandwidth of the antenna increases the design complexity; hence, miniaturization of the patch antenna using barium hexaferrite (BaFe12O19) as substrate material is proposed in this paper. The nanohexaferrite substrate material was prepared using a wet chemical method and characterized for structural and electromagnetic properties. An average crystallite size of 60 nm was obtained from x-ray diffraction. Scanning electron microscopy and transmission electron microscopy also confirms the formation of homogenous nanoferrites. Complex permittivity ( ɛ * = 6.2 - 0.04 j) and complex permeability ( μ * = 1.9 - 0.18 j) were obtained from electromagnetic characterization. The antenna structure fabricated and simulated confirms that, with the obtained electromagnetic parameters of synthesized magneto-dielectric material, the size of antenna can be reduced up to 42.5%. It also increases the bandwidth from 68 MHz to 166 MHz with respect to antenna on FR4 substrate. Therefore, BaFe12O19 is proposed as a suitable candidate for a high-bandwidth, miniaturized antenna for proximity fuzes.

  11. Super-SERS-active and highly effective antimicrobial Ag nanodendrites

    Science.gov (United States)

    Li, H. B.; Liu, P.; Liang, Y.; Xiao, J.; Yang, G. W.

    2012-07-01

    We have developed simple and green electrochemistry to synthesize Ag nanostructures with high purity, good crystallinity and smooth surface for applications as super-SERS (surface-enhanced Raman scattering), SERS-active substrates and with highly effective antimicrobial activities. This synthesis takes place in a clean and slow reaction environment without any chemical additives, which ensures an ultrahigh active surface of the as-synthesized Ag nanostructures owing to their purity, good crystallinity and smooth morphology. Using this method, we synthesized nearly perfect Ag nanodendrites (NDs), which exhibit super-SERS sensitivity when they are used to detect the SERS spectra of rhodamine 6G at concentrations as low as 5 × 10-16 M, and have an ultrahigh electromagnetic (EM) enhancement factor of the order of 1013, breaking through the theoretical limit of EM enhancement. Meanwhile, the as-synthesized Ag NDs possess highly effective antimicrobial activities for Escherichia coli, Candida albicans and Staphylococcus aureus, which are over 10 times that of silver nanoparticles. Additionally, the basic physics and chemistry involved in the fabrication of Ag nanostructures are pursued. These investigations show that silver nanostructures with highly active surfaces can make the most of Ag nanostructures functioning as super-SERS-active substrates and multiple antibiotics.

  12. Dynamic Bandwidth Allocation Technique in ATM Networks Based on Fuzzy Neural Networks and Genetic Algorithm

    Institute of Scientific and Technical Information of China (English)

    ZhangLiangjie; LiYanda; 等

    1997-01-01

    In this paper,a dynamic bandwidth allocation technique based on fuzz neural networks(FNNs) and genetic algorithm(GA)is proposed for preventive congestion control in ATM network.The traffic model based on FNN does not need the descriptive traffic parameters in detail,which greatly depend on the user's terminal.Genetic algorithm is used to predict the equivalent bandwidth of the accepted traffic in real-time.Thus,the proposed scheme can estimate the dynamic bandwidth of the network in the time scale from the call arrival to the call admission/rejection due to the fuzzy-tech and GA hardware implementation.Simulation results show that the scheme can perform accurate dynamic bandwidth allocation to DN/OFF bursty traffic in accordance with the required quality of service(QOS),and the bandwidth utilization is improved from the overall point of view.

  13. School day segmented physical activity patterns of high and low active children

    Science.gov (United States)

    2012-01-01

    Background Variability exists in children’s activity patterns due to the association with environmental, social, demographic, and inter-individual factors. This study described accelerometer assessed physical activity patterns of high and low active children during segmented school week days whilst controlling for potential correlates. Methods Two hundred and twenty-three children (mean age: 10.7 ± 0.3 yrs, 55.6% girls, 18.9% overweight/obese) from 8 north-west England primary schools wore ActiGraph GT1M accelerometers for 7 consecutive days during autumn of 2009. ActiGraph counts were converted to minutes of moderate (MPA), vigorous (VPA) and moderate-to-vigorous (MVPA) physical activity. Children were classified as high active (HIGH) or low active (LOW) depending on the percentage of week days they accumulated at least 60 minutes of MVPA. Minutes spent in MPA and VPA were calculated for school time and non-school time and for five discrete school day segments (before-school, class time, recess, lunchtime, and after-school). Data were analysed using multi-level modelling. Results The HIGH group spent significantly longer in MPA and/or VPA before-school, during class time, lunchtime, and after-school (P children, playground area per student, and temperature, depending on the segment analysed. The additive effect of the segment differences was that the HIGH group accumulated 12.5 minutes per day more MVPA than the LOW group. Conclusions HIGH active children achieved significantly more MPA and VPA than LOW active during four of the five segments of the school day when analyses were adjusted for potential correlates. Physical activity promotion strategies targeting low active children during discretionary physical activity segments of the day, and particularly via structured afterschool physical activity programs may be beneficial. PMID:22672654

  14. School day segmented physical activity patterns of high and low active children.

    Science.gov (United States)

    Fairclough, Stuart J; Beighle, Aaron; Erwin, Heather; Ridgers, Nicola D

    2012-06-06

    Variability exists in children's activity patterns due to the association with environmental, social, demographic, and inter-individual factors. This study described accelerometer assessed physical activity patterns of high and low active children during segmented school week days whilst controlling for potential correlates. Two hundred and twenty-three children (mean age: 10.7 ± 0.3 yrs, 55.6% girls, 18.9% overweight/obese) from 8 north-west England primary schools wore ActiGraph GT1M accelerometers for 7 consecutive days during autumn of 2009. ActiGraph counts were converted to minutes of moderate (MPA), vigorous (VPA) and moderate-to-vigorous (MVPA) physical activity. Children were classified as high active (HIGH) or low active (LOW) depending on the percentage of week days they accumulated at least 60 minutes of MVPA. Minutes spent in MPA and VPA were calculated for school time and non-school time and for five discrete school day segments (before-school, class time, recess, lunchtime, and after-school). Data were analysed using multi-level modelling. The HIGH group spent significantly longer in MPA and/or VPA before-school, during class time, lunchtime, and after-school (P children, playground area per student, and temperature, depending on the segment analysed.The additive effect of the segment differences was that the HIGH group accumulated 12.5 minutes per day more MVPA than the LOW group. HIGH active children achieved significantly more MPA and VPA than LOW active during four of the five segments of the school day when analyses were adjusted for potential correlates. Physical activity promotion strategies targeting low active children during discretionary physical activity segments of the day, and particularly via structured afterschool physical activity programs may be beneficial.

  15. School day segmented physical activity patterns of high and low active children

    Directory of Open Access Journals (Sweden)

    Fairclough Stuart J

    2012-06-01

    Full Text Available Abstract Background Variability exists in children’s activity patterns due to the association with environmental, social, demographic, and inter-individual factors. This study described accelerometer assessed physical activity patterns of high and low active children during segmented school week days whilst controlling for potential correlates. Methods Two hundred and twenty-three children (mean age: 10.7 ± 0.3 yrs, 55.6% girls, 18.9% overweight/obese from 8 north-west England primary schools wore ActiGraph GT1M accelerometers for 7 consecutive days during autumn of 2009. ActiGraph counts were converted to minutes of moderate (MPA, vigorous (VPA and moderate-to-vigorous (MVPA physical activity. Children were classified as high active (HIGH or low active (LOW depending on the percentage of week days they accumulated at least 60 minutes of MVPA. Minutes spent in MPA and VPA were calculated for school time and non-school time and for five discrete school day segments (before-school, class time, recess, lunchtime, and after-school. Data were analysed using multi-level modelling. Results The HIGH group spent significantly longer in MPA and/or VPA before-school, during class time, lunchtime, and after-school (P P  The additive effect of the segment differences was that the HIGH group accumulated 12.5 minutes per day more MVPA than the LOW group. Conclusions HIGH active children achieved significantly more MPA and VPA than LOW active during four of the five segments of the school day when analyses were adjusted for potential correlates. Physical activity promotion strategies targeting low active children during discretionary physical activity segments of the day, and particularly via structured afterschool physical activity programs may be beneficial.

  16. Bandwidth Resource Dynamic Allocation in Differentiated Services Model%Diffserv中带宽代理BB的实现

    Institute of Scientific and Technical Information of China (English)

    邱瑜; 朱淼良

    2003-01-01

    To employ Differentiated Services, efficient and flexible resource allocation mechanism is needed. Static bandwidth resource allocation Is not suitable for the situations in which traffic varies greatly with times. If customers bought bandwidth according to their highest traffic demands, some resource will be wasted when traffic load is light. On the other hand, the static allocated bandwidth may not satisfy the growing traffic demands. So it is necessary to allocate bandwidth resource in dynamic way. We bring up a prototype of BB, discussing the necessary components to realize the dynamic bandwidth resource allocation and further more, our BB can provides advanced reservation for bandwidth resource. Simulation tests show our design is feasible.

  17. Recommendations of activity restriction in high-risk pregnancy scenarios

    DEFF Research Database (Denmark)

    Bendix, Jane; Hegaard, Hanne Kristine; Bergholt, Thomas;

    2015-01-01

    obstetricians and midwives prescribe activity restriction in most high-risk pregnancies. The degree of activity restriction and the presumed effect vary between clinicians. This may reflect different attitudes and lack of guidelines based on clinical studies of a possible benefit of activity restriction....... to the obstetricians, the midwives also reported that they expected the recommendation to be more effective. Most midwives and obstetricians reported that they thought strict activity restriction was associated with severe or moderate adverse effect, and recommended antithrombotic prophylaxis. Conclusions: Danish......Abstract Aims: To describe specific recommendations of activity restriction, place of care, expected beneficial and adverse effects, and recommended antithrombotic prophylaxis in nine clinical scenarios. Methods: A national survey. All members of the Danish Society of Obstetrics and Gynaecology...

  18. High lightning activity in maritime clouds near Mexico

    Directory of Open Access Journals (Sweden)

    B. Kucienska

    2012-01-01

    Full Text Available Lightning activity detected by the World Wide Lightning Location Network (WWLLN over oceanic regions adjacent to Mexico is often as high as that observed over the continent. In order to explore the possible cause of the observed high flash density over those regions, the relationships between lightning, rainfall, vertical hydrometeor profiles, latent heating, wind variability and aerosol optical thickness are analyzed. The characteristics of lightning and precipitation over four oceanic zones adjacent to Mexican coastlines are contrasted against those over the continent. In addition, we compare two smaller regions over the Tropical Pacific Ocean: one located within the Inter-Tropical Converge Zone and characterized by high rainfall and weak lightning activity and the other influenced by a continental jet and presenting high rainfall and strong lightning activity over the Gulf of Tehuantepec. Maritime precipitating clouds that develop within the region influenced by offshore winds exhibit similar properties to continental clouds: large content of precipitation ice and an increased height range of coexistence of precipitation ice and cloud water. During the rainy season, monthly distribution of lightning within the region influenced by the continental jet is contrary to that of rainfall. Moreover, the monthly variability of lightning is very similar to the variability of the meridional wind component and it is also related to the variability of aerosol optical depth. The analysis strongly suggests that the high lightning activity observed over the Gulf of Tehuantepec is caused by continental cloud condensation nuclei advected over the ocean.

  19. Coarse-Grain Bandwidth Estimation Scheme for Large-Scale Network

    Science.gov (United States)

    Cheung, Kar-Ming; Jennings, Esther H.; Sergui, John S.

    2013-01-01

    A large-scale network that supports a large number of users can have an aggregate data rate of hundreds of Mbps at any time. High-fidelity simulation of a large-scale network might be too complicated and memory-intensive for typical commercial-off-the-shelf (COTS) tools. Unlike a large commercial wide-area-network (WAN) that shares diverse network resources among diverse users and has a complex topology that requires routing mechanism and flow control, the ground communication links of a space network operate under the assumption of a guaranteed dedicated bandwidth allocation between specific sparse endpoints in a star-like topology. This work solved the network design problem of estimating the bandwidths of a ground network architecture option that offer different service classes to meet the latency requirements of different user data types. In this work, a top-down analysis and simulation approach was created to size the bandwidths of a store-and-forward network for a given network topology, a mission traffic scenario, and a set of data types with different latency requirements. These techniques were used to estimate the WAN bandwidths of the ground links for different architecture options of the proposed Integrated Space Communication and Navigation (SCaN) Network. A new analytical approach, called the "leveling scheme," was developed to model the store-and-forward mechanism of the network data flow. The term "leveling" refers to the spreading of data across a longer time horizon without violating the corresponding latency requirement of the data type. Two versions of the leveling scheme were developed: 1. A straightforward version that simply spreads the data of each data type across the time horizon and doesn't take into account the interactions among data types within a pass, or between data types across overlapping passes at a network node, and is inherently sub-optimal. 2. Two-state Markov leveling scheme that takes into account the second order behavior of

  20. Evanescent field interaction of tapered fiber with graphene oxide in generation of wide-bandwidth mode-locked pulses

    Science.gov (United States)

    Ahmad, H.; Faruki, M. J.; Razak, M. Z. A.; Tiu, Z. C.; Ismail, M. F.

    2017-02-01

    Pulses with picosecond pulse widths are highly desired for high precision laser applications. A mode-locked pulse laser utilizing evanescent field interaction of a tapered fiber with graphene oxide (GO) is demonstrated. A homemade fabrication stage was used to fabricate the tapered fiber using systematic flame brushing and a GO solution was used to coat the microfiber using optical deposition technique. Pulse trains with a pulse width of 3.46 ps, a 3 dB optical bandwidth of 11.82 nm and a repetition rate of 920 kHz were obtained. The system has substantial potential for many crucial medical, communication, bio processing, military, and industrial applications.