Structural characterization of asphaltenes from vacuum residue distillation

International Nuclear Information System (INIS)

Silva, Ronaldo C.; Seidl, Peter R.; Menezes, Sonia M.C. de; Teixeira, Marco A.G.

2001-01-01

The aim of this work was to do structural characterization of asphaltenes from different vacuum residues distillation. Several average molecular parameters using some analytical techniques were obtained and these techniques were: nuclear magnetic resonance ( 1 H and 13 C NMR), elemental analysis (C,H,N,O and S content), Fourier transform infrared (FT-IR), vapor pressure osmometry and gel permeation chromatography. Particularly from NMR, some important molecular parameters were obtained, such as aromatic carbon fraction, aliphatic carbons fraction, alkyl substituted aromatic carbons, unsubstituted aromatic carbons, etc. Molecular modeling will be employed to build the structure of asphaltenes using the experimental data. (author)

Enhanced Oil Recovery (EOR by Miscible CO2 and Water Flooding of Asphaltenic and Non-Asphaltenic Oils

Directory of Open Access Journals (Sweden)

Edwin A. Chukwudeme

2009-09-01

Full Text Available An EOR study has been performed applying miscible CO2 flooding and compared with that for water flooding. Three different oils are used, reference oil (n-decane, model oil (n-C10, SA, toluene and 0.35 wt % asphaltene and crude oil (10 wt % asphaltene obtained from the Middle East. Stearic acid (SA is added representing a natural surfactant in oil. For the non-asphaltenic oil, miscible CO2 flooding is shown to be more favourable than that by water. However, it is interesting to see that for first years after the start of the injection (< 3 years it is shown that there is almost no difference between the recovered oils by water and CO2, after which (> 3 years oil recovery by gas injection showed a significant increase. This may be due to the enhanced performance at the increased reservoir pressure during the first period. Maximum oil recovery is shown by miscible CO2 flooding of asphaltenic oil at combined temperatures and pressures of 50 °C/90 bar and 70 °C/120 bar (no significant difference between the two cases, about 1% compared to 80 °C/140 bar. This may support the positive influence of the high combined temperatures and pressures for the miscible CO2 flooding; however beyond a certain limit the oil recovery declined due to increased asphaltene deposition. Another interesting finding in this work is that for single phase oil, an almost linear relationship is observed between the pressure drop and the asphaltene deposition regardless of the flowing fluid pressure.

Distribution of metals in vacuum residuums, asphaltenes and maltenes by PIXE

International Nuclear Information System (INIS)

Romero G, E.T.; Camacho M, V.; Sanchez B, A.C.; Lopez M, J.; Ramirez T, J.J.; Villasenor S, P.; Aspiazu F, J.A.

2001-01-01

The PIXE technique for determining directly the distribution and abundance of trace metals in vacuum residuum, asphaltenes and maltenes separated with n-alkanes (C 5 -C 8 ) is used. The metal content of petroleum derivatives revealed that the vacuum residuum contains iron, aluminium, vanadium and nickel mainly, while that the asphaltenes and maltenes maintain inside of their composition only preferably the vanadium and nickel as majority elements. (Author)

Analysis of metals in asphaltenes of KU-46 by PIXE analysis; Analisis de metales en asfaltenos de crudo mexicano KU-46 por PIXE

Energy Technology Data Exchange (ETDEWEB)

Navidad G, P.; Pina L, L.I.; Lopez M, J.; Ramirez T, J.J.; Aspiazu F, J.A.; Romero G, E.T. [Gerencia de Ciencias Basicas, Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

2002-07-01

The content of metals of the asphaltenes obtained from the KU-46 mexican crude with n-heptane was evaluated. The found metals in higher concentration are transition metals as well as the vanadium, nickel, copper and zinc. Moreover the sulfur in high concentrations was quantified. The metallic content of the asphaltenes revealed that the crude contains a lower quantity of metals unlike the vacuum residue previously analysed. (Author)

Modeling of asphaltene and wax precipitation

Energy Technology Data Exchange (ETDEWEB)

Chung, F.; Sarathi, P.; Jones, R.

1991-01-01

This research project was designed to focus on the development of a predictive technique for organic deposition during gas injection for petroleum EOR. A thermodynamic model has been developed to describe the effects of temperature, pressure, and composition on asphaltene precipitation. The proposed model combines regular solution theory with Flory-Huggins polymer solutions theory to predict maximum volume fractions of asphaltene dissolved in oil. The model requires evaluation of vapor-liquid equilibria, first using an equation of state followed by calculations of asphaltene solubility in the liquid-phase. A state-of-the-art technique for C{sub 7+} fraction characterization was employed in developing this model. The preliminary model developed in this work was able to predict qualitatively the trends of the effects of temperature, pressure, and composition. Since the mechanism of paraffinic wax deposition is different from that of asphaltene deposition, another thermodynamic model based on the solid-liquid solution theory was developed to predict the wax formation. This model is simple and can predict the wax appearance temperature with reasonable accuracy. Accompanying the modeling work, experimental studies were conducted to investigate the solubility of asphaltene in oil land solvents and to examine the effects of oil composition, CO{sub 2}, and solvent on asphaltene precipitation and its properties. This research focused on the solubility reversibility of asphaltene in oil and the precipitation caused by CO{sub 2} injection at simulated reservoir temperature and pressure conditions. These experiments have provided many observations about the properties of asphaltenes for further improvement of the model, but more detailed information about the properties of asphaltenes in solution is needed for the development of more reliable asphaltene characterization techniques. 50 refs., 8 figs., 7 tabs.

Electrodeposition of Asphaltenes. 2. Effect of Resins and Additives

DEFF Research Database (Denmark)

Khvostichenko, Daria S; Andersen, Simon Ivar

2010-01-01

Electrodeposition of asphaltenes from oil/heptane, asphaltene/heptane, and asphaltene/heptane/additive mixtures has been investigated. Toluene, native petroleum resins, and a synthetic asphaltene dispersant, p-nonylphenol, were used as additives. The addition of these components led to partial...... dissolution of asphaltenes in heptane. The charge of asphaltenic particles was found to be negative in oil/heptane mixtures and positive in asphaltene/heptane mixtures. In asphaltene/heptane/toluene systems, the charge of the deposit varied from positive to neutral to negative, depending upon the method...

Influence of asphaltene aggregation and pressure on crude oil emulsion stability

Energy Technology Data Exchange (ETDEWEB)

Auflem, Inge Harald

2002-07-01

Water-in-crude oil emulsions stabilised by various surface-active components are one of the major problems in relation to petroleum production. This thesis presents results from high-pressure separation experiments on ''live'' crude oil and model oil emulsions, as well as studies of Interactions between various indigenous stabilising materials in crude oil. A high-pressure separation rig was used to study the influence of gas and gas bubbles on the separation of water-in-crude oil emulsions. The results were interpreted as a flotation effect from rising gas bubbles, which led to increased separation efficiency. The separation properties of a ''live'' crude oil were compared to crude oil samples recombined with various gases. The results showed that water-in-oil emulsions produced from the ''live'' crude oil samples, generally separated faster and more complete, than emulsions based on recombined samples of the same crude oil. Adsorption of asphaltenes and resins onto a hydrophilic surface from solutions with varying aromatic/aliphatic character was investigated by a quarts crystal microbalance. The results showed that asphaltenes adsorbed to a larger degree than the resins. The resins were unable to desorb pre-adsorbed asphaltenes from the surface, and neither did they adsorb onto the asphaltene-coated surface. In solutions of both of resins and asphaltenes the two constituents associated in bulk liquid and adsorbed to the surface in the form of mixed aggregates. Near infrared spectroscopy and pulsed field gradient spin echo nuclear magnetic resonance were used to study asphaltene aggregation and the influence of various amphiphiles on the asphaltene aggregate size. The results showed Interactions between the asphaltenes and various chemicals, which were proposed to be due to acid-base interactions. Among the chemicals used were various naphthenic acids. Synthesised monodisperse acids gave a reduction of size of the asphaltene aggregates, whereas polydisperse

Influence of asphaltene aggregation and pressure on crude oil emulsion stability

Energy Technology Data Exchange (ETDEWEB)

Auflem, Inge Harald

2002-07-01

Water-in-crude oil emulsions stabilised by various surface-active components are one of the major problems in relation to petroleum production. This thesis presents results from high-pressure separation experiments on ''live'' crude oil and model oil emulsions, as well as studies of Interactions between various indigenous stabilising materials in crude oil. A high-pressure separation rig was used to study the influence of gas and gas bubbles on the separation of water-in-crude oil emulsions. The results were interpreted as a flotation effect from rising gas bubbles, which led to increased separation efficiency. The separation properties of a ''live'' crude oil were compared to crude oil samples recombined with various gases. The results showed that water-in-oil emulsions produced from the ''live'' crude oil samples, generally separated faster and more complete, than emulsions based on recombined samples of the same crude oil. Adsorption of asphaltenes and resins onto a hydrophilic surface from solutions with varying aromatic/aliphatic character was investigated by a quarts crystal microbalance. The results showed that asphaltenes adsorbed to a larger degree than the resins. The resins were unable to desorb pre-adsorbed asphaltenes from the surface, and neither did they adsorb onto the asphaltene-coated surface. In solutions of both of resins and asphaltenes the two constituents associated in bulk liquid and adsorbed to the surface in the form of mixed aggregates. Near infrared spectroscopy and pulsed field gradient spin echo nuclear magnetic resonance were used to study asphaltene aggregation and the influence of various amphiphiles on the asphaltene aggregate size. The results showed Interactions between the asphaltenes and various chemicals, which were proposed to be due to acid-base interactions. Among the chemicals used were various naphthenic acids. Synthesised monodisperse acids gave a reduction of

Enhanced oil recovery (EOR) by miscible CO{sub 2} and water flooding of asphaltenic and non-asphaltenic oils

Energy Technology Data Exchange (ETDEWEB)

Chukwudeme, E. A.; Hamouda, A. A. [Department of Petroleum Engineering, University of Stavanger, 4036 Stavanger (Norway)

2009-07-01

An EOR study has been performed applying miscible CO{sub 2} flooding and compared with that for water flooding. Three different oils are used, reference oil (n-decane), model oil (n-C10, SA, toluene and 0.35 wt % asphaltene) and crude oil (10 wt % asphaltene) obtained from the Middle East. Stearic acid (SA) is added representing a natural surfactant in oil. For the non-asphaltenic oil, miscible CO{sub 2} flooding is shown to be more favourable than that by water. However, it is interesting to see that for first years after the start of the injection (< 3 years) it is shown that there is almost no difference between the recovered oils by water and CO{sub 2}, after which (> 3 years) oil recovery by gas injection showed a significant increase. This may be due to the enhanced performance at the increased reservoir pressure during the first period. Maximum oil recovery is shown by miscible CO{sub 2} flooding of asphaltenic oil at combined temperatures and pressures of 50 {sup o}C/90 bar and 70 {sup o}C/120 bar (no significant difference between the two cases, about 1%) compared to 80 {sup o}C/140 bar. This may support the positive influence of the high combined temperatures and pressures for the miscible CO{sub 2} flooding; however beyond a certain limit the oil recovery declined due to increased asphaltene deposition. Another interesting finding in this work is that for single phase oil, an almost linear relationship is observed between the pressure drop and the asphaltene deposition regardless of the flowing fluid pressure. (author)

Sans study of asphaltene aggregration

Energy Technology Data Exchange (ETDEWEB)

Overfield, R.E.; (Esso Resources Canada Ltd., Alberta); Sheu, E.Y.; Sinha, S.K.; Liang, K.S. (Exxon Research and Engineering Co., Annandale, NJ (USA))

1988-06-01

The colloidal properties of asphaltenes have long been recognized from peculiarities in their solubility and colligative properties. A layered micellar model for asphaltenes was proposed by Pfeiffer and Saal in 1940, in which a highly condensed alkyl aromatic formed the central part, and molecules of decreasingly aromatic character (resins) clustered around them. Numerous studies, based on a variety of techniques such as ultracentrifugation and electron microscopy indicated a particulate nature for asphaltenes with size 20-40 {angstrom} diameter. T.F. Yen and co-workers proposed a refined model based on x-ray diffraction and small angle scattering. In this model, interactions between flat sheets of condensed aromatic rings form the central crystallite part of a spherical particle with the outer part being comprised of the aliphatic positions of the same molecules. These particles are bunched together with some degree of entanglement into micelles. Concentration and solvent dependent radii of gyration, ranging from 30-50 {angstrom} were reported. The aggregation creates a good deal of uncertainty as to the true molecular size of weight of asphaltenes. Neutron scattering offers novel contrast relative to light scattering (refractive index) and x-ray scattering (electron density). This is because the scattering length of proton is negative, whereas that from deuterium and other nuclei such as C, S, O, and N are positive. Thus by replacing hydrogen with deuterium in either the solvent or the scatterer the contrast can be varied, and different parts of the molecule can be highlighted.

Sans study of asphaltene aggregation

Energy Technology Data Exchange (ETDEWEB)

Overfield, R.E.; Sheu, E.Y.; Sinha, S.K.; Liang, K.S. (Esso Resources Canada Ltd., 339-50 Avenue S.E., Calgary, Alberta T2G 2B3 (CA))

1988-06-01

The colloidal properties of asphaltenes have long been recognized from peculiarities in their solubility and colligative properties. A layered micellar model or asphaltenes was proposed by others in which a highly condensed alkyl aromatic formed the central part, and molecules of decreasingly aromatic character (resins) clustered around them. Numerous studies, based on a variety of techniques such as ultracentrifugation and electron microscopy indicated a particulate nature for asphaltenes with size 20-40 A diameter. Others have proposed a refined model based on x-ray diffraction and small angle scattering. In this model, interactions between flat sheets of condensed aromatic rings form the central ''crystallite'' part of a spherical particle with the outer part being comprised of the aliphatic positions of the same molecules. These particles are bunched together with some degree of entanglement into ''micelles''. Concentration and solvent dependent radii of gyration, ranging from 30-50 A were reported. The aggregation creates a good deal of uncertainty as to the true molecular size or weight of asphaltenes. Neutron scattering offers novel contrast relative to light scattering (refractive index) and x-ray scattering (electron density). This is because the scattering length of proton is negative, whereas that from deuterium and other nuclei such as C, S, O, and N are positive. Thus by replacing hydrogen with deuterium in either the solvent or the scatterer the contrast can be varied, and different parts of the molecule can be highlighted.

Isolation of Asphaltene-Degrading Bacteria from Sludge Oil

Directory of Open Access Journals (Sweden)

Pingkan Aditiawati

2015-03-01

Full Text Available Sludge oil contains 30%–50% hydrocarbon fractions that comprise saturated fractions, aromatics, resins, and asphaltene. Asphaltene fraction is the most persistent fraction. In this research, the indigenous bacteria that can degrade asphaltene fractions from a sludge oil sample from Balikpapan that was isolated using BHMS medium (Bushnell-Hass Mineral Salt with 0.01% (w/v yeast extract, 2% (w/v asphaltene extract, and 2% (w/v sludge oil. The ability of the four isolates to degrade asphaltene fractions was conducted by the biodegradation asphaltene fractions test using liquid cultures in a BHMS medium with 0.01% (w/v yeast extract and 2% (w/v asphaltene extract as a carbon source. The parameters measured during the process of biodegradation of asphaltene fractions include the quantification of Total Petroleum Hydrocarbon (g, log total number of bacteria (CFU/ml, and pH. There are four bacteria (isolates 1, 2, 3, and 4 that have been characterized to degrade asphaltic fraction and have been identified as Bacillus sp. Lysinibacillus fusiformes, Acinetobacter sp., and Mycobacterium sp., respectively. The results showed that the highest ability to degrade asphaltene fractions is that of Bacillus sp. (isolate 1 and Lysinibacillus fusiformes (Isolate 2, with biodegradation percentages of asphaltene fractions being 50% and 55%, respectively, and growth rate at the exponential phase is 7.17x107 CFU/mL.days and 4.21x107 CFU/mL.days, respectively.

Behavior of asphaltene model compounds at w/o interfaces.

Science.gov (United States)

Nordgård, Erland L; Sørland, Geir; Sjöblom, Johan

2010-02-16

Asphaltenes, present in significant amounts in heavy crude oil, contains subfractions capable of stabilizing water-in-oil emulsions. Still, the composition of these subfractions is not known in detail, and the actual mechanism behind emulsion stability is dependent on perceived interfacial concentrations and compositions. This study aims at utilizing polyaromatic surfactants which contains an acidic moiety as model compounds for the surface-active subfraction of asphaltenes. A modified pulse-field gradient (PFG) NMR method has been used to study droplet sizes and stability of emulsions prepared with asphaltene model compounds. The method has been compared to the standard microscopy droplet counting method. Arithmetic and volumetric mean droplet sizes as a function of surfactant concentration and water content clearly showed that the interfacial area was dependent on the available surfactant at the emulsion interface. Adsorption of the model compounds onto hydrophilic silica has been investigated by UV depletion, and minor differences in the chemical structure of the model compounds caused significant differences in the affinity toward this highly polar surface. The cross-sectional areas obtained have been compared to areas from the surface-to-volume ratio found by NMR and gave similar results for one of the two model compounds. The mean molecular area for this compound suggested a tilted geometry of the aromatic core with respect to the interface, which has also been proposed for real asphaltenic samples. The film behavior was further investigated using a liquid-liquid Langmuir trough supporting the ability to form stable interfacial films. This study supports that acidic, or strong hydrogen-bonding fractions, can promote stable water-in-oil emulsion. The use of model compounds opens up for studying emulsion behavior and demulsifier efficiency based on true interfacial concentrations rather than perceived interfaces.

Characterisation of crude oil components, asphaltene aggregation and emulsion stability by means of near infrared spectroscopy and multivariate analysis

Energy Technology Data Exchange (ETDEWEB)

Aske, Narve

2002-06-01

Effective separation of water-in-crude oil emulsions is a central challenge for the oil industry on the Norwegian Continental Shelf, especially with the future increase in subsea and even down-hole processing of well fluids. The mechanisms and properties governing emulsion stability are far from fully understood but the indigenous surface active crude oil components are believed to play a major role. In this work a thorough physico-chemical characterisation of a set of crude oils originating from a variety of production fields has been performed. Crude oil properties responsible for emulsion stability were identified by use of multivariate analysis techniques like partial least squares regression (PLS) and principal component analysis (PCA). Interfacial elasticity along with both asphaltene content and asphaltene aggregation state were found to be main contributors to emulsion stability. Information on a crude oils ability to form elastic crude oil-water interfaces was found to be especially crucial when discussing emulsion stability. However, measured values of interfacial elasticity were highly dependent on asphaltene aggregation state. Several experimental techniques was utilised and partly developed for the crude oil characterisation. A high-pressure liquid chromatography (HPLC) scheme was developed for SARA-fractionation of crude oils and an oscillating pendant drop tensiometer was used for characterisation of interfacial rheological properties. For emulsion stability a cell for determining the stability as a function of applied electric fields was used. In addition, near infrared spectroscopy (NIR) was used throughout the work both for chemical and physical characterisation of crude oils and model systems. High pressure NIR was used to study the aggregation of asphaltenes by pressure depletion. A new technique for detection of asphaltene aggregation onset pressures based on NIR combined with PCA was developed. It was also found that asphaltene aggregation is

Compositional thermodynamic model of asphaltenes flocculation out of crudes; Modelisation thermodynamique compositionnelle de la floculation des bruts asphalteniques

Energy Technology Data Exchange (ETDEWEB)

Szewczyk, V

1997-12-02

The aim of this work is to propose to the oil industry a compositional thermodynamic model able to predict the operating conditions which induce asphaltenes flocculation out of crudes. In this study, various analytical methods (calorimetry, elemental analysis, {sup 13}C nuclear magnetic resonance, neutron diffusion,...) have been used in order to get a better description of the asphaltene fraction to infer its flocculation mechanism. The proposed model describes this flocculation as a thermodynamic transition inducing the formation of a new liquid phase with a high asphaltene content and formed by all the components initially in the crude: the asphaltene deposit. Asphaltenes are represented as a pseudo-component essentially made of carbon and hydrogen. The analytical modelling of the F11-F20 light fraction is the one proposed by Jaubert (1993). The F20+ heavy fraction is represented by four pseudo-components, their physical properties are calculated using the group contribution methods of Avaullee (1995) and of Rogalski and Neau (1990). The Peng-Robinson equation of state (1976) combined with the Abdoul and Peneloux group contribution mixing rules (1989) is used in order to restitute the gas-liquid-asphaltene deposit phase equilibria. This model not being able to compute flocculation conditions on a predictive manner, the method consists in fitting some physical properties of the pseudo-components introduced in the analytical representation of the asphaltene crudes. he obtained results show results show that the proposed flocculation model is then well adapted to the description of the thermodynamic properties (saturation pressures, relative volumes, flocculation curves) of asphaltene crudes within a relatively large range of temperature (30-150 deg C) and pressure (0.1-50 MPa), covering the majority of conditions met in oil production. (author) 109 refs.

Raman spectrum of asphaltene

KAUST Repository

Abdallah, Wael A.

2012-11-05

Asphaltenes extracted from seven different crude oils representing different geological formations from around the globe were analyzed using the Raman spectroscopic technique. Each spectrum is fitted with four main peaks using the Gaussian function. On the basis of D1 and G bands of the Raman spectrum, asphaltene indicated an ordered structure with the presence of boundary defected edges. The average aromatic sheet size of the asphaltene molecules is estimated within the range of 1.52-1.88 nm, which represents approximately seven to eight aromatic fused rings. This estimation is based on the integrated intensity of D1 and G bands, as proposed by Tunistra and Koenig. The results here are in perfect agreement with so many other used techniques and indicate the potential applicability of Raman measurements to determine the average aromatic ring size and its boundary. © 2012 American Chemical Society.

Raman spectrum of asphaltene

KAUST Repository

Abdallah, Wael A.; Yang, Yang

2012-01-01

Asphaltenes extracted from seven different crude oils representing different geological formations from around the globe were analyzed using the Raman spectroscopic technique. Each spectrum is fitted with four main peaks using the Gaussian function. On the basis of D1 and G bands of the Raman spectrum, asphaltene indicated an ordered structure with the presence of boundary defected edges. The average aromatic sheet size of the asphaltene molecules is estimated within the range of 1.52-1.88 nm, which represents approximately seven to eight aromatic fused rings. This estimation is based on the integrated intensity of D1 and G bands, as proposed by Tunistra and Koenig. The results here are in perfect agreement with so many other used techniques and indicate the potential applicability of Raman measurements to determine the average aromatic ring size and its boundary. © 2012 American Chemical Society.

Asphaltenes-based polymer nano-composites

Science.gov (United States)

Bowen, III, Daniel E

2013-12-17

Inventive composite materials are provided. The composite is preferably a nano-composite, and comprises an asphaltene, or a mixture of asphaltenes, blended with a polymer. The polymer can be any polymer in need of altered properties, including those selected from the group consisting of epoxies, acrylics, urethanes, silicones, cyanoacrylates, vulcanized rubber, phenol-formaldehyde, melamine-formaldehyde, urea-formaldehyde, imides, esters, cyanate esters, allyl resins.

The use of stability indices in predicting asphaltene problems in upstream and downstream oil operations

Energy Technology Data Exchange (ETDEWEB)

Asomaning, S. [Baker Petrolite, Sugar Land, TX (United States)

2003-07-01

A series of test methods have been developed to determine the stability of asphaltenes in crude oils. They were developed due to the high cost of remediating asphaltene deposition in offshore operations. This study described the characteristics of the Oliensis Spot Test, two saturates, aromatics, resins and asphaltenes (SARA)-based screens (the Colloidal Instability Index and Asphaltene-Resin ratio), a solvent titration method with near infrared radiation (NIR) solids detection, and live oil depressurization. Each method is used to predict the stability of asphaltenes in crude oils with different API gravity. A complete description of the test methods was provided along with experimental data. The effectiveness of the different tests in predicting the stability of asphaltenes in crude oils was also assessed. Results indicate that the prediction of a crude oil's tendency towards asphaltene precipitation was more accurate with the Colloidal Instability Index and the solvent titration method. Live oil depressurization proved to be very effective in predicting the stability of asphaltenes for light oils, where most stability tests fail. tabs., figs.

Separation and characterization of asphaltenic subfractions

Energy Technology Data Exchange (ETDEWEB)

Honse, Siller O.; Ferreira, Silas R.; Mansur, Claudia R. E.; Lucas, Elizabete F. [Universidade Federal do Rio de Janeiro (IMA/UFRJ), RJ (Brazil). Inst. de Macromoleculas Professora Eloisa Mano; Gonzalez, Gaspar, E-mail: elucas@ima.ufrj.br [Centro de Pesquisas da PETROBRAS (CENPES), Rio de Janeiro, RJ (Brazil)

2012-07-01

The structure of the various asphaltenic subfractions found in crude oil was evaluated. For this purpose, C5 asphaltenes were extracted from an asphaltic residue using n-pentane as the flocculant solvent. The different subfractions were isolated from the C5 asphaltenes by the difference in solubility in different solvents. These were characterized by infrared spectroscopy, nuclear magnetic resonance, X-ray fluorescence, elementary analysis and mass spectrometry. The results confirmed that the subfractions extracted with higher alkanes had greater aromaticity and molar mass. However, small solubility variations between the subfractions were attributed mainly to the variation in the concentrations of cyclical hydrocarbon compounds and metals (author)

The Critical Micelle Concentration of Asphaltenes as Measured by Calorimetry

DEFF Research Database (Denmark)

Andersen, Simon Ivar; Christensen, S. D.

2000-01-01

Micellization of asphaltenes in solution has been investigated using a micro calorimetric titration procedure (Andersen, S. I.; Birdi, K. S. J Colloid Interface Sci. 1991, 142, 497). The method uses the analysis of heat of dissociation and dilution of asphaltene micelles when a pure solvent (or...... solvent mixture) is titrated with a solution of asphaltene in the same solvent. The asphaltene concentration of the injected solution is at a level above the critical micelle concentration (CMC). In the present paper the procedure is applied in investigation of asphaltenes as well as subfractions...

Phase Behavior Modeling of Asphaltene Precipitation for Heavy Crudes: A Promising Tool Along with Experimental Data

Science.gov (United States)

Tavakkoli, M.; Kharrat, R.; Masihi, M.; Ghazanfari, M. H.; Fadaei, S.

2012-12-01

Thermodynamic modeling is known as a promising tool for phase behavior modeling of asphaltene precipitation under different conditions such as pressure depletion and CO2 injection. In this work, a thermodynamic approach is used for modeling the phase behavior of asphaltene precipitation. The precipitated asphaltene phase is represented by an improved solid model, while the oil and gas phases are modeled with an equation of state. The PR-EOS was used to perform flash calculations. Then, the onset point and the amount of precipitated asphaltene were predicted. A computer code based on an improved solid model has been developed and used for predicting asphaltene precipitation data for one of Iranian heavy crudes, under pressure depletion and CO2 injection conditions. A significant improvement has been observed in predicting the asphaltene precipitation data under gas injection conditions. Especially for the maximum value of asphaltene precipitation and for the trend of the curve after the peak point, good agreement was observed. For gas injection conditions, comparison of the thermodynamic micellization model and the improved solid model showed that the thermodynamic micellization model cannot predict the maximum of precipitation as well as the improved solid model. The non-isothermal improved solid model has been used for predicting asphaltene precipitation data under pressure depletion conditions. The pressure depletion tests were done at different levels of temperature and pressure, and the parameters of a non-isothermal model were tuned using three onset pressures at three different temperatures for the considered crude. The results showed that the model is highly sensitive to the amount of solid molar volume along with the interaction coefficient parameter between the asphaltene component and light hydrocarbon components. Using a non-isothermal improved solid model, the asphaltene phase envelope was developed. It has been revealed that at high temperatures, an

Investigation of Asphaltene Precipitation at Elevated Temperature

DEFF Research Database (Denmark)

Andersen, Simon Ivar; Lindeloff, Niels; Stenby, Erling Halfdan

1998-01-01

In order to obtain quantitative data on the asphaltene precipitation induced by the addition of n-alkane (heptane) at temperatures above the normal boiling point of the precipitant, a high temperature/high pressure filtration apparatus has been constructed. Oil and alkane are mixed...

Study on the polarity, solubility, and stacking characteristics of asphaltenes

KAUST Repository

Zhang, Long-li; Yang, Guo-hua; Wang, Ji-Qian; Li, Yan; Li, Li; Yang, Chao-he

2014-01-01

The structure and transformation of fused aromatic ring system in asphaltenes play an important role in the character of asphaltenes, and in step affect the properties of heavy oils. Polarity, solubility and structural characteristics of asphaltenes

Hydrodynamic perspective on asphaltene agglomeration and deposition

NARCIS (Netherlands)

Schutte, K.C.J.; Portela, L.M.; Twerda, A.; Henkes, R.A.W.M.

2015-01-01

In this work, we propose a detailed numerical model for asphaltene agglomeration and deposition, as induced by a resolved turbulent liquid carrier phase flow, in which transport, breakup, and re-entrainment are also taken into account. Asphaltene phase separation is represented by the appearance of

A theory of phase separation in asphaltene-micellar solutions

Energy Technology Data Exchange (ETDEWEB)

Pacheco Sanchez, Juan H. [Instituto Mexicano del Petroleo, Mexico D.F. (Mexico)

2001-08-01

A theory of phase separation in micellar solutions of asphaltene in aromatic hydrocarbons was reported in this paper, based on both the approach of the phase behavior of amphiphile/water micelles, and the self-association of asphaltene in aromatic core. Several experimental techniques have been used by different investigators showing the existence of some kind of critical micellar concentration (CMC) on asphaltenes in aromatic solutions. So, at least asphaltene-monomer and asphaltene-micellar phases are experimentally demonstrated facts. These two phases are the main purpose in this report on a theoretical model. Some results show the temperature versus asphaltene concentration phase diagram. The phase diagram is examined against the limited critical micelle concentration data for asphaltenes-in-toluene systems. Such phase diagram is also qualitatively examined against an experimental demonstration of phase separation. The asphaltene-micelle growth depends on the parameter K responsible for the shape and size of it. At the same time, parameter K depends on both the number of asphaltene-monomer associated in the asphaltene-micelle, and the chemical potentials in the interior and in the periphery of the micelle. An expression for getting the number of asphaltene-monomers self-associated in the asphaltene-micelle was obtained. [Spanish] Se reporta una teoria de separacion de fases en soluciones micelares de asfalteno en hidrocarburos aromaticos, basada tanto en la conducta de fase de micelas formadas por anififilos en agua como en la autoasociacion de asfaltenos en nucleos aromaticos. Se han usado diversas tecnicas experimentales por diferentes investigadores que demuestran la existancia de algun tipo de concentracion micelar critica (CMC) de soluciones de asfaltenos en aromaticos. Entonces, al menos las fases de asfalteno-monomerico y de asfalteno-micelar son hechos experimentalmente demostrados. Esta dos fases son el principal proposito de este reporte en un modelo

Enhancing the Effectiveness of Carbon Dioxide Flooding by Managing Asphaltene Precipitation; FINAL

International Nuclear Information System (INIS)

Deo, Milind D.

2002-01-01

This project was undertaken to understand fundamental aspects of carbon dioxide (CO2) induced asphaltene precipitation. Oil and asphaltene samples from the Rangely field in Colorado were used for most of the project. The project consisted of pure component and high-pressure, thermodynamic experiments, thermodynamic modeling, kinetic experiments and modeling, targeted corefloods and compositional modeling

Screening of inhibitors for remediation of asphaltene deposits: Experimental and modeling study

Directory of Open Access Journals (Sweden)

Mehdi Madhi

2018-06-01

Full Text Available One of the most severe problems during production from heavy crude oil reservoirs is the formation of asphaltene precipitation and as a result deposition in the tubing, surface facilities and near wellbore region which causes oil production and permeability reduction in addition to rock wettability alteration in the reservoir. So one of the economical ways to prevent such incidents is using the chemicals which are called asphaltene inhibitor.In this study, the influence of three commercial inhibitors, namely; Cetyl Terimethyl Ammonium Bromide (CTAB, Sodium Dodecyl Sulfate (SDS, Triton X-100 and four non-commercial (Benzene, Benzoic Acid, Salicylic Acid, Naphthalene inhibitors on two Iranian crude oils were investigated. This study extends previous works and contributes toward the better understanding of interactions between asphaltene and inhibitor. Effect of functional groups and structure of inhibitors on asphaltene precipitation were studied and it seems clear that the nature and polarity of asphaltene (structure and amount of impurities presented has a significant impact on the selection of inhibitors. asphaltene dispersant tests and Core flood tests were designed for evaluation of inhibitors in static and dynamic conditions. The results revealed distinguished mechanisms for asphaltene solubilization/dispersion (such as hydrogen bonding, π–π interaction and acid-base interaction and influence of additional side group (OH on inhibition power of inhibitor.During the experiments, it was found that increasing inhibitor concentration may lead to the self-assembly of inhibitor and declining of asphaltene stabilization. So, finding optimum concentration of inhibitor with high efficiency and available at a reasonable price is very important. The results suggest that 600 ppm of CTAB and 300 ppm of SDS were approximately optimum concentrations for the studied crude oils. One of the most important findings that differ from previous studies is the

Investigating Asphaltenes Composition in Crude Oil Samples using ...

African Journals Online (AJOL)

MBI

2015-12-22

Dec 22, 2015 ... composition of asphaltenes by Iatroscan TLC-FID method was compared with the weight% of asphaltenes precipitated. ... SARA in the crude oil samples were determined in this work ..... Fractionation and characterization of.

Characterization of asphaltenes by nonaqueous capillary electrophoresis

NARCIS (Netherlands)

Kok, W.T.; Tüdös, A.J.; Grutters, M.; Shepherd, A.G.

2011-01-01

Nonaqueous capillary electrophoresis was used for the separation and characterization of asphaltene samples from different sources. For the separation medium (background electrolyte), mixtures of tetrahydrofuran and a high-permittivity organic solvent could be used. The best results were obtained

Sizes of vanadyl petroporphyrins and asphaltene aggregates in toluene

Energy Technology Data Exchange (ETDEWEB)

Dechaine, Greg Paul; Gray, Murray R. [Department of Chemical and Materials Engineering, University of Alberta (Canada)], email: gpd@ualberta.ca

2010-07-01

This work focuses on the importance of removing vanadyl porphyrins components from crude oils and the methodology for doing it. The diffusion of asphaltene and vanadium components in diluted toluene was measured using a stirred diaphragm diffusion cell, which was equipped with a number of different cellulosic membranes of different pore size. In-situ UV/visible spectroscopy was used to observe filtrates of the process. The effective diffusivity of asphaltene structures was plotted for different pore sized membranes. It was noticed that asphaltene concentrations increased with increased pore sizes; particularly increasing at pore diameter of 5 nm. Moreover the effects of temperature and mass concentration were also investigated in this study. It was shown that increasing the temperature of the toluene causes the mobility of asphaltene to increase as well. Nevertheless, decreasing the concentration of asphaltene does not affect its mobility. It was shown that toluene samples from different sources showed different mobility.

Study on the polarity, solubility, and stacking characteristics of asphaltenes

KAUST Repository

Zhang, Long-li

2014-07-01

The structure and transformation of fused aromatic ring system in asphaltenes play an important role in the character of asphaltenes, and in step affect the properties of heavy oils. Polarity, solubility and structural characteristics of asphaltenes derived from Tahe atmospheric residue (THAR) and Tuo-826 heavy crude oil (Tuo-826) were analyzed for study of their internal relationship. A fractionation method was used to separate the asphaltenes into four sub-fractions, based on their solubility in the mixed solvent, for the study of different structural and physical-chemical properties, such as polarity, solubility, morphology, stacking characteristics, and mean structural parameters. Transmission electron microscope (TEM) observation can present the intuitive morphology of asphaltene molecules, and shows that the structure of asphaltenes is in local order as well as long range disorder. The analysis results showed that n-heptane asphaltenes of THAR and Tuo-826 had larger dipole moment values, larger fused aromatic ring systems, larger mean number of stacking layers, and less interlayer spacing between stacking layers than the corresponding n-pentane asphaltenes. The sub-fractions that were inclined to precipitate from the mixture of n-heptane and tetrahydrofuran had larger polarity and less solubility. From the first sub-fraction to the fourth sub-fraction, polarity, mean stacking numbers, and average layer size from the TEM images follow a gradual decrease. The structural parameters derived from TEM images could reflect the largest fused aromatic ring system in asphaltene molecule, yet the parameters derived from 1H NMR data reflected the mean message of poly-aromatic ring systems. The structural parameters derived from TEM images were more consistent with the polarity variation of sub-fractions than those derived from 1H NMR data, which indicates that the largest fused aromatic ring system will play a more important role in the stacking characteristics of

Molecular-weight distributions of coal and petroleum asphaltenes from laser desorption/ionization experiments

Energy Technology Data Exchange (ETDEWEB)

Ana R. Hortal; Paola Hurtado; Bruno Martinez-Haya; Oliver C. Mullins [Universidad Pablo de Olavide, Seville (Spain). Departamento de Sistemas Fisicos, Quimicos y Naturales

2007-09-15

Molecular-weight distributions (MWDs) of asphaltenes extracted from coal and petroleum have been measured in laser desorption/ionization (LDI) mass spectrometric experiments. The dried-droplet and solvent-free sample preparation methods are compared. The coal asphaltenes have a relatively narrow MWD (full width 150 amu) with an average molecular weight of 340 amu. The petroleum asphaltenes display a broader MWD (full width 300 amu) and are heavier on average (680 amu). The LDI spectra also provide evidence for the formation of noncovalent clusters of the two types of asphaltenes during the desorption process. Petroleum and coal asphaltenes exhibit aggregation as do large model polycyclic aromatic hydrocarbons (PAHs) with five or more fused rings also included in the study. Smaller PAHs (pyrene) exhibit less aggregation, especially when alkane-chain substituents are incorporated to the molecular structure. This indicates that asphaltenes possess large PAHs and, according to the relatively small molecular weights observed, that there is a preponderance of asphaltene molecules with only a single fused ring system. The coal asphaltenes present a significantly smaller propensity toward aggregation than their crude oil counterparts. This finding, coupled with the fact that (1) alkanes inhibit aggregation in LDI and (2) petroleum asphaltenes possess much more alkane carbon, indicates that coal asphaltenes have smaller PAHs on average than petroleum asphaltenes. This is further corroborated by the stronger ultraviolet absorbance of the coal asphaltenes at wavelengths shorter than 400 nm. 32 refs., 8 figs.

Effect of asphaltenes on crude oil wax crystallization

DEFF Research Database (Denmark)

Kriz, Pavel; Andersen, Simon Ivar

2005-01-01

The paper summarizes the experimental work done on asphaltene influenced wax crystallization. Three different asphaltenes (from stable oil, instable oil, and deposit) were mixed at several concentrations or dispersions into the waxy crude oil. These blends were evaluated by viscometry and yield s...

Pyrolysis of petroleum asphaltenes from different geological origins ...

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science; Volume 33; Issue 4. Pyrolysis of petroleum asphaltenes from different geological origins and use of methylnaphthalenes and methylphenanthrenes as maturity indicators for asphaltenes. Manoj Kumar Sarmah Arun Borthakur Aradhana Dutta. Fuel Cells Volume 33 Issue 4 ...

Pyrolysis of petroleum asphaltenes from different geological origins

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science; Volume 36; Issue 2. Pyrolysis of petroleum asphaltenes from different geological origins and use of methylnaphthalenes and methylphenanthrenes as maturity indicators for asphaltenes. Manoj Kumar Sarmah Arun Borthakur Aradhana Dutta. Volume 36 Issue 2 April 2013 pp ...

Extraction and characterization of crude oil asphaltenes sub fractions; Extracao e caracterizacao de subfracoes de asfaltenos de petroleo

Energy Technology Data Exchange (ETDEWEB)

Ferreira, Silas R.; Calado, Lucas S.; Honse, Siller O.; Mansur, Claudia R.E.; Lucas, Elizabete F., E-mail: silas@ima.ufrj.br [Universidade Federal do Rio de Janeiro, Instituto de Macromoleculas, Laboratorio de Macromoleculas e Coloides na Industria de Petroleo, Rio de Janeiro, RJ (Brazil)

2011-07-01

Asphaltenes from crude oil have been studied for a long time. However, until today their chemical structures and physical-chemical properties are not well established. Nowadays, it is accepted that asphaltenes are dispersed in the crude oil as macro structures, which are mainly constituted of some condensed aromatic rings (about 6-20), containing aliphatic or naphthenic groups. The asphaltenes are also defined as the crude oil fraction that is insoluble in low molar mass n-alkanes and soluble in aromatic solvents, like benzene and toluene In order to investigate the molecular structure, in this work the asphaltenes were separated by using a different procedure as that normally described in the literature and characterized by infrared spectrometry, nuclear magnetic resonance, x-ray fluorescence, elemental analyses and particle size and size distribution. The difference in subfractions polarity can be attributed not only to the aromaticity changes but also to the content of elements, such as N, O, Fe, V, Si e Ni. (author)

Surface characterization of adsorbed asphaltene on a stainless steel surface

International Nuclear Information System (INIS)

Abdallah, W.A.; Taylor, S.D.

2007-01-01

X-ray photoelectron spectroscopy was used to characterize a single layer of adsorbed asphaltene on a metallic surface. The deposits were created by immersing a stainless steel disc into a dilute asphaltene solution with either toluene or dichloromethane as the solvent, although the toluene solution allowed for better control of the adsorbed asphaltene layer and less atmospheric oxygen contamination. The analyses for C 1s, S 2p 3/2 , N 1s and O 1s photoemission peaks indicated that different functional groups are present in the asphaltene layer including carboxylic, pyrrolic, pyridininc, thiophenic and sulfite, with slight differences in their binding energies

Study on the dipole moment of asphaltene molecules through dielectric measuring

KAUST Repository

Zhang, Long Li; Yang, Chao He; Wang, Ji Qian; Yang, Guo Hua; Li, Li; Li, Yan Vivian; Cathles, Lawrence

2015-01-01

The polarity of asphaltenes influences production, transportation, and refining of heavy oils. However, the dipole moment of asphaltene molecules is difficult to measure due to their complex composition and electromagnetic opaqueness. In this work, we present a convenient and efficient way to determine the dipole moment of asphaltene in solution by dielectric measurements alone without measurement of the refractive index. The dipole moment of n-heptane asphaltenes of Middle East atmospheric residue (MEAR) and Ta-He atmospheric residue (THAR) are measured within the temperature range of -60°C to 20°C. There is one dielectric loss peak in the measured solutions of the two types of asphaltene at the temperatures of -60°C or -40°C, indicating there is one type of dipole in the solution. Furthermore, there are two dielectric loss peaks in the measured solutions of the two kinds of asphaltene when the temperature rises above -5°C, indicating there are two types of dipoles corresponding to the two peaks. This phenomenon indicates that as the temperature increases above -5°C, the asphaltene molecules aggregate and present larger dipole moment values. The dipole moments of MEAR C7-asphaltene aggregates are up to 5 times larger than those before aggregation. On the other hand, the dipole moments of the THAR C7-asphaltene aggregates are only 3 times larger than those before aggregation. It will be demonstrated that this method is capable of simultaneously measuring multi dipoles in one solution, instead of obtaining only the mean dipole moment. In addition, this method can be used with a wide range of concentrations and temperatures.

Adsorption and wettability study of methyl ester sulphonate on precipitated asphaltene

International Nuclear Information System (INIS)

Okafor, H E; Gholami, R; Sukirman, Y

2016-01-01

Asphaltene precipitation from crude oil and its subsequent aggregation forms solid, which preferentially deposit on rock surfaces causing formation damage and wettability changes leading to loss of crude oil production. To resolve this problem, asphaltene inhibitor has been injected into the formation to prevent the precipitation of asphaltene. Asphaltene inhibitors that are usually employed are generally toxic and non-biodegradable. This paper presents a new environmentally friendly asphaltene inhibitor (methyl ester sulphonate), an anionic surfactant, which has excellent sorption on formation rock surfaces. Result from adsorption study validated by Langmuir and Freundlich models indicate a favourable adsorption. At low volumes injected, methyl ester sulphonate is capable of reverting oil-wet sandstone surface to water-wet surface. Biodegradability test profile shows that for concentrations of 100-5000ppm it is biodegradable by 65-80%. (paper)

Pyrolysis of petroleum asphaltenes from different geological origins ...

Indian Academy of Sciences (India)

terrestrial nature of the organic matter. Keywords. ... well as being of high molecular weight (Nali et al 1995). .... tially found in the organic matter of terrestrial source rocks, ..... Bunger J W and Li N C 1984 Chemistry of asphaltenes (Washington.

Experimental investigation on the effect of ultrasonic waves on reducing asphaltene deposition and improving oil recovery under temperature control.

Science.gov (United States)

Rezaei Dehshibi, Reza; Mohebbi, Ali; Riazi, Masoud; Niakousari, Mehrdad

2018-07-01

A well-known complication in the oil reservoir during oil production is asphaltene deposition in and around the production wellbore. Deposition of asphaltene around the production wellbore may cause a significant pressure drop and in turn loss of efficiency in the production process. Various mechanical and chemical methods have been employed in order to reduce asphaltene formation or to eliminate the precipitate. A novel technique which presented a great potential for prevention or elimination of asphaltene is spreading out the high energy ultrasound wave within the oil reservoir. In this study, in a glass micro-model, asphaltene precipitation was first simulated in a transparent porous medium and its removal by application of high energy ultrasound wave was then investigated. To simulate asphaltene precipitation, the micro-model was first saturated with oil and then a normal-pentane was injected. This was followed by flooding the porous media with brine while propagating ultrasound waves (30 kHz and 100 W) to eliminate asphaltene precipitation. The experiment setup was equipped with a temperature controller. The results indicate a significant reduction in asphaltene precipitation in the oil reservoir may be achieved by application of ultrasound energy. Asphaltene particle deposition has been solved reversibly in the oil layer of porous medium and with the oil layering mechanism, the rate of oil production has been increased. In some spots, water/oil emulsion has been formed because of the ultrasonic vibration on the wall. Both the crude and synthetic oils were examined. Copyright © 2018 Elsevier B.V. All rights reserved.

Prediction of the Gas Injection Effect on the Asphaltene Phase Envelope

Directory of Open Access Journals (Sweden)

Bahrami Peyman

2015-11-01

Full Text Available Asphaltene instability may occur when pressure, temperature and compositional variations affect the reservoir oil. Permeability reduction, wettability alteration, and plugging of wells and flow lines are the consequences of this phenomenon. Therefore, it is crucial to investigate the asphaltene behavior in different thermodynamic conditions by knowing the Asphaltene Precipitation Envelope (APE in a preventive way rather than the costly clean-up procedures. The selected reservoir oil has faced a remarkable decline in production due to several years of extraction, and Enhanced Oil Recovery (EOR has been considered as a solution. Therefore, in this paper, a comprehensive study was carried out to predict the effects of different injected gases on asphaltene onset and to prevent future asphaltene precipitation based on the laboratory data. The Advanced Redlich-Kwong-Soave (RKSA equation of state was considered to develop APE using Multiflash (Infochem Co.. For the selected reservoir oil, with temperature reduction at low temperatures, asphaltene precipitation weakened and made the onset pressure decrease, so this behavior is different from the results obtained in other published reports. On the basis of this model, several sensitivity analyses were performed with different gases (i.e., methane, CO2, N2 and associated gases to compare the risk of each gas for future EOR strategies. APE tend to expand as the amount of injected gases increases, except for CO2 gas injection, that showed another unconventional behavior for this crude oil. It was observed that for CO2 gas injection below a certain temperature, asphaltene stability increased, which can be considered as a good inhibitor of asphaltene precipitation.

Separation and characterization of resins and asphaltenes coming from Castilla crude Evaluation of their molecular interaction

International Nuclear Information System (INIS)

Navarro, Lina; Alvarez, Mario; Grosso, Jorge Luis; Navarro, Uriel

2004-01-01

The study of resins and asphaltenes, the heaviest fractions of oil, has become an area of interest due to the abundance of heavy crude oils in Colombia and Latin America. We studied the chemical composition of the heavy fractions of Castilla crude oil, evaluated some of its molecular parameters and found evidence of the interaction between the resins extracted from the crude with the asphaltenes of the original crude. With this objective, we carried out at the pilot plant level precipitation of the resin-asphaltene (R-A) aggregate by adding and mixing under controlled conditions, a paraffin solvent, from the Apiay refinery, called Apiasol. By extracting Soxhlet with the same solvent, resin 1 of aggregate R-A was separated. Resin ll defined as the soluble fraction that is part of the maltenes, was separated from the deasphalted crude by open column chromatography, using alumina as support, according to the SAR method (Saturated, Aromatics, Resins). The fractions of resins and the asphaltenes obtained, were characterized by: Nuclear Magnetic Resonance (NMR), FT-lR, DRX, elementary analysis (C, H, N, S), metal content (Ni and V), distribution of molecular weight by GPC, and average molecular weight by VPO. The results obtained show evidence that resin l which is part of the aggregate has less average molecular weight than resin ll which is present in the fraction of maltenes. In addition, some changes were found in the elementary analysis of among the resins. On the one hand, and taking into account the existing theories of molecular interactions among these fractions, it was found that the resins l separated from the R-A aggregate, when added to the crude, they stabilize their asphaltenes. This evaluation was carried out by analyzing the flocculation point of the crude and its mixtures with 1,9% and 3,8% of resin l, when they are titrated with a precipitating agent in an NIR cell that works with high pressure and temperature

Syngas obtainment from the gasification of asphaltenes of the San Fernando crude oil

International Nuclear Information System (INIS)

Moreno A, Laura; Rodriguez C, Fabio; Afanador R, Luz E; Grosso V, Jorge

2010-01-01

In this work, we developed the first study in Colombia to obtain and evaluate syngas compositions derived from asphaltenes gasification. These asphaltenes came from the implementation of a Deasphalting process to San Fernando crude oil, with the purpose of looking for technological options for their utilization. We performed the design, installation and commissioning of facilities for the gasification of asphaltenes at laboratory scale, it following an experimental methodology, performing nine tests and considering temperature and agent gasification quantity (oxygen) as independent variables. The syngas derived from gasification was analyzed by two chromatographic techniques, which reported the presence of refinery gases and sulfur. We evidenced a growth tendency of CO, H 2 and sulfur composition and a decrease in CH 4 and CO 2 composition with temperature. The composition of the syngas was evaluated with different quantities of gasification agent (33%, 40% and 47% the amount of oxygen theoretically required for complete combustion) at each temperature levels operated. It was established that when using a 40% of gasification agent, you get greater average content of CO and H 2 , which are the interest gases in the gasification process.

Syngas obtainment from the gasification of asphaltenes of the San Fernando crude oil

International Nuclear Information System (INIS)

Moreno Arciniegas, Laura Smith; Rodriguez Corredor, Fabio Ernesto; Afanador Rey, Luz Edelmira; Grosso Vargas, Jorge Luis

2009-01-01

In this work, we developed the first study in Colombia to obtain and evaluate syngas compositions derived from asphaltenes gasification. These asphaltenes came from the implementation of a Deasphalting process to San Fernando crude oil, with the purpose of looking for technological options for their utilization. We performed the design, installation and commissioning of facilities for the gasification of asphaltenes at laboratory scale, it following an experimental methodology, performing nine tests and considering temperature and agent gasification quantity (oxygen) as independent variables. The syngas derived from gasification was analyzed by two chromatographic techniques, which reported the presence of refinery gases and sulfur. We evidenced a growth tendency of CO, H 2 and sulfur composition and a decrease in CH 4 and CO 2 composition with temperature. The composition of the syngas was evaluated with different quantities of gasification agent (33%, 40% and 47% the amount of oxygen theoretically required for complete combustion) at each temperature levels operated. It was established that when using a 40% of gasification agent, you get greater average content of CO and H 2 , which are the interest gases in the gasification process.

Comparisons Between Asphaltenes from the Dead and Live-Oil Samples of the Same Crude Oils

DEFF Research Database (Denmark)

Aquino-Olivos, M.A.; Andersen, Simon Ivar; Lira-Galeana, C.

2003-01-01

extracted and analyzed. These pressure-driven asphaltenes found on the filter were found to make up in the range between 50 and 100 ppm of the whole crude oil. Opening of the cell did not reveal asphaltenes retained due to wall adhesion. Size exclusion chromatography tests performed on both the live......-oil-derived asphaltenes and the standard asphaltenes as precipitated by atmospheric titration on the same crude oil, revealed that the live-oil asphaltenes had apparent smaller hydrodynamic volume and narrower distributions than the standard asphaltenes for two oils. Further FTIR tests also showed large differences...

Comparison between asphaltenes fractions extracted from different asphaltic residue; Comparacao de fracoes de asfaltenos obtidas a partir de residuos asfalticos distintos

Energy Technology Data Exchange (ETDEWEB)

Barreira, Fabio R.; Lucas, Elizabete F., E-mail: fabiorbarreira@yahoo.com.br [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil); Ferreira, Silas R. [Clariant S/A, Rio de Janeiro, RJ (brazil)

2015-07-01

Asphaltenes are blamed for various problems in the petroleum industry, especially formation of solid deposits and stabilization of water-in-oil emulsions. Due to the diversity and complexity of these structures, there is still much to be investigated in terms of characterization and stability. In this study, asphaltene subfractions were extracted from an asphaltic residue (AR02), characterized by nuclear magnetic resonance (NMR), elemental analysis (CHN), X-ray fluorescence and time-of-flight mass spectrometry (MS-TOF), and compared to previous results obtained for another asphaltic residue. The precipitation onset of (sub)fractions was assessed by optical microscopy. The results obtained indicate there are more differences than similarities between the asphaltene fractions obtained from the asphaltic residues of distinct origins, with respect to aromaticity, elemental composition (CHN), presence and content of hetero elements and average molar mass. On the matter of stability, it seems that small differences in molecules polarity provoke great differences on phase behavior of every isolated asphaltenes fractions. (author)

Using the fluorescence of DBO to study the aggregation of asphaltenes

Energy Technology Data Exchange (ETDEWEB)

Yang, Zixin; Bohne, Cornelia [Department of Chemistry, University of Victoria (Canada)], email: xyang@uvic.ca

2010-07-01

Asphaltene, operationally defined as the fraction of bitumen that is insoluble in heptane but soluble in toluene, is the least characterized component of crude oil. It can aggregate at low concentrations, causing problems in the reservoir and during transport and processing. Fluorescence techniques have been employed to characterize asphaltenes, e.g. by adding external probes. DBO (2,3-diazabicyclo [2.2.2]oct-2-ene), a fluorescence probe molecule with a long fluorescence lifetime, was made sensitive to the presence of aliphatic C-H bonds. DBO was used as an external fluorescent probe to characterize the aggregation of Athabasca asphaltene. The lifetime of DBO was measured using single photon counting. Preliminary lifetime measurements show that AA-5 quenches the emission of DBO, leading to a shortening of the DBO lifetime. The abrupt decrease in lifetime may be related to the interaction of DBO with the AA-5 aggregate; further studies are being performed to test this hypothesis. In conclusion, DBO interacts with asphaltene components and has the potential for being used as a probe to study the asphaltene aggregation.

Effect on molecular interactions of chemical alteration of petroleum asphaltenes. I

DEFF Research Database (Denmark)

Juyal, Priyanka; Garcia, Daniel Merino; Andersen, Simon Ivar

2005-01-01

Asphaltenes are naturally occurring components of crude oil and have been the subject of many studies that have involved a variety of methods to determine their complex structure, their association in crude oil with resins, and their agglomeration phenomena. Yet, the molecular structures of aspha......Asphaltenes are naturally occurring components of crude oil and have been the subject of many studies that have involved a variety of methods to determine their complex structure, their association in crude oil with resins, and their agglomeration phenomena. Yet, the molecular structures...... of asphaltenes have not been fully elucidated. It is especially important to characterize the polar functionalities of these fractions, because they participate in the intermolecular aggregation by means of hydrogen bonds. The chemical derivatization of asphaltenes has been used, in combination with suitable...

Experimental Study and Mathematical Modeling of Asphaltene Deposition Mechanism in Core Samples

Directory of Open Access Journals (Sweden)

Jafari Behbahani T.

2015-11-01

Full Text Available In this work, experimental studies were conducted to determine the effect of asphaltene deposition on the permeability reduction and porosity reduction of carbonate, sandstone and dolomite rock samples using an Iranian bottom hole live oil sample which is close to reservoir conditions, whereas in the majority of previous work, a mixture of recombined oil (a mixture of dead oil and associated gas was injected into a core sample which is far from reservoir conditions. The effect of the oil injection rate on asphaltene deposition and permeability reduction was studied. The experimental results showed that an increase in the oil injection flow rate can result in an increase in asphaltene deposition and permeability reduction. Also, it can be observed that at lower injection flow rates, a monotonic decrease in permeability of the rock samples can be attained upon increasing the injection flow rate, while at higher injection rates, after a decrease in rock permeability, an increasing trend is observed before a steady-state condition can be reached. The experimental results also showed that the rock type can affect the amount of asphaltene deposition, and the asphaltene deposition has different mechanisms in sandstone and carbonate core samples. It can be seen that the adsorption and plugging mechanisms have a more important role in asphaltene deposition in carbonate core samples than sandstone core samples. From the results, it can be observed that the pore volumes of the injected crude oil are higher for sandstone cores compared with the carbonate cores. Also, it can be inferred that three depositional types may take place during the crude oil injection, i.e., continuous deposition for low-permeability cores, slow, steady plugging for high-permeability cores and steady deposition for medium-permeability cores. It can be seen from the experimental results that damage to the core samples was found to increase when the production pressures were

Colloidal Asphaltene Deposition and Aggregation in Capillary Flow: Experiments and Mesoscopic Simulation

Science.gov (United States)

Boek, Edo S.; Ladva, Hemant K.; Crawshaw, John P.; Padding, Johan T.

2008-07-01

The aggregation and deposition of colloidal asphaltene in reservoir rock is a significant problem in the oil industry. To obtain a fundamental understanding of this phenomenon, we have studied the deposition and aggregation of colloidal asphaltene in capillary flow by experiment and simulation. For the simulation, we have used the stochastic rotation dynamics (SRD) method, in which the solvent hydrodynamic emerges from the collisions between the solvent particles, while the Brownian motion emerges naturally from the interactions between the colloidal asphaltene particles and the solvent. The asphaltene colloids interact through a screened Coulomb potential. We vary the well depth ɛ∝ and the flow rate v to obtain Peflow≫1 (hydrodynamic interactions dominate) and Re≪1 (Stokes flow). In the simulations, we impose a pressure drop over the capillary length and measure the corresponding solvent flow rate. We observe that the transient solvent flow rate decreases when the asphaltene particles become more "sticky". For a well depth ɛ∝ = 2kBT, a monolayer deposits on the capillary wall. With an increasing well depth, the capillary becomes totally blocked. The clogging is transient for ɛ∝ = 5kBT, but appears to be permanent for ɛ∝ = 10-20 kBT. We compare our simulation results with flow experiments in glass capillaries, where we use extracted asphaltenes in toluene, reprecipitated with n-heptane. In the experiments, the dynamics of asphaltene precipitation and deposition were monitored in a slot capillary using optical microscopy under flow conditions similar to those used in the simulation. Maintaining a constant flow rate of 5 μL min-1, we found that the pressure drop across the capillary first increased slowly, followed by a sharp increase, corresponding to a complete local blockage of the capillary. Doubling the flow rate to 10 μL min-1, we observe that the initial deposition occurs faster but the deposits are subsequently entrained by the flow. We

Chemical modification of cobalt ferrite nanoparticles with possible application as asphaltene flocculant agent

Energy Technology Data Exchange (ETDEWEB)

Oliveira, G.E.; Clarindo, J.E.S.; Santo, K.S.E., E-mail: geiza.oliveira@ufes.br [Universidade Federal do Espirito Santo (CCE/DQUI/UFES), Vitoria, ES (Brazil). Centro de Ciencias Exatas. Dept. de Quimica; Souza Junior, F.G. [Universidade Federal do Rio de Janeiro (IMA/UFRJ), Rio de Janeiro, RJ (Brazil). Instituto de Macromoleculas

2013-11-01

Asphaltenes can cause enormous losses in the oil industry, because they are soluble only in aromatic solvents. Therefore, they must be removed from the petroleum before it is refined, using flocculant agents. Aiming to find new materials that can work as flocculant agents to asphaltenes, cobalt ferrite nanoparticles were chemically modified through acid-base reactions using dodecylbenzene sulfonic acid (DBSA) to increase their lipophilicity. Nanoparticle synthesis was performed using the co-precipitation method followed by annealing of these nanoparticles, aiming to change the structural phase. Modified and unmodified nanoparticles were tested by FTIR-ATR, XRD and TGA/DTA. In addition, precipitation onset of the asphaltenes was performed using modified and unmodified nanoparticles. These tests showed that modified nanoparticles have a potential application as flocculant agents used to remove asphaltenes before oil refining, since the presence of nanoparticles promotes the asphaltene precipitation onset with the addition of a small amount of non-solvent (author)

Chemical modification of cobalt ferrite nanoparticles with possible application as asphaltene flocculant agent

International Nuclear Information System (INIS)

Oliveira, G.E.; Clarindo, J.E.S.; Santo, K.S.E.; Souza Junior, F.G.

2013-01-01

Asphaltenes can cause enormous losses in the oil industry, because they are soluble only in aromatic solvents. Therefore, they must be removed from the petroleum before it is refined, using flocculant agents. Aiming to find new materials that can work as flocculant agents to asphaltenes, cobalt ferrite nanoparticles were chemically modified through acid-base reactions using dodecylbenzene sulfonic acid (DBSA) to increase their lipophilicity. Nanoparticle synthesis was performed using the co-precipitation method followed by annealing of these nanoparticles, aiming to change the structural phase. Modified and unmodified nanoparticles were tested by FTIR-ATR, XRD and TGA/DTA. In addition, precipitation onset of the asphaltenes was performed using modified and unmodified nanoparticles. These tests showed that modified nanoparticles have a potential application as flocculant agents used to remove asphaltenes before oil refining, since the presence of nanoparticles promotes the asphaltene precipitation onset with the addition of a small amount of non-solvent (author)

Study of asphaltene precipitation by Calorimetry

DEFF Research Database (Denmark)

Verdier, Sylvain Charles Roland; Plantier, Frédéric; Bessières, David

2007-01-01

Can calorimetry bring new input to the Current understanding of asphaltene precipitation? In this work, two types of precipitation were studied by means of calorimetry: addition of n-heptane into asphaltene solutions and temperature/pressure variations on a recombined live oil. The first series...... of experiments showed that weak forces determine precipitation. Indeed, isothermal titration calorimetry could not detect any clear signal although this technique can detect low-energy transitions such as liquid-liquid equilibrium and rnicellization. The second series of tests proved that precipitation caused...... by T and P variations is exothermic for this system. Furthermore, the temperature-induced precipitation is accompanied by an increase in the apparent thermal expansivity. Therefore, it seems that these two phase transitions exhibit different calorimetric behaviours and they may not be as similar...

Mesoscale Simulation and Machine Learning of Asphaltene Aggregation Phase Behavior and Molecular Assembly Landscapes.

Science.gov (United States)

Wang, Jiang; Gayatri, Mohit A; Ferguson, Andrew L

2017-05-11

Asphaltenes constitute the heaviest fraction of the aromatic group in crude oil. Aggregation and precipitation of asphaltenes during petroleum processing costs the petroleum industry billions of dollars each year due to downtime and production inefficiencies. Asphaltene aggregation proceeds via a hierarchical self-assembly process that is well-described by the Yen-Mullins model. Nevertheless, the microscopic details of the emergent cluster morphologies and their relative stability under different processing conditions remain poorly understood. We perform coarse-grained molecular dynamics simulations of a prototypical asphaltene molecule to establish a phase diagram mapping the self-assembled morphologies as a function of temperature, pressure, and n-heptane:toluene solvent ratio informing how to control asphaltene aggregation by regulating external processing conditions. We then combine our simulations with graph matching and nonlinear manifold learning to determine low-dimensional free energy surfaces governing asphaltene self-assembly. In doing so, we introduce a variant of diffusion maps designed to handle data sets with large local density variations, and report the first application of many-body diffusion maps to molecular self-assembly to recover a pseudo-1D free energy landscape. Increasing pressure only weakly affects the landscape, serving only to destabilize the largest aggregates. Increasing temperature and toluene solvent fraction stabilizes small cluster sizes and loose bonding arrangements. Although the underlying molecular mechanisms differ, the strikingly similar effect of these variables on the free energy landscape suggests that toluene acts upon asphaltene self-assembly as an effective temperature.

An experimental study of asphaltene particle sizes in n-heptane-toluene mixtures by light scattering

Directory of Open Access Journals (Sweden)

Rajagopal K.

2004-01-01

Full Text Available The particle size of asphaltene flocculates has been the subject of many recent studies because of its importance in the control of deposition in petroleum production and processing. We measured the size of asphaltene flocculates in toluene and toluene - n-heptane mixtures, using the light-scattering technique. The asphaltenes had been extracted from Brazilian oil from the Campos Basin, according to British Standards Method IP-143/82. The asphaltene concentration in solution ranged between 10-6 g/ml and 10-7 g/ml. Sizes was measured for a period of about 10000 minutes at a constant temperature of 20°C. We found that the average size of the particles remained constant with time and increase with an increase in amount of n-heptane. The correlation obtained for size with concentration will be useful in asphaltene precipitation models.

Asphaltene self-association: Modeling and effect of fractionation with a polar solvent

DEFF Research Database (Denmark)

Garcia, Daniel Merino; Murgich, J; Andersen, Simon Ivar

2004-01-01

of DeltaH(a) obtained suggest that a fraction of asphaltenes is not active in the calorimetric experiments. Asphaltenes from Venezuela (LM1) and Mexico (KU) have been fractionated by precipitation with a mixture of acetone and toluene. It is considered that the most polar compounds are collected...

Molecular Dynamics Simulation: The Behavior of Asphaltene in Crude Oil and at the Oil/Water Interface

KAUST Repository

Gao, Fengfeng

2014-12-18

Carboxyl asphaltene is commonly discussed in the petroleum industry. In most conditions, electroneutral carboxyl asphaltene molecules can be deprotonated to become carboxylate asphaltenes. Both in crude oil and at the oil/water interface, the characteristics of anionic carboxylate asphaltenes are different than those of the carboxyl asphaltenes. In this paper, molecular dynamics (MD) simulations are utilized to study the structural features of different asphaltene molecules, namely, C5 Pe and anionic C5 Pe, at the molecular level. In crude oil, the electroneutral C5 Pe molecules prefer to form a steady face-to-face stacking, while the anionic C5 Pe molecules are inclined to form face-to-face stacking and T-shaped II stacking because of the repulsion of the anionic headgroups. Anionic C5 Pe has a distinct affinity to the oil/water interface during the simulation, while the C5 Pe molecules persist in the crude oil domain. A three-stage model of anionic C5 Pe molecules adsorbed at the oil/water interface is finally developed.

Synthesis and characterization of the polystyrene - asphaltene graft copolymer BY FT-IR spectroscopy

International Nuclear Information System (INIS)

Leo, Adan Yovani; Salazar Ramiro

2008-01-01

The creation of new polymer compounds to be added to asphalt has drawn considerable attention because these substances have succeeded in modifying the asphalt rheological characteristics and physical properties for the enhancement of its behavior during the time of use. This work explains the synthesis of a new graft copolymer based on an asphalt fraction called asphaltene, modified with maleic anhydride. Polystyrene functionalization is conducted in a parallel fashion in order to obtain polybenzylamine resin with an amine - NH2 free group that reacts with the anhydride graft groups in the asphaltene, thus obtaining the new Polystyrene/Asphaltene graft copolymer

Asphaltene precipitation and its effects on the vapour extraction (VAPEX) heavy oil recovery process

Energy Technology Data Exchange (ETDEWEB)

Luo, P.; Wang, X.; Gu, Y. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Regina Univ., SK (Canada). Petroleum Technology Research Centre; Zhang, H. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Core Laboratories Canada Ltd., Calgary, AB (Canada); Moghadam, L. [Fekete Associates Inc., Calgary, AB (Canada)

2008-10-15

One of the most important physical phenomena during the solvent vapour extraction (VAPEX) of heavy oil recovery is asphaltene precipitation. After the asphaltene precipitation occurs, the produced heavy oil is deasphalted in-situ, resulting in a lower viscosity and better quality. However, precipitated asphaltenes may plug some small pores of the reservoir formation, thus reducing its permeability. This paper examined the effects of three operating factors on the asphaltene precipitation during the VAPEX process, notably solvent type; operating pressure; and sand-pack permeability. Eight VAPEX tests were conducted to recover two different Lloydminster heavy oil samples from a rectangular sand-packed physical model with a butane mixture and propane as the respective solvents. The accumulative heavy oil and solvent production from the physical model were measured in the entire VAPEX process. The paper described the materials, experimental set-up, and experimental preparation. The VAPEX test was also explained. Results were presented for sand consolidation; solvent effect; pressure effect; and permeability effect. It was concluded that when the extracting solvent is in a liquid-gas state, asphaltene precipitation occurs and leads to in-situ deasphalting. 15 refs., 3 tabs., 6 figs.

Developing grey-box model to diagnose asphaltene stability in crude oils: Application of refractive index

Directory of Open Access Journals (Sweden)

Mahdi Zeinali Hasanvand

2016-12-01

Full Text Available Asphaltene precipitation can cause serious problems in petroleum industry while diagnosing the asphaltene stability conditions in crude oil system is still a challenge and has been subject of many investigations. To monitor and diagnose asphaltene stability, high performance intelligent approaches based bio-inspired science like artificial neural network which have been optimized by various optimization techniques have been carried out. The main purpose of the implemented optimization algorithms is to decide high accurate interconnected weights of proposed neural network model. The proposed intelligent approaches are examined by using extensive experimental data reported in open literature. Moreover, to highlight robustness and precision of the addressed approaches, two different regression models have been developed and results obtained from the aforementioned intelligent models and regression approaches are compared with the corresponding refractive index data measured in laboratory. Based on the results, hybrid of genetic algorithm and particle swarm optimization have high performance and average relative absolute deviation between the model outputs and the relevant experimental data was found to be less than 0.2%. Routs from this work indicate that implication of HGAPSO-ANN in monitoring refractive index can lead to more reliable estimation of addressed issue which can lead to design of more reliable phase behavior simulation and further plans of oil production.

Rheological properties of hydrate suspensions in asphaltenic crude oils; Proprietes rheologiques de suspensions d'hydrate dans des bruts asphalteniques

Energy Technology Data Exchange (ETDEWEB)

Marques de Toledo Camargo, R.

2001-03-01

The development of offshore oil exploitation under increasing water depths has forced oil companies to increase their understanding of gas hydrate formation and transportation in multiphase flow lines in which a liquid hydrocarbon phase is present. This work deals with the flow behaviour of hydrate suspensions in which a liquid hydrocarbon is the continuous phase. Three different liquid hydrocarbons are used: an asphaltenic crude oil, a condensate completely free of asphaltenes and a mixture between the asphaltenic oil and heptane. The rheological characterisation of hydrate suspensions is the main tool employed. Two original experimental devices are used: a PVT cell adapted to operate as a Couette type rheometer and a semi-industrial flow loop. Hydrate suspensions using the asphaltenic oil showed shear-thinning behaviour and thixotropy. This behaviour is typically found in flocculated systems, in which the particles attract each other forming flocs of aggregated particles at low shear rates. The suspensions using the condensate showed Newtonian behaviour. Their relative viscosities were high, which suggests that an aggregation process between hydrate particles takes. place during hydrate formation. Finally, hydrate suspensions using the mixture asphaltenic oil-heptane showed shear-thinning behaviour, thixotropy and high relative viscosity. From these results it can be inferred that, after the achievement of the hydrate formation process, the attractive forces between hydrate particles are weak. making unlikely pipeline obstruction by an aggregation process. Nevertheless, during the hydrate formation, these attractive forces can be sufficiently high. It seems that the hydrate surface wettability is an important parameter in this phenomena. (author)

Molecular Dynamics Simulation to Investigate the Interaction of Asphaltene and Oxide in Aggregate

Directory of Open Access Journals (Sweden)

Rui Li

2016-01-01

Full Text Available The asphalt-aggregate interface interaction (AAI plays a significant role in the overall performances of asphalt mixture, which is caused due to the complicated physicochemical processes and is influenced by various factors, including the acid-base property of aggregates. In order to analyze the effects of the chemical constitution of aggregate on the AAI, the average structure C65H74N2S2 is selected to represent the asphaltene in asphalt and magnesium oxide (MgO, calcium oxide (CaO, aluminium sesquioxide (Al2O3, and silicon dioxide (SiO2 are selected to represent the major oxides in aggregate. The molecular models are established for asphaltene and the four oxides, respectively, and the molecular dynamics (MD simulation was conducted for the four kinds of asphaltene-oxide system at different temperatures. The interfacial energy in MD simulation is calculated to evaluate the AAI, and higher value means better interaction. The results show that interfacial energy between asphaltene and oxide reaches the maximum value at 25°C and 80°C and the minimum value at 40°C. In addition, the interfacial energy between asphaltene and MgO was found to be the greatest, followed by CaO, Al2O3, and SiO2, which demonstrates that the AAI between asphalt and alkaline aggregates is better than acidic aggregates.

Calorimetric Evidence about the Application of the Concept of CMC to Asphaltene Self-Association

DEFF Research Database (Denmark)

Garcia, Daniel Merino; Andersen, Simon Ivar

2005-01-01

that asphaltenes may also have a concentration at which self-association occurs (CMC). This article presents evidence found by calorimetry and spectroscopic techniques, that suggest that this concept may not be adequate for asphaltene self-association in toluene solutions. Isothermal titration calorimetry has been...

Diagnosis of asphaltene stability in crude oil through “two parameters” SVM model

DEFF Research Database (Denmark)

Chamkalani, Ali; Mohammadi, Amir H.; Eslamimanesh, Ali

2012-01-01

Asphaltene precipitation/deposition and its imposing difficulties are drastic issues in petroleum industry. Monitoring the asphaltene stability conditions in crude oil systems is still a challenge and has been subject of many studies. In this work, the Refractive Index (RI) of several oil samples...... and previously-presented empirical correlations available in open literature. © 2012 Elsevier Ltd....

Chemistry and structure of coal-derived asphaltenes, Phase III. Quarterly progress report, April--June 1978

Energy Technology Data Exchange (ETDEWEB)

Yen, T. F.

1978-01-01

Solubility parameters may be calculated for coal liquid derived products by use of a semi-empirical relationship between solubility parameter and refractive index. Thermal treatment of Synthoil coal liquid oil + resin solvent fraction at 235 to 300/sup 0/C resulted in the transformation of oil and resin into asphaltene. Further support of structural characterizations was obtained by use of a combined x-ray and NMR structural characterization procedure which relies on the important x-ray structural parameter L/sub a/ (average layer diameter of the aromatic sheet). L/sub a/ values of approx. = 8 to 10 A for asphaltenes, approx. = 13.4 to 14 A for carbenes, and approx. = 14 to 16.5 A for carboids were obtained by the x-ray procedure. These data were used to calculate C/sub Au/ (aromatic carbons per structural unit) and N (number of structural units per molecule) values. For asphaltenes the results agree with those previously deduced from NMR and other techniques. The C/sub Au/ values are generally close to 14 which is the number of aromatic carbons present in a 3-ring kata-system such as anthracene or phenanthrene. The number of structural units per molecule is close to two for all the asphaltenes. Additional data were used to improve the correlation equation between weight percent OH, determined by the silylation method, and the absorbance of the monomeric OH infrared stretching band at 3600 cm/sup -1/ for asphaltenes. A similar correlation between weight percent NH, from elemental analysis of asphaltene samples containing essentially all nitrogen as pyrrolic N-H, and the infrared absorbance of the N-H stretching band at 3470 cm/sup -1/ was developed for asphaltenes.

A Thermodynamic Mixed-Solid Asphaltene Precipitation Model

DEFF Research Database (Denmark)

Lindeloff, Niels; Heidemann, R.A.; Andersen, Simon Ivar

1998-01-01

A simple model for the prediction of asphaltene precipitation is proposed. The model is based on an equation of state and uses standard thermodynamics, thus assuming that the precipitation phenomenon is a reversible process. The solid phase is treated as an ideal multicomponent mixture. An activity...

Asphaltene based photovoltaic devices

Science.gov (United States)

Chianelli, Russell R.; Castillo, Karina; Gupta, Vipin; Qudah, Ali M.; Torres, Brenda; Abujnah, Rajib E.

2016-03-22

Photovoltaic devices and methods of making the same, are disclosed herein. The cell comprises a photovoltaic device that comprises a first electrically conductive layer comprising a photo-sensitized electrode; at least one photoelectrochemical layer comprising metal-oxide particles, an electrolyte solution comprising at least one asphaltene fraction, wherein the metal-oxide particles are optionally dispersed in a surfactant; and a second electrically conductive layer comprising a counter-electrode, wherein the second electrically conductive layer comprises one or more conductive elements comprising carbon, graphite, soot, carbon allotropes or any combinations thereof.

Molecular mechanics and microcalorimetric investigations of the effects of molecular water on the aggregation of asphaltenes in solutions

DEFF Research Database (Denmark)

Murgich, J.; Lira-Galeana, C.; Garcia, Daniel Merino

2002-01-01

The interaction of two model asphaltene molecules from the Athabasca sand oil with a water molecule in a toluene solution was studied by means of molecular mechanics calculations. It was found that water forms bridging H bonds between the heteroatoms of asphaltenes with a considerable span...... in energies. The stronger H bond found has energies higher than those corresponding to the stacking of the aromatic areas of the same asphaltene molecules. This shows that the water molecule may generate additional mechanisms of aggregation of asphaltenes in toluene solution, as found experimentally. The H...... by titration calorimetry. A simple dimer dissociation model was used to derive the information about the heat and the constant of dissociation from asphaltenes of Mexico and Alaska obtained from the calorimetric data. The association enthalpies calculated were found to be in excellent agreement with those...

Chemistry and structure of coal derived asphaltenes and preasphaltenes. Quarterly progress report, April-June 1980

Energy Technology Data Exchange (ETDEWEB)

Yen, T. F.

1980-01-01

It is the objective of this project to isolate the asphaltene and preasphaltene fractions from coal liquids from a number of liquefaction processes. These processes consist of in general: catalytic hydrogenation, staged pyrolysis and solvent refining. These asphaltene fractions may be further separated by both gradient elution through column chromatography, and molecular size distribution through gel permeation chromatography. Those coal-derived asphaltene and preasphaltene fractions will be investigated by various chemical and physical methods for characterization of their structures. After the parameters are obtained, these parameters will be correlated with the refining and conversion variables which control a given type of liquefaction process. The effects of asphaltene in catalysis, ash or metal removal, desulfurization and denitrification will also be correlated. It is anticipated that understanding the role of asphaltenes in liquefaction processes will enable engineers to both improve existing processes, and to make recommendations for operational changes in planned liquefaction units in the United States. The objective of Phase 1 was to complete the isolation and separation of coal liquid fractions and to initiate their characterization. The objective of Phase 2 is to continue the characterization of coal asphaltenes and other coal liquid fractions by use of physical and instrumental methods. The structural parameters obtained will be used to postulate hypothetical average structures for coal liquid fractions. The objective of Phase 3 is to concentrate on the characterization of the preasphaltene (benzene insoluble fraction) of coal liquid fraction by the available physical and chemical methods to obtain a number of structural parameters.

Modeling of Asphaltene Precipitation from Crude Oil with the Cubic Plus Association Equation of State

DEFF Research Database (Denmark)

Arya, Alay; Liang, Xiaodong; von Solms, Nicolas

2017-01-01

In this study, different modeling approaches using the Cubic Plus Association (CPA) equation of state (EoS) are developed to calculate the asphaltene precipitation onset condition and asphaltene yield from degassed crude oil during the addition of n-paraffin. A single model parameter is fitted...

Asphaltene-laden interfaces form soft glassy layers in contraction experiments: a mechanism for coalescence blocking.

Science.gov (United States)

Pauchard, Vincent; Rane, Jayant P; Banerjee, Sanjoy

2014-11-04

In previous studies, the adsorption kinetics of asphaltenes at the water-oil interface were interpreted utilizing a Langmuir equation of state (EOS) based on droplet expansion experiments.1-3 Long-term adsorption kinetics followed random sequential adsorption (RSA) theory predictions, asymptotically reaching ∼85% limiting surface coverage, which is similar to limiting random 2D close packing of disks. To extend this work beyond this slow adsorption process, we performed rapid contractions and contraction-expansions of asphaltene-laden interfaces using the pendant drop experiment to emulate a Langmuir trough. This simulates the rapid increase in interfacial asphaltene concentration that occurs during coalescence events. For the contraction of droplets aged in asphaltene solutions, deviation from the EOS consistently occurs at a surface pressure value ∼21 mN/m corresponding to a surface coverage ∼80%. At this point droplets lose the shape required for validity of the Laplace-Young equation, indicating solidlike surface behavior. On further contraction wrinkles appear, which disappear when the droplet is held at constant volume. Surface pressure also decreases down to an equilibrium value near that measured for slow adsorption experiments. This behavior appears to be due to a transition to a glassy interface on contraction past the packing limit, followed by relaxation toward equilibrium by desorption at constant volume. This hypothesis is supported by cycling experiments around the close-packed limit where the transition to and from a solidlike state appears to be both fast and reversible, with little hysteresis. Also, the soft glass rheology model of Sollich is shown to capture previously reported shear behavior during adsorption. The results suggest that the mechanism by which asphaltenes stabilize water-in-oil emulsions is by blocking coalescence due to rapid formation of a glassy interface, in turn caused by interfacial asphaltenes rapidly increasing in

The influence of petroleum asphaltenic sub fractions on the demulsifiers performance; Influencia de subfracoes asfaltenicas de petroleo sobre a acao de desemulsificantes

Energy Technology Data Exchange (ETDEWEB)

Honse, Siller O.; Mansur, Claudia R.E.; Lucas, Elizabete F. [Universidade Federal do Rio de Janeiro (IMA/UFRJ), RJ (Brazil). Inst. de Macromoleculas. Lab. de Macromoleculas e Coloides na Industria de Petroleo], e-mail: celias@ima.ufrj.br

2011-07-01

The aim of this work is to evaluate the influence of asphaltene fractions and subfractions on the stabilization of petroleum emulsions, as well as on the efficiency of demulsifiers based on poly(ethylene oxide-b-propylene oxide) (PEO-PPO). Asphaltenes were extracted from an asphaltic residue using n-heptane (C5 asphaltenes) and n-decane (asphaltenes C10). Intermediate subfractions were also obtained. Model emulsions, consisted of water and dispersions of the asphaltene in toluene were prepared, with and without adding demulsifier. The stability of the emulsions was higher when adding more polar fractions. However, asphaltenes presenting a broad distribution of polarity cause higher emulsion stability than that presenting very narrow distribution of intermediate polarity. The efficiency of PEO-PPO copolymer on emulsions separation is related to the original stability of the emulsions. In this work, it was confirmed that branched surfactant presents higher efficiency than the linear. (author)

Influence of containing of asphaltenes and naphthenic acids over organic deposition inhibitor performance

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Geiza E.; Mansur, Claudia R.E.; Pires, Renata V.; Passos, Leonardo B.; Lucas, Elizabete F. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Inst. de Macromoleculas; Alvares, Dellyo R.S.; Gonzalez, Gaspar [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES)

2004-07-01

Organic deposition is a serious problem confronted by the petroleum industry in Brazil and worldwide. Among the main petroleum components that may cause deposition problems are waxes and asphaltenes. This work aims at evaluating the influence of petroleum fractions (asphaltenes and naphthenic acids) on the organic deposition phenomenon as well as on organic deposition inhibitors performance. The influence of the organic fractions was evaluated by their ability to change wax crystals, to lower the pour point and to alter the initial wax appearance temperature. The efficiency of the additives was tested by pour point measurements. The results show that asphaltenes seem to act as organic deposition inhibitors, while naphthenic acids do not significantly change the system. Moreover, employing both of them produces no synergic effect. Among polymeric inhibitors, all of the chemically modified EVA copolymer presented better results than the non-modified commercial EVA copolymer. The best result was observed for EVA28C{sub 16}. (author)

Investigation of the Gas Injection Effect on Asphaltene Onset Precipitation Using the Cubic-Plus-Association Equation of State

DEFF Research Database (Denmark)

Arya, Alay; von Solms, Nicolas; Kontogeorgis, Georgios M.

2016-01-01

Miscible and immiscible gas flooding is one of the enhanced oil recovery (EOR) techniques that has been widely used to increase the oil production. One of the critical problems with gas flooding is that it generally aggravates the asphaltene precipitation, which further creates a flow assurance...... dependency upon the saturates, aromatics, resins, and asphaltenes (SARA) analysis or molecular weight (MW) of asphaltene is also analyzed. In addition, a unique characteristic of the model for the given stock tank oil (STO) is identified, which does not change with different types and amounts of gas...... injections and also remains the same at upper and lower onset pressure boundaries. On the basis of this unique characteristic, a simple procedure to predict asphaltene phase envelope (APE) for the reservoir oil with relatively simple and few experimental data, performed on STO with n...

Asphaltenes in Mexican fuel oils; Asfaltenos en combustoleos mexicanos

Energy Technology Data Exchange (ETDEWEB)

Longoria Ramirez, Rigoberto [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1996-12-31

In this article the main aspects in which the Instituto de Investigaciones Electricas (IIE) has worked to contribute to the solution of problems due to the presence of asphaltenes in national fuel oils, are emphasized. The increment of these compounds, that concentrate harmful elements, in the last ten years has reached 22% by weight of the fuel oil. It is demonstrated that the quantification of asphaltenes depends on the type of solvent employed. [Espanol] En este articulo se subrayan los principales aspectos en los que el Instituto de Investigaciones Electricas (IIE) ha trabajado para contribuir a la solucion de problemas debidos a la presencia de asfaltenos en combustoleos nacionales. El incremento de estos compuestos, que concentran elementos nocivos, en los ultimos diez anos ha llegado hasta un 22% del peso del combustoleo. Se demuestra que la cuantificacion de los asfaltenos depende del tipo de solvente utilizado.

Asphaltenes in Mexican fuel oils; Asfaltenos en combustoleos mexicanos

Energy Technology Data Exchange (ETDEWEB)

Longoria Ramirez, Rigoberto [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1997-12-31

In this article the main aspects in which the Instituto de Investigaciones Electricas (IIE) has worked to contribute to the solution of problems due to the presence of asphaltenes in national fuel oils, are emphasized. The increment of these compounds, that concentrate harmful elements, in the last ten years has reached 22% by weight of the fuel oil. It is demonstrated that the quantification of asphaltenes depends on the type of solvent employed. [Espanol] En este articulo se subrayan los principales aspectos en los que el Instituto de Investigaciones Electricas (IIE) ha trabajado para contribuir a la solucion de problemas debidos a la presencia de asfaltenos en combustoleos nacionales. El incremento de estos compuestos, que concentran elementos nocivos, en los ultimos diez anos ha llegado hasta un 22% del peso del combustoleo. Se demuestra que la cuantificacion de los asfaltenos depende del tipo de solvente utilizado.

Interfacial rheology of asphaltenes at oil-water interfaces and interpretation of the equation of state.

Science.gov (United States)

Rane, Jayant P; Pauchard, Vincent; Couzis, Alexander; Banerjee, Sanjoy

2013-04-16

In an earlier study, oil-water interfacial tension was measured by the pendant drop technique for a range of oil-phase asphaltene concentrations and viscosities. The interfacial tension was found to be related to the relative surface coverage during droplet expansion. The relationship was independent of aging time and bulk asphaltenes concentration, suggesting that cross-linking did not occur at the interface and that only asphaltene monomers were adsorbed. The present study extends this work to measurements of interfacial rheology with the same fluids. Dilatation moduli have been measured using the pulsating droplet technique at different frequencies, different concentrations (below and above CNAC), and different aging times. Care was taken to apply the technique in conditions where viscous and inertial effects are small. The elastic modulus increases with frequency and then plateaus to an asymptotic value. The asymptotic or instantaneous elasticity has been plotted against the interfacial tension, indicating the existence of a unique relationship, between them, independent of adsorption conditions. The relationship between interfacial tension and surface coverage is analyzed with a Langmuir equation of state. The equation of state also enabled the prediction of the observed relationship between the instantaneous elasticity and interfacial tension. The fit by a simple Langmuir equation of state (EOS) suggests minimal effects of aging and of nanoaggregates or gel formation at the interface. Only one parameter is involved in the fit, which is the surface excess coverage Γ∞ = 3.2 molecules/nm(2) (31.25 Å(2)/molecule). This value appears to agree with flat-on adsorption of monomeric asphaltene structures consisting of aromatic cores composed of an average of six fused rings and supports the hypothesis that nanoaggregates do not adsorb on the interface. The observed interfacial effects of the adsorbed asphaltenes, correlated by the Langmuir EOS, are consistent with

Use of compound-specific stable carbon isotope ratio measurements of asphaltene-bound polycyclic aromatic hydrocarbons (PAHs) as a novel aid to source apportionment of environmental PAHs

Energy Technology Data Exchange (ETDEWEB)

C. Sun; C. Snape; M. Cooper; W. Ivwurie [University of Nottingham, Nottingham (United Kingdom). Nottingham Energy & Fuel Centre

2005-07-01

In this study, the PAHs from hydropyrolysis of asphaltenes from different primary sources (e.g. crude oil, low and high temperature coal tars) were characterized by their molecular distributions and {sup 13}C/{sup 12}C isotope ratios. It was found that for all oil samples, the molecular and isotopic profiles for their asphaltene-derived PAHs are both similar to those observed for their contained free aromatics, with {sup 13}C-isotopic values varying from -25 to -27{per_thousand} for the Nigerian and -27 to -30{per_thousand} for North Sea oil samples. For low and high temperature coal tar samples, however, similar molecular but different isotopic profiles were observed for their asphaltene-bound PAHs. The free aromatics are significantly isotopically lighter (by nearly -3{per_thousand}) than their asphaltene-derived counterparts having isotopic values typically between -22 and -23{per_thousand} for all coal tar samples examined, and this leads to a larger isotopic difference of up to 7{per_thousand} between the two sources of PAHs than that already observed between their free aromatics (3{per_thousand}). Applying these results to samples previously examined in an area where unambiguous source apportionment could not be conducted for the PAHs due to likely biodegradation, it was found that the bound PAHs released from the asphaltenes recovered from the soil samples in this area are extremely similar to low temperature tar as the source, in terms of their both molecular (highly alkylated) and isotopic profiles. The free PAHs are much less alkyl substituted confirming that the aromatics detected in this area have been subjected to intensiveenvironmental degradation with alkylated aromatic constituents being preferentially removed from their initial matrix.

Study of flow properties of asphaltenic oils in a porous medium; Etude des proprietes d`ecoulement des bruts asphalteniques en milieu poreux

Energy Technology Data Exchange (ETDEWEB)

Petrova-Bensalem, R.

1998-06-30

Deposits of asphaltenes during production can adversely affect the exploitation of certain fields, that of Hassi Messaoud is a known example. The objective of this study is essentially focused on the damage aspects due to formation of this deposits. A methodology has been developed which makes it possible to determine the flow properties of asphaltenic oils in a porous medium under conditions close to those of a reservoir and to detect the formation of organic deposits in situ. Several types of rocks with different morphology were selected along with a number of asphaltenic oils having varied geographic origins. It was shown with these that it was possible to evaluate, in laboratory, the reduction in permeability to the oil resulting from an asphaltene deposit during the circulation of crude oil in the samples. It was observed that the variation in blocking the cores as a function of the volume of injected fluid is similar to the blocking kinetics ascertained for the retention of solid suspended particles in injection water. This similarity in the phenomena led to using particle damage models developed for the latter case. Several experiments involving blocking by asphaltenes could thus be satisfactory simulated, showing that this approach is worth developing despite the differences between the two types of colloidal suspension. The method using injection or `squeeze` of co- solvents was studied with the same systems (rock/crude oil) as a possible remedy for asphaltene deposition. To select suitable solvents and additives. A methodology was established based on application of Hansen`s theory for adjusting the polarity of solvent to the chemical properties of the asphaltene to be eliminated. This was combined with a series of in vitro tests with separated asphaltenes and the minerals of the reservoir rock. The efficiency of the co-solvents thus selected was verified by slug injection in to cores which has been damaged by asphaltenes. This approach may well help the

Prediction of Gas Injection Effect on Asphaltene Precipitation Onset Using the Cubic and Cubic-Plus-Association Equations of State

DEFF Research Database (Denmark)

Arya, Alay; Liang, Xiaodong; von Solms, Nicolas

2017-01-01

Gas injection is a proven enhanced oil recovery technique. The gas injection changes the reservoir oil composition, temperature, and pressure conditions, which may result in asphaltene precipitation. In this work, we have used a modeling approach from the literature in order to predict asphaltene...

Asphaltene-bearing mantle xenoliths from Hyblean diatremes, Sicily

Science.gov (United States)

Scirè, Salvatore; Ciliberto, Enrico; Crisafulli, Carmelo; Scribano, Vittorio; Bellatreccia, Fabio; Ventura, Giancarlo Della

2011-08-01

Microscopic blebs of sulfur-bearing organic matter (OM) commonly occur between the secondary calcite grains and fibrous phyllosilicates in extensively serpentinized and carbonated mantle-derived ultramafic xenoliths from Hyblean nephelinite diatremes, Sicily, Italy. Rarely, coarse bituminous patches give the rock a blackish color. Micro Fourier transform infrared spectra (μ-FTIR) point to asphaltene-like structures in the OM, due to partially condensed aromatic rings with aliphatic tails consisting of a few C atoms. X-ray photoelectron spectroscopy (XPS) analysis indicates the occurrence of minor S═O (either sulphonyl or sulphoxide) functional groups in the OM. Solubility tests in toluene, thermo-gravimetric (TGA) and differential thermal (DTA) analyses confirm the presence of asphaltene structures. It is proposed that asphaltenes derive from the in situ aromatization (with decrease in H/C ratio) of previous light aliphatic hydrocarbons. Field evidence excludes that hydrocarbon from an external source percolated through the xenolith bearing tuff-breccia. The discriminating presence of hydrocarbon in a particular type of xenolith only and the lack of hydrocarbon in the host breccia matrix, are also inconsistent with an interaction between the ascending eruptive system and a supposed deep-seated oil reservoir. Assuming that the Hyblean unexposed basement consists of mantle ultramafics and mafic intrusive rocks having hosted an early abyssal-type hydrothermal system, one can put forward the hypothesis that the hydrocarbon production was related to hydrothermal activity in a serpentinite system. Although a bacteriogenesis or thermogenesis cannot be ruled out, the coexisting serpentine, Ni-Fe ores and hydrocarbon strongly suggest a Fischer-Tropsch-type (FTT) synthesis. Subsequent variations in the chemical and physical conditions of the system, for example an increase in the water/rock ratio, gave rise to partial oxidation and late carbonation of the serpentinite

Synthesis and evaluation of copolymer based on cardanol and styrene on the stability of asphaltenes; Sintese e avaliacao de copolimero a base de cardanol e estireno sobre a estabilidade dos asfaltenos

Energy Technology Data Exchange (ETDEWEB)

Loureiro, Tatiana S.; Spinelli, Luciana S., E-mail: tatianaloureiro@ima.ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil). Instituto de Macromoleculas

2015-07-01

The destabilization of asphaltenes in crude oil mainly happens due to variations in pressure, temperature and oil composition, causing significant losses. Polymers containing specific groups can be used as asphaltenes stabilizers and thus, avoid your precipitation, or as asphaltenes flocculants to assist the removal of suspended particles in a particular oil. The monitoring of asphaltenes precipitation is usually evaluated by tests with variation in stability of asphaltenes in function of adding a flocculant solvent. In this work, it was evaluated the influence of a synthesized copolymer based on cardanol and styrene on the stability of asphaltenes. The stability of asphaltenes was monitored by precipitation tests induced by a flocculant agent (n-heptane), using an ultraviolet-visible (UV-Vis) spectrometer. The structural characterization of copolymer was performed by FTIR and {sup 1}H NMR. The results showed that copolymer can act as asphaltene flocculant. (author)

Effect of resins of heat exchanger fouling by asphaltene-containing oils

Energy Technology Data Exchange (ETDEWEB)

Al-Atar, E.; Watkinson, A.P. [British Columbia Univ., Dept. of Chemical and Bio-Resource Engineering, Vancouver, BC (Canada)

1999-07-01

The effects of resins on the thermal fouling of asphaltene containing oils in heat exchangers was investigated as well as the nature of the deposits. Building on previous research, a sample of de-asphalted vacuum bottoms (DAO), serving as a source of natural resins, heavy oil (HO) and fuel oil was used to investigate the effects of resin concentration on the rate of thermal fouling. The conditions of the study included: fluid circulation through the UBC annular fouling test section for up to 30 hour periods, monitoring of thermal fouling by measurement, and nitrogen atmospheres at a bulk temperature of 85 degrees C, a bulk velocity of 0.85 am/s, and a pressure of 410 kPa. Physical and chemical characterization of the deposits was affected, and filtration at the bulk temperature before and after a run was used to determine the occurrence of fine solids in the fluid. The rate of fouling generally decreased tending generally towards asymptotic behavior in the limit, and after one day Rf values up to 0.3 m2K/kW occurred with severe fouling. An increase in the fouling rate occurred with increased DAO concentration in the mixture, at a fixed heavy oil concentration of 5 weight percent, and the relation between Asomaning's colloidal instability index and the trends in fouling rate was not observed, although there were some indications of reduced fouling as there was an increase in the ratio of resins to asphaltenes, however, blends of the DAO-HO-FO helped to control the concentration of asphaltenes and resins that are possible. (Abstract only).

Biological marker distribution in coexisting kerogen, bitumen and asphaltenes in Monterey Formation diatomite, California

Science.gov (United States)

Tannenbaum, E.; Ruth, E.; Huizinga, B. J.; Kaplan, I. R.

1986-01-01

Organic-rich (18.2%) Monterey Formation diatomite from California was studied. The organic matter consist of 94% bitumen and 6% kerogen. Biological markers from the bitumen and from pyrolysates of the coexisting asphaltenes and kerogen were analyzed in order to elucidate the relationship between the various fractions of the organic matter. While 17 alpha(H), 18 alpha(H), 21 alpha(H)-28,30-bisnorhopane was present in the bitumen and in the pryolysate of the asphaltenes, it was not detected in the pyrolysates of the kerogen. A C40-isoprenoid with "head to head" linkage, however, was present in pyrolysates of both kerogen and asphaltenes, but not in the bitumen from the diatomite. The maturation level of the bitumen, based on the extent of isomerization of steranes and hopanes, was that of a mature oil, whereas the pyrolysate from the kerogen showed a considerably lower maturation level. These relationships indicate that the bitumen may not be indigenous to the diatomite and that it is a mature oil that migrated into the rock. We consider the possibility, however, that some of the 28,30-bisnorhopane-rich Monterey Formation oils have not been generated through thermal degradation of kerogen, but have been expelled from the source rock at an early stage of diagenesis.

Time-resolved small angle neutron scattering measurements of asphaltene nanoparticle aggregation kinetics in incompatible crude oil mixtures

International Nuclear Information System (INIS)

Mason, Thomas G.; Lin, Min Y.

2003-01-01

We use time-resolved-small angle neutron scattering to study the kinetics of asphaltene nanoparticle aggregation in incompatible crude oil mixtures. We induce asphaltene aggregation by mixing asphaltene-rich Syrian crude oil (SACO) with a paraffinic British crude oil and observe the scattered neutron intensity, I, as a function of wave number, q, over times, t, ranging from twenty minutes to about a week. We observe a growth in I at low q as the nanoscale asphaltenes agglomerate into microscale aggregates and interpret this growth as an increase in surface scattering from the aggregates. We fit I(q,t) to an empirical model and measure the growth in the power-law exponent, α, associated with the low-q logarithmic slope of I(q). We define a time, τ α , associated with the first appearance of the aggregates when α>3; τ α increases as a function of the volume fraction, φ m , of SACO in the mixture. The surface scattering intensity initially increases and then saturates at long times when the aggregate structures no longer evolve at the length scales we probe. Based on this saturation, we define a time scale, τ I , which is larger than τ α but has essentially the same dependence on φ m . We interpret τ α (φ m ) and τ I (φ m ) in terms of a simple aggregation model based on diffusion-limited kinetics and a repulsive potential barrier that models the effective solvent quality

EPR spectroscopy in the asphaltenes photodegradation study in petroleum

International Nuclear Information System (INIS)

Mauro, Eduardo di; Nakaema, Marcelo Kiyoshi Kian; Melo, Fernando Alves de; Turini, Marilene; Guedes, Carmen Luisa Barbosa; Nascimento, Otaciro Rangel

2003-01-01

Full text: The knowledge of the photochemistry transformation that occurs in the petroleum, when it is exposed to the environment has already been proved. In tropical climates, where the solar intensity is high and biological processes are hindered by the lack of nutrients, photochemical processes can be the one that most contribute for the degradation of oil. Moreover, photochemical processes can be important for subsequent biological consumption of oil (Nicodem et al., 1997). We have used EPR with the purpose of getting information of the photodegradation of the asphaltenes concerning the molecular structure. The EPR spectra of petroleum presented a single sign for organic free radicals. The present work basically consists of showing a new assignment of the EPR spectra to organic free radical. The sign observed in the EPR spectra in the Q-band for Arabian and Colombian oils was simulated mathematically. In contrast to the hypothesis postulated until now, that the sign corresponding to the free radical is interpreted as resulting from the superposition of the signs of different species of radicals in petroleum asphaltenes, the hypothesis that the asymmetrical line is the result of the components of the g tensor for a single radical species was proposed. The performed simulation was perfectly adjusted to the sign of the radical, confirming that this sign is the representation of a single species of free radical. Although the sign of the radical is due to a single species in each oil, the species responsible for the sign in Arabian petroleum is different from that responsible for the sign in Colombian petroleum. Nicodem, D.E., Fernandes, M.C.Z., Guedes, C.L.B., Correia, R.J., 1997. Biogeochemistry 39, 121-138. (author)

Modeling of Asphaltene Onset Precipitation Conditions with Cubic Plus Association (CPA) and Perturbed Chain Statistical Associating Fluid Theory (PC-SAFT) Equations of State

DEFF Research Database (Denmark)

Arya, Alay; Liang, Xiaodong; von Solms, Nicolas

2016-01-01

using various equations of state and empirical models. In the past few years, association models based on CPA and SAFT equations of state have been found to be promising models for studies of asphaltene precipitation. In this work, we compare asphaltene precipitation results obtained from different...

Study of Asphaltene Solutions by Electrical Conductivity Measurements Conductivité électrique des solutions d'asphaltènes

Directory of Open Access Journals (Sweden)

Behar E.

2006-11-01

Full Text Available The asphaltene interactions in model solutions were studied using a technique based on the electrical conductivity measurement. Interactions with n-heptane, resins, surfactants, water, phenol and NaCI were investigated. The conclusions drawn from this study confirmed previous opinions on aggregation mechanism of asphaltenes in solutions. They confirmed also the interpretation of asphaltene behaviour in terms of colloidal solution theories. Les interactions des asphaltènes avec leur environnement moléculaire dans des solutions modèles ont été étudiées par la mesure de la conductivité électrique de ces solutions. Les interactions avec le n-heptane, des résines, des tensioactifs, l'eau, le phénol et le chlorure de sodium ont été explorées. Les conclusions tirées de cette étude ont confirmé certaines hypothèses faites sur les mécanismes d'agrégation des asphaltènes en solution, en particulier dans le cadre de la théorie des solutions colloïdales.

Determination of asphaltene onset conditions using the cubic plus association equation of state

DEFF Research Database (Denmark)

Arya, Alay; von Solms, Nicolas; Kontogeorgis, Georgios M.

2015-01-01

The cubic-plus-association (CPA) equation of state (EoS) has already been proven to be a successful model for phase equilibrium calculations for systems containing associating components and has already been applied for asphaltene modeling by few researchers. In the present work, we apply the CPA...

Multi-scale simulation and experimental studies of asphaltene aggregation and deposition in capillary flow

NARCIS (Netherlands)

Boek, E.S.; Wilson, A.D.; Padding, J.T.; Headen, T.F.; Crawshaw, J.P.

2010-01-01

Asphaltenes are known as the "cholesterol" of crude oil. They form nanoaggregates, precipitate, adhere to surfaces, block rock pores, and may alter the wetting characteristics of mineral surfaces within the reservoir, hindering oil recovery efficiency. Despite a significant research effort, the

Probing the Carbonyl Functionality of a Petroleum Resin and Asphaltene through Oximation and Schiff Base Formation in Conjunction with N-15 NMR.

Directory of Open Access Journals (Sweden)

Kevin A Thorn

Full Text Available Despite recent advances in spectroscopic techniques, there is uncertainty regarding the nature of the carbonyl groups in the asphaltene and resin fractions of crude oil, information necessary for an understanding of the physical properties and environmental fate of these materials. Carbonyl and hydroxyl group functionalities are not observed in natural abundance 13C nuclear magnetic resonance (NMR spectra of asphaltenes and resins and therefore require spin labeling techniques for detection. In this study, the carbonyl functionalities of the resin and asphaltene fractions from a light aliphatic crude oil that is the source of groundwater contamination at the long term USGS study site near Bemidji, Minnesota, have been examined through reaction with 15N-labeled hydroxylamine and aniline in conjunction with analysis by solid and liquid state 15N NMR. Ketone groups were revealed through 15N NMR detection of their oxime and Schiff base derivatives, and esters through their hydroxamic acid derivatives. Anilinohydroquinone adducts provided evidence for quinones. Some possible configurations of the ketone groups in the resin and asphaltene fractions can be inferred from a consideration of the likely reactions that lead to heterocyclic condensation products with aniline and to the Beckmann reaction products from the initially formed oximes. These include aromatic ketones and ketones adjacent to quaternary carbon centers, β-hydroxyketones, β-diketones, and β-ketoesters. In a solid state cross polarization/magic angle spinning (CP/MAS 15N NMR spectrum recorded on the underivatized asphaltene as a control, carbazole and pyrrole-like nitrogens were the major naturally abundant nitrogens detected.

Probing the carbonyl functionality of a petroleum resin and asphaltene through oximation and schiff base formation in conjunction with N-15 NMR

Science.gov (United States)

Thorn, Kevin A.; Cox, Larry G.

2015-01-01

Despite recent advances in spectroscopic techniques, there is uncertainty regarding the nature of the carbonyl groups in the asphaltene and resin fractions of crude oil, information necessary for an understanding of the physical properties and environmental fate of these materials. Carbonyl and hydroxyl group functionalities are not observed in natural abundance 13C nuclear magnetic resonance (NMR) spectra of asphaltenes and resins and therefore require spin labeling techniques for detection. In this study, the carbonyl functionalities of the resin and asphaltene fractions from a light aliphatic crude oil that is the source of groundwater contamination at the long term USGS study site near Bemidji, Minnesota, have been examined through reaction with 15N-labeled hydroxylamine and aniline in conjunction with analysis by solid and liquid state 15N NMR. Ketone groups were revealed through 15N NMR detection of their oxime and Schiff base derivatives, and esters through their hydroxamic acid derivatives. Anilinohydroquinone adducts provided evidence for quinones. Some possible configurations of the ketone groups in the resin and asphaltene fractions can be inferred from a consideration of the likely reactions that lead to heterocyclic condensation products with aniline and to the Beckmann reaction products from the initially formed oximes. These include aromatic ketones and ketones adjacent to quaternary carbon centers, β-hydroxyketones, β-diketones, and β-ketoesters. In a solid state cross polarization/magic angle spinning (CP/MAS) 15N NMR spectrum recorded on the underivatized asphaltene as a control, carbazole and pyrrole-like nitrogens were the major naturally abundant nitrogens detected.

Isothermal Titration Calorimetry and Fluorescence Spectroscopy Study Of Asphaltene Self-Association In Toluene And Interaction With A Model Resin

DEFF Research Database (Denmark)

Garcia, Daniel Merino; Andersen, Simon Ivar

2002-01-01

This article collects the work performed by Isothermal Titration Caloritnetry (ITC) in the study of the self-association of asphaltenes in toluene solutions. Calorimetric experiments show that asphaltenes, start self-associating at very low concentrations and that the existence of a Critical...... with the results of the titration of three model molecules: nonylphenol, which associates by means of hydrogen bond formation, and coronene and pyrene, which associates by stacking. The results obtained leave open the question about the model-stacking molecules, as it was not possible to elucidate whether they do...

Study of the colloidal structure of crude oils - Characterisation of asphaltene suspensions. Relationships between microscopic description and macroscopic properties under different conditions

International Nuclear Information System (INIS)

Guille, Veronique; Espinat, Didier; Ravey, Jean-Claude

1994-04-01

The authors report the use of techniques of X-ray and neutron scattering, and of rheological measurements to characterise the macrostructure of asphaltenes in solution. They confirm the relevance of a lamellar model for asphaltene particles. They also show that the addition of resin particles results in a decrease of asphaltene size, and hides solvent effects. They also performed a characterisation of the residue of a vacuum distillation. Rheological measurements showed that this residue behaves like a Newtonian liquid above 100 C. Scattering spectra reveal a structure modification between 20 and 90 C. No significant change of the scattering spectrum is then noticed, even up to 300 C. It appears that the scattering technique does not allow an observation of structure modifications to be performed on a large size range [fr

Adsorption Isotherms of Phenol and 4-Chlorophenol on Petroleum Asphaltenes Adsorption du phénol et du 4-chlorophénol sur les asphaltènes pétroliers

Directory of Open Access Journals (Sweden)

Jaoui M.

2006-11-01

Full Text Available The adsorption isotherms for phenol and 4-chlorophenol from water onto asphaltenes flocculated in bulk and asphaltenes deposited on silica were established by frontal analysis chromatography at 293, 298, 303, and 308 K. The adsorption was more important with asphaltenes flocculated in bulk and corresponded to a Freundlich isotherm mechanism. The high adsorbed amount of phenols suggests possible migration of phenols through the loose asphaltene structure. Isotherms observed with the silica coated by asphaltenes showed that adsorption occurs in two stages corresponding probably to two different organizations of solute molecules at the surface. Les isothermes d'adsorption du phénol et du 4-chlorophénol en solution dans l'eau sur des asphaltènes floculés en masse et sur des asphaltènes déposés sur de la silice ont été déterminés par analyse chromatographique frontale à 293, 298, 303 et 308 K. L'adsorption sur des asphaltènes floculés en masse était la plus importante avec des isothermes correspondant à un mécanisme de Freundlich. La quantité élevée de phénols adsorbés suggère une migration possible des molécules du phénol à travers la structure peu compacte des asphaltènes. Les isothermes observés dans le cas de silice tapissée d'asphaltènes ont montré que l'adsorption se produit en deux étapes correspondant probablement à deux organisations différentes des molécules de soluté à la surface.

The influence of asphaltenes of the petroleum on the rheology of O/W (Oil/Water) emulsions; Influencia de asfaltenos do petroleo sobre a reologia de emulsoes O/A (Oleo/Agua)

Energy Technology Data Exchange (ETDEWEB)

Santos, Ronaldo Goncalves dos; Mohamed, Rahoma Sadeg; Loh, Watson; Bannwart, Antonio Carlos [Universidade Estadual de Campinas (UNICAMP), Campinas, SP (Brazil)

2004-07-01

Heavy oils represent a large fraction of the Brazilian petroleum reserves and display a great potential for application as substitute to the conventional oils, provided a suitable technology for their transportation is available. The high viscosity of these heavy oils leads to high flow resistance and increase in the recovery and transportation costs. Methodologies employed to reduce these problems involve application of heat of addition of diluents or lighter oils, but are associated with high costs. Formation of low viscosity oil-in-water emulsions has been proposed as an alternative for the transportation of heavy oils, as investigated in this work. Preliminary results indicate significant viscosity decreases upon emulsification of heavy oils (viscosities greater than 1,000 cP) forming o/w emulsions with high oil content (between 50-65 vol. %), which display viscosities within 4-25 cP. Additionally, the effect of different surfactants, methodology of preparation and oil asphaltene content on the emulsion stability was also evaluated. These results confirm the potential of emulsification as a viable methodology for heavy oil transportation. (author)

Géochimie des résines et asphaltènes Geochernistry of Resins and Asphaltenes

Directory of Open Access Journals (Sweden)

Tissot B.

2006-11-01

, thus providing a new correlation tool for crude oils. Heavy constituents are not favored, as compared to hydrocarbons, during migration from the source rock to the reservoir, where they are less abundant. The occurrence of a macrostructure of asphal-tenes and resins, such as micelles or aggregates, is probably responsible for the high viscosity of heavy oils. A better understanding of the macrostructure may result in new techniques to lower viscosity and improve recovery of heavy oils.

Recent developments in the deposition of colloidal asphaltene in capillary flow : experiments and mesoscopic simulation

NARCIS (Netherlands)

Wilson, A.D.; Boek, E.S.; Ladva, H.K.; Crawshaw, J.; Padding, J.T.

2009-01-01

The aggregation and deposition of asphaltenic material in reservoir rock are significant problems in the oil industry and can adversely affect the producibility of a given reservoir. To obtain a fundamental understanding of this phenomenon, we have studied the deposition and aggregation of colloidal

Adsorption of petroleum resins and asphaltenes onto reservoir rock sands studied by near infrared (NIR) spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Syunyaev, R.Z.; Balabin, R.M. [Russian State Univ. of Oil and Gas, Moscow (Russian Federation). Dept. of Physics; Akhatov, I.S. [North Dakota State Univ., Fargo, ND (United States). Dept. of Mechanical Engineering and Center for Nanoscale Science and Engineering

2008-07-01

The presence of asphaltene and resin in crude oil is known to cause well bore plugging and pipeline deposition; stabilization of water/oil emulsions; sedimentation and plugging during crude oil storage; adsorption on refining equipment and coke formation. Kinetic and thermodynamic parameters of adsorption are also known to influence wettability and the capillary number. In this study, adsorption parameters of petroleum resins and asphaltenes were evaluated by Near Infrared (NIR) spectroscopy. Fractioned quartz, dolomite, mica and kaolinite sands were used as adsorbent. The particle size distribution was evaluated using an optical microscope. Porosity and permeability of each fraction were designed and benzene was used as the solvent. Various approaches for calibrating NIR spectra-macromolecules concentration were discussed. In this study, the partial least squares (PLS) regression method was used and the Langmuir model was chosen for experimental data fitting. Kinetic and isothermic data was used to evaluate the maximal adsorbed mass density, the equilibrium constant of adsorption, and the rate constants of adsorption and desorption. The rate constants of resins adsorption and desorption depended on the concentration. A numerical algorithm was developed to estimate the diffusion coefficient and relaxation time from the experimental data.

Avaliação geoquímica de biomarcadores ocluídos em estruturas asfaltênicas Geochemical evaluation of occluded biomarkers in asphaltenic structures

Directory of Open Access Journals (Sweden)

Débora de Almeida Azevedo

2009-01-01

Full Text Available Asphaltenes from two Brazilian crude oils were submitted to mild oxidation to disrupt their structure, releasing the occluded oil. The released hydrocarbons were compared with those from the original crude oil, and used to evaluate the alteration of the oils, especially as a result of biodegradation, but also thermal maturity. The crude oils used are depleted in n-alkanes, which are usually related to biodegradation. However, the released products from the corresponding asphaltenes have n-alkane distributions from nC10 to nC40, suggesting a protection effect from biodegradation. The m/z 191 mass chromatograms showed higher relative intensities for tricyclic terpanes than the hopanes in the crude in comparison with the released ones.

The determination of maturity levels in source rocks of the La Luna Formation, Maracaibo Basin, Venezuela, based on convention geochemical parameters and asphaltenes; Determinacao do grau de maturacao em rochas geradoras de petroleo, formacao La Luna, Bacia de Maracaibo, Venezuela: parametros geoquimicos convencionais e asfaltenos

Energy Technology Data Exchange (ETDEWEB)

Castro, L.P. de [Pontificia Universidade Catolica (PUC-RS), Porto Alegre, RS (Brazil). Centro de Excelencia em Pesquisas sobre o Armazenamento de Carbono; Franco, N. [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil). Dept. de Geologia; Lopez, L.; Lo Monaco, S.; Escobar, G. [Universidad Central de Venezuela (UCV), Caracas (Venezuela); Kalkreuth, W. [Universidade Federal do Rio Grande do Sul (UFRGS), Porto Alegre, RS (Brazil). Centro de Excelencia em Analises de Carvao e Rochas Geradoras de Petroleo

2008-07-01

The La Luna Formation, main source rock of the Maracaibo Basin was studied by conventional geochemical parameters, used to determine the maturity, and they were compared with the physic-chemical and molecular properties of the asphaltenes present in the bitumen of the rocks. Three wells were studied (A, B and C) with a total of 13 samples. Based on Rock-Eval results the organic matter in well A (455 deg C Tmax) shows a relatively high level of maturation (top of the oil window), whereas the organic matter in well B (435 - 436 deg C Tmax) is in the beginning of the oil window. Tmax values in well C (438 - 446 deg C) and well C suggest an intermediate maturity level. The biomarkers identified in well B and C show ratios indicating an equilibrium state in the maturity level. A good correlation was found comparing the conventional analytical data with the determination of maturity level obtained from the asphaltenes precipitated from the bitumen of the samples. With increased maturity levels the H1 NMR analysis showed enrichment in aromatic molecules in relation to aliphatic, due to the bitumen aromatization process. Similarly, the asphaltenes molecular weight has higher values in samples characterized by elevated maturity levels. This confirms earlier studies that showed that asphaltenes may be utilized as maturity parameter of organic matter. (author)

Effect of asphaltene and resin oils on the viscosity of bituminous petroleum materials to be used as asphalt primers

Directory of Open Access Journals (Sweden)

Bencomo, M. R.

2006-03-01

Full Text Available The bituminous crude from the Machete, Venezuela, area, which has such a fluid consistency that it falls outside the normal scope of the A5TM D-5 (1 penetration test exceeding the 3D-mm ceiling specified in that standard and can be used as an asphalt primer: Like other asphalt products, these materials are -chemically speaking- a mix of numerous naphthenic, paraffinic and aromatic hydrocarbons and heterocyclic compounds containing sulphur, nitrogen, oxygen and so on. They have a dense and a malthene oil phase which, along with the natural hydrocarbons additives used in these products acts as a volatile fluidizer. The former is described as a mix of asphaltenes: complex high molecular weight substances that are insoluble in paraffinic hydrocarbons and soluble in aromatic compounds such as benzene. The malthene oil phase, in turn, consists in a mix of resins and hydrocarbons and together the two constitute a colloidal system. The experiments discussed in the present paper were conducted to determine the effect of the proportion of asphaltenes and resin oils on the viscosity of such bituminous crude emulsions/ with a view to their use as primers. These experiments were run in a Parr batch reactor in a nitrogen atmosphere using n-heptane as a solvent. The resins were separated after the asphaltenes precipitated from the samples and subsequently from the malthene fraction obtained. The results showed that the asphaltenes account for the structural characteristics and consistency of the medium and the resin oils for its cohesive properties/,the malthene oils act as solvents.Los crudos extrapesados procedentes del área Machete (Venezuela son materiales de consistencia blanda o fluida, por lo que se salen del campo en el que normalmente se aplica el ensayo de penetración a productos asfálticos según el método ASTM D-5 (1, cuyo límite máximo es 30 mm, y pueden ser utilizados como pinturas asfálticas de imprimación. Al igual que otros productos

Colloidal Structure of Heavy Crudes and Asphaltene Soltutions Structure colloïdale des bruts lourds et des suspensions d'asphaltènes

Directory of Open Access Journals (Sweden)

Barre L.

2006-12-01

Full Text Available Many industrial problems that arise during petroleum processing are related to the high concentration of asphaltenes. A good knowledge of the chemical composition of these macromolecules and a detailed understanding of the evolution of the colloïdal structures present in oil and its derivatives can play a decisive role in improving processing facilities. Asphaltenes are defined by their insolubility in n-heptane. Soluble molecules are called maltenes which can be fractionated by liquid chromatography in so-called resins, aromatic and saturated fractions. The major part of the research carried out on these complex molecules concerned the chemical composition determination from powerful techniques measurements as for instance IR or NMR methods. Nevertheless, very little information on the colloïdal structure of asphaltenes or resins in pure solvent or in real systems is accessible.The molecular weight determination was the first objective; several techniques, as vapour pressure osmometry (VPO, were used. The main conclusion of these determinations was the huge variation of the molecular weight measured by different methods. We used X-ray and neutron small angle scattering techniques in order to deduce the size polydispersity and the weight average molecular weight. Different systems as (i asphaltenes or resins in solution with different solvents, or (ii asphaltene and resin mixtures in suspension with good or bad solvents were investigated as a function of temperature increase. We have exhibited that the aggregation number, i.e. the number of smaller entities , can strongly vary with solvent composition and temperature. Resins appear as very good solvent for asphaltene molecules. Scattering measurements often exhibit strong scattered intensity at small scattering vector, showing the presence in the suspension of large heterogeneities in diluted solutions of asphaltenes and resins. We can suggest that these heterogeneities are due to

Chemical modification of a bitumen and its non-fuel uses. [Reactions of tar sand asphaltenes in synthesis of non-fuel products

Energy Technology Data Exchange (ETDEWEB)

Moschopedis, S.E.; Speight, J.G.

1974-01-01

Simple reactions are described whereby tar sand bitumen can be converted to a whole range of materials. Examples are given to illustrate the non-fuel uses of the products. The following reactions of Athabasca asphaltenes are considered: oxidation, halogenation, sulfonation and sulfomethylation, phosphorylation, hydrogenation, reactions with S and O, reactions with metal salts, and miscellaneous chemical conversions. (JGB)

Quantitative analysis of properties of petroleum mixtures by near infrared spectroscopy; Analise quantitativa de propriedades de misturas de petroleos via espectrofotometria no infravermelho proximo

Energy Technology Data Exchange (ETDEWEB)

Santos, Leila M.; Silva, Elisangela B.; Fortuny, Montserrat; Dariva, Claudio; Santos, Alexandre F. [Universidade Tiradentes (UNIT), Aracaju, SE (Brazil). Instituto de Tecnologia e Pesquisa (ITP); Araujo, Augusto M. [Siemens Brazil, Rio de Janeiro, RJ (Brazil); Coutinho, Raquel C.C. [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES)

2008-07-01

An experimental study is carried out aiming to develop a method of quantitative analysis of properties of petroleum mixtures, such as water and asphaltene contents, heavy oil concentration and viscosity based on the use of a NIR spectrophotometer. A strategy of generation of crude oil mixtures with known properties was developed to help calibrating the NIR spectrophotometer. Petroleum mixtures involving 2 or 3 oils under known ratios were prepared based on a set of different light and heavy Brazilian crude oil samples. Moreover, experimental data of 5 binary mixtures were also assembled into a data set named multi-compound. Results indicated that excellent calibration models can be obtained for binary mixtures with correlation coefficient (R{sup 2}) greater than 99% for water and asphaltene contents, viscosity and heavy oil concentration. For ternary systems, excellent correlations (R{sup 2}>99%) can be attained for asphaltene and heavy oil contents. Finally for the multi-compound data set, the asphaltene content was the only property that resulted in R{sup 2}>99%, which demonstrates the adequacy of the NIR technique for assessing this property. (author)

Optimization of asphaltenes decantation equipment used in deasphalting process using computational fluid dynamics; Otimizacao de um equipamento para a decantacao de asfaltenos no processo de desasfaltacao usando fluidodinamica computacional

Energy Technology Data Exchange (ETDEWEB)

Arenales, Carlos Gregorio Dallos [Cooperativa de Trabajadores Profesionales Ltda (CTP), Santander (Colombia); Pimiento, Carlos Eduardo Lizcano; Quintero, Lina Constanza Navarro; Bueno, Jhon Ivan Penaloza [Empresa Colombiana de Petroleos S.A. (ICP/ECOPETROL), Santander (Colombia). Instituto Colombiano del Petroleo

2012-07-01

Heavy crude oil is a complex mixture of compounds that include saturates, aromatics, resins and asphaltenes. In this mixture, the asphaltenes are the heaviest components and can be unstable and precipitate. This kind of components causes troubles in transportation and processing. One way to reduce this problem is through technologies that use solvents, which under adequate operating conditions, separate the heavy fraction, improving the properties and conditions for transporting and refining of heavy crude oil. One of the processes used in the petroleum industry to improve the properties of heavy and residue oil is the solvent deasphalting. These processes have the disadvantage of work at elevated pressure and temperature. The Colombian Petroleum Company, ECOPETROL S.A. has developed its own process of upgrading heavy oils, ECODESF, a process that is designed to work at moderate conditions of pressure and temperature and that by using a paraffinic solvent, significantly improves the quality of heavy oil, reducing its viscosity and increasing API gravity. The present work develops a model of computational fluid dynamics (CFD) for asphaltene settler, using microscopic balance. The response of this model allowed determine: the solids flow pattern distribution and accumulation points of heavy phase. This information is useful for understanding the fluid-dynamic behavior of the system. The model was validated using data from a pilot plant with capacity for treatment 1.25 BPD of heavy crude oil. This pilot plant is located in the Colombian Petroleum Institute of ECOPETROL (ICP), Piedecuesta city, Santander, Colombia. (author)

Fractal characteristics of an asphaltene deposited heterogeneous surface

International Nuclear Information System (INIS)

Amin, J. Sayyad; Ayatollahi, Sh.; Alamdari, A.

2009-01-01

Several methods have been employed in recent years to investigate homogeneous surface topography based on image analysis, such as AFM (atomic force microscopy) and SEM (scanning electron microscopy). Fractal analysis of the images provides fractal dimension of the surface which is used as one of the most common surface indices. Surface topography has generally been considered to be mono-fractal. On the other hand, precipitation of organic materials on a rough surface and its irregular growth result in morphology alteration and converts a homogeneous surface to a heterogeneous one. In this case a mono-fractal description of the surface does not completely describe the nature of the altered surface. This work aims to investigate the topography alteration of a glass surface as a result of asphaltene precipitation and its growth at various pressures using a bi-fractal approach. The experimental results of the deposited surfaces were clearly indicating two regions of micro- and macro-asperities namely, surface types I and II, respectively. The fractal plots were indicative of bi-fractal behavior and for each surface type one fractal dimension was calculated. The topography information of the surfaces was obtained by two image analyses, AFM and SEM imaging techniques. Results of the bi-fractal analysis demonstrated that topography alteration in surface type II (macro-asperities) is more evident than that in surface type I (micro-asperities). Compared to surface type II, a better correlation was observed between the fractal dimensions inferred from the AFM images (D A ) and those of the SEM images (D S ) in surface type I.

Experimental Investigation of the Asphaltene Deposition Process during Different Production Schemes Étude expérimentale du processus de dépôt d’asphaltènes au cours de différents modes de production

Directory of Open Access Journals (Sweden)

Bagheri M.B.

2011-02-01

Full Text Available This paper presents the results of asphaltene precipitation and deposition during lean gas injection, CO2 injection and natural depletion in reservoir conditions. In addition, the effect of variations in operating pressure, injection gas concentration and production rate on asphaltene precipitation and deposition were investigated. The severity of asphaltene deposition was found to be more pronounced in lean gas injection in comparison with CO2 injection and natural depletion. Increasing the flow rate in natural depletion experiments showed a considerable increase in asphaltene deposition, and consequently permeability reduction in the core matrix. Moreover, more asphaltene deposition was observed along the porous media in the gas injection experiments when the gas mol percent of the mixture was increased. Cet article présente les résultats d’une étude de la précipitation et du dépôt d’asphaltènes qui peuvent se produire lors d’une injection de gaz pauvre, d’une injection de CO2 ou d’une déplétion naturelle en conditions de réservoir. En outre, les effets de la pression de fonctionnement, de la concentration en gaz injecté et du débit de production sur la précipitation et le dépôt d’asphaltènes ont été étudiés. Il a été constaté que l’importance du dépôt d’asphaltènes est plus prononcée dans le cas d’une injection de gaz pauvre comparativement à une injection de CO2 ou à une déplétion naturelle. Une augmentation du débit au cours d’expériences de déplétion naturelle a montré un accroissement considérable du dépôt d’asphaltènes et, en conséquence, une réduction de perméabilité au sein de la matrice poreuse. Par ailleurs, un dépôt d’asphaltènes plus important a été observé au cours des expériences d’injection de gaz lorsque la concentration molaire gazeuse dans le mélange était augmentée.

Solid Organic Deposition During Gas Injection Studies

DEFF Research Database (Denmark)

Dandekar, Abhijit Y.; Andersen, Simon Ivar; Stenby, Erling Halfdan

2000-01-01

Recently a series of first contact miscibility (swelling) experiments have been performed on undersaturated light and heavy oils using LPG rich and methane rich injection gases, in which solid organic deposition was observed. A compositional gradient in the oils during the gas injection process....... The asphaltene content of the different oil samples were determined by the TP 143 method. The standard asphaltenes and the solid organic deposit recovered from the swelling tests were analyzed using FTIR, HPLC-SEC and H-1 NMR. The aim of these analyses is to reveal the molecular nature of the deposits formed...... during the gas injection process in comparison with the standard asphaltenes in order to understand the mechanisms involved in asphaltene deposition....

Far infrared (terahertz) spectroscopy of a series of polycyclic aromatic hydrocarbons and application to structure interpretation of asphaltenes and related compounds.

Science.gov (United States)

Cataldo, Franco; Angelini, Giancarlo; García-Hernández, D Aníbal; Manchado, Arturo

2013-07-01

A series of 33 different polycyclic aromatic hydrocarbons (PAHs) were studied by far infrared spectroscopy (terahertz spectroscopy) in the spectral range comprised between 600 and 50 cm(-1). In addition to common PAHs like naphthalene, anthracene, phenanthrene, fluoranthene, picene, pyrene, benzo[α]pyrene, and perylene, also quite unusual PAHs were studied like tetracene, pentacene, acenaphtene, acenaphtylene, triphenylene, and decacyclene. A series of alkylated naphthalenes and anthracenes were studied as well as methypyrene. Partially or totally hydrogenated PAHs were also object of the present investigation, ranging from tetrahydronaphthalene (tetralin) to decahydronaphthalene (decalin), 9,10-dihydroanthracene, 9,10-dihydrophenanthrene, hexahydropyrene, and dodecahydrotriphenylene. Finally, the large and quite rare PAHs coronene, quaterrylene, hexabenzocoronene, and dicoronylene were studied by far infrared spectroscopy. The resulting reference spectra were used in the interpretation of the chemical structure of asphaltenes (as extracted from a heavy petroleum fraction and from bitumen), the chemical structures of other petroleum fractions known as DAE (distillate aromatic extract) and RAE (residual aromatic extract), and a possible interpretation of components of the chemical structure of anthracite coal. Asphaltenes, heavy petroleum fractions, and coal were proposed as model compounds for the interpretation of the emission spectra of certain proto-planetary nebulae (PPNe) with a good matching in the mid infrared between the band pattern of the PPNe emission spectra and the spectra of these oil fractions or coal. Although this study was finalized in an astrochemical context, it may find application also in the petroleum and coal chemistry. Copyright © 2013 Elsevier B.V. All rights reserved.

Evaluation of nano emulsion containing asphaltenes dispersant additive in dehydration of oil; Avaliacao de nanoemulsoes contendo aditivo dispersante de asfaltenos na desidratacao de petroleo

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Priscila F. de; Rodrigues, Jessica S.; Mansur, Claudia R.E. [Universidade Federal do Rio de Janeiro/ Instituto de Macromoleculas/ Laboratorio de Macromoleculas e Coloides na Industria de Petroleo, Rio de Janeiro, RJ (Brazil)], e-mail: prisfrias@hotmail.com

2011-07-01

Due to the problem of the formation of emulsions type water-oil during oil production, new alternatives of the breakdown of these emulsions have been proposed over the years. Several polymers have been used to destabilize these emulsions and among them are those based on polyphenylene ether. The aim of this study was to develop nanoemulsions type oil / water, where an asphaltenes dispersant additive was dissolved in dispersed phase in order to evaluate them as a new alternative in the breakdown of oil emulsions. The nanoemulsions were prepared in the presence of surfactant based on polyoxide using a high pressure homogenizer (HPH). We obtained stable nanoemulsions for more than 30 days in the presence or absence of additive. These nanoemulsions were effective in water /oil phase separation, and the nanoemulsion containing the dispersant additive provided a faster separation of these phases. (author)

Potential application of oxygen containing gases to enhance gravity drainage in heavy oil bearing reservoirs

Energy Technology Data Exchange (ETDEWEB)

Lakatos, I. [Hungarian Academy of Sciences, Miscolc (Hungary). Lab. for Mining Chemistry; Bauer, K. [Hungarian Academy of Sciences, Miscolc (Hungary). Lab. for Mining Chemistry; Lakatos-Szabo, J. [Hungarian Academy of Sciences, Miscolc (Hungary). Lab. for Mining Chemistry

1997-06-01

In the frame of laboratory studies the effect of air/natural CO{sub 2} mixtures on chemical composition of crude oil and gas phase, the rheological and interfacial properties, the flow mechanism and the safety measures were analyzed. The tests were performed at reservoir conditions (200 bar and 109 C) using natural rock, oil and gas samples. The oxygen content of the gas phase and the gas/oil ratio varied within wide limits. Both crude and asphaltene-free oil were used to determine the consequences of the low temperature oxidation. On the basis of the experimental results it was found that the oxygen content of the cap gas had been completely consumed by the chemical reactions (oxidation, condensation and water formation) before the asphaltene content set in equilibrium. Nearly 9% excess asphaltene formation was observed in both the crude and the asphaltene-free oils. The substantial increase in asphaltene content and the presence of colloidal water results in a measurable change in rheological and interfacial properties. Despite these factors the flow and displacement mechanism is only slightly influenced if the reservoir is of fractured character. On the other hand the in-situ oxidation of this heavy crude oil improves the efficiency of bitumen production and the quality of product used mostly for road construction. As a final statement, it was concluded that replacing the CO{sub 2} with oxygen containing inert gas, the chemical reactions can be in-situ regulated without jeopardizing the recovery efficiency. Application of the artificial gas cap concept opens new perspectives in EOR technology of karstic and fractured reservoirs containing medium and heavy crude oils in those cases where CO{sub 2} or CH gas is not available. (orig./MSK)

Back-echo method for determining the content of C, CH, CH/sub 2/ and CH/sub 3/ fragments

Energy Technology Data Exchange (ETDEWEB)

Polonov, V.M.; Kalabin, G.A.; Kushnarev, D.F.; Latyshev, V.P.

1984-07-01

Possibility was investigated of determining the content of quaternary, tertiary, secondary and primary carbon atoms in soluble products from coal. Cubed residues of medium resin oil from semicoking Cheremkhovskii coals, hydrogenation products from mixtures of medium oil and light dephenolized oil, and asphaltenes separated from the hydrogenation products of Berezovsk coals were used as samples. A new method of quantitative analysis based on the pulse sequence of the back echo from the nuclear magnetic resonance of /sup 13/C was used. The method can be applied in the analysis of light and heavy products from coal, petroleum, shales and complex mixtures of organic substances. The method is limited by a decrease in accuracy when the heteroatom content in the samples increases, causing deterioration in the quality of spectra separation. 13 references.

Modélisation de la combustion de fuels lourds prenant en compte la dispersion des asphaltènes Modeling Heavy Fuel-Oil Combustion (While Considering Or Including Asphaltene Dispersion

Directory of Open Access Journals (Sweden)

Audibert F.

2006-11-01

difficultés relevant du mode d'exploration et de la non adéquation entre les structures asphalténiques et fractales. On a finalement opté pour une détermination visuelle s'appuyant sur les clichés sur lesquels les agglomérats d'asphaltènes sont clairement visualisés tels qu'ils sont dans le fuel. Ce mode d'exploration laborieux a cependant permis de déterminer un modèle construit sur une série de 25 fuels dont 10 ont été brûlés sur une chaudière de 2 MW, et 15 sur un four de 100 kW. Ce modèle fait intervenir les teneurs en carbone Conradson et en métaux, ainsi que le taux de dispersion des asphaltènes. Le perfectionnement des moyens d'exploration aidant, on peut s'attendre à ce que soient disponibles des techniques d'évaluation de la dispersion sur les clichés. Ce paramètre pourra alors être pris en considération pour une meilleure prédiction de résultats de combustion insuffisamment expliqués avec les paramètres classiques. Various models aiming to predict the amount of unburned particles (solids during heavy fuel-oil combustion have been developed. The parameters taken into consideration are generally asphaltenes precipitated by normal heptane or pentane and Conradson carbon as well as the metals content having a known catalytic effect on cenosphere combustion in the combustion chamber. The Exxon and Shell models can be mentioned, which were developed respectively in 1979 and 1981 (Chapter II. Other models also give consideration to the fuel-oil composition, the way it is atomized and diffused in the chamber and the combustion kinetics (research done by the MIT Energy Laboratory published in 1986. However, the above parameters are not the only ones involved. For some fuel oils, experience has shown that the state of dispersion of asphaltenes may also play an important role particularly for combustion installations with mechanical injection for which the dispersion of fuel-oil droplets is not very great and does not affect the structures built

Asphaltenes analysis arising of non conventional oils; Analise de asfaltenos oriundos de petroleos nao convencionais

Energy Technology Data Exchange (ETDEWEB)

Silva, Fernanda B. da; Fiorio, Paula G.P.; Guimaraes, Maria Jose O.C.; Seidl, Peter R. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Escola de Quimica

2012-07-01

The need to use heavy fractions in an efficient way in the production of nobler fractions has motivated the search for ways of separating the asphaltenes, since these molecules increase the viscosity of the fractions submitted to distillation, contribute to the formation of coke and to poisoning and deactivation of catalysts used in process such as cracking, reform, etc, besides provoking cloggings and blockages caused by its deposition, generating losses on the productivity and increases of the operational costs. This paper evaluates the influence of solvent blends (EQ-NP) in the selective extraction of constituents of three samples from Brazilian heavy crude. For the extraction process was used two solvent blends (N1P1 and N1P2). The solvent blend composed of N1P1 showed a higher selectivity in the extraction of aggregates than N1P2. The extracted fraction was characterized by Hydrogen Nuclear Magnetic Resonance ({sup 1}H-NMR) and revealed that the chemical species extracted from different blends exhibit very small differences. (author)

Physical properties and component contents of brown coal tars obtained in semicoking with a solid heat transfer semicoke

Energy Technology Data Exchange (ETDEWEB)

Kuznetsov, V I; Bobrova, A A

1955-01-01

Tar obtained in low-temperature carbonization of brown coals with brown-coal semicoke as a heat-transfer medium contains more water and dust, has a lower drop point, and a higher specific gravity, and contains more asphaltene and less paraffin than does tar from the same coal produced in rotating retorts or in shaft kilns. The brown-coal semicoke used as a heat-transfer medium produces partial thermal cracking of the fuel and polymerization of the products of secondary decompositions. The yield of asphaltenes is lowered when the carbonization temperature is raised.

Could naphthenic acids be responsible for severe emulsion tightness for a low TAN value oil?

Energy Technology Data Exchange (ETDEWEB)

Pauchard, V.; Muller, H.; Al-Hajji, A. [Saudi Aramco, Dhahran (Saudi Arabia). Research and Development Center; Sjoblom, J. [Norwegian Univ. of Technology, Trondheim (Norway). Ugelstad Laboratory; Kokal, S. [Saudi Aramco, Dhahran (Saudi Arabia). EXPEC Advanced Research Center; Bouriat, P.; Dicharry, C. [Univ. de Pau, Pau Cedex (France). Laboratoire des Fluides Complexes, UMR CNRS; Rogers, R. [Florida State Univ., Tallahassee, FL (United States)

2008-07-01

This study re-analyzed the emulsion stabilizing properties of a low Total Acid Number (TAN) of a high asphaltene crude oil with respect to the role of naphthenic acids. The emulsion stability depended on the pressure/pH. The high interfacial activity of indigenous acids extracted from the crude oil was determined by means of Ion Exchange Resins and by the high organic acid content in the interfacial material extracted from a sludge emulsion. The physical origin of these phenomenological observations was identified using the Fourier Transform Ion Cyclotron Resonance Mass Spectrometry (FT-ICR-MS) and pendant droplet experiments. The interfacial material was composed of a mixture of asphaltenes and organic acids having a wide range of structures (monoprotic, diprotic, fatty, naphthenic and perhaps aromatic) and molecular weights. The interfacial rheology was a 2D gel with an assumed glass transition temperature of approximately 40 degrees C. It was concluded that a synergistic effect of asphaltenes and organic acids promoted the build up of a very structured interface. This interface is more resistant to droplets coalescence than less structured interfaces. Therefore, the disruption of the interfacial layer requires the drainage of individual molecules as well as a collective yield of the gel.

Production of jet fuel using heavy crude oil; Producao de combustiveis de aviacao a partir de petroleos pesados

Energy Technology Data Exchange (ETDEWEB)

Om, Neyda [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Escola de Quimica; Cavado, Alberto; Reyes, Yordanka [Centro de Pesquisas do Petroleo, Cidade de Havana (Cuba); Dominguez, Zulema [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE)

2004-07-01

The production of heavy crude oils increased in the last years in the world. Crude oils with high density, viscosity, acidity and sulfur, nitrogen, metals and asphaltenes contents, by the others hand, low stability and low product quality. The challenger of many refiners is find solutions to refine the heavy crude oils, and produce fuels with certify quality, such as Jet Fuel. The principal aviation technique on the world work with gas turbines engines feted for jet fuel (JET A1). The quality specifications of this fuel are establish by International Norms: ASTM-1655, DEF STAN 91-91-3 (DERD 2494) and joint Fuelling System Check List. The world technologies to obtain jet fuel from mixtures of heavy crude oil with middle crude oils are: Atmospheric distillation, with a posterior hydrogenation and finally the additivation. Studies carried out have demonstrates that the Cubans heavy crude oils is characterized for having API less than 10, raised viscosity, high sulfur content (>6%) and asphaltenes content (more than 15%). These properties provide to its derivatives of low quality. This paper define the characteristic of Cuban heavy crude oil, the technology and operational conditions to produce jet fuel (Jet A1) and the quality of fuel produced. (author)

Hydroprocessing Catalysts. Utilization and Regeneration Schemes Catalyseurs d'hydrotraitement. Schémas d'utilisation et de régénération

OpenAIRE

Furimsky E.

2006-01-01

The catalyst reactor inventory represents an important part of the cost of hydroprocessing operation. The selection of a suitable catalyst and reactor is influenced by feedstock properties. Processes ensuring an uninterrupted operation during catalyst addition and withdrawal are preferred for processing high asphaltene and metal content feedstocks. The spent catalyst can be regenerated and returned to the operation if the extent of its deactivation is not high. The regeneration may be perform...

Measurements and thermodynamics of hydrotreater product sludge stability

Energy Technology Data Exchange (ETDEWEB)

Andersen, S.I. [Technical Univ. of Denmark, Lyngby (Denmark)

2003-07-01

Sludge is a by-product of the hydrotreating process of asphaltene during feedstock conversions. The stability of the asphaltenes in the system is related to the produced sludge. The remaining asphaltenes are unstable due to chemical changes in the mixture even though a large conversion of heptane asphaltene occurs. The flocculation titration technique was applied to several feedstocks and catalysts to understand changes in stability and to develop conversion schemes that avoid sludge formation. The effect of temperature conversion was studied in detail. Results obtained by flocculation titration were in agreement with size exclusion chromatography, elemental analysis, infrared spectroscopy and other methods. The authors also examined the chemical changes in product and in product asphaltenes. It was concluded that high hydrotreatment temperature leads to the formation of unstable products as cracking occurs. It was shown that molecular weight of asphaltenes decreases during the hydroprocessing, and the transition temperature is related to the feed. tabs., figs.

First crude oil from Chukotka

Energy Technology Data Exchange (ETDEWEB)

Arenbrister, L.P.; Demidenko, K.A.; Zhmykhova, N.M.

1986-01-01

The physicochemical properties of the crude taken from Neogene deposits at a depth of 1486-1443 m are analyzed. The oil is distinguished by low contents of sulfur and resinous-asphaltenic substances, a high content of wax, and a high yield of light cuts distilling below 350 degrees C. The naptha cuts have high contents of naphthenes, and the diesel fuel cuts have high cetane numbers, low sulfur contents, and high contents of straight chain paraffins. The vacuum gasoil has a low density, a low viscosity, a low carbon residue and low contents of sulfur and nitrogen. This gasoil is a good feedstock for catalytic cracking and hydrocracking. The Verkhne-Echin crude is classified as light, low-sulfur, lowresin and high-wax. It can be used to produce jet fuels and summer-grade diesel fuels with low sulfur contents, as well as high-V.I. lube base stocks and liquid and solid paraffins.

Greater bottoms upgrading with Albemarle's e-bed catalysts

Energy Technology Data Exchange (ETDEWEB)

Toshima, H.; Sedlacek, Z.; Backhouse, D.; Mayo, S.; Plantenga, F. [Albemarle Catalysts, Houston, TX (United States)

2006-07-01

The E-bed process is a heavy oil upgrading technology that produces near isothermal reactor conditions at a constant catalytic activity. However, E-bed conversion optimization is limited by reactor and downstream fouling problems caused by asphaltene precipitation. While asphaltene precipitation can controlled by reducing hydrogenation, high hydrogenation activity is needed for the removal of sulfur and heavy metals. This presentation described an asphaltene molecule management concept to reduce the fouling of E-bed units. Sediment reduction and high hydrogenation catalysts were used in a modified E-bed process with a variety of feeds and operating conditions. It was observed that the KF1312 catalyst achieved much higher sediment-reduction capability along with satisfactory hydrogenation activity with the different kinds of crude oil sources tested. The catalyst hydrocracked the asphaltenes into smaller molecules, which created greater asphaltene solubility. The sediment reduction capacity of the catalyst-staging technology is now being optimized. It was concluded that the technology will help to reduce fouling in E-bed processes and lead to improved conversion rates for refineries. refs., tabs., figs.

A new generation of models for water-in-oil emulsion formation

International Nuclear Information System (INIS)

Fingas, M.

2009-01-01

Water-in-oil emulsions form after oil or petroleum products are spilled, and can make the cleanup of oil spills difficult. This paper discussed new modelling schemes designed for the formation of water-in-oil emulsions. Density, viscosity, asphaltene and resin contents were used to compute a class index for unstable, entrained water-in-oil states, meso-stable, or stable emulsions. Prediction schemes were used to estimate the water content and viscosity of the water-in-oil states and the time to formation with wave height inputs. A numerical values was used for each type of water-in-oil type. The properties of the starting oil were correlated with the numerical scheme. New regressions were then performed using a Gaussian-style regression expansion technique. Data obtained from the models suggested that water-in-oil types are stabilized by both asphaltenes and resins. The optimized model was then compared with earlier models. The study showed that the new model has the capacity to accurately predict oil-in-water types approximately 90 per cent of the time using only resin, saturate, asphaltene, viscosity, and density data. 17 refs., 8 tabs., 8 figs

Petroleum Processing Efficiency Improvement

Energy Technology Data Exchange (ETDEWEB)

John Schabron; Joseph Rovani; Mark Sanderson; Jenny Loveridge

2012-09-01

A series of volatile crude oils was characterized using the Asphaltene Determinator oncolumn precipitation and re-dissolution method developed at Western Research Institute (WRI). Gravimetric asphaltenes and polars fractions from silica gel chromatography separation of the oils were characterized also. A study to define the differences in composition of asphaltenes in refinery desalter rag layer emulsions and the corresponding feed and desalter oils was conducted. Results indicate that the most polar and pericondensed aromatic material in the asphaltenes is enriched in the emulsions. The wax types and carbon number distributions in the two heptaneeluting fractions from the Waxphaltene Determinator separation were characterized by repetitive collection of the fractions followed by high temperature gas chromatography (GC) and Fourier transform infrared spectroscopy (FTIR). High resolution Fourier transform ion cyclotron resonance mass spectrometry (FT-ICRMS) was conducted by researchers at the Florida State University National High Magnetic Field laboratory in a no-cost collaboration with the study.

Water-in-oil emulsions results of formation studies and applicability to oil spill modelling

International Nuclear Information System (INIS)

Fingas, Merv; Fieldhouse, Ben; Mullin, Joe

1999-01-01

This paper summarises studies of water-in-oil emulsions, their stability, and modelling of their formation. Studies show that water-in-oil emulsions might be characterised into three categories (stable, mesostable and unstable). These categories were established by visual appearance, elasticity and viscosity difference. It was also shown that water content was not an important factor. A fourth category of water-in-oil exists, that of water entrainment, which is not an emulsion. Water-in-oil emulsions made from crude oils have different classes of stabilities as a result of the asphaltene and resin contents. The differences in the emulsion types are readily distinguished both by their rheological properties, and simply by appearance. The apparent viscosity of a stable emulsion at a shear rate of one reciprocal second, is at least three orders-of-magnitude greater than the starting oil. An unstable emulsion usually has a viscosity no more than one order-of-magnitude greater than that of the starting oil. A stable emulsion has a significant elasticity, whereas an unstable emulsion does not. Stable emulsions have sufficient asphaltenes (>∼7%) to establish films of these compounds around water droplets. Mesostable emulsions have insufficient asphaltenes to render them completely stable. Stability is achieved by visco-elastic retention of water and secondarily by the presence of asphaltene or resin films. Mesostable emulsions display apparent viscosities of about 80-600 times that of the starting oil and true viscosities of 20-200 times that of the starting oil. Mesostable emulsions have an asphaltene and resin content greater than 3%. Entrained water occurs when a viscous oil retains larger water droplets, but conditions are not suitable for the formation of an emulsion. Entrained water may have a viscosity that is similar or slightly greater (∼ 2-10 times) than the starting oil. It was found that emulsion formation occurs at a threshold energy, however this energy

New sunflower seeds with high contents of phytosterols

Directory of Open Access Journals (Sweden)

Velasco Leonardo

2014-11-01

Full Text Available Dietary phytosterols have a positive nutritional impact because they contribute to reduce cholesterol levels in blood. Accordingly, foods rich in phytosterols are required in a healthy diet. Vegetable oils are the richest source of phytosterols in the diet, though sunflower oil has lower phytosterol content than other seed oils such as rapeseed and corn. Increasing phytosterol content in sunflower oil requires optimizing first selection procedures. In this way, the development of accurate methods for analyzing phytosterol content in seeds instead of oils has opened up recently the way for large-scale screening for this trait. Large variability for seed phytosterol content has been identified in sunflower germplasm, from which we have developed a line, IASP-18, with about twofold seed phytosterol content than conventional sunflower. The trait is expressed across environments. Genetic studies are underway to characterize its inheritance and assess the feasibility of introgressing genes for high phytosterol content into elite sunflower germplasm.

Enhanced biodegradation of asphalt in the presence of Tween surfactants, Mn(2+) and H2O2 by Pestalotiopsis sp. in liquid medium and soil.

Science.gov (United States)

Yanto, Dede Heri Yuli; Tachibana, Sanro

2014-05-01

Asphalt and fractions thereof can contaminate water and soil environments. Forming as residues in distillation products in crude oil refineries, asphalts consist mostly of asphaltene instead of aliphatics, aromatics, and resins. The high asphaltene content might be responsible for the decrease in bioavailability to microorganisms and therefore reduce the biodegradability of asphalt in the environment. In this study, the effect on asphalt biodegradation by Pestalotiopsis sp. in liquid medium and soil of nonionic Tween surfactants in the presence of Mn2+ and H2O2 was examined. The degradation was enhanced by Tween 40 or Tween 80 (0.1%) in the presence of Mn2+ (1 mM) and H2O2 (0.05 mM). A Tween surfactant, Mn2+, and H2O2 can overcome bioavailability-mediated constraints and increase ligninolytic activities, particularly manganese peroxidase and laccase activities. The study is significant for the bioremediation of asphalt and/or viscous-crude oil-contaminated environments. Copyright © 2013 Elsevier Ltd. All rights reserved.

Microbiologically Influenced Corrosion

Science.gov (United States)

2015-11-05

high in water content, are less corrosive owing to their elevated viscosity and resulting low conductivity (᝺-7 S/cm) [30]. Asphaltenes and resins...wet surface to a water-wet surface. Sludge deposits are combinations of hydrocarbons, sand, clay , corTosion prod- ucts, and biomass that can reach 50...fine clay sun·ounded by a film of water. Under low flow conditions, these particles precipitate and form a sludge deposit. 27.4 TESTING 27 .4.1 A

Information management for high content live cell imaging

Directory of Open Access Journals (Sweden)

White Michael RH

2009-07-01

Full Text Available Abstract Background High content live cell imaging experiments are able to track the cellular localisation of labelled proteins in multiple live cells over a time course. Experiments using high content live cell imaging will generate multiple large datasets that are often stored in an ad-hoc manner. This hinders identification of previously gathered data that may be relevant to current analyses. Whilst solutions exist for managing image data, they are primarily concerned with storage and retrieval of the images themselves and not the data derived from the images. There is therefore a requirement for an information management solution that facilitates the indexing of experimental metadata and results of high content live cell imaging experiments. Results We have designed and implemented a data model and information management solution for the data gathered through high content live cell imaging experiments. Many of the experiments to be stored measure the translocation of fluorescently labelled proteins from cytoplasm to nucleus in individual cells. The functionality of this database has been enhanced by the addition of an algorithm that automatically annotates results of these experiments with the timings of translocations and periods of any oscillatory translocations as they are uploaded to the repository. Testing has shown the algorithm to perform well with a variety of previously unseen data. Conclusion Our repository is a fully functional example of how high throughput imaging data may be effectively indexed and managed to address the requirements of end users. By implementing the automated analysis of experimental results, we have provided a clear impetus for individuals to ensure that their data forms part of that which is stored in the repository. Although focused on imaging, the solution provided is sufficiently generic to be applied to other functional proteomics and genomics experiments. The software is available from: fhttp://code.google.com/p/livecellim/

Advances in Predictive Toxicology for Discovery Safety through High Content Screening.

Science.gov (United States)

Persson, Mikael; Hornberg, Jorrit J

2016-12-19

High content screening enables parallel acquisition of multiple molecular and cellular readouts. In particular the predictive toxicology field has progressed from the advances in high content screening, as more refined end points that report on cellular health can be studied in combination, at the single cell level, and in relatively high throughput. Here, we discuss how high content screening has become an essential tool for Discovery Safety, the discipline that integrates safety and toxicology in the drug discovery process to identify and mitigate safety concerns with the aim to design drug candidates with a superior safety profile. In addition to customized mechanistic assays to evaluate target safety, routine screening assays can be applied to identify risk factors for frequently occurring organ toxicities. We discuss the current state of high content screening assays for hepatotoxicity, cardiotoxicity, neurotoxicity, nephrotoxicity, and genotoxicity, including recent developments and current advances.

iScreen: Image-Based High-Content RNAi Screening Analysis Tools.

Science.gov (United States)

Zhong, Rui; Dong, Xiaonan; Levine, Beth; Xie, Yang; Xiao, Guanghua

2015-09-01

High-throughput RNA interference (RNAi) screening has opened up a path to investigating functional genomics in a genome-wide pattern. However, such studies are often restricted to assays that have a single readout format. Recently, advanced image technologies have been coupled with high-throughput RNAi screening to develop high-content screening, in which one or more cell image(s), instead of a single readout, were generated from each well. This image-based high-content screening technology has led to genome-wide functional annotation in a wider spectrum of biological research studies, as well as in drug and target discovery, so that complex cellular phenotypes can be measured in a multiparametric format. Despite these advances, data analysis and visualization tools are still largely lacking for these types of experiments. Therefore, we developed iScreen (image-Based High-content RNAi Screening Analysis Tool), an R package for the statistical modeling and visualization of image-based high-content RNAi screening. Two case studies were used to demonstrate the capability and efficiency of the iScreen package. iScreen is available for download on CRAN (http://cran.cnr.berkeley.edu/web/packages/iScreen/index.html). The user manual is also available as a supplementary document. © 2014 Society for Laboratory Automation and Screening.

About Coloured Cold Asphaltic Mixtures

Directory of Open Access Journals (Sweden)

Loredana Judele

2008-01-01

Full Text Available The first coloured bitumen was obtained by using bitumen from Peru and then bitumen from the Middle East, with a low content of asphaltenes, also called "colourable" bitumens. The colours obtained by adding iron oxides led nevertheless to dark colours, due to the presence of asphaltenes. Nowadays the coloured asphalt is obtained from synthesis binders with translucent aspect. The colours are obtained by adding inorganic pigments, mainly iron oxide for red, chromic oxide for green, titanic dioxide for white. The properties and behaviour of the coloured bitumen during its lifetime are comparable with the ones of classic bitumen, sometimes even better.

High Content Screening: Understanding Cellular Pathway

International Nuclear Information System (INIS)

Mohamed Zaffar Ali Mohamed Amiroudine; Daryl Jesus Arapoc; Zainah Adam; Shafii Khamis

2015-01-01

High content screening (HCS) is the convergence between cell-based assays, high-resolution fluorescence imaging, phase-contrast imaging of fixed- or live-cell assays, tissues and small organisms. It has been widely adopted in the pharmaceutical and biotech industries for target identification and validation and as secondary screens to reveal potential toxicities or to elucidate a drugs mechanism of action. By using the ImageXpress® Micro XLS System HCS, the complex network of key players controlling proliferation and apoptosis can be reduced to several sentinel markers for analysis. Cell proliferation and apoptosis are two key areas in cell biology and drug discovery research. Understanding the signaling pathways in cell proliferation and apoptosis is important for new therapeutic discovery because the imbalance between these two events is predominant in the progression of many human diseases, including cancer. The DNA binding dye DAPI is used to determine the nuclear size and nuclear morphology as well as cell cycle phases by DNA content. Images together with MetaXpress® analysis results provide a convenient and easy to use solution to high volume image management. In particular, HCS platform is beginning to have an important impact on early drug discovery, basic research in systems cell biology, and is expected to play a role in personalized medicine or revealing off-target drug effects. (author)

Shedding Light on Filovirus Infection with High-Content Imaging

Directory of Open Access Journals (Sweden)

Rekha G. Panchal

2012-08-01

Full Text Available Microscopy has been instrumental in the discovery and characterization of microorganisms. Major advances in high-throughput fluorescence microscopy and automated, high-content image analysis tools are paving the way to the systematic and quantitative study of the molecular properties of cellular systems, both at the population and at the single-cell level. High-Content Imaging (HCI has been used to characterize host-virus interactions in genome-wide reverse genetic screens and to identify novel cellular factors implicated in the binding, entry, replication and egress of several pathogenic viruses. Here we present an overview of the most significant applications of HCI in the context of the cell biology of filovirus infection. HCI assays have been recently implemented to quantitatively study filoviruses in cell culture, employing either infectious viruses in a BSL-4 environment or surrogate genetic systems in a BSL-2 environment. These assays are becoming instrumental for small molecule and siRNA screens aimed at the discovery of both cellular therapeutic targets and of compounds with anti-viral properties. We discuss the current practical constraints limiting the implementation of high-throughput biology in a BSL-4 environment, and propose possible solutions to safely perform high-content, high-throughput filovirus infection assays. Finally, we discuss possible novel applications of HCI in the context of filovirus research with particular emphasis on the identification of possible cellular biomarkers of virus infection.

Polymer science applied to petroleum production; Ciencia de polimeros aplicada a producao de petroleo

Energy Technology Data Exchange (ETDEWEB)

Lucas, Elizabete F.; Mansur, Claudia R.E.; Garreto, Maria S.E.; Honse, Siller O.; Mazzeo, Claudia P.P. [Universidade Federal do Rio de Janeiro/ Instituto de Macromoleculas/ Laboratorio de Macromoleculas e Coloides na Industria de Petroleo, Rio de Janeiro, RJ (Brazil)], e-mail: elucas@ima.ufrj.br

2011-07-01

The petroleum production comprises several operations, from well drilling to oil and water treatment, in which polymer science is applied. This work is focused in the phase behavior of asphaltenes that can be evaluated by precipitation tests and particle size determination. Recent researches show that the petroleum can be diluted with a specific model solvent, without causing any changes on asphaltenes phase behavior, and that a representative model system can be obtained if asphaltenes could be extracted using n-alkane as low as C1. The phase behavior of asphaltenes directly depends on the solubility parameter, which can be estimated for petroleum and asphaltenic fractions by microcalorimetry. More polar asphaltenes are not completely stabilized by less polar molecules, and this affects the stability of the A/O emulsions. There is a relationship between the amount of polar groups in the polymer chain and its capability in stabilizing/flocculating the asphaltenes, which interferes in the asphaltenes particle sizes. (author)

Liquid alternative diesel fuels with high hydrogen content

Energy Technology Data Exchange (ETDEWEB)

Hancsok, Jenoe; Varga, Zoltan; Eller, Zoltan; Poelczmann, Gyoergy [Pannonia Univ., Veszprem (Hungary). MOL Dept. of Hydrocarbon Processing; Kasza, Tamas [MOL Hungarian Oil and Gas Plc., Szazhalombatta (Hungary)

2013-06-01

Mobility is a keystone of the sustainable development. In the operation of the vehicles as the tools of mobility internal combustion engines, so thus Diesel engines will play a remarkable role in the next decades. Beside fossil fuels - used for power these engines - liquid alternative fuels have higher and higher importance, because of their known advantages. During the presentation the categorization possibilities based on the chronology of their development and application will be presented. The importance of fuels with high hydrogen content will be reviewed. Research and development activity in the field of such kind of fuels will be presented. During this developed catalytic systems and main performance properties of the product will be presented which were obtained in case of biogasoils produced by special hydrocracking of natural triglycerides and in case of necessity followed by isomerization; furthermore in case of synthetic biogasoils obtained by the isomerization hydrocracking of Fischer-Tropsch paraffins produced from biomass based synthesis gas. Excellent combustion properties (cetane number > 65-75), good cold flow properties and reduced harmful material emission due to the high hydrogen content (C{sub n}H{sub 2n+2}) are highlighted. Finally production possibilities of linear and branched paraffins based on lignocelluloses are briefly reviewed. Summarizing it was concluded that liquid hydrocarbons with high isoparaffin content are the most suitable fuels regarding availability, economical and environmental aspects, namely the sustainable development. (orig.)

Photometric determination of niobium in materials with high content of phosphorus

International Nuclear Information System (INIS)

Navrotskaya, V.A.; Aleksandrova, E.I.; Kletenik, Yu.B.

1982-01-01

To determine niobium in various samples of niobium concentrates with a high phosphorus content, a photometric method with pyridylazoresorcinol (PAR) is used. It is shown that all the elements indicated (Fe, Si, Ti, Al, Ca) including phosphorus do not interfere with the niobium determination with the use of PAR. The method has been tried on artificial samples with different content of the base components. Variation coefficient constitutes 4.5%. No systematic errors, due to a high content of any concomitant element, are detected. The determination threshold is 10 - 2 %

Development of automatic image analysis methods for high-throughput and high-content screening

NARCIS (Netherlands)

Di, Zi

2013-01-01

This thesis focuses on the development of image analysis methods for ultra-high content analysis of high-throughput screens where cellular phenotype responses to various genetic or chemical perturbations that are under investigation. Our primary goal is to deliver efficient and robust image analysis

High-content screening of yeast mutant libraries by shotgun lipidomics

DEFF Research Database (Denmark)

Tarasov, Kirill; Stefanko, Adam; Casanovas, Albert

2014-01-01

To identify proteins with a functional role in lipid metabolism and homeostasis we designed a high-throughput platform for high-content lipidomic screening of yeast mutant libraries. To this end, we combined culturing and lipid extraction in 96-well format, automated direct infusion...... factor KAR4 precipitated distinct lipid metabolic phenotypes. These results demonstrate that the high-throughput shotgun lipidomics platform is a valid and complementary proxy for high-content screening of yeast mutant libraries....... nanoelectrospray ionization, high-resolution Orbitrap mass spectrometry, and a dedicated data processing framework to support lipid phenotyping across hundreds of Saccharomyces cerevisiae mutants. Our novel approach revealed that the absence of genes with unknown function YBR141C and YJR015W, and the transcription...

Study of the interface solid/solutions containing PEO-PPO block copolymers and asphaltenes by FTIR/ATR; Estudo de solucoes de copolimeros em bloco de PEO-PPO contendo asfaltenos por FTIR/DTA

Energy Technology Data Exchange (ETDEWEB)

Aguiar, Janaina I.S.; Neto, Jessica S.G.; Mansur, Claudia R.E. [Universidade Federal do Rio de Janeiro, Instituto de Macromoleculas, Laboratorio de Macromoleculas e Coloides na Industria de Petroleo, Rio de Janeiro, RJ (Brazil)], E-mails: janaina_333@hotmail.com, kinha_dac_dm@hotmail.com; celias@ima.ufrj.br

2011-07-01

The formation of water/oil emulsions can cause problems in various stages of production, processing and refining of petroleum. In this study, the technique of Fourier transform infrared spectroscopy (FTIR) using the method of attenuated total reflectance (ATR) was applied to study the solid-solutions of block copolymers based on poly(ethylene oxide)-poly(propylene oxide) (PEO-PPO) interface and its interaction in this interface with asphaltenic fractions of petroleum. The solid is the crystal of the ATR. Initially, we determined the critical micelle concentration values of the copolymers, which were consistent those obtained by a tensiometer. Bottle Test was also performed to correlate the efficiency of PEO-PPO copolymers in the breaking of water/oil emulsions with its adsorption at the interfaces solutions. (author)

Characterization of the rheological behavior of heavy crude oils for the optimization of their transport; Caracterisation du comportement rheologique des bruts lourds en vue de l'optimisation de leur transport

Energy Technology Data Exchange (ETDEWEB)

Coustet Pierre, C.

2003-10-01

Despite their huge reserves, production of heavy crude oils remains weak, partially because of the high viscosity. This work aims to understand the origin of this viscosity in a view of diminishing In this context, we performed structural (SAXS) and rheological studies (under shearing and oscillatory regime) in order to link macroscopic and microscopic properties of heavy oils. investigated the effect of asphaltenes and resins which are the two most polar and the high molecular mass components of heavy oils. Most of the literature work performed measures organic solvents which are considered as model solvents in a first assumption. These media haw structure too simple compared to oils. That is why we decided to complete this work by experiments in the crude. We shed some light on asphaltenes described as colloidal particles with fractal dimension of 2. Their overlapping, due to numerous polar and hydrogen bonds, responsible for the high viscosity. The contribution of asphaltenes on viscosity is lowered by resins who are able to dissociate aggregates and to reduce the interactions, so to diminish the overlapping The kinetics of formation of bonds involved in asphaltenes overlapping are strongly slower at low temperatures, which implies a shear thinning behavior under sufficiently high shearing. This allow us to describe the crude as a transient network of fractal aggregates. (author)

Evaluation of the characteristics of high burnup and high plutonium content mixed oxide (MOX) fuel

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-08-15

Two kinds of MOX fuel irradiation tests, i.e., MOX irradiation test up to high burnup and MOX having high plutonium content irradiation test, have been performed from JFY 2007 for five years in order to establish technical data concerning MOX fuel behavior during irradiation, which shall be needed in safety regulation of MOX fuel with high reliability. The high burnup MOX irradiation test consists of irradiation extension and post irradiation examination (PIE). The activities done in JFY 2011 are destructive post irradiation examination (D-PIE) such as EPMA and SIMS at CEA (Commissariat a l'Enegie Atomique) facility. Cadarache and PIE data analysis. In the frame of irradiation test of high plutonium content MOX fuel programme, MOX fuel rods with about 14wt % Pu content are being irradiated at BR-2 reactor and corresponding PIE is also being done at PIE facility (SCK/CEN: Studiecentrum voor Kernenergie/Centre d'Etude l'Energie Nucleaire) in Belgium. The activities done in JFY 2011 are non-destructive post irradiation examination (ND-PIE) and D-PIE and PIE data analysis. In this report the results of EPMA and SIMS with high burnup irradiation test and the result of gamma spectrometry measurement which can give FP gas release rate are reported. (author)

Infilling Direction and Fluid Communication in the E2.0 Reservoir of ...

African Journals Online (AJOL)

The study reveals a close similarity in percentage contents of the saturates, aromatics, resins and asphaltenes in all the oils. The maturity gradient clearly shows a maturation trend in the Southwest-Northeast direction which indicates that subsequent charge from the oil kitchen were more mature than the initial charges.

High content screening in microfluidic devices

Science.gov (United States)

Cheong, Raymond; Paliwal, Saurabh; Levchenko, Andre

2011-01-01

Importance of the field Miniaturization is key to advancing the state-of-the-art in high content screening (HCS), in order to enable dramatic cost savings through reduced usage of expensive biochemical reagents and to enable large-scale screening on primary cells. Microfluidic technology offers the potential to enable HCS to be performed with an unprecedented degree of miniaturization. Areas covered in this review This perspective highlights a real-world example from the authors’ work of HCS assays implemented in a highly miniaturized microfluidic format. Advantages of this technology are discussed, including cost savings, high throughput screening on primary cells, improved accuracy, the ability to study complex time-varying stimuli, and ease of automation, integration, and scaling. What the reader will gain The reader will understand the capabilities of a new microfluidics-based platform for HCS, and the advantages it provides over conventional plate-based HCS. Take home message Microfluidics technology will drive significant advancements and broader usage and applicability of HCS in drug discovery. PMID:21852997

Active Learning Strategies for Phenotypic Profiling of High-Content Screens.

Science.gov (United States)

Smith, Kevin; Horvath, Peter

2014-06-01

High-content screening is a powerful method to discover new drugs and carry out basic biological research. Increasingly, high-content screens have come to rely on supervised machine learning (SML) to perform automatic phenotypic classification as an essential step of the analysis. However, this comes at a cost, namely, the labeled examples required to train the predictive model. Classification performance increases with the number of labeled examples, and because labeling examples demands time from an expert, the training process represents a significant time investment. Active learning strategies attempt to overcome this bottleneck by presenting the most relevant examples to the annotator, thereby achieving high accuracy while minimizing the cost of obtaining labeled data. In this article, we investigate the impact of active learning on single-cell-based phenotype recognition, using data from three large-scale RNA interference high-content screens representing diverse phenotypic profiling problems. We consider several combinations of active learning strategies and popular SML methods. Our results show that active learning significantly reduces the time cost and can be used to reveal the same phenotypic targets identified using SML. We also identify combinations of active learning strategies and SML methods which perform better than others on the phenotypic profiling problems we studied. © 2014 Society for Laboratory Automation and Screening.

High oleic acid content materials of rapeseed (Brassica napus) produced by radiation breeding

International Nuclear Information System (INIS)

Guan Chunyun; Liu Chunlin; Chen Sheyuan

2006-01-01

High oleic acid content rapeseed breeding has great significance, because high oleic acid oil is a healthy and nutritious oil, which is of a long shelflife and also propitious to producing biodiesel fuel. The high oleic acid content breeding materials of rapeseed (B. napus) were obtained by 80-100 kR ~(60)Co gamma ray ionizing radiation treatment of dry seeds and continuous selection. The results showed that the oleic acid contents of M (2), M (3) and M (4) progenies increased by different grades. Moreover, the oleic acid content of M (5) progeny increased greatly. The oleic acid contents were higher than 70% in the most of the plants and the highest one reached 93.5 %. The base G was transited by base A in fad (2) gene at the 270 site of high oleic acid mutation (M(6) 04-855). The location is at the beta folding area and conservative area of this protein. Base mutation at sites 1 044 and 1 062 also led to produce a stop condon. These changes in structure led to loss the function of fad (2). According to molecular mechanism of gene mutation, no matter what transvertion or transition happens, several replications are needed. That is to say several generations are needed. That was also the reason why high oleic acid content mutation occurred in later generations

The aluminium content of infant formulas remains too high.

Science.gov (United States)

Chuchu, Nancy; Patel, Bhavini; Sebastian, Blaise; Exley, Christopher

2013-10-08

Recent research published in this journal highlighted the issue of the high content of aluminium in infant formulas. The expectation was that the findings would serve as a catalyst for manufacturers to address a significant problem of these, often necessary, components of infant nutrition. It is critically important that parents and other users have confidence in the safety of infant formulas and that they have reliable information to use in choosing a product with a lower content of aluminium. Herein, we have significantly extended the scope of the previous research and the aluminium content of 30 of the most widely available and often used infant formulas has been measured. Both ready-to-drink milks and milk powders were subjected to microwave digestion in the presence of 15.8 M HNO3 and 30% w/v H2O2 and the aluminium content of the digests was measured by TH GFAAS. Both ready-to-drink milks and milk powders were contaminated with aluminium. The concentration of aluminium across all milk products ranged from ca 100 to 430 μg/L. The concentration of aluminium in two soya-based milk products was 656 and 756 μg/L. The intake of aluminium from non-soya-based infant formulas varied from ca 100 to 300 μg per day. For soya-based milks it could be as high as 700 μg per day. All 30 infant formulas were contaminated with aluminium. There was no clear evidence that subsequent to the problem of aluminium being highlighted in a previous publication in this journal that contamination had been addressed and reduced. It is the opinion of the authors that regulatory and other non-voluntary methods are now required to reduce the aluminium content of infant formulas and thereby protect infants from chronic exposure to dietary aluminium.

Deasphalting solvents

International Nuclear Information System (INIS)

Carrillo, J. A; Caceres, J; Vela, G; Bueno, H

1996-01-01

This paper describes how the deasphalted oil (DMO) or demetalized oil (DMO) quality (CCR, Ni, V end asphaltenes contents) changes with: DAO or DMO yield, solvent/feed ratio, type of vacuum reside (from paraffinic to blends with vis breaking bottoms), extraction temperature and extraction solvent (propane, propylene, n-butane and I butane)

Représentation chimique de la structure des kérogènes et des asphaltènes en fonction de leur origine et de leur degré d'évolution Chemical Modeling of the Structure of Kerogens and Asphaltenes As a Function of Their Origin and Evolution Stage

Directory of Open Access Journals (Sweden)

Behar F.

2006-11-01

Full Text Available Dans cet article nous proposons des modèles de structures chimiques de kérogènes et d'asphaltènes de roche. Nous avons choisi de représenter les kérogènes appartenant aux trois types classiques de matières organiques aux stades d'évolution suivants : - début de la diagenèse sensu-stricto; - début de la catagenèse (formation de l'huile; - fin de la catagenèse (formation du gaz. Les asphaltènes représentés correspondent à la phase de formation de l'huile. Nous avons tenu compte des données d'analyse obtenues sur des échantillons naturels : analyse élémentaire, microscopie électronique, RMN 13C, thermogravimétrie, analyse fonctionnelle, dégradation par pyrolyse. Afin d'obtenir une représentation chimique ayant une valeur statistique suffisante, nous avons choisi une masse moléculaire de 25 000 environ, identique pour les trois kérogènes au début de la diagenèse, et une masse de 8000 environ pour les asphaltènes associés. Nous avons ensuite dessiné à l'échelle moléculaire les structures correspondantes. This paper proposes models for the chemical structures of kerogens and asphaltenes from rocks. The kerogens belonging to the three conventional types of organic matter are represented in the following stages of evolution: (1 beginning of diagenesis sensu stricto,(2 beginning of catagenesis (formation of oil, and (3 end of catagenesis (formation of gas. The asphaltenes represented here correspond to the phase of oil formation. Models are based on analytical data obtained on natural samples, i. e. elemental analysis, electron microscopy, 13C NMR, thermogravimetry, functional analysis and pyrolysis. To get enough statistical value for the chemical modelling, a same molecular mass of about 25 000 was chosen for the three kerogens at the beginning of diagenesis. A molecular mass of about 8000 was chosen for the related asphaltenes. The chemical structures were then constructed at the molecular scale.

Fe-based bulk amorphous alloys with iron contents as high as 82 at%

Energy Technology Data Exchange (ETDEWEB)

Li, Jin-Feng; Liu, Xue; Zhao, Shao-Fan; Ding, Hong-Yu [School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Yao, Ke-Fu, E-mail: kfyao@tsinghua.edu.cn [School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China)

2015-07-15

Fe-based bulk amorphous alloys (BAAs) with high Fe contents are advantageous due to their high saturation magnetization and low cost. However, preparing Fe-based BAAs with Fe contents higher than 80 at% is difficult due to their poor glass forming abilities (GFA). In this study, an Fe{sub 81}P{sub 8.5}C{sub 5.5}B{sub 2}Si{sub 3} BAA with a diameter of 1 mm and a saturation magnetization of 1.56 T was successfully prepared using the fluxing and copper mold casting methods. In addition, by introducing a small amount of elemental Mo to the alloy, an Fe{sub 82}Mo{sub 1}P{sub 6.5}C{sub 5.5}B{sub 2}Si{sub 3} BAA rod with a diameter of 1 mm, a high saturation magnetization of 1.59 T, a high yield stress of 3265 MPa, and a clear plasticity of 1.3% was prepared in the same way. The cost effectiveness and good magnetic properties of these newly-developed Fe-based BAAs with Fe contents as high as 82 at% would be advantageous and promising for industrial applications. - Highlights: • Novel Fe-based BAA with no other metallic element except 81 at% Fe was prepared. • Fe-based bulk amorphous alloy (BAA) with the highest Fe content (82%) was prepared. • Very high saturation magnetization of 1.59 T has been achieved. • A new thought for designing Fe-based BAA with high Fe content was provided.

Localization-based super-resolution imaging meets high-content screening.

Science.gov (United States)

Beghin, Anne; Kechkar, Adel; Butler, Corey; Levet, Florian; Cabillic, Marine; Rossier, Olivier; Giannone, Gregory; Galland, Rémi; Choquet, Daniel; Sibarita, Jean-Baptiste

2017-12-01

Single-molecule localization microscopy techniques have proven to be essential tools for quantitatively monitoring biological processes at unprecedented spatial resolution. However, these techniques are very low throughput and are not yet compatible with fully automated, multiparametric cellular assays. This shortcoming is primarily due to the huge amount of data generated during imaging and the lack of software for automation and dedicated data mining. We describe an automated quantitative single-molecule-based super-resolution methodology that operates in standard multiwell plates and uses analysis based on high-content screening and data-mining software. The workflow is compatible with fixed- and live-cell imaging and allows extraction of quantitative data like fluorophore photophysics, protein clustering or dynamic behavior of biomolecules. We demonstrate that the method is compatible with high-content screening using 3D dSTORM and DNA-PAINT based super-resolution microscopy as well as single-particle tracking.

Induced mutations in wheat, Triticum aestivum L., for high protein and lysine content

International Nuclear Information System (INIS)

Barriga, P.; Fuentes, R.

1984-01-01

With the aim of producing cultivars adapted to the Lakes Region of Chile (latitude 39-44 deg. South) with better protein content and high grain yield, in 1975 spring wheat seeds of genotypes Express and UACH-2-75 were irradiated with gamma rays in doses of 15, 25 and 35 Krad. The M 1 generation was field sown and harvested individually, initiating plant selection in the M 2 generation. The selection process, through six generations, has permitted to identify some mutants of high protein content. Two mutants UACH-2-I and UACH-3-I have been included in the National Co-operative Wheat Program for yield. A second experiment was initiated in 1981 with the objective of obtaining mutants not only for high protein content but also for high lysine content. For this purpose seeds of the spring wheat genotypes Huenufen and Austral were irradiated with gamma rays in doses of 10 and 25 Krad. The M 1 generation was sown at a high density and harvested in bulk. Selection per plant will start in the M 2 generation, continuing in the following. (author)

High-performance membrane-electrode assembly with an optimal polytetrafluoroethylene content for high-temperature polymer electrolyte membrane fuel cells

DEFF Research Database (Denmark)

Jeong, Gisu; Kim, MinJoong; Han, Junyoung

2016-01-01

Although high-temperature polymer electrolyte membrane fuel cells (HT-PEMFCs) have a high carbon monoxide tolerance and allow for efficient water management, their practical applications are limited due to their lower performance than conventional low-temperature PEMFCs. Herein, we present a high......-performance membrane-electrode assembly (MEA) with an optimal polytetrafluoroethylene (PTFE) content for HT-PEMFCs. Low or excess PTFE content in the electrode leads to an inefficient electrolyte distribution or severe catalyst agglomeration, respectively, which hinder the formation of triple phase boundaries...

Oxy-combustion of high water content fuels

Science.gov (United States)

Yi, Fei

As the issues of global warming and the energy crisis arouse extensive concern, more and more research is focused on maximizing energy efficiency and capturing CO2 in power generation. To achieve this, in this research, we propose an unconventional concept of combustion - direct combustion of high water content fuels. Due to the high water content in the fuels, they may not burn under air-fired conditions. Therefore, oxy-combustion is applied. Three applications of this concept in power generation are proposed - direct steam generation for the turbine cycle, staged oxy-combustion with zero flue gas recycle, and oxy-combustion in a low speed diesel-type engine. The proposed processes could provide alternative approaches to directly utilize fuels which intrinsically have high water content. A large amount of energy to remove the water, when the fuels are utilized in a conventional approach, is saved. The properties and difficulty in dewatering high water content fuels (e.g. bioethanol, microalgae and fine coal) are summarized. These fuels include both renewable and fossil fuels. In addition, the technique can also allow for low-cost carbon capture due to oxy-combustion. When renewable fuel is utilized, the whole process can be carbon negative. To validate and evaluate this concept, the research focused on the investigation of the flame stability and characteristics for high water content fuels. My study has demonstrated the feasibility of burning fuels that have been heavily diluted with water in a swirl-stabilized burner. Ethanol and 1-propanol were first tested as the fuels and the flame stability maps were obtained. Flame stability, as characterized by the blow-off limit -- the lowest O2 concentration when a flame could exist under a given oxidizer flow rate, was determined as a function of total oxidizer flow rate, fuel concentration and nozzle type. Furthermore, both the gas temperature contour and the overall ethanol concentration in the droplets along the

Denuded zone in Czochralski silicon wafer with high carbon content

International Nuclear Information System (INIS)

Chen Jiahe; Yang Deren; Ma Xiangyang; Que Duanlin

2006-01-01

The thermal stability of the denuded zone (DZ) created by high-low-high-temperature annealing in high carbon content (H[C]) and low carbon content (L[C]) Czochralski silicon (Cz-Si) has been investigated in a subsequent ramping and isothermal 1050 deg. C annealing. The tiny oxygen precipitates which might occur in the DZ were checked. It was found in the L[C] Cz-Si that the DZ shrank and the density of bulk micro-defects (BMDs) reduced with the increase of time spent at 1050 deg. C. Also, the DZs above 15 μm of thickness present in the H[C] Cz-Si wafers continuously and the density and total volume of BMDs first decreased then increased and finally decreased again during the treatments. Moreover, tiny oxygen precipitates were hardly generated inside the DZs, indicating that H[C] Cz-Si wafers could support the fabrication of integrated circuits

Denuded zone in Czochralski silicon wafer with high carbon content

Science.gov (United States)

Chen, Jiahe; Yang, Deren; Ma, Xiangyang; Que, Duanlin

2006-12-01

The thermal stability of the denuded zone (DZ) created by high-low-high-temperature annealing in high carbon content (H[C]) and low carbon content (L[C]) Czochralski silicon (Cz-Si) has been investigated in a subsequent ramping and isothermal 1050 °C annealing. The tiny oxygen precipitates which might occur in the DZ were checked. It was found in the L[C] Cz-Si that the DZ shrank and the density of bulk micro-defects (BMDs) reduced with the increase of time spent at 1050 °C. Also, the DZs above 15 µm of thickness present in the H[C] Cz-Si wafers continuously and the density and total volume of BMDs first decreased then increased and finally decreased again during the treatments. Moreover, tiny oxygen precipitates were hardly generated inside the DZs, indicating that H[C] Cz-Si wafers could support the fabrication of integrated circuits.

Method for creating high carbon content products from biomass oil

Science.gov (United States)

Parker, Reginald; Seames, Wayne

2012-12-18

In a method for producing high carbon content products from biomass, a biomass oil is added to a cracking reactor vessel. The biomass oil is heated to a temperature ranging from about 100.degree. C. to about 800.degree. C. at a pressure ranging from about vacuum conditions to about 20,700 kPa for a time sufficient to crack the biomass oil. Tar is separated from the cracked biomass oil. The tar is heated to a temperature ranging from about 200.degree. C. to about 1500.degree. C. at a pressure ranging from about vacuum conditions to about 20,700 kPa for a time sufficient to reduce the tar to a high carbon content product containing at least about 50% carbon by weight.

Chemical modification of bitumen heavy ends and their non-fuel uses

Energy Technology Data Exchange (ETDEWEB)

Moschopedis, S.E.; Speight, J.G.

1976-01-01

Bitumen asphaltenes undergo a variety of simple chemical conversions. For example, asphaltenes can be oxidized, sulfonated, sulfomethylated, halogenated, and phosphorylated. The net result is the introduction of functional entities into the asphaltene structure which confers interesting properties on the products for which a variety of uses are proposed.

Residency of rhenium and osmium in a heavy crude oil

Science.gov (United States)

DiMarzio, Jenna M.; Georgiev, Svetoslav V.; Stein, Holly J.; Hannah, Judith L.

2018-01-01

Rhenium-osmium (Re-Os) isotope geochemistry is an emerging tool for the study of oil formation and migration processes, and a new technology for petroleum exploration. Little is known, however, about the residency of Re and Os within asphaltene and maltene sub-fractions of crude oil. This information is crucial for understanding the 187Re-187Os radiometric clock held in petroleum systems and for interpreting geochronology for key processes such as oil formation, migration, and biodegradation. In this study, a heavy crude oil was separated into soluble (maltene, MALT) and insoluble (asphaltene, ASPH) fractions using n-heptane as the asphaltene-precipitating agent. The asphaltenes were separated sequentially into sub-fractions using two different solvent pairs (heptane-dichloromethane and acetone-toluene), and the bulk maltenes were separated into saturate, aromatic, and resin (SAR) fractions using open column chromatography. Each asphaltene and maltene sub-fraction was analyzed for Re and Os. The asphaltene sub-fractions and the bulk ASPH, MALT, and crude oil were analyzed for a suite of trace metals by ICP-MS. Our results show that Re and Os concentrations co-vary between the asphaltene sub-fractions, and that both elements are found mostly in the more polar and aromatic sub-fractions. Significant Re and Os are also present in the aromatic and resin fractions of the maltenes. However, each asphaltene and maltene sub-fraction has a distinct isotopic composition, and sub-fractions are not isochronous. This suggests that asphaltene sub-fractionation separates Re-Os complexes to the point where the isotopic integrity of the geochronometer is compromised. The mobility of individual Re and Os isotopes and the decoupling possibilities between radiogenic 187Os produced from 187Re remain elusive, but their recognition in this study is a critical first step. Re and Os correlate strongly with Mo and Cd in the asphaltene sub-fractions, suggesting that these metals occupy

High content analysis of phagocytic activity and cell morphology with PuntoMorph

DEFF Research Database (Denmark)

Al-Ali, Hassan; Gao, Han; Dalby-Hansen, Camilla

2017-01-01

methods for quantifying phagocytic activity in multiple dimensions including speed, accuracy, and resolution. Conclusions We provide a framework to facilitate the development of high content assays suitable for drug screening. For convenience, we implemented our algorithm in a standalone software package...... with image-based quantification of phagocytic activity. New method We present a robust algorithm and cell-based assay system for high content analysis of phagocytic activity. The method utilizes fluorescently labeled beads as a phagocytic substrate with defined physical properties. The algorithm employs...... content screening. Results We tested our assay system using microglial cultures. Our results recapitulated previous findings on the effects of microglial stimulation on cell morphology and phagocytic activity. Moreover, our cell-level analysis revealed that the two phenotypes associated with microglial...

Auto Detection For High Level Water Content For Oil Well

Science.gov (United States)

Janier, Josefina Barnachea; Jumaludin, Zainul Arifin B.

2010-06-01

Auto detection of high level water content for oil well is a system that measures the percentage of water in crude oil. This paper aims to discuss an auto detection system for measuring the content of water level in crude oil which is applicable for offshore and onshore oil operations. Data regarding water level content from wells can be determined by using automation thus, well with high water level can be determined immediately whether to be closed or not from operations. Theoretically the system measures the percentage of two- fluid mixture where the fluids have different electrical conductivities which are water and crude oil. The system made use of grid sensor which is a grid pattern like of horizontal and vertical wires. When water occupies the space at the intersection of vertical and horizontal wires, an electrical signal is detected which proved that water completed the circuit path in the system. The electrical signals are counted whereas the percentage of water is determined from the total electrical signals detected over electrical signals provided. Simulation of the system using the MultiSIM showed that the system provided the desired result.

Kinethical Aspects of High Solid Contents Copoly(Styrene/Butylacrylate-Cloisite 30B Nanocomposites

Directory of Open Access Journals (Sweden)

M. Mirzataheri

2014-01-01

Full Text Available High solid content poly (styrene-co-butyl acrylate latex ( with 20% and 40% solid content including high amounts of Cloisite 30B (7 wt% and 10 wt% were kinetically investigated. Gravimetric method via measuring the rate of polymerization, number of particles and average number of radicals per particle was used. Results showed that by increasing the solid content; the average diameter of polymer particles decreased. Studies on the polymerization rate depict that the increase in polymer particle size provides more average reactive radicals per polymer particle, which increased from 0.48 to 0.88 for the sample containing 7 wt% clay and 20 wt% solid content. Observed armored particles with honeycomb morphology is the most novelty of this research work, which is suitable for making barrier packaging films.

Production of microbial oil with high oleic acid content by Trichosporon capitatum

Energy Technology Data Exchange (ETDEWEB)

Wu, Hong; Zong, Minhua [State Key Laboratory of Pulp and Paper Engineering, College of Light Industry and Food Sciences, South China University of Technology, Guangzhou 510640 (China); Li, Yuanyuan; Chen, Lei [School of Biosciences and Bioengineering, South China University of Technology, Guangzhou 510640 (China)

2011-01-15

Microbial oils with high unsaturated fatty acids content, especially oleic acid content, are good feedstock for high quality biodiesel production. Trichosporon capitatum was found to accumulate lipid with around 80% oleic acid and 89% total unsaturated fatty acids content on nitrogen-limited medium. In order to improve its lipid yield, effects of medium components and culture conditions on cell growth and lipid accumulation were investigated. Optimization of media resulted in a 61% increase in the lipid yield of T. capitatum after cultivation at 28 C and 160 rpm for 6 days. In addition, T. capitatum could grow well on cane molasses and afford a lipid yield comparable to that on synthetic nitrogen-limited medium. The biodiesel from the microbial oil produced by T. capitatum on cane molasses displayed a low cold filter plugging point (-15 C), and so T. capitatum might be a promising strain to provide lipid suitable for high quality biodiesel production. (author)

Enzymatic pre-treatment of high content cellulosic feedstock improves biogas production

Science.gov (United States)

Animal wastes with high lignin and cellulosic contents can serve as the feedstock for biogas production (mainly methane) that could be used as alternative energy source. However, these high lignin and cellulosic feedstocks are quite recalcitrant to be readily utilized by methanogens to produce ben...

The effect of manganese content on mechanical properties of high titanium microalloyed steels

Energy Technology Data Exchange (ETDEWEB)

Li, Xiaolin, E-mail: lixiaolinwork@163.com [Shougang Research Institute of Technology, Beijing 100041 (China); Li, Fei; Cui, Yang; Xiao, Baoliang [Shougang Research Institute of Technology, Beijing 100041 (China); Wang, Xuemin [School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083 (China)

2016-11-20

In this work, in order to achieve an optimum combination of high strength, ductility and toughness of high Ti microalloyed steel, extensive research efforts were exerted to study the effect of soaking temperature, manganese and sulfur content on properties of titanium steels. Precipitation hardening of Ti-bearing steels has been found to vary with different soaking temperature. Higher strength was achieved in these steels at higher soaking temperature due to dissolution of more TiC, Ti{sub 4}S{sub 2}C{sub 2} and little TiN, which lead to re-precipitation of fine carbides with greater volume fraction. The results of transmission electron microscope (TEM)analysis indicates that there were more and finer TiC precipitates coherent or semi-coherent with the ferrite matrix in the high manganese content steel than in low manganese content steel. The marked improvement in strength is also associated with low sulfur content. TiC particles smaller than 20 nm in 8Ti-8Mn steel help enhance strength to higher than 302 MPa compared with 8Mn steel.

Engineering properties for high kitchen waste content municipal solid waste

Directory of Open Access Journals (Sweden)

Wu Gao

2015-12-01

Full Text Available Engineering properties of municipal solid waste (MSW depend largely on the waste's initial composition and degree of degradation. MSWs in developing countries usually have a high kitchen waste content (called HKWC MSW. After comparing and analyzing the laboratory and field test results of physical composition, hydraulic properties, gas generation and gas permeability, and mechanical properties for HKWC MSW and low kitchen waste content MSW (called LKWC MSW, the following findings were obtained: (1 HKWC MSW has a higher initial water content (IWC than LKWC MSW, but the field capacities of decomposed HKWC and LKWC MSWs are similar; (2 the hydraulic conductivity and gas permeability for HKWC MSW are both an order of magnitude smaller than those for LKWC MSW; (3 compared with LKWC MSW, HKWC MSW has a higher landfill gas (LFG generation rate but a shorter duration and a lower potential capacity; (4 the primary compression feature for decomposed HKWC MSW is similar to that of decomposed LKWC MSW, but the compression induced by degradation of HKWC MSW is greater than that of LKWC MSW; and (5 the shear strength of HKWC MSW changes significantly with time and strain. Based on the differences of engineering properties between these two kinds of MSWs, the geo-environmental issues in HKWC MSW landfills were analyzed, including high leachate production, high leachate mounds, low LFG collection efficiency, large settlement and slope stability problem, and corresponding advice for the management and design of HKWC MSW landfills was recommended.

The technology of uranium extraction from the brine with high chlorine-ion content

International Nuclear Information System (INIS)

Khakimov, N.; Nazarov, Kh.M.; Mirsaidov, I.U.; Negmatov, Sh.I.; Barotov, B.B.

2010-01-01

Present article is devoted to technology of uranium extraction from the brine with high chlorine-ion content. The research results on uranium extraction from the brine of Sasik-Kul Lake by means of sorption method were considered. The chemical composition of salt was determined. The process of uranium sorption was described and analyzed. The technology of uranium extraction from the brine with high chlorine-ion content was proposed.

Corrosion Performance of Inconel 625 in High Sulphate Content

Science.gov (United States)

Ismail, Azzura

2016-05-01

Inconel 625 (UNS N06625) is a type of nickel-chromium-molybdenum alloy with excellent corrosion resistance in a wide range of corrosive media, being especially resistant to pitting and crevice corrosion. However, in aggressive environment, Inconel 625 will suffer corrosion attack like other metals. This research compared the corrosion performance of Inconel 625 when exposed to higher sulphate content compared to real seawater. The results reveal that Inconel 625 is excellent in resist the corrosion attack in seawater. However, at increasing temperature, the corrosion resistance of this metal decrease. The performance is same in seawater with high sulphate content at increasing temperature. It can be concluded that sulphate promote perforation on Inconel 625 and become aggressive agents that accelerate the corrosion attack.

Enhancing protein to extremely high content in photosynthetic bacteria during biogas slurry treatment.

Science.gov (United States)

Yang, Anqi; Zhang, Guangming; Meng, Fan; Lu, Pei; Wang, Xintian; Peng, Meng

2017-12-01

This work proposed a novel approach to achieve an extremely high protein content in photosynthetic bacteria (PSB) using biogas slurry as a culturing medium. The results showed the protein content of PSB could be enhanced strongly to 90% in the biogas slurry, which was much higher than reported microbial protein contents. The slurry was partially purified at the same time. Dark-aerobic was more beneficial than light-anaerobic condition for protein accumulation. High salinity and high ammonia of the biogas slurry were the main causes for protein enhancement. In addition, the biogas slurry provided a good buffer system for PSB to grow. The biosynthesis mechanism of protein in PSB was explored according to theoretical analysis. During biogas slurry treatment, the activities of glutamate synthase and glutamine synthetase were increased by 26.55%, 46.95% respectively. Copyright © 2017 Elsevier Ltd. All rights reserved.

Automated analysis of high-content microscopy data with deep learning.

Science.gov (United States)

Kraus, Oren Z; Grys, Ben T; Ba, Jimmy; Chong, Yolanda; Frey, Brendan J; Boone, Charles; Andrews, Brenda J

2017-04-18

Existing computational pipelines for quantitative analysis of high-content microscopy data rely on traditional machine learning approaches that fail to accurately classify more than a single dataset without substantial tuning and training, requiring extensive analysis. Here, we demonstrate that the application of deep learning to biological image data can overcome the pitfalls associated with conventional machine learning classifiers. Using a deep convolutional neural network (DeepLoc) to analyze yeast cell images, we show improved performance over traditional approaches in the automated classification of protein subcellular localization. We also demonstrate the ability of DeepLoc to classify highly divergent image sets, including images of pheromone-arrested cells with abnormal cellular morphology, as well as images generated in different genetic backgrounds and in different laboratories. We offer an open-source implementation that enables updating DeepLoc on new microscopy datasets. This study highlights deep learning as an important tool for the expedited analysis of high-content microscopy data. © 2017 The Authors. Published under the terms of the CC BY 4.0 license.

The influence of compound admixtures on the properties of high-content slag cement

Energy Technology Data Exchange (ETDEWEB)

Dongxu, L.; Xuequan, W.; Jinlin, S.; Yujiang, W.

2000-01-01

Based on the activation theory of alkali and sulfate, the influence of compound admixtures on the properties of high-content slag cement was studied by testing the strength, pore structure, hydrates, and microstructure, Test results show that compound admixtures can obviously improve the properties of high-content slag cement. The emphasis of the present research is two-fold: substituting gypsum with anhydrite and calcining gypsum. These both can improve early and later performance.

Improvement of Heavy Oil Recovery in the VAPEX Process using Montmorillonite Nanoclays Amélioration de la récupération d’huile lourde par utilisation de nanoargiles de Montmorillonite dans le procédé VAPEX

Directory of Open Access Journals (Sweden)

Pourabdollah K.

2011-10-01

Full Text Available In this paper, the nanoclay particles were introduced as mobile adsorbents in oil reservoirs to adsorb the asphaltenes, reduce the viscosity and enhance the dispersion. The objective of this paper is experimental investigation of enhanced heavy oil recovery using in situ nanoparticles for the first time. Moreover, two thermal analysis methods (thermogravimetry and differential thermal analysis were used to analyze the asphaltene content of residue hydrocarbons in the swept chambers in nano-assisted and conventional VAPEX processes. Experiments were carried out using Iranian heavy oil and propane: the setup consisted of two sand-packed cells; one packed only with glass beads as the oil matrix and the other with glass beads and modified montmorillonite as the nanoclay, while they had similar porosity and permeability. The content of deposited asphaltene in swept matrixes, the propagation pattern of vapor chambers in heavy oil matrixes, and the rates of solvent consumption and oil production were determined. The results elucidated that montmorillonite changed the matrix heterogeneity and led to forming enhanced breakthroughs, to increasing the interfacial surface of vapor/bitumen and to accelerating the oil production. It was found that not only was the rate of vapor injection diminished, but the heavy oil recovery was also markedly enhanced by 30(±4%. Dans cet article, on decrit l’utilisation de particules de nanoargile en tant qu’adsorbant mobile dans des reservoirs d’huile afin d’adsorber les asphaltenes, reduire la viscosite de l’huile et renforcer la dispersion. L’objectif de cet article consiste en la description d’une etude experimentale de recuperation amelioree d’huile lourde par l’utilisation de nanoparticules in situ. Ce qui constitue une premiere. En outre, deux methodes d’analyse thermique (thermogravimetrie et analyse thermique differentielle ont ete utilisees pour analyser la teneur en asphaltene des residus d�

SCC with high volume of fly ash content

Directory of Open Access Journals (Sweden)

Bakhrakh Anton

2017-01-01

Full Text Available Self-compacting concrete is a very perspective building material. It provides great benefits during the construction of heavily reinforced buildings. SCC has outstanding properties such as high flowability, dense structure and high strength due to specific quality of aggregates, fillers, their proportion in mix, use of polycarboxylate-based superplasticizers. Main disadvantages of SCC are high price and the difficulty of obtaining a proper mix. Use of fillers, such as fly ash type F, is a way to make SCC cheaper by replacing part of cement. Fly ash also provides some technological and operating advantages. In this paper the influence of high volume (60% from cement fly ash type F on the properties of concrete mixture and hardened concrete is investigated. The result of the work shows the possibility of reduction the cost of SCC using ordinary fillers and high amount of fly ash. The investigated SCC has low speed of hardening (7-day compressive strength at the range of 41.8 MPa and high volume of entrained air content (3.5%.

Influence of Ta Content in High Purity Niobium on Cavity Performance Preliminary Results*

CERN Document Server

Kneisel, P

2004-01-01

In a previous paper* a program designed to study the influence of the residual tantalum content on the superconducting properties of pure niobium metal for RF cavities was outlined. The main rationale for this program was based on a potential cost reduction for high purity niobium, if a less strict limit on the chemical specification for Ta content, which is not significantly affecting the RRR–value, could be tolerated for high performance cavities. Four ingots with different Ta contents have been melted and transformed into sheets. In each manufacturing step the quality of the material has been monitored by employing chemical analysis, neutron activation analysis, thermal conductivity measurements and evaluation of the mechanical properties. The niobium sheets have been scanned for defects by an eddy current device. From three of the four ingots—Ta contents 100, 600 and 1,200 wppm—two single cell cavities each of the CEBAF variety have been fabricated and a series of tests on each ...

Determination of the streaming potential and the corresponding total charge in aqueous asphalthene containing suspensions; Bestimmung der Stroemungspotentiale und der korrespondierenden Gesamtladungen in waessrigen, asphaltenhaltigen Suspensionen

Energy Technology Data Exchange (ETDEWEB)

Edler, S. [Inst. fuer Erdoel- und Erdgasforschung, Clausthal-Zellerfeld (Germany); Rosenplaenter, A. [Inst. fuer Erdoel- und Erdgasforschung, Clausthal-Zellerfeld (Germany); Rahimian, I. [Inst. fuer Erdoel- und Erdgasforschung, Clausthal-Zellerfeld (Germany)

1996-02-01

The choice of demulgators for separating crude oil emulsions is still done empirically. The knowledge of the charge of crude oil compounds is essential for the amount of needed demulsifiers. By using the Particle Charge Detector of the Muetek Company the surface charges of these compounds could be determined. The suspension will be titrated with demulsifier. Surface active compounds ar enriched within the colloids of crude oil, i.e. the resins and the asphaltenes. The asphaltenes could be divided into the easy, medium and difficult soluble asphaltenes. The streaming potential of the colloids and their corresponding total charge could be determined successfully. With increasing quantity of asphaltenes the charge consumption increase almost linearly. The heavy soluble asphaltenes are needing the highest share of demulsifiers followed by the middle and the light soluble asphaltenes. The resins only show very small charge consumption. (orig.) [Deutsch] Die Auswahl von Spaltern zur Trennung von Rohoelemulsionen erfolgt zumeist empirisch. Bei Kenntnis der Ladung der rohoeleigenen Emulgatoren ist eine gezieltere Auswahl der Splater moeglich. Mit Hilfe eines Partikelladungsdetektors sollten die Oberflaechenladungen der rohoeleigenen Emulgatoren bestimmt werden. Dazu wurden Suspensionen der Rohoelkolloide mit Tensid titriert. Grenzflaechenaktive Stoffe sind in den Rohoelkolloiden, also den Erdoelharzen und den Asphaltenen, angereichert. Die Asphaltene lassen sich in leicht-, mittel- und schwerloesliche Komponenten einteilen. Es konnte das Stroemungspotential der Rohoelkolloide und die korrespondierende Gesamtladung erfolgreich bestimmt werden. Mit konstant steigendem Gehalt an Kolloiden steigt auch der Ladungsverbrauch annaehernd linear. Bei den Asphaltenfraktionen verbrauchen die schwerloeslichen Asphaltene mit Abstand den groessten Anteil der Ladung, gefolgt von den mittel- und den leichtloeslichen. Die Erdoelharze zeigen einen sehr geringen Ladungsverbrauch. (orig.)

Evaluation of ultra-high-performance-fiber reinforced concrete binder content using the response surface method

International Nuclear Information System (INIS)

Aldahdooh, M.A.A.; Muhamad Bunnori, N.; Megat Johari, M.A.

2013-01-01

Highlights: • We develop a practical method for adjusting the binder content of UHP-FRC. • We adjust the binder content of UHP-FRC mixtures using RSM. • Increasing the cement content does not contribute to enhance strength. • Increasing the content of cement will increase the flow of UHP-FRC mixtures. - Abstract: One of the major disadvantages in ultra-high-performance-fiber reinforced concrete (UHP-FRC) is its high ordinary Portland cement (OPC) content, which directly translates into an increase in OPC production. More OPC production results in increased emission of greenhouse gases, as well increased electrical energy consumption and concrete price. This study is aimed at adjusting the binder content (OPC and silica fume (SF) contents) of UHP-FRC using the response surface method. The present investigation shows that, for a given water/binder and superplasticizer/OPC, the compressive strength is independent of the binder content, whereas the flow depends on the binder content. Increasing the binder content does not enhance the strength compared with the required design strength because the capillary porosity increases with increasing OPC content; however, the workability increases. The final result is the production of a UHP-FRC with an OPC content of 720.49 kg/m 3 , an SF content of 214.25 kg/m 3 , a compressive strength of 181.41 MPa, a direct tensile strength of 12.49 MPa, a bending tensile strength of 30.31 MPa, and a flow of 167 mm

GENERALIZATION, FORMULATION AND HEAT CONTENTS OF SIMULATED MSW WITH HIGH MOISTURE CONTENT

Directory of Open Access Journals (Sweden)

A. JOHARI

2012-12-01

Full Text Available This paper presents a generalization technique for the formulation of simulated municipal solid waste. This technique is used for the elimination of the inconsistency in the municipal solid waste (MSW characteristics due to its heterogeneous nature. The compositions of simulated municipal solid waste were formulated from four major municipal waste streams components in Malaysia namely paper, plastic, food and yard waste. The technique produced four simplified waste generalization categories with composition of paper (19%, plastic (25%, food (27% and green waste (29% respectively. Comparative study was conducted for proximate analysis for the determination of volatile matter, fixed carbon and ash content. Ultimate analysis was performed for carbon and hydrogen content. The heat content for simulated and actual municipal solid waste showed good agreement. The moisture content of the simulated municipal solid waste and actual municipal solid waste were established at 52.34% and 61.71% respectively. Overall results were considered to be representative of the actual compositions of municipal solid waste in Malaysia.

Effect of the structure of commercial poly(ethylene oxide-b-propylene oxide) demulsifier bases on the demulsification of water-in-crude oil emulsions: elucidation of the demulsification mechanism

Energy Technology Data Exchange (ETDEWEB)

Ramalho, Joao Batista V.S. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas; Lechuga, Fernanda C.; Lucas, Elizabete F., E-mail: elucas@ima.ufrj.b [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Inst. de Macromoleculas Profa. Eloisa Mano

2010-07-01

Water-in-crude oil emulsions are formed during petroleum production and asphaltenes play an important role in their stabilization. Demulsifiers are added to destabilize such emulsions,however the demulsification mechanism is not completely known. In this paper, the performances of commercial poly(ethylene oxide-b-propylene oxide) demulsifiers were studied using synthetic water-in-oil emulsions and model-systems (asphaltenes in organic solvent). No change in the asphaltene aggregate size induced by the demulsifier was observed. The demulsification performance decreased as the asphaltene aggregate size increased, so it can be suggested that the demulsification mechanism is correlated to the voids between the aggregates adsorbed on the water droplets surface. (author)

Effect of the structure of commercial poly(ethylene oxide-b-propylene oxide) demulsifier bases on the demulsification of water-in-crude oil emulsions: elucidation of the demulsification mechanism

International Nuclear Information System (INIS)

Ramalho, Joao Batista V.S.; Lechuga, Fernanda C.; Lucas, Elizabete F.

2010-01-01

Water-in-crude oil emulsions are formed during petroleum production and asphaltenes play an important role in their stabilization. Demulsifiers are added to destabilize such emulsions,however the demulsification mechanism is not completely known. In this paper, the performances of commercial poly(ethylene oxide-b-propylene oxide) demulsifiers were studied using synthetic water-in-oil emulsions and model-systems (asphaltenes in organic solvent). No change in the asphaltene aggregate size induced by the demulsifier was observed. The demulsification performance decreased as the asphaltene aggregate size increased, so it can be suggested that the demulsification mechanism is correlated to the voids between the aggregates adsorbed on the water droplets surface. (author)

Hot forging of roll-cast high aluminum content magnesium alloys

Science.gov (United States)

Kishi, Tomohiro; Watari, Hisaki; Suzuki, Mayumi; Haga, Toshio

2017-10-01

This paper reports on hot forging of high aluminum content magnesium alloy sheets manufactured using horizontal twin-roll casting. AZ111 and AZ131 were applied for twin-roll casting, and a hot-forging test was performed to manufacture high-strength magnesium alloy components economically. For twin-roll casting, the casting conditions of a thick sheet for hot forging were investigated. It was found that twin-roll casting of a 10mm-thick magnesium alloy sheet was possible at a roll speed of 2.5m/min. The grain size of the cast strip was 50 to 70µm. In the hot-forging test, blank material was obtained from as-cast strip. A servo press machine with a servo die cushion was used to investigate appropriate forging conditions (e.g., temperature, forging load, and back pressure) for twin-roll casts (TRCs) AZ111 and AZ131. It was determined that high aluminum content magnesium alloy sheets manufactured using twin-roll casting could be forged with a forging load of 150t and a back pressure of 3t at 420 to 430°C. Applying back pressure during hot forging effectively forged a pin-shaped product.

Vacuum distillation residue upgrading by an indigenous Bacillus cereus.

Science.gov (United States)

Tabatabaee, Mitra Sadat; Mazaheri Assadi, Mahnaz

2013-07-16

Biological processing of heavy fractions of crude oils offers less severe process conditions and higher selectivity for refining. Biochemical Processes are expected to be low demand energy processes and certainly ecofriendly. A strain of biosurfactant producing bacterium was isolated from an oil contaminated soil at Tehran refinery distillation unit. Based on selected phenotypic and genotypic characteristic including morphology, biochemical proprety, and 16 SrRNA sequencing identified as a novel strain of Bacillus cereus (JQ178332). This bacterium endures a wide range of pH, salinity and temperature. This specific strain utilizes both paraffin and anthracene as samples of aliphatic and polycyclic aromatic hydrocarbons. The ability of this bacterium to acquire all its energy and chemical requirements from Vacuum Distillation Residue (VR), as a net sample of problematic hydrocarbons in refineries, was studied. SARA test ASTM D4124-01 revealed 65.5% decrease in asphaltenic, 22.1% in aliphatics and 30.3% in Aromatics content of the VR in MSM medium. Further results with 0.9% saline showed 55% decrease in asphaltene content and 2.1% Aromatics respectively. Remarkable abilities of this microorganism propose its application in an ecofriendly technology to upgrade heavy crude oils.

The effect of High Pressure and High Temperature processing on carotenoids and chlorophylls content in some vegetables.

Science.gov (United States)

Sánchez, Celia; Baranda, Ana Beatriz; Martínez de Marañón, Iñigo

2014-11-15

The effect of High Pressure (HP) and High Pressure High Temperature (HPHT) processing on carotenoid and chlorophyll content of six vegetables was evaluated. In general, carotenoid content was not significantly influenced by HP or HPHT treatments (625 MPa; 5 min; 20, 70 and 117 °C). Regarding chlorophylls, HP treatment caused no degradation or slight increases, while HPHT processes degraded both chlorophylls. Chlorophyll b was more stable than chlorophyll a at 70 °C, but both of them were highly degraded at 117 °C. HPHT treatment at 117 °C provided products with a good retention of carotenoids and colour in the case of red vegetables. Even though the carotenoids also remained in the green vegetables, their chlorophylls and therefore their colour were so affected that milder temperatures need to be applied. As an industrial scale equipment was used, results will be useful for future industrial implementation of this technology. Copyright © 2014 Elsevier Ltd. All rights reserved.

Investigation of the photoluminescence properties of composite optical resins containing high lanthanide content

International Nuclear Information System (INIS)

Wang Dongmei; Wang Fuxiang; Peng Weixian

2012-01-01

Novel composite optical resins with high lanthanide content have been synthesized through a free radical copolymerization of methacrylic acid (MA), styrene (St) and Eu(DBM) 3 ·H 2 O nanocrystals. We characterized the structure, the thermal properties, dimensions and photoluminescence properties of Eu(DBM) 3 ·H 2 O nanocrystals. Our results indicated that the diameters of the Eu(DBM) 3 ·H 2 O nanocrystals were within the range of 30 to 300 nm. These materials exhibited characteristic europium ion luminescence. The europium-bearing nanocrystals and were then incorporated into the copolymer systems of MA/St and luminescence functional optical resins with high lanthanide content (50 wt%) were obtained. The combination of these particles and optical resins is facile because the diameter of Eu(DBM) 3 ·H 2 O is decreased. These copolymer-based optical resins not only possess good transparency and mechanical performance, but also exhibit an intense narrow band emission of lanthanide complexes and longer fluorescence lifetimes under UV excitation at room temperature. - Highlights: ► Novel composite optical resins with high lanthanide content have been synthesized. ► The Eu(DBM) 3 ·H 2 O nanocrystals were within the range of 30 to 300 nm. ► Fluorescent resins with high lanthanide content (50 wt%) were obtained. ► Resins exhibit intense emission of lanthanide and longer fluorescence lifetimes. ► Variety properties of Eu(DBM) 3 ·H 2 O nanocrystals were characterized.

Automation in high-content flow cytometry screening.

Science.gov (United States)

Naumann, U; Wand, M P

2009-09-01

High-content flow cytometric screening (FC-HCS) is a 21st Century technology that combines robotic fluid handling, flow cytometric instrumentation, and bioinformatics software, so that relatively large numbers of flow cytometric samples can be processed and analysed in a short period of time. We revisit a recent application of FC-HCS to the problem of cellular signature definition for acute graft-versus-host-disease. Our focus is on automation of the data processing steps using recent advances in statistical methodology. We demonstrate that effective results, on par with those obtained via manual processing, can be achieved using our automatic techniques. Such automation of FC-HCS has the potential to drastically improve diagnosis and biomarker identification.

Chemical aspects of shale and shale oils

Energy Technology Data Exchange (ETDEWEB)

Hackford, J E

1922-01-01

To prove that the kerogen in oil shale is a form of bitumen, several experiments were made with oil shale and a heavy asphaltic oil mixed with fuller's earth. When distilled, both the oil shale and asphalt-impregnated fuller's earth yielded paraffin oil, wax, and hydrogen sulfide (if sulfur was present). Both yielded ammonia if nitrogen was present. The organic material in each was partly isolated by extraction with pyridine and appeared to be the same. Oil shale is a marl that was saturated with oil or through which oil has passed or filtered. The insolubilities of its organic compounds are due to a slightly elevated temperature for a prolonged period and to the retaining effect exerted by the finely divided marl. The marl exerted a selective action on the oil and absorbed the asphaltum, sulfur, and nitrogen compounds from the oil. The class of oil evolved from a shale depended on the nature of the original compounds absorbed. Asphaltenes obtained from crude oil by precipitation with ethyl ether produced distillation products of water, hydrogen sulfide, ammonia, oil, wax, and a carbonaceous residue. Water was formed by decomposition of oxyasphaltenes and hydrogen sulfide by decomposition of thioasphaltenes. Ammonia was evolved during decomposition if lime was present, but if there was not sufficient free lime present, pyridine and pyrrole derivatives were redistilled as such. The oil and wax that resulted from the dry distillation were true decomposition products and equaled about 60 weight-percent of the asphaltenes. The oil and wax content of the mixture varied between 8 and 10 percent. The carbonaceous residue, which represented approximately 40 percent of the original asphaltene, was a decomposition product of the asphaltenes. Geologic comparisons of oil-shale deposits and oil-well fields were also made.

Nonisothermal Thermogravimetric Analysis of Thai Lignite with High CaO Content

Science.gov (United States)

Pintana, Pakamon

2013-01-01

Thermal behaviors and combustion kinetics of Thai lignite with different SO3-free CaO contents were investigated. Nonisothermal thermogravimetric method was carried out under oxygen environment at heating rates of 10, 30, and 50°C min−1 from ambient up to 1300°C. Flynn-Wall-Ozawa (FWO) and Kissinger-Akahira-Sunose (KAS) methods were adopted to estimate the apparent activation energy (E) for the thermal decomposition of these coals. Different thermal degradation behaviors were observed in lignites with low (14%) and high (42%) CaO content. Activation energy of the lignite combustion was found to vary with the conversion fraction. In comparison with the KAS method, higher E values were obtained by the FWO method for all conversions considered. High CaO lignite was observed to have higher activation energy than the low CaO coal. PMID:24250259

Optimizing cationic and neutral lipids for efficient gene delivery at high serum content.

Science.gov (United States)

Chan, Chia-Ling; Ewert, Kai K; Majzoub, Ramsey N; Hwu, Yeu-Kuang; Liang, Keng S; Leal, Cecília; Safinya, Cyrus R

2014-01-01

Cationic liposome (CL)-DNA complexes are promising gene delivery vectors with potential application in gene therapy. A key challenge in creating CL-DNA complexes for application is that their transfection efficiency (TE) is adversely affected by serum. In particular, little is known about the effects of a high serum content on TE, even though this may provide design guidelines for application in vivo. We prepared CL-DNA complexes in which we varied the neutral lipid [1,2-dioleoyl-sn-glycerophosphatidylcholine, glycerol-monooleate (GMO), cholesterol], the headgroup charge and chemical structure of the cationic lipid, and the ratio of neutral to cationic lipid; we then measured the TE of these complexes as a function of serum content and assessed their cytotoxicity. We tested selected formulations in two human cancer cell lines (M21/melanoma and PC-3/prostate cancer). In the absence of serum, all CL-DNA complexes of custom-synthesized multivalent lipids show high TE. Certain combinations of multivalent lipids and neutral lipids, such as MVL5(5+)/GMO-DNA complexes or complexes based on the dendritic-headgroup lipid TMVLG3(8+) exhibited high TE both in the absence and presence of serum. Although their TE still dropped to a small extent in the presence of serum, it reached or surpassed that of benchmark commercial transfection reagents, particularly at a high serum content. Two-component vectors (one multivalent cationic lipid and one neutral lipid) can rival or surpass benchmark reagents at low and high serum contents (up to 50%, v/v). We propose guidelines for optimizing the serum resistance of CL-DNA complexes based on a given cationic lipid. Copyright © 2014 John Wiley & Sons, Ltd.

Effect of the structure of commercial poly(ethylene oxide-b-propylene oxide demulsifier bases on the demulsification of water-in-crude oil emulsions: elucidation of the demulsification mechanism

Directory of Open Access Journals (Sweden)

João Batista V. S. Ramalho

2010-01-01

Full Text Available Water-in-crude oil emulsions are formed during petroleum production and asphaltenes play an important role in their stabilization. Demulsifiers are added to destabilize such emulsions,however the demulsification mechanism is not completely known. In this paper, the performances of commercial poly(ethylene oxide-b-propylene oxide demulsifiers were studied using synthetic water-in-oil emulsions and model-systems (asphaltenes in organic solvent. No change in the asphaltene aggregate size induced by the demulsifier was observed. The demulsification performance decreased as the asphaltene aggregate size increased, so it can be suggested that the demulsification mechanism is correlated to the voids between the aggregates adsorbed on the water droplets surface.

Leaching of copper concentrates with high arsenic content in chlorine-chloride media

International Nuclear Information System (INIS)

Herreros, O.; Fuentes, G.; Quiroz, R.; Vinals, J.

2003-01-01

This work reports the results of copper concentrates leaching which have high arsenic concepts (up to 2.5%). The treatments were carried out using chlorine that forms from sodium hypochlorite and sulphuric acid. The aim of this work is to obtain a solution having high copper content 4 to 6 g/l and 5 to 7 g/l free acid in order to submit it directly to a solvent extraction stage. In addition, this solution should have minimum content of arsenic and chloride ions. To carry out this investigation, an acrylic reactor was constructed where the leaching tests were made at constant temperature in a thermostatic bath under atmospheric pressure. The concentrate samples were obtained from mineral processing plants from Antofagasta, Chile. Typical variables were studied, such as leaching agent concentration, leaching time, pulp density and temperature among others. Some of the residues were analyzed by XRD and EPS. On the other hand, the solutions were analyzed by Atomic Absorption Spectroscopy. The results indicate solutions having the contents stated above can be obtained. (Author) 19 refs

Selection of catalysts and reactors for hydroprocessing

Energy Technology Data Exchange (ETDEWEB)

Furimsky, E. [Imaf Group, Ottawa, ON (Canada)

1998-07-13

The performance of hydroprocessing units can be influenced by the selection of the catalysts and the type of reactor to suit a particular feed. The catalysts and reactors selected for light feeds differ markedly from those selected for heavy feeds. Fixed-bed reactors have been traditionally used for light feeds. High asphaltene and high metal content feeds are successfully processed using moving-bed and/or ebullated bed reactors. Multi-reactor systems consisting of moving-bed and/or ebullated bed reactors in series with fixed-bed reactors can be used to process difficult feeds. For heavy feeds, the physical properties (e.g. porosity), shape and size of the catalyst particles become crucial parameters. Pretreatment of catalysts by presulfiding improves the performance of the units.

Highly ordered macroporous woody biochar with ultra-high carbon content as supercapacitor electrodes

International Nuclear Information System (INIS)

Jiang, Junhua; Zhang, Lei; Wang, Xinying; Holm, Nancy; Rajagopalan, Kishore; Chen, Fanglin; Ma, Shuguo

2013-01-01

Woody biochar monolith with ultra-high carbon content and highly ordered macropores has been prepared via one-pot pyrolysis and carbonization of red cedar wood at 750 °C without the need of post-treatment. Energy-dispersive spectroscope (EDX) and scanning electron microscope (SEM) studies show that the original biochar has a carbon content of 98 wt% with oxygen as the only detectable impurity and highly ordered macroporous texture characterized by alternating regular macroporous regions and narrow porous regions. Moreover, the hierarchically porous biochar monolith has a high BET specific surface area of approximately 400 m 2 g −1 . We have studied the monolith material as supercapacitor electrodes under acidic environment using electrochemical and surface characterization techniques. Electrochemical measurements show that the original biochar electrodes have a potential window of about 1.3 V and exhibit typical rectangular-shape voltammetric responses and fast charging–discharging behavior with a gravimetric capacitance of about 14 F g −1 . Simple activation of biochar in diluted nitric acid at room temperature leads to 7 times increase in the capacitance (115 F g −1 ). Because the HNO 3 -activation slightly decreases rather than increases the BET surface area of the biochar, an increase in the coverage of surface oxygen groups is the most likely origin of the substantial capacitance improvement. This is supported by EDX, X-ray photoelectron spectroscopy (XPS), and Raman measurements. Preliminary life-time studies show that biochar supercapacitors using the original and HNO 3 -activated electrodes are stable over 5000 cycles without performance decays. These facts indicate that the use of woody biochar is promising for its low cost and it can be a good performance electrode with low environmental impacts for supercapacitor applications

Modeled effects on permittivity measurements of water content in high surface area porous media

International Nuclear Information System (INIS)

Jones, S.B.; Or, Dani

2003-01-01

Time domain reflectometry (TDR) has become an important measurement technique for determination of porous media water content and electrical conductivity due to its accuracy, fast response and automation capability. Water content is inferred from the measured bulk dielectric constant based on travel time analysis along simple transmission lines. TDR measurements in low surface area porous media accurately describe water content using an empirical relationship. Measurement discrepancies arise from dominating influences such as bound water due to high surface area, extreme aspect ratio particles or atypical water phase configuration. Our objectives were to highlight primary factors affecting dielectric permittivity measurements for water content determination in porous mixtures, and demonstrate the influence of these factors on mixture permittivity as predicted by a three-phase dielectric mixture model. Modeled results considering water binding, higher porosity, constituent geometry or phase configuration suggest any of these effects individually are capable of causing permittivity reduction, though all likely contribute in high surface area porous media

Preventing performance drops of coal mills due to high moisture content

DEFF Research Database (Denmark)

Odgaard, Peter Fogh; Stoustrup, Jakob; Mataji, B.

2007-01-01

Coal mills pulverize and dry the coal dust before it is blown into the furnace in coal-fired power plants. The coal mills can only deliver the requested coal flow if certain conditions are fulfilled. These are normally considered as constraints on individual variables. However, combinations of more...... than one variable might cause problems even though these individually variables are in an acceptable region. This paper deals with such a problem. The combination of a high load of the power plant, a large load change and high moisture content in the coal, can force the coal mill into a state where...... coal is accumulated instead of being blown into the furnace. This paper suggests a simple method for preventing the accumulation of the coal in the mill, by limiting the requested coal flow considering the coal moisture content and the temperature outside the mill.  ...

Highly luminescent, high-indium-content InGaN film with uniform composition and full misfit-strain relaxation

Science.gov (United States)

Fischer, A. M.; Wei, Y. O.; Ponce, F. A.; Moseley, M.; Gunning, B.; Doolittle, W. A.

2013-09-01

We have studied the properties of thick InxGa1-xN films, with indium content ranging from x ˜ 0.22 to 0.67, grown by metal-modulated epitaxy. While the low indium-content films exhibit high density of stacking faults and dislocations, a significant improvement in the crystalline quality and optical properties has been observed starting at x ˜ 0.6. Surprisingly, the InxGa1-xN film with x ˜ 0.67 exhibits high luminescence intensity, low defect density, and uniform full lattice-mismatch strain relaxation. The efficient strain relaxation is shown to be due to a critical thickness close to the monolayer range. These films were grown at low temperatures (˜400 °C) to facilitate indium incorporation and with precursor modulation to enhance surface morphology and metal adlayer diffusion. These findings should contribute to the development of growth techniques for nitride semiconductors under high lattice misfit conditions.

Estimation of quality and yields of products from the process of future national oils indelayed coking units; Estimativa da qualidade e dos rendimentos de produtos de coqueamento a partir do processamento de petroleos nacionais

Energy Technology Data Exchange (ETDEWEB)

Filipakis, Sofia D.; Silva, Maria do Socorro A.J. da; Guimaraes, Regina C.L. [PETROBRAS, Rio de Janeiro, RJ (Brazil)

2008-07-01

As the importance of the delayed coking process increases in the Brazilian refinery scenario, it is necessary to perform a more detailed evaluation of vacuum residues potential on this kind of process. This work compares the performance of future produced and exported oils residues with those which are references nowadays as delayed coking feeding. This information is essential for the prediction of the future quality and yield of the products generated by this process, and for the determination of the oils value for exportation. For this purpose, a process simulator was used considering the operational conditions of a real delayed coking unit. The carbon residue and asphaltenes ratio from the residues were also evaluated. This simulation demonstrated that most of the future oils will produce a high quality coke from the point of view of crystallinity and metals content, and it will present high contents of both volatile matter and sulphur. The exported oils residues are likely to show good crystallinity. (author)

Microspheres with an ultra high holmium content for brachytherapy of malignancies

International Nuclear Information System (INIS)

Lira, Raphael A.; Myamoto, Douglas M.; Souza, Jaime R.; Nascimento, Nanci; Azevedo, Mariangela de Burgos M. de; Osso Junior, Joao A.; Martinelli, Jose R.

2011-01-01

The overall objective of this work is to develop biodegradable microspheres intended for internal radiation therapy which provides an improved treatment for hepatic carcinomas. The most studied brachytherapy system employing microspheres made of holmium-biopolymer system is composed by poly(L-lactic acid) (PLLA) and holmium acetylacetonate (HoAcAc). The importance of the holmium high content in the microspheres can be interpreted as follow from a therapeutic standpoint, to achieve an effective use of microspheres loaded with HoAcAc, a high content of holmium is required to yield enough radioactivity with a relatively low amount of microspheres.The usual amounts of holmium that are incorporated in the microspheres composed by poly(L-lactic acid) and HoAcAc are 17.0 ± 0.5% (w/w) of holmium, which corresponds to a loading of about 50% of HoAcAc. Different approaches have been investigated to increase that value. One updated approach towards this direction is the production of microspheres with ultrahigh holmium as matrix using HoAcAc crystals as the sole starting material without the use of biopolymer. Likewise, in the search of microspheres with increased holmium content , it has been demonstrated that by changing the HoAcAc crystal structure by its recrystallization from crystal phase to the amorphous there is lost of acetylacetonate and water molecules causing the increasing of the holmium content. Microspheres were prepared by solvent evaporation, using holmium acetylacetonate (HoAcAc) crystals as the sole ingredient. Microspheres were characterized by using light and scanning electron microscopy, infrared and Raman spectroscopy, differential scanning calorimetry, X-rays diffraction, and confocal laser scanning microscopy. (author)

Microspheres with an ultra high holmium content for brachytherapy of malignancies

Energy Technology Data Exchange (ETDEWEB)

Lira, Raphael A.; Myamoto, Douglas M.; Souza, Jaime R.; Nascimento, Nanci; Azevedo, Mariangela de Burgos M. de [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Centro de Biotecnologia; Osso Junior, Joao A. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Centro de Radiofarmacia; Martinelli, Jose R. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Centro de Ciencias e Tecnologia de Materiais

2011-07-01

The overall objective of this work is to develop biodegradable microspheres intended for internal radiation therapy which provides an improved treatment for hepatic carcinomas. The most studied brachytherapy system employing microspheres made of holmium-biopolymer system is composed by poly(L-lactic acid) (PLLA) and holmium acetylacetonate (HoAcAc). The importance of the holmium high content in the microspheres can be interpreted as follow from a therapeutic standpoint, to achieve an effective use of microspheres loaded with HoAcAc, a high content of holmium is required to yield enough radioactivity with a relatively low amount of microspheres.The usual amounts of holmium that are incorporated in the microspheres composed by poly(L-lactic acid) and HoAcAc are 17.0 {+-} 0.5% (w/w) of holmium, which corresponds to a loading of about 50% of HoAcAc. Different approaches have been investigated to increase that value. One updated approach towards this direction is the production of microspheres with ultrahigh holmium as matrix using HoAcAc crystals as the sole starting material without the use of biopolymer. Likewise, in the search of microspheres with increased holmium content , it has been demonstrated that by changing the HoAcAc crystal structure by its recrystallization from crystal phase to the amorphous there is lost of acetylacetonate and water molecules causing the increasing of the holmium content. Microspheres were prepared by solvent evaporation, using holmium acetylacetonate (HoAcAc) crystals as the sole ingredient. Microspheres were characterized by using light and scanning electron microscopy, infrared and Raman spectroscopy, differential scanning calorimetry, X-rays diffraction, and confocal laser scanning microscopy. (author)

Flow of microemulsion through soil columns contaminated with asphaltic residue; Fluxo de microemulsoes atraves do solo contaminado com residuos asfalticos

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Marcia C.K.; Oliveira, Jose F. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE); Oliveira, Roberto C.G.; Gonzalez, Gazpar [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas

2004-07-01

Nowadays, soil contamination with nonaqueous phase liquids (NAPLs) such as petroleum hydrocarbons is a major environmental problem. Significant efforts have been devoted to the development of processes to remediate sites contaminated with NAPLs. Unfortunately, most of the developed processes proved to be inefficient to remove the organic heavy fraction present in the NAPLs. Nevertheless, in our preliminary bench scale tests it was observed that, due to their high solubilization capacity and stability, microemulsions are able to remove organic heavy fractions like asphaltenes and resins, typically present in crude oils. The present work was dimensioned to evaluate, under up-flow condition, the performance of different microemulsions specially designed to remove asphaltenes fractions from soils using a column test set-up. The contaminant residual concentration was quantified by UV spectroscopy and the microemulsion efficiency determined using mass balance. The results showed that the microemulsions tested have a high capacity for removing asphaltenes fractions from contaminated soils. It was also observed that the predominant removal mechanism, solubilization or mobilization, depends essentially on the microemulsion's chemical formulation. Finally it was verified that microemulsion's formulations based on natural solvents compounds are also efficient for removing asphaltic residues. (author)

Chemical composition of Pechora Sea crude oil

Directory of Open Access Journals (Sweden)

Derkach S. R.

2017-03-01

Full Text Available The physicochemical properties of the Pechora Sea shelf oil and its chemical composition have been studied using the methods of refractometry, titrimetry, viscometry, rheometry and standard methods for the analysis of oil and petroleum products. The fractionation of oil is held at atmospheric pressure, some fractions boiling at the temperature below and above 211 °C have been received. Chemical structural-group composition of oil and its components has been investigated using a Fourier infrared (IR spectroscopy method. The density of oil has been obtained, it is equal to 24.2 API. The chemical composition analysis shows that water content in the investigated oil sample is about 0.03 % (by weight. The oil sample contains hydrocarbons (including alkanes, naphthenes, arenes and asphaltenes with resins; their content is equal to 89 and 10 % (by weight respectively. Alkane content is about 66 %, including alkanes of normal structure – about 37 %. The solidification temperature of oil sample is equal to –43 °C. This low temperature testifies obliquely low content of solid alkanes (paraffin. Bearing in mind the content of asphaltenes with resins we can refer the investigated oil sample to resinous oils. On the other hand spectral coefficient values (aromaticity quotient and aliphaticity quotient show that oil sample belongs to naphthenic oils. According to the data of Fourier IR spectroscopy contents of naphthenes and arenes are 5.9 and 17.8 % respectively. Thus, the obtained data of chemical structural-group composition of crude oil and its fractions indicate that this oil belongs to the heavy resinous naphthenic oils. The rheological parameters obtained at the shear deformation conditions characterize the crude oil as a visco-plastic medium.

The relationship between SARA fractions and crude oil stability

Directory of Open Access Journals (Sweden)

Siavash Ashoori

2017-03-01

Full Text Available Asphaltene precipitation and deposition are drastic issues in the petroleum industry. Monitoring the asphaltene stability in crude oil is still a serious problem and has been subject of many studies. To investigate crude oil stability by saturate, aromatic, resin and asphaltene (SARA analysis seven types of crudes with different components were used. The applied methods for SARA quantification are IP-143 and ASTM D893-69 and the colloidal instability index (CII is computed from the SARA values as well. In comparison between CII results, the values of oil compositions demonstrated that the stability of asphaltenes in crude oils is a phenomenon that is related to all these components and it cannot be associated only with one of them, individually.

Internal friction in iron-aluminium alloys having a high aluminium content

International Nuclear Information System (INIS)

Hillairet, J.; Delaplace, J.; Silvent, A.

1966-01-01

By using a torsion pendulum to measure the internal friction of iron-aluminium alloys containing between 25 and 50 atom per cent of aluminium, it has been possible to show the existence of three damping peaks due to interstitial carbon. Their evolution is followed as a function of the carbon content, of the thermal treatment and of the aluminium content. A model based on the preferential occupation of tetrahedral sites is proposed as an interpretation of the results. A study of the Zener peak in these substitution alloys shows also that a part of the short distance disorder existing at high temperatures can be preserved by quenching. (author) [fr

Analysis of the relationship between the coal properties and their liquefaction characteristics by using the coal data base; Tanshu data base ni yoru tanshitsu to ekika tokusei no kaiseki

Energy Technology Data Exchange (ETDEWEB)

Kanbayashi, Y.; Okada, K. [Coal Mining Research Center, Tokyo (Japan)

1996-10-28

The relationship between coal properties and liquefaction or gasification characteristics was analyzed by using the analysis and test results and liquefaction characteristics in the coal data base. On liquefaction reaction, the close relation between an oil yield and coal constituent composition or a coal rank is well-known. Various multivariable regression analyses were conducted by using 6 factors as variables such as calorific value, volatile component, O/C and H/C atomic ratios, exinite+vitrinite content and vitrinite reflectance, and liquefaction characteristics as variate. On liquefaction characteristics, the oil yield of dehydrated and deashed coals, asphaltene yield, hydrogen consumption, produced water and gas quantities, and oil+asphaltene yield were predicted. The theoretical gasification efficiency of each specimen was calculated to evaluate the liquefaction reaction obtained. As a result, the oil yield increased with H/C atomic ratio, while the theoretical gasification efficiency increased with O/C atomic ratio. 5 figs., 1 tab.

The content and role of formal contracts in high-tech alliances

NARCIS (Netherlands)

de Jong, Gjalt; Woolthuis, Rosalinde Ja Klein

2009-01-01

In this study we investigate the governance structure of innovation processes in high-tech alliances, focusing on the content and role of formal contracts. The design of a formal agreement is one of the most important strategic decisions for alliance partners. Drawing upon transaction cost arguments

The treatment of large quantities of high fluorin contents UO2 by ammonium double uranate (ADU) techniques

International Nuclear Information System (INIS)

Wang Bangwu; Chen Ying

2010-01-01

The paper has discussed the sinter action of UO 2 in low temperature. The study indicates the over hot part of UO 2 by the deoxidization hot of oxidation uranate mostly results in the sinter in the process of trans form ADU into UO 2 . The UO 2 settling times in kiln little influences the sinter performance of UO 2 in the same condition of high fluorin contents UO 2 returning kiln, and high fluorin contents UO 2 returning kiln does not sinter UO 2 again. Experiment on large quantities of high fluorin contents UO 2 by Ammonium Double Uranate (ADU) techniques direct returning kiln, the result shows the sinter performance of UO 2 doesn't drop in the process of high fluor in contents UO 2 direct returning kiln, and the performance of UO 2 can meet specification. (authors)

Designing novel bulk metallic glass composites with a high aluminum content.

Science.gov (United States)

Chen, Z P; Gao, J E; Wu, Y; Wang, H; Liu, X J; Lu, Z P

2013-11-27

The long-standing challenge for forming Al-based BMGs and their matrix composites with a critical size larger than 1 mm have not been answered over the past three decades. In this paper, we reported formation of a series of BMG matrix composites which contain a high Al content up to 55 at.%. These composites can be cast at extraordinarily low cooling rates, compatible with maximum rod diameters of over a centimetre in copper mold casting. Our results indicate that proper additions of transition element Fe which have a positive heat of mixing with the main constituents La and Ce can appreciably improve the formability of the BMG matrix composites by suppressing the precipitation of Al(La,Ce) phase resulted from occurrence of the phase separation. However, the optimum content of Fe addition is strongly dependant on the total amount of the Al content in the Al-(CoCu)-(La,Ce) alloys.

High content analysis of phagocytic activity and cell morphology with PuntoMorph.

Science.gov (United States)

Al-Ali, Hassan; Gao, Han; Dalby-Hansen, Camilla; Peters, Vanessa Ann; Shi, Yan; Brambilla, Roberta

2017-11-01

Phagocytosis is essential for maintenance of normal homeostasis and healthy tissue. As such, it is a therapeutic target for a wide range of clinical applications. The development of phenotypic screens targeting phagocytosis has lagged behind, however, due to the difficulties associated with image-based quantification of phagocytic activity. We present a robust algorithm and cell-based assay system for high content analysis of phagocytic activity. The method utilizes fluorescently labeled beads as a phagocytic substrate with defined physical properties. The algorithm employs statistical modeling to determine the mean fluorescence of individual beads within each image, and uses the information to conduct an accurate count of phagocytosed beads. In addition, the algorithm conducts detailed and sophisticated analysis of cellular morphology, making it a standalone tool for high content screening. We tested our assay system using microglial cultures. Our results recapitulated previous findings on the effects of microglial stimulation on cell morphology and phagocytic activity. Moreover, our cell-level analysis revealed that the two phenotypes associated with microglial activation, specifically cell body hypertrophy and increased phagocytic activity, are not highly correlated. This novel finding suggests the two phenotypes may be under the control of distinct signaling pathways. We demonstrate that our assay system outperforms preexisting methods for quantifying phagocytic activity in multiple dimensions including speed, accuracy, and resolution. We provide a framework to facilitate the development of high content assays suitable for drug screening. For convenience, we implemented our algorithm in a standalone software package, PuntoMorph. Copyright © 2017 Elsevier B.V. All rights reserved.

Preparation of novel ceramics with high CaO content from steel slag

International Nuclear Information System (INIS)

Zhao, Lihua; Li, Yu; Zhou, Yuanyuan; Cang, Daqiang

2014-01-01

Highlights: • Efficiently utilize such solid waste with high CaO content. • A novel ceramics was put forward by traditional ceramic process. • The novel ceramics attained high strength. • Sintering mechanisms of the novel ceramics were discussed. - Abstract: Steel slag, an industrial waste discharged from steelmaking process, cannot be extensively used in traditional aluminosilicate based ceramics manufacturing for its high content of calcium oxide. In order to efficiently utilize such solid waste, a method of preparing ceramics with high CaO content was put forward. In this paper, steel slag in combination with quartz, talcum, clay and feldspar was converted to a novel ceramic by traditional ceramic process. The sintering mechanism, microstructure and performances were studied by scanning electron microscope (SEM), X-ray diffraction (XRD) techniques, combined experimenting of linear shrinkage, water absorption and flexural strength. The results revealed that all crystal phases in the novel ceramic were pyroxene group minerals, including diopsite ferrian, augite and diopsite. Almost all raw materials including quartz joined the reaction and transformed into pyroxene or glass phase in the sintering process, and different kinds of clays and feldspars had no impact on the final crystal phases. Flexural strength of the ceramic containing 40 wt.% steel slag in raw materials can reach 143 MPa at sintering temperature of 1210 °C and its corresponding water absorption, weight loss, linear shrinkage were 0.02%, 8.8%, 6.0% respectively. Pyroxene group minerals in ceramics would contribute to the excellent physical and mechanical properties

Study on microstructure and mechanical properties of Al–Mg–Si–Cu alloy with high manganese content

International Nuclear Information System (INIS)

Han, Yi; Ma, Ke; Li, Lian; Chen, Wei; Nagaumi, Hiromi

2012-01-01

Highlights: ► We examine the precipitates by HRTEM in the high manganese Al–Mg–Si–Cu alloy. ► Manganese content determines amount of secondary phases after homogenization. ► Increasing magnesium content promotes to precipitate S phase. ► Yield strength of the new alloy is 52–65% higher than that of commercial 6061 alloy. ► Uniform distribution of Mn dispersoids encourages to enhance mechanical properties. -- Abstract: The microstructure and mechanical properties of Al–Mg–Si–Cu alloy with high manganese content were studied in the present work to develop a new alloy. The microstructure features were quantificationally determined by a combination of scanning electron microscope and high resolution transmission electron microscopy. The dominant strengthening precipitates comprising the needle-shaped pre-β″(or β″) and lath-shaped Q′ phases were identified in the T6 temper. With the increase of magnesium content, S phase was promoted to precipitate to give an enhancement in strength. The yield strength of the examined alloys with high manganese content was found to be about 52–65% higher than that of commercial 6061 alloy. It was considered that, in addition to the strengthening precipitates, Mn dispersoids generating the dispersion hardening effect and the homogeneous deformation contributed a lot to the favorable mechanical properties.

A content analysis of tweets about high-potency marijuana.

Science.gov (United States)

Cavazos-Rehg, Patricia A; Sowles, Shaina J; Krauss, Melissa J; Agbonavbare, Vivian; Grucza, Richard; Bierut, Laura

2016-09-01

"Dabbing" involves heating extremely concentrated forms of marijuana to high temperatures and inhaling the resulting vapor. We studied themes describing the consequences of using highly concentrated marijuana by examining the dabbing-related content on Twitter. Tweets containing dabbing-related keywords were collected from 1/1-1/31/2015 (n=206,854). A random sample of 5000 tweets was coded for content according to pre-determined categories about dabbing-related behaviors and effects experienced using a crowdsourcing service. An examination of tweets from the full sample about respiratory effects and passing out was then conducted by selecting tweets with relevant keywords. Among the 5000 randomly sampled tweets, 3540 (71%) were related to dabbing marijuana concentrates. The most common themes included mentioning current use of concentrates (n=849; 24%), the intense high and/or extreme effects from dabbing (n=763; 22%) and excessive/heavy dabbing (n=517; 15%). Extreme effects included both physiological (n=124/333; 37%) and psychological effects (n=55/333; 17%). The most common physiologic effects, passing out (n=46/333; 14%) and respiratory effects (n=30/333; 9%), were then further studied in the full sample of tweets. Coughing was the most common respiratory effect mentioned (n=807/1179; 68%), and tweeters commonly expressed dabbing with intentions to pass out (416/915; 45%). This study adds to the limited understanding of marijuana concentrates and highlights self-reported physical and psychological effects from this type of marijuana use. Future research should further examine these effects and the potential severity of health consequences associated with concentrates. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Calcium content and high calcium adaptation of plants in karst areas of southwestern Hunan, China

Directory of Open Access Journals (Sweden)

X. Wei

2018-05-01

Full Text Available Rocky desertification is a major ecological problem of land degradation in karst areas. In these areas, the high soil calcium (Ca content has become an important environmental factor that can affect the restoration of vegetation. Consequently, the screening of plant species that can adapt to high Ca soil environments is a critical step in vegetation restoration. In this study, three grades of rocky desertification sample areas were selected in karst areas of southwestern Hunan, China (LRD: light rocky desertification; MRD: moderate rocky desertification; and IRD: intense rocky desertification. Each grade of these sample areas had three sample plots in different slope positions, each of which had four small quadrats (one in rocky-side areas, three in non-rocky-side areas. We measured the Ca content of leaves, branches, and roots from 41 plant species, as well as soil total Ca (TCa and exchangeable Ca (ECa at depths of 0–15, 15–30, and 30–45 cm in each small quadrat. The results showed that the soil Ca2+ content in rocky-side areas was significantly higher than that in non-rocky-side areas (p < 0.05. The mean soil TCa and ECa content increased gradually along with the grade of rocky desertification, in the order IRD > MRD > LRD. For all plant functional groups, the plant Ca content of aboveground parts was significantly higher than that of the belowground parts (p < 0.05. The soil ECa content had significant effects on plant Ca content of the belowground parts but had no significant effects on plant Ca content of the aboveground parts. Of the 41 plant species that were sampled, 17 were found to be dominant (important value > 1. The differences in Ca2+ content between the aboveground and belowground parts of the 17 dominant species were calculated, and their correlations with soil ECa content were analyzed. The results showed that these 17 species can be divided into three categories: Ca-indifferent plants, high

The combined use of micro-hydropyrolysis and compound-specific isotope analysis (CSIA) as a novel technique to identify coal-derived biodegraded PAH flux in the complex environment

Energy Technology Data Exchange (ETDEWEB)

Cheng-Gong Sun; Gbolagade Olalere; Wisdom Ivwurie; Mick Cooper; Colin Snape [University of Nottingham, Nottingham (United Kingdom). Nottingham Fuel and Energy Centre

2007-07-01

A novel analytical methodology combining CSIA and micro-hydropyrolysis (CSIA/micro-HyPy) has been developed to aid unambiguous source apportionment of PAHs in the complex environment where PAH matrices have been heavily biodegraded and/or their isotopic signatures are overlapping for some sources. Asphaltenes retain useful information of biogeochemical significance, which can be accessed via hydropyrolysis. The PAHs released from hydropyrolysis of asphaltenes, the bound PAHs, from different primary sources (e.g. crude oils, low and high temperature coal tars) were characterized and compared to free aromatics in regard to their molecular and 13C-isotopic profiles. It was found that hydropyrolysis of asphaltenes can generate molecular and isotopic profiles highly representative of their primary sources. For both low and high temperature coal tar, the bound aromatics have broadly similar molecular distributions to their free aromatic counterparts and have {sup 13}C-isotopic values almost identical to those of UK bituminous coals(-23{per_thousand}), indicating that the asphaltenes are actually released as representative fragments of coal structures during carbonization. As expected, the bound aromatics are more 13C-enriched by 1-3 {per_thousand} (-21 to -23{per_thousand}) compared to free aromatics (-24 to -26{per_thousand}). No significant isotopic difference was observed between free and bound aromatics for a North Sea crude oil, all having similar {sup 13}C-isotopic values (-27.2-30.2 {per_thousand}) that are significantly lighter than those for coal-derived aromatics. Applications of this novel methodological CSIA/micro-HyPy technique to samples previously examined from an area around a former carbonization plant have been successfully demonstrated where unambiguous source apportionment could not be achieved previously for the PAHs due to likely environmental alternation. 3 refs., 2 figs., 2 tabs.

Biobleaching chemistry of laccase-mediator systems on high-lignin-content kraft pulps

International Nuclear Information System (INIS)

Chakar, F.S.; Ragauskas, A.J.

2004-01-01

A high-lignin-content softwood kraft pulp was reacted with laccase in the presence of 1-hydroxybenzotriazole (HBT), N-acetyl-N-phenylhydroxylamine (NHA), and violuric acid (VA). The biodelignification response with violuric acid was superior to both 1-hydroxybenzotriazole and N-acetyl-N-phenylhydroxylamine. NMR analysis of residual lignins isolated before and after the biobleaching treatments revealed that the latter material was highly oxidized and that the magnitude of structural changes was most pronounced with the laccase - violuric acid biobleaching system. An increase in the content of carboxylic acid groups and a decrease in methoxyl groups were noted with all three laccase-mediator systems. The oxidation biobleaching pathway is directed primarily towards noncondensed C5 phenolic lignin functional structures for all three laccase-mediated systems. The laccase - violuric acid system was also reactive towards C5-condensed phenolic lignin structures. (author)

Vacuum Distillation Residue Upgrading by an Indigenous Bacillus Cereus

Directory of Open Access Journals (Sweden)

Mitra Sadat Tabatabaee

2013-07-01

Full Text Available Background:Biological processing of heavy fractions of crude oils offers less severe process conditions and higher selectivity for refining. Biochemical Processes are expected to be low demand energy processes and certainly ecofriendly.Results:A strain of biosurfactant producing bacterium was isolated from an oil contaminated soil at Tehran refinery distillation unit. Based on selected phenotypic and genotypic characteristic including morphology, biochemical proprety, and 16 SrRNA sequencing identified as a novel strain of Bacillus cereus (JQ178332. This bacterium endures a wide range of pH, salinity and temperature. This specific strain utilizes both paraffin and anthracene as samples of aliphatic and polycyclic aromatic hydrocarbons. The ability of this bacterium to acquire all its energy and chemical requirements from Vacuum Distillation Residue (VR, as a net sample of problematic hydrocarbons in refineries, was studied. SARA test ASTM D4124-01 revealed 65.5% decrease in asphaltenic, 22.1% in aliphatics and 30.3% in Aromatics content of the VR in MSM medium. Further results with 0.9% saline showed 55% decrease in asphaltene content and 2.1% Aromatics respectively.Conclusion:Remarkable abilities of this microorganism propose its application in an ecofriendly technology to upgrade heavy crude oils.

Stabilization of Model Crude Oil Emulsion using Different ...

African Journals Online (AJOL)

MBI

2015-12-31

Dec 31, 2015 ... interaction of asphaltene with the prepared model oils can be used as a ... techniques, microscopy, interfacial pressure, and ... conclusion that these compounds were asphaltene .... The emulsion may invert from oil in water.

Research Article

African Journals Online (AJOL)

2018-05-01

May 1, 2018 ... affect the oil recovery and its transportation processes [5]. Asphaltenes are .... petroleum fluids. Int. J. Oil, Gas Coal Technol., 2009, vol. ... chemical structure of asphaltenes from Algerian petroleum collected at different stages.

Synthetic Biomaterials to Rival Nature's Complexity-a Path Forward with Combinatorics, High-Throughput Discovery, and High-Content Analysis.

Science.gov (United States)

Zhang, Douglas; Lee, Junmin; Kilian, Kristopher A

2017-10-01

Cells in tissue receive a host of soluble and insoluble signals in a context-dependent fashion, where integration of these cues through a complex network of signal transduction cascades will define a particular outcome. Biomaterials scientists and engineers are tasked with designing materials that can at least partially recreate this complex signaling milieu towards new materials for biomedical applications. In this progress report, recent advances in high throughput techniques and high content imaging approaches that are facilitating the discovery of efficacious biomaterials are described. From microarrays of synthetic polymers, peptides and full-length proteins, to designer cell culture systems that present multiple biophysical and biochemical cues in tandem, it is discussed how the integration of combinatorics with high content imaging and analysis is essential to extracting biologically meaningful information from large scale cellular screens to inform the design of next generation biomaterials. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Autoclave-hardening slag-alkali binder with high water content

International Nuclear Information System (INIS)

Korenevskij, V.V.; Kozyrin, N.A.; Melikhova, N.I.; Narkevich, N.K.; Ryabov, G.G.

1987-01-01

The results of investigations into properties of slag-alkali binder, that may be used for concretes of reactor radiation and thermal shieldings, are presented. These concretes have increased chemical stability and mechanical strength, high content of chemically bound water (approximately 14%), that is not lost under heating up to 550 deg C. Dumping and granulated slags of blast-furnace process, sodium-bicarbonate-alkali fusion cake formed at burning of adipic acid residues, technical sodium hydroxide and sodium liquid glass are used as raw material for slag-alkali binder

A deep learning and novelty detection framework for rapid phenotyping in high-content screening

Science.gov (United States)

Sommer, Christoph; Hoefler, Rudolf; Samwer, Matthias; Gerlich, Daniel W.

2017-01-01

Supervised machine learning is a powerful and widely used method for analyzing high-content screening data. Despite its accuracy, efficiency, and versatility, supervised machine learning has drawbacks, most notably its dependence on a priori knowledge of expected phenotypes and time-consuming classifier training. We provide a solution to these limitations with CellCognition Explorer, a generic novelty detection and deep learning framework. Application to several large-scale screening data sets on nuclear and mitotic cell morphologies demonstrates that CellCognition Explorer enables discovery of rare phenotypes without user training, which has broad implications for improved assay development in high-content screening. PMID:28954863

Determination of oxygen content in high Tc superconductors by deuteron particle activation analysis

International Nuclear Information System (INIS)

Tao Zhenlan; Yao, Y.D.; Kao, Y.H.

1993-01-01

The experimental method for determining the oxygen content in high T c superconductors is described in detail. This method is applied to determination of oxygen content in high T c Y-Ba-Cu-O and Bi-Sr-Ca-Cu-O samples in which the stoichiometry is varied by reducing the copper and bismuth concentrations. The oxygen concentration is found to vary linearly with Cu(x = 0-0.2) and Bi (x = 0-0.4) deficiencies in YBa 2 Cu 3(1-x )O y and Bi 2(1-x) Sr 2 CaCu 2 O y respectively. X-ray powder diffraction measurements show that the compound of YBa 2 Cu 3(1-x) O y is orthorhombic in the variation range of x = 0-0.2

Seismic Performance Comparison of a High-Content SDA Frame and Standard RC Frame

OpenAIRE

van de Lindt, John W.; Rechan, R. Karthik

2011-01-01

This study presents the method and results of an experiment to study the seismic behavior of a concrete portal frame with fifty percent of its cement content replaced with a spray dryer ash (SDA). Based on multiple-shake-table tests, the high content SDA frame was found to perform as well as the standard concrete frame for two earthquakes exceeding design-level intensity earthquakes. Hence, from a purely seismic/structural standpoint, it may be possible to replace approximately fifty percen...

Deposition of heavy oil fractions: development of a computational tool to predict oil mixtures compatibility; Deposicao de fracoes pesadas do petroleo: desenvolvimento de uma ferramenta computacional para a previsao da compatibilidade de misturas de petroleo

Energy Technology Data Exchange (ETDEWEB)

Prucole, Elisia S.; Henriques, Fernanda P.; Silva, Leandro M.; Touma, Silvia L. [PETROBRAS S.A., Rio de de Janeiro, RJ (Brazil)

2008-07-01

The remarkable increase in production and processing of national heavy oils is a scenario in which the deposition problem of heavy oil fractions is important, leading to huge losses, not only in economical terms but also in regard to environmental aspects, and can occur in practically all areas of the oil industry. Thus, the knowledge about technology concerning this subject is essential. In terms of heavy fractions, the asphaltenes are the heaviest components of oil and have propensity to aggregate, flocculate, precipitate and be adsorbed on surfaces. The difficulties for modeling the behavior of asphaltenes phases occur because of the high uncertainties which take in the current knowledge about the asphaltenes, their structures, flocculation and precipitation mechanisms and the phenomenon reversibility. The main goal of this work is to propose a predictive methodology for oils compatibility. A fuzzy classifier was implemented in order to predict the compatibility of oil mixtures, assessing whether the mixture condition is stable or not. The results were satisfactory, indicating a good predictive power of the proposed computational tool. (author)

Breeding of a new potato variety 'Nagasaki Kogane' with high eating quality, high carotenoid content, and resistance to diseases and pests.

Science.gov (United States)

Sakamoto, Yu; Mori, Kazuyuki; Matsuo, Yuuki; Mukojima, Nobuhiro; Watanabe, Wataru; Sobaru, Norio; Tamiya, Seiji; Nakao, Takashi; Hayashi, Kazuya; Watanuki, Hitomi; Nara, Kazuhiro; Yamazaki, Kaoru; Chaya, Masataka

2017-06-01

'Nagasaki Kogane' is a new potato variety bred from a cross between 'Saikai 35' as a female parent and 'Saikai 33' as a male. 'Saikai 35' is resistant to bacterial wilt, contains the H1 and Ry chc genes for resistance to the potato cyst nematode (PCN) and potato virus Y (PVY), respectively, and has high carotenoid content, while 'Saikai 33' has large and high-yielding tubers and is resistant to both bacterial wilt and PCN. The carotenoid content of 'Nagasaki Kogane' is higher than that of 'Dejima', a common double cropping variety. The taste quality of steamed 'Nagasaki Kogane' is comparable to that of 'Inca-no-mezame' tubers, which has high levels of carotenoid, and superior to 'Nishiyutaka', another popular double cropping variety. 'Nagasaki Kogane' is suitable for French fries, because its tuber has high starch content. The marketable yield of 'Nagasaki Kogane' was higher than that of 'Inca-no-mezame' in spring cropping, although it was lower than that of 'Nishiyutaka' in double cropping regions. 'Nagasaki Kogane' tubers are larger on average than 'Inca-no-mezame' tubers in spring cropping. Moreover, the 'Nagasaki Kogane' variety is resistant to PCN and PVY, and exhibits a high level of resistance to bacterial wilt.

Relations between interfacial properties and heavy crude oil emulsions stability; Relations entre les proprietes interfaciales et la stabilite des emulsions de brut lourd

Energy Technology Data Exchange (ETDEWEB)

Hoebler-Poteau, S.

2006-02-15

Oil in water emulsions are currently being investigated to facilitate the transport of viscous heavy oils. The behavior of these emulsions is largely controlled by oil / water interfaces. The surface-active components of crude oil such as asphaltenes and naphthenic acids compete among themselves at these interfaces and also with possibly added synthetic surfactant emulsifier.Here, we present a study of dynamic interfacial tension and rheology of interfaces between water and a model oil (toluene) in which asphaltenes and other surface active molecules from crude oil are dissolved. We show that different parameters such as aging of the interface, asphaltenes concentration, the pH and salinity of the aqueous phase have a strong influence on interfacial properties of asphaltenes at the oil/water interface. Several micro-pipette experiments, in which micrometric drops have been manipulated, are described as well as small angle neutron scattering measurements. The influence of lower molecular weight surface-active species, such as the natural naphthenic acids contained in maltenes (crude oil without asphaltenes) has been investigated, and an interaction between asphaltenes and maltenes which facilitates molecular arrangement at the interface was detected. The microscopic properties of the different interfaces and the stability of the corresponding emulsions are determined to be correlated.The results obtained on model emulsions and model oil/water interfaces were found to be helpful in order to explain and predict the behavior of heavy crude oil emulsions. (author)

Determination of oxygen content in high T/sub c/ superconductors by a charged particle activation method

International Nuclear Information System (INIS)

Tao, Z.; Alburger, D.E.; Jones, K.W.; Yao, Y.D.; Kao, Y.H.

1988-01-01

A new method for determining the oxygen content in high T/sub c/ superconductors has been demonstrated using a charged particle activation technique. This method allows a measurement of the concentration of 16 O atoms in the superconducting material by detection of the 17 F produced with the 16 O(d,n) 17 F nuclear reaction. By way of example, this technique is applied to the determination of oxygen content in a series of high T/sub c/ Y-Ba-Cu-O samples in which the stoichiometry is varied by reducing the copper concentration. The stabilized oxygen content shows a nonlinear dependence on the copper deficiency in these specimens

Effect of high hydrogen content on metallurgical and mechanical properties of zirconium alloy claddings after heat-treatment at high temperature

International Nuclear Information System (INIS)

Turque, Isabelle

2016-01-01

Under hypothetical loss-of-coolant accident conditions, fuel cladding tubes made of zirconium alloys can be exposed to steam at high temperature (HT, up 1200 C) before being cooled and then quenched in water. In some conditions, after burst occurrence the cladding can rapidly absorb a significant amount of hydrogen (secondary hydriding), up to 3000 wt.ppm locally, during steam exposition at HT. The study deals with the effect, poorly studied up to date, of high contents of hydrogen on the metallurgical and mechanical properties of two zirconium alloys, Zircaloy-4 and M5, during and after cooling from high temperatures, at which zirconium is in its β phase. A specific facility was developed to homogeneously charge in hydrogen up to ∼ 3000 wt.ppm cladding tube samples of several centimeters in length. Phase transformations, chemical element partitioning and hydrogen precipitation during cooling from the β temperature domain of zirconium were studied by using several techniques, for the materials containing up to ∼ 3000 wt.ppm of hydrogen in average: in-situ neutron diffraction upon cooling from 700 C, X-ray diffraction, μ-ERDA, EPMA and electron microscopy in particular. The results were compared to thermodynamic predictions. In order to study the effect of high hydrogen contents on the mechanical behavior of the (prior-)μ phase of zirconium, axial tensile tests were performed at various temperatures between 20 and 700 C upon cooling from the β temperature domain, on samples with mean hydrogen contents up to ∼ 3000 wt.ppm. The results show that metallurgical and mechanical properties of the (prior-)β phase of zirconium alloys strongly depend on temperature and hydrogen content. (author) [fr

Nanoscale high-content analysis using compositional heterogeneities of single proteoliposomes

DEFF Research Database (Denmark)

Mathiasen, Signe; Christensen, Sune M.; Fung, Juan José

2014-01-01

Proteoliposome reconstitution is a standard method to stabilize purified transmembrane proteins in membranes for structural and functional assays. Here we quantified intrareconstitution heterogeneities in single proteoliposomes using fluorescence microscopy. Our results suggest that compositional...... heterogeneities can severely skew ensemble-average proteoliposome measurements but also enable ultraminiaturized high-content screens. We took advantage of this screening capability to map the oligomerization energy of the β2-adrenergic receptor using ∼10(9)-fold less protein than conventional assays....

Effect of PVA fiber content on creep property of fiber reinforced high-strength concrete columns

Science.gov (United States)

Xu, Zongnan; Wang, Tao; Wang, Weilun

2018-04-01

The effect of PVA (polyvinyl alcohol) fiber content on the creep property of fiber reinforced high-strength concrete columns was investigated. The correction factor of PVA fiber content was proposed and the creep prediction model of ACI209 was modified. Controlling the concrete strength as C80, changing the content of PVA fiber (volume fraction 0%, 0.25%, 0.5%, 1% respectively), the creep experiment of PVA fiber reinforced concrete columns was carried out, the creep coefficient of each specimen was calculated to characterize the creep property. The influence of PVA fiber content on the creep property was analyzed based on the creep coefficient and the calculation results of several frequently used creep prediction models. The correction factor of PVA fiber content was proposed to modify the ACI209 creep prediction model.

FeNbB bulk metallic glass with high boron content

Energy Technology Data Exchange (ETDEWEB)

Stoica, M.; Das, Jayanta; Eckert, Juergen [IFW Dresden, Institute for Complex Materials, P.O. Box 270016, D-01171 Dresden (Germany); Hajlaoui, Khalil; Yavari, Alain Reza [LTPCM-CNRS, I.N.P. Grenoble, 1130 Rue de la Piscine, BP 75, F-38402 University Campus (France)

2007-07-01

Fe-based alloys able to form magnetic bulk metallic glasses (BMGs) are of the type transition metal - metalloid and often contain 5 or more elements. Usually, the metalloid content is around 20 atomic %. Very recently, the Fe{sub 66}Nb{sub 4}B{sub 30} alloy was found to be able to form BMG by copper mold casting technique, despite its high metalloid content. Several composition with boron contents around 30 at. % or even higher were calculated since 1993 as possible compositions of the remaining amorphous matrix after the first stage of nanocrystallization of Finemet-type Fe{sub 77}Si{sub 14}B{sub 9} glassy ribbons with 0.5 to 1 atomic % Cu and a few percent Nb addition. Melt-spun ribbons of all calculated compositions were found to be glassy. The composition of the ternary Fe-based BMG investigated in the present study resulted as an optimization of all possibilities. The alloy is ferromagnetic with glass transition temperature T{sub g}=845 K, crystallisation temperature T{sub x}=876 K, liquidus temperature T{sub liq}=1451 K and mechanical strength of 4 GPa. The coercivity of as-cast samples is very low, around 1.5 A/m. The present contribution aims at discussing the thermal stability, mechanical and magnetic properties of the Fe{sub 66}Nb{sub 4}B{sub 30} BMG.

Calcium content and high calcium adaptation of plants in karst areas of southwestern Hunan, China

Science.gov (United States)

Wei, Xiaocong; Deng, Xiangwen; Xiang, Wenhua; Lei, Pifeng; Ouyang, Shuai; Wen, Hongfang; Chen, Liang

2018-05-01

Rocky desertification is a major ecological problem of land degradation in karst areas. In these areas, the high soil calcium (Ca) content has become an important environmental factor that can affect the restoration of vegetation. Consequently, the screening of plant species that can adapt to high Ca soil environments is a critical step in vegetation restoration. In this study, three grades of rocky desertification sample areas were selected in karst areas of southwestern Hunan, China (LRD: light rocky desertification; MRD: moderate rocky desertification; and IRD: intense rocky desertification). Each grade of these sample areas had three sample plots in different slope positions, each of which had four small quadrats (one in rocky-side areas, three in non-rocky-side areas). We measured the Ca content of leaves, branches, and roots from 41 plant species, as well as soil total Ca (TCa) and exchangeable Ca (ECa) at depths of 0-15, 15-30, and 30-45 cm in each small quadrat. The results showed that the soil Ca2+ content in rocky-side areas was significantly higher than that in non-rocky-side areas (p desertification, in the order IRD > MRD > LRD. For all plant functional groups, the plant Ca content of aboveground parts was significantly higher than that of the belowground parts (p 1). The differences in Ca2+ content between the aboveground and belowground parts of the 17 dominant species were calculated, and their correlations with soil ECa content were analyzed. The results showed that these 17 species can be divided into three categories: Ca-indifferent plants, high-Ca plants, and low-Ca plants. These findings provide a vital theoretical basis and practical guide for vegetation restoration and ecosystem reconstruction in rocky desertification areas.

Synthesis and properties of hydroxy acrylic resin with high solid content

Science.gov (United States)

Yu, Zhen; Hu, Mingguang; Cui, Han; Xiao, Jijun

2017-10-01

Manufacturers of automotive repair finishes are tending to reduce more and more the level of volatile organic compounds in their paints in order to comply with increasingly strict environmental legislation. A high solid hydroxy acrylic resin was synthesised using CARDURA E10 and a type of hydroxyacrylic acid resin, its' acid value, hydroxylvalue, viscosity, structure, morphology was measured and film-forming properties after curing were characterised. The results show that the addition of CARDURA E10 in the copolymer composition significantly reduced the viscosity of the polymer system, improved the solid content of the resin and the physical properties of the coating. The hydroxyl acrylate resin with solid content of 90% and excellent comprehensive performance were successfully prepared by controlling the initiator dosage, polymerization temperature and monomer ratio.

Seismic Performance Comparison of a High-Content SDA Frame and Standard RC Frame

Directory of Open Access Journals (Sweden)

John W. van de Lindt

2011-01-01

Full Text Available This study presents the method and results of an experiment to study the seismic behavior of a concrete portal frame with fifty percent of its cement content replaced with a spray dryer ash (SDA. Based on multiple-shake-table tests, the high content SDA frame was found to perform as well as the standard concrete frame for two earthquakes exceeding design-level intensity earthquakes. Hence, from a purely seismic/structural standpoint, it may be possible to replace approximately fifty percent of cement in a concrete mix with SDA for the construction of structural members in high seismic zones. This would help significantly redirect spray dryer ash away from landfills, thus, providing a sustainable greener alternative to concrete that uses only Portland cement, or only a small percentage of SDA or fly ash.

Content Analysis of the Concept of Addiction in High School Textbooks of Iran.

Science.gov (United States)

Mirzamohammadi, Mohammad Hasan; Mousavi, Sayedeh Zainab; Massah, Omid; Farhoudian, Ali

2017-01-01

This research sought to determine how well the causes of addiction, addiction harms, and prevention of addiction have been noticed in high school textbooks. We used descriptive method to select the main related components of the addiction concept and content analysis method for analyzing the content of textbooks. The study population comprised 61 secondary school curriculum textbooks and study sample consisted of 14 secondary school textbooks selected by purposeful sampling method. The tools for collecting data were "content analysis inventory" which its validity was confirmed by educational and social sciences experts and its reliability has been found to be 91%. About 67 components were prepared for content analysis and were divided to 3 categories of causes, harms, and prevention of addiction. The analysis units in this study comprised phrases, topics, examples, course topics, words, poems, images, questions, tables, and exercises. Results of the study showed that the components of the addiction concept have presented with 212 remarks in the textbooks. Also, the degree of attention given to any of the 3 main components of the addiction concept were presented as follows: causes with 52 (24.52%) remarks, harm with 89 (41.98%) remarks, and prevention with 71 (33.49%) remarks. In high school textbooks, little attention has been paid to the concept of addiction and mostly its biological dimension were addressed while social, personal, familial, and religious dimensions of addiction have been neglected.

Design of a small scale boiler package for testing high moisture content biofuels

Energy Technology Data Exchange (ETDEWEB)

Proctor, Andrew

2005-07-01

This report presents the results of a project to design a prototype, small-scale boiler (0.88 MWth output) to enable clean and efficient combustion of high moisture content (>30%) biomass fuels. The boiler was based on an open bottom smoke tube design, modified to incorporate water tubes in the combustion chamber running from front to back. These were added to support refractory bricks to create an extra pass in the boiler combustion chamber such that the reflected heat from the refractory increased the rate of evaporation of moisture from the fuel. A chain grate stoker was employed. The combustion tests involved three biofuels: wood pellets with a low moisture content (8-10%) (to provide combustion rates for a commercially proven biofuel); wood chips from forestry waste with a 30-40% moisture content; and spent mushroom compost with 70-75% moisture. The tests on the wood chips required a number of modifications to the fuel feeding system and to the boiler in order to achieve limited success and the tests with the mushroom compost were unsuccessful due to the combination of the high moisture content and the fuel's low calorific value. Experience gained with the wood chips suggested a number of improvements for a future boiler design. As well as describing the experimental work and test results, the report offers an economic analysis (capital costs, fuel costs, running costs) of the scheme.

A one-step bioprocess for production of high-content fructo-oligosaccharides from inulin by yeast.

Science.gov (United States)

Wang, Da; Li, Fu-Li; Wang, Shi-An

2016-10-20

Commercial fructo-oligosaccharides (FOS) are predominantly produced from sucrose by transfructosylation process that presents a maximum theoretical yield below 0.60gFOSgSucrose(-1). To obtain high-content FOS, costly purification is generally employed. Additionally, high-content FOS can be produced from inulin by using endo-inulinases. However, commercial endo-inulinases have not been extensively used in scale-up production of FOS. In the present study, a one-step bioprocess that integrated endo-inulinase production, FOS fermentation, and non-FOS sugars removal into one reactor was proposed to produce high-content FOS from inulin. The bioprocess was implemented by a recombinant yeast strain JZHΔS-TSC, in which a heterologous endo-inulinase gene was expressed and the inherent invertase gene SUC2 was disrupted. FOS fermentation at 40°C from 200g/L chicory inulin presented the maximun titer, yield, and productivity of 180.2±0.8g/L, 0.9gFOSgInulin(-1), and 7.51±0.03g/L/h, respectively. This study demonstrated that the one-step bioprocess was simple and highly efficient. Copyright © 2016 Elsevier Ltd. All rights reserved.

Nitrogen-fixing cyanobacterium with a high phycoerythrin content.

Science.gov (United States)

Rodriguez, H; Rivas, J; Guerrero, M G; Losada, M

1989-03-01

The elemental and molecular composition, pigment content, and productivity of a phycoerythrin-rich nitrogen-fixing cyanobacterium-an Anabaena strain isolated from the coastal lagoon Albufera de Valencia, Spain-has been investigated. When compared with other heterocystous species, this strain exhibits similar chlorophyll a, carotene, and total phycobiliprotein contents but differs remarkably in the relative proportion of specific phycobiliproteins; the content of C-phycoerythrin amounts to 8.3% (versus about 1% in the other species) of cell dry weight. Absorption and fluorescence spectra of intact phycobilisomes isolated from this Anabaena sp. corroborate the marked contribution of phycoerythrin as an antenna pigment, a circumstance that is unusual for cyanobacteria capable of fixing N(2). The pigment content of cells is affected by variations in irradiance and cell density, these adaptive changes being more patent for C-phycoerythrin than for phycocyanins. The Anabaena strain is clumpy and capable of rapid flocculation. It exhibits outdoor productivities higher than 20 g (dry weight) m day during summer.

Iron content and solubility in dust from high-alpine snow along a north-south transect of High Asia

OpenAIRE

Wu, Guangjian; Zhang, Chenglong; Li, Zhongqin; Zhang, Xuelei; Gao, Shaopeng

2012-01-01

This study describes the dissolved and insoluble iron fraction of dust (mineral aerosol) in high-alpine snow samples collected along a north-south transect across High Asia (Eastern Tien Shan, Qilian Shan, and Southern Tibetan Plateau). This dust provides the basic chemical properties of mid- and high-level tropospheric Asian dust that can supply the limiting iron nutrient for phytoplankton growth in the North Pacific. The iron content in Asian dust averages 4.95% in Eastern Tien Shan, 3.38–5...

Permeability Damage Due to Asphaltene Deposition : Experimental and Modeling Aspects Endommagement d'un milieu poreux par dépôts d'asphaltènes : expériences et modélisation

Directory of Open Access Journals (Sweden)

Minssieux L.

2006-12-01

Full Text Available The flow properties of several asphaltenic crudes were studied at reservoir temperature in rocks of different morphology and mineralogy. The experiments performed showed a progressive reduction in permeability to oil during injection, varying in rate according to the system considered. The existence of organic deposits was verified by Rock-Evalpyrolysis measurements made on sections of samples taken at the end of flow at different distances from the entry face. This technique enables the profile of the deposits to be quantified. The interpretation of the permeability damage experiments and their simulation are treated by comparing the asphaltenes in oil to colloidal particles in suspension, capable of being deposited at the surface of the pores and thus reducing the permeability of the porous medium. The first simulations were carried out using the PARISIFP particle damage model, which has recently been extended to the case of multi-layer deposition. A satisfactory qualitative agreement is observed with the experimental results. Les propriétés d'écoulement de plusieurs bruts asphalténiques ont été étudiées à la température du réservoir d'origine dans des roches de morphologie et minéralogie différentes. Les expériences réalisées mettent en évidence une réduction progressive de la perméabilité à l'huile au cours de l'injection, plus ou moins rapide selon les cas. L'existence de dépôts organiques a été vérifiée par des mesures de pyrolyse Rock-Evaleffectuées sur des sections d'échantillons prélevées en fin d'écoulement à différentes distances de la face d'entrée. Cette technique permet de quantifier le profil des dépôts. L'interprétation des expériences de colmatage et leur simulation sont traitées en assimilant les asphaltènes dans l'huile à des particules colloïdales en suspension, susceptibles de se déposer à la surface des pores et ainsi de réduire la perméabilité du milieu poreux. Les premi

Innovation management and marketing in the high-tech sector: A content analysis of advertisements

DEFF Research Database (Denmark)

Gerhard, D.; Brem, Alexander; Baccarella, Ch.

2011-01-01

Advertizing high-technology products is a tricky and critical task for every company, since it means operating in an environment with high market uncertainty. The work presents results of a content analysis of 110 adverts for consumer electronics products which examines how these products and the...

Model compounds for heavy crude oil components and tetrameric acids: Characterization and interfacial behaviour

Energy Technology Data Exchange (ETDEWEB)

Nordgaard, Erland Loeken

2009-07-01

The tendency during the past decades in the quality of oil reserves shows that conventional crude oil is gradually being depleted and the demand being replaced by heavy crude oils. These oils contain more of a class high-molecular weight components termed asphaltenes. This class is mainly responsible for stable water-in-crude oil emulsions. Both heavy and lighter crude oils in addition contain substantial amounts of naphthenic acids creating naphthenate deposits in topside facilities. The asphaltene class is defined by solubility and consists of several thousand different structures which may behave differently in oil-water systems. The nature of possible sub fractions of the asphaltene has been received more attention lately, but still the properties and composition of such is not completely understood. In this work, the problem has been addressed by synthesizing model compounds for the asphaltenes, on the basis that an acidic function incorporated could be crucial. Such acidic, poly aromatic surfactants turned out to be highly inter facially active as studied by the pendant drop technique. Langmuir monolayer compressions combined with fluorescence of deposited films indicated that the interfacial activity was a result of an efficient packing of the aromatic cores in the molecules, giving stabilizing interactions at the o/w interface. Droplet size distributions of emulsions studied by PFG NMR and adsorption onto hydrophilic silica particles demonstrated the high affinity to o/w interfaces and that the efficient packing gave higher emulsion stability. Comparing to a model compound lacking the acidic group, it was obvious that sub fractions of asphaltenes that contain an acidic, or maybe similar hydrogen bonding functions, could be responsible for stable w/o emulsions. Indigenous tetrameric acids are the main constituent of calcium naphthenate deposits. Several synthetic model tetra acids have been prepared and their properties have been compared to the indigenous

HC StratoMineR: A Web-Based Tool for the Rapid Analysis of High-Content Datasets.

Science.gov (United States)

Omta, Wienand A; van Heesbeen, Roy G; Pagliero, Romina J; van der Velden, Lieke M; Lelieveld, Daphne; Nellen, Mehdi; Kramer, Maik; Yeong, Marley; Saeidi, Amir M; Medema, Rene H; Spruit, Marco; Brinkkemper, Sjaak; Klumperman, Judith; Egan, David A

2016-10-01

High-content screening (HCS) can generate large multidimensional datasets and when aligned with the appropriate data mining tools, it can yield valuable insights into the mechanism of action of bioactive molecules. However, easy-to-use data mining tools are not widely available, with the result that these datasets are frequently underutilized. Here, we present HC StratoMineR, a web-based tool for high-content data analysis. It is a decision-supportive platform that guides even non-expert users through a high-content data analysis workflow. HC StratoMineR is built by using My Structured Query Language for storage and querying, PHP: Hypertext Preprocessor as the main programming language, and jQuery for additional user interface functionality. R is used for statistical calculations, logic and data visualizations. Furthermore, C++ and graphical processor unit power is diffusely embedded in R by using the rcpp and rpud libraries for operations that are computationally highly intensive. We show that we can use HC StratoMineR for the analysis of multivariate data from a high-content siRNA knock-down screen and a small-molecule screen. It can be used to rapidly filter out undesirable data; to select relevant data; and to perform quality control, data reduction, data exploration, morphological hit picking, and data clustering. Our results demonstrate that HC StratoMineR can be used to functionally categorize HCS hits and, thus, provide valuable information for hit prioritization.

Effects of carbon content on high-temperature mechanical and thermal fatigue properties of high-boron austenitic steels

Directory of Open Access Journals (Sweden)

Xiang Chen

2016-01-01

Full Text Available High-temperature mechanical properties of high-boron austenitic steels (HBASs were studied at 850 °C using a dynamic thermal-mechanical simulation testing machine. In addition, the thermal fatigue properties of the alloys were investigated using the self-restraint Uddeholm thermal fatigue test, during which the alloy specimens were cycled between room temperature and 800°C. Stereomicroscopy and scanning electron microscopy were used to study the surface cracks and cross-sectional microstructure of the alloy specimens after the thermal fatigue tests. The effects of carbon content on the mechanical properties at room temperature and high-temperature as well as thermal fatigue properties of the HBASs were also studied. The experimental results show that increasing carbon content induces changes in the microstructure and mechanical properties of the HBASs. The boride phase within the HBAS matrix exhibits a round and smooth morphology, and they are distributed in a discrete manner. The hardness of the alloys increases from 239 (0.19wt.% C to 302 (0.29wt.% C and 312 HV (0.37wt.% C; the tensile yield strength at 850 °C increases from 165.1 to 190.3 and 197.1 MPa; and the compressive yield strength increases from 166.1 to 167.9 and 184.4 MPa. The results of the thermal fatigue tests (performed for 300 cycles from room temperature to 800 °C indicate that the degree of thermal fatigue of the HBAS with 0.29wt.% C (rating of 2–3 is superior to those of the alloys with 0.19wt.% (rating of 4–5 and 0.37wt.% (rating of 3–4 carbon. The main cause of this difference is the ready precipitation of M23(C,B6-type borocarbides in the alloys with high carbon content during thermal fatigue testing. The precipitation and aggregation of borocarbide particles at the grain boundaries result in the deterioration of the thermal fatigue properties of the alloys.

The development of high-content screening (HCS) technology and its importance to drug discovery.

Science.gov (United States)

Fraietta, Ivan; Gasparri, Fabio

2016-01-01

High-content screening (HCS) was introduced about twenty years ago as a promising analytical approach to facilitate some critical aspects of drug discovery. Its application has spread progressively within the pharmaceutical industry and academia to the point that it today represents a fundamental tool in supporting drug discovery and development. Here, the authors review some of significant progress in the HCS field in terms of biological models and assay readouts. They highlight the importance of high-content screening in drug discovery, as testified by its numerous applications in a variety of therapeutic areas: oncology, infective diseases, cardiovascular and neurodegenerative diseases. They also dissect the role of HCS technology in different phases of the drug discovery pipeline: target identification, primary compound screening, secondary assays, mechanism of action studies and in vitro toxicology. Recent advances in cellular assay technologies, such as the introduction of three-dimensional (3D) cultures, induced pluripotent stem cells (iPSCs) and genome editing technologies (e.g., CRISPR/Cas9), have tremendously expanded the potential of high-content assays to contribute to the drug discovery process. Increasingly predictive cellular models and readouts, together with the development of more sophisticated and affordable HCS readers, will further consolidate the role of HCS technology in drug discovery.

Microstructure Characteristics of High Lift Factor MOCVD REBCO Coated Conductors With High Zr Content

Energy Technology Data Exchange (ETDEWEB)

Galstyan, E; Gharahcheshmeh, MH; Delgado, L; Xu, AX; Majkic, G; Selvamanickam, V

2015-06-01

We report the microstructural characteristics of high levels of Zr-added REBa2Cu3O7-x (RE = Gd, Y rare earth) coated conductors fabricated by Metal Organic Chemical Vapor Deposition (MOCVD). The enhancements of the lift factor defined as a ratio of the in-field (3 T, B parallel to c-axis) critical current density (J(c)) at 30 K and self-field J(c) at 77 K have been achieved for Zr addition levels of 20 and 25 mol% via optimization of deposition parameters. The presence of strong flux pinning is attributed to the aligned nanocolumns of BaZrO3 and nanoprecipitates embedded in REBa2Cu3O7-x matrix with good crystal quality. A high density of BZO nanorods with a typical size 6-8 nm and spacing of 20 nm has been observed. Moreover, the high Zr content was found to induce a high density of intrinsic defects, including stacking faults and dislocations. The correlation between in-field performance along the c-axis and microstructure of (Gd, Y) BCO film with a high level of Zr addition is discussed.

A Categorical Content Analysis of Highly Cited Literature Related to Trends and Issues in Special Education.

Science.gov (United States)

Arden, Sarah V; Pentimonti, Jill M; Cooray, Rochana; Jackson, Stephanie

2017-07-01

This investigation employs categorical content analysis processes as a mechanism to examine trends and issues in a sampling of highly cited (100+) literature in special education journals. The authors had two goals: (a) broadly identifying trends across publication type, content area, and methodology and (b) specifically identifying articles with disaggregated outcomes for students with learning disabilities (LD). Content analyses were conducted across highly cited (100+) articles published during a 20-year period (1992-2013) in a sample ( n = 3) of journals focused primarily on LD, and in one broad, cross-categorical journal recognized for its impact in the field. Results indicated trends in the article type (i.e., commentary and position papers), content (i.e., reading and behavior), and methodology (i.e., small proportions of experimental and quasi-experimental designs). Results also revealed stability in the proportion of intervention research studies when compared to previous analyses and a decline in the proportion of those that disaggregated data specifically for students with LD.

Interaction genotype by season and its influence on the identification of beans with high content of zinc and iron

Directory of Open Access Journals (Sweden)

Camila Andrade Silva

2012-01-01

Full Text Available The mineral contents in common bean seeds are influenced, in addition to genetic variation, by environmental crop conditions, especially by the soil type and chemical composition and by the genotype x environment interaction. This study was carried out to verify if the zinc and iron contents are affected by the crop growing period. Ten lines with high iron and zinc contents and ten with low contents were assessed in three seasons: "wet season" of 2009/2010 (sowing in November; "dry season" of 2010 (sowing in February and "winter season" of 2010 (sowing in July, in Lavras, Minas Gerais State, Brazil. The experimental design used was randomized blocks with three replications and plots consisting of two rows of two meters, with a spacing of 0.50 m. The seeds harvested were assessed in regard to iron and zinc mineral contents. The greatest contents were observed in the winter season and the smallest ones in the dry season, with sowing in February. It was observed that in the mean of the three harvests, the lines classified as having high iron and zinc content exhibited an iron quantity 11.0% and a zinc quantity 6.8% above those of low content. The lines by seasons interaction occurs. However, its interference in identification of the groups with high and low content of the two nutrients is not great.

Improvement of cassava for high dry matter, starch and low cyanogenic glucoside content by mutation induction

Energy Technology Data Exchange (ETDEWEB)

Nwachukwu, E C; Mbanaso, E N.A.; Ene, L S.O. [Plant Breeding Div., National Root Crops Research Inst., Umudike, Umuahia (Nigeria)

1997-07-01

Cassava (Manihot esculenta Crantz) is an important food in Nigeria. One drawback in its use as a staple food is the presence of cyanogenic glucosides which on hydrolysis produce the very toxic hydrogen cyanide (HCN). To reduce the cyanogenic levels by mutation induction, three locally adopted and high yielding varieties of cassava, TMS 30572, NR 8817 and NR 84111 were irradiated with 20, 25 and 30 Gy gamma rays. There were a wide variation in HCN, dry matter and starch content of irradiated cassava plants, screened in the MV{sub 2} propagation. Fourteen cassavavariant lines were selected for low HCN content, and 22 lines for high dry matter content. These will be further tested for yield in replicated field trials. (author). 7 refs, 3 tabs.

Improvement of cassava for high dry matter, starch and low cyanogenic glucoside content by mutation induction

International Nuclear Information System (INIS)

Nwachukwu, E.C.; Mbanaso, E.N.A.; Ene, L.S.O.

1997-01-01

Cassava (Manihot esculenta Crantz) is an important food in Nigeria. One drawback in its use as a staple food is the presence of cyanogenic glucosides which on hydrolysis produce the very toxic hydrogen cyanide (HCN). To reduce the cyanogenic levels by mutation induction, three locally adopted and high yielding varieties of cassava, TMS 30572, NR 8817 and NR 84111 were irradiated with 20, 25 and 30 Gy gamma rays. There were a wide variation in HCN, dry matter and starch content of irradiated cassava plants, screened in the MV 2 propagation. Fourteen cassavavariant lines were selected for low HCN content, and 22 lines for high dry matter content. These will be further tested for yield in replicated field trials. (author). 7 refs, 3 tabs

Anti-cancer agents in Saudi Arabian herbals revealed by automated high-content imaging

KAUST Repository

Hajjar, Dina A.; Kremb, Stephan Georg; Sioud, Salim; Emwas, Abdul-Hamid M.; Voolstra, Christian R.; Ravasi, Timothy

2017-01-01

in cancer therapy. Here, we used cell-based phenotypic profiling and image-based high-content screening to study the mode of action and potential cellular targets of plants historically used in Saudi Arabia's traditional medicine. We compared the cytological

Exceptional heat stability of high protein content dispersions containing whey protein particles

NARCIS (Netherlands)

Saglam, D.; Venema, P.; Vries, de R.J.; Linden, van der E.

2014-01-01

Due to aggregation and/or gelation during thermal treatment, the amount of whey proteins that can be used in the formulation of high protein foods e.g. protein drinks, is limited. The aim of this study was to replace whey proteins with whey protein particles to increase the total protein content and

Materials development and field demonstration of high-recycled-content concrete for energy-efficient building construction; FINAL

International Nuclear Information System (INIS)

Ostowari, Ken; Nosson, Ali

2000-01-01

The project developed high-recycled-content concrete material with balanced structural and thermal attributes for use in energy-efficient building construction. Recycled plastics, tire, wool, steel and concrete were used as replacement for coarse aggregates in concrete and masonry production. With recycled materials the specific heat and thermal conductivity of concrete could be tailored to enhance the energy-efficiency of concrete buildings. A comprehensive field project was implemented which confirmed the benefits of high-recycled-content concrete for energy-efficient building construction

The potential of a high protein-low carbohydrate diet to preserve intrahepatic triglyceride content in healthy humans.

Science.gov (United States)

Martens, Eveline A; Gatta-Cherifi, Blandine; Gonnissen, Hanne K; Westerterp-Plantenga, Margriet S

2014-01-01

Protein supplementation has been shown to reduce the increases in intrahepatic triglyceride (IHTG) content induced by acute hypercaloric high-fat and high-fructose diets in humans. To assess the effect of a 12-wk iso-energetic high protein-low carbohydrate (HPLC) diet compared with an iso-energetic high carbohydrate-low protein (HCLP) diet on IHTG content in healthy non-obese subjects, at a constant body weight. Seven men and nine women [mean ± SD age: 24 ± 5 y; BMI: 22.9 ± 2.1 kg/m2] were randomly allocated to a HPLC [30/35/35% of energy (En%) from protein/carbohydrate/fat] or a HCLP (5/60/35 En%) diet by stratification on sex, age and BMI. Dietary guidelines were prescribed based on individual daily energy requirements. IHTG content was measured by 1H-magnetic resonance spectroscopy before and after the dietary intervention. IHTG content changed in different directions with the HPLC (CH2H2O: 0.23 ± 0.17 to 0.20 ± 0.10; IHTG%: 0.25 ± 0.20% to 0.22 ± 0.11%) compared with the HCLP diet (CH2H2O: 0.34 ± 0.20 vs. 0.38 ± 0.21; IHTG%: 0.38 ± 0.22% vs. 0.43 ± 0.24%), which resulted in a lower IHTG content in the HPLC compared with the HCLP diet group after 12 weeks, which almost reached statistical significance (P = 0.055). A HPLC vs. a HCLP diet has the potential to preserve vs. enlarge IHTG content in healthy non-obese subjects at a constant body weight. Clinicaltrials.gov NCT01551238.

The potential of a high protein-low carbohydrate diet to preserve intrahepatic triglyceride content in healthy humans.

Directory of Open Access Journals (Sweden)

Eveline A Martens

Full Text Available Protein supplementation has been shown to reduce the increases in intrahepatic triglyceride (IHTG content induced by acute hypercaloric high-fat and high-fructose diets in humans.To assess the effect of a 12-wk iso-energetic high protein-low carbohydrate (HPLC diet compared with an iso-energetic high carbohydrate-low protein (HCLP diet on IHTG content in healthy non-obese subjects, at a constant body weight.Seven men and nine women [mean ± SD age: 24 ± 5 y; BMI: 22.9 ± 2.1 kg/m2] were randomly allocated to a HPLC [30/35/35% of energy (En% from protein/carbohydrate/fat] or a HCLP (5/60/35 En% diet by stratification on sex, age and BMI. Dietary guidelines were prescribed based on individual daily energy requirements. IHTG content was measured by 1H-magnetic resonance spectroscopy before and after the dietary intervention.IHTG content changed in different directions with the HPLC (CH2H2O: 0.23 ± 0.17 to 0.20 ± 0.10; IHTG%: 0.25 ± 0.20% to 0.22 ± 0.11% compared with the HCLP diet (CH2H2O: 0.34 ± 0.20 vs. 0.38 ± 0.21; IHTG%: 0.38 ± 0.22% vs. 0.43 ± 0.24%, which resulted in a lower IHTG content in the HPLC compared with the HCLP diet group after 12 weeks, which almost reached statistical significance (P = 0.055.A HPLC vs. a HCLP diet has the potential to preserve vs. enlarge IHTG content in healthy non-obese subjects at a constant body weight.Clinicaltrials.gov NCT01551238.

Gamma and electron radiation effects on agricultural by-products with high fibre content

International Nuclear Information System (INIS)

Leonhardt, J.W.; Baer, M.; Nehring, K.

1983-01-01

Gamma and electron radiation effects on wheat straw, oat straw, barley straw, rye straw and dried green fodder are reported. In vitro and in vivo studies show that the digestibility of these agricultural by-products with high fibre content can be increased up to 80% and more at high doses. The increase of the digestibility is connected with a depolymerization of the cellulose and hemicellulose. (author)

Chemical-composition studies of low-temperature-carbonization coal tar

Energy Technology Data Exchange (ETDEWEB)

Edel' shtein, N G; Lanin, V A

1955-01-01

Pintsch-oven low-temperature tar was separated into its constituents by conventional methods, and the average of 2 results was neutral asphaltenes 12.56, basic asphaltenes 2.61, acid asphaltenes 18.82, phenols 13.23, bases 2.31, neutral oil 17.66, crystalline paraffins 7.34, silica-gel tars (I) (benzene extract) 15.40, I (acetone extract) 2.47, carbenes 0.45, and carbides and dust 1.44%. The low-temperature-tar asphaltenes and tars differ from shale-oil tars by being lower in C and higher in H, with a considerably higher C:H ratio. Their specific gravity is somewhat higher, and they are cyclic in structure. The asphaltenes and silica-gel tars of coal tar and shale oil were hydrogenated, molecular weights d/sub 4//sup 20/ and n/sub 4//sup 20/ of the separated compounds were determined, and empirical formulas of the hydrogenated compounds calculated. The neutral oil was separated into saturated, intermediate (iodine number 23), unsaturated (iodine number 51), a small quantity of a mixture of unsaturated and aromatic hydrocarbons, and 44.9% aromatic hydrocarbons. While naphthenes seem to be predominantly present in the neutral-oil fraction of shale oil, aromatic hydrocarbons are predominant in coal oil.

Effect of the rate of heating on the quality of the primary tar in low-temperature coal-carbonization process

Energy Technology Data Exchange (ETDEWEB)

Turskii, Y I

1956-01-01

Two stages are observed. The first stage yields products of the primary and partial decomposition of coal, mainly water, CO/sub 2/, and CO as decomposition products of functional groups (-COOH, > CO, - OH, and so forth). No tar is formed in this stage. The structural decomposition and tar formation occur in the second stage. The rate of heating is important for the quality of the tar obtained. The slow rate of heating with both stages following each other yields a good-quality tar, richer in C and H, with lower O content. In case of high rate of heating both stages overlap. The tar is of poorer quality with higher specific gravity, and contains more O and asphaltenes. The complete experimental data are given in detail.

Reactivity study on thermal cracking of vacuum residues

Science.gov (United States)

León, A. Y.; Díaz, S. D.; Rodríguez, R. C.; Laverde, D.

2016-02-01

This study focused on the process reactivity of thermal cracking of vacuum residues from crude oils mixtures. The thermal cracking experiments were carried out under a nitrogen atmosphere at 120psi between 430 to 500°C for 20 minutes. Temperature conditions were established considering the maximum fractional conversion reported in tests of thermogravimetry performed in the temperature range of 25 to 600°C, with a constant heating rate of 5°C/min and a nitrogen flow rate of 50ml/min. The obtained products were separated in to gases, distillates and coke. The results indicate that the behaviour of thermal reactivity over the chemical composition is most prominent for the vacuum residues with higher content of asphaltenes, aromatics, and resins. Finally some correlations were obtained in order to predict the weight percentage of products from its physical and chemical properties such as CCR, SARA (saturates, aromatics, resins, asphaltenes) and density. The results provide new knowledge of the effect of temperature and the properties of vacuum residues in thermal conversion processes.

Managing hydrogen and molecules in bitumen upgrading : technology and research opportunities

Energy Technology Data Exchange (ETDEWEB)

Gray, M.G. [Alberta Univ., Edmonton, AB (Canada). Dept. of Chemical and Materials Engineering

2006-07-01

An innovative concept in oil sands mining, extraction and upgrading was presented with reference to selectively removing metals. The approach presently used to upgrade bitumen is to drive the properties of slurry mixtures closer to conventional crude oils. However, it is necessary to remove unwanted contaminants and to convert nearly all of the vacuum residues. The yield and value of the final product can be improved by maximizing the hydrogen content of the liquid products. The currently used and proposed upgrading methods are based on technologies developed between 1929 and 1954, including coking, hydrotreating, hydroconversion, and gasification. This study compared the main technologies for upgrading in terms of management of raw materials and hydrogen. The feasibility of improving recovery by using new approaches to separate bitumen was considered. It was concluded that the rejection of large fractions of bitumen as coke or asphaltenes is undesirable. New thermal process face design challenges such as distillation versus cracking coking and fouling. There is much potential for breakthrough in asphaltene precipitation technologies, based on paraffinic froth treatment concepts. tabs., figs.

Di- or polysulphide-bound biomarkers in sulphur-rich geomacromolecules as revealed by selective chemolysis

NARCIS (Netherlands)

Sinninghe Damsté, J.S.; Kohnen, M.E.L.; Kock-van Dalen, A.C.; Leeuw, J.W. de

1991-01-01

Three types of sulphur-rich, high-molecular-weight material in the alkylsulphide, the polar and the asphaltene fracions isolated from the bitumen of an immature bituminous shale from the Vena del Gesso basin (Italy) were desulphurised.

High renewable content sandwich structures based on flax-basalt hybrids and biobased epoxy polymers

Science.gov (United States)

Colomina, S.; Boronat, T.; Fenollar, O.; Sánchez-Nacher, L.; Balart, R.

2014-05-01

In the last years, a growing interest in the development of high environmental efficiency materials has been detected and this situation is more accentuated in the field of polymers and polymer composites. In this work, green composite sandwich structures with high renewable content have been developed with core cork materials. The base resin for composites was a biobased epoxy resin derived from epoxidized vegetable oils. Hybrid basalt-flax fabrics have been used as reinforcements for composites and the influence of the stacking sequence has been evaluated in order to optimize the appropriate laminate structure for the sandwich bases. Core cork materials with different thickness have been used to evaluate performance of sandwich structures thus leading to high renewable content composite sandwich structures. Results show that position of basalt fabrics plays a key role in flexural fracture of sandwich structures due to differences in stiffness between flax and basalt fibers.

Fully Biodegradable Biocomposites with High Chicken Feather Content

Directory of Open Access Journals (Sweden)

Ibon Aranberri

2017-11-01

Full Text Available The aim of this work was to develop new biodegradable polymeric materials with high loadings of chicken feather (CF. In this study, the effect of CF concentration and the type of biodegradable matrix on the physical, mechanical and thermal properties of the biocomposites was investigated. The selected biopolymers were polylactic acid (PLA, polybutyrate adipate terephthalate (PBAT and a PLA/thermoplastic copolyester blend. The studied biocomposites were manufactured with a torque rheometer having a CF content of 50 and 60 wt %. Due to the low tensile strength of CFs, the resulting materials were penalized in terms of mechanical properties. However, high-loading CF biocomposites resulted in lightweight and thermal-insulating materials when compared with neat bioplastics. Additionally, the adhesion between CFs and the PLA matrix was also investigated and a significant improvement of the wettability of the feathers was obtained with the alkali treatment of the CFs and the addition of a plasticizer like polyethylene glycol (PEG. Considering all the properties, these 100% fully biodegradable biocomposites could be adequate for panel components, flooring or building materials as an alternative to wood–plastic composites, contributing to the valorisation of chicken feather waste as a renewable material.

An objective method for High Dynamic Range source content selection

DEFF Research Database (Denmark)

Narwaria, Manish; Mantel, Claire; Da Silva, Matthieu Perreira

2014-01-01

With the aim of improving the immersive experience of the end user, High Dynamic Range (HDR) imaging has been gaining popularity. Therefore, proper validation and performance benchmarking of HDR processing algorithms is a key step towards standardization and commercial deployment. A crucial...... component of such validation studies is the selection of a challenging and balanced set of source (reference) HDR content. In order to facilitate this, we present an objective method based on the premise that a more challenging HDR scene encapsulates higher contrast, and as a result will show up more...

Gravel Mobility in a High Sand Content Riverbed

Science.gov (United States)

Haschenburger, J. K.

2017-12-01

In sand-gravel channels, sand may modify gravel transport by changing conditions of entrainment and promoting longer displacements or gravel may inhibit sand transport if concentrated into distinct deposits, which restrict sand supply with consequences for migrating bedform size or form. This study reports on gravel mobility in the lower San Antonio River, Texas, where gravel content in the bed material ranges from about 1% to more than 20%. Sediment transport observations were collected at three U.S. Geological Survey gauging stations by deploying a Helley-Smith sampler with a 0.2 mm mesh bag from which transport rates and mobile grain sizes were determined. The flow rates sampled translate into an annual exceedance expectation from 0.2% to 98%. Gravel transport rates are generally two orders of magnitude smaller than the rates of sand transport. However, the finest gravels are transported at rates on the same order of magnitude as the coarsest sands. At all sites, the 2 and 2.8 mm fractions are transported at the lowest flow rate sampled, suggesting mobility for at least 38% to as much as 98% of the year. Fractions as large as 8 mm are mobilized at flow rates that are expected between 25% and 53% of the year. The largest fractions captured in the sampling (16 to 32 mm) require flows closer to bankfull conditions that occur no more than 0.8% of the year. Results document that some gravel sizes can be frequently transported in low gradient riverbeds with high sand content.

Formulation and make-up of simulated concentrated water, high ionic content aqueous solution

International Nuclear Information System (INIS)

Gdowski, G.

1997-01-01

This procedure describes the formulation and make-up of Simulated Concentrated Water (SCW), a high-ionic-content water to be used for Activity E-20-50 Long-Term Corrosion Studies. This water has an ionic content which is nominally a factor of a thousand higher than that of representative waters at or near Yucca Mountain. Representative waters were chosen as J-13 well water [Harrar, 1990] and perched water at Yucca Mountain [Glassley, 1996]. J-13 well water is obtained from ground water that is in contact with the Topopah Spring tuff, which is the repository horizon rock. The perched water is located in the Topopah Spring tuff, but below the repository horizon and above the water table. A nominal thousand times higher ionic content was chosen to simulate the water that would result from the wetting of salts which have been previously deposited on a container surface

High-content profiling of cell responsiveness to graded substrates based on combinyatorially variant polymers.

Science.gov (United States)

Liu, Er; Treiser, Matthew D; Patel, Hiral; Sung, Hak-Joon; Roskov, Kristen E; Kohn, Joachim; Becker, Matthew L; Moghe, Prabhas V

2009-08-01

We have developed a novel approach combining high information and high throughput analysis to characterize cell adhesive responses to biomaterial substrates possessing gradients in surface topography. These gradients were fabricated by subjecting thin film blends of tyrosine-derived polycarbonates, i.e. poly(DTE carbonate) and poly(DTO carbonate) to a gradient temperature annealing protocol. Saos-2 cells engineered with a green fluorescent protein (GFP) reporter for farnesylation (GFP-f) were cultured on the gradient substrates to assess the effects of nanoscale surface topology and roughness that arise during the phase separation process on cell attachment and adhesion strength. The high throughput imaging approach allowed us to rapidly identify the "global" and "high content" structure-property relationships between cell adhesion and biomaterial properties such as polymer chemistry and topography. This study found that cell attachment and spreading increased monotonically with DTE content and were significantly elevated at the position with intermediate regions corresponding to the highest "gradient" of surface roughness, while GFP-f farnesylation intensity descriptors were sensitively altered by surface roughness, even in cells with comparable levels of spreading.

Dexterous robotic manipulation of alert adult Drosophila for high-content experimentation.

Science.gov (United States)

Savall, Joan; Ho, Eric Tatt Wei; Huang, Cheng; Maxey, Jessica R; Schnitzer, Mark J

2015-07-01

We present a robot that enables high-content studies of alert adult Drosophila by combining operations including gentle picking; translations and rotations; characterizations of fly phenotypes and behaviors; microdissection; or release. To illustrate, we assessed fly morphology, tracked odor-evoked locomotion, sorted flies by sex, and dissected the cuticle to image neural activity. The robot's tireless capacity for precise manipulations enables a scalable platform for screening flies' complex attributes and behavioral patterns.

Breeding of a new potato variety ‘Nagasaki Kogane’ with high eating quality, high carotenoid content, and resistance to diseases and pests

Science.gov (United States)

Sakamoto, Yu; Mori, Kazuyuki; Matsuo, Yuuki; Mukojima, Nobuhiro; Watanabe, Wataru; Sobaru, Norio; Tamiya, Seiji; Nakao, Takashi; Hayashi, Kazuya; Watanuki, Hitomi; Nara, Kazuhiro; Yamazaki, Kaoru; Chaya, Masataka

2017-01-01

‘Nagasaki Kogane’ is a new potato variety bred from a cross between ‘Saikai 35’ as a female parent and ‘Saikai 33’ as a male. ‘Saikai 35’ is resistant to bacterial wilt, contains the H1 and Rychc genes for resistance to the potato cyst nematode (PCN) and potato virus Y (PVY), respectively, and has high carotenoid content, while ‘Saikai 33’ has large and high-yielding tubers and is resistant to both bacterial wilt and PCN. The carotenoid content of ‘Nagasaki Kogane’ is higher than that of ‘Dejima’, a common double cropping variety. The taste quality of steamed ‘Nagasaki Kogane’ is comparable to that of ‘Inca-no-mezame’ tubers, which has high levels of carotenoid, and superior to ‘Nishiyutaka’, another popular double cropping variety. ‘Nagasaki Kogane’ is suitable for French fries, because its tuber has high starch content. The marketable yield of ‘Nagasaki Kogane’ was higher than that of ‘Inca-no-mezame’ in spring cropping, although it was lower than that of ‘Nishiyutaka’ in double cropping regions. ‘Nagasaki Kogane’ tubers are larger on average than ‘Inca-no-mezame’ tubers in spring cropping. Moreover, the ‘Nagasaki Kogane’ variety is resistant to PCN and PVY, and exhibits a high level of resistance to bacterial wilt. PMID:28744186

Coking of residue hydroprocessing catalysts

Energy Technology Data Exchange (ETDEWEB)

Gray, M.R.; Zhao, Y.X. [Alberta Univ., Edmonton, AB (Canada). Dept. of Chemical Engineering; McKnight, C.A. [Syncrude Canada Ltd., Edmonton, AB (Canada); Komar, D.A.; Carruthers, J.D. [Cytec Industries Inc., Stamford, CT (United States)

1997-11-01

One of the major causes of deactivation of Ni/Mo and Co/Mo sulfide catalysts for hydroprocessing of heavy petroleum and bitumen fractions is coke deposition. The composition and amount of coke deposited on residue hydroprocessing catalysts depends on the composition of the liquid phase of the reactor. In the Athabasca bitumen, the high molecular weight components encourage coke deposition at temperatures of 430 to 440 degrees C and at pressures of 10 to 20 MPa hydrogen pressure. A study was conducted to determine which components in the heavy residual oil fraction were responsible for coking of catalysts. Seven samples of Athabasca vacuum residue were prepared by supercritical fluid extraction with pentane before being placed in the reactor. Carbon content and hydrodesulfurization activity was measured. It was concluded that the deposition of coke depended on the presence of asphaltenes and not on other compositional variables such as content of nitrogen, aromatic carbon or vanadium.

Adaptive platform for fluorescence microscopy-based high-content screening

Science.gov (United States)

Geisbauer, Matthias; Röder, Thorsten; Chen, Yang; Knoll, Alois; Uhl, Rainer

2010-04-01

Fluorescence microscopy has become a widely used tool for the study of medically relevant intra- and intercellular processes. Extracting meaningful information out of a bulk of acquired images is usually performed during a separate post-processing task. Thus capturing raw data results in an unnecessary huge number of images, whereas usually only a few images really show the particular information that is searched for. Here we propose a novel automated high-content microscope system, which enables experiments to be carried out with only a minimum of human interaction. It facilitates a huge speed-increase for cell biology research and its applications compared to the widely performed workflows. Our fluorescence microscopy system can automatically execute application-dependent data processing algorithms during the actual experiment. They are used for image contrast enhancement, cell segmentation and/or cell property evaluation. On-the-fly retrieved information is used to reduce data and concomitantly control the experiment process in real-time. Resulting in a closed loop of perception and action the system can greatly decrease the amount of stored data on one hand and increases the relative valuable data content on the other hand. We demonstrate our approach by addressing the problem of automatically finding cells with a particular combination of labeled receptors and then selectively stimulate them with antagonists or agonists. The results are then compared against the results of traditional, static systems.

High plant uptake of radiocesium from organic soils due to Cs mobility and low soil K content

International Nuclear Information System (INIS)

Sanchez, A.L.; Wright, S.M.; Naylor, C.; Kennedy, V.H.; Dodd, B.A.; Singleton, D.L.; Barnett, C.L.; Stevens, P.A.

1999-01-01

Post-Chernobyl experience has demonstrated that persistently high plant transfer of 137 Cs occurs from organic soils in upland and seminatural ecosystems. The soil properties influencing this transfer have been known for some time but have not been quantified. A pot experiment was conducted using 23 soils collected from selected areas of Great Britain, which were spiked with 134 Cs, and Agrostis capillaris grown for 19--45 days. The plant-to-soil 134 Cs concentration ratio (CR) varied from 0.06 to 44; log CR positively correlated to soil organic matter content (R 2 = 0.84), and CR values were highest for soils with low distribution coefficients (K d ) of 134 Cs. Soils with high organic matter contents and high concentrations of NH 4 + in solution showed high 134 Cs mobility (low K d ). The plant-to-soil solution 134 Cs ratio decreased sharply with increasing soil solution K + . A two parameter linear model, used to predict log CR from soil solution K + and K d , explained 94% of the variability in CR values. In conclusion, the high transfer of 134 Cs in organic soils is related to both the high 134 Cs mobility (low clay content and high NH 4 + concentrations) and low K availability

Method for evaluating building materials with a high content of radioactivity

International Nuclear Information System (INIS)

Stranden, E.

1979-01-01

In order to avoid increased radiation doses to the population due to the introduction of building materials with an unusually high content of radioactivity, a method for evaluating building materials has been developed. An expression for the gamma radiation due to radium, thorium and potassium 40 has been proposed by a Scandinavian group. When this value for a given material does not exceed 1, then no restriction is placed. Should it exceed 1, then the material is subjected to further investigation. Similarly, since the radon concentration depends on the radium content, an expression for this is proposed. Should this be less than unity the material may be sold freely. Should it exceed unity, further investigations must be made. Measurements have also been made on the exhalation of radon from concrete, and the results are given. An expression including this exhalation rate and the ventilation rate, giving the radon concentration is given. (JIW)

High carotenoids content can enhance resistance of selected Pinctada fucata families to high temperature stress.

Science.gov (United States)

Meng, Zihao; Zhang, Bo; Liu, Baosuo; Li, Haimei; Fan, Sigang; Yu, Dahui

2017-02-01

Carotenoids are a class of natural antioxidants widely found in aquatic, and they have significant effects on the growth, survival, and immunity of these organisms. To investigate the mechanisms of carotenoids in high temperature resistance, we observed the immune response of selected pearl oyster Pinctada fucata (Akoya pearl oyster) families with different carotenoids contents to high temperature stress. The results indicated that the survival rate (SR) of P. fucata decreased significantly with increase in temperature from 26 °C to 34 °C and with the decrease of total carotenoids content (TCC); when the TCC was higher, the SR tended to be higher. TCC and total antioxidant capacity (TAC) decreased significantly at 30 °C with increasing stress time. Correlation analysis indicated that TAC was positively and linearly correlated with TCC, and SR was S-type correlated with TCC and TAC. Immune analysis indicated that levels of superoxide dismutase (SOD), catalase (CAT), and malondialdehyde (MDA) in selected families (with higher TCC) under temperature stress (at 30 °C) were generally significantly lower than in the control group (with lowest TCC) and from 0 to 96 h, the levels of each of these substances varied significantly. Levels of SOD, CAT, and MDA within each family first rose from 0 to 3 h, then decreased to their lowest point after 24 h, and then rose again to their highest levels at 96 h. When TCC was higher, the levels of SOD, CAT, and MDA tended to be lower. These findings indicated that carotenoids play an important role in improving survival rates of P. fucata under high temperature stress by enhancing animals' antioxidant system, and could serve as an index for breeding stress-resistant lines in selective breeding practices. Copyright © 2016 Elsevier Ltd. All rights reserved.

Silica removal in industrial effluents with high silica content and low hardness.

Science.gov (United States)

Latour, Isabel; Miranda, Ruben; Blanco, Angeles

2014-01-01

High silica content of de-inked paper mill effluents is limiting their regeneration and reuse after membrane treatments such as reverse osmosis (RO). Silica removal during softening processes is a common treatment; however, the effluent from the paper mill studied has a low hardness content, which makes the addition of magnesium compounds necessary to increase silica removal. Two soluble magnesium compounds (MgCl₂∙6H₂O and MgSO₄∙7H₂O) were tested at five dosages (250-1,500 mg/L) and different initial pH values. High removal rates (80-90%) were obtained with both products at the highest pH tested (11.5). With these removal efficiencies, it is possible to work at high RO recoveries (75-85%) without silica scaling. Although pH regulation significantly increased the conductivity of the waters (at pH 11.5 from 2.1 to 3.7-4.0 mS/cm), this could be partially solved by using Ca(OH)₂ instead of NaOH as pH regulator (final conductivity around 3.0 mS/cm). Maximum chemical oxygen demand (COD) removal obtained with caustic soda was lower than with lime (15 vs. 30%). Additionally, the combined use of a polyaluminum coagulant during the softening process was studied; the coagulant, however, did not significantly improve silica removal, obtaining a maximum increase of only 10%.

Cermet anode compositions with high content alloy phase

Science.gov (United States)

Marschman, Steven C.; Davis, Norman C.

1989-01-01

Cermet electrode compositions comprising NiO-NiFe.sub.2 O.sub.4 -Cu-Ni, and methods for making, are disclosed. Addition of nickel metal prior to formation and densification of a base mixture into the cermet allows for an increase in the total amount of copper and nickel that can be contained in the NiO-NiFe.sub.2 O.sub.4 oxide system. Nickel is present in a base mixture weight concentration of from 0.1% to 10%. Copper is present in the alloy phase in a weight concentration of from 10% to 30% of the densified composition. Such cermet electrodes can be formed to have electrical conductivities well in excess of 100 ohm.sup.-1 cm.sup.-1. Other alloy and oxide system cermets having high content metal phases are also expected to be manufacturable in accordance with the invention.

Diffusion in a pure, high-vacancy-content crystal

International Nuclear Information System (INIS)

McKee, R.A.

1981-01-01

The idea that vacancies can follow a nonrandom walk in a solid has been developed and put into a quantitative form for diffusion in a pure, high-vacancy-content crystal. Intrinsic and tracer diffusion in a metal have been analyzed, and the electrical mobility in an ionic solid has been expressed in terms of the tracer diffusion coefficient and the separate correlation factors for atoms and vacancies. The description uses classical methods of diffusion theory, and generalized results that account for nonrandom vacancy walk have been shown to reduce to those obtained by Howard and Lidiard in a system where the vacancy moves randomly as an isolated point defect. Experimental data for carbon diffusion in fcc iron have been examined to illustrate an interstitial-vacancy analogy that was used in this analysis, and the general result has been applied specifically to discuss vacancy diffusion in Fe/sub 1-x/S

Towards high-siderophore-content foods: optimisation of coprogen production in submerged cultures of Penicillium nalgiovense.

Science.gov (United States)

Emri, Tamás; Tóth, Viktória; Nagy, Csilla Terézia; Nagy, Gábor; Pócsi, Imre; Gyémánt, Gyöngyi; Antal, Károly; Balla, József; Balla, György; Román, Gyula; Kovács, István; Pócsi, István

2013-07-01

Fungal siderophores are likely to possess atheroprotective effects in humans, and therefore studies are needed to develop siderophore-rich food additives or functional foods to increase the siderophore uptake in people prone to cardiovascular diseases. In this study the siderophore contents of mould-ripened cheeses and meat products were analysed and the coprogen production by Penicillium nalgiovense was characterised. High concentrations of hexadentate fungal siderophores were detected in penicillia-ripened Camembert- and Roquefort-type cheeses and also in some sausages. In one sausage fermented by P. nalgiovense, the siderophore content was comparable to those found in cheeses. Penicillium nalgiovense produced high concentrations of coprogen in submerged cultures, which were affected predominantly by the available carbon and nitrogen sources under iron starvation. Considerable coprogen yields were still detectable in the presence of iron when the fermentation medium was supplemented with the iron chelator Na₂-EDTA or when P. nalgiovense was co-cultivated with Saccharomyces cerevisiae. These data may be exploitable in the future development of high-siderophore-content foods and/or food additives. Nevertheless, the use of P. nalgiovense fermentation broths for these purposes may be limited by the instability of coprogen in fermentation media and by the β-lactam production by the fungus. © 2012 Society of Chemical Industry.

Ultrasonic characterization of coal liquefaction products. Final report, April 11, 1979-February 11, 1980

Energy Technology Data Exchange (ETDEWEB)

Leffert, C. B.; Weisman, L.; Moore, D.

1980-02-29

The Wayne State University ultrasonic device and technique was used successfully to calibrate coal-derived 0 to 45% wt % asphaltene-in-oil mixtures (2 wt % increments) for transmitted signal strength versus temperature (25 to 100/sup 0/C). Computer-aided cross plots of the transmitted signal strength versus concentration of asphaltene showed that a wide range of concentration and temperature exists where the viscosity-dominated (lower temperature) sound absorption is such that a single-valued number for the concentration of the asphaltene can be obtained from measurement of the sample temperature and transmitted signal strength and thus obtain a measure of the quality of the coal-derived product. Sufficient samples were not provided to obtain a complete calibration of added particulate matter of ash and undissolved coal at all asphaltene in oil concentrations; however, calibrations were made of added ash to three concentrations of asphaltene-in-oil and the data showed the greatest effect at the higher temperatures indicating (as planned) that sound attenuation from Rayleigh scattering is predominant with the suspended particles. We conclude from these two sets of measurements that there is a excellent expectation that the Wayne State ultrasonic device and technique could be used to simultaneously measure (on-line) the suspended particle concentration as well as the quality of the coal-derived product.

Depth-resolved incoherent and coherent wide-field high-content imaging (Conference Presentation)

Science.gov (United States)

So, Peter T.

2016-03-01

Recent advances in depth-resolved wide-field imaging technique has enabled many high throughput applications in biology and medicine. Depth resolved imaging of incoherent signals can be readily accomplished with structured light illumination or nonlinear temporal focusing. The integration of these high throughput systems with novel spectroscopic resolving elements further enable high-content information extraction. We will introduce a novel near common-path interferometer and demonstrate its uses in toxicology and cancer biology applications. The extension of incoherent depth-resolved wide-field imaging to coherent modality is non-trivial. Here, we will cover recent advances in wide-field 3D resolved mapping of refractive index, absorbance, and vibronic components in biological specimens.

Comparative genome analysis to identify SNPs associated with high oleic acid and elevated protein content in soybean.

Science.gov (United States)

Kulkarni, Krishnanand P; Patil, Gunvant; Valliyodan, Babu; Vuong, Tri D; Shannon, J Grover; Nguyen, Henry T; Lee, Jeong-Dong

2018-03-01

The objective of this study was to determine the genetic relationship between the oleic acid and protein content. The genotypes having high oleic acid and elevated protein (HOEP) content were crossed with five elite lines having normal oleic acid and average protein (NOAP) content. The selected accessions were grown at six environments in three different locations and phenotyped for protein, oil, and fatty acid components. The mean protein content of parents, HOEP, and NOAP lines was 34.6%, 38%, and 34.9%, respectively. The oleic acid concentration of parents, HOEP, and NOAP lines was 21.7%, 80.5%, and 20.8%, respectively. The HOEP plants carried both FAD2-1A (S117N) and FAD2-1B (P137R) mutant alleles contributing to the high oleic acid phenotype. Comparative genome analysis using whole-genome resequencing data identified six genes having single nucleotide polymorphism (SNP) significantly associated with the traits analyzed. A single SNP in the putative gene Glyma.10G275800 was associated with the elevated protein content, and palmitic, oleic, and linoleic acids. The genes from the marker intervals of previously identified QTL did not carry SNPs associated with protein content and fatty acid composition in the lines used in this study, indicating that all the genes except Glyma.10G278000 may be the new genes associated with the respective traits.

Effect of alkali metal content of carbon on retention of iodine at high temperatures

International Nuclear Information System (INIS)

Evans, A.G.

1975-01-01

Activated carbon for filters in reactor confinement systems is intentionally impregnated with iodine salts to enhance the removal of radioiodine from air streams containing organic iodides. When a variety of commercial impregnated carbons were evaluated for iodine retention at elevated temperatures (4 hours at 180 0 C), wide variations in iodine penetration were observed. The alkali metal and iodine content of carbon samples was determined by neutron activation analysis, and a strong correlation was shown between the atom ratio of iodine to alkali metals in the carbons and the high-temperature retention performance. Carbons containing excess alkali (especially potassium) have iodine penetration values 10 to 100 times lower than carbons containing excess iodine. Both low I/K ratios and high pH values were shown essential to high efficiency iodine retention; therefore, conversion of elemental iodine to ionic iodine is the basic reaction mechanism. The natural high K + content and high pH coconut carbons make coconut the preferred natural base material for nuclear air cleaning applications. Studies show, however, that treatment of low potassium carbons with a mixture of KOH and I 2 may produce a product equal to or better than I 2 -impregnated coconut carbons at a lower cost. (U.S.)

Frying stability of high oleic sunflower oils as affected by composition of tocopherol isomers and linoleic acid content.

Science.gov (United States)

Aladedunye, Felix; Przybylski, Roman

2013-12-01

The influence of linoleic acid content and tocopherol isomeric composition on the frying performance of high oleic sunflower oil was evaluated during a 14-day restaurant style frying operation. At equal linoleic acid content, no significant difference was observed between high oleic sunflower oil containing only α-tocopherol and the sample containing a mixture of α-, γ-, and δ-isomers as measured by the amount of total polar components, oligomers, anisidine value, and free fatty acids. On the contrary, at similar tocopherol isomeric composition, high oleic sunflower oil containing lower amount of linoleic acid showed superior frying stability compared to the sample with a higher content of linoleic acid, suggesting that the frying performance of high oleic sunflower oil is dictated primarily by the level of linoleic acid, with the tocopherol isomeric composition of the oil having no significant influence. In all oil samples, the loss of γ-tocopherol was higher than the corresponding loss of α-tocopherol. Copyright © 2013 Elsevier Ltd. All rights reserved.

Retrogradation of Maize Starch after High Hydrostatic Pressure Gelation: Effect of Amylose Content and Depressurization Rate

KAUST Repository

Yang, Zhi; Swedlund, Peter; Gu, Qinfen; Hemar, Yacine; Chaieb, Saharoui

2016-01-01

High hydrostatic pressure (HHP) has been employed to gelatinize or physically modify starch dispersions. In this study, waxy maize starch, normal maize starch, and two high amylose content starch were processed by a HHP of the order of 600 MPa

Submerged Cultivation of Mycelium with High Ergothioneine Content from the Culinary-Medicinal Golden Oyster Mushroom, Pleurotus citrinopileatus (Higher Basidiomycetes).

Science.gov (United States)

Lin, Shin-Yi; Chien, Shih-Chang; Wang, Sheng-Yang; Mau, Jeng-Leun

2015-01-01

The optimization of submerged culture of the culinary-medicinal golden oyster mushroom, Pleurotus citrinopileatus, was studied using a one-factor-at-a-time, two-stage stimulation and central composite rotatable design to produce mycelia with high ergothioneine content. The optimal culture conditions for mycelia harvested at day 22 were a temperature of 25°C, an inoculation ratio of 5%, 2% glucose, 0.5% yeast extract, and adjustment of the initial pH value to 10. The biomass and ergothioneine content were 8.28 g/L and 10.65 mg/g dry weight (dw), respectively. The addition of an amino acid precursor increased the ergothioneine content of mycelia; cysteine was the most effective. In addition, the results obtained from central composite rotatable design showed that the recommended combination for cysteine, histidine, and methionine was 8, 4, and 0.5 mmol/L, respectively. The predicted ergothioneine content was 13.90 mg/g dw, whereas the experimental maximal ergothioneine content was 14.57 mg/g dw. With the addition of complex precursors and under optimal culture conditions, mycelia harvested at days 16-20 had higher ergothioneine content. Accordingly, the information obtained could be used to produce mycelia with high ergothioneine content.

Retrogradation of Maize Starch after High Hydrostatic Pressure Gelation: Effect of Amylose Content and Depressurization Rate

KAUST Repository

Yang, Zhi

2016-05-24

High hydrostatic pressure (HHP) has been employed to gelatinize or physically modify starch dispersions. In this study, waxy maize starch, normal maize starch, and two high amylose content starch were processed by a HHP of the order of 600 MPa, at 25°C for 15min. The effect of HHP processing on the crystallization of maize starches with various amylose content during storage at 4°C was investigated. Crystallization kinetics of HHP treated starch gels were investigated using rheology and FTIR. The effect of crystallization on the mechanical properties of starch gel network were evaluated in terms of dynamic complex modulus (G*). The crystallization induced increase of short-range helices structures were investigated using FTIR. The pressure releasing rate does not affect the starch retrogradation behaviour. The rate and extent of retrogradation depends on the amylose content of amylose starch. The least retrogradation was observed in HHP treated waxy maize starch. The rate of retrogradation is higher for HHP treated high amylose maize starch than that of normal maize starch. A linear relationship between the extent of retrogradation (phase distribution) measured by FTIR and G* is proposed.

Retrogradation of Maize Starch after High Hydrostatic Pressure Gelation: Effect of Amylose Content and Depressurization Rate

Science.gov (United States)

Yang, Zhi; Swedlund, Peter; Gu, Qinfen; Hemar, Yacine; Chaieb, Sahraoui

2016-01-01

High hydrostatic pressure (HHP) has been employed to gelatinize or physically modify starch dispersions. In this study, waxy maize starch, normal maize starch, and two high amylose content starch were processed by a HHP of the order of 600 MPa, at 25°C for 15min. The effect of HHP processing on the crystallization of maize starches with various amylose content during storage at 4°C was investigated. Crystallization kinetics of HHP treated starch gels were investigated using rheology and FTIR. The effect of crystallization on the mechanical properties of starch gel network were evaluated in terms of dynamic complex modulus (G*). The crystallization induced increase of short-range helices structures were investigated using FTIR. The pressure releasing rate does not affect the starch retrogradation behaviour. The rate and extent of retrogradation depends on the amylose content of amylose starch. The least retrogradation was observed in HHP treated waxy maize starch. The rate of retrogradation is higher for HHP treated high amylose maize starch than that of normal maize starch. A linear relationship between the extent of retrogradation (phase distribution) measured by FTIR and G* is proposed. PMID:27219066

Retrogradation of Maize Starch after High Hydrostatic Pressure Gelation: Effect of Amylose Content and Depressurization Rate.

Directory of Open Access Journals (Sweden)

Zhi Yang

Full Text Available High hydrostatic pressure (HHP has been employed to gelatinize or physically modify starch dispersions. In this study, waxy maize starch, normal maize starch, and two high amylose content starch were processed by a HHP of the order of 600 MPa, at 25°C for 15min. The effect of HHP processing on the crystallization of maize starches with various amylose content during storage at 4°C was investigated. Crystallization kinetics of HHP treated starch gels were investigated using rheology and FTIR. The effect of crystallization on the mechanical properties of starch gel network were evaluated in terms of dynamic complex modulus (G*. The crystallization induced increase of short-range helices structures were investigated using FTIR. The pressure releasing rate does not affect the starch retrogradation behaviour. The rate and extent of retrogradation depends on the amylose content of amylose starch. The least retrogradation was observed in HHP treated waxy maize starch. The rate of retrogradation is higher for HHP treated high amylose maize starch than that of normal maize starch. A linear relationship between the extent of retrogradation (phase distribution measured by FTIR and G* is proposed.

Investigated Miscible CO2 Flooding for Enhancing Oil Recovery in Wettability Altered Chalk and Sandstone Rocks

Energy Technology Data Exchange (ETDEWEB)

Tabrizy, Vahid Alipour

2012-07-01

The thesis addresses oil recovery by miscible CO2 flooding from modified sandstone and chalk rocks. Calcite mineral surface is modified with stearic acid (SA) and asphaltene, and the silicate mineral surfaces are modified with N,N-dimethyldodecylamine (NN-DMDA) and asphaltene. The stability of adsorbed polar components in presence of SO4 2- and Mg2 + ions is also investigated. Recovery from sandstone cores is consistently lower than that from chalk cores saturated with the same oil and flooded with CO2 at all miscible flooding conditions. This may be due to the larger permeability contrasts in sandstone cores, which promote the fingering phenomenon. Miscible CO2 flooding for chalk and sandstone cores with distilled water, as initial water saturation, shows also lower oil recovery than cores saturated with different ions. At higher miscible flooding conditions, higher oil recovery is obtained. However, presence of light components (such as C1 or C3) in oil reduced the recovery. Oil recovery in presence of methane (C1) is lower than that in presence of methane and propane (C1/C3). A ternary diagram was constructed in order to understand the CO2 flooding mechanism(s) at the different flooding conditions and in presence of light components. The side effect of the flooding with CO2 is the probability for asphaltene deposition. An approach based on solubility parameter in the liquid, is used to assess the risk for asphaltene deposition during CO2 miscible flooding. The light components (C1/C3) and higher flooding conditions enhanced the risk for asphaltene instability. It is also shown higher amount of asphaltene deposition in chalk cores than that in sandstone cores at similar miscibility conditions.(au)

Mutational breeding and genetic engineering in the development of high grain protein content.

Science.gov (United States)

Wenefrida, Ida; Utomo, Herry S; Linscombe, Steve D

2013-12-04

Cereals are the most important crops in the world for both human consumption and animal feed. Improving their nutritional values, such as high protein content, will have significant implications, from establishing healthy lifestyles to helping remediate malnutrition problems worldwide. Besides providing a source of carbohydrate, grain is also a natural source of dietary fiber, vitamins, minerals, specific oils, and other disease-fighting phytocompounds. Even though cereal grains contain relatively little protein compared to legume seeds, they provide protein for the nutrition of humans and livestock that is about 3 times that of legumes. Most cereal seeds lack a few essential amino acids; therefore, they have imbalanced amino acid profiles. Lysine (Lys), threonine (Thr), methionine (Met), and tryptophan (Trp) are among the most critical and are a limiting factor in many grain crops for human nutrition. Tremendous research has been put into the efforts to improve these essential amino acids. Development of high protein content can be outlined in four different approaches through manipulating seed protein bodies, modulating certain biosynthetic pathways to overproduce essential and limiting amino acids, increasing nitrogen relocation to the grain through the introduction of transgenes, and exploiting new genetic variance. Various technologies have been employed to improve protein content including conventional and mutational breeding, genetic engineering, marker-assisted selection, and genomic analysis. Each approach involves a combination of these technologies. Advancements in nutrigenomics and nutrigenetics continue to improve public knowledge at a rapid pace on the importance of specific aspects of food nutrition for optimum fitness and health. An understanding of the molecular basis for human health and genetic predisposition to certain diseases through human genomes enables individuals to personalize their nutritional requirements. It is critically important

Enhancement of lipid accumulation by oleaginous yeast through phosphorus limitation under high content of ammonia.

Science.gov (United States)

Huang, Xiangfeng; Luo, Huijuan; Mu, Tianshuai; Shen, Yi; Yuan, Ming; Liu, Jia

2018-04-18

Low concentrations of acetic acid were used as carbon source to cultivate Cryptococcus curvatus MUCL 29819 for lipid production under high content of ammonia. Phosphorus limitation combined with initial pH regulation (pH = 6) weakened inhibition of free ammonia and promoted lipid accumulation. In batch cultivation, the produced lipid content and yield was 30.3% and 0.92 g/L, higher than those under unlimited condition (18.3% and 0.64 g/L). The content of monounsaturated fatty acid also increased from 37.3% (unlimited condition) to 45.8% (phosphorus-limited condition). During sequencing batch cultivation (SBC), the lipid content reached up to 51.02% under phosphorus-limited condition while only 31.88% under unlimited condition, which can be explained by the higher conversion efficiency of the carbon source to lipid. The total energy consumption including lipid extraction, transesterification and purification was 7.47 and 8.33 GJ under phosphorus-limited and unlimited condition, respectively. Copyright © 2018. Published by Elsevier Ltd.

Correlation between the mechanical property and microstructure of porcelain with high alumina contents

International Nuclear Information System (INIS)

Goulart, E.P.; Jordao, M.A.P.; Souza, D.D.D. de; Kiyohara, P.K.

1989-01-01

The substitution of quartz by a alumina in porcelain bodies produces high increase in mechanical strenght of the fired body. In the present paper, body microstruture variations caused by gradual quartz by alumina substitution have been studied and correlated to physical characteristics variations. Several bodies with quartz content varying from 22% to 0% and accordingly, the alumina content varying from 0% to 22% have been prepared. Other quartz-free bodies and the alumina content going up to 40% have been prepared. Three different alumina types have been used: two of them were of microcrystal type, the original crystal size between 1-5μm and obtained by calcining aluminum hydroxide from Bayer process; the third one is an originally macrocrystal type alumina obtained by grinding electrofused material. The sintering temperature ranged from 1250 0 C to 1400 0 C with 50 0 C of intervals between each firing. Tests on specimens covered flexural strenght, water absortion, apparent density and porosity. Microstruture variations and new mineral formation was continuously detected by scanning electron microscopy and X-ray diffraction [pt

Design and Implementation of High Performance Content-Addressable Memories.

Science.gov (United States)

1985-12-01

content addressability and two basic implementations of content addressing. The need and application of hardware CAM is presented to motivate the " topic...3r Pass 4th Ps4 Pass Figure 2.15 Maximum SearchUsing All-Parallel CAM - left-most position (the most significant bit) and the other IF bits are zeros

Can the water content of highly compacted bentonite be increased by applying a high water pressure?

International Nuclear Information System (INIS)

Pusch, R.; Kasbohm, J.

2001-10-01

A great many laboratory investigations have shown that the water uptake in highly compacted MX-80 clay takes place by diffusion at low external pressure. It means that wetting of the clay buffer in the deposition holes of a KBS-3 repository is very slow if the water pressure is low and that complete water saturation can take several tens of years if the initial degree of water saturation of the buffer clay and the ability of the rock to give off water are low. It has therefore been asked whether injection of water can raise the degree of water saturation and if a high water pressure in the nearfield can have the same effect. The present report describes attempts to moisten highly compacted blocks of MX-80 clay with a dry density of 1510 kg/m 3 by injecting water under a pressure of 650 kPa through a perforated injection pipe for 3 and 20 minutes, respectively. The interpretation was made by determining the water content of a number of samples located at different distances from the pipe. An attempt to interpret the pattern of distribution of injected uranium acetate solution showed that the channels into which the solution went became closed in a few minutes and that dispersion in the homogenized clay gave low U-concentrations. The result was that the water content increased from about 9 to about 11-12 % within a distance of about 1 centimeter from the injection pipe and to slightly more than 9 % at a distance of about 4-5 cm almost independently of the injection time. Complete water saturation corresponds to a water content of about 30 % and the wetting effect was hence small from a practical point of view. By use of microstructural models it can be shown that injected water enters only the widest channels that remain after the compaction and that these channels are quickly closed by expansion of the hydrating surrounding clay. Part of the particles that are thereby released become transported by the flowing water and cause clogging of the channels, which is

[Analysis of nursing-related content portrayed in middle and high school textbooks under the national common basic curriculum in Korea].

Science.gov (United States)

Jung, Myun Sook; Choi, Hyeong Wook; Li, Dong Mei

2010-02-01

The purpose of this study was to analyze nursing-related content in middle, and high school textbooks under the National Common Basic Curriculum in Korea. Nursing-related content from 43 middle school textbooks and 13 high school textbooks was analyzed. There were 28 items of nursing-related content in the selected textbooks. Among them, 13 items were in the 'nursing activity' area, 6 items were in the 'nurse as an occupation' area, 2 items were in the 'major and career choice' area, 6 items were 'just one word' and 1 item in 'others'. The main nursing related content which portrayed in the middle and high school textbooks were caring for patients (7 items accounting for 46.5%), nurses working in hospitals (6 items accounting for 21.4%). In terms of gender perspective, female nurses (15 items accounting for 53.6%) were most prevalent.

Alternate-Day High-Fat Diet Induces an Increase in Mitochondrial Enzyme Activities and Protein Content in Rat Skeletal Muscle.

Science.gov (United States)

Li, Xi; Higashida, Kazuhiko; Kawamura, Takuji; Higuchi, Mitsuru

2016-04-06

Long-term high-fat diet increases muscle mitochondrial enzyme activity and endurance performance. However, excessive calorie intake causes intra-abdominal fat accumulation and metabolic syndrome. The purpose of this study was to investigate the effect of an alternating day high-fat diet on muscle mitochondrial enzyme activities, protein content, and intra-abdominal fat mass in rats. Male Wistar rats were given a standard chow diet (CON), high-fat diet (HFD), or alternate-day high-fat diet (ALT) for 4 weeks. Rats in the ALT group were fed a high-fat diet and standard chow every other day for 4 weeks. After the dietary intervention, mitochondrial enzyme activities and protein content in skeletal muscle were measured. Although body weight did not differ among groups, the epididymal fat mass in the HFD group was higher than those of the CON and ALT groups. Citrate synthase and beta-hydroxyacyl CoA dehydrogenase activities in the plantaris muscle of rats in HFD and ALT were significantly higher than that in CON rats, whereas there was no difference between HFD and ALT groups. No significant difference was observed in muscle glycogen concentration or glucose transporter-4 protein content among the three groups. These results suggest that an alternate-day high-fat diet induces increases in mitochondrial enzyme activities and protein content in rat skeletal muscle without intra-abdominal fat accumulation.

OMASAL MORPHOLOGY OF DAIRY COWS FED WITH HIGH OR LOW GRAIN CONTENT DIET PRIOR PARTURITION

Directory of Open Access Journals (Sweden)

Danilo de Oliveira Rocha Bhering Santoro

2015-12-01

Full Text Available ABSTRACT Little is known about the morphological response of the omasum in dairy cows that consume a high-energy diet pre-partum. The aim of this study was to investigate whether a transitional diet with high grain content is able to induce changes in omasum morphology. Six weeks before the expected calving, four Holstein cows were fed a standardization diet, and four weeks before delivery, the cows were fed a diet with high grain content (HGC or low (LGC grain content. After calving, all of the cows were fed a high energy lactation diet. The cows that were fed the HGC diet pre-partum had higher dry matter and nutrient intake than the cows that were fed the LGC diet. The mitotic index of the omasum epithelium was higher than the mitotic index in the rumen, but apparently the response to the diet stimuli was slower. In the cows that were fed the HGC diet, the omasum papillae were taller one week before parturition and two weeks post-partum. Cows that were fed the HGC diet had a thinner epithelium due to thinner non-keratinized layers of the omasum epithelium. We conclude that the omasum mucosa of dairy cows responds to the stimuli of a pre-partum HGC diet, which was indicated by the greater height of the omasum papillae and by the reduced thickness of the omasum epithelium. It seems that the mitotic index responds a little more slowly, but the response to the diet stimuli is stronger in the omasum epithelium than in the rumen.

Hydroprocessing catalysts utilization and regeneration schemes

Energy Technology Data Exchange (ETDEWEB)

Furimsky, E.

The catalyst reactor inventory represents an important part of the cost of hydroprocessing operation. The selection of a suitable catalyst and reactor is influenced by feedstock properties. Processes ensuring an uninterrupted operation during catalyst addition and withdrawal are preferred for processing high asphaltene and metal content feedstocks. The spent catalyst can be regenerated and returned to the operation if the extent of its deactivation is not high. The regeneration may be performed either in-situ or off-site. The former is suitable for fixed bed reactors whereas the catalyst from ebullated bed reactors must be regenerated off-site. The regeneration of spent catalysts heavily loaded with metals such as V, Ni and Fe may not be economic. Such catalysts may be suitable for metal reclamation. An environmentally safe method for catalyst disposal must be found if neither regeneration nor metal reclamation from spent catalysts can be performed.

Radon exhalation rate and natural radionuclide content in building materials of high background areas of Ramsar, Iran.

Science.gov (United States)

Bavarnegin, E; Fathabadi, N; Vahabi Moghaddam, M; Vasheghani Farahani, M; Moradi, M; Babakhni, A

2013-03-01

Radon exhalation rates from building materials used in high background radiation areas (HBRA) of Ramsar were measured using an active radon gas analyzer with an emanation container. Radon exhalation rates from these samples varied from below the lower detection limit up to 384 Bq.m(-2) h(-1). The (226)Ra, (232)Th and (40)K contents were also measured using a high resolution HPGe gamma- ray spectrometer system. The activity concentration of (226)Ra, (232)Th and (40)K content varied from below the minimum detection limit up to 86,400 Bq kg(-1), 187 Bq kg(-1) and 1350 Bq kg(-1), respectively. The linear correlation coefficient between radon exhalation rate and radium concentration was 0.90. The result of this survey shows that radon exhalation rate and radium content in some local stones used as basements are extremely high and these samples are main sources of indoor radon emanation as well as external gamma radiation from uranium series. Copyright © 2012 Elsevier Ltd. All rights reserved.

Glassy slags as novel waste forms for remediating mixed wastes with high metal contents

International Nuclear Information System (INIS)

Feng, X.; Wronkiewicz, D.J.; Bates, J.K.; Brown, N.R.; Buck, E.C.; Gong, M.; Ebert, W.L.

1994-01-01

Argonne National Laboratory (ANL) is developing a glassy slag final waste form for the remediation of low-level radioactive and mixed wastes with high metal contents. This waste form is composed of various crystalline and metal oxide phases embedded in a silicate glass phase. This work indicates that glassy slag shows promise as final waste form because (1) it has similar or better chemical durability than high-level nuclear waste (HLW) glasses, (2) it can incorporate large amounts of metal wastes, (3) it can incorporate waste streams having low contents of flux components (boron and alkalis), (4) it has less stringent processing requirements (e.g., viscosity and electric conductivity) than glass waste forms, (5) its production can require little or no purchased additives, which can result in greater reduction in waste volume and overall treatment costs. By using glassy slag waste forms, minimum additive waste stabilization approach can be applied to a much wider range of waste streams than those amenable only to glass waste forms

Evaluation of bio-materials’ rejuvenating effect on binders for high-reclaimed asphalt content mixtures

Directory of Open Access Journals (Sweden)

A. Jiménez del Barco-Carrión

2017-07-01

Full Text Available The interest in using bio-materials in pavement engineering has grown significantly over the last decades due to environmental concerns about the use of non-recoverable natural resources. In this paper, bio-materials are used together with Reclaimed Asphalt (RA to restore some of the properties of the aged bitumen present in mixtures with high RA content. For this purpose, two bio-materials are studied and compared to conventional and polymer modified bitumens. Blends of these materials with RA bitumen were produced and studied to simulate a 50% RA mixture. The rejuvenating effect of the two bio-materials on RA has been assessed and compared with the effect of the conventional binders. Apparent Molecular Weight Distribution of the samples (obtained by the ?-method and different rheological parameters were used for this purpose. Results revealed the power of bio-materials to rejuvenate RA bitumen, showing their capability to be used as fresh binders in high-RA content mixtures.

Evaluation of bio-materials’ rejuvenating effect on binders for high-reclaimed asphalt content mixtures

International Nuclear Information System (INIS)

Jiménez del Barco-Carrión, A.; Pérez-Martínez, M.; Themeli, A.; Lo Presti, D.; Marsac, P.; Pouget, S.; Hammoum, F.; Chailleux, E.; Airey, G.D.

2017-01-01

The interest in using bio-materials in pavement engineering has grown significantly over the last decades due to environmental concerns about the use of non-recoverable natural resources. In this paper, bio-materials are used together with Reclaimed Asphalt (RA) to restore some of the properties of the aged bitumen present in mixtures with high RA content. For this purpose, two bio-materials are studied and compared to conventional and polymer modified bitumens. Blends of these materials with RA bitumen were produced and studied to simulate a 50% RA mixture. The rejuvenating effect of the two bio-materials on RA has been assessed and compared with the effect of the conventional binders. Apparent Molecular Weight Distribution of the samples (obtained by the ?-method) and different rheological parameters were used for this purpose. Results revealed the power of bio-materials to rejuvenate RA bitumen, showing their capability to be used as fresh binders in high-RA content mixtures. [es

[Low caloric value and high salt content in the meals served in school canteens].

Science.gov (United States)

Paiva, Isabel; Pinto, Carlos; Queirós, Laurinda; Meister, Maria Cristina; Saraiva, Margarida; Bruno, Paula; Antunes, Delfina; Afonso, Manuel

2011-01-01

School lunch can contribute to aggravate food quality, by excess or deficiency, or it can contribute to compensate and alleviate them. This school meal should be an answer to combating the epidemic of obesity, and to feed some grace children. The objective was to study the nutritional composition of catering in canteens of public schools, from Northern municipalities in the District of Porto: Vila do Conde, Póvoa de Varzim, Santo Tirso and Trofa. Meals were subjected to laboratory analysis. Thirty two meals, four per each school were analysed, reference values for the analysis of the nutritional composition of meals were dietary reference intakes (USA) and eating well at school (UK). The average energy meal content was 447 kcal and the median 440 kcal (22% of daily calories). The average values of nutrients, per meal, were: lipids 9, 8 g, carbohydrate 65,7 g and proteins 24,0 g. In average the contribution for the meal energy was: 20% fat, 59% carbohydrate and 21% protein. In more than 75% of meals the contribution of lipid content was below the lower bound of the reference range. The average content of sodium chloride per meal was 3.4 g, and the confidence interval 95% to average 3.0 to 3.8 g, well above the recommended maximum value of 1.5 grams. The average content fiber per meal was 10.8 g higher than the minimum considered appropriate. In conclusion, the value low caloric meals was mainly due to the low fat content, and content salt of any of the components of the meal was very high.

Chemical segregation of progeny of camphor trees with high camphor c.q. Linalool content

NARCIS (Netherlands)

Khien, P.V.; Chien, Ho Trung; Dung, N.X.; Leclercq, A.X.; Leclercq, P.A.

1998-01-01

The propagation of open pollinated seed from two camphor trees with a high camphor and linalool content, respectively, yielded 115 progeny. The chemical composition of the leaf oils of these trees was analyzed by a combination of capillary GC and GC/MS. Four chemotypes could be distinguished among

The Role of Content Knowledge in Ill-Structured Problem Solving for High School Physics Students

Science.gov (United States)

Milbourne, Jeff; Wiebe, Eric

2018-02-01

While Physics Education Research has a rich tradition of problem-solving scholarship, most of the work has focused on more traditional, well-defined problems. Less work has been done with ill-structured problems, problems that are better aligned with the engineering and design-based scenarios promoted by the Next Generation Science Standards. This study explored the relationship between physics content knowledge and ill-structured problem solving for two groups of high school students with different levels of content knowledge. Both groups of students completed an ill-structured problem set, using a talk-aloud procedure to narrate their thought process as they worked. Analysis of the data focused on identifying students' solution pathways, as well as the obstacles that prevented them from reaching "reasonable" solutions. Students with more content knowledge were more successful reaching reasonable solutions for each of the problems, experiencing fewer obstacles. These students also employed a greater variety of solution pathways than those with less content knowledge. Results suggest that a student's solution pathway choice may depend on how she perceives the problem.

Identifying Content Knowledge for Teaching Energy: Examples from High School Physics

Science.gov (United States)

Robertson, Amy D.; Scherr, Rachel E.; Goodhew, Lisa M.; Daane, Abigail R.; Gray, Kara E.; Aker, Leanna B.

2017-01-01

"Content knowledge for teaching" is the specialized content knowledge that teachers use in practice the content knowledge that serves them for tasks of teaching such as revoicing students' ideas, choosing an instructional activity to address a student misunderstanding, and evaluating student statements. We describe a methodology for…

Effect of High Intensity Ultrasound and Pasteurization on Anthocyanin Content in Strawberry Juice

Directory of Open Access Journals (Sweden)

Igor Dubrović

2011-01-01

Full Text Available The purpose of this investigation is to study the influence of high intensity ultrasound and pasteurization on the stability of anthocyanins and their content in strawberry juice. Different ultrasound process parameters for the treatment of juices are compared to the classical thermal treatments. For ultrasound treatments, three parameters were varied according to the statistical experimental design. Central composite design was used to optimize and design experimental parameters: temperature (25, 40 and 55 °C, amplitude (60, 90 and 120 μm and time (3, 6, and 9 min. It was found that the anthocyanin content after pasteurization (85 °C for 2 min was reduced by 5.3 to 5.8 % compared to untreated juices. After treatment with ultrasound (20 °C for 3, 6 or 9 min or thermosonication (40 °C for 3, 6 or 9 min and 60 °C for 3 or 6 min, the degradation of anthocyanins was generally less intensive and was 0.7–4.4 % compared to the untreated juices. Only in the case of ultrasonic treatment at a temperature of 55 °C and treatment time of 9 min the total content of anthocyanins, compared to untreated juice, was reduced by 5.8 to 7.1 %, and their degradation was greater than that of pasteurized juices. From the results it can be concluded that total anthocyanin content was greater in more than 85 % of the selected ultrasound treatments compared to pasteurized juices. Ultrasound treatment can replace pasteurization in terms of preserving total anthocyanin content. The modelling approaches using response surface methodology (RSM developed in this study exploit data in order to identify the optimal processing parameters for lowering degradation of anthocyanins in strawberry juice during ultrasound processing.

High water content in primitive continental flood basalts.

Science.gov (United States)

Xia, Qun-Ke; Bi, Yao; Li, Pei; Tian, Wei; Wei, Xun; Chen, Han-Lin

2016-05-04

As the main constituent of large igneous provinces, the generation of continental flood basalts (CFB) that are characterized by huge eruption volume (>10(5) km(3)) within short time span (primitive CFB in the early Permian Tarim large igneous province (NW China), using the H2O content of ten early-formed clinopyroxene (cpx) crystals that recorded the composition of the primitive Tarim basaltic melts and the partition coefficient of H2O between cpx and basaltic melt. The arc-like H2O content (4.82 ± 1.00 wt.%) provides the first clear evidence that H2O plays an important role in the generation of CFB.

High-content, high-throughput screening for the identification of cytotoxic compounds based on cell morphology and cell proliferation markers.

Directory of Open Access Journals (Sweden)

Heather L Martin

Full Text Available Toxicity is a major cause of failure in drug discovery and development, and whilst robust toxicological testing occurs, efficiency could be improved if compounds with cytotoxic characteristics were identified during primary compound screening. The use of high-content imaging in primary screening is becoming more widespread, and by utilising phenotypic approaches it should be possible to incorporate cytotoxicity counter-screens into primary screens. Here we present a novel phenotypic assay that can be used as a counter-screen to identify compounds with adverse cellular effects. This assay has been developed using U2OS cells, the PerkinElmer Operetta high-content/high-throughput imaging system and Columbus image analysis software. In Columbus, algorithms were devised to identify changes in nuclear morphology, cell shape and proliferation using DAPI, TOTO-3 and phosphohistone H3 staining, respectively. The algorithms were developed and tested on cells treated with doxorubicin, taxol and nocodazole. The assay was then used to screen a novel, chemical library, rich in natural product-like molecules of over 300 compounds, 13.6% of which were identified as having adverse cellular effects. This assay provides a relatively cheap and rapid approach for identifying compounds with adverse cellular effects during screening assays, potentially reducing compound rejection due to toxicity in subsequent in vitro and in vivo assays.

Cultural Parallax and Content Analysis: Images of Black Women in High School History Textbooks

Science.gov (United States)

Woyshner, Christine; Schocker, Jessica B.

2015-01-01

This study investigates the representation of Black women in high school history textbooks. To examine the extent to which Black women are represented visually and to explore how they are portrayed, the authors use a mixed-methods approach that draws on analytical techniques in content analysis and from visual culture studies. Their findings…

Effects of waste content of glass waste forms on Savannah River high-level waste disposal costs

International Nuclear Information System (INIS)

McDonell, W.R.; Jantzen, C.M.

1985-01-01

Effects of the waste content of glass waste forms of Savannah River high-level waste disposal costs are evaluated by their impact on the number of waste canisters produced. Changes in waste content affect onsite Defense Waste Processing Facility (DWPF) costs as well as offsite shipping and repository emplacement charges. A nominal 1% increase over the 28 wt % waste loading of DWPF glass would reduce disposal costs by about $50 million for Savannah River wastes generated to the year 2000. Waste form modifications under current study include adjustments of glass frit content to compensate for added salt decontamination residues and increased sludge loadings in the DWPF glass. Projected cost reductions demonstrate significant incentives for continued optimization of the glass waste loadings. 13 refs., 3 figs., 3 tabs

Biocompatible Ni-free Zr-based bulk metallic glasses with high-Zr-content: Compositional optimization for potential biomedical applications

Energy Technology Data Exchange (ETDEWEB)

Hua, Nengbin, E-mail: flower1982cn@126.com [Department of Materials Science and Engineering, Fujian University of Technology, 350118 Fuzhou (China); Department of Materials Science and Engineering, Fuzhou University, 350116 Fuzhou (China); Huang, Lu [Department of Materials Science and Engineering, The University of Tennessee, Knoxville, TN 37996-2100 (United States); Chen, Wenzhe [Department of Materials Science and Engineering, Fujian University of Technology, 350118 Fuzhou (China); Department of Materials Science and Engineering, Fuzhou University, 350116 Fuzhou (China); He, Wei [Department of Materials Science and Engineering, The University of Tennessee, Knoxville, TN 37996-2100 (United States); Department of Mechanical, Aerospace and Biomedical Engineering, The University of Tennessee, Knoxville, TN 37996-2200 (United States); Zhang, Tao [Key Laboratory of Aerospace Materials and Performance (Ministry of Education), School of Materials Science and Engineering, Beihang University, 100191 Beijing (China)

2014-11-01

The present study designs and prepares Ni-free Zr{sub 60+x}Ti{sub 2.5}Al{sub 10}Fe{sub 12.5−x}Cu{sub 10}Ag{sub 5} (at.%, x = 0, 2.5, 5) bulk metallic glasses (BMGs) by copper mold casting for potential biomedical application. The effects of Zr content on the in vitro biocompatibility of the Zr-based BMGs are evaluated by investigating mechanical properties, bio-corrosion behavior, and cellular responses. It is found that increasing the content of Zr is favorable for the mechanical compatibility with a combination of low Young's modulus, large plasticity, and high notch toughness. Electrochemical measurements demonstrate that the Zr-based BMGs are corrosion resistant in a phosphate buffered saline solution. The bio-corrosion resistance of BMGs is improved with the increase in Zr content, which is attributed to the enrichment in Zr and decrease in Al concentration in the surface passive film of alloys. Regular cell responses of mouse MC3T3-E1 cells, including cell adhesion and proliferation, are observed on the Zr–Ti–Al–Fe–Cu–Ag BMGs, which reveals their general biosafety. The high-Zr-based BMGs exhibit a higher cell proliferation activity in comparison with that of pure Zr and Ti-6Al-4V alloy. The effects of Zr content on the in vitro biocompatibility can be used to guide the future design of biocompatible Zr-based BMGs. - Highlights: • Ni-free Zr{sub 60+x}Ti{sub 2.5}Al{sub 10}Fe{sub 12.5−x}Cu{sub 10}Ag{sub 5} (at.%, x = 0, 2.5, 5) BMGs were fabricated. • Plasticity and notch toughness of BMGs are enhanced by high-Zr-content. • The high-Zr-based BMGs exhibit excellent bio-corrosion resistance in PBS solution. • The biosafety of BMGs is revealed by regular cell adhesion and proliferation. • High-Zr-bearing BMGs are favorable for potential applications as biomaterials.

Characterization of SPAD Array for Multifocal High-Content Screening Applications

Directory of Open Access Journals (Sweden)

Anthony Tsikouras

2016-10-01

Full Text Available Current instruments used to detect specific protein-protein interactions in live cells for applications in high-content screening (HCS are limited by the time required to measure the lifetime. Here, a 32 × 1 single-photon avalanche diode (SPAD array was explored as a detector for fluorescence lifetime imaging (FLIM in HCS. Device parameters and characterization results were interpreted in the context of the application to determine if the SPAD array could satisfy the requirements of HCS-FLIM. Fluorescence lifetime measurements were performed using a known fluorescence standard; and the recovered fluorescence lifetime matched literature reported values. The design of a theoretical 32 × 32 SPAD array was also considered as a detector for a multi-point confocal scanning microscope.

Classes of organic molecules targeted by a methanogenic microbial consortium grown on sedimentary rocks of various maturities

Directory of Open Access Journals (Sweden)

Margaux eMesle

2015-06-01

Full Text Available Organic-rich shales are populated by methanogenic consortia that are able to degrade the fossilized organic matter into methane gas. To identify the organic fraction effectively degraded, we have sequentially depleted two types of organic-rich rocks, shales and coal, at two different maturities, by successive solvent extractions to remove the most soluble fractions (maltenes and asphaltenes and isolate kerogen. We show the ability of the consortia to produce methane from all rock samples, including those containing the most refractory organic matter, i.e. the kerogen. Shales yielded higher methane production than lignite and coal. Mature rocks yielded more methane than immature rocks. Surprisingly, the efficiency of the consortia was not influenced by the removal of the easily biodegradable fractions contained in the maltenes and asphaltenes. This suggests that one of the limitations of organic matter degradation in situ may be the accessibility of the carbon and energy source. Indeed, bitumen has a colloidal structure that may limit the accessibility to asphaltenes in the bulk rock. Solvent extractions might favor the access to asphaltenes and kerogen by modifying the spatial organization of the molecules in the rock matrix.

Effects of Nitrogen Content on the HAZ Softening of Ti-Containing High Strength Steels Manufactured by Accelerated Cooling

Energy Technology Data Exchange (ETDEWEB)

Bang, Kook-soo; Jung, Ho-shin; Park, Chan [Pukyong National University, Busan (Korea, Republic of)

2017-03-15

The effects of nitrogen content on the HAZ softening of Ti-containing high strength steels manufactured by accelerating cooling were investigated and interpreted in terms of the microstructures in the softening zone. Regardless of their content, all of the steels investigated showed a softened zone 9-10 mm wide. The minimum hardness in the zone, however, was different, with lower hardness in the higher nitrogen content steel. Microstructural observations of the steel showed that the amount of soft ferrite was increased in the zone with an increase of nitrogen content of the steel, suggesting that microstructural evolution in the HAZ is influenced by the nitrogen content. Measurements of TiN particles showed that the degree of particles coarsening in the HAZ was lower in the higher nitrogen content steel. Therefore, it is believed that finer TiN particles in the HAZ inhibit austenite grain growth more effectively, and lead to an accelerated ferrite transformation in higher nitrogen content steel, resulting in a higher amount of soft ferrite microstructure in the softened zone.

Investigation of water content in primary upper shield of high temperature engineering test reactor (HTTR)

International Nuclear Information System (INIS)

Sumita, Junya; Sawa, Kazuhiro; Mogi, Haruyoshi; Itahashi, Shuuji; Kitami, Toshiyuki; Akutu, Youichi; Fuchita, Yasuhiro; Kawaguchi, Toru; Moriya, Masahiro

1999-09-01

A primary upper shield of the High Temperature Engineering Test Reactor (HTTR) is composed of concrete (grout) which is packed into iron frames. The main function of the primary upper shield is to attenuate neutron and gamma ray from the core, that leads to satisfy dose equivalent rate limit of operating floor and stand-pipe room. Water content in the concrete is one of the most important things because it strongly affects neutron-shielding ability. Then, we carried out out-of-pile experiments to investigate relationship between temperature and water content in the concrete. Based on the experimental results, a hydrolysis-diffusion model was developed to investigate water release behavior from the concrete. The model showed that water content used for shielding design in the primary upper shield of the HTTR will be maintained if temperature during operating life is under 110degC. (author)

A High Resolution Capacitive Sensing System for the Measurement of Water Content in Crude Oil

Science.gov (United States)

Aslam, Muhammad Zubair; Tang, Tong Boon

2014-01-01

This paper presents the design of a non-intrusive system to measure ultra-low water content in crude oil. The system is based on a capacitance to phase angle conversion method. Water content is measured with a capacitance sensor comprising two semi-cylindrical electrodes mounted on the outer side of a glass tube. The presence of water induces a capacitance change that in turn converts into a phase angle, with respect to a main oscillator. A differential sensing technique is adopted not only to ensure high immunity against temperature variation and background noise, but also to eliminate phase jitter and amplitude variation of the main oscillator that could destabilize the output. The complete capacitive sensing system was implemented in hardware and experiment results using crude oil samples demonstrated that a resolution of ±50 ppm of water content in crude oil was achieved by the proposed design. PMID:24967606

A High Resolution Capacitive Sensing System for the Measurement of Water Content in Crude Oil

Directory of Open Access Journals (Sweden)

Muhammad Zubair Aslam

2014-06-01

Full Text Available This paper presents the design of a non-intrusive system to measure ultra-low water content in crude oil. The system is based on a capacitance to phase angle conversion method. Water content is measured with a capacitance sensor comprising two semi-cylindrical electrodes mounted on the outer side of a glass tube. The presence of water induces a capacitance change that in turn converts into a phase angle, with respect to a main oscillator. A differential sensing technique is adopted not only to ensure high immunity against temperature variation and background noise, but also to eliminate phase jitter and amplitude variation of the main oscillator that could destabilize the output. The complete capacitive sensing system was implemented in hardware and experiment results using crude oil samples demonstrated that a resolution of ±50 ppm of water content in crude oil was achieved by the proposed design.

Preparation of culinary-medicinal king oyster mushroom Pleurotus eryngii-fermented products with high ergothioneine content and their taste quality.

Science.gov (United States)

Chen, Shih-Yu; Ho, Kung-Jui; Liang, Chih-Hung; Tsai, Ching-Hsuan; Huang, Ling-Yi; Mau, Jeng-Leun

2012-01-01

Pleurotus eryngii (DC. : Fr.) Ouel. was used in solid-state fermentation to develop novel mushroom products with a high amount of ergothioneine. The correlation coefficients between ergothioneine content and biomass were 0.8878 and 0.9206 for fermented adlay and buckwheat, respectively. Using optimal conditions, Pleurotus-fermented adlay and buckwheat (PFA and PFB) with the ergothioneine contents of 795.5 and 786.1 mg/ kg, respectively, were prepared. However, mycelia contained the highest ergothioneine content of 1514.6 mg/kg. As a result of SSF by P. eryngii, PFA and PFB contained more taste components than adlay and buckwheat, as evidenced by higher contents of total sugars and polyols, total free amino acids and monosodium glutamate-like components, and total and flavor 5'-nucleotides. In addition, PFB and buckwheat showed comparable equivalent umami concentration (EUC) values, whereas PFA showed a higher EUC value than adlay. Overall, Pleurotus-fermented products with a high amount of ergothioneine will be a novel functional food.

Corrosion resistance testing of high-boron-content stainless steels

International Nuclear Information System (INIS)

Petrman, I.; Safek, V.

1994-01-01

Boron steels, i.e. stainless steels with boron contents of 0.2 to 2.25 wt.%, are employed in nuclear engineering for the manufacture of baskets or wells in which radioactive fissile materials are stored, mostly spent nuclear fuel elements. The resistance of such steels to intergranular corrosion and uniform corrosion was examined in the Strauss solution and in boric acid; the dependence of the corrosion rate of the steels on their chemical composition was investigated, and their resistance was compared with that of AISI 304 type steel. Corrosion resistance tests in actual conditions of ''wet'' compact storage (demineralized water or a weak boric acid solution) gave evidence that boron steels undergo nearly no uniform corrosion and, as electrochemical measurements indicated, match standard corrosion-resistant steels. Corrosion resistance was confirmed to decrease slightly with increasing boron content and to increase somewhat with increasing molybdenum content. (Z.S.). 3 tabs., 4 figs., 7 refs

Influence of gross saponins from tribulus terrestris L on SOD activity and MDA content for chronic high intraocular pressure in rabbit

Directory of Open Access Journals (Sweden)

Nuo Li

2013-05-01

Full Text Available AIM:To observe influence of gross saponins from tribulus terrestris L(GSTTon SOD activity and MDA content for chronic high intraocular pressure in rabbit, and discusses the retina oxidative damage inhibition on chronic high intraocular pressure model of rabbit. METHODS:Totally 24 healthy New Zealand rabbits were randomly divided into 4 groups: normal control group(A group; high intraocular pressure model blank group(B group; high intraocular pressure model with GSTT treated group(C group; high intraocular pressure model with Erigeron brevicapas hand mass(EBHMtreated group(D group. High intraocular pressure model was induced by 20g/L methylcellulose injection into the anterior chamber in B group, C group and D group. D group was injected 5 mg/kg GSTT and C group was injected 4.5mg/kg EBHM and measured intraocular pressure with Schiotz tonometer every day for 4 weeks. The retina tissue superoxide dismutase(SODand maleic dialdehyde(MDAcontent were detected 28 days later. RESULTS: After glaucoma model of rabbit eyes were established, the intraocular pressure during observation period was maintained in 32-39mmHg; High intraocular pressure model blank group and normal control group, EBHM treatment group, GSTT treatment group were compared, the differences of retina MDA, SOD content had statistical significance(P0.05; EBHM treatment group, GSTT treatment group and normal control group were compared, the content of MDA in the retina was still slightly higher(P<0.05, the content of SOD slightly lower(P<0.05 CONCLUSION: GSTT can effectively improve the retina SOD activity of chronic high intraocular pressure in rabbit and reduce the content of MDA, which has a protective effect of persistent high intraocular retinal oxidative stress.

Molten salt oxidation of organic hazardous waste with high salt content.

Science.gov (United States)

Lin, Chengqian; Chi, Yong; Jin, Yuqi; Jiang, Xuguang; Buekens, Alfons; Zhang, Qi; Chen, Jian

2018-02-01

Organic hazardous waste often contains some salt, owing to the widespread use of alkali salts during industrial manufacturing processes. These salts cause complications during the treatment of this type of waste. Molten salt oxidation is a flameless, robust thermal process, with inherent capability of destroying the organic constituents of wastes, while retaining the inorganic ingredients in the molten salt. In the present study, molten salt oxidation is employed for treating a typical organic hazardous waste with a high content of alkali salts. The hazardous waste derives from the production of thiotriazinone. Molten salt oxidation experiments have been conducted using a lab-scale molten salt oxidation reactor, and the emissions of CO, NO, SO 2 , HCl and dioxins are studied. Impacts are investigated from the composition of the molten salts, the types of feeding tube, the temperature of molten carbonates and the air factor. Results show that the waste can be oxidised effectively in a molten salt bath. Temperature of molten carbonates plays the most important role. With the temperature rising from 600 °C to 750 °C, the oxidation efficiency increases from 91.1% to 98.3%. Compared with the temperature, air factor has but a minor effect, as well as the composition of the molten salts and the type of feeding tube. The molten carbonates retain chlorine with an efficiency higher than 99.9% and the emissions of dioxins are below 8 pg TEQ g -1 sample. The present study shows that molten salt oxidation is a promising alternative for the disposal of organic hazardous wastes containing a high salt content.

[Impact of Thermal Treatment on Biogas Production by Anaerobic Digestion of High-solid-content Swine Manure].

Science.gov (United States)

Hu, Yu-ying; Wu, Jing; Wang, Shi-feng; Cao, Zhi-ping; Wang, Kai-jun; Zuo, Jian-e

2015-08-01

Livestock manure is a kind of waste with high organic content and sanitation risk. In order to investigate the impact of thermal treatment on the anaerobic digestion of high-solid-content swine manure, 70 degrees C thermal treatment was conducted to treat raw manure (solid content 27.6%) without any dilution. The results indicated that thermal treatment could reduce the organic matters and improve the performance of anaerobic digestion. When the thermal treatment time was 1d, 2d, 3d, 4d, the VS removal rates were 15.1%, 15.5%, 17.8% and 20.0%, respectively. The methane production rates (CH4/VSadd) were 284.4, 296.3, 309.2 and 264.4 mL x g(-1), which was enhanced by 49.7%, 55.9%, 62.7% and 39.2%, respectively. The highest methane production rate occurred when the thermal treatment time was 3d. The thermal treatment had an efficient impact on promoting the performance of methane production rate with a suitable energy consumption. On the other hand, thermal treatment could act as pasteurization. This showed that thermal treatment would be of great practical importance.

Profiling stem cell states in three-dimensional biomaterial niches using high content image informatics.

Science.gov (United States)

Dhaliwal, Anandika; Brenner, Matthew; Wolujewicz, Paul; Zhang, Zheng; Mao, Yong; Batish, Mona; Kohn, Joachim; Moghe, Prabhas V

2016-11-01

A predictive framework for the evolution of stem cell biology in 3-D is currently lacking. In this study we propose deep image informatics of the nuclear biology of stem cells to elucidate how 3-D biomaterials steer stem cell lineage phenotypes. The approach is based on high content imaging informatics to capture minute variations in the 3-D spatial organization of splicing factor SC-35 in the nucleoplasm as a marker to classify emergent cell phenotypes of human mesenchymal stem cells (hMSCs). The cells were cultured in varied 3-D culture systems including hydrogels, electrospun mats and salt leached scaffolds. The approach encompasses high resolution 3-D imaging of SC-35 domains and high content image analysis (HCIA) to compute quantitative 3-D nuclear metrics for SC-35 organization in single cells in concert with machine learning approaches to construct a predictive cell-state classification model. Our findings indicate that hMSCs cultured in collagen hydrogels and induced to differentiate into osteogenic or adipogenic lineages could be classified into the three lineages (stem, adipogenic, osteogenic) with ⩾80% precision and sensitivity, within 72h. Using this framework, the augmentation of osteogenesis by scaffold design exerted by porogen leached scaffolds was also profiled within 72h with ∼80% high sensitivity. Furthermore, by employing 3-D SC-35 organizational metrics, differential osteogenesis induced by novel electrospun fibrous polymer mats incorporating decellularized matrix could also be elucidated and predictably modeled at just 3days with high precision. We demonstrate that 3-D SC-35 organizational metrics can be applied to model the stem cell state in 3-D scaffolds. We propose that this methodology can robustly discern minute changes in stem cell states within complex 3-D architectures and map single cell biological readouts that are critical to assessing population level cell heterogeneity. The sustained development and validation of bioactive

Austenitic stainless steel alloys with high nickel contents in high temperature liquid metal systems

International Nuclear Information System (INIS)

Konvicka, H.R.; Schwarz, N.F.

1981-01-01

Fe-Cr-Ni base alloys (nickel content: from 15 to 70 wt%, Chromium content: 15 wt%, iron: balance) together with stainless steel (W.Nr. 1.4981) have been exposed to flowing liquid sodium at 730 0 C in four intervals up to a cumulative exposure time of 1500 hours. Weight change data and the results of post-exposition microcharacterization of specimens are reported. The corrosion rates increase with increasing nickel content and tend to become constant after longer exposure times for each alloy. The corrosion rate of stainless steel is considerably reduced due to the presence of the base alloys. Different kinetics of nickel poor (up to 35% nickel) and nickel rich (> 50% nickel) alloys and nickel transport from nickel rich to nickel poor material is observed. (orig.)

Efficiency of phosphate fertilization to maize crop in high phosphorus content soil, evaluated by 32P tracer

International Nuclear Information System (INIS)

Trevizam, Anderson R.; Alvarez Villanueva, Felipe C.; Silva, Maria Ligia de S.; Muraoka, Takashi

2007-01-01

Application of high dosis of phosphorus (P) in agricultural soils is justified by its intense fixation by the soil clays, which reduce availability to crops. The objective of this research was to evaluate the response of maize crops to five rates of triple superphosphate in a soil with high available phosphorus content. Portions of 2 dm 3 of soil (Typic Quartzipisamment) with 75 mg kg -1 of available phosphorus and pH 7.00, collected from the upper 0-20 cm layer, were placed in plastic pots, received solution containing 5.55 MBq (150 μCi) of 32 P and incubated for 7 days. Then 0, 250, 500, 1000 and 4000 mg P kg -1 as triple superphosphate was added to soil in the respective pots and incubated for 15 days keeping the soil moisture to 60 % of the field capacity. Maize (Zea mays L.) plants, single hybrid P30F80, were grown for 50 days (after germination), collected, oven dried, weighed and ground in a Wiley mill for analysis of total P content and 32 P radioactivity. The maize dry matter increased with triple superphosphate rates. The phosphorus content and accumulation in the maize plants increased with triple superphosphate rate up to 4000 mg kg -1 . The percentage of phosphorus derived from the fertilizer ranged from 79 to 97% and consequently the phosphorus derived from soil decreased with increasing application of triple superphosphate. In spite of soil high P available content, maize plants responded to applied phosphorus rates. (author)

Production of JET fuel containing molecules of high hydrogen content

Directory of Open Access Journals (Sweden)

Tomasek Sz.

2017-12-01

Full Text Available The harmful effects of aviation can only be reduced by using alternative fuels with excellent burning properties and a high hydrogen content in the constituent molecules. Due to increasing plastic consumption the amount of the plastic waste is also higher. Despite the fact that landfill plastic waste has been steadily reduced, the present scenario is not satisfactory. Therefore, the aim of this study is to produce JET fuel containing an alternative component made from straight-run kerosene and the waste polyethylene cracking fraction. We carried out our experiments on a commercial NiMo/Al2O3/P catalyst at the following process parameters: T=200-300°C, P=40 bar, LHSV=1.0-3.0 h-1, hydrogen/hydrocarbon ratio= 400 Nm3/m3. We investigated the effects of the feedstocks and the process parameters on the product yields, the hydrodesulfurization and hydrodearomatization efficiencies, and the main product properties. The liquid product yields varied between 99.7-99.8%. As a result of the hydrogenation the sulfur (1-1780 mg/kg and the aromatic contents (9.0-20.5% of the obtained products and the values of their smoke points (26.0-34.7 mm fulfilled the requirements of JET fuel standard. Additionally, the concentration of paraffins increased in the products and the burning properties were also improved. The freezing points of the products were higher than -47°C, therefore product blending is needed.

A High-Content Live-Cell Viability Assay and Its Validation on a Diverse 12K Compound Screen.

Science.gov (United States)

Chiaravalli, Jeanne; Glickman, J Fraser

2017-08-01

We have developed a new high-content cytotoxicity assay using live cells, called "ImageTOX." We used a high-throughput fluorescence microscope system, image segmentation software, and the combination of Hoechst 33342 and SYTO 17 to simultaneously score the relative size and the intensity of the nuclei, the nuclear membrane permeability, and the cell number in a 384-well microplate format. We then performed a screen of 12,668 diverse compounds and compared the results to a standard cytotoxicity assay. The ImageTOX assay identified similar sets of compounds to the standard cytotoxicity assay, while identifying more compounds having adverse effects on cell structure, earlier in treatment time. The ImageTOX assay uses inexpensive commercially available reagents and facilitates the use of live cells in toxicity screens. Furthermore, we show that we can measure the kinetic profile of compound toxicity in a high-content, high-throughput format, following the same set of cells over an extended period of time.

Simple statistical model for branched aggregates

DEFF Research Database (Denmark)

Lemarchand, Claire; Hansen, Jesper Schmidt

2015-01-01

, given that it already has bonds with others. The model is applied here to asphaltene nanoaggregates observed in molecular dynamics simulations of Cooee bitumen. The variation with temperature of the probabilities deduced from this model is discussed in terms of statistical mechanics arguments....... The relevance of the statistical model in the case of asphaltene nanoaggregates is checked by comparing the predicted value of the probability for one molecule to have exactly i bonds with the same probability directly measured in the molecular dynamics simulations. The agreement is satisfactory......We propose a statistical model that can reproduce the size distribution of any branched aggregate, including amylopectin, dendrimers, molecular clusters of monoalcohols, and asphaltene nanoaggregates. It is based on the conditional probability for one molecule to form a new bond with a molecule...

High-content analysis of single cells directly assembled on CMOS sensor based on color imaging.

Science.gov (United States)

Tanaka, Tsuyoshi; Saeki, Tatsuya; Sunaga, Yoshihiko; Matsunaga, Tadashi

2010-12-15

A complementary metal oxide semiconductor (CMOS) image sensor was applied to high-content analysis of single cells which were assembled closely or directly onto the CMOS sensor surface. The direct assembling of cell groups on CMOS sensor surface allows large-field (6.66 mm×5.32 mm in entire active area of CMOS sensor) imaging within a second. Trypan blue-stained and non-stained cells in the same field area on the CMOS sensor were successfully distinguished as white- and blue-colored images under white LED light irradiation. Furthermore, the chemiluminescent signals of each cell were successfully visualized as blue-colored images on CMOS sensor only when HeLa cells were placed directly on the micro-lens array of the CMOS sensor. Our proposed approach will be a promising technique for real-time and high-content analysis of single cells in a large-field area based on color imaging. Copyright © 2010 Elsevier B.V. All rights reserved.

Thermogravimetric Analysis of Effects of High-Content Limstone Addition on Combustion Characteristics of Taixi Anthracite

Institute of Scientific and Technical Information of China (English)

ZHANG Hong; LI Mei; SUN Min; WEI Xian-yong

2004-01-01

Combustion characteristics of Taixi anthracite admixed with high content of limestone addition were investigated with thermogravimetric analysis. The results show that limestone addition has a little promoting effect on the ignition of raw coals as a whole. The addition of limestone is found to significantly accelerate the combustion and burnout of raw coals. The higher the sample mass is, the more significant the effect will be. The results also show that the change of limestone proportion between 45%-80% has little effect on ignition temperatures of coal in the blended samples. Increasing limestone content lowers the temperature corresponding to the maximum weight loss. Although higher maximum mass loss rates are observed with higher limestone content, the effect is found not ascribed to changing limestone addition, but to the decrease of absolute coal mass in the sample. The change of limestone proportion has little effect on its burnout temperature. Mechanism analysis indicates that these phenomena result mainly from improved heat conduction due to limestone addition.

Bonding Characteristics and Chemical Inertness of Zr–Si–N Coatings with a High Si Content in Glass Molding

Directory of Open Access Journals (Sweden)

Li-Chun Chang

2018-05-01

Full Text Available High-Si-content transition metal nitride coatings, which exhibited an X-ray amorphous phase, were proposed as protective coatings on glass molding dies. In a previous study, the Zr–Si–N coatings with Si contents of 24–30 at.% exhibited the hardness of Si3N4, which was higher than those of the middle-Si-content (19 at.% coatings. In this study, the bonding characteristics of the constituent elements of Zr–Si–N coatings were evaluated through X-ray photoelectron spectroscopy. Results indicated that the Zr 3d5/2 levels were 179.14–180.22 and 180.75–181.61 eV for the Zr–N bonds in ZrN and Zr3N4 compounds, respectively. Moreover, the percentage of Zr–N bond in the Zr3N4 compound increased with increasing Si content in the Zr–Si–N coatings. The Zr–N bond of Zr3N4 dominated when the Si content was >24 at.%. Therefore, high Si content can stabilize the Zr–N compound in the M3N4 bonding structure. Furthermore, the thermal stability and chemical inertness of Zr–Si–N coatings were evaluated by conducting thermal cycle annealing at 270 °C and 600 °C in a 15-ppm O2–N2 atmosphere. The results indicated that a Zr22Si29N49/Ti/WC assembly was suitable as a protective coating against SiO2–B2O3–BaO-based glass for 450 thermal cycles.

Morphometric Characterization of Rat and Human Alveolar Macrophage Cell Models and their Response to Amiodarone using High Content Image Analysis.

Science.gov (United States)

Hoffman, Ewelina; Patel, Aateka; Ball, Doug; Klapwijk, Jan; Millar, Val; Kumar, Abhinav; Martin, Abigail; Mahendran, Rhamiya; Dailey, Lea Ann; Forbes, Ben; Hutter, Victoria

2017-12-01

Progress to the clinic may be delayed or prevented when vacuolated or "foamy" alveolar macrophages are observed during non-clinical inhalation toxicology assessment. The first step in developing methods to study this response in vitro is to characterize macrophage cell lines and their response to drug exposures. Human (U937) and rat (NR8383) cell lines and primary rat alveolar macrophages obtained by bronchoalveolar lavage were characterized using high content fluorescence imaging analysis quantification of cell viability, morphometry, and phospholipid and neutral lipid accumulation. Cell health, morphology and lipid content were comparable (p content. Responses to amiodarone, a known inducer of phospholipidosis, required analysis of shifts in cell population profiles (the proportion of cells with elevated vacuolation or lipid content) rather than average population data which was insensitive to the changes observed. A high content image analysis assay was developed and used to provide detailed morphological characterization of rat and human alveolar-like macrophages and their response to a phospholipidosis-inducing agent. This provides a basis for development of assays to predict or understand macrophage vacuolation following inhaled drug exposure.

Peel and pulp of baru (Dipteryx Alata Vog. provide high fiber, phenolic content and antioxidant capacity

Directory of Open Access Journals (Sweden)

Gabriela de Lima SANTIAGO

2018-03-01

Full Text Available Abstract Baru (Dipteryx alata Vog. is a native fruit of the Brazilian Savannah that can be used in the food industry and may contribute to the economy of the Brazilian Midwest. The proximate composition, the phenolic content and the antioxidant capacity of the peel, pulp and raw and roasted baru almond were examined and compared. Peel showed higher concentrations of dietary fibers (24.1 g/100 g followed by pulp and roasted almond (18 g/100 g and 16 g/100 g, respectively, and raw almond (12.0 g/100 g. However, the almonds presented the highest lipid and protein concentrations compared to baru peel and pulp. In addition, raw almond showed the highest total phenolic contents (1,107.0 mg GAE/100 g and antioxidant capacity, but the roasted almond, and baru peel with its pulp, also presented high phenolic contents. The correlation coefficients between phenolic content and antioxidant capacity (via ABTS and FRAP were strong and significant. The chemical composition of baru peel has not previously been reported. The results showed promising prospects for the consumption of baru pulp with its peel, the fruit component richest in fiber, whose phenolic content and antioxidant capacity are comparable to those of the baru almond.

Automated High-Performance Liquid Chromatography Saturate, Aromatic, Resin, and Asphaltene Separation

Science.gov (United States)

2016-10-01

Dividing a material into its constituent parts is necessary to define its composition. These compositional analyses are useful in binder formulation through blending, rejuvenation, and modification, as well as prediction of physical performance. Norm...

Thermodynamic-state and kinetic-process dependent dual ferromagnetic states in high-Si content FeMn(PSi) alloys

International Nuclear Information System (INIS)

Li, Guijiang; Eriksson, Olle; Johansson, Börje; Vitos, Levente

2015-01-01

We have found that thermodynamic state and kinetic process co-determine the dual ferromagnetic (FM) orders in high-Si content FeMnP 1−x Si x (0.25 < x < 0.5). Alloys undergoing high temperature annealing and quenching process prefer a high magnetic moment FM state in a chemically partial disordered structure with low c/a ratio. This mechanism is suggested to be responsible for the often discussed virgin effect as well. A chemically ordered structure obtained by a slow cooling process from a relatively low annealing temperature and the increase in Si content stabilize a metastable lattice with high c/a ratio and FM order with low magnetic moment. The non-simultaneity of the magnetic and structural transitions can be responsible for the occurrence of FM state in the high c/a range. Thus, a c/a ratio that changes from high to low is physically plausible to stabilize the metastable FM order at low temperature. Our theoretical observations indicate that suitable thermodynamic state and kinetic diffusion process is crucial for optimizing magnetocaloric properties and exploring feasible magnetocaloric materials

High water contents in basaltic melt inclusions from Arenal volcano, Costa Rica

Science.gov (United States)

Wade, J. A.; Plank, T.; Hauri, E. H.; Melson, W. G.; Soto, G. J.

2004-12-01

Despite the importance of water to arc magma genesis, fractionation and eruption, few quantitative constraints exist on the water content of Arenal magmas. Early estimates, by electron microprobe sum deficit, suggested up to 4 wt% H2O in olivine-hosted basaltic andesite melt inclusions (MI) from pre-historic ET-6 tephra (Melson, 1982), and up to 7 wt% H2O in plagioclase and orthopyroxene-hosted dacitic MI from 1968 lapilli (Anderson, 1979). These high water contents are consistent with abundant hornblende phenocrysts in Arenal volcanics, but inconsistent with geochemical tracers such as 10Be and Ba/La that suggest a low flux of recycled material (and presumably water) from the subduction zone. In order to test these ideas, and provide the first direct measurements of water in mafic Arenal magmas, we have studied olivine-hosted MI from the prehistoric (900 yBP; Soto et al., 1998) ET3 tephra layer. MI range from andesitic (> 58% SiO2) to basaltic compositions ( 4 wt%) found here for Arenal basaltic MI support the semi-quantitative data from earlier studies, but are somewhat unexpected given predictions from slab tracers. Arenal water contents (4%) approach those of the 1995 eruption of Cerro Negro in Nicaragua (4-5 wt% in basaltic MI; Roggensack et al., 1997), despite the fact that the latter has Ba/La of > 100, while Arenal has Ba/La Journal of Geology; Melson, William G. (1982) Boletin de Volcanologia; Roggensack et al. (1997) Science; Soto et al. (1998) OSIVAM; Williams-Jones et al. (2001) Journal of Volc. and Geoth. Res.

Remedial measures in Czech houses with high radium content in building material

International Nuclear Information System (INIS)

Hulka, J.; Thomas, J.

1999-01-01

Three groups of houses built from materials having elevated natural radioactivity content were found in the Czech republic. These are: 1) about hundred old houses in Jachymov (Joachimstal) in Northern Bohemia, where residues from factory producing uranium paints were used as plaster and mortar before the World War II (radium concentration up to 1 MBq/kg, indoor gamma dose rate up to 10-100 μGy/h); 2) some 20 000 family houses built from highly emanating aerated concrete with radium content 500-1000 Bq/kg (produced from flying ash) in the period 1963-1980; 3) more than 2000 family houses from slag concrete of radium content about 3 kBq/kg in average (indoor gamma dose rate up to 2 μGy/h) made in the period 1972-83. Remedy measures were undertaken with state financial support. Intervention levels were laid down 200 Bq/m 3 for EEC (equivalent equilibrium radon concentration - it is equivalent to radon gas concentration 500 Bq/m 3 ), 2 μGy/h for indoor gamma dose rate. Weighted sum of indoor radon and indoor gamma dose rate was used if the latter was above 0,5 μGy/h. The central heat recovery ventilation units were used largely as the remedy measures. Some houses were demolished, in some houses local contamination of plasters was removed. Other tested measures (removal of the contaminated building material in great amount, gamma shielding, wall coating, etc.) proved to be not effective or not acceptable in practice. (author)

High Neonatal Blood Iron Content Is Associated with the Risk of Childhood Type 1 Diabetes Mellitus

Directory of Open Access Journals (Sweden)

Julie Nyholm Kyvsgaard

2017-11-01

Full Text Available (1 Background: Iron requirement increases during pregnancy and iron supplementation is therefore recommended in many countries. However, excessive iron intake may lead to destruction of pancreatic β-cells. Therefore, we aim to test if higher neonatal iron content in blood is associated with the risk of developing type 1 diabetes mellitus (T1D in childhood; (2 Methods: A case-control study was conducted, including 199 children diagnosed with T1D before the age of 16 years from 1991 to 2005 and 199 controls matched on date of birth. Information on confounders was available in 181 cases and 154 controls. Iron was measured on a neonatal single dried blood spot sample and was analyzed by laser ablation inductively coupled plasma mass spectrometry. Multivariate logistic regression was used to evaluate if iron content in whole blood was associated with the risk of T1D; (3 Results: A doubling of iron content increased the odds of developing T1D more than two-fold (odds ratio (95% CI, 2.55 (1.04; 6.24. Iron content increased with maternal age (p = 0.04 and girls had higher content than boys (p = 0.01; (4 Conclusions: Higher neonatal iron content associates to an increased risk of developing T1D before the age of 16 years. Iron supplementation during early childhood needs further investigation, including the causes of high iron in neonates.

Submerged cultivation of mycelium with high ergothioneine content from the culinary-medicinal king oyster mushroom Pleurotus eryngii (higher Basidiomycetes) and its composition.

Science.gov (United States)

Liang, Chih-Hung; Huang, Ling-Yi; Ho, Kung-Jui; Lin, Shin-Yi; Mau, Jeng-Leun

2013-01-01

The culinary-medicinal king oyster mushroom, Pleurotus eryngii, was used to produce mycelia with high ergothioneine content using a one-factor-at-a-time method. The optimal culture conditions for mycelia harvested at day 14 were 25°C, 10% inoculation rate, 2% glucose, 0.5% yeast extract, and no adjustment to the initial pH value. With histidine or amino acid mix added, biomasses and the ergothioneine content of mycelia were higher than those of the control. The ergothioneine content of mycelia harvested at days 16-20 were higher than that of mycelia harvested at day 14. In addition, the ergothioneine content of mycelia from the fermentor (5.84-5.76 mg/g) was much higher than that of mycelia from the shaken flask (4.93-5.04 mg/g). Mycelia with high ergothioneine content showed a profile of proximate composition similar to that of regular mycelia but lost its characteristic umami taste. Overall, mycelia high in ergothioneine could be prepared by optimal culture conditions, the addition of precursors, prolonged harvest, and aeration in the fermentor.

Biodiesel from the seed oil of Treculia africana with high free fatty acid content

Energy Technology Data Exchange (ETDEWEB)

Adewuyi, Adewale [Redeemer' s University, Department of Chemical Sciences, Faculty of Natural Sciences, Redemption City, Ogun State (Nigeria); Oderinde, Rotimi A.; Ojo, David F.K. [University of Ibadan, Industrial Unit, Department of Chemistry, Ibadan, Oyo State (Nigeria)

2012-12-15

Oil was extracted from the seed of Treculia africana using hexane. The oil was characterized and used in the production of biodiesel. Biodiesel was produced from the seed oil of T. africana using a two-step reaction system. The first step was a pretreatment which involved the use of 2 % sulfuric acid in methanol, and secondly, transesterification reaction using KOH as catalyst. Saponification value of the oil was 201.70 {+-} 0.20 mg KOH/g, free fatty acid was 8.20 {+-} 0.50 %, while iodine value was 118.20 {+-} 0.50 g iodine/100 g. The most dominant fatty acid was C18:2 (44 %). The result of the method applied showed a conversion which has ester content above 98 %, flash point of 131 {+-} 1.30 C, and phosphorus content below 1 ppm in the biodiesel. The biodiesel produced exhibited properties that were in agreement with the European standard (EN 14214). This study showed that the high free fatty acid content of T. africana seed oil can be reduced in a one-step pretreatment of esterification reaction using H{sub 2}SO{sub 4} as catalyst. (orig.)

Adsorption of sulfamethoxazole and sulfapyridine antibiotics in high organic content soils.

Science.gov (United States)

Chen, Kuen-Lin; Liu, Li-Chun; Chen, Wan-Ru

2017-12-01

Many antibiotics, including sulfonamides, are being frequently detected in soil and groundwater. Livestock waste is an important source of antibiotic pollution, and sulfonamides may be present along with organic-rich substances. This study aims to investigate the sorption reaction of two sulfonamides, sulfamethoxazole (SMZ) and sulfapyridine (SPY) in two organic-rich sorbents: a commercial peat soil (38.41% carbon content) and a composted manure (24.33% carbon content). Batch reactions were conducted to evaluate the impacts of pH (4.5-9.5) and background ions (0.001 M-0.1 M CaCl 2 ) on their sorption. Both linear partitioning and Freundlich sorption isotherms fit the reaction well. The n values of Freundlich isotherm were close to 1 in most conditions suggesting that the hydrophobic partition is the major adsorption mechanism. In terms of SMZ, K d declined with increases in the pH. SPY has a pyridine group that is responsible for adsorption at high pH values, and thus, no significant trend between K d and pH was observed. At high pH ranges, SPY sorption deviated significantly from linear partitioning. The results suggested the sorption mechanism of these two sulfonamide antibiotics tended to be hydrophobic partitioning under most of the experimental conditions, especially at pH values lower than their corresponding pK a2. The fluorescence excitation emission matrix and dissolved organic carbon leaching test suggested composted manure has higher fulvic acid organics and that peat soil has higher humus-like organics. Small organic molecules showed stronger affinity toward sulfonamide antibiotics and cause the composted manure to exhibit higher sorption capacity. Overall, this study suggests that the chemical structure and properties of sulfonamides antibiotics and the type of organic matter in soils will greatly influence the fate and transport of these contaminants into the environment. Copyright © 2017 Elsevier Ltd. All rights reserved.

High content analysis of differentiation and cell death in human adipocytes.

Science.gov (United States)

Doan-Xuan, Quang Minh; Sarvari, Anitta K; Fischer-Posovszky, Pamela; Wabitsch, Martin; Balajthy, Zoltan; Fesus, Laszlo; Bacso, Zsolt

2013-10-01

Understanding adipocyte biology and its homeostasis is in the focus of current obesity research. We aimed to introduce a high-content analysis procedure for directly visualizing and quantifying adipogenesis and adipoapoptosis by laser scanning cytometry (LSC) in a large population of cell. Slide-based image cytometry and image processing algorithms were used and optimized for high-throughput analysis of differentiating cells and apoptotic processes in cell culture at high confluence. Both preadipocytes and adipocytes were simultaneously scrutinized for lipid accumulation, texture properties, nuclear condensation, and DNA fragmentation. Adipocyte commitment was found after incubation in adipogenic medium for 3 days identified by lipid droplet formation and increased light absorption, while terminal differentiation of adipocytes occurred throughout day 9-14 with characteristic nuclear shrinkage, eccentric nuclei localization, chromatin condensation, and massive lipid deposition. Preadipocytes were shown to be more prone to tumor necrosis factor alpha (TNFα)-induced apoptosis compared to mature adipocytes. Importantly, spontaneous DNA fragmentation was observed at early stage when adipocyte commitment occurs. This DNA damage was independent from either spontaneous or induced apoptosis and probably was part of the differentiation program. © 2013 International Society for Advancement of Cytometry. Copyright © 2013 International Society for Advancement of Cytometry.

High-content screening of small compounds on human embryonic stem cells.

Science.gov (United States)

Barbaric, Ivana; Gokhale, Paul J; Andrews, Peter W

2010-08-01

Human ES (embryonic stem) cells and iPS (induced pluripotent stem) cells have been heralded as a source of differentiated cells that could be used in the treatment of degenerative diseases, such as Parkinson's disease or diabetes. Despite the great potential for their use in regenerative therapy, the challenge remains to understand the basic biology of these remarkable cells, in order to differentiate them into any functional cell type. Given the scale of the task, high-throughput screening of agents and culture conditions offers one way to accelerate these studies. The screening of small-compound libraries is particularly amenable to such high-throughput methods. Coupled with high-content screening technology that enables simultaneous assessment of multiple cellular features in an automated and quantitative way, this approach is proving powerful in identifying both small molecules as tools for manipulating stem cell fates and novel mechanisms of differentiation not previously associated with stem cell biology. Such screens performed on human ES cells also demonstrate the usefulness of human ES/iPS cells as cellular models for pharmacological testing of drug efficacy and toxicity, possibly a more imminent use of these cells than in regenerative medicine.

High GC content causes orphan proteins to be intrinsically disordered.

Directory of Open Access Journals (Sweden)

Walter Basile

2017-03-01

Full Text Available De novo creation of protein coding genes involves the formation of short ORFs from noncoding regions; some of these ORFs might then become fixed in the population. These orphan proteins need to, at the bare minimum, not cause serious harm to the organism, meaning that they should for instance not aggregate. Therefore, although the creation of short ORFs could be truly random, the fixation should be subjected to some selective pressure. The selective forces acting on orphan proteins have been elusive, and contradictory results have been reported. In Drosophila young proteins are more disordered than ancient ones, while the opposite trend is present in yeast. To the best of our knowledge no valid explanation for this difference has been proposed. To solve this riddle we studied structural properties and age of proteins in 187 eukaryotic organisms. We find that, with the exception of length, there are only small differences in the properties between proteins of different ages. However, when we take the GC content into account we noted that it could explain the opposite trends observed for orphans in yeast (low GC and Drosophila (high GC. GC content is correlated with codons coding for disorder promoting amino acids. This leads us to propose that intrinsic disorder is not a strong determining factor for fixation of orphan proteins. Instead these proteins largely resemble random proteins given a particular GC level. During evolution the properties of a protein change faster than the GC level causing the relationship between disorder and GC to gradually weaken.

The differences in Hg content released from high copper amalgam and silverfil argentum restoration into artificial saliva after one week of soaking (in vitro

Directory of Open Access Journals (Sweden)

Deriz Rieskanoerbachra Wisuardy

2008-07-01

Full Text Available Dental restoration is a treatment in dentistry that very often implemented. One of the restoration materials used is an amalgam. Amalgam has some deficiencies, among others, the presence of free Hg. The purpose of this study was to find out the difference in Hg content released from two different kinds of amalgam, namely, high copper amalgam and silverfil argentum carried out in vitro. This study was carried out on thirty premolar teeth of the maxilla which underwent class one occlusal restoration. The Hg content released was measured using the Atomic Absorption Spectrophotometry (AAS. This was a quasi-experimental study. The study results analyzed using the independent t paired statistical test method indicated that after one week of immersion, the average Hg content released from high copper amalgam restoration was 10,695 ng/mL and from silverfil argentum restoration was 5,602 ng/mL. The conclusion of the study was that there was a difference in Hg content released from high copper amalgam restoration and silverfil argentum restoration. The Hg content released from high copper amalgam restoration was higher than the Hg content released from silverfil argentum restoration.

Fructose content in popular beverages made with and without high-fructose corn syrup.

Science.gov (United States)

Walker, Ryan W; Dumke, Kelly A; Goran, Michael I

2014-01-01

Excess fructose consumption is hypothesized to be associated with risk for metabolic disease. Actual fructose consumption levels are difficult to estimate because of the unlabeled quantity of fructose in beverages. The aims of this study were threefold: 1) re-examine the fructose content in previously tested beverages using two additional assay methods capable of detecting other sugars, especially maltose, 2) compare data across all methods to determine the actual free fructose-to-glucose ratio in beverages made either with or without high-fructose corn syrup (HFCS), and 3) expand the analysis to determine fructose content in commonly consumed juice products. Sugar-sweetened beverages (SSBs) and fruit juice drinks that were either made with or without HFCS were analyzed in separate, independent laboratories via three different methods to determine sugar profiles. For SSBs, the three independent laboratory methods showed consistent and reproducible results. In SSBs made with HFCS, fructose constituted 60.6% ± 2.7% of sugar content. In juices sweetened with HFCS, fructose accounted for 52.1% ± 5.9% of sugar content, although in some juices made from 100% fruit, fructose concentration reached 65.35 g/L accounting for 67% of sugars. Our results provide evidence of higher than expected amounts of free fructose in some beverages. Popular beverages made with HFCS have a fructose-to-glucose ratio of approximately 60:40, and thus contain 50% more fructose than glucose. Some pure fruit juices have twice as much fructose as glucose. These findings suggest that beverages made with HFCS and some juices have a sugar profile very different than sucrose, in which amounts of fructose and glucose are equivalent. Current dietary analyses may underestimate actual fructose consumption. Copyright © 2014 The Authors. Published by Elsevier Inc. All rights reserved.

Mechanical Property and Analysis of Asphalt Components Based on Molecular Dynamics Simulation

Directory of Open Access Journals (Sweden)

Rui Li

2017-01-01

Full Text Available The asphalt-aggregate interface interaction plays a significant role in the overall performances of asphalt mixture. In order to analyze the chemical constitution of asphalt effects on the asphalt-aggregate interaction, the average structure C64H52S2 is selected to represent the asphalt, and the colloid, saturated phenol, and asphaltene are selected to represent the major constitutions in asphalt. The molecular models are established for the three compositions, respectively, and the Molecular Dynamics (MD simulation was conducted for the three kinds of asphaltene-aggregate system at different presses. Comparing the E value of Young modulus of these three polymers, the maximum modulus value of asphaltene was 2.80 GPa, the modulus value of colloid was secondary, and the minimum modulus of saturated phenol was 0.52 GPa. This result corresponds to conventional understanding.

High Solid Contents Copoly (Styrene/Butyl Acrylate-Cloisite 30B Nanocomposites

Directory of Open Access Journals (Sweden)

M. Mirzataheri

2013-03-01

Full Text Available Higher solid contents (20 % and 40 % nanocomposites of poly (styrene-co-butyl acrylate including higher content of Cloisite 30B (7 wt% and 10 wt % were prepared via miniemulsion polymerization. Stability of the final latexes proved outstanding combination of polymerization procedure and surfactants. Morphological studies revealed by TEM, SAX and XRD showed three structures of core-shell, armored and individual dispersion of clay layers within the polymer particles. The effect of Cloisite 30B content on the barrier properties presents excellent and wide use of these films for packaging and nanocoatings industries.

High-performance liquid chromatographic determination of β-carotene content in four varieties of lotus stamens

Directory of Open Access Journals (Sweden)

Nithida Phonkot

2010-08-01

Full Text Available A high-performance liquid chromatography method was developed to determine -carotene content in lotus stamens.The stamens of four varieties of Nelumbo nucifera (Gaertn. and ten samples bought from traditional drug stores were determined.Validation of the method was carried out, the linearity of the -carotene concentrations range from 6.50-58.50 g.mL-1were 0.9997-0.9998. The repeatability and intermediate precision were 0.29 %CV (n=9 and 7.48 %CV (n=9, respectively; theaccuracy was 100.10 %w/w, the detection limit was 9.83 ng.mL-1 and the quantitation limit was 29.80 ng.mL-1. The -caroteneof the four varieties were 465.77-1150.80 mg% (n=3, and of the store samples were 4.70-41.73 mg% (n=3. The resultsdemonstrated that the contents varied according to the variety. The contents in the samples obtained from traditionaldrug stores were much lower that those dried in our laboratory, this might due to the source of the stamens, duration, andconditions of storages.

Print advertising: vivid content

NARCIS (Netherlands)

Fennis, B.M.; Das, E.; Fransen, M.L.

2012-01-01

The present research examines the effects of vivid ad content in two types of appeal in print ads as a function of individual differences in chronically experienced vividness of visual imagery. For informational ads for a functional product, vivid ad content strongly affected individuals high in

Print advertising : Vivid content

NARCIS (Netherlands)

Fennis, B.M.; Das, E.H.H.J.; Fransen, M.L.

The present research examines the effects of vivid ad content in two types of appeal in print ads as a function of individual differences in chronically experienced vividness of visual imagery. For informational ads for a functional product, vivid ad content strongly affected individuals high in

Development of a quantitative morphological assessment of toxicant-treated zebrafish larvae using brightfield imaging and high-content analysis.

Science.gov (United States)

Deal, Samantha; Wambaugh, John; Judson, Richard; Mosher, Shad; Radio, Nick; Houck, Keith; Padilla, Stephanie

2016-09-01

One of the rate-limiting procedures in a developmental zebrafish screen is the morphological assessment of each larva. Most researchers opt for a time-consuming, structured visual assessment by trained human observer(s). The present studies were designed to develop a more objective, accurate and rapid method for screening zebrafish for dysmorphology. Instead of the very detailed human assessment, we have developed the computational malformation index, which combines the use of high-content imaging with a very brief human visual assessment. Each larva was quickly assessed by a human observer (basic visual assessment), killed, fixed and assessed for dysmorphology with the Zebratox V4 BioApplication using the Cellomics® ArrayScan® V(TI) high-content image analysis platform. The basic visual assessment adds in-life parameters, and the high-content analysis assesses each individual larva for various features (total area, width, spine length, head-tail length, length-width ratio, perimeter-area ratio). In developing the computational malformation index, a training set of hundreds of embryos treated with hundreds of chemicals were visually assessed using the basic or detailed method. In the second phase, we assessed both the stability of these high-content measurements and its performance using a test set of zebrafish treated with a dose range of two reference chemicals (trans-retinoic acid or cadmium). We found the measures were stable for at least 1 week and comparison of these automated measures to detailed visual inspection of the larvae showed excellent congruence. Our computational malformation index provides an objective manner for rapid phenotypic brightfield assessment of individual larva in a developmental zebrafish assay. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Efficiency of phosphate fertilization to maize crop in high phosphorus content soil, evaluated by {sup 32}P tracer

Energy Technology Data Exchange (ETDEWEB)

Trevizam, Anderson R.; Alvarez Villanueva, Felipe C.; Silva, Maria Ligia de S.; Muraoka, Takashi [Centro de Energia Nuclear na Agricultura (CENA), Piracicaba, SP (Brazil). Lab. de Fertilidade do Solo]. E-mails: trevizam@cena.usp.br; falvarez@cena.usp.br; mlsousi@hotmail.com; muraoka@cena.usp.br

2007-07-01

Application of high dosis of phosphorus (P) in agricultural soils is justified by its intense fixation by the soil clays, which reduce availability to crops. The objective of this research was to evaluate the response of maize crops to five rates of triple superphosphate in a soil with high available phosphorus content. Portions of 2 dm{sup 3} of soil (Typic Quartzipisamment) with 75 mg kg{sup -1} of available phosphorus and pH 7.00, collected from the upper 0-20 cm layer, were placed in plastic pots, received solution containing 5.55 MBq (150 {mu}Ci) of {sup 32}P and incubated for 7 days. Then 0, 250, 500, 1000 and 4000 mg P kg{sup -1} as triple superphosphate was added to soil in the respective pots and incubated for 15 days keeping the soil moisture to 60 % of the field capacity. Maize (Zea mays L.) plants, single hybrid P30F80, were grown for 50 days (after germination), collected, oven dried, weighed and ground in a Wiley mill for analysis of total P content and {sup 32}P radioactivity. The maize dry matter increased with triple superphosphate rates. The phosphorus content and accumulation in the maize plants increased with triple superphosphate rate up to 4000 mg kg{sup -1}. The percentage of phosphorus derived from the fertilizer ranged from 79 to 97% and consequently the phosphorus derived from soil decreased with increasing application of triple superphosphate. In spite of soil high P available content, maize plants responded to applied phosphorus rates. (author)

Effect of high frequency content of uniform hazard response spectra on nuclear power plant structures, systems and components

Energy Technology Data Exchange (ETDEWEB)

Usmani, A. [Amec Foster Wheeler, Toronto, ON (Canada); Baughman, P.D. [Paul D. Baughman Consulting, Exeter, NH (United States)

2015-07-01

The Uniform Hazard Spectrum (UHS) is developed from a probabilistic seismic hazard assessment and represents a response spectrum for which the amplitude at each frequency has a specified and uniform (equal) probability of exceedance. The high spectral acceleration at high frequencies in the UHS can result mainly from small non-damaging low energy earthquakes. Historically Canadian and U.S. nuclear power plants have been designed using the standard shape spectrum given in CSA N289.3 or USNRC Regulatory Guide 1.60, which have maximum spectral accelerations in the lower (2-10 Hz.) frequency range. The impact of the high frequency content of UHS on the nuclear power plant SSCs is required to be assessed. This paper briefly describes the methodologies used for screening and evaluation of the effects of UHS high frequency content on the nuclear power SSCs that have been designed using the CSA N289.3 standard shape spectrum. (author)

Development and Application of High-Content Biological Screening for Modulators of NET Production

Directory of Open Access Journals (Sweden)

Ilaria J. Chicca

2018-03-01

Full Text Available Neutrophil extracellular traps (NETs are DNA-based antimicrobial web-like structures whose release is predominantly mediated by reactive oxygen species (ROS; their purpose is to combat infections. However, unbalanced NET production and clearance is involved in tissue injury, circulation of auto-antibodies and development of several chronic diseases. Currently, there is lack of agreement regarding the high-throughput methods available for NET investigation. This study, therefore, aimed to develop and optimize a high-content analysis (HCA approach, which can be applied for the assay of NET production and for the screening of compounds involved in the modulation of NET release. A suitable paraformaldehyde fixation protocol was established to enable HCA of neutrophils and NETs. Bespoke and in-built bioinformatics algorithms were validated by comparison with standard low-throughput approaches for application in HCA of NETs. Subsequently, the optimized protocol was applied to high-content screening (HCS of a pharmaceutically derived compound library to identify modulators of NETosis. Of 56 compounds assessed, 8 were identified from HCS for further characterization of their effects on NET formation as being either inducers, inhibitors or biphasic modulators. The effects of these compounds on naïve neutrophils were evaluated by using specific assays for the induction of ROS and NET production, while their modulatory activity was validated in phorbol 12-myristate 13-acetate-stimulated neutrophils. Results indicated the involvement of glutathione reductase, Src family kinases, molecular-target-of-Rapamycin, and mitogen-activated-protein-kinase pathways in NET release. The compounds and pathways identified may provide targets for novel therapeutic approaches for treating NET-associated pathologies.

A pre-Paleogene unconformity surface of the Sikeshu Sag, Junggar Basin: Lithological, geophysical and geochemical implications for the transportation of hydrocarbons

Directory of Open Access Journals (Sweden)

Xiaoyue Gao

2013-11-01

Full Text Available The unconformity surface at the bottom of the Paleogene is one of the most important migration pathways in the Sikeshu Sag of the Junggar Basin, which consists of three layers: upper coarse clastic rock, lower weathering crust and leached zone. The upper coarse clastic rock is characterized by higher density and lower SDT and gamma-ray logging parameters, while the lower weathering crust displays opposite features. The transport coefficient of the unconformity surface is controlled by its position in respect to the basal sandstone; it is higher in the ramp region but lower in the adjacent uplifted and sag areas. The content of saturated hydrocarbons increases with the decrease of the content of non-hydrocarbons and asphaltenes. The content of benzo[c] carbazole decreases as the content of benzo[a] carbazole and [alkyl carbazole]/[alkyl + benzo carbazole] increases. This suggests that the unconformity surface is an efficient medium for the transportation of hydrocarbons.

High-Content Electrophysiological Analysis of Human Pluripotent Stem Cell-Derived Cardiomyocytes (hPSC-CMs).

Science.gov (United States)

Kong, Chi-Wing; Geng, Lin; Li, Ronald A

2018-01-01

Considerable interest has been raised to develop human pluripotent stem cell-derived cardiomyocytes (hPSC-CMs) as a model for drug discovery and cardiotoxicity screening. High-content electrophysiological analysis of currents generated by transmembrane cell surface ion channels has been pursued to complement such emerging applications. Here we describe practical procedures and considerations for accomplishing successful assays of hPSC-CMs using an automated planar patch-clamp system.

Biotreatment of hydrocarbons from petroleum tank bottom sludges in soil slurries

International Nuclear Information System (INIS)

Ferrari, M.D.; Neirotti, E.; Albornoz, C.; Mostazo, M.R.; Cozzo, M.

1996-01-01

Biotreatment of oil wastes in aqueous slurries prepared with sandy loam soil and inoculated with selected soil cultures was evaluated. After 90 days, oil removal was 47%. Removal of each hydrocarbon class was 84% for saturates, 20% for aromatics, and 44% for asphaltenes. Resins increased by 68%. The use of a soil with a lower level of fine particles or minor organic matter content, or reinoculation with fresh culture did not improve oil elimination. Residual oil recovered from slurries was biotreated. Oil removal was 22%. Slurry-phase biotreatment showed less variability and faster oil removal than solid-phase biotreatment. (author)

Age dependency of myocardial triglyceride content. A 3T high-field 1H-MR spectroscopy study

International Nuclear Information System (INIS)

Petritsch, B.; Gassenmaier, T.; Kunz, A.S.; Donhauser, J.; Bley, T.A.; Horn, M.; Goltz, J.P.

2015-01-01

The role of myocardial triglyceride (mTG) content in the aging human heart is not entirely understood. The aim of this study was to measure concentrations of mTG content from healthy volunteers and to determine the association between age, mTG content and systolic heart function. Furthermore, the technical stability of the 1 H-magnetic resonance spectroscopy ( 1 H-MRS) and the reliability of peak evaluation at 3 T were evaluated. The total study population of 47 healthy volunteers was divided into 4 age classes, according to the age of the subjects (1 st cohort 20-29 years (yrs.), n=20; 2 nd cohort 30-39 yrs., n=10; 3 rd cohort 40-49 yrs., n=9; 4 th cohort 50-60 yrs., n=8). Cardiac MRI and double triggered 1 H-MRS of the myocardium were consecutively performed using a 3 T scanner. Each participant underwent spectroscopic measurements twice in the same investigation. mTG content increases with age. The correlation of age and mTG is minimal (r=0.48; p<0.001). The following age-averaged mTG content values expressed as % of mTG signal compared to the water signal were determined for each cohort: 1 st cohort 0.25 % (± 0.17); 2 nd cohort 0.48 % (± 0.30); 3 rd cohort 0.48 % (± 0.18); 4 th cohort 0.77 % (± 0.70). There was no significant correlation (r=0.04; p=n.s.) between LV mass and mTG content in healthy volunteers. Within our cohorts, no effects of age or mTG content on systolic heart function were seen (r=-0.01; p=n.s.). The intraclass correlation coefficient of spectroscopic measurements was high (r=0.965; p<0.001). Myocardial TG content increases with age. The normal age-dependent concentration ranges of myocardial lipid metabolites reported in this study may be helpful for the correction of acquired 1 H-MRS data in patients when evaluating metabolic and cardiovascular diseases in future magnetic resonance spectroscopy studies.

HC StratoMineR: A web-based tool for the rapid analysis of high content datasets

NARCIS (Netherlands)

Omta, W.; Heesbeen, R. van; Pagliero, R.; Velden, L. van der; Lelieveld, D.; Nellen, M.; Kramer, M.; Yeong, M.; Saeidi, A.; Medema, R.; Spruit, M.; Brinkkemper, S.; Klumperman, J.; Egan, D.

2016-01-01

High-content screening (HCS) can generate large multidimensional datasets and when aligned with the appropriate data mining tools, it can yield valuable insights into the mechanism of action of bioactive molecules. However, easy-to-use data mining tools are not widely available, with the result that

HC StratoMineR : A Web-Based Tool for the Rapid Analysis of High-Content Datasets

NARCIS (Netherlands)

Omta, Wienand A; van Heesbeen, Roy G; Pagliero, Romina J; van der Velden, Lieke M; Lelieveld, Daphne; Nellen, Mehdi; Kramer, Maik; Yeong, Marley; Saeidi, Amir M; Medema, Rene H; Spruit, Marco; Brinkkemper, Sjaak; Klumperman, Judith; Egan, David A

2016-01-01

High-content screening (HCS) can generate large multidimensional datasets and when aligned with the appropriate data mining tools, it can yield valuable insights into the mechanism of action of bioactive molecules. However, easy-to-use data mining tools are not widely available, with the result that

Determining Total Phenolics, Anthocyanin Content and Ascorbic Acid Content in Some Plum Genotypes Grown in Ardahan Ecological Conditions

Directory of Open Access Journals (Sweden)

Z. T. ABACI

2014-06-01

Full Text Available In this study, total phenol content, total anthocyanin content, brix, pH, titrable acidity and total ascorbic acid content in the five plum genotypes cultivated in Ardahan City are determined and sustenance of the plums are revealed. Total phenol content was determined with folin-ciocalteu’s method, total anthocyanin content was determined with pH differential method and total ascorbic acid was determined with 2,6-dichlorophenolindophenol method.It is detected that the genotype with the highest brix content (%13.9 and lowest acidity (%0.98 is cancur, the genotype with the lowest brix content (%11 and highest acidity (%2.06 is wild plum, the genotype with the highest content of total anthocyanin, total phenolic substance and ascorbic acid is the wild plum and the genotype with the least content of these is the water plum. As a result of the study, it is revealed that the plum fruit has high levels of phenolic substance, anthocyanin and ascorbic acid content, so it has a high sustenance.

G protein-coupled receptor internalization assays in the high-content screening format.

Science.gov (United States)

Haasen, Dorothea; Schnapp, Andreas; Valler, Martin J; Heilker, Ralf

2006-01-01

High-content screening (HCS), a combination of fluorescence microscopic imaging and automated image analysis, has become a frequently applied tool to study test compound effects in cellular disease-modeling systems. This chapter describes the measurement of G protein-coupled receptor (GPCR) internalization in the HCS format using a high-throughput, confocal cellular imaging device. GPCRs are the most successful group of therapeutic targets on the pharmaceutical market. Accordingly, the search for compounds that interfere with GPCR function in a specific and selective way is a major focus of the pharmaceutical industry today. This chapter describes methods for the ligand-induced internalization of GPCRs labeled previously with either a fluorophore-conjugated ligand or an antibody directed against an N-terminal tag of the GPCR. Both labeling techniques produce robust assay formats. Complementary to other functional GPCR drug discovery assays, internalization assays enable a pharmacological analysis of test compounds. We conclude that GPCR internalization assays represent a valuable medium/high-throughput screening format to determine the cellular activity of GPCR ligands.

Inorganic/organic nanocomposites: Reaching a high filler content without increasing viscosity using core-shell structured nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Benhadjala, W., E-mail: warda.benhadjala@cea.fr [IMS Laboratory - UMR CNRS 5218, University of Bordeaux, 351 Cours de la Libération, 33405 Talence (France); CEA, LETI, Minatec Campus, 38000 Grenoble (France); Gravoueille, M.; Weiss, M. [EDF, Centre d' Expertise et d' Inspection dans les Domaines de la Réalisation et de l' Exploitation (CEIDRE), Chinon, BP 80, 37420 Avoine (France); Bord-Majek, I.; Béchou, L.; Ousten, Y. [IMS Laboratory - UMR CNRS 5218, University of Bordeaux, 351 Cours de la Libération, 33405 Talence (France); Suhir, E. [Maseeh College of Engineering and Computer Science, Portland State University, Oregon 97201 (United States); Buet, M.; Louarn, M.; Rougé, F.; Gaud, V. [Polyrise SAS, 16 Avenue Pey Berland, 33607 Pessac (France)

2015-11-23

Extensive research is being conducted on the development of inorganic/organic nanocomposites for a wide variety of applications in microelectronics, biotechnologies, photonics, adhesives, or optical coatings. High filler contents are usually required to fully optimize the nanocomposites properties. However, numerous studies demonstrated that traditional composite viscosity increases with increasing the filler concentration reducing therefore significantly the material processability. In this work, we synthesized inorganic/organic core-shell nanocomposites with different shell thicknesses. By reducing the shell thickness while maintaining a constant core size, the nanoparticle molecular mass decreases but the nanocomposite filler fraction is correlatively increased. We performed viscosity measurements, which clearly highlighted that intrinsic viscosity of hybrid nanoparticles decreases as the molecular mass decreases, and thus, as the filler fraction increases, as opposed to Einstein predictions about the viscosity of traditional inorganic/polymer two-phase mixtures. This exceptional behavior, modeled by Mark-Houwink-Sakurada equation, proves to be a significant breakthrough for the development of industrializable nanocomposites with high filler contents.

High-efficient and high-content cytotoxic recording via dynamic and continuous cell-based impedance biosensor technology.

Science.gov (United States)

Hu, Ning; Fang, Jiaru; Zou, Ling; Wan, Hao; Pan, Yuxiang; Su, Kaiqi; Zhang, Xi; Wang, Ping

2016-10-01

Cell-based bioassays were effective method to assess the compound toxicity by cell viability, and the traditional label-based methods missed much information of cell growth due to endpoint detection, while the higher throughputs were demanded to obtain dynamic information. Cell-based biosensor methods can dynamically and continuously monitor with cell viability, however, the dynamic information was often ignored or seldom utilized in the toxin and drug assessment. Here, we reported a high-efficient and high-content cytotoxic recording method via dynamic and continuous cell-based impedance biosensor technology. The dynamic cell viability, inhibition ratio and growth rate were derived from the dynamic response curves from the cell-based impedance biosensor. The results showed that the biosensors has the dose-dependent manners to diarrhetic shellfish toxin, okadiac acid based on the analysis of the dynamic cell viability and cell growth status. Moreover, the throughputs of dynamic cytotoxicity were compared between cell-based biosensor methods and label-based endpoint methods. This cell-based impedance biosensor can provide a flexible, cost and label-efficient platform of cell viability assessment in the shellfish toxin screening fields.

Teachable, high-content analytics for live-cell, phase contrast movies.

Science.gov (United States)

Alworth, Samuel V; Watanabe, Hirotada; Lee, James S J

2010-09-01

CL-Quant is a new solution platform for broad, high-content, live-cell image analysis. Powered by novel machine learning technologies and teach-by-example interfaces, CL-Quant provides a platform for the rapid development and application of scalable, high-performance, and fully automated analytics for a broad range of live-cell microscopy imaging applications, including label-free phase contrast imaging. The authors used CL-Quant to teach off-the-shelf universal analytics, called standard recipes, for cell proliferation, wound healing, cell counting, and cell motility assays using phase contrast movies collected on the BioStation CT and BioStation IM platforms. Similar to application modules, standard recipes are intended to work robustly across a wide range of imaging conditions without requiring customization by the end user. The authors validated the performance of the standard recipes by comparing their performance with truth created manually, or by custom analytics optimized for each individual movie (and therefore yielding the best possible result for the image), and validated by independent review. The validation data show that the standard recipes' performance is comparable with the validated truth with low variation. The data validate that the CL-Quant standard recipes can provide robust results without customization for live-cell assays in broad cell types and laboratory settings.

Radon exhalation rate and natural radionuclide content in building materials of high background areas of Ramsar, Iran

International Nuclear Information System (INIS)

Bavarnegin, E.; Fathabadi, N.; Vahabi Moghaddam, M.; Vasheghani Farahani, M.; Moradi, M.; Babakhni, A.

2013-01-01

Radon exhalation rates from building materials used in high background radiation areas (HBRA) of Ramsar were measured using an active radon gas analyzer with an emanation container. Radon exhalation rates from these samples varied from below the lower detection limit up to 384 Bq.m −2 h −1 . The 226 Ra, 232 Th and 40 K contents were also measured using a high resolution HPGe gamma- ray spectrometer system. The activity concentration of 226 Ra, 232 Th and 40 K content varied from below the minimum detection limit up to 86,400 Bq kg −1 , 187 Bq kg −1 and 1350 Bq kg −1 , respectively. The linear correlation coefficient between radon exhalation rate and radium concentration was 0.90. The result of this survey shows that radon exhalation rate and radium content in some local stones used as basements are extremely high and these samples are main sources of indoor radon emanation as well as external gamma radiation from uranium series. -- Highlights: ► In the selection process of local samples, portable scintillometer (NaI) was used. ► The activity concentration of 226 Ra varied from below the MDL up to 86400 Bq kg −1 . ► The activity concentration of 232 Th varied from below the MDL up to 187 Bq kg −1 . ► The activity concentration of 40 K varied from below the MDL up to 1350 Bq kg −1

BioSig3D: High Content Screening of Three-Dimensional Cell Culture Models.

Directory of Open Access Journals (Sweden)

Cemal Cagatay Bilgin

Full Text Available BioSig3D is a computational platform for high-content screening of three-dimensional (3D cell culture models that are imaged in full 3D volume. It provides an end-to-end solution for designing high content screening assays, based on colony organization that is derived from segmentation of nuclei in each colony. BioSig3D also enables visualization of raw and processed 3D volumetric data for quality control, and integrates advanced bioinformatics analysis. The system consists of multiple computational and annotation modules that are coupled together with a strong use of controlled vocabularies to reduce ambiguities between different users. It is a web-based system that allows users to: design an experiment by defining experimental variables, upload a large set of volumetric images into the system, analyze and visualize the dataset, and either display computed indices as a heatmap, or phenotypic subtypes for heterogeneity analysis, or download computed indices for statistical analysis or integrative biology. BioSig3D has been used to profile baseline colony formations with two experiments: (i morphogenesis of a panel of human mammary epithelial cell lines (HMEC, and (ii heterogeneity in colony formation using an immortalized non-transformed cell line. These experiments reveal intrinsic growth properties of well-characterized cell lines that are routinely used for biological studies. BioSig3D is being released with seed datasets and video-based documentation.

Analysis of Levodopa Content in Commercial Mucuna pruriens Products Using High-Performance Liquid Chromatography with Fluorescence Detection.

Science.gov (United States)

Soumyanath, Amala; Denne, Tanya; Hiller, Amie; Ramachandran, Shaila; Shinto, Lynne

2018-02-01

Mucuna pruriens (MP) seeds contain levodopa (up to 2% by weight) and have been used in traditional Indian medicine to treat an illness named "Kampavata," now understood to be Parkinson's disease (PD). Studies have shown MP to be beneficial, and even superior, to levodopa alone in treating PD symptoms. Commercial products containing MP are readily available from online and retail sources to patients and physicians. Products often contain extracts of MP seeds, with significantly higher levodopa content than the seeds. However, MP products have limited regulatory controls with respect to quality and content of active ingredient. The aim of this study was to apply a quantitative method to determine levodopa content in readily available MP products that might be used by patients or in research studies. Levodopa present in six commercial MP products was quantified by solvent extraction followed by reversed-phase high-performance liquid chromatography (HPLC) coupled to fluorescence detection (FD). Certificates of analysis (COA) were obtained, from manufacturers of MP products, to assess the existence and implementation of specifications for levodopa content. HPLC-FD analysis revealed that the levodopa content of the six commercial MP products varied from 6% to 141% of individual label claims. No product contained levodopa within normal pharmacopeial limits of 90%-110% label claim. The maximum daily dose of levodopa delivered by the products varied from 14.4 to 720 mg/day. COAs were inconsistent in specifications for and verification of levodopa content. The commercial products tested varied widely in levodopa content, sometimes deviating widely from the label claim. These deficiencies could impact efficacy and safety of MP products used by PD patients and compromise the results of scientific studies on MP products. The HPLC-FD method described in this study could be utilized by both manufacturers and scientific researchers to verify levodopa content of MP products.

Robust, Reliable Low Emission Gas Turbine Combustion of High Hydrogen Content Fuels

Energy Technology Data Exchange (ETDEWEB)

Wooldridge, Margaret Stacy [Univ. of Michigan, Ann Arbor, MI (United States); Im, Hong Geum [Univ. of Michigan, Ann Arbor, MI (United States)

2016-12-16

The effects of high hydrogen content fuels were studied using experimental, computational and theoretical approaches to understand the effects of mixture and state conditions on the ignition behavior of the fuels. A rapid compression facility (RCF) was used to measure the ignition delay time of hydrogen and carbon monoxide mixtures. The data were combined with results of previous studies to develop ignition regime criteria. Analytical theory and direct numerical simulation were used to validate and interpret the RCF ignition data. Based on the integrated information the ignition regime criteria were extended to non-dimensional metrics which enable application of the results to practical gas turbine combustion systems.

Effects of low calcium plus high aluminum diet on magnesium and calcium contents in spinal cord and trabecular bone of rats

Energy Technology Data Exchange (ETDEWEB)

Yasui, Masayuki; Ota, Kiichiro [Wakayama Medical Coll. (Japan); Sasajima, Kazuhisa

1998-01-01

Current epidemiological surveys in the Western Pacific area and Kii Peninsula have suggested that low calcium (Ca), magnesium (Mg), and high aluminum (Al) and manganese (Mn) in river, soil and drinking water may be implicated in the pathogenetic process of amyotrophic lateral sclerosis (ALS) and parkinsonism-dementia (PD). The condition of unbalanced minerals was experimentally duplicated in this study using rats. Male Wistar rats, weighing 200 g, were maintained for 60 days on the following diets: (A) standard diet, (B) low Ca diet, (C) low Ca diet with high Al. Magnesium concentration was determined in spinal cord and trabecular bone using inductively coupled plasma emission spectrometry (ICP) and the calcium concentration was determined using neutron activation method. In the group maintained on low Ca high Al diet, magnesium content of the spinal cord was lower than the group fed standard diet. Also, magnesium content of lumbar bone showed lower values in the unbalanced diet group fed low Ca high Al diet than those in the standard diet and low Ca diet groups. Calcium content of spinal cord was highest in rats maintained on low Ca high Al diet. Calcium content in lumbar bone of rats significantly decreased in rats maintained on the low Ca diet (group B and C) compared to rats given a standard diet (group A). Our data indicate that low Ca and high Al dietary intake influence Mg concentration in bone and central nervous system (CNS) tissues and that low Ca and high Al diet diminish Mg in bone and CNS tissues, thereby inducing loss of calcification in bone and degeneration of CNS tissues due to disturbance of the normal biological effects of Mg. (author)

The Content of Literature in the High School.

Science.gov (United States)

Burton, Dwight L.

The content of a literature program defined in terms of the structure of literature is proposed. A three-layer definition of structure is suggested which considers (1) the substance of literature, including man and his gods, man and the natural world, man and other men, and man and himself; (2) mode in literature, including the romantic, comic,…

Development of a chromatographic method for the study of the stability and compatibility of Mexican fuel oils; Desarrollo de un metodo cromatografico para el estudio de estabilidad y compatibilidad de combustoleos mexicanos

Energy Technology Data Exchange (ETDEWEB)

Blass Amador, Georgina; Panama Tirado, Luz Angelica [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1992-11-01

In Mexico, the largest part of the generated electric energy comes from the use of residual heavy oils known as fuel oils which have suffered quality degradation due to a combination of factors, among which stands out the changes in the refining process. It is necessary to develop methods capable of indicating the instability (formation of sediment or viscosity increase during storage or heating) or incompatibility (formation of sediment in mixing two or more fuel oils) of the fuel oils employed in fossil fuel power plants. This work objective was to develop an alternative test for the study of the compatibility and/or stability of Mexican fuel oils using high resolution liquid chromatography (CLAR) and so to determine structural aspects of the fuel oil that determine its stability. Since the formation of sediments occurs when the dissolving ability of the fuel is inadequate to keep the asphaltenes in solution, it is important to know the solvent power degree or aromaticity of the diluent; so, in the first part of this work the attention was centered in the determination of the profile of aromatic compounds of the fuel oil diluents, the other part was dedicated to the determination of the distribution profile the molecular weights of the asphaltenes present in the fuel oils. The profiles of the aromatic fraction, as well as of the molecular weight distribution were determined using liquid chromatography, in which a variety of columns and solvents were used. A combination of routine tests was accomplished, such as asphaltenes content, toluene equivalence, viscosity, etc., in order to obtain correlation with the chromatographic method developed. In this article it is only discussed the section corresponding to the obtainment of the profile of aromatics content in the fuel oils. It has been found a correlation among the asphaltenes content, toluene equivalence, aromaticity profiles and stability. As a direct consequence, it is expected to be able to predict the

Variations in pore characteristics in high volatile bituminous coals: Implications for coal bed gas content

Science.gov (United States)

Mastalerz, Maria; Drobniak, A.; Strapoc, D.; Solano-Acosta, W.; Rupp, J.

2008-01-01

The Seelyville Coal Member of the Linton Formation (Pennsylvanian) in Indiana was studied to: 1) understand variations in pore characteristics within a coal seam at a single location and compare these variations with changes occurring between the same coal at different locations, 2) elaborate on the influence of mineral-matter and maceral composition on mesopore and micropore characteristics, and 3) discuss implications of these variations for coal bed gas content. The coal is high volatile bituminous rank with R0 ranging from 0.57% to 0.60%. BET specific surface areas (determined by nitrogen adsorption) of the coals samples studied range from 1.8 to 22.9??m2/g, BJH adsorption mesopore volumes from 0.0041 to 0.0339??cm3/g, and micropore volumes (determined by carbon dioxide adsorption) from 0.0315 to 0.0540??cm3/g. The coals that had the largest specific surface areas and largest mesopore volumes occur at the shallowest depths, whereas the smallest values for these two parameters occur in the deepest coals. Micropore volumes, in contrast, are not depth-dependent. In the coal samples examined for this study, mineral-matter content influenced both specific surface area as well as mesopore and micropore volumes. It is especially clear in the case of micropores, where an increase in mineral-matter content parallels the decrease of micropore volume of the coal. No obvious relationships were observed between the total vitrinite content and pore characteristics but, after splitting vitrinite into individual macerals, we see that collotelinite influences both meso- and micropore volume positively, whereas collodetrinite contributes to the reduction of mesopore and micropore volumes. There are large variations in gas content within a single coal at a single location. Because of this variability, the entire thickness of the coal must be desorbed in order to determine gas content reliably and to accurately calculate the level of gas saturation. ?? 2008 Elsevier B.V. All

Pedagogical Content Knowledge of Argumentation: Using Classroom Contexts to Assess High-Quality PCK Rather than Pseudoargumentation

Science.gov (United States)

McNeill, Katherine L.; González-Howard, María; Katsh-Singer, Rebecca; Loper, Suzanna

2016-01-01

Despite the recent emphasis on science practices, little work has focused on teachers' knowledge of these key learning goals. The development of high quality assessments for teachers' pedagogical content knowledge (PCK) of science practices, such as argumentation, is important to better assess the needs of teachers and to develop supportive…

A high content, high throughput cellular thermal stability assay for measuring drug-target engagement in living cells.

Science.gov (United States)

Massey, Andrew J

2018-01-01

Determining and understanding drug target engagement is critical for drug discovery. This can be challenging within living cells as selective readouts are often unavailable. Here we describe a novel method for measuring target engagement in living cells based on the principle of altered protein thermal stabilization / destabilization in response to ligand binding. This assay (HCIF-CETSA) utilizes high content, high throughput single cell immunofluorescent detection to determine target protein levels following heating of adherent cells in a 96 well plate format. We have used target engagement of Chk1 by potent small molecule inhibitors to validate the assay. Target engagement measured by this method was subsequently compared to target engagement measured by two alternative methods (autophosphorylation and CETSA). The HCIF-CETSA method appeared robust and a good correlation in target engagement measured by this method and CETSA for the selective Chk1 inhibitor V158411 was observed. However, these EC50 values were 23- and 12-fold greater than the autophosphorylation IC50. The described method is therefore a valuable advance in the CETSA method allowing the high throughput determination of target engagement in adherent cells.

Error Analysis of Clay-Rock Water Content Estimation with Broadband High-Frequency Electromagnetic Sensors—Air Gap Effect

Science.gov (United States)

Bore, Thierry; Wagner, Norman; Delepine Lesoille, Sylvie; Taillade, Frederic; Six, Gonzague; Daout, Franck; Placko, Dominique

2016-01-01

Broadband electromagnetic frequency or time domain sensor techniques present high potential for quantitative water content monitoring in porous media. Prior to in situ application, the impact of the relationship between the broadband electromagnetic properties of the porous material (clay-rock) and the water content on the frequency or time domain sensor response is required. For this purpose, dielectric properties of intact clay rock samples experimental determined in the frequency range from 1 MHz to 10 GHz were used as input data in 3-D numerical frequency domain finite element field calculations to model the one port broadband frequency or time domain transfer function for a three rods based sensor embedded in the clay-rock. The sensor response in terms of the reflection factor was analyzed in time domain with classical travel time analysis in combination with an empirical model according to Topp equation, as well as the theoretical Lichtenecker and Rother model (LRM) to estimate the volumetric water content. The mixture equation considering the appropriate porosity of the investigated material provide a practical and efficient approach for water content estimation based on classical travel time analysis with the onset-method. The inflection method is not recommended for water content estimation in electrical dispersive and absorptive material. Moreover, the results clearly indicate that effects due to coupling of the sensor to the material cannot be neglected. Coupling problems caused by an air gap lead to dramatic effects on water content estimation, even for submillimeter gaps. Thus, the quantitative determination of the in situ water content requires careful sensor installation in order to reach a perfect probe clay rock coupling. PMID:27096865

Error Analysis of Clay-Rock Water Content Estimation with Broadband High-Frequency Electromagnetic Sensors—Air Gap Effect

Directory of Open Access Journals (Sweden)

Thierry Bore

2016-04-01

Full Text Available Broadband electromagnetic frequency or time domain sensor techniques present high potential for quantitative water content monitoring in porous media. Prior to in situ application, the impact of the relationship between the broadband electromagnetic properties of the porous material (clay-rock and the water content on the frequency or time domain sensor response is required. For this purpose, dielectric properties of intact clay rock samples experimental determined in the frequency range from 1 MHz to 10 GHz were used as input data in 3-D numerical frequency domain finite element field calculations to model the one port broadband frequency or time domain transfer function for a three rods based sensor embedded in the clay-rock. The sensor response in terms of the reflection factor was analyzed in time domain with classical travel time analysis in combination with an empirical model according to Topp equation, as well as the theoretical Lichtenecker and Rother model (LRM to estimate the volumetric water content. The mixture equation considering the appropriate porosity of the investigated material provide a practical and efficient approach for water content estimation based on classical travel time analysis with the onset-method. The inflection method is not recommended for water content estimation in electrical dispersive and absorptive material. Moreover, the results clearly indicate that effects due to coupling of the sensor to the material cannot be neglected. Coupling problems caused by an air gap lead to dramatic effects on water content estimation, even for submillimeter gaps. Thus, the quantitative determination of the in situ water content requires careful sensor installation in order to reach a perfect probe clay rock coupling.

Error Analysis of Clay-Rock Water Content Estimation with Broadband High-Frequency Electromagnetic Sensors--Air Gap Effect.

Science.gov (United States)

Bore, Thierry; Wagner, Norman; Lesoille, Sylvie Delepine; Taillade, Frederic; Six, Gonzague; Daout, Franck; Placko, Dominique

2016-04-18

Broadband electromagnetic frequency or time domain sensor techniques present high potential for quantitative water content monitoring in porous media. Prior to in situ application, the impact of the relationship between the broadband electromagnetic properties of the porous material (clay-rock) and the water content on the frequency or time domain sensor response is required. For this purpose, dielectric properties of intact clay rock samples experimental determined in the frequency range from 1 MHz to 10 GHz were used as input data in 3-D numerical frequency domain finite element field calculations to model the one port broadband frequency or time domain transfer function for a three rods based sensor embedded in the clay-rock. The sensor response in terms of the reflection factor was analyzed in time domain with classical travel time analysis in combination with an empirical model according to Topp equation, as well as the theoretical Lichtenecker and Rother model (LRM) to estimate the volumetric water content. The mixture equation considering the appropriate porosity of the investigated material provide a practical and efficient approach for water content estimation based on classical travel time analysis with the onset-method. The inflection method is not recommended for water content estimation in electrical dispersive and absorptive material. Moreover, the results clearly indicate that effects due to coupling of the sensor to the material cannot be neglected. Coupling problems caused by an air gap lead to dramatic effects on water content estimation, even for submillimeter gaps. Thus, the quantitative determination of the in situ water content requires careful sensor installation in order to reach a perfect probe clay rock coupling.

New formulations of sunflower based bio-lubricants with high oleic acid content – VOSOLUB project

Directory of Open Access Journals (Sweden)

Leao J. D.

2016-09-01

Full Text Available VOSOLUB project is a demonstration project supported by Executive Agency for Small and Medium-sized Enterprises (EASME that aims at testing under real operating conditions new formulations of sunflower-based biolubricants with high oleic acid content. These biolubricant formulations (including hydraulic fluids, greases, and neat oil metal-working fluids will be tested in three European demonstrating sites. Their technical performance will be evaluated and compared to corresponding mineral lubricants ones. In order to cover the demand for the sunflower base oil, a European SMEs network will be established to ensure the supply of the base at a competitive market price. Results presented concerns the base oil quality confirmed to be in accordance with the specification required, in particular on Free Fatty acid content, Phosphorus content, rancimat induction time and oleic acid content (ITERG. The oil characteristics specific for lubricant application analyzed by BfB Oil Research under normalized methods, match with lubricant specifications requirement such as viscosity, cold & hot properties, surface properties, anti-oxidant properties and thermal stability, anti-wear and EP properties, anti-corrosion properties Performance of the new biolubricant have been assessed by formulators and TEKNIKER First results on the use of new lubricant on real condition for rail Grease (produced by RS CLARE and tested with Sheffield Supertram, Hydraulic oil (produced by BRUGAROLAS and cutting oil (produced by MOTUL TECH and tested with innovative machining, turning are described.

Corrosion Behavior of the Stressed Sensitized Austenitic Stainless Steels of High Nitrogen Content in Seawater

Directory of Open Access Journals (Sweden)

A. Almubarak

2013-01-01

Full Text Available The purpose of this paper is to study the effect of high nitrogen content on corrosion behavior of austenitic stainless steels in seawater under severe conditions such as tensile stresses and existence of sensitization in the structure. A constant tensile stress has been applied to sensitized specimens types 304, 316L, 304LN, 304NH, and 316NH stainless steels. Microstructure investigation revealed various degrees of stress corrosion cracking. SCC was severe in type 304, moderate in types 316L and 304LN, and very slight in types 304NH and 316NH. The electrochemical polarization curves showed an obvious second current peak for the sensitized alloys which indicated the existence of second phase in the structure and the presence of intergranular stress corrosion cracking. EPR test provided a rapid and efficient nondestructive testing method for showing passivity, degree of sensitization and determining IGSCC for stainless steels in seawater. A significant conclusion was obtained that austenitic stainless steels of high nitrogen content corrode at a much slower rate increase pitting resistance and offer an excellent resistance to stress corrosion cracking in seawater.

Dephosphorization of melts with chromium content

International Nuclear Information System (INIS)

Motloch, Z.

1985-01-01

A survey is given of the results of laboratory and pilot plant research into the dephosphorization of high-chromium melts reported in the literature, mostly Japanese. The use of high-alloy chromium and chromium-nickel steels in nuclear power engineering showed the negative impact of phosphorus on stress corrosion at high temperatures and on the development of cracks under overlays during welding. For a number of years attention is therefore being devoted to the attainment of a low phosphorus content in these steels. Current dephosphorization methods may be divided into oxidation and reduction methods. Oxidation dephosphorization may be carried out using synthetic mixtures: in the use of CaO-FeCl 2 , BaO-BaCl 2 -Cr 2 O 3 , Li 2 CO 3 -CaO-CaF 2 -FeO and Na 2 CO 3 /K 2 CO 3 -NaCl/KCl/KF/CaCl 2 /FeCl 2 a high initial C content, low content of Cr and Si and a low temperature of the melt are advantageous for dephosphorization. Experiments have also been made with dephosphorization in a bottom-blown oxygen converter and in an AOD converter. The most frequently used substances for reduction dephosphorization are calcium and calcium carbide; the best C content ranges between 0.5 and 1.8%, a high Cr content and a high bath temperature are also advantageous. The use of the reduction procedure is greatly limited by the generation of highly toxic phosphine. Another tested method - electroslag remelting is not suitable for commercial application for its economic exactingness. (A.K.)

Combined high-power ultrasound and high-pressure homogenization nanoemulsification: The effect of energy density, oil content and emulsifier type and content.

Science.gov (United States)

Calligaris, Sonia; Plazzotta, Stella; Valoppi, Fabio; Anese, Monica

2018-05-01

Combinations of ultrasound (US) and high-pressure homogenization (HPH) at low-medium energy densities were studied as alternative processes to individual US and HPH to produce Tween 80 and whey protein stabilized nanoemulsions, while reducing the energy input. To this aim, preliminary trials were performed to compare emulsification efficacy of single and combined HPH and US treatments delivering low-medium energy densities. Results highlighted the efficacy of US-HPH combined process in reducing the energy required to produce nanoemulsions stabilized with both Tween 80 and whey protein isolate. Subsequently, the effect of emulsifier content (1-3% w/w), oil amount (10-20% w/w) and energy density (47-175 MJ/m 3 ) on emulsion mean particle diameter was evaluated by means of a central composite design. Particles of 140-190 nm were obtained by delivering 175 MJ/m 3 energy density at emulsions containing 3% (w/w) Tween 80 and 10% (w/w) oil. In the case of whey protein isolate stabilized emulsions, a reduced emulsifier amount (1% w/w) and intermediate energy density (120 MJ/m 3 ) allowed a minimum droplet size around 220-250 nm to be achieved. Results showed that, in both cases, at least 50% of the energy density should be delivered by HPH to obtain the minimum particle diameter. Copyright © 2018 Elsevier Ltd. All rights reserved.

In vivo effects of high-dose steroids on nucleic acid content of immunocompetent cells of renal allograft recipients

International Nuclear Information System (INIS)

Walle, A.J.; Wong, G.Y.; Suthanthiran, M.; Rubin, A.L.; Stenzel, K.H.

1988-01-01

High-dose steroids administered to renal allograft recipients for treatment of acute graft rejection episodes may affect cell cycle progression of peripheral blood mononuclear (PBM) cells. DNA synthesis and cellular DNA and RNA contents of PBM cells were measured in 8 patients during clinically stable periods, and in another 10 patients both during acute rejection episodes and during 7 days of administration of high-dose steroids. Improved renal function documented successful reversal of the rejection episodes in the 10 patients. Compared with the stable patients, the rejecting patients had higher numbers of cells undergoing clonal expansion--namely, higher proportions of G1-cells and of proliferating, or S, G2, and M (SG2M) cells. Steroid treatment had no acute effects on proportions of G1 or SG2M cells in vivo or on incorporation of 3 H thymidine by PBM cells in vitro. However, cells in the prereplicative compartment of the cell cycle (G0/1 cells) had significantly lower RNA content within 7 days of treatment with high doses of steroids. The results suggest that steroids do not acutely influence the posttranscriptional synthesis and the contents of nucleic acids of cells undergoing clonal expansion in vivo. The prereplicative phase of allogeneically stimulated PBM cells of renal allograft recipients may therefore be the cell cycle phase most sensitive to steroids in vivo

Rice and Bean Targets for Biofortification Combined with High Carotenoid Content Crops Regulate Transcriptional Mechanisms Increasing Iron Bioavailability

Directory of Open Access Journals (Sweden)

Desirrê Morais Dias

2015-11-01

Full Text Available Iron deficiency affects thousands of people worldwide. Biofortification of staple food crops aims to support the reduction of this deficiency. This study evaluates the effect of combinations of common beans and rice, targets for biofortification, with high carotenoid content crops on the iron bioavailability, protein gene expression, and antioxidant effect. Iron bioavailability was measured by the depletion/repletion method. Seven groups were tested (n = 7: Pontal bean (PB; rice + Pontal bean (R + BP; Pontal bean + sweet potato (PB + SP; Pontal bean + pumpkin (PB + P; Pontal bean + rice + sweet potato (PB + R + P; Pontal bean + rice + sweet potato (PB + R + SP; positive control (Ferrous Sulfate. The evaluations included: hemoglobin gain, hemoglobin regeneration efficiency (HRE, gene expression of divalente metal transporter 1 (DMT-1, duodenal citocromo B (DcytB, ferroportin, hephaestin, transferrin and ferritin and total plasma antioxidant capacity (TAC. The test groups, except the PB, showed higher HRE (p < 0.05 than the control. Gene expression of DMT-1, DcytB and ferroportin increased (p < 0.05 in the groups fed with high content carotenoid crops (sweet potato or pumpkin. The PB group presented lower (p < 0.05 TAC than the other groups. The combination of rice and common beans, and those with high carotenoid content crops increased protein gene expression, increasing the iron bioavailability and antioxidant capacity.

Design of an assessment to probe teachers' content knowledge for teaching: An example from energy in high school physics

Science.gov (United States)

Etkina, Eugenia; Gitomer, Drew; Iaconangelo, Charles; Phelps, Geoffrey; Seeley, Lane; Vokos, Stamatis

2018-06-01

Research into teacher learning and practice over the last three decades shows that the teachers of a specific subject need to possess knowledge that is different from the knowledge of other content experts. Yet this specialized version of content knowledge that teachers need to plan instruction, respond to student ideas, and assess student understanding in real time is a theoretically elusive construct. It is crucial for the fields of precollege teacher preparation, teacher professional education, and postsecondary faculty professional development to (a) clarify the construct that underlies this specialized content knowledge, (b) operationalize it in some domain, (c) measure it in both static contexts and as it is enacted in the classroom, and (d) correlate its presence with "richness" of classroom instruction and its effect on student learning. This paper documents a piece of a multiyear, multi-institutional effort to investigate points (a)-(d) in the domain of energy in the first high school physics course. In particular, we describe the framework that we developed to clarify content knowledge for teaching in the context of high school energy learning. We then outline the process through which we developed, tested, and refined a "paper-and-pencil" assessment administered on a computer and discuss the substantive and psychometric features of several items based on a field test of the final form of the assessment. We choose to discuss these items for a dual purpose: to illustrate the application of our general framework and to present performance findings from a sample of 362 practicing high school teachers of physics.

Development of Au-Ge based candidate alloys as an alternative to high-lead content solders

DEFF Research Database (Denmark)

Chidambaram, Vivek; Hald, John; Hattel, Jesper Henri

2010-01-01

Au-Ge based candidate alloys have been proposed as an alternative to high-lead content solders that are currently being used for high-temperature applications. The changes in microstructure and microhardness associated with the addition of low melting point metals namely In, Sb and Sn to the Au......-Ge-In and Au-Ge-Sn combinations was determined to be the classic solid solution strengthening. The Au-Ge-Sb combination was primarily strengthened by the refined (Ge) dispersed phase. The aging temperature had a significant influence on the microhardness in the case of the Au-Ge-Sn candidate alloy...

Biocompatible Ni-free Zr-based bulk metallic glasses with high-Zr-content: compositional optimization for potential biomedical applications.

Science.gov (United States)

Hua, Nengbin; Huang, Lu; Chen, Wenzhe; He, Wei; Zhang, Tao

2014-11-01

The present study designs and prepares Ni-free Zr60+xTi2.5Al10Fe12.5-xCu10Ag5 (at.%, x=0, 2.5, 5) bulk metallic glasses (BMGs) by copper mold casting for potential biomedical application. The effects of Zr content on the in vitro biocompatibility of the Zr-based BMGs are evaluated by investigating mechanical properties, bio-corrosion behavior, and cellular responses. It is found that increasing the content of Zr is favorable for the mechanical compatibility with a combination of low Young's modulus, large plasticity, and high notch toughness. Electrochemical measurements demonstrate that the Zr-based BMGs are corrosion resistant in a phosphate buffered saline solution. The bio-corrosion resistance of BMGs is improved with the increase in Zr content, which is attributed to the enrichment in Zr and decrease in Al concentration in the surface passive film of alloys. Regular cell responses of mouse MC3T3-E1 cells, including cell adhesion and proliferation, are observed on the Zr-Ti-Al-Fe-Cu-Ag BMGs, which reveals their general biosafety. The high-Zr-based BMGs exhibit a higher cell proliferation activity in comparison with that of pure Zr and Ti-6Al-4V alloy. The effects of Zr content on the in vitro biocompatibility can be used to guide the future design of biocompatible Zr-based BMGs. Copyright © 2014 Elsevier B.V. All rights reserved.

Metagenomic analysis revealed highly diverse microbial arsenic metabolism genes in paddy soils with low-arsenic contents

International Nuclear Information System (INIS)

Xiao, Ke-Qing; Li, Li-Guan; Ma, Li-Ping; Zhang, Si-Yu; Bao, Peng; Zhang, Tong; Zhu, Yong-Guan

2016-01-01

Microbe-mediated arsenic (As) metabolism plays a critical role in global As cycle, and As metabolism involves different types of genes encoding proteins facilitating its biotransformation and transportation processes. Here, we used metagenomic analysis based on high-throughput sequencing and constructed As metabolism protein databases to analyze As metabolism genes in five paddy soils with low-As contents. The results showed that highly diverse As metabolism genes were present in these paddy soils, with varied abundances and distribution for different types and subtypes of these genes. Arsenate reduction genes (ars) dominated in all soil samples, and significant correlation existed between the abundance of arr (arsenate respiration), aio (arsenite oxidation), and arsM (arsenite methylation) genes, indicating the co-existence and close-relation of different As resistance systems of microbes in wetland environments similar to these paddy soils after long-term evolution. Among all soil parameters, pH was an important factor controlling the distribution of As metabolism gene in five paddy soils (p = 0.018). To the best of our knowledge, this is the first study using high-throughput sequencing and metagenomics approach in characterizing As metabolism genes in the five paddy soil, showing their great potential in As biotransformation, and therefore in mitigating arsenic risk to humans. - Highlights: • Use metagenomics to analyze As metabolism genes in paddy soils with low-As content. • These genes were ubiquitous, abundant, and associated with diverse microbes. • pH as an important factor controlling their distribution in paddy soil. • Imply combinational effect of evolution and selection on As metabolism genes. - Metagenomics was used to analyze As metabolism genes in paddy soils with low-As contents. These genes were ubiquitous, abundant, and associated with diverse microbes.

Factor analysis in optimization of formulation of high content uniformity tablets containing low dose active substance.

Science.gov (United States)

Lukášová, Ivana; Muselík, Jan; Franc, Aleš; Goněc, Roman; Mika, Filip; Vetchý, David

2017-11-15

Warfarin is intensively discussed drug with narrow therapeutic range. There have been cases of bleeding attributed to varying content or altered quality of the active substance. Factor analysis is useful for finding suitable technological parameters leading to high content uniformity of tablets containing low amount of active substance. The composition of tabletting blend and technological procedure were set with respect to factor analysis of previously published results. The correctness of set parameters was checked by manufacturing and evaluation of tablets containing 1-10mg of warfarin sodium. The robustness of suggested technology was checked by using "worst case scenario" and statistical evaluation of European Pharmacopoeia (EP) content uniformity limits with respect to Bergum division and process capability index (Cpk). To evaluate the quality of active substance and tablets, dissolution method was developed (water; EP apparatus II; 25rpm), allowing for statistical comparison of dissolution profiles. Obtained results prove the suitability of factor analysis to optimize the composition with respect to batches manufactured previously and thus the use of metaanalysis under industrial conditions is feasible. Copyright © 2017 Elsevier B.V. All rights reserved.

Electrochemical treatment of organic wastewater with high salt content. Ko enbun yuki haisui no denkai shori

Energy Technology Data Exchange (ETDEWEB)

Wada, Hideo; Kitamura, Takao; Kato, Shunsaku; Oyashiki, Satoru (Goverment Industrial Research Inst. Shikoku, Takamatsu, (Japan) Toyo Engineering Work Ltd., Tokyo, (Japan))

1990-01-31

Wastewater containing organic pollutants is generally treated by the biological methods like the activated sludge process, etc. But these biological methods are not necessarily applied to the wastewater with high salt content generated at pickles making plants, etc.. In this report, with the objective of application of the electrolytic oxidation treatment to the organic wastewater with high salt content of pickles making plants, the effects of such conditions as pH, temperature and current, etc. on the treatment rate and treatment efficiency were examined, furthermore, the treatment process was simulated on the basis of a simple reaction model, and its simulation results were compared for study with the experimental results. The results are shown below: No effect of pH was observed, hence no pH control is required; The higher temperature of the wastewater accelerates the treatment rate; It was considered that in high temperature, a loss due to autolysis of hypochlorous acid increases, but the current efficiency of generating hypochlorous acid increases too and since the latter effect is bigger, the above phenomenon occurs. The current has a small effect on the treatment efficiency. With the simple reaction model, the change of residual chlorine concentration, etc. with time can be reproduced semiquantitatively. 7 refs., 6 figs.

Phaedra, a protocol-driven system for analysis and validation of high-content imaging and flow cytometry.

Science.gov (United States)

Cornelissen, Frans; Cik, Miroslav; Gustin, Emmanuel

2012-04-01

High-content screening has brought new dimensions to cellular assays by generating rich data sets that characterize cell populations in great detail and detect subtle phenotypes. To derive relevant, reliable conclusions from these complex data, it is crucial to have informatics tools supporting quality control, data reduction, and data mining. These tools must reconcile the complexity of advanced analysis methods with the user-friendliness demanded by the user community. After review of existing applications, we realized the possibility of adding innovative new analysis options. Phaedra was developed to support workflows for drug screening and target discovery, interact with several laboratory information management systems, and process data generated by a range of techniques including high-content imaging, multicolor flow cytometry, and traditional high-throughput screening assays. The application is modular and flexible, with an interface that can be tuned to specific user roles. It offers user-friendly data visualization and reduction tools for HCS but also integrates Matlab for custom image analysis and the Konstanz Information Miner (KNIME) framework for data mining. Phaedra features efficient JPEG2000 compression and full drill-down functionality from dose-response curves down to individual cells, with exclusion and annotation options, cell classification, statistical quality controls, and reporting.

A novel automatic quantification method for high-content screening analysis of DNA double strand-break response.

Science.gov (United States)

Feng, Jingwen; Lin, Jie; Zhang, Pengquan; Yang, Songnan; Sa, Yu; Feng, Yuanming

2017-08-29

High-content screening is commonly used in studies of the DNA damage response. The double-strand break (DSB) is one of the most harmful types of DNA damage lesions. The conventional method used to quantify DSBs is γH2AX foci counting, which requires manual adjustment and preset parameters and is usually regarded as imprecise, time-consuming, poorly reproducible, and inaccurate. Therefore, a robust automatic alternative method is highly desired. In this manuscript, we present a new method for quantifying DSBs which involves automatic image cropping, automatic foci-segmentation and fluorescent intensity measurement. Furthermore, an additional function was added for standardizing the measurement of DSB response inhibition based on co-localization analysis. We tested the method with a well-known inhibitor of DSB response. The new method requires only one preset parameter, which effectively minimizes operator-dependent variations. Compared with conventional methods, the new method detected a higher percentage difference of foci formation between different cells, which can improve measurement accuracy. The effects of the inhibitor on DSB response were successfully quantified with the new method (p = 0.000). The advantages of this method in terms of reliability, automation and simplicity show its potential in quantitative fluorescence imaging studies and high-content screening for compounds and factors involved in DSB response.

Combining Pre- and Post-Nucleation Trajectories for the Synthesis of High FAU-Content Faujasite Nanocrystals from Organic-Free Sols

Energy Technology Data Exchange (ETDEWEB)

Khaleel, Maryam; Xu, Wenqian; Lesch, David A.; Tsapatsis, Michael

2016-06-28

The effects of synthesis conditions on the FAU/EMT content and the size of nanocrystals, formed from inorganic aluminosilicate sols, were investigated. High resolution transmission electron microscopy imaging and comparison of experimental X-ray diffraction patterns with simulations demonstrated that all materials made starting from synthesis mixtures in the composition range (1.8-33) SiO2: 1 Al2O3: (2.7-33) Na2O: (41-1000) H2O contain FAU/EMT intergrowths. Compositions with low water content increase the FAU fraction up to 0.8 but the crystal size exceeds 100 nm. Extension of the higher FAU purity to nanocrystals was achieved only by first mixing the sol at high water content compositions that favor nanocrystal formation and then - after a certain time - lowering by freeze-drying the water to levels favoring the formation of FAU. Cryogenic transmission electron microscopy and small angle X-ray scattering from representative optically clear and colloidally stable precursor sols (aged and crystallized at ambient temperature) reveal the formation of amorphous aggregates before the detection of crystals, in agreement with earlier findings and an existing model for the aggregative growth of the zeolite MFI. The presence of these amorphous aggregates coincides with the aforementioned state of sol that preserves the original trajectory towards nano-crystals after the pronounced reduction of water content by freeze-drying. If water reduction by freeze-drying is applied earlier (before the detection of amorphous aggregates), the sol follows the low water content trajectory towards larger crystals. Despite this memory effect, the sol at this stage is still agnostic towards FAU or EMT formation, the relative content of which is dominantly determined by the final water content. These findings demonstrate that it is possible to combine the effects of pre-and post-nucleation sol composition to steer crystal size and crystal structure, respectively. They confirm precursor

Influence of ultra-high pressure homogenisation on antioxidant capacity, polyphenol and vitamin content of clear apple juice.

Science.gov (United States)

Suárez-Jacobo, Angela; Rüfer, Corinna E; Gervilla, Ramón; Guamis, Buenaventura; Roig-Sagués, Artur X; Saldo, Jordi

2011-07-15

Ultra-high pressure homogenisation (UHPH) is a recently developed technology and is still under study to evaluate its effect on different aspects of its application to food products. The aim of this research work was to evaluate the effect of UHPH treatments on quality characteristics of apple juice such as antioxidant capacity, polyphenol composition, vitamin C and provitamin A contents, in comparison with raw (R) and pasteurised (PA) apple juice. Several UHPH treatments that include combinations of pressure (100, 200 and 300MPa) and inlet temperatures (4 and 20°C) were assayed. Apple juice was pasteurised at 90°C for 4min. Antioxidant capacity was analysed using the oxygen radical antioxidant capacity (ORAC), 2,2-diphenyl-1-picrylhydrazyl (DPPH), trolox equivalent antioxidant capacity (TEAC), ferric reducing antioxidant power (FRAP) assay while total phenolic content was determined by the Folin-Ciocalteau assay. According to the FRAP and DPPH assays, UHPH processing did not change apple juice antioxidant capacity. However, significant differences were detected between samples analysed by TEAC and ORAC assays. In spite of these differences, high correlation values were found between the four antioxidant capacity assays, and also with total polyphenol content. The analysis and quantification of individual phenols by HPLC/DAD analytical technique reflects that UHPH-treatment prevented degradation of these compounds. Vitamin C concentrations did not change in UHPH treated samples, retaining the same value as in raw juice. However, significant losses were observed for provitamin A content, but lower than in PA samples. UHPH-treatments at 300MPa can be an alternative to thermal treatment in order to preserve apple juice quality. Copyright © 2011 Elsevier Ltd. All rights reserved.

Effect of added sugar and ascorbic acid on the anthocyanin content of high pressure processed strawberry juices during storage

Science.gov (United States)

Salamon, B.; Farkas, V.; Kenesei, Gy; Dalmadi, I.

2017-10-01

Berries have high nutritional value and can be processed in many kinds of ways. Their pigments (anthocyanins, flavonoids, carotenoids) have antioxidant properties, effectively neutralize the health-damaging free radicals. High hydrostatic pressure (HHP) technology is a minimal processing technique which is a promising alternative solution instead of traditional preservation technologies. Low molecular weight materials such as colour pigments are well preserved by application of HHP. However, the effect can be influenced by the composition of the treated food matrix. The available scientific information related to the impact of sugar and ascorbic acid content on the preservation of anthocyanins in the samples is controversial. Thus, the aim of our study was to determine the effect of HHP treatment parameters (pressure, treatment time) on the preservation of the anthocyanin content of strawberry juice supplemented by different amounts of sugar and ascorbic acid. 2n type factorial experimental design was used to evaluate the effect of four factors (refraction index, ascorbic acid, pressure, treatment time) on the residual content of total anthocyanins immediately after HHP treatment and after 21 days storage at room temperature.

Rapid estimation of the organic sulphur content of kerogens, coals and asphaltenes by pyrolysis-gas chromatography

NARCIS (Netherlands)

Sinninghe Damsté, J.S.; Eglinton, T.I.; Kohnen, M.E.L.; Leeuw, J.W. de

1990-01-01

A pyrolysis-gas Chromatographic (py-g.c.) method for estimation of the Sorg/C ratio in kerogens and other forms of sedimentary macromolecular organic matter is described. The method is based upon flash pyrolysis at 610 °C for 10s and areal integration of the FID peaks attributed to

Advanced Cell Classifier: User-Friendly Machine-Learning-Based Software for Discovering Phenotypes in High-Content Imaging Data.

Science.gov (United States)

Piccinini, Filippo; Balassa, Tamas; Szkalisity, Abel; Molnar, Csaba; Paavolainen, Lassi; Kujala, Kaisa; Buzas, Krisztina; Sarazova, Marie; Pietiainen, Vilja; Kutay, Ulrike; Smith, Kevin; Horvath, Peter

2017-06-28

High-content, imaging-based screens now routinely generate data on a scale that precludes manual verification and interrogation. Software applying machine learning has become an essential tool to automate analysis, but these methods require annotated examples to learn from. Efficiently exploring large datasets to find relevant examples remains a challenging bottleneck. Here, we present Advanced Cell Classifier (ACC), a graphical software package for phenotypic analysis that addresses these difficulties. ACC applies machine-learning and image-analysis methods to high-content data generated by large-scale, cell-based experiments. It features methods to mine microscopic image data, discover new phenotypes, and improve recognition performance. We demonstrate that these features substantially expedite the training process, successfully uncover rare phenotypes, and improve the accuracy of the analysis. ACC is extensively documented, designed to be user-friendly for researchers without machine-learning expertise, and distributed as a free open-source tool at www.cellclassifier.org. Copyright © 2017 Elsevier Inc. All rights reserved.

Regulation of FA and TAG biosynthesis pathway genes in endosperms and embryos of high and low oil content genotypes of Jatropha curcas L.

Science.gov (United States)

Sood, Archit; Chauhan, Rajinder Singh

2015-09-01

The rising demand for biofuels has raised concerns about selecting alternate and promising renewable energy crops which do not compete with food supply. Jatropha (Jatropha curcas L.), a non-edible energy crop of the family euphorbiaceae, has the potential of providing biodiesel feedstock due to the presence of high proportion of unsaturated fatty acids (75%) in seed oil which is mainly accumulated in endosperm and embryo. The molecular basis of seed oil biosynthesis machinery has been studied in J. curcas, however, what genetic differences contribute to differential oil biosynthesis and accumulation in genotypes varying for oil content is poorly understood. We investigated expression profile of 18 FA and TAG biosynthetic pathway genes in different developmental stages of embryo and endosperm from high (42%) and low (30%) oil content genotypes grown at two geographical locations. Most of the genes showed relatively higher expression in endosperms of high oil content genotype, whereas no significant difference was observed in endosperms versus embryos of low oil content genotype. The promoter regions of key genes from FA and TAG biosynthetic pathways as well as other genes implicated in oil accumulation were analyzed for regulatory elements and transcription factors specific to oil or lipid accumulation in plants such as Dof, CBF (LEC1), SORLIP, GATA and Skn-1_motif etc. Identification of key genes from oil biosynthesis and regulatory elements specific to oil deposition will be useful not only in dissecting the molecular basis of high oil content but also improving seed oil content through transgenic or molecular breeding approaches. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

Processing of oil products using complex radiation-thermal treatment and radiation oxonolysis

International Nuclear Information System (INIS)

Zaikin, Yu.A.; Zaikina, R.F.

2002-01-01

Most of industrial radiation facilities afford an opportunity to produce a considerable amount of reactive ozone-containing gaseous mixtures parallel to the basic production that causes no detriment to the output of the main designed product. The synergetic action of the ozone-containing mixtures and ionizing radiation is of a special interest for industrial application since it can be efficiently used in a wide range of technologies, in particular, for stimulation of chemical conversion in hydrocarbons accompanied by intensive oxidizing processes. In this paper the effect of simultaneous radiation-thermal processing and radiation oxonolysis on hydrocarbon chemical conversion, and subsequent alterations in composition and properties of oil products were studied on the example of high-viscous oil (Karazhanbas field, Kazakhstan) subjected to irradiation by 2 MeV electrons combined with radiation ozonization in the bubbling mode. It was stated that application of the bubbling mode for radiation-induced ozonization of high-viscous oil leads to decrease in the yields of engine fuels in average by 8-10 % compared with those obtained in the conditions when radiation-thermal cracking was applied without bubbling. In the latter case mean yields of the wide gas-oil fraction with boiling start temperature of 350 deg. C, that included gasoline, kerosene, and diesel fuel, were about 76-80 %. Decrease in the gasoline yields does not lead to noticeable alterations in hydrocarbon contents of the gasoline fraction (boiling beginning bellow 175 deg. C) compared with gasoline produced be radiation-thermal cracking, in both cases it meets requirements for high quality standards. However, essential difference was observed in properties of heavy residua of oil processing (oil fractions with T boil >350 deg. C), i.e. the fractions that contained high concentrations of asphaltenes and pitches. Application of radiation oxonolysis diminishes concentrations of high-molecular aromatic

Description of pedagogical content knowledge (PCK) and content knowledge on Muhammadiyah Semarang University's preservice teacher

Science.gov (United States)

Astuti, Andari Puji; Wijayatiningsih, Testiana Deni; Azis, Abdul; Sumarti, Sri Susilogati; Barati, Dwi Anggani Linggar

2017-12-01

One of the competencies of teachers to be mastered under the constitution is pedagogic competence. This study aims to provide an overview of the pedagogic competence of Preservice teachers through the mastery of Pedagogical Content Knowledge (PCK) and Content knowledge (CK). The research method used is descriptive qualitative, with data retrieval technique through essay tests, questionnaire and interview. The results showed that of the five PCK indicators, only knowledge of learning strategies to teach chemistry already in high category. For Content Knowledge of preservice teachers are in the middle category for indicators of knowledge of disciplinary content, whereas knowledge that alternative frameworks for thinking about the content exist and the knowledge of the relationship between big ideas and the supporting ideas in a content area is in the fair category.

Cytological study of DNA content and nuclear morphometric analysis for aid in the diagnosis of high-grade dysplasia within oral leukoplakia.

Science.gov (United States)

Yang, Xi; Xiao, Xuan; Wu, Wenyan; Shen, Xuemin; Zhou, Zengtong; Liu, Wei; Shi, Linjun

2017-09-01

To quantitatively examine the DNA content and nuclear morphometric status of oral leukoplakia (OL) and investigate its association with the degree of dysplasia in a cytologic study. Oral cytobrush biopsy was carried out to obtain exfoliative epithelial cells from lesions before scalpel biopsy at the same location in a blinded series of 70 patients with OL. Analysis of nuclear morphometry and DNA content status using image cytometry was performed with oral smears stained with the Feulgen-thionin method. Nuclear morphometric analysis revealed significant differences in DNA content amount, DNA index, nuclear area, nuclear radius, nuclear intensity, sphericity, entropy, and fractal dimension (all P content analysis identified 34 patients with OL (48.6%) with DNA content abnormality. Nonhomogeneous lesion (P = .018) and high-grade dysplasia (P = .008) were significantly associated with abnormal DNA content. Importantly, the positive correlation between the degree of oral dysplasia and DNA content status was significant (P = .004, correlation coefficient = 0.342). Cytology analysis of DNA content and nuclear morphometric status using image cytometry may support their use as a screening and monitoring tool for OL progression. Copyright © 2017 Elsevier Inc. All rights reserved.

Design of an assessment to probe teachers’ content knowledge for teaching: An example from energy in high school physics

Directory of Open Access Journals (Sweden)

Eugenia Etkina

2018-05-01

Full Text Available Research into teacher learning and practice over the last three decades shows that the teachers of a specific subject need to possess knowledge that is different from the knowledge of other content experts. Yet this specialized version of content knowledge that teachers need to plan instruction, respond to student ideas, and assess student understanding in real time is a theoretically elusive construct. It is crucial for the fields of precollege teacher preparation, teacher professional education, and postsecondary faculty professional development to (a clarify the construct that underlies this specialized content knowledge, (b operationalize it in some domain, (c measure it in both static contexts and as it is enacted in the classroom, and (d correlate its presence with “richness” of classroom instruction and its effect on student learning. This paper documents a piece of a multiyear, multi-institutional effort to investigate points (a–(d in the domain of energy in the first high school physics course. In particular, we describe the framework that we developed to clarify content knowledge for teaching in the context of high school energy learning. We then outline the process through which we developed, tested, and refined a “paper-and-pencil” assessment administered on a computer and discuss the substantive and psychometric features of several items based on a field test of the final form of the assessment. We choose to discuss these items for a dual purpose: to illustrate the application of our general framework and to present performance findings from a sample of 362 practicing high school teachers of physics.

Aging of SRC liquids

Science.gov (United States)

Hara, T.; Jones, L.; Tewari, K. C.; Li, N. C.

1981-02-01

The viscosity of SRC-LL liquid increases when subjected to accelerated aging by bubbling oxygen in the presence of copper strip at 62°C. Precipitates are formed and can be separated from the aged liquid by Soxhlet extraction with pentane. A 30-70 blend of SRC-I with SRC-LL was subjected to oxygen aging in the absence of copper, and the viscosity increased dramatically after 6 days at 62°. The content of preasphaltene and its molecular size increase with time of aging, accompanied by decrease of asphaltene and pentane-soluble contents. For the preasphaltene fraction on aging, gel permeation chromatography shows formation of larger particles. ESR experiments show that with oxygen aging, spin concentration in the preasphaltene fraction decreases. Perhaps some semiquinone, together with di- and tri-substituted phenoxy radicals, generated by oxygen aging of the coal liquid, interact with the free radicals already present in coal to yield larger particles and reduce free radical concentration. We are currently using the very high-field (600-MHz) NMR spectrometer at Mellon Institute to determine changes in structural parameters before and after aging of SRC-II and its chromatographically separated fractions.

Contents of Stereotypes toward Woman Subgroups: An Investigation in the Framework of Stereotype Content Model

Directory of Open Access Journals (Sweden)

Timucin Aktan

2016-12-01

Full Text Available The aim of the study was to investigate the stereotype contents toward woman subgroups and relate these contents to social-structural predictors and sexism. In this respect, 119 university students were recruited for the first study and they were asked to rate 10 woman subgroups in terms of their competence and warmth, and their status and competitiveness. Participants' level of sexism was also measured using ambivalent sexism scale. The findings of the first study revealed that competence and warmth were the two fundamental dimensions of the stereotype contents, these stereotypes could be depicted in three clusters, the content of many women stereotypes were mixed, and status was linked to competence and competition was related to lack of warmth. Besides replicating the main hypotheses of stereotype content model, the findings supported its two basic assumptions, i.e. negative stereotypes are not necessary to reveal stereotype clusters and personal stereotypes are more open to motivational concerns. Finally, sexism was related only with competition, but not with stereotype contents. Since, high competent / high warm cluster was not observed in the first study, the number of woman subgroups was increased in the second study. Thus, 86 university students were asked to rate 18 women subgroups on the scales used in the first study. Results replicated the findings of the first study, supporting the main hypothesis of stereotype content model. The findings of the studies were discussed in the light of relevant literature.

Coal liquefaction with preasphaltene recycle

Science.gov (United States)

Weimer, Robert F.; Miller, Robert N.

1986-01-01

A coal liquefaction system is disclosed with a novel preasphaltene recycle from a supercritical extraction unit to the slurry mix tank wherein the recycle stream contains at least 90% preasphaltenes (benzene insoluble, pyridine soluble organics) with other residual materials such as unconverted coal and ash. This subject process results in the production of asphaltene materials which can be subjected to hydrotreating to acquire a substitute for No. 6 fuel oil. The preasphaltene-predominant recycle reduces the hydrogen consumption for a process where asphaltene material is being sought.

Optimization of conditions to achieve high content of gamma amino butyric acid in germinated black rice, and changes in bioactivities

Directory of Open Access Journals (Sweden)

Chaiyavat CHAIYASUT

Full Text Available Abstract The present study estimated the optimum germination conditions to achieve high content of Gamma-amino butyric acid (GABA and other phytochemicals in Thai black rice cultivar Kum Payao (BR. The Box–Behnken design of response surface methodology was employed to optimize the germination conditions. The changes in the GABA, phytochemical content, impact of salt, and temperature stress variation on phytochemical content, and stability of GABA were studied. The results showed that 12 h of soaking at pH 7, followed by 36 h of germination was the optimum condition to achieve maximum GABA content (0.2029 mg/g of germinated BR (GBR. The temperature (8 and 30 °C, and salt (50-200 mM NaCl content affected the phytochemicals of GBR, especially GABA, and anthocyanins. Obviously, the antioxidant capability, and enzyme (α-amylase and α-glucosidase inhibiting nature of BR was significantly (P < 0.001 increased after germination. The storage of GBR at 4 °C significantly, preserved the GABA content (∼80% for 45 days. Primarily, the current study revealed the changes in phytochemical content, and bioactivity of Thai black rice cr. Kum Payao during germination. More studies should be carried out on pharmacological benefits of GABA-rich GBR.

Sharing of Alcohol-Related Content on Social Networking Sites: Frequency, Content, and Correlates.

Science.gov (United States)

Erevik, Eilin K; Torsheim, Torbjørn; Vedaa, Øystein; Andreassen, Cecilie S; Pallesen, Ståle

2017-05-01

The present study aimed to explore students' reports of their sharing of alcohol-related content on different social networking sites (i.e., frequency of sharing and connotations of alcohol-related posts), and to identify indicators of such posting. Students at the four largest institutions for higher education in Bergen, Norway, were invited to participate in an Internet-based survey. The sample size was 11,236 (a 39.4% response rate). The survey included questions about disclosure of alcohol-related content on social networking sites, alcohol use (using the Alcohol Use Disorders Identification Test), personality factors (using the Mini-IPIP), and demographic characteristics. Binary logistic regressions were used to analyze indicators of frequent sharing of alcohol-related content depicting positive and negative aspects of alcohol use. A majority of the students had posted alcohol-related content (71.0%), although few reported having done so frequently. Positive aspects of alcohol use (e.g., enjoyment or social community) were most frequently shared. Young, single, and extroverted students with high alcohol consumption were more likely to report frequent sharing of alcohol-related content. Positive attitudes toward posting alcohol-related content and reports of exposure to such content particularly increased the likelihood of one's own posting of alcohol-related content. Positive aspects of alcohol use seem to be emphasized on social networking sites. Sharing of alcohol-related content is associated with heightened alcohol use, which implies that such sites can be relevant for prevention agents. Social influence from social networking sites, such as exposure to others' alcohol-related content, is associated with one's own sharing of similar content.

Fluorine content of Fukien teas

Energy Technology Data Exchange (ETDEWEB)

Wang, T H; Lin, C S; Wu, C; Liao, C E; Lin, H Y

1949-01-01

A study was made on the fluorine contents of Fukien teas and analytical results indicated the amount ranged from 5.7 to 35.5 mg. per 100 grams of dry tea. The high content of fluorine was found not to be due to contamination nor to the high fluorine content of the soil in which the tea plant was cultivated. Differences in the methods of manufacture had no effect on the fluorine content of the final products. Different varieties of tea plants have different powers to absorb fluorine from the soil. Of the two varieties of tea plants studied, Shui-Sen leaves possessed the lower fluorine content. Age of the tea leaves exerted an important influence on the fluorine content, the older leaves containing considerably more fluorine than the younger. The amount of fluorine that may be extracted in a two per cent infusion varies from 29.1 per cent for fresh leaves to 50.5 per cent for black tea. The process of roasting and rolling rendered the fluorine more soluble, hence the amount extracted increased in green tea. Fermentation further increased the extractability of the fluorine; thus the amount extracted was the highest in black tea, which was fermented, less in the semi-fermented oolong tea, and least in the unfermented green tea. The extractability of fluorine was also increased with age of the leaves.

DETERMINATION OF STRONTIUM IONS IN WATERS WITH A HIGH CONTENT OF SODIUM IONS

Directory of Open Access Journals (Sweden)

Tatiana Mitina

2015-06-01

Full Text Available This paper reports on the influence of sodium ions on experimental determination of strontium ions concentration in waters with a high content of sodium ions by using emission flame photometry and atomic absorption spectroscopy. For the method of emission flame photometry it was shown that at a wavelength of 460.7 nm (spectral emission line of strontium the emission is linearly dependent on the concentration of sodium ions. The greatest impact of high concentrations of sodium ions on the result of determination the strontium ions concentration has been registered at low levels of strontium. The influence of nitric acid on the results is also discussed. In the case of using atomic absorption spectroscopy method no influence of sodium ions and nitric acid on the results of determination the strontium ions concentration was revealed. The metrological characteristics of both methods are evaluated.

General Staining and Segmentation Procedures for High Content Imaging and Analysis.

Science.gov (United States)

Chambers, Kevin M; Mandavilli, Bhaskar S; Dolman, Nick J; Janes, Michael S

2018-01-01

Automated quantitative fluorescence microscopy, also known as high content imaging (HCI), is a rapidly growing analytical approach in cell biology. Because automated image analysis relies heavily on robust demarcation of cells and subcellular regions, reliable methods for labeling cells is a critical component of the HCI workflow. Labeling of cells for image segmentation is typically performed with fluorescent probes that bind DNA for nuclear-based cell demarcation or with those which react with proteins for image analysis based on whole cell staining. These reagents, along with instrument and software settings, play an important role in the successful segmentation of cells in a population for automated and quantitative image analysis. In this chapter, we describe standard procedures for labeling and image segmentation in both live and fixed cell samples. The chapter will also provide troubleshooting guidelines for some of the common problems associated with these aspects of HCI.

Influence of molybdenum content on transformation behavior of high performance bridge steel during continuous cooling

International Nuclear Information System (INIS)

Chen, Jun; Tang, Shuai; Liu, Zhenyu; Wang, Guodong

2013-01-01

Highlights: ► The bainite transformation field was refined. ► The empirical equation to estimate the GF s was established. ► Transformation behavior was studied with serially increasing Mo addition. ► The molybdenum content can be lowered as the cooling rate is increased. ► GF transformation field is also shifted to right by increasing Mo content. - Abstract: The continuous-cooling-transformation (CCT) diagrams of high performance bridge steel with different molybdenum content were plotted by means of a combined method of dilatometry and metallography. The results show that the molybdenum addition of 0.17 wt% does not noticeably alter the transformation behavior, whereas 0.38 wt% significantly. In addition, the molybdenum addition of 0.38 wt% completely eliminates the formation of polygonal ferrite (PF) and significantly lower the granular ferrite (GF) transformation starting temperatures throughout the range of cooling rates studied. At lower cooling rates, with the increase of the molybdenum content, the martensite/austenite (M/A) constituents are noticeably refined, whereas the effects are not obvious at higher cooling rates. Moreover, the molybdenum addition of 0.38 wt% can significantly increase the Vickers hardness, but the Vickers hardness increments (by comparison of Mo-0.17wt% steel and Mo-0.38wt% steel) are sharply reduced at the cooling rate of 30 °C/s, indicating that at higher cooling rate, the molybdenum usage can be saved and the higher strengthen can be also gained. It could be found the GF transformation starting temperature is linear with the cooling rate. The empirical equation was established to calculate GF transformation starting temperatures, and the calculated values are in good agreement with measured ones

Automated microscopy for high-content RNAi screening

Science.gov (United States)

2010-01-01

Fluorescence microscopy is one of the most powerful tools to investigate complex cellular processes such as cell division, cell motility, or intracellular trafficking. The availability of RNA interference (RNAi) technology and automated microscopy has opened the possibility to perform cellular imaging in functional genomics and other large-scale applications. Although imaging often dramatically increases the content of a screening assay, it poses new challenges to achieve accurate quantitative annotation and therefore needs to be carefully adjusted to the specific needs of individual screening applications. In this review, we discuss principles of assay design, large-scale RNAi, microscope automation, and computational data analysis. We highlight strategies for imaging-based RNAi screening adapted to different library and assay designs. PMID:20176920

3D high-content screening for the identification of compounds that target cells in dormant tumor spheroid regions

Energy Technology Data Exchange (ETDEWEB)

Wenzel, Carsten; Riefke, Björn; Gründemann, Stephan; Krebs, Alice; Christian, Sven; Prinz, Florian; Osterland, Marc; Golfier, Sven; Räse, Sebastian [Bayer Pharma AG, Global Drug Discovery, Muellerstrasse 178, 13353 Berlin (Germany); Ansari, Nariman [Physical Biology Group, Buchmann Institute for Molecular Life Sciences (BMLS), Goethe University Frankfurt (Germany); Esner, Milan; Bickle, Marc [Max Planck Institute of Molecular Cell Biology and Genetics, High-Throughput Technology Development Studio (TDS), Dresden (Germany); Pampaloni, Francesco; Mattheyer, Christian; Stelzer, Ernst H. [Physical Biology Group, Buchmann Institute for Molecular Life Sciences (BMLS), Goethe University Frankfurt (Germany); Parczyk, Karsten; Prechtl, Stefan [Bayer Pharma AG, Global Drug Discovery, Muellerstrasse 178, 13353 Berlin (Germany); Steigemann, Patrick, E-mail: Patrick.Steigemann@bayer.com [Bayer Pharma AG, Global Drug Discovery, Muellerstrasse 178, 13353 Berlin (Germany)

2014-04-15

Cancer cells in poorly vascularized tumor regions need to adapt to an unfavorable metabolic microenvironment. As distance from supplying blood vessels increases, oxygen and nutrient concentrations decrease and cancer cells react by stopping cell cycle progression and becoming dormant. As cytostatic drugs mainly target proliferating cells, cancer cell dormancy is considered as a major resistance mechanism to this class of anti-cancer drugs. Therefore, substances that target cancer cells in poorly vascularized tumor regions have the potential to enhance cytostatic-based chemotherapy of solid tumors. With three-dimensional growth conditions, multicellular tumor spheroids (MCTS) reproduce several parameters of the tumor microenvironment, including oxygen and nutrient gradients as well as the development of dormant tumor regions. We here report the setup of a 3D cell culture compatible high-content screening system and the identification of nine substances from two commercially available drug libraries that specifically target cells in inner MCTS core regions, while cells in outer MCTS regions or in 2D cell culture remain unaffected. We elucidated the mode of action of the identified compounds as inhibitors of the respiratory chain and show that induction of cell death in inner MCTS core regions critically depends on extracellular glucose concentrations. Finally, combinational treatment with cytostatics showed increased induction of cell death in MCTS. The data presented here shows for the first time a high-content based screening setup on 3D tumor spheroids for the identification of substances that specifically induce cell death in inner tumor spheroid core regions. This validates the approach to use 3D cell culture screening systems to identify substances that would not be detectable by 2D based screening in otherwise similar culture conditions. - Highlights: • Establishment of a novel method for 3D cell culture based high-content screening. • First reported high-content

3D high-content screening for the identification of compounds that target cells in dormant tumor spheroid regions

International Nuclear Information System (INIS)

Wenzel, Carsten; Riefke, Björn; Gründemann, Stephan; Krebs, Alice; Christian, Sven; Prinz, Florian; Osterland, Marc; Golfier, Sven; Räse, Sebastian; Ansari, Nariman; Esner, Milan; Bickle, Marc; Pampaloni, Francesco; Mattheyer, Christian; Stelzer, Ernst H.; Parczyk, Karsten; Prechtl, Stefan; Steigemann, Patrick

2014-01-01

Cancer cells in poorly vascularized tumor regions need to adapt to an unfavorable metabolic microenvironment. As distance from supplying blood vessels increases, oxygen and nutrient concentrations decrease and cancer cells react by stopping cell cycle progression and becoming dormant. As cytostatic drugs mainly target proliferating cells, cancer cell dormancy is considered as a major resistance mechanism to this class of anti-cancer drugs. Therefore, substances that target cancer cells in poorly vascularized tumor regions have the potential to enhance cytostatic-based chemotherapy of solid tumors. With three-dimensional growth conditions, multicellular tumor spheroids (MCTS) reproduce several parameters of the tumor microenvironment, including oxygen and nutrient gradients as well as the development of dormant tumor regions. We here report the setup of a 3D cell culture compatible high-content screening system and the identification of nine substances from two commercially available drug libraries that specifically target cells in inner MCTS core regions, while cells in outer MCTS regions or in 2D cell culture remain unaffected. We elucidated the mode of action of the identified compounds as inhibitors of the respiratory chain and show that induction of cell death in inner MCTS core regions critically depends on extracellular glucose concentrations. Finally, combinational treatment with cytostatics showed increased induction of cell death in MCTS. The data presented here shows for the first time a high-content based screening setup on 3D tumor spheroids for the identification of substances that specifically induce cell death in inner tumor spheroid core regions. This validates the approach to use 3D cell culture screening systems to identify substances that would not be detectable by 2D based screening in otherwise similar culture conditions. - Highlights: • Establishment of a novel method for 3D cell culture based high-content screening. • First reported high-content

An Improved Variant of Soybean Type 1 Diacylglycerol Acyltransferase Increases the Oil Content and Decreases the Soluble Carbohydrate Content of Soybeans.

Science.gov (United States)

Roesler, Keith; Shen, Bo; Bermudez, Ericka; Li, Changjiang; Hunt, Joanne; Damude, Howard G; Ripp, Kevin G; Everard, John D; Booth, John R; Castaneda, Leandro; Feng, Lizhi; Meyer, Knut

2016-06-01

Kinetically improved diacylglycerol acyltransferase (DGAT) variants were created to favorably alter carbon partitioning in soybean (Glycine max) seeds. Initially, variants of a type 1 DGAT from a high-oil, high-oleic acid plant seed, Corylus americana, were screened for high oil content in Saccharomyces cerevisiae Nearly all DGAT variants examined from high-oil strains had increased affinity for oleoyl-CoA, with S0.5 values decreased as much as 4.7-fold compared with the wild-type value of 0.94 µm Improved soybean DGAT variants were then designed to include amino acid substitutions observed in promising C. americana DGAT variants. The expression of soybean and C. americana DGAT variants in soybean somatic embryos resulted in oil contents as high as 10% and 12%, respectively, compared with only 5% and 7.6% oil achieved by overexpressing the corresponding wild-type DGATs. The affinity for oleoyl-CoA correlated strongly with oil content. The soybean DGAT variant that gave the greatest oil increase contained 14 amino acid substitutions out of a total of 504 (97% sequence identity with native). Seed-preferred expression of this soybean DGAT1 variant increased oil content of soybean seeds by an average of 3% (16% relative increase) in highly replicated, single-location field trials. The DGAT transgenes significantly reduced the soluble carbohydrate content of mature seeds and increased the seed protein content of some events. This study demonstrated that engineering of the native DGAT enzyme is an effective strategy to improve the oil content and value of soybeans. © 2016 American Society of Plant Biologists. All Rights Reserved.

Standards-based Content Resources: A Prerequisite for Content Integration and Content Interoperability

Directory of Open Access Journals (Sweden)

Christian Galinski

2010-05-01

Full Text Available Objective: to show how standards-based approaches for content standardization, content management, content related services and tools as well as the respective certification systems not only guarantee reliable content integration and content interoperability, but also are of particular benefit to people with special needs in eAccessibility/eInclusion. Method: document MoU/MG/05 N0221 ''Semantic Interoperability and the need for a coherent policy for a framework of distributed, possibly federated repositories for all kinds of content items on a world-wide scale''2, which was adopted in 2005, was a first step towards the formulation of global interoperability requirements for structured content. These requirements -based on advanced terminological principles- were taken up in EU-projects such as IN-SAFETY (INfrastructure and SAFETY and OASIS (Open architecture for Accessible Services Integration and Standardization. Results: Content integration and content interoperability are key concepts in connection with the emergence of state-of-the-art distributed and federated databases/repositories of structured content. Given the fact that linguistic content items are increasingly combined with or embedded in non-linguistic content items (and vice versa, a systemic and generic approach to data modelling and content management has become the order of the day. Fulfilling the requirements of capability for multilinguality and multimodality, based on open standards makes software and database design fit for eAccessibility/eInclusion from the outset. It also makes structured content capable for global content integration and content interoperability, because it enhances its potential for being re-used and re-purposed in totally different eApplications. Such content as well as the methods, tools and services applied can be subject to new kinds of certification schemes which also should be based on standards. Conclusions: Content must be totally reliable in some

A Liposomal Formulation Able to Incorporate a High Content of Paclitaxel and Exert Promising Anticancer Effect

Directory of Open Access Journals (Sweden)

Pei Kan

2011-01-01

Full Text Available A liposome formulation for paclitaxel was developed in this study. The liposomes, composed of naturally unsaturated and hydrogenated phosphatidylcholines, with significant phase transition temperature difference, were prepared and characterized. The liposomes exhibited a high content of paclitaxel, which was incorporated within the segregated microdomains coexisting on phospholipid bilayer of liposomes. As much as 15% paclitaxel to phospholipid molar ratio were attained without precipitates observed during preparation. In addition, the liposomes remained stable in liquid form at 4∘C for at least 6 months. The special composition of liposomal membrane which could reduce paclitaxel aggregation could account for such a capacity and stability. The cytotoxicity of prepared paclitaxel liposomes on the colon cancer C-26 cell culture was comparable to Taxol. Acute toxicity test revealed that LD50 for intravenous bolus injection in mice exceeded by 40 mg/kg. In antitumor efficacy study, the prepared liposomal paclitaxel demonstrated the increase in the efficacy against human cancer in animal model. Taken together, the novel formulated liposomes can incorporate high content of paclitaxel, remaining stable for long-term storage. These animal data also demonstrate that the liposomal paclitaxel is promising for further clinical use.

A Photobioreactor System for Precision Cultivation of Photoautotrophic Microorganisms and for High-Content Analysis of Suspension Dynamics

Czech Academy of Sciences Publication Activity Database

Nedbal, Ladislav; Trtílek, M.; Červený, Jan; Komárek, Ondřej; Pakrasi, Himadri B.

2008-01-01

Roč. 100, č. 5 (2008), s. 902-910 ISSN 0006-3592 R&D Projects: GA ČR GA206/05/0894 Institutional research plan: CEZ:AV0Z60870520 Keywords : algae * cyanobacteria * high-content monitoring * microbial growth * photosynthesis * systems biology Subject RIV: EI - Biotechnology ; Bionics Impact factor: 2.936, year: 2008

A prototype method for diagnosing high ice water content probability using satellite imager data

Science.gov (United States)

Yost, Christopher R.; Bedka, Kristopher M.; Minnis, Patrick; Nguyen, Louis; Strapp, J. Walter; Palikonda, Rabindra; Khlopenkov, Konstantin; Spangenberg, Douglas; Smith, William L., Jr.; Protat, Alain; Delanoe, Julien

2018-03-01

Recent studies have found that ingestion of high mass concentrations of ice particles in regions of deep convective storms, with radar reflectivity considered safe for aircraft penetration, can adversely impact aircraft engine performance. Previous aviation industry studies have used the term high ice water content (HIWC) to define such conditions. Three airborne field campaigns were conducted in 2014 and 2015 to better understand how HIWC is distributed in deep convection, both as a function of altitude and proximity to convective updraft regions, and to facilitate development of new methods for detecting HIWC conditions, in addition to many other research and regulatory goals. This paper describes a prototype method for detecting HIWC conditions using geostationary (GEO) satellite imager data coupled with in situ total water content (TWC) observations collected during the flight campaigns. Three satellite-derived parameters were determined to be most useful for determining HIWC probability: (1) the horizontal proximity of the aircraft to the nearest overshooting convective updraft or textured anvil cloud, (2) tropopause-relative infrared brightness temperature, and (3) daytime-only cloud optical depth. Statistical fits between collocated TWC and GEO satellite parameters were used to determine the membership functions for the fuzzy logic derivation of HIWC probability. The products were demonstrated using data from several campaign flights and validated using a subset of the satellite-aircraft collocation database. The daytime HIWC probability was found to agree quite well with TWC time trends and identified extreme TWC events with high probability. Discrimination of HIWC was more challenging at night with IR-only information. The products show the greatest capability for discriminating TWC ≥ 0.5 g m-3. Product validation remains challenging due to vertical TWC uncertainties and the typically coarse spatio-temporal resolution of the GEO data.

Growth Mechanism and Origin of High s p3 Content in Tetrahedral Amorphous Carbon

Science.gov (United States)

Caro, Miguel A.; Deringer, Volker L.; Koskinen, Jari; Laurila, Tomi; Csányi, Gábor

2018-04-01

We study the deposition of tetrahedral amorphous carbon (ta-C) films from molecular dynamics simulations based on a machine-learned interatomic potential trained from density-functional theory data. For the first time, the high s p3 fractions in excess of 85% observed experimentally are reproduced by means of computational simulation, and the deposition energy dependence of the film's characteristics is also accurately described. High confidence in the potential and direct access to the atomic interactions allow us to infer the microscopic growth mechanism in this material. While the widespread view is that ta-C grows by "subplantation," we show that the so-called "peening" model is actually the dominant mechanism responsible for the high s p3 content. We show that pressure waves lead to bond rearrangement away from the impact site of the incident ion, and high s p3 fractions arise from a delicate balance of transitions between three- and fourfold coordinated carbon atoms. These results open the door for a microscopic understanding of carbon nanostructure formation with an unprecedented level of predictive power.

NMR and Chemometric Characterization of Vacuum Residues and Vacuum Gas Oils from Crude Oils of Different Origin

Directory of Open Access Journals (Sweden)

Jelena Parlov Vuković

2015-03-01

Full Text Available NMR spectroscopy in combination with statistical methods was used to study vacuum residues and vacuum gas oils from 32 crude oils of different origin. Two chemometric metodes were applied. Firstly, principal component analysis on complete spectra was used to perform classification of samples and clear distinction between vacuum residues and vacuum light and heavy gas oils were obtained. To quantitatively predict the composition of asphaltenes, principal component regression models using areas of resonance signals spaned by 11 frequency bins of the 1H NMR spectra were build. The first 5 principal components accounted for more than 94 % of variations in the input data set and coefficient of determination for correlation between measured and predicted values was R2 = 0.7421. Although this value is not significant, it shows the underlying linear dependence in the data. Pseudo two-dimensional DOSY NMR experiments were used to assess the composition and structural properties of asphaltenes in a selected crude oil and its vacuum residue on the basis of their different hydrodynamic behavior and translational diffusion coefficients. DOSY spectra showed the presence of several asphaltene aggregates differing in size and interactions they formed. The obtained results have shown that NMR techniques in combination with chemometrics are very useful to analyze vacuum residues and vacuum gas oils. Furthermore, we expect that our ongoing investigation of asphaltenes from crude oils of different origin will elucidate in more details composition, structure and properties of these complex molecular systems.

Reduction of benzene and naphthalene mass transfer from crude oils by aging-induced interfacial films.

Science.gov (United States)

Ghoshal, Subhasis; Pasion, Catherine; Alshafie, Mohammed

2004-04-01

Semi-rigid films or skins form at the interface of crude oil and water as a result of the accumulation of asphaltene and resin fractions when the water-immiscible crude oil is contacted with water for a period of time or "aged". The time varying patterns of area-independent mass transfer coefficients of two compounds, benzene and naphthalene, for dissolution from crude oil and gasoline were determined. Aqueous concentrations of the compounds were measured in the eluent from flow-through reactors, where a nondispersed oil phase and constant oil-water interfacial area were maintained. For Brent Blend crude oil and for gasoline amended with asphaltenes and resins, a rapid decrease in both benzene and naphthalene mass transfer coefficients over the first few days of aging was observed. The mass transfer coefficients of the two target solutes were reduced by up to 80% over 35 d although the equilibrium partition coefficients were unchanged. Aging of gasoline, which has negligible amounts of asphaltene and resin, did not result in a change in the solute mass transfer coefficients. The study demonstrates that formation of crude oil-water interfacial films comprised of asphaltenes and resins contribute to time-dependent decreases in rates of release of environmentally relevant solutes from crude oils and may contribute to the persistence of such solutes at crude oil-contaminated sites. It is estimated that the interfacial film has an extremely low film mass transfer coefficient in the range of 10(-6) cm/min.

Heavy Oil Upgrading and Enhanced Recovery in a Steam Injection Process Assisted by NiO- and PdO-Functionalized SiO2 Nanoparticulated Catalysts

Directory of Open Access Journals (Sweden)

Luisana Cardona

2018-03-01

Full Text Available This work aims to investigate the effect of active catalytic nanoparticles on the improvement of the efficiency in recovery of a continuous steam injection process. Catalytic nanoparticles were selected through batch-adsorption experiments and the subsequent evaluation of the temperature for catalytic steam gasification in a thermogravimetric analyzer. A nanoparticulated SiO2 support was functionalized with 1.0 wt % of NiO and PdO nanocrystals, respectively, to improve the catalytic activity of the nanoparticles. Oil recovery was evaluated using a sand pack in steam injection scenarios in the absence and presence of a 500 mg/L SiNi1Pd1 nanoparticles-based nanofluid. The displacement test was carried out by constructing the base curves with water injection followed by steam injection in the absence and presence of the prepared treatment. The oil recovery increased 56% after steam injection with nanoparticles in comparison with the steam injection in the absence of the catalysts. The API gravity increases from 7.2° to 12.1°. Changes in the asphaltenes fraction corroborated the catalytic effect of the nanoparticles by reducing the asphaltenes content and the 620 °C+ residue 40% and 47%, respectively. Also, rheological measurements showed that the viscosity decreased by up to 85% (one order of magnitude after the nanofluid treatment during the steam injection process.

Age dependency of myocardial triglyceride content. A 3T high-field {sup 1}H-MR spectroscopy study

Energy Technology Data Exchange (ETDEWEB)

Petritsch, B.; Gassenmaier, T.; Kunz, A.S.; Donhauser, J.; Bley, T.A.; Horn, M. [University Hospital of Wuerzburg (Germany). Inst. of Diagnostic and Interventional Radiology; Goltz, J.P. [University Hospital of Schleswig-Holstein, Campus Luebeck (Germany). Clinic for Radiology and Nuclear Medicine

2015-11-15

The role of myocardial triglyceride (mTG) content in the aging human heart is not entirely understood. The aim of this study was to measure concentrations of mTG content from healthy volunteers and to determine the association between age, mTG content and systolic heart function. Furthermore, the technical stability of the {sup 1}H-magnetic resonance spectroscopy ({sup 1}H-MRS) and the reliability of peak evaluation at 3 T were evaluated. The total study population of 47 healthy volunteers was divided into 4 age classes, according to the age of the subjects (1{sup st} cohort 20-29 years (yrs.), n=20; 2{sup nd} cohort 30-39 yrs., n=10; 3{sup rd} cohort 40-49 yrs., n=9; 4{sup th} cohort 50-60 yrs., n=8). Cardiac MRI and double triggered {sup 1}H-MRS of the myocardium were consecutively performed using a 3 T scanner. Each participant underwent spectroscopic measurements twice in the same investigation. mTG content increases with age. The correlation of age and mTG is minimal (r=0.48; p<0.001). The following age-averaged mTG content values expressed as % of mTG signal compared to the water signal were determined for each cohort: 1{sup st} cohort 0.25 % (± 0.17); 2{sup nd} cohort 0.48 % (± 0.30); 3{sup rd} cohort 0.48 % (± 0.18); 4{sup th} cohort 0.77 % (± 0.70). There was no significant correlation (r=0.04; p=n.s.) between LV mass and mTG content in healthy volunteers. Within our cohorts, no effects of age or mTG content on systolic heart function were seen (r=-0.01; p=n.s.). The intraclass correlation coefficient of spectroscopic measurements was high (r=0.965; p<0.001). Myocardial TG content increases with age. The normal age-dependent concentration ranges of myocardial lipid metabolites reported in this study may be helpful for the correction of acquired {sup 1}H-MRS data in patients when evaluating metabolic and cardiovascular diseases in future magnetic resonance spectroscopy studies.

Use of adsorption and gas chromatographic techniques in estimating biodegradation of indigenous crude oils

International Nuclear Information System (INIS)

Kokub, D.; Allahi, A.; Shafeeq, M.; Khalid, Z.M.; Malik, K.A.; Hussain, A.

1993-01-01

Indigenous crude oils could be degraded and emulsified upto varying degree by locally isolated bacteria. Degradation and emulsification was found to be dependent upon the chemical composition of the crude oils. Tando Alum and Khashkheli crude oils were emulsified in 27 and 33 days of incubation respectively. While Joyamair crude oil and not emulsify even mainly due to high viscosity of this oil. Using adsorption chromatographic technique, oil from control (uninoculated) and bio degraded flasks was fractioned into the deasphaltened oil containing saturate, aromatic, NSO (nitrogen, sulphur, oxygen) containing hydrocarbons) and soluble asphaltenes. Saturate fractions from control and degraded oil were further analysed by gas liquid chromatography. From these analyses, it was observed that saturate fraction was preferentially utilized and the crude oils having greater contents of saturate fraction were better emulsified than those low in this fraction. Utilization of various fractions of crude oils was in the order saturate> aromatic> NSO. (author)

The potential applications in heavy oil EOR with the nanoparticle and surfactant stabilized solvent-based emulsion

Energy Technology Data Exchange (ETDEWEB)

Qiu, F. [Texas A and M Univ., College Station, TX (United States)

2010-07-01

The main challenges in developing the heavy oil reservoirs in the Alaska North Slope (ANS) include technical challenges regarding thermal recovery; sand control and disposal; high asphaltene content; and low in-situ permeability. A chemical enhanced oil recovery method may be possible for these reservoirs. Solvent based emulsion flooding provides mobility control; oil viscosity reduction; and in-situ emulsification of heavy oil. This study evaluated the potential application of nano-particle-stabilized solvent based emulsion injection to enhance heavy oil recovery in the ANS. The optimized micro-emulsion composition was determined using laboratory tests such as phase behaviour scanning, rheology studies and interfacial tension measurements. The optimized nano-emulsions were used in core flooding experiments to verify the recovery efficiency. The study revealed that the potential use of this kind of emulsion flooding is a promising enhanced oil recovery process for some heavy oil reservoirs in Alaska, Canada and Venezuela. 4 refs., 2 tabs., 10 figs.

Iron content and solubility in dust from high-alpine snow along a north-south transect of High Asia

Directory of Open Access Journals (Sweden)

Guangjian Wu

2012-04-01

Full Text Available This study describes the dissolved and insoluble iron fraction of dust (mineral aerosol in high-alpine snow samples collected along a north-south transect across High Asia (Eastern Tien Shan, Qilian Shan, and Southern Tibetan Plateau. This dust provides the basic chemical properties of mid- and high-level tropospheric Asian dust that can supply the limiting iron nutrient for phytoplankton growth in the North Pacific. The iron content in Asian dust averages 4.95% in Eastern Tien Shan, 3.38–5.41% along Qilian Shan and 3.85% in the Southern Tibetan Plateau. The iron fractional solubility averages about 0.25% in Eastern Tien Shan, 0.05–2% along Qilian Shan and 1.5% in the Southern Tibetan Plateau. Among the controlling factors that can affect iron solubility in Asian dust, such as dust composition and particle grain size, acidity seems to be the most significant and can increase the iron solubility by one or two orders of magnitude with acidification of pH=0.66. Our results reveal that iron solubility of dust in the remote downwind sites is higher than that in high-alpine snow, confirming the strong pH-dependence of iron solubility, and indicating that Asian dust shows a large variation in iron solubility on a regional scale.

Step-by-step guide to building an inexpensive 3D printed motorized positioning stage for automated high-content screening microscopy.

Science.gov (United States)

Schneidereit, Dominik; Kraus, Larissa; Meier, Jochen C; Friedrich, Oliver; Gilbert, Daniel F

2017-06-15

High-content screening microscopy relies on automation infrastructure that is typically proprietary, non-customizable, costly and requires a high level of skill to use and maintain. The increasing availability of rapid prototyping technology makes it possible to quickly engineer alternatives to conventional automation infrastructure that are low-cost and user-friendly. Here, we describe a 3D printed inexpensive open source and scalable motorized positioning stage for automated high-content screening microscopy and provide detailed step-by-step instructions to re-building the device, including a comprehensive parts list, 3D design files in STEP (Standard for the Exchange of Product model data) and STL (Standard Tessellation Language) format, electronic circuits and wiring diagrams as well as software code. System assembly including 3D printing requires approx. 30h. The fully assembled device is light-weight (1.1kg), small (33×20×8cm) and extremely low-cost (approx. EUR 250). We describe positioning characteristics of the stage, including spatial resolution, accuracy and repeatability, compare imaging data generated with our device to data obtained using a commercially available microplate reader, demonstrate its suitability to high-content microscopy in 96-well high-throughput screening format and validate its applicability to automated functional Cl - - and Ca 2+ -imaging with recombinant HEK293 cells as a model system. A time-lapse video of the stage during operation and as part of a custom assembled screening robot can be found at https://vimeo.com/158813199. Copyright © 2016 The Authors. Published by Elsevier B.V. All rights reserved.

Computers in the investigation of the impurity content of high-purity materials

International Nuclear Information System (INIS)

Makarov, Yu.B.; Yan'kov, S.V.

1987-01-01

The efficiency of the concept of data banks for the accumulation and processing of information is now generally acknowledged. In scientific investigations not only bibliographic but also factual data banks are becoming more and more prevalent. In this article, the authors consider the possibilities of providing a data bank on high-purity materials for the study of impurity contents. Also in this paper, the authors distinguish the following groups of problems that arise in the study of impurity composition and presents examples of their proposed solutions to these problems: the analysis of error and the determination of the most probably value of impurity concentration; the estimation of average properties of impurity composition with respect to groups of impurities and samples, and the forecast of the complete impurity composition

High-content live cell imaging with RNA probes: advancements in high-throughput antimalarial drug discovery

Directory of Open Access Journals (Sweden)

Cervantes Serena

2009-06-01

Full Text Available Abstract Background Malaria, a major public health issue in developing nations, is responsible for more than one million deaths a year. The most lethal species, Plasmodium falciparum, causes up to 90% of fatalities. Drug resistant strains to common therapies have emerged worldwide and recent artemisinin-based combination therapy failures hasten the need for new antimalarial drugs. Discovering novel compounds to be used as antimalarials is expedited by the use of a high-throughput screen (HTS to detect parasite growth and proliferation. Fluorescent dyes that bind to DNA have replaced expensive traditional radioisotope incorporation for HTS growth assays, but do not give additional information regarding the parasite stage affected by the drug and a better indication of the drug's mode of action. Live cell imaging with RNA dyes, which correlates with cell growth and proliferation, has been limited by the availability of successful commercial dyes. Results After screening a library of newly synthesized stryrl dyes, we discovered three RNA binding dyes that provide morphological details of live parasites. Utilizing an inverted confocal imaging platform, live cell imaging of parasites increases parasite detection, improves the spatial and temporal resolution of the parasite under drug treatments, and can resolve morphological changes in individual cells. Conclusion This simple one-step technique is suitable for automation in a microplate format for novel antimalarial compound HTS. We have developed a new P. falciparum RNA high-content imaging growth inhibition assay that is robust with time and energy efficiency.

Characterization of oil and gas reservoir heterogeneity. Annual report, November 1, 1990--October 31, 1991

Energy Technology Data Exchange (ETDEWEB)

1991-12-31

The objective of the cooperative research program is to characterize Alaskan reservoirs in terms of their reserves, physical and chemical properties, geologic configuration and structure, and the development potential. The tasks completed during this period include: (1) geologic reservoir description of Endicott Field; (2) petrographic characterization of core samples taken from selected stratigraphic horizons of the West Sak and Ugnu (Brookian) wells; (3) development of a polydispersed thermodynamic model for predicting asphaltene equilibria and asphaltene precipitation from crude oil-solvent mixtures, and (4) preliminary geologic description of the Milne Point Unit.

Characterization of oil and gas reservoir heterogeneity

Energy Technology Data Exchange (ETDEWEB)

1991-01-01

The objective of the cooperative research program is to characterize Alaskan reservoirs in terms of their reserves, physical and chemical properties, geologic configuration and structure, and the development potential. The tasks completed during this period include: (1) geologic reservoir description of Endicott Field; (2) petrographic characterization of core samples taken from selected stratigraphic horizons of the West Sak and Ugnu (Brookian) wells; (3) development of a polydispersed thermodynamic model for predicting asphaltene equilibria and asphaltene precipitation from crude oil-solvent mixtures, and (4) preliminary geologic description of the Milne Point Unit.

Effects of hot rolling and titanium content on the microstructure and mechanical properties of high boron Fe–B alloys

International Nuclear Information System (INIS)

He, Lin; Liu, Ying; Li, Jun; Li, Binghong

2012-01-01

Highlights: ► The content of B is 1.8 wt.% in the high boron Fe–B alloys. ► Hot-rolling improves the mechanical properties, especially the elongation. ► The Ti content affects the microstructure and mechanical properties. ► Eutectic boride can be eliminated when the atomic ratio of Ti/B is no less than 0.5. ► Alloy exhibits balanced mechanical properties when the atomic ratio of Ti/B is 0.5. -- Abstract: High boron Fe–B alloys (1.8 wt.% B) with different titanium contents are fabricated by Vacuum Induction Melting (VIM) technique. The integrated mechanical properties of the as-cast alloys are poor, especially the ductility. In this investigation, hot-rolling technology is used to improve the microstructure and mechanical properties. The microstructure analysis shows that hot rolling can reduce the size and improve the distribution of the reinforcements. The mechanical properties testing indicates that the yield strength is unchanged basically, but the tensile strength and elongation are improved greatly by hot rolling, especially the elongation. The content of titanium also has great effects on the microstructures and mechanical properties of the hot-rolled alloys. For the hot-rolled alloys, with the titanium content increasing, the ultimate tensile strength and yield strength first decrease slightly and then increase. The elongation and impact toughness are improved significantly. In particular, when the atomic ratio of Ti to B is 0.5, the reinforcements are almost entirely TiB 2 and uniformly distributed in the Fe-matrix. The ternary Fe–B–Ti alloy exhibits balanced mechanical properties: yield strength, ultimate tensile strength, elongation and impact toughness are 334 MPa, 602 MPa, 16.2% and 213 kJ/m 2 , respectively.

High nitrogen availability reduces polyphenol content in Sphagnum peat.

Science.gov (United States)

Bragazza, Luca; Freeman, Chris

2007-05-15

Peat mosses of the genus Sphagnum constitute the bulk of living and dead biomass in bogs. These plants contain peculiar polyphenols which hamper litter peat decomposition through their inhibitory activity on microbial breakdown. In the light of the increasing availability of biologically active nitrogen in natural ecosystems, litter derived from Sphagnum mosses is an ideal substrate to test the potential effects of increased atmospheric nitrogen deposition on polyphenol content in litter peat. To this aim, we measured total nitrogen and soluble polyphenol concentration in Sphagnum litter peat collected in 11 European bogs under a chronic gradient of atmospheric nitrogen deposition. Our results demonstrate that increasing nitrogen concentration in Sphagnum litter, as a consequence of increased exogenous nitrogen availability, is accompanied by a decreasing concentration of polyphenols. This inverse relationship is consistent with reports that in Sphagnum mosses, polyphenol and protein biosynthesis compete for the same precursor. Our observation of modified Sphagnum litter chemistry under chronic nitrogen eutrophication has implications in the context of the global carbon balance, because a lower content of decay-inhibiting polyphenols would accelerate litter peat decomposition.

Understanding a High School Physics Teacher's Pedagogical Content Knowledge of Argumentation

Science.gov (United States)

Wang, Jianlan; Buck, Gayle A.

2016-08-01

Scientific argumentation is an important learning objective in science education. It is also an effective instructional approach to constructivist science learning. The implementation of argumentation in school settings requires science teachers, who are pivotal agents of transforming classroom practices, to develop sophisticated knowledge of argumentation. However, there is a lack of understanding about science teachers' knowledge of argumentation, especially the dialogic meaning of argumentation. In this case study, we closely examine a high school physics teacher's argumentation-related pedagogic content knowledge (PCK) in the context of dialogic argumentation. We synthesize the teacher's performed PCK from his argumentation practices and narrated PCK from his reflection on the argumentation practices, from which we summarize his PCK of argumentation from the perspectives of orientation, instructional strategies, students, curriculum, and assessment. Finally, we describe the teacher's perception and adaption of argumentation in his class. We also identity the barriers to argumentation implementation in this particular case and suggest solutions to overcome these barriers.

STUDIES ON HIGH SOLID CONTENT AND STABLE EMULSIFIER—FREE EMULSION POLYMERIZATION

Institute of Scientific and Technical Information of China (English)

TangGuangliang; HaoGuangjie; 等

1998-01-01

In this article,AHPS(3-allyloxy-2-hydroxy-1-propanesulfonate salt) was synthesized to use in emulsifier-free emulsion polymerization of BA/BMA/MMA system for high solid content latexes.Storage stability,flow behavior of the latexes,morphology of the obtained latex particles,dynamic viscoelastic behavior,tensile strength and water resistance properties of the resulted copolymers were investigated.The experimental results show that with the addition of AHPS,stability of the emulsion is greatly improved that there appears no apparent precipitation during the polymerization and storage at room temperature for 6 months and at -10℃ for four months.Flow of the latexes follows the Bingham body laws,diameter of the latex particles is about 0.6μm,of which is larger than that of by conventional emulsion polymerization(0.12μm).In addition,not only water resistance of the copolymers obtained by emulsifier-free emulstion polymerization is greatly improved,but also tensile strength is obviously enhanced.

CellProfiler and KNIME: open source tools for high content screening.

Science.gov (United States)

Stöter, Martin; Niederlein, Antje; Barsacchi, Rico; Meyenhofer, Felix; Brandl, Holger; Bickle, Marc

2013-01-01

High content screening (HCS) has established itself in the world of the pharmaceutical industry as an essential tool for drug discovery and drug development. HCS is currently starting to enter the academic world and might become a widely used technology. Given the diversity of problems tackled in academic research, HCS could experience some profound changes in the future, mainly with more imaging modalities and smart microscopes being developed. One of the limitations in the establishment of HCS in academia is flexibility and cost. Flexibility is important to be able to adapt the HCS setup to accommodate the multiple different assays typical of academia. Many cost factors cannot be avoided, but the costs of the software packages necessary to analyze large datasets can be reduced by using Open Source software. We present and discuss the Open Source software CellProfiler for image analysis and KNIME for data analysis and data mining that provide software solutions which increase flexibility and keep costs low.

Monitoring water content in Opalinus Clay within the FE-Experiment: Test application of dielectric water content sensors

Science.gov (United States)

Sakaki, T.; Vogt, T.; Komatsu, M.; Müller, H. R.

2013-12-01

The spatiotemporal variation of water content in the near field rock around repository tunnels for radioactive waste in clay formations is one of the essential quantities to be monitored for safety assessment in many waste disposal programs. Reliable measurements of water content are important not only for the understanding and prediction of coupled hydraulic-mechanic processes that occur during tunnel construction and ventilation phase, but also for the understanding of coupled thermal-hydraulic-mechanical (THM) processes that take place in the host rock during the post closure phase of a repository tunnel for spent fuel and high level radioactive waste (SF/HLW). The host rock of the Swiss disposal concept for SF/HLW is the Opalinus Clay formation (age of approx. 175 Million years). To better understand the THM effects in a full-scale heater-engineered barrier-rock system in Opalinus Clay, a full-scale heater test, namely the Full-Scale Emplacement (FE) experiment, was initiated in 2010 at the Mont Terri underground rock laboratory in north-western Switzerland. The experiment is designed to simulate the THM evolution of a SF/HLW repository tunnel based on the Swiss disposal concept in a realistic manner during the construction, emplacement, backfilling, and post-closure phases. The entire experiment implementation (in a 50 m long gallery with approx. 3 m diameter) as well as the post-closure THM evolution will be monitored using a network of several hundred sensors. The sensors will be distributed in the host rock, the tunnel lining, the engineered barrier, which consists of bentonite pellets and blocks, and on the heaters. The excavation is completed and the tunnel is currently being ventilated. Measuring water content in partially saturated clay-rich high-salinity rock with a deformable grain skeleton is challenging. Therefore, we use the ventilation phase (before backfilling and heating) to examine the applicability of commercial water content sensors and to

Improving fuel quality by whole crude oil hydrotreating: A kinetic model for hydrodeasphaltenization in a trickle bed reactor