WorldWideScience

Sample records for hg vapour diffusion

  1. Thermodynamic properties of the liquid Hg-Tl alloys determined from vapour pressure measurements

    Directory of Open Access Journals (Sweden)

    Gierlotka W.

    2002-01-01

    Full Text Available The partial vapour pressure of mercury over liquid Hg-Tl liquid solutions were determined in the temperature range from 450 to 700 K by direct vapour pressure measurements carried out with the quartz gauge. From the measured ln pHg vs. T relationships activities of mercury were determined. Using Redlich-Kister formulas logarithms of the activity coefficients were described with the following equations: From which all thermodynamic functions in the solutions can be derived.

  2. Thermal radiation and low-temperature-vapour growth of HgI 2 crystal in production furnace

    Science.gov (United States)

    Roux, A.; Fedoseyev, A.; Roux, B.

    1993-06-01

    Heat exchanges in a sealed ampoule in the LTVG (low temperature vapour growth) furnace have been modelled in order to compute temperature fields and control the growth of HgI 2 crystals from vapour phase at low temperatures. We use a coupled conductive-radiative model to determine the shapes of the source and the crystal at different equilibrium states (i.e. without growth rate). The model involves conductivity anisotropy in the crystal and radiative exchanges between grey and diffuse surfaces (source and crystal interfaces, Pyrex walls), which are considered as opaque. Internal buoyancy effect is not taken into account as the pressure inside the ampoule is very small. The source temperature is fixed. For different undercoolings, i.e. for different cold finger temperatures, the "equilibrium" isotherm between the source/gas and crystal/gas interface has been numerically obtained. This "equilibrium" isotherm, which is associated with the stop of the growing process, gives a crystal shape. This shape is compared with experimental results given by the ETH-Zürich group. The model would permit a better understanding and control of the future HgI 2 crystal growth experiment. The computations are performed using a finite element package (FIDAP).

  3. Growth and characterization of Hg1–CdTe epitaxial films by isothermal vapour phase epitaxy (ISOVPE)

    Indian Academy of Sciences (India)

    Manju Malhotra; Madhukar Gautam; J K Radhakrishnan; Vinod Kapoor; Sudeep Verma; Upendra Kumar; Anand Kumar; Garima Gupta; Anshu Goyal; S Sitharaman

    2005-04-01

    Growth of Hg1–CdTe epitaxial films by a new technique called asymmetric vapour phase epitaxy (ASVPE) has been carried out on CdTe and CZT substrates. The critical problems faced in normal vapour phase epitaxy technique like poor surface morphology, composition gradient and dislocation multiplication have been successfully solved. The epitaxial films have been electrically characterized by using the Hall effect and capacitance–voltage (–) measurements.

  4. Influence of water and water vapour on the characteristics of KI treated HgI 2 detectors

    Science.gov (United States)

    Ponpon, J. P.; Amann, M.; Sieskind, M.

    After being cleaned using a potassium iodide solution in water followed by a water rinse, the surface of mercuric iodide is covered by a chemical complex identified as being KHgI 3·H 2O. This compound can adsorb large quantities of water and its electrical properties are strongly sensitive to water and water vapour. The consequences on the manufacturing and storing conditions (especially the relative humidity), of mercuric iodide-based devices are therefore of great concern. They are illustrated by the study of the electrical and spectrometric properties of HgI 2 nuclear radiation detectors.

  5. Moisture in Self-levelling Flooring Compounds. Part I. Water Vapour Diffusion Coefficients

    OpenAIRE

    Anderberg, Anders; Wadsö, Lars

    2004-01-01

    Diffusion coefficients of three self-levelling flooring compounds (SLC) and water vapour resistance of a primer have been measured with the cup method. The results show that the diffusion coefficient is dependent not only on the vapour content (relative humidity), but also on the absolute moisture content, i.e., there is a hysteresis effect on moisture transport. At RH lower than approximately 90 %, SLC have higher diffusion coefficients than a standard concrete (w/c 0.7 OPC), but the opposit...

  6. Binding of Vapour-Phase Mercury (Hg0) on Chemically Treated Bauxite Residues (Red Mud)

    Science.gov (United States)

    In this study, Hg capture using red mud, seawater-neutralized red mud, and acid-treated red mud is evaluated and compared to other, more conventional sorbent materials. Red mud (also known as bauxite residue) is a by-product of extracting alumina from ground bauxite ore by treati...

  7. Binding of Vapour-Phase Mercury (Hg0) on Chemically Treated Bauxite Residues (Red Mud)

    Science.gov (United States)

    In this study, Hg capture using red mud, seawater-neutralized red mud, and acid-treated red mud is evaluated and compared to other, more conventional sorbent materials. Red mud (also known as bauxite residue) is a by-product of extracting alumina from ground bauxite ore by treati...

  8. Doping and Diffusion in HgCdTe

    Science.gov (United States)

    1991-01-28

    In’i, -InT. Te - 1.8 ( - 3 .5 )h ( + 2.9 - 6/) TeT1’- Tej . 4 Hg rich HgCdTe Hg - 1.8 + 1.2 + 1.4 - 2p H - ’g, - H g j.. ’TI - tetrahedral position...A. Anderson, Appl. Phys. Lett. 53, 11.81 (1988). B. D. Patterson, Rev. Mod. Phys. 60, 69 (1988). 60 V. A. Singh , C. Weigel, J. W. Corbett, and L. M

  9. Stability and diffusion of Hg implanted YBa$_{2}$Cu$_{3}$O$_{6+x}$

    CERN Document Server

    Araújo, J P; Wahl, U; Marques, J G; Alves, E; Amaral, V S; Lourenço, A A; Galindo, V; Von Papen, T; Senateur, J P; Weiss, F; Vantomme, A; Langouche, G; Melo, A A; Da Silva, M F A; Soares, J C; Sousa, J B

    1999-01-01

    The radioactive isotope $^{197m}$Hg was implanted at 60 keV with low fluences (10$^{13}$ ions/cm$^{2}$ ) into YBa$_{2}$Cu$_{3}$O$_{6+x}$ (YBCO) superconducting thin films at ISOLDE/CERN. We report on the Hg dynamics and stability inside the YBCO lattice as a function of annealing temperature up to 890 K in vacuum or O$_{2}$ atmosphere. The perturbed angular correlation (PAC) technique was used for probing the Hg behavior at the atomic scale, while by monitoring the sample's activity in situ the Hg outdiffusion was studied. We found that Hg ions occupy unique lattice sites and that Hg should be bound to two apical oxygens. Hg diffusion occurs only for annealing temperatures above 653 K, in vacuum. The Hg migration energy was estimated to be EM = 1.58 $\\pm$ 0.15 eV.

  10. Formation of calcium phosphates by vapour diffusion in highly concentrated ionic micro-droplets

    Energy Technology Data Exchange (ETDEWEB)

    Iafisco, M. [Alma Mater Studiorum Universita di Bologna, Dipartimento di Chimica ' ' G. Ciamician' ' , Via Selmi 2, 40126 Bologna (Italy); Universita del Piemonte Orientale, Dipartimento di Scienze Mediche, Via Solaroli 4, 28100 Novara (Italy); Delgado-Lopez, J.M.; Gomez-Morales, J.; Hernandez-Hernandez, M.A.; Rodriguez-Ruiz, I. [Laboratorio de Estudios Cristalograficos, IACT CSIC-UGR, Edificio Lopez Neyra, Avenida del Conocimiento, s/n 18100 Armilla (Spain); Roveri, N. [Alma Mater Studiorum Universita di Bologna, Dipartimento di Chimica ' ' G. Ciamician' ' , Via Selmi 2, 40126 Bologna (Italy)

    2011-08-15

    In this work we have used the sitting drop vapour diffusion technique, employing the ''crystallization mushroom '' to analyze the evolution of calcium phosphate crystallization in micro-droplets containing high initial concentrations of Ca{sup 2+} and HPO{sub 4}{sup 2-}. The decomposition of NH{sub 4}HCO{sub 3} solution produces vapours of NH{sub 3} and CO{sub 2} which diffuse through the droplets containing an aqueous solution of Ca(CH{sub 3}COO){sub 2} and (NH{sub 4}){sub 2}HPO{sub 4}. The result is the increase of pH by means of the diffusion of NH{sub 3} gas and the doping of the calcium phosphate with CO{sub 3}{sup 2-} ions by means of the diffusion of CO{sub 2} gas. The pH of the crystallization process is monitored and the precipitates at different times are characterized by XRD, FTIR, TGA, SEM and TEM techniques. The slow increase of pH and the high concentration of Ca{sup 2+} and HPO{sub 4}{sup 2-} in the droplets induce the crystallization of three calcium phosphate phases: dicalcium phosphate dihydrate (DCPD, brushite), octacalcium phosphate (OCP) and carbonate-hydroxyapatite (HA). The amount of HA nanocrystals with needle-like morphology and dimensions of about 100 nm, closely resembling the inorganic phase of bones, gradually increases, with the precipitation time up to 7 days, whereas the amount of DCPD, growing along the b axis, increases up to 3 days. Then, DCDP crystals start to hydrolyze yielding OCP nanoribbons and HA nanocrystals. (copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  11. Diffusion Mechanism for Arsenic in Intrinsic and Extrinsic Conditions in HgCdTe

    Science.gov (United States)

    Grenouilloux, T.; Ferron, A.; Péré-Laperne, N.; Mathiot, D.

    2017-09-01

    Due to its low diffusivity and high activation rate, arsenic has become the dopant of choice in p/n HgCdTe high operating temperature technology. Its diffusion mechanism, however, remains imprecise. In this work, arsenic diffusion was studied in molecular beam epitaxy HgCdTe structures consisting of alternatively As-doped and intrinsic layers grown on a CdZnTe substrate. The diffusion coefficient of As was extracted from secondary ion mass spectroscopy concentration profiles. Annealings were performed for different temperatures, mercury partial pressures ( P Hg), annealing times and cadmium atomic fractions. Fermi-level effect on diffusion was observed, indicating extrinsic conditions for diffusion at high As concentration. Based on the variation of As diffusivity with P Hg and As concentration, we propose that As diffusion occurs on both II and VI sublattices. Our results are consistent with the fact that AsVI diffusion is assisted by the Te interstitial, introducing donor levels in the bandgap, while AsII diffusion is assisted by the cation vacancy.

  12. High performance liquid chromatography coupled to atomic fluorescence spectrometry for the speciation of the hydride and chemical vapour-forming elements As, Se, Sb and Hg: A critical review

    Energy Technology Data Exchange (ETDEWEB)

    Chen Yuwei [Department of Chemistry and Biochemistry, Laurentian University, Ramsey Lake Road, Sudbury P3E 2C6 (Canada); Belzile, Nelson, E-mail: nbelzile@laurentian.ca [Department of Chemistry and Biochemistry, Laurentian University, Ramsey Lake Road, Sudbury P3E 2C6 (Canada); Cooperative Freshwater Ecology Unit, Laurentian University, Ramsey Lake Road, Sudbury P3E 2C6 (Canada)

    2010-06-25

    We present the most recent applications of high performance liquid chromatography (HPLC) hyphenated to hydride generation or chemical vapour generation and atomic fluorescence spectrometry (HG/CVG-AFS), for the determination and speciation of the selected hydride-forming elements arsenic (As), selenium (Se) and antimony (Sb) and the chemical vapour-forming metal Hg. The review focuses on sample preparation, post-column treatments and on the applications of this technique to various liquid and solid samples. This review also intends to discuss some limitations associated to HPLC-HG/CVG-AFS due to the necessity on post-column treatments, including the oxidation of organo-element compounds and the pre-reduction to a suitable valence. Nevertheless, the hyphenated technique HPLC-HG/CVG-AFS remains an efficient, sensitive and affordable approach to perform speciation of the four studied elements as shown by the variety of applications presented and discussed in this review.

  13. Colloidal mercury (Hg) distribution in soil samples by sedimentation field-flow fractionation coupled to mercury cold vapour generation atomic absorption spectroscopy.

    Science.gov (United States)

    Santoro, A; Terzano, R; Medici, L; Beciani, M; Pagnoni, A; Blo, G

    2012-01-01

    Diverse analytical techniques are available to determine the particle size distribution of potentially toxic elements in matrices of environmental interest such as soil, sediments, freshwater and groundwater. However, a single technique is often not exhaustive enough to determine both particle size distribution and element concentration. In the present work, the investigation of mercury in soil samples collected from a polluted industrial site was performed by using a new analytical approach which makes use of sedimentation field-flow fractionation (SdFFF) coupled to cold vapour generation electrothermal atomic absorption spectroscopy (CV-ETAAS). The Hg concentration in the SdFFF fractions revealed a broad distribution from about 0.1 to 1 μm, roughly following the particle size distributions, presenting a maximum at about 400-700 nm in diameter. A correlation between the concentration of Hg in the colloidal fraction and organic matter (O.M.) content in the soil samples was also found. However, this correlation is less likely to be related to Hg sorption to soil O.M. but rather to the presence of colloidal mercuric sulfide particles whose size is probably controlled by the occurrence of dissolved O.M. The presence of O.M. could have prevented the aggregation of smaller particles, leading to an accumulation of mercuric sulfides in the colloidal fraction. In this respect, particle size distribution of soil samples can help to understand the role played by colloidal particles in mobilising mercury (also as insoluble compounds) and provide a significant contribution in determining the environmental impact of this toxic element.

  14. Viscosity, Thermal Conductivity and Thermal Diffusion Ratio of the Alkali Metal Vapours.

    OpenAIRE

    Fialho, Paulo; Ramires, Maria de Lurdes V.; João M. N. A. Fareleira; Nieto de Castro, Carlos A.

    1994-01-01

    Copyright © 1994 by Technomic Publishing Company, Inc. Proceedings of the Twenty-Second International Conference on Thermal Condutivity. Tempe, Arizona, November 7-10, 1993. The Subcommittee of Transport Properties of IUP AC started in 1982 a project with the objective of correlating and predicting the transport properties of the alkali metal vapours, in the temperature and pressure zones that are useful to the scientific and industrial uses. In a recent paper [1] the authors suggested ...

  15. Thermal diffusion of water vapour in porous materials: fact or fiction?

    DEFF Research Database (Denmark)

    Janssen, Hans

    2011-01-01

    of all measurements allows concluding that no consistent nor significant thermal diffusion can be observed. This brings these investigations in line with their earlier opponents. This conclusion also agrees with thermodynamics, which confirms the actual existence of thermal diffusion, but also indicates...

  16. InAs pixel matrix detectors fabricated by diffusion of Zn in a metal-organic vapour-phase epitaxy reactor

    Energy Technology Data Exchange (ETDEWEB)

    Saeynaetjoki, A. [Optoelectronics Laboratory, Helsinki University of Technology, P.O. Box 3500, 02015 HUT (Finland)]. E-mail: antti.saynatjoki@tkk.fi; Kostamo, P. [Optoelectronics Laboratory, Helsinki University of Technology, P.O. Box 3500, 02015 HUT (Finland); Sormunen, J. [Optoelectronics Laboratory, Helsinki University of Technology, P.O. Box 3500, 02015 HUT (Finland); Riikonen, J. [Optoelectronics Laboratory, Helsinki University of Technology, P.O. Box 3500, 02015 HUT (Finland); Lankinen, A. [Optoelectronics Laboratory, Helsinki University of Technology, P.O. Box 3500, 02015 HUT (Finland); Lipsanen, H. [Optoelectronics Laboratory, Helsinki University of Technology, P.O. Box 3500, 02015 HUT (Finland); Andersson, H. [Oxford Instruments Analytical Oy (United Kingdom); Banzuzi, K. [Oxford Instruments Analytical Oy (United Kingdom); Nenonen, S. [Oxford Instruments Analytical Oy (United Kingdom); Sipilae, H. [Oxford Instruments Analytical Oy (United Kingdom); Vaijaervi, S. [Oxford Instruments Analytical Oy (United Kingdom); Lumb, D. [Science Payload and Advanced Concepts Office, ESA/ESTEC, Nordwijk (Netherlands)

    2006-07-01

    We introduce a zinc diffusion process to fabricate an InAs-based detector matrix using an atmospheric pressure metal-organic vapour-phase epitaxy reactor. Current-voltage characteristics are measured and different diffusion parameters are experimented. Spectral alpha radiation response of the diode is reported. To our knowledge, this is the first time that InAs was used as an alpha particle detector.

  17. Vapour pressure of components made by the presence of HgS(s,alpha) in an oil/gas reservoir and consequences for the produced gas

    Energy Technology Data Exchange (ETDEWEB)

    Oestvold, T.; Gustavsen, Oe.; Grande, K.; Aas, N.; Olsvik, Mimmi Kjetsaa

    2006-03-15

    A thermodynamic analysis is presented on how components made from HgS (s,alpha), existing in a oil/gas reservoir, will distribute themselves between gas, water, liquid and solid components as a function of temperature and pressure. The consequence of the formation of mercury containing components on gas injection and on gas quality is discussed. Since equilibrium is established in the model calculation, other gas components in the gas phase and components in condensed phases present will also influence the composition of the gas. Six cases are considered in the calculation: 1) HgS(s,alpha) - Ar(g), 2) HgS(s,alpha) - Ar (g) - water with 10-4 molal NaCl at pH = 7, 3) HgS(s,alpha) - CH{sub 4}(g), 4) HgS(s,alpha) - CH{sub 4} (g) - water with 10-4 molal NaCl at pH = 7 and 5) HgS(s,alpha) - natural gas - water with 10-4 molal NaCl at pH = 7, 6) HgS(s,alpha) - natural gas - water with 10-4 molal NaCl and 5*10-5 molal NO-3- at pH = 7. When HgS(s,alpha) is present in an oil reservoir at 170 deg C and 200 bar, these calculations show that the major components formed are: H{sub 2}(g), H{sub 2}S(g), Hg(l) and Hg(g) together with carbon. Mercury in the gas phase in the cases 1) is 4*10-7 bar and is determined by the evaporation and decomposition HgS(g) in the reservoir. In case 2) P{sub Hg} = 5.7*10-4 bar mainly determined by the formation of sulphate in the water phase. In the cases 3), 4) and 5) these calculations show that the major components formed are: H{sub 2}(g), H{sub 2}S(g), Hg(l) and Hg(g) together with carbon, and the gas phase is dominated by Hg(g) at approx. *10-3 bar. The water phase may contain Hg(CH{sub 3}NH{sub 2}){sub 2}2+ if NO{sub 3}- for some reasons is introduced into the formation water, and the very carcinogenic dimethyl mercury compound, C{sub 2}HgH{sub 6}, can be formed in the gas phase. Both compounds, however, in insignificant low concentration/partial pressure. (Author)

  18. Numerical modeling of HgCdTe solidification: effects of phase diagram double-diffusion convection and microgravity level

    Science.gov (United States)

    Bune, Andris V.; Gillies, Donald C.; Lehoczky, Sandor L.

    1997-07-01

    A numerical model of HgCdTe solidification was implemented using finite the element code FIDAP. Model verification was done using both experimental data and numerical test problems. The model was used to eluate possible effects of double- diffusion convection in molten material, and microgravity level on concentration distribution in the solidified HgCdTe. Particular attention was paid to incorporation of HgCdTe phase diagram. It was found, that below a critical microgravity amplitude, the maximum convective velocity in the melt appears virtually independent on the microgravity vector orientation. Good agreement between predicted interface shape and an interface obtained experimentally by quenching was achieved. The results of numerical modeling are presented in the form of video film.

  19. PERFORMANCE OF A NEW DIFFUSIVE SAMPLER FOR HG0 DETERMINATION IN THE TROPOSPHERE

    Science.gov (United States)

    Mercury behaves uniquely in the atmosphere due to its volatility and long lifetime. The existing methods for measuring atmospheric mercury are either expensive or labour intensive. The present paper presents a new measurement technique, the diffusive sampler, that is portable, in...

  20. The impact of the surface on step-bunching and diffusion of Ga on GaAs (001) in metal-organic vapour phase epitaxy

    Science.gov (United States)

    Pristovsek, Markus; Poser, Florian; Richter, Wolfgang

    2016-07-01

    We studied diffusion by measuring step-bunching, island spacing, and the transition from step-flow growth to two-dimensional island growth of (001) GaAs in metal-organic vapour phase epitaxy and correlated them with the surface reconstruction measured by reflectance anisotropy spectroscopy. The V/III ratio had a small effect, while the square root of the growth rate was anti-proportional to the diffusion length. The thermal activation energy was about 2.3 eV on {{c}}(4× 4) terraces and 1.6 eV on (2× 4) domains at higher temperatures. Pronounced step-bunching coincided with large (4× 2) domains at the step-edges, causing smoother steps for the [11̅0] misorientation. This Ga-rich reconstruction at the step-edges is needed for the Schwoebel barrier to induce step-bunching. At higher temperatures of (2× 4) domains grow in size, the Schwoebel barrier reduces and nucleation becomes easier on this surface which reduces diffusion length and thus step-bunching.

  1. Determination of charge-carrier diffusion length in the photosensing layer of HgCdTe n-on-p photovoltaic infrared focal plane array detectors

    Energy Technology Data Exchange (ETDEWEB)

    Vishnyakov, A. V.; Stuchinsky, V. A., E-mail: stuchin@isp.nsc.ru; Brunev, D. V.; Zverev, A. V.; Dvoretsky, S. A. [Institute of Semiconductor Physics, Russian Academy of Science, Siberian Division, 13, Acad. Lavrent' ev Avenue, Novosibirsk 630090 (Russian Federation)

    2014-03-03

    In the present paper, we propose a method for evaluating the bulk diffusion length of minority charge carriers in the photosensing layer of photovoltaic focal plane array (FPA) photodetectors. The method is based on scanning a strip-shaped illumination spot with one of the detector diodes at a low level of photocurrents j{sub ph} being registered; such scanning provides data for subsequent analysis of measured spot-scan profiles within a simple diffusion model. The asymptotic behavior of the effective (at j{sub ph} ≠ 0) charge-carrier diffusion length l{sub d} {sub eff} as a function of j{sub ph} for j{sub ph} → 0 inferred from our experimental data proved to be consistent with the behavior of l{sub d} {sub eff} vs j{sub ph} as predicted by the model, while the obtained values of the bulk diffusion length of minority carriers (electrons) in the p-HgCdTe film of investigated HgCdTe n-on-p FPA photodetectors were found to be in a good agreement with the previously reported carrier diffusion-length values for HgCdTe.

  2. Effects of Gravity on the Double-Diffusive Convection during Directional Solidification of a Non-Dilute Alloy with Application to the HgCdTe

    Science.gov (United States)

    Bune, Andris; Gillies, Donald; Lehoczky, Sandor

    1999-01-01

    General 2-D and 3-D finite element model of non-dilute alloy solidification was used to simulate growth of HgCdTe in terrestrial and microgravity conditions. Parametric research was undertaken to investigate effects of gravity level, gravity vector orientation and growth velocity on the pattern of melt convection, shape of crystal/melt interface and radial thermal gradient. Verification of the model was undertaken by comparison with previously published results. For low growth velocities plane front solidification occurs. The location and the shape of the interface was determined using melting temperatures obtained from the HgCdTe liquidus curve. The low thermal conductivity of the solid HgCdTe causes thermal short circuit through the ampoule walls, resulting in curved isotherms in the vicinity of the interface. Double-diffusive convection in the melt is caused by radial temperature gradients and by material density inversion with temperature. Cooling from below and the rejection at the solid-melt interface of the heavier HgTe-rich solute each tend to reduce convection. Because of these complicating factors dimensional rather then non-dimensional modeling was performed. For gravity levels higher then 10(exp -7) of terrestrial one it was found that the maximum convection velocity is extremely sensitive to gravity vector orientation and can be reduced at least by 50% by choosing proper orientation of the ampoule. The predicted interface shape is in agreement with one obtained experimentally by quenching.

  3. Effects of Gravity on the Double-Diffusive Convection During Directional Solidification of a Non-Dilute Alloy with Application to HgCdTe

    Science.gov (United States)

    Bune, Andris V.; Gillies, Donald C.; Lehoczky, Sandor L.

    1999-01-01

    A general 2-D and 3-D finite element model of non-dilute alloy solidification was used to simulate growth of HgCdTe in terrestrial and microgravity conditions. Verification of the 3-D model was undertaken by comparison with previously published results on convection in an inclined cylinder. For low growth velocities, plane front solidification occurs. The location and the shape of the interface were determined using melting temperatures obtained from the HgCdTe liquidus curve. The low thermal conductivity of the solid HgCdTe causes a thermal short circuit through the ampoule walls, resulting in curved isotherms in the vicinity of the interface. Double-diffusive convection in the melt is caused by radial temperature gradients and by material density inversion due to the combined effects of composition and temperature. Cooling from below and the rejection at the solid-melt interface of the heavier HgTe-rich solute each tend to reduce convection. Because of these complicating factors, dimensional rather than non-dimensional modeling was performed. the predicted interface shape is in agreement with one obtained experimentally by quenching.

  4. Toxic metal dispersion in mining areas: from point source to diffusion pollution. The case of the Mt. Amiata Hg mining district (Southern Tuscany - Italy): new results.

    Science.gov (United States)

    Colica, Antonella; Chiarantini, Laura; Rimondi, Valentina; Benvenuti, Marco; Costagliola, Pilario; Lattanzi, Pierfranco; Paolieri, Mario; Rinaldi, Massimo

    2016-04-01

    Rivers draining mining areas may contribute to the diffusion of contaminants through their dispersion and accumulation into different morphological river units. The Paglia River's catchment (southern Tuscany) hosts the SE portion of the Mt. Amiata mercury district, the third most important worldwide (exploited from 1880 to 1980 with a total production of 100,000 tonnes Hg) before becoming a tributary of the Tiber River, which directly flows into Mediterranean Sea. The goals of this study are: 1) to recognize and distinguish different morphological units along the Paglia River watercourse, 2) to determine spatial/temporal distribution and concentration of Hg (and other toxic elements, particularly As) in different units. The analysis of morphological units was made by mapping their evolution from the beginning of mining activity (1883) to present day along 43 km of the Paglia watercourse defining eleven morphological sections across this river, and one across one of its tributaries, the Siele Creek, which drains various Hg mines located upstream. Four fundamental morphological/sedimentary unit types have been distinguished: stream sediments, bar, floodplain, and terraces. The latter occur in various orders and age: Pleistocenic, pre-mining (i.e., dating before 1880), and coeval to the mining activity. A total of 100 samples were taken from the various units in the selected transects, georeferenced and then analyzed for their Hg and As contents by ICP-OES. Arsenic contents generally never exceed 10 mg/kg. The observed ranges are: stream sediments 4.1÷8.2 mg/kg; bars 4.1÷6.6 mg/kg; floodplains 3.8÷6.6 mg/kg; terrace coeval with mining activity 3.2÷10.1 mg/kg. Hg contents in present-day stream sediments and bars are extremely variable (0.2÷27.5 and 1.4÷22.4 mg/kg respectively), and show a sharp increase at the confluence with Siele Creek. Floodplain sediments may reach up to 98 mg/kg. Terraces coeval with mining activity also show variable Hg contents (0.1÷66

  5. The Liquid Vapour Interface

    DEFF Research Database (Denmark)

    Als-Nielsen, Jens Aage

    1985-01-01

    In this short review we are concerned with the density variation across the liquid-vapour interface, i.e. from the bulk density of the liquid to the essentially zero density of the vapour phase. This density variation can in principle be determined from the deviation of the reflectivity from...

  6. A conservative vapour intrusion screening model of oxygen-limited hydrocarbon vapour biodegradation accounting for building footprint size

    Science.gov (United States)

    Knight, John H.; Davis, Gregory B.

    2013-12-01

    Petroleum hydrocarbon vapours pose a reduced risk to indoor air due to biodegradation processes where oxygen is available in the subsurface or below built structures. However, no previous assessment has been available to show the effects of a building footprint (slab size) on oxygen-limited hydrocarbon vapour biodegradation and the potential for oxygen to be present beneath the entire sub-slab region of a building. Here we provide a new, conservative and conceptually simple vapour screening model which links oxygen and hydrocarbon vapour transport and biodegradation in the vicinity and beneath an impervious slab. This defines when vapour risk is insignificant, or conversely when there is potential for vapour to contact the sub-slab of a building. The solution involves complex mathematics to determine the position of an unknown boundary interface between oxygen diffusing in from the ground surface and vapours diffusing upwards from a subsurface vapour source, but the mathematics reduces to a simple relationship between the vapour source concentration and the ratio of the half slab width and depth to the vapour source. Data from known field investigations are shown to be consistent with the model predictions. Examples of 'acceptable' slab sizes for vapour source depths and strengths are given. The predictions are conservative as an estimator of when petroleum hydrocarbon vapours might come in contact with a slab-on-ground building since additional sources of oxygen due to advective flow or diffusion through the slab are ignored. As such the model can be used for screening sites for further investigation.

  7. Ultrafast vapourization dynamics of laser-activated polymeric microcapsules

    Science.gov (United States)

    Lajoinie, Guillaume; Gelderblom, Erik; Chlon, Ceciel; Böhmer, Marcel; Steenbergen, Wiendelt; de Jong, Nico; Manohar, Srirang; Versluis, Michel

    2014-04-01

    Precision control of vapourization, both in space and time, has many potential applications; however, the physical mechanisms underlying controlled boiling are not well understood. The reason is the combined microscopic length scales and ultrashort timescales associated with the initiation and subsequent dynamical behaviour of the vapour bubbles formed. Here we study the nanoseconds vapour bubble dynamics of laser-heated single oil-filled microcapsules using coupled optical and acoustic detection. Pulsed laser excitation leads to vapour formation and collapse, and a simple physical model captures the observed radial dynamics and resulting acoustic pressures. Continuous wave laser excitation leads to a sequence of vapourization/condensation cycles, the result of absorbing microcapsule fragments moving in and out of the laser beam. A model incorporating thermal diffusion from the capsule shell into the oil core and surrounding water reveals the mechanisms behind the onset of vapourization. Excellent agreement is observed between the modelled dynamics and experiment.

  8. Speciation of mercury in fish samples by flow injection catalytic cold vapour atomic absorption spectrometry.

    Science.gov (United States)

    Zhang, Yanlin; Adeloju, Samuel B

    2012-04-01

    A rapid flow injection catalytic cold vapour atomic absorption spectrometric (FI-CCV-AAS) method is described for speciation and determination of mercury in biological samples. Varying concentrations of NaBH(4) were employed for mercury vapour generation from inorganic and mixture of inorganic and organic (total) Hg. The presence of Fe(3+), Cu(2+) and thiourea had catalytic effect on mercury vapour generation from methylmercury (MeHg) and, when together, Cu(2+) and thiourea had synergistic catalytic effect on the vapour generation. Of the two metal ions, Fe(3+) gave the best sensitivity enhancement, achieving the same sensitivity for MeHg and inorganic Hg(2+). Due to similarity of resulting sensitivity, Hg(2+) was used successfully as a primary standard for quantification of inorganic and total Hg. The catalysis was homogeneous in nature, and it was assumed that the breaking of the C-Hg bond was facilitated by the delocalization of the 5d electron pairs in Hg atom. The extraction of MeHg and inorganic mercury (In-Hg) in fish samples were achieved quantitatively with hydrochloric acid in the presence of thiourea and determined by FI-CCV-AAS. The application of the method to the quantification of mercury species in a fish liver reference material DOLT-4 gave 91.5% and 102.3% recoveries for total and methyl mercury, respectively. The use of flow injection enabled rapid analysis with a sample throughput of 180 h(-1).

  9. Epitaxial growth of HgTe by a MOVPE process

    Energy Technology Data Exchange (ETDEWEB)

    Irvine, S.J.C.; Mullin, J.B.; Royle, A. (Royal Signals and Radar Establishment, Malvern (UK))

    1982-03-01

    Epitaxial layers of HgTe have been grown onto insulating CdTe substrates by the pyrolysis of (C/sub 2/H/sub 5/)/sub 2/Te in the presence of Hg vapour using a H/sub 2/ flow system. Temperature-dependent Hall effect and conductivity measurements have shown that the electrical properties of the layers are comparable with good quality bulk HgTe.

  10. 3-D Modeling of Double-Diffusive Convection During Directional Solidification of a Non-Dilute Alloy with Application to the HgCdTe Growth Under Microgravity Conditions

    Science.gov (United States)

    Bune, Andris V.; Gillies, Donald C.; Lehoczky, Sandor L.

    1998-01-01

    A numerical calculation for a non-dilute alloy solidification was performed using the FIDAP finite element code. For low growth velocities plane front solidification occurs. The location and the shape of the interface was determined using melting temperatures from the HgCdTe liquidus curve. The low thermal conductivity of the solid HgCdTe causes thermal short circuit through the ampoule walls, resulting in curved isotherms in the vicinity of the interface. Double-diffusive convection in the melt is caused by radial temperature gradients and by material density inversion with temperature. Cooling from below and the rejection at the solid-melt interface of the heavier HgTe-rich solute each tend to reduce convection. Because of these complicating factors dimensional rather then non-dimensional modeling was performed. Estimates of convection contributions for various gravity conditions was performed parametrically. For gravity levels higher then 1 0 -7 of earth's gravity it was found that the maximum convection velocity is extremely sensitive to gravity vector orientation and can be reduced at least by factor of 50% for precise orientation of the ampoule in the microgravity environment. The predicted interface shape is in agreement with one obtained experimentally by quenching. The results of 3-D modeling are compared with previous 2-D finding. A video film featuring melt convection will be presented.

  11. [CO2-exchange of some lichens after absorption of water vapour].

    Science.gov (United States)

    Bertsch, A

    1966-06-01

    The relation between CO2-exchange and water content of the lichens Evernia divaricata, E. prunastri, Ramalina thrausta and R. farinacea was investigated. The dry thalli absorb water vapour up to 70% of their dry weight. This uptake of water vapour is sufficient to reactivate the CO2-exchange. In equilibrium with the vapour pressure of the nearly saturated air the apparent CO2-uptake amounts to 90% of the value obtained after imbibition with liquid water. Even in unsaturated air the CO2-exchange is reactivated and the compensation point is reached between 80 and 85% relative humidity (saturation deficit at 10°C: 1,85-1,38 mm Hg).

  12. Proposal for a revised reference concentration (RfC) for mercury vapour in adults.

    Science.gov (United States)

    Beate, Lettmeier; Stephan, Boese-O'Reilly; Gustav, Drasch

    2010-08-01

    Worldwide, approximately 30-50 millions of people are living in small scale gold mining areas and are primarily burdened by mercury vapour. In the frame of our study, 306 mercury (Hg) vapour burdened adults, working and/ or living in two small scale gold mining areas in Zimbabwe and Tanzania and 58 volunteers from near-by unburdened communities were medically investigated. In addition, blood, urine and hair samples from each participant were analyzed for mercury. Altogether, 26 anamnestic and 24 clinical signs and symptoms, which may be caused by Hg vapour, were evaluated. Multivariate analysis was performed to investigate the influence of the mercury concentration in the bio-monitors on the evaluated anamnestic and clinical signs and symptoms taking into account age, gender, health status, alcohol consumption, use of pesticides and gasoline sniffing. Out of the resulting correlations between concentration and effect, ROC-curves were calculated to determine best estimates of the cut-off-values in the bio monitors. For the parameters ataxia of gait and sadness cut-off-values of 4.7 and 3.6 microg Hg/g crea in urine were calculated. These values were converted to a rounded LOAEL of 3.5 microg Hg vapour/m(3) air. In analogy to the US EPA Report (U.S. Environmental Protection Agency 1997) and the European Position Paper (Pirrone et al. 2001), uncertainty factors of 30 and 50 were applied, resulting in a proposed reference concentration (RfC) in ambient air of 0.1 microg Hg vapour/m(3) and 0.07 microg Hg vapour/m(3), respectively.

  13. Relaxation of quadrupole orientation in an optically pumped alkali vapour

    Energy Technology Data Exchange (ETDEWEB)

    Bernabeu, E.; Tornos, J.

    1985-04-01

    The relaxation of quadrupole orientation (alignment) in an optically pumped alkali vapour is theoretically studied by taking into account the relaxation processes by alkali-buffer gas, alkali-alkali with spin exchange and alkali-cell wall (diffusion process) collisions. The relaxation transients of the quadrupole orientation are obtained by introducing a first-order weak-pumping approximation (intermediate pumping) less restrictive than the usually considered (zeroth order) one.

  14. Vapour Intrusion into Buildings - A Literature Review

    Science.gov (United States)

    This chapter provides a review of recent research on vapour intrusion of volatile organic compounds (VOCs) into buildings. The chapter builds on a report from Tillman and Weaver (2005) which reviewed the literature on vapour intrusion through 2005. Firstly, the term ‘vapour intru...

  15. Effect of paint on vapour resistivity in plaster

    Directory of Open Access Journals (Sweden)

    de Villanueva, L.

    2008-12-01

    Full Text Available The vapour resistivity of plaster coatings such as paint and their effectiveness as water repellents were studied in several types of plaster. To this end, painted, unpainted and pigmented specimens were tested. Experimental values were collected on diffusion and vapour permeability, or its inverse, water vapour resistivity.The data obtained were very useful for evaluating moisture exchange between plaster and the surrounding air, both during initial drying and throughout the life of the material. They likewise served as a basis for ensuring the proper evacuation of water vapour in walls, and use of the capacity of the porous network in plaster products to regulate moisture content or serve as a water vapour barrier to avoid condensation.Briefly, the research showed that pigments, water-based paints and silicon-based water repellents scantly raised vapour resistance. Plastic paints, enamels and lacquers, however, respectively induced five-, ten- and twenty-fold increases in vapour resistivity, on average.Se estudia el fenómeno de la resistividad al vapor de los de yeso y el efecto impermeabilizante que producen los recubrimientos de pintura sobre diversos tipos de yeso y escayola. Para ello, se ensayan probetas desnudas y recubiertas con distintos tipos de pintura, así como coloreados en masa. Se obtienen valores experimentales de la difusividad o permeabilidad al vapor o su inverso la resistividad al vapor de agua.Los datos obtenidos son muy útiles para valorar el fenómeno del intercambio de humedad entre el yeso y el ambiente, tanto durante el proceso de su secado inicial, como en el transcurso de su vida. Así como para disponer soluciones adecuadas para la evacuación del vapor de agua a través de los cerramientos, para utilizar la capacidad de regulación de la humedad, que proporciona el entramado poroso de los productos de yeso, o para impedir el paso del vapor de agua y evitar condensaciones.Como resumen de la investigación, se

  16. Chemical thermodynamics of Hg1201 and Hg1223 phases

    Science.gov (United States)

    Tsuchiya, Tetsuo; Fueki, Kazuo; Koyama, Tadashi

    1998-03-01

    The decomposition equilibrium of Hg1201 and Hg1223 was studied using a thermomicrobalance. A thermodynamic diagram representing the stability domains of Hg1201 and Hg1223 was constructed. Using the diagram, it was shown that Hg1201 is metastable at 800°C and that Hg1223 is stable at 660°C due to the formation of an atmosphere of mercury vapor and oxygen formed by the decomposition of excess HgO. Chemical analysis revealed that the valence of Hg is +2 regardless of the oxygen content. The dependence of Tc on the oxygen content was also studied.

  17. Moisture diffusion and permeability characteristics of hydroxypropylmethylcellulose and hard gelatin capsules.

    Science.gov (United States)

    Barham, Ahmad S; Tewes, Frederic; Healy, Anne Marie

    2015-01-30

    The primary objective of this paper is to compare the sorption characteristics of hydroxypropylmethylcellulose (HPMC) and hard gelatin (HG) capsules and their ability to protect capsule contents. Moisture sorption and desorption isotherms for empty HPMC and HG capsules have been investigated using dynamic vapour sorption (DVS) at 25°C. All sorption studies were analysed using the Young-Nelson model equations which distinguishes three moisture sorption types: monolayer adsorption moisture, condensation and absorption. Water vapour diffusion coefficients (D), solubility (S) and permeability (P) parameters of the capsule shells were calculated. ANOVA was performed with the Tukey comparison test to analyse the effect of %RH and capsule type on S, P, and D parameters. The moisture uptake of HG capsules were higher than HPMC capsules at all %RH conditions studied. It was found that values of D and P across HPMC capsules were greater than for HG capsules at 0-40 %RH; whereas over the same %RH range S values were higher for HG than for HPMC capsules. S values decreased gradually as the %RH was increased up to 60% RH. To probe the effect of moisture ingress, spray dried lactose was loaded into capsules. Phase evolution was characterised by scanning electron microscopy (SEM), X-ray powder diffraction (XRD), and differential scanning calorimetry (DSC). The capsules under investigation are not capable of protecting spray dried lactose from induced solid state changes as a result of moisture uptake. For somewhat less moisture sensitive formulations, HPMC would appear to be a better choice than HG in terms of protection of moisture induced deterioration. Copyright © 2014 Elsevier B.V. All rights reserved.

  18. Intercomparison on measurement of water vapour permeability

    DEFF Research Database (Denmark)

    Hansen, Kurt Kielsgaard

    Three different materials are tested - hard woodfibre board - damp proof course - underlay for roofing The water vapour permeability has been measured according to EN ISO 12572 (2001).......Three different materials are tested - hard woodfibre board - damp proof course - underlay for roofing The water vapour permeability has been measured according to EN ISO 12572 (2001)....

  19. Gas and vapour detection using polypyrrole

    NARCIS (Netherlands)

    Leur, R.H.M. van de; Waal, A. van der

    1999-01-01

    The vapours of organic solvents like toluene, butanon, and ethanol do effect the electrical conductivity of electrochemically synthesised polypyrrole. This property allows the use of polypyrrole in sensors for vapour detection. The conductivity is also a function of temperature and the history of

  20. Surface polish of PLA parts in FDM using dichloromethane vapour

    Directory of Open Access Journals (Sweden)

    Jin Yifan

    2017-01-01

    Full Text Available Fused deposition modelling has become one of the most diffused rapid prototyping techniques, which is widely used to fabricate prototypes. However, further application of this technology is severely limited by poor surface roughness. Thus it is necessary to adopt some operations to improve surface quality. Chemical finishing is typically employed to finish parts in fused deposition modelling (FDM. The purpose of this paper is to decrease the surface roughness for polylactic acid (PLA parts in FDM. The chemical reaction mechanism during the treating process is analysed. Then NaOH solution and dichloromethane vapour are used to treat FDM specimens respectively. A 3D laser microscope has been applied to assess the effects in terms of surface topography and roughness. The experimental results show that treatment using dichloromethane vapour performs much better than NaOH solution. Compared with the untreated group, surface roughness obtained through vapour treatment decreases by 88 per cent. This research has been conducted to provide a better method to treat PLA parts using chemical reagents.

  1. Bioindication of volcanic mercury (Hg) deposition around Mt Etna (Sicily)

    Science.gov (United States)

    Martin, R.; Witt, M. L.; Sawyer, G. M.; Watt, S.; Bagnato, E.; Calabrese, S.; Aiuppa, A.; Delmelle, P.; Pyle, D. M.; Mather, T. A.

    2012-12-01

    Mt. Etna is a major natural source of Hg to the Mediterranean region. Total mercury concentrations, [Hg]tot, in Castanea sativa (sweet chestnut) leaves sampled 7-13 km from Etna's vents (during six campaigns in 2005-2011) were determined using atomic absorption spectroscopy. [Hg]tot in C. sativa was greatest on Etna's SE flank reflecting Hg deposition from the typically overhead volcanic plume. When adjusted for leaf age, [Hg]tot in C. sativa also increased with recent eruptive activity. [Hg]tot in C. sativa was not controlled by [Hg]tot in soils, which instead was greatest on the (upwind) NW flank and correlated strongly with soil organic matter (% Org). Our results suggest that at least ~1% of Hg emitted from Etna is deposited proximally, supporting recent measurement and model results which indicate that GEM (Hg0; the dominant form of Hg in high temperature magmatic gases) is oxidised rapidly to RGM and Hgp in ambient temperature volcanic plumes. Samples of C. sativa and soils were also collected in July and September 2012 alongside SO2 and acid gas diffusion tube samples. These new samples will enable us to investigate Hg accumulation over a single growth season with reference to the exposure of vegetation to volcanic gases and particles.

  2. Measurement of water vapour transport through a porous non-hygroscopic material in a temperature gradient

    DEFF Research Database (Denmark)

    Hansen, Thor; Padfield, Tim; Hansen, Kurt Kielsgaard

    2014-01-01

    This was an experiment to identify the driving potential for water vapour diffusion through porous materials in a temperature gradient. The specimen of mineral fibre insulation was placed between a space with controlled temperature and relative humidity and a space with a controlled, higher...

  3. The speed of sound in a gas–vapour bubbly liquid

    NARCIS (Netherlands)

    Prosperetti, Andrea

    2015-01-01

    In addition to the vapour of the liquid, bubbles in cavitating flows usually contain also a certain amount of permanent gas that diffuses out of the liquid as they grow. This paper presents a simplified linear model for the propagation of monochromatic pressure waves in a bubbly liquid with these ch

  4. Boundary layer chemical vapour synthesis of self-organised ferromagnetically filled radial-carbon-nanotube structures.

    Science.gov (United States)

    Boi, Filippo S; Wilson, Rory M; Mountjoy, Gavin; Ibrar, Muhammad; Baxendale, Mark

    2014-01-01

    Boundary layer chemical vapour synthesis is a new technique that exploits random fluctuations in the viscous boundary layer between a laminar flow of pyrolysed metallocene vapour and a rough substrate to yield ferromagnetically filled radial-carbon-nanotube structures departing from a core agglomeration of spherical nanocrystals individually encapsulated by graphitic shells. The fluctuations create the thermodynamic conditions for the formation of the central agglomeration in the vapour which subsequently defines the spherically symmetric diffusion gradient that initiates the radial growth. The radial growth is driven by the supply of vapour feedstock by local diffusion gradients created by endothermic graphitic-carbon formation at the vapour-facing tips of the individual nanotubes and is halted by contact with the isothermal substrate. The radial structures are the dominant product and the reaction conditions are self-sustaining. Ferrocene pyrolysis yields three common components in the nanowire encapsulated by multiwall carbon nanotubes, Fe3C, α-Fe, and γ-Fe. Magnetic tuning in this system can be achieved through the magnetocrystalline and shape anisotropies of the encapsulated nanowire. Here we demonstrate proof that alloying of the encapsulated nanowire is an additional approach to tuning of the magnetic properties of these structures by synthesis of radial-carbon-nanotube structures with γ-FeNi encapsulated nanowires.

  5. COMPARISON OF CHARACTERIZATION TECHNIQUES IN P-ON-N HgCdTe LWIR PHOTODIODES TECHNOLOGY

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    In this paper standard techniques for characterization of HgCdTe liquid phase epitaxial layers (LPE) were presented. The performance of long wavelength p-on-n HgCdTe photodiodes fabricated by arsenic diffusion was described. The correlation between LPE HgCdTe material parameters and properties of the infrared photodiodes was demonstrated.

  6. Autonomous Chemical Vapour Detection by Micro UAV

    Directory of Open Access Journals (Sweden)

    Kent Rosser

    2015-12-01

    Full Text Available The ability to remotely detect and map chemical vapour clouds in open air environments is a topic of significant interest to both defence and civilian communities. In this study, we integrate a prototype miniature colorimetric chemical sensor developed for methyl salicylate (MeS, as a model chemical vapour, into a micro unmanned aerial vehicle (UAV, and perform flights through a raised MeS vapour cloud. Our results show that that the system is capable of detecting MeS vapours at low ppm concentration in real-time flight and rapidly sending this information to users by on-board telemetry. Further, the results also indicate that the sensor is capable of distinguishing “clean” air from “dirty”, multiple times per flight, allowing us to look towards autonomous cloud mapping and source localization applications. Further development will focus on a broader range of integrated sensors, increased autonomy of detection and improved engineering of the system.

  7. [Turpentined vapour baths with coniferous oil].

    Science.gov (United States)

    Raynal, Cécile

    2007-10-01

    This article presents the history of turpentined vapour baths used to treat rheumatismes. In the same time appeared patent medicines made with coniferous oil, sold by chemist near those baths establishments.

  8. A liquid crystalline chirality balance for vapours

    OpenAIRE

    Ohzono, Takuya; Yamamoto, Takahiro; Fukuda, Jun-Ichi

    2014-01-01

    Chiral discrimination of vapours plays an important role in olfactory perception of biological systems and its realization by artificial sensors has been an intriguing challenge. Here, we report a simple method that tangibly visualizes the chirality of a diverse variety of molecules dissolved from vapours with high sensitivity, by making use of a structural change in a periodic microstructure of a nematic liquid crystal confined in open microchannels. This microstructure is accompanied by a t...

  9. Hg-Mask Coronagraph

    Science.gov (United States)

    Bourget, P.; Veiga, C. H.; Vieira Martins, R.; Assus, P.; Colas, F.

    In order to optimize the occulting process of a Lyot coronagraph and to provide a high dynamic range imaging, a new kind of occulting disk has been developed at the National Observatory of Rio de Janeiro. A mercury (Hg) drop glued onto an optical window by molecular cohesion and compressed by a pellicle film is used as the occulting disk. The minimum of the superficial tension potential function provides an optical precision (lambda/100) of the toric free surface of the mercury. This process provides a size control for the adaptation to the seeing conditions and to the apparent diameter of a resolved object, and in the case of adaptive optics, to the Airy diameter fraction needed. The occultation is a three dimensional process near the focal plane on the toric free surface that provides an apodization of the occultation. The Hg-Mask coronagraph has been projected for astrometric observations of faint satellites near to Jovian planets and works since 2000 at the 1.6 m telescope of the Pico dos Dias Observatory (OPD - Brazil).

  10. A liquid crystalline chirality balance for vapours

    Science.gov (United States)

    Ohzono, Takuya; Yamamoto, Takahiro; Fukuda, Jun-Ichi

    2014-04-01

    Chiral discrimination of vapours plays an important role in olfactory perception of biological systems and its realization by artificial sensors has been an intriguing challenge. Here, we report a simple method that tangibly visualizes the chirality of a diverse variety of molecules dissolved from vapours with high sensitivity, by making use of a structural change in a periodic microstructure of a nematic liquid crystal confined in open microchannels. This microstructure is accompanied by a topological line defect of a zigzag form with equal lengths of ‘zig’ and ‘zag.’ We find that a tiny amount of vapour of chiral molecules injected onto the liquid crystal induces the imbalance of ‘zig’ and ‘zag’ depending on its enantiomeric excess within a few seconds. Our liquid-crystal-based ‘chirality balance’ offers a simple, quick and versatile chirality-sensing/-screening method for gas-phase analysis (for example, for odours, environmental chemicals or drugs).

  11. High removal efficacy of Hg(II) and MeHg(II) ions from aqueous solution by organoalkoxysilane-grafted lignocellulosic waste biomass.

    Science.gov (United States)

    Saman, Norasikin; Johari, Khairiraihanna; Song, Shiow-Tien; Kong, Helen; Cheu, Siew-Chin; Mat, Hanapi

    2017-03-01

    An effective organoalkoxysilanes-grafted lignocellulosic waste biomass (OS-LWB) adsorbent aiming for high removal towards inorganic and organic mercury (Hg(II) and MeHg(II)) ions was prepared. Organoalkoxysilanes (OS) namely mercaptoproyltriethoxylsilane (MPTES), aminopropyltriethoxylsilane (APTES), aminoethylaminopropyltriethoxylsilane (AEPTES), bis(triethoxysilylpropyl) tetrasulfide (BTESPT), methacrylopropyltrimethoxylsilane (MPS) and ureidopropyltriethoxylsilane (URS) were grafted onto the LWB using the same conditions. The MPTES grafted lignocellulosic waste biomass (MPTES-LWB) showed the highest adsorption capacity towards both mercury ions. The adsorption behavior of inorganic and organic mercury ions (Hg(II) and MeHg(II)) in batch adsorption studies shows that it was independent with pH of the solutions and dependent on initial concentration, temperature and contact time. The maximum adsorption capacity of Hg(II) was greater than MeHg(II) which respectively followed the Temkin and Langmuir models. The kinetic data analysis showed that the adsorptions of Hg(II) and MeHg(II) onto MPTES-LWB were respectively controlled by the physical process of film diffusion and the chemical process of physisorption interactions. The overall mechanism of Hg(II) and MeHg(II) adsorption was a combination of diffusion and chemical interaction mechanisms. Regeneration results were very encouraging especially for the Hg(II); this therefore further demonstrated the potential application of organosilane-grafted lignocellulosic waste biomass as low-cost adsorbents for mercury removal process.

  12. Combustion dynamics of low vapour pressure nanofuel droplets

    Science.gov (United States)

    Pandey, Khushboo; Chattopadhyay, Kamanio; Basu, Saptarshi

    2017-07-01

    Multiscale combustion dynamics, shape oscillations, secondary atomization, and precipitate formation have been elucidated for low vapour pressure nanofuel [n-dodecane seeded with alumina nanoparticles (NPs)] droplets. Dilute nanoparticle loading rates (0.1%-1%) have been considered. Contrary to our previous studies of ethanol-water blend (high vapour pressure fuel), pure dodecane droplets do not exhibit internal boiling after ignition. However, variation in surface tension due to temperature causes shape deformations for pure dodecane droplets. In the case of nanofuels, intense heat release from the enveloping flame leads to the formation of micron-size aggregates (of alumina NPS) which serve as nucleation sites promoting heterogeneous boiling. Three boiling regimes (A, B, and C) have been identified with varying bubble dynamics. We have deciphered key mechanisms responsible for the growth, transport, and rupture of the bubbles. Bubble rupture causes ejections of liquid droplets termed as secondary atomization. Ejection of small bubbles (mode 1) resembles the classical vapour bubble collapse mechanism near a flat free surface. However, large bubbles induce severe shape deformations as well as bulk oscillations. Rupture of large bubbles results in high speed liquid jet formation which undergoes Rayleigh-Plateau tip break-up. Both modes contribute towards direct fuel transfer from the droplet surface to flame envelope bypassing diffusion limitations. Combustion lifetime of nanofuel droplets consequently has two stages: stage I (where bubble dynamics are dominant) and stage II (formation of gelatinous mass due to continuous fuel depletion; NP agglomeration). In the present work, variation of flame dynamics and spatio-temporal heat release (HR) have been analysed using high speed OH* chemiluminescence imaging. Fluctuations in droplet shape and flame heat release are found to be well correlated. Droplet flame is bifurcated in two zones (I and II). Flame response is

  13. Modelling vapour transport in Surtseyan bombs

    Science.gov (United States)

    McGuinness, Mark J.; Greenbank, Emma; Schipper, C. Ian

    2016-05-01

    We address questions that arise if a slurry containing liquid water is enclosed in a ball of hot viscous vesicular magma ejected as a bomb in the context of a Surtseyan eruption. We derive a mathematical model for transient changes in temperature and pressure due to flashing of liquid water to vapour inside the bomb. The magnitude of the transient pressure changes that are typically generated are calculated together with their dependence on material properties. A single criterion to determine whether the bomb will fragment as a result of the pressure changes is derived. Timescales for ejection of water vapour from a bomb that remains intact are also revealed.

  14. Engineering steps for optimizing high temperature LWIR HgCdTe photodiodes

    Science.gov (United States)

    Madejczyk, Pawel; Gawron, Waldemar; Martyniuk, Piotr; Keblowski, Artur; Pusz, Wioletta; Pawluczyk, Jaroslaw; Kopytko, Malgorzata; Rutkowski, Jaroslaw; Rogalski, Antoni; Piotrowski, Jozef

    2017-03-01

    The authors report on energy gap engineering solutions to improve the high-temperature performance of long-wave infrared (LWIR) HgCdTe photodiodes. Metalorganic chemical vapour deposition (MOCVD) technology with a wide range of composition and donor/acceptor doping and without ex-situ post grown annealing seems to be an excellent tool for HgCdTe heterostructure epitaxial growth. The heterojunction HgCdTe photovoltaic device based on epitaxial graded gap structures integrated with Auger-suppression is a magnificent solution for high operating temperature (HOT) infrared detectors. The thickness, composition and doping of HgCdTe heterostructure were optimized with respect to photoelectrical parameters like dark current, the responsivity and the response time. In this paper we focus on graded interface abruptness in the progressive optimization.

  15. Developments in vapour cloud explosion blast modeling

    NARCIS (Netherlands)

    Mercx, W.P.M.; Berg, A.C. van den; Hayhurst, C.J.; Robertson, N.J.; Moran, K.C.

    2000-01-01

    TNT Equivalency methods are widely used for vapour cloud explosion blast modeling. Presently, however, other types of models are available which do not have the fundamental objections TNT Equivalency models have. TNO Multi-Energy method is increasingly accepted as a more reasonable alternative to be

  16. Water vapour loss measurements on human skin.

    NARCIS (Netherlands)

    Valk, Petrus Gerardus Maria van der

    1984-01-01

    In this thesis, the results of a series of investigations into the barrier function of human skin are presented. In these investigations, the barrier function was assessed by water vapour loss measurements of the skin using a method based on gradient estimation.... Zie: Summary and conclusions

  17. Virucidal efficacy of hydrogen peroxide vapour disinfection

    NARCIS (Netherlands)

    Tuladhar, E.; Terpstra, P.; Koopmans, M.; Duizer, E.

    2012-01-01

    Background: Viral contamination of surfaces is thought to be important in transmission. Chemical disinfection can be an effective means of intervention, but little is known about the virucidal efficacy of hydrogen peroxide vapour (HPV) against enteric and respiratory viruses. Aim: To measure the

  18. Virucidal efficacy of hydrogen peroxide vapour disinfection

    NARCIS (Netherlands)

    Tuladhar, E.; Terpstra, P.; Koopmans, M.; Duizer, E.

    2012-01-01

    Background: Viral contamination of surfaces is thought to be important in transmission. Chemical disinfection can be an effective means of intervention, but little is known about the virucidal efficacy of hydrogen peroxide vapour (HPV) against enteric and respiratory viruses. Aim: To measure the vir

  19. The experiment on the saturation polarization of Rb vapour

    Institute of Scientific and Technical Information of China (English)

    Huang Xiang-You; You Pei-Lin; Du Wei-Min

    2004-01-01

    @@ A cylindrical capacitor containing rubidium vapour is made. The capacitance of it at. different voltages is measured under a certain Rb vapour pressure. The experimental C-V curve shows that the saturation polarization of Rb vapour is easily observed. The experiment further supports the idea that the Rb atom has a large permanent electric dipole moment.

  20. Modelling and interpreting the isotopic composition of water vapour in convective updrafts

    Directory of Open Access Journals (Sweden)

    M. Bolot

    2013-08-01

    Full Text Available The isotopic compositions of water vapour and its condensates have long been used as tracers of the global hydrological cycle, but may also be useful for understanding processes within individual convective clouds. We review here the representation of processes that alter water isotopic compositions during processing of air in convective updrafts and present a unified model for water vapour isotopic evolution within undiluted deep convective cores, with a special focus on the out-of-equilibrium conditions of mixed-phase zones where metastable liquid water and ice coexist. We use our model to show that a combination of water isotopologue measurements can constrain critical convective parameters, including degree of supersaturation, supercooled water content and glaciation temperature. Important isotopic processes in updrafts include kinetic effects that are a consequence of diffusive growth or decay of cloud particles within a supersaturated or subsaturated environment; isotopic re-equilibration between vapour and supercooled droplets, which buffers isotopic distillation; and differing mechanisms of glaciation (droplet freezing vs. the Wegener–Bergeron–Findeisen process. As all of these processes are related to updraft strength, particle size distribution and the retention of supercooled water, isotopic measurements can serve as a probe of in-cloud conditions of importance to convective processes. We study the sensitivity of the profile of water vapour isotopic composition to differing model assumptions and show how measurements of isotopic composition at cloud base and cloud top alone may be sufficient to retrieve key cloud parameters.

  1. Transport mechanisms through PE-CVD coatings: influence of temperature, coating properties and defects on permeation of water vapour

    Science.gov (United States)

    Kirchheim, Dennis; Jaritz, Montgomery; Mitschker, Felix; Gebhard, Maximilian; Brochhagen, Markus; Hopmann, Christian; Böke, Marc; Devi, Anjana; Awakowicz, Peter; Dahlmann, Rainer

    2017-03-01

    Gas transport mechanisms through plastics are usually described by the temperature-dependent Arrhenius-model and compositions of several plastic layers are represented by the CLT. When it comes to thin films such as plasma-enhanced chemical vapour deposition (PE-CVD) or plasma-enhanced atomic layer deposition (PE-ALD) coatings on substrates of polymeric material, a universal model is lacking. While existing models describe diffusion through defects, these models presume that permeation does not occur by other means of transport mechanisms. This paper correlates the existing transport models with data from water vapour transmission experiments.

  2. Electron collisions by metal atom vapours

    Energy Technology Data Exchange (ETDEWEB)

    Marinkovic, B.P. [Institute of Physics, P.O. Box 68, 11080, Belgrade (Serbia)]. E-mail: bratislav.marinkovic@phy.bg.ac.yu; Pejcev, V. [Institute of Physics, P.O. Box 68, 11080, Belgrade (Serbia); Faculty of Natural Sciences, University of Kragujevac (Serbia); Filipovic, D.M. [Institute of Physics, P.O. Box 68, 11080, Belgrade (Serbia); Faculty of Physics, University of Belgrade, P.O. Box 368, 11001 Belgrade (Serbia); Sevic, D. [Institute of Physics, P.O. Box 68, 11080, Belgrade (Serbia); Milisavljevic, S. [Institute of Physics, P.O. Box 68, 11080, Belgrade (Serbia); Predojevic, B. [Institute of Physics, P.O. Box 68, 11080, Belgrade (Serbia); Faculty of Natural Sciences, University of Banja Luka, Republic of Srpska (Bosnia and Herzegowina)

    2007-03-15

    Differential cross sections (DCS) for the elastic electron scattering and electron excitation of metal atom vapours are presented and discussed. Absolute scale was obtained by normalization procedure where generalized oscillator strengths were fitted to terminate at forward scattering function which leads to optical oscillator strength at zero momentum transfer. DCSs are compared with other available experimental and theoretical results and their importance for our understanding of basic electron atom interactions is pointed out.

  3. Interactions of fission product vapours with aerosols

    Energy Technology Data Exchange (ETDEWEB)

    Benson, C.G.; Newland, M.S. [AEA Technology, Winfrith (United Kingdom)

    1996-12-01

    Reactions between structural and reactor materials aerosols and fission product vapours released during a severe accident in a light water reactor (LWR) will influence the magnitude of the radiological source term ultimately released to the environment. The interaction of cadmium aerosol with iodine vapour at different temperatures has been examined in a programme of experiments designed to characterise the kinetics of the system. Laser induced fluorescence (LIF) is a technique that is particularly amenable to the study of systems involving elemental iodine because of the high intensity of the fluorescence lines. Therefore this technique was used in the experiments to measure the decrease in the concentration of iodine vapour as the reaction with cadmium proceeded. Experiments were conducted over the range of temperatures (20-350{sup o}C), using calibrated iodine vapour and cadmium aerosol generators that gave well-quantified sources. The LIF results provided information on the kinetics of the process, whilst examination of filter samples gave data on the composition and morphology of the aerosol particles that were formed. The results showed that the reaction of cadmium with iodine was relatively fast, giving reaction half-lives of approximately 0.3 s. This suggests that the assumption used by primary circuit codes such as VICTORIA that reaction rates are mass-transfer limited, is justified for the cadmium-iodine reaction. The reaction was first order with respect to both cadmium and iodine, and was assigned as pseudo second order overall. However, there appeared to be a dependence of aerosol surface area on the overall rate constant, making the precise order of the reaction difficult to assign. The relatively high volatility of the cadmium iodide formed in the reaction played an important role in determining the composition of the particles. (author) 23 figs., 7 tabs., 22 refs.

  4. Modelling the budget of middle atmospheric water vapour isotopes

    Directory of Open Access Journals (Sweden)

    A. Zahn

    2006-01-01

    Full Text Available A one-dimensional chemistry model is applied to study the stable hydrogen (D and stable oxygen isotope (17O, 18O composition of water vapour in stratosphere and mesosphere. In the troposphere, this isotope composition is determined by 'physical'' fractionation effects, that are phase changes (e.g. during cloud formation, diffusion processes (e.g. during evaporation from the ocean, and mixing of air masses. Due to these processes water vapour entering the stratosphere first shows isotope depletions in D/H relative to ocean water, which are ~5 times of those in 18O/16O, and secondly is mass-dependently fractionated (MDF, i.e. changes in the isotope ratio 17O/16O are ~0.52 times of those of 18O/16O. In contrast, in the stratosphere and mesosphere 'chemical'' fractionation mechanisms, that are the production of HO due to the oxidation of methane, re-cycling of H2O via the HOx family, and isotope exchange reactions considerably enhance the isotope ratios in the water vapour imported from the troposphere. The model reasonably predicts overall enhancements of the stable isotope ratios in H2O by up to ~25% for D/H, ~8.5% for 17O/16O, and ~14% for 18O/16O in the mesosphere relative to the tropopause values. The 17O/16O and 18O/16O ratios in H2O are shown to be a measure of the relative fractions of HOx that receive the O atom either from the reservoirs O2 or O3. Throughout the middle atmosphere, MDF O2 is the major donator of oxygen atoms incorporated in OH and HO2 and thus in H2O. In the stratosphere the known mass-independent fractionation (MIF signal in O3 is in a first step transferred to the NOx family and only in a second step to HOx and H2O. In contrast to CO2, O(1D only plays a minor role in this MIF transfer. The major uncertainty in our calculation arises from poorly quantified isotope exchange reaction rate coefficients and kinetic isotope fractionation factors.

  5. Automated dispersive liquid-liquid microextraction coupled to high performance liquid chromatography - cold vapour atomic fluorescence spectroscopy for the determination of mercury species in natural water samples.

    Science.gov (United States)

    Liu, Yao-Min; Zhang, Feng-Ping; Jiao, Bao-Yu; Rao, Jin-Yu; Leng, Geng

    2017-04-14

    An automated, home-constructed, and low cost dispersive liquid-liquid microextraction (DLLME) device that directly coupled to a high performance liquid chromatography (HPLC) - cold vapour atomic fluorescence spectroscopy (CVAFS) system was designed and developed for the determination of trace concentrations of methylmercury (MeHg(+)), ethylmercury (EtHg(+)) and inorganic mercury (Hg(2+)) in natural waters. With a simple, miniaturized and efficient automated DLLME system, nanogram amounts of these mercury species were extracted from natural water samples and injected into a hyphenated HPLC-CVAFS for quantification. The complete analytical procedure, including chelation, extraction, phase separation, collection and injection of the extracts, as well as HPLC-CVAFS quantification, was automated. Key parameters, such as the type and volume of the chelation, extraction and dispersive solvent, aspiration speed, sample pH, salt effect and matrix effect, were thoroughly investigated. Under the optimum conditions, linear range was 10-1200ngL(-1) for EtHg(+) and 5-450ngL(-1) for MeHg(+) and Hg(2+). Limits of detection were 3.0ngL(-1) for EtHg(+) and 1.5ngL(-1) for MeHg(+) and Hg(2+). Reproducibility and recoveries were assessed by spiking three natural water samples with different Hg concentrations, giving recoveries from 88.4-96.1%, and relative standard deviations <5.1%.

  6. Metal Vapour Lasers: Physics, Engineering and Applications

    Science.gov (United States)

    Little, Christopher E.

    1999-03-01

    Metal Vapour Lasers Christopher E. Little University of St Andrews, St Andrews, Scotland Since the first successful demonstration of a metal vapour laser (MVL) in 1962, this class of laser has become widely used in a broad range of fields including precision materials processing, isotope separation and medicine. The MVLs that are used today have a range of impressive characteristics that are not readily available using other technologies. In particular, the combination of high average output powers, pulse recurrence frequencies and beam quality available from green/yellow Cu vapour lasers (CVLs) and Cu bromide lasers, coupled with the high-quality, multiwatt ultraviolet (265-289 nm) radiation that can be produced using simple nonlinear optical techniques, means that Cu lasers will continue to be important for many years. Metal Vapour Lasers covers all the most commercially important and scientifically interesting pulsed and continuous wave (CW) gas-discharge MVLs, and includes device histories, operating characteristics, engineering, kinetics, commercial exploitation and applications. Short descriptions of gas discharges and excitation techniques make this volume self-consistent. A comprehensive bibliography is also provided. The greater part of this book is devoted to CVLs and their variants, including new sealed-off, high-power 'kinetically enhanced' CVLs and Cu bromide lasers. However, many other self-terminating MVLs are also discussed, including the red AuVL, green/infrared MnVL and infrared BaVL. Pulsed, high-gain, high average power lasers in the UV/violet (373.7, 430.5 nm) spectral regions are represented by Sr¯+ and Ca¯+ discharge-afterglow recombination lasers. The most commercially successful of the MVLs - the CW, UV/blue cataphoretic He-Cd¯+ ion laser - is described. Hollow cathode lasers are represented in two guises: 'white light' (blue/green/red) He-Cd¯+ ion lasers and UV/infrared Ne/He-Cu¯+ ion lasers. This unique volume is an

  7. [Qualitative Determination of Organic Vapour Using Violet and Visible Spectrum].

    Science.gov (United States)

    Jiang, Bo; Hu, Wen-zhong; Liu, Chang-jian; Zheng, Wei; Qi, Xiao-hui; Jiang, Ai-li; Wang, Yan-ying

    2015-12-01

    Vapours of organic matters were determined qualitatively employed with ultraviolet-visible absorption spectroscopy. Vapours of organic matters were detected using ultraviolet-visible spectrophotometer employing polyethylene film as medium, the ultraviolet and visible absorption spectra of vegetable oil vapours of soybean oil, sunflower seed oil, peanut oil, rapeseed oil, sesame oil, cotton seed oil, tung tree seed oil, and organic compound vapours of acetone, ethyl acetate, 95% ethanol, glacial acetic acid were obtained. Experimental results showed that spectra of the vegetable oil vapour and the organic compound vapour could be obtained commendably, since ultra violet and visible spectrum of polyethylene film could be deducted by spectrograph zero setting. Different kinds of vegetable oils could been distinguished commendably in the spectra since the λ(max), λ(min), number of absorption peak, position, inflection point in the ultra violet and visible spectra obtained from the vapours of the vegetable oils were all inconsistent, and the vapours of organic compounds were also determined perfectly. The method had a good reproducibility, the ultraviolet and visible absorption spectra of the vapours of sunflower seed oil in 10 times determination were absolutely the same. The experimental result indicated that polyethylene film as a kind of medium could be used for qualitative analysis of ultraviolet and visible absorption spectroscopy. The method for determination of the vapours of the vegetable oils and organic compounds had the peculiarities of fast speed analysis, well reproducibility, accuracy and reliability and low cost, and so on. Ultraviolet and visible absorption spectrum of organic vapour could provide feature information of material vapour and structural information of organic compound, and provide a novel test method for identifying vapour of compound and organic matter.

  8. The importance of the poikilohydric nature of lichens as natural tracers for delta18O of ambient vapour

    Science.gov (United States)

    Hartard, Britta; Cuntz, Matthias; Lakatos, Michael; Máguas, Cristina

    2010-05-01

    The stable isotope composition of water is routinely used as a tracer to study water exchange processes in vascular plants and ecosystems. To date, no study has focussed on isotope processes in poikilohydric organisms (i.e. lichens and bryophytes), where relative water content equilibrate with the surrounding humidity conditions and that are able to use distinct water sources such as precipitation, dew, fog and also water vapour. Moreover, lichens are ubiquitous organisms, and on a global scale, they are found in nearly all terrestrial ecosystems and also within these ecosystems they inhabit many microhabitats. As poikilohydric. especially green algal lichens are known to photosynthetically reactivate solely upon uptake of atmospheric moisture, even at non-saturated ambient humidity conditions. To understand basic isotope exchange processes on non-vascular plants, thallus water isotopic composition was studied in various green-algal lichens exposed to desiccation. The study indicates that lichens equilibrates with the isotopic composition of surrounding water vapour. We found that the thallus water of lichens exposed to high relative humidity shows fast isotopic equilibration with the surrounding vapour regardless of whether the lichen experiences water loss or vapour uptake. The time until isotopic equilibrium is achieved depends on the initial water status as well as on the lichen's specific morphology. It ranged from 5 to 12h in previously dried lichens to approximately 40h in lichens previously rehydrated with liquid water of distinct isotopic composition. Even though markedly slower, isotopic equilibration between leaf water and ambient vapour may also occur in homoiohydric plants exposed to high relative humidity. At low relative humidity, however, the apparent vapour pressure deficit between the evaporative sites and the ambient air and the increased stomatal diffusion resistance generally causes leaf water enrichment. In contrast, poikilohydric lichens lack

  9. Vapour Recoil Effect on a Vapour-Liquid System with a Deformable Interface

    Institute of Scientific and Technical Information of China (English)

    LIU Rong; LIU Qiu-Sheng

    2006-01-01

    @@ A new two-sided model of vapour-Iiquid layer system with a deformable interface is proposed. In this model,the vapour recoil effect on the Marangoni-Bénard instability of a thin evaporating liquid layer can be examined only when the interface deflexion is considered. The instability of a liquid layer undergoing steady evaporation induced by the coupling of vapour recoil effect and the Marangoni effect is analysed using a linear stability theory.We modify and develop the Chebyshev-Tau method to solve the instability problem of a deformable interface system by introducing a new equation at interface boundary. New instability behaviour of the system has been found and the self-amplification mechanism between the evaporation flux and the interface deflexion is discussed.

  10. Variability of water vapour in the Arctic stratosphere

    Science.gov (United States)

    Thölix, Laura; Backman, Leif; Kivi, Rigel; Karpechko, Alexey Yu.

    2016-04-01

    This study evaluates the stratospheric water vapour distribution and variability in the Arctic. A FinROSE chemistry transport model simulation covering the years 1990-2014 is compared to observations (satellite and frost point hygrometer soundings), and the sources of stratospheric water vapour are studied. In the simulations, the Arctic water vapour shows decadal variability with a magnitude of 0.8 ppm. Both observations and the simulations show an increase in the water vapour concentration in the Arctic stratosphere after the year 2006, but around 2012 the concentration started to decrease. Model calculations suggest that this increase in water vapour is mostly explained by transport-related processes, while the photochemically produced water vapour plays a relatively smaller role. The increase in water vapour in the presence of the low winter temperatures in the Arctic stratosphere led to more frequent occurrence of ice polar stratospheric clouds (PSCs) in the Arctic vortex. We perform a case study of ice PSC formation focusing on January 2010 when the polar vortex was unusually cold and allowed large-scale formation of PSCs. At the same time a large-scale persistent dehydration was observed. Ice PSCs and dehydration observed at Sodankylä with accurate water vapour soundings in January and February 2010 during the LAPBIAT (Lapland Atmosphere-Biosphere facility) atmospheric measurement campaign were well reproduced by the model. In particular, both the observed and simulated decrease in water vapour in the dehydration layer was up to 1.5 ppm.

  11. Water vapour measurements during POLINAT 1

    Energy Technology Data Exchange (ETDEWEB)

    Ovarlez, J.; Ovarlez, H. [Centre National de la Recherche Scientifique, 91 - Palaiseau (France). Lab. de Meteorologie Dynamique

    1997-12-31

    The POLINAT (POLlution from aircraft emissions In the North ATlantic flight corridor)1 experiment has been performed within the framework of the Environment Programme of the Commission of the European Community. It was devoted to the study of the pollution from aircraft in the North Atlantic flight corridor, in order to investigate the impact of pollutants emitted by aircraft on the concentrations of ozone and other trace gases in the upper troposphere and lower stratosphere. For that experiment the water vapour content was measured with a frost-point hygrometer on board of the DLR Falcon research aircraft. This instrument is described, and some selected results are given. (author) 19 refs.

  12. Is there a solar signal in lower stratospheric water vapour?

    Science.gov (United States)

    Schieferdecker, Tobias; Lossow, Stefan; Stiller, Gabriele; von Clarmann, Thomas

    2016-04-01

    A merged time series of stratospheric water vapour built from the Halogen Occultation Instrument (HALOE) and the Michelson Interferometer for Passive Atmospheric Sounding (MIPAS) data between 60 deg S and 60 deg N and 15 to 30 km, and covering the years 1992 to 2012, was analysed by multivariate linear regression, including an 11-year solar cycle proxy. Lower stratospheric water vapour was found to reveal a phase-shifted anti-correlation with the solar cycle, with lowest water vapour after solar maximum. The phase shift is composed of an inherent constant time lag of about 2 years and a second component following the stratospheric age of air. The amplitudes of the water vapour response are largest close to the tropical tropopause (up to 0.35 ppmv) and decrease with altitude and latitude. Including the solar cycle proxy in the regression results in linear trends of water vapour being negative over the full altitude/latitude range, while without the solar proxy, positive water vapour trends in the lower stratosphere were found. We conclude from these results that a solar signal seems to be generated at the tropical tropopause which is most likely imprinted on the stratospheric water vapour abundances and transported to higher altitudes and latitudes via the Brewer-Dobson circulation. Hence it is concluded that the tropical tropopause temperature at the final dehydration point of air may also be governed to some degree by the solar cycle. The negative water vapour trends obtained when considering the solar cycle impact on water vapour abundances can possibly solve the "water vapour conundrum" of increasing stratospheric water vapour abundances despite constant or even decreasing tropopause temperatures.

  13. Water vapour variability and trends in the Arctic stratosphere

    Science.gov (United States)

    Thölix, Laura; Kivi, Rigel; Backman, Leif; Karpechko, Alexey

    2014-05-01

    Water vapour in the upper troposphere-lower stratosphere (UTLS) is a radiatively and chemically important trace gas. Stratospheric water vapour also affects ozone chemistry through odd-hydrogen chemistry and formation of polar stratospheric clouds (PSC). Both transport and chemistry contribute to the extratropical lower stratospheric water vapour distribution and trends. The main sources of stratospheric water vapour are intrusion through the tropical tropopause and production from oxidation of methane. Accurate observations of UTLS water vapour are difficult to obtain due to the strong gradient in the water vapour profile over the tropopause. However, modelling the stratospheric water vapour distribution is challenging and accurate measurements are needed for model validation. Trends in Arctic water vapour will be analysed and explained in terms of contribution from different processes (transport and chemistry), using observations and chemistry transport model (CTM) simulations. Accurate water vapour soundings from Sodankylä will be used to study water vapour within the Arctic polar vortex, including process studies on formation of PSCs and dehydration. Water vapour profiles measured during the LAPBIAT atmospheric sounding campaign in Sodankylä in January 2010 indicated formation of ice clouds and dehydration. Effects on ozone chemistry will also be studied. Global middle atmospheric simulations have been performed with the FinROSE-ctm using ERA-Interim winds and temperatures. The FinROSE-ctm is a global middle atmosphere model that produces the distribution of 30 long-lived species and tracers and 14 short-lived species. The chemistry describes around 110 gas phase reactions, 37 photodissociation processes and the main heterogeneous reactions related to aerosols and polar stratospheric clouds.

  14. Fabrication and characterization of high-quality (Hg,Re)Ba sub 2 CaCu sub 2 O sub y thin films on LSAT substrates

    CERN Document Server

    Ogawa, A; Sugano, T; Adachi, S; Suzuki, K; Nakagaki, N; Enomoto, Y; Tanabe, K

    2002-01-01

    We have succeeded in fabricating high-quality (Hg,Re)Ba sub 2 CaCu sub 2 O sub y ((Hg,Re)-1212) thin films with a thickness of 300 nm on (LaAlO sub 3) sub 0 sub . sub 3 -(SrAl sub 0 sub . sub 5 Ta sub 0 sub . sub 5 O sub 3) sub 0 sub . sub 7 (LSAT) substrates. The films were fabricated by repeating the two-step process, which consists of the preparation of a precursor film and the heat treatment in Hg-vapour atmosphere. For the purpose of improving their crystal quality, the heat treatment in the final process was carried out in a lower Hg-vapour pressure for a longer time. The obtained films had a flat surface and no appreciable outgrowth. The films exhibited a T sub c value of 120 K and a J sub c value of 4.4 x 10 sup 6 A cm sup - sup 2 at 77 K in a self-field, which are substantially higher than those for the films fabricated in higher Hg-vapour atmosphere. Their electrical transport properties in magnetic fields up to 7 T were investigated. Their lower irreversibility fields at 77 K as well as the higher ...

  15. Stability studies of Hg implanted YBa$_{2}$Cu$_{3}$O$_{6+x}$

    CERN Document Server

    Araújo, J P; Wahl, U; Marques, J G; Alves, E; Amaral, V S; Lourenço, A A; Galindo, V; Von Papen, T; Senateur, J P; Weiss, F; Vantomme, A; Langouche, G; Melo, A A; Da Silva, M F A; Soares, J C; Sousa, J B

    1999-01-01

    High quality YBa$_{2}$Cu$_{3}$O$_{6+x}$ (YBCO) superconducting thin films were implanted with the radioactive $^{197m}$Hg (T$_{1/2}$ = 24 h) isotope to low fluences of 10$^{13}$ atoms/cm$^{2}$ and 60 keV energy. The lattice location and stability of the implanted Hg were studied combining the Perturbed Angular Correlation (PAC) and Emission Channeling (EC) techniques. We show that Hg can be introduced into the YBCO lattice by ion implantation into unique regular sites. The EC data show that Hg is located on a highly symmetric site on the YBCO lattice, while the PAC data suggests that Hg occupies the Cu(1) site. Annealing studies were performed under vacuum and O$_{2}$ atmosphere and show that Hg starts to diffuse only above 653 K.

  16. Beam-profile monitor using a sodium-vapour

    CERN Multimedia

    1972-01-01

    Beam-profile monitor using a sodium-vapour curtain at 45 degrees to the ISR beam in Ring I (sodium generator is in white cylinder just left of centre). Electrons produced by ionization of the sodium vapour give an image of the beam on a fluorescent screen that is observed by a TV camera (at upper right).

  17. Photodegradation of petroleum under Na and Hg lamps by EPR

    Energy Technology Data Exchange (ETDEWEB)

    Mauro, Eduardo di; Melo, Fernando Alves de; Turini, Marilene; Campos, Ariana de [Universidade Estadual de Londrina (UEL), PR (Brazil). Dept. of Physics; Guedes, Carmen Luisa Barbosa [Universidade Estadual de Londrina (UEL), PR (Brazil). Dept. of Chemistry; Mangrich, Antonio Salvio [Universidade Federal do Parana (UFPR), PR (Brazil). Dept. of Chemistry

    2002-07-01

    Full text: The environment has become frequent victim of the action of pollutants. This situation has been stimulating several scientific works in the attempt to monitor the self-defence of the environment and minimise the effects caused by these pollutants. The petroleum and its derived, among the several substances that attack the environment, occupy a distinction place in the pollution picture. In the present work, we studied the photodegradation of the Arabian Light and Brazilian (Campos Basin- RJ) oils. Sample of theses oils were irradiated by different time periods in a reactor equipped with Na and Hg vapour lamps, whose emission spectra have different features. The irradiated and non-irradiated samples were subjected to Electron Paramagnetic Resonance (EPR) analysis in a BRUKER (ESP-300) equipment, which operates in the X band (9 GHz) at room temperature. The EPR spectra showed similar features to the two oils. The EPR spectra are composed of a intense signal (one line) with g (spectroscopic factor) about two relative to free radicals and groups of eight lines correspondent to vanadyl porphyrinic compounds (VO{sup 2+}). The parameters of spin Hamiltonian were determined to the two detected paramagnetic species. The two oils irradiated by Na and Hg lamps showed variations in the values of g and {delta}H (linewidth) of the paramagnetic species. The changes in the parameters are the most significant in Brazilian petroleum samples irradiated by Hg lamp. The modifications in the linewidth of free radicals of the Arabian Light petroleum have the same tendency to the two utilised lamps. (author)

  18. Effect of Water Vapour to Temperature Inside Sonoluminescing Bubble

    Institute of Scientific and Technical Information of China (English)

    安宇; 谢崇国; 应崇福

    2003-01-01

    Using the model based on the homo-pressure approximation, we explain why the maximum temperature is sensitive to the ambient temperature in the single bubble sonoluminescence. The numerical simulation shows that the maximum temperature inside a sonoluminescing bubble depends on how much water vapour evaporates or coagulates at the bubble wall during the bubble shrinking to its minimum size. While the amount of water vapour inside the bubble at the initial and the final state of the compression depends on the saturated water vapour pressure which is sensitive to the ambient temperature. The lower the saturated vapour pressure is, the higher the maximum temperature is. This may lead to more general conclusion that those liquids with lower saturated vapour pressure are more favourable for the single bubble sonoluminescence. We also compare those bubbles with different noble gases, the result shows that the maximum temperatures in the different gas bubbles are almost the same for those with the same ambient temperature.

  19. Stabilization of Leidenfrost vapour layer by textured superhydrophobic surfaces.

    Science.gov (United States)

    Vakarelski, Ivan U; Patankar, Neelesh A; Marston, Jeremy O; Chan, Derek Y C; Thoroddsen, Sigurdur T

    2012-09-13

    In 1756, Leidenfrost observed that water drops skittered on a sufficiently hot skillet, owing to levitation by an evaporative vapour film. Such films are stable only when the hot surface is above a critical temperature, and are a central phenomenon in boiling. In this so-called Leidenfrost regime, the low thermal conductivity of the vapour layer inhibits heat transfer between the hot surface and the liquid. When the temperature of the cooling surface drops below the critical temperature, the vapour film collapses and the system enters a nucleate-boiling regime, which can result in vapour explosions that are particularly detrimental in certain contexts, such as in nuclear power plants. The presence of these vapour films can also reduce liquid-solid drag. Here we show how vapour film collapse can be completely suppressed at textured superhydrophobic surfaces. At a smooth hydrophobic surface, the vapour film still collapses on cooling, albeit at a reduced critical temperature, and the system switches explosively to nucleate boiling. In contrast, at textured, superhydrophobic surfaces, the vapour layer gradually relaxes until the surface is completely cooled, without exhibiting a nucleate-boiling phase. This result demonstrates that topological texture on superhydrophobic materials is critical in stabilizing the vapour layer and thus in controlling--by heat transfer--the liquid-gas phase transition at hot surfaces. This concept can potentially be applied to control other phase transitions, such as ice or frost formation, and to the design of low-drag surfaces at which the vapour phase is stabilized in the grooves of textures without heating.

  20. Stabilization of Leidenfrost vapour layer by textured superhydrophobic surfaces

    KAUST Repository

    Vakarelski, Ivan Uriev

    2012-09-12

    In 1756, Leidenfrost observed that water drops skittered on a sufficiently hot skillet, owing to levitation by an evaporative vapour film. Such films are stable only when the hot surface is above a critical temperature, and are a central phenomenon in boiling. In this so-called Leidenfrost regime, the low thermal conductivity of the vapour layer inhibits heat transfer between the hot surface and the liquid. When the temperature of the cooling surface drops below the critical temperature, the vapour film collapses and the system enters a nucleate-boiling regime, which can result in vapour explosions that are particularly detrimental in certain contexts, such as in nuclear power plants. The presence of these vapour films can also reduce liquid-solid drag. Here we show how vapour film collapse can be completely suppressed at textured superhydrophobic surfaces. At a smooth hydrophobic surface, the vapour film still collapses on cooling, albeit at a reduced critical temperature, and the system switches explosively to nucleate boiling. In contrast, at textured, superhydrophobic surfaces, the vapour layer gradually relaxes until the surface is completely cooled, without exhibiting a nucleate-boiling phase. This result demonstrates that topological texture on superhydrophobic materials is critical in stabilizing the vapour layer and thus in controlling-by heat transfer-the liquid-gas phase transition at hot surfaces. This concept can potentially be applied to control other phase transitions, such as ice or frost formation, and to the design of low-drag surfaces at which the vapour phase is stabilized in the grooves of textures without heating. © 2012 Macmillan Publishers Limited. All rights reserved.

  1. The ignitability of petrol vapours and potential for vapour phase explosion by use of TASER® law enforcement electronic control device.

    Science.gov (United States)

    Clarke, C; Andrews, S P

    2014-12-01

    An experimental study was made of the potential of the TASER-X26™ law enforcement electronic control device to ignite petrol vapours if used by an officer to incapacitate a person soaked in petrol, or within a flammable atmosphere containing petrol vapour. Bench scale tests have shown that a wooden mannequin with pig skin covering the chest was a suitable representation of a human target. Full scale tests using the mannequin have shown that the arc from a TASER-X26™ is capable of igniting petrol/air vapours on a petrol-soaked person. Further tests in a 1/5 scale and a full scale compartment have shown that if a TASER is used within a compartment, a petrol vapour explosion (deflagration) may be achieved. It is evident from this research that if used in a flammable vapour rich environment, the device could prove fatal not only to the target but the TASER® operator as well.

  2. Chemical thermodynamics of the Hg1212 phase

    Science.gov (United States)

    Tsuchiya, Tetsuo; Fueki, Kazuo

    1997-02-01

    The single phase of Hg1212 was synthesized by the simple oxide method using starting materials containing HgO 16% in excess. Stability regions of Hg1212 and pure HgO were determined by measuring the decomposition temperature as a function of oxygen partial pressure, and thermodynamic diagrams showing the stability domains of HgO and Hg1212 were constructed. The thermodynamical condition of formation of Hg1212 was discussed using the diagrams. It was found by chemical analysis that the valence of Hg is always 2 + and the valence of Ce changes with the oxygen content. TC (zero) changed from 122 to 118 K when the oxygen content was increased from 6.10 to 6.22.

  3. The protective properties of thin alumina films deposited by metal organic chemical vapour deposition against high-temperature corrosion of stainless steels

    NARCIS (Netherlands)

    Morssinkhof, R.W.J.; Fransen, T.; Heusinkveld, M.M.D.; Gellings, P.J.

    1989-01-01

    Coatings of Al2O3 were deposited on Incoloy 800H and AISI 304 by means of metal organic chemical vapour deposition. Diffusion limitation was the rate-determining step above 420 °C. Below this temperature, the activation energy of the reaction appeared to be 30 kJ mol−1. Coating with Al2O3 increases

  4. Hydrothermal synthesis of alpha- and beta-HgS nanostructures

    Science.gov (United States)

    Galain, Isabel; María, Pérez Barthaburu; Ivana, Aguiar; Laura, Fornaro

    2017-01-01

    We synthesized HgS nanostructures by the hydrothermal method in order to use them as electron acceptors in hybrid organic-inorganic solar cells. We employed different mercury sources (HgO and Hg(CH3COO)2) and polyvinylpyrrolidone (PVP) or hexadecanethiol (HDT) as stabilizing/capping agent for controlling size, crystallinity, morphology and stability of the obtained nanostructures. We also used thiourea as sulfur source, and a temperature of 180 °C during 6 h. Synthesized nanostructures were characterized by powder X-Ray Diffraction, Diffuse Reflectance Infrared Fourier Transform and Transmission Electron Microscopy. When PVP acts as stabilizing agent, the mercury source has influence on the size -but not in morphology- of the beta-HgS obtained nansostructures. HDT has control over nanostructures' size and depending on the relation Hg:HDT, we obtained a mixture of alpha and beta HgS which can be advantageous in the application in solar cells, due their absorption in different spectral regions. The smallest nanostructures obtained have a mean diameter of 20 nm when using HDT as capping agent. Also, we deposited the aforementioned nanostructures onto flat glass substrates by the spin coating technique as a first approach of an active layer of a solar cell. The depositions were characterized by atomic force microscopy. We obtained smaller particle deposition and higher particle density -but a lower area coverage (5%) - in samples with HDT as capping agent. This work presents promising results on nanostructures for future application on hybrid solar cells. Further efforts will be focused on the deposition of organic-inorganic layers.

  5. Mercury Vapour Long-Lasting Exposure: Lymphocyte Muscarinic Receptors as Neurochemical Markers of Accidental Intoxication

    Directory of Open Access Journals (Sweden)

    E. Roda

    2016-01-01

    Full Text Available Introduction. Chronic poisoning may result in home setting after mercury (Hg vapours inhalation from damaged devices. We report a chronic, nonoccupational Hg poisoning due to 10-year indoor exposure to mercury spillage. Case Report. A 72-year-old man with polyneuropathy of suspected toxic origin. At hospitalization, toxicological clinical evaluations confirmed the altered neurological picture documented across the last decade. Periodic blood and urine Hg levels (BHg, UHg monitoring were performed from admission (t0, until 1 year later (t2, paralleled by blood neurochemical markers assessment, that is, lymphocytes muscarinic receptors (l-MRs. At t0: BHg and UHg were 27 and 1.4 microg/L, respectively (normal values: BHg 1–4.5; UHg 0.1–4.5, associated with l-MRs increase, 185.82 femtomoL/million lymphocytes (normal range: 8.0–16.0. At t1 (two days after DMSA-mobilization test, BHg weak reduction, paralleled by UHg 3.7-fold increase, was measured together with further l-MRs enhancement (205.43 femtomoL/million lymphocytes. At t2 (eight months after two cycles of DMSA chelating therapy ending, gradual improving of clinical manifestations was accompanied by progressive decrease of BHg and UHg (4.0 and 2.8 microg/L, resp. and peripheral l-MRs neurochemical marker (24.89 femtomoL/million lymphocytes. Conclusion. l-MRs modulatory effect supports their use as peripheral neurochemical marker in Hg poisoning diagnosis and chelation therapy monitoring.

  6. Mercury Vapour Long-Lasting Exposure: Lymphocyte Muscarinic Receptors as Neurochemical Markers of Accidental Intoxication

    Science.gov (United States)

    Roda, E.; Vecchio, S.; Apostoli, P.

    2016-01-01

    Introduction. Chronic poisoning may result in home setting after mercury (Hg) vapours inhalation from damaged devices. We report a chronic, nonoccupational Hg poisoning due to 10-year indoor exposure to mercury spillage. Case Report. A 72-year-old man with polyneuropathy of suspected toxic origin. At hospitalization, toxicological clinical evaluations confirmed the altered neurological picture documented across the last decade. Periodic blood and urine Hg levels (BHg, UHg) monitoring were performed from admission (t0), until 1 year later (t2), paralleled by blood neurochemical markers assessment, that is, lymphocytes muscarinic receptors (l-MRs). At t0: BHg and UHg were 27 and 1.4 microg/L, respectively (normal values: BHg 1–4.5; UHg 0.1–4.5), associated with l-MRs increase, 185.82 femtomoL/million lymphocytes (normal range: 8.0–16.0). At t1 (two days after DMSA-mobilization test), BHg weak reduction, paralleled by UHg 3.7-fold increase, was measured together with further l-MRs enhancement (205.43 femtomoL/million lymphocytes). At t2 (eight months after two cycles of DMSA chelating therapy ending), gradual improving of clinical manifestations was accompanied by progressive decrease of BHg and UHg (4.0 and 2.8 microg/L, resp.) and peripheral l-MRs neurochemical marker (24.89 femtomoL/million lymphocytes). Conclusion. l-MRs modulatory effect supports their use as peripheral neurochemical marker in Hg poisoning diagnosis and chelation therapy monitoring. PMID:27872646

  7. Water Vapour Radiometers for the Australia Telescope Compact Array

    CERN Document Server

    Indermuehle, Balthasar T; Crofts, Jonathan

    2012-01-01

    We have developed Water Vapour Radiometers (WVRs) for the Australia Telescope Compact Array (ATCA) that are capable of determining path fluctuations by virtue of measuring small temperature fluctuations in the atmosphere using the 22.2 GHz water vapour line for each of the six antennae. By measuring the line of sight variations of the water vapour, the induced path excess and thus the phase delay can be estimated and corrections can then be applied during data reduction. This reduces decorrelation of the source signal. We demonstrate how this recovers the telescope's efficiency and image quality as well as how this improves the telescope's ability to use longer baselines at higher frequencies, thereby resulting in higher spatial resolution. A description of the WVR hardware design, their calibration and water vapour retrieval mechanism is given.

  8. Probabilistic risk assessment for six vapour intrusion algorithms

    NARCIS (Netherlands)

    Provoost, J.; Reijnders, L.; Bronders, J.; Van Keer, I.; Govaerts, S.

    2014-01-01

    A probabilistic assessment with sensitivity analysis using Monte Carlo simulation for six vapour intrusion algorithms, used in various regulatory frameworks for contaminated land management, is presented here. In addition a deterministic approach with default parameter sets is evaluated against obse

  9. Probabilistic risk assessment for six vapour intrusion algorithms

    NARCIS (Netherlands)

    Provoost, J.; Reijnders, L.; Bronders, J.; Van Keer, I.; Govaerts, S.

    2014-01-01

    A probabilistic assessment with sensitivity analysis using Monte Carlo simulation for six vapour intrusion algorithms, used in various regulatory frameworks for contaminated land management, is presented here. In addition a deterministic approach with default parameter sets is evaluated against

  10. Probabilistic risk assessment for six vapour intrusion algorithms

    NARCIS (Netherlands)

    Provoost, J.; Reijnders, L.; Bronders, J.; Van Keer, I.; Govaerts, S.

    2014-01-01

    A probabilistic assessment with sensitivity analysis using Monte Carlo simulation for six vapour intrusion algorithms, used in various regulatory frameworks for contaminated land management, is presented here. In addition a deterministic approach with default parameter sets is evaluated against obse

  11. Analysis of IMP-grown Cd sub x Hg sub 1-x Te using helium ion RBS

    Energy Technology Data Exchange (ETDEWEB)

    Avery, A.J.; Diskett, D.J. (Royal Military Coll. of Science, Shrivenham, Swindon (United Kingdom)); Gough, J.S.; Young, M.L. (Royal Signals and Radar Establishment, Malvern (United Kingdom))

    1992-02-01

    Epitaxial layers of Cd{sub x}Hg{sub 1-x}Te may be grown by the IMP (interdiffused multilayer process) technique in which alternate layers of CdTe and HgTe are deposited by metalorganic vapour phase epitaxy and interdiffused at the growth temperature. The infrared optical properties of the layers are critically dependent upon the value of x which may be tailored by controlling the relative thickness of the CdTe and HgTe sublayers. This paper describes the application of helium ion RBS to the study of the completeness of interdiffusion between sublayers and the application of channelling to the study of their crystalline quality. (orig.).

  12. Landmine Detection Technologies to TraceExplosive Vapour Detection Techniques

    OpenAIRE

    2007-01-01

    Large quantity of explosive is manufactured worldwide for use in various types of ammunition,arms, and mines, and used in armed conflicts. During manufacturing and usage of the explosiveequipment, some of the explosive residues are released into the environment in the form ofcontaminated effluents, unburnt explosives fumes and vapours. Limited but uncontrolledcontinuous release of trace vapours also takes place when explosive-laden landmines are deployedin the field. One of the major technolo...

  13. Stand-off detection of alcohol vapours in moving cars

    Science.gov (United States)

    Kopczyński, Krzysztof; Kubicki, Jan; Młyńczak, Jaroslaw; Mierczyk, Jadwiga; Hackiewicz, Klaudia

    2016-12-01

    In this article we present the research on optoelectronic system for stand-off detection of alcohol vapours in moving cars. The idea of using commercially available cascade lasers was presented. Special attention was paid to the optical characteristics of the car windowpanes. It was shown that using 3.45 μm and 3.59 μm wavelengths the alcohol vapours inside a car can be successfully detected even for cars with different windows

  14. An apparatus for determining water vapour permeability of fabrics

    Directory of Open Access Journals (Sweden)

    B. L. Saksena

    1955-04-01

    Full Text Available An apparatus for the determination of water vapour permeability (W.V.P. of fabrics is described. The fabric partitions a closed space into two compartments in which are circulated air streams having high and low water vapour pressure respectively, without any overall pressure or temperature difference. The transfer of moisture from the high to the low humidity side of the fabric is gravimetrically measured. Results of tests are given.

  15. On-line speciation of inorganic and methyl mercury in waters and fish tissues using polyaniline micro-column and flow injection-chemical vapour generation-inductively coupled plasma mass spectrometry (FI-CVG-ICPMS).

    Science.gov (United States)

    Krishna, M V Balarama; Chandrasekaran, K; Karunasagar, D

    2010-04-15

    A simple and efficient method for the determination of ultra-trace amounts of inorganic mercury (iHg) and methylmercury (MeHg) in waters and fish tissues was developed using a micro-column filled with polyaniline (PANI) coupled online to flow injection-chemical vapour generation-inductively coupled plasma mass spectrometry (FI-CVG-ICPMS) system. Preliminary studies indicated that inorganic and methyl mercury species could be separated on PANI column in two different speciation approaches. At pH extraction of the mercury species from biological samples, was used directly to separate MeHg from iHg in the fish tissues (tuna fish ERM-CE 463, ERM-CE 464 and IAEA-350) by PANI column using speciation procedure 1. The determined values were in good agreement with certified values. Under optimal conditions, the limits of detection (LODs) were 2.52 pg and 3.24 pg for iHg and MeHg (as Hg) respectively. The developed method was applied successfully to the direct determination of iHg and MeHg in various waters (tap water, lake water, ground water and sea-water) and the recoveries for the spiked samples were in the range of 96-102% for both the Hg species.

  16. Naphthalene contamination of sterilized milk drinks contained in low-density polyethylene bottles. Part 2. Effect of naphthalene vapour in air.

    Science.gov (United States)

    Lau, O W; Wong, S K; Leung, K S

    1995-04-01

    A survey on naphthalene vapour in air was conducted, revealing that the ambient atmosphere contained concentrations of naphthalene in the range of 0.005-0.100 mg m-3. The level of naphthalene vapour in air increased to 0.35 and 4.00 mg m-3 in places exposed to lacquer paint and naphthalene-based moth-repellent, respectively. The effect of naphthalene vapour in air on milk drinks contained in low-density polyethylene (LDPE) bottles was assessed. A mathematical model was suggested to describe the migration of naphthalene from the atmosphere into milk. The model was proved to be valid for milk drinks exposed to naphthalene-based moth-repellent during storage. Moreover, the extent of migration was found to increase with the fat content of foods, which might be ascribed to an increase in diffusion, in addition to the kinetic factor, that affects naphthalene migration.

  17. A new approach to the water vapour feedback

    Science.gov (United States)

    Ingram, W.

    2012-12-01

    Climate sensitivity is often said to be doubled by water vapour feedback. From simple physical arguments, confirmed by GCMs, and consistent with the limited observational evidence, we expect the distribution of RH to change little under climate change. This implies a substantial positive feedback on climate change - but why about a doubling? And why is this value so robust even to major modelling errors and approximations? And why do GCMs never give a run-away water vapour greenhouse effect, plausible though extrapolation can make it seem? Considering the "paradox" of Simpson (1928) leads to a simple model that explains all these. The "partly-Simpsonian" model for the water vapour feedback on climate change implies a very simple constraint - that the component of OLR radiated by water vapour does not change as climate changes, while that radiated by everything else (surface, clouds, CO2, etc.) increases following Planck's Law. This does not predict the actual non-cloud LW response λCSLW of GCMs quantitatively accurately, but gives the general size. It also explains why a run-away water vapour greenhouse effect is not possible in Earth-like conditions: the partly-Simpsonian water vapour feedback can do no more than cancel part of the basic Planck's-Law negative feedback - less than 100% as long as some OLR is not from water vapour. The robustness of the GCMs' water vapour feedbacks, even if they simulate the water vapour distribution very badly, also follows: the fraction of emission by water vapour is both innately computationally robust (even large errors in water vapour amounts can only affect those limited parts of the spectrum of intermediate optical depth: most of the spectrum will be effectively opaque or effectively transparent at any given location), and closely related to the surface downward LW flux, which is verifiable and tunable. In addition, the partly-Simpsonian model provides a physical explanation for the long-known fact that LW radiances or OLR

  18. Hg transfer from contaminated soils to plants and animals

    NARCIS (Netherlands)

    Rodrigues, S.M.; Henriques, B.; Reis, A.T.; Duarte, A.C.; Pereira, E.; Romkens, P.F.A.M.

    2012-01-01

    Understanding the transfer of mercury (Hg) from soil to crops is crucial due to Hg toxicity and Hg occurrence in terrestrial systems. Previous research has shown that available Hg in soils contributes to plant Hg levels. Plant Hg concentrations are related to soil conditions and plant characteristic

  19. Microbial Oxidation of Hg(0) - Its Effect on Hg Stable Isotope Fractionation and Methylmercury Production

    Energy Technology Data Exchange (ETDEWEB)

    Yee, Nathan [Rutgers Univ., New Brunswick, NJ (United States); Barkay, Tamar [Rutgers Univ., New Brunswick, NJ (United States); Reinfelder, John [Rutgers Univ., New Brunswick, NJ (United States)

    2016-06-28

    Mercury (Hg) associated with mixed waste generated by nuclear weapons manufacturing has contaminated vast areas of the Oak Ridge Reservation (ORR). Neurotoxic methylmercury (MeHg) has been formed from the inorganic Hg wastes discharged into headwaters of East Fork Poplar Creek (EFPC). Thus, understanding the processes and mechanisms that lead to Hg methylation along the flow path of EFPC is critical to predicting the impacts of the contamination and the design of remedial action at the ORR. In part I of our project, we investigated Hg(0) oxidation and methylation by anaerobic bacteria. We discovered that the anaerobic bacterium Desulfovibrio desulfuricans ND132 can oxidize elemental mercury [Hg(0)]. When provided with dissolved elemental mercury, D. desulfuricans ND132 converts Hg(0) to Hg(II) and neurotoxic methylmercury [MeHg]. We also demonstrated that diverse species of subsurface bacteria oxidizes dissolved elemental mercury under anoxic conditions. The obligate anaerobic bacterium Geothrix fermentans H5, and the facultative anaerobic bacteria Shewanella oneidensis MR-1 and Cupriavidus metallidurans AE104 can oxidize Hg(0) to Hg(II) under anaerobic conditions. In part II of our project, we established anaerobic enrichment cultures and obtained new bacterial strains from the DOE Oak Ridge site. We isolated three new bacterial strains from subsurface sediments collected from Oak Ridge. These isolates are Bradyrhizobium sp. strain FRC01, Clostridium sp. strain FGH, and a novel Negativicutes strain RU4. Strain RU4 is a completely new genus and species of bacteria. We also demonstrated that syntrophic interactions between fermentative bacteria and sulfate-reducing bacteria in Oak Ridge saprolite mediate iron reduction via multiple mechanisms. Finally, we tested the impact of Hg on denitrification in nitrate reducing enrichment cultures derived from subsurface sediments from the Oak Ridge site, where nitrate is a major contaminant. We showed that there is an inverse

  20. Microbial Oxidation of Hg(0) - Its Effect on Hg Stable Isotope Fractionation and Methylmercury Production

    Energy Technology Data Exchange (ETDEWEB)

    Yee, Nathan [Rutgers Univ., New Brunswick, NJ (United States); Barkay, Tamar [Rutgers Univ., New Brunswick, NJ (United States); Reinfelder, John [Rutgers Univ., New Brunswick, NJ (United States)

    2016-06-28

    Mercury (Hg) associated with mixed waste generated by nuclear weapons manufacturing has contaminated vast areas of the Oak Ridge Reservation (ORR). Neurotoxic methylmercury (MeHg) has been formed from the inorganic Hg wastes discharged into headwaters of East Fork Poplar Creek (EFPC). Thus, understanding the processes and mechanisms that lead to Hg methylation along the flow path of EFPC is critical to predicting the impacts of the contamination and the design of remedial action at the ORR. In part I of our project, we investigated Hg(0) oxidation and methylation by anaerobic bacteria. We discovered that the anaerobic bacterium Desulfovibrio desulfuricans ND132 can oxidize elemental mercury [Hg(0)]. When provided with dissolved elemental mercury, D. desulfuricans ND132 converts Hg(0) to Hg(II) and neurotoxic methylmercury [MeHg]. We also demonstrated that diverse species of subsurface bacteria oxidizes dissolved elemental mercury under anoxic conditions. The obligate anaerobic bacterium Geothrix fermentans H5, and the facultative anaerobic bacteria Shewanella oneidensis MR-1 and Cupriavidus metallidurans AE104 can oxidize Hg(0) to Hg(II) under anaerobic conditions. In part II of our project, we established anaerobic enrichment cultures and obtained new bacterial strains from the DOE Oak Ridge site. We isolated three new bacterial strains from subsurface sediments collected from Oak Ridge. These isolates are Bradyrhizobium sp. strain FRC01, Clostridium sp. strain FGH, and a novel Negativicutes strain RU4. Strain RU4 is a completely new genus and species of bacteria. We also demonstrated that syntrophic interactions between fermentative bacteria and sulfate-reducing bacteria in Oak Ridge saprolite mediate iron reduction via multiple mechanisms. Finally, we tested the impact of Hg on denitrification in nitrate reducing enrichment cultures derived from subsurface sediments from the Oak Ridge site, where nitrate is a major contaminant. We showed that there is an inverse

  1. Nanofluidic transport governed by the liquid/vapour interface.

    Science.gov (United States)

    Lee, Jongho; Laoui, Tahar; Karnik, Rohit

    2014-04-01

    Liquid/vapour interfaces govern the behaviour of a wide range of systems but remain poorly understood, leaving ample margin for the exploitation of intriguing functionalities for applications. Here, we systematically investigate the role of liquid/vapour interfaces in the transport of water across apposing liquid menisci in osmosis membranes comprising short hydrophobic nanopores that separate two fluid reservoirs. We show experimentally that mass transport is limited by molecular reflection from the liquid/vapour interface below a certain length scale, which depends on the transmission probability of water molecules across the nanopores and on the condensation probability of a water molecule incident on the liquid surface. This fundamental yet elusive condensation property of water is measured under near-equilibrium conditions and found to decrease from 0.36 ± 0.21 at 30 °C to 0.18 ± 0.09 at 60 °C. These findings define the regime in which liquid/vapour interfaces govern nanofluidic transport and have implications for understanding mass transport in nanofluidic devices, droplets and bubbles, biological components and porous media involving liquid/vapour interfaces.

  2. Can painted glass felt or glass fibre cloth be used as vapour barrier?

    DEFF Research Database (Denmark)

    El-Khattam, Amira; Andersen, Mie Them; Hansen, Kurt Kielsgaard

    2014-01-01

    it is essential to know how much influence a surface treatment has on the water vapour transport. Traditionally, there has been most focus on paints that affect the permeability as little as possible. However, sometimes water vapour resistance is desirable. Especially, this is relevant in existing buildings...... with a ventilated attic where the ceiling may be air tight but has no vapour barrier; post-insulation of the attic may cause the need for a vapour barrier. Placing a vapour barrier above the ceiling can be tiresome and it is difficult to ensure tightness. A simpler way is to paint a vapour barrier directly...

  3. Effects of copper vapour on thermophysical properties of CO2-N2 plasma

    Science.gov (United States)

    Zhong, Linlin; Wang, Xiaohua; Rong, Mingzhe; Cressault, Yann

    2016-10-01

    CO2-N2 mixtures are often used as arc quenching medium (to replace SF6) in circuit breakers and shielding gas in arc welding. In such applications, copper vapour resulting from electrode surfaces can modify characteristics of plasmas. This paper therefore presents an investigation of the effects of copper on thermophysical properties of CO2-N2 plasma. The equilibrium compositions, thermodynamic properties (including mass density, specific enthalpy, and specific heat), transport coefficients (including electrical conductivity, viscosity, and thermal conductivity), and four kinds of combined diffusion coefficients due to composition gradients, applied electric fields, temperature gradients, and pressure gradients respectively, were calculated and discussed for CO2-N2 (mixing ratio 7:3) plasma contaminated by different proportions of copper vapour. The significant influences of copper were observed on all the properties of CO2-N2-Cu mixtures. The better ionization ability and larger molar mass of copper and larger collision integrals related to copper, should be responsible for such influences.

  4. Landmine Detection Technologies to TraceExplosive Vapour Detection Techniques

    Directory of Open Access Journals (Sweden)

    J. C. Kapoor

    2007-11-01

    Full Text Available Large quantity of explosive is manufactured worldwide for use in various types of ammunition,arms, and mines, and used in armed conflicts. During manufacturing and usage of the explosiveequipment, some of the explosive residues are released into the environment in the form ofcontaminated effluents, unburnt explosives fumes and vapours. Limited but uncontrolledcontinuous release of trace vapours also takes place when explosive-laden landmines are deployedin the field. One of the major technological challenges in post-war scenario worldwide is thedetection of landmines using these trace vapour signatures and neutralising them safely.  Differenttypes of explosives are utilised as the main charge in antipersonnel and antitank landmines. Inthis paper, an effort has been made to review the techniques so far available based on explosivevapour detection especially to detect the landmines. A comprehensive compilation of relevantinformation on the techniques is presented, and their maturity levels, shortcomings, and difficultiesfaced are highlighted.

  5. Single mode quadrature entangled light from room temperature atomic vapour

    CERN Document Server

    Wasilewski, W; Jensen, K; Madsen, L S; Krauter, H; Polzik, E S

    2009-01-01

    We analyse a novel squeezing and entangling mechanism which is due to correlated Stokes and anti-Stokes photon forward scattering in a multi-level atom vapour. Following the proposal we present an experimental demonstration of 3.5 dB pulsed frequency nondegenerate squeezed (quadrature entangled) state of light using room temperature caesium vapour. The source is very robust and requires only a few milliwatts of laser power. The squeezed state is generated in the same spatial mode as the local oscillator and in a single temporal mode. The two entangled modes are separated by twice the Zeeman frequency of the vapour which can be widely tuned. The narrow-band squeezed light generated near an atomic resonance can be directly used for atom-based quantum information protocols. Its single temporal mode characteristics make it a promising resource for quantum information processing.

  6. Simultaneous negative permittivity and permeability in a coherent atomic vapour

    Institute of Scientific and Technical Information of China (English)

    Shen Jian-Qi

    2007-01-01

    A new quantum optical mechanism to realize simultaneously negative electric permittivity and magnetic permeability is suggested. In order to obtain a negative permeability, we choose a proper atomic configuration that can dramatically enhance the contribution of the magnetic-dipole allowed transition via the atomic phase coherence. It is shown that the atomic system chosen with proper optical parameters can give rise to striking electromagnetic responses (leading to a negative refractive index) and that the atomic vapour becomes a left-handed medium in an optical frequency band. Differing from the previous schemes of artificial composite metamaterials (based on classical electromagnetic theory) to achieve the left-handed materials, which consist of anisotropic millimetre-scale composite structure units, the left-handed atomic vapour presented here is isotropic and homogeneous at the atomic-scale level. Such an advantage may be valuable in realizing the superlens (and hence perfect image) with left-handed atomic vapour.

  7. MBE Growth and Transfer of HgCdTe Epitaxial Films from InSb Substrates

    Science.gov (United States)

    de Lyon, T. J.; Rajavel, R. D.; Nosho, B. Z.; Terterian, S.; Beliciu, M. L.; Patterson, P. R.; Chang, D. T.; Boag-O'Brien, M. F.; Holden, B. T.; Jacobs, R. N.; Benson, J. D.

    2010-07-01

    An investigation of the heteroepitaxial growth of HgCdTe films onto InSb(211)B substrates is reported. High-quality HgCdTe(211)B single-crystal films have been successfully deposited onto InSb(211)B substrates and have been characterized with x-ray diffraction rocking curve analysis, etch pit density analysis, and surface void defect mapping. X-ray rocking curve (422) reflection full-width at half-maximum of 60 arcsec has been obtained for 7- μm-thick x = 0.22 HgCdTe epitaxial films, and etch pit densities of 3 × 106 cm-2 to 3 × 107 cm-2 have been observed. A significant reduction in HgCdTe void defect densities to 100 cm-2 to 200 cm-2 has been observed on InSb, including a complete absence of large “void cluster” defects that are often observed for growth on CdZnTe. Wafer bow induced by the growth of HgCdTe on InSb is less than 1 μm for 2-inch-diameter substrates. Significant diffusion of In into HgCdTe is observed for HgCdTe/InSb wafers that are subjected to Hg anneals at 250°C to 300°C. A preliminary investigation of the transfer of HgCdTe films from InSb onto Si substrates has also been undertaken, using an adhesive wafer bonding approach evaluated with scanning acoustic microscopy. The infrared transmission characteristics of the bonding adhesive have been investigated with respect to postgrowth annealing procedures to establish the compatibility of the bonding approach with HgCdTe device processing and detector operation.

  8. Intercomparison of TCCON and MUSICA Water Vapour Products

    Science.gov (United States)

    Weaver, D.; Strong, K.; Deutscher, N. M.; Schneider, M.; Blumenstock, T.; Robinson, J.; Notholt, J.; Sherlock, V.; Griffith, D. W. T.; Barthlott, S.; García, O. E.; Smale, D.; Palm, M.; Jones, N. B.; Hase, F.; Kivi, R.; Ramos, Y. G.; Yoshimura, K.; Sepúlveda, E.; Gómez-Peláez, Á. J.; Gisi, M.; Kohlhepp, R.; Warneke, T.; Dohe, S.; Wiegele, A.; Christner, E.; Lejeune, B.; Demoulin, P.

    2014-12-01

    We present an intercomparison between the water vapour products from the Total Carbon Column Observing Network (TCCON) and the MUlti-platform remote Sensing of Isotopologues for investigating the Cycle of Atmospheric water (MUSICA), two datasets from ground-based Fourier Transform InfraRed (FTIR) spectrometers with good global representation. Where possible, comparisons to radiosondes are also included. The near-infrared TCCON measurements are optimized to provide precise monitoring of greenhouse gases for carbon cycle studies; however, TCCON's retrievals also produce water vapour products. The mid-infrared MUSICA products result from retrievals optimized to give precise and accurate information about H2O, HDO, and δD. The MUSICA water vapour products have been validated by extensive intercomparisons with H2O and δD in-situ measurements made from ground, radiosonde, and aircraft (Schneider et al. 2012, 2014), as well as by intercomparisons with satellite-based H2O and δD remote sensing measurements (Wiegele et al., 2014). This dataset provides a valuable reference point for other measurements of water vapour. This study is motivated by the limited intercomparisons performed for TCCON water vapour products and limited characterisation of their uncertainties. We compare MUSICA and TCCON products to assess the potential for TCCON measurements to contribute to studies of the water cycle, water vapour's role in climate and use as a tracer for atmospheric dynamics, and to evaluate the performance of climate models. The TCCON and MUSICA products result from measurements taken using the same FTIR instruments, enabling a comparison with constant instrumentation. The retrieval techniques differ, however, in their method and a priori information. We assess the impact of these differences and characterize the comparability of the TCCON and MUSICA datasets.

  9. Validation of SCIAMACHY AMC-DOAS water vapour columns

    Directory of Open Access Journals (Sweden)

    S. Noël

    2005-04-01

    Full Text Available A first validation of water vapour total column amounts derived from measurements of the SCanning Imaging Absorption spectroMeter for Atmospheric CHartographY (SCIAMACHY in the visible spectral region has been performed. For this purpose, SCIAMACHY water vapour data have been determined for the year 2003 using an extended version of the Differential Optical Absorption Spectroscopy (DOAS method, called Air Mass Corrected (AMC-DOAS. The SCIAMACHY results are compared with corresponding water vapour measurements by the Special Sensor Microwave Imager (SSM/I and with model data from the European Centre for Medium-Range Weather Forecasts (ECMWF.

    In confirmation of previous results it could be shown that SCIAMACHY derived water vapour columns are typically slightly lower than both SSM/I and ECMWF data, especially over ocean areas. However, these deviations are much smaller than the observed scatter of the data which is caused by the different temporal and spatial sampling and resolution of the data sets. For example, the overall difference with ECMWF data is only −0.05 g/cm2 whereas the typical scatter is in the order of 0.5 g/cm2. Both values show almost no variation over the year.

    In addition, first monthly means of SCIAMACHY water vapour data have been computed. The quality of these monthly means is currently limited by the availability of calibrated SCIAMACHY spectra. Nevertheless, first comparisons with ECMWF data show that SCIAMACHY (and similar instruments are able to provide a new independent global water vapour data set.

  10. A Discharge-Excited SrBr2 Vapour Laser

    Institute of Scientific and Technical Information of China (English)

    潘佰良; 姚志欣; 陈钢

    2002-01-01

    A new-style discharge tube for a metal vapour laser has been designed and built. SrBr2 was successfullyused to replace the metal strontium as a working medium. Multi-line laser oscillations from resonance tometastable transition of strontium atoms (6.45um), ions (1.03um/1.O9um) and from strontium ion recombi-nation (416.2nm/430.5nm) have been obtained through longitudinal pulsed discharge. The problem of an in-compatibility reaction between metallic strontium and the discharge tube in the strontium vapour laser has beensolved. Some proposals are presented for further developments of strontium halide lasers.

  11. Spontaneous and parametric processes in warm rubidium vapours

    CERN Document Server

    Dąbrowski, Michał; Pęcak, Daniel; Chrapkiewicz, Radosław; Wasilewski, Wojciech

    2014-01-01

    Warm rubidium vapours are known to be a versatile medium for a variety of experiments in atomic physics and quantum optics. Here we present experimental results on producing the frequency converted light for quantum applications based on spontaneous and stimulated processes in rubidium vapours. In particular, we study the efficiency of spontaneously initiated stimulated Raman scattering in the {\\Lambda}-level configuration and conditions of generating the coherent blue light assisted by multi-photon transitions in the diamond-level configuration. Our results will be helpful in search for new types of interfaces between light and atomic quantum memories.

  12. Spontaneuos and Parametric Processes in Warm Rubidium Vapours

    Directory of Open Access Journals (Sweden)

    Dąbrowski M.

    2014-12-01

    Full Text Available Warm rubidium vapours are known to be a versatile medium for a variety of experiments in atomic physics and quantum optics. Here we present experimental results on producing the frequency converted light for quantum applications based on spontaneous and stimulated processes in rubidium vapours. In particular, we study the efficiency of spontaneously initiated stimulated Raman scattering in the Λ-level configuration and conditions of generating the coherent blue light assisted by multi-photon transitions in the diamond-level configuration. Our results will be helpful in search for new types of interfaces between light and atomic quantum memories.

  13. Phytochelatin synthesis in response to Hg uptake in aquatic plants near a chlor-alkali factory.

    Science.gov (United States)

    Turull, Marta; Grmanova, Gabriela; Dago, Àngela; Ariño, Cristina; Díez, Sergi; Díaz-Cruz, José Manuel; Esteban, Miquel

    2017-06-01

    The effects of mercury (Hg) released from a chlor-alkali factory in aquatic plants along the Ebro River basin (NE Spain) were analysed considering the phytochelatins (PCn) and their isoforms content in these plants. These compounds were analyzed using HPLC with amperometric detection, and the macrophytes species Ceratophyllum demersum and Myriopyllum spicatum were collected in two sampling campaigns, autumn and spring, respectively. To correlate the PCn content in macrophytes with the Hg contamination, analysis of total Hg (THg) content in plants and suspended particulate matter, as well as the dissolved-bioavailable fraction of Hg in water measured by the diffusive gradient in thin film (DGT) technique were done. The results confirm the presence of PC2-Ala in extracts of C. demersum and PC2-desGly in M. spicatum, and the concentration of these thiol compounds depends clearly on the distance between the hot spot and the downstream sites: the higher the levels are, the closer the hot spot is. Since most of the Hg is hypothesized to be associated with SPM and transported downstream, our results of the DGT suggest that trace amounts of Hg in water can be released as free metal ions yielding a certain accumulation in plants (reaching the ppb level) that are enough for activation of induction of PCs. A few PCs species have been determined, at different seasons, indicating that they can be used as good indicators of the presence of bioavailable Hg in aquatic media throughout the year.

  14. Comparison of Hexane Vapour Permeation in Two Different Polymeric Membranes via an Innovative In-line FID Detection Method

    Directory of Open Access Journals (Sweden)

    Z. Petrusová

    2017-07-01

    Full Text Available This manuscript presents a novel method for the analysis of vapour permeation through polymeric membranes based on in-line analysis of the permeate with an FID detector. The hexane vapour permeation was studied for two commercially available membranes, namely low-density polyethylene (LDPE and thin-film-composite polyamide (PA membrane. The hexane permeation was studied at temperatures of 25–45 °C, hexane vapour activity in the range of 0.2–0.8 and trans-membrane pressures of 5–50 kPa. Two fundamentally different membranes were chosen to demonstrate the potential and sensitivity of the permeation apparatus. Upon increasing the temperature from 25 to 45 °C, the flux in LDPE was found to increase almost fourfold over the whole activity range. The nonlinear increase of the flux with activity indicates plasticization of the polymer by hexane. Contrarily, the flux in the PA membrane increases almost linearly with activity, with only a minor upward curvature. Since the PA is far away from any phase transition, it is less temperature-dependent than LDPE. The activation energy for permeation demonstrates that the temperature dependence in the LDPE membrane is dominated by changes in diffusion, whereas it is dominated by changes in solubility in the PA membrane.

  15. A mechanical-force-driven physical vapour deposition approach to fabricating complex hydride nanostructures

    Science.gov (United States)

    Pang, Yuepeng; Liu, Yongfeng; Gao, Mingxia; Ouyang, Liuzhang; Liu, Jiangwen; Wang, Hui; Zhu, Min; Pan, Hongge

    2014-03-01

    Nanoscale hydrides desorb and absorb hydrogen at faster rates and lower temperatures than bulk hydrides because of their high surface areas, abundant grain boundaries and short diffusion distances. No current methods exist for the direct fabrication of nanoscale complex hydrides (for example, alanates, borohydrides) with unique morphologies because of their extremely high reducibility, relatively low thermodynamic stability and complicated elemental composition. Here, we demonstrate a mechanical-force-driven physical vapour deposition procedure for preparing nanoscale complex hydrides without scaffolds or supports. Magnesium alanate nanorods measuring 20-40 nm in diameter and lithium borohydride nanobelts measuring 10-40 nm in width are successfully synthesised on the basis of the one-dimensional structure of the corresponding organic coordination polymers. The dehydrogenation kinetics of the magnesium alanate nanorods are improved, and the nanorod morphology persists through the dehydrogenation-hydrogenation process. Our findings may facilitate the fabrication of such hydrides with improved hydrogen storage properties for practical applications.

  16. The speed of sound in a gas-vapour bubbly liquid.

    Science.gov (United States)

    Prosperetti, Andrea

    2015-10-01

    In addition to the vapour of the liquid, bubbles in cavitating flows usually contain also a certain amount of permanent gas that diffuses out of the liquid as they grow. This paper presents a simplified linear model for the propagation of monochromatic pressure waves in a bubbly liquid with these characteristics. Phase change effects are included in detail, while the gas is assumed to follow a polytropic law. It is shown that even a small amount of permanent gas can have a major effect on the behaviour of the system. Particular attention is paid to the low-frequency range, which is of special concern in flow cavitation. Numerical results for water and liquid oxygen illustrate the implications of the model.

  17. Can painted glass felt or glass fibre cloth be used as vapour barrier?

    DEFF Research Database (Denmark)

    El-Khattam, Amira; Andersen, Mie Them; Hansen, Kurt Kielsgaard

    2014-01-01

    it is essential to know how much influence a surface treatment has on the water vapour transport. Traditionally, there has been most focus on paints that affect the permeability as little as possible. However, sometimes water vapour resistance is desirable. Especially, this is relevant in existing buildings...... with a ventilated attic where the ceiling may be air tight but has no vapour barrier; post-insulation of the attic may cause the need for a vapour barrier. Placing a vapour barrier above the ceiling can be tiresome and it is difficult to ensure tightness. A simpler way is to paint a vapour barrier directly...... on the ceiling e.g. as an ordinary paint. This paper presents the results of an investigation of the water vapour resistance of surface treatments which are commonly used in-door. The water vapour resistance was measured by the cup method. Aerated concrete was investigated with and without various surface...

  18. Simulation of Satellite Water Vapour Lidar Measurements: Performance Assessment under Real Atmospheric Conditions.

    OpenAIRE

    Di Girolamo, Paolo; Behrendt, Andreas; Kiemle, Christoph; Wulfmeyer, Volker; Bauer, Heinz; Summa, Donato; Dörnbrack, Andreas; Ehret, Gerhard

    2008-01-01

    A lidar simulator has been applied to assess the performances of a satellite water vapour differential absorption lidar (DIAL) system. Measurements performed by the airborne Deutsches Zentrum für Luft- und Raumfahrt (DLR) water vapour DIAL on 15 May 2002 during ESA’s Water Vapour Lidar Experiment (WALEX), in combination with MM5 mesoscale model output, were used to obtain backscatter and water vapour fields with high resolution and accuracy. These data and model output serve as input for the ...

  19. Emission Spectra of Working Mixtures of a HgBr/HgCl Excimer Lamp

    Science.gov (United States)

    Malinin, A. N.; Guĭvan, N. N.; Shimon, L. L.

    2000-12-01

    A study of emission spectra of a gas-discharge plasma produced in a HgBr/HgCl excimer lamp, which is filled with multicomponent working mixtures at atmospheric pressure (HgBr2 and HgCl2 with additions of molecular nitrogen and xenon), are reported. A gas-discharge plasma was produced by high-frequency (pulses ˜100 ns long with a repetition rate of up to 2000 Hz) barrier and surface discharges, which took place simultaneously. Emission of HgBr* and HgCl* excimer molecules, the second positive system of molecular oxygen, and helium and xenon lines in the UV, visible, and IR spectral regions was observed. The strongest emission of HgBr* and HgCl* molecules (the emission intensities were in the ratio 10:1) was observed in the HgBr2: HgCl2: N2: He mixture. Regularities in spectral and integrated characteristics of gas-discharge plasma emission are discussed.

  20. HgTe-CdTe SUPERLATTICES

    OpenAIRE

    Smith, D; Mcgill, T.

    1984-01-01

    We report on a theoretical study of the electronic properties of HgTe-CdTe superlattices. The band gap as a function of layer thickness, effective masses normal to the layer plane and tunneling length are compared to the corresponding (Hg, Cd)Te alloys. We find that the superlattice possesses a number of properties that may make it superior to the corresponding alloy as an infrared material.

  1. Impact of major volcanic eruptions on stratospheric water vapour

    Science.gov (United States)

    Löffler, Michael; Brinkop, Sabine; Jöckel, Patrick

    2016-05-01

    Volcanic eruptions can have a significant impact on the Earth's weather and climate system. Besides the subsequent tropospheric changes, the stratosphere is also influenced by large eruptions. Here changes in stratospheric water vapour after the two major volcanic eruptions of El Chichón in Mexico in 1982 and Mount Pinatubo on the Philippines in 1991 are investigated with chemistry-climate model simulations. This study is based on two simulations with specified dynamics of the European Centre for Medium-Range Weather Forecasts Hamburg - Modular Earth Submodel System (ECHAM/MESSy) Atmospheric Chemistry (EMAC) model, performed within the Earth System Chemistry integrated Modelling (ESCiMo) project, of which only one includes the long-wave volcanic forcing through prescribed aerosol optical properties. The results show a significant increase in stratospheric water vapour induced by the eruptions, resulting from increased heating rates and the subsequent changes in stratospheric and tropopause temperatures in the tropics. The tropical vertical advection and the South Asian summer monsoon are identified as sources for the additional water vapour in the stratosphere. Additionally, volcanic influences on tropospheric water vapour and El Niño-Southern Oscillation (ENSO) are evident, if the long-wave forcing is strong enough. Our results are corroborated by additional sensitivity simulations of the Mount Pinatubo period with reduced nudging and reduced volcanic aerosol extinction.

  2. Surface Electrical Conductivity of Single Crystal Spinel in Cesium Vapour.

    Science.gov (United States)

    2007-11-02

    magnesium aluminate spinel at temperatures ranging from 573K to 923K, in the presence of cesium vapour at pressures up to 1Torr. The interest in spinel has...in the core of a nuclear reactor. In contrast to magnesium oxide and alumina, electron irradiation of spinel produces no dislocation structures

  3. Water vapour and carbon dioxide decrease nitric oxide readings

    NARCIS (Netherlands)

    vanderMark, TW; Kort, E; Meijer, RJ; Postma, DS; Koeter, GH

    Measurement of nitric oxide levels in exhaled ah-is commonly performed using a chemiluminescence detector. However, water vapour and carbon dioxide affect the chemiluminescence process, The influence of these gases at the concentrations present in exhaled air has not vet been studied. For this in

  4. Human volunteer study with PGME: Eye irritation during vapour exposure

    NARCIS (Netherlands)

    Emmen, H.H.; Muijser, H.; Arts, J.H.E.; Prinsen, M.K.

    2003-01-01

    The objective of this study was to establish the possible occurrence of eye irritation and subjective symptoms in human volunteers exposed to propylene glycol monomethyl ether (PGME) vapour at concentrations of 0, 100 and 150 ppm. Testing was conducted in 12 healthy male volunteers using a repeated

  5. Condensation of saturated vapours on isentropic compression: a simple criterion

    Energy Technology Data Exchange (ETDEWEB)

    Patwardhan, V.S.

    1987-01-01

    A criterion is derived and tested for determining whether the isentropic compression of saturated vapours leads to superheat or condensation. This criterion needs only values of the critical temperature, the acentric factor and the liquid specific heat. The application of the criterion for selection of a working fluid both for heat pumps and heat engines is discussed.

  6. Detection of quadrupole relaxation in an optically pumped cesium vapour

    Energy Technology Data Exchange (ETDEWEB)

    Bernabeu, E.; Tornos, J.

    1985-10-01

    The relaxation of quadrupole orientation induced by means of optical pumping in a cesium vapour is experimentally studied, and the results are compared to the theoretical predictions. The optical detection process of this type of orientation is also discussed as a function of the polarization and spectral profile of the detection light.

  7. Consistent vapour-liquid equilibrium data containing lipids

    DEFF Research Database (Denmark)

    Cunico, Larissa; Ceriani, Roberta; Sarup, Bent

    for their mixtures in open literature, what makes necessary the development of reliable predictive models based on limited data. To contribute to the missing data, measurements of isobaric vapour-liquid equilibrium (VLE) data of three binary mixtures at two different pressures were performed at State University...

  8. Human volunteer study with PGME: Eye irritation during vapour exposure

    NARCIS (Netherlands)

    Emmen, H.H.; Muijser, H.; Arts, J.H.E.; Prinsen, M.K.

    2003-01-01

    The objective of this study was to establish the possible occurrence of eye irritation and subjective symptoms in human volunteers exposed to propylene glycol monomethyl ether (PGME) vapour at concentrations of 0, 100 and 150 ppm. Testing was conducted in 12 healthy male volunteers using a repeated

  9. Resonant CARS Spectroscopy of s-Tetrazine Vapour

    NARCIS (Netherlands)

    Aartsma, Thijs J.; Hesselink, Wim H.; Wiersma, Douwe A.

    1980-01-01

    CARS experiments on s-tetrazine vapour show that the eletronic resonance enhancement in the Q-branch is most effective for the lower J values. This suggests that the radiationless relaxation rate in the excited state increases with rotational quantum number. Delayed picosecond CARS experiments indic

  10. Vapour intrusion from the vadose zone—seven algorithms compared

    NARCIS (Netherlands)

    Provoost, J.; Bosman, A.; Reijnders, L.; Bronders, J.; Touchant, K.; Swartjes, F.

    2010-01-01

    Background, aim and scope: Vapours of volatile organic compounds (VOCs) emanating from contaminated soils may move through the unsaturated zone to the subsurface. VOC in the subsurface can be transported to the indoor air by convective air movement through openings in the foundation and basement. On

  11. Modelling the budget of middle atmospheric water vapour isotopes

    NARCIS (Netherlands)

    Zahn, A.; Franz, P.; Bechtel, C.; Grooss, J.U.; Röckmann, T.

    2006-01-01

    A one-dimensional chemistry model is applied to study the stable hydrogen (D) and stable oxygen isotope (17O, 18O) composition of water vapour in stratosphere and mesosphere. In the troposphere, this isotope composition is determined by “physical” fractionation effects, that are phase changes (e.g.

  12. Hg0 absorption in potassium persulfate solution

    Institute of Scientific and Technical Information of China (English)

    YE Qun-feng; WANG Cheng-yun; WANG Da-hui; SUN Guan; XU Xin-hua

    2006-01-01

    The aqueous phase oxidation of gaseous elemental mercury (Hg0) by potassium persulfate (KPS) catalyzed by Ag+was investigated using a glass bubble column reactor. Concentration of gaseous mercury and potassium persulfate were measured by cold vapor atom absorption (CVAA) and ion chromatograph (IC), respectively. The effects of pH value, concentration of potassium persulfate and silver nitrate (SN), temperature, Hg0 concentration in the reactor inlet and tertiary butanol (TBA), free radical scavenger, on the removal efficiency of Hg0 were studied. The results showed that the removal efficiency of Hg0 increased with increasing concentration of potassium persulfate and silver nitrate, while temperature and TBA were negatively effective. Furthermore, the removal efficiency of Hg0 was much better in neutral solution than in both acidic and alkaline solution. But the influence of pH was almost eliminated by adding AgNO3. High Hg0 concentration has positive effect. The possible reaction mechanism of gaseous mercury was also discussed.

  13. Antifungal Activity of Clove Essential Oil and its Volatile Vapour Against Dermatophytic Fungi

    OpenAIRE

    2007-01-01

    Antifungal activities of clove essential oil and its volatile vapour against dermatophytic fungi including Candida albicans, Epidermophyton floccosum. Microsporum audouinii, Trichophyton mentagrophytes, and Trichophyton rubrum were investigated. Both clove essential oil and its volatile vapour strongly inhibit spore germination and mycelial growth of the dermatophytic fungi tested. The volatile vapour of clove essential oil showed fungistatic activity whereas direct application of clove essen...

  14. 46 CFR 53.05-1 - Safety valve requirements for steam boilers (modifies HG-400 and HG-401).

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Safety valve requirements for steam boilers (modifies HG... requirements for steam boilers (modifies HG-400 and HG-401). (a) The pressure relief valve requirements and the safety valve requirements for steam boilers must be as indicated in HG-400 and HG-401 of section IV...

  15. Investigation of Hg uptake and transport between paddy soil and rice seeds combining Hg isotopic composition and speciation

    Directory of Open Access Journals (Sweden)

    C. Feng

    2016-02-01

    Full Text Available Abstract Human consumption of rice constitutes a potential toxicological risk in mercury (Hg polluted areas such as Hg mining regions in China. It is recognized to be an important source of Hg for the local human diet considering the efficient bioaccumulation of methylmercury (MeHg in rice seed. To assess Hg sources and uptake pathways to the rice plants, Hg speciation and isotopic composition were investigated in rice seeds and their corresponding paddy soils from different locations within the Wanshan Hg mining area (Guizhou Province, China. A large variation of Hg speciation is observed in rice seeds and paddy soils irrespective of the sampling location. Mass dependent fractionation (MDF of Hg in rice seeds differs by up to ∼4.0 ‰ in δ202Hg values, while mass independent fractionation (MIF of Hg isotopes remains constant (Δ199Hg ∼ 0‰. Hg isotopic composition in rice seeds covaries with that of paddy soils but exhibits lighter isotopic signature (δ202Hg. Such isotopic offset is mainly attributed to plant uptake and translocation processes. Also, seeds containing higher MeHg (MeHg/total Hg > 50% have significantly heavier Hg isotopes suggesting that MeHg uptake and transport to the seed in such rice plants is facilitated compared to inorganic Hg.

  16. Vapour-liquid equilibrium relationship between toluene and mixed surfactants.

    Science.gov (United States)

    Tian, Senlin; Li, Yingjie; Mo, Hong; Ning, Ping

    2012-01-01

    Micellar partitioning of volatile organic compounds (VOCs) in surfactant solutions and its effects on vapour-liquid equilibrium is fundamental to the overall design and implementation ofsurfactant-enhanced remediation. Knowledge of the vapour-liquid equilibrium partitioning coefficients for VOCs, especially in contaminated soils and groundwater in which they exist, is required. Headspace experiments were performed to quantify the effect of three mixed surfactants, cetyltrimethyl ammonium bromide (CTMAB) with tetrabutylammonium bromide (TBAB), sodium dodecyl sulphate (SDS) with Triton X-405 (TX405), and CTMAB with Triton X-100 (TX100), on the apparent Henry's constants (Hc) of toluene at temperatures ranging from 25 degrees C to 40 degrees C. The Hc values were significantly reduced in the presence of all three mixed surfactants at concentrations above their critical micelle concentrations (CMC). Mixed micellar partitioning, showing effects on the vapour-liquid equilibrium of toluene, was primarily responsible for the significant reduction of Hc in their mixed systems. The mixed surfactants CTMAB-TX100 had the greatest effect on Hc above the CMC, followed by SDS-TX405, then CTMAB-TBAB. Mixed systems of CTMAB-TX100 decreased Hc at concentrations significantly lower than the SDS-TX405 and CTMAB-TBAB concentrations, because of to the lower CMC of CTMAB-TX100. Vapour-liquid equilibrium data were also tested against the model (Hc = H/(1 + K(X - CMC)) that described the partitioning of VOCs in vapour-water-micelle phases. The correlation of Hc with mixed surfactant concentrations (X) and CMC can be utilized as an effective tool to predict the Hc by mixed surfactants.

  17. Long-term Hg pollution induced Hg tolerance in the terrestrial isopod Porcellio scaber (Isopoda, Crustacea).

    Science.gov (United States)

    Lapanje, A; Drobne, D; Nolde, N; Valant, J; Muscet, B; Leser, V; Rupnik, M

    2008-06-01

    The aim of our work was to assess the pollution-induced community tolerance (PICT) of isopod gut microbiota and pollution-induced isopod population tolerance (PIPT). Animals collected from a chronically Hg polluted and an unpolluted location were exposed for 14 days to 10microg Hg/g dry food under laboratory conditions. The lysosomal membrane stability, hepatopancreas epithelium thickness, feeding activity and animal bacterial gut microbiota composition were determined. The results confirm the hypothesis that the response to short-term Hg exposure differs for animals from the Hg polluted and the unpolluted field locations. The animals and their gut microbiota from the Hg polluted location were less affected by Hg in a short-term feeding experiment than those from the unpolluted environment. We discuss the pollution-induced population tolerance of isopods and their gut microbiota as a measure of effects of long-term environmental pollution. The ecological consequences of such phenomena are also discussed.

  18. Zuotai and HgS differ from HgCl2 and methyl mercury in Hg accumulation and toxicity in weanling and aged rats.

    Science.gov (United States)

    Zhang, Bin-Bin; Li, Wen-Kai; Hou, Wei-Yu; Luo, Ya; Shi, Jing-Zhen; Li, Cen; Wei, Li-Xin; Liu, Jie

    2017-09-15

    Mercury sulfides are used in Ayurvedic medicines, Tibetan medicines, and Chinese medicines for thousands of years and are still used today. Cinnabar (α-HgS) and metacinnabar (β-HgS) are different from mercury chloride (HgCl2) and methylmercury (MeHg) in their disposition and toxicity. Whether such scenario applies to weanling and aged animals is not known. To address this question, weanling (21d) and aged (450d) rats were orally given Zuotai (54% β-HgS, 30mg/kg), HgS (α-HgS, 30mg/kg), HgCl2 (34.6mg/kg), or MeHg (MeHgCl, 3.2mg/kg) for 7days. Accumulation of Hg in kidney and liver, and the toxicity-sensitive gene expressions were examined. Animal body weight gain was decreased by HgCl2 and to a lesser extent by MeHg, but unaltered after Zuotai and HgS. HgCl2 and MeHg produced dramatic tissue Hg accumulation, increased kidney (kim-1 and Ngal) and liver (Ho-1) injury-sensitive gene expressions, but such changes are absent or mild after Zuotai and HgS. Aged rats were more susceptible than weanling rats to Hg toxicity. To examine roles of transporters in Hg accumulation, transporter gene expressions were examined. The expression of renal uptake transporters Oat1, Oct2, and Oatp4c1 and hepatic Oatp2 was decreased, while the expression of renal efflux transporter Mrp2, Mrp4 and Mdr1b was increased following HgCl2 and MeHg, but unaffected by Zuotai and HgS. Thus, Zuotai and HgS differ from HgCl2 and MeHg in producing tissue Hg accumulation and toxicity, and aged rats are more susceptible than weanling rats. Transporter expression could be adaptive means to reduce tissue Hg burden. Copyright © 2017 Elsevier Inc. All rights reserved.

  19. Local probing of Hg neighboorhood in HgBa$_{2}$CuO$_{4+\\delta}$

    CERN Document Server

    Correia, J G; Loureiro, S M; Toulemonde, P; Le Floc'h, S; Bordet, P; Capponi, J J; Gatt, R; Tröger, W; Ctortecka, B; Butz, T; Haas, H; Marques, J G; Soares, J C

    2000-01-01

    Electric field gradients (EFG) on mercury sites of the Hg1201 high-TC superconductors were measured with the perturbed angular correlation (PAC) technique. In Hg1201 samples where PAC detects higher oxygen content the EFGs have decreased to lower values indicating an elongation of the Hg-apical oxygen dumb-bell. On the same samples the asymmetry parameter of the EFG becomes non-zero below 100 K, showing that the charge distribution near the Hg-apical oxygen chain becomes non-axially symmetric at low temperature.

  20. Complexation of Hg with phytochelatins is important for plant Hg tolerance.

    Science.gov (United States)

    Carrasco-Gil, Sandra; Alvarez-Fernández, Ana; Sobrino-Plata, Juan; Millán, Rocío; Carpena-Ruiz, Ramón O; Leduc, Danika L; Andrews, Joy C; Abadía, Javier; Hernández, Luís E

    2011-05-01

    Three-week-old alfalfa (Medicago sativa), barley (Hordeum vulgare) and maize (Zea mays) were exposed for 7 d to 30 µm of mercury (HgCl(2) ) to characterize the Hg speciation in root, with no symptoms of being poisoned. The largest pool (99%) was associated with the particulate fraction, whereas the soluble fraction (SF) accounted for a minor proportion (phytochelatins (PCs) in root SF, which was particularly varied in alfalfa (eight ligands and five stoichiometries), a species that also accumulated homophytochelatins. Spatial localization of Hg in alfalfa roots by microprobe synchrotron X-ray fluorescence spectroscopy showed that most of the Hg co-localized with sulphur in the vascular cylinder. Extended X-ray Absorption Fine Structure (EXAFS) fingerprint fitting revealed that Hg was bound in vivo to organic-S compounds, i.e. biomolecules containing cysteine. Albeit a minor proportion of total Hg, Hg-PCs complexes in the SF might be important for tolerance to Hg, as was found with Arabidopsis thaliana mutants cad2-1 (with low glutathione content) and cad1-3 (unable to synthesize PCs) in comparison with wild type plants. Interestingly, high-performance liquid chromatography-electrospray ionization-time of flight analysis showed that none of these mutants accumulated Hg-biothiol complexes.

  1. Magnetic fields of HgMn stars

    CERN Document Server

    Hubrig, S; Ilyin, I; Korhonen, H; Schoeller, M; Savanov, I; Arlt, R; Castelli, F; Curto, G Lo; Briquet, M; Dall, T H

    2012-01-01

    The frequent presence of weak magnetic fields on the surface of spotted late-B stars with HgMn peculiarity in binary systems has been controversial during the two last decades. We re-analyse available spectropolarimetric material by applying the moment technique on spectral lines of inhomogeneously distributed elements separately. Furthermore, we present new determinations of the mean longitudinal magnetic field for the HgMn star HD65949 and the hotter analog of HgMn stars, the PGa star HD19400, using FORS2 installed at the VLT. We also give new measurements of the eclipsing system AR Aur with a primary star of HgMn peculiarity which were obtained with the SOFIN spectropolarimeter installed at the Nordic Optical Telescope. We downloaded from the ESO archive the publically available HARPS spectra for eight HgMn stars and one normal and one superficially normal B-type star obtained in 2010. The application of the moment technique to the HARPS and SOFIN spectra allowed us to study the presence of the longitudina...

  2. HgCdTe barrier infrared detectors

    Science.gov (United States)

    Kopytko, M.; Rogalski, A.

    2016-05-01

    In the last decade, new strategies to achieve high-operating temperature (HOT) detectors have been proposed, including barrier structures such as nBn devices, unipolar barrier photodiodes, and multistage (cascade) infrared detectors. The ability to tune the positions of the conduction and valence band edges independently in a broken-gap type-II superlattices is especially helpful in the design of unipolar barriers. This idea has been also implemented in HgCdTe ternary material system. However, the implementation of this detector structure in HgCdTe material system is not straightforward due to the existence of a valence band discontinuity (barrier) at the absorber-barrier interface. In this paper we present status of HgCdTe barrier detectors with emphasis on technological progress in fabrication of MOCVD-grown HgCdTe barrier detectors achieved recently at the Institute of Applied Physics, Military University of Technology. Their performance is comparable with state-of-the-art of HgCdTe photodiodes. From the perspective of device fabrication their important technological advantage results from less stringent surface passivation requirements and tolerance to threading dislocations.

  3. Photoluminescence of ZnSe-ZnS Single Quantum Wells Grown by Vapour Phase Epitaxy

    Institute of Scientific and Technical Information of China (English)

    吕有明; 申德振; 刘益春; 李炳辉; 张吉英; 范希武; 饭田诚之; 加藤有行

    2002-01-01

    We study the photoluminescence (PL) of ultra thin layer ZnSe quantum wells in ZnS barriers. Samples with different well widths are grown by vapour phase epitaxy and the PL spectra of these samples are measured by the excitation of a 500 W Hg lamp. The peak positions of the bands coming from the excitonic luminescence show a larger blueshift with respect to the energy of free excitons in the ZnSe bulk material. The observed variation of the full width at half maximum and peak position of the bands in the spectra with the well width are interpreted to the formation of the ZnSxSe1-x alloy layer due to the interdiffusion in the interfaces between ZnSe and ZnS.According to the behaviour of the excitons in the smaller conduction band offset, the exciton binding energy is estimated from the dependence of the PL intensity on the temperature. From this result, excitons seem to show nearly three-dimensional characteristics.

  4. A new test method for measuring the water vapour permeability of fabrics

    Science.gov (United States)

    Huang, Jianhua; Qian, Xiaoming

    2007-09-01

    The water vapour permeability of textile fabrics is a critical determinant of wearer comfort. Existing test methods are either time consuming or require large amounts of material. A new test apparatus was developed for characterizing the water vapour permeability of fabrics. An aluminium cylinder covered with waterproof and vapour permeable PTFE laminate is used for generating water vapour source on one side of the sample. A dry nitrogen sweep gas stream is used to carry water vapour away. The calculation of the rate of water vapour transmission across the fabric is based on the measurement of the relative humidity of the outgoing nitrogen stream. This new measuring apparatus offers a short test time and calls for a small sample size. The comparison measurements show that the test results correlated well with those obtained from ISO 11092 and ASTM E96. Therefore, this test method provides a new technique to accurately and precisely characterize the water vapour transport properties of fabrics.

  5. Effects of an Applied Magnetic Field on the Directional Solidification of Hg(1-x)Zn(x)Se Alloys

    Science.gov (United States)

    Cobb, S. D.; Lehoczky, S. L.; Szofran, F. R.; Jones, K. S.

    1999-01-01

    Directionally solidified Hg(0.9)Zn(0.1)Se alloys were studied as an alternative to HgCdTe for the detection of electromagnetic radiation because of predicted improvements in lattice stability. Several boules were grown using a modified Bridgman-Stockbarger method and in an applied magnetic field. Axial compositional profiles showed mass transfer was primarily diffusion controlled. Radial compositional variations were greatly reduced when solidification occurred in an applied magnetic field. Microstructural characteristics and dislocation etch pit densities were greatly improved over HgTe based alloys. The extreme importance of processing conditions on defect generation was illustrated by comparing ampoule configurations and thermal profiles.

  6. Complexation of Hg with phytochelatins is important for plant Hg tolerance

    National Research Council Canada - National Science Library

    CARRASCO‐GIL, SANDRA; ÁLVAREZ‐FERNÁNDEZ, ANA; SOBRINO‐PLATA, JUAN; MILLÁN, ROCÍO; CARPENA‐RUIZ, RAMÓN O; LEDUC, DANIKA L; ANDREWS, JOY C; ABADÍA, JAVIER; HERNÁNDEZ, LUÍS E

    2011-01-01

    Three‐week‐old alfalfa ( Medicago sativa ), barley ( Hordeum vulgare ) and maize ( Zea mays ) were exposed for 7 d to 30  µ m of mercury (HgCl 2 ) to characterize the Hg speciation in root, with no symptoms of being poisoned...

  7. Temporal Characteristics of Emission of Working Mixtures of a HgBr/HgCl Excimer Lamp

    Science.gov (United States)

    Malinin, A. N.; Guĭvan, N. N.; Shimon, L. L.; Polyak, A. V.; Zubrilin, N. G.; Shchedrin, A. I.

    2001-12-01

    Results of a study of temporal characteristics of the emission of gas-discharge plasma of atmospheric pressure in multicomponent mixtures (mercury dibromide and dichloride with helium and additions of molecular nitrogen and xenon) of working media of HgBr/HgCl excimer lamps are presented. Gas-discharge plasma was produced and components of the working mixture were excited by high-frequency barrier and surface discharges occurring simultaneously. The repetition rate of the pumping pulse and its duration are 1000 Hz and ˜100 ns, respectively. It is found that the amplitude and the length of emission pulses and their trailing edge are modified in HgBr2: HgCl2: Xe: He and HgBr2: HgCl2: N2: He mixtures when xenon and molecular nitrogen are added, as compared to a HgBr2: HgCl2: He mixture. Regularities observed in temporal characteristics of gas-discharge plasma emission are discussed.

  8. Ground-state potential energy curves of LiHg, NaHg, and KHg revisited

    Science.gov (United States)

    Thiel, Linda; Hotop, Hartmut; Meyer, Wilfried

    2003-11-01

    We present the results of large-scale CCSD(T) calculations on the potential energy curves for the ground states of LiHg, NaHg, and KHg. In these calculations, the Hg20+ core is simulated by a pseudopotential which has been adjusted to reproduce experimental excitation and ionization energies of the Hg atom at the coupled-cluster level. Moreover, we apply a weighted multiproperty fitting procedure to determine reliable potentials for LiHg, NaHg, and KHg which reproduce the available experimental results. In the case of LiHg, this best-fit potential is based solely on experimental data and its agreement with our calculated potential supports our computational procedure. For NaHg and KHg the experimental data had to be complemented by theoretical results in order to fix a best-fit potential. Our potentials and those proposed previously are evaluated by comparing calculated scattering cross sections and vibrational energy levels with the available experimental data.

  9. Quasiparticle excitations in superdeformed {sup 192}Hg

    Energy Technology Data Exchange (ETDEWEB)

    Lauritsen, T.; Carpenter, M.P.; Janssens, R.V.F. [and others

    1995-08-01

    The nucleus {sup 192}Hg plays a pivotal role for superdeformation in the mass 190 region, since calculations of single-particle levels show large shell-gaps for the superdeformed (SD) shape at N = 112 and Z = 80. As a result, {sup 192}Hg is referred to as the doubly magic SD nucleus for the A = 190 region. In previous studies, only one superdeformed band was observed in this nucleus, and this fact was cited as indirect evidence that large shell gaps do indeed exist at the proposed particle numbers.

  10. Electric field gradients in Hg compounds

    DEFF Research Database (Denmark)

    Arcisauskaité, Vaida; Knecht, Stefan; Sauer, Stephan P. A.

    2012-01-01

    We examine the performance of Density Functional Theory (DFT) approaches based on the Zeroth-Order Regular Approximation (ZORA) Hamiltonian (with and without inclusion of spinorbit coupling) for predictions of electric ¿eld gradients (EFGs) at the heavy atom Hg nucleus. This is achieved by compar......We examine the performance of Density Functional Theory (DFT) approaches based on the Zeroth-Order Regular Approximation (ZORA) Hamiltonian (with and without inclusion of spinorbit coupling) for predictions of electric ¿eld gradients (EFGs) at the heavy atom Hg nucleus. This is achieved...

  11. Mapping of tritium emissions using absorption vapour samplers.

    Science.gov (United States)

    Vodila, Gergely; Molnár, Mihály; Veres, Mihály; Svingor, Eva; Futó, István; Barnabás, István; Kapitány, Sándor

    2009-02-01

    Püspökszilágy Radioactive Waste Treatment and Disposal Facility (RWTDF) is a typical near-surface engineered repository designated to store low- and intermediate-level wastes from various institutes, research facilities and hospitals in Hungary. Two automatic combined (14)C-tritium sampling units installed at the facility sample the air 2 m above surface. The one installed near the vaults detects tritium (T) activities two orders of magnitude higher than the far reference sampling unit. To localize the T emissions, 19 small absorption vapour samplers filled with silica gel were settled onto the ground surface. After the saturation of the silica gel, the water was recovered and its T concentration was measured with a low-background liquid scintillation counter. The absorption vapour samplers are cheap, simple and easy-to-use. We present the samplers and the T distribution map constructed from the data, which helps to localize the T emission.

  12. Vapour pressure and enthalpy of vaporization of aliphatic dialkyl carbonates

    Energy Technology Data Exchange (ETDEWEB)

    Kozlova, Svetlana A.; Emel' yanenko, Vladimir N.; Georgieva, Miglena [Department of Physical Chemistry, University of Rostock, Hermannstrasse 14, D-18051 Rostock (Germany); Verevkin, Sergey P. [Department of Physical Chemistry, University of Rostock, Hermannstrasse 14, D-18051 Rostock (Germany)], E-mail: sergey.verevkin@uni-rostock.de; Chernyak, Yury [Huntsman Corporation, Advanced Technology Center, 8600 Gosling Road, The Woodlands, TX 77381 (United States); Schaeffner, Benjamin; Boerner, Armin [Leibniz Institut fuer Katalyse an der Universitaet Rostock e.V., Albert-Einstein Strasse 29a, 18059 Rostock (Germany)

    2008-07-15

    Molar enthalpies of vaporization of aliphatic alkyl carbonates: dimethyl carbonate [616-38-6], diethyl carbonate [105-58-8], di-n-propyl carbonate [623-96-1], di-n-butyl carbonate [542-52-9], and dibenzyl carbonate [3459-92-5] were obtained from the temperature dependence of the vapour pressure measured by the transpiration method. A large number of the primary experimental results on temperature dependences of vapour pressures have been collected from the literature and have been treated uniformly in order to derive vaporization enthalpies of dialkyl carbonates at the reference temperature 298.15 K. An internal consistency check was performed on enthalpy of vaporization values for dialkyl carbonates studied in this work.

  13. Study of vapour pressure of lithium nitrate solutions in ethanol

    Energy Technology Data Exchange (ETDEWEB)

    Verevkin, Sergey [Abteilung Physikalische Chemie, Institut fuer Chemie, Universitaet Rostock, Hermannstrasse, 14, D-18055 Rostock (Germany); Safarov, Javid [Heat and Refrigeration Techniques, Azerbaijan Technical University, H. Javid Avn. 25, AZ1073 Baku (Azerbaijan)]. E-mail: javids@azdata.net; Bich, Eckard [Abteilung Physikalische Chemie, Institut fuer Chemie, Universitaet Rostock, Hermannstrasse, 14, D-18055 Rostock (Germany); Hassel, Egon [Lehrstuhl fuer Technische Thermodynamik, Fakultaet Maschinenbau und Schiffstechnik, Universitaet Rostock, Albert-Einstein-Str. 2, D-18059 Rostock (Germany); Heintz, Andreas [Abteilung Physikalische Chemie, Institut fuer Chemie, Universitaet Rostock, Hermannstrasse, 14, D-18055 Rostock (Germany)

    2006-05-15

    Vapour pressure p of (LiNO{sub 3} + C{sub 2}H{sub 5}OH) solutions at T = (298.15 to 323.15) K were measured, osmotic, activity coefficients ({phi}, {gamma}) and activity of solvent a {sub s} have been evaluated. The experiments were carried out in the molality range m = (0.19125 to 2.21552) mol . kg{sup -1}. The Antoine equation was used for the empirical description of the experimental vapour pressure results and the (Pitzer + Mayorga) model with inclusion of Archer's ionic strength dependence of the third virial coefficient for the calculated osmotic coefficients were used. The parameters of the Archer for the extended Pitzer model was used for the evaluation of activity coefficients.

  14. Navier slip model of drag reduction by Leidenfrost vapour layers

    OpenAIRE

    Berry, Joseph D; Vakarelski, Ivan U.; Chan, Derek Y. C.; Thoroddsen, Sigurdur T.

    2016-01-01

    Recent experiments found that a hot solid sphere that is able to sustain a stable Leidenfrost vapour layer in a liquid exhibits significant drag reduction during free fall. The variation of the drag coefficient with Reynolds number shows substantial deviation from the characteristic drag crisis behavior at high Reynolds numbers. Results obtained with liqiuds of different viscosities show that onset of the drag crisis depends on the viscosity ratio of the vapor to the liquid. The key feature o...

  15. Combined Dial Sounding of Ozone, Water Vapour and Aerosol

    OpenAIRE

    Trickl Thomas; Vogelmann Hannes

    2016-01-01

    Routine high-quality lidar measurements of ozone, water vapour and aerosol at Garmisch-Partenkirchen since 2007 have made possible more comprehensive atmospheric studies and lead to a growing insight concerning the most frequently occurring long-range transport pathways. In this contribution we present as examples results on stratospheric layers travelling in the free troposphere for extended periods of time without eroding. In particular, we present a case of an intrusion layer that subsided...

  16. Probabilistic risk assessment for six vapour intrusion algorithms

    OpenAIRE

    Provoost, J.; Reijnders, L.; Bronders, J.; Van Keer, I.; Govaerts, S.

    2014-01-01

    A probabilistic assessment with sensitivity analysis using Monte Carlo simulation for six vapour intrusion algorithms, used in various regulatory frameworks for contaminated land management, is presented here. In addition a deterministic approach with default parameter sets is evaluated against observed concentrations for benzene, ethylbenzene and trichloroethylene. The screening-level algorithms are ranked according to accuracy and conservatism in predicting observed soil air and indoor air ...

  17. Aqueous solvation of Hg(OH)2: energetic and dynamical density functional theory studies of the Hg(OH)2-(H2O)n (n = 1-24) structures.

    Science.gov (United States)

    Amaro-Estrada, J I; Maron, L; Ramírez-Solís, A

    2013-09-19

    A systematic study of the hydration of Hg(OH)2 by the stepwise solvation approach is reported. The optimized structures, solvation energies, and incremental free energies of 1-24 water molecules interacting with the solute have been computed at the B3PW91 level using 6-31G(d,p) basis sets for the O and H atoms. The mercury atom was treated with the Stuttgart-Köln relativistic core potential in combination with an extended optimized valence basis set. One to three direct Hg-water interactions appear along the solvation process. The first solvation shell is fully formed with 24 water molecules. A stable pentacoordinated Hg trigonal bipyramid structure appears for n > 15. Density functional theory (DFT) Born-Oppenheimer molecular dynamics simulations showed the thermal stability of the Hg(OH)2-(H2O)24 structure at room temperature and the persistence of the trigonal bipyramid coordination around Hg. The Gibbs free energy for the first solvation shell is significantly larger for the fully solvated Hg(OH)2 than the one previously obtained for the HgCl2 case, due to σ-acceptor and π-donor properties involving the hydroxyl groups of the solute. This suggests that the transmembrane passage of Hg(OH)2 into the cell via simple diffusion is less favorable compared to the case when the metal is coordinated with two Cl groups.

  18. Growing rice aerobically markedly decreases mercury accumulation by reducing both Hg bioavailability and the production of MeHg.

    Science.gov (United States)

    Wang, Xun; Ye, Zhihong; Li, Bing; Huang, Linan; Meng, Mei; Shi, Jianbo; Jiang, Guibin

    2014-01-01

    Rice consumption represents a major route of mercury (Hg) and methylmercury (MeHg) exposure for those living in certain areas of inland China. In this study we investigated the effects of water management on bioavailable Hg, MeHg, and sulfate-reducing bacteria (SRB, abundance and community composition) in rhizosphere soil, and total Hg (THg) and MeHg in rice plants grown under glasshouse and paddy field conditions. Aerobic conditions greatly decreased the amount of THg and MeHg taken up by rice plants and affected their distribution in different plant tissues. There were positive correlations between bioavailable Hg and THg in brown rice and roots and between numbers of SRB and MeHg in brown rice, roots, and rhizosphere soil. Furthermore, the community composition of SRB was dramatically influenced by the water management regimes. Our results demonstrate that the greatly reduced bioavailability of Hg and production of MeHg are due to decreased SRB numbers and proportion of Hg methylators in the rhizosphere under aerobic conditions. These are the main reasons for the reduced Hg and MeHg accumulation in aerobically grown rice. Water management is indicated as an effective measure that can be used to reduce Hg and MeHg uptake by rice plants from Hg-contaminated paddy fields.

  19. 40 CFR 60.45Da - Standard for mercury (Hg).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for mercury (Hg). 60.45Da... for mercury (Hg). (a) For each coal-fired electric utility steam generating unit other than an IGCC... gases that contain mercury (Hg) emissions in excess of each Hg emissions limit in paragraphs...

  20. MBE Growth and Characterization of Hg Based Compounds and Heterostructures

    Science.gov (United States)

    2002-06-03

    The molecular beam epitaxy ( MBE ) growth of Mercury Cadmium Telluride (Hg(1-x)Cd(x)Te) alloys and type III HgTe/Hg(1-x)Cd(x)Te heterostructures has...been discussed, including similarities and differences between the (0 0 1) and (1 1 2)Beta orientations. Furthermore, the MBE growth of HgTe-based

  1. Phenylselenolate Mercury Alkyl Compounds, PhSeHgMe and PhSeHgEt: Molecular Structures, Protolytic Hg-C Bond Cleavage and Phenylselenolate Exchange.

    Science.gov (United States)

    Yurkerwich, Kevin; Quinlivan, Patrick J; Rong, Yi; Parkin, Gerard

    2016-01-08

    The phenylselenolate mercury alkyl compounds, PhSeHgMe and PhSeHgEt, have been structurally characterized by X-ray diffraction, thereby demonstrating that both compounds are monomeric with approximately linear coordination geometries; the mercury centers do, nevertheless, exhibit secondary Hg•••Se intermolecular interactions that serve to increase the coordination number in the solid state. The ethyl derivative, PhSeHgEt, undergoes facile protolytic cleavage of the Hg-C bond to release ethane at room temperature, whereas PhSeHgMe exhibits little reactivity under similar conditions. Interestingly, the cleavage of the Hg-C bond of PhSeHgEt is also more facile than that of the thiolate analogue, PhSHgEt, which demonstrates that coordination by selenium promotes protolytic cleavage of the mercury-carbon bond. The phenylselenolate compounds PhSeHgR (R = Me, Et) also undergo degenerate exchange reactions with, for example, PhSHgR and RHgCl. In each case, the alkyl groups preserve coupling to the (199)Hg nuclei, thereby indicating that the exchange process involves metathesis of the Hg-SePh/Hg-X groups rather than metathesis of the Hg-R/Hg-R groups.

  2. The application of 199Hg NMR and 199mHg perturbed angular correlation (PAC) spectroscopy to define the biological chemistry of HgII

    DEFF Research Database (Denmark)

    Iranzo, Olga; Thulstrup, Peter Waaben; Ryu, Seung-baek;

    2007-01-01

    H values and at peptide/HgII ratios of 3:1 with an unusual trigonal thiolate coordination mode. The resulting HgII complexes are good water-soluble models for HgII binding to the protein MerR. We have carried out a parallel study using 199Hg NMR and 199mHg perturbed angular correlation (PAC) spectroscopy...... to characterize the distinct species that are generated under different pH conditions and peptide TRI L9C/HgII ratios. These studies prove for the first time the formation of [Hg{(TRI L9C)2-(TRI L9C H)}], a dithiolate-HgII complex in the hydrophobic interior of the three-stranded coiled coil (TRI L9C)3. 199Hg NMR...... and 199mHg PAC data demonstrate that this dithiolate-HgII complex is different from the dithiolate [Hg(TRI L9C)2], and that the presence of third -helix, containing a protonated cysteine, breaks the symmetry of the coordination environment present in the complex [Hg(TRI L9C)2]. As the pH is raised...

  3. Magnetic fields of HgMn stars

    DEFF Research Database (Denmark)

    Hubrig, S.; Gonzalez, J. F.; Ilyin, I.

    2012-01-01

    Context. The frequent presence of weak magnetic fields on the surface of spotted late-B stars with HgMn peculiarity in binary systems has been controversial during the two last decades. Recent studies of magnetic fields in these stars using the least-squares deconvolution (LSD) technique have fai...

  4. High-Rate Growth and Nitrogen Distribution in Homoepitaxial Chemical Vapour Deposited Single-crystal Diamond

    Institute of Scientific and Technical Information of China (English)

    LI Hong-Dong; ZOU Guang-Tian; WANG Qi-Liang; CHENG Shao-Heng; LI Bo; L(U) Jian-Nan; L(U) Xian-Yi; JIN Zeng-Sun

    2008-01-01

    High rate (> 50 μm/h) growth of homoepitaxial single-crystal diamond (SCD) is carried out by microwave plasma chemical vapour deposition (MPCVD) with added nitrogen in the reactant gases of methane and hydrogen,using a polycrystalline-CVD-diamond-film-made seed holder. Photoluminescence results indicate that the nitrogen concentration is spatially inhomogeneous in a large scale,either on the top surface or in the bulk of those as-grown SCDs.The presence of N-distribution is attributed to the facts: (I) a difference in N-incorporation efficiency and (ii) N-diffusion,resulting from the local growth temperatures changed during the high-rate deposition process.In addition,the formed nitrogen-vacancy centres play a crucial role in N-diffusion through the growing crystal.Based on the N-distribution observed in the as-grown crystals,we propose a simple method to distinguish natural diamonds and man-made CVD SCDs.Finally,the disappearance of void defect on the top surface of SCDs is discussed to be related to a filling-in mechanism.

  5. Standardisation of a Vapour Generator for Calibration of Environmental Monitoring Instruments

    Directory of Open Access Journals (Sweden)

    Parul Rana

    2003-10-01

    Full Text Available Very low vapour pressure of 2,4,6 trinitrotoulene (TNT yields extremely low vapour concentrations at different flow rates in the air, yet considerable quantity of vapours and TNTdust during handling may be present at the workplace environment which is harmful to the health of the personnel working there. The explosive vapours, such as TNT,  2,6-dinitrotoluene (DNT, etc., though harmful to the health of the personnel, are not covered either in the emission standards or in the ambient air quality standards. Presently, no instrument is available for air monitoring of TNT vapours. These vapours need to be collected on-site to estimate TNT concentration. Realising the need for real-time air monitoring of TNT, efforts have been made to understand and device an instrument for on-site determination of TNT vapours parts per billiion (ppb range. Low-level TNT vapours and TNT buried in the soil in military operations are required to be detected. The instruments for this require careful calibration to yield accurate and reliable results. Hence, an effort has been made to develop a trace-level ppb vapour generator. The vapour generator of a spiral glass column of length 170 cm and inner diameter 4 mm 2 0.5 mm has been used. An activated charcoal glass tube has been used for sampling TNT vapours. The adsorbed TNT vapours were desorbed and analysed using high performance liquid chromatography. Thesolid support used has been studied. These vapours generated at different flow rates have been evaluated. The calibrated instrument can be used for in situ and on-site analysis of samples of TNT and also for samples collected.

  6. Frequency ratios of Sr, Yb and Hg based optical lattice clocks and their applications

    CERN Document Server

    Takamoto, Masao; Das, Manoj; Nemitz, Nils; Ohkubo, Takuya; Yamanaka, Kazuhiro; Ohmae, Noriaki; Takano, Tetsushi; Akatsuka, Tomoya; Yamaguchi, Atsushi; Katori, Hidetoshi

    2015-01-01

    This article describes the recent progress of optical lattice clocks with neutral strontium ($^{87}$Sr), ytterbium ($^{171}$Yb) and mercury ($^{199}$Hg) atoms. In particular, we present frequency comparison between the clocks locally via an optical frequency comb and between two Sr clocks at remote sites using a phase-stabilized fibre link. We first review cryogenic Sr optical lattice clocks that reduce the room-temperature blackbody radiation shift by two orders of magnitude and serve as a reference in the following clock comparisons. Similar physical properties of Sr and Yb atoms, such as transition wavelengths and vapour pressure, have allowed our development of a compatible clock for both species. A cryogenic Yb clock is evaluated by referencing a Sr clock. We also report on a Hg clock, which shows one order of magnitude less sensitivity to blackbody radiation, while its large nuclear charge makes the clock sensitive to the variation of fine-structure constant. Connecting all three types of clocks by an o...

  7. Developments in MOVPE HgCdTe arrays for passive and active infrared imaging

    Science.gov (United States)

    Baker, Ian; Maxey, Chris; Hipwood, Les; Weller, Harald; Thorne, Peter

    2012-09-01

    SELEX Galileo Infrared Ltd has developed a range of 3rd Generation infrared detectors based on HgCdTe grown by Metal Organic Vapour Phase Epitaxy (MOVPE) on low cost GaAs substrates. There have been four key development aims: reducing the cost especially for large arrays, extending the wavelength range, improving the operating temperature for lower power, size and weight cameras and increasing the functionality. Despite a 14% lattice mismatch between GaAs and HgCdTe MOVPE arrays show few symptoms of misfit dislocations even in longwave detectors. The key factors in the growth and device technology are described in this paper to explain at a scientific level the radiometric quality of MOVPE arrays. A feature of the past few years has been the increasingly sophisticated products that are emerging thanks to custom designed silicon readout devices. Three devices are described as examples: a multifunctional device that can operate as an active or passive imager with built-in range finder, a 3-side buttable megapixel array and an ultra-low noise device designed for scientific applications.

  8. Relationship Between Soil Properties and Different Fractions of Soil Hg

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Correlation and path analysis methods were used to study the relationship between soil properties and the distribution of different soil Hg fractions with nine representative soils from Chongqing, China. Results showed that clay (< 2 m) could increase water-soluble Hg (r = 0.700*). Soil organic matter (OM) could enhance the increase of elemental Hg (r = 0.674*). The higher the base saturation percentage (BSP), the more the residual Hg (r = 0.684*). Organic Hg, the sum of acid-soluble organic Hg. and alkali-soluble Hg, was positively affected by silt (2~20μm) but negatively affected by pH, with the direct path coefficients amounting to 1.0487 and 0.5121, respectively. The positive effect of OM and negative effect of BSP on organic Hg were the most significant, with the direct path coefficients being 0.7614 and -0.8527, respectively. The indirect effect of clay (< 2 μm) via BSP (path coefficient = 0.4186) was the highest, showing that the real influencing factor in the effect of clay (< 2 μm) on acid-soluble organic Hg was BSP. Since the available Hg fraction, water-soluble Hg, was positively affected by soil clay content, and the quite immobile and not bioavailable residual Hg by soil BSP, suitable reduction of clay content and increase of BSP would be of much help to reduce the Hg availability and Hg activity in Hg-contaminated soils.

  9. Factors affecting release of ethanol vapour in active modified atmosphere packaging systems for horticultural products

    Directory of Open Access Journals (Sweden)

    Weerawate Utto

    2014-04-01

    Full Text Available The active modified atmosphere packaging (active MAP system , which provides interactive postharvest control , using ethanol vapour controlled release, is one of the current interests in the development of active packaging for horticultural products. A number of published research work have discussed the relationship between the effectiveness of ethanol vapour and its concentration in the package headspace, including its effect on postharvest decay and physiological controls. This is of importance because a controlled release system should release and maintain ethanol vapour at effective concentrations during the desired storage period. A balance among the mass transfer processes of ethanol vapour in the package results in ethanol vapour accumulation in the package headspace. Key factors affecting these processes include ethanol loading, packaging material, packaged product and storage environment (temperature and relative h umidity. This article reviews their influences and discusses future work required to better understand their influences on ethanol vapour release and accumulations in active MAP.

  10. Hg/HgO electrode and hydrogen evolution potentials in aqueous sodium hydroxide

    Energy Technology Data Exchange (ETDEWEB)

    Nickell, Ryan A.; Zhu, Wenhua H.; Payne, Robert U.; Cahela, Donald R.; Tatarchuk, Bruce J. [Center for Microfibrous Materials Manufacturing, Department of Chemical Engineering, 230 Ross Hall, Auburn University, Auburn, AL 36849 (United States)

    2006-10-27

    The Hg/HgO electrode is usually utilized as a reference electrode in alkaline solution such as for development of an alkaline hydrogen electrode. The reference electrode provides a suitable reference point but is available from few commercial vendors and suffers from inadequate documentation on potential in varying electrolytes. A new numerical method uses activity, activity coefficients, and a few correlated empirical equations to determine the potential values in both dilute and concentrated sodium hydroxide solutions at temperatures of 0-90{sup o}C and at concentrations of 0.100-12.8mol kg{sub H{sub 2}O}{sup -1}. The computed potentials of the Hg/HgO electrodes versus a normal hydrogen electrode (NHE) at 25{sup o}C and 1atm are 0.1634V for 0.100m, 0.1077V for 1.00m, and 0.0976V for 1.45m NaOH solutions. The Hg/HgO reduction potential further changes to -0.0751V versus NHE and hydrogen evolution potential changes to -0.9916V versus NHE in a solution of 30.0wt.% NaOH at 80{sup o}C. The calculated values are compared with the measured data at 25 and 75{sup o}C. The experimental data agree well with the numerical values computed from the theoretical and empirical equations. (author)

  11. Hg/HgO electrode and hydrogen evolution potentials in aqueous sodium hydroxide

    Science.gov (United States)

    Nickell, Ryan A.; Zhu, Wenhua H.; Payne, Robert U.; Cahela, Donald R.; Tatarchuk, Bruce J.

    The Hg/HgO electrode is usually utilized as a reference electrode in alkaline solution such as for development of an alkaline hydrogen electrode. The reference electrode provides a suitable reference point but is available from few commercial vendors and suffers from inadequate documentation on potential in varying electrolytes. A new numerical method uses activity, activity coefficients, and a few correlated empirical equations to determine the potential values in both dilute and concentrated sodium hydroxide solutions at temperatures of 0-90 °C and at concentrations of 0.100-12.8 mol k gH2O-1 . The computed potentials of the Hg/HgO electrodes versus a normal hydrogen electrode (NHE) at 25 °C and 1 atm are 0.1634 V for 0.100m, 0.1077 V for 1.00m, and 0.0976 V for 1.45m NaOH solutions. The Hg/HgO reduction potential further changes to -0.0751 V versus NHE and hydrogen evolution potential changes to -0.9916 V versus NHE in a solution of 30.0 wt.% NaOH at 80 °C. The calculated values are compared with the measured data at 25 and 75 °C. The experimental data agree well with the numerical values computed from the theoretical and empirical equations.

  12. Long-term Hg pollution induced Hg tolerance in the terrestrial isopod Porcellio scaber (Isopoda, Crustacea)

    Energy Technology Data Exchange (ETDEWEB)

    Lapanje, A. [University of Ljubljana, Biotechnical Faculty, Department of Biology, Vecna pot 111, 1000 Ljubljana (Slovenia); Institute of Physical Biology, Veliko Mlacevo 59, 1290 Grosuplje (Slovenia)], E-mail: ales.lapanje@bf.uni-lj.si; Drobne, D. [University of Ljubljana, Biotechnical Faculty, Department of Biology, Vecna pot 111, 1000 Ljubljana (Slovenia); Nolde, N. [Institute Jozef Stefan, Department of Environmental Sciences, Jamova 39, 1000 Ljubljana (Slovenia); Valant, J. [University of Ljubljana, Biotechnical Faculty, Department of Biology, Vecna pot 111, 1000 Ljubljana (Slovenia); Muscet, B. [Institute of Physical Biology, Veliko Mlacevo 59, 1290 Grosuplje (Slovenia); Leser, V. [University of Ljubljana, Biotechnical Faculty, Department of Biology, Vecna pot 111, 1000 Ljubljana (Slovenia); Rupnik, M. [Institute of Public Health, Prvomajska 1, 2000 Maribor (Slovenia); Faculty of Medicine, University of Maribor, Slomskov trg 15, 2000 Maribor (Slovenia)

    2008-06-15

    The aim of our work was to assess the pollution-induced community tolerance (PICT) of isopod gut microbiota and pollution-induced isopod population tolerance (PIPT). Animals collected from a chronically Hg polluted and an unpolluted location were exposed for 14 days to 10 {mu}g Hg/g dry food under laboratory conditions. The lysosomal membrane stability, hepatopancreas epithelium thickness, feeding activity and animal bacterial gut microbiota composition were determined. The results confirm the hypothesis that the response to short-term Hg exposure differs for animals from the Hg polluted and the unpolluted field locations. The animals and their gut microbiota from the Hg polluted location were less affected by Hg in a short-term feeding experiment than those from the unpolluted environment. We discuss the pollution-induced population tolerance of isopods and their gut microbiota as a measure of effects of long-term environmental pollution. The ecological consequences of such phenomena are also discussed. - Isopods (Porcellio scaber) as well as their bacterial gut community from a mercury-polluted site are mercury tolerant.

  13. MBE HgCdTe heterostructure detectors

    Science.gov (United States)

    Schulman, Joel N.; Wu, Owen K.

    1990-01-01

    HgCdTe has been the mainstay for medium (3 to 5 micron) and long (10 to 14 micron) wavelength infrared detectors in recent years. Conventional growth and processing techniques are continuing to improve the material. However, the additional ability to tailor composition and placement of doped layers on the tens of angstroms scale using molecular beam epitaxy (MBE) provides the opportunity for new device physics and concepts to be utilized. MBE-based device structures to be discussed here can be grouped into two categories: tailored conventional structures and quantum structures. The tailored conventional structures are improvements on familiar devices, but make use of the ability to create layers of varying composition, and thus band gap, at will. The heterostructure junction can be positioned independently of doping p-n junctions. This allows the small band gap region in which the absorption occurs to be separated from a larger band gap region in which the electric field is large and where unwanted tunneling can occur. Data from hybrid MBE/liquid phase epitaxy (LPE)/bulk structures are given. Quantum structures include the HgTe-CdTe superlattice, in which the band gap and transport can be controlled by alternating thin layers (tens of angstroms thick) of HgTe and CdTe. The superlattice has been shown to exhibit behavior which is non-alloy like, including very high hole mobilities, two-dimensional structure in the absorption coefficient, resonant tunneling, and anisotropic transport.

  14. The Seasonal Cycle of Water Vapour on Mars from Assimilation of Thermal Emission Spectrometer Data

    Science.gov (United States)

    Steele, Liam J.; Lewis, Stephen R.; Patel, Manish R.; Montmessin, Franck; Forget, Francois; Smith, Michael D.

    2014-01-01

    We present for the first time an assimilation of Thermal Emission Spectrometer (TES) water vapour column data into a Mars global climate model (MGCM). We discuss the seasonal cycle of water vapour, the processes responsible for the observed water vapour distribution, and the cross-hemispheric water transport. The assimilation scheme is shown to be robust in producing consistent reanalyses, and the global water vapour column error is reduced to around 2-4 pr micron depending on season. Wave activity is shown to play an important role in the water vapour distribution, with topographically steered flows around the Hellas and Argyre basins acting to increase transport in these regions in all seasons. At high northern latitudes, zonal wavenumber 1 and 2 stationary waves during northern summer are responsible for spreading the sublimed water vapour away from the pole. Transport by the zonal wavenumber 2 waves occurs primarily to the west of Tharsis and Arabia Terra and, combined with the effects of western boundary currents, this leads to peak water vapour column abundances here as observed by numerous spacecraft. A net transport of water to the northern hemisphere over the course of one Mars year is calculated, primarily because of the large northwards flux of water vapour which occurs during the local dust storm around L(sub S) = 240-260deg. Finally, outlying frost deposits that surround the north polar cap are shown to be important in creating the peak water vapour column abundances observed during northern summer.

  15. Ethanol vapour sensing properties of screen printed WO3 thick films

    Indian Academy of Sciences (India)

    R S Khadayate; R B Waghulde; M G Wankhede; J V Sali; P P Patil

    2007-04-01

    This paper presents ethanol vapour sensing properties of WO3 thick films. In this work, the WO3 thick films were prepared by standard screen-printing method. These films were characterized by X-ray diffraction (XRD) measurements and scanning electron microscopy (SEM). The ethanol vapour sensing properties of these thick films were investigated at different operating temperatures and ethanol vapour concentrations. The WO3 thick films exhibit excellent ethanol vapour sensing properties with a maximum sensitivity of ∼1424.6% at 400°C in air atmosphere with fast response and recovery time.

  16. Capillary microextraction: A new method for sampling methamphetamine vapour.

    Science.gov (United States)

    Nair, M V; Miskelly, G M

    2016-11-01

    Clandestine laboratories pose a serious health risk to first responders, investigators, decontamination companies, and the public who may be inadvertently exposed to methamphetamine and other chemicals used in its manufacture. Therefore there is an urgent need for reliable methods to detect and measure methamphetamine at such sites. The most common method for determining methamphetamine contamination at former clandestine laboratory sites is selected surface wipe sampling, followed by analysis with gas chromatography-mass spectrometry (GC-MS). We are investigating the use of sampling for methamphetamine vapour to complement such wipe sampling. In this study, we report the use of capillary microextraction (CME) devices for sampling airborne methamphetamine, and compare their sampling efficiency with a previously reported dynamic SPME method. The CME devices consisted of PDMS-coated glass filter strips inside a glass tube. The devices were used to dynamically sample methamphetamine vapour in the range of 0.42-4.2μgm(-3), generated by a custom-built vapour dosing system, for 1-15min, and methamphetamine was analysed using a GC-MS fitted with a ChromatoProbe thermal desorption unit. The devices showed good reproducibility (RSDsampling times and peak area, which can be utilised for calibration. Under identical sampling conditions, the CME devices were approximately 30 times more sensitive than the dynamic SPME method. The CME devices could be stored for up to 3days after sampling prior to analysis. Consecutive sampling of methamphetamine and its isotopic substitute, d-9 methamphetamine showed no competitive displacement. This suggests that CME devices, pre-loaded with an internal standard, could be a feasible method for sampling airborne methamphetamine at former clandestine laboratories. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

  17. Silicon nanowire arrays as learning chemical vapour classifiers

    Energy Technology Data Exchange (ETDEWEB)

    Niskanen, A O; Colli, A; White, R; Li, H W; Spigone, E; Kivioja, J M, E-mail: antti.niskanen@nokia.com [Nokia Research Center, Broers Building, 21 JJ Thomson Avenue, Cambridge CB3 0FA (United Kingdom)

    2011-07-22

    Nanowire field-effect transistors are a promising class of devices for various sensing applications. Apart from detecting individual chemical or biological analytes, it is especially interesting to use multiple selective sensors to look at their collective response in order to perform classification into predetermined categories. We show that non-functionalised silicon nanowire arrays can be used to robustly classify different chemical vapours using simple statistical machine learning methods. We were able to distinguish between acetone, ethanol and water with 100% accuracy while methanol, ethanol and 2-propanol were classified with 96% accuracy in ambient conditions.

  18. Chemical vapour deposited diamonds for dosimetry of radiotherapeutical beams

    Energy Technology Data Exchange (ETDEWEB)

    Bucciolini, M.; Mazzocchi, S. [Firenze Univ., Firenze (Italy). Dipartimento di Fisiopatologia Clinica; INFN, Firenze (Italy); Borchi, E.; Bruzzi, M.; Pini, S.; Sciortino, S. [Firenze Univ., Firenze (Italy). Dipartimento di Energetica; INFN, Firenze (Italy); Cirrone, G.A.P.; Guttone, G.; Raffaele, L.; Sabini, M.G. [INFN, Catania (Italy). Laboratori Nazionali del Sud

    2002-07-01

    This paper deals with the application of synthetic diamond detectors to the clinical dosimetry of photon and electron beams. It has been developed in the frame of INFN CANDIDO project and MURST Cofin. Diamonds grown with CVD (Chemical Vapour Deposition) technique have been studied; some of them are commercial samples while others have been locally synthesised. Experiments have been formed using both on-line and off-line approaches. For the off-line measurements, TL (thermoluminescent) and TSC (thermally stimulated current) techniques have been used.

  19. Electron and proton elastic scattering in water vapour

    Energy Technology Data Exchange (ETDEWEB)

    Champion, C., E-mail: champion@univ-metz.fr [Universite Paul Verlaine-Metz, Laboratoire de Physique Moleculaire et des Collisions, 1 Boulevard Arago, Technopole 2000, 57078 Metz (France); Universite Bordeaux 1, CNRS/IN2P3, Centre d' Etudes Nucleaires de Bordeaux Gradignan, CENBG, Chemin du Solarium, BP120, 33175 Gradignan (France); Incerti, S.; Tran, H.N. [Universite Bordeaux 1, CNRS/IN2P3, Centre d' Etudes Nucleaires de Bordeaux Gradignan, CENBG, Chemin du Solarium, BP120, 33175 Gradignan (France); El Bitar, Z. [Institut Pluridisciplinaire Hubert Curien, 23 rue du Loess, BP28, 67037 Strasbourg, Cedex 2 (France)

    2012-02-15

    In the present work, we report theoretical differential and integrated cross sections of the elastic scattering process for sub-thermalization electrons (E{sub inc} {approx_equal} 10 meV-10 keV) and 1 keV-1 MeV protons in water vapour. The calculations are performed within the quantum mechanical framework for electrons whereas classical calculations are provided for protons. The results obtained in this free-parameter theoretical treatment are compared to available data and quantitative differences are reported.

  20. Combined Dial Sounding of Ozone, Water Vapour and Aerosol

    Science.gov (United States)

    Trickl, Thomas; Vogelmann, Hannes

    2016-06-01

    Routine high-quality lidar measurements of ozone, water vapour and aerosol at Garmisch-Partenkirchen since 2007 have made possible more comprehensive atmospheric studies and lead to a growing insight concerning the most frequently occurring long-range transport pathways. In this contribution we present as examples results on stratospheric layers travelling in the free troposphere for extended periods of time without eroding. In particular, we present a case of an intrusion layer that subsided over as many as fifteen days and survived the interference by strong Canadian fires. These results impose a challenge on atmospheric modelling that grossly overestimates free-tropospheric mixing.

  1. Combined Dial Sounding of Ozone, Water Vapour and Aerosol

    Directory of Open Access Journals (Sweden)

    Trickl Thomas

    2016-01-01

    Full Text Available Routine high-quality lidar measurements of ozone, water vapour and aerosol at Garmisch-Partenkirchen since 2007 have made possible more comprehensive atmospheric studies and lead to a growing insight concerning the most frequently occurring long-range transport pathways. In this contribution we present as examples results on stratospheric layers travelling in the free troposphere for extended periods of time without eroding. In particular, we present a case of an intrusion layer that subsided over as many as fifteen days and survived the interference by strong Canadian fires. These results impose a challenge on atmospheric modelling that grossly overestimates free-tropospheric mixing.

  2. Long-distance transport of Hg, Sb, and As from a mined area, conversion of Hg to methyl-Hg, and uptake of Hg by fish on the Tiber River basin, west-central Italy

    Science.gov (United States)

    Gray, John E.; Rimondi, Valentina; Costagliola, Pilario; Vaselli, Orlando; Lattanzi, Pierfranco

    2014-01-01

    Stream sediment, stream water, and fish were collected from a broad region to evaluate downstream transport and dispersion of mercury (Hg) from inactive mines in the Monte Amiata Hg District (MAMD), Tuscany, Italy. Stream sediment samples ranged in Hg concentration from 20 to 1,900 ng/g, and only 5 of the 17 collected samples exceeded the probable effect concentration for Hg of 1,060 ng/g, above which harmful effects are likely to be observed in sediment-dwelling organisms. Concentrations of methyl-Hg in Tiber River sediment varied from 0.12 to 0.52 ng/g, and although there is no established guideline for sediment methyl-Hg, these concentrations exceeded methyl-Hg in a regional baseline site (Sb (Sb) and for protection against chronic effects to aquatic wildlife (150 μg/L for As and 5.6 μg/L for Sb). Concentrations of Hg in freshwater fish muscle ranged from 0.052–0.56 μg/g (wet weight), mean of 0.17 μg/g, but only 17 % (9 of 54) exceeded the 0.30 μg/g (wet weight) USEPA fish muscle guideline recommended to protect human health. Concentrations of Hg in freshwater fish in this region generally decreased with increasing distance from the MAMD, where fish with the highest Hg concentrations were collected more proximal to the MAMD, whereas all fish collected most distal from Hg mines contained Hg below the 0.30 μg/g fish muscle guideline. Data in this study indicate some conversion of inorganic Hg to methyl-Hg and uptake of Hg in fish on the Paglia River, but less methylation of Hg and Hg uptake by freshwater fish in the larger Tiber River.

  3. Hg Vetical Transference in Soil—Water System

    Institute of Scientific and Technical Information of China (English)

    GUOYIJUN; MOUSUSEN; 等

    1998-01-01

    Hg vertial transference in soil-water system was studied by analyzing Hg vertical ditribution in soil column after adding Hg and one of the two leacheates,deionzied water or acid rain,into soil column.The results indicated that Hg was hardly transferable in puple soil.About 86%-88% of the total soil Hg was distributed in the top layer (0-2cm) and to Hg was detected in the leakage when the purple soil column was leached by deionized water and simulated acid rain.But Hg was more movalbe in yellow soil with only about 20%-22% of the total soil Hg distributed in the top layer (0-2cm),and about 17%-25% washed out from the soil column by deionized water and simulted acid rain,Incremant in soil bulk density colud reduce Hg leaching,thus the more the Hg kept in soil,the less the Hg leached into underground water,Deionized water and acid rain almost played the same role in leaching Hg.Bentioint was most effecient in preventing Hg from vertcal transferring in the soil coulumn.

  4. Cytotoxicity of dental composite (co)monomers and the amalgam component Hg(2+) in human gingival fibroblasts.

    Science.gov (United States)

    Reichl, Franz-Xaver; Simon, Sabine; Esters, Magalie; Seiss, Mario; Kehe, Kai; Kleinsasser, Norbert; Hickel, Reinhard

    2006-08-01

    Unpolymerized resin (co)monomers or mercury (Hg) can be released from restorative dental materials (e.g. composites and amalgam). They can diffuse into the tooth pulp or the gingiva. They can also reach the gingiva and organs by the circulating blood after the uptake from swallowed saliva. The cytotoxicity of dental composite components hydroxyethylmethacrylate (HEMA), triethyleneglycoldimethacrylate (TEGDMA), urethanedimethacrylate (UDMA), and bisglycidylmethacrylate (Bis-GMA) as well as the amalgam component Hg(2+) (as HgCl(2)) and methyl mercury chloride (MeHgCl) was investigated on human gingival fibroblasts (HGFs) at two time intervals. To test the cytotoxicity of substances, the bromodeoxyuridine (BrdU) assay and the lactate dehydrogenase (LDH) assay were used. The test substances were added in various concentrations and cells were incubated for 24 or 48 h. The EC(50) values were obtained as half-maximum-effect concentrations from fitted curves. Following EC(50) values were found [BrdU: mean (mmol/l); SEM in parentheses; n=12]: (24 h/48 h) HEMA 8.860 (0.440)/6.600(0.630), TEGDMA 1.810(0.130)/1.220(0.130), UDMA 0.120(0.010)/0.140(0.010), BisGMA 0.060(0.004)/0.040(0.002), HgCl(2) 0.015(0.001)/0.050(0.006), and MeHgCl 0.004(0.001)/0.005(0.001). Following EC(50) values were found [LDH: mean (mmol/l); SEM in parentheses; n=12]: (24 h/48 h) HEMA 9.490(0.300)/7.890(1.230), TEGDMA 2.300(0.470)/1.950(0.310), UDMA 0.200(0.007)/0.100(0.007), BisGMA 0.070(0.005)/0.100(0.002), and MeHgCl 0.014(0.006)/0.010(0.003). In both assays, the following range of increased toxicity was found for composite components (24 and 48 h): HEMA < TEGDMA < UDMA < BisGMA. In both assays, MeHgCl was the most toxic substance. In the BrdU assay, Hg(2+) was about fourfold less toxic than MeHgCl but Hg(2+) was about fourfold more toxic than BisGMA. In the BrdU test, a significantly (P<0.05) decreased toxicity was observed for Hg(2+) at 48 h, compared to the 24 h Hg(2+)-exposure. A time depending

  5. Antimicrobial action of essential oil vapours and negative air ions against Pseudomonas fluorescens.

    Science.gov (United States)

    Tyagi, A K; Malik, A

    2010-10-15

    The aim of this study was to investigate the antibacterial activity of essential oil (in liquid as well as in vapour phase) and negative air ions (NAI) against Pseudomonas fluorescens. The combined effect of NAI with essential oil vapour was also investigated to determine kill time and morphological changes in bacterial cells. The MIC of Cymbopogon citratus (0.567 mg/ml), Mentha arvensis (0.567 mg/ml), Mentha piperita (1.125 mg/ml) and Eucalyptus globulus (2.25 mg/ml) was studied via the agar dilution method. To estimate the antibacterial activity of essential oils in the vapour phase, agar plates inoculated with P. fluorescens were incubated with various concentrations of each essential oil vapour and zone of inhibition was recorded. Further, in order to assess the kill time, P. fluorescens inoculated agar plates were exposed to selected bactericidal essential oil vapour and NAI, separately, in an air-tight chamber. A continuous decrease in bacterial count was observed over time. A significant enhancement in the bactericidal action was observed by exposure to the combination of essential oil vapour and NAI as compared to their individual action. Scanning electron microscopy was used to study the alteration in morphology of P. fluorescens cells after exposure to C. citratus oil vapour, NAI, and combination of C. citratus oil vapour and NAI. Maximum morphological deformation was found due to the combined effect of C. citratus oil vapour and NAI. This study demonstrates that the use of essential oils in the vapour phase is more advantageous than the liquid phase. Further the antibacterial effect of the essential oil vapours can be significantly enhanced by the addition of NAI. The work described here offers a novel and efficient approach for control of bacterial contamination that could be applied for food stabilization practices. Copyright © 2010 Elsevier B.V. All rights reserved.

  6. Electrical properties of solid iodo mercurates resulting from the reaction of HgI2 with alcaline iodides

    Science.gov (United States)

    Ponpon, J. P.; Amann, M.

    2005-01-01

    Potassium iodide solutions are currently used during the fabrication process of mercuric iodide based nuclear radiation detectors. However, KI treatment leaves the HgI2 surface covered with a residual compound (namely the potassium tri-iodo mercurate) which has a significant influence on the surface properties and stability of mercuric iodide devices and therefore on the detectors characteristics. Looking for other solutions to etch mercuric iodide, we found it interesting to investigate the electrical properties of the compounds which may form when etching HgI2 in NH4I, NaI, and RbI. For this purpose, solid iodo mercurates with the cations ammonium, sodium, and rubidium, have been prepared by reacting HgI2 with the solutions of interest. Study of the electrical properties of these samples and comparison with those of potassium tri-iodo mercurate ones, especially with respect to humidity, indicates noticeable stability differences in presence of water vapour. This could have interesting consequences on the surface cleaning of mercuric iodide.

  7. Pulmonary CT findings in acute mercury vapour exposure

    Energy Technology Data Exchange (ETDEWEB)

    Hashimoto, Manabu; Sato, Kimihiko; Heianna, Jyouiti; Hirano, Yoshinori; Omachi, Kohiti; Izumi, Jyunichi; Watarai, Jiro

    2001-01-01

    AIM: We describe the pulmonary computed tomography (CT) findings in acute mercury poisoning. MATERIALS AND METHODS: Initial (n= 8) and follow-up (n= 6) chest CT examinations in eight patients exposed to mercury vapour while cutting pipes in a sulphuric acid plant were reviewed. Of the eight patients, two were asymptomatic and had normal CT results, two were asymptomatic but had abnormalities on CT, and four had both acute symptoms and positive CT results. The patients were all men whose ages ranged from 37 to 54 years (mean, 49 years). RESULTS: Poorly defined nodules were present in five of six patients with positive CT findings, present alone in two patients or as part of a mixed pattern in three. They were random in distribution. Alveolar consolidation (n= 3) and areas of ground-glass opacity (n= 4) were observed and were more prominent in the most severely affected patients with the highest blood and urine level of mercury, predominantly in the upper and/or middle zone. These abnormal findings on CT resolved with (n= 1) or without (n= 5) steroid therapy. Pathological findings (n= 1) demonstrated acute interstitial changes predominantly with oedema. CONCLUSION: We report CT findings in eight patients acutely exposed to mercury vapour. The pulmonary injury was reversible on CT in these cases. Hashimoto, M. (2001)

  8. All-sky homogeneity of precipitable water vapour over Paranal

    CERN Document Server

    Querel, Richard R

    2014-01-01

    A Low Humidity and Temperature Profiling (LHATPRO) microwave radiometer, manufactured by Radiometer Physics GmbH (RPG), is used to monitor sky conditions over ESO's Paranal observatory in support of VLT science operations. The unit measures several channels across the strong water vapour emission line at 183 GHz, necessary for resolving the low levels of precipitable water vapour (PWV) that are prevalent on Paranal (median ~2.4 mm). The instrument consists of a humidity profiler (183-191 GHz), a temperature profiler (51-58 GHz), and an infrared camera (~10 {\\mu}m) for cloud detection. We present, for the first time, a statistical analysis of the homogeneity of all-sky PWV using 21 months of periodic (every 6 hours) all-sky scans from the radiometer. These data provide unique insight into the spatial and temporal variation of atmospheric conditions relevant for astronomical observations, particularly in the infrared. We find the PWV over Paranal to be remarkably homogeneous across the sky down to 27.5{\\deg} el...

  9. Charge Transport in Polyaniline and Vapour Induced Structural Changes

    Science.gov (United States)

    Minto, C. D. G.; Vaughan, A. S.

    1996-03-01

    Camphor sulphonic acid protonation renders polyaniline soluble in both m-cresol and chloroform. Films cast from these solvents exhibit vastly differing transport properties. m-cresol cast films are metallic or lie on the metal/insulator transition, whereas those cast from chloroform are insulators. Similarly pellets of pressed doped polyaniline powder exhibit insulating characteristics. We present an investigation of such effects in polyaniline obtained from both insulating conditions (films and powders). We find that m-cresol -- vapour treatment of these materials causes a rapid increase both in the conductivity and the type of conduction, changing from an insulator to a material approaching the metal/insulator transition. Chloroform films actually take on characteristics of those cast from m-cresol, including a positive temperature coefficient of resistivity. Both starting materials exhibit similar X-ray scattering patterns, after exposure to vapour, the pattern becomes more similar to that which is found in m-cresol cast films. Conformational changes resulting from a strong polymer--interaction are discussed as the motivation for the improvements in transport properties.

  10. Diffusion of Implanted Radioisotopes in Solids

    CERN Multimedia

    2002-01-01

    Implantation of radioisotopes into metal and semiconductor samples is performed. The implanted isotope or its decay-product should have a half-life long enough for radiotracer diffusion experiments. Such radioisotopes are utilized to investigate basic diffusion properties in semiconductors and metals and to improve our understanding of the atomic mechanisms of diffusion. For suitably chosen systems the combination of on-line production and clean implantation of radioisotopes at the ISOLDE facility opens new possibilities for diffusion studies in solids. \\\\ \\\\ The investigations are concentrated on diffusion studies of $^{195}$Au in amorphous materials. The isotope $^{195}$Au was obtained from the mass 195 of the mercury beam. $^{195}$Hg decays into $^{195}$Au which is a very convenient isotope for diffusion experiments. \\\\ \\\\ It was found that $^{195}$Au is a slow diffusor in amorphous Co-Zr alloys, whereas Co is a fast diffusor in the same matrix. The ``asymmetry'' in the diffusion behaviour is of considerab...

  11. Process of [sup 196]Hg enrichment

    Science.gov (United States)

    Grossman, M.W.; Mellor, C.E.

    1993-04-27

    A simple rate equation model shows that by increasing the length of the photochemical reactor and/or by increasing the photon intensity in said reactor, the feedstock utilization of [sup 196]Hg will be increased. Two preferred embodiments of the present invention are described, namely (1) long reactors using long photochemical lamps and vapor filters; and (2) quartz reactors with external UV reflecting films. These embodiments have each been constructed and operated, demonstrating the enhanced utilization process dictated by the mathematical model (also provided).

  12. Process of .sup.196 Hg enrichment

    Science.gov (United States)

    Grossman, Mark W.; Mellor, Charles E.

    1993-01-01

    A simple rate equation model shows that by increasing the length of the photochemical reactor and/or by increasing the photon intensity in said reactor, the feedstock utilization of .sup.196 Hg will be increased. Two preferred embodiments of the present invention are described, namely (1) long reactors using long photochemical lamps and vapor filters; and (2) quartz reactors with external UV reflecting films. These embodiments have each been constructed and operated, demonstrating the enhanced utilization process dictated by the mathematical model (also provided).

  13. Magnetic fields of HgMn stars

    DEFF Research Database (Denmark)

    Hubrig, S.; González, J. F.; Ilyin, I.

    2012-01-01

    Context. The frequent presence of weak magnetic fields on the surface of spotted late-B stars with HgMn peculiarity in binary systems has been controversial during the two last decades. Recent studies of magnetic fields in these stars using the least-squares deconvolution (LSD) technique have...... failed to detect magnetic fields, indicating an upper limit on the longitudinal field between 8 and 15G. In these LSD studies, assumptions were made that all spectral lines are identical in shape and can be described by a scaled mean profile. Aims. We re-analyse the available spectropolarimetric material...

  14. Of Variability, or its Absence, in HgMn Stars

    CERN Document Server

    Turcotte, S

    2003-01-01

    Current models and observations of variability in HgMn stars disagree. We present here the models that argue for pulsating HgMn stars with properties similar to those of Slowly Pulsating B Stars. The lack of observed variable HgMn stars suggests that some physical process is missing from the models. Some possibilities are discussed.

  15. Vapour phase alkylation of ethylbenzene with -butyl alcohol over mesoporous Al-MCM-41 molecular sieves

    Indian Academy of Sciences (India)

    V Umamaheswari; M Palanichamy; Banumathi Arabindoo; V Murugesan

    2002-06-01

    The alkylation of ethylbenzene with -butyl alcohol was studied over Al-MCM-41 (Si/Al = 50 and 90) and Al, Mg-MCM-41 (Si/(Al + Mg) =50) in the vapour phase from 200 to 400°C. The products were --butylethylbenzene (--BEB), --butylvinylbenzene (--BVB) and --butylethylbenzene ( --BEB). Ethylbenzene conversion decreased with increase in temperature and increase in the ethylbenzene content of the feed. The reaction between the freely diffusing ethylbenzene in the channel and the -butyl cations remaining as charge compensating ions yielded --BEB. --BVB, an unexpected product in this investigation, was produced by dehydrogenation of --BEB over alumina particles present in the channels of the molecular sieves. Adsorption of ethylbenzene on Brønsted acid sites and its subsequent reaction with very closely adsorbed -butyl cations proved to be necessary to obtain --BEB. Though --BEB was obtained, the corresponding --butylvinylbenzene was not observed in this study. Study of time durations indicated rapid and slow catalyst deactivation at lower and higher streams respectively.

  16. Vapour phase dehydration of glycerol to acrolein over tungstated zirconia catalysts

    Science.gov (United States)

    Rao Ginjupalli, Srinivasa; Mugawar, Sowmya; Rajan N., Pethan; Kumar Balla, Putra; Chary Komandur, V. R.

    2014-08-01

    Tetragonal (TZ) and monoclinic (MZ) polymorphs of zirconia supports were synthesised by sol-gel method followed by variation of the calcination temperature. Tungstated (10 wt% WO3) supported on the zirconia polymorphs were prepared by impregnation method by using ammonium metatungstate precursor. The physico-chemical properties of the calcined catalysts were characterised by X-ray diffraction, UV-vis diffused reflectance spectroscopy, X-ray photoelectron spectroscopy (XPS), surface area and pore size distribution measurements to gain insight into the effect of morphology of the catalyst textural properties, and structure. The surface acidic properties have been determined by NH3 TPD method and also with FT-IR spectra of pyridine adsorption. Vapour phase dehydration of glycerol to acrolein was employed to investigate the catalytic functionalities. Glycerol conversion and acrolein selectivity was mainly dependent on the fraction of moderate acid sites with majority of them are due to Brønsted acidic sites. Monoclinic zirconia based catalysts have shown the highest activity and acrolein selectivity compared to the corresponding tetragonal zirconia catalysts.

  17. Vapour phase dehydration of glycerol to acrolein over tungstated zirconia catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Rao Ginjupalli, Srinivasa; Mugawar, Sowmya; Rajan, Pethan N.; Kumar Balla, Putra; Chary Komandur, V.R., E-mail: kvrchary@iict.res.in

    2014-08-01

    Tetragonal (TZ) and monoclinic (MZ) polymorphs of zirconia supports were synthesised by sol–gel method followed by variation of the calcination temperature. Tungstated (10 wt% WO{sub 3}) supported on the zirconia polymorphs were prepared by impregnation method by using ammonium metatungstate precursor. The physico-chemical properties of the calcined catalysts were characterised by X-ray diffraction, UV–vis diffused reflectance spectroscopy, X-ray photoelectron spectroscopy (XPS), surface area and pore size distribution measurements to gain insight into the effect of morphology of the catalyst textural properties, and structure. The surface acidic properties have been determined by NH{sub 3} TPD method and also with FT-IR spectra of pyridine adsorption. Vapour phase dehydration of glycerol to acrolein was employed to investigate the catalytic functionalities. Glycerol conversion and acrolein selectivity was mainly dependent on the fraction of moderate acid sites with majority of them are due to Brønsted acidic sites. Monoclinic zirconia based catalysts have shown the highest activity and acrolein selectivity compared to the corresponding tetragonal zirconia catalysts.

  18. Liquid-vapour equilibrium in the restricted primitive model for ionic liquids

    Science.gov (United States)

    Gillan, M. J.

    We study the thermodynamic equilibrium between liquid and vapour for the restricted primitive model (charged hard spheres of equal diameters) of a two component ionic liquid. We point out that physical clustering of ions will have a crucial effect on this equilibrium. The calculations presented are based on the representation of the vapour as a mixture of clusters of different types, the interactions between clusters being neglected. The relative proportions of the different types are governed by the law of mass action. We show that neglect of interactions yields a lower bound to the true vapour pressure. The internal free energies of the clusters in the vapour are obtained from a combination of analytic and Monte Carlo calculations and the thermodynamic properties of the liquid phase are derived from Larsen's published Monte Carlo results. We present numerical results for the densities of different cluster types in the vapour phase, for the overall liquid and vapour densities and for the vapour pressure. A comparison with the predictions of the mean spherical approximation and of Larsen's empirical equation show that these yield vapour pressures which are far below our lower bound and are therefore erroneous. We point out that Larsen's equation implies a weak subsidiary critical point on the liquid branch of the coexistence curve, an effect which we suggest is spurious. Finally, we discuss the relation between our work and that of Stell, Wu and Larsen.

  19. New Method of Vapour Discrimination Using the Thickness Shear Mode (TSM Resonator

    Directory of Open Access Journals (Sweden)

    J. Siddiqi

    2003-06-01

    Full Text Available The Impedance analysis technique complimented with curve fitting software was used to monitor changes in film properties of Thickness Shear Mode (TSM resonator on vapour exposure. The approach demonstrates how sensor selectivity can be achieved through unique changes in film viscosity caused by organic vapour adsorption.

  20. Diffusion MRI

    Science.gov (United States)

    Fukuyama, Hidenao

    Recent advances of magnetic resonance imaging have been described, especially stressed on the diffusion sequences. We have recently applied the diffusion sequence to functional brain imaging, and found the appropriate results. In addition to the neurosciences fields, diffusion weighted images have improved the accuracies of clinical diagnosis depending upon magnetic resonance images in stroke as well as inflammations.

  1. Condensation of water vapour on moss-dominated biological soil crust, NW China

    Indian Academy of Sciences (India)

    Xin-Ping Wang; Yan-Xia Pan; Rui Hu; Ya-Feng Zhang; Hao Zhang

    2014-03-01

    Characteristics of water vapour condensation, including the onset, duration, and amount of water vapour condensation on moss-dominated biological soil crust (BSC) and dune sand were studied under simulated conditions with varying air temperature and relative humidity. The simulations were performed in a plant growth chamber using an electronic balance recording the weight of condensation. There was a positive linear correlation between the water vapour condensation and relative humidity while the mean temperature was negatively linearly related to amounts of water vapour condensation for both soil surfaces. The amount of water vapour condensation on BSC and dune sand can be described by the difference between air temperature and dew point with an exponential function, indicating that when the difference of air temperature and dew point exceeds a value of 35.3°C, there will be zero water vapour condensed on BSC. In contrast, when the difference of air temperature and dew point exceeds a value of 20.4°C, the water vapour condensation will be zero for dune sand. In general, when the air is fully saturated with water and the dew point is equal to the current air temperature, the water vapour condensed on BSC attained its maximum value of 0.398 mm, whereas it was 0.058 mm for dune sand. In comparison, water vapour condensed on BSC was at a relatively high temperature and low relative humidity, while we did not detect water vapour condensation on the dune sand under the similar conditions. Physical and chemical analyses of the samples pointed to a greater porosity, high content of fine particles, and high salinity for BSC compared to the dune sand. These results highlight that soil physicochemical properties are the likely factors influencing the mechanism of water vapour condensation under specific meteorological conditions, as onset was earlier and the duration was longer for water vapour condensation on BSC in comparison with that of dune sand. This contributed to

  2. Condensation of water vapour on moss-dominated biological soil crust, NW China

    Science.gov (United States)

    Wang, Xin-Ping; Pan, Yan-Xia; Hu, Rui; Zhang, Ya-Feng; Zhang, Hao

    2014-03-01

    Characteristics of water vapour condensation, including the onset, duration, and amount of water vapour condensation on moss-dominated biological soil crust (BSC) and dune sand were studied under simulated conditions with varying air temperature and relative humidity. The simulations were performed in a plant growth chamber using an electronic balance recording the weight of condensation. There was a positive linear correlation between the water vapour condensation and relative humidity while the mean temperature was negatively linearly related to amounts of water vapour condensation for both soil surfaces. The amount of water vapour condensation on BSC and dune sand can be described by the difference between air temperature and dew point with an exponential function, indicating that when the difference of air temperature and dew point exceeds a value of 35.3◦C, there will be zero water vapour condensed on BSC. In contrast, when the difference of air temperature and dew point exceeds a value of 20.4◦C, the water vapour condensation will be zero for dune sand. In general, when the air is fully saturated with water and the dew point is equal to the current air temperature, the water vapour condensed on BSC attained its maximum value of 0.398 mm, whereas it was 0.058 mm for dune sand. In comparison, water vapour condensed on BSC was at a relatively high temperature and low relative humidity, while we did not detect water vapour condensation on the dune sand under the similar conditions. Physical and chemical analyses of the samples pointed to a greater porosity, high content of fine particles, and high salinity for BSC compared to the dune sand. These results highlight that soil physicochemical properties are the likely factors influencing the mechanism of water vapour condensation under specific meteorological conditions, as onset was earlier and the duration was longer for water vapour condensation on BSC in comparison with that of dune sand. This contributed to

  3. Estimation of vapour pressure and partial pressure of subliming compounds by low-pressure thermogravimetry

    Indian Academy of Sciences (India)

    G V Kunte; Ujwala Ail; P K Ajikumar; A K Tyagi; S A Shivashankar; A M Umarji

    2011-12-01

    A method for the estimation of vapour pressure and partial pressure of subliming compounds under reduced pressure, using rising temperature thermogravimetry, is described in this paper. The method is based on our recently developed procedure to estimate the vapour pressure from ambient pressure thermogravimetric data using Langmuir equation. Using benzoic acid as the calibration standard, vapour pressure–temperature curves are calculated at 80, 160 and 1000 mbar for salicylic acid and vanadyl bis-2,4-pentanedionate, a precursor used for chemical vapour deposition of vanadium oxides. Using a modification of the Langmuir equation, the partial pressure of these materials at different total pressures is also determined as a function of temperature. Such data can be useful for the deposition of multi-metal oxide thin films or doped thin films by chemical vapour deposition (CVD).

  4. The Research on Atmospheric Pressure Water Vapour Plasma Generation and Application for the Destruction of Wastes

    Directory of Open Access Journals (Sweden)

    Viktorija Grigaitiene

    2013-01-01

    Full Text Available In the Lithuanian Energy Institute an experimental atmospheric pressure Ar/water vapour plasma torch has been designed and tested. The power of plasma torch was estimated 40 ÷ 69 kW, the mean temperature of plasma jet at the exhaust nozzle was 2300÷2900K. The chemical compositionof water vapour plasma was established from the emission spectrum lines at 300 ÷ 800nm range. The main species observed in Ar/water vapour plasma were: Ar, OH, H, O, Cu. The experiments on water vapour steam reforming were performed. The results confirmed that water vapour plasma has the unique properties – high enthalpy and environmentally friendly conditions. It could be employed for environmental purposes such as destruction of wastes into simple molecules or conversion to synthetic gas.

  5. Accuracy of the Water Vapour Content Measurements in the Atmosphere Using Optical Methods

    CERN Document Server

    Galkin, V D; Alekseeva, G A; Novikov, V V; Pakhomov, V P

    2010-01-01

    This paper describes the accuracy and the errors of water vapour content measurements in the atmosphere using optical methods, especially starphotometer. After the general explanations of the used expressions for the star-magnitude observations of the water vapour absorption in section 3 the absorption model for the water vapour band will be discussed. Sections 4 and 5 give an overview on the technique to determine the model parameters both from spectroscopic laboratory and radiosonde observation data. Finally, the sections 6 and 7 are dealing with the details of the errors; that means errors of observable magnitude, of instrumental extraterrestrial magnitude, of atmospheric extinction determination and of water vapour content determination by radiosonde humidity measurements. The main conclusion is: Because of the high precision of the results the optical methods for water vapour observation are suited to validate and calibrate alternative methods (GPS, LIDAR, MICROWAVE) which are making constant progress wo...

  6. HgZnTe-based detectors for LWIR NASA applications

    Science.gov (United States)

    Patten, Elizabeth A.; Kalisher, Murray H.

    1990-01-01

    The initial goal was to grow and characterize HgZnTe and determine if it indeed had the advantageous properties that were predicted. Researchers grew both bulk and liquid phase epitaxial HgZnTe. It was determined that HgZnTe had the following properties: (1) microhardness at least 50 percent greater than HgCdTe of equivalent bandgap; (2) Hg annealing rates of at least 2 to 4 times longer than HgCdTe; and (3) higher Hg vacancy formation energies. This early work did not focus on one specific composition (x-value) of HgZnTe since NASA was interested in HgZnTe's potential for a variety of applications. Since the beginning of 1989, researchers have been concentrating, however, on the liquid phase growth of very long wavelength infrared (VLWIR) HgZnTe (cutoff approx. equals 17 microns at 65K) to address the requirements of the Earth Observing System (EOS). Since there are no device models to predict the advantages in reliability one can gain with increased microhardness, surface stability, etc., one must fabricate HgZnTe detectors and assess their relative bake stability (accelerated life test behavior) compared with HgCdTe devices fabricated in the same manner. Researchers chose to fabricate HIT detectors as a development vehicle for this program because high performance in the VLWIR has been demonstrated with HgCdTe HIT detectors and the HgCdTe HIT process should be applicable to HgZnTe. HIT detectors have a significant advantage for satellite applications since these devices dissipate much less power than conventional photoconductors to achieve the same responsivity.

  7. Fully relativistic coupled cluster and DFT study of electric field gradients at Hg in 199Hg compounds

    DEFF Research Database (Denmark)

    Arcisauskaité, Vaida; Knecht, Stefan; Sauer, Stephan P. A.

    2012-01-01

    We investigate the magnitude and interplay of relativistic and electron correlation effects on the electric field gradient (EFG) at the position of Hg in linear and bent HgL2 (L=CH3, Cl, Br, I) and trigonal planar [HgCl3]- complexes using four-component relativistic Dirac-Coulomb (DC) and non...

  8. Gettering of interstitial iron in silicon by plasma-enhanced chemical vapour deposited silicon nitride films

    Science.gov (United States)

    Liu, A. Y.; Sun, C.; Markevich, V. P.; Peaker, A. R.; Murphy, J. D.; Macdonald, D.

    2016-11-01

    It is known that the interstitial iron concentration in silicon is reduced after annealing silicon wafers coated with plasma-enhanced chemical vapour deposited (PECVD) silicon nitride films. The underlying mechanism for the significant iron reduction has remained unclear and is investigated in this work. Secondary ion mass spectrometry (SIMS) depth profiling of iron is performed on annealed iron-contaminated single-crystalline silicon wafers passivated with PECVD silicon nitride films. SIMS measurements reveal a high concentration of iron uniformly distributed in the annealed silicon nitride films. This accumulation of iron in the silicon nitride film matches the interstitial iron loss in the silicon bulk. This finding conclusively shows that the interstitial iron is gettered by the silicon nitride films during annealing over a wide temperature range from 250 °C to 900 °C, via a segregation gettering effect. Further experimental evidence is presented to support this finding. Deep-level transient spectroscopy analysis shows that no new electrically active defects are formed in the silicon bulk after annealing iron-containing silicon with silicon nitride films, confirming that the interstitial iron loss is not due to a change in the chemical structure of iron related defects in the silicon bulk. In addition, once the annealed silicon nitride films are removed, subsequent high temperature processes do not result in any reappearance of iron. Finally, the experimentally measured iron decay kinetics are shown to agree with a model of iron diffusion to the surface gettering sites, indicating a diffusion-limited iron gettering process for temperatures below 700 °C. The gettering process is found to become reaction-limited at higher temperatures.

  9. The Chevrel phase HgMo6S8

    Directory of Open Access Journals (Sweden)

    Michel Potel

    2009-05-01

    Full Text Available The crystal structure of HgMo6S8, mercury(II hexamolybdenum octasulfide, is based on (Mo6S8S6 cluster units (overline{3} symmetry interconnected through interunit Mo—S bonds. The Hg2+ cations occupy large voids between the different cluster units and are covalently bonded to two S atoms. The Hg atoms and one S atom lie on sites with crystallographic overline{3} and 3 symmetry, respectively. Refinement of the occupancy factor of the Hg atom led to the composition Hg0.973 (3Mo6S8.

  10. Stratospheric water vapour as tracer for Vortex filamentation in the Arctic winter 2002/2003

    Directory of Open Access Journals (Sweden)

    M. Müller

    2003-01-01

    Full Text Available Balloon-borne frost point hygrometers measured three high-resolution profiles of stratospheric water vapour above Ny-Ålesund, Spitsbergen during winter 2002/2003. The profiles obtained on 12 December 2002 and on 17 January 2003 provide an insight into the vertical distribution of water vapour in the core of the polar vortex. The water vapour sounding on 11 February 2003 was obtained within the vortex edge region of the lower stratosphere. Here, a significant reduction of water vapour mixing ratio was observed between 16 and 19 km. The stratospheric temperatures indicate that this dehydration was not caused by the presence of polar stratospheric clouds or earlier PSC particle sedimentation. Ozone observations on this day indicate a large scale movement of the polar vortex and show laminae in the same altitude range as the water vapour profile. The link between the observed water vapour reduction and filaments in the vortex edge region is indicated in the results of the semi-lagrangian advection model MIMOSA, which show that adjacent filaments of polar and mid latitude air can be identified above the Spitsbergen region. A vertical cross-section produced by the MIMOSA model reveals that the water vapour sonde flew through polar air in the lowest part of the stratosphere below 425 K, then passed through filaments of mid latitude air with lower water vapour concentrations, before it finally entered the polar vortex above 450 K. These results indicate that on 11 February 2003 the frost point hygrometer measured different water vapour concentrations as the sonde detected air with different origins. Instead of being linked to dehydration due to PSC particle sedimentation, the local reduction in the stratospheric water vapour profile was in this case caused by dynamical processes in the polar stratosphere.

  11. Adsorption of Hg(II from Aqueous Solution Using Adulsa (Justicia adhatoda Leaves Powder: Kinetic and Equilibrium Studies

    Directory of Open Access Journals (Sweden)

    Mohd Aslam

    2013-01-01

    Full Text Available The ability of Adulsa leaves powder (ALP to adsorb Hg(II from aqueous solutions has been investigated through batch experiments. The ALP biomass was characterized by Fourier transform infrared spectroscopy and scanning electron microscopy. The experimental parameters that were investigated in this study included pH, adsorbent dosage, and effect of contact time along with initial metal ion concentration. The adsorption process was relatively fast, and equilibrium was achieved after 40 min of contact time. The maximum removal of Hg(II, 97.5% was observed at pH 6. The adsorption data were correlated with Langmuir, Freundlich, and Temkin isotherms. Isotherms results were amply fitted by the Langmuir model determining a monolayer maximum adsorption capacity (qm of ALP biomass equal to 107.5 mg g−1 and suggesting a functional group-limited sorption process. The kinetic process of Hg(II adsorption onto ALP biomass was tested by applying pseudofirst-order, pseudosecond-order, Elovich, and intraparticle-diffusion models to correlate the experimental data and to determine the kinetic parameters. It was found that the pseudosecond order kinetic model for Hg(II adsorption fitted very well. The rate determining step is described by intraparticle diffusion model. These studies considered the possibility of using Adulsa plant leaves biomass as an inexpensive, efficient, and environmentally safe adsorbent for the treatment of Hg(II contaminated wastewaters.

  12. Plasma Enhanced Chemical Vapour Deposition of Horizontally Aligned Carbon Nanotubes

    Directory of Open Access Journals (Sweden)

    Matthew T. Cole

    2013-05-01

    Full Text Available A plasma-enhanced chemical vapour deposition reactor has been developed to synthesis horizontally aligned carbon nanotubes. The width of the aligning sheath was modelled based on a collisionless, quasi-neutral, Child’s law ion sheath where these estimates were empirically validated by direct Langmuir probe measurements, thereby confirming the proposed reactors ability to extend the existing sheath fields by up to 7 mm. A 7 mbar growth atmosphere combined with a 25 W plasma permitted the concurrent growth and alignment of carbon nanotubes with electric fields of the order of 0.04 V μm−1 with linear packing densities of up to ~5 × 104 cm−1. These results open up the potential for multi-directional in situ alignment of carbon nanotubes providing one viable route to the fabrication of many novel optoelectronic devices.

  13. Fibre-optic UV systems for gas and vapour analysis

    Energy Technology Data Exchange (ETDEWEB)

    Eckhardt, H S [University of Applied Sciences Giessen-Friedberg, Wilhelm-Leuschner-Str, 13, 61169 Friedberg (Germany); Klein, K-F [University of Applied Sciences Giessen-Friedberg, Wilhelm-Leuschner-Str, 13, 61169 Friedberg (Germany); Spangenberg, B [University of Applied Sciences Offenburg, Badstrasse 24, 77652 Offenburg (Germany); Sun, T [City University London, Northampton Square, London, EC1V 0HB (United Kingdom); Grattan, K T V [City University London, Northampton Square, London, EC1V 0HB (United Kingdom)

    2007-10-15

    The identification and quantification of compounds in the gas phase becomes of increasing interest in the context of environmental protection, as well as in the analytical field. In this respect, the high extinction coefficients of vapours and gases in the ultraviolet wavelength region allow a very sensitive measurement system. In addition, the increased performance of the components necessary for setting up a measurement system, such as fibres, light sources and detectors has been improved. In particular the light sources and detectors offer improved stability, and the deep UV performance and solarisation resistance of fused silica fibres allow have been significantly optimized in the past years. Therefore a compact and reliable detection system with high measuring accuracy is developed. Within this paper possible applications of the system under development and recent results will be discussed.

  14. Impedimetric detection of alcohol vapours using nanostructured zinc ferrite.

    Science.gov (United States)

    Kannan, Padmanathan Karthick; Saraswathi, Ramiah

    2014-11-01

    A comparative study on the sensing characteristics of nanostructured zinc ferrite to three primary alcohols viz. methanol, ethanol and propanol has been carried out. The zinc ferrite has been prepared by a combustion method and characterized by XRD, FTIR, AFM and SEM. Impedance studies in the alcohol concentration range varying from 100 to 1000 ppm show definite variations in response to both the nature of the alcohol and its concentration. The nanostructured zinc ferrite shows the highest sensor response to methanol and least to propanol. Equivalent circuit modelling and calibration have been made for all the three alcohol sensors. The material shows a better selectivity to the alcohols compared to formaldehyde, ammonia and acetone vapours.

  15. The Chemical Vapour Deposition of Tantalum - in long narrow channels

    DEFF Research Database (Denmark)

    Mugabi, James Atwoki

    use as a construction material for process equipment, with the cheaper alternative being the construction of equipment from steel and then protecting it with a thin but efficacious layer of tantalum. Chemical Vapour Deposition (CVD) is chosen as the most effective process to apply thin corrosion...... protective layers of tantalum because of the process’ ability to coat complex geometries and its relative ease to control. This work focuses on studying the CVD of tantalum in long narrow channels with the view that the knowledge gained during the project can be used to optimise the commercial coating...... process that Tantaline A/S and Alfa Laval (Sweden) use to manufacture tantalum coated plate heat exchangers. Experiments are done by coating the inner side of long, thin stainless steel tubes in the temperature range of 700 – 950 °C and pressure range of 25 – 990 mbar while using different reactant...

  16. Transport properties of polymer-vapour grown carbon fibre composites

    Science.gov (United States)

    Gordeyev, S. A.; Macedo, F. J.; Ferreira, J. A.; van Hattum, F. W. J.; Bernardo, C. A.

    2000-04-01

    DC electrical resistivity and thermal conductivity of polypropylene (PP) filled with vapour grown carbon fibre (VGCF) was studied. This was done for a wide range of fibre content and compared to systems produced under the same conditions in which a conventional carbon fibre was used as filler. The composites studied exhibit characteristic percolating behaviour. Because of the low degree of graphite perfection in the VGCF used in this work, the fraction of VGCF required to achieve percolation was higher than expected. Non-linear I- V characteristics and time dependent electrical resistivity effects are only observed in PP filled with VGCF. Several mechanisms must be called upon to explain the observed electrical behaviour of the PP/VGCF composite. The thermal conductivity of the composites is in agreement with the effective medium theories.

  17. Estimation of Water Vapour Attenuation And Rain Attenuation

    Directory of Open Access Journals (Sweden)

    K.Kalyana Srinivas

    2015-04-01

    Full Text Available Attenuation due to and water vapour and rain can severely degrade the radio wave propagation at centimeter or millimeter wavelengths. It restricts the path length of radio communication systems and limits the use of higher frequencies for line-of-sight microwave links and satellite communications. The attenuation will pose a greater problem to communication as the frequency of occurrence of heavy rain increases.In a tropical region, like Malaysia, where excessive rainfall is a common phenomenon throughout the year, the knowledge of the rain attenuation at the frequency of operation is extremely required for the design of a reliable terrestrial and earth space communication link at a particular location.

  18. Troposphere-stratosphere exchange - constraints from water vapour

    Science.gov (United States)

    Liu, Y.; Du, J.; Fueglistaler, S.; Haynes, P. H.

    2008-12-01

    Transport into the stratospheric 'overworld' is thought to occur predominantly across the tropical tropopause, whereas transport into the lowermost stratosphere may also occur through quasi-horizontal transport on isentropic levels between 300 and 380K potential temperature. The distribution of stratospheric water vapour is sensitively dependent upon the detailed temperature history of air parcel trajectories, and combined with a Lagrangian study can be used as a tracer for quantifying the relative importance of cross-isentropic mass flux and quasi-isentropic mass flux into the stratosphere. Here we combine measurements from the Microwave Limb Sounder on board of AURA satellite, with trajectory calculations to diagnose the pathways of troposphere-stratosphere exchange. Trajectories are calculated using winds and diabatic heating rates from the new interim reanalysis currently carried out at the European Centre for Medium-range Weather Forecast.

  19. Atmospheric pressure vapour phase decomposition: a proof of principle.

    Science.gov (United States)

    Cinosi, Amedeo; Andriollo, Nunzio; Tibaldi, Francesca; Monticelli, Damiano

    2012-11-15

    In the present work we demonstrated that the digestion of difficult matrices (high boiling petrochemical fractions and distillation bottoms) can be achieved by oxidation with nitric acid vapours at atmospheric pressure employing simple laboratory glassware. The application of this procedure as a digestion method prior to Total Reflection X-Ray Fluorescence (TXRF) is presented, although the employment of other detection techniques may be foreseen. The method ensured a fast, less than half an hour, treatment time and detection limits in the range 20-100 μg/kg for As, Bi, Co, Cr, Cu, Fe, Mn, Ni, Pb, Sr, Zn, whereas higher values were obtained for Ba, Ca, K, P, Rh, Ti and V (0.3-3 mg/kg). The potentialities and limitations of this procedure were discussed: the application to a broad range of matrices may be foreseen. Copyright © 2012 Elsevier B.V. All rights reserved.

  20. Thermoluminescence characterisation of chemical vapour deposited diamond films

    CERN Document Server

    Mazzocchi, S; Bucciolini, M; Cuttone, G; Pini, S; Sabini, M G; Sciortino, S

    2002-01-01

    The thermoluminescence (TL) characteristics of a set of six chemical vapour deposited diamond films have been studied with regard to their use as off-line dosimeters in radiotherapy. The structural characterisation has been performed by means of Raman spectroscopy. Their TL responses have been tested with radiotherapy beams ( sup 6 sup 0 Co photons, photons and electrons from a linear accelerator (Linac), 26 MeV protons from a TANDEM accelerator) in the dose range 0.1-7 Gy. The dosimetric characterisation has yielded a very good reproducibility, a very low dependence of the TL response on the type of particle and independence of the radiation energy. The TL signal is not influenced by the dose rate and exhibits a very low thermal fading. Moreover, the sensitivity of the diamond samples compares favourably with that of standard TLD100 dosimeters.

  1. Cavity-enhanced frequency up-conversion in rubidium vapour

    CERN Document Server

    Offer, Rachel F; Riis, Erling; Franke-Arnold, Sonja; Arnold, Aidan S

    2016-01-01

    We report the first use of a ring cavity to both enhance the output power and dramatically narrow the linewidth ($<1\\,$MHz) of blue light generated by four wave mixing in a rubidium vapour cell. We find that the high output power available in our cavity-free system leads to power broadening of the generated blue light linewidth. Our ring cavity removes this limitation, allowing high output power and narrow linewidth to be achieved concurrently. As the cavity blue light is widely tunable over the $^{85}$Rb 5S$_{1/2} \\,\\,F=3$ $\\rightarrow$ 6P$_{3/2}$ transition, this narrow linewidth light would be suitable for second-stage laser cooling, which could be valuable for efficient $^{85}$Rb BEC production.

  2. Dissecting the effect of anions on Hg2+ detection using a FRET based DNA probe.

    Science.gov (United States)

    Kiy, Mehmet Murat; Zaki, Ahmed; Menhaj, Arsalsan Beg; Samadi, Azadeh; Liu, Juewen

    2012-08-07

    Many biosensors have been developed to detect Hg(2+) using thymine-rich DNA. While sensor response to various cations is often studied to demonstrate selectivity, the effect of anions has been largely overlooked. Anions may compete with DNA for metal binding and thus produce a false negative result. Anions cannot be added alone; the cation part of a salt may cause DNA compaction and other effects, obscuring the role of anions. We find that the sensitivity of a FRET-based Hg(2+) probe is independent of Na(+) concentration. Therefore, by using various sodium salts, any change in sensitivity can be attributed solely to the effect of anions. Halide salts, sulfides, and amines are strong inhibitors; anions containing oxo or hydroxyl groups (e.g. nitrate, sulfate, phosphate, carbonate, acetate, and citrate) do not interfere with Hg(2+) detection even at 100 mM concentration. Mercury hydrolysis and its diffusion into polypropylene containers can also strongly affect the detection results. We conclude that thymine-rich DNA should be useful for Hg(2+) detection in many environmental water samples.

  3. Adsorption behaviors of Hg(II) on chitosan functionalized by amino-terminated hyperbranched polyamidoamine polymers.

    Science.gov (United States)

    Ma, Fang; Qu, Rongjun; Sun, Changmei; Wang, Chunhua; Ji, Chunnuan; Zhang, Ying; Yin, Ping

    2009-12-30

    The adsorption behaviors of Hg(II) on adsorbents, chitosan functionalized by generation 1.0-3.0 of amino-terminated hyperbranched polyamidoamine polymers (denoted as CTS-1.0, CTS-2.0 and CTS-3.0, respectively), were studied. The optimum pH corresponding to the maximum adsorption capacities was found to be 5.0 for the three adsorbents. The experimental equilibrium data of Hg(II) on the three adsorbents were fitted to the Freundlich and the Langmuir models, and it is found that the Langmuir isotherm was the best fitting model to describe the equilibrium adsorption. The kinetics data indicated that the adsorption process of Hg(II) ions on CTS-1.0, CTS-2.0 and CTS-3.0 were governed by the film diffusion and followed pseudo-second-order rate model. Thermodynamic analysis and FTIR analysis revealed that the adsorption behaviors of Hg(II) ions on the three adsorbents could be considered as spontaneous, endothermic and chemical sorption process, resulting in their higher adsorption capacities at higher temperature.

  4. Removal of Cd (II and Hg(II by chelating resin Chelex-100

    Directory of Open Access Journals (Sweden)

    Afaf Amara-Rekkab

    2015-03-01

    Full Text Available A sensitive, simple method for the determination of amounts of mixture of Hg2+and Cd2+ by spectrophotometry was described based on the formation of the Hg2+- Cd2+- PAN complex in water media. Optimal conditions such as reagent amounts, and pH for the Hg2+- Cd2+ determination were reported. It was found that the 2:1 PAN- Hg2+- Cd2+ complex dominate at pH 13.0. In another hand, the sorption of mixture mercury (II and cadmium (II from aqueous medium on a chelating resin Chelex 100 was studied in batch mode. Since the extraction kinetic was obtained, with a mixture of 0.1 g of resin and 5 mL of mixture at 1 mmol/L of initial concentration, extraction equilibrium was reached within 20 min of mixing. The influence of some parameters such as initial mixture ions concentrations, initial pH of aqueous solution, ion strength and the amounts of resin have been studied at fixed temperature (20±1°C. The optimum pH value level for quantitative sorption was up to 2.6. The best performance obtained was 97.1% of extraction yield equivalent to 15.65 mg/g of resin. The pseudo-first- order, pseudo-second-order models and the intra-particle diffusion model were used to describe the kinetic data and rate constants were evaluated.

  5. Directional Solidification and Characterization of Hg(0.89) Mn(0.11)Te

    Science.gov (United States)

    Price, M. W.; Scripa, R. N.; Lehoczky. S. L.; Szofran, F. R.; Su, C.-H.

    1998-01-01

    Two boules of Hg(0.89)Mn(0.11)Te(MMT) were solidified using the vertical Bridgman-Stockbarger method. Translation rates of 0.09 and 0. 18 microns/s were used. The influence of growth rate on axial compositional homogeneity in the MMT boules was evaluated experimentally by conducting precision density measurements on radial slices taken from each boule. In addition, Plane Front Solidification theory and segregation coefficient (k) data for the Hg(1-x)Mn(x)Te system were used to fit theoretical composition profiles to the measured MMT axial composition profiles. The strong correlation between the measured and calculated MMT axial composition profiles indicates diffusion dominated axial solute redistribution in the boules under the applied growth conditions. The analysis of the MMT axial composition profiles by Plane Front Solidification theory allowed the calculation of the effective diffusion coefficient (D(eff) = 3.5 x l0(exp -5) sq cm/s). The k-values for the Hg(1-x)Mn(x)Te system and the D(sub eff) - value were then used to verify that both boules were solidified under conditions which did not exceed the Constitutional Supercooling Criteria under ideal conditions. Finally, a preliminary examination of the radial compositional variation in each MMT was made using Fourier Transform Infra-Red Spectroscopy (FTIR). The radial homogeneity in the MMT boules was found to be comparable for both translation rates.

  6. Heat transfer in vapour-liquid flow of carbon dioxide

    Energy Technology Data Exchange (ETDEWEB)

    Yagov, V.V. [Moscow Power Engineering Institute (Technical University), Moscow (Russian Federation)], e-mail: YagovVV@mpei.ru

    2009-07-01

    During the last decade a number of studies of boiling heat transfer in carbon dioxide notably increase. As a field of CO{sub 2} practical using corresponds to high reduced pressures, and a majority of available experimental data on CO{sub 2} flow boiling even in submillimetric channels relate to turbulent liquid flow regimes, a possibility arises to develop sufficiently general method for HTC predicting. Under the above conditions nucleate boiling occurs up to rather high flow quality, even in annular flow regime due to extremely small size of an equilibrium vapour bubble. This conclusion is in agreement with the available experimental data. The predicting equation for nucleate boiling heat transfer developed by the present author in 1988 is valid for any nonmetallic liquid. A contribution of forced convection in heat transfer is calculated according to the Petukhov et al. equation with correction factor, which accounted for an effect of velocity increase due to evaporation. This effect can be essential at relatively small heat fluxes and rather high mass flow rates. The Reynolds analogy and homogeneous model are used in order to account for the convective heat transfer augmentation in two-phase flow. Due to low ratio of liquid and vapour densities at high reduced pressures the homogeneous approximation of two-phase flow seems to be warranted. A total heat transfer coefficient is calculated as an interpolated value of boiling and convective HTCs. The experimental data on CO{sub 2} flow boiling related to regimes before heated wall dryout incipience are in rather good agreement with the calculations. (author)

  7. Heat transfer in vapour-liquid flow of carbon dioxide

    Energy Technology Data Exchange (ETDEWEB)

    Yagov, V.V. [Moscow Power Engineering Institute (Technical University), Moscow (Russian Federation)], e-mail: YagovVV@mpei.ru

    2009-07-01

    During the last decade a number of studies of boiling heat transfer in carbon dioxide notably increase. As a field of CO{sub 2} practical using corresponds to high reduced pressures, and a majority of available experimental data on CO{sub 2} flow boiling even in submillimetric channels relate to turbulent liquid flow regimes, a possibility arises to develop sufficiently general method for HTC predicting. Under the above conditions nucleate boiling occurs up to rather high flow quality, even in annular flow regime due to extremely small size of an equilibrium vapour bubble. This conclusion is in agreement with the available experimental data. The predicting equation for nucleate boiling heat transfer developed by the present author in 1988 is valid for any nonmetallic liquid. A contribution of forced convection in heat transfer is calculated according to the Petukhov et al. equation with correction factor, which accounted for an effect of velocity increase due to evaporation. This effect can be essential at relatively small heat fluxes and rather high mass flow rates. The Reynolds analogy and homogeneous model are used in order to account for the convective heat transfer augmentation in two-phase flow. Due to low ratio of liquid and vapour densities at high reduced pressures the homogeneous approximation of two-phase flow seems to be warranted. A total heat transfer coefficient is calculated as an interpolated value of boiling and convective HTCs. The experimental data on CO{sub 2} flow boiling related to regimes before heated wall dryout incipience are in rather good agreement with the calculations. (author)

  8. ROIC for HgCdTe e-APD FPA

    Science.gov (United States)

    Chen, Guoqiang; Zhang, Junling; Wang, Pan; Zhou, Jie; Gao, Lei; Ding, Ruijun

    2013-08-01

    Ultra-low light imaging and passive/active dual mode imaging require very low noise optical receivers to achieve detection of fast and weak optical signal. HgCdTe electrons initiated avalanche photodiodes (e-APDs) in linear multiplication mode is the detector of choice thanks to its high quantum efficiency, high gain at low bias, high bandwidth and low noise factor. In my work, a passive/active dual mode readout integrated circuit (ROIC) of e-APD focal plane array (FPA) is designed. Unit cell circuit architecture of ROIC includes a capacitance feedback transimpedance amplifier (CTIA) as preamplifier of ROIC, a high voltage protection module, a comparator, a Sample-Hold circuit module, and output driver stage. There is a protection module in every unit cell circuit which can avoid ROIC to be damaged from avalanche breakdown of some diodes of detector. Conventional 5V CMOS process is applied to implement the high voltage protection with the small area rather than Laterally Diffused Metal Oxide Semiconductor (LDMOS) in high voltage BCD process in the limited 100um×100um pitch area. In CTIA module, three integration capacitances are included in the CTIA module, two of them are switchable to provide different well capacity and noise. Constraints such as pixel area, stability and power lead us design toward a simple one-stage cascade operational transconductance amplifier (OTA) as pre-amplifier. High voltage protection module can protect ROIC to be damaged because of breakdown of some avalanche diodes.

  9. Mass Independent Fractionation of Hg Isotopes Preserved in the Precambrian

    Science.gov (United States)

    Thibodeau, A. M.; Bergquist, B. A.; Kah, L. C.; Ono, S.; Ghosh, S.; Hazen, R. M.

    2013-12-01

    Mercury (Hg) is a photochemically active, redox-sensitive, chalcophilic metal with complex biogeochemistry that displays a wide range of mass-dependent (MDF) and mass-independent (MIF) stable isotopic fractionation. In the past decade, Hg isotopes have emerged as important tracers of both the sources and cycling of Hg in the modern environment. However, their utility as environmental proxies in ancient rocks remains largely unexplored. The potential of Hg isotopes to inform Precambrian environments derives from the observation that Hg isotopes with odd atomic mass numbers (199Hg and 201Hg) undergo large MIF by the magnetic isotope effect (MIE) and smaller MIF through the nuclear volume effect (NVE). Small MIF produced via NVE has been observed for numerous transformations and is characterized by MIF ratios (Δ199Hg/Δ201Hg) of about 1.6. Large Hg-MIF driven by MIE has been observed during photochemical transformations and is characterized by Δ199Hg/Δ201Hg ratios between 1 and 1.3. This MIF signal is sensitive to a range of environmental conditions, including the amount and type of solar radiation, the presence and type of complexing organic ligands, and the Hg/dissolved organic carbon (DOC) ratio. Thus, it is hoped that Hg-MIF signals may indirectly record changes in atmospheric composition or seawater chemistry if preserved in marine sedimentary records. Previous work has clearly demonstrated that Hg-MIF signals are preserved in Archean and Paleoproterozoic marine shales and massive sulfide deposits. Here, we present evidence that such signals are also preserved in marine shales of mid-Proterozoic age, including the ~1.3 Ga Sulky formation (Dismal Lakes Group, NW Arctic), the ~1.45 Ga Greyson Shale (Belt Basin, Montana), and the ~1.5 Ga Katalsy formation (Kypry Group, Eastern European Platform). We observe that the Greyson shale and shales within the Sulky formation yield negative Hg-MIF with Δ199Hg/Δ201Hg ratios close to 1 and that Kaltasy group sediments

  10. Superdeformation studies in {sup 191}Hg

    Energy Technology Data Exchange (ETDEWEB)

    Carpenter, M.P.; Janssens, R.V.F.; Crowell, B. [and others

    1995-08-01

    Superdeformation in the A {approximately} 190 region was first observed in {sup 191}Hg from an experiment performed at ATLAS using the Argonne Notre Dame {gamma}-ray facility. We recently revisited the study of superdeformation in this nucleus using Gammasphere and the {sup 160}Gd({sup 36}S,5n) and {sup 174}Yb({sup 22}Ne,5n) reactions at 172 and 120 MeV in order to populate and measure states in the second well. The goal of the experiment was to identify new bands in the data, and thus allow us to gain understanding on the relative placement of single particle orbitals near the N = 112 SD shell gap. From an analysis of the data, the three previously identified SD bands were extended, and their feeding into the yrast states delineated. Two new SD bands were observed and preliminary evidence for a third new band was obtained as well.

  11. Modelling water vapour permeability through atomic layer deposition coated photovoltaic barrier defects

    Energy Technology Data Exchange (ETDEWEB)

    Elrawemi, Mohamed, E-mail: Mohamed.elrawemi@hud.ac.uk [EPSRC Centre for Innovative Manufacturing in Advanced Metrology, School of Computing and Engineering, University of Huddersfield, Huddersfield (United Kingdom); Blunt, Liam; Fleming, Leigh [EPSRC Centre for Innovative Manufacturing in Advanced Metrology, School of Computing and Engineering, University of Huddersfield, Huddersfield (United Kingdom); Bird, David, E-mail: David.Bird@uk-cpi.com [Centre for Process Innovation Limited, Sedgefield, County Durham (United Kingdom); Robbins, David [Centre for Process Innovation Limited, Sedgefield, County Durham (United Kingdom); Sweeney, Francis [EPSRC Centre for Innovative Manufacturing in Advanced Metrology, School of Computing and Engineering, University of Huddersfield, Huddersfield (United Kingdom)

    2014-11-03

    Transparent barrier films such as Al{sub 2}O{sub 3} used for prevention of oxygen and/or water vapour permeation are the subject of increasing research interest when used for the encapsulation of flexible photovoltaic modules. However, the existence of micro-scale defects in the barrier surface topography has been shown to have the potential to facilitate water vapour ingress, thereby reducing cell efficiency and causing internal electrical shorts. Previous work has shown that small defects (≤ 3 μm lateral dimension) were less significant in determining water vapour ingress. In contrast, larger defects (≥ 3 μm lateral dimension) seem to be more detrimental to the barrier functionality. Experimental results based on surface topography segmentation analysis and a model presented in this paper will be used to test the hypothesis that the major contributing defects to water vapour transmission rate are small numbers of large defects. The model highlighted in this study has the potential to be used for gaining a better understanding of photovoltaic module efficiency and performance. - Highlights: • A model of water vapour permeation through barrier defects is presented. • The effect of the defects on the water vapour permeability is investigated. • Defect density correlates with water vapour permeability. • Large defects may dominate the permeation properties of the barrier film.

  12. Relationship Between Soil Properties and Different Fractions of Soil Hg

    Institute of Scientific and Technical Information of China (English)

    WUHONGTAO; YUGUIFEN; 等

    2001-01-01

    Correlation and path analysis methods were used to study the relationship between soil properties and the distribution of different soil Hg fractions with nine representative soils from Chongqing,China,Results showed that clay(<2m) could increase water-soluble Hg(r=0.700*).Soil organic matter (OM) could enhance the increase of elemental Hg(r=0.674*),The higher the base saturation percentage (BSP) ,the more the residual Hg(R=0.684*) .Organic Hg,the sum of said-soluble organic He and alkali-soluble Hg,was positively affected by silt(2-20μm)but negatively affected by pH,with the direct path coefficients amounting to 1.0487 and 0.5121,respectively .The positive effect of OM and negative effect of BSP on organic Hg were the most significant ,with the direct path coefficients being 0.7614 and -0.8527,respectively. The indirect effect of clay(<2μm) iva BSP (path coefficient=0.4186) was the highest,showing that the real influencing factor in the effect of clay(<2μm) via BSP (path coefficient=0.4186) was the highest,showing that the real influencing factor in the effect of clay(<2μm) on acid-soluble organic Hw was BSP.since the available Hg fraction,water-soluble Hg,was positively affected by soil clay content,and the quite immobile and not bioavailable residual Hg by soil BSP,suitable reduction of clay content and increase of BSP would be of much help to reduce the Hg availability and Hg activity in Hg-contaminated soils.

  13. Anisotropic silver nanoparticles deposited on zeolite a for selective Hg2+ colorimetric sensing and antibacterial studies

    Directory of Open Access Journals (Sweden)

    Khorshidi Alireza

    2015-01-01

    Full Text Available Silver nanoparticles deposited on the surface of zeolite A were prepared via post ion-exchange reduction, and reduction-deposition methods. Formation of the silver nanoparticles on the surface of zeolite A was verified by surface plasmon spectra using diffuse reflectance spectroscopy and ultraviolet-visible spectroscopy. Morphology of the prepared samples was characterized by X-ray diffraction and scanning electron microscopy. Furthermore, silver nanoparticles deposited on the zeolite A, after fixation of Rhodamine B dye molecules over themselves, were successful in detecting Hg2+ ions selectively. After treatment with the so-obtained sensor, color change from colorless to pink was visible to the naked eye for the Hg2+ solution concentrations down to 1.0×10-8 mol.L-1. Antibacterial tests demonstrated the multifunctional application of the silver nanoparticles deposited on zeolite A.

  14. Quantitative imaging of D-2-hydroxyglutarate (D2HG in selected histological tissue areas by a novel bioluminescence technique

    Directory of Open Access Journals (Sweden)

    Nadine Fabienne Voelxen

    2016-03-01

    Full Text Available AbstractPatients with malignant gliomas have a poor prognosis with average survival of less than one year. Whereas in other tumor entities the characteristics of tumor metabolism are successfully used for therapeutic approaches, such developments are very rare in brain tumors, notably in gliomas. One metabolic feature characteristic of gliomas, in particular diffuse astrocytomas and oligodendroglial tumors, is the variable content of D-2-hydroxyglutarate (D2HG, a metabolite, which was discovered first in this tumor entity. D2HG is generated in large amounts due to various gain-of–function mutations in the isocitrate dehydrogenases IDH-1 and IDH-2. Meanwhile, D2HG has been detected in several other tumor entities including intrahepatic bile-duct cancer, chondrosarcoma, acute myeloid leukemia, and angioimmunoblastic T-cell lymphoma. D2HG is barely detectable in healthy tissue (< 0.1 mM, but its concentration increases up to 35 mM in malignant tumor tissues. Consequently, the oncometabolite D2HG has gained increasing interest in the field of tumor metabolism. To facilitate its quantitative measurement without loss of spatial resolution at a microscopical level, we have developed a novel bioluminescence assay for determining D2HG in sections of snap-frozen tissue. The assay was verified independently by photometric tests and liquid chromatography / mass spectrometry (LC/MS. The novel technique allows the microscopically resolved determination of D2HG in a concentration range of 0 – 10 µmol/g tissue (wet weight. In combination with the already established bioluminescence imaging techniques for ATP, glucose, pyruvate, and lactate, the novel D2HG assay enables a comparative characterization of the metabolic profile of individual tumors in a further dimension.

  15. Ozone and water vapour in the austral polar stratospheric vortex and sub-vortex

    OpenAIRE

    Peet, E.; V. Rudakov; V. Yushkov; G. Redaelli; A. R. MacKenzie

    2004-01-01

    In-situ measurements of ozone and water vapour, in the Antarctic lower stratosphere, were made as part of the APE-GAIA mission in September and October 1999. The measurements show a distinct difference above and below the 415K isentrope. Above 415K, the chemically perturbed region of low ozone and water vapour is clearly evident. Below 415K, but still above the tropopause, no sharp meridional gradients in ozone and water vapour were observed. The observations are consistent with analyses of p...

  16. Development of insulated gate bipolar transistor-based power supply for elemental copper vapour laser

    Indian Academy of Sciences (India)

    R K Mishra; S V Nakhe; G N Tiwari; J K Mittal

    2010-11-01

    The elemental copper vapour laser is a widely used laser from a family of metal vapour lasers for applications such as dye laser pumping, micromachining etc. In this paper, we report the development and performance of IGBT-based pulsed power supply that replaced conventional thyratron-based power supply for 4.7 cm diameter, 150 cm long copper vapour laser. The laser tube delivered an average power of 51 W, which with conventional power supply was giving 40 W. The IGBT-based power supply offers considerable reduction in the running cost of the laser. It is more user-friendly when compared with the conventional power supply.

  17. Solid state and sub-cooled liquid vapour pressures of cyclic aliphatic dicarboxylic acids

    Directory of Open Access Journals (Sweden)

    A. M. Booth

    2010-10-01

    Full Text Available Knudsen Effusion Mass Spectrometry (KEMS has been used to measure for the first time the solid state vapour pressures of a series of aliphatic cyclic dicarboxylic acids with increasing ring size. Additionally the atmospherically important compounds; cis-pinonic acid and levoglucosan were also measured. Differential Scanning Calorimetry (DSC was used to measure melting points, enthalpies and entropies of fusion, which were used to determine sub-cooled liquid vapour pressures for the compounds. The sub-cooled liquid vapour pressure of straight chain, branched and cyclic dicarboxylic acids was compared to a selection of estimation methods.

  18. Utility of DMSP-SSM/I for integrated water vapour over the Indian seas

    Indian Academy of Sciences (India)

    P N Mahajan

    2001-09-01

    Recent algorithms for Special Sensor Microwave/Imager (DMSP-SSM/I) satellite data are used for estimating integrated water vapour over the Indian seas. Integrated water vapour obtained from these algorithms is compared with that derived from radiosonde observations at Minicoy and Port Blair islands. Algorithm-3 of Schlussel and Emery (1990) performed best. On the basis of this algorithm, distribution of integrated water vapour is determined during the monsoon depression (22nd{27th July, 1992) that formed over the Bay of Bengal.

  19. Static and dynamic properties of curved vapour-liquid interfaces by massively parallel molecular dynamics simulation

    CERN Document Server

    Horsch, Martin T; Vrabec, Jadran; Glass, Colin W; Niethammer, Christoph; Bernreuther, Martin F; Müller, Erich A; Jackson, George

    2011-01-01

    Curved fluid interfaces are investigated on the nanometre length scale by molecular dynamics simulation. Thereby, droplets surrounded by a metastable vapour phase are stabilized in the canonical ensemble. Analogous simulations are conducted for cylindrical menisci separating vapour and liquid phases under confinement in planar nanopores. Regarding the emergence of nanodroplets during nucleation, a non-equilibrium phenomenon, both the non-steady dynamics of condensation processes and stationary quantities related to supersaturated vapours are considered. Results for the truncated and shifted Lennard-Jones fluid and for mixtures of quadrupolar fluids confirm the applicability of the capillarity approximation and the classical nucleation theory.

  20. Deuterium excess in the atmospheric water vapour of a Mediterranean coastal wetland: regional vs. local signatures

    Science.gov (United States)

    Delattre, H.; Vallet-Coulomb, C.; Sonzogni, C.

    2015-09-01

    Stable isotopes of water vapour represent a powerful tool for tracing atmospheric vapour origin and mixing processes. Laser spectrometry recently allowed high time-resolution measurements, but despite an increasing number of experimental studies, there is still a need for a better understanding of the isotopic signal variability at different time scales. We present results of in situ measurements of δ18O and δD during 36 consecutive days in summer 2011 in atmospheric vapour of a Mediterranean coastal wetland exposed to high evaporation (Camargue, Rhône River delta, France). The mean composition of atmospheric vapour (δv) is δ18O = -14.66 ‰ and δD = - 95.4 ‰, with data plotting clearly above the local meteoric water line on a δ18O-δD plot, and an average deuterium excess (d) of 21.9 ‰. Important diurnal d variations are observed, and an hourly time scale analysis is necessary to interpret the main processes involved in its variability. After having classified the data according to air mass back trajectories, we analyse the average daily cycles relating to the two main meteorological situations, i.e. air masses originating from North Atlantic Ocean and Mediterranean Sea. In both situations, we show that diurnal fluctuations are driven by (1) the influence of local evaporation, culminating during daytime, and leading to an increase in absolute water vapour concentration associated to a δv enrichment and d increase; (2) vertical air mass redistribution when the Planetary Boundary Layer collapses in the evening, leading to a d decrease, and (3) dew formation during the night, producing a δv depletion with d remaining stable. Using a two-component mixing model, we calculate the average composition of the locally evaporated vapour (δE). We find higher d(E) under North Atlantic air mass conditions, which is consistent with lower humidity conditions. We also suggest that δv measured when the PBL collapses is the most representative of a regional signal

  1. Low pressure water vapour discharge as a light source: I. Spectroscopic characteristics and efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Artamonova, E; Artamonova, T; Beliaeva, A; Gorbov, D; Khodorkovskii, M; Melnikov, A; Milenin, V; Murashov, S; Rakcheeva, L; Timofeev, N [Saint-Petersburg State University, Ulyanovskaya 3, 198504 (Russian Federation); Michael, D [General Electric Global Research Center, One Research Circle (Bldg K1 Rm 4B31), Niskayuna, NY, 12309 (United States)], E-mail: timofeev@pobox.spbu.ru, E-mail: michael@crd.ge.com

    2008-08-07

    Spectral and electrical characteristics of a low pressure dc discharge formed from a mixture of one of the rare gases Ne, Ar or Kr plus water vapour are studied. Water vapour is only a minor additive to the rare gas. It has been shown that enhanced emission of the OH 306.4 nm band is registered from the discharge of Ar mixed with water vapour. Plasmas from the other investigated rare gases yielded considerably less OH 306.4 nm emission. Data about consumed electric power, spectra and relative efficiencies are presente000.

  2. Effects of vapour bubbles on acoustic and temperature distributions of therapeutic ultrasound

    Institute of Scientific and Technical Information of China (English)

    Fan Ting-Bo; Zhang Dong; Zhang Zhe; Ma Yong; Gong Xiu-Fen

    2008-01-01

    This paper describes the evolution of vapour bubbles and its effect on nonlinear ultrnsound propagation and temperature rise through tissues for therapeutic ultrasound.An acoustic-thermo coupling algorithm incorporating nonlinearity,diffraction,and temperature-dependent tissue properties,is employed to describe nonlinear ultrasound propagation and thermal effect.Results demonstrate that an obvious migration of peak pressure toward transducer surface is observed while the position of peak temperature changes little in liver tissue before the generation of vapour bubbles,and that the boiling region enlarges towards the surface of transducer in axial direction but increases slowly in radial direction after the generation of vapour bubbles.

  3. Oxidative stress in MeHg-induced neurotoxicity

    Energy Technology Data Exchange (ETDEWEB)

    Farina, Marcelo, E-mail: farina@ccb.ufsc.br [Departamento de Bioquimica, Centro de Ciencias Biologicas, Universidade Federal de Santa Catarina, Florianopolis, SC (Brazil); Aschner, Michael [Department of Pediatrics, Vanderbilt University Medical Center, Nashville, TN (United States); Department of Pharmacology, Vanderbilt University Medical Center, Nashville, TN (United States); Rocha, Joao B.T., E-mail: jbtrocha@yahoo.com.br [Departamento de Quimica, Centro de Ciencias Naturais e Exatas, Universidade Federal de Santa Maria, Santa Maria, RS (Brazil)

    2011-11-15

    Methylmercury (MeHg) is an environmental toxicant that leads to long-lasting neurological and developmental deficits in animals and humans. Although the molecular mechanisms mediating MeHg-induced neurotoxicity are not completely understood, several lines of evidence indicate that oxidative stress represents a critical event related to the neurotoxic effects elicited by this toxicant. The objective of this review is to summarize and discuss data from experimental and epidemiological studies that have been important in clarifying the molecular events which mediate MeHg-induced oxidative damage and, consequently, toxicity. Although unanswered questions remain, the electrophilic properties of MeHg and its ability to oxidize thiols have been reported to play decisive roles to the oxidative consequences observed after MeHg exposure. However, a close examination of the relationship between low levels of MeHg necessary to induce oxidative stress and the high amounts of sulfhydryl-containing antioxidants in mammalian cells (e.g., glutathione) have led to the hypothesis that nucleophilic groups with extremely high affinities for MeHg (e.g., selenols) might represent primary targets in MeHg-induced oxidative stress. Indeed, the inhibition of antioxidant selenoproteins during MeHg poisoning in experimental animals has corroborated this hypothesis. The levels of different reactive species (superoxide anion, hydrogen peroxide and nitric oxide) have been reported to be increased in MeHg-exposed systems, and the mechanisms concerning these increments seem to involve a complex sequence of cascading molecular events, such as mitochondrial dysfunction, excitotoxicity, intracellular calcium dyshomeostasis and decreased antioxidant capacity. This review also discusses potential therapeutic strategies to counteract MeHg-induced toxicity and oxidative stress, emphasizing the use of organic selenocompounds, which generally present higher affinity for MeHg when compared to the classically

  4. Modeling interactions of Hg(II) and bauxitic soils.

    Science.gov (United States)

    Weerasooriya, Rohan; Tobschall, Heinz J; Bandara, Atula

    2007-11-01

    The adsorptive interactions of Hg(II) with gibbsite-rich soils (hereafter SOIL-g) were modeled by 1-pK surface complexation theory using charge distribution multi-site ion competition model (CD MUSIC) incorporating basic Stern layer model (BSM) to account for electrostatic effects. The model calibrations were performed for the experimental data of synthetic gibbsite-Hg(II) adsorption. When [NaNO(3)] > or = 0.01M, the Hg(II) adsorption density values, of gibbsite, Gamma(Hg(II)), showed a negligible variation with ionic strength. However, Gamma(Hg(II)) values show a marked variation with the [Cl(-)]. When [Cl(-)] > or = 0.01M, the Gamma(Hg(II)) values showed a significant reduction with the pH. The Hg(II) adsorption behavior in NaNO(3) was modeled assuming homogeneous solid surface. The introduction of high affinity sites, i.e., >Al(s)OH at a low concentration (typically about 0.045 sites nm(-2)) is required to model Hg(II) adsorption in NaCl. According to IR spectroscopic data, the bauxitic soil (SOIL-g) is characterized by gibbsite and bayerite. These mineral phases were not treated discretely in modeling of Hg(II) and soil interactions. The CD MUSIC/BSM model combination can be used to model Hg(II) adsorption on bauxitic soil. The role of organic matter seems to play a role on Hg(II) binding when pH>8. The Hg(II) adsorption in the presence of excess Cl(-) ions required the selection of high affinity sites in modeling.

  5. Lithography process for patterning HgI2 photonic devices

    Science.gov (United States)

    Mescher, Mark J.; James, Ralph B.; Hermon, Haim

    2004-11-23

    A photolithographic process forms patterns on HgI.sub.2 surfaces and defines metal sublimation masks and electrodes to substantially improve device performance by increasing the realizable design space. Techniques for smoothing HgI.sub.2 surfaces and for producing trenches in HgI.sub.2 are provided. A sublimation process is described which produces etched-trench devices with enhanced electron-transport-only behavior.

  6. Diffusion and pulsations in slowly rotating B stars

    CERN Document Server

    Turcotte, S

    2005-01-01

    Diffusion in cool B stars of the main sequence has been shown to strongly affect opacities and convection in cool B stars of the main sequence. We show here that diffusion in B stars maintains or enhances the excitation of pulsations in these stars. This result conflicts with observations as cool B stars that show evidence of diffusion, the HgMn stars, are stable to the current detection level. We discuss possible implications of this discrepancy for the models.

  7. Experiments with a New 201Hg+ Ion Clock

    Science.gov (United States)

    Burt, E. A.; Taghavi-Larigani, S.; Lea, S. N.; Prestage, J. D.; Tjoelker, R. L.

    2009-04-01

    In this paper we describe a new clock based on 201Hg+. All previous mercury ion clocks have been based on 199Hg+. We have recently completed construction of the 201Hg+ clock and will describe modifications to the design of our existing 199Hg+ clocks to accommodate the new isotope. We will also describe initial spectroscopic measurements of the hyperfine manifold, and possible future experiments. One experiment could place a limit on variations in the strong interaction fundamental constant ratio mq/ΛQCD.REFID="9789812838223_0043FN001">

  8. PENCEMARAN LOGAM BERAT MERKURI (Hg PADA AIRTANAH

    Directory of Open Access Journals (Sweden)

    Thomas Triadi Putranto

    2012-02-01

    Full Text Available The earth consists largely of water because the land area is smaller than the ocean. Human beings on this earthcan not escape the need for water. Water is the main requirement for the process of life on the earth.Relatively clean water that is coveted by men, whether for purposes of daily life, for industrial purposes, for thecleanliness of city sanitation, as well as for agricultural purposes and so forth. Heavy metal pollution is a veryserious issue to be handled, because of adverse environmental and ecosystem in general. Heavy metallic elementis the element which has a density of more than 5 gr/cm3. Hg has a density of 13.55 gr/cm3. Disaster is anoutbreak of Minamata mercury poisoning in people who eat fish contaminated by mercury in Minamata Japan,and this event is known as Minamata Disease. Efforts to tackle the heavy metal pollution can actually be doneusing a chemical process or by microorganism such as microbes and bacteria.

  9. Hg-coordination studies of oligopeptides containing cysteine, histidine and tyrosine by $^{199m}$Hg-TDPAC

    CERN Document Server

    Ctortecka, B; Mallion, S; Butz, T; Hoffmann, R

    1999-01-01

    In order to study the interaction of histidine- and tyrosine- containing peptide chains with Hg(II), the nuclear quadrupole interaction (NQI) of /sup 199m/Hg in the Hg complexes of the oligopeptides alanyl-alanyl-histidyl-alanyl-alanine-amid (AAHAA-NH /sub 2/) and alanyl-alanyl-tyrosyl-alanyl-alanine-amid (AAYAA-NH/sub 2/) was determined by time differential perturbed angular correlation and is compared with previous data on alanyl-alanyl-cysteyl-alanyl- alanyl (AACAA-OH). The /sup 199m/Hg-NQIs depend on the oligopeptide to Hg(II) stoichiometry and indicate that two-fold and four-fold coordinations occur for the bound Hg(II). (12 refs).

  10. The Impact of Thermal Conductivity and Diffusion Rates on Water Vapor Transport through Gas Diffusion Layers

    CERN Document Server

    Burlatsky, S F; Gummallaa, M; Condita, D; Liua, F

    2013-01-01

    Water management in a hydrogen polymer electrolyte membrane (PEM) fuel cell is critical for performance. The impact of thermal conductivity and water vapor diffusion coefficients in a gas diffusion layer (GDL) has been studied by a mathematical model. The fraction of product water that is removed in the vapour phase through the GDL as a function of GDL properties and operating conditions has been calculated and discussed. Furthermore, the current model enables identification of conditions when condensation occurs in each GDL component and calculation of temperature gradient across the interface between different layers, providing insight into the overall mechanism of water transport in a given cell design. Water transport mode and condensation conditions in the GDL components depend on the combination of water vapor diffusion coefficients and thermal conductivities of the GDL components. Different types of GDL and water removal scenarios have been identified and related to experimentally-determined GDL proper...

  11. Towards outperforming conventional sensor arrays with fabricated individual photonic vapour sensors inspired by Morpho butterflies

    Science.gov (United States)

    Potyrailo, Radislav A.; Bonam, Ravi K.; Hartley, John G.; Starkey, Timothy A.; Vukusic, Peter; Vasudev, Milana; Bunning, Timothy; Naik, Rajesh R.; Tang, Zhexiong; Palacios, Manuel A.; Larsen, Michael; Le Tarte, Laurie A.; Grande, James C.; Zhong, Sheng; Deng, Tao

    2015-09-01

    Combining vapour sensors into arrays is an accepted compromise to mitigate poor selectivity of conventional sensors. Here we show individual nanofabricated sensors that not only selectively detect separate vapours in pristine conditions but also quantify these vapours in mixtures, and when blended with a variable moisture background. Our sensor design is inspired by the iridescent nanostructure and gradient surface chemistry of Morpho butterflies and involves physical and chemical design criteria. The physical design involves optical interference and diffraction on the fabricated periodic nanostructures and uses optical loss in the nanostructure to enhance the spectral diversity of reflectance. The chemical design uses spatially controlled nanostructure functionalization. Thus, while quantitation of analytes in the presence of variable backgrounds is challenging for most sensor arrays, we achieve this goal using individual multivariable sensors. These colorimetric sensors can be tuned for numerous vapour sensing scenarios in confined areas or as individual nodes for distributed monitoring.

  12. Influence of metallic vapours on the properties of air thermal plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Cressault, Y; Hannachi, R; Teulet, Ph; Gleizes, A [LAPLACE - UMR CNRS 5213, Universite de Toulouse 3, 118 route de Narbonne, 31062 Toulouse Cedex 9 (France); Gonnet, J-P; Battandier, J-Y [Schneider Electric, Innovation Division, 38TEC/T3 Plant, 37 Quai Paul-Louis Merlin F38000 Grenoble (France)], E-mail: yann.cressault@laplace.univ-tlse.fr

    2008-08-01

    This paper deals with properties of air thermal plasmas containing vapours of iron, silver or copper. The plasma is supposed to be in local thermodynamic equilibrium, for temperatures ranging from 2000 to 30 000 K. First, the equilibrium composition and thermodynamic properties are presented. Then, the radiative properties are calculated using the method of the net emission coefficient. Finally, the viscosity, electrical and thermal conductivities are calculated using the method of Chapman-Enskog. For all mixtures, mole fractions have been used. The results are computed for various values of pressure, plasma size and proportions of vapours. The influence of metallic vapour is important on the electrical conductivity and on the radiation, even at low concentration. All the metallic vapours present a similar behaviour except iron, which has a stronger radiation emission than the other components.

  13. Sensing response of copper phthalocyanine salt dispersed glass with organic vapours

    Energy Technology Data Exchange (ETDEWEB)

    Ridhi, R.; Sachdeva, Sheenam; Saini, G. S. S.; Tripathi, S. K., E-mail: surya@pu.ac.in [Department of Physics, Center of Advanced Study in Physics, Panjab University, Chandigarh-160 014 (INDIA) Fax: +91-172-2783336; Tel.:+91-172-2544362 (India)

    2016-05-06

    Copper Phthalocyanine and other Metal Phthalocyanines are very flexible and tuned easily to modify their structural, spectroscopic, optical and electrical properties by either functionalizing them with various substituent groups or by replacing or adding a ligand to the central metal atom in the phthalocyanine ring and accordingly can be made sensitive and selective to various organic species or gaseous vapours. In the present work, we have dispersed Copper Phthalocyanine Salt (CuPcS) in sol-gel glass form using chemical route sol-gel method and studied its sensing mechanism with organic vapours like methanol and benzene and found that current increases onto their exposure with vapours. A variation in the activation energies was also observed with exposure of vapours.

  14. Effects of Aqueous Vapour Consistence in Nitriding Furnace on the Quality of the Sintered Nitride

    Institute of Scientific and Technical Information of China (English)

    WANGZijiang

    1998-01-01

    If the aqueous vapour consistence is too high(>0.7%),it is very disadvantageous to the sintered products in the nitriding furnace,when silcon nitride bonded silicon carbide products are synthesized by nitridation of silicon.

  15. Organic Vapour Sensing Properties of Area-Ordered and Size-Controlled Silicon Nanopillar

    Directory of Open Access Journals (Sweden)

    Wei Li

    2016-11-01

    Full Text Available Here, a silicon nanopillar array (Si-NPA was fabricated. It was studied as a room-temperature organic vapour sensor, and the ethanol and acetone gas sensing properties were detected with I-V curves. I-V curves show that these Si-NPA gas sensors are sensitive to ethanol and acetone organic vapours. The turn-on threshold voltage is about 0.5 V and the operating voltage is 3 V. With 1% ethanol gas vapour, the response time is 5 s, and the recovery time is 15 s. Furthermore, an evaluation of the gas sensor stability for Si-NPA was performed. The gas stability results are acceptable for practical detections. These excellent sensing characteristics can mainly be attributed to the change of the overall dielectric constant of Si-NPA caused by the physisorption of gas molecules on the pillars, and the filling of the gas vapour in the voids.

  16. Organic Vapour Sensing Properties of Area-Ordered and Size-Controlled Silicon Nanopillar.

    Science.gov (United States)

    Li, Wei; Feng, Zhilin; Dai, Enwen; Xu, Jie; Bai, Gang

    2016-11-09

    Here, a silicon nanopillar array (Si-NPA) was fabricated. It was studied as a room-temperature organic vapour sensor, and the ethanol and acetone gas sensing properties were detected with I-V curves. I-V curves show that these Si-NPA gas sensors are sensitive to ethanol and acetone organic vapours. The turn-on threshold voltage is about 0.5 V and the operating voltage is 3 V. With 1% ethanol gas vapour, the response time is 5 s, and the recovery time is 15 s. Furthermore, an evaluation of the gas sensor stability for Si-NPA was performed. The gas stability results are acceptable for practical detections. These excellent sensing characteristics can mainly be attributed to the change of the overall dielectric constant of Si-NPA caused by the physisorption of gas molecules on the pillars, and the filling of the gas vapour in the voids.

  17. The thermotidal exciting function for water vapour absorption of solar radiation

    Directory of Open Access Journals (Sweden)

    M. BONAFEDE

    1976-06-01

    Full Text Available The thermotidal exciting function J is considered, for
    the absorption of solar radiation by water vapour, according to the model
    derived by Siebert. The Mugge-Moller formula for water vapour absorption
    is integrated numerically, using experimental data for the water vapour
    concentration in the troposphere and the stratosphere. It appears that
    Siebort's formula is a reasonable approximation at low tropospheric levels
    but it dramatically overestimates the water vapour thermotidal heating
    in the upper troposphere and in the stratosphere. It seems thus possible
    that, if the correct vertical profile is employed for J , the amplitudes and
    phases of the diurnal temperature oscillations and of the tidal wind speeds
    may suffer significant changes from those previously calculated and possibly explain the three hours delay of the observed phases from the computed values.

  18. Vapour sensitivity of an ALD hierarchical photonic structure inspired by Morpho.

    Science.gov (United States)

    Poncelet, Olivier; Tallier, Guillaume; Mouchet, Sébastien R; Crahay, André; Rasson, Jonathan; Kotipalli, Ratan; Deparis, Olivier; Francis, Laurent A

    2016-05-09

    The unique architecture of iridescent Morpho butterfly scales is known to exhibit different optical responses to various vapours. However, the mechanism behind this phenomenon is not fully quantitatively understood. This work reports on process developments in the micro-fabrication of a Morpho-inspired photonic structure in atomic layer deposited (ALD) materials in order to investigate the vapour optical sensitivity of such artificial nanostructures. By developing recipes for dry and wet etching of ALD oxides, we micro-fabricated two structures: one combining Al2O3 and TiO2, and the other combining Al2O3 and HfO2. For the first time, we report the optical response of such ALD Morpho-like structures measured under a controlled flow of either ethanol or isopropyl alcohol (IPA) vapour. In spite of the small magnitude of the effect, the results show a selective vapour response (depending on the materials used).

  19. Vaneless diffusers

    Science.gov (United States)

    Senoo, Y.

    The influence of vaneless diffusers on flow in centrifugal compressors, particularly on surge, is discussed. A vaneless diffuser can demonstrate stable operation in a wide flow range only if it is installed with a backward leaning blade impeller. The circumferential distortion of flow in the impeller disappears quickly in the vaneless diffuser. The axial distortion of flow at the diffuser inlet does not decay easily. In large specific speed compressors, flow out of the impeller is distorted axially. Pressure recovery of diffusers at distorted inlet flow is considerably improved by half guide vanes. The best height of the vanes is a little 1/2 diffuser width. In small specific speed compressors, flow out of the impeller is not much distorted and pressure recovery can be predicted with one-dimensional flow analysis. Wall friction loss is significant in narrow diffusers. The large pressure drop at a small flow rate can cause the positive gradient of the pressure-flow rate characteristic curve, which may cause surging.

  20. Water vapour and ozone profiles in the midlatitude upper troposphere

    Directory of Open Access Journals (Sweden)

    G. Vaughan

    2004-12-01

    Full Text Available We present an investigation of upper tropospheric humidity profiles measured with a standard radiosonde, the Vaisala RS80-A, and a commercial frost-point hygrometer, the Snow White. Modifications to the Snow White, to enable the mirror reflectivity and Peltier cooling current to be monitored during flight, were found to be necessary to determine when the instrument was functioning correctly; a further modification to prevent hydrometeors entering the inlet was also implemented. From 23 combined flights of an ozonesonde, radiosonde and Snow White between September 2001 and July 2002, clear agreement was found between the two humidity sensors, with a mean difference of <2% in relative humidity from 2 to 10 km, and 2.2% between 10 and 13 km. This agreement required a correction to the radiosonde humidity, as described by Miloshevich et al. (2001. Using this result, the dataset of 324 ozonesonde/RS80-A profiles measured from Aberystwyth between 1991 and 2002 was examined to derive statistics for the distribution of water vapour and ozone. Supersaturation with respect to ice was frequently seen at the higher levels – 24% of the time in winter between 8 and 10 km. The fairly uniform distribution of relative humidity persisted to 120% in winter, but decreased rapidly above 100% in summer.

  1. Water vapour and ozone profiles in the midlatitude upper troposphere

    Directory of Open Access Journals (Sweden)

    G. Vaughan

    2005-01-01

    Full Text Available We present an investigation of upper tropospheric humidity profiles measured with a standard radiosonde, the Vaisala RS80-A, and a commercial frost-point hygrometer, the Snow White. Modifications to the Snow White, to enable the mirror reflectivity and Peltier cooling current to be monitored during flight, were found to be necessary to determine when the instrument was functioning correctly; a further modification to prevent hydrometeors entering the inlet was also implemented. From 23 combined flights of an ozonesonde, radiosonde and Snow White between September 2001 and July 2002, clear agreement was found between the two humidity sensors, with a mean difference of <2% in relative humidity from 2 to 10km, and 2.2% between 10 and 13km. This agreement required a correction to the radiosonde humidity, as described by Miloshevich et al. (2001. Using this result, the dataset of 324 ozonesonde/RS80-A profiles measured from Aberystwyth between 1991 and 2002 was examined to derive statistics for the distribution of water vapour and ozone. Supersaturation with respect to ice was frequently seen at the higher levels - 24% of the time in winter between 8 and 10km. The fairly uniform distribution of relative humidity persisted to 120% in winter, but decreased rapidly above 100% in summer.

  2. On The Stability Of Model Flows For Chemical Vapour Deposition

    Science.gov (United States)

    Miller, Robert

    2016-11-01

    The flow in a chemical vapour deposition (CVD) reactor is assessed. The reactor is modelled as a flow over an infinite-radius rotating disk, where the mean flow and convective instability of the disk boundary layer are measured. Temperature-dependent viscosity and enforced axial flow are used to model the steep temperature gradients present in CVD reactors and the pumping of the gas towards the disk, respectively. Increasing the temperature-dependence parameter of the fluid viscosity (ɛ) results in an overall narrowing of the fluid boundary layer. Increasing the axial flow strength parameter (Ts) accelerates the fluid both radially and axially, while also narrowing the thermal boundary layer. It is seen that when both effects are imposed, the effects of axial flow generally dominate those of the viscosity temperature dependence. A local stability analysis is performed and the linearized stability equations are solved using a Galerkin projection in terms of Chebyshev polynomials. The neutral stability curves are then plotted for a range of ɛ and Ts values. Preliminary results suggest that increasing Ts has a stabilising effect on both type I and type II stationary instabilities, while small increases in ɛ results in a significant reduction to the critical Reynolds number.

  3. Poly(methyl methacrylate) films for organic vapour sensing

    CERN Document Server

    Capan, R; Hassan, A K; Tanrisever, T

    2003-01-01

    Optical constants and fabrication parameters are investigated using surface plasmon resonance (SPR) studies on spun films of poly(methyl methacrylate) (PMMA) derivatives in contact with two different dielectric media. A value of 1.503 for the refractive index of PMMA films produced from a solution having concentration of 1 mg ml sup - sup 1 at the speed of 3000 rpm is in close agreement with the data obtained from ellipsometric measurements. The film thickness shows a power-law dependence on the spin speed but the thickness increases almost linearly with the concentration of the spreading solution. These results are in good agreement with the hydrodynamic theory for a low-viscosity and highly volatile liquid. On the basis of SPR measurements under dynamic conditions, room temperature response of PMMA films to benzene vapours is found to be fast, highly sensitive and reversible. The sensitivity of detection of toluene, ethyl benzene and m-xylene is much smaller than that of benzene.

  4. Reducing chemical vapour infiltration time for ceramic matrix composites.

    Science.gov (United States)

    Timms, L. A.; Westby, W.; Prentice, C.; Jaglin, D.; Shatwell, R. A.; Binner, J. G. P.

    2001-02-01

    Conventional routes to producing ceramic matrix composites (CMCs) require the use of high temperatures to sinter the individual ceramic particles of the matrix together. Sintering temperatures are typically much higher than the upper temperature limits of the fibres. This paper details preliminary work carried out on producing a CMC via chemical vapour infiltration (CVI), a process that involves lower processing temperatures, thus avoiding fibre degradation. The CVI process has been modified and supplemented in an attempt to reduce the CVI process time and to lower the cost of this typically expensive process. To this end microwave-enhanced CVI (MECVI) has been chosen, along with two alternative pre-infiltration steps: electrophoretic infiltration and vacuum bagging. The system under investigation is based on silicon carbide fibres within a silicon carbide matrix (SiCf/SiC). The results demonstrate that both approaches result in an enhanced initial density and a consequent significant reduction in the time required for the MECVI processing step. Dual energy X-ray absorptiometry was used as a non-destructive, density evaluation technique. Initial results indicate that the presence of the SiC powder in the pre-form changes the deposition profile during the MECVI process.

  5. Water vapour in the atmosphere of a transiting extrasolar planet.

    Science.gov (United States)

    Tinetti, Giovanna; Vidal-Madjar, Alfred; Liang, Mao-Chang; Beaulieu, Jean-Philippe; Yung, Yuk; Carey, Sean; Barber, Robert J; Tennyson, Jonathan; Ribas, Ignasi; Allard, Nicole; Ballester, Gilda E; Sing, David K; Selsis, Franck

    2007-07-12

    Water is predicted to be among the most abundant (if not the most abundant) molecular species after hydrogen in the atmospheres of close-in extrasolar giant planets ('hot Jupiters'). Several attempts have been made to detect water on such planets, but have either failed to find compelling evidence for it or led to claims that should be taken with caution. Here we report an analysis of recent observations of the hot Jupiter HD 189733b (ref. 6) taken during the transit, when the planet passed in front of its parent star. We find that absorption by water vapour is the most likely cause of the wavelength-dependent variations in the effective radius of the planet at the infrared wavelengths 3.6 mum, 5.8 mum (both ref. 7) and 8 mum (ref. 8). The larger effective radius observed at visible wavelengths may arise from either stellar variability or the presence of clouds/hazes. We explain the report of a non-detection of water on HD 189733b (ref. 4) as being a consequence of the nearly isothermal vertical profile of the planet's atmosphere.

  6. Adsorption Of Water And Benzene Vapour In Mesoporous Materials

    Directory of Open Access Journals (Sweden)

    Paulina Taba

    2008-11-01

    Full Text Available Mesoporous materials have attracted the attention of many researchers due to the potential applications promised by the materials. This article discusses adsorption of water and benzene vapour in mesoporous materials (mesoporous silica: MCM-41, MCM-48 and their modification. MCM-41 and MCM-48 were synthesized hydrothermally at 100 oC using cethyltrimethylammonium chloride or dodecyltrimethylammonium bromide for MCM-41 (C16 or MCM-41 (C12 respectively and a mixture of cethyltrimethylammonium bromide and Triton X-100 for MCM-48 as templates. Their modifications were conducted by silylation of MCM-41 (C16 and MCM-48 with trimethylchloro silane (MCM16-TMCS and MCM48-TMCS and t-butyldimethylchloro silane (MCM16-TBDMCS and MCM48-TBDMCS. Results showed that MCM-41 and MCM-48 materials had hydrophobic features which were shown in the small amount of water adsorption at low P/P0. The hydrophobicity of samples used in this study decrease in the sequence: MCM-41 (C16 > MCM-48 > MCM-41 (C12. The hydrophobicity increased when MCM-41 and MCM-48 were silylated with TMCS or TBDMCS. All unsilylated MCM materials show higher affinity to benzene at low P/P0 than the silylated samples. The results of water and benzene adsorption showed that silylated samples are promising candidates as selective adsorbents for organic compounds.

  7. The atmospheric chemical vapour deposition of coatings on glass

    CERN Document Server

    Sanderson, K D

    1996-01-01

    The deposition of thin films of indium oxide, tin doped indium oxide (ITO) and titanium nitride for solar control applications have been investigated by Atmospheric Chemical Vapour Deposition (APCVD). Experimental details of the deposition system and the techniques used to characterise the films are presented. Results from investigations into the deposition parameters, the film microstructure and film material properties are discussed. A range of precursors were investigated for the deposition of indium oxide. The effect of pro-mixing the vaporised precursor with an oxidant source and the deposition temperature has been studied. Polycrystalline In sub 2 O sub 3 films with a resistivity of 1.1 - 3x10 sup - sup 3 OMEGA cm were obtained with ln(thd) sub 3 , oxygen and nitrogen. The growth of ITO films from ln(thd) sub 3 , oxygen and a range of tin dopants is also presented. The effect of the dopant precursor, the doping concentration, deposition temperature and the effect of additives on film growth and microstr...

  8. Accuracy of seven vapour intrusion algorithms for VOC in groundwater

    Energy Technology Data Exchange (ETDEWEB)

    Provoost, Jeroen; Bronders, Jan; Seuntjens, Piet [Flemish Inst. for Technological Research (VITO), Mol (Belgium); Reijnders, Lucas [Dept. of Science, Open Univ. Netherlands (OU NL), Heerlen (Netherlands); Swartjes, Frank; Lijzen, Johannes [National Inst. for Public Health and the Environment (RIVM), Bilthoven (Netherlands)

    2009-02-15

    During the last decade, soil contamination with volatile organic contaminants (VOC) received special attention because of their potential to cause indoor air problems. Moreover, research has shown that people spend 64% to 94% of there time indoors; therefore, the indoor air quality is of a primary importance for exposure to VOC. Human health risks to VOC-in cases of soil contamination-are often dominated by the exposure route 'inhalation of indoor air'. Exposure is often a result of vapour transport from the soil or groundwater to the indoor air of the building. Within human health risk assessments, a variety of algorithms are available that calculate transfer of soil gas to the indoor air. These algorithms suffer from a relatively high uncertainty due to a lack of representation of spatial and temporal variability. For such an application, these algorithms need to be further verified empirically against field observations so that they can be sufficiently reliable for regulatory purposes. This paper presents the accuracy for seven algorithms by using observed and predicted soil and indoor air concentrations from three sites, where the groundwater had been contaminated with aromatic and chlorinated VOC. (orig.)

  9. Efficient planar heterojunction perovskite solar cells by vapour deposition.

    Science.gov (United States)

    Liu, Mingzhen; Johnston, Michael B; Snaith, Henry J

    2013-09-19

    Many different photovoltaic technologies are being developed for large-scale solar energy conversion. The wafer-based first-generation photovoltaic devices have been followed by thin-film solid semiconductor absorber layers sandwiched between two charge-selective contacts and nanostructured (or mesostructured) solar cells that rely on a distributed heterojunction to generate charge and to transport positive and negative charges in spatially separated phases. Although many materials have been used in nanostructured devices, the goal of attaining high-efficiency thin-film solar cells in such a way has yet to be achieved. Organometal halide perovskites have recently emerged as a promising material for high-efficiency nanostructured devices. Here we show that nanostructuring is not necessary to achieve high efficiencies with this material: a simple planar heterojunction solar cell incorporating vapour-deposited perovskite as the absorbing layer can have solar-to-electrical power conversion efficiencies of over 15 per cent (as measured under simulated full sunlight). This demonstrates that perovskite absorbers can function at the highest efficiencies in simplified device architectures, without the need for complex nanostructures.

  10. Vapour and air bubble collapse analysis in viscous compressible water

    Directory of Open Access Journals (Sweden)

    Gil Bazanini

    2001-01-01

    Full Text Available Numerical simulations of the collapse of bubbles (or cavities are shown, using the finite difference method, taking into account the compressibility of the liquid, expected to occur in the final stages of the collapse process. Results are compared with experimental and theoretical data for incompressible liquids, to see the influence of the compressibility of the water in the bubble collapse. Pressure fields values are calculated in an area of 800 x 800 mm, for the case of one bubble under the hypothesis of spherical symmetry. Results are shown as radius versus time curves for the collapse (to compare collapse times, and pressure curves in the plane, for pressure fields. Such calculations are new because of their general point of view, since the existing works do not take into account the existence of vapour in the bubble, neither show the pressure fields seen here. It is also expected to see the influence of the compressibility of the water in the collapse time, and in the pressure field, when comparing pressure values.

  11. The technology of Plasma Spray Physical Vapour Deposition

    Directory of Open Access Journals (Sweden)

    M. Góral

    2012-12-01

    Full Text Available Purpose: The deposition of thermal barrier coatings is currently the most effective means of protecting the surface of aircraft engine turbine blades from the impact of aggressive environment of combustion gases. The new technologies of TBC depositions are required.Design/methodology/approach: The essential properties of the PS-PVD process have been outlined, as well as recent literature references. In addition, the influence of a set process condition on the properties of the deposited coatings has been described.Findings: The new plasma-spraying PS-PVD method is a promising technology for the deposition of modern thermal barrier coatings on aircraft engine turbine blades.Research limitations/implications: The constant progress of engine operating temperatures and increasing pollution restrictions determine the intensive development of heat-resistant coatings, which is directed to new deposition technologies and coating materials.Practical implications: The article presents a new technology of thermal barrier coating deposition - LPPS Thin Film and Plasma Spray - Physical Vapour Deposition.Originality/value: The completely new technologies was described in article.

  12. Controlled oxidation of iron nanoparticles in chemical vapour synthesis

    Science.gov (United States)

    Ruusunen, Jarno; Ihalainen, Mika; Koponen, Tarmo; Torvela, Tiina; Tenho, Mikko; Salonen, Jarno; Sippula, Olli; Joutsensaari, Jorma; Jokiniemi, Jorma; Lähde, Anna

    2014-02-01

    In the present study, iron oxide nanoparticles (primary particle size of 80-90 nm) with controlled oxidation state were prepared via an atmospheric pressure chemical vapour synthesis (APCVS) method. Iron pentacarbonyl [Fe(CO)5], a precursor material, was thermally decomposed to iron in the APCVS reactor. Subsequently, the iron was oxidized with controlled amount of oxygen in the reactor to produce nearly pure magnetite or haematite particles depending on the oxygen concentration. Size, morphology and crystal structure of the synthesized nanoparticles were studied with scanning mobility particle sizer (SMPS), transmission electron microscopy (TEM) and X-ray diffraction (XRD). In addition, thermodynamic equilibrium calculations and computational fluid dynamics model were used to predict the oxidation state of the iron oxides and the reaction conditions during mixing. Aggregates of crystalline particles were formed, determined as magnetite at the oxygen volumetric fraction of 0.1 % and haematite at volumetric fraction of 0.5 %, according to the XRD. The geometric mean electrical mobility diameter of the aggregates increased from 110 to 155 nm when the volumetric fraction of oxygen increased from 0.1 to 0.5 %, determined using the SMPS. The aggregates were highly sintered based on TEM analyses. As a conclusion, APCVS method can be used to produce nearly pure crystalline magnetite or haematite nanoparticles with controlled oxidation in a continuous one-stage gas-phase process.

  13. Tungsten Deposition on Graphite using Plasma Enhanced Chemical Vapour Deposition.

    Science.gov (United States)

    Sharma, Uttam; Chauhan, Sachin S.; Sharma, Jayshree; Sanyasi, A. K.; Ghosh, J.; Choudhary, K. K.; Ghosh, S. K.

    2016-10-01

    The tokamak concept is the frontrunner for achieving controlled thermonuclear reaction on earth, an environment friendly way to solve future energy crisis. Although much progress has been made in controlling the heated fusion plasmas (temperature ∼ 150 million degrees) in tokamaks, technological issues related to plasma wall interaction topic still need focused attention. In future, reactor grade tokamak operational scenarios, the reactor wall and target plates are expected to experience a heat load of 10 MW/m2 and even more during the unfortunate events of ELM's and disruptions. Tungsten remains a suitable choice for the wall and target plates. It can withstand high temperatures, its ductile to brittle temperature is fairly low and it has low sputtering yield and low fuel retention capabilities. However, it is difficult to machine tungsten and hence usages of tungsten coated surfaces are mostly desirable. To produce tungsten coated graphite tiles for the above-mentioned purpose, a coating reactor has been designed, developed and made operational at the SVITS, Indore. Tungsten coating on graphite has been attempted and successfully carried out by using radio frequency induced plasma enhanced chemical vapour deposition (rf -PECVD) for the first time in India. Tungsten hexa-fluoride has been used as a pre-cursor gas. Energy Dispersive X-ray spectroscopy (EDS) clearly showed the presence of tungsten coating on the graphite samples. This paper presents the details of successful operation and achievement of tungsten coating in the reactor at SVITS.

  14. Laser diagnostics of chemical vapour deposition of diamond films

    CERN Document Server

    Wills, J B

    2002-01-01

    Cavity ring down spectroscopy (CRDS) has been used to make diagnostic measurements of chemically activated CH sub 4 / H sub 2 gas mixtures during the chemical vapour deposition (CVD) of thin diamond films. Absolute absorbances, concentrations and temperatures are presented for CH sub 3 , NH and C sub 2 H sub 2 in a hot filament (HF) activated gas mixture and CH, C sub 2 and C sub 2 H sub 2 in a DC arc plasma jet activated mixture. Measurements of the radical species were made using a pulsed dye laser system to generate tuneable visible and UV wavelengths. These species have greatest concentration in the hottest, activated regions of the reactors. Spatial profiling of the number densities of CH sub 3 and NH radicals have been used as stringent tests of predictions of radical absorbance and number densities made by 3-D numerical simulations, with near quantitative agreement. O sub 2 has been shown to reside in the activated region of the Bristol DC arc jet at concentrations (approx 10 sup 1 sup 3 molecules / cm...

  15. Water vapour in the atmosphere of a transiting extrasolar planet

    CERN Document Server

    Tinetti, Giovanna; Liang, Mao-Chang; Beaulieu, Jean-Philippe; Yung, Yuk; Carey, Sean; Barber, Robert J; Tennyson, Jonathan; Ribas, Ignasi; Allard, Nicole; Ballester, Gilda E; Sing, David K; Selsis, Franck

    2007-01-01

    Water is predicted to be among, if not the most abundant molecular species after hydrogen in the atmospheres of close-in extrasolar giant planets (hot-Jupiters) Several attempts have been made to detect water on an exoplanet, but have failed to find compelling evidence for it or led to claims that should be taken with caution. Here we report an analysis of recent observations of the hot-Jupiter HD189733b taken during the transit, where the planet passed in front of its parent star. We find that absorption by water vapour is the most likely cause of the wavelength-dependent variations in the effective radius of the planet at the infrared wavelengths 3.6, 5.8 and 8 microns. The larger effective radius observed at visible wavelengths may be due to either star variability or the presence of clouds/hazes. We explain the most recent thermal infrared observations of the planet during secondary transit behind the star, reporting a non-detection of water on HD189733b, as being a consequence of the nearly isothermal ve...

  16. Vapour phase synthesis of salol over solid acids via transesterification

    Indian Academy of Sciences (India)

    S Z Mohamed Shamshuddin; N Nagaraju

    2010-03-01

    The transesterification of methyl salicylate with phenol has been studied in vapour phase over solid acid catalysts such as ZrO2, MoO3 and SO$^{2-}_{4}$ or Mo(VI) ions modified zirconia. The catalytic materials were prepared and characterized for their total surface acidity, BET surface area and powder XRD patterns. The effect of mole-ratio of the reactants, catalyst bed temperature, catalyst weight, flowrate of reactants, WHSV and time-on-stream on the conversion (%) of phenol and selectivity (%) of salol has been investigated. A good yield (up to 70%) of salol with 90% selectivity was observed when the reactions were carried out at a catalyst bed temperature of 200°C and flow-rate of 10 mL/h in presence of Mo(VI)/ZrO2 as catalyst. The results have been interpreted based on the variation of acidic properties and powder XRD phases of zirconia on incorporation of SO$^{2-}_{4}$ or Mo(VI) ions. The effect of poisoning of acid sites of SO$^{2-}_{4}$ or Mo(VI) ions modified zirconia on total surface acidity, powder XRD phases and catalytic activity was also studied. Possible reaction mechanisms for the formation of salol and diphenyl ether over acid sites are proposed.

  17. Vapour transport of rare earth elements (REE) in volcanic gas: Evidence from encrustations at Oldoinyo Lengai

    Science.gov (United States)

    Gilbert, C. D.; Williams-Jones, A. E.

    2008-10-01

    Fumarolic encrustations and natrocarbonatite lava from the active crater of Oldoinyo Lengai volcano, Tanzania, were sampled and analysed. Two types of encrustation were distinguished on the basis of their REE content, enriched (~ 2800-5600 × [REE chondrite]) and depleted (~ 100-200 × [REE chondrite]) relative to natrocarbonatite (1700-1900 × [REE chondrite]. REE-enriched encrustations line the walls of actively degassing fumaroles, whereas REE-depleted encrustations occur mainly along cracks in and as crusts on cooling natrocarbonatite lava flows; one of the low REE encrustation samples was a stalactite from the wall of a possible fumarole. The encrustations are interpreted to have different origins, the former precipitating from volcanic gas and the latter from meteoric/ground water converted to steam by the heat of the overlying lava flow(s). REE-profiles of encrustations and natrocarbonatite are parallel, suggesting that there was no preferential mobilization of specific REE by either volcanic vapour or meteoric water vapour. The elevated REE-content of the first group of encrustations suggests that direct REE-transport from natrocarbonatite to volcanic vapour is possible. The REE trends observed in samples precipitating directly from the volcanic vapour cannot be explained by dry volatility based on the available data as there is no evidence in the encrustation compositions of the greatly enhanced volatility predicted for Yb and Eu. The observed extreme REE-fractionation with steep La/Sm slopes parallel to those of the natrocarbonatite reflects solvation and complexation reactions in the vapour phase that did not discriminate amongst the different REE or similar transport of REE in both the natrocarbonatite magma and its exsolving vapour. The low concentrations of REE in the encrustations produced by meteoric vapour suggest that the temperature was too low or that this vapour did not contain the ligands necessary to permit significant mobilization of the REE.

  18. Vapour phase corrosion inhibitors from South African renewable resources and their evaluation

    CSIR Research Space (South Africa)

    Vuorinen, E

    2006-02-01

    Full Text Available ) in an environment depends on the vapour pressure of the compounds. Suitable chemicals from the petroleum industry are used as corrosion inhibitors but often chemicals from renewable resources have been overlooked. Furfural is produced from bagasse (a by... of amines proved to be excellent VCIs for mild steel. Screening of potential VCIs from furfural and furfural derivatives will be done using thermogravimetry. Vapour Phase Corrosion Inhibitors from South African Renewable Resources and their Evaluation...

  19. The influence of moisture content on the water vapour resistance of surface coated spruce

    DEFF Research Database (Denmark)

    Engelund, E.T.; Ulriksen, L.; Hansen, Kurt Kielsgaard

    2005-01-01

    , but now with one layer of paint (60 g/m^2) on one surface of the wood specimens. The results show that the RH level significantly influences the water vapour resistance of the paint. For wet cup tests a water vapour resistance of the paint of 6.5•10^8 Pa•m^2•s/kg in average is found. In contrast...

  20. Stratospheric water vapour in the vicinity of the Arctic polar vortex

    Directory of Open Access Journals (Sweden)

    M. Maturilli

    2006-07-01

    Full Text Available The stratospheric water vapour mixing ratio inside, outside, and at the edge of the polar vortex has been accurately measured by the FLASH-B Lyman-Alpha hygrometer during the LAUTLOS campaign in Sodankylä, Finland, in January and February 2004. The retrieved H2O profiles reveal a detailed view on the Arctic lower stratospheric water vapour distribution, and provide a valuable dataset for the validation of model and satellite data. Analysing the measurements with the semi-lagrangian advection model MIMOSA, water vapour profiles typical for the polar vortex' interior and exterior have been identified, and laminae in the observed profiles have been correlated to filamentary structures in the potential vorticity field. Applying the validated MIMOSA transport scheme to specific humidity fields from operational ECMWF analyses, large discrepancies from the observed profiles arise. Although MIMOSA is able to reproduce weak water vapour filaments and improves the shape of the profiles compared to operational ECMWF analyses, both models reveal a dry bias of about 1 ppmv in the lower stratosphere above 400 K, accounting for a relative difference from the measurements in the order of 20%. The large dry bias in the analysis representation of stratospheric water vapour in the Arctic implies the need for future regular measurements of water vapour in the polar stratosphere to allow the validation and improvement of climate models.

  1. Influence of metal vapour on arc temperatures in gas-metal arc welding: convection versus radiation

    Science.gov (United States)

    Murphy, Anthony B.

    2013-06-01

    The presence of metal vapour in gas-metal arc welding has been shown to have two strong effects on the arc plasma: a decrease in temperature throughout the arc, and the formation of a local temperature minimum near the arc axis. These effects have been attributed, on the basis of different computational models, to either the increased radiative emission associated with the presence of metal vapour in the arc plasma, or the influence of the metal vapour influx on convective flow in the arc. This question is investigated using a three-dimensional computational model in which the production and the transport of metal vapour are taken into account self-consistently. Parameters relevant to welding of thin sheets of aluminum are examined. For these conditions, it is found that the first effect (the decrease in temperature throughout the arc) is due to both the increased radiative emission and the influence of the metal vapour influx on flow. The second effect (the local temperature minimum, which in this case occurs just below the wire electrode) is a consequence of the influence of aluminum vapour produced from the wire electrode on flow in the arc. By examining published results and the energy balance in the plasma, it is shown that for welding of steel with higher arc currents, the increased radiative emission can lead to a local temperature minimum at a greater distance from the wire electrode.

  2. Stratospheric water vapour in the vicinity of the Arctic polar vortex

    Energy Technology Data Exchange (ETDEWEB)

    Maturilli, M. [Alfred Wegener Institute for Polar and Marine Research, Potsdam (Germany); Fierli, F. [CNR (Italy). Inst. for Atmospheric Sciences and Climate; Yushkov, V.; Lukyanov, A.; Khaykin, S. [Central Aerological Observatory, Moscow (Russian Federation); Hauchecorne, A. [CNRS, Verrieres-le-Buisson (France). Service d' Aeronomie

    2006-07-01

    The stratospheric water vapour mixing ratio inside, outside, and at the edge of the polar vortex has been accurately measured by the FLASH-B Lyman-Alpha hygrometer during the LAUTLOS campaign in Sodankylae, Finland, in January and February 2004. The retrieved H{sub 2}O profiles reveal a detailed view on the Arctic lower stratospheric water vapour distribution, and provide a valuable dataset for the validation of model and satellite data. Analysing the measurements with the semi-lagrangian advection model MIMOSA, water vapour profiles typical for the polar vortex' interior and exterior have been identified, and laminae in the observed profiles have been correlated to filamentary structures in the potential vorticity field. Applying the validated MIMOSA transport scheme to specific humidity fields from operational ECMWF analyses, large discrepancies from the observed profiles arise. Although MIMOSA is able to reproduce weak water vapour filaments and improves the shape of the profiles compared to operational ECMWF analyses, both models reveal a dry bias of about 1 ppmv in the lower stratosphere above 400 K, accounting for a relative difference from the measurements in the order of 20%. The large dry bias in the analysis representation of stratospheric water vapour in the Arctic implies the need for future regular measurements of water vapour in the polar stratosphere to allow the validation and improvement of climate models. (orig.)

  3. SO2/Hg removal from flue gas by dry FGD

    Institute of Scientific and Technical Information of China (English)

    Wang Fan; Wang Hongmei; Zhang Fan; Zhu Jinwei; Tian Gang; Liu Yu; Mao Jixian

    2012-01-01

    To study the mechanism of SO2 and Hg removal from flue gas,an experimental packed bed reactor was designed to simulate the dry FGD,where a mixture of lime and fly ash in ratio 1∶3 w/w was used as the SO2 and Hg sorbent,and steam at temperature of 100 ℃ was applied for activation of the sorbent,while the activation time set to 20 min.The experimental factors including the SO2/Hg sorbent characteristics,50% breakthrough time for SO2/Hg removal,sorbent packed bed depth and reaction temperature were investigated.The experimental results show that after steam activation,the BET specific surface area and specific pore volume increased from 37.8 to 45.5 m2/g and from 0.42 to 0.51 cm3/g,respectively.With activation of the sorbent by steam,the 50% breakthrough times of SO2 and Hg removal increased from 34 to 42 min and from 23 to 45 min,respectively.When the packed bed depth was increased from 5 to 25 mm,the 50% breakthrough times for Hg and SO2 removal increased from 12 to 52 min and from 6 to 47 min,respectively.With the increase of the reaction temperature,the 50% breakthrough of SO2/Hg removal decreased accordingly.Steam activation can efficiently improve SO2/Hg removal simultaneously.

  4. Low field magnetoresistance in a 2D topological insulator based on wide HgTe quantum well

    Science.gov (United States)

    Olshanetsky, E. B.; Kvon, Z. D.; Gusev, G. M.; Mikhailov, N. N.; Dvoretsky, S. A.

    2016-09-01

    Low field magnetoresistance is experimentally studied in a two-dimensional topological insulator (TI) in both diffusive and quasiballistic samples fabricated on top of a wide (14 nm) HgTe quantum well. In all cases a pronounced quasi-linear positive magnetoresistance is observed similar to that found previously in diffusive samples based on a narrow (8 nm) HgTe well. The experimental results are compared with the main existing theoretical models based on different types of disorder: sample edge roughness, nonmagnetic disorder in an otherwise coherent TI and metallic puddles due to locally trapped charges that act like local gate on the sample. The quasiballistic samples with resistance close to the expected quantized values also show a positive low-field magnetoresistance but with a pronounced admixture of mesoscopic effects.

  5. [Differentiated treatment of acute diffuse brain injuries].

    Science.gov (United States)

    Pedachenko, E G; Dziak, L A; Sirko, A G

    2012-01-01

    Diagnosis and treatment results of 57 patients with acute diffuse brain injury have been analyzed. Patients were divided into two groups: first study period 2000-2005; second study period 2006-2010. The main differences between the first and the second study periods were in health condition and brain functions monitoring parameters, therapy approaches and goals. Increasing of axial and lateral dislocation symptoms during progression from the first type of diffuse injury to the fourth one is related to intracranial hypertension (ICH) occurrence rate and significance it's significance. During the second study period, ICH was found in 25% patients with the second type of injury, 57% patients with the third type of injury, and 80%, with the fourth type of injury. Mean ICP in the group of patients with the second type of diffuse injury comprised 14.4 +/- 6.6 mmHg; with the third type of injury, 30 +/- 20.6 mmHg; with the fourth type of injuty, 37.6 +/- 14.1 mmHg. Introduction of differentiated approach to conservative or surgical treatment method application to acute diffuse brain injuries patients based on ICP monitoring data led to 13.8% reduction in mortality in the second study period compared with the first study period.

  6. Characterization of the Microstructure of HgCdTe with p-Type Doping

    Science.gov (United States)

    Lobre, C.; Jouneau, P.-H.; Mollard, L.; Ballet, P.

    2014-08-01

    Nitrogen, phosphorus, arsenic, and antimony ions were implanted in Hg0.3Cd0.7Te (MCT) layers under the same implantation conditions. An identical annealing process was then applied to these layers to eradicate implantation damage and to activate the impurities. Implantation damage was investigated by direct visualization, by use of bright-field scanning transmission electron microscopy (BF-STEM). Secondary-ion mass spectrometry was used to investigate impurity diffusion on annealing. The combination of these two techniques revealed the significant effect of structural implantation damage on the diffusion process. Annealed layers were then investigated by high-resolution STEM imaging and energy-dispersive x-ray spectroscopy in STEM (STEM-EDX). This approach enables direct visualization and, therefore, further description of arsenic and antimony-rich nanocrystals.

  7. Recent progress in the doping of MBE HgCdTe

    Science.gov (United States)

    Sivananthan, Sivalingam; Wijewarnasuriya, P. S.; Faurie, Jean-Pierre

    1995-09-01

    We present a review of the recent progress in the doping of HgCdTe grown by molecular beam epitaxy. A detailed analysis of the unintentional/intrinsic, n-type, and p-type doping is presented. Our results show that CdZnTe substrates should be carefully screened to reduce the out-diffusion of impurities from the substrate. N-type HgCdTe layers exhibit excellent Hall characteristics down to indium levels of 2 X 10(superscript 15) cm(superscript -3). Electron mobilities in the range of (2 - 3) X 10(superscript 5) cm(superscript 2)/vs at 23 K were obtained. Measured lifetime data fits very well with the intrinsic band-to-band recombination. However, below 2 X 10(superscript 15) cm(superscript -3) doping levels, minority carrier lifetime is limited by Schockley-Reed recombination. We have implemented planar doping with arsenic as p-type dopant during MBE growth. Our results clearly indicate that arsenic incorporates as an acceptor dopant during the growth of MBE HgCdTe.

  8. WAVE-E: The WAter Vapour European-Explorer Mission

    Science.gov (United States)

    Jimenez-LLuva, David; Deiml, Michael; Pavesi, Sara

    2017-04-01

    In the last decade, stratosphere-troposphere coupling processes in the Upper Troposphere Lower Stratosphere (UTLS) have been increasingly recognized to severely impact surface climate and high-impact weather phenomena. Weakened stratospheric circumpolar jets have been linked to worldwide extreme temperature and high-precipitation events, while anomalously strong stratospheric jets can lead to an increase in surface winds and tropical cyclone intensity. Moreover, stratospheric water vapor has been identified as an important forcing for global decadal surface climate change. In the past years, operational weather forecast and climate models have adapted a high vertical resolution in the UTLS region in order to capture the dynamical processes occurring in this highly stratified region. However, there is an evident lack of available measurements in the UTLS region to consistently support these models and further improve process understanding. Consequently, both the IPCC fifth assessment report and the ESA-GEWEX report 'Earth Observation and Water Cycle Science Priorities' have identified an urgent need for long-term observations and improved process understanding in the UTLS region. To close this gap, the authors propose the 'WAter Vapour European - Explorer' (WAVE-E) space mission, whose primary goal is to monitor water vapor in the UTLS at 1 km vertical, 25 km horizontal and sub-daily temporal resolution. WAVE-E consists of three quasi-identical small ( 500 kg) satellites (WAVE-E 1-3) in a constellation of Sun-Synchronous Low Earth Orbits, each carrying a limb sounding and cross-track scanning mid-infrared passive spectrometer (824 cm-1 to 829 cm-1). The core of the instruments builds a monolithic, field-widened type of Michelson interferometer without any moving parts, rendering it rigid and fault tolerant. Synergistic use of WAVE-E and MetOp-NG operational satellites is identified, such that a data fusion algorithm could provide water vapour profiles from the

  9. Determination of MeHg sources to fish in the St. Louis River, MN, USA, using Hg stable isotopes

    Science.gov (United States)

    Mercury contamination in the Great Lakes region has become a prevalent concern due to elevated methylmercury (MeHg) levels in fish. While atmospheric deposition of Hg is ubiquitous, releases from legacy point-sources give rise to numerous Areas of Concern (AOCs) across the Great ...

  10. Tracing anthropogenic Hg and Pb input using stable Hg and Pb isotope ratios in sediments of the central Portuguese Margin

    NARCIS (Netherlands)

    Mil-Holmens, M.; Blum, J.; Canário, J.; Caetano, M.; Costa, A.M.; Lebreiro, S.M.; Trancoso, M.; Richter, T.O.; de Stigter, H.; Johnson, M.; Branco, V.; Cesário, R.; Mouro, F.; Mateus, M.; Boer, W.; Melo, Z.

    2013-01-01

    Three short marine sediment cores from the Cascais Submarine Canyon (CSC; cores 252-32 and 252-35) and the Estremadura Spur (core 252-16) on the central Portuguese Margin were analysed for Hg, Pb, Al, and Mn concentrations, and both Pb and Hg stable isotope compositions, in order to reconstruct tren

  11. Biogeochemical factors affecting the distribution, speciation, and transport of Hg species in the Deûle and Lys Rivers (Northern France).

    Science.gov (United States)

    Daye, Mirna; Kadlecova, Milada; Ouddane, Baghdad

    2015-02-01

    in all sites is produced in situ rather than exported from other potential sources confirmed by significant relations of % MeHg with %Corg and AVS. Hg pollution is transported from the Deûle River to the Lys River (L-C and L-D) through suspended particles leached or remobilized from the River catchment. The dominance of reducing conditions in the Deûle River attributed to higher sulfide concentration has contributed to higher HgTPW than the Lys sites. Diffusive fluxes of HgT from sediment to water column for the Deûle and Lys River sites (L-C and L-D) were estimated to be 224, 53, and 2 ng/cm(2) year, respectively.

  12. Exposure to oil mist and oil vapour during offshore drilling in Norway, 1979-2004

    Energy Technology Data Exchange (ETDEWEB)

    Steinsvag, K.; Bratveit, M.; Moen, B.E. [University of Bergen (Norway). Dept. of Public Health and Primary Health Care

    2006-07-01

    Objectives: To describe personal exposure to airborne hydrocarbon contaminants (oil mist and oil vapour) from 1979 to 2004 in the mud-handling areas of offshore drilling facilities operating on the Norwegian continental shelf when drilling with oil-based muds. Methods: Qualitative and quantitative information was gathered during visits to companies involved in offshore oil and gas production in Norway. Monitoring reports on oil mist and oil vapour exposure covered 37 drilling facilities. Exposure data were analysed using descriptive statistics and by constructing linear mixed-effects models. Results: Samples had been taken during the use of three generations of hydrocarbon base oils, namely diesel oils (1979-1984), low-aromatic mineral oils (1985-1997) and non-aromatic mineral oils (1998-2004). Sampling done before 1984 showed high exposure to diesel vapour (arithmetic mean, AM = 1217 mg m{sup -3}). When low-aromatic mineral oils were used, the exposure to oil mist and oil vapour was 4.3 and 36 mg m{sup -3}, and the respective AMs for non-aromatic mineral oils were reduced to 0.54 and 16 mg m{sup -3}. Downward time trends were indicated for both oil mist (6% per year) and oil vapour (8% per year) when the year of monitoring was introduced as a fixed effect in a linear mixed-effects model analysis. Rig type, technical control measures and mud temperature significantly determined exposure to oil mist. Rig type, type of base oil, viscosity of the base oil, work area, mud temperature and season significantly determined exposure to oil vapour. Major decreases in variability were found for the between-rig components. Conclusions: Exposure to oil mist and oil vapour declined over time in the mud-handling areas of offshore drilling facilities. Exposure levels were associated with rig type, mud temperature, technical control measures, base oil, viscosity of the base oil, work area and season. (author)

  13. Continuous measurements of isotopic composition of water vapour on the East Antarctic Plateau

    Science.gov (United States)

    Casado, Mathieu; Landais, Amaelle; Masson-Delmotte, Valérie; Genthon, Christophe; Kerstel, Erik; Kassi, Samir; Arnaud, Laurent; Picard, Ghislain; Prie, Frederic; Cattani, Olivier; Steen-Larsen, Hans-Christian; Vignon, Etienne; Cermak, Peter

    2016-07-01

    Water stable isotopes in central Antarctic ice cores are critical to quantify past temperature changes. Accurate temperature reconstructions require one to understand the processes controlling surface snow isotopic composition. Isotopic fractionation processes occurring in the atmosphere and controlling snowfall isotopic composition are well understood theoretically and implemented in atmospheric models. However, post-deposition processes are poorly documented and understood. To quantitatively interpret the isotopic composition of water archived in ice cores, it is thus essential to study the continuum between surface water vapour, precipitation, surface snow and buried snow. Here, we target the isotopic composition of water vapour at Concordia Station, where the oldest EPICA Dome C ice cores have been retrieved. While snowfall and surface snow sampling is routinely performed, accurate measurements of surface water vapour are challenging in such cold and dry conditions. New developments in infrared spectroscopy enable now the measurement of isotopic composition in water vapour traces. Two infrared spectrometers have been deployed at Concordia, allowing continuous, in situ measurements for 1 month in December 2014-January 2015. Comparison of the results from infrared spectroscopy with laboratory measurements of discrete samples trapped using cryogenic sampling validates the relevance of the method to measure isotopic composition in dry conditions. We observe very large diurnal cycles in isotopic composition well correlated with temperature diurnal cycles. Identification of different behaviours of isotopic composition in the water vapour associated with turbulent or stratified regime indicates a strong impact of meteorological processes in local vapour/snow interaction. Even if the vapour isotopic composition seems to be, at least part of the time, at equilibrium with the local snow, the slope of δD against δ18O prevents us from identifying a unique origin leading

  14. A simple model of oxygen diffusion out of the retinal artery

    Science.gov (United States)

    Beach, J. M.; Ning, J.; Khoobehi, B.; Rice, D. A.

    2009-02-01

    The purpose of this study is to explore the possibility that oxygen (O2) diffusion out of the retinal artery (RA) can explain the observed significant (Ptension (PO2). O2 flux across the arterial wall was calculated by Fick's law. The percentage of O2 diffusing out of the RA were 0.6% at IOP of 10 mmHg, and 38% at IOP of 55 mmHg. Confirmation still requires measurement of blood velocity.

  15. Water diffusion in atmospherically relevant ?-pinene secondary organic material? ?Electronic supplementary information (ESI) available. See DOI: 10.1039/c5sc00685f Click here for additional data file.

    OpenAIRE

    Price, Hannah C.; Mattsson, Johan; Zhang, Yue; Allan K. Bertram; Davies, James F.; Grayson, James W.; Martin, Scot T.; O'Sullivan, Daniel; Reid, Jonathan P.; Rickards, Andrew M J; Murray, Benjamin J.

    2015-01-01

    Secondary organic material (SOM) constitutes a large mass fraction of atmospheric aerosol particles. Understanding its impact on climate and air quality relies on accurate models of interactions with water vapour. Recent research shows that SOM can be highly viscous and can even behave mechanically like a solid, leading to suggestions that particles exist out of equilibrium with water vapour in the atmosphere. In order to quantify any kinetic limitation we need to know water diffusion coeffic...

  16. Hg localisation in Tillandsia usneoides L. (Bromeliaceae), an atmospheric biomonitor

    Energy Technology Data Exchange (ETDEWEB)

    Filho, G.M.A. [Instituto de Pesquisas Jardim Botanico do Rio de Janeiro (Brazil). Programa Zona Costeira; Andrade, L.R.; Farina, M. [Cidade Universitaria, Rio de Janeiro (Brazil). Instituto de Ciencias Biomedicas, Departamento de Anatomia; Malm, O. [Cidade Universitaria, Rio de Janeiro (Brazil). Instituto de Biofisica Carlos Chagas Filho, Laboratorio de Radioisotopos Eduardo Penna Franca

    2002-07-01

    The Spanish moss, Tillandsia usneoides, has been applied as an atmospheric biomonitor of Hg contamination, although the mechanism of metal plant accumulation has not been understood until now. In the present work, analytical scanning electron microscopy (SEM) was used to localize Hg in T. usneoides exposed to a Hg-air-contaminated area during 15 days. After this period, Hg was determined by the flow injection mercury system, and plants were prepared for SEM observation and energy-dispersive X-ray analysis. A concentration of 2702{+-}318{mu}g Hgg{sup -1} was determined in exposed plants. The presented microanalytical results demonstrated that Hg was partly associated with atmospheric particles deposited upon the plant surface, but it was highly absorbed by the scales, stem and leaves surfaces and less absorbed by epidermal cells of T. usneoides. No Hg was detected in mesophyll parenchyma or in vascular system cells. The great surface adsorption area provided by the scales, in addition to the characteristics of T. usneoides morphology, especially of the node region, are suggested to confer the great capability of T. usneoides in Hg holding. (author)

  17. Growth and characterization of Hg(1-x)Cd(x)Se alloys

    Science.gov (United States)

    Andrews, R. N.; Szofran, F. R.; Lehoczky, S. L.

    1988-01-01

    A detailed evaluation of the influence of growth conditions on the radial and axial compositional variations in directionally solidified Hg(1-x)Cd(x)Se alloys was performed. The measured axial compositional profiles were fitted to theoretical profiles to determine the effective solute (CdSe) diffusion coefficient (D) for the Hg(1-x)Cd(x)Se system. The value for D was estimated to be 3.0 + or - 0.5 x 10 to the -5th sq cm/s and did not appear to be significantly affected by the rate of crystal growth. The axial crystal uniformity was shown to be highly growth-rate dependent, with the faster growth rates producing crystals of more uniform composition in the axial direction. The magnitude of the radial variations was also shown to be highly growth-rate dependent, with the slower growth rates producing crystals of greater radial uniformity. This translation rate dependence of the radial uniformity is discussed in terms of lateral solute diffusion and convective interfacial fluid flows.

  18. Stoichiometry, thickness and crystallinity of MOCVD grown Hg{sub 1x-y}Cd{sub x}Mn{sub y}Te determined by nuclear techniques of analysis

    Energy Technology Data Exchange (ETDEWEB)

    Studd, W.B.; Johnston, P.N.; Bubb, I.F. [Royal Melbourne Inst. of Tech., VIC (Australia); Leech, P.W. [Applied Research and Developement, Telecom Australia, Clayton, VIC (Australia)

    1993-12-31

    The quaternary semi-conductor Hg{sub 1-x-y}Cd{sub x}Mn{sub y}Te has been grown by Metal Organic Chemical Vapour Deposition using the Interdiffused Multi-layer Process. The layers have been analysed by Ion beam (PIXE, RBS, channeling) and related analytical techniques (EDXRF, XRD, RHEED) to obtain stoichiometric and structural information. The analysis shows that all four elements are present throughout the layer and that the elemental concentrations and thickness of the layer vary considerably over the film. Channeling, XRD and RHEED have been combined to show that the layer is polycrystalline. 14 refs., 3 figs.

  19. Simulation of the isotopic composition of stratospheric water vapour - Part 2: Investigation of HDO/H2O variations

    OpenAIRE

    Eichinger, Roland; Jöckel, Patrick; Lossow, Stefan

    2015-01-01

    Studying the isotopic composition of water vapour in the lower stratosphere can reveal the driving mechanisms of changes in the stratospheric water vapour budget and therefore help to explain the trends and variations of stratospheric water vapour during recent decades. We equipped a global chemistry climate model with a description of the water isotopologue HDO, comprising its physical and chemical fractionation effects throughout the hydrological cycle. We use this m...

  20. Simulation of the isotopic composition of stratospheric water vapour – Part 2: Investigation of HDO / H2O variations

    OpenAIRE

    R. Eichinger; Jöckel, P.; S. Lossow

    2015-01-01

    Studying the isotopic composition of water vapour in the lower stratosphere can reveal the driving mechanisms of changes in the stratospheric water vapour budget and therefore help to explain the trends and variations of stratospheric water vapour during recent decades. We equipped a global chemistry climate model with a description of the water isotopologue HDO, comprising its physical and chemical fractionation effects throughout the hydrological cycle. We use this mode...

  1. An investigation for the HgCdTe cleaning process

    Science.gov (United States)

    Lan, Tian-Yi; Wang, Nili; Zhao, Shuiping; Liu, Shi-Jia; Li, Xiang-Yang

    2014-11-01

    A new cleaning process for HgCdTe was designed - which used the improved SC-1,SC-2 and Br2- C2H5OH solutions as the main cleaning fluid and applied mega sound waves in the cleaning process. By analyzing the test results carried out on the HgCdTe surface, it was found that the material of HgCdTe for the application of new cleaning process was better than the one for the application of conventional cleaning process in the minority carrier lifetime, residual organic contamination, responsivity and specific detectivity.

  2. Diffuse scattering

    Energy Technology Data Exchange (ETDEWEB)

    Kostorz, G. [Eidgenoessische Technische Hochschule, Angewandte Physik, Zurich (Switzerland)

    1996-12-31

    While Bragg scattering is characteristic for the average structure of crystals, static local deviations from the average lattice lead to diffuse elastic scattering around and between Bragg peaks. This scattering thus contains information on the occupation of lattice sites by different atomic species and on static local displacements, even in a macroscopically homogeneous crystalline sample. The various diffuse scattering effects, including those around the incident beam (small-angle scattering), are introduced and illustrated by typical results obtained for some Ni alloys. (author) 7 figs., 41 refs.

  3. Tomographic retrieval of water vapour and temperature around polar mesospheric clouds using Odin-SMR

    Directory of Open Access Journals (Sweden)

    O. M. Christensen

    2014-11-01

    Full Text Available A special observation mode of the Odin satellite provides the first simultaneous measurements of water vapour, temperature and polar mesospheric cloud (PMC brightness over a large geographical area while still resolving both horizontal and vertical structures in the clouds and background atmosphere. The observation mode has been activated during June, July and August of 2010, 2011 and 2014, and for latitudes between 50 and 82° N. This paper focuses on the water vapour and temperature measurements carried out with Odin's sub-millimetre radiometer (SMR. The tomographic retrieval approach used provides water vapour and temperature between 75–90 km with a vertical resolution of about 2.5 km and a horizontal resolution of about 200 km. The precision of the measurements is estimated to 0.5 ppm for water vapour and 3 K for temperature. Due to limited information about the pressure at the measured altitudes, the results have large uncertainties (> 3 ppm in the retrieved water vapour. These errors, however, influence mainly the mean atmosphere retrieved for each orbit, and variations around this mean are still reliably captured by the measurements. SMR measurements are performed using two different mixer chains, denoted as frequency mode 19 and 13. Systematic differences between the two frontends have been noted. A first comparison with the Solar Occultation For Ice Experiment instrument (SOFIE on-board the Aeronomy of Ice in the Mesosphere (AIM satellite and the Fourier Transform Spectrometer of the Atmospheric Chemistry Experiment (ACE-FTS on-board SCISAT indicates that the measurements using the frequency mode 19 have a significant low bias in both temperature (> 20 K and water vapour (> 1 ppm, while the measurements using frequency mode 13 agree with the other instruments considering estimated errors. PMC brightness data are provided by the OSIRIS, Odin's other sensor. Combined SMR and OSIRIS data for some example orbits are considered. For these

  4. Sensitivity of polar stratospheric cloud formation to changes in water vapour and temperature

    Science.gov (United States)

    Khosrawi, F.; Urban, J.; Lossow, S.; Stiller, G.; Weigel, K.; Braesicke, P.; Pitts, M. C.; Rozanov, A.; Burrows, J. P.; Murtagh, D.

    2016-01-01

    More than a decade ago it was suggested that a cooling of stratospheric temperatures by 1 K or an increase of 1 ppmv of stratospheric water vapour could promote denitrification, the permanent removal of nitrogen species from the stratosphere by solid polar stratospheric cloud (PSC) particles. In fact, during the two Arctic winters 2009/10 and 2010/11 the strongest denitrification in the recent decade was observed. Sensitivity studies along air parcel trajectories are performed to test how a future stratospheric water vapour (H2O) increase of 1 ppmv or a temperature decrease of 1 K would affect PSC formation. We perform our study based on measurements made during the Arctic winter 2010/11. Air parcel trajectories were calculated 6 days backward in time based on PSCs detected by CALIPSO (Cloud Aerosol Lidar and Infrared Pathfinder satellite observations). The sensitivity study was performed on single trajectories as well as on a trajectory ensemble. The sensitivity study shows a clear prolongation of the potential for PSC formation and PSC existence when the temperature in the stratosphere is decreased by 1 K and water vapour is increased by 1 ppmv. Based on 15 years of satellite measurements (2000-2014) from UARS/HALOE, Envisat/MIPAS, Odin/SMR, Aura/MLS, Envisat/SCIAMACHY and SCISAT/ACE-FTS it is further investigated if there is a decrease in temperature and/or increase of water vapour (H2O) observed in the polar regions similar to that observed at midlatitudes and in the tropics. Performing linear regression analyses we derive from the Envisat/MIPAS (2002-2012) and Aura/MLS (2004-2014) observations predominantly positive changes in the potential temperature range 350 to 1000 K. The linear changes in water vapour derived from Envisat/MIPAS observations are largely insignificant, while those from Aura/MLS are mostly significant. For the temperature neither of the two instruments indicate any significant changes. Given the strong inter-annual variation observed in

  5. Systematic investigation of the signal properties of polycrystalline HgI{sub 2} detectors under mammographic, radiographic, fluoroscopic and radiotherapy irradiation conditions

    Energy Technology Data Exchange (ETDEWEB)

    Su Zhong; Antonuk, Larry E; El-Mohri, Youcef; Hu, Larry; Du Hong; Sawant, Amit; Li Yixin; Wang Yi; Yamamoto, Jin; Zhao Qihua [Department of Radiation Oncology, University of Michigan, 519 W. William St., Argus Building 1, Ann Arbor, MI 48103-4943 (United States)

    2005-06-21

    The signal properties of polycrystalline mercuric iodide (HgI{sub 2}) film detectors, under irradiation conditions relevant to mammographic, radiographic, fluoroscopic and radiotherapy x-ray imaging, are reported. Each film detector consists of an {approx}230 to {approx}460 {mu}m thick layer of HgI{sub 2} (fabricated through physical vapour deposition or a screen-print process) and a thin barrier layer, sandwiched between a pair of opposing electrode plates. The high atomic number, high density and low effective ionization energy, W{sub EFF}, of HgI{sub 2} make it an attractive candidate for significantly improving the performance of active matrix, flat-panel imagers (AMFPIs) for several x-ray imaging applications. The temporal behaviour of current from the film detectors in the presence and in the absence of radiation was used to examine dark current levels, the lag and reciprocity of the signal response, x-ray sensitivity and W{sub EFF}. The results are discussed in the context of present AMFPI performance. This study provides performance data for a wide range of potential medical x-ray imaging applications from a single set of detectors and represents the first investigation of the signal properties of polycrystalline mercuric iodide for the radiotherapy application.

  6. Warm water vapour in the sooty outflow from a luminous carbon star

    CERN Document Server

    Decin, L; Barlow, M J; Daniel, F; Cernicharo, J; Lombaert, R; De Beck, E; Royer, P; Vandenbussche, B; Wesson, R; Polehampton, E T; Blommaert, J A D L; De Meester, W; Exter, K; Feuchtgruber, H; Gear, W K; Gomez, H L; Groenewegen, M A T; Guelin, M; Hargrave, P C; Huygen, R; Imhof, P; Ivison, R J; Jean, C; Kahane, C; Kerschbaum, F; Leeks, S J; Lim, T; Matsuura, M; Olofsson, G; Posch, T; Regibo, S; Savini, G; Sibthorpe, B; Swinyard, B M; Yates, J A; Waelkens, C; 10.1038/nature09344

    2010-01-01

    In 2001, the discovery of circumstellar water vapour around the ageing carbon star IRC+10216 was announced. This detection challenged the current understanding of chemistry in old stars, since water vapour was predicted to be absent in carbon-rich stars. Several explanations for the occurrence of water vapour were postulated, including the vaporization of icy bodies (comets or dwarf planets) in orbit around the star, grain surface reactions, and photochemistry in the outer circumstellar envelope. However, the only water line detected so far from one carbon-rich evolved star can not discriminate, by itself, between the different mechanisms proposed. Here we report on the detection by the Herschel satellite of dozens of water vapour lines in the far-infrared and sub-millimetre spectrum of IRC+10216, including some high-excitation lines with energies corresponding to ~1000 K. The emission of these high-excitation water lines can only be explained if water vapour is present in the warm inner region of the envelop...

  7. Simulation of Discharge Production in a Water Vapour Layer on an Electrode

    Science.gov (United States)

    Karim, Mohammad; Evans, Benjamin; Asimakoulas, Leonidas; Stalder, Kenneth; Field, Thomas; Graham, Bill; Murakami, Tomoyuki

    2016-09-01

    Electrical discharges in water are receiving increasing attention because of chemical, environmental and biomedical applications.The work to be presented focuses on plasmas created directly in high conductivity water, saline solution. Here the plasma is produced at low voltage ( 200V) and is clearly associated with an initial vapour layer on the electrode surface that isolates the electrode from the liquid. In a previous paper a finite element multi-physics program, incorporating all relevant electrical and thermal properties of the solution was shown to reproduce the experimentally observed pre-plasma vapour layer behaviour. The results of a simulation of the plasma production in vapour layers of the same size and shape as predicted in will be presented, At present inert gas fills the ``vapour layer''. However this produces spatial distributions of the electron parameters that are consistent with the electric fields predicted in the original simulations. The water plasma simulation recently developed by Murakami is currently being included. It is anticipated that results of the coupled codes, showing the temporal and 2-D spatial development of the vapour and plasma, will be presented.

  8. Co-TPP functionalized carbon nanotube composites for detection of nitrobenzene and chlorobenzene vapours

    Indian Academy of Sciences (India)

    Swasti Saxena; G S S SAINI; A L Verma

    2015-04-01

    We report preparation of nanocomposites by non-covalent functionalization of carbon nanotubes (CNTs) with metal-tetraphenylporphyrins (M-TPP). Fourier transform infrared (FTIR) spectroscopy and transmission electron microscopy (TEM) results suggest formation of nanosized clusters of Co-TPP around the CNTs surface. X-ray diffraction studies indicate electronic charge re-distribution and strong interactions among CNTs and Co-TPP on functionalization. The films of the hybrid CNT–M-TPP nanocomposite exhibit change in conductivity on exposure to some chemical vapours. In the present work, the films prepared from the cobalt-TPP functionalized CNTs hybrid composites have been investigated for the detection of chlorobenzene (CB) and nitrobenzene (NB) vapours at room temperature. The films show response time of few seconds on exposure to both the NB and CB vapours while the recovery time for NB is significantly different compared to CB. A distinct and highly reproducible response pattern in the relative changes in resistance, recovery and response times on exposure to the vapours of NB, CB and few other chemicals at room temperature has been exploited to differentiate CB and NB vapours from one another.

  9. Retrieval of global water vapour columns from GOME-2 and first applications in polar regions

    Directory of Open Access Journals (Sweden)

    S. Noël

    2007-12-01

    Full Text Available Global total water vapour columns have been derived from measurements of the Global Ozone Monitoring Experiment 2 (GOME-2 on MetOp. For this purpose, the Air Mass Corrected Differential Optical Absorption Spectroscopy (AMC-DOAS method has been adapted, which has already been applied successfully to GOME (on ERS-2 and SCIAMACHY (SCanning Imaging Absorption spectroMeter for Atmospheric CHartographY, on ENVISAT data. Comparisons between the derived GOME-2 and SCIAMACHY water vapour columns show a good overall agreement. This gives confidence that the time series of water vapour columns from GOME-type instruments which started in 1995 can be continued by the MetOp instrumentation until at least 2020. The enhanced temporal and spatial resolution of GOME-2 enables the analysis of short-term variations particularly in the polar regions. This is especially important since atmospheric data sources in the polar regions are generally sparse. As an exemplary application, daily water vapour concentrations over the polar research station Ny Ålesund (78°55'19" N/11°56'33" E are investigated. At this latitude GOME-2 gives about six data points during daylight hours at varying local times. The results of this study show that it is possible to derive information about the diurnal variability of water vapour in polar regions from GOME-2 measurements.

  10. Passive remote sensing of the atmospheric water vapour content above land surfaces

    Science.gov (United States)

    Bartsch, B.; Bakan, S.; Fischer, J.

    The global distribution of the atmospheric water vapour content plays an important role in the weather forecast and climate research. Nowadays there exist various methods dealing with remote sensing of the atmospheric water vapour content. Unfortunately, most of them are restricted to ocean areas, since, in general, the emission of land surfaces is not known well enough. Therefore, a new method is developed which allows the detection of the atmospheric total water vapour content from aircraft or satellite with the aid of backscattered solar radiation in the near infrared above land surfaces. The Matrix-Operator-Method has been used to simulate backscattered solar radiances, including various atmospheric profiles of temperature, pressure, water vapour, and aerosols of various types, several sun zenith angles, and different types of land surfaces. From these calculations it can be concluded, that the detection of water vapour content in cloudless atmospheres is possible with an error of < 10 % even for higher aerosol contents. In addition to the theoretical results first comparisons with aircraft measurements of the backscattered solar radiances are shown. These measurements have been carried out with the aid of OVID (Optical Visible and near Infrared Detector), a new multichannel array spectrometer, in 1993.

  11. PRECIPITABLE WATER VAPOUR OVER LA SILLA PARANAL OBSERVATORY

    Directory of Open Access Journals (Sweden)

    F. Kerber

    2011-01-01

    Full Text Available En apoyo a la caracterización de sitios potenciales para el European Extremely Large Telescope (E-ELT, la ESO (European Southern Observatory, ISIS (Institute for Space Imaging Science y el grupo de Astrometeorología de la Universidad de Valparaío han establecido conjuntamente una mejor comprensión del PWV (precipitable water vapour sobre los Observatorio de ESO: La Silla y Paranal. Hasta ahora se han analizado estadísticamente 8 años válidos de espectros de alta resolución tomados con VLT-UVES para reconstruir la historia del PWV sobre Paranal. En el caso de La Silla se han usado 5 años de datos tomados con FEROS. En este análisis se utilizó un modelo de transferencia radiativa (BTRAM, desarrollado por ISIS. Tres campañas de medición fueron realizadas en mayo, agosto y noviembre de 2009 para entender mejor los errores sistemáticos presentes, y donde se validaron varios instrumentos y métodos con respecto a radiosondeos, que es la observación estándar en la investigación atmosférica. Después de corregirse los efectos sistemáticos, se encontró la mediana de PWV de 2.4 mm para Paranal mientras que el valor para La Silla es de 3.7 mm. Los resultados del estudio fueron presentados al Comité Asesor para la selección del sitio E-ELT en 2009. Se aprendieron lecciones valiosas para las operaciones del observatorio y ESO está planeando utilizar permanentemente un monitor de vapor de agua en Paranal como parte del proyecto para mejorar VISIR. Un monitor de PWV autónomo y de alta resolución será esencial para optimizar los resultados científicos de E-ELT.

  12. Cytotoxicity of dental composite (co)monomers and the amalgam component Hg{sup 2+} in human gingival fibroblasts

    Energy Technology Data Exchange (ETDEWEB)

    Reichl, Franz-Xaver; Simon, Sabine; Esters, Magalie; Seiss, Mario [Ludwig-Maximilians-University of Munich, Walther-Straub-Institute of Pharmacology and Toxicology, Munich (Germany); Kehe, Kai [Bundeswehr Institute of Pharmacology and Toxicology, Munich (Germany); Kleinsasser, Norbert [University of Regensburg, Department of Otolaryngology - Head and Neck Surgery, Regensburg (Germany); Hickel, Reinhard [Ludwig-Maximilians-University, Department of Operative Dentistry and Periodontology, Munich (Germany)

    2006-08-15

    Unpolymerized resin (co)monomers or mercury (Hg) can be released from restorative dental materials (e.g. composites and amalgam). They can diffuse into the tooth pulp or the gingiva. They can also reach the gingiva and organs by the circulating blood after the uptake from swallowed saliva. The cytotoxicity of dental composite components hydroxyethylmethacrylate (HEMA), triethyleneglycoldimethacrylate (TEGDMA), urethanedimethacrylate (UDMA), and bisglycidylmethacrylate (Bis-GMA) as well as the amalgam component Hg{sup 2+} (as HgCl{sub 2}) and methyl mercury chloride (MeHgCl) was investigated on human gingival fibroblasts (HGFs) at two time intervals. To test the cytotoxicity of substances, the bromodeoxyuridine (BrdU) assay and the lactate dehydrogenase (LDH) assay were used. The test substances were added in various concentrations and cells were incubated for 24 or 48 h. The EC{sub 50} values were obtained as half-maximum-effect concentrations from fitted curves. Following EC{sub 50} values were found [BrdU: mean (mmol/l); SEM in parentheses; n=12]: (24 h/48 h) HEMA 8.860 (0.440)/6.600(0.630), TEGDMA 1.810(0.130)/1.220(0.130), UDMA 0.120(0.010)/0.140(0.010), BisGMA 0.060(0.004)/0.040(0.002), HgCl{sub 2} 0.015(0.001)/0.050(0.006), and MeHgCl 0.004(0.001)/0.005(0.001). Following EC{sub 50} values were found [LDH: mean (mmol/l); SEM in parentheses; n=12]: (24 h/48 h) HEMA 9.490(0.300)/7.890(1.230), TEGDMA 2.300(0.470)/1.950(0.310), UDMA 0.200(0.007)/0.100(0.007), BisGMA 0.070(0.005)/0.100(0.002), and MeHgCl 0.014(0.006)/0.010(0.003). In both assays, the following range of increased toxicity was found for composite components (24 and 48 h): HEMA < TEGDMA < UDMA < BisGMA. In both assays, MeHgCl was the most toxic substance. In the BrdU assay, Hg{sup 2+} was about fourfold less toxic than MeHgCl but Hg{sup 2+} was about fourfold more toxic than BisGMA. In the BrdU test, a significantly (P<0.05) decreased toxicity was observed for Hg{sup 2+} at 48 h, compared to the 24 h

  13. Uptake of HgCl{sub 2} and MeHgCl in an insect cell line (Aedes albopictus C6/36)

    Energy Technology Data Exchange (ETDEWEB)

    Braeckman, B.; Cornelis, R.; Rzeznik, U.; Raes, H. [Univ. of Ghent (Belgium)

    1998-10-01

    The authors studied the uptake mechanism of mercuric chloride (Hg) and methylmercuric chloride (MeHg) in Aedes albopictus C6/36 cells. The uptake kinetics, together with the effect of temperature and a metabolic inhibitor (2,4-dinitrophenol) on the mercury accumulation, were examined. Both amounts of internalized Hg and MeHg increased linearly with the extracellular concentration. Initially, the influx rate was high for both metal species but MeHg was found to accumulate seven times faster than Hg. At longer exposure times it leveled off for Hg, while for MeHg, the intracellular concentration decreased. Hg toxicity was not significantly influenced by elevated temperatures; in contrast there was a marked decrease of the LC{sub 50/24 h} value for MeHg. On the other hand, Hg accumulation was temperature dependent but MeHg was not. The different toxicity and uptake rate of both mercury compounds can be explained in terms of membrane permeability and target site. For Hg the main target seems to be the plasma membrane, while MeHg readily crosses this barrier and reacts with intracellular targets. 2,4-Dinitrophenol had no effect on the accumulation of Hg but that of MeHg was doubled.

  14. Relativistic diffusion.

    Science.gov (United States)

    Haba, Z

    2009-02-01

    We discuss relativistic diffusion in proper time in the approach of Schay (Ph.D. thesis, Princeton University, Princeton, NJ, 1961) and Dudley [Ark. Mat. 6, 241 (1965)]. We derive (Langevin) stochastic differential equations in various coordinates. We show that in some coordinates the stochastic differential equations become linear. We obtain momentum probability distribution in an explicit form. We discuss a relativistic particle diffusing in an external electromagnetic field. We solve the Langevin equations in the case of parallel electric and magnetic fields. We derive a kinetic equation for the evolution of the probability distribution. We discuss drag terms leading to an equilibrium distribution. The relativistic analog of the Ornstein-Uhlenbeck process is not unique. We show that if the drag comes from a diffusion approximation to the master equation then its form is strongly restricted. The drag leading to the Tsallis equilibrium distribution satisfies this restriction whereas the one of the Jüttner distribution does not. We show that any function of the relativistic energy can be the equilibrium distribution for a particle in a static electric field. A preliminary study of the time evolution with friction is presented. It is shown that the problem is equivalent to quantum mechanics of a particle moving on a hyperboloid with a potential determined by the drag. A relation to diffusions appearing in heavy ion collisions is briefly discussed.

  15. Results Of Hg Speciation Testing On DWPF SMECT-1, SMECT-3, And SMECT-5 Samples

    Energy Technology Data Exchange (ETDEWEB)

    Bannochie, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2016-01-07

    The Savannah River National Laboratory (SRNL) was tasked with preparing and shipping samples for Hg speciation by Eurofins Frontier Global Sciences, Inc. in Seattle, WA on behalf of the Savannah River Remediation (SRR) Mercury Task Team. The thirteenth shipment of samples was designated to include Defense Waste Processing Facility (DWPF) Slurry Mix Evaporator Condensate Tank (SMECT) from Sludge Receipt and Adjustment Tank (SRAT) Batch 736 and 738 samples. Triplicate samples of each material were prepared for this shipment. Each replicate was analyzed for seven Hg species: total Hg, total soluble (dissolved) Hg, elemental Hg [Hg(0)], ionic (inorganic) Hg [Hg(I) and Hg(II)], methyl Hg [CH3Hg-X, where X is a counter anion], ethyl Hg [CH3CH2-Hg-X, where X is a counter anion], and dimethyl Hg [(CH3)2Hg]. The difference between the total Hg and total soluble Hg measurements gives the particulate Hg concentration, i.e. Hg adsorbed to the surface of particulate matter in the sample but without resolution of the specific adsorbed species. The average concentrations of Hg species in the aqueous samples derived from Eurofins reported data corrected for dilutions performed by SRNL are tabulated.

  16. Quantum Calorimeters Based on HgCdTe Alloys Project

    Data.gov (United States)

    National Aeronautics and Space Administration — NASA's next generation of x-ray observation missions require x-ray calorimeters with superior energy resolution. Semimetallic HgTe has already proven itself as an...

  17. Enrichment of Pb, Hg and Cr in cultured carp otolith

    African Journals Online (AJOL)

    AJL

    2012-01-26

    Jan 26, 2012 ... record the pollution condition at the sampling time. ... aquatic organisms are aquatic algae, zooplankton .... element cannot show that Hg concentration in otolith ..... from Atlantic croaker along an estuarine pollution gradient.

  18. Quantum Calorimeters Based on HgCdTe Alloys Project

    Data.gov (United States)

    National Aeronautics and Space Administration — NASA's next generation of x-ray observation missions require x-ray calorimeters with superior energy resolution. Semimetallic HgTe has already proven itself as an...

  19. Properties of Light Hg, Pb and Po Isotopes

    CERN Document Server

    Muntian, I

    2003-01-01

    Quality of mass description for three different theoretical mass models is studied. Masses and deformations for Po, Pb and Hg isotopes are compared with experimental data. Gap in the proton single particle energy spectrum is discussed.

  20. Horizontal Branch stars as AmFm/HgMn stars

    CERN Document Server

    Michaud, G

    2008-01-01

    Recent observations and models for horizontal branch stars are briefly described and compared to models for AmFm stars. The limitations of those models are emphasized by a comparison to observations and models for HgMn stars.

  1. Interaction of Hg Atom with Bare Si(111) Surface

    Institute of Scientific and Technical Information of China (English)

    LIU Yong-Jun; LIU Ying

    2006-01-01

    To evaluate the interaction between Hg atom and bare Si(111) surface, three types of silicon cluster models of Si4H7, Si7H10 and Si16H20 together with their Hg complexes were studied by using hybrid (U)B3LYP density functional theory method. Optimized geometries and energies for Hg atom on different adsorption sites indicate that: 1) the binding energies at different adsorption sites are small (ranging from ~3 to 8 kJ/mol dependent on the adsorption sites), suggesting a weak interaction between Hg atom and silicon surface; 2) the most favorable adsorption site is the on top (T) site. By analyzing their natural bonding orbitals, the possible reason of this difference is suggested.

  2. Cardiac dysfunction in HgCl2-induced nephrotic syndrome.

    Science.gov (United States)

    Moreira-Rodrigues, Mónica; Henriques-Coelho, Tiago; Moura, Cláudia; Vasques-Nóvoa, Francisco; Sampaio-Maia, Benedita; Pestana, Manuel; Leite-Moreira, Adelino F

    2010-03-01

    The experimental model of HgCl(2) injection is characterized by a systemic autoimmune disease which leads to the development of nephrotic syndrome (NS). NS seems to be accompanied by cardiovascular alterations, since patients with NS present an increased incidence in cardiac disease. The aim of our work was to study the effects of HgCl(2)-induced NS on myocardial function and morphometry. Normotensive Brown-Norway rats were injected with HgCl(2) (1 mg/kg, HgCl(2) group; n = 6, subcutaneous) or the vehicle (control group; n = 6, subcutaneous) on days 0, 2, 4, 7, 9 and 11. The animals were placed in metabolic cages for evaluation of urinary excretion of noradrenaline, sodium, total proteins, albumin and creatinine. Fourteen and 21 days after the first HgCl(2) injection, left ventricle (LV) hemodynamics was evaluated through pressure micromanometers in basal and isovolumetric heartbeats. The heart and gastrocnemius muscle weights and tibial length were also examined. In an additional group of animals cardiac dimensions and ejection fraction were assessed by echocardiography and LV apoptosis and fibrosis were studied. HgCl(2)-injected rats presented proteinuria, albuminuria, hyperlipidemia, anemia, sodium retention and ascites at day 14. These alterations were accompanied by LV hemodynamic changes only in isovolumetric heartbeats. Similarly, on day 21, HgCl(2)-injected rats presented proteinuria, albuminuria, hyperlipidemia, anemia, but no sodium retention or ascites. These animals presented LV systolic and diastolic dysfunction in both basal and isovolumetric heartbeats, as well as cardiac atrophy, LV fibrosis and an increase in myocyte apoptosis. In conclusion, HgCl(2)-induced NS is accompanied by LV dysfunction and can be a promising model for studying the link between NS and cardiac disease.

  3. Searching for Line Profile Variability in HgMn Stars

    CERN Document Server

    Turcotte, S; Knoglinger, P

    2002-01-01

    Spectra of four non-magnetic chemically peculiar late B type stars (HgMn) stars are analysed to detect periodic spectral line variations (LPVs). A procedure developed to study LPVs in Slowly Pulsating B stars has been adopted as pulsational properties of HgMn stars should be expected to be similar. In the preliminary results discussed here no conclusive evidence for periodic LPVs was uncovered. A more sensitive re-analysis of the data is under way.

  4. First observation of excited states in 173Hg93

    CERN Document Server

    O'Donnell, D; Scholey, C; Bianco, L; Capponi, L; Carroll, R J; Darby, I G; Donosa, L; Drummond, M; Ertugral, F; Greenlees, P T; Grahn, T; Hauschild, K; Herzan, A; Jakobsson, U; Jones, P; Joss, D T; Julin, R; Juutinen, S; Ketelhut, S; Labiche, M; Leino, M; Lopez-Martens, A; Mullholland, K; Nieminen, P; Peura, P; Rahkila, P; Rinta-Antila, S; Ruotsalainen, P; Sandzelius, M; Saren, J; Saygi, B; Simpson, J; Sorri, J; Thornthwaite, A; Uusitalo, J

    2012-01-01

    The neutron-deficient nucleus 173Hg has been studied following fusion-evaporation reactions. The observation of gamma rays decaying from excited states are reported for the first time and a tentative level scheme is proposed. The proposed level scheme is discussed within the context of the systematics of neighbouring neutron-deficient Hg nuclei. In addition to the gamma-ray spectroscopy, the alpha decay of this nucleus has been measured yielding superior precision to earlier measurements.

  5. Crystal structure of K[Hg(SCN)3] - a redetermination.

    Science.gov (United States)

    Weil, Matthias; Häusler, Thomas

    2014-09-01

    The crystal structure of the room-temperature modification of K[Hg(SCN)3], potassium tri-thio-cyanato-mercurate(II), was redetermined based on modern CCD data. In comparison with the previous report [Zhdanov & Sanadze (1952 ▶). Zh. Fiz. Khim. 26, 469-478], reliability factors, standard deviations of lattice parameters and atomic coordinates, as well as anisotropic displacement parameters, were revealed for all atoms. The higher precision and accuracy of the model is, for example, reflected by the Hg-S bond lengths of 2.3954 (11), 2.4481 (8) and 2.7653 (6) Å in comparison with values of 2.24, 2.43 and 2.77 Å. All atoms in the crystal structure are located on mirror planes. The Hg(2+) cation is surrounded by four S atoms in a seesaw shape [S-Hg-S angles range from 94.65 (2) to 154.06 (3)°]. The HgS4 polyhedra share a common S atom, building up chains extending parallel to [010]. All S atoms of the resulting (1) ∞[HgS2/1S2/2] chains are also part of SCN(-) anions that link these chains with the K(+) cations into a three-dimensional network. The K-N bond lengths of the distorted KN7 polyhedra lie between 2.926 (2) and 3.051 (3) Å.

  6. Self-powered sensor for trace Hg2+ detection.

    Science.gov (United States)

    Wen, Dan; Deng, Liu; Guo, Shaojun; Dong, Shaojun

    2011-05-15

    A self-powered electrochemical sensor has been facilely designed for sensitive detection of Hg(2+) based on the inhibition of biocatalysis process of enzymatic biofuel cell (BFC) for the first time. The as-prepared one-compartment BFC, which was consisted of alcohol dehydrogenase supported on single-walled carbon nanohorns-based mediator system as the anode and bilirubin oxidase as the cathodic biocatalyst, generated an open circuit potential (V(oc)) of 636 mV and a maximum power density of 137 μW cm(-2). It was interestingly found that the presence of Hg(2+) would affect the performance of the constructed BFC (e.g., V(oc)). Taking advantage of the inhibitive effect of Hg(2+), a novel self-powered Hg(2+) sensor has been developed, which showed a linear range of 1-500 nM (R(2) = 0.999) with a detection limit of 1 nM at room temperature. In addition, this BFC-type sensor exhibited good selectivity for Hg(2+) against other common environmental metal ions, and the feasibility of the method for Hg(2+) detection in actual water samples (i.e., tap, ground, and lake water) was demonstrated with satisfactory results.

  7. Simultaneous Removal of Hg(II and Phenol Using Functionalized Activated Carbon Derived from Areca Nut Waste

    Directory of Open Access Journals (Sweden)

    Lalhmunsiama

    2017-07-01

    Full Text Available Areca nut waste was utilized to obtain high surface area activated carbon (AC, and it was further functionalized with succinic anhydride under microwave irradiation. The surface morphology and surface functional groups of the materials were discussed with the help of scanning electron microscope(SEM images and fourier transform infra-red (FT-IR analysis. The specific surface area of the AC and functionalized-AC was obtained by the Brunauer-Emmett-Teller (BET method, and found to be 367.303 and 308.032 m2/g, respectively. Batch experiments showed that higher pH favoured the removal of Hg(II, whereas the phenol removal was slightly affected by the changes in the solution pH. The kinetic data followed pseudo-first order kinetic model, and intra-particle diffusion played a significant role in the removal of both pollutants. The maximum sorption capacity of Hg(II and phenol were evaluated using Langmuir adsorption isotherms, and found to be 11.23 and 5.37 mg/g, respectively. The removal of Hg(II was significantly suppressed in the presence of chloride ions due to the formation of a HgCl2 species. The phenol was specifically adsorbed, forming the donor–acceptor complexes or π–π electron interactions at the surface of the solid. Further, a fixed-bed column study was conducted for both Hg(II and phenol. The loading capacity of the column was estimated using the nonlinear Thomas equation, and found to be 2.49 and 2.70 mg/g, respectively. Therefore, the study showed that functionalized AC obtained from areca nut waste could be employed as a sustainable adsorbent for the simultaneous removal of Hg(II and phenol from polluted water.

  8. Prediction of clay content from water vapour sorption isotherms considering hysteresis and soil organic matter content

    DEFF Research Database (Denmark)

    Arthur, Emmanuel; Tuller, Markus; Moldrup, Per

    2015-01-01

    for estimating clay content from hygroscopic water at different relative humidity (RH) levels while considering hysteresis and organic matter content. Continuous adsorption/desorption vapour sorption isotherm loops were measured for 150 differently textured soils with a state-of-the-art vapour sorption analyser......Soil texture, in particular the clay fraction, governs numerous environmental, agricultural and engineering soil processes. Traditional measurement methods for clay content are laborious and impractical for large-scale soil surveys. Consequently, clay prediction models that are based on water...... vapour sorption, which can be measured within a shorter period of time, have recently been developed. Such models are often based on single-point measurements of water adsorption and do not account for sorption hysteresis or organic matter content. The present study introduces regression relationships...

  9. Kinetic model of water vapour adsorption by gluten-free starch

    Science.gov (United States)

    Ocieczek, Aneta; Kostek, Robert; Ruszkowska, Millena

    2015-01-01

    This study evaluated the kinetics of water vapour adsorption on the surface of starch molecules derived from wheat. The aim of the study was to determine an equation that would allow estimation of water content in tested material in any timepoint of the adsorption process aimed at settling a balance with the environment. An adsorption isotherm of water vapour on starch granules was drawn. The parameters of the Guggenheim, Anderson, and De Boer equation were determined by characterizing the tested product and adsorption process. The equation of kinetics of water vapour adsorption on the surface of starch was determined based on the Guggenheim, Anderson, and De Boer model describing the state of equilibrium and on the model of a first-order linear inert element describing the changes in water content over time.

  10. Distribution of tritium in water vapour and precipitation around Wolsung nuclear power plant.

    Science.gov (United States)

    Chae, Jung-Seok; Lee, Sang-Kuk; Kim, Yongjae; Lee, Jung-Min; Cho, Heung-Joon; Cho, Yong-Woo; Yun, Ju-Yong

    2011-07-01

    The distribution of tritium in water vapour and precipitation with discharge of tritiated water vapour and meteorological factors was studied around the Wolsung nuclear power plant (NPP) site during the period 2004-2008. The tritium concentrations in atmospheric water vapour and precipitation had a temporal variation with relatively high values in the early summer. Spatial distribution of tritium concentrations was affected by various factors such as distance from the NPP site, wind direction, tritium discharge into the atmosphere and atmospheric dispersion factor. The annual mean concentrations of atmospheric HTO and precipitation were correlated with the amount of gaseous tritium released from the Wolsung NPP. The tritium concentrations in precipitation decrease exponentially with an increase of the distance from the Wolsung NPP site.

  11. Low-pressure water vapour plasma treatment of surfaces for biomolecules decontamination

    Science.gov (United States)

    Fumagalli, F.; Kylián, O.; Amato, L.; Hanuš, J.; Rossi, F.

    2012-04-01

    Decontamination treatments of surfaces are performed on bacterial spores, albumin and brain homogenate used as models of biological contaminations in a low-pressure, inductively coupled plasma reactor operated with water-vapour-based gas mixtures. It is shown that removal of contamination can be achieved using pure H2O or Ar/H2O mixtures at low temperatures with removal rates comparable to oxygen-based mixtures. Particle fluxes (Ar+ ions, O and H atomic radicals and OH molecular radicals) from water vapour discharge are measured by optical emission spectroscopy and Langmuir probe under several operating conditions. Analysis of particle fluxes and removal rates measurements illustrates the role of ion bombardment associated with O radicals, governing the removal rates of organic matter. Auxiliary role of hydroxyl radicals is discussed on the basis of experimental data. The advantages of a water vapour plasma process are discussed for practical applications in medical devices decontamination.

  12. Isothermal (vapour + liquid) equilibrium of (cyclic ethers + chlorohexane) mixtures: Experimental results and SAFT modelling

    Energy Technology Data Exchange (ETDEWEB)

    Bandres, I.; Giner, B.; Lopez, M.C.; Artigas, H. [Departamento de Quimica Organica y Quimica Fisica, Facultad de Ciencias, Universidad de Zaragoza, Pedro Cerbuna 12, 50009 Zaragoza (Spain); Lafuente, C. [Departamento de Quimica Organica y Quimica Fisica, Facultad de Ciencias, Universidad de Zaragoza, Pedro Cerbuna 12, 50009 Zaragoza (Spain)], E-mail: celadi@unizar.es

    2008-08-15

    Experimental data for the isothermal (vapour + liquid) equilibrium of mixtures formed by several cyclic ethers (tetrahydrofuran, tetrahydropyran, 1,3-dioxolane, and 1,4-dioxane) and chlorohexane at temperatures of (298.15 and 328.15) K are presented. Experimental results have been discussed in terms of both, molecular characteristics of pure compounds and potential intermolecular interaction between them using thermodynamic information of the mixtures obtained earlier. Furthermore, the influence of the temperature on the (vapour + liquid) equilibrium of these mixtures has been explored and discussed. Transferable parameters of the SAFT-VR approach together with standard combining rules have been used to model the phase equilibrium of the mixtures and a description of the (vapour + liquid) equilibrium of them that is in excellent agreement with the experimental data are provided.

  13. Vapour-to-Liquid Nucleation in Associating Lennard-Jones Fluids with Multiple Association Sites

    Institute of Scientific and Technical Information of China (English)

    FU Dong; LIAO Tao

    2007-01-01

    The excess Helmholtz free energy functional for associating Lennard-Jones (LJ) fluid is formulated in terms of a weighted density approximation for short-ranged interactions and a Weeks Chandler-Andersen approximation for long-range attraction. Within the framework of density functional theory, phase equilibria, vapour-liquid surface tension and vapour-liquid nucleation properties including the density profile, work of formation, excess number of particles and critical supersaturation are investigated for associating LJ fluids with different numbers of association sites (M=1,2,3,4) per particle. The influences of association energy and association sites on phase equilibria, surface tension and vapour-liquid nucleation properties are discussed.

  14. Solid-state detector system for measuring concentrations of tritiated water vapour and other radioactive gases

    Science.gov (United States)

    Nunes, J. C.; Surette, R. A.; Wood, M. J.

    1999-08-01

    A detector system was built using a silicon photodiode plus preamplifier and a cesium iodide scintillator plus preamplifier that were commercially available. The potential of the system for measuring concentrations of tritiated water vapour in the presence of other radioactive sources was investigated. For purposes of radiation protection, the sensitivity of the detector system was considered too low for measuring tritiated water vapour concentrations in workplaces such as nuclear power plants. Nevertheless, the spectrometry capability of the system was used successfully to differentiate amongst some radioactive gases in laboratory tests. Although this relatively small system can measure radioactive noble gases as well as tritiated water vapour concentrations, its response to photons remains an issue.

  15. Multi-color IRFPAs made from HgCdTe grown by MOVPE

    Science.gov (United States)

    Jones, C. L.; Hipwood, L. G.; Price, J.; Shaw, C. J.; Abbott, P.; Maxey, C. D.; Lau, H. W.; Catchpole, R. A.; Ordish, M.; Knowles, P.; Gordon, N. T.

    2007-04-01

    The drive towards improved target recognition has led to an increasing interest in detection in more than one infrared band. This paper describes the design, fabrication and performance of two-colour and three-colour infrared detectors made from HgCdTe grown by Metal Organic Vapour Phase Epitaxy (MOVPE). The detectors are staring, focal plane arrays consisting of HgCdTe mesa-diode arrays bump bonded to silicon read-out integrated circuits (ROICs). Each mesa diode has one connection to the ROIC and the colours are selected by varying the applied bias. Results will be presented for both two-colour and three-colour devices. In a two-colour n-p-n design the cut-off wavelengths are defined by the compositions of the two n-type absorbers and the doping and composition of the p-type layer are chosen to prevent transistor action. The bias polarity is used to switch the output between colours. This design has been used to make MW/LW detectors with a MW band covering 3 to 5 μm and a LW band covering 5 to 10 μm. In a three-colour n-p-n design the cut-off wavelengths are defined by the compositions of the two n-type absorbers and the p-type absorber, which has an intermediate cut-off wavelength. The absorbers are separated from each other by electronic barriers consisting of wide band-gap material. At low applied bias these barriers prevent photo-electrons generated in the p-type absorber from escaping and the device then gives an output from one of the n-type absorbers. At high applied bias the electronic barrier is pulled down and the device gives an output from both the p-type absorber and one of the n-type absorbers. Thus by varying the polarity and magnitude of the bias it is possible to obtain three-colours from a two-terminal device. This design has been used to make a SW/MW/MW detector with cut-off wavelengths of approximately 3, 4 and 6 μm.

  16. Vapours of US and EU Market Leader Electronic Cigarette Brands and Liquids Are Cytotoxic for Human Vascular Endothelial Cells.

    Directory of Open Access Journals (Sweden)

    Raphaela Putzhammer

    Full Text Available The present study was conducted to provide toxicological data on e-cigarette vapours of different e-cigarette brands and liquids from systems viewed as leaders in the e-cigarette market and to compare e-cigarette vapour toxicity to the toxicity of conventional strong high-nicotine cigarette smoke. Using an adapted version of a previously constructed cigarette smoke constituent sampling device, we collected the hydrophilic fraction of e-cigarette vapour and exposed human umbilical vein endothelial cells (HUVECs to the mixture of compounds present in the vapour of 4 different single-use e-cigarettes, 6 different liquid vapours produced by the same refillable e-cigarette, and one e-cigarette with an exchangeable liquid cartridge. After incubation of cells with various concentrations and for various periods of time we analysed cell death induction, proliferation rates, the occurrence of intra-cellular reactive oxygen species, cell morphology, and we also measured e-cigarette heating coil temperatures. Overall, conventional cigarette smoke extract showed the most severe impact on endothelial cells. However, some e-cigarette vapour extracts showed high cytotoxicity, inhibition of cell proliferation, and alterations in cell morphology, which were comparable to conventional high-nicotine cigarettes. The vapours generated from different liquids using the same e-cigarette show substantial differences, pointing to the liquids as an important source for toxicity. E-cigarette vapour-mediated induction of oxidative stress was significant in one out of the 11 analysed vapours. There is a high variability in the acute cytotoxicity of e-cigarette vapours depending on the liquid and on the e-cigarettes used. Some products showed toxic effects close to a conventional high-nicotine cigarette. Liquid nicotine, menthol content, and the formation of acute intracellular reactive oxygen species do not seem to be the central elements in e-cigarette vapour toxicity.

  17. Intercomparison of atmospheric water vapour measurements at a Canadian High Arctic site

    Science.gov (United States)

    Weaver, Dan; Strong, Kimberly; Schneider, Matthias; Rowe, Penny M.; Sioris, Chris; Walker, Kaley A.; Mariani, Zen; Uttal, Taneil; McElroy, C. Thomas; Vömel, Holger; Spassiani, Alessio; Drummond, James R.

    2017-08-01

    Water vapour is a critical component of the Earth system. Techniques to acquire and improve measurements of atmospheric water vapour and its isotopes are under active development. This work presents a detailed intercomparison of water vapour total column measurements taken between 2006 and 2014 at a Canadian High Arctic research site (Eureka, Nunavut). Instruments include radiosondes, sun photometers, a microwave radiometer, and emission and solar absorption Fourier transform infrared (FTIR) spectrometers. Close agreement is observed between all combination of datasets, with mean differences ≤ 1.0 kg m-2 and correlation coefficients ≥ 0.98. The one exception in the observed high correlation is the comparison between the microwave radiometer and a radiosonde product, which had a correlation coefficient of 0.92.A variety of biases affecting Eureka instruments are revealed and discussed. A subset of Eureka radiosonde measurements was processed by the Global Climate Observing System (GCOS) Reference Upper Air Network (GRUAN) for this study. Comparisons reveal a small dry bias in the standard radiosonde measurement water vapour total columns of approximately 4 %. A recently produced solar absorption FTIR spectrometer dataset resulting from the MUSICA (MUlti-platform remote Sensing of Isotopologues for investigating the Cycle of Atmospheric water) retrieval technique is shown to offer accurate measurements of water vapour total columns (e.g. average agreement within -5.2 % of GRUAN and -6.5 % of a co-located emission FTIR spectrometer). However, comparisons show a small wet bias of approximately 6 % at the high-latitude Eureka site. In addition, a new dataset derived from Atmospheric Emitted Radiance Interferometer (AERI) measurements is shown to provide accurate water vapour measurements (e.g. average agreement was within 4 % of GRUAN), which usefully enables measurements to be taken during day and night (especially valuable during polar night).

  18. Persistent Hg contamination and occurrence of Hg-methylating transcript (hgcA) downstream of a chlor-alkali plant in the Olt River (Romania).

    Science.gov (United States)

    Bravo, Andrea G; Loizeau, Jean-Luc; Dranguet, Perrine; Makri, Stamatina; Björn, Erik; Ungureanu, Viorel Gh; Slaveykova, Vera I; Cosio, Claudia

    2016-06-01

    Chlor-alkali plants using mercury (Hg) cell technology are acute point sources of Hg pollution in the aquatic environment. While there have been recent efforts to reduce the use of Hg cells, some of the emitted Hg can be transformed to neurotoxic methylmercury (MeHg). Here, we aimed (i) to study the dispersion of Hg in four reservoirs located downstream of a chlor-alkali plant along the Olt River (Romania) and (ii) to track the activity of bacterial functional genes involved in Hg methylation. Total Hg (THg) concentrations in water and sediments decreased successively from the initial reservoir to downstream reservoirs. Suspended fine size particles and seston appeared to be responsible for the transport of THg into downstream reservoirs, while macrophytes reflected the local bioavailability of Hg. The concentration and proportion of MeHg were correlated with THg, but were not correlated with bacterial activity in sediments, while the abundance of hgcA transcript correlated with organic matter and Cl(-) concentration, indicating the importance of Hg bioavailability in sediments for Hg methylation. Our data clearly highlights the importance of considering Hg contamination as a legacy pollutant since there is a high risk of continued Hg accumulation in food webs long after Hg-cell phase out.

  19. The Influence of Cigarette Designs and Smoking Regimes on Vapour Phase Yields

    Directory of Open Access Journals (Sweden)

    Purkis W

    2014-12-01

    Full Text Available Cigarettes with similar design features but with either cellulose acetate or dual carbon filters were made at 1-mg and 13-mg “tar” levels, as determined under the ISO smoking procedure. Products were smoked under the ISO, Massachusetts and Canadian smoking regimes to provide per-cigarette and per-puff yields of twelve vapour phase (VP smoke components. The yields generated at the lit end of the cigarette and the significant yield reductions caused by filter ventilation, selective (carbon adsorption, tobacco rod ventilation and diffusion were estimated in a modelling approach. For a “1-mg tar” carbon-filtered product it was estimated that the VP generated at the lit end was reduced by 99.4% to a machine yield of 17 µg/cig under ISO smoking conditions. Under the Canadian regime with 100% vent blocking, the estimated total VP was lowered 20% by tobacco rod effects and 15% by carbon filter adsorption giving a machine yield of 3487 µg/cig. The carbon filter adsorbed less efficiently partly due to the artificially high smoke temperatures through the filter that would probably not be tolerated by human smokers. Under the Massachusetts regime with 50% vent blocking, conditions better associated with human smoking, the total VP was lowered 51% by filter ventilation, 22% by tobacco rod effects and 17% by carbon filter adsorption giving a machine yield of 659 µg/cig. Ventilation is used to achieve “tar”/nicotine/carbon monoxide yield ceilings at 10/1/10 mg based on the current ISO smoking method. If future regulations were to mandate further reductions in VP then this will only be selectively achieved by increasing filter or tobacco rod ventilation/porosity or by using selective adsorption. It is inevitable that manufacturers will need to add further ventilation into their product to comply with such regulations and this should be reflected in any smoking regime. Furthermore, regimes with 100% vent blocking, that do not produce data

  20. Effect of Liquid/Vapour Maldistribution on the Performance of Plate Heat Exchanger Evaporators

    DEFF Research Database (Denmark)

    Jensen, Jonas Kjær; Kærn, Martin Ryhl; Ommen, Torben Schmidt

    2015-01-01

    correlations for heat transfer and pressure drop. The flow distribution on both the refrigerant and secondary side is determined based on equal pressure drop while the liquid/vapour distribution is imposed to the model. Results show that maldistribution may cause up to a 25 % reduction of the overall heat...... transfer coefficient, compared to a lumped model with uniform distribution.......Plate heat exchangers are often applied as evaporators in industrial refrigeration and heat pump systems. In the design and modelling of such heat exchangers the flow and liquid/vapour distribution is often assumed to be ideal. However, maldistribution may occur and will cause each channel...

  1. Applicability of chemical vapour polishing of additive manufactured parts to meet production-quality

    DEFF Research Database (Denmark)

    Pedersen, D. B.; Hansen, H. N.; Nielsen, J. S.

    2014-01-01

    The Fused Deposition Modelling (FDM) method is the most rapidly growing Additive Manufacturing (AM) method[1]. FDM employs a 2.5D deposition scheme which induce a step-ladder shaped surface definition [2], with seams of the individual layers clearly visible[3]. This paper investigate to which...... extend chemical vapour polishing can be applied to eliminate the layered surfaces from FDM, so that a polished surface quality is obtained. It is quantified to what extend parts can be vapour polished and how geometrical and mechanical properties alter. The fundamental question is whether the surfaces...

  2. Experimental Investigation of Influence of Acoustic Wave on Vapour Precipitation Process

    Directory of Open Access Journals (Sweden)

    V. Vekteris

    2013-02-01

    Full Text Available The measurement results of acoustic field parameters above electroplating bath, in presence of water vapour, are analyzed in this work. Suction was created by means of side exhausters. It is obtained that the sound field generator generated a sound level of 130–140 dB at frequency interval between 1 and 10 kHz. It is shown that aerosol coagulation and precipitation processes are intensified under the mentioned conditions. The concentration of vapour and other aerosols in removal air decreases as a result, therefore air cleaning equipment costs can be reduced and cleaning efficiency increased.

  3. Application of off-gas treatment technology to soil vapour extraction systems

    Energy Technology Data Exchange (ETDEWEB)

    Karp, G. S.; Harvey, E. M.; McKee, R. C. E. [O`Connor Associates Environmental Inc., Oakville, ON (Canada); Lucas, W. P. [Commenco Systems Inc., Concord, ON (Canada)

    1995-12-31

    Various off-gas treatment technologies, including carbon adsorption, thermal incineration, UV oxidation, bio-reactors, combustion and catalytic oxidation were investigated as means to remediate sub-surface soils contaminated with petroleum hydrocarbons or volatile organic compounds. The primary objective was to determine the most cost-effective portable off-gas treatment technology for a typical soil vapour extraction system. Advantages, disadvantages and relative costs of each technology were summarized. Catalytic oxidation was found to be the most cost-effective method for off-gas treatment for the specified soil vapour extraction systems.

  4. Vapour pressure and enthalpy of aqueous lithium bromide solutions. [Used in absorption heat pumps

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, A.; Patwardhan, V.S. (National Chemical Lab., Poona (India))

    1992-07-01

    In this paper we present new equations for accurate calculations of the vapour pressure and enthalpy of aqueous lithium bromide solutions which are commonly used in absorption heat pumps and absorption heat transformers. The number of empirical parameters involved in these equations is much smaller than those in earlier equations. Moreover, the present equations for both vapour pressure and enthalpy involve the same constants as both these equations are derived from a single free energy equation using standard thermodynamic concepts. The present methodology can be used with any other electrolyte for which enthalpy-concentration diagrams may not be readily available. (Author).

  5. Low pressure water vapour plasma treatment of surfaces for biomolecules decontamination

    DEFF Research Database (Denmark)

    Fumagalli, F; Kylian, O; Amato, Letizia

    2012-01-01

    be achieved using pure H2O or Ar/H2O mixtures at low temperatures with removal rates comparable to oxygen-based mixtures. Particle fluxes (Ar+ ions, O and H atomic radicals and OH molecular radicals) from water vapour discharge are measured by optical emission spectroscopy and Langmuir probe under several......Decontamination treatments of surfaces are performed on bacterial spores, albumin and brain homogenate used as models of biological contaminations in a low-pressure, inductively coupled plasma reactor operated with water-vapour-based gas mixtures. It is shown that removal of contamination can...

  6. Fabrication of liquid crystal based sensor for detection of hydrazine vapours

    Science.gov (United States)

    Nandi, Rajib; Singh, Sachin Kumar; Singh, Hemant Kumar; Singh, Bachcha; Singh, Ranjan K.

    2014-10-01

    A novel liquid crystal (LC) based sensor to detect trace level amount of hydrazine vapour has been developed. The LC 4‧-pentyl-4-biphenylcarbonitrile (5CB) doped with 0.5 wt% 4-decyloxy benzaldehyde (DBA) shows dark to bright optical texture upon exposure of hydrazine vapours as revealed by polarizing optical microscopy under crossed polarizers. The hydrazine interacts with the doped DBA and form diimine compound which disrupt the orientation of aligned 5CB. The interaction between DBA and hydrazine has been also studied by Raman spectroscopy.

  7. Hg $L_{3}$ edge absorption study of the $HgBa_{2}CuO_{4}\\delta$ superconductor

    CERN Document Server

    Ziyu, Wu; Bianconi, A

    2001-01-01

    The HgBa/sub 2/CuO/sub 4+ delta / superconductor has been studied by high resolution Hg L/sub 3/ X-ray absorption near-edge structure (XANES) spectroscopy. The XANES spectrum has been simulated by full multiple-scattering calculations in order to explore the origin of different features in the experimental spectrum. The experimental Hg L/sub 3/-edge spectrum could be well reproduced by considering a cluster of 85 atoms, containing 10 shells, within a radius of about 7 AA from the central Hg atom. The low energy spectral feature in the XANES spectrum is found to be due to a transition from the Hg p states to the electronic states hybridized with higher shell Ba atoms. This implies that the transition features in the Hg L/sub 3/- edge XANES are strongly influenced by medium range order effects unlike the case of L/sub 3/ edge of 3d transition metals where short- range order is enough to describe the main transition features. (25 refs).

  8. Hg SOIL GAS AND Hg SOIL DISTRIBUTION AROUND FORMER „ZRINSKI“ MINE ON MT. MEDVEDNICA, CROATIA

    Directory of Open Access Journals (Sweden)

    Nataša Jug

    2008-12-01

    Full Text Available The purpose of this study is to present the field and laboratory researches, statistical analyses and graphical displays of the results of Hg soil gas and Hg soil distribution in the area around former mining site „Zrinski“ on Mt. Medvednica. The values of overall Hg concentrations in the soil gas show lognormal distribution, and their spatial distribution outlines the connection with the present Pb-Ag-Zn mineralization and confirms anthropogenic origin of uneven landscape relief (waste rock clusters. Regression analysis of the dependence between Hg contents in the soil gas and the distance from the mine entrance (correlation coefficient r also points to the considerable spatial dependence. Hg soil contents show as well distribution similar to lognormal, and there is a slight correlation when compared with Hg soil gas content. Concentrations are mostly within background values, except in the immediate vicinity of the mine entrance where the values are significantly higher due to the mineralization influence concentrated in the waste-rock clusters. Soil pollution caused by mercury is of local character with the spreading tendency to the south-west because of the dominant relief influence. Mercury found in the soil of the research location derives from the present mineral body and former mining activities, while possible anthropogenic atmospheric inputs from remote sources can not be proven on the basic of conducted research studies (the paper is published in Croatian.

  9. Anti-yeast activity of mentha oil and vapours through in vitro and in vivo (real fruit juices) assays.

    Science.gov (United States)

    Tyagi, Amit Kumar; Gottardi, Davide; Malik, Anushree; Guerzoni, Maria Elisabetta

    2013-04-15

    The anti-yeast activity of mentha oil and vapours was evaluated against 8 food spoiling yeasts through disc diffusion, disc volatilisation and micro broth dilution method. The minimum inhibitory concentration (MIC) and minimum fungicidal concentration (MFC) varied from 0.28 to 2.25 and 1.13 to 4.5 mg/ml, respectively. Furthermore, the anti-yeast efficacy of mentha oil alone and in combination with thermal treatment was evaluated in a real food system i.e. mixed fruit juices. The samples treated with a combination of mentha oil at the MIC, ½ MIC and ¼ MIC levels and thermal treatment enhanced the reduction viability. Chemical characterisation of mentha oil by gas chromatography-mass spectrometry (GC-MS) revealed that the dominant compounds were cis-menthone (27.43%), menthol (24.3%), trans-menthone (9.23%), limonene (5.84%), menthofuran (4.44%) and isomenthol (3.21%). Present results established the superior performance of integrated treatment over individual exposure for fruit juice preservation.

  10. Metal-organic chemical vapour deposition of lithium manganese oxide thin films via single solid source precursor

    Directory of Open Access Journals (Sweden)

    Oyedotun K.O.

    2015-12-01

    Full Text Available Lithium manganese oxide thin films were deposited on sodalime glass substrates by metal organic chemical vapour deposition (MOCVD technique. The films were prepared by pyrolysis of lithium manganese acetylacetonate precursor at a temperature of 420 °C with a flow rate of 2.5 dm3/min for two-hour deposition period. Rutherford backscattering spectroscopy (RBS, UV-Vis spectrophotometry, X-ray diffraction (XRD spectroscopy, atomic force microscopy (AFM and van der Pauw four point probe method were used for characterizations of the film samples. RBS studies of the films revealed fair thickness of 1112.311 (1015 atoms/cm2 and effective stoichiometric relationship of Li0.47Mn0.27O0.26. The films exhibited relatively high transmission (50 % T in the visible and NIR range, with the bandgap energy of 2.55 eV. Broad and diffused X-ray diffraction patterns obtained showed that the film was amorphous in nature, while microstructural studies indicated dense and uniformly distributed layer across the substrate. Resistivity value of 4.9 Ω·cm was obtained for the thin film. Compared with Mn0.2O0.8 thin film, a significant lattice absorption edge shift was observed in the Li0.47Mn0.27O0.26 film.

  11. Superconducting Hg-Based Mixed Oxides and Oxyfluorides

    Science.gov (United States)

    Antipov, E. V.

    2000-09-01

    Syntheses under high pressure and under controlled mercury and oxygen partial pressures of different members of the HgBa2Can-1CunO2n+2+δ series have been developed. There are two main parameters influencing Tc in this family: width of a perovskite slab (n) and concentration (δ) of the extra oxygen located in the Hg layer. The increase of Tc with n occurs until the third member, while after that it decreases. All the members of the series exhibit similar cupola shaped dependencies of Tc vs. δ. Strongly overdoped high members of the series with n = 3-5 were prepared only using high pressure technique and BaO2 as an internal oxidizer. Neutron powder diffraction experiments were carried out for monophase oxygenated HgBa2CuO4F4+δ and fluorinated HgBa2CuO4Fδ samples with different extra oxygen or fluorine content and Tc values. Fluorinated series also exhibits the cupola -like behavior for the Tc vs. δ dependence. NPD showed twice the amount of extra fluorine in comparison with those for the oxygenated Hg-1201 phases with close Tc's. The exchange of the extra oxygen by double amount of fluorine causes shortening of the apical Cu-O distances, while the in-plane ones, as well as Tc, do not vary. The influence of the external pressure on the structure and Tc of Hg-1201 strongly depends on the doping level. The increase of the extra oxygen content on going from underdoped to overdoped state results in the larger compression of the apical Cu-O and Ba-OHg distances while the HgO2 dumbbell as well as the distance between Ba and O from the (CuO2) layers becomes practically pressure independent. These results together with the data for fluorinated materials allow to elucidate the crucial structural features responsible for the Tc variation under high pressure.

  12. Temperature dependence of the oxide growth on aluminized 9-12%Cr ferritic-martensitic steels exposed to water vapour oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Sanchez, L., E-mail: lsanche@quim.ucm.e [Universidad Complutense de Madrid. Grupo de Investigacion de Ingenieria de Superficies y Materiales Nanoestructurados. Avenida Complutense s/n, Facultad de Ciencias Quimicas, 28040 Madrid (Spain); Bolivar, F.J. [Universidad de Antioquia. Facultad de Ingenierias. Medellin (Colombia); Hierro, M.P.; Perez, F.J. [Universidad Complutense de Madrid. Grupo de Investigacion de Ingenieria de Superficies y Materiales Nanoestructurados. Avenida Complutense s/n, Facultad de Ciencias Quimicas, 28040 Madrid (Spain)

    2009-04-02

    High temperature steam oxidation resistance of aluminide coatings obtained on 9-12% Cr ferritic-martensitic steels, which have been developed by chemical vapour deposition in fluidized bed reactor (CVD-FBR) using a bed modified with Zr particles, is presented here. The resulting coatings composed of (Fe,Cr){sub 2}Al{sub 5} intermetallic phase provide a high temperature steam oxidation resistance, which depends on the oxidation temperature. At 650 {sup o}C, after 1000 h of exposure, the alumina formed on the surface acts as a protective barrier. However, when the oxidation temperature increases up to 800 {sup o}C, the alumina scale fails before 1000 h of exposure giving rise to the formation of the Cr{sub 2}O{sub 3} and (Fe,Mn){sub 3}O{sub 4}, due to the high atomic diffusion rate at this temperature.

  13. Leidenfrost vapour layer moderation of the drag crisis and trajectories of superhydrophobic and hydrophilic spheres falling in water

    KAUST Repository

    Vakarelski, Ivan Uriev

    2014-01-01

    We investigate the dynamic effects of a Leidenfrost vapour layer sustained on the surface of heated steel spheres during free fall in water. We find that a stable vapour layer sustained on the textured superhydrophobic surface of spheres falling through 95 °C water can reduce the hydrodynamic drag by up to 75% and stabilize the sphere trajectory for the Reynolds number between 104 and 106, spanning the drag crisis in the absence of the vapour layer. For hydrophilic spheres under the same conditions, the transition to drag reduction and trajectory stability occurs abruptly at a temperature different from the static Leidenfrost point. The observed drag reduction effects are attributed to the disruption of the viscous boundary layer by the vapour layer whose thickness depends on the water temperature. Both the drag reduction and the trajectory stabilization effects are expected to have significant implications for development of sustainable vapour layer based technologies. © the Partner Organisations 2014.

  14. Carbon dioxide and water vapour characteristics on the west coast of Arabian Sea during Indian summer monsoon

    Indian Academy of Sciences (India)

    T Dharmaraj; M N Patil; R T Waghmare; P Ernest Raj

    2012-08-01

    Carbon dioxide, water vapour, air temperature and wind measurements at 10 Hz sampling rate were carried out over the coast of Arabian Sea, Goa (15°21′N, 73° 51′E) in India. These observations were collected, in association with the surface layer turbulent parameters for the Arabian Sea Monsoon Experiment (ARMEX). In the summer monsoon period, concentration of CO2 was in the range of 550–790 mg m−3 whereas the water vapour was in the range of 17.5–24.5 g m−3. The Fast Fourier Transform (FFT) analysis has been performed on these observations to investigate the spectral behaviour of CO2 and water vapour. The relation between CO2 and water vapour on various atmospheric scales has been proposed. CO2 and water vapour observations confirmed the existence of periodicities of large (11, 8 days), meso (5 days) and micrometeorological (20 min) scales.

  15. A review on the recent development of solar absorption and vapour compression based hybrid air conditioning with low temperature storage

    Directory of Open Access Journals (Sweden)

    Noor D. N.

    2016-01-01

    Full Text Available Conventional air conditioners or vapour compression systems are main contributors to energy consumption in modern buildings. There are common environmental issues emanating from vapour compression system such as greenhouse gas emission and heat wastage. These problems can be reduced by adaptation of solar energy components to vapour compression system. However, intermittence input of daily solar radiation was the main issue of solar energy system. This paper presents the recent studies on hybrid air conditioning system. In addition, the basic vapour compression system and components involved in the solar air conditioning system are discussed. Introduction of low temperature storage can be an interactive solution and improved economically which portray different modes of operating strategies. Yet, very few studies have examined on optimal operating strategies of the hybrid system. Finally, the findings of this review will help suggest optimization of solar absorption and vapour compression based hybrid air conditioning system for future work while considering both economic and environmental factors.

  16. Mercury (Hg) burden in children: The impact of dental amalgam

    Energy Technology Data Exchange (ETDEWEB)

    Al-Saleh, Iman, E-mail: iman@kfshrc.edu.sa [Biological and Medical Research Department, King Faisal Specialist Hospital and Research Centre, PO Box: 3354, Riyadh 11211 (Saudi Arabia); Al-Sedairi, Al anoud [Department of Zoology, College of Science, King Saud University, PO Box: 24452, Riyadh 11495 (Saudi Arabia)

    2011-07-15

    The risks and benefits of using mercury (Hg) in dental amalgam have long been debated. This study was designed to estimate Hg body burden and its association with dental amalgam fillings in 182 children (ages: 5-15 years) living in Taif City. Hg was measured in urine (UHg), hair (HHg) and toenails (NHg) by the Atomic Absorption Spectrophotometer with Vapor Generator Accessory system. Urinary Hg levels were calculated as both micrograms per gram creatinine ({mu}g/g creatinine) and micrograms per liter ({mu}g/L). We found that children with amalgam fillings (N = 106) had significantly higher UHg-C levels than children without (N = 76), with means of 3.763 {mu}g/g creatinine versus 3.457 {mu}g/g creatinine, respectively (P = 0.019). The results were similar for UHg (P = 0.01). A similar pattern was also seen for HHg, with means of 0.614 {mu}g/g (N = 97) for children with amalgam versus 0.242 {mu}g/g (N = 74) for those without amalgam fillings (P = 0). Although the mean NHg was higher in children without amalgam (0.222 {mu}g/g, N = 61) versus those with (0.163 {mu}g/g, N = 101), the relationship was not significant (P = 0.069). After adjusting for many confounders, the multiple logistic regression model revealed that the levels of UHg-C and HHg were 2.047 and 5.396 times higher, respectively, in children with dental amalgam compared to those without (P < 0.01). In contrast, a significant inverse relationship was seen between NHg levels and dental amalgam fillings (P = 0.003). Despite the controversy surrounding the health impact of dental amalgam, this study showed some evidence that amalgam-associated Hg exposure might be related with symptoms of oral health, such as aphthous ulcer, white patches, and a burning-mouth sensation. Further studies are needed to reproduce these findings. The present study showed that significant numbers of children with or without amalgam had Hg levels exceeding the acceptable reference limits. The detrimental neurobehavioral and

  17. Overcoming phytoremediation limitations. A case study of Hg contaminated soil

    Science.gov (United States)

    Barbafieri, Meri

    2013-04-01

    Phytoremediation is a broad term that comprises several technologies to clean up water and soil. Despite the numerous articles appearing in scientific journals, very few field applications of phytoextraction have been successfully realized. The research here reported on Phytoextraction, the use the plant to "extract" metals from contaminated soil, is focused on implementations to overcome two main drawbacks: the survival of plants in unfavorable environmental conditions (contaminant toxicity, low fertility, etc.) and the often lengthy time it takes to reduce contaminants to the requested level. Moreover, to overcome the imbalance between the technology's potential and its drawbacks, there is growing interest in the use of plants to reduce only the fraction that is the most hazardous to the environment and human health, that is to target the bioavailable fractions of metals in soil. Bioavailable Contaminant Stripping (BCS) would be a remediation approach focused to remove the bioavailable metal fractions. BCS have been used in a mercury contaminated soil from Italian industrial site. Bioavailable fractions were determined by sequential extraction with H2O and NH4Cl.Combined treatments of plant hormone and thioligand to strength Hg uptake by crop plants (Brassica juncea and Helianthus annuus) were tested. Plant biomass, evapotranspiration, Hg uptake and distribution following treatments were compared. Results indicate the plant hormone, cytokinine (CK) foliar treatment, increased evapotranspiration rate in both tested plants. The Hg uptake and translocation in both tested plants increased with simultaneous addition of CK and TS treatments. B. juncea was the most effective in Hg uptake. Application of CK to plants grown in TS-treated soil lead to an increase in Hg concentration of 232% in shoots and 39% in roots with respect to control. While H. annuus gave a better response in plant biomass production, the application of CK to plants grown in TS-treated soil lead to

  18. Spectroscopic variability and magnetic fields of HgMn stars

    CERN Document Server

    Hubrig, S; Ilyin, I; Korhonen, H; Savanov, I S; Dall, T; Schoeller, M; Cowley, C R; Briquet, M; Arlt, R

    2011-01-01

    The discovery of exotic abundances, chemical inhomogeneities, and weak magnetic fields on the surface of late B-type primaries in spectroscopic binaries has important implications not only for our understanding of the formation mechanisms of stars with Hg and Mn peculiarities themselves, but also for the general understanding of B-type star formation in binary systems. The origin of the abundance anomalies observed in late B-type stars with HgMn peculiarity is still poorly understood. The connection between HgMn peculiarity and membership in binary and multiple systems is supported by our observations during the last decade. The important result achieved in our studies of a large sample of HgMn stars is the finding that most HgMn stars exhibit spectral variability of various chemical elements, proving that the presence of an inhomogeneous distribution on the surface of these stars is a rather common characteristic and not a rare phenomenon. Further, in the studied systems, we found that all components are che...

  19. Bioaccumulation of Hg in the mushroom Pleurotus ostreatus

    Energy Technology Data Exchange (ETDEWEB)

    Bressa, G.; Cima, L.; Costa, P.

    1988-10-01

    The possibility of utilizing industrial, urban, and other wastes for the growth of a product which is directly edible by humans is fascinating. However, it is possible that many wastes containing toxic substances, for example, heavy metals, could reach the food chain and produce adverse effects on human health. To this end, we studied the possibility of bioaccumulation of Hg by a mushroom, Pleurotus ostreatus, grown on an artificial compost containing this element. Concentrations of 0.05, 0.1, and 0.2 mg/kg of Hg as Hg(NO/sub 3/)/sub 2/.H/sub 2/O were added to three groups of the same compost, successively inoculated with the mycelia of the mushroom. Higher concentrations strongly reduced the growth of the mycelia and therefore were not utilized. The concentrations of Hg in the substrate and in the mushroom were evaluated by AAS. The range of the accumulation factor was found to be 65-140, i.e., very marked. This finding suggests that the cultivation of P. ostreatus on substrates containing Hg from industrial and urban wastes could involve possible risks to human health.

  20. Are there tangled magnetic fields on HgMn stars?

    CERN Document Server

    Kochukhov, O; Piskunov, N; Jeffers, S V; Johns-Krull, C M; Keller, C U; Rodenhuis, M; Snik, F; Stempels, H C; Valenti, J A

    2013-01-01

    Several recent spectrophotometric studies failed to detect significant global magnetic fields in late-B HgMn chemically peculiar stars, but some investigations have suggested the presence of strong unstructured or tangled fields in these objects. We used detailed spectrum synthesis analysis to search for evidence of tangled magnetic fields in high-quality observed spectra of 8 slowly rotating HgMn stars and one normal late-B star. We also evaluated recent sporadic detections of weak longitudinal magnetic fields in HgMn stars based on the moment technique. Our analysis of the Zeeman broadening of magnetically sensitive spectral lines reveals no evidence of tangled magnetic fields in any of the studied HgMn or normal stars. We infer upper limits of 200-700 G for the mean magnetic field modulus -- much smaller than the field strengths implied by studies based on differential magnetic line intensification and quadratic field diagnostics. The new HARPSpol longitudinal field measurements for the extreme HgMn star H...

  1. Sustained low diffusing capacity in hepatopulmonary syndrome after liver transplantation

    Institute of Scientific and Technical Information of China (English)

    Graciela Martínez-Pallí; Federico P Gómez; Joan A Barberà; Miquel Navasa; Josep Roca; Robert Rodríguez-Roisin; Felip Burgo; Conchi Gistau

    2006-01-01

    AIM: To study the presence of sustained low diffusing capacity (DLco) after liver transplantation (LT) in patients with hepatopulmonary syndrome (HPS).METHODS: Six patients with mild-to-severe HPS and 24 without HPS who underwent LT were prospectively followed before and after LT at mid-term (median,15 mo). HPS patients were also assessed at long-tem (median, 86 mo).RESULTS: Before LT, HPS patients showed lower PaO2 (71 ± 8 mmHg), higher AaPO2 (43 ± 10 mmHg) and lower DLCO (54% ± 9% predicted), due to a combination of moderate-to-severe ventilation-perfusion (VA/Q)imbalance, mild shunt and diffusion limitation, than nonHPS patients (94 ± 4 mmHg and 19 ± 3 mmHg, and 85% ± 3% predicted, respectively) (P < 0.05 each).Seven non-HPS patients had also reduced DLCO (70% ±4% predicted).At mid- and long-term after LT, compared to preLT, HPS patients normalized PaO2 (91 ± 3 mmHg and 87 ± 5 mmHg), AaPO2 (14 ± 3 mmHg and 23 ± 5mmHg) and all VA/Q descriptors (P < 0.05 each) without changes in DLCO (53% ± 8% and 56% ± 7% predicted,respectively). Post-LT DLCO in non-HPS patients with preLT low DLCO was unchanged (75% ± 6% predicted).CONCLUSION: While complete VA/Q resolution in HPS indicates a reversible functional disturbance, sustained low DLCO after LT also present in some non-HPS patients,points to persistence of sub-clinical liver-induced pulmonary vascular changes.

  2. Solvents for CO2 capture. Structure-activity relationships combined with vapour-liquid-equilibrium measurements

    NARCIS (Netherlands)

    Mergler, Y.L.; Rumley-Van Gurp, R.; Brasser, P.; Koning, M.C. de; Goetheer, E.L.V.

    2011-01-01

    In this study a systematic approach was chosen to test and characterize amine systems for CO2 capture. Vapour-liquid-equilibrium measurements were performed on a homologue series of amines, with ethylene amine as base structure. Various functional groups were used that ranged in chemical and

  3. Using Peltier Cells to Study Solid-Liquid-Vapour Transitions and Supercooling

    Science.gov (United States)

    Torzo, Giacomo; Soletta, Isabella; Branca, Mario

    2007-01-01

    We propose an apparatus for teaching experimental thermodynamics in undergraduate introductory courses, using thermoelectric modules and a real-time data acquisition system. The device may be made at low cost, still providing an easy approach to the investigation of liquid-solid and liquid-vapour phase transitions and of metastable states…

  4. Behaviour of carbon dioxide and water vapour flux densities from a disturbed raised peat bog

    NARCIS (Netherlands)

    Nieveen, J.P.; Jacobs, A.F.G.

    2002-01-01

    Measurements of carbon dioxide and water vapour flux densities were carried out for a disturbed raised peat bog in the north of the Netherlands during an 18 month continuous experiment. Tussock grass (sp. Molinea caerulae) mainly dominated the vegetation of the bog area. The maximum leaf area index

  5. Observation of Electromagnetically Induced Transparency in a Zeeman-Sublevel System in Rubidium Atomic Vapour

    Institute of Scientific and Technical Information of China (English)

    肖峰; 郭瑞民; 陈帅; 张宇; 李路明; 陈徐宗

    2003-01-01

    We observed electromagnetically induced transparency (EIT) in a Zeeman-sublevel system using rubidium atomic vapour at the temperature of 75℃, in which the width of the EIT signal is only 0.6 MHz. Two different methods were performed to observe the EIT signal in our experiment.

  6. Experimental Demonstration of Electromagnetic Induced Transparency and Dispersion Effects in Cs Atom Vapour

    Institute of Scientific and Technical Information of China (English)

    张俊香; 董瑞芳; 常宏; 谢常德; 彭忻墀; 肖敏

    2001-01-01

    The effects of the electromagnetically induced transparency and dispersion of a A-type three-level atomic system are experimentally measured with a vapour cell of Cs atoms. The steep dispersion at low absorption is observed. Thus a small group velocity for the probe beam is inferred from the measured dispersion curve.

  7. The radiative impact of major volcanic eruptions on stratospheric water vapour

    Science.gov (United States)

    Löffler, Michael; Brinkop, Sabine; Jöckel, Patrick

    2016-04-01

    Volcanic eruptions can have significant impact on the earth's weather and climate system. Besides the subsequent tropospheric changes also the stratosphere is influenced by large eruptions. Here changes in stratospheric water vapour after the two major volcanic eruptions of El Chichón in Mexico in 1982 and Mount Pinatubo on the Philippines in 1991 are investigated with chemistry-climate model simulations. This study is based on two simulations with specified dynamics of the EMAC model, performed within the Earth System Chemistry integrated Modelling (ESCiMo) project, of which only one includes the volcanic forcing through prescribed aerosol optical properties. The results show a significant increase in stratospheric water vapour after the eruptions, resulting from increased heating rates and the subsequent changes in stratospheric and tropopause temperatures in the tropics. The tropical vertical advection and the South Asian summer monsoon are identified as important sources for the additional water vapour in the stratosphere. Additionally, volcanic influences on the tropospheric water vapour and ENSO are evident.

  8. The beauty of frost: nano-sulfur assembly via low pressure vapour deposition.

    Science.gov (United States)

    Wang, Yu; Chen, Lu; Scudiero, Louis; Zhong, Wei-Hong

    2015-11-14

    A low pressure vapour deposition (LPVD) technique is proposed as an environmentally friendly, cost-effective and versatile strategy for fabrication of sulfur nanomaterials. By controlling the characteristics of the deposit substrate for the LPVD, various sulfur-based nanomaterials have been obtained through a substrate-induced self-assembly process.

  9. Properties of alumina films by atmospheric pressure metal-organic chemical vapour deposition

    NARCIS (Netherlands)

    Haanappel, V.A.C.; Corbach, van H.D.; Fransen, T.; Gellings, P.J.

    1994-01-01

    Thin alumina films were deposited at low temperatures (290–420°C) on stainless steel, type AISI 304. The deposition process was carried out in nitrogen by metal-organic chemical vapour deposition using aluminum tri-sec-butoxide. The film properties including the protection of the underlying substrat

  10. The mechanical properties of thin alumina film deposited by metal-organic chemical vapour deposition

    NARCIS (Netherlands)

    Haanappel, V.A.C.; Gellings, P.J.; Vendel, van de D.; Metselaar, H.S.C.; Corbach, van H.D.; Fransen, T.

    1995-01-01

    Amorphous alumina films were deposited by metal-organic chemical vapour deposition (MOCVD) on stainless steel, type AISI 304. The MOCVD experiments were performed in nitrogen at low and atmospheric pressures. The effects of deposition temperature, growth rate and film thickness on the mechanical pro

  11. Expanding thermal plasma chemical vapour deposition of ZnO:Al layers for CIGS solar cells

    NARCIS (Netherlands)

    Sharma, K.; Williams, B.L.; Mittal, A.; Knoops, H.C.M.; Kniknie, B.J.; Bakker, N.J.; Kessels, W.M.M.; Schropp, R.E.I.; Creatore, M.

    2014-01-01

    Aluminium-doped zinc oxide (ZnO:Al) grown by expanding thermal plasma chemical vapour deposition (ETP-CVD) has demonstrated excellent electrical and optical properties, which make it an attractive candidate as a transparent conductive oxide for photovoltaic applications. However, when depositing ZnO

  12. Ground-based near-infrared observations of water vapour in the Venus troposphere

    CERN Document Server

    Chamberlain, S; Crisp, D; Meadows, V S; 10.1016/j.icarus.2012.11.014

    2012-01-01

    We present a study of water vapour in the Venus troposphere obtained by modelling specific water vapour absorption bands within the 1.18 \\mu m window. We compare the results with the normal technique of obtaining the abundance by matching the peak of the 1.18 \\mu m window. Ground-based infrared imaging spectroscopy of the night side of Venus was obtained with the Anglo-Australian Telescope and IRIS2 instrument with a spectral resolving power of R ~ 2400. The spectra have been fitted with modelled spectra simulated using the radiative transfer model VSTAR. We find a best fit abundance of 31 ppmv (-6 + 9 ppmv), which is in agreement with recent results by B\\'ezard et al. 2011 using VEX/SPICAV (R ~ 1700) and contrary to prior results by B\\'ezard et al. 2009 of 44 ppmv (+/-9 ppmv) using VEX/VIRTIS-M (R ~ 200) data analyses. Comparison studies are made between water vapour abundances determined from the peak of the 1.18 \\mu m window and abundances determined from different water vapour absorption features within t...

  13. Orthogonal self-assembly and selective solvent vapour annealing: simplified processing of a photovoltaic blend.

    Science.gov (United States)

    De Luca, Giovanna; Liscio, Andrea; Battagliarin, Glauco; Chen, Long; Scolaro, Luigi Monsù; Müllen, Klaus; Samorì, Paolo; Palermo, Vincenzo

    2013-05-14

    Selective solvent vapour annealing is used on a photovoltaic blend to enhance the interaction between the electron acceptor and the electron donor, simplifying thin films post-processing for photovoltaic applications. A remarkable improvement in the interfacial charge transfer in the bulk hetero-junction is attained, as measured by Kelvin Probe Force Microscopy.

  14. Chlorine-free plasma-based vapour growth of GaN

    Energy Technology Data Exchange (ETDEWEB)

    Siche, D.; Kachel, K.; Zwierz, R.; Golka, S.; Sudhoff, P.; Gogova, D. [Leibniz-Institut fuer Kristallzuechtung, Berlin (Germany); Vodopyanov, A.; Izotov, I.; Sennikov, P.; Golubev, S. [Institute of Applied Physics, Nizhny Novgorod (Russian Federation); Franke, K.P. [Institute fuer Umwelttechnologien GmbH, Berlin (Germany)

    2012-03-15

    In pure physical vapour transport process for GaN growth, the liquid Ga source has to be kept at temperatures about 1300-1400 C to provide sufficient Ga vapour pressure for reasonably large growth rates. The growth temperature needs to be slightly lower to prevent droplet formation in the Ga vapour. At such high temperatures, however, the early ammonia decomposition prevents the favorable growth with reactive nitrogen in excess. The vapour processes under development in this study aim at overcoming the drawbacks of the reaction of physically or chemically transported Ga and ammonia. For this purpose, the reactive nitrogen will be supplied by plasma excitation of N{sub 2}. First, the results on ammonia-based GaN growth and their disadvantages are discussed. Then, the challenges in designing of a new type of plasma sources (a microwave and a dielectric barrier discharge) and the first experimental results on the ammonia-free process development are presented. The microwave approach seems to be very promising in terms of GaN growth. It has higher growth rates than the dielectric barrier discharge method and therefore it is more cost-effective. (copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  15. A computer-controlled system for generation of chemical vapours in in vitro dermal uptake studies.

    Science.gov (United States)

    Rauma, Matias; Johanson, Gunnar

    2007-02-01

    Recent work in our laboratory suggests that dermal absorption and desorption of volatile chemicals may be assessed in vitro by thermogravimetric analysis (TGA), i.e. by passing chemical vapour over a piece of skin while recording the weight increase at constant temperature and humidity. This paper describes a high-precision automated vapour-generating system for use with the TGA equipment. The system consists of computer-controlled magnetic valves and mass flow meters that split and redirect a flow of pure, dry air through different stainless-steel gas wash bottles thermostated to 25.00+/-0.05 degrees C. Each wash bottle is filled with a neat volatile chemical and designed so that the air leaving reaches 100% saturation within seconds, as shown with cyclohexanone. The air leaving the wash bottles are combined and directed via stainless-steel liners to the skin piece in the TGA chamber. The liners are heated to 30 degrees C to prevent condensation of water or chemical. Special computer software was developed to allow automatic runs with different wash bottles (chemicals) and air flows over several days. A number of measurements were made to characterize the stability and reproducibility of the vapour-generating system. We have developed a computer-controlled vapour-generating system for use in measurements of dermal absorption of chemicals by thermal gravimetry. The system has high stability and reproducibility and produces little noise.

  16. Hydrogen and carbon vapour pressure isotope effects in liquid fluoroform studied by density functional theory

    Energy Technology Data Exchange (ETDEWEB)

    Oi, Takao; Mitome, Ryota; Yanase, Satoshi [Sophia Univ., Tokyo (Japan). Faculty of Science and Technology

    2017-06-01

    H/D and {sup 12}C/{sup 13}C vapour pressure isotope effects (VPIEs) in liquid fluoroform (CHF{sub 3}) were studied at the MPW1PW91/6-31 ++ G(d) level of theory. The CHF{sub 3} monomer and CHF{sub 3} molecules surrounded by other CHF{sub 3} molecules in every direction in CHF{sub 3} clusters were used as model molecules of vapour and liquid CHF{sub 3}. Although experimental results in which the vapour pressure of liquid {sup 12}CHF{sub 3} is higher than that of liquid {sup 12}CDF{sub 3} and the vapour pressure of liquid {sup 13}CHF{sub 3} is higher than that of liquid {sup 12}CHF{sub 3} between 125 and 212 K were qualitatively reproduced, the present calculations overestimated the H/D VPIE and underestimated the {sup 12}C/{sup 13}C VPIE. Temperature-dependent intermolecular interactions between hydrogen and fluorine atoms of neighbouring molecules were required to explain the temperature dependences of both H/D and {sup 12}C/{sup 13}C VPIEs.

  17. Supercooled liquid vapour pressures and related thermodynamic properties of polycyclic aromatic hydrocarbons determined by gas chromatography

    NARCIS (Netherlands)

    Haftka, J.J.H.; Parsons, J.R.; Govers, H.A.J.

    2006-01-01

    A gas chromatographic method using Kovats retention indices has been applied to determine the liquid vapour pressure (P-i), enthalpy of vaporization (Delta H-i) and difference in heat capacity between gas and liquid phase (Delta C-i) for a group of polycyclic aromatic hydrocarbons (PAHs). This group

  18. Mercury vapour levels in a domestic environment following breakage of a clinical thermometer.

    Science.gov (United States)

    Smart, E R

    1986-12-01

    Following the breakage of a clinical thermometer in the kitchen of the author's own home, mercury vapour was found to be present in most rooms, but not in concentrations which exceeded the current threshold limit value (TLV). However, assuming a more stringent standard of safety, based on continuous exposure to mercury vapour, it was noted that some of the readings could be considered to be excessive, although these were of a freakish and transient nature. In reality the overall time-weighted average exposure of the occupants was within reasonable limits. Lack of ventilation was a major factor in maintaining discernible levels of vapour over a 3-week period. However, the advent of mild weather was instrumental in dispersing the vapour, by allowing the opening of windows. The residual mercury on the floors would seem to have evaporated, so that no long-term health risk ensued. Cross contamination of the hallway carpet was noted indicating that mercury had been transported on the soles of feet and shoes.

  19. Discovery of water vapour in the carbon star V Cygni from observations with Herschel/HIFI

    NARCIS (Netherlands)

    Neufeld, D. A.; Gonzalez-Alfonso, E.; Melnick, G.; Pulecka, M.; Schmidt, M.; Szczerba, R.; Bujarrabal, V.; Alcolea, J.; Cernicharo, J.; Decin, L.; Dominik, C.; Justtanont, K.; de Koter, A.; Marston, A. P.; Menten, K.; Olofsson, H.; Planesas, P.; Schoier, F. L.; Teyssier, D.; Waters, L. B. F. M.; Edwards, K.; McCoey, C.; Shipman, R.; Jellema, W.; de Graauw, T.; Ossenkopf, V.; Schieder, R.; Philipp, S.

    2010-01-01

    We report the discovery of water vapour toward the carbon star V Cygni. We have used Herschel's HIFI instrument, in dual beam switch mode, to observe the 1(11)-0(00) para-water transition at 1113.3430 GHz in the upper sideband of the Band 4b receiver. The observed spectral line profile is nearly

  20. The effect of air permeability of chemical protective clothing material on clothing vapour resistance

    NARCIS (Netherlands)

    Havenith, G.; Vuister, R.; Wammes, L.

    1996-01-01

    One of the major problems associated with Chemical Warfare Protective Clothing (CW) is the additional heat load created by the garments. For CW-overgarments, research in the direction of reducing material thickness and thus heat and vapour resistance have not resulted in major improvements. The

  1. Vapour cooling of poorly conducting hot substrates increases the dynamic Leidenfrost temperature

    NARCIS (Netherlands)

    Limbeek, van M.A.J.; Shirota, M.; Sleutel, C.P.; Sun, C.; Prosperetti, A.; Lohse, D.

    2016-01-01

    A drop impacting a smooth solid surface heated above the saturation temperature can either touch it (contact boiling) or not (film boiling), depending on the surface temperature. The heat transfer is greatly reduced in the latter case by the insulating vapour layer under the drop. In contrast to pre

  2. Evaluation of the biological efficacy of hydrogen peroxide vapour decontamination in wards of an Australian hospital.

    Science.gov (United States)

    Chan, H-T; White, P; Sheorey, H; Cocks, J; Waters, M-J

    2011-10-01

    This study assessed the efficacy of a 'dry' hydrogen peroxide vapour decontamination in an Australian hospital via a two-armed study. The in vivo arm examined the baseline bacterial counts in high-touch zones within wards and evaluated the efficacy of cleaning with a neutral detergent followed by either hydrogen peroxide vapour decontamination, or a manual terminal clean with bleach or Det-Sol 500. The in vitro arm examined the efficacy of hydrogen peroxide vapour decontamination on a variety of different surfaces commonly found in the wards of an Australian hospital, deliberately seeded with a known concentration of vancomycin-resistant enterococci (VRE). All bacterial counts were evaluated by a protocol of contact plate method. In the in vivo arm, 33.3% of the high-touch areas assessed had aerobic bacterial count below the detection limit (i.e. no bacteria recoverable) post hydrogen peroxide decontamination, and in all circumstances the highest microbial density was ≤3 cfu/cm(2), while in the in vitro arm there was at least a reduction in bacterial load by a factor of 10 at all surfaces investigated. These results showed that dry hydrogen peroxide vapour room decontamination is highly effective on a range of surfaces, although the cleanliness data obtained by these methods cannot be easily compared among the different surfaces as recovery of organisms is affected by the nature of the surface.

  3. Influence of Shrinkage on Air and Water Vapour Permeability of Double-Layered Weft Knitted Fabrics

    Directory of Open Access Journals (Sweden)

    Asta BIVAINYTĖ

    2012-09-01

    Full Text Available Water vapour permeability and transport depends on the properties of the fibre and knitted fabric structure. It was designed double-layered fabrics knitted in plain plating pattern whose inner side was  made from synthetic fibres the PES, PA, PP, and Coolmax® (tetra-channel fibres by DuPont which do not absorb moisture and on the surface of the wear – natural cotton and bamboo fibres which have good absorption properties. In the present research it was established that the air permeability of all fabrics after washing and drying cycle decreased. It occurred because of the influence of shrinkage during washing and drying under the impact of moisture, heat, and mechanical action. After washing and drying cycle, the water vapour permeability of fabrics knitted from bamboo and synthetic yarns blend decreased predominantly and became similar to fabrics knitted from cotton and respective synthetic yarns blend. The water vapour permeability of fabrics knitted from cotton and synthetic yarns blend decreased significant less. Depending on the knitting structure, the most decrease of water vapour permeability was estimated to the plain plated fabrics.DOI: http://dx.doi.org/10.5755/j01.ms.18.3.2438

  4. Vapour Removal from the Greenhouse Using Forced Ventilation when Applying a Thermal Screen

    NARCIS (Netherlands)

    Campen, J.B.

    2008-01-01

    The objective of this study is to dimension a system capable of removing water vapour mainly generated by evaporation of the crop when a thermal screen is applied. The humid greenhouse air is replaced by cold dry outside air using an air distribution system. The dry air is injected above the

  5. Insight from ozone and water vapour on transport in the tropical tropopause layer (TTL

    Directory of Open Access Journals (Sweden)

    F. Ploeger

    2010-10-01

    Full Text Available We explore the potential of ozone observations to constrain transport processes in the tropical tropopause layer (TTL, and contrast it with insights that can be obtained from water vapour. Global fields from Halogen Occultation Experiment (HALOE and in-situ observations are predicted using a backtrajectory approach that captures advection, instantaneous freeze-drying and photolytical ozone production. Two different representations of transport (kinematic and diabatic 3-month backtrajectories based on ERA-Interim data are used to evaluate the sensitivity to differences in transport. Results show that mean profiles and seasonality of both tracers can be reasonably reconstructed. Water vapour predictions are similar for both transport representations, but predictions for ozone are systematically higher for kinematic transport. While for global HALOE observations the diabatic prediction underestimates the vertical ozone gradient, for SCOUT-O3 in-situ observations the kinematic prediction shows a clear high bias above 390 K. We show that ozone predictions and vertical dispersion of the trajectories are highly correlated, rendering ozone an interesting tracer for aspects of transport to which water vapour is not sensitive. We show that dispersion and mean upwelling have similar effects on ozone profiles, with slower upwelling and larger dispersion both leading to higher ozone concentrations. Analyses of tropical upwelling based on mean transport characteristics, and model validation have to take into account this ambiguity. In turn, ozone may provide constraints on aspects of transport in the TTL and lower stratosphere that cannot be obtained from water vapour.

  6. Need for Vapour-Liquid Equilibrium Data Generation of Systems Involving Green Solvents

    Directory of Open Access Journals (Sweden)

    V. M. Parsana

    2015-06-01

    Full Text Available Much has been said and written over the years regarding green chemistry concept and use of green solvents. The green solvents can potentially replace the traditional or classical solvents in order to reduce the environment footprint or their harmful impact on human being and/or environment. Vapour-liquid equilibrium data is indispensable for the design of distillation columns for separation processes which account for a large percentage of total costs in a typical chemical plant. Though extensive approach has been made for the replacement of traditional solvents, but not enough consideration been given for vapour-liquid equilibrium data, required for designing separation processes in case of replacement with green solvents. So this paper aims at encouraging vapour-liquid equilibrium data generation for design of efficient separation for binary systems involving ethereal green solvents such as cyclopentyl methyl ether (CPME and 2-methyl tetrahydrofuran (2-MeTHF. A brief review and outline of procedure for generating vapour-liquid equilibrium data is presented here.

  7. The time variation in infrared water-vapour bands in Mira variables

    NARCIS (Netherlands)

    Matsuura, M; Yamamura, [No Value; Cami, J; Onaka, T; Murakami, H; Yamamura, I.

    2002-01-01

    The time variation in the water-vapour bands in oxygen-rich Mira variables has been investigated using multi-epoch ISO/SWS spectra of four Mira variables in the 2.5-4.0 mum region. All four stars show H2O bands in absorption around minimum in the visual light curve. At maximum, H2O emission features

  8. Solvents for CO2 capture. Structure-activity relationships combined with vapour-liquid-equilibrium measurements

    NARCIS (Netherlands)

    Mergler, Y.L.; Rumley-Van Gurp, R.; Brasser, P.; Koning, M.C. de; Goetheer, E.L.V.

    2011-01-01

    In this study a systematic approach was chosen to test and characterize amine systems for CO2 capture. Vapour-liquid-equilibrium measurements were performed on a homologue series of amines, with ethylene amine as base structure. Various functional groups were used that ranged in chemical and physica

  9. Electromagnetically-induced transparency in a multi-V-type system in cesium atomic vapour

    Institute of Scientific and Technical Information of China (English)

    赵建明; 尹王保; 汪丽蓉; 肖连团; 贾锁堂

    2002-01-01

    Electromagnetically-induced transparency is observed in a three-level multi-V-type system in cesium vapour atroom temperature. The absorption property is measured and the hyperfine structures of atomic states can be determined.The results of the experiment agree with the theoretical analysis.

  10. Expanding thermal plasma chemical vapour deposition of ZnO:Al layers for CIGS solar cells

    NARCIS (Netherlands)

    Sharma, K.; Williams, B.L.; Mittal, A.; Knoops, H.C.M.; Kniknie, B.J.; Bakker, N.J.; Kessels, W.M.M.; Schropp, R.E.I.; Creatore, M.

    2014-01-01

    Aluminium-doped zinc oxide (ZnO:Al) grown by expanding thermal plasma chemical vapour deposition (ETP-CVD) has demonstrated excellent electrical and optical properties, which make it an attractive candidate as a transparent conductive oxide for photovoltaic applications. However, when depositing ZnO

  11. Application of kinetic Monte Carlo method to equilibrium systems: vapour-liquid equilibria.

    Science.gov (United States)

    Ustinov, E A; Do, D D

    2012-01-15

    Kinetic Monte Carlo (kMC) simulations were carried out to describe the vapour-liquid equilibria of argon at various temperatures. This paper aims to demonstrate the potential of the kMC technique in the analysis of equilibrium systems and its advantages over the traditional Monte Carlo method, which is based on the Metropolis algorithm. The key feature of the kMC is the absence of discarded trial moves of molecules, which ensures larger number of configurations that are collected for time averaging. Consequently, the kMC technique results in significantly fewer errors for the same number of Monte Carlo steps, especially when the fluid is rarefied. An additional advantage of the kMC is that the relative displacement probability of molecules is significantly larger in rarefied regions, which results in a more efficient sampling. This provides a more reliable determination of the vapour phase pressure and density in case of non-uniform density distributions, such as the vapour-liquid interface or a fluid adsorbed on an open surface. We performed kMC simulations in a canonical ensemble, with a liquid slab in the middle of the simulation box to model two vapour-liquid interfaces. A number of thermodynamic properties such as the pressure, density, heat of evaporation and the surface tension were reliably determined as time averages. Copyright © 2011 Elsevier Inc. All rights reserved.

  12. Accuracy and conservatism of vapour intrusion algorithms for contaminated land management

    NARCIS (Netherlands)

    Provoost, J.; Reijnders, L.; Bonders, J.

    2013-01-01

    This paper provides a view on the suitability of screening-level vapour intrusion (VI) algorithms for contaminated land management. It focuses on the accuracy and level of conservatism for a number of screening-level algorithms used for VI into buildings. The paper discusses the published evidence o

  13. Fluid-driven fracturing of adhered elastica: evolution of the vapour tip

    Science.gov (United States)

    Ball, Thomasina V.; Neufeld, Jerome A.

    2016-11-01

    The transient spreading of a viscous fluid beneath an elastic sheet is controlled by the dynamics at the tip. The large negative pressures needed to drive the viscous fluid into the narrowing gap necessitates a vapour tip separating the fluid front and the crack tip. Adhesion of the elastic sheet imposes a curvature at the tip giving rise to an elasto-capillary length scale and the possibility of a balance between elastic deformation and the strength of adhesion. Two dynamical regimes are therefore possible; viscosity dominant spreading controlled by the pressure in the vapour tip and adhesion dominant spreading controlled by interfacial adhesion. A series of constant flux experiments using clear PDMS elastic sheets allow for direct measurement of the vapour tip in the bending (thick sheet) limit. For small fluid fluxes, the experimental results can be explained by a constant interior pressure and a viscous boundary layer near the fluid front and result in an asymptotic model for the advance of adhesion and viscosity dominated fracture fronts resolving the vapour tip. Understanding the fluid-driven fracturing of adhered elastica provides insight into the spreading of shallow magmatic intrusions in the Earth's crust, and the fluid-driven fracturing of elastic media more generally.

  14. Indium oxide thin film based ammonia gas and ethanol vapour sensor

    Indian Academy of Sciences (India)

    K K Makhija; Arabinda Ray; R M Patel; U B Trivedi; H N Kapse

    2005-02-01

    A sensor for ammonia gas and ethanol vapour has been fabricated using indium oxide thin film as sensing layer and indium tin oxide thin film encapsulated in poly(methyl methacrylate) (PMMA) as a miniature heater. For the fabrication of miniature heater indium tin oxide thin film was grown on special high temperature corning glass substrate by flash evaporation method. Gold was deposited on the film using thermal evaporation technique under high vacuum. The film was then annealed at 700 K for an hour. The thermocouple attached on sensing surface measures the appropriate operating temperature. The thin film gas sensor for ammonia was operated at different concentrations in the temperature range 323–493 K. At 473 K the sensitivity of the sensor was found to be saturate. The detrimental effect of humidity on ammonia sensing is removed by intermittent periodic heating of the sensor at the two temperatures 323K and 448 K, respectively. The indium oxide ethanol vapour sensor operated at fixed concentration of 400 ppm in the temperature range 293–393 K. Above 373 K, the sensor conductance was found to be saturate. With various thicknesses from 150–300 nm of indium oxide sensor there was no variation in the sensitivity measurements of ethanol vapour. The block diagram of circuits for detecting the ammonia gas and ethanol vapour has been included in this paper.

  15. Water vapour rises from the cooling towers for the ATLAS detector at Point 1

    CERN Multimedia

    Brice, Maximilien

    2015-01-01

    Electronics on the ATLAS detector produce heat when the experiment is running. An elaborate cooling system keeps the detector from overheating. On the surface, the warm water vapour that rises from the detector 100metres underground is clearly visible from the ATLAS cooling towers on the CERN Meyrin site in Switzerland.

  16. Application of lemongrass oil in vapour phase for the effective control of anthracnose of 'Sekaki' papaya.

    Science.gov (United States)

    Ali, A; Wee Pheng, T; Mustafa, M A

    2015-06-01

    To evaluate the potential use of lemongrass essential oil vapour as an alternative for synthetic fungicides in controlling anthracnose of papaya. Lemongrass oil used in the study was characterized using gas chromatography-flame ionization detection (GC-FID) before it was tested against anthracnose of papaya in vitro and in vivo. The GC-FID analysis showed that geranial (45·6%) and neral (34·3%) were the major components in lemongrass oil. In vitro study revealed that lemongrass oil vapour at all concentrations tested (33, 66, 132, 264 and 528 μl l(-1) ) suppressed the mycelial growth and conidial germination of Colletotrichum gloeosporioides. For the in vivo study, 'Sekaki' papaya were exposed to lemongrass oil fumigation (0, 7, 14, 28 μl l(-1) ) for 18 h and at room temperature for 9 days. Lemongrass oil vapour at the concentration of 28 μl l(-1) was most effective against anthracnose of artificially inoculated papaya fruit while quality parameters of papaya were not significantly altered. This suggests that lemongrass oil vapour can control anthracnose disease development on papaya without affecting its natural ripening process. The potential practical application of this technology can reduce reliance on synthetic fungicides for the control of postharvest diseases in papaya. © 2015 The Society for Applied Microbiology.

  17. Hereditary Diffuse Gastric Cancer

    Science.gov (United States)

    ... Hereditary Diffuse Gastric Cancer Request Permissions Hereditary Diffuse Gastric Cancer Approved by the Cancer.Net Editorial Board , 11/2015 What is hereditary diffuse gastric cancer? Hereditary diffuse gastric cancer (HDGC) is an inherited ...

  18. Crystal structure of Hg2SO4 – a redetermination

    Directory of Open Access Journals (Sweden)

    Matthias Weil

    2014-09-01

    Full Text Available The crystal structure of mercury(I sulfate (or mercurous sulfate, Hg2SO4, was re-determined based on modern CCD data. In comparison with the previous determination from Weissenberg film data [Dorm (1969. Acta Chem. Scand. 23, 1607–1615], all atoms were refined with anisotropic displacement parameters, leading to higher precision in terms of bond lengths and angles [e.g. Hg—Hg = 2.5031 (7 compared to 2.500 (3Å]. The structure consists of alternating rows along [001] of Hg22+ dumbbells (generated by inversion symmetry and SO42− tetrahedra (symmetry 2. The dumbbells are linked via short O—Hg—Hg—O bonds to the sulfate tetrahedra into chains extending parallel to [20-1]. More remote O—Hg—Hg—O bonds connect these chains into a three-dimensional framework.

  19. Characterization studies of purified HgI{sub 2} precursors

    Energy Technology Data Exchange (ETDEWEB)

    Schieber, M. E-mail: Schieber@vms.huji.ac.il; Zuck, A.; Sanguinetti, S.; Montalti, M.; Braiman, M.; Melekhov, L.; Nissenbaum, J.; Grilli, E.; Guzzi, M.; Turchetta, R.; Dulinski, W.; Husson, D.; Riester, J.L

    1999-06-01

    The ability of HgI{sub 2} powders, used as precursors in mercuric iodide crystal growth, to produce high-quality detectors may be predicted by non-destructive methods like photoluminescence. In fact, it is possible to correlate the presence and the intensity ratio of specific bands in the photoluminescence spectrum of a HgI{sub 2} crystal to its impurity content and stoichiometry. These quantities determine the detector grade that may be achieved using that starting material. Nine different HgI{sub 2} precursors, obtained by different purification methods, have been characterized. The lowest impurity content is achieved via poly-ethylene treatment, which gives also a powder of relatively good stoichiometric quality.

  20. Mesoscale modelling of water vapour in the tropical UTLS: two case studies from the HIBISCUS campaign

    Directory of Open Access Journals (Sweden)

    V. Marécal

    2007-01-01

    Full Text Available In this study, we evaluate the ability of the BRAMS (Brazilian Regional Atmospheric Modeling System mesoscale model compared to ECMWF global analysis to simulate the observed vertical variations of water vapour in the tropical upper troposphere and lower stratosphere (UTLS. The observations are balloon-borne measurements of water vapour mixing ratio and temperature from micro-SDLA (Tunable Diode Laser Spectrometer instrument. Data from two balloon flights performed during the 2004 HIBISCUS field campaign are used to compare with the mesoscale simulations and to the ECMWF analysis. The observations exhibit fine scale vertical structures of water vapour of a few hundred meters height. The ECMWF vertical resolution (~1 km is too coarse to capture these vertical structures in the UTLS. With a vertical resolution similar to ECMWF, the mesoscale model performs better than ECMWF analysis for water vapour in the upper troposphere and similarly or slightly worse for temperature. The BRAMS model with 250 m vertical resolution is able to capture more of the observed fine scale vertical variations of water vapour compared to runs with a coarser vertical resolution. This is mainly related to: (i the enhanced vertical resolution in the UTLS and (ii to the more detailed microphysical parameterization providing ice supersaturations as in the observations. In near saturated or supersaturated layers, the mesoscale model predicted relative humidity with respect to ice saturation is close to observations provided that the temperature profile is realistic. For temperature, the ECMWF analysis gives good results partly attributed to data assimilation. The analysis of the mesoscale model results showed that the vertical variations of the water vapour profile depends on the dynamics in unsaturated layer while the microphysical processes play a major role in saturated/supersaturated layers. In the lower stratosphere, the ECMWF model and the BRAMS model give very similar

  1. [Experimental Research of Hg (II) Removal from Aqueous Solutions of HgCl2 with Nano-TiO2].

    Science.gov (United States)

    Zhou, Xiong; Zhang, Jin-yang; Wang, Ding-yong; Qin, Cai-qing; Xu, Feng; Luo Cheng-zhong; Yang, Xi

    2016-01-15

    Mercury removal from aqueous solutions of HgCl2 was studied by indoor simulation experiments, and the effects of three different diameter of particles of Nano-TiO2 ( Nano-Titanium Dioxide) at different dosage, pH, adsorption time and the initial concentration of Hg2+ on the mercury adsorption from simulated wastewater were investigated. The single factor experiments showed that the optimal conditions were: 7.5 g x L(-1) of 5 nm TiO2 or 2.0 g x L(-1) of 100 nm TiO2, pH 8.0, initial concentration of Hg2+ 15 x mg x L(-1) adsorption time 5 min, and under these conditions the adsorption rates reached 99.5% and 99.3%, relatively. When the content of 25 nm TiO2 was 10 g x L(-1), and the other conditions were pH 8.0, initial concentration of Hg2+ 15 mg x L(-1), adsorption time 60 min, the adsorption rate was 62.8%. The Hg(II) removal effects of the TiO2 particles with different diameters followed the order of 100 nm TiO2 > 5 nm TiO2 > 25 nm TiO2. Component adsorption results showed that the 5 nm TiO2 component adsorption effect was superior to its single adsorption effect, while there was little difference between 100 nm TiO2 component adsorption effect and its single adsorption effect. The results of orthogonal experiments indicated that the influencing factors of the adsorption rate followed the order of pH > the initial concentration of Hg2+ > time > dosage. The optimal experiment scheme was: pH 8.0, a dosage of 100 nm Nano-TiO2 of 2.0 g x L(-1) an initial Hg2+ concentration of 25 mg x L(-1) and adsorption time of 10 min. Under the experimental conditions, the maximum adsorption rate reached 99.9%, at the same time, the equilibrium concentration of Hg(II) was 0.033 mg x L(-1) adsorptive capacity was 26.95 mg x g(-1). The adsorption isotherm was in line with the Langmuir isotherm equation, indicating that the Hg(II) uptake by 100 nm Nano-TiO2 was typical monolayer adsorption.

  2. Mercury (Hg) burden in children: the impact of dental amalgam.

    Science.gov (United States)

    Al-Saleh, Iman; Al-Sedairi, Al Anoud

    2011-07-15

    The risks and benefits of using mercury (Hg) in dental amalgam have long been debated. This study was designed to estimate Hg body burden and its association with dental amalgam fillings in 182 children (ages: 5-15 years) living in Taif City. Hg was measured in urine (UHg), hair (HHg) and toenails (NHg) by the Atomic Absorption Spectrophotometer with Vapor Generator Accessory system. Urinary Hg levels were calculated as both micrograms per gram creatinine (μg/g creatinine) and micrograms per liter (μg/L). We found that children with amalgam fillings (N=106) had significantly higher UHg-C levels than children without (N=76), with means of 3.763 μg/g creatinine versus 3.457 μg/g creatinine, respectively (P=0.019). The results were similar for UHg (P=0.01). A similar pattern was also seen for HHg, with means of 0.614 μg/g (N=97) for children with amalgam versus 0.242 μg/g (N=74) for those without amalgam fillings (P=0). Although the mean NHg was higher in children without amalgam (0.222 μg/g, N=61) versus those with (0.163 μg/g, N=101), the relationship was not significant (P=0.069). After adjusting for many confounders, the multiple logistic regression model revealed that the levels of UHg-C and HHg were 2.047 and 5.396 times higher, respectively, in children with dental amalgam compared to those without (Pdental amalgam fillings (P=0.003). Despite the controversy surrounding the health impact of dental amalgam, this study showed some evidence that amalgam-associated Hg exposure might be related with symptoms of oral health, such as aphthous ulcer, white patches, and a burning-mouth sensation. Further studies are needed to reproduce these findings. The present study showed that significant numbers of children with or without amalgam had Hg levels exceeding the acceptable reference limits. The detrimental neurobehavioral and/or nephrotoxic effects of such an increased Hg on children should be a cause of concern, and further investigation is warranted. Our

  3. Crystal Growth of Solid Solution HgCdTe Alloys

    Science.gov (United States)

    Lehoczky, Sandor L.

    1997-01-01

    The growth of homogenous crystals of HgCdTe alloys is complicated by the large separation between their liquidus and solidus temperatures. Hg(1-x)Cd(x)Te is representative of several alloys which have electrical and optical properties that can be compositionally tuned for a number of applications. Limitations imposed by gravity during growth and results from growth under reduced conditions are described. The importance of residual accelerations was demonstrated by dramatic differences in compositional distribution observed for different attitudes of the space shuttle that resulted in different steady acceleration components.

  4. [Study on Kinetic of Hg2+ from Wastewater Absorbed by Lemon Residues].

    Science.gov (United States)

    Shen, Wang-qing; Wang, Miao; Yang, Ting

    2016-03-01

    With low price and its superior adsorption performance after modification, currently agricultural waste is used as adsorbent of heavy metals in wastewater, which has become a hot research topic. To study on Hg2+ from wastewater absorbed by lemon residues that has been modified by 15% concentration of sulphuric acid. The pore volume, pore size and other properties of the adsorbent were test. The samples were characterized by differential thermal analysis, IR, electron microscopy and spectroscopy. The result showed that the adsorption rate was controlled by membrane diffusion kinetics that was viewed as the first order kinetics equation of the Lagergren, which was physically absorbed. The adsorption properties of modified lemon residues were improved greatly, and the pore size distribution mainly was medium. There were three losses-weight process. There was a endothermic peak around 66 degrees C and two exotherm near 316 degrees C and 494 degrees C. Basic framework of Lemon residues was not changed and structure of Lemon residues was amorphous; the surface of modified lemon residues loosen and many pores formed, and Hg2+ have been adsorbed effectively.

  5. Properties of meso-Erythritol; phase state, accommodation coefficient and saturation vapour pressure

    Science.gov (United States)

    Emanuelsson, Eva; Tschiskale, Morten; Bilde, Merete

    2016-04-01

    Introduction Saturation vapour pressure and the associated temperature dependence (enthalpy ΔH), are key parameters for improving predictive atmospheric models. Generally, the atmospheric aerosol community lack experimentally determined values of these properties for relevant organic aerosol compounds (Bilde et al., 2015). In this work we have studied the organic aerosol component meso-Erythritol. Methods Sub-micron airborne particles of meso-Erythritol were generated by nebulization from aqueous solution, dried, and a mono disperse fraction of the aerosol was selected using a differential mobility analyser. The particles were then allowed to evaporate in the ARAGORN (AaRhus Atmospheric Gas phase OR Nano particle) flow tube. It is a temperature controlled 3.5 m long stainless steel tube with an internal diameter of 0.026 m (Bilde et al., 2003, Zardini et al., 2010). Changes in particle size as function of evaporation time were determined using a scanning mobility particle sizer system. Physical properties like air flow, temperature, humidity and pressure were controlled and monitored on several places in the setup. The saturation vapour pressures were then inferred from the experimental results in the MATLAB® program AU_VaPCaP (Aarhus University_Vapour Pressure Calculation Program). Results Following evaporation, meso-Erythriol under some conditions showed a bimodal particle size distribution indicating the formation of particles of two different phase states. The issue of physical phase state, along with critical assumptions e.g. the accommodation coefficient in the calculations of saturation vapour pressures of atmospheric relevant compounds, will be discussed. Saturation vapour pressures from the organic compound meso-Erythritol will be presented at temperatures between 278 and 308 K, and results will be discussed in the context of atmospheric chemistry. References Bilde, M. et al., (2015), Chemical Reviews, 115 (10), 4115-4156. Bilde, M. et. al., (2003

  6. Water vapour accumulation mechanisms in the Western Mediterranean Basin and the development of European extreme rainfalls

    Directory of Open Access Journals (Sweden)

    E. Sáez de Cámara

    2011-01-01

    Full Text Available This paper examines the role of a recently described warm season circulation at the middle troposphere of northern Africa and that of the recirculation-accumulation mode of the Western Mediterranean Basin (WMB in the initiation of rainfall episodes in central and eastern Europe. Both of these atmospheric mechanisms can accumulate not only soil dust and pollutants for several days but also water vapour by evaporation both over the subtropical Atlantic and the western and central Mediterranean. Accumulation layers are vented off into the surrounding area after the irruption of perturbations. In particular, this work explores the exportation of water vapour under perturbed conditions associated with the passage of ‘Vb’ cyclones. The exceptional rainfall experienced over large areas of central Europe (Elbe/Danube floods during August 11-13, 2002 is exposed as a case study. The procedure to simulate the mechanisms involves a combination of the Regional Atmospheric Modelling System and HYbrid PArticle Concentration and Transport modelling systems. MODIS water vapour products, radio-soundings, wind profiler radars and surface-satellite precipitation data are used to verify the simulation outputs. Our results show that most of the precipitation occurring in the target area during the initiation and deepening of the episode was very likely originated in an air mass exported from the WMB. After our tracking experiment, that air mass, with an initial Atlantic origin, entered the WMB and circulated during 4 days (August 6-9 within the marine boundary layer and the coastal range of mountains of the WMB, accumulating vapour. Then, most of it was transported on August 10, after the irruption of the 'Vb' cyclone Ilse, through the Italian Peninsula and the Adriatic Sea, across the Western Balkans into the target area. The transported vapour together with evaporation en route initiated the rainfall episode.

  7. Sensitivity of polar stratospheric cloud formation to changes in water vapour and temperature

    Directory of Open Access Journals (Sweden)

    F. Khosrawi

    2015-07-01

    Full Text Available More than a decade ago it was suggested that a cooling of stratospheric temperatures by 1 K or an increase of 1 ppmv of stratospheric water vapour could promote denitrification, the permanent removal of nitrogen species from the stratosphere by solid polar stratospheric cloud (PSC particles. In fact, during the two Arctic winters 2009/10 and 2010/11 the strongest denitrification in the recent decade was observed. Sensitivity studies along air parcel trajectories are performed to test how a future stratospheric water vapour (H2O increase of 1 ppmv or a temperature decrease of 1 K would affect PSC formation. We perform our study based on measurements made during the Arctic winter 2010/11. Air parcel trajectories were calculated 6 days backward in time based on PSCs detected by CALIPSO (Cloud Aerosol Lidar and Infrared Pathfinder satellite observations. The sensitivity study was performed on single trajectories as well as on a trajectory ensemble. The sensitivity study shows a clear prolongation of the potential for PSC formation and PSC existence when the temperature in the stratosphere is decreased by 1 K and water vapour is increased by 1 ppmv. Based on 15 years of satellite measurements (2000–2014 from UARS/HALOE, Envisat/MIPAS, Odin/SMR, Aura/MLS, Envisat/SCIAMACHY and SCISAT/ACE-FTS it is further investigated if there is a decrease in temperature and/or increase of water vapour (H2O observed in the polar regions similar to that observed at midlatitudes and in the tropics. Although in the polar regions no significant trend is found in the lower stratosphere, we found from the observations a correlation between cold winters and enhanced water vapour mixing ratios.

  8. Climatology of middle atmospheric water vapour above the ALOMAR observatory in northern Norway

    Directory of Open Access Journals (Sweden)

    K. Hallgren

    2012-12-01

    Full Text Available We have been observing the water vapour line at 22.235 GHz above ALOMAR in northern Norway (69° N, 16° E since early 1996 with ground-based microwave spectrometers (WASPAM and cWASPAM and will here describe a climatology based on these observations. Maintenance, different spectrometers and upgrades of the hardware have slightly changed the instruments. Therefore great care has been taken to make sure the different datasets are compatible with each other. In order to maximise the sensitivity at high altitude for the older instrument a long integration time (168 h was chosen. The complete dataset was thereafter recompiled into a climatology which describes the yearly variation of water vapour at polar latitudes on a weekly basis. The atmosphere is divided into 16 layers between 40–80 km, each 2.5 km thick. The dataset, spanning 15 yr from 1996 to 2010, enabled us to investigate the long-term behaviour of water vapour at these latitudes. By comparing the measurements from every year to the climatological mean we were also able to look for indications of trends in the dataset at different altitudes during the time period of our observations. In general there is a weak negative trend which differs slightly at different altitudes. There are however no drifts in the annual variation of water vapour from the point of view of onset of summer and winter. We compare our climatology to the reference water vapour profiles from AFGL, a free and easy accessible reference atmosphere. There are strong deviations between our observations and the reference profile, therefore we publish our climatological dataset in a table in the paper.

  9. Influence of spatial and temporal variability of subsurface soil moisture and temperature on vapour intrusion

    Science.gov (United States)

    Bekele, Dawit N.; Naidu, Ravi; Chadalavada, Sreenivasulu

    2014-05-01

    A comprehensive field study was conducted at a site contaminated with chlorinated solvents, mainly trichloroethylene (TCE), to investigate the influence of subsurface soil moisture and temperature on vapour intrusion (VI) into built structures. Existing approaches to predict the risk of VI intrusion into buildings assume homogeneous or discrete layers in the vadose zone through which TCE migrates from an underlying source zone. In reality, the subsurface of the majority of contaminated sites will be subject to significant variations in moisture and temperature. Detailed site-specific data were measured contemporaneously to evaluate the impact of spatial and temporal variability of subsurface soil properties on VI exposure assessment. The results revealed that indoor air vapour concentrations would be affected by spatial and temporal variability of subsurface soil moisture and temperature. The monthly monitoring of soil-gas concentrations over a period of one year at a depth of 3 m across the study site demonstrated significant variation in TCE vapour concentrations, which ranged from 480 to 629,308 μg/m3. Soil-gas wells at 1 m depth exhibited high seasonal variability in TCE vapour concentrations with a coefficient of variation 1.02 in comparison with values of 0.88 and 0.74 in 2 m and 3 m wells, respectively. Contour plots of the soil-gas TCE plume during wet and dry seasons showed that the plume moved across the site, hence locations of soil-gas monitoring wells for human risk assessment is a site specific decision. Subsurface soil-gas vapour plume characterisation at the study site demonstrates that assessment for VI is greatly influenced by subsurface soil properties such as temperature and moisture that fluctuate with the seasons of the year.

  10. Natural Hg isotopic composition of different Hg compounds in mammal tissues as a proxy for in vivo breakdown of toxic methylmercury.

    Science.gov (United States)

    Perrot, Vincent; Masbou, Jeremy; Pastukhov, Mikhail V; Epov, Vladimir N; Point, David; Bérail, Sylvain; Becker, Paul R; Sonke, Jeroen E; Amouroux, David

    2016-02-01

    In the last decade, specific attention has been paid to total mercury (HgT) stable isotopic composition, especially in natural samples such as aquatic organisms, due to its potential to track the cycle of this toxic element in the environment. Here, we investigated Hg Compound Specific stable Isotopic Composition (CSIC) of natural inorganic Hg (iHg) and methylmercury (MMHg) in various tissues of aquatic mammals (Beluga whale from the Arctic marine environment and seals from the freshwater lake Baikal, Russia). In seals' organs the variation in mass dependent fractionation (MDF, δ(202)Hg) for total Hg was significantly correlated to the respective fraction of iHg and MMHg compounds, with MMHg being enriched by ∼ 3‰ in heavier isotopes relative to iHg. On the other hand, we observe insignificant variation in Hg mass independent isotope fractionation (MIF, Δ(199)Hg) among iHg and MMHg in all organs for the same mammal species and MMHg in prey items. MIF signatures suggest that both MMHg and iHg in aquatic mammals have the same origin (i.e., MMHg from food), and are representative of Hg photochemistry in the water column of the mammal ecosystem. MDF signatures of Hg compounds indicate that MMHg is demethylated in vivo before being stored in the muscle, and the iHg formed is stored in the liver, and to a lesser extent in the kidney, before excretion. Thus, Hg CSIC analysis in mammals can be a powerful tool for tracing the metabolic response to Hg exposure.

  11. The peculiar abundance pattern of the new Hg-Mn star HD 30085

    CERN Document Server

    Monier, R; Royer, F; Griffin, R E M

    2015-01-01

    Using high-dispersion, high-quality spectra of HD 30085 obtained with the echelle spectrograph SOPHIE at Observatoire de Haute Provence, we show that this star contains strong lines of the s-process elements Sr II, Y II and Zr II. Line syntheses of the lines yield large overabundances of Sr, Y, Zr which are characteristic of HgMn stars. The Sr-Y-Zr triad of abundances is inverted in HD 30085 compared to that in our solar system. The violation of the odd-even rule suggests that physical processes such as radiative diffusion, chemical fractionation and others must be at work in the atmosphere of HD 30085, and that the atmosphere is stable enough to sustain them.

  12. Fabrication and characteristics of Hg/n-bulk GaN schottky diode

    Directory of Open Access Journals (Sweden)

    Belkadi NABIL

    2015-05-01

    Full Text Available In this work, the electrical characteristics of bulk gallium nitride doped n have been investigated by the current–voltage (I–V and capacitance-voltage (C-V at 300 K temperature. Using the thermionic emission theory, the saturation current, IS (2.45×10-7 A, the ideality factor n (1.13, the barrier height ϕbn (0.65 and the serial resistance RS (670 are determined for our structure (Hg/n-GaN. It has also been calculated the barrier height from C–V experimental data. The determined value is higher (1.24 eV compared with the value obtained from I–V (0.65 eV characteristics, it was found the following electrical parameters, doping concentration (ND = 1.68×1016 cm-3, diffusion voltage (Vd = 1.11 V and density of interface states (Nss.

  13. Diffusion coefficient in photon diffusion theory

    NARCIS (Netherlands)

    Graaff, R; Ten Bosch, JJ

    2000-01-01

    The choice of the diffusion coefficient to be used in photon diffusion theory has been a subject of discussion in recent publications on tissue optics. We compared several diffusion coefficients with the apparent diffusion coefficient from the more fundamental transport theory, D-app. Application to

  14. Diffusion coefficient in photon diffusion theory

    NARCIS (Netherlands)

    Graaff, R; Ten Bosch, JJ

    2000-01-01

    The choice of the diffusion coefficient to be used in photon diffusion theory has been a subject of discussion in recent publications on tissue optics. We compared several diffusion coefficients with the apparent diffusion coefficient from the more fundamental transport theory, D-app. Application to

  15. Steam stripping of the unsaturated zone of contaminated sub-soils: the effect of diffusion/dispersion in the start-up phase

    NARCIS (Netherlands)

    Brouwers, H.J.H.; Gilding, B.H.

    2006-01-01

    The unsteady process of steam stripping of the unsaturated zone of soils contaminated with volatile organic compounds (VOCs) is addressed. A model is presented. It accounts for the effects of water and contaminants remaining in vapour phase, as well as diffusion and dispersion of contaminants in thi

  16. Variations in stable isotope fractionation of Hg in food webs of Arctic lakes.

    Science.gov (United States)

    Gantner, Nikolaus; Hintelmann, Holger; Zheng, Wang; Muir, Derek C

    2009-12-15

    Biotic and abiotic fractionation of mercury (Hg) isotopes has recently been shown to occur in aquatic environments. We determined isotope ratios (IRs) of Hg in food webs (zooplankton, chironomids, Arctic char) and sediments of 10 Arctic lakes from four regions and investigated the extent of Hg isotope fractionation. Hg IRs were analyzed by multicollector inductively coupled plasma mass spectrometry (MC-ICP/MS). Hg mass independent fractionation (MIF; Delta(199)Hg) and mass dependent fractionation (MDF; delta(202)Hg) were calculated and compared among samples. IRs of Hg in sediment were characterized mainly by MDF and low MIF (Delta(199)Hg -0.37 to 0.74 per thousand). However, all biota showed evidence of MIF, most pronounced in zooplankton (Delta(199)Hg up to 3.40 per thousand) and char (Delta(199)Hg up to 4.87 per thousand). Zooplankton takes up highly fractionated MeHg directly from the water column, while benthic organisms are exposed to sedimentary Hg, which contains less fractionated Hg. As evidenced by delta(13)C measurements, benthic chironomids make up a large proportion of char diet, explaining in part why MIF(char) meteor impact crater lake (Pingualuk) reflects a "pure" atmospheric Hg signature, which is modified only by aqueous in-lake processes. All other lakes are also affected by terrestrial Hg inputs and sediment processes.

  17. 46 CFR 53.01-5 - Scope (modifies HG-100).

    Science.gov (United States)

    2010-10-01

    ... Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING HEATING BOILERS General Requirements § 53.01-5 Scope (modifies HG-100). (a) The regulations in this part apply to steam heating boilers, hot water boilers (which include hot water heating boilers and hot water supply...

  18. Decay from the superdeformed bands in {sup 194}Hg

    Energy Technology Data Exchange (ETDEWEB)

    Henry, R.G.; Khoo, T.L.; Carpenter, M.P. [and others

    1995-08-01

    Superdeformed bands in {sup 194}H g were studied using the early implementation of Gammasphere. The response functions for the Ge detectors were measured for the first time as part of this experiment. Experiments were performed with both a backed target (where the residue stopped in the Au backing) and a thin target (where the residue recoiled into vacuum). This will permit measurements of the decay times of the quasicontinuum {gamma}rays. The spectrum in coincidence with the yrast SD band in {sup 194}Hg reveals the same features as found in the quasicontinuum structure in {sup 192}Hg. These features include: statistical {gamma}rays feeding the SD band, a pronounced E2 peak from transitions feeding the SD band, a Ml/E2 bump at low energies that is associated with the last stages of feeding of the superdeformed band, and a quasicontinuous distribution from {gamma}rays linking SD and normal states, including a sizable clustering of strength around 1.7 MeV. The remarkable similarity of the spectra coincident with SD bands in {sup 192,194}Hg provides additional support for a statistical process for decay out of the SD states. This similarity contrasts with differences observed in the spectrum coincident with the SD band in the odd-even {sup 191}Hg, confirming the predictions about the role of pairing (in normal states) in influencing the shape of the decay-out spectrum.

  19. Emission and gain studies of the Tl-Hg excimer

    Energy Technology Data Exchange (ETDEWEB)

    Chilukuri, S.; Nayfeh, M.H.

    1978-11-01

    The pressure and temperature dependence of the Tl-Hg excimer emission in the visible from an rf excited discharge has been studied. The gain of the system in the blue band at 4585 A is probed with an Ar-ion laser. With gain sensitivity limited to 1/2% due to beam steering and defocusing effects, the system has no gain.

  20. Hypotension is 100 mm Hg on the Battlefield

    Science.gov (United States)

    2011-10-01

    corroborate the predictive value of admission metabolic acidosis on patient survival. We also were able to show that an SBP of 110 mm Hg after injury was... metabolic acidosis , complications, length of stay, intensive care unit days, and ventilator days all increased. The implication of our result suggested

  1. Experimental study of 199Hg spin anti-relaxation coatings

    CERN Document Server

    Chowdhuri, Z; Horras, M; Kirch, K; Krempel, J; Lauss, B; Mtchedlishvili, A; Rebreyend, D; Roccia, S; Schmidt-Wellenburg, P; Zsigmond, G

    2013-01-01

    We report on a comparison of spin relaxation rates in a $^{199}$Hg magnetometer using different wall coatings. A compact mercury magnetometer was built for this purpose. Glass cells coated with fluorinated materials show longer spin coherence times than if coated with their hydrogenated homologues. The longest spin relaxation time of the mercury vapor was measured with a fluorinated paraffin wall coating.

  2. Ion Beam Nanostructuring of HgCdTe Ternary Compound

    Science.gov (United States)

    Smirnov, Aleksey B.; Savkina, Rada K.; Udovytska, Ruslana S.; Gudymenko, Oleksandr I.; Kladko, Vasyl P.; Korchovyi, Andrii A.

    2017-05-01

    Systematic study of mercury cadmium telluride thin films subjected to the ion beam bombardment was carried out. The evolution of surface morphology of (111) Hg1 - x Cd x Te ( x 0.223) epilayers due to 100 keV B+ and Ag+ ion irradiation was studied by AFM and SEM methods. X-ray photoelectron spectroscopy and X-ray diffraction methods were used for the investigation of the chemical compound and structural properties of the surface and subsurface region. It was found that in the range of nanoscale, arrays of holes and mounds on Hg0.777Cd0.223Te (111) surface as well as the polycrystalline Hg1 - x Cd x Te cubic phase with alternative compound ( x 0.20) have been fabricated using 100 keV ion beam irradiation of the basic material. Charge transport investigation with non-stationary impedance spectroscopy method has shown that boron-implanted structures are characterized by capacity-type impedance whereas for silver-implanted structures, an inductive-type impedance (or "negative capacitance") is observed. A hybrid system, which integrates the nanostructured ternary compound (HgCdTe) with metal-oxide (Ag2O) inclusions, was fabricated by Ag+ ion bombardment. The sensitivity of such metal-oxide-semiconductor hybrid structure for sub-THz radiation was detected with NEP 4.5 × 10-8 W/Hz1/2at ν ≈ 140 GHz and 296 K without amplification.

  3. Thermodynamics limits the reactivity of BrHg radical with volatile organic compounds

    Science.gov (United States)

    Dibble, Theodore S.; Schwid, Abraham C.

    2016-08-01

    Mercury emissions to the atmosphere primarily consist of Hg(0), which tends not to enter ecosystems until it is oxidized. Atomic bromine initiates oxidation of Hg(0) via the BrHg intermediate, but the further reactions of BrHg are just beginning to be explored. Here we use quantum chemistry to determine that hydrogen abstraction from hydrocarbons by BrHg is so endothermic as to be irrelevant. Bonds between BrHg and carbon atoms are so weak that BrHg addition to carbon-carbon double bonds atoms will be somewhat ineffective in leading to further reactions.

  4. Isotopic Composition of Gaseous Elemental Mercury (Hg0) at Various Sites in Japan

    Science.gov (United States)

    Yamakawa, A.; Moriya, K.; Yoshinaga, J.

    2015-12-01

    Mercury (Hg) is a toxic heavy metal, which exists in various chemical forms in the environmental system. In the atmosphere, Hg exists in three forms (Hg0(g), Hg+2(g), and Hg(p)). Hg0(g) is the dominant species of atmospheric Hg, accounting for >95% of the total Hg in the atmosphere. Because Hg0(g) is highly volatile and has limited solubility in water, it cannot be easily removed by wet or dry deposition processes. Therefore, the residence time of Hg0(g) in the atmosphere is relatively long (1 to 2 years), allowing long-range transport from mercury emission source(s). Conversely, Hg+2(g) and Hg(p) are effectively removed from the atmosphere through wet and dry depositions. The determination of mercury source attribution using quantitative data is challenging because Hg0(g) may be deposited on an area upon oxidation to Hg+2(g) and associated with aerosols and particulates to form Hg(p) while the global cycling of Hg0(g). Over the last decade, the development of analytical methods of highly precise Hg isotopic measurements demonstrated mass-dependent fractionation (MDF) and mass-independent fractionation (MIF) of Hg isotopes in environmental samples. For instance, MDF of Hg isotopes is thought to occur during various natural and industrial Hg transformations. MIF of Hg isotopes is observed during abiotic reduction, photochemical and non-photochemical, and physical and chemical processes. Such processes lead to differences in the Hg isotopic composition of different emission sources, both natural and anthropogenic, and atmospheric processes (i.e., transportation, oxidation/reduction, deposition, and reemission). Therefore, Hg isotopic compositions could be used to trace the sources and processes of atmospheric Hg. For securing the reliability and accuracy of atmospheric Hg isotope data, the methods of collection, pretreatment, and isotopic measurement for Hg0(g) were developed to obtain high recovery yield of samples with no Hg isotopic fractionation during each

  5. Importance of Dissolved Neutral Hg-Sulfides, Energy Rich Organic Matter and total Hg Concentrations for Methyl Mercury Production in Sediments

    Science.gov (United States)

    Drott, A.; Skyllberg, U.

    2007-12-01

    Methyl mercury (MeHg) is the mercury form that biomagnifies to the greatest extent in aquatic food webs. Therefore information about factors determining MeHg concentrations is critical for accurate risk assessment of contaminated environments. The concentration of MeHg in wetlands and sediments is the net result of: 1) methylation rates, 2) demethylation rates, and 3) input/output processes. In this study, the main controls on Hg methylation rates and total concentrations of MeHg, were investigated at eight sites in Sweden with sediments that had been subjected to local Hg contamination either as Hg(0), or as phenyl-Hg. Sediments were selected to represent a gradient in total Hg concentration, temperature climate, salinity, primary productivity, and organic C content and quality. Most sediments were high in organic matter content due to wood fibre efflux from pulp and paper industry. The pore water was analysed for total Hg, MeHg, DOC, H2S(aq), pH, DOC, Cl and Br. The chemical speciation of Hg(II) and MeHg in pore water was calculated using equilibrium models. Potential methylation and demethylation rates in sediments were determined in incubation experiments at 23° C under N2(g) for 48 h, after addition of isotopically enriched 201Hg(II) and Me204Hg. In all surface (0-20 cm) sediments there was a significant (pproduction overruled degradation and input/output processes of MeHg in surface sediments, and that % MeHg in surface sediments may be used as a proxy for net production of MeHg. To our knowledge, these are the first data showing significant positive relationships between short term (48 h) MeHg production and longer term accumulation of MeHg, across a range of sites with different properties (1). If MeHg was not normalized to total Hg, the relationship was not significant. For sub-sets of brackish waters (pproductivity freshwaters (pproductivity freshwater (p=0.048, n=6), the sum of neutral Hg-sulfides [Hg(SH)20 (aq)] and [HgS0 (aq)] in the sediment pore

  6. Growth, properties and applications of HgCdTe

    Science.gov (United States)

    Schmit, J. L.

    1983-12-01

    This paper provides primarily a review of the methods used to grow HgCdTe with a summary of some of its basic properties and applications. Methods of crystal growth fall generally into three classes: growth from the melt, from solution and from the vapor phase. All three methods have been and are being used to grow HgCdTe. The high vapor pressure of HgCdTe at the melting point, combined with a large segregation coefficient, have effectively limited the use of Czochralski or zone melting techniques, but two melt growth techniques have survived: (1) a variation of Bridgman growth called quench-anneal wherein a dendritic crystal is formed by quenching the melt and is homogenized by solid state recrystallization below the melting point, (2) a variation of freezing from a large volume called slush-growth wherein a melt is held in a temperature gradient for several weeks while a crystal grows. Growth from solution has taken the form of liquid phase epitaxy (LPE) on CdTe with the LPE systems including growth from Hg-rich, HgTe-rich and Te-rich solutions and using tipping, vertical dipping, vertical sliding and horizontal sliding. Vapor phase growth is very promising but is not yet in production. Techniques include growth by isothermal close spaced epitaxy in which HgTe is transported isothermally by chemical potential onto CdTe, molecular beam epitaxy (MBE) in which elements are evaporated in a high vacuum, and metal organic chemical vapor deposition (MOCVD) in which some of the metal atoms are carried to the substrate bound to organic radicals before being freed by pyrolysis. In all these methods, control of Hg pressure is a major concern. The fundamental properties discussed briefly are those of prime interest to detector manufacturers: energy gap ( Eg), intrinsic carrier concentration ( ni), and electrical activity of dopants. A reasonable fit to the Eg data from ˜ 20 papers is given by Eg = -0.302+1.93x+5.35×10 -4T(1-2x)-0.810x 2+0.832x 3. This gap, combined with k

  7. Formation of PdHg by reaction of palladium thin film contacts deposited onto mercuric iodide ({alpha}-HgI{sub 2}) radiation detector crystals

    Energy Technology Data Exchange (ETDEWEB)

    Medlin, D.L. [Sandia National Labs., Livermore, CA (United States); Van Scyoc, J.M. [Carnegie-Mellon Univ., Pittsburgh, PA (United States). Dept. of Electrical and Computer Engineering; Gilbert, T.S. [Carnegie-Mellon Univ., Pittsburgh, PA (United States). Dept. of Electrical and Computer Engineering; Schlesinger, T.E. [Carnegie-Mellon Univ., Pittsburgh, PA (United States). Dept. of Electrical and Computer Engineering; Boehme, D. [Sandia National Labs., Livermore, CA (United States); Schieber, M. [Sandia National Labs., Livermore, CA (United States); Natarajan, M. [TN Technologies, Inc., Round Rock, TX (United States); James, R.B. [Sandia National Labs., Livermore, CA (United States)

    1996-10-01

    The microstructure and phase distribution of palladium thin films sputter deposited onto {alpha}-HgI{sub 2} for use as electrical contacts in radiation detectors are investigated using electron microscopy. Our results show a limited reaction to form palladium mercuride (PdHg). It is shown that the formation of PdHg via several reaction pathways is thermodynamically feasible. (orig.).

  8. Middle atmospheric water vapour and dynamics in the vicinity of the polar vortex during the Hygrosonde-2 campaign

    OpenAIRE

    S. Lossow; M. Khaplanov; Gumbel, J.; Stegman, J.; G. Witt; Dalin, P.; Kirkwood, S.; F. J. Schmidlin; K. H. Fricke; U. Blum

    2009-01-01

    The Hygrosonde-2 campaign took place on 16 December 2001 at Esrange/Sweden (68° N, 21° E) with the aim to investigate the small scale distribution of water vapour in the middle atmosphere in the vicinity of the Arctic polar vortex. In situ balloon and rocket-borne measurements of water vapour were performed by means of OH fluorescence hygrometry. The combined measurements yielded a high resolution water vapour profile up to an altitude of 75 km. Using the characteristic of wat...

  9. Evaluation of niobium dimethylamino-ethoxide for chemical vapour deposition of niobium oxide thin films

    Energy Technology Data Exchange (ETDEWEB)

    Dabirian, Ali [Laboratory for Photonic Materials and Characterization, Ecole Polytechnique Fédérale de Lausanne (EPFL), Station 17, 1015 Lausanne (Switzerland); Kuzminykh, Yury, E-mail: yury.kuzminykh@empa.ch [Laboratory for Photonic Materials and Characterization, Ecole Polytechnique Fédérale de Lausanne (EPFL), Station 17, 1015 Lausanne (Switzerland); Laboratory for Advanced Materials Processing, Empa, Swiss Federal Laboratories for Materials Science and Technology, Feuerwerkerstrasse 39, 3602 Thun (Switzerland); Wagner, Estelle; Benvenuti, Giacomo [3D-Oxides, 70 Rue G. Eiffel Technoparc, 01630 St Genis Pouilly (France); ABCD Technology, 12 route de Champ-Colin, 1260 Nyon (Switzerland); Rushworth, Simon [Tyndall National Institute, Lee Maltings, Dyke Parade, Cork (Ireland); Hoffmann, Patrik, E-mail: patrik.hoffmann@empa.ch [Laboratory for Photonic Materials and Characterization, Ecole Polytechnique Fédérale de Lausanne (EPFL), Station 17, 1015 Lausanne (Switzerland); Laboratory for Advanced Materials Processing, Empa, Swiss Federal Laboratories for Materials Science and Technology, Feuerwerkerstrasse 39, 3602 Thun (Switzerland)

    2014-11-28

    Chemical vapour deposition (CVD) processes depend on the availability of suitable precursors. Precursors that deliver a stable vapour pressure are favourable in classical CVD processes, as they ensure process reproducibility. In high vacuum CVD (HV-CVD) process vapour pressure stability of the precursor is of particular importance, since no carrier gas assisted transport can be used. The dimeric Nb{sub 2}(OEt){sub 10} does not fulfil this requirement since it partially dissociates upon heating. Dimethylamino functionalization of an ethoxy ligand of Nb(OEt){sub 5} acts as an octahedral field completing entity and leads to Nb(OEt){sub 4}(dmae). We show that Nb(OEt){sub 4}(dmae) evaporates as monomeric molecule and ensures a stable vapour pressure and, consequently, stable flow. A set of HV-CVD experiments were conducted using this precursor by projecting a graded molecular beam of the precursor onto the substrate at deposition temperatures from 320 °C to 650 °C. Film growth rates ranging from 8 nm·h{sup −1} to values larger than 400 nm·h{sup −1} can be obtained in this system illustrating the high level of control available over the film growth process. Classical CVD limiting conditions along with the recently reported adsorption–reaction limited conditions are observed and the chemical composition, and microstructural and optical properties of the films are related to the corresponding growth regime. Nb(OEt){sub 4}(dmae) provides a large process window of deposition temperatures and precursor fluxes over which carbon-free and polycrystalline niobium oxide films with growth rates proportional to precursor flux are obtained. This feature makes Nb(OEt){sub 4}(dmae) an attractive precursor for combinatorial CVD of niobium containing complex oxide films that are finding an increasing interest in photonics and photoelectrochemical water splitting applications. The adsorption–reaction limited conditions provide extremely small growth rates comparable to an

  10. Mercury(II) and methyl mercury determinations in water and fish samples by using solid phase extraction and cold vapour atomic absorption spectrometry combination.

    Science.gov (United States)

    Tuzen, Mustafa; Karaman, Isa; Citak, Demirhan; Soylak, Mustafa

    2009-07-01

    A method has been developed for mercury(II) and methyl mercury speciation on Staphylococcus aureus loaded Dowex Optipore V-493 micro-column in the presented work, by using cold vapour atomic absorption spectrometry. Selective and sequential elution with 0.1 molL(-1) HCl for methyl mercury and 2 molL(-1) HCl for mercury(II) were performed at the pH range of 2-6. Optimal analytical conditions including pH, amounts of biosorbent, sample volumes were investigated. The detection limits of the analytes were 2.5 ngL(-1) for Hg(II) and 1.7 ngL(-1) for methyl mercury. The capacity of biosorbent for mercury(II) and methyl mercury was 6.5 and 5.4 mgg(-1), respectively. The validation of the presented procedure is performed by the analysis of standard reference material. The speciation procedure established was successfully applied to the speciation of mercury(II) and methyl mercury in natural water and microwave digested fish samples.

  11. Survey of trace elements (Al, As, Cd, Cr, Co, Hg, Mn, Ni, Pb, Se, and Si) in retail samples of flavoured and bottled waters.

    Science.gov (United States)

    Barroso, M F; Ramos, S; Oliva-Teles, M T; Delerue-Matos, C; Sales, M G F; Oliveira, M B P P

    2009-01-01

    Concentrations of eleven trace elements (Al, As, Cd, Cr, Co, Hg, Mn, Ni, Pb, Se, and Si) were measured in 39 (natural and flavoured) water samples. Determinations were performed using graphite furnace electrothermetry for almost all elements (Al, As, Cd, Cr, Co, Mn, Ni, Pb, and Si). For Se determination hydride generation was used, and cold vapour generation for Hg. These techniques were coupled to atomic absorption spectrophotometry. The trace element content of still or sparkling natural waters changed from brand to brand. Significant differences between natural still and natural sparkling waters (p differences between flavoured and natural waters. The concentration of each element was compared with the presence of flavours, preservatives, acidifying agents, fruit juice and/or sweeteners, according to the labelled composition. It was shown that flavoured waters generally increase the trace element content. The addition of preservatives and acidifying regulators had a significant influence on Mn, Co, As and Si contents (p difference in Mn, Co, Se and Si content.

  12. Comparison of the characteristics and mechanisms of Hg(II) sorption by biochars and activated carbon.

    Science.gov (United States)

    Xu, Xiaoyun; Schierz, Ariette; Xu, Nan; Cao, Xinde

    2016-02-01

    Two biochars were produced from bagasse and hickory chips (referred to as BB and HCB, respectively) and evaluated for their sorption ability of Hg(II) in aqueous solution. A commercial activated carbon (AC) which is commonly used for Hg(II) removal was included for comparison. Both biochars showed higher sorption capacities than AC, following the trend of BB>HCB>AC. The sorption of Hg(II) by BB and AC was mainly attributed to the formation of (COO)2Hg(II) and (O)2Hg(II). As a result, the adsorption capacity of Hg(II) by BB decreased 17.6% and 37.6% after COOH and OH were blocked, respectively and that of Hg(II) by AC decreased 6.63% and 62.2% for COOH and OH hindered, respectively. However, blocking the function groups had little effect on the Hg removal by HCB since sorption of Hg(II) by HCB was mainly resulted from the π electrons of CC and CO induced Hg-π binding. Further X-ray photoelectron spectroscopy analysis indicated the possibility of reduction of the Hg(II) to Hg(I) by phenol groups or π electrons during the removal of Hg(II) by both biochars. In conclusion, biochar is more effective than activated carbon in removing Hg(II) and there exists a high potential that biochar can be a substitute of activated carbon for removal of Hg(II) from wastewater.

  13. Beer Law Constants and Vapor Pressures of HgI2 over HgI2(s,l)

    Science.gov (United States)

    Su, Ching-Hua; Zhu, Shen; Ramachandran, N.; Burger, A.

    2002-01-01

    Optical absorption spectra of the vapor phase over HgI2(s,l) were measured at sample temperatures between 349 and 610 K for wavelengths between 200 and 600 nm. The spectra show the samples sublimed congruently into HGI2 without any observed Hg or I2 absorption spectra. The Beer's Law constants for 15 wavelengths between 200 and 440 nm were derived. From these constants the vapor pressure of HgI2, P, was found to be a function of temperature for the liquid and the solid beta-phases: ln P(atm) = -7700/T(K) + 12.462 (liquid phase) and ln P(atm) = -10150/T(K) + 17.026 (beta-phase). The expressions match the enthalpies of vaporization and sublimation of 15.30 and 20.17 kcal/mole respectively, for the liquid and the beta-phase HgI2. The difference in the enthalpies gives an enthalpy of fusion of 4.87 kcal/mole, and the intersection of the two expressions gives a melting point of 537 K.

  14. Diffusion of gallium in cadmium telluride

    Energy Technology Data Exchange (ETDEWEB)

    Blackmore, G.W. (Royal Signals and Radar Establishment, Malvern (United Kingdom)); Jones, E.D. (Coventry Polytechnic (United Kingdom)); Mullin, J.B. (Electronics Materials Consultant, West Malvern (United Kingdom)); Stewart, N.M. (BT Labs., Martlesham Heath, Ipswich (United Kingdom))

    1993-01-30

    The diffusion of Ga into bulk-grown, single crystal slices of CdTe was studied in the temperature range 350-811degC where the diffusion anneals were carried out in sealed silica capsules using three different types of diffusion sources. These were: excess Ga used alone, or with either excess Cd or excess Te added to the Ga. Each of the three sets of conditions resulted in different types of concentration profile. At temperatures above 470degC, a function composed of the sum of two complementary error functions gave the best fit to the profiles, whereas below this temperature a function composed of the sum of one or more exponentials of the form exp(-ax) gave the best fit. The behaviour of the diffusion of Ga in CdTe is complex, but it can be seen that two diffusion mechanisms are operating. The first is where D appears to decrease with Cd partial pressure, which implies that the diffusion mechanism may involve Cd vacancies, and a second which is independent of Cd partial pressure. The moderate values of D obtained, confirms that CdTe buffer layers may be useful in reducing Ga contamination in (Hg[sub x]Cd[sub 1-x])Te epitaxial devices grown on GaAs substrates. (orig.).

  15. Elemental Mercury Diffusion Processes and Concentration at the Lunar Poles

    Science.gov (United States)

    Moxley, Frederick; Killen, Rosemary M.; Hurley, Dana M.

    2011-01-01

    In 2009, the Lyman Alpha Mapping Project (LAMP) spectrograph onboard the Lunar Reconnaissance Orbiter (LRO) spacecraft made the first detection of element mercury (Hg) vapor in the lunar exosphere after the Lunar Crater Observing and Sensing Satellite (LCROSS) Centaur rocket impacted into the Cabeus crater in the southern polar region of the Moon. The lunar regolith core samples from the Apollo missions determined that Hg had a devolatilized pattern with a concentration gradient increasing with depth, in addition to a layered pattern suggesting multiple episodes of burial and volatile loss. Hg migration on the lunar surface resulted in cold trapping at the poles. We have modeled the rate at which indigenous Hg is lost from the regolith through diffusion out of lunar grains. We secondly modeled the migration of Hg vapor in the exosphere and estimated the rate of cold-trapping at the poles using a Monte Carlo technique. The Hg vapor may be lost from the exosphere via ionization, Jeans escape, or re-impact into the surface causing reabsorption.

  16. Diffusion archeology for diffusion progression history reconstruction.

    Science.gov (United States)

    Sefer, Emre; Kingsford, Carl

    2016-11-01

    Diffusion through graphs can be used to model many real-world processes, such as the spread of diseases, social network memes, computer viruses, or water contaminants. Often, a real-world diffusion cannot be directly observed while it is occurring - perhaps it is not noticed until some time has passed, continuous monitoring is too costly, or privacy concerns limit data access. This leads to the need to reconstruct how the present state of the diffusion came to be from partial diffusion data. Here, we tackle the problem of reconstructing a diffusion history from one or more snapshots of the diffusion state. This ability can be invaluable to learn when certain computer nodes are infected or which people are the initial disease spreaders to control future diffusions. We formulate this problem over discrete-time SEIRS-type diffusion models in terms of maximum likelihood. We design methods that are based on submodularity and a novel prize-collecting dominating-set vertex cover (PCDSVC) relaxation that can identify likely diffusion steps with some provable performance guarantees. Our methods are the first to be able to reconstruct complete diffusion histories accurately in real and simulated situations. As a special case, they can also identify the initial spreaders better than the existing methods for that problem. Our results for both meme and contaminant diffusion show that the partial diffusion data problem can be overcome with proper modeling and methods, and that hidden temporal characteristics of diffusion can be predicted from limited data.

  17. Vapour pressure and enthalpy of vaporization of aliphatic poly-amines

    Energy Technology Data Exchange (ETDEWEB)

    Efimova, Anastasia A.; Emel' yanenko, Vladimir N. [Department of Physical Chemistry, University of Rostock, Dr-Lorenz-Weg 1, D-18059 Rostock (Germany); Verevkin, Sergey P., E-mail: sergey.verevkin@uni-rostock.d [Department of Physical Chemistry, University of Rostock, Dr-Lorenz-Weg 1, D-18059 Rostock (Germany); Chernyak, Yury [Huntsman Corporation, Advanced Technology Center, 8600 Gosling Road, The Woodlands, 77381 TX (United States)

    2010-03-15

    Molar enthalpies of vaporization of aliphatic poly-amines: 1,4-dimethylpiperazine [106-58-1], 1-(2-aminoethyl)-piperazine, [140-31-8], 1-(2-aminoethyl)-4-methyl-piperazine [934-98-5], and triethylenetetramine [112-24-3] were obtained from the temperature dependence of the vapour pressure measured by the transpiration method. A large number of the primary experimental results on temperature dependences of vapour pressures of the parent compounds have been collected from the literature and have been treated uniformly in order to derive vaporization enthalpies of poly-amines at the reference temperature 298.15 K. An internal consistency check was performed on enthalpy of vaporization values for poly-amines studied in this work.

  18. Coal tar creosote abuse by vapour inhalation presenting with renal impairment and neurotoxicity: a case report

    Science.gov (United States)

    Hiemstra, Thomas F; Bellamy, Christopher OC; Hughes, Jeremy H

    2007-01-01

    A 56 year old aromatherapist presented with advanced renal failure following chronic coal tar creosote vapour inhalation, and a chronic tubulo-interstitial nephritis was identified on renal biopsy. Following dialysis dependence occult inhalation continued, resulting in seizures, ataxia, cognitive impairment and marked generalised cerebral atrophy. We describe for the first time a case of creosote abuse by chronic vapour inhalation, resulting in significant morbidity. Use of the polycyclic aromatic hydrocarbon-containing wood preservative coal tar creosote is restricted by many countries due to concerns over environmental contamination and carcinogenicity. This case demonstrates additional toxicities not previously reported with coal tar creosote, and emphasizes the health risks of polycyclic aromatic hydrocarbon exposure. PMID:17892538

  19. Acoustic emission noise from sodium vapour bubble collapsing: detection, interpretation, modelling and simulation

    Energy Technology Data Exchange (ETDEWEB)

    Dentico, G.; Pacilio, V.; Papalia, B.; Taglienti, S.; Tosi, V.

    1982-01-01

    Sodium vapour bubble collapsing is detected by means of piezoelectric accelorometers coupled to the test section via short waveguides. The output analog signal is processed by transforming it into a time series of pulses through the setting of an amplitude threshold and the shaping of a standard pulse (denominated 'event') every time the signal crosses that border. The number of events is counted in adjacent and equal time duration samples and the waiting time distribution between contiguous events is measured. Up to the moment, six kinetic properties have been found for the mentioned time series. They help in setting a stochastic model in which the subministration of energy into a liquid sodium medium induces the formation of vapour bubbles and their consequent collapsing delivers acoustic pulses. Finally, a simulation procedure is carried out: a Polya's urn model is adopted for simulating event sequences with a priori established requisites.

  20. An analytical model of Faraday rotation in hot alkali metal vapours

    CERN Document Server

    Kemp, Stefan L; Cornish, Simon L

    2011-01-01

    We report a thorough investigation into the absorptive and dispersive properties of hot caesium vapour, culminating in the development of a simple analytical model for off-resonant Faraday rotation. The model, applicable to all hot alkali metal vapours, is seen to predict the rotation observed in caesium, at temperatures as high as 115 $^{\\circ}$C, to within 1% accuracy for probe light detuned by greater than 2 GHz from the $D_{2}$ lines. We also demonstrate the existence of a weak probe intensity limit, below which the effect of hyperfine pumping is negligible. Following the identification of this regime we validate a more comprehensive model for the absorption and dispersion in the vicinity of the $D_{2}$ lines, implemented in the form of a computer code. We demonstrate the ability of this model to predict Doppler-broadened spectra to within 0.5% rms deviation for temperatures up to 50 $^{\\circ}$C.

  1. Coal tar creosote abuse by vapour inhalation presenting with renal impairment and neurotoxicity: a case report

    Directory of Open Access Journals (Sweden)

    Hiemstra Thomas F

    2007-09-01

    Full Text Available Abstract A 56 year old aromatherapist presented with advanced renal failure following chronic coal tar creosote vapour inhalation, and a chronic tubulo-interstitial nephritis was identified on renal biopsy. Following dialysis dependence occult inhalation continued, resulting in seizures, ataxia, cognitive impairment and marked generalised cerebral atrophy. We describe for the first time a case of creosote abuse by chronic vapour inhalation, resulting in significant morbidity. Use of the polycyclic aromatic hydrocarbon-containing wood preservative coal tar creosote is restricted by many countries due to concerns over environmental contamination and carcinogenicity. This case demonstrates additional toxicities not previously reported with coal tar creosote, and emphasizes the health risks of polycyclic aromatic hydrocarbon exposure.

  2. Development of graphene nanoplatelet embedded polymer microcantilever for vapour phase explosive detection applications

    Energy Technology Data Exchange (ETDEWEB)

    Ray, Prasenjit; Pandey, Swapnil; Ramgopal Rao, V. [Centre of Excellence in Nanoelectronics, Department of Electrical Engineering, Indian Institute of Technology Bombay, Mumbai (India)

    2014-09-28

    In this work, a graphene based strain sensor has been reported for explosive vapour detection applications by exploiting the piezoresistive property of graphene. Instead of silicon based cantilevers, a low cost polymeric micro-cantilever platform has been used to fabricate this strain sensor by embedding the graphene nanoplatelet layer inside the beam. The fabricated devices were characterized for their mechanical and electromechanical behaviour. This device shows a very high gauge factor which is around ~144. Also the resonant frequency of these cantilevers is high enough such that the measurements are not affected by environmental noise. These devices have been used in this work for reliable detection of explosive vapours such as 2,4,6-Trinitrotoluene down to parts-per-billion concentrations in ambient conditions.

  3. Localisation of an unknown number of land mines using a network of vapour detectors.

    Science.gov (United States)

    Chhadé, Hiba Haj; Abdallah, Fahed; Mougharbel, Imad; Gning, Amadou; Julier, Simon; Mihaylova, Lyudmila

    2014-11-06

    We consider the problem of localising an unknown number of land mines using concentration information provided by a wireless sensor network. A number of vapour sensors/detectors, deployed in the region of interest, are able to detect the concentration of the explosive vapours, emanating from buried land mines. The collected data is communicated to a fusion centre. Using a model for the transport of the explosive chemicals in the air, we determine the unknown number of sources using a Principal Component Analysis (PCA)-based technique. We also formulate the inverse problem of determining the positions and emission rates of the land mines using concentration measurements provided by the wireless sensor network. We present a solution for this problem based on a probabilistic Bayesian technique using a Markov chain Monte Carlo sampling scheme, and we compare it to the least squares optimisation approach. Experiments conducted on simulated data show the effectiveness of the proposed approach.

  4. Simulation of the Influences of the Pressure Ratio and Cu Vapour on SF6 Arc Characteristics

    Institute of Scientific and Technical Information of China (English)

    ZHANG Jian; JIA Shenli; LI Xingwen; SHI Zongqian; WANG Lijun

    2009-01-01

    The inlet and outlet pressure of the SF6 high voltage circuit-breaker nozzle are of importance in determining the thermal interruption capability of a breaker.Besides,electrode evaporation is inevitable during the arcing process,which may affect the SF6 arc behaviour significantly.In this study a numerical investigation on the arc characteristics of a supersonic nozzle is carried out,by considering the influence of the pressure ratio between the inlet and outlet,and the Cu vapour.It is demonstrated that a lower inlet pressure may result in a higher arc temperature,a lower arc voltage and a smaller mach number,and Cu vapour from electrode evaporation may cool the arc significantly.

  5. Development of a 22 GHz ground-based spectrometer for middle atmospheric water vapour monitoring

    Directory of Open Access Journals (Sweden)

    Pietro Paolo Bertagnolio

    2012-03-01

    Full Text Available The water Vapour Emission SPectrometer for Antarctica at 22 GHz (VESPA-22 has been designed for long-term middle atmospheric climate change monitoring and satellite data validation. It observes the water vapour spectral line at 22.235 GHz using the balanced beam-switching technique. The receiver antenna has been characterized, showing an HPBW of 3.5° and a sidelobe level 40 dB below the main lobe. The receiver front-end has a total gain of 105 dB and a LNA noise temperature of 125 K. A FFT spectrometer (bandwidth 1 GHz, resolution 63 kHz will be used as back-end, allowing the retrieval of H2O concentration profiles in the 20 to 80 km altitude range. The control I/O interface is based on reconfigurable hardware (USB-CPLD.

  6. Investigation of vapour-liquid nucleation properties for spherical and chain-like fluids by density functional theory

    Institute of Scientific and Technical Information of China (English)

    Fu Dong; Liao Tao

    2007-01-01

    The excess Helmholtz free energy functional for nonpolar chain-like molecules is formulated in terms of a weighted density approximation (WDA) for short-range interactions and a Weaks-Chandler-Andersen (WCA) approximation and a Barker-Henderson (BH) theory for long-range attraction. Within the framework of density functional theory (DFT), vapour-liquid interfacial properties including density profile and surface tension, and vapour-liquid nucleation properties including density profile, work of formation and number of particles are investigated for spherical and chainlike molecules. The obtained vapour-liquid surface tension and the number of particles in critical nucleus for LennardJones (L J) fluids are consistent with the simulation results. The influences of supersaturation, temperature and chain length on vapour-liquid nucleation properties are discussed.

  7. CeO2 thin film as a low-temperature formaldehyde sensor in mixed vapour environment

    Indian Academy of Sciences (India)

    R Pandeeswari; B G Jeyaprakash

    2014-10-01

    Nanostructured cerium oxide thin film was deposited onto the glass substrate under optimized condition using spray-pyrolysis technique. X-ray diffraction result indicates polycrystalline nature of the film with fluorite-type face-centered-cubic structure. The atomic force micrograph indicates the presence of nanocrystallites over the film surface. The vapour sensing characteristics of the annealed film were studied by chemiresistive method for various concentrations of formaldehyde vapour at room temperature (∼ 30 °C). For 0.5 ppm of formaldehyde vapour, the film shows a response and recovery time of 36 and 1 s, respectively. The vapour sensing properties of the cerium oxide film in mixed environment were studied and reported.

  8. Remote sensing of water vapour profiles in the framework of the Total Carbon Column Observing Network (TCCON

    Directory of Open Access Journals (Sweden)

    M. Schneider

    2010-12-01

    Full Text Available We show that the near infrared solar absorption spectra recorded in the framework of the Total Carbon Column Observing Network (TCCON can be used to derive the vertical distribution of tropospheric water vapour. The resolution of the TCCON spectra of 0.02 cm−1 is sufficient for retrieving lower and middle/upper tropospheric water vapour concentrations with a vertical resolution of about 3 and 8 km, respectively. We document the good quality of the remotely-sensed profiles by comparisons with coincident in-situ Vaisala RS92 radiosonde measurements. Due to the high measurement frequency, the TCCON water vapour profile data offer novel opportunities for estimating the water vapour variability at different timescales and altitudes.

  9. The 2009 stratospheric major warming described from synergistic use of BASCOE water vapour analyses and MLS observations

    Directory of Open Access Journals (Sweden)

    W. A. Lahoz

    2010-10-01

    Full Text Available The record–breaking major stratospheric warming of northern winter 2009 (January–February is studied using BASCOE (Belgian Assimilation System for Chemical ObsErvation stratospheric water vapour analyses and MLS (Microwave Limb Sounder water vapour observations, together with meteorological data from the European Centre for Medium-Range Weather Forecasts (ECMWF and potential vorticity derived from ECMWF meteorological data. We focus on the interaction between the cyclonic wintertime stratospheric polar vortex and subsidiary anticyclonic stratospheric circulations during the build-up, peak and aftermath of the major warming. We show dynamical consistency between the water vapour analysed fields, and the meteorological and PV fields. New results include the analysis of water vapour during the major warming and demonstration of the benefit of assimilating MLS satellite data into the BASCOE model.

  10. The critical assessment of vapour pressure estimation methods for use in modelling the formation of atmospheric organic aerosol

    Directory of Open Access Journals (Sweden)

    M. H. Barley

    2010-01-01

    Full Text Available A selection of models for estimating vapour pressures have been tested against experimental data for a set of compounds selected for their particular relevance to the formation of atmospheric aerosol by gas-liquid partitioning. The experimental vapour pressure data (all <100 Pa of 45 multifunctional compounds provide a stringent test of the estimation techniques, with a recent complex group contribution method providing the best overall results. The effect of errors in vapour pressures upon the formation of organic aerosol by gas-liquid partitioning in an atmospherically relevant example is also investigated. The mass of organic aerosol formed under typical atmospheric conditions was found to be very sensitive to the variation in vapour pressure values typically present when comparing estimation methods.

  11. Graphene growth from reduced graphene oxide by chemical vapour deposition: seeded growth accompanied by restoration

    OpenAIRE

    2016-01-01

    Understanding the underlying mechanisms involved in graphene growth via chemical vapour deposition (CVD) is critical for precise control of the characteristics of graphene. Despite much effort, the actual processes behind graphene synthesis still remain to be elucidated in a large number of aspects. Herein, we report the evolution of graphene properties during in-plane growth of graphene from reduced graphene oxide (RGO) on copper (Cu) via methane CVD. While graphene is laterally grown from R...

  12. Comparison between Satellite Water Vapour Observations and Atmospheric Models’ Predictions of the Upper Tropospheric Thermal Radiation

    OpenAIRE

    Dim, J. R.; T. Y. Nakajima; T. Takamura; Kikuchi, N

    2011-01-01

    Atmospheric profiles (temperature, pressure, and humidity) are commonly used parameters for aerosols and cloud properties retrievals. In preparation of the launch of the Global Change Observation Mission-Climate/Second-Generation GLobal Imager (GCOM-C/SGLI) satellite, an evaluation study on the sensitivity of atmospheric models to variations of atmospheric conditions is conducted. In this evaluation, clear sky and above low clouds water vapour radiances of the upper troposphere obtained from ...

  13. Occupational mercury vapour poisoning with a respiratory failure, pneumomediastinum and severe quadriparesis

    Science.gov (United States)

    Smiechowicz, Jakub; Skoczynska, Anna; Nieckula-Szwarc, Agata; Kulpa, Katarzyna; Kübler, Andrzej

    2017-01-01

    Objectives: Despite restrictions, mercury continues to pose a health concern. Mercury has the ability to deposit in most parts of the body and can cause a wide range of unspecific symptoms leading to diagnostic mistakes. Methods and results: We report the case of severe mercury vapour poisoning after occupational exposure in a chloralkali plant worker that resulted in life-threatening respiratory failure, pneumomediastinum and quadriparesis. Conclusions: Prolonged mechanical ventilation and treatment with penicillamine and spironolactone was used with successful outcome. PMID:28321305

  14. Vapour-bubble nucleation and dynamics in turbulent Rayleigh–Bénard convection

    NARCIS (Netherlands)

    Narezo Guzman, Daniela; Frączek, T.; Reetz, C.; Sun, C.; Lohse, D.; Ahlers, G.

    2016-01-01

    Vapour bubbles nucleating at micro-cavities etched into the silicon bottom plate of a cylindrical Rayleigh–Bénard sample (diameter $D=8.8$D=8.8 cm, aspect ratio ${\\it\\Gamma}\\equiv D/L\\simeq 1.00$Γ≡D/L≃1.00 where $L$L is the sample height) were visualized from the top and from the side. A triangular

  15. Vapour Liquid Equilibrium in Asymmetric Mixtures of n-Alkanes with Ethane

    OpenAIRE

    Duta, Anca

    2002-01-01

    The paper presents a vapour liquid equilibria study in binary mixtures of n-alkanes with high dimensional asymmetry. Each mixture contains ethane and alkanes higher than eicosane. Calculations were done using two equations of state, Peng-Robinson (PR) and Soave (SRK), in combination with van der Waals mixing rules, corrected with two interaction parameters. A limited temperature dependence of the interaction parameters was found. The correlations between the interaction parameters a...

  16. Improved total atmospheric water vapour amount determination from near-infrared filter measurements with sun photometers

    Directory of Open Access Journals (Sweden)

    F. Mavromatakis

    2007-05-01

    Full Text Available In this work we explore the effect of the contribution of the solar spectrum to the recorded signal in wavelengths outside the typical 940-nm filter's bandwidth. We use gaussian-shaped filters as well as actual filter transmission curves to study the implications imposed by the non-zero out-of-band contribution to the coefficients used to derive precipitable water from the measured water vapour band transmittance. The moderate-resolution SMARTS radiative transfer code is used to predict the incident spectrum outside the filter bandpass for different atmospheres, solar geometries and aerosol optical depths. The high-resolution LBLRTM radiative transfer code is used to calculate the water vapour transmittance in the 940 nm band. The absolute level of the out-of-band transmittance has been chosen to range from 10−6 to 10−4, and typical response curves of commercially available silicon photodiodes are included into the calculations. It is shown that if the out-of-band transmittance effect is neglected, as is generally the case, then the derived columnar water vapour is systematically underestimated by a few percents. The actual error depends on the specific out-of-band transmittance, optical air mass of observation and water vapour amount. We apply published parameterized transmittance functions to determine the filter coefficients. We also introduce an improved, three-parameter, fitting function that can describe the theoretical data accurately, with significantly less residual effects than with the existing functions. Further investigations will use experimental data from field campaigns to validate these findings.

  17. Purification of Single-walled Carbon Nanotubes Grown by a Chemical Vapour Deposition (CVD) Method

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    A procedure for purification of single-walled carbon nanotubes(SWNTs) grown by the chemical vapour deposition (CVD) of carbon monooxide has been developed. Based on the result from TGA/DTA of as-prepared sample, the oxidation temperature was determined. The process included sonication, oxidation and acid washing steps. The purity and yield after purification were determined and estimated by TEM. Moreover, for the first time, a loop structure for CVD SWNTs has been observed.

  18. Quantification of uncertainties of water vapour column retrievals using future instruments

    Directory of Open Access Journals (Sweden)

    H. Diedrich

    2012-09-01

    Full Text Available This study presents a quantification of uncertainties of water vapour retrievals based on near infrared measurements of upcoming instruments. The concepts of three scheduled spectrometer were taken into account: OLCI (Ocean and Land Color Instrument on Sentinel-3, METimage on MetOp (Meteorological Operational Satellite and FCI (Flexible Combined Imager on MTG (Meteosat Third Generation. Optimal estimation theory was used to estimate the error of an hypothetical total water vapour column retrieval for 27 different atmospheric cases. The errors range from 100% in very dry cases to 2% in humid cases with a very high surface albedo. Generally the absolute uncertainties increase with higher water vapour column content due to H2O-saturation and decrease with a brighter surface albedo. Uncertainties increase with higher aerosol optical thickness, apart from very dark cases. Overall the METimage channel setting enables the most accurate retrievals. The retrieval using the MTG-FCI buildup has the highest uncertainties apart from very bright cases.

    A retrieval using two absorption channels increases the accuracy, in some cases by one order of magnitude, in comparison to a retrieval using just one absorption channel. On the other hand, a retrieval using three absorption channels has no significant advantage over a two-absorption channel retrieval.

    Furthermore, the optimal position of the absorption channels was determined using the concept of the "information content". For a single channel retrieval a channel at 900 or 915 nm has the highest mean information contents over all cases. The second absorption channel is ideally weakly correlated with the first one, thus positioned at 935 nm, in a region with stronger water vapour absorption.

  19. Insight from ozone and water vapour on transport in the tropical tropopause layer (TTL

    Directory of Open Access Journals (Sweden)

    F. Ploeger

    2011-01-01

    Full Text Available We explore the potential of ozone observations to constrain transport processes in the tropical tropopause layer (TTL, and contrast it with insights that can be obtained from water vapour. Global fields from Halogen Occultation Experiment (HALOE and in-situ observations are predicted using a backtrajectory approach that captures advection, instantaneous freeze-drying and photolytical ozone production. Two different representations of transport (kinematic and diabatic 3-month backtrajectories based on ERA-Interim data are used to evaluate the sensitivity to differences in transport. Results show that mean profiles and seasonality of both tracers can be reasonably reconstructed. Water vapour predictions are similar for both transport representations, but predictions for ozone are systematically higher for kinematic transport. Compared to global HALOE observations, the diabatic model prediction underestimates the vertical ozone gradient. Comparison of the kinematic prediction with observations obtained during the tropical SCOUT-O3 campaign shows a large high bias above 390 K potential temperature. We show that ozone predictions and vertical dispersion of the trajectories are highly correlated, rendering ozone an interesting tracer for aspects of transport to which water vapour is not sensitive. We show that dispersion and mean upwelling have similar effects on ozone profiles, with slower upwelling and larger dispersion both leading to higher ozone concentrations. Analyses of tropical upwelling based on mean transport characteristics, and model validation have to take into account this ambiguity between tropical ozone production and in-mixing from the stratosphere. In turn, ozone provides constraints on transport in the TTL and lower stratosphere that cannot be obtained from water vapour.

  20. Insight from ozone and water vapour on transport in the tropical tropopause layer (TTL)

    Science.gov (United States)

    Ploeger, F.; Fueglistaler, S.; Grooß, J.-U.; Günther, G.; Konopka, P.; Liu, Y. S.; Müller, R.; Ravegnani, F.; Schiller, C.; Ulanovski, A.; Riese, M.

    2011-01-01

    We explore the potential of ozone observations to constrain transport processes in the tropical tropopause layer (TTL), and contrast it with insights that can be obtained from water vapour. Global fields from Halogen Occultation Experiment (HALOE) and in-situ observations are predicted using a backtrajectory approach that captures advection, instantaneous freeze-drying and photolytical ozone production. Two different representations of transport (kinematic and diabatic 3-month backtrajectories based on ERA-Interim data) are used to evaluate the sensitivity to differences in transport. Results show that mean profiles and seasonality of both tracers can be reasonably reconstructed. Water vapour predictions are similar for both transport representations, but predictions for ozone are systematically higher for kinematic transport. Compared to global HALOE observations, the diabatic model prediction underestimates the vertical ozone gradient. Comparison of the kinematic prediction with observations obtained during the tropical SCOUT-O3 campaign shows a large high bias above 390 K potential temperature. We show that ozone predictions and vertical dispersion of the trajectories are highly correlated, rendering ozone an interesting tracer for aspects of transport to which water vapour is not sensitive. We show that dispersion and mean upwelling have similar effects on ozone profiles, with slower upwelling and larger dispersion both leading to higher ozone concentrations. Analyses of tropical upwelling based on mean transport characteristics, and model validation have to take into account this ambiguity between tropical ozone production and in-mixing from the stratosphere. In turn, ozone provides constraints on transport in the TTL and lower stratosphere that cannot be obtained from water vapour.

  1. Need for Vapour-Liquid Equilibrium Data Generation of Systems Involving Green Solvents

    OpenAIRE

    V. M. Parsana; S. P. Parikh

    2015-01-01

    Much has been said and written over the years regarding green chemistry concept and use of green solvents. The green solvents can potentially replace the traditional or classical solvents in order to reduce the environment footprint or their harmful impact on human being and/or environment. Vapour-liquid equilibrium data is indispensable for the design of distillation columns for separation processes which account for a large percentage of total costs in a typical chemical plant. ...

  2. A microwave satellite water vapour column retrieval for polar winter conditions

    Science.gov (United States)

    Perro, Christopher; Lesins, Glen; Duck, Thomas J.; Cadeddu, Maria

    2016-05-01

    A new microwave satellite water vapour retrieval for the polar winter atmosphere is presented. The retrieval builds on the work of Miao et al. (2001) and Melsheimer and Heygster (2008), employing auxiliary information for atmospheric conditions and numerical optimization. It was tested using simulated and actual measurements from the Microwave Humidity Sounder (MHS) satellite instruments. Ground truth was provided by the G-band vapour radiometer (GVR) at Barrow, Alaska. For water vapour columns less than 6 kg m-2, comparisons between the retrieval and GVR result in a root mean square (RMS) deviation of 0.39 kg m-2 and a systematic bias of 0.08 kg m-2. These results are compared with RMS deviations and biases at Barrow for the retrieval of Melsheimer and Heygster (2008), the AIRS and MIRS satellite data products, and the ERA-Interim, NCEP, JRA-55, and ASR reanalyses. When applied to MHS measurements, the new retrieval produces a smaller RMS deviation and bias than for the earlier retrieval and satellite data products. The RMS deviations for the new retrieval were comparable to those for the ERA-Interim, JRA-55, and ASR reanalyses; however, the MHS retrievals have much finer horizontal resolution (15 km at nadir) and reveal more structure. The new retrieval can be used to obtain pan-Arctic maps of water vapour columns of unprecedented quality. It may also be applied to measurements from the Special Sensor Microwave/Temperature 2 (SSM/T2), Advanced Microwave Sounding Unit B (AMSU-B), Special Sensor Microwave Imager/Sounder (SSMIS), Advanced Technology Microwave Sounder (ATMS), and Chinese MicroWave Humidity Sounder (MWHS) instruments.

  3. Determination of the vapour viscosities of refrigerant mixtures; Bestimmung der Dampfviskositaeten von Kaeltemittelgemischen

    Energy Technology Data Exchange (ETDEWEB)

    Mayinger, E.H.F. [Technische Univ. Muenchen (Germany). Lehrstuhl A fuer Thermodynamik; Nabizadeh, H. [Technische Univ. Muenchen (Germany). Lehrstuhl A fuer Thermodynamik

    1997-02-01

    The research project aimed at the determination of the viscosity of superheated and saturated vapours of the binary fluids R 410A and R 507 and the ternary fluids R 404A and R 407C. (HW) [Deutsch] Es ist das Ziel des Forschungsvorhabens, die Viskositaet gesaettigter und ueberhitzter Daempfe der binaeren Gemische R 410A und R 507, sowie der ternaeren Gemische R 404A und R 407C zu bestimmen. (HW)

  4. Transmission spectroscopy in a thin vapour layer and its derivative properties

    Institute of Scientific and Technical Information of China (English)

    赵延霆; 赵建明; 肖连团; 贾锁堂

    2003-01-01

    A novel method of high-resolution spectroscopy of gases is proposed. The method is based on observing the optical behaviour of thin vapour layer when the particles cross the light beam or collide with the cell walls. The atomic motion and electronic quenching on gas-solid interfaces are explored by numerical analysis. The periodicity of peak values of transmission spectra and its derivative spectra demonstrates a sub-Doppler structure corresponding to the resonant transitions.

  5. Synthesis of Pt nanowires with the participation of physical vapour deposition

    Science.gov (United States)

    Dobrzański, Leszek A.; Szindler, Marek; Pawlyta, Mirosława; Szindler, Magdalena M.; Boryło, Paulina; Tomiczek, Błazej

    2016-01-01

    The following paper presents the possibility of formation of Pt nanowires, achieved by a three-step method consisting of conformal deposition of a carbon nanotube and conformal coverage with platinum by physical vapour deposition, followed by removal of the carbonaceous template. The characterization of this new nanostructure was carried out through scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD).

  6. Synthesis of Pt nanowires with the participation of physical vapour deposition

    Directory of Open Access Journals (Sweden)

    Dobrzański Leszek A.

    2016-01-01

    Full Text Available The following paper presents the possibility of formation of Pt nanowires, achieved by a three-step method consisting of conformal deposition of a carbon nanotube and conformal coverage with platinum by physical vapour deposition, followed by removal of the carbonaceous template. The characterization of this new nanostructure was carried out through scanning electron microscopy (SEM, transmission electron microscopy (TEM and X-ray diffraction (XRD.

  7. Three-dimensional Numerical Investigations on Ejector of Vapour Jet Refrigeration System

    OpenAIRE

    Jiautheen, Parveen Banu; Tiwari, Shaligram; Annamalai, Mani

    2014-01-01

    Vapour Jet Refrigeration System (VJRS) is preferred among various heat operated refrigeration systems because it has potential of utilizing low temperature heat source, consumes less electrical energy causing less atmospheric pollution and requires less maintenance cost due to absence of moving parts [1]. Ejector, a thermal compressor, is one of the crucial components of VJRS. Performance of the whole system is based on the satisfactory operation of the ejector. Hence, it has to be designed c...

  8. Accuracy and conservatism of vapour intrusion algorithms for contaminated land management

    OpenAIRE

    Provoost, J.; Reijnders, L.; Bonders, J.

    2013-01-01

    This paper provides a view on the suitability of screening-level vapour intrusion (VI) algorithms for contaminated land management. It focuses on the accuracy and level of conservatism for a number of screening-level algorithms used for VI into buildings. The paper discusses the published evidence of the accuracy of VI algorithms and puts the conservatism is a broader regulatory perspective, including advice on how to deal with variation. In closing further research needs are provided.

  9. Assessment of micronuclei in lymphocytes from workers exposed to vapours and aerosols of bitumen.

    Science.gov (United States)

    Welge, Peter; Marczynski, Boleslaw; Raulf-Heimsoth, Monika; Spickenheuer, Anne; Kendzia, Benjamin; Heinze, Evelyn; Angerer, Jürgen; Käfferlein, Heiko U; Pesch, Beate; Brüning, Thomas

    2011-06-01

    We investigated the micronucleus frequencies in peripheral blood lymphocytes of 225 mastic asphalt workers (age 17-62 years) and 69 non-bitumen-exposed road construction workers (age 18-64 years) in Germany before and after the working shift. Median shift exposure to vapours and aerosols of bitumen of exposed workers was 3.0 mg/m³. Micronuclei (MN) were determined with a standard method using cytochalasin B. Median MN frequency was 6.0 (interquartile range (IQR) 4.0-8.5) MN/1,000 binucleated lymphocytes (MN/1,000 BNC) in exposed workers and 6.0 (IQR 4.0-8.3) MN/1,000 BNC in non-exposed workers before shift. After shift, we observed 6.5 (IQR 4.4-9.3) MN/1,000 BNC in exposed workers and 6.5 (IQR 4.0-9.0) MN/1,000 BNC in non-exposed workers. Regression models were applied with the log-transformed MN frequency as the dependent variable in order to estimate the effects of exposure to vapours and aerosols of bitumen and of potential confounders. Age was the strongest predictor of MN formation in both exposed workers and referents. Our data suggest that MN formation was not associated with concentration of vapours and aerosols of bitumen during shift at the individual level. Although similar MN frequencies were observed in both groups, the modelling of factors potentially influencing MN frequency revealed a weak group difference in the post-shift model. We conclude that this small difference cannot be judged to be a relevant mutagenic effect of exposure to vapours and aerosols of bitumen, also with regard to the lack of adjustment for multiple testing and the lack of a group effect in the original data.

  10. Characterization of sorption properties of selected soils from Lublin region by using water vapour adsorption method

    Science.gov (United States)

    Skic, Kamil; Boguta, Patrycja; Sokołowska, Zofia

    2016-04-01

    *The studies were carried out within the framework of a research project. The project was financed from funds of National Science Center on the base of decision number DEC-2013/11/D/NZ9/02545 Among many methods proposed to study sorption properties of soils an analysis of adsorption/ desorption isotherm is probably the easiest and most convenient one. It characterizes both quantity and quality of mineral and organic components and also their physical and physicochemical properties. The main aim of this study is comparison of sorption properties of selected Polish soils by using water vapour adsorption method. Samples were taken from the depth of 0-20 cm, from the Lublin region, eastern Poland. Soils were selected on the basis of their different physicochemical properties and were classified as: Haplic Fluvisol, Haplic Chernozem, Mollic Gleysol, Rendzic Phaeozem, Stagnic Luvisol, Haplic Cambisol (WG WRB 2006). Data taken from experimental adsorption isotherms were used to determine parameters of monolayer capacity, specific surface area and the total amount of vapour adsorbed at relative pressure of 0.974. Obtained adsorption and desorption isotherms reviled that adsorbate molecules interacted with the soil particles in different extent. Similar monolayer capacity was observed for Haplic Fluvisol, Haplic Chernozem and Stagnic Luvisol, while for Mollic Gleysol was more than 4 times higher. Mollic Gleysol was also characterized by highest values of specific surface area as well as quantity of adsorbed vapour at relative pressure of 0.974. Higher sorption was caused by presence of soil colloids which contains functional groups of a polar nature (mainly hydroxyls, phenolic and carboxyls). These groups similarly to silicates, oxides, hydratable cations as well as electric charge form adsorption centres for water vapour molecules.

  11. Effect of drilling fluid systems and temperature on oil mist and vapour levels generated from shale shaker.

    Science.gov (United States)

    Steinsvåg, Kjersti; Galea, Karen S; Krüger, Kirsti; Peikli, Vegard; Sánchez-Jiménez, Araceli; Sætvedt, Esther; Searl, Alison; Cherrie, John W; van Tongeren, Martie

    2011-05-01

    Workers in the drilling section of the offshore petroleum industry are exposed to air pollutants generated by drilling fluids. Oil mist and oil vapour concentrations have been measured in the drilling fluid processing areas for decades; however, little work has been carried out to investigate exposure determinants such as drilling fluid viscosity and temperature. A study was undertaken to investigate the effect of two different oil-based drilling fluid systems and their temperature on oil mist, oil vapour, and total volatile organic compounds (TVOC) levels in a simulated shale shaker room at a purpose-built test centre. Oil mist and oil vapour concentrations were sampled simultaneously using a sampling arrangement consisting of a Millipore closed cassette loaded with glass fibre and cellulose acetate filters attached to a backup charcoal tube. TVOCs were measured by a PhoCheck photo-ionization detector direct reading instrument. Concentrations of oil mist, oil vapour, and TVOC in the atmosphere surrounding the shale shaker were assessed during three separate test periods. Two oil-based drilling fluids, denoted 'System 2.0' and 'System 3.5', containing base oils with a viscosity of 2.0 and 3.3-3.7 mm(2) s(-1) at 40°C, respectively, were used at temperatures ranging from 40 to 75°C. In general, the System 2.0 yielded low oil mist levels, but high oil vapour concentrations, while the opposite was found for the System 3.5. Statistical significant differences between the drilling fluid systems were found for oil mist (P = 0.025),vapour (P < 0.001), and TVOC (P = 0.011). Increasing temperature increased the oil mist, oil vapour, and TVOC levels. Oil vapour levels at the test facility exceeded the Norwegian oil vapour occupational exposure limit (OEL) of 30 mg m(-3) when the drilling fluid temperature was ≥50°C. The practice of testing compliance of oil vapour exposure from drilling fluids systems containing base oils with viscosity of ≤2.0 mm(2) s(-1) at 40

  12. Optical studies on Sn, K, Hg{sub 2} I{sub 2}, and I{sub 2}-doped {alpha}-HgI{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez, M.; Ibarra, A.; Willmott, C.; Pascual, J. L.; Dieguez, E.

    1997-07-01

    The influence on the optical properties of {alpha}-mercuric iodide stoichiometric deviations have been investigated. The optical behaviour of samples doped with Sn (IV) and K were also studied. To prepare mercury-rich and iodide rich samples (non-stoichiometric compounds), vapour phase crystal growth was performed on a closed ampoule with a mercurous iodide or iodine atmosphere, respectively. Dopants were introduced through the vapour phase by means of Snl{sub 4} and KI vapours during crystal growth. A decrease in the energy gap is deduced from the optical absorption spectra taken on non-stoichiometric and doped samples. Photoluminescence was also performed as a function of temperature while samples were under uniaxial pressure. Differences between doped, non-stoichiometric and pure samples are observed on luminescence emission wavelength and intensity.

  13. Testing flow-through air samplers for use in near-field vapour drift studies by measuring pyrimethanil in air after spraying.

    Science.gov (United States)

    Geoghegan, Trudyanne S; Hageman, Kimberly J; Hewitt, Andrew J

    2014-03-01

    Pesticide volatilisation and subsequent vapour drift reduce a pesticide's efficiency and contribute to environmental contamination. High-volume air samplers (HVSs) are often used to measure pesticide concentrations in air but these samplers are expensive to purchase and require network electricity, limiting the number and type of sites where they can be deployed. The flow-through sampler (FTS) presents an opportunity to overcome these limitations. The FTS is a wind-driven passive sampler that has been developed to quantify organic contaminants in remote ecosystems. FTSs differ from other passive samplers in that they turn into the wind and use the wind to draw air through the sampling media. The main objective of this work was to evaluate the FTS in a near-field pesticide vapour drift study by comparing the concentrations of pyrimethanil in air measured using one HVS and three FTSs placed in the same location. Pyrimethanil was sprayed onto a vineyard as part of normal pest management procedures. Air samples were collected every eight hours for 48 h. The volume of air sampled by the FTSs was calculated using the measured relationship between ambient wind speed and the wind speed inside the sampler as determined with a separate wind tunnel study. The FTSs sampled 1.7 to 40.6 m(3) of air during each 8 h sampling period, depending on wind speed, whereas the mean volume sampled by the HVS was 128.7 m(3). Mean pyrimethanil concentrations ranged from 0.4 to 3.2 μg m(-3) of air. Inter-sampler reproducibility, as represented by percent relative standard deviation, for the three FTSs was ∼20%. The largest difference in FTS-derived versus HVS-derived pyrimethanil concentrations occurred during the lowest wind-speed period. During this period, it is likely that the FTS predominately acted like a traditional diffusion-based passive sampler. As indicated by both types of sampler, pyrimethanil concentrations in air changed by a factor of ∼2 during the two days after spaying

  14. The Upside to Hg-DOM Associations for Water Quality: Removal of Hg from Solution Using Coagulaion with Metal-Based Salts

    Science.gov (United States)

    Henneberry, Y.; Kraus, T. E.; Fleck, J.; Krabbenhoft, D. P.; Horwath, W. R.

    2011-12-01

    This study assessed the potential use of metal-based coagulants to remove dissolved mercury (Hg) from natural waters and provides information regarding the importance of Hg associations with the dissolved organic matter (DOM) fraction and metal hydroxides. Previous research indicated coagulants were not effective at removing Hg from solution; however those studies used high concentrations of Hg, which did not reflect naturally occurring concentrations of Hg. Filtered water collected from an agricultural drain in the Sacramento-San Joaquin Delta (Delta) was treated with three industrial-grade coagulants (ferric chloride, ferric sulfate, and polyaluminum chloride) to determine their efficacy in removing both inroganic (IHg) and methylmercury (MeHg) from the water column. The Delta suffers from elevated surface water Hg concentrations and as a result is listed as an imparied water body. Coagulants removed up to 85% of DOM from solution. In the absence of DOM, all three coagulants released IHg into solution, however in the presence of DOM the coagulants removed up to 97% of IHg and 80% of MeHg. Results suggest that the removal of Hg is mediated by DOM-coagulant interactions. There was a preferential association of IHg with the more aromatic, higher molecular weight fraction of DOM but no such relationship was found for MeHg. This study offers new fundamental insights regarding large-scale removal of Hg at environmentally relevant concentrations. Research using isotopically labeled Hg is providing insight into whether coagulation can remove recently added Hg (e.g. atmospheric deposition) from solution and whether once formed, the floc can remove additional Hg from the water column.

  15. Study of atomic structure of liquid Hg-In alloys using ab-initio molecular dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Sharma, Nalini; Ahluwalia, P. K. [Department of Physics, Himachal Pradesh University, Shimla(HP)-171005 (India); Thakur, Anil [Department of Physics, Govt. P. G. College Solan (HP)-173212 (India)

    2015-05-15

    Ab-initio molecular dynamics simulations are performed to study the structural properties of liquid Hg-In alloys. The interatomic interactions are described by ab-initio pseudopotentials given by Troullier and Martins. Five liquid Hg-In mixtures (Hg{sub 10}In{sub 90}, Hg{sub 30}In{sub 70}, Hg{sub 50}In{sub 50}, Hg{sub 70}In{sub 30} and Hg{sub 90}In{sub 10}) at 299K are considered. The radial distribution function g(r) and structure factor S(q) of considered alloys are compared with respective experimental results for liquid Hg (l-Hg) and (l-In). The radial distribution function g(r) shows the presence of short range order in the systems considered. Smooth curves of Bhatia-Thornton partial structure factors factor shows the presence of liquid state in the considered alloys.

  16. Investigation of the vapour-plasma plume in the welding of titanium by high-power ytterbium fibre laser radiation

    Science.gov (United States)

    Bykovskiy, D. P.; Petrovskii, V. N.; Uspenskiy, S. A.

    2015-03-01

    The vapour-plasma plume produced in the welding of 6-mm thick VT-23 titanium alloy plates by ytterbium fibre laser radiation of up to 10 kW power is studied in the protective Ar gas medium. High-speed video filming of the vapour-plasma plume is used to visualise the processes occurring during laser welding. The coefficient of inverse bremsstrahlung by the welding plasma plume is calculated from the data of the spectrometric study.

  17. Simulation of the isotopic composition of stratospheric water vapour - Part 2: Investigation of HDO / H2O variations

    Science.gov (United States)

    Eichinger, R.; Jöckel, P.; Lossow, S.

    2015-06-01

    Studying the isotopic composition of water vapour in the lower stratosphere can reveal the driving mechanisms of changes in the stratospheric water vapour budget and therefore help to explain the trends and variations of stratospheric water vapour during recent decades. We equipped a global chemistry climate model with a description of the water isotopologue HDO, comprising its physical and chemical fractionation effects throughout the hydrological cycle. We use this model to improve our understanding of the processes which determine the patterns in the stratospheric water isotope composition and in the water vapour budget itself. The link between the water vapour budget and its isotopic composition in the tropical stratosphere is presented through their correlation in a simulated 21-year time series. The two quantities depend on the same processes; however, they are influenced with different strengths. A sensitivity experiment shows that fractionation effects during the oxidation of methane have a damping effect on the stratospheric tape recorder signal in the water isotope ratio. Moreover, the chemically produced high water isotope ratios overshadow the tape recorder in the upper stratosphere. Investigating the origin of the boreal-summer signal of isotopically enriched water vapour reveals that in-mixing of old stratospheric air from the extratropics and the intrusion of tropospheric water vapour into the stratosphere complement each other in order to create the stratospheric isotope ratio tape recorder signal. For this, the effect of ice lofting in monsoon systems is shown to play a crucial role. Furthermore, we describe a possible pathway of isotopically enriched water vapour through the tropopause into the tropical stratosphere.

  18. Validation of stratospheric water vapour measurements from the airborne microwave radiometer AMSOS

    Directory of Open Access Journals (Sweden)

    S. C. Müller

    2008-01-01

    Full Text Available We present the validation of a water vapour dataset obtained by the Airborne Microwave Stratospheric Observing System AMSOS, a passive microwave radiometer operating at 183 GHz. Vertical profiles are retrieved from spectra by an optimal estimation method. The useful vertical range lies in the upper troposphere up to the mesosphere with an altitude resolution of 8 to 16 km and a horizontal resolution of about 57 km. Flight campaigns were performed once a year from 1998 to 2006 measuring the latitudinal distribution of water vapour from the tropics to the polar regions. The obtained profiles show clearly the main features of stratospheric water vapour in all latitudinal regions. Data are validated against a set of instruments comprising satellite, ground-based, airborne remote sensing and in-situ instruments. It appears that AMSOS profiles have a dry bias of 3–20%, when compared to satellite experiments. A good agreement with a difference of 3.3% was found between AMSOS and in-situ hygrosondes FISH and FLASH and an excellent matching of the lidar measurements from the DIAL instrument in the short overlap region in the upper troposphere.

  19. Production of sulphate-rich vapour during the Chicxulub impact and implications for ocean acidification

    Science.gov (United States)

    Ohno, Sohsuke; Kadono, Toshihiko; Kurosawa, Kosuke; Hamura, Taiga; Sakaiya, Tatsuhiro; Shigemori, Keisuke; Hironaka, Yoichiro; Sano, Takayoshi; Watari, Takeshi; Otani, Kazuto; Matsui, Takafumi; Sugita, Seiji

    2014-04-01

    The mass extinction event at the Cretaceous/Palaeogene boundary 65.5 Myr ago has been widely attributed to the Chicxulub impact, but the mechanisms of extinction remain debated. In the oceans, near-surface planktonic foraminifera suffered severe declines, in contrast to the relatively high survival rates of bottom-dwelling benthic foraminifera. The vapour produced by an impact into Chicxulub's target rocks, which include sulphate-rich anhydrite, could have led to global acid rain, which can explain the pattern of oceanic extinctions. However, it has been suggested that most of the sulphur in the target rocks would have been released as sulphur dioxide and would have stayed in the stratosphere for a long time. Here we show, from impact experiments into anhydrite at velocities exceeding 10 km s-1, that sulphur trioxide dominates over sulphur dioxide in the resulting vapour cloud. Our experiments suggest that the Chicxulub impact released a huge quantity of sulphur trioxide into the atmosphere, where it would have rapidly combined with water vapour to form sulphuric acid aerosol particles. We also find, using a theoretical model of aerosol coagulation following the Chicxulub impact, that larger silicate particles ejected during the impact efficiently scavenge sulphuric acid aerosol particles and deliver the sulphuric acid to the surface within a few days. The rapid surface deposition of sulphuric acid would cause severe ocean acidification and account for preferential extinction of planktonic over benthic foraminifera.

  20. The effects of acute gasoline vapour inhalation on some haematological indices of albino Wistar rats

    Institute of Scientific and Technical Information of China (English)

    Chukwudi Onyeka John Okonkwo; Ailende Daniel Ehileboh; Eddy Nwobodo; Charles Chijioke Dike

    2016-01-01

    Objective: To find out if Gasoline vapour has some effects on haematological indices when inhaled by experimental rats. Methods: The standard method for laboratory operating procedure recommended by World Health Organization was used in all the analysis done. Forty two albino Wistar rats comprising twenty one males (160–220 g) and twenty one females (140–190 g) were sampled into six groups consisting of four test groups and two control groups. The test groups were exposed to gasoline vapour for twenty one days. Test group one were exposed to gasoline for 30 min while test group two were exposed to gasoline vapour for 1 h daily. At the end of twenty one days of exposure, blood samples were collected from the rats and their haematological parameters were estimated. Statistical analysis was done using windows SPSS version 16. Results: The results showed a significant decrease (P Conclusions: The results obtained suggest that inhalation exposure to gasoline may result in pancytopaenia and a significant fluctuation in the red blood cell-dependent haematological indices.

  1. Explicit modelling of SOA formation from α-pinene photooxidation: sensitivity to vapour pressure estimation

    Directory of Open Access Journals (Sweden)

    J. H. Seinfeld

    2011-03-01

    Full Text Available The sensitivity of the formation of secondary organic aerosol (SOA to the estimated vapour pressures of the condensable oxidation products is explored. A highly detailed reaction scheme was generated for α-pinene photooxidation using the Generator for Explicit Chemistry and Kinetics of Organics in the Atmosphere (GECKO-A. Vapour pressures (Pvap were estimated with three commonly used structure activity relationships. The values of Pvap were compared for the set of secondary species generated by GECKO-A to describe α-pinene oxidation. Discrepancies in the predicted vapour pressures were found to increase with the number of functional groups borne by the species. For semi-volatile organic compounds (i.e. organic species of interest for SOA formation, differences in the predicted Pvap range between a factor of 5 to 200 in average. The simulated SOA concentrations were compared to SOA observations in the Caltech chamber during three experiments performed under a range of NOx conditions. While the model captures the qualitative features of SOA formation for the chamber experiments, SOA concentrations are systematically overestimated. For the conditions simulated, the modelled SOA speciation appears to be rather insensitive to the Pvap estimation method.

  2. Explicit modelling of SOA formation from α-pinene photooxidation: sensitivity to vapour pressure estimation

    Directory of Open Access Journals (Sweden)

    R. Valorso

    2011-07-01

    Full Text Available The sensitivity of the formation of secondary organic aerosol (SOA to the estimated vapour pressures of the condensable oxidation products is explored. A highly detailed reaction scheme was generated for α-pinene photooxidation using the Generator for Explicit Chemistry and Kinetics of Organics in the Atmosphere (GECKO-A. Vapour pressures (Pvap were estimated with three commonly used structure activity relationships. The values of Pvap were compared for the set of secondary species generated by GECKO-A to describe α-pinene oxidation. Discrepancies in the predicted vapour pressures were found to increase with the number of functional groups borne by the species. For semi-volatile organic compounds (i.e. organic species of interest for SOA formation, differences in the predicted Pvap range between a factor of 5 to 200 on average. The simulated SOA concentrations were compared to SOA observations in the Caltech chamber during three experiments performed under a range of NOx conditions. While the model captures the qualitative features of SOA formation for the chamber experiments, SOA concentrations are systematically overestimated. For the conditions simulated, the modelled SOA speciation appears to be rather insensitive to the Pvap estimation method.

  3. Assessment of pumped mercury vapour adsorption tubes as passive samplers using a micro-exposure chamber.

    Science.gov (United States)

    Brown, Richard J C; Burdon, Melia K; Brown, Andrew S; Kim, Ki-Hyun

    2012-09-01

    Mercury vapour adsorption tubes manufactured for pumped sampling and analysis have been evaluated for their performance as passive samplers. This has been done by exposing these tubes in a novel micro-exposure chamber. The uptake rates of these tubes have been found to be low (approximately 0.215 ml min(-1)) as compared to bespoke passive samplers for mercury vapour (typically in excess of 50 ml min(-1)). The measured uptake rates were shown to vary significantly between tubes and this was attributed to the variability in the air-sorbent interface and the proportion of the cross sectional area removed by the crimp in the quartz tubes used to secure the sorbent material. As a result of this variability the uptake rate of each tube must be determined using the micro-exposure chamber prior to deployment. Results have shown that the uptake rate determined in the micro-exposure chamber is invariant of concentration, and therefore these uptakes rates may be determined at a high mercury vapour concentration for many tubes at once in less than one hour. The uptake rate of the adsorption tubes under these conditions may be determined with a precision of 5%. Measurements made on a limited field trial in indoor and outdoor ambient air have shown that these tubes give results in acceptable agreement with more traditional pumped sampling methods, although longer sampling periods are required in order to reduce the uncertainty of the measurement, which is currently approximately 30%.

  4. Steady-state molecular dynamics simulation of vapour to liquid nucleation with McDonald's daemon

    CERN Document Server

    Horsch, Martin; Vrabec, Jadran

    2009-01-01

    The most interesting step of condensation is the cluster formation up to the critical size. In a closed system, this is an instationary process, as the vapour is depleted by the emerging liquid phase. This imposes a limitation on direct molecular dynamics (MD) simulation of nucleation by affecting the properties of the vapour to a significant extent so that the nucleation rate varies over simulation time. Grand canonical MD with McDonald's daemon is discussed in the present contribution and applied for sampling both nucleation kinetics and steady-state properties of a supersaturated vapour. The idea behind that approach is to simulate the production of clusters up to a given size for a specified supersaturation. In that way, nucleation is studied by a steady-state simulation. A series of simulations is conducted for the truncated and shifted Lennard-Jones fluid which accurately describes the fluid phase coexistence of noble gases and methane. The classical nucleation theory is found to overestimate the free e...

  5. Strategies for 4-D Regional Modeling of Water Vapour Using GPS

    Institute of Scientific and Technical Information of China (English)

    S. H. Skone; S.M. Shrestha

    2003-01-01

    Global Positioning System (GPS) signals experience ranging errors due to propagation through the neutral atmosphere. These range delays consist of a hydrostatic component, dependent on air pressure and temperature, and a wet delay dependent on water vapour pressure and temperature.Range delays arising from the hydrostatic component can be computed with accuracies of a few millimeters using existing models, provided that surface barometric or meteorological data are available. By using a regional network of GPS reference stations, it is possible to recover estimates of the Slant Wet Delay to all satellites in view. Observations of the Slant Wet Delay (SWD) can be used to model the vertical and horizontal structure of water vapour over a local area. These techniques are based on a tomographic approach using the SWD as input observables, where 4-D models of the wet refractivity may be derived. This method allows improved resolution of water vapour estimates for precise positioning applications and assimilation into Numerical Weather Predictions (NWP). In this paper we present strategies for real-time modeling of wet refractivity, with simulations and preliminary results of data processing for a regional GPS network in Southern California.

  6. Atomic-scale Studies of Uranium Oxidation and Corrosion by Water Vapour

    Science.gov (United States)

    Martin, T. L.; Coe, C.; Bagot, P. A. J.; Morrall, P.; Smith, G. D. W; Scott, T.; Moody, M. P.

    2016-01-01

    Understanding the corrosion of uranium is important for its safe, long-term storage. Uranium metal corrodes rapidly in air, but the exact mechanism remains subject to debate. Atom Probe Tomography was used to investigate the surface microstructure of metallic depleted uranium specimens following polishing and exposure to moist air. A complex, corrugated metal-oxide interface was observed, with approximately 60 at.% oxygen content within the oxide. Interestingly, a very thin (~5 nm) interfacial layer of uranium hydride was observed at the oxide-metal interface. Exposure to deuterated water vapour produced an equivalent deuteride signal at the metal-oxide interface, confirming the hydride as originating via the water vapour oxidation mechanism. Hydroxide ions were detected uniformly throughout the oxide, yet showed reduced prominence at the metal interface. These results support a proposed mechanism for the oxidation of uranium in water vapour environments where the transport of hydroxyl species and the formation of hydride are key to understanding the observed behaviour. PMID:27403638

  7. Backtrajectory reconstruction of water vapour and ozone in-situ observations in the TTL

    Energy Technology Data Exchange (ETDEWEB)

    Ploeger, F.; Konopka, P.; Mueller, R.; Guenther, G.; Grooss, J.U.; Schiller, C.; Riese, M. [Forschungszentrum Juelich (DE). Inst. fuer Energie- und Klimaforschung (IEK-7); Ravegnani, F. [ISAC-CNR, Bologna (Italy). Inst. of Atmospheric Sciences and Climate; Ulanovski, A. [CAO, Dolgoprudny (Russian Federation)

    2012-06-15

    Water vapour and ozone in-situ observations in the tropical tropopause layer (TTL) during the three tropical campaigns SCOUT-O3, AMMA and TroCCiNOx are reconstructed from diabatic and kinematic backtrajectories, with the reconstruction method for the tracer fields based on freeze-drying and photochemichal ozone production. The results using diabatic trajectories show that both water vapour and ozone in-situ observations can be well reconstructed from trajectories. Consequentially, in-situ observations agree with the assumption of freeze-drying due to the large-scale temperature field as the main control mechanism for water vapour and photochemical production and transport as main control mechanisms for tropical ozone. The kinematic ozone reconstruction, however, shows a large high-bias during SCOUT-O3 and a too strong variability during all campaigns, due to excessive transport of stratospheric ozone into the TTL. We conclude that kinematic reconstructions of in-situ observations are less reliable than diabatic, due to unrealistic inhomogeneities in the velocity field. (orig.)

  8. Tar reduction in pyrolysis vapours from biomass over a hot char bed.

    Science.gov (United States)

    Gilbert, P; Ryu, C; Sharifi, V; Swithenbank, J

    2009-12-01

    The behaviour of pyrolysis vapours over char was investigated in order to maximise tar conversion for the development of a new fixed bed gasifier. Wood samples were decomposed at a typical pyrolysis temperature (500 degrees C) and the pyrolysis vapours were then passed directly through a tar cracking zone in a tubular reactor. The product yields and properties of the condensable phases and non-condensable gases were studied for different bed lengths of char (0-450 mm), temperatures (500-800 degrees C), particle sizes (10 and 15 mm) and nitrogen purge rates (1.84-14.70 mm/s). The carbon in the condensable phases showed about 66% reduction by a 300 mm long char section at 800 degrees C, compared to that for pyrolysis at 500 degrees C. The amount of heavy condensable phase decreased with increasing temperature from about 18.4 wt% of the biomass input at 500 degrees C to 8.0 wt% at 800 degrees C, forming CO, H(2) and other light molecules. The main mode of tar conversion was found to be in the vapour phase when compared to the results without the presence of char. The composition of the heavy condensable phase was simplified into much fewer secondary and tertiary tar components at 800 degrees C. Additional measures were required to maximise the heterogeneous effect of char for tar reduction.

  9. Oscillatory vapour shielding of liquid metal walls in nuclear fusion devices.

    Science.gov (United States)

    van Eden, G G; Kvon, V; van de Sanden, M C M; Morgan, T W

    2017-08-04

    Providing an efficacious plasma facing surface between the extreme plasma heat exhaust and the structural materials of nuclear fusion devices is a major challenge on the road to electricity production by fusion power plants. The performance of solid plasma facing surfaces may become critically reduced over time due to progressing damage accumulation. Liquid metals, however, are now gaining interest in solving the challenge of extreme heat flux hitting the reactor walls. A key advantage of liquid metals is the use of vapour shielding to reduce the plasma exhaust. Here we demonstrate that this phenomenon is oscillatory by nature. The dynamics of a Sn vapour cloud are investigated by exposing liquid Sn targets to H and He plasmas at heat fluxes greater than 5 MW m(-2). The observations indicate the presence of a dynamic equilibrium between the plasma and liquid target ruled by recombinatory processes in the plasma, leading to an approximately stable surface temperature.Vapour shielding is one of the interesting mechanisms for reducing the heat load to plasma facing components in fusion reactors. Here the authors report on the observation of a dynamic equilibrium between the plasma and the divertor liquid Sn surface leading to an overall stable surface temperature.

  10. Atomic-scale Studies of Uranium Oxidation and Corrosion by Water Vapour

    Science.gov (United States)

    Martin, T. L.; Coe, C.; Bagot, P. A. J.; Morrall, P.; Smith, G. D. W.; Scott, T.; Moody, M. P.

    2016-07-01

    Understanding the corrosion of uranium is important for its safe, long-term storage. Uranium metal corrodes rapidly in air, but the exact mechanism remains subject to debate. Atom Probe Tomography was used to investigate the surface microstructure of metallic depleted uranium specimens following polishing and exposure to moist air. A complex, corrugated metal-oxide interface was observed, with approximately 60 at.% oxygen content within the oxide. Interestingly, a very thin (~5 nm) interfacial layer of uranium hydride was observed at the oxide-metal interface. Exposure to deuterated water vapour produced an equivalent deuteride signal at the metal-oxide interface, confirming the hydride as originating via the water vapour oxidation mechanism. Hydroxide ions were detected uniformly throughout the oxide, yet showed reduced prominence at the metal interface. These results support a proposed mechanism for the oxidation of uranium in water vapour environments where the transport of hydroxyl species and the formation of hydride are key to understanding the observed behaviour.

  11. ANNEALING OF POLYCRYSTALLINE THIN FILM SILICON SOLAR CELLS IN WATER VAPOUR AT SUB-ATMOSPHERIC PRESSURES

    Directory of Open Access Journals (Sweden)

    Peter Pikna

    2014-10-01

    Full Text Available Thin film polycrystalline silicon (poly-Si solar cells were annealed in water vapour at pressures below atmospheric pressure. PN junction of the sample was contacted by measuring probes directly in the pressure chamber filled with steam during passivation. Suns-VOC method and a Lock-in detector were used to monitor an effect of water vapour to VOC of the solar cell during whole passivation process (in-situ. Tested temperature of the sample (55°C – 110°C was constant during the procedure. Open-circuit voltage of a solar cell at these temperatures is lower than at room temperature. Nevertheless, voltage response of the solar cell to the light flash used during Suns-VOC measurements was good observable. Temperature dependences for multicrystalline wafer-based and polycrystalline thin film solar cells were measured and compared. While no significant improvement of thin film poly-Si solar cell parameters by annealing in water vapour at under-atmospheric pressures was observed up to now, in-situ observation proved required sensitivity to changing VOC at elevated temperatures during the process.

  12. Removal of Hg~0 with sodium chlorite solution and mass transfer reaction kinetics

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    The absorption behavior of Hg0 was studied experimentally by using sodium chlorite solution(NaClO2) as the absorbent in a bubble reactor.Primary influencing factors on removal efficiency of Hg0 such as NaClO2 concentration,pH,reaction temperature and the concentration of Hg0 were investigated.The results indicated that 72.91% of Hg0 removal efficiency could be achieved in acidic NaClO2 solution.The removal mechanism of Hg0 was proposed by analyzing of Hg2+ concentration in ab-sorption solution after reaction and comparing the electrode potentials between NaClO2 species and Hg2+/Hg0.The experimental results of mass transfer-reaction kinetics on oxidation of Hg0 by NaClO2 solution showed that with the increase of NaClO2 concentration and the decrease of pH value,the enhancement factor(E) and ratio of KG(Hg0)/kG(Hg0) increased and the liquid phase mass transfer resistance decreased,which is benefit to the mass transfer adsorption reaction.Although the increase of reaction temperature could improve the enhancement factor(E),but the ratio of KG(Hg0)/kG(Hg0) decreased;as a result,the liquid phase mass transfer resistance increased,therefore,the reaction rate for removal of Hg0 decreased.

  13. 640 X 480 Pace HgCdTe FPA

    Science.gov (United States)

    Kozlowski, Lester J.; Bailey, Robert B.; Cabelli, Scott A.; Cooper, Donald E.; McComas, Gail D.; Vural, Kadri; Tennant, William E.

    1992-12-01

    A hybrid HgCdTe 640 X 480 infrared (IR) focal plane array (FPA) that meets the sensitivity, resolution, and field-of-view requirements of high-performance medium wavelength infrared (MWIR) imaging systems has been developed. The key technology making this large, high sensitivity device producible is the epitaxial growth of HgCdTe on a CdTe-buffered, sapphire substrate (referred to as PACE, for Producible Alternative to CdTe for Epitaxy; PACE-I refers to sapphire). The device offers TV resolution with excellent sensitivity at temperatures below 120 K. Mean NE(Delta) T as low as 13 mK has been achieved at operating temperatures nonuniformity compensation.

  14. Electrical Conductivity of HgTe at High Temperatures

    Science.gov (United States)

    Li, C.; Lehoczky, S. L.; Su, C.-H.; Scripa, R. N.

    2004-01-01

    The electrical conductivity of HgTe was measured using a rotating magnetic field method from 300 K to the melting point (943 K). A microscopic theory for electrical conduction was used to calculate the expected temperature dependence of the HgTe conductivity. A comparison between the measured and calculated conductivities was used to obtain the estimates of the temperature dependence of Gamma(sub 6)-Gamma(sub 8) energy gap from 300 K to 943 K. The estimated temperature coefficient for the energy gap was comparable to the previous results at lower temperatures (less than or equal to 300 K). A rapid increase in the conductivity just above 300 K and a subsequent decrease at 500 K is attributed to band crossover effects. This paper describes the experimental approach and some of the theoretical calculation details.

  15. Electronic structure of rectangular HgTe quantum dots

    Science.gov (United States)

    Li, Jian; Zhang, Dong; Zhu, Jia-Ji

    2017-09-01

    We theoretically investigate the single- and few-electron ground-states properties of HgTe topological insulator quantum dots with rectangular hard-wall confining potential using configuration interaction method. For the case of single electron, the edge states is robust against the deformation from a square quantum dot to a rectangular ones, in contrast to the bulk states, the energy gap of the QDs increased due to the coupling of the opposite edge states; for the case of few electrons, the electrons first fill the edge states in the bulk band gap and the addition energy exhibit universal even-odd oscillation due to the shape-independent two-fold degeneracy of the edge states. The size of this edge shell can be controlled by tuning the dot size, shape or the bulk band gap via lateral or vertical electric gating respectively of the HgTe quantum dot.

  16. Hvordan understøttes hg-elevers kompetenceudvikling

    DEFF Research Database (Denmark)

    Svejgaard, Karin Løvenskjold; Hansen, Jens Ager; Karmark, Ole

    Publikationen handler om, hvordan hg-elever arbejder og dermed lærer og udvikler kvalifikationer og kompetencer i de undervisnings- og arbejdsformer, de indgår i. Indholdet er baseret på observationer af elever i klasseundervisning, gruppearbejde eller individuel arbejde i forlængelse af...... klasseundervisning og af elever i projektarbejde. Observationerne er gennemført på tre jyske handelsskoler....

  17. Net water vapour exchange over a mixed needle and broad-leaved forest in Changbai Mountain during autumn

    Institute of Scientific and Technical Information of China (English)

    HANShijie; WENXuefa; YUGuirui; SUNXiaomin; LIQingkang; RENChuanyou

    2003-01-01

    Water vapour and CO2 fluxes were measured by the eddy-covariance technique above a mixed needle and broad-leaved forest with affiliated meteorological measurements in Changbai Mountain as part of China's FLUX projects since late August in 2002. Net water vapour exchange and environmental control over the forest were examined from September 1 to October 31 in 2002. To quantify the seasonal dynamics, the transition period was separated into leafed, leaf falling and leafless stages according to the development of leaf area. The results showed that (a) seasonal variation of water vapour exchange was mainly controlled by net radiation (Rn) which could account for 78.5%, 63.4% and 56.6% for leafed, leaf falling and leafless stages, respectively, while other environmental factors' effects varied evidently; (b) magnitude of water vapour flux decreased remarkably during autumn and daily mean of water vapour exchange was 24.2 mg m-2 s-1 (100%), 14.8 mg m-2 s-1 (61.2%) and 10.3 mg m-2 s-1 (42.6%) for leafed, leaf falling and leafless stage, respectively; and (c) the budget of water vapour exchange during autumn was estimated to be 87.1 kg H2O m2, with a mean of 1427.2 g H2O d-1 varying markedly from 3104.0 to 227.5 g H2O m-2d-1.

  18. EDTA and urease effects on Hg accumulation by Lepidium sativum.

    Science.gov (United States)

    Smolińska, Beata; Cedzyńska, Krystyna

    2007-11-01

    The phytoextraction process was conducted under laboratory conditions with the use of garden cress plants (Lepidium sativum). The experiment was carried out in a model soil, which was characterized before conducting the process. Inorganic forms of mercury (HgCl(2), HgSO(4), Hg(NO(3))(2)) were used for contamination of the soil. The phytoextraction process was conducted after EDTA application to the soil and after urease application. Also the influence of simultaneous addition of ethylenediaminetetraacetic acid (EDTA) and urease into the soil on phytoextraction process was measured. In all variants of phytoextraction process the total mercury concentrations in roots, stems and leaves of garden cress were determined. The result showed that garden cress accumulated mercury from soil. The overall maximum concentration of mercury in its compounds was found in roots of the plant. In all cases, before addition of urease and EDTA, the translocation process and distribution of mercury in the plant tissues were limited. The addition of urease caused an increase of enzyme activity in the soil and at the same time caused an increase of mercury concentration in plant tissues. Application of EDTA increased solubility of mercury and caused an increase of metal accumulation by plants. After simultaneous addition of EDTA and urease into the soil garden cress accumulated about 20% of total mercury concentration in the soil. Most of mercury compounds were accumulated in leaves and stems of the plants (46.0-56.9% of total mercury concentration in the plant tissues).

  19. Barrier formation at graded HgTe/CdTe heterojunctions

    Science.gov (United States)

    Goren, D.; Asa, G.; Nemirovsky, Y.

    1996-11-01

    Numerical calculations of graded HgTe/CdTe heterojunction (HJ) band diagrams at equilibrium are presented and discussed. The calculations are performed in the entire compositional range (0HJs are examined as a function of the graded region width and the graded region doping profiles. The graded region width and doping profiles were found to be the two main factors that determine whether barriers are formed as well as their shape and magnitude. The calculated results indicate that epitaxial ohmic HgTe contacts to extrinsic CdTe are possible, provided that the graded region is wider than one micron, and that it has the same doping type as the doping of the substrate with equal or higher absolute value. Further numerical calculations take into consideration the possible existence of distributed interface charges in the graded region of the HJ. It is shown that by assuming a classical transport over the potential barrier, the effective graded interface charge can be determined from the zero bias differential resistance of the HJ. Experimental transport measurements of metalorganic chemical vapor deposition (MOCVD) grown HgTe/p-CdTe graded HJs show a varying degree of rectification, indicating variations in the graded interface charge distributions which result from different MOCVD growth conditions.

  20. Final report on CCQM-K70: Determination of Hg in natural water at a concentration level required by the European environmental quality standard (EQS)

    Science.gov (United States)

    Schiel, Detlef; Rienitz, Olaf

    2011-01-01

    This comparison 'Hg in natural water' was a follow-up to the pilot studies CCQM-P100.1 and CCQM-P100.2. The aim of this comparison was to demonstrate the capability of national metrology institutes to measure the Hg mass concentration in a natural water sample at the very low concentration level of γ(Hg) ≈ 70 ng/L as required by the EQS. In this way it served to help implement the European Water Framework Directive (WFD). This comparison was an activity of the Inorganic Analysis Working Group (IAWG) of CCQM and was piloted by Physikalisch-Technische Bundesanstalt (PTB, Braunschweig, Germany) with the help of the co-organizers Bundesanstalt für Materialforschung und -prüfung (BAM, Berlin, Germany), Laboratoire National de Métrologie et d'Essais (LNE, Paris, France), and the Joint Research Centre-Institute for Reference Materials and Measurements (EC-JRC-IRMM, Geel, Belgium). The following laboratories participated in this key comparison (in alphabetical order): BAM (Germany) EC-JRC-IRMM (European Union) KRISS (Republic of Korea) LGC (United Kingdom) LNE (France) NIST (United States of America) NMIA (Australia) NRC (Canada) PTB (Germany) SP (Sweden) The majority of participants applied isotope dilution mass spectrometry (IDMS) using sector field or quadrupole inductively coupled plasma MS (ICP-MS) in combination with cold vapour (CV) generation as the analytical technique. NRC reported a combined result of ID-CV-ICP-MS and CV atomic absorption spectrometry (CV-AAS). SP applied a standard addition method on a sector field ICP-MS, while BAM made use of an external 5-point calibration on a CV atomic fluorescence spectrometer (AFS). The key comparison reference value (KCRV) was agreed upon during the IAWG meeting in April 2010 at BIPM as the sum of the added Hg content calculated from the gravimetric sample preparation and the Hg matrix content of the water used for sample preparation (determined and validated on two independent pathways). Accordingly the degrees