WorldWideScience

Sample records for high ammonium levels

  1. Elevated ammonium levels

    DEFF Research Database (Denmark)

    Søgaard, Rikke; Novak, Ivana; MacAulay, Nanna

    2012-01-01

    ]glutamate uptake and glutamate transport currents but had no effect on EAAT2. The maximal EAAT3-mediated glutamate transport current was increased but the apparent affinities for glutamate and Na(+) were unaltered. Ammonium did not affect EAAT3-mediated transient currents, indicating that EAAT3 surface expression...... was not enhanced. The ammonium-induced stimulation of EAAT3 increased with increasing extracellular pH, suggesting that the gaseous form NH(3) mediates the effect. An ammonium-induced intracellular alkalinization was excluded as the cause of the enhanced EAAT3 activity because 1) ammonium acidified the oocyte...... cytoplasm, 2) intracellular pH buffering with MOPS did not reduce the stimulation, and 3) ammonium enhanced pH-independent cysteine transport. Our data suggest that the ammonium-elicited uptake stimulation is not caused by intracellular alkalinization or changes in the concentrations of cotransported ions...

  2. [Reasons of high concentration ammonium in Yellow River, China].

    Science.gov (United States)

    Zhang, Xue-qing; Xia, Xing-hui; Yang, Zhi-feng

    2007-07-01

    Ammonium nitrogen contamination is one of the major problems of the Yellow River in China. The speciation, concentration and sources of nitrogen compounds as well as the water environment conditions of the Yellow River had been analyzed to study the reasons for the fact that the ammonium nitrogen concentration was above the water quality standard. In addition, laboratory experiments had been carried out to investigate the effects of suspended sediment (SS) on nitrification rate. The results indicated that the presence of SS could accelerate the nitrification process, therefore, the effects of SS on nitrification rate was not the reason for the high level of ammonium nitrogen in the river. The excessive and continuous input of nitrogen contaminants to the river was the fundamental reason for the high concentration of ammonium nitrogen. Organic and ammonium nitrogen with high concentration inhibitted the nitrification processes. When the initial NH4+ -N concentrations were 10.1, 18.4 and 28.2 mg/L, nitrification efficiencies were 17.4%, 13.0% and 2.5%, respectively. When the initial organic nitrogen concentrations were 5.5 and 8.6 mg/L, the maximum concentrations of ammonium nitrogen produced by the oxidation of organic nitrogen would reach 0.47 and 1.69 mg/L and they would last for 2 days and 6 days, respectively. The oxygen-consuming organics and toxic substance existing in the river water could inhibit the activity of nitrifying bacteria, and thus lead to the accumulation of ammonium nitrogen. In addition, the high pH value of river water resulted in the high concentration of nonionic ammonium nitrogen which would reduce the activity of nitrifying bacteria and decrease the nitrification rates. Besides, low river runoff, low SS content and low activity of nitrifying bacteria resulted in the high level of ammonium nitrogen of the river in the low water season.

  3. Effects of ammonium concentration and charge exchange on ammonium recovery from high strength wastewater using a microbial fuel cell

    NARCIS (Netherlands)

    Kuntke, P.; Geleij, M.; Bruning, H.; Zeeman, G.; Hamelers, H.V.M.; Buisman, C.J.N.

    2011-01-01

    Ammonium recovery using a 2 chamber microbial fuel cell (MFC) was investigated at high ammonium concentration. Increasing the ammonium concentration (from 0.07 g to 4 g ammonium-nitrogen/L) by addition of ammonium chloride did not affect the performance of the MFC. The obtained current densities by

  4. Effects of High Ammonium Concentration on Growth and Nutrient Uptake of Lettuce Plants with Solution Culture

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    A nutrition solution experiment was conducted over two months to investigate the response of vegetable crops to high concentrations of ammonium, using lettuce (Lactuca sativa L. cv. Angustana Irish) as a test crop. Ammonium concentrations were designed in 5 levels, ranging from 12 mmol N L-1 to 22 mmol N L-1 and local tap water was used as water source. At the first culture stage (0-9 days), lettuce plants maintained normal growth while the lettuce roots were increasingly impaired. During the subsequent three stages the root structure was greatly damaged, and roots became brown or black through continuous supply of high concentration of ammonium. However, there was no obvious reduction of the aboveground biomass of the plants in the high ammonium treatments compared to those supplied with nitrate alone. In contrast to results obtained in another experiment from us with distilled water, the detrimental effect of high ammonium concentration on lettuce growth was greatly alleviated. Based on the results, it was postulated that the small amount of nitrate and the higher amount of bicarbonate existed in the tap water might mitigate the adverse effects of high ammonium N. The higher bicarbonate content in water and soil has usually been regarded as a major constraint factor limiting plant growth in calcareous soil areas. However, the reaction of bicarbonate to ammonium might produce positively interactive effect on reduction of both damages. The lettuce plants grown in ammonium solutions took up less P, K, Fe, Mn and Cu and more Ca than those grown in the nitrate nutrient solution. In conclusion, the results indicated that the N form imposed an obvious influence on absorption of cations and anions. Supplying ammonium-N stimulated transport of Ca, Mg and Mn to shoots of lettuce.

  5. A nitrogen-dependent switch in the high affinity ammonium transport in Medicago truncatula.

    Science.gov (United States)

    Straub, Daniel; Ludewig, Uwe; Neuhäuser, Benjamin

    2014-11-01

    Ammonium transporters (AMTs) are crucial for the high affinity primary uptake and translocation of ammonium in plants. In the model legume Medicago truncatula, the genomic set of AMT-type ammonium transporters comprises eight members. Only four genes were abundantly expressed in young seedlings, both in roots and shoots. While the expression of all AMTs in the shoot was not affected by the nitrogen availability, the dominating MtAMT1;1 gene was repressed by nitrogen in roots, despite that cellular nitrogen concentrations were far above deficiency levels. A contrasting de-repression by nitrogen was observed for MtAMT1;4 and MtAMT2;1, which were both expressed at intermediate level. Weak expression was found for MtAMT1;2 and MtAMT2;3, while the other AMTs were not detected in young seedlings. When expressed from their endogenous promoters, translational fusion proteins of MtAMT1;1 and MtAMT2;1 with green fluorescent protein were co-localized in the plasma membrane of rhizodermal cells, but also detected in cortical root layers. Both transporter proteins similarly functionally complemented a yeast strain that is deficient in high affinity ammonium transport, both at acidic and neutral pH. The uptake into yeast mediated by these transporters saturated with Km AMT1;1 = 89 µM and Km AMT2;1 = 123 µM, respectively. When expressed in oocytes, MtAMT1;1 mediated much larger (15)N-ammonium uptake than MtAMT2;1, but NH4 (+) currents were only recorded for MtAMT1;1. These currents saturated with a voltage-dependent Km = 90 µM at -80 mV. The cellular localization and regulation of the AMTs suggests that MtAMT1;1 encodes the major high affinity ammonium transporter gene in low nitrogen grown young M. truncatula roots and despite the similar localization and substrate affinity, MtAMT2;1 appears functionally distinct and more important at higher nitrogen supply.

  6. Highly efficient hydrogen storage system based on ammonium bicarbonate/formate redox equilibrium over palladium nanocatalysts.

    Science.gov (United States)

    Su, Ji; Yang, Lisha; Lu, Mi; Lin, Hongfei

    2015-03-01

    A highly efficient, reversible hydrogen storage-evolution process has been developed based on the ammonium bicarbonate/formate redox equilibrium over the same carbon-supported palladium nanocatalyst. This heterogeneously catalyzed hydrogen storage system is comparable to the counterpart homogeneous systems and has shown fast reaction kinetics of both the hydrogenation of ammonium bicarbonate and the dehydrogenation of ammonium formate under mild operating conditions. By adjusting temperature and pressure, the extent of hydrogen storage and evolution can be well controlled in the same catalytic system. Moreover, the hydrogen storage system based on aqueous-phase ammonium formate is advantageous owing to its high volumetric energy density.

  7. High Pressure Burn Rate Measurements on an Ammonium Perchlorate Propellant

    Energy Technology Data Exchange (ETDEWEB)

    Glascoe, E A; Tan, N

    2010-04-21

    High pressure deflagration rate measurements of a unique ammonium perchlorate (AP) based propellant are required to design the base burn motor for a Raytheon weapon system. The results of these deflagration rate measurements will be key in assessing safety and performance of the system. In particular, the system may experience transient pressures on the order of 100's of MPa (10's kPSI). Previous studies on similar AP based materials demonstrate that low pressure (e.g. P < 10 MPa or 1500 PSI) burn rates can be quite different than the elevated pressure deflagration rate measurements (see References and HPP results discussed herein), hence elevated pressure measurements are necessary in order understand the deflagration behavior under relevant conditions. Previous work on explosives have shown that at 100's of MPa some explosives will transition from a laminar burn mechanism to a convective burn mechanism in a process termed deconsolidative burning. The resulting burn rates that are orders-of-magnitude faster than the laminar burn rates. Materials that transition to the deconsolidative-convective burn mechanism at elevated pressures have been shown to be considerably more violent in confined heating experiments (i.e. cook-off scenarios). The mechanisms of propellant and explosive deflagration are extremely complex and include both chemical, and mechanical processes, hence predicting the behavior and rate of a novel material or formulation is difficult if not impossible. In this work, the AP/HTPB based material, TAL-1503 (B-2049), was burned in a constant volume apparatus in argon up to 300 MPa (ca. 44 kPSI). The burn rate and pressure were measured in-situ and used to calculate a pressure dependent burn rate. In general, the material appears to burn in a laminar fashion at these elevated pressures. The experiment was reproduced multiple times and the burn rate law using the best data is B = (0.6 {+-} 0.1) x P{sup (1.05{+-}0.02)} where B is the burn

  8. Ammonium Chloride Ingestion Attenuates Exercise-Induced mRNA Levels in Human Muscle.

    Directory of Open Access Journals (Sweden)

    Johann Edge

    Full Text Available Minimizing the decrease in intracellular pH during high-intensity exercise training promotes greater improvements in mitochondrial respiration. This raises the intriguing hypothesis that pH may affect the exercise-induced transcription of genes that regulate mitochondrial biogenesis. Eight males performed 10x2-min cycle intervals at 80% VO2speak intensity on two occasions separated by ~2 weeks. Participants ingested either ammonium chloride (ACID or calcium carbonate (PLA the day before and on the day of the exercise trial in a randomized, counterbalanced order, using a crossover design. Biopsies were taken from the vastus lateralis muscle before and after exercise. The mRNA level of peroxisome proliferator-activated receptor co-activator 1α (PGC-1α, citrate synthase, cytochome c and FOXO1 was elevated at rest following ACID (P0.05; the difference in PGC-1α mRNA content 2 h post-exercise between ACID and PLA was not significant (P = 0.08. Thus, metabolic acidosis abolished the early post-exercise increase of PGC-1α mRNA and the mRNA of downstream mitochondrial and glucose-regulating proteins. These findings indicate that metabolic acidosis may affect mitochondrial biogenesis, with divergent responses in resting and post-exercise skeletal muscle.

  9. Leveling effects of ammonium salts on thermal stabilities of polyethylene glycols.

    Science.gov (United States)

    Xia, Juan; Song, Le Xin; Liu, Wei; Teng, Yue

    2013-10-28

    In this work, the thermal stabilities of a series of polyethylene glycols (PEG 4000, 6000 and 10000) were investigated after compositing with different kinds of inorganic salts, such as ammonium molybdate tetrahydrate (AMT), NH4VO3, (NH4)2SO4, NH4NO3, Na2SO4, Na2MoO4. It was first observed that all the ammonium salts exerted leveling effects for the thermal stabilities of the PEGs. In other words, the presence of the ammonium salts caused the occurrence of the maximum decomposition rates of the PEGs with the same repeat sequence but different chain lengths at almost the same temperatures. Leveling effects were defined by three parameters: leveling spans, leveling degrees and dispersion degrees of leveling. Further experiments revealed that leveling effects also occur in similar types of polymers: polypropylene glycols (PPG 2000, 3000 and 4000). A series of independent experiments including Fourier transformation infrared spectroscopy, Raman spectroscopy, differential scanning calorimetry, time-of-flight mass spectrometry, conductivity and field-emission scanning electron microscopy were performed to explore the origin of leveling effects. We consider that the interaction between inorganic ions and polymer molecules and the Hofmeister effect of ions in solution are two important factors affecting the stability of salt–polymer composites, because they can contribute to decrease the interaction between the polymer chains, leading to changes in the conformation and pyrolysis mode of polymers. We believe that the finding of leveling effects would be significant for both basic and applied research of soft matter.

  10. Adjusting ammonium uptake via phosphorylation.

    Science.gov (United States)

    Lanquar, Viviane; Frommer, Wolf B

    2010-06-01

    In plants, AMT/MEP/Rh superfamily mediates high affinity ammonium uptake. AMT/MEP transporters form a trimeric complex, which requires a productive interaction between subunits in order to be functional. The AMT/MEP C-terminal domain is highly conserved in more than 700 AMT homologs from cyanobacteria to higher plants with no cases found to be lacking this domain. AMT1;1 exists in active and inactive states, probably controlled by the spatial positioning of the C-terminus. Ammonium triggers the phosphorylation of a conserved threonine residue (T460) in the C-terminus of AMT1;1 in a time- and concentration-dependent manner. The T460 phosphorylation level correlates with a decrease of root ammonium uptake. We propose that ammonium-induced phosphorylation modulates ammonium uptake as a general mechanism to protect against ammonium toxicity.

  11. The relationship between the violet pigment PP-V production and intracellular ammonium level in Penicillium purpurogenum.

    Science.gov (United States)

    Kojima, Ryo; Arai, Teppei; Matsufuji, Hiroshi; Kasumi, Takafumi; Watanabe, Taisuke; Ogihara, Jun

    2016-12-01

    Penicillium purpurogenum is the fungus that produces an azaphilone pigment. However, details about the pigment biosynthesis pathway are unknown. The violet pigment PP-V is the one of the main pigments biosynthesized by this fungus. This pigment contains an amino group in a pyran ring as its core structure. We focused on this pigment and examined the relationship between intracellular ammonium concentration and pigment production using glutamine as a nitrogen source. The intracellular ammonium level decreased about 1.5-fold in conditions favoring PP-V production. Moreover, P. purpurogenum was transferred to medium in which it commonly produces the related pigment PP-O after cultivating it in the presence or absence of glutamine to investigate whether this fungus biosynthesizes PP-V using surplus ammonium in cells. Only mycelia cultured in medium containing 10 mM glutamine produced the violet pigment, and simultaneously intracellular ammonium levels decreased under this condition. From comparisons of the amount of PP-V that was secreted with quantity of surplus intracellular ammonium, it is suggested that P. purpurogenum maintains ammonium homeostasis by excreting waste ammonium as PP-V.

  12. Biomass burning in eastern Europe during spring 2006 caused high deposition of ammonium in northern Fennoscandia

    DEFF Research Database (Denmark)

    Karlsson, Per Erik; Ferm, Martin; Pihl Karlsson, Gunilla

    2013-01-01

    High air concentrations of ammonium were detected at low and high altitude sites in Sweden, Finland and Norway during the spring 2006, coinciding with polluted air from biomass burning in eastern Europe passing over central and northern Fennoscandia. Unusually high values for throughfall deposition...

  13. Effect of ammonium concentration on alcoholic fermentation kinetics by wine yeasts for high sugar content.

    Science.gov (United States)

    Taillandier, Patricia; Ramon Portugal, Felipe; Fuster, André; Strehaiano, Pierre

    2007-02-01

    Kinetics of alcoholic fermentation by Saccharomyces cerevisiae wine strains in a synthetic medium with high sugar content were established for different nitrogen initial content and are presented for four strains. The composition of the medium was close to grape must except that the nitrogen source consisted mainly in ammonium and was varied from 120 to 290 mg N/l assimilable nitrogen. The overall nitrogen consumed was also estimated in order to determine nitrogen requirement variability. The effect of assimilable nitrogen was in general greater on sugar consumption rates than on growth and three kinds of effect on sugar consumption rates were observed: (i) existence of an optimal initial nitrogen level for a maximal sugar consumption rate (inhibition if excess), (ii) no effect of nitrogen beyond the intermediary level (saturation), (iii) sugar consumption rate proportional to the initial nitrogen level (activation). In all cases, the amount of consumed nitrogen increased with its initial concentration and so did the fructophilic capacity of the strains. The optimal requirement varied from 0.62 to 0.91 mg N/g of sugars according to different strains. There was no general correlation between the sugar assimilation rates and the nitrogen requirement.

  14. Growth and Chlorophyll Content of Canola Plants Supplied with Urea and Ammonium Nitrate in Response to Various Nickel Levels

    OpenAIRE

    BYBORDI, Ahmad; Mohammad Nabi GHEIBI

    2009-01-01

    Both the beneficial and the adverse effects of various nickel level supplements on growth and chlorophyll content of canola plants were evaluated while either urea or ammonium nitrate was supplied as the sole N source in the nutrient solutions. This study was arranged in completely randomized with three replications. Treatments included nutrient solution cultures containing urea and ammonium nitrate at the rate of 84 mg N L-1 separately as nitrogen sources with four nickel levels as NiSO4.6H2...

  15. Ectomycorrhiza-mediated repression of the high-affinity ammonium importer gene AmAMT2 in Amanita muscaria.

    Science.gov (United States)

    Willmann, Anita; Weiss, Michael; Nehls, Uwe

    2007-02-01

    A main function of ectomycorrhizas, a symbiosis between certain soil fungi and fine roots of woody plants, is the exchange of plant-derived carbohydrates for fungus-derived nutrients. As it is required in large amounts, nitrogen is of special interest. A gene (AmAMT2) coding for a putative fungal ammonium importer was identified in an EST project of functional Amanita muscaria/poplar ectomycorrhizas. Heterologous expression of the entire AmAMT2 coding region in yeast revealed the corresponding protein to be a high-affinity ammonium importer. In axenically grown Amanita hyphae AmAMT2 expression was strongly repressed by nitrogen, independent of whether the offered nitrogen source was transported by AmAMT2 or not. In functional ectomycorrhizas the AmAMT2 transcript level was further decreased in both hyphal networks (sheath and Hartig net), while extraradical hyphae revealed strong gene expression. Together our data suggest that (1) AmAMT2 expression is regulated by the endogenous nitrogen content of hyphae and (2) fungal hyphae in ectomycorrhizas are well supported with nitrogen even when the extraradical mycelium is nitrogen limited. As a consequence of AmAMT2 repression in mycorrhizas, ammonium can be suggested as a potential nitrogen source delivered by fungal hyphae in symbiosis.

  16. High pressure structural, elastic and vibrational properties of green energetic oxidizer ammonium dinitramide

    Science.gov (United States)

    Yedukondalu, N.; Ghule, Vikas D.; Vaitheeswaran, G.

    2016-08-01

    Ammonium DiNitramide (ADN) is one of the most promising green energetic oxidizers for future rocket propellant formulations. In the present work, we report a detailed theoretical study on structural, elastic, and vibrational properties of the emerging oxidizer under hydrostatic compression using various dispersion correction methods to capture weak intermolecular (van der Waals and hydrogen bonding) interactions. The calculated ground state lattice parameters, axial compressibilities, and equation of state are in good accord with the available experimental results. Strength of intermolecular interactions has been correlated using the calculated compressibility curves and elastic moduli. Apart from this, we also observe discontinuities in the structural parameters and elastic constants as a function of pressure. Pictorial representation and quantification of intermolecular interactions are described by the 3D Hirshfeld surfaces and 2D finger print maps. In addition, the computed infra-red (IR) spectra at ambient pressure reveal that ADN is found to have more hygroscopic nature over Ammonium Perchlorate (AP) due to the presence of strong hydrogen bonding. Pressure dependent IR spectra show blue- and red-shift of bending and stretching frequencies which leads to weakening and strengthening of the hydrogen bonding below and above 5 GPa, respectively. The abrupt changes in the calculated structural, mechanical, and IR spectra suggest that ADN might undergo a first order structural transformation to a high pressure phase around 5-6 GPa. From the predicted detonation properties, ADN is found to have high and low performance characteristics (DCJ = 8.09 km/s and PCJ = 25.54 GPa) when compared with ammonium based energetic oxidizers (DCJ = 6.50 km/s and PCJ = 17.64 GPa for AP, DCJ = 7.28 km/s and PCJ = 18.71 GPa for ammonium nitrate) and well-known secondary explosives for which DCJ = ˜8-10 km/s and PCJ = ˜30-50 GPa, respectively.

  17. Hierarchical one-dimensional ammonium nickel phosphate microrods for high-performance pseudocapacitors

    CSIR Research Space (South Africa)

    Raju, K

    2015-12-01

    Full Text Available :17629 | DOI: 10.1038/srep17629 www.nature.com/scientificreports Hierarchical One-Dimensional Ammonium Nickel Phosphate Microrods for High-Performance Pseudocapacitors Kumar Raju1 & Kenneth I. Ozoemena1,2 High-performance electrochemical capacitors... OPEN w w w . n a t u r e . c o m / s c i e n t i f i c r e p o r t s / 2S C I E N T I F I C REPORTS | 5:17629 | DOI: 10.1038/srep17629 Hierarchical 1-D and 2-D materials maximize the supercapacitive properties due to their unique ability to permit ion...

  18. Growth and Chlorophyll Content of Canola Plants Supplied with Urea and Ammonium Nitrate in Response to Various Nickel Levels

    Directory of Open Access Journals (Sweden)

    Ahmad BYBORDI

    2009-12-01

    Full Text Available Both the beneficial and the adverse effects of various nickel level supplements on growth and chlorophyll content of canola plants were evaluated while either urea or ammonium nitrate was supplied as the sole N source in the nutrient solutions. This study was arranged in completely randomized with three replications. Treatments included nutrient solution cultures containing urea and ammonium nitrate at the rate of 84 mg N L-1 separately as nitrogen sources with four nickel levels as NiSO4.6H2O at the rates of 0, 0.01, 0.05 and 0.1 mg Ni L-1. Plants were allowed to grow for 6 weeks then leaves chlorophyll content and shoots and roots fresh and dry weight were determined. Both plant growth and leaves chlorophyll content of the urea-fed plants increased significantly with the increase in nickel content up to 0.1 mg Ni L-1. However, root fresh and dry weight increased up to 0.01 mg Ni L-1 and started to decrease with further increase in solutions nickel content. Nickel did not affect these parameters with plants supplied with ammonium nitrate significantly. In these plants, the optimum nickel level for shoot growth and leaves chlorophyll content was 0.05 mg L-1 and for root fresh and dry weight was 0.01 mg Ni L-1. Further increase in Ni concentration reduced growth. As a whole, plants received urea plus nickel performed better than those received ammonium nitrate plus nickel.

  19. Nitrification and N2O production processes in soil incubations after ammonium fertilizer application at high concentrations

    Science.gov (United States)

    Deppe, Marianna; Well, Reinhard; Giesemann, Anette; Flessa, Heinz

    2016-04-01

    High concentrations of ammonium as they occur, e.g., after point-injection of ammonium fertilizer solution according to the CULTAN fertilization technique may retard nitrification. Potential advantages in comparison to conventional fertilization include a higher N efficiency of crops, reduced nitrate leaching, and lower N2O and N2 emissions. Dynamics of nitrification due to plant uptake and dilution processes, leading to decreasing ammonium concentrations in fertilizer depots, has only poorly been studied before. Furthermore, there is little information about the relative contribution of different N2O production processes under these conditions. To elucidate the process dynamics a laboratory incubation study was conducted. After fertilization with ammonium sulfate at 5 levels (from 0 to 5000 mg NH4+-N kg-1; 20mg NO3--N kg-1 each), sandy loam soil was incubated in dynamic soil microcosms for 21 days. N2O, CH4 and CO2 fluxes as well as isotope signatures of N2O and, at three dates, NO3- and NH4+ were measured. To identify N2O production processes, acetylene inhibition (0.01 vol.%), 15N tracer approaches, and isotopomer data (15N site preference and δ18O) were used. N2O emissions were highest at 450mg NH4+-N kg-1 and declined with further increasing concentrations. At 5000 mg NH4+-N kg-1 nitrification was completely inhibited. However, approximately 90% of N2O production was inhibited by acetylene application, and there was no change in the relative contribution of nitrification and denitrification to N2O production with N level. Applying the non-equilibrium technique to our 15N tracer data revealed heterogeneous distribution of denitrification in soil, with at least two distinct NO3- pools, and spatial separation of NO3- formation and consumption. In comparison with the acetylene inhibition and 15N tracer approaches the results of the isotopomer approach were reasonable and indicated substantial contribution of nitrifier-denitrification (10-40%) to total N2O

  20. Ammonium nitrate explosion hazards

    Directory of Open Access Journals (Sweden)

    Negovanović Milanka

    2015-01-01

    Full Text Available Ammonium nitrate (AN primarily is used as a fertilizer but it is also very important compound in the production of industrial explosives. The application of ammonium nitrate in the production of industrial explosives was related with the early era of Nobel dynamite and widely increased with the appearance of blasting agents such as ANFO and Slurry, in the middle of the last Century. Throughout the world millions of tons of ammonium nitrate are produced annually and handled without incident. Although ammonium nitrate generally is used safely, accidental explosions involving AN have high impact resulting in loss of lives and destruction of property. The paper presents the basic properties of ammonium nitrate as well as hazards in handling of ammonium nitrate in order to prevent accidents. Several accidents with explosions of ammonium nitrate resulted in catastrophic consequences are listed in the paper as examples of non-compliance with prescribed procedures.

  1. The multiple plant response to high ammonium conditions: the Lotus japonicus AMT1; 3 protein acts as a putative transceptor.

    Science.gov (United States)

    Rogato, Alessandra; D'Apuzzo, Enrica; Chiurazzi, Maurizio

    2010-12-01

    Plant evolved a complex profile of responses to cope with changes of nutrient availability in the soil. These are based on a stringent control of expression and/or activity of proteins involved in nutrients transport and assimilation. Furthermore, a sensing and signaling system for scanning the concentration of substrates in the rooted area and for transmitting this information to the plant machinery controlling root development can be extremely useful for an efficient plant response. Ammonium represents for plants either a preferential nitrogen source or the trigger for toxicity symptoms depending by its concentration. We propose a role for the high affinity Lotus japonicus ammonium transporter LjAMT1;3 as an intracellular ammonium sensor to achieve a convenient modulation of the root development in conditions of potentially toxic external ammonium concentration.

  2. A novel heterotrophic nitrifying and aerobic denitrifying bacterium, Zobellella taiwanensis DN-7, can remove high-strength ammonium.

    Science.gov (United States)

    Lei, Yu; Wang, Yangqing; Liu, Hongjie; Xi, Chuanwu; Song, Liyan

    2016-05-01

    A novel heterotrophic bacterium capable of heterotrophic nitrification and aerobic denitrification was isolated from ammonium contaminated landfill leachate and physiochemical and phylogenetically identified as Zobellella taiwanensis DN-7. DN-7 converted nitrate, nitrate, and ammonium to N2 as the primary end product. Single factor experiments suggested that the optimal conditions for ammonium removal were trisodium citrate as carbon source, C/N ratio 8, pH 8.0-10.0, salinity less than 3 %, temperature 30 °C, and rotation speed more than 150 rpm. Specifically, DN-7 could remove 1000.0 and 2000.0 mg/L NH4 (+)-N completely within 96 and 216 h, with maximum removal rates of 19.6 and 17.3 mg L(-1) h(-1), respectively. These results demonstrated that DN-7 is a promising candidate for application of high-strength ammonium wastewater treatments.

  3. High potassium level

    Science.gov (United States)

    Hyperkalemia; Potassium - high; High blood potassium ... There are often no symptoms with a high level of potassium. When symptoms do occur, they may include: Nausea Slow, weak, or irregular pulse Sudden collapse, when the heartbeat gets too ...

  4. Tetranitroacetimidic acid: a high oxygen oxidizer and potential replacement for ammonium perchlorate.

    Science.gov (United States)

    Vo, Thao T; Parrish, Damon A; Shreeve, Jean'ne M

    2014-08-27

    Considerable work has been focused on developing replacements for ammonium perchlorate (AP), a primary choice for solid rocket and missile propellants, due to environmental concerns resulting from the release of perchlorate into groundwater systems [corrected]. Additionally, the generation of hydrochloric acid contributes to high concentrations of acid rain and to ozone layer depletion. En route to synthesizing salts that contain cationic FOX-7, a novel, high oxygen-containing oxidizer, tetranitroacetimidic acid (TNAA), has been synthesized and fully characterized. The properties of TNAA were found to be exceptional, with a calculated specific impulse exceeding that of AP, leading to its high potential as a replacement for AP. TNAA can be synthesized easily in a one-step process by the nitration of FOX-7 in high yield (>93%). The synthesis, properties, and chemical reactivity of TNAA have been examined.

  5. High blood cholesterol levels

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/000403.htm High blood cholesterol levels To use the sharing features ... stroke, and other problems. The medical term for high blood cholesterol is lipid disorder, hyperlipidemia, or hypercholesterolemia. ...

  6. High-level verification

    CERN Document Server

    Lerner, Sorin; Kundu, Sudipta

    2011-01-01

    Given the growing size and heterogeneity of Systems on Chip (SOC), the design process from initial specification to chip fabrication has become increasingly complex. This growing complexity provides incentive for designers to use high-level languages such as C, SystemC, and SystemVerilog for system-level design. While a major goal of these high-level languages is to enable verification at a higher level of abstraction, allowing early exploration of system-level designs, the focus so far for validation purposes has been on traditional testing techniques such as random testing and scenario-based

  7. Equilibrium studies of sodium-ammonium potassium-ammonium, and calcium-ammonium exchanges on clinoptilolite zeolite

    Energy Technology Data Exchange (ETDEWEB)

    Jama, M.A.; Yuecel, H. (Middle East Technical Univ., Ankara (Turkey))

    1989-12-01

    Forward and reverse ion-exchange isotherms for the binary sodium-ammonium, potassium-ammonium, and calcium-ammonium systems on clinoptilolite have been measured in aqueous solutions at a total concentration of 0.1 equiv/dm{sup 3} and at 298 K. Prior to exchange experiments it was attempted to prepare homoionic forms of the zeolite by exhaustive treatments with appropriate salt solutions of cations. With no binary exchanges, full replacement of the cation by the ammonium ion is observed, which conflicts with some earlier work on clinoptilolite. Despite the observed partial exchange levels, clinoptilolite shows a very high preference for ammonium ion over sodium and calcium but not over potassium. Thermodynamic values for the exchanges were calculated and compared with data in the literature. Both the selectivity and thermodynamic affinity sequence, in agreement with previous work reported in the literature, are K{sup +} > NH{sub 4}{sup +} > Na{sup +} > Ca{sup 2+}.

  8. Low-temperature rapid syntheses of high-quality ZnO nanostructure arrays induced by ammonium salt

    Science.gov (United States)

    Zhao, Ying; Tang, Yang; Han, Zhihua

    2017-01-01

    We have developed a simple ammonium ion-assisted hydrothermal method for the fast preparation of high quality Zinc Oxide (ZnO) nanorod arrays. Ammonium salts were introduced into typically hydrothermal growth solutions formed from Zinc acetate (ZnAc2) and hexamethylenetetramine (HMTA). Scanning electron microscope (SEM), X-ray diffractometer (XRD), High resolution transmission electron microscopic (HRTEM) and photoluminescence (PL) measurements revealed that the growth rate of ZnO nanorods was promoted by adding ammonium salts and the as-grown ZnO nanostructure arrays showed remarkably low defect density. Upon addition of ammonium salt to the hydrothermal reaction solution, complex Zn(NH3)42+ was formed by Zn2+ capturing NH3 molecules dissociated from HMTA. The improvement of growth rate and optical property of the ZnO nanostructure arrays was attributed to positively charged Zn(NH3)42+ attracting oxygen rich OH- in the growth sites of ZnO for hydrolysis reaction and simultaneously inhibiting the defect. Our results demonstrated that ammonium salt can act as a new paradigm to control morphology and quality of the ZnO microstructures.

  9. Analysis of ammonia-oxidizing bacteria dominating in lab-scale bioreactors with high ammonium bicarbonate loading

    NARCIS (Netherlands)

    Vejmelkova, D.; Sorokin, D.Y.; Abbas, B.; Kovaleva, O.L.; Kleerebezem, R.; Kampschreur, M.J.; Muyzer, G.; Van Loosdrecht, M.C.M.

    2011-01-01

    The ammonia-oxidizing bacterial community (AOB) was investigated in two types of laboratory-scale bioreactors performing partial oxidation of ammonia to nitrite or nitrate at high (80 mM) to extremely high (428 mM) concentrations of ammonium bicarbonate. At all conditions, the dominant AOB was affil

  10. Analysis of ammonia-oxidizing bacteria dominating in lab-scale bioreactors with high ammonium bicarbonate loading

    NARCIS (Netherlands)

    D. Vejmelkova; D.Y. Sorokin; B. Abbas; O.L. Kovaleva; R. Kleerebezem; M.J. Kampschreur; G. Muyzer; M.C.M. van Loosdrecht

    2012-01-01

    The ammonia-oxidizing bacterial community (AOB) was investigated in two types of laboratory-scale bioreactors performing partial oxidation of ammonia to nitrite or nitrate at high (80 mM) to extremely high (428 mM) concentrations of ammonium bicarbonate. At all conditions, the dominant AOB was affil

  11. Oriented free-standing ammonium vanadium oxide nanobelt membranes: highly selective absorbent materials.

    Science.gov (United States)

    Zou, Rujia; Zhang, Zhenyu; Yu, Li; Tian, Qiwei; Wu, Jianghong; Sun, Yangang; Chen, Zhigang; Hu, Junqing

    2010-12-27

    Highly selective, absorbent, free-standing, paper-like membranes made of ammonium vanadium oxide (NH(4)V(4)O(14)) nanobelts have been engineered by taking advantage of the nanoscaled self-assembly of architectures that display a mesh structure with an average periodic pore size of about 5 to 10 nm. The NH(4)V(4)O(14) nanobelts are synthesized by using a simple hydrothermal process, and exhibit the same orientation and assemble into bundles, each about 40 to 80 nm in width, 3 to 5 nm in thickness, and up to several millimeters in length. Importantly, the as-obtained NH(4)V(4)O(14) nanobelt membranes can highly selectively absorb a variety of organic solvents, covering both polar and non-polar solvents, for example, the absorbent capacity of glycol is 28 times as high as the initial weight of the membrane, and it can even separate organic solvents with similar polarities and absorb solid contaminants in organic solvents. These highly selective, absorbent membrane materials can be an ideal candidate for the separation and removal of pollution in industrial and environmental applications.

  12. Poly(vinyl alcohol) composite films with high percent elongation prepared from amylose-fatty ammonium salt inclusion complexes

    Science.gov (United States)

    Amylose inclusion complexes prepared from cationic fatty ammonium salts and jet-cooked high amylose starch were combined with poly(vinyl alcohol) (PVOH) to form glycerol-plasticized films. Their tensile properties were compared with similar films prepared previously with analogous anionic fatty acid...

  13. Nitrogen stable isotopes of ammonium and nitrate in high mountain lakes of the Pyrenees

    Directory of Open Access Journals (Sweden)

    M. Bartrons

    2009-12-01

    Full Text Available Nitrogen stable isotopes (δ15N are increasingly used to trace food web relationships and the flow of matter in lakes. However, there is high variability in δ15N among primary producers and other primary energy resources that can eventually propagate throughout the lake food web. To increase our understanding of the origin of this variability, we measured ammonium and nitrate δ15N in atmospheric deposition (AD, epilimnetic water (EW, deep chlorophyll maximum water (DCMW, and sediment porewater (SPW in eight mountain lakes. A general δ15N (−3.4‰ for AD was estimated as the signature for AD ammonium and nitrate did not differ. All lakes showed similar high δ15N-NH4+ values for SPW (ca. 2.2‰. In contrast, the variability among lakes in water column values was high, although differences between EW and DCMW within a lake were low. δ15N-NO3- correlated with the altitude of the lakes, and its variability was interpreted as the influence of catchment nitrification, which is higher in talus landscapes. δ15N-NH4+ distribution had two modes, positive values (ca. 3‰ were associated to DCMW of shallow lakes, and probably reflect the SPW influence. Lower values (ca. −3‰ occur in EW and DCMW of deep lakes, and its variability was related to the degree that NO3- was up taken by primary producers and recycled within the food-web when NH4+ availability was low compared to demand. Overall, altitude, lake depth and seasonal cumulative primary production largely explain the patterns of δ15N variability observed in nitrogen dissolved compounds.

  14. Trophic mode conversion and nitrogen deprivation of microalgae for high ammonium removal from synthetic wastewater.

    Science.gov (United States)

    Wang, Jinghan; Zhou, Wenguang; Yang, Haizhen; Wang, Feng; Ruan, Roger

    2015-11-01

    In this study, a well-controlled three-stage process was proposed for high ammonium removal from synthetic wastewater using selected promising microalgal strain UMN266. Three trophic modes (photoautotrophy, heterotrophy, and mixotrophy), two N sufficiency conditions (N sufficient and N deprived), two inoculum modes (photoautotrophic and heterotrophic), and different NH4(+)-N concentrations were compared to investigate the effect of trophic mode conversion and N deprivation on high NH4(+)-N removal by UMN266. Results showed that photoautotrophic inoculum with trophic mode conversion from heterotrophy to photoautotrophy and N deprivation in Stage 2 turned was the optimum plan for NH4(+)-N removal, and average removal rates were 12.4 and 19.1mg/L/d with initial NH4(+)-N of 80 and 160mg/L in Stage 3. Mechanism investigations based on algal biomass carbon (C) and N content, cellular composition, and starch content confirmed the above optimum plan and potential of UMN266 as bioethanol feedstock.

  15. Origin of high ammonium, arsenic and boron concentrations in the proximity of a mine: Natural vs. anthropogenic processes

    Energy Technology Data Exchange (ETDEWEB)

    Scheiber, Laura, E-mail: scheiber.ls@gmail.com [Institute of Environmental Assessment and Water Research, CSIC, Jordi Girona 18. E-08034 Barcelona (Spain); Ayora, Carlos; Vázquez-Suñé, Enric [Institute of Environmental Assessment and Water Research, CSIC, Jordi Girona 18. E-08034 Barcelona (Spain); Cendón, Dioni I. [Australian Nuclear Science and Technology Organisation, Locked Bag 2001, Kirrawee DC, NSW 2232 (Australia); School of Biological, Earth and Environmental Sciences (BEES), University of New South Wales (UNSW), NSW 2052 (Australia); Soler, Albert [Departament de Cristallografia, Mineralogia i Dipòsits Minerals, Facultat de Geologia, Universitat de Barcelona, C/Martí Franquès, sn., Barcelona (Spain); Baquero, Juan Carlos [Cobre Las Cruces S.A., Carretera SE-3410 km 4, 41860 Gerena, Sevilla (Spain)

    2016-01-15

    High ammonium (NH{sub 4}), arsenic (As) and boron (B) concentrations are found in aquifers worldwide and are often related to human activities. However, natural processes can also lead to groundwater quality problems. High NH{sub 4}, As and B concentrations have been identified in the confined, deep portion of the Niebla-Posadas aquifer, which is near the Cobre Las Cruces (CLC) mining complex. The mine has implemented a Drainage and Reinjection System comprising two rings of wells around the open pit mine, were the internal ring drains and the external ring is used for water reinjection into the aquifer. Differentiating geogenic and anthropogenic sources and processes is therefore crucial to ensuring good management of groundwater in this sensitive area where groundwater is extensively used for agriculture, industry, mining and human supply. No NH{sub 4}, As and B are found in the recharge area, but their concentrations increase with depth, salinity and residence time of water in the aquifer. The increased salinity down-flow is interpreted as the result of natural mixing between infiltrated meteoric water and the remains of connate waters (up to 8%) trapped within the pores. Ammonium and boron are interpreted as the result of marine solid organic matter degradation by the sulfate dissolved in the recharge water. The light δ{sup 15}N{sub NH4} values confirm that its origin is linked to marine organic matter. High arsenic concentrations in groundwater are interpreted as being derived from reductive dissolution of As-bearing goethite by dissolved organic matter. The lack of correlation between dissolved Fe and As is explained by the massive precipitation of siderite, which is abundantly found in the mineralization. Therefore, the presence of high arsenic, ammonium and boron concentrations is attributed to natural processes. Ammonium, arsenic, boron and salinity define three zones of groundwater quality: the first zone is close to the recharge area and contains water

  16. Origin of high ammonium, arsenic and boron concentrations in the proximity of a mine: Natural vs. anthropogenic processes.

    Science.gov (United States)

    Scheiber, Laura; Ayora, Carlos; Vázquez-Suñé, Enric; Cendón, Dioni I; Soler, Albert; Baquero, Juan Carlos

    2016-01-15

    High ammonium (NH4), arsenic (As) and boron (B) concentrations are found in aquifers worldwide and are often related to human activities. However, natural processes can also lead to groundwater quality problems. High NH4, As and B concentrations have been identified in the confined, deep portion of the Niebla-Posadas aquifer, which is near the Cobre Las Cruces (CLC) mining complex. The mine has implemented a Drainage and Reinjection System comprising two rings of wells around the open pit mine, were the internal ring drains and the external ring is used for water reinjection into the aquifer. Differentiating geogenic and anthropogenic sources and processes is therefore crucial to ensuring good management of groundwater in this sensitive area where groundwater is extensively used for agriculture, industry, mining and human supply. No NH4, As and B are found in the recharge area, but their concentrations increase with depth, salinity and residence time of water in the aquifer. The increased salinity down-flow is interpreted as the result of natural mixing between infiltrated meteoric water and the remains of connate waters (up to 8%) trapped within the pores. Ammonium and boron are interpreted as the result of marine solid organic matter degradation by the sulfate dissolved in the recharge water. The light δ(15)NNH4 values confirm that its origin is linked to marine organic matter. High arsenic concentrations in groundwater are interpreted as being derived from reductive dissolution of As-bearing goethite by dissolved organic matter. The lack of correlation between dissolved Fe and As is explained by the massive precipitation of siderite, which is abundantly found in the mineralization. Therefore, the presence of high arsenic, ammonium and boron concentrations is attributed to natural processes. Ammonium, arsenic, boron and salinity define three zones of groundwater quality: the first zone is close to the recharge area and contains water of sufficient quality for

  17. ALICE High Level Trigger

    CERN Multimedia

    Alt, T

    2013-01-01

    The ALICE High Level Trigger (HLT) is a computing farm designed and build for the real-time, online processing of the raw data produced by the ALICE detectors. Events are fully reconstructed from the raw data, analyzed and compressed. The analysis summary together with the compressed data and a trigger decision is sent to the DAQ. In addition the reconstruction of the events allows for on-line monitoring of physical observables and this information is provided to the Data Quality Monitor (DQM). The HLT can process event rates of up to 2 kHz for proton-proton and 200 Hz for Pb-Pb central collisions.

  18. Effects of ammonium ion, acetate and aerobic conditions on hydrogen production and expression levels of nitrogenase genes in Rhodobacter sphaeroides O.U.001

    Energy Technology Data Exchange (ETDEWEB)

    Akkoese, Sevilay; Guenduez, Ufuk; Yuecel, Meral [Middle East Technical University, Department of Biological Sciences, 06531 Ankara (Turkey); Eroglu, Inci [Middle East Technical University, Department of Chemical Engineering, 06531 Ankara (Turkey)

    2009-11-15

    In the present study, expression levels of nitrogenase encoding nifH and control genes nifA and prrA were examined at different physiological conditions in Rhodobacter sphaeroides O.U.001. In addition to variations in expression levels, changes in hydrogen production and growth were also investigated in response to different concentrations of ammonium source, acetate and aerobic conditions. In the present study, increasing concentration of ammonium chloride was found to be caused decrease in hydrogen production. Glutamate containing medium had the capacity for higher hydrogen production. Hydrogen production was observed even in aerobic conditions. The expression levels of nifH and nifA genes decreased with the increasing concentrations of ammonium chloride. Although the expression of nifA was present in the highest concentrations of NH{sub 4}Cl under anaerobic conditions, no expression was observed under aerobic conditions of the same culture conditions. This was likely due to transcriptional level inhibition of nitrogenase in the presence of ammonium ion. Negative correlation was observed between the expression levels of prrA gene and its target, nifA gene. (author)

  19. High durability and low toxicity antimicrobial coatings fabricated by quaternary ammonium silane copolymers.

    Science.gov (United States)

    Li, Hairui; Bao, Hongqian; Bok, Ke Xin; Lee, Chi-Ying; Li, Bo; Zin, Melvin T; Kang, Lifeng

    2016-02-01

    Adhesion and subsequent growth of microorganisms on material surfaces are a major concern in many biomedical applications. Currently, various polymers are immobilized on material surfaces to prevent microbial colonization. However, there are several challenges with regard to the coating materials, including their inability to kill microorganisms, complexity of surface grafting, limited durability and toxicity towards humans. To address these challenges, we synthesize a novel quaternary ammonium silane (QAS) antimicrobial copolymer to confer the antimicrobial effect via a simple thermal-curing coating process. The QAS copolymers were less toxic to 3 human cell lines than a commercial antimicrobial QAS monomeric agent, namely, dimethyloctadecyl[3-(trimethoxysilyl) propyl]ammonium chloride (DTPAC). Moreover, the QAS coatings demonstrated superior antimicrobial efficacy and durability than those of the DTPAC coatings. In conclusion, the novel QAS copolymers are useful to prevent substrates from microbial infections, yet with low toxicity to humans and long durability. In addition, the synthetic process is potentially scalable for industrial applications.

  20. Seasonal patterns of ammonium regeneration from size-fractionated microheterotrophs

    Science.gov (United States)

    Maguer, Jean-François; L'Helguen, Stéphane; Madec, Christian; Le Corre, Pierre

    1999-11-01

    Ammonium regeneration by size-fractionated plankton was measured for 1 year at a coastal station in the shallow well-mixed waters of the western English Channel. Rates of ammonium regeneration in the Journal of Plankton Research, 18, 355-370). Total ammonium regenerated in a year by the microheterotrophs was 15 g N m -2, equivalent to about 60% of the total nitrogen uptake. Microplankton (200-15 μm) accounted for about 50% of the regeneration measured between early spring and late summer. Percent contribution of nanoplankton to total ammonium regeneration varied considerably between the seasons, from very high (83-88%) levels in winter to very low (2-13%) levels in summer. Contribution by picoplankton (nano- and picoplankton fractions, appears to be different from that in deep well-mixed waters. Here, the relative contribution of ciliates and bacteria to ammonium regeneration shows little variation with an increase in macrozooplankton biomass.

  1. Ammonium Additives to Dissolve Lithium Sulfide through Hydrogen Binding for High-Energy Lithium–Sulfur Batteries

    Energy Technology Data Exchange (ETDEWEB)

    Pan, Huilin; Han, Kee Sung; Vijayakumar, M.; Xiao, Jie; Cao, Ruiguo; Chen, Junzheng; Zhang, Jiguang; Mueller, Karl T.; Shao, Yuyan; Liu, Jun

    2016-07-01

    In rechargeable Li-S batteries, the uncontrollable passivation of electrodes by highly insulating Li2S limits sulfur utilization, increases polarization and decreases cycling stability. Dissolving Li2S in organic electrolyte is a facile solution to maintain the active reaction interface between electrolyte and sulfur cathode, and thus address the above issues. Herein, ammonium salts are demonstrated as effective additives to promote the dissolution of Li2S to 1.25 M in DMSO solvent at room temperature. NMR measurements show that the strong hydrogen binding effect of N-H groups plays a critical role in dissolving Li2S by forming complex ligands with S2- anions coupled with the solvent’s solvating surrounding. Ammonium additives in electrolyte can also significantly improve the oxidation kinetics of Li2S, therefore enables the direct use of Li2S as cathode material in Li-S battery system in the future. This provides a new approach to manage the solubility of lithium sulfides through cation coordination with sulfide anion.

  2. Start-up of a biofilm airlift system to obtain partial nitrification of a high-strength ammonium wastewater

    Energy Technology Data Exchange (ETDEWEB)

    Bartoli, A.; Perez, J.; Lafuente, J.; Carrera, J.

    2009-07-01

    In order to fulfil the new legal requirements with regards to the sewage sludge produced in the WWTPs an on-going EU research project is devoted to the reduction. Modification and valorisation of sludge (REMOVALS, n 018525, www.etseq.urv.es/removals/). Among many other initiatives inside this project, a possible valorisation of sluge is the production of activated carbon (AC) which could be use, among other applications, as carrier for biofilm development. One of the possible applications of biofilm reactors in the current process diagram of a WWTP is the specific treatment of a high-strength ammonium wastewater produced in the anaerobic digestion of the sludge, the so-called reject water. (Author)

  3. Sulfate-reducing anaerobic ammonium oxidation as a potential treatment method for high nitrogen-content wastewater.

    Science.gov (United States)

    Rikmann, Ergo; Zekker, Ivar; Tomingas, Martin; Tenno, Taavo; Menert, Anne; Loorits, Liis; Tenno, Toomas

    2012-07-01

    After sulfate-reducing ammonium oxidation (SRAO) was first assumed in 2001, several works have been published describing this process in laboratory-scale bioreactors or occurring in the nature. In this paper, the SRAO process was performed using reject water as a substrate for microorganisms and a source of NH(4) (+), with SO(4) (2-) being added as an electron acceptor. At a moderate temperature of 20°C in a moving bed biofilm reactor (MBBR) sulfate reduction along with ammonium oxidation were established. In an upflow anaerobic sludge blanket reactor (UASBR) the SRAO process took place at 36°C. Average volumetric TN removal rates of 0.03 kg-N/m³/day in the MBBR and 0.04 kg-N/m³/day in the UASBR were achieved, with long-term moderate average removal efficiencies, respectively. Uncultured bacteria clone P4 and uncultured planctomycete clone Amx-PAn30 were detected from the biofilm of the MBBR, from sludge of the UASBR uncultured Verrucomicrobiales bacterium clone De2102 and Uncultured bacterium clone ATB-KS-1929 were found also. The stoichiometrical ratio of NH(4) (+) removal was significantly higher than could be expected from the extent of SO(4) (2-) reduction. This phenomenon can primarily be attributed to complex interactions between nitrogen and sulfur compounds and organic matter present in the wastewater. The high NH(4) (+) removal ratio can be attributed to sulfur-utilizing denitrification/denitritation providing the evidence that SRAO is occurring independently and is not a result of sulfate reduction and anammox. HCO(3) (-) concentrations exceeding 1,000 mg/l were found to have an inhibiting effect on the SRAO process. Small amounts of hydrazine were naturally present in the reaction medium, indicating occurrence of the anammox process. Injections of anammox intermediates, hydrazine and hydroxylamine, had a positive effect on SRAO process performance, particularly in the case of the UASBR.

  4. High level binocular rivalry effects

    Directory of Open Access Journals (Sweden)

    Michal eWolf

    2011-12-01

    Full Text Available Binocular rivalry (BR occurs when the brain cannot fuse percepts from the two eyes because they are different. We review results relating to an ongoing controversy regarding the cortical site of the BR mechanism. Some BR qualities suggest it is low-level: 1 BR, as its name implies, is usually between eyes and only low levels have access to utrocular information. 2 All input to one eye is suppressed: blurring doesn’t stimulate accommodation; pupilary constrictions are reduced; probe detection is reduced. 3 Rivalry is affected by low level attributes, contrast, spatial frequency, brightness, motion. 4 There is limited priming due to suppressed words or pictures. On the other hand, recent studies favor a high level mechanism: 1 Rivalry occurs between patterns, not eyes, as in patchwork rivalry or a swapping paradigm. 2 Attention affects alternations. 3 Context affects dominance. There is conflicting evidence from physiological studies (single cell and fMRI regarding cortical level(s of conscious perception. We discuss the possibility of multiple BR sites and theoretical considerations that rule out this solution.We present new data regarding the locus of the BR switch by manipulating stimulus semantic content or high-level characteristics. Since these variations are represented at higher cortical levels, their affecting rivalry supports high-level BR intervention. In Experiment I, we measure rivalry when one eye views words and the other nonwords and find significantly longer dominance durations for nonwords. In Experiment II, we find longer dominance times for line drawings of simple, structurally impossible figures than for similar, possible objects. In Experiment III, we test the influence of idiomatic context on rivalry between words. Results show that generally words within their idiomatic context have longer mean dominance durations. We conclude that Binocular Rivalry has high-level cortical influences, and may be controlled by a high-level

  5. Isotopically enriched ammonium shows high nitrogen transformation in the pile top zone of dairy manure compost

    Directory of Open Access Journals (Sweden)

    K. Maeda

    2016-03-01

    significantly high 15N (δ15N: 12.7–29.8 ‰ values, indicating that extremely high nitrogen conversion, nitrification–denitrification activity of the microbes and NH3 volatilization occurred in this zone.

  6. The effect of the ammonium ion on activated-sludge settling properties

    DEFF Research Database (Denmark)

    Novak, John Thomas

    2001-01-01

    High levels of sodium in wastewater have been found to be detrimental to activated-sludge. settling and dewatering. Another potentially troublesome monovalent cation in activated-sludge systems is the ammonium ion. This study was conducted to determine if the ammonium ion could alter activated-sl...

  7. High-energy coordination polymers (CPs) exhibiting good catalytic effect on the thermal decomposition of ammonium dinitramide

    Science.gov (United States)

    Li, Xin; Han, Jing; Zhang, Sheng; Zhai, Lianjie; Wang, Bozhou; Yang, Qi; Wei, Qing; Xie, Gang; Chen, Sanping; Gao, Shengli

    2017-09-01

    High-energy coordination polymers (CPs) not only exhibit good energetic performances but also have a good catalytic effect on the thermal decomposition of energetic materials. In this contribution, two high-energy CPs Cu2(DNBT)2(CH3OH)(H2O)3·3H2O (1) and [Cu3(DDT)2(H2O)2]n (2) (H2DNBT = 3,3‧-dinitro-5,5‧-bis(1H-1,2,4-triazole and H3DDT = 4,5-bis(1H-tetrazol-5-yl)-2H-1,2,3-triazole) were synthesized and structurally characterized. Furthermore, 1 was thermos-dehydrated to produce Cu2(DNBT)2(CH3OH)(H2O)3 (1a). The thermal decomposition kinetics of 1, 1a and 2 were studied by Kissinger's method and Ozawa's method. Thermal analyses and sensitivity tests show that all compounds exhibit high thermal stability and low sensitivity for external stimuli. Meanwhile, all compounds have large positive enthalpy of formation, which are calculated as being (1067.67 ± 2.62) kJ mol-1 (1), (1464.12 ± 3.12) kJ mol-1 (1a) and (3877.82 ± 2.75) kJ mol-1 (2), respectively. The catalytic effects of 1a and 2 on the thermal decomposition of ammonium dinitramide (ADN) were also investigated.

  8. Novel Ammonium Metal Borohydrides

    DEFF Research Database (Denmark)

    Grinderslev, Jakob; Jepsen, Lars Haahr; Cerny, Radovan

    , it cannot store hydrogen reversibly. Recently, the first ammonium metal borohydride, NH4Ca(BH4)3 was published, which may be considered as substitution of K+ by NH4+ in KCa(BH4)3, due to the similar sizes of NH4+ and K+[1]. This compound successfully stabilizes NH4BH4. In the present work, a series of novel......, and the crystal structures and thermal decompositions are investigated. Mixtures of NH4BH4 - NaBH4 do not react, while solid solutions, K1-x(NH4)xBH4, are formed for NH4BH4 - KBH4. For the other composites, novel ammonium metal borohydrides are formed. Several of these structures have been solved from high...

  9. Plants Growth Rate in Evapotranspiration continuous system reactors as the 2nd Treatment at Anaerobic-evapotranspiration system with High Strength Ammonium in Leachate Influent

    Directory of Open Access Journals (Sweden)

    Badrus Zaman

    2014-05-01

    Full Text Available Ammonium is one of parameter which responsible to leachate toxicity. Preliminary research was shown that the Fimbristylis globulosa (water plant, Alocasia macrorrhiza (terrestrial plant and Eleusine indica (terrestrial grass were potential plants for used as object in evaporation reactor system with high strength ammonium  concentration in leachate treatment. This research was integrated of anaerobic system with evapotranspiration system with continuous influent using ammonium concentration in leachate was 2000 mg/l NH4-N. Plants growth rate was analyzed for 25 days operated. The result shown that average of thallus growth rate of Fimbristylis globulosa was 17,5 cm d-1. The average of leaf and thallus growth rate of Alocasia macrorrhiza was 18,1 cm d-1 and 3,2 cm d-1 respectively. The average of blade and thallus of Eleusine indica were same that was 4,7 cm d-1.This research conclude that integration system of anaerobic and evpotranspiration was be potential used for high strength ammonium in leachate treatment.

  10. Isotopically enriched ammonium shows high nitrogen transformation in the pile top zone of dairy manure compost

    Science.gov (United States)

    Maeda, Koki; Toyoda, Sakae; Yano, Midori; Hattori, Shohei; Fukasawa, Makoto; Nakajima, Keiichi; Yoshida, Naohiro

    2016-03-01

    Nitrogen isotope ratios (δ15N) of NH4+ in dairy manure compost piles with and without bulking agent (10 % w/w) were compared to understand the effects of the use of bulking agent on nitrogen conversion during manure composting. The δ15N-NH4+ values in each of three pile zones (top, side and core) were also compared. At the end of the process, piles with bulking agent showed significantly higher δ15N values (17.7 ± 1.3 ‰) than piles without bulking agent (11.8 ± 0.9 ‰), reflecting the significantly higher nitrogen conversion and NH3 loss in the former. The samples from the top zone, especially in the piles with bulking agent, showed very high NH4+ concentrations with significantly high 15N (δ15N: 12.7-29.8 ‰) values, indicating that extremely high nitrogen conversion, nitrification-denitrification activity of the microbes and NH3 volatilization occurred in this zone.

  11. EFFECT OF RADIATION ON HIGH-CHARGE-DENSITY POLYDIALLY-DIMETHYL AMMONIUM CHLORIDE IN DILUTE AQUEOUS SOLUTION

    Institute of Scientific and Technical Information of China (English)

    Ya-long Zhang; Min Yi; Jing Ren; Hong-fei Ha

    2003-01-01

    The effect of radiation on high-charge-density cationic polymer, polydiallyl-dimethyl ammonium chloride (polyDADMAC), in dilute aqueous solution was investigated. The irradiated samples were characterized in terms of reduced viscosity and electric conductivity. The crosslinking reaction of polyDADMAC chains occurs preferentially in the irradiated samples at a concentration of polyDADMAC higher than 1.3 g/100 mL that was induced indirectly by the OH radicals, one of the radiolysis products of water. In more dilute samples (less than 0.8 g/100 mL) the chain scission of macro radicals appears to be the main reaction. N2O atmosphere enhances the erosslinking due to the extra OH radicals produced by reaction between N2O and eaq, another radiolysis products of water. Methanol and some mineral salts such as KC1, KBr inhibit the crosslinking to a certain extent. The mechanism of sensitization and inhibition is discussed in detail.

  12. Ammonium hydroxide modulated synthesis of high-quality fluorescent carbon dots for white LEDs with excellent color rendering properties

    Science.gov (United States)

    Wang, Shengda; Zhu, Zhifeng; Chang, Yajing; Wang, Hui; Yuan, Nan; Li, Guopeng; Yu, Dabin; Jiang, Yang

    2016-07-01

    A novel type of aqueous fluorescent carbon dot (CD) was synthesized using citric acid as the only carbon source via an ammonium hydroxide modulated method, providing a blue color gamut. The amino group is considered to be the key factor in the high fluorescence of CDs and a model is established to investigate the mechanism of fluorescence. In addition, white light-emitting diodes (WLEDs) are fabricated by utilizing the prepared CDs and rare earth luminescent materials (SrSi2O2N2:Eu and Sr2Si5N8:Eu) as color conversion layers and UV-LED chips as the excitation light source. The WLEDs produce bright white light with attractive color rendering properties including a color rendering index of up to 95.1, a CIE coordinate of (0.33, 0.37), and a T c of 5447 K under a 100 mA driven current, indicating that the CDs are promising in the field of optoelectronic devices.

  13. Using ammonium-tolerant yeast isolates: Candida halophila and Rhodotorula glutinis to treat high strength fermentative wastewater.

    Science.gov (United States)

    Yang, Q; Yang, M; Hei, L; Zheng, S

    2003-03-01

    Two ammonium-tolerant yeast strains were isolated from sludge samples contaminated with monosodium glutamate manufacturing wastewater and were identified as Candida haplophila and Rhodotorula glutinis. The tolerance of the two yeast isolates to ammonia and their chemical oxygen demand (COD) removal perfomances were evaluated under batch and bench-scale conditions. The mixture of the two isolates was found to grow well in an artificial medium containing 25% (NH4)2SO4 and could effectively remove COD from monosodium glutamate wastewater even when the concentrations of NH4+-N and free NH3-N reached as high as 18,977 and 879 mg l(-1) respectively. A fixed-bed yeast reactor, which was initially inoculated with the yeast mixture, permitted a constant COD removal rate of over 80% during a period of near 2-month continuous running even when the influent COD was increased from 8,000 to 25,000 mg l(-1). The effluent was accompanied with suspended solids (SS) of over 4,500 mg l(-1), which was mainly composed of yeast cells and could be considered as a source of animal forage additive. The residual COD of effluents from the yeast reactor could be further reduced to under 500 mg l(-1) by a combination process of activated sludge treatment and coagulation technologies.

  14. Highly efficient non-biofouling coating of zwitterionic polymers: poly((3-(methacryloylamino)propyl)-dimethyl(3-sulfopropyl)ammonium hydroxide).

    Science.gov (United States)

    Cho, Woo Kyung; Kong, Bokyung; Choi, Insung S

    2007-05-08

    This work describes the formation of highly efficient non-biofouling polymeric thin films of poly((3-(methacryloylamino)propyl)-dimethyl(3-sulfopropyl)ammonium hydroxide), (poly(MPDSAH)). The poly(MPDSAH) films were generated from the self-assembled monolayers terminating in an initiator of atom transfer radical polymerization (ATRP) by the surface-initiated ATRP of MPDSAH. The poly(MPDSAH) films on a gold surface were characterized by ellipsometry, FT-IR spectroscopy, contact angle goniometery, and X-ray photoelectron spectroscopy. The copper complexes and unpolymerized monomers trapped inside the polymer brushes were completely washed out by soaking the poly(MPDSAH)-coated substrate in water at 40 degrees C for 4 days. The amount of proteins nonspecifically adsorbed onto the poly(MPDSAH) films was evaluated by surface plasmon resonance spectroscopy: the adsorption of proteins was <0.6 ng/cm(2) on the surfaces for all the model proteins. The ability of the poly(MPDSAH) films to resist the nonspecific adsorption of proteins was comparable to that of the best known systems.

  15. High-Level Radioactive Waste.

    Science.gov (United States)

    Hayden, Howard C.

    1995-01-01

    Presents a method to calculate the amount of high-level radioactive waste by taking into consideration the following factors: the fission process that yields the waste, identification of the waste, the energy required to run a 1-GWe plant for one year, and the uranium mass required to produce that energy. Briefly discusses waste disposal and…

  16. High-level Petri Nets

    DEFF Research Database (Denmark)

    of some of the most important papers on the application and theory of high-level Petri nets. In this way it makes the relevant literature more available. It is our hope that the book will be a useful source of information and that, e.g., it can be used in the organization of Petri net courses. To make...... there is only one kind of token and this means that the state of a place is described by an integer (and in many cases even by a boolean). In high-level nets each token can carry a complex information/data - which, e.g., may describe the entire state of a process or a data base. Today most practical...... by other papers. Thus, e.g., none of the original papers introducing the first versions of high-level Petri nets have been included. The introductions to the individual sections mention a number of researchers who have contributed to the development of high-level Petri nets. Detailed references...

  17. RPython high-level synthesis

    Science.gov (United States)

    Cieszewski, Radoslaw; Linczuk, Maciej

    2016-09-01

    The development of FPGA technology and the increasing complexity of applications in recent decades have forced compilers to move to higher abstraction levels. Compilers interprets an algorithmic description of a desired behavior written in High-Level Languages (HLLs) and translate it to Hardware Description Languages (HDLs). This paper presents a RPython based High-Level synthesis (HLS) compiler. The compiler get the configuration parameters and map RPython program to VHDL. Then, VHDL code can be used to program FPGA chips. In comparison of other technologies usage, FPGAs have the potential to achieve far greater performance than software as a result of omitting the fetch-decode-execute operations of General Purpose Processors (GPUs), and introduce more parallel computation. This can be exploited by utilizing many resources at the same time. Creating parallel algorithms computed with FPGAs in pure HDL is difficult and time consuming. Implementation time can be greatly reduced with High-Level Synthesis compiler. This article describes design methodologies and tools, implementation and first results of created VHDL backend for RPython compiler.

  18. The CMS High Level Trigger

    CERN Document Server

    Adam, W; Deldicque, C; Ero, J; Frühwirth, R; Jeitler, Manfred; Kastner, K; Köstner, S; Neumeister, N; Porth, M; Padrta P; Rohringer, H; Sakulinb, H; Strauss, J; Taurok, A; Walzel, G; Wulz, C E; Lowette, S; Van De Vyver, B; De Lentdecker, G; Vanlaer, P; Delaere, C; Lemaître, V; Ninane, A; van der Aa, O; Damgov, J; Karimäki, V; Kinnunen, R; Lampen, T; Lassila-Perini, K M; Lehti, S; Nysten, J; Tuominiemi, J; Busson, P; Todorov, T; Schwering, G; Gras, P; Daskalakis, G; Sfyrla, A; Barone, M; Geralis, T; Markou, C; Zachariadou, K; Hidas, P; Banerjee, S; Mazumdara, K; Abbrescia, M; Colaleoa, A; D'Amato, N; De Filippis, N; Giordano, D; Loddo, F; Maggi, M; Silvestris, L; Zito, G; Arcelli, S; Bonacorsi, D; Capiluppi, P; Dallavalle, G M; Fanfani, A; Grandi, C; Marcellini, S; Montanari, A; Odorici, F; Travaglini, R; Costa, S; Tricomi, A; Ciulli, a V; Magini, N; Ranieri, R; Berti, L; Biasotto, M; Gulminia, M; Maron, G; Toniolo, N; Zangrando, L; Bellato, M; Gasparini, U; Lacaprara, S; Parenti, A; Ronchese, P; Vanini, S; Zotto, S; Ventura P L; Perugia; Benedetti, D; Biasini, M; Fano, L; Servoli, L; Bagliesi, a G; Boccali, T; Dutta, S; Gennai, S; Giassi, A; Palla, F; Segneri, G; Starodumov, A; Tenchini, R; Meridiani, P; Organtini, G; Amapane, a N; Bertolino, F; Cirio, R; Kim, J Y; Lim, I T; Pac, Y; Joo, K; Kim, S B; Suwon; Choi, Y I; Yu, I T; Cho, K; Chung, J; Ham, S W; Kim, D H; Kim, G N; Kim, W; CKim, J; Oh, S K; Park, H; Ro, S R; Son, D C; Suh, J S; Aftab, Z; Hoorani, H; Osmana, A; Bunkowski, K; Cwiok, M; Dominik, Wojciech; Doroba, K; Kazana, M; Królikowski, J; Kudla, I; Pietrusinski, M; Pozniak, Krzysztof T; Zabolotny, W M; Zalipska, J; Zych, P; Goscilo, L; Górski, M; Wrochna, G; Zalewski, P; Alemany-Fernandez, R; Almeida, C; Almeida, N; Da Silva, J C; Santos, M; Teixeira, I; Teixeira, J P; Varelaa, J; Vaz-Cardoso, N; Konoplyanikov, V F; Urkinbaev, A R; Toropin, A; Gavrilov, V; Kolosov, V; Krokhotin, A; Oulianov, A; Stepanov, N; Kodolova, O L; Vardanyan, I; Ilic, J; Skoro, G P; Albajar, C; De Troconiz, J F; Calderón, A; López-Virto, M A; Marco, R; Martínez-Rivero, C; Matorras, F; Vila, I; Cucciarelli, S; Konecki, M; Ashby, S; Barney, D; Bartalini, P; Benetta, R; Brigljevic, V; Bruno, G; Cano, E; Cittolin, S; Della Negra, M; de Roeck, A; Favre, P; Frey, A; Funk, W; Futyan, D; Gigi, D; Glege, F; Gutleber, J; Hansen, M; Innocente, V; Jacobs, C; Jank, W; Kozlovszky, Miklos; Larsen, H; Lenzi, M; Magrans, I; Mannelli, M; Meijers, F; Meschi, E; Mirabito, L; Murray, S J; Oh, A; Orsini, L; Palomares-Espiga, C; Pollet, L; Rácz, A; Reynaud, S; Samyn, D; Scharff-Hansen, P; Schwick, C; Sguazzoni, G; Sinanis, N; Sphicas, P; Spiropulu, M; Strandlie, A; Taylor, B G; Van Vulpen, I; Wellisch, J P; Winkler, M; Villigen; Kotlinski, D; Zurich; Prokofiev, K; Speer, T; Dumanoglu, I; Bristol; Bailey, S; Brooke, J J; Cussans, D; Heath, G P; Machin, D; Nash, S J; Newbold, D; Didcot; Coughlan, A; Halsall, R; Haynes, W J; Tomalin, I R; Marinelli, N; Nikitenko, A; Rutherford, S; Seeza, C; Sharif, O; Antchev, G; Hazen, E; Rohlf, J; Wu, S; Breedon, R; Cox, P T; Murray, P; Tripathi, M; Cousins, R; Erhan, S; Hauser, J; Kreuzer, P; Lindgren, M; Mumford, J; Schlein, P E; Shi, Y; Tannenbaum, B; Valuev, V; Von der Mey, M; Andreevaa, I; Clare, R; Villa, S; Bhattacharya, S; Branson, J G; Fisk, I; Letts, J; Mojaver, M; Paar, H P; Trepagnier, E; Litvine, V; Shevchenko, S; Singh, S; Wilkinson, R; Aziz, S; Bowden, M; Elias, J E; Graham, G; Green, D; Litmaath, M; Los, S; O'Dell, V; Ratnikova, N; Suzuki, I; Wenzel, H; Acosta, D; Bourilkov, D; Korytov, A; Madorsky, A; Mitselmakher, G; Rodríguez, J L; Scurlock, B; Abdullin, S; Baden, D; Eno, S; Grassi, T; Kunori, S; Pavlon, S; Sumorok, K; Tether, S; Cremaldi, L M; Sanders, D; Summers, D; Osborne, I; Taylor, L; Tuura, L; Fisher,W C; Mans6, J; Stickland, D P; Tully, C; Wildish, T; Wynhoff, S; Padley, B P; Chumney, P; Dasu, S; Smith, W H; CMS Trigger Data Acquisition Group

    2006-01-01

    At the Large Hadron Collider at CERN the proton bunches cross at a rate of 40MHz. At the Compact Muon Solenoid experiment the original collision rate is reduced by a factor of O (1000) using a Level-1 hardware trigger. A subsequent factor of O(1000) data reduction is obtained by a software-implemented High Level Trigger (HLT) selection that is executed on a multi-processor farm. In this review we present in detail prototype CMS HLT physics selection algorithms, expected trigger rates and trigger performance in terms of both physics efficiency and timing.

  19. The ALICE high level trigger

    Science.gov (United States)

    Alt, T.; Grastveit, G.; Helstrup, H.; Lindenstruth, V.; Loizides, C.; Röhrich, D.; Skaali, B.; Steinbeck, T.; Stock, R.; Tilsner, H.; Ullaland, K.; Vestbø, A.; Vik, T.; Wiebalck, A.; the ALICE Collaboration

    2004-08-01

    The ALICE experiment at LHC will implement a high-level trigger system for online event selection and/or data compression. The largest computing challenge is posed by the TPC detector, which requires real-time pattern recognition. The system entails a very large processing farm that is designed for an anticipated input data stream of 25 GB s-1. In this paper, we present the architecture of the system and the current state of the tracking methods and data compression applications.

  20. Quantifying Temporal Autocorrelations for the Expression of Geobacter species mRNA Gene Transcripts at Variable Ammonium Levels during in situ U(VI) Bioremediation

    Science.gov (United States)

    Mouser, P. J.

    2010-12-01

    In order to develop decision-making tools for the prediction and optimization of subsurface bioremediation strategies, we must be able to link the molecular-scale activity of microorganisms involved in remediation processes with biogeochemical processes observed at the field-scale. This requires the ability to quantify changes in the in situ metabolic condition of dominant microbes and associate these changes to fluctuations in nutrient levels throughout the bioremediation process. It also necessitates a need to understand the spatiotemporal variability of the molecular-scale information to develop meaningful parameters and constraint ranges in complex bio-physio-chemical models. The expression of three Geobacter species genes (ammonium transporter (amtB), nitrogen fixation (nifD), and a housekeeping gene (recA)) were tracked at two monitoring locations that differed significantly in ammonium (NH4+) concentrations during a field-scale experiment where acetate was injected into the subsurface to simulate Geobacteraceae in a uranium-contaminated aquifer. Analysis of amtB and nifD mRNA transcript levels indicated that NH4+ was the primary form of fixed nitrogen during bioremediation. Overall expression levels of amtB were on average 8-fold higher at NH4+ concentrations of 300 μM or more than at lower NH4+ levels (average 60 μM). The degree of temporal correlation in Geobacter species mRNA expression levels was calculated at both locations using autocorrelation methods that describe the relationship between sample semi-variance and time lag. At the monitoring location with lower NH4+, a temporal correlation lag of 8 days was observed for both amtB and nifD transcript patterns. At the location where higher NH4+ levels were observed, no discernable temporal correlation lag above the sampling frequency (approximately every 2 days) was observed for amtB or nifD transcript fluctuations. Autocorrelation trends in recA expression levels at both locations indicated that

  1. Fermi level pinning characterisation on ammonium fluoride-treated surfaces of silicon by energy-filtered doping contrast in the scanning electron microscope

    Science.gov (United States)

    Chee, Augustus K. W.

    2016-08-01

    Two-dimensional dopant profiling using the secondary electron (SE) signal in the scanning electron microscope (SEM) is a technique gaining impulse for its ability to enable rapid and contactless low-cost diagnostics for integrated device manufacturing. The basis is doping contrast from electrical p-n junctions, which can be influenced by wet-chemical processing methods typically adopted in ULSI technology. This paper describes the results of doping contrast studies by energy-filtering in the SEM from silicon p-n junction specimens that were etched in ammonium fluoride solution. Experimental SE micro-spectroscopy and numerical simulations indicate that Fermi level pinning occurred on the surface of the treated-specimen, and that the doping contrast can be explained in terms of the ionisation energy integral for SEs, which is a function of the dopant concentration, and surface band-bending effects that prevail in the mechanism for doping contrast as patch fields from the specimen are suppressed.

  2. Fixed Ammonium Content and Maximum Capacity of Ammonium Fixation in Major Types of Tillage Soils in Hunan Province, China

    Institute of Scientific and Technical Information of China (English)

    ZHANG Yang-zhu; HUANG Shun-hong; WAN Da-juan; HUANG Yun-xiang; ZHOU Wei-jun; ZOU Ying-bin

    2007-01-01

    In order to understand the status of fixed ammonium, fixed ammonium content, maximum capacity of ammonium fixation, and their influencing factors in major types of tillage soils of Hunan Province, China, were studied with sampling on fields, and laboratory incubation and determination. The main results are summarized as follows: (1) Content of fixed ammonium in the tested soils varies greatly with soil use pattern and the nature of parent material. For the paddy soils, it ranges from 135.4 ± 57.4 to 412.8±32.4 mg kg-1, with 304.7±96.7 mg kg-1 in average; while it ranges from 59.4 to 435.7 mg kg-1, with 230.1 ± 89.2 mg kg1 in average for the upland soils. The soils developed from limnic material and slate had higher fixed ammonium content than the soils developed from granite. The percentage of fixed ammonium to total N in the upland soils is always higher than that in the paddy soils. It ranges from 6.1 ± 3.6% to 16.6 ±4.6%, with 14.0% ± 5.1% in average for the paddy soils and it amounted to 5.8 ±2.0% to 40.1 ± 17.8%, with 23.5 ± 14.2% in average for upland soils. (2) The maximum capacity of ammonium fixation has the same trend with the fixed ammonium content in the tested soils. For all the tested soils, the percentage of recently fixed ammonium to maximum capacity of ammonium fixation is always bellow 20% and it may be due to the fact that the soils have high fertility and high saturation of ammonium-fixing site. (3) The clay content and clay composition in the tested soils are the two important factors influe ncing their fixed ammonium content and maximum capacity of ammonium fixation. The results showed that hydrous mica is the main 2:1 type clay mineral in <0.02 mm clay of the paddy soils, and its content in 0.02-0.002 mm clay is much higher than that in < 0.002 mm clay of the soils. The statistical analysis showed that both the fixed ammonium content and the maximum capacity of ammonium fixation of the paddy soils were positively correlated with

  3. Insensitive Ammonium Nitrate.

    Science.gov (United States)

    is reduced by replacing the ammonium nitrate with a solid solution of potassium nitrate in form III ammonium nitrate wherein the potassium nitrate...constitutes from more than zero to less than 50 weight percent of the solid solution . (Author)

  4. [Determination of di (hydrogenated tallow alkyl) dimethyl ammonium compounds in textile auxiliaries by ultra-high performance liquid chromatography-tandem mass spectrometry].

    Science.gov (United States)

    Zhu, Feng

    2015-01-01

    A method has been developed for the determination of di (hydrogenated tallow alkyl) dimethyl ammonium compounds (DHTDMAC) in textile auxiliaries by ultra-high performance liquid chromatography-tandem mass spectrometry. (UPLC-MS/MS). The samples were extracted and diluted with acidified methanol by 5% (v/v) formic acid under ultrasonic assistance. The separation was performed on an Eclipse Plus C18 column (50 mm x 2.1 mm, 1.8 microm) using 0.1% (v/v) formic acid solution and methanol as the mobile phases. Identification and quantification were achieved by UPLC-MS/MS with electrospray ionization (ESI) source in positive ion mode and multiple reaction monitoring (MRM) mode. The results indicated that the calibration curve of DHTDMAC showed good linear relationship between peak area and mass concentration in the range of 10-280 microg/L with the correlation coefficient (r2) of 0.9991. The limit of detection (LOD, S/N=3) and the limit of quantification (LOQ, S/N= 10) of this method were 3 mg/kg and 10 mg/kg, respectively. The average recoveries from three typical textile auxiliary matrices including dispersant, antistatic agent and fabric softener, at three spiked levels were in the range of 97.2%-108.3% with the relative standard deviations (RSDs) of 1.5%-4.6%. The method is sensitive, accurate, simple and effective for the analysis of DHTDMAC in textile auxiliaries.

  5. Phase Transition of Ammonium IIIite at High Temperature%铵伊利石的高温相变

    Institute of Scientific and Technical Information of China (English)

    吴红丹; 于吉顺; 张锦化; 雷新荣

    2011-01-01

    An ammonium illite sample, which was a gangue from Yangquan coal mine in Shanxi province, was investigated by Fourier transform infrared spectroscopy, electronic probe microscopic analyzer, element analyzer, thermogravimetric differential scanning calorimetry and high temperature X-ray diffraction. According to the chemical composition of the sample, the crystallographical formula calculated based on O10(OH)2 and at the total tetrahedml cations of 4 is [(NH4)0.65K0.02Na0.03Ca001]0.71[Al2.04Mg001]2.05[(Si3.14Ti0.02 Al0.84)4O10](OH)2. The structure of ammonium iilite had a good thermal stability. There are three stages for the evolution of the crystal structure with temperature. In the first stage, the structure is stable, and N from the interlayer of NH4-illite is released below 400 ℃.In the second stage, the layer thickness is reduced until the layered structure is collapsed and the TOT silicate framework can be kept in the range of 400 to 900 ℃ mainly due to the fast decomposition of [NH4]+ and de-hydroxylation. In the third stage, the semi-crystalline structure is transformed to amorphous in the range of 900 to 1 300 ℃, and the sample is re-crystallized to mullite and cristobalite.%对山西阳泉煤层黏土煤矸石中的铵伊利石进行了Fourier变换红外光谱分析、电了探针分析、元素分析、热重-差热分析和高温衍射分析.根据化学成分结果,按O10(OH)2及四面体阳离子数之和为4计算得其晶体化学式为:[(NH4)0.65K0.02Na0.03Ca0.01]0.71[Al2.04Mg0.01]2.05[Si3.14Ti0.02Al0.84)4O10](OH)2.铵伊利右的晶体结构具有较好的热稳定性,晶体结构随温度的变化分为3个阶段:400℃以前结构保持稳定,层间[NH4]+表现为缓慢释放的特征:400900℃层间[NH4]+分解,N快速释放,同时伴随着羟基脱除,表现为层间距缩小直至层状结构垮塌,伊TOT结构单元层仍保持一定的完整性,[NH4]+分解的精确温度为573℃:900~1300℃为相变阶段,铵伊利石保留的

  6. The ALICE high level trigger

    Energy Technology Data Exchange (ETDEWEB)

    Alt, T [Kirchhoff Institute for Physics, University of Heidelberg (Germany); Grastveit, G [Department of Physics and Technology, University of Bergen (Norway); Helstrup, H [Faculty of Engineering, Bergen University College (Norway); Lindenstruth, V [Kirchhoff Institute for Physics, University of Heidelberg (Germany); Loizides, C [Institute for Nuclear Physics, University of Frankfurt (Germany); Roehrich, D [Department of Physics and Technology, University of Bergen (Norway); Skaali, B [Department of Physics, University of Oslo (Norway); Steinbeck, T [Kirchhoff Institute for Physics, University of Heidelberg (Germany); Stock, R [Institute for Nuclear Physics, University of Frankfurt (Germany); Tilsner, H [Kirchhoff Institute for Physics, University of Heidelberg (Germany); Ullaland, K [Department of Physics and Technology, University of Bergen (Norway); Vestboe, A [Faculty of Engineering, Bergen University College (Norway); Vik, T [Department of Physics, University of Oslo (Norway); Wiebalck, A [Kirchhoff Institute for Physics, University of Heidelberg (Germany)

    2004-08-01

    The ALICE experiment at LHC will implement a high-level trigger system for online event selection and/or data compression. The largest computing challenge is posed by the TPC detector, which requires real-time pattern recognition. The system entails a very large processing farm that is designed for an anticipated input data stream of 25 GB s{sup -1}. In this paper, we present the architecture of the system and the current state of the tracking methods and data compression applications.

  7. Determination of diethanolamine or N-methyldiethanolamine in high ammonium concentration matrices by capillary electrophoresis with indirect UV detection: application to the analysis of refinery process waters

    Energy Technology Data Exchange (ETDEWEB)

    Bord, N.; Cretier, G.; Rocca, J.-L. [Universite Claude Bernard Lyon 1 (France). Laboratoire des Sciences Analytiques; Bailly, C. [Centre de Recherches de Gonfreville, Total France, Laboratoires Chromatographie Liquide et Microbiologie, Rogerville (France); Souchez, J.-P. [Centre de Recherches de Solaize, Total France, Chemin du Canal, BP 22, St-Symphorien d' Ozon (France)

    2004-09-01

    Alkanolamines such as diethanolamine (DEA) and N-methyldiethanolamine (MDEA) are used in desulfurization processes in crude oil refineries. These compounds may be found in process waters following an accidental contamination. The analysis of alkanolamines in refinery process waters is very difficult due to the high ammonium concentration of the samples. This paper describes a method for the determination of DEA in high ammonium concentration refinery process waters by using capillary electrophoresis (CE) with indirect UV detection. The same method can be used for the determination of MDEA. Best results were achieved with a background electrolyte (BGE) comprising 10 mM histidine adjusted to pH 5.0 with acetic acid. The development of this electrolyte and the analytical performances are discussed. The quantification was performed by using internal standardization, by which triethanolamine (TEA) was used as internal standard. A matrix effect due to the high ammonium content has been highlighted and standard addition was therefore used. The developed method was characterized in terms of repeatability of migration times and corrected peak areas, linearity, and accuracy. Limits of detection (LODs) and quantification (LOQs) obtained were 0.2 and 0.7 ppm, respectively. The CE method was applied to the determination of DEA or MDEA in refinery process waters spiked with known amounts of analytes and it gave excellent results, since uncertainties obtained were 8 and 5%, respectively. (orig.)

  8. Extraction of high-quality epidermal RNA after ammonium thiocyanate-induced dermo-epidermal separation of 4 mm human skin biopsies

    DEFF Research Database (Denmark)

    Clemmensen, Anders; Thomassen, Mads; Clemmensen, Ole;

    2009-01-01

    To obtain a separation of the epidermal and dermal compartments to examine compartment specific biological mechanisms in the skin, we incubated 4 mm human skin punch biopsies in ammonium thiocyanate. We wanted to test (i) the histological quality of the dermo-epidermal separation obtained...... was not always histologically well-defined (i.e. occurred partly intra-epidermally), but also varied between subjects. Consequently, curettage along the dermal surface of the biopsy was added to the procedure. This modified method resulted in an almost perfect separation of the epidermal and dermal compartments...... and almost completely separated from the dermis of 4 mm skin biopsies by 30 min incubation in 3.8% ammonium thiocyanate combined with curettage of the dermal surface, producing high-quality RNA suitable for transcriptional analysis. Our refined method of dermo-epidermal separation will undoubtedly prove...

  9. Phase transitions, prominent dielectric anomalies, and negative thermal expansion in three high thermally stable ammonium magnesium-formate frameworks.

    Science.gov (United States)

    Shang, Ran; Xu, Guan-Cheng; Wang, Zhe-Ming; Gao, Song

    2014-01-20

    We present three Mg-formate frameworks, incorporating three different ammoniums: [NH4][Mg(HCOO)3] (1), [CH3CH2NH3][Mg(HCOO)3] (2) and [NH3(CH2)4NH3][Mg2(HCOO)6] (3). They display structural phase transitions accompanied by prominent dielectric anomalies and anisotropic and negative thermal expansion. The temperature-dependent structures, covering the whole temperature region in which the phase transitions occur, reveal detailed structural changes, and structure-property relationships are established. Compound 1 is a chiral Mg-formate framework with the NH4(+) cations located in the channels. Above 255 K, the NH4(+) cation vibrates quickly between two positions of shallow energy minima. Below 255 K, the cations undergo two steps of freezing of their vibrations, caused by the different inner profiles of the channels, producing non-compensated antipolarization. These lead to significant negative thermal expansion and a relaxor-like dielectric response. In perovskite 2, the orthorhombic phase below 374 K possesses ordered CH3CH2NH3(+) cations in the cubic cavities of the Mg-formate framework. Above 374 K, the structure becomes trigonal, with trigonally disordered cations, and above 426 K, another phase transition occurs and the cation changes to a two-fold disordered state. The two transitions are accompanied by prominent dielectric anomalies and negative and positive thermal expansion, contributing to the large regulation of the framework coupled the order-disorder transition of CH3CH2NH3(+). For niccolite 3, the gradually enhanced flipping movement of the middle ethylene of [NH3(CH2)4NH3](2+) in the elongated framework cavity finally leads to the phase transition with a critical temperature of 412 K, and the trigonally disordered cations and relevant framework change, providing the basis for the very strong dielectric dispersion, high dielectric constant (comparable to inorganic oxides), and large negative thermal expansion. The spontaneous polarizations

  10. In situ measurement of ammonium utilization by phytoplankton in the Sacramento River to determine the impacts of high nutrient loading on the base of the food web

    Science.gov (United States)

    Schmidt, C.; Kendall, C.; Silva, S. R.; Young, M. B.

    2012-12-01

    High concentrations of ammonium in the Sacramento River and San Francisco Bay-Delta Estuary (SFE) have been hypothesized to inhibit the growth of larger phytoplankton such as diatoms, which are an important food source to zooplankton at the base of the pelagic food web. The goal of this research is to use stable isotope approaches to distinguish ammonium and nitrate utilization at the base of the food web in a range of habitats extending from freshwater portions of Sacramento River through San Pablo Bay. Preliminary results from transects sampled over a range of hydrologic conditions between 2007 and 2010 indicate shifts in the δ15N composition of the bulk particulate organic matter (POM) where ammonium concentrations increase downstream of the Sacramento Regional Wastewater Treatment Plant and again where ammonium concentrations decrease near the confluence of the Sacramento and San Joaquin Rivers. However, interpretation of δ15N of bulk POM as a proxy for δ15N of phytoplankton is complicated by the fact that the C:N ratios of bulk POM often increase to values greater than 8 downstream of the confluence of the Sacramento and San Joaquin Rivers, suggesting that in this region of the estuary bulk POM includes a significant proportion of terrestrial detrital material. Given the interest in understanding nitrogen source utilization in this portion of the estuary, work is currently underway to isolate algae from bulk POM using flow cytometry prior to isotopic analysis. δ15N vales from isolated algal samples will allow downstream changes in nutrient source utilization to be distinguished from mixing of different POM sources. Because considerable bulk POM isotopic data have been collected over the last ten years, greater understanding of the relationship between δ15N-POM and δ15N of isolated algal and terrestrial fractions will allow for improved use of the bulk POM isotope record to understand the potential link between historical changes in phytoplankton nutrient

  11. Ammonium assimilation in cyanobacteria.

    Science.gov (United States)

    Muro-Pastor, M Isabel; Reyes, Jose C; Florencio, Francisco J

    2005-01-01

    In cyanobacteria, after transport by specific permeases, ammonium is incorporated into carbon skeletons by the sequential action of glutamine synthetase (GS) and glutamate synthase (GOGAT). Two types of GS (GSI and GSIII) and two types of GOGAT (ferredoxin-GOGAT and NADH-GOGAT) have been characterized in cyanobacteria. The carbon skeleton substrate of the GS-GOGAT pathway is 2-oxoglutarate that is synthesized by the isocitrate dehydrogenase (IDH). In order to maintain the C-N balance and the amino acid pools homeostasis, ammonium assimilation is tightly regulated. The key regulatory point is the GS, which is controlled at transcriptional and posttranscriptional levels. The transcription factor NtcA plays a critical role regulating the expression of the GS and the IDH encoding genes. In the unicellular cyanobacterium Synechocystis sp. PCC 6803, NtcA controls also the expression of two small proteins (IF7 and IF17) that inhibit the activity of GS by direct protein-protein interaction. Cyanobacteria perceive nitrogen status by sensing the intracellular concentration of 2-oxoglutarate, a signaling metabolite that is able to modulate allosterically the function of NtcA, in vitro. In vivo, a functional dependence between NtcA and the signal transduction protein PII in controlling NtcA-dependent genes has been also shown.

  12. Simulated storm surge effects on freshwater coastal wetland soil porewater salinity and extractable ammonium levels: Implications for marsh recovery after storm surge

    Science.gov (United States)

    McKee, M.; White, J. R.; Putnam-Duhon, L. A.

    2016-11-01

    Coastal wetland systems experience both short-term changes in salinity, such as those caused by wind-driven tides and storm surge, and long-term shifts caused by sea level rise. Salinity increases associated with storm surge are known to have significant effects on soil porewater chemistry, but there is little research on the effect of flooding length on salt penetration depth into coastal marsh soils. A simulated storm surge was imposed on intact soil columns collected from a non-vegetated mudflat and a vegetated marsh site in the Wax Lake Delta, LA. Triplicate intact cores were continuously exposed to a 35 salinity water column (practical salinity scale) for 1, 2, and 4 weeks and destructively sampled in order to measure porewater salinity and extractable NH4sbnd N at two cm depth intervals. Salinity was significantly higher in the top 8 cm for both the marsh and mudflat cores after one week of flooding. After four weeks of flooding, salinity was significantly higher in marsh and mudflat cores compared to the control (no salinity) cores throughout the profile for both sites. Extractable ammonium levels increased significantly in the marsh cores throughout the experiment, but there was only a marginally (p coastal marsh soil in just one week. This vertical intrusion of salt can potentially negatively impact macrophytes and associated microbial communities for significantly longer term post-storm surge.

  13. High level white noise generator

    Science.gov (United States)

    Borkowski, Casimer J.; Blalock, Theron V.

    1979-01-01

    A wide band, stable, random noise source with a high and well-defined output power spectral density is provided which may be used for accurate calibration of Johnson Noise Power Thermometers (JNPT) and other applications requiring a stable, wide band, well-defined noise power spectral density. The noise source is based on the fact that the open-circuit thermal noise voltage of a feedback resistor, connecting the output to the input of a special inverting amplifier, is available at the amplifier output from an equivalent low output impedance caused by the feedback mechanism. The noise power spectral density level at the noise source output is equivalent to the density of the open-circuit thermal noise or a 100 ohm resistor at a temperature of approximately 64,000 Kelvins. The noise source has an output power spectral density that is flat to within 0.1% (0.0043 db) in the frequency range of from 1 KHz to 100 KHz which brackets typical passbands of the signal-processing channels of JNPT's. Two embodiments, one of higher accuracy that is suitable for use as a standards instrument and another that is particularly adapted for ambient temperature operation, are illustrated in this application.

  14. 除掉高浓度钼酸铵溶液中钒的研究%Remove high concentrations of vanadium in ammonium molybdate solution

    Institute of Scientific and Technical Information of China (English)

    宋夏月

    2012-01-01

    Vanadium is a process of production of ammonium molybdate impurity, high vanadium content leads to production of ammonium molybdate crystal color yellow, a direct impact on the purity of ammonium and his value. In the ammonium molybdate solution, mainly vanadium into vanadium in the form of ammonium, which can occur with the strong base anion ion exchange resin, the resin of this type of vanadium is the main tool of industrial production of vanadium is used to remove other metallurgical process vanadium as impurities tool. In the molybdenum metallurgical process, if we can make to vanadium, the use of machines to improve the value of vanadium, vanadium is also able to use from the points. In this study, nickel molybdenum is SuiDong NaYong BiJie as a raw material. Vanadium content of about 0.05%%钒是生产钼酸铵过程中的一种杂质,钒含量过高会导致生产的钼酸铵晶体颜色发黄,直接影响钼酸铵的纯度和它的使用价值。在钼酸铵溶液中,钒主要以钒酸铵的形式成在,它能与强碱性阴离子树脂发生离子交换,此类型树脂是钒工业生产钒的主要工具,也是其他冶金过程中用来除掉钒作为杂质的工具。在钼冶金过程中,如果能够把钒提出来,即提高了钒的使用价值,也能够对资源充分利用。本实验用镍钼矿为贵州毕节纳雍水东地区矿作为原料。钒含量约为0.05%。

  15. Synergetic stress of acids and ammonium on the shift in the methanogenic pathways during thermophilic anaerobic digestion of organics.

    Science.gov (United States)

    Lü, Fan; Hao, Liping; Guan, Dongxing; Qi, Yujiao; Shao, Liming; He, Pinjing

    2013-05-01

    Combined effects of acids and ammonium on functional pathway and microbial structure during organics methanization were investigated by stable isotopic method and quantitative PCR. The results showed that the stress from acids and ammonium was synergetic, resulted in different inhibition for acetoclastic and hydrogenotrophic methanogenesis and syntrophic acetate oxidation, leading to pathway shift. Methane production from acetate was affected more by acetate than by ammonium until the ammonium concentration reached 6-7 g-N/L. When the ammonium concentration exceeded 6 g-N/L, ammonium inhibition was strengthened by the increased concentration of acetate. At a low acetate concentration (50 mmol/L), acetoclastic methanogenesis dominated, regardless of ammonium concentration. At higher acetate concentrations (150 and 250 mmol/L) and at low-medium ammonium levels (1-4 g-N/L), acetate was mainly degraded by acetoclastic methanogenesis, while residual acetate was degraded by a combination of acetoclastic methanogenesis and the syntrophic reaction of syntrophic acetate oxidization and hydrogenotrophic methanogenesis with the latter dominating at 250 mmol/L acetate. At high ammonium levels (6-7 g-N/L), the degradation of acetate in the 150 mmol/L treatment was firstly through a combination of acetoclastic methanogenesis and the syntrophic pathway and then gradually shifted to the syntrophic pathway, while the degradation of acetate in the 250 mmol/L treatment was completely by the syntrophic pathway.

  16. A General, Simple Catalyst for Enantiospecific Cross Couplings of Benzylic Ammonium Triflates and Boronic Acids: No Phosphine Ligand Required

    Science.gov (United States)

    Basch, Corey H.; Song, Ye-Geun; Watson, Mary P.

    2014-01-01

    Highly improved conditions for the enantiospecific cross coupling of benzylic ammonium triflates with boronic acids are reported. This method relies on the use of Ni(cod)2 without ancillary phosphine or N-heterocyclic carbene ligands as catalyst. These conditions enable the coupling of new classes of boronic acids and benzylic ammonium triflates. In particular, both heteroaromatic and vinyl boronic acids are well tolerated as coupling partners. In addition, these conditions enable the use of ammonium triflates with a variety of substituents at the benzylic stereocenter. Further, naphthyl-substitution is not required on the benzylic ammonium triflate; ammonium triflates with simple aromatic substituents also undergo this coupling. Good to high yields and levels of stereochemical fidelity are observed. This new catalyst system greatly expands the utility of enantiospecific cross couplings of these amine-derived substrates for the preparation of highly enantioenriched products. PMID:25364060

  17. Over-expression of OsPTR6 in rice increased plant growth at different nitrogen supplies but decreased nitrogen use efficiency at high ammonium supply.

    Science.gov (United States)

    Fan, Xiaorong; Xie, Dan; Chen, Jingguang; Lu, Haiyan; Xu, Yanling; Ma, Cui; Xu, Guohua

    2014-10-01

    Nitrogen (N) plays a critical role in plant growth and productivity and PTR/NRT1 transporters are critical for rice growth. In this study, OsPTR6, a PTR/NRT1 transporter, was over-expressed in the Nipponbare rice cultivar by Agrobacterium tumefaciens transformation using the ubiquitin (Ubi) promoter. Three single-copy T2 generation transgenic lines, named OE1, OE5 and OE6, were produced and subjected to hydroponic growth experiments in different nitrogen treatments. The results showed the plant height and biomass of the over-expression lines were increased, and plant N accumulation and glutamine synthetase (GS) activities were enhanced at 5.0mmol/L NH4(+) and 2.5mmol/L NH4NO3. The expression of OsATM1 genes in over-expression lines showed that the OsPTR6 over expression increased OsAMT1.1, OsATM1.2 and OsAMT1.3 expression at 0.2 and 5.0mmol/L NH4(+) and 2.5mmol/L NH4NO3. However, nitrogen utilisation efficiency (NUE) was decreased at 5.0mmol/LNH4(+). These data suggest that over-expression of the OsPTR6 gene could increase rice growth through increasing ammonium transporter expression and glutamine synthetase activity (GSA), but decreases nitrogen use efficiency under conditions of high ammonium supply.

  18. 氧化镁铵盐法制备高纯过氧化镁%Preparation of High Purity Magnesium Peroxide by Magnesia and Ammonium Salt Solutions

    Institute of Scientific and Technical Information of China (English)

    朱海丽; 吴小王

    2011-01-01

    在氯化铵溶液体系中,以氧化镁,过氧化氢为原料,制备高纯过氧化镁。研究表明采用氧化镁活性大于100,氯化铵/氧化镁不小于10%,过氧化氢:氧化镁不小于4∶1,反应温度大于40℃情况下,反应时间不小于30 min,可制备出纯度大于90%的过氧化镁。%In ammonium chloride solution,magnesium oxide and hydrogen peroxide as raw material,high purity magnesium peroxide was prepared.The results showed that using magnesium oxide activity was greater than 100,ammonium chloride and magnesium oxide was not less than 10%,hydrogen peroxide to magnesium oxide was not less than 4:1,the reaction temperature was higher than 40 ℃,and the reaction time was not less than 30 min,with magnesium peroxide purity above 90%.

  19. Ammonium Lactate Topical

    Science.gov (United States)

    ... are pregnant, plan to become pregnant, or are breastfeeding. If you become pregnant while using ammonium lactate, call your doctor.plan to avoid unnecessary or prolonged exposure to natural or artificial sunlight to the affected skin area and to ...

  20. 新型高威力含铝硝铵炸药的研究%A New High Strength Ammonium Nitrate Powdery Explosive Containing Aluminium

    Institute of Scientific and Technical Information of China (English)

    陆明; 吕春绪; 刘祖亮

    2001-01-01

    A new type high strength ammonium nitrate powdery explosive containing aluminium is manufactured by mixing oxidizer, a kind of expanded ammonium nitrate, which possesses many microholes and self-sensitivity, with reducing agent, which is the mixture of wood powder, composite fuel oil and aluminium powder. By mathematical model for prescription design and optimization of the industrial explosive which contains chemical elements such as C,H,O,N,Al and experimental research, a good prescription of powdery ammonium nitrate explosive containing aluminium powder is obtained, the formulation is expanded ammonium nitrate 85.5 %~89.5 %, wood powder 3.5 %~4.5 %,composite fuel oil 2.0 %~3.0 %,aluminium powder 5.0 %~7.0 %. The explosion property parameters of this kind of commercial explosive are detonation velocity (32 mm)3 600~3 800 m/s,brisance 16.00~17.00 mm, sensitivity to initial detonation 12~14 cm, strength 370~390 mL,charge density 0.92~0.95 g/cm3. The relation between the amount of aluminium power in explosive and explosion property is also discussed in this paper, when the amount of aluminium power in ammonium nitrate explosive is 6.5 %~7.0 %,the strength arrives maximum.%该文以一种含有大量微气泡、自身敏化的膨化硝酸铵为氧化剂,以木粉、燃料油和铝粉为还原剂,制成新型高威力含铝硝铵炸药。通过建构含C、H、O、N、Al元素工业炸药配方设计及最优化的数学模型,计算得到含铝硝铵炸药的较佳配方为硝酸铵85.5 %~89.5 %、木粉3.5 %~4.5 %、复合油相2.0 %~3.0 %、铝粉5.0 %~7.0 %。该炸药的爆炸性能为:装药密度0.91~95 g/cm3,爆速3 600~3 800 m/s,殉爆距离12~14 cm,猛度16~17 mm,作功能力370~390 mL。文中还讨论了含铝硝铵炸药中铝粉含量与爆炸性能的关系

  1. Growth, morphology, ammonium uptake and nutrient allocation of Myriophyllum brasiliense Cambess. under high NH₄⁺ concentrations.

    Science.gov (United States)

    Saunkaew, Piyanart; Wangpakapattanawong, Prasit; Jampeetong, Arunothai

    2011-11-01

    The effects of high NH(4)(+) concentration on growth, morphology, NH(4) (+) uptake and nutrient allocation of Myriophyllum brasiliense were investigated in hydroponic culture. The plants were grown under greenhouse conditions for 4 weeks using four levels of NH(4)(+) concentration: 1, 5, 10 and 15 mM. M. brasiliense grew well with a relative growth rate of c.0.03 day(-1) at NH(4)(+) concentration up to 5 mM. At the higher NH(4)(+) concentrations the growth of the plants was stunted and the plants had short roots and few new buds, especially when grown in 15 mM NH(4)(+) where the submerged leaves were lost and there were rotten roots and submerged stems. To avoid NH(4)(+) toxicity, the plants may have a mechanism to prevent cytoplasmic NH(4)(+) accumulation in plant cells. The net uptake of NH(4)(+) significantly decreased and the total N significantly increased in the plants treated with 10 and 15 mM NH(4)(+), respectively. The plant may employ NH(4)(+) assimilation and extrusion as a mechanism to compensate for the high NH(4)(+) concentrations. However, the plants may show nutrient deficiency symptoms, especially K deficiency symptoms, after they were exposed to NH(4)(+) concentration higher than 10 mM. The present study provides a basic ecophysiology of M. brasiliense that it can grow in NH(4)(+) enriched water up to concentrations as high as 5 mM.

  2. Modification of zeolities with ammonium fluoride

    Energy Technology Data Exchange (ETDEWEB)

    Rosinski, E.J.

    1988-05-17

    A method for enhancing the shape selectivity and adjusting catalytic activity of a crystalline zeolite, including a highly siliceous zeolite, is disclosed. Such a method involves contacting the zeolite with an ammonium fluoride solution in the absence of an aluminum source, optionally contacting the treated zeolite with a warm aqueous solution of an ammonium salt, and then calcining the fluoride and ammonium treated zeolite to produce a more shape selective zeolite material. Such treated zeolite are useful in catalysts which promote shape selective conversion of organic compounds including, for example, hydrocarbon cracking reactions.

  3. High-level language computer architecture

    CERN Document Server

    Chu, Yaohan

    1975-01-01

    High-Level Language Computer Architecture offers a tutorial on high-level language computer architecture, including von Neumann architecture and syntax-oriented architecture as well as direct and indirect execution architecture. Design concepts of Japanese-language data processing systems are discussed, along with the architecture of stack machines and the SYMBOL computer system. The conceptual design of a direct high-level language processor is also described.Comprised of seven chapters, this book first presents a classification of high-level language computer architecture according to the pr

  4. Phase diagram of ammonium nitrate

    Science.gov (United States)

    Dunuwille, M.; Yoo, C. S.

    2014-05-01

    Ammonium Nitrate (AN) has often subjected to uses in improvised explosive devices, due to its wide availability as a fertilizer and its capability of becoming explosive with slight additions of organic and inorganic compounds. Yet, the origin of enhanced energetic properties of impure AN (or AN mixtures) is neither chemically unique nor well understood -resulting in rather catastrophic disasters in the past1 and thereby a significant burden on safety in using ammonium nitrates even today. To remedy this situation, we have carried out an extensive study to investigate the phase stability of AN at high pressure and temperature, using diamond anvil cells and micro-Raman spectroscopy. The present results confirm the recently proposed phase IV-to-IV' transition above 17 GPa2 and provide new constraints for the melting and phase diagram of AN to 40 GPa and 400 °C.

  5. A river-scale Lagrangian experiment examining controls on phytoplankton dynamics in the presence and absence of treated wastewater effluent high in ammonium

    Science.gov (United States)

    Kraus, Tamara; Carpenter, Kurt; Bergamaschi, Brian; Parker, Alexander; Stumpner, Elizabeth; Downing, Bryan D.; Travis, Nicole; Wilkerson, Frances; Kendall, Carol; Mussen, Timothy

    2017-01-01

    Phytoplankton are critical component of the food web in most large rivers and estuaries, and thus identifying dominant controls on phytoplankton abundance and species composition is important to scientists, managers, and policymakers. Recent studies from a variety of systems indicate that ammonium ( NH+4) in treated wastewater effluent decreases primary production and alters phytoplankton species composition. However, these findings are based mainly on laboratory and enclosure studies, which may not adequately represent natural systems. To test effects of effluent high in ammonium on phytoplankton at the ecosystem scale, we conducted whole-river–scale experiments by halting discharges to the Sacramento River from the regional wastewater treatment plant (WWTP), and used a Lagrangian approach to compare changes in phytoplankton abundance and species composition in the presence (+EFF) and absence (−EFF) of effluent. Over 5 d of downstream travel from 20 km above to 50 km below the WWTP, chlorophyll concentrations declined from 15–25 to ∼2.5 μg L−1, irrespective of effluent addition. Benthic diatoms were dominant in most samples. We found no significant difference in phytoplankton abundance or species composition between +EFF and −EFF conditions. Moreover, greatest declines in chlorophyll occurred upstream of the WWTP where NH+4 concentrations were low. Grazing by clams and zooplankton could not account for observed losses, suggesting other factors such as hydrodynamics and light limitation were responsible for phytoplankton declines. These results highlight the advantages of conducting ecosystem-scale, Lagrangian-based experiments to understand the dynamic and complex interplay between physical, chemical, and biological factors that control phytoplankton populations.

  6. Ecological functions of ciliated protozoa in marine ecosystem: effects of ammonium on the population growth of Euplotes vannus

    Institute of Scientific and Technical Information of China (English)

    Xu Henglong; Song Weibo; Zhu Mingzhuang; Wang Mei; Ma Honggang; Xu Xiaozhong

    2005-01-01

    The effects of ammonium on the population growth of the marine ciliate, Euplotes vannus, were examined using ecotoxicological method. It is showed that ammonium exerts inhibitory effects on the growth of the ciliate populations in a concentration-dependent way. Statistical analysis reveals that the population growth dynamics exposed to ammonium-N concentration over 100mg/L are significantly different from that in the control at P<0.05 level. Linear regression determined that the 24h, 36h, 48h, 60h, 72h and 84h IC50 values of ammonium-N are 19.68, 201.51, 167.49, 47.86, 50.43 and 43.11 concentration over 100mg/L, respectively (P<0.05; pH 8.2; salinity 28 ppt; temperature, 25℃). The results indicate that the tolerance to ammonium in E. vannus is considerably higher than that of the larvae or juveniles of some metozoa, such as cultured prawns and oysters. Therefore, it is believed that the high tolerance to ammonium is necessary for ciliated protozoa to play positive roles in maintaining and improving water quality in marine ecosystems, especially in the intensive aquaculture waters with high-level ammonium. In addition, the correlation between IC50 values and exposure time was discussed.

  7. Stability enhancement of PbSe quantum dots via post-synthetic ammonium chloride treatment for a high-performance infrared photodetector.

    Science.gov (United States)

    Fu, Chunjie; Wang, Haowei; Song, Taojian; Zhang, Li; Li, Weile; He, Bo; sulaman, Muhammad; Yang, Shengyi; Zou, Bingsuo

    2016-02-12

    Infrared (IR) emission lead selenide (PbSe) quantum dots (QDs) have gained considerable attention in the last decade due to their potential applications in optoelectronic devices. However, the comprehensive applications of PbSe QDs have not been realized yet due to their high susceptibility to oxidation in air. In this paper, we demonstrate the stability enhancement of PbSe colloidal QDs via a post-synthetic ammonium chloride treatment and its applications in a solution-processed high-performance IR photodetector with a field-effect transistor (FET) configuration by reversely fabricating the PbSe active layer and polymethylmethacrylate (PMMA) dielectric layer. The responsivity and the specific detectivity of the FET-based photodetector Au(source, drain)/PbSe(52 nm)/PMMA(930 nm)/Au(gate) reached 64.17 mA W(-1) and 5.08 × 10(10) Jones, respectively, under 980 nm laser illumination with an intensity of 0.1 mW cm(-2). Therefore, it provides a promising way to make a high-sensitivity near-IR/mid-IR photodetector.

  8. Stability enhancement of PbSe quantum dots via post-synthetic ammonium chloride treatment for a high-performance infrared photodetector

    Science.gov (United States)

    Fu, Chunjie; Wang, Haowei; Song, Taojian; Zhang, Li; Li, Weile; He, Bo; sulaman, Muhammad; Yang, Shengyi; Zou, Bingsuo

    2016-02-01

    Infrared (IR) emission lead selenide (PbSe) quantum dots (QDs) have gained considerable attention in the last decade due to their potential applications in optoelectronic devices. However, the comprehensive applications of PbSe QDs have not been realized yet due to their high susceptibility to oxidation in air. In this paper, we demonstrate the stability enhancement of PbSe colloidal QDs via a post-synthetic ammonium chloride treatment and its applications in a solution-processed high-performance IR photodetector with a field-effect transistor (FET) configuration by reversely fabricating the PbSe active layer and polymethylmethacrylate (PMMA) dielectric layer. The responsivity and the specific detectivity of the FET-based photodetector Au(source, drain)/PbSe(52 nm)/PMMA(930 nm)/Au(gate) reached 64.17 mA W-1 and 5.08 × 1010 Jones, respectively, under 980 nm laser illumination with an intensity of 0.1 mW cm-2. Therefore, it provides a promising way to make a high-sensitivity near-IR/mid-IR photodetector.

  9. SIGWX Charts - High Level Significant Weather

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — High level significant weather (SIGWX) forecasts are provided for the en-route portion of international flights. NOAA's National Weather Service Aviation Center...

  10. High-Level Dialogue on International Migration

    Directory of Open Access Journals (Sweden)

    UNHCR

    2006-08-01

    Full Text Available UNHCR wishes to bring the following observations andrecommendations to the attention of the High-LevelDialogue (HLD on International Migration and Development,to be held in New York, 14-15 September 2006:

  11. High-level binocular rivalry effects.

    Science.gov (United States)

    Wolf, Michal; Hochstein, Shaul

    2011-01-01

    Binocular rivalry (BR) occurs when the brain cannot fuse percepts from the two eyes because they are different. We review results relating to an ongoing controversy regarding the cortical site of the BR mechanism. Some BR qualities suggest it is low-level: (1) BR, as its name implies, is usually between eyes and only low-levels have access to utrocular information. (2) All input to one eye is suppressed: blurring doesn't stimulate accommodation; pupilary constrictions are reduced; probe detection is reduced. (3) Rivalry is affected by low-level attributes, contrast, spatial frequency, brightness, motion. (4) There is limited priming due to suppressed words or pictures. On the other hand, recent studies favor a high-level mechanism: (1) Rivalry occurs between patterns, not eyes, as in patchwork rivalry or a swapping paradigm. (2) Attention affects alternations. (3) Context affects dominance. There is conflicting evidence from physiological studies (single cell and fMRI) regarding cortical level(s) of conscious perception. We discuss the possibility of multiple BR sites and theoretical considerations that rule out this solution. We present new data regarding the locus of the BR switch by manipulating stimulus semantic content or high-level characteristics. Since these variations are represented at higher cortical levels, their affecting rivalry supports high-level BR intervention. In Experiment I, we measure rivalry when one eye views words and the other non-words and find significantly longer dominance durations for non-words. In Experiment II, we find longer dominance times for line drawings of simple, structurally impossible figures than for similar, possible objects. In Experiment III, we test the influence of idiomatic context on rivalry between words. Results show that generally words within their idiomatic context have longer mean dominance durations. We conclude that BR has high-level cortical influences, and may be controlled by a high-level mechanism.

  12. The mechanical properties of the ultra high molecular weight polyethylene grafted with 3-dimethy (3-(N-methacryamido) propyl) ammonium propane sulfonate.

    Science.gov (United States)

    Deng, Yaling; Xiong, Dangsheng; Wang, Kun

    2014-07-01

    Ultra-high molecular weight polyethylene (UHMWPE) powder was modified with a zwitterion monomer with good biocompatibility of MPDSAH (3-dimethy (3-(N-methacryamido) propyl) ammonium propane sulfonate) by UV irradiation and then hot pressed. The microstructure and mechanical properties of modified UHMWPE are investigated. The results show that the structure of powder and bulk materials has been changed. The modified powders have more filaments than that of untreated. The surface of modified bulk materials is more rough and displays the granular protuberances which have the random loose arrangement compared with untreated UHMWPE. The crystallinity, uniaxial tensile and compressive properties decreased after grafting. Ultimate elongations decrease with the increase of the monomer concentration and are higher than 300% which is recommended by ASTM and ISO except the sample with 0.45mol/L MPDSAH. The friction coefficient of modified UHMWPE is lower than that of the untreated UHMWPE and it decreases gradually with the increase of monomer concentration. The wear rates have been decreased and the wear resistance has been improved under saline and distilled water lubrication.

  13. High temperature thermal stability investigations of ammonium sulphide passivated InGaAs and interface formation with Al{sub 2}O{sub 3} studied by synchrotron radiation based photoemission

    Energy Technology Data Exchange (ETDEWEB)

    Chauhan, Lalit, E-mail: lalit.chauhan2@mail.dcu.ie [School of Physical Sciences, Dublin City University, Glasnevin, Dublin 9 (Ireland); Gajula, Durga Rao; McNeill, David [School of Electronics, Electrical Engineering and Computer Science, Queen' s University Belfast (United Kingdom); Hughes, Greg [School of Physical Sciences, Dublin City University, Glasnevin, Dublin 9 (Ireland)

    2014-10-30

    Highlights: • Sulphur passivation is effective at removing the native oxides from InGaAs surface. • A 700°C anneal of the sulphur passivated surface at leads to the loss of indium. • A 1 nm Al2O3 layer improves the thermal stability of the sulphur passivated InGaAs. - Abstract: High resolution synchrotron radiation core level photoemission measurements have been used to undertake a comparative study of the high temperature thermal stability of the ammonium sulphide passivated InGaAs surface and the same surface following the atomic layer deposition (ALD) of an ultrathin (∼1 nm) Al{sub 2}O{sub 3} layer. The solution based ex situ sulphur passivation was found to be effective at removing a significant amount of the native oxides and protecting the surface against re-oxidation upon air exposure. The residual interfacial oxides which form between sulphur passivated InGaAs and the ultrathin Al{sub 2}O{sub 3} layer can be substantially removed at high temperature (up to 700°C) without impacting on the InGaAs stoichiometry while significant loss of indium was recorded at this temperature on the uncovered sulphur passivated InGaAs surface.

  14. EAP high-level product architecture

    DEFF Research Database (Denmark)

    Guðlaugsson, Tómas Vignir; Mortensen, Niels Henrik; Sarban, Rahimullah

    2013-01-01

    the function of the EAP transducers to be changed, by basing the EAP transducers on a different combination of organ alternatives. A model providing an overview of the high level product architecture has been developed to support daily development and cooperation across development teams. The platform approach...... of EAP technology products while keeping complexity under control. High level product architecture has been developed for the mechanical part of EAP transducers, as the foundation for platform development. A generic description of an EAP transducer forms the core of the high level product architecture....... Initial results from applying the platform on demonstrator design for potential applications are promising. The scope of the article does not include technical details. © 2013 SPIE....

  15. Resistance of Pseudomonas to Quaternary Ammonium Compounds. I. Growth in Benzalkonium Chloride Solution

    Science.gov (United States)

    Adair, Frank W.; Geftic, Sam G.; Gelzer, Justus

    1969-01-01

    Resistant cells of Pseudomonas aeruginosa and a waterborne Pseudomonas sp. (strain Z-R) were able to multiply in nitrogen-free minimal salts solution containing various concentrations of commercially prepared, ammonium acetate-buffered benzalkonium chloride (CBC), a potent antimicrobial agent. As the CBC concentration increased, growth increased until a point was reached at which the extent of growth leveled off or was completely depressed. Minimal salts solutions of pure benzalkonium chloride (PBC) containing no ammonium acetate did not support bacterial growth. When ammonium acetate was added to PBC solutions in the same concentrations found in CBC solutions, growth patterns developed that were comparable to those found with CBC. Likewise, (NH4)2SO4 added to PBC solutions supported growth of both organisms. P. aeruginosa was initially resistant to CBC levels of 0.02% and it was adapted to tolerate levels as high as 0.36%. Strain Z-R was naturally resistant to 0.4% CBC. Since ammonium acetate, carried over by the CBC used in drug formulations and disinfectant solutions, has the potential to support the growth of resistant bacteria and thus make possible the risk of serious infection, it is suggested that regulations allowing the presence of ammonium acetate in CBC solution be reconsidered. PMID:4984761

  16. Selective determination of ammonium ions by high-speed ion-exclusion chromatography on a weakly basic anion-exchange resin column.

    Science.gov (United States)

    Mori, Masanobu; Tanaka, Kazuhiko; Helaleh, Murad I H; Xu, Qun; Ikedo, Mikaru; Ogura, Yutaka; Sato, Shinji; Hu, Wenzhi; Hasebe, Kiyoshi

    2003-05-16

    This paper describes an ion-exclusion chromatographic system for the rapid and selective determination of ammonium ion. The optimized ion-exclusion chromatographic system was established with a polymethacrylate-based weakly basic anion-exchange resin column (TSKgel DEAE-5PW) as the separation column, an aqueous solution containing 0.05 mM tetramethylammonium hydroxide (pH 9.10) as eluent with conductimetric detection for the analyte determination. Under the optimum chromatographic conditions, ammonium ion was determined within 2.3 min with a detection limit (S/N=3) better than 0.125 microM. Ammonium ion in rain and river waters was precisely determined using this ion-exclusion chromatographic system.

  17. Long-term performance of side-stream deammonification in a continuous flow granular-activated sludge process for nitrogen removal from high ammonium wastewater.

    Science.gov (United States)

    Rezania, Babak; Mavinic, Donald S; Kelly, Harlan G

    2015-01-01

    An innovative granular sludge deammonification system was incorporated into a conventional-activated sludge process. The process incorporated an internal baffle in the bioreactor for continuous separation of granular biomass from flocculent biomass, which allowed for controlling the solids retention time of flocculent sludge. The process was evaluated for ammonium removal from municipal digested sludge dewatering centrate under various operating conditions lasting over 450 days. The process successfully removed, on average, 90% of the ammonium from centrate at various ammonium loading reaching 1.4 kg/m³d at 20 hours hydraulic retention time. Controlling the retention time of the flocculent biomass and maintaining low nitrite concentration were both found to be effective for nitrite oxidizing bacteria management, resulting in a low nitrate concentration (below 50 mg/L) over a wide range of flocculent biomass concentration in the bioreactor.

  18. PAIRWISE BLENDING OF HIGH LEVEL WASTE (HLW)

    Energy Technology Data Exchange (ETDEWEB)

    CERTA, P.J.

    2006-02-22

    The primary objective of this study is to demonstrate a mission scenario that uses pairwise and incidental blending of high level waste (HLW) to reduce the total mass of HLW glass. Secondary objectives include understanding how recent refinements to the tank waste inventory and solubility assumptions affect the mass of HLW glass and how logistical constraints may affect the efficacy of HLW blending.

  19. High spin levels in /sup 151/Ho

    Energy Technology Data Exchange (ETDEWEB)

    Gizon, J.; Gizon, A.; Andre, S.; Genevey, J.; Jastrzebski, J.; Kossakowski, R.; Moszynski, M.; Preibisz, Z.

    1981-07-01

    We report here on the first study of the level structure of /sup 151/Ho. High spin levels in /sup 151/Ho have been populated in the /sup 141/Pr + /sup 16/O and /sup 144/Sm + /sup 12/C reactions. The level structure has been established up to 6,6 MeV energy and the spins and parities determined up to 49/2/sup -/. Most of the proposed level configurations can be explained by the coupling of h sub(11/2) protons to fsub(7/2) and/or hsub(9/2) neutrons. An isomer with 14 +- 3 ns half-life and a delayed gamma multiplicity equal to 17 +- 2 has been found. Its spin is larger than 57/2 h units.

  20. High spin levels in /sup 151/Ho

    Energy Technology Data Exchange (ETDEWEB)

    Gizon, J.; Gizon, A.; Andre, S.; Genevey, J.; Jastrzebski, J.; Kossakowski, R.; Moszynski, M.; Preibisz, Z.

    1981-07-01

    We report here on the first study of the level structure of /sup 151/Ho. High spin levels in /sup 151/Ho have been populated in the /sup 141/Pr + /sup 16/O and /sup 144/Sm + /sup 12/C reactions. The level structure has been established up to 6.6 MeV energy and the spins and parities determined up to 49/2/sup -/. Most of the proposed level configurations can be explained by the coupling of hsub(11/2) protons to fsub(7/2) and/or hsub(9/2) neutrons. An isomer with 14 +- 3 ns half-life and a delayed gamma multiplicity equal 17 +- 2 has been found. Its spin is larger than 57/2 h units.

  1. Pore mutations in ammonium transporter AMT1 with increased electrogenic ammonium transport activity.

    Science.gov (United States)

    Loqué, Dominique; Mora, Silvia I; Andrade, Susana L A; Pantoja, Omar; Frommer, Wolf B

    2009-09-11

    AMT/Mep ammonium transporters mediate high affinity ammonium/ammonia uptake in bacteria, fungi, and plants. The Arabidopsis AMT1 proteins mediate uptake of the ionic form of ammonium. AMT transport activity is controlled allosterically via a highly conserved cytosolic C terminus that interacts with neighboring subunits in a trimer. The C terminus is thus capable of modulating the conductivity of the pore. To gain insight into the underlying mechanism, pore mutants suppressing the inhibitory effect of mutations in the C-terminal trans-activation domain were characterized. AMT1;1 carrying the mutation Q57H in transmembrane helix I (TMH I) showed increased ammonium uptake but reduced capacity to take up methylammonium. To explore whether the transport mechanism was altered, the AMT1;1-Q57H mutant was expressed in Xenopus oocytes and analyzed electrophysiologically. AMT1;1-Q57H was characterized by increased ammonium-induced and reduced methylammonium-induced currents. AMT1;1-Q57H possesses a 100x lower affinity for ammonium (K(m)) and a 10-fold higher V(max) as compared with the wild type form. To test whether the trans-regulatory mechanism is conserved in archaeal homologs, AfAmt-2 from Archaeoglobus fulgidus was expressed in yeast. The transport function of AfAmt-2 also depends on trans-activation by the C terminus, and mutations in pore-residues corresponding to Q57H of AMT1;1 suppress nonfunctional AfAmt-2 mutants lacking the activating C terminus. Altogether, our data suggest that bacterial and plant AMTs use a conserved allosteric mechanism to control ammonium flux, potentially using a gating mechanism that limits flux to protect against ammonium toxicity.

  2. Transcriptional Analysis of an Ammonium-Excreting strain of Azotobacter vinelandii Deregulated for Nitrogen Fixation.

    Science.gov (United States)

    Barney, Brett M; Plunkett, Mary H; Natarajan, Velmurugan; Mus, Florence; Knutson, Carolann M; Peters, John W

    2017-08-11

    Biological nitrogen fixation is accomplished by a diverse group of organisms known as diazotrophs, and requires the function of the complex metalloenzyme nitrogenase. Nitrogenase and many of the accessory proteins required for proper cofactor biosynthesis and incorporation into the enzyme have been characterized, but a complete picture of the reaction mechanism and key cellular changes that accompany biological nitrogen fixation remain to be fully elucidated. Studies have revealed that specific disruptions to the anti-activator encoding gene nifL result in the deregulation of the nif transcriptional activator NifA in the nitrogen-fixing bacterium Azotobacter vinelandii, triggering the production of extracellular ammonium levels approaching 30 mM during the stationary phase of growth. In this work, we have characterized the global patterns of gene expression of this high-ammonium releasing phenotype. The findings reported here indicated that cultures of this high-ammonium accumulating strain may be experiencing metal limitation when grown using standard Burk's medium, which could be amended by increasing molybdenum levels to further increase ammonium yield. In addition, elevated levels of nitrogenase gene transcription are not accompanied by a corresponding dramatic increase in hydrogenase gene transcription, or hydrogen uptake rates. Of the three potential electron donor systems for nitrogenase, only the rnf1 gene cluster showed a transcriptional correlation to the increased yield of ammonium. Our results also highlight several additional genes which may play a role in supporting elevated ammonium production in this aerobic nitrogen-fixing model bacterium.Importance: The transcriptional differences found during stationary-phase ammonium accumulation show a strong contrast between the deregulated (nifL disrupted) and wild-type strain, and to what was previously reported for the wild-type strain during exponential phase growth conditions. These results demonstrate

  3. Python based high-level synthesis compiler

    Science.gov (United States)

    Cieszewski, Radosław; Pozniak, Krzysztof; Romaniuk, Ryszard

    2014-11-01

    This paper presents a python based High-Level synthesis (HLS) compiler. The compiler interprets an algorithmic description of a desired behavior written in Python and map it to VHDL. FPGA combines many benefits of both software and ASIC implementations. Like software, the mapped circuit is flexible, and can be reconfigured over the lifetime of the system. FPGAs therefore have the potential to achieve far greater performance than software as a result of bypassing the fetch-decode-execute operations of traditional processors, and possibly exploiting a greater level of parallelism. Creating parallel programs implemented in FPGAs is not trivial. This article describes design, implementation and first results of created Python based compiler.

  4. SNPs altering ammonium transport activity of human Rhesus factors characterized by a yeast-based functional assay.

    Directory of Open Access Journals (Sweden)

    Aude Deschuyteneer

    Full Text Available Proteins of the conserved Mep-Amt-Rh family, including mammalian Rhesus factors, mediate transmembrane ammonium transport. Ammonium is an important nitrogen source for the biosynthesis of amino acids but is also a metabolic waste product. Its disposal in urine plays a critical role in the regulation of the acid/base homeostasis, especially with an acid diet, a trait of Western countries. Ammonium accumulation above a certain concentration is however pathologic, the cytotoxicity causing fatal cerebral paralysis in acute cases. Alteration in ammonium transport via human Rh proteins could have clinical outcomes. We used a yeast-based expression assay to characterize human Rh variants resulting from non synonymous single nucleotide polymorphisms (nsSNPs with known or unknown clinical phenotypes and assessed their ammonium transport efficiency, protein level, localization and potential trans-dominant impact. The HsRhAG variants (I61R, F65S associated to overhydrated hereditary stomatocytosis (OHSt, a disease affecting erythrocytes, proved affected in intrinsic bidirectional ammonium transport. Moreover, this study reveals that the R202C variant of HsRhCG, the orthologue of mouse MmRhcg required for optimal urinary ammonium excretion and blood pH control, shows an impaired inherent ammonium transport activity. Urinary ammonium excretion was RHcg gene-dose dependent in mouse, highlighting MmRhcg as a limiting factor. HsRhCG(R202C may confer susceptibility to disorders leading to metabolic acidosis for instance. Finally, the analogous R211C mutation in the yeast ScMep2 homologue also impaired intrinsic activity consistent with a conserved functional role of the preserved arginine residue. The yeast expression assay used here constitutes an inexpensive, fast and easy tool to screen nsSNPs reported by high throughput sequencing or individual cases for functional alterations in Rh factors revealing potential causal variants.

  5. SNPs altering ammonium transport activity of human Rhesus factors characterized by a yeast-based functional assay.

    Science.gov (United States)

    Deschuyteneer, Aude; Boeckstaens, Mélanie; De Mees, Christelle; Van Vooren, Pascale; Wintjens, René; Marini, Anna Maria

    2013-01-01

    Proteins of the conserved Mep-Amt-Rh family, including mammalian Rhesus factors, mediate transmembrane ammonium transport. Ammonium is an important nitrogen source for the biosynthesis of amino acids but is also a metabolic waste product. Its disposal in urine plays a critical role in the regulation of the acid/base homeostasis, especially with an acid diet, a trait of Western countries. Ammonium accumulation above a certain concentration is however pathologic, the cytotoxicity causing fatal cerebral paralysis in acute cases. Alteration in ammonium transport via human Rh proteins could have clinical outcomes. We used a yeast-based expression assay to characterize human Rh variants resulting from non synonymous single nucleotide polymorphisms (nsSNPs) with known or unknown clinical phenotypes and assessed their ammonium transport efficiency, protein level, localization and potential trans-dominant impact. The HsRhAG variants (I61R, F65S) associated to overhydrated hereditary stomatocytosis (OHSt), a disease affecting erythrocytes, proved affected in intrinsic bidirectional ammonium transport. Moreover, this study reveals that the R202C variant of HsRhCG, the orthologue of mouse MmRhcg required for optimal urinary ammonium excretion and blood pH control, shows an impaired inherent ammonium transport activity. Urinary ammonium excretion was RHcg gene-dose dependent in mouse, highlighting MmRhcg as a limiting factor. HsRhCG(R202C) may confer susceptibility to disorders leading to metabolic acidosis for instance. Finally, the analogous R211C mutation in the yeast ScMep2 homologue also impaired intrinsic activity consistent with a conserved functional role of the preserved arginine residue. The yeast expression assay used here constitutes an inexpensive, fast and easy tool to screen nsSNPs reported by high throughput sequencing or individual cases for functional alterations in Rh factors revealing potential causal variants.

  6. DUACS: Toward High Resolution Sea Level Products

    Science.gov (United States)

    Faugere, Y.; Gerald, D.; Ubelmann, C.; Claire, D.; Pujol, M. I.; Antoine, D.; Desjonqueres, J. D.; Picot, N.

    2016-12-01

    The DUACS system produces, as part of the CNES/SALP project, and the Copernicus Marine Environment and Monitoring Service, high quality multimission altimetry Sea Level products for oceanographic applications, climate forecasting centers, geophysic and biology communities... These products consist in directly usable and easy to manipulate Level 3 (along-track cross-calibrated SLA) and Level 4 products (multiple sensors merged as maps or time series) and are available in global and regional version (Mediterranean Sea, Arctic, European Shelves …).The quality of the products is today limited by the altimeter technology "Low Resolution Mode" (LRM), and the lack of available observations. The launch of 2 new satellites in 2016, Jason-3 and Sentinel-3A, opens new perspectives. Using the global Synthetic Aperture Radar mode (SARM) coverage of S3A and optimizing the LRM altimeter processing (retracking, editing, ...) will allow us to fully exploit the fine-scale content of the altimetric missions. Thanks to this increase of real time altimetry observations we will also be able to improve Level-4 products by combining these new Level-3 products and new mapping methodology, such as dynamic interpolation. Finally these improvements will benefit to downstream products : geostrophic currents, Lagrangian products, eddy atlas… Overcoming all these challenges will provide major upgrades of Sea Level products to better fulfill user needs.

  7. New approach to optimize operational conditions for the biological treatment of a high-strength thiocyanate and ammonium waste: pH as key factor.

    Science.gov (United States)

    Lay-Son, Meiling; Drakides, Christian

    2008-02-01

    Biological treatment of coke and steel-processing wastewaters has to satisfy both industrial economic needs and environmental protection regulations. Nevertheless, as some of the pollutants contained in these waters or produced during the treatment are highly toxic, an effective and safe treatment has proved to be difficult to obtain. This paper reports the study of a biological method for the treatment of wastewaters containing free cyanide, thiocyanate and ammonium (NH4). Laboratory-scale activated-sludge reactors were fed with a synthetic solution reproducing a steel-processing industrial wastewater and inoculated with the same industrial bacterial seeding used on-site (Ecosynergie Inc.). The results demonstrated that free cyanide and thiocyanate were efficiently degraded. Nevertheless, thiocyanate degradation and nitrification processes were actually inhibited by the free ammonia form (NH3) in place of the ionized NH4 form (NH4+) currently dosed and often unproperly named "ammonia" [IUPAC, 1997. In: McNaught, A.D., Wilkinson, A. (compilers). Compendium of Chemical Terminology. Royal Society of Chemistry, Cambridge, UK]. Optimum degradation rates were obtained for very narrow ranges of ammonia nitrogen (NH3-N) concentrations. This result can be explained by the role of pH, which mainly controls the NH3/NH4 equilibrium. Pollutants and NH3 concentrations influenced degradation rates of main pollutants. This influence was determined and expressed through elementary equations. Although the Michaelis-Menten equation could have been used to describe thiocyanate degradation, a Haldane-inhibition model was used to satisfactorily describe cyanide degradation. On the other hand, a slightly modified Haldane model was applied to describe both NH4 oxidation using NH3-N as substrate and thiocyanate degradation using NH3-N as inhibitor. These findings emphasize the role of pH on degradation rates and allow one to optimize operational conditions in the biological treatment of

  8. Experimental observations of detonation in ammonium-nitrate-fuel-oil (ANFO) surrounded by a high-sound speed, shockless, aluminum confiner

    Energy Technology Data Exchange (ETDEWEB)

    Jackson, Scott I [Los Alamos National Laboratory; Klyanda, Charles B [Los Alamos National Laboratory; Short, Mark [Los Alamos National Laboratory

    2010-01-01

    Detonations in explosive mixtures of ammonium-nitrate-fuel-oil (ANFO) confined by aluminum allow for transport of detonation energy ahead of the detonation front due to the aluminum sound speed exceeding the detonation velocity. The net effect of this energy transport on the detonation is unclear. It could enhance the detonation by precompressing the explosive near the wall. Alternatively, it could desensitize the explosive by crushing porosity required for shock initiation or destroying confinement ahead of the detonation. As these phenomena are not well understood, most numerical explosive models are unable to account for them. But with slowly detonating, non-ideal high explosive (NIHE) systems becoming increasing prevalent, proper understanding and prediction of the performance of these metal-confined NIHE systems is desirable. Experiments are discussed that measured the effect of this ANFO detonation energy transported upstream of the front by an aluminum confining tube. Detonation velocity, detonation front curvature, and aluminum response are recorded as a function of confiner wall thickness and length. Front curvature profiles display detonation acceleration near the confining surface, which is attributed to energy transported upstream modifying the flow. Average detonation velocities were seen to increase with increasing confiner thickness due to the additional inertial confinement of the reaction zone flow. Significant radial sidewall tube motion was observed immediately ahead of the detonation. Axial motion was also detected which interfered with the front curvature measurements in some cases. It was concluded that the confiner was able to transport energy ahead of the detonation and that this transport has a definite effect on the detonation.

  9. Tracking at High Level Trigger in CMS

    CERN Document Server

    Tosi, Mia

    2014-01-01

    A reduction of several orders of magnitude of the event rate is needed to reach values compatible with detector readout, offline storage and analysis capability. The CMS experiment has been designed with a two-level trigger system: the Level-1 Trigger (L1T), implemented on custom-designed electronics, and the High Level Trigger (HLT), a streamlined version of the CMS offline reconstruction software running on a computer farm. A software trigger system requires a trade-off between the complexity of the algorithms, the sustainable output rate, and the selection efficiency. With the computing power available during the 2012 data taking the maximum reconstruction time at HLT was about 200 ms per event, at the nominal L1T rate of 100 kHz. Track reconstruction algorithms are widely used in the HLT, for the reconstruction of the physics objects as well as in the identification of b-jets and lepton iso...

  10. Ammonium acetate enhances solvent production by Clostridium acetobutylicum EA 2018 using cassava as a fermentation medium.

    Science.gov (United States)

    Gu, Yang; Hu, Shiyuan; Chen, Jun; Shao, Lijun; He, Huiqi; Yang, Yunliu; Yang, Sheng; Jiang, Weihong

    2009-09-01

    Cassava, due to its high starch content and low cost, is a promising candidate substrate for large-scale fermentation processes aimed at producing the solvents acetone, butanol and ethanol (ABE). However, the solvent yield from the fermentation of cassava reaches only 60% of that achieved by fermenting corn. We have found that the addition of ammonium acetate (CH(3)COONH(4)) to the cassava medium significantly promotes solvent production from cassava fermented by Clostridium acetobutylicum EA 2018, a mutant with a high butanol ratio. When cassava medium was supplemented with 30 mM ammonium acetate, the acetone, butanol and total solvent production reached 5.0, 13.0 and 19.4 g/l, respectively, after 48 h of fermentation. This level of solvent production is comparable to that obtained from corn medium. Both ammonium (NH(4) (+)) and acetate (CH(3)COO(-)) were required for increased solvent synthesis. We also demonstrated substantially increased acetic and butyric acid accumulation during the acidogenesis phase as well as greater acid re-assimilation during the solventogenesis period in ammonium acetate-supplemented cassava medium. Reverse transcription-polymerase chain reaction analysis indicated that the transcription of several genes encoding enzymes related to acidogenesis and solventogenesis in C. acetobutylicum EA 2018 were enhanced by the addition of ammonium acetate to the cassava medium.

  11. High-Level Waste Melter Study Report

    Energy Technology Data Exchange (ETDEWEB)

    Perez, Joseph M.; Bickford, Dennis F.; Day, Delbert E.; Kim, Dong-Sang; Lambert, Steven L.; Marra, Sharon L.; Peeler, David K.; Strachan, Denis M.; Triplett, Mark B.; Vienna, John D.; Wittman, Richard S.

    2001-07-13

    At the Hanford Site in Richland, Washington, the path to site cleanup involves vitrification of the majority of the wastes that currently reside in large underground tanks. A Joule-heated glass melter is the equipment of choice for vitrifying the high-level fraction of these wastes. Even though this technology has general national and international acceptance, opportunities may exist to improve or change the technology to reduce the enormous cost of accomplishing the mission of site cleanup. Consequently, the U.S. Department of Energy requested the staff of the Tanks Focus Area to review immobilization technologies, waste forms, and modifications to requirements for solidification of the high-level waste fraction at Hanford to determine what aspects could affect cost reductions with reasonable long-term risk. The results of this study are summarized in this report.

  12. Service-oriented high level architecture

    CERN Document Server

    Wang, Wenguang; Li, Qun; Wang, Weiping; Liu, Xichun

    2009-01-01

    Service-oriented High Level Architecture (SOHLA) refers to the high level architecture (HLA) enabled by Service-Oriented Architecture (SOA) and Web Services etc. techniques which supports distributed interoperating services. The detailed comparisons between HLA and SOA are made to illustrate the importance of their combination. Then several key enhancements and changes of HLA Evolved Web Service API are introduced in comparison with native APIs, such as Federation Development and Execution Process, communication mechanisms, data encoding, session handling, testing environment and performance analysis. Some approaches are summarized including Web-Enabling HLA at the communication layer, HLA interface specification layer, federate interface layer and application layer. Finally the problems of current research are discussed, and the future directions are pointed out.

  13. High-Level Waste Melter Study Report

    Energy Technology Data Exchange (ETDEWEB)

    Perez Jr, Joseph M; Bickford, Dennis F; Day, Delbert E; Kim, Dong-Sang; Lambert, Steven L; Marra, Sharon L; Peeler, David K; Strachan, Denis M; Triplett, Mark B; Vienna, John D; Wittman, Richard S

    2001-07-13

    At the Hanford Site in Richland, Washington, the path to site cleanup involves vitrification of the majority of the wastes that currently reside in large underground tanks. A Joule-heated glass melter is the equipment of choice for vitrifying the high-level fraction of these wastes. Even though this technology has general national and international acceptance, opportunities may exist to improve or change the technology to reduce the enormous cost of accomplishing the mission of site cleanup. Consequently, the U.S. Department of Energy requested the staff of the Tanks Focus Area to review immobilization technologies, waste forms, and modifications to requirements for solidification of the high-level waste fraction at Hanford to determine what aspects could affect cost reductions with reasonable long-term risk. The results of this study are summarized in this report.

  14. High-level radioactive wastes. Supplement 1

    Energy Technology Data Exchange (ETDEWEB)

    McLaren, L.H. (ed.)

    1984-09-01

    This bibliography contains information on high-level radioactive wastes included in the Department of Energy's Energy Data Base from August 1982 through December 1983. These citations are to research reports, journal articles, books, patents, theses, and conference papers from worldwide sources. Five indexes, each preceded by a brief description, are provided: Corporate Author, Personal Author, Subject, Contract Number, and Report Number. 1452 citations.

  15. Commissioning of the CMS High Level Trigger

    CERN Document Server

    Agostino, Lorenzo; Beccati, Barbara; Behrens, Ulf; Berryhil, Jeffrey; Biery, Kurt; Bose, Tulika; Brett, Angela; Branson, James; Cano, Eric; Cheung, Harry; Ciganek, Marek; Cittolin, Sergio; Coarasa, Jose Antonio; Dahmes, Bryan; Deldicque, Christian; Dusinberre, Elizabeth; Erhan, Samim; Gigi, Dominique; Glege, Frank; Gomez-Reino, Robert; Gutleber, Johannes; Hatton, Derek; Laurens, Jean-Francois; Loizides, Constantin; Ma, Frank; Meijers, Frans; Meschi, Emilio; Meyer, Andreas; Mommsen, Remigius K; Moser, Roland; O'Dell, Vivian; Oh, Alexander; Orsini, Luciano; Patras, Vaios; Paus, Christoph; Petrucci, Andrea; Pieri, Marco; Racz, Attila; Sakulin, Hannes; Sani, Matteo; Schieferdeckerd, Philipp; Schwick, Christoph; Serrano Margaleff, Josep Francesc; Shpakov, Dennis; Simon, Sean; Sumorok, Konstanty; Sungho Yoon, Andre; Wittich, Peter; Zanetti, Marco

    2009-01-01

    The CMS experiment will collect data from the proton-proton collisions delivered by the Large Hadron Collider (LHC) at a centre-of-mass energy up to 14 TeV. The CMS trigger system is designed to cope with unprecedented luminosities and LHC bunch-crossing rates up to 40 MHz. The unique CMS trigger architecture only employs two trigger levels. The Level-1 trigger is implemented using custom electronics, while the High Level Trigger (HLT) is based on software algorithms running on a large cluster of commercial processors, the Event Filter Farm. We present the major functionalities of the CMS High Level Trigger system as of the starting of LHC beams operations in September 2008. The validation of the HLT system in the online environment with Monte Carlo simulated data and its commissioning during cosmic rays data taking campaigns are discussed in detail. We conclude with the description of the HLT operations with the first circulating LHC beams before the incident occurred the 19th September 2008.

  16. Commissioning of the CMS High Level Trigger

    Energy Technology Data Exchange (ETDEWEB)

    Agostino, Lorenzo; et al.

    2009-08-01

    The CMS experiment will collect data from the proton-proton collisions delivered by the Large Hadron Collider (LHC) at a centre-of-mass energy up to 14 TeV. The CMS trigger system is designed to cope with unprecedented luminosities and LHC bunch-crossing rates up to 40 MHz. The unique CMS trigger architecture only employs two trigger levels. The Level-1 trigger is implemented using custom electronics, while the High Level Trigger (HLT) is based on software algorithms running on a large cluster of commercial processors, the Event Filter Farm. We present the major functionalities of the CMS High Level Trigger system as of the starting of LHC beams operations in September 2008. The validation of the HLT system in the online environment with Monte Carlo simulated data and its commissioning during cosmic rays data taking campaigns are discussed in detail. We conclude with the description of the HLT operations with the first circulating LHC beams before the incident occurred the 19th September 2008.

  17. Commissioning of the CMS High Level Trigger

    Energy Technology Data Exchange (ETDEWEB)

    Agostino, Lorenzo; et al.

    2009-08-01

    The CMS experiment will collect data from the proton-proton collisions delivered by the Large Hadron Collider (LHC) at a centre-of-mass energy up to 14 TeV. The CMS trigger system is designed to cope with unprecedented luminosities and LHC bunch-crossing rates up to 40 MHz. The unique CMS trigger architecture only employs two trigger levels. The Level-1 trigger is implemented using custom electronics, while the High Level Trigger (HLT) is based on software algorithms running on a large cluster of commercial processors, the Event Filter Farm. We present the major functionalities of the CMS High Level Trigger system as of the starting of LHC beams operations in September 2008. The validation of the HLT system in the online environment with Monte Carlo simulated data and its commissioning during cosmic rays data taking campaigns are discussed in detail. We conclude with the description of the HLT operations with the first circulating LHC beams before the incident occurred the 19th September 2008.

  18. Both Free Indole-3-Acetic Acid and Photosynthetic Performance are Important Players in the Response of Medicago truncatula to Urea and Ammonium Nutrition Under Axenic Conditions

    Science.gov (United States)

    Esteban, Raquel; Royo, Beatriz; Urarte, Estibaliz; Zamarreño, Ángel M.; Garcia-Mina, José M.; Moran, Jose F.

    2016-01-01

    We aimed to identify the early stress response and plant performance of Medicago truncatula growing in axenic medium with ammonium or urea as the sole source of nitrogen, with respect to nitrate-based nutrition. Biomass measurements, auxin content analyses, root system architecture (RSA) response analyses, and physiological parameters were determined. Both ammonium and ureic nutrition severely affected the RSA, resulting in changes in the main elongation rate, lateral root development, and insert position from the root base. The auxin content decreased in both urea- and ammonium-treated roots; however, only the ammonium-treated plants were affected at the shoot level. The analysis of chlorophyll a fluorescence transients showed that ammonium affected photosystem II, but urea did not impair photosynthetic activity. Superoxide dismutase isoenzymes in the plastids were moderately affected by urea and ammonium in the roots. Overall, our results showed that low N doses from different sources had no remarkable effects on M. truncatula, with the exception of the differential phenotypic root response. High doses of both ammonium and urea caused great changes in plant length, auxin contents and physiological measurements. Interesting correlations were found between the shoot auxin pool and both plant length and the “performance index” parameter, which is obtained from measurements of the kinetics of chlorophyll a fluorescence. Taken together, these data demonstrate that both the indole-3-acetic acid pool and performance index are important components of the response of M. truncatula under ammonium or urea as the sole N source. PMID:26909089

  19. Both free indole-3-acetic acid and the photosynthetic performance are important players in the response of Medicago truncatula to urea and ammonium nutrition under axenic conditions

    Directory of Open Access Journals (Sweden)

    RAQUEL eEsteban

    2016-02-01

    Full Text Available We aimed to identify the early stress response and plant performance of Medicago truncatula growing in axenic medium with ammonium or urea as the sole source of nitrogen with respect to nitrate based nutrition through biomass measurements, auxin contents analyses, root system architecture response analyses, and physiological determinations. Both ammonium and ureic nutrition severely affected the root system architecture, resulting in changes in the main elongation rate, lateral root development and insert position from the base. The auxin content decreased in both urea- and ammonium- treated roots; however, only the ammonium- treated plants were affected at the shoot level. The analysis of chlorophyll a fluorescence transients showed that ammonium affected photosystem II, but urea did not impair photosynthetic activity. Superoxide dismutase isoenzymes in the plastids were moderately affected by urea and ammonium in the roots. Overall, our results showed that low N doses from different sources had no remarkable effects on M. truncatula, with the exception of the differential phenotypic root response. High dose of both ammonium and urea caused great changes at plant length, auxin content and physiological determinations. The interesting correlations found between the shoot auxin pool, the plant length, and the parameter performance index, obtained from the chlorophyll a fluorescence rise kinetics measurements, indicated that both IAA pool and performance index are an important part of the response of M. truncatula under ammonium or urea as a sole N source.

  20. The ALICE Dimuon Spectrometer High Level Trigger

    CERN Document Server

    Becker, B; Cicalo, Corrado; Das, Indranil; de Vaux, Gareth; Fearick, Roger; Lindenstruth, Volker; Marras, Davide; Sanyal, Abhijit; Siddhanta, Sabyasachi; Staley, Florent; Steinbeck, Timm; Szostak, Artur; Usai, Gianluca; Vilakazi, Zeblon

    2009-01-01

    The ALICE Dimuon Spectrometer High Level Trigger (dHLT) is an on-line processing stage whose primary function is to select interesting events that contain distinct physics signals from heavy resonance decays such as J/psi and Gamma particles, amidst unwanted background events. It forms part of the High Level Trigger of the ALICE experiment, whose goal is to reduce the large data rate of about 25 GB/s from the ALICE detectors by an order of magnitude, without loosing interesting physics events. The dHLT has been implemented as a software trigger within a high performance and fault tolerant data transportation framework, which is run on a large cluster of commodity compute nodes. To reach the required processing speeds, the system is built as a concurrent system with a hierarchy of processing steps. The main algorithms perform partial event reconstruction, starting with hit reconstruction on the level of the raw data received from the spectrometer. Then a tracking algorithm finds track candidates from the recon...

  1. Performance of the CMS High Level Trigger

    CERN Document Server

    Perrotta, Andrea

    2015-01-01

    The CMS experiment has been designed with a 2-level trigger system. The first level is implemented using custom-designed electronics. The second level is the so-called High Level Trigger (HLT), a streamlined version of the CMS offline reconstruction software running on a computer farm. For Run II of the Large Hadron Collider, the increases in center-of-mass energy and luminosity will raise the event rate to a level challenging for the HLT algorithms. The increase in the number of interactions per bunch crossing, on average 25 in 2012, and expected to be around 40 in Run II, will be an additional complication. We present here the expected performance of the main triggers that will be used during the 2015 data taking campaign, paying particular attention to the new approaches that have been developed to cope with the challenges of the new run. This includes improvements in HLT electron and photon reconstruction as well as better performing muon triggers. We will also present the performance of the improved trac...

  2. Intergenerational ethics of high level radioactive waste

    Energy Technology Data Exchange (ETDEWEB)

    Takeda, Kunihiko [Nagoya Univ., Graduate School of Engineering, Nagoya, Aichi (Japan); Nasu, Akiko; Maruyama, Yoshihiro [Shibaura Inst. of Tech., Tokyo (Japan)

    2003-03-01

    The validity of intergenerational ethics on the geological disposal of high level radioactive waste originating from nuclear power plants was studied. The result of the study on geological disposal technology showed that the current method of disposal can be judged to be scientifically reliable for several hundred years and the radioactivity level will be less than one tenth of the tolerable amount after 1,000 years or more. This implies that the consideration of intergenerational ethics of geological disposal is meaningless. Ethics developed in western society states that the consent of people in the future is necessary if the disposal has influence on them. Moreover, the ethics depends on generally accepted ideas in western society and preconceptions based on racism and sexism. The irrationality becomes clearer by comparing the dangers of the exhaustion of natural resources and pollution from harmful substances in a recycling society. (author)

  3. Proton Affinity Calculations with High Level Methods.

    Science.gov (United States)

    Kolboe, Stein

    2014-08-12

    Proton affinities, stretching from small reference compounds, up to the methylbenzenes and naphthalene and anthracene, have been calculated with high accuracy computational methods, viz. W1BD, G4, G3B3, CBS-QB3, and M06-2X. Computed and the currently accepted reference proton affinities are generally in excellent accord, but there are deviations. The literature value for propene appears to be 6-7 kJ/mol too high. Reported proton affinities for the methylbenzenes seem 4-5 kJ/mol too high. G4 and G3 computations generally give results in good accord with the high level W1BD. Proton affinity values computed with the CBS-QB3 scheme are too low, and the error increases with increasing molecule size, reaching nearly 10 kJ/mol for the xylenes. The functional M06-2X fails markedly for some of the small reference compounds, in particular, for CO and ketene, but calculates methylbenzene proton affinities with high accuracy.

  4. The high-level trigger of ALICE

    Energy Technology Data Exchange (ETDEWEB)

    Tilsner, H.; Lindenstruth, V.; Steinbeck, T. [Kirchhoff Institute for Physics, University of Heidelberg (Germany); Alt, T.; Aurbakken, K.; Grastveit, G.; Nystrand, J.; Roehrich, D.; Ullaland, K.; Vestbo, A. [Department of Physics, University of Bergen (Norway); Helstrup, H. [Bergen College (Norway); Loizides, C. [Institute of Nuclear Physics, University of Frankfurt (Germany); Skaali, B.; Vik, T. [Department of Physics, University of Oslo (Norway)

    2004-07-01

    One of the main tracking detectors of the forthcoming ALICE Experiment at the LHC is a cylindrical Time Projection Chamber (TPC) with an expected data volume of about 75 MByte per event. This data volume, in combination with the presumed maximum bandwidth of 1.2 GByte/s to the mass storage system, would limit the maximum event rate to 20 Hz. In order to achieve higher event rates, online data processing has to be applied. This implies either the detection and read-out of only those events which contain interesting physical signatures or an efficient compression of the data by modeling techniques. In order to cope with the anticipated data rate, massive parallel computing power is required. It will be provided in form of a clustered farm of SMP-nodes, based on off-the-shelf PCs, which are connected with a high bandwidth low overhead network. This High-Level Trigger (HLT) will be able to process a data rate of 25 GByte/s online. The front-end electronics of the individual sub-detectors is connected to the HLT via an optical link and a custom PCI card which is mounted in the clustered PCs. The PCI card is equipped with an FPGA necessary for the implementation of the PCI-bus protocol. Therefore, this FPGA can also be used to assist the host processor with first-level processing. The first-level processing done on the FPGA includes conventional cluster-finding for low multiplicity events and local track finding based on the Hough Transformation of the raw data for high multiplicity events. (orig.)

  5. The high-level trigger of ALICE

    Science.gov (United States)

    Tilsner, H.; Alt, T.; Aurbakken, K.; Grastveit, G.; Helstrup, H.; Lindenstruth, V.; Loizides, C.; Nystrand, J.; Roehrich, D.; Skaali, B.; Steinbeck, T.; Ullaland, K.; Vestbo, A.; Vik, T.

    One of the main tracking detectors of the forthcoming ALICE Experiment at the LHC is a cylindrical Time Projection Chamber (TPC) with an expected data volume of about 75 MByte per event. This data volume, in combination with the presumed maximum bandwidth of 1.2 GByte/s to the mass storage system, would limit the maximum event rate to 20 Hz. In order to achieve higher event rates, online data processing has to be applied. This implies either the detection and read-out of only those events which contain interesting physical signatures or an efficient compression of the data by modeling techniques. In order to cope with the anticipated data rate, massive parallel computing power is required. It will be provided in form of a clustered farm of SMP-nodes, based on off-the-shelf PCs, which are connected with a high bandwidth low overhead network. This High-Level Trigger (HLT) will be able to process a data rate of 25 GByte/s online. The front-end electronics of the individual sub-detectors is connected to the HLT via an optical link and a custom PCI card which is mounted in the clustered PCs. The PCI card is equipped with an FPGA necessary for the implementation of the PCI-bus protocol. Therefore, this FPGA can also be used to assist the host processor with first-level processing. The first-level processing done on the FPGA includes conventional cluster-finding for low multiplicity events and local track finding based on the Hough Transformation of the raw data for high multiplicity events. PACS: 07.05.-t Computers in experimental physics - 07.05.Hd Data acquisition: hardware and software - 29.85.+c Computer data analysis

  6. The ARES High-level Intermediate Representation

    Energy Technology Data Exchange (ETDEWEB)

    Moss, Nicholas David [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-03-03

    The LLVM intermediate representation (IR) lacks semantic constructs for depicting common high-performance operations such as parallel and concurrent execution, communication and synchronization. Currently, representing such semantics in LLVM requires either extending the intermediate form (a signi cant undertaking) or the use of ad hoc indirect means such as encoding them as intrinsics and/or the use of metadata constructs. In this paper we discuss a work in progress to explore the design and implementation of a new compilation stage and associated high-level intermediate form that is placed between the abstract syntax tree and when it is lowered to LLVM's IR. This highlevel representation is a superset of LLVM IR and supports the direct representation of these common parallel computing constructs along with the infrastructure for supporting analysis and transformation passes on this representation.

  7. Single-particle analysis reveals shutoff control of the Arabidopsis ammonium transporter AMT1;3 by clustering and internalization.

    Science.gov (United States)

    Wang, Qinli; Zhao, Yuanyuan; Luo, Wangxi; Li, Ruili; He, Qihua; Fang, Xiaohong; Michele, Roberto De; Ast, Cindy; von Wirén, Nicolaus; Lin, Jinxing

    2013-08-01

    Ammonium is a preferred source of nitrogen for plants but is toxic at high levels. Plant ammonium transporters (AMTs) play an essential role in NH4(+) uptake, but the mechanism by which AMTs are regulated remains unclear. To study how AMTs are regulated in the presence of ammonium, we used variable-angle total internal reflection fluorescence microscopy and fluorescence cross-correlation spectroscopy for single-particle fluorescence imaging of EGFP-tagged AMT1;3 on the plasma membrane of Arabidopsis root cells at various ammonium levels. We demonstrated that AMT1;3-EGFP dynamically appeared and disappeared on the plasma membrane as moving fluorescent spots in low oligomeric states under N-deprived and N-sufficient conditions. Under external high-ammonium stress, however, AMT1;3-EGFPs were found to amass into clusters, which were then internalized into the cytoplasm. A similar phenomenon also occurred in the glutamine synthetase mutant gln1;2 background. Single-particle analysis of AMT1;3-EGFPs in the clathrin heavy chain 2 mutant (chc2 mutant) and Flotllin1 artificial microRNA (Flot1 amiRNA) backgrounds, together with chemical inhibitor treatments, demonstrated that the endocytosis of AMT1;3 clusters induced by high-ammonium stress could occur mainly through clathrin-mediated endocytic pathways, but the contribution of microdomain-associated endocytic pathway cannot be excluded in the internalization. Our results revealed that the clustering and endocytosis of AMT1;3 provides an effective mechanism by which plant cells can avoid accumulation of toxic levels of ammonium by eliminating active AMT1;3 from the plasma membrane.

  8. Ammonium diphosphitoindate(III

    Directory of Open Access Journals (Sweden)

    Farida Hamchaoui

    2013-04-01

    Full Text Available The crystal structure of the title compound, NH4[In(HPO32], is built up from InIII cations (site symmetry 3m. adopting an octahedral environment and two different phosphite anions (each with site symmetry 3m. exhibiting a triangular–pyramidal geometry. Each InO6 octahedron shares its six apices with hydrogen phosphite groups. Reciprocally, each HPO3 group shares all its O atoms with three different metal cations, leading to [In(HPO32]− layers which propagate in the ab plane. The ammonium cation likewise has site symmetry 3m.. In the structure, the cations are located between the [In(HPO32]− layers of the host framework. The sheets are held together by hydrogen bonds formed between the NH4+ cations and the O atoms of the framework.

  9. Tracking at High Level Trigger in CMS

    CERN Document Server

    Tosi, Mia

    2016-01-01

    The trigger systems of the LHC detectors play a crucial role in determining the physics capabili- ties of the experiments. A reduction of several orders of magnitude of the event rate is needed to reach values compatible with detector readout, offline storage and analysis capability. The CMS experiment has been designed with a two-level trigger system: the Level-1 Trigger (L1T), implemented on custom-designed electronics, and the High Level Trigger (HLT), a stream- lined version of the CMS offline reconstruction software running on a computer farm. A software trigger system requires a trade-off between the complexity of the algorithms, the sustainable out- put rate, and the selection efficiency. With the computing power available during the 2012 data taking the maximum reconstruction time at HLT was about 200 ms per event, at the nominal L1T rate of 100 kHz. Track reconstruction algorithms are widely used in the HLT, for the reconstruction of the physics objects as well as in the identification of b-jets and ...

  10. Multi-species measurements of nitrogen isotopic composition reveal the spatial constraints and biological drivers of ammonium attenuation across a highly contaminated groundwater system.

    Science.gov (United States)

    Wells, Naomi S; Hakoun, Vivien; Brouyère, Serge; Knöller, Kay

    2016-07-01

    Groundwater under industrial sites is characterised by heterogeneous chemical mixtures, making it difficult to assess the fate and transport of individual contaminants. Quantifying the in-situ biological removal (attenuation) of nitrogen (N) is particularly difficult due to its reactivity and ubiquity. Here a multi-isotope approach is developed to distinguish N sources and sinks within groundwater affected by complex industrial pollution. Samples were collected from 70 wells across the two aquifers underlying a historic industrial area in Belgium. Below the industrial site the groundwater contained up to 1000 mg N l(-1) ammonium (NH4(+)) and 300 mg N l(-1) nitrate (NO3(-)), while downgradient concentrations decreased to ∼1 mg l(-1) DIN ([DIN] = [NH4(+)N] + [NO3(-)N] + [NO2(-)N]). Mean δ(15)N-DIN increased from ∼2‰ to +20‰ over this flow path, broadly confirming that biological N attenuation drove the measured concentration decrease. Multi-variate analysis of water chemistry identified two distinct NH4(+) sources (δ(15)NNH4(+) from -14‰ and +5‰) within the contaminated zone of both aquifers. Nitrate dual isotopes co-varied (δ(15)N: -3‰ - +60‰; δ(18)O: 0‰ - +50‰) within the range expected for coupled nitrification and denitrification of the identified sources. The fact that δ(15)NNO2(-) values were 50‰-20‰ less than δ(15)NNH4(+) values in the majority of wells confirmed that nitrification controlled N turnover across the site. However, the fact that δ(15)NNO2(-) was greater than δ(15)NNH4(+) in wells with the highest [NH4(+)] shows that an autotrophic NO2(-) reduction pathway (anaerobic NH4(+) oxidation or nitrifier-denitrification) drove N attenuation closest to the contaminant plume. This direct empirical evidence that both autotrophic and heterotrophic biogeochemical processes drive N attenuation in contaminated aquifers demonstrates the power of multiple N isotopes to untangle N cycling in highly complex

  11. Waterproofing Materials for Ammonium Nitrate

    Directory of Open Access Journals (Sweden)

    R.S. Damse

    2004-10-01

    Full Text Available This study explores the possibility of overcoming the problem of hygroscopicity of ammonium nitrate by coating the particles with selected waterproofing materials. Gravimetric analysis ofthe samples of ammonium nitrate coated with eight different waterproofing materials, vis-a-vis, uncoated ammonium nitrate, were conducted at different relative humidity and exposuretime. The results indicate that mineral jelly is the promising waterproofing material for ammonium nitrate among the materials tested, viz, calcium stearate, dioctyl phthalate, kaoline, diethylphthalate, dinitrotoluene, shelac varnish, and beeswax. Attempts were made to confirm the waterproofing ability of mineral jelly to ammonium nitrate using differential thermal analysisand x-ray diffraction patterns as an experimental tool. Suitability of mineral jelly as an additive for the gun propellant was also assessed on the basis of theoretical calculations using THERMprogram.

  12. Reliability-Centric High-Level Synthesis

    CERN Document Server

    Tosun, S; Arvas, E; Kandemir, M; Xie, Yuan

    2011-01-01

    Importance of addressing soft errors in both safety critical applications and commercial consumer products is increasing, mainly due to ever shrinking geometries, higher-density circuits, and employment of power-saving techniques such as voltage scaling and component shut-down. As a result, it is becoming necessary to treat reliability as a first-class citizen in system design. In particular, reliability decisions taken early in system design can have significant benefits in terms of design quality. Motivated by this observation, this paper presents a reliability-centric high-level synthesis approach that addresses the soft error problem. The proposed approach tries to maximize reliability of the design while observing the bounds on area and performance, and makes use of our reliability characterization of hardware components such as adders and multipliers. We implemented the proposed approach, performed experiments with several designs, and compared the results with those obtained by a prior proposal.

  13. Ammonium Perchlorate and Ammonium Perchlorate- Hydroxyl Terminated Polybutadiene Simulated Combustion

    Directory of Open Access Journals (Sweden)

    Rene Francisco Boschi Gonçalves

    2012-03-01

    Full Text Available The combustion simulation of ammonium perchlorate was carried out with the software Chemkin, in two steps: the burning behavior of pure ammonium perchlorate and the one of formulated ammonium perchlorate with hydroxyl terminated polybutadiene binder. In both cases, the room pressure varied in order to verify its influence in the system. The burning environment conditions were diverse. During the combustion process, the data obtained from the kinetic chemistry simulation software were compiled. The flame structure can be described by the molar fraction of the burning products and the temperature evolution from the surface of the material.

  14. Impact of ammonium nitrate and sodium nitrate on tadpoles of Alytes obstetricans.

    Science.gov (United States)

    Garriga, Núria; Montori, A; Llorente, G A

    2017-07-01

    The presence of pesticides, herbicides and fertilisers negatively affect aquatic communities in general, and particularly amphibians in their larval phase, even though sensitivity to pollutants is highly variable among species. The Llobregat Delta (Barcelona, Spain) has experienced a decline of amphibian populations, possibly related to the reduction in water quality due to the high levels of farming activity, but also to habitat loss and alteration. We studied the effects of increasing ammonium nitrate and sodium nitrate levels on the survival and growth rate of Alytes obstetricans tadpoles under experimental conditions. We exposed larvae to increasing concentrations of nitrate and ammonium for 14 days and then exposed them to water without pollutants for a further 14 days. Only the higher concentrations of ammonium (>33.75 mg/L) caused larval mortality. The growth rate of larvae was reduced at ≥22.5 mg/L NH4(+), although individuals recovered and even increased their growth rate once exposure to the pollutant ended. The effect of nitrate on growth rate was detected at ≥80 mg/L concentrations, and the growth rate reduction in tadpoles was even observed during the post-exposure phase. The concentrations of ammonium with adverse effects on larvae are within the range levels found in the study area, while the nitrate concentrations with some adverse effect are close to the upper range limit of current concentrations in the study area. Therefore, only the presence of ammonium in the study area is likely to be considered of concern for the population of this species, even though the presence of nitrate could cause some sublethal effects. These negative effects could have an impact on population dynamics, which in this species is highly sensitive to larval mortality due to its small clutch size and prolonged larval period compared to other anuran amphibians.

  15. The ATLAS High Level Trigger Steering

    CERN Document Server

    Berger, N; Eifert, T; Fischer, G; George, S; Haller, J; Höcker, A; Masik, J; Zur Nedden, M; Pérez-Réale, V; Risler, C; Schiavi, C; Stelzer, J; Wu, X; International Conference on Computing in High Energy and Nuclear Physics

    2008-01-01

    The High Level Trigger (HLT) of the ATLAS experiment at the Large Hadron Collider receives events which pass the LVL1 trigger at ~75 kHz and has to reduce the rate to ~200 Hz while retaining the most interesting physics. It is a software trigger and performs the reduction in two stages: the LVL2 trigger and the Event Filter (EF). At the heart of the HLT is the Steering software. To minimise processing time and data transfers it implements the novel event selection strategies of seeded, step-wise reconstruction and early rejection. The HLT is seeded by regions of interest identified at LVL1. These and the static configuration determine which algorithms are run to reconstruct event data and test the validity of trigger signatures. The decision to reject the event or continue is based on the valid signatures, taking into account pre-scale and pass-through. After the EF, event classification tags are assigned for streaming purposes. Several powerful new features for commissioning and operation have been added: co...

  16. Physical exertion may cause high troponin levels.

    Science.gov (United States)

    Agewall, Stefan; Tjora, Solve

    2011-11-15

    It is important to measure troponin levels when acute myocardial infarct is suspected. Many other factors that affect the heart can cause an increase in troponin levels, for example extreme physical exertion. Recent studies have shown that more normal physical activity can also lead to increase in troponin levels in healthy individuals.

  17. Influence of Alkyl Trimethyl Ammonium Bromides on Hydrothermal Formation of α-CaSO4·0.5H2O Whiskers with High Aspect Ratios

    Directory of Open Access Journals (Sweden)

    Ruosong Chen

    2017-01-01

    Full Text Available In this paper, the influence of alkyl trimethyl ammonium bromides (CnH2n+1(CH33NBr, n = 10, 12, 14, 16, 18, abbreviated as ATAB on the formation of alpha calcium sulfate hemihydrate (α-CaSO4·0.5H2O whiskers under a hydrothermal condition (135 °C, 3.0 h was analyzed. Specifically, it focuses on cetyl trimethyl ammonium bromide (C16H33(CH33NBr, abbreviated as CTAB. The rising CTAB concentration from 0 to 9.2 × 10−4 mol·L−1 led to the increase of the average aspect ratio of α-CaSO4·0.5H2O whiskers from 80 to 430, since the selective adsorption of CTAB on the negatively-charged side facets of the whiskers inhibited the growth of the whiskers along the direction normal to the lateral facets. The further increase of CTAB concentration above the critical micelle concentration (abbreviated as CMC showed little effect on the morphology of α-CaSO4·0.5H2O whiskers, considering that CTAB tended to form micelles instead of being adsorbed on the whisker surfaces. Similar phenomena were observed in other ATABs (n = 10, 12, 14, 18.

  18. Development of an on-line source-tagged model for sulfate, nitrate and ammonium: A modeling study for highly polluted periods in Shanghai, China.

    Science.gov (United States)

    Wu, Jian-Bin; Wang, Zifa; Wang, Qian; Li, Jie; Xu, Jianming; Chen, HuanSheng; Ge, Baozhu; Zhou, Guangqiang; Chang, Luyu

    2017-02-01

    An on-line source-tagged model coupled with an air quality model (Nested Air Quality Prediction Model System, NAQPMS) was applied to estimate source contributions of primary and secondary sulfate, nitrate and ammonium (SNA) during a representative winter period in Shanghai. This source-tagged model system could simultaneously track spatial and temporal sources of SNA, which were apportioned to their respective primary precursors in a simulation run. The results indicate that in the study period, local emissions in Shanghai accounted for over 20% of SNA contributions and that Jiangsu and Shandong were the two major non-local sources. In particular, non-local emissions had higher contributions during recorded pollution periods. This suggests that the transportation of pollutants plays a key role in air pollution in Shanghai. The temporal contributions show that the emissions from the "current day" (emission contribution from the current day during which the model was simulating) contributed 60%-70% of the sulfate and ammonium concentrations but only 10%-20% of the nitrate concentration, while the previous days' contributions increased during the recorded pollution periods. Emissions that were released within three days contributed over 85% averagely for SNA in January 2013. To evaluate the source-tagged model system, the results were compared by sensitivity analysis (emission perturbation of -30%) and backward trajectory analysis. The consistency of the comparison results indicated that the source-tagged model system can track sources of SNA with reasonable accuracy.

  19. Headspace Analysis of Ammonium Nitrate

    Science.gov (United States)

    2017-01-25

    Naval Research Laboratory Washington, DC 20375-5320 NRL/MR/6110--17-9709 Headspace Analysis of Ammonium Nitrate January 25, 2017 Approved for public...TELEPHONE NUMBER (include area code) b. ABSTRACT c. THIS PAGE 18. NUMBER OF PAGES 17. LIMITATION OF ABSTRACT Headspace Analysis of Ammonium Nitrate G...isobutane reagent ion from analysis of ammonia desorbed from packed tungsten oxide sampling tube .................. 18 E-1 Executive Summary The

  20. Improved method for the determination of trace quaternary ammonium salt by high performance liquid chromatography%高效液相色谱法测定微量季铵盐的改进方法

    Institute of Scientific and Technical Information of China (English)

    卢姝; 纪然

    2011-01-01

    利用季铵盐与间硝基酚反应生成溶于有机溶剂的络合物,该络合物可以用紫外检测器进行定量分析,建立了一种高效液相色谱测定微量季铵盐的改进方法.该方法的线性范围为0.60~99.40 mg/L,最低检出限可达0.4mg/L,平均回收率为94.97%~104.02%,相对标准偏差为3.41%.该方法稳定、简便且灵敏度高,适于测定锅炉循环冷却水、工业废水及水处理药剂中季铵盐类阳离子表面活性剂的含量.%Quaternary ammonium salt and 3-nitrophenol have been used for preparing the complex compound which is soluble in organic solvent. The complex compound can be determined quantitatively with UV detector. An improved method for the determination of trace quaternary ammonium salt by the high performance liquid chromatography is established. The linear range of the method is 0.60-99.40 mg/L. Its lowest detection limit 0.4 mg/L, average recovery rate 94.97%-104.02% and relative standard deviation 3.41%. The method is rapid, convenient and highly sensitive. It is suitable for the determination of the content of cationic surfactant of quaternary ammonium salts in circulating cooling water, industrial wastewater and water treatment agents.

  1. ARE QUATERNARY AMMONIUM ANTIBACTERIALS SUITABLE FOR DENTAL COMPOSITE RESINS?

    Directory of Open Access Journals (Sweden)

    Iman MOHAMMADZADEH

    2016-06-01

    Full Text Available The objective of this study was to answer the following question: are quaternary ammonium antibacterials suitable for dental materials? Reviewing the literature on quaternary ammonium compounds evidenced that this type of compounds is soluble in water. Our own findings also showed that they are well soluble in water and that their application as dental composites requires to check their solubility level in water.

  2. 21 CFR 184.1133 - Ammonium alginate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ammonium alginate. 184.1133 Section 184.1133 Food... Specific Substances Affirmed as GRAS § 184.1133 Ammonium alginate. (a) Ammonium alginate (CAS Reg. No. 9005.... Ammonium alginate is prepared by the neutralization of purified alginic acid with appropriate pH...

  3. 21 CFR 184.1138 - Ammonium chloride.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ammonium chloride. 184.1138 Section 184.1138 Food... Specific Substances Affirmed as GRAS § 184.1138 Ammonium chloride. (a) Ammonium chloride (NH4Cl, CAS Reg. No. 12125-02-9) is produced by the reaction of sodium chloride and an ammonium salt in solution....

  4. Subcellular localization of ammonium transporters in Dictyostelium discoideum

    Directory of Open Access Journals (Sweden)

    Davis Carter T

    2008-12-01

    Full Text Available Abstract Background With the exception of vertebrates, most organisms have plasma membrane associated ammonium transporters which primarily serve to import a source of nitrogen for nutritional purposes. Dictyostelium discoideum has three ammonium transporters, Amts A, B and C. Our present work used fluorescent fusion proteins to determine the cellular localization of the Amts and tested the hypothesis that the transporters mediate removal of ammonia generated endogenously from the elevated protein catabolism common to many protists. Results Using RFP and YFP fusion constructs driven by the actin 15 promoter, we found that the three ammonium transporters were localized on the plasma membrane and on the membranes of subcellular organelles. AmtA and AmtB were localized on the membranes of endolysosomes and phagosomes, with AmtB further localized on the membranes of contractile vacuoles. AmtC also was localized on subcellular organelles when it was stabilized by coexpression with either the AmtA or AmtB fusion transporter. The three ammonium transporters exported ammonia linearly with regard to time during the first 18 hours of the developmental program as revealed by reduced export in the null strains. The fluorescently tagged transporters rescued export when expressed in the null strains, and thus they were functional transporters. Conclusion Unlike ammonium transporters in most organisms, which import NH3/NH4+ as a nitrogen source, those of Dictyostelium export ammonia/ammonium as a waste product from extensive catabolism of exogenously derived and endogenous proteins. Localization on proteolytic organelles and on the neutral contractile vacuole suggests that Dictyostelium ammonium transporters may have unique subcellular functions and play a role in the maintenance of intracellular ammonium distribution. A lack of correlation between the null strain phenotypes and ammonia excretion properties of the ammonium transporters suggests that it is not

  5. 由铵盐制备高纯氟化钡的工艺研究%Preparation technology of high purity barium fluoride from ammonium salt

    Institute of Scientific and Technical Information of China (English)

    许春晓; 刘晓红; 柯春兰; 章小明

    2011-01-01

    以氟化铵和氯化钡为原料,采用沉淀法制备了氟化钡.反应温度为25℃,反应时间为60min,氯化钡初始质量分数为10%,氟化铵与氯化钡物质的量比为2.2,m(洗水):m(滤饼)=10:1,可制备出纯度达99%以上的氟化钡.XRD谱图表明,样品氟化钡的所有衍射峰均与标准立方相氟化钡吻合,属立方晶系.该工艺流程简单,经济效益好.%Barium fluoride (BaF2 ) was prepared by precipitation method with ammonium fluoride and barium chloride as raw materials. BaF2 with purity of more than 99% can be prepared when reaction temperature is 25 ℃ ,reaction time is 60 rnin,initial mass fraction of barium chloride is 10% ,amount-of-substance ratio of ammonium fluoride to barium chloride is 2.2,and the mass ratio of washing water amount to filter cake amount = 10: 1. XRD pattern showed that all the diffraction peaks of barium fluoride sample were consistent with the standard cubic barium fluoride. Therefore it belongs to the cubic crystal system. The technology has short flow route and good economic benefits.

  6. High alcohol consumption causes high IgE levels but not high risk of allergic disease

    DEFF Research Database (Denmark)

    Lomholt, Frederikke K; Nielsen, Sune F; Nordestgaard, Børge G

    2016-01-01

    disease. Genetically, we explored potential causal relationships between alcohol consumption and IgE levels and allergic disease. RESULTS: The multivariable adjusted odds ratio for IgE levels greater than versus less than 150 kU/L and compared with subjects without allergic disease was 2.3 (95% CI, 2......BACKGROUND: High alcohol consumption is associated with high IgE levels in observational studies; however, whether high alcohol consumption leads to high IgE levels and allergic disease is unclear. OBJECTIVE: We tested the hypothesis that high alcohol consumption is associated with high IgE levels...... for the alcohol-metabolizing enzymes alcohol dehydrogenase 1B (ADH-1B; rs1229984) and alcohol dehydrogenase 1c (ADH-1C; rs698). Observationally, we investigated associations between IgE levels and allergic disease (allergic asthma, rhinitis, and eczema) and between alcohol consumption and IgE levels and allergic...

  7. Statistics of high-level scene context.

    Science.gov (United States)

    Greene, Michelle R

    2013-01-01

    CONTEXT IS CRITICAL FOR RECOGNIZING ENVIRONMENTS AND FOR SEARCHING FOR OBJECTS WITHIN THEM: contextual associations have been shown to modulate reaction time and object recognition accuracy, as well as influence the distribution of eye movements and patterns of brain activations. However, we have not yet systematically quantified the relationships between objects and their scene environments. Here I seek to fill this gap by providing descriptive statistics of object-scene relationships. A total of 48, 167 objects were hand-labeled in 3499 scenes using the LabelMe tool (Russell et al., 2008). From these data, I computed a variety of descriptive statistics at three different levels of analysis: the ensemble statistics that describe the density and spatial distribution of unnamed "things" in the scene; the bag of words level where scenes are described by the list of objects contained within them; and the structural level where the spatial distribution and relationships between the objects are measured. The utility of each level of description for scene categorization was assessed through the use of linear classifiers, and the plausibility of each level for modeling human scene categorization is discussed. Of the three levels, ensemble statistics were found to be the most informative (per feature), and also best explained human patterns of categorization errors. Although a bag of words classifier had similar performance to human observers, it had a markedly different pattern of errors. However, certain objects are more useful than others, and ceiling classification performance could be achieved using only the 64 most informative objects. As object location tends not to vary as a function of category, structural information provided little additional information. Additionally, these data provide valuable information on natural scene redundancy that can be exploited for machine vision, and can help the visual cognition community to design experiments guided by statistics

  8. Detonation Properties of Ammonium Dinitramide (ADN)

    Science.gov (United States)

    Wätterstam, A.; Östmark, H.; Helte, A.; Karlsson, S.

    1999-06-01

    Ammonium Dinitramide, ADN, has a potential as an oxidizer for underwater high explosives. Pure ADN has a large reaction-zone length and shows a strong non-ideal behaviour. The work presented here is an extension of previous work.(Sensitivity and Performance Characterization of Ammonium Dinitramide (ADN). Presented at 11th International Detonation Symposium, Snowmass, CO, 1998.) Experiments for determining the detonation velocity as a function of inverse charge radius and density, reaction-zone length and curvature, and the detonation pressure are presented. Measurements of pressure indicates that no, or weak von-Neumann spike exists, suggesting an immediate chemical decomposition. Experimental data are compared with predicted using thermochemical codes and ZND-theory.

  9. Progress in the High Level Trigger Integration

    CERN Multimedia

    Cristobal Padilla

    2007-01-01

    During the week from March 19th to March 23rd, the DAQ/HLT group performed another of its technical runs. On this occasion the focus was on integrating the Level 2 and Event Filter triggers, with a much fuller integration of HLT components than had been done previously. For the first time this included complete trigger slices, with a menu to run the selection algorithms for muons, electrons, jets and taus at the Level-2 and Event Filter levels. This Technical run again used the "Pre-Series" system (a vertical slice prototype of the DAQ/HLT system, see the ATLAS e-news January issue for details). Simulated events, provided by our colleagues working in the streaming tests, were pre-loaded into the ROS (Read Out System) nodes. These are the PC's where the data from the detector is stored after coming out of the front-end electronics, the "first part of the TDAQ system" and the interface to the detectors. These events used a realistic beam interaction mixture and had been subjected to a Level-1 selection. The...

  10. Statistics of High-level Scene Context

    Directory of Open Access Journals (Sweden)

    Michelle R. Greene

    2013-10-01

    Full Text Available Context is critical to our ability to recognize environments and to search for objects within them: contextual associations have been shown to modulate reaction time and object recognition accuracy, as well as influence the distribution of eye movements and patterns of brain activations. However, we have not yet systematically quantified the relationships between objects and their scene environments. Here I seek to fill this gap by providing descriptive statistics of object-scene relationships. A total of 48,167 objects were hand-labeled in 3499 scenes using the LabelMe tool (Russell, Torralba, Muphy & Freeman, 2008. From these data, I computed a variety of descriptive statistics at three different levels of analysis: the ensemble statistics that describe the density and spatial distribution of unnamed things in the scene; the bag of words level where scenes are described by the list of objects contained within them; and the structural level where the spatial distribution and relationships between the objects are measured. The utility of each level of description for scene categorization was assessed through the use of linear classifiers, and the plausibility of each level for modeling human rapid scene categorization is discussed. Ensemble statistics were found to be the most informative (per feature, and also best explained human patterns of categorization errors. Although a bag of words classifier had similar performance to human observers, it had a markedly different pattern of errors. Some objects are more useful than others, and ceiling classification performance could be achieved using only the 64 most informative objects. As object location tends not to vary as a function of category, structural information provided little additional information. Additionally, these data provide valuable information on natural scene redundancy that can be exploited for machine vision, and can help researchers in visual cognition design new data

  11. Ammonium Metabolism Enzymes Aid Helicobacter pylori Acid Resistance

    OpenAIRE

    2014-01-01

    The gastric pathogen Helicobacter pylori possesses a highly active urease to support acid tolerance. Urea hydrolysis occurs inside the cytoplasm, resulting in the production of NH3 that is immediately protonated to form NH4+. This ammonium must be metabolized or effluxed because its presence within the cell is counterproductive to the goal of raising pH while maintaining a viable proton motive force (PMF). Two compatible hypotheses for mitigating intracellular ammonium toxicity include (i) th...

  12. Food and Nutrition Curriculum Guide for Florida. Elementary Level, Middle/Junior High Level, Senior High Level, Post-Secondary Level.

    Science.gov (United States)

    Crabtree, Myrna P.; Baum, Rosemere

    This curriculum guide contains competency-based curricula suggested for teaching foods and nutrition courses on the elementary, middle/junior high school, senior high school, and postsecondary levels in Florida. For each level, concepts and subconcepts are presented, referenced to competencies or terminal performance objectives. For each…

  13. High-level Behavior Representation Languages Revisited

    Science.gov (United States)

    2016-06-07

    Newell, A. (1980). The keystroke-level model for user performance time with interactive systems. Communications of the ACM , 23(7), 396-410. Cohen, M. A... ACM Conference on Human Factors in Computing Systems, CHI󈧊. New York, NY: ACM . Howes, A., Lewis, R. L., Vera, A., & Richardson, J. (2005...modeling made easy. In Proceedings of CHI 2004 (Vienna, Austria, April 2004), 455-462. New York, NY: ACM . Jones, R. M., Crossman, J. A. L., Lebiere, C

  14. Globalism on the High School Level.

    Science.gov (United States)

    Presutti, Robert M.

    1997-01-01

    Describes the International Sibling Program at Lewiston-Porter High School in Youngstown, New York. Notes that 10 "sibling schools" in eight countries participate by exchanging faculty and students. Suggests that the program has given students, staff, and the community many opportunities to interact with the real world. (RS)

  15. The ferrous ammonium sulfate solid system, as dosemeter for processes at low temperatures and high doses of gamma radiation; El sistema sulfato ferroso amoniacal solido, como dosimetro para procesos a bajas temperaturas y altas dosis de radiacion gamma

    Energy Technology Data Exchange (ETDEWEB)

    Juarez C, J.M.; Ramos B, S.; Negron M, A. [ICN-UNAM, 04510 Mexico D.F. (Mexico)

    2005-07-01

    This paper presents the results obtained from a study of the radiation induced oxidation of crystalline ferrous ammonium sulfate with gamma rays at 295 K, 263 K and 77 K and dose from 0 to 300 kGy. The radiation induced decomposition of ferrous ammonium sulfate has been studied by the dissolution of the irradiated salt in 0,8 N sulfuric acid. The main product is Fe{sup 3+} and molar concentration of ferric ion was determined spectrophotometrically in the UV region at 304 nm. The optical density values showed a linear dependence with dose, indicating that the data obtained might be used to create a calibrating curve. Color in irradiated salt changes from blue to green, yellow and orange according to the absorbed dose. The accuracy and the reproducibility of the system were tested. In addition, some other characteristics make possible the use of this system as a dosimeter, similar to Fricke chemical dosemeter, at low temperatures and high dose. (Author)

  16. Synthesis and Antibacterial Activity of Novel Quaternary Ammonium Pyridoxine Derivatives.

    Science.gov (United States)

    Shtyrlin, Nikita V; Sapozhnikov, Sergey V; Koshkin, Sergey A; Iksanova, Alfiya G; Sabirov, Arthur H; Kayumov, Airat R; Nureeva, Aliya A; Zeldi, Marina I; Shtyrlin, Yurii G

    2015-01-01

    A series of 26 quaternary ammonium pyridoxine derivatives were synthesized and their cytotoxicity and antibacterial activities against clinically relevant bacterial strains were tested in vitro. The antibacterial activity of mono-ammonium salts increased with the rise of the lipophilicity and compound 3,3,5-trimethyl-8,8-dioctyl-1,7,8,9-tetrahydro-[1,3]dioxino[5,4-d]pyrrolo[3,4-b]pyridin-8-ium chloride (2d) reaches a maximum among them. Bis-ammonium salt of pyridoxine 4 with two dimethyloctylamine groups also demonstrated high antibacterial activity despite lower lipophilicity. The results of MTT assay indicated that HEK 293 cells were more sensitive than HSF to quaternary ammonium pyridoxine derivatives. Compounds 2d and 4 did not induce the damage of the DNA and might be of interest in the development of new antimicrobials.

  17. Speech at the High-level Dialogue

    Institute of Scientific and Technical Information of China (English)

    Yu; Hongjun

    2014-01-01

    <正>The commemoration of 2014 International Day of Peace,themed with"A More Secure Asia Aspired by People"is highly relevant.To begin with,I would like to share 3 points on Asian security with you.Firstly,problems in the realm of traditional security are worrying.Outdated security perspectives and security systemic structures left by the cold war are threatening Asian peace and development,yet some countries still believe in backward security

  18. Cloning, high-level expression, purification and characterization of a ...

    African Journals Online (AJOL)

    Cloning, high-level expression, purification and characterization of a staphylokinase variant, SakøC, ... African Journal of Biotechnology ... Hence in this study, we reported the cloning, high-level expression, purification and characterization of ...

  19. Feedback inhibition of ammonium uptake by a phospho-dependent allosteric mechanism in Arabidopsis.

    Science.gov (United States)

    Lanquar, Viviane; Loqué, Dominique; Hörmann, Friederike; Yuan, Lixing; Bohner, Anne; Engelsberger, Wolfgang R; Lalonde, Sylvie; Schulze, Waltraud X; von Wirén, Nicolaus; Frommer, Wolf B

    2009-11-01

    The acquisition of nutrients requires tight regulation to ensure optimal supply while preventing accumulation to toxic levels. Ammonium transporter/methylamine permease/rhesus (AMT/Mep/Rh) transporters are responsible for ammonium acquisition in bacteria, fungi, and plants. The ammonium transporter AMT1;1 from Arabidopsis thaliana uses a novel regulatory mechanism requiring the productive interaction between a trimer of subunits for function. Allosteric regulation is mediated by a cytosolic C-terminal trans-activation domain, which carries a conserved Thr (T460) in a critical position in the hinge region of the C terminus. When expressed in yeast, mutation of T460 leads to inactivation of the trimeric complex. This study shows that phosphorylation of T460 is triggered by ammonium in a time- and concentration-dependent manner. Neither Gln nor l-methionine sulfoximine-induced ammonium accumulation were effective in inducing phosphorylation, suggesting that roots use either the ammonium transporter itself or another extracellular sensor to measure ammonium concentrations in the rhizosphere. Phosphorylation of T460 in response to an increase in external ammonium correlates with inhibition of ammonium uptake into Arabidopsis roots. Thus, phosphorylation appears to function in a feedback loop restricting ammonium uptake. This novel autoregulatory mechanism is capable of tuning uptake capacity over a wide range of supply levels using an extracellular sensory system, potentially mediated by a transceptor (i.e., transporter and receptor).

  20. Bumblebee pupae contain high levels of aluminium.

    Directory of Open Access Journals (Sweden)

    Christopher Exley

    Full Text Available The causes of declines in bees and other pollinators remains an on-going debate. While recent attention has focussed upon pesticides, other environmental pollutants have largely been ignored. Aluminium is the most significant environmental contaminant of recent times and we speculated that it could be a factor in pollinator decline. Herein we have measured the content of aluminium in bumblebee pupae taken from naturally foraging colonies in the UK. Individual pupae were acid-digested in a microwave oven and their aluminium content determined using transversely heated graphite furnace atomic absorption spectrometry. Pupae were heavily contaminated with aluminium giving values between 13.4 and 193.4 μg/g dry wt. and a mean (SD value of 51.0 (33.0 μg/g dry wt. for the 72 pupae tested. Mean aluminium content was shown to be a significant negative predictor of average pupal weight in colonies. While no other statistically significant relationships were found relating aluminium to bee or colony health, the actual content of aluminium in pupae are extremely high and demonstrate significant exposure to aluminium. Bees rely heavily on cognitive function and aluminium is a known neurotoxin with links, for example, to Alzheimer's disease in humans. The significant contamination of bumblebee pupae by aluminium raises the intriguing spectre of cognitive dysfunction playing a role in their population decline.

  1. Bumblebee pupae contain high levels of aluminium.

    Science.gov (United States)

    Exley, Christopher; Rotheray, Ellen; Goulson, David

    2015-01-01

    The causes of declines in bees and other pollinators remains an on-going debate. While recent attention has focussed upon pesticides, other environmental pollutants have largely been ignored. Aluminium is the most significant environmental contaminant of recent times and we speculated that it could be a factor in pollinator decline. Herein we have measured the content of aluminium in bumblebee pupae taken from naturally foraging colonies in the UK. Individual pupae were acid-digested in a microwave oven and their aluminium content determined using transversely heated graphite furnace atomic absorption spectrometry. Pupae were heavily contaminated with aluminium giving values between 13.4 and 193.4 μg/g dry wt. and a mean (SD) value of 51.0 (33.0) μg/g dry wt. for the 72 pupae tested. Mean aluminium content was shown to be a significant negative predictor of average pupal weight in colonies. While no other statistically significant relationships were found relating aluminium to bee or colony health, the actual content of aluminium in pupae are extremely high and demonstrate significant exposure to aluminium. Bees rely heavily on cognitive function and aluminium is a known neurotoxin with links, for example, to Alzheimer's disease in humans. The significant contamination of bumblebee pupae by aluminium raises the intriguing spectre of cognitive dysfunction playing a role in their population decline.

  2. 76 FR 62311 - Ammonium Nitrate Security Program

    Science.gov (United States)

    2011-10-07

    ... to best notify agents (AN Agents) when ammonium nitrate purchasers (AN Purchasers) submit those AN... directly to ammonium nitrate sellers (AN Sellers) when it is not possible for an AN Seller to verify the...

  3. 40 CFR 227.30 - High-level radioactive waste.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 24 2010-07-01 2010-07-01 false High-level radioactive waste. 227.30...-level radioactive waste. High-level radioactive waste means the aqueous waste resulting from the operation of the first cycle solvent extraction system, or equivalent, and the concentrated waste from...

  4. A High-Voltage Level Tolerant Transistor Circuit

    NARCIS (Netherlands)

    Annema, Anne Johan; Geelen, Godefridus Johannes Gertrudis Maria

    2001-01-01

    A high-voltage level tolerant transistor circuit, comprising a plurality of cascoded transistors, including a first transistor (T1) operatively connected to a high-voltage level node (3) and a second transistor (T2) operatively connected to a low-voltage level node (2). The first transistor (T1) con

  5. 21 CFR 582.7133 - Ammonium alginate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Ammonium alginate. 582.7133 Section 582.7133 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Ammonium alginate. (a) Product. Ammonium alginate. (b) Conditions of use. This substance is...

  6. 21 CFR 582.1141 - Ammonium phosphate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Ammonium phosphate. 582.1141 Section 582.1141 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Additives § 582.1141 Ammonium phosphate. (a) Product. Ammonium phosphate (mono- and dibasic). (b)...

  7. 76 FR 11273 - Ammonium Nitrate From Russia

    Science.gov (United States)

    2011-03-01

    ... COMMISSION Ammonium Nitrate From Russia AGENCY: United States International Trade Commission. ACTION: Institution of a five-year review concerning the suspended investigation on ammonium nitrate from Russia... investigation on ammonium nitrate from Russia would be likely to lead to continuation or recurrence of...

  8. 76 FR 47238 - Ammonium Nitrate From Russia

    Science.gov (United States)

    2011-08-04

    ... COMMISSION Ammonium Nitrate From Russia Determination On the basis of the record \\1\\ developed in the subject... order on ammonium nitrate from Russia would be likely to lead to continuation or recurrence of material... Commission are contained in USITC Publication 4249 (August 2011), entitled Ammonium Nitrate from...

  9. Metabolic engineering of a diazotrophic bacterium improves ammonium release and biofertilization of plants and microalgae.

    Science.gov (United States)

    Ambrosio, Rafael; Ortiz-Marquez, Juan Cesar Federico; Curatti, Leonardo

    2017-03-01

    The biological nitrogen fixation carried out by some Bacteria and Archaea is one of the most attractive alternatives to synthetic nitrogen fertilizers. However, with the exception of the symbiotic rhizobia-legumes system, progress towards a more extensive realization of this goal has been slow. In this study we manipulated the endogenous regulation of both nitrogen fixation and assimilation in the aerobic bacterium Azotobacter vinelandii. Substituting an exogenously inducible promoter for the native promoter of glutamine synthetase produced conditional lethal mutant strains unable to grow diazotrophically in the absence of the inducer. This mutant phenotype could be reverted in a double mutant strain bearing a deletion in the nifL gene that resulted in constitutive expression of nif genes and increased production of ammonium. Under GS non-inducing conditions both the single and the double mutant strains consistently released very high levels of ammonium (>20mM) into the growth medium. The double mutant strain grew and excreted high levels of ammonium under a wider range of concentrations of the inducer than the single mutant strain. Induced mutant cells could be loaded with glutamine synthetase at different levels, which resulted in different patterns of extracellular ammonium accumulation afterwards. Inoculation of the engineered bacteria into a microalgal culture in the absence of sources of C and N other than N2 and CO2 from the air, resulted in a strong proliferation of microalgae that was suppressed upon addition of the inducer. Both single and double mutant strains also promoted growth of cucumber plants in the absence of added N-fertilizer, while this property was only marginal in the parental strain. This study provides a simple synthetic genetic circuit that might inspire engineering of optimized inoculants that efficiently channel N2 from the air into crops. Copyright © 2017 International Metabolic Engineering Society. Published by Elsevier Inc. All

  10. Modification of the Farr assay using ethanol-ammonium acetate precipitation and its application to the measurement of affinity of anti-HCG produced in several species.

    Science.gov (United States)

    Thanavala, Y M; Hay, F C

    1978-01-01

    A double isotope modified Farr assay was used to determine the total binding sites and affinity of antibodies to human chorionic gonadotrophin. Precipitation of the antigen--antibody complex at equilibrium with ammonium sulphate gave very high levels of nonspecific binding. Good discrimination over background was observed using a specific anti-immunoglobulin serum. However since we were interested in measuring the affinity of antibodies raised in several animal species it was more appropriate to use a single nonspecies precipitating reagent. We found that the use of a mixture of ethanol-ammonium acetate gave very low levels of non-specific binding in baboons, marmosets, rabbits and mice.

  11. Interaction between Ammonium Toxicity and Green Tide Development Over Seagrass Meadows

    DEFF Research Database (Denmark)

    Marin, Francisco Moreno; Vergara, Juan J.; Pérez-Llorens, J. Lucas

    2016-01-01

    Eutrophication affects seagrasses negatively by increasing light attenuation through stimulation of biomass of fast-growing, bloom-forming algae and because high concentrations of ammonium in the water can be toxic to higher plants. We hypothesized nevertheless, that moderate amounts of nitrophilic...... influence on the performance of Z. noltei. The presence of Ulva sp. without ammonium supply had a similar, but slightly smaller, negative effect on seagrass fitness due to light attenuation. When ammonium enrichment was combined with presence of Ulva sp., Ulva sp. ameliorated some of negative effects caused...... by high ammonium availability although Ulva sp. lowered the availability of light. Benthic microalgae, which increased in biomass during the experiment, seemed to play a similar role as Ulva sp.–they contributed to remove ammonium from the water, and thus, aided to keep the ammonium concentrations...

  12. Analysis of Cyberbullying Sensitivity Levels of High School Students and Their Perceived Social Support Levels

    Science.gov (United States)

    Akturk, Ahmet Oguz

    2015-01-01

    Purpose: The purpose of this paper is to determine the cyberbullying sensitivity levels of high school students and their perceived social supports levels, and analyze the variables that predict cyberbullying sensitivity. In addition, whether cyberbullying sensitivity levels and social support levels differed according to gender was also…

  13. Analysis of Cyberbullying Sensitivity Levels of High School Students and Their Perceived Social Support Levels

    Science.gov (United States)

    Akturk, Ahmet Oguz

    2015-01-01

    Purpose: The purpose of this paper is to determine the cyberbullying sensitivity levels of high school students and their perceived social supports levels, and analyze the variables that predict cyberbullying sensitivity. In addition, whether cyberbullying sensitivity levels and social support levels differed according to gender was also…

  14. Practical Use of High-level Petri Net

    DEFF Research Database (Denmark)

    The aim of the workshop is to bring together researchers and practitioners with interests in the use of high-level nets and their tools for practical applications. A typical paper is expected to report on a case study where high-level Petri nets and their tools have been used in practice. We also...... welcome papers describing a tool, a methodology, or other developments that have proved successful to make high-level Petri nets more applicable in practice....

  15. Water-level change, High Plains aquifer, 1980 to 1995

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This raster data set represents water-level change in the High Plains aquifer of the United States from 1980 to 1995, in feet. The High Plains aquifer underlies...

  16. Water-level change, High Plains aquifer, 1995 to 2000

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This raster data set represents water-level change in the High Plains aquifer of the United States from 1995 to 2000, in feet. The High Plains aquifer underlies...

  17. Water-level change, High Plains aquifer, 2005 to 2009

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This raster data set represents water-level change in the High Plains aquifer of the United States from 2005 to 2009, in feet. The High Plains aquifer underlies...

  18. Water-level change, High Plains aquifer, 2000 to 2005

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This raster data set represents water-level change in the High Plains aquifer of the United States from 2000 to 2005, in feet. The High Plains aquifer underlies...

  19. A maritime pine antimicrobial peptide involved in ammonium nutrition.

    Science.gov (United States)

    Canales, Javier; Avila, Concepción; Cánovas, Francisco M

    2011-09-01

    A large family of small cysteine-rich antimicrobial peptides (AMPs) is involved in the innate defence of plants against pathogens. Recently, it has been shown that AMPs may also play important roles in plant growth and development. In previous work, we have identified a gene of the AMP β-barrelin family that was differentially regulated in the roots of maritime pine (Pinus pinaster Ait.) in response to changes in ammonium nutrition. Here, we present the molecular characterization of two AMP genes, PpAMP1 and PpAMP2, showing different molecular structure and physicochemical properties. PpAMP1 and PpAMP2 displayed different expression patterns in maritime pine seedlings and adult trees. Furthermore, our expression analyses indicate that PpAMP1 is the major form of AMP in the tree, and its relative abundance is regulated by ammonium availability. In contrast, PpAMP2 is expressed at much lower levels and it is not regulated by ammonium. To gain new insights into the function of PpAMP1, we over-expressed the recombinant protein in Escherichia coli and demonstrated that PpAMP1 strongly inhibited yeast growth, indicating that it exhibits antimicrobial activity. We have also found that PpAMP1 alters ammonium uptake, suggesting that it is involved in the regulation of ammonium ion flux into pine roots.

  20. Performance of sulfate-dependent anaerobic ammonium oxidation

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    The performance of sulfate-dependent anaerobic ammonium oxidation was studied.The results showed that both SO42-and NH4+ were chemically stable under anaerobic conditions.They did not react with each other in the absence of biological catalyst(sludge).The anaerobic digested sludge cultivated in an anaerobic reactor for three years took on the ability of oxidizing ammonium with sulfate anaero-bically.The average reduction of sulfate and ammonium was 71.67 mg.L-1 and 56.82 mg.L-1 at high concentrations.The reaction between SO42-and NH4+ was difficult,though feasible,due to its low standard Gibbs free energy change.The experiment demonstrated that high substrate concentrations and low oxidation-reduction potential(ORP) may be favourable for the biological reaction.

  1. Performance of sulfate-dependent anaerobic ammo-nium oxidation

    Institute of Scientific and Technical Information of China (English)

    ZHANG Lei; ZHENG Ping; HE YuHui; JIN RenCun

    2009-01-01

    The performance of sulfate-dependent anaerobic ammonium oxidation was studied. The results showed that both SO42- and NH4+ were chemically stable under anaerobic conditions. They did not react with each other in the absence of biological catalyst (sludge). The anaerobic digested sludge cultivated in an anaerobic reactor for three years took on the ability of oxidizing ammonium with sulfate anaero-bically. The average reduction of sulfate and ammonium was 71.67 mg.L-1 and 56.82 mg.L-1 at high concentrations.The reaction between SO42- and NH4+ was difficult, though feasible, due to its low standard Gibbs free energy change. The experiment demonstrated that high substrate concentrations and low oxidation-reduction potential (ORP) may be favourable for the biological reaction.

  2. Process for solidifying high-level nuclear waste

    Science.gov (United States)

    Ross, Wayne A.

    1978-01-01

    The addition of a small amount of reducing agent to a mixture of a high-level radioactive waste calcine and glass frit before the mixture is melted will produce a more homogeneous glass which is leach-resistant and suitable for long-term storage of high-level radioactive waste products.

  3. Studies on Biquaternary Ammonium Salt Algaecide for Removing Red Tide Algae

    Institute of Scientific and Technical Information of China (English)

    刘洁生; 张珩; 杨维东; 高洁; 柯琼

    2004-01-01

    The paper deals with the removal and control of red tide algae, Phaeoecystis globosa and Alexandrium tamarense by biquaternary ammonium salt algaecide. The results show that the efficient concentration of biquaternary ammonium salt to control the two algaes in 96 h is 0.8 mg · L-1 and 0.4 mg · L-1, respectively. It is found that biquaternary ammonium salt has high efficiency and longer duration of action in the removal and control of algae.Biquaternary ammonium salt might be an excellent algaecide to control HAB.

  4. On the influence of thiamine and ammonium ions on alcoholic fermentation

    NARCIS (Netherlands)

    Maesen, Th.J.M.

    1953-01-01

    1. 1. In a glucose-sodium acetate medium of pH 5.6 the fermentation rate of bakers' yeast remains constant at a low level during several hours, while in the presence of ammonium sulphate it gradually increases. The rise is steeper in the presence of thiamine. 2. 2. After the ammonium ions have been

  5. On the influence of thiamine and ammonium ions on alcoholic fermentation

    NARCIS (Netherlands)

    Maesen, Th.J.M.

    1953-01-01

    1. 1. In a glucose-sodium acetate medium of pH 5.6 the fermentation rate of bakers' yeast remains constant at a low level during several hours, while in the presence of ammonium sulphate it gradually increases. The rise is steeper in the presence of thiamine. 2. 2. After the ammonium ions have

  6. On the influence of thiamine and ammonium ions on alcoholic fermentation

    NARCIS (Netherlands)

    Maesen, Th.J.M.

    1953-01-01

    1. 1. In a glucose-sodium acetate medium of pH 5.6 the fermentation rate of bakers' yeast remains constant at a low level during several hours, while in the presence of ammonium sulphate it gradually increases. The rise is steeper in the presence of thiamine. 2. 2. After the ammonium ions have been

  7. Floorplan-Driven Multivoltage High-Level Synthesis

    Directory of Open Access Journals (Sweden)

    Xianwu Xing

    2009-01-01

    Full Text Available As the semiconductor technology advances, interconnect plays a more and more important role in power consumption in VLSI systems. This also imposes a challenge in high-level synthesis, in which physical information is limited and conventionally considered after high-level synthesis. To close the gap between high-level synthesis and physical implementation, integration of physical synthesis and high-level synthesis is essential. In this paper, a technique named FloM is proposed for integrating floorplanning into high-level synthesis of VLSI system with multivoltage datapath. Experimental results obtained show that the proposed technique is effective and the energy consumed by both the datapath and the wires can be reduced by more than 40%.

  8. Treating ammonium-rich wastewater with sludge from water treatment plant to produce ammonium alum

    Directory of Open Access Journals (Sweden)

    Wen-Po Cheng

    2016-03-01

    Full Text Available This study applies a process to treat ammonium-rich wastewater using alum-generated sludge form water purification plant, and gain economic benefit by producing ammonium alum (Al(NH4(SO42·12H2O. The factors affecting production of ammonium alum include molar ratio of ammonium to aluminum concentration, sulfuric acid concentration, mixing speed, mixing time, standing time, and temperature. According to the equation for the ammonium removal reaction, the theoretical quantity of ammonium alum was calculated based on initial and final concentrations of ammonium. Then, the weight of ammonium alum crystal was divided by the theoretical weight to derive the recovery ratio. The optimum sludge and sulfuric acid dosage to treat about 17 g L−1 ammonium wastewater are 300 g L−1 and 100 mL L−1, respectively. The optimal dosage for wastewater is molar ratio of ammonium to aluminum of about 1 due to the aluminum dissolving in acidified wastewater. The ammonium removal efficiency is roughly 70% and the maximum recovery ratio for ammonium alum is 93% when the wastewater is mixed for 10 min at the mixing velocity gradient of 100 s−1. Ammonium alum production or ammonium removal can be enhanced by controlling the reaction at low temperatures.

  9. Carboxylates and the uptake of ammonium by excised maize roots

    NARCIS (Netherlands)

    Breteler, H.

    1975-01-01

    The effect of carboxylates (organic acid anions) on NH 4 uptake was studied by changing the carboxylate level of roots prior to uptake experi ments. Succinate was the most effective stimulator of ammonium uptake. The oxocarboxylates (α-oxoglutarate, oxaloacetate and

  10. Removing ammonium from water using modified corncob-biochar.

    Science.gov (United States)

    Vu, Thi Mai; Trinh, Van Tuyen; Doan, Dinh Phuong; Van, Huu Tap; Nguyen, Tien Vinh; Vigneswaran, Saravanamuthu; Ngo, Huu Hao

    2017-02-01

    Ammonium pollution in groundwater and surface water is of major concern in many parts of the world due to the danger it poses to the environment and people's health. This study focuses on the development of a low cost adsorbent, specifically a modified biochar prepared from corncob. Evaluated here is the efficiency of this new material for removing ammonium from synthetic water (ammonium concentration from 10 to 100mg/L). The characteristics of the modified biochar were determined by Brunauer-Emmett-Teller (BET) test, Fourier transform infrared spectroscopy (FTIR) and Scanning electron microscopy (SEM). It was found that ammonium adsorption on modified biochar strongly depended on pH. Adsorption kinetics of NH4(+)-N using modified biochar followed the pseudo-second order kinetic model. Both Langmuir and Sips adsorption isotherm models could simulate well the adsorption behavior of ammonium on modificated biochar. The highest adsorption capacity of 22.6mg NH4(+)-N/g modified biochar was obtained when the biochar was modified by soaking it in HNO3 6M and NaOH 0.3M for 8h and 24h, respectively. The high adsorption capacity of the modified biochar suggested that it is a promising adsorbent for NH4(+)-N remediation from water.

  11. The effect of high altitude on nasal nitric oxide levels.

    Science.gov (United States)

    Altundag, Aytug; Salihoglu, Murat; Cayonu, Melih; Cingi, Cemal; Tekeli, Hakan; Hummel, Thomas

    2014-09-01

    The aim of the present study was to investigate whether nasal nitric oxide (nNO) levels change in relation to high altitude in a natural setting where the weather conditions were favorable. The present study included 41 healthy volunteers without a history of acute rhinosinusitis within 3 weeks and nasal polyposis. The study group consisted of 31 males (76 %) and 10 females (24 %) and the mean age of the study population was 38 ± 10 years. The volunteers encamped for 2 days in a mountain village at an altitude of 1,500 m above sea level (masl) and proceeded to highlands at an altitude of 2,200 masl throughout the day. The measurements of nNO were done randomly, either first at the mountain village or at sea level. Each participant had nNO values both at sea level and at high altitude at the end of the study. The nNO values of sea level and high altitude were compared to investigate the effect of high altitude on nNO levels. The mean of average nNO measurements at the high altitude was 74.2 ± 41 parts-per-billion (ppb) and the mean of the measurements at sea level was 93.4 ± 45 ppb. The change in nNO depending on the altitude level was statistically significant (p high altitude even if the weather conditions were favorable, such as temperature, humidity, and wind.

  12. Cover crops affecting levels of ammonium and nitrate in the soil and upland rice developmentPlantas de cobertura afetando os níveis de nitrato e amônio no solo e o desenvolvimento do arroz de terras altas

    Directory of Open Access Journals (Sweden)

    Adriano Stephan Nascente

    2013-10-01

    Full Text Available The use of cover crops in no-tillage systems (NTS increases the levels of organic matter and could increase the nitrogen content of the soil, contributing to reduce fertilizers costs. The knowledge of these processes is fundamental for deciding whether cover crops can be effectively incorporated into the agricultural production system. The objective of this study was to evaluate the effect of cover crop species on the levels of nitrate and ammonium in the soil in early upland rice development, as well upland rice yield. A field experiment was performed and treatments consisted of growing rice on five cover crops (Panicum maximum, Brachiaria ruziziensis, Brachiaria brizantha, millet and fallow in an NTS and two control treatments (Brachiaria brizantha and fallow under a conventional tillage system, CTS, (one plowing and two disking. The experimental design was a complete randomized block with three replications. The soil samples were collected during a period of six weeks (0, 7, 14, 21, 28 and 35 days in relation to upland rice sowing. The cover crops Brachiaria brizantha, Panicum maximum and Brachiaria ruziziensis in the NTS and B. brizantha fallow incorporated into the CTS favored higher levels of nitrate in the soil. In contrast, B. brizantha and fallow in the CTS and millet and P. maximum in the NTS favored the buildup of high levels of ammonium in the soil. The treatments under the plowed cover crops millet and fallow allowed for a higher upland rice yield. The tillage system and nature of the cover crops could be used to achieve the desired levels and forms of nitrogen in soil. O uso de plantas de cobertura no sistema plantio direto (SPD aumenta os níveis de matéria orgânica e pode ajudar a aumentar os teores de nitrogênio no solo contribuindo para reduzir os custos de fertilizantes. O conhecimento desse processo é fundamental para que as plantas de cobertura possam ser efetivamente incorporadas aos sistemas de produção agrícola. O

  13. Relations of ammonium minerals at several hydrothermal systems in the western U.S.

    Science.gov (United States)

    Krohn, M. Dennis; Kendall, Carol; Evans, John R.; Fries, Terry L.

    1993-08-01

    Ammonium bound to silicate and sulfate minerals has recently been located at several major hydrothermal systems in the western U.S. utilizing newly-discovered near-infrared spectral properties. Knowledge of the origin and mineralogic relations of ammonium minerals at known hydrothermal systems is critical for the proper interpretation of remote sensing data and for testing of possible links to mineralization. Submicroscopic analysis of ammonium minerals from two mercury- and gold-bearing hot-springs deposits at Ivanhoe, Nevada and McLaughlin, California shows that the ammonium feldspar, buddingtonite, occurs as fine-grained euhedral crystals coating larger sulfide and quartz crystals. Ammonium feldspar seems to precipitate relatively late in the crystallization sequence and shows evidence for replacement of NH 4 + by K + or other monovalent cations. Some buddingtonite is observed in close association with mercury, but not with gold. Ammonioalunite is found in a variety of isolated crystal forms at both deposits. Nitrogen isotopic values for ammonium-bearing minerals show a 14‰ range in composition, precluding assignment of a specific provenance to the nitrogen. The correlations of nitrogen isotopic values with depth and ammonium content suggest some loss of nitrogen in the oxidizing supergene environment, possibly as a metastable mineral. The high ammonium content in these hydrothermal systems, the close association to mercury, and the small crystal size of the ammonium-bearing minerals all suggest that ammonium may be transported in a late-stage vapor phase or as an organic volatile. Such a process could lead to the formation of a non-carbonaceous organic aureole above a buried geothermal source. The discovery of a 10-km outcrop of ammonium minerals confirms that significant substitution of ammonium in minerals is possible over an extensive area and that remote sensing is a feasible means to detect such aureoles.

  14. The Reliability of Highly Elevated CA 19-9 Levels

    Directory of Open Access Journals (Sweden)

    B. R. Osswald

    1993-01-01

    Full Text Available CA 19-9 is used as a tumour marker of the upper gastrointestinal tract. However, extremely elevated CA 19-9 levels are found also in patients with benign diseases. Cholestasis was present in 97.1 % of patients with high elevated CA 19-9, independent of their primary disease. 50% of patients with non-malignant diseases and increased CA 19-9 levels showed liver cirrhosis, cholecystitis, pancreatitis and/or hepatitis. In 8.8% no explanation was found for the extremely high CA 19-9 level. The results provide evidence of different factors influencing the CA 19-9 level.

  15. Rocket Solid Propellant Alternative Based on Ammonium Dinitramide

    Directory of Open Access Journals (Sweden)

    Grigore CICAN

    2017-03-01

    Full Text Available Due to the continuous run for a green environment the current article proposes a new type of solid propellant based on the fairly new synthesized oxidizer, ammonium dinitramide (ADN. Apart of having a higher specific impulse than the worldwide renowned oxidizer, ammonium perchlorate, ADN has the advantage, of leaving behind only nitrogen, oxygen and water after decomposing at high temperatures and therefore totally avoiding the formation of hydrogen chloride fumes. Based on the oxidizer to fuel ratios of the current formulations of the major rocket solid booster (e.g. Space Shuttle’s SRB, Ariane 5’s SRB which comprises mass variations of ammonium perchlorate oxidizer (70-75%, atomized aluminum powder (10-18% and polybutadiene binder (12-20% a new solid propellant was formulated. As previously stated, the new propellant formula and its variations use ADN as oxidizer and erythritol tetranitrate as fuel, keeping the same polybutadiene as binder.

  16. High-level waste immobilization program: an overview

    Energy Technology Data Exchange (ETDEWEB)

    Bonner, W.R.

    1979-09-01

    The High-Level Waste Immobilization Program is providing technology to allow safe, affordable immobilization and disposal of nuclear waste. Waste forms and processes are being developed on a schedule consistent with national needs for immobilization of high-level wastes stored at Savannah River, Hanford, Idaho National Engineering Laboratory, and West Valley, New York. This technology is directly applicable to high-level wastes from potential reprocessing of spent nuclear fuel. The program is removing one more obstacle previously seen as a potential restriction on the use and further development of nuclear power, and is thus meeting a critical technological need within the national objective of energy independence.

  17. Aerosol isotopic ammonium signatures over the remote Atlantic Ocean

    Science.gov (United States)

    Lin, C. T.; Jickells, T. D.; Baker, A. R.; Marca, A.; Johnson, M. T.

    2016-05-01

    We report aerosol ammonium 15N signatures for samples collected from research cruises on the South Atlantic and Caribbean using a new high sensitivity method. We confirm a pattern of isotopic signals from generally light (δ15N -5 to -10‰), for aerosols with very low (ocean, to generally heavier values (δ15N +5 to +10‰), for aerosols collected in temperate and tropical latitudes and with higher ammonium concentrations (>2 nmol m-3). We discuss whether this reflects a mixing of aerosols from two end-members (polluted continental and remote marine emissions), or isotopic fractionation during aerosol transport.

  18. Precipitation of phenyl and phenoxypenicillin from solutions using ammonium sulfate.

    Science.gov (United States)

    Luengo, J M

    1985-09-01

    An easy, rapid, and available method for separating 6-aminopenicillanic acid (6-APA), benzylpenicillin (penicillin G), and other related molecules from aqueous solutions or complex industrial broths is described. A high concentration of ammonium sulphate induces partially or totally the precipitation of the penicillin present in the solutions, while 6-APA, phenylacetic, and phenoxyacetic acid always remain in the supernatant. The filtration through No. 4 Pyrex glass-fiber filter or Whatman 3MM paper permits the separation of the compounds present in the supernatant from the other ones precipitated. The precipitated product was identified, in all cases, as ammonium penicillin. This method is described here for the first time.

  19. Influence of heterogeneous ammonium availability on bacterial community structure and the expression of nitrogen fixation and ammonium transporter genes during in situ bioremediation of uranium-contaminated groundwater

    Energy Technology Data Exchange (ETDEWEB)

    Mouser, P.J.; N' Guessan, A.L.; Elifantz, H.; Holmes, D.E.; Williams, K.H.; Wilkins, M.J.; Long, P.E.; Lovley, D.R.

    2009-04-01

    The impact of ammonium availability on microbial community structure and the physiological status and activity of Geobacter species during in situ bioremediation of uranium-contaminated groundwater was evaluated. Ammonium concentrations varied by as much as two orders of magnitude (<4 to 400 {micro}M) across the study site. Analysis of 16S rRNA gene sequences suggested that ammonium influenced the composition of the microbial community prior to acetate addition with Rhodoferax species predominating over Geobacter species at the site with the highest ammonium, and Dechloromonas species dominating at sites with lowest ammonium. However, once acetate was added, and dissimilatory metal reduction was stimulated, Geobacter species became the predominant organisms at all locations. Rates of U(VI) reduction appeared to be more related to the concentration of acetate that was delivered to each location rather than the amount of ammonium available in the groundwater. In situ mRNA transcript abundance of the nitrogen fixation gene, nifD, and the ammonium importer gene, amtB, in Geobacter species indicated that ammonium was the primary source of nitrogen during in situ uranium reduction, and that the abundance of amtB transcripts was inversely correlated to ammonium levels across all sites examined. These results suggest that nifD and amtB expression by subsurface Geobacter species are closely regulated in response to ammonium availability to ensure an adequate supply of nitrogen while conserving cell resources. Thus, quantifying nifD and amtB expression appears to be a useful approach for monitoring the nitrogen-related physiological status of Geobacter species in subsurface environments during bioremediation. This study also emphasizes the need for more detailed analysis of geochemical/physiological interactions at the field scale, in order to adequately model subsurface microbial processes.

  20. Synthesis of Chitosan Quaternary Ammonium Salts

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A series of N-alkyl or N-aryl chitosan quaternary ammonium salts were prepared via Schiffs base intermediates. Quaternization of N-substituted chitosan derivatives was carried out using methyl iodide to produce water-soluble cationic chitosan quaternary ammonium salt. The products were characterized by IR, 1HNMR and elemental analysis. The degree of substitution of chitosan quaternary ammonium salt was calculated by elemental analysis.

  1. Steady state growth of E. Coli in low ammonium environment

    Science.gov (United States)

    Kim, Minsu; Deris, Barret; Zhang, Zhongge; Hwa, Terry

    2011-03-01

    Ammonium is the preferred nitrogen source for many microorganisms. In medium with low ammonium concentrations, enteric bacteria turn on the nitrogen responsive (ntr) genes to assimilate ammonium. Two proteins in E. coli, Glutamine synthetase (GS) and the Ammonium/methylammonium transporter AmtB play crucial roles in this regard. GS is the major ammonium assimilation enzyme below 1mM of NH4 + . AmtB is an inner membrane protein that transports NH4 + across the cell membrane against a concentration gradient. In order to study ammonium uptake at low NH4 + concentration at neutral pH, we developed a microfluidic flow chamber that maintains a homogenous nutrient environment during the course of exponential cell growth, even at very low concentration of nutrients. Cell growth can be accurately monitored using time-lapse microscopy. We followed steady state growth down to micro-molar range of NH4 + for the wild type and Δ amtB strains. The wild type strain is able to maintain the growth rate from 10mM down to a few uM of NH4 + , while the mutant exhibited reduced growth below ~ 20 ~uM of NH4 + . Simultaneous characterization of the expression levels of GS and AmtB using fluorescence reporters reveals that AmtB is turned on already at 1mM, but contributes to function only below ~ 30 ~uM in the wild-type. Down to ~ 20 ~uM of NH4 + , E.~coli can compensate the loss of AmtB by GS alone.

  2. NOS CO-OPS Water Level Data, Verified, High Low

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset has verified (quality-controlled), daily, high low water level (tide) data from NOAA NOS Center for Operational Oceanographic Products and Services...

  3. Burning high-level TRU waste in fusion fission reactors

    National Research Council Canada - National Science Library

    Shen, Yaosong

    2016-01-01

    .... A new method of burning high-level transuranic (TRU) waste combined with Thorium–Uranium (Th–U) fuel in the subcritical reactors driven by external fusion neutron sources is proposed in this paper...

  4. Growth and Phytoremediation Potential of Watercress Nasturtium officinale R. Br. in Ammonium-rich Wastewater

    Directory of Open Access Journals (Sweden)

    Saied Ali Musavi

    2016-10-01

    Full Text Available Phytoremediation is considered to be eco-friendly and efficient technology for the removal of pollutants present in wastewater. Nowadays the focus is to look for a sustainable approach in developing wastewater treatment capability in rapidly increasing. The main objective of this paper is to review the possibility of using watercress (Nasturtium officinale for the removal of ammonium ion present in high-strength industrial wastewater. It was found that there was no significant reduction of shoot height, root length and total biomass of watercress due to an increase in NH4+ concentrations. Statistical analysis indicates that the length of roots were significantly (P <0.05 increased at NH4+ rich waste water supply levels of 20-25% while compared to the control. The plants accumulated large amounts of ammonium ion or nitrogen in tissues under conditions of abundant supply. The removal efficiency of raw waste water was around 66 % for nitrogen, 23% for calcium,25 % for total hardness, 22% for biological oxygen demand and 38% of chemical oxygen demand. Nutrient removal efficiency was positively correlated with the initial nutrient supply. The results show that N.officinale grown in the fixed mat economic plant-based treatment system may be an effective, low-cost phytoremediation technology to treat water containing a higher concentration of ammonium.

  5. High-Level Waste System Process Interface Description

    Energy Technology Data Exchange (ETDEWEB)

    d' Entremont, P.D.

    1999-01-14

    The High-Level Waste System is a set of six different processes interconnected by pipelines. These processes function as one large treatment plant that receives, stores, and treats high-level wastes from various generators at SRS and converts them into forms suitable for final disposal. The three major forms are borosilicate glass, which will be eventually disposed of in a Federal Repository, Saltstone to be buried on site, and treated water effluent that is released to the environment.

  6. Glucose level regulation via integral high-order sliding modes.

    Science.gov (United States)

    Dorel, Lela

    2011-04-01

    Diabetes is a condition in which the body either does not produce enough insulin, or does not properly respond to it. This causes the glucose level in blood to increase. An algorithm based on Integral High-Order Sliding Mode technique is proposed, which keeps the normal blood glucose level automatically releasing insulin into the blood. The system is highly insensitive to inevitable parametric and model uncertainties, measurement noises and small delays.

  7. Probing high energy levels of lanthanide ions - experiment and theory

    NARCIS (Netherlands)

    Peijzel, P.S.

    2004-01-01

    This thesis describes vacuum ultraviolet (VUV) spectroscopy of lanthanide ions. High-resolution emission and excitation spectra were recorded to investigate the VUV energy levels of lanthanide ions in fluoride and phosphate host lattices. A parameterized model for the calculation of the energy-level

  8. Cytosolic glutamine synthetase Gln1;2 is the main isozyme contributing to GS1 activity and can be up-regulated to relieve ammonium toxicity

    DEFF Research Database (Denmark)

    Guan, Miao; de Bang, Thomas Christian; Pedersen, Carsten

    2016-01-01

    of the high-affinity low-capacity isoform Gln-1;1 was reduced. The expression of Gln-1;3 did not respond to ammonium treatment while Gln-1;4 and Gln-1;5 isogenes in all cases were expressed at a very low level. Gln-2 was highly expressed in shoots but only at a very low level in roots. To investigate...

  9. Nuclear Level Density at High Spin and Excitation Energy

    Institute of Scientific and Technical Information of China (English)

    A.N. Behkami; Z. Kargar

    2001-01-01

    The intensive studies of equilibrium processes in heavy-ion reaction have produced a need for information on nuclear level densities at high energies and spins. The Fermi gas level density is often used in investigation of heavy-ion reaction studies. Some papers have claimed that nuclear level densities might deviate substantially from the Fermi gas predications at excitations related to heavy-ion reactions. The formulae of calculation of the nuclear level density based on the theory of superconductivity are presented, special attention is paid to the dependence of the level density on the angular momentum. The spin-dependent nuclear level density is evaluated using the pairing interaction. The resulting level density for an average spin of 52h is evaluated for 155Er and compared with experimental data. Excellent agreement between experiment and theory is obtained.``

  10. High level resistance to aminoglycosides in enterococci from Riyadh.

    Science.gov (United States)

    Al-Ballaa, S R; Qadri, S M; Al-Ballaa, S R; Kambal, A M; Saldin, H; Al-Qatary, K

    1994-07-01

    Enterococci with high level of aminoglycosides resistance are being reported from different parts of the world with increasing frequency. Treatment of infections caused by such isolates is associated with a high incidence of failure or relapse. This is attributed to the loss of the synergetic effect of aminoglycosides and cell wall active agents against isolates exhibiting this type of resistance. To determine the prevalence of enterococci with high level resistance to aminoglycosides in Riyadh, Saudi Arabia, 241 distinct clinical isolates were examined by disk diffusion method using high content aminoglycosides disks. Seventy-four isolates (30%) were resistant to one or more of the aminoglycosides tested. The most common pattern of resistance was that to streptomycin and kanamycin. Of the 241 isolates tested, 29 (12%) were resistant to high levels of gentamicin, 35 (15%) to tobramycin, 65 (27%) to kanamycin and 53 (22%) to streptomycin. The highest rate of resistance to a high level of gentamicin was found among enterococcal blood isolates (30%). Eighteen of the isolates were identified as Enterococcus faecium, 13 (72%) of these showed high level resistance to two or more of the aminoglycosides tested.

  11. Face Tracking with Low-level and High-level Information

    Institute of Scientific and Technical Information of China (English)

    XUDong; LIStan; LIUZhengkai

    2005-01-01

    Face Tracking is an important and difficult vision task. In this paper, the high-level frontal face detector information and the low-level color information are fused iteratively. With the multi-step fusion schemes, better face tracking performance is achieved, as demonstrated by the exhaustive experiments.

  12. 49 CFR 176.410 - Division 1.5 materials, ammonium nitrate and ammonium nitrate mixtures.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Division 1.5 materials, ammonium nitrate and ammonium nitrate mixtures. 176.410 Section 176.410 Transportation Other Regulations Relating to... nitrate and ammonium nitrate mixtures. (a) This section prescribes requirements to be observed...

  13. 33 CFR 126.28 - Ammonium nitrate, ammonium nitrate fertilizers, fertilizer mixtures, or nitro carbo nitrate...

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Ammonium nitrate, ammonium nitrate fertilizers, fertilizer mixtures, or nitro carbo nitrate; general provisions. 126.28 Section 126...) WATERFRONT FACILITIES HANDLING OF DANGEROUS CARGO AT WATERFRONT FACILITIES § 126.28 Ammonium...

  14. An overview of very high level software design methods

    Science.gov (United States)

    Asdjodi, Maryam; Hooper, James W.

    1988-01-01

    Very High Level design methods emphasize automatic transfer of requirements to formal design specifications, and/or may concentrate on automatic transformation of formal design specifications that include some semantic information of the system into machine executable form. Very high level design methods range from general domain independent methods to approaches implementable for specific applications or domains. Applying AI techniques, abstract programming methods, domain heuristics, software engineering tools, library-based programming and other methods different approaches for higher level software design are being developed. Though one finds that a given approach does not always fall exactly in any specific class, this paper provides a classification for very high level design methods including examples for each class. These methods are analyzed and compared based on their basic approaches, strengths and feasibility for future expansion toward automatic development of software systems.

  15. Does high serum uric acid level cause aspirin resistance?

    Science.gov (United States)

    Yildiz, Bekir S; Ozkan, Emel; Esin, Fatma; Alihanoglu, Yusuf I; Ozkan, Hayrettin; Bilgin, Murat; Kilic, Ismail D; Ergin, Ahmet; Kaftan, Havane A; Evrengul, Harun

    2016-06-01

    In patients with coronary artery disease (CAD), though aspirin inhibits platelet activation and reduces atherothrombotic complications, it does not always sufficiently inhibit platelet function, thereby causing a clinical situation known as aspirin resistance. As hyperuricemia activates platelet turnover, aspirin resistance may be specifically induced by increased serum uric acid (SUA) levels. In this study, we thus investigated the association between SUA level and aspirin resistance in patients with CAD. We analyzed 245 consecutive patients with stable angina pectoris (SAP) who in coronary angiography showed more than 50% occlusion in a major coronary artery. According to aspirin resistance, two groups were formed: the aspirin resistance group (Group 1) and the aspirin-sensitive group (Group 2). Compared with those of Group 2, patients with aspirin resistance exhibited significantly higher white blood cell counts, neutrophil counts, neutrophil-to-lymphocyte ratios, SUA levels, high-sensitivity C-reactive protein levels, and fasting blood glucose levels. After multivariate analysis, a high level of SUA emerged as an independent predictor of aspirin resistance. The receiver-operating characteristic analysis provided a cutoff value of 6.45 mg/dl for SUA to predict aspirin resistance with 79% sensitivity and 65% specificity. Hyperuricemia may cause aspirin resistance in patients with CAD and high SUA levels may indicate aspirin-resistant patients. Such levels should thus recommend avoiding heart attack and stroke by adjusting aspirin dosage.

  16. Overexpressing of OsAMT1-3, a High Affinity Ammonium Transporter Gene, Modifies Rice Growth and Carbon-Nitrogen Metabolic Status.

    Science.gov (United States)

    Bao, Aili; Liang, Zhijun; Zhao, Zhuqing; Cai, Hongmei

    2015-04-23

    AMT1-3 encodes the high affinity NH₄⁺ transporter in rice roots and is predominantly expressed under nitrogen starvation. In order to evaluate the effect of AMT1-3 gene on rice growth, nitrogen absorption and metabolism, we generated AMT1-3-overexpressing plants and analyzed the growth phenotype, yield, carbon and nitrogen metabolic status, and gene expression profiles. Although AMT1-3 mRNA accumulated in transgenic plants, these plants displayed significant decreases in growth when compared to the wild-type plants. The nitrogen uptake assay using a 15N tracer revealed poor nitrogen uptake ability in AMT1-3-overexpressing plants. We found significant decreases in AMT1-3-overexpressing plant leaf carbon and nitrogen content accompanied with a higher leaf C/N ratio. Significant changes in soluble proteins and carbohydrates were also observed in AMT1-3-overexpressing plants. In addition, metabolite profile analysis demonstrated significant changes in individual sugars, organic acids and free amino acids. Gene expression analysis revealed distinct expression patterns of genes that participate in carbon and nitrogen metabolism. Additionally, the correlation between the metabolites and gene expression patterns was consistent in AMT1-3-overexpressing plants under both low and high nitrogen growth conditions. Therefore, we hypothesized that the carbon and nitrogen metabolic imbalance caused by AMT1-3 overexpressing attributed to the poor growth and yield of transgenic plants.

  17. Overexpressing of OsAMT1-3, a High Affinity Ammonium Transporter Gene, Modifies Rice Growth and Carbon-Nitrogen Metabolic Status

    Directory of Open Access Journals (Sweden)

    Aili Bao

    2015-04-01

    Full Text Available AMT1-3 encodes the high affinity NH4+ transporter in rice roots and is predominantly expressed under nitrogen starvation. In order to evaluate the effect of AMT1-3 gene on rice growth, nitrogen absorption and metabolism, we generated AMT1-3-overexpressing plants and analyzed the growth phenotype, yield, carbon and nitrogen metabolic status, and gene expression profiles. Although AMT1-3 mRNA accumulated in transgenic plants, these plants displayed significant decreases in growth when compared to the wild-type plants. The nitrogen uptake assay using a 15N tracer revealed poor nitrogen uptake ability in AMT1-3-overexpressing plants. We found significant decreases in AMT1-3-overexpressing plant leaf carbon and nitrogen content accompanied with a higher leaf C/N ratio. Significant changes in soluble proteins and carbohydrates were also observed in AMT1-3-overexpressing plants. In addition, metabolite profile analysis demonstrated significant changes in individual sugars, organic acids and free amino acids. Gene expression analysis revealed distinct expression patterns of genes that participate in carbon and nitrogen metabolism. Additionally, the correlation between the metabolites and gene expression patterns was consistent in AMT1-3-overexpressing plants under both low and high nitrogen growth conditions. Therefore, we hypothesized that the carbon and nitrogen metabolic imbalance caused by AMT1-3 overexpressing attributed to the poor growth and yield of transgenic plants.

  18. Model-Based Feasibility Assessment of Membrane Biofilm Reactor to Achieve Simultaneous Ammonium, Dissolved Methane, and Sulfide Removal from Anaerobic Digestion Liquor

    Science.gov (United States)

    Chen, Xueming; Liu, Yiwen; Peng, Lai; Yuan, Zhiguo; Ni, Bing-Jie

    2016-04-01

    In this study, the membrane biofilm reactor (MBfR) is proposed to achieve simultaneous removal of ammonium, dissolved methane, and sulfide from main-stream and side-stream anaerobic digestion liquors. To avoid dissolved methane stripping, oxygen is introduced through gas-permeable membranes, which also from the substratum for the growth of a biofilm likely comprising ammonium oxidizing bacteria (AOB), anaerobic ammonium oxidation (Anammox) bacteria, denitrifying anaerobic methane oxidation (DAMO) microorganisms, aerobic methane oxidizing bacteria (MOB), and sulfur oxidizing bacteria (SOB). A mathematical model is developed and applied to assess the feasibility of such a system and the associated microbial community structure under different operational conditions. The simulation studies demonstrate the feasibility of achieving high-level (>97.0%), simultaneous removal of ammonium, dissolved methane, and sulfide in the MBfRs from both main-stream and side-stream anaerobic digestion liquors through adjusting the influent surface loading (or hydraulic retention time (HRT)) and the oxygen surface loading. The optimal HRT was found to be inversely proportional to the corresponding oxygen surface loading. Under the optimal operational conditions, AOB, DAMO bacteria, MOB, and SOB dominate the biofilm of the main-stream MBfR, while AOB, Anammox bacteria, DAMO bacteria, and SOB coexist in the side-stream MBfR to remove ammonium, dissolved methane, and sulfide simultaneously.

  19. Ammonium/methylammonium permeases of a Cyanobacterium. Identification and analysis of three nitrogen-regulated amt genes in synechocystis sp. PCC 6803.

    Science.gov (United States)

    Montesinos, M L; Muro-Pastor, A M; Herrero, A; Flores, E

    1998-11-20

    Ammonium is an important nitrogen source for many microorganisms and plants. Ammonium transporters whose activity can be probed with [14C]methylammonium have been described in several organisms including some cyanobacteria, and amt genes encoding ammonium/methylammonium permeases have been recently identified in yeast, Arabidopsis thaliana, and some bacteria. The unicellular cyanobacterium Synechocystis sp. PCC 6803 exhibited a [14C]methylammonium uptake activity that was inhibited by externally added ammonium. Three putative amt genes that are found in the recently published complete sequence of the chromosome of strain PCC 6803 were inactivated by insertion of antibiotic resistance-encoding gene-cassettes. The corresponding mutant strains were impaired in uptake of [14C]methylammonium. Open reading frame sll0108 (amt1) was responsible for a high affinity uptake activity (Ks for methylammonium, 2.7 microM), whereas open reading frames sll1017 (amt2) and sll0537 (amt3) made minor contributions to uptake at low substrate concentrations. Expression of the three amt genes was higher in nitrogen-starved cells than in cells incubated in the presence of a source of nitrogen (either ammonium or nitrate), but amt1 was expressed at higher levels than the other two amt genes. Transcription of amt1 was found to take place from a promoter bearing the structure of the cyanobacterial promoters activated by the nitrogen control transcription factor, NtcA.

  20. High-level trigger system for the LHC ALICE experiment

    Energy Technology Data Exchange (ETDEWEB)

    Bramm, R.; Helstrup, H.; Lien, J.; Lindenstruth, V.; Loizides, C.; Roehrich, D.; Skaali, B.; Steinbeck, T.; Stock, R.; Ullaland, K.; Vestboe, A. E-mail: vestbo@fi.uib.no; Wiebalck, A

    2003-04-21

    The central detectors of the ALICE experiment at LHC will produce a data size of up to 75 MB/event at an event rate {<=}200 Hz resulting in a data rate of {approx}15 GB/s. Online processing of the data is necessary in order to select interesting (sub)events ('High Level Trigger'), or to compress data efficiently by modeling techniques. Processing this data requires a massive parallel computing system (High Level Trigger System). The system will consist of a farm of clustered SMP-nodes based on off-the-shelf PCs connected with a high bandwidth low latency network.

  1. High-level trigger system for the LHC ALICE experiment

    CERN Document Server

    Bramm, R; Lien, J A; Lindenstruth, V; Loizides, C; Röhrich, D; Skaali, B; Steinbeck, T M; Stock, Reinhard; Ullaland, K; Vestbø, A S; Wiebalck, A

    2003-01-01

    The central detectors of the ALICE experiment at LHC will produce a data size of up to 75 MB/event at an event rate less than approximately equals 200 Hz resulting in a data rate of similar to 15 GB/s. Online processing of the data is necessary in order to select interesting (sub)events ("High Level Trigger"), or to compress data efficiently by modeling techniques. Processing this data requires a massive parallel computing system (High Level Trigger System). The system will consist of a farm of clustered SMP-nodes based on off- the-shelf PCs connected with a high bandwidth low latency network.

  2. High-level trigger system for the LHC ALICE experiment

    Science.gov (United States)

    Bramm, R.; Helstrup, H.; Lien, J.; Lindenstruth, V.; Loizides, C.; Röhrich, D.; Skaali, B.; Steinbeck, T.; Stock, R.; Ullaland, K.; Vestbø, A.; Wiebalck, A.; ALICE Colloboration

    2003-04-01

    The central detectors of the ALICE experiment at LHC will produce a data size of up to 75 MB/ event at an event rate ⩽200 Hz resulting in a data rate of ˜15 GB/ s. Online processing of the data is necessary in order to select interesting (sub)events ("High Level Trigger"), or to compress data efficiently by modeling techniques. Processing this data requires a massive parallel computing system (High Level Trigger System). The system will consist of a farm of clustered SMP-nodes based on off-the-shelf PCs connected with a high bandwidth low latency network.

  3. Model-based evaluation on the conversion ratio of ammonium to nitrite in a nitritation process for ammonium-rich wastewater treatment

    Institute of Scientific and Technical Information of China (English)

    LI Xiao-ming; YANG Qi; ZENG Guang-ming; A. Cornelius; K. H. Rosenwinkel; S. Kunst; D. Weichgrebe

    2004-01-01

    Modeling for nitritation process was discussed and analyzed quantlitatively for the factors that influence nitrite accumulation. The results indicated that pH, inorganic carbon source and Hydraulic Retention Time(HRT) as well as biomass concentration are the main factors that influenced the conversion ratio of ammonium to nitrite. A constant high pH can lead to a high nitritation rate and results in high conversion ratio on condition that free ammonia inhibition do not happen. In a CSTR system, without pH control, this conversion ratio can be monitored by pH variation in the reactor. The pH goes down far from the inlet level means a strongly nitrite accumulation. High concentration of alkalinity can promoted the conversion ratio by means of accelerating the nitritation rate through providing sufficient inorganic carbon source(carbon dioxide). When inorganic carbon source was depleted, the nitritation process stopped. HRT adjustment could be an efficient way to make the nitritation system run more flexible, which to some extent can meet the requirements of the fluctuant of inlet parameters such as ammonium concentration, pH, and temperature and so on. Biomass concentration is the key point, especially for a CSTR system in steady state, which was normally circumscribed by the characteristics of bacteria and may also affected by aeration mode and can be increased by prolonging the HRT on the condition of no nitrate accumulation when no recirculation available. The higher the biomass concentration is, the better the nitrite accumulation can be obtained.

  4. Efficient cellulose solvent: quaternary ammonium chlorides.

    Science.gov (United States)

    Kostag, Marc; Liebert, Tim; El Seoud, Omar A; Heinze, Thomas

    2013-10-01

    Pure quaternary tetraalkylammonium chlorides with one long alkyl chain dissolved in various organic solvents constitute a new class of cellulose solvents. The electrolytes are prepared in high yields and purity by Menshutkin quaternization, an inexpensive and easy synthesis route. The pure molten tetraalkylammonium chlorides dissolve up to 15 wt% of cellulose. Cosolvents, including N,N-dimethylacetamide (DMA), may be added in large excess, leading to a system of decreased viscosity. Contrary to the well-established solvent DMA/LiCl, cellulose dissolves in DMA/quaternary ammonium chlorides without any pretreatment. Thus, the use of the new solvent avoids some disadvantages of DMA/LiCl and ionic liquids, the most extensively employed solvents for homogeneous cellulose chemistry.

  5. Interactions between nitrate and ammonium in their uptake, allocation, assimilation, and signaling in plants.

    Science.gov (United States)

    Hachiya, Takushi; Sakakibara, Hitoshi

    2016-12-21

    Nitrogen (N) availability is a major factor determining plant growth and productivity. Plants acquire inorganic N from the soil, mainly in the form of nitrate and ammonium. To date, researchers have focused on these N sources, and demonstrated that plants exhibit elaborate responses at both physiological and morphological levels. Mixtures of nitrate and ammonium are beneficial in terms of plant growth, as compared to nitrate or ammonium alone, and therefore synergistic responses to both N sources are predicted at different steps ranging from acquisition to assimilation. In this review, we summarize interactions between nitrate and ammonium with respect to uptake, allocation, assimilation, and signaling. Given that cultivated land often contains both nitrate and ammonium, a better understanding of the synergism between these N sources should help to identify targets with the potential to improve crop productivity.

  6. Portable High Sensitivity and High Resolution Sensor to Determine Oxygen Purity Levels Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The objective of this Phase I STTR project is to develop a highly sensitive oxygen (O2) sensor, with high accuracy and precision, to determine purity levels of high...

  7. Highly efficient ablation of metastatic breast cancer using ammonium-tungsten-bronze nanocube as a novel 1064 nm-laser-driven photothermal agent.

    Science.gov (United States)

    Guo, Chongshen; Yu, Haijun; Feng, Bing; Gao, Weidong; Yan, Mei; Zhang, Zhiwen; Li, Yaping; Liu, Shaoqin

    2015-06-01

    Photothermal ablation (PTA) therapy has been viewed as an invasive option for cancer therapy with minimal deconstruction of healthy tissues. In this study, a potent candidate of (NH4)xWO3 nanocube was developed for PTA treatment of metastatic breast cancer in the second near-infrared (NIR) window. It was found that the as-synthesized (NH4)xWO3 nanocube had significant photoabsorption across the whole NIR window of 780-2500 nm and exhibited considerable photo-heat conversion efficiency. Moreover, the as-prepared (NH4)xWO3 nanocube displayed good biocompatibility and high cellular uptake efficiency through endocytosis pathway without nuclei entry. The PTA study employing 1064 nm laser in the second NIR window revealed that (NH4)xWO3 nanocubes induced significant cell necrosis and apoptosis by producing obviously hyperthermia effect inside cancer cells. Using an orthotopicly implanted breast tumor model, it demonstrated that the (NH4)xWO3 nanocube was a promising photothermal agent for effective ablation of solid tumors and suppressing their distant metastasis.

  8. Biodegradation of rocket propellant waste, ammonium perchlorate

    Science.gov (United States)

    Naqvi, S. M. Z.; Latif, A.

    1975-01-01

    The short term effects of ammonium perchlorate on selected organisms were studied. A long term experiment was also designed to assess the changes incurred by ammonium perchlorate on the nitrogen and chloride contents of soil within a period of 3 years. In addition, an attempt was made to produce methane gas from anaerobic fermentation of the aquatic weed, Alternanthera philoxeroides.

  9. Effect of high fluoride and high fat on serum lipid levels and oxidative stress in rabbits.

    Science.gov (United States)

    Sun, Liyan; Gao, Yanhui; Zhang, Wei; Liu, Hui; Sun, Dianjun

    2014-11-01

    The purpose of this study was to explore the effects of high fluoride and high fat on triglyceride (TG), total cholesterol (TC), high density lipoprotein cholesterol (HDL-C), low density lipoprotein cholesterol (LDL-C), total antioxidant capacity (T-AOC), lipid peroxide (LPO) and malondialdehyde (MDA) in rabbits. A factorial experimental design was used, with two factors (fluoride and fat) and three levels. Seventy-two male rabbits were randomly assigned into nine groups according to initial weight and serum lipid levels. The rabbits were fed with basic feed, moderate fat feed or high fat feed and drank tap water, fluoridated water at levels of 50 and 100mgfluorion/L freely. Biological materials were collected after 5 months, and serum lipid, T-AOC, LPO, and MDA levels were then measured. Using these data, the separate and interactive effects of high fluoride and high fat were analyzed. High fluoride and high fat both increased serum levels of TC, HDL-C and LDL-C significantly (Pfluoride and high fat (Pfluoride and high fat had different effects on TG levels: high fat significantly increased TG levels (Pfluoride had nothing to do with TG levels (P>0.05). High fat significantly elevated LPO and MDA levels and lowered T-AOC levels in serum (Pfluoride significantly increased LPO and MDA levels in serum (Pfluoride on these indexes. In summary, high fluoride and high fat increased serum TC and LDL-C levels individually and synergistically, and this would cause and aggravate hypercholesterolemia in rabbits. At the same time, high fluoride and high fat both made the accumulation of product of oxidative stress in experimental animals. Copyright © 2014 Elsevier B.V. All rights reserved.

  10. VHDL Specification Methodology from High-level Specification

    Directory of Open Access Journals (Sweden)

    M. Benmohammed

    2005-01-01

    Full Text Available Design complexity has been increasing exponentially this last decade. In order to cope with such an increase and to keep up designers' productivity, higher level specifications were required. Moreover new synthesis systems, starting with a high level specification, have been developed in order to automate and speed up processor design. This study presents a VHDL specification methodology aimed to extend structured design methodologies to the behavioral level. The goal is to develop VHDL modeling strategies in order to master the design and analysis of large and complex systems. Structured design methodologies are combined with a high-level synthesis system, a VHDL based behavioral synthesis tool, in order to allow hierarchical design and component re-use.

  11. 49 CFR 176.415 - Permit requirements for Division 1.5, ammonium nitrates, and certain ammonium nitrate fertilizers.

    Science.gov (United States)

    2010-10-01

    ... nitrates, and certain ammonium nitrate fertilizers. 176.415 Section 176.415 Transportation Other... requirements for Division 1.5, ammonium nitrates, and certain ammonium nitrate fertilizers. (a) Except as... Captain of the Port (COTP). (1) Ammonium nitrate UN1942, ammonium nitrate fertilizers containing more...

  12. Web Based Technologies to Support High Level Process Maturity

    Directory of Open Access Journals (Sweden)

    A. V. Sharmila

    2013-07-01

    Full Text Available This paper discusses the uses of Web based Technologies to support High Level Process Maturity in an organization. It also provides an overview of CMMI, focusing on the importance of centralized data storage and data access for sustaining high maturity levels of CMMI. Further, elaboration is made on the web based technology, stressing that change over to Web Based Application is extremely helpful to maintain the centralized data repository, to collect data for process capability baseline, and to track process performance management, with reduced maintenance effort and ease of data access. A case study analysis of advantages of adopting Web Based Technology is also narrated. Finally the paper concludes that the sustenance of High level Process maturity can be achieved by adopting web application technology.

  13. Theory and Methods for Supporting High Level Military Decisionmaking

    Science.gov (United States)

    2007-01-01

    Gompert, and Kugler, 1996; Davis, 2002a). The relationship between defense applications and finance is more metaphorical than mathematical. A...be summarized as the fractal problem: • • 62 Theory and Methods for Supporting High-Level Military Decisionmaking Describing objectives...strategies, tactics, and tasks is a fractal matter—i.e., the concepts apply and are needed at each level, whether that of the president, the theater commander

  14. Building high-level features using large scale unsupervised learning

    CERN Document Server

    Le, Quoc V; Devin, Matthieu; Corrado, Greg; Chen, Kai; Ranzato, Marc'Aurelio; Dean, Jeff; Ng, Andrew Y

    2011-01-01

    We consider the problem of building detectors for high-level concepts using only unsupervised feature learning. For example, we would like to understand if it is possible to learn a face detector using only unlabeled images downloaded from the internet. To answer this question, we trained a simple feature learning algorithm on a large dataset of images (10 million images, each image is 200x200). The simulation is performed on a cluster of 1000 machines with fast network hardware for one week. Extensive experimental results reveal surprising evidence that such high-level concepts can indeed be learned using only unlabeled data and a simple learning algorithm.

  15. Sterilization, high-level disinfection, and environmental cleaning.

    Science.gov (United States)

    Rutala, William A; Weber, David J

    2011-03-01

    Failure to perform proper disinfection and sterilization of medical devices may lead to introduction of pathogens, resulting in infection. New techniques have been developed for achieving high-level disinfection and adequate environmental cleanliness. This article examines new technologies for sterilization and high-level disinfection of critical and semicritical items, respectively, and because semicritical items carry the greatest risk of infection, the authors discuss reprocessing semicritical items such as endoscopes and automated endoscope reprocessors, endocavitary probes, prostate biopsy probes, tonometers, laryngoscopes, and infrared coagulation devices. In addition, current issues and practices associated with environmental cleaning are reviewed.

  16. High Level Waste (HLW) Feed Process Control Strategy

    Energy Technology Data Exchange (ETDEWEB)

    STAEHR, T.W.

    2000-06-14

    The primary purpose of this document is to describe the overall process control strategy for monitoring and controlling the functions associated with the Phase 1B high-level waste feed delivery. This document provides the basis for process monitoring and control functions and requirements needed throughput the double-shell tank system during Phase 1 high-level waste feed delivery. This document is intended to be used by (1) the developers of the future Process Control Plan and (2) the developers of the monitoring and control system.

  17. Final report on cermet high-level waste forms

    Energy Technology Data Exchange (ETDEWEB)

    Kobisk, E.H.; Quinby, T.C.; Aaron, W.S.

    1981-08-01

    Cermets are being developed as an alternate method for the fixation of defense and commercial high level radioactive waste in a terminal disposal form. Following initial feasibility assessments of this waste form, consisting of ceramic particles dispersed in an iron-nickel base alloy, significantly improved processing methods were developed. The characterization of cermets has continued through property determinations on samples prepared by various methods from a variety of simulated and actual high-level wastes. This report describes the status of development of the cermet waste form as it has evolved since 1977. 6 tables, 18 figures.

  18. Determination of urine oxalate level in rats with renal calcium oxalate calculus by high-performance liquid chromatography.

    Science.gov (United States)

    Cao, Qiu-shi; Ba, Yuan-ming; Luo, Jun-hua; Dai, Qi

    2015-02-01

    To establish a method of high-performance liquid chromatography (HPLC) for determining the urine oxalate levle in rats with renal calcium oxalate calculus. Totally 24 SPF Wistar healthy male rats were randomly divided into control group(n=12)and ethylene glycol (EG) group (n=12). Rats in EG group were administered intragastrically with 2% ammonium chloride (AC)2 ml/rat per day+1% ethylene glycol (EG), along with free access to drinking water.The control group was fed with deionized water, along with the intragastric administration of normal saline (1 ml per day). Twenty-eight days after modelling, the 24-hour urine samples were collected, and the urine oxalic acid levels were determined using HPLC and the results were compared with those of catalytic spectrophotometry using oxidation of methyl. During the HPLC, the samples were separated on Aglient 5TC-C18 (250×4.6 mm,5 Μm), eluted with mixture of methanol (0.1 mol/L) and ammonium acetate (15:85) at 1.2 ml/min, and detected at 314 nm, with the column temperature being 20 ℃. The standard curves of high and low concentrations of oxalic acid were y=5909.1x+378730, R² =0.9984 and y=7810.5x-16635, R² =0.9967,respectively. The lowest detectable concentration in this method was 5 Μg/ml. The linear high concentration range of oxalate stood at 62.50-2000.00 Μg/ml, and the linear low concentration range of oxalate stood at 6.25-100.00 Μg/ml. Its average recovery was 95.1%, and its within-day and day-to-day precisions were 3.4%-10.8% and 3.8%-9.4%. Both HPLC and catalytic spectrophotometry showed significantly higher urinary oxalic acid concentration and 24 h urine oxalate level in EG group compared with the control group [urinary oxalic acid concentration: (736.35 ± 254.52) Μg/ml vs.(51.56 ± 36.34) Μg/ml,(687.35 ± 234.53) Μg/ml vs.(50.24 ± 42.34) Μg/ml;24 h urine oxalate level: (11.23 ± 4.12)mg vs.(0.87 ± 0.45)mg,(9.89 ± 3.55)mg vs. (0.77 ± 0.65)mg; all P0.05). HPLC is a simple, rapid, and precise method

  19. Photo-Fenton-like degradation of azo dye methyl orange using synthetic ammonium and hydronium jarosite

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Zhihui [Department of Chemistry, College of Science, Nanjing Agricultural University, Nanjing 210095 (China); Liang, Jianru [Department of Environmental Engineering, College of Resources and Environmental Sciences, Nanjing Agricultural University, Nanjing 210095 (China); Zhou, Lixiang, E-mail: lxzhou@njau.edu.cn [Department of Environmental Engineering, College of Resources and Environmental Sciences, Nanjing Agricultural University, Nanjing 210095 (China)

    2013-01-05

    Highlights: Black-Right-Pointing-Pointer Hydronium and ammonium jarosite could catalyze the oxidation of methyl orange in photo-Fenton-like process. Black-Right-Pointing-Pointer The oxidation process is essentially heterogeneous, not homogeneous. Black-Right-Pointing-Pointer Hydronium jarosite has stronger reactivity than ammonium jarosite. - Abstract: Ammonium and hydronium jarosite were prepared by hydrothermal method with urea as the homogeneous precipitant. X-ray diffraction, field-emission scanning electron microscope, X-ray photoelectron spectrum, UV-vis spectra and fourier transform infrared spectrum were used to characterize the resulting products. The photodegradation efficiency of the prepared ammonium and hydronium jarosite was studied in a photo-Fenton-like process using methyl orange (MO) as target pollutant. The photocatalytic degradation of MO over synthetic ammonium and hydronium jarosite under various conditions, such as catalysts loading, H{sub 2}O{sub 2} concentration and initial pH, has been investigated. Results show that ammonium and hydronium jarosite have satisfactory photocatalysis effect in degradation of MO azo dye, and that the reactivity of hydronium jarosite toward the mineralization of MO was higher than that of ammonium jarosite. The novel ammonium and hydronium jarosite catalysts would be important for industrial applications due to their high photoactivity, little iron leaching and low cost.

  20. The nucleation kinetics of ammonium metavanadate precipitated by ammonium chloride

    Science.gov (United States)

    Du, Guangchao; Sun, Zhaohui; Xian, Yong; Jing, Han; Chen, Haijun; Yin, Danfeng

    2016-05-01

    The nucleation kinetics of ammonium metavanadate (NH4VO3) was investigated under conditions of the simulated process for precipitation of NH4VO3 from the vanadium-containing solution. Induction periods for the nucleation of NH4VO3 were experimentally determined as a function of supersaturation at temperatures from 30 to 45 °C. Using the classical nucleation theory, the interfacial tension between NH4VO3 and supersaturated solution, the nucleation rate and critical radius of nucleus for the homogeneous nucleation of NH4VO3 were estimated. With temperature increasing, the calculated interfacial tension gradually decreased from 29.78 mJ/m2 at 30 °C to 23.66 mJ/m2 at 45 °C. The nucleation rate was found to proportionally increase but the critical radius of nucleus exponentially decreased, with increase in supersaturation ratio at a constant temperature. The activation energy for NH4VO3 nucleation was obtained from the relationship between temperature and induction period, ranging from 79.17 kJ/mol at S=25 to 115.50 kJ/mol at S=15. FT-IR and Raman spectrum indicated that the crystals obtained in the precipitation process were NH4VO3.

  1. Transmission Level High Temperature Superconducting Fault Current Limiter

    Energy Technology Data Exchange (ETDEWEB)

    Stewart, Gary [SuperPower, Inc., Schenectady, NY (United States)

    2016-10-05

    The primary objective of this project was to demonstrate the feasibility and reliability of utilizing high temperature superconducting (HTS) materials in a Transmission Level Superconducting Fault Current Limiter (SFCL) application. During the project, the type of high temperature superconducting material used evolved from 1st generation (1G) BSCCO-2212 melt cast bulk high temperature superconductors to 2nd generation (2G) YBCO based high temperature superconducting tape. The SFCL employed SuperPower's “Matrix” technology that offers modular features to enable scale up to transmission voltage levels. The SFCL consists of individual modules that contain elements and parallel inductors that assist in carrying the current during the fault. A number of these modules are arranged in an m x n array to form the current limiting matrix.

  2. Transmission Level High Temperature Superconducting Fault Current Limiter

    Energy Technology Data Exchange (ETDEWEB)

    Stewart, Gary [SuperPower, Inc., Schenectady, NY (United States)

    2016-10-05

    The primary objective of this project was to demonstrate the feasibility and reliability of utilizing high-temperature superconducting (HTS) materials in a Transmission Level Superconducting Fault Current Limiter (SFCL) application. During the project, the type of high-temperature superconducting material used evolved from 1st generation (1G) BSCCO-2212 melt cast bulk high-temperature superconductors to 2nd generation (2G) YBCO-based high-temperature superconducting tape. The SFCL employed SuperPower's “Matrix” technology, that offers modular features to enable scale up to transmission voltage levels. The SFCL consists of individual modules that contain elements and parallel inductors that assist in carrying the current during the fault. A number of these modules are arranged in an m x n array to form the current-limiting matrix.

  3. Online pattern recognition for the ALICE high level trigger

    CERN Document Server

    Bramm, R; Lien, J A; Lindenstruth, V; Loizides, C; Röhrich, D; Skaali, B; Steinbeck, T M; Stock, Reinhard; Ullaland, K; Vestbø, A S; Wiebalck, A

    2003-01-01

    The ALICE High Level Trigger system needs to reconstruct events online at high data rates. Focusing on the Time Projection Chamber we present two pattern recognition methods under investigation: the sequential approach (cluster finding, track follower) and the iterative approach (Hough Transform, cluster assignment, re-fitting). The implementation of the former in hardware indicates that we can reach the designed inspection rate for p-p collisions of 1 kHz with 98% efficiency.

  4. Online pattern recognition for the ALICE high level trigger

    Energy Technology Data Exchange (ETDEWEB)

    Bramm, R.; Helstrup, H.; Lien, J.; Lindenstruth, V.; Loizides, C. E-mail: loizides@ikf.uni-frankfurt.de; Rohrich, D.; Skaali, B.; Steinbeck, T.; Stock, R.; Ullaland, K.; Vestboe, A.; Wiebalck, A

    2003-04-21

    The ALICE High Level Trigger system needs to reconstruct events online at high data rates. Focusing on the Time Projection Chamber we present two pattern recognition methods under investigation: the sequential approach (cluster finding, track follower) and the iterative approach (Hough Transform, cluster assignment, re-fitting). The implementation of the former in hardware indicates that we can reach the designed inspection rate for p-p collisions of 1 kHz with 98% efficiency.

  5. Use of zeolitized coal fly ash in the simultaneous removal of ammonium and phosphate from aqueous solution

    Institute of Scientific and Technical Information of China (English)

    WU Deyi; HU Zhanbo; WANG Xinze; HE Shengbing; KONG Hainan

    2007-01-01

    Discharge of wastewater containing nitrogen and phosphate can cause cutrophication.Therefore,the development of an efficient material for the immobilization of the nutrients is important.In this study,a low calcium fly ash and high calcium fly ash were converted into zeolite using the hydrothermal method.The removal of ammonium and phosphate that coexist in aqueous solution by the synthesized zeolites were studied.The results showed that zeolitized fly ash could efficiently eliminate ammonium and phosphate at the same time.Saturation of zeolite with Ca2+ rather than Na+ favored the removal of both ammonium and Phosphate because the cation exchange reaction by the NH4+ resulted in the release of Ca2+ into the solution and precipitation of Ca2+ with POd43- followed.An increase in the temperature elevated the immobilization of phosphate whereas it abated the removal of ammonium.Nearly 60% removal efficiency for ammonium was achieved in the neutral pH range from 5.5 to 10.5.while the increase or decrease in pH out of the neutral range lowered the adsorption.In contrast,the removal of phosphate approached 100% at a pH lower than 5.0 or higher than 9.0,and less phosphate was immobilized at neutral pH.However,there was still a narrow pH range from 9.0 to 10.5 favoring the removal of both ammonium and phosphate.It was concluded that the removal of ammonium was caused by cation exchange;the contribution Of NH3 volatilization to immobilization at alkaline conditions(up to pH level of 11.4)was limited.with respect to phosphate immobilization,the mechanism was mainly the formation of precipitate as Ca3(PO4)2 within the basic pH range or as FePO4 and AlPO4 within acidic pH range.

  6. Translation of a High-Level Temporal Model into Lower Level Models: Impact of Modelling at Different Description Levels

    DEFF Research Database (Denmark)

    Kraft, Peter; Sørensen, Jens Otto

    2001-01-01

    the existences in time can be mapped precisely and consistently securing a consistent handling of the temporal properties. We translate the high level temporal model into an entity-relationship model, with the information in a two-dimensional graph, and finally we look at the translations into relational...

  7. Treating leachate mixture with anaerobic ammonium oxidation technology

    Institute of Scientific and Technical Information of China (English)

    ZHANG Hong-guo; ZHOU Shao-qi

    2006-01-01

    Large amounts of ammonium and a low content of biodegradable chemical oxygen demand(COD) are contained in leachate from aged landfills, together with the effluent containing high concentration of nitric nitrogen after biochemical treatment.Treatment effect of anaerobic ammonium oxidation (anammox) process on the mixture of the leachate and its biochemical effluent was investigated. The results show that the average removal efficiencies of ammonium, nitric nitrogen and total nitrogen are 87.51%,74.95% and 79.59%, respectively, corresponding to the average ratio of removed nitric nitrogen to ammonium, i.e. 1.14 during the steady phase of anammox activity. The mean removal efficiency of COD is only 24.01% during the experimental period. The demand of total phosphorous for the anammox process is unobvious. Especially, the alkalinity and pH value of the effluent are close to those of the influent during the steady phase of anammox activity. In addition, it is demonstrated that the status of the anammox bioreactor can be indicated by the alkalinity and pH value during the course of the experiment. The anammox bioreactor has shown potential for nitrogen removal in the leachate mixture. However, COD and total phosphorous in the leachate mixture need further treatment for removal efficiencies of COD and total phosphorous are not good in the anammox bioreactor.

  8. Nitrate, Nitrite, and Ammonium Variability in Drinking Water Distribution Systems.

    Science.gov (United States)

    Schullehner, Jörg; Stayner, Leslie; Hansen, Birgitte

    2017-03-09

    Accurate assessments of exposure to nitrate in drinking water is a crucial part of epidemiological studies investigating long-term adverse human health effects. However, since drinking water nitrate measurements are usually collected for regulatory purposes, assumptions on (1) the intra-distribution system variability and (2) short-term (seasonal) concentration variability have to be made. We assess concentration variability in the distribution system of nitrate, nitrite, and ammonium, and seasonal variability in all Danish public waterworks from 2007 to 2016. Nitrate concentrations at the exit of the waterworks are highly correlated with nitrate concentrations within the distribution net or at the consumers' taps, while nitrite and ammonium concentrations are generally lower within the net compared with the exit of the waterworks due to nitrification. However, nitrification of nitrite and ammonium in the distribution systems only results in a relatively small increase in nitrate concentrations. No seasonal variation for nitrate, nitrite, or ammonium was observed. We conclude that nitrate measurements taken at the exit of the waterworks are suitable to calculate exposures for all consumers connected to that waterworks and that sampling frequencies in the national monitoring programme are sufficient to describe temporal variations in longitudinal studies.

  9. High-Level Development of Multiserver Online Games

    Directory of Open Access Journals (Sweden)

    Frank Glinka

    2008-01-01

    Full Text Available Multiplayer online games with support for high user numbers must provide mechanisms to support an increasing amount of players by using additional resources. This paper provides a comprehensive analysis of the practically proven multiserver distribution mechanisms, zoning, instancing, and replication, and the tasks for the game developer implied by them. We propose a novel, high-level development approach which integrates the three distribution mechanisms seamlessly in today's online games. As a possible base for this high-level approach, we describe the real-time framework (RTF middleware system which liberates the developer from low-level tasks and allows him to stay at high level of design abstraction. We explain how RTF supports the implementation of single-server online games and how RTF allows to incorporate the three multiserver distribution mechanisms during the development process. Finally, we describe briefly how RTF provides manageability and maintenance functionality for online games in a grid context with dynamic resource allocation scenarios.

  10. Typewriter Modifications for Persons Who Are High-Level Quadriplegics.

    Science.gov (United States)

    O'Reagan, James R.; And Others

    Standard, common electric typewriters are not completely suited to the needs of a high-level quadriplegic typing with a mouthstick. Experiences show that for complete control of a typewriter a mouthstick user needs the combined features of one-button correction, electric forward and reverse indexing, and easy character viewing. To modify a…

  11. Site suitability criteria for solidified high level waste repositories

    Energy Technology Data Exchange (ETDEWEB)

    Heckman, R.A.; Holdsworth, T.; Towse, D.F.

    1979-03-07

    Activities devoted to development of regulations, criteria, and standards for storage of solidified high-level radioactive wastes are reported. The work is summarized in sections on site suitability regulations, risk calculations, geological models, aquifer models, human usage model, climatology model, and repository characteristics. Proposed additional analytical work is also summarized. (JRD)

  12. High-Level Overview of Data Needs for RE Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Lopez, Anthony

    2016-12-22

    This presentation provides a high level overview of analysis topics and associated data needs. Types of renewable energy analysis are grouped into two buckets: First, analysis for renewable energy potential, and second, analysis for other goals. Data requirements are similar but and they build upon one another.

  13. Reachability Trees for High-level Petri Nets

    DEFF Research Database (Denmark)

    Jensen, Kurt; Jensen, Arne M.; Jepsen, Leif Obel;

    1986-01-01

    the necessary analysis methods. In other papers it is shown how to generalize the concept of place- and transition invariants from place/transition nets to high-level Petri nets. Our present paper contributes to this with a generalization of reachability trees, which is one of the other important analysis...

  14. High-level manpower movement and Japan's foreign aid.

    Science.gov (United States)

    Furuya, K

    1992-01-01

    "Japan's technical assistance programs to Asian countries are summarized. Movements of high-level manpower accompanying direct foreign investments by private enterprise are also reviewed. Proposals for increased human resources development include education and training of foreigners in Japan as well as the training of Japanese aid experts and the development of networks for information exchange."

  15. High level cognitive information processing in neural networks

    Science.gov (United States)

    Barnden, John A.; Fields, Christopher A.

    1992-01-01

    Two related research efforts were addressed: (1) high-level connectionist cognitive modeling; and (2) local neural circuit modeling. The goals of the first effort were to develop connectionist models of high-level cognitive processes such as problem solving or natural language understanding, and to understand the computational requirements of such models. The goals of the second effort were to develop biologically-realistic model of local neural circuits, and to understand the computational behavior of such models. In keeping with the nature of NASA's Innovative Research Program, all the work conducted under the grant was highly innovative. For instance, the following ideas, all summarized, are contributions to the study of connectionist/neural networks: (1) the temporal-winner-take-all, relative-position encoding, and pattern-similarity association techniques; (2) the importation of logical combinators into connection; (3) the use of analogy-based reasoning as a bridge across the gap between the traditional symbolic paradigm and the connectionist paradigm; and (4) the application of connectionism to the domain of belief representation/reasoning. The work on local neural circuit modeling also departs significantly from the work of related researchers. In particular, its concentration on low-level neural phenomena that could support high-level cognitive processing is unusual within the area of biological local circuit modeling, and also serves to expand the horizons of the artificial neural net field.

  16. High-level expression, purification, polyclonal antibody preparation ...

    African Journals Online (AJOL)

    user

    2011-02-14

    Feb 14, 2011 ... Full Length Research Paper. High-level expression ... resistance severely compromises effective therapeutic options. ... In the present study, we first report the expression of the oprD ... databases of National Center for Biotechnology Information (NCBI) ..... assembly of the head of bacteriophage T4. Nature.

  17. Murine erythrocytes contain high levels of lysophospholipase activity

    NARCIS (Netherlands)

    Kamp, J.A.F. op den; Roelofsen, B.; Sanderink, G.; Middelkoop, E.; Hamer, R.

    1984-01-01

    Murine erythrocytes were found to be unique in the high levels of lysophospholipase activity in the cytosol of these cells. The specific activity of the enzyme in the cytosol of the murine cells is 10-times higher than in the cytosol of rabbit erythrocytes and approximately three orders of magnitude

  18. Detection of high risk campylobacteriosis clusters at three geographic levels

    Directory of Open Access Journals (Sweden)

    Jennifer Weisent

    2011-11-01

    Full Text Available Campylobacteriosis is a leading cause of bacterial gastroenteritis in the United States and many other developed countries. Understanding the spatial distribution of this disease and identifying high-risk areas is vital to focus resources for prevention and control measures. In addition, determining the appropriate scale for geographical analysis of surveillance data is an area of concern to epidemiologists and public health officials. The purpose of this study was to (i compare standardized risk estimates for campylobacteriosis in Tennessee over three distinct geographical scales (census tract, zip code and county subdivision, and (ii identify and investigate high-risk spatial clustering of campylobacteriosis at the three geographical scales to determine if clustering is scale dependent. Significant high risk clusters (P <0.05 were detected at all three spatial scales. There were overlaps in regions of high-risk and clusters at all three geographic levels. At the census tract level, spatial analysis identified smaller clusters of finer resolution and detected more clusters than the other two levels. However, data aggregation at zip code or county subdivision yielded similar findings. The importance of this line of research is to create a framework whereby economically efficient disease control strategies become more attainable through improved geographical precision and risk detection. Accurate identification of disease clusters for campylobacteriosis can enable public health personnel to focus scarce resources towards prevention and control programmes on the most at-risk populations. Consistent results at multiple spatial levels highlight the robustness of the geospatial techniques utilized in this study. Furthermore, analyses at the zip code and county subdivision levels can be useful when address level information (finer resolution data are not available. These procedures may also be used to help identify regionally specific risk factors for

  19. Analysis of nine food additives in red wine by ion-suppression reversed-phase high-performance liquid chromatography using trifluoroacetic acid and ammonium acetate as ion-suppressors.

    Science.gov (United States)

    Zhao, Yong-Gang; Chen, Xiao-Hong; Yao, Shan-Shan; Pan, Sheng-Dong; Li, Xiao-Ping; Jin, Mi-Cong

    2012-01-01

    A reversed-phase high-performance liquid chromatography (RP-HPLC) method was developed for the simultaneous determination of nine food additives, i.e., acesulfame, saccharin, caffeine, aspartame, benzoic acid, sorbic acid, stevioside, dehydroacetic acid and neotame in red wine. The effects of ion-suppressors, i.e., trifluoroacetic acid (TFA) and ammonium acetate (AmAc) on retention behavior of nine food additives in RP-HPLC separation were discussed in detail. The relationships between retention factors of solutes and volume percent of ion-suppressors in the mobile-phase systems of acetonitrile-TFA aqueous solution and acetonitrile-TFA-AmAc aqueous solution were quantitatively established, respectively. The results showed that the ion suppressors had not only an ion suppression effect, but also an organic modification effect on the acidic analytes. The baseline separation of nine food additives was completed by a gradient elution with acetonitrile-TFA(0.01%, v/v)-AmAc(2.5 mmol L(-1)) aqueous solution as the mobile phase. The recoveries were between 80.2 - 99.5% for all analytes with RSDs in the range of 1.5 - 8.9%. The linearities were in the range of 0.2 - 100.0 mg L(-1) with determination coefficients (r(2)) higher than 0.9991 for all analytes. The limits of quantification (LOQs) were between 0.53 - 0.99 mg L(-1). The applicability of the proposed method to detect and quantify food additives has been demonstrated in the analysis of 30 real samples.

  20. Ammonium polyphosphate improving physicochemical properties of rice straw-high density polyethylene composites%聚磷酸铵改善稻秸-高密度聚乙烯复合材料的理化性能

    Institute of Scientific and Technical Information of China (English)

    潘明珠; 梅长彤; 李国臣; 杜俊

    2014-01-01

    In recent years, plant fiber reinforced thermoplastic composites have been widely used as interior automotive panels, garbage pails, crates, and garden equipment due to their excellent durability, dimensional stability, high rigidity, and relatively low density. However, its poor fire resistance often limits its expansion into the residential construction industry and development of applications for the furniture industry. In order to improve the flame retardancy of the reinforced composites, fire retardant agents, such as halogen/nitrogen-containing substances, metal hydroxides, and phosphorus/silicon compounds, have been introduced. While there are environmental impact concerns, the most commonly used flame retardant additive is ammonium polyphosphate (APP). Recently, the synergistic effect between nano-SiO2 and ammonium polyphosphate (APP) in polymer and composites has been extensively investigated, and study has showed that the novel nano-SiO2/APP flame retardant could promote char formation, and improve the thermal stability of the char layer formed during combustion. China has been an important agricultural nation with 300 million tons of rice production annually. Using rice straw as a substitute feedstock material of wood fiber could be helpful for conserving valuable wood resources, protecting the environmental and contributing to sustainable development. Rice straw consists of cellulose, hemicellulose, lignin, silicon and pectin. Silicon, which is widely distributed in the surface of rice straw through biomineralization, could be also used as a synergistic agent of APP. In this paper, rice straw-high density polyethylene composites (RPC) with ammonium polyphosphate (APP, 0, 8%, 10%, and 12%) were prepared to investigate the effects on the thermal properties, flame retardancy, and mechanical properties of RPC using thermogravimetric analysis (TG), cone calorimentry analysis (Cone) and mechanical measurements. The mechanism of flame retardancy are also

  1. Ammonium sulfate preparation from phosphogypsum waste

    Directory of Open Access Journals (Sweden)

    Abdel-Hakim T. Kandil

    2017-01-01

    Full Text Available The Egyptian phosphogypsum waste is treated using sulfuric acid prior the ammonium sulfate production. The relevant factors that would affect the removal efficiencies of some impurities are studied. The optimum conditions of the treatment are 8 M sulfuric acid solution and 1/4 solid/liquid ratio for 30 min contact time at 80 °C. Moreover, the optimum conditions of the ammonium sulfate preparation are 10 g of the suspended impure or purified phosphogypsum in 40 ml of 3% ammonium sulfate solution (as initiator, 1/4 solid/liquid ratio at pH7 at an addition of an excess ammonium carbonate, and 150 rpm stirring speed for 4.0 h contact time at 55 °C as well as the 5 mg of barium chloride is added to remove the radium in the ammonium sulfate product. Finally, the ammonium sulfate is crystallized and the chemical analysis of the product shows 20% nitrogen and 23.6% sulfur. Therefore, the purity of the obtained ammonium sulfate is 95% from the purified phosphogypsum.

  2. Substrate specificity of Rhbg: ammonium and methyl ammonium transport.

    Science.gov (United States)

    Nakhoul, Nazih L; Abdulnour-Nakhoul, Solange M; Boulpaep, Emile L; Rabon, Edd; Schmidt, Eric; Hamm, L Lee

    2010-09-01

    Rhbg is a nonerythroid membrane glycoprotein belonging to the Rh antigen family. In the kidney, Rhbg is expressed at the basolateral membrane of intercalated cells of the distal nephron and is involved in NH4+ transport. We investigated the substrate specificity of Rhbg by comparing transport of NH3/NH4+ with that of methyl amine (hydrochloride) (MA/MA+), often used to replace NH3/NH4+, in oocytes expressing Rhbg. Methyl amine (HCl) in solution exists as neutral methyl amine (MA) in equilibrium with the protonated methyl ammonium (MA+). To assess transport, we used ion-selective microelectrodes and voltage-clamp experiments to measure NH3/NH4+- and MA/MA+-induced intracellular pH (pH(i)) changes and whole cell currents. Our data showed that in Rhbg oocytes, NH3/NH4+ caused an inward current and decrease in pH(i) consistent with electrogenic NH4+ transport. These changes were significantly larger than in H2O-injected oocytes. The NH3/NH4+-induced current was not inhibited in the presence of barium or in the absence of Na+. In Rhbg oocytes, MA/MA+ caused an inward current but an increase (rather than a decrease) in pH(i). MA/MA+ did not cause any changes in H2O-injected oocytes. The MA/MA+-induced current and pH(i) increase were saturated at higher concentrations of MA/MA+. Amiloride inhibited MA/MA+-induced current and the increase in pH(i) in oocytes expressing Rhbg but had no effect on control oocytes. These results indicate that MA/MA+ is transported by Rhbg but differently than NH3/NH4+. The protonated MA+ is likely a direct substrate whose transport resembles that of NH4+. Transport of electroneutral MA is also enhanced by expression of Rhbg.

  3. Ammonium tolerance in the cyanobacterium Synechocystis sp. strain PCC 6803 and the role of the psbA multigene family.

    Science.gov (United States)

    Dai, Guo-Zheng; Qiu, Bao-Sheng; Forchhammer, Karl

    2014-04-01

    Ammonium is one of the major nutrients for plants, and a ubiquitous intermediate in plant metabolism, but it is also known to be toxic to many organisms, in particular to plants and oxygenic photosynthetic microorganisms. Although previous studies revealed a link between ammonium toxicity and photodamage in cyanobacteria under in vivo conditions, ammonium-induced photodamage of photosystem II (PSII) has not yet been investigated with isolated thylakoid membranes. We show here that ammonium directly accelerated photodamage of PSII in Synechocystis sp. strain PCC6803, rather than affecting the repair of photodamaged PSII. Using isolated thylakoid membranes, it could be demonstrated that ammonium-induced photodamage of PSII primarily occurred at the oxygen evolution complex, which has a known binding site for ammonium. Wild-type Synechocystis PCC6803 cells can tolerate relatively high concentrations of ammonium because of efficient PSII repair. Ammonium tolerance requires all three psbA genes since mutants of any of the three single psbA genes are more sensitive to ammonium than wild-type cells. Even the poorly expressed psbA1 gene, whose expression was studied in some detail, plays a detectable role in ammonium tolerance. © 2013 John Wiley & Sons Ltd.

  4. Lumbar disc herniation at high levels : MRI and clinical findings

    Energy Technology Data Exchange (ETDEWEB)

    Paek, Chung Ho; Kwon, Soon Tae; Lee, Jun Kyu; Ahn, Jae Sung; Lee, Hwan Do; Chung, Yon Su; Jeong, Ki Ho; Cho, Jun Sik [Chungnam National Univ. College of Medicine, Taejon (Korea, Republic of)

    1999-04-01

    To assess the frequency, location, associated MR findings, and clinical symptoms of the high level lumbar disc herniation(HLDH). A total of 1076 patients with lunbar disc herniation were retrospectively reviewed. MR images of 41 of these with HLDH(T12-L1, L1-2, L2-3) were analysed in terms of frequency, location, and associated MR findings, and correlated with clinical symptoms of HLDH. The prevalence of HLDH was 3.8%(41/1076). HLDH was located at T12-L1 level in four patients(10%), at L1-2 level in 14(34%), at L2-3 level in 21(51%), and at both L1-2 and L2-3 levels in two. The age of patients ranged from 20 to 72 years (mean, 44), and there were 26 men and 16 women. In 11(27%), whose mean age was 32 years, isolated disc herniation was limited to these high lumbar segments. The remaining 30 patients had HLDH associated with variable involvement of the lower lumbar segments. Associated lesions were as follow : lower level disc herniation(14 patients, 34%); apophyseal ring fracture(8 patients, 19%); Schmorl's node and spondylolisthesis (each 6 patients, each 14%); spondylolysis(3 patients, 7%); and retrolisthesis(2 patients, 5%). In 20 patients(49%) with HLDH(n=41), there was a previous history of trauma. Patients with HLDH showed a relatively high incidence of associated coexisting abnormalities such as lower lumbar disc herniation, apophyseal ring fracture, Schmorl's node, spondylolysis, and retrolisthesis. In about half of all patients with HLDH there was a previous history of trauma. The mean age of patients with isolated HLDH was lower; clinical symptoms of the condition were relatively nonspecific and their incidence was low.

  5. High-Level Information Fusion Management and Systems Design

    CERN Document Server

    Blasch, Erik; Lambert, Dale

    2012-01-01

    High-level information fusion is the ability of a fusion system to capture awareness and complex relations, reason over past and future events, utilize direct sensing exploitations and tacit reports, and discern the usefulness and intention of results to meet system-level goals. This authoritative book serves a practical reference for developers, designers, and users of data fusion services that must relate the most recent theory to real-world applications. This unique volume provides alternative methods to represent and model various situations and describes design component implementations o

  6. Design and Prototyping of the ATLAS High Level Trigger

    Institute of Scientific and Technical Information of China (English)

    J.A.C.Bogaerts

    2001-01-01

    This paper outlines the desgn and prototyping of the ATLAS High Level Trigger(HLT)wihch is a combined effort of the Data Collection HLT and PESA(Physics and Event Selection Architecture)subgroups within the ATLAS TDAQ collaboration.Two important issues,alresdy outlined in the ATLAS HLT,DAQ and DCS Technical Proposal [1] will be highlighted:the treatment of the LVL2 Trigger and Event Filter as aspects of a general HLT with a view to easier migration of algorthms between the two levels;unification of the selective data collection for LVL2 and Event Building.

  7. Effects of vine water status on dimethyl sulfur potential, ammonium, and amino acid contents in Grenache Noir grapes (Vitis vinifera).

    Science.gov (United States)

    De Royer Dupré, N; Schneider, R; Payan, J C; Salançon, E; Razungles, A

    2014-04-02

    We studied the effect of vine water status on the dimethyl sulfur potential (DMSP), ammonium, and amino acid contents of the berry during the maturation of Grenache Noir grapes. Water deficit increased the accumulation of amino acids in berries and favored yeast assimilable amino nitrogen. Similarly, ammonium content was higher in berries from vines subjected to moderate water deficit. DMSP content followed the same trend as yeast assimilable amino acid content, with higher concentrations observed in the berries of vines subjected to water deficit. The high DMSP and yeast assimilable nitrogen contents of musts from vines subjected to water deficit resulted in a better preservation of DMSP during winemaking. The wines produced from these musts had a higher DMSP level and would therefore probably have a higher aroma shelf life, because the DMSP determines the rate of release of dimethyl sulfur during wine storage, and this compound enhances fruity notes.

  8. Maximizing ammonium nitrogen removal from solution using different zeolites.

    Science.gov (United States)

    Penn, Chad J; Warren, Jason G; Smith, Savannah

    2010-01-01

    Zeolite minerals are ideal for removing ammonium nitrogen (NH4(+)-N) from animal wastes, leachates, and industrial effluents. The objectives of this study were to compare NH4+ removal and kinetics among several commercially available zeolites under various conditions and determine if calorimetry could provide information regarding kinetics of NH4+ removal. Ammonium sorption onto potassium (K) saturated zeolites was compared using synthetic vs. natural swine effluent and with either traditional batch-shaken system or a "tea bag" approach in which zeolites were contained in a mesh sack and suspended in a solution of swine effluent. Ammonium sorption was measured at four retention times using a flow-through system, and the resulting heat response was measured using isothermal calorimetry. Ammonium removal was not significantly different in synthetic vs. natural swine effluent. Ammonium removal was lower in batch-stirred compared to batch-shaken systems, suggesting that diffusion between particles was rate-limiting in the former system. Flow-through cells possessing contact times > 100 s displayed greater NH4+ sorption than batch systems, suggesting that maintaining high NH4+ concentration in solution, removal of exchange products, and sufficient reaction time are critical to maximizing NH4+ removal by zeolites. Within 100 s after NH4+ addition, endothermic heat responses indicated that NH4(+)-K+ exchange had peaked; this was followed by significant heat rate reduction for 50 min. This confirmed findings of an initial fast NH4(+)-K+ exchange followed by a slower one and suggests the 100-s period of rapid reaction is an indicator of the minimum flow through retention time required to optimize NH4+ sorption to zeolites used in this study.

  9. High levels of molecular chlorine in the Arctic atmosphere

    Science.gov (United States)

    Liao, Jin; Huey, L. Gregory; Liu, Zhen; Tanner, David J.; Cantrell, Chris A.; Orlando, John J.; Flocke, Frank M.; Shepson, Paul B.; Weinheimer, Andrew J.; Hall, Samuel R.; Ullmann, Kirk; Beine, Harry J.; Wang, Yuhang; Ingall, Ellery D.; Stephens, Chelsea R.; Hornbrook, Rebecca S.; Apel, Eric C.; Riemer, Daniel; Fried, Alan; Mauldin, Roy L.; Smith, James N.; Staebler, Ralf M.; Neuman, J. Andrew; Nowak, John B.

    2014-02-01

    Chlorine radicals can function as a strong atmospheric oxidant, particularly in polar regions, where levels of hydroxyl radicals are low. In the atmosphere, chlorine radicals expedite the degradation of methane and tropospheric ozone, and the oxidation of mercury to more toxic forms. Here we present direct measurements of molecular chlorine levels in the Arctic marine boundary layer in Barrow, Alaska, collected in the spring of 2009 over a six-week period using chemical ionization mass spectrometry. We report high levels of molecular chlorine, of up to 400 pptv. Concentrations peaked in the early morning and late afternoon, and fell to near-zero levels at night. Average daytime molecular chlorine levels were correlated with ozone concentrations, suggesting that sunlight and ozone are required for molecular chlorine formation. Using a time-dependent box model, we estimate that the chlorine radicals produced from the photolysis of molecular chlorine oxidized more methane than hydroxyl radicals, on average, and enhanced the abundance of short-lived peroxy radicals. Elevated hydroperoxyl radical levels, in turn, promoted the formation of hypobromous acid, which catalyses mercury oxidation and the breakdown of tropospheric ozone. We therefore suggest that molecular chlorine exerts a significant effect on the atmospheric chemistry of the Arctic.

  10. Nitrogen concentrations in a small Mediterranean stream: 1. Nitrate 2. Ammonium

    Directory of Open Access Journals (Sweden)

    A. Butturini

    2002-01-01

    Full Text Available The importance of storm frequency as well as the groundwater and hyporheic inputs on nitrate (NO3-N and ammonium (NH4-N levels in stream water were studied in a small perennial Mediterranean catchment, Riera Major, in northeast Spain. NO3-N concentrations ranged from 0.15 to 1.9 mg l-1. Discharge explained 47% of the annual NO3-N concentration variance, but this percentage increased to 97% when single floods were analysed. The rate of change in nitrate concentration with respect to flow, ΔNO3-N/ΔQ, ranged widely from 0 to 20 μg NO3-N s l-2. The ΔNO3-N/ΔQ values fitted to a non linear model with respect to the storm flow magnitude (ΔQ (r2=0.48, d.f.=22, P3-N/ΔQ occurred at intermediate ΔQ values, whereas low ΔNO3-N/ΔQ values occurred during severe storms (ΔQ > 400 l s-1. N3-N concentrations exhibit anticlockwise hysteresis patterns with changing flow and the patterns observed for autumnal and winter storms indicated that groundwater was the main N3-N source for stream and hyporheic water. At baseflow, NO3-N concentration in groundwater was higher (t=4.75, d.f.=29, P>0.001 and co-varied with concentrations in the stream (r=0.91, d.f.=28, P3-N concentration in hyporheic water was identical to that in stream water. The role of the hyporheic zone as source or sink for ammonium was studied hyporheic was studied comparing its concentrations in stream and hyporheic zone before and after a major storm occurred in October 1994 that removed particulate organic matter stored in sediments. Results showed high ammonium concentrations (75±28 s.d. μg NH4-N l-1 before the storm flow in the hyporheic zone. After the storm, the ammonium concentration in the hyporheic dropped by 80% (13.6±8 μg N4-N l-1 and approached to the level found in stream water (11±8 μg NH4-N l-1 indicating that indisturbed hyporheic sediments act as a source for ammonium. After the storm, the ammonium concentrations in the stream, hyporheic and groundwater zones were very

  11. Quaternary ammonium salt N-(dodecyloxycarboxymethyl)-N,N,N-trimethyl ammonium chloride induced alterations in Saccharomyces cerevisiae physiology

    Indian Academy of Sciences (India)

    EWA OBŁĄK; AGATA PIECUCH; EWA MACIASZCZYK-DZIUBIŃSKA; DONATA WAWRZYCKA

    2016-12-01

    We investigated the influence of the quaternary ammonium salt (QAS) called IM (N-(dodecyloxycarboxymethyl)-N,N,N-trimethyl ammonium chloride) on yeast cells of the parental strain and the IM-resistant mutant (EO25 IMR)growth. The phenotype of this mutant was pleiotropic. The IMR mutant exhibited resistance to ethanol, osmotic shockand oxidative stress, as well as increased sensitivity to UV. Moreover, it was noted that mutant EO25 appears to havean increased resistance to clotrimazole, ketoconazole, fluconazole, nystatin and cycloheximide. It also toleratedgrowth in the presence of crystal violet, DTT and metals (selenium, tin, arsenic). It was shown that the presence ofIM decreased ergosterol level in mutant plasma membrane and increased its unsaturation. These results indicatechanges in the cell lipid composition. Western blot analysis showed the induction of Pma1 level by IM. RT-PCRrevealed an increased PMA1 expression after IM treatment.

  12. Liquid high-level waste storage - can we tolerate it?

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, P. [Terramares Group (United Kingdom)

    1996-12-31

    High-level radioactive waste from reprocessing is stored at British Nuclear Fuel`s Sellafield site in High Active Storage Tanks (HAST`s), which require constant cooling and ventilation. The author argues that, containing as they do, about 100 times the caesium 137 released during the Chernobyl accident, these containment tanks represent an unacceptably high risk of a major release of caesium 137, a volatile gamma-emitter with a half-life of about 30 years. It is readily transferred into food chains and difficult to remove from soils, tarmac and concrete. Still worse, it is argued, are the tens of thousands of cancers and other biological radiation effects likely to occur as a result of such a release. He argues for the vitrification of all such highly active liquid wastes, which would slow further reprocessing down to accommodate the current backlog. (UK).

  13. 以离子液体为流动相的高效液相色谱-间接紫外检测法分析四甲基按根离子%Analysis of Tetramethyl Ammonium Ion by High Performance Liquid Chromatography-Indirect Ultraviolet Detection Using Ionic Liquids as Mobile Phase

    Institute of Scientific and Technical Information of China (English)

    董影杰; 于泓; 王婧菲; 黄旭

    2011-01-01

    建立了四甲基铵根离子的反相高效液相色谱-间接紫外检测分析法.以ZORBAX ODS反相色谱柱为分离柱,采用间接紫外检测方法,考察了紫外检测波长和离子液体+有机溶剂(乙腈、甲醇)流动相对分离和测定四甲基铵根离子的影响.最佳色谱条件为:以80% 1-乙基-3-甲基咪唑四氟硼酸盐水溶液(0.5 mmol/L,乙酸调pH 3.5)+20%乙腈为流动相,检测波长210 nm,柱温30 ℃,进样体积20 μL,流速1.0 mL/min.在此条件下,四甲基铵根离子的检出限为2.60 mg/L (S/N= 3),保留时间和峰面积的相对标准偏差(n=5)分别为0.04%和0.31%,其标准曲线在10-204 mg/L范围内线性关系良好(r= 0.9999).将本方法应用于分析离子液体溴化四甲基铵中的四甲基铵根离子,其加标回收率为99.3%.%A method was developed for the determination of tetramethyl ammonium ion by reversed phase high performance liquid chromatography with indirect ultraviolet (UV) detection. Chromato-graphic separation was performed on a ZORBAX ODS reversed phase column using ionic liquids + organic solvents (acetonitrile or methanol) as mobile phase. Chromatographic detection was carried out by indirect UV detection. The effects of the ultraviolet detection wavelength and mobile phases on the separation and determination of tetramethyl ammonium ion were investigated. The optimized chromatographic conditions for the determination of tetramethyl ammonium ion were as follows: 80% 1-ethyl-3-methyl-imidazolium tetrafluoroborate aqueous solution (0. 5 mmol/L, pH 3. 5 adjusted with acetic acid) + 20% acetonitrile as mobile phase, detection wavelength 210 nm, column temperature 30 °C , flow rate 1. 0 mL/min. Under these conditions, the detection limit (S/N=3) of tetramethyl ammonium ion was 2. 60 mg/L. The relative standard deviations (RSD) of the chromatographic retention time and peak areas for tetramethyl ammonium ion were 0. 04% and 0. 3% (n = 5) , respec-tively. The calibration curve showed

  14. The High Level Trigger of the CMS experiment

    CERN Document Server

    Gao, Xuyang

    2016-01-01

    The CMS experiment has been designed with a 2-level trigger system the Level 1 Trigger, implemented on custom-designed electronics, and the High Level Trigger, a streamlined version of the CMS offline reconstruction software running on a computer farm. In this poster we will present the performance with the specific algorithms developed to cope with the increasing LHC pile-up and bunch crossing rate using 13 TeV data during 2015, and prospects for improvements brought to both L1T and HLT strategies to meet the new challenges for 2016 scenarios with a peak instantaneous luminosity of $1.2 \\times 10^{34} $cm$^{-2}$s$^{-1}$ and 30 pileup events.

  15. High asymmetric dimethylarginine (ADMA) levels in patients with brucellosis.

    Science.gov (United States)

    Mengeloglu, Zafer; Sünnetcioglu, Mahmut; Tosun, Mehmet; Kücükbayrak, Abdülkadir; Ceylan, Mehmet Resat; Baran, Ali Irfan; Karahocagil, Mustafa; Akdeniz, Hayrettin

    2014-02-01

    Asymmetric dimethylarginine (ADMA) is the main endogenous inhibitor of nitric oxide synthase and is considered to be associated with endothelial dysfunction. Brucellosis, a zoonotic disease caused by Brucella spp., can manifest as vasculopathy. The present study was performed to investigate the relationship between ADMA and brucellosis. Serum samples from 39 patients with an accurate diagnosis of brucellosis and from 18 healthy control individuals were included in this study. ADMA levels were significantly higher in the patient group than the controls (P brucellosis and high levels of ADMA. In conclusion, ADMA levels should be tested in brucellosis cases and that further studies to clarify the mechanism underlying the association between ADMA and brucellosis are required.

  16. Mammut: High-level management of system knobs and sensors

    Science.gov (United States)

    De Sensi, Daniele; Torquati, Massimo; Danelutto, Marco

    Managing low-level architectural features for controlling performance and power consumption is a growing demand in the parallel computing community. Such features include, but are not limited to: energy profiling, platform topology analysis, CPU cores disabling and frequency scaling. However, these low-level mechanisms are usually managed by specific tools, without any interaction between each other, thus hampering their usability. More important, most existing tools can only be used through a command line interface and they do not provide any API. Moreover, in most cases, they only allow monitoring and managing the same machine on which the tools are used. MAMMUT provides and integrates architectural management utilities through a high-level and easy-to-use object-oriented interface. By using MAMMUT, is possible to link together different collected information and to exploit them on both local and remote systems, to build architecture-aware applications.

  17. FLUIDIZED BED STEAM REFORMING ENABLING ORGANIC HIGH LEVEL WASTE DISPOSAL

    Energy Technology Data Exchange (ETDEWEB)

    Williams, M

    2008-05-09

    Waste streams planned for generation by the Global Nuclear Energy Partnership (GNEP) and existing radioactive High Level Waste (HLW) streams containing organic compounds such as the Tank 48H waste stream at Savannah River Site have completed simulant and radioactive testing, respectfully, by Savannah River National Laboratory (SRNL). GNEP waste streams will include up to 53 wt% organic compounds and nitrates up to 56 wt%. Decomposition of high nitrate streams requires reducing conditions, e.g. provided by organic additives such as sugar or coal, to reduce NOX in the off-gas to N2 to meet Clean Air Act (CAA) standards during processing. Thus, organics will be present during the waste form stabilization process regardless of the GNEP processes utilized and exists in some of the high level radioactive waste tanks at Savannah River Site and Hanford Tank Farms, e.g. organics in the feed or organics used for nitrate destruction. Waste streams containing high organic concentrations cannot be stabilized with the existing HLW Best Developed Available Technology (BDAT) which is HLW vitrification (HLVIT) unless the organics are removed by pretreatment. The alternative waste stabilization pretreatment process of Fluidized Bed Steam Reforming (FBSR) operates at moderate temperatures (650-750 C) compared to vitrification (1150-1300 C). The FBSR process has been demonstrated on GNEP simulated waste and radioactive waste containing high organics from Tank 48H to convert organics to CAA compliant gases, create no secondary liquid waste streams and create a stable mineral waste form.

  18. Sundance: High-Level Software for PDE-Constrained Optimization

    Directory of Open Access Journals (Sweden)

    Kevin Long

    2012-01-01

    Full Text Available Sundance is a package in the Trilinos suite designed to provide high-level components for the development of high-performance PDE simulators with built-in capabilities for PDE-constrained optimization. We review the implications of PDE-constrained optimization on simulator design requirements, then survey the architecture of the Sundance problem specification components. These components allow immediate extension of a forward simulator for use in an optimization context. We show examples of the use of these components to develop full-space and reduced-space codes for linear and nonlinear PDE-constrained inverse problems.

  19. High precision modeling at the 10^{-20} level

    CERN Document Server

    Andres, M; Costea, A; Hackmann, E; Herrmann, S; Lämmerzahl, C; Nesemann, L; Rievers, B; Stephan, E P

    2011-01-01

    The requirements for accurate numerical simulation are increasing constantly. Modern high precision physics experiments now exceed the achievable numerical accuracy of standard commercial and scientific simulation tools. One example are optical resonators for which changes in the optical length are now commonly measured to 10^{-15} precision. The achievable measurement accuracy for resonators and cavities is directly influenced by changes in the distances between the optical components. If deformations in the range of 10^{-15} occur, those effects cannot be modeled and analysed any more with standard methods based on double precision data types. New experimental approaches point out that the achievable experimental accuracies may improve down to the level of 10^{-17} in the near future. For the development and improvement of high precision resonators and the analysis of experimental data, new methods have to be developed which enable the needed level of simulation accuracy. Therefore we plan the development o...

  20. RETENTION OF SULFATE IN HIGH LEVEL RADIOACTIVE WASTE GLASS

    Energy Technology Data Exchange (ETDEWEB)

    Fox, K.

    2010-09-07

    High level radioactive wastes are being vitrified at the Savannah River Site for long term disposal. Many of the wastes contain sulfate at concentrations that can be difficult to retain in borosilicate glass. This study involves efforts to optimize the composition of a glass frit for combination with the waste to improve sulfate retention while meeting other process and product performance constraints. The fabrication and characterization of several series of simulated waste glasses are described. The experiments are detailed chronologically, to provide insight into part of the engineering studies used in developing frit compositions for an operating high level waste vitrification facility. The results lead to the recommendation of a specific frit composition and a concentration limit for sulfate in the glass for the next batch of sludge to be processed at Savannah River.

  1. Storage of High Level Nuclear Waste in Germany

    Directory of Open Access Journals (Sweden)

    Dietmar P. F. Möller

    2007-01-01

    Full Text Available Nuclear energy is very often used to generate electricity. But first the energy must be released from atoms what can be done in two ways: nuclear fusion and nuclear fission. Nuclear power plants use nuclear fission to produce electrical energy. The electrical energy generated in nuclear power plants does not produce polluting combustion gases but a renewable energy, an important fact that could play a key role helping to reduce global greenhouse gas emissions and tackling global warming especially as the electricity energy demand rises in the years ahead. This could be assumed as an ideal win-win situation, but the reverse site of the medal is that the production of high-level nuclear waste outweighs this advantage. Hence the paper attempt to highlight the possible state-of-art concepts for the safe and sustaining storage of high-level nuclear waste in Germany.

  2. Altitudinal Levels and Altitudinal Limits in High Mountains

    Institute of Scientific and Technical Information of China (English)

    Matthias Kuhle

    2007-01-01

    In lowlands climate-specific processes due to weathering and erosion are dominant, whilst the geomorphology of mountains is dependent on the geologic-tectonic structure, i.e., the energy of erosion that increases according to the vertical. The expression "extremely high mountains" has been established as the extreme of a continuous mountain classification. It has to be understood in terms of geomorphology, glaciology and vegetation.Correspondence of the planetary and hypsometric change of forms is of great value as synthetic explanation. It is confirmed with regard to vegetation,periglacial geomorphology and glaciology. Due to the world-wide reconstruction of the snowline its paleoclimatic importance increases, too. Apart from lower limits the periglacial and glacial altitudinal levels also show zones of optimum development and climatic upper limits in the highest mountains of the earth. According to the proportion of the altitudinal levels a classification as to arid, temperate and humid high mountains has been carried out.

  3. Management of data quality of high level waste characterization

    Energy Technology Data Exchange (ETDEWEB)

    Winters, W.I., Westinghouse Hanford

    1996-06-12

    Over the past 10 years, the Hanford Site has been transitioning from nuclear materials production to Site cleanup operations. High-level waste characterization at the Hanford Site provides data to support present waste processing operations, tank safety programs, and future waste disposal programs. Quality elements in the high-level waste characterization program will be presented by following a sample through the data quality objective, sampling, laboratory analysis and data review process. Transition from production to cleanup has resulted in changes in quality systems and program; the changes, as well as other issues in these quality programs, will be described. Laboratory assessment through quality control and performance evaluation programs will be described, and data assessments in the laboratory and final reporting in the tank characterization reports will be discussed.

  4. A high resolution water level forecast for the German Bight

    Science.gov (United States)

    Niehüser, Sebastian; Dangendorf, Sönke; Arns, Arne; Jensen, Jürgen

    2016-04-01

    Many coastal regions worldwide are potentially endangered by storm surges which can cause disastrous damages and loss of life. Due to climate change induced sea level rise, an accumulation of such events is expected by the end of the 21th century. Therefore, advanced storm surge warnings are needed to be prepared when another storm surge hits the coast. In the shallow southeastern North Sea these storm surge warnings are nowadays routinely provided for selected tide gauge locations along a coastline through state-of-the-art forecast systems, which are based on a coupled system of empirical tidal predictions and numerical storm surge forecasts. Along the German North Sea coastline, the Federal Maritime and Hydrographic Agency in cooperation with the German Weather Service is responsible for the storm surge warnings. They provide accurate, high frequency and real-time water level forecasts for up to six days ahead at selected tide gauge sites via internet, telephone and broadcast. Since water levels along the German North Sea coastline are dominated by shallow water effects and a very complex bathymetric structure of the seabed, the pointwise forecast is not necessarily transferable to un-gauged areas between the tide gauges. Here we aim to close this existing gap and develop water level forecasts with a high spatial (continuously with a resolution of at least 1 kilometer) as well as a high temporal (at least 15-minute values) resolution along the entire German North Sea coastline. We introduce a new methodology for water level forecasts which combines empirical or statistical and numerical models. While the tidal forecast is performed by non-parametric interpolation techniques between un-gauged and gauged sites, storm surges are estimated on the basis of statistical/empirical storm surge formulas taken from a numerical model hindcast. The procedure will be implemented in the operational mode forced with numerical weather forecasts.

  5. High-level waste management technology program plan

    Energy Technology Data Exchange (ETDEWEB)

    Harmon, H.D.

    1995-01-01

    The purpose of this plan is to document the integrated technology program plan for the Savannah River Site (SRS) High-Level Waste (HLW) Management System. The mission of the SRS HLW System is to receive and store SRS high-level wastes in a see and environmentally sound, and to convert these wastes into forms suitable for final disposal. These final disposal forms are borosilicate glass to be sent to the Federal Repository, Saltstone grout to be disposed of on site, and treated waste water to be released to the environment via a permitted outfall. Thus, the technology development activities described herein are those activities required to enable successful accomplishment of this mission. The technology program is based on specific needs of the SRS HLW System and organized following the systems engineering level 3 functions. Technology needs for each level 3 function are listed as reference, enhancements, and alternatives. Finally, FY-95 funding, deliverables, and schedules are s in Chapter IV with details on the specific tasks that are funded in FY-95 provided in Appendix A. The information in this report represents the vision of activities as defined at the beginning of the fiscal year. Depending on emergent issues, funding changes, and other factors, programs and milestones may be adjusted during the fiscal year. The FY-95 SRS HLW technology program strongly emphasizes startup support for the Defense Waste Processing Facility and In-Tank Precipitation. Closure of technical issues associated with these operations has been given highest priority. Consequently, efforts on longer term enhancements and alternatives are receiving minimal funding. However, High-Level Waste Management is committed to participation in the national Radioactive Waste Tank Remediation Technology Focus Area. 4 refs., 5 figs., 9 tabs.

  6. 76 FR 46907 - Ammonium Nitrate Security Program

    Science.gov (United States)

    2011-08-03

    ..., Kenya. See Corky Siemaszko, Wtc Chemicals In Kenya Blast (Aug. 14, 1998), http://www.nydailynews.com/archives/news/1998/08/14/1998-08-14_wtc_chemicals_in_kenya_blast.html (last visited May 11, 2011). Ammonium...

  7. 76 FR 70366 - Ammonium Nitrate Security Program

    Science.gov (United States)

    2011-11-14

    ...- accessible Internet access could obtain the access necessary to register online. 3. How to best notify... ammonium nitrate sellers (AN Sellers) when it is not possible for an AN Seller to verify the identity of...

  8. Effect of Ethylenediaminetetraacetic Acid and Ammonium Oxalate ...

    African Journals Online (AJOL)

    ADOWIE PERE

    acid and ammonium oxalate on the prevalence of microorganisms and removal of ... of water and applied at different time intervals; application on a day prior to .... and residual soil composition after plant exposure for 3 months. Treatment. C.

  9. High Level Information Fusion (HLIF) with nested fusion loops

    Science.gov (United States)

    Woodley, Robert; Gosnell, Michael; Fischer, Amber

    2013-05-01

    Situation modeling and threat prediction require higher levels of data fusion in order to provide actionable information. Beyond the sensor data and sources the analyst has access to, the use of out-sourced and re-sourced data is becoming common. Through the years, some common frameworks have emerged for dealing with information fusion—perhaps the most ubiquitous being the JDL Data Fusion Group and their initial 4-level data fusion model. Since these initial developments, numerous models of information fusion have emerged, hoping to better capture the human-centric process of data analyses within a machine-centric framework. 21st Century Systems, Inc. has developed Fusion with Uncertainty Reasoning using Nested Assessment Characterizer Elements (FURNACE) to address challenges of high level information fusion and handle bias, ambiguity, and uncertainty (BAU) for Situation Modeling, Threat Modeling, and Threat Prediction. It combines JDL fusion levels with nested fusion loops and state-of-the-art data reasoning. Initial research has shown that FURNACE is able to reduce BAU and improve the fusion process by allowing high level information fusion (HLIF) to affect lower levels without the double counting of information or other biasing issues. The initial FURNACE project was focused on the underlying algorithms to produce a fusion system able to handle BAU and repurposed data in a cohesive manner. FURNACE supports analyst's efforts to develop situation models, threat models, and threat predictions to increase situational awareness of the battlespace. FURNACE will not only revolutionize the military intelligence realm, but also benefit the larger homeland defense, law enforcement, and business intelligence markets.

  10. Case for retrievable high-level nuclear waste disposal

    Science.gov (United States)

    Roseboom, Eugene H.

    1994-01-01

    Plans for the nation's first high-level nuclear waste repository have called for permanently closing and sealing the repository soon after it is filled. However, the hydrologic environment of the proposed site at Yucca Mountain, Nevada, should allow the repository to be kept open and the waste retrievable indefinitely. This would allow direct monitoring of the repository and maintain the options for future generations to improve upon the disposal methods or use the uranium in the spent fuel as an energy resource.

  11. High-level Component Interfaces for Collaborative Development: A Proposal

    Directory of Open Access Journals (Sweden)

    Thomas Marlowe

    2009-12-01

    Full Text Available Software development has rapidly moved toward collaborative development models where multiple partners collaborate in creating and evolving software intensive systems or components of sophisticated ubiquitous socio-technical-ecosystems. In this paper we extend the concept of software interface to a flexible high-level interface as means for accommodating change and localizing, controlling and managing the exchange of knowledge and functional, behavioral, quality, project and business related information between the partners and between the developed components.

  12. Hanford long-term high-level waste management program

    Energy Technology Data Exchange (ETDEWEB)

    Wodrich, D.D.

    1976-06-24

    An overview of the Hanford Long-Term High-Level Waste Management Program is presented. Four topics are discussed: first, the kinds and quantities of waste that will exist and are included in this program; second, how the plan is structured to solve this problem; third, the alternative waste management methods being considered; and fourth, the technology program that is in progress to carry out this plan. (LK)

  13. Nuclear reactor high-level waste: origin and safe disposal

    Energy Technology Data Exchange (ETDEWEB)

    Chua, C.; Tsipis, K. (Massachusetts Inst. of Tech., Cambridge, MA (USA))

    High-level waste (HLW) is a natural component of the nuclear fuel cycle. Because of its radioactivity, HLW needs to be handled with great care. Different alternatives for permanently storing HLW are evaluated. Studies have shown that the disposal of HLW is safest when the waste is first vitrified before storage. Simple calculations show that vitrified HLW that is properly buried in deep, carefully chosen crystalline rock structures poses insignificant health risks. (author).

  14. Mixing Processes in High-Level Waste Tanks - Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Peterson, P.F.

    1999-05-24

    The mixing processes in large, complex enclosures using one-dimensional differential equations, with transport in free and wall jets is modeled using standard integral techniques. With this goal in mind, we have constructed a simple, computationally efficient numerical tool, the Berkeley Mechanistic Mixing Model, which can be used to predict the transient evolution of fuel and oxygen concentrations in DOE high-level waste tanks following loss of ventilation, and validate the model against a series of experiments.

  15. Execution of a High Level Real-Time Language

    OpenAIRE

    Luqi; Berzins, Valdis

    1988-01-01

    Prototype System Description Language (PSDL) is a high level real-time language with special features for hard real-time system specification and design. It can be used to firm up requirements through execution of its software prototypes The language is designed based on a real-time model merging data and control flow and its implementation is beyond conventional compiler technology because of the need to meet real-time constraints. In this paper we describe and illustrate our research result...

  16. Learning high-level features for chord recognition using Autoencoder

    Science.gov (United States)

    Phongthongloa, Vilailukkana; Kamonsantiroj, Suwatchai; Pipanmaekaporn, Luepol

    2016-07-01

    Chord transcription is valuable to do by itself. It is known that the manual transcription of chords is very tiresome, time-consuming. It requires, moreover, musical knowledge. Automatic chord recognition has recently attracted a number of researches in the Music Information Retrieval field. It has known that a pitch class profile (PCP) is the commonly signal representation of musical harmonic analysis. However, the PCP may contain additional non-harmonic noise such as harmonic overtones and transient noise. The problem of non-harmonic might be generating the sound energy in term of frequency more than the actual notes of the respective chord. Autoencoder neural network may be trained to learn a mapping from low level feature to one or more higher-level representation. These high-level representations can explain dependencies of the inputs and reduce the effect of non-harmonic noise. Then these improve features are fed into neural network classifier. The proposed high-level musical features show 80.90% of accuracy. The experimental results have shown that the proposed approach can achieve better performance in comparison with other based method.

  17. Handbook of high-level radioactive waste transportation

    Energy Technology Data Exchange (ETDEWEB)

    Sattler, L.R.

    1992-10-01

    The High-Level Radioactive Waste Transportation Handbook serves as a reference to which state officials and members of the general public may turn for information on radioactive waste transportation and on the federal government`s system for transporting this waste under the Civilian Radioactive Waste Management Program. The Handbook condenses and updates information contained in the Midwestern High-Level Radioactive Waste Transportation Primer. It is intended primarily to assist legislators who, in the future, may be called upon to enact legislation pertaining to the transportation of radioactive waste through their jurisdictions. The Handbook is divided into two sections. The first section places the federal government`s program for transporting radioactive waste in context. It provides background information on nuclear waste production in the United States and traces the emergence of federal policy for disposing of radioactive waste. The second section covers the history of radioactive waste transportation; summarizes major pieces of legislation pertaining to the transportation of radioactive waste; and provides an overview of the radioactive waste transportation program developed by the US Department of Energy (DOE). To supplement this information, a summary of pertinent federal and state legislation and a glossary of terms are included as appendices, as is a list of publications produced by the Midwestern Office of The Council of State Governments (CSG-MW) as part of the Midwestern High-Level Radioactive Waste Transportation Project.

  18. Design of secure operating systems with high security levels

    Institute of Scientific and Technical Information of China (English)

    QING SiHan; SHEN ChangXiang

    2007-01-01

    Numerous Internet security incidents have shown that support from secure operating systems is paramount to fighting threats posed by modern computing environments. Based on the requirements of the relevant national and international standards and criteria, in combination with our experience in the design and development of the ANSHENG v4.0 secure operating system with high security level (hereafter simply referred to as ANSHENG OS), this paper addresses the following key issues in the design of secure operating systems with high security levels: security architecture, security policy models, and covert channel analysis. The design principles of security architecture and three basic security models: confidentiality,integrity, and privilege control models are discussed, respectively. Three novel security models and new security architecture are proposed. The prominent features of these proposals, as well as their applications to the ANSHENG OS, are elaborated.Cover channel analysis (CCA) is a well-known hard problem in the design of secure operating systems with high security levels since to date it lacks a sound theoretical basis and systematic analysis approach. In order to resolve the fundamental difficulties of CCA, we have set up a sound theoretical basis for completeness of covert channel identification and have proposed a unified framework for covert channel identification and an efficient backward tracking search method. The successful application of our new proposals to the ANSHENG OS has shown that it can help ease and speedup the entire CCA process.

  19. Comparative Study of the Effect of Glucosamine and Free Ammonium on 4-Methylimidazole Formation.

    Science.gov (United States)

    Yu, Pei; Xu, Xian-Bing; Yu, Shu-Juan

    2015-09-16

    The effect of glucosamine analogues (glucosamine and acetylglucosamine) and free ammonium on the formation of 4-methylimidazole (4-MeI) was investigated in the caramel model reaction systems. Methylglyoxal (MGO) was detected after derivatization by high-performance liquid chromatography with a diode array detector (HPLC-DAD). 4-MeI in the Maillard reaction was tested using a high-performance cation exchange chromatography coupled with APCI-MS (HPCEC-MS). The levels of pyrazines tested by gas chromatography (GC) coupled with MS were applied to mark the condensation reaction between dicarbonyls and free ammonium. Results showed that the formation of 4-MeI and its precursor MGO was inhibited in glucosamine analogue model reaction systems. Besides, the results from pyrazines and brown intensity in glucosamine analogues model reaction systems indicated that glucosamine analogues mainly underwent the reaction of intra-intermolecular polymerization into melanoidins rather than the degradation reaction into MGO. Using glucosamine analogues to produce the caramel color with a low level of 4-MeI was applicable.

  20. High Levels of Molecular Chlorine found in the Arctic Atmosphere

    Science.gov (United States)

    Liao, J.; Huey, L. G.; Liu, Z.; Tanner, D.; Cantrell, C. A.; Orlando, J. J.; Flocke, F. M.; Shepson, P. B.; Weinheimer, A. J.; Hall, S. R.; Beine, H.; Wang, Y.; Ingall, E. D.; Thompson, C. R.; Hornbrook, R. S.; Apel, E. C.; Fried, A.; Mauldin, L.; Smith, J. N.; Staebler, R. M.; Neuman, J. A.; Nowak, J. B.

    2014-12-01

    Chlorine radicals are a strong atmospheric oxidant, particularly in polar regions where levels of hydroxyl radicals can be quite low. In the atmosphere, chlorine radicals expedite the degradation of methane and tropospheric ozone and the oxidation of mercury to more toxic forms. Here, we present direct measurements of molecular chlorine levels in the Arctic marine boundary layer in Barrow, Alaska, collected in the spring of 2009 over a six-week period using chemical ionization mass spectrometry. We detected high levels of molecular chlorine of up to 400 pptv. Concentrations peaked in the early morning and late afternoon and fell to near-zero levels at night. Average daytime molecular chlorine levels were correlated with ozone concentrations, suggesting that sunlight and ozone are required for molecular chlorine formation. Using a time-dependent box model, we estimated that the chlorine radicals produced from the photolysis of molecular chlorine on average oxidized more methane than hydroxyl radicals and enhanced the abundance of short-lived peroxy radicals. Elevated hydroperoxyl radical levels, in turn, promoted the formation of hypobromous acid, which catalyzed mercury oxidation and the breakdown of tropospheric ozone. Therefore, we propose that molecular chlorine exerts a significant effect on the atmospheric chemistry in the Arctic. While the formation mechanisms of molecular chlorine are not yet understood, the main potential sources of chlorine include snowpack, sea salt, and sea ice. There is recent evidence of molecular halogen (Br2 and Cl2) formation in the Arctic snowpack. The coverage and composition of the snow may control halogen chemistry in the Arctic. Changes of sea ice and snow cover in the changing climate may affect air-snow-ice interaction and have a significant impact on the levels of radicals, ozone, mercury and methane in the Arctic troposphere.

  1. Preparation of nanodispersed titania using stabilized ammonium nitrate melts

    KAUST Repository

    Raciulete, Monica

    2010-10-01

    An expedite one-step approach using simple precursors has been proposed to obtain metallic oxide compounds and exemplified by preparation of highly dispersed TiO2. The technique consists in heating to 400500 °C of molten ammonium nitrate stabilized with an organic nitrogen-containing compound (urea, melamine, ammonium oxalate) and containing dissolved metal salt precursor (TiOCl2). The crystallites of the resulting TiO2 demonstrated variable size and shape as a function of stabilizer used. Their activity in photocatalytic oxidation of formic acid also depends on the nature of the stabilizer. The catalysts as-prepared showed high photocatalytic performance, superior to that of the Degussa P25 reference. Nitrogen containing stabilizers play a double role of increasing the process safety and modifying the properties of the solid products. © 2010 Elsevier Inc. All rights reserved.

  2. The physiological and morphological phenotype of a yeast mutant resistant to the quaternary ammonium salt N-(dodecyloxycarboxymethyl)-N,N,N-trimethyl ammonium chloride.

    Science.gov (United States)

    Obłak, Ewa; Gamian, Andrzej; Adamski, Ryszard; Ułaszewski, Stanisław

    2010-06-01

    We investigated the action of the quaternary ammonium salt (QAS) called IM (N-(dodecyloxycarboxymethyl)-N,N,N-trimethyl ammonium chloride) on Saccharomyces cerevisiae yeast cells. Changes in the yeast cell ultrastructure were confirmed by electron microscopy. We treated resistant mutant cells with QAS, and confirmed destruction of the mutant cytoplasm, an increase in the thickness of the cell wall, separation of the cell wall from the cytoplasm, and the accumulation of numerous lipid droplets. We also observed a relatively high production of lipids in the cells of the parental wild-type strain Sigma1278b and in its IM-resistant (IM(R)) mutant in the presence of the QAS. The IM(R) mutant showed increased sensitivity to CaCl(2) and SDS, and resistance to ethidium bromide, chloramphenicol, erythromycin and osmotic shock. It also tolerated growth at low pH. We suggest that the resistance to IM could be connected with the level of permeability of the cell membrane because the IM(R) mutant was sensitive to this compound in vivo in the presence of SDS and guanidine hydrochloride, which cause increased permeability of the cell plasma membrane.

  3. d15N dynamics of ammonium and particulate nitrogen during the growth season of a eutrophic estuary

    DEFF Research Database (Denmark)

    De Brabandere, Loreto; Brion, N.; Elskens, M.;

    2007-01-01

    We monitored the stable nitrogen isotopic composition (d15N) of suspended matter and ammonium in the freshwater stretch of the Scheldt estuary (Belgium) over a full year to investigate for seasonal evolution and possible co-variation between isotopic signatures. The d15N value of ammonium remained...... rather constant during winter (average = +11.4 pro mille) but increased significantly with the spring and summer bloom, reaching values as high as +70 pro mille. This enrichment of the ammonium pool in 15N coincided with significant ammonium depletion during summer period, suggesting a close causal...

  4. High-Level Synthesis: Productivity, Performance, and Software Constraints

    Directory of Open Access Journals (Sweden)

    Yun Liang

    2012-01-01

    Full Text Available FPGAs are an attractive platform for applications with high computation demand and low energy consumption requirements. However, design effort for FPGA implementations remains high—often an order of magnitude larger than design effort using high-level languages. Instead of this time-consuming process, high-level synthesis (HLS tools generate hardware implementations from algorithm descriptions in languages such as C/C++ and SystemC. Such tools reduce design effort: high-level descriptions are more compact and less error prone. HLS tools promise hardware development abstracted from software designer knowledge of the implementation platform. In this paper, we present an unbiased study of the performance, usability and productivity of HLS using AutoPilot (a state-of-the-art HLS tool. In particular, we first evaluate AutoPilot using the popular embedded benchmark kernels. Then, to evaluate the suitability of HLS on real-world applications, we perform a case study of stereo matching, an active area of computer vision research that uses techniques also common for image denoising, image retrieval, feature matching, and face recognition. Based on our study, we provide insights on current limitations of mapping general-purpose software to hardware using HLS and some future directions for HLS tool development. We also offer several guidelines for hardware-friendly software design. For popular embedded benchmark kernels, the designs produced by HLS achieve 4X to 126X speedup over the software version. The stereo matching algorithms achieve between 3.5X and 67.9X speedup over software (but still less than manual RTL design with a fivefold reduction in design effort versus manual RTL design.

  5. Interaction between High-Level and Low-Level Image Analysis for Semantic Video Object Extraction

    Directory of Open Access Journals (Sweden)

    Andrea Cavallaro

    2004-06-01

    Full Text Available The task of extracting a semantic video object is split into two subproblems, namely, object segmentation and region segmentation. Object segmentation relies on a priori assumptions, whereas region segmentation is data-driven and can be solved in an automatic manner. These two subproblems are not mutually independent, and they can benefit from interactions with each other. In this paper, a framework for such interaction is formulated. This representation scheme based on region segmentation and semantic segmentation is compatible with the view that image analysis and scene understanding problems can be decomposed into low-level and high-level tasks. Low-level tasks pertain to region-oriented processing, whereas the high-level tasks are closely related to object-level processing. This approach emulates the human visual system: what one “sees” in a scene depends on the scene itself (region segmentation as well as on the cognitive task (semantic segmentation at hand. The higher-level segmentation results in a partition corresponding to semantic video objects. Semantic video objects do not usually have invariant physical properties and the definition depends on the application. Hence, the definition incorporates complex domain-specific knowledge and is not easy to generalize. For the specific implementation used in this paper, motion is used as a clue to semantic information. In this framework, an automatic algorithm is presented for computing the semantic partition based on color change detection. The change detection strategy is designed to be immune to the sensor noise and local illumination variations. The lower-level segmentation identifies the partition corresponding to perceptually uniform regions. These regions are derived by clustering in an N-dimensional feature space, composed of static as well as dynamic image attributes. We propose an interaction mechanism between the semantic and the region partitions which allows to

  6. Ultrasonic level sensors for liquids under high pressure

    Science.gov (United States)

    Zuckerwar, A. J.; Mazel, D. S.; Hodges, D. Y.

    1986-01-01

    An ultrasonic level sensor of novel design continuously measures the level of a liquid subjected to a high pressure (up to about 40 MPa), as is sometimes required for the effective transfer of the liquid. The sensor operates as a composite resonator fabricated from a standard high-pressure plug. A flat-bottom hole is machined into the plug along its center line. An ultrasonic transducer is bonded rigidly to the interior surface of the bottom wall, while the exterior surface is in contact with the liquid. Although the bottom wall is designed to satisfy the pressure code, it is still sufficiently thin to permit ready excitation of the axisymmetric plate modes of vibration. The liquid level is measured by a conventional pulse-echo technique. A prototype sensor was tested successfully in a 2300-l water vessel at pressures up to about 37 MPa. A spectral analysis of the transmitted pulse reveals that the flexural, extensional, thickness-shear, and radial plate modes are excited into vibration, but none of these appears to be significantly affected by the pressurization of the liquid.

  7. Use of ammonium formate in QuEChERS for high-throughput analysis of pesticides in food by fast, low-pressure gas chromatography and liquid chromatography tandem mass spectrometry.

    Science.gov (United States)

    González-Curbelo, Miguel Ángel; Lehotay, Steven J; Hernández-Borges, Javier; Rodríguez-Delgado, Miguel Ángel

    2014-09-01

    The "quick, easy, cheap, effective, rugged, and safe" (QuEChERS) approach to sample preparation is widely applied in pesticide residue analysis, but the use of magnesium sulfate and other nonvolatile compounds for salting out in the method is not ideal for mass spectrometry. In this study, we developed and evaluated three new different versions of the QuEChERS method using more volatile salts (ammonium chloride and ammonium formate and acetate buffers) to induce phase separation and extraction of 43 representative pesticide analytes of different classes. Fast low-pressure gas chromatography tandem mass spectrometry (LPGC-MS/MS) and liquid chromatography (LC)-MS/MS were used for analysis. The QuEChERS AOAC Official Method 2007.01 was also tested for comparison purposes. Of the studied methods, formate buffering using 7.5g of ammonium formate and 15mL of 5% (v/v) formic acid in acetonitrile for the extraction of 15g of sample (5g for wheat grain) provided the best performance and practical considerations. Method validation was carried out with and without the use of dispersive solid-phase extraction for cleanup, and no significant differences were observed for the majority of pesticides. The method was demonstrated in quantitative analysis for GC- and LC-amenable pesticides in 4 representative food matrices (apple, lemon, lettuce, and wheat grain). With the typical exceptions of certain pH-dependent and labile pesticides, 90-110% recoveries and food applications.

  8. The ATLAS High Level Trigger Configuration and Steering

    CERN Document Server

    Stelzer, J; The ATLAS collaboration

    2010-01-01

    In March 2010 the four LHC experiments saw the first proton-proton collisions at 7 TeV. Still within the year a collision rate of nearly 10 MHz is expected. At ATLAS, events of potential interest for ATLAS physics are selected by a three level trigger system, with a final recording rate of about 200 Hz. The first level (L1) is implemented in customized hardware, the two levels of the high level trigger (HLT) are software triggers. Within the ATLAS physics program more than 500 trigger signatures are defined. The HLT tests each signature on each L1-accepted event, the test outcome is recorded for later analysis. The HLT-Steering is responsible for this. It foremost ensures the independent test of each signature, guarantying unbiased trigger decisions. Yet, to minimize data readout and execution time, cached detector data and once-calculated trigger objects are reused to form the decision. Some signature tests are performed only on a scaled-down fraction of candidate events, in order to reduce the output rate a...

  9. 77 FR 65532 - Solid Fertilizer Grade Ammonium Nitrate From the Russian Federation: Notice of Rescission of...

    Science.gov (United States)

    2012-10-29

    ... International Trade Administration Solid Fertilizer Grade Ammonium Nitrate From the Russian Federation: Notice... the antidumping duty order on solid fertilizer grade ammonium nitrate (ammonium nitrate) from the... Administrative Review: Solid Fertilizer Grade Ammonium Nitrate (Ammonium Nitrate) from the Russian...

  10. Preparation and characteristic research of anhydrous magnesium chloride with dehydrated ammonium carnallite

    Institute of Scientific and Technical Information of China (English)

    ZHOU Ning-bo; CHEN Bai-zhen; HE Xin-kuai; LI Yi-bing

    2006-01-01

    Taking the saline lake bischofite and NH4Cl that was removed with the ammonia method and continuwas synthesized. And then the ammonium carnallite was dehydrated to some extent at 160℃ for 4 h. Ammonium carnallite reacted with ammonia at 240℃ for 150 min and the ammonation ammonium carnallite was produced. Finally, the ammonation ammonium carnallite was calcined at 750℃ into anhydrous magnesium chloride containing only 0.1% (mass fraction) of MgO. On the other hand, dehydrated ammonium carnallite was mixed with the solid ammonium chloride at mass ratio 1:4 at high temperature and with the differential pressure of HN3 above 30.5 kPa. The dehydrated ammonium carnallite of mixture was dehydrated at 410℃, and then calcined at 700℃ into anhydrous magnesium chloride with only 0. 087% (mass fraction) of MgO. X-ray diffraction and electron microscopy analysis results prove that anhydrous magnesium chloride obtained by both methods hasn't mixed phases, the particle is large and even has good dispersion, which is suitable for preparation of metal magnesium in the electrolysis.

  11. Engineering Escherichia coli for high-level production of propionate.

    Science.gov (United States)

    Akawi, Lamees; Srirangan, Kajan; Liu, Xuejia; Moo-Young, Murray; Perry Chou, C

    2015-07-01

    Mounting environmental concerns associated with the use of petroleum-based chemical manufacturing practices has generated significant interest in the development of biological alternatives for the production of propionate. However, biological platforms for propionate production have been limited to strict anaerobes, such as Propionibacteria and select Clostridia. In this work, we demonstrated high-level heterologous production of propionate under microaerobic conditions in engineered Escherichia coli. Activation of the native Sleeping beauty mutase (Sbm) operon not only transformed E. coli to be propionogenic (i.e., propionate-producing) but also introduced an intracellular "flux competition" between the traditional C2-fermentative pathway and the novel C3-fermentative pathway. Dissimilation of the major carbon source of glycerol was identified to critically affect such "flux competition" and, therefore, propionate synthesis. As a result, the propionogenic E. coli was further engineered by inactivation or overexpression of various genes involved in the glycerol dissimilation pathways and their individual genetic effects on propionate production were investigated. Generally, knocking out genes involved in glycerol dissimilation (except glpA) can minimize levels of solventogenesis and shift more dissimilated carbon flux toward the C3-fermentative pathway. For optimal propionate production with high C3:C2-fermentative product ratios, glycerol dissimilation should be channeled through the respiratory pathway and, upon suppressed solventogenesis with minimal production of highly reduced alcohols, the alternative NADH-consuming route associated with propionate synthesis can be critical for more flexible redox balancing. With the implementation of various biochemical and genetic strategies, high propionate titers of more than 11 g/L with high yields up to 0.4 g-propionate/g-glycerol (accounting for ~50 % of dissimilated glycerol) were achieved, demonstrating the

  12. Effects of high vs low-level radiation exposure

    Energy Technology Data Exchange (ETDEWEB)

    Bond, V.P.

    1983-01-01

    In order to appreciate adequately the various possible effects of radiation, particularly from high-level vs low-level radiation exposure (HLRE, vs LLRE), it is necessary to understand the substantial differences between (a) exposure as used in exposure-incidence curves, which are always initially linear and without threshold, and (b) dose as used in dose-response curves, which always have a threshold, above which the function is curvilinear with increasing slope. The differences are discussed first in terms of generally familiar nonradiation situations involving dose vs exposure, and then specifically in terms of exposure to radiation, vs a dose of radiation. Examples are given of relevant biomedical findings illustrating that, while dose can be used with HLRE, it is inappropriate and misleading the LLRE where exposure is the conceptually correct measure of the amount of radiation involved.

  13. Quasimonomorphic Mononucleotide Repeats for High-Level Microsatellite Instability Analysis

    Directory of Open Access Journals (Sweden)

    Olivier Buhard

    2004-01-01

    Full Text Available Microsatellite instability (MSI analysis is becoming more and more important to detect sporadic primary tumors of the MSI phenotype as well as in helping to determine Hereditary Non-Polyposis Colorectal Cancer (HNPCC cases. After some years of conflicting data due to the absence of consensus markers for the MSI phenotype, a meeting held in Bethesda to clarify the situation proposed a set of 5 microsatellites (2 mononucleotide repeats and 3 dinucleotide repeats to determine MSI tumors. A second Bethesda consensus meeting was held at the end of 2002. It was discussed here that the 1998 microsatellite panel could underestimate high-level MSI tumors and overestimate low-level MSI tumors. Amongst the suggested changes was the exclusive use of mononucleotide repeats in place of dinucleotide repeats. We have already proposed a pentaplex MSI screening test comprising 5 quasimonomorphic mononucleotide repeats. This article compares the advantages of mono or dinucleotide repeats in determining microsatellite instability.

  14. Distribution of levels in high-dimensional random landscapes

    CERN Document Server

    Kabluchko, Zakhar

    2010-01-01

    We prove empirical central limit theorems for the distribution of levels of various random fields defined on high-dimensional discrete structures as the dimension of the structure goes to $\\infty$. The random fields considered include costs of assignments, lengths of Hamiltonian cycles and spanning trees, energies of directed polymers, locations of particles in the branching random walk, as well as energies in the Sherrington--Kirkpatrick and Edwards--Anderson models. The distribution of levels in all models listed above is shown to be essentially the same as in a stationary Gaussian process with regularly varying non-summable covariance function. This type of behavior is different from the Brownian bridge-type limit known for independent or stationary weakly dependent sequences of random variables.

  15. High level secretion of cellobiohydrolases by Saccharomyces cerevisiae

    Directory of Open Access Journals (Sweden)

    Ahlgren Simon

    2011-09-01

    Full Text Available Abstract Background The main technological impediment to widespread utilization of lignocellulose for the production of fuels and chemicals is the lack of low-cost technologies to overcome its recalcitrance. Organisms that hydrolyze lignocellulose and produce a valuable product such as ethanol at a high rate and titer could significantly reduce the costs of biomass conversion technologies, and will allow separate conversion steps to be combined in a consolidated bioprocess (CBP. Development of Saccharomyces cerevisiae for CBP requires the high level secretion of cellulases, particularly cellobiohydrolases. Results We expressed various cellobiohydrolases to identify enzymes that were efficiently secreted by S. cerevisiae. For enhanced cellulose hydrolysis, we engineered bimodular derivatives of a well secreted enzyme that naturally lacks the carbohydrate-binding module, and constructed strains expressing combinations of cbh1 and cbh2 genes. Though there was significant variability in the enzyme levels produced, up to approximately 0.3 g/L CBH1 and approximately 1 g/L CBH2 could be produced in high cell density fermentations. Furthermore, we could show activation of the unfolded protein response as a result of cellobiohydrolase production. Finally, we report fermentation of microcrystalline cellulose (Avicel™ to ethanol by CBH-producing S. cerevisiae strains with the addition of beta-glucosidase. Conclusions Gene or protein specific features and compatibility with the host are important for efficient cellobiohydrolase secretion in yeast. The present work demonstrated that production of both CBH1 and CBH2 could be improved to levels where the barrier to CBH sufficiency in the hydrolysis of cellulose was overcome.

  16. CEMENTITIOUS GROUT FOR CLOSING SRS HIGH LEVEL WASTE TANKS - #12315

    Energy Technology Data Exchange (ETDEWEB)

    Langton, C.; Burns, H.; Stefanko, D.

    2012-01-10

    In 1997, the first two United States Department of Energy (US DOE) high level waste tanks (Tanks 17-F and 20-F: Type IV, single shell tanks) were taken out of service (permanently closed) at the Savannah River Site (SRS). In 2012, the DOE plans to remove from service two additional Savannah River Site (SRS) Type IV high-level waste tanks, Tanks 18-F and 19-F. These tanks were constructed in the late 1950's and received low-heat waste and do not contain cooling coils. Operational closure of Tanks 18-F and 19-F is intended to be consistent with the applicable requirements of the Resource Conservation and Recovery Act (RCRA) and the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) and will be performed in accordance with South Carolina Department of Health and Environmental Control (SCDHEC). The closure will physically stabilize two 4.92E+04 cubic meter (1.3 E+06 gallon) carbon steel tanks and isolate and stabilize any residual contaminants left in the tanks. The closure will also fill, physically stabilize and isolate ancillary equipment abandoned in the tanks. A Performance Assessment (PA) has been developed to assess the long-term fate and transport of residual contamination in the environment resulting from the operational closure of the F-Area Tank Farm (FTF) waste tanks. Next generation flowable, zero-bleed cementitious grouts were designed, tested, and specified for closing Tanks 18-F and 19-F and for filling the abandoned equipment. Fill requirements were developed for both the tank and equipment grouts. All grout formulations were required to be alkaline with a pH of 12.4 and chemically reduction potential (Eh) of -200 to -400 to stabilize selected potential contaminants of concern. This was achieved by including Portland cement and Grade 100 slag in the mixes, respectively. Ingredients and proportions of cementitious reagents were selected and adjusted, respectively, to support the mass placement strategy developed by

  17. Stagnation Region Heat Transfer Augmentation at Very High Turbulence Levels

    Energy Technology Data Exchange (ETDEWEB)

    Ames, Forrest [University of North Dakota; Kingery, Joseph E. [University of North Dakota

    2015-06-17

    A database for stagnation region heat transfer has been extended to include heat transfer measurements acquired downstream from a new high intensity turbulence generator. This work was motivated by gas turbine industry heat transfer designers who deal with heat transfer environments with increasing Reynolds numbers and very high turbulence levels. The new mock aero-combustor turbulence generator produces turbulence levels which average 17.4%, which is 37% higher than the older turbulence generator. The increased level of turbulence is caused by the reduced contraction ratio from the liner to the exit. Heat transfer measurements were acquired on two large cylindrical leading edge test surfaces having a four to one range in leading edge diameter (40.64 cm and 10.16 cm). Gandvarapu and Ames [1] previously acquired heat transfer measurements for six turbulence conditions including three grid conditions, two lower turbulence aero-combustor conditions, and a low turbulence condition. The data are documented and tabulated for an eight to one range in Reynolds numbers for each test surface with Reynolds numbers ranging from 62,500 to 500,000 for the large leading edge and 15,625 to 125,000 for the smaller leading edge. The data show augmentation levels of up to 136% in the stagnation region for the large leading edge. This heat transfer rate is an increase over the previous aero-combustor turbulence generator which had augmentation levels up to 110%. Note, the rate of increase in heat transfer augmentation decreases for the large cylindrical leading edge inferring only a limited level of turbulence intensification in the stagnation region. The smaller cylindrical leading edge shows more consistency with earlier stagnation region heat transfer results correlated on the TRL (Turbulence, Reynolds number, Length scale) parameter. The downstream regions of both test surfaces continue to accelerate the flow but at a much lower rate than the leading edge. Bypass transition occurs

  18. High level radioactive waste (HLW) disposal a global challenge

    CERN Document Server

    PUSCH, R; NAKANO, M

    2011-01-01

    High Level Radioactive Waste (HLW) Disposal, A Global Challenge presents the most recent information on proposed methods of disposal for the most dangerous radioactive waste and for assessing their function from short- and long-term perspectives. It discusses new aspects of the disposal of such waste, especially HLW.The book is unique in the literature in making it clear that, due to tectonics and long-term changes in rock structure, rock can serve only as a ""mechanical support to the chemical apparatus"" and that effective containment of hazardous elements can only be managed by properly des

  19. High level trigger online calibration framework in ALICE

    Energy Technology Data Exchange (ETDEWEB)

    Bablok, S R; Djuvsland, Oe; Kanaki, K; Nystrand, J; Richter, M; Roehrich, D; Skjerdal, K; Ullaland, K; Oevrebekk, G; Larsen, D; Alme, J [Department of Physics and Technology, University of Bergen (Norway); Alt, T; Lindenstruth, V; Steinbeck, T M; Thaeder, J; Kebschull, U; Boettger, S; Kalcher, S; Lara, C; Panse, R [Kirchhoff Institute of Physics, Ruprecht-Karls-University Heidelberg (Germany)], E-mail: Sebastian.Bablok@uib.no (and others)

    2008-07-01

    The ALICE High Level Trigger (HLT) is designed to perform event analysis of heavy ion and proton-proton collisions as well as calibration calculations online. A large PC farm, currently under installation, enables analysis algorithms to process these computationally intensive tasks. The HLT receives event data from all major detectors in ALICE. Interfaces to the various other systems provide the analysis software with required additional information. Processed results are sent back to the corresponding systems. To allow online performance monitoring of the detectors an interface for visualizing these results has been developed.

  20. FPGA Co-processor for the ALICE High Level Trigger

    CERN Document Server

    Grastveit, G; Lindenstruth, V.; Loizides, C.; Roehrich, D.; Skaali, B.; Steinbeck, T.; Stock, R.; Tilsner, H.; Ullaland, K.; Vestbo, A.; Vik, T.

    2003-01-01

    The High Level Trigger (HLT) of the ALICE experiment requires massive parallel computing. One of the main tasks of the HLT system is two-dimensional cluster finding on raw data of the Time Projection Chamber (TPC), which is the main data source of ALICE. To reduce the number of computing nodes needed in the HLT farm, FPGAs, which are an intrinsic part of the system, will be utilized for this task. VHDL code implementing the Fast Cluster Finder algorithm, has been written, a testbed for functional verification of the code has been developed, and the code has been synthesized

  1. Market Designs for High Levels of Variable Generation: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Milligan, M.; Holttinen, H.; Kiviluoma, J.; Orths, A.; Lynch, M.; Soder, L.

    2014-10-01

    Variable renewable generation is increasing in penetration in modern power systems, leading to higher variability in the supply and price of electricity as well as lower average spot prices. This raises new challenges, particularly in ensuring sufficient capacity and flexibility from conventional technologies. Because the fixed costs and lifetimes of electricity generation investments are significant, designing markets and regulations that ensure the efficient integration of renewable generation is a significant challenge. This papers reviews the state of play of market designs for high levels of variable generation in the United States and Europe and considers new developments in both regions.

  2. High-level neutron coincidence counter maintenance manual

    Energy Technology Data Exchange (ETDEWEB)

    Swansen, J.; Collinsworth, P.

    1983-05-01

    High-level neutron coincidence counter operational (field) calibration and usage is well known. This manual makes explicit basic (shop) check-out, calibration, and testing of new units and is a guide for repair of failed in-service units. Operational criteria for the major electronic functions are detailed, as are adjustments and calibration procedures, and recurrent mechanical/electromechanical problems are addressed. Some system tests are included for quality assurance. Data on nonstandard large-scale integrated (circuit) components and a schematic set are also included.

  3. High Level Synthesis for Loop-Based BIST

    Institute of Scientific and Technical Information of China (English)

    李晓维; 张英相

    2000-01-01

    Area and test time are two major overheads encountered during data path high level synthesis for BIST. This paper presents an approach to behavioral synthesis for loop-based BIST. By taking into account the requirements of the BIST scheme during behavioral synthesis processes, an area optimal BIST solution can be obtained. This approach is based on the use of test resources reusability that results in a fewer number of registers being modified to be test registers. This is achieved by incorporating self-testability constraints during register assignment operations. Experimental results on benchmarks are presented to demonstrate the effectiveness of the approach.

  4. Combinatorial polarization, code loops, and codes of high level

    Directory of Open Access Journals (Sweden)

    Petr Vojtěchovský

    2004-07-01

    Full Text Available We first find the combinatorial degree of any map f:V→F, where F is a finite field and V is a finite-dimensional vector space over F. We then simplify and generalize a certain construction, due to Chein and Goodaire, that was used in characterizing code loops as finite Moufang loops that possess at most two squares. The construction yields binary codes of high divisibility level with prescribed Hamming weights of intersections of codewords.

  5. Characterizing speed-independence of high-level designs

    DEFF Research Database (Denmark)

    Kishinevsky, Michael; Staunstrup, Jørgen

    1994-01-01

    types, and internal as well as external non-determinism. This makes it possible to verify the speed-independence of a design without providing an explicit realization of the environment. The verification can be done mechanically. A number of experimental designs have been verified including a speed......This paper characterizes the speed-independence of high-level designs. The characterization is a condition on the design description ensuring that the behavior of the design is independent of the speeds of its components. The behavior of a circuit is modeled as a transition system, that allows data...

  6. Corrosion and failure processes in high-level waste tanks

    Energy Technology Data Exchange (ETDEWEB)

    Mahidhara, R.K.; Elleman, T.S.; Murty, K.L. [North Carolina State Univ., Raleigh, NC (United States)

    1992-11-01

    A large amount of radioactive waste has been stored safely at the Savannah River and Hanford sites over the past 46 years. The aim of this report is to review the experimental corrosion studies at Savannah River and Hanford with the intention of identifying the types and rates of corrosion encountered and indicate how these data contribute to tank failure predictions. The compositions of the High-Level Wastes, mild steels used in the construction of the waste tanks and degradation-modes particularly stress corrosion cracking and pitting are discussed. Current concerns at the Hanford Site are highlighted.

  7. Ammonium nitrate and iron nutrition effects on some nitrogen assimilation enzymes and metabolites in Spirulina platensis.

    Science.gov (United States)

    Esen, Merve; Ozturk Urek, Raziye

    2015-01-01

    The effect of various concentrations of ammonium nitrate (5-60 mM), an economical nitrogen source, on the growth, nitrate-ammonium uptake rates, production of some pigments and metabolites, and some nitrogen assimilation enzymes such as nitrate reductase (NR), nitrite reductase (NiR), glutamine synthetase (GS), and glutamate synthase (GOGAT) in Spirulina platensis (Gamont) Geitler was investigated. Ten millimolars of ammonium nitrate stimulated the growth, production of pigments and the other metabolites, and enzyme activities, whereas 30 and 60 mM ammonium nitrate caused inhibition. In the presence of 10 mM ammonium nitrate, different concentrations of iron were tried in the growth media of S. platensis. After achieving the best growth, levels of metabolite and pigment production, and enzyme activities in the presence of 10 mM ammonium nitrate as a nitrogen source, different iron concentrations (10-100 µM) were tried in the growth medium of S. platensis. The highest growth, pigment and metabolite levels, and enzyme activities were determined in the medium containing 50 µM iron and 10 mM ammonium nitrate. In this optimum condition, the highest dry biomass level, chlorophyll a, and pyruvate contents were obtained as 55.42 ± 3.8 mg mL(-1) , 93.114 ± 7.9 µg g(-1) , and 212.5 ± 18.7 µg g(-1) , respectively. The highest NR, NiR, GS, and GOGAT activities were 67.16 ± 5.1, 777.92 ± 52, 0.141 ± 0.01, and 44.45 ± 3.6, respectively. Additionally, 10 mM ammonium nitrate is an economical and efficient nitrogen source for nitrogen assimilation of S. platensis, and 50 µM iron is optimum for the growth of S. platensis. © 2014 International Union of Biochemistry and Molecular Biology, Inc.

  8. Online Pattern Recognition for the ALICE High Level Trigger

    CERN Document Server

    Lindenstruth, V; Röhrich, D; Skaali, B; Steinbeck, T M; Stock, Reinhard; Tilsner, H; Ullaland, K; Vestbø, A S; Vik, T

    2004-01-01

    The ALICE High Level Trigger has to process data online, in order to select interesting (sub)events, or to compress data efficiently by modeling techniques.Focusing on the main data source, the Time Projection Chamber (TPC), we present two pattern recognition methods under investigation: a sequential approach "cluster finder" and "track follower") and an iterative approach ("track candidate finder" and "cluster deconvoluter"). We show, that the former is suited for pp and low multiplicity PbPb collisions, whereas the latter might be applicable for high multiplicity PbPb collisions, if it turns out, that more than 8000 charged particles would have to be reconstructed inside the TPC. Based on the developed tracking schemes we show, that using modeling techniques a compression factor of around 10 might be achievable

  9. Online Pattern Recognition for the ALICE High Level Trigger

    Science.gov (United States)

    Lindenstruth, V.; Loizides, C.; Rohrich, D.; Skaali, B.; Steinbeck, T.; Stock, R.; Tilsner, H.; Ullaland, K.; Vestbo, A.; Vik, T.

    2004-06-01

    The ALICE high level trigger has to process data online, in order to select interesting (sub)events, or to compress data efficiently by modeling techniques. Focusing on the main data source, the time projection chamber (TPC), we present two pattern recognition methods under investigation: a sequential approach (cluster finder and track follower) and an iterative approach (track candidate finder and cluster deconvoluter). We show, that the former is suited for pp and low multiplicity PbPb collisions, whereas the latter might be applicable for high multiplicity PbPb collisions of dN/dy>3000. Based on the developed tracking schemes we show that using modeling techniques, a compression factor of around 10 might be achievable.

  10. High Level Trigger System for the ALICE Experiment

    Institute of Scientific and Technical Information of China (English)

    U.Frankenfeld; H.Helstrup; 等

    2001-01-01

    The ALICE experiment [1] at the Large Hadron Collider(LHC) at CERN will detect up to 20,000 particles in a single Pb-Pb event resulting in a data rate of -75 MByte/event,The event rate is limited by the bandwidth of the data storage system.Higher rates are possible by selecting interesting events and subevents (High Level trigger) or compressing the data efficiently with modeling techniques.Both require a fast parallel pattern recognition.One possible solution to process the detector data at such rates is a farm of clustered SMP nodes,based on off-the-shelf PCs,and connected by a high bandwidt,low latency network.

  11. Psilocybin impairs high-level but not low-level motion perception.

    Science.gov (United States)

    Carter, Olivia L; Pettigrew, John D; Burr, David C; Alais, David; Hasler, Felix; Vollenweider, Franz X

    2004-08-26

    The hallucinogenic serotonin(1A&2A) agonist psilocybin is known for its ability to induce illusions of motion in otherwise stationary objects or textured surfaces. This study investigated the effect of psilocybin on local and global motion processing in nine human volunteers. Using a forced choice direction of motion discrimination task we show that psilocybin selectively impairs coherence sensitivity for random dot patterns, likely mediated by high-level global motion detectors, but not contrast sensitivity for drifting gratings, believed to be mediated by low-level detectors. These results are in line with those observed within schizophrenic populations and are discussed in respect to the proposition that psilocybin may provide a model to investigate clinical psychosis and the pharmacological underpinnings of visual perception in normal populations.

  12. Ammonium and nitrite oxidation at nanomolar oxygen concentrations in oxygen minimum zone waters.

    Science.gov (United States)

    Bristow, Laura A; Dalsgaard, Tage; Tiano, Laura; Mills, Daniel B; Bertagnolli, Anthony D; Wright, Jody J; Hallam, Steven J; Ulloa, Osvaldo; Canfield, Donald E; Revsbech, Niels Peter; Thamdrup, Bo

    2016-09-20

    A major percentage of fixed nitrogen (N) loss in the oceans occurs within nitrite-rich oxygen minimum zones (OMZs) via denitrification and anammox. It remains unclear to what extent ammonium and nitrite oxidation co-occur, either supplying or competing for substrates involved in nitrogen loss in the OMZ core. Assessment of the oxygen (O2) sensitivity of these processes down to the O2 concentrations present in the OMZ core (Michaelis-Menten model, indicating a high-affinity component with a Km of just a few nanomolar. As the communities of ammonium and nitrite oxidizers were similar to other OMZs, these kinetics should apply across OMZ systems. The high O2 affinities imply that ammonium and nitrite oxidation can occur within the OMZ core whenever O2 is supplied, for example, by episodic intrusions. These processes therefore compete with anammox and denitrification for ammonium and nitrite, thereby exerting an important control over nitrogen loss.

  13. Thorium adsorption behaviour on mixed ammonium lanthanum oxalate, LAOX

    Energy Technology Data Exchange (ETDEWEB)

    Valentini Ganzerli, M.T.; Maggi, L.; Crespi Caramella, V

    1999-07-01

    The cation-exchange properties of mixed ammonium lanthanum oxalate, LAOX, were studied by batch equilibration as a function of the concentration of some cations, such as alkaline earths or ammonium and of some anions and acids. The distribution coefficients for thorium are high, while U(VI) is not adsorbed over a large acidity range. Thus, the separation of thorium from uranium may be successfully carried out. The experimental conditions of adsorption, elution and recovery of thorium were investigated as well, by using chromatographic columns filled with LAOX, in order to set best the separation conditions from uranyl ions. Instrumental neutron activation analysis, ICP emission spectrometry and the UV spectrometry were used to evaluate the thorium, uranium and lanthanum concentrations00.

  14. N-Acetyl Cysteine (NAC)-Directed Detoxification of Methacryloxylethyl Cetyl Ammonium Chloride (DMAE-CB).

    Science.gov (United States)

    Jiao, Yang; Ma, Sai; Li, Jing; Shan, Lequn; Wang, Yingjie; Tian, Min; Yang, Yanwei; Sun, Jinlong; Ban, Jinghao; Chen, Jihua

    2015-01-01

    Methacryloxylethyl cetyl ammonium chloride (DMAE-CB) is a polymerizable antibacterial monomer and has been proved as an effective strategy to achieve bioactive bonding with reliable bacterial inhibitory effects. However, the toxicity of DMAE-CB may hamper its wide application in clinical situations. Thus, this study was designed to investigate the toxicity of DMAE-CB and explore the possible protective effects of N-acetyl cysteine (NAC). High performance liquid chromatography (HPLC) and liquid chromatography-mass spectrometry (LC-MS) analysis showed that chemical binding of NAC and DMAE-CB occurred in a time dependent manner. Pre-incubation of fourty-eight hours is required for adequate reaction between DMAE-CB and NAC. DMAE-CB reduced human dental pulp cells (hDPCs) viability in a dose-dependent manner. The toxic effects of DMAE-CB were accompanied by increased reactive oxygen species (ROS) level and reduced glutathione (GSH) content. NAC alleviated DMAE-CB-induced oxidative stress. Annexin V/ Propidium Iodide (PI) staining and Hoechst 33342 staining indicated that DMAE-CB induced apoptosis. Collapsed mitochondrial membrane potential (MMP) and activation of caspase-3 were also observed after DMAE-CB treatment. NAC rescued hDPCs from DMAE-CB-induced apoptosis, accompanied by lower level of MMP loss and caspase-3 activity. This study assists to elucidate the mechanism underlying the cytotoxic effects of DMAE-CB and provides theoretical supports for the searching of effective strategies to reduce toxicity of quaternary ammonium dental monomers.

  15. Monthly variations in nitrogen isotopes of ammonium and nitrate in wet deposition at Guangzhou, south China

    Science.gov (United States)

    Jia, Guodong; Chen, Fajin

    2010-06-01

    Monthly nitrogen isotopes of ammonium and nitrate in wet deposition in the city of Guangzhou, and the causes of their variability, are reported in this paper. Nitrate δ 15N showed nearly constant values around zero in the dry season (October to April), but oscillating values from negative to positive in the rainy season (May to September). By contrast, ammonium δ 15N displayed lower values during the rainy season than in the dry season. The rural area north of the city was considered as the prominent source of ammonium and nitrate in spring and early summer (May and June), as suggested by their concurrent negative isotopic trends and higher NH 4+/NO 3- ratios. From July to September, different dominating sources from the city, i.e., fossil fuel combustion for nitrate, and sewage and waste emission for ammonium, caused disparate δ 15N trends of the two species, showing positive nitrate δ 15N, but still negative ammonium δ 15N. During the cool dry season, the high values of ammonium δ 15N and concurrently low NH 4+/NO 3- ratios suggested the decrease in NH 3 volatilization and relatively important thermogenic origin of ammonium, but the intermediate nitrate δ 15N values around zero may be a result of a balanced emission of NO x from the city and the rural areas. The isotopic effects of chemical conversion of NO x to nitrate and washout of nitrate were ruled out as significant causes of nitrate δ 15N variability, but ammonium washout, during which 15N is assumed to be preferentially removed, may partly contribute to the ammonium δ 15N variability.

  16. Mild and Highly Efficient Method for Synthesis of14-Aryl(alkyl)-14H-dibenzo[a,j]xanthenes and1,8-Dioxooctahydroxanthene Derivatives Using Pentafluorophenyl Ammonium Triflate as a Novel Organocatalyst%Mild and Highly Efficient Method for Synthesis of 14-Aryl(alkyl)-14H-dibenzo[a,j]xanthenes and 1,8-Dioxooctahydroxanthene Derivatives Using Pentafluorophenyl Ammonium Triflate as a Novel Organocatalyst

    Institute of Scientific and Technical Information of China (English)

    Samad KHAKSAR; Nosratollah BEHZADI

    2012-01-01

    A simple and facile synthesis of 14-aryl and alkyl-14H-dibenzo[a,j]xanthenes and 1,8-dioxooctahydroxanthene derivatives has been successfully developed by treatment ofβ-naphthol or dimedone with aldehydes under mild conditions in the presence of a pentafluorophenyl ammonium triflate (PFPAT) organocatalyst.These catalytic condensation reactions represent green chemical processes and the PFPAT organocatalyst is air-stable,cost-effective,easy to handle,and easily removed from the reaction mixtures.

  17. Ammonium excretion and oxygen respiration of tropical copepods and euphausiids exposed to oxygen minimum zone conditions

    Science.gov (United States)

    Kiko, Rainer; Hauss, Helena; Buchholz, Friedrich; Melzner, Frank

    2016-04-01

    E. gibboides (Q10, respiration = 2.0; Q10, NH4-excretion = 2.4; E. mucronata not tested). Exposure to differing carbon dioxide levels had no overall significant impact on the respiration or excretion rates. Species from the ETNA were less tolerant to low oxygen levels than E. mucronata from the ETSP, which survived exposure to anoxia at 13 °C. Respiration and excretion rates were reduced upon exposure to low oxygen levels, albeit at different species-specific levels. Reduction of the excretion and respiration rates in ETNA species occurred at a pO2 of 0.6 (P. abdominalis) and 2.4 kPa (U. vulgaris and E. gibboides) at OMZ temperatures. Such low oxygen levels are normally not encountered by these species in the ETNA. E. mucronata however regularly migrates into the strongly hypoxic to anoxic core of the ETSP OMZ. Exposure to low oxygen levels led to a strong reduction of respiration and ammonium excretion in E. mucronata (pcrit respiration = 0.6, pcrit NH4-excretion = 0.73). A drastic reduction of respiratory activity was also observed by other authors for euphausiids, squat lobsters and calanoid copepods, but was not yet accounted for when calculating DVM-mediated active fluxes into the ETSP OMZ. Current estimates of DVM-mediated active export of carbon and nitrogen into the ETSP OMZ are therefore likely too high and future efforts to calculate these export rates should take the physiological responses of migratory species to OMZ conditions into account.

  18. Salivary fluoride levels after use of high-fluoride dentifrice.

    Science.gov (United States)

    Vale, Glauber Campos; Cruz, Priscila Figueiredo; Bohn, Ana Clarissa Cavalcante Elvas; de Moura, Marcoeli Silva

    2015-01-01

    The aim of the study was to evaluate salivary fluoride (F) availability after toothbrushing with a high-F dentifrice. Twelve adult volunteers took part in this crossover and blind study. F concentration in saliva was determined after brushing with a high-F dentifrice (5000 µg F/g) or with a conventional F concentration dentifrice (1100 µg F/g) followed by a 15 mL distilled water rinse. Samples of nonstimulated saliva were collected on the following times: before (baseline), and immediately after spit (time = 0) and after 1, 2, 3, 4, 5, 10, 15, 20, 30, 45, 60, 90, and 120 min. F analysis was performed with a fluoride-sensitive electrode and the area under curve of F salivary concentration × time (µg F/mL × min(-1)) was calculated. At baseline, no significant difference was found among dentifrices (P > 0.05). After brushing, both dentifrices caused an elevated fluoride level in saliva; however salivary F concentration was significantly higher at all times, when high-F dentifrice was used (P dentifrices (P dentifrice enhanced the bioavailability of salivary F, being an option for caries management in patients with high caries risk.

  19. The CMS High Level Trigger System: Experience and Future Development

    CERN Document Server

    Bauer, Gerry; Bowen, Matthew; Branson, James G; Bukowiec, Sebastian; Cittolin, Sergio; Coarasa, J A; Deldicque, Christian; Dobson, Marc; Dupont, Aymeric; Erhan, Samim; Flossdorf, Alexander; Gigi, Dominique; Glege, Frank; Gomez-Reino, R; Hartl, Christian; Hegeman, Jeroen; Holzner, André; Y L Hwong; Masetti, Lorenzo; Meijers, Frans; Meschi, Emilio; Mommsen, R K; O'Dell, Vivian; Orsini, Luciano; Paus, Christoph; Petrucci, Andrea; Pieri, Marco; Polese, Giovanni; Racz, Attila; Raginel, Olivier; Sakulin, Hannes; Sani, Matteo; Schwick, Christoph; Shpakov, Dennis; Simon, M; Spataru, A C; Sumorok, Konstanty

    2012-01-01

    The CMS experiment at the LHC features a two-level trigger system. Events accepted by the first level trigger, at a maximum rate of 100 kHz, are read out by the Data Acquisition system (DAQ), and subsequently assembled in memory in a farm of computers running a software high-level trigger (HLT), which selects interesting events for offline storage and analysis at a rate of order few hundred Hz. The HLT algorithms consist of sequences of offline-style reconstruction and filtering modules, executed on a farm of 0(10000) CPU cores built from commodity hardware. Experience from the operation of the HLT system in the collider run 2010/2011 is reported. The current architecture of the CMS HLT, its integration with the CMS reconstruction framework and the CMS DAQ, are discussed in the light of future development. The possible short- and medium-term evolution of the HLT software infrastructure to support extensions of the HLT computing power, and to address remaining performance and maintenance issues, are discussed.

  20. Interface Engineering of Metal Oxides using Ammonium Anthracene in Inverted Organic Solar Cells.

    Science.gov (United States)

    Jeon, Il; Zeljkovic, Sasa; Kondo, Kei; Yoshizawa, Michito; Matsuo, Yutaka

    2016-11-09

    In this work, by casting water-soluble ammonium anthracene on metal oxides, the organic surface modifier re-engineered the interface of the metal oxide to improve charge transport. The energy level of ammonium anthracene increased the work function of indium tin oxide (ITO), functioning as a hole-blocker (electron-transporter). Solar cells in which ITO was treated by the ammonium anthracene produced an average power conversion efficiency (PCE) of 5.8% without ZnO, the electron-transporting layer. When the ammonium anthracene was applied to ZnO, an average PCE of 8.1% was achieved, which is higher than the average PCE of 7.5% for nontreated ZnO-based devices.

  1. A phenomenological model for improving understanding of the ammonium nitrate agglomeration process

    Directory of Open Access Journals (Sweden)

    Videla Leiva Alvaro

    2016-01-01

    Full Text Available Ammonium nitrate is intensively used as explosive in the mining industry as the main component of ANFO. The ammonium nitrate is known to be a strong hygroscopic crystal matter which generates problems due to the creation of water bridges between crystals leading later to nucleation and crystallization forming an agglomerated solid cake. The agglomeration process damages the ammonium nitrate performance and is undesirable. Usually either organic or inorganic coatings are used to control agglomeration. In the present work a characterization method of humidity adsorption of the ammonium nitrate crystal was performed under laboratory conditions. Several samples were exposed into a defined humidity in a controlled chamber during 5 hours after which the samples were tested to measure agglomeration as the resistance force to compression. A clear relation was found between coating protection level, humidity and agglomeration. Agglomeration can be then predicted by a phenomenological model based of combination of the mono-layer BET adsorption and CNT nucleation models.

  2. Spent fuel and high-level radioactive waste transportation report

    Energy Technology Data Exchange (ETDEWEB)

    1990-11-01

    This publication is intended to provide its readers with an introduction to the issues surrounding the subject of transportation of spent nuclear fuel and high-level radioactive waste, especially as those issues impact the southern region of the United States. It was originally issued by the Southern States Energy Board (SSEB) in July 1987 as the Spent Nuclear Fuel and High-Level Radioactive Waste Transportation Primer, a document patterned on work performed by the Western Interstate Energy Board and designed as a ``comprehensive overview of the issues.`` This work differs from that earlier effort in that it is designed for the educated layman with little or no background in nuclear waste issues. In addition, this document is not a comprehensive examination of nuclear waste issues but should instead serve as a general introduction to the subject. Owing to changes in the nuclear waste management system, program activities by the US Department of Energy and other federal agencies and developing technologies, much of this information is dated quickly. While this report uses the most recent data available, readers should keep in mind that some of the material is subject to rapid change. SSEB plans periodic updates in the future to account for changes in the program. Replacement pages will be supplied to all parties in receipt of this publication provided they remain on the SSEB mailing list.

  3. Evaluation and selection of candidate high-level waste forms

    Energy Technology Data Exchange (ETDEWEB)

    Bernadzikowski, T. A.; Allender, J. S.; Butler, J. L.; Gordon, D. E.; Gould, Jr., T. H.; Stone, J. A.

    1982-03-01

    Seven candidate waste forms being developed under the direction of the Department of Energy's National High-Level Waste (HLW) Technology Program, were evaluated as potential media for the immobilization and geologic disposal of high-level nuclear wastes. The evaluation combined preliminary waste form evaluations conducted at DOE defense waste-sites and independent laboratories, peer review assessments, a product performance evaluation, and a processability analysis. Based on the combined results of these four inputs, two of the seven forms, borosilicate glass and a titanate based ceramic, SYNROC, were selected as the reference and alternative forms for continued development and evaluation in the National HLW Program. Both the glass and ceramic forms are viable candidates for use at each of the DOE defense waste-sites; they are also potential candidates for immobilization of commercial reprocessing wastes. This report describes the waste form screening process, and discusses each of the four major inputs considered in the selection of the two forms.

  4. Burning high-level TRU waste in fusion fission reactors

    Science.gov (United States)

    Shen, Yaosong

    2016-09-01

    Recently, the concept of actinide burning instead of a once-through fuel cycle for disposing spent nuclear fuel seems to get much more attention. A new method of burning high-level transuranic (TRU) waste combined with Thorium-Uranium (Th-U) fuel in the subcritical reactors driven by external fusion neutron sources is proposed in this paper. The thorium-based TRU fuel burns all of the long-lived actinides via a hard neutron spectrum while outputting power. A one-dimensional model of the reactor concept was built by means of the ONESN_BURN code with new data libraries. The numerical results included actinide radioactivity, biological hazard potential, and much higher burnup rate of high-level transuranic waste. The comparison of the fusion-fission reactor with the thermal reactor shows that the harder neutron spectrum is more efficient than the soft. The Th-U cycle produces less TRU, less radiotoxicity and fewer long-lived actinides. The Th-U cycle provides breeding of 233U with a long operation time (>20 years), hence significantly reducing the reactivity swing while improving safety and burnup.

  5. Spent Fuel and High-Level Radioactive Waste Transportation Report

    Energy Technology Data Exchange (ETDEWEB)

    1992-03-01

    This publication is intended to provide its readers with an introduction to the issues surrounding the subject of transportation of spent nuclear fuel and high-level radioactive waste, especially as those issues impact the southern region of the United States. It was originally issued by SSEB in July 1987 as the Spent Nuclear Fuel and High-Level Radioactive Waste Transportation Primer, a document patterned on work performed by the Western Interstate Energy Board and designed as a ``comprehensive overview of the issues.`` This work differs from that earlier effort in that it is designed for the educated layman with little or no background in nuclear waste Issues. In addition. this document is not a comprehensive examination of nuclear waste issues but should instead serve as a general introduction to the subject. Owing to changes in the nuclear waste management system, program activities by the US Department of Energy and other federal agencies and developing technologies, much of this information is dated quickly. While this report uses the most recent data available, readers should keep in mind that some of the material is subject to rapid change. SSEB plans periodic updates in the future to account for changes in the program. Replacement pages will be supplied to all parties in receipt of this publication provided they remain on the SSEB mailing list.

  6. High-level expressing YAC vector for transgenic animal bioreactors.

    Science.gov (United States)

    Fujiwara, Y; Miwa, M; Takahashi, R; Kodaira, K; Hirabayashi, M; Suzuki, T; Ueda, M

    1999-04-01

    The position effect is one major problem in the production of transgenic animals as mammary gland bioreactors. In the present study, we introduced the human growth hormone (hGH) gene into 210-kb human alpha-lactalbumin position-independent YAC vectors using homologous recombination and produced transgenic rats via microinjection of YAC DNA into rat embryos. The efficiency of producing transgenic rats with the YAC vector DNA was the same as that using plasmid constructs. All analyzed transgenic rats had one copy of the transgene and produced milk containing a high level of hGH (0.25-8.9 mg/ml). In transgenic rats with the YAC vector in which the human alpha-lactalbumin gene was replaced with the hGH gene, tissue specificity of hGH mRNA was the same as that of the endogenous rat alpha-lactalbumin gene. Thus, the 210-kb human alpha-lactalbumin YAC is a useful vector for high-level expression of foreign genes in the milk of transgenic animals.

  7. ATW system impact on high-level waste

    Energy Technology Data Exchange (ETDEWEB)

    Arthur, E.D.

    1992-12-01

    This report discusses the Accelerator Transmutation of Waste (ATW) concept which aims at destruction of key long-lived radionuclides in high-level nuclear waste (HLW), both fission products and actinides. This focus makes it different from most other transmutation concepts which concentrate primarily on actinide burning. The ATW system uses an accelerator-driven, sub-critical assembly to create an intense thermal neutron environment for radionuclide transmutation. This feature allows rapid transmutation under low-inventory system conditions, which in turn, has a direct impact on the size of chemical separations and materials handling components of the system. Inventories in ATW are factors of eight to thirty times smaller than reactor systems of equivalent thermal power. Chemical separations systems are relatively small in scale and can be optimized to achieve high decontamination factors and minimized waste streams. The low-inventory feature also directly impacts material amounts remaining in the system at its end of life. In addition to its low-inventory operation, the accelerator-driven neutron source features of ATW are key to providing a sufficient level of neutrons to allow transmutation of long-lived fission products.

  8. Spent fuel and high-level radioactive waste transportation report

    Energy Technology Data Exchange (ETDEWEB)

    1989-11-01

    This publication is intended to provide its readers with an introduction to the issues surrounding the subject of transportation of spent nuclear fuel and high-level radioactive waste, especially as those issues impact the southern region of the United States. It was originally issued by the Southern States Energy Board (SSEB) in July 1987 as the Spent Nuclear Fuel and High-Level Radioactive Waste Transportation Primer, a document patterned on work performed by the Western Interstate Energy Board and designed as a ``comprehensive overview of the issues.`` This work differs from that earlier effort in that it is designed for the educated layman with little or no background in nuclear waste issues. In addition, this document is not a comprehensive examination of nuclear waste issues but should instead serve as a general introduction to the subject. Owing to changes in the nuclear waste management system, program activities by the US Department of Energy and other federal agencies and developing technologies, much of this information is dated quickly. While this report uses the most recent data available, readers should keep in mind that some of the material is subject to rapid change. SSEB plans periodic updates in the future to account for changes in the program. Replacement pages sew be supplied to all parties in receipt of this publication provided they remain on the SSEB mailing list.

  9. VITRIFICATION OF HIGH LEVEL WASTE AT THE SAVANNAH RIVER SITE

    Energy Technology Data Exchange (ETDEWEB)

    Fox, K.; Peeler, D.

    2009-06-17

    The objective of this study was to experimentally measure the properties and performance of a series of glasses with compositions that could represent high level waste Sludge Batch 5 (SB5) as vitrified at the Savannah River Site Defense Waste Processing Facility. These data were used to guide frit optimization efforts as the SB5 composition was finalized. Glass compositions for this study were developed by combining a series of SB5 composition projections with a group of candidate frits. The study glasses were fabricated using depleted uranium and their chemical compositions, crystalline contents and chemical durabilities were characterized. Trevorite was the only crystalline phase that was identified in a few of the study glasses after slow cooling, and is not of concern as spinels have been shown to have little impact on the durability of high level waste glasses. Chemical durability was quantified using the Product Consistency Test (PCT). All of the glasses had very acceptable durability performance. The results of this study indicate that a frit composition can be identified that will provide a processable and durable glass when combined with SB5.

  10. Studies of ATM for ATLAS high level triggers

    CERN Document Server

    Bystrický, J; Huet, M; Le Dû, P; Mandjavidze, I D

    2001-01-01

    This paper presents some of the conclusions of our studies on ATM and Fast Ethernet in the ATLAS level-2 trigger Pilot project. We describe the general concept and principles of our data collection and event building scheme that could be transposed to various experiments in high energy and nuclear physics. To validate the approach in view of ATLAS High Level Triggers, we assembled a testbed composed of up to 48 computers linked by a 7.5 Gbit/s ATM switch. This modular switch is used as a single entity or is split into several smaller interconnected switches. This allows studying how to construct a large network from smaller units. Alternatively, the ATM network can be replaced by Fast Ethernet. We detail the operation of the system and present series of performance measurements made with event building traffic pattern. We extrapolate these results to show how today's commercial networking components could be used to build a 1000-port network adequate for ATLAS needs. Finally, we list the benefits and the limi...

  11. Studies of ATM for ATLAS high-level triggers

    CERN Document Server

    Bystrický, J; Huet, M; Le Dû, P; Mandjavidze, I D

    2001-01-01

    This paper presents some of the conclusions of our studies on asynchronous transfer mode (ATM) and fast Ethernet in the ATLAS level-2 trigger pilot project. We describe the general concept and principles of our data-collection and event-building scheme that could be transposed to various experiments in high-energy and nuclear physics. To validate the approach in view of ATLAS high-level triggers, we assembled a testbed composed of up to 48 computers linked by a 7.5-Gbit/s ATM switch. This modular switch is used as a single entity or is split into several smaller interconnected switches. This allows study of how to construct a large network from smaller units. Alternatively, the ATM network can be replaced by fast Ethernet. We detail the operation of the system and present series of performance measurements made with event-building traffic pattern. We extrapolate these results to show how today's commercial networking components could be used to build a 1000-port network adequate for ATLAS needs. Lastly, we li...

  12. High-level microsatellite instability in appendiceal carcinomas.

    Science.gov (United States)

    Taggart, Melissa W; Galbincea, John; Mansfield, Paul F; Fournier, Keith F; Royal, Richard E; Overman, Michael J; Rashid, Asif; Abraham, Susan C

    2013-08-01

    High-level microsatellite instability (MSI-high) is found in approximately 15% of all colorectal adenocarcinomas (CRCs) and in at least 20% of right-sided cancers. It is most commonly due to somatic hypermethylation of the MLH1 gene promoter region, with familial cases (Lynch syndrome) representing only 2% to 3% of CRCs overall. In contrast to CRC, MSI-high in appendiceal adenocarcinomas is rare. Only 4 MSI-high appendiceal carcinomas and 1 MSI-high appendiceal serrated adenoma have been previously reported, and the prevalence of MSI in the appendix is unknown. We identified 108 appendiceal carcinomas from MD Anderson Cancer Center in which MSI status had been assessed by immunohistochemistry for the DNA mismatch-repair proteins MLH1, MSH2, MSH6, and PMS2 (n=83), polymerase chain reaction (n=7), or both (n=18). Three cases (2.8%) were MSI-high, and 1 was MSI-low. The 3 MSI-high cases included: (1) a poorly differentiated nonmucinous adenocarcinoma with loss of MLH1/PMS2 expression, lack of MLH1 promoter methylation, and lack of BRAF gene mutation, but no detected germline mutation in MLH1 from a 39-year-old man; (2) an undifferentiated carcinoma with loss of MSH2/MSH6, but no detected germline mutation in MSH2 or TACSTD1, from a 59-year-old woman; and (3) a moderately differentiated mucinous adenocarcinoma arising in a villous adenoma with loss of MSH2/MSH6 expression, in a 38-year-old man with a strong family history of CRC who declined germline testing. When the overall group of appendiceal carcinomas was classified according to histologic features and precursor lesions, the frequencies of MSI-high were: 3 of 108 (2.8%) invasive carcinomas, 3 of 96 (3.1%) invasive carcinomas that did not arise from a background of goblet cell carcinoid tumors, and 0 of 12 (0%) signet ring and mucinous carcinomas arising in goblet cell carcinoid tumors. These findings, in conjunction with the previously reported MSI-high appendiceal carcinomas, highlight the low prevalence of MSI

  13. Structural basis for Mep2 ammonium transceptor activation by phosphorylation.

    Science.gov (United States)

    van den Berg, Bert; Chembath, Anupama; Jefferies, Damien; Basle, Arnaud; Khalid, Syma; Rutherford, Julian C

    2016-04-18

    Mep2 proteins are fungal transceptors that play an important role as ammonium sensors in fungal development. Mep2 activity is tightly regulated by phosphorylation, but how this is achieved at the molecular level is not clear. Here we report X-ray crystal structures of the Mep2 orthologues from Saccharomyces cerevisiae and Candida albicans and show that under nitrogen-sufficient conditions the transporters are not phosphorylated and present in closed, inactive conformations. Relative to the open bacterial ammonium transporters, non-phosphorylated Mep2 exhibits shifts in cytoplasmic loops and the C-terminal region (CTR) to occlude the cytoplasmic exit of the channel and to interact with His2 of the twin-His motif. The phosphorylation site in the CTR is solvent accessible and located in a negatively charged pocket ∼30 Å away from the channel exit. The crystal structure of phosphorylation-mimicking Mep2 variants from C. albicans show large conformational changes in a conserved and functionally important region of the CTR. The results allow us to propose a model for regulation of eukaryotic ammonium transport by phosphorylation.

  14. Engineering neural systems for high-level problem solving.

    Science.gov (United States)

    Sylvester, Jared; Reggia, James

    2016-07-01

    There is a long-standing, sometimes contentious debate in AI concerning the relative merits of a symbolic, top-down approach vs. a neural, bottom-up approach to engineering intelligent machine behaviors. While neurocomputational methods excel at lower-level cognitive tasks (incremental learning for pattern classification, low-level sensorimotor control, fault tolerance and processing of noisy data, etc.), they are largely non-competitive with top-down symbolic methods for tasks involving high-level cognitive problem solving (goal-directed reasoning, metacognition, planning, etc.). Here we take a step towards addressing this limitation by developing a purely neural framework named galis. Our goal in this work is to integrate top-down (non-symbolic) control of a neural network system with more traditional bottom-up neural computations. galis is based on attractor networks that can be "programmed" with temporal sequences of hand-crafted instructions that control problem solving by gating the activity retention of, communication between, and learning done by other neural networks. We demonstrate the effectiveness of this approach by showing that it can be applied successfully to solve sequential card matching problems, using both human performance and a top-down symbolic algorithm as experimental controls. Solving this kind of problem makes use of top-down attention control and the binding together of visual features in ways that are easy for symbolic AI systems but not for neural networks to achieve. Our model can not only be instructed on how to solve card matching problems successfully, but its performance also qualitatively (and sometimes quantitatively) matches the performance of both human subjects that we had perform the same task and the top-down symbolic algorithm that we used as an experimental control. We conclude that the core principles underlying the galis framework provide a promising approach to engineering purely neurocomputational systems for problem

  15. Calcium sulphate in ammonium sulphate solution

    Science.gov (United States)

    Sullivan, E.C.

    1905-01-01

    Calcium sulphate, at 25?? C., is two-thirds as soluble in dilute (o.i mol per liter) and twice as soluble in concentrated (3 mois per liter) ammonium sulphate solution as in water. The specific electric conductivity of concentrated ammonium sulphate solutions is lessened by saturating with calcium sulphate. Assuming that dissociation of ammonium sulphate takes place into 2NH4?? and SO4" and of calcium sulphate into Ca and SO4" only, and that the conductivity is a measure of such dissociation, the solubility of calcium sulphate in dilute ammonium sulphate solutions is greater than required by the mass-law. The conductivity of the dilute mixtures may be accurately calculated by means of Arrhenius' principle of isohydric solutions. In the data obtained in these calculations, the concentration of non-dissociated calcium sulphate decreases with increasing ammonium sulphate. The work as a whole is additional evidence of the fact that we are not yet in possession of all the factors necessary for reconciling the mass-law to the behavior of electrolytes. The measurements above described were made in the chemical laboratory of the University of Michigan.

  16. Myocytes oxygenation and high energy phosphate levels during hypoxia.

    Directory of Open Access Journals (Sweden)

    Mohammad Nurulqadr Jameel

    Full Text Available Decrease of ambient oxygen level has been used in myocytes culture experiments in examining the responsiveness to stress secondary to hypoxia. However, none of these studies measure the myocytes oxygenation levels resulting in ambiguity as to whether there is insufficient oxygen delivery. This study examined the hypothesis that at a basal myocardial work state, adequate myocyte oxygenation would be maintained until extremely low arterial pO2 levels were reached. Myocyte pO2 values in normal dogs were calculated from the myocardial deoxymyoglobin (Mb- δ levels using (1H-spectroscopy (MRS and were normalized to Mb-δ obtained after complete LAD occlusion. During Protocol 1 (n = 6, Mb-δ was measured during sequential reductions of the oxygen fraction of inspired gas (FIO2 from 40, 21, 15, 10, and 5%, while in protocol 2 (n = 10 Mb-δ was measured at FIO2 of 3%. Protocol 3 (n = 9 evaluated time course of Mb-δ during prolonged exposure to FIO2 of 5%. Myocardial blood flow (MBF was measured with microspheres and high energy phosphate (HEP levels were determined with (31P-MRS. MVO2 progressively increased in response to the progressive reduction of FIO2 that is accompanied by increased LV pressure, heart rate, and MBF. Mb-δ was undetectable during FIO2 values of 21, 15, 10, and 5%. However, FIO2 of 3% or prolonged exposure to FIO2 of 5% caused progressive increases of Mb-δ which were associated with decreases of PCr, ATP and the PCr/ATP ratio, as well as increases of inorganic phosphate. The intracellular PO2 values for 20% reductions of PCr and ATP were approximately 7.4 and 1.9 mmHg, respectively. These data demonstrate that in the in vivo system over a wide range of FIO2 and arterial pO2 levels, the myocyte pO2 values remain well above the K(m value with respect to cytochrome oxidase, and oxygen availability does not limit mitochondrial oxidative phosphorylation at 5% FIO2.

  17. Proton- and ammonium- sensing by histaminergic neurons controlling wakefulness.

    Directory of Open Access Journals (Sweden)

    Yvgenij eYanovsky

    2012-04-01

    Full Text Available Orexinergic and histaminergic neurons in the posterior hypothalamus are involved in the control of arousal. Extracellular levels of acid /CO2 are fundamental physicochemical signals controlling wakefulness and breathing. Acidification excites orexinergic neurons like the chemosensory neurons in the brain stem. Hypercapnia induces c-Fos expression, a marker for increased neuronal activity, in the rat histaminergic tuberomamillary nucleus (TMN, but the mechanisms of this excitation are unknown. Acid-sensing ion channels (ASICs are gated by protons and also by ammonium. Recordings in rat brain slices revealed now that acidification within the physiological range (pH from 7.3 to 7.0 as well as ammonium chloride (5mM excite histaminergic neurons. We detected variable combinations of 4 known types of ASICs in single TMN neurons, along with the pharmacological properties of pH-induced current. At pH 7.0 however, activation of ASICs in TMN neurons was negligible. Block of type I metabotropic glutamate receptors abolished proton- but not ammonium- induced excitation. Mouse TMN neurons were identified within a novel HDC-Cre transgenic reporter mouse line. In contrast to the rat these lacked pH 7.0-induced excitation and showed only a minimal response to the mGluR I agonist DHPG (0.5µM. Ammonium-induced excitation was similar in mouse and rat. Thus glutamate, which is released by glial cells and orexinergic axons amplifies CO2/acid-induced arousal through the recruitment of the histaminergic system in rat but not in mouse. These results are relevant for the understanding of neuronal mechanisms controlling H+/CO2-induced arousal in hepatic encephalopathy and obstructive sleep apnoea. The new HDC-Cre mouse model will be a useful tool for studying the physiological and pathophysiological roles of the histaminergic system.

  18. NUTRITION OF MATE-TREE WITH AMMONIUM SULFATE FERTILIZER

    Directory of Open Access Journals (Sweden)

    Marcia Marzagão Ribeiro

    2008-09-01

    Full Text Available Mate tea leaves are the product of commercialization of the mate-tea tree (Ilex paraguariensis St. Hil., which leads to a great export of N, requiring its reposition. In previous nutritional studies of the mate-tea tree, it was observed that its production and metabolism was positively influenced by the ammonium form nitrogen fertilizer. This investigation tested different levels of nitrogen fertilization, in its ammonium form, in a commercial plantation, for verifying its effects on the nutritional status and on the productivity. The experiment was assembled in the region of Ivaí - Paraná, using, as fertilizer, the ammonium sulfate in the dosages of 00, 40, 60, 80 kg N ha-1. The statistical design was randomized blocks, with a split-plot arrangement, consisting of four treatments, two evaluation seasons with five replications and twenty plants per plot, being laid out in a 2,0 m x 3,5 m spacing. The evaluation of the plant’s nutritional status was performed through foliar analysis total N, K, P, Ca, Mg, Fe, Mn, Cu, Zn and Al, in winter and summer, with fertilizations performed for two years. It was concluded that nitrogen supplied in the form of ammonium sulfate has a positive influence on the biomass up to the rate of 52,5 kg N ha-1. The harvesting season influences the plant’s chemical composition. The fertilization significantly influences the foliar contents of N, K and Mg and Zn during winter and Fe, Cu e Al during summer.

  19. Determination of ammonium and organic bound nitrogen by inductively coupled plasma emission spectroscopy.

    Science.gov (United States)

    Jaber, A M Y; Mehanna, N A; Sultan, S M

    2009-06-15

    The continuous flow sample introduction technique with a hydride generator system in conjunction with an inductively coupled plasma emission spectrometer (ICP-AES-HG), is used in this study for quantitative determination of ammonium and organic bound nitrogen in aqueous and solid samples. Ammonia vapor released from ammonium salt after treatment with concentrated NaOH is transferred by argon to plasma for detection at 174.273 nm using axial argon plasma mode. The calibration curves were linear within a range of 25-1000 mg L(-1)N as ammonium molybdate with correlation coefficients of better than 0.99 and limits of detection of about 10-25mg L(-1)N. The percent recovery of N (25-500 mg L(-1)N) in soft (distilled) water and high salt content (1.7 mol L(-1) NaCl) matrices was found to be in the range of about 97-102% with %RSD in the range of 4.6-0.62. The sensitivity, limit of detection, and blank contribution from the atmospheric nitrogen, were tremendously improved in this method compared with the available ICP-AES spray chamber counterpart. Furthermore, the ICP-AES-HG method gave results for real samples (soil, fertilizer, waste water) containing about 50-1800 mg L(-1)N in good agreement with those obtained by the standard Kjeldahl method. No statistical differences at the 95% confidence level on applying the t-test were observed between the values obtained by the two methods. Thus, the ICP-AES-HG method is reliable and faster than the conventional tedious Kjeldahl method, superior to the ICP-AES spray chamber method, and almost free from matrix interference which is usually a critical factor in atomic emission spectroscopic techniques.

  20. High-Voltage-Input Level Translator Using Standard CMOS

    Science.gov (United States)

    Yager, Jeremy A.; Mojarradi, Mohammad M.; Vo, Tuan A.; Blalock, Benjamin J.

    2011-01-01

    proposed integrated circuit would translate (1) a pair of input signals having a low differential potential and a possibly high common-mode potential into (2) a pair of output signals having the same low differential potential and a low common-mode potential. As used here, "low" and "high" refer to potentials that are, respectively, below or above the nominal supply potential (3.3 V) at which standard complementary metal oxide/semiconductor (CMOS) integrated circuits are designed to operate. The input common-mode potential could lie between 0 and 10 V; the output common-mode potential would be 2 V. This translation would make it possible to process the pair of signals by use of standard 3.3-V CMOS analog and/or mixed-signal (analog and digital) circuitry on the same integrated-circuit chip. A schematic of the circuit is shown in the figure. Standard 3.3-V CMOS circuitry cannot withstand input potentials greater than about 4 V. However, there are many applications that involve low-differential-potential, high-common-mode-potential input signal pairs and in which standard 3.3-V CMOS circuitry, which is relatively inexpensive, would be the most appropriate circuitry for performing other functions on the integrated-circuit chip that handles the high-potential input signals. Thus, there is a need to combine high-voltage input circuitry with standard low-voltage CMOS circuitry on the same integrated-circuit chip. The proposed circuit would satisfy this need. In the proposed circuit, the input signals would be coupled into both a level-shifting pair and a common-mode-sensing pair of CMOS transistors. The output of the level-shifting pair would be fed as input to a differential pair of transistors. The resulting differential current output would pass through six standoff transistors to be mirrored into an output branch by four heterojunction bipolar transistors. The mirrored differential current would be converted back to potential by a pair of diode-connected transistors

  1. The ammonium nitrate and its mechanism of decomposition in the gas phase: a theoretical study and a DFT benchmark.

    Science.gov (United States)

    Cagnina, Stefania; Rotureau, Patricia; Fayet, Guillaume; Adamo, Carlo

    2013-07-14

    The decomposition mechanism of ammonium nitrate in the gas phase was investigated and fully characterized by means of CBS-QB3 calculations. Five reaction channels were identified, leading to the formation of products (N2, H2O, O2, OH, HNO, NO3) found in the experimental works. The identified mechanism well underlines the origin of the chemical hazard of ammonium nitrate which is related to the exothermicity of the lowest decomposition channels. Furthermore, the high barrier to overcome in the rate determining step well explained the fact that the reaction is not usually spontaneous and requires a significant external stimulus for its onset. An accurate DFT benchmark study was then conducted to determine the most suitable exchange-correlation functional to accurately describe the reaction profile both in terms of structures and thermochemistry. This evaluation supports the use of the M06-2X functional as the best option for the study of ammonium nitrate decomposition and related reactions. Indeed, this level of theory provided the lowest deviations with respect to CBS-QB3 reference values, outperforming functionals especially developed for reaction kinetics.

  2. High-level fluorescence labeling of gram-positive pathogens.

    Directory of Open Access Journals (Sweden)

    Simone Aymanns

    Full Text Available Fluorescence labeling of bacterial pathogens has a broad range of interesting applications including the observation of living bacteria within host cells. We constructed a novel vector based on the E. coli streptococcal shuttle plasmid pAT28 that can propagate in numerous bacterial species from different genera. The plasmid harbors a promoterless copy of the green fluorescent variant gene egfp under the control of the CAMP-factor gene (cfb promoter of Streptococcus agalactiae and was designated pBSU101. Upon transfer of the plasmid into streptococci, the bacteria show a distinct and easily detectable fluorescence using a standard fluorescence microscope and quantification by FACS-analysis demonstrated values that were 10-50 times increased over the respective controls. To assess the suitability of the construct for high efficiency fluorescence labeling in different gram-positive pathogens, numerous species were transformed. We successfully labeled Streptococcus pyogenes, Streptococcus agalactiae, Streptococcus dysgalactiae subsp. equisimilis, Enterococcus faecalis, Enterococcus faecium, Streptococcus mutans, Streptococcus anginosus and Staphylococcus aureus strains utilizing the EGFP reporter plasmid pBSU101. In all of these species the presence of the cfb promoter construct resulted in high-level EGFP expression that could be further increased by growing the streptococcal and enterococcal cultures under high oxygen conditions through continuous aeration.

  3. Reduction in Ammonium Ions in Sludge Liquor

    Directory of Open Access Journals (Sweden)

    Eglė Šlajūtė

    2013-12-01

    Full Text Available Liquor rejected from the centrifugation of the digested sludge can contain the concentrations of ammonium ions up to 1750 mg/L. These loads are usually returned to the intake of wastewater treatment plants (WWTP without additional treatment and can have a negative impact on biological wastewater and/or sludge treatment processes, e.g. phosphorus and nitrogen removal. This article deals with the use of naturally obtained sorbent, zeolite, in batch and column test procedure for removing ammonium from the rejected liquor. This research study was carried out using different sizes of zeolite particles: 0.8–1.6 mm and 1.6–2.5 mm. The highest efficiency of ammonium removal (up to 98 % was achieved by applying the zeolite particles of 0.8–1.6 mm.Article in Lithuanian

  4. High-level waste tank farm set point document

    Energy Technology Data Exchange (ETDEWEB)

    Anthony, J.A. III

    1995-01-15

    Setpoints for nuclear safety-related instrumentation are required for actions determined by the design authorization basis. Minimum requirements need to be established for assuring that setpoints are established and held within specified limits. This document establishes the controlling methodology for changing setpoints of all classifications. The instrumentation under consideration involve the transfer, storage, and volume reduction of radioactive liquid waste in the F- and H-Area High-Level Radioactive Waste Tank Farms. The setpoint document will encompass the PROCESS AREA listed in the Safety Analysis Report (SAR) (DPSTSA-200-10 Sup 18) which includes the diversion box HDB-8 facility. In addition to the PROCESS AREAS listed in the SAR, Building 299-H and the Effluent Transfer Facility (ETF) are also included in the scope.

  5. Transmutation of high-level radioactive waste - Perspectives

    CERN Document Server

    Junghans, Arnd; Grosse, Eckart; Hannaske, Roland; Kögler, Toni; Massarczyk, Ralf; Schwengner, Ronald; Wagner, Andreas

    2014-01-01

    In a fast neutron spectrum essentially all long-lived actinides (e.g. Plutonium) undergo fission and thus can be transmuted into generally short lived fission products. Innovative nuclear reactor concepts e.g. accelerator driven systems (ADS) are currently in development that foresee a closed fuel cycle. The majority of the fissile nuclides (uranium, plutonium) shall be used for power generation and only fission products will be put into final disposal that needs to last for a historical time scale of only 1000 years. For the transmutation of high-level radioactive waste a lot of research and development is still required. One aspect is the precise knowledge of nuclear data for reactions with fast neutrons. Nuclear reactions relevant for transmutation are being investigated in the framework of the european project ERINDA. First results from the new neutron time-of-flight facility nELBE at Helmholtz-Zentrum Dresden-Rossendorf will be presented.

  6. Intermittent Testing and Training for High-Level Football Players

    DEFF Research Database (Denmark)

    Ingebrigtsen, Jørgen

    Football is the most popular sport in the world, played by over 400 million men and women. In addition to the wide range of sport-specific technical and tactical skills needed, several physical components have been shown to be necessary to perform at a high level. The present PhD thesis is based...... on four articles that focus on physical testing and training for elite and sub-elite football players.The first article (Study I) aims to identify and establish aerobic capacities and anthropometric characteristics of elite female football players with the use of laboratory tests, and to examine whether...... with other field tests the Yo-Yo IR2 has become an important tool for monitoring the physical fitness of football players. However, the burden of testing, for players (physically and mentally) and the coaching staff (time consuming), is large and there is a probability that the tests may contain overlapping...

  7. High level architecture evolved modular federation object model

    Institute of Scientific and Technical Information of China (English)

    Wang Wenguang; Xu Yongping; Chen Xin; Li Qun; Wang Weiping

    2009-01-01

    To improve the agility, dynamics, composability, reusability, and development efficiency restricted by monolithic federation object model (FOM), a modular FOM is proposed by high level architecture (HLA) evolved product development group. This paper reviews the state-of-the-art of HLA evolved modular FOM. In particular, related concepts, the overall impact on HLA standards, extension principles, and merging processes are discussed. Also permitted and restricted combinations, and merging rules are provided, and the influence on HLA interface specification is given. The comparison between modular FOM and base object model (BOM) is performed to illustrate the importance of their combination. The applications of modular FOM are summarized. Finally, the significance to facilitate compoable simulation both in academia and practice is presented and future directions are pointed out.

  8. High-level theoretical rovibrational spectroscopy of HCS+ isotopologues

    Science.gov (United States)

    Schröder, B.; Sebald, P.

    2016-12-01

    In this work the rovibrational spectrum of the HCS+ molecular cation is revisited through high-level electronic structure and variational rovibrational calculations. A local potential energy function is built from explicitly correlated coupled-cluster results, incorporating corrections for core-valence, scalar relativistic and higher-order excitation effects. The computed spectroscopic parameters, based on variational calculations with Watson's isomorphic Hamiltonian for linear molecules lead to a nearly perfect agreement with experimentally reported values (Rosenbaum et al., 1989). Furthermore, the documented Fermi resonance within the (0,00, 1) / (0,20, 0) and (1,00, 1) / (1,20, 0) pairs of states is clarified. Based on a newly developed electric dipole moment function transition dipole moments of fundamental transitions are predicted for the most important isotopologues.

  9. High Level Waste System Impacts from Acid Dissolution of Sludge

    Energy Technology Data Exchange (ETDEWEB)

    KETUSKY, EDWARD

    2006-04-20

    This research evaluates the ability of OLI{copyright} equilibrium based software to forecast Savannah River Site High Level Waste system impacts from oxalic acid dissolution of Tank 1-15 sludge heels. Without further laboratory and field testing, only the use of oxalic acid can be considered plausible to support sludge heel dissolution on multiple tanks. Using OLI{copyright} and available test results, a dissolution model is constructed and validated. Material and energy balances, coupled with the model, identify potential safety concerns. Overpressurization and overheating are shown to be unlikely. Corrosion induced hydrogen could, however, overwhelm the tank ventilation. While pH adjustment can restore the minimal hydrogen generation, resultant precipitates will notably increase the sludge volume. OLI{copyright} is used to develop a flowsheet such that additional sludge vitrification canisters and other negative system impacts are minimized. Sensitivity analyses are used to assess the processability impacts from variations in the sludge/quantities of acids.

  10. FADO 2.0: A high level tagging language

    Science.gov (United States)

    Werner, C. M. L.; Pimenta, M.; Varela, J.; Souza, J.

    1989-12-01

    FADO 2.0 is a high language, developed in the context of the 4th level trigger of the DELPHI data acquisition project at CERN, that provides a simple and consice way to define physics criteria for event tagging. Its syntax is based on mathematical logic and set theory, as it was found the most appropriate framework to describe the properties of single HEP events. The language is one of the components of the FADO tagging system. The system also implements implicity a mechanism to selectively reconstruct the event data that are needed to fulfil the physics criteria, following the speed requirements of the online data-acquisition system. A complete programming environment is now under development, which will include a syntax directed editor, and incremental compiler, a debugger and a configurer. This last tool can be used to transport the system into the context of other HEP applications, namely offline event selection and filtering.

  11. High-Level Language Production in Parkinson's Disease: A Review

    Directory of Open Access Journals (Sweden)

    Lori J. P. Altmann

    2011-01-01

    Full Text Available This paper discusses impairments of high-level, complex language production in Parkinson's disease (PD, defined as sentence and discourse production, and situates these impairments within the framework of current psycholinguistic theories of language production. The paper comprises three major sections, an overview of the effects of PD on the brain and cognition, a review of the literature on language production in PD, and a discussion of the stages of the language production process that are impaired in PD. Overall, the literature converges on a few common characteristics of language production in PD: reduced information content, impaired grammaticality, disrupted fluency, and reduced syntactic complexity. Many studies also document the strong impact of differences in cognitive ability on language production. Based on the data, PD affects all stages of language production including conceptualization and functional and positional processing. Furthermore, impairments at all stages appear to be exacerbated by impairments in cognitive abilities.

  12. Extending Java for High-Level Web Service Construction

    DEFF Research Database (Denmark)

    Christensen, Aske Simon; Møller, Anders; Schwartzbach, Michael Ignatieff

    2003-01-01

    We incorporate innovations from the project into the Java language to provide high-level features for Web service programming. The resulting language, JWIG, contains an advanced session model and a flexible mechanism for dynamic construction of XML documents, in particular XHTML. To support program...... development we provide a suite of program analyses that at compile time verify for a given program that no runtime errors can occur while building documents or receiving form input, and that all documents being shown are valid according to the document type definition for XHTML 1.0.We compare JWIG...... with Servlets and JSP which are widely used Web service development platforms. Our implementation and evaluation of JWIG indicate that the language extensions can simplify the program structure and that the analyses are sufficiently fast and precise to be practically useful....

  13. High level radioactive waste vitrification process equipment component testing

    Energy Technology Data Exchange (ETDEWEB)

    Siemens, D.H.; Heath, W.O.; Larson, D.E.; Craig, S.N.; Berger, D.N.; Goles, R.W.

    1985-04-01

    Remote operability and maintainability of vitrification equipment were assessed under shielded-cell conditions. The equipment tested will be applied to immobilize high-level and transuranic liquid waste slurries that resulted from plutonium production for defense weapons. Equipment tested included: a turntable for handling waste canisters under the melter; a removable discharge cone in the melter overflow section; a thermocouple jumper that extends into a shielded cell; remote instrument and electrical connectors; remote, mechanical, and heat transfer aspects of the melter glass overflow section; a reamer to clean out plugged nozzles in the melter top; a closed circuit camera to view the melter interior; and a device to retrieve samples of the glass product. A test was also conducted to evaluate liquid metals for use in a liquid metal sealing system.

  14. Sandia National Laboratories' new high level acoustic test facility

    Energy Technology Data Exchange (ETDEWEB)

    Rogers, J. D.; Hendrick, D. M.

    1989-01-01

    A high intensity acoustic test facility has been designed and is under construction at Sandia National Laboratories in Albuquerque, NM. The chamber is designed to provide an acoustic environment of 154dB (re 20 {mu}Pa) overall sound pressure level over the bandwidth of 50 Hz to 10,000 Hz. The chamber has a volume of 16,000 cubic feet with interior dimensions of 21.6 ft {times} 24.6 ft {times} 30 ft. The construction of the chamber should be complete by the summer of 1990. This paper discusses the design goals and constraints of the facility. The construction characteristics are discussed in detail, as are the acoustic performance design characteristics. The authors hope that this work will help others in designing acoustic chambers. 12 refs., 6 figs.

  15. Respiratory physiology: adaptations to high-level exercise.

    Science.gov (United States)

    McKenzie, Donald C

    2012-05-01

    Most exercise scientists would agree that the physiological determinants of peak endurance performance include the capacity to transport oxygen to the working muscle, diffusion from the muscle to the mitochondria, energy production and force generation, all influenced by signals from the central nervous system. In general, the capacity of the pulmonary system far exceeds the demands required for ventilation and gas exchange during exercise. Endurance training induces large and significant adaptations within the cardiovascular, musculoskeletal and haematological systems. However, the structural and functional properties of the lung and airways do not change in response to repetitive physical activity and, in elite athletes, the pulmonary system may become a limiting factor to exercise at sea level and altitude. As a consequence to this respiratory paradox, highly trained athletes may develop intrathoracic and extrathoracic obstruction, expiratory flow limitation, respiratory muscle fatigue and exercise-induced hypoxaemia. All of these maladaptations may influence performance.

  16. Reprogrammable Controller Design From High-Level Specification

    Directory of Open Access Journals (Sweden)

    M. Benmohammed

    2003-10-01

    Full Text Available Existing techniques in high-level synthesis mostly assume a simple controller architecture model in the form of a single FSM. However, in reality more complex controller architectures are often used. On the other hand, in the case of programmable processors, the controller architecture is largely defined by the available control-flow instructions in the instruction set. With the wider acceptance of behavioral synthesis, the application of these methods for the design of programmable controllers is of fundamental importance in embedded system technology. This paper describes an important extension of an existing architectural synthesis system targeting the generation of ASIP reprogrammable architectures. The designer can then generate both style of architecture, hardwired and programmable, using the same synthesis system and can quickly evaluate the trade-offs of hardware decisions.

  17. The ALICE High Level Trigger: status and plans

    CERN Document Server

    Krzewicki, Mikolaj; Gorbunov, Sergey; Breitner, Timo; Lehrbach, Johannes; Lindenstruth, Volker; Berzano, Dario

    2015-01-01

    The ALICE High Level Trigger (HLT) is an online reconstruction, triggering and data compression system used in the ALICE experiment at CERN. Unique among the LHC experiments, it extensively uses modern coprocessor technologies like general purpose graphic processing units (GPGPU) and field programmable gate arrays (FPGA) in the data flow. Realtime data compression is performed using a cluster finder algorithm implemented on FPGA boards. These data, instead of raw clusters, are used in the subsequent processing and storage, resulting in a compression factor of around 4. Track finding is performed using a cellular automaton and a Kalman filter algorithm on GPGPU hardware, where both CUDA and OpenCL technologies can be used interchangeably. The ALICE upgrade requires further development of online concepts to include detector calibration and stronger data compression. The current HLT farm will be used as a test bed for online calibration and both synchronous and asynchronous processing frameworks already before t...

  18. High Level Control Applications for SOLEIL Commissioning and Operation

    CERN Document Server

    Nadolski, Laurent S; Ho, Katy; Leclercq, Nicolas; Ounsy, Majid; Petit, Sylvain

    2005-01-01

    The SOLEIL control system, namely TANGO developed in collaboration with ESRF, is now mature and stable. TANGO has also been chosen now by several other laboratories. High-level control applications implemented in the control room for the storage ring, the two transfer lines, and the booster will be described in this paper. Three kinds of tools for commissioning are used. First the generic TANGO tools (alarms, simple graphical control applications), which allow us to control in a simple way any TANGO Device Server. Secondly a Matlab Middle Layer (adapted from ALS and SPEAR3): Matlab is fully interconnected with TANGO; it is used primarily for writing Physics control applications. Finally Globalscreen, a commercial SCADA software devoted for building operation applications has been selected (panels for controlling or displaying setpoint, readback values, status of equipments). In addition an overview of the historical and short-term databases for the accelerators will be given. They have been developed in house...

  19. High level architecture evolved modular federation object model

    CERN Document Server

    Wang, Wenguang; Chen, Xin; Li, Qun; Wang, Weiping

    2009-01-01

    To improve the agility, dynamics, composability, reusability, and development efficiency restricted by monolithic Federation Object Model (FOM), a modular FOM was proposed by High Level Architecture (HLA) Evolved product development group. This paper reviews the state-of-the-art of HLA Evolved modular FOM. In particular, related concepts, the overall impact on HLA standards, extension principles, and merging processes are discussed. Also permitted and restricted combinations, and merging rules are provided, and the influence on HLA interface specification is given. The comparison between modular FOM and Base Object Model (BOM) is performed to illustrate the importance of their combination. The applications of modular FOM are summarized. Finally, the significance to facilitate composable simulation both in academia and practice is presented and future directions are pointed out.

  20. Simulation Modeling of Space Missions Using the High Level Architecture

    Directory of Open Access Journals (Sweden)

    Luis Rabelo

    2013-01-01

    Full Text Available This paper discusses an environment being developed to model a mission of the Space Launch System (SLS and the Multipurpose Crew Vehicle (MPCV being launched from Kennedy Space Center (KSC to the International Space Station (ISS. Several models representing different phases of the mission such as the ground operations processes, engineered systems, and range components such as failure tree, blast, gas dispersion, and debris modeling are explained. These models are built using different simulation paradigms such as continuous, system dynamics, discrete-event, and agent-based simulation modeling. The High Level Architecture (HLA is the backbone of this distributed simulation. The different design decisions and the information fusion scheme of this unique environment are explained in detail for decision-making. This can also help in the development of exploration missions beyond the International Space Station.

  1. Combined anaerobic ammonium and methane oxidation for nitrogen and methane removal.

    Science.gov (United States)

    Zhu, Baoli; Sánchez, Jaime; van Alen, Theo A; Sanabria, Janeth; Jetten, Mike S M; Ettwig, Katharina F; Kartal, Boran

    2011-12-01

    Anammox (anaerobic ammonium oxidation) is an environment-friendly and cost-efficient nitrogen-removal process currently applied to high-ammonium-loaded wastewaters such as anaerobic digester effluents. In these wastewaters, dissolved methane is also present and should be removed to prevent greenhouse gas emissions into the environment. Potentially, another recently discovered microbial pathway, n-damo (nitrite-dependent anaerobic methane oxidation) could be used for this purpose. In the present paper, we explore the feasibility of simultaneously removing methane and ammonium anaerobically, starting with granules from a full-scale anammox bioreactor. We describe the development of a co-culture of anammox and n-damo bacteria using a medium containing methane, ammonium and nitrite. The results are discussed in the context of other recent studies on the application of anaerobic methane- and ammonia-oxidizing bacteria for wastewater treatment.

  2. Heterotrophic ammonium removal characteristics of an aerobic heterotrophic nitrifying-denitrifying bacterium, Providencia rettgeri YL

    Institute of Scientific and Technical Information of China (English)

    TAYLOR Shauna M; HE Yiliang; ZHAO Bin; HUANG Jue

    2009-01-01

    Bacterium Providencia rettgeri YL was found to exhibit an unusual ability to heterotrophically nitrify and aerobically denitrify various concentrations of ammonium (NH4+-N). In order to further analyze its removal ability, several experiments were conducted to identify the growth and ammonium removal response in different carbon to nitrogen (C/N) mass ratios, shaking speeds, temperatures, ammonium concentrations and to qualitatively verify the production of nitrogen gas using gas chromatography techniques. Results showed that under optimum conditions (C/N 10, 30℃, 120 r/min), YL can significantly remove low and high concentrations of ammonium within 12 to 48 h of growth. The nitrification products hydroxylamine (NH2OH), nitrite (NO2-) and nitrate (NO3-) as well as the denitrification product, nitrogen gas (N2), were detected under completely aerobic conditions.

  3. Nanomodified vermiculite NMV - a new material for recycling ammonium nitrogen

    Science.gov (United States)

    Rama, Miradije; Laiho, Taina; Eklund, Olav; Lehto, Kirsi; Shebanov, Alex; Smått, Jan-Henrik

    2016-04-01

    Vermiculites ((Mg,Fe,Al)3(Al,Si)4O10(OH)24H2O) are naturally occurring minerals from hydromica group with a high cation exchange capacity and large surface area. Since vermiculite is a hydrated mineral, its structure can be changed with heat. In this study vermiculite samples were heated in an oven until the interlayer distance of them diminished from 14 Å to 11.7 Å. This method for improving vermiculites intake of ammonium ions by heating, is an invention made at the University of Turku. Nanomodified vermiculite (NMV) is able to absorb up to 4.7 wt% of ammonium. NMV can be used as an efficient filter and immobilizer of ammonium in different environments. NMV has been efficiently tested on waste water from a biogas plant, human urine, combustion experiments, industrial chimneys, excrements from farms etc. Ammonium doped vermiculite (ADV) is further developed for fertilizer use. Performed experiments have testified the usability of ADV as a fertilizer. At first step the NMV was processed with the reject water from a biogas plant, were it absorbed NH4+ into the lattice. At second, the ADV was used as nutrient source for garden plants. Geraniums and begonias were used as test plants of the work. Plant growth rate was evaluated based on plant weight. Results showed that significant increase of the growth of geraniums and of begonias were observed when comparing to those cultivations where plants have got normal fertilization. Moreover, ADV has been tested as a fertilizer in greenhouse experiments with spruces and pines. After five months, the weight of the plants that had grown in a substrate containing ADV was 10 times the weight of plants growing in the reference substrate.

  4. Ammonium photo-production by heterocytous cyanobacteria: potentials and constraints.

    Science.gov (United States)

    Grizeau, Dominique; Bui, Lan Anh; Dupré, Catherine; Legrand, Jack

    2016-08-01

    Over the last decades, production of microalgae and cyanobacteria has been developed for several applications, including novel foods, cosmetic ingredients and more recently biofuel. The sustainability of these promising developments can be hindered by some constraints, such as water and nutrient footprints. This review surveys data on N2-fixing cyanobacteria for biomass production and ways to induce and improve the excretion of ammonium within cultures under aerobic conditions. The nitrogenase complex is oxygen sensitive. Nevertheless, nitrogen fixation occurs under oxic conditions due to cyanobacteria-specific characteristics. For instance, in some cyanobacteria, the vegetative cell differentiation in heterocyts provides a well-adapted anaerobic microenvironment for nitrogenase protection. Therefore, cell cultures of oxygenic cyanobacteria have been grown in laboratory and pilot photobioreactors (Dasgupta et al., 2010; Fontes et al., 1987; Moreno et al., 2003; Nayak & Das, 2013). Biomass production under diazotrophic conditions has been shown to be controlled by environmental factors such as light intensity, temperature, aeration rate, and inorganic carbon concentration, also, more specifically, by the concentration of dissolved oxygen in the culture medium. Currently, there is little information regarding the production of extracellular ammonium by heterocytous cyanobacteria. This review compares the available data on maximum ammonium concentrations and analyses the specific rate production in cultures grown as free or immobilized filamentous cyanobacteria. Extracellular production of ammonium could be coupled, as suggested by recent research on non-diazotrophic cyanobacteria, to that of other high value metabolites. There is little information available regarding the possibility for using diazotrophic cyanobacteria as cellular factories may be in regard of the constraints due to nitrogen fixation.

  5. High levels of serum hyaluronic acid in adults with dermatomyositis

    Directory of Open Access Journals (Sweden)

    Alana Ausciutti Victorino

    2015-04-01

    Full Text Available Background / objectives. Hyaluronic acid (HA is rarely described in dermatomyositis (DM. Thus, we determined any clinical association of serum levels of hyaluronic acid (HA in patients with dermatomyositis (DM. Materials and Methods. This cross-sectional single-center analysis 75 DM and 75 healthy individuals, during the period from January 2012 to July 2013. An anti-HA antibody assay was performed using specific ELISA/EIA kits, according to the manufacturer’s protocol. Results. The patients with DM and control subjects had comparable demographic distributions (p>0.05. The median time duration between disease diagnosis and initial symptoms was 6.0 [3.0-12.0] months, with a median DM disease duration of 4.0 [1.0-7.0] years. The median level of serum HA was significantly increased in patients with DM compared to the control group [329.0 (80.0-958.0 vs. 133.0 (30.0-262.0 ng/mL, respectively; p0.05. Serum HA also did not correlate with gender, ethnicity, auto-antibodies or drug use (p>0.05, but did correlate with cutaneous features, such as photosensitivity (p=0.001, “shawl” sign (p=0.018, “V-neck” sign (p=0.005 and cuticular hypertrophy (p=0.014. Conclusions. A high level of serum AH was observed in DM compared to healthy individuals. In DM, HA did not correlate to demographic, auto-antibodies and therapy parameters. However, HA correlated specifically with some cutaneous features, suggesting that this glycosaminoglycan could be involved in modulating cutaneous inflammation in this population. More studies are necessary to understand the correlation between AH and patients with DM.

  6. Automatic run-configuration of the ALICE High Level Trigger

    Energy Technology Data Exchange (ETDEWEB)

    Steinbeck, Timm [Frankfurt Institute for Advanced Studies, University Frankfurt (Germany)

    2010-07-01

    The ALICE High Level Trigger (HLT) uses a pipelined and component based approach for data reconstruction and analysis. Processing components push data to the next step in the processing chain via a common interface. Data flow components transport data between nodes and merge different parts of data belonging to the same event. In order for this to work, a configuration for a processing chain has to be created before the start of a run. A repository of XML files is used to automate this, with each file holding the necessary configuration for one component, including its parents components that provide its input data. The ALICE Experiment Control System (ECS) provides a number of configuration parameters to the HLT, including an identifier for the trigger menu with the algorithms to run, a list of participating detectors, and a list of active input DDLs providing data from the detectors to DAQ and HLT. From these parameters an HLT configuration is determined fully automatically including determination of the full parent hierarchy from the top-level trigger and output components to the components receiving the data from the detector, without any manual intervention or configuration.

  7. Hemipelvectomy: high-level amputation surgery and prosthetic rehabilitation.

    Science.gov (United States)

    Houdek, Matthew T; Kralovec, Michael E; Andrews, Karen L

    2014-07-01

    The hemipelvectomy, most commonly performed for pelvic tumor resection, is one of the most technically demanding and invasive surgical procedures performed today. Adequate soft tissue coverage and wound complications after hemipelvectomy are important considerations. Rehabilitation after hemipelvectomy is optimally managed by a multidisciplinary integrated team. Understanding the functional outcomes for this population assists the rehabilitation team to counsel patients, plan goals, and determine discharge needs. The most important rehabilitation goal is the optimal restoration of the patient's functional independence. Factors such as age, sex, etiology, level of amputation, and general health play important roles in determining prosthetic use. The three main criteria for successful prosthetic rehabilitation of patients with high-level amputation are comfort, function, and cosmesis. Recent advances in hip and knee joints have contributed to increased function. Prosthetic use after hemipelvectomy improves balance and decreases the need for a gait aid. Using a prosthesis helps maintain muscle strength and tone, cardiovascular health, and functional mobility. With new advances in prosthetic components, patients are choosing to use their prostheses for primary mobility.

  8. The LHCb Data Acquisition and High Level Trigger Processing Architecture

    Science.gov (United States)

    Frank, M.; Gaspar, C.; Jost, B.; Neufeld, N.

    2015-12-01

    The LHCb experiment at the LHC accelerator at CERN collects collisions of particle bunches at 40 MHz. After a first level of hardware trigger with an output rate of 1 MHz, the physically interesting collisions are selected by running dedicated trigger algorithms in the High Level Trigger (HLT) computing farm. This farm consists of up to roughly 25000 CPU cores in roughly 1750 physical nodes each equipped with up to 4 TB local storage space. This work describes the LHCb online system with an emphasis on the developments implemented during the current long shutdown (LS1). We will elaborate the architecture to treble the available CPU power of the HLT farm and the technicalities to determine and verify precise calibration and alignment constants which are fed to the HLT event selection procedure. We will describe how the constants are fed into a two stage HLT event selection facility using extensively the local disk buffering capabilities on the worker nodes. With the installed disk buffers, the CPU resources can be used during periods of up to ten days without beams. These periods in the past accounted to more than 70% of the total time.

  9. Pupil dilation dynamics track attention to high-level information.

    Directory of Open Access Journals (Sweden)

    Olivia E Kang

    Full Text Available It has long been thought that the eyes index the inner workings of the mind. Consistent with this intuition, empirical research has demonstrated that pupils dilate as a consequence of attentional effort. Recently, Smallwood et al. (2011 demonstrated that pupil dilations not only provide an index of overall attentional effort, but are time-locked to stimulus changes during attention (but not during mind-wandering. This finding suggests that pupil dilations afford a dynamic readout of conscious information processing. However, because stimulus onsets in their study involved shifts in luminance as well as information, they could not determine whether this coupling of stimulus and pupillary dynamics reflected attention to low-level (luminance or high-level (information changes. Here, we replicated the methodology and findings of Smallwood et al. (2011 while controlling for luminance changes. When presented with isoluminant digit sequences, participants' pupillary dilations were synchronized with stimulus onsets when attending, but not when mind-wandering. This replicates Smallwood et al. (2011 and clarifies their finding by demonstrating that stimulus-pupil coupling reflects online cognitive processing beyond sensory gain.

  10. Deep level defects in high temperature annealed InP

    Institute of Scientific and Technical Information of China (English)

    DONG Zhiyuan; ZHAO Youwen; ZENG Yiping; DUAN Manlong; LIN Lanying

    2004-01-01

    Deep level defects in high temperature annealed semi-conducting InP have been studied by deep level transient spectroscopy (DLTS). There is obvious difference in the deep defects between as-grown InP, InP annealed in phosphorus ambient and iron phosphide ambient, as far as their quantity and concentration are concerned. Only two defects at 0.24 and 0.64 eV can be detected in InP annealed iniron phosphide ambient,while defects at 0.24, 0.42, 0.54 and 0.64 eV have been detected in InP annealed in phosphorus ambient, in contrast to two defects at 0.49 and 0.64 eV or one defect at 0.13eV in as-grown InP. A defect suppression phenomenon related to iron diffusion process has been observed. The formation mechanism and the nature of the defects have been discussed.

  11. Reassimilation of Photorespiratory Ammonium in Lotus japonicus Plants Deficient in Plastidic Glutamine Synthetase.

    Science.gov (United States)

    Pérez-Delgado, Carmen M; García-Calderón, Margarita; Márquez, Antonio J; Betti, Marco

    2015-01-01

    It is well established that the plastidic isoform of glutamine synthetase (GS2) is the enzyme in charge of photorespiratory ammonium reassimilation in plants. The metabolic events associated to photorespiratory NH4(+) accumulation were analyzed in a Lotus japonicus photorespiratory mutant lacking GS2. The mutant plants accumulated high levels of NH4(+) when photorespiration was active, followed by a sudden drop in the levels of this compound. In this paper it was examined the possible existence of enzymatic pathways alternative to GS2 that could account for this decline in the photorespiratory ammonium. Induction of genes encoding for cytosolic glutamine synthetase (GS1), glutamate dehydrogenase (GDH) and asparagine synthetase (ASN) was observed in the mutant in correspondence with the diminishment of NH4(+). Measurements of gene expression, polypeptide levels, enzyme activity and metabolite levels were carried out in leaf samples from WT and mutant plants after different periods of time under active photorespiratory conditions. In the case of asparagine synthetase it was not possible to determine enzyme activity and polypeptide content; however, an increased asparagine content in parallel with the induction of ASN gene expression was detected in the mutant plants. This increase in asparagine levels took place concomitantly with an increase in glutamine due to the induction of cytosolic GS1 in the mutant, thus revealing a major role of cytosolic GS1 in the reassimilation and detoxification of photorespiratory NH4(+) when the plastidic GS2 isoform is lacking. Moreover, a diminishment in glutamate levels was observed, that may be explained by the induction of NAD(H)-dependent GDH activity.

  12. Reassimilation of Photorespiratory Ammonium in Lotus japonicus Plants Deficient in Plastidic Glutamine Synthetase.

    Directory of Open Access Journals (Sweden)

    Carmen M Pérez-Delgado

    Full Text Available It is well established that the plastidic isoform of glutamine synthetase (GS2 is the enzyme in charge of photorespiratory ammonium reassimilation in plants. The metabolic events associated to photorespiratory NH4(+ accumulation were analyzed in a Lotus japonicus photorespiratory mutant lacking GS2. The mutant plants accumulated high levels of NH4(+ when photorespiration was active, followed by a sudden drop in the levels of this compound. In this paper it was examined the possible existence of enzymatic pathways alternative to GS2 that could account for this decline in the photorespiratory ammonium. Induction of genes encoding for cytosolic glutamine synthetase (GS1, glutamate dehydrogenase (GDH and asparagine synthetase (ASN was observed in the mutant in correspondence with the diminishment of NH4(+. Measurements of gene expression, polypeptide levels, enzyme activity and metabolite levels were carried out in leaf samples from WT and mutant plants after different periods of time under active photorespiratory conditions. In the case of asparagine synthetase it was not possible to determine enzyme activity and polypeptide content; however, an increased asparagine content in parallel with the induction of ASN gene expression was detected in the mutant plants. This increase in asparagine levels took place concomitantly with an increase in glutamine due to the induction of cytosolic GS1 in the mutant, thus revealing a major role of cytosolic GS1 in the reassimilation and detoxification of photorespiratory NH4(+ when the plastidic GS2 isoform is lacking. Moreover, a diminishment in glutamate levels was observed, that may be explained by the induction of NAD(H-dependent GDH activity.

  13. Ammonium accumulation and cell death in a rat 3D brain cell model of glutaric aciduria type I.

    Directory of Open Access Journals (Sweden)

    Paris Jafari

    Full Text Available Glutaric aciduria type I (glutaryl-CoA dehydrogenase deficiency is an inborn error of metabolism that usually manifests in infancy by an acute encephalopathic crisis and often results in permanent motor handicap. Biochemical hallmarks of this disease are elevated levels of glutarate and 3-hydroxyglutarate in blood and urine. The neuropathology of this disease is still poorly understood, as low lysine diet and carnitine supplementation do not always prevent brain damage, even in early-treated patients. We used a 3D in vitro model of rat organotypic brain cell cultures in aggregates to mimic glutaric aciduria type I by repeated administration of 1 mM glutarate or 3-hydroxyglutarate at two time points representing different developmental stages. Both metabolites were deleterious for the developing brain cells, with 3-hydroxyglutarate being the most toxic metabolite in our model. Astrocytes were the cells most strongly affected by metabolite exposure. In culture medium, we observed an up to 11-fold increase of ammonium in the culture medium with a concomitant decrease of glutamine. We further observed an increase in lactate and a concomitant decrease in glucose. Exposure to 3-hydroxyglutarate led to a significantly increased cell death rate. Thus, we propose a three step model for brain damage in glutaric aciduria type I: (i 3-OHGA causes the death of astrocytes, (ii deficiency of the astrocytic enzyme glutamine synthetase leads to intracerebral ammonium accumulation, and (iii high ammonium triggers secondary death of other brain cells. These unexpected findings need to be further investigated and verified in vivo. They suggest that intracerebral ammonium accumulation might be an important target for the development of more effective treatment strategies to prevent brain damage in patients with glutaric aciduria type I.

  14. On the evaporation of ammonium sulfate solution

    Energy Technology Data Exchange (ETDEWEB)

    Drisdell, Walter S.; Saykally, Richard J.; Cohen, Ronald C.

    2009-07-16

    Aqueous evaporation and condensation kinetics are poorly understood, and uncertainties in their rates affect predictions of cloud behavior and therefore climate. We measured the cooling rate of 3 M ammonium sulfate droplets undergoing free evaporation via Raman thermometry. Analysis of the measurements yields a value of 0.58 {+-} 0.05 for the evaporation coefficient, identical to that previously determined for pure water. These results imply that subsaturated aqueous ammonium sulfate, which is the most abundant inorganic component of atmospheric aerosol, does not affect the vapor-liquid exchange mechanism for cloud droplets, despite reducing the saturation vapor pressure of water significantly.

  15. High estradiol levels improve false memory rates and meta-memory in highly schizotypal women.

    Science.gov (United States)

    Hodgetts, Sophie; Hausmann, Markus; Weis, Susanne

    2015-10-30

    Overconfidence in false memories is often found in patients with schizophrenia and healthy participants with high levels of schizotypy, indicating an impairment of meta-cognition within the memory domain. In general, cognitive control is suggested to be modulated by natural fluctuations in oestrogen. However, whether oestrogen exerts beneficial effects on meta-memory has not yet been investigated. The present study sought to provide evidence that high levels of schizotypy are associated with increased false memory rates and overconfidence in false memories, and that these processes may be modulated by natural differences in estradiol levels. Using the Deese-Roediger-McDermott paradigm, it was found that highly schizotypal participants with high estradiol produced significantly fewer false memories than those with low estradiol. No such difference was found within the low schizotypy participants. Highly schizotypal participants with high estradiol were also less confident in their false memories than those with low estradiol; low schizotypy participants with high estradiol were more confident. However, these differences only approached significance. These findings suggest that the beneficial effect of estradiol on memory and meta-memory observed in healthy participants is specific to highly schizotypal individuals and might be related to individual differences in baseline dopaminergic activity.

  16. Fluorescência e teores de clorofilas em abacaxizeiro cv. pérola submetido a diferentes concentrações de sulfato de amônio Fluorescence and levels of chlorophyll in pineapple plants cv. perola submitted to different concentration of ammonium sulphate

    Directory of Open Access Journals (Sweden)

    Darlene Ana de Paula Vieira

    2010-06-01

    Full Text Available O presente trabalho teve como objetivo a análise da emissão da fluorescência da clorofila a e dos teores de clorofilas em plantas de Ananas comosus (L. Merril cv pérola, cultivadas em casa de vegetação, submetidas a quatro concentrações de nitrogênio por adição ou não de sulfato de amônio, de acordo com os seguintes tratamentos: Tº= 0 T1/2 = 15; T1 = 30; e T2 = 60 mg/kg solo. As determinações de fluorescência mínima (F0, máxima (Fm, variável (Fv, terminal (Ft e da eficiência fotoquímica máxima (Fv/Fm de folhas adaptadas ao escuro foram realizadas ao longo do dia, aos cinco dias após a segunda aplicação de sulfato de amônio, efetuada 120 dias após o transplantio. A adição de sulfato de amônio afetou a fluorescência variável e a máxima, mas não afetou a fluorescência mínima, a terminal nem a eficiência fotoquímica. Houve diferenças significativas entre os valores das variáveis da fluorescência ao longo do dia em que foram feitas as leituras. Houve diferenças nos teores de clorofilas foliares, em função das concentrações de sulfato de amônio aplicadas, com aumento para clorofila a e para a relação clorofila a/b, mas não para clorofila b.The present research aimed to analyze chlorophyll a fluorescence emission as well as chlorophyll levels in Ananas comosus (L. Merril cv Pérola grown under greenhouse conditions and submitted to four concentration of nitrogen, through addition or not of ammonium sulphate according to the following treatments: Tº= 0.000; T1/2 = 0.015; T1 =0.030; and T2 = 0.060 g/kg soil. Determinations of minimum (F0, maximum (Fm, variable (Fv, and terminal (Ft fluorescence and maximum photochemical efficiency (Fv/Fm of dark-adapted leaves were carried out during the day, five days after the second application of ammonium sulphate, carried out 120 days after the transplant. The results showed that the addition of ammonium sulphate affected variable and maximum fluorescence, but not

  17. Removal of ammonium from aqueous solutions using alkali-modified biochars

    Directory of Open Access Journals (Sweden)

    Zhigang Liu

    2016-10-01

    Full Text Available Biochars converted from agricultural residuals can effectively remove ammonium from water. This work further improved the sorption ability of biochars to aqueous ammonium through alkali modification. Three modified biochars were prepared from agricultural residuals pre-treated with NaOH solution through low-temperature (300 °C slow pyrolysis. The modified biochars effectively removed ammonium ions from water under various conditions with relatively fast adsorption kinetics (reached equilibrium within 10 h and extremely high adsorption capacity (>200 mg/g. The Langmuir maximum capacity of the three modified biochars were between 313.9 and 518.9 mg/g, higher than many other ammonium adsorbents. Although the sorption of ammonium onto the modified biochar was affected by pH and temperature, it was high under all of the tested conditions. Findings from this work indicated that alkali-modified biochars can be used as an alternative adsorbent for the removal of ammonium from wastewater.

  18. Review of high-level waste form properties. [146 bibliographies

    Energy Technology Data Exchange (ETDEWEB)

    Rusin, J.M.

    1980-12-01

    This report is a review of waste form options for the immobilization of high-level-liquid wastes from the nuclear fuel cycle. This review covers the status of international research and development on waste forms as of May 1979. Although the emphasis in this report is on waste form properties, process parameters are discussed where they may affect final waste form properties. A summary table is provided listing properties of various nuclear waste form options. It is concluded that proposed waste forms have properties falling within a relatively narrow range. In regard to crystalline versus glass waste forms, the conclusion is that either glass of crystalline materials can be shown to have some advantage when a single property is considered; however, at this date no single waste form offers optimum properties over the entire range of characteristics investigated. A long-term effort has been applied to the development of glass and calcine waste forms. Several additional waste forms have enough promise to warrant continued research and development to bring their state of development up to that of glass and calcine. Synthetic minerals, the multibarrier approach with coated particles in a metal matrix, and high pressure-high temperature ceramics offer potential advantages and need further study. Although this report discusses waste form properties, the total waste management system should be considered in the final selection of a waste form option. Canister design, canister materials, overpacks, engineered barriers, and repository characteristics, as well as the waste form, affect the overall performance of a waste management system. These parameters were not considered in this comparison.

  19. Some effects of ammonium salts on renal histology and function in the dog.

    Science.gov (United States)

    Orvell, B D; Wesson, L G

    1976-01-01

    NH4Cl was infused into the left renal artery of anesthetized dogs at 50-125 mum/kg/min for up to 110 min. Renal blood flow declined early then increased to supra-control levels during infusion. Kidneys perfused at 125 mum/kg/min for 90 min showed patchy to confluent mixtures of cortical necrosis and tubular necrosis. Experimental kidneys invariably showed lower urine osmolality than contralateral controls 48 h after perfusion. Kidneys with necrosis showed depressed creatinine clearance as well. Renal artery infusion of NH4 acetate or intravenous infusion of NaHCO3 during arterial infusion of NH4Cl prevented significant acidosis and caused minimal histological changes, but depression of urine osmolality was not prevented. It is concluded that renal ammonium concentrations up to 40 mum/liter for 90 min does not cause tubular necrosis but does impair urine concentration. Severe tissue damage followed renal exposure to high ammonium concentrations in the presence of metabolic or renal acidosis.

  20. Evidence of ammonium ion-exchange properties of natural bentonite and application to ammonium detection.

    Science.gov (United States)

    Zazoua, A; Kazane, I; Khedimallah, N; Dernane, C; Errachid, A; Jaffrezic-Renault, N

    2013-12-01

    Ammonium exchange with hybrid PVC-bentonite (mineral montmorillonite clay) thin film was revealed using FTIR spectroscopy, EDX, cyclic voltammetry and electrochemical impedance spectroscopy. The effect of ammonium exchange on the charge transfer resistance of PVC-bentonite hybrid thin film was attributed to a modification of the intersheet distance and hydration of bentonite crystals. The obtained impedimetric ammonium sensor shows a linear range of detection from 10(-4)M to 1M and a detection limit around 10(-6)M. © 2013.

  1. Effects of Aromatic Ammoniums on Methyl Ammonium Lead Iodide Hybrid Perovskite Materials

    Directory of Open Access Journals (Sweden)

    Jianli Yang

    2017-01-01

    Full Text Available The introduction of bulky ammoniums into methyl ammonium lead iodide hybrid perovskites (MAPbI3 has emerged as a promising strategy to improve the properties of these materials. In the present work, we studied the effects of several aromatic ammoniums onto the structural, electronic, and optical properties of MAPbI3. Although powder XRD data suggest that the bulky cations are not involved in the bulk phase of the MAPbI3, a surprisingly large effect of the bulky cations onto the photoluminescence properties was observed.

  2. Interventions for Individuals With High Levels of Needle Fear

    Science.gov (United States)

    Noel, Melanie; Taddio, Anna; Antony, Martin M.; Asmundson, Gordon J.G.; Riddell, Rebecca Pillai; Chambers, Christine T.; Shah, Vibhuti

    2015-01-01

    Background: This systematic review evaluated the effectiveness of exposure-based psychological and physical interventions for the management of high levels of needle fear and/or phobia and fainting in children and adults. Design/Methods: A systematic review identified relevant randomized and quasi-randomized controlled trials of children, adults, or both with high levels of needle fear, including phobia (if not available, then populations with other specific phobias were included). Critically important outcomes were self-reported fear specific to the feared situation and stimulus (psychological interventions) or fainting (applied muscle tension). Data were pooled using standardized mean difference (SMD) or relative risk with 95% confidence intervals. Results: The systematic review included 11 trials. In vivo exposure-based therapy for children 7 years and above showed benefit on specific fear (n=234; SMD: −1.71 [95% CI: −2.72, −0.7]). In vivo exposure-based therapy with adults reduced fear of needles posttreatment (n=20; SMD: −1.09 [−2.04, −0.14]) but not at 1-year follow-up (n=20; SMD: −0.28 [−1.16, 0.6]). Compared with single session, a benefit was observed for multiple sessions of exposure-based therapy posttreatment (n=93; SMD: −0.66 [−1.08, −0.24]) but not after 1 year (n=83; SMD: −0.37 [−0.87, 0.13]). Non in vivo e.g., imaginal exposure-based therapy in children reduced specific fear posttreatment (n=41; SMD: −0.88 [−1.7, −0.05]) and at 3 months (n=24; SMD: −0.89 [−1.73, −0.04]). Non in vivo exposure-based therapy for adults showed benefit on specific fear (n=68; SMD: −0.62 [−1.11, −0.14]) but not procedural fear (n=17; SMD: 0.18 [−0.87, 1.23]). Applied tension showed benefit on fainting posttreatment (n=20; SMD: −1.16 [−2.12, −0.19]) and after 1 year (n=20; SMD: −0.97 [−1.91, −0.03]) compared with exposure alone. Conclusions: Exposure-based psychological interventions and applied muscle tension show

  3. Spent nuclear fuel project high-level information management plan

    Energy Technology Data Exchange (ETDEWEB)

    Main, G.C.

    1996-09-13

    This document presents the results of the Spent Nuclear Fuel Project (SNFP) Information Management Planning Project (IMPP), a short-term project that identified information management (IM) issues and opportunities within the SNFP and outlined a high-level plan to address them. This high-level plan for the SNMFP IM focuses on specific examples from within the SNFP. The plan`s recommendations can be characterized in several ways. Some recommendations address specific challenges that the SNFP faces. Others form the basis for making smooth transitions in several important IM areas. Still others identify areas where further study and planning are indicated. The team`s knowledge of developments in the IM industry and at the Hanford Site were crucial in deciding where to recommend that the SNFP act and where they should wait for Site plans to be made. Because of the fast pace of the SNFP and demands on SNFP staff, input and interaction were primarily between the IMPP team and members of the SNFP Information Management Steering Committee (IMSC). Key input to the IMPP came from a workshop where IMSC members and their delegates developed a set of draft IM principles. These principles, described in Section 2, became the foundation for the recommendations found in the transition plan outlined in Section 5. Availability of SNFP staff was limited, so project documents were used as a basis for much of the work. The team, realizing that the status of the project and the environment are continually changing, tried to keep abreast of major developments since those documents were generated. To the extent possible, the information contained in this document is current as of the end of fiscal year (FY) 1995. Programs and organizations on the Hanford Site as a whole are trying to maximize their return on IM investments. They are coordinating IM activities and trying to leverage existing capabilities. However, the SNFP cannot just rely on Sitewide activities to meet its IM requirements

  4. Energy Levels of Highly Ionized Ar ⅩⅣ

    Institute of Scientific and Technical Information of China (English)

    CHENG Zhang; LI Ping; DENG Xiao-Hui

    2006-01-01

    With the Breit interaction and quantum electrodynamics corrections considered, relativistic configuration interaction calculations have been carried out in the extended optimal level scheme using multi-configuration Dirac-Fock wave functions on the 204 energy levels and electric dipole transitions of Ar ⅩⅣ. The results of electric dipole transitions are in good agreement with experiments. Among the energy levels calculated, the lowest 125 levels are in good agreement with available experimental and other theoretical ones, and the other 79 levels are new ones obtained by the present work. This wide range of atomic energy levels is useful in astrophysics and plasma physics.

  5. Deep borehole disposal of high-level radioactive waste.

    Energy Technology Data Exchange (ETDEWEB)

    Stein, Joshua S.; Freeze, Geoffrey A.; Brady, Patrick Vane; Swift, Peter N.; Rechard, Robert Paul; Arnold, Bill Walter; Kanney, Joseph F.; Bauer, Stephen J.

    2009-07-01

    Preliminary evaluation of deep borehole disposal of high-level radioactive waste and spent nuclear fuel indicates the potential for excellent long-term safety performance at costs competitive with mined repositories. Significant fluid flow through basement rock is prevented, in part, by low permeabilities, poorly connected transport pathways, and overburden self-sealing. Deep fluids also resist vertical movement because they are density stratified. Thermal hydrologic calculations estimate the thermal pulse from emplaced waste to be small (less than 20 C at 10 meters from the borehole, for less than a few hundred years), and to result in maximum total vertical fluid movement of {approx}100 m. Reducing conditions will sharply limit solubilities of most dose-critical radionuclides at depth, and high ionic strengths of deep fluids will prevent colloidal transport. For the bounding analysis of this report, waste is envisioned to be emplaced as fuel assemblies stacked inside drill casing that are lowered, and emplaced using off-the-shelf oilfield and geothermal drilling techniques, into the lower 1-2 km portion of a vertical borehole {approx}45 cm in diameter and 3-5 km deep, followed by borehole sealing. Deep borehole disposal of radioactive waste in the United States would require modifications to the Nuclear Waste Policy Act and to applicable regulatory standards for long-term performance set by the US Environmental Protection Agency (40 CFR part 191) and US Nuclear Regulatory Commission (10 CFR part 60). The performance analysis described here is based on the assumption that long-term standards for deep borehole disposal would be identical in the key regards to those prescribed for existing repositories (40 CFR part 197 and 10 CFR part 63).

  6. High-level disinfection of gastrointestinal endoscope reprocessing.

    Science.gov (United States)

    Chiu, King-Wah; Lu, Lung-Sheng; Chiou, Shue-Shian

    2015-02-20

    High level disinfection (HLD) of the gastrointestinal (GI) endoscope is not simply a slogan, but rather is a form of experimental monitoring-based medicine. By definition, GI endoscopy is a semicritical medical device. Hence, such medical devices require major quality assurance for disinfection. And because many of these items are temperature sensitive, low-temperature chemical methods, such as liquid chemical germicide, must be used rather than steam sterilization. In summarizing guidelines for infection prevention and control for GI endoscopy, there are three important steps that must be highlighted: manual washing, HLD with automated endoscope reprocessor, and drying. Strict adherence to current guidelines is required because compared to any other medical device, the GI endoscope is associated with more outbreaks linked to inadequate cleaning or disinfecting during HLD. Both experimental evaluation on the surveillance bacterial cultures and in-use clinical results have shown that, the monitoring of the stringent processes to prevent and control infection is an essential component of the broader strategy to ensure the delivery of safe endoscopy services, because endoscope reprocessing is a multistep procedure involving numerous factors that can interfere with its efficacy. Based on our years of experience in the surveillance of culture monitoring of endoscopic reprocessing, we aim in this study to carefully describe what details require attention in the GI endoscopy disinfection and to share our experience so that patients can be provided with high quality and safe medical practices. Quality management encompasses all aspects of pre- and post-procedural care including the efficiency of the endoscopy unit and reprocessing area, as well as the endoscopic procedure itself.

  7. 77 FR 59106 - Glufosinate Ammonium; Pesticide Tolerances

    Science.gov (United States)

    2012-09-26

    ... identified. Cancer (Oral, dermal, inhalation) Classification: ``Not likely to be Carcinogenic to Humans... apple juice, pear juice, grape juice, and raisins, for which factors derived from the processing studies... crops that are currently registered for glufosinate ammonium if available. iii. Cancer. Based on the...

  8. Topaz concentrate desiliconization with ammonium bifluoride

    OpenAIRE

    Andreev, V. A.; Buynovskiy, A. S.; Andreev, Artyom Andreevich; Dyachenko, Alexander Nikolaevich

    2007-01-01

    Fluoridizing agent for the process of topaz concentrate desiliconization has been selected, topaz thermodynamic potentials have been appraised, thermodynamic probabilities of fluorination reaction of topaz concentrate main constituents have been calculated. The results of studying the concentrate desiliconization process with ammonium bifluoride by the methods of thermogravimetry, RFA, microphotography are presented

  9. Detonation characteristics of ammonium nitrate products

    NARCIS (Netherlands)

    Kersten, R.J.A.; Hengel, E.I.V. van den; Steen, A.C. van der

    2006-01-01

    The detonation properties of ammonium nitrate (AN) products depend on many factors and are therefore, despite the large amount of information on this topic, difficult to assess. In order to further improve the understanding of the safety properties of AN, the European Fertilizer Manufacturers Associ

  10. Review of Ammonium Dinitramide Toxicity Studies

    Science.gov (United States)

    2011-01-01

    reproductive toxicant in rats, causing implantation failure in early gestation; follow-on studies implied that ADN is embryotoxic . EPR studies indicated that...mutagenic. 15. SUBJECT TERMS Ammonium dinitramide, ADN, toxicity, reproductive, embryotoxic , genotoxicity 16. SECURITY CLASSIFICATION OF: U 17...reproductive studies, reproduction and fertility, pre-implantation and post-implantation studies, implied that ADN is embryotoxic . A mouse embryo

  11. EFFECT OF AMMONIUM NITRATE SOLUTIONS ON ...

    African Journals Online (AJOL)

    1957; Ball 1967) but the effects of these salts on marine animals is less well known. .... The first clear result of the experiments is that concentrations of ammonium ... study it is useful to know the tolerance of different stages in the life history.

  12. Effect of free ammonium and free nitrous acid on the activity, aggregate morphology and extracellular polymeric substance distribution of ammonium oxidizing bacteria in partial nitrification.

    Science.gov (United States)

    Yao, Qian; Peng, Dangcong; Wang, Bo; Chen, Yuanyuan; Li, Jiaqi; Zhao, Qiaodi; Wang, Binbin

    2017-09-01

    Successful partial nitrification not only guarantees the inhibition of nitrite oxidation, but also does not excessively retard the ammonia oxidation rate. Therefore, the performance of ammonium oxidizing bacteria (AOB) during partial nitrification is fundamental to this process. In this study, two lab-scale partial nitrification bioreactors containing different inhibition conditions-one with free ammonium (FA) inhibition, the other with free nitrous acid (FNA) inhibition-were used to compare the differences between activity, quantity, aggregation morphology and extracellular polymeric substance (EPS) distribution of AOB. The results showed that although stable, long-term, partial nitrification was achieved in both reactors, there were differences in AOB activity, microbial spatial distribution and EPS characteristic. In the FA bioreactor, FA concentration was conducted at more than 40 mg/L, which had a strong impact on the metabolism of AOB. The activity and quantity decreased by 50%. Higher EPS (42.44 ± 2.31 mg g(-1) mixed liquor volatile suspended solids [MLVSS]) and protein were introduced into the EPS matrix. However, in the FNA bioreactor, the FNA concentration was about 0.23 mg/L. It did not reach a level to affect AOB metabolism. The AOB activity and quantity were maintained at high levels and the total EPS content was 28.29 ± 2.04 mg g(-1) MLVSS. Additionally, the microscopic results showed that in the FA bioreactor, AOB cells aggregated in microcolonies, while they appeared to be self-flocculating with no specific conformation in the other reactor. β-polysaccharides located inside sludge flocs in the FA bioreactor but only accumulated around the outer layer of activated sludge flocs in the FNA condition. Copyright © 2017 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

  13. The ATLAS High Level Trigger Infrastructure, Performance and Future Developments

    CERN Document Server

    Winklmeier, F; The ATLAS collaboration

    2009-01-01

    The ATLAS High Level Trigger (HLT) is a distributed real-time software system that performs the final online selection of events produced during proton-proton collisions at the Large Hadron Collider (LHC). It is designed as a two-stage event filter running on a farm of commodity PC hardware. Currently the system consists of about 850 multi-core processing nodes that will be extended incrementally following the increasing luminosity of the LHC to about 2000 nodes depending on the evolution of the processor technology. Due to the complexity and similarity of the algorithms a large fraction of the software is shared between the online and offline event reconstruction. The HLT Infrastructure serves as the interface between the two domains and provides common services for the trigger algorithms. The consequences of this design choice will be discussed and experiences from the operation of the ATLAS HLT during cosmic ray data taking and first beam in 2008 will be presented. Since the event processing time at the HL...

  14. The GRAVITY instrument software/high-level software

    Science.gov (United States)

    Burtscher, Leonard; Wieprecht, Ekkehard; Ott, Thomas; Kok, Yitping; Yazici, Senol; Anugu, Narsireddy; Dembet, Roderick; Fedou, Pierre; Lacour, Sylvestre; Ott, Jürgen; Paumard, Thibaut; Lapeyrere, Vincent; Kervella, Pierre; Abuter, Roberto; Pozna, Eszter; Eisenhauer, Frank; Blind, Nicolas; Genzel, Reinhard; Gillessen, Stefan; Hans, Oliver; Haug, Marcus; Haussmann, Frank; Kellner, Stefan; Lippa, Magdalena; Pfuhl, Oliver; Sturm, Eckhard; Weber, Johannes; Amorim, Antonio; Brandner, Wolfgang; Rousselet-Perraut, Karine; Perrin, Guy S.; Straubmeier, Christian; Schöller, Markus

    2014-07-01

    GRAVITY is the four-beam, near-infrared, AO-assisted, fringe tracking, astrometric and imaging instrument for the Very Large Telescope Interferometer (VLTI). It is requiring the development of one of the most complex instrument software systems ever built for an ESO instrument. Apart from its many interfaces and interdependencies, one of the most challenging aspects is the overall performance and stability of this complex system. The three infrared detectors and the fast reflective memory network (RMN) recorder contribute a total data rate of up to 20 MiB/s accumulating to a maximum of 250 GiB of data per night. The detectors, the two instrument Local Control Units (LCUs) as well as the five LCUs running applications under TAC (Tools for Advanced Control) architecture, are interconnected with fast Ethernet, RMN fibers and dedicated fiber connections as well as signals for the time synchronization. Here we give a simplified overview of all subsystems of GRAVITY and their interfaces and discuss two examples of high-level applications during observations: the acquisition procedure and the gathering and merging of data to the final FITS file.

  15. The ALICE High Level Trigger: status and plans

    Science.gov (United States)

    Krzewicki, Mikolaj; Rohr, David; Gorbunov, Sergey; Breitner, Timo; Lehrbach, Johannes; Lindenstruth, Volker; Berzano, Dario

    2015-12-01

    The ALICE High Level Trigger (HLT) is an online reconstruction, triggering and data compression system used in the ALICE experiment at CERN. Unique among the LHC experiments, it extensively uses modern coprocessor technologies like general purpose graphic processing units (GPGPU) and field programmable gate arrays (FPGA) in the data flow. Realtime data compression is performed using a cluster finder algorithm implemented on FPGA boards. These data, instead of raw clusters, are used in the subsequent processing and storage, resulting in a compression factor of around 4. Track finding is performed using a cellular automaton and a Kalman filter algorithm on GPGPU hardware, where both CUDA and OpenCL technologies can be used interchangeably. The ALICE upgrade requires further development of online concepts to include detector calibration and stronger data compression. The current HLT farm will be used as a test bed for online calibration and both synchronous and asynchronous processing frameworks already before the upgrade, during Run 2. For opportunistic use as a Grid computing site during periods of inactivity of the experiment a virtualisation based setup is deployed.

  16. Psychological stress in high level sailors during competition

    Directory of Open Access Journals (Sweden)

    Luciana Segato

    2010-09-01

    Full Text Available The purpose of this work was to investigate the psychological stress present in elite sailors in a competition. Based on a descriptive field research, 31 elite sailors volunteered to participate. They answered the Perceived Stress Scale (Cohen & Williamson, 1988 and also specific questions on self-control, sources and strategies of coping. Data were analyzed by using descriptive and inferential (Student t test and Pearson's correlation statistics. These athletes revealed low and moderate scores (M = 20.00, DP = 6.83 of stress originated from both intrinsic (ship troubles, team disorders and extrinsic (study, working and training, family and financial problems sources. The group reported good stress control during competition through the use of cognitive (avoidance and somatic (listening music, resting/sleeping, talk to friends strategies. It is important that sailors are able to control and cope with high levels of psychological stress and to understand how to proceed when under unstable and unexpected situations that arise during competition.

  17. Psychological stress in high level sailors during competition

    Directory of Open Access Journals (Sweden)

    L. Segato

    2010-01-01

    Full Text Available The purpose of this work was to investigate the psychological stress present in elite sailors in a competition. Based on a descriptive field research, 31 elite sailors volunteered to participate. They answered the Perceived Stress Scale (Cohen & Williamson, 1988 and also specific questions on self-control, sources and strategies of coping. Data were analyzed by using descriptive and inferential (Student t test and Pearson's correlation statistics. These athletes revealed low and moderate scores (M = 20.00, DP = 6.83 of stress originated from both intrinsic (ship troubles, team disorders and extrinsic (study, working and training, family and financial problems sources. The group reported good stress control during competition through the use of cognitive (avoidance and somatic (listening music, resting/sleeping, talk to friends strategies. It is important that sailors are able to control and cope with high levels of psychological stress and to understand how to proceed when under unstable and unexpected situations that arise during competition.

  18. Exercise responses in patients with chronically high creatine kinase levels.

    Science.gov (United States)

    Cooper, Christopher B; Dolezal, Brett A; Neufeld, Eric V; Shieh, Perry; Jenner, John R; Riley, Marshall

    2017-08-01

    Elevated serum creatine kinase (CK) is often taken to reflect muscle disease, but many individuals have elevated CK without a specific diagnosis. How elevated CK reflects muscle metabolism during exercise is not known. Participants (46 men, 48 women) underwent incremental exercise testing to assess aerobic performance, cardiovascular response, and ventilatory response. Serum lactate, ammonia, and CK were measured at rest, 4 minutes into exercise, and 2 minutes into recovery. High-CK and control subjects demonstrated similar aerobic capacities and cardiovascular responses to incremental exercise. Those with CK ≥ 300 U/L exhibited significantly higher lactate and ammonia levels after maximal exercise, together with increased ventilatory responses, whereas those with CK ≥200 U/L but ≤ 300 U/L did not. We recommend measurement of lactate and ammonia profiles during a maximal incremental exercise protocol to help identify patients who warrant muscle biopsy to rule out myopathy. Muscle Nerve 56: 264-270, 2017. © 2016 Wiley Periodicals, Inc.

  19. First online experiences with the ALICE high level trigger

    Energy Technology Data Exchange (ETDEWEB)

    Alt, T.; Kisel, I.; Lindenstruth, V.; Painke, F.; Peschek, J.; Steinbeck, T.M.; Thaeder, J. [Kirchhoff Inst. of Physics, Ruprecht-Karls-Univ. Heidelberg (Germany); Bablok, S.; Haaland, Oe.; Richter, M.; Roehrich, D.; Oevrebek, G. [Inst. for Physics and Technology, Univ. of Bergen (Norway); Popescu, S. [CERN, Geneva (Switzerland)

    2007-07-01

    During the second half of 2006 the commissioning of the ALICE TPC has been performed using both cosmic and laser events. During this commissioning the high level trigger was operational with real data for the first time. Five Linux PCs were used to receive data from six TPC readout partitions from one sector under test. On the PCs the readout of the data was performed using the software components and PCI hardware to be used during ALICE running. After readout online event reconstruction involving cluster-finding and tracking of trajectories in the examined sector was then performed. Raw data as well as the reconstructed data were then sent to an online event display. This was then used to show the reconstructed events in different views. Included were a full 3D view of the detector, different raw data displays, and some histograms. In this talk we will present some of the experiences made during this first operational use of the ALICE HLT. (orig.)

  20. Commissioning and first experiences of the ALICE High Level Trigger

    Energy Technology Data Exchange (ETDEWEB)

    Steinbeck, Timm M, E-mail: timm.steinbeck@kip.uni-heidelberg.d [Kirchhoff Institute of Physics, University Heidelberg, im Neuenheimer Feld 227, D-69120 Heidelberg (Germany)

    2010-04-01

    For the ALICE heavy-ion experiment a large computing cluster will be used to perform the last triggering stages in the High Level Trigger (HLT). For the first year of operation the cluster consisted of about 100 multi-processing nodes with 4 or 8 CPU cores each, to be increased to more than 1000 nodes for the coming years of operation. During the commissioning phases of the detector, the preparations for first LHC beam, as well as during the periods of first LHC beam, the HLT has been used extensively already to reconstruct, compress, and display data from the different detectors. For example the HLT has been used to compress Silicon Drift Detector (SDD) data by a factor of 15, lossless, on the fly at a rate of more than 800 Hz. For ALICE's Time Projection Chamber (TPC) detector the HLT has been used to reconstruct tracks online and show the reconstructed tracks in an online event display. The event display can also display online reconstructed data from the Dimuon and Photon Spectrometer (PHOS) detectors. For the latter detector a first selection mechanism has also been put into place to select only events for forwarding to the online display in which data has passed through the PHOS detector. In this contribution we will present experiences and results from these commissioning phases.

  1. An FPGA based Preprocessor for the ALICE high level trigger

    Energy Technology Data Exchange (ETDEWEB)

    Alt, T.; Lindenstruth, V.; Painke, F.; Peschek, J.; Steinbeck, T.M. [Kirchhoff Inst. of Physics, Ruprecht-Karls-Univ., Heidelberg (Germany)

    2007-07-01

    The H-RORC (High Level Trigger ReadOut Receiver Card) is an FPGA based PCI card designed to receive raw detector data from ALICE, transfer it into the online processing framework of the HLT cluster farm and transmit the processed data out of the HLT to the DAQ. Each RORC can be equipped with two optical receiver/transmitter units and transfer up to 400 Mbyte/s via PCI. For online processing in hardware the Virtex4 LX40 FPGA is supported by four independent modules of fast DDR-SDRAM providing up to 512 Mbyte total storage at a bandwidth of 2.3 Gbyte/s and two fast serial, full-duplex links which can be used as an direct interconnect in order to exchange data between several RORCs. In replay mode the onboard memory can be loaded with real or simulated events thus giving a real-time test-bench for the HLT framework. A special configuration scheme suits the requirements of a cluster environment and allows a safe and remote upgrade of the firmware. The H-RORC was used successfully in the first time run of the HLT during the TPC commissioning 2006. (orig.)

  2. High Level Trigger Applications for the ALICE Experiment

    Science.gov (United States)

    Richter, M.; Aamodt, K.; Alt, T.; Bablok, S.; Cheshkov, C.; Hille, P. T.; Lindenstruth, V.; Ovrebekk, G.; Ploskon, M.; Popescu, S.; Rohrich, D.; Steinbeck, T. M.; Thader, J.

    2008-02-01

    For the ALICE experiment at the Large Hadron Collider (LHC) at CERN/Geneva, a high level trigger system (HLT) for online event selection and data compression has been developed and a computing cluster of several hundred dual-processor nodes is being installed. A major system integration test was carried out during the commissioning of the time projection chamber (TPC), where the HLT also provides a monitoring system. All major parts like a small computing cluster, hardware input devices, the online data transportation framework, and the HLT analysis could be tested successfully. A common interface for HLT processing components has been designed to run the components from either the online or offline analysis framework without changes. The interface adapts the component to the needs of the online processing and allows the developer to use the offline framework for easy development, debugging, and benchmarking. Following this approach, results can be compared directly. For the upcoming commissioning of the whole detector, the HLT is currently prepared to run online data analysis for the main detectors, e.g., the inner tracking system (ITS), the TPC, and the transition radiation detector (TRD). The HLT processing capability is indispensable for the photon spectrometer (PHOS), where the online pulse shape analysis reduces the data volume by a factor 20. A common monitoring framework is in place and detector calibration algorithms have been ported to the HLT. The paper describes briefly the architecture of the HLT system. It focuses on typical applications and component development.

  3. Commissioning and first experiences of the ALICE High Level Trigger

    Science.gov (United States)

    Steinbeck, Timm M.; Alice Hlt Collaboration

    2010-04-01

    For the ALICE heavy-ion experiment a large computing cluster will be used to perform the last triggering stages in the High Level Trigger (HLT). For the first year of operation the cluster consisted of about 100 multi-processing nodes with 4 or 8 CPU cores each, to be increased to more than 1000 nodes for the coming years of operation. During the commissioning phases of the detector, the preparations for first LHC beam, as well as during the periods of first LHC beam, the HLT has been used extensively already to reconstruct, compress, and display data from the different detectors. For example the HLT has been used to compress Silicon Drift Detector (SDD) data by a factor of 15, lossless, on the fly at a rate of more than 800 Hz. For ALICE's Time Projection Chamber (TPC) detector the HLT has been used to reconstruct tracks online and show the reconstructed tracks in an online event display. The event display can also display online reconstructed data from the Dimuon and Photon Spectrometer (PHOS) detectors. For the latter detector a first selection mechanism has also been put into place to select only events for forwarding to the online display in which data has passed through the PHOS detector. In this contribution we will present experiences and results from these commissioning phases.

  4. Seasonal changes in stress indicators in high level football.

    Science.gov (United States)

    Faude, O; Kellmann, M; Ammann, T; Schnittker, R; Meyer, T

    2011-04-01

    This study aimed at describing changes in stress and performance indicators throughout a competitive season in high level football. 15 players (19.5±3.0 years, 181±5 cm, 75.7±9.0 kg) competing under professional circumstances were tested at baseline and 3 times during the season 2008/09 (in-season 1, 2, 3). Testing consisted of the Recovery-Stress Questionnaire for Athletes (Total Stress and Recovery score), vertical jump tests (counter movement and drop jump (DJ)), and a maximal ramp-like running test. Average match exposure was higher during a 3-weeks period prior to in-season 3 compared to in-season 1 and 2 (1.5 vs. 1 h/week, p=0.05). Total Stress score was elevated at in-season 1 and 2 compared to baseline (pcorrelated with the corresponding changes in Total Stress score (r=-0.55 and r=-0.61, pstress and a lack of recovery towards the end of a season might be indicated by psychometric deteriorations. © Georg Thieme Verlag KG Stuttgart · New York.

  5. Site suitability criteria for solidified high level waste repositories

    Energy Technology Data Exchange (ETDEWEB)

    Heckman, R.A.; Holdsworth, T.; Isherwood, D.; Towse, D.F.; Dayem, N.L.

    1979-04-03

    The NRC is developing a framework of regulations, criteria, and standards. Lawrence Livermore Laboratory provides broad technical support to the NRC for developing this regulatory framework, part of which involves site suitability criteria for solidified high-level wastes (SHLW). Both the regulatory framework and the technical base on which it rests have evolved in time. This document is the second report of the technical support project. It was issued as a draft working paper for a programmatic review held at LLL from August 16 to 18, 1977. It was printed and distributed solely as a briefing document on preliminary methodology and initial findings for the purpose of critical review by those in attendance. These briefing documents are being reprinted now in their original formats as UCID-series reports for the sake of the historical record. Analysis results have evolved as both the models and data base have changed. As a result, the methodology, models, and data base in this document are severely outmoded.

  6. THE HIGH LEVEL ACCESSION DIALOGUE FOR MACEDONIA: ADVANTAGES AND DISADVANTAGES

    Directory of Open Access Journals (Sweden)

    Mladen Karadjoski

    2015-04-01

    Full Text Available One of the strategic goals for the Republic of Macedonia is membership in the European Union. At the end of 2011, the Commission launched a so-called High Level Accession Dialogue for Macedonia, with a possibility to start the negotiations after the fulfillment of the Dialogue goals and benchmarks. For these reasons, the main goal of this paper will be to give an answer of the dilemma whether the Accession Dialogue for Macedonia is an accelerator of the entrance in the European Union, or is just a sophisticated tool for delay of the start of the negotiations for final accession. The expected results will correspond with the future EU plans for Macedonia, but also for the other Western Balkan countries, i.e. we will try to examine whether these countries have a realistic perspective for entrance in the European Union, or they are just a “declarative décor” for the vocabulary of the Brussels diplomats and member countries representatives. That will help to determine i.e. to try to predict the next steps of these countries, connected with the European integration, regardless of the actual constellation in the European Union concerning the Enlargement policy. The descriptive method, content analyses method, comparative method, but also the inductive and deductive methods will be used in this paper.

  7. Multiple Word-Length High-Level Synthesis

    Directory of Open Access Journals (Sweden)

    Coussy Philippe

    2008-01-01

    Full Text Available Abstract Digital signal processing (DSP applications are nowadays widely used and their complexity is ever growing. The design of dedicated hardware accelerators is thus still needed in system-on-chip and embedded systems. Realistic hardware implementation requires first to convert the floating-point data of the initial specification into arbitrary length data (finite-precision while keeping an acceptable computation accuracy. Next, an optimized hardware architecture has to be designed. Considering uniform bit-width specification allows to use traditional automated design flow. However, it leads to oversized design. On the other hand, considering non uniform bit-width specification allows to get a smaller circuit but requires complex design tasks. In this paper, we propose an approach that inputs a C/C++ specification. The design flow, based on high-level synthesis (HLS techniques, automatically generates a potentially pipeline RTL architecture described in VHDL. Both bitaccurate integer and fixed-point data types can be used in the input specification. The generated architecture uses components (operator, register, etc. that have different widths. The design constraints are the clock period and the throughput of the application. The proposed approach considers data word-length information in all the synthesis steps by using dedicated algorithms. We show in this paper the effectiveness of the proposed approach through several design experiments in the DSP domain.

  8. Multiple Word-Length High-Level Synthesis

    Directory of Open Access Journals (Sweden)

    Dominique Heller

    2008-09-01

    Full Text Available Digital signal processing (DSP applications are nowadays widely used and their complexity is ever growing. The design of dedicated hardware accelerators is thus still needed in system-on-chip and embedded systems. Realistic hardware implementation requires first to convert the floating-point data of the initial specification into arbitrary length data (finite-precision while keeping an acceptable computation accuracy. Next, an optimized hardware architecture has to be designed. Considering uniform bit-width specification allows to use traditional automated design flow. However, it leads to oversized design. On the other hand, considering non uniform bit-width specification allows to get a smaller circuit but requires complex design tasks. In this paper, we propose an approach that inputs a C/C++ specification. The design flow, based on high-level synthesis (HLS techniques, automatically generates a potentially pipeline RTL architecture described in VHDL. Both bitaccurate integer and fixed-point data types can be used in the input specification. The generated architecture uses components (operator, register, etc. that have different widths. The design constraints are the clock period and the throughput of the application. The proposed approach considers data word-length information in all the synthesis steps by using dedicated algorithms. We show in this paper the effectiveness of the proposed approach through several design experiments in the DSP domain.

  9. Defense High-Level Waste Leaching Mechanisms Program. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Mendel, J.E. (compiler)

    1984-08-01

    The Defense High-Level Waste Leaching Mechanisms Program brought six major US laboratories together for three years of cooperative research. The participants reached a consensus that solubility of the leached glass species, particularly solubility in the altered surface layer, is the dominant factor controlling the leaching behavior of defense waste glass in a system in which the flow of leachant is constrained, as it will be in a deep geologic repository. Also, once the surface of waste glass is contacted by ground water, the kinetics of establishing solubility control are relatively rapid. The concentrations of leached species reach saturation, or steady-state concentrations, within a few months to a year at 70 to 90/sup 0/C. Thus, reaction kinetics, which were the main subject of earlier leaching mechanisms studies, are now shown to assume much less importance. The dominance of solubility means that the leach rate is, in fact, directly proportional to ground water flow rate. Doubling the flow rate doubles the effective leach rate. This relationship is expected to obtain in most, if not all, repository situations.

  10. EUVE GO Survey: High Levels of User Satisfaction

    Science.gov (United States)

    Stroozas, B. A.

    2000-12-01

    This paper describes the results of a detailed customer survey of Guest Observers (GOs) for NASA's Extreme Ultraviolet Explorer (EUVE) astronomy satellite observatory. The purpose of the research survey was to (1) measure the levels of GO customer satisfaction with respect to EUVE observing services, and (2) compare the observing experiences of EUVE GOs with their experiences using other satellite observatories. This survey was conducted as a business research project -- part of the author's graduate work as an MBA candidate. A total sample of 38 respondents, from a working population of 101 "active" EUVE GOs, participated in this survey. The results, which provided a profile of the "typical" EUVE GO, showed in a statistically significant fashion that these GOs were more than satisfied with the available EUVE observing services. In fact, the sample GOs generally rated their EUVE observing experiences to be better than average as compared to their experiences as GOs on other missions. These relatively high satisfaction results are particularly pleasing to the EUVE Project which, given its significantly reduced staffing environment at U.C. Berkeley, has continued to do more with less. This paper outlines the overall survey process: the relevant background and previous research, the survey design and methodology, and the final results and their interpretation. The paper also points out some general limitations and weaknesses of the study, along with some recommended actions for the EUVE Project and for NASA in general. This work was funded by NASA/UCB Cooperative Agreement NCC5-138.

  11. Process Design Concepts for Stabilization of High Level Waste Calcine

    Energy Technology Data Exchange (ETDEWEB)

    T. R. Thomas; A. K. Herbst

    2005-06-01

    The current baseline assumption is that packaging ¡§as is¡¨ and direct disposal of high level waste (HLW) calcine in a Monitored Geologic Repository will be allowed. The fall back position is to develop a stabilized waste form for the HLW calcine, that will meet repository waste acceptance criteria currently in place, in case regulatory initiatives are unsuccessful. A decision between direct disposal or a stabilization alternative is anticipated by June 2006. The purposes of this Engineering Design File (EDF) are to provide a pre-conceptual design on three low temperature processes under development for stabilization of high level waste calcine (i.e., the grout, hydroceramic grout, and iron phosphate ceramic processes) and to support a down selection among the three candidates. The key assumptions for the pre-conceptual design assessment are that a) a waste treatment plant would operate over eight years for 200 days a year, b) a design processing rate of 3.67 m3/day or 4670 kg/day of HLW calcine would be needed, and c) the performance of waste form would remove the HLW calcine from the hazardous waste category, and d) the waste form loadings would range from about 21-25 wt% calcine. The conclusions of this EDF study are that: (a) To date, the grout formulation appears to be the best candidate stabilizer among the three being tested for HLW calcine and appears to be the easiest to mix, pour, and cure. (b) Only minor differences would exist between the process steps of the grout and hydroceramic grout stabilization processes. If temperature control of the mixer at about 80„aC is required, it would add a major level of complexity to the iron phosphate stabilization process. (c) It is too early in the development program to determine which stabilizer will produce the minimum amount of stabilized waste form for the entire HLW inventory, but the volume is assumed to be within the range of 12,250 to 14,470 m3. (d) The stacked vessel height of the hot process vessels

  12. Depositional ice nucleation on solid ammonium sulfate and glutaric acid particles

    Directory of Open Access Journals (Sweden)

    K. J. Baustian

    2010-03-01

    Full Text Available Heterogeneous ice nucleation on solid ammonium sulfate and glutaric acid particles was studied using optical microscopy and Raman spectroscopy. Optical microscopy was used to detect selective nucleation events as water vapor was slowly introduced into an environmental sample cell. Particles that nucleated ice were dried via sublimation and examined in detail using Raman spectroscopy. Depositional ice nucleation is highly selective and occurred preferentially on just a few ammonium sulfate and glutaric acid particles in each sample. For freezing temperatures between 214 K and 235 K an average ice saturation ratio of S = 1.10±0.07 for solid ammonium sulfate was observed. Over the same temperature range, S values observed for ice nucleation on glutaric acid particles increased from 1.2 at 235 K to 1.6 at 218 K. Experiments with externally mixed particles further show that ammonium sulfate is a more potent ice nucleus than glutaric acid. Our results suggest that heterogeneous nucleation on ammonium sulfate may be an important pathway for atmospheric ice nucleation and cirrus cloud formation when solid ammonium sulfate aerosol particles are available for ice formation. This pathway for ice formation may be particularly significant near the tropical tropopause region where sulfates are abundant and other species known to be good ice nuclei are depleted.

  13. Neuromuscular onset succession of high level gymnasts during dynamic leg acceleration phases on high bar.

    Science.gov (United States)

    von Laßberg, Christoph; Rapp, Walter; Mohler, Betty; Krug, Jürgen

    2013-10-01

    In several athletic disciplines there is evidence that for generating the most effective acceleration of a specific body part the transfer of momentum should run in a "whip-like" consecutive succession of body parts towards the segment which shall be accelerated most effectively (e.g. the arm in throwing disciplines). This study investigated the question how this relates to the succession of neuromuscular activation to induce such "whip like" leg acceleration in sports like gymnastics with changed conditions concerning the body position and momentary rotational axis of movements (e.g. performing giant swings on high bar). The study demonstrates that during different long hang elements, performed by 12 high level gymnasts, the succession of the neuromuscular activation runs primarily from the bar (punctum fixum) towards the legs (punctum mobile). This demonstrates that the frequently used teaching instruction, first to accelerate the legs for a successful realization of such movements, according to a high level kinematic output, is contradictory to the neuromuscular input patterns, being used in high level athletes, realizing these skills with high efficiency. Based on these findings new approaches could be developed for more direct and more adequate teaching methods regarding to an earlier optimization and facilitation of fundamental movement requirements.

  14. Reusable, Extensible High-Level Data-Distribution Concept

    Science.gov (United States)

    James, Mark; Zima, Hans; Diaconescua, Roxana

    2007-01-01

    A framework for high-level specification of data distributions in data-parallel application programs has been conceived. [As used here, distributions signifies means to express locality (more specifically, locations of specified pieces of data) in a computing system composed of many processor and memory components connected by a network.] Inasmuch as distributions exert a great effect on the performances of application programs, it is important that a distribution strategy be flexible, so that distributions can be adapted to the requirements of those programs. At the same time, for the sake of productivity in programming and execution, it is desirable that users be shielded from such error-prone, tedious details as those of communication and synchronization. As desired, the present framework enables a user to refine a distribution type and adjust it to optimize the performance of an application program and conceals, from the user, the low-level details of communication and synchronization. The framework provides for a reusable, extensible, data-distribution design, denoted the design pattern, that is independent of a concrete implementation. The design pattern abstracts over coding patterns that have been found to be commonly encountered in both manually and automatically generated distributed parallel programs. The following description of the present framework is necessarily oversimplified to fit within the space available for this article. Distributions are among the elements of a conceptual data-distribution machinery, some of the other elements being denoted domains, index sets, and data collections (see figure). Associated with each domain is one index set and one distribution. A distribution class interface (where "class" is used in the object-oriented-programming sense) includes operations that enable specification of the mapping of an index to a unit of locality. Thus, "Map(Index)" specifies a unit, while "LocalLayout(Index)" specifies the local address

  15. PRN 88-2: Clustering of Quaternary Ammonium Compounds

    Science.gov (United States)

    This Notice announces that EPA has clustered the Quaternary Ammonium Compounds into four groups for the purpose of testing chemicals to build a database that will support continued registration of the entire family of quaternary ammonium compounds

  16. Ladderanes as tracers for present and past anaerobic ammonium oxidation

    NARCIS (Netherlands)

    Rush, D.J.

    2012-01-01

    Ladderane lipids are membrane lipids produced exclusively by anaerobic ammonium oxidising (anammox) bacteria. Anammox bacteria are key players in the marine nitrogen cycle, performing the anammox reaction, converting equal parts of ammonium and nitrite into dinitrogen gas. This process is

  17. Electric Grid Expansion Planning with High Levels of Variable Generation

    Energy Technology Data Exchange (ETDEWEB)

    Hadley, Stanton W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); You, Shutang [Univ. of Tennessee, Knoxville, TN (United States); Shankar, Mallikarjun [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Liu, Yilu [Univ. of Tennessee, Knoxville, TN (United States); Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2016-02-01

    Renewables are taking a large proportion of generation capacity in U.S. power grids. As their randomness has increasing influence on power system operation, it is necessary to consider their impact on system expansion planning. To this end, this project studies the generation and transmission expansion co-optimization problem of the US Eastern Interconnection (EI) power grid with a high wind power penetration rate. In this project, the generation and transmission expansion problem for the EI system is modeled as a mixed-integer programming (MIP) problem. This study analyzed a time series creation method to capture the diversity of load and wind power across balancing regions in the EI system. The obtained time series can be easily introduced into the MIP co-optimization problem and then solved robustly through available MIP solvers. Simulation results show that the proposed time series generation method and the expansion co-optimization model and can improve the expansion result significantly after considering the diversity of wind and load across EI regions. The improved expansion plan that combines generation and transmission will aid system planners and policy makers to maximize the social welfare. This study shows that modelling load and wind variations and diversities across balancing regions will produce significantly different expansion result compared with former studies. For example, if wind is modeled in more details (by increasing the number of wind output levels) so that more wind blocks are considered in expansion planning, transmission expansion will be larger and the expansion timing will be earlier. Regarding generation expansion, more wind scenarios will slightly reduce wind generation expansion in the EI system and increase the expansion of other generation such as gas. Also, adopting detailed wind scenarios will reveal that it may be uneconomic to expand transmission networks for transmitting a large amount of wind power through a long distance

  18. PLUTONIUM/HIGH-LEVEL VITRIFIED WASTE BDBE DOSE CALCULATION

    Energy Technology Data Exchange (ETDEWEB)

    D.C. Richardson

    2003-03-19

    In accordance with the Nuclear Waste Policy Amendments Act of 1987, Yucca Mountain was designated as the site to be investigated as a potential repository for the disposal of high-level radioactive waste. The Yucca Mountain site is an undeveloped area located on the southwestern edge of the Nevada Test Site (NTS), about 100 miles northwest of Las Vegas. The site currently lacks rail service or an existing right-of-way. If the Yucca Mountain site is found suitable for the repository, rail service is desirable to the Office of Civilian Waste Management (OCRWM) Program because of the potential of rail transportation to reduce costs and to reduce the number of shipments relative to highway transportation. A Preliminary Rail Access Study evaluated 13 potential rail spur options. Alternative routes within the major options were also developed. Each of these options was then evaluated for potential land use conflicts and access to regional rail carriers. Three potential routes having few land use conflicts and having access to regional carriers were recommended for further investigation. Figure 1-1 shows these three routes. The Jean route is estimated to be about 120 miles long, the Carlin route to be about 365 miles long, and Caliente route to be about 365 miles long. The remaining ten routes continue to be monitored and should any of the present conflicts change, a re-evaluation of that route will be made. Complete details of the evaluation of the 13 routes can be found in the previous study. The DOE has not identified any preferred route and recognizes that the transportation issues need a full and open treatment under the National Environmental Policy Act. The issue of transportation will be included in public hearings to support development of the Environmental Impact Statement (EIS) proceedings for either the Monitored Retrievable Storage Facility or the Yucca Mountain Project or both.

  19. High-Level Waste Systems Plan. Revision 7

    Energy Technology Data Exchange (ETDEWEB)

    Brooke, J.N.; Gregory, M.V.; Paul, P.; Taylor, G.; Wise, F.E.; Davis, N.R.; Wells, M.N.

    1996-10-01

    This revision of the High-Level Waste (HLW) System Plan aligns SRS HLW program planning with the DOE Savannah River (DOE-SR) Ten Year Plan (QC-96-0005, Draft 8/6), which was issued in July 1996. The objective of the Ten Year Plan is to complete cleanup at most nuclear sites within the next ten years. The two key principles of the Ten Year Plan are to accelerate the reduction of the most urgent risks to human health and the environment and to reduce mortgage costs. Accordingly, this System Plan describes the HLW program that will remove HLW from all 24 old-style tanks, and close 20 of those tanks, by 2006 with vitrification of all HLW by 2018. To achieve these goals, the DWPF canister production rate is projected to climb to 300 canisters per year starting in FY06, and remain at that rate through the end of the program in FY18, (Compare that to past System Plans, in which DWPF production peaked at 200 canisters per year, and the program did not complete until 2026.) An additional $247M (FY98 dollars) must be made available as requested over the ten year planning period, including a one-time $10M to enhance Late Wash attainment. If appropriate resources are made available, facility attainment issues are resolved and regulatory support is sufficient, then completion of the HLW program in 2018 would achieve a $3.3 billion cost savings to DOE, versus the cost of completing the program in 2026. Facility status information is current as of October 31, 1996.

  20. Level 1 Tornado PRA for the High Flux Beam Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Bozoki, G.E.; Conrad, C.S.

    1994-05-01

    This report describes a risk analysis primarily directed at providing an estimate for the frequency of tornado induced damage to the core of the High Flux Beam Reactor (HFBR), and thus it constitutes a Level 1 Probabilistic Risk Assessment (PRA) covering tornado induced accident sequences. The basic methodology of the risk analysis was to develop a ``tornado specific`` plant logic model that integrates the internal random hardware failures with failures caused externally by the tornado strike and includes operator errors worsened by the tornado modified environment. The tornado hazard frequency, as well as earlier prepared structural and equipment fragility data, were used as input data to the model. To keep modeling/calculational complexity as simple as reasonable a ``bounding`` type, slightly conservative, approach was applied. By a thorough screening process a single dominant initiating event was selected as a representative initiator, defined as: ``Tornado Induced Loss of Offsite Power.`` The frequency of this initiator was determined to be 6.37E-5/year. The safety response of the HFBR facility resulted in a total Conditional Core Damage Probability of .621. Thus, the point estimate of the HFBR`s Tornado Induced Core Damage Frequency (CDF) was found to be: (CDF){sub Tornado} = 3.96E-5/year. This value represents only 7.8% of the internal CDF and thus is considered to be a small contribution to the overall facility risk expressed in terms of total Core Damage Frequency. In addition to providing the estimate of (CDF){sub Tornado}, the report documents, the relative importance of various tornado induced system, component, and operator failures that contribute most to (CDF){sub Tornado}.

  1. Do mothers with high sodium levels in their breast milk have high depression and anxiety scores?

    Science.gov (United States)

    Serim Demirgoren, Burcu; Ozbek, Aylin; Ormen, Murat; Kavurma, Canem; Ozer, Esra; Aydın, Adem

    2017-04-01

    Objective This study aimed to assess the possible association of high breast milk sodium levels with postpartum depression and anxiety. Methods A total of 150 mothers and their healthy, exclusively breastfed newborns aged 8 to 15 days were recruited. Mothers were asked to complete scales for evaluation of postnatal depression and anxiety following an interview for consent and sociodemographic data collection. Breast milk samples were obtained to measure sodium and potassium (K) levels. Results Forty-nine mothers had higher than expected breast milk Na concentrations and a high Na/K ratio. These mothers scored significantly higher on the scales of postnatal depression and state anxiety ( P = 0.018 and P = 0.048, respectively). Conclusions This study shows that compared to normal breast milk Na levels and Na/K ratio, high breast milk Na and high Na/K ratio, with possible serious consequences in infants, are associated with maternal depressive and anxious symptoms in the postpartum period.

  2. Purification of IgG from serum with caprylic acid and ammonium sulphate precipitation is not superior to ammonium sulphate precipitation alone.

    Science.gov (United States)

    Mohanty, J G; Elazhary, Y

    1989-01-01

    Immunoglobulin G (IgG) from bovine serum raised against Aeromonas Salmonicida was purified by ammonium sulphate precipitation (ASP) or caprylic acid treatment followed by ammonium sulphate precipitation (CAAS). Purity of IgG samples prepared by both methods were examined by High Performance Gel Permeation Chromatography, electrophoresis and antibody activity assay. Results suggest that IgG prepared by ASP is better than that obtained by CAAS method in terms of the yield of the IgG monomers and the recovery of the antibody activity.

  3. 21 CFR 184.1296 - Ferric ammonium citrate.

    Science.gov (United States)

    2010-04-01

    ... citrate (iron (III) ammonium citrate) is prepared by the reaction of ferric hydroxide with citric acid, followed by treatment with ammonium hydroxide, evaporating, and drying. The resulting product occurs in two forms depending on the stoichiometry of the initial reactants. (1) Ferric ammonium citrate (iron...

  4. 21 CFR 184.1141b - Ammonium phosphate, dibasic.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ammonium phosphate, dibasic. 184.1141b Section 184... Listing of Specific Substances Affirmed as GRAS § 184.1141b Ammonium phosphate, dibasic. (a) Ammonium phosphate, dibasic ((NH4)2HPO4, CAS Reg. No. 7783-28-0) is manufactured by reacting ammonia with...

  5. 21 CFR 172.165 - Quaternary ammonium chloride combination.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Quaternary ammonium chloride combination. 172.165... HUMAN CONSUMPTION Food Preservatives § 172.165 Quaternary ammonium chloride combination. The food additive, quaternary ammonium chloride combination, may be safely used in food in accordance with...

  6. 78 FR 32690 - Certain Ammonium Nitrate From Ukraine

    Science.gov (United States)

    2013-05-31

    ... COMMISSION Certain Ammonium Nitrate From Ukraine Determination On the basis of the record \\1\\ developed in... antidumping duty order on certain ammonium nitrate from Ukraine would be likely to lead to continuation or... Publication 4396 (May 2013), entitled Certain Ammonium Nitrate from Ukraine: Investigation No....

  7. Further laboratory and theoretical investigations of ammonium dinitramide

    Energy Technology Data Exchange (ETDEWEB)

    Tulis, A.J.; Snelson, A. [IIT Research Institut, Chicago (United States); Heberlein, C.; Patel, D.L. [U.S. Army Cecom RD et E Center, NVESD (United States)

    1996-12-31

    Hydrogen and deuterated ammonium dinitramide have been vaporized under high vacuum and the IR matrix isolation spectra of the decomposition products obtained. Tentative vibration assignments have been made for HN(NO{sub 2}){sub 2} and DN(NO{sub 2}){sub 2} assuming a symmetrical non-planar structure in which the H or D is bonded to the central nitrogen atom. Other structures are also possible. Ab initio calculations have been made for the various structural isomers of hydrogen dinitramide. Vibration frequencies calculated for the hydrogenated and deuterated species are compared with the experimental values with the object of identifying the molecules` structure. (authors) 3 refs.

  8. Molecular characterization, function and regulation of ammonium transporters (Amt) and ammonium-metabolizing enzymes (GS, NADP-GDH) in the ectomycorrhizal fungus Hebeloma cylindrosporum.

    Science.gov (United States)

    Javelle, Arnaud; Morel, Mélanie; Rodríguez-Pastrana, Blanca-Rosa; Botton, Bernard; André, Bruno; Marini, Anne-Marie; Brun, Annick; Chalot, Michel

    2003-01-01

    External hyphae, which play a key role in nitrogen nutrition of trees, are considered as the absorbing structures of the ectomycorrhizal symbiosis. Here, we have cloned and characterized Hebeloma cylindrosporum AMT1, GLNA and GDHA genes, which encode a third ammonium transporter, a glutamine synthetase and an NADP-dependent glutamate dehydrogenase respectively. Amt1 can fully restore the pseudohyphal growth defect of a Saccharomyces cerevisiae mep2 mutant, and this is the first evidence that a heterologous member of the Mep/Amt family complements this dimorphic change defect. Dixon plots of the inhibition of methylamine uptake by ammonium indicate that Amt1 has a much higher affinity than the two previously characterized members (Amt2 and Amt3) of the Amt/Mep family in H. cylindrosporum. We also identified the intracellular nitrogen pool(s) responsible for the modulation of expression of AMT1, AMT2, AMT3, GDHA and GLNA. In response to exogenously supplied ammonium or glutamine, AMT1, AMT2 and GDHA were downregulated and, therefore, these genes are subjected to nitrogen repression in H. cylindrosporum. Exogenously supplied nitrate failed to induce a downregulation of the five mRNAs after transfer of mycelia from a N-starved condition. Our results demonstrate that glutamine is the main effector for AMT1 and AMT2 repression, whereas GDHA repression is controlled by intracellular ammonium, independently of the intracellular glutamine or glutamate concentration. Ammonium transport activity may be controlled by intracellular NH4+. AMT3 and GLNA are highly expressed but not highly regulated. A model for ammonium assimilation in H. cylindrosporum is presented.

  9. Extract of mangosteen increases high density lipoprotein levels in rats fed high lipid

    Directory of Open Access Journals (Sweden)

    Dwi Laksono Adiputro

    2015-12-01

    Full Text Available BACKGROUND In cardiovascular medicine, Garcinia mangostana has been used as an antioxidant to inhibit oxidation of low density lipoproteins and as an antiobesity agent. The effect of Garcinia mangostana on hyperlipidemia is unknown. The aim of this study was to evaluate the effect of an ethanolic extract of Garcinia mangostana pericarp on lipid profile in rats fed a high lipid diet. METHODS A total of 40 rats were divided into five groups control, high lipid diet, and high lipid diet + ethanolic extract of Garcinia mangostana pericarp at dosages of 200, 400, and 800 mg/kg body weight. The control group received a standard diet for 60 days. The high lipid diet group received standard diet plus egg yolk, goat fat, cholic acid, and pig fat for 60 days with or without ethanolic extract of Garcinia mangostana pericarp by the oral route. After 60 days, rats were anesthesized with ether for collection of blood by cardiac puncture. Analysis of blood lipid profile comprised colorimetric determination of cholesterol, triglyceride, low density lipoprotein (LDL, and high density lipoprotein (HDL. RESULTS From the results of one-way ANOVA it was concluded that there were significant between-group differences in cholesterol, trygliceride, LDL, and HDL levels (p=0.000. Ethanolic extract of Garcinia mangostana pericarp significantly decreased cholesterol, trygliceride, and LDL levels, starting at 400 mg/kg body weight (p=0.000. Ethanolic extract of Garcinia mangostana pericarp significantly increased HDL level starting at 200 mg/kg body weight (p=0.000. CONCLUSION Ethanolic extract of Garcinia mangostana pericarp has a beneficial effect on lipid profile in rats on a high lipid diet.

  10. Preparation and characterization of WO3 from ammonium paratungstate via hydrothermal method

    Institute of Scientific and Technical Information of China (English)

    Li Xiancai; Cao Xiaohua; Wang Wenjuan; Yang Yifeng; Rao Guohua

    2006-01-01

    Tungsten trioxide powder has been prepared from ammonium paratungstate via hydrothermal method using orthogonal and mono-level design of experiments.The effects of preparation process on particle size,specific surface area,crystal form and crystalline morphology of the tungsten trioxide was investigated by TEM and XRD etc.It was found that the optimum conditions of the preparation are hydrothermal crystallization for 8 h at 180℃,followed by vacuum drying at 45℃ and calcination at 500℃ for 2 h.The blank reference experiment shows that hydrothermal crystallization treatment favors the formation of hexagonal tungsten trioxide,and the tungsten trioxide powder sample prepared by this method has a high degree of crystallinity.

  11. Effects of ammonium lactate on 2,3-pentanedione formation from lactic acid

    Energy Technology Data Exchange (ETDEWEB)

    Tam, M.S.; Jackson, J.E.; Miller, D.J.

    1999-10-01

    Ammonia is often used for pH adjustment during fermentation of glucose to lactic acid. Its presence as ammonium lactate in the catalytic upgrading of lactic acid to 2,3-pentanedione over CsOH/silica reduces diketone yields to nearly zero at high ammonia levels. Removal of ammonia from the feed restores 2,3-pentanedione yield, indicating that the catalyst itself is not poisoned by ammonia. Instead, 2,3-pentanedione continues to form in the presence of ammonia and is consumed in secondary reactions downstream of the catalyst bed. Both base-catalyzed self-condensation of 2,3-pentanedione to duroquinone (and oligomeric species) and direct reaction of ammonia with the diketone are observed.

  12. High level waste interim storge architecture selection - decision report

    Energy Technology Data Exchange (ETDEWEB)

    Calmus, R.B.

    1996-09-27

    The U.S. Department of Energy (DOE) has embarked upon a course to acquire Hanford Site tank waste treatment and immobilization services using privatized facilities (RL 1996a). This plan contains a two-phased approach. Phase I is a proof-of-principle/connnercial demonstration- scale effort and Phase II is a fiill-scale production effort. In accordance with the planned approach, interim storage and disposal of various products from privatized facilities are to be DOE fumished. The high-level waste (BLW) interim storage options, or alternative architectures, were identified and evaluated to provide the framework from which to select the most viable method of Phase I BLW interim storage (Calmus 1996). This evaluation, hereafter referred to as the Alternative Architecture Evaluation, was performed to established performance and risk criteria (technical merit, cost, schedule, etc.). Based on evaluation results, preliminary architectures and path forward reconunendations were provided for consideration in the architecture decision- maldng process. The decision-making process used for selection of a Phase I solidified BLW interim storage architecture was conducted in accordance with an approved Decision Plan (see the attachment). This decision process was based on TSEP-07,Decision Management Procedure (WHC 1995). The established decision process entailed a Decision Board, consisting of Westinghouse Hanford Company (VY`HC) management staff, and included appointment of a VTHC Decision Maker. The Alternative Architecture Evaluation results and preliminary recommendations were presented to the Decision Board members for their consideration in the decision-making process. The Alternative Architecture Evaluation was prepared and issued before issuance of @C-IP- 123 1, Alternatives Generation and Analysis Procedure (WI-IC 1996a), but was deemed by the Board to fully meet the intent of WHC-IP-1231. The Decision Board members concurred with the bulk of the Alternative Architecture

  13. A high-speed DAQ framework for future high-level trigger and event building clusters

    Science.gov (United States)

    Caselle, M.; Ardila Perez, L. E.; Balzer, M.; Dritschler, T.; Kopmann, A.; Mohr, H.; Rota, L.; Vogelgesang, M.; Weber, M.

    2017-03-01

    Modern data acquisition and trigger systems require a throughput of several GB/s and latencies of the order of microseconds. To satisfy such requirements, a heterogeneous readout system based on FPGA readout cards and GPU-based computing nodes coupled by InfiniBand has been developed. The incoming data from the back-end electronics is delivered directly into the internal memory of GPUs through a dedicated peer-to-peer PCIe communication. High performance DMA engines have been developed for direct communication between FPGAs and GPUs using "DirectGMA (AMD)" and "GPUDirect (NVIDIA)" technologies. The proposed infrastructure is a candidate for future generations of event building clusters, high-level trigger filter farms and low-level trigger system. In this paper the heterogeneous FPGA-GPU architecture will be presented and its performance be discussed.

  14. High-Dimensional Topological Insulators with Quaternionic Analytic Landau Levels

    Science.gov (United States)

    Li, Yi; Wu, Congjun

    2013-05-01

    We study the three-dimensional topological insulators in the continuum by coupling spin-1/2 fermions to the Aharonov-Casher SU(2) gauge field. They exhibit flat Landau levels in which orbital angular momentum and spin are coupled with a fixed helicity. The three-dimensional lowest Landau level wave functions exhibit the quaternionic analyticity as a generalization of the complex analyticity of the two-dimensional case. Each Landau level contributes one branch of gapless helical Dirac modes to the surface spectra, whose topological properties belong to the Z2 class. The flat Landau levels can be generalized to an arbitrary dimension. Interaction effects and experimental realizations are also studied.

  15. The Influence of Decreased Levels of High Density Lipoprotein ...

    African Journals Online (AJOL)

    but the physiological ramifications of the low levels observed have not been entirely resolved. .... infection, major organs involvement, and number of times ..... Characteristics .... support among medical, dental, nursing students and doctors.

  16. Global transcriptional analysis of nitrogen fixation and ammonium repression in root-associated Pseudomonas stutzeri A1501

    Directory of Open Access Journals (Sweden)

    Lu Wei

    2010-01-01

    Full Text Available Abstract Background Biological nitrogen fixation is highly controlled at the transcriptional level by regulatory networks that respond to the availability of fixed nitrogen. In many diazotrophs, addition of excess ammonium in the growth medium results in immediate repression of nif gene transcription. Although the regulatory cascades that control the transcription of the nif genes in proteobacteria have been well investigated, there are limited data on the kinetics of ammonium-dependent repression of nitrogen fixation. Results Here we report a global transcriptional profiling analysis of nitrogen fixation and ammonium repression in Pseudomonas stutzeri A1501, a root-associated and nitrogen-fixing bacterium. A total of 166 genes, including those coding for the global nitrogen regulation (Ntr and Nif-specific regulatory proteins, were upregulated under nitrogen fixation conditions but rapidly downregulated as early as 10 min after ammonium shock. Among these nitrogen fixation-inducible genes, 95 have orthologs in each of Azoarcus sp. BH72 and Azotobacter vinelandii AvoP. In particular, a 49-kb expression island containing nif and other associated genes was markedly downregulated by ammonium shock. Further functional characterization of pnfA, a new NifA-σ54-dependent gene chromosomally linked to nifHDK, is reported. This gene encodes a protein product with an amino acid sequence similar to that of five hypothetical proteins found only in diazotrophic strains. No noticeable differences in the transcription of nifHDK were detected between the wild type strain and pnfA mutant. However, the mutant strain exhibited a significant decrease in nitrogenase activity under microaerobic conditions and lost its ability to use nitrate as a terminal electron acceptor for the support of nitrogen fixation under anaerobic conditions. Conclusions Based on our results, we conclude that transcriptional regulation of nif gene expression in A1501 is mediated by the nif

  17. N-Chlorotaurine and ammonium chloride: an antiseptic preparation with strong bactericidal activity.

    Science.gov (United States)

    Gottardi, Waldemar; Arnitz, Roland; Nagl, Markus

    2007-04-20

    The bactericidal activity of the endogenous antiseptic N-chlorotaurine (NCT) is significantly enhanced in the presence of ammonium chloride which induces the formation of monochloramine (NH(2)Cl) whose strong bactericidal activity is well known. In this study the properties of NCT plus ammonium chloride have been investigated. The reaction of active chlorine compounds like chloramine-T (N-chlorotoluene-sulfonamide sodium), chloroisocyanuric acid derivatives, hypochlorites (NaOCl, CaOCl(2)) with ammonium chloride did not stop at the stage of monochloramine, and the pungent smelling by-products di- and trichloramine, NHCl(2) and NCl(3), were also formed. This was not the case with NCT where only monochloramine was generated. The equilibrium constant of the reaction of NCT with ammonium was found to be [Formula: see text] , which allows to estimate the equilibrium concentration of monochloramine in aqueous solutions of NCT and ammonium chloride. At concentrations each ranging between 0.01% and 1.0% it comes to [NH(2)Cl]=3.5-254 ppm. As an unexpected result the monochloramine containing formulation turned out to be most stable in plain water without buffer additives. Quantitative killing assays revealed complete inactivation of 10(6) to 10(7)CFU/mL of seven bacterial strains by 0.1% NCT plus 0.1% ammonium chloride within 5 min, while with plain 0.1% NCT an incubation time of 2-4h was needed to achieve the same effect. The highly significant increase of bactericidal activity (200-300-fold) could be assigned to the presence of monochloramine which could be isolated by vacuum distillation. Aqueous solutions of NCT and ammonium chloride provide a highly effective and well tolerable antiseptic preparation appropriate to a treatment cycle of at least 1 month if stored in the refrigerator.

  18. Low copper and high manganese levels in prion protein plaques

    Science.gov (United States)

    Johnson, Christopher J.; Gilbert, P.U.P.A.; Abrecth, Mike; Baldwin, Katherine L.; Russell, Robin E.; Pedersen, Joel A.; McKenzie, Debbie

    2013-01-01

    Accumulation of aggregates rich in an abnormally folded form of the prion protein characterize the neurodegeneration caused by transmissible spongiform encephalopathies (TSEs). The molecular triggers of plaque formation and neurodegeneration remain unknown, but analyses of TSE-infected brain homogenates and preparations enriched for abnormal prion protein suggest that reduced levels of copper and increased levels of manganese are associated with disease. The objectives of this study were to: (1) assess copper and manganese levels in healthy and TSE-infected Syrian hamster brain homogenates; (2) determine if the distribution of these metals can be mapped in TSE-infected brain tissue using X-ray photoelectron emission microscopy (X-PEEM) with synchrotron radiation; and (3) use X-PEEM to assess the relative amounts of copper and manganese in prion plaques in situ. In agreement with studies of other TSEs and species, we found reduced brain levels of copper and increased levels of manganese associated with disease in our hamster model. We also found that the in situ levels of these metals in brainstem were sufficient to image by X-PEEM. Using immunolabeled prion plaques in directly adjacent tissue sections to identify regions to image by X-PEEM, we found a statistically significant relationship of copper-manganese dysregulation in prion plaques: copper was depleted whereas manganese was enriched. These data provide evidence for prion plaques altering local transition metal distribution in the TSE-infected central nervous system.

  19. Quaternary ammonium compounds – New occupational hazards

    Directory of Open Access Journals (Sweden)

    Agnieszka Lipińska-Ojrzanowska

    2014-10-01

    Full Text Available Quaternary ammonium compounds (QACs, quats belong to organic ionic chemical agents which display unique properties of both surfactants and disinfectants. Their wide distribution in the work environment and also in private households brings about new occupational hazards. This paper reviews reports about the health effects of QACs. QACs could play a role of sensitizers and irritants to the skin and mucous membranes. It is suspected that particular QACs can display an immunologic crossreactivity between each other and with other chemical compounds containing ammonium ion, such as muscle relaxants widely used in anesthesia. They may promote the development of airway allergy, however, the background mechanisms are still unclear and need to be further investigated. Until now, a few cases of occupational asthma induced by QACs have been described and their involvement in contact dermatitis has been documented. The possibility of anaphylaxis due to QACs cannot be excluded as well. Med Pr 2014;65(5:675–682

  20. To Break or to Brake Neuronal Network Accelerated by Ammonium Ions?

    Directory of Open Access Journals (Sweden)

    Vladimir V Dynnik

    Full Text Available The aim of present study was to investigate the effects of ammonium ions on in vitro neuronal network activity and to search alternative methods of acute ammonia neurotoxicity prevention.Rat hippocampal neuronal and astrocytes co-cultures in vitro, fluorescent microscopy and perforated patch clamp were used to monitor the changes in intracellular Ca2+- and membrane potential produced by ammonium ions and various modulators in the cells implicated in neural networks.Low concentrations of NH4Cl (0.1-4 mM produce short temporal effects on network activity. Application of 5-8 mM NH4Cl: invariably transforms diverse network firing regimen to identical burst patterns, characterized by substantial neuronal membrane depolarization at plateau phase of potential and high-amplitude Ca2+-oscillations; raises frequency and average for period of oscillations Ca2+-level in all cells implicated in network; results in the appearance of group of «run out» cells with high intracellular Ca2+ and steadily diminished amplitudes of oscillations; increases astrocyte Ca2+-signalling, characterized by the appearance of groups of cells with increased intracellular Ca2+-level and/or chaotic Ca2+-oscillations. Accelerated network activity may be suppressed by the blockade of NMDA or AMPA/kainate-receptors or by overactivation of AMPA/kainite-receptors. Ammonia still activate neuronal firing in the presence of GABA(A receptors antagonist bicuculline, indicating that «disinhibition phenomenon» is not implicated in the mechanisms of networks acceleration. Network activity may also be slowed down by glycine, agonists of metabotropic inhibitory receptors, betaine, L-carnitine, L-arginine, etc.Obtained results demonstrate that ammonium ions accelerate neuronal networks firing, implicating ionotropic glutamate receptors, having preserved the activities of group of inhibitory ionotropic and metabotropic receptors. This may mean, that ammonia neurotoxicity might be prevented by

  1. Quaternary ammonium salts with tetrafluoroborate anion: Phytotoxicity and oxidative stress in terrestrial plants

    Energy Technology Data Exchange (ETDEWEB)

    Biczak, Robert, E-mail: r.biczak@ajd.czest.pl

    2016-03-05

    Highlights: • The level of oxidative stress in mono- and dicotyledonous plants was comparable. • Chlorophyll content in the plants was correlated with QAS concentration in the soil. • POD activity increased in plants cultivated in soil with high QAS content. - Abstract: This paper discusses the impact of four quaternary ammonium salts (QAS) such as tetraethylammonium tetrafluoroborate [TEA][BF{sub 4}], tetrabutylammonium tetrafluoroborate [TBA][BF{sub 4}], tetrahexylammonium tetrafluoroborate [THA][BF{sub 4}], and tetraoctylammonium tetrafluoroborate [TOA][BF{sub 4}] on the growth and development of spring barley and common radish. Analogous tests were performed with the inorganic salt ammonium tetrafluoroborate [A][BF{sub 4}] for comparison purposes. Results indicated that the phytotoxicity of the QAS applied is dependent on the concentration of the substance and their number of carbon atoms. The most toxic compound was [TBA][BF{sub 4}], causing the greatest drop in fresh weight of both study plants, similar to the phytotoxic effects of [A][BF{sub 4}]. All the tested compounds caused oxidative stress in spring barley and common radish seedlings due to a drop in the chlorophyll content. Stress was also observed in plants, which was indicated by the increased level of ROS (reactive oxygen species) such as H{sub 2}O{sub 2} and lipid peroxidation of MDA (malondialdehyde). Due to the stress, both plants displayed changes in the activity of antioxidative enzymes such as superoxide dismutase (SOD), catalase (CAT) and peroxidase (POD). Based on the results of the study, it was concluded that changes in chlorophyll levels and peroxidase activity are the best biomarkers to determine oxidative stress in plants.

  2. The Rapid Emergence of High Level Gentamicin Resistance in Enterococci

    Directory of Open Access Journals (Sweden)

    Kevin R Forward

    1990-01-01

    Full Text Available The proportion of enterococci isolated from blood and urine cultures that were highly resistant to gentamicin and streptomycin were determined. No blood or urine isolates highly resistant to gentamicin were seen in 1983, whereas by 1986–87 25% of blood and 17% of urine isolates were highly resistant. The rapid emergence of gentamicin resistance has serious implications for patients with life threatening enterococcal disease.

  3. Efficient ozone, sulfate, and ammonium free resist stripping process

    Science.gov (United States)

    Dattilo, Davide; Dietze, Uwe

    2014-07-01

    In recent years, photomask resist strip and cleaning technology development was substantially driven by the industry's need to prevent surface haze formation through the elimination of sulfuric acid and ammonium hydroxide from these processes. As a result, conventional SPM (H2SO4 + H2O2) was replaced with Ozone water (DIO3) for resist stripping and organic removal to eliminate chemical haze formation [1, 2]. However, it has been shown that DIO3 basted strip and clean process causes oxidative degradation of photomask materials [3, 4]. Such material damage can affect optical properties of funcitional mask layers, causeing CD line-width, phase, transmission and reflection changes, adversely affecting image transfer during the Lithography process. To overcome Ozone induced surface damage, SUSS MicroTec successfully developed a highly efficient strip process, where photolysis of DIO3 is leading to highly reactive hydroxyl radical formation, as the main contribution to hydrocarbon removal without surface damage [5]. This technology has been further extended to a final clean process, which is utilizing pure DI water for residual organic material removal during final clean [6]. Recently, SUS MicroTec did also successfully release strip and clean processes which completely remove NH4OH, eliminating any chemicals known today to induce haze [7]. In this paper we show the benefits of these new technologies for highly efficient sulfate and ammonium free stripping and cleaning processes.

  4. Development of Crystal-Tolerant High-Level Waste Glasses

    Energy Technology Data Exchange (ETDEWEB)

    Matyas, Josef; Vienna, John D.; Schaible, Micah J.; Rodriguez, Carmen P.; Crum, Jarrod V.; Arrigoni, Alyssa L.; Tate, Rachel M.

    2010-12-17

    Twenty five glasses were formulated. They were batched from HLW AZ-101 simulant or raw chemicals and melted and tested with a series of tests to elucidate the effect of spinel-forming components (Ni, Fe, Cr, Mn, and Zn), Al, and noble metals (Rh2O3 and RuO2) on the accumulation rate of spinel crystals in the glass discharge riser of the high-level waste (HLW) melter. In addition, the processing properties of glasses, such as the viscosity and TL, were measured as a function of temperature and composition. Furthermore, the settling of spinel crystals in transparent low-viscosity fluids was studied at room temperature to access the shape factor and hindered settling coefficient of spinel crystals in the Stokes equation. The experimental results suggest that Ni is the most troublesome component of all the studied spinel-forming components producing settling layers of up to 10.5 mm in just 20 days in Ni-rich glasses if noble metals or a higher concentration of Fe was not introduced in the glass. The layer of this thickness can potentially plug the bottom of the riser, preventing glass from being discharged from the melter. The noble metals, Fe, and Al were the components that significantly slowed down or stopped the accumulation of spinel at the bottom. Particles of Rh2O3 and RuO2, hematite and nepheline, acted as nucleation sites significantly increasing the number of crystals and therefore decreasing the average crystal size. The settling rate of ≤10-μm crystal size around the settling velocity of crystals was too low to produce thick layers. The experimental data for the thickness of settled layers in the glasses prepared from AZ-101 simulant were used to build a linear empirical model that can predict crystal accumulation in the riser of the melter as a function of concentration of spinel-forming components in glass. The developed model predicts the thicknesses of accumulated layers quite well, R2 = 0.985, and can be become an efficient tool for the formulation

  5. Advanced High-Level Waste Glass Research and Development Plan

    Energy Technology Data Exchange (ETDEWEB)

    Peeler, David K. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Vienna, John D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Schweiger, Michael J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Fox, Kevin M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-07-01

    The U.S. Department of Energy Office of River Protection (ORP) has implemented an integrated program to increase the loading of Hanford tank wastes in glass while meeting melter lifetime expectancies and process, regulatory, and product quality requirements. The integrated ORP program is focused on providing a technical, science-based foundation from which key decisions can be made regarding the successful operation of the Hanford Tank Waste Treatment and Immobilization Plant (WTP) facilities. The fundamental data stemming from this program will support development of advanced glass formulations, key process control models, and tactical processing strategies to ensure safe and successful operations for both the low-activity waste (LAW) and high-level waste (HLW) vitrification facilities with an appreciation toward reducing overall mission life. The purpose of this advanced HLW glass research and development plan is to identify the near-, mid-, and longer-term research and development activities required to develop and validate advanced HLW glasses and their associated models to support facility operations at WTP, including both direct feed and full pretreatment flowsheets. This plan also integrates technical support of facility operations and waste qualification activities to show the interdependence of these activities with the advanced waste glass (AWG) program to support the full WTP mission. Figure ES-1 shows these key ORP programmatic activities and their interfaces with both WTP facility operations and qualification needs. The plan is a living document that will be updated to reflect key advancements and mission strategy changes. The research outlined here is motivated by the potential for substantial economic benefits (e.g., significant increases in waste throughput and reductions in glass volumes) that will be realized when advancements in glass formulation continue and models supporting facility operations are implemented. Developing and applying advanced

  6. High-performance gamma spectroscopy for equipment retrieval from Hanford high-level nuclear waste tanks

    Science.gov (United States)

    Troyer, Gary L.; Hillesand, K. E.; Goodwin, S. G.; Kessler, S. F.; Killian, E. W.; Legare, D.; Nelson, Joseph V., Jr.; Richard, R. F.; Nordquist, E. M.

    1999-01-01

    The cleanup of high level defense nuclear waste at the Hanford site presents several progressive challenges. Among these is the removal and disposal of various components from buried active waste tanks to allow new equipment insertion or hazards mitigation. A unique automated retrieval system at the tank provides for retrieval, high pressure washing, inventory measurement, and containment for disposal. Key to the inventory measurement is a three detector HPGe high performance gamma spectroscopy system capable of recovering data at up to ninety per cent saturation (200,000 counts per second). Data recovery is based on a unique embedded electronic pulser and specialized software to report the inventory. Each of the detectors have different shielding specified through Monte Carlo simulation with the MCNP program. This shielding provides performance over a dynamic range of eight orders of magnitude. System description, calibration issues and operational experiences are discussed.

  7. High antibody levels to P. gingivalis in cardiovascular disease.

    Science.gov (United States)

    Bohnstedt, S; Cullinan, M P; Ford, P J; Palmer, J E; Leishman, S J; Westerman, B; Marshall, R I; West, M J; Seymour, G J

    2010-09-01

    Recent evidence suggests that strain variation in the serum IgG response to Porphyromonas gingivalis occurs in periodontal disease and cardiovascular disease (CVD). This study aimed to test the hypothesis that different P. gingivalis strains would elicit different levels of IgG, depending on a patient's cardiovascular (CV) and periodontal health. For CVD patients, serum antibody levels increased significantly with increasing numbers of deep pockets for all strains of P. gingivalis, except W50 (p immune response to P. gingivalis in the relationship between periodontal disease and CVD.

  8. Research progress on molecular regulation of ammonium uptake and trans-port in plant%植物对铵态氮的吸收转运调控机制研究进展

    Institute of Scientific and Technical Information of China (English)

    刘婷; 尚忠林

    2016-01-01

    Ammonium is, besides nitrate, the most important nitrogen form being taken up and assimilated by root cells, while, over ammonium accumulation is toxic to plant cells. Thus, ammonium uptake process must be tightly controlled according to plant nitrogen status and external nitrogen availability. AMT-type ammonium transporters have been demonstrated to mediate high-afifnity ammonium uptake across the plasma membrane in roots, and AMT gene expression and its transport activities are strictly controlled on multilevel including tran-scription and translation levels. Here, research progress on plant ammonium uptake and transport mechanism is discussed, especially translational regulation in the recent ifve years.%铵作为重要的氮源被植物根系吸收并同化,但是过量的铵也会对细胞造成毒害。植物必须依据外界环境和自身氮水平来严格调控根系对铵的吸收过程。铵转运蛋白介导的高亲和力铵跨质膜运输是植物根系吸收铵的主要途径, AMT基因的表达及转运活性在转录和蛋白水平等多层面被严格调控。本文对于植物铵吸收和转运机制,尤其是近5年关于蛋白水平调控的最新研究进展进行了评述。

  9. New Generation Nuclear Plant -- High Level Functions and Requirements

    Energy Technology Data Exchange (ETDEWEB)

    J. M. Ryskamp; E. J. Gorski; E. A. Harvego; S. T. Khericha; G. A. Beitel

    2003-09-01

    This functions and requirements (F&R) document was prepared for the Next Generation Nuclear Plant (NGNP) Project. The highest-level functions and requirements for the NGNP preconceptual design are identified in this document, which establishes performance definitions for what the NGNP will achieve. NGNP designs will be developed based on these requirements by commercial vendor(s).

  10. False high level in total bilirubin estimation in nonicteric serum ...

    African Journals Online (AJOL)

    PROMOTING ACCESS TO AFRICAN RESEARCH ... International Journal of Biological and Chemical Sciences ... In day to day clinical biochemistry laboratory practices, occasionally abnormal levels of individual parameters are noted. ... of using very reliable and stable reagent kit from Roche in the biochemistry laboratory ...

  11. Production Cost Modeling for High Levels of Photovoltaics Penetration

    Energy Technology Data Exchange (ETDEWEB)

    Denholm, P.; Margolis, R.; Milford, J.

    2008-02-01

    The goal of this report is to evaluate the likely avoided generation, fuels, and emissions resulting from photovoltaics (PV) deployment in several U.S. locations and identify new tools, methods, and analysis to improve understanding of PV impacts at the grid level.

  12. Heavy metal levels in soil samples from highly industrialized Lagos ...

    African Journals Online (AJOL)

    Anyakora

    2013-09-05

    Sep 5, 2013 ... Cadmium and iron levels exceeded that of the European Regulatory ... to certain industrial activities has been on the rise in ... wastewater irrigation, coal combustion residues, spillage ..... excavation and land fill, thermal treatment, which are not .... Phytoextraction of toxic metals: a review of biological.

  13. System Specification for Immobilized High-Level Waste Interim Storage

    Energy Technology Data Exchange (ETDEWEB)

    CALMUS, R.B.

    2000-12-27

    This specification establishes the system-level functional, performance, design, interface, and test requirements for Phase 1 of the IHLW Interim Storage System, located at the Hanford Site in Washington State. The IHLW canisters will be produced at the Hanford Site by a Selected DOE contractor. Subsequent to storage the canisters will be shipped to a federal geologic repository.

  14. Alternative process to produce UF{sub 4} using the effluent from ammonium uranyl carbonate route

    Energy Technology Data Exchange (ETDEWEB)

    Silva Neto, Joao B.; Garcia, Rafael Henrique Lazzari; Dal Vechio, Edvaldo, E-mail: jbsneto@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), SP (Brazil); Riella, Humberto G., E-mail: riella@enq.ufsc.br [Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil); Instituto Nacional de Ciencias e Tecnologia de Reatores Nucleares Inovadores (INCT/CNPq) (Brazil); Carvalho, Elita F. Urano de; Durazzo, Michelangelo [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), SP (Brazil); Instituto Nacional de Ciencias e Tecnologia de Reatores Nucleares Inovadores (INCT/CNPq) (Brazil)

    2011-07-01

    The Nuclear Fuel Centre of IPEN / CNEN - SP develops and manufactures dispersion fuel with high uranium concentration. It meets the demand of the IEA-R1 reactor and future research reactors to be constructed in Brazil. The fuel uses uranium silicide (U{sub 3}Si{sub 2}) dispersed in aluminum. For producing the fuel, the process of uranium hexafluoride (UF{sub 6}) conversion consist in obtaining U{sub 3}Si{sub 2} and / or U{sub 3}O{sub 8} through the preparation of intermediate compounds, among them ammonium uranyl carbonate - AUC, ammonium diuranate - DUA and uranium tetrafluoride - UF{sub 4}. This work describes a procedure for preparing uranium tetrafluoride via a dry route, using as raw material the filtrate generated when ammonium uranyl carbonate is routinely produced. The filtrate consists mainly of a solution containing high concentrations of ammonium (NH{sup 4+}), fluoride (F{sup -}), carbonate (CO{sup 3-}) and low concentrations of uranium. The procedure consists in recovering NH{sup 4F} and uranium, as UF{sub 4}, through the crystallization of ammonium bifluoride (NH{sub 4}HF{sub 2}) and, in a later step, the addition of UO{sub 2}, occurring fluoridation and decomposition. The UF{sub 4} obtained is further diluted in the UF{sub 4} produced routinely at IPEN / CNEN-SP by a wet route process. (author)

  15. Regulation of length and density of Arabidopsis root hairs by ammonium and nitrate.

    Science.gov (United States)

    Vatter, Thomas; Neuhäuser, Benjamin; Stetter, Markus; Ludewig, Uwe

    2015-09-01

    Root hairs expand the effective root surface to increase the uptake of nutrients and water from the soil. Here the local effects of the two major nitrogen sources, ammonium and nitrate, on root hairs were investigated using split plates. In three contrasting accessions of A. thaliana, namely Col-0, Tsu-0 and Sha, root hairs were differentially affected by the nitrogen forms and their concentration. Root hairs in Sha were short in the absence of nitrate. In Col-0, hair length was moderately decreased with increasing nitrate or ammonium. In all accessions, the root hair density was insensitive to 1,000-fold changes in the ammonium concentrations, when supplied locally as the exclusive nitrogen form. In contrast, the root hair density generally increased with nitrate as the exclusive local nitrogen source. The nitrate sensitivity was reduced at mM concentrations in a loss-of-function mutant of the nitrate transporter and sensor gene NRT1;1 (NPF6.3). Little differences with respect to ammonium were found in a mutant lacking four high affinity AMT-type ammonium transporters, but interestingly, the response to high nitrate was reduced and may indicate a general defect in nitrogen signaling in that mutant. Genetic diversity and the presence of the nitrogen transceptor NRT1;1 explain heterogeneity in the responses of root hairs to different nitrogen forms in Arabidopsis accessions.

  16. Space Electronics Operating at High Temperatures and Radiation Levels Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The objective is to produce high efficiency DC/DC power modules in a small low profile package that can tolerate extreme environment conditions. The primary effort...

  17. A High-Throughput, High-Accuracy System-Level Simulation Framework for System on Chips

    Directory of Open Access Journals (Sweden)

    Guanyi Sun

    2011-01-01

    Full Text Available Today's System-on-Chips (SoCs design is extremely challenging because it involves complicated design tradeoffs and heterogeneous design expertise. To explore the large solution space, system architects have to rely on system-level simulators to identify an optimized SoC architecture. In this paper, we propose a system-level simulation framework, System Performance Simulation Implementation Mechanism, or SPSIM. Based on SystemC TLM2.0, the framework consists of an executable SoC model, a simulation tool chain, and a modeling methodology. Compared with the large body of existing research in this area, this work is aimed at delivering a high simulation throughput and, at the same time, guaranteeing a high accuracy on real industrial applications. Integrating the leading TLM techniques, our simulator can attain a simulation speed that is not slower than that of the hardware execution by a factor of 35 on a set of real-world applications. SPSIM incorporates effective timing models, which can achieve a high accuracy after hardware-based calibration. Experimental results on a set of mobile applications proved that the difference between the simulated and measured results of timing performance is within 10%, which in the past can only be attained by cycle-accurate models.

  18. Understanding the impact of the central atom on the ionic liquid behavior: Phosphonium vs ammonium cations

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, Pedro J.; Ventura, Sónia P. M.; Batista, Marta L. S.; Schröder, Bernd; Coutinho, João A. P., E-mail: jcoutinho@ua.pt [CICECO, Departamento de Química, Universidade de Aveiro, 3810-193 Aveiro (Portugal); Gonçalves, Fernando [Departamento de Biologia e CESAM (Centro de Estudos do Ambiente e do Mar), Universidade de Aveiro, 3810-193 Aveiro (Portugal); Esperança, José [Instituto de Tecnologia Química e Biológica, Universidade Nova de Lisboa, 2780-901 Oeiras (Portugal); Mutelet, Fabrice [Laboratoire Réactions et Génie des Procédés, CNRS (UPR3349), Nancy-Université, 1 rue Grandville, BP 20451 54001 Nancy (France)

    2014-02-14

    The influence of the cation's central atom in the behavior of pairs of ammonium- and phosphonium-based ionic liquids was investigated through the measurement of densities, viscosities, melting temperatures, activity coefficients at infinite dilution, refractive indices, and toxicity against Vibrio fischeri. All the properties investigated are affected by the cation's central atom nature, with ammonium-based ionic liquids presenting higher densities, viscosities, melting temperatures, and enthalpies. Activity coefficients at infinite dilution show the ammonium-based ionic liquids to present slightly higher infinite dilution activity coefficients for non-polar solvents, becoming slightly lower for polar solvents, suggesting that the ammonium-based ionic liquids present somewhat higher polarities. In good agreement these compounds present lower toxicities than the phosphonium congeners. To explain this behavior quantum chemical gas phase DFT calculations were performed on isolated ion pairs at the BP-TZVP level of theory. Electronic density results were used to derive electrostatic potentials of the identified minimum conformers. Electrostatic potential-derived CHelpG and Natural Population Analysis charges show the P atom of the tetraalkylphosphonium-based ionic liquids cation to be more positively charged than the N atom in the tetraalkylammonium-based analogous IL cation, and a noticeable charge delocalization occurring in the tetraalkylammonium cation, when compared with the respective phosphonium congener. It is argued that this charge delocalization is responsible for the enhanced polarity observed on the ammonium based ionic liquids explaining the changes in the thermophysical properties observed.

  19. Low-level waste disposal in highly populated areas

    Energy Technology Data Exchange (ETDEWEB)

    Kowalski, E.; McCombie, C.; Issler, H. [NAGRA-Swiss National Cooperative for the Storage of Radioactive Waste, Baden (Switzerland)

    1989-11-01

    Nuclear-generated electricity supplies almost 40% of the demand in Switzerland (the rest being hydro-power). Allowing for a certain reserve and assuming an operational life-time of 40 years for each reactor, and taking into account wastes from decommissioning and from medicine, industry and research, the total amount of low-level radioactive waste to be disposed of is about 175,000 m{sup 3}. Since there are no unpopulated areas in Switzerland, and since Swiss Federal Law specifies that the safety of disposal may not depend upon supervision of the repository, no shallow-land burial has been foreseen, even for short-lived low-level waste. Instead, geological disposal in a mined cavern system with access through a horizontal tunnel was selected as the best way of meeting the requirements and ensuring the necessary public acceptance.

  20. Corrosion issues in high-level nuclear waste containers

    Science.gov (United States)

    Asl, Samin Sharifi

    In this dissertation different aspects of corrosion and electrochemistry of copper, candidate canister material in Scandinavian high-level nuclear waste disposal program, including the thermodynamics and kinetics of the reactions that are predicted to occur in the practical system have been studied. A comprehensive thermodynamic study of copper in contact with granitic groundwater of the type and composition that is expected in the Forsmark repository in Sweden has been performed. Our primary objective was to ascertain whether copper would exist in the thermodynamically immune state in the repository, in which case corrosion could not occur and the issue of corrosion in the assessment of the storage technology would be moot. In spite of the fact that metallic copper has been found to exist for geological times in granitic geological formations, copper is well-known to be activated from the immune state to corrode by specific species that may exist in the environment. The principal activator of copper is known to be sulfur in its various forms, including sulfide (H2S, HS-, S2-), polysulfide (H2Sx, HSx -, Sx 2-), poly sulfur thiosulfate ( SxO3 2-), and polythionates (SxO6 2-). A comprehensive study of this aspect of copper chemistry has never been reported, and yet an understanding of this issue is vital for assessing whether copper is a suitable material for fabricating canisters for the disposal of HLNW. Our study identifies and explores those species that activate copper; these species include sulfur-containing entities as well as other, non-sulfur species that may be present in the repository. The effects of temperature, solution pH, and hydrogen pressure on the kinetics of the hydrogen electrode reaction (HER) on copper in borate buffer solution have been studied by means of steady-state polarization measurements, including electrochemical impedance spectroscopy (EIS). In order to obtain electrokinetic parameters, such as the exchange current density and the

  1. Exploiting Aura OMI Level 2 Data with High Resolution Visualization

    Science.gov (United States)

    Wei, J. C.; Yang, W.; Johnson, J. E.; Zhao, P.; Gerasimov, I. V.; Pham, L.; Vicente, G. A.; Shen, S.

    2014-12-01

    Satellite data products are important for a wide variety of applications that can bring far-reaching benefits to the science community and the broader society. These benefits can best be achieved if the satellite data are well utilized and interpreted, such as model inputs from satellite, or extreme event (such as volcano eruption, dust storm, …etc) interpretation from satellite. Unfortunately, this is not always the case, despite the abundance and relative maturity of numerous satellite data products provided by NASA and other organizations. One way to help users better understand the satellite data is to provide data along with 'Images', including accurate pixel-level (Level 2) information, pixel coverage area delineation, and science team recommended quality screening for individual geophysical parameters. Goddard Earth Sciences Data and Information Services Center (GES DISC) always strives to best support (i.e., Software-as-a-service, SaaS) the user-community for NASA Earth Science Data. In this case, we will present a new visualization tool that helps users exploiting Aura Ozone Monitoring Instrument (OMI) Level 2 data. This new visualization service utilizes Open Geospatial Consortium (OGC) standard-compliant Web Mapping Service (WMS) and Web Coverage Service (WCS) calls in the backend infrastructure. The functionality of the service allows users to select data sources (e.g., multiple parameters under the same measurement, like NO2 and SO2 from OMI Level 2 or same parameter with different methods of aggregation, like NO2 in OMNO2G and OMNO2D products), defining area-of-interest and temporal extents, zooming, panning, overlaying, sliding, and data subsetting and reformatting. The interface will also be able to connect to other OGC WMS and WCS servers, which will greatly enhance its expandability to integrate additional outside data/map sources (such as Global Imagery Browse Services (GIBS)).

  2. Factors Affecting Noise Levels of High-Speed Handpieces

    Science.gov (United States)

    2012-06-01

    office communication and increase patient anxiety. Purpose: To determine if three noise-reducing techniques utilized in larger scale , non- dental...hearing loss may cause confusion, fear, and loneliness , and that sometimes hearing loss is accompanied by dizziness, which would be a handicap in the...employee noise exposures equal or exceed an 8- hour time-weighted average sound level (TWA) of 85 decibels measured on the A scale (slow response) or

  3. Regulation by ammonium of glutamate dehydrogenase (NADP+) from Saccharomyces cerevisiae.

    Science.gov (United States)

    Bogonez, E; Satrústegui, J; Machado, A

    1985-06-01

    The activity of glutamate dehydrogenase (NADP+) (EC 1.4.1.4; NADP-GDH) of Saccharomyces cerevisiae is decreased under conditions in which intracellular ammonia concentrations increases. A high internal ammonia concentration can be obtained (a) by increasing the ammonium sulphate concentration in the culture medium, and (b) by growing the yeast either in acetate + ammonia media, where the pH of the medium rises during growth, or in heavily buffered glucose + ammonia media at pH 7.5. Under these conditions cellular oxoglutarate concentrations do not vary and changes in NADP-GDH activity appear to provide a constant rate of oxoglutarate utilization. The following results suggest that the decrease in NADP-GDH activity in ammonia-accumulating yeast cells is brought about by repression of synthesis: (i) after a shift to high ammonium sulphate concentrations, the number of units of activity per cell decreased as the inverse of cell doubling; and (ii) the rate of degradation of labelled NADP-GDH was essentially the same in ammonia-accumulating yeast cells and in controls, whereas the synthesis constant was much lower in the ammonia-accumulating cells than in the controls.

  4. Correlation between High Density Lipoprotein Cholesterol (HDL) Level and Aerobic Activity Level.

    Science.gov (United States)

    1987-04-01

    over a 40 day period for HDtJICholesteroll and Total Choleis- added with the "reverse" technique, This technique is only poai- tarot . The results are...Stand- tarot and Total Cholestero levels, it is beat that eet laoatr ard and a control Serum were each analyzed 10 times giving the * determinle its

  5. Cultural education through the high school level English textbooks

    Directory of Open Access Journals (Sweden)

    Ookawa Kouki

    2015-09-01

    Full Text Available It cannot be denied that intercultural understanding is crucial in the process of learning English at elementary school, junior high school, high school, and beyond. This paper analyzes the high school English textbooks approved by the Ministry of Education, Culture, Sports, Science and Technology in Japan from the perspective of intercultural understanding. First, it elucidates the types of articles, the countries materials deal with, and the purposes of the materials used in the books. Then it considers important elements of intercultural education. The result of the research shows that the materials contain various kinds of categories, and many concern English-speaking countries. Furthermore, an important fact is that many materials concerning Japan, aimed at understanding its own culture, are shown in the textbooks as well. Finally, the paper suggests future direction for the use of materials in the textbooks in order to facilitate intercultural understanding.

  6. Chiral ammonium betaine-catalyzed asymmetric Mannich-type reaction of oxindoles

    Directory of Open Access Journals (Sweden)

    Masahiro Torii

    2016-09-01

    Full Text Available A highly diastereo- and enantioselective Mannich-type reaction of 3-aryloxindoles with N-Boc aldimines was achieved under the catalysis of axially chiral ammonium betaines. This catalytic method provides a new tool for the construction of consecutive quaternary and tertiary stereogenic carbon centers on biologically intriguing molecular frameworks with high fidelity.

  7. Towards a General Understanding of Carbonyl-Stabilised Ammonium Ylide-Mediated Epoxidation Reactions.

    Science.gov (United States)

    Novacek, Johanna; Roiser, Lukas; Zielke, Katharina; Robiette, Raphaël; Waser, Mario

    2016-08-01

    The key factors for carbonyl-stabilised ammonium ylide-mediated epoxidation reactions were systematically investigated by experimental and computational means and the hereby obtained energy profiles provide explanations for the observed experimental results. In addition, we were able to identify the first tertiary amine-based chiral auxiliary that allows for high enantioselectivities and high yields for such epoxidation reactions.

  8. A School News Bureau: PR Training at High School Level

    Science.gov (United States)

    Sullivan, Dolores P.

    1978-01-01

    Describes how a high school journalism teacher established a student news bureau to channel information about schools in the school system to the local media; lists advantages of the news bureau to its staff members and to the school system. (GW)

  9. Effectiveness of Ammonium-Nitrogen and Nitrate-Nitrogen in Irrigation Water in Paddy Rice without Topdressed Nitrogen at the Panicle Formation Stage

    OpenAIRE

    池田, 元輝; 渡辺, 孝賢; Ikeda, Motoki; Watanabe, Takayasu

    2002-01-01

    A pot experiment was conducted to evaluate the efficiency of ammonium- and nitrate- nitrogen contained in irrigation water during the reproductive growth period of paddy rice (Oryza sativa L. cv. Hinohikari) that did not receive topdressed nitrogen at the panicle formation stage. lrrigation of water containing a low level of nitrogen (7mgNL^-1) did not increase yields so much compared to topdressed nitrogen. lrrigation of water containing a high level of nitrogen (14mgNL^-1) caused substantia...

  10. Scientific Creativity and High Ability: Gender and academic level differences

    Directory of Open Access Journals (Sweden)

    Fernando Javier ESPARZA MOLINA

    2015-10-01

    Full Text Available  The purpose of this study was to investigate the influence of gender and educational level on scientific creativity among gifted/talented students. A cohort of creatividad científica y alta habilidad: diferencias de género y nivel educativo 78 secondary school students from 12 to 16 years old participated in this research. The scientific creativity was measured using the Creative Scientific Ability Test (Sak & Ayas, 2011 designed for secondary school students from 11 to 14 years old. Its theoretical framework sets up the measurement of a three dimensional structure: general creative abilities (fluency, flexibility and creativity, scientific creative abilities (hypothesis generation, hypothesis testing and evidence evaluation and scientific knowledge. This test has the right adequate psychometric properties with a Cronbach’s alpha coefficient of 0.848 (Sak & Ayas, 2013. Results indicated that male students scored significantly higher in a task named Interaction Graph which measures hypothesis generation in interdisciplinary science. The analysis also showed that students involved in upper education levels scores significantly higher in general fluency and in the task called The Food Chain which measures evidence evaluation in the area of ecology.

  11. Digitalizing historical high resolution water level data: Challenges and opportunities

    Science.gov (United States)

    Holinde, Lars; Hein, Hartmut; Barjenbruch, Ulrich

    2017-04-01

    Historical tide-gauge data offer the opportunities for determining variations in key characteristics for water level data and the analyses of past extreme events (storm surges). These information are important for calculating future trends and scenarios. But there are challenges involved due to the extensive effort needed to digitalize gauge sheets and quality control the resulting historical data. Based on these conditions, two main sources for inaccuracies in historical time series can be identified. First are several challenges due to the digitalization of the historical data, e.g. general quality of the sheets, multiple crossing lines of the observed water levels and additional comments on the sheet describing problems or additional information during the measurements. Second are problems during the measurements themselves. These can include the incorrect positioning of the sheets, trouble with the tide-gauge and maintenance. Errors resulting from these problems can be e.g. flat lines, discontinuities and outlier. Especially, the characterization of outliers has to be conducted carefully, to distinguish between real outliers and the appearance of extreme events. Methods for the quality control process involve the use of statistics, machine learning and neural networks. These will be described and applied to three different time series from tide gauge stations at the cost of Lower Saxony, Germany. Resulting difficulties and outcomes of the quality control process will be presented and explained. Furthermore, we will present a first glance at analyses for these time series.

  12. Spatial distribution and inhibition by ammonium of methane oxidation in intertidal freshwater marshes

    NARCIS (Netherlands)

    Van der Nat, F.J.; de Brouwer, J.F.C.; Middelburg, J.J.; Laanbroek, H.J.

    1997-01-01

    In two intertidal marshes, the vertical distribution in the sediment and inhibition by ammonium of methane oxidation were investigated by slurry incubation experiments. The two sites differ in their dominant vegetation type, i.e., reed and bulrush, and in their heights above sea level. The reed site

  13. High levels of melatonin generated during the brewing process.

    Science.gov (United States)

    Garcia-Moreno, H; Calvo, J R; Maldonado, M D

    2013-08-01

    Beer is a beverage consumed worldwide. It is produced from cereals (barley or wheat) and contains a wide array of bioactive phytochemicals and nutraceutical compounds. Specifically, high melatonin concentrations have been found in beer. Beers with high alcohol content are those that present the greatest concentrations of melatonin and vice versa. In this study, gel filtration chromatography and ELISA were combined for melatonin determination. We brewed beer to determine, for the first time, the beer production steps in which melatonin appears. We conclude that the barley, which is malted and ground in the early process, and the yeast, during the second fermentation, are the largest contributors to the enrichment of the beer with melatonin. © 2012 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  14. High Level Architecture (HLA) federation with Umbra and OPNET federates.

    Energy Technology Data Exchange (ETDEWEB)

    Oppel, Fred John III; Hart, Brian; Van Leeuwen, Brian P.

    2004-03-01

    Network-centric systems that depend on mobile wireless ad hoc networks for their information exchange require detailed analysis to support their development. In many cases, this critical analysis is best provided with high-fidelity system simulations that include the effects of network architectures and protocols. In this research, we developed a high-fidelity system simulation capability using an HLA federation. The HLA federation, consisting of the Umbra system simulator and OPNET Modeler network simulator, provides a means for the system simulator to both affect, and be affected by, events in the network simulator. Advances are also made in increasing the fidelity of the wireless communication channel and reducing simulation run-time with a dead reckoning capability. A simulation experiment is included to demonstrate the developed modeling and simulation capability.

  15. High-Speed, Low-Level Flight: Aircrew Factors

    Science.gov (United States)

    1980-03-01

    informations tate haute ou tate basse montgs sur lea tableau de bord , 20/ sur lea dispositifs de prasentation des informations par dispositifs montds sur casque...En ca qui concerne lea dispositifs mont~s sur le tableau de bord et la charge de travail des iquipages, Monsieur MORRIS A. OSTGAARD a pr4sent6 de...need for an inertial naviga- tion system, freeing the pilot from the current high task-loading requirements of navigational pilotage . DISCUFSION It

  16. Radiation resistance of copper alloys at high exposure levels

    Energy Technology Data Exchange (ETDEWEB)

    Garner, F.A. (Pacific Northwest Lab., Richland, WA (USA)); Zinkle, S.J. (Oak Ridge National Lab., TN (USA))

    1990-08-01

    Copper alloys are currently being considered for high heat flux applications in fusion power devices. A review is presented of the results of two separate series of experiments on the radiation response of copper and copper alloys. One of these involved pure copper and boron-doped copper in the ORR mixed spectrum reactor. The other series included pure copper and a wide array of copper alloys irradiated in the FFTF fast reactor 16 refs., 13 figs.

  17. High Voltage Breakdown Levels in Various EPC Potting Materials

    Science.gov (United States)

    Komm, David S.

    2006-01-01

    This viewgraph presentation reviews exploration activities at JPL into various potting materials. Since high power space-borne microwave transmitters invariably use a vacuum tube as a final power amplifier, and this tube requires high electrode voltages for operation. The associated high voltage insulation typically represents a significant fraction of the mass of the transmitter. Since mass is always a premium resource on board spacecraft, we have been investigating materials with the potential to reduce the mass required for our applications here at JPL. This paper describes electrical breakdown results obtained with various potting materials. Conathane EN-11 (polyurethane) is the traditional HVPS encapsulant at JPL, but due to temperature limitations and durability issues it was deemed inappropriate for the particular application (i.e., CloudSat radar). The choices for the best available materials were epoxies, or silicones. Epoxies are too rigid, and were deemed inadvisable. Two silicones were further investigated (i.e.,ASTM E595- 93e2: GE RTV566(R) and Dow Corning 93-500X(R), another compound was considered (i.e., DC material, Sylgard 184(R)). "Loading" (adding filler materials) the potting compound will frequently alter the final material properties. Powdered alumina and borosilicate glass known as "microballoons" were investigated as possible loading materials. The testing of the materials is described. Each of the two loading materials offers advantages and disadvantages. The advantages and disadvantages are described.

  18. Accurate Measurement of the in vivo Ammonium Concentration in Saccharomyces cerevisiae

    Directory of Open Access Journals (Sweden)

    Hugo F. Cueto-Rojas

    2016-04-01

    Full Text Available Ammonium (NH4+ is the most common N-source for yeast fermentations, and N-limitation is frequently applied to reduce growth and increase product yields. While there is significant molecular knowledge on NH4+ transport and assimilation, there have been few attempts to measure the in vivo concentration of this metabolite. In this article, we present a sensitive and accurate analytical method to quantify the in vivo intracellular ammonium concentration in Saccharomyces cerevisiae based on standard rapid sampling and metabolomics techniques. The method validation experiments required the development of a proper sample processing protocol to minimize ammonium production/consumption during biomass extraction by assessing the impact of amino acid degradation—an element that is often overlooked. The resulting cold chloroform metabolite extraction method, together with quantification using ultra high performance liquid chromatography-isotope dilution mass spectrometry (UHPLC-IDMS, was not only more sensitive than most of the existing methods but also more accurate than methods that use electrodes, enzymatic reactions, or boiling water or boiling ethanol biomass extraction because it minimized ammonium consumption/production during sampling processing and interference from other metabolites in the quantification of intracellular ammonium. Finally, our validation experiments showed that other metabolites such as pyruvate or 2-oxoglutarate (αKG need to be extracted with cold chloroform to avoid measurements being biased by the degradation of other metabolites (e.g., amino acids.

  19. Accurate Measurement of the in vivo Ammonium Concentration in Saccharomyces cerevisiae.

    Science.gov (United States)

    Cueto-Rojas, Hugo F; Maleki Seifar, Reza; Ten Pierick, Angela; Heijnen, Sef J; Wahl, Aljoscha

    2016-04-23

    Ammonium (NH₄⁺) is the most common N-source for yeast fermentations, and N-limitation is frequently applied to reduce growth and increase product yields. While there is significant molecular knowledge on NH₄⁺ transport and assimilation, there have been few attempts to measure the in vivo concentration of this metabolite. In this article, we present a sensitive and accurate analytical method to quantify the in vivo intracellular ammonium concentration in Saccharomyces cerevisiae based on standard rapid sampling and metabolomics techniques. The method validation experiments required the development of a proper sample processing protocol to minimize ammonium production/consumption during biomass extraction by assessing the impact of amino acid degradation-an element that is often overlooked. The resulting cold chloroform metabolite extraction method, together with quantification using ultra high performance liquid chromatography-isotope dilution mass spectrometry (UHPLC-IDMS), was not only more sensitive than most of the existing methods but also more accurate than methods that use electrodes, enzymatic reactions, or boiling water or boiling ethanol biomass extraction because it minimized ammonium consumption/production during sampling processing and interference from other metabolites in the quantification of intracellular ammonium. Finally, our validation experiments showed that other metabolites such as pyruvate or 2-oxoglutarate (αKG) need to be extracted with cold chloroform to avoid measurements being biased by the degradation of other metabolites (e.g., amino acids).

  20. Characteristics of simultaneous ammonium and phosphate adsorption from hydrolysis urine onto natural loess.

    Science.gov (United States)

    Jiang, Shanqing; Wang, Xiaochang; Yang, Shengjiong; Shi, Honglei

    2016-02-01

    Nutrient recovery from human urine is a promising pretreatment of domestic wastewater and provides a sustainable recyclability of N and P. In this study, batch experiments were conducted to identify the characteristics of natural loess (NL) for the adsorption and recovery of ammonium and phosphate from hydrolysis urine (HU). The adsorption mechanisms, the adsorption kinetics and isotherms, as well as the major influencing factors, such as pH and temperature, were investigated. Results revealed that adsorption of ammonium occurred by means of ion exchange and molecule adsorption with the ≡ Si-OH groups, while phosphate adsorption was based on the calcium phosphate precipitation reaction and formation of inner-sphere complexes with ≡ M-OH groups. The adsorption processes of ammonium and phosphate were well described by the pseudo-second-order kinetic model and the Freundlich isotherm model. Adsorption of phosphate was endothermic, while ammonium adsorption was exothermic. Furthermore, the maximum ammonium and phosphate adsorption capacities of NL was 23.24 mg N g(-1) and 4.01 mg P g(-1) at an initial pH of 9 and 10, respectively. Results demonstrated that nutrient-adsorbed NL used as compound fertilizer or conventional fertilizer superaddition was feasible for its high contents of N and P as well as its environmental friendliness.